Electrochemical corrosion testing of metal waste forms

International Nuclear Information System (INIS)

Abraham, D. P.; Peterson, J. J.; Katyal, H. K.; Keiser, D. D.; Hilton, B. A.

1999-01-01

Electrochemical corrosion tests have been conducted on simulated stainless steel-zirconium (SS-Zr) metal waste form (MWF) samples. The uniform aqueous corrosion behavior of the samples in various test solutions was measured by the polarization resistance technique. The data show that the MWF corrosion rates are very low in groundwaters representative of the proposed Yucca Mountain repository. Galvanic corrosion measurements were also conducted on MWF samples that were coupled to an alloy that has been proposed for the inner lining of the high-level nuclear waste container. The experiments show that the steady-state galvanic corrosion currents are small. Galvanic corrosion will, hence, not be an important mechanism of radionuclide release from the MWF alloys

Materials Characterization Center meeting on impact testing of waste forms. Summary report

International Nuclear Information System (INIS)

Merz, M.D.; Atteridge, D.; Dudder, G.

1981-10-01

A meeting was held on March 25-26, 1981 to discuss impact test methods for waste form materials to be used in nuclear waste repositories. The purpose of the meeting was to obtain guidance for the Materials Characterization Center (MCC) in preparing the MCC-10 Impact Test Method to be approved by the Materials Review Board. The meeting focused on two essential aspects of the test method, namely the mechanical process, or impact, used to effect rapid fracture of a waste form and the analysis technique(s) used to characterize particulates generated by the impact

Testing of high-level waste forms under repository conditions

International Nuclear Information System (INIS)

Mc Menamin, T.

1989-01-01

The workshop on testing of high-level waste forms under repository conditions was held on 17 to 21 October 1988 in Cadarache, France, and sponsored by the Commission of the European Communities (CEC), the Commissariat a l'energie atomique (CEA) and the Savannah River Laboratory (US DOE). Participants included representatives from Australia, Belgium, Denmark, France, Germany, Italy, Japan, the Netherlands, Sweden, Switzerland, The United Kingdom and the United States. The first part of the conference featured a workshop on in situ testing of simulated nuclear waste forms and proposed package components, with an emphasis on the materials interface interactions tests (MIIT). MIIT is a sevent-part programme that involves field testing of 15 glass and waste form systems supplied by seven countries, along with potential canister and overpack materials as well as geologic samples, in the salt geology at the Waste Isolation Pilot Plant (WIPP) in Carlsbad, New Mexico, USA. This effort is still in progress and these proceedings document studies and findings obtained thus far. The second part of the meeting emphasized multinational experimental studies and results derived from repository systems simulation tests (RSST), which were performed in granite, clay and salt environments

Metal waste forms from the electrometallurgical treatment of spent nuclear fuel

International Nuclear Information System (INIS)

Abraham, D.P.; McDeavitt, S.M.; Park, J.

1996-01-01

Stainless steel-zirconium alloys are being developed for the disposal of radioactive metal isotopes isolated using an electrometallurgical treatment technique to treat spent nuclear fuel. The nominal waste forms are stainless steel-15 wt% zirconium alloy and zirconium-8 wt% stainless steel alloy. These alloys are generated in yttria crucibles by melting the starting materials at 1,600 C under an argon atmosphere. This paper discusses the microstructures, corrosion and mechanical test results, and thermophysical properties of the metal waste form alloys

Materials characterization center workshop on the irradiation effects in nuclear waste forms

International Nuclear Information System (INIS)

Roberts, F.P.; Turcotte, R.P.; Weber, W.J.

1981-01-01

The Workshop on Irradiation Effects in Nuclear Waste Forms sponsored by the Materials Characterization Center (MCC) brought together experts in radiation damage in materials and waste-management technology to review the problems associated with irradiation effects on waste-form integrity and to evaluate standard methods for generating data to be included in the Nuclear Waste Materials Handbook. The workshop reached the following conclusions: the concept of Standard Test for the Effects of Alpha-Decay in Nuclear Waste Solids, (MCC-6) for evaluating the effects of alpha decay is valid and useful, and as a result of the workshop, modifications to the proposed procedure will be incorpoated in a revised version of MCC-6; the MCC-6 test is not applicable to the evaluation of radiation damage in spent fuel; plutonium-238 is recommended as the dopant for transuranic and defense high-level waste forms, and when high doses are required, as in the case of commercial high-level waste forms, 244 Cm can be used; among the important property changes caused by irradiation are those that lead to greater leachability, and additionally, radiolysis of the leachant may increase leach rates; research is needed in this area; ionization-induced changes in physical properties can be as important as displacement damage in some materials, and a synergism is also likely to exist from the combined effects of ionization and displacement damage; and the effect of changing the temperature and dose rates on property changes induced by radiation damage needs to be determined

Crystallization behavior of nuclear waste forms

International Nuclear Information System (INIS)

Rusin, J.M.; Lokken, R.O.; May, R.P.; Wald, J.W.

1981-09-01

Several waste form options have been or are being developed for the immobilization of high-level wastes. The final selection of a waste form must take into consideration both waste form product as well as process factors. Crystallization behavior has an important role in nuclear waste form technology. For glass or vitreous waste forms, crystallization is generally controlled to a minimum by appropriate glass formulation and heat treatment schedules. With glass ceramic waste forms, crystallization is essential to convert glass products to highly crystalline waste forms with a minimum residual glass content. In the case of ceramic waste forms, additives and controlled sintering schedules are used to contain the radionuclides in specific tailored crystalline phases

Nuclear Fuel Test Rod Fabrication for Data Acquisition Test

International Nuclear Information System (INIS)

Joung, Chang-Young; Hong, Jin-Tae; Kim, Ka-Hye; Huh, Sung-Ho

2014-01-01

A nuclear fuel test rod must be fabricated with precise welding and assembly technologies, and confirmed for their soundness. Recently, we have developed various kinds of processing systems such as an orbital TIG welding system, a fiber laser welding system, an automated drilling system and a helium leak analyzer, which are able to fabricate the nuclear fuel test rods and rigs, and keep inspection systems to confirm the soundness of the nuclear fuel test rods and rids. The orbital TIG welding system can be used with two kinds of welding methods. One can perform the round welding for end-caps of a nuclear fuel test rod by an orbital head mounted in a low-pressure chamber. The other can do spot welding for a pin-hole of a nuclear fuel test rod in a high-pressure chamber to fill up helium gas of high pressure. The fiber laser welding system can weld cylindrical and 3 axis samples such as parts of a nuclear fuel test rod and instrumentation sensors which is moved by an index chuck and a 3 axis (X, Y, Z) servo stage controlled by the CNC program. To measure the real-time temperature change at the center of the nuclear fuel during the irradiation test, a thermocouple should be instrumented at that position. Therefore, a hole needs to be made at the center of fuel pellet to instrument the thermocouple. An automated drilling system can drill a fine hole into a fuel pellet without changing tools or breaking the work-piece. The helium leak analyzer (ASM-380 model of DEIXEN Co.) can check the leak of the nuclear fuel test rod filled with helium gas. This paper describes not only the assembly and fabrication methods used by the process systems, but also the results of the data acquisition test for the nuclear fuel test rod. A nuclear fuel test rod for the data acquisition test was fabricated using the welding and assembling echnologies acquired from previous tests

Nuclear Fuel Test Rod Fabrication for Data Acquisition Test

Energy Technology Data Exchange (ETDEWEB)

Joung, Chang-Young; Hong, Jin-Tae; Kim, Ka-Hye; Huh, Sung-Ho [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

2014-10-15

A nuclear fuel test rod must be fabricated with precise welding and assembly technologies, and confirmed for their soundness. Recently, we have developed various kinds of processing systems such as an orbital TIG welding system, a fiber laser welding system, an automated drilling system and a helium leak analyzer, which are able to fabricate the nuclear fuel test rods and rigs, and keep inspection systems to confirm the soundness of the nuclear fuel test rods and rids. The orbital TIG welding system can be used with two kinds of welding methods. One can perform the round welding for end-caps of a nuclear fuel test rod by an orbital head mounted in a low-pressure chamber. The other can do spot welding for a pin-hole of a nuclear fuel test rod in a high-pressure chamber to fill up helium gas of high pressure. The fiber laser welding system can weld cylindrical and 3 axis samples such as parts of a nuclear fuel test rod and instrumentation sensors which is moved by an index chuck and a 3 axis (X, Y, Z) servo stage controlled by the CNC program. To measure the real-time temperature change at the center of the nuclear fuel during the irradiation test, a thermocouple should be instrumented at that position. Therefore, a hole needs to be made at the center of fuel pellet to instrument the thermocouple. An automated drilling system can drill a fine hole into a fuel pellet without changing tools or breaking the work-piece. The helium leak analyzer (ASM-380 model of DEIXEN Co.) can check the leak of the nuclear fuel test rod filled with helium gas. This paper describes not only the assembly and fabrication methods used by the process systems, but also the results of the data acquisition test for the nuclear fuel test rod. A nuclear fuel test rod for the data acquisition test was fabricated using the welding and assembling echnologies acquired from previous tests.

Decades of nuclear testing

International Nuclear Information System (INIS)

Miettinen, J.K.

1995-01-01

The United States carried out the world's first nuclear test in 1945. The test marked the beginning of an arms race between the great powers that lasted for decades. Innumerable nuclear test explosions were detonated to test and refine the weapons. The arms race picked up speed in the 1950s and culminated in 1958, when the United States detonated 77 and the Soviet Union 35 nuclear explosions. This was followed by the first pause in nuclear testing, brought about through the efforts of the Pugwash organisation consisting of the world's foremost scientists. Finland, too, received its share of the radioactive fallout coming from atmospheric nuclear explosions. Rain water samples have been studied for radioactivity in Finland since the mid-1950s. The first studies to determine the internal radiation doses caused by radioactive substances in man were conducted in the late 1950s by measuring cesium and strontium contents in grass and in milk. The efficiency of research and radiation monitoring improved in the 1960s, which was also a time when training in the sector developed rapidly. In consequence, when the accident in Chernobyl took place Finland had already gained valuable experience needed for rapid determination of unexpected fallout. (orig.) (3 figs.)

Experiences with drug testing at a nuclear power plant

International Nuclear Information System (INIS)

Ray, H.B.

1987-01-01

After more than 2 yr of operation of a drug testing program at the San Onofre nuclear power plant site, the Southern California Edison Co. has had a number of experiences and lessons considered valuable. The drug testing program at San Onofre, implemented in September of 1984, continues in essentially the same form today. Prior to describing the program, the paper reviews several underlying issues that believed to be simultaneously satisfied by the program: trustworthiness, fitness and safety, public trust, and privacy and search. The overall drug testing program, periodic drug monitoring program, and unannounced drug testing program are described. In addition to the obvious features of a good drug testing program, which are described in the EEI guide, it is essential to consider such issues as the stated program rationale, employee relations, and disciplinary action measures when contemplating or engaging in drug testing at nuclear power plants

Results after ten years of field testing low-level radioactive waste forms using lysimeters

International Nuclear Information System (INIS)

McConnell, J.W. Jr.; Rogers, R.D.; Jastrow, J.D.; Sanford, W.E.; Larsen, I.L.; Sullivan, T.M.

1995-01-01

The Field Lysimeter Investigations: Low-Level Waste Data Base Development Program is obtaining information on the performance of radioactive waste forms. Ion-exchange resins from a commercial nuclear power station were solidified into waste forms using portland cement and vinyl esterstyrene. These waste forms are being tested to: (a) obtain information on performance of waste forms in typical disposal environments, (b) compare field results with bench leach studies, (c) develop a low-level waste data base for use in performance assessment source term calculations, and (d) apply the DUST computer code to compare predicted cumulative release to actual field data. The program, funded by the Nuclear Regulatory Commission (NRC), includes observed radionuclide releases from waste forms in field lysimeters. The purpose of this paper is to present the experimental results of two lysimeter arrays over 10 years of operation, and to compare those results to bench test results and to DUST code predicted releases. Further analysis of soil cores taken to define the observed upward migration of radionuclides in one lysimeter is also presented

Nuclear Energy Assessment Battery. Form C.

Science.gov (United States)

Showers, Dennis Edward

This publication consists of a nuclear energy assessment battery for secondary level students. The test contains 44 multiple choice items and is organized into four major sections. Parts include: (1) a knowledge scale; (2) attitudes toward nuclear energy; (3) a behaviors and intentions scale; and (4) an anxiety scale. Directions are provided for…

NNWSI waste form testing at Argonne National Laboratory

International Nuclear Information System (INIS)

Bates, J.K.; Gerding, T.J.; Abrajano, T.A. Jr.; Ebert, W.L.; Mazer, J.J.

1988-11-01

The Nevada Nuclear Waste Storage Investigation (NNWSI) Project is investigating the tuff beds of Yucca Mountain, Nevada, as a potential location for a high-level radioactive waste repository. As part of the waste package development portion of this project, experiments are being performed by the Chemical Technology Division of Argonne National Laboratory to study the behavior of the waste form under anticipated repository conditions. These experiments include the development and performance of a test to measure waste form behavior in unsaturated conditions and the performance of experiments designed to study the behavior of waste package components in an irradiated environment. Previous reports document developments in these areas through 1986. This report summarizes progress during the period January--June 1987, 19 refs., 17 figs., 20 tabs

Nuclear waste forms for actinides

Science.gov (United States)

Ewing, Rodney C.

1999-01-01

The disposition of actinides, most recently 239Pu from dismantled nuclear weapons, requires effective containment of waste generated by the nuclear fuel cycle. Because actinides (e.g., 239Pu and 237Np) are long-lived, they have a major impact on risk assessments of geologic repositories. Thus, demonstrable, long-term chemical and mechanical durability are essential properties of waste forms for the immobilization of actinides. Mineralogic and geologic studies provide excellent candidate phases for immobilization and a unique database that cannot be duplicated by a purely materials science approach. The “mineralogic approach” is illustrated by a discussion of zircon as a phase for the immobilization of excess weapons plutonium. PMID:10097054

Automated Test-Form Generation

Science.gov (United States)

van der Linden, Wim J.; Diao, Qi

2011-01-01

In automated test assembly (ATA), the methodology of mixed-integer programming is used to select test items from an item bank to meet the specifications for a desired test form and optimize its measurement accuracy. The same methodology can be used to automate the formatting of the set of selected items into the actual test form. Three different…

A comprehensive nuclear test ban

International Nuclear Information System (INIS)

1985-01-01

The conclusion of a comprehensive nuclear test ban is of critical importance for the future of arms limitation and disarmament. As the 1980 report of the Secretary-General concluded, a comprehensive nuclear test ban is regarded as the first and most urgent step towards the cessation of the nuclear arms race and, in particular, of its qualitative aspects. It could serve as an important measure for the non-proliferation of nuclear weapons, both vertical and horizontal. It would have a major arms limitation impact in that it would make it difficult, if not impossible, to develop new designs of nuclear weapons and would also place constraints on the modification of existing weapon designs. The permanent cessation of all nuclear-weapon tests has long been sought by the world community and its achievement would be an event of great international significance

Integrating Test-Form Formatting into Automated Test Assembly

Science.gov (United States)

Diao, Qi; van der Linden, Wim J.

2013-01-01

Automated test assembly uses the methodology of mixed integer programming to select an optimal set of items from an item bank. Automated test-form generation uses the same methodology to optimally order the items and format the test form. From an optimization point of view, production of fully formatted test forms directly from the item pool using…

Results of field testing of radioactive waste forms using lysimeters

International Nuclear Information System (INIS)

McConnell, J.W., Jr.; Rogers, R.D.; Jastrow, J.D.; Wickliff, D.S.

1992-01-01

The Field Lysimeter Investigation: Low-Level Waste Data Base Development Program is obtaining informaiton on the performance of radioactive waste in a disposal environment. Waste forms fabricated using ion-exchange resins from EPICOR-II prefilters employed in the cleanup of the Three Mile Island (TMI) Nuclear Power Station are being tested to develop a low-level waste data base and to obtain information on survivability of waste forms in a disposal environment. In this paper, radionuclide releases from waste forms in the first six years of sampling are presented and discussed. Application of lysimeter data to use in performance assessment models is presented. Initial results from use of data in a performance assessment model are discussed

The use of a flow test and a flow model in evaluating the durability of various nuclear waste-form materials

International Nuclear Information System (INIS)

Barkatt, A.; Barkatt, A.; Boroomand, M.A.

1983-01-01

The comprehensive predictive model described in this paper has been briefly outlined for a single particular set of repository parameters in an earlier paper. A general detailed derivation and a detailed illustration of the use of this method in comparative evaluation of a variety of waste-form materials are given. The model focuses on the long-term leach rate of materials under all possible water flow rates through a repository site, given any exposure configuration (i.e., ratio between the exposed area of the waste form and the volume of water with which it is in effective contact) which is considered most representative of the actual repository conditions. The model permits direct calculation of the annual fractional release rate of the major matrix elements as well as of any other components of a waste form. This makes it possible to evaluate how well various waste forms meet long-term durability criteria such as those proposed by the U.S. Nuclear Regulatory Commission, makes it possible to obtain such release rates, corresponding to the entire range of flow conditions expected in a repository down to very slow flow rates by conducting dynamic laboratory tests at practical rates of leachant exchange at relatively high surfaceto-volume ratios, following the leachate composition until the leach rates approach constant values, and normalizing the data to the surface-to-volume ratio expected under repository conditions. The purpose of this paper is to outline the general derivation of the model and to describe the results of applying the model in dynamic leach tests carried out on five different waste-form materials over the entire range of effective flow rates expected under repository conditions

Peculiarities of radionuclide contamination of different Semipalatinsk nuclear test site (SNTS) zones

International Nuclear Information System (INIS)

Kadyrzhanov, K.K.; Khazhekber, S.; Lukashenko, S.N.; Solodukhin, V.P.; Kazachevskij, I.V.; Poznyak, V.L.; Knyazev, B.B.; Rofer, Ch.

2002-01-01

The Semipalatinsk Nuclear Test Site occupies about 18500 km 2 . There are 3 basic test zones in this territory including various test platforms where different character nuclear explosions were carried out. On the test platforms of the 'Opytnoe Pole' zone air and ground tests were performed, including nuclear and hydronuclear (without nuclear reaction) explosions. On the other zones (the Degelen mountains and Balapan valley) the underground tests including camouflaged and excavation nuclear explosions were carried out. Each kind of these tests can be characterised by the quantity and composition of radionuclides which were formed during the nuclear explosion, by the area of their distribution, localisation of the radionuclides at various sites, radionuclide species in soil. Transfer of the products of the air and the ground nuclear explosions by air flows and their sedimentation on the ground surfaces have caused broadband radioactive plumes extending over hundreds of kilometres. As a result of hydronuclear experiments, plenty of alpha-active radionuclides, consisting of a nuclear device is thrown locally out. Besides the ground and the air explosions, radiation conditions of the territory of the SNTS were influenced by excavation explosions with ground throwing out. Such tests resulted in an intensive local pollution. Other zone of an original pollution is the Degelen mountains. Although an basic mass of the nuclear explosion products is obviously concentrated in basin cavities of the tunnels, the radionuclides are taken out on a day time surface together with waters acting in the basin cavity of the tunnels. The results of investigation of radionuclide pollution on the various platforms of the SNTS territory are presented. The results characterise the radionuclide pollution by specificity of spent tests

Separating form factor and nuclear model effects in quasielastic neutrino-nucleus scattering

Science.gov (United States)

Wieske, Joseph

2017-09-01

When studying neutrino oscillations an understanding of charged current quasielastic (CCQE) neutrino-nucleus scattering is imperative. This interaction depends on a nuclear model as well as knowledge of form factors. In the past, CCQE data from the MiniBooNE experiment was analyzed assuming the Relativistic Fermi Gas (RFG) nuclear model, an axial dipole form factor in, and using the the z-expansion for the axial form factor in. We present the first analysis that combines a non-RFG nuclear model, in particular the Correlated Fermi Gas nuclear model (CFG) of, and the z expansion for the axial form factor. This will allow us to separate form factor and nuclear model effects in CCQE scattering. This project was supported through the Wayne State University REU program under NSF Grant PHY-1460853 and by the DOE Grant DE-SC0007983.

Generic test procedure for the qualification of a nuclear emergency generator

International Nuclear Information System (INIS)

Simonis, J.C.; Bowman, S.W.

1985-01-01

This paper describes the proposed analytical and experimental procedures for the qualification of the standby generators and exciters used in the Emergency Diesel Generator Systems in a nuclear power plant. The components which require qualification are identified through a failure mode analysis of the systems conducted using engineering drawings updated to include all field changes. The qualification of each component includes the margins given in IEEE Std. 323-1974, ''Qualifying Class 1E Equipment for Nuclear Power Generating Stations.'' These margins are combined with the plant specific data to define an enveloping set of environmental parameters. This set of enveloping parameters, plus margin, form the bases for the analysis or test qualification tasks. Proposed qualification of the composite electrical insulation systems used in the generator and exciter on the form or random wound coils is by traceable testing. However, before testing the thermal and radiation degradation data used in the design of the generator and exciter are evaluated to identify if these data are sufficiently traceable to eliminate the need for additional insulation tests. The required tests are guided by applicable standards

Nuclear test ban's last chance

International Nuclear Information System (INIS)

Barnaby, F.

1976-01-01

It is argued that if nuclear disarmament is the aim then some arms control treaties have been counterproductive. The two great powers have conducted, albeit underground, more nuclear explosions in the 12 years since the partial test ban than they did in the preceding 18 years, 1945 to 1963. The partial test ban treaty obliges the parties to negotiate a ban on 'all test explosions of nuclear weapons for all time'. After 12 years of negotiations very little progress has been made to this end. The USA and the USSR signed a bilateral Threshold Test Ban Treaty in 1974 banning 'any underground nuclear weapon tests having a yield exceeding 150 kilo-tons... beginning 31 March, 1976', a protocol describes how compliance is to be verified, and Article III requires that an agreement is to be negotiated governing peaceful nuclear explosions. From the point of view of disarmament it would be much better if the threshold test ban treaty were not ratified and a comprehensive test ban treaty were negotiated instead. The main official reason given for the failure to negotiate such a treaty is the problem of verification. However it is argued that due to recent progress in seismology there are no longer significant technical obstacles to the negotiation of a comprehensive test ban treaty. But there is lack of political will to obtain such a treaty. (U.K.)

Towards a nuclear-test ban

International Nuclear Information System (INIS)

1991-01-01

In 1986 and again in 1987 the General Assembly adopted resolutions by which it called on States conducting nuclear-test explosions to notify the Secretary-General, within one week of each explosion, of the time, place, yield and site characteristics of the test and also invited all other States to provide any such data on nuclear explosions that they might have. Over the years, in the Conference on Disarmament, members of the Group of 21 (mostly neutral and non-aligned countries) have continued to attach the utmost importance to the urgent conclusion of a comprehensive test-ban treaty as a significant contribution to the aim of ending the qualitative refinement of nuclear weapons and the development of new types of such weapons as well as of reversing the nuclear-arms race and achieving nuclear disarmament. In 1995 a conference will be convened to decide whether the non-proliferation Treaty will continue in force indefinitely, or will be extended for an additional fixed period or periods. Many States support the view that a comprehensive test ban would be a significant contribution to the non-proliferation of nuclear weapons; and some believe that, without a cessation of nuclear testing, it may not be possible to extend the NPT well beyond 1995. Other States, however, are of the opinion that the NPT, independently, offers benefits for the security of all States and, by its extension, will continue to do so

Test-qualification experience with non-destructive material analysis system performed at Paks Nuclear Power Plant and its usage in non-nuclear fields

International Nuclear Information System (INIS)

Somogyi, Gy.; Szabo, D.

2003-01-01

The need for qualification of non-destructive material analysis has been recognised in controlling nuclear energy production process. This test-qualification has been performed as first of its kind after the task has been assigned by the National Nuclear Energy Agency. The input documents for the test were. Technical Specification, Analysis Technology, Technical Justification. Test-qualification has been performed with real form control bodies developed by the Rez Nuclear Research Institute, in which the planned defects has been produced by spark-chipping. The qualification procedure has been summarized in a Qualification Folder and given to the national agency to issue a qualification certificate. The procedure might be interesting mostly for companies delivering nuclear power plant assemblies. Similar needs are formulated in standards relative to the qualification of non-nuclear material testing methods (MSZ EN 17025 and EU). (Gy.M.)

Comprehensive Nuclear Test-ban Treaty

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-07-01

The Comprehensive Nuclear Test-Ban Treaty was adopted by the General Assembly on 10 September 1996 (Res/50/245) and was open for signature by all states on 24 September 1996. It will enter into force 180 days after the date of deposit of the instruments of ratification by all states listed in Annex 2 to the Treaty. This document reproduces the text of the Treaty and the Protocol to the Comprehensive Nuclear Test-Ban Treaty Protocol to the Comprehensive Nuclear Test-Ban Treaty. 4 tabs.

Comprehensive Nuclear Test-ban Treaty

International Nuclear Information System (INIS)

1998-01-01

The Comprehensive Nuclear Test-Ban Treaty was adopted by the General Assembly on 10 September 1996 (Res/50/245) and was open for signature by all states on 24 September 1996. It will enter into force 180 days after the date of deposit of the instruments of ratification by all states listed in Annex 2 to the Treaty. This document reproduces the text of the Treaty and the Protocol to the Comprehensive Nuclear Test-Ban Treaty Protocol to the Comprehensive Nuclear Test-Ban Treaty

Nuclear Test-Experimental Science

International Nuclear Information System (INIS)

Struble, G.L.; Donohue, M.L.; Bucciarelli, G.; Hymer, J.D.; Kirvel, R.D.; Middleton, C.; Prono, J.; Reid, S.; Strack, B.

1988-01-01

Fiscal year 1988 has been a significant, rewarding, and exciting period for Lawrence Livermore National Laboratory's nuclear testing program. It was significant in that the Laboratory's new director chose to focus strongly on the program's activities and to commit to a revitalized emphasis on testing and the experimental science that underlies it. It was rewarding in that revolutionary new measurement techniques were fielded on recent important and highly complicated underground nuclear tests with truly incredible results. And it was exciting in that the sophisticated and fundamental problems of weapons science that are now being addressed experimentally are yielding new challenges and understanding in ways that stimulate and reward the brightest and best of scientists. During FY88 the program was reorganized to emphasize our commitment to experimental science. The name of the program was changed to reflect this commitment, becoming the Nuclear Test-Experimental Science (NTES) Program

The nuclear dissuasion without tests

International Nuclear Information System (INIS)

2003-02-01

Since the signature of the french treaty against the nuclear tests (Tice) in 1995, the french engineers must used the simulation to warrant the performance and the safety of weapons. This paper recalls the historical aspects of the french nuclear tests and presents the technological and scientific resources to simulate a nuclear weapon operating. a special interest is given to the computer TERA. (A.L.B.)

Nuclear tests and health: conference proceedings

International Nuclear Information System (INIS)

Beaudeau, M.C.

2002-01-01

This conference was organized by the observatory of French nuclear weapons - CDRPC-, the 'Moruroa e Tatou' association and the association of nuclear test veterans. Its aim was to call upon the victims of nuclear tests to speak about their health problems and to the possible consequences on their children's health. It pleads in favour of a particular legislation and in favour of the creation of an organization which would take for responsibility the health and environmental impacts of nuclear tests. (J.S.)

Alternative solidified forms for nuclear wastes

International Nuclear Information System (INIS)

McElroy, J.L.; Ross, W.A.

1976-01-01

Radioactive wastes will occur in various parts of the nuclear fuel cycle. These wastes have been classified in this paper as high-level waste, intermediate and low-level waste, cladding hulls, and residues. Solidification methods for each type of waste are discussed in a multiple barrier context of primary waste form, applicable coatings or films, matrix encapsulation, canister, engineered structures, and geological storage. The four major primary forms which have been most highly developed are glass for HLW, cement for ILW, organics for LLW, and metals for hulls

Studies of Health Effects from Nuclear Testing near the Semipalatinsk Nuclear Test Site, Kazakhstan

Directory of Open Access Journals (Sweden)

Bernd Grosche

2015-05-01

Full Text Available The nuclear bomb testing conducted at the Semipalatinsk nuclear test site in Kazakhstan is of great importance for today’s radiation protection research, particularly in the area of low dose exposures. This type of radiation is of particular interest due to the lack of research in this field and how it impacts population health. In order to understand the possible health effects of nuclear bomb testing, it is important to determine what studies have been conducted on the effects of low dose exposure and dosimetry, and evaluate new epidemiologic data and biological material collected from populations living in proximity to the test site. With time, new epidemiological data has been made available, and it is possible that these data may be linked to biological samples. Next to linking existing and newly available data to examine health effects, the existing dosimetry system needs to be expanded and further developed to include residential areas, which have not yet been taken into account. The aim of this paper is to provide an overview of previous studies evaluating the health effects of nuclear testing, including some information on dosimetry efforts, and pointing out directions for future epidemiologic studies.

Studies of Health Effects from Nuclear Testing near the Semipalatinsk Nuclear Test Site, Kazakhstan.

Science.gov (United States)

Grosche, Bernd; Zhunussova, Tamara; Apsalikov, Kazbek; Kesminiene, Ausrele

2015-01-01

The nuclear bomb testing conducted at the Semipalatinsk nuclear test site in Kazakhstan is of great importance for today's radiation protection research, particularly in the area of low dose exposures. This type of radiation is of particular interest due to the lack of research in this field and how it impacts population health. In order to understand the possible health effects of nuclear bomb testing, it is important to determine what studies have been conducted on the effects of low dose exposure and dosimetry, and evaluate new epidemiologic data and biological material collected from populations living in proximity to the test site. With time, new epidemiological data has been made available, and it is possible that these data may be linked to biological samples. Next to linking existing and newly available data to examine health effects, the existing dosimetry system needs to be expanded and further developed to include residential areas, which have not yet been taken into account. The aim of this paper is to provide an overview of previous studies evaluating the health effects of nuclear testing, including some information on dosimetry efforts, and pointing out directions for future epidemiologic studies.

