WorldWideScience

Sample records for formuvannya ta vlastivostyi

  1. Carbonitrides in the system Ta-TaC-TaN

    International Nuclear Information System (INIS)

    Ritzhaupt-Kleissl, H.J.

    1975-04-01

    Specimens have been prepared in the binary section TaC-TaN and the carbon-rich region of the Ta-TaC-TaN system by hot pressing and subsequent homogenisation. It was possible to prepare nitrogen-rich carbonitrides by homogenizing them at 1,800 0 C under a nitrogen-pressure of 50 at up to the composition of 70 mol% TaN/30 mol% TaC. Those carbonitrides containing less than 25 at% nitrogen could be prepared by homogenisation at 2,000 0 C under a nitrogen-pressure of 600 Torr. Subsequent ageing at temperatures of 1,200, 1,300 and 1,400 0 C in high vacuum as well as at 1 at nitrogen resulted in the appearance of precipitations of epsilon-TaN, β-Ta 2 (C,N) and of the zeta-phase. The type amount and shape of the precipitated phases are dependent on the ageing conditions and on the composition the specimens. Single phase specimens with compositions close to the non-metal deficient phase boundary as well as multi-phase carbonitrides with high nitrogen contents and very fine precipitates showed values of the Vickers-hardness up to 3,000 kp/mm 2 at room temperature. With regard to the hot hardness up to a temperature of 1,300 0 C specimens aged in high vacuum were superior to those which were only homogenized as well as to those aged under a nitrogen-pressure of 1 at. On an average the best hardness-values have been found at room temperature as well as at temperatures up to 1,300 0 C for carbonitrides consisting of 50 mol% TaC/50 mol% TaN after homogenisation and subsequent ageing for 40 h at 1,300 0 C. (orig.) [de

  2. Comparative study of Ta, TaN and Ta/TaN bi-layer barriers for Cu-ultra low-k porous polymer integration

    International Nuclear Information System (INIS)

    Yang, L.Y.; Zhang, D.H.; Li, C.Y.; Foo, P.D.

    2004-01-01

    Tantalum (Ta), TaN and bilayer Ta/TaN barriers deposited on ultra-low-k porous polymer (ULKPP) and the thermal stability of their structures are comparatively investigated using various techniques. The Ta/ultra-low-k polymer shows the smallest sheet resistance, but the poorest thermal stability, while TaN on the ultra-low-k polymer shows the highest resistance but the best thermal stability. The bi-layer Ta/TaN barrier takes the advantage of both Ta and TaN barriers and gives reasonable resistance and thermal stability. The electrical tests indicate that the Cu lines with the TaN and bi-layer Ta/TaN barriers exhibit the smaller leakage current and higher breakdown voltage compared with the Cu lines with the Ta barrier. The better thermal stability of the TaN and the bi-layer Ta/TaN barriers is mainly due to the amorphous/nanostructure and less grain boundaries of the barriers. In addition, the texture discontinuity at the Ta/TaN interfaces in the bi-layers barrier also plays an important role in reducing mutual diffusion of Ta atoms in the Ta barrier and some atoms in the ultra-low-k porous polymer

  3. Corrosion Characteristics of Ti-xTa Alloys with Ta contents

    International Nuclear Information System (INIS)

    Kim, H. J.; Choe, H. C.

    2013-01-01

    The purpose of this study was to investigate corrosion characteristics of Ti-xTa alloys with Ta contents. Ti-xTa alloys used as samples (x=30, 40%) were arc-melted under argon atmosphere of 99.9% purity. Ti-xTa alloys were homogenized for 12hr at 1000 .deg. C and then water quenched. The surface characteristics of Ti-xTa alloys were investigated using optical microscopy (OM) and X-ray diffractometer (XRD). The anodic corrosion behaviors of the specimens were examined through potentiodynamic, potentiostatic and galvanostatic test in 0.9 % NaCl solution at 36.5 ± 1 .deg. C. After corrosion test, the surface characteristics of Ti-xTa alloys were investigated using OM. The microstructure of Ti-Ta alloy showed the beta structure with Ta content. The corrosion resistance of Ti alloy was improved by increasing Ta content and the corrosion morphology of Ti-Ta alloy showed that the site attacked by chloride ion decreased from the active to passive region with Ta content. Potential of Ti-40Ta alloy increased as time increased, whereas, current density of Ti-40Ta alloy decreased as time increased compared to Ti-30 alloy

  4. Radiological soil survey adjacent to TA-35, TA-48, TA-50, and TA-55

    International Nuclear Information System (INIS)

    Purtymun, W.D.; Becker, N.M.; Maes, M.N.

    1985-01-01

    The 137 Cs concentrations in soil from five new locations (in technical areas where radioactive materials are processed or have been processed) are at or below the maximum levels (1.4 pCi/g) found in regional soils. The 238 Pu and /sup 239,240/Pu soil concentrations at Station 2 were greater than were those found in regional soils (1977 and 1978-1982 Summaries). Station 2 is located south of TA-50. The total uranium soil concentrations exceed regional background concentrations at all stations. However, these levels do not indicate contamination but reflect natural uranium leached from soil derived from the tuff. These concentrations are similar to the data collected in 1977. Uranium concentrations in soils vary and depend on the rock type that has weathered to form the soil. A comparison of the averages and standard deviations of radiochemical analyses collected in 1977 and 1983 indicates only slight variations between the 2 yr. The five new stations established in 1983 will provide long-term monitoring of the possible airborne deposition of contaminants in the areas around TA-35, TA-48, TA-50, and TA-55. Comparing 1977 with 1983 data indicates no significant increase in radioactivity of the soil adjacent to these technical areas

  5. NMR-ON of 182Ta and 183Ta in Fe

    International Nuclear Information System (INIS)

    Allsop, A.L.; Chaplin, D.H.; Murray, D.W.; Stone, N.J.

    1980-01-01

    Nuclear magnetic resonance has been observed on radioactive 182 Ta and 183 Ta oriented at low temperature in an Fe host, by detection of the change in spatial anisotropy of γ-rays emitted during nuclear decay. By measuring the resonant frequencies of 183 Ta in four different applied magnetic fields the nuclear magnetic moment and hyperfine field have been deduced. These are: vertical stroke μ( 183 Ta;I = 7/2) = 2.28(3)μsub(N) and Bsub(h)sub(f)(TaFe at 0 K) = -67.2(1.3)T. The sin of the ground state of 182 Ta has been determined as I = 3 by comparing resonance results with those obtained in a thermal equilibrium nuclear orientation study. The ratio of the resonant frequencies observed for 182 Ta and 183 Ta at one applied field value yields a magnetic moment for the former of vertical stroke μ( 182 Ta;I = 3) vertical stroke = 2.91(3)μsub(N). The spin lattice relaxation time for 183 TaFe (0.12 at% Ta) at 18 mK in an applied field of 0.5 T has been found to be 40(10)s. (orig.)

  6. 179Ta and 180Ta structure by transfer reactions

    International Nuclear Information System (INIS)

    Warde, Elias.

    1979-01-01

    Transfer reactions (α,t); ( 3 He,d); (p,t) and (p,d) have been used to study the nuclear spectroscopy of 179 Ta and 180 Ta. In 179 Ta, 5/2 - and 9/2 - states of the 1/2(541) configuration have been identified. The core-quasiproton interaction has to be taken into account in order to explain the two-nucleon transfer intensities in the 181 Ta(p,t) 179 Ta reaction. A level scheme has been proposed for 180 Ta for the first time. Especially the ground state is identified with the (1 + ,1) level of the [7/2 + (404)sub(p), 9/2 + (624)sub(n)] configuration and spin (9 - ,9) of the configuration [9/2 - (514)sub(p), 9/2 + (624)sub(n)] has been assigned to the long-lived isomer. From the observed configurations in 180 Ta, the matrix elements of the effective residual interaction vsub(np) have been deduced and compared to theoretical predictions [fr

  7. Synthesis of Ni3Ta, Ni2Ta and NiTa by high-energy ball milling and subsequent heat treatment

    International Nuclear Information System (INIS)

    Benites, H.S.N.; Silva, B.P da; Ramos, A.S.; Silva, A.A.A.P.; Coelho, G.C.; Lima, B.B. de

    2014-01-01

    The tantalum has relevance for the development of multicomponent Ni-based superalloys which are hardened by solid solution and precipitation mechanisms. Master alloys are normally used in the production step in order to produce refractory metals and alloys. The present work reports on the synthesis of Ni_3Ta, Ni_2Ta and NiTa by high-energy ball milling and subsequent heat treatment. The elemental Ni-25Ta, Ni-33Ta and Ni-50Ta (at.-%) powder mixtures were ball milled under Ar atmosphere using stainless steel balls and vials, 300 rpm and a ball-to-powder weight ratio of 10:1. Following, the as-milled samples were uniaxially compacted and heat-treated at 1100 deg C for 4h under Ar atmosphere. The characterization of as-milled and heat-treated samples was conducted by means of X-ray diffraction, scanning electron microscopy, and energy dispersive spectrometry. A large amount of Ni_3Ta, Ni_2Ta and NiTa was formed in the mechanically alloyed heat-treated Ni-25Ta, Ni-33Ta and Ni-50Ta alloys. (author)

  8. Stoichiometry behavior of TaN, TaCN and TaC thin films produced by magnetron sputtering

    International Nuclear Information System (INIS)

    Vargas, M.; Castillo, H.A.; Restrepo-Parra, E.; De La Cruz, W.

    2013-01-01

    Thin films were synthesized in a magnetron sputtering system using a target of Ta with 99.99% purity and silicon substrates (1 1 1). The gases used for the film growth were (Ar + N 2 ), (Ar + CH 4 + N 2 ) and (Ar + CH 4 ) mixtures for TaN, TaCN and TaC, respectively. The substrate temperature increased from room temperature to 500 °C. The chemical composition and bonding configuration were examined using X-ray photoelectron spectroscopy (XPS), revealing Ta-N, Ta-C-N, Ta-C and C-C bonds. Moreover, the crystallographic structure was analyzed using X-ray diffraction (XRD), indicating the presence of (1 1 1) and (2 0 0) planes belonging to a face-centered cubic structure. The stoichiometry variation dependence on the CH 4 and N 2 flow was analyzed, and the influence of the substrate temperature on the coatings was investigated. Finally, scanning electron microscopy (SEM) was used to determine the evolution on the grain formation in the coatings as the substrate temperature increased.

  9. Stoichiometry behavior of TaN, TaCN and TaC thin films produced by magnetron sputtering

    Energy Technology Data Exchange (ETDEWEB)

    Vargas, M. [Centro de Nanociencia y Nanotecnología, Universidad Nacional Autónoma de México, A.P. 2681, C.P. 22860, Ensenada, B.C. (Mexico); Castillo, H.A. [Centro de Enseñanza Técnica y Superior, CETYS Universidad, Campus Tijuana, Tijuana, B.C. (Mexico); Restrepo-Parra, E., E-mail: erestrepopa@unal.edu.co [Universidad Nacional de Colombia Sede Medellín Colombia, Facultad de Minas, Manizales (Colombia); De La Cruz, W. [Centro de Nanociencia y Nanotecnología, Universidad Nacional Autónoma de México, A.P. 2681, C.P. 22860, Ensenada, B.C. (Mexico)

    2013-08-15

    Thin films were synthesized in a magnetron sputtering system using a target of Ta with 99.99% purity and silicon substrates (1 1 1). The gases used for the film growth were (Ar + N{sub 2}), (Ar + CH{sub 4} + N{sub 2}) and (Ar + CH{sub 4}) mixtures for TaN, TaCN and TaC, respectively. The substrate temperature increased from room temperature to 500 °C. The chemical composition and bonding configuration were examined using X-ray photoelectron spectroscopy (XPS), revealing Ta-N, Ta-C-N, Ta-C and C-C bonds. Moreover, the crystallographic structure was analyzed using X-ray diffraction (XRD), indicating the presence of (1 1 1) and (2 0 0) planes belonging to a face-centered cubic structure. The stoichiometry variation dependence on the CH{sub 4} and N{sub 2} flow was analyzed, and the influence of the substrate temperature on the coatings was investigated. Finally, scanning electron microscopy (SEM) was used to determine the evolution on the grain formation in the coatings as the substrate temperature increased.

  10. TaEDS1 genes positively regulate resistance to powdery mildew in wheat.

    Science.gov (United States)

    Chen, Guiping; Wei, Bo; Li, Guoliang; Gong, Caiyan; Fan, Renchun; Zhang, Xiangqi

    2018-04-01

    Three EDS1 genes were cloned from common wheat and were demonstrated to positively regulate resistance to powdery mildew in wheat. The EDS1 proteins play important roles in plant basal resistance and TIR-NB-LRR protein-triggered resistance in dicots. Until now, there have been very few studies on EDS1 in monocots, and none in wheat. Here, we report on three common wheat orthologous genes of EDS1 family (TaEDS1-5A, 5B and 5D) and their function in powdery mildew resistance. Comparisons of these genes with their orthologs in diploid ancestors revealed that EDS1 is a conserved gene family in Triticeae. The cDNA sequence similarity among the three TaEDS1 genes was greater than 96.5%, and they shared sequence similarities of more than 99.6% with the respective orthologs from diploid ancestors. The phylogenetic analysis revealed that the EDS1 family originated prior to the differentiation of monocots and dicots, and EDS1 members have since undergone clear structural differentiation. The transcriptional levels of TaEDS1 genes in the leaves were obviously higher than those of the other organs, and they were induced by Blumeria graminis f. sp. tritici (Bgt) infection and salicylic acid (SA) treatment. The BSMV-VIGS experiments indicated that knock-down the transcriptional levels of the TaEDS1 genes in a powdery mildew-resistant variety of common wheat compromised resistance. Contrarily, transient overexpression of TaEDS1 genes in a susceptible common wheat variety significantly reduced the haustorium index and attenuated the growth of Bgt. Furthermore, the expression of TaEDS1 genes in the Arabidopsis mutant eds1-1 complemented its susceptible phenotype to powdery mildew. The above evidences strongly suggest that TaEDS1 acts as a positive regulator and confers resistance against powdery mildew in common wheat.

  11. Method of quantitative x-ray diffractometric analysis of Ta-Ta2C system

    International Nuclear Information System (INIS)

    Gavrish, A.A.; Glazunov, M.P.; Korolev, Yu.M.; Spitsyn, V.I.; Fedoseev, G.K.

    1976-01-01

    The syste86 Ta-Ta 2 C has beemonsidered because of specific features of diffraction patterns of the components, namely, overlapping of the most intensive reflexes of both phases. The method of standard binary system has been used for quantitative analysis. Because of overlapping of the intensive reflexes dsub(1/01)=2.36(Ta 2 C) and dsub(110)=2.33(Ta), the other, most intensive, reflexes have been used for quantitative determination of Ta 2 C and Ta: dsub(103)=1.404 A for tantalum subcarbide and dsub(211)=1.35A for tantalum. Besides, the TaTa 2 C phases have been determined quantitatively with the use of another pair of reflexes: dsub(102)=1.82 A for Ta 2 C and dsub(200)=1.65 A for tantalum. The agreement between the results obtained while performing the quantitative phase analysis is good. To increase reliability and accuracy of the quantitative determination of Ta and Ta 2 C, it is expedient to carry out the analysis with the use of two above-mentioned pairs of reflexes located in different regions of the diffraction spectrum. Thus, the procedure of quantitative analysis of Ta and Ta 2 C in different ratios has been developed taking into account the specific features of the diffraction patterns of these components as well as the ability of Ta 2 C to texture in the process of preparation

  12. Effect of Ta content on martensitic transformation behavior of RuTa ultrahigh temperature shape memory alloys

    International Nuclear Information System (INIS)

    He Zhirong; Zhou Jingen; Furuya, Y.

    2003-01-01

    Effects of Ta content on martensitic transformation (MT) behavior of Ru 100-x Ta x (x=46-54 at.%) alloys have been investigated by differential scanning calorimetry, dilatometry, X-ray diffraction and optical microscopy. Ta content significantly affects the MT behavior of RuTa alloys. The one-stage reservible MT occurs in Ta-poor RuTa alloys with Ta content less than 49 at.%. The two-stage reservible MT takes place in near-equiatomic RuTa alloys. No reservible MT is observed in Ta-rich alloys with Ta content more then 52 at.% Ta. The MT temperatures and hysteresis of RuTa alloys decrease with increasing Ta content. The aged and thermal cycled processes are nearly no effect on the MT behavior of these alloys. The deforming way of RuTa alloys is twinning. The Ru 50 Ta 50 alloy is of the most excellent MT behavior among these RuTa alloys

  13. Investigation of TaC–TaB2 ceramic composites

    Indian Academy of Sciences (India)

    ture and the mechanical properties of the composites were investigated. The results .... 300 nm. Jingangzuan in the TaC/TaB2 composites SPS for 10 min at different temperatures are .... [1] Liu L, Yea F, Hea X and Zhoua Y 2011 Mater. Chem.

  14. 75 FR 43556 - TA-W-73,381, MT Rail Link, Inc., Missoula, MT; TA-W-73,381A, Billings, MT; TA-W-73,381B, Laurel...

    Science.gov (United States)

    2010-07-26

    ... DEPARTMENT OF LABOR Employment and Training Administration TA-W-73,381, MT Rail Link, Inc., Missoula, MT; TA-W-73,381A, Billings, MT; TA-W-73,381B, Laurel, MT; TA-W-73,381C, Livingston, MT; TA-W-73... Helena, Montana. The amended notice applicable to TA-W-73,381 is hereby issued as follows: All workers of...

  15. High-pressure phases of Weyl semimetals NbP, NbAs, TaP, and TaAs

    Science.gov (United States)

    Guo, ZhaoPeng; Lu, PengChao; Chen, Tong; Wu, JueFei; Sun, Jian; Xing, DingYu

    2018-03-01

    In this study, we used the crystal structure search method and first-principles calculations to systematically explore the highpressure phase diagrams of the TaAs family (NbP, NbAs, TaP, and TaAs). Our calculation results show that NbAs and TaAs have similar phase diagrams, the same structural phase transition sequence I41 md→ P6¯ m2→ P21/ c→ Pm3¯ m, and slightly different transition pressures. The phase transition sequence of NbP and TaP differs somewhat from that of NbAs and TaAs, in which new structures emerge, such as the Cmcm structure in NbP and the Pmmn structure in TaP. Interestingly, we found that in the electronic structure of the high-pressure phase P6¯ m2-NbAs, there are coexistingWeyl points and triple degenerate points, similar to those found in high-pressure P6¯ m2-TaAs.

  16. Oxidative addition of diphenyl disulfide across a Ta=Ta bond. Preparation and characterization of [TaCl3(Me2S)]2(μ-SPh)2

    International Nuclear Information System (INIS)

    Campbell, G.C.; Canich, J.A.M; Cotton, F.A.; Duraj, S.A.; Haw, J.F.

    1986-01-01

    The tantalum complex (SMe 2 )Cl 2 Ta(μ-Cl) 2 (μ-SMe 2 )TaCl 2 (SMe 2 ), possessing a sigma 2 π 2 Ta=Ta double bond, reacts readily with PhSSPh to give (SMe 2 )Cl 3 Ta(μ-SPh) 2 TaCl 2 (SMe 2 ). In this reaction, the starting material loses the bridging SMe 2 ligand and two chloride bridges are broken while only two new SPh bridges are formed in the final product. This oxidative-addition reaction of the S-S single bond to the Ta=Ta double bond converts the face-sharing bioctahedron structure of the starting compound to an edge-sharing bioctahedron structure in the final dimer, with concomitant change of the oxidation state of tantalum from III to IV. The product is the first example of a d 1 -d 1 ditantalum thiolate-bridged dimer. Important structural data for (SMe 2 )Cl 3 Ta(μ-SPh) 2 TaCl 3 (SMe 2 ), which has an inversion center, are determined. The new compound crystallizes in the monoclinic space group C2/c with a = 17.934 (5) A, b = 12.445 (4) A, c = 11.705 (4) A, β = 92.50 (3) 0 , V = 2610 (2) A 3 , and Z = 4. Solid-state 13 C NMR spectroscopy with cross polarization and magic-angle spinning (CP/MAS) at 28 and -103 0 C provides evidence that this compound is diamagnetic. 12 references, 3 figures, 4 tables

  17. Web TA Production (WebTA)

    Data.gov (United States)

    US Agency for International Development — WebTA is a web-based time and attendance system that supports USAID payroll administration functions, and is designed to capture hours worked, leave used and...

  18. Density of salt melts containing KF, KCl, K2TaF7 and Ta2O5

    International Nuclear Information System (INIS)

    Agulyanskij, A.I.; Stangrit, P.T.; Konstantinov, V.I.

    1978-01-01

    The results of density measurements by hydrostatic weighing are given for molten K 2 TaF 7 - KF, K 2 TaF 7 -KCL, K 2 TaF 7 - KF - KCl and K 2 TaF 7 - KF - KCl - Ta 2 O 5 mixtures depending on their temperature and composition. The density of the last two systems was measured at compositions close to those of commercial electrolytes. The obtained specific volume - composition dependencies show that no interaction is taking place in the mixtures studied. It is, therefore, believed that, in the K 2 TaF 7 - KF melt, tantalum is mainly present as a complex TaF 7 2- ion, and, in the K 2 TaF 7 - KCl mlt, a certain amount of TaF 6 - ions may be formed along with TaF 7 2-

  19. 78 FR 28627 - TA-W-80,340; TA-W-80,340A; TA-W-80,340B

    Science.gov (United States)

    2013-05-15

    ...] Bush Industries, Inc., Mason Drive Facility, Including On-Site Leased Workers From Morris Security...., Mason Drive Facility, Jamestown, New York (TA-W-80,340) and Bush Industries, Inc., Allen Street Facility... applicable to TA-W-80,340 is hereby issued as follows: All workers of Bush Industries, Inc., Mason Drive...

  20. Ta thickness-dependent perpendicular magnetic anisotropy features in Ta/CoFeB/MgO/W free layer stacks

    Energy Technology Data Exchange (ETDEWEB)

    Yang, SeungMo; Lee, JaBin; An, GwangGuk [Novel Functional Materials and Devices Lab, The Research Institute for Natural Science, Department of Physics, Hanyang University, Seoul 133-791 (Korea, Republic of); Kim, JaeHong [Division of Nano-Scale Semiconductor Engineering, Hanyang University, Seoul 133-791 (Korea, Republic of); Chung, WooSeong [Nano Quantum Electronics Lab, Department of Electronics and Computer Engineering, Hanyang University, Seoul 133-791 (Korea, Republic of); Hong, JinPyo, E-mail: jphong@hanyang.ac.kr [Novel Functional Materials and Devices Lab, The Research Institute for Natural Science, Department of Physics, Hanyang University, Seoul 133-791 (Korea, Republic of); Division of Nano-Scale Semiconductor Engineering, Hanyang University, Seoul 133-791 (Korea, Republic of)

    2015-07-31

    We describe Ta underlayer thickness influence on thermal stability of perpendicular magnetic anisotropy in Ta/CoFeB/MgO/W stacks. It is believed that thermal stability based on Ta underlay is associated with thermally-activated Ta atom diffusion during annealing. The difference in Ta thickness-dependent diffusion behaviors was confirmed with X-ray photoelectron spectroscopy analysis. Along with a feasible Ta thickness model, our observations suggest that an appropriate seed layer choice is needed for high temperature annealing stability, a critical issue in the memory industry. - Highlights: • We observed changes in the diffusion behavior with regard to Ta seed layer thickness. • It was observed that a thinner Ta seed layer induced more annealing-stable features. • However, ultra-thin (0.75 nm) Ta shows unstable characteristics about the annealing process. • It was possibly due to a rugged interface of the Ta layer by the island growth process.

  1. EUSO-TA prototype telescope

    Energy Technology Data Exchange (ETDEWEB)

    Bisconti, Francesca, E-mail: francesca.bisconti@kit.edu

    2016-07-11

    EUSO-TA is one of the prototypes developed for the JEM-EUSO project, a space-based large field-of-view telescope to observe the fluorescence light emitted by cosmic ray air showers in the atmosphere. EUSO-TA is a ground-based prototype located at the Telescope Array (TA) site in Utah, USA, where an Electron Light Source and a Central Laser Facility are installed. The purpose of the EUSO-TA project is to calibrate the prototype with the TA fluorescence detector in presence of well-known light sources and cosmic ray air showers. In 2015, the detector started the first measurements and tests using the mentioned light sources have been performed successfully. A first cosmic ray candidate has been observed, as well as stars of different magnitude and color index. Since Silicon Photo-Multipliers (SiPMs) are very promising for fluorescence telescopes of next generation, they are under consideration for the realization of a new prototype of EUSO Photo Detector Module (PDM). The response of this sensor type is under investigation through simulations and laboratory experimentation.

  2. EUSO-TA prototype telescope

    Science.gov (United States)

    Bisconti, Francesca; JEM-EUSO Collaboration

    2016-07-01

    EUSO-TA is one of the prototypes developed for the JEM-EUSO project, a space-based large field-of-view telescope to observe the fluorescence light emitted by cosmic ray air showers in the atmosphere. EUSO-TA is a ground-based prototype located at the Telescope Array (TA) site in Utah, USA, where an Electron Light Source and a Central Laser Facility are installed. The purpose of the EUSO-TA project is to calibrate the prototype with the TA fluorescence detector in presence of well-known light sources and cosmic ray air showers. In 2015, the detector started the first measurements and tests using the mentioned light sources have been performed successfully. A first cosmic ray candidate has been observed, as well as stars of different magnitude and color index. Since Silicon Photo-Multipliers (SiPMs) are very promising for fluorescence telescopes of next generation, they are under consideration for the realization of a new prototype of EUSO Photo Detector Module (PDM). The response of this sensor type is under investigation through simulations and laboratory experimentation.

  3. Electrodeposition of Al-Ta alloys in NaCl-KCl-AlCl{sub 3} molten salt containing TaCl{sub 5}

    Energy Technology Data Exchange (ETDEWEB)

    Sato, Kazuki; Matsushima, Hisayoshi; Ueda, Mikito, E-mail: mikito@eng.hokudai.ac.jp

    2016-12-01

    Highlights: • Electrodeposition of Al-Ta alloys in an AlCl{sub 3}-NaCl-KCl-TaCl{sub 5} melt was carried out. • We were obtained 72 at% Ta-Al alloy at 0.3 V. • Amorphous Ta-Al was formed in high Ta concentration. - Abstract: To form Al-Ta alloys for high temperature oxidation resistance components, molten salt electrolysis was carried out in an AlCl{sub 3}-NaCl-KCl melt containing TaCl{sub 5} at 423 K. The voltammogram showed two cathodic waves at 0.45 V and 0.7 V vs. Al/Al(III), which may correspond to reduction from Ta(V) to Ta(III) and from Ta(III) to tantalum metal, respectively. Electrodeposits of Al and Ta were obtained in the range from −0.05 to 0.3 V and the highest concentration of Ta in the electrodeposit was 72 at% at 0.3 V. With increasing Ta content in the alloy, the morphology of the electrodeposits became powdery and the particle size smaller.

  4. Copper diffusion in TaN-based thin layers

    Energy Technology Data Exchange (ETDEWEB)

    Nazon, J. [Universite Montpellier II, Institut Charles Gerhardt, UMR 5253 CNRS-UM2-ENSCM-UM1, cc 1504, 34095 Montpellier Cedex 5 (France); Fraisse, B. [Laboratoire Structure, Proprietes et Modelisation des Solides (UMR 8580), Ecole Centrale de Paris, Grande Voie des Vignes, 92295 Chatenay-Malabry Cedex (France); Sarradin, J. [Universite Montpellier II, Institut Charles Gerhardt, UMR 5253 CNRS-UM2-ENSCM-UM1, cc 1504, 34095 Montpellier Cedex 5 (France); Fries, S.G. [SGF Scientific Consultancy, Arndt str.9, D-52064 Aachen (Germany); Tedenac, J.C. [Universite Montpellier II, Institut Charles Gerhardt, UMR 5253 CNRS-UM2-ENSCM-UM1, cc 1504, 34095 Montpellier Cedex 5 (France); Frety, N. [Universite Montpellier II, Institut Charles Gerhardt, UMR 5253 CNRS-UM2-ENSCM-UM1, cc 1504, 34095 Montpellier Cedex 5 (France)], E-mail: Nicole.Frety@univ-montp2.fr

    2008-07-15

    The diffusion of Cu through TaN-based thin layers into a Si substrate has been studied. The barrier efficiency of TaN/Ta/TaN multilayers of 150 nm in thickness has been investigated and is compared with that of TaN single layers. Thermal stabilities of these TaN-based thin layers against Cu diffusion were determined from in situ X-ray diffraction experiments, conducted in the temperature range of 773-973 K. The TaN/Ta/TaN barrier appeared to be more efficient in preventing Cu diffusion than the TaN single layer.

  5. Structure and physical properties of Cr_5B_3-type Ta_5Si_3 and Ta_5Ge_3

    International Nuclear Information System (INIS)

    Yuan, Fang; Forbes, Scott; Ramachandran, Krishna Kumar; Mozharivskyj, Yurij

    2015-01-01

    The Cr_5B_3-type Ta_5Si_3 phase was prepared by arc-melting, while the Cr_5B_3-type Ta_5Ge_3 one was synthesized through sintering at 1000 °C. X-ray single crystal diffraction was employed to elucidate their structure. According to the magnetization measurements, both Ta_5Si_3 and Ta_5Ge_3 are Pauli paramagnets, with Ta_5Ge_3 showing a Curie-Weiss-like paramagnetic behavior at low temperatures likely due to presence of paramagnetic impurity. Both Ta_5Si_3 and Ta_5Ge_3 display a very low electrical resistivity from 2 to 300 K. The resistivity is constant below 20 K, but displays a positive temperature coefficient above 20 K. Electronic structure calculations with the TB-LMTO-ASA method support the metallic character of the two phases and suggest that the bonding is optimized in both phases. - Highlights: • Synthesis of Cr_5B_3-type Ta_5Si_3 and Ta_5Ge_3 phases with high purity by arc-melting and sintering, respectively. • Magnetization data and electrical resistivity of the Cr_5B_3-type Ta_5Si_3 and Ta_5Ge_3 phases. • Crystal and electronic structure analysis for Ta_5Si_3 and Ta_5Ge_3 phase by X-ray diffraction and TB-LMTO-ASA calculations.

  6. fs - kes ta on ja kust ta tuleb : [luuletused] / [Mesikepp, Indrek] fs

    Index Scriptorium Estoniae

    fs, pseud., 1971-

    2004-01-01

    Sisu: fs - kes ta on ja kust ta tuleb ; "töötasin arhiivis..." ; mustad puud mustas vees ; "on päev. on kylm. on öö..." ; "tead ju kyll..." ; "päiksest paistes päevad..." ; "mida sa teed kui on öö..."

  7. Facile and efficient synthesis of the surface tantalum hydride (≡SiO)2TaIIIH and tris-siloxy tantalum (≡SiO)3TaIII starting from novel tantalum surface species (≡SiO)TaMe4 and (≡SiO)2TaMe 3

    KAUST Repository

    Chen, Yin

    2014-03-10

    By grafting of TaMe5 (1) on the surface of silica partially dehydroxylated at 500 C (silica500), a mixture of (≡SiO)TaMe4 (2a; major, 65 ± 5%) and (≡SiO) 2TaMe3 (2b; minor, 35 ± 5%) was produced, which has been characterized by microanalysis, IR, and SS NMR (1H, 13C, 1H-13C HETCOR, proton double and triple quantum). After grafting, these surface organometallic compounds are more stable than the precursor TaMe5. Treatment of 2a,b with water and H 2 resulted in the formation of methane in amount of 3.6 ± 0.2 and 3.4 ± 0.2 mol/grafted Ta, respectively. 2a,b react with H2 (800 mbar) to form (≡SiO)2TaH. After (≡SiO) 2TaH was heated to 500 C under hydrogen or vacuum, [(≡SiO) 3Ta][≡SiH] was produced, and the structure was confirmed by IR, NMR, and EXAFS. Considering the difficulty of the previous preparation method, these syntheses represent a facile and convenient way to prepare tantalum surface species (≡SiO)2TaH and (≡SiO)3Ta via the intermediate of the new surface organometallic precursors: (≡SiO)TaMe4/(≡SiO)2TaMe3. (≡SiO)2TaH and (≡SiO)3Ta exhibit equal reactivities in alkane metathesis and ethylene polymerization in comparison to those in previous reports. © 2014 American Chemical Society.

  8. Facile and efficient synthesis of the surface tantalum hydride (≡SiO)2TaIIIH and tris-siloxy tantalum (≡SiO)3TaIII starting from novel tantalum surface species (≡SiO)TaMe4 and (≡SiO)2TaMe 3

    KAUST Repository

    Chen, Yin; Ould-Chikh, Samy; Abou-Hamad, Edy; Callens, Emmanuel; Mohandas, Janet Chakkamadathil; Khalid, Syed M.; Basset, Jean-Marie

    2014-01-01

    By grafting of TaMe5 (1) on the surface of silica partially dehydroxylated at 500 C (silica500), a mixture of (≡SiO)TaMe4 (2a; major, 65 ± 5%) and (≡SiO) 2TaMe3 (2b; minor, 35 ± 5%) was produced, which has been characterized by microanalysis, IR, and SS NMR (1H, 13C, 1H-13C HETCOR, proton double and triple quantum). After grafting, these surface organometallic compounds are more stable than the precursor TaMe5. Treatment of 2a,b with water and H 2 resulted in the formation of methane in amount of 3.6 ± 0.2 and 3.4 ± 0.2 mol/grafted Ta, respectively. 2a,b react with H2 (800 mbar) to form (≡SiO)2TaH. After (≡SiO) 2TaH was heated to 500 C under hydrogen or vacuum, [(≡SiO) 3Ta][≡SiH] was produced, and the structure was confirmed by IR, NMR, and EXAFS. Considering the difficulty of the previous preparation method, these syntheses represent a facile and convenient way to prepare tantalum surface species (≡SiO)2TaH and (≡SiO)3Ta via the intermediate of the new surface organometallic precursors: (≡SiO)TaMe4/(≡SiO)2TaMe3. (≡SiO)2TaH and (≡SiO)3Ta exhibit equal reactivities in alkane metathesis and ethylene polymerization in comparison to those in previous reports. © 2014 American Chemical Society.

  9. EUSO-TA data and simulations

    Energy Technology Data Exchange (ETDEWEB)

    Bisconti, Francesca [Institut fuer Kernphysik (IKP), Karlsruher Institut fuer Technologie (KIT) (Germany); Collaboration: JEM-EUSO-Collaboration

    2016-07-01

    EUSO-TA is one of the fluorescence cosmic ray detector prototypes developed by the JEM-EUSO Collaboration. The prototype has two 1 m diameter Fresnel lenses and one photo detector module (PDM) as focal surface. The PDM consists of 36 multi-anode photomultiplier tubes from Hamamatsu. The prototype has been designed to get information about the calibration of the Fresnel lense system and the PDM, basic parts of the main space-based fluorescence detector under development. EUSO-TA is located at the Black Rock Mesa site of the Telescope Array project (Utah-USA) and works in parallel with the TA fluorescence detectors since February 2015. During its campaigns, EUSO-TA detects cosmic ray events, as well as the pulsed laser from the Central Laser Facility, necessary for the detector calibration. Also planes and stars signatures are well visible in the data, although out of the scientific purpose. The analysis of EUSO-TA data and the comparison of data with simulations will be shown.

  10. Direct observation of effective temperature of Ta atom in layer compound TaS2 by neutron resonance absorption spectrometer

    International Nuclear Information System (INIS)

    Tokuda, Koji; Kamiyama, Takashi; Kiyanagi, Yoshiaki; Moreh, R.; Ikeda, Susumu

    2001-01-01

    A neutron resonance absorption spectrometer, DOG has been installed at KENS, High Energy Accelerator Research Organization Neutron Source, which enables us to investigate the motions of a particular element by analyzing the line width of resonance absorption spectrum. We measured the temperature dependence of the effective temperature of Ta motion in TaS 2 as well as in Ta metal using DOG. The effective temperatures extracted from the observed absorption spectrum agree well with the calculated values from the phonon density of states of Ta metal over a wide temperature range of 10 to 300 K. We also succeeded in measuring both the angular dependence and the temperature dependence of effective temperatures of Ta in a layer compound TaS 2 . Based on the temperature dependence of the effective temperature, the partial phonon density of states of Ta in TaS 2 was discussed. (author)

  11. Modelling the mechanical behaviour of heterogeneous Ta/TA6V welded joints: behaviour and failure criteria; Modelisation du comportement mecanique des liaisons soudees heterogenes Ta/TA6V: comportement et critere de rupture

    Energy Technology Data Exchange (ETDEWEB)

    Paris, Th

    2008-12-15

    As laser welding of two different materials (heterogeneous welding) leads to a joint having a characteristic size close to the millimetre, i.e. much smaller than that of a structure, and as such a junction displays completely different mechanical properties because of the metallurgical transformations induced by intense thermal loading, the aim of this research thesis is to develop a behaviour model, flexible and robust enough, to represent all together the mechanical behaviours of the Ta, the TA6V and the melted zone. This model must be able to take plasticity and visco-plasticity into account, and also to provide a failure criterion through damage mechanics and its coupling with the behaviour. The author first reports the experimental characterization of the base materials (Ta and TA6V) by using tensile tests under different strain rates and different directions, relaxation tests and fatigue shear tests. He also characterizes the melted zone by describing the influence of a thermal treatment (induced by welding) on the formation of the melted zone, and by using different tests: four point bending on notched specimens, nano-indentation test, and longitudinal tensile test. In a second part, the author develops the model within the framework of continuum thermodynamics, and explores the numerical issues. The last part deals with the validation of the model for the concerned materials (Ta and TA6V) and melted zone.

  12. Ultrathin TaOx film based photovoltaic device

    International Nuclear Information System (INIS)

    Tyagi, Pawan

    2011-01-01

    Application of the economical metal oxide thin-film photovoltaic devices is hindered by the poor energy efficiency. This paper investigates the photovoltaic effect with an ultrathin tantalum oxide (TaOx) tunnel barrier, formed by the plasma oxidation of a pre-deposited tantalum (Ta) film. These ∼ 3 nm TaOx tunnel barriers showed approximately 160 mV open circuit voltage and 3-5% energy efficiency, for varying light intensity. The ultrathin TaOx (∼ 3 nm) could absorb approximately 12% of the incident light radiation in 400-1000 nm wavelength range; this strong light absorbing capability was found to be associated with the dramatically large extinction coefficient. Spectroscopic ellipsometry revealed that the extinction coefficient of 3 nm TaOx was ∼ 0.2, two orders higher than that of tantalum penta oxide (Ta 2 O 5 ). Interestingly, refractive index of this 3 nm thick TaOx was comparable with that of stochiometeric Ta 2 O 5 . However, heating and prolonged high-intensity light exposure deteriorated the photovoltaic effect in TaOx junctions. This study provides the basis to explore the photovoltaic effect in a highly economical and easily processable ultrathin metal oxide tunnel barrier or analogous systems.

  13. Tribological properties of self-lubricating Ta-Cu films

    Science.gov (United States)

    Qin, Wen; Fu, Licai; Zhu, Jiajun; Yang, Wulin; Li, Deyi; Zhou, Lingping

    2018-03-01

    In this paper, Ta and TaCu films were deposited by using magnetron sputtering, and the tribological properties of the films against Si3N4 balls were investigated under the loads of 2 N and 5 N. The average grain sizes of both films are below 25 nm. Ta and TaCu films have approximate hardness. While the wear rate of TaCu film is much smaller than that of Ta film. Post-wear testing XRD, Raman and XPS revealed the formation of tantalum oxide on the worn surface of both Ta and TaCu films. Tantalum oxidation is effectively lubricating to reduce friction coefficient. So the friction coefficient of both Ta and TaCu film is about 0.45 under different applied loads. Meanwhile, the addition of Cu could increase the toughness of the film, and avoid the generation of wear debris, resulting in a significant increase in wear resistance.

  14. Sorption and desorption of cesium and strontium on TA-2 and TA-41 soils and sediments

    International Nuclear Information System (INIS)

    Kung, K. Stephen; Li, Benjamin W.; Longmire, P.A.; Fowler, M.M.

    1996-04-01

    Current environmental monitoring has detected radioactive contaminants in alluvial groundwater, soils, and sediments in the TA-2 and TA-41 areas along the north central edge of Los Alamos National Laboratory. Because of this contamination, this study was initiated. The objective of this study is to quantify the sorptivity of cesium and strontium onto TA-2 and TA-41 site specific soil samples under a controlled environment in the laboratory. The purposes of this work are to determine cesium and strontium sorption coefficient for these sit specific soils and to evaluate the potential transport of cesium and strontium. Based on this information, a risk assessment and remediation strategy can be developed

  15. Thermodynamic description of the Ta-W-Zr system

    International Nuclear Information System (INIS)

    Guo, Cuiping; Li, Changrong; Du, Zhenmin; Shang, Shunli

    2014-01-01

    The Ta-W, W-Zr and Ta-W-Zr systems are critically reviewed and modeled using the CALPHAD technique. The enthalpy of formation of the stoichiometric compound W 2 Zr in the W-Zr system is predicted from first-principles calculations. The solution phases (liquid, bcc and hcp) are modeled by the substitutional solution model. The compound W 2 Zr is treated with the formula (Ta,W) 2 Zr in the Ta-W-Zr system because of a significant solid solubility of Ta in W 2 Zr. All experimental data, including the Gibbs energy of formation, enthalpy of formation, activity of Ta and W of bcc phase at 1 200 K, Ta-W and W-Zr phase diagrams, and three isothermal sections of the Ta-W-Zr system at 1 073, 1 098, and 1 873 K, are reproduced in the present work. A set of self-consistent thermodynamic parameters of the Ta-W-Zr system is obtained.

  16. Electric-field gradients at Ta donor impurities in Cr2O3(Ta) semiconductor

    International Nuclear Information System (INIS)

    Darriba, G.N.; Errico, L.A.; Munoz, E.L; Richard, D.; Eversheim, P.D.; Renteria, M.

    2009-01-01

    We report perturbed-angular-correlation (PAC) experiments on 181 Hf(→ 181 Ta)-implanted corundum Cr 2 O 3 powder samples in order to determine the magnitude and symmetry of the electric-field gradient (EFG) tensor at Ta donor impurity sites of this semiconductor. These results are analyzed in the framework of ab initio full-potential augmented-plane wave plus local orbitals (FP-APW+lo) calculations. The results are also compared with EFG results coming from PAC experiments in isomorphous α-Al 2 O 3 and α-Fe 2 O 3 doped with 111 In→ 111 Cd and 181 Hf→ 181 Ta tracers. This combined analysis enables us to quantify the magnitude of the lattice relaxations induced by the presence of the impurity and to determine the charge state of the impurity donor level introduced by Ta in the band gap of the semiconductor.

  17. Combined experimental and theoretical assessments of the lattice dynamics and optoelectronics of TaON and Ta{sub 3}N{sub 5}

    Energy Technology Data Exchange (ETDEWEB)

    Nurlaela, Ela; Harb, Moussab [Division of Physical Sciences and Engineering, KAUST Catalysis Center (KCC), King Abdullah University of Science and Technology (KAUST), 4700 KAUST, Thuwal 23955-6900 Saudi Arabia (Saudi Arabia); Gobbo, Silvano del [Solar and Photovoltaic Engineering Center, King Abdullah University of Science and Technology (KAUST), Thuwal 23955-6900 (Saudi Arabia); Vashishta, Manish [Division of Physical Sciences and Engineering, KAUST Catalysis Center (KCC), King Abdullah University of Science and Technology (KAUST), 4700 KAUST, Thuwal 23955-6900 Saudi Arabia (Saudi Arabia); Takanabe, Kazuhiro, E-mail: kazuhiro.takanabe@kaust.edu.sa [Division of Physical Sciences and Engineering, KAUST Catalysis Center (KCC), King Abdullah University of Science and Technology (KAUST), 4700 KAUST, Thuwal 23955-6900 Saudi Arabia (Saudi Arabia)

    2015-09-15

    Presented herein is a detailed discussion of the properties of the lattice dynamic and optoelectronic properties of tantalum(V) oxynitride (TaON) and tantalum(V) nitride (Ta{sub 3}N{sub 5}), from experimental and theoretical standpoint. The active Raman and infra red (IR) frequencies of TaON and Ta{sub 3}N{sub 5} were measured using confocal Raman and Fourier Transform Infrared spectroscopies (FTIR) and calculated using the linear response method within the density functional perturbation theory (DFPT). The detailed study leads to an exhaustive description of the spectra, including the symmetry of the vibrational modes. Electronic structures of these materials were computed using DFT within the range-separated hybrid HSE06 exchange–correlation formalism. Electronic and ionic contributions to the dielectric constant tensors of these materials were obtained from DFPT within the linear response method using the PBE functional. Furthermore, effective mass of photogenerated holes and electrons at the band edges of these compounds were computed from the electronic band structure obtained at the DFT/HSE06 level of theory. The results suggest that anisotropic nature in TaON and Ta{sub 3}N{sub 5} is present in terms of dielectric constant and effective masses. - Graphical abstract: Detailed investigation has been conducted from combined experimental and theoretical approaches on Raman and IR spectroscopies, electronic structures, dielectric constants and effective masses of TaON and Ta{sub 3}N{sub 5}. - Highlights: • Crystal structures of TaON and Ta{sub 3}N{sub 5} are discussed based on XRD and DFT calculation. • Raman and IR spectra of TaON and Ta{sub 3}N{sub 5} materials are measured and computed by DFPT method. • Optoelectronic properties of TaON and Ta{sub 3}N{sub 5} are discussed. • Dielectric constant and effective masses of TaON and Ta{sub 3}N{sub 5} are calculated.

  18. New ternary tantalum borides containing boron dumbbells: Experimental and theoretical studies of Ta2OsB2 and TaRuB

    International Nuclear Information System (INIS)

    Mbarki, Mohammed; Touzani, Rachid St.; Rehorn, Christian W.G.; Gladisch, Fabian C.; Fokwa, Boniface P.T.

    2016-01-01

    The new ternary transition metal-rich borides Ta 2 OsB 2 and TaRuB have been successfully synthesized by arc-melting the elements in a water-cooled crucible under an argon atmosphere. The crystal structures of both compounds were solved by single-crystal X-ray diffraction and their metal compositions were confirmed by EDX analysis. It was found that Ta 2 OsB 2 and TaRuB crystallize in the tetragonal Nb 2 OsB 2 (space group P4/mnc, no. 128) and the orthorhombic NbRuB (space group Pmma, no. 51) structure types with lattice parameters a=5.878(2) Å, c=6.857(2) Å and a=10.806(2) Å, b=3.196(1) Å, c=6.312(2) Å, respectively. Furthermore, crystallographic, electronic and bonding characteristics have been studied by density functional theory (DFT). Electronic structure relaxation has confirmed the crystallographic parameters while COHP bonding analysis indicates that B 2 -dummbells are the strongest bonds in both compounds. Moreover, the formation of osmium dumbbells in Ta 2 OsB 2 through a Peierls distortion along the c-axis, is found to be the origin of superstructure formation. Magnetic susceptibility measurements reveal that the two phases are Pauli paramagnets, thus confirming the theoretical DOS prediction of metallic character. Also hints of superconductivity are found in the two phases, however lack of single phase samples has prevented confirmation. Furthermore, the thermodynamic stability of the two modifications of AMB (A=Nb, Ta; M =Ru, Os) are studied using DFT, as new possible phases containing either B 4 - or B 2 -units are predicted, the former being the most thermodynamically stable modification. - Graphical abstract: The two new ternary tantalum borides, Ta 2 OsB 2 and TaRuB, have been discovered. Their crystal structures contain boron dumbbells, which are the strongest bonds. Peirls distortion is found responsible for Os 2 -dumbbells formation in Ta 2 OsB 2 . Ta 2 OsB 2 and TaRuB are Pauli paramagnet and potential superconductors. - Highlights:

  19. Tuning the effective parameters in (Ta/Cu/[Ni/Co]x/Ta) multilayers with perpendicular magnetic anisotropy

    Science.gov (United States)

    Ayareh, Zohreh; Moradi, Mehrdad; Mahmoodi, Saman

    2018-06-01

    In this paper, we report perpendicular magnetic anisotropy (PMA) in a (Ta/Cu/[Ni/Co]x/Ta) multilayers structure. These typical structures usually include a multilayer of ferromagnetic and transition metal thin films. Usually, magnetic anisotropy is characterized by magnetization loops determined by magnetometer or magneto-optical Kerr effect (MOKE). The interface between ferromagnetic and metallic layers plays an important role in magnetic anisotropy evolution from out-of-plane to in-plane in (Ta/Cu/[Ni/Co]/Ta) structure. Obtained results from MOKE and magnetometry of these samples show that they have different easy axes due to change in thickness of Cu as spacer layer and difference in number of repetition of [Ni/Co] stacks.

  20. Ta penetration into template-type porous low-k material during atomic layer deposition of TaN

    International Nuclear Information System (INIS)

    Furuya, Akira; Ohtsuka, Nobuyuki; Misawa, Kaori; Shimada, Miyoko; Ogawa, Shinichi

    2005-01-01

    Ta penetration into a planar template-type porous low-k film during atomic layer deposition of TaN has been investigated by evaluating relations between Ta penetration and number of deposition cycles, exposure time of Ta precursor per deposition cycle, substrate temperature, and porosity of the porous low-k. The precursors were pentakisdimethylaminotantalum [PDMAT:Ta(N(CH 3 ) 2 ) 5 ] and NH 3 . The porous low-k was a methylsiloxane (MSX) whose pore size in the maximum distribution and porosity of the porous low-k were 0-1.9 nm and 0%-47%. Depth profile of the Ta penetration was measured by transmission electron microscopy and energy dispersive x-ray spectroscopy. The amount of penetrated and the penetration depth depended on the porosity. It was found that the precursors penetrate into the MSX film dominantly by gas phase diffusion through pores connecting from the surface to the inside. Increased surface area of the MSX film due to the pores results in a depletion of precursor at the wafer edge, and that this depletion causes the penetration characteristics at the edge of wafer differ from those at the center of the wafer. Moreover, the thickness required for the pore sealing by additive liner deposition is discussed

  1. Thin TaC layer produced by ion mixing

    DEFF Research Database (Denmark)

    Barna, Árpád; Kotis, László; Pécz, Béla

    2012-01-01

    in strongly asymmetric ion mixing; the carbon was readily transported to the Ta layer, while the reverse process was much weaker. Because of the asymmetrical transport the C/TaC interface remained sharp independently from the applied fluence. The carbon transported to the Ta layer formed Ta......Ion-beam mixing in C/Ta layered systems was investigated. C 8nm/Ta 12nm and C 20nm/Ta 19nm/C 20nm layer systems were irradiated by Ga+ ions of energy in the range of 2–30keV. In case of the 8nm and 20nm thick C cover layers applying 5–8keV and 20–30keV Ga+ ion energy, respectively resulted...

  2. Resonances in odd-odd 182Ta

    Directory of Open Access Journals (Sweden)

    Brits C.P.

    2017-01-01

    Full Text Available Enhanced γ-decay on the tail of the giant electric dipole resonance, such as the scissors or pygmy resonances, can have significant impact on (n,γ reaction rates. These rates are important input for modeling processes that take place in astrophysical environments and nuclear reactors. Recent results from the University of Oslo indicate the existence of a significant enhancement in the photon strength function for nuclei in the actinide region due to the scissors resonance. Further, the M1 strength distribution of the scissors resonances in rare earth nuclei has been studied extensively over the years. To investigate the evolution and persistence of the scissor resonance in other mass regions, an experiment was performed utilizing the NaI(Tl γ-ray detector array (CACTUS and silicon particle telescopes (SiRi at the University of Oslo Cyclotron laboratory. Particle-γ coincidences from the 181Ta(d,p182Ta and 181Ta(d,d'181Ta reactions were used to measure the nuclear level density and photon strength function of the well-deformed 181Ta and 182Ta systems, to investigate the existence of resonances below the neutron separation energy.

  3. Enhanced post-annealing stability of perpendicular Ta/CoFeB/Mg/MgO multilayers by inhibiting Ta diffusion

    Energy Technology Data Exchange (ETDEWEB)

    Li, Xu-Jing; Jiang, Shao-Long; Zhang, Jing-Yan; Liu, Qian-Qian; Liu, Yi-Wei; Zhao, Jian-Cheng [Department of Materials Physics and Chemistry, University of Science and Technology Beijing, Beijing 100083 (China); Wu, Zheng-Long [Analytical and Testing Center, Beijing Normal University, Beijing 100875 (China); Feng, Chun, E-mail: fengchun@ustb.edu.cn [Department of Materials Physics and Chemistry, University of Science and Technology Beijing, Beijing 100083 (China); Li, Ming-Hua [Department of Materials Physics and Chemistry, University of Science and Technology Beijing, Beijing 100083 (China); Yu, Guang-Hua, E-mail: ghyu@mater.ustb.edu.cn [Department of Materials Physics and Chemistry, University of Science and Technology Beijing, Beijing 100083 (China)

    2016-03-01

    Graphical abstract: To reveal the underlying mechanism of Mg influence on the enhanced post-annealing stability of perpendicular Ta/CoFeB/Mg/MgO multilayers, the X-ray photoelectron spectroscopy analysis have been performed. It is found that a certain amount of Mg interlayer at the CoFeB/MgO interface could prevent the Ta oxidation to some extent due to the oxygen deficit MgO{sub x} (x < 1), and consequently lower the diffusion motivation of Ta from the bottom layer to the CoFeB/MgO interfaces to some extent during the annealing process. The prevention of Ta diffusion realizes the effective hybridization of Fe and O at the CoFeB/MgO interface and maintains interfacial magnetic anisotropy (K{sub CoFeB/MgO}). As a result, the perpendicular magnetic anisotropy at high annealing temperatures was maintained. - Highlights: • High annealing stability of perpendicular Ta/CoFeB/Mg/MgO multilayers was realized. • X-ray photoelectron spectroscopy analysis has been performed to explore the reasons. • The prevention of Ta diffusion was realized by introducing Mg at the CoFeB/MgO interface. - Abstracts: To reveal the underlying mechanism of Mg influence on the enhanced post-annealing stability of perpendicular Ta/CoFeB/Mg/MgO multilayers, the X-ray photoelectron spectroscopy analysis has been performed. It is found that a certain amount of Mg interlayer at the CoFeB/MgO interface could prevent the Ta oxidation, and consequently lower the diffusion motivation of Ta from the bottom layer to the CoFeB/MgO interfaces to some extent in the annealing process. The prevention of Ta diffusion realizes the effective hybridization of Fe and O at the CoFeB/MgO interface and maintains interfacial magnetic anisotropy (KCoFeB/MgO). As a result, the perpendicular magnetic anisotropy at high annealing temperatures is maintained.

  4. Enhanced post-annealing stability of perpendicular Ta/CoFeB/Mg/MgO multilayers by inhibiting Ta diffusion

    International Nuclear Information System (INIS)

    Li, Xu-Jing; Jiang, Shao-Long; Zhang, Jing-Yan; Liu, Qian-Qian; Liu, Yi-Wei; Zhao, Jian-Cheng; Wu, Zheng-Long; Feng, Chun; Li, Ming-Hua; Yu, Guang-Hua

    2016-01-01

    Graphical abstract: To reveal the underlying mechanism of Mg influence on the enhanced post-annealing stability of perpendicular Ta/CoFeB/Mg/MgO multilayers, the X-ray photoelectron spectroscopy analysis have been performed. It is found that a certain amount of Mg interlayer at the CoFeB/MgO interface could prevent the Ta oxidation to some extent due to the oxygen deficit MgO_x (x < 1), and consequently lower the diffusion motivation of Ta from the bottom layer to the CoFeB/MgO interfaces to some extent during the annealing process. The prevention of Ta diffusion realizes the effective hybridization of Fe and O at the CoFeB/MgO interface and maintains interfacial magnetic anisotropy (K_C_o_F_e_B_/_M_g_O). As a result, the perpendicular magnetic anisotropy at high annealing temperatures was maintained. - Highlights: • High annealing stability of perpendicular Ta/CoFeB/Mg/MgO multilayers was realized. • X-ray photoelectron spectroscopy analysis has been performed to explore the reasons. • The prevention of Ta diffusion was realized by introducing Mg at the CoFeB/MgO interface. - Abstracts: To reveal the underlying mechanism of Mg influence on the enhanced post-annealing stability of perpendicular Ta/CoFeB/Mg/MgO multilayers, the X-ray photoelectron spectroscopy analysis has been performed. It is found that a certain amount of Mg interlayer at the CoFeB/MgO interface could prevent the Ta oxidation, and consequently lower the diffusion motivation of Ta from the bottom layer to the CoFeB/MgO interfaces to some extent in the annealing process. The prevention of Ta diffusion realizes the effective hybridization of Fe and O at the CoFeB/MgO interface and maintains interfacial magnetic anisotropy (KCoFeB/MgO). As a result, the perpendicular magnetic anisotropy at high annealing temperatures is maintained

  5. Superstructure Ta2O5 mesocrystals derived from (NH4)2Ta2O3F6 mesocrystals with efficient photocatalytic activity.

    Science.gov (United States)

    Yu, Xin; Li, Wei; Huang, Jian; Li, Zhonghua; Liu, Jiawen; Hu, PingAn

    2018-02-06

    Superstructured mesocrystalline Ta 2 O 5 nanosheets were successfully prepared from mesocrystalline (NH 4 ) 2 Ta 2 O 3 F 6 nanorods by the annealing method for the first time. The as-prepared mesocrystalline Ta 2 O 5 nanosheets in this work showed remarkable visible light absorption, mainly due to the formation of oxygen vacancy defects in the mesocrystalline Ta 2 O 5 nanosheets, which was also confirmed by XPS spectra, Raman spectra and EPR spectra. Besides, the mesocrystalline Ta 2 O 5 nanosheets showed a highly enhanced photocatalytic activity of 11 268.24 μmol g -1 h -1 , about 3.95 times that of commercial Ta 2 O 5 . Moreover, the specific surface area of the mesocrystalline Ta 2 O 5 -800 nanosheets was 16.34 m 2 g -1 , about 5.32 times that of the commercial Ta 2 O 5 (3.072 m 2 g -1 ). The valence band XPS spectra indicated a strong oxidizing ability of the mesocrystalline Ta 2 O 5 nanosheets in comparison to that of commercial Ta 2 O 5 . The formation of superstructured Ta 2 O 5 mesocrystals generated long lifetime carriers and effective conduction pathways, which greatly enhanced the photocatalytic activity for hydrogen production.

  6. Modelling the mechanical behaviour of heterogeneous Ta/TA6V welded joints: behaviour and failure criteria

    International Nuclear Information System (INIS)

    Paris, Th.

    2008-12-01

    As laser welding of two different materials (heterogeneous welding) leads to a joint having a characteristic size close to the millimetre, i.e. much smaller than that of a structure, and as such a junction displays completely different mechanical properties because of the metallurgical transformations induced by intense thermal loading, the aim of this research thesis is to develop a behaviour model, flexible and robust enough, to represent all together the mechanical behaviours of the Ta, the TA6V and the melted zone. This model must be able to take plasticity and visco-plasticity into account, and also to provide a failure criterion through damage mechanics and its coupling with the behaviour. The author first reports the experimental characterization of the base materials (Ta and TA6V) by using tensile tests under different strain rates and different directions, relaxation tests and fatigue shear tests. He also characterizes the melted zone by describing the influence of a thermal treatment (induced by welding) on the formation of the melted zone, and by using different tests: four point bending on notched specimens, nano-indentation test, and longitudinal tensile test. In a second part, the author develops the model within the framework of continuum thermodynamics, and explores the numerical issues. The last part deals with the validation of the model for the concerned materials (Ta and TA6V) and melted zone

  7. The wheat WRKY transcription factors TaWRKY49 and TaWRKY62 confer differential high-temperature seedling-plant resistance to Puccinia striiformis f. sp. tritici.

    Directory of Open Access Journals (Sweden)

    Junjuan Wang

    Full Text Available WRKY transcription factors (TFs play crucial roles in plant resistance responses to pathogens. Wheat stripe rust, caused by the fungal pathogen Puccinia striiformis f. sp. tritici (Pst, is a destructive disease of wheat (Triticum aestivum worldwide. In this study, the two WRKY genes TaWRKY49 and TaWRKY62 were originally identified in association with high-temperature seedling-plant resistance to Pst (HTSP resistance in wheat cultivar Xiaoyan 6 by RNA-seq. Interestingly, the expression levels of TaWRKY49 and TaWRKY62 were down- and up-regulated, respectively, during HTSP resistance in response to Pst. Silencing of TaWRKY49 enhanced whereas silencing TaWRKY62 reduced HTSP resistance. The enhanced resistance observed on leaves following the silencing of TaWRKY49 was coupled with increased expression of salicylic acid (SA- and jasmonic acid (JA-responsive genes TaPR1.1 and TaAOS, as well as reactive oxygen species (ROS-associated genes TaCAT and TaPOD; whereas the ethylene (ET-responsive gene TaPIE1 was suppressed. The decreased resistance observed on leaves following TaWRKY62 silencing was associated with increased expression of TaPR1.1 and TaPOD, and suppression of TaAOS and TaPIE1. Furthermore, SA, ET, MeJA (methyl jasmonate, hydrogen peroxide (H2O2 and abscisic acid (ABA treatments increased TaWRKY62 expression. On the other hand, MeJA did not affect the expression of TaWRKY49, and H2O2 reduced TaWRKY49 expression. In conclusion, TaWRKY49 negatively regulates while TaWRKY62 positively regulates wheat HTSP resistance to Pst by differential regulation of SA-, JA-, ET and ROS-mediated signaling.

  8. Resonances in odd-odd 182Ta

    Science.gov (United States)

    Brits, C. P.; Wiedeking, M.; Bello Garrote, F. L.; Bleuel, D. L.; Giacoppo, F.; Görgen, A.; Guttormsen, M.; Hadynska-Klek, K.; Hagen, T. W.; Ingeberg, V. W.; Kheswa, B. V.; Klintefjord, M.; Larsen, A. C.; Malatji, K. L.; Nyhus, H. T.; Papka, P.; Renstrøm, T.; Rose, S.; Sahin, E.; Siem, S.; Tveten, G. M.; Zeiser, F.

    2017-09-01

    Enhanced γ-decay on the tail of the giant electric dipole resonance, such as the scissors or pygmy resonances, can have significant impact on (n,γ) reaction rates. These rates are important input for modeling processes that take place in astrophysical environments and nuclear reactors. Recent results from the University of Oslo indicate the existence of a significant enhancement in the photon strength function for nuclei in the actinide region due to the scissors resonance. Further, the M1 strength distribution of the scissors resonances in rare earth nuclei has been studied extensively over the years. To investigate the evolution and persistence of the scissor resonance in other mass regions, an experiment was performed utilizing the NaI(Tl) γ-ray detector array (CACTUS) and silicon particle telescopes (SiRi) at the University of Oslo Cyclotron laboratory. Particle-γ coincidences from the 181Ta(d,p)182Ta and 181Ta(d,d')181Ta reactions were used to measure the nuclear level density and photon strength function of the well-deformed 181Ta and 182Ta systems, to investigate the existence of resonances below the neutron separation energy. Note to the reader: the title of this article has been corrected on September 19, 2017.

  9. Structural, mechanical, and electronic properties of TaB2, TaB, IrB2, and IrB: First-principle calculations

    International Nuclear Information System (INIS)

    Zhao Wenjie; Wang Yuanxu

    2009-01-01

    First-principle calculations were performed to investigate the structural, elastic, and electronic properties of TaB 2 , TaB, IrB 2 , and IrB. The calculated equilibrium structural parameters, shear modulus, and Young's modulus of TaB 2 are well consistent with the available experimental data, and TaB 2 with P6/mmm space group has stronger directional bonding between ions than WB 2 , OsB 2 , IrN 2 , and PtN 2 . For TaB 2 , the hexagonal P6/mmm structure is more stable than the orthorhombic Pmmn one, while for IrB 2 the orthorhombic Pmmn structure is the most stable one. The high shear modulus of P6/mmm phase TaB 2 is mainly due to the strong covalent π-bonding of B-hexagon in the (0001) plane. Such a B-hexagon network can strongly resist against an applied [112-bar0] (0001) shear deformation. Correlation between the hardness and the elastic constants of TaB 2 was discussed. The band structure shows that P6/mmm phase TaB 2 and Pmmn phase IrB 2 are both metallic. The calculations show that both TaB and IrB are elastically stable with the hexagonal P6 3 /mmc structure. - Elastic constant c 44 of TaB 2 is calculated to be 235 GPa. This value is exceptionally high, exceeding those of WB 2 , OsB 2 , WB 4 , OsN 2 , IrN 2 , and PtN 2 .

  10. TA-55 change control manual

    International Nuclear Information System (INIS)

    Blum, T.W.; Selvage, R.D.; Courtney, K.H.

    1997-11-01

    This manual is the guide for initiating change at the Plutonium Facility, which handles the processing of plutonium as well as research on plutonium metallurgy. It describes the change and work control processes employed at TA-55 to ensure that all proposed changes are properly identified, reviewed, approved, implemented, tested, and documented so that operations are maintained within the approved safety envelope. All Laboratory groups, their contractors, and subcontractors doing work at TA-55 follow requirements set forth herein. This manual applies to all new and modified processes and experiments inside the TA-55 Plutonium Facility; general plant project (GPP) and line item funded construction projects at TA-55; temporary and permanent changes that directly or indirectly affect structures, systems, or components (SSCs) as described in the safety analysis, including Facility Control System (FCS) software; and major modifications to procedures. This manual does not apply to maintenance performed on process equipment or facility SSCs or the replacement of SSCs or equipment with documented approved equivalents

  11. 75 FR 43564 - TA-W-71,483, Continental Airlines, Inc., Reservations Division, Houston, TX; TA-W-71,483A...

    Science.gov (United States)

    2010-07-26

    ... DEPARTMENT OF LABOR Employment and Training Administration TA-W-71,483, Continental Airlines, Inc., Reservations Division, Houston, TX; TA-W-71,483A, Continental Airlines, Inc., Reservations Division, Tampa, FL; TA-W-71,483B, Continental Airlines, Inc., Reservations Division, Salt Lake City, UT; Notice of...

  12. Energy-beam processing studies on Ta/U and Ir/Ta systems

    International Nuclear Information System (INIS)

    Kaufmann, E.N.; Peercy, P.S.; Jacobson, D.C.; Draper, C.W.; Huegel, F.J.; Echer, C.J.; Makowiecki, D.M.; Balser, J.D.

    1983-01-01

    Films of Ta metal on uranium and of Ir metal on tantalum have been irradiated and melted by pulses from Q-switched Ruby and frequency-doubled Nd:YAG lasers to investigate the nature of the resulting mixtures in light of the very different binary-phase diagrams of the two systems. In addition, a two-phase Ir-Ta alloy has been surface-processed with CW CO 2 -laser radiation and with an electron beam in order to study microstructure refinement and test the advantage of using alloys as opposed to film-on-substrate combinations for the development of claddings

  13. Pre-Test Analysis Predictions for the Shell Buckling Knockdown Factor Checkout Tests - TA01 and TA02

    Science.gov (United States)

    Thornburgh, Robert P.; Hilburger, Mark W.

    2011-01-01

    This report summarizes the pre-test analysis predictions for the SBKF-P2-CYL-TA01 and SBKF-P2-CYL-TA02 shell buckling tests conducted at the Marshall Space Flight Center (MSFC) in support of the Shell Buckling Knockdown Factor (SBKF) Project, NASA Engineering and Safety Center (NESC) Assessment. The test article (TA) is an 8-foot-diameter aluminum-lithium (Al-Li) orthogrid cylindrical shell with similar design features as that of the proposed Ares-I and Ares-V barrel structures. In support of the testing effort, detailed structural analyses were conducted and the results were used to monitor the behavior of the TA during the testing. A summary of predicted results for each of the five load sequences is presented herein.

  14. Characterization of Rh films on Ta(110)

    International Nuclear Information System (INIS)

    Jiang, L.Q.; Ruckman, M.W.; Strongin, M.

    1989-01-01

    The surface and electronic structure of Rh films on Ta(110) up to several monolayers thick on Ta(110) are characterized by photoemission, Auger emission, low energy electron diffraction and low energy ion scattering. From the variation of the Rh Auger peak-to-peak intensity as a function of evaporation time, Rh/Ta(110) appears to grow in the Stranski-Krastanov mode at room temperature. However, the LEIS data show that the Rh adatoms begin to cluster on Ta(110) before growth of the monolayer is completed. Diffuse LEED scattering suggests that the Rh films are disordered. Photoemission shows that Rh chemisorption on Ta(110) generates two peaks located at 1.2 and 2. 5 eV binding energy during the initial phase of thin film growth (0 3.7 ML). Photoemission data for CO covered surfaces show that CO dissociates on the Rh/Ta(110) surface for Rh coverages less than 2.5 ML and also show that the Rh clusters develop at least one site capable of molecular CO adsorption above 0.3 ML Rh coverage. 38 refs., 5 figs

  15. Safety assessment for TA-48 radiochemical operations

    International Nuclear Information System (INIS)

    1994-08-01

    The purpose of this report is to document an assessment performed to evaluate the safety of the radiochemical operations conducted at the Los Alamos National Laboratory operations area designated as TA-48. This Safety Assessment for the TA-48 radiochemical operations was prepared to fulfill the requirements of US Department of Energy (DOE) Order 5481.1B, ''Safety Analysis and Review System.'' The area designated as TA-48 is operated by the Chemical Science and Technology (CST) Division and is involved with radiochemical operations associated with nuclear weapons testing, evaluation of samples collected from a variety of environmental sources, and nuclear medicine activities. This report documents a systematic evaluation of the hazards associated with the radiochemical operations that are conducted at TA-48. The accident analyses are limited to evaluation of the expected consequences associated with a few bounding accident scenarios that are selected as part of the hazard analysis. Section 2 of this report presents an executive summary and conclusions, Section 3 presents pertinent information concerning the TA-48 site and surrounding area, Section 4 presents a description of the TA-48 radiochemical operations, and Section 5 presents a description of the individual facilities. Section 6 of the report presents an evaluation of the hazards that are associated with the TA-48 operations and Section 7 presents a detailed analysis of selected accident scenarios

  16. Drought-responsive WRKY transcription factor genes TaWRKY1 and TaWRKY33 from wheat confer drought and/or heat resistance in Arabidopsis.

    Science.gov (United States)

    He, Guan-Hua; Xu, Ji-Yuan; Wang, Yan-Xia; Liu, Jia-Ming; Li, Pan-Song; Chen, Ming; Ma, You-Zhi; Xu, Zhao-Shi

    2016-05-23

    Drought stress is one of the major causes of crop loss. WRKY transcription factors, as one of the largest transcription factor families, play important roles in regulation of many plant processes, including drought stress response. However, far less information is available on drought-responsive WRKY genes in wheat (Triticum aestivum L.), one of the three staple food crops. Forty eight putative drought-induced WRKY genes were identified from a comparison between de novo transcriptome sequencing data of wheat without or with drought treatment. TaWRKY1 and TaWRKY33 from WRKY Groups III and II, respectively, were selected for further investigation. Subcellular localization assays revealed that TaWRKY1 and TaWRKY33 were localized in the nuclei in wheat mesophyll protoplasts. Various abiotic stress-related cis-acting elements were observed in the promoters of TaWRKY1 and TaWRKY33. Quantitative real-time PCR (qRT-PCR) analysis showed that TaWRKY1 was slightly up-regulated by high-temperature and abscisic acid (ABA), and down-regulated by low-temperature. TaWRKY33 was involved in high responses to high-temperature, low-temperature, ABA and jasmonic acid methylester (MeJA). Overexpression of TaWRKY1 and TaWRKY33 activated several stress-related downstream genes, increased germination rates, and promoted root growth in Arabidopsis under various stresses. TaWRKY33 transgenic Arabidopsis lines showed lower rates of water loss than TaWRKY1 transgenic Arabidopsis lines and wild type plants during dehydration. Most importantly, TaWRKY33 transgenic lines exhibited enhanced tolerance to heat stress. The functional roles highlight the importance of WRKYs in stress response.

  17. Gold nanoparticles embedded in Ta 2 O 5 /Ta 3 N 5 as active visible-light plasmonic photocatalysts for solar hydrogen evolution

    KAUST Repository

    Luo, Yujing

    2014-07-10

    Here, we demonstrate a new recreating photocatalytic activity of a Nano Au/Ta2O5 composite for hydrogen evolution from water as a visible-light-responsive plasmonic photocatalyst by embedding Au nanoparticles in a Ta2O5 host lattice. The Nano Au/Ta2O 5 composite samples were prepared through a simple Pechini-type sol-gel process. Further nitridating Nano Au/Ta2O5 composite samples in ammonia flow at 1123 K yielded Nano Au/Ta3N 5 composite samples. The obtained Nano Au/Ta3N5 composite exhibited a significantly enhanced photocatalytic activity in the visible region for hydrogen evolution from water compared with blank Ta 3N5 nanoparticles. UV-visible diffuse reflectance spectra and photocatalytic activity measurements indicated that the excitation of surface plasmon resonance of Au nanoparticles is responsible for the new recreating photocatalytic activity of the Nano Au/Ta2O5 composite and significantly enhanced photocatalytic activity of the Nano Au/Ta3N5 composite for hydrogen evolution in the visible region, which might be ascribed to the charge transfer effect in Nano Au/Ta 2O5 composite and the synergetic effect of charge transfer and near-field electromagnetic effect in Nano Au/Ta3N5 composite induced by surface plasmon resonance of embedded Au nanoparticles. The current study could provide a new paradigm for designing plasmonic metal/semiconductor composite systems for photocatalytic, photovoltaic and other optoelectronic devices. © the Partner Organisations 2014.

  18. New ternary tantalum borides containing boron dumbbells: Experimental and theoretical studies of Ta{sub 2}OsB{sub 2} and TaRuB

    Energy Technology Data Exchange (ETDEWEB)

    Mbarki, Mohammed; Touzani, Rachid St.; Rehorn, Christian W.G.; Gladisch, Fabian C. [Institute of Inorganic Chemistry, RWTH Aachen University, D-52056 Aachen (Germany); Fokwa, Boniface P.T., E-mail: bfokwa@ucr.edu [Institute of Inorganic Chemistry, RWTH Aachen University, D-52056 Aachen (Germany); Department of Chemistry, University of California Riverside (UCR), Riverside, CA 92521 (United States)

    2016-10-15

    The new ternary transition metal-rich borides Ta{sub 2}OsB{sub 2} and TaRuB have been successfully synthesized by arc-melting the elements in a water-cooled crucible under an argon atmosphere. The crystal structures of both compounds were solved by single-crystal X-ray diffraction and their metal compositions were confirmed by EDX analysis. It was found that Ta{sub 2}OsB{sub 2} and TaRuB crystallize in the tetragonal Nb{sub 2}OsB{sub 2} (space group P4/mnc, no. 128) and the orthorhombic NbRuB (space group Pmma, no. 51) structure types with lattice parameters a=5.878(2) Å, c=6.857(2) Å and a=10.806(2) Å, b=3.196(1) Å, c=6.312(2) Å, respectively. Furthermore, crystallographic, electronic and bonding characteristics have been studied by density functional theory (DFT). Electronic structure relaxation has confirmed the crystallographic parameters while COHP bonding analysis indicates that B{sub 2}-dummbells are the strongest bonds in both compounds. Moreover, the formation of osmium dumbbells in Ta{sub 2}OsB{sub 2} through a Peierls distortion along the c-axis, is found to be the origin of superstructure formation. Magnetic susceptibility measurements reveal that the two phases are Pauli paramagnets, thus confirming the theoretical DOS prediction of metallic character. Also hints of superconductivity are found in the two phases, however lack of single phase samples has prevented confirmation. Furthermore, the thermodynamic stability of the two modifications of AMB (A=Nb, Ta; M =Ru, Os) are studied using DFT, as new possible phases containing either B{sub 4}- or B{sub 2}-units are predicted, the former being the most thermodynamically stable modification. - Graphical abstract: The two new ternary tantalum borides, Ta{sub 2}OsB{sub 2} and TaRuB, have been discovered. Their crystal structures contain boron dumbbells, which are the strongest bonds. Peirls distortion is found responsible for Os{sub 2}-dumbbells formation in Ta{sub 2}OsB{sub 2}. Ta{sub 2}OsB{sub 2} and

  19. Social shaping of technology in TA and HTA

    DEFF Research Database (Denmark)

    Clausen, Christian; Yoshinaka, Yutaka

    2004-01-01

    The paper discusses how the social shaping of technology (SST) approach may be useful in understanding the role played by technology assessment within the context of technological development and change. It is proposed that an SST perspective on TA (or HTA) yields particular insight, regardless...... of whether or not the TA activity bases itself on a social shaping understanding of technology. This is because SST addresses the socially negotiated character of technological development, where TA itself may be construed as an element influencing the process of such negotiation. At the same time, TA...... is a construction, that is, itself a product of negotiations involving social actors. Thus, an understanding that TA is socially shaped, and is involved in the shaping of technology, opens up for a perspective on TA as both entailing constraints and enablements within the context of the particular agenda...

  20. Contribution have the survey of the transformation {sup 181}Hf {yields} {sup 181}Ta (17 {mu}s) {yields} {sup 181}Ta; Contribution a l'etude de la transformation {sup 181}Hf {yields} {sup 181}Ta (17 {mu}s) {yields} {sup 181}Ta

    Energy Technology Data Exchange (ETDEWEB)

    Baullini, R; Chaminade, R; Desneiges, P; Grjebine, T; Quidort, J; Wahl, R [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires

    1953-07-01

    The metastable state of Ta, whose period is around 20 microseconds, has been discovered by De BENEDETTI and Mc GOWAM who done measurements of deferred coincidences between the particles beta and the electrons of conversion given out by the hafnium radiated by thermal neutrons. We measured the period of {sup 181}Ta{sup *} by measures of deferred coincidences {beta}-e{sup -} and {beta}-{gamma}. A method of survey of the specter of photons amplitudes emitted by {sup 181}Ta{sup *} has been fit. This method permitted to solve the presence of {gamma} in the radiation emitted in synchronism with the deexcitation of {sup 181}Ta{sup *}. Finally in a last chapter, we propose a method of dosage of the {sup 181}Hf in presence of other radioelements. (M.B.) [French] L'etat metastable de Ta, dont la periode est voisine de 20 microsecondes, a ete decouvert par DE BENEDETTI et Mc GOWAM qui effectuaient des mesures de coincidences differees entre les particules beta et les electrons de conversion emis par du hafnium irradie par des neutrons thermiques. Nous avons mesure la periode de {sup 181}Ta{sup *} par des mesures de coincidences differees {beta}-e{sup -} et {beta}-{gamma}. Une methode d'etude du spectre d'amplitudes des photons emis par {sup 181}Ta{sup *} a ete mise au point. Cette methode a permis d'eclaircir la presence de {gamma} dans le rayonnement emis en synchronisme avec la desexcitation de {sup 181}Ta{sup *}. Enfin dans un dernier chapitre, on proposera une methode de dosage du {sup 181}Hf en presence d'autres radioelements. (M.B.)

  1. Two transcription factors TaPpm1 and TaPpb1 co-regulate anthocyanin biosynthesis in purple pericarps of wheat

    Science.gov (United States)

    Jiang, Wenhui; Liu, Tianxiang; Nan, Wenzhi; Jeewani, Diddugodage Chamila; Niu, Yanlu; Li, Chunlian; Shi, Xue; Wang, Cong; Wang, Jiahuan; Li, Yang; Wang, Zhonghua

    2018-01-01

    Abstract Purple pericarps of bread wheat (Triticum aestivum L.) are a useful source of dietary anthocyanins. Previous mapping results indicated that the purple pericarp trait is controlled by two complementary genes located on chromosomes 7D and 2A. However, the identity of the genes and the mechanisms by which they regulate the trait are unknown. In this study, two transcription factors were characterised as anthocyanin activators in purple pericarps: TaPpm1 (purple pericarp-MYB 1) and TaPpb1 (purple pericarp-bHLH 1). Three non-functional variants were detected in the coding sequence of TaPpm1 from non-purple seed lines, in which the function of TaPpm1 was destroyed either by insertion-induced frame shifts or truncated peptides. There were six 261-bp tandem repeats in the promoter region of TaPpb1 in the purple-grained varieties, while there was only one repeat unit present in the non-purple varieties. Furthermore, using yeast two-hybrid, dual luciferase, yeast one-hybrid, and transient assays, we were able to demonstrate that the interaction of TaPpm1 and TaPpb1 co-regulates the synthesis of anthocyanin. Overall, our results provide a better understanding of the molecular basis of anthocyanin synthesis in the wheat pericarp and indicate the existence of an integrated regulatory mechanism that controls production. PMID:29562292

  2. The Wheat Mediator Subunit TaMED25 Interacts with the Transcription Factor TaEIL1 to Negatively Regulate Disease Resistance against Powdery Mildew.

    Science.gov (United States)

    Liu, Jie; Zhang, Tianren; Jia, Jizeng; Sun, Jiaqiang

    2016-03-01

    Powdery mildew, caused by the biotrophic fungal pathogen Blumeria graminis f. sp. tritici, is a major limitation for the production of bread wheat (Triticum aestivum). However, to date, the transcriptional regulation of bread wheat defense against powdery mildew remains largely unknown. Here, we report the function and molecular mechanism of the bread wheat Mediator subunit 25 (TaMED25) in regulating the bread wheat immune response signaling pathway. Three homoalleles of TaMED25 from bread wheat were identified and mapped to chromosomes 5A, 5B, and 5D, respectively. We show that knockdown of TaMED25 by barley stripe mosaic virus-induced gene silencing reduced bread wheat susceptibility to the powdery mildew fungus during the compatible plant-pathogen interaction. Moreover, our results indicate that MED25 may play a conserved role in regulating bread wheat and barley (Hordeum vulgare) susceptibility to powdery mildew. Similarly, bread wheat ETHYLENE INSENSITIVE3-LIKE1 (TaEIL1), an ortholog of Arabidopsis (Arabidopsis thaliana) ETHYLENE INSENSITIVE3, negatively regulates bread wheat resistance against powdery mildew. Using various approaches, we demonstrate that the conserved activator-interacting domain of TaMED25 interacts physically with the separate amino- and carboxyl-terminal regions of TaEIL1, contributing to the transcriptional activation activity of TaEIL1. Furthermore, we show that TaMED25 and TaEIL1 synergistically activate ETHYLENE RESPONSE FACTOR1 (TaERF1) transcription to modulate bread wheat basal disease resistance to B. graminis f. sp. tritici by repressing the expression of pathogenesis-related genes and deterring the accumulation of reactive oxygen species. Collectively, we identify the TaMED25-TaEIL1-TaERF1 signaling module as a negative regulator of bread wheat resistance to powdery mildew. © 2016 American Society of Plant Biologists. All Rights Reserved.