Nuclear-waste-package materials degradation modes and accelerated testing

International Nuclear Information System (INIS)

1981-09-01

This report reviews the materials degradation modes that may affect the long-term behavior of waste packages for the containment of nuclear waste. It recommends an approach to accelerated testing that can lead to the qualification of waste package materials in specific repository environments in times that are short relative to the time period over which the waste package is expected to provide containment. This report is not a testing plan but rather discusses the direction for research that might be considered in developing plans for accelerated testing of waste package materials and waste forms

Ground test facility for nuclear testing of space reactor subsystems

International Nuclear Information System (INIS)

Quapp, W.J.; Watts, K.D.

1985-01-01

Two major reactor facilities at the INEL have been identified as easily adaptable for supporting the nuclear testing of the SP-100 reactor subsystem. They are the Engineering Test Reactor (ETR) and the Loss of Fluid Test Reactor (LOFT). In addition, there are machine shops, analytical laboratories, hot cells, and the supporting services (fire protection, safety, security, medical, waste management, etc.) necessary to conducting a nuclear test program. This paper presents the conceptual approach for modifying these reactor facilities for the ground engineering test facility for the SP-100 nuclear subsystem. 4 figs

Field vibration test of principal equipment of nuclear power plants

Energy Technology Data Exchange (ETDEWEB)

Shiraki, Kazuhiro; Fujita, Katsuhisa; Kajimura, Motohiko; Ikegami, Yasuhiko; Hanzawa, Katsumi; Sakai, Yoshiyuki; Kokubo, Eiji; Igarashi, Shigeru

1984-09-01

Japan is one of the most earthquake-stricken countries in the world, and demands for aseismic design have become severer recently. In a nuclear power plant in particular, consisting of a reactor vessel and other facilities dealing with a radioactive substance in some form or other, it is essential from the standpoint of safety to eliminate any possibility of radioactive hazards for the local public, and the employees at the plant as well, if these facilities are struck by an earthquake. This paper is related to the reactor vessel, reactor primary cooling equipment and piping system and important general piping as examples of important facilities of a nuclear power plant, and discusses vibration tests of an actual plant in the field from the standpoint of enhancing the aseismic safety of the Mitsubishi PWR nuclear power plant. Especially concerning vibration test technology, the effects in the evaluation of aseismic safety and its limits are studied to prove how it contributes to the enhancement of the reliability of aseismic design of nuclear power plants.

The NPT and nuclear testing

International Nuclear Information System (INIS)

Howlett, D.; Simpson, J.

1992-01-01

One of the oldest unachieved aims of international nuclear disarmament and arms limitation negotiations is a Comprehensive Test Ban Treaty (CTBT). The history of the international negotiations, their outcomes and the consequences of Test Ban for the nuclear arsenals of the nuclear weapons states is discussed. The linkage between a CTBT and the Non-Proliferation Treaty is examined. Two strategies for moving towards a CTBT are compared; one a direct one, the other an incremental route. Both have several alternatives which are considered. (UK)

Development and testing of matrices for the encapsulation of glass and ceramic nuclear waste forms

International Nuclear Information System (INIS)

Wald, J.W.; Brite, D.W.; Gurwell, W.E.; Buckwalter, C.Q.; Bunnell, L.R.; Gray, W.J.; Blair, H.T.; Rusin, J.M.

1982-02-01

This report details the results of research on the matrix encapsulation of high level wastes at PML over the past few years. The demonstrations and tests described were designed to illustrate how the waste materials are effected when encapsulated in an inert matrix. Candidate materials evaluated for potential use as matrices for encapslation of pelletized ceramics or glass marbles were categorized into four groups: metals, glasses, ceramics, and graphite. Two processing techniques, casting and hot pressing, were investigated as the most promising methods of formation or densification of the matrices. The major results reported deal with the development aspects. However, chemical durability tests (leach tests) of the matrix materials themselves and matrix-waste form composites are also reported. Matrix waste forms can provide a low porosity, waste-free barrier resulting in increased leach protection, higher impact strength and improved thermal conductivity compared to unencapsulated glass or ceramic waste materials. Glass marbles encapsulated in a lead matrix offer the most significant improvement in waste form stability of all combinations evaluated. This form represents a readily demonstrable process that provides high thermal conductivity, mechanical shock resistance, radiation shielding and increased chemical durability through both a chemical passivation mechanism and as a physical barrier. Other durable matrix waste forms evaluated, applicable primarily to ceramic pellets, involved hot-pressed titanium or TiO 2 materials. In the processing of these forms, near 100% dense matrices were obtained. The matrix materials had excellent compatibility with the waste materials and superior potential chemical durability. Cracking of the hot-pressed ceramic matrix forms, in general, prevented the realization of their optimum properties

Stress test of the nuclear power plants performed in Taiwan

International Nuclear Information System (INIS)

Wu, C.H.; Teng, W.C.; Chang, S.; Chen, Y.B.

2014-01-01

In the wake of Japan's Fukushima Daiichi Nuclear Power Plants event, the Atomic Energy Council (AEC) has asked Taiwan's Nuclear Power Plant operator (TPC) to re-examine and re-evaluate the vulnerabilities of its nuclear units, and furthermore, take possible countermeasures against extreme natural disasters, including earthquake, tsunami and rock-and-mud slide. The evaluation process should be based on both within and beyond Design Basis Accidents, by reference to the actions recommended by the world nuclear authorities and groups, namely, IAEA, USNRC, NEI, ENSREG and WANO. Taiwan is a very densely populated region of the world. Furthermore, like Japan, due to its geophysical position, Taiwan is prone to large scale earthquakes, and although historically rare, Taiwan also faces the potential risk of tsunamis. AEC also asked TPC to perform the stress test following the specification given by WENRA (later ENSREG) and conducted in all the EU's nuclear reactors. After completion of the stress test for all the nuclear power plants, AEC was trying to have the reports peer reviewed by international organizations, as EU did. The OECD/NEA accepted AEC's request and formed a review team specific to the review of Taiwan's National Report for the Stress Test. There were 18 follow-up items after the NEA's review. Based on these items, AEC developed five orders to require TPC further enhancing their capabilities to cope with extreme natural hazards. The ENSREG also formed a nine-expert review team for Taiwan's Stress Test in response to AEC's request almost at the same time as the OECD/NEA. The ENSREG review team began their works in June 2013 by desktop review, and ended in early October 2013 by country visit to Taiwan. While the assessment of post-Fukushima evaluation reveals neither immediate nuclear safety concerns nor threats to the public health and safety, AEC requested that TPC focus on strengthening its re-evaluation on design

Stress test of the nuclear power plants performed in Taiwan

Energy Technology Data Exchange (ETDEWEB)

Wu, C.H.; Teng, W.C.; Chang, S.; Chen, Y.B. [Atomic Energy Council, Taipei, Taiwan (China)

2014-07-01

In the wake of Japan's Fukushima Daiichi Nuclear Power Plants event, the Atomic Energy Council (AEC) has asked Taiwan's Nuclear Power Plant operator (TPC) to re-examine and re-evaluate the vulnerabilities of its nuclear units, and furthermore, take possible countermeasures against extreme natural disasters, including earthquake, tsunami and rock-and-mud slide. The evaluation process should be based on both within and beyond Design Basis Accidents, by reference to the actions recommended by the world nuclear authorities and groups, namely, IAEA, USNRC, NEI, ENSREG and WANO. Taiwan is a very densely populated region of the world. Furthermore, like Japan, due to its geophysical position, Taiwan is prone to large scale earthquakes, and although historically rare, Taiwan also faces the potential risk of tsunamis. AEC also asked TPC to perform the stress test following the specification given by WENRA (later ENSREG) and conducted in all the EU's nuclear reactors. After completion of the stress test for all the nuclear power plants, AEC was trying to have the reports peer reviewed by international organizations, as EU did. The OECD/NEA accepted AEC's request and formed a review team specific to the review of Taiwan's National Report for the Stress Test. There were 18 follow-up items after the NEA's review. Based on these items, AEC developed five orders to require TPC further enhancing their capabilities to cope with extreme natural hazards. The ENSREG also formed a nine-expert review team for Taiwan's Stress Test in response to AEC's request almost at the same time as the OECD/NEA. The ENSREG review team began their works in June 2013 by desktop review, and ended in early October 2013 by country visit to Taiwan. While the assessment of post-Fukushima evaluation reveals neither immediate nuclear safety concerns nor threats to the public health and safety, AEC requested that TPC focus on strengthening its re-evaluation on design

Can the deterrence survive to nuclear tests ban

International Nuclear Information System (INIS)

Gaffney, F.J. Jr.

1996-01-01

The problem of the soundness of the nuclear tests stopping is discussed here. The safety, the durability of nuclear weapons need nuclear tests. So, unless other means able to guarantee the deterrence, it is prejudicial to stop nuclear tests and to sign a non proliferation treaty with the option of zero nuclear explosion. (N.C.)

Calculated concentrations of any radionuclide deposited on the ground by release from underground nuclear detonations, tests of nuclear rockets, and tests of nuclear ramjet engines

International Nuclear Information System (INIS)

Hicks, H.G.

1981-11-01

This report presents calculated gamma radiation exposure rates and ground deposition of related radionuclides resulting from three types of event that deposited detectable radioactivity outside the Nevada Test Site complex, namely, underground nuclear detonations, tests of nuclear rocket engines and tests of nuclear ramjet engines

Forming Tests for Laser Welded Blanks

DEFF Research Database (Denmark)

Bagger, Claus; Olsen, Flemming Ove; Rasmussen, Mads

1998-01-01

Ratio test (LDR)Tensile testBulge testMarziniak testPractical examples obtained for laser welded blanks are shown. In combination, tensile tests and the Bulge test can form the so-called Forming Limiting Curves and examples of curves obtained from laser welded blanks are shown.......In this paper different means for testing the formability of new material combinations used as tailored blanks in the automotive industry are presented. The following forming techniques will be described and their benefits and drawbacks presented :Limiting Dome Height test (LDH)Limiting Drawing...

Importance of tests in nuclear facilities

International Nuclear Information System (INIS)

Guillemard, B.

1985-10-01

In nuclear facilities, safety related systems and equipments are subject, along their whole service-life, to numerous tests. This paper analyses the role of tests in the successive stages of design, construction, exploitation of a nuclear facility. It examines several aspects of test quality control: definition of needs, test planning, intrinsic quality of each test, control of interfaces (test are both the end and the starting point of many actions concerned by quality) and the application [fr

The Indian nuclear test in a global perspective

International Nuclear Information System (INIS)

Subrahmanyam, K.

1974-01-01

A peaceful nuclear explosion test was carried out by India on 18 May, 1974 at Pokharan in the Rajasthan Desert. The test was carried out as a part of India's steady programme to develop nuclear energy for peaceful purposes and there was no diversion of resources from development as is charged by some nations. The test has broken the monopoly of the nuclear superpowers to conduct nuclear tests for which they are entiltled by the Non-proliferation Treaty (NPT) and at the same time, sharply focussed the attention on the discriminatory character of the NPT which does not allow non-nuclear states to carry out nuclear tests even for peaceful purposes. It is argued that India's going nuclear may prove, in the long run, beneficial to the cause of disarmament. (M.G.B.)

Advanced waste forms from spent nuclear fuel

International Nuclear Information System (INIS)

Ackerman, J.P.; McPheeters, C.C.

1995-01-01

More than one hundred spent nuclear fuel types, having an aggregate mass of more than 5000 metric tons (2700 metric tons of heavy metal), are stored by the United States Department of Energy. This paper proposes a method for converting this wide variety of fuel types into two waste forms for geologic disposal. The method is based on a molten salt electrorefining technique that was developed for conditioning the sodium-bonded, metallic fuel from the Experimental Breeder Reactor-II (EBR-II) for geologic disposal. The electrorefining method produces two stable, optionally actinide-free, high-level waste forms: an alloy formed from stainless steel, zirconium, and noble metal fission products, and a ceramic waste form containing the reactive metal fission products. Electrorefining and its accompanying head-end process are briefly described, and methods for isolating fission products and fabricating waste forms are discussed

SAFE testing nuclear rockets economically

International Nuclear Information System (INIS)

Howe, Steven D.; Travis, Bryan; Zerkle, David K.

2003-01-01

Several studies over the past few decades have recognized the need for advanced propulsion to explore the solar system. As early as the 1960s, Werner Von Braun and others recognized the need for a nuclear rocket for sending humans to Mars. The great distances, the intense radiation levels, and the physiological response to zero-gravity all supported the concept of using a nuclear rocket to decrease mission time. These same needs have been recognized in later studies, especially in the Space Exploration Initiative in 1989. One of the key questions that has arisen in later studies, however, is the ability to test a nuclear rocket engine in the current societal environment. Unlike the Rover/NERVA programs in the 1960s, the rocket exhaust can no longer be vented to the open atmosphere. As a consequence, previous studies have examined the feasibility of building a large-scale version of the Nuclear Furnace Scrubber that was demonstrated in 1971. We have investigated an alternative that would deposit the rocket exhaust along with any entrained fission products directly into the ground. The Subsurface Active Filtering of Exhaust, or SAFE, concept would allow variable sized engines to be tested for long times at a modest expense. A system overview, results of preliminary calculations, and cost estimates of proof of concept demonstrations are presented. The results indicate that a nuclear rocket could be tested at the Nevada Test Site for under $20 M

Melt-Dilute Spent Nuclear Fuel Form Criticality Summary Report; FINAL

International Nuclear Information System (INIS)

Vinson, D.W.

2002-01-01

Criticality analysis of the proposed Melt-Dilute (MD) form of aluminum-based spent nuclear fuel (SNF), under geologic repository conditions, was performed following the methodology, documented in the Disposal Criticality Analysis Methodology Topical Report. This methodology evaluates the potential for nuclear criticality as determined by the composition of the waste and its geometry, namely waste form configuration, including presence of moderator, reflecting structural material, and neutron absorbers. The initial emplaced configuration of the SNF form is a dry package placed in a mined repository passageway. Criticality calculations show that even with waste package failure, followed by degradation of material within the waste package and potential loss of neutron absorber materials, sub-critical conditions can be maintained

Radiation consequences of the nuclear tests on the Semipalatinsk test site

International Nuclear Information System (INIS)

Logachev, V.A.; Logacheva, L.A.

2001-01-01

In the paper the results of retrospective evaluation for radiation situation and radiation doses of population in the zones of the Semipalatinsk test site activity influence are presented. For the measurements the data obtained during analysis, study and summarizing of the archival materials including information on nuclear tests on this site and results of radiation surveys, those were carried out after each test were used. The information testifying most substantial environment contamination taking place after four surface explosions (29.08.1949, 24.09.1951, 12.08.1953, 24.08.1956) is presented as well. After these dose-forming explosions the irradiation doses of the population inhabiting out the regime zone have been exceeded the maximum permissible levels. Results of analysis of archival materials were used for assessment of doses of internal and external irradiation of residents of inhabited points situated on the both the territory of the Republic of Kazakhstan - mainly close to the test site - and the territories of a number of regions of the Russian Federation are locating on the little distance from the tests site

Compressive strength test for cemented waste forms: validation process

International Nuclear Information System (INIS)

Haucz, Maria Judite A.; Candido, Francisco Donizete; Seles, Sandro Rogerio

2007-01-01

In the Cementation Laboratory (LABCIM), of the Development Centre of the Nuclear Technology (CNEN/CDTN-MG), hazardous/radioactive wastes are incorporated in cement, to transform them into monolithic products, preventing or minimizing the contaminant release to the environment. The compressive strength test is important to evaluate the cemented product quality, in which it is determined the compression load necessary to rupture the cemented waste form. In LABCIM a specific procedure was developed to determine the compressive strength of cement waste forms based on the Brazilian Standard NBR 7215. The accreditation of this procedure is essential to assure reproductive and accurate results in the evaluation of these products. To achieve this goal the Laboratory personal implemented technical and administrative improvements in accordance with the NBR ISO/IEC 17025 standard 'General requirements for the competence of testing and calibration laboratories'. As the developed procedure was not a standard one the norm ISO/IEC 17025 requests its validation. There are some methodologies to do that. In this paper it is described the current status of the accreditation project, especially the validation process of the referred procedure and its results. (author)

Results after nine years of field testing low-level radioactive waste forms using lysimeters

International Nuclear Information System (INIS)

McConnell, J.W. Jr.; Rogers, R.D.; Jastrow, J.D.; Sanford, W.E.; Sullivan, T.M.

1995-01-01

The Field Lysimeter Investigations: Low-Level Waste Data Base Development Program is obtaining information on the performance of radioactive waste forms. Ion-exchange resins from a nuclear power station were solidified into waste forms using Portland cement and vinyl ester-styrene. These waste forms are being tested to develop a low-level waste data base and to obtain information on survivability of waste forms in a disposal environment. This paper reviews radionuclide releases from those waste forms in the first 9 years of sampling. Included is a discussion of the recently discovered upward migration of radionuclides. Also, lysimeter data are applied to a performance assessment source term model, and initial results are presented

A history of US nuclear testing and its influence on nuclear thought, 1945-1963

CERN Document Server

Blades, David M

2014-01-01

As states continue to pursue nuclear weaponry, nuclear testing remains an important political issue in the twenty-first century. This survey examines how and why the U.S. conducted nuclear tests from 1945 through 1963 and the resulting influence on key questions from normalization and de-normalization up to the Nuclear Test Ban Treaty of 1963.

Nuclear test ban verification

International Nuclear Information System (INIS)

Chun, Kin-Yip

1991-07-01

This report describes verification and its rationale, the basic tasks of seismic verification, the physical basis for earthquake/explosion source discrimination and explosion yield determination, the technical problems pertaining to seismic monitoring of underground nuclear tests, the basic problem-solving strategy deployed by the forensic seismology resarch team at the University of Toronto, and the scientific significance of the team's research. The research carried out at the Univeristy of Toronto has two components: teleseismic verification using P wave recordings from the Yellowknife Seismic Array (YKA), and regional (close-in) verification using high-frequency L g and P n recordings from the Eastern Canada Telemetered Network. Major differences have been found in P was attenuation among the propagation paths connecting the YKA listening post with seven active nuclear explosion testing areas in the world. Significant revisions have been made to previously published P wave attenuation results, leading to more interpretable nuclear explosion source functions. (11 refs., 12 figs.)

Australia - a nuclear weapons testing ground

International Nuclear Information System (INIS)

Dobbs, Michael.

1993-01-01

Between 1952 and 1958 Britain conducted five separate nuclear weapons trials in Australia. Australia had the uninhabited wide open spaces and the facilities which such tests need and Britain was able to use its special relationship with Australia to get agreement to conduct atomic tests in Australia and establish a permanent test site at Maralinga. Other non-nuclear tests were conducted between 1953-1963. The story of Britain's involvement in atomic weapons testing in Australia is told through its postal history. Both official and private covers are used to show how the postal communications were established and maintained throughout the test years. (UK)

Business of Nuclear Safety Analysis Office, Nuclear Technology Test Center

International Nuclear Information System (INIS)

Hayakawa, Masahiko

1981-01-01

The Nuclear Technology Test Center established the Nuclear Safety Analysis Office to execute newly the works concerning nuclear safety analysis in addition to the works related to the proving tests of nuclear machinery and equipments. The regulations for the Nuclear Safety Analysis Office concerning its organization, business and others were specially decided, and it started the business formally in August, 1980. It is a most important subject to secure the safety of nuclear facilities in nuclear fuel cycle as the premise of developing atomic energy. In Japan, the strict regulation of safety is executed by the government at each stage of the installation, construction, operation and maintenance of nuclear facilities, based on the responsibility for the security of installers themselves. The Nuclear Safety Analysis Office was established as the special organ to help the safety examination related to the installation of nuclear power stations and others by the government. It improves and puts in order the safety analysis codes required for the cross checking in the safety examination, and carries out safety analysis calculation. It is operated by the cooperation of the Science and Technology Agency and the Agency of Natural Resources and Energy. The purpose of establishment, the operation and the business of the Nuclear Safety Analysis Office, the plan of improving and putting in order of analysis codes, and the state of the similar organs in foreign countries are described. (Kako, I.)

Computational Efficient Upscaling Methodology for Predicting Thermal Conductivity of Nuclear Waste forms

International Nuclear Information System (INIS)

Li, Dongsheng; Sun, Xin; Khaleel, Mohammad A.

2011-01-01

This study evaluated different upscaling methods to predict thermal conductivity in loaded nuclear waste form, a heterogeneous material system. The efficiency and accuracy of these methods were compared. Thermal conductivity in loaded nuclear waste form is an important property specific to scientific researchers, in waste form Integrated performance and safety code (IPSC). The effective thermal conductivity obtained from microstructure information and local thermal conductivity of different components is critical in predicting the life and performance of waste form during storage. How the heat generated during storage is directly related to thermal conductivity, which in turn determining the mechanical deformation behavior, corrosion resistance and aging performance. Several methods, including the Taylor model, Sachs model, self-consistent model, and statistical upscaling models were developed and implemented. Due to the absence of experimental data, prediction results from finite element method (FEM) were used as reference to determine the accuracy of different upscaling models. Micrographs from different loading of nuclear waste were used in the prediction of thermal conductivity. Prediction results demonstrated that in term of efficiency, boundary models (Taylor and Sachs model) are better than self consistent model, statistical upscaling method and FEM. Balancing the computation resource and accuracy, statistical upscaling is a computational efficient method in predicting effective thermal conductivity for nuclear waste form.

Database on radioecological situation in Semipalatinsk nuclear test site

International Nuclear Information System (INIS)

Turkebaev, T.Eh.; Kislitsin, S.B.; Lopuga, A.D.; Kuketaev, A.T.; Kikkarin, S.M.

1999-01-01

One of the main objectives of the National Nuclear Center of the Republic of Kazakstan is to define radioecological situation in details, conduct a continuous monitoring and eliminate consequences of nuclear explosions at Semipalatinsk nuclear test site. Investigations of Semipalatinsk nuclear test site area contamination by radioactive substances and vindication activity are the reasons for development of computer database on radioecological situation of the test site area, which will allow arranging and processing the available and entering information about the radioecological situation, assessing the effect of different testing factors on the environment and health of the Semipalatinsk nuclear test site area population.The described conception of database on radioecological situation of the Semipalatinsk nuclear test site area cannot be considered as the final one. As new information arrives, structure and content of the database is updated and optimized. New capabilities and structural elements may be provided if new aspects in Semipalatinsk nuclear test site area contamination study (air environment study, radionuclides migration) arise

Nuclear system test simulator

International Nuclear Information System (INIS)

Sawyer, S.D.; Hill, W.D.; Wilson, P.A.; Steiner, W.M.

1987-01-01

A transportable test simulator is described for a nuclear power plant. The nuclear power plant includes a control panel, a reactor having actuated rods for moving into and out of a reactor for causing the plant to operate, and a control rod network extending between the control panel and the reactor rods. The network serially transmits command words between the panel and rods, and has connecting interfaces at preselected points remote from the control panel between the control panel and rods. The test simulator comprises: a test simulator input for transport to and connection into the network at at least one interface for receiving the serial command words from the network. Each serial command includes an identifier portion and a command portion; means for processing interior of the simulator for the serial command words for identifying that portion of the power plant designated in the identifier portion and processing the word responsive to the command portion of the word after the identification; means for generating a response word responsive to the command portion; and output means for sending and transmitting the response word to the nuclear power plant at the interface whereby the control panel responds to the response word

Verifying seismic design of nuclear reactors by testing. Volume 1: test plan

Energy Technology Data Exchange (ETDEWEB)

1979-07-20

This document sets forth recommendations for a verification program to test the ability of operational nuclear power plants to achieve safe shutdown immediately following a safe-shutdown earthquake. The purpose of the study is to develop a program plan to provide assurance by physical demonstration that nuclear power plants are earthquake resistant and to allow nuclear power plant operators to (1) decide whether tests should be conducted on their facilities, (2) specify the tests that should be performed, and (3) estimate the cost of the effort to complete the recommended test program.

Verifying seismic design of nuclear reactors by testing. Volume 1: test plan

International Nuclear Information System (INIS)

1979-01-01

This document sets forth recommendations for a verification program to test the ability of operational nuclear power plants to achieve safe shutdown immediately following a safe-shutdown earthquake. The purpose of the study is to develop a program plan to provide assurance by physical demonstration that nuclear power plants are earthquake resistant and to allow nuclear power plant operators to (1) decide whether tests should be conducted on their facilities, (2) specify the tests that should be performed, and (3) estimate the cost of the effort to complete the recommended test program

Verification methods for treaties limiting and banning nuclear tests

International Nuclear Information System (INIS)

Voloshin, N.P.

1998-01-01

Treaty on limitation of underground nuclear weapon tests and treaty on world banning of nuclear tests contribute to and accompany the process of nuclear disarmament. Test ban in three (Moscow treaty of 1963) as well as the Threshold Test Ban up to 1991 was controlled only with national means. But since 1991 nuclear test threshold of 150 kt has been measured with hydrodynamic and tele seismic methods and checked by the inspection. Distinctive feature of this control is that control is that it is bilateral. This conforms to Treaty on limitation of underground nuclear weapon tests signed by two countries - USA and USSR. The inspection at the place of tests requires monitoring of the test site of the party conducting a test and geological information of rock in the area of explosion. In the treaty of the World Nuclear Test Ban the following ways of international control are provided for: - seismologic measurements; - radionuclide measurements; - hydro-acoustics measurements; - infra-sound measurements; - inspection at the place of the tests conduction

Cerium, uranium, and plutonium behavior in glass-bonded sodalite, a ceramic nuclear waste form

International Nuclear Information System (INIS)

Lewis, M. A.; Lexa, D.; Morss, L. R.; Richmann, M. K.

1999-01-01

Glass-bonded sodalite is being developed as a ceramic waste form (CWF) to immobilize radioactive fission products, actinides, and salt residues from electrometallurgical treatment of spent nuclear reactor fuel. The CWF consists of about 75 mass % sodalite, 25 mass % glass, and small amounts of other phases. This paper presents some results and interpretation of physical measurements to characterize the CWF structure, and dissolution tests to measure the release of matrix components and radionuclides from the waste form. Tests have been carried out with specimens of the CWF that contain rare earths at concentrations similar to those expected in the waste form. Parallel tests have been carried out on specimens that have uranium or plutonium as well as the rare earths at concentrations similar to those expected in the waste forms; in these specimens UCl 3 forms UO 2 and PuCl 3 forms PuO 2 . The normalized releases of rare earths in dissolution tests were found to be much lower than those of matrix elements (B, Si, Al, Na). When there is no uranium in the CWF, the release of cerium is two to ten times lower than the release of the other rare earths. The low release of cerium may be due to its tetravalent state in uranium-free CWF. However, when there is uranium in the CWF, the release of cerium is similar to that of the other rare earths. This trivalent behavior of cerium is attributed to charge transfer or covalent interactions among cerium, uranium, and oxygen in (U,Ce)O 2

Nuclear reactor structural material forming less radioactive corrosion product

International Nuclear Information System (INIS)

Nakazawa, Hiroshi.

1988-01-01

Purpose: To provide nuclear reactor structural materials forming less radioactive corrosion products. Constitution: Ni-based alloys such as inconel alloy 718, 600 or inconel alloy 750 and 690 having excellent corrosion resistance and mechanical property even in coolants at high temperature and high pressure have generally been used as nuclear reactor structural materials. However, even such materials yield corrosion products being attacked by coolants circulating in the nuclear reactor, which produce by neutron irradiation radioactive corrosion products, that are deposited in primary circuit pipeways to constitute exposure sources. The present invention dissolves dissolves this problems by providing less activating nuclear reactor structural materials. That is, taking notice on the fact that Ni-58 contained generally by 68 % in Ni changes into Co-58 under irradiation of neutron thereby causing activation, the surface of nuclear reactor structural materials is applied with Ni plating by using Ni with a reduced content of Ni-58 isotopes. Accordingly, increase in the radiation level of the nuclear reactor structural materials can be inhibited. (K.M.)

Why nuclear power failed the market test in the UK

International Nuclear Information System (INIS)

Chesshire, J.

1992-01-01

The Conservative Party's manifesto for the general election of May 1987 contained two pledges of relevance to the UK electricity supply industry (ESI). These were to privatize the industry; and to continue to support the development of civil nuclear power in the private sector. As anticipated by some independent commentators, in the event these objectives proved incompatible. The costs of nuclear power have long been a vexed issue and UK nuclear costs have been higher than those in many other countries. While most of the UK ESI has now been privatized, nuclear generation remains in the public sector. This article seeks to explore the reasons for this fundamental and politically embarrassing policy reversal, a rarity under three successive Conservative administrations since 1979. It would be incorrect to argue that private ownership and nuclear power are inherently incompatible. Rather the specific - competitive - form of privatization proposed for the UK failed to provide sufficient guarantees for the London capital market. Thus, at least in this specific case, nuclear power failed the market test. The implications of this for the UK nuclear industry have been profound. As a result, the UK case has wider international lessons as the pressures for privatization, liberalization and greater cost transparency bear down upon electric utilities in other countries. (author)

State-of-the-art review of materials properties of nuclear waste forms

International Nuclear Information System (INIS)

Mendel, J.E.; Nelson, R.D.; Turcotte, R.P.; Gray, W.J.; Merz, M.D.; Roberts, F.P.; Weber, W.J.; Westsik, J.H. Jr.; Clark, D.E.