  3. Electric-field gradients at Ta donor impurities in Cr{sub 2}O{sub 3}(Ta) semiconductor

    Energy Technology Data Exchange (ETDEWEB)

    Darriba, G.N. [Departamento de Fisica and IFLP (CONICET-UNLP), Facultad de Ciencias Exactas, Universidad Nacional de La Plata, CC 67, 1900 La Plata (Argentina); Errico, L.A. [Departamento de Fisica and IFLP (CONICET-UNLP), Facultad de Ciencias Exactas, Universidad Nacional de La Plata, CC 67, 1900 La Plata (Argentina); Universidad Nacional del Noroeste Bonaerense (UNNOBA), Monteagudo 2772, 2700 Pergamino (Argentina); Munoz, E.L; Richard, D. [Departamento de Fisica and IFLP (CONICET-UNLP), Facultad de Ciencias Exactas, Universidad Nacional de La Plata, CC 67, 1900 La Plata (Argentina); Eversheim, P.D. [Helmholtz-Institut fuer Strahlen-und Kernphysik (H-ISKP), Universitaet Bonn, Nussallee 14-16, 53115 Bonn (Germany); Renteria, M., E-mail: renteria@fisica.unlp.edu.a [Departamento de Fisica and IFLP (CONICET-UNLP), Facultad de Ciencias Exactas, Universidad Nacional de La Plata, CC 67, 1900 La Plata (Argentina)

    2009-10-01

    We report perturbed-angular-correlation (PAC) experiments on {sup 181}Hf(->{sup 181}Ta)-implanted corundum Cr{sub 2}O{sub 3} powder samples in order to determine the magnitude and symmetry of the electric-field gradient (EFG) tensor at Ta donor impurity sites of this semiconductor. These results are analyzed in the framework of ab initio full-potential augmented-plane wave plus local orbitals (FP-APW+lo) calculations. The results are also compared with EFG results coming from PAC experiments in isomorphous alpha-Al{sub 2}O{sub 3} and alpha-Fe{sub 2}O{sub 3} doped with {sup 111}In->{sup 111}Cd and {sup 181}Hf->{sup 181}Ta tracers. This combined analysis enables us to quantify the magnitude of the lattice relaxations induced by the presence of the impurity and to determine the charge state of the impurity donor level introduced by Ta in the band gap of the semiconductor.

  4. Lithiotantite, ideally LiTa3O8

    Directory of Open Access Journals (Sweden)

    Aba C. Persiano

    2012-05-01

    Full Text Available Lithiotantite (lithium tritantalum octaoxide and lithiowodginite are natural dimorphs of LiTa3O8, corresponding to the laboratory-synthesized L-LiTa3O8 (low-temperature form and M-LiTa3O8 (intermediate-temperature form phases, respectively. Based on single-crystal X-ray diffraction data, this study presents the first structure determination of lithiotantite from a new locality, the Murundu mine, Jenipapo District, Itinga, Minas Gerais, Brazil. Lithiotantite is isotypic with LiNb3O8 and its structure is composed of a slightly distorted hexagonal close-packed array of O atoms stacked in the [-101] direction, with the metal atoms occupying half of the octahedral sites. There are four symmetrically non-equivalent cation sites, with three of them occupied mainly by (Ta5+ + Nb5+ and one by Li+. The four distinct octahedra share edges, forming two types of zigzag chains (A and B extending along the b axis. The A chains are built exclusively of (Ta,NbO6 octahedra (M1 and M2, whereas the B chains consist of alternating (Ta,NbO6 and LiO6 octahedra (M3 and M4, respectively. The average M1—O, M2—O, M3—O and M4—O bond lengths are 2.011, 2.004, 1.984, and 2.188 Å, respectively. Among the four octahedra, M3 is the least distorted and M4 the most. The refined Ta contents at the M1, M2 and M3 sites are 0.641 (2, 0.665 (2, and 0.874 (2, respectively, indicating a strong preference of Ta5+ for M3 in the B chain. The refined composition of the crystal investigated is Li0.96Mn0.03Na0.01Nb0.82Ta2.18O8.

  5. Combined experimental and theoretical assessments of the lattice dynamics and optoelectronics of TaON and Ta3N5

    KAUST Repository

    Nurlaela, Ela

    2015-06-15

    Presented herein is a detailed discussion of the properties of the lattice dynamic and optoelectronic properties of tantalum(V) oxynitride (TaON) and tantalum(V) nitride (Ta3N5), from experimental and theoretical standpoint. The active Raman and infra red (IR) frequencies of TaON and Ta3N5 were measured using confocal Raman and Fourier Transform Infrared spectroscopies (FTIR) and calculated using the linear response method within the density functional perturbation theory (DFPT). The detailed study leads to an exhaustive description of the spectra, including the symmetry of the vibrational modes. Electronic structures of these materials were computed using DFT within the range-separated hybrid HSE06 exchange–correlation formalism. Electronic and ionic contributions to the dielectric constant tensors of these materials were obtained from DFPT within the linear response method using the PBE functional. Furthermore, effective mass of photogenerated holes and electrons at the band edges of these compounds were computed from the electronic band structure obtained at the DFT/HSE06 level of theory. The results suggest that anisotropic nature in TaON and Ta3N5 is present in terms of dielectric constant and effective masses.

  6. Combined experimental and theoretical assessments of the lattice dynamics and optoelectronics of TaON and Ta3N5

    KAUST Repository

    Nurlaela, Ela; Harb, Moussab; Del Gobbo, Silvano; Vashishta, Manish; Takanabe, Kazuhiro

    2015-01-01

    Presented herein is a detailed discussion of the properties of the lattice dynamic and optoelectronic properties of tantalum(V) oxynitride (TaON) and tantalum(V) nitride (Ta3N5), from experimental and theoretical standpoint. The active Raman and infra red (IR) frequencies of TaON and Ta3N5 were measured using confocal Raman and Fourier Transform Infrared spectroscopies (FTIR) and calculated using the linear response method within the density functional perturbation theory (DFPT). The detailed study leads to an exhaustive description of the spectra, including the symmetry of the vibrational modes. Electronic structures of these materials were computed using DFT within the range-separated hybrid HSE06 exchange–correlation formalism. Electronic and ionic contributions to the dielectric constant tensors of these materials were obtained from DFPT within the linear response method using the PBE functional. Furthermore, effective mass of photogenerated holes and electrons at the band edges of these compounds were computed from the electronic band structure obtained at the DFT/HSE06 level of theory. The results suggest that anisotropic nature in TaON and Ta3N5 is present in terms of dielectric constant and effective masses.

  7. Structural and electronic investigations of PbTa4O11 and BiTa7O19 constructed from α-U3O8 types of layers

    Science.gov (United States)

    Boltersdorf, Jonathan; Maggard, Paul A.

    2015-09-01

    The PbTa4O11 and BiTa7O19 phases were prepared by ion-exchange and solid-state methods, respectively, and their structures were characterized by neutron time-of-flight diffraction and Rietveld refinement methods (PbTa4O11, R 3 (No. 146), a=6.23700(2) Å, c=36.8613(1) Å; BiTa7O19, P 6 bar c 2 (No. 188), a=6.2197(2) Å, c=20.02981(9) Å). Their structures are comprised of layers of TaO6 octahedra surrounded by three 7-coordinate Pb(II) cations or two 8-coordinate Bi(III) cations. These layers alternate down the c-axis with α-U3O8 types of single and double TaO7 pentagonal bipyramid layers. In contrast to earlier studies, both phases are found to crystallize in noncentrosymmetric structures. Symmetry-lowering structural distortions within PbTa4O11, i.e. R 3 bar c →R3, are found to be a result of the displacement of the Ta atoms within the TaO7 and TaO6 polyhedra, towards the apical and facial oxygen atoms, respectively. In BiTa7O19, relatively lower reaction temperatures leads to an ordering of the Bi/Ta cations within a lower-symmetry structure, i.e., P63/mcm→ P 6 bar c 2 . In the absence of Bi/Ta site disorder, the Ta-O-Ta bond angles decrease and the Ta-O bond distances increase within the TaO7 double layers. Scanning electron microscopy images reveal two particle morphologies for PbTa4O11, hexagonal rods and finer irregularly-shaped particles, while BiTa7O19 forms as aggregates of irregularly-shaped particles. Electronic-structure calculations confirm the highest-energy valence band states are comprised of O 2p-orbitals and the respective Pb 6s-orbital and Bi 6s-orbital contributions. The lowest-energy conduction band states are composed of Ta 5d-orbital contributions that are delocalized over the TaO6 octahedra and layers of TaO7 pentagonal bipyramids. The symmetry-lowering distortions in the PbTa4O11 structure, and the resulting effects on its electronic structure, lead to its relatively higher photocatalytic activity compared to similar structures without

  8. Effects of thickness and annealing condition on magnetic properties and thermal stabilities of Ta/Nd/NdFeB/Nd/Ta sandwiched films

    International Nuclear Information System (INIS)

    Liu Wen-Feng; Zhang Min-Gang; Zhang Ke-Wei; Zhang Hai-Jie; Chai Yue-Sheng; Xu Xiao-Hong

    2016-01-01

    Ta/Nd/NdFeB/Nd/Ta sandwiched films are deposited by magnetron sputtering on Si (100) substrates, and subsequently annealed in vacuum at different temperatures for different time. It is found that both the thickness of NdFeB and Nd layer and the annealing condition can affect the magnetic properties of Ta/Nd/NdFeB/Nd/Ta films. Interestingly, the thickness and annealing temperature show the relevant behaviors that can affect the magnetic properties of the film. The high coercivity of 24.1 kOe (1 Oe = 79.5775 A/m) and remanence ratio (remanent magnetization/saturation magnetization) of 0.94 can be obtained in a Ta/Nd(250 nm)/NdFeB(600 nm)/Nd(250 nm)/Ta film annealed for 3 min at 1023 K. In addition, the thermal stability of the film is also linked to the thickness of NdFeB and Nd layer and the annealing temperature as well. The excellent thermal stability can be achieved in a Ta/Nd(250 nm)/NdFeB(600 nm)/Nd(250 nm)/Ta film annealed at 1023 K. (paper)

  9. Anodic oxidation of Ta/Fe alloys

    International Nuclear Information System (INIS)

    Mato, S.; Alcala, G.; Thompson, G.E.; Skeldon, P.; Shimizu, K.; Habazaki, H.; Quance, T.; Graham, M.J.; Masheder, D.

    2003-01-01

    The behaviour of iron during anodizing of sputter-deposited Ta/Fe alloys in ammonium pentaborate electrolyte has been examined by transmission electron microscopy, Rutherford backscattering spectroscopy, glow discharge optical emission spectroscopy and X-ray photoelectron spectroscopy. Anodic films on Ta/1.5 at.% Fe, Ta/3 at.% Fe and Ta/7 at.% Fe alloys are amorphous and featureless and develop at high current efficiency with respective formation ratios of 1.67, 1.60 and 1.55 nm V -1 . Anodic oxidation of the alloys proceeds without significant enrichment of iron in the alloy in the vicinity of the alloy/film interface and without oxygen generation during film growth, unlike the behaviour of Al/Fe alloys containing similar concentrations of iron. The higher migration rate of iron species relative to that of tantalum ions leads to the formation of an outer iron-rich layer at the film surface

  10. Characterization of Rh films on Ta(110)

    International Nuclear Information System (INIS)

    Jiang, L.Q.; Ruckman, M.W.; Strongin, M.

    1990-01-01

    The surface and electronic structure of Rh films on Ta(110) up to several monolayers thick on Ta(110) are characterized by photoemission, Auger emission, low-energy electron diffraction (LEED) and low-energy ion scattering (LEIS). From the variation of the Rh Auger peak-to-peak intensity as a function of evaporation time, Rh appears to grow in the Stranski--Krastanov mode at room temperature. However, the LEIS data show that the Rh adatoms begin to cluster on Ta(110) before growth of the monolayer is completed. Diffuse LEED scattering suggests that the Rh films are disordered. Photoemission shows that Rh chemisorption on Ta(110) generates two peaks located at -1.5 and -2.5 eV binding energy during the initial phase of thin-film growth (0 3.7 ML). CO dissociates on the Rh/Ta(110) surface for Rh coverages<2.5 ML and the surface develops a site capable of molecular CO adsorption above 0.3-ML Rh coverage

  11. Cloning and Functional Analysis of MADS-box Genes, TaAG-A and TaAG-B, from a Wheat K-type Cytoplasmic Male Sterile Line

    Directory of Open Access Journals (Sweden)

    Wenlong Yang

    2017-06-01

    Full Text Available Wheat (Triticum aestivum L. is a major crop worldwide. The utilization of heterosis is a promising approach to improve the yield and quality of wheat. Although there have been many studies on wheat cytoplasmic male sterility, its mechanism remains unclear. In this study, we identified two MADS-box genes from a wheat K-type cytoplasmic male sterile (CMS line using homology-based cloning. These genes were localized on wheat chromosomes 3A and 3B and named TaAG-A and TaAG-B, respectively. Analysis of TaAG-A and TaAG-B expression patterns in leaves, spikes, roots, and stems of Chinese Spring wheat determined using quantitative RT-PCR revealed different expression levels in different tissues. TaAG-A had relatively high expression levels in leaves and spikes, but low levels in roots, while TaAG-B had relatively high expression levels in spikes and lower expression in roots, stems, and leaves. Both genes showed downregulation during the mononucleate to trinucleate stages of pollen development in the maintainer line. In contrast, upregulation of TaAG-B was observed in the CMS line. The transcript levels of the two genes were clearly higher in the CMS line compared to the maintainer line at the trinucleate stage. Overexpression of TaAG-A and TaAG-B in Arabidopsis resulted in phenotypes with earlier reproductive development, premature mortality, and abnormal buds, stamens, and stigmas. Overexpression of TaAG-A and TaAG-B gives rise to mutants with many deformities. Silencing TaAG-A and TaAG-B in a fertile wheat line using the virus-induced gene silencing (VIGS method resulted in plants with green and yellow striped leaves, emaciated spikes, and decreased selfing seed set rates. These results demonstrate that TaAG-A and TaAG-B may play a role in male sterility in the wheat CMS line.

  12. Technical Area V (TA-V) transformation project close-out report.

    Energy Technology Data Exchange (ETDEWEB)

    2010-07-01

    Sandia National Laboratories (SNL) Technical Area V (TA-V) has provided unique nuclear experimental environments for decades. The technologies tested in TA-V facilities have furthered the United States Nuclear Weapons program and has contributed to the national energy and homeland security mission. The importance of TA-V working efficiently to produce an attractive and effective platform for experiments should not be underestimated. Throughout its brief history, TA-V has evolved to address multiple and diverse sets of requirements. These requirements evolved over many years; however, the requirements had not been managed nor communicated comprehensively or effectively. A series of programmatic findings over several years of external audits was evidence of this downfall. Today, these same requirements flow down through a new TA-V management system that produces consistently applied and reproducible approaches to work practices. In 2008, the TA-V department managers assessed the state of TA-V services and work activities to understand how to improve customer interfaces, stakeholders perceptions, and workforce efficiencies. The TA-V management team initiated the TA-V Transformation Project after they deemed the pre-June 2008 operational model to be ineffective in managing work and in providing integrated, continuous improvement to TA-V processes. This report summarizes the TA-V Transformation Project goals, activities, and accomplishments.

  13. Crystallization and atomic diffusion behavior of high coercive Ta/Nd-Fe-B/Ta-based permanent magnetic thin film

    Energy Technology Data Exchange (ETDEWEB)

    Tian, Na; Zhang, Xiao; You, Caiyin; Fu, Huarui [Xi' an University of Technology, School of Materials Science and Engineering, Xi' an (China); Shen, Qianlong [Logistics University of People' s Armed Police Force, Tianjin (China)

    2017-06-15

    A high coercivity of about 20.4 kOe was obtained through post-annealing the sputtered Ta/Nd-Fe-B/Ta-based permanent magnetic thin films. Transmission electron microscopy (TEM) and X-ray photoelectron spectroscopy (XPS) analyses were performed to investigate the crystallization and atomic diffusion behaviors during post-annealing. The results show that the buffer and capping Ta layers prefered to intermix with Fe and B atoms, and Nd tends to be combined with O atoms. The preferred atomic combination caused the appearance of the soft magnetic phase of Fe-Ta-B, resulting in a kink of the second quadratic magnetic hysteresis loop. The preferred atomic diffusion and phase formation of the thin films were well explained in terms of the formation enthalpy of the various compounds. (orig.)

  14. The Wheat Mediator Subunit TaMED25 Interacts with the Transcription Factor TaEIL1 to Negatively Regulate Disease Resistance against Powdery Mildew1

    Science.gov (United States)

    Zhang, Tianren; Jia, Jizeng; Sun, Jiaqiang

    2016-01-01

    Powdery mildew, caused by the biotrophic fungal pathogen Blumeria graminis f. sp. tritici, is a major limitation for the production of bread wheat (Triticum aestivum). However, to date, the transcriptional regulation of bread wheat defense against powdery mildew remains largely unknown. Here, we report the function and molecular mechanism of the bread wheat Mediator subunit 25 (TaMED25) in regulating the bread wheat immune response signaling pathway. Three homoalleles of TaMED25 from bread wheat were identified and mapped to chromosomes 5A, 5B, and 5D, respectively. We show that knockdown of TaMED25 by barley stripe mosaic virus-induced gene silencing reduced bread wheat susceptibility to the powdery mildew fungus during the compatible plant-pathogen interaction. Moreover, our results indicate that MED25 may play a conserved role in regulating bread wheat and barley (Hordeum vulgare) susceptibility to powdery mildew. Similarly, bread wheat ETHYLENE INSENSITIVE3-LIKE1 (TaEIL1), an ortholog of Arabidopsis (Arabidopsis thaliana) ETHYLENE INSENSITIVE3, negatively regulates bread wheat resistance against powdery mildew. Using various approaches, we demonstrate that the conserved activator-interacting domain of TaMED25 interacts physically with the separate amino- and carboxyl-terminal regions of TaEIL1, contributing to the transcriptional activation activity of TaEIL1. Furthermore, we show that TaMED25 and TaEIL1 synergistically activate ETHYLENE RESPONSE FACTOR1 (TaERF1) transcription to modulate bread wheat basal disease resistance to B. graminis f. sp. tritici by repressing the expression of pathogenesis-related genes and deterring the accumulation of reactive oxygen species. Collectively, we identify the TaMED25-TaEIL1-TaERF1 signaling module as a negative regulator of bread wheat resistance to powdery mildew. PMID:26813794

  15. Determination of the enthalpy of fusion of K{sub 3}TaF{sub 8} and K{sub 3}TaOF{sub 6}

    Energy Technology Data Exchange (ETDEWEB)

    Kosa, L. [Institute of Inorganic Chemistry, Slovak Academy of Sciences, SK-845 36 Bratislava (Slovakia)]. E-mail: uachkosa@savba.sk; Mackova, I. [Institute of Inorganic Chemistry, Slovak Academy of Sciences, SK-845 36 Bratislava (Slovakia)

    2006-08-15

    The areas of the fusion and crystallization peaks of K{sub 3}TaF{sub 8} and K{sub 3}TaOF{sub 6} have been measured using the DSC mode of the high-temperature calorimeter (SETARAM 1800 K). On the basis of these quantities and the temperature dependence of the used calorimetric method sensitivity, the values of the enthalpy of fusion of K{sub 3}TaF{sub 8} at temperature of fusion 1039 K: {delta}{sub fus} H {sub m}(K{sub 3}TaF{sub 8}; 1039 K) = (52 {+-} 2) kJ mol{sup -1} and of K{sub 3}TaOF{sub 6} at temperature of fusion 1055 K: {delta}{sub fus} H {sub m}(K{sub 3}TaOF{sub 6}; 1055 K) = (62 {+-} 3) kJ mol{sup -1} have been determined.

  16. Structure and physical properties of Cr{sub 5}B{sub 3}-type Ta{sub 5}Si{sub 3} and Ta{sub 5}Ge{sub 3}

    Energy Technology Data Exchange (ETDEWEB)

    Yuan, Fang; Forbes, Scott [Department of Chemistry and Chemical Biology, McMaster University, 1280 Main Street West, Hamilton, Ontario L8S 4M1 (Canada); Ramachandran, Krishna Kumar [Department of Chemistry, University of Alberta, Edmonton, Alberta T6G 2G2 (Canada); Mozharivskyj, Yurij, E-mail: mozhar@mcmaster.ca [Department of Chemistry and Chemical Biology, McMaster University, 1280 Main Street West, Hamilton, Ontario L8S 4M1 (Canada)

    2015-11-25

    The Cr{sub 5}B{sub 3}-type Ta{sub 5}Si{sub 3} phase was prepared by arc-melting, while the Cr{sub 5}B{sub 3}-type Ta{sub 5}Ge{sub 3} one was synthesized through sintering at 1000 °C. X-ray single crystal diffraction was employed to elucidate their structure. According to the magnetization measurements, both Ta{sub 5}Si{sub 3} and Ta{sub 5}Ge{sub 3} are Pauli paramagnets, with Ta{sub 5}Ge{sub 3} showing a Curie-Weiss-like paramagnetic behavior at low temperatures likely due to presence of paramagnetic impurity. Both Ta{sub 5}Si{sub 3} and Ta{sub 5}Ge{sub 3} display a very low electrical resistivity from 2 to 300 K. The resistivity is constant below 20 K, but displays a positive temperature coefficient above 20 K. Electronic structure calculations with the TB-LMTO-ASA method support the metallic character of the two phases and suggest that the bonding is optimized in both phases. - Highlights: • Synthesis of Cr{sub 5}B{sub 3}-type Ta{sub 5}Si{sub 3} and Ta{sub 5}Ge{sub 3} phases with high purity by arc-melting and sintering, respectively. • Magnetization data and electrical resistivity of the Cr{sub 5}B{sub 3}-type Ta{sub 5}Si{sub 3} and Ta{sub 5}Ge{sub 3} phases. • Crystal and electronic structure analysis for Ta{sub 5}Si{sub 3} and Ta{sub 5}Ge{sub 3} phase by X-ray diffraction and TB-LMTO-ASA calculations.

  17. Phase diagrams for pseudo-binary carbide systems TiC-NbC, TiC-TaC, ZrC-NbC, ZrC-TaC and HfC-TaC

    International Nuclear Information System (INIS)

    Gusev, A.I.

    1985-01-01

    Parameters of interaction and energy of mutual exchange in the liquid and solid phases of pseudobinary TiC-NbC, TiC-TaC, ZrC-NbC, ZrC-TaC, HfC-TaC systems are calculated with account of dependence on composition and temperature. Positions of liquidus-solidus phase boundaries on the phase diagrams of the mentioned systems are calculated on the basis of the determined mutual exchange energies in approximati.on of subregular solutions. The existance of latent decomposition ranges in the solid phase on the phase diagrams of the investgated systems is established

  18. Superconductivity in palladium-doped 2H-TaS2

    Science.gov (United States)

    Zhou, M. H.; Li, X. C.; Dong, C.

    2018-06-01

    A series of Pd x TaS2 (0.01 ≤ x ≤ 0.08) samples were prepared and characterized via scanning electron microscope, x-ray powder diffraction, resistivity, magnetization and specific heat measurements. The lattice parameter c associated with the interlayer distance increases monotonically with the Pd content while the parameter a remains essentially constant. The crystal structure of Pd0.08TaS2 has been determined and refined by Rietveld refinement. Pd0.08TaS2 is hexagonal (space group: P31c) with lattice parameters a = 3.3151(1) Å, c = 12.1497(9) Å. The superconducting transition temperature T c (0.8 K) of TaS2 can be dramatically enhanced by Pd doping, and the maximum T c of 4.2 K, about five times the T c of pure TaS2, is obtained in Pd0.04TaS2. We have determined the superconducting parameters of Pd0.04TaS2, and found that the enhancement of T c can be attributed to the increase of density of states at the Fermi level. The charge density wave (CDW) of TaS2 is gradually suppressed with Pd doping and disappears in Pd0.06TaS2. This suggests that there is a competitive interplay between superconductivity and CDW in this system.

  19. Computer simulation of hydrogen diffusion and hydride precipitation at Ta/Zr bond interface. Hydrogen embrittlement in SUS304ULC/Ta/Zr explosive bonded joint

    International Nuclear Information System (INIS)

    Saida, Kazuyoshi; Fujimoto, Tetsuya; Nishimoto, Kazutoshi

    2010-01-01

    The concentration of hydrogen and precipitation of zirconium hydrides in Ta/Zr explosive bonded joint were analysed by computer simulation. Numerical model of hydride precipitation under hydrogen diffusion was simplified by the alternate model coupled the macroscopic hydrogen diffusion with the microscopic hydride precipitation. Effects of the initial hydrogen content in Ta, working degree of Zr and post-bond heat treatment on the hydrogen diffusion and hydride precipitation were investigated. Hydrogen was rapidly diffused from Ta substrate into Zr after explosive bonding and temporarily concentrated at Ta/Zr bond interface. Zirconium hydrides were precipitated and grew at Ta/Zr bond interface, and the precipitation zone of hydrides was enlarged with the lapse of time. The precipitation of zirconium hydrides was promoted when the initial hydrogen content in Ta and working degree of Zr were increased. The concentration of hydrogen and precipitation of hydrides at the bond interface were reduced and diminished by post-bond heat treatment at 373 K. It was deduced that hydrogen embrittlement in Ta/Zr explosive bonded joint was caused by the precipitation of zirconium hydrides and concentration of hydrogen at Ta/Zr bond interface during the diffusion of hydrogen containing in Ta substrate. (author)

  20. Wheat Brassinosteroid-Insensitive1 (TaBRI1 Interacts with Members of TaSERK Gene Family and Cause Early Flowering and Seed Yield Enhancement in Arabidopsis.

    Directory of Open Access Journals (Sweden)

    Akanksha Singh

    Full Text Available Brassinosteroids (BRs hormones are important for plant growth, development and immune responses. They are sensed by the transmembrane receptor kinase Brassinosteroid-Insensitive 1 (BRI1 when they bind to its extracellular Leu-rich repeat (LRR domain. We cloned and characterized the TaBRI1 from T. aestivum and raised overexpression transgenics in Arabidopsis to decipher its functional role. TaBRI1 protein consists of a putative signal peptide followed by 25 leucine rich repeats (LRR, a transmembrane domain and a C-terminal kinase domain. The analysis determined the interaction of TaBRI1 with five members of the wheat Somatic Embryogenesis Receptor Kinase (TaSERKs gene family (TaSERK1, TaSERK2, TaSERK3, TaSERK4 and TaSERK5, at the plasma membrane. Furthermore, overexpression of TaBRI1 in Arabidopsis leads to the early flowering, increased silique size and seed yield. Root growth analysis of TaBRI1 overexpressing transgenic plants showed hypersensitivity to epi-brassinolide (epi-BL hormone in a dose-dependent manner. Interestingly, transgenic Arabidopsis plants show thermotolerance phenotype at the seedling stages as revealed by chlorophyll content, photosystem II activity and membrane stability. The transcriptome profiling on the basis of microarray analysis indicates up-regulation of several genes related to brassinosteroid signaling pathway, abiotic stress response, defense response and transcription factors. These studies predict the possible role of TaBRI1 gene in plant growth and development imparting tolerance to thermal stress.

  1. Alkane metathesis with the tantalum methylidene [(≡SiO)Ta(=CH2)Me2]/[(≡SiO)2Ta(=CH2)Me] generated from well-defined surface organometallic complex [(≡SiO)TaVMe4

    KAUST Repository

    Chen, Yin; Abou-Hamad, Edy; Hamieh, Ali Imad Ali; Hamzaoui, Bilel; Emsley, Lyndon; Basset, Jean-Marie

    2015-01-01

    By grafting TaMe5 on Aerosil700, a stable, well-defined, silica-supported tetramethyl tantalum(V) complex, [(≡SiO)TaMe4], is obtained on the silica surface. After thermal treatment at 150 °C, the complex is transformed into two surface tantalum methylidenes, [(≡SiO)2Ta(=CH2)Me] and [(≡SiO)Ta(=CH2)Me2], which are active in alkane metathesis and comparable to the previously reported [(≡SiO)2TaHx]. Here we present the first experimental study to isolate and identify a surface tantalum carbene as the intermediate in alkane metathesis. A systematic experimental study reveals a new reasonable pathway for this reaction.

  2. Alkane metathesis with the tantalum methylidene [(≡SiO)Ta(=CH2)Me2]/[(≡SiO)2Ta(=CH2)Me] generated from well-defined surface organometallic complex [(≡SiO)TaVMe4

    KAUST Repository

    Chen, Yin

    2015-01-21

    By grafting TaMe5 on Aerosil700, a stable, well-defined, silica-supported tetramethyl tantalum(V) complex, [(≡SiO)TaMe4], is obtained on the silica surface. After thermal treatment at 150 °C, the complex is transformed into two surface tantalum methylidenes, [(≡SiO)2Ta(=CH2)Me] and [(≡SiO)Ta(=CH2)Me2], which are active in alkane metathesis and comparable to the previously reported [(≡SiO)2TaHx]. Here we present the first experimental study to isolate and identify a surface tantalum carbene as the intermediate in alkane metathesis. A systematic experimental study reveals a new reasonable pathway for this reaction.

  3. Suppression of wheat TaCDK8/TaWIN1 interaction negatively affects germination of Blumeria graminis f.sp. tritici by interfering with very-long-chain aldehyde biosynthesis.

    Science.gov (United States)

    Kong, Lingyao; Chang, Cheng

    2018-01-01

    Wheat TaCDK8 interacts with TaWIN1 to regulate very-long-chain aldehyde biosynthesis required for efficient germination of Blumeria graminis f.sp. tritici. Powdery mildew caused by Blumeria graminis f.sp. tritici (Bgt) is a devastating disease of common wheat (Triticum aestivum L.). Bgt infection initiates with its conidia germination on the aerial surface of wheat. In this study, we isolated the cyclin-dependent kinase 8 (TaCDK8) from wheat cultivar Jing411 and found that silencing of TaCDK8 impeded Bgt germination. The biochemical and molecular-biological assays revealed that TaCDK8 interacts with and phosphorylates the wheat transcription factor wax inducer 1 (TaWIN1) to stimulate the TaWIN1-dependent transcription. Bgt conidia on the leaves of TaWIN1-silenced plants also showed reduced germination. Gas chromatographic analysis revealed that knockdown of TaCDK8 or TaWIN1 resulted in decreases of wax components and cutin monomers in wheat leaves. Moreover, Bgt germination on leaves of TaCDK8 or TaWIN1 silenced plants could be fully restored by application of wild-type cuticular wax. In vitro studies demonstrated that very-long-chain aldehydes absent from the cuticular wax of the TaCDK8 or TaWIN1 silenced plants were capable of chemically stimulating Bgt germination. These results implicated that the suppression of TaCDK8/TaWIN1 interaction negatively affects Bgt germination by interfering with very-long-chain aldehyde biosynthesis required for efficient fungal germination.

  4. Phase relationships in the BaO-Ga2O3-Ta2O5 system and the structure of Ba6Ga21TaO40.

    Science.gov (United States)

    Cao, Jiang; Yu, Xiaodi; Kuang, Xiaojun; Su, Qiang

    2012-07-16

    Phase relationships in the BaO-Ga(2)O(3)-Ta(2)O(5) ternary system at 1200 °C were determined. The A(6)B(10)O(30) tetragonal tungsten bronze (TTB) related solution in the BaO-Ta(2)O(5) subsystem dissolved up to ~11 mol % Ga(2)O(3), forming a ternary trapezoid-shaped TTB-related solid solution region defined by the BaTa(2)O(6), Ba(1.1)Ta(5)O(13.6), Ba(1.58)Ga(0.92)Ta(4.08)O(13.16), and Ba(6)GaTa(9)O(30) compositions in the BaO-Ga(2)O(3)-Ta(2)O(5) system. Two ternary phases Ba(6)Ga(21)TaO(40) and eight-layer twinned hexagonal perovskite solid solution Ba(8)Ga(4-x)Ta(4+0.6x)O(24) were confirmed in the BaO-Ga(2)O(3)-Ta(2)O(5) system. Ba(6)Ga(21)TaO(40) crystallized in a monoclinic cell of a = 15.9130(2) Å, b = 11.7309(1) Å, c = 5.13593(6) Å, β = 107.7893(9)°, and Z = 1 in space group C2/m. The structure of Ba(6)Ga(21)TaO(40) was solved by the charge flipping method, and it represents a three-dimensional (3D) mixed GaO(4) tetrahedral and GaO(6)/TaO(6) octahedral framework, forming mixed 1D 5/6-fold tunnels that accommodate the Ba cations along the c axis. The electrical property of Ba(6)Ga(21)TaO(40) was characterized by using ac impedance spectroscopy.

  5. Gold nanoparticles embedded in Ta 2 O 5 /Ta 3 N 5 as active visible-light plasmonic photocatalysts for solar hydrogen evolution

    KAUST Repository

    Luo, Yujing; Liu, Xiaoming; Tang, Xinghua; Luo, Yan; Zeng, Qianyao; Deng, Xiaolei; Ding, Shaolei; Sun, Yiqun

    2014-01-01

    Here, we demonstrate a new recreating photocatalytic activity of a Nano Au/Ta2O5 composite for hydrogen evolution from water as a visible-light-responsive plasmonic photocatalyst by embedding Au nanoparticles in a Ta2O5 host lattice. The Nano Au/Ta2

  6. Thermal stability of Cu/α-Ta/SiO2/Si structures

    International Nuclear Information System (INIS)

    Yuan, Z.L.; Zhang, D.H.; Li, C.Y.; Prasad, K.; Tan, C.M.

    2004-01-01

    The thermal stability of the Cu/α-Ta/SiO 2 /Si structures is investigated. Tantalum oxides are first observed at the interface between Cu and Ta due to residual oxygen in the annealing ambient at low annealing temperatures (about 600 deg. C). Ternary Cu-Ta oxides and/or Ta oxides rather than Cu oxides are found at the Cu top layer on account of the out diffusion of Ta. After high temperature annealing (up to 750 deg. C), polycrystalline Tantalum oxides (Ta 2 O 5 ) and Ta-rich silicides (Ta 5 Si 3 ) are found as dominant products due to the dissociation of SiO 2 . A severe intermixing of Cu, Ta and SiO 2 was observed after 800 deg. C annealing. First a drop and then an increase in sheet resistances were observed, the former possibly resulting from grain growth and impurities removal in Cu films, and the latter from the reduction of Cu thickness and formation of high resistivity products. The α-Ta films with a thickness of 25 nm have good barrier effectiveness up to 750 deg. C. The degradation of α-Ta film is mainly caused by self oxidation, silicidation and bidirectional diffusion

  7. Synthesis and characterization of Cu3TaIn3Se7 and CuTa2InTe4

    International Nuclear Information System (INIS)

    Calderon, E.; Munoz-Pinto, M.; Duran-Pina, S.; Quintero, M.; Quintero, E.; Morocoima, M.; Delgado, G.E.; Romero, H.; Briceno, J.M.; Fernandez, J.; Grima-Gallardo, P.

    2008-01-01

    Polycrystalline samples of Cu 3 TaIn 3 Se 7 and CuTa 2 InTe 4 were synthesized by the usual melt and anneal technique. X-ray powder diffraction showed a single phase behavior for both samples with tetragonal symmetry and unit cell parameter values a=5.794±0.002 A, c=11.66±0.01 A, c/a=2.01, V=391±1 A 3 and a=6.193±0.001 A, c=12.400 ±0.002A, c/a=2.00, V=475±1 A 3 , respectively. Differential thermal analysis (DTA) measurements suggested a complicated behavior near the melting point with several thermal transitions observed in the heating and cooling runs. From the shape of the DTA peaks it was deduced that the melting is incongruent for both materials. Magnetic susceptibility measurements (zero-field cooling and field cooling) indicated an antiferromagnetic character with transition temperatures of T=70 K (Cu 3 TaIn 3 Se 7 ) and 42 K (CuTa 2 InTe 4 ). A spin-glass transition was observed in Cu 3 TaIn 3 Se 7 with T f ∼50 K. (copyright 2008 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim) (orig.)

  8. Comparative Raman study of Weyl semimetals TaAs, NbAs, TaP and NbP

    International Nuclear Information System (INIS)

    Liu, H W; Richard, P; Zhao, L X; Chen, G-F; Ding, H

    2016-01-01

    We report a comparative polarized Raman study of Weyl semimetals TaAs, NbAs, TaP and NbP. The evolution of the phonon frequencies with the sample composition allows us to determine experimentally which atoms are mainly involved for each vibration mode. Our results confirm previous first-principles calculations indicating that the A 1 , B 1 (2), E(2) and E(3) modes involve mainly the As(P) atoms, the B 1 (1) mode is mainly related to Ta(Nb) atoms, and the E(1) mode involves both kinds of atoms. By comparing the energy of the different modes, we establish that the B 1 (1), B 1 (2), E(2) and E(3) become harder with increasing chemical pressure. This behaviour differs from our observation on the A 1 mode, which decreases in energy, in contrast to its behaviour under external pressure. (paper)

  9. Role of Ta-spacer layer on tuning the tilt angle magnetic anisotropy of L1{sub 1}-CoPt/Ta/NiFe exchange springs

    Energy Technology Data Exchange (ETDEWEB)

    Saravanan, P., E-mail: psdrdo@gmail.com [Defence Metallurgical Research Laboratory, Hyderabad 500058 (India); Talapatra, A.; Mohanty, J. [Department of Physics, Indian Institute of Technology Hyderabad, Hyderabad 502285 (India); Hsu, Jen-Hwa, E-mail: jhhsu@phys.ntu.edu.tw [Department of Physics, National Taiwan University, Taipei 106, Taiwan (China); Kamat, S.V. [Defence Metallurgical Research Laboratory, Hyderabad 500058 (India)

    2017-06-15

    Highlights: • Role of Ta-spacer layer in L1{sub 1}-CoPt(10 nm)/Ta//NiFe(4 nm) trilayers was investigated. • Domain size increased at the expense of magnetic phase contrast with increasing t{sub Ta}. • Tilt angle magnetization increased from 43° to 77° upon increasing t{sub Ta} (0–2.5 nm). • Micromagnetic studies confirmed the existence of tilted magnetic anisotropy. • Ta-spacer is effective in preserving competing anisotropies of CoPt and NiFe-layers. - Abstract: L1{sub 1}-CoPt/Ta/NiFe trilayers are chosen as model films for probing the role of spacer layer on tuning the tilt angle magnetization (θ{sub M}) in such exchange springs. For this purpose, a non-magnetic layer (Ta) with varying thickness (t{sub Ta}) from 0 to 2.5 nm was inserted between 10-nm thick CoPt film exhibiting strong perpendicular magnetic anisotropy (PMA) and 4-nm thick NiFe film having in-plane magnetic anisotropy (IMA). With the insertion of Ta-spacer, the magnetic hysteresis loops become more and more tilted as t{sub Ta} increases. Upon increasing the t{sub Ta} from 0 to 2.5 nm, the estimated SQR{sub ⊥} (=M{sub r⊥}/M{sub s⊥}) from the M–H loops is found to decrease moderately; while the θ{sub M} increases significantly from 43° to 77°. MFM images revealed maze-like domain patterns and the domain size tends to increase at the expense of magnetic phase contrast with increasing t{sub Ta}. Micro-magnetic simulation of tilt in the anisotropy axis with respect to the bare CoPt-layer showed a trend similar to that of those observed with the M–H loops obtained by VSM measurements. The results of present study suggest that the insertion of Ta-spacer is not only beneficial in terms of preserving the competing anisotropies such as PMA and IMA of CoPt and NiFe-layers respectively through weakened exchange coupling; but also, act as an appropriate means for realizing tunable tilted magnetic anisotropy in the L1{sub 1}-CoPt/NiFe exchange springs.

  10. HIP (hot isostatic pressing) sintering of Tantalum (Ta) and tantalum carbide (TaC) powder mixture: relations between microstructure and properties

    International Nuclear Information System (INIS)

    Valin, F.; Schnedecker, M.

    1994-01-01

    HIP sintering at 1630 C and 195 MPa, during 2 hours, can be used for complete densification of mixtures of commercial tantalum carbide and tantalum powders. HIPed material properties are depending upon initial compositions. For C/Ta ratios inferior to 80%, the monocarbide structure is preserved. A partial ordering of the carbon vacancies will result, for TaC(0.80), in microhardness maximization. The microstructurally homogenous TaC(0.45) shows an excellent toughness. 2 figs., 2 refs

  11. 77 FR 64827 - Investigation Nos. 701-TA-402 and 731-TA-892 (Second Review); Honey From Argentina; Termination...

    Science.gov (United States)

    2012-10-23

    ... INTERNATIONAL TRADE COMMISSION Investigation Nos. 701-TA-402 and 731-TA-892 (Second Review); Honey... revocation of the countervailing duty order and antidumping duty order on imports of honey from Argentina would be likely to lead to continuation or recurrence of material injury. On September 21, 2012, the...

  12. Effects of thickness and annealing condition on magnetic properties and thermal stabilities of Ta/Nd/NdFeB/Nd/Ta sandwiched films

    Science.gov (United States)

    Liu, Wen-Feng; Zhang, Min-Gang; Zhang, Ke-Wei; Zhang, Hai-Jie; Xu, Xiao-Hong; Chai, Yue-Sheng

    2016-11-01

    Ta/Nd/NdFeB/Nd/Ta sandwiched films are deposited by magnetron sputtering on Si (100) substrates, and subsequently annealed in vacuum at different temperatures for different time. It is found that both the thickness of NdFeB and Nd layer and the annealing condition can affect the magnetic properties of Ta/Nd/NdFeB/Nd/Ta films. Interestingly, the thickness and annealing temperature show the relevant behaviors that can affect the magnetic properties of the film. The high coercivity of 24.1 kOe (1 Oe = 79.5775 A/m) and remanence ratio (remanent magnetization/saturation magnetization) of 0.94 can be obtained in a Ta/Nd(250 nm)/NdFeB(600 nm)/Nd(250 nm)/Ta film annealed for 3 min at 1023 K. In addition, the thermal stability of the film is also linked to the thickness of NdFeB and Nd layer and the annealing temperature as well. The excellent thermal stability can be achieved in a Ta/Nd(250 nm)/NdFeB(600 nm)/Nd(250 nm)/Ta film annealed at 1023 K. Program supported by the National Natural Science Foundation of China (Grant No. 51305290), the Higher Education Technical Innovation Project of Shanxi Province, China (Grant No. 2013133), the Fund Program for the Scientific Activities of Selected Returned Overseas Professionals of Shanxi Province, China (Grant No. 2015003), and the Program for the Key Team of Scientific and Technological Innovation of Shanxi Province, China (Grant No. 2013131009).

  13. Niobium Nb and tantalum Ta

    International Nuclear Information System (INIS)

    Busev, A.I.; Tiptsova, V.G.; Ivanov, V.M.

    1978-01-01

    The basic methods for determining niobium and tantalum in various objects are described. Nb and Ta are separated with the aid of N-benzoyl-N-phenylhydroxylamine by precipitating Nb(5) from a tartaric acid solution with subsequent precipitation of Ta from the filtrate. The gravimetric determination of Nb and Ta in steels is based on their quantitative separation from a diluted solution by way of hydrolysis with subsequent after-precipitation with phenylarsonic acid (in the absence of W). The gravimetric determination of Nb in the presence of W is carried out with the aid of Cupferron. To determine Nb in its carbide, Nb(5) reduced to Nb(3) is titrated with a solution of K 2 Cr 2 O 7 in the presence of phenyl-anthranilic acid. The photometric determination of Nb in tungsten-containing steels and in ores containing Ti, W, Mo and Cr is based on the rhodanide method. Nb is determined in alloys with Zr and Ti photometrically with the aid of 4-(2-pyridylazo)-resorcin and in alloyed steels with the aid of benzhydroxamic acid. The latter complex is extracted with chloroform. This method is used to determine Nb in rocks. The photometric determination of Ta in TiCl 4 is carried out with the aid of pyrogallol, in commercial niobium with the aid of methyl violet, and in steel with the aid of 4-(-pyridylazo)-resorcin. Also described is the polarographic determination of Nb in tantalum pentoxide

  14. Studies on layer growth and interfaces on Ta-base thin layers by means of XPS; Untersuchungen zu Schichtwachstum und Grenzflaechen an Ta-basierten Duennschichten mittels XPS

    Energy Technology Data Exchange (ETDEWEB)

    Zier, M.

    2007-11-02

    In this thesis studies on the growth and on the formation of the interfaces of Ta and TaN layers on Si and SiO{sub 2} were performed. In the system TaN on SiO{sub 2} no reaction on the interface could be found. As the system with the mostly disturbed interface Ta on SiO{sub 2} was proved. Here a reduction of the SiO{sub 2} at simultaneous oxidation of the Ta was to be observed. Additionally tantalum silicide was formed to be considered concerning the bonding state as Ta{sub 5}Si{sub 3}, from which a double layer of a tantalum silicide and a tantalum suboxide resulted. A whole thickness of the double layer of above 1 nm resulted. In the system Ta on Si at the deposition of the film on the interface a tantalum silicide was formed to be characterized concerning the bonding state as TaSi{sub 2}. The thickness of the interlayer growed thereby up to 0.8 nm in form of islands. Finally in the system TaN on Si a silicon nitride formation during the deposition was observed, which was attributed to the insertion of adsorbed nitrogen from the sputtering atmosphere by recoil implantation of the sputtered Ta atoms. The silicon nitride interlayer growed thereby up to a thickness of 0.8 nm.

  15. Creep rupture properties of laves phase strengthened Fe--Ta--Cr--W and Fe--Ta--Cr--W--Mo alloys

    International Nuclear Information System (INIS)

    Singh, S.

    1975-12-01

    A small addition of tungsten (0.5 at. percent) was shown to have an effect similar to that of molybdenum on the phase transformation characteristics of alloy Ta7Cr (with a nominal composition of 1 at. percent Ta, 7 at. percent Cr, balance Fe). The existence of time-temperature dependent transformation behavior in alloy Ta7Cr0.5W was confirmed. The effect of spheroidization time and temperature on creep strength was determined. In addition, effect of mechanical processing prior to aging, on creep strength was also determined. It was also shown that by suitable modifications of composition, the grain boundary film can be broken during the aging treatment without the use of spheroidization treatment. Microhardness, tensile and creep properties have been determined. Optical metallography and scanning electron microscopy have been used to follow the microstructural changes and mode of fracture. The creep rupture strength of alloy Ta7CrW alloy was found to be superior to many of the best commercially available ferritic alloys at 1200 0 F. (21 fig., 8 tables)

  16. Structures of Ta22W4O67 and Ta74W6O203. Pt. 1. Refined structural models using synchrotron radiation

    International Nuclear Information System (INIS)

    Schmid, S.

    1995-01-01

    The crystal structures of Ta 22 W 4 O 67 [M r = 5788.19, a = 6.1485 (5), b = 47.6205 (12), c = 3.8559 (3) A, γ = 90.04 (1) , space group = C112/m (non-standard setting), Z = 1, D x = 8.513 g cm -3 , F(000) = 2438] and Ta 74 W 6 O 203 [M r = 17741.06, a = 6.1664 (5), b = 29.2717 (14), c = 3.8731 (2) A, space group = Pbam (no. 55), Z = 0.2, D x = 8.428 g cm -3 , F(000) 1494] were determined using synchrotron radiation at four different wavelengths below the Ta L III edge [λ = 1.2741 (-146 eV), λ = 1.2586 (-26 eV), λ = 1.2571 (-14 eV) and λ = 1.2563 A (-8 eV)]. The collection of data immediately below the Ta L III edge at -8 eV enabled resolution of Ta and W of up to eight electrons, which assisted in the refinement of Ta/W ordering for both structures. Bond valence arguments have been used to locate oxygen vacancies required by the formulae. From the largest data set for Ta 22 W 4 O 67 (λ = 1.2741 A), a final value of 0.0481 for R 1 = Σ parallel F obs (h)vertical stroke - vertical stroke F calc (h) parallel /Σvertical stroke F obs (h)vertical stroke was obtained for 3082 unmerged reflections with I(h) > 3σ[I(h)] and for Ta 74 W 6 O 203 (λ = 1.2563 A) a final value of 0.0571 for R 1 was obtained for 5675 unmerged reflections. The two structures are described from a conventional polyhedral perspective as 13- and 8-times superstructures occurring in the solid solution (1-x)Ta 2 O 5 xWO 3 , 0 ≤ x ≤ 0.267. (orig.)

  17. An update on the thermodynamics of Ta2O5

    International Nuclear Information System (INIS)

    Jacob, K.T.; Shekhar, Chander; Waseda, Y.

    2009-01-01

    Using a solid-state electrochemical cell incorporating yttria-doped thoria (YDT) as the electrolyte and a mixture of (Mn + MnO) as the reference electrode, standard Gibbs free energy of formation of β-Ta 2 O 5 has been determined as a function of temperature in the range (1000 to 1300) K. The solid-state electrochemical cell used can be represented as (-)Pt,Ta+Ta 2 O 5 //(Y 2 O 3 )ThO 2 //Mn+MnO,Pt(+) Combining the reversible e.m.f. of the cell with recent data on the free energy of formation of MnO, standard Gibbs free energy of formation of Ta 2 O 5 from Ta metal and diatomic oxygen gas (O 2 ) in the temperature range (1000 to 1300) K is obtained: Δ f G 0 ±0.35/(kJ.mol -1 )=-2004.376+0.40445(T/K). Because of the significant solid solubility of oxygen in tantalum, a small correction for the activity of Ta in the metal phase in equilibrium with Ta 2 O 5 is applied. An analysis of the results obtained in this study and other free energy data reported in the literature by the 'third law' method suggests the need for refining data for Ta 2 O 5 reported in thermodynamic compilations. Used in the analysis is a revised value for standard entropy of Ta 2 O 5 based on more recent low-temperature heat capacity measurements. An improved set of thermodynamic properties of ditantalum pentoxide (Ta 2 O 5 ) are presented in the temperature range (298.15 to 2200) K.

  18. Moderní počítačové viry

    OpenAIRE

    Malina, Lukáš

    2008-01-01

    Bakalářská práce Moderní počítačové viry se skládá ze dvou hlavních cílů (Analýza počítačových virů a návrh zabezpečení střední počítačové sítě) rozdělených na tři části: Analýza počítačových virů, Vlastní návrh zabezpečení osobního počítače koncového uživatele (Terminálu) a Vlastní návrh zabezpečení střední počítačové sítě. V první části jsou analyzovány metody šíření a infekce, specifické vlastnosti a dopady počítačových virů na osobní počítače. V druhé části je uvedeno řešení zabezpečení o...

  19. Collective flows of protons and $\\pi^-$ mesons in $^{2}$H + C, Ta and He plus C, Ta collisions at 3.4 GeV/nucleon

    CERN Document Server

    Chkhaidze, L; Djobava, T; Kladnitskaya, E; Kharkhelauri, L; Uzhinsky, V

    2011-01-01

    Collective flows of protons and negative pions have been studied in (2)H + C, Ta and He + C, Ta collisions at an energy of 3.4 GeV/nucleon. The data have been obtained by the 2-m Propane Bubble Chamber (PBC-500) at JINR. It is found that the directed flow of protons and pi(-) mesons characterized by d /d(y) increases with increase of the mass numbers of colliding nucleus pairs; the elliptic proton flow points out of the reaction plane and also strengthens as the system mass increases; the negative pion directed flow is in the same reaction plane as the proton flow for the lighter (2H + C, He + C) systems and in the opposite direction for the heavier ((2)H + Ta, He + Ta) systems. In (2)H + C, He + C, C + C, C + Ne, (2)H + Ta, He + Ta, C + Cu, and C + Ta collisions, the linear dependence of directed and elliptic flow parameters from mass numbers of projectile and target nuclei, (A(P).A(T))(1/2), is similar for protons while for pi(-) mesons the dependence of directed flow parameters is stronger. The ultrarelati...

  20. Wheat TaSP gene improves salt tolerance in transgenic Arabidopsis thaliana.

    Science.gov (United States)

    Ma, Xiaoli; Cui, Weina; Liang, Wenji; Huang, Zhanjing

    2015-12-01

    A novel salt-induced gene with unknown functions was cloned through analysis of gene expression profile of a salt-tolerant wheat mutant RH8706-49 under salt stress. The gene was named Triticum aestivum salt-related protein (TaSP) and deposited in GenBank (Accession No. KF307326). Quantitative polymerase chain reaction (qPCR) results showed that TaSP expression was induced under salt, abscisic acid (ABA), and polyethylene glycol (PEG) stresses. Subcellular localization revealed that TaSP was mainly localized in cell membrane. Overexpression of TaSP in Arabidopsis could improve salt tolerance of 35S::TaSP transgenic Arabidopsis. 35S::TaSP transgenic Arabidopsis lines after salt stress presented better physiological indexes than the control group. In the non-invasive micro-test (NMT), an evident Na(+) excretion was observed at the root tip of salt-stressed 35S::TaSP transgenic Arabidopsis. TaSP promoter was cloned, and its beta-glucuronidase (GUS) activities before and after ABA, salt, cold, heat, and salicylic acid (SA) stresses were determined. Full-length TaSP promoter contained ABA and salt response elements. Copyright © 2015 Elsevier Masson SAS. All rights reserved.

  1. 77 FR 47671 - TA-W-81,520, T-Mobile USA, Inc., Call Center, Allentown, PA; TA-W-81,520G, T-Mobile USA, Inc...

    Science.gov (United States)

    2012-08-09

    ... DEPARTMENT OF LABOR Employment and Training Administration TA-W-81,520, T-Mobile USA, Inc., Call Center, Allentown, PA; TA- W-81,520G, T-Mobile USA, Inc., Headquarters Office, Bellevue, WA; Amended... of T-Mobile USA, Inc., Call Center, Allentown, Pennsylvania (TA-W-81,520), Fort Lauderdale, Florida...

  2. From Ba3Ta5O14N to LaBa2Ta5O13N2: Decreasing the optical band gap of a photocatalyst

    International Nuclear Information System (INIS)

    Anke, B.; Bredow, T.; Pilarski, M.; Wark, M.; Lerch, M.

    2017-01-01

    Yellow LaBa 2 Ta 5 O 13 N 2 was successfully synthesized as phase-pure material crystallizing isostructurally to previously reported Ba 3 Ta 5 O 14 N and mixed-valence Ba 3 Ta V 4 Ta IV O 15 . The electronic structure of LaBa 2 Ta 5 O 13 N 2 was studied theoretically with the range-separated hybrid method HSE06. The most stable structure was obtained when lanthanum was placed on 2a and nitrogen on 4h sites confirming Pauling's second rule. By incorporating nitrogen, the measured band gap decreases from ∼3.8 eV for the oxide via 2.74 eV for Ba 3 Ta 5 O 14 N to 2.63 eV for the new oxide nitride, giving rise to an absorption band well in the visible-light region. Calculated fundamental band gaps confirm the experimental trend. The atom-projected density of states has large contributions from N2p orbitals close to the valence band edge. These are responsible for the observed band gap reduction. Photocatalytic hydrogen formation was investigated and compared with that of Ba 3 Ta 5 O 14 N revealing significantly higher activity for LaBa 2 Ta 5 O 13 N 2 under UV-light. - Graphical abstract: X-ray powder diffraction pattern of LaBa 2 Ta 5 O 13 N 2 with the results of the Rietveld refinements. Inset: Unit cell of LaBa 2 Ta 5 O 13 N 2 and polyhedral representation of the crystal structure. - Highlights: • Synthesis of a new oxide nitride LaBa 2 Ta 5 O 13 N 2 . • Refinement of the crystal structure. • Quantum chemical calculations provided band gap close to the measured value. • New phase shows a higher photocatalytic H 2 evolution rate compared to prior tested Ba 3 Ta 5 O 14 N.

  3. Redetermination of Na(3)TaF(8).

    Science.gov (United States)

    Langer, Vratislav; Smrcok, Lubomír; Boca, Miroslav

    2010-09-01

    The crystal structure of trisodium octafluoridotantalate, Na(3)TaF(8), has been redetermined using diffractometer data collected at 153 K, resulting in more accurate bond distances and angles than obtained from a previous structure determination based on film data. The structure is built from layers running along [101], which are formed by distorted [TaF(8)] antiprisms and [NaF(6)] rectangular bipyramids sharing edges and corners. The individual layers are separated by eight-coordinated Na ions. Two atoms in the asymmetric unit are in special positions: the Ta atom is on a twofold axis in Wyckoff position 4e and one of the Na ions lies on an inversion centre in Wyckoff site 4d.

  4. Genome-Wide Identification of Cyclic Nucleotide-Gated Ion Channel Gene Family in Wheat and Functional Analyses of TaCNGC14 and TaCNGC16

    Directory of Open Access Journals (Sweden)

    Jia Guo

    2018-01-01

    Full Text Available Cyclic nucleotide gated channels (CNGCs play multifaceted roles in plants, particularly with respect to signaling processes associated with abiotic stress signaling and during host-pathogen interactions. Despite key roles during plant survival and response to environment, little is known about the activity and function of CNGC family in common wheat (Triticum aestivum L., a key stable food around the globe. In this study, we performed a genome-wide identification of CNGC family in wheat and identified a total 47 TaCNGCs in wheat, classifying these genes into four major groups (I–IV with two sub-groups (IVa and IVb. Sequence analysis revealed the presence of several conserved motifs, including a phosphate binding cassette (PBC and a “hinge” region, both of which have been hypothesized to be critical for the function of wheat CNGCs. During wheat infection with Pst, the transcript levels of TaCNGC14 and TaCNGC16, both members of group IVb, showed significant induction during a compatible interaction, while a reduction in gene expression was observed in incompatible interactions. In addition, TaCNGC14 and TaCNGC16 mRNA accumulation was significantly influenced by exogenously applied hormones, including abscisic acid (ABA, methyl jasmonate (MeJA, and salicylic acid (SA, suggesting a role in hormone signaling and/or perception. Silencing of TaCNGC14 and TaCNGC16 limited Pst growth and increased wheat resistance against Pst. The results presented herein contribute to our understanding of the wheat CNGC gene family and the mechanism of TaCNGCs signaling during wheat-Pst interaction.

  5. Graphite surface topography induced by Ta cluster impact and oxidative etching

    International Nuclear Information System (INIS)

    Reimann, C.T.; Olsson, L.; Erlandsson, R.; Henkel, M.; Urbassek, H.M.

    1998-01-01

    Freshly cleaved highly oriented pyrolytic graphite (HOPG), when baked in air at ∝630 C, forms one-monolayer(ML)-deep circular pits due to oxidation initiated at surface defect sites. We found that the areal density and depths of these pits could be modulated by deliberately introducing surface and sub-surface defects by energetic ion bombardment prior to baking. Bombardment by 555-eV/atom Ta 1 + , Ta 2 + , Ta 4 + , or Ta 9 + , always enhanced the areal density of etch pits, but only bombardment by Ta 4 + , or Ta 9 + significantly enhanced the depths of the pits. We performed molecular dynamics simulations of Ta n cluster bombardment of HOPG (n = 1, 2, 4, and 9) with the aim of characterizing the damage structures induced by the bombardment and correlating them with the experimental data. For Ta 9 + , the simulations showed a high level of damage extending from the surface down to nine MLs, in agreement with the most probable etch pit depth observed. For other cluster species, predicted etch pit depths were deeper than the observed ones. Annealing or steric requirements for initiating oxidation may account for some of the differences between simulations and experimental results. (orig.)

  6. Preparation of Ta Te2 thin films by laser ablation

    International Nuclear Information System (INIS)

    Zidan, M.D.; Alkhwam, M.; Alkhasm, M.

    2006-03-01

    The laser ablation system consisting of a vacuum chamber and Nd-YAG laser has been built for deposition TaTe 2 on three different substrates (Silicon, glass, and Aluminium). The surface topography of the prepared thin films has been studied by atomic force microscopy (AFM). TaTe 2 powder was characterized by using x-ray diffraction. The crystallinity of the thin films was examined by x-ray diffraction (XRD). The results show no peaks corresponding TaTe 2 , but there are some indications to the Ta 3 N 5 . (author)

  7. Low emissivity Ag/Ta/glass multilayer thin films deposited by sputtering

    International Nuclear Information System (INIS)

    Park, Sun Ho; Lee, Kee Sun; Sivasankar Reddy, A.

    2011-01-01

    Ta is deposited on a glass substrate as an interlayer for the two-dimensional growth of Ag thin films because Ta has good thermal stability and can induce a negative surface-energy change in Ag/glass. From the transmission electron microscopy results, we concluded that the Ag crystals in the bottom layer (seemingly on Ag/Ta) were flattened; this was rarely observed in the three-dimensional growth mode. Comparing Ag/Ta/glass with Ag/glass, we found that the Ta interlayer was effective in reducing both the resistance and the emissivity, accompanied by the relatively high transmittance in the visible region. In particular, Ag(9 nm)/Ta(1 nm)/glass film showed 0.08 of the emissivity, including ∼61% of the transmittance in the visible region (wavelength: 550 nm).

  8. The TA and TALE Experiments

    International Nuclear Information System (INIS)

    Thomson, Gordon

    2006-01-01

    The TA/TALE experiment is under construction, and is being deployed in Millard County, Utah. It will consist of a suite of detectors covering four orders of magnitude in energy, from 10 16.5 to 10 20.5 eV, and will observe cosmic ray showers with fluorescence detectors and arrays of scintillation counters. Events will be seen by multiple detectors and cross calibration of detectors' energy scales will be possible. TA/TALE will observe all three features of the spectrum of ultrahigh energy cosmic rays, observe the galactic/extragalactic transition, study the cosmology of cosmic ray sources, and perform anisotropy studies with unprecedented accuracy

  9. Ta(CNDipp){sub 6}. An isocyanide analogue of hexacarbonyltantalum(0)

    Energy Technology Data Exchange (ETDEWEB)

    Chakarawet, Khetpakorn; Long, Jeffrey R. [Department of Chemistry, University of California, Berkeley, CA (United States); Davis-Gilbert, Zachary W.; Harstad, Stephanie R.; Young, Victor G. Jr.; Ellis, John E. [Department of Chemistry, University of Minnesota, Minneapolis, MN (United States)

    2017-08-21

    Hexakis(2,6-diisopropylphenylisocyanide)tantalum is the first isocyanide analogue of the highly unstable Ta(CO){sub 6} and represents the only well-defined zerovalent tantalum complex to be prepared by conventional laboratory methods. Two prior examples of homoleptic Ta{sup 0} complexes are known, Ta(benzene){sub 2} and Ta(dmpe){sub 3}, dmpe=1,2-bis(dimethylphosphano)ethane, but these have only been accessed via ligand co-condensation with tantalum vapor in a sophisticated metal-atom reactor. Consistent with its 17-electron nature, Ta(CNDipp){sub 6} undergoes facile one-electron oxidation, reduction, or disproportionation reactions. In this sense, it qualitatively resembles V(CO){sub 6}, the only paramagnetic homoleptic metal carbonyl isolable under ambient conditions. (copyright 2017 Wiley-VCH Verlag GmbH and Co. KGaA, Weinheim)

  10. Proposal of guideline for bonding to prevention of hydrogen embrittlement at Ta/Zr bond interface. Hydrogen embrittlement in SUS304ULC/Ta/Zr explosive bonded joint

    International Nuclear Information System (INIS)

    Saida, Kazuyoshi; Fujimoto, Tetsuya; Nishimoto, Kazutoshi

    2010-01-01

    The occurrence condition of hydrogen embrittlement cracking at Ta/Zr bond interface was investigated with respect to the hydrogen content and applied stress in order to propose a guideline for the explosive bonding procedure to prevention of hydrogen embrittlement. Hydrogen charging test was conducted for SUS304ULC/Ta/Zr explosive bonded joints applied the different flexural strains. A hydrogen embrittlement crack occurred in the Zr substrate at Ta/Zr bond interface after hydrogen charging, and it was initiated at shorter charging times when the augmented strain was increased. The occurrence condition of hydrogen embrittlement cracking at Ta/Zr bond interface was shifted to lower stress and hydrogen content with an increase in the amount of explosive during bonding. It was suggested that hydrogen embrittlement in Ta/Zr explosive bonded joint could be inhibited by reducing the initial hydrogen content in Ta substrate less than approx. 5 ppm. (author)

  11. Thermal stability of TaN Schottky contacts on n-GaN

    Energy Technology Data Exchange (ETDEWEB)

    Hayes, J.R.; Kim, D-W.; Meidia, H.; Mahajan, S

    2003-02-07

    The thermal stability and electrical characteristics of tantalum-nitrogen alloy Schottky contacts on n-GaN were investigated. Non-stoichiometric {delta}-phase (40 atomic percent nitrogen) tantalum nitride contacts exhibited good electrical properties up to an annealing temperature of 600 deg. C. However, they degrade rapidly above this temperature due to outward diffusion of Ga and presumably nitrogen into the {delta}-phase tantalum nitride. It is surmised that excess Ta reacts with N at the GaN surface, freeing Ga which then diffuses into the TaN layer. Stoichiometric TaN Schottky contacts were stable at temperatures as high as 800 deg. C and had far superior electrical performance. This stems from the thermodynamic stability of the stoichiometric TaN/GaN interface. {delta}-phase TaN had I-V and C-V barrier heights of 0.55 eV and 0.8 eV respectively. On the other hand, TaN had an I-V barrier height near 0.7 eV and a C-V barrier height near 1.2 eV. The ideality factors for both {delta}-phase TaN and TaN were above 1.8 at all annealing temperatures, suggesting tunneling contributes significantly to current transport.

  12. Mutagenic activity of 2-(2',4'-diaminophenoxy)ethanol in strains TA1538 and TA98 of Salmonella typhimurium.

    Science.gov (United States)

    Mohn, G; Bouter, S; de Knijff, P

    1982-12-01

    The mutagenicity of 2-(2',4'-diaminophenoxy)ethanol (2,4-DAPE) was compared with that of 2,4-diaminoanisole (2,4-DAA), a chemically related compound previously used in hair-dye formulations. Both chemicals were tested in standard procedures with the Salmonella/microsome mutagenicity test as described by Ames and colleagues. In several experiments, which extended over a total period of 2 years, 2,4-DAA exhibited definite, but variable mutagenicity toward strain TA1538 when S9 preparations of rat liver induced with Aroclor 1254 were present in the incubation mixtures. The compound 2,4-DAPE did not exhibit detectable mutagenic activity when tested concomitantly under the same experimental conditions. We conclude that 2,4-DAPE is not mutagenic for Salmonella under conditions of the standard mammalian microsome assay with strain TA1538 and TA98 as indicators.

  13. Atomic resolution investigations of phase transformation from TaN to CrTaN in a steel matrix

    DEFF Research Database (Denmark)

    Danielsen, Hilmar Kjartansson; Hald, John

    2012-01-01

    strength of the steel. The Cr content promotes Z-phase precipitation, making MN strengthening of these materials unfeasible, since 12%Cr is necessary for oxidation resistance. The authors have suggested an acceleration of Z-phase precipitation to obtain a fine and stable distribution of CrMN instead of MN...... atoms diffuse from the steel matrix into TaN precipitates and physically transform them into CrTaN. The crystal structure of the precipitates changes from that of a typical MN NaCl type crystal structure to a Z-phase crystal structure with alternating double layers of Cr and TaN. Since there is a large......In development of 12%Cr high temperature steels used for fossil fired power plants, the precipitation of large Z-phase particles, CrMN, has been identified as a major problem since they replace small and finely distributed MN particles. This causes a premature breakdown in the longterm creep...

  14. Electrochemical lithium and sodium intercalation into the tantalum-rich layered chalcogenides Ta2Se and Ta2Te3

    International Nuclear Information System (INIS)

    Lavela, P.; Tirado, J.L.

    1999-01-01

    Two-layered tantalum chalcogenides are evaluated as alkali metal intercalation hosts in lithium and sodium electrochemical cells. The metal-rich pseudo-two-dimensional solid Ta 2 Se shows a poor intercalation behaviour. Lithium reacts with the selenide by deintercalating selenium from the blocks of Ta-related b.c.c. structure leading to a collapse of the structure and the formation of tantalum metal. Sodium is reversibly intercalated to a limited extent leading to complex structural changes in the selenide, as revealed by electron diffraction. The two-dimensional telluride Ta 2 Te 3 allows a topotactic intercalation of lithium below 1 F/mol, while a more extended reaction leads to sample amorphization. The better intercalation behaviour of this solid can be related with the one-atom thick metal layer and the van der Waals gap separating tellurium atoms of successive layers. Sodium can be reversibly intercalated into Ta 2 Te 3 in sodium cells which show a good cycling behaviour. Exposure of the intercalated solid to water vapour allows the preparation of hydrated products with a monolayer or a bilayer of water molecules solvating sodium in the interlayer space. (orig.)

  15. Efficient Visible-Light-Driven Z-Scheme Overall Water Splitting Using a MgTa2O(6-x)N(y)/TaON Heterostructure Photocatalyst for H2 Evolution.

    Science.gov (United States)

    Chen, Shanshan; Qi, Yu; Hisatomi, Takashi; Ding, Qian; Asai, Tomohiro; Li, Zheng; Ma, Su Su Khine; Zhang, Fuxiang; Domen, Kazunari; Li, Can

    2015-07-13

    An (oxy)nitride-based heterostructure for powdered Z-scheme overall water splitting is presented. Compared with the single MgTa2O(6-x)N(y) or TaON photocatalyst, a MgTa2O(6-x)N(y)/TaON heterostructure fabricated by a simple one-pot nitridation route was demonstrated to effectively suppress the recombination of carriers by efficient spatial charge separation and decreased defect density. By employing Pt-loaded MgTa2O(6-x)N(y)/TaON as a H2-evolving photocatalyst, a Z-scheme overall water splitting system with an apparent quantum efficiency (AQE) of 6.8% at 420 nm was constructed (PtO(x)-WO3 and IO3(-)/I(-) pairs were used as an O2-evolving photocatalyst and a redox mediator, respectively), the activity of which is circa 7 or 360 times of that using Pt-TaON or Pt-MgTa2O(6-x)N)y) as a H2-evolving photocatalyst, respectively. To the best of our knowledge, this is the highest AQE among the powdered Z-scheme overall water splitting systems ever reported. © 2015 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  16. Meltability in system of K2TaF7-NaF-NaCl-KCl

    International Nuclear Information System (INIS)

    Kartsev, V.E.; Kovalev, F.V.; Korshunov, B.G.

    1975-01-01

    Thermographic and visual-polythermal techniques were used to study the meltability in K 2 TaF 7 -NaF-NaCl-KCl system. The tetrahedron-forming sections NaF-NaCl-K 2 TaF 7 xKCl and NaF-K 2 TaF 7 xKCl-2K 2 TaF 7 xNaCl divide the concentration tetrahedron into three particular tetrahedra: NaF-K 2 TaF 7 xKCl-2K 2 TaF 7 xNaCl-K 2 TaF 7 , NaF-NaCl-K 2 TaF 7 xKCl-2K 2 TaF 7 xaCl, and NaF-NaCl-KCl-K 2 TaF 7 xKCl. Non-variant equilibrium points in all of the particular four-component systems have been determined

  17. Uzurpacija zemljišta : Land usurpation

    OpenAIRE

    Jusuf Topoljak; Admir Mulahusić

    2011-01-01

    Rad na temu „Uzurpacija zemljišta“ izlaže problematiku uzurpacije zemljišta u Bosni i Hercegovini. Velika je uloga geodezije u rješavanju ovakvog, za društvo kompleksnog problema. U radu su date naznake definisanja i rješavanja problema uzurpiranog zemljišta. : Work on the topic of "land usurpation," exposes the issue of land usurpation in Bosnia and Herzegovina. Geodesy has a very important role in solving such a complex problem for the whole society. In this paper are given hints of defin...

  18. New ternary tantalum borides containing boron dumbbells: Experimental and theoretical studies of Ta2OsB2 and TaRuB

    Science.gov (United States)

    Mbarki, Mohammed; Touzani, Rachid St.; Rehorn, Christian W. G.; Gladisch, Fabian C.; Fokwa, Boniface P. T.

    2016-10-01

    The new ternary transition metal-rich borides Ta2OsB2 and TaRuB have been successfully synthesized by arc-melting the elements in a water-cooled crucible under an argon atmosphere. The crystal structures of both compounds were solved by single-crystal X-ray diffraction and their metal compositions were confirmed by EDX analysis. It was found that Ta2OsB2 and TaRuB crystallize in the tetragonal Nb2OsB2 (space group P4/mnc, no. 128) and the orthorhombic NbRuB (space group Pmma, no. 51) structure types with lattice parameters a=5.878(2) Å, c=6.857(2) Å and a=10.806(2) Å, b=3.196(1) Å, c=6.312(2) Å, respectively. Furthermore, crystallographic, electronic and bonding characteristics have been studied by density functional theory (DFT). Electronic structure relaxation has confirmed the crystallographic parameters while COHP bonding analysis indicates that B2-dummbells are the strongest bonds in both compounds. Moreover, the formation of osmium dumbbells in Ta2OsB2 through a Peierls distortion along the c-axis, is found to be the origin of superstructure formation. Magnetic susceptibility measurements reveal that the two phases are Pauli paramagnets, thus confirming the theoretical DOS prediction of metallic character. Also hints of superconductivity are found in the two phases, however lack of single phase samples has prevented confirmation. Furthermore, the thermodynamic stability of the two modifications of AMB (A=Nb, Ta; M =Ru, Os) are studied using DFT, as new possible phases containing either B4- or B2-units are predicted, the former being the most thermodynamically stable modification.

  19. Evolution of resistive switching mechanism through H2O2 sensing by using TaOx-based material in W/Al2O3/TaOx/TiN structure

    Science.gov (United States)

    Chakrabarti, Somsubhra; Panja, Rajeswar; Roy, Sourav; Roy, Anisha; Samanta, Subhranu; Dutta, Mrinmoy; Ginnaram, Sreekanth; Maikap, Siddheswar; Cheng, Hsin-Ming; Tsai, Ling-Na; Chang, Ya-Ling; Mahapatra, Rajat; Jana, Debanjan; Qiu, Jian-Tai; Yang, Jer-Ren

    2018-03-01

    Understanding of resistive switching mechanism through H2O2 sensing and improvement of switching characteristics by using TaOx-based material in W/Al2O3/TaOx/TiN structure have been reported for the first time. Existence of amorphous Al2O3/TaOx layer in the RRAM devices has been confirmed by transmission electron microscopy. By analyzing the oxidation states of Ta2+/Ta5+ for TaOx switching material and W0/W6+ for WOx layer at the W/TaOx interface through X-ray photoelectron spectroscopy and H2O2 sensing, the reduction-oxidation mechanism under Set/Reset occurs only in the TaOx layer for the W/Al2O3/TaOx/TiN structures. This leads to higher Schottky barrier height at the W/Al2O3 interface (0.54 eV vs. 0.46 eV), higher resistance ratio, and long program/erase endurance of >108 cycles with 100 ns pulse width at a low operation current of 30 μA. Stable retention of more than 104 s at 85 °C is also obtained. Using conduction mechanism and reduction-oxidation reaction, current-voltage characteristic has been simulated. Both TaOx and WOx membranes have high pH sensitivity values of 47.65 mV/pH and 49.25 mV/pH, respectively. Those membranes can also sense H2O2 with a low concentration of 1 nM in an electrolyte-insulator-semiconductor structure because of catalytic activity, while the Al2O3 membrane does not show sensing. The TaOx material in W/Al2O3/TaOx/TiN structure does not show only a path towards high dense, small size memory application with understanding of switching mechanism but also can be used for H2O2 sensors.

  20. Laminated structure in internally oxidized Ru-Ta coatings

    Energy Technology Data Exchange (ETDEWEB)

    Chen, Yung-I, E-mail: yichen@mail.ntou.edu.tw

    2012-12-01

    During the development of refractory alloy coatings for protective purposes at high temperature under oxygen-containing atmospheres, previous studies noted and examined the internal oxidation phenomenon for Mo-Ru and Ru-Ta coatings. The internally oxidized zone shows a laminated structure, consisting of alternating oxygen-rich and deficient layers stacked with a general orientation. Previous studies proposed a forming mechanism. To investigate in detail, Ru-Ta coatings were prepared with various rotating speeds of a substrate-holder. The coatings were annealed at 600 Degree-Sign C in an atmosphere continuously purged with 1% O{sub 2}-99% Ar mixed gas for 30 min. Transmission electron microscopy was used to examine the laminated-layer periods. Auger electron spectroscopy depth profiles certified the periodical variation of the related constituents. X-ray photoelectron spectroscopy proved the valence variation of Ta in the near surface, accompanied by the introduction of oxygen ions. The inward diffusion of oxygen was dominated by lattice diffusion. - Highlights: Black-Right-Pointing-Pointer Laminated Ru-Ta coatings consisted of a cyclical gradient concentration. Black-Right-Pointing-Pointer The as-deposited coatings showed a laminated structure with a period of 4-34 nm. Black-Right-Pointing-Pointer Internal oxidation of Ru-Ta coatings executed after annealing in 1% O{sub 2}-Ar atmosphere. Black-Right-Pointing-Pointer Oxygen inward diffusion was dominated by lattice diffusion.

  1. Ta4AlC3: Phase determination, polymorphism and deformation

    International Nuclear Information System (INIS)

    Eklund, P.; Palmquist, J.-P.; Hoewing, J.; Trinh, D.H.; El-Raghy, T.; Hoegberg, H.; Hultman, L.

    2007-01-01

    Ta 4 AlC 3 , a new member of the M n+1 AX n -phase family, has been synthesized and characterized (n = 1-3; M = early transition metal; A A-group element; and X = C and/or N). Phase determination by Rietveld refinement of synchrotron X-ray diffraction data shows that Ta 4 AlC 3 belongs to the P6 3 /mmc space group with a and c lattice parameters of 3.10884 ± 0.00004 A and 24.0776 ± 0.0004 A, respectively. This is shown to be the α-polymorph of Ta 4 AlC 3 , with the same structure as Ti 4 AlN 3 . Lattice imaging by high-resolution transmission electron microscopy demonstrates the characteristic MAX-phase stacking of α-Ta 4 AlC 3 . Three modes of mechanical deformation of α-Ta 4 AlC 3 are observed: lattice bending, kinking and delamination

  2. The TaSST: Tactile Sleeve for Social Touch

    NARCIS (Netherlands)

    Huisman, G.; Darriba Frederiks, A.; van Dijk, B.; Heylen, D.; Kröse, B.

    2013-01-01

    In this paper we outline the design process of the TaSST (Tactile Sleeve for Social Touch), a touch-sensitive vibrotactile arm sleeve. The TaSST was designed to enable two people to communicate different types of touch over a distance. The touch-sensitive surface of the sleeve consists of a grid of

  3. The TaSST: Tactile sleeve for social touch

    NARCIS (Netherlands)

    Huisman, Gijs; Darriba Frederiks, Aduén; van Dijk, Elisabeth M.A.G.; Heylen, Dirk K.J.; Krose, Ben

    In this paper we outline the design process of the TaSST (Tactile Sleeve for Social Touch), a touch-sensitive vibrotactile arm sleeve. The TaSST was designed to enable two people to communicate different types of touch over a distance. The touch-sensitive surface of the sleeve consists of a grid of

  4. The TaSST - Tactile Sleeve for Social Touch

    NARCIS (Netherlands)

    Huisman, Gijs; Darriba Frederiks, Aduén; Van Dijk, Betsy; Heylen, Dirk

    2013-01-01

    In this paper we outline the design process of TaSST (Tactile Sleeve for Social Touch), a touch-sensitive vibrotactile arm sleeve. The TaSST was designed to enable two people to communicate different types of touches over a distance. The touch-sensitive surface of the sleeve consists of a grid of

  5. 76 FR 50739 - Hung Ta Fan: Debarment Order

    Science.gov (United States)

    2011-08-16

    ...] Hung Ta Fan: Debarment Order AGENCY: Food and Drug Administration, HHS. ACTION: Notice. SUMMARY: The... (the FD&C Act) debarring Hung Ta Fan for a period of 5 years from importing articles of food or.... Fan was convicted of a felony under Federal law for conduct relating to the importation into the...

  6. FLEKSIGURNOST I (DEREGULACIJA TRŽIŠTA RADA

    Directory of Open Access Journals (Sweden)

    Sandra Laleta

    2016-01-01

    Full Text Available Predmet su ovoga rada radni odnosi i tržište rada u kontekstu fleksigurnosti. U radu se analizira novi vladavinski model, soft law, otvorene metode koordina- cije, europski socijalni model, inkluzivnost, kategorije koje su neraskidivo vezane uz fleksigurnost, radne odnose i tržište rada. Istražena su njihova obilježja i utjecaj na supranacionalnu regulativu, usporednopravna i hrvatska rješenja. Daje se i raščlamba nekih novih instituta tržišta rada (novi oblici uređenja radnog vremena, agencijski rad, mini-jobs. Poseban dio rada čini istraživanje (dereguliranja tržišta rada, novih modela zapošljavanja, kao i fleksigurnosti i hrvatskoga tržišta rada de lege lata te se daju prijedlozi de lege ferenda.

  7. The potential capacities of Ta'ziyeh in Modern Imagism

    Directory of Open Access Journals (Sweden)

    A.M Nedai

    2009-03-01

    Full Text Available Ta'ziyeh as the most important method in religious and ritual theatre in Iran has many capabilities which can be used in modern visualization. The only element in this theatre which has been studied is distancing in performance styles. But by studying the existent versions of Ta'ziyehs, there are other elements for recognition and use, which has not still been studied. The relationship between religious and ritual theatre with Ta'ziyeh and also their main themes helps to identify these elements and their capabilities. Meanwhile, the presence of music as an expressive and performing element provides a basis which can be used in finding a new manner of expression in visual/dramatic works (such as music videos. Studying on such elements as time-place interlace, character replacement, functions of music, and their effects on audiences, shows that Ta'ziyeh has specific capabilities in visualization (even in Cinema and Media. This article, through capitalizing on this subject and introducing one paradigm (Moses and poor Pilgrim, and comparing two versions of it, tries to represent these capabilities, and illuminates Ta'ziyeh's abilities for modern (and even postmodern visualization.

  8. Electric conductivity of salt melts containing KCL, KF and K2TaF7

    International Nuclear Information System (INIS)

    Agulyanskij, A.I.; Stangrit, P.T.; Konstantinov, V.I.