1981-04-01

The Materials Characterization Center (MCC) was established at the Pacific Northwest Laboratory to assemble a standardized nuclear waste materials data base for use in research, systems and facility design, safety analyses, and waste management decisions. This centralized data base will be provided through the means of a Nuclear Waste Materials Handbook. The first issue of the Handbook will be published in the fall of 1981 in looseleaf format so that it can be updated as additional information becomes available. To ensure utmost reliability, all materials data appearing in the Handbook will be obtained by standard procedures defined in the Handbook and approved by an independent Materials Review Board (MRB) comprised of materials experts from Department of Energy laboratories and from universities and industry. In the interim before publication of the Handbook there is need for a report summarizing the existing materials data on nuclear waste forms. This review summarizes materials property data for the nuclear waste forms that are being developed for immobilization of high-level radioactive waste. It is intended to be a good representation of the knowledge concerning the properties of HLW forms as of March 1981. The table of contents lists the following topics: introduction which covers waste-form categories, and important waste-form materials properties; physical properties; mechanical properties; chemical durability; vaporization; radiation effects; and thermal phase stability

Confidence in Nuclear Weapons as Numbers Decrease and Time Since Testing Increases

Science.gov (United States)

Adams, Marvin

2011-04-01

As numbers and types of nuclear weapons are reduced, the U.S. objective is to maintain a safe, secure and effective nuclear deterrent without nuclear-explosive testing. A host of issues combine to make this a challenge. An evolving threat environment may prompt changes to security systems. Aging of weapons has led to ``life extension programs'' that produce weapons that differ in some ways from the originals. Outdated and changing facilities pose difficulties for life-extension, surveillance, and dismantlement efforts. A variety of factors can make it a challenge to recruit, develop, and retain outstanding people with the skills and experience that are needed to form the foundation of a credible deterrent. These and other issues will be discussed in the framework of proposals to reduce and perhaps eliminate nuclear weapons.

Handling and disposal of SP-100 ground test nuclear fuel and equipment

International Nuclear Information System (INIS)

Wilson, C.E.; Potter, J.D.; Hodgson, R.D.

1990-05-01

The post SP-100 reactor testing period will focus on defueling the reactor, packaging the various radioactive waste forms, and shipping this material to the appropriate locations. Remote-handling techniques will be developed to defuel the reactor. Packaging the spent fuel and activated reactor components is a challenge in itself. This paper presents an overview of the strategy, methods, and equipment that will be used during the closeout phase of nuclear testing

Handling and disposal of SP-100 ground test nuclear fuel and equipment

International Nuclear Information System (INIS)

Wilson, C.E.; Potter, J.D.; Hodgson, R.D.

1991-01-01

The post SP-100 reactor testing period will focus on defueling the reactor, packaging the various radiactive waste forms, and shipping this material to the appropriate locations. Remote-handling techniques will be developed to defuel the reactor. Packaging the spent fuel and activated reactor components is a challenge in itself. This paper presents an overview of the strategy, methods, and equipment that will be used during the closeout phase of nuclear testing

Upgrade and development of nuclear data production test facility

Energy Technology Data Exchange (ETDEWEB)

Namkung, Won; Ko, I. S.; Cho, M. H.; Lee, Y. S.; Kang, H. S. [Pohang Univ. of Science and Technology, Pohang (Korea, Republic of); Kim, G. N. [Kyungpook National Univ., Daegu (Korea, Republic of); Koh, S. K. [Univ. of Ulsan, Ulsan (Korea, Republic of); Ro, T. I. [Donga Univ., Busan (Korea, Republic of); Choi, G. U. [Korea Research Institute of Standards and Science, Daejeon (Korea, Republic of)

2005-04-15

It is necessary to improve the Pohang Neutron Facility (PNF) in order to be used as a nuclear data production facility for users in both domestic and abroad. We improved following items: upgrade the electron linac, collimators inside the TOF beam pipe, the development and installation of an automatic sample changer, the extension of the TOF beam line, and the data acquisition system. We would like to establish a utilization system for users to measure the nuclear data at the PNF. To do this, we made manuals for the accelerator operation and the data acquisition system. We also made an application form to apply for users to measure the nuclear data in both domestic and abroad. The main object of the Pohang Neutron Facility is to measure the nuclear data in the neutron energy region from thermal neutron to few hundreds of eV. In addition to neutron beams produced at the PNF, photon and electron beams are produced in this facility. We thus utilize this facility for other fields, such as test facility for detectors, activation experiments, polarized neutron beam source, and so on. In addition to these, we could use this facility for training students.

Characterization of glass and glass ceramic nuclear waste forms

International Nuclear Information System (INIS)

Lutze, W.; Borchardt, J.; De, A.K.

1979-01-01

Characteristics of solidified nuclear waste forms, glass and glass ceramic compositions and the properties (composition, thermal stability, crystallization, phase behavior, chemical stability, mechanical stability, and radiation effects) of glasses and glass ceramics are discussed. The preparation of glass ceramics may be an optional step for proposed vitrification plants if tailored glasses are used. Glass ceramics exhibit some improved properties with respect to glasses. The overall leach resistance is similar to that of glasses. An increased leach resistance may become effective for single radionuclides being hosted in highly insoluble crystal phases mainly when higher melting temperatures are applicable in order to get more leach resistant residual glass phases. The development of glass ceramic is going on. The technological feasibility is still to be demonstrated. The potential gain of stability when using glass ceramics qualifies the material as an alternative nuclear waste form

Soviet nuclear testing: The Republics say no

International Nuclear Information System (INIS)

Carter, L.J.

1990-01-01

Massive protests are taking place in Russia against nuclear weapons testing. Efforts have been mounted to stop all testing at Kazakhstan test site near the town of Semipalatinsk, site of the first nuclear detonation in 1949 and of more than 500 test conducted since. Boris Yeltsin proposed just after his election as president of the federation the elimination of testing grounds for nuclear and biological weapons on Russian territory. The central government in Moscow has announced that it is considering closing the Semipalatinsk site. Reaction has also been strong to testing at the Arctic island of Novaya Zemlya, and severe constraints, such as Arctic cold, frozen rocks, high winds, difficult access, and protests by Greenpeace activists and USSR's Nordic neighbors do not make this site attractive. The author feels that this movement in the USSR has set in motion a politically dynamic situation that makes for the best chance for a comprehensive test ban treaty yet witnessed

Analysis of North Korea's Nuclear Tests under Prospect Theory

International Nuclear Information System (INIS)

Lee, Han Myung; Ryu, Jae Soo; Lee, Kwang Seok; Lee, Dong Hoon; Jun, Eunju; Kim, Mi Jin

2013-01-01

North Korea has chosen nuclear weapons as the means to protect its sovereignty. Despite international society's endeavors and sanctions to encourage North Korea to abandon its nuclear ambition, North Korea has repeatedly conducted nuclear testing. In this paper, the reason for North Korea's addiction to a nuclear arsenal is addressed within the framework of cognitive psychology. The prospect theory addresses an epistemological approach usually overlooked in rational choice theories. It provides useful implications why North Korea, being under a crisis situation has thrown out a stable choice but taken on a risky one such as nuclear testing. Under the viewpoint of prospect theory, nuclear tests by North Korea can be understood as follows: The first nuclear test in 2006 is seen as a trial to escape from loss areas such as financial sanctions and regime threats; the second test in 2009 was interpreted as a consequence of the strategy to recover losses by making a direct confrontation against the United States; and the third test in 2013 was understood as an attempt to strengthen internal solidarity after Kim Jong-eun inherited the dynasty, as well as to enhance bargaining power against the United States. Thus, it can be summarized that Pyongyang repeated its nuclear tests to escape from a negative domain and to settle into a positive one. In addition, in the future, North Korea may not be willing to readily give up its nuclear capabilities to ensure the survival of its own regime

Test facilities for evaluating nuclear thermal propulsion systems

International Nuclear Information System (INIS)

Beck, D.F.; Allen, G.C.; Shipers, L.R.; Dobranich, D.; Ottinger, C.A.; Harmon, C.D.; Fan, W.C.; Todosow, M.

1992-01-01

Interagency panels evaluating nuclear thermal propulsion (NTP) development options have consistently recognized the need for constructing a major new ground test facility to support fuel element and engine testing. This paper summarizes the requirements, configuration, and baseline performance of some of the major subsystems designed to support a proposed ground test complex for evaluating nuclear thermal propulsion fuel elements and engines being developed for the Space Nuclear Thermal Propulsion (SNTP) program. Some preliminary results of evaluating this facility for use in testing other NTP concepts are also summarized

Properties of SYNROC C nuclear-waste form: a state-of-the-art review

International Nuclear Information System (INIS)

Oversby, V.M.

1982-09-01

SYNROC C is a titanate ceramic waste form designed to contain the waste generated by the reprocessing of commercial nuclear reactor fuel. The properties of SYNROC C are described with particular emphasis on the distribution of chemical elements in SYNROC, the fabrication of good quality specimens, and the chemical durability of SYNROC. Data obtained from testing of natural mineral analogues of SYNROC minerals are briefly discussed. The information available on radiation effects in SYNROC in relation to structural alteration and changes in chemical durability are summarized. 26 references, 2 figures, 18 tables

Standard test methods for determining chemical durability of nuclear, hazardous, and mixed waste glasses and multiphase glass ceramics: The product consistency test (PCT)

CERN Document Server

American Society for Testing and Materials. Philadelphia

2002-01-01

1.1 These product consistency test methods A and B evaluate the chemical durability of homogeneous glasses, phase separated glasses, devitrified glasses, glass ceramics, and/or multiphase glass ceramic waste forms hereafter collectively referred to as “glass waste forms” by measuring the concentrations of the chemical species released to a test solution. 1.1.1 Test Method A is a seven-day chemical durability test performed at 90 ± 2°C in a leachant of ASTM-Type I water. The test method is static and conducted in stainless steel vessels. Test Method A can specifically be used to evaluate whether the chemical durability and elemental release characteristics of nuclear, hazardous, and mixed glass waste forms have been consistently controlled during production. This test method is applicable to radioactive and simulated glass waste forms as defined above. 1.1.2 Test Method B is a durability test that allows testing at various test durations, test temperatures, mesh size, mass of sample, leachant volume, a...

The role of inertial containment fusion in replacing nuclear tests

Energy Technology Data Exchange (ETDEWEB)

Schaper, Annette [Hessische Stiftung Friedens- und Konfliktforschung, Frankfurt am Main (Germany)

2008-07-01

Nuclear weapon physicists need to understand the process of a nuclear explosion, and their major experimental tools had been nuclear tests. Since a couple of years, the established nuclear weapon states observe a testing moratorium. Nevertheless, they still want to keep their nuclear arsenals, and consequently to ensure the reliability, safety, and security of their nuclear warheads. For this purpose, they use experimental tools that replace nuclear tests, among them ICF. ICF plays a central role in the so-called ''stockpile stewardship program'' that the U.S. has implemented when it participated in the negotiations on a Comprehensive Test Ban Treaty. Several questions arise and are discussed in the presentation: Does ICF allow to simulate the extreme conditions of a nuclear explosion? Which are the functions of nuclear testing that ICF can replace and which are beyond its capabilities? Would ICF be a useful tool for the design of new nuclear warheads? Why are so huge sums spent on ICF in a military context although the usefulness for nuclear weapons seems rather limited?.

Testing to evaluate the suitability of waste forms developed for electrometallurgically treated spent sodium-bonded nuclear fuel for disposal in the Yucca Mountain reporsitory.

Energy Technology Data Exchange (ETDEWEB)

Ebert, W. E.

2006-01-31

The results of laboratory testing and modeling activities conducted to support the development of waste forms to immobilize wastes generated during the electrometallurgical treatment of spent sodium-bonded nuclear fuel and their qualification for disposal in the federal high-level radioactive waste repository are summarized in this report. Tests and analyses were conducted to address issues related to the chemical, physical, and radiological properties of the waste forms relevant to qualification. These include the effects of composition and thermal treatments on the phase stability, radiation effects, and methods for monitoring product consistency. Other tests were conducted to characterize the degradation and radionuclide release behaviors of the ceramic waste form (CWF) used to immobilize waste salt and the metallic waste form (MWF) used to immobilize metallic wastes and to develop models for calculating the release of radionuclides over long times under repository-relevant conditions. Most radionuclides are contained in the binder glass phase of the CWF and in the intermetallic phase of the MWF. The release of radionuclides from the CWF is controlled by the dissolution rate of the binder glass, which can be tracked using the same degradation model that is used for high-level radioactive waste (HLW) glass. Model parameters measured for the aqueous dissolution of the binder glass are used to model the release of radionuclides from a CWF under all water-contact conditions. The release of radionuclides from the MWF is element-specific, but the release of U occurs the fastest under most test conditions. The fastest released constituent was used to represent all radionuclides in model development. An empirical aqueous degradation model was developed to describe the dependence of the radionuclide release rate from a MWF on time, pH, temperature, and the Cl{sup -} concentration. The models for radionuclide release from the CWF and MWF are both bounded by the HLW glass

Examination plan for the soils and low-level radioactive waste forms of the NRC field testing lysimeters

International Nuclear Information System (INIS)

McConnell, J.W. Jr.; Rogers, R.D.; Jastrow, J.D.

1996-01-01

The Field Lysimeter Investigations: Low-Level Waste Data Base Development Program is obtaining information on the performance of radioactive waste forms. These experiments were recently shut down and have been examined in accordance with a detailed waste form and soil sampling plan. Ion-exchange resins from a commercial nuclear power station were solidified into waste forms using portland cement and vinyl ester-styrene. These waste forms were tested to (a) obtain information on performance of waste forms in typical disposal environments, (b) compare field results with bench leach studies, (c) develop a low-level waste data base for use in performance assessment source term calculations, and (d) apply the DUST computer code to compare predicted cumulative release to actual field data. The program, funded by the Nuclear Regulatory Commission (NRC), includes observed radionuclide releases from waste forms at two test sites over 10 years of successful operation. Lysimeters are ideal systems for obtaining actual field test data because, when properly designed and operated, they can be used to isolate soil and waste systems under actual environmental conditions. The purpose of this paper is to present the experimental plan for the examination of the waste forms and soils of the two lysimeter arrays, which have now been shut down. Vertical soil cores have been taken from the soil columns and will be analyzed with radiochemistry to define movement of radionuclides after release from the waste forms. A comparison is made of the DUST-predicted releases to those previously determined and reported from the lysimeter leachate analyses. That comparison uses new partition coefficients (Kd) recently obtained from laboratory analysis of the lysimeter soils and sand. Those DUST code results also will be compared to actual radionuclide movements through the soil columns as determined from soil core analysis

A novel waste form for disposal of spent-nuclear-fuel reprocessing waste: A vitrifiable cement

International Nuclear Information System (INIS)

Gougar, M.L.D.; Scheetz, B.E.; Siemer, D.D.

1999-01-01

A cement capable of being hot isostatically pressed into a glass ceramic has been proposed as the waste form for spent-nuclear-fuel reprocessing wastes at the Idaho National Engineering and Environmental Laboratory (INEEL). This intermediate cement, with a composition based on that of common glasses, has been designed and tested. The cement formulations included mixed INEEL wastes, blast furnace slag, reactive silica, and INEEL soil or vermiculite, which were activated with potassium or sodium hydroxide. Following autoclave processing, the cements were characterized. X-ray diffraction analysis revealed three notable crystalline phases: quartz, calcite, and fluorite. Results of compressive strength testing ranged from 1452 and 4163 psi, exceeding the US Nuclear Regulatory Commission (NRC)-suggested standard of >500 psi. From American National Standards Institute/American Nuclear Society 16.1-1986 leach testing, effective diffusivities for Cs were determined to be on the order of 10 -11 to 10 -10 cm 2 /s and for Sr were 10 -12 cm 2 /s, which are four orders of magnitude less than diffusivities in some other radwaste materials. Average leach indices (LI) were 9.6 and 11.9 for Cs and Sr, respectively, meeting the NRC Standard of LI > 6. The 28-day Materials Characterization Center-1 leach testing resulted in normalized elemental mass losses between 0.63 and 28 g/(m 2 ·day) for Cs and between 0.34 and 0.70 g/(m 2 ·day) industry-accepted standard while Cs losses indicate a process sensitive parameter

Further limitations on nuclear testing

International Nuclear Information System (INIS)

Brown, P.S.

1991-11-01

This document addresses a number of subjects related to further constraints on nuclear testing, briefly discussing each of the following topics: the current political situation, the kinds of steps that might next be taken in test limitations and the impacts of further testing limits, the need for a test ban readiness program, some issues related to verification, and the possibility of confidence building measures as alternative, or near-term, steps to further test limitations

Overall image of nuclear tests and their human effects at semipalatinsk. An attempt at analyses based on verbal data

International Nuclear Information System (INIS)

Matsuo, Masatsugu; Kawano, Noriyuki; Satoh, Kenichi; Apsalikov, Kazbek N.; Moldagaliev, Targat

2006-01-01

The present paper is part of an attempt at finally reconstructing the realities of nuclear tests and their human effects near Semipalatinsk, Kazakhstan. As a first step, it tries to reconstruct the overall image of nuclear tests and their human effects. Our data are 199 written testimonies of those affected by radiation, which were collected in 2002 and 2003. We statistically processed them, and categorized those words and expressions, which occurred most frequently in the testimonies, and obtained some forty categories, which represent the experiences, feelings, desires of those affected by radiation. Next, we conducted a principal component analysis of the categories. The result shows: (1) The experiences of the nuclear tests are arranged along the time axis, with direct experiences of the nuclear tests forming one coherent part of the perception and memory, and with other subsequent experiences forming another. (2) Of the latter, we can discern a core of the experiences on human effects such as 'disease,' 'death,' family,' 'radiation,' and so on. (3) And around this core, we see two different trends: one pointing to the current distress and plight, and the other pointing to future fear and hope. (author)

Solution exchange corrosion testing with the glass-zeolite ceramic waste form in demineralized water at 900C

International Nuclear Information System (INIS)

Simpson, L. J.

1998-01-01

A ceramic waste form of glass-bonded zeolite is being developed for the long-term disposition of fission products and transuranic elements in wastes from the U.S. Department of Energy's spent nuclear fuel conditioning activities. Solution exchange corrosion tests were performed on the ceramic waste form and its potential base constituents of glass, zeolite 5A, and sodalite as part of an effort to qualify the ceramic waste form for acceptance into the Civilian Radioactive Waste Management System. Solution exchange tests were performed at 90 C by replacing 80 to 90% of the leachate with fresh demineralized water after set time intervals. The results from these tests provide information about corrosion mechanisms and the ability of the ceramic waste form and its constituent materials to retain waste components. The results from solution exchange tests indicate that radionuclides will be preferentially retained in the zeolites without the glass matrix and in the ceramic waste form, with respect to cations like Li, K, and Na. Release results have been compared for simulated waste from candidate ceramic waste forms with zeolite 5A and its constituent materials to determine the corrosion behavior of each component

French nuclear plant safeguard pump qualification testing: EPEC test loop

International Nuclear Information System (INIS)

Guesnon, H.

1985-01-01

This paper reviews the specifications to which nuclear power plant safeguard pumps must be qualified, and surveys the qualification methods and program used in France to verify operability of the pump assembly and major pump components. The EPEC test loop is described along with loop capabilities and acheivements up to now. This paper shows, through an example, the Medium Pressure Safety Injection Pump designed for service in 1300 MW nuclear power plants, and the interesting possibilities offered by qualification testing

Melt-Dilute Form of AI-Based Spent Nuclear Fuel Disposal Criticality Summary Report

International Nuclear Information System (INIS)

D. Vinson; A. Serika

2002-01-01

Criticality analysis of the proposed melt-dilute (MD) form of aluminum-based spent nuclear fuel (SNF), under geologic repository conditions, was performed [1] following the methodology documented in the Disposal Criticality Analysis Methodology Topical Report [2]. This methodology evaluates the potential for nuclear criticality for a waste form in a waste package. Criticality calculations show that even with waste package failure, followed by degradation of material within the waste package and potential loss of neutron absorber materials, sub-critical conditions can be readily demonstrated for the MD form of aluminum-based SNF

Xenon monitoring and the Comprehensive Nuclear-Test-Ban Treaty

Energy Technology Data Exchange (ETDEWEB)

Bowyer, Theodore W. [Nuclear Explosion Monitoring Program, Pacific Northwest National Laboratory, Richland, Washington 99352 (United States)

2014-05-09

How do you monitor (verify) a CTBT? It is a difficult challenge to monitor the entire world for nuclear tests, regardless of size. Nuclear tests 'normally' occur underground, above ground or underwater. Setting aside very small tests (let's limit our thinking to 1 kiloton or more), nuclear tests shake the ground, emit large amounts of radioactivity, and make loud noises if in the atmosphere (or hydroacoustic waves if underwater)

Upgrade and Development of Nuclear Data Production Test Facility

Energy Technology Data Exchange (ETDEWEB)

NONE

2007-04-15

It is necessary to improve the Pohang Neutron Facility (PNF) in order to be used as a nuclear data production facility for users in both domestic and abroad. We improved following items: (1) upgrade the electron linac, (2) collimators inside the TOF beam pipe, (3) the development and installation of an automatic sample changer, (4) the extension of the TOF beam line, and (5) the data acquisition system. We would like to establish a utilization system for users to measure the nuclear data at the PNF. To do this, we made manuals for the accelerator operation and the data acquisition system. We also made an application form to apply for users to measure the nuclear data in both domestic and abroad. The main object of the Pohang Neutron Facility is to measure the nuclear data in the neutron energy region from thermal neutron to few hundreds of eV. In addition to neutron beams produced at the PNF, photon and electron beams are produced in this facility. We thus utilize this facility for other fields, such as test facility for detectors, activation experiments, polarized neutron beam source, and so on. In addition to these, we could use this facility for training students

Proving test on the reliability for nuclear valves

International Nuclear Information System (INIS)

Kajiyama, Yasuo; Tashiro, Hisao; Uga, Takeo; Maeda, Shunichi.

1986-01-01

Since valves are the most common components, they could be the most frequent causes of troubles in nuclear power plants. This proving test, therefore, has an important meaning to examine and verify the reliability of various valves under simulating conditions of abnormal and transient operations of the nuclear power plant. The test was performed mainly for the various types and pressure ratings of valves which were used in the primary and secondary systems in BWR and PWR nuclear power plants and which had major operating or safety related functions in those nuclear power plants. The results of the proving test, confirmed for more than four years, showed relatively favourable performance of the tested valves. It is concluded that performances of valves including operability, seat sealing and structural integrity were proved under the thermal cycling, vibration and pipe reaction load conditions. Operating functions during and after accident such as loss of coolant accident were satisfactory. From these results, it was considered that the purpose of this proving test was satisfactorily fulfilled. Several data accumulated by the test would be useful to get better reliability if it was evaluated with the actually experienced data of valves in the nuclear power plants. (Nogami, K.)

Nuclear cask testing films misleading and misused

Energy Technology Data Exchange (ETDEWEB)

Audin, L. (Audin (Lindsay), Ossining, NY (United States))

1991-10-01

In 1977 and 1978, Sandia National Laboratories, located in Albuquerque, New Mexico, and operated for the US Department of Energy (DOE), filmed a series of crash and fire tests performed on three casks designed to transport irradiated nuclear fuel assemblies. While the tests were performed to assess the applicability of scale and computer modeling techniques to actual accidents, films of them were quickly pressed into service by the DOE and nuclear utilities as proof'' to the public of the safety of the casks. In the public debate over the safety of irradiated nuclear fuel transportation, the films have served as the mainstay for the nuclear industry. Although the scripts of all the films were reviewed by USDOE officials before production, they contain numerous misleading concepts and images, and omit significant facts. The shorter versions eliminated qualifying statements contained in the longer version, and created false impressions. This paper discusses factors which cast doubt on the veracity of the films and the results of the tests.

Nuclear cask testing films misleading and misused

Energy Technology Data Exchange (ETDEWEB)

Audin, L. [Audin (Lindsay), Ossining, NY (United States)

1991-10-01

In 1977 and 1978, Sandia National Laboratories, located in Albuquerque, New Mexico, and operated for the US Department of Energy (DOE), filmed a series of crash and fire tests performed on three casks designed to transport irradiated nuclear fuel assemblies. While the tests were performed to assess the applicability of scale and computer modeling techniques to actual accidents, films of them were quickly pressed into service by the DOE and nuclear utilities as ``proof`` to the public of the safety of the casks. In the public debate over the safety of irradiated nuclear fuel transportation, the films have served as the mainstay for the nuclear industry. Although the scripts of all the films were reviewed by USDOE officials before production, they contain numerous misleading concepts and images, and omit significant facts. The shorter versions eliminated qualifying statements contained in the longer version, and created false impressions. This paper discusses factors which cast doubt on the veracity of the films and the results of the tests.

Nuclear cask testing films misleading and misused

International Nuclear Information System (INIS)

Audin, L.

1991-10-01

In 1977 and 1978, Sandia National Laboratories, located in Albuquerque, New Mexico, and operated for the US Department of Energy (DOE), filmed a series of crash and fire tests performed on three casks designed to transport irradiated nuclear fuel assemblies. While the tests were performed to assess the applicability of scale and computer modeling techniques to actual accidents, films of them were quickly pressed into service by the DOE and nuclear utilities as ''proof'' to the public of the safety of the casks. In the public debate over the safety of irradiated nuclear fuel transportation, the films have served as the mainstay for the nuclear industry. Although the scripts of all the films were reviewed by USDOE officials before production, they contain numerous misleading concepts and images, and omit significant facts. The shorter versions eliminated qualifying statements contained in the longer version, and created false impressions. This paper discusses factors which cast doubt on the veracity of the films and the results of the tests

Residual radioactivity in the soil of the Semipalatinsk Nuclear Test Site in the former USSR.

Science.gov (United States)

Yamamoto, M; Tsukatani, T; Katayama, Y

1996-08-01

This paper deals with our efforts to survey residual radioactivity in the soil sampled at the Semipalatinsk Nuclear Test Site and at off-site areas in Kazakhstan. The soil was sampled at the hypocenter where the first Soviet nuclear explosion was carried out on 29 August 1949, and at the bank of the crater called "Bolapan," which was formed by an underground nuclear detonation on 15 January 1965 along the Shagan River. As a comparison, other soil was also sampled in the cities of Kurchatov and Almaty. These data have allowed a preliminary evaluation of the contemporary radioactive contamination of the land in and around the test site. At the first nuclear explosion site and at Bolapan, higher than background levels of 239,240Pu with weapons-grade plutonium were detected together with fission and activation products such as 137Cs, 60Co, 152Eu, and 154Eu.

Leaching of nuclear power reactor wastes forms

International Nuclear Information System (INIS)

Endo, L.S.; Villalobos, J.P.; Miyamoto, H.

1986-01-01

The leaching tests for power reactor wastes carried out at IPEN/CNEN-SP are described. These waste forms consist mainly of spent resins and boric acid concentrates solidified in ordinary Portland cement. All tests were conducted according to the ISO and IAEA recommendations. 3 years leaching results are reported, determining cesium and strontium diffusivity coefficients for boric acid waste form and ion-exchange resins. (Author) [pt

Some Qualitative Requirements for Testing of Nuclear Emergency Response Robots

International Nuclear Information System (INIS)

Eom, Heungseop; Cho, Jai Wan; Choi, Youngsoo; Jeong, Kyungmin

2014-01-01

Korea Atomic Energy Research Institute (KAERI) is carrying out the project 'Development of Core Technology for Remote Response in Nuclear Emergency Situation', and as a part of the project, we are studying the reliability and performance requirements of nuclear emergency response robots. In this paper, we described some qualitative requirements for testing of nuclear emergency response robots which are different to general emergency response robots. We briefly introduced test requirements of general emergency response robots and described some qualitative aspects of test requirements for nuclear emergency response robots. When considering an immature field-robot technology and variety of nuclear emergency situations, it seems hard to establish quantitative test requirements of these robots at this time. However, based on studies of nuclear severe accidents and the experience of Fukushima NPP accident, we can expect some test requirements including quantitative ones for nuclear emergency response robots

Lubricant Test Methods for Sheet Metal Forming

DEFF Research Database (Denmark)

Bay, Niels; Olsson, David Dam; Andreasen, Jan Lasson

2008-01-01

appearing in different sheet forming operations such as stretch forming, deep drawing, ironing and punching. The laboratory tests have been especially designed to model the conditions in industrial production. Application of the tests for evaluating new lubricants before introducing them in production has......Sheet metal forming of tribologically difficult materials such as stainless steel, Al-alloys and Ti-alloys or forming in tribologically difficult operations like ironing, punching or deep drawing of thick plate requires often use of environmentally hazardous lubricants such as chlorinated paraffin...... oils in order to avoid galling. The present paper describes a systematic research in the development of new, environmentally harmless lubricants focusing on the lubricant testing aspects. A system of laboratory tests has been developed to study the lubricant performance under the very varied conditions...

Bees Algorithm for Construction of Multiple Test Forms in E-Testing

Science.gov (United States)

Songmuang, Pokpong; Ueno, Maomi

2011-01-01

The purpose of this research is to automatically construct multiple equivalent test forms that have equivalent qualities indicated by test information functions based on item response theory. There has been a trade-off in previous studies between the computational costs and the equivalent qualities of test forms. To alleviate this problem, we…

Full scale vibration test on nuclear power plant auxiliary building: Part I

International Nuclear Information System (INIS)

Langer, V.; Tinic, S.; Berger, E.; Zwicky, P.; Prater, E.G.

1987-01-01

In connection with the construction of the reinforced concrete auxiliary building housing the two boric water tanks (so-called BOTA building) of the Beznau Nuclear Power Plant in Switzerland the opportunity was given to carry out full scale vibration tests in November 1985. The overall aim of the tests was to validate computational models and parameters widely used in the seismic analysis of the structures and critical components of nuclear power plants. The scope of the experimental investigation was the determination of the eigenfrequencies and damping values for the fundamental soil-structure interaction (SSI) modes. The excitation level was aimed to be as high as feasibly possible. A working group was formed of representatives of the owner, NOK, the consulting firm Basler and Hofmann and the ETH to supervise the project. The project's main phases were the planning and execution of the tests, the evaluation of recorded data, numerical simulation of the tests using different computer models and finally the comparison and interpretation of measured and computed results

Test procedure forms for sludge retrieval and packaging

International Nuclear Information System (INIS)

Feigenbutz, L.V.

1994-01-01

This document provides test procedure forms for sludge retrieval and packaging tests in the 305 Cold Test Facility. The completed and approved forms provide all descriptions, criteria and analysis to safely perform sludge equipment tests in the 305 Cold Test Facility

Testing of nuclear air-cleaning systems

International Nuclear Information System (INIS)

Anon.