    1978-01-01

    Given are electric conductivity measurement results depending on the temperature and composition of the molten KF-K 2 TaF 7 , KCl-K 2 TaF 7 systems and also melts close in their composition to industrial electrolytes, KCl-KF (in mass ratio of 2:1) with addition of K 2 TaF 7 up to 25 mass%. Presented are electric conductivity molecular isotherms of the KF-K 2 TaF 7 , KCl-K 2 TaF 7 systems at 800 deg C and specific electric conductivity dependence of KCl-KF-K 2 TaF 7 melts on K 2 TaF 7 composition at 800 deg C and 900 deg C. Proceeding from the shape of molecular and specific electric conductivity isotherms a conclusion is made about existence of the following tantalum-containing ions: TaF 7 2- , TaF 6 - and TaF 6 Cl 2- in the investigated melts

  9. Spectroscopy of 169Ta

    International Nuclear Information System (INIS)

    Kshetri, Ritesh; Ray, I.; Ganguly, S.; Pradhan, M.K.; Raut, R.; Goswami, A.; Banerjee, P.; Mukherjee, A.; Datta Pramanik, U.; Bhattacharya, S.; Dasmahapatra, B.; Saha Sarkar, M.; Dey, G.; Ray Basu, M.; Krishichayan; Chakraborty, A.; Ghugre, S.S.; Ray, M.; Sarkar, S.

    2006-01-01

    The lifetimes of the isomeric levels of 169,171 Ta have been re-measured using the centroid shift method of electronic timing technique. Preliminary results for lifetimes are in good agreement with the adopted values. Investigations are being carried out to identify other isomeric levels

  10. Microstructural characterization of Ta-Si alloy as cast; Caracterizacao microestrutural de ligas Ta-Si no estado bruto de fusao

    Energy Technology Data Exchange (ETDEWEB)

    Silva, A.A.A.P. da; Coelho, G.C.; Nunes, C.A.; Suzuki, P.A.; Borges, S.P.T., E-mail: antonioaaps@gmail.co [Universidade de Sao Paulo (EEL/USP), Lorena, SP (Brazil). Escola de Engenharia; Faria, M.I.S.T. [Centro Universitario de Volta Redonda (UNIFOA), RJ (Brazil)

    2010-07-01

    Recent experimental studies developed in our group involving systems containing transition metals and silicon differed from the phase diagrams actually accepted. The objective of this study is to experimentally re-evaluate the invariant reactions involving liquid phase of the binary Ta-Si. Samples with different compositions were melted in arc furnace with non-consumable tungsten electrode in the copper crucible cooled water under argon atmosphere and titanium getter, using materials of high purity (minimum purity of 99.5% Ta and 99.999% Si). The samples were melted four times to ensure the microstructural and compositional homogeneity. The microstructures of the samples as cast were characterized by scanning electron microscopy (SEM/EDS) and X-ray diffraction (XRD). The results of this analysis led to a proposal for the phase diagram of Ta-Si slightly different than the diagram currently accepted. (author)

  11. Using the TA to Prepare Graduate Students for Research and Employment

    Science.gov (United States)

    Heller, Kenneth

    One of the most underused components of the physics graduate program is the time spent being a teaching assistant (TA). Often the TA duties consist of grading and trying to help undergraduates survive a physics course. How those duties are accomplished is left to each TA. The most common TA preparation, if it exists, has a narrow focus on the class being taught. Preparation consists of describing, or perhaps practicing, specific teaching skills and gaining familiarity with the equipment used in the laboratory portion of the class. Instead TAs can be integrated into the entire course in which they function so that they learn the course as a system. This means treating a course in the same way one approaches a research project with the TAs as members of the research team headed by a faculty advisor. TA preparation is broadened and support includes the management, teamwork, and communication skills necessary. This makes the TAs more efficient and effective teachers while explicitly connecting the TA experience to the ``soft'' skills they need in their own research careers whether in industry, national laboratories, or academia. This talk describes such a program, functioning for over 20 years at the University of Minnesota, that takes no more time than the usual TA but results in graduate students that are more satisfied with their TA experience, are better prepared to function in research groups, and provide a better classroom experience for their undergraduate students.

  12. Chemical Concentrations in Field Mice from Open-Detonation Firing Sites TA-36 Minie and TA-39 Point 6 at Los Alamos National Laboratory

    Energy Technology Data Exchange (ETDEWEB)

    Fresquez, Philip R. [Los Alamos National Laboratory

    2011-01-01

    Field mice (mostly Peromyscus spp.) were collected at two open-detonation (high explosive) firing sites - Minie at Technical Area (TA) 36 and Point 6 at TA-39 - at Los Alamos National Laboratory in August of 2010 and in February of 2011 for chemical analysis. Samples of whole body field mice from both sites were analyzed for target analyte list elements (mostly metals), dioxin/furans, polychlorinated biphenyl congeners, high explosives, and perchlorate. In addition, uranium isotopes were analyzed in a composite sample collected from TA-36 Minie. In general, all constituents, with the exception of lead at TA-39 Point 6, in whole body field mice samples collected from these two open-detonation firing sites were either not detected or they were detected below regional statistical reference levels (99% confidence level), biota dose screening levels, and/or soil ecological chemical screening levels. The amount of lead in field mice tissue collected from TA-39 Point 6 was higher than regional background, and some lead levels in the soil were higher than the ecological screening level for the field mouse; however, these levels are not expected to affect the viability of the populations over the site as a whole.

  13. Bixbyite-type phases in the system Ta-Zr-O-N

    Energy Technology Data Exchange (ETDEWEB)

    Luedtke, Tobias; Orthmann, Steven; Lerch, Martin [Technische Univ. Berlin (Germany). Inst. fuer Chemie

    2017-06-01

    Phase-pure tantalum/zirconium oxide nitrides and nitrides were synthesized by the ammonolysis of amorphous oxide precursors. The nitrogen-rich oxide nitrides with variable anion composition and the nitride TaZrN3 crystallize in the cubic bixbyite-type structure (space group Ia3). The nitrogen content of these compounds has a significant influence on the cell parameters, the atomic positions, and the optical band gap. The results extend the already well-studied Ta-Zr-O-N system by new oxide nitrides in addition to the already known baddeleyite- and anosovite-type phases. TaZrN{sub 3} can be considered as a thermodynamically stable ternary variant of metastable Ta{sub 2}N{sub 3}.

  14. Study on mutual diffusion and phase diagram in the Ni-Ta system

    International Nuclear Information System (INIS)

    Pimenov, V.N.; Ugaste, Yu.Eh.; Akkushkarova, K.A.

    1977-01-01

    The mutual diffusion in the Ni-Ta system has been investigated with a view of refining the constitutional diagram. The mutual diffusion factors and their effective values in the various phases and the diffusion activation energies are calculated. Given are the dependences of the phase growth constants and the mutual diffusion factors upon the temperature. The existence of five new phases Ta 2 Ni, TaNi, TaNi 2 , TaNi 3 , TaNi 8 has been discovered in the range of temperatures between 1150 and 1300 deg C. It is established that all the phases have a small concentration range of existence. It is noted that the diffusion characteristics in the phases (mutual diffusion factor and activation energy) differ widely, but fail to correlate with their melting points

  15. Experimental investigation of phase equilibria in the Nb-Si-Ta ternary system

    Energy Technology Data Exchange (ETDEWEB)

    Li, Jian; Wang, Cuiping; Yao, Jun; Yang, Shuiyuan; Zhan Shi; Liu, Xingjun [Xiamen Univ. (China). Dept. of Materials Science and Engineering; Xiamen Univ. (China). Fujian Provincial Key Laboratory of Materials Genome; Kang, Yongwang [Beijing Institute of Aeronautical Materials (China). Science and Technology on Advanced High Temperature Structural Materials Lab.

    2016-12-15

    The phase equilibria in the Nb-Si-Ta ternary system at 1 373 K, 1 473 K and 1 573 K were investigated by means of back-scattered electron imaging, electron probe microanalysis and X-ray diffraction. The isothermal sections at 1 373 K, 1 473 K and 1 573 K consist of two three-phase regions and seven two-phase regions, without any ternary compounds. The compounds of NbSi{sub 2} and TaSi{sub 2}, αNb{sub 5}Si{sub 3} and αTa{sub 5}Si{sub 3} form continuous solid solutions, respectively. The solubilities of Nb in Ta{sub 3}Si and Ta{sub 2}Si phases are extremely large, whereas the solubility of Si in the β(Nb, Ta) phase is relatively small.

  16. Uzurpacija zemljišta : Land usurpation

    Directory of Open Access Journals (Sweden)

    Jusuf Topoljak

    2011-12-01

    Full Text Available Rad na temu „Uzurpacija zemljišta“ izlaže problematiku uzurpacije zemljišta u Bosni i Hercegovini. Velika je uloga geodezije u rješavanju ovakvog, za društvo kompleksnog problema. U radu su date naznake definisanja i rješavanja problema uzurpiranog zemljišta. : Work on the topic of "land usurpation," exposes the issue of land usurpation in Bosnia and Herzegovina. Geodesy has a very important role in solving such a complex problem for the whole society. In this paper are given hints of defining and solving the problem of land usurpation.

  17. A tunnelling study on polymer/1T-LixTaS2 layered nanocomposites

    International Nuclear Information System (INIS)

    Enomoto, Hiroyuki; Takai, Hiroyuki; Ozaki, Hajime; Lerner, Michael M

    2004-01-01

    Electronic structures near the Fermi level of polymer/1T-Li x TaS 2 layered nanocomposites have been studied by tunnelling spectroscopy. Polymer/1T-Li x TaS 2 layered nanocomposites were synthesized by using the exfoliation-adsorption technique. Single crystals of 1T-TaS 2 were used as host materials. Poly(ethylene oxide) (PEO) and poly(ethylenimine) (PEI) with different molecular weights were adopted as guest intercalants. Powder x-ray diffraction patterns showed that all samples of the polymer/1T-Li x TaS 2 layered nanocomposites contain organic polymer between all individual 1T-TaS 2 sheets. Although 1T-TaS 2 single crystal is well known to show quite unique temperature dependences of the resistivity due to the charge density wave (CDW), the resistivities of all polymer/1T-Li x TaS 2 nanocomposites showed semiconductor-like temperature dependences. The tunnelling spectra of polymer/1T-Li x TaS 2 nanocomposites revealed that the CDW gap disappears in the density of states near the Fermi level of polymer/1T-Li x TaS 2 nanocomposites and their electronic structures show a metallic behaviour

  18. TaER Expression Is Associated with Transpiration Efficiency Traits and Yield in Bread Wheat.

    Science.gov (United States)

    Zheng, Jiacheng; Yang, Zhiyuan; Madgwick, Pippa J; Carmo-Silva, Elizabete; Parry, Martin A J; Hu, Yin-Gang

    2015-01-01

    ERECTA encodes a receptor-like kinase and is proposed as a candidate for determining transpiration efficiency of plants. Two genes homologous to ERECTA in Arabidopsis were identified on chromosomes 6 (TaER2) and 7 (TaER1) of bread wheat (Triticum aestivum L.), with copies of each gene on the A, B and D genomes of wheat. Similar expression patterns were observed for TaER1 and TaER2 with relatively higher expression of TaER1 in flag leaves of wheat at heading (Z55) and grain-filling (Z73) stages. Significant variations were found in the expression levels of both TaER1 and TaER2 in the flag leaves at both growth stages among 48 diverse bread wheat varieties. Based on the expression of TaER1 and TaER2, the 48 wheat varieties could be classified into three groups having high (5 varieties), medium (27 varieties) and low (16 varieties) levels of TaER expression. Significant differences were also observed between the three groups varying for TaER expression for several transpiration efficiency (TE)- related traits, including stomatal density (SD), transpiration rate, photosynthetic rate (A), instant water use efficiency (WUEi) and carbon isotope discrimination (CID), and yield traits of biomass production plant-1 (BYPP) and grain yield plant-1 (GYPP). Correlation analysis revealed that the expression of TaER1 and TaER2 at the two growth stages was significantly and negatively associated with SD (Ptranspiration rate (Ptranspiration efficiency -related traits and yield in bread wheat, implying a function for TaER in regulating leaf development of bread wheat and contributing to expression of these traits. Moreover, the results indicate that TaER could be exploitable for manipulating important agronomical traits in wheat improvement.

  19. 75 FR 66794 - Notice of Affirmative Determination Regarding Application for Reconsideration: TA-W-71,572...

    Science.gov (United States)

    2010-10-29

    ... DEPARTMENT OF LABOR Employment and Training Administration [TA-W-71,572; TA-W-71,572A; TA-W-71,572B; TA-W-71,572C] Notice of Affirmative Determination Regarding Application for Reconsideration: TA-W...; TA-W-71,572A, Severstal Wheeling, Inc., a Subsidiary of Severstal North America, Inc., Yorkville, OH...

  20. Atomistic simulation of the point defects in TaW ordered alloy

    Indian Academy of Sciences (India)

    atom method (MAEAM), the formation, migration and activation energies of the point defects for six-kind migration mechanisms in B2-type TaW alloy have been investigated. The results showed that the anti-site defects TaW and WTa were easier to form than Ta and W vacancies owing to their lower formation energies.

  1. Mechanism of n-butane hydrogenolysis promoted by Ta-hydrides supported on silica

    KAUST Repository

    Pasha, Farhan Ahmad

    2014-06-06

    The mechanism of hydrogenolysis of alkanes, promoted by Ta-hydrides supported on silica via 2 ≡ Si-O- bonds, has been studied with a density functional theory (DFT) approach. Our study suggests that the initial monohydride (≡ Si-O-)2Ta(III)H is rapidly trapped by molecular hydrogen to form the more stable tris-hydride (≡ Si-O-) 2Ta(V)H3. Loading of n-butane to the Ta-center occurs through C-H activation concerted with elimination of molecular hydrogen (σ-bond metathesis). Once the Ta-alkyl species is formed, the C-C activation step corresponds to a β-alkyl transfer to the metal with elimination of an olefin. According to these calculations, an α-alkyl transfer to the metal to form a Ta-carbene species is of higher energy. The olefins formed during the C-C activation step can be rapidly hydrogenated by both mono- and tris-Ta-hydride species, making the overall process of alkane cracking thermodynamically favored. © 2014 American Chemical Society.

  2. Superconducting state in (W, Ta)5SiB2

    Science.gov (United States)

    Fukuma, M.; Kawashima, K.; Akimitsu, J.

    We characterize the superconducting state in a boro-silicide (W, Ta)5SiB2, with Tc of 6.5 K by means of magnetization, electrical resistivity, and specific heat measurements. As x increased, the transition temperature Tc abruptly enhances from 5.8 to 6.5 K. The magnetization versus magnetic field (M-H) curve indicated that (W, Ta)5SiB2 was a conventional type-II superconductor. The estimated lower critical field Hc1(0) and upper critical field Hc2(T) are about 121 Oe and 14.7 kOe, respectively. The penetration depth λ(0) and coherence length ξ(0) are calculated to be approximately 369 and 14.9 nm, respectively, using Ginzburg-Landau (GL) equations. Specific heat data shows the superconductivity in W4.5Ta0.5SiB2 belongs to a week-coupling BCS superconductor. Finally, we discuss the increasing of Tc in of (W, Ta)5SiB2 system.

  3. Tritium diffusion in V, Nb and Ta

    International Nuclear Information System (INIS)

    Qi, Z.; Voelkl, J.; Laesser, R.; Wenzl, H.

    1983-01-01

    Gorsky-effect measurements of the diffusion coefficient of tritium (T) in V, Nb and Ta are reported. The measurements were performed at small T concentrations (less than about 1.4 at%), and in the temperature range from -140 0 C to 100 0 C. Comparison with results obtained for H and D shows an increase of the activation energy with increasing isotopic mass. For Nb and Ta, the pre-exponential factors are identical for all the isotopes, whereas for V this factor is appreciably larger for T than for H and D. The reduction of the relaxation strength in the presence of precipitation allows a rough determination of the solubility limit, which is found to be isotope independent for Nb and Ta. In V, the solubility limit for T is shifted slightly to lower temperatures. The H, D or T induced lattice expansion calculated from the relaxation strength shows no dependence on isotopic mass. (author)

  4. Promising Ta-Ti-Zr-Si metallic glass coating without cytotoxic elements for bio-implant applications

    Science.gov (United States)

    Lai, J. J.; Lin, Y. S.; Chang, C. H.; Wei, T. Y.; Huang, J. C.; Liao, Z. X.; Lin, C. H.; Chen, C. H.

    2018-01-01

    Tantalum (Ta) is considered as one of the most promising metal due to its high corrosion resistance, excellent biocompatibility and cell adhesion/in-growth capabilities. Although there are some researches exploring the biomedical aspects of Ta and Ta based alloys, systematic characterizations of newly developed Ta-based metallic glasses in bio-implant applications is still lacking. This study employs sputtering approach to produced thin-film Ti-based metallic glasses due to the high melting temperature of Ta (3020 °C). Two fully amorphous Ta-based metallic glasses composed of Ta57Ti17Zr15Si11 and Ta75Ti10Zr8Si7 are produced and experimentally characterized in terms of their mechanical properties, bio-corrosion properties, surface hydrophilic characteristics, and in-vitro cell viability and cells attachment tests. Compare to conventional pure Ti and Ta metals, the developed Ta-based metallic glasses exhibit higher hardness and lower modulus which are better match to the mechanical properties of bone. MTS assay results show that Ta-based metallic glasses show comparable cell viability and cell attachment rate compared to that of pure Ti and Ta surface in a 72 h in-vitro test.

  5. Low-Level, Measured Response of Los Alamos National Laboratories TA 16 - Building 411 and TA 8 - Building 23 to Direct Flash Attachment of Lightning

    International Nuclear Information System (INIS)

    Dinallo, Michael A.; Holmes, Parris; Merewether, Kimball O.; Morris, Marvin E.

    1999-01-01

    On September 24, 25, 28, and 29, 1998 and on October 19 and 23, 1998, transfer impedance measurements were made on Los Alamos National Laboratories TA 16 - Building 411 and TA 8-- Building 23 to characterize their interior open-circuit voltage response to a direct lightning flash attachment to the structures. The theory, history, measurement methods and equipment, and specific measured results are detailed. The measured results demonstrate that if the remaining metallic penetrations are bonded, then the rebar of the two structures is sufficiently well connected to form a Faraday cage that reduces the maximum open-circuit voltage inside the structure to a sufficiently low level that the required standoff distance to prevent arcing to explosive assemblies is 6.8 inches for TA 16 - Building 411 and is 11.5 inches for TA 8 - Building 23

  6. More Thoughts on the Mycenaean ta-ra-si-ja system

    DEFF Research Database (Denmark)

    Nosch, Marie-Louise Bech

    2006-01-01

    Discussion of the position of the Mycenaean ta-ra-si-ja system between fiscality and obligatory work......Discussion of the position of the Mycenaean ta-ra-si-ja system between fiscality and obligatory work...

  7. High temperature oxidation resistance of (Ti,Ta)(C,N)-based cermets

    International Nuclear Information System (INIS)

    Chicardi, E.; Córdoba, J.M.; Gotor, F.J.

    2016-01-01

    Highlights: • Cermets based on (Ti,Ta)(C,N) were oxidized in air between 800 and 1100 °C for 48 h. • The substitution of Ti by Ta resulted in a high resistance to oxidation. • A protective layer of cobalt titanates at the surface of cermets was observed. • A rutile phase in which some Ti"4"+ are replaced by Ta"5"+ was detected. • This replacement decelerated the oxygen diffusion into the cermets. - Abstract: Cermets based on titanium–tantalum carbonitride were oxidized in static air between 800 °C and 1100 °C for 48 h. The thermogravimetric and microstructural study showed an outstanding reduction in the oxidation of more than 90% when the Ta content was increased. In cermets with low Ta content, the formation of a thin CoO/Co_3O_4 outer layer tends to disappear by reacting with the underlying rutile phase, which emerges at the surface. However, in cermets with higher Ta content, the formation of an external titanate layer, observed even at a low temperature, appears to prevent the oxygen diffusion and the oxidation progression.

  8. Scanning tunneling microscopy of atoms and charge density waves in 1T-TaS2, 1T-TaSe2 and 1T-VSe2

    International Nuclear Information System (INIS)

    Slough, G.; Giambattista, B.; Johnson, A.; McNairy, W.W.; Coleman, R.V.

    1988-01-01

    The layer structure dichalcogenide materials TaS 2 and TaSe 2 grow in several different phases depending on the coordination between the Ta and chalcogenide atoms and the number of three layer sandwiches per unit cell. The 1T phase has octahedral coordination between the Ta and chalcogenide atoms and has one three layer sandwich per unit cell. The high temperature Fermi surfaces (FSs) of the 1T phase Ta based materials exhibit a favorable nesting condition and undergo a charge-density-wave (CDW) transition at temperatures well above room temperature. At low temperatures the CDWs form a √13 /ovr string/a /times/ √13 a commensurate superlattice. STM scans on the 1T phases confirm the presence of an extremely strong CDW modulation inducing z-deflections in the constant current mode of anomalously large values. 1T-VSe 2 is also a member of the VB layer structure dichalcogenide group and band structure calculations show the high temperatures FS to be similar to that of 1T-TaSe 2 . However, sufficient differences exist such that the CDW formation is quite different. The CDW superlattice is observed to form only below room temperature and locks into a 4/ovr string/a /times/ 4/ovr string/a superlattice below /approximately/80K rather than the √13 /ovr string/a /times/ √13 /ovr string/a one observed in 1T-TaSe 2 . Based on electron and neutron diffraction results on stoichiometric 1T-VSe 2 two phase transitions are detected, a second order transition at 110K and a first order transition at /approximately/80K. 20 figs

  9. The hyperfine fields at 181Ta in HfFe2

    International Nuclear Information System (INIS)

    Cekic, B.; Ivanovic, N.; Manasijevic, M.; Koicki, S.; Koteski, V.; Cavor, J.; Radisavljevic, I.; Milosevic, Z.; Novakovic, N.

    2001-01-01

    The hyperfine fields (HFF) in the polycrystalline HfFe 2 binary compound consisting the two various phases MgCu 2 and MgZn 2 , were measured at 181 Ta probe ion sites by gamma-gamma time differential perturbed angular correlations (TDPAC) technique in a wide temperature range. The origin of the hyperfine magnetic field is discussed taking in account the coordination of the 181 Ta probe ion, its core polarization and the polarization of conduction electrons around the 181 Ta site in both phases. (author)

  10. Mechanism of n-butane hydrogenolysis promoted by Ta-hydrides supported on silica

    KAUST Repository

    Pasha, Farhan Ahmad; Cavallo, Luigi; Basset, Jean-Marie

    2014-01-01

    (III)H is rapidly trapped by molecular hydrogen to form the more stable tris-hydride (≡ Si-O-) 2Ta(V)H3. Loading of n-butane to the Ta-center occurs through C-H activation concerted with elimination of molecular hydrogen (σ-bond metathesis). Once the Ta

  11. Diffusion barrier performance of novel Ti/TaN double layers for Cu metallization

    International Nuclear Information System (INIS)

    Zhou, Y.M.; He, M.Z.; Xie, Z.

    2014-01-01

    Highlights: • Novel Ti/TaN double layers offering good stability as a barrier against Cu metallization have been made achievable by annealing in vacuum. • The Ti/TaN double layers improved the adhesion with Cu thin films and showed good diffusion barrier between Cu and SiO 2 /Si up to the annealing condition. • The failure mechanism of Ti/TaN bi-layer is similar with the Cu/TaN/Si metallization system in which Cu atoms diffuse through the grain boundary of barrier and react with silicon to form Cu 3 Si. - Abstract: Novel Ti/TaN double layers offering good stability as a barrier against Cu metallization have been made achievable by annealing in vacuum better than 1 × 10 −3 Pa. Ti/TaN double layers were formed on SiO 2 /Si substrates by DC magnetron sputtering and then the properties of Cu/Ti/TaN/SiO 2 /Si film stacks were studied. It was found that the Ti/TaN double layers provide good diffusion barrier between Cu and SiO 2 /Si up to 750 °C for 30 min. The XRD, Auger and EDS results show that the Cu–Si compounds like Cu 3 Si were formed by Cu diffusion through Ti/TaN barrier for the 800 °C annealed samples. It seems that the improved diffusion barrier property of Cu/Ti/TaN/SiO 2 /Si stack is due to the diffusion of nitrogen along the grain boundaries in Ti layer, which would decrease the defects in Ti film and block the diffusion path for Cu diffusion with increasing annealing temperature. The failure mechanism of Ti/TaN bi-layer is similar to the Cu/TaN/Si metallization system in which Cu atoms diffuse through the grain boundary of barrier and react with silicon to form Cu 3 Si

  12. Emerging good practices for Translatability Assessment (TA) of Patient-Reported Outcome (PRO) measures.

    Science.gov (United States)

    Acquadro, Catherine; Patrick, Donald L; Eremenco, Sonya; Martin, Mona L; Kuliś, Dagmara; Correia, Helena; Conway, Katrin

    2017-01-01

    This paper presents emerging Good Practices for Translatability Assessment (TA) of Patient-Reported Outcome (PRO) Measures. The ISOQOL Translation and Cultural Adaptation Special Interest Group (TCA-SIG) undertook the review of several TA approaches, with the collaboration of organizations who are involved in conducting TA, and members of the TCA-SIG. The effort led to agreement by the writing group on Good Practices for 1) the terminology to be used in referring to translatability process, 2) the best definition of TA, 3) the methodology that is recommended at each step of the process, 4) the persons involved in TA, 5) the timing of assessment, 6) the review criteria for TA, and 7) the recommendations to be made at the end of the TA process. With input from the TCA-SIG membership and in consultation with experts in the field, these emerging good practices can guide the future use of TA in the development of PROs.

  13. Supporting data for senary refractory high-entropy alloy CrxMoNbTaVW

    Directory of Open Access Journals (Sweden)

    B. Zhang

    2015-12-01

    Full Text Available This data article is related to the research paper entitled “senary refractory high-entropy alloy CrxMoNbTaVW [1]”. In this data article, the pseudo-binary Cr-MoNbTaVW phase diagram is presented to show the impact of Cr content to the senary Cr-MoNbTaVW alloy system; the sub-lattice site fractions are presented to show the disordered property of the Cr-MoNbTaVW BCC structures; the equilibrium and Scheil solidification results with the actual sample elemental compositions are presented to show the thermodynamic information of the melted/solidified CrxMoNbTaVW samples; and the raw EDS scan data of the arc-melted CrxMoNbTaVW samples are also provided.

  14. Correlation between the transport mechanisms in conductive filaments inside Ta2O5-based resistive switching devices and in substoichiometric TaOx thin films

    Science.gov (United States)

    Rosário, Carlos M. M.; Thöner, Bo; Schönhals, Alexander; Menzel, Stephan; Wuttig, Matthias; Waser, Rainer; Sobolev, Nikolai A.; Wouters, Dirk J.

    2018-05-01

    Conductive filaments play a key role in redox-based resistive random access memory (ReRAM) devices based on the valence change mechanism, where the change of the resistance is ascribed to the modulation of the oxygen content in a local region of these conductive filaments. However, a deep understanding of the filaments' composition and structure is still a matter of debate. We approached the problem by comparing the electronic transport, at temperatures from 300 K down to 2 K, in the filaments and in TaOx films exhibiting a substoichiometric oxygen content. The filaments were created in Ta (15 nm)/Ta2O5 (5 nm)/Pt crossbar ReRAM structures. In the TaOx thin films with various oxygen contents, the in-plane transport was studied. There is a close similarity between the electrical properties of the conductive filaments in the ReRAM devices and of the TaOx films with x ˜ 1, evidencing also no dimensionality difference for the electrical transport. More specifically, for both systems there are two different conduction processes: one in the higher temperature range (from 50 K up to ˜300 K), where the conductivity follows a √{ T } dependence, and one at lower temperatures (<50 K), where the conductivity follows the exp(-1 / √{ T } ) dependence. This suggests a strong similarity between the material composition and structure of the filaments and those of the substoichiometric TaOx films. We also discuss the temperature dependence of the conductivity in the framework of possible transport mechanisms, mainly of those normally observed for granular metals.

  15. K(3)TaF(8) from laboratory X-ray powder data.

    Science.gov (United States)

    Smrcok, Lubomír; Cerný, Radovan; Boca, Miroslav; Macková, Iveta; Kubíková, Blanka

    2010-02-01

    The crystal structure of tripotassium octafluoridotantalate, K(3)TaF(8), determined from laboratory powder diffraction data by the simulated annealing method and refined by total energy minimization in the solid state, is built from discrete potassium cations, fluoride anions and monocapped trigonal-prismatic [TaF(7)](2-) ions. All six atoms in the asymmetric unit are in special positions of the P6(3)mc space group: the Ta and one F atom in the 2b (3m) sites, the K and two F atoms in the 6c (m) sites, and one F atom in the 2a (3m) site. The structure consists of face-sharing K(6) octahedra with a fluoride anion at the center of each octahedron, forming chains of composition [FK(3)](2+) running along [001] with isolated [TaF(7)](2-) trigonal prisms in between. The structure of the title compound is different from the reported structure of Na(3)TaF(8) and represents a new structure type.

  16. Synthesis and characterization of Cu{sub 3}TaIn{sub 3}Se{sub 7} and CuTa{sub 2}InTe{sub 4}

    Energy Technology Data Exchange (ETDEWEB)

    Calderon, E.; Munoz-Pinto, M.; Duran-Pina, S.; Quintero, M.; Quintero, E.; Morocoima, M. [Centro de Estudios de Semiconductores, Departamento de Fisica, Facultad de Ciencias, Universidad de Los Andes, Merida (Venezuela); Delgado, G.E. [Laboratorio de Cristalografia, Departamento de Quimica, Facultad de Ciencias, Universidad de Los Andes, Merida (Venezuela); Romero, H. [Laboratorio de Magnetismo, Departamento de Fisica, Facultad de Ciencias, Universidad de Los Andes, Merida (Venezuela); Briceno, J.M.; Fernandez, J. [Laboratorio de Analisis Quimico y Estructural (LAQUEM), Departamento de Fisica, Facultad de Ciencias, Merida (Venezuela); Grima-Gallardo, P.

    2008-07-15

    Polycrystalline samples of Cu{sub 3}TaIn{sub 3}Se{sub 7} and CuTa{sub 2}InTe{sub 4} were synthesized by the usual melt and anneal technique. X-ray powder diffraction showed a single phase behavior for both samples with tetragonal symmetry and unit cell parameter values a=5.794{+-}0.002 A, c=11.66{+-}0.01 A, c/a=2.01, V=391{+-}1 A{sup 3} and a=6.193{+-}0.001 A, c=12.400 {+-}0.002A, c/a=2.00, V=475{+-}1 A{sup 3}, respectively. Differential thermal analysis (DTA) measurements suggested a complicated behavior near the melting point with several thermal transitions observed in the heating and cooling runs. From the shape of the DTA peaks it was deduced that the melting is incongruent for both materials. Magnetic susceptibility measurements (zero-field cooling and field cooling) indicated an antiferromagnetic character with transition temperatures of T=70 K (Cu{sub 3}TaIn{sub 3}Se{sub 7}) and 42 K (CuTa{sub 2}InTe{sub 4}). A spin-glass transition was observed in Cu{sub 3}TaIn{sub 3}Se{sub 7} with T{sub f}{approx}50 K. (copyright 2008 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim) (orig.)

  17. Effect of Ta substitution method on the mechanical properties of Ni3(Si,Ti) intermetallic alloy

    International Nuclear Information System (INIS)

    Imajo, Daiki; Kaneno, Yasuyuki; Takasugi, Takayuki

    2013-01-01

    In this study, Ta was added to an L1 2 -type Ni 3 (Si,Ti) alloy at different levels and into different substitution sites, substituting for either Ni, Ti or Si. The solubility limits of Ta in the L1 2 phase were 1.9 at%, 5.7 at% and 1.0 at% when Ta substituted for Ni, Ti and Si, respectively. The lattice parameters in the L1 2 phase region increased in the order of the Ta(Ni)>Ta(Si)>Ta(Ti) quaternary alloys, in which Ta substituted for Ni, Si and Ti, respectively. The room-temperature hardness in the L1 2 phase region increased linearly with increasing Ta content, and the increment rate increased in the order of the Ta(Ni)>Ta(Si)>Ta(Ti) quaternary alloys. Similarly, the room-temperature 0.2% proof stress as well as the tensile strength in the L1 2 phase region increased linearly with increasing Ta content, and the increment rate increased in the order of the Ta(Ni)>Ta(Si)>Ta(Ti) quaternary alloys. High tensile elongation was observed at room temperature when the microstructures remain in the L1 2 single phase. At high temperatures, a positive temperature dependence of the hardness as well as the flow strength was observed in the quaternary alloys. It was also shown that the wear resistance of the quaternary Ta(Ti) alloys was improved and attributed to plastically induced hardening of the worn surfaces combined with the positive temperature dependence of the flow strength. The strengthening and hardening resulting from Ta addition was suggested to be due to the hardening of the solid solution arising from the misfits in the atomic radius between Ta and the constituent atoms Ni, Ti or Si

  18. Experimental and ab initio study of Ta-doped ZnO semiconductor

    Energy Technology Data Exchange (ETDEWEB)

    Munoz, E. L., E-mail: munoz@fisica.unlp.edu.ar; Richard, D., E-mail: richard@fisica.unlp.edu.ar [UNLP, Departamento de Fisica and Instituto de Fisica La Plata (IFLP, CCT La Plata, CONICET), Fac. de Ciencias Exactas (Argentina); Eversheim, P. D. [Universitaet Bonn, Helmholtz-Institut fuer Strahlen-und Kernphysik (H-ISKP) (Germany); Renteria, M., E-mail: renteria@fisica.unlp.edu.ar [UNLP, Departamento de Fisica and Instituto de Fisica La Plata (IFLP, CCT La Plata, CONICET), Fac. de Ciencias Exactas (Argentina)

    2010-04-15

    In this work, we present {gamma}-{gamma} Perturbed-Angular-Correlation results in polycrystalline ZnO semiconductor implanted with {sup 181}Hf({yields}{sup 181}Ta) probes. Calculations in Ta-doped ZnO were carried out using the Full-Potential Augmented Plane Wave plus local orbital method in a supercell and varying self-consistently the charge state of the impurity. Ta is a triple donor impurity with respect to Zn{sup 2 + } in ZnO and thus it can loose 1, 2 or 3 donor electrons under certain circumstances. As expected, the comparison between the experimental Electric-Field-Gradient tensor results and our ab initio predictions shows that the Ta impurity is in an ionized charge state at room temperature.

  19. Experimental and ab initio study of Ta-doped ZnO semiconductor

    International Nuclear Information System (INIS)

    Muñoz, E. L.; Richard, D.; Eversheim, P. D.; Rentería, M.

    2010-01-01

    In this work, we present γ–γ Perturbed-Angular-Correlation results in polycrystalline ZnO semiconductor implanted with 181 Hf(→ 181 Ta) probes. Calculations in Ta-doped ZnO were carried out using the Full-Potential Augmented Plane Wave plus local orbital method in a supercell and varying self-consistently the charge state of the impurity. Ta is a triple donor impurity with respect to Zn 2 +  in ZnO and thus it can loose 1, 2 or 3 donor electrons under certain circumstances. As expected, the comparison between the experimental Electric-Field-Gradient tensor results and our ab initio predictions shows that the Ta impurity is in an ionized charge state at room temperature.

  20. Photo-Induced depopulation of the 180mTa isomer

    Science.gov (United States)

    Bhike, Megha; Krishichayan, Fnu; Tornow, W.

    2015-10-01

    The 180mTa nucleus is the rarest isotope in the universe, existing only in an isomeric state at 77.2 keV (Jπ = 9-) with half-life of greater than 7.1 ×1015 years. The stellar production of this high-spin isomer has been a challenging astrophysical problem. Cross-section measurements for the depopulation of the 180mTa isomer with monoenergetic photon beams of energies 2.5 and 3.1 MeV have been carried out at the HI γS facility. The activated Ta foils of natural abundance and containing 14.4 mg of 180mTa were γ-ray counted at TUNL's low background facility using a 13% planar HPGe detector. A 8'' ×12'' NaI detector in combination with the standard HI γS scintillator paddle system was employed for absolute photon-flux determination. Preliminary results will be discussed, and measurements at lower energies are planned. This work was supported by the U.S. DOE under Grant NO. DE-FG02-97ER41033.

  1. Superconducting properties of (Nb,Ta)3Sn wires fabricated by the bronze process

    International Nuclear Information System (INIS)

    Suenaga, M.; Aihara, K.; Kaiho, K.; Luhman, T.S.

    1979-01-01

    Measurements of the superconducting critical temperature T/sub c/, critical current density, J/sub c/ (8 3 Sn monofilamentary wires. Ta content in the Nb 3 Sn compound was varied by alloying the Nb core prior to a reaction heat treatment. Core compositions were 0, 3, 7, 10, and 20 wt% Ta and heat treatments for the reaction were 16, 64, and 120 h at 725 0 C. For the 120 h heat treatment T/sub c/ decreased monotonically with Ta content from 17.5 to 15.7K while H/sub c2/ increased from 19.8 to 24.6 T. With increasing Ta content J/sub c/ (16 T) increased from 0.7 x 10 5 A/cm 2 to a maximum value of 1.3 x 10 5 at 7 wt% Ta. Further increases in the Ta content produced a decrease in J/sub c/(16 T). At 10 T J/sub c/ decreased with increasing Ta content. An important aspect of this work is the observation that alloying with Ta did not hinder wire ductility during drawing. It appears therefore that the improvements in J/sub c/(16 T) can be incorporated into commercially manufactured conductors

  2. Suboxide/subnitride formation on Ta masks during magnetic material etching by reactive plasmas

    Energy Technology Data Exchange (ETDEWEB)

    Li, Hu; Muraki, Yu; Karahashi, Kazuhiro; Hamaguchi, Satoshi, E-mail: hamaguch@ppl.eng.osaka-u.ac.jp [Center for Atomic and Molecular Technologies, Osaka University, Yamadaoka 2-1, Suita 565-0871 (Japan)

    2015-07-15

    Etching characteristics of tantalum (Ta) masks used in magnetoresistive random-access memory etching processes by carbon monoxide and ammonium (CO/NH{sub 3}) or methanol (CH{sub 3}OH) plasmas have been examined by mass-selected ion beam experiments with in-situ surface analyses. It has been suggested in earlier studies that etching of magnetic materials, i.e., Fe, Ni, Co, and their alloys, by such plasmas is mostly due to physical sputtering and etch selectivity of the process arises from etch resistance (i.e., low-sputtering yield) of the hard mask materials such as Ta. In this study, it is shown that, during Ta etching by energetic CO{sup +} or N{sup +} ions, suboxides or subnitrides are formed on the Ta surface, which reduces the apparent sputtering yield of Ta. It is also shown that the sputtering yield of Ta by energetic CO{sup +} or N{sup +} ions has a strong dependence on the angle of ion incidence, which suggests a correlation between the sputtering yield and the oxidation states of Ta in the suboxide or subnitride; the higher the oxidation state of Ta, the lower is the sputtering yield. These data account for the observed etch selectivity by CO/NH{sub 3} and CH{sub 3}OH plasmas.

  3. Effects of helium and deuterium irradiation on SPS sintered W–Ta composites at different temperatures

    Energy Technology Data Exchange (ETDEWEB)

    Mateus, R., E-mail: rmateus@ipfn.ist.utl.pt [Associação Euratom/IST, Instituto de Plasmas e Fusão Nuclear, Instituto Superior Técnico, Universidade Técnica de Lisboa, Av. Rovisco Pais, 1049-001 Lisboa (Portugal); Dias, M. [ITN, Instituto Tecnológico e Nuclear, Estrada Nacional 10, 2686-953 Sacavém (Portugal); Lopes, J. [ITN, Instituto Tecnológico e Nuclear, Estrada Nacional 10, 2686-953 Sacavém (Portugal); ISEL, Instituto Superior de Engenharia de Lisboa, Rua Conselheiro Emídio Navarro, 1, 1959-007 Lisboa (Portugal); Rocha, J.; Catarino, N.; Franco, N. [ITN, Instituto Tecnológico e Nuclear, Estrada Nacional 10, 2686-953 Sacavém (Portugal); Livramento, V. [Associação Euratom/IST, Instituto de Plasmas e Fusão Nuclear, Instituto Superior Técnico, Universidade Técnica de Lisboa, Av. Rovisco Pais, 1049-001 Lisboa (Portugal); LNEG, Laboratório Nacional de Energia e Geologia, Estrada do Paço do Lumiar, 1649-038 Lisboa (Portugal); and others

    2013-11-15

    Energetic He{sup +} and D{sup +} ions were implanted into different W–Ta composites in order to investigate their stability under helium and deuterium irradiation. The results were compared with morphological and chemical modifications arising from exposure of pure W and Ta. Special attention was given to tantalum hydride (Ta{sub 2}H) formation due to its implications for tritium inventory. Three W–Ta composites with 10 and 20 at.% Ta were prepared from elemental W powder and Ta fibre or powder through low-energy ball milling in argon atmosphere. Spark plasma sintering (SPS) was used as the consolidation process in the temperature range from 1473 to 1873 K. The results obtained from pure elemental samples and composites are similar. However, Ta{sub 2}H is easily formed in pure Ta by using a pre-implantation stage of He{sup +}, whereas in W–Ta composites the same reaction is clearly reduced, and it can be inhibited by controlling the sintering temperature.

  4. Mutagenic and antimutagenic activities of Artemisia absinthium volatile oil by the bacterial reverse mutation assay in Salmonella typhimurium strains TA98 and TA100

    Directory of Open Access Journals (Sweden)

    Mahboubeh Taherkhani

    2014-09-01

    Full Text Available Objective: To investigate the mutagenic and antimutagenic activities of Artemisia absinthium L. (A. absinthium essential oil by the bacterial reverse mutation assay in Salmonella typhimurium (S. typhimurium strains. Methods: Water-distilled essential oil of A. absinthium collected from Ardabil, NorthWestern Iran, was investigated for mutagenic and antimutagenic activities. In present study, the mutagenic and antimutagenic activities of A. absinthium oil were investigated by the bacterial revere mutation assay in S. typhimurium TA98 and TA100 strains with and without S9 (microsomal mutagenesis assay. Results: The comparative mutagenicity effect was seen in 1.5 mg/plate by the bacterial reverse mutation assay in S. typhimurium TA98 strains, without S9 and the excellent antimutagenicity effect was seen in 1.5 mg/plate against S. typhimurium TA100, without S9. Conclusions: The mutagenicity and antimutagenicity effects of the volatile oil of A. absinthium were seen without the presence of metabolic activation.

  5. Love-type surface acoustic wave on Y-X LiTaO3 with amorphous Ta2O5 thin film

    Science.gov (United States)

    Kakio, Shoji; Fukasawa, Haruka; Hosaka, Keiko

    2015-07-01

    In this study, to obtain a substrate structure with a lower phase velocity, the propagation properties of a Love-type surface acoustic wave (Love SAW) on Y-X LiTaO3 (LT) with an amorphous tantalum pentoxide (a-Ta2O5) thin film were investigated using a simple delay line and a resonator with a wavelength λ of 8 µm. The insertion loss of a simple delay line was decreased markedly by loading with an a-Ta2O5 film owing to a transformation from a leaky SAW (LSAW) to a non-leaky Love SAW. A phase velocity of 3,340 m/s, a coupling factor of 5.8%, and a propagation loss of 0.03 dB/λ were obtained for a normalized thickness h/λ of 0.120. Moreover, the resonance properties of the Love SAW were almost equal or superior to those for an LSAW on Al/36° Y-X LT, except for the fractional bandwidth.

  6. Rotational structures in 174Ta

    International Nuclear Information System (INIS)

    Hojman, Daniel; Kreiner, A.J.; Davidson, Miguel

    1989-01-01

    The nucleus 174 Ta has been studied for the first time through the fusion-evaporation reaction 169 Tm ( 9 Be,4n) using a 4 mg/cm 2 self-supporting Tm foil in the 40 to 65 MeV bombarding energy range (the 4n channel was found to peak at 50 MeV). The experiments comprised γ and X-ray singles in beam and activity spectra, γ-γ-t coincidences (one of the counters was Compton suppressed) and γ-ray angular distributions. The results obtained allowed the construction of a high-spin level scheme. This scheme, which resembles that of 172 Ta, comprises several rotational bands which correspond to different couplings of the valence nucleons. One of these structures, the doubly decoupled band (DDB), is particularly interesting because it is the first observed case of a DDB based on an I π =3 + state. (Author) [es

  7. Effects of crystal structure and composition on the photocatalytic performance of Ta-O-N functional materials.

    Science.gov (United States)

    Liu, Qing-Lu; Zhao, Zong-Yan; Yi, Jian-Hong

    2018-05-07

    For photocatalytic applications, the response of a material to the solar spectrum and its redox capabilities are two important factors determined by the band gap and band edge position of the electronic structure of the material. The crystal structure and composition of the photocatalyst are fundamental for determining the above factors. In this article, we examine the functional material Ta-O-N as an example of how to discuss relationships among these factors in detail with the use of theoretical calculations. To explore how the crystal structure and composition influence the photocatalytic performance, two groups of Ta-O-N materials were considered: the first group included ε-Ta 2 O 5 , TaON, and Ta 3 N 5 ; the second group included β-Ta 2 O 5 , δ-Ta 2 O 5 , ε-Ta 2 O 5 , and amorphous-Ta 2 O 5 . Calculation results indicated that the band gap and band edge position are determined by interactions between the atomic core and valence electrons, the overlap of valence electronic states, and the localization of valence states. Ta 3 N 5 and TaON are suitable candidates for efficient photocatalysts owing to their photocatalytic water-splitting ability and good utilization efficiency of solar energy. δ-Ta 2 O 5 has a strong oxidation potential and a band gap suitable for absorbing visible light. Thus, it can be applied to photocatalytic degradation of most pollutants. Although a-Ta 2 O 5 , ε-Ta 2 O 5 , and β-Ta 2 O 5 cannot be directly used as photocatalysts, they can still be applied to modify conventional Ta-O-N photocatalysts, owing to their similar composition and structure. These calculation results will be helpful as reference data for analyzing the photocatalytic performance of more complicated Ta-O-N functional materials. On the basis of these findings, one could design novel Ta-O-N functional materials for specific photocatalytic applications by tuning the composition and crystal structure.

  8. New levels of Ta II with energies higher than 72,000 cm−1

    International Nuclear Information System (INIS)

    Uddin, Zaheer; Windholz, Laurentius

    2014-01-01

    We studied the hyperfine structure of Tantalum lines appearing in a high-resolution Fourier transform spectrum. Hundreds of lines of Ta in this spectrum are still unclassified; most of them, especially in the UV region, belong to Ta II. When investigating such lines we found 14 new levels of Ta II. These new levels are the highest-lying known Ta II levels and do not belong to the already known configurations. - Highlights: • We report the discovery of 14 even energy levels of the first ion of Tantalum (Ta II). • Their energy ranges from 72,000 to 81,000 cm −1 . • For comparison, up to now only even levels between 0 and 44,000 cm −1 were known. • These levels belong to up to now unknown electron configurations. • With help of these levels, approximately 100 spectral lines of Ta II can be classified

  9. Method of treating Ti--Nb--Zr--Ta superconducting alloys

    International Nuclear Information System (INIS)

    Horiuchi, T.; Monju, Y.; Tatara, I.; Nagai, N.; Hisata, M.; Matsumoto, K.

    1975-01-01

    A superconducting alloy is formulated from 10 to 50 at. percent Ti, 20 to 50 at. percent Nb, 10 to 40 at. percent Zr, and 5 to 12 at. percent Ta. A Ti--Nb--Zr--Ta superconducting alloy with a fine, non-homogeneous structure is obtained by forming a β solid solution of Ti--Nb--Zr--Ta alloy by heating to a temperature within the β solid solution range, cooling, and then cold working the heated alloy. The cold worked alloy is heated to a temperature within the (β' + β'') alloy to maintain the peritectoid structure, cold worked, then heated to a temperature within the eutectoid range to form a multiphase alloy structure and then cooled and finally cold worked. (U.S.)

  10. Nanocrystalline β-Ta Coating Enhances the Longevity and Bioactivity of Medical Titanium Alloys

    Directory of Open Access Journals (Sweden)

    Linlin Liu

    2016-09-01

    Full Text Available A β-Ta nanocrystalline coating was engineered onto a Ti-6Al-4V substrate using a double cathode glow discharge technique to improve the corrosion resistance and bioactivity of this biomedical alloy. The new coating has a thickness of ~40 μm and exhibits a compact and homogeneous structure composed of equiaxed β-Ta grains with an average grain size of ~22 nm, which is well adhered on the substrate. Nanoindentation and scratch tests indicated that the β-Ta coating exhibited high hardness combined with good resistance to contact damage. The electrochemical behavior of the new coating was systematically investigated in Hank’s physiological solution at 37 °C. The results showed that the β-Ta coating exhibited a superior corrosion resistance as compared to uncoated Ti-6Al-4V and commercially pure tantalum, which was attributed to a stable passive film formed on the β-Ta coating. The in vitro bioactivity was studied by evaluating the apatite-forming capability of the coating after seven days of immersion in Hank’s physiological solution. The β-Ta coating showed a higher apatite-forming ability than both uncoated Ti-6Al-4V and commercially pure Ta, suggesting that the β-Ta coating has the potential to enhance functionality and increase longevity of orthopaedic implants.

  11. Characterisation of Ta-based barrier films on SiLK for Cu-metalisation

    NARCIS (Netherlands)

    van Nieuwkasteele-Bystrova, Svetlana Nikolajevna; Holleman, J.; Woerlee, P.H.; Wolters, Robertus A.M.

    2002-01-01

    Structures with Ta, TaxN1-x, Ta90C10, Ta95Si5 on SiLK were tested using in-situ 4- point probe resistance measurements during annealing up to 400oC. The change in normalized resistance by a factor of up to 2.58 was attributed to oxygen diffusion out of SiLK layer into the barriers. No direct

  12. TaGW2, a Good Reflection of Wheat Polyploidization and Evolution.

    Science.gov (United States)

    Qin, Lin; Zhao, Junjie; Li, Tian; Hou, Jian; Zhang, Xueyong; Hao, Chenyang

    2017-01-01

    Hexaploid wheat consists of three subgenomes, namely, A, B, and D. These well-characterized ancestral genomes also exist at the diploid and tetraploid levels, thereby rendering wheat as a good model species for studying polyploidization. Here, we performed intra- and inter-species comparative analyses of wheat and its relatives to dissect polymorphism and differentiation of the TaGW2 genes. Our results showed that genetic diversity of TaGW2 decreased with progression from the diploids to tetraploids and hexaploids. The strongest selection occurred in the promoter regions of TaGW2-6A and TaGW2-6B . Phylogenetic trees clearly indicated that Triticum urartu and Ae. speltoides were the donors of the A and B genomes in tetraploid and hexaploid wheats. Haplotypes detected among hexaploid genotypes traced back to the tetraploid level. Fst and π values revealed that the strongest selection on TaGW2 occurred at the tetraploid level rather than in hexaploid wheat. This infers that grain size enlargement, especially increased kernel width, mainly occurred in tetraploid genotypes. In addition, relative expression levels of TaGW2s significantly declined from the diploid level to tetraploids and hexaploids, further indicating that these genes negatively regulate kernel size. Our results also revealed that the polyploidization events possibly caused much stronger differentiation than domestication and breeding.

  13. Core level photoemission spectroscopy and chemical bonding in Sr2Ta2O7

    DEFF Research Database (Denmark)

    Atuchin, V. V.; Grivel, Jean-Claude; Zhang, Z. M.

    2009-01-01

    Electronic parameters of constituent element core levels of strontium pyrotantalate (Sr2Ta2O7) were measured with X-ray photoelectron spectroscopy (XPS). The Sr2Ta2O7 powder sample was synthesized using standard solid state method. The valence electron transfer on the formation of the Sr-O and Ta......-O bonds was characterized by the binding energy differences between the O 1s and cation core levels, Delta(O-Sr) = BE(O 1s) - BE(Sr 3d(5/2)) and Delta(O-Ta) = BE(O 1s) - BE(Ta 4f(7/2)). The chemical bonding effects were considered on the basis of our XPS results for Sr2Ta2O7 and earlier published...

  14. Superconductivity and specific heat measurements in V--Nb--Ta ternary alloys

    International Nuclear Information System (INIS)

    Wang, R.Y.P.

    1977-01-01

    The correlation between the superconducting transition temperature T/sub c/ with electronic specific heat coefficient γ and Debye temperature theta/sub D/ in some isoelectronic ternary V--Nb--Ta alloys is investigated. It has been known that the variation of theta/sub D/ with concentration in both V--Nb and V--Ta systems is clearly of the same curvature as that of T/sub c/ and γ. In Ta--Nb alloys, however, over most of the concentration range theta/sub D/ seems to have a slight negative curvature while T/sub c/ and γ curve upwards. (But beyond approx. 80 at. % Nb theta/sub D/ rises rapidly to the pure Nb value.) By choosing alloys along a line connecting Ta and V 25 --Nb 75 which is close to the Nb--Ta side of the Gibb's triangle the extent to which the Nb--Ta type of behavior persists in this ternary system can be estimated. A model proposed by Miedema that takes into account the variation of properties caused by possible charge transfer among constituent atoms in an alloy has been found to apply almost quantitatively for nearly all binary alloy systems whose experimental data are available, including those for which Hopfield's method fails. A previous test of the extension of Miedema's empirical model into ternary alloys shows qualitatively correct behavior for intra-row Zr/sub x/Nb/sub 1-2x/Mo/sub x/ alloys. The good agreement between the predicted values of γ and T/sub c/ and the experimental values in the inter-row ternary V--Nb--Ta system studied here gives another and better test of the application of Miedema's model

  15. Effect of Ta substitution method on the mechanical properties of Ni{sub 3}(Si,Ti) intermetallic alloy

    Energy Technology Data Exchange (ETDEWEB)

    Imajo, Daiki; Kaneno, Yasuyuki; Takasugi, Takayuki, E-mail: takasugi@mtr.osakafu-u.ac.jp

    2013-12-20

    In this study, Ta was added to an L1{sub 2}-type Ni{sub 3}(Si,Ti) alloy at different levels and into different substitution sites, substituting for either Ni, Ti or Si. The solubility limits of Ta in the L1{sub 2} phase were 1.9 at%, 5.7 at% and 1.0 at% when Ta substituted for Ni, Ti and Si, respectively. The lattice parameters in the L1{sub 2} phase region increased in the order of the Ta(Ni)>Ta(Si)>Ta(Ti) quaternary alloys, in which Ta substituted for Ni, Si and Ti, respectively. The room-temperature hardness in the L1{sub 2} phase region increased linearly with increasing Ta content, and the increment rate increased in the order of the Ta(Ni)>Ta(Si)>Ta(Ti) quaternary alloys. Similarly, the room-temperature 0.2% proof stress as well as the tensile strength in the L1{sub 2} phase region increased linearly with increasing Ta content, and the increment rate increased in the order of the Ta(Ni)>Ta(Si)>Ta(Ti) quaternary alloys. High tensile elongation was observed at room temperature when the microstructures remain in the L1{sub 2} single phase. At high temperatures, a positive temperature dependence of the hardness as well as the flow strength was observed in the quaternary alloys. It was also shown that the wear resistance of the quaternary Ta(Ti) alloys was improved and attributed to plastically induced hardening of the worn surfaces combined with the positive temperature dependence of the flow strength. The strengthening and hardening resulting from Ta addition was suggested to be due to the hardening of the solid solution arising from the misfits in the atomic radius between Ta and the constituent atoms Ni, Ti or Si.

  16. Formation of titanium dioxide nanotubes on Ti–30Nb–xTa alloys by anodizing

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Eun-Sil [Department of Dental Materials and Research Center of Nano-Interface Activation for Biomaterials, School of Dentistry, Chosun University, Gwangju (Korea, Republic of); Jeong, Yong-Hoon [Department of Dental Materials and Research Center of Nano-Interface Activation for Biomaterials, School of Dentistry, Chosun University, Gwangju (Korea, Republic of); Biomechanics and Tissue Engineering Laboratory, Division of Orthodontics, College of Dentistry, The Ohio State University, Columbus, OH (United States); Choe, Han-Cheol, E-mail: hcchoe@chosun.ac.kr [Department of Dental Materials and Research Center of Nano-Interface Activation for Biomaterials, School of Dentistry, Chosun University, Gwangju (Korea, Republic of); Brantley, William A. [Division of Restorative, Prosthetic and Primary Care Dentistry, College of Dentistry, The Ohio State University, Columbus, OH (United States)

    2013-12-31

    The goal of this study was to investigate the formation of titanium dioxide nanotubes on the surface of cast Ti–30Nb–xTa alloys by anodizing. The anodization technique for creating the nanotubes utilized a potentiostat and an electrolyte containing 1 M H{sub 3}PO{sub 4} with 0.8 wt.% NaF. The grain size of the Ti–30Nb–xTa alloys increased as the Ta content increased. Using X-ray diffraction, for the Ti–30Nb alloy the main peaks were identified as α″ martensite with strong peaks of β phase. The phases in the Ti–30Nb–xTa alloys changed from a duplex (α″ + β) microstructure to solely β phase with increasing Ta content. The nanotubes that formed on the surface of the Ti–30Nb–xTa alloys were amorphous TiO{sub 2} without an evidence of the crystalline anatase or rutile forms of TiO{sub 2}. Scanning electron microscopy revealed that the average diameters of the small and large nanotubes on the Ti–30Nb alloy not containing Ta were approximately 100 nm and 400 nm, respectively, whereas the small and large nanotubes on the alloy had diameters of approximately 85 nm and 300 nm, respectively. As the Ta content increased from 0 to 15 wt.%, the average lengths of the nanotubes increased from 2 μm to 3.5 μm. Energy-dispersive X-ray spectroscopy indicated that the nanotubes were principally composed of Ti, Nb, Ta, O and F. Contact angle measurements showed that the nanotube surface had good wettability by water droplets. - Highlights: • TiO{sub 2} nanotube layers on anodized Ti-30Nb-xTa alloys have been investigated. • Nanotube surface had an amorphous structure without heat treatment. • Nanotube diameter of Ti-30Nb-xTa decreased, whereas tube layer increased with Ta content. • The nanotube surface exhibited the low contact angle and good wettability.

  17. Formation of titanium dioxide nanotubes on Ti–30Nb–xTa alloys by anodizing

    International Nuclear Information System (INIS)

    Kim, Eun-Sil; Jeong, Yong-Hoon; Choe, Han-Cheol; Brantley, William A.

    2013-01-01

    The goal of this study was to investigate the formation of titanium dioxide nanotubes on the surface of cast Ti–30Nb–xTa alloys by anodizing. The anodization technique for creating the nanotubes utilized a potentiostat and an electrolyte containing 1 M H 3 PO 4 with 0.8 wt.% NaF. The grain size of the Ti–30Nb–xTa alloys increased as the Ta content increased. Using X-ray diffraction, for the Ti–30Nb alloy the main peaks were identified as α″ martensite with strong peaks of β phase. The phases in the Ti–30Nb–xTa alloys changed from a duplex (α″ + β) microstructure to solely β phase with increasing Ta content. The nanotubes that formed on the surface of the Ti–30Nb–xTa alloys were amorphous TiO 2 without an evidence of the crystalline anatase or rutile forms of TiO 2 . Scanning electron microscopy revealed that the average diameters of the small and large nanotubes on the Ti–30Nb alloy not containing Ta were approximately 100 nm and 400 nm, respectively, whereas the small and large nanotubes on the alloy had diameters of approximately 85 nm and 300 nm, respectively. As the Ta content increased from 0 to 15 wt.%, the average lengths of the nanotubes increased from 2 μm to 3.5 μm. Energy-dispersive X-ray spectroscopy indicated that the nanotubes were principally composed of Ti, Nb, Ta, O and F. Contact angle measurements showed that the nanotube surface had good wettability by water droplets. - Highlights: • TiO 2 nanotube layers on anodized Ti-30Nb-xTa alloys have been investigated. • Nanotube surface had an amorphous structure without heat treatment. • Nanotube diameter of Ti-30Nb-xTa decreased, whereas tube layer increased with Ta content. • The nanotube surface exhibited the low contact angle and good wettability

  18. Seismic assessment of Technical Area V (TA-V).

    Energy Technology Data Exchange (ETDEWEB)

    Medrano, Carlos S.

    2014-03-01

    The Technical Area V (TA-V) Seismic Assessment Report was commissioned as part of Sandia National Laboratories (SNL) Self Assessment Requirement per DOE O 414.1, Quality Assurance, for seismic impact on existing facilities at Technical Area-V (TA-V). SNL TA-V facilities are located on an existing Uniform Building Code (UBC) Seismic Zone IIB Site within the physical boundary of the Kirtland Air Force Base (KAFB). The document delineates a summary of the existing facilities with their safety-significant structure, system and components, identifies DOE Guidance, conceptual framework, past assessments and the present Geological and Seismic conditions. Building upon the past information and the evolution of the new seismic design criteria, the document discusses the potential impact of the new standards and provides recommendations based upon the current International Building Code (IBC) per DOE O 420.1B, Facility Safety and DOE G 420.1-2, Guide for the Mitigation of Natural Phenomena Hazards for DOE Nuclear Facilities and Non-Nuclear Facilities.

  19. High current density and nonlinearity combination of selection device based on TaO(x)/TiO2/TaO(x) structure for one selector-one resistor arrays.

    Science.gov (United States)

    Lee, Wootae; Park, Jubong; Kim, Seonghyun; Woo, Jiyong; Shin, Jungho; Choi, Godeuni; Park, Sangsu; Lee, Daeseok; Cha, Euijun; Lee, Byoung Hun; Hwang, Hyunsang

    2012-09-25

    We demonstrate a high-performance selection device by utilizing the concept of crested oxide barrier to suppress the sneak current in bipolar resistive memory arrays. Using a TaO(x)/TiO(2)/TaO(x) structure, high current density over 10(7) A cm(-2) and excellent nonlinear characteristics up to 10(4) were successfully demonstrated. On the basis of the defect chemistry and SIMS depth profile result, we found that some Ta atoms gradually diffused into TiO(2) film, and consequently, the energy band of the TiO(2) film was symmetrically bent at the top and bottom TaO(x)/TiO(2) interfaces and modified as a crested oxide barrier. Furthermore, the one selector-one resistor device exhibited significant suppression of the leakage current, indicating excellent selector characteristics.

  20. Magnetism of Ta dichalcogenide monolayers tuned by strain and hydrogenation

    Energy Technology Data Exchange (ETDEWEB)

    Manchanda, Priyanka; Sellmyer, D. J.; Skomski, Ralph [Department of Physics and Astronomy and Nebraska Center for Materials and Nanoscience, University of Nebraska, Lincoln, Nebraska 68588 (United States); Sharma, Vinit [Department of Materials Science and Engineering and Institute of Materials Science, University of Connecticut, Storrs, Connecticut 06269 (United States); Yu, Hongbin [School of Electrical, Computer, and Energy Engineering, Arizona State University, Tempe, Arizona 85287 (United States)

    2015-07-20

    The effects of strain and hydrogenation on the electronic, magnetic, and optical properties of monolayers of Ta based dichalcogenides (TaX{sub 2}; X = S, Se, and Te) are investigated using density-functional theory. We predict a complex scenario of strain-dependent magnetic phase transitions involving paramagnetic, ferromagnetic, and modulated antiferromagnetic states. Covering one of the two chalcogenide surfaces with hydrogen switches the antiferromagnetic/nonmagnetic TaX{sub 2} monolayers to a semiconductor, and the optical behavior strongly depends on strain and hydrogenation. Our research opens pathways towards the manipulation of magnetic as well as optical properties for future spintronics and optoelectronics applications.

  1. Morphological instability of Ag films caused by phase transition in the underlying Ta barrier layer

    Energy Technology Data Exchange (ETDEWEB)

    Mardani, Shabnam, E-mail: shabnam.mardani@angstrom.uu.se; Vallin, Örjan; Wätjen, Jörn Timo; Norström, Hans; Olsson, Jörgen; Zhang, Shi-Li, E-mail: shili.zhang@angstrom.uu.se [Solid State Electronics, The Ångström Laboratory, Uppsala University, P.O. Box 534, SE-75121 (Sweden)

    2014-08-18

    Wide-bandgap (WBG) semiconductor technologies are maturing and may provide increased device performance in many fields of applications, such as high-temperature electronics. However, there are still issues regarding the stability and reliability of WBG devices. Of particular importance is the high-temperature stability of interconnects for electronic systems based on WBG-semiconductors. For metallization without proper encapsulation, morphological degradation can occur at elevated temperatures. Sandwiching Ag films between Ta and/or TaN layers in this study is found to be electrically and morphologically stabilize the Ag metallization up to 800 °C, compared to 600 °C for uncapped films. However, the barrier layer plays a key role and TaN is found to be superior to Ta, resulting in the best achieved stability, whereas the difference between Ta and TaN caps is negligible. The β-to-α phase transition in the underlying Ta barrier layer is identified as the major cause responsible for the morphological instability observed above 600 °C. It is shown that this phase transition can be avoided using a stacked Ta/TaN barrier.

  2. Atomistic simulation of the point defects in B2-type MoTa alloy

    International Nuclear Information System (INIS)

    Zhang Jianmin; Wang Fang; Xu Kewei; Ji, Vincent

    2009-01-01

    The formation and migration mechanisms of three different point defects (mono-vacancy, anti-site defect and interstitial atom) in B 2 -type MoTa alloy have been investigated by combining molecular dynamics (MD) simulation with modified analytic embedded-atom method (MAEAM). From minimization of the formation energy, we find that the anti-site defects Mo Ta and Ta Mo are easier to form than Mo and Ta mono-vacancies, while Mo and Ta interstitial atoms are difficult to form in the alloy. In six migration mechanisms of Mo and Ta mono-vacancies, one nearest-neighbor jump (1NNJ) is the most favorable due to its lowest activation and migration energies, but it will cause a disorder in the alloy. One next-nearest-neighbor jump (1NNNJ) and one third-nearest-neighbor jump (1TNNJ) can maintain the ordered property of the alloy but require higher activation and migration energies, so the 1NNNJ and 1TNNJ should be replaced by straight [1 0 0] six nearest-neighbor cyclic jumps (S[1 0 0]6NNCJ) or bent [1 0 0] six nearest-neighbor cyclic jumps (B[1 0 0]6NNCJ) and [1 1 0] six nearest-neighbor cyclic jumps ([1 1 0]6NNCJ), respectively. Although the migrations of Mo and Ta interstitial atoms need much lower energy than Mo and Ta mono-vacancies, they are not main migration mechanisms due to difficult to form in the alloy.

  3. Extraordinary high strength Ti-Zr-Ta alloys through nanoscaled, dual-cubic spinodal reinforcement.

    Science.gov (United States)

    Biesiekierski, Arne; Ping, Dehai; Li, Yuncang; Lin, Jixing; Munir, Khurram S; Yamabe-Mitarai, Yoko; Wen, Cuie

    2017-04-15

    While titanium alloys represent the current state-of-the-art for orthopedic biomaterials, concerns still remain over their modulus. Circumventing this via increased porosity requires high elastic admissible strains, yet also limits traditional thermomechanical strengthening techniques. To this end, a novel β-type Ti-Zr-Ta alloy system, comprised of Ti-45Zr-10Ta, Ti-40Zr-14Ta, Ti-35Zr-18Ta and Ti-30Zr-22Ta, was designed and characterized mechanically and microstructurally. As-cast, this system displayed extremely high yield strengths and elastic admissible strains, up to 1.4GPa and potentially 1.48%, respectively. This strength was attributed to a nanoscaled, cuboidal structure of semi-coherent, dual body-centered cubic (BCC) phases, arising from the thermodynamics of interaction between Ta and Zr; this morphology occurring with dual BCC-phases is heretofore unreported in Ti-based alloys. Further, cell proliferation investigated by MTS assay suggests this was achieved without sacrificing biocompatibility, with no significant difference to either empty-well or commercially-pure Ti controls noted. The current research details microstructural, mechanical, and biological investigations into four novel biomedical alloys in a hitherto uninvestigated region of the Ti-Zr-Ta alloy system; Ti-45Zr-10Ta, Ti-40Zr-14Ta, Ti-35Zr-18Ta and Ti-30Zr-22Ta. We find that the investigated alloys display 0.2% yield strengths of up to 1.40GPa and elastic admissible strains of up to 1.48%, along with biological properties comparable to that seen in the conventional metallic biomaterial ASTM Grade-2 CP-Ti, achieved in the complete absence of traditional thermomechanical processing techniques. This is attributed to the presence of a dual-BCC cuboidal nanostructure, achieved via spinodal decomposition; while similar structures have been reported in e.g. Ni-based superalloys, we believe this is the first such structure investigated in a Ti-based material. As such, this work is felt to be of

  4. Evaluation of the potential for surface faulting at TA-63. Final report

    International Nuclear Information System (INIS)

    Kolbe, T.; Sawyer, J.; Springer, J.; Olig, S.; Hemphill-Haley, M.; Wong, I.; Reneau, S.

    1995-01-01

    This report describes an investigation of the potential for surface faulting at the proposed sites for the Radioactive Liquid Waste Treatment Facility (RL)WF) and the Hazardous Waste Treatment Facility at TA-63 and TA-52 (hereafter TA-63), Los Alamos National Laboratory (LANL). This study was performed by Woodward-Clyde Federal Services (WCFS) at the request of the LANL. The projections of both the Guaje Mountain and Rendija Canyon faults are mapped in the vicinity of TA-63. Based on results obtained in the ongoing Seismic Hazard Evaluation Program of the LANL, displacement may have occurred on both the Guaje Mountain and Rendija Canyon faults in the past 11,000 years (Holocene time). Thus, in accordance with US Department of Energy (DOE) Orders and Standards for seismic hazards evaluations and the US Environmental Protection Agency (EPA) Resource Conservation and Recovery Act (RCRA) Regulations for seismic standard requirements, a geologic study of the proposed TA-63 site was conducted

  5. Studies on layer growth and interfaces on Ta-base thin layers by means of XPS

    International Nuclear Information System (INIS)

    Zier, M.

    2007-01-01

    In this thesis studies on the growth and on the formation of the interfaces of Ta and TaN layers on Si and SiO 2 were performed. In the system TaN on SiO 2 no reaction on the interface could be found. As the system with the mostly disturbed interface Ta on SiO 2 was proved. Here a reduction of the SiO 2 at simultaneous oxidation of the Ta was to be observed. Additionally tantalum silicide was formed to be considered concerning the bonding state as Ta 5 Si 3 , from which a double layer of a tantalum silicide and a tantalum suboxide resulted. A whole thickness of the double layer of above 1 nm resulted. In the system Ta on Si at the deposition of the film on the interface a tantalum silicide was formed to be characterized concerning the bonding state as TaSi 2 . The thickness of the interlayer growed thereby up to 0.8 nm in form of islands. Finally in the system TaN on Si a silicon nitride formation during the deposition was observed, which was attributed to the insertion of adsorbed nitrogen from the sputtering atmosphere by recoil implantation of the sputtered Ta atoms. The silicon nitride interlayer growed thereby up to a thickness of 0.8 nm

  6. Synthesis, crystal structure and properties of K2Ta2S10: A novel ternary tantalum polysulfide with TaS8 polyhedra forming infinite anionic chains

    International Nuclear Information System (INIS)

    Wu Yuandong; Naether, Christian; Bensch, Wolfgang

    2005-01-01

    The new ternary alkali tantalum polysulfide K 2 Ta 2 S 10 has been synthesized by reacting TaS 2 with an in situ formed melt of K 2 S 3 and S at 773K. The compound crystallizes with four formula units in the monoclinic space group P2 1 /n (No. 14) with lattice parameters of a=14.9989(13)A,b=6.4183(4)A,c=15.1365(13)A,β=117.629(9) o . The structure contains two different zigzag chain anions [TaS 5 ] - , running parallel to the crystallographic b-axis separated by potassium cations. The two crystallographically independent tantalum atoms are in a distorted bi-capped trigonal prismatic environment of eight sulfur atoms which was never observed before. The TaS 8 polyhedra share three S atoms on each side to form the anionic chains. The compound was characterized with FIR and Raman spectroscopy

  7. Combined TiN- and TaN temperature compensated thin film resistors

    International Nuclear Information System (INIS)

    Malmros, Anna; Andersson, Kristoffer; Rorsman, Niklas

    2012-01-01

    The opposite signs of the temperature coefficient of resistance (TCR) of two thin film materials, titanium nitride (TiN) and tantalum nitride (TaN), were used to form temperature compensated thin film resistors (TFRs). The principle of designing temperature compensated TFRs by connecting TFRs of each compound in series or in parallel was demonstrated. TiN, TaN, and combined TiN and TaN TFRs for monolithic microwave integrated circuits (MMICs) were fabricated by reactive sputtering. DC characterization was performed over the temperature range of 30–200 °C. The TiN TFRs exhibited an increase in resistivity with temperature with TCRs of 540 and 750 ppm/°C. The TaN TFR on the other hand exhibited a negative TCR of − 470 ppm/°C. The shunted TFRs were fabricated by serial deposition of TiN and TaN to form a bilayer component. The TCRs of the series- and shunt configurations were experimentally reduced to − 60 and 100 ppm/°C, respectively. The concept of temperature compensation was used to build a Wheatstone bridge with an application in on-chip temperature sensing.

  8. SEMICONDUCTOR TECHNOLOGY: TaN wet etch for application in dual-metal-gate integration technology

    Science.gov (United States)

    Yongliang, Li; Qiuxia, Xu

    2009-12-01

    Wet-etch etchants and the TaN film method for dual-metal-gate integration are investigated. Both HF/HN O3/H2O and NH4OH/H2O2 solutions can etch TaN effectively, but poor selectivity to the gate dielectric for the HF/HNO3/H2O solution due to HF being included in HF/HNO3/H2O, and the fact that TaN is difficult to etch in the NH4OH/H2O2 solution at the first stage due to the thin TaOxNy layer on the TaN surface, mean that they are difficult to individually apply to dual-metal-gate integration. A two-step wet etching strategy using the HF/HNO3/H2O solution first and the NH4OH/H2O2 solution later can fully remove thin TaN film with a photo-resist mask and has high selectivity to the HfSiON dielectric film underneath. High-k dielectric film surfaces are smooth after wet etching of the TaN metal gate and MOSCAPs show well-behaved C-V and Jg-Vg characteristics, which all prove that the wet etching of TaN has little impact on electrical performance and can be applied to dual-metal-gate integration technology for removing the first TaN metal gate in the PMOS region.

  9. Consolidation of W–Ta composites: Hot isostatic pressing and spark and pulse plasma sintering

    Energy Technology Data Exchange (ETDEWEB)

    Dias, M., E-mail: marta.dias@itn.pt [Instituto de Plasmas e Fusão Nuclear, Instituto Superior Técnico, Universidade de Lisboa, Av. Rovisco Pais, 1049-001 Lisboa (Portugal); Guerreiro, F. [Instituto de Plasmas e Fusão Nuclear, Instituto Superior Técnico, Universidade de Lisboa, Av. Rovisco Pais, 1049-001 Lisboa (Portugal); Correia, J.B. [LNEG, Laboratório Nacional de Energia e Geologia, Estrada do Paço do Lumiar, 1649-038 Lisboa (Portugal); Galatanu, A. [National Institute of Materials Physics, Atomistilor 105 bis Bucharest-Magurele, 077125 Ilfov (Romania); Rosiński, M. [Warsaw University of Technology, Faculty of Materials Science and Engineering, Warsaw (Poland); Monge, M.A.; Munoz, A. [Departamento de Física, Univerdidad Carlos III de Madrid, Avd. de la Universidad 30, 28911 Madrid (Spain); Alves, E. [Instituto de Plasmas e Fusão Nuclear, Instituto Superior Técnico, Universidade de Lisboa, Av. Rovisco Pais, 1049-001 Lisboa (Portugal); Carvalho, P.A. [Instituto de Plasmas e Fusão Nuclear, Instituto Superior Técnico, Universidade de Lisboa, Av. Rovisco Pais, 1049-001 Lisboa (Portugal); CeFEMA, Instituto Superior Técnico, Universidade de Lisboa, Av. Rovisco Pais, 1049-001 Lisboa (Portugal)

    2015-10-15

    Highlights: • Consolidation of W–Ta composites using three techniques: HIP, SPS and PPS. • Comparison of consolidation methods in terms of W–Ta interdiffusion and densification. • Microstructure analysis in terms of oxides formation. - Abstract: Composites consisting of tantalum fiber/powder dispersed in a nanostructured W matrix have been consolidated by spark and pulse plasma sintering as well as by hot isostatic pressing. The microstructural observations revealed that the tungsten–tantalum fiber composites consolidated by hot isostatic pressing and pulse plasma sintering presented a continuous layer of Ta{sub 2}O{sub 5} phase at the W/Ta interfaces, while the samples consolidated by spark plasma sintering evidenced a Ta + Ta{sub 2}O{sub 5} eutectic mixture due to the higher temperature of this consolidation process. Similar results have been obtained for the tungsten–tantalum powder composites. A (W, Ta) solid solution was detected around the prior nanostructured W particles in tungsten–tantalum powder composites consolidated by spark and pulse plasma sintering. Higher densifications were obtained for composites consolidated by hot isostatic pressing and pulse plasma sintering.

  10. XYO{sub 3} (X = K, Na; Y = Nb, Ta) based superlattices for photocatalysis

    Energy Technology Data Exchange (ETDEWEB)

    Wang, Guang-Zhao; Chen, Xiao-Rui; Yuan, Hong-Kuan; Kuang, An-Long [School of Physical Science and Technology, Southwest University, Chongqing 400715 (China); Chen, Hong [School of Physical Science and Technology, Southwest University, Chongqing 400715 (China); Key Laboratory of Luminescent and Real-Time Analytical Chemistry, Ministry of Education, College of Chemistry and Chemical Engineering, Southwest University, Chongqing 400715 (China)

    2017-05-15

    The photocatalytic activities of XYO{sub 3} (X = K, Na; Y = Ta, Nb) and XYO{sub 3}/X1Y1O{sub 3} (X, X1 = K, Na; Y, Y1 = Ta, Nb) systems are investigated by using hybrid density functional. All the XYO{sub 3} and XYO{sub 3}/X1Y1O{sub 3} systems are indirect band gap semiconductors, and the band gap of KNbO{sub 3}/KTaO{sub 3} is smaller than those of KNbO{sub 3} and KTaO{sub 3}, while the band gaps of KNbO{sub 3}/NaNbO{sub 3}, KNbO{sub 3}/NaTaO{sub 3}, KTaO{sub 3}/NaNbO{sub 3}, KTaO{sub 3}/NaTaO{sub 3}, and NaNbO{sub 3}/NaTaO{sub 3} are respectively between the band gaps of these two crystals which make up these superlattices. The electronic structure of KNbO{sub 3}/NaTaO{sub 3} is the same as that of KTaO{sub 3}/NaNbO{sub 3} since both have the same component and similar crystal structure. The band edges of all the considered superlattices are thermodynamically allowed for the water reduction and oxidation processes, and therefore, they could be used for photocatalytic water splitting. Band structures for (i) KNbO{sub 3}/KTaO{sub 3}, (ii) KNbO{sub 3}/NaNbO{sub 3}, (iii) KNbO{sub 3}/NaTaO{sub 3}, (iv) KTaO{sub 3}/NaNbO{sub 3}, (v) KTaO{sub 3}/NaTaO{sub 3}, and (vi) NaNbO{sub 3}/NaTaO{sub 3} superlattices. The horizontal dashed lines represent the Fermi levels. (copyright 2017 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

  11. Rancang Bangun Ulang Aplikasi MonTA Menggunakan Workflow Framework pada ASP.NET

    Directory of Open Access Journals (Sweden)

    Mohammad Oktri Radity

    2013-09-01

    Full Text Available Zaman sekarang kemajuan teknologi semakin berkembang pesat dari tahun ke tahun. Kebutuhan orang terhadap teknologi menjadi sangat penting. Aplikasi MonTA yang digunakan oleh jurusan Teknik Informatika ITS menjadi bukti kemajuan teknologi. Aplikasi yang dikembangkan oleh jurusan Teknik Informatika ini bertujuan untuk mengelola seluruh data tugas akhir mahasiswa Teknik Informatika. Aplikasi MonTA merupakan suatu sistem yang berkaitan dengan tugas akhir mahasiswa di jurusan Teknik Informatika, Institut Teknologi Sepuluh Nopember Surabaya. Tujuan dikembangkannya aplikasi ini adalah untuk mengelola data mahasiswa yang melaksanakan tugas akhir dan dosen dapat memonitoring mahasiswa yang sedang melakukan tugas akhir dengan aplikasi ini. Aplikasi ini juga memudahkan admin tugas akhir dalam melakukan tugasnya, antara lain: penjadwalan proposal, memonitor jumlah bimbingan mahasiswa tugas akhir, penjadwalan sidang tugas akhir, dan lain-lain. Namun, aplikasi MonTA yang sekarang digunakan masih memiliki banyak kekurangan. Oleh karena itu dibahas perancangan ulang aplikasi MonTA pada artikel ini. Metode baru yang digunakan pada rancang ulang aplikasi MonTA ini adalah dengan penerapan Workflow Framework pada ASP.NET. Diharapkan dengan rancang ulang aplikasi ini nantinya dapat memperbaiki berbagai kekurangan yang ada saat ini, seperti inkonsitensi data dan memperbaiki data yang terdapat pada  aplikasi MonTA menjadi lebih terstruktur

  12. Stable self-compliance resistive switching in AlOδ/Ta2O5−x/TaOy triple layer devices

    International Nuclear Information System (INIS)

    Wu, Huaqiang; Li, Xinyi; Huang, Feiyang; Yu, Zhiping; Qian, He; Chen, An

    2015-01-01

    Stable self-compliance property was observed in the AlO δ /Ta 2 O 5−x /TaO y triple-layer resistive random access memory structure. The impact of AlO δ barrier layer was studied with different thicknesses. Endurance of more than 10 10 cycles and data retention for more than 3 h at 125 °C were demonstrated. All the measurements were carried out without external current compliance and no hard breakdown was observed. Systematic analysis reveals the self-compliance property is due to the built-in series resistance of the thin AlO δ barrier layer. A model is proposed to explain this self-compliance property. (paper)

  13. 180Ta/sup g,m/ production cross sections form the 180Hf(p,n) reaction

    International Nuclear Information System (INIS)

    Norman, E.B.; Renner, T.R.; Grant, P.J.

    1981-01-01

    Cross sections have been determined for the production of the J/sup π/ = 1 + 180 Ta/sup g/ and the J/sup π/= 9 - 180 Ta/sup m/ from the 180 Hf(p,n) reaction. The 180 Ta/sup g/ cross sections were determined from measurements of γ-rays emitted following the electron-capture and β-decay of this 8.1-hour state. Total 180 Ta production cross sections were determined from measurements of the thick-target (p,n) yield. 180 Ta/sup m/ cross sections were calculated by subtracting the 180 Ta/sup g/ cross sections from the total (p,n) cross sections. These measurements are compared with the results of a statistical-model evaporation calculation

  14. Institutional Interpretation of Participatory TA

    DEFF Research Database (Denmark)

    Nielsen, Rasmus Øjvind

    2014-01-01

    . The aim of the article is thus to relate the challenges of establishing and continuing pTA as a societal practice to the question of societal institutions and their logics. Towards this aim, the paper draws on a number of different theoretical directions within New Institutionalism and attempts to build...

  15. Density functional study of TaSin (n = 1-3, 12) clusters adsorbed to graphene surface

    International Nuclear Information System (INIS)

    Guo Ping; Zheng Lin; Zheng Jiming; Zhang Ruizhi; Yang Luna; Ren, Zhaoyu

    2011-01-01

    A plane-wave density functional theory (DFT) calculations have been performed to investigate structural and electronic properties of TaSi n (n = 1-3, 12) clusters supported by graphene surface. The resulting adsorption structures are described and discussed in terms of stability, bonding, and electron transfer between the cluster and the graphene. The TaSi n clusters on graphene surface favor their free-standing ground-state structures. Especially in the cases of the linear TaSi 2 and the planar TaSi 3 , the graphene surface may catalyze the transition of the TaSi n clusters from an isomer of lower dimensionality into the ground-state structure. The adsorption site and configuration of TaSi n on graphene surface are dominated by the interaction between Ta atom and graphene. Ta atom prefers to adsorb on the hollow site of graphene, and Si atoms tend to locate on the bridge site. Further, the electron transfer is found to proceed from the cluster to the surface for n = 1 and 2, while its direction reverses as n > 2. For the case of TaSi, chemisorption is shown to prevail over physisorption as the dominant mode of surface-adsorbate interaction by charge density analysis.

  16. TaS2 nanosheet-based room-temperature dosage meter for nitric oxide

    Directory of Open Access Journals (Sweden)

    Qiyuan He

    2014-09-01

    Full Text Available A miniature dosage meter for toxic gas is developed based on TaS2 nanosheets, which is capable of indicating the toxic dosage of trace level NO at room temperature. The TaS2 film-based chemiresistor shows an irreversible current response against the exposure of NO. The unique non-recovery characteristic makes the TaS2 film-based device an ideal indicator of total dosage of chronicle exposure.

  17. Nd:Ta2O5 rib waveguide lasers

    International Nuclear Information System (INIS)

    Unal, Bayram; Tai, C.-Y.; Shepherd, David P.; Wilkinson, James S.; Perney, Nicolas M.B.; Netti, M. Caterina; Parker, Gregory J.

    2005-01-01

    Ta 2 O 5 waveguides offer great potential for high-density active photonic crystal circuits and their combination with rare-earth dopants for active devices is of interest for increasing their potential functionality. To this end, neodymium-doped Ta 2 O 5 rib waveguide lasers have been fabricated on an oxidized silicon wafer by rf sputtering and argon ion-beam milling and laser action in this material has been demonstrated. Lasing was observed at wavelenghts between 1060 and 1080 nm and an absorbed pump power threshold of 87 mW was obtained

  18. Molecular evolution of the rice blast resistance gene Pi-ta in invasive weedy rice in the USA.

    Directory of Open Access Journals (Sweden)

    Seonghee Lee

    Full Text Available The Pi-ta gene in rice has been effectively used to control rice blast disease caused by Magnaporthe oryzae worldwide. Despite a number of studies that reported the Pi-ta gene in domesticated rice and wild species, little is known about how the Pi-ta gene has evolved in US weedy rice, a major weed of rice. To investigate the genome organization of the Pi-ta gene in weedy rice and its relationship to gene flow between cultivated and weedy rice in the US, we analyzed nucleotide sequence variation at the Pi-ta gene and its surrounding 2 Mb region in 156 weedy, domesticated and wild rice relatives. We found that the region at and around the Pi-ta gene shows very low genetic diversity in US weedy rice. The patterns of molecular diversity in weeds are more similar to cultivated rice (indica and aus, which have never been cultivated in the US, rather than the wild rice species, Oryza rufipogon. In addition, the resistant Pi-ta allele (Pi-ta found in the majority of US weedy rice belongs to the weedy group strawhull awnless (SH, suggesting a single source of origin for Pi-ta. Weeds with Pi-ta were resistant to two M. oryzae races, IC17 and IB49, except for three accessions, suggesting that component(s required for the Pi-ta mediated resistance may be missing in these accessions. Signatures of flanking sequences of the Pi-ta gene and SSR markers on chromosome 12 suggest that the susceptible pi-ta allele (pi-ta, not Pi-ta, has been introgressed from cultivated to weedy rice by out-crossing.

  19. Molecular Evolution of the Rice Blast Resistance Gene Pi-ta in Invasive Weedy Rice in the USA

    Science.gov (United States)

    Lee, Seonghee; Jia, Yulin; Jia, Melissa; Gealy, David R.; Olsen, Kenneth M.; Caicedo, Ana L.

    2011-01-01

    The Pi-ta gene in rice has been effectively used to control rice blast disease caused by Magnaporthe oryzae worldwide. Despite a number of studies that reported the Pi-ta gene in domesticated rice and wild species, little is known about how the Pi-ta gene has evolved in US weedy rice, a major weed of rice. To investigate the genome organization of the Pi-ta gene in weedy rice and its relationship to gene flow between cultivated and weedy rice in the US, we analyzed nucleotide sequence variation at the Pi-ta gene and its surrounding 2 Mb region in 156 weedy, domesticated and wild rice relatives. We found that the region at and around the Pi-ta gene shows very low genetic diversity in US weedy rice. The patterns of molecular diversity in weeds are more similar to cultivated rice (indica and aus), which have never been cultivated in the US, rather than the wild rice species, Oryza rufipogon. In addition, the resistant Pi-ta allele (Pi-ta) found in the majority of US weedy rice belongs to the weedy group strawhull awnless (SH), suggesting a single source of origin for Pi-ta. Weeds with Pi-ta were resistant to two M. oryzae races, IC17 and IB49, except for three accessions, suggesting that component(s) required for the Pi-ta mediated resistance may be missing in these accessions. Signatures of flanking sequences of the Pi-ta gene and SSR markers on chromosome 12 suggest that the susceptible pi-ta allele (pi-ta), not Pi-ta, has been introgressed from cultivated to weedy rice by out-crossing. PMID:22043312

  20. Electron radiation defects in TaCsub(1-x) and TiCsub(0.97)

    International Nuclear Information System (INIS)

    Morillo, J.; Novion, C.H. de; Dural, J.

    1981-08-01

    The electrical resistivity changes of TaCsub(0.99) and TaCsub(0.80) have been measured at 21 K during irradiation with electrons of incident energies ranging from 2.5 to 0.25 MeV: a non-zero production rate is observed, even at the lowest energies. The recovery of defects was followed up to 400 K for TaCsub(0.99) and TiCsub(0.97) irradiated with 2.25 MeV electrons and up to 160 K for TaCsub(0.80) irradiated with 0.75 MeV electrons. The results are compared to fast neutron radiation damage data. For TiCsub(0.97) and TaCsub(0.99), the contributions of the different defects to the production rates and recovery spectra are tentatively separated, and a rough estimate of Frenkel pair resistivities is given

  1. Hot Ta filament resistance in-situ monitoring under silane containing atmosphere

    International Nuclear Information System (INIS)

    Grunsky, D.; Schroeder, B.

    2008-01-01

    Monitoring of the electrical resistance of the Ta catalyst during the hot wire chemical vapor deposition (HWCVD) of thin silicon films gives information about filament condition. Using Ta filaments for silane decomposition not only the well known strong changes at the cold ends, but also changes of the central part of the filament were observed. Three different phenomena can be distinguished: silicide (stoichiometric Ta X Si Y alloys) growth on the filament surfaces, diffusion of Si into the Ta filament and thick silicon deposits (TSD) formation on the filament surface. The formation of different tantalum silicides on the surface as well as the in-diffusion of silicon increase the filament resistance, while the TSDs form additional electrical current channels and that result in a decrease of the filament resistance. Thus, the filament resistance behaviour during ageing is the result of the competition between these two processes

  2. TaSiN nanocomposite thin films: Correlation between structure, chemical composition, and physical properties

    International Nuclear Information System (INIS)

    Ramírez, G.; Oezer, D.; Rivera, M.; Rodil, S.E.; Sanjinés, R.

    2014-01-01

    The structural and electronic properties of fcc-TaN/SiN x nanocomposite thin films deposited by reactive magnetron sputtering have been investigated as function of the N and Si contents. Our studies have been mainly focused on three different types of nanocomposite Ta x Si y N z films based on: nitrogen deficient fcc-TaN 0.88 , nearly stoichiometric fcc-TaN, and over-stoichiometric fcc-TaN 1.2 with the Si contents in the range from 0 to about 15 at.%. The optical properties were investigated by ellipsometric measurements, while the DC. electrical resistivity was measured using the van der Pauw configuration at 300 K. The optical measurements were interpreted using the standard Drude–Lorentz model. The results showed that the electronic properties are closely correlated with both the compositional and the structural modifications of the Ta x Si y N z films induced by the addition of Si atoms, and also depending on the stoichiometry of the starting fcc-TaN system. Thus, depending on both the nitrogen and the silicon contents, the fcc-Ta x Si y N z films can exhibit room temperature resistivity values ranging from 10 2 μΩ cm to about 6 × 10 4 μΩ cm. - Highlights: • TaSiN films were grown using dual magnetron sputtering system. • The physical and structural properties were correlated with the deposition parameters. • The electrical properties were influenced by the nitrogen and silicon contents on the films

  3. From Ba{sub 3}Ta{sub 5}O{sub 14}N to LaBa{sub 2}Ta{sub 5}O{sub 13}N{sub 2}: Decreasing the optical band gap of a photocatalyst

    Energy Technology Data Exchange (ETDEWEB)

    Anke, B. [Institut für Chemie, Technische Universität Berlin, Straße des 17. Juni 135, 10623 Berlin (Germany); Bredow, T. [Mulliken Center for Theoretical Chemistry, Institut für Physikalische und Theoretische Chemie, Universität Bonn, Beringstr. 4, 53115 Bonn (Germany); Pilarski, M.; Wark, M. [Institut für Chemie, Carl von Ossietzky Universität Oldenburg, Carl-von-Ossietzky-Str. 9-11, 26129 Oldenburg (Germany); Lerch, M., E-mail: martin.lerch@tu-berlin.de [Institut für Chemie, Technische Universität Berlin, Straße des 17. Juni 135, 10623 Berlin (Germany)

    2017-02-15

    Yellow LaBa{sub 2}Ta{sub 5}O{sub 13}N{sub 2} was successfully synthesized as phase-pure material crystallizing isostructurally to previously reported Ba{sub 3}Ta{sub 5}O{sub 14}N and mixed-valence Ba{sub 3}Ta{sup V}{sub 4}Ta{sup IV}O{sub 15}. The electronic structure of LaBa{sub 2}Ta{sub 5}O{sub 13}N{sub 2} was studied theoretically with the range-separated hybrid method HSE06. The most stable structure was obtained when lanthanum was placed on 2a and nitrogen on 4h sites confirming Pauling's second rule. By incorporating nitrogen, the measured band gap decreases from ∼3.8 eV for the oxide via 2.74 eV for Ba{sub 3}Ta{sub 5}O{sub 14}N to 2.63 eV for the new oxide nitride, giving rise to an absorption band well in the visible-light region. Calculated fundamental band gaps confirm the experimental trend. The atom-projected density of states has large contributions from N2p orbitals close to the valence band edge. These are responsible for the observed band gap reduction. Photocatalytic hydrogen formation was investigated and compared with that of Ba{sub 3}Ta{sub 5}O{sub 14}N revealing significantly higher activity for LaBa{sub 2}Ta{sub 5}O{sub 13}N{sub 2} under UV-light. - Graphical abstract: X-ray powder diffraction pattern of LaBa{sub 2}Ta{sub 5}O{sub 13}N{sub 2} with the results of the Rietveld refinements. Inset: Unit cell of LaBa{sub 2}Ta{sub 5}O{sub 13}N{sub 2} and polyhedral representation of the crystal structure. - Highlights: • Synthesis of a new oxide nitride LaBa{sub 2}Ta{sub 5}O{sub 13}N{sub 2}. • Refinement of the crystal structure. • Quantum chemical calculations provided band gap close to the measured value. • New phase shows a higher photocatalytic H{sub 2} evolution rate compared to prior tested Ba{sub 3}Ta{sub 5}O{sub 14}N.

  4. Wheat Transcription Factor TaAREB3 Participates in Drought and Freezing Tolerances in Arabidopsis.

    Science.gov (United States)

    Wang, Jingyi; Li, Qian; Mao, Xinguo; Li, Ang; Jing, Ruilian

    2016-01-01

    AREB (ABA response element binding) proteins in plants play direct regulatory roles in response to multiple stresses, but their functions in wheat (Triticum aestivum L.) are not clear. In the present study, TaAREB3, a new member of the AREB transcription factor family, was isolated from wheat. Sequence analysis showed that the TaAREB3 protein is composed of three parts, a conserved N-terminal, a variable M region, and a conserved C-terminal with a bZIP domain. It belongs to the group A subfamily of bZIP transcription factors. TaAREB3 was constitutively expressed in stems, leaves, florets, anthers, pistils, seeds, and most highly, in roots. TaAREB3 gene expression was induced with abscisic acid (ABA) and low temperature stress, and its protein was localized in the nucleus when transiently expressed in tobacco epidermal cells and stably expressed in transgenic Arabidopsis. TaAREB3 protein has transcriptional activation activity, and can bind to the ABRE cis-element in vitro. Overexpression of TaAREB3 in Arabidopsis not only enhanced ABA sensitivity, but also strengthened drought and freezing tolerances. TaAREB3 also activated RD29A, RD29B, COR15A, and COR47 by binding to their promoter regions in transgenic Arabidopsis. These results demonstrated that TaAREB3 plays an important role in drought and freezing tolerances in Arabidopsis.

  5. Solar control on irradiated Ta2O2 thin films

    International Nuclear Information System (INIS)

    Baydogan, N. D.; Zayim, E. Oe.

    2007-01-01

    Thin films consisting of Ta 2 O 5 have been used in industry in applications related to thin-film capacitors, optical waveguides, and antireflection coatings on solar cells. Ta 2 O 5 films are used for several special applications as highly refractive material and show different optical properties depending on the deposition methods. Sol-gel technique has been used for the preparation of Ta 2 O 5 thin films. Ta 2 O 5 thin films were prepared by sol-gel proses on glass substrates to obtain good quality films. These films were exposed to gamma radiation from Co-60 radioisotope. Ta 2 O 5 coated thin films were placed against the source and irradiated for 8 different gamma doses; between 0.35 and 21.00 kGy at room temperature. Energetic gamma ray can affect the samples and change its colour. On the other hand some of the Ta 2 O 5 coated thin films were irradiated with beta radiation from Sr-90 radioisotope. The effect of gamma irradiation on the solar properties of Ta 2 O 5 films is compared with that of beta irradiation. The solar properties of the irradiated thin films differ significantly from those of the unirradiated ones. After the irradiation of the samples transmittance and reflectance are measured for solar light between 300 and 2100 nm, by using Perkin Elmer Lambda 9 UV/VIS/NIR Spectrophotometer. Change in the direct solar transmittance, reflectance and absorptance with absorbed dose are determined. Using the optical properties, the redistribution of the absorbed component of the solar radiation and the shading coefficient (SC) are calculated as a function of the convective heat-transfer coefficient. Solar parameters are important for the determination of the shading coefficient. When the secondary internal heat transfer factor (qi), direct solar transmittance (□ e ), and solar factor (g) are known, it is possible to determine shading coefficient via the dose rates. The shading coefficient changes as the dose rate is increased. In this study, the shading

  6. Density Measurement of Liquid Ni-Ta Alloys by a Modified Sessile Drop Method

    Institute of Scientific and Technical Information of China (English)

    FANG Liang; XIAO Feng; TAO Zainan; Kusuhiro Mukai

    2005-01-01

    The density of liquid Ni-Ta alloys was measured by using a modified sessile drop method. It is found that the density of the liquid Ni-Ta alloys decreases with the increasing temperature, but increases with the increase of tantalum concentration in the alloys. The molar volume of liquid Ni-Ta binary alloys increases with the increase of temperature and tantalum concentration.

  7. Multipacting Simulations of Tuner-adjustable waveguide coupler (TaCo) with CST

    CERN Document Server

    Shafqat, Nuaman; Wegner, Rolf

    2015-01-01

    Tuner-adjustable waveguide couplers (TaCo) are used to feed microwave power to different RF structures of LINAC4. This paper studies the multipacting phenomenon for TaCo using PIC solver of CST PS. Simulations are performed for complete field sweeps and results are analysed.

  8. On the ex situ and in situ doping of refractory Ta by pulsed laser ablation

    Energy Technology Data Exchange (ETDEWEB)

    Lin, Y.L.; Lin, S.S.; Shen, P. [National Sun Yat-sen University, Department of Materials and Optoelectronic Science, Kaohsiung, Taiwan (China); Chen, S. [I-Shou University, Department of Mechanical and Automation Engineering, Kaohsiung, Taiwan (China)

    2017-06-15

    Ex situ and in situ doping processes of refractory Ta were accomplished by pulsed laser ablation of bulk Ta in vacuum with C-O-H supply from C-coated collodion film and within tetraethyl orthosilicate (TEOS), respectively. Analytical electron microscopic observations of the resultant particulates and condensates indicated that the former process involved interdiffusion in the condensed state to form two kinds of core-shell structures, i.e., C-O-H doped Ta with α-type (bcc) core and lamellar shell and O-H doped γ-TaC{sub 1-x} with amorphous Ta-C-O-H surrounding, respectively, for potential wear and lubrication applications at high temperatures. In situ TEOS mediation, however, enhanced solute trapping to form Si-C-O-H overdoped α-Ta with significant tetragonality (c/a ratio up to 1.27) and Si-O-H doped γ-TaC{sub 1-x} with {111}{sub γ} twin/fault and occasional epitaxial relationship [ anti 123]{sub α}//[ anti 112]{sub γ}; (121){sub α}//(anti 11 anti 1){sub γ} due to particle coalescence. Such Si-C-O-H mediated Ta particles may have potential optocatalytic applications. (orig.)

  9. Miks ta nii teeb? / Kristiina Voolaid

    Index Scriptorium Estoniae

    Voolaid, Kristiina

    1999-01-01

    Kuidas mõtleb ruumikujundaja, kui ta valib vorme, värve, materjale ja esemeid? Sisearhitekt Kristiina Voolaid seletab oma mõtteid Kawe Plaza hoones asuvate Hüvitusfondi ja Werol Tehased kontorite ning noorele perekonnale sisustatud vanalinnakorteri näitel

  10. Overexpression of a Triticum aestivum Calreticulin gene (TaCRT1 Improves Salinity Tolerance in Tobacco.

    Directory of Open Access Journals (Sweden)

    Yang Xiang

    Full Text Available Calreticulin (CRT is a highly conserved and abundant multifunctional protein that is encoded by a small gene family and is often associated with abiotic/biotic stress responses in plants. However, the roles played by this protein in salt stress responses in wheat (Triticum aestivum remain obscure. In this study, three TaCRT genes were identified in wheat and named TaCRT1, TaCRT2 and TaCRT3-1 based on their sequence characteristics and their high homology to other known CRT genes. Quantitative real-time PCR expression data revealed that these three genes exhibit different expression patterns in different tissues and are strongly induced under salt stress in wheat. The calcium-binding properties of the purified recombinant TaCRT1 protein were determined using a PIPES/Arsenazo III analysis. TaCRT1 gene overexpression in Nicotiana tabacum decreased salt stress damage in transgenic tobacco plants. Physiological measurements indicated that transgenic tobacco plants showed higher activities of superoxide dismutase (SOD, peroxidase (POD and catalase (CAT than non-transgenic tobacco under normal growth conditions. Interestingly, overexpression of the entire TaCRT1 gene or of partial TaCRT1 segments resulted in significantly higher tolerance to salt stress in transgenic plants compared with their WT counterparts, thus revealing the essential role of the C-domain of TaCRT1 in countering salt stress in plants.

  11. Electrodeposited ultrafine TaOx/CB catalysts for PEFC cathode application: Their oxygen reduction reaction kinetics

    KAUST Repository

    Seo, Jeongsuk

    2014-12-01

    Ultrafine TaOx nanoparticles were electrodeposited on carbon black (CB) powder in a nonaqueous Ta complex solution at room temperature, and the resultant TaOx/CB catalysts were assessed as oxygen reduction reaction (ORR) electrocatalysts for polymer electrolyte fuel cell (PEFC) cathodes. The Ta electrodeposition process was scaled up using a newly designed working electrode containing a CB dense layer, without introducing any binder such as the ionomer Nafion in the electrode for electrodeposition. The electrodeposited TaOx/CB powders were removed from the deposition electrode and subsequent H2 treatment at varying temperatures between 523 and 1073 K was attempted to increase the ORR performance. The TaOx/CB samples were characterized by SEM, STEM, XPS, and EELS measurements. XPS and EELS results indicated the reduced nature of the Ta species caused by the high-temperature treatment in H2, while STEM images clearly revealed that the TaOx particles aggregated as the treatment temperature increased. When the TaOx/CB catalyst, which was treated at 873 K for 2 h, was deposited on a glassy carbon substrate with Nafion ionomer, it resulted in the highest activity among the samples investigated, giving an onset potential of 0.95 VRHE at -2 μA cm-2 in a 0.1 M H2SO4 solution. Moreover, the long-term stability test with 10,000 cycles of the voltammetry only led to a 6% loss in the ORR currents, demonstrating the high stability of the TaOx/CB catalysts. Kinetic analysis by R(R)DE indicated that the four-electron transfer pathway in the ORR process was dominant for this TaOx/CB catalyst, and Tafel plots showed a slope corresponding to a one-electron reaction for the rate-determining step.

  12. Electrodeposited ultrafine TaOx/CB catalysts for PEFC cathode application: Their oxygen reduction reaction kinetics

    KAUST Repository

    Seo, Jeongsuk; Anjum, Dalaver H.; Takanabe, Kazuhiro; Kubota, Jun; Domen, Kazunari

    2014-01-01

    Ultrafine TaOx nanoparticles were electrodeposited on carbon black (CB) powder in a nonaqueous Ta complex solution at room temperature, and the resultant TaOx/CB catalysts were assessed as oxygen reduction reaction (ORR) electrocatalysts for polymer electrolyte fuel cell (PEFC) cathodes. The Ta electrodeposition process was scaled up using a newly designed working electrode containing a CB dense layer, without introducing any binder such as the ionomer Nafion in the electrode for electrodeposition. The electrodeposited TaOx/CB powders were removed from the deposition electrode and subsequent H2 treatment at varying temperatures between 523 and 1073 K was attempted to increase the ORR performance. The TaOx/CB samples were characterized by SEM, STEM, XPS, and EELS measurements. XPS and EELS results indicated the reduced nature of the Ta species caused by the high-temperature treatment in H2, while STEM images clearly revealed that the TaOx particles aggregated as the treatment temperature increased. When the TaOx/CB catalyst, which was treated at 873 K for 2 h, was deposited on a glassy carbon substrate with Nafion ionomer, it resulted in the highest activity among the samples investigated, giving an onset potential of 0.95 VRHE at -2 μA cm-2 in a 0.1 M H2SO4 solution. Moreover, the long-term stability test with 10,000 cycles of the voltammetry only led to a 6% loss in the ORR currents, demonstrating the high stability of the TaOx/CB catalysts. Kinetic analysis by R(R)DE indicated that the four-electron transfer pathway in the ORR process was dominant for this TaOx/CB catalyst, and Tafel plots showed a slope corresponding to a one-electron reaction for the rate-determining step.

  13. Atomic layer deposition and properties of mixed Ta2O5 and ZrO2 films

    Directory of Open Access Journals (Sweden)

    Kaupo Kukli

    2017-02-01

    Full Text Available Thin solid films consisting of ZrO2 and Ta2O5 were grown by atomic layer deposition at 300 °C. Ta2O5 films doped with ZrO2, TaZr2.75O8 ternary phase, or ZrO2 doped with Ta2O5 were grown to thickness and composition depending on the number and ratio of alternating ZrO2 and Ta2O5 deposition cycles. All the films grown exhibited resistive switching characteristics between TiN and Pt electrodes, expressed by repetitive current-voltage loops. The most reliable windows between high and low resistive states were observed in Ta2O5 films mixed with relatively low amounts of ZrO2, providing Zr to Ta cation ratio of 0.2.

  14. The Efficiency of Delone Coverings of the Canonical Tilings MATH {cal T}(*(A_4)) -> T^*(A4) and MATH {cal T}(*(D_6)) -> T^*(D6)

    Science.gov (United States)

    Papadopolos, Zorka; Kasner, Gerald

    This chapter is devoted to the coverings of the two quasiperiodic canonical tilings MATH {cal T}(*(A_4)) -> T^*(A4) and MATH {cal T}(*(D_6)) equiv {cal T}(*(2F)) -> T^*(D6) T^*(2F), obtained by projection from the root lattices A4 and D6, respectively. In the first major part of this chapter, in Sect. 5.2, we shall introduce a Delone covering MATH {cal C}(s_{{cal) T}(*(A_4)}) -> C^sT^*(A4) of the 2-dimensional decagonal tiling MATH {cal T}(*(A_4)) -> T^*(A4). In the second major part of this chapter, Sect. 5.3, we summarize the results related to the Delone covering of the icosahedral tiling MATH {cal T}(*(D_6)) -> T^*(D6), MATH {cal C}_{{cal T}(*(D_6)}) -> CT^*(D6) and determine the zero-, single-, and double- deckings and the resulting thickness of the covering. In the conclusions section, we give some suggestions as to how the definition of the Delone covering might be changed in order to reach some real (full) covering of the icosahedral tiling MATH {cal T}(*(D_6)) -> T^*(D6). In Section 5.2 the definition of the Delone covering is also changed in order to avoid an unnecessary large thickness of the covering.

  15. Crystallographic Structure Analysis of a Ti-Ta Thin Film Materials Library Fabricated by Combinatorial Magnetron Sputtering.

    Science.gov (United States)

    Kadletz, Peter M; Motemani, Yahya; Iannotta, Joy; Salomon, Steffen; Khare, Chinmay; Grossmann, Lukas; Maier, Hans Jürgen; Ludwig, Alfred; Schmahl, Wolfgang W

    2018-03-12

    Ti-Ta thin films exhibit properties that are of interest for applications as microactuators and as biomedical implants. A Ti-Ta thin film materials library was deposited at T = 25 °C by magnetron sputtering employing the combinatorial approach, which led to a compositional range of Ti 87 Ta 13 to Ti 14 Ta 86 . Subsequent high-throughput characterization methods permitted a quick and comprehensive study of the crystallographic, microstructural, and morphological properties, which strongly depend on the chemical composition. SEM investigation revealed a columnar morphology having pyramidal, sharp tips with coarser columns in the Ti-rich and finer columns in the Ta-rich region. By grazing incidence X-ray diffraction four phases were identified, from Ta-lean to Ta-rich: ω phase, α″ martensite, β phase, and a tetragonal Ta-rich phase (Ta (tetr) ). The crystal structure and microstructure were analyzed by Rietveld refinement and clear trends could be determined as a function of Ta-content. The lattice correspondences between β as the parent phase and α″ and ω as derivative phases were expressed in matrix form. The β ⇌ α″ phase transition shows a discontinuity at the composition where the martensitic transformation temperatures fall below room temperature (between 34 and 38 at. % Ta) rendering it first order and confirming its martensitic nature. A short study of the α″ martensite employing the Landau theory is included for a mathematical quantification of the spontaneous lattice strain at room temperature (ϵ̂ max = 22.4(6) % for pure Ti). Martensitic properties of Ti-Ta are beneficial for the development of high-temperature actuators with actuation response at transformation temperatures higher than 100 °C.

  16. A Study of Thin Film Resistors Prepared Using Ni-Cr-Si-Al-Ta High Entropy Alloy

    Directory of Open Access Journals (Sweden)

    Ruei-Cheng Lin

    2015-01-01

    Full Text Available Ni-Cr-Si-Al-Ta resistive thin films were prepared on glass and Al2O3 substrates by DC magnetron cosputtering from targets of Ni0.35-Cr0.25-Si0.2-Al0.2 casting alloy and Ta metal. Electrical properties and microstructures of Ni-Cr-Si-Al-Ta films under different sputtering powers and annealing temperatures were investigated. The phase evolution, microstructure, and composition of Ni-Cr-Si-Al-Ta films were characterized by X-ray diffraction (XRD, transmission electron microscopy (TEM, and Auger electron spectroscopy (AES. When the annealing temperature was set to 300°C, the Ni-Cr-Si-Al-Ta films with an amorphous structure were observed. When the annealing temperature was at 500°C, the Ni-Cr-Si-Al-Ta films crystallized into Al0.9Ni4.22, Cr2Ta, and Ta5Si3 phases. The Ni-Cr-Si-Al-Ta films deposited at 100 W and annealed at 300°C which exhibited the higher resistivity 2215 μΩ-cm with −10 ppm/°C of temperature coefficient of resistance (TCR.

  17. Microstructural evolution and creep of Fe-Al-Ta alloys

    Energy Technology Data Exchange (ETDEWEB)

    Prokopcakova, Petra; Svec, Martin [Technical University of Liberec (Czech Republic). Dept. of Material Science; Palm, Martin [Max-Planck-Institut fuer Eisenforschung GmbH, Duesseldorf (Germany). Structure and Nano-/Micromechanics of Materials

    2016-05-15

    The microstructural evolution in Fe-Al-Ta alloys containing 23 - 31 at.% Al and 1.5 - 2.2 at.% Ta has been studied in the temperature range 650 - 750 C by annealing for 1, 10, 100 and 1 000 h. The experiments confirm that in this temperature range the precipitation of the stable hexagonal C14 Laves phase is preceded by formation of coherent, metastable L2{sub 1} Heusler phase precipitates within the Fe-Al matrix. However, precipitates of C14 are observed after much shorter annealing times than previously assumed. Creep strength increases substantially with increasing Al content of the alloys because the solid solubility for Ta in the Fe-Al matrix increases with increasing Al content and solid-solution hardening contributes substantially to the observed high creep strength. It may therefore be that the microstructural changes during creep have no noticeable effect on creep strength.

  18. Microstructural evolution and creep of Fe-Al-Ta alloys

    International Nuclear Information System (INIS)

    Prokopcakova, Petra; Svec, Martin; Palm, Martin

    2016-01-01

    The microstructural evolution in Fe-Al-Ta alloys containing 23 - 31 at.% Al and 1.5 - 2.2 at.% Ta has been studied in the temperature range 650 - 750 C by annealing for 1, 10, 100 and 1 000 h. The experiments confirm that in this temperature range the precipitation of the stable hexagonal C14 Laves phase is preceded by formation of coherent, metastable L2 1 Heusler phase precipitates within the Fe-Al matrix. However, precipitates of C14 are observed after much shorter annealing times than previously assumed. Creep strength increases substantially with increasing Al content of the alloys because the solid solubility for Ta in the Fe-Al matrix increases with increasing Al content and solid-solution hardening contributes substantially to the observed high creep strength. It may therefore be that the microstructural changes during creep have no noticeable effect on creep strength.

  19. Electric-field gradients at Ta impurities in Sc{sub 2}O{sub 3} semiconductor

    Energy Technology Data Exchange (ETDEWEB)

    Richard, Diego, E-mail: richard@fisica.unlp.edu.ar [Departamento de Fisica e Instituto de Fisica La Plata (IFLP, CONICET La Plata), Facultad de Ciencias Exactas, Universidad Nacional de La Plata, CC 67, 1900 La Plata, Argentina. (Argentina); Munoz, Emiliano L. [Departamento de Fisica e Instituto de Fisica La Plata (IFLP, CONICET La Plata), Facultad de Ciencias Exactas, Universidad Nacional de La Plata, CC 67, 1900 La Plata, Argentina. (Argentina); Errico, Leonardo A. [Departamento de Fisica e Instituto de Fisica La Plata (IFLP, CONICET La Plata), Facultad de Ciencias Exactas, Universidad Nacional de La Plata, CC 67, 1900 La Plata, Argentina. (Argentina); Universidad Nacional del Noroeste Bonaerense (UNNOBA), Monteagudo 2772, 2700 Pergamino, Argentina. (Argentina); Renteria, Mario [Departamento de Fisica e Instituto de Fisica La Plata (IFLP, CONICET La Plata), Facultad de Ciencias Exactas, Universidad Nacional de La Plata, CC 67, 1900 La Plata, Argentina. (Argentina)

    2012-08-15

    In this work we present an ab initio study of Ta-doped Sc{sub 2}O{sub 3} semiconductor. Calculations were performed at dilute Ta impurities located at both cationic sites of the host structure, using the Augmented Plane Wave plus Local Orbitals (APW+lo) method. The structural atomic relaxations and the electric-field gradients (EFG) were studied for different charge states of the cell in order to simulate different ionization states of the double-donor Ta impurity. From the results for the EFG tensor at Ta impurity sites and the comparison with experimental results obtained using the Time-Differential {gamma}-{gamma} Perturbed-Angular-Correlations technique we could determined the structural distortions induced by the Ta impurity and the electronic structure of the doped-semiconductor.

  20. Haplotypes of the TaGS5-A1 gene are associated with thousand-kernel weight in Chinese bread wheat

    Directory of Open Access Journals (Sweden)

    Wang Sha Sha

    2016-06-01

    Full Text Available In previous work, we cloned TaGS5 gene and found the association of TaGS5-A1 alleles with agronomic traits. In this study, the promoter sequence of the TaGS5-A1 gene was isolated from bread wheat. Sequencing results revealed that a G insertion was found in position -1925 bp of the TaGS5-A1 gene (Reference to ATG, which occurred in the Sp1 domain of the promoter sequence. Combined with previous single nucleotide polymorphism (SNP in the TaGS5-A1 exon sequence, four genotypes were formed at the TaGS5-A1 locus and were designated as TaGS5-A1a-a, TaGS5-A1a-b, TaGS5-A1b-a, and TaGS5-A1b-b, respectively. Analysis of the association of TaGS5-A1 alleles with agronomic traits indicated that cultivars with the TaGS5-A1a-b allele possessed significantly higher thousand-kernel weight (TKW and lower plant height than cultivars with the TaGS5-A1a-a allele, and cultivars with the TaGS5-A1b-b allele showed higher TKW than cultivars with the TaGS5-A1b-a allele. The differences of these traits between the TaGS5-A1a-a and TaGS5-A1a-b alleles were larger than those of the TaGS5-A1b-a and TaGS5-A1b-b alleles, suggesting that the -1925G insertion plays the more important role in TaGS5-A1a genotypes than in TaGS5-A1b genotypes. qRT-PCR indicated that TaGS5-A1b-b possessed the significantly highest expression level among four TaGS5-A1 haplotypes in mature seeds and further showed a significantly higher expression level than TaGS5-A1b-a at five different developmental stages of the seeds, suggesting that high expression of TaGS5-A1 was positively associated with high TKW in bread wheat. This study could provide a relatively superior genotype in view of TKW in wheat breeding programs and could also provide important information for dissection of the regulatory mechanism of the yield-related traits.

  1. TaSYP71, a Qc-SNARE, Contributes to Wheat Resistance against Puccinia striiformis f. sp. tritici

    Directory of Open Access Journals (Sweden)

    Minjie eLiu

    2016-04-01

    Full Text Available N-ethylmaleimide-sensitive factor attachment protein receptors (SNAREs are involved in plant resistance; however, the role of SYP71 in the regulation of plant–pathogen interactions is not well known. In this study, we characterized a plant-specific SNARE in wheat, TaSYP71, which contains a Qc-SNARE domain. Three homologues are localized on chromosome 1AL, 1BL and 1DL. Using Agrobacterium-mediated transient expression, TaSYP71 was localized to the plasma membrane in Nicotiana benthamiana. Quantitative real-time PCR assays revealed that TaSYP71 homologues was induced by NaCl, H2O2 stress and infection by virulent and avirulent Puccinia striiformis f. sp. tritici (Pst isolates. Heterologous expression of TaSYP71 in Schizosaccharomyces pombe elevated tolerance to H2O2. Meanwhile, H2O2 scavenging gene (TaCAT was downregulated in TaSYP71 silenced plants treated by H2O2 compared to that in control, which indicated that TaSYP71 enhanced tolerance to H2O2 stress possibly by influencing the expression of TaCAT to remove the excessive H2O2 accumulation. When TaSYP71 homologues were all silenced in wheat by the virus-induced gene silencing system, wheat plants were more susceptible to Pst, with larger infection area and more haustoria number, but the necrotic area of wheat mesophyll cells were larger, one possible explanation that minor contribution of resistance to Pst was insufficient to hinder pathogen extension when TaSYP71were silenced, and the necrotic area was enlarged accompanied with the pathogen growth. Of course, later cell death could not be excluded. In addition, the expression of pathogenesis-related genes were down-regulated in TaSYP71 silenced wheat plants. These results together suggest that TaSYP71 play a positive role in wheat defence against Pst.

  2. Experiment and density functional theory analyses of GdTaO4 single crystal

    Science.gov (United States)

    Ding, Shoujun; Kinross, Ashlie; Wang, Xiaofei; Yang, Huajun; Zhang, Qingli; Liu, Wenpeng; Sun, Dunlu

    2018-05-01

    GdTaO4 is a type of excellent materials that can be used as scintillation, laser matrix as well as self-activated phosphor has generated significant interest. Whereas its band structure, electronic structure and optical properties are still need elucidation. To solve this intriguing problem, high-quality GdTaO4 single crystal (M-type) was grown successfully using Czochralski method. Its structure as well as optical properties was determined in experiment. Moreover, a systematic theoretical calculation based on the density function theory methods were performed on M-type and M‧-type GdTaO4 and their band structure, density of state as well as optical properties were obtained. Combine with the performed experiment results, the calculated results were proved with high reliability. Hence, the calculated results obtained in this work could provide a deep understanding of GdTaO4 material, which also useful for the further investigation on GdTaO4 material.

  3. A wheat cinnamyl alcohol dehydrogenase TaCAD12 contributes to host resistance to the sharp eyespot disease

    Directory of Open Access Journals (Sweden)

    Wei Rong

    2016-11-01

    Full Text Available Sharp eyespot, caused mainly by the necrotrophic fungus Rhizoctonia cerealis, is a destructive disease in hexaploid wheat (Triticum aestivum L.. In Arabidopsis, certain cinnamyl alcohol dehydrogenases (CADs have been implicated in monolignol biosynthesis and in defense response to bacterial pathogen infection. However, little is known about CADs in wheat defense responses to necrotrophic or soil-borne pathogens. In this study, we isolate a wheat CAD gene TaCAD12 in response to R. cerealis infection through microarray-based comparative transcriptomics, and study the enzyme activity and defense role of TaCAD12 in wheat. The transcriptional levels of TaCAD12 in sharp eyespot-resistant wheat lines were significantly higher compared with those in susceptible wheat lines. The sequence and phylogenetic analyses revealed that TaCAD12 belongs to IV group in CAD family. The biochemical assay proved that TaCAD12 protein is an authentic CAD enzyme and possesses catalytic efficiencies towards both coniferyl aldehyde and sinapyl aldehyde. Knock-down of TaCAD12 transcript significantly repressed resistance of the gene-silenced wheat plants to sharp eyespot caused by R. cerealis, whereas TaCAD12 overexpression markedly enhanced resistance of the transgenic wheat lines to sharp eyespot. Furthermore, certain defense genes (Defensin, PR10, PR17c, and Chitinase1 and monolignol biosynthesis-related genes (TaCAD1, TaCCR, and TaCOMT1 were up-regulated in the TaCAD12-overexpressing wheat plants but down-regulated in TaCAD12-silencing plants. These results suggest that TaCAD12 positively contributes to resistance against sharp eyespot through regulation of the expression of certain defense genes and monolignol biosynthesis-related genes in wheat.

  4. Ion-Exchange Reaction Of A-Site In A2Ta2O6 Pyrochlore Crystal Structure

    Directory of Open Access Journals (Sweden)

    Matsunami M.

    2015-06-01

    Full Text Available Na+ or K+ ion rechargeable battery is started to garner attention recently in Place of Li+ ion cell. It is important that A+ site ion can move in and out the positive-electrode materials. When K2Ta2O6 powder had a pyrochlore structure was only dipped into NaOH aqueous solution at room temperature, Na2Ta2O6 was obtained. K2Ta2O6 was fabricated from a tantalum sheet by a hydrothermal synthesize with KOH aqueous solution. When Na2Ta2O6 was dipped into KOH aqueous solution, K2Ta2O6 was obtained again. If KTaO3 had a perovskite structure was dipped, Ion-exchange was not observed by XRD. Because a lattice constant of pyrochlore structure of K-Ta-O system is bigger than perovskite, K+ or Na+ ion could shinny through and exchange between Ta5+ and O2− ion site in a pyrochlore structure. K+ or Na+ ion exchange of A2Ta2O6 pyrochlore had reversibility. Therefore, A2Ta2O6 had a pyrochlore structure can be expected such as Na+ ion rechargeable battery element.

  5. Israel: Benefits of the EduTA [Education and Training Appraisal

    International Nuclear Information System (INIS)

    2016-01-01

    The EduTA mission provided a unique opportunity to: • Bring together all the ministries and agencies regulating radiation protection to discuss the status of the regulatory framework for E&T; • Reactivate the National Advisory Committee to provide a coordination framework for the actions identified during the EduTA mission; • Strengthen national regulatory framework for E&T by identifying action to: develop and implement E&T requirements for medical practitioners; develop legislation to address optimization of radiation protection of patients during medical exposure; • Promote a sustainable approach to build competence by adopting a national strategy for E&T in radiation protection. The EduTA mission paved also the way for a more effective and needs-oriented request of assistance from IAEA through the Technical Cooperation programme

  6. Effects of a Ta interlayer on the phase transition of TiSi2 on Si(111)

    Science.gov (United States)

    Jeon, Hyeongtag; Jung, Bokhee; Kim, Young Do; Yang, Woochul; Nemanich, R. J.

    2000-09-01

    This study examines the effects of a thin Ta interlayer on the formation of TiSi2 on Si(111) substrate. The Ta interlayer was introduced by depositing Ta and Ti films sequentially on an atomically clean Si(111) substrate in an ultrahigh vacuum (UHV) system. Samples of 100 Å Ti with 5 and 10 Å Ta interlayers were compared to similar structures without an interlayer. After deposition, the substrates were annealed for 10 min, in situ, at temperatures between 500 and 750 °C in 50 °C increments. The TiSi2 formation with and without the Ta interlayer was analyzed with an X-ray diffractometer, Auger electron spectroscopy (AES), Scanning electron microscopy (SEM), transmission electron microscopy (TEM), and a four-point probe. The AES analysis data showed a 1:2 ratio of Ti:Si in the Ti-silicide layer and indicated that the Ta layer remained at the interface between TiSi2 and the Si(111) substrate. The C 49-C 54 TiSi2 phase transition temperature was lowered by ˜200 °C. The C 49-C 54 TiSi2 phase transition temperature was 550 °C for the samples with a Ta interlayer and was 750 °C for the samples with no Ta interlayer. The sheet resistance of the Ta interlayered Ti silicide showed lower values of resistivity at low temperatures which indicated the change in phase transition temperature. The C 54 TiSi2 displayed different crystal orientation when the Ta interlayer was employed. The SEM and TEM micrographs showed that the TiSi2 with a Ta interlayer significantly suppressed the tendency to islanding and surface agglomeration.

  7. Synthesis and characterization of Zn3Ta2O8 nanomaterials by hydrothermal method

    International Nuclear Information System (INIS)

    Bîrdeanu, M.; Bîrdeanu, A.-V.; Gruia, A.S.; Fagadar-Cosma, E.; Avram, C.N.

    2013-01-01

    Graphical abstract: The results of an experimental program that was focused on obtaining the Zn 3 Ta 2 O 8 nanocrystalline synthesized by hydrothermal method using tantalum (V) oxide and zinc nitrate, the results of the nanomaterial’s structure characterization and the optical spectral properties of such nanomaterials that were thoroughly investigated. Also, the experimental results are compared with ab initio calculations of electronic properties of Zn 3 Ta 2 O 8 . Highlights: •Zn 3 Ta 2 O 8 nanomaterials were synthesized by hydrothermal method and characterized. •The obtained nanomaterials has excellent phosphor, optical and morphological properties. •The material can be used in designing high performance optoelectronical devices. -- Abstract: Zn 3 Ta 2 O 8 has been synthesized by hydrothermal method using tantalum (V) oxide and zinc nitrate. The crystal structure and microstructure, phase composition and the absorption of Zn 3 Ta 2 O 8 nanomaterials were characterized by X-ray diffraction, FT/IR measurements, UV–VIS measurements, PL measurements, SEM and AFM techniques and BET analysis. XRD results show the single phase of Zn 3 Ta 2 O 8 and the average particle size that is 52 nm. This narrow nanometer size was also confirmed by AFM measurements. BET analysis revealed that the nanomaterials are mesoporous. The PL spectra show the blue luminescence of Ta 2 Zn 3 O 8 . Besides, in the present work we report ab initio calculations regarding electronic properties of Zn 3 Ta 2 O 8 ; the theoretical results are compared with the experimental ones

  8. Strengthening effect of nano-scaled precipitates in Ta alloying layer induced by high current pulsed electron beam

    Energy Technology Data Exchange (ETDEWEB)

    Tang, Guangze; Luo, Dian; Fan, Guohua [School of Material Science & Engineering, Harbin Institute of Technology, Harbin 150001 (China); Ma, Xinxin, E-mail: maxin@hit.edu.cn [State Key Laboratory of Advanced Welding and Joining, Harbin Institute of Technology, Harbin 150001 (China); Wang, Liqin [School of Mechatronics Engineering, Harbin Institute of Technology, Harbin 150001 (China)

    2017-05-01

    Highlights: • Ta alloying layer are fabricated by magnetron sputtering and high current pulsed electron beam. • Nano-scaled TaC precipitates forms within the δ-Fe grain after tempering treatment. • The mean diameter of TaC particles is about 5–8 nm. • The hardness of alloying layer increased by over 50% after formation of nano-scaled TaC particle. - Abstract: In this study, the combination of magnetron sputtering and high current pulsed electron beam are used for surface alloying treatment of Ta film on high speed steel. And the Ta alloying layer is about 6 μm. After tempering treatment, TaC phase forms in Ta alloying layer when the treated temperature is over 823 K. Through the TEM and HRTEM observation, a large amount of nano-scaled precipitates (mean diameter 5–8 nm) form within the δ-Fe grain in Ta alloying layer after tempering treatment and these nano-scaled precipitates are confirmed as TaC particles, which contribute to the strengthening effect of the surface alloying layer. The hardness of tempered alloying layer can reach to 18.1 GPa when the treated temperature is 823 K which increase by 50% comparing with the untreated steel sample before surface alloying treatment.

  9. Microstructural and mechanical characterization of biomedical Ti-Nb-Zr(-Ta) alloys

    International Nuclear Information System (INIS)

    Elias, L.M.; Schneider, S.G.; Schneider, S.; Silva, H.M.; Malvisi, F.

    2006-01-01

    In recent years there has been a significant development of novel implant alloys based on β-Ti such as Ti-Nb-Zr and Ti-Nb-Zr-Ta alloys systems. The purpose of this work is to provide characterization of Ti-35.3Nb-5.1Ta-7.1Zr and Ti-41.1Nb-7.1Zr alloys, in which Nb will substitute the atomic amount of Ta, with emphasis in the property-microstructure-composition relationships. These alloys are produced from commercially pure materials (Ti, Nb, Zr and Ta) by an arc melting method. All ingots were submitted to sequences of heat treatment (1000 deg. C/2 h - WQ), cold working by swaging procedures and other heat treatment (1000 deg. C/2 h - WQ). Specimens, in as cast and heat-treated condition, were examined by light and scanning electron microscopy (SEM). These results suggested the presence of β- and ω-phases. Mechanical properties were based on tensile and hardness tests. These alloys exhibit a lower modulus than that of conventional Ti alloys and the other mechanical properties are suitable for biomedical applications

  10. Composition analysis of Ta-W alloy using NAA and EDXRF techniques

    International Nuclear Information System (INIS)

    Swain, K.K.; Remya Devi, P.S.; Chavan, Trupti A.; Verma, R.; Reddy, A.V.R.

    2015-01-01

    Tantalum-Tungsten (Ta-W) alloy is a high strength alloy and is used in corrosion resistant chemical process equipment's including heat exchangers, condensers, heating and cooling coils and reaction vessels. Ta-W alloy is also used as ion extraction plate during laser Isotope separation of uranium and hence the composition is critical for its optimal application. The composition of the alloy was determined by neutron activation analysis (NAA) and energy dispersive X-ray fluorescence spectrometry (EDXRF) techniques. Ta-W alloy sample was received from Nuclear Fuel Complex (NFC), Hyderabad. For NAA, samples (50 - 500 mg) were sealed in polyethylene. High purity Ta foil (30 - 40 mg) and W foil (10 - 20 mg) were packed and used as comparators. Samples and standards were irradiated in the graphite reflector position of Advanced Heavy Water Reactor Critical Facility (AHWR CF) reactor, BARC, Mumbai for 4 hours. After suitable decay period, radioactivity assay was carried out using a 45% relative efficiency high purity germanium (HPGe) detector coupled to MCA with 8 k conversion gain

  11. Thickness-dependence of optical constants for Ta2O5 ultrathin films

    International Nuclear Information System (INIS)

    Zhang, Dong-Xu; Zheng, Yu-Xiang; Cai, Qing-Yuan; Lin, Wei; Wu, Kang-Ning; Mao, Peng-Hui; Zhang, Rong-Jun; Zhao, Hai-bin; Chen, Liang-Yao

    2012-01-01

    An effective method for determining the optical constants of Ta 2 O 5 thin films deposited on crystal silicon (c-Si) using spectroscopic ellipsometry (SE) measurement with a two-film model (ambient-oxide-interlayer-substrate) was presented. Ta 2 O 5 thin films with thickness range of 1-400 nm have been prepared by the electron beam evaporation (EBE) method. We find that the refractive indices of Ta 2 O 5 ultrathin films less than 40 nm drop with the decreasing thickness, while the other ones are close to those of bulk Ta 2 O 5 . This phenomenon was due to the existence of an interfacial oxide region and the surface roughness of the film, which was confirmed by the measurement of atomic force microscopy (AFM). Optical properties of ultrathin film varying with the thickness are useful for the design and manufacture of nano-scaled thin-film devices. (orig.)

  12. Thickness-dependence of optical constants for Ta2O5 ultrathin films

    Science.gov (United States)

    Zhang, Dong-Xu; Zheng, Yu-Xiang; Cai, Qing-Yuan; Lin, Wei; Wu, Kang-Ning; Mao, Peng-Hui; Zhang, Rong-Jun; Zhao, Hai-bin; Chen, Liang-Yao

    2012-09-01

    An effective method for determining the optical constants of Ta2O5 thin films deposited on crystal silicon (c-Si) using spectroscopic ellipsometry (SE) measurement with a two-film model (ambient-oxide-interlayer-substrate) was presented. Ta2O5 thin films with thickness range of 1-400 nm have been prepared by the electron beam evaporation (EBE) method. We find that the refractive indices of Ta2O5 ultrathin films less than 40 nm drop with the decreasing thickness, while the other ones are close to those of bulk Ta2O5. This phenomenon was due to the existence of an interfacial oxide region and the surface roughness of the film, which was confirmed by the measurement of atomic force microscopy (AFM). Optical properties of ultrathin film varying with the thickness are useful for the design and manufacture of nano-scaled thin-film devices.

  13. TaGS5-3A, a grain size gene selected during wheat improvement for larger kernel and yield.

    Science.gov (United States)

    Ma, Lin; Li, Tian; Hao, Chenyang; Wang, Yuquan; Chen, Xinhong; Zhang, Xueyong

    2016-05-01

    Grain size is a dominant component of grain weight in cereals. Earlier studies have shown that OsGS5 plays a major role in regulating both grain size and weight in rice via promotion of cell division. In this study, we isolated TaGS5 homoeologues in wheat and mapped them on chromosomes 3A, 3B and 3D. Temporal and spatial expression analysis showed that TaGS5 homoeologues were preferentially expressed in young spikes and developing grains. Two alleles of TaGS5-3A, TaGS5-3A-T and TaGS5-3A-G were identified in wheat accessions, and a functional marker was developed to discriminate them. Association analysis revealed that TaGS5-3A-T was significantly correlated with larger grain size and higher thousand kernel weight. Biochemical assays showed that TaGS5-3A-T possesses a higher enzymatic activity than TaGS5-3A-G. Transgenic rice lines overexpressing TaGS5-3A-T also exhibited larger grain size and higher thousand kernel weight than TaGS5-3A-G lines, and the transcript levels of cell cycle-related genes in TaGS5-3A-T lines were higher than those in TaGS5-3A-G lines. Furthermore, systematic evolution analysis in diploid, tetraploid and hexaploid wheat showed that TaGS5-3A underwent strong artificial selection during wheat polyploidization events and the frequency changes of two alleles demonstrated that TaGS5-3A-T was favoured in global modern wheat cultivars. These results suggest that TaGS5-3A is a positive regulator of grain size and its favoured allele TaGS5-3A-T exhibits a larger potential application in wheat high-yield breeding. © 2015 Society for Experimental Biology, Association of Applied Biologists and John Wiley & Sons Ltd.

  14. TaNAC29, a NAC transcription factor from wheat, enhances salt and drought tolerance in transgenic Arabidopsis.

    Science.gov (United States)

    Huang, Quanjun; Wang, Yan; Li, Bin; Chang, Junli; Chen, Mingjie; Li, Kexiu; Yang, Guangxiao; He, Guangyuan

    2015-11-04

    NAC (NAM, ATAF, and CUC) transcription factors play important roles in plant biological processes, including phytohormone homeostasis, plant development, and in responses to various environmental stresses. TaNAC29 was introduced into Arabidopsis using the Agrobacterium tumefaciens-mediated floral dipping method. TaNAC29-overexpression plants were subjected to salt and drought stresses for examining gene functions. To investigate tolerant mechanisms involved in the salt and drought responses, expression of related marker genes analyses were conducted, and related physiological indices were also measured. Expressions of genes were analyzed by quantitative real-time polymerase chain reaction (qRT-PCR). A novel NAC transcription factor gene, designated TaNAC29, was isolated from bread wheat (Triticum aestivum). Sequence alignment suggested that TaNAC29 might be located on chromosome 2BS. TaNAC29 was localized to the nucleus in wheat protoplasts, and proved to have transcriptional activation activities in yeast. TaNAC29 was expressed at a higher level in the leaves, and expression levels were much higher in senescent leaves, indicating that TaNAC29 might be involved in the senescence process. TaNAC29 transcripts were increased following treatments with salt, PEG6000, H2O2, and abscisic acid (ABA). To examine TaNAC29 function, transgenic Arabidopsis plants overexpressing TaNAC29 were generated. Germination and root length assays of transgenic plants demonstrated that TaNAC29 overexpression plants had enhanced tolerances to high salinity and dehydration, and exhibited an ABA-hypersensitive response. When grown in the greenhouse, TaNAC29-overexpression plants showed the same tolerance response to salt and drought stresses at both the vegetative and reproductive period, and had delayed bolting and flowering in the reproductive period. Moreover, TaNAC29 overexpression plants accumulated lesser malondialdehyde (MDA), H2O2, while had higher superoxide dismutase (SOD) and

  15. Carrier dynamics of a visible-light-responsive Ta3N5 photoanode for water oxidation

    KAUST Repository

    Ziani, Ahmed; Nurlaela, Ela; Dhawale, Dattatray Sadashiv; Silva, Diego Alves; Alarousu, Erkki; Mohammed, Omar F.; Takanabe, Kazuhiro

    2015-01-01

    The physicochemical properties of a tantalum nitride (Ta3N5) photoanode were investigated in detail to understand the fundamental aspects associated with the photoelectrochemical (PEC) water oxidation. The Ta3N5 thin films were synthesized using DC magnetron sputtering followed by annealing in air and nitridation under ammonia (NH3). A polycrystalline structure with a dense morphology of the monoclinic Ta3N5 films was obtained. A relatively low absorption coefficient (104 to 105 cm-1) in the visible light range was measured for Ta3N5, consistent with the nature of the indirect band-gap. Ultra-fast spectroscopic measurements revealed that the Ta3N5 with different thicknesses films possess low transport properties and fast carrier recombination (<10 ps). These critical kinetic properties of Ta3N5 as a photoanode may necessitate high overpotentials to achieve appreciable photocurrents for water oxidation (onset ∼0.6 V vs. RHE). This journal is

  16. Effect of Ni interlayer on diffusion bonding of a W alloy and a Ta alloy

    Energy Technology Data Exchange (ETDEWEB)

    Zhang, Jian; Liu, Ruxia; Wei, Qinqin; Luo, Guoqiang; Shen, Qiang; Zhang, Lianmeng [Wuhan Univ. of Technology (China). The State Key Lab. of Advanced Technology for Materials Synthesis and Processing

    2017-11-01

    The combination of W and Ta is expected to be highly beneficial for many applications from aerospace, weapons, military and nuclear industry. In this paper, W and Ta alloys were successfully diffusion bonded with Ni interlayer. The process of the formation of W/Ni/Ta diffusion bonded joints was investigated by means of scanning electron microscopy, X-ray diffraction system, electron probe micro-analyzer, energy dispersive spectrometry and shear strength measurement. The results show that the shear strength increases when the bonding temperature increases and exhibits a maximum value of 244 MPa at 930 C. The bonding of W/Ni can be attributed to the bonding of Ni to tungsten grains and the bonding of Ni to a Ni-Fe-binder mainly by elemental diffusion. The fracture takes place in the Ni/Ta interface and Ni{sub 3}Ta and Ni{sub 2}Ta intermetallic compounds are formed on the fracture surfaces.

  17. Ab-initio study of the hyperfine parameters in P2{sub 1}/c, P42nmc and Fm3m zirconia phases doped with Ta{sub zr} and the vacancy-Ta{sub zr} complex

    Energy Technology Data Exchange (ETDEWEB)

    Casali, R.A. [Facultad de Ciencias Exactas, y Nat. y Agr.-UNNE-Avenue Libertad 5600, Corrientes (Argentina)]. E-mail: rac@exa.unne.edu.ar; Caravaca, M.A. [Facultad de Ingenieria-UNNE, Avenue Las Heras 727, Resistencia (Argentina)

    2007-02-01

    In this work we develop selfconsistent calculations by means of the all-electron method NFP-LMTO. The electronic structure, quadrupolar frequencies and asymmetry parameters of ZrO{sub 2} polymorphs doped with Ta placed at substitutional site to Zr (Ta{sub Zr}), with and without vacancies are studied in the monoclinic, tetragonal and cubic phases. The calculated hyperfine parameters in neutral Ta{sub Zr} in the monoclinic phase are in agreement with hypine parameters measured with PAC and assigned to substitutional site in a wide range of temperatures. However, in the case of Ta{sub Zr} in the tetragonal P42nmc phase, the electric field gradient (EFG) is in large disagreement with the experimental assignment. Therefore we explored the incorporation of a near neighbor oxygen vacancy in several charged states. We found that the TaV{sup 0} and TaV{sup +1} pairs in the tetragonal symmetry with axis length ratio c/a=1.02 gives electric field gradients V{sub zz} and {eta} in agreement with low-temperature values of the experimentally assigned pure tetragonal, called t-form. Further, the pair Ta-V with a ratio c/a=1 gives EFG in close agreement with reported high-temperature values.

  18. Development of Ta3N5 as an Efficient Visible Light-responsive Photocatalyst for Water Oxidation

    KAUST Repository

    Nurlaela, Ela

    2015-09-01

    Along with many other solar energy conversion processes, research on photocatalytic water splitting to generate hydrogen and oxygen has experienced rapid major development over the past years. Developing an efficient visible-light-responsive photocatalyst has been one of the targets of such research efforts. In this regard, nitride materials, particularly Ta3N5, have been the subject of investigation due to their promising properties. This dissertation focuses on the fundamental parameters involved in the photocatalytic processes targeting overall water splitting using Ta3N5 as a model photocatalyst. The discussion primarily focuses on relevant parameters that are involved in photon absorption, exciton separation, carrier diffusion, carrier transport, and catalytic efficiency. A collection of theoretical and experimental studies of properties associated with Ta3N5 have been utilized to obtain a comprehensive understanding of this material. The fundamental structural and optoelectronic properties of Ta3N5 have been addressed. From the electronic properties, the dielectric constant and effective masses have been calculated. Because of its high dielectric constant and relatively low effective masses, Ta3N5 is promising for photocatalytic reaction applications. Studies of lattice dynamics, optical properties, and band positions have been able to clearly show that the synthesized Ta3N5 is essentially non-stoichiometric and that a truly pure phase of Ta3N5 has never been achieved, even though XRD has shown a pure phase sample. The photophysical properties of Ta3N5, such as the absorption coefficient, carrier mobility, and carrier lifetime, have been experimentally measured by synthesizing Ta3N5 thin films. Very low kinetic properties with very low transport properties and fast carrier recombination explained why overall water splitting has never been achieved with Ta3N5 as a photocatalyst to date. The extent to which the surface states of Ta3N5 photocatalysts affect

  19. Function of the auxin-responsive gene TaSAUR75 under salt and drought stress

    Directory of Open Access Journals (Sweden)

    Yuan Guo

    2018-04-01

    Full Text Available Small auxin-upregulated RNAs (SAURs are genes regulated by auxin and environmental factors. In this study, we identified a SAUR gene in wheat, TaSAUR75. Under salt stress, TaSAUR75 is downregulated in wheat roots. Subcellular localization revealed that TaSAUR75 was localized in both the cytoplasm and nucleus. Overexpression of TaSAUR75 increased drought and salt tolerance in Arabidopsis. Transgenic lines showed higher root length and survival rate and higher expression of some stress-responsive genes than control plants under salt and drought stress. Less H2O2 accumulated in transgenic lines than in control plants under drought stress. Our findings reveal a positive regulatory role of the auxin-responsive gene TaSAUR75 in plant responses to drought and salt stress and provide a candidate gene for improvement of abiotic stress tolerance in crop breeding.

  20. Kinetics of high-temperature oxidation of (Ti,Ta)(C,N)-based cermets

    International Nuclear Information System (INIS)

    Chicardi, E.; Córdoba, J.M.; Gotor, F.J.

    2016-01-01

    Highlights: • The kinetic of high-temperature oxidation of (Ti,Ta)(C,N)-Co cermets was studied. • A parabolic oxidation kinetic was determined in cermets between 700 °C and 1200 °C. • This parabolic kinetic behaviour is due to the existence of a protective layer. • The protective layer formed was a complex Ti_xTa_1_−_xO_2 oxide with rutile structure. • The oxidation rate is controlled by the Ti and O_2 diffusion through the Ti_xTa_1_−_xO_2. - Abstract: The kinetics of the high-temperature oxidation of titanium–tantalum carbonitride-based cermets with different Ti/Ta ratios was studied. Isothermal oxidation tests were conducted under static air for 48 h at temperatures between 700 °C and 1200 °C. The oxidation satisfied the parabolic kinetics, characteristic of the existence of a protective oxide layer. The apparent activation energy suggests the rate-controlling process during oxidation is the simultaneous inward and outward diffusion of oxygen and titanium, respectively, through the formed protective layer, consisting mainly of a rutile phase. A higher Ta(V) content in the rutile decreased the oxygen diffusivity due to the reduction of oxygen vacancy concentration.

  1. TiTaCN-Co cermets prepared by mechanochemical technique: microstructure and mechanical properties

    OpenAIRE

    Fides, Martin; Hvizdoš, P.; Balko, Ján; Chicardi, E.; Gotor, F.J.

    2016-01-01

    Microstructure and mechanical characterization of (Ti,Ta)(C,N)-Co based solid solution cermets prepared by two mechanochemical synthesis processes (one- and two-step milling) and a pressureless sintering in protective helium atmosphere. Materials with composition of TixTa1- xC0.5N0.5-20%Co with two different Ti/Ta ratios (x = 0.9 and x = 0.95) were developed to prepare four groups of experimental materials. Microstructures were observed using confocal microscopy and grain size was ev...

  2. Two members of TaRLK family confer powdery mildew resistance in common wheat.

    Science.gov (United States)

    Chen, Tingting; Xiao, Jin; Xu, Jun; Wan, Wentao; Qin, Bi; Cao, Aizhong; Chen, Wei; Xing, Liping; Du, Chen; Gao, Xiquan; Zhang, Shouzhong; Zhang, Ruiqi; Shen, Wenbiao; Wang, Haiyan; Wang, Xiue

    2016-01-25

    Powdery mildew, caused by Blumeria graminearum f.sp. tritici (Bgt), is one of the most severe fungal diseases of wheat. The exploration and utilization of new gene resources is the most effective approach for the powdery mildew control. We report the cloning and functional analysis of two wheat LRR-RLKs from T. aestivum c.v. Prins- T. timopheevii introgression line IGV1-465, named TaRLK1 and TaRLK2, which play positive roles in regulating powdery mildew resistance in wheat. The two LRR-RLKs contain an ORF of 3,045 nucleotides, encoding a peptide of 1014 amino acids, with seven amino acids difference. Their predicted proteins possess a signal peptide, several LRRs, a trans-membrane domain, and a Ser/Thr protein kinase domain. In response to Bgt infection, the TaRLK1/2 expression is up-regulated in a developmental-stage-dependent manner. Single-cell transient over-expression and gene-silencing assays indicate that both genes positively regulate the resistance to mixed Bgt inoculums. Transgenic lines over-expressing TaRLK1 or TaRLK2 in a moderate powdery mildew susceptible wheat variety Yangmai 158 led to significantly enhanced powdery mildew resistance. Exogenous applied salicylic acid (SA) or hydrogen peroxide (H2O2) induced the expression of both genes, and H2O2 had a higher accumulation at the Bgt penetration sites in RLK over-expression transgenic plants, suggesting a possible involvement of SA and altered ROS homeostasis in the defense response to Bgt infection. The two LRR-RLKs are located in the long arm of wheat chromosome 2B, in which the powdery mildew resistance gene Pm6 is located, but in different regions. Two members of TaRLK family were cloned from IGV1-465. TaRLK1 and TaRLK2 contribute to powdery mildew resistance of wheat, providing new resistance gene resources for wheat breeding.

  3. Overexpression of the wheat aquaporin gene, TaAQP7, enhances drought tolerance in transgenic tobacco.

    Directory of Open Access Journals (Sweden)

    Shiyi Zhou

    Full Text Available Aquaporin (AQP proteins have been shown to transport water and other small molecules through biological membranes, which is crucial for plants to combat stress caused by drought. However, the precise role of AQPs in drought stress response is not completely understood in plants. In this study, a PIP2 subgroup gene AQP, designated as TaAQP7, was cloned and characterized from wheat. Expression of TaAQP7-GFP fusion protein revealed its localization in the plasma membrane. TaAQP7 exhibited high water channel activity in Xenopus laevis oocytes and TaAQP7 transcript was induced by dehydration, and treatments with polyethylene glycol (PEG, abscisic acid (ABA and H(2O(2. Further, TaAQP7 was upregulated after PEG treatment and was blocked by inhibitors of ABA biosynthesis, implying that ABA signaling was involved in the upregulation of TaAQP7 after PEG treatment. Overexpression of TaAQP7 increased drought tolerance in tobacco. The transgenic tobacco lines had lower levels of malondialdehyde (MDA and H(2O(2, and less ion leakage (IL, but higher relative water content (RWC and superoxide dismutase (SOD and catalase (CAT activities when compared with the wild type (WT under drought stress. Taken together, our results show that TaAQP7 confers drought stress tolerance in transgenic tobacco by increasing the ability to retain water, reduce ROS accumulation and membrane damage, and enhance the activities of antioxidants.

  4. Flow synthesis of phenylserine using threonine aldolase (TA) immobilized on Eupergit support

    NARCIS (Netherlands)

    Tibhe, J.; Fu, Hui; Noel, T.; Wang, Q.; Meuldijk, J.; Hessel, V.

    2013-01-01

    Threonine aldolase (TA) from Thermotoga maritima was immobilized on Eupergit support by both a direct and an indirect method. The incubation time for the direct immobilization method was optimized for the highest amount of enzyme on the support. By introducing the immobilized TA in a packed-bed

  5. Chromosomal distribution of pTa-535, pTa-86, pTa-713, 35S rDNA repetitive sequences in interspecific hexaploid hybrids of common wheat (Triticum aestivum L. and spelt (Triticum spelta L..

    Directory of Open Access Journals (Sweden)

    Klaudia Goriewa-Duba

    Full Text Available Fluorescent in situ hybridization (FISH relies on fluorescent-labeled probes to detect specific DNA sequences in the genome, and it is widely used in cytogenetic analyses. The aim of this study was to determine the karyotype of T. aestivum and T. spelta hybrids and their parental components (three common wheat cultivars and five spelt breeding lines, to identify chromosomal aberrations in the evaluated wheat lines, and to analyze the distribution of polymorphisms of repetitive sequences in the examined hybrids. The FISH procedure was carried out with four DNA clones, pTa-86, pTa-535, pTa-713 and 35S rDNA used as probes. The observed polymorphisms between the investigated lines of common wheat, spelt and their hybrids was relatively low. However, differences were observed in the distribution of repetitive sequences on chromosomes 4A, 6A, 1B and 6B in selected hybrid genomes. The polymorphisms observed in common wheat and spelt hybrids carry valuable information for wheat breeders. The results of our study are also a valuable source of knowledge about genome organization and diversification in common wheat, spelt and their hybrids. The relevant information is essential for common wheat breeders, and it can contribute to breeding programs aimed at biodiversity preservation.

  6. Chromosomal distribution of pTa-535, pTa-86, pTa-713, 35S rDNA repetitive sequences in interspecific hexaploid hybrids of common wheat (Triticum aestivum L.) and spelt (Triticum spelta L.).

    Science.gov (United States)

    Goriewa-Duba, Klaudia; Duba, Adrian; Kwiatek, Michał; Wiśniewska, Halina; Wachowska, Urszula; Wiwart, Marian

    2018-01-01

    Fluorescent in situ hybridization (FISH) relies on fluorescent-labeled probes to detect specific DNA sequences in the genome, and it is widely used in cytogenetic analyses. The aim of this study was to determine the karyotype of T. aestivum and T. spelta hybrids and their parental components (three common wheat cultivars and five spelt breeding lines), to identify chromosomal aberrations in the evaluated wheat lines, and to analyze the distribution of polymorphisms of repetitive sequences in the examined hybrids. The FISH procedure was carried out with four DNA clones, pTa-86, pTa-535, pTa-713 and 35S rDNA used as probes. The observed polymorphisms between the investigated lines of common wheat, spelt and their hybrids was relatively low. However, differences were observed in the distribution of repetitive sequences on chromosomes 4A, 6A, 1B and 6B in selected hybrid genomes. The polymorphisms observed in common wheat and spelt hybrids carry valuable information for wheat breeders. The results of our study are also a valuable source of knowledge about genome organization and diversification in common wheat, spelt and their hybrids. The relevant information is essential for common wheat breeders, and it can contribute to breeding programs aimed at biodiversity preservation.

  7. Preparation of Ta(C)N films by pulsed high energy density plasma

    Energy Technology Data Exchange (ETDEWEB)

    Feng Wenran [Beijing National Laboratory for Condensed Matter Physics, Institute of Physics, Chinese Academy of Sciences, 100080 Beijing (China); Chen Guangliang [Beijing National Laboratory for Condensed Matter Physics, Institute of Physics, Chinese Academy of Sciences, 100080 Beijing (China); Zhang Yan [Beijing National Laboratory for Condensed Matter Physics, Institute of Physics, Chinese Academy of Sciences, 100080 Beijing (China); Gu Weichao [Beijing National Laboratory for Condensed Matter Physics, Institute of Physics, Chinese Academy of Sciences, 100080 Beijing (China); Zhang Guling [Beijing National Laboratory for Condensed Matter Physics, Institute of Physics, Chinese Academy of Sciences, 100080 Beijing (China); Niu Erwu [Beijing National Laboratory for Condensed Matter Physics, Institute of Physics, Chinese Academy of Sciences, 100080 Beijing (China); Liu Chizi [Beijing National Laboratory for Condensed Matter Physics, Institute of Physics, Chinese Academy of Sciences, 100080 Beijing (China); Yang Size [Beijing National Laboratory for Condensed Matter Physics, Institute of Physics, Chinese Academy of Sciences, 100080 Beijing (China)

    2007-04-07

    The pulsed high energy density plasma (PHEDP) is generated in the working gas due to a high-voltage high-current discharge, within a coaxial gun. In PHEDP surface modification, discharge is applied for preparing the amorphous and nanostructured high-melting materials as thin films deposited on various substrates. In this investigation, Ta(C)N films were deposited using PHEDP on stainless steel. Pure tantalum and graphite were used as the inner and outer electrodes of the PHEDP coaxial gun, respectively. Nitrogen was used as the working gas and also one of the reactants. Preliminary study on the films prepared under different conditions shows that the formation of Ta(C)N is drastically voltage dependent. At lower gun voltage, no Ta(C)N was detected in the films; when the gun voltage reaches or exceeds 3.0 kV, Ta(C)N occurred. The films are composed of densely stacked nanocrystallines with diameter less than 30 nm, and some grains are within 10 nm in diameter.

  8. Crystal structure of the mixed-metal trisulfide BaCu1/3Ta2/3S3

    Directory of Open Access Journals (Sweden)

    Kejun Bu

    2017-05-01

    Full Text Available The mixed-metal title compound, BaCu1/3Ta2/3S3 [barium copper(II tantalum(V trisulfide], was prepared through solid-state reactions. The crystal structure adopts the BaTaS3 structure type and consists of face-sharing [MS6] (M = Ta,Cu octahedra (point-group symmetry -3m. that are condensed into infinite chains along [001]. Adjacent chains are linked through the barium cations (site symmetry -6m2, which exhibit a coordination number of twelve. The M site is occupied by 2/3 of TaV and 1/3 of CuII, whereby the average M—S distances are slightly longer than those of ordered BaTaS3. The classical charge balance of the title compound can be represented by [Ba2+] [(Ta/Cu4+] [S2−]3.

  9. TDPAC characterization of tin oxides using 181Ta

    International Nuclear Information System (INIS)

    Moreno, M.S.; Desimoni, J.; Requejo, F.G.; Renteria, M.; Bibiloni, A.G.

    1991-01-01

    In connection with a general study of the evolution of tin-oxygen thin films, we report here on the hyperfine interactions of 181 Ta substitutionally replacing tin in the isolated phases SnO and SnO 2 . For this purpose, pure SnO pressed powder and a thin SnO 2 film were implanted with 181 Hf. In both cases, unique quadrupole frequencies were found after thermal annealing treatments. The results indicate that the following hyperfine parameters: ν Q =740.6(2.1) MHz, η=0.07(2) and ν Q =971.5(1.9) MHz, η=0.72(1) characterize 181 Ta and SnO and SnO 2 , respectively. (orig.)

  10. Low elastic modulus Ti–Ta alloys for load-bearing permanent implants: Enhancing the biodegradation resistance by electrochemical surface engineering

    Energy Technology Data Exchange (ETDEWEB)

    Kesteven, Jazmin [Biomaterials and Engineering Materials (BEM) Laboratory, School of Engineering and Physical Sciences, James Cook University, Townsville, Queensland 4811 (Australia); Kannan, M. Bobby, E-mail: bobby.mathan@jcu.edu.au [Biomaterials and Engineering Materials (BEM) Laboratory, School of Engineering and Physical Sciences, James Cook University, Townsville, Queensland 4811 (Australia); Walter, Rhys; Khakbaz, Hadis [Biomaterials and Engineering Materials (BEM) Laboratory, School of Engineering and Physical Sciences, James Cook University, Townsville, Queensland 4811 (Australia); Choe, Han-Choel [Department of Dental Materials, Chosun University, Gwangju 501-759 (Korea, Republic of)

    2015-01-01

    In this study, the in vitro degradation behaviour of titanium–tantalum (Ti–Ta) alloys (10–30 wt.% Ta) was investigated and compared with conventional implant materials, i.e., commercially pure titanium (Cp-Ti) and titanium–aluminium–vanadium (Ti6Al4V) alloy. Among the three Ti–Ta alloys studied, the Ti20Ta (6.3 × 10{sup −4} mm/y) exhibited the lowest degradation rate, followed by Ti30Ta (1.2 × 10{sup −3} mm/y) and Ti10Ta (1.4 × 10{sup −3} mm/y). All the Ti–Ta alloys exhibited lower degradation rate than that of Cp-Ti (1.8 × 10{sup −3} mm/y), which suggests that Ta addition to Ti is beneficial. As compared to Ti6Al4V alloy (8.1 × 10{sup −4} mm/y), the degradation rate of Ti20Ta alloy was lower by ∼ 22%. However, the Ti30Ta alloy, which has closer elastic modulus to that of natural bone, showed ∼ 48% higher degradation rate than that of Ti6Al4V alloy. Hence, to improve the degradation performance of Ti30Ta alloy, an intermediate thin porous layer was formed electrochemically on the alloy followed by calcium phosphate (CaP) electrodeposition. The coated Ti30Ta alloy (3.8 × 10{sup −3} mm/y) showed ∼ 53% lower degradation rate than that of Ti6Al4V alloy. Thus, the study suggests that CaP coated Ti30Ta alloy can be a viable material for load-bearing permanent implants. - Highlights: • In vitro degradation of titanium–tantalum (Ti–Ta) alloys was studied. • Ta addition to Ti is beneficial for better degradation resistance. • Ti–Ta alloys perform better than commercially pure Ti. • Calcium phosphate coated Ti–Ta alloy is superior to Ti6Al4V alloy.

  11. New TA Index-Based Rollover Prevention System for Electric Vehicles

    OpenAIRE

    Xiang Liu; Min Xu; Mian Li

    2015-01-01

    In addition to clean transportation and energy savings, electric vehicles can inherently offer better performance in the field of active safety and dynamic stability control, thanks to the superior fast and accurate control characteristics of electric motors. With the novel wheel status parameter TA for electric vehicles proposed by the authors in an earlier publication, a new TA index (TAI)-based rollover prevention method is presented in this paper to improve the driving performance of EV...

  12. Enhanced photoactivity from single-crystalline SrTaO2N nanoplates synthesized by topotactic nitridation

    International Nuclear Information System (INIS)

    Fu, Jie; Skrabalak, Sara E.

    2017-01-01

    There are few methods yielding oxynitride crystals with defined shape, yet shape-controlled crystals often give enhanced photoactivity. Herein, single-crystalline SrTaO 2 N nanoplates and polyhedra are achieved selectively. Central to these synthetic advances is the crystallization pathways used, in which single-crystalline SrTaO 2 N nanoplates form by topotactic nitridation of aerosol-prepared Sr 2 Ta 2 O 7 nanoplates and SrTaO 2 N polyhedra form by flux-assisted nitridation of the nanoplates. Evaluation of these materials for the oxygen evolution reaction (OER) and hydrogen evolution reaction (HER) showed improved performance for the SrTaO 2 N nanoplates, with a record apparent quantum efficiency (AQE) of 6.1 % for OER compared to the polyhedra (AQE: 1.6 %) and SrTaO 2 N polycrystals (AQE: 0.6 %). The enhanced performance from the nanoplates arises from their morphology and lower defect density. These results highlight the importance of developing new synthetic routes to high quality oxynitrides. (copyright 2017 Wiley-VCH Verlag GmbH and Co. KGaA, Weinheim)

  13. Enhanced Photoactivity from Single-Crystalline SrTaO2 N Nanoplates Synthesized by Topotactic Nitridation.

    Science.gov (United States)

    Fu, Jie; Skrabalak, Sara E

    2017-11-06

    There are few methods yielding oxynitride crystals with defined shape, yet shape-controlled crystals often give enhanced photoactivity. Herein, single-crystalline SrTaO 2 N nanoplates and polyhedra are achieved selectively. Central to these synthetic advances is the crystallization pathways used, in which single-crystalline SrTaO 2 N nanoplates form by topotactic nitridation of aerosol-prepared Sr 2 Ta 2 O 7 nanoplates and SrTaO 2 N polyhedra form by flux-assisted nitridation of the nanoplates. Evaluation of these materials for the oxygen evolution reaction (OER) and hydrogen evolution reaction (HER) showed improved performance for the SrTaO 2 N nanoplates, with a record apparent quantum efficiency (AQE) of 6.1 % for OER compared to the polyhedra (AQE: 1.6 %) and SrTaO 2 N polycrystals (AQE: 0.6 %). The enhanced performance from the nanoplates arises from their morphology and lower defect density. These results highlight the importance of developing new synthetic routes to high quality oxynitrides. © 2017 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

  14. Electric Properties of NaTaO3 Obtained by Hydrothermal Method

    Science.gov (United States)

    Malaescu, Dan; Grozescu, Ioan; Sfirloaga, Paula; Vlazan, Paulina; Marin, Catalin N.

    2015-12-01

    Two samples of NaTaO3 perovskite materials were prepared by the standard hydrothermal method at the same reaction temperature (600 °C) but with different sintering times: 6 hours for sample S1 and 12 hours for sample S2. Using X-ray diffraction (XRD), it shows that samples S1 and S2 are mixtures of Na-Ta oxides (Ta2O5 and the prevailing phase NaTaO3). The scanning electron microscopy analysis (SEM), shows that the grains are connected each other in agglomerated clusters of size about few hundred nanometers. The frequency (f) dependencies of complex impedance, Z(f) = Z'(f) - i Z''(f) of the samples, over the frequency range 20 Hz - 2 MHz, at room temperature are presented. The real component Z' of the complex impedance decreases with increasing frequency and the imaginary component Z'' has two maximum corresponding to two relaxation processes. The results obtained from the complex impedance spectroscopy, Z''(Z') showed the appearance of two semicircles, corresponding to grain and grain boundary mechanism. Experimental results have been fitted with two parallel RC equivalent circuits connected in series and the parameters R and C have been evaluated.