1975-01-01

A standard is presented which describes methods for field-testing nuclear power plant air cleaning systems. Included are specifications for visual inspection; duct and housing leak test; mounting frame pressure leak test; airflow capacity, distribution, and residence time tests; air-aerosol mixing uniformity test; in place leak test of HEPA filter banks; multiple sampling technique; in-place leak test of adsorber stage; laboratory testing of adsorbent; and duct heater performance test

Field test of wireless sensor network in the nuclear environment

International Nuclear Information System (INIS)

Li, L.; Wang, Q.; Bari, A.; Deng, C.; Chen, D.; Jiang, J.; Alexander, Q.; Sur, B.

2014-01-01

Wireless sensor networks (WSNs) are appealing options for the health monitoring of nuclear power plants due to their low cost and flexibility. Before they can be used in highly regulated nuclear environments, their reliability in the nuclear environment and compatibility with existing devices have to be assessed. In situ electromagnetic interference tests, wireless signal propagation tests, and nuclear radiation hardness tests conducted on candidate WSN systems at AECL Chalk River Labs are presented. The results are favourable to WSN in nuclear applications. (author)

Field test of wireless sensor network in the nuclear environment

Energy Technology Data Exchange (ETDEWEB)

Li, L., E-mail: lil@aecl.ca [Atomic Energy of Canada Limited, Chalk River, Ontario (Canada); Wang, Q.; Bari, A. [Univ. of Western Ontario, London, Ontario (Canada); Deng, C.; Chen, D. [Univ. of Electronic Science and Technology of China, Chengdu, Sichuan (China); Jiang, J. [Univ. of Western Ontario, London, Ontario (Canada); Alexander, Q.; Sur, B. [Atomic Energy of Canada Limited, Chalk River, Ontario (Canada)

2014-06-15

Wireless sensor networks (WSNs) are appealing options for the health monitoring of nuclear power plants due to their low cost and flexibility. Before they can be used in highly regulated nuclear environments, their reliability in the nuclear environment and compatibility with existing devices have to be assessed. In situ electromagnetic interference tests, wireless signal propagation tests, and nuclear radiation hardness tests conducted on candidate WSN systems at AECL Chalk River Labs are presented. The results are favourable to WSN in nuclear applications. (author)

Australia: Comprehensive Nuclear Test Ban Treaty. Model Treaty text

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-02-01

The scope of the proposed Treaty includes the following: Each State Party undertakes not to carry out any nuclear weapon test explosion, and to prohibit and prevent any such nuclear explosion at any place under its jurisdiction or control; each State Party undertakes, furthermore, to refrain from causing, encouraging, or in any way participating in the carrying out of any nuclear weapon tests explosion or any other nuclear explosion

Sol-gel technology applied to crystalline ceramic nuclear waste forms

International Nuclear Information System (INIS)

Angelini, P.; Bond, W.D.; Caputo, A.J.; Mack, J.E.; Lackey, W.J.; Lee, D.A.; Stinton, D.P.

1980-01-01

The sol-gel process is being developed for the solidification and isolation of high-level nuclear fuel waste. Three gelation methods are being developed for producing alternative waste forms. These include internal gelation for producing spheres of up to 1 mm diam suitable for coating, external gelation, and water extraction methods for producing material suitable for alternate ceramic processing. In this study internal gelation has been used to produce ceramic spheres of various alternative nuclear waste compositions. A gelation system capable of producing 100-g batches has been assembled and used for development. Waste forms containing up to 70 wt % simulated Savannah River Plant waste have been produced. Dopants such as Cs, Sr, Nd, Ru, and Mo were used in some experiments to observe side waste streams and sintering effects. Synroc microspheres were coated with both low-density carbon, high-density impermeable carbon, high-temperature dense SiC, and SiC deposited at temperatures near 900 0 C. Other gelation methods and other alternative waste forms are being developed

The Nuclear Non-Proliferation Treaty and the Comprehensive Nuclear-Test-Ban Treaty, the relationship

Energy Technology Data Exchange (ETDEWEB)

Graham, Thomas Jr. [7609 Glenbrook Rd., Bethesda, MD 20814 (United States)

2014-05-09

The Nuclear Non-Proliferation Treaty (NPT) is the most important international security arrangement that we have that is protecting the world community and this has been true for many years. But it did not happen by accident, it is a strategic bargain in which 184 states gave up the right forever to acquire the most powerful weapon ever created in exchange for a commitment from the five states allowed to keep nuclear weapons under the NPT (U.S., U.K., Russia, France and China), to share peaceful nuclear technology and to engage in disarmament negotiations aimed at the ultimate elimination of their nuclear stockpiles. The most important part of this is the comprehensive nuclear test ban (CTBT); the thinking by the 184 NPT non-nuclear weapon states was and is that they understand that the elimination of nuclear weapon stockpiles is a long way off, but at least the NPT nuclear weapon states could stop testing the weapons. The CTBT has been ratified by 161 states but by its terms it can only come into force if 44 nuclear potential states ratify; 36 have of the 44 have ratified it, the remaining eight include the United States and seven others, most of whom are in effect waiting for the United States. No state has tested a nuclear weapon-except for complete outlier North Korea-in 15 years. There appears to be no chance that the U.S. Senate will approve the CTBT for ratification in the foreseeable future, but the NPT may not survive without it. Perhaps it is time to consider an interim measure, for the UN Security Council to declare that any future nuclear weapon test any time, anywhere is a 'threat to peace and security', in effect a violation of international law, which in today's world it clearly would be.

Low-level radioactive waste form qualification testing

International Nuclear Information System (INIS)

Sohal, M.S.; Akers, D.W.

1998-06-01

This report summarizes activities that have already been completed as well as yet to be performed by the Idaho National Engineering and Environmental Laboratory (INEEL) to develop a plan to quantify the behavior of radioactive low-level waste forms. It briefly describes the status of various tasks, including DOE approval of the proposed work, several regulatory and environmental related documents, tests to qualify the waste form, preliminary schedule, and approximate cost. It is anticipated that INEEL and Brookhaven National Laboratory will perform the majority of the tests. For some tests, services of other testing organizations may be used. It should take approximately nine months to provide the final report on the results of tests on a waste form prepared for qualification. It is anticipated that the overall cost of the waste quantifying service is approximately $150,000. The following tests are planned: compression, thermal cycling, irradiation, biodegradation, leaching, immersion, free-standing liquid tests, and full-scale testing

Low-level radioactive waste form qualification testing

Energy Technology Data Exchange (ETDEWEB)

Sohal, M.S.; Akers, D.W.

1998-06-01

This report summarizes activities that have already been completed as well as yet to be performed by the Idaho National Engineering and Environmental Laboratory (INEEL) to develop a plan to quantify the behavior of radioactive low-level waste forms. It briefly describes the status of various tasks, including DOE approval of the proposed work, several regulatory and environmental related documents, tests to qualify the waste form, preliminary schedule, and approximate cost. It is anticipated that INEEL and Brookhaven National Laboratory will perform the majority of the tests. For some tests, services of other testing organizations may be used. It should take approximately nine months to provide the final report on the results of tests on a waste form prepared for qualification. It is anticipated that the overall cost of the waste quantifying service is approximately $150,000. The following tests are planned: compression, thermal cycling, irradiation, biodegradation, leaching, immersion, free-standing liquid tests, and full-scale testing.

Nuclear instrumentation system operating experience and nuclear instrument testing in the EBR-II

International Nuclear Information System (INIS)

Yingling, G.E.; Curran, R.N.

1980-01-01

In March of 1972 three wide range nuclear channels were purchased from Gulf Atomics Corporation and installed in EBR-II as a test. The three channels were operated as a test until April 1975 when they became a permanent part of the reactor shutdown system. Also described are the activities involved in evaluating and qualifying neutron detectors for LMFBR applications. Included are descriptions of the ANL Components Technology Division Test Program and the EBR-II Nuclear Instrument Test Facilities (NITF) used for the in-reactor testing and a summary of program test results from EBR-II

Residual radioactivity in the soil of the Semipalatinsk Nuclear Test Site in the former USSR

International Nuclear Information System (INIS)

Yamamoto, Masayoshi; Tsukatani, Tsuneo; Katayama, Yukio

1996-01-01

This paper deals with our efforts to survey residual readioactivity in the soil sampled at teh Semipalatinsk Nuclear Test Site and at off-site areas in Kazakhstan. The soil sampled at the hypocenter where the first Soviet nuclear explosion was carried out on 29 August 1949, and at the bank of the crater called open-quotes Bolapan,close quotes which was formed by an underground nuclear detonation on 15 January 1965 along the Shagan River. As a comparison, other soil was also sampled in the cities of Kurchatov and Almaty. These data have allowed a preliminary evaluation of the contemporary radioactive contamination of the land in and around the test site. At the first nuclear explosion site and at Bolapan, higher than background levels of 239,240 Pu with weapons-grade plutonium were detected together with fission and activation products such as 137 Cs, 60 Co, 152 Eu, and 154 Eu. 20 refs., 3 figs., 5 tabs

Nuclear waste package materials testing report: basaltic and tuffaceous environments

International Nuclear Information System (INIS)

Bradley, D.J.; Coles, D.G.; Hodges, F.N.; McVay, G.L.; Westerman, R.E.

1983-03-01

The disposal of high-level nuclear wastes in underground repositories in the continental United States requires the development of a waste package that will contain radionuclides for a time period commensurate with performance criteria, which may be up to 1000 years. This report addresses materials testing in support of a waste package for a basalt (Hanford, Washington) or a tuff (Nevada Test Site) repository. The materials investigated in this testing effort were: sodium and calcium bentonites and mixtures with sand or basalt as a backfill; iron and titanium-based alloys as structural barriers; and borosilicate waste glass PNL 76-68 as a waste form. The testing also incorporated site-specific rock media and ground waters: Reference Umtanum Entablature-1 basalt and reference basalt ground water, Bullfrog tuff and NTS J-13 well water. The results of the testing are discussed in four major categories: Backfill Materials: emphasizing water migration, radionuclide migration, physical property and long-term stability studies. Structural Barriers: emphasizing uniform corrosion, irradiation-corrosion, and environmental-mechanical testing. Waste Form Release Characteristics: emphasizing ground water, sample surface area/solution volume ratio, and gamma radiolysis effects. Component Compatibility: emphasizing solution/rock, glass/rock, glass/structural barrier, and glass/backfill interaction tests. This area also includes sensitivity testing to determine primary parameters to be studied, and the results of systems tests where more than two waste package components were combined during a single test

Alternate nuclear waste forms and interactions in geologic media

International Nuclear Information System (INIS)

Boatner, L.A.; Battle, G.C. Jr.

1981-04-01

The primary purposes of the conference on Alternate Nuclear Waste Forms and Interactions in Geologic Media were: First, to provide an opportunity for a review of the status of the research on some of the candidate alternative waste forms; second, to provide an opportunity for comparing the characteristics of alternate waste forms to those of glasses; and third, to stimulate increased interactions between those research groups that were engaged in a more basic approach to characterizing waste forms and those who were concerned with more applied aspects such as the processing of these materials. The motivating philosophy behind this third purpose of the conference was based on the idea that by operating from the soundest possible fundamental base for any of the candidate waste forms, hopefully any future unpleasant surprise - such as that alluded to earlier in the case of glass waste forms - could be avoided. Separate abstracts have been prepared for individual papers for inclusion in the Energy Data Base

Environmental contamination due to nuclear weapon tests and peaceful uses of nuclear explosions

International Nuclear Information System (INIS)

Petr, I.; Jandl, J.

1979-01-01

The effect of nuclear weapons tests and of the peaceful uses of nuclear explosions on the environment is described. The local and global fallout and the fallout distribution are analysed for the weapon tests. The radiation effects of external and internal irradiation on the population are discussed and the overall radiation risk is estimated. (author)

10 CFR 140.91 - Appendix A-Form of nuclear energy liability policy for facilities.

Science.gov (United States)

2010-01-01

... 10 Energy 2 2010-01-01 2010-01-01 false Appendix A-Form of nuclear energy liability policy for facilities. 140.91 Section 140.91 Energy NUCLEAR REGULATORY COMMISSION (CONTINUED) FINANCIAL PROTECTION... other matter not within the Commission's statutory jurisdiction under the Atomic Energy Act. Nuclear...

Reload Startup Physics Tests for Tianwan Nuclear Power station

International Nuclear Information System (INIS)

Yang Xiaoqiang; Li Wenshuang; Li Youyi; Yao Jinguo; Li Zaipeng Jiangsu

2010-01-01

This paper briefly describes the test purposes, test items, test schedules and test equipment's for reload startup physics test's on Unit 1 and 2 of Tianwan Nuclear Power station. Then, an overview of the previous thrice tests and evaluations on the tests results are presented. In the end, the paper shows the development and work direction of optimization project for reload startup physics tests on Unit 1 and 2 of Tianwan Nuclear Power station. (Authors)

Accuracy analysis of the CTBTO nuclear test detection scale and Improvement

Energy Technology Data Exchange (ETDEWEB)

Ryu, Young Kwang [Seoul National Univ., Seoul (Korea, Republic of)

2014-10-15

CTBTO (Comprehensive nuclear Test Ban Treaty Organization) is charge of nuclear test monitoring for nuclear non-proliferation. CTBTO has 170 seismic stations in operation in 76 countries in order to detect the artificial earthquake that was caused by an underground nuclear test. Korea use formula that is based on the equations that are used by the IMS (International Monitoring System) of CTBTO for analysis of explosive scale, and reflect the nature of the terrain, such as rock. But the expression for calculating the exact scale explosive is still un-established state. And generally CTBTO doesn't care about artificial explosive that is being received low-yield in accordance with the criteria of nuclear detection. But, at the time that North Korea conduct a nuclear test, it should not be overlooked that the scale of the earthquake detection criteria below. Because DPRK is trying to conceal their nuclear development capability, there are possibility of low-yield nuclear test or possibility of install a buffer to hide actual explosive scale. These radionuclide observations were consistent with a DPRK low-yield nuclear test on May 2010, even though no seismic signals from such a test have been detected. But there were a few times of low-yield (magnitude 1.39-1.93) occurred around DPRK nuclear test site at that time.

Geologic surface effects of underground nuclear testing, Yucca Flat, Nevada Test Site, Nevada; TOPICAL

International Nuclear Information System (INIS)

Grasso, D.N.

2000-01-01

This report presents a new Geographic Information System composite map of the geologic surface effects caused by underground nuclear testing in the Yucca Flat Physiographic Area of the Nevada Test Site, Nye County, Nevada. The Nevada Test Site (NTS) was established in 1951 as a continental location for testing nuclear devices (Allen and others, 1997, p.3). Originally known as the ''Nevada Proving Ground'', the NTS hosted a total of 928 nuclear detonations, of which 828 were conducted underground (U.S. Department of Energy, 1994). Three principal testing areas of the NTS were used: (1) Yucca Flat, (2) Pahute Mesa, and (3) Rainier Mesa including Aqueduct Mesa. Underground detonations at Yucca Flat and Pahute Mesa were typically emplaced in vertical drill holes, while others were tunnel emplacements. Of the three testing areas, Yucca Flat was the most extensively used, hosting 658 underground tests (747 detonations) located at 719 individual sites (Allen and others, 1997, p.3-4). Figure 1 shows the location of Yucca Flat and other testing areas of the NTS. Figure 2 shows the locations of underground nuclear detonation sites at Yucca Flat. Table 1 lists the number of underground nuclear detonations conducted, the number of borehole sites utilized, and the number of detonations mapped for surface effects at Yucca Flat by NTS Operational Area

The struggle of the veterans of the French nuclear tests

International Nuclear Information System (INIS)

2005-01-01

The question debated in this article concerns the demand of compensation and recognition of the impact on their health of nuclear tests. The military personnel that worked during nuclear tests in French Polynesia and the Sahara sites, but also the inhabitants of the atolls of Moruroa and Fangataufa equally in French Polynesia. An observatory of the veterans health has been created in order to improve the medical management of military personnel and former military personnel. An association 'Moruroa e tatou' contains the Polynesian former workers of the Nuclear tests of the Pacific and the association A.V.E.N. contains the veterans of nuclear tests. numerous examples are detailed. The question is tackled too for the consequences on health of the British nuclear tests, in Australia, Christmas Islands, and New Zealand. (N.C.)

Study of nuclear fuel powders forming by axial compaction

International Nuclear Information System (INIS)

Fourcade, J.

2002-12-01

Nuclear fuel powders forming, although perfectly dominated, fail to make compacts without density gradients. Density heterogeneities induce diametric deformations during firing which force manufacturers to adjust shape with a high cost machining stage. Manufacturing process improvement is a major project to obtain perfectly shaped pellets and reduce their cost. One way of investigation of this project is the study of powders compaction mechanisms to understand and improve their behaviour. The goal of this study is to identify the main mechanisms linked with powder properties that act on pressing. An empirical model is developed to predict pellet deformations from a single compaction test. This model has to link powder properties with their compaction behaviour. Then, compaction tests identify the main mechanisms whereas a contact dynamic program is used to explain them. These works, done to improve the understanding in powders behaviour, focus on powders agglomeration state and macroscopic particles arrangement during the die filling stage. Actually, for granulated powders, granules cohesion act on the powder bed behaviour under pressure. The first particles arrangement is responsible for the first transfer directions into the powder and so for its transfer homogeneity and isotropy. As a consequence, the knowledge of all the macroscopic powder properties is essential to understand and improve the manufacturing process. Moreover, tests on UO 2 powders have shown that it is better to use granulated powders with spherical granules, short size distribution and granules cohesion according with compaction pressure to improve compact homogeneity of densification. (author)

Determination of chemical forms of C-14 in liquid discharges from nuclear power plants

Czech Academy of Sciences Publication Activity Database

Světlík, Ivo; Fejgl, M.; Povinec, P. P.; Kořínková, Tereza; Tomášková, Lenka; Pospíchal, J.; Kurfiřt, M.; Striegler, R.; Kaufmanová, M.

2017-01-01

Roč. 177, OCT (2017), s. 256-260 ISSN 0265-931X Institutional support: RVO:61389005 Keywords : analytical routines * dissolved organic forms of C-14 (DIC) * dissolved inorganic forms of C-14 (DOC) * Nuclear power plant (NPP) * liquid releases Subject RIV: DL - Nuclear Waste, Radioactive Pollution ; Quality OBOR OECD: Environment al sciences (social aspects to be 5.7) Impact factor: 2.310, year: 2016

Characteristics of acoustic wave from atmospheric nuclear explosions conducted at the USSR Test Sites

Science.gov (United States)

Sokolova, Inna

2015-04-01

Availability of the acoustic wave on the record of microbarograph is one of discriminate signs of atmospheric (surface layer of atmosphere) and contact explosions. Nowadays there is large number of air wave records from chemical explosions recorded by the IMS infrasound stations installed during recent decade. But there is small number of air wave records from nuclear explosions as air and contact nuclear explosions had been conducted since 1945 to 1962, before the Limited Test Ban Treaty was signed in 1963 (the treaty banning nuclear weapon tests in the atmosphere, in outer space and under water) by the Great Britain, USSR and USA. That time there was small number of installed microbarographs. First infrasound stations in the USSR appeared in 1954, and by the moment of the USSR collapse the network consisted of 25 infrasound stations, 3 of which were located on Kazakhstan territory - in Kurchatov (East Kazakhstan), in Borovoye Observatory (North Kazakhstan) and Talgar Observatory (Northern Tien Shan). The microbarograph of Talgar Observatory was installed in 1962 and recorded large number of air nuclear explosions conducted at Semipalatinsk Test Site and Novaya Zemlya Test Site. The epicentral distance to the STS was ~700 km, and to Novaya Zemlya Test Site ~3500 km. The historical analog records of the microbarograph were analyzed on the availability of the acoustic wave. The selected records were digitized, the database of acoustic signals from nuclear explosions was created. In addition, acoustic signals from atmospheric nuclear explosions conducted at the USSR Test Sites were recorded by analogue broadband seismic stations at wide range of epicentral distances, 300-3600 km. These signals coincide well by its form and spectral content with records of microbarographs and can be used for monitoring tasks and discrimination in places where infrasound observations are absent. Nuclear explosions which records contained acoustic wave were from 0.03 to 30 kt yield for

Method for forming microspheres for encapsulation of nuclear waste

Science.gov (United States)

Angelini, Peter; Caputo, Anthony J.; Hutchens, Richard E.; Lackey, Walter J.; Stinton, David P.

1984-01-01

Microspheres for nuclear waste storage are formed by gelling droplets containing the waste in a gelation fluid, transferring the gelled droplets to a furnace without the washing step previously used, and heating the unwashed gelled droplets in the furnace under temperature or humidity conditions that result in a substantially linear rate of removal of volatile components therefrom.

Sampling and transport of paraffin waste form from CWDS of nuclear power plant

International Nuclear Information System (INIS)

Lee, J. M.; Hwang, J. H.; Kim, C. R.; Park, J. W.

2000-01-01

Sampling and transport of paraffin waste form from concentrated waste drying system (CWDS) of domestic nuclear power plant were performed to collect the leaching characteristic data for the disposal of radioactive waste. Transport was performed according to the national regulations and the internal rules of the nuclear power plant. The sample of paraffin waste form was classified as L type package according to the regulation and radiation exposure of operator was measured in the range of 6 to 12 mrem that was less than the estimated amount

The Comprehensive Nuclear Test-ban Treaty : an overview

International Nuclear Information System (INIS)

1997-01-01

The Comprehensive Nuclear Test-Ban Treaty ushers in the post-nuclear testing era. The Treaty is the result of many years of intensive international negotiation, and is an impressive document of some 48 pages plus 15 pages of annexes which, by April 1997, 143 nations including New Zealand had signed. New Zealand has consistently maintained a strong opposition to the testing of nuclear weapons and has had a long involvement in negotiations towards this Treaty. This is the first of a series of articles on the Treaty, its enforcement, and its implications for New Zealand, and provides an overview of the treaty by means of a quick tour through its main provisions. (author)

Tritium as an indicator of venues for nuclear tests.

Science.gov (United States)

Lyakhova, O N; Lukashenko, S N; Mulgin, S I; Zhdanov, S V

2013-10-01

Currently, due to the Treaty on the Non-proliferation of Nuclear Weapons there is a highly topical issue of an accurate verification of nuclear explosion venues. This paper proposes to consider new method for verification by using tritium as an indicator. Detailed studies of the tritium content in the air were carried in the locations of underground nuclear tests - "Balapan" and "Degelen" testing sites located in Semipalatinsk Test Site. The paper presents data on the levels and distribution of tritium in the air where tunnels and boreholes are located - explosion epicentres, wellheads and tunnel portals, as well as in estuarine areas of the venues for the underground nuclear explosions (UNE). Copyright © 2013 Elsevier Ltd. All rights reserved.

Radiological criteria for underground nuclear tests

International Nuclear Information System (INIS)

Malik, J.S.; Brownlee, R.R.; Costa, C.F.; Mueller, H.F.; Newman, R.W.

1981-04-01

The radiological criteria for the conduct of nuclear tests have undergone many revisions with the current criteria being 0.17 rad for uncontrolled populations and 0.5 rad for controllable populations. Their effect upon operations at the Nevada Test Site and the current off-site protective plans are reviewed for areas surrounding the Site. The few accidental releases that have occurred are used to establish estimates of probability of release and of hazard to the population. These are then put into context by comparing statistical data on other accidents and cataclysms. The guidelines established by DOE Manual Chapter MC-0524 have never been exceeded during the entire underground nuclear test program. The probability of real hazard to off-site populations appears to be sufficiently low as not to cause undue concern to the citizenry

Radiological criteria for underground nuclear tests

Energy Technology Data Exchange (ETDEWEB)

Malik, J.S.; Brownlee, R.R.; Costa, C.F.; Mueller, H.F.; Newman, R.W.

1981-04-01

The radiological criteria for the conduct of nuclear tests have undergone many revisions with the current criteria being 0.17 rad for uncontrolled populations and 0.5 rad for controllable populations. Their effect upon operations at the Nevada Test Site and the current off-site protective plans are reviewed for areas surrounding the Site. The few accidental releases that have occurred are used to establish estimates of probability of release and of hazard to the population. These are then put into context by comparing statistical data on other accidents and cataclysms. The guidelines established by DOE Manual Chapter MC-0524 have never been exceeded during the entire underground nuclear test program. The probability of real hazard to off-site populations appears to be sufficiently low as not to cause undue concern to the citizenry.

Biodegradation testing of TMI-2 EPICOR-II waste forms

International Nuclear Information System (INIS)

Rogers, R.D.; McConnell, J.W. Jr.

1988-06-01

ASTM biodegradation tests were conducted on waste forms containing high specific activity ion exchange resins from EPICOR-II prefilters. Those tests were part of a program to test waste forms in accordance with the NRC Branch Technical Position on Waste Form. Small waste forms were manufactured using two different solidification agents, Portland Type I-II cement and vinyl ester-styrene (VES). Ion exchange material was taken from two EPICOR-II prefilters; PF-7, which contained all organic material, and PF-20, which contained organic resins and a layer of inorganic zeolites. Test results showed that the VES waste forms supported microbial growth, while cement waste forms did not support that growth. Growth was also observed adjacent to some VES waste forms. Radiation levels found in the ion exchange resins used in this study were not found to inhibit microbial growth. The extent of degradation of the waste forms could not be determined using the ASTM tests specified by the NRC Branch Technical Position on Waste Form. As a result of this work, a different testing methodology is recommended, which would provide direct verification of waste form capabilities. That methodology would evaluate solidification materials without using the ASTM procedures or subsequent compression testing. The proposed tests would provide exposure to a wide range of microbial species, use appropriately sized specimens, provide for possible use of alternate carbon sources, and extend the test length. Degradation would be determined directly by measuring metabolic activity or specimen weight loss. 16 refs., 15 figs., 3 tabs

A comparison of hydrogen with alternate energy forms from coal and nuclear energy

International Nuclear Information System (INIS)

Cox, K.E.

1976-01-01

Alternate energy forms that can be produced from coal and nuclear energy have been analyzed on efficiency, economic and end-use grounds. These forms include hydrogen, methane, electricity, and EVA-ADAM, a 'chemical heat pipe' approach to energy transmission. The EVA-ADAM system for nuclear heat appears to be economically competitive with the other energy carriers except over very large distances. The cost of hydrogen derived from coal is approximately equal to that of methane derived from the same source when compared on an equal BTU basis. Thermochemically derived hydrogen from nuclear energy shows a break-even range with hydrogen derived from coal at coal costs of from Pound33 to 80/ton depending on the cost of nuclear heat. Electricity and electrolytically derived hydrogen are the most expensive energy carriers and electricity's use should be limited to applications involving work rather than heat. Continued work in thermochemical hydrogen production schemes should be supported as an energy option for the future. (author)

Technical justifications for the tests and criteria in the waste form technical position appendix on cement stabilization

International Nuclear Information System (INIS)

Siskind, B.; Cowgill, M.G.

1992-01-01

As part of its technical assistance to the Nuclear Regulatory Commission (NRC), Brookhaven National Laboratory (BNL) developed a background document for the cement stabilization appendix, Appendix A, to Rev. 1 of the Technical Position on Waste Form (TP). Here we present an overview of this background document, which provides technical justification for the stability tests to be performed on cement-stabilized waste forms and for the criteria posed in each test, especially for those tests which have been changed from their counterparts in the May 1983 Rev. 0 TP. We address guidelines for procedures from Appendix A which are considered in less detail or not at all in the Rev. 0 of the TP, namely, qualification specimen preparation (mixing, curing, storage), statistical sampling and analysis, process control program specimen preparation and examination, and surveillance specimens. For each waste form qualification test, criterion or procedural guidelines, we consider the reason for its inclusion in Appendix A, the changes from Rev. 0 of the TP (if applicable), and a discussion of the justification or rationale for these changes

Technical justifications for the tests and criteria in the waste form Technical position appendix on cement stabilization

International Nuclear Information System (INIS)

Siskind, B.; Cowgill, M.G.

1992-01-01

As part of its technical assistance to the Nuclear Regulatory Commission (NRC), Brookhaven National Laboratory (BNL) developed a background document for the cement stabilization appendix. Appendix A, to Rev. 1 of the Technical Position on Waste Form (TP). Here we present an overview of this background document, which provides technical justification for the stability tests to be performed on cement-stabilized waste forms and for the criteria posed in each test) especially for those tests which have been changed from their counterparts in the May 1983 Rev. 0 TP. We address guidelines for procedures from Appendix A which are considered in less detail or not at all in the Rev. 0 of the TP, namely, qualification specimen preparation (mixing, curing, storage), statistical sampling and analysis, process control program specimen preparation and examination, and surveillance specimens. For each waste form qualification test, criterion or procedural guideline, we consider the reason for its inclusion in Appendix A, the changes from Rev. 0 of the TP (if applicable), and a discussion of the justification or rationale for these changes. (author)

Testing and evaluation of absorbers for gaseous penetrative forms of radioiodine

International Nuclear Information System (INIS)

Kabot, M.

1974-10-01

A significant fraction of airborne radioiodine, encountered at times in operational areas of Ontario Hydro nuclear power generating stations, was found to be penetrative inorganic and organic species. Theorectical evaluation of iodine chemistry is presented based on analysis of operational iodine concentrations in station systems, areas and effluents under actual operating conditions. The theoretical evaluation and the operational experiments show that hypoiodous acid and organic iodides are the basic forms of airborne iodine which occur in the field and in station effluents. A method was developed for laboratory generation of HOI and its identity confirmed by use of specific absorbers. Six of the commercially available (and recently developed) absorbers were tested for HOI removal efficiency in the laboratory under conditions similar to those found in the field. Experimental equipment, methods used for the absorber testing and experimental conditions are described. Results show that charcoals have generally better initial absorption efficiency for hypoiodous acid than silver impregnated inorganic absorbers. Both technical and economical aspects of the operational use of the tested absorbers are discussed. (auth)

Benchmark test of MORSE-DD code using double-differential form cross sections

International Nuclear Information System (INIS)

Nakagawa, Masayuki; Mori, Takamasa; Ishiguro, Yukio

1985-02-01

The multi-group double-differential form cross sections (DDX) and the three dimensional Monte Carlo code MORSE-DD devised to utilize the DDX, which were developed for the fusion neutronics analysis, have been validated through many benchmark tests. All the problems tested have a 14 MeV neutron source. To compare the calculated results with the measured values, the following experiments were adopted as the benchmark problems; leakage neutron spectra from spheres composed of nine kinds of materials measured at LLNL, neutron angular spectra from the Li 2 O slab measured at FNS in JAERI, tritium production rate (TPR) in the graphite-reflected Li 2 O sphere measured at FNS and the TPR in the metallic Li sphere measured at KfK. In addition in order to test an accuracy of the calculation method in detail, spectra of neutrons scattered from a small sample and various reaction rates in a Li 2 O cylinder were compared between the present method and the continuous energy Monte Carlo method. The nuclear data files used are mainly ENDF/B4 and partly JENDL-3PR1. The tests were carried out through a comparison with the measured values and also with the results obtained from the conventional Legendre expansion method and the continuous energy Monte Carlo method. It is found that the results by the present method are more accurate than those by the conventional one and agree well with those by the continuous energy Monte Carlo calculations. Discrepancies due to the nuclear data are also discussed. (author)

A compilation of nuclear weapons test detonation data for U.S. Pacific ocean tests.