  15. Structural evolution of a Ta-filament during hot-wire chemical vapour deposition of Silicon investigated by electron backscatter diffraction

    CSIR Research Space (South Africa)

    Oliphant, CJ

    2012-03-01

    Full Text Available , encapsulating a Ta inner core. The tantalum rich Ta5Si3, Si3Ta5 and Ta2Si phases however formed in addition to TaSi2 at the centre regions. Cracks and porosity were found throughout the length of the filament. The microstructure evolution of the aged tantalum...

  16. Superconductivity of Hg3NbF6 and Hg3TaF6

    International Nuclear Information System (INIS)

    Datars, W.R.; Morgan, K.R.; Gillespie, R.J.

    1983-01-01

    Low-temperature ac susceptibility measurements show that two new metallic compounds, Hg 3 TaF 6 and Hg 3 NbF 6 , are superconductors with a critical temperature of 7.0 K. Critical fields are 20% higher in Hg 3 TaF 6 but the temperature dependence of the critical field of the compounds is very similar down to 1.35 K. The critical field extrapolated to T = 0 K is 0.17 T for Hg 3 TaF 6 and 0.13 T for Hg 3 NbF 6

  17. Laser Spectroscopy and AB Initio Calculations on the TaF Molecule

    Science.gov (United States)

    Ng, Kiu Fung; Zou, Wenli; Liu, Wenjian; Cheung, Allan S. C.

    2016-06-01

    Electronic transition spectrum of the tantalum monoflouride (TaF) molecule in the spectral region between 448 and 520 nm has been studied using the technique of laser-ablation/reaction free jet expansion and laser induced fluorescence spectroscopy. TaF molecule was produced by reacting laser-ablated tantalum atoms with sulfur hexafluoride gas seeded in argon. Sixteen vibrational bands with resolved rotational structure have been recorded and analyzed, which were organized into six electronic transition systems and the ground state has been identified to be the X3Σ-(0+) state with bond length, ro, and equilibrium vibrational frequency, ωe, determined to be 1.8209 Å and 700.1 wn respectively. In addition, four vibrational bands belong to another transition system involving lower state with Ω = 2 component has also been analyzed. All observed transitions are with ΔΩ = 0. Least-squares fit of the measured line positions yielded molecular constants for the electronic states involved. The Λ-S and Ω states of TaF were calculated at the state-averaged complete active space self-consistent field (SA-CASSCF) and the subsequent internally contracted multi-reference configuration interaction with singles and doubles and Davidson's cluster correction (MRCISD+Q) levels of theory with the active space of 4 electrons in 6 orbitals, that is, the molecular orbitals corresponding to Ta 5d6s are active. The spin-orbit coupling (SOC) is calculated by the state-interaction approach at the SA-CASSCF level via the relativistic effective core potentials (RECPs) spin-orbit operator, where the diagonal elements of the spin-orbit matrix are replaced by the above MRCISD+Q energies. The spectroscopic properties of the ground and many low-lying electronic states of the TaF molecule will be reported. With respect to the observed electronic states in this work, the calculated results are in good agreement with our experimental determinations. This work represents the first experimental

  18. 78 FR 41954 - TA-W-82,634, Prudential Global Business Technology Solutions Central Security Services Dresher...

    Science.gov (United States)

    2013-07-12

    ... Business Technology Solutions Central Security Services Iselin, New Jersey; TA-W-82,634B, Prudential Global Business Technology Solutions Central Security Services Plymouth, Minnesota; TA- W-82,634C, Prudential Global Business Technology Solutions Central Security Services Scottsdale, Arizona; TA-W-82,634D...

  19. Effect of TaC addition on the microstructures and mechanical properties of Ti(C, N)-based cermets

    International Nuclear Information System (INIS)

    Wu, Peng; Zheng, Yong; Zhao, Yongle; Yu, Haizhou

    2010-01-01

    The microstructures of the prepared Ti(C, N)-based cermets with various TaC additions were studied using X-ray diffractometry (XRD) and scanning electron microscopy (SEM). Mechanical properties such as transverse rupture strength (TRS), fracture toughness (K 1C ) and hardness (HRA) were also measured. The results showed that the grain size of the cermets decreased with increasing TaC addition, but too high TaC addition resulted in agglomeration of the grains. An increasing TaC addition increased the dissolution of tungsten, titanium, molybdenum and tantalum in the binder phase. The hardness of the cermets decreased slightly with increasing TaC addition. The transverse rupture strength was the highest for the cermets with 5 wt.% TaC addition, which was characterized by fine grains, homogeneous microstructure and the moderate thickness of rim phase in the binder. The fracture toughness of the cermets with TaC addition from 0 to 5 wt.% decreased obviously, which resulting from decreased grain size. The further decreasing of fracture toughness for the cermets with 7 wt.% TaC addition was due to increased porosity and interfacial tensile stress.

  20. Utility of tantalum (Ta) coating to improve surface hardness in vitro bioactivity and biocompatibility of Co–Cr

    Energy Technology Data Exchange (ETDEWEB)

    Pham, Vuong-Hung [WCU Hybrid Materials Program, Department of Materials Science and Engineering, Seoul National University, Seoul, 151-742 (Korea, Republic of); Advanced Institute for Science and Technology (AIST), Hanoi University of Science and Technology (HUST), No 1, Dai Co Viet Road, Ha Noi (Viet Nam); Lee, Seung-Hee; Li, Yuanlong; Kim, Hyoun-Ee [WCU Hybrid Materials Program, Department of Materials Science and Engineering, Seoul National University, Seoul, 151-742 (Korea, Republic of); Shin, Kwan-Ha [Department of Dental Laboratory Science and Engineering, Korea University, Seoul, 136-703 (Korea, Republic of); Koh, Young-Hag, E-mail: kohyh@korea.ac.kr [Department of Dental Laboratory Science and Engineering, Korea University, Seoul, 136-703 (Korea, Republic of)

    2013-06-01

    This study reports the utility of tantalum (Ta) coating for improving the surface hardness, in vitro bioactivity and biocompatibility of Co–Cr implants. The use of direct current sputtering allowed for the deposition of a dense and uniform Ta film onto a Co–Cr substrate, which was composed of β-phase Ta grains. This hard Ta coating significantly improved the surface hardness of the Co–Cr by a factor of > 2.3. In addition, the Ta-deposited Co–Cr substrate showed a vigorous precipitation of apatite crystals on its surface after 4 weeks of immersion in simulated body fluid, suggesting its excellent in vitro bioactivity. This bioactive Ta coating led to a considerable improvement in the in vitro biocompatibility of the Co–Cr, which was assessed in terms of the attachment, proliferation and differentiation of pre-osteoblasts (MC3T3-E1). - Highlights: • Dense and uniform Ta film was deposited onto a Co–Cr substrate using DC sputtering. • The Ta coating significantly enhanced the surface hardness of the Co–Cr. • The in vitro biocompatibility of the Co–Cr was also significantly improved.

  1. Utility of tantalum (Ta) coating to improve surface hardness in vitro bioactivity and biocompatibility of Co–Cr

    International Nuclear Information System (INIS)

    Pham, Vuong-Hung; Lee, Seung-Hee; Li, Yuanlong; Kim, Hyoun-Ee; Shin, Kwan-Ha; Koh, Young-Hag

    2013-01-01

    This study reports the utility of tantalum (Ta) coating for improving the surface hardness, in vitro bioactivity and biocompatibility of Co–Cr implants. The use of direct current sputtering allowed for the deposition of a dense and uniform Ta film onto a Co–Cr substrate, which was composed of β-phase Ta grains. This hard Ta coating significantly improved the surface hardness of the Co–Cr by a factor of > 2.3. In addition, the Ta-deposited Co–Cr substrate showed a vigorous precipitation of apatite crystals on its surface after 4 weeks of immersion in simulated body fluid, suggesting its excellent in vitro bioactivity. This bioactive Ta coating led to a considerable improvement in the in vitro biocompatibility of the Co–Cr, which was assessed in terms of the attachment, proliferation and differentiation of pre-osteoblasts (MC3T3-E1). - Highlights: • Dense and uniform Ta film was deposited onto a Co–Cr substrate using DC sputtering. • The Ta coating significantly enhanced the surface hardness of the Co–Cr. • The in vitro biocompatibility of the Co–Cr was also significantly improved

  2. Confronting passive behavior through outdoor experience: a TA approach to experiential learning

    Science.gov (United States)

    Frederick W. Medrick

    1977-01-01

    The concepts and techniques of transactional analysis (TA) can usefully be applied to outdoor challenge programs aimed at facilitating personal growth, developing responsibility, and teaching cooperative behavior. Passive behavior results from discounting of the self and others; four levels of it have been identified, and TA offers various means of preventing or...

  3. From single-site tantalum complexes to nanoparticles of Ta x N y and TaO x N y supported on silica: elucidation of synthesis chemistry by dynamic nuclear polarization surface enhanced NMR spectroscopy and X-ray absorption spectroscopy.

    Science.gov (United States)

    Mohandas, Janet C; Abou-Hamad, Edy; Callens, Emmanuel; Samantaray, Manoja K; Gajan, David; Gurinov, Andrei; Ma, Tao; Ould-Chikh, Samy; Hoffman, Adam S; Gates, Bruce C; Basset, Jean-Marie

    2017-08-01

    Air-stable catalysts consisting of tantalum nitride nanoparticles represented as a mixture of Ta x N y and TaO x N y with diameters in the range of 0.5 to 3 nm supported on highly dehydroxylated silica were synthesized from TaMe 5 (Me = methyl) and dimeric Ta 2 (OMe) 10 with guidance by the principles of surface organometallic chemistry (SOMC). Characterization of the supported precursors and the supported nanoparticles formed from them was carried out by IR, NMR, UV-Vis, extended X-ray absorption fine structure, and X-ray photoelectron spectroscopies complemented with XRD and high-resolution TEM, with dynamic nuclear polarization surface enhanced NMR spectroscopy being especially helpful by providing enhanced intensities of the signals of 1 H, 13 C, 29 Si, and 15 N at their natural abundances. The characterization data provide details of the synthesis chemistry, including evidence of (a) O 2 insertion into Ta-CH 3 species on the support and (b) a binuclear to mononuclear transformation of species formed from Ta 2 (OMe) 10 on the support. A catalytic test reaction, cyclooctene epoxidation, was used to probe the supported nanoparticles, with 30% H 2 O 2 serving as the oxidant. The catalysts gave selectivities up to 98% for the epoxide at conversions as high as 99% with a 3.4 wt% loading of Ta present as Ta x N y /TaO x N y .

  4. Exfoliation and van der Waals heterostructure assembly of intercalated ferromagnet Cr1/3TaS2

    Science.gov (United States)

    Yamasaki, Yuji; Moriya, Rai; Arai, Miho; Masubuchi, Satoru; Pyon, Sunseng; Tamegai, Tsuyoshi; Ueno, Keiji; Machida, Tomoki

    2017-12-01

    Ferromagnetic van der Waals (vdW) materials are in demand for spintronic devices with all-two-dimensional-materials heterostructures. Here, we demonstrate mechanical exfoliation of magnetic-atom-intercalated transition metal dichalcogenide Cr1/3TaS2 from its bulk crystal; previously such intercalated materials were thought difficult to exfoliate. Magnetotransport in exfoliated tens-of-nanometres-thick flakes revealed ferromagnetic ordering below its Curie temperature T C ~ 110 K as well as strong in-plane magnetic anisotropy; these are identical to its bulk properties. Further, van der Waals heterostructure assembly of Cr1/3TaS2 with another intercalated ferromagnet Fe1/4TaS2 is demonstrated using a dry-transfer method. The fabricated heterojunction composed of Cr1/3TaS2 and Fe1/4TaS2 with a native Ta2O5 oxide tunnel barrier in between exhibits tunnel magnetoresistance (TMR), revealing possible spin injection and detection with these exfoliatable ferromagnetic materials through the vdW junction.

  5. Nanodiamond embedded ta-C composite film by pulsed filtered vacuum arc deposition from a single target

    Science.gov (United States)

    Iyer, Ajai; Etula, Jarkko; Ge, Yanling; Liu, Xuwen; Koskinen, Jari

    2016-11-01

    Detonation Nanodiamonds (DNDs) are known to have sp3 core, sp2 shell, small size (few nm) and are gaining importance as multi-functional nanoparticles. Diverse methods have been used to form composites, containing detonation nanodiamonds (DNDs) embedded in conductive and dielectric matrices for various applications. Here we show a method, wherein DND-ta-C composite film, consisting of DNDs embedded in ta-C matrix have been co-deposited from the same cathode by pulsed filtered cathodic vacuum arc method. Transmission Electron Microscope analysis of these films revel the presence of DNDs embedded in the matrix of amorphous carbon. Raman spectroscopy indicates that the presence of DNDs does not adversely affect the sp3 content of DND-ta-C composite film compared to ta-C film of same thickness. Nanoindentation and nanowear tests indicate that DND-ta-C composite films possess improved mechanical properties in comparison to ta-C films of similar thickness.

  6. The Wheat Bax Inhibitor-1 Protein Interacts with an Aquaporin TaPIP1 and Enhances Disease Resistance in Arabidopsis

    Directory of Open Access Journals (Sweden)

    Pan-Pan Lu

    2018-01-01

    Full Text Available Bax inhibitor-1 (BI-1 is an endoplasmic reticulum (ER-resident cell death suppressor evolutionarily conserved in eukaryotes. The ability of BI-1 to inhibit the biotic and abiotic stresses have been well-studied in Arabidopsis, while the functions of wheat BI-1 are largely unknown. In this study, the wheat BI-1 gene TaBI-1.1 was isolated by an RNA-seq analysis of Fusarium graminearum (Fg-treated wheat. TaBI-1.1 expression was induced by a salicylic acid (SA treatment and down-regulated by an abscisic acid (ABA treatment. Based on β-glucuronidase (GUS staining, TaBI-1.1 was expressed in mature leaves and roots but not in the hypocotyl or young leaves. Constitutive expression of TaBI-1.1 in Arabidopsis enhanced its resistance to Pseudomonas syringae pv. Tomato (Pst DC3000 infection and induced SA-related gene expression. Additionally, TaBI-1.1 transgenic Arabidopsis exhibited an alleviation of damage caused by high concentrations of SA and decreased the sensitivity to ABA. Consistent with the phenotype, the RNA-seq analysis of 35S::TaBI-1.1 and Col-0 plants showed that TaBI-1.1 was involved in biotic stresses. These results suggested that TaBI-1.1 positively regulates SA signals and plays important roles in the response to biotic stresses. In addition, TaBI-1.1 interacted with the aquaporin TaPIP1, and both them were localized to ER membrane. Furthermore, we demonstrated that TaPIP1 was up-regulated by SA treatment and TaPIP1 transgenic Arabidopsis enhanced the resistance to Pst DC3000 infection. Thus, the interaction between TaBI-1.1 and TaPIP1 on the ER membrane probably occurs in response to SA signals and defense response.

  7. A study on the microstructure of Pt/TaN/Si films by high resolution TEM analysis

    CERN Document Server

    Cho, K N; Oh, J E; Park, C S; Lee, S I; Lee, M Y

    1998-01-01

    The microstructure change of Pt/amorphous TaN/Si films after various heat treatments has been investigated by high resolution transmission electron microscopy (HR-TEM) analysis. TaN thin films are deposited by remote plasma metalorganic chemical vapor deposition (RP-MOCVD) using pentakis-dimethyl-amino-tantalum (PDMATa) and radical sources, hydrogen and ammonia plasma. Deposited TaN thin film shows excellent barrier properties such as good resistance against oxidation after post-heat treatment at high temperature. In the case of hydrogen plasma, however, diffusion of Pt into TaN layer was observed, which was caused by the out-diffusion of carbon through the grain boundaries of Pt. In the case of ammonia plasma, the formation of thin oxide layer at the Pt/TaN interface was observed.

  8. Project Ta-kos Outreach. Final Report.

    Science.gov (United States)

    Askew, Linda; And Others

    The Project Ta-kos Outreach program is an inservice training model designed to increase the probability that children (ages birth to 8) at risk for or with special needs and their families can access and receive appropriate services in order to remain an integral part of the community in which they reside. The program reflects an ecological…

  9. Wheat F-Box Protein Gene TaFBA1 Is Involved in Plant Tolerance to Heat Stress

    Directory of Open Access Journals (Sweden)

    Qinxue Li

    2018-04-01

    Full Text Available Adverse environmental conditions, including high temperature, often affect the growth and production of crops worldwide. F-box protein, a core component of the Skp1-Cullin-F-box (SCF E3 ligase complex, plays an important role in abiotic stress responses. A previously cloned gene from wheat, TaFBA1, encodes a homologous F-box protein. A Yeast two-Hybrid (Y2H assay showed that TaFBA1 interacted with other SCF proteins. We found that the expression of TaFBA1 could be induced by heat stress (45°C. Overexpression of TaFBA1 enhanced heat stress tolerance in transgenic tobacco, because growth inhibition was reduced and photosynthesis increased as compared with those in the wild type (WT plants. Furthermore, the accumulation of H2O2, O2-, and carbonyl protein decreased and cell damage was alleviated in transgenic plants under heat stress, which resulted in less oxidative damage. However, the transgenic plants contained more enzymatic antioxidants after heat stress, which might be related to the regulation of some antioxidant gene expressions. The qRT-PCR analysis showed that the overexpression of TaFBA1 upregulated the expression of genes involved in reactive oxygen species (ROS scavenging, proline biosynthesis, and abiotic stress responses. We identified the interaction of TaFBA1 with Triticum aestivum stress responsive protein 1 (TaASRP1 by Y2H assay and bimolecular fluorescence complementation (BiFC assay. The results suggested that TaFBA1 may improve enzymatic antioxidant levels and regulate gene expression by interacting with other proteins, such as TaASRP1, which leads to the enhanced heat stress tolerance seen in the transgenic plants.

  10. A wheat calreticulin gene (TaCRT1) contributes to drought tolerance in transgenic arabidopsis

    International Nuclear Information System (INIS)

    Xiang, V.; Du, C.; Jia, H.; Song, M.; Wang, Y.; Ma, Z.

    2018-01-01

    The TaCRT1 gene is a member of calreticulin (CRT) family in wheat. In our previous study, we showed that transgenic tobacco lines over expressing wheat TaCRT1 showed enhanced tolerance to salt stress. This study aimed to determine whether TaCRT1 over expression would increase drought tolerance in transgenic Arabidopsis. Over expression of TaCRT1 in Arabidopsis plants enhances tolerance to drought stress. However, the transgenic line was found to retard the growth. Moreover, the transgenic line showed decreased water loss but higher sensitivity to exogenous abscisic acid (ABA) compared with the wild type (Col-0). Meanwhile, the transgenic line had the elevated endogenous ABA level. The semi-quantitative RT-PCR (sqRT-PCR) analysis showed that transcription levels of ABA-biosynthesizing gene (NCED3) and ABA-responsive gene (ABF3) were higher in the transgenic line than that in the Col-0 under normal condition. The above results implied that the TaCRT1 might be able to used as a potential target to improve the drought tolerance in crops. (author)

  11. Study on electrical defects level in single layer two-dimensional Ta2O5

    Science.gov (United States)

    Dahai, Li; Xiongfei, Song; Linfeng, Hu; Ziyi, Wang; Rongjun, Zhang; Liangyao, Chen; David, Wei Zhang; Peng, Zhou

    2016-04-01

    Two-dimensional atomic-layered material is a recent research focus, and single layer Ta2O5 used as gate dielectric in field-effect transistors is obtained via assemblies of Ta2O5 nanosheets. However, the electrical performance is seriously affected by electronic defects existing in Ta2O5. Therefore, spectroscopic ellipsometry is used to calculate the transition energies and corresponding probabilities for two different charged oxygen vacancies, whose existence is revealed by x-ray photoelectron spectroscopy analysis. Spectroscopic ellipsometry fitting also calculates the thickness of single layer Ta2O5, exhibiting good agreement with atomic force microscopy measurement. Nondestructive and noncontact spectroscopic ellipsometry is appropriate for detecting the electrical defects level of single layer Ta2O5. Project supported by the National Natural Science Foundation of China (Grant Nos. 11174058 and 61376093), the Fund from Shanghai Municipal Science and Technology Commission (Grant No. 13QA1400400), the National Science and Technology Major Project, China (Grant No. 2011ZX02707), and the Innovation Program of Shanghai Municipal Education Commission (Grant No. 12ZZ010).

  12. Modified Ta/MCM-41 catalysts for enantioselective oxidation of thioanisole

    OpenAIRE

    Fadhli, Marwa; Khedher, Ilyes; Fraile, José M.

    2015-01-01

    Ta-MCM41 catalysts have been prepared by grafting of Ta(OEt)5 on MCM41, pre-calcined at three different temperatures (550, 650 and 750 °C). These solids have been modified with two chiral ligands: R-(+)-diethyl l-tartrate (DET) and R-(+)-diisopropyl l-tartrate (DIPT). The formation of the chiral tantalum species and their influence on the structure of MCM41 have been studied by several characterization techniques, such as XRD, FTIR, N2 adsorption isotherms and MAS NMR. The grafted tantalum sp...

  13. An oxotantalate with network-type structure: Cs3Ta5O14

    International Nuclear Information System (INIS)

    Serafin, M.; Hoppe, R.

    1982-01-01

    Cs 3 Ta 5 O 14 was obtained for the first time as colourless single crystals, orthorhombic, a = 26.235(2), b = 7.429(1), c = 7.388(1) A, Z = 4, space group Pbam. According to four-circle-diffractometer data (1521 hkl, F 0 > 1.5 σ(F 0 ), 3 0 0 , R = 10%) it crystallizes with a complicated network-type structure. Ta is partly in an octahedral (C.N.6), partly in a trigonal-bipyramidal (C.N.5) environment. The [Ta 5 O 14 ] network contains channels occupied by Cs. Effective Coordination Numbers, ECoN, and the Madelung Part of the Lattice Energy, MAPLE, have been calculated and are discussed. (author)

  14. InTaO4-based nanostructures synthesized by reactive pulsed laser ablation

    International Nuclear Information System (INIS)

    Yoshida, Takehito; Toyoyama, Hirokazu; Umezu, Ikurou; Sugimura, Akira

    2008-01-01

    Nanostructured Ni-doped indium-tantalum-oxides (InTaO 4 ) were synthesized by a reactive pulsed laser ablation process, aiming at the final goal of direct splitting of water under visible sunbeam irradiation. The third harmonics beam of a Nd:YAG laser was focused onto a sintered In 0.9 Ni 0.1 TaO 4-δ target in pure oxygen background gases (0.05-1.00 Torr). Increasing the oxygen gas pressure, via thin films having nanometer-sized strong morphologies, single-crystalline nanoparticles were synthesized in the reactive vapor phases. The nanostructured deposited materials have the monoclinic layered wolframite-type structure of bulk InTaO 4 , without oxygen deficiency. (orig.)

  15. Produksi Hidrogen Secara Fotokalitik dari Air Murni Pada Katalis NaTaO3

    Directory of Open Access Journals (Sweden)

    Husni Husin

    2012-12-01

    Full Text Available Study of hydrogen production as a green energy on NaTaO3 photocatalyst has been done. The aim of this work is to study the photocatalytic properties of NaTaO3 and NiO incorporated NaTaO3 used in water splitting reaction. The NaTaO3 powder with high crystallinity has been synthesized by a H2O2-asissted sol-gel route calcined at a temperature of 900 oC. NiO as a cocatalyst is deposited by impregnation of Ni(NO32.6H2O solution. The catalysts are characterized by X-ray diffraction (XRD, scanning electron microscopy (SEM, high resolution transmission electron microscopy (HRTEM, and diffuse reflectance UV-Vis (DR-UV-Vis. The photocatalysts have a band gap energy ca. 4.01 and 4.00 eV (corresponding to absorption edge of 310 and 311 nm. Photocatalytic activity towards hydrogen generation from water is investigated using a glass reactor under ultra violet (UV light illumination. Photocatalytic of H2 and O2 production on the pristine NaTaO3 are 0.61 and 0.30 mmol g-1 cat.h-1, respectively. The activities are greatly enhanced 8.5 times higher by the incorporation of NiO as cocatalysts on the prepared oxides. NiO is found to give rise to more efficient photocatalytic activity for hydrogen evolution. The NaTaO3 nanoparticles produces using this facile have: better crystallinity, smaller size, and higher photocatalytic activity. Keywords: Sodium tantalum oxide; Nickel oxide; Sol-gel; impregnation; Hydrogen evolution

  16. Low elastic modulus Ti-Ta alloys for load-bearing permanent implants: enhancing the biodegradation resistance by electrochemical surface engineering.

    Science.gov (United States)

    Kesteven, Jazmin; Kannan, M Bobby; Walter, Rhys; Khakbaz, Hadis; Choe, Han-Choel

    2015-01-01

    In this study, the in vitro degradation behaviour of titanium-tantalum (Ti-Ta) alloys (10-30 wt.% Ta) was investigated and compared with conventional implant materials, i.e., commercially pure titanium (Cp-Ti) and titanium-aluminium-vanadium (Ti6Al4V) alloy. Among the three Ti-Ta alloys studied, the Ti20Ta (6.3×10(-4) mm/y) exhibited the lowest degradation rate, followed by Ti30Ta (1.2×10(-3) mm/y) and Ti10Ta (1.4×10(-3) mm/y). All the Ti-Ta alloys exhibited lower degradation rate than that of Cp-Ti (1.8×10(-3) mm/y), which suggests that Ta addition to Ti is beneficial. As compared to Ti6Al4V alloy (8.1×10(-4) mm/y), the degradation rate of Ti20Ta alloy was lower by ~22%. However, the Ti30Ta alloy, which has closer elastic modulus to that of natural bone, showed ~48% higher degradation rate than that of Ti6Al4V alloy. Hence, to improve the degradation performance of Ti30Ta alloy, an intermediate thin porous layer was formed electrochemically on the alloy followed by calcium phosphate (CaP) electrodeposition. The coated Ti30Ta alloy (3.8×10(-3) mm/y) showed ~53% lower degradation rate than that of Ti6Al4V alloy. Thus, the study suggests that CaP coated Ti30Ta alloy can be a viable material for load-bearing permanent implants. Copyright © 2014 Elsevier B.V. All rights reserved.

  17. Laser stimulated third harmonic generation studies in ZnO-Ta2O5-B2O3 glass ceramics entrenched with Zn3Ta2O8 crystal phases

    Science.gov (United States)

    Siva Sesha Reddy, A.; Jedryka, J.; Ozga, K.; Ravi Kumar, V.; Purnachand, N.; Kityk, I. V.; Veeraiah, N.

    2018-02-01

    In this study zinc borate glasses doped with different concentrations Ta2O5 were synthesized and were crystallized by heat treatment for prolonged times. The samples were characterized by XRD, SEM, IR and Raman spectroscopy techniques. The SEM images of the crystallized samples have indicated that the samples contain randomly distributed crystal grains with size ∼1 μm entrenched in the residual amorphous phase. XRD studies have exhibited diffraction peaks identified as being due to the reflections from (1 1 1) planes of monoclinic Zn3Ta2O8 crystal phase that contains intertwined tetrahedral zinc and octahedral tantalate structural units. The concentration of such crystal phases in the bulk samples is observed to increase with increase of Ta2O5 up to 3.0 mol%. The IR and Raman spectroscopy studies have confirmed the presence of ZnO4 and TaO6 structural units in the glass network in addition to the conventional borate structural units. For measuring third harmonic generation (THG) in the samples, the samples were irradiated with 532 nm laser beam and the intensity of THG of probing beam (Nd:YAG λ = 1064 nm 20 ns pulsed laser (ω)) is measured as a function of fundamental beam power varying up to 200 J/m2. The intensity of THG is found to be increasing with increase of fundamental beam power and found to be the maximal for the glass crystallized with 3.0 mol% of Ta2O5. The intensity of THG of the ceramicized samples is found to be nearly 5 times higher with respect to that of pre-crystallized samples. The generation of 3ω is attributed to the perturbation/interaction between Zn3Ta2O8 anisotropic crystal grains and the incident probing beam.

  18. Hydrothermal synthesis, structure and photocatalytic properties of La/Bi co-doped NaTaO3

    International Nuclear Information System (INIS)

    Lan, Nguyen Thi; Huan, Bui Doan; Anh, Trinh Xuan; Chinh, Huynh Dang; Phan, Le Gia; Hoang, Luc Huy; Hong, Le Van

    2016-01-01

    La/Bi co-doped NaTaO 3 nanomaterials for photocatalytic applications have been successfully synthesized by hydrothermal method at low temperature. The obtained materials were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), energy dispersive spectroscopy (EDS) and UV-Vis molecular absorption spectroscopy. The results showed that the particle sizes of La/Bi co-doped NaTaO 3 were smaller than that of the pure NaTaO 3 . La/Bi co-doping has extended optical absorption in the visible light region and then successfully increased photocatalytic activity of the La/Bi-codoped NaTaO 3 that were evaluated by degradation of methylene blue (MB). (author)

  19. Fabrication of electrocatalytic Ta nanoparticles by reactive sputtering and ion soft landing

    Energy Technology Data Exchange (ETDEWEB)

    Johnson, Grant E.; Moser, Trevor; Engelhard, Mark; Browning, Nigel D.; Laskin, Julia

    2016-11-07

    About 40 years ago, it was shown that tungsten carbide exhibits similar catalytic behavior to Pt for certain commercially relevant reactions, thereby suggesting the possibility of cheaper and earth-abundant substitutes for costly and rare precious metal catalysts. In this work, reactive magnetron sputtering of Ta in the presence of three model hydrocarbons (2-butanol, heptane, and m-xylene) combined with gas aggregation and ion soft landing was employed to prepare organic-inorganic hybrid nanoparticles (NPs) on surfaces for evaluation of catalytic activity and durability. The electro-catalytic behavior of the NPs supported on glassy carbon was evaluated in acidic aqueous solution by cyclic voltammetry. The Ta-heptane and Ta-xylene NPs were revealed to be active and robust toward promotion of the oxygen reduction reaction, an important process occurring at the cathode in fuel cells. In comparison, pure Ta and Ta-butanol NPs were essentially unreactive. Characterization techniques including atomic force microscopy (AFM), X-ray photoelectron spectroscopy (XPS), and transmission electron microscopy (TEM) were applied to probe how different sputtering conditions such as the flow rates of gases, sputtering current, and aggregation length affect the properties of the NPs. AFM images reveal the focused size of the NPs as well as their preferential binding along the step edges of graphite surfaces. In comparison, TEM images of the same NPs on carbon grids show that they bind randomly to the surface with some agglomeration but little coalescence. The TEM images also reveal morphologies with crystalline cores surrounded by amorphous regions for NPs formed in the presence of 2-butanol and heptane. In contrast, NPs formed in the presence of m-xylene are amorphous throughout. XPS spectra indicate that while the percentage of Ta, C, and O in the NPs varies depending on the sputtering conditions and hydrocarbon employed, the electron binding energies of the elements are similar

  20. Functional characterization of a wheat NHX antiporter gene TaNHX2 that encodes a K(+/H(+ exchanger.

    Directory of Open Access Journals (Sweden)

    Yuanyuan Xu

    Full Text Available The subcellular localization of a wheat NHX antiporter, TaNHX2, was studied in Arabidopsis protoplasts, and its function was evaluated using Saccharomyces cerevisiae as a heterologous expression system. Fluorescence patterns of TaNHX2-GFP fusion protein in Arabidopsis cells indicated that TaNHX2 localized at endomembranes. TaNHX2 has significant sequence homology to NHX sodium exchangers from Arabidopsis, is abundant in roots and leaves and is induced by salt or dehydration treatments. Western blot analysis showed that TaNHX2 could be expressed in transgenic yeast cells. Expressed TaNHX2 protein suppressed the salt sensitivity of a yeast mutant strain by increasing its K(+ content when exposed to salt stress. TaNHX2 also increased the tolerance of the strain to potassium stress. However, the expression of TaNHX2 did not affect the sodium concentration in transgenic cells. Western blot analysis for tonoplast proteins indicated that the TaNHX2 protein localized at the tonoplast of transgenic yeast cells. The tonoplast vesicles from transgenic yeast cells displayed enhanced K(+/H(+ exchange activity but very little Na(+/H(+ exchange compared with controls transformed with the empty vector; Na(+/H(+ exchange was not detected with concentrations of less than 37.5 mM Na(+ in the reaction medium. Our data suggest that TaNHX2 is a endomembrane-bound protein and may primarily function as a K(+/H(+ antiporter, which is involved in cellular pH regulation and potassium nutrition under normal conditions. Under saline conditions, the protein mediates resistance to salt stress through the intracellular compartmentalization of potassium to regulate cellular pH and K(+ homeostasis.

  1. Correlation between thermodynamic and mechanical properties in Ta-W

    Energy Technology Data Exchange (ETDEWEB)

    Hoppe, Sandra; Mueller, Stefan [Institute of Advanced Ceramics, Hamburg University of Technology, Hamburg (Germany)

    2015-07-01

    Varying an alloy's concentration or alloying constituents strongly influences its structural and mechanical properties. Modern simulation methods like density functional theory in combination with the cluster expansion make the whole configurational space accessible. This way, also metastable structures may be considered, which are experimentally difficult to obtain. Recent results for several face-centered cubic (fcc) binary metal alloys suggest a linear correlation between thermodynamic stability and elastic properties at a fixed stoichiometry. This study aims to investigate the generality of these findings by considering a similar correlation for binary body-centered cubic (bcc) alloys. As a model system, Ta-W was chosen due to its simple phase diagram with solid solution in the whole concentration range. Interestingly, the elastic constants c{sub 44} and c{sub 12} show an opposing trend to that observed for fcc alloys: Energetically favorable structures are mechanically weaker than those further away from the ground-state line. This phenomenon may be related to the anomalous behavior of c{sub 44} with increasing pressure or temperature, which has been reported in the literature for Ta-W. We will discuss the interesting behavior of Ta-W with regard to its electronic structure.

  2. Erosion behavior of W-Ta coatings in plasmas of stationary mirror penning discharges

    International Nuclear Information System (INIS)

    Belous, V.A.; Bondarenko, M.N.; Glazunov, G.P.; Ilchenko, A.V.; Kuprin, A.S.; Konotopskiy, A.L.; Lunyov, V.M.; Ovcharenko, V.D.

    2016-01-01

    Investigations had been carried out of the influence of Ta alloying (2...16 wt.%) in W-coatings on their erosion behavior in steady state plasmas of Penning discharges in different gases: argon, nitrogen, and hydrogen. The coatings were deposited on stainless steel substrates by argon ion sputtering of targets made from appropriate metals. For comparison the erosion behavior had been examined of pure W and Ta coatings obtained by the same method. It was shown the essential decrease of an erosion rate after Ta addition in W coatings. The possible physical mechanism is suggested to explain such erosion behavior

  3. Shock Hugoniot measurements on Ta to 0.78 TPa

    International Nuclear Information System (INIS)

    Froeschner, K.E.; Lee, R.S.; Chau, H.H.; Weingart, R.C.

    1983-01-01

    Symmetric impact shock Hugoniot measurements have been made on Ta with an electrically exploded foil gun system. The results obtained to date for the Hugoniot of Ta cover the range 0.19 to 0.78 TPa (impact velocities from 4.0 to 9.7 km/s) and agree with data obtained by other researchers to within 2.7% rms. Recent improvements in the system include electromagnetic shielding of impactor and target, continuous measurement of impactor velocity with a Fabry-Perot interferometer and computer-aided analysis of shot film. Conservative extrapolation from current operating conditions indicate that pressures of 1.1 to 1.5 TPa could be achieved with little difficulty

  4. Highly dispersed TaOx nanoparticles prepared by electrodeposition as oxygen reduction electrocatalysts for polymer electrolyte fuel cells

    KAUST Repository

    Seo, Jeongsuk; Zhao, Lan; Cha, Dong Kyu; Takanabe, Kazuhiro; Katayama, Masao; Kubota, Jun; Domen, Kazunari

    2013-01-01

    for the oxygen reduction reaction (ORR) in polymer electrolyte fuel cells (PEFCs). Electrodeposition conditions of Ta complexes and subsequent various heat treatments for the deposited TaOx were examined for the best performance of the ORR. TaOx particles

  5. Critical role of the semiconductor-electrolyte interface in photocatalytic performance for water-splitting reactions using Ta3N5 particles

    KAUST Repository

    Nurlaela, Ela

    2014-08-26

    Distinct photocatalytic performance was observed when Ta3N 5 was synthesized from commercially available Ta2O 5 or from Ta2O5 prepared from TaCl5 via the sol-gel route. With respect to photocatalytic O2 evolution with Ag+ as a sacrificial reagent, the Ta3N5 produced from commercial Ta2O5 exhibited higher activity than the Ta3N5 produced via the sol-gel route. When the Ta3N5 photocatalysts were decorated with Pt nanoparticles in a similar manner, the Ta3N5 from the sol-gel route exhibited higher photocatalytic hydrogen evolution activity from a 10% aqueous methanol solution than Ta3N5 prepared from commercial Ta2O5 where no hydrogen can be detected. Detailed surface and bulk characterizations were conducted to obtain fundamental insight into the resulting photocatalytic activities. The characterization techniques, including XRD, elemental analysis, Raman spectroscopy, UV-vis spectroscopy, and surface-area measurements, revealed only negligible differences between these two photocatalysts. Our thorough characterization of the surface properties demonstrated that the very thin outermost layer of Ta3N5, with a thickness of a few nanometers, consists of either the reduced state of tantalum (TaN) or an amorphous phase. The extent of this surface layer was likely dependent on the nature of precursor oxide surfaces. DFT calculations based on partially oxidized Ta3N4.83O0.17 and N deficient Ta3N4.83 consisting of reduced Ta species well described the optoelectrochemical properties obtained from the experiments. Electrochemical and Mott-Schottky analyses demonstrated that the surface layer drastically affects the energetic picture at the semiconductor-electrolyte interface, which can consequently affect the photocatalytic performance. Chemical etching of the surface of Ta3N5 particles to remove this surface layer unites the photocatalytic properties with the photocatalytic performance of these two materials. Mott-Schottky plots of these chemically etched Ta3N5 materials

  6. Equivalence analysis of quality traits in transgenic soybean over-expressing TaDREB3%转TaDREB3基因大豆的品质等同性分析

    Institute of Scientific and Technical Information of China (English)

    张彬彬; 李文滨

    2011-01-01

    Glydne max cv Dongnong 50 was transformed with a stress - tolerance gene TaDREBi. Three trans-genic lines with stable heredity were obtained and the seeds of the T4 generation were sown in field. The contents of protein, oil, fatty acid and isoflavone in seeds of the three transgenic lines and the non - transgenic control lines were determined and compared. The object was to study whether the introduction of foreign gene TaDREBi had changed the quality traits of soybean. Results showed that there were no significant differences in protein contents, oil contents, as well as fatty acid contents in soybean seeds between three transgenic lines and the control plants. Between the transgenic line 1 and the control, daidzein contents showed significant difference, but isoflavone contents showed no significant difference. It was suggested that introduction of TaDREBi into soybean did not cause much change in quality traits.%将抗逆基因TaDREB3转入大豆品种东农50,得到3个稳定遗传的株系,并将T4株系种子播于大田中.对3个转TaDREB3基因株系及非转基因对照株系的种子分别进行蛋白质、油份、脂肪酸、异黄酮等品质性状的等同性分析,研究转化外源基因TaDREB3后大豆原有品质性状是否有改变.结果表明:3个转基因株系和对照植株相比,蛋白质含量、油分含量和脂肪酸含量均差异不显著;转基因株系1的大豆黄素虽然和对照差异显著,但是异黄酮总含量和对照没有显著性差异.说明TaDREB3基因的导人并没有改变大豆的品质性状.

  7. Post-Mission Assessment for Tactical Training-Trends Analysis (PMATT-TA): Usability Analysis Report

    Science.gov (United States)

    2014-07-01

    information, PMATT-TA also supports data calls to understand fleet readiness and proficiency. Additionally, PMATT-TA addresses a need for a digitally based...Software Quality Journal, 4(2), 115-130. Gray, W. D., & Salzman, M. C. (1998). Damaged merchandise ? A review of experiments that compare usability

  8. Long periodicity of Blazar with RXTE ASM, TA and HEGRA

    OpenAIRE

    Osone, S.; Teshima, M.

    2002-01-01

    Long periodicity for Mkn501 during a large flare in 1997 have been reported by TA, HEGRA group. Here, we establish this periodicity with archival data of RXTE All Sky Monitor(ASM), Telescope Array(TA) and HEGRA with a chance probability less than $10^{-5}$. We also find that an origin of 23 day periodicity is related with a change of either a gamma factor of electrons $\\gamma$ or the magnetic field or a beaming factor. And, in order to search for a category which have a long periodicity, we m...

  9. Transparent conductive Ta2O5-codoped ITO thin films prepared by different heating process

    International Nuclear Information System (INIS)

    Zhang, B.; Dong, X.P.; Wu, J.S.; Xu, X.F.

    2008-01-01

    Tantalum-doped indium tin oxide thin films were deposited by a cosputtering technique with an ITO target and a Ta 2 O 5 target. The variations of microstructure, electrical and optical properties with substrate temperature and annealing temperature were investigated in some detail. Ta-doped ITO thin films showed better crystalline structure with different prominent plane orientation by different heating process. ITO:Ta thin films deposited at room temperature showed better optical and electrical properties. Increasing substrate temperature and reasonable annealing temperature could remarkably improve the optical and electrical properties of the films. The variation of carrier concentration had an important influence on near-IR reflection, near-UV absorption and optical bandgap. ITO:Ta thin films showed wider optical bandgap. ITO:Ta thin films under the optimum parameters had a sheet resistance of 10-20 and ohm;/sq and a transmittance of 85% with an optical bandgap of above 4.0 eV. (copyright 2008 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim) (orig.)

  10. The preferential orientation and lattice misfit of the directionally solidified Fe-Al-Ta eutectic composite

    Science.gov (United States)

    Cui, Chunjuan; Wang, Pei; Yang, Meng; Wen, Yagang; Ren, Chiqiang; Wang, Songyuan

    2018-01-01

    Fe-Al intermetallic compound has been paid more attentions recently in many fields such as aeronautic, aerospace, automobile, energy and chemical engineering, and so on. In this paper Fe-Al-Ta eutectic was prepared by a modified Bridgman directional solidification technique, and it is found that microstructure of the Fe-Al-Ta eutectic alloy transforms from the broken-lamellar eutectic to cellular eutectic with the increase of the solidification rate. In the cellular eutectic structure, the fibers are parallel to each other within the same grain, but some fibers are deviated from the original orientation at the grain boundaries. To study the crystallographic orientation relationship (OR) between the two phases, the preferential orientation of the Fe-Al-Ta eutectic alloy at the different solidification rates was studied by Selected Area Electron Diffraction (SAED). Moreover, the lattice misfit between Fe2Ta(Al) Laves phase and Fe(Al,Ta) matrix phase was calculated.

  11. Mechanical properties and biocompatibility in alloy Ti-Ta system containing oxygen; Propriedades mecanicas e biocompatibilidades em ligas do sistema Ti-Ta contendo oxigenio

    Energy Technology Data Exchange (ETDEWEB)

    Ruiz, S.L.M.; Grandini, C.R., E-mail: samlea@fc.unesp.b [Universidade Estadual Paulista (UNESP), Bauru, SP (Brazil). Lab. de Anelasticidade e Biomateriais; Claro, A.P.R.A. [Universidade Estadual Paulista Julio de Mesquisa Filho (DMT/UNESP), Guaratingueta, SP (Brazil). Fac. de Engenharia. Dept. de Materiais e Tecnologia

    2010-07-01

    Due to the excellent properties such as corrosion resistance, good mechanical strength/density, good performance at high temperatures, Ti is very useful in the chemical industry and aerospace. Currently, their use has expanded to the field of biomaterials, due to its excellent biocompatibility and reduced elasticity modulus, favouring the production of orthopaedic and dental prostheses. Promising alloys are the Ti-Ta system and researches have been directed to describe and understand the behavior of this system. In this paper, samples of Ti-Ta alloys containing 8 and 16% (wt%) containing interstitial oxygen were prepared and characterized by density, xray diffraction, hardness, elasticity modulus measurements and in vitro cytotoxicity tests. (author)

  12. The Novel Wheat Transcription Factor TaNAC47 Enhances Multiple Abiotic Stress Tolerances in Transgenic Plants.

    Science.gov (United States)

    Zhang, Lina; Zhang, Lichao; Xia, Chuan; Zhao, Guangyao; Jia, Jizeng; Kong, Xiuying

    2015-01-01

    NAC transcription factors play diverse roles in plant development and responses to abiotic stresses. However, the biological roles of NAC family members in wheat are not well understood. Here, we reported the isolation and functional characterization of a novel wheat TaNAC47 gene. TaNAC47 encoded protein, localizing in the nucleus, is able to bind to the ABRE cis-element and transactivate transcription in yeast, suggesting that it likely functions as a transcriptional activator. We also showed that TaNAC47 is differentially expressed in different tissues, and its expression was induced by the stress treatments of salt, cold, polyethylene glycol and exogenous abscisic acid. Furthermore, overexpression of TaNAC47 in Arabidopsis resulted in ABA hypersensitivity and enhancing tolerance of transgenic plants to drought, salt, and freezing stresses. Strikingly, overexpression of TaNAC47 was found to activate the expression of downstream genes and change several physiological indices that may enable transgenic plants to overcome unfavorable environments. Taken together, these results uncovered an important role of wheat TaNAC47 gene in response to ABA and abiotic stresses.

  13. Influences of Pr and Ta doping concentration on the characteristic features of FTO thin film deposited by spray pyrolysis

    International Nuclear Information System (INIS)

    Turgut, Güven; Koçyiğit, Adem; Sönmez, Erdal

    2015-01-01

    The Pr and Ta separately doped FTO (10 at.% F incorporated SnO 2 ) films are fabricated via spray pyrolysis. The microstructural, topographic, optical, and electrical features of fluorine-doped TO (FTO) films are investigated as functions of Pr and Ta dopant concentrations. The x-ray diffraction (XRD) measurements reveal that all deposited films show polycrystalline tin oxide crystal property. FTO film has (200) preferential orientation, but this orientation changes to (211) direction with Pr and Ta doping ratio increasing. Atomic force microscopy (AFM) and scanning electron microscopy (SEM) analyses show that all films have uniform and homogenous nanoparticle distributions. Furthermore, morphologies of the films depend on the ratio between Pr and Ta dopants. From ultraviolet-visible (UV-Vis) spectrophotometer measurements, it is shown that the transmittance value of FTO film decreases with Pr and Ta doping elements increasing. The band gap value of FTO film increases only at 1 at.% Ta doping level, it drops off with Pr and Ta doping ratio increasing at other doped FTO films. The electrical measurements indicate that the sheet resistance value of FTO film initially decreases with Pr and Ta doping ratio decreasing and then it increases with Pr and Ta doping ratio increasing. The highest value of figure of merit is obtained for 1 at.% Ta- and Pr-doped FTO film. These results suggest that Pr- and Ta-doped FTO films may be appealing candidates for TCO applications. (paper)

  14. Mechanisms of Low-Temperature Nitridation Technology on a TaN Thin Film Resistor for Temperature Sensor Applications.

    Science.gov (United States)

    Chen, Huey-Ru; Chen, Ying-Chung; Chang, Ting-Chang; Chang, Kuan-Chang; Tsai, Tsung-Ming; Chu, Tian-Jian; Shih, Chih-Cheng; Chuang, Nai-Chuan; Wang, Kao-Yuan

    2016-12-01

    In this letter, we propose a novel low-temperature nitridation technology on a tantalum nitride (TaN) thin film resistor (TFR) through supercritical carbon dioxide (SCCO2) treatment for temperature sensor applications. We also found that the sensitivity of temperature of the TaN TFR was improved about 10.2 %, which can be demonstrated from measurement of temperature coefficient of resistance (TCR). In order to understand the mechanism of SCCO2 nitridation on the TaN TFR, the carrier conduction mechanism of the device was analyzed through current fitting. The current conduction mechanism of the TaN TFR changes from hopping to a Schottky emission after the low-temperature SCCO2 nitridation treatment. A model of vacancy passivation in TaN grains with nitrogen and by SCCO2 nitridation treatment is eventually proposed to increase the isolation ability in TaN TFR, which causes the transfer of current conduction mechanisms.

  15. Expression of TaWRKY44, a wheat WRKY gene, in transgenic tobacco confers multiple abiotic stress tolerances

    Directory of Open Access Journals (Sweden)

    Xiatian eWang

    2015-08-01

    Full Text Available The WRKY transcription factors have been reported to be involved in various plant physiological and biochemical processes. In this study, we successfully assembled ten unigenes from expressed sequence tags (ESTs of wheat and designated them as TaWRKY44–TaWRKY53, respectively. Among these genes, a subgroup I gene, TaWRKY44, was found to be upregulated by treatments with PEG6000, NaCl, 4°C, abscisic acid (ABA, H2O2 and gibberellin (GA. The TaWRKY44-GFP fusion protein was localized to the nucleus of onion epidermal cells, and TaWRKY44 was able to bind to the core DNA sequences of TTGACC and TTAACC in yeast. The N-terminal of TaWRKY44 showed transcriptional activation activity. Expression of TaWRKY44 in tobacco plants conferred drought and salt tolerance and transgenic tobacco exhibited a higher survival rate, relative water content (RWC, soluble sugar, proline and superoxide dismutase (SOD content, as well as higher activities of catalase (CAT and peroxidase (POD, but less ion leakage (IL, lower contents of malondialdehyde (MDA, and H2O2. In addition, expression of TaWRKY44 also increased the seed germination rate in the transgenic lines under osmotic stress conditions while exhibiting a lower H2O2 content and higher SOD, CAT and POD activities. Expression of TaWRKY44 upregulated the expression of some reactive oxygen species (ROS-related genes and stress-responsive genes in tobacco under osmotic stresses. These data demonstrate that TaWRKY44 may act as a positive regulator in drought/salt/osmotic stress responses by either efficient ROS elimination through direct or indirect activation of the cellular antioxidant systems or activation of stress-associated gene expression.

  16. Characteristics of (Ti,Ta)N thin films prepared by using pulsed high energy density plasma

    Energy Technology Data Exchange (ETDEWEB)

    Feng Wenran [Beijing National Laboratory for Condensed Matter Physics, Institute of Physics, Chinese Academy of Sciences, Beijing 100080 (China); Chen Guangliang [Beijing National Laboratory for Condensed Matter Physics, Institute of Physics, Chinese Academy of Sciences, Beijing 100080 (China); Li Li [Beijing National Laboratory for Condensed Matter Physics, Institute of Physics, Chinese Academy of Sciences, Beijing 100080 (China); Lv Guohua [Beijing National Laboratory for Condensed Matter Physics, Institute of Physics, Chinese Academy of Sciences, Beijing 100080 (China); Zhang Xianhui [College of Science, Changchun University of Science and Technology, Changchun 130022, Jilin Province (China); Niu Erwu [Beijing National Laboratory for Condensed Matter Physics, Institute of Physics, Chinese Academy of Sciences, Beijing 100080 (China); Liu Chizi [Beijing National Laboratory for Condensed Matter Physics, Institute of Physics, Chinese Academy of Sciences, Beijing 100080 (China); Yang Size [Beijing National Laboratory for Condensed Matter Physics, Institute of Physics, Chinese Academy of Sciences, Beijing 100080 (China)

    2007-07-21

    (Ti,Ta)N films were prepared by pulsed high energy density plasma (PHEDP) from a coaxial gun in N{sub 2} gas. The coaxial gun is composed of a tantalum inner electrode and a titanium outer one. Material characteristics of the (Ti,Ta)N film were investigated by x-ray photoelectron spectroscopy and x-ray diffraction. The microstructure of the film was observed by a scanning electron microscope. The elemental composition and the interface of the film/substrate were analysed using Auger electron spectrometry. Our results suggest that the binary metal nitride film (Ti,Ta)N, can be prepared by PHEDP. It also shows that dense nanocrystalline (Ti,Ta)N film can be achieved.

  17. Accident selection methodology for TA-55 FSAR

    International Nuclear Information System (INIS)

    Letellier, B.C.; Pan, P.Y.; Sasser, M.K.

    1995-01-01

    In the past, the selection of representative accidents for refined analysis from the numerous scenarios identified in hazards analyses (HAs) has involved significant judgment and has been difficult to defend. As part of upgrading the Final Safety Analysis Report (FSAR) for the TA-55 plutonium facility at the Los Alamos National Laboratory, an accident selection process was developed that is mostly mechanical and reproducible in nature and fulfills the requirements of the Department of Energy (DOE) Standard 3009 and DOE Order 5480.23. Among the objectives specified by this guidance are the requirements that accident screening (1) consider accidents during normal and abnormal operating conditions, (2) consider both design basis and beyond design basis accidents, (3) characterize accidents by category (operational, natural phenomena, etc.) and by type (spill, explosion, fire, etc.), and (4) identify accidents that bound all foreseeable accident types. The accident selection process described here in the context of the TA-55 FSAR is applicable to all types of DOE facilities

  18. Ion-beam mixing and thermal annealing of Al--Nb and Al--Ta thin films

    International Nuclear Information System (INIS)

    Rai, A.K.; Bhattacharya, R.S.; Mendiratta, M.G.; Subramanian, P.R.; Dimiduk, D.M.

    1988-01-01

    Ion-beam mixing and thermal annealing of thin, alternating layers of Al and Nb, as well as Al and Ta, were investigated by selected area diffraction and Rutherford backscattering. The individual layer thicknesses were adjusted to obtain the overall compositions as Al 3 Nb and Al 3 Ta. The films were ion mixed with 1 MeV Au + ions at a dose of 1 x 10 16 ions cm/sup -2/ . Uniform mixing and amorphization were achieved for both Al--Nb and Al--Ta systems. Equilibrium crystalline Al 3 Nb and Al 3 Ta phases were formed after annealing of ion mixed amorphous films at 400 0 C for 6 h. Unmixed films, however, remained unreacted at 400 0 C for 1 h. Partial reaction was observed in the unmixed film of Al--Nb at 400 0 C for 6 h. After annealing at 500 0 C for 1 h, a complete reaction and formation of Al 3 Nb and Al 3 Ta phases in the respective films were observed. The influence of thermodynamics on the phase formation by ion mixing and thermal annealing is discussed

  19. ANALISIS TINGKAT KESEHATAN KOPERASI SIMPAN PINJAM BALO’TA CABANG POLEWALI MANDAR

    Directory of Open Access Journals (Sweden)

    Sri Febrianti

    2017-08-01

    Full Text Available July 2017. SRI FEBRIANTI, NPM: 4513012028 with the title thesis "Analysis Of The Health Levels Of Balo’Ta Branch Of Polewali Mandar Savings And Loan Cooperative". (Guided by Dr. H. Muh. Yusuf Saleh,SE.,M.Si as mentors I dan  H. Muh Idris.,SE.,M.Si as mentors II This study aims to investigate the health levels of Balo’Ta branch of Polewali Mandar Savings and Loan Cooperative in 2015-2016 based on the Regulations of the Minister of Cooperative and Small- and Medium-scale Businesses of the Republic of Indonesia No. 14/Per/M.KUKM/XII/2009 regarding the aspects of capital, productive asset quality, management, liquidity, efficiency, autonomy and growth, and cooperative identity. The results of the study in 2015-2016 Health Levels Of Balo’Ta Branch Of Polewali Mandar Savings And Loan Cooperative which was in the moderately healthy category

  20. Level structures in odd-odd deformed nucleus {sup 184}Ta

    Energy Technology Data Exchange (ETDEWEB)

    Gowrishankar, R.; Sood, P.C. [Sri Sathya Sai Institute of Higher Learning, Department of Physics, Prasanthinilayam (India)

    2016-02-15

    A detailed low-energy level scheme of the odd-odd n-rich nucleus {sub 73}{sup 184}Ta{sub 111} is constructed using the well tested Two-Quasiparticle Rotor Model (TQRM) for calculating the bandhead energies of physically admissible 2qp configurations with the inclusion of residual n-p interaction contribution. The presently available data on this level scheme from {sup 184}Hf decay are shown to be in agreement with these calculations. Our analysis concludes that {sup 184}Hf (Q{sub β} = 1340(30) keV) decay admits of 7 additional (to the 3 presently reported) β -branches to {sup 184}Ta with J = 0 or 1 and 8 more physically admissible weak (1f{sup u}) β -branches populating J{sup π} = 2{sup -} levels in {sup 184}Ta. Further, a close examination of our level scheme clearly indicates the existence of a low-lying (E{sub x} = 260(40) keV) high-spin (J{sup π} = 10{sup -}) long-lived isomer in this nucleus. (orig.)

  1. Pressure-induced amorphization of La1/3TaO3

    International Nuclear Information System (INIS)

    Noked, O.; Melchior, A.; Shuker, R.; Livneh, T.; Steininger, R.; Kennedy, B.J.; Sterer, E.

    2013-01-01

    La 1/3 TaO 3 , an A-site cation deficient perovskite, has been studied under pressure by synchrotron X-ray powder diffraction and Raman spectroscopy. It undergoes irreversible pressure induced amorphization at P=18.5 GPa. An almost linear unit cell volume decrease vs. pressure is observed from ambient pressure up to the phase transition. The Raman spectroscopy also shows amorphization at the same pressure, with positive shifts of all modes as a function of pressure. The pressure dependence of the E g and A 1g Raman modes arising from the octahedral oxygen network is discussed. - Graphical abstract: La 1/3 Tao 3 exhibits linear pressure–volume relation until irreversible pressure induced amorphization at 18.5 Gpa. - Highlights: • La 1/3 TaO 3 has been studied under pressure by synchrotron XRD and Raman spectroscopy. • La 1/3 TaO 3 undergoes irreversible pressure induced amorphization around 18.5 GPa. • The transition is manifested in both XRD and Raman measurements. • A linear P–V relation is observed from ambient pressure up to the phase transition

  2. TA 55 Reinvestment Project II Phase C Update Project Status May 23, 2017

    Energy Technology Data Exchange (ETDEWEB)

    Giordano, Anthony P. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

    2017-05-25

    The TA-55 Reinvestment Project (TRP) II Phase C is a critical infrastructure project focused on improving safety and reliability of the Los Alamos National Laboratory (LANL) TA-55 Complex. The Project recapitalizes and revitalizes aging and obsolete facility and safety systems providing a sustainable nuclear facility for National Security Missions.

  3. TaDb: A time-aware diffusion-based recommender algorithm

    Science.gov (United States)

    Li, Wen-Jun; Xu, Yuan-Yuan; Dong, Qiang; Zhou, Jun-Lin; Fu, Yan

    2015-02-01

    Traditional recommender algorithms usually employ the early and recent records indiscriminately, which overlooks the change of user interests over time. In this paper, we show that the interests of a user remain stable in a short-term interval and drift during a long-term period. Based on this observation, we propose a time-aware diffusion-based (TaDb) recommender algorithm, which assigns different temporal weights to the leading links existing before the target user's collection and the following links appearing after that in the diffusion process. Experiments on four real datasets, Netflix, MovieLens, FriendFeed and Delicious show that TaDb algorithm significantly improves the prediction accuracy compared with the algorithms not considering temporal effects.

  4. Phonon and thermal properties of exfoliated TaSe2 thin films

    International Nuclear Information System (INIS)

    Yan, Z.; Jiang, C.; Renteria, J.; Pope, T. R.; Tsang, C. F.; Stickney, J. L.; Salguero, T. T.; Goli, P.; Balandin, A. A.

    2013-01-01

    We report on the phonon and thermal properties of thin films of tantalum diselenide (2H-TaSe 2 ) obtained via the “graphene-like” mechanical exfoliation of crystals grown by chemical vapor transport. The ratio of the intensities of the Raman peak from the Si substrate and the E 2g peak of TaSe 2 presents a convenient metric for quantifying film thickness. The temperature coefficients for two main Raman peaks, A 1g and E 2g , are −0.013 and −0.0097 cm −1 / o C, respectively. The Raman optothermal measurements indicate that the room temperature thermal conductivity in these films decreases from its bulk value of ∼16 W/mK to ∼9 W/mK in 45-nm thick films. The measurement of electrical resistivity of the field-effect devices with TaSe 2 channels shows that heat conduction is dominated by acoustic phonons in these van der Waals films. The scaling of thermal conductivity with the film thickness suggests that the phonon scattering from the film boundaries is substantial despite the sharp interfaces of the mechanically cleaved samples. These results are important for understanding the thermal properties of thin films exfoliated from TaSe 2 and other metal dichalcogenides, as well as for evaluating self-heating effects in devices made from such materials

  5. Phonon and thermal properties of exfoliated TaSe2 thin films

    Science.gov (United States)

    Yan, Z.; Jiang, C.; Pope, T. R.; Tsang, C. F.; Stickney, J. L.; Goli, P.; Renteria, J.; Salguero, T. T.; Balandin, A. A.

    2013-11-01

    We report on the phonon and thermal properties of thin films of tantalum diselenide (2H-TaSe2) obtained via the "graphene-like" mechanical exfoliation of crystals grown by chemical vapor transport. The ratio of the intensities of the Raman peak from the Si substrate and the E2g peak of TaSe2 presents a convenient metric for quantifying film thickness. The temperature coefficients for two main Raman peaks, A1g and E2g, are -0.013 and -0.0097 cm-1/oC, respectively. The Raman optothermal measurements indicate that the room temperature thermal conductivity in these films decreases from its bulk value of ˜16 W/mK to ˜9 W/mK in 45-nm thick films. The measurement of electrical resistivity of the field-effect devices with TaSe2 channels shows that heat conduction is dominated by acoustic phonons in these van der Waals films. The scaling of thermal conductivity with the film thickness suggests that the phonon scattering from the film boundaries is substantial despite the sharp interfaces of the mechanically cleaved samples. These results are important for understanding the thermal properties of thin films exfoliated from TaSe2 and other metal dichalcogenides, as well as for evaluating self-heating effects in devices made from such materials.

  6. Flux-mediated syntheses, structural characterization and low-temperature polymorphism of the p-type semiconductor Cu2Ta4O11

    Science.gov (United States)

    King, Nacole; Sullivan, Ian; Watkins-Curry, Pilanda; Chan, Julia Y.; Maggard, Paul A.

    2016-04-01

    A new low-temperature polymorph of the copper(I)-tantalate, α-Cu2Ta4O11, has been synthesized in a molten CuCl-flux reaction at 665 °C for 1 h and characterized by powder X-ray diffraction Rietveld refinements (space group Cc (#9), a=10.734(1) Å, b = 6.2506(3) Å, c=12.887(1) Å, β = 106.070(4)°). The α-Cu2Ta4O11 phase is a lower-symmetry monoclinic polymorph of the rhombohedral Cu2Ta4O11 structure (i.e., β-Cu2Ta4O11 space group R 3 ̅ c (#167), a = 6.2190(2) Å, c=37.107(1) Å), and related crystallographically by ahex=amono/√3, bhex=bmono, and chex=3cmonosinβmono. Its structure is similar to the rhombohedral β-Cu2Ta4O11 and is composed of single layers of highly-distorted and edge-shared TaO7 and TaO6 polyhedra alternating with layers of nearly linearly-coordinated Cu(I) cations and isolated TaO6 octahedra. Temperature dependent powder X-ray diffraction data show the α-Cu2Ta4O11 phase is relatively stable under vacuum at 223 K and 298 K, but reversibly transforms to β-Cu2Ta4O11 by at least 523 K and higher temperatures. The symmetry-lowering distortions from β-Cu2Ta4O11 to α-Cu2Ta4O11 arise from the out-of-center displacements of the Ta 5d0 cations in the TaO7 pentagonal bipyramids. The UV-vis diffuse reflectance spectrum of the monoclinic α-Cu2Ta4O11 shows an indirect bandgap transition of ∼2.6 eV, with the higher-energy direct transitions starting at ∼2.7 eV. Photoelectrochemical measurements on polycrystalline films of α-Cu2Ta4O11 show strong cathodic photocurrents of ∼1.5 mA/cm2 under AM 1.5 G solar irradiation.

  7. Functional Analysis and Marker Development of TaCRT-D Gene in Common Wheat (Triticum aestivum L.

    Directory of Open Access Journals (Sweden)

    Jiping Wang

    2017-09-01

    Full Text Available Calreticulin (CRT, an endoplasmic reticulum (ER-localized Ca2+-binding/buffering protein, is highly conserved and extensively expressed in animal and plant cells. To understand the function of CRTs in wheat (Triticum aestivum L., particularly their roles in stress tolerance, we cloned the full-length genomic sequence of the TaCRT-D isoform from D genome of common hexaploid wheat, and characterized its function by transgenic Arabidopsis system. TaCRT-D exhibited different expression patterns in wheat seedling under different abiotic stresses. Transgenic Arabidopsis plants overexpressing ORF of TaCRT-D displayed more tolerance to drought, cold, salt, mannitol, and other abiotic stresses at both seed germination and seedling stages, compared with the wild-type controls. Furthermore, DNA polymorphism analysis and gene mapping were employed to develop the functional markers of this gene for marker-assistant selection in wheat breeding program. One SNP, S440 (T→C was detected at the TaCRT-D locus by genotyping a wheat recombinant inbred line (RIL population (114 lines developed from Opata 85 × W7984. The TaCRT-D was then fine mapped between markers Xgwm645 and Xgwm664 on chromosome 3DL, corresponding to genetic distances of 3.5 and 4.4 cM, respectively, using the RIL population and Chinese Spring nulli-tetrasomic lines. Finally, the genome-specific and allele-specific markers were developed for the TaCRT-D gene. These findings indicate that TaCRT-D function importantly in plant stress responses, providing a gene target for genetic engineering to increase plant stress tolerance and the functional markers of TaCRT-D for marker-assistant selection in wheat breeding.

  8. Functional Analysis and Marker Development of TaCRT-D Gene in Common Wheat (Triticum aestivum L.).

    Science.gov (United States)

    Wang, Jiping; Li, Runzhi; Mao, Xinguo; Jing, Ruilian

    2017-01-01

    Calreticulin (CRT), an endoplasmic reticulum (ER)-localized Ca 2+ -binding/buffering protein, is highly conserved and extensively expressed in animal and plant cells. To understand the function of CRTs in wheat ( Triticum aestivum L.), particularly their roles in stress tolerance, we cloned the full-length genomic sequence of the TaCRT-D isoform from D genome of common hexaploid wheat, and characterized its function by transgenic Arabidopsis system. TaCRT-D exhibited different expression patterns in wheat seedling under different abiotic stresses. Transgenic Arabidopsis plants overexpressing ORF of TaCRT-D displayed more tolerance to drought, cold, salt, mannitol, and other abiotic stresses at both seed germination and seedling stages, compared with the wild-type controls. Furthermore, DNA polymorphism analysis and gene mapping were employed to develop the functional markers of this gene for marker-assistant selection in wheat breeding program. One SNP, S440 (T→C) was detected at the TaCRT-D locus by genotyping a wheat recombinant inbred line (RIL) population (114 lines) developed from Opata 85 × W7984. The TaCRT-D was then fine mapped between markers Xgwm645 and Xgwm664 on chromosome 3DL, corresponding to genetic distances of 3.5 and 4.4 cM, respectively, using the RIL population and Chinese Spring nulli-tetrasomic lines. Finally, the genome-specific and allele-specific markers were developed for the TaCRT-D gene. These findings indicate that TaCRT-D function importantly in plant stress responses, providing a gene target for genetic engineering to increase plant stress tolerance and the functional markers of TaCRT-D for marker-assistant selection in wheat breeding.

  9. Thermal, optical, and dielectric properties of fluoride Rb2TaF7

    Science.gov (United States)

    Pogorel'tsev, E. I.; Mel'nikova, S. V.; Kartashev, A. V.; Gorev, M. V.; Flerov, I. N.; Laptash, N. M.

    2017-05-01

    The thermal, optical, and dielectric properties of fluoride Rb2TaF7 were investigated. It was observed that the variation in chemical pressure in fluorides A 2 +TaF7 caused by the cation substitution of rubidium for ammonium does not affect the ferroelastic nature of structural distortions, but leads to stabilization of the high- and low-temperature phases and enhancement of birefringence. The entropy of the phase transition P4/nmm ↔ Cmma is typical of the shift transformations, which is consistent with a model of the initial and distorted phase structures. The anisotropy of chemical pressure causes the change of signs of the anomalous strain and baric coefficient dT/ dp of Rb2TaF7 as compared with the values for its ammonium analog.

  10. NbTaV-(Ti,W) refractory high-entropy alloys: Experiments and modeling

    Energy Technology Data Exchange (ETDEWEB)

    Yao, H.W. [Laboratory of Applied Physics and Mechanics of Advanced Materials, College of Materials Science and Engineering, Taiyuan University of Technology, Taiyuan 030024 (China); Qiao, J.W., E-mail: qiaojunwei@gmail.com [Laboratory of Applied Physics and Mechanics of Advanced Materials, College of Materials Science and Engineering, Taiyuan University of Technology, Taiyuan 030024 (China); Gao, M.C., E-mail: michael.gao@netl.doe.gov [National Energy Technology Laboratory, 1450 Queen Ave SW, Albany, OR 97321 (United States); AECOM, P.O. Box 1959, Albany, OR 97321 (United States); Hawk, J.A. [National Energy Technology Laboratory, 1450 Queen Ave SW, Albany, OR 97321 (United States); Ma, S.G. [Institute of Applied Mechanics and Biomedical Engineering, Taiyuan University of Technology, Taiyuan 030024 (China); Zhou, H.F. [Laboratory of Applied Physics and Mechanics of Advanced Materials, College of Materials Science and Engineering, Taiyuan University of Technology, Taiyuan 030024 (China); Zhang, Y. [State Key Laboratory for Advanced Metals and Materials, University of Science and Technology Beijing, Beijing 100083 (China)

    2016-09-30

    This study reports the design and development of ductile and strong refractory single-phase high-entropy alloys (HEAs) for high temperature applications, based on NbTaV with addition of Ti and W. Assisted by CALPHAD modeling, a single body-centered cubic solid solution phase was experimentally confirmed in the as-cast ingots using X-ray diffraction and scanning electron microscopy. The observed elemental segregation in each alloy qualitatively agrees with CALPHAD prediction. The Vickers microhardnesses (and yield strengths) of the alloys are about 3 (and 3.5–4.4) times that those estimated from the rule of mixture. While NbTaTiVW shows an impressive yield strength of 1420 MPa with fracture strain of 20%, NbTaTiV exhibits exceptional compressive ductility at room temperature.

  11. Double Dirac point semimetal in 2D material: Ta2Se3

    Science.gov (United States)

    Ma, Yandong; Jing, Yu; Heine, Thomas

    2017-06-01

    Here, we report by first-principles calculations one new stable 2D Dirac material, Ta2Se3 monolayer. For this system, stable layered bulk phase exists, and exfoliation should be possible. Ta2Se3 monolayer is demonstrated to support two Dirac points close to the Fermi level, achieving the exotic 2D double Dirac semimetal. And like 2D single Dirac and 2D node-line semimetals, spin-orbit coupling could introduce an insulating state in this new class of 2D Dirac semimetals. Moreover, the Dirac feature in this system is layer-dependent and a metal-to-insulator transition is identified in Ta2Se3 when reducing the layer-thickness from bilayer to monolayer. These findings are of fundamental interests and of great importance for nanoscale device applications.

  12. The novel wheat transcription factor TaNAC47 enhances multiple abiotic stress tolerances in transgenic plants

    Directory of Open Access Journals (Sweden)

    Li Na eZhang

    2016-01-01

    Full Text Available NAC transcription factors play diverse roles in plant development and responses to abiotic stresses. However, the biological roles of NAC family members in wheat are not well understood. Here, we reported the isolation and functional characterization of a novel wheat TaNAC47 gene. TaNAC47 encoded protein, localizing in the nucleus, is able to bind to the ABRE cis-element and transactivate transcription in yeast, suggesting that it likely functions as a transcriptional activator. We also showed that TaNAC47 is differentially expressed in different tissues, and its expression was induced by the stress treatments of salt, cold, polyethylene glycol (PEG and exogenous abscisic acid (ABA. Furthermore, overexpression of TaNAC47 in Arabidopsis resulted in ABA hypersensitivity and enhancing tolerance of transgenic plants to drought, salt and freezing stresses. Strikingly, overexpression of TaNAC47 was found to activate the expression of downstream genes and change several physiological indices that may enable transgenic plants to overcome unfavorable environments. Taken together, these results uncovered an important role of wheat TaNAC47 gene in response to ABA and abiotic stresses.

  13. Enhanced photoactivity from single-crystalline SrTaO{sub 2}N nanoplates synthesized by topotactic nitridation

    Energy Technology Data Exchange (ETDEWEB)

    Fu, Jie; Skrabalak, Sara E. [Department of Chemistry, Indiana University, Bloomington, IN (United States)

    2017-11-06

    There are few methods yielding oxynitride crystals with defined shape, yet shape-controlled crystals often give enhanced photoactivity. Herein, single-crystalline SrTaO{sub 2}N nanoplates and polyhedra are achieved selectively. Central to these synthetic advances is the crystallization pathways used, in which single-crystalline SrTaO{sub 2}N nanoplates form by topotactic nitridation of aerosol-prepared Sr{sub 2}Ta{sub 2}O{sub 7} nanoplates and SrTaO{sub 2}N polyhedra form by flux-assisted nitridation of the nanoplates. Evaluation of these materials for the oxygen evolution reaction (OER) and hydrogen evolution reaction (HER) showed improved performance for the SrTaO{sub 2}N nanoplates, with a record apparent quantum efficiency (AQE) of 6.1 % for OER compared to the polyhedra (AQE: 1.6 %) and SrTaO{sub 2}N polycrystals (AQE: 0.6 %). The enhanced performance from the nanoplates arises from their morphology and lower defect density. These results highlight the importance of developing new synthetic routes to high quality oxynitrides. (copyright 2017 Wiley-VCH Verlag GmbH and Co. KGaA, Weinheim)

  14. Electron transport determines the electrochemical properties of tetrahedral amorphous carbon (ta-C) thin films

    International Nuclear Information System (INIS)

    Palomäki, Tommi; Wester, Niklas; Caro, Miguel A.; Sainio, Sami; Protopopova, Vera; Koskinen, Jari; Laurila, Tomi

    2017-01-01

    Amorphous carbon based electrodes are very promising for electrochemical sensing applications. In order to better understand their structure-function relationship, the effect of film thickness on the electrochemical properties of tetrahedral amorphous carbon (ta-C) electrodes was investigated. ta-C thin films of 7, 15, 30, 50 and 100 nm were characterized in detail with Raman spectroscopy, transmission electron microscopy (TEM), conductive atomic force microscopy (c-AFM), scanning tunneling spectroscopy (STS) and X-ray absorption spectroscopy (XAS) to assess (i) the surface properties of the films, (ii) the effect of film thickness on their structure and electrical properties and (iii) the subsequent correlation with their electrochemistry. The electrochemical properties were investigated by cyclic voltammetry (CV) using two different outer-sphere redox probes, Ru(NH 3 ) 6 3+/2+ and FcMeOH, and by electrochemical impedance spectroscopy (EIS). Computational simulations using density functional theory (DFT) were carried out to rationalize the experimental findings. The characterization results showed that the sp 2 /sp 3 ratio increased with decreasing ta-C film thickness. This correlated with a decrease in mobility gap value and an increase in the average current through the films, which was also consistent with the computational results. XAS indicated that the surface of the ta-C films was always identical and composed of a sp 2 -rich layer. The CV measurements indicated reversible reaction kinetics for both outer-sphere redox probes at 7 and 15 nm ta-C films with a change to quasi-reversible behavior at a thickness of around 30 nm. The charge transfer resistance, obtained from EIS measurements, decreased with decreasing film thickness in accordance with the CV results. Based on the characterization and electrochemical results, we conclude that the reaction kinetics in the case of outer-sphere redox systems is determined mainly by the electron transport through the

  15. Resistive Switching of Ta2O5-Based Self-Rectifying Vertical-Type Resistive Switching Memory

    Science.gov (United States)

    Ryu, Sungyeon; Kim, Seong Keun; Choi, Byung Joon

    2018-01-01

    To efficiently increase the capacity of resistive switching random-access memory (RRAM) while maintaining the same area, a vertical structure similar to a vertical NAND flash structure is needed. In addition, the sneak-path current through the half-selected neighboring memory cell should be mitigated by integrating a selector device with each RRAM cell. In this study, an integrated vertical-type RRAM cell and selector device was fabricated and characterized. Ta2O5 as the switching layer and TaOxNy as the selector layer were used to preliminarily study the feasibility of such an integrated device. To make the side contact of the bottom electrode with active layers, a thick Al2O3 insulating layer was placed between the Pt bottom electrode and the Ta2O5/TaOxNy stacks. Resistive switching phenomena were observed under relatively low currents (below 10 μA) in this vertical-type RRAM device. The TaOxNy layer acted as a nonlinear resistor with moderate nonlinearity. Its low-resistance-state and high-resistance-state were well retained up to 1000 s.

  16. Characterization of BaBi2Ta2O9 prepared through amorphous precursor

    International Nuclear Information System (INIS)

    Maczka, M.; Kepinski, L.; Hermanowicz, K.; Dacko, S.; Czapla, Z.; Hanuza, J.

    2011-01-01

    Research highlights: → Formation of Bi-layered BaBi 2 Ta 2 O 9 proceeds via an intermediate fluorite phase. → Mechanochemical activation lowers the synthesis temperature by 150-200 deg. C. → The lateral size of the synthesized plate-like crystallites is about 100-200 nm. → Properties of the synthesized crystallites are different from the bulk material. - Abstract: Formation of ferroelectric BaBi 2 Ta 2 O 9 by annealing of an amorphous precursor prepared by high energy milling in ball mill has been studied by X-ray, scanning electron microscopy (SEM), Raman, infrared spectroscopy (IR), diffuse reflectivity and dielectric measurements. Our results show that formation of Bi-layered BaBi 2 Ta 2 O 9 proceeds via an intermediate fluorite phase. Mechanochemical activation allows obtaining BaBi 2 Ta 2 O 9 at short time and much lower temperatures than those required in a conventional solid state reaction. The lateral size of the plate-like crystallites is about 100-200 nm and properties of the synthesized particles are different compared to the bulk material.

  17. Artificially controlled stress anisotropy and magnetic properties of FeTaN thin films

    International Nuclear Information System (INIS)

    Deng, H.; Jarratt, J.D.; Minor, M.K.; Barnard, J.A.

    1997-01-01

    This article presents a new method of investigating internal stress effects on thin film magnetic properties, in this case magnetically soft FeTaN sputtered films. The FeTaN films were deposited on a series of oxidized silicon (111) substrates prestressed to different degrees. During sputtering all the deposition conditions were kept exactly the same for all the samples. However, anisotropic stresses with different amplitudes are systematically introduced into the films when the prestressed wafers were released. In this way, FeTaN films with compressive stress varying from 80 to 608 MPa are produced. We found that the saturation magnetostriction (λ s ), anisotropy field (H k ), initial permeability (μ i ) as well as easy axis orientation of FeTaN thin films are strongly affected by the induced stress anisotropy. A stress ratio concept is proposed as a measure of the degree of the stress anisotropy. Models for easy-hard axis switching induced by stress for magnetic films with positive magnetostriction are discussed. copyright 1997 American Institute of Physics

  18. Resistivity of Weyl semimetals NbP and TaP under pressure

    International Nuclear Information System (INIS)

    Einaga, M.; Shimizu, K.; Hu, J.; Mao, Z.Q.; Politano, A.

    2017-01-01

    The resistivity of Weyl semimetals NbP and TaP has been investigated as a function of pressure and temperature. The behaviour of the resistivity as a function of pressure and temperature is closely correlated to the location of the Weyl points compared to the Fermi energy. The rapid increase of the resistivity in TaP and NbP under the application of 4.5 and 8.0 GPa is related with the shift of Weyl points, which affords a finite density of states near the Fermi energy. Specifically, we find that under pressure the Weyl points are situated above the Fermi energy. As regards the temperature behaviour, we detect a nonmonotonous behaviour of resistivity in TaP at 8.7 and 9.8 GPa as a function of temperature, whereas in the case of NbP the behaviour is more complicate. (copyright 2017 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

  19. Resistivity of Weyl semimetals NbP and TaP under pressure

    Energy Technology Data Exchange (ETDEWEB)

    Einaga, M.; Shimizu, K. [KYOKUGEN, Graduate School of Engineering Science, Osaka University, Toyonaka (Japan); Hu, J.; Mao, Z.Q. [Department of Physics and Engineering Physics, Tulane University, New Orleans, LA (United States); Politano, A. [Fondazione Istituto Italiano di Tecnologia, Graphene Labs, Genova (Italy)

    2017-08-15

    The resistivity of Weyl semimetals NbP and TaP has been investigated as a function of pressure and temperature. The behaviour of the resistivity as a function of pressure and temperature is closely correlated to the location of the Weyl points compared to the Fermi energy. The rapid increase of the resistivity in TaP and NbP under the application of 4.5 and 8.0 GPa is related with the shift of Weyl points, which affords a finite density of states near the Fermi energy. Specifically, we find that under pressure the Weyl points are situated above the Fermi energy. As regards the temperature behaviour, we detect a nonmonotonous behaviour of resistivity in TaP at 8.7 and 9.8 GPa as a function of temperature, whereas in the case of NbP the behaviour is more complicate. (copyright 2017 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

  20. Constitutive overexpression of the TaNF-YB4 gene in transgenic wheat significantly improves grain yield.

    Science.gov (United States)

    Yadav, Dinesh; Shavrukov, Yuri; Bazanova, Natalia; Chirkova, Larissa; Borisjuk, Nikolai; Kovalchuk, Nataliya; Ismagul, Ainur; Parent, Boris; Langridge, Peter; Hrmova, Maria; Lopato, Sergiy

    2015-11-01

    Heterotrimeric nuclear factors Y (NF-Ys) are involved in regulation of various vital functions in all eukaryotic organisms. Although a number of NF-Y subunits have been characterized in model plants, only a few have been functionally evaluated in crops. In this work, a number of genes encoding NF-YB and NF-YC subunits were isolated from drought-tolerant wheat (Triticum aestivum L. cv. RAC875), and the impact of the overexpression of TaNF-YB4 in the Australian wheat cultivar Gladius was investigated. TaNF-YB4 was isolated as a result of two consecutive yeast two-hybrid (Y2H) screens, where ZmNF-YB2a was used as a starting bait. A new NF-YC subunit, designated TaNF-YC15, was isolated in the first Y2H screen and used as bait in a second screen, which identified two wheat NF-YB subunits, TaNF-YB2 and TaNF-YB4. Three-dimensional modelling of a TaNF-YB2/TaNF-YC15 dimer revealed structural determinants that may underlie interaction selectivity. The TaNF-YB4 gene was placed under the control of the strong constitutive polyubiquitin promoter from maize and introduced into wheat by biolistic bombardment. The growth and yield components of several independent transgenic lines with up-regulated levels of TaNF-YB4 were evaluated under well-watered conditions (T1-T3 generations) and under mild drought (T2 generation). Analysis of T2 plants was performed in large deep containers in conditions close to field trials. Under optimal watering conditions, transgenic wheat plants produced significantly more spikes but other yield components did not change. This resulted in a 20-30% increased grain yield compared with untransformed control plants. Under water-limited conditions transgenic lines maintained parity in yield performance. © The Author 2015. Published by Oxford University Press on behalf of the Society for Experimental Biology.