Science.gov (United States)

Simon, S L; Robison, W L

1997-07-01

Prior to December 1993, the explosive yields of 44 of 66 nuclear tests conducted by the United States in the Marshall Islands were still classified. Following a request from the Government of the Republic of the Marshall Islands to the U.S. Department of Energy to release this information, the Secretary of Energy declassified and released to the public the explosive yields of the Pacific nuclear tests. This paper presents a synopsis of information on nuclear test detonations in the Marshall Islands and other locations in the mid-Pacific including dates, explosive yields, locations, weapon placement, and summary statistics.

The 20th nuclear explosion test of the Peoples' Republic of China (underground nuclear test)

International Nuclear Information System (INIS)

Anon.

1977-01-01

(1) The New China News Agency and the Radio Peking announced that China conducted the underground nuclear explosion test on 17 October, 1976. However, no exact data concerning the data, the place and the scale of this test was stated in above announcement. (2) However, relatively high radioactivity than that of normal level was detected in the rain and dry fallout samples collected from several prefectures. (author)

On-site tests on the nuclear power plants

International Nuclear Information System (INIS)

Morilhat, P.; Favennec, J.M.; Neau, P.; Preudhomme, E.

1996-01-01

On-site tests and experiments are performed by EDF Research and Development Division on the nuclear power plants to assess the behaviour of major components submitted to thermal and vibratory solicitations. On-going studies deal with the qualification of new nuclear power plant standard and with the feedback of plants under operation. The tests, particularly the investigation tests, correspond to large investments and entail an important data volume which must ensure the continuity over a long period of the order of magnitude of the in-service plant life (around 40 years). This paper addresses the on-site experimental activities, describes the means to be used, and gives an example: the qualification of SG of new 1450 MW nuclear power plants. (author)

Nuclear Analyses of Indian LLCB Test Blanket System in ITER

Science.gov (United States)

Swami, H. L.; Shaw, A. K.; Danani, C.; Chaudhuri, Paritosh

2017-04-01

Heading towards the Nuclear Fusion Reactor Program, India is developing Lead Lithium Ceramic Breeder (LLCB) tritium breeding blanket for its future fusion Reactor. A mock-up of the LLCB blanket is proposed to be tested in ITER equatorial port no.2, to ensure the overall performance of blanket in reactor relevant nuclear fusion environment. Nuclear analyses play an important role in LLCB Test Blanket System design & development. It is required for tritium breeding estimation, thermal-hydraulic design, coolants process design, radioactive waste management, equipment maintenance & replacement strategies and nuclear safety. The nuclear behaviour of LLCB test blanket module in ITER is predicated in terms of nuclear responses such as tritium production, nuclear heating, neutron fluxes and radiation damages. Radiation shielding capability of LLCB TBS inside and outside bio-shield was also assessed to fulfill ITER shielding requirements. In order to supports the rad-waste and safety assessment, nuclear activation analyses were carried out and radioactivity data were generated for LLCB TBS components. Nuclear analyses of LLCB TBS are performed using ITER recommended nuclear analyses codes (i.e. MCNP, EASY), nuclear cross section data libraries (i.e. FENDL 2.1, EAF) and neutronic model (ITER C-lite v.l). The paper describes a comprehensive nuclear performance of LLCB TBS in ITER.

Nuclear Materials Management for the Nevada Test Site (NTS)

International Nuclear Information System (INIS)

Jesse C. Schreiber

2007-01-01

The Nevada Test Site (NTS) has transitioned from its historical role of weapons testing to a broader role that is focused on being a solution to multiple National Nuclear Security Administration (NNSA) challenges and opportunities with nuclear materials for the nation. NTS is supporting other NNSA sites challenged with safe nuclear materials storage and disposition. NNSA, with site involvement, is currently transforming the nuclear stockpile and supporting infrastructure to meet the 2030 vision. Efforts are under way to make the production complex smaller, more consolidated, and more modern. With respect to the nuclear material stockpile, the NNSA sites are currently reducing the complex nuclear material inventory through dispositioning and consolidating nuclear material. This includes moving material from other sites to NTS. State-of-the-art nuclear material management and control practices at NTS are essential for NTS to ensure that these new activities are accomplished in a safe, secure, efficient, and environmentally responsible manner. NTS is aggressively addressing this challenge

Secondary Waste Cast Stone Waste Form Qualification Testing Plan

Energy Technology Data Exchange (ETDEWEB)

Westsik, Joseph H.; Serne, R. Jeffrey

2012-09-26

The Hanford Tank Waste Treatment and Immobilization Plant (WTP) is being constructed to treat the 56 million gallons of radioactive waste stored in 177 underground tanks at the Hanford Site. The WTP includes a pretreatment facility to separate the wastes into high-level waste (HLW) and low-activity waste (LAW) fractions for vitrification and disposal. The LAW will be converted to glass for final disposal at the Integrated Disposal Facility (IDF). Cast Stone – a cementitious waste form, has been selected for solidification of this secondary waste stream after treatment in the ETF. The secondary-waste Cast Stone waste form must be acceptable for disposal in the IDF. This secondary waste Cast Stone waste form qualification testing plan outlines the testing of the waste form and immobilization process to demonstrate that the Cast Stone waste form can comply with the disposal requirements. Specifications for the secondary-waste Cast Stone waste form have not been established. For this testing plan, Cast Stone specifications are derived from specifications for the immobilized LAW glass in the WTP contract, the waste acceptance criteria for the IDF, and the waste acceptance criteria in the IDF Permit issued by the State of Washington. This testing plan outlines the testing needed to demonstrate that the waste form can comply with these waste form specifications and acceptance criteria. The testing program must also demonstrate that the immobilization process can be controlled to consistently provide an acceptable waste form product. This testing plan also outlines the testing needed to provide the technical basis for understanding the long-term performance of the waste form in the disposal environment. These waste form performance data are needed to support performance assessment analyses of the long-term environmental impact of the secondary-waste Cast Stone waste form in the IDF

Nur77 forms novel nuclear structures upon DNA damage that cause transcriptional arrest

International Nuclear Information System (INIS)

Leseleuc, Louis de; Denis, Francois

2006-01-01

The orphan nuclear receptor Nur77 has been implicated in both growth and apoptosis, and its function and activity can be modulated by cellular redistribution. Green fluorescent protein-tagged Nur77 was used to evaluate the role of Nur77 intracellular redistribution in response to genotoxic stress. Selected DNA damaging agents and transcription inhibition lead to rapid redistribution of Nur77 into nuclear structures distinct from conventional nuclear bodies. These nuclear bodies formed transiently were tightly bound to the nuclear matrix and conditions that lead to their appearance were associated with Nur77 transcriptional inhibition. The formation of Nur77 nuclear bodies might be involved in programmed cell death modulation upon exposure to DNA damaging agents that inhibit transcription by sequestrating this proapoptotic factor in dense nuclear structures

Overview of mineral waste form development for the electrometallurgical treatment of spent nuclear fuel

International Nuclear Information System (INIS)

Pereira, C.; Lewis, M.A.; Ackerman, J.P.

1996-01-01

Argonne is developing a method to treat spent nuclear fuel in a molten salt electrorefiner. Wastes from this treatment will be converted into metal and mineral forms for geologic disposal. A glass-bonded zeolite is being developed to serve as the mineral waste form that will contain the fission products that accumulate in the electrorefiner salt. Fission products are ion exchanged from the salt into the zeolite A structure. The crystal structure of the zeolite after ion exchange is filled with salt ions. The salt-loaded zeolite A is mixed with glass frit and hot pressed. During hot pressing, the zeolite A may be converted to sodalite which also retains the waste salt. The glass-bonded zeolite is leach resistant. MCC-1 testing has shown that it has a release rate below 1 g/(m 2 day) for all elements

Yesterday's, today's and tomorrow's nuclear tests of India and Pakistan

International Nuclear Information System (INIS)

Duval, M.; Le Guelte, G.

1998-01-01

This paper presents the historical aspects that led India and Pakistan to develop nuclear weapons and to perform nuclear weapon tests: weapons acquisition: today's military capacity, help from foreign countries; motivations: nuclear programs, geo-political aspects; results and potentialities; consequences for the non-proliferation systems and for the cut-off convention and test-ban treaties; and the geo-strategic consequences of todays's military nuclear capacity of India and Pakistan. (J.S.)

Techniques to eliminate nuclear weapons testing infrastructure at former Semipalatinsk test site

International Nuclear Information System (INIS)

Erofeev, I.E.; Kovalev, V.V.

2003-01-01

It was at the former Semipalatinsk Test Site where for the first time in the world the nuclear weapons testing infrastructure elimination was put into practice. Fundamentally new procedures for blasting operations have been developed by specialists of the Kazakh State Research and Production Center of Blasting Operations (KSCBO), National Nuclear Center of the Republic of Kazakhstan (NNC) and Degelen Enterprise to enhance reliability and provide safety during elimination of various objects and performance of large-scale experiments. (author)

Nuclear explosives testing readiness evaluation

Energy Technology Data Exchange (ETDEWEB)

Valk, T.C.

1993-09-01

This readiness evaluation considers hole selection and characterization, verification, containment issues, nuclear explosive safety studies, test authorities, event operations planning, canister-rack preparation, site preparation, diagnostic equipment setup, device assembly facilities and processes, device delivery and insertion, emplacement, stemming, control room activities, readiness briefing, arming and firing, test execution, emergency response and reentry, and post event analysis to include device diagnostics, nuclear chemistry, and containment. This survey concludes that the LLNL program and its supporting contractors could execute an event within six months of notification, and a second event within the following six months, given the NET group`s evaluation and the following three restraints: (1) FY94 (and subsequent year) funding is essentially constant with FY93, (2) Preliminary work for the initial event is completed to the historical sic months status, (3) Critical personnel, currently working in dual use technologies, would be recallable as needed.

Improved polyphase ceramic form for high-level defense nuclear waste

International Nuclear Information System (INIS)

Harker, A.B.; Morgan, P.E.D.; Clarke, D.R.; Flintoff, J.J.; Shaw, T.M.

1983-01-01

An improved ceramic nuclear waste form and fabrication process have been developed using simulated Savannah River Plant defense high-level waste compositions. The waste form provides flexibility with respect to processing conditions while exhibiting superior resistance to ground water leaching than other currently proposed forms. The ceramic, consolidated by hot-isostatic pressing at 1040 0 C and 10,000 psi, is composed of six major phases, nepheline, zirconolite, a murataite-type cubic phase, magnetite-type spinel, a magnetoplumbite solid solution, and perovskite. The waste form provides multiple crystal lattice sites for the waste elements, minimizes amorphous intergranular material, and can accommodate waste loadings in excess of 60 wt %. The fabrication of the ceramic can be accomplished with existing manufacturing technology and eliminates the effects of radionuclide volatilization and off-gas induced corrosion experienced with the molten processes for vitreous form production

Thermohydraulic tests in nuclear fuel model

International Nuclear Information System (INIS)

Ladeira, L.C.D.; Navarro, M.A.

1984-01-01

The main experimental works performed in the Thermohydraulics Laboratory of the NUCLEBRAS Nuclear Technology Development Center, in the field of thermofluodynamics are briefly described. These works include the performing of steady-state flow tests in single tube test sections, and the design and construction of a rod bundle test section, which will be also used for those kind of testes. Mention is made of the works to be performed in the near future, related to steady-state and transient flow tests. (Author) [pt

Testing waste forms containing high radionuclide loadings

International Nuclear Information System (INIS)

McConnell, J.W. Jr.; Neilson, R.M. Jr.; Rogers, R.D.

1986-01-01

The Low-Level Waste Data Base Development - EPICOR-II Resin/Liner Investigation Program of the US Nuclear Regulatory Commission (NRC) is obtaining information on radioactive waste during NRC-prescribed tests and in a disposal environment. This paper describes the resin solidification task of that program, including the present status and results to date

Out-pile Test of Double Cladding Fuel Rod Mockups for a Nuclear Fuel Irradiation Test

Energy Technology Data Exchange (ETDEWEB)

Sohn, Jaemin; Park, Sungjae; Kang, Younghwan; Kim, Harkrho; Kim, Bonggoo; Kim, Youngki [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

2008-05-15

An instrumented capsule for a nuclear fuel irradiation test has been developed to measure fuel characteristics, such as a fuel temperature, internal pressure of a fuel rod, a fuel pellet elongation and a neutron flux during an irradiation test at HANARO. In the future, nuclear fuel irradiation tests under a high temperature condition are expected from users. To prepare for this request, we have continued developing the technology for a high temperature nuclear fuel irradiation test at HANARO. The purpose of this paper is to verify the possibility that the temperature of a nuclear fuel can be controlled at a high temperature during an irradiation test. Therefore we designed and fabricated double cladding fuel rod mockups. And we performed out-pile tests using these mockups. The purposes of a out-pile test is to analyze an effect of a gap size, which is between an outer cladding and an inner cladding, on the temperature and the effect of a mixture ratio of helium gas and neon gas on the temperature. This paper presents the design and fabrication of double cladding fuel rod mockups and the results of the out-pile test.

The new technologies and infrastructure conversion of nuclear testing in Kazakhstan

International Nuclear Information System (INIS)

Kadyrzhanov, K.K.

1999-01-01

It is known, that in August, 1991, in accordance with Decree by the Kazakhstan President, the Semipalatinsk test site (STS) was shut down, and practical works on its conversion were initiated. In 1991 the decision on creation of the Kazakhstan National Nuclear Center (KNNC) on a base of the test site scientific and industrial enterprises and Inst. of Nuclear Physics was taken. In 1993 within frame KNNC three new institutes (Inst. of Atomic Energy, Inst. of Geophysical Research, Inst. of Radiation Safety and Ecology) were created. Owing to this, at the condition of USSR disintegration and liquidation of military division in test site territory, high-qualified personnel was saved, the facilities that represent nuclear danger were left under operation and surveillance, and the full-scale program of STS conversion was developed and put into life. At present guidelines for the major research activities at KNNC on conversion program are as follows: liquidation of consequences of nuclear tests; liquidation of technological structure used before for preparation and implementation of nuclear weapons tests; creation of technology, equipment and locations for receipt and storage of radioactive wastes; working out the concept of nuclear power development in Kazakhstan; investigation of the behaviour of melted reactor core in view of potential heavy accidents at nuclear power plants; development of technique and means for detection of nuclear test in the world, continuous control for nuclear explosions; experimental works on investigation of behaviour of the materials-candidates for role of constructional materials for the thermonuclear reactor ITER; creation of high-technology industries. These and other activities undertaken in this respect allow to attract considerable foreign investments, to create in Kurchatov city hundreds of additional working places.The Government support rendered to KNNC in future will allow to expand substantially this area of activities as well as to

Secondary phases formed during nuclear waste glass-water interactions: Thermodynamic and derived properties

International Nuclear Information System (INIS)

McKenzie, W.F.

1992-08-01

The thermodynamic properties of secondary phases observed to form during nuclear waste glass-water interactions are of particular interest as it is with the application of these properties together with the thermodynamic properties of other solid phases, fluid phases, and aqueous species that one may predict the environmental consequences of introducing radionuclides contained in the glass into groundwater at a high-level nuclear waste repository. The validation of these predicted consequences can be obtained from laboratory experiments and field observations at natural analogue sites. The purpose of this report is to update and expand the previous compilation (McKenzie, 1991) of thermodynamic data retrieved from the literature and/or estimated for secondary phases observed to form (and candidate phases from observed chemical compositions) during nuclear waste glass-water interactions. In addition, this report includes provisionally recommended thermodynamic data of secondary phases

Analysis of North Korea's Nuclear Tests under Prospect Theory

Energy Technology Data Exchange (ETDEWEB)

Lee, Han Myung; Ryu, Jae Soo; Lee, Kwang Seok; Lee, Dong Hoon; Jun, Eunju; Kim, Mi Jin [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

2013-10-15

North Korea has chosen nuclear weapons as the means to protect its sovereignty. Despite international society's endeavors and sanctions to encourage North Korea to abandon its nuclear ambition, North Korea has repeatedly conducted nuclear testing. In this paper, the reason for North Korea's addiction to a nuclear arsenal is addressed within the framework of cognitive psychology. The prospect theory addresses an epistemological approach usually overlooked in rational choice theories. It provides useful implications why North Korea, being under a crisis situation has thrown out a stable choice but taken on a risky one such as nuclear testing. Under the viewpoint of prospect theory, nuclear tests by North Korea can be understood as follows: The first nuclear test in 2006 is seen as a trial to escape from loss areas such as financial sanctions and regime threats; the second test in 2009 was interpreted as a consequence of the strategy to recover losses by making a direct confrontation against the United States; and the third test in 2013 was understood as an attempt to strengthen internal solidarity after Kim Jong-eun inherited the dynasty, as well as to enhance bargaining power against the United States. Thus, it can be summarized that Pyongyang repeated its nuclear tests to escape from a negative domain and to settle into a positive one. In addition, in the future, North Korea may not be willing to readily give up its nuclear capabilities to ensure the survival of its own regime.

Coupling of Nuclear Waste Form Corrosion and Radionuclide Transports in Presence of Relevant Repository Sediments

International Nuclear Information System (INIS)

Wall, Nathalie A.; Neeway, James J.; Qafoku, Nikolla P.; Ryan, Joseph V.

2015-01-01

Assessments of waste form and disposal options start with the degradation of the waste forms and consequent mobilization of radionuclides. Long-term static tests, single-pass flow-through tests, and the pressurized unsaturated flow test are often employed to study the durability of potential waste forms and to help create models that predict their durability throughout the lifespan of the disposal site. These tests involve the corrosion of the material in the presence of various leachants, with different experimental designs yielding desired information about the behavior of the material. Though these tests have proved instrumental in elucidating various mechanisms responsible for material corrosion, the chemical environment to which the material is subject is often not representative of a potential radioactive waste repository where factors such as pH and leachant composition will be controlled by the near-field environment. Near-field materials include, but are not limited to, the original engineered barriers, their resulting corrosion products, backfill materials, and the natural host rock. For an accurate performance assessment of a nuclear waste repository, realistic waste corrosion experimental data ought to be modeled to allow for a better understanding of waste form corrosion mechanisms and the effect of immediate geochemical environment on these mechanisms. Additionally, the migration of radionuclides in the resulting chemical environment during and after waste form corrosion must be quantified and mechanisms responsible for migrations understood. The goal of this research was to understand the mechanisms responsible for waste form corrosion in the presence of relevant repository sediments to allow for accurate radionuclide migration quantifications. The rationale for this work is that a better understanding of waste form corrosion in relevant systems will enable increased reliance on waste form performance in repository environments and potentially

Coupling of Nuclear Waste Form Corrosion and Radionuclide Transports in Presence of Relevant Repository Sediments

Energy Technology Data Exchange (ETDEWEB)

Wall, Nathalie A. [Washington State Univ., Pullman, WA (United States); Neeway, James J. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Qafoku, Nikolla P. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Ryan, Joseph V. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States)

2015-09-30

Assessments of waste form and disposal options start with the degradation of the waste forms and consequent mobilization of radionuclides. Long-term static tests, single-pass flow-through tests, and the pressurized unsaturated flow test are often employed to study the durability of potential waste forms and to help create models that predict their durability throughout the lifespan of the disposal site. These tests involve the corrosion of the material in the presence of various leachants, with different experimental designs yielding desired information about the behavior of the material. Though these tests have proved instrumental in elucidating various mechanisms responsible for material corrosion, the chemical environment to which the material is subject is often not representative of a potential radioactive waste repository where factors such as pH and leachant composition will be controlled by the near-field environment. Near-field materials include, but are not limited to, the original engineered barriers, their resulting corrosion products, backfill materials, and the natural host rock. For an accurate performance assessment of a nuclear waste repository, realistic waste corrosion experimental data ought to be modeled to allow for a better understanding of waste form corrosion mechanisms and the effect of immediate geochemical environment on these mechanisms. Additionally, the migration of radionuclides in the resulting chemical environment during and after waste form corrosion must be quantified and mechanisms responsible for migrations understood. The goal of this research was to understand the mechanisms responsible for waste form corrosion in the presence of relevant repository sediments to allow for accurate radionuclide migration quantifications. The rationale for this work is that a better understanding of waste form corrosion in relevant systems will enable increased reliance on waste form performance in repository environments and potentially

Radioactive fallout in the southern hemisphere from nuclear weapons tests

International Nuclear Information System (INIS)

Moroney, J.R.

1979-11-01

Fallout in the southern hemisphere, and its origins in the national programs of atmospheric nuclear weapons testing in both hemispheres, are reviewed. Of the 390 nuclear tests conducted in the atmosphere to date, 53 were carried out in the southern hemisphere and it is the second phase of these, between 1966 and 1974, that is seen to have been responsible for the main fallout of short-lived fission products in the southern hemisphere. In contrast to this, the programs of atmospheric nuclear testing in the northern hemisphere up to 1962 are shown to have been the main source of long-lived fission products in fallout in the southern hemisphere. The course followed by this contamination through the environment of the southern hemisphere is traced for the national programs of nuclear testing after 1962 taken separately (France, China) and for the earlier national programs taken together (U.S.S.R., U.S.A. and U.K.). The impact on populations in the southern hemisphere of fallout from atmospheric nuclear weapons tests to date is assessed

DPRK's 4"t"h Nuclear Test and its Tritium Production

International Nuclear Information System (INIS)

Kim, Min Soo; Lee, Sang Joon; Chang, Sun Young

2016-01-01

On January 6, 2016 at 10:30am, the artificial earthquake in the DPRK was detected by multiple international seismic organizations. After 2 hours, the DPRK announced on state TV that 'The first H-bomb test was successfully conducted in the DPRK at 10:00 am on Wednesday, Juche 105(2016), pursuant to the strategic determination of the ruling communist party.' There has been a doubt about the real nature of the DPRK's 4th nuclear test, since 2 months have been passed after its nuclear test. To analyze the nature of the DPRK's nuclear test, it is necessary to check possible options for production of essential materials. The pathways to produce nuclear fusion material (tritium) and to have a relatively high possibility for the DPRK are described in this article. Tritium is key material for H-bomb. And there are two options for the DPRK which are 1) production and 2) illicit trafficking. And this study is focused on production possibility of DPRK. Determination of the nature of DPRK's nuclear test is very hard issue

Radioactive fallout in the southern hemisphere from nuclear weapons tests

International Nuclear Information System (INIS)

Moroney, J.R.

1979-01-01

Fallout in the southern hemisphere, and its origins in the national programs of atmospheric nuclear weapons testing in both hemispheres, are reviewed. Of the 390 nuclear tests conducted in the atmosphere to date, 53 were carried out in the southern hemisphere and it is the second phase of these, between 1966 and 1974, that is seen to have been responsible for the main fallout of short-lived fission products in the southern hemisphere. In contrast to this, the programs of atmospheric nuclear testing in the northern hemisphere up to 1962 are shown to have been the main source of long-lived fission products in fallout in the southern hemisphere. The course followed by this contamination through the environment of the southern hemisphere is traced for the national programs of nuclear testing after 1962 taken separately (France, China) and for the earlier national programs taken together (U.S.S.R., U.S.A. and U.K.). The impact on populations in the southern hemisphere of fallout from atmospheric nuclear weapons tests to date is assessed. (author)

Nuclear test at Semipalatinsk test site and their environmental impacts

International Nuclear Information System (INIS)

Logachev, V.A.

2000-01-01

This paper present classification of nuclear tests conducted at the Semipalatinsk test site by tier radiation hazards. The Institute of Biophysics of the Russian Ministry of Health established a data base the archival data on radiation situation parameters and compiled an album of radioactive plum footprints. The paper states that external and internal exposure doses received by population lived in the test vicinity can sufficiently reliably assesses using archival data. (author)

On-site inspection: A brief overview and bibliography of techniques pertinent to assessing suspected nuclear test sites

International Nuclear Information System (INIS)

Carrigan, C.R.

1993-03-01

The purpose of this report is to provide a brief overview and bibliography of those techniques that may have application for the evaluation of a site to determine if a high energy release event is nuclear in nature. This effort is motivated by recognition of the changing world political climate and the perception that low yield and non-proliferation issues will grow in importance as countries become increasingly involved as signators to treaties that are intended to limit the development and testing of nuclear weapons. Along with an increasing interest in such issues is the awareness of the need to implement improved capabilities for treaty monitoring programs that must deal with assessing suspicious occurrences of high energy release events. In preparing this report, it is recognized that monitoring can take two main forms. The first involves the resolution of unidentified events detected by seismic and satellite National Technical Means. Events of an indeterminate nature could occur world-wide and could induce tension in neighboring countries. If an on-site measurement capability were available, a monitoring team could be sent to the suspected site of an event to take measurements that could confirm or disprove the occurrence of a clandestine nuclear test. The second monitoring form is the confirmation that a clandestine event is not masked by a declared event. For example, a large mining explosion could mask a decoupled nuclear explosion. On-site measurements before and during the test could confirm that a clandestine event did not occur and could provide assurance that the party carrying out the explosion is not taking advantage of clandestine testing opportunities. 48 refs

Semipalatinsk nuclear test site: History of building and function

International Nuclear Information System (INIS)

Sergazina, G.M.; Balmukhanov, S.B.

1999-01-01

A vast materials on history of Semipalatinsk nuclear test site creation and it building and function are presented. Authors with big reliability report one page of Kazakhstan's history. In steppe on naked place thousands of soldiers and officers, construct and military specialists have built the nuclear site on which during 40 years were conducting nuclear tests . Prolonged chronic radiation on population living near by site results to tragedy which is confessed by General Assembly of United Nations. In the book aspects of test site conversion and rehabilitation of injured population are considered. The book consists of introduction, three chapters and conclusion. The book is intended to wide circle of readers. (author)

Leaching of nuclear power reactor waste forms

International Nuclear Information System (INIS)

Endo, L.S.; Villalobos, J.P.; Miyamoto, H.

1987-01-01

The leaching tests for immobilized power reactor wastes carried out at IPEN are described. These wastes forms consist mainly of spent resins and boric acid concentrates solidified in ordinary Portland cement. All tests were conducted according to the ISO and IAEA recommendations. Three years leaching results are reported. The cesium diffuvity coefficients determined out of these results are about 1 x 10 -8 cm 2 /s for boric acid waste form and 9 x 10 -9 cm 2 /s for ion-exchange resin waste. Strontium diffusivity coefficients found are about 3 x 10 -11 cm 2 /s and 9 x 10 -11 cm 2 /s respectively. (Author) [pt

Environmental assessment report: Nuclear Test Technology Complex

International Nuclear Information System (INIS)

Tonnessen, K.; Tewes, H.A.

1982-08-01

The US Department of Energy (USDOE) is planning to construct and operate a structure, designated the Nuclear Test Technology Complex (NTTC), on a site located west of and adjacent to the Lawrence Livermore National Laboratory. The NTTC is designed to house 350 nuclear test program personnel, and will accommodate the needs of the entire staff of the continuing Nuclear Test Program (NTP). The project has three phases: land acquisition, facility construction and facility operation. The purpose of this environmental assessment report is to describe the activities associated with the three phases of the NTTC project and to evaluate potential environmental disruptions. The project site is located in a rural area of southeastern Alameda County, California, where the primary land use is agriculture; however, the County has zoned the area for industrial development. The environmental impacts of the project include surface disturbance, high noise levels, possible increases in site erosion, and decreased air quality. These impacts will occur primarily during the construction phase of the NTTC project and can be mitigated in part by measures proposed in this report

Approved reference and testing materials for use in Nuclear Waste Management Research and Development Programs

International Nuclear Information System (INIS)

Mellinger, G.B.; Daniel, J.L.

1984-12-01

This document, addressed to members of the waste management research and development community summarizes reference and testing materials available from the Nuclear Waste Materials Characterization Center (MCC). These materials are furnished under the MCC's charter to distribute reference materials essential for quantitative evaluation of nuclear waste package materials under development in the US. Reference materials with known behavior in various standard waste management related tests are needed to ensure that individual testing programs are correctly performing those tests. Approved testing materials are provided to assist the projects in assembling materials data base of defensible accuracy and precision. This is the second issue of this publication. Eight new Approved Testing Materials are listed, and Spent Fuel is included as a separate section of Standard Materials because of its increasing importance as a potential repository storage form. A summary of current characterization information is provided for each material listed. Future issues will provide updates of the characterization status of the materials presented in this issue, and information about new standard materials as they are acquired. 7 references, 1 figure, 19 tables

Recent irradiation tests for future nuclear system at HANARO

Energy Technology Data Exchange (ETDEWEB)

Cho, Man Soon; Choo, Kee Nam; Yang, Seong Woo; Park, Sang Jun [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

2016-05-15

The capsule at HANARO is a device that evaluates the irradiation effects of nuclear materials and fuels, which can reproduce the environment of nuclear power plants and accelerate to reach to the end of life condition. As the integrity assessment and the extension of lifetime of nuclear power plants are recently considered as important issues in Korea, the requirements for irradiation test are gradually being increased. The capacity and capability irradiation tests at HANARO are becoming important because Korea strives to develop SFR (Sodium-cooled Fast Reactor) and VHTR (Very High Temperature Reactor) among the future nuclear system and to export the research reactors and to develop the fusion reactor technology.