  1. On the structure of the incommensurate superlattices of 2H - TaSe2

    International Nuclear Information System (INIS)

    Withers, R.L.; Bursill, L.A.

    1979-01-01

    Reinterpretation of the neutron diffraction study of 2H-TaSe 2 by Moncton, Axe and DiSalvo (1977) reveals an ambiguity in the sense of the displacements proposed for the commensurate superlattice structure. An attempt is made to resolve this ambiguity by electrostatic and short-range energy calculations of the phase dependence of the energy of the periodic structural distortion wave. There is a fine balance between Se-Se short range repulsion, Ta-Se electrostatic and short-range repulsion and the CDW-Ta ion interaction energy terms. The analysis reveals the phase dependence of the various terms and allows the different contributions to the stability of the distortion waves to be discussed more completely than previously

  2. Influence of sequential room-temperature compressive creep on flow stress of TA2

    Science.gov (United States)

    Mengyuan, Zhang; Boqin, Gu; Jiahui, Tao

    2018-03-01

    This paper studied the sequential room temperature compressive creep and its effects on compressive properties of TA2 with stress-control loading pattern by using cylindrical compressive test specimen. The significant time-dependent deformation under constant load was observed in the TA2 at room temperature, and the deformation was dependent on the loading process under the same loading stress rate. It was also found that the occurrence of room temperature compressive creep obviously enhanced the subsequent yielding strength and flow stress of TA2 due to the increase of network dislocation density. And the effects of room temperature creep on the strain rate-stress behavior could be explained by the local mobile dislocation density model.

  3. Investigation of the phase formation and dielectric properties of Bi7Ta3O18

    International Nuclear Information System (INIS)

    Chon, M.P.; Tan, K.B.; Khaw, C.C.; Zainal, Z.; Taufiq Yap, Y.H.; Chen, S.K.; Tan, P.Y.

    2014-01-01

    Highlights: • Synthesis condition of Bi 7 TaO 3 O 18 had been determined. • Recombination of intermediate BiTaO 4 and Bi 3 TaO 7 phases are required for the Bi 7 TaO 3 O 18 phase formation. • Stable material as confirmed by thermal and structural analyses. • Typical ferroelectric showing high dielectric constants and low losses. • Resonance and thermal activated polarisation processes are responsible for the excellent dielectric characteristic. -- Abstract: Polycrystalline Bi 7 Ta 3 O 18 was synthesised at the firing temperature of 950 °C over 18 h via conventional solid state method. It crystallised in a monoclinic system with space group C2/m, Z = 4 similar to that reported diffraction pattern in the Inorganic Crystal Structure Database (ICSD), 1-89-6647. The refined lattice parameters were a = 34.060 (3) Å, b = 7.618 (9) Å, c = 6.647 (6) Å with α = γ = 90° and β = 109.210 (7), respectively. The intermediate phase was predominantly in high-symmetry cubic structure below 800 °C and finally evolved into a low-symmetry monoclinic structured, Bi 7 Ta 3 O 18 at 950 °C. The sample contained grains of various shapes with different orientations in the size ranging from 0.33–22.70 μm. The elemental analysis showed the sample had correct stoichiometry with negligible Bi 2 O 3 loss. Bi 7 Ta 3 O 18 was thermally stable and it exhibited a relatively high relative permittivity, 241 and low dielectric loss, 0.004 at room temperature, ∼30 °C and frequency of 1 MHz

  4. High-rate deposition of Ta-doped SnO2 films by reactive magnetron sputtering using a Sn–Ta metal-sintered target

    International Nuclear Information System (INIS)

    Muto, Y.; Nakatomi, S.; Oka, N.; Iwabuchi, Y.; Kotsubo, H.; Shigesato, Y.

    2012-01-01

    Ta-doped SnO 2 films were deposited on glass substrate (either unheated or heated at 200 °C) by reactive magnetron sputtering with a Sn–Ta metal-sintered target using a plasma control unit (PCU) and mid-frequency (mf, 50 kHz) unipolar pulsing. The PCU feedback system precisely controlled the flow of the reactive and sputtering gases (O 2 and Ar, respectively) by monitoring either discharge impedance or the plasma emission of the atomic O* line at 777 nm. The planar target was connected to the switching unit, which was operated in unipolar pulse mode. Power density on the target was maintained at 4.4 W cm −2 during deposition. The lowest obtained resistivity for the films deposited on heated substrate was 6.4 × 10 −3 Ωcm, where the deposition rate was 250 nm min −1 .

  5. Detailed structural characterization of the grafting of [Ta(=CHtBu)(CH2tBu)3] and [Cp*TaMe4] on silica partially dehydroxylated at 700 C and the activity of the grafted complexes toward alkane metathesis

    Energy Technology Data Exchange (ETDEWEB)

    Le Roux, Erwan; Chabanas, Mathieu; Baudouin, Anne; de Mallmann, Aimery; Coperet, Christophe; Quadrelli, E. Allesandra; Thivolle-Cazat, Jean; Basset, Jean-Marie; Lukens, Wayne; Lesage, Anne; Emsley, Lyndon; Sunley, Glenn J.

    2004-08-30

    The reaction of [Ta({double_bond}CHtBu)(CH{sub 2}tBu){sub 3}] or [Cp*Ta(CH{sub 3}){sub 4}] with a silica partially dehydroxylated at 700 C gives the corresponding monosiloxy surface complexes [({triple_bond}SiO)Ta({double_bond}CHtBu)(CH{sub 2}tBu){sub 2}] and [({triple_bond}SiO)Ta(CH{sub 3}){sub 3}Cp*] by eliminating a {sigma}-bonded ligand as the corresponding alkane (H-CH{sub 2}tBu or H-CH{sub 3}). EXAFS data show that an adjacent siloxane bridge of the surface plays the role of an extra surface ligand, which most likely stabilizes these complexes as in [({triple_bond}SiO)Ta({double_bond}CHtBu)(CH{sub 2}tBu){sub 2}({triple_bond}SiOSi{triple_bond})] (1a') and [({triple_bond}SiO)Ta(CH{sub 3}){sub 3}Cp*({triple_bond}SiOSi{triple_bond})] (2a'). In the case of [({triple_bond}SiO)Ta({double_bond}CHtBu)(CH{sub 2}tBu){sub 2}({triple_bond}SiOSi{triple_bond})], the structure is further stabilized by an additional interaction: a C-H agostic bond as evidenced by the small J coupling constant for the carbenic C-H (H{sub C-H} = 80 Hz), which was measured by J-resolved 2D solid-state NMR spectroscopy. The product selectivity in propane metathesis in the presence of [({triple_bond}SiO)Ta({double_bond}CHtBu)-(CH{sub 2}tBu){sub 2}({triple_bond}SiOSi{triple_bond})] (1a') as a catalyst precursor and the inactivity of the surface complex [({triple_bond}SiO)Ta-(CH{sub 3}){sub 3}Cp*({triple_bond}SiOSi{triple_bond})] (2a') show that the active site is required to be highly electrophilic and probably involves a metallacyclobutane intermediate.

  6. Effect of oxygen on the complexing and electrochemical processes in the NaCl-KCl-K2TaF7 melt

    International Nuclear Information System (INIS)

    Polyakova, L.P.; Kononova, Z.A.; Kremenetskij, V.G.; Polyakov, E.K.

    1997-01-01

    Using the method of linear voltametry oxygen influence on electrochemical behaviour of tantalum during NaCl-KCl-K 2 TaF 7 melt titration with sodium oxide is studied. It is shown that in NaCl-KCl-K 3 TaOF 6 and NaCl-KCl-K 2 TaF 7 -Na 2 O melts (at molar ratio O/Ta = 1 ) tantalum reduction proceeds from oxyhalide complex of TaOClF 5 -3 composition. On further titration with sodium oxide (1 5 3- complexes, but their concentration is decreased at the cost of formation of insoluble compound K 0,4 TaO 2,4 F 0,6 . When O/Ta ≥ 2,4 tantalum concentration in electrolyte is decreased up to zero and peak of tantalum reduction on voltamogram is not recorded. (author)

  7. Substitution and Redox Chemistry of [Bu(4)N](2)[Ta(6)Cl(12)(OSO(2)CF(3))(6)].

    Science.gov (United States)

    Prokopuk, Nicholas; Kennedy, Vance O.; Stern, Charlotte L.; Shriver, Duward F.

    1998-09-21

    Two sequential electrochemical reductions occur for the cluster anion [Ta(6)Cl(12)(OSO(2)CF(3))(6)](2)(-) at 0.89 and 0.29 V vs Ag/AgCl, with the generation [Ta(6)Cl(12)(OSO(2)CF(3))(6)](3)(-) and [Ta(6)Cl(12)(OSO(2)CF(3))(6)](4)(-). Chemical reduction of [Ta(6)Cl(12)(OSO(2)CF(3))(6)](2)(-) by ferrocene produces [Ta(6)Cl(12)(OSO(2)CF(3))(6)](3)(-) with the concomitant shift of the nu(SO(2)) stretch from 1002 to 1018 cm(-)(1). Reaction of [Bu(4)N](2)[Ta(6)Cl(12)(OSO(2)CF(3))(6)] (1) with [Bu(4)N]X (X = Cl, Br, I, NCS) occurs by reduction and substitution, yielding [Bu(4)N](3)[Ta(6)Cl(12)X(6)], where the clusters with X = Br, I, and NCS are new. Spectroscopic (IR and UV-vis) evidence indicates that the reduced cluster core {Ta(6)Cl(12)}(2+) is produced in reaction mixtures of 1 with the halide and pseudohalide ions. Concomitant substitution of the triflate ligands of 1 by X(-) occurs and the rates for the overall reduction and substitution increase in the order X(-) = Cl(-) < Br(-) < NCS(-) < I(-) < CN(-). Reduction of 1 with ferrocene followed by addition of [Bu(4)N]O(2)CCH(3) produces the new cluster [Ta(6)Cl(12)(O(2)CCH(3))(6)](3)(-) isolated as the tetrabutylammonium salt. Cyclic voltammetry and UV-vis spectroscopy on the new clusters [Bu(4)N](3)[Ta(6)Cl(12)X(6)] (X = Br, I, NCS, and O(2)CCH(3)) are reported. Crystal data for [Bu(4)N](3)[Ta(6)Cl(12)(NCS)(6)].CH(2)Cl(2): monoclinic, space group, P2(1)/c (No. 14); a = 25.855(6) Å, b = 21.843(6) Å, c = 16.423(3) Å; beta = 100.03(2) degrees; V = 9133(3) Å(3); Z = 4.

  8. Fabrication and evaluation of green-light emitting Ta2O5:Er, Ce co-sputtered thin films

    Directory of Open Access Journals (Sweden)

    K. Miura

    2015-01-01

    Full Text Available Erbium and cerium co-doped tantalum-oxide (Ta2O5:Er, Ce thin films were fabricated using radio-frequency co-sputtering of Ta2O5, Er2O3, and CeO2 for the first time. Enhanced green-light emission due to Er3+ that seems to be sensitized by Ce3+ was observed from the film annealed at 900 °C for 20 min. From XRD measurements of the films, the β-Ta2O5 (orthorhombic, δ-Ta2O5 (hexagonal, and (201 Ta2O5 phases seem to be very important for obtaining green PL from them. Such Ta2O5:Er, Ce co-sputtered films can be used as high-refractive-index materials of autocloned photonic crystals that can be applied to novel green-light-emitting devices, and they will also be used as multi-functional coating films that can work both as anti-reflection and down-conversion films for realizing high-efficiency silicon solar cells.

  9. Heterologous expression of wheat VERNALIZATION 2 (TaVRN2 gene in Arabidopsis delays flowering and enhances freezing tolerance.

    Directory of Open Access Journals (Sweden)

    Amadou Diallo

    Full Text Available The vernalization gene 2 (VRN2, is a major flowering repressor in temperate cereals that is regulated by low temperature and photoperiod. Here we show that the gene from Triticum aestivum (TaVRN2 is also regulated by salt, heat shock, dehydration, wounding and abscissic acid. Promoter analysis indicates that TaVRN2 regulatory region possesses all the specific responsive elements to these stresses. This suggests pleiotropic effects of TaVRN2 in wheat development and adaptability to the environment. To test if TaVRN2 can act as a flowering repressor in species different from the temperate cereals, the gene was ectopically expressed in the model plant Arabidopsis. Transgenic plants showed no alteration in morphology, but their flowering time was significantly delayed compared to controls plants, indicating that TaVRN2, although having no ortholog in Brassicaceae, can act as a flowering repressor in these species. To identify the possible mechanism by which TaVRN2 gene delays flowering in Arabidopsis, the expression level of several genes involved in flowering time regulation was determined. The analysis indicates that the late flowering of the 35S::TaVRN2 plants was associated with a complex pattern of expression of the major flowering control genes, FCA, FLC, FT, FVE and SOC1. This suggests that heterologous expression of TaVRN2 in Arabidopsis can delay flowering by modulating several floral inductive pathways. Furthermore, transgenic plants showed higher freezing tolerance, likely due to the accumulation of CBF2, CBF3 and the COR genes. Overall, our data suggests that TaVRN2 gene could modulate a common regulator of the two interacting pathways that regulate flowering time and the induction of cold tolerance. The results also demonstrate that TaVRN2 could be used to manipulate flowering time and improve cold tolerance in other species.

  10. Establishing efficient cobalt based catalytic sites for oxygen evolution on a Ta3N5 photocatalyst

    KAUST Repository

    Nurlaela, Ela; Ould-Chikh, Samy; Llorens, Isabelle; Hazemann, Jean-louis; Takanabe, Kazuhiro

    2015-01-01

    In a photocatalytic suspension system with a powder semiconductor, the interface between the photocatalyst semiconductor and catalyst should be constructed to minimize resistance for charge transfer of excited carriers. This study demonstrates an in-depth understanding of pretreatment effects on the photocatalytic O2 evolution reaction (OER) activity of visible-light-responsive Ta3N5 decorated with CoOx nanoparticles. The CoOx/Ta3N5 sample was synthesized by impregnation followed by sequential heat treat-ments under NH3 flow and air flow at various temperatures. Various characterization techniques, including X-ray diffraction (XRD), X-ray absorption spectroscopy (XAS), scanning transmission electron microscopy (STEM), and X-ray photoelectron spec-troscopy (XPS), were used to clarify the state and role of cobalt. No improvement in photocatalytic activity for OER over the bare Ta3N5 was observed for the as-impregnated CoOx/Ta3N5, likely because of insufficient contact between CoOx and Ta3N5. When the sample was treated in NH3 at high temperature, a substantial improvement in the photocatalytic activity was observed. After NH3 treatment at 700 °C, the Co0-CoOx core-shell agglomerated cobalt structure was identified by XAS and STEM. No metallic cobalt species was evident after the photocatalytic OER, indicating that the metallic cobalt itself is not essential for the reaction. Accordingly, mild oxidation (200 °C) of the NH3-treated CoOx/Ta3N5 sample enhanced photocatalytic OER activity. Oxidation at higher temperatures drastically eliminated the photocatalytic activity, most likely because of unfavorable Ta3N5 oxidation. These results suggest that the intimate contact between cobalt species and Ta3N5 facilitated at high temperature is beneficial to enhancing hole transport and that the cobalt oxide provides electrocatalytic sites for OER.

  11. Establishing efficient cobalt based catalytic sites for oxygen evolution on a Ta3N5 photocatalyst

    KAUST Repository

    Nurlaela, Ela

    2015-08-05

    In a photocatalytic suspension system with a powder semiconductor, the interface between the photocatalyst semiconductor and catalyst should be constructed to minimize resistance for charge transfer of excited carriers. This study demonstrates an in-depth understanding of pretreatment effects on the photocatalytic O2 evolution reaction (OER) activity of visible-light-responsive Ta3N5 decorated with CoOx nanoparticles. The CoOx/Ta3N5 sample was synthesized by impregnation followed by sequential heat treat-ments under NH3 flow and air flow at various temperatures. Various characterization techniques, including X-ray diffraction (XRD), X-ray absorption spectroscopy (XAS), scanning transmission electron microscopy (STEM), and X-ray photoelectron spec-troscopy (XPS), were used to clarify the state and role of cobalt. No improvement in photocatalytic activity for OER over the bare Ta3N5 was observed for the as-impregnated CoOx/Ta3N5, likely because of insufficient contact between CoOx and Ta3N5. When the sample was treated in NH3 at high temperature, a substantial improvement in the photocatalytic activity was observed. After NH3 treatment at 700 °C, the Co0-CoOx core-shell agglomerated cobalt structure was identified by XAS and STEM. No metallic cobalt species was evident after the photocatalytic OER, indicating that the metallic cobalt itself is not essential for the reaction. Accordingly, mild oxidation (200 °C) of the NH3-treated CoOx/Ta3N5 sample enhanced photocatalytic OER activity. Oxidation at higher temperatures drastically eliminated the photocatalytic activity, most likely because of unfavorable Ta3N5 oxidation. These results suggest that the intimate contact between cobalt species and Ta3N5 facilitated at high temperature is beneficial to enhancing hole transport and that the cobalt oxide provides electrocatalytic sites for OER.

  12. Ultrahigh lattice thermal conductivity in topological semimetal TaN caused by a large acoustic-optical gap.

    Science.gov (United States)

    Guo, San-Dong; Liu, Bang-Gui

    2018-03-14

    Topological semimetals may have potential applications such as in topological qubits, spintronics and quantum computations. Efficient heat dissipation is a key factor for the reliability and stability of topological semimetal-based nano-electronics devices, which is closely related to high thermal conductivity. In this work, the elastic properties and lattice thermal conductivity of TaN are investigated using first-principles calculations and the linearized phonon Boltzmann equation within the single-mode relaxation time approximation. According to the calculated bulk modulus, shear modulus and C 44 , TaN can be regarded as a potential incompressible and hard material. The room-temperature lattice thermal conductivity is predicted to be 838.62 [Formula: see text] along the a axis and 1080.40 [Formula: see text] along the c axis, showing very strong anisotropy. It is found that the lattice thermal conductivity of TaN is several tens of times higher than other topological semimetals, such as TaAs, MoP and ZrTe, which is due to the very longer phonon lifetimes for TaN than other topological semimetals. The very different atomic masses of Ta and N atoms lead to a very large acoustic-optical band gap, and then prohibit the scattering between acoustic and optical phonon modes, which gives rise to very long phonon lifetimes. Calculated results show that isotope scattering has little effect on lattice thermal conductivity, and that phonons with mean free paths larger than 20 (80) [Formula: see text] along the c direction at 300 K have little contribution to the total lattice thermal conductivity. This work implies that TaN-based nano-electronics devices may be more stable and reliable due to efficient heat dissipation, and motivates further experimental works to study lattice thermal conductivity of TaN.

  13. Ultrahigh lattice thermal conductivity in topological semimetal TaN caused by a large acoustic-optical gap

    Science.gov (United States)

    Guo, San-Dong; Liu, Bang-Gui

    2018-03-01

    Topological semimetals may have potential applications such as in topological qubits, spintronics and quantum computations. Efficient heat dissipation is a key factor for the reliability and stability of topological semimetal-based nano-electronics devices, which is closely related to high thermal conductivity. In this work, the elastic properties and lattice thermal conductivity of TaN are investigated using first-principles calculations and the linearized phonon Boltzmann equation within the single-mode relaxation time approximation. According to the calculated bulk modulus, shear modulus and C 44, TaN can be regarded as a potential incompressible and hard material. The room-temperature lattice thermal conductivity is predicted to be 838.62 W~m-1~K^{-1} along the a axis and 1080.40 W~m-1~K^{-1} along the c axis, showing very strong anisotropy. It is found that the lattice thermal conductivity of TaN is several tens of times higher than other topological semimetals, such as TaAs, MoP and ZrTe, which is due to the very longer phonon lifetimes for TaN than other topological semimetals. The very different atomic masses of Ta and N atoms lead to a very large acoustic-optical band gap, and then prohibit the scattering between acoustic and optical phonon modes, which gives rise to very long phonon lifetimes. Calculated results show that isotope scattering has little effect on lattice thermal conductivity, and that phonons with mean free paths larger than 20 (80) μm along the c direction at 300 K have little contribution to the total lattice thermal conductivity. This work implies that TaN-based nano-electronics devices may be more stable and reliable due to efficient heat dissipation, and motivates further experimental works to study lattice thermal conductivity of TaN.

  14. DEPOSITION AND PROPERTY CHARACTERISATION OF TaN COATINGS DEPOSITED WITH DIFFERENT NITROGEN CONTENTS

    Directory of Open Access Journals (Sweden)

    Gilberto Bejarano Gaitán

    Full Text Available This study focused on the study of the influence of nitrogen content on the microstructure, chemical composition, mechanical and tribological properties of TaN coatings deposited on 420 stainless steel and silicon samples (100 using the magnetron sputtering technique. For the deposition of the TaN coatings an argon/nitrogen atmosphere was used, varying the nitrogen flux between 12% and 25%. For the coating characterization, scanning electron microscopy, energydispersive X-ray spectroscopy, atomic force microscopy, X-ray diffraction (XRD, micro-Raman spectroscopy, a microhardness tester, and a ball on disc tribometer were used. A refining of the columnar structure of the coatings, accompanied by a decrease in their thickness with the increased nitrogen content was observed. Initially, fcc-TaN (111 cubic phase growth was observed; this phase was changed to the fcc-TaN (200 above N2 12%. For contents greater than N2 18%, another nitrogen-rich phase was formed and the system tended towards amorphicity, particularly for a coating with N2 25% content. The TaN-1sample deposited with N2 12% in the gas mixture presented the highest micro-hardness value with 21.3GPa and the lowest friction coefficient and wear rate with 0.02 and 1.82x10-7 (mm³/Nm, respectively. From the obtained results, an important relationship between the microstructural, mechanical and tribological properties of the coated samples and their nitrogen content was observed.

  15. Multipacting Simulations of Tuner-adjustable waveguide coupler (TaCo) with CST Particle Studio®

    CERN Document Server

    Shafqat, N; Wegner, R

    2014-01-01

    Tuner-adjustable waveguide couplers (TaCo) are used to feed microwave power to different RF structures of LINAC4. This paper studies the multipacting phenomenon for TaCo using the PIC solver of CST PS. Simulations are performed for complete field sweeps and results are analysed.

  16. Mussel inspired polymerized P(TA-TETA) for facile functionalization of carbon nanotube

    Science.gov (United States)

    Si, Shuxian; Gao, Tingting; Wang, Junhao; Liu, Qinze; Zhou, Guowei

    2018-03-01

    This article describes a novel and effective approach for non-covalent modification of carbon nanotube (CNT) via the mussel inspired polymerization of tannic acid (TA) and triethylenetetramine (TETA) and subsequent surface initiated atom transfer radical polymerization (SI-ATRP). Fourier transform infrared spectroscopy (FT-IR), thermo-gravimetric analysis (TGA), transmission electron microscope (TEM), X-ray photoelectron spectroscopy (XPS) and photograph were used to study the successful preparation of polymer brush grafted CNT (CNT-P(TA-TETA)-PDMAEMA) composite as well as the pH-responsive behavior of the composite. Furthermore, by amine protonation and in situ reduction, gold nanoparticles were successfully uploaded and the catalytic property of CNT-P(TA-TETA)-PDMAEMA/Au was investigated. We believe that the surface functionalization strategy can be extended to graphene and other substrates, and the surface properties can be regulated by grafting polymer brushes with different functionalities.

  17. Effect of Al alloying on the martensitic temperature in Ti-Ta shape memory alloys

    Energy Technology Data Exchange (ETDEWEB)

    Ferrari, Alberto; Rogal, Jutta; Drautz, Ralf [Interdisciplinary Centre for Advanced Materials Simulation, Ruhr-Universitaet Bochum (Germany)

    2017-07-01

    Ti-Ta-based alloys are promising candidates as high temperature shape memory alloys (HTSMAs) for actuators and superelastic applications. The shape memory mechanism involves a martensitic transformation between the low-temperature α'' phase (orthorhombic) and the high-temperature β phase (body-centered cubic). In order to prevent the degradation of the shape memory effect, Ti-Ta needs to be alloyed with further elements. However, this often reduces the martensitic temperature M{sub s}, which is usually strongly composition dependent. The aim of this work is to analyze how the addition of a third element to Ti-Ta alloys affects M{sub s} by means of electronic structure calculations. In particular, it will be investigated how alloying Al to Ti-Ta alters the relative stability of the α'' and β phases. This understanding will help to identify new alloy compositions featuring both a stable shape memory effect and elevated transformation temperatures.

  18. A study on the resistance switching of Ag2Se and Ta2O5 heterojunctions using structural engineering

    Science.gov (United States)

    Lee, Tae Sung; Lee, Nam Joo; Abbas, Haider; Hu, Quanli; Yoon, Tae-Sik; Lee, Hyun Ho; Le Shim, Ee; Kang, Chi Jung

    2018-01-01

    The resistive random access memory (RRAM) devices with heterostuctures have been investigated due to cycling stability, nonlinear switching, complementary resistive switching and self-compliance. The heterostructured devices can modulate the resistive switching (RS) behavior appropriately by bilayer structure with a variety of materials. In this study, the bipolar resistive switching characteristics of the bilayer structures composed of Ta2O5 and Ag2Se, which are transition-metal oxide (TMO) and silver chalcogenide, were investigated. The bilayer devices of Ta2O5 deposited on Ag2Se (Ta2O5/Ag2Se) and Ag2Se deposited on Ta2O5 (Ag2Se/Ta2O5) were fabricated for investigation of the RS characteristics by stacking sequence of Ta2O5 and Ag2Se. All operating voltages were applied to the Ag top electrode with the Pt bottom electrode grounded. The Ta2O5/Ag2Se device showed that a negative voltage sweep switched the device from high resistance state (HRS) to low resistance state (LRS) and a positive voltage sweep switched the device from LRS to HRS. On the contrary, for the Ag2Se/Ta2O5 device a positive voltage sweep switched the device from HRS to LRS, and a negative voltage sweep switched it from LRS to HRS. The polarity dependence of RS was attributed to the stacking sequence of Ta2O5 and Ag2Se. In addition, the combined heterostructured device of both bilayer stacks, Ta2O5/Ag2Se and Ag2Se/Ta2O5, exhibited the complementary switching characteristics. By using threshold switching devices, sneak path leakage can be reduced without additional selectors. The bilayer heterostructures of Ta2O5 and Ag2Se have various advantages such as self-compliance, reproducibility and forming-free stable RS. It confirms the possible applications of TMO and silver chalcogenide heterostructures in RRAM.

  19. 77 FR 42003 - TA-W-81,263, Chartis Global Services, Inc., a Subsidiary of Chartis, Inc., Regional Processing...

    Science.gov (United States)

    2012-07-17

    ... DEPARTMENT OF LABOR Employment and Training Administration TA-W-81,263, Chartis Global Services..., Houston, TX; TA-W-81,263A, Chartis Global Services, Inc., a Subsidiary of Chartis, Inc., Regional... is amending the certification (TA-W-81,263) to add ``Regional Processing Organization'' and to add...

  20. Functional studies of heading date-related gene TaPRR73, a paralog of Ppd1 in common wheat

    Directory of Open Access Journals (Sweden)

    Wenping eZhang

    2016-06-01

    Full Text Available Photoperiod response-related genes play a crucial role in duration of the plant growth. In this study, we focused on TaPRR73, a paralog of Green Revolution gene Ppd1 (TaPRR37. We found that overexpression of the truncated TaPRR73 form lacking part of the N-terminal PR domain in transgenic rice promoted heading under long day conditions. Association analysis in common wheat verified that TaPRR73 was an important agronomic photoperiod response gene that significantly affected heading date and plant height; expression analysis proved that specific alleles of TaPRR73-A1 had highly expressed levels in earlier heading lines; the distribution of haplotypes indicated that one of these alleles had been selected in breeding programs. Our results demonstrated that TaPRR73 contributed to regulation of heading date in wheat and could be useful in wheat breeding and in broadening adaptation of the crop to new regions.

  1. Preparation and Photocatalytic Properties of Sr2−xBaxTa3O10−yNz Nanosheets

    Directory of Open Access Journals (Sweden)

    Tatsumi Ishihara

    2013-01-01

    Full Text Available Sr2−xBaxTa3O10−yNz (x = 0.0, 0.5, 1.0 nanosheets were prepared by exfoliating layered perovskite compounds (CsSr2−xBaxTa3O10−yNz. The Sr1.5Ba0.5Ta3O9.7N0.2 nanosheet showed the highest photocatalytic activity for H2 production from the water/methanol system among the Sr2−xBaxTa3O9.7N0.2 nanosheets prepared. In addition, Rh-loaded Sr1.5Ba0.5Ta3O9.6N0.3 nanosheet showed the photocatalytic activity for oxygen and hydrogen production from water. The ratio of hydrogen to oxygen evolved was around two. These results indicate that the Rh-loaded Sr1.5Ba0.5Ta3O9.6N0.3 nanosheet is a potential catalyst for photocatalytic water splitting.

  2. Hydrogen spillover phenomenon: Enhanced reversible hydrogen adsorption/desorption at Ta{sub 2}O{sub 5}-coated Pt electrode in acidic media

    Energy Technology Data Exchange (ETDEWEB)

    Sata, Shunsuke [Department of Electronic Chemistry, Interdisciplinary Graduate School of Science and Engineering, Tokyo Institute of Technology, 4259-G1-5 Nagatsuta, Midori-ku, Yokohama 226-8502 (Japan); Awad, Mohamed I.; El-Deab, Mohamed S. [Department of Electronic Chemistry, Interdisciplinary Graduate School of Science and Engineering, Tokyo Institute of Technology, 4259-G1-5 Nagatsuta, Midori-ku, Yokohama 226-8502 (Japan); Department of Chemistry, Faculty of Science, Cairo University, Cairo (Egypt); Okajima, Takeyoshi [Department of Electronic Chemistry, Interdisciplinary Graduate School of Science and Engineering, Tokyo Institute of Technology, 4259-G1-5 Nagatsuta, Midori-ku, Yokohama 226-8502 (Japan); Ohsaka, Takeo, E-mail: ohsaka@echem.titech.ac.j [Department of Electronic Chemistry, Interdisciplinary Graduate School of Science and Engineering, Tokyo Institute of Technology, 4259-G1-5 Nagatsuta, Midori-ku, Yokohama 226-8502 (Japan)

    2010-04-01

    The current study is concerned with the preparation and characterization of tantalum oxide-loaded Pt (TaO{sub x}/Pt) electrodes for hydrogen spillover application. XPS, SEM, EDX and XRD techniques are used to characterize the TaO{sub x}/Pt surfaces. TaO{sub x}/Pt electrodes were prepared by galvanostatic electrodeposition of Ta on Pt from LiF-NaF (60:40 mol%) molten salts containing K{sub 2}TaF{sub 7} (20 wt%) at 800 deg. C and then by annealing in air at various temperatures (200, 400 and 600 deg. C). The thus-fabricated TaO{sub x}/Pt electrodes were compared with the non-annealed Ta/Pt and the unmodified Pt electrodes for the hydrogen adsorption/desorption (H{sub ads}/H{sub des}) reaction. The oxidation of Ta to the stoichiometric oxide (Ta{sub 2}O{sub 5}) increases with increasing the annealing temperature as revealed from XPS and X-ray diffraction (XRD) measurements. The higher the annealing temperature the larger is the enhancement in the H{sub ads}/H{sub des} reaction at TaO{sub x}/Pt electrode. The extraordinary increase in the hydrogen adsorption/desorption at the electrode annealed at 600 deg. C is explained on the basis of a hydrogen spillover-reverse spillover mechanism. The hydrogen adsorption at the TaO{sub x}/Pt electrode is a diffusion-controlled process.

  3. Evidence for Nb-Ta Occurrences in the Syn-Tectonic Pan-African Mayo Salah Leucogranite (Northern Cameroon: Constraints from Nb-Ta Oxide Mineralogy, Geochemistry and U-Pb LA-ICP-MS Geochronology on Columbite and Monazite

    Directory of Open Access Journals (Sweden)

    Periclex Martial Fosso Tchunte

    2018-04-01

    Full Text Available The Mayo Salah pluton, which is located in the North-Cameroon domain of Central African Bold Belt (CAFB, is emplaced as a laccolith in volcano-sedimentary schists of Poli series, and displays features of Rare-metal Granite (RMG. It is made of two main rock groups: (1 the metaluminous barren muscovite granite (MsG and (2 the Nb-Ta bearing peraluminous leucogranite (MsL which expresses four subtypes. The evolved Rare-element MsL is subalkaline, slightly peraluminous (ASI = 1.01–1.21, and it displays flat REE chondrite-normalized patterns with a strong negative Eu anomaly (Eu/Eu* = 0.02–0.20. It belongs to the peraluminous low phosphorus Rare-element Granites and L-type igneous rocks, as shown by the relatively low Zr/Hf (4.8–14 and Nb/Ta (1.4–9.0 ratios and the positive slope of the Zr-Hf-Nb-Ta profile in spider diagrams. The rare-element-bearing mineral is represented by columbite-group minerals (CGM and other Nb-Ta-oxides (Nb-rutile and pyrochlore supergroup minerals. The CGM is classified as Mn-columbite, with Ta# and Mn# ratios increasing from core to rim. Two stages of mineralization are identified; the earliest stage (CGM-I consists in scattered tabular or prismatic euhedral grains that were related to magmatic fractionation. The latest stage (CGM-II is expressed as a Ta-rich Mn hydrothermal CGM episode represented as rims and/overgrowths around and/or as veinlet crosscutting CGM-I or in cleavage planes of muscovite. The U-Pb dating of columbite and monazite of the Mayo Salah leucogranite indicates a late-Neoproterozoic magmatic-hydrothermal mineralization event from 603.2 ± 5.3 to 581.6 ± 7.2 Ma, as consistent with both late D2 to D3 events that were recorded in the CAFB in Cameroon, and the associated continental collision environment. The Nb-Ta mineralization of the Mayo Salah pluton provides evidence for the presence of RMG in Northern Cameroon of CAFB, and its temporal association with the youngest period of metallogenic epoch

  4. Nanospherical composite of WO{sub 3} wrapped NaTaO{sub 3}: Improved photodegradation of tetracycline under visible light irradiation

    Energy Technology Data Exchange (ETDEWEB)

    Qu, Lingnan; Lang, Junyu; Wang, Shuwei; Chai, Zhanli; Su, Yiguo; Wang, Xiaojing, E-mail: wang_xiao_jing@hotmail.com

    2016-12-01

    Graphical abstract: - Highlights: • A novel ternary NaTaO{sub 3}@WO{sub 3} photocatalyst was successfully fabricated. • NaTaO{sub 3}@WO{sub 3} composites exhibited spherical assemblies with fine WO{sub 3} nanosheets wrapped on the cube NaTaO{sub 3} nanoparticles. • NaTaO{sub 3}@WO{sub 3} showed the enhanced photocatalytic performance in the tetracycline hydrochloride degradation under visible light irradiation. • An adsorption−degradation photocatalytic mechanism promoted through a Z-type heterojunction was proposed. - Abstract: In this paper, WO{sub 3}-wrapped NaTaO{sub 3} nanospheres photocatalysts with different W/Ta molar ratios were successfully prepared via a facile hydrothermal method. The samples were characterized by X-ray diffraction, transmission and scan electron microscopy, X-ray photoelectron spectroscopy, FT-IR spectrum, UV−vis diffuse reflectance spectroscopy, and Barrett−Emmett−Teller technique. The photocatalytic activities for degrading tetracycline hydrochloride under visible light irradiation were examined. The results indicated that the as-prepared NaTaO{sub 3}@WO{sub 3} photocatalysts showed the obvious enhancement in the tetracycline hydrochloride degradation ratio, compared with the pure NaTaO{sub 3} and WO{sub 3} under visible light irradiation. The optimum percentage of NaTaO{sub 3}@WO{sub 3} composites with a 60.88% degradation rate was W:Ta = 0.3:1 in mole, which was mainly attributed to the effective separation of the photo-generated electron and hole as well as the expanding of the absorption edge to the visible region due to the spherical heterojunction by wrapping WO{sub 3} on the surface of NaTaO{sub 3}. The radicals trapping experiments demonstrated that there were multiple active species during the degrading process of TC. The possible mechanism of tetracycline hydrochloride degradation by NaTaO{sub 3}@WO{sub 3} composite was also proposed.

  5. The wheat AGC kinase TaAGC1 is a positive contributor to host resistance to the necrotrophic pathogen Rhizoctonia cerealis.

    Science.gov (United States)

    Zhu, Xiuliang; Yang, Kun; Wei, Xuening; Zhang, Qiaofeng; Rong, Wei; Du, Lipu; Ye, Xingguo; Qi, Lin; Zhang, Zengyan

    2015-11-01

    Considerable progress has been made in understanding the roles of AGC kinases in mammalian systems. However, very little is known about the roles of AGC kinases in wheat (Triticum aestivum). The necrotrophic fungus Rhizoctonia cerealis is the major pathogen of the destructive disease sharp eyespot of wheat. In this study, the wheat AGC kinase gene TaAGC1, responding to R. cerealis infection, was isolated, and its properties and role in wheat defence were characterized. R. cerealis-resistant wheat lines expressed TaAGC1 at higher levels than susceptible wheat lines. Sequence and phylogenetic analyses showed that the TaAGC1 protein is a serine/threonine kinase belonging to the NDR (nuclear Dbf2-related) subgroup of AGC kinases. Kinase activity assays proved that TaAGC1 is a functional kinase and the Asp-239 residue located in the conserved serine/threonine kinase domain of TaAGC1 is required for the kinase activity. Subcellular localization assays indicated that TaAGC1 localized in the cytoplasm and nucleus. Virus-induced TaAGC1 silencing revealed that the down-regulation of TaAGC1 transcripts significantly impaired wheat resistance to R. cerealis. The molecular characterization and responses of TaAGC1 overexpressing transgenic wheat plants indicated that TaAGC1 overexpression significantly enhanced resistance to sharp eyespot and reduced the accumulation of reactive oxygen species (ROS) in wheat plants challenged with R. cerealis. Furthermore, ROS-scavenging and certain defence-associated genes were up-regulated in resistant plants overexpressing TaAGC1 but down-regulated in susceptible knock-down plants. These results suggested that the kinase TaAGC1 positively contributes to wheat immunity to R. cerealis through regulating expression of ROS-related and defence-associated genes. © The Author 2015. Published by Oxford University Press on behalf of the Society for Experimental Biology.

  6. Overexpression of TaNAC2D displays opposite responses to abiotic stresses between seedling and mature stage of transgenic Arabidopsis

    Directory of Open Access Journals (Sweden)

    Quanjun Huang

    2016-11-01

    Full Text Available Environmental stresses frequently affect plant growth and development, and many genes have been found to be induced by unfavorable environmental conditions. Here, we reported the biological functions of TaNAC2D, a stress-related NAC (NAM, ATAF, and CUC gene from wheat. TaNAC2D showed transcriptional activator activity in yeast. TaNAC2D-GFP fusion protein was localized in the nucleus of wheat mesophyll protoplasts. TaNAC2D transcript abundance was significantly induced by NaCl, PEG6000, and abscisic acid (ABA at seedling stage, and repressed by NaCl and PEG6000 at mature plant stage. When TaNAC2D was introduced into Arabidopsis, the 35-day-old soil-grown TaNAC2D-overexpression (TaNAC2D-OX plants displayed slower stomatal closure, higher water loss rate, and more sensitivity to salt and drought stresses compared with WT plants. In contrast, TaNAC2D-OX seedlings, grown on 1/2 MS medium supplemented with different concentrations of NaCl, Mannitol, and MV, had enhanced tolerances to salt, osmotic and oxidative stresses during seed germination and post-germination periods. The opposite stress-responsive phenotypes of transgenic Arabidopsis were consistent with the expression patterns of TaNAC2D in wheat. Moreover, under high salinity and dehydration conditions, three marker genes, including NCED3, RD29A, and RD29B, were down-regulated in 35-d-old TaNAC2D-OX plants grown in soil and up-regulated in 14-d-old TaNAC2D-OX seedlings grown on 1/2 MS medium. Our results suggest that the change in growth stages and environmental conditions may regulate TaNAC2D’s function.

  7. Synthesis, characterization, and photoactivity of InTaO4 and In0.9Ni0.1TaO4 thin films prepared by electron evaporation

    International Nuclear Information System (INIS)

    Rico, V. J.; Frutos, F.; Yubero, F.; Espinos, J. P.; Gonzales-Elipe, A. R.

    2010-01-01

    InTaO 4 and In 0.9 Ni 0.1 TaO 4 thin films have been prepared by electron evaporation of successive layers of the single oxide components and posterior annealing at T>800 deg. C. The annealed thin films presented the monoclinic crystallographic structure typical of these mixed oxides. The electrical and optical behaviors of the films, assessed by C-V measurements, surface conductivity as a function of temperature, and UV-vis absorption spectroscopy, indicate that these oxides are wide band gap semiconductors with a variable dielectric constant depending on the annealing conditions. By reflection electron energy loss spectroscopy some electronic states have been found in the gap at an energy that is compatible with the activation energy deduced from the conductivity versus 1/T plots for these oxides. The photoactivity of these materials has been assessed by looking to the evolution of the wetting contact angle as a function of the irradiation time. All the films became superhydrophilic when irradiated with UV light, while the In 0.9 Ni 0.1 TaO 4 thin films also presented a small partial decrease in wetting angle when irradiated with visible photons.

  8. 78 FR 61388 - TA-W-82,705, the Boeing Company Boeing Commercial Aircraft, (BCA) Including On-Site Leased...

    Science.gov (United States)

    2013-10-03

    ... DEPARTMENT OF LABOR Employment and Training Administration TA-W-82,705, the Boeing Company Boeing... Services and Yoh Services Auburn, Washington; TA-W-82,705A, the Boeing Company Boeing Commercial Aircraft...., Triad Systems International, Volt Services and Yoh Services Everett, Washington; TA-W-82,705B, The...

  9. NaTaO3 photocatalysts of different crystalline structures for water splitting into H2 and O2

    International Nuclear Information System (INIS)

    Lin, W.-H.; Cheng, C.; Hu, C.-C.; Teng, H.

    2006-01-01

    Perovskite-type NaTaO 3 derived from a sol-gel synthesis exhibited a larger surface area and a remarkably higher photocatalytic activity in water splitting than the solid-state synthesized NaTaO 3 . The sol-gel and solid-state NaTaO 3 had different crystalline structures of monoclinic P2/m and orthorhombic Pcmn, respectively. Diffuse reflectance spectra showed that the sol-gel specimen had a slightly larger band gap. The band structure analysis revealed an indirect band gap for the sol-gel NaTaO 3 , contrary to the direct band gap of the solid-state one. The difference in the electronic structure and surface area explained the higher photocatalytic activity of the sol-gel NaTaO 3

  10. Memory window engineering of Ta2O5-x oxide-based resistive switches via incorporation of various insulating frames

    Science.gov (United States)

    Lee, Ah Rahm; Baek, Gwang Ho; Kim, Tae Yoon; Ko, Won Bae; Yang, Seung Mo; Kim, Jongmin; Im, Hyun Sik; Hong, Jin Pyo

    2016-07-01

    Three-dimensional (3D) stackable memory frames, including nano-scaled crossbar arrays, are one of the most reliable building blocks to meet the demand of high-density non-volatile memory electronics. However, their utilization has the disadvantage of introducing issues related to sneak paths, which can negatively impact device performance. We address the enhancement of complementary resistive switching (CRS) features via the incorporation of insulating frames as a generic approach to extend their use; here, a Pt/Ta2O5-x/Ta/Ta2O5-x/Pt frame is chosen as the basic CRS cell. The incorporation of Ta/Ta2O5-x/Ta or Pt/amorphous TaN/Pt insulting frames into the basic CRS cell ensures the appreciably advanced memory features of CRS cells including higher on/off ratios, improved read margins, and increased selectivity without reliability degradation. Experimental observations identified that a suitable insulating frame is crucial for adjusting the abrupt reset events of the switching element, thereby facilitating the enhanced electrical characteristics of CRS cells that are suitable for practical applications.

  11. Extraction behavior of Nb and Ta in HF solutions with tributyl phosphate

    International Nuclear Information System (INIS)

    Murakami, M.; Tsuto, S.; Ooe, K.; Goto, S.; Kudo, H.; Haba, H.; Kanaya, J.

    2013-01-01

    Extraction behavior of carrier-free Nb and Ta with tributyl phosphate (TBP) from HF solutions was studied by a batch method. Tantalum is extracted well to an organic phase, while Nb is left in an aqueous phase at 0.053-1.0 M HF concentrations. The similar extraction trends of Nb and Ta are shown in the solid phase extraction using a TBP resin. The extraction equilibria in the solid phase extraction are attained within ∼10 s. (author)

  12. Preparation of TiO2/boron-doped diamond/Ta multilayer films and use as electrode materials for supercapacitors

    Science.gov (United States)

    Shi, Chao; Li, Hongji; Li, Cuiping; Li, Mingji; Qu, Changqing; Yang, Baohe

    2015-12-01

    We report nanostructured TiO2/boron-doped diamond (BDD)/Ta multilayer films and their electrochemical performances as supercapacitor electrodes. The BDD films were grown on Ta substrates using electron-assisted hot filament chemical vapor deposition. Ti metal layers were deposited on the BDD surfaces by radio frequency magnetron sputtering, and nanostructured TiO2/BDD/Ta thin films were prepared by electrochemical etching and thermal annealing. The successful formation of TiO2 and Ta layered nanostructures was demonstrated using scanning electron and transmission electron microscopies. The electrochemical responses of these electrodes were evaluated by examining their use as electrical double-layer capacitors, using cyclic voltammetry, and galvanostatic charge/discharge and impedance measurements. When the TiO2/BDD/Ta film was used as the working electrode with 0.1 M Na2SO4 as the electrolyte, the capacitor had a specific capacitance of 5.23 mF cm-2 at a scan rate of 5 mV s-1 for a B/C ratio of 0.1% w/w. Furthermore, the TiO2/BDD/Ta film had improved electrochemical stability, with a retention of 89.3% after 500 cycles. This electrochemical behavior is attributed to the quality of the BDD, the surface roughness and electrocatalytic activities of the TiO2 layer and Ta nanoporous structures, and the synergies between them. These results show that TiO2/BDD/Ta films are promising as capacitor electrodes for special applications.

  13. Anomalous electronic structure and magnetoresistance in TaAs2.

    Science.gov (United States)

    Luo, Yongkang; McDonald, R D; Rosa, P F S; Scott, B; Wakeham, N; Ghimire, N J; Bauer, E D; Thompson, J D; Ronning, F

    2016-06-07

    The change in resistance of a material in a magnetic field reflects its electronic state. In metals with weakly- or non-interacting electrons, the resistance typically increases upon the application of a magnetic field. In contrast, negative magnetoresistance may appear under some circumstances, e.g., in metals with anisotropic Fermi surfaces or with spin-disorder scattering and semimetals with Dirac or Weyl electronic structures. Here we show that the non-magnetic semimetal TaAs2 possesses a very large negative magnetoresistance, with an unknown scattering mechanism. Density functional calculations find that TaAs2 is a new topological semimetal [ℤ2 invariant (0;111)] without Dirac dispersion, demonstrating that a negative magnetoresistance in non-magnetic semimetals cannot be attributed uniquely to the Adler-Bell-Jackiw chiral anomaly of bulk Dirac/Weyl fermions.

  14. Highly dispersed TaOx nanoparticles prepared by electrodeposition as oxygen reduction electrocatalysts for polymer electrolyte fuel cells

    KAUST Repository

    Seo, Jeongsuk

    2013-06-06

    Based on the chemical stability of group IV and V elements in acidic solutions, TaOx nanoparticles prepared by electrodeposition in an ethanol-based Ta plating bath at room temperature were investigated as novel nonplatinum electrocatalysts for the oxygen reduction reaction (ORR) in polymer electrolyte fuel cells (PEFCs). Electrodeposition conditions of Ta complexes and subsequent various heat treatments for the deposited TaOx were examined for the best performance of the ORR. TaOx particles on carbon black (CB), electrodeposited at a constant potential of -0.5 V Ag/AgCl for 10 s and then heat-treated by pure H2 flow at 523 K for 1 h, showed excellent catalytic activity with an onset potential of 0.93 VRHE (for 2 μA cm-2) for the ORR. Surface characterizations of the catalysts were performed by scanning transmission electron microscopy (STEM), transmission electron microscopy (TEM), and energy dispersive X-ray spectroscopy (EDS). The loading amounts of the electrodeposited material on the CB were determined by inductively coupled plasma atomic emission spectroscopy (ICP-AES). All the physical results suggested that high dispersion of TaOx particles on the CB surface with 2-3 nm size was critical and key for high activity. The chemical identity and modified surface structure for the deposited TaOx catalysts before and after H 2 heat treatment were analyzed by X-ray photoelectron spectroscopy (XPS). The formation of more exposed active sites on the electrode surface and enhanced electroconductivity of the tantalum oxide promoted from the H 2 treatment greatly improved the ORR performance of the electrodeposited TaOx nanoparticles on CB. Finally, the highly retained ORR activity after an accelerated durability test in an acidic solution confirmed and proved the chemical stability of the oxide nanoparticles. The high utilization of the electrodeposited TaOx nanoparticles uniformly dispersed on CB for the ORR was comparable to that of commercial Pt/CB catalysts

  15. Correlation between hardness and stress in Al-(Nb, Mo, Ta) thin films

    Energy Technology Data Exchange (ETDEWEB)

    Car, T., E-mail: car@irb.h [Rudjer Boskovic Institute, Division of Materials Science, Bijenicka cesta 54, 10000 Zagreb, P.O.B. 1016 (Croatia); Radic, N. [Rudjer Boskovic Institute, Division of Materials Science, Bijenicka cesta 54, 10000 Zagreb, P.O.B. 1016 (Croatia); Panjan, P.; Cekada, M. [Jozef Stefan Institute, Ljubljana (Slovenia); Tonejc, A. [Department of Physics, Bijenicka cesta 32, 10000 Zagreb, P.O.B. 331 (Croatia)

    2009-06-30

    The thin films of Al{sub x}Nb{sub 1-x} (95 {>=} x {>=} 20), Al{sub x}Mo{sub x} (90 {>=} x {>=} 20) and Al{sub x}Ta{sub 1-x} (95 {>=} x {>=} 20) were prepared by magnetron codeposition at room temperature. The average film thickness was from 325 to 400 nm, depending on the film composition. The structure of the as-deposited films was examined by the X-ray diffraction. The stress of the films was determined from the substrate deformation by the profilometer, and the microhardness (load 2 mN) was examined by the micro- and nano-hardness device. For the purpose of the examination of the hardness, the samples were deposited onto the sapphire wafers, while the examination of the film stress, was performed by using thin glass substrates. For all the Al-(Nb, Mo, Ta) alloy compositions, the microhardness is predominantly under the influence of the harder element, and monotonically decreases with the increase of the aluminum content. However, the microhardness of the amorphous AlTa films was higher than the bulk value of a harder element (Ta) in the alloy. A simple empirical linear relationship between the Vickers hardness, the bulk value hardness of the transition metal (harder element) and the elastic energy fraction of the identation deformation, was established. The elastic energy fraction in the microhardness is also linearly correlated with the stress in films.

  16. Crack propagation behavior of Ti-5Ta alloy in boiling nitric acid solution

    International Nuclear Information System (INIS)

    Motooka, Takafumi; Kiuchi, Kiyoshi

    1999-05-01

    The crack propagation behavior of Ti-5Ta alloy both in boiling nitric acid solution and in air at room temperature has been investigated. The crack growth rate of Ti-5Ta alloy was measured as a function of the stress intensity factor range. After the tests, the fracture surface morphology was observed by a scanning electron microscope and the crystallographic orientation was examined by X-ray diffraction analysis. Difference in the crack growth behavior was not observed in both environments. The crack growth rate in boiling nitric acid solution was similar to that in air at room temperature. Moreover, the crystallographic orientation of Ti-5Ta alloy had little effect on the fatigue behavior, because this alloy does not have the susceptibility to SCC in nitric acid solution. (author)

  17. A wheat WRKY transcription factor TaWRKY10 confers tolerance to multiple abiotic stresses in transgenic tobacco.

    Directory of Open Access Journals (Sweden)

    Chen Wang

    Full Text Available WRKY transcription factors are reported to be involved in defense regulation, stress response and plant growth and development. However, the precise role of WRKY transcription factors in abiotic stress tolerance is not completely understood, especially in crops. In this study, we identified and cloned 10 WRKY genes from genome of wheat (Triticum aestivum L.. TaWRKY10, a gene induced by multiple stresses, was selected for further investigation. TaWRKY10 was upregulated by treatment with polyethylene glycol, NaCl, cold and H2O2. Result of Southern blot indicates that the wheat genome contains three copies of TaWRKY10. The TaWRKY10 protein is localized in the nucleus and functions as a transcriptional activator. Overexpression of TaWRKY10 in tobacco (Nicotiana tabacum L. resulted in enhanced drought and salt stress tolerance, mainly demonstrated by the transgenic plants exhibiting of increased germination rate, root length, survival rate, and relative water content under these stress conditions. Further investigation showed that transgenic plants also retained higher proline and soluble sugar contents, and lower reactive oxygen species and malonaldehyde contents. Moreover, overexpression of the TaWRKY10 regulated the expression of a series of stress related genes. Taken together, our results indicate that TaWRKY10 functions as a positive factor under drought and salt stresses by regulating the osmotic balance, ROS scavenging and transcription of stress related genes.

  18. The relationship between anaphor features and antecedent retrieval: Comparing Mandarin ziji and ta-ziji

    Directory of Open Access Journals (Sweden)

    Brian eDillon

    2016-01-01

    Full Text Available In the present study we report two self-paced reading experiments that investigate antecedent retrieval processes in sentence comprehension by contrasting the real-time processing behavior of two different reflexive anaphors in Mandarin Chinese. Previous work has suggested that comprehenders initially evaluate the fit between the morphologically simple long-distance reflexive 'ziji' and the closest available subject position, only subsequently considering more structurally distant antecedents (Dillon et al., 2014; Gao et al., 2005; Liu, 2009; Li & Zhou, 2010; cf. Chen et al., 2012. In this paper, we investigate whether this locality bias effect obtains for other reflexive anaphors in Mandarin Chinese, or if it is associated specifically with the morphologically simple reflexive ziji. We do this by comparing the processing of ziji to the processing of the morphologically complex reflexive ta-ziji (lit. s/he-self. In Experiment 1, we investigate the processing of ziji, and replicate the finding of a strong locality bias effect for ziji in self-paced reading measures. In Experiment 2, we investigate the processing of the morphologically complex reflexive ta-ziji in the same structural configurations as Experiment 1. A comparison of our experiments reveals that ta-ziji shows a significantly weaker locality bias effect than ziji does. We propose that this results from the difference in the number of morphological and semantic features on the anaphor ta-ziji relative to ziji. Specifically, we propose that the additional retrieval cues associated with ta-ziji reduce interference from irrelevant representations in memory, allowing it to more reliably access an antecedent regardless its linear or structural distance. This reduced interference in turn leads to a diminished locality bias effect for the morphologically complex anaphor ta-ziji.

  19. Can We Reconcile the TA Excess and Hotspot with Auger Observations?

    Energy Technology Data Exchange (ETDEWEB)

    Globus, Noemie; Piran, Tsvi [Racah Institute of Physics, The Hebrew University of Jerusalem, 91904 Jerusalem (Israel); Allard, Denis; Parizot, Etienne; Lachaud, Cyril [Laboratoire Astroparticule et Cosmologie, Université Paris Diderot/CNRS, 10 rue A. Domon et L. Duquet, F-75205 Paris Cedex 13 (France)

    2017-02-20

    The Telescope Array (TA) shows a 20° hotspot as well as an excess of ultra-high-energy cosmic-rays (UHECRs) above 50 EeV when compared with the Auger spectrum. We consider the possibility that both the TA excess and hotspot are due to a dominant source in the northern sky. We carry out detailed simulations of UHECR propagation in both the intergalactic medium and the Galaxy, using different values for the intergalactic magnetic field. We consider two general classes of sources: transients and steady, adopting a mixed UHECR composition that is consistent with the one found by Auger. The spatial location of the sources is drawn randomly. We generate Auger-like and TA-like data sets from which we determine the spectrum, the sky maps, and the level of anisotropy. We find that, while steady sources are favored over transients, it is unlikely to account for all the currently available observational data. While we reproduce fairly well the Auger spectrum for the vast majority of the simulated data sets, most of the simulated data sets with a spectrum compatible with that of TA (at most a few percent depending on density model tested) show a much stronger anisotropy than the one observed. We find that the rare cases in which both the spectrum and the anisotropy are consistent require a steady source within ∼10 Mpc, to account for the flux excess, and a strong extragalactic magnetic field ∼10 nG, to reduce the excessive anisotropy.

  20. Preparation of TiO{sub 2}/boron-doped diamond/Ta multilayer films and use as electrode materials for supercapacitors

    Energy Technology Data Exchange (ETDEWEB)

    Shi, Chao, E-mail: sc_sq1988@163.com [Tianjin Key Laboratory of Film Electronic and Communicate Devices, School of Electronics Information Engineering, Tianjin University of Technology, Tianjin 300384 (China); Li, Hongji, E-mail: hongjili@yeah.net [Tianjin Key Laboratory of Organic Solar Cells and Photochemical Conversion, School of Chemistry and Chemical Engineering, Tianjin University of Technology, Tianjin 300384 (China); Li, Cuiping, E-mail: licp226@126.com [Tianjin Key Laboratory of Film Electronic and Communicate Devices, School of Electronics Information Engineering, Tianjin University of Technology, Tianjin 300384 (China); Li, Mingji, E-mail: limingji@163.com [Tianjin Key Laboratory of Film Electronic and Communicate Devices, School of Electronics Information Engineering, Tianjin University of Technology, Tianjin 300384 (China); Qu, Changqing, E-mail: quchangqing@tjut.edu.cn [Tianjin Key Laboratory of Film Electronic and Communicate Devices, School of Electronics Information Engineering, Tianjin University of Technology, Tianjin 300384 (China); Yang, Baohe, E-mail: bhyang207@163.com [Tianjin Key Laboratory of Film Electronic and Communicate Devices, School of Electronics Information Engineering, Tianjin University of Technology, Tianjin 300384 (China)

    2015-12-01

    Highlights: • BDD film was deposited on Ta substrate by hot filament CVD method. • Ti layer was deposited on BDD film by radio frequency magnetron sputtering. • Nanostructured TiO{sub 2}/BDD/nanoporous Ta films were prepared. • The films exhibit good capacitance performance and excellent stability. - Abstract: We report nanostructured TiO{sub 2}/boron-doped diamond (BDD)/Ta multilayer films and their electrochemical performances as supercapacitor electrodes. The BDD films were grown on Ta substrates using electron-assisted hot filament chemical vapor deposition. Ti metal layers were deposited on the BDD surfaces by radio frequency magnetron sputtering, and nanostructured TiO{sub 2}/BDD/Ta thin films were prepared by electrochemical etching and thermal annealing. The successful formation of TiO{sub 2} and Ta layered nanostructures was demonstrated using scanning electron and transmission electron microscopies. The electrochemical responses of these electrodes were evaluated by examining their use as electrical double-layer capacitors, using cyclic voltammetry, and galvanostatic charge/discharge and impedance measurements. When the TiO{sub 2}/BDD/Ta film was used as the working electrode with 0.1 M Na{sub 2}SO{sub 4} as the electrolyte, the capacitor had a specific capacitance of 5.23 mF cm{sup −2} at a scan rate of 5 mV s{sup −1} for a B/C ratio of 0.1% w/w. Furthermore, the TiO{sub 2}/BDD/Ta film had improved electrochemical stability, with a retention of 89.3% after 500 cycles. This electrochemical behavior is attributed to the quality of the BDD, the surface roughness and electrocatalytic activities of the TiO{sub 2} layer and Ta nanoporous structures, and the synergies between them. These results show that TiO{sub 2}/BDD/Ta films are promising as capacitor electrodes for special applications.

  1. Due testimonianze di Josip Vaništa

    Directory of Open Access Journals (Sweden)

    Radmila Iva Janković

    2013-12-01

    Full Text Available Radmila Iva Janković ha intervistato nel luglio 2013 Josip Vaništa, artista che aveva partecipato al gruppo Gorgona e preso parte alla residenza d'artista a Brunnenburg nel 1991, organizzata da Francesco Conz con l'obiettivo di includere il gruppo di artisti nel progetto La Livre, una monumentale edizione d'artista dedicata a Ezra Pound.

  2. Effect of Ta Additions on the Microstructure, Damping, and Shape Memory Behaviour of Prealloyed Cu-Al-Ni Shape Memory Alloys

    Directory of Open Access Journals (Sweden)

    Safaa N. Saud

    2017-01-01

    Full Text Available The influence of Ta additions on the microstructure and properties of Cu-Al-Ni shape memory alloys was investigated in this paper. The addition of Ta significantly affects the green and porosity densities; the minimum percentage of porosity was observed with the modified prealloyed Cu-Al-Ni-2.0 wt.% Ta. The phase transformation temperatures were shifted towards the highest values after Ta was added. Based on the damping capacity results, the alloy of Cu-Al-Ni-3.0 wt.% Ta has very high internal friction with the maximum equivalent internal friction value twice as high as that of the prealloyed Cu-Al-Ni SMA. Moreover, the prealloyed Cu-Al-Ni SMAs with the addition of 2.0 wt.% Ta exhibited the highest shape recovery ratio in the first cycle (i.e., 100% recovery, and when the number of cycles is increased, this ratio tends to decrease. On the other hand, the modified alloys with 1.0 and 3.0 wt.% Ta implied a linear increment in the shape recovery ratio with increasing number of cycles. Polarization tests in NaCl solution showed that the corrosion resistance of Cu-Al-Ni-Ta SMA improved with escalating Ta concentration as shown by lower corrosion current densities, higher corrosion potential, and formation of stable passive film.

  3. Effect of Ta Additions on the Microstructure, Damping, and Shape Memory Behaviour of Prealloyed Cu-Al-Ni Shape Memory Alloys.

    Science.gov (United States)

    Saud, Safaa N; Hamzah, E; Bakhsheshi-Rad, H R; Abubakar, T

    2017-01-01

    The influence of Ta additions on the microstructure and properties of Cu-Al-Ni shape memory alloys was investigated in this paper. The addition of Ta significantly affects the green and porosity densities; the minimum percentage of porosity was observed with the modified prealloyed Cu-Al-Ni-2.0 wt.% Ta. The phase transformation temperatures were shifted towards the highest values after Ta was added. Based on the damping capacity results, the alloy of Cu-Al-Ni-3.0 wt.% Ta has very high internal friction with the maximum equivalent internal friction value twice as high as that of the prealloyed Cu-Al-Ni SMA. Moreover, the prealloyed Cu-Al-Ni SMAs with the addition of 2.0 wt.% Ta exhibited the highest shape recovery ratio in the first cycle (i.e., 100% recovery), and when the number of cycles is increased, this ratio tends to decrease. On the other hand, the modified alloys with 1.0 and 3.0 wt.% Ta implied a linear increment in the shape recovery ratio with increasing number of cycles. Polarization tests in NaCl solution showed that the corrosion resistance of Cu-Al-Ni-Ta SMA improved with escalating Ta concentration as shown by lower corrosion current densities, higher corrosion potential, and formation of stable passive film.

  4. Effect of ternary alloying elements on the shape memory behavior of Ti-Ta alloys

    International Nuclear Information System (INIS)

    Buenconsejo, Pio John S.; Kim, Hee Young; Miyazaki, Shuichi

    2009-01-01

    The effect of ternary alloying elements (X = V, Cr, Fe, Zr, Hf, Mo, Sn, Al) on the shape memory behavior of Ti-30Ta-X alloys was investigated. All the alloying elements decreased the martensitic transformation temperatures. The decrease in the martensitic transformation start (M s ) temperature due to alloying was affected by the atomic size and number of valence electrons of the alloying element. A larger number of valence electrons and a smaller atomic radius of an alloying element decreased the M s more strongly. The effect of the alloying elements on suppressing the aging effect on the shape memory behavior was also investigated. It was found that the additions of Sn and Al to Ti-Ta were effective in suppressing the effect of aging on the shape memory behavior, since they strongly suppress the formation of ω phase during aging treatment. For this reason the Ti-30Ta-1Al and Ti-30Ta-1Sn alloys exhibited a stable high-temperature shape memory effect during thermal cycling.

  5. Microstructure evolution and liquid phase separation in Ta-O hypermonotectic melts during laser-cladding

    Directory of Open Access Journals (Sweden)

    *Hai-ou Yang,

    2018-05-01

    Full Text Available A three-layer Ta2O5-containing coating was successfully fabricated by laser cladding on a pure Ta substrate. The maximum thickness of such a coating is about 1.6 mm. The microstructure, phase constitution and elemental distribution in the coating were investigated. Results show that the coating has been metallurgically bonded to the Ta substrate and the microstructure exhibits a graded change along the deposition direction from Ta substrate to the top of coating. In the layers I and II of the graded coating, the microstructure evolution can be confirmed as a result of hypomonotectic reaction, but in the layer Ⅲ it was formed by hypermonotectic reaction. At the top of coating, the microstructure was still homogeneous although liquid phase separation had occurred,which can be attributed to the fact that the O-rich droplets do not have enough time to float at high cooling rate.The theoretical calculation results show that during laser cladding, the solidification time of the melt pool was less than 0.1 s, which fits well with the results from the experiment.

  6. A new compound - Ta3Pb : manufacture, structure and properties

    International Nuclear Information System (INIS)

    Tuleushev, A.Zh.; Tuleushev, Yu.Zh.; Volodin, V.N.; Zhakanbaev, E.A.

    2003-01-01

    For the first time by the magnetron sputtering and tantalum deposition on substrates from molybdenum and tungsten the covers presenting the lead solution in cubic α-tantalum (up to 2.5 at % Pb) were obtained. The lead dissolution is accompanying by the Ta lattice parameter increasing from 0.3314 to 0.3321 nm in the lead concentration range from 0.2 to 2.5 at. % Pb. The cryogenic examinations of the synthesised covers conducted by four-probes electric resistance method show the absence the superconductivity up to the 4.2 K temperature. So, for the first time the Ta 2 Pb compound with A15 structure was synthesised and data for its identification were determined

  7. EDITORIAL: TaCoNa-Photonics 2008 TaCoNa-Photonics 2008

    Science.gov (United States)

    Chigrin, Dmitry N.; Busch, Kurt; Lavrinenko, Andrei V.

    2009-11-01

    This special section on theoretical and computational nano-photonics features papers presented at the first International Workshop on Theoretical and Computational Nano-Photonics (TaCoNa-Photonics 2008) held in Bad Honnef, Germany, 3-5 December 2008. The workshop covered a broad range of topics related to current developments and achievements in this interdisciplinary area of research. Since the late 1960s, the word `photonics' has been understood as the science of generating, controlling, and detecting light. Nowadays, a routine fabrication of complex structures with micro- and nano-scale dimensions opens up many new and exciting possibilities in photonics. The science of generating, routing and detecting light in micro- and nano-structured matter, `nano-photonics', is becoming more important both in research and technology and offers many promising applications. The inherently sub-wavelength character of the structures that nano-photonics deals with challenges modern theoretical and computational physics and engineering with many nontrivial questions: Up to what length-scale can one use a macroscopic phenomenological description of matter? Where is the interface between the classical and quantum description of light in nano-scale structures? How can one combine different physical systems, different time- and length-scales in a single computational model? How can one engineer nano-structured materials in order to achieve the desired optical properties for particular applications? Any attempt at answering these kinds of questions is impossible without the joint efforts of physicists, engineers, applied mathematicians and programmers. This is the reason why the major goal of the TaCoNa-Photonics workshops is to provide a forum where theoreticians and specialists in numerical methods from all branches of physics, engineering sciences and mathematics can compare their results, report on novel results and breakthroughs, and discuss new challenges ahead. In order to

  8. A highly uniform ZnO/NaTaO3 nanocomposite: Enhanced self-sensitized degradation of colored pollutants under visible light

    International Nuclear Information System (INIS)

    Xing, Guanjie; Tang, Changhe; Zhang, Bo; Zhao, Lanxiao; Su, Yiguo; Wang, Xiaojing

    2015-01-01

    In this study, a highly uniform ZnO/NaTaO 3 composite was prepared via simple hydrothermal synthesis. XRD confirmed the composite was constructed by pure cubic phase of NaTaO 3 and hexagonal phase of ZnO. SEM analysis showed that as-prepared ZnO/NaTaO 3 shaped as an irregular ginger with an obviously smaller size than that of pure ZnO without obvious agglomeration. EDS mapping demonstrated that the four elements (Na, Ta, O, Zn) in the composite were very uniformly distributed. The photocatalytic behaviors of as-prepared composites were studied in the degradation of methylene blue both under UV and visible irradiation. The bare ZnO showed the highest activity with 99.8% methylene blue (MB) photodegraded in 70 min under UV light irradiation whereas 94% photodegraded rate was achieved for ZnO/NaTaO 3 . More importantly, the uniform composite of ZnO/NaTaO 3 exhibited effective degradation of methylene blue under visible light which can be attributed to the well dyes adsorption abilities and the high efficiency of electron separation, induced by the synergistic effect between ZnO and NaTaO 3 . It is confirmed the dye rather than a semiconductor is excited under visible light irradiation and a self-sensitized photocatalytic mechanism was then proposed based on the experimental results. - Graphical abstract: Visible light photocatalytic activity of ZnO/NaTaO 3 and proposed schematic of self-sensitization directed photogradation of MB. - Highlights: • Highly uniform ZnO/NaTaO 3 photocatalysts were fabricated by hydrothermal method. • ZnO/NaTaO 3 composite exhibited effective degradation of MB under visible light. • ZnO/NaTaO 3 composite effectively promoted dye adsorption and electrons separation. • A self-sensitized photocatalytic mechanism was proposed for the degradation of dye

  9. Mesoporous (Ta, Nb3W7 Modified with Stearic Acid Used as Solid Acids for Esterification

    Directory of Open Access Journals (Sweden)

    Fei Chang

    2017-01-01

    Full Text Available Mesoporous solid acids Ta3W7 and Nb3W7 were prepared from TaCl5 and NbCl5 with WCl6 in the presence of stearic acid (SA via a sol-gel method, respectively. For comparison, mesoporous Ta3W7-P123 mixed oxides and mesoporous Nb3W7-P123 mixed oxides were synthesized in the same way. The catalysts were characterized through TGA, XRD, SEM, TEM, BET, and NH3-TPD. Experimental results showed that Ta3W7-SA and Nb3W7-SA exhibited several advantages such as higher activity, shorter preparation period, lower cost, stronger acid sites, and higher surface area, which had potential to be used as mesoporous heterogeneous catalysts in biodiesel production.

  10. International collaboration on CESR-TA program

    International Nuclear Information System (INIS)

    Flanagan, John; Suetsugu, Yusuke

    2009-01-01

    An international collaboration on the CESR-TA (Cornell Electron Storage Ring-Test Accelerator) program, which is a program to investigate electron cloud instability (ECI) issues in the positron damping ring of the ILC (International Linear-Collider), is currently underway a Cornell University, KEK is supporting the program through the development of an X-ray beam profile monitor system to measure the extremely small beam size, and through the development of clearing electrodes to mitigate the ECI. (author)

  11. TaPT: Temperature-Aware Dynamic Cache Optimization for Embedded Systems

    Directory of Open Access Journals (Sweden)

    Tosiron Adegbija

    2017-12-01

    Full Text Available Embedded systems have stringent design constraints, which has necessitated much prior research focus on optimizing energy consumption and/or performance. Since embedded systems typically have fewer cooling options, rising temperature, and thus temperature optimization, is an emergent concern. Most embedded systems only dissipate heat by passive convection, due to the absence of dedicated thermal management hardware mechanisms. The embedded system’s temperature not only affects the system’s reliability, but can also affect the performance, power, and cost. Thus, embedded systems require efficient thermal management techniques. However, thermal management can conflict with other optimization objectives, such as execution time and energy consumption. In this paper, we focus on managing the temperature using a synergy of cache optimization and dynamic frequency scaling, while also optimizing the execution time and energy consumption. This paper provides new insights on the impact of cache parameters on efficient temperature-aware cache tuning heuristics. In addition, we present temperature-aware phase-based tuning, TaPT, which determines Pareto optimal clock frequency and cache configurations for fine-grained execution time, energy, and temperature tradeoffs. TaPT enables autonomous system optimization and also allows designers to specify temperature constraints and optimization priorities. Experiments show that TaPT can effectively reduce execution time, energy, and temperature, while imposing minimal hardware overhead.

  12. Superconductor-Metal-Insulator transition in two dimensional Ta thin Films

    Science.gov (United States)

    Park, Sun-Gyu; Kim, Eunseong

    2013-03-01

    Superconductor-insulator transition has been induced by tuning film thickness or magnetic field. Recent electrical transport measurements of MoGe, Bi, Ta thin films revealed an interesting intermediate metallic phase which intervened superconducting and insulating phases at certain range of magnetic field. Especially, Ta thin films show the characteristic IV behavior at each phase and the disorder tuned intermediate metallic phase [Y. Li, C. L. Vicente, and J. Yoon, Physical Review B 81, 020505 (2010)]. This unexpected metallic phase can be interpreted as a consequence of vortex motion or contribution of fermionic quasiparticles. In this presentation, we report the scaling behavior during the transitions in Ta thin film as well as the transport measurements in various phases. Critical exponents v and z are obtained in samples with wide ranges of disorder. These results reveal new universality class appears when disorder exceeds a critical value. Dynamical exponent z of Superconducting sample is found to be 1, which is consistent with theoretical prediction of unity. z in a metallic sample is suddenly increased to be approximately 2.5. This critical exponent is much larger than the value found in other system and theoretical prediction. We gratefully acknowledge the financial support by the National Research Foundation of Korea through the Creative Research Initiatives.

  13. Neutron diffraction study on the mechanism of the topotactic reduction of 2HTaS 2 electrodes

    Science.gov (United States)

    Riekel, C.; Reznik, H. G.; Schöllhorn, R.

    1980-09-01

    The dynamic investigation by neutron diffraction of the topotactic reduction of 2HTaS 2 electrodes in {K+}/{D2O} electrolyte to the ionic layered hydrate K +0.5(D 2O) 0.5[TaS 2] 0.5- is shown to proceed via third-stage K +x(D 2O) y[TaS 2] 3x- , second-stage K +x(D 2O) y [TaS 2] 2x- , and first-stage K +x(D 2O) y[TaS 2] x- intermediates. A comparative study by X-ray diffraction on the cathodic intercalation of 2HTaS 2 and 2HNbS 2 electrodes with hydrated main group and transition metal ions reveals analogous behavior; the formation of higher-stage intermediates is supposedly correlated with stable electronic layer states. Influence of kinetic factors is observed for larger guest cations such as transition metal complexes and organic ions. CdI 2-type host lattices with an octahedral environment of intralayer cations shown different reaction pathways, although the occurrence of intermediate states (at least in the nucleation phase) can be demonstrated. It is concluded that the presence of ordered intermediate states is a general phenomenon in topotactic electrode processes of layered dichalcogenides.

  14. Studies on Ta-Ni alloys as high-temperature braze for SiC-SiC joined products; Untersuchungen zu Ta-Ni-Legierungen als Hochtemperaturlot fuer SiC-SiC Verbunde

    Energy Technology Data Exchange (ETDEWEB)

    Triebert, Anke; Matthey, Bjoern; Martin, Hans-Peter [Fraunhofer Institut fuer Keramische Technologien und Systeme (IKTS), Dresden (Germany)

    2011-07-01

    Active metal brazes have been already established for a number of decades. The current progress of processing technologies and engineering require new and powerful materials also for high-temperature applications. Up to now there are little technically and industrially applicable brazing materials for operation temperatures above 800 C. The investigations described in this paper concerning the Ta-Ni system intend to be the start of a braze material development, which delivers ceramic-ceramic or ceramic-metal joined products. Besides principal considerations and experiments with regard to the investigated material system of Ta-Ni active metal brazing tests to join SIC-SIC components are presented. The joined ceramic component samples are characterized focusing on their materials structure within the joining zone, their crystalline phases of the braze and their mechanical strength at room temperature and high temperatures. The achieved properties demonstrate that Ta-Ni brazes have the potential for future high temperature brazes for ceramics materials. (orig.)

  15. TaFlo2-A1, an ortholog of rice Flo2, is associated with thousand grain weight in bread wheat (Triticum aestivum L.).

    Science.gov (United States)

    Sajjad, Muhammad; Ma, Xiaoling; Habibullah Khan, Sultan; Shoaib, Muhammad; Song, Yanhong; Yang, Wenlong; Zhang, Aimin; Liu, Dongcheng

    2017-10-16

    The Flo2 gene is a member of a conserved gene family in plants. This gene has been found to be related to thousand grain weight (TGW) in rice. Its orthologs in hexaploid wheat were cloned, and the haplotype variation in TaFlo2-A1 was tested for association with TGW. The cloned sequences of TaFlo2-A1, TaFlo2-B1 and TaFlo2-D1 contained 23, 23 and 24 exons, respectively. The deduced proteins of TaFlo2-A1 (1734 aa), TaFlo2-B1 (1698 aa) and TaFlo2-D1 (1682 aa) were highly similar (>94%) and exhibited >77% similarity with the rice FLO2 protein. Like the rice FLO2 protein, four tetratricopeptide repeat (TPR) motifs were observed in the deduced TaFLO2 protein. An 8-bp InDel (-10 to -17 bp) in the promoter region and five SNPs in first intron of TaFlo2-A1 together formed two haplotypes, TaFlo2-A1a and TaFlo2-A1b, in bread wheat. TaFlo2 was located on homeologous group 2 chromosomes. TaFlo2-A1 was inferred to be located on deletion bin '2AL1-0.85-1.00'. The TaFlo2-A1 haplotypes were characterized in the Chinese Micro Core Collection (MCC) and Pakistani wheat collection using the molecular marker TaFlo2-Indel8. TaFlo2-A1 was found to be associated with TGW but not with grain number per spike (GpS) in both the MCC and Pakistani wheat collections. The frequency of TaFlo2-A1b (positive haplotype) was low in commercial wheat cultivars; thus this haplotype can be selected to improve grain weight without negatively affecting GpS. The expression level of TaFlo2-A1 in developing grains at 5 DAF (days after flowering) was positively correlated with TGW in cultivars carrying the positive haplotype. This study will likely lead to additional investigations to understand the regulatory mechanism of the Flo2 gene in hexaploid wheat. Furthermore, the newly developed molecular marker 'TaFlo2-InDel8' could be incorporated into the kit of wheat breeders for use in marker-assisted selection.

  16. ABI-like transcription factor gene TaABL1 from wheat improves multiple abiotic stress tolerances in transgenic plants.

    Science.gov (United States)

    Xu, Dong-Bei; Gao, Shi-Qing; Ma, You-Zhi; Xu, Zhao-Shi; Zhao, Chang-Ping; Tang, Yi-Miao; Li, Xue-Yin; Li, Lian-Cheng; Chen, Yao-Feng; Chen, Ming

    2014-12-01

    The phytohormone abscisic acid (ABA) plays crucial roles in adaptive responses of plants to abiotic stresses. ABA-responsive element binding proteins (AREBs) are basic leucine zipper transcription factors that regulate the expression of downstream genes containing ABA-responsive elements (ABREs) in promoter regions. A novel ABI-like (ABA-insensitive) transcription factor gene, named TaABL1, containing a conserved basic leucine zipper (bZIP) domain was cloned from wheat. Southern blotting showed that three copies were present in the wheat genome. Phylogenetic analyses indicated that TaABL1 belonged to the AREB subfamily of the bZIP transcription factor family and was most closely related to ZmABI5 in maize and OsAREB2 in rice. Expression of TaABL1 was highly induced in wheat roots, stems, and leaves by ABA, drought, high salt, and low temperature stresses. TaABL1 was localized inside the nuclei of transformed wheat mesophyll protoplast. Overexpression of TaABL1 enhanced responses of transgenic plants to ABA and hastened stomatal closure under stress, thereby improving tolerance to multiple abiotic stresses. Furthermore, overexpression of TaABL1 upregulated or downregulated the expression of some stress-related genes controlling stomatal closure in transgenic plants under ABA and drought stress conditions, suggesting that TaABL1 might be a valuable genetic resource for transgenic molecular breeding.

  17. The current status and prospect of the TA experiment

    Energy Technology Data Exchange (ETDEWEB)

    Kasahara, K. [Faculty of Systems Engineering, Dept. of Electronic and Information Systems, Minuma-ku, Saitama-shi, Saitama (Japan)

    2005-07-01

    The Telescope Array (TA) experiment is designed to observe cosmic-ray-induced air showers at extremely high energies. It is being deployed in a desert of Utah (Usa); an array of 3 m{sup 2} scintillation counters will be distributed over 760 km{sup 2} and 3 sets of air fluorescence telescopes will be placed in the perimeter of the array. Its primary purpose is to make a decisive measurement of the cosmic ray spectrum in the GZK (Greisen, Zatsepin and Kuzmin) cutoff region. We expect the first data from the TA in the spring 2007. As its unique features are included: 1) hybrid measurement planned down to 10{sup 17.5} eV; 2) calibration of fluorescence detection by using artificial air showers generated by an electron line; and 3) interaction model calibration by the LHC. (author)

  18. Survey of Technologies to Support Reuse of Gloveboxes at LANL TA-55

    International Nuclear Information System (INIS)

    Cadwallader, L.C.; Pinson, P.A.

    1998-01-01

    This report is a summary of ideas and technologies available to support reuse of plutonium gloveboxes at the Los Alamos National Laboratory (LANL) Technical Area 55 (TA-55). This work is the second of two deliverables in the task to enhance glovebox design for longevity and reusability at TA-55. The report presents several design change suggestions to be evaluated for their feasibility by LANL glovebox designers. The report also describes some techniques to be evaluated by LANL for their usefulness in reducing glovebox waste

  19. Properties of half-Heusler compounds TaIrGe by using first-principles calculations

    Energy Technology Data Exchange (ETDEWEB)

    Wei, JunHong [Henan Normal University, College of Physics and Information Engineering, Xinxiang, Henan (China); Henan Institute of Science and Technology, School of Mechanical and Electrical Engineering, Xinxiang, Henan (China); Wang, Guangtao [Henan Normal University, College of Physics and Information Engineering, Xinxiang, Henan (China)

    2017-05-15

    The electronic structures, optical and thermoelectric properties of ternary half-Heusler compound TaIrGe were investigated by using the first-principles and Boltzmann transport theory. Spin-orbit coupling (SOC) removed the degeneracy of VBM, and then decreased the Seebeck coefficients and power factor. From the compressive to tensile strain, the band gap gradually increases from 0.96 to 1.11 eV, accompanied by the absorption coefficient peak red-shift. The effective mass (m{sup *}{sub DOS}) of VBM and CBM gradually increases from the compressive to tensile strain, which enhances the Seebeck coefficient and power factor. Our results indicate that the electronic structures, optical and thermoelectric properties of TaIrGe can be effectively tuned by the strain and TaIrGe can be used as an important photoelectric and thermoelectric material in the future. (orig.)

  20. Robust TaNx diffusion barrier for Cu-interconnect technology with subnanometer thickness by metal-organic plasma-enhanced atomic layer deposition

    International Nuclear Information System (INIS)

    Kim, H.; Detavenier, C.; Straten, O. van der; Rossnagel, S.M.; Kellock, A.J.; Park, D.-G.

    2005-01-01

    TaN x diffusion barriers with good barrier properties at subnanometer thickness were deposited by plasma-enhanced atomic layer deposition (PE-ALD) from pentakis(dimethylamino)Ta. Hydrogen and/or nitrogen plasma was used as reactants to produce TaN x thin films with a different nitrogen content. The film properties including the carbon and oxygen impurity content were affected by the nitrogen flow during the process. The deposited film has nanocrystalline grains with hydrogen-only plasma, while the amorphous structure was obtained for nitrogen plasma. The diffusion barrier properties of deposited TaN films for Cu interconnects have been studied by thermal stress test based on synchrotron x-ray diffraction. The results indicate that the PE-ALD TaN films are good diffusion barriers even at a small thickness as 0.6 nm. Better diffusion barrier properties were obtained for higher nitrogen content. Based on a diffusion kinetics analysis, the nanocrystalline microstructure of the films was responsible for the better diffusion barrier properties compared to polycrystalline PE-ALD TaN films deposited from TaCl 5

  1. Particle size dependence on oxygen reduction reaction activity of electrodeposited TaOx catalysts in acidic media

    KAUST Repository

    Seo, J.; Cha, Dong Kyu; Takanabe, Kazuhiro; Kubota, J.; Domen, K.

    2013-01-01

    The size dependence of the oxygen reduction reaction activity was studied for TaOx nanoparticles electrodeposited on carbon black for application to polymer electrolyte fuel cells (PEFCs). Compared with a commercial Ta2O5 material, the ultrafine

  2. Influence of cold deformation on martensite transformation and mechanical properties of Ti-Nb-Ta-Zr alloy

    International Nuclear Information System (INIS)

    Wang Liqiang; Lu Weijie; Qin Jining; Zhang Fan; Zhang Di

    2009-01-01

    Ti-35Nb-2Ta-3Zr alloy was fabricated by vacuum consumable arc melting furnace and hot pressing. Microstructure and phase transformation of solution-treated (ST) and cold-rolled (CR) plates of Ti-Nb-Ta-Zr alloy were observed. Different microstructure of strain-induced martensite transformation during cold deformation were investigated. With the increase of reduction of cold rolling, microstructure of α''-phase changed from acicular martensite to butterfly shaped martensite and showed variant crossed and cross-hatched when the reduction of cold rolling was over 60%. Mechanical properties and SEM images of the fracture surface indicated that the alloy fabricated by cold deformation showed favorable strength and plasticity. Owing to the excellent cold workability and biomedical safety of elements of Nb, Ta and Zr, Ti-Nb-Ta-Zr alloy contributed much to medical applications

  3. The Na+ transporter, TaHKT1;5-D, limits shoot Na+ accumulation in bread wheat

    KAUST Repository

    Byrt, Caitlin Siobhan

    2014-10-01

    Bread wheat (Triticum aestivum L.) has a major salt tolerance locus, Kna1, responsible for the maintenance of a high cytosolic K+/Na+ ratio in the leaves of salt stressed plants. The Kna1 locus encompasses a large DNA fragment, the distal 14% of chromosome 4DL. Limited recombination has been observed at this locus making it difficult to map genetically and identify the causal gene. Here, we decipher the function of TaHKT1;5-D, a candidate gene underlying the Kna1 locus. Transport studies using the heterologous expression systems Saccharomyces cerevisiae and Xenopus laevis oocytes indicated that TaHKT1;5-D is a Na+-selective transporter. Transient expression in Arabidopsis thaliana mesophyll protoplasts and in situ polymerase chain reaction indicated that TaHKT1;5-D is localised on the plasma membrane in the wheat root stele. RNA interference-induced silencing decreased the expression of TaHKT1;5-D in transgenic bread wheat lines which led to an increase in the Na+ concentration in the leaves. This indicates that TaHKT1;5-D retrieves Na+ from the xylem vessels in the root and has an important role in restricting the transport of Na+ from the root to the leaves in bread wheat. Thus, TaHKT1;5-D confers the essential salinity tolerance mechanism in bread wheat associated with the Kna1 locus via shoot Na+ exclusion and is critical in maintaining a high K+/Na+ ratio in the leaves. These findings show there is potential to increase the salinity tolerance of bread wheat by manipulation of HKT1;5 genes.

  4. The Na+ transporter, TaHKT1;5-D, limits shoot Na+ accumulation in bread wheat

    KAUST Repository

    Byrt, Caitlin Siobhan; Xu, Bo; Krishnan, Mahima; Lightfoot, Damien; Athman, Asmini; Jacobs, Andrew Keith; Watson-Haigh, Nathan S.; Plett, Darren; Munns, Rana; Tester, Mark A.; Gilliham, Matthew

    2014-01-01

    Bread wheat (Triticum aestivum L.) has a major salt tolerance locus, Kna1, responsible for the maintenance of a high cytosolic K+/Na+ ratio in the leaves of salt stressed plants. The Kna1 locus encompasses a large DNA fragment, the distal 14% of chromosome 4DL. Limited recombination has been observed at this locus making it difficult to map genetically and identify the causal gene. Here, we decipher the function of TaHKT1;5-D, a candidate gene underlying the Kna1 locus. Transport studies using the heterologous expression systems Saccharomyces cerevisiae and Xenopus laevis oocytes indicated that TaHKT1;5-D is a Na+-selective transporter. Transient expression in Arabidopsis thaliana mesophyll protoplasts and in situ polymerase chain reaction indicated that TaHKT1;5-D is localised on the plasma membrane in the wheat root stele. RNA interference-induced silencing decreased the expression of TaHKT1;5-D in transgenic bread wheat lines which led to an increase in the Na+ concentration in the leaves. This indicates that TaHKT1;5-D retrieves Na+ from the xylem vessels in the root and has an important role in restricting the transport of Na+ from the root to the leaves in bread wheat. Thus, TaHKT1;5-D confers the essential salinity tolerance mechanism in bread wheat associated with the Kna1 locus via shoot Na+ exclusion and is critical in maintaining a high K+/Na+ ratio in the leaves. These findings show there is potential to increase the salinity tolerance of bread wheat by manipulation of HKT1;5 genes.

  5. Phonon and thermal properties of exfoliated TaSe{sub 2} thin films

    Energy Technology Data Exchange (ETDEWEB)

    Yan, Z.; Jiang, C.; Renteria, J. [Nano-Device Laboratory, Department of Electrical Engineering, Bourns College of Engineering, University of California–Riverside, Riverside, California 92521 (United States); Pope, T. R.; Tsang, C. F.; Stickney, J. L.; Salguero, T. T., E-mail: salguero@uga.edu, E-mail: balandin@ee.ucr.edu [Department of Chemistry, University of Georgia, Athens, Georgia 30602 (United States); Goli, P. [Materials Science and Engineering Program, Bourns College of Engineering, University of California–Riverside, Riverside, California 92521 (United States); Balandin, A. A., E-mail: salguero@uga.edu, E-mail: balandin@ee.ucr.edu [Nano-Device Laboratory, Department of Electrical Engineering, Bourns College of Engineering, University of California–Riverside, Riverside, California 92521 (United States); Materials Science and Engineering Program, Bourns College of Engineering, University of California–Riverside, Riverside, California 92521 (United States)

    2013-11-28

    We report on the phonon and thermal properties of thin films of tantalum diselenide (2H-TaSe{sub 2}) obtained via the “graphene-like” mechanical exfoliation of crystals grown by chemical vapor transport. The ratio of the intensities of the Raman peak from the Si substrate and the E{sub 2g} peak of TaSe{sub 2} presents a convenient metric for quantifying film thickness. The temperature coefficients for two main Raman peaks, A{sub 1g} and E{sub 2g}, are −0.013 and −0.0097 cm{sup −1}/{sup o}C, respectively. The Raman optothermal measurements indicate that the room temperature thermal conductivity in these films decreases from its bulk value of ∼16 W/mK to ∼9 W/mK in 45-nm thick films. The measurement of electrical resistivity of the field-effect devices with TaSe{sub 2} channels shows that heat conduction is dominated by acoustic phonons in these van der Waals films. The scaling of thermal conductivity with the film thickness suggests that the phonon scattering from the film boundaries is substantial despite the sharp interfaces of the mechanically cleaved samples. These results are important for understanding the thermal properties of thin films exfoliated from TaSe{sub 2} and other metal dichalcogenides, as well as for evaluating self-heating effects in devices made from such materials.

  6. TaUBA, a UBA domain-containing protein in wheat (Triticum aestivum L.), is a negative regulator of salt and drought stress response in transgenic Arabidopsis.

    Science.gov (United States)

    Li, Xiao; Zhang, Shuang-shuang; Ma, Jun-xia; Guo, Guang-yan; Zhang, Xue-yong; Liu, Xu; Bi, Cai-li

    2015-05-01

    TaUBA functions as a negative regulator of salt and drought stress response in transgenic Arabidopsis, either the UBA domain or the zinc finger domain is crucial for TaUBA's function. TaUBA (DQ211935), which is a UBA domain-containing protein in wheat, was cloned and functionally characterized. Southern blot suggested that TaUBA is a low copy gene in common wheat. qRT-PCR assay showed that the expression of TaUBA was strongly induced by salt and drought stress. When suffering from drought and salt stresses, lower proline content and much higher MDA content in the TaUBA overexpressors were observed than those of the wild-type control, suggesting TaUBA may function as a negative regulator of salt and drought stress response in plants. To study whether the UBA domain or the zinc finger domain affects the function of TaUBA, TaUBAΔUBA (deletion of UBA domain) and TaUBA-M (Cys464Gly and Cys467Gly) overexpression vectors were constructed and transformed into Arabidopsis. Upon drought and salt stresses, the TaUBAΔUBA-and TaUBA-M-overexpressed plants accumulated much more proline and lower MDA than the wild-type control, the TaUBA-overexpressors lost water more quickly than TaUBAΔUBA-and TaUBA-M-overexpressed plants as well as the wild-type control, suggesting that overexpression of TaUBAΔUBA or TaUBA-M improved the drought and salt tolerance of transgenic Arabidopsis plants and the possibility of ubiquitination role in the regulation of osmolyte synthesis and oxidative stress responses in mediating stress tolerance. qRT-PCR assay of stress-related genes in transgenic plants upon drought and salt stresses suggested that TaUBA may function through down-regulating some stress related-transcription factors and by regulating P5CSs to cope with osmotic stress.

  7. Optoelectronic properties of CC2TA towards a good TADF material

    Science.gov (United States)

    Mishra, Ashok Kumar

    2018-05-01

    2,4-bis{f3-(9H-carbazol-9-yl)-9H-carbazol-9-yl}-6-phenyl-1,3,5-triazine (CC2TA) is a triazine derivatives in which the acceptor phenyltriazine unit is used as the central skeleton and donor bicarbazole units are bonded to both ends of the skeleton. Molecular orbital calculations exhibit that the HOMO and LUMO are locally allocated chiefly in the bicarbazole and phenyltriazine units, respectively. There are a class of organic molecules and polymers which exhibit semiconductor behavior because of nearly free conjugate π-electrons. Hopping of these electrons in molecules forms different excited singlet and triplet states named as excitons. Some of these organic molecules can be set to emit photons by triplet-singlet excitonic transition via a process called Thermally Activated Delayed Fluorescence (TADF) which is exploited for designing the Organic Light Emitting diode (OLED.) CC2TA is one of these reported noble metal-free TADF molecules which offers unique opto electronic properties arising from the reverse intersystem crossing between the lowest singlet (S) and triplet (T) excited states. Its ability to harvest triplet excitons for fluorescence through facilitated reverse intersystem crossing (T→S) could directly impact their properties and performances, which is attractive for a wide variety of low-cost optoelectronic device. In the present study, the CC2TA compounds have been taken up for the investigation of various optoelectronic properties including the thermally activated delayed fluorescence (TADF) by using the Koopmans Method and Density Functional Theory. The present study discusses the utility of the CC2TA organic semiconductor as a suitable TADF material essential for developing an efficient Organic Light Emitting Diode (OLED).

  8. Influence of Different Substrates on Laser Induced Damage Thresholds at 1064 nm of Ta2O5 Films

    International Nuclear Information System (INIS)

    Cheng, Xu; Jian-Yong, Ma; Yun-Xia, Jin; Hong-Bo, He; Jian-Da, Shao; Zheng-Xiu, Fan

    2008-01-01

    Ta 2 O 5 films are prepared on Si, BK7, fused silica, antireflection (AR) and high reflector (HR) substrates by electron beam evaporation method, respectively. Both the optical property and laser induced damage thresholds (LIDTs) at 1064 nm of Ta 2 O 5 films on different substrates are investigated before and after annealing at 673K for 12 h. It is shown that annealing increases the refractive index and decreases the extinction index, and improves the O/Ta ratio of the Ta 2 O 5 films from 2.42 to 2.50. Moreover, the results show that the LIDTs of the Ta 2 O 5 films are mainly correlated with three parameters: substrate property, substoichiometry defect in the films and impurity defect at the interface between the substrate and the films. Details of the laser induced damage models in different cases are discussed

  9. First-principles investigations on structural, elastic, electronic properties and Debye temperature of orthorhombic Ni3Ta under pressure

    Science.gov (United States)

    Li, Pan; Zhang, Jianxin; Ma, Shiyu; Jin, Huixin; Zhang, Youjian; Zhang, Wenyang

    2018-06-01

    The structural, elastic, electronic properties and Debye temperature of Ni3Ta under different pressures are investigated using the first-principles method based on density functional theory. Our calculated equilibrium lattice parameters at 0 GPa well agree with the experimental and previous theoretical results. The calculated negative formation enthalpies and elastic constants both indicate that Ni3Ta is stable under different pressures. The bulk modulus B, shear modulus G, Young's modulus E and Poisson's ratio ν are calculated by the Voigt-Reuss-Hill method. The bigger ratio of B/G indicates Ni3Ta is ductile and the pressure can improve the ductility of Ni3Ta. In addition, the results of density of states and the charge density difference show that the stability of Ni3Ta is improved by the increasing pressure. The Debye temperature ΘD calculated from elastic modulus increases along with the pressure.

  10. Development of Ta3N5 as an Efficient Visible Light-responsive Photocatalyst for Water Oxidation

    KAUST Repository

    Nurlaela, Ela

    2015-01-01

    phase sample. The photophysical properties of Ta3N5, such as the absorption coefficient, carrier mobility, and carrier lifetime, have been experimentally measured by synthesizing Ta3N5 thin films. Very low kinetic properties with very low transport

  11. Role of spin mixing conductance in spin pumping: Enhancement of spin pumping efficiency in Ta/Cu/Py structures

    Energy Technology Data Exchange (ETDEWEB)

    Deorani, Praveen; Yang, Hyunsoo, E-mail: eleyang@nus.edu.sg [Department of Electrical and Computer Engineering, National University of Singapore, 117576 Singapore (Singapore)

    2013-12-02

    From spin pumping measurements in Ta/Py devices for different thicknesses of Ta, we determine the spin Hall angle to be 0.021–0.033 and spin diffusion length to be 8 nm in Ta. We have also studied the effect of changing the properties of non-magnet/ferromagnet interface by adding a Cu interlayer. The experimental results show that the effective spin mixing conductance increases in the presence of Cu interlayer for Ta/Cu/Py devices whereas it decreases in Pt/Cu/Py devices. Our findings allow the tunability of the spin pumping efficiency by adding a thin interlayer at the non-magnet/ferromagnet interface.

  12. Double Dirac Point Semimetal in Two-Dimensional Material: Ta2Se3

    OpenAIRE

    Ma, Yandong; Jing, Yu; Heine, Thomas

    2017-01-01

    Here, we report by first-principles calculations one new stable 2D Dirac material, Ta2Se3 monolayer. For this system, stable layered bulk phase exists, and exfoliation should be possible. Ta2Se3 monolayer is demonstrated to support two Dirac points close to the Fermi level, achieving the exotic 2D double Dirac semimetal. And like 2D single Dirac and 2D node-line semimetals, spin-orbit coupling could introduce an insulating state in this new class of 2D Dirac semimetals. Moreover, the Dirac fe...

  13. Novel NAC transcription factor TaNAC67 confers enhanced multi-abiotic stress tolerances in Arabidopsis.

    Directory of Open Access Journals (Sweden)

    Xinguo Mao

    Full Text Available Abiotic stresses are major environmental factors that affect agricultural productivity worldwide. NAC transcription factors play pivotal roles in abiotic stress signaling in plants. As a staple crop, wheat production is severely constrained by abiotic stresses whereas only a few NAC transcription factors have been characterized functionally. To promote the application of NAC genes in wheat improvement by biotechnology, a novel NAC gene designated TaNAC67 was characterized in common wheat. To determine its role, transgenic Arabidopsis overexpressing TaNAC67-GFP controlled by the CaMV-35S promoter was generated and subjected to various abiotic stresses for morphological and physiological assays. Gene expression showed that TaNAC67 was involved in response to drought, salt, cold and ABA treatments. Localization assays revealed that TaNAC67 localized in the nucleus. Morphological analysis indicated the transgenics had enhanced tolerances to drought, salt and freezing stresses, simultaneously supported by enhanced expression of multiple abiotic stress responsive genes and improved physiological traits, including strengthened cell membrane stability, retention of higher chlorophyll contents and Na(+ efflux rates, improved photosynthetic potential, and enhanced water retention capability. Overexpression of TaNAC67 resulted in pronounced enhanced tolerances to drought, salt and freezing stresses, therefore it has potential for utilization in transgenic breeding to improve abiotic stress tolerance in crops.

  14. Surface morphology and preferential orientation growth of TaC crystals formed by chemical vapor deposition

    Energy Technology Data Exchange (ETDEWEB)

    Xiong Xiang, E-mail: Xiong228@sina.co [State Key Lab for Powder Metallurgy, Central South University, Changsha 410083 (China); Chen Zhaoke; Huang Baiyun; Li Guodong [State Key Lab for Powder Metallurgy, Central South University, Changsha 410083 (China); Zheng Feng [School of Material Science and Engineering, Central South University, Changsha 410083 (China); Xiao Peng; Zhang Hongbo [State Key Lab for Powder Metallurgy, Central South University, Changsha 410083 (China)

    2009-04-02

    TaC film was deposited on (002) graphite sheet by isothermal chemical vapor deposition using TaCl{sub 5}-Ar-C{sub 3}H{sub 6} mixtures, with deposition temperature 1200 {sup o}C and pressure about 200 Pa. The influence of deposition position (or deposition rate) on preferential orientation and surface morphology of TaC crystals were investigated by X-ray diffraction and scanning electron microscopy methods. The deposits are TaC plus trace of C. The crystals are large individual columns with pyramidal-shape at deposition rate of 32.4-37.3 {mu}m/h, complex columnar at 37.3-45.6 {mu}m/h, lenticular-like at 45.6-54.6 {mu}m/h and cauliflower-like at 54.6-77.3 {mu}m/h, with <001>, near <001>, <110> and no clear preferential orientation, respectively. These results agree in part with the preditions of the Pangarov's model of the relationship between deposition rate and preferential growth orientation. The growth mechanism of TaC crystals in <001>, near <001>, <111> and no clear preferential orientation can be fairly explained by the growth parameter {alpha} with Van der Drift's model, deterioration model and Meakin model. Furthermore, a nucleation and coalescence model is also proposed to explain the formation mechanism of <110> lenticular-like crystals.

  15. Mechanical properties and biocompatibility in alloy Ti-Ta system containing oxygen

    International Nuclear Information System (INIS)

    Ruiz, S.L.M.; Grandini, C.R.; Claro, A.P.R.A.

    2010-01-01

    Due to the excellent properties such as corrosion resistance, good mechanical strength/density, good performance at high temperatures, Ti is very useful in the chemical industry and aerospace. Currently, their use has expanded to the field of biomaterials, due to its excellent biocompatibility and reduced elasticity modulus, favouring the production of orthopaedic and dental prostheses. Promising alloys are the Ti-Ta system and researches have been directed to describe and understand the behavior of this system. In this paper, samples of Ti-Ta alloys containing 8 and 16% (wt%) containing interstitial oxygen were prepared and characterized by density, xray diffraction, hardness, elasticity modulus measurements and in vitro cytotoxicity tests. (author)

  16. Geology of the Western Part of Los Alamos National Laboratory (TA-3 to TA-16), Rio Grande Rift, New Mexico

    Energy Technology Data Exchange (ETDEWEB)

    C.J.Lewis; A.Lavine; S.L.Reneau; J.N.Gardner; R.Channell; C.W.Criswell

    2002-12-01

    We present data that elucidate the stratigraphy, geomorphology, and structure in the western part of Los Alamos National Laboratory between Technical Areas 3 and 16 (TA-3 and TA-16). Data include those gathered by geologic mapping of surficial, post-Bandelier Tuff strata, conventional and high-precision geologic mapping and geochemical analysis of cooling units within the Bandelier Tuff, logging of boreholes and a gas pipeline trench, and structural analysis using profiles, cross sections, structure contour maps, and stereographic projections. This work contributes to an improved understanding of the paleoseismic and geomorphic history of the area, which will aid in future seismic hazard evaluations and other investigations. The study area lies at the base of the main, 120-m (400-ft) high escarpment formed by the Pajarito fault, an active fault of the Rio Grande rift that bounds Los Alamos National Laboratory on the west. Subsidiary fracturing, faulting, and folding associated with the Pajarito fault zone extends at least 1,500 m (5,000 ft) to the east of the main Pajarito fault escarpment. Stratigraphic units in the study area include upper units of the Tshirege Member of the early Pleistocene Bandelier Tuff, early Pleistocene alluvial fan deposits that predate incision of canyons on this part of the Pajarito Plateau, and younger Pleistocene and Holocene alluvium and colluvium that postdate drainage incision. We discriminate four sets of structures in the area between TA-3 and TA-16: (a) north-striking faults and folds that mark the main zone of deformation, including a graben in the central part of the study area; (b) north-northwest-striking fractures and rare faults that bound the eastern side of the principal zone of deformation and may be the surface expression of deep-seated faulting; (c) rare northeast-striking structures near the northern limit of the area associated with the southern end of the Rendija Canyon fault; and (d) several small east

  17. Structure of the oxide film on Ti–6Ta alloy after immersion test in 8 mol/L boiling nitric acid medium

    Energy Technology Data Exchange (ETDEWEB)

    Guo, Dizi, E-mail: diziguo@126.com; Yang, Yingli; Wu, Jinping; Zhao, Bin; Zhao, Hengzhang; Su, Hangbiao; Lu, Yafeng

    2013-08-15

    Highlights: •Structure of the oxide film on Ti–6Ta alloy is studied by depth profile XPS. •TiO{sub 2} and Ta{sub 2}O{sub 5} are found in the top layer of the oxide film. •High valence oxide evolutes form Ti{sub 2}O{sub 3} and TaO. •Shielding effect of Ta{sub 2}O{sub 5} leads to the enhanced corrosion resistance of Ti–Ta alloy. -- Abstract: By using X-ray photoelectron spectroscopy (XPS), X-ray diffractometer (XRD) and scanning electron microscopy (SEM), we investigate the corrosion behavior and the structure of the oxide film of Ti–6Ta alloy that is subjected to the immersion corrosion test in 8 mol/L boiling nitric acid for 432 h. Based on the phase constitution indentified by depth profile XPS, the oxide film could be divided into three sub-layers along its thickness direction: the chemical stable TiO{sub 2} and Ta{sub 2}O{sub 5} are present in layer I; the sub-oxide Ti{sub 2}O{sub 3} and TaO are present in the layer II and layer III, and the high valence oxide evolutes from their sub-oxide gradually. Owing to the shielding effect of Ta{sub 2}O{sub 5}, the corrosion rate of the Ti–6Ta alloy decreases from 0.051 mm/y to 0.014 mm/y with increasing immersion time, showing an excellent corrosion resistance in 8 mol/L boiling nitric acid.

  18. Synthesis, crystal structure, and photocatalytic activity of a new two-layer Ruddlesden-Popper phase, Li2CaTa2O7

    International Nuclear Information System (INIS)

    Liang Zhenhua; Tang Kaibin; Shao Qian; Li Guocan; Zeng Suyuan; Zheng Huagui

    2008-01-01

    A new two-layer Ruddlesden-Popper phase Li 2 CaTa 2 O 7 has been synthesized for the first time. The detailed structure determination of Li 2 CaTa 2 O 7 performed by powder X-ray diffraction (XRD) and electron microscopy (ED) shows that it crystallizes in the space group Fmmm [a∼5.5153(1), b∼5.4646(1), c∼18.2375(3)A]. UV-visible diffuse reflection spectrum of the prepared Li 2 CaTa 2 O 7 indicates that it had absorption in the UV region. The photocatalytic activity of the Li 2 CaTa 2 O 7 powders was evaluated by degradation of RhB molecules in water under ultra visible light irradiation. The results showed that Li 2 CaTa 2 O 7 has high photocatalytic activity at room temperature. Therefore, the preparation and properties studies of Li 2 CaTa 2 O 7 with a two-layer Ruddlesden-Popper structure suggest potential future applications in photocatalysis. - Graphical abstract: Crystal structure of a two-layer Ruddlesden-Popper phase Li 2 CaTa 2 O 7 A new two-layer Ruddlesden-Popper phase Li 2 CaTa 2 O 7 has been synthesized for the first time. Li 2 CaTa 2 O 7 crystallizes in the space group Fmmm determined by powder X-ray and electron diffraction. UV-visible diffuse reflection spectra and the photocatalytic degradation of RhB molecules in water under ultra visible light irradiation show that Li 2 CaTa 2 O 7 is a potential material in photocatalysis

  19. TaCIPK29, a CBL-interacting protein kinase gene from wheat, confers salt stress tolerance in transgenic tobacco.

    Directory of Open Access Journals (Sweden)

    Xiaomin Deng

    Full Text Available Calcineurin B-like protein-interacting protein kinases (CIPKs have been found to be responsive to abiotic stress. However, their precise functions and the related molecular mechanisms in abiotic stress tolerance are not completely understood, especially in wheat. In the present study, TaCIPK29 was identified as a new member of CIPK gene family in wheat. TaCIPK29 transcript increased after NaCl, cold, methyl viologen (MV, abscisic acid (ABA and ethylene treatments. Over-expression of TaCIPK29 in tobacco resulted in increased salt tolerance, which was demonstrated by higher germination rates, longer root lengths and better growth status of transgenic tobacco plants compared to controls when both were treated with salt stress. Physiological measurements indicated that transgenic tobacco seedlings retained high K(+/Na(+ ratios and Ca(2+ content by up-regulating some transporter genes expression and also possessed lower H2O2 levels and reduced membrane injury by increasing the expression and activities of catalase (CAT and peroxidase (POD under salt stress. Moreover, transgenic lines conferred tolerance to oxidative stress by increasing the activity and expression of CAT. Finally, TaCIPK29 was located throughout cells and it preferentially interacted with TaCBL2, TaCBL3, NtCBL2, NtCBL3 and NtCAT1. Taken together, our results showed that TaCIPK29 functions as a positive factor under salt stress and is involved in regulating cations and reactive oxygen species (ROS homeostasis.

  20. TamiR159 directed wheat TaGAMYB cleavage and its involvement in anther development and heat response.

    Directory of Open Access Journals (Sweden)

    Yu Wang

    Full Text Available In Arabidopsis and rice, miR159-regulated GAMYB-like family transcription factors function in flower development and gibberellin (GA signaling in cereal aleurone cells. In this study, the involvement of miR159 in the regulation of its putative target TaGAMYB and its relationship to wheat development were investigated. First, we demonstrated that cleavage of TaGAMYB1 and TaGAMYB2 was directed by miR159 using 5'-RACE and a transient expression system. Second, we overexpressed TamiR159, TaGAMYB1 and mTaGAMYB1 (impaired in the miR159 binding site in transgenic rice, revealing that the accumulation in rice of mature miR159 derived from the precursor of wheat resulted in delayed heading time and male sterility. In addition, the number of tillers and primary branches in rice overexpressing mTaGAMYB1 increased relative to the wild type. Our previous study reported that TamiR159 was downregulated after two hours of heat stress treatment in wheat (Triticum aestivum L.. Most notably, the TamiR159 overexpression rice lines were more sensitive to heat stress relative to the wild type, indicating that the downregulation of TamiR159 in wheat after heat stress might participate in a heat stress-related signaling pathway, in turn contributing to heat stress tolerance.

  1. Molecular characterization and expression analysis of three homoeologous Ta14S genes encoding 14-3-3 proteins in wheat (Triticum aestivum L.

    Directory of Open Access Journals (Sweden)

    Xinguo Wang

    2016-06-01

    Full Text Available The purpose of this study was to characterize Ta14S homoeologs and assess their functions in wheat seed development. The genomic and cDNA sequences of three Ta14S homoeologous genes encoding 14-3-3 proteins were isolated. Sequence analysis revealed that the three homoeologs consisted of five exons and four introns and were very highly conserved in the coding regions and in exon/intron structure, whereas the cDNA sequences were variable in the 5′ and 3′-UTR. The three genes, designated as Ta14S-2A, Ta14S-2B and Ta14S-2D, were located in homoeologous group 2 chromosomes. The polypeptide chains of the three Ta14S genes were highly similar. These genes were most homologous to Hv14A from barley. Real-time quantitative PCR indicated that the three Ta14S genes were differentially expressed in different organs at different developmental stages and all exhibited greater expression in primary roots of 1-day-old germlings than in other tissues. Comparison of the expression patterns of the three homoeologous genes at different times after pollination also revealed that their expression was developmentally regulated. The transcription of Ta14S-2B was clearly higher during seed germination, whereas expressions of Ta14S-2A and Ta14S-2D were up-regulated at the beginning of seed imbibition (0–12 h, but declined thereafter. The results suggested that the three Ta14S homoeologous genes have regulatory roles in seed development and germination.

  2. Field investigations of soils at TA-19, TA-26, TA-73 and TA-0, SWMU aggregate 0-D and 016

    International Nuclear Information System (INIS)

    McFadden, L.D.

    1995-01-01

    Field based investigations of the general soil-geomorphic characteristics were carried out at TA-19, -26, -73, -0, Aggregate 0-D and -016 in order to provide information for utilization in ongoing and anticipated LANL ERP (Environmental Restoration Project) activities at these sites. These investigations show that soils exhibiting diverse morphologic character, varying ages, and relations to landforms characterize these sites. A review of recent and ongoing soils studies also shows that soil textural, chemical, and mineralogical characteristics may profoundly influence the migration and/or retardation of a variety of potential contaminants initially placed in direct contact with soils, or that encounter soils during subsurface percolation or discharge. Soil-geomorphic relations also provide important insights into recent site erosion, deposition or other surficial processes that must, be considered as part of environmental assessment of a given site and remediation; and, the planned geomorphic mapping activities at each site, as well as other associated activities (e.g, geophysical survey, site sampling) are accordingly appropriate and necessary with respect to identification of significant soil relations at each site. Specific and general recommendations in consideration of important findings regarding the possible impacts of soil development of the nature of contaminant behavior at various sites are provided to help guide sampling and analysis activities during ERP investigations outlined in the RFI Work Plan for Operational Unit-1071

  3. Variable substrate temperature deposition of CoFeB film on Ta for manipulating the perpendicular coercive forces

    Energy Technology Data Exchange (ETDEWEB)

    Lakshmanan, Saravanan; Rao, Subha Krishna [Nanotechnology Research Centre, SRM University, Kattankulathur, Chennai 603203 (India); Muthuvel, Manivel Raja [Defence Metallurgical Research Laboratory (DMRL), Hyderabad 500058 (India); Chandrasekaran, Gopalakrishnan [Nanotechnology Research Centre, SRM University, Kattankulathur, Chennai 603203 (India); Therese, Helen Annal, E-mail: helen.a@ktr.srmuniv.ac.in [Nanotechnology Research Centre, SRM University, Kattankulathur, Chennai 603203 (India)

    2017-08-01

    Highlights: • Ta/CoFeB(50 nm)/Ta thin films were deposited at various substrate temperatures (T{sub s}). • CoFeB films deposited at T{sub s} such as RT, 450 °C, 475 °C and 500 °C exhibited perpendicular coercivity. • CoFeB deposited at 475 °C displayed a higher coercivity of 315 Oe and a low M{sub s} of 169 emu/cc. • The enhanced crystallization of CoFeB at the Ta/CoFeB interface results in higher H{sub c} (⟂). - Abstract: Magnetization of Ta/CoFeB/Ta trilayer films with thick layer of CoFeB deposited under different substrate temperatures (T{sub s}) via ultra-high vacuum DC sputtering technique has been measured with the applied magnetic field parallel and perpendicular to the plane of the film respectively to study the perpendicular coercive forces of the film. The samples were further analyzed for its structural, topological, morphological, and electrical transport properties. The core chemical states for the elements present in the CoFeB thin film were analyzed by XPS studies. Magnetization studies reveal the existence of perpendicular coercive forces in CoFeB films deposited only at certain temperatures such as RT, 450 °C, 475 °C and 500 °C. CoFeB film deposited at 475 °C exhibited a maximum coercivity of 315 Oe and a very low saturation magnetization (M{sub s}) of 169 emu/cc in perpendicular direction. This pronounced effect in perpendicular coercive forces observed for CoFeB475 could be attributed to the effect of temperature in enhancing the crystallization of the film at the Ta/CoFeB interfaces. However at temperatures higher than 475 °C the destruction of the Ta/CoFeB interface due to intermixing of Ta and CoFeB results in the disappearance of magnetic anisotropy.

  4. TA53:19 Reverb Chamber Quick-Look

    Energy Technology Data Exchange (ETDEWEB)

    Bishofberger, Kip A. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

    2016-05-19

    Within Building 19 of TA-53, a screen room has been evaluated for use as a reverb chamber (with deep gratitude to Dale Dalmas and Greg Dale for their assistance). With minimal additional sealing of the chamber, we expect the Q to increase even more, and thus field levels for the same RF source power. Future studies need to determine leakage field levels, which will define maximum achievable field levels.

  5. Substrate bias effects on composition and coercivity of CoCrTa/Cr thin films on canasite and glass

    Science.gov (United States)

    Deng, Y.; Lambeth, D. N.; Sui, X.; Lee, L.-L.; Laughlin, D. E.

    1993-05-01

    CoCrTa/Cr thin films were prepared by rf diode sputtering onto canasite and glass substrates at various bias voltages from two targets of different compositions (Co82.8Cr14.6Ta2.6 and Co86Cr12Ta2). While Auger depth profile analysis indicates that there is some broadening at the CoCrTa-Cr interface, x-ray fluorescence spectroscopy reveals that changes in alloy composition due to the resputtering processes are even more prominent. For both targets, as the substrate bias increases the Co content in the films declines, and the magnetization decreases. The maximum film coercivity appears to correlate to the final film composition. By investigating the results from both targets, it is concluded that the coercivity reaches a maximum when the film composition is in the neighborhood of Co84Cr13Ta3. Thus, to optimize the coercivity different bias voltages are required for each target. Excessive substrate bias, however, leads to films with low magnetization and coercivity.

  6. Ab initio calculations of ideal strength and lattice instability in W-Ta and W-Re alloys

    Science.gov (United States)

    Yang, Chaoming; Qi, Liang

    2018-01-01

    An important theoretical criterion to evaluate the ductility of metals with a body-centered cubic (bcc) lattice is the mechanical failure mode of their perfect crystals under tension along ; directions. When the tensile stress reaches the ideal tensile strength, the pure W crystal fails by a cleavage fracture along the {100 } plane so that it is intrinsically brittle. To discover the strategy to improve its ductility, we performed density functional theory and density functional perturbation theory calculations to study the ideal tensile strength and the lattice instability under tension for both W-Ta and W-Re alloys. Anisotropic linear elastic fracture mechanics (LEFM) theory and Rice's criterion were also applied to analyze the mechanical instability at the crack tip under tension based on the competition between cleavage propagation and dislocation emission. The results show that the intrinsic ductility can be achieved in both W-Ta and W-Re, however, by different mechanisms. Even though W-Ta alloys with low Ta concentrations are still intrinsically brittle, the intrinsic ductility of W-Ta alloys with high Ta concentrations is promoted by elastic shear instability before the cleavage failure. The intrinsic ductility of W-Re alloys is produced by unstable transverse phonon waves before the cleavage failure, and the corresponding phonon mode is related to the generation of 1/2 {2 ¯11 } dislocation in bcc crystals. The ideal tensile calculations, phonon analyses, and anisotropic LEFM examinations are mutually consistent in the evaluation of intrinsic ductility. These results bring us physical insights on the ductility-brittle mechanisms of W alloys under extreme stress conditions.

  7. Effect of nitrogen addition and annealing temperature on superelastic properties of Ti-Nb-Zr-Ta alloys

    Energy Technology Data Exchange (ETDEWEB)

    Tahara, Masaki [Institute of Materials Science, University of Tsukuba, Tsukuba, Ibaraki 305-8573 (Japan); Kim, Hee Young, E-mail: heeykim@ims.tsukuba.ac.jp [Institute of Materials Science, University of Tsukuba, Tsukuba, Ibaraki 305-8573 (Japan); Hosoda, Hideki [Precision and Intelligence Laboratory, Tokyo Institute of Technology, Yokohama 226-8503 (Japan); Nam, Tae-hyun [School of Materials Science and Engineering. A, Structural Materials: Properties, Microstructure and Processingnd ERI, Gyeongsang National University, 900 Gazwadong, Jinju, Gyeongnam 660-701 (Korea, Republic of); Miyazaki, Shuichi, E-mail: miyazaki@ims.tsukuba.ac.jp [Institute of Materials Science, University of Tsukuba, Tsukuba, Ibaraki 305-8573 (Japan); School of Materials Science and Engineering. A, Structural Materials: Properties, Microstructure and Processingnd ERI, Gyeongsang National University, 900 Gazwadong, Jinju, Gyeongnam 660-701 (Korea, Republic of)

    2010-10-15

    Research highlights: In this study, the effects of composition and annealing temperature on microstructure, shape memory effect and superelastic properties were investigated in Ti-Nb-4Zr-2Ta-N alloys by measuring stress-strain curves at various temperatures and using transmission electron microscopy. Dissolution of {alpha} phase increases M{sub s} and decreases the critical stress for slip for the Ti-22Nb-4Zr-2Ta alloy while it causes the decrease of M{sub s} and the increase of the critical stress for slip for the Ti-20Nb-4Zr-2Ta-0.6N alloy. The different effect of dissolution of {alpha} phase can be attributed to the fact that N is absorbed in {alpha} phase. - Abstract: The composition dependence of the mechanical properties and martensitic transformation behavior of Ti-Nb-4Zr-2Ta-N alloys is investigated. The effect of annealing temperature on the microstructural evolution and superelastic properties in the N-added and N-free alloys is compared. The addition of N decreases M{sub s} of Ti-Nb-4Zr-2Ta alloys by about 200 K per 1 at.%N and improves the superelastic properties of Ti-Nb-4Zr-2Ta alloys. The dissolution of {alpha} phase increases the martensitic transformation start temperature and decreases the superelastic recovery strain for the N-free alloy, whereas it causes opposite effects for the N-added alloy. The different annealing temperature dependences of superelastic properties are discussed on the basis of microstructure observation.

  8. Effect of nitrogen addition and annealing temperature on superelastic properties of Ti-Nb-Zr-Ta alloys

    International Nuclear Information System (INIS)

    Tahara, Masaki; Kim, Hee Young; Hosoda, Hideki; Nam, Tae-hyun; Miyazaki, Shuichi

    2010-01-01

    Research highlights: In this study, the effects of composition and annealing temperature on microstructure, shape memory effect and superelastic properties were investigated in Ti-Nb-4Zr-2Ta-N alloys by measuring stress-strain curves at various temperatures and using transmission electron microscopy. Dissolution of α phase increases M s and decreases the critical stress for slip for the Ti-22Nb-4Zr-2Ta alloy while it causes the decrease of M s and the increase of the critical stress for slip for the Ti-20Nb-4Zr-2Ta-0.6N alloy. The different effect of dissolution of α phase can be attributed to the fact that N is absorbed in α phase. - Abstract: The composition dependence of the mechanical properties and martensitic transformation behavior of Ti-Nb-4Zr-2Ta-N alloys is investigated. The effect of annealing temperature on the microstructural evolution and superelastic properties in the N-added and N-free alloys is compared. The addition of N decreases M s of Ti-Nb-4Zr-2Ta alloys by about 200 K per 1 at.%N and improves the superelastic properties of Ti-Nb-4Zr-2Ta alloys. The dissolution of α phase increases the martensitic transformation start temperature and decreases the superelastic recovery strain for the N-free alloy, whereas it causes opposite effects for the N-added alloy. The different annealing temperature dependences of superelastic properties are discussed on the basis of microstructure observation.

  9. Thin TiOx layer as a voltage divider layer located at the quasi-Ohmic junction in the Pt/Ta2O5/Ta resistance switching memory.

    Science.gov (United States)

    Li, Xiang Yuan; Shao, Xing Long; Wang, Yi Chuan; Jiang, Hao; Hwang, Cheol Seong; Zhao, Jin Shi

    2017-02-09

    Ta 2 O 5 has been an appealing contender for the resistance switching random access memory (ReRAM). The resistance switching (RS) in this material is induced by the repeated formation and rupture of the conducting filaments (CFs) in the oxide layer, which are accompanied by the almost inevitable randomness of the switching parameters. In this work, a 1 to 2 nm-thick Ti layer was deposited on the 10 nm-thick Ta 2 O 5 RS layer, which greatly improved the RS performances, including the much-improved switching uniformity. The Ti metal layer was naturally oxidized to TiO x (x resistance value was comparable to the on-state resistance of the Ta 2 O 5 RS layer. The series resistor TiO x efficiently suppressed the adverse effects of the voltage (or current) overshooting at the moment of switching by the appropriate voltage partake effect, which increased the controllability of the CF formation and rupture. The switching cycle endurance was increased by two orders of magnitude even during the severe current-voltage sweep tests compared with the samples without the thin TiO x layer. The Ti deposition did not induce any significant overhead to the fabrication process, making the process highly promising for the mass production of a reliable ReRAM.

  10. Overexpression of wheat ferritin gene TaFER-5B enhances tolerance to heat stress and other abiotic stresses associated with the ROS scavenging.

    Science.gov (United States)

    Zang, Xinshan; Geng, Xiaoli; Wang, Fei; Liu, Zhenshan; Zhang, Liyuan; Zhao, Yue; Tian, Xuejun; Ni, Zhongfu; Yao, Yingyin; Xin, Mingming; Hu, Zhaorong; Sun, Qixin; Peng, Huiru

    2017-01-14

    The yield of wheat (Triticum aestivum L.), an important crop, is adversely affected by heat stress in many regions of the world. However, the molecular mechanisms underlying thermotolerance are largely unknown. A novel ferritin gene, TaFER, was identified from our previous heat stress-responsive transcriptome analysis of a heat-tolerant wheat cultivar (TAM107). TaFER was mapped to chromosome 5B and named TaFER-5B. Expression pattern analysis revealed that TaFER-5B was induced by heat, polyethylene glycol (PEG), H 2 O 2 and Fe-ethylenediaminedi(o-hydroxyphenylacetic) acid (Fe-EDDHA). To confirm the function of TaFER-5B in wheat, TaFER-5B was transformed into the wheat cultivar Jimai5265 (JM5265), and the transgenic plants exhibited enhanced thermotolerance. To examine whether the function of ferritin from mono- and dico-species is conserved, TaFER-5B was transformed into Arabidopsis, and overexpression of TaFER-5B functionally complemented the heat stress-sensitive phenotype of a ferritin-lacking mutant of Arabidopsis. Moreover, TaFER-5B is essential for protecting cells against heat stress associated with protecting cells against ROS. In addition, TaFER-5B overexpression also enhanced drought, oxidative and excess iron stress tolerance associated with the ROS scavenging. Finally, TaFER-5B transgenic Arabidopsis and wheat plants exhibited improved leaf iron content. Our results suggest that TaFER-5B plays an important role in enhancing tolerance to heat stress and other abiotic stresses associated with the ROS scavenging.

  11. "Forest Grove School District v. T.A." Supreme Court Case: Implications for School Psychology Practice

    Science.gov (United States)

    Dixon, Shauna G.; Eusebio, Eleazar C.; Turton, William J.; Wright, Peter W. D.; Hale, James B.

    2011-01-01

    The 2009 "Forest Grove School District v. T.A." United States Supreme Court case could have significant implications for school psychology practice. The Court ruled that the parents of a student with a disability were entitled to private school tuition reimbursement even though T.A. had not been identified with a disability or previously…

  12. Tribological Behaviour of Ti:Ta-DLC Films Under Different Tribo-Test Conditions

    Science.gov (United States)

    Efeoglu, İhsan; Keleş, Ayşenur; Totik, Yaşar; Çiçek, Hikmet; Emine Süküroglu, Ebru

    2018-01-01

    Diamond-like carbon (DLC) films are suitable applicants for cutting tools due to their high hardness, low friction coefficient and wear rate. Doping metals in DLC films have been improved its tribological properties. In this study, titanium and tantalum doped hydrogenated DLC films were deposited by closed-field unbalanced magnetron sputtering system onto M2 high speed steels in Ar/N2/C2H2 atmosphere. The friction and wear properties of Ti:Ta-DLC film were investigated under different tribo-test conditions including in atmospheric pressure, distilled water, commercial oil and Ar atmosphere. The coated specimens were characterized by SEM and X-ray diffraction techniques. The bonding state of C-C (sp3) and C=C (sp2) were obtained with XPS. The tribological properties of Ti:Ta-DLC were investigated with pin-on-disc wear test. Hardness measurements performed by micro-indentation. Our results suggest that Ti:Ta-doped DLC film shows very dense columnar microstructure, high hardness (38.2 GPa) with low CoF (µ≈0.02) and high wear resistance (0.5E-6 mm3/Nm).

  13. TA-54 (Area G) Risk Assessment from Extreme Wildfire Scenarios

    Energy Technology Data Exchange (ETDEWEB)

    Linn, Rodman Ray [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Koo, Eunmo [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Honig, Kristen Ann [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); White, Judith [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Funk, David John [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

    2016-08-10

    Los Alamos National Laboratory (LANL) and surrounding areas have been exposed to at least four significant wildfires since 1977 and there have been numerous others within 50 miles of LANL. Based on this history, wildfires are considered a risk to LANL facilities and their contents. While many LANL facilities are at risk to wildfire to some degree, they are found in a wide variety of conditions, thus they have varying sensitivities to wildfires. Additionally, LANL facilities have various functions and different assets, so they have a wide range of values or consequences if compromised. Therefore, determining the risks and precautions that are warranted to mitigate these risks must be done on a case-by-case basis. In an effort to assess possible wildfire risks to sensitive materials stored in a Perma-Con® in dome TA-54-0375, a conventional fire risk analysis was performed. This conventional risk analysis is documented in Engineering Evaluation Form AP-FIRE-001-FM1, which is dated 9/28/2015 and was titled ‘Wildland Fire Exposure Evaluation for Building TA-54-0375’ (Hall 2015). This analysis acknowledged that there was significant chance of wildfire in the vicinity of TA-54-0375, but the amount of combustible material surrounding the building was deemed low. The wildland fuels that were closest to the building were largely fine fuels and were not expected to have significant duration of heat release. The prevailing winds at this location are from the south and southwest and the nearest significant upwind fuels (tree crowns or unmown grasses) are at least 300 feet away. Based on these factors the conventional wildland fire risk to TA-54-0375 was deemed minimal, “Acceptable As Is, No Action Required.” This risk evaluation was based on a combined assessment of low probability of wildfires arriving at the site from other directions (where higher fuel loadings might be present) as well as the effective setback of fuels in the direction that fire is

  14. Synthesis by two methods and crystal structure determination of a new pyrochlore-related compound Sm{sub 2}FeTaO{sub 7}

    Energy Technology Data Exchange (ETDEWEB)

    Torres-Martinez, Leticia M., E-mail: lettorresg@yahoo.com [Departamento de Ecomateriales y Energia, Facultad de Ingenieria Civil, Universidad Autonoma de Nuevo Leon, Cd. Universitaria, San Nicolas de los Garza, Nuevo Leon 66450 (Mexico); Ruiz-Gomez, Miguel A. [Departamento de Ecomateriales y Energia, Facultad de Ingenieria Civil, Universidad Autonoma de Nuevo Leon, Cd. Universitaria, San Nicolas de los Garza, Nuevo Leon 66450 (Mexico); Facultad de Ciencias Quimicas, Universidad Autonoma de San Luis Potosi, Av. Manuel Nava 6, San Luis Potosi, S.L.P. 78290 (Mexico); Figueroa-Torres, M.Z.; Juarez-Ramirez, Isaias [Departamento de Ecomateriales y Energia, Facultad de Ingenieria Civil, Universidad Autonoma de Nuevo Leon, Cd. Universitaria, San Nicolas de los Garza, Nuevo Leon 66450 (Mexico); Moctezuma, Edgar [Facultad de Ciencias Quimicas, Universidad Autonoma de San Luis Potosi, Av. Manuel Nava 6, San Luis Potosi, S.L.P. 78290 (Mexico); and others

    2012-04-16

    Graphical abstract: The monoclinic (space group C2/c) structure of a new compound, Sm{sub 2}FeTaO{sub 7} shows an alternating Sm-O and Fe/Ta-O layers. In the Fe/Ta-O layer, Fe/Ta1 and Fe/Ta3 cations are coordinated by six oxygen atoms, forming irregular octahedral interconnected into a hexagonal tungsten bronze (HTB) type network. The HTB layer is a fundamental framework in the pyrohlore-related structure. Highlights: Black-Right-Pointing-Pointer Pyrochlore-related compound Sm{sub 2}FeTaO{sub 7} prepared by solid state reaction and sol-gel. Black-Right-Pointing-Pointer Sm{sub 2}FeTaO{sub 7} crystallizes with a monoclinic crystal structure and space group C2/c. Black-Right-Pointing-Pointer The compound is synthesized by sol-gel at lower temperature and time than solid state. Black-Right-Pointing-Pointer Surface area of sol-gel Sm{sub 2}FeTaO{sub 7} is 10 times higher than that prepared by solid state. - Abstract: This paper reports on the synthesis of a new pyrochlore-related compound Sm{sub 2}FeTaO{sub 7} by both solid state reaction and sol-gel synthesis routes. Structural features were determined by X-ray powder diffraction and Rietveld refinement and were corroborated using Transmission Electron Microscopy (TEM). The results revealed that Sm{sub 2}FeTaO{sub 7} crystallized in the monoclinic system with space group C2/c and the following cell parameters: a = 13.1307(5) Angstrom-Sign , b = 7.5854(3) Angstrom-Sign , c = 11.6425(4) Angstrom-Sign and {beta} = 100.971(2) Degree-Sign . The monoclinic structure of Sm{sub 2}FeTaO{sub 7} showed an arrangement of alternating Sm-O and Fe/Ta-O layers and two types of irregular octahedra of Fe/Ta-O, which are interconnected into a hexagonal tungsten bronze (HTB)-type network. On the other hand, Sm{sub 2}FeTaO{sub 7} prepared by sol-gel was obtained with lower particle sizes than the solid state produced compound. The difference in particle size causes a difference of one order of magnitude in the specific surface area. In

  15. Czech Verse Processing System KVĚTA: Phonetic and Metrical Components

    Czech Academy of Sciences Publication Activity Database

    Plecháč, Petr

    2016-01-01

    Roč. 7, č. 2 (2016), s. 159-174 ISSN 1337-7892 Institutional support: RVO:68378068 Keywords : Verse Processing * KVĚTA * Czech language * phonetic and metrical annotation Subject RIV: AJ - Letters, Mass-media, Audiovision

  16. Thickness effect of ultra-thin Ta2O5 resistance switching layer in 28 nm-diameter memory cell

    Science.gov (United States)

    Park, Tae Hyung; Song, Seul Ji; Kim, Hae Jin; Kim, Soo Gil; Chung, Suock; Kim, Beom Yong; Lee, Kee Jeung; Kim, Kyung Min; Choi, Byung Joon; Hwang, Cheol Seong

    2015-11-01

    Resistance switching (RS) devices with ultra-thin Ta2O5 switching layer (0.5-2.0 nm) with a cell diameter of 28 nm were fabricated. The performance of the devices was tested by voltage-driven current—voltage (I-V) sweep and closed-loop pulse switching (CLPS) tests. A Ta layer was placed beneath the Ta2O5 switching layer to act as an oxygen vacancy reservoir. The device with the smallest Ta2O5 thickness (0.5 nm) showed normal switching properties with gradual change in resistance in I-V sweep or CLPS and high reliability. By contrast, other devices with higher Ta2O5 thickness (1.0-2.0 nm) showed abrupt switching with several abnormal behaviours, degraded resistance distribution, especially in high resistance state, and much lower reliability performance. A single conical or hour-glass shaped double conical conducting filament shape was conceived to explain these behavioural differences that depended on the Ta2O5 switching layer thickness. Loss of oxygen via lateral diffusion to the encapsulating Si3N4/SiO2 layer was suggested as the main degradation mechanism for reliability, and a method to improve reliability was also proposed.

  17. Microsolvation effect and hydrogen-bonding pattern of taurine-water TA-(H2O)n (n = 1-3) complexes.

    Science.gov (United States)

    Dai, Yumei; Wang, Yuhua; Huang, Zhengguo; Wang, Hongke; Yu, Lei

    2012-01-01

    The microsolvation of taurine (TA) with one, two or three water molecules was investigated by a density functional theory (DFT) approach. Quantum theory of atoms in molecules (QTAIM) analyses were employed to elucidate the hydrogen bond (H-bond) interaction characteristics in TA-(H(2)O)(n) (n = 1-3) complexes. The results showed that the intramolecular H-bond formed between the hydroxyl and the N atom of TA are retained in most TA-(H(2)O)(n) (n = 1-3) complexes, and are strengthened via cooperative effects among multiple H-bonds from n = 1-3. A trend of proton transformation exists from the hydroxyl to the N atom, which finally results in the cleavage of the origin intramolecular H-bond and the formation of a new intramolecular H-bond between the amino and the O atom of TA. Therefore, the most stable TA-(H(2)O)(3) complex becomes a zwitterionic complex rather than a neutral type. A many-body interaction analysis showed that the major contributors to the binding energies for complexes are the two-body energies, while three-body energies and relaxation energies make significant contributions to the binding energies for some complexes, whereas the four-body energies are too small to be significant.

  18. Enhanced oxygen vacancy diffusion in Ta2O5 resistive memory devices due to infinitely adaptive crystal structure

    Science.gov (United States)

    Jiang, Hao; Stewart, Derek A.

    2016-04-01

    Metal oxide resistive memory devices based on Ta2O5 have demonstrated high switching speed, long endurance, and low set voltage. However, the physical origin of this improved performance is still unclear. Ta2O5 is an important archetype of a class of materials that possess an adaptive crystal structure that can respond easily to the presence of defects. Using first principles nudged elastic band calculations, we show that this adaptive crystal structure leads to low energy barriers for in-plane diffusion of oxygen vacancies in λ phase Ta2O5. Identified diffusion paths are associated with collective motion of neighboring atoms. The overall vacancy diffusion is anisotropic with higher diffusion barriers found for oxygen vacancy movement between Ta-O planes. Coupled with the fact that oxygen vacancy formation energy in Ta2O5 is relatively small, our calculated low diffusion barriers can help explain the low set voltage in Ta2O5 based resistive memory devices. Our work shows that other oxides with adaptive crystal structures could serve as potential candidates for resistive random access memory devices. We also discuss some general characteristics for ideal resistive RAM oxides that could be used in future computational material searches.

  19. Overexpression of wheat lipid transfer protein gene TaLTP5 increases resistances to Cochliobolus sativus and Fusarium graminearum in transgenic wheat.

    Science.gov (United States)

    Zhu, Xiuliang; Li, Zhao; Xu, Huijun; Zhou, Miaoping; Du, Lipu; Zhang, Zengyan

    2012-08-01

    The fungus Cochliobolus sativus is the main pathogen of common root rot, a serious soil-borne disease of wheat (Triticum aestivum L.). The fungus Fusarium graminearum is the primary pathogen of Fusarium head blight, a devastating disease of wheat worldwide. In this study, the wheat lipid transfer protein gene, TaLTP5, was cloned and evaluated for its ability to suppress disease development in transgenic wheat. TaLTP5 expression was induced after C. sativus infection. The TaLTP5 expression vector, pA25-TaLTP5, was constructed and bombarded into Chinese wheat variety Yangmai 18. Six TaLTP5 transgenic wheat lines were established and characterized. PCR and Southern blot analyses indicated that the introduced TaLTP5 gene was integrated into the genomes of six transgenic wheat lines by distinct patterns, and heritable. RT-PCR and real-time quantitative RT-PCR revealed that the TaLTP5 gene was over-expressed in the transgenic wheat lines compared to segregants lacking the transgene and wild-type wheat plants. Following challenge with C. sativus or F. graminearum, all six transgenic lines overexpressing TaLTP5 exhibited significantly enhanced resistance to both common root rot and Fusarium head blight compared to the untransformed wheat Yangmai 18.

  20. Stability of Ta-encapsulating Si clusters on Si(111)-(7x7) surfaces

    CERN Document Server

    Uchida, N; Miyazaki, T; Kanayama, T

    2003-01-01

    Tantalum containing Si cluster ions TaSi sub 1 sub 0 sub - sub 1 sub 3 H sub x sup + were synthesized in an ion trap and deposited onto Si(111)-(7x7) surfaces with a kinetic energy of 18 eV. Scanning tunnelling microscope observations revealed that the clusters adsorbed on the surface without decomposition, consistent with ab initio calculation results, that predicted the clusters would have stable Si-cage structures with a Ta atom at the centre. (rapid communication)

  1. Aging of oxygen and hydrogen plasma discharge treated a-C:H and ta-C coatings

    Energy Technology Data Exchange (ETDEWEB)

    Bachmann, Svenja [Physics of Surfaces, Institute of Materials Science, Technische Universität Darmstadt, Alarich-Weiss-Str. 16, 64287 Darmstadt (Germany); BMW Group, Hufelandstraße 4, 80788 Munich (Germany); Schulze, Marcus [Physics of Surfaces, Institute of Materials Science, Technische Universität Darmstadt, Alarich-Weiss-Str. 16, 64287 Darmstadt (Germany); Center of Smart Interfaces, Technische Universität Darmstadt, Alarich-Weiss-Str. 10, 64287 Darmstadt (Germany); Morasch, Jan [Institute of Materials Science, Technische Universität Darmstadt, Surface Science Division, Jovanka-Bonschits-Straße 2, 64287 Darmstadt (Germany); Hesse, Sabine [Physics of Surfaces, Institute of Materials Science, Technische Universität Darmstadt, Alarich-Weiss-Str. 16, 64287 Darmstadt (Germany); Center of Smart Interfaces, Technische Universität Darmstadt, Alarich-Weiss-Str. 10, 64287 Darmstadt (Germany); Hussein, Laith [Eduard-Zintl-Institut, Department of Chemistry, Technische Universität Darmstadt, Alarich-Weiss-Str. 12, 64287, Darmstadt (Germany); Krell, Lisa; Schnagl, Johann [BMW Group, Hufelandstraße 4, 80788 Munich (Germany); Stark, Robert W. [Physics of Surfaces, Institute of Materials Science, Technische Universität Darmstadt, Alarich-Weiss-Str. 16, 64287 Darmstadt (Germany); Center of Smart Interfaces, Technische Universität Darmstadt, Alarich-Weiss-Str. 10, 64287 Darmstadt (Germany); and others

    2016-05-15

    Highlights: • The water CA of O{sub 2} and H{sub 2} plasma treated a-C:H and ta-C changes from hydrophillic to hydrophobic on aging. • XPS study indicates that the decrease in surface energy of plasma treated a-C:H and ta-C could be due to adsorption of organic component from air. • The COFLFM of O{sub 2} and H{sub 2} plasma treated a-C:H and ta-C decreased upon aging. • The COF of glycerol lubricated ta-C showed no sign of change upon aging. - Abstract: Surface modification with gas plasma is an efficient and easy way to improve the surface energy and the tribological behavior of diamond-like carbon (DLC) coatings, e.g., in biomedical implants or as protective coatings. However, the long-term performance of the plasma treated DLC coatings is not fully clear. We thus studied the long-term stability of two kinds of DLC coatings, namely (a) hydrogenated amorphous carbon (a-C:H) and (b) tetrahedral amorphous carbon (ta-C) treated at different radio frequency (RF) power and time of oxygen (O{sub 2}) and hydrogen (H{sub 2}) plasma. Their surface properties, e.g. surface wettability, structure and tribological behavior, were studied at regular intervals for a period of two months using contact angle goniometer, Raman spectroscopy, X-ray photoelectron spectroscopy (XPS), lateral force microscopy (LFM) and ball on disc apparatus. The surface energy of both the coatings decreased upon aging. The higher the RF power and time of treatment, the higher was the hydrophobicity upon aging. XPS analysis showed that the increase in hydrophobicity could be due to adsorption of unavoidable volatile organic components in the atmosphere. The H{sub 2} plasma treated ta-C was capable of rearranging its structural bonds upon aging. The nano-friction measurements by LFM showed that the coefficient of friction of plasma treated a-C:H and ta-C decreased upon aging. The results indicate that the surface properties of plasma treated a‐C:H and ta‐C are not stable on long-term and are

  2. Total neutron cross section for 181Ta

    Directory of Open Access Journals (Sweden)

    Schilling K.-D.

    2010-10-01

    Full Text Available The neutron time of flight facility nELBE, produces fast neutrons in the energy range from 0.1 MeV to 10 MeV by impinging a pulsed relativistic electron beam on a liquid lead circuit [1]. The short beam pulses (∼10 ps and a small radiator volume give an energy resolution better than 1% at 1 MeV using a short flight path of about 6 m, for neutron TOF measurements. The present neutron source provides 2 ⋅ 104  n/cm2s at the target position using an electron charge of 77 pC and 100 kHz pulse repetition rate. This neutron intensity enables to measure neutron total cross section with a 2%–5% statistical uncertainty within a few days. In February 2008, neutron radiator, plastic detector [2] and data acquisition system were tested by measurements of the neutron total cross section for 181Ta and 27Al. Measurement of 181Ta was chosen because lack of high quality data in an anergy region below 700 keV. The total neutron cross – section for 27Al was measured as a control target, since there exists data for 27Al with high resolution and low statistical error [3].

  3. Photocatalytic hydrogen production using visible-light-responsive Ta 3N5 photocatalyst supported on monodisperse spherical SiO2 particulates

    KAUST Repository

    Liu, Xiaoming

    2014-01-01

    Fine nanoparticles of Ta3N5 (10-20 nm) were synthesized on the surfaces of SiO2 spheres with a diameter of ∼550 nm. A sol-gel method was used to modify the surface of SiO2 with Ta2O5 from TaCl5 dissolved in ethanol in the presence of citric acid and polyethylene glycol. The resulting oxide composites were treated in an NH3 flow at 1123 K to form core-shell structured Ta3N5/SiO2 sub-microspheres. The obtained samples were characterized using powder X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FT-IR), field emission scanning electron microscopy (FESEM), energy-dispersive X-ray spectra (EDX), transmission electron microscopy (TEM), and photocatalytic activity measurements for H 2 evolution from an aqueous methanol solution. The XRD results demonstrate the expected sequential formation of Ta2O5 layers, followed by Ta3N5 after nitridation on the Ta 2O5/SiO2 composite. SEM and TEM observations indicate that the obtained Ta3N5/SiO2 sub-microspheres have a uniform size distribution with high crystallinity and an obvious core-shell structure. The presence of support maintained the intrinsic photocatalytic activity of Ta3N5 nanoparticles, but it did drastically improve the dispersion of the photocatalysts in the solution. This study proposes the use of an inert support in photocatalytic reactors to improve ease of handling the powder photocatalyst for gas-phase photocatalysis and the suspension of the solution, controlling nature of light harvesting and degree of scattering of the photoreactor. © 2013 Elsevier Ltd. All rights reserved.

  4. Study on mechanical properties and metallograph of high density function alloy Ta-12W

    International Nuclear Information System (INIS)

    Liu Taiping; Huang Zhenchi

    1998-12-01

    As a new material, the study on the metallograph and properties of Ta-12W alloy has been set about to testify its employ characteristics. The alloy's metallograph specimen preparation methods to illustrate microstructure are found out, 12 dose of chemical-corrosives are given. The author studies the metallograph, weld structure and properties, and chemical-corrosive resistance, provides scientific base for future research on Ta-12 W alloy

  5. Ta1, a novel 105 KD human T cell activation antigen defined by a monoclonal antibody.

    Science.gov (United States)

    Fox, D A; Hussey, R E; Fitzgerald, K A; Acuto, O; Poole, C; Palley, L; Daley, J F; Schlossman, S F; Reinherz, E L

    1984-09-01

    By using a murine monoclonal antibody produced against an IL 2-dependent human T cell line, we defined a T lineage-specific molecule, termed Ta1, that is expressed strongly on activated T lymphocytes of both the T4 and T8 subsets, as well as on T cell lines and clones, but only weakly on a fraction of resting T cells. SDS-PAGE analysis of immunoprecipitates from 125I-labeled, activated T cells demonstrates a single major band of apparent m.w. 105 KD under both reducing and nonreducing conditions. Unlike anti-IL 2 receptor antibodies, anti-Ta1 does not inhibit T cell proliferative responses to mitogen, antigen, or IL 2-containing medium. Moreover, anti-Ta1 has no effect on T cell-mediated cytotoxicity. Ta1 appears to be a novel human T cell-specific activation antigen that may serve as a useful marker of T cell activation in human disease.

  6. Quantitative Proteomics of the Root of Transgenic Wheat Expressing TaBWPR-1.2 Genes in Response to Waterlogging

    Directory of Open Access Journals (Sweden)

    Emdadul Haque

    2014-11-01

    Full Text Available Once candidate genes are available, the application of genetic transformation plays a major part to study their function in plants for adaptation to respective environmental stresses, including waterlogging (WL. The introduction of stress-inducible genes into wheat remains difficult because of low transformation and plant regeneration efficiencies and expression variability and instability. Earlier, we found two cDNAs encoding WL stress-responsive wheat pathogenesis-related proteins 1.2 (TaBWPR-1.2, TaBWPR-1.2#2 and TaBWPR-1.2#13. Using microprojectile bombardment, both cDNAs were introduced into “Bobwhite”. Despite low transformation efficiency, four independent T2 homozygous lines for each gene were isolated, where transgenes were ubiquitously and variously expressed. The highest transgene expression was obtained in Ubi:TaBWPR-1.2#2 L#11a and Ubi:TaBWPR-1.2#13 L#4a. Using quantitative proteomics, the root proteins of L#11a were analyzed to explore possible physiological pathways regulated by TaBWPR-1.2 under normal and waterlogged conditions. In L#11a, the abundance of proteasome subunit alpha type-3 decreased under normal conditions, whereas that of ferredoxin precursor and elongation factor-2 increased under waterlogged conditions in comparison with normal plants. Proteomic results suggest that L#11a is one of the engineered wheat plants where TaBWPR-1.2#2 is most probably involved in proteolysis, protein synthesis and alteration in the energy pathway in root tissues via the above proteins in order to gain metabolic adjustment to WL.

  7. Lithium-ion storage capacitors achieved by CVD graphene/TaC/Ta-wires and carbon hollow spheres

    International Nuclear Information System (INIS)

    Zhao, Liwei; Li, Hongji; Li, Mingji; Xu, Sheng; Li, Cuiping; Qu, Changqing; Zhang, Lijun; Yang, Baohe

    2016-01-01

    Highlights: • Graphene/TaC/Ta wire electrode was prepared by CVD. • Carbon hollow spheres as a solid electrolyte were prepared by hydrothermal. • Specific capacitance of assembled capacitor reached 593 F g −1 at 10 A g −1 . • The capacitor provided high energy and power densities (132 W h kg −1 /3.17 kW kg −1 ). • The hybrid capacitor also exhibited a high stability during long endurance tests. - Abstract: Lithium-ion storage capacitors were assembled using graphene/tantalum carbide/tantalum wire electrodes and carbon hollow spheres as electrolyte. The graphene/tantalum carbide layers were prepared by electron-assisted hot filament chemical vapor deposition; the carbon hollow spheres were synthesized by hydrothermal reaction and pyrolysis treatment. The specific capacitance of the capacitor was 593 F g −1 at a current density of 10 A g −1 . The capacitor showed excellent cycling stability, retaining 91.2% of its initial capacitance after 8000 cycles. Moreover, the capacitor provided a high specific energy density of 132 W h kg −1 at a high power density of 3.17 kW kg −1 . The high energy density is attributed to the widened operation window ranging from 0 to 3.0 V. The graphene layer of the electrode and carbon hollow spheres in electrolyte synergistic affect influence on the electrochemical performance of the capacitor are discussed. In addition, the use of a low-cost lithium salt, lithium chloride, is also featured in this paper.

  8. NMR structure of temporin-1 ta in lipopolysaccharide micelles: mechanistic insight into inactivation by outer membrane.

    Directory of Open Access Journals (Sweden)

    Rathi Saravanan

    Full Text Available BACKGROUND: Antimicrobial peptides (AMPs play important roles in the innate defense mechanism. The broad spectrum of activity of AMPs requires an efficient permeabilization of the bacterial outer and inner membranes. The outer leaflet of the outer membrane of Gram negative bacteria is made of a specialized lipid called lipopolysaccharide (LPS. The LPS layer is an efficient permeability barrier against anti-bacterial agents including AMPs. As a mode of protection, LPS can induce self associations of AMPs rendering them inactive. Temporins are a group of short-sized AMPs isolated from frog skin, and many of them are inactive against Gram negative bacteria as a result of their self-association in the LPS-outer membrane. PRINCIPAL FINDINGS: Using NMR spectroscopy, we have determined atomic resolution structure and characterized localization of temporin-1Ta or TA (FLPLIGRVLSGIL-amide in LPS micelles. In LPS micelles, TA adopts helical conformation for residues L4-I12, while residues F1-L3 are found to be in extended conformations. The aromatic sidechain of residue F1 is involved in extensive packing interactions with the sidechains of residues P3, L4 and I5. Interestingly, a number of long-range NOE contacts have been detected between the N-terminal residues F1, P3 with the C-terminal residues S10, I12, L13 of TA in LPS micelles. Saturation transfer difference (STD NMR studies demonstrate close proximity of residues including F1, L2, P3, R7, S10 and L13 with the LPS micelles. Notably, the LPS bound structure of TA shows differences with the structures of TA determined in DPC and SDS detergent micelles. SIGNIFICANCE: We propose that TA, in LPS lipids, forms helical oligomeric structures employing N- and C-termini residues. Such oligomeric structures may not be translocated across the outer membrane; resulting in the inactivation of the AMP. Importantly, the results of our studies will be useful for the development of antimicrobial agents with a

  9. Influence of Ta Content in High Purity Niobium on Cavity Performance Preliminary Results*

    CERN Document Server

    Kneisel, P

    2004-01-01

    In a previous paper* a program designed to study the influence of the residual tantalum content on the superconducting properties of pure niobium metal for RF cavities was outlined. The main rationale for this program was based on a potential cost reduction for high purity niobium, if a less strict limit on the chemical specification for Ta content, which is not significantly affecting the RRR–value, could be tolerated for high performance cavities. Four ingots with different Ta contents have been melted and transformed into sheets. In each manufacturing step the quality of the material has been monitored by employing chemical analysis, neutron activation analysis, thermal conductivity measurements and evaluation of the mechanical properties. The niobium sheets have been scanned for defects by an eddy current device. From three of the four ingots—Ta contents 100, 600 and 1,200 wppm—two single cell cavities each of the CEBAF variety have been fabricated and a series of tests on each ...

  10. Measurements of quadrupolar interaction by perturbed angular correltion method on intercalated 2H-TaS sub(2)

    International Nuclear Information System (INIS)

    Saitovitch, H.

    1979-01-01

    This work is based on our quadrupolar interaction (QI) measurements on intercalated 2H-TaS sub(2) coumponds. As intercalating elements we used the alcalines - Li, Na, K, Cs -as well as the NH sub(3) (ammonia) and C sub(6) H sub(5) N (pyridine) molecules. The (QI) measurements were performed via the differential perturbed angular correlation (DPAC) technique, using Ta sup(181) as the probe isotope, on the hydrated and anhidrous phases of the intercalated systems. Our results happened to be in better agreement with the ionic model, one of the accepted models used to describe the intercalation process, as well as the transfered charges quantities and its distribution in the intercalated systems. And by its side the measured quantities, quadrupole interaction frequencies (QIF) and their distributions δ, contributed to support and to improve the ionic model. A strong charge dynamics between the 2H-TaS sub(2) sandwiches was observed and a relation between the (QIF) changes and amount of transfered charge (e sup(-)/Ta) was established. The attempt to specify the numerical contributions to the (QI) changes arriving from the different components of the 2H-TaS sub(2) intercalated systems put in evidence the probable orbitals involved in the systems bonds. Finally the kinetics of the intercalation process to form the 2H-TaS sub(2) (Li) sub(x) system was followed continuously by the (DPAC) measurements. (author)

  11. Adjustments of the TaD electron density reconstruction model with GNSS-TEC parameters for operational application purposes

    Directory of Open Access Journals (Sweden)

    Belehaki Anna

    2012-12-01

    Full Text Available Validation results on the latest version of TaD model (TaDv2 show realistic reconstruction of the electron density profiles (EDPs with an average error of 3 TECU, similar to the error obtained from GNSS-TEC calculated paremeters. The work presented here has the aim to further improve the accuracy of the TaD topside reconstruction, adjusting the TEC parameter calculated from TaD model with the TEC parameter calculated by GNSS transmitting RINEX files provided by receivers co-located with the Digisondes. The performance of the new version is tested during a storm period demonstrating further improvements in respect to the previous version. Statistical comparison of modeled and observed TEC confirms the validity of the proposed adjustment. A significant benefit of the proposed upgrade is that it facilitates the real-time implementation of TaD. The model needs a reliable measure of the scale height at the peak height, which is supposed to be provided by Digisondes. Oftenly, the automatic scaling software fails to correctly calculate the scale height at the peak, Hm, due to interferences in the receiving signal. Consequently the model estimated topside scale height is wrongly calculated leading to unrealistic results for the modeled EDP. The proposed TEC adjustment forces the model to correctly reproduce the topside scale height, despite the inaccurate values of Hm. This adjustment is very important for the application of TaD in an operational environment.

  12. Anti-biofouling function of amorphous nano-Ta2O5 coating for VO2-based intelligent windows

    Science.gov (United States)

    Li, Jinhua; Guo, Geyong; Wang, Jiaxing; Zhou, Huaijuan; Shen, Hao; Yeung, Kelvin W. K.

    2017-04-01

    From environmental and health perspectives, the acquisition of a surface anti-biofouling property holds important significance for the usability of VO2 intelligent windows. Herein, we firstly deposited amorphous Ta2O5 nanoparticles on VO2 film by the magnetron sputtering method. It was found that the amorphous nano-Ta2O5 coating possessed a favorable anti-biofouling capability against Pseudomonas aeruginosa as an environmental microorganism model, behind which lay the mechanism that the amorphous nano-Ta2O5 could interrupt the microbial membrane electron transport chain and significantly elevate the intracellular reactive oxygen species (ROS) level. A plausible relationship was established between the anti-biofouling activity and physicochemical nature of amorphous Ta2O5 nanoparticles from the perspective of defect chemistry. ROS-induced oxidative damage gave rise to microbial viability loss. In addition, the amorphous nano-Ta2O5 coating can endow VO2 with favorable cytocompatibility with human skin fibroblasts. This study may provide new insights into understanding the anti-biofouling and antimicrobial actions of amorphous transition metal oxide nanoparticles, which is conducive to expanding their potential applications in environmental fields.

  13. Tuning the size-dependent He-irradiated tolerance and strengthening behavior of crystalline/amorphous Cu/Ta nanostructured multilayers

    Energy Technology Data Exchange (ETDEWEB)

    Liang, X.Q.; Zhang, J.Y., E-mail: jinyuzhang1002@mail.xjtu.edu.cn; Wang, Y.Q.; Wu, S.H.; Zeng, F.; Wu, K.; Liu, G., E-mail: lgsammer@mail.xjtu.edu.cn; Zhang, G.J.; Sun, J.

    2016-08-30

    Nanoindentation methodology was used to measure the hardness of Cu/Ta crystalline/amorphous nanostructured multilayers (CANMs) before and after He ion-implantation at room temperature. These CANMs have a constant modulation period (λ=25 nm) but different modulation ratios (η=h{sub Ta} / h{sub Cu}) spanning from 0.11 to 1.0. It is found that in sharp contrast to previously reported Cu/Cu-Zr CANMs by Zhang et al. [9], the He-irradiated Cu/Ta samples exhibit much greater microstructure stability without radiation-induced devitrification (RID) of glassy Ta nanolayers at smaller η (except the sample at η=1.0). Both the as-deposited and irradiated Cu/Ta CANMs manifest the monotonically increased hardness with decreasing η, however, there is an unexpected transition from size-dependent irradiation hardening at η<1.0 to softening at η≥1.0 caused by a competition between dislocation-bubble interactions in crystalline nanolayers and RID in glassy nanolayers. These findings not only provide fundamental understanding of the radiation-induced defect effect on plastic characteristics of CANMs, but also offer guidance for their microstructure sensitive design for performance optimization at a critical modulation ratio under extreme conditions.

  14. Stormwater Pollution Prevention Plan - TA-60 Asphalt Batch Plant

    Energy Technology Data Exchange (ETDEWEB)

    Sandoval, Leonard Frank [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

    2018-01-31

    This Storm Water Pollution Prevention Plan (SWPPP) was developed in accordance with the provisions of the Clean Water Act (33 U.S.C. §§1251 et seq., as amended), and the Multi-Sector General Permit for Storm Water Discharges Associated with Industrial Activity (U.S. EPA, June 2015) issued by the U.S. Environmental Protection Agency (EPA) for the National Pollutant Discharge Elimination System (NPDES) and using the industry specific permit requirements for Sector P-Land Transportation and Warehousing as a guide. This SWPPP applies to discharges of stormwater from the operational areas of the TA-60-01 Asphalt Batch Plant at Los Alamos National Laboratory. Los Alamos National Laboratory (also referred to as LANL or the “Laboratory”) is owned by the Department of Energy (DOE), and is operated by Los Alamos National Security, LLC (LANS). Throughout this document, the term “facility” refers to the TA-60 Asphalt Batch Plant and associated areas. The current permit expires at midnight on June 4, 2020.

  15. Stormwater Pollution Prevention Plan - TA-60 Material Recycling Facility

    Energy Technology Data Exchange (ETDEWEB)

    Sandoval, Leonard Frank [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

    2018-01-31

    This Storm Water Pollution Prevention Plan (SWPPP) was developed in accordance with the provisions of the Clean Water Act (33 U.S.C. §§1251 et seq., as amended), and the Multi-Sector General Permit for Storm Water Discharges Associated with Industrial Activity (U.S. EPA, June 2015) issued by the U.S. Environmental Protection Agency (EPA) for the National Pollutant Discharge Elimination System (NPDES) and using the industry specific permit requirements for Sector P-Land Transportation and Warehousing as a guide. This SWPPP applies to discharges of stormwater from the operational areas of the TA- 60 Material Recycling Facility at Los Alamos National Laboratory. Los Alamos National Laboratory (also referred to as LANL or the “Laboratory”) is owned by the Department of Energy (DOE), and is operated by Los Alamos National Security, LLC (LANS). Throughout this document, the term “facility” refers to the TA-60 Material Recycling Facility. The current permit expires at midnight on June 4, 2020.

  16. Interplay between lattice distortions, vibrations and phase stability in NbMoTaW high entropy alloys

    NARCIS (Netherlands)

    Kormann, F.H.W.; Sluiter, M.H.F.

    2016-01-01

    Refractory high entropy alloys (HEA), such as BCC NbMoTaW, represent a promising materials class for next-generation high-temperature applications, due to their extraordinary mechanical properties. A characteristic feature of HEAs is the formation of single-phase solid solutions. For BCC NbMoTaW,

  17. Over-expression of TaMYB33 encoding a novel wheat MYB transcription factor increases salt and drought tolerance in Arabidopsis.

    Science.gov (United States)

    Qin, Yuxiang; Wang, Mengcheng; Tian, Yanchen; He, Wenxing; Han, Lu; Xia, Guangmin

    2012-06-01

    Salt and drought stresses often adversely affect plant growth and productivity, MYB transcription factors have been shown to participate in the response to these stresses. Here we identified a new R2R3-type MYB transcription factor gene TaMYB33 from wheat (Triticum aestivum). TaMYB33 was induced by NaCl, PEG and ABA treatments, and its promoter sequence contains putative ABRE, MYB and other abiotic stress related cis-elements. Ectopic over-expression of TaMYB33 in Arabidopsis thaliana remarkably enhanced its tolerance to drought and NaCl stresses, but not to LiCl and KCl treatments. The expressions of AtP5CS and AtZAT12 which mirror the activities of proline and ascorbate peroxidase synthesis respectively were induced in TaMYB33 over-expression lines, indicating TaMYB33 promotes the ability for osmotic pressure balance-reconstruction and reactive oxidative species (ROS) scavenging. The up-regulation of AtAAO3 along with down-regulation of AtABF3, AtABI1 in TaMYB33 over-expression lines indicated that ABA synthesis was elevated while its signaling was restricted. These results suggest that TaMYB33 enhances salt and drought tolerance partially through superior ability for osmotic balance reconstruction and ROS detoxification.