Nuclear test-experimental science annual report, Fiscal year 1990

International Nuclear Information System (INIS)

Struble, G.L.; Middleton, C.; Anderson, S.E.; Cherniak, J.; Donohue, M.L.; Francke, A.; Hedman, I.; Kirvel, R.D.

1991-01-01

Fiscal year 1990 was another year of outstanding accomplishments for the Nuclear Test-Experimental Science (NTES) Program at Lawrence Livermore National Laboratory (LLNL). We continued to make progress to enhance the experimental science in the Weapons Program and to improve the operational efficiency and productivity of the Nuclear Test Program

Guarantying and testing the nuclear safeguards

International Nuclear Information System (INIS)

Turcu, Ilie

2002-01-01

Apparently, the nuclear power will ensure an important share of the world energy demand at least for the next decades because there is no viable alternative in the fan of energy sources neither one complying with the environment preservation requirements. The nuclear energy future depends not only on technical and economical aspects but also on preventing any danger of nuclear safeguards nature. The main international legal instrument which provides concrete commitments for nations in this field is the Nuclear Safeguard Convention. It provides guarantees and testings of the nuclear safeguards over the entire service life of the nuclear power plants. In the two general conferences (of 1999 and 2002) the status and measures adopted in the field of nuclear safeguards by the states adhering to the convention were discussed and reviewed, as well as the issues of financial resources, licensing and the adequate measures in emergency cases. The nuclear safeguards is a major issue among the criteria of integration in UE. Essential for maintaining and endorsing the provisions of nuclear safeguards in Romania are specific research and development activities aiming at integrating the equipment and structures, solving the operation problems of nuclear facilities, studying the behavior of installations in transient regimes, investigating the reliability and probabilistic assessing of nuclear safeguards, examining the phenomenology and simulating severe accidents or human factor behavior. Of major importance appears to be the international cooperation aiming that a permanent exchange of information and experience, dissemination of the best results, solutions and practices. The paper presents the status and trends at the world level, as well as in Romania, underlining the main issues of the strategy in this field and stressing the financial and human resources implied the implementing the nuclear safeguards provisions

Traditional nuclear physics as a test of nuclear exotics

International Nuclear Information System (INIS)

Sapershtein, E.E.; Starodubskii, V.E.

1989-01-01

The review considers the testing of some exotic hypotheses about the properties of the nucleon in a nuclear medium in phenomena of traditional nuclear physics. The hypothesis of nucleon swelling proposed to explain the EMC effects is considered in detail. The consequences of this hypothesis for the charge densities and cross sections for scattering of fast electrons and protons by nuclei are analyzed. Also considered are the Nolen--Schiffer anomaly, the Coulomb sum rule for inelastic electron scattering, y scaling, and some other nuclear processes. It is shown that one can estimate the possible scale of nuclear exotics by analyzing many of these phenomena. Thus, examination of high-precision data on the elastic scattering of electrons with energy 500--700 MeV using density distributions calculated on the basis of the self-consistent theory of finite Fermi systems yields a restriction on the amount of nucleon swelling: α=δr N /r N approx-lt 10%. A similar analysis for protons with energy 0.8--1.0 GeV using Glauber theory gives α approx-lt 6%. An even more stringent restriction, α approx-lt 3%, follows from data on y scaling in 56 Fe

Results of EPR dosimetry for population in the vicinity of the most contaminating radioactive fallout trace after the first nuclear test in the Semipalatinsk test site

International Nuclear Information System (INIS)

Ivannikov, Alexander; Zhumadilov, Kassym; Tieliewuhan, Eldana

2006-01-01

The method of electron paramagnetic resonance (EPR) spectroscopy for tooth enamel is applied to individual radiation dose determination to residents of two villages (Dolon and Mostik) in the vicinity of the Semipalatinsk nuclear test site in Kazakhstan. These villages are located near the central axis of the radioactive fallout trace of the most contaminating surface nuclear test conducted in 1949. It is found that excess doses obtained by subtraction of natural background dose from dose absorbed in enamel range up to 440 mGy to residents of Dolon, whose enamel was formed before 1949, and do not exceed 120 mGy to younger residents. To residents of Mostik, excess doses do not exceed 100 mGy regardless of age except for one resident with an extremely high dose of 1.25 Gy. These results are in agreement with the pattern of radioactive contamination of the territory after the nuclear test of 1949 except one case of extremely high dose, which should be additionally investigated. (author)

Stabilities of nuclear waste forms and their geochemical interactions in repositories

International Nuclear Information System (INIS)

White, W.B.

1980-01-01

The stabilities of high-level nuclear waste forms in a repository environment are briefly discussed. The advantages and disadvantages of such waste forms as borosilicate glass, supercalcine ceramics, and synthetic minerals are presented in context with the different rock types which have been proposed as possible host rocks for repositories. It is concluded that the growing geochemical evidence favors the use of a silicate rock repository because of the effectiveness of aluminosilicate rocks as chemical barriers for most radionuclides

Testing lifting systems in nuclear facilities

International Nuclear Information System (INIS)

Kling, H.; Laug, R.

1984-01-01

Lifting systems in nuclear facilities must be inspected at regular intervals after having undergone their first acceptance test. These inspections are frequently carried out by service firms which not only employ the skilled personnel required for such jobs but also make available the necessary test equipment. The inspections in particular include a number of sophisticated load tests for which test load systems have been developed to allow lifting systems to be tested so that reactor specific boundary conditions are taken into account. In view of the large number of facilities to be inspected, the test load system is a modular system. (orig.) [de

Sturdy on Orbital TIG Welding Properties for Nuclear Fuel Test Rod

International Nuclear Information System (INIS)

Joung, Changyoung; Hong, Jintae; Kim, Kahye; Huh, Sungho

2014-01-01

We developed a precision TIG welding system that is able to weld the seam between end-caps and a fuel cladding tube for the nuclear fuel test rod and rig. This system can be mainly classified into an orbital TIG welder (AMI, M-207A) and a pressure chamber. The orbital TIG welder can be independently used, and it consists of a power supply unit, a microprocessor, water cooling unit, a gas supply unit and an orbital weld head. In this welder, the power supply unit mainly supplies GTAW power for a welding specimen and controls an arc starting of high frequency, supping of purge gas, arc rotation through the orbital TIG welding head, and automatic timing functions. In addition, the pressure chamber is used to make the welded surface of the cladding specimen clean with the inert gas filled inside the chamber. To precisely weld the cladding tube, a welding process needs to establish a schedule program for an orbital TIG welding. Therefore, the weld tests were performed on a cladding tube and dummy rods under various conditions. This paper describes not only test results on parameters of the purge gas flow rates and the chamber gas pressures for the orbital TIG welding, but also test results on the program establishment of an orbital TIG welding system to weld the fuel test rods. Various welding tests were performed to develop the orbital TIG welding techniques for the nuclear fuel test rod. The width of HAZ of a cladding specimen welded with the identical power during an orbital TIG welding cycle was continuously increased from a welded start-point to a weld end-point because of heat accumulation. The welding effect of the PGFR and CGP shows a relatively large difference for FSS and LSS. Each hole on the cladding specimens was formed in the 1bar CGP with the 20L/min PGFR but not made in the case of the PGFR of 10L/min in the CGP of 2bar. The optimum schedule program of the orbital TIG welding system to weld the nuclear fuel test rod was established through the program

Sturdy on Orbital TIG Welding Properties for Nuclear Fuel Test Rod

Energy Technology Data Exchange (ETDEWEB)

Joung, Changyoung; Hong, Jintae; Kim, Kahye; Huh, Sungho [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

2014-05-15

We developed a precision TIG welding system that is able to weld the seam between end-caps and a fuel cladding tube for the nuclear fuel test rod and rig. This system can be mainly classified into an orbital TIG welder (AMI, M-207A) and a pressure chamber. The orbital TIG welder can be independently used, and it consists of a power supply unit, a microprocessor, water cooling unit, a gas supply unit and an orbital weld head. In this welder, the power supply unit mainly supplies GTAW power for a welding specimen and controls an arc starting of high frequency, supping of purge gas, arc rotation through the orbital TIG welding head, and automatic timing functions. In addition, the pressure chamber is used to make the welded surface of the cladding specimen clean with the inert gas filled inside the chamber. To precisely weld the cladding tube, a welding process needs to establish a schedule program for an orbital TIG welding. Therefore, the weld tests were performed on a cladding tube and dummy rods under various conditions. This paper describes not only test results on parameters of the purge gas flow rates and the chamber gas pressures for the orbital TIG welding, but also test results on the program establishment of an orbital TIG welding system to weld the fuel test rods. Various welding tests were performed to develop the orbital TIG welding techniques for the nuclear fuel test rod. The width of HAZ of a cladding specimen welded with the identical power during an orbital TIG welding cycle was continuously increased from a welded start-point to a weld end-point because of heat accumulation. The welding effect of the PGFR and CGP shows a relatively large difference for FSS and LSS. Each hole on the cladding specimens was formed in the 1bar CGP with the 20L/min PGFR but not made in the case of the PGFR of 10L/min in the CGP of 2bar. The optimum schedule program of the orbital TIG welding system to weld the nuclear fuel test rod was established through the program

International Symposium of Scientists for Nuclear test Stopping

International Nuclear Information System (INIS)

Anon.

1986-01-01

Problems discussed at International Symposium of Scientists for Nuclear Test Stopping in July 1986 in Moscow were considered. Scientists discussed complex of possible measures directed at strengthening of peace supporting mechanism, spoke in support of prohibition of all nuclear weapon tests. Necessity of measures preventing the weapon delivery to space, construction of the regime of using cosmic equipment exclusively for peace was noted. Attention was paid to the problem of control for test stopping (by means of sattelites and seismic methods), cooperation establishment between the USSR Academy of Sciences and the Council for the protection of the USA Natural Resources

Nuclear-physical methods in macro- and microanalytical investigations of contamination with radionuclides at Semipalatinsk Nuclear Test Site

International Nuclear Information System (INIS)

Solodukhin, V.P.

2005-01-01

A complex of nuclear-physical methods developed in the Institute of Nuclear Physics of Kazakhstan National Nuclear Center for the investigations of the rate, character and peculiarities of contamination with radionuclides of the Semipalatinsk Nuclear Test Site (SNTS) is presented. The developed method combines both macroinvestigations (radionuclide analysis, NAA, XRFA, ESR- and NGR-spectroscopy) and microinvestigations (MS, micro-PIXE, electron microscopy). The results of the investigations at the main SNTS test sites 'Opytnoye pole' and 'Degelen' are presented. (author)

Lightning vulnerability of nuclear explosive test systems at the Nevada Test Site

International Nuclear Information System (INIS)

Hasbrouck, R.T.

1985-01-01

A task force chartered to evaluate the effects of lightning on nuclear explosives at the Nevada Test Site has made several recommendations intended to provide lightning-invulnerable test device systems. When these recommendations have been implemented, the systems will be tested using full-threat-level simulated lightning

Measurement implications for effective testing in nuclear training

International Nuclear Information System (INIS)

Zaret, R.; Pawlowski, V.

1983-01-01

The primary thrust of this paper is to present an overview of the measurement concepts of reliability and validity. Techniques and issues are presented which will allow Nuclear Training Personnel to have greater confidence in the accuracy of scores obtained from in-house developed tests. While it is realized that the conditions under which tests are developed in Nuclear Training environments are less than ideal, the concepts and techniques addressed can be applied under any conditions

On the population dose around the Semipalatinsk nuclear test site

International Nuclear Information System (INIS)

Hill, P.; Dederichs, H.; Ostapczuk, P.; Hille, R.; Artemev, O.; Ptitskaya, L.; Akhmetov, M.; Pivovarov, S.

2002-01-01

Since 1949 the Semipalatinsk Nuclear Test Site (NTS) was extensively used by the former Soviet government as a testing range for atomic weapons. Atmospheric and underground tests were finally stopped in 1962 and 1989, respectively. The Ministry of the Russian Federation of Atomic Energy officially counts a total of 456 tests, including 116 atmospheric tests. The total yield of the nuclear explosions carried out was 6.3 Megatons equivalent with 6.7 PetaBq of 1 37C s and 3.7 PetaBq of 9 0S r being released into the athmosphere. Some of the athmospheric radioactive tests shielded plumes, which extended far beyond the outer borders of the NTS. Already the first Soviet atomic bomb test on August 29, 1949 due to unfavourable meteorological conditions affected the villages of Dolon and Moistik. Since 1995 joint investigations performed by the Research Centre Julich in cooperation with the Kazakh National Nuclear Centre in the region of the former nuclear test site near Semipalatinsk besides environmental measurents also involve the assessment of the current dose of the population at and around the test site in addition to the important retrospective determination of the dose of persons affected by the atmospheric tests

Layout of the objects of underground nuclear tests at the Balapan test field of the former Semipalatinsk test site

International Nuclear Information System (INIS)

Konovalov, V.E.; Gryaznov, O.V.

2000-01-01

Integrated research of practical and scientific interest is conducted at the Balapan test field of the Semipalatinsk test site. The lack of the reliable locations for features associated with nuclear testing causes considerable difficulties while carrying out the research. To fill this gap the authors present data available at the Institute of Geophysical Research of the National Nuclear Center of the Republic of Kazakhstan. (author)

Introduction to nuclear test engineering

International Nuclear Information System (INIS)

O'Neal, W.C.; Paquette, D.L.

1982-01-01

The basic information in this report is from a vu-graph presentation prepared to acquaint new or prospective employees with the Nuclear Test Engineering Division (NTED). Additional information has been added here to enhance a reader's understanding when reviewing the material after hearing the presentation, or in lieu of attending a presentation

Oral Solid Dosage Form Disintegration Testing - The Forgotten Test.

Science.gov (United States)

Al-Gousous, Jozef; Langguth, Peter

2015-09-01

Since its inception in the 1930s, disintegration testing has become an important quality control (QC) test in pharmaceutical industry, and disintegration test procedures for various dosage forms have been described by the different pharmacopoeias, with harmonization among them still not quite complete. However, because of the fact that complete disintegration does not necessarily imply complete dissolution, much more research has been focused on dissolution rather than on disintegration testing. Nevertheless, owing to its simplicity, disintegration testing seems to be an attractive replacement to dissolution testing as recognized by the International Conference on Harmonization guidelines, in some cases. Therefore, with proper research being carried out to overcome the associated challenges, the full potential of disintegration testing could be tapped saving considerable efforts allocated to QC testing and quality assurance. © 2014 Wiley Periodicals, Inc. and the American Pharmacists Association.

An Evaluation of North Korea’s Nuclear Test by Belbasi Nuclear Tests Monitoring Center-KOERI

Science.gov (United States)

Necmioglu, O.; Meral Ozel, N.; Semin, K.

2009-12-01

Bogazici University and Kandilli Observatory and Earthquake Research Institute (KOERI) is acting as the Turkish National Data Center (NDC) and responsible for the operation of the International Monitoring System (IMS) Primary Seismic Station (PS-43) under Belbasi Nuclear Tests Monitoring Center for the verification of compliance with the Comprehensive Nuclear-Test-Ban Treaty (CTBT) since February 2000. The NDC is responsible for operating two arrays which are part of the IMS, as well as for transmitting data from these stations to the International Data Centre (IDC) in Vienna. The Belbasi array was established in 1951, as a four-element (Benioff 1051) seismic array as part of the United States Atomic Energy Detection System (USAEDS). Turkish General Staff (TGS) and U.S. Air Force Technical Application Center (AFTAC) under the Defense and Economic Cooperation Agreement (DECA) jointly operated this short period array. The station was upgraded and several seismometers were added to array during 1951 and 1994 and the station code was changed from BSRS (Belbasi Seismic Research Station) to BRTR-PS43 later on. PS-43 is composed of two sub-arrays (Ankara and Keskin): the medium-period array with a ~40 km radius located in Ankara and the short-period array with a ~3 km radius located in Keskin. Each array has a broadband element located at the middle of the circular geometry. Short period instruments are installed at depth 30 meters from the surface while medium and broadband instruments are installed at depth 60 meters from surface. On 25 May 2009, The Democratic People’s Republic of Korea (DPRK) claimed that it had conducted a nuclear test. Corresponding seismic event was recorded by IMS and IDC released first automatic estimation of time (00:54:43 GMT), location (41.2896°N and 129.0480°E) and the magnitude (4.52 mb) of the event in less than two hours time (USGS: 00:54:43 GMT; 41.306°N, 129.029°E; 4.7 mb) During our preliminary analysis of the 25th May 2009 DPRK

SCOPE-RADTEST: Radioactivity from nuclear test explosions

International Nuclear Information System (INIS)

Shapiro, C.S.; Tsaturov, Y.

1993-10-01

The SCOPE-RADTEST program consists of an international collaborative study involving Russia, the USA, China, and Kazakhstan. It will focus on the releases of radioactivity that resulted from nuclear test explosions that have taken place at various test sites around the world for peaceful and military purposes. RADTEST will focus on these principal tasks: (1) To inventory data on measurements of radionuclide deposition densities, and identify gaps in these data. (2) To compare old and develop new models of radioactive transport to better understand the deposition densities of radionuclides both on and near the nuclear test sites, including areas downwind where potentially significant episodes of fallout have occurred (such as the Altaj Region of Russia). (3) To study the migration of the radionuclides through the biosphere, including all pathways to humans. This will include the study of the effects on other biota that have impacts on humans. The main focus will be to characterize the nature and magnitude of the dose to humans. This will include dose reconstructions from past events, and also an increased capability for dose prediction from possible future accidental or deliberate explosions. (4)To analyze the data on the effects of these doses (including low doses) on human health. The test sites to be studied would include the Nevada Test Site (USA), South Pacific Islands (USA), Novaja Zemla (Russia), Semipalatinsk (Kazakhstan) and Luc Bu Pu (Lop Nor) (China). Tests at these sites include most of the total of nuclear explosions that have been conducted. Other sites, (including the sites of the U.K. and France), as appropriate, may also be included where tests were conducted for peaceful or military purposes

United States nuclear tests, July 1945 through September 1992

Energy Technology Data Exchange (ETDEWEB)

1994-12-01

This document lists chronologically and alphabetically by name all nuclear tests and simultaneous detonations conducted by the United States from July 1945 through September 1992. Several tests conducted during Operation Dominic involved missile launches from Johnston Atoll. Several of these missile launches were aborted, resulting in the destruction of the missile and nuclear device either on the pad or in the air.

NNWSI waste form performance test development

International Nuclear Information System (INIS)

Bates, J.K.; Gerding, T.J.

1984-01-01

A test method has been developed to measure the release of radionuclides from the waste package under simulated NNWSI repository conditions, and to provide information concerning materials interactions that may occur in the repository. Data from 13 weeks of unsaturated testing are discussed and compared to that from a 13-week analog test. The data indicate that the waste form test is capable of producing consistent, reproducible results that will be useful in evaluating the role of the waste in the long-term performance of the repository. 6 references, 3 figures

Review of Nuclear Thermal Propulsion Ground Test Options

Science.gov (United States)

Coote, David J.; Power, Kevin P.; Gerrish, Harold P.; Doughty, Glen

2015-01-01

High efficiency rocket propulsion systems are essential for humanity to venture beyond the moon. Nuclear Thermal Propulsion (NTP) is a promising alternative to conventional chemical rockets with relatively high thrust and twice the efficiency of highest performing chemical propellant engines. NTP utilizes the coolant of a nuclear reactor to produce propulsive thrust. An NTP engine produces thrust by flowing hydrogen through a nuclear reactor to cool the reactor, heating the hydrogen and expelling it through a rocket nozzle. The hot gaseous hydrogen is nominally expected to be free of radioactive byproducts from the nuclear reactor; however, it has the potential to be contaminated due to off-nominal engine reactor performance. NTP ground testing is more difficult than chemical engine testing since current environmental regulations do not allow/permit open air testing of NTP as was done in the 1960's and 1970's for the Rover/NERVA program. A new and innovative approach to rocket engine ground test is required to mitigate the unique health and safety risks associated with the potential entrainment of radioactive waste from the NTP engine reactor core into the engine exhaust. Several studies have been conducted since the ROVER/NERVA program in the 1970's investigating NTP engine ground test options to understand the technical feasibility, identify technical challenges and associated risks and provide rough order of magnitude cost estimates for facility development and test operations. The options can be divided into two distinct schemes; (1) real-time filtering of the engine exhaust and its release to the environment or (2) capture and storage of engine exhaust for subsequent processing.

Helium leak testing methods in nuclear applications

International Nuclear Information System (INIS)

Ahmad, Anis

2004-01-01

Helium mass-spectrometer leak test is the most sensitive leak test method. It gives very reliable and sensitive test results. In last few years application of helium leak testing has gained more importance due to increased public awareness of safety and environment pollution caused by number of growing chemical and other such industries. Helium leak testing is carried out and specified in most of the critical area applications like nuclear, space, chemical and petrochemical industries

Standard test method for nondestructive assay of special nuclear material holdup using Gamma-Ray spectroscopic methods

CERN Document Server

American Society for Testing and Materials. Philadelphia

2007-01-01

1.1 This test method describes gamma-ray methods used to nondestructively measure the quantity of 235U, or 239Pu remaining as holdup in nuclear facilities. Holdup occurs in all facilities where nuclear material is processed, in process equipment, in exhaust ventilation systems and in building walls and floors. 1.2 This test method includes information useful for management, planning, selection of equipment, consideration of interferences, measurement program definition, and the utilization of resources (1, 2, 3, 4). 1.3 The measurement of nuclear material hold up in process equipment requires a scientific knowledge of radiation sources and detectors, transmission of radiation, calibration, facility operations and error analysis. It is subject to the constraints of the facility, management, budget, and schedule; plus health and safety requirements; as well as the laws of physics. The measurement process includes defining measurement uncertainties and is sensitive to the form and distribution of the material...

Some comments on the behaviour of the excited nuclear matter formed in nuclear collisions at high energies

International Nuclear Information System (INIS)

Besliu, Calin; Jipa, Alexandru; Argintaru, Dan

2003-01-01

In the last years many experiments have been performed in different laboratories to investigate the behaviour of the nuclear matter formed in nuclear collisions at high energies. Therefore, many experimental results are available at present. For explaining these experimental results a lot of models have been proposed. A very large number of concepts have been used. Taking into account some own experimental results obtained in proton-nucleus and nucleus-nucleus collisions at energies between a few A GeV and a few hundred A GeV we comments in the frame a phenomenological geometric picture the main experimental results on charged particle multiplicities, participants, cross sections, momentum spectra, temperature slopes, nuclear matter flow, size and structure of the participant regions, antiparticle to particle ratios and chemical potential. Some jumps in the dependencies of some interesting physical quantities on the available energies in the centre of mass system can be reported. Trends to behaviours like-saturation of some physical quantities are observed, too. Therefore, some connections with the possible phase transitions in nuclear matter are included. A few specific signals of different phase transitions in nuclear matter are suggested. (authors)

Oxygen Containment System Options for Nuclear Thermal Propulsion Testing

Data.gov (United States)

National Aeronautics and Space Administration — All nuclear thermal propulsion (NTP) ground testing conducted in the 1950s and 1960s during the ROVER/(Nuclear Engine Rocket Vehicle Application (NERVA) program...

Determination of chemical forms of 14C in liquid discharges from nuclear power plants.

Science.gov (United States)

Svetlik, I; Fejgl, M; Povinec, P P; Kořínková, T; Tomášková, L; Pospíchal, J; Kurfiřt, M; Striegler, R; Kaufmanová, M

2017-10-01

Developments of radioanalytical methods for determination of radiocarbon in wastewaters from nuclear power plants (NPP) with pressurized light water reactors, which would distinguish between the dissolved organic and inorganic forms have been carried out. After preliminary tests, the method was used to process pilot samples from wastewater outlets from the Temelín and Dukovany NPPs (Czech Republic). The results of analysis of pilot water samples collected in 2015 indicate that the instantaneous 14 C releases into the water streams would be about 7.10 -5 (Temelín) and 4.10 -6 (Dukovany) of the total quantity of the 14 C liberated into the environment. Copyright © 2017 Elsevier Ltd. All rights reserved.

Non Nuclear Testing of Reactor Systems In The Early Flight Fission Test Facilities (EFF-TF)

International Nuclear Information System (INIS)

Van Dyke, Melissa; Martin, James

2004-01-01

The Early Flight Fission-Test Facility (EFF-TF) can assist in the design and development of systems through highly effective non-nuclear testing of nuclear systems when technical issues associated with near-term space fission systems are 'non-nuclear' in nature (e.g. system's nuclear operations are understood). For many systems, thermal simulators can be used to closely mimic fission heat deposition. Axial power profile, radial power profile, and fuel pin thermal conductivity can be matched. In addition to component and subsystem testing, operational and lifetime issues associated with the steady state and transient performance of the integrated reactor module can be investigated. Instrumentation at the EFF-TF allows accurate measurement of temperature, pressure, strain, and bulk core deformation (useful for accurately simulating nuclear behavior). Ongoing research at the EFF-TF is geared towards facilitating research, development, system integration, and system utilization via cooperative efforts with DOE laboratories, industry, universities, and other Nasa centers. This paper describes the current efforts for the latter portion of 2003 and beginning of 2004. (authors)

Summarisation of construction and commissioning experience for nuclear power integrated test facility

International Nuclear Information System (INIS)

Xiao Zejun; Jia Dounan; Jiang Xulun; Chen Bingde

2003-01-01

Since the foundation of Nuclear Power Institute of China, it has successively designed various engineering experimental facilities, and constructed nuclear power experimental research base, and accumulated rich construction experiences of nuclear power integrated test facility. The author presents experience on design, construction and commissioning of nuclear power integrated test facility

Development of an accelerated leach test(s) for low-level waste forms

International Nuclear Information System (INIS)

Dougherty, D.R.; Fuhrmann, M.; Colombo, P.

1986-01-01

An accelerated leach test(s) is being developed to predict long-term leaching behavior of low-level radioactive waste (LLW) forms in their disposal environments. As necessary background, a literature survey of reported leaching mechanisms, available mathematical models and factors that affect leaching of LLW forms has been compiled. Mechanisms which have been identified include diffusion, dissolution, ion exchange, corrosion and surface effects. A computerized data base of LLW leaching data and mathematical models is being developed. The data is being used for model evaluation by curve fitting and statistical analysis according to standard procedures of statistical quality control. Long-term leach tests on portland cement, bitumen and vinyl ester-styrene (VES) polymer waste forms are underway which are designed to identify and evaluate factors that accelerate leaching without changing the mechanisms. Initial results on the effect of temperature on leachability indicate that the leach rates of cement and VES waste forms increase with increasing temperature, whereas, the leach rate of bitumen is little affected

Animal Effects from Soviet Atmospheric Nuclear Tests

Science.gov (United States)

2008-03-01

describes the effect on animal models of atmospheric nuclear weapons tests performed by the Soviet Union at the Semipalatinsk Test Site . Part I describes...understand the pathogenic mechanisms of injury and the likelihood of efficacy of proposed treatment measures. 15. SUBJECT TERMS Semipalatinsk Test Site ...the Semipalatinsk Test Site . Part 1 describes the air blast and thermal radiation effects. Part 2 covers the effects of primary (prompt) radiation and

Development of Welding and Instrumentation Technology for Nuclear Fuel Test Rod

International Nuclear Information System (INIS)

Joung, Chang Young; Ahn, Sung Ho; Heo, Sung Ho; Hong, Jin Tae; Kim, Ka Hye

2013-01-01

It is necessary to develop various types of welding, instrumentation and helium gas filling techniques that can conduct TIG spot welding exactly at a pin-hole of the end-cap on the nuclear fuel rod to fill up helium gas. The welding process is one of the most important among the instrumentation processes of the nuclear fuel test rod. To manufacture the nuclear fuel test rod, a precision welding system needs to be fabricated to develop various welding technologies of the fuel test rod jointing the various sensors and end-caps on a fuel cladding tube, which is charged with fuel pellets and component parts. We therefore designed and fabricated an orbital TIG welding system and a laser welding system. This paper describes not only some experiment results from weld tests for the parts of a nuclear fuel test rod, but also the contents for the instrumentation process of the dummy fuel test rod installed with the C-type T. C. A dummy nuclear fuel test rod was successfully fabricated with the welding and instrumentation technologies acquired with various tests. In the test results, the round welding has shown a good weldability at both the orbital TIG welding system and the fiber laser welding system. The spot welding to fill up helium gas has shown a good welding performance at a welding current of 30A, welding time of 0.4 sec and gap of 1 mm in a helium gas atmosphere. The soundness of the nuclear fuel test rod sealed by a mechanical sealing method was confirmed by helium leak tests and microstructural analyses

Development of Welding and Instrumentation Technology for Nuclear Fuel Test Rod

Energy Technology Data Exchange (ETDEWEB)

Joung, Chang Young; Ahn, Sung Ho; Heo, Sung Ho; Hong, Jin Tae; Kim, Ka Hye [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

2013-10-15

It is necessary to develop various types of welding, instrumentation and helium gas filling techniques that can conduct TIG spot welding exactly at a pin-hole of the end-cap on the nuclear fuel rod to fill up helium gas. The welding process is one of the most important among the instrumentation processes of the nuclear fuel test rod. To manufacture the nuclear fuel test rod, a precision welding system needs to be fabricated to develop various welding technologies of the fuel test rod jointing the various sensors and end-caps on a fuel cladding tube, which is charged with fuel pellets and component parts. We therefore designed and fabricated an orbital TIG welding system and a laser welding system. This paper describes not only some experiment results from weld tests for the parts of a nuclear fuel test rod, but also the contents for the instrumentation process of the dummy fuel test rod installed with the C-type T. C. A dummy nuclear fuel test rod was successfully fabricated with the welding and instrumentation technologies acquired with various tests. In the test results, the round welding has shown a good weldability at both the orbital TIG welding system and the fiber laser welding system. The spot welding to fill up helium gas has shown a good welding performance at a welding current of 30A, welding time of 0.4 sec and gap of 1 mm in a helium gas atmosphere. The soundness of the nuclear fuel test rod sealed by a mechanical sealing method was confirmed by helium leak tests and microstructural analyses.

Annual report on the development and characterization of solidified forms for nuclear wastes, 1979

International Nuclear Information System (INIS)

Chick, L.A.; McVay, G.L.; Mellinger, G.B.; Roberts, F.P.

1980-12-01

Development and characterization of solidified nuclear waste forms is a major continuing effort at Pacific Northwest Laboratory. Contributions from seven programs directed at understanding chemical composition, process conditions, and long-term behaviors of various nuclear waste forms are included in this report. The major findings of the report are included in extended figure captions that can be read as brief technical summaries of the research, with additional information included in a traditional narrative format. Waste form development proceeded on crystalline and glass materials for high-level and transuranic (TRU) wastes. Leaching studies emphasized new areas of research aimed at more basic understanding of waste form/aqueous solution interactions. Phase behavior and thermal effects research included studies on crystal phases in defense and TRU waste glasses and on liquid-liquid phase separation in borosilicate waste glasses. Radiation damage effects in crystals and glasses from alpha decay and from transmutation are reported

Dose Prediction for surface nuclear explosions: case studies for Semipalatinsk and Lop Nur tests

International Nuclear Information System (INIS)

Takada, Jun

2008-01-01

Dose prediction method RAPS after surface nuclear explosion has been developed by using the empirical dose function of USA nuclear test. This method which provides us external total dose, dose rate at any distant, at any time for any yield of nuclear explosion, is useful for radiation protection in case of nuclear events such as terrorism and nuclear war. The validity of RAPS has been confirmed by application to historical surface nuclear test explosions. The first test case study which was done for the first test explosion of the former USSR at the Semipalatinsk Nuclear Test Site on August 29th 1949, shows a good agreement with luminescence dosimetry on a brick. This dose prediction method was applied nuclear tests in Lop Nur. The results indicate dangerous nuclear radiation influences including fatal risk in the wide Uygur area. (author)

On the hydrostatic test for nuclear vessels

International Nuclear Information System (INIS)

Palmero, A.

1979-01-01

A comparison of the pressure test requirements, namely specified values of pressure and temperature, for nuclear vessels designed and constructed according to the ASME Code and Spanish Rules is presented. Also the relationship of the design criteria and the pressure test requirements is indicated with a particular emphasis on the test temperature in order to avoid brittle behaviour of the materials. (author)

Nuclear waste repository transparency technology test bed demonstrations at WIPP

International Nuclear Information System (INIS)

Betsill J, David; Elkins, Ned Z.; Wu, Chuan-Fu; Mewhinney, James D.; Aamodt, Paul

2000-01-01

Secretary of Energy, Bill Richardson, has stated that one of the nuclear waste legacy issues is ''The challenge of managing the fuel cycle's back end and assuring the safe use of nuclear power.'' Waste management (i.e., the back end) is a domestic and international issue that must be addressed. A key tool in gaining acceptance of nuclear waste repository technologies is transparency. Transparency provides information to outside parties for independent assessment of safety, security, and legitimate use of materials. Transparency is a combination of technologies and processes that apply to all elements of the development, operation, and closure of a repository system. A test bed for nuclear repository transparency technologies has been proposed to develop a broad-based set of concepts and strategies for transparency monitoring of nuclear materials at the back end of the fuel/weapons cycle. WIPP is the world's first complete geologic repository system for nuclear materials at the back end of the cycle. While it is understood that WIPP does not currently require this type of transparency, this repository has been proposed as realistic demonstration site to generate and test ideas, methods, and technologies about what transparency may entail at the back end of the nuclear materials cycle, and which could be applicable to other international repository developments. An integrated set of transparency demonstrations was developed and deployed during the summer, and fall of 1999 as a proof-of-concept of the repository transparency technology concept. These demonstrations also provided valuable experience and insight into the implementation of future transparency technology development and application. These demonstrations included: Container Monitoring Rocky Flats to WIPP; Underground Container Monitoring; Real-Time Radiation and Environmental Monitoring; Integrated level of confidence in the system and information provided. As the world's only operating deep geologic

US Underground Nuclear Test History Reports

Science.gov (United States)

History Documents US Underground Nuclear Test History Reports NTPR Radiation Exposure Reports Enewetak Atoll Cleanup Documents TRAC About Who We Are Our Values History Locations Our Leadership Director Support Center Contact Us FAQ Sheet Links Success Stories Contracts Business Opportunities Current

Overview of factors affecting the leachability of nuclear waste forms

International Nuclear Information System (INIS)

Stone, J.A.

1980-01-01

An overview of various factors that affect the leachability of nuclear waste forms is presented. The factors affect primarily the leaching system (temperature, for example), the leachant (pH, for example), or the solid being leached (surface condition, for example). A qualitative understanding exists of the major factors affecting leaching, but further studies are needed to establish leaching mechanisms and develop predictive models. 67 refs

A new Krakow scanning nuclear microprobe performance tests and early application experienc

CERN Document Server

Lebed, S; Polak, W; Potempa, A W; Stachura, Z; Paszkowski, M

2001-01-01

A new scanning nuclear microprobe (MP) with a short-length probe forming system was designed,installed and tested at the 3MV Van de Graaff accelerator in Krakow.The MP resolution of 3.3 mu m was reached for 2.4 MeV proton beam in the high-current mode (>= 100pA).The MP facility provides a local,non-destructive,quantitative elemental microanalysis using a Proton Induced X-ray Emission (PIXE) technique.As example of possible application an analysis of a geological sample containing monazite crystals investigated by PIXE method is presented.

Low-risk alternative waste forms for problematic high-level and long-lived nuclear wastes

International Nuclear Information System (INIS)

Stewart, M.W.A.; Begg, B.D.; Moricca, S.; Day, R.A.

2006-01-01

Full text: The highest cost component the nuclear waste clean up challenge centres on high-level waste (HLW) and consequently the greatest opportunity for cost and schedule savings lies with optimising the approach to HLW cleanup. The waste form is the key component of the immobilisation process. To achieve maximum cost savings and optimum performance the selection of the waste form should be driven by the characteristics of the specific nuclear waste to be immobilised, rather than adopting a single baseline approach. This is particularly true for problematic nuclear wastes that are often not amenable to a single baseline approach. The use of tailored, high-performance, alternative waste forms that include ceramics and glass-ceramics, coupled with mature process technologies offer significant performance improvements and efficiency savings for a nuclear waste cleanup program. It is the waste form that determines how well the waste is locked up (chemical durability), and the number of repository disposal canisters required (waste loading efficiency). The use of alternative waste forms for problematic wastes also lowers the overall risk by providing high performance HLW treatment alternatives. The benefits tailored alternative waste forms bring to the HLW cleanup program will be briefly reviewed with reference to work carried out on the following: The HLW calcines at the Idaho National Laboratory; SYNROC ANSTO has developed a process utilising a glass-ceramic combined with mature hot-isostatic pressing (HIP) technology and has demonstrated this at a waste loading of 80 % and at a 30 kg HIP scale. The use of this technology has recently been estimated to result in a 70 % reduction in waste canisters, compared to the baseline borosilicate glass technology; Actinide-rich waste streams, particularly the work being done by SYNROC ANSTO with Nexia Solutions on the Plutonium-residues wastes at Sellafield in the UK, which if implemented is forecast to result in substantial

Testing a CANDU-fueling machine at the Institute for Nuclear Research Pitesti

International Nuclear Information System (INIS)

Cojocaru, Virgil

2006-01-01

In 2003, as a national and European premiere, the Fueling Machine Head no. 4 (F/M) for the Nuclear Power Plant Cernavoda Unit 2 (NPP) was successfully tested at the Institute for Nuclear Research Pitesti (INR). In 2005, the second Fueling Machine (no. 5) has tested for the Nuclear Power Plant Cernavoda Unit 2. The Institute's main objective is to develop scientific and technological support for the Romanian Nuclear Power Program. Testing the Fueling Machines at INR Pitesti is part of the overall program to assimilate the CANDU technology in Romania. To perform the tests of these machines at INR Pitesti, a special testing rig has built being available for this goal. Both the testing rig and staff had successfully assessed by the AECL representatives during two missions. There was a delivery contract between GEC Canada and Nuclear Power Plant Cernavoda - Unit 2 to provide the Fueling Machines no. 4 and no. 5 in Romania before testing activity. As a first conclusion, the Institute for Nuclear Research Pitesti has the facilities, the staff and the experience to perform possible co-operations with any CANDU Reactor owner

Advancing nuclear technology and research. The advanced test reactor national scientific user facility

Energy Technology Data Exchange (ETDEWEB)

Benson, Jeff B; Marshall, Frances M [Idaho National Laboratory, Idaho Falls, ID (United States); Allen, Todd R [Univ. of Wisconsin, Madison, WI (United States)

2012-03-15

The Advanced Test Reactor (ATR), at the Idaho National Laboratory (INL), is one of the world's premier test reactors for providing the capability for studying the effects of intense neutron and gamma radiation on reactor materials and fuels. The INL also has several hot cells and other laboratories in which irradiated material can be examined to study material radiation effects. In 2007 the US Department of Energy (DOE) designated the ATR as a National Scientific User Facility (NSUF) to facilitate greater access to the ATR and the associated INL laboratories for material testing research. The mission of the ATR NSUF is to provide access to world-class facilities, thereby facilitating the advancement of nuclear science and technology. Cost free access to the ATR, INL post irradiation examination facilities, and partner facilities is granted based on technical merit to U.S. university-led experiment teams conducting non-proprietary research. Proposals are selected via independent technical peer review and relevance to United States Department of Energy. To increase overall research capability, ATR NSUF seeks to form strategic partnerships with university facilities that add significant nuclear research capability to the ATR NSUF and are accessible to all ATR NSUF users. (author)

A perspective on atomspheric nuclear tests in Nevada fact book

International Nuclear Information System (INIS)

Friesen, H.N.

1992-04-01

This Fact Book provides historical background and perspective on the nuclear testing program at the Nevada Test Site (NTS). Nuclear tests contributing to the off-site deposition of radioactive fallout are identified, and the concept of cumulative estimated exposure is explained. The difficulty of associating health effects with radiation is presented also. The status of litigation against the government and legislation (as of December 1991) are summarized

Role of testing in requalifying Transamerica Delaval, Inc., engines for nuclear service

International Nuclear Information System (INIS)

Nesbitt, J.F.; Dingee, D.A.; Laity, W.W.

1985-03-01

This paper discusses the role of testing in requalifying Transamerica Delaval, Inc. (TDI) diesel generators for use as emergency standby power sources at nuclear power plants. ''Lead'' engine tests (to confirm the design adequacy of key engine components under conditions that could induce high-cycle fatigue) and ''following'' engine tests (for engines of the same model and equipped with the same components as the ''lead'' engine) have been conducted at several nuclear power plants. The tests conducted by Duke Power Company (Catawba Nuclear Station Unit 1) and Long Island Lighting Company (Shoreham Nuclear Power Station Unit 1) are discussed. 2 refs

Testing and operation of nuclear air-cleaning systems in Qinshan NPP

International Nuclear Information System (INIS)

Yang Lin

1993-01-01

The components of nuclear air-cleaning system, system function, operational mode and the performance of cleaning components in Qinshan Nuclear Power Plant are described. The items, purpose, methods and results of in-place testing after the installation are also described in detail. The in-place testing verifies that nuclear air-cleaning systems in Qinshan Nuclear Power Plant are reliable and high effective. It also describes the points of the operational management. It is shown that the good operational management is the key which developed prescription function of nuclear air-cleaning systems. At present, Qinshan Nuclear Power Plant will be in full power, the normal operation of the system is satisfied with the demand of safe operation in Qinshan Nuclear Power Company

Pump testing in the nuclear industry: The comprehensive test and other considerations

International Nuclear Information System (INIS)

Hoyle, T.F.

1992-01-01

The American Society of Mechanical Engineers Operations and Maintenance Working Group on Pumps and Valves is working on a revision to their pump testing Code, ISTB-1990. This revision will change the basic philosophy of pump testing in the nuclear industry. Currently, all pumps are required to be tested quarterly, except those installed in dry sumps. In the future standby pumps will receive only a start test quarterly to ensure the pump comes up to speed and pressure or flow. Then, on a biennial basis all pumps would receive a more extensive test. This comprehensive test would require high accuracy test gauges to be used, and the pumps would be required to be tested near pump design flow. Testing on minimum flow loops would not be permitted except in rare cases. Additionally. during the comprehensive test, measurements of vibration, flow, and pressure would all be taken. The OM-6 standard (ISTB Code) will also require that reference values of flow rate and differential pressure be taken at several points instead of just one point, which is current practice. The comprehensive test is just one step in ensuring the adequacy of pump testing in the nuclear industry. This paper also addresses other concerns and makes recommendations for increased quality of testing of certain critical pumps and recommendations for less stringent or no tests on less critical pumps

Nuclear Test-Experimental Science: Annual report, fiscal year 1988

Energy Technology Data Exchange (ETDEWEB)

Struble, G.L.; Donohue, M.L.; Bucciarelli, G.; Hymer, J.D.; Kirvel, R.D.; Middleton, C.; Prono, J.; Reid, S.; Strack, B. (eds.)

1988-01-01

Fiscal year 1988 has been a significant, rewarding, and exciting period for Lawrence Livermore National Laboratory's nuclear testing program. It was significant in that the Laboratory's new director chose to focus strongly on the program's activities and to commit to a revitalized emphasis on testing and the experimental science that underlies it. It was rewarding in that revolutionary new measurement techniques were fielded on recent important and highly complicated underground nuclear tests with truly incredible results. And it was exciting in that the sophisticated and fundamental problems of weapons science that are now being addressed experimentally are yielding new challenges and understanding in ways that stimulate and reward the brightest and best of scientists. During FY88 the program was reorganized to emphasize our commitment to experimental science. The name of the program was changed to reflect this commitment, becoming the Nuclear Test-Experimental Science (NTES) Program.

The behavior of fission products during nuclear rocket reactor tests

International Nuclear Information System (INIS)

Bokor, P.C.; Kirk, W.L.; Bohl, R.J.

1991-01-01

Fission product release from nuclear rocket propulsion reactor fuel is an important consideration for nuclear rocket development and application. Fission product data from the last six reactors of the Rover program are collected in this paper to provide as basis for addressing development and testing issues. Fission product loss from the fuel will depend on fuel composition and reactor design and operating parameters. During ground testing, fission products can be contained downstream of the reactor. The last Rover reactor tested, the Nuclear Furnance, was mated to an effluent clean-up system that was effective in preventing the discharge of fission products into the atmosphere

Testing competing forms of the Milankovitch hypothesis

DEFF Research Database (Denmark)

Kaufmann, Robert K.; Juselius, Katarina

2016-01-01

We test competing forms of the Milankovitch hypothesis by estimating the coefficients and diagnostic statistics for a cointegrated vector autoregressive model that includes 10 climate variables and four exogenous variables for solar insolation. The estimates are consistent with the physical...... ice volume and solar insolation. The estimated adjustment dynamics show that solar insolation affects an array of climate variables other than ice volume, each at a unique rate. This implies that previous efforts to test the strong form of the Milankovitch hypothesis by examining the relationship...... that the latter is consistent with a weak form of the Milankovitch hypothesis and that it should be restated as follows: Internal climate dynamics impose perturbations on glacial cycles that are driven by solar insolation. Our results show that these perturbations are likely caused by slow adjustment between land...

78 FR 25488 - Qualification Tests for Safety-Related Actuators in Nuclear Power Plants

Science.gov (United States)

2013-05-01

... Nuclear Power Plants AGENCY: Nuclear Regulatory Commission. ACTION: Draft regulatory guide; request for... regulatory guide (DG), DG-1235, ``Qualification Tests for Safety-Related Actuators in Nuclear Power Plants... entitled ``Qualification Tests for Safety-Related Actuators in Nuclear Power Plants'' is temporarily...

Development of an accelerated leach test(s) for low-level waste forms

International Nuclear Information System (INIS)

Dougherty, D.R.; Fuhrmann, M.; Colombo, P.

1985-01-01

An accelerated leach test(s) is being developed to predict long-term leaching behavior of low-level radioactive waste (LLW) forms in their disposal environments. As necessary background, a literature survey of reported leaching mechanisms, available mathematical models and factors that affect leaching of LLW forms has been compiled. Mechanisms which have been identified include diffusion, dissolution, ion exchange, corrosion and surface effects. A computerized data base of LLW leaching data and mathematical models is being developed. The data is being used for model evaluation by curve fitting and statistical analysis according to standard procedures of statistical quality control. Long-term leach tests on portland cement, bitumen and vinyl ester-styrene (VES) polymer waste forms are underway which are designed to identify and evaluate factors that accelerate leaching without changing the mechanisms. Initial results on the effect of temperature on leachability indicate that the leach rates of cement and VES waste forms increase with increasing temperature, whereas, the leach rate of bitumen is little affected. 10 refs., 5 figs

Test Report of Special Form Qualification Testing for the ORNL U ZipCan

Energy Technology Data Exchange (ETDEWEB)

Martinez, Oscar A. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States)

2017-09-01

This test report describes the special form testing activities performed on the two ZiPCans. One prototype test unit was subjected to the tests stipulated by 10 CFR 71.75 (d)(1)(i), ISO 2919:1999(E) Class 4 impact test, along with the leak rate test specified in 49 CFR 173.469(a)(4)(i). The other test unit was subjected to a leak rate test as specified in 173.469(a)(4)(i) and a heat test as specified in 49 CFR 173.469 (b)(4). Each test unit was leak tested before and after these respective tests. The leak rate tests performed were helium back-pressure tests and bubble tests, as specified in ANSI N14.5-2014.The measured leak rates were converted to standard condition leak rates as specified in ASTM E 493. The determined standardized leak rates from the test and calculation for both test units met the requirements for special form certification.

Construction of solid waste form test facility

International Nuclear Information System (INIS)

Park, Hyun Whee; Lee, Kang Moo; Koo, Jun Mo; Jung, In Ha; Lee, Jong Ryeul; Kim, Sung Whan; Bae, Sang Min; Cho, Kang Whon; Sung, Suk Jong

1989-02-01

The Solid Waste Form Test Facility (SWFTF) is now construction at DAEDUCK in Korea. In SWFTF, the characteristics of solidified waste products as radiological homogeneity, mechanical and thermal property, water resistance and lechability will be tested and evaluated to meet conditions for long-term storage or final disposal of wastes. The construction of solid waste form test facility has been started with finishing its design of a building and equipments in Sep. 1984, and now building construction is completed. Radioactive gas treatment system, extinguishers, cooling and heating system for the facility, electrical equipments, Master/Slave manipulator, power manipulator, lead glass and C.C.T.V. has also been installed. SWFTF will be established in the beginning of 1990's. At this report, radiation shielding door, nondestructive test of the wall, instrumentation system for the utility supply system and cell lighting system are described. (Author)

Testing the Weak Form Efficiency of Karachi Stock Exchange

Directory of Open Access Journals (Sweden)

Muhammad Arshad Haroon

2012-12-01

Full Text Available In an efficient market, share prices reflect all available information. The study of efficient market hypothesis helps to take right decisions related to investments. In this research,weak form efficiency has been tested of Karachi Stock Exchange—KSE covering the period of 2nd November 1991 to 2nd November 2011. Descriptive statistics indicated the absence of weak form efficiency while results of non-parametric tests, showed consistency as well. We employed non-parametric tests were KS Goodness-of-Fit test,run test and autocorrelation test to find out serial independency of the data. Results prove that KSE is not weak-form-efficient. This happens because KSE is an emerging market and there, it has been observed that information take time to be processed. Thus it can besaid that technical analysis may be applied to gain abnormal returns.

Ground test facilities for evaluating nuclear thermal propulsion engines and fuel elements

International Nuclear Information System (INIS)

Allen, G.C.; Beck, D.F.; Harmon, C.D.; Shipers, L.R.

1992-01-01

Interagency panels evaluating nuclear thermal propulsion development options have consistently recognized the need for constructing a major new ground test facility to support fuel element and engine testing. This paper summarizes the requirements, configuration, and design issues of a proposed ground test complex for evaluating nuclear thermal propulsion engines and fuel elements being developed for the Space Nuclear Thermal Propulsion (SNTP) program. 2 refs

North Korea’s 2009 Nuclear Test: Containment, Monitoring, Implications

Science.gov (United States)

2010-04-02

inspections as prima facie evidence of a violation. One generally-accepted means of evading detection of nuclear tests, especially low-yield tests...In an attempt to extend these bans to cover all nuclear tests, negotiations on the CTBT were completed in 1996. The treaty’s basic obligation is to...Verification refers to determining whether a nation is in compliance with its treaty obligations , which in this case means determining whether a suspicious

Individual dose reconstruction among residents living in the vicinity of the Semipalatinsk nuclear test site using EPR spectroscopy of tooth enamel.

Science.gov (United States)

Ivannikov, A I; Zhumadilov, Zh; Gusev, B I; Miyazawa, Ch; Jiao, L; Skvortsov, V G; Stepanenko, V F; Takada, J; Hoshi, M

2002-08-01

Individual accumulated doses were determined by EPR spectroscopy of tooth enamel for 26 adult persons residing in territories adjacent to the Semipalatinsk Nuclear Test Site (SNTS). The absorbed dose values due to radiation from nuclear tests were obtained after subtracting the contribution of natural background radiation from the total accumulated dose. The determined dose values ranged up to 250 mGy, except for one person from Semipalatinsk city with a measured dose of 2.8 +/- 0.4 Gy. Increased dose values were determined for the individuals whose teeth were formed before 1962, the end of the atmospheric nuclear tests. These values were found to be significantly larger than those obtained for a group of younger residents of heavily exposed territories and the residents of territories not exposed to radioactive fallout. These increased dose values are consistent with those based on officially registered data for the Northeastern part of Kazakstan adjacent to SNTS, which was exposed to high levels of radioactive fallout from nuclear tests in period 1949-1962.

The Advanced Test Reactor National Scientific User Facility Advancing Nuclear Technology

International Nuclear Information System (INIS)

Allen, T.R.; Benson, J.B.; Foster, J.A.; Marshall, F.M.; Meyer, M.K.; Thelen, M.C.

2009-01-01

projects and faculty/staff exchanges. In June of 2008, the first week-long ATR NSUF Summer Session was attended by 68 students, university faculty and industry representatives. The Summer Session featured presentations by 19 technical experts from across the country and covered topics including irradiation damage mechanisms, degradation of reactor materials, LWR and gas reactor fuels, and non-destructive evaluation. High impact research results from leveraging the entire research infrastructure, including universities, industry, small business, and the national laboratories. To increase overall research capability, ATR NSUF seeks to form strategic partnerships with university facilities that add significant nuclear research capability to the ATR NSUF and are accessible to all ATR NSUF users. Current partner facilities include the MIT Reactor, the University of Michigan Irradiated Materials Testing Laboratory, the University of Wisconsin Characterization Laboratory, and the University of Nevada, Las Vegas transmission Electron Microscope User Facility. Needs for irradiation of material specimens at tightly controlled temperatures are being met by dedication of a large in-pile pressurized water loop facility for use by ATR NSUF users. Several environmental mechanical testing systems are under construction to determine crack growth rates and fracture toughness on irradiated test systems.

Standard leach tests for nuclear waste materials

International Nuclear Information System (INIS)

Strachan, D.M.; Barnes, B.O.; Turcotte, R.P.

1980-01-01

Five leach tests were conducted to study time-dependent leaching of waste forms (glass). The first four tests include temperature as a variable and the use of three standard leachants. Three of the tests are static and two are dynamic (flow). This paper discusses the waste-form leach tests and presents some representative data. 4 figures

The consequences of underground nuclear testing in French Polynesia

International Nuclear Information System (INIS)

Brown, E.T.

1998-01-01

France began atmospheric nuclear testing at Mururoa and Fangataufa atolls in the South Pacific in July 1966. Following international protest, atmospheric testing ceased in August 1970. In late 1995, an International Geomechanical Commission (IGC) was created to assess the short- and long-term effects of underground nuclear testing on the stability and hydrology of Mururoa and Fangataufa. With the aid of its consultants, the Commission sought to develop its own understanding of the mechanics and consequences of the underground nuclear tests. It carried out extensive numerical analyses of shock wave effects, seismic wave propagation, slope stability and pre- and post-test hydrology. However, in its studies, the IGC was constrained to use the data made available to it by the French authorities. The Commission's report (International Geomechanical Commission 1998) has been submitted to the French Government. This article draws heavily on parts of that report. The Commission's observations and analyses show that there has been no apparent change, on the atoll scale, to the overall mechanical stability of either atoll as a consequence of the underground nuclear tests. The main observable consequences of the tests are underwater slope failures, open fractures on the rim surface and surface settlements. The fractures visible on the surface are generally associated with subsurface slope displacements and occur only in the carbonates. There is no evidence that slope failures or settlements have occurred in the underlying volcanics. There has been no significant change in the long-term (beyond 500 years) hydrology of either atoll. The IGC estimates that the long-term change in the natural groundwater flow will be no more than 1%. There are, however, significant short-term changes locally around the test sites, which are briefly outlined

Comprehensive Test Ban Treaty: options before nuclear Pakistan

International Nuclear Information System (INIS)

Pattanaik, Smruti S.

1998-01-01

The post-nuclear period has rendered Pakistan's strategic calculations more vulnerable. The decision to go nuclear after seventeen days of debate have started proving costly to Pakistan. This is revealed by the economic crisis resulting out of the foreign currency shortage, leading the country to default on the payment of debts. The pressure imposed by the International Monetary Fund (IMF) and World Bank and their patrons to sign the Comprehensive Test Ban Treaty (CTBT) have exposed Pakistan's economic vulnerability. Under this growing pressure, many have started questioning the decision to go nuclear

Minerals and design of new waste forms for conditioning nuclear waste

Science.gov (United States)

Montel, Jean-Marc

2011-02-01

Safe storage of radioactive waste is a major challenge for the nuclear industry. Mineralogy is a good basis for designing ceramics, which could eventually replace nuclear glasses. This requires a new storage concept: separation-conditioning. Basic rules of crystal chemistry allow one to select the most suitable structures and natural occurrences allow assessing the long-term performance of ceramics in a geological environment. Three criteria are of special interest: compatibility with geological environment, resistance to natural fluids, and effects of self-irradiation. If mineralogical information is efficient for predicting the behaviour of common, well-known minerals, such as zircon, monazite or apatite, more research is needed to rationalize the long-term behaviour of uncommon waste form analogs.

Module Testing Techniques for Nuclear Safety Critical Software Using LDRA Testing Tool

International Nuclear Information System (INIS)

Moon, Kwon-Ki; Kim, Do-Yeon; Chang, Hoon-Seon; Chang, Young-Woo; Yun, Jae-Hee; Park, Jee-Duck; Kim, Jae-Hack

2006-01-01

The safety critical software in the I and C systems of nuclear power plants requires high functional integrity and reliability. To achieve those requirement goals, the safety critical software should be verified and tested according to related codes and standards through verification and validation (V and V) activities. The safety critical software testing is performed at various stages during the development of the software, and is generally classified as three major activities: module testing, system integration testing, and system validation testing. Module testing involves the evaluation of module level functions of hardware and software. System integration testing investigates the characteristics of a collection of modules and aims at establishing their correct interactions. System validation testing demonstrates that the complete system satisfies its functional requirements. In order to generate reliable software and reduce high maintenance cost, it is important that software testing is carried out at module level. Module testing for the nuclear safety critical software has rarely been performed by formal and proven testing tools because of its various constraints. LDRA testing tool is a widely used and proven tool set that provides powerful source code testing and analysis facilities for the V and V of general purpose software and safety critical software. Use of the tool set is indispensable where software is required to be reliable and as error-free as possible, and its use brings in substantial time and cost savings, and efficiency

DURABILITY TESTING OF FLUIDIZED BED STEAM REFORMER (FBSR) WASTE FORMS

International Nuclear Information System (INIS)

Jantzen, C

2006-01-01

Fluidized Bed Steam Reforming (FBSR) is being considered as a potential technology for the immobilization of a wide variety of high sodium aqueous radioactive wastes. The addition of clay and a catalyst as co-reactants converts high sodium aqueous low activity wastes (LAW) such as those existing at the Hanford and Idaho DOE sites to a granular ''mineralized'' waste form that may be made into a monolith form if necessary. Simulant Hanford and Idaho high sodium wastes were processed in a pilot scale FBSR at Science Applications International Corporation (SAIC) Science and Technology Applications Research (STAR) facility in Idaho Falls, ID. Granular mineral waste forms were made from (1) a basic Hanford Envelope A low-activity waste (LAW) simulant and (2) an acidic INL simulant commonly referred to as sodium-bearing waste (SBW). The FBSR waste forms were characterized and the durability tested via ASTM C1285 (Product Consistency Test), the Environmental Protection Agency (EPA) Toxic Characteristic Leaching Procedure (TCLP), and the Single Pass Flow Through (SPFT) test. The durability of the FBSR waste form products was tested in order to compare the measured durability to previous FBSR waste form testing on Hanford Envelope C waste forms that were made by THOR Treatment Technologies (TTT) and to compare the FBSR durability to vitreous LAW waste forms, specifically the Hanford low activity waste (LAW) glass known as the Low-activity Reference Material (LRM). The durability of the FBSR waste form is comparable to that of the LRM glass for the test responses studied

Fabrication and Testing of CERMET Fuel Materials for Nuclear Thermal Propulsion

Science.gov (United States)

Hickman, Robert; Broadway, Jeramie; Mireles, Omar

2012-01-01

A first generation Nuclear Cryogenic Propulsion Stage (NCPS) based on Nuclear Thermal Propulsion (NTP) is currently being developed for Advanced Space Exploration Systems. The overall goal of the project is to address critical NTP technology challenges and programmatic issues to establish confidence in the affordability and viability of NTP systems. The current technology roadmap for NTP identifies the development of a robust fuel form as a critical near term need. The lack of a qualified nuclear fuel is a significant technical risk that will require a considerable fraction of program resources to mitigate. Due to these risks and the cost for qualification, the development and selection of a primary fuel must begin prior to Authority to Proceed (ATP) for a specific mission. The fuel development is a progressive approach to incrementally reduce risk, converge the fuel materials, and mature the design and fabrication process of the fuel element. A key objective of the current project is to advance the maturity of CERMET fuels. The work includes fuel processing development and characterization, fuel specimen hot hydrogen screening, and prototypic fuel element testing. Early fuel materials development is critical to help validate requirements and fuel performance. The purpose of this paper is to provide an overview and status of the work at Marshall Space Flight Center (MSFC).