  18. A highly uniform ZnO/NaTaO{sub 3} nanocomposite: Enhanced self-sensitized degradation of colored pollutants under visible light

    Energy Technology Data Exchange (ETDEWEB)

    Xing, Guanjie; Tang, Changhe [School of Chemistry and Chemical Engineering, Inner Mongolia University, Hohhot, Inner Mongolia, 010021 (China); Zhang, Bo [College of Chemistry and Molecular Sciences, Wuhan University, Wuhan, Hubei, 430072 (China); Zhao, Lanxiao; Su, Yiguo [School of Chemistry and Chemical Engineering, Inner Mongolia University, Hohhot, Inner Mongolia, 010021 (China); Wang, Xiaojing, E-mail: wang_xiao_jing@hotmail.com [School of Chemistry and Chemical Engineering, Inner Mongolia University, Hohhot, Inner Mongolia, 010021 (China)

    2015-10-25

    In this study, a highly uniform ZnO/NaTaO{sub 3} composite was prepared via simple hydrothermal synthesis. XRD confirmed the composite was constructed by pure cubic phase of NaTaO{sub 3} and hexagonal phase of ZnO. SEM analysis showed that as-prepared ZnO/NaTaO{sub 3} shaped as an irregular ginger with an obviously smaller size than that of pure ZnO without obvious agglomeration. EDS mapping demonstrated that the four elements (Na, Ta, O, Zn) in the composite were very uniformly distributed. The photocatalytic behaviors of as-prepared composites were studied in the degradation of methylene blue both under UV and visible irradiation. The bare ZnO showed the highest activity with 99.8% methylene blue (MB) photodegraded in 70 min under UV light irradiation whereas 94% photodegraded rate was achieved for ZnO/NaTaO{sub 3}. More importantly, the uniform composite of ZnO/NaTaO{sub 3} exhibited effective degradation of methylene blue under visible light which can be attributed to the well dyes adsorption abilities and the high efficiency of electron separation, induced by the synergistic effect between ZnO and NaTaO{sub 3}. It is confirmed the dye rather than a semiconductor is excited under visible light irradiation and a self-sensitized photocatalytic mechanism was then proposed based on the experimental results. - Graphical abstract: Visible light photocatalytic activity of ZnO/NaTaO{sub 3} and proposed schematic of self-sensitization directed photogradation of MB. - Highlights: • Highly uniform ZnO/NaTaO{sub 3} photocatalysts were fabricated by hydrothermal method. • ZnO/NaTaO{sub 3} composite exhibited effective degradation of MB under visible light. • ZnO/NaTaO{sub 3} composite effectively promoted dye adsorption and electrons separation. • A self-sensitized photocatalytic mechanism was proposed for the degradation of dye.

  19. Density functional theory investigation of elastic properties and martensitic transformation of Ti-Ta alloys

    Energy Technology Data Exchange (ETDEWEB)

    Chakraborty, Tanmoy; Rogal, Jutta; Drautz, Ralf [Interdisciplinary Centre for Advanced Materials Simulation, Ruhr- Universitaet Bochum (Germany)

    2016-07-01

    Ti-Ta alloys are considered as promising materials for high temperature shape memory alloys as well as biomedical applications. The properties of these alloys have been shown to be strongly composition dependent. The temperature for the martensitic transformation between the high temperature cubic austenite and the low temperature orthorhombic martensite decreases linearly with increasing Ta content. Likewise, the elastic properties show clear trends with changing composition. We use density functional theory to investigate the involved phases in Ti-Ta where the disordered phases are treated by special quasi-random structures. To compare the stability of the involved phases as a function of temperature we calculate free energies using the quasi-harmonic Debye model. The obtained trends in the stability are consistent with experimentally measured transformation temperatures. Furthermore, we determine elastic properties which are in good agreement with experimentally observed trends.

  20. Photoluminescent properties of Pr3+ doped YTiAO6 (A= Nb&Ta) euxenite compounds

    Science.gov (United States)

    Venugopal, Meenu; Kumar, H. Padma

    2018-04-01

    Pr3+ doped YTiAO6 (A = Nb and Ta) compounds were prepared by conventional solid state ceramic route. X - ray diffraction studies of the samples confirmed the euxenite orthorhombic phase formation. Effect of Pr3+ doping on the optical and luminescence properties of YTiAO6 (A = Nb and Ta) were studied. The strong absorption in the UV region are due to the absorption by the host YTiAO6 (A = Nb and Ta) and all other peaks can be attributed to that of Pr3+. Host emission peaks are observed around 485 nm and 460 nm in all samples. The red emission observed at 614 nm in the doped samples corresponds to the 1D2 to 3H4 transition of Pr3+ ion. CIE colour coordinates and chromaticity values were also discussed.

  1. The wheat NB-LRR gene TaRCR1 is required for host defence response to the necrotrophic fungal pathogen Rhizoctonia cerealis.

    Science.gov (United States)

    Zhu, Xiuliang; Lu, Chungui; Du, Lipu; Ye, Xingguo; Liu, Xin; Coules, Anne; Zhang, Zengyan

    2017-06-01

    The necrotrophic fungus Rhizoctonia cerealis is the major pathogen causing sharp eyespot disease in wheat (Triticum aestivum). Nucleotide-binding leucine-rich repeat (NB-LRR) proteins often mediate plant disease resistance to biotrophic pathogens. Little is known about the role of NB-LRR genes involved in wheat response to R. cerealis. In this study, a wheat NB-LRR gene, named TaRCR1, was identified in response to R. cerealis infection using Artificial Neural Network analysis based on comparative transcriptomics and its defence role was characterized. The transcriptional level of TaRCR1 was enhanced after R. cerealis inoculation and associated with the resistance level of wheat. TaRCR1 was located on wheat chromosome 3BS and encoded an NB-LRR protein that was consisting of a coiled-coil domain, an NB-ARC domain and 13 imperfect leucine-rich repeats. TaRCR1 was localized in both the cytoplasm and the nucleus. Silencing of TaRCR1 impaired wheat resistance to R. cerealis, whereas TaRCR1 overexpression significantly increased the resistance in transgenic wheat. TaRCR1 regulated certain reactive oxygen species (ROS)-scavenging and production, and defence-related genes, and peroxidase activity. Furthermore, H 2 O 2 pretreatment for 12-h elevated expression levels of TaRCR1 and the above defence-related genes, whereas treatment with a peroxidase inhibitor for 12 h reduced the resistance of TaRCR1-overexpressing transgenic plants and expression levels of these defence-related genes. Taken together, TaRCR1 positively contributes to defence response to R. cerealis through maintaining ROS homoeostasis and regulating the expression of defence-related genes. © 2016 The Authors. Plant Biotechnology Journal published by Society for Experimental Biology and The Association of Applied Biologists and John Wiley & Sons Ltd.

  2. Strain Tuning of the Charge Density Wave in Monolayer and Bilayer 1T-TaS2

    KAUST Repository

    Gan, Liyong

    2015-12-07

    By first-principles calculations, we investigate the strain effects on the charge density wave states of monolayer and bilayer 1T-TaS2. The modified stability of the charge density wave in the monolayer is understood in terms of the strain dependent electron localization, which determines the distortion amplitude. On the other hand, in the bilayer the effect of strain on the interlayer interaction is also crucial. The rich phase diagram under strain opens new venues for applications of 1T-TaS2. We interpret the experimentally observed insulating state of bulk 1T-TaS2 as inherited from the monolayer by effective interlayer decoupling.

  3. Signature inversion of the semi-decoupled band in the odd-odd nucleus 170Ta

    International Nuclear Information System (INIS)

    Deng Fuguo; Yang Chunxiang; Zhou Hongyu; Sun Huibin; Lu Jingbin; Zhao Guangyi; Yin Lichang; Liu Yunzuo

    2001-01-01

    The high-spin states of the odd-odd nucleus 170 Ta have been studied by the 155 Gd( 19 F, 4n) 170 Ta reaction at the beam energy of 97 MeV. The α = 1 sequence of the semi-decoupled band has been pushed to higher-spin states and the signature inversion point was observed at 19.5 ℎ. the results are compared with those of the neighbouring odd-odd nuclei

  4. Influence of Ta and Ti Doping on the High Field Performance of (Nb, Ta, Ti)3Sn Multifilamentary Wires based on Osprey Bronze with High Tin Content

    International Nuclear Information System (INIS)

    Abaecherli, V; Uglietti, D; Lezza, P; Seeber, B; Fluekiger, R; Cantoni, M; Buffat, P-A

    2006-01-01

    Ta and Ti are the most widely used additions for technical Nb 3 Sn multifilamentary superconductors. These elements are known to influence grain growth, grain morphology and chemical composition in the A15 layer, hence the current carrying properties of the wires over a wide magnetic field range. So far only few studies tried to compare systematically Ta and Ti doped and undoped Nb 3 Sn wires in the frame of the same work, down to a nanometric scale. We present an investigation on several multifilamentary (Nb, Ta, Ti) 3 Sn bronze route wires, fabricated at a laboratory scale, with various amounts of additives. The wires consist of fine filaments embedded in a Cu-Sn or Cu-Sn-Ti Osprey bronze with > 15 wt.% Sn and an external Cu stabilization. Microstructural observations are compared with the results of J c and n values measured up to 21 T at 4.2 and 2.2 K, and for longitudinal strains up to 0.5%. Non-Cu J c values up to 300 Amm -2 and n values up to 50 at 17 T and 4.2 K show clearly that wires with Ti addition to the bronze have a better performance with respect to wires with Ti additions to the filaments

  5. Study of dissolution factors of U, Th and Ta

    International Nuclear Information System (INIS)

    Santos, Maristela; Medeiros, Geiza; Zouain, Felipe; Cunha, Kenya Dias da; Pitassi, Gabriel; Lima, Cintia; Leite, Carlos Vieira Barros; Nascimento, Jose Eduardo; Dalia, Kely Cristina

    2009-01-01

    Air pollution can be a problem in industrial processes, but monitoring and controlling the aerosols in the work place is not enough to estimate the occupational risk due to dust particle inhalation. The solubility in lung fluid is considered to estimate this risk. The aim of this study is to determine in vitro specific dissolution parameters for thorium (Th), uranium (U) and tantalum (Ta) associated to crystal lattice of a niobium mineral (pyrochlore). Th, U and Ta dissolution factors in vitro were obtained using the Gamble solution (Simulant Lung Fluid, SLF), PIXE (Particle Induced X ray Emission) and alpha spectrometry as analytical techniques. Ta, Th and U are present in the pyrochlore crystal lattice as oxide; however they have shown different dissolution parameters. The rapid dissolution fraction (fr), rapid dissolution rate (λr); slow dissolution rate (fs) and slow dissolution fraction ((λs) measured for tantalum oxide were equal to 0.1, 0.45 d -1 and 0.00007 d -1 , respectively; for uranium oxide fr was equal to 0.05, (λr equal to 1.1 d -1 ; (λs equal to 0.000068 d -1 ; for thorium oxide fr was 0.025, (λr was 1.5 d -1 and (λs: 0.000065 d -1 . These results show that chemical behavior of these 3 compounds in the SLF could not be represented by the same parameter. The ratio of uranium concentration in urine and feces samples from workers exposed to pyrochlore dust particle was determined. These values agree with the theoretical values of estimated uranium concentration using specific parameters for uranium oxide present in pyrochlore. (author)

  6. Usefulness of blood irradiation before transfusion to avoid transfusion associated graft versus host disease (TA-GVHD)

    International Nuclear Information System (INIS)

    Takahashi, Koki

    1997-01-01

    We summarize the pathology of the transfusion associated graft versus host disease (TA-GVHD) and examine the usefulness of the blood irradiation before transfusion as more widely used prophylaxis. The symptom of TA-GVHD was as follows: after (asymptomatic phase) for 1 to 2 weeks after blood transfusion, pyrexia and erythema appeared. Furthermore, hepatic disorder, diarrhea and bloody stool occurred. In no longer time, pancytopenia by aplastic crisis of the bone marrow appeard, and severe granulocytopenia occurred. Finally, by the complication with severe infectious disease such as septicemia, almost all the patients died with in 3 to 4 weeks after blood transfusion. TA-GVHD was found in some patients without immune deficiency syndrome. The cause of the frequent occurrence of the disease in Japan was shown by the probability of the one-way matching analysis. As the countermeasure of TA-GVHD, we examined the effectiveness of the blood irradiation before transfusion under the consideration of the safety and the emergency. After the responder cells were beforehand irradiated with various doses of radiation (X-ray or g-ray), the proliferative response was investigated through the uptake of 3 H-thymidine, and we obtained 15-50 Gy as the optimum dose of the radiation. We discuss the establishment of the countermeasure for the TA-GVHD and the formation of the nationwide support system for TV-GVHD (K.H.). 33 refs

  7. The role of the F-box gene TaFBA1 from wheat (Triticum aestivum L.) in drought tolerance.

    Science.gov (United States)

    Zhou, Shumei; Sun, Xiudong; Yin, Suhong; Kong, Xiangzhu; Zhou, Shan; Xu, Ying; Luo, Yin; Wang, Wei

    2014-11-01

    Drought is one of the most important factors limiting plant growth and development. We identified a gene in wheat (Triticum aestivum L.) under drought stress named TaFBA1. TaFBA1 encodes a putative 325-amino-acid F-box protein with a conserved N-terminal F-box domain and a C-terminal AMN1 domain. Real-time RT-PCR analysis revealed that TaFBA1 transcript accumulation was upregulated by high-salinity, water stress, and abscisic acid (ABA) treatment. To evaluate the functions of TaFBA1 in the regulation of drought stress responses, we produced transgenic tobacco lines overexpressing TaFBA1. Under water stress conditions, the transgenic tobacco plants had a higher germination rate, higher relative water content, net photosynthesis rate (Pn), less chlorophyll loss, and less growth inhibition than WT. These results demonstrate the high tolerance of the transgenic plants to drought stress compared to the WT. The enhanced oxidative stress tolerance of these plants, which may be involved in their drought tolerance, was indicated by their lower levels of reactive oxygen species (ROS) accumulation, MDA content, and cell membrane damage under drought stress compared to WT. The antioxidant enzyme activities were higher in the transgenic plants than in WT, which may be related to the upregulated expression of some antioxidant genes via overexpression of TaFBA1. Copyright © 2014 Elsevier Masson SAS. All rights reserved.

  8. The Mo/Ta (100) interface

    International Nuclear Information System (INIS)

    Quintanar, C.; Velasco, V.R.; Garcia-Moliner, F.

    1990-12-01

    We have calculated the interface local density of states (ILDOS) formed by the transition metals Mo/Ta using a tight-binding Slater-Koster description and the Green Function matching method together with quickly converging algorithms to compute the transfer matrices. We obtain the surface LDOS as a byproduct. Our result is a useful tool to analyze experimental results and to check models as a function of the value of the tight-binding parameters either of the bulk or at the interface itself. We consider the (100) direction. We compare the interface to the bulk and to the surface and comment on some recently found experimental results for this interface. (author). 17 refs, 2 figs

  9. Photocatalytic hydrogen production using visible-light-responsive Ta 3N5 photocatalyst supported on monodisperse spherical SiO2 particulates

    KAUST Repository

    Liu, Xiaoming; Zhao, Lan; Domen, Kazunari; Takanabe, Kazuhiro

    2014-01-01

    Fine nanoparticles of Ta3N5 (10-20 nm) were synthesized on the surfaces of SiO2 spheres with a diameter of ∼550 nm. A sol-gel method was used to modify the surface of SiO2 with Ta2O5 from TaCl5 dissolved in ethanol in the presence of citric acid

  10. A CBL-Interacting Protein Kinase TaCIPK2 Confers Drought Tolerance in Transgenic Tobacco Plants through Regulating the Stomatal Movement.

    Science.gov (United States)

    Wang, Yan; Sun, Tao; Li, Tingting; Wang, Meng; Yang, Guangxiao; He, Guangyuan

    2016-01-01

    In plants, the CBL-CIPK signaling pathways play key roles in the response to abiotic stresses. However, functional studies of CIPKs in the important staple crop wheat are very rare. In this study, we identified a CIPK gene from wheat, designated TaCIPK2. Expression analysis results showed that TaCIPK2 could be up-regulated in wheat leaves by polyethylene glycol, abscisic acid and H2O2 treatments. Subcellular localization analyses revealed that TaCIPK2 was present in whole wheat epidermal cells. A yeast two-hybrid assay indicated that TaCIPK2 interacted with TaCBL1, 2, 3 and 4 in vitro. Transgenic tobacco plants over-expressing TaCIPK2 exhibited increased drought tolerance, indicated by a larger proportion of green cotyledons and higher survival rates under the osmotic and drought stress conditions compared with control plants. Additionally, physiological index analyses revealed that the transgenic tobacco plants had lower water loss rates and ion leakage, accumulated less malondialdehyde and H2O2, and had higher catalase and superoxide dismutase activities than the control plants. The transgenic plants also exhibited faster stomatal closure following exposure to osmotic stress conditions. The seed germination rates and stomatal aperture of TaCIPK2-overexpressing tobacco plants decreased after exogenous abscisic acid treatment was applied, implying that the transgenic tobacco plants were more sensitive to exogenous abscisic acid than the control plants. Our results indicate that TaCIPK2 plays a positive regulatory role in drought stress responses in transgenic tobacco plants.

  11. The involvement of wheat F-box protein gene TaFBA1 in the oxidative stress tolerance of plants.

    Directory of Open Access Journals (Sweden)

    Shu-Mei Zhou

    Full Text Available As one of the largest gene families, F-box domain proteins have been found to play important roles in abiotic stress responses via the ubiquitin pathway. TaFBA1 encodes a homologous F-box protein contained in E3 ubiquitin ligases. In our previous study, we found that the overexpression of TaFBA1 enhanced drought tolerance in transgenic plants. To investigate the mechanisms involved, in this study, we investigated the tolerance of the transgenic plants to oxidative stress. Methyl viologen was used to induce oxidative stress conditions. Real-time PCR and western blot analysis revealed that TaFBA1 expression was up-regulated by oxidative stress treatments. Under oxidative stress conditions, the transgenic tobacco plants showed a higher germination rate, higher root length and less growth inhibition than wild type (WT. The enhanced oxidative stress tolerance of the transgenic plants was also indicated by lower reactive oxygen species (ROS accumulation, malondialdehyde (MDA content and cell membrane damage under oxidative stress compared with WT. Higher activities of antioxidant enzymes, including superoxide dismutase (SOD, catalase (CAT, ascorbate peroxidase (APX and peroxidase (POD, were observed in the transgenic plants than those in WT, which may be related to the upregulated expression of some antioxidant genes via the overexpression of TaFBA1. In others, some stress responsive elements were found in the promoter region of TaFBA1, and TaFBA1 was located in the nucleus, cytoplasm and plasma membrane. These results suggest that TaFBA1 plays an important role in the oxidative stress tolerance of plants. This is important for understanding the functions of F-box proteins in plants' tolerance to multiple stress conditions.

  12. Methylene blue degradation by NaTaO3 sol-gel doped with Sm and La

    International Nuclear Information System (INIS)

    Torres-Martinez, Leticia M.; Cruz-Lopez, Arquimedes; Juarez-Ramirez, Isaias; Meza-de la Rosa, Ma. Elena

    2009-01-01

    In this work, NaTaO 3 compounds doped with 1 M% of La and Sm, were prepared by the sol-gel (SG) method and solid state (SS) reaction; and tested as photocatalysts on the degradation of methylene blue (MB) under UV light. The structural characterization by X-ray powder diffraction revealed that the crystallization of the NaTaO 3 phase prepared by the sol-gel method started at 600 deg. C, reaching maximum crystallization at 800 deg. C. It was determined that the presence of Sm and La retard the crystallization of the NaTaO 3 phase. On the other hand, the compounds synthesized in this work showed particle sizes in the nanometric scale, as it was observed by scanning electron microscopy (SEM). The specific surface area of the compounds synthesized by the sol-gel method, showed values 4 times higher than those obtained by the solid state reaction, favoring their functional and photocatalytic performance in the methylene blue degradation. In addition, the best photocatalytic performance was shown by the NaTaO 3 doped with Sm and heated at 600 deg. C, having a half-life time of 65 min.

  13. Superior H2 production by hydrophilic ultrafine Ta2O5 engineered covalently on graphene

    International Nuclear Information System (INIS)

    Mao, Lin; Zhu, Shenmin; Shi, Dian; Chen, Yixin; Yin, Chao; Li, Yao; Zhang, Di; Ma, Jun; Chen, Zhixin

    2014-01-01

    A H 2 O 2 -mediated hydrothermal method was developed for the fabrication of hydrophilic Ta 2 O 5 /graphene composite. The composite shows a superior H 2 productivity, up to 30 mmol g −1 h −1 when used as a photocatalyst for water splitting, corresponding to an apparent quantum efficiency of 33.8% at 254 nm. This superior performance is due to the hydrophilic nature of the composite and more importantly due to the ultrafine Ta 2 O 5 nanoparticles (about 4.0 ± 1.5 nm) which are covalently bonded with the conductive graphene. The hydrophilic property of the composite is attributed to the use of H 2 O 2 in the hydrothermal process. The ultrafine size of the Ta 2 O 5 particles which are covalently bonded with the graphene sheets is attributed to the use of sonication in the synthesis process. Furthermore, the hydrophilic Ta 2 O 5 /Gr composite is durable, which is beneficial to long term photocatalysis. The strategy reported here provides a new approach to designing photocatalysts with superior performance for H 2 production. (papers)

  14. Fabrication of Ta nanoparticles induced by nanosecond laser ablation in ethanol: the study of laser fluence effects

    Science.gov (United States)

    Azadi Kenari, Fariba; Moniri, Samira; Hantehzadeh, Mohammad Reza; Dorranian, Davoud; Ghoranneviss, Mahmood

    2018-05-01

    Tantalum nanoparticles (Ta NPs) were synthesized in ethanol solution by ablation with a 1064 nm Nd:YAG laser. Prepared NPs were investigated by UV-visible absorption spectroscopy, Transmission electron microscopy, X-ray diffraction and Photoluminescence measurement. The average sizes of NPs were calculated to be in the range of 12-18 nm. From the UV-visible studies, the plasmon peak position of Ta NPs was observed in the spectral range of 206-208 nm. The XRD spectra clearly showed the crystalline structure of NPs and various peaks of Ta and Ta2O5. Moreover, the UV region in the PL spectrum included the free exciton and the bound exciton emission correlated with the defect concentration. In fact, the laser ablation in the organic and inorganic solvents is a strong technique to obtain some NPs with particular structures, which are impossible to produce by conventional methods.

  15. The effect of low energy helium ion irradiation on tungsten-tantalum (W-Ta) alloys under fusion relevant conditions

    Science.gov (United States)

    Gonderman, S.; Tripathi, J. K.; Novakowski, T. J.; Sizyuk, T.; Hassanein, A.

    2017-08-01

    Currently, tungsten remains the best candidate for plasma-facing components (PFCs) for future fusion devices because of its high melting point, low erosion, and strong mechanical properties. However, continued investigation has shown tungsten to undergo severe morphology changes under fusion-like conditions. These results motivate the study of innovative PFC materials which are resistant to surface morphology evolution. The goal of this work is to examine tungsten-tantalum (W-Ta) alloys, a potential PFC material, and their response to low energy helium ion irradiation. Specifically, W-Ta samples are exposed to 100 eV helium irradiations with a flux of 1.15 × 1021 ions m-2 s-1, at 873 K, 1023 K, and 1173 K for 1 h duration. Scanning electron microscopy (SEM) reveals significant changes in surface deterioration due to helium ion irradiation as a function of both temperature and tantalum concentration in W-Ta samples. X-Ray Diffraction (XRD) studies show a slight lattice parameter expansion in W-Ta alloy samples compared to pure W samples. The observed lattice parameter expansion in W-Ta alloy samples (proportional to increasing Ta wt.% concentrations) reflect significant differences observed in the evolution of surface morphology, i.e., fuzz development processes for both increasing Ta wt.% concentration and target temperature. These results suggest a correlation between the observed morphology differences and the induced crystal structure change caused by the presence of tantalum. Shifts in the XRD peaks before and after 100 eV helium irradiation with a flux of 1.15 × 1021 ions m-2 s-1, 1023 K, for 1 h showed a significant difference in the magnitude of the shift. This has suggested a possible link between the atomic spacing of the material and the accumulated damage. Ongoing research is needed on W-Ta alloys and other innovative materials for their application as irradiation resistant materials in future fusion or irradiation environments.

  16. Electronic Properties of a TMTTF-Family Salt, (TMTTF)2TaF6: New Member Located on the Modified Generalized Phase-Diagram

    Science.gov (United States)

    Iwase, Fumitatsu; Sugiura, Koichi; Furukawa, Ko; Nakamura, Toshikazu

    2009-10-01

    A new TMTTF (tetramethyl-tetrathia-fulvalene)-family salt, (TMTTF)2TaF6, which has the largest octahedral (Oh) symmetry counter anion among the various salts in the TMTTF family, was prepared. X-ray, static magnetic susceptibility, electron spin resonance (ESR) and nuclear magnetic resonance (NMR) measurements were carried out in order to investigate the electronic state of (TMTTF)2TaF6. The unit-cell volume of (TMTTF)2TaF6 is larger than that of (TMTTF)2MF6 (M=P, As, and Sb). (TMTTF)2TaF6 shows the highest charge-ordering phase transition temperature (TCO˜ 175 K) among TMTTF salts with the Oh-symmetry counter anion. These facts indicate that (TMTTF)2TaF6 is located on the most negative side in the generalized phase-diagram for TMTCF family salts. (TMTTF)2TaF6 undergoes an antiferromagnetic transition around 9 K. It turned out the phase diagram needs to be modified.

  17. Synthesis and visible-light-driven photocatalytic activity of p–n heterojunction Ag_2O/NaTaO_3 nanocubes

    International Nuclear Information System (INIS)

    Yang, Songbo; Xu, Dongbo; Chen, Biyi; Luo, Bifu; Yan, Xu; Xiao, Lisong; Shi, Weidong

    2016-01-01

    Highlights: • We firstly report a facile way to prepare the visible-light-driven Ag_2O/NaTaO_3p–n heterojunction by chemical precipitation method. • The Ag_2O/NaTaO_3 heterojunction shows the highest photocatalytic activity than the pure NaTaO_3 and Ag_2O nanoparticles under visible light. • The enhancement of the heterojunction photocatalytic activity was discussed and the photocatalytic mechanism was tested in our paper. • In summary, we think that the Ag_2O/NaTaO_3 heterojunction with the strong visible light absorption and efficient photocatalytic activity have been extended application in photocatalysis for organic dyes pollutants degradation and purification of water. - Abstract: The constructing of p–n heterojunction photocatalytic system has received much attention in environmental purification and hydrogen generation from water. In this study, an efficient visible-light-driven p–n heterojunction Ag_2O/NaTaO_3 was successfully prepared by chemical precipitation method at room temperature. It showed an enhanced photocatalytic activity for the degradation of rhodamine B (RhB) under visible-light irradiation, much higher than those of either individual Ag_2O or NaTaO_3. The reactive species scavenger results indicated the superoxide anion radicals (·O"2"−) played key roles in RhB decoloration. From the experimental results and the relative band gap position of these semiconductors, a detailed possible photocatalytic mechanism of the Ag_2O/NaTaO_3 heterojunction under visible light was proposed. The enhancement of the photocatalytic activity was attributed to the interfacial electronic interaction between NaTaO_3 and Ag_2O and the high migration efficiency of photogenerated carriers.

  18. Overexpression of the Wheat Expansin Gene TaEXPA2 Improved Seed Production and Drought Tolerance in Transgenic Tobacco Plants.

    Science.gov (United States)

    Chen, Yanhui; Han, Yangyang; Zhang, Meng; Zhou, Shan; Kong, Xiangzhu; Wang, Wei

    2016-01-01

    Expansins are cell wall proteins that are grouped into two main families, α-expansins and β-expansins, and they are implicated in the control of cell extension via the disruption of hydrogen bonds between cellulose and matrix glucans. TaEXPA2 is an α-expansin gene identified in wheat. Based on putative cis-regulatory elements in the TaEXPA2 promoter sequence and the expression pattern induced when polyethylene glycol (PEG) is used to mimic water stress, we hypothesized that TaEXPA2 is involved in plant drought tolerance and plant development. Through transient expression of 35S::TaEXPA2-GFP in onion epidermal cells, TaEXPA2 was localized to the cell wall. Constitutive expression of TaEXPA2 in tobacco improved seed production by increasing capsule number, not seed size, without having any effect on plant growth patterns. The transgenic tobacco exhibited a significantly greater tolerance to water-deficiency stress than did wild-type (WT) plants. We found that under drought stress, the transgenic plants maintained a better water status. The accumulated content of osmotic adjustment substances, such as proline, in TaEXPA2 transgenic plants was greater than that in WT plants. Transgenic plants also displayed greater antioxidative competence as indicated by their lower malondialdehyde (MDA) content, relative electrical conductivity, and reactive oxygen species (ROS) accumulation than did WT plants. This result suggests that the transgenic plants suffer less damage from ROS under drought conditions. The activities of some antioxidant enzymes as well as expression levels of several genes encoding key antioxidant enzymes were higher in the transgenic plants than in the WT plants under drought stress. Collectively, our results suggest that ectopic expression of the wheat expansin gene TaEXPA2 improves seed production and drought tolerance in transgenic tobacco plants.

  19. Recoil range distribution measurement in 20Ne + 181Ta reaction

    International Nuclear Information System (INIS)

    Tripathi, R.; Sudarshan, K.; Goswami, A.; Guin, R.; Reddy, A.V.R.

    2005-01-01

    In order to investigate linear momentum transfer in various transfer channels in 20 Ne + 181 Ta, recoil range distribution measurements have been carried out at E lab = 180 MeV, populating significant number of l-waves above l crit

  20. GPR - Ground penetration radar u prospekciji ležišta arhitektonskog kamena

    OpenAIRE

    Rukavina, Tihomir

    2010-01-01

    Prikazuju se osnove geofizičke metode GPR (Ground Penetratig Radar) i neke specifičnosti pri prospekciji ležišta arhitektonskog kamena. Uređajem je moguće uočiti diskontinuitete i neke druge geološke i geotehničke karakteristike ležišta koji bitno pridonose ekonomskim parametrima eksploatacije. Bitna odlika metode GPR-a je direktno detektiranje položaja i smjera pružanja diskontinuiteta, zona anizotropne ili erodirane građe stijenske mase kao i prisustvo kaverni i drugih ...

  1. Spin Hall magnetoresistance in Ta/CoFe2O4 nanostructures

    Science.gov (United States)

    Hui, Ya-Juan; Cheng, Wei-Ming; Zhang, Zhao-Bing; Ji, Hong-Kai; Cheng, Xiao-Min; You, Long; Miao, Xiang-Shui

    2016-07-01

    Spin Hall magnetoresistance (SMR) has been investigated in Ta/CoFe2O4 nanostructures grown on different substrates. Spin currents in CoFe2O4 films are electrically detected in adjacent Ta layers owing to inverse spin Hall effects. The sign of the magnetic-field-dependent resistivity signal shows different polarities along different axes, showing different spin-dependent electron transports. A cosinelike curve of the angular dependence signal with opposite polarity is observed in two orthogonal magnetization planes, whereas a basic line is observed in another plane, revealing the spin accumulation phenomenon. The roughness of the CoFe2O4 surface tuned by substrate strains is responsible for the extent of spin accumulations and the strength of the SMR signal in the nanostructures.

  2. The Effects of Al and Ti Additions on the Structural Stability, Mechanical and Electronic Properties of D8m-Structured Ta5Si3

    Directory of Open Access Journals (Sweden)

    Linlin Liu

    2016-05-01

    Full Text Available In the present study, the influence of substitutional elements (Ti and Al on the structural stability, mechanical properties, electronic properties and Debye temperature of Ta5Si3 with a D8m structure were investigated by first principle calculations. The Ta5Si3 alloyed with Ti and Al shows negative values of formation enthalpies, indicating that these compounds are energetically stable. Based on the values of formation enthalpies, Ti exhibits a preferential occupying the Ta4b site and Al has a strong site preference for the Si8h site. From the values of the bulk modulus (B, shear modulus (G and Young’s modulus (E, we determined that both Ti and Al additions decrease both the shear deformation resistance and the elastic stiffness of D8m structured Ta5Si3. Using the shear modulus/bulk modulus ratio (G/B, Poisson’s ratio (υ and Cauchy’s pressure, the effect of Ti and Al additions on the ductility of D8m-structured Ta5Si3 are explored. The results show that Ti and Al additions reduce the hardness, resulting in solid solution softening, but improve the ductility of D8m-structured Ta5Si3. The electronic calculations reveal that Ti and Al additions change hybridization between Ta-Si and Si-Si atoms for the binary D8m-structured Ta5Si3. The new Ta-Al bond is weaker than the Ta-Si covalent bonds, reducing the covalent property of bonding in D8m-structured Ta5Si3, while the new strong Ti4b-Ti4b anti-bonding enhances the metallic behavior of the binary D8m-structured Ta5Si3. The change in the nature of bonding can well explain the improved ductility of D8m-structured Ta5Si3 doped by Ti and Al. Moreover, the Debye temperatures, ΘD, of D8m-structured Ta5Si3 alloying with Ti and Al are decreased as compared to the binary Ta5Si3.

  3. Effect of the adhesive antibiotic TA on adhesion and initial growth of E-coli on silicone rubber

    NARCIS (Netherlands)

    Simhi, E; van der Mei, HC; Ron, EZ; Rosenberg, E; Busscher, HJ

    2000-01-01

    Catheter-associated urinary tract infection is the most common nosocomial infection, and contributes to patient morbidity and mortality. We investigated the effect that the TA adhesive antibiotic had on adhesion and initial growth in urine of Escherichia coli on silicone rubber. The TA antibiotic

  4. Interpreting Medieval Inter-tidal Features at Weelie's Taing on Papa Westray, Orkney, NE Scotland

    Science.gov (United States)

    Pollard, Edward; Gibson, Julie; Littlewood, Mark

    2016-12-01

    Investigation of the inter-tidal heritage of the Orkney Islands is used to interpret a previously perplexing complex at Weelie's Taing on Papa Westray. The study revealed a previously unknown type of harbour since identified in several locations around Orkney. Situated in exposed environmental situations, shelter is formed by an `ayre', a type of spit that encloses a loch, and which has been used historically as a landing place or crossing of the inter-tidal zone. A complex landing area, pier, tower and ship-blockage suggest Weelie's Taing was used as a harbour. Important fishing grounds exploited since the Neolithic are nearby, and Papa Westray was the site of water-focussed religious communities. It is suggested that Weelie's Taing was in use in the medieval period when Papa Westray was less isolated than today with the presence of ecclesiastical communities and situation on the Orkney-Shetland route.

  5. Resistance to He{sup 2+} irradiation damage in metallic glass Ta{sub 38}Ni{sub 62}

    Energy Technology Data Exchange (ETDEWEB)

    Hou, Wenjing [Key Laboratory of Materials Modification by Laser, Ion and Electron Beams (Dalian University of Technology), Ministry of Education, Dalian 116024 (China); Mei, Xianxiu, E-mail: xxmei@dlut.edu.cn [Key Laboratory of Materials Modification by Laser, Ion and Electron Beams (Dalian University of Technology), Ministry of Education, Dalian 116024 (China); Zhang, Xiaonan; Wang, Yingmin; Qiang, Jianbing [Key Laboratory of Materials Modification by Laser, Ion and Electron Beams (Dalian University of Technology), Ministry of Education, Dalian 116024 (China); Sun, Jianrong [Institute of Modern Physics, The Chinese Academy of Sciences, Lanzhou 730000 (China); Wang, Younian [Key Laboratory of Materials Modification by Laser, Ion and Electron Beams (Dalian University of Technology), Ministry of Education, Dalian 116024 (China)

    2016-10-15

    Highlights: • Metallic glass Ta{sub 38}Ni{sub 62} irradiated by different fluence of He{sup 2+} remained amorphous. • The helium bubble layer appeared at the end of ion range 1.01 μm away from surface. • Helium bubbles were larger in the layer center and reduced to top and bottom sides. • No significant damage appeared in the surface of metallic glass Ta{sub 38}Ni{sub 62}. • Ta{sub 38}Ni{sub 62} better resisted to He{sup 2+} irradiation than W and V{sub 87.5}Cr{sub 4.17}Ti{sub 4.17}Nb{sub 4.17}. - Abstract: Metallic glass Ta{sub 38}Ni{sub 62} strips, metallic W, and V{sub 87.5}Cr{sub 4.17}Ti{sub 4.17}Nb{sub 4.17} alloy were irradiated using a 500 keV He{sup 2+} ion beam at different fluence to compare the metallic glass resistance to irradiation. Metallic glass Ta{sub 38}Ni{sub 62} remained amorphous at different He{sup 2+} irradiation fluence. Transmission electron microscopy analysis revealed the presence of helium bubbles at the end of the range of helium ions in the metallic glass. No significant damage resulted in the metallic glass surface, and the root mean square roughness increased nonlinearly with the increase in fluence. At 1 × 10{sup 18} ions/cm{sup 2}, metallic W appeared in larger sunken areas on the surface and V{sub 87.5}Cr{sub 4.17}Ti{sub 4.17}Nb{sub 4.17} alloy experienced multi-layer flaking. The metallic glass Ta{sub 38}Ni{sub 62} resistance to He{sup 2+} ion beam irradiation was better than that of metallic W, and that of the V{sub 87.5}Cr{sub 4.17}Ti{sub 4.17}Nb{sub 4.17} alloy was the poorest.

  6. Influence of temperature on oxidation mechanisms of fiber-textured AlTiTaN coatings.

    Science.gov (United States)

    Khetan, Vishal; Valle, Nathalie; Duday, David; Michotte, Claude; Delplancke-Ogletree, Marie-Paule; Choquet, Patrick

    2014-03-26

    The oxidation kinetics of AlTiTaN hard coatings deposited at 265 °C by DC magnetron sputtering were investigated between 700 and 950 °C for various durations. By combining dynamic secondary ion mass spectrometry (D-SIMS), X-ray diffraction (XRD), and transmission electron microscopy (TEM) investigations of the different oxidized coatings, we were able to highlight the oxidation mechanisms involved. The TEM cross-section observations combined with XRD analysis show that a single amorphous oxide layer comprising Ti, Al, and Ta formed at 700 °C. Above 750 °C, the oxide scale transforms into a bilayer oxide comprising an Al-rich upper oxide layer and a Ti/Ta-rich oxide layer at the interface with the coated nitride layer. From the D-SIMS analysis, it could be proposed that the oxidation mechanism was governed primarily by inward diffusion of O for temperatures of ≤700 °C, while at ≥750 °C, it is controlled by outward diffusion of Al and inward diffusion of O. Via a combination of structural and chemical analysis, it is possible to propose that crystallization of rutile lattice favors the outward diffusion of Al within the AlTiTa mixed oxide layer with an increase in the temperature of oxidation. The difference in the mechanisms of oxidation at 700 and 900 °C also influences the oxidation kinetics with respect to oxidation time. Formation of a protective alumina layer decreases the rate of oxidation at 900 °C for long durations of oxidation compared to 700 °C. Along with the oxidation behavior, the enhanced thermal stability of AlTiTaN compared to that of the TiAlN coating is illustrated.

  7. Synthesis quality control and biodistribution of technetium-99m triamcinolone (99mTc-TA) complex: An inflammation tracer agent

    International Nuclear Information System (INIS)

    Rizvii, Faheem Askari; Naqvi, Syed Ali Raza; Mehdi, Muhammad; Roohi, Samina; Zahoor, Ameer Fawad; Khan, Zulfiqar Ali; Sohaib, Muhammad; Rasheed, Rashid

    2017-01-01

    In present study synthesis of 99m Tc-triamcinolone acetonide ( 99m Tc-TA) complex and its stability using set of quality control parameters such as ligand concentration, reducing agent concentration, pH, temperature and reaction time was assessed. 99m Tc-TA complex was characterized in terms of percent (%) yield, stability in saline and serum using chromatographic procedures. Radiochemically the 99m Tc-TA complex was found quite stable in saline and serum. After 30 min of reaction the complex showed maximum radiochemical yield of 96.32% which decreased to 96.25 % after 4 h incubation period. In serum, the % yield of radiochemical was remained same up to 2 h which decreased to 93.5% at 24 h time point. Normal biodistribution pattern in Sprague-Dawley rats revealed liver, stomach and kidneys as areas of high 99m Tc-TA complex uptake (8.44 ±1.32, 8.75 ± 1.03 and 12.67 ± 1.21%, respectively) at 1 h post injection time point. Scintigraphy of 99m Tc-TA in rabbits showed similar eco as observed in biodistribution study. Based on the promising results obtained in context of in vitro and in vivo stability and biodistribution, 99m Tc-TA complex could be further studied to identify the inflammation based diseases

  8. Effects of Y incorporation in TaON gate dielectric on electrical performance of GaAs metal-oxide-semiconductor capacitor

    Energy Technology Data Exchange (ETDEWEB)

    Liu, Li Ning; Choi, Hoi Wai; Lai, Pui To [Department of Electrical and Electronic Engineering, The University of Hong Kong (China); Xu, Jing Ping [School of Optical and Electronic Information, Huazhong University of Science and Technology, Wuhan (China)

    2016-09-15

    In this study, GaAs metal-oxide-semiconductor (MOS) capacitors using Y-incorporated TaON as gate dielectric have been investigated. Experimental results show that the sample with a Y/(Y + Ta) atomic ratio of 27.6% exhibits the best device characteristics: high k value (22.9), low interfacestate density (9.0 x 10{sup 11} cm{sup -2} eV{sup -1}), small flatband voltage (1.05 V), small frequency dispersion and low gate leakage current (1.3 x 10{sup -5}A/cm{sup 2} at V{sub fb} + 1 V). These merits should be attributed to the complementary properties of Y{sub 2}O{sub 3} and Ta{sub 2}O{sub 5}:Y can effectively passivate the large amount of oxygen vacancies in Ta{sub 2}O{sub 5}, while the positively-charged oxygen vacancies in Ta{sub 2}O{sub 5} are capable of neutralizing the effects of the negative oxide charges in Y{sub 2}O{sub 3}. This work demonstrates that an appropriate doping of Y content in TaON gate dielectric can effectively improve the electrical performance for GaAs MOS devices. (copyright 2016 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

  9. Particle size dependence on oxygen reduction reaction activity of electrodeposited TaOx catalysts in acidic media

    KAUST Repository

    Seo, J.

    2013-11-13

    The size dependence of the oxygen reduction reaction activity was studied for TaOx nanoparticles electrodeposited on carbon black for application to polymer electrolyte fuel cells (PEFCs). Compared with a commercial Ta2O5 material, the ultrafine oxide nanoparticles exhibited a distinctively high onset potential different from that of the bulky oxide particles.

  10. Control of electrical resistivity of TaN thin films by reactive sputtering for embedded passive resistors

    International Nuclear Information System (INIS)

    Kang, S.M.; Yoon, S.G.; Suh, S.J.; Yoon, D.H.

    2008-01-01

    Tantalum nitride thin films were deposited by radio frequency (RF) reactive sputtering at various N 2 /Ar gas flow ratios and working pressures to examine the change of their electrical resistivity. From the X-ray diffraction (XRD) and four-point probe sheet resistance measurements of the TaN x films, it was found that the change of the crystalline structures of the TaN x films as a function of the N 2 partial pressure caused an abrupt change of the electrical resistivity. When the hexagonal structure TaN thin films changed to an f.c.c. structure, the sheet resistance increased from 16 Ω/sq to 1396 Ω/sq. However, we were able to control the electrical resistivity of the TaN thin film in the range from 69 Ω/sq to 875 Ω/sq, with no change in crystalline structure, within a certain range of working pressures. The size of the grains in the scanning electron microscopy (SEM) images seemed to decrease with the increase of working pressure

  11. High-quality single crystal growth and magnetic property of Mn4Ta2O9

    Science.gov (United States)

    Cao, Yiming; Xu, Kun; Yang, Ya; Yang, Wangfan; Zhang, Yuanlei; Kang, Yanru; He, Xijia; Zheng, Anmin; Liu, Mian; Wei, Shengxian; Li, Zhe; Cao, Shixun

    2018-06-01

    A large-size single crystal of Mn4Ta2O9 with ∼3.5 mm in diameter and ∼65 mm in length was successfully grown for the first time by a newly designed one-step method based on the optical floating zone technique. Both the clear Laue spots and sharp XRD Bragg reflections suggest the high quality of the single crystal. In Mn4Ta2O9 single crystal, an antiferromagnetic phase transition was observed below Néel temperature 102 K along c axis, which is similar to the isostructural compound Mn4Nb2O9, but differs from the isostructural Co4Nb2O9. Relative dielectric constant at 30 kOe suggests that no magnetoelectric coupling exists in Mn4Ta2O9.

  12. Spin polarization driven by a charge-density wave in monolayer 1T−TaS2

    KAUST Repository

    Zhang, Qingyun

    2014-08-06

    Using first-principles calculations, we investigate the electronic and vibrational properties of monolayer T-phase TaS2. We demonstrate that a charge-density wave is energetically favorable at low temperature, similar to bulk 1T-TaS2. Electron-phonon coupling is found to be essential for the lattice reconstruction. The charge-density wave results in a strong localization of the electronic states near the Fermi level and consequently in spin polarization, transforming the material into a magnetic semiconductor with enhanced electronic correlations. The combination of inherent spin polarization with a semiconducting nature distinguishes the monolayer fundamentally from the bulk compound as well as from other two-dimensional transition metal dichalcogenides. Monolayer T-phase TaS2 therefore has the potential to enable two-dimensional spintronics. © 2014 American Physical Society.

  13. Spin polarization driven by a charge-density wave in monolayer 1T−TaS2

    KAUST Repository

    Zhang, Qingyun; Gan, Liyong; Cheng, Yingchun; Schwingenschlö gl, Udo

    2014-01-01

    Using first-principles calculations, we investigate the electronic and vibrational properties of monolayer T-phase TaS2. We demonstrate that a charge-density wave is energetically favorable at low temperature, similar to bulk 1T-TaS2. Electron-phonon coupling is found to be essential for the lattice reconstruction. The charge-density wave results in a strong localization of the electronic states near the Fermi level and consequently in spin polarization, transforming the material into a magnetic semiconductor with enhanced electronic correlations. The combination of inherent spin polarization with a semiconducting nature distinguishes the monolayer fundamentally from the bulk compound as well as from other two-dimensional transition metal dichalcogenides. Monolayer T-phase TaS2 therefore has the potential to enable two-dimensional spintronics. © 2014 American Physical Society.

  14. Generation of Ta ions at high laser-power densities

    Czech Academy of Sciences Publication Activity Database

    Láska, Leoš; Jungwirth, Karel; Králiková, Božena; Krása, Josef; Pfeifer, Miroslav; Rohlena, Karel; Skála, Jiří; Ullschmied, Jiří; Badziak, J.; Parys, P.; Wolowski, J.; Woryna, E.

    2002-01-01

    Roč. 52, Suppl. D (2002), s. D283-D291 ISSN 0011-4626. [Plasma Physics and Technology. Prague, 10.06.2002-13.06.2002] Institutional research plan: CEZ:AV0Z1010921 Keywords : laser produced plasma * multiple charged Ta ions Subject RIV: BH - Optics, Masers, Lasers Impact factor: 0.311, year: 2002

  15. Limited Range Sesame EOS for Ta

    Energy Technology Data Exchange (ETDEWEB)

    Greeff, Carl William [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Crockett, Scott [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Rudin, Sven Peter [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Burakovsky, Leonid [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

    2017-03-30

    A new Sesame EOS table for Ta has been released for testing. It is a limited range table covering T ≤ 26, 000 K and ρ ≤ 37.53 g/cc. The EOS is based on earlier analysis using DFT phonon calculations to infer the cold pressure from the Hugoniot. The cold curve has been extended into compression using new DFT calculations. The present EOS covers expansion into the gas phase. It is a multi-phase EOS with distinct liquid and solid phases. A cold shear modulus table (431) is included. This is based on an analytic interpolation of DFT calculations.

  16. Nonstoichiometric control of tunnel-filling order, thermal expansion, and dielectric relaxation in tetragonal tungsten Bronzes Ba0.5-xTaO3-x.

    Science.gov (United States)

    Pan, Fengjuan; Li, Xiaohui; Lu, Fengqi; Wang, Xiaoming; Cao, Jiang; Kuang, Xiaojun; Véron, Emmanuel; Porcher, Florence; Suchomel, Matthew R; Wang, Jing; Allix, Mathieu

    2015-09-21

    Ordering of interpolated Ba(2+) chains and alternate Ta-O rows (TaO)(3+) in the pentagonal tunnels of tetragonal tungsten bronzes (TTB) is controlled by the nonstoichiometry in the highly nonstoichiometric Ba0.5-xTaO3-x system. In Ba0.22TaO2.72, the filling of Ba(2+) and (TaO)(3+) groups is partially ordered along the ab-plane of the simple TTB structure, resulting in a √2-type TTB superstructure (Pbmm), while in Ba0.175TaO2.675, the pentagonal tunnel filling is completely ordered along the b-axis of the simple TTB structure, leading to a triple TTB superstructure (P21212). Both superstructures show completely empty square tunnels favoring Ba(2+) conduction and feature unusual accommodation of Ta(5+) cations in the small triangular tunnels. In contrast with stoichiometric Ba6GaTa9O30, which shows linear thermal expansion of the cell parameters and monotonic decrease of permittivity with temperature within 100-800 K, these TTB superstructures and slightly nonstoichiometric simple TTB Ba0.4TaO2.9 display abnormally broad and frequency-dependent extrinsic dielectric relaxations in 10(3)-10(5) Hz above room temperature, a linear deviation of the c-axis thermal expansion around 600 K, and high dielectric permittivity ∼60-95 at 1 MHz at room temperature.

  17. Influence of lead oxide addition on LnTiTaO 6 (Ln = Ce, Pr and Nd)

    Indian Academy of Sciences (India)

    The effect of PbO addition on the structural, processing and microwave dielectric properties of LnTiTaO6 (Ln = Ce, Pr and Nd) ceramics are reported. Conventional solid state ceramic route was used for the preparation of samples. Phase pure LnTiTaO6 (Ln = Ce, Pr and Nd) ceramics are prepared at a calcination ...

  18. Synthesis and Characterization of K-Ta Mixed Oxides for Hydrogen Generation in Photocatalysis

    Directory of Open Access Journals (Sweden)

    Beata Zielińska

    2012-01-01

    Full Text Available K-Ta mixed oxides photocatalysts have been prepared by impregnation followed by calcination. The influence of the reaction temperature (450°C–900°C on the phase formation, crystal morphology, and photocatalytic activity in hydrogen generation of the produced materials was investigated. The detailed analysis has revealed that all products exhibit high crystallinity and irregular structure. Moreover, two different crystal structures of potassium tantalates such as KTaO3 and K2Ta4O11 were obtained. It was also found that the sample composed of KTaO3 and traces of unreacted Ta2O5 (annealed at 600°C exhibits the highest activity in the reaction of photocatalytic hydrogen generation. The crystallographic phases, optical and vibronic properties were examined by X-ray diffraction (XRD and diffuse reflectance (DR UV-vis and resonance Raman spectroscopic methods, respectively. Morphology and chemical composition of the produced samples were studied using a high-resolution transmission electron microscope (HR-TEM and an energy dispersive X-ray spectrometer (EDX as its mode.

  19. Characterization of a wheat (Triticum aestivum L.) expansin gene, TaEXPB23, involved in the abiotic stress response and phytohormone regulation.

    Science.gov (United States)

    Han, Yang yang; Li, Ai xiu; Li, Feng; Zhao, Mei rong; Wang, Wei

    2012-05-01

    Expansins are proteins that are generally accepted to be key regulators of cell wall extension and plant growth. We examined the expression pattern of TaEXPB23, a wheat (Triticum aestivum L.) expansin gene, under exogenous phytohormone and abiotic stress treatments. In addition, we evaluated its function in the tolerance to salt stress and high temperature (HT) by overexpressing it in transgenic tobacco plants. In subcellular localization assays, TaEXPB23 localized to the cell wall. Expression analysis demonstrated that the transcription pattern of TaEXPB23 corresponded to wheat coleoptile growth. Real-time RT-PCR analysis revealed that TaEXPB23 transcript expression was upregulated by exogenous methyl jasmonate (MeJA) and salt stress, but downregulated by exogenous gibberellins (GA₃), ethylene (ET), indole-3-acetic acid (IAA) and α-naphthlcetic acid (NAA). Overexpression of TaEXPB23 in tobacco (tabacum) conferred tolerance to salt stress by enhancing water retention ability (WRA) and decreasing osmotic potential (OP). However, transgenic plants overexpressing TaEXPB23 did not show any improvement in the tolerance to HT stress. These results suggested that TaEXPB23 is regulated by phytohormones and is involved in the regulation of salt stress tolerance. Copyright © 2012 Elsevier Masson SAS. All rights reserved.

  20. Investigation of the phase formation and dielectric properties of Bi{sub 7}Ta{sub 3}O{sub 18}

    Energy Technology Data Exchange (ETDEWEB)

    Chon, M.P. [Department of Chemistry, Faculty of Science, Universiti Putra Malaysia, 43400 Serdang, Selangor (Malaysia); Tan, K.B., E-mail: tankb@science.upm.my [Department of Chemistry, Faculty of Science, Universiti Putra Malaysia, 43400 Serdang, Selangor (Malaysia); Khaw, C.C. [Department of Mechanical and Material Engineering, Faculty of Engineering and Science, Universiti Tunku Abdul Rahman, 53300 Setapak, Kuala Lumpur (Malaysia); Zainal, Z.; Taufiq Yap, Y.H. [Department of Chemistry, Faculty of Science, Universiti Putra Malaysia, 43400 Serdang, Selangor (Malaysia); Chen, S.K. [Department of Physics, Faculty of Science, Universiti Putra Malaysia, 43400 Serdang, Selangor (Malaysia); Tan, P.Y. [Department of Chemistry, Faculty of Science, Universiti Putra Malaysia, 43400 Serdang, Selangor (Malaysia)

    2014-03-25

    Highlights: • Synthesis condition of Bi{sub 7}TaO{sub 3}O{sub 18} had been determined. • Recombination of intermediate BiTaO{sub 4} and Bi{sub 3}TaO{sub 7} phases are required for the Bi{sub 7}TaO{sub 3}O{sub 18} phase formation. • Stable material as confirmed by thermal and structural analyses. • Typical ferroelectric showing high dielectric constants and low losses. • Resonance and thermal activated polarisation processes are responsible for the excellent dielectric characteristic. -- Abstract: Polycrystalline Bi{sub 7}Ta{sub 3}O{sub 18} was synthesised at the firing temperature of 950 °C over 18 h via conventional solid state method. It crystallised in a monoclinic system with space group C2/m, Z = 4 similar to that reported diffraction pattern in the Inorganic Crystal Structure Database (ICSD), 1-89-6647. The refined lattice parameters were a = 34.060 (3) Å, b = 7.618 (9) Å, c = 6.647 (6) Å with α = γ = 90° and β = 109.210 (7), respectively. The intermediate phase was predominantly in high-symmetry cubic structure below 800 °C and finally evolved into a low-symmetry monoclinic structured, Bi{sub 7}Ta{sub 3}O{sub 18} at 950 °C. The sample contained grains of various shapes with different orientations in the size ranging from 0.33–22.70 μm. The elemental analysis showed the sample had correct stoichiometry with negligible Bi{sub 2}O{sub 3} loss. Bi{sub 7}Ta{sub 3}O{sub 18} was thermally stable and it exhibited a relatively high relative permittivity, 241 and low dielectric loss, 0.004 at room temperature, ∼30 °C and frequency of 1 MHz.

  1. TaHsfA6f is a transcriptional activator that regulates a suite of heat stress protection genes in wheat (Triticum aestivum L.) including previously unknown Hsf targets.

    Science.gov (United States)

    Xue, Gang-Ping; Drenth, Janneke; McIntyre, C Lynne

    2015-02-01

    Heat stress is a significant environmental factor adversely affecting crop yield. Crop adaptation to high-temperature environments requires transcriptional reprogramming of a suite of genes involved in heat stress protection. This study investigated the role of TaHsfA6f, a member of the A6 subclass of heat shock transcription factors, in the regulation of heat stress protection genes in Triticum aestivum (bread wheat), a poorly understood phenomenon in this crop species. Expression analysis showed that TaHsfA6f was expressed constitutively in green organs but was markedly up-regulated during heat stress. Overexpression of TaHsfA6f in transgenic wheat using a drought-inducible promoter resulted in up-regulation of heat shock proteins (HSPs) and a number of other heat stress protection genes that included some previously unknown Hsf target genes such as Golgi anti-apoptotic protein (GAAP) and the large isoform of Rubisco activase. Transgenic wheat plants overexpressing TaHsfA6f showed improved thermotolerance. Transactivation assays showed that TaHsfA6f activated the expression of reporter genes driven by the promoters of several HSP genes (TaHSP16.8, TaHSP17, TaHSP17.3, and TaHSP90.1-A1) as well as TaGAAP and TaRof1 (a co-chaperone) under non-stress conditions. DNA binding analysis revealed the presence of high-affinity TaHsfA6f-binding heat shock element-like motifs in the promoters of these six genes. Promoter truncation and mutagenesis analyses identified TaHsfA6f-binding elements that were responsible for transactivation of TaHSP90.1-A1 and TaGAAP by TaHsfA6f. These data suggest that TaHsfA6f is a transcriptional activator that directly regulates TaHSP, TaGAAP, and TaRof1 genes in wheat and its gene regulatory network has a positive impact on thermotolerance. © The Author 2014. Published by Oxford University Press on behalf of the Society for Experimental Biology.

  2. TiZrNbTaMo high-entropy alloy designed for orthopedic implants: As-cast microstructure and mechanical properties.

    Science.gov (United States)

    Wang, Shao-Ping; Xu, Jian

    2017-04-01

    Combining the high-entropy alloy (HEA) concept with property requirement for orthopedic implants, we designed a Ti 20 Zr 20 Nb 20 Ta 20 Mo 20 equiatomic HEA. The arc-melted microstructures, compressive properties and potentiodynamic polarization behavior in phosphate buffer solution (PBS) were studied in detail. It was revealed that the as-cast TiZrNbTaMo HEA consisted of dual phases with bcc structure, major bcc1 and minor bcc2 phases with the lattice parameters of 0.3310nm and 0.3379nm, respectively. As confirmed by nanoindentation tests, the bcc1 phase is somewhat harder and stiffer than the bcc2 phase. The TiZrNbTaMo HEA exhibited Young's modulus of 153GPa, Vickers microhardness of 4.9GPa, compressive yield strength of σ y =1390MPa and apparent plastic strain of ε p ≈6% prior to failure. Moreover, the TiZrNbTaMo HEA manifested excellent corrosion resistance in PBS, comparable to the Ti6Al4V alloy, and pitting resistance remarkably superior to the 316L SS and CoCrMo alloys. These preliminary advantages of the TiZrNbTaMo HEA over the current orthopedic implant metals in mechanical properties and corrosion resistance offer an opportunity to explore new orthopedic-implant alloys based on the TiZrNbTaMo concentrated composition. Copyright © 2016 Elsevier B.V. All rights reserved.

  3. Co-sputtered amorphous Nb–Ta, Nb–Zr and Ta–Zr coatings for corrosion protection of cyclotron targets for [{sup 18}F] production

    Energy Technology Data Exchange (ETDEWEB)

    Skliarova, Hanna, E-mail: Hanna.Skliarova@lnl.infn.it [National Institute of Nuclear Physics, Legnaro National Laboratories, Viale dell’Università, 2, 35020 Legnaro, Padua (Italy); University of Ferrara, Ferrara (Italy); Azzolini, Oscar, E-mail: Oscar.Azzolini@lnl.infn.it [National Institute of Nuclear Physics, Legnaro National Laboratories, Viale dell’Università, 2, 35020 Legnaro, Padua (Italy); Johnson, Richard R., E-mail: richard.johnson@teambest.com [BEST Cyclotron Systems Inc., 8765 Ash Street Unit 7, Vancouver, BC V6P 6T3 (Canada); Palmieri, Vincenzo, E-mail: Vincenzo.Palmieri@lnl.infn.it [National Institute of Nuclear Physics, Legnaro National Laboratories, Viale dell’Università, 2, 35020 Legnaro, Padua (Italy); University of Padua, Padua (Italy)

    2015-08-05

    Highlights: • Nb–Ta, Nb–Zr and Ta–Zr alloy films were deposited by co-sputtering. • Co-sputtered Nb–Zr and Nb–Ta alloy coatings had crystalline microstructures. • Diffusion barrier efficiency of Nb–Zr and Nb–Ta decreased with the increase of Nb %. • Co-sputtered Ta–Zr films with 30–73 at.% Ta were amorphous. • Sputtered amorphous Ta–Zr films showed superior diffusion barrier efficiency. - Abstract: Protective corrosion resistant coatings serve for decreasing the amount of ionic contaminants from Havar® entrance foils of the targets for [{sup 18}F] production. The corrosion damage of coated entrance foils is caused mainly by the diffusion of highly reactive products of water radiolysis through the protective film toward Havar® substrate. Since amorphous metal alloys (metallic glasses) are well-known to perform a high corrosion resistance, the glass forming ability, microstructure and diffusion barrier efficiency of binary alloys containing chemically inert Nb, Ta, Zr were investigated. Nb–Ta, Nb–Zr and Ta–Zr films of different alloy composition and ∼1.5 μm thickness were co-deposited by magnetron sputtering. Diffusion barrier efficiency tests used reactive aluminum underlayer and protons of acid solution and gallium atoms at elevated temperature as diffusing particles. Though co-sputtered Nb–Ta and Nb–Zr alloy films of different contents were crystalline, Ta–Zr alloy was found to form dense amorphous microstructures in a range of composition with 30–73% atomic Ta. The diffusion barrier efficiency of Nb–Zr and Nb–Ta alloy coatings decreased with increase of Nb content. The diffusion barrier efficiency of sputtered Ta–Zr alloy coatings increased with the transition from nanocrystalline columnar microstructure to amorphous for coatings with 30–73 at.% Ta.

  4. Highly active GaN-stabilized Ta{sub 3}N{sub 5} thin-film photoanode for solar water oxidation

    Energy Technology Data Exchange (ETDEWEB)

    Zhong, Miao; Hisatomi, Takashi; Sasaki, Yutaka; Nakabayashi, Mamiko; Shibata, Naoya; Nishiyama, Hiroshi; Katayama, Masao; Yamada, Taro; Domen, Kazunari [School of Engineering, the University of Tokyo (Japan); Japan Technological Research Association of Artificial Photosynthetic Chemical Process, Tokyo (Japan); Suzuki, Sayaka; Teshima, Katsuya [Faculty of Engineering, Shinshu University, Nagano (Japan)

    2017-04-18

    Ta{sub 3}N{sub 5} is a very promising photocatalyst for solar water splitting because of its wide spectrum solar energy utilization up to 600 nm and suitable energy band position straddling the water splitting redox reactions. However, its development has long been impeded by poor compatibility with electrolytes. Herein, we demonstrate a simple sputtering-nitridation process to fabricate high-performance Ta{sub 3}N{sub 5} film photoanodes owing to successful synthesis of the vital TaO{sub δ} precursors. An effective GaN coating strategy is developed to remarkably stabilize Ta{sub 3}N{sub 5} by forming a crystalline nitride-on-nitride structure with an improved nitride/electrolyte interface. A stable, high photocurrent density of 8 mA cm{sup -2} was obtained with a CoPi/GaN/Ta{sub 3}N{sub 5} photoanode at 1.2 V{sub RHE} under simulated sunlight, with O{sub 2} and H{sub 2} generated at a Faraday efficiency of unity over 12 h. Our vapor-phase deposition method can be used to fabricate high-performance (oxy)nitrides for practical photoelectrochemical applications. (copyright 2017 Wiley-VCH Verlag GmbH and Co. KGaA, Weinheim)

  5. Study of radionuclides created by 181Ta(γ,xn yp) reactions for bremsstrahlung photons produced by 150-MeV electrons

    International Nuclear Information System (INIS)

    Miller, M.A.; Dickens, J.K.

    1991-12-01

    Ten radionuclides, including isomers, from 172 Ta to 180 Ta and 180m Hf were produced by photon interactions with a sample of elemental tantalum and measured by counting photons using a high-resolution detection system. Relative yields of these radionuclides were obtained. In addition, precision half lives were obtained for 175,176,180 Ta and 180m Hf. Those obtained for the three Ta isotopes agree with previously reported values. For 180m Hf, the present measurements resulted in a half life determination of 6.05±0.06 hr, or about 10% longer than the currently adopted value for this half life

  6. A study of Love wave devices in ZnO/Quartz and ZnO/LiTaO3 structures

    International Nuclear Information System (INIS)

    Chang, R.-C.; Chu, S.-Y.; Hong, C.-S.; Chuang, Y.-T.

    2006-01-01

    Love wave devices are very promising for sensing applications because of high sensitivity. In this paper, ZnO thin films doped with lithium (Li) and magnesium (Mg) were deposited on the 42 o 45' ST-cut quartz and 36 o YX-LiTaO 3 substrates by RF magnetron sputtering technique. XRD, SEM, and AFM measurements investigated characteristics of the films. Under different conditions such as doping content, layer thickness, and substrate temperature, the phase velocity, temperature coefficient of frequency, electromechanical coupling coefficient and sensitivity of Love wave devices in ZnO/Quartz and ZnO/LiTaO 3 structures are presented. The maximum sensitivities of ZnO/Quartz and ZnO/LiTaO 3 are much higher than the SiO 2 /Quartz and SiO 2 /LiTaO 3 structures reported

  7. Observations on Si-based micro-clusters embedded in TaN thin film deposited by co-sputtering with oxygen contamination

    Energy Technology Data Exchange (ETDEWEB)

    Lee, Young Mi [Beamline Division, Pohang Accelerator Laboratory, POSTECH, Pohang, 305-764 (Korea, Republic of); Jung, Min-Sang; Choi, Duck-Kyun, E-mail: duck@hanyang.ac.kr, E-mail: mcjung@oist.jp [Department of Materials Science and Engineering, Hanyang University, Seoul 133-791 (Korea, Republic of); Jung, Min-Cherl, E-mail: duck@hanyang.ac.kr, E-mail: mcjung@oist.jp [Energy Materials and Surface Sciences Unit, Okinawa Institute of Science and Technology Graduate University, Okinawa, 904-0495 (Japan)

    2015-08-15

    Using scanning electron microscopy (SEM) and high-resolution x-ray photoelectron spectroscopy with the synchrotron radiation we investigated Si-based micro-clusters embedded in TaSiN thin films having oxygen contamination. TaSiN thin films were deposited by co-sputtering on fixed or rotated substrates and with various power conditions of TaN and Si targets. Three types of embedded micro-clusters with the chemical states of pure Si, SiO{sub x}-capped Si, and SiO{sub 2}-capped Si were observed and analyzed using SEM and Si 2p and Ta 4f core-level spectra were derived. Their different resistivities are presumably due to the different chemical states and densities of Si-based micro-clusters.

  8. Observations on Si-based micro-clusters embedded in TaN thin film deposited by co-sputtering with oxygen contamination

    Directory of Open Access Journals (Sweden)

    Young Mi Lee

    2015-08-01

    Full Text Available Using scanning electron microscopy (SEM and high-resolution x-ray photoelectron spectroscopy with the synchrotron radiation we investigated Si-based micro-clusters embedded in TaSiN thin films having oxygen contamination. TaSiN thin films were deposited by co-sputtering on fixed or rotated substrates and with various power conditions of TaN and Si targets. Three types of embedded micro-clusters with the chemical states of pure Si, SiOx-capped Si, and SiO2-capped Si were observed and analyzed using SEM and Si 2p and Ta 4f core-level spectra were derived. Their different resistivities are presumably due to the different chemical states and densities of Si-based micro-clusters.

  9. IFNG polymorphism (+874 T>A is not a risk factor for cervical cancer

    Directory of Open Access Journals (Sweden)

    Ani Melani Maskoen

    2013-04-01

    Full Text Available Introduction Cervical cancer cases are rising and many women are infected with human papillomavirus (HPV. Interferon gamma (IFN-ã is one of the key regulatory cytokines that influence the HPV clearance. The production and the function of IFN-ã may impaired by the defect of the IFNG gene leading to the cervical malignant progression. This study aimed to examine the association between IFNG+874 T>A polymorphism and cervical cancer in women Methods In a case-control study design, consecutive untreated women with cervical cancer who showed for the first time in Hasan Sadikin Hospital Bandung were enrolled (n=98 and for controls women who came for PAP smear (n = 81. Controls were not matched in ages and ethnicities. DNA extracted from blood was amplified by amplification refractory mutation system - polymerase chain reaction method (ARMS – PCR to detect IFNG+874 T>A polymorphism. Results The distribution of IFNG genotypes TT, TA and AA for women with cervical cancer who met the inclusion criteria (n= 64 and with negative intraepithelial lesion or malignancy (n=42 were 14.1%, 50.0%, 35.9% and 7.1%, 52.4%, 40.5%, respectively. No significant differences could be observed between both groups (p=0.64. Stratifying the cervical cancer women into a group of squamous cell carcinoma (n = 54 revealed no statistical different. Conclusion IFNG +874 T>A polymorphismseems not to contribute in susceptibility to cervical cancer. Identification of other variants in IFNG gene signaling and its role in the development of cervical cancer diseases need to be further examined.

  10. Preparation of high laser-induced damage threshold Ta{sub 2}O{sub 5} films

    Energy Technology Data Exchange (ETDEWEB)

    Xu, Cheng, E-mail: xucheng@cumt.edu.cn [School of Materials Science and Engineering, China University of Mining and Technology, Xuzhou 221116 (China); Yi, Peng; Fan, Heliang; Qi, Jianwei; Yang, Shuai; Qiang, Yinghuai; Liu, Jiongtian [School of Materials Science and Engineering, China University of Mining and Technology, Xuzhou 221116 (China); Li, Dawei [Key Laboratory of High Power Laser Materials, Shanghai Institute of Optics and Fine Mechanics, Chinese Academy of Sciences, Shanghai 201800 (China)

    2014-08-01

    High laser-induced damage threshold (LIDT) Ta{sub 2}O{sub 5} films were prepared by the sol–gel method using TaCl{sub 5} as a new precursor. The optical properties, surface morphologies, chemical composition, absorption and LIDT of the films were investigated. The results showed that the transparent and homogenous Ta{sub 2}O{sub 5} films had small surface roughness, low absorption and high LIDT even with large number of layers. The maximum LIDT at 1064 nm and 12 ns of the films was 24.8 J/cm{sup 2}. The ion chromatograph and Fourier transform infrared spectrum were used to reveal the functions of the addition of H{sub 2}O{sub 2} in the sol formation. It was shown that H{sub 2}O{sub 2} had two important functions, which were the decrease of Cl element content and the rapid generation of tantalum oxide. The high LIDT achieved was mainly due to the nearly free of defects in the films.

  11. Deposition and characterization of TaAIN thin films by reactive magnetron sputtering; Deposicao e caracterizacao de filmes finos de TaAIN depositados por magnetron sputtering

    Energy Technology Data Exchange (ETDEWEB)

    Oliveira, G.B.; Fernandez, D.R.; Fontes Junior, A.S.; Felix, L.C.; Tentardini, E.K. [Universidade Federal de Sergipe (UFS), Sao Cristovao, SE (Brazil). Departamento de Ciencia e Engenharia de Materiais; Hubler, R. [Pontificia Universidade Catolica do Rio Grande do Sul (PUC-RS), RS (Brazil); Silva Junior, A.H. da, E-mail: brito-g@hotmail.com [Universidade Federal do Rio Grande do Sul (UFRGS), RS (Brazil)

    2016-07-01

    Phase stability, oxidation resistance and great mechanical properties are the main objectives when synthesizing protective coatings. The tantalum nitride (TaN) has aroused interest because of its high temperature stability, chemical inertness and thermal conductivity. However, it has a low hardness value when compared to other coatings. Researches has shown that one way to improvements in the properties of a thin film is by adding other elements in the deposition process. Therefore, the objective of this study was to deposit thin films of TaAlN by magnetron sputtering, changing the aluminum concentration of 2, 5, 7, to 14%. Then the coatings were characterized by EDS, RBS, GIXRD and nanohardness. In this study was found that the aluminum deposited did not change the oxidation resistance of the coating, and the highest value of hardness was 28 GPa for the sample with 14 at.%. (author)

  12. Multifilamentary superconducting (NbTa)-Sn composite wire by solid-liquid reaction for possible application above 20 tesla

    International Nuclear Information System (INIS)

    Hong, M.; Hull, G.W. Jr.; Fuchs, E.O.; Holthuis, J.T.

    1983-01-01

    Nb alloyed with Ta was employed in fabricating multifilamentary composite wires of (NbTa)-Sn using the liquid-infiltration process. The superconducting A15 phase was formed with subsequent heat treatments at 800-950 0 C by the solid-liquid reaction. High inductive Tsub(c)'s of 18.2 K with sharp transition width ( 4 A/cm 2 at 2O T and 4.2 K were obtained. It was found that 2 wt.% Ta in the Nb was sufficient in the enhancement of the overall Jsub(c) at the high fields and in increasing the Hsub(c2) (4.2 K) to 25 T. (Auth.)

  13. Multifilamentary superconducting (NbTa)-Sn composite wire by solid-liquid reaction for possible application above 20 tesla

    International Nuclear Information System (INIS)

    Hong, M.; Hull, G.W. Jr.; Fuchs, E.O.; Holthuis, J.T.

    1983-01-01

    Nb alloyed with Ta was employed in fabricating multifilamentary composite wires of (NbTa)-Sn using the liquid-infiltration process. The superconducting A15 phase was formed with subsequent heat treatments at 800-950 0 C by the solid-liquid reaction. High inductive Tsub(c)'s of 18.2 K with sharp transition width ( 4 A/cm 2 at 20 T and 4.2 K were obtained. It was found that 2 wt.% Ta in the Nb was sufficient in the enhancement of the overall Jsub(c) at the high fields and in increasing the Hsub(c2) (4.2 K) to 25 T. (orig.)

  14. 17 CFR 249.619 - Form TA-Y2K, information required of transfer agents pursuant to section 17 of the Securities...

    Science.gov (United States)

    2010-04-01

    ... 17 Commodity and Securities Exchanges 3 2010-04-01 2010-04-01 false Form TA-Y2K, information... Certain Exchange Members, Brokers, and Dealers § 249.619 Form TA-Y2K, information required of transfer... affecting Form TA-Y2K, see the List of CFR Sections Affected, which appears in the Finding Aids section of...

  15. Wheat TaRab7 GTPase is part of the signaling pathway in responses to stripe rust and abiotic stimuli.

    Directory of Open Access Journals (Sweden)

    Furong Liu

    Full Text Available Small GTP-binding proteins function as regulators of specific intercellular fundamental biological processes. In this study, a small GTP-binding protein Rab7 gene, designated as TaRab7, was identified and characterized from a cDNA library of wheat leaves infected with Puccinia striiformis f. sp. tritici (Pst the wheat stripe rust pathogen. The gene was predicted to encode a protein of 206 amino acids, with a molecular mass of 23.13 KDa and an isoeletric point (pI of 5.13. Further analysis revealed the presence of a conserved signature that is characteristic of Rab7, and phylogenetic analysis demonstrated that TaRab7 has the highest similarity to a small GTP binding protein gene (BdRab7-like from Brachypodium distachyon. Quantitative real-time PCR assays revealed that the expression of TaRab7 was higher in the early stage of the incompatible interactions between wheat and Pst than in the compatible interaction, and the transcription level of TaRab7 was also highly induced by environmental stress stimuli. Furthermore, knocking down TaRab7 expression by virus induced gene silencing enhanced the susceptibility of wheat cv. Suwon 11 to an avirulent race CYR23. These results imply that TaRab7 plays an important role in the early stage of wheat-stripe rust fungus interaction and in stress tolerance.

  16. Počítačová hra s prvky umělé inteligence

    OpenAIRE

    Serédi, Silvester

    2010-01-01

    Bakalářská práce se zabývá problematikou umělé inteligence v počítačové hře. V práci je uveden návrh dvourozměrné počítačové hry pro dva hráče, kde jednoho z nich může řídit počítač. Hlavní úlohou bylo vytvoření hry s jednoduchým uživatelským rozhraním, se zaměřením na umělou inteligenci soupeře. This Bachelor's thesis is focused on artificial intelligence in computer games. It introduces the design of a two-dimensional computer game for two players of which one can be computer-controlled....

  17. Microstructure, mechanical behavior and biocompatibility of powder metallurgy Nb-Ti-Ta alloys as biomedical material.

    Science.gov (United States)

    Liu, Jue; Chang, Lin; Liu, Hairong; Li, Yongsheng; Yang, Hailin; Ruan, Jianming

    2017-02-01

    Microstructures, mechanical properties, apatite-forming ability and in vitro experiments were studied for Nb-25Ti-xTa (x=10, 15, 20, 25, 35at.%) alloys fabricated by powder metallurgy. It is confirmed that the alloys could achieve a relative density over 80%. Meanwhile, the increase in Ta content enhances the tensile strength, elastic modulus and hardness of the as-sintered alloys. When increasing the sintering temperatures, the microstructure became more homogeneous for β phase, resulting in a decrease in the modulus and strength. Moreover, the alloys showed a good biocompatibility due to the absence of cytotoxic elements, and were suitable for apatite formation and cell adhesion. In conclusion, Nb-25Ti-xTa alloys are potentially useful in biomedical applications with their mechanical and biological properties being evaluated in this work. Copyright © 2016 Elsevier B.V. All rights reserved.

  18. Optimizing AlF{sub 3} atomic layer deposition using trimethylaluminum and TaF{sub 5}: Application to high voltage Li-ion battery cathodes

    Energy Technology Data Exchange (ETDEWEB)

    Jackson, David H. K., E-mail: david.jackson@wisc.edu; Kuech, Thomas F. [Materials Science Program, University of Wisconsin–Madison, Madison, Wisconsin 53706 and Department of Chemical and Biological Engineering, University of Wisconsin–Madison, Madison, Wisconsin 53706 (United States); Laskar, Masihhur R.; Ellis, Ryan G. [Department of Chemical and Biological Engineering, University of Wisconsin–Madison, Madison, Wisconsin 53706 (United States); Fang, Shuyu; Hamers, Robert J. [Department of Chemistry, University of Wisconsin–Madison, Madison, Wisconsin 53706 (United States); Xu, Shenzhen; Li, Xiaoqing; Morgan, Dane [Department of Materials Science and Engineering, University of Wisconsin–Madison, Madison, Wisconsin 53706 (United States); Dreibelbis, Mark [Core R& D, Inorganic Materials and Heterogeneous Catalysis, The Dow Chemical Company, Midland, Michigan 48674 (United States); Babcock, Susan E. [Materials Science Program, University of Wisconsin–Madison, Madison, Wisconsin 53706 and Department of Materials Science and Engineering, University of Wisconsin–Madison, Madison, Wisconsin 53706 (United States); Mahanthappa, Mahesh K. [Materials Science Program, University of Wisconsin–Madison, Madison, Wisconsin 53706 and Department of Chemistry, University of Wisconsin–Madison, Madison, Wisconsin 53706 (United States)

    2016-05-15

    Atomic layer deposition (ALD) of conformal AlF{sub 3} coatings onto both flat silicon substrates and high-voltage LiNi{sub 0.5}Mn{sub 0.3}Co{sub 0.2}O{sub 2} (NMC) Li-ion battery cathode powders was investigated using a Al(CH{sub 3}){sub 3}/TaF{sub 5} precursor combination. This optimized approach employs easily handled ALD precursors, while also obviating the use of highly toxic HF(g). In studies conducted on planar Si wafers, the film's growth mode was dictated by a competition between the desorption and decomposition of Ta reaction byproducts. At T ≥ 200 °C, a rapid decomposition of the Ta reaction byproducts to TaC led to continuous deposition and high concentrations of TaC in the films. A self-limited ALD growth mode was found to occur when the deposition temperature was reduced to 125 °C, and the TaF{sub 5} exposures were followed by an extended purge. The lower temperature process suppressed conversion of TaF{sub x}(CH{sub 3}){sub 5−x} to nonvolatile TaC, and the long purges enabled nearly complete TaF{sub x}(CH{sub 3}){sub 5−x} desorption, leaving behind the AlF{sub 3} thin films. NMC cathode powders were coated using these optimized conditions, and coin cells employing these coated cathode particles exhibited significant improvements in charge capacity fade at high discharge rates.

  19. Variable substrate temperature deposition of CoFeB film on Ta for manipulating the perpendicular coercive forces

    Science.gov (United States)

    Lakshmanan, Saravanan; Rao, Subha Krishna; Muthuvel, Manivel Raja; Chandrasekaran, Gopalakrishnan; Therese, Helen Annal

    2017-08-01

    Magnetization of Ta/CoFeB/Ta trilayer films with thick layer of CoFeB deposited under different substrate temperatures (Ts) via ultra-high vacuum DC sputtering technique has been measured with the applied magnetic field parallel and perpendicular to the plane of the film respectively to study the perpendicular coercive forces of the film. The samples were further analyzed for its structural, topological, morphological, and electrical transport properties. The core chemical states for the elements present in the CoFeB thin film were analyzed by XPS studies. Magnetization studies reveal the existence of perpendicular coercive forces in CoFeB films deposited only at certain temperatures such as RT, 450 °C, 475 °C and 500 °C. CoFeB film deposited at 475 °C exhibited a maximum coercivity of 315 Oe and a very low saturation magnetization (Ms) of 169 emu/cc in perpendicular direction. This pronounced effect in perpendicular coercive forces observed for CoFeB475 could be attributed to the effect of temperature in enhancing the crystallization of the film at the Ta/CoFeB interfaces. However at temperatures higher than 475 °C the destruction of the Ta/CoFeB interface due to intermixing of Ta and CoFeB results in the disappearance of magnetic anisotropy.

  20. Confirmation of Non-Impacted Status (TA16-280 Complex)

    Energy Technology Data Exchange (ETDEWEB)

    Ruedig, Elizabeth [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

    2017-12-07

    EPC-ES finds that the materials associated with TA16-280 complex (see Figure 1) are candidates for release to the public for recycle or as sanitary/commercial waste. This finding is consistent with the requirements of DOE Order 458.1 Radiation Protection of the Public and the Environment and LANL Policy 412 Environmental Radiation Protection.