The environment of the nuclear test sites on Novaya Zemlya

International Nuclear Information System (INIS)

Skorve, J.

1995-01-01

A Norwegian study of the effects of Soviet nuclear testing on the arctic island of Novaya Zemlya is underway. The study has used aerial photographs and satellite images and has revealed major rockslides and crater features that may be attributable to testing. It has been claimed that underground testing carries little risk of post-explosion contaminant release, as the explosion vitrifies and seals the surrounding rock mass. Some experts doubt the validity of this claim, and elucidation of the hydrogeological aspects of such nuclear testing is one of the aims of the study

Secondary waste form testing: ceramicrete phosphate bonded ceramics

International Nuclear Information System (INIS)

Singh, D.; Ganga, R.; Gaviria, J.; Yusufoglu, Y.

2011-01-01

The cleanup activities of the Hanford tank wastes require stabilization and solidification of the secondary waste streams generated from the processing of the tank wastes. The treatment of these tank wastes to produce glass waste forms will generate secondary wastes, including routine solid wastes and liquid process effluents. Liquid wastes may include process condensates and scrubber/off-gas treatment liquids from the thermal waste treatment. The current baseline for solidification of the secondary wastes is a cement-based waste form. However, alternative secondary waste forms are being considered. In this regard, Ceramicrete technology, developed at Argonne National Laboratory, is being explored as an option to solidify and stabilize the secondary wastes. The Ceramicrete process has been demonstrated on four secondary waste formulations: baseline, cluster 1, cluster 2, and mixed waste streams. Based on the recipes provided by Pacific Northwest National Laboratory, the four waste simulants were prepared in-house. Waste forms were fabricated with three filler materials: Class C fly ash, CaSiO 3 , and Class C fly ash + slag. Optimum waste loadings were as high as 20 wt.% for the fly ash and CaSiO 3 , and 15 wt.% for fly ash + slag filler. Waste forms for physical characterizations were fabricated with no additives, hazardous contaminants, and radionuclide surrogates. Physical property characterizations (density, compressive strength, and 90-day water immersion test) showed that the waste forms were stable and durable. Compressive strengths were >2,500 psi, and the strengths remained high after the 90-day water immersion test. Fly ash and CaSiO 3 filler waste forms appeared to be superior to the waste forms with fly ash + slag as a filler. Waste form weight loss was ∼5-14 wt.% over the 90-day immersion test. The majority of the weight loss occurred during the initial phase of the immersion test, indicative of washing off of residual unreacted binder components from

Secondary waste form testing : ceramicrete phosphate bonded ceramics.

Energy Technology Data Exchange (ETDEWEB)

Singh, D.; Ganga, R.; Gaviria, J.; Yusufoglu, Y. (Nuclear Engineering Division); ( ES)

2011-06-21

The cleanup activities of the Hanford tank wastes require stabilization and solidification of the secondary waste streams generated from the processing of the tank wastes. The treatment of these tank wastes to produce glass waste forms will generate secondary wastes, including routine solid wastes and liquid process effluents. Liquid wastes may include process condensates and scrubber/off-gas treatment liquids from the thermal waste treatment. The current baseline for solidification of the secondary wastes is a cement-based waste form. However, alternative secondary waste forms are being considered. In this regard, Ceramicrete technology, developed at Argonne National Laboratory, is being explored as an option to solidify and stabilize the secondary wastes. The Ceramicrete process has been demonstrated on four secondary waste formulations: baseline, cluster 1, cluster 2, and mixed waste streams. Based on the recipes provided by Pacific Northwest National Laboratory, the four waste simulants were prepared in-house. Waste forms were fabricated with three filler materials: Class C fly ash, CaSiO{sub 3}, and Class C fly ash + slag. Optimum waste loadings were as high as 20 wt.% for the fly ash and CaSiO{sub 3}, and 15 wt.% for fly ash + slag filler. Waste forms for physical characterizations were fabricated with no additives, hazardous contaminants, and radionuclide surrogates. Physical property characterizations (density, compressive strength, and 90-day water immersion test) showed that the waste forms were stable and durable. Compressive strengths were >2,500 psi, and the strengths remained high after the 90-day water immersion test. Fly ash and CaSiO{sub 3} filler waste forms appeared to be superior to the waste forms with fly ash + slag as a filler. Waste form weight loss was {approx}5-14 wt.% over the 90-day immersion test. The majority of the weight loss occurred during the initial phase of the immersion test, indicative of washing off of residual unreacted

Observations in the statistical analysis of NBG-18 nuclear graphite strength tests

International Nuclear Information System (INIS)

Hindley, Michael P.; Mitchell, Mark N.; Blaine, Deborah C.; Groenwold, Albert A.

2012-01-01

Highlights: ► Statistical analysis of NBG-18 nuclear graphite strength test. ► A Weibull distribution and normal distribution is tested for all data. ► A Bimodal distribution in the CS data is confirmed. ► The CS data set has the lowest variance. ► A Combined data set is formed and has Weibull distribution. - Abstract: The purpose of this paper is to report on the selection of a statistical distribution chosen to represent the experimental material strength of NBG-18 nuclear graphite. Three large sets of samples were tested during the material characterisation of the Pebble Bed Modular Reactor and Core Structure Ceramics materials. These sets of samples are tensile strength, flexural strength and compressive strength (CS) measurements. A relevant statistical fit is determined and the goodness of fit is also evaluated for each data set. The data sets are also normalised for ease of comparison, and combined into one representative data set. The validity of this approach is demonstrated. A second failure mode distribution is found on the CS test data. Identifying this failure mode supports the similar observations made in the past. The success of fitting the Weibull distribution through the normalised data sets allows us to improve the basis for the estimates of the variability. This could also imply that the variability on the graphite strength for the different strength measures is based on the same flaw distribution and thus a property of the material.

Waste form development and characterization in pyrometallurgical treatment of spent nuclear fuel

International Nuclear Information System (INIS)

Ackerman, J.

1998-01-01

Electrometallurgical treatment is a compact, inexpensive method that is being developed at Argonne National Laboratory to deal with spent nuclear fuel, primarily metallic and oxide fuels. In this method, metallic nuclear fuel constituents are electrorefined in a molten salt to separate uranium from the rest of the spent fuel. Oxide and other fuels are subjected to appropriate head end steps to convert them to metallic form prior to electrorefining. The treatment process generates two kinds of high-level waste--a metallic and a ceramic waste. Isolation of these wastes has been developed as an integral part of the process. The wastes arise directly from the electrorefiner, and waste streams do not contain large quantities of solvent or other process fluids. Consequently, waste volumes are small and waste isolation processes can be compact and rapid. This paper briefly summarizes waste isolation processes then describes development and characterization of the two waste forms in more detail

Stress Tests Worldwide - IAEA Nuclear Safety Action Plan

International Nuclear Information System (INIS)

Lyons, J.E.

2012-01-01

The IAEA nuclear safety action plan relies on 11 important issues. 1) Safety assessments in light of the Fukushima accident: the IAEA secretariat will develop a methodology for stress tests against specific extreme natural hazards and will provide assistance for their implementation; 2) Strengthen existing IAEA peer reviews; 3) Emergency preparedness and response; 4) National Regulatory bodies in terms of independence and adequacy of human and financial resources; 5) The development of safety culture and scientific and technical capacity in Operating Organizations; 6) The upgrading of IAEA safety standards in a more efficient way; 7) A better implementation of relevant conventions concerning nuclear safety and nuclear accidents; 8) To provide a broad assistance on safety standard for countries embarking on a nuclear power program; 9) To facilitate the use of available information, expertise and techniques concerning radiation protection; 10) To enhance the transparency of nuclear industry; and 11) To promote the cooperation between member states in nuclear safety. (A.C.)

Production of metal waste forms from spent fuel treatment

International Nuclear Information System (INIS)

Westphal, B.R.; Keiser, D.D.; Rigg, R.H.; Laug, D.V.

1995-01-01

Treatment of spent nuclear fuel at Argonne National Laboratory consists of a pyroprocessing scheme in which the development of suitable waste forms is being advanced. Of the two waste forms being proposed, metal and mineral, the production of the metal waste form utilizes induction melting to stabilize the waste product. Alloying of metallic nuclear materials by induction melting has long been an Argonne strength and thus, the transition to metallic waste processing seems compatible. A test program is being initiated to coalesce the production of the metal waste forms with current induction melting capabilities

Penetration Testing Model for Web sites Hosted in Nuclear Malaysia

International Nuclear Information System (INIS)

Mohd Dzul Aiman Aslan; Mohamad Safuan Sulaiman; Siti Nurbahyah Hamdan; Saaidi Ismail; Mohd Fauzi Haris; Norzalina Nasiruddin; Raja Murzaferi Mokhtar

2012-01-01

Nuclear Malaysia web sites has been very crucial in providing important and useful information and services to the clients as well as the users worldwide. Furthermore, a web site is important as it reflects the organisation image. To ensure the integrity of the content of web site, a study has been made and a penetration testing model has been implemented to test the security of several web sites hosted at Nuclear Malaysia for malicious attempts. This study will explain how the security was tested in the detailed condition and measured. The result determined the security level and the vulnerability of several web sites. This result is important for improving and hardening the security of web sites in Nuclear Malaysia. (author)

Guidelines for inservice testing at nuclear power plants

International Nuclear Information System (INIS)

Campbell, P.

1995-04-01

The staff of the U.S. Nuclear Regulatory Commission (NRC) gives licensees guidelines and recommendations for developing and implementing programs for the inservice testing of pumps and valves at commercial nuclear power plants. The staff discusses the regulations; the components to be included in an inservice testing program; and the preparation and content of cold shutdown justifications, refueling outage justifications, and requests for relief from the American Society of Mechanical Engineers Code requirements. The staff also gives specific guidance on relief acceptable to the NRC and advises licensees in the use of this information at their facilities. The staff discusses the revised standard technical specifications for the inservice testing program requirements and gives guidance on the process a licensee may follow upon finding an instance of noncompliance with the Code

Characteristics of radionuclide contamination of different zones of Semipalatinsk Nuclear Test Site ``Opytnoe pole''

Science.gov (United States)

Kadyrzhanov, K. K.; Khazhekber, S.; Lukashenko, S. N.; Solodukhin, V. P.; Kazachevskiy, I. V.; Poznyak, V. L.; Knyazev, B. B.; Rofer, Ch.

2003-01-01

Data on the spatial distribution of radionuclides (241Am, 239Pu, 137Cs and 152Eu) formed during nuclear explosions of different types near P2 SNTS test site are presented. Radionuclide contamination induced by the explosions varies in the concentrations of individual radionuclides, their proportions and species. Examination of the variations is a crucial task to plan remediation activities as well as those aimed at decrease of radiation risk for population and prevention of repeated contamination. Concentrations of 241Am and 239+240Pu that are the most toxic radionuclides in the area lie in hundred thousands of Bqkg-1. The most contaminated areas are classified by the radionuclide concentration, ratio and form present in soil.

Research and test facilities required in nuclear science and technology

International Nuclear Information System (INIS)

2009-01-01

Experimental facilities are essential research tools both for the development of nuclear science and technology and for testing systems and materials which are currently being used or will be used in the future. As a result of economic pressures and the closure of older facilities, there are concerns that the ability to undertake the research necessary to maintain and to develop nuclear science and technology may be in jeopardy. An NEA expert group with representation from ten member countries, the International Atomic Energy Agency and the European Commission has reviewed the status of those research and test facilities of interest to the NEA Nuclear Science Committee. They include facilities relating to nuclear data measurement, reactor development, neutron scattering, neutron radiography, accelerator-driven systems, transmutation, nuclear fuel, materials, safety, radiochemistry, partitioning and nuclear process heat for hydrogen production. This report contains the expert group's detailed assessment of the current status of these nuclear research facilities and makes recommendations on how future developments in the field can be secured through the provision of high-quality, modern facilities. It also describes the online database which has been established by the expert group which includes more than 700 facilities. (authors)

Technology, safety, and costs of decommissioning reference nuclear research and test reactors. Main report

International Nuclear Information System (INIS)

Konzek, G.J.; Ludwick, J.D.; Kennedy, W.E. Jr.; Smith, R.I.

1982-03-01

Safety and Cost Information is developed for the conceptual decommissioning of two representative licensed nuclear research and test reactors. Three decommissioning alternatives are studied to obtain comparisons between costs (in 1981 dollars), occupational radiation doses, potential radiation dose to the public, and other safety impacts. The alternatives considered are: DECON (immediate decontamination), SAFSTOR (safe storage followed by deferred decontamination), and ENTOMB (entombment). The study results are presented in two volumes. Volume 1 (Main Report) contains the results in summary form

Testing waste forms containing high radionuclide loadings

International Nuclear Information System (INIS)

McConnell, J.W. Jr.; Neilson, R.M. Jr.; Rogers, R.D.

1986-01-01

The Low-Level Waste Data Base Development - EPICOR-II Resin/Liner Investigation Program funded by the US Nuclear Regulatory Commission (NRC) is obtaining information on radioactive waste during NRC-prescribed tests and in a disposal environment. This paper describes the resin solidification task of that program, including the present status and results to date. An unusual aspect of this investigation is the use of commercial grade, ion exchange resins that have been loaded with over five times the radioactivity normally seen in a commercial application. That dramatically increases the total radiation dose to the resins. The objective of the resin solidification task is to determine the adequacy of test procedures specified by NRC for ion exchange resins having high radionuclide loadings

The resumption-stopping of nuclear tests: between fear and hope

International Nuclear Information System (INIS)

Gillis, B.

1996-01-01

The situation of French deterrence, with the resumption of nuclear weapons tests until the nuclear explosions simulation with the mega joules laser and the PALEN programme, is described here. (N.C.). 1 map

Workshop on the leaching mechanisms of nuclear-waste forms, October 27-28, 1981. Summary report

International Nuclear Information System (INIS)

Mendel, J.E.

1982-04-01

The purpose of this informal workshop was to initiate the program and achieve the following goals: (1) acquaint laboratory investigators (data generators) with the needs of the mathematical modelers (data users). Session I was devoted to a tutorial by D.D. Jackson, mathematical modeler for the leaching mechanisms program, on PROTOCOL, a general case waste form leaching model; (2) define important testing parameters, based on the present state of knowledge. To achieve this, a number of important testing parameters were identified for special discussion in Session II; (3) develop an understanding of the interrelationships between the activities of leaching mechanisms program participants, and begin definition of the specific role of each participant in the overall program; and (4) establish good communication between the leaching mechanisms program and related programs, particularly the waste form leaching program at the Savannah River Laboratory (SRL) and the various Nuclear Waste Terminal Storage (NWTS) waste package programs. The agenda for the workshop is attached as Appendix A; a list of attendees is in Appendix B. Because this workshop was devoted to preliminary planning for the leaching mechanisms program, the presentations and discussions were purposely kept informal. This report represents a synopsis of the proceedings that has been prepared by the leaching mechanisms coordinator and reviewed by the workshop participants

Hitlers' bomb. The secret story of Germanys' nuclear weapon tests

International Nuclear Information System (INIS)

Karlsch, R.

2005-01-01

This book reveals a sensation: Under supervision of the SS German scientists tested 1944/45 nuclear bombs on Ruegen and in Thuringia. During this period several hundred prisoners of war and prisoners died. Besides proofs for nuclear weapon testing the author also found a draft for a patent on plutonium bombs and discovered the first functioning German atom reactor in the environs of Berlin. (GL) [de

Ongoing research experiments at the former Soviet nuclear test site in eastern Kazakhstan

Science.gov (United States)

Leith, William S.; Kluchko, Luke J.; Konovalov, Vladimir; Vouille, Gerard

2002-01-01

Degelen mountain, located in EasternKazakhstan near the city of Semipalatinsk, was once the Soviets most active underground nuclear test site. Two hundred fifteen nuclear tests were conducted in 181 tunnels driven horizontally into its many ridges--almost twice the number of tests as at any other Soviet underground nuclear test site. It was also the site of the first Soviet underground nuclear test--a 1-kiloton device detonated on October 11, 1961. Until recently, the details of testing at Degelen were kept secret and have been the subject of considerable speculation. However, in 1991, the Semipalatinsk test site became part of the newly independent Republic of Kazakhstan; and in 1995, the Kazakhstani government concluded an agreement with the U.S. Department of Defense to eliminate the nuclear testing infrastructure in Kazakhstan. This agreement, which calls for the "demilitarization of the infrastructure directly associated with the nuclear weapons test tunnels," has been implemented as the "Degelen Mountain Tunnel Closure Program." The U.S. Defense Threat Reduction Agency, in partnership with the Department of Energy, has permitted the use of the tunnel closure project at the former nuclear test site as a foundation on which to support cost-effective, research-and-development-funded experiments. These experiments are principally designed to improve U.S. capabilities to monitor and verify the Comprehensive Test Ban Treaty (CTBT), but have provided a new source of information on the effects of nuclear and chemical explosions on hard, fractured rock environments. These new data extends and confirms the results of recent Russian publications on the rock environment at the site and the mechanical effects of large-scale chemical and nuclear testing. In 1998, a large-scale tunnel closure experiment, Omega-1, was conducted in Tunnel 214 at Degelen mountain. In this experiment, a 100-ton chemical explosive blast was used to test technologies for monitoring the

Around Semipalatinsk nuclear test site: Progress of dose estimations relevant to the consequences of nuclear tests

International Nuclear Information System (INIS)

Stepanenko, Valeriy F.; Hoshi, Masaharu; Bailiff, Ian K.

2006-01-01

by RLD and calculations. A possible explanation of the differences between ESR and RLD/calculations doses is the following: for interpretation of ESR data the shielding and behaviour' factors for investigated persons should be taken into account. The 'upper level' of the combination of 'shielding and behaviour' factors of dose reduction for inhabitants of Dolon' village of about 0.28 was obtained by comparing the individual ESR tooth enamel dose estimates with the calculated mean dose for this settlement. The biological dosimetry data related to the settlements near SNTS were presented at the Workshop. A higher incidence of unstable chromosome aberrations, micronucleus in lymphocytes, nuclear abnormalities of thyroid follicular cells, T-cell receptor mutations in peripheral blood were found for exposed areas (Dolan', Sarjal) in comparison with unexposed ones (Kokpekty). The significant greater frequency of stable translocations (results of analyses of chromosome aberrations in lymphocytes by the FISH technique) was demonstrated for Dolon' village in comparison with Chekoman (unexposed village). The elevated level of stable translocations in Dolon' corresponds to a dose of about 180 mSv, which is close to the results of ESR dosimetry for this village. The importance of investigating specific morphological types of thyroid nodules for dosimetry studies was pointed out. In general the 3rd Dosimetry Workshop has demonstrated remarkable progress in developing an international level of common approaches for retrospective dose estimations around the SNTS and in understanding the tasks for the future joint work in this direction. In the framework of a special session the problems of developing a database and registry in order to support epidemiological studies around SNTS were discussed. The results of investigation of psychological consequences of nuclear tests, which are expressed in the form of verbal behaviour, were presented at this session as well. (author)

Task force for integral test of High Energy nuclear data

Energy Technology Data Exchange (ETDEWEB)

Oyama, Yukio [Japan Atomic Energy Research Inst., Tokai, Ibaraki (Japan). Tokai Research Establishment

1998-11-01

According to completion of the JENDL-High Energy file for neutron nuclear cross sections up to 50 MeV, a task force for integral test of high energy nuclear data was organized to discuss a guide line for integral test activities. A status of existing differential and integral experiments and how to perform such a test were discussed in the task force. Here the purpose and outline of the task force is explained with some future problems raised in discussion among the task member. (author)

Cold crucible induction melter test for crystalline ceramic waste form fabrication: A feasibility assessment

Energy Technology Data Exchange (ETDEWEB)

Amoroso, Jake W., E-mail: jake.amoroso@srnl.doe.gov [Savannah River National Laboratory, Aiken, SC 29808 (United States); Marra, James; Dandeneau, Christopher S. [Savannah River National Laboratory, Aiken, SC 29808 (United States); Brinkman, Kyle; Xu, Yun [Clemson University, Clemson, SC 29634 (United States); Tang, Ming [Los Alamos National Laboratory, Los Alamos, NM 87545 (United States); Maio, Vince [Idaho National Laboratory, Idaho Falls, ID 83415 (United States); Webb, Samuel M. [Stanford Synchrotron Radiation Lightsource, SLAC National Accelerator Laboratory, Menlo Park, CA 94086 (United States); Chiu, Wilson K.S. [University of Connecticut, Storrs, Connecticut 06269-3139 (United States)

2017-04-01

The first scaled proof-of-principle cold crucible induction melter (CCIM) test to process a multiphase ceramic waste form from a simulated combined (Cs/Sr, lanthanide and transition metal fission products) commercial used nuclear fuel waste stream was recently conducted in the United States. X-ray diffraction, 2-D X-ray absorption near edge structure (XANES), electron microscopy, inductively coupled plasma-atomic emission spectroscopy (and inductively coupled plasma-mass spectroscopy for Cs), and product consistency tests were used to characterize the fabricated CCIM material. Characterization analyses confirmed that a crystalline ceramic with a desirable phase assemblage was produced from a melt using a CCIM. Primary hollandite, pyrochlore/zirconolite, and perovskite phases were identified in addition to minor phases rich in Fe, Al, or Cs. The material produced in the CCIM was chemically homogeneous and displayed a uniform phase assemblage with acceptable aqueous chemical durability.

Tests with ceramic waste form materials made by pressureless consolidation

International Nuclear Information System (INIS)

Lewis, M. A.; Hash, M. C.; Hebden, A. S.; Ebert, W. L.

2002-01-01

A multiphase waste form referred to as the ceramic waste form (CWF) will be used to immobilize radioactively contaminated salt wastes recovered after the electrometallurgical treatment of spent sodium-bonded nuclear fuel. The CWF is made by first occluding salt in zeolite and then encapsulating the zeolite in a borosilicate binder glass. A variety of surrogate CWF materials were made using pressureless consolidation (PC) methods for comparison with CWF consolidated using a hot isostatic press (HIP) method and to study the effects of glass/zeolite batching ratio and processing conditions on the physical and chemical properties of the resulting materials. The data summarized in this report will also be used to support qualification of the PC CWF for disposal in the proposed federal high-level radioactive waste repository at Yucca Mountain. The phase composition and microstructure of HIP CWF and PC CWF are essentially identical: both are composed of about 70% sodalite, 25% binder glass, and a 5% total of inclusion phases (halite, nepheline, and various oxides and silicates). The primary difference is that PC CWF materials have higher porosities than HIP CWFs. The product consistency test (PCT) that was initially developed to monitor homogeneous glass waste forms was used to measure the chemical durabilities of the CWF materials. Series of replicate tests with several PC CWF materials indicate that the PCT can be conducted with the same precision with CWF materials as with borosilicate glasses. Short-term (7-day) PCTs were used to evaluate the repeatability of making the PC CWF and the effects of the glass/zeolite mass ratio, process temperature, and processing time on the chemical durability. Long-term (up to 1 year) PCTs were used to compare the durabilities of HIP and PC CWFs and to estimate the apparent solubility limit for the PC CWF that is needed for modeling. The PC and HIP CWF materials had similar disabilities, based on the release of silicon in long

General discrimination technique to determine between earthquake and nuclear test with seismic data

International Nuclear Information System (INIS)

Bashillah Baharuddin; Alawiah Musa; Roslan Mohd Ali

2007-01-01

The Comprehensive Nuclear-Test-Ban Treaty (CTBT) was developed to ban of any nuclear weapon test explosion moreover will restrict the development and qualitative improvement of nuclear weapons and end the development of advanced new types of these weapons. The Treaty provides for a comprehensive global verification regime, which includes an International Monitoring System (IMS). The IMS comprises a network of 321 monitoring stations and 16 radionuclide laboratories that monitor the Earth for evidence of nuclear explosions, which cover underground, underwater and atmosphere environments. Presently, Malaysia receives seismic, infrasound, hydroacoustic and radionuclide data from the International Data Centre (IDC) of the CTBT. In order to maximise the use of the data for the purposes of the CTBT, the Malaysian Nuclear Agency is developing capability to analyse the data in order to detect nuclear weapon test, with an initial focus on the seismic data. Through the CTBT IMS, seismic data is constantly being obtained to monitor and detect nuclear explosions. However, in the process, other natural and man-made activities that generate seismic waves, especially earthquakes and large man-made explosions, are also detectable through the IMS, and need to be differentiated and discriminated before any nuclear explosions can be identified. The detection capability by using seismological methods was proven through simulated explosion tests at selected nuclear weapon test sites. This is supported by data previously collected from a total of 2089 nuclear weapon tests that have been carried out globally, out of which 1567 were underground, 514 in the atmosphere, including outer space, and 8 underwater. The discrimination of seismic data to detect nuclear explosions from natural earthquake and explosions can be undertaken through the identification of the epicentre location, hypocentre depth, magnitude and short-period discrimination of the seismic events. (Author)

Kazakhstan without nuclear potential

International Nuclear Information System (INIS)

Abishev, M.A.; Iskakova, G.A.

2000-01-01

Kazakhstan have great heritage of the USSR military industry in form of test sites and scientific and technological complexes of different kind of weapons developments. The Republic of Kazakstan possesses of most large number of nuclear sites per head of the population. Developed industry of mining, processing of uranium ores demands solution of radioactive wastes handling problems. Therefore regime of non-proliferation and defense conversion are strategic priorities of state policy. For Kazakhstan ideals of non-proliferation of mass destruction weapon have particular meaning. Consequences of nuclear weapon tests of territory of Kazakhstan reflected on population health and on ecological balance of the region. Wide public support helps forms policy in sphere of non-proliferation of nuclear weapon. Kazakhstan executes obligations of Lisbon Protocol and consolidates the frameworks of strategic security

Radioiodine (131I) in animal thyroids during nuclear tests in both hemispheres

International Nuclear Information System (INIS)

Van Middlesworth, L.

1975-01-01

In mid-1974 a small increase of 131 I was observed in animal thyroids following a nuclear test in China. In late 1974 there was no public announcement of an atmospheric nuclear test in the Northern Hemisphere, but 131 I was readily measured in animal thyroids. This latter increase occurred while animals in the Southern Hemisphere accumulated 131 I from nuclear tests in the Southern Hemisphere. It is suggested that in late 1974 the Northern Hemisphere was contaminated by either late fallout from tests in June or by interhemispheric mixing or by a combination of these sources. (author)

Explosively free-formed pass partition plate for a nuclear steam generator

International Nuclear Information System (INIS)

Schroeder, J.W.

1980-01-01

A large flow-separating dished plate of a complex shape was manufactured by near-contact explosive forming in which only an edge die was used. The shape of the part, for service in a large, nuclear steam generator, was obtained by careful sizing and placement of the explosive charge. The development of the technique and the manufacture of the plate are described. 4 refs

Thermoluminescence dosimetry of gamma rays from the fallout of the Semipalatinsk nuclear tests

International Nuclear Information System (INIS)

Takada, J.; Hoshi, M.; Endo, S.; Yamamoto, M.; Nagatomo, T.; Gusev, B.I.; Rozenson, R.I.; Apsalikov, K.N.; Tchaijunusova, N.J.

1996-01-01

Field missions were sent to several settlements near the Semipalatinsk nuclear test site out in order to investigate dosimetry for the residents in 1995. The results of measurements of environmental radiation doses and thermoluminescence dosimetry in some villages near the Semipalatinsk nuclear test site are presented. The radiation levels in several villages are the natural background level in 1995, 6 years after the final nuclear explosion. On the other hand, thermoluminescence dosimetry revealed significant radiation exposure to residents in this area due to nuclear tests. (author)

SP-100 nuclear assembly test: Test assembly functional requirements and system arrangement

International Nuclear Information System (INIS)

Fallas, T.T.; Gluck, R.; Motwani, K.; Clay, H.; O'Neill, G.

1991-01-01

This paper describes the functional requirements and the system that will be tested to validate the reactor, flight shield, and flight controller of the SP-100 Generic Flight System (GFS). The Nuclear Assembly Test (NAT) consists of the test article (SP-100 reactor with control devices and the flight shield) and its supporting systems. The NAT test assembly is being designed by GE. Westinghouse Hanford Company (WHC) is designing the test cell and vacuum vessel system that will contain the NAT test assembly (Renkey et al. 1989). Preliminary design reviews have been completed and the final design is under way

Ceramic nuclear waste forms. II. A ceramic-waste composite prepared by hot pressing. Progress report and preprint

International Nuclear Information System (INIS)

McCarthy, G.J.

1975-01-01

A feasibility study was conducted to determine whether nuclear waste calcine and a crystalline ceramic matrix can be fabricated by hot pressing into a composite waste form with suitable leaching resistance and thermal stability. It was found that a hard, dense composite could be formed using the typical commercial waste formulation PW-4b and a matrix of α-quartz with a small amount of a lead borosilicate glass added as a consolidation aide. Its density, waste loading, and leaching resistance are comparable to the glasses currently being considered for fixation of nuclear wastes. The hot pressed composite offers a closer approach to thermodynamic stability and improved thermal stability (in monolithic form) compared to glass waste forms. Recommendations for further optimization of the hot pressed waste form are given. (U.S.)

Test of GEANT3 and GEANT4 nuclear models for 160 MeV protons stopping in CH2

International Nuclear Information System (INIS)

Paganetti, H.; Gottschalk, B.

2003-01-01

Monte Carlo simulations are used for many problems in proton radiation therapy, some of which are sensitive to the nuclear interaction model. The available models have been little tested in the regime of interest, namely in their ability to predict the secondary particle yield, including their angle and energy, when 70-250 MeV protons stop in various materials. The present study provides one such test in carbon, complementing a previous one in copper. Using a multilayer Faraday cup we have measured the projected range distribution of charged nuclear secondaries from 160 MeV protons stopping in polyethylene (CH 2 ). To test the popular GEANT Monte Carlo we have simulated the experiment with GEANT3 using the 'Gheisha' (default) and 'Fluka' models and with GEANT4.5 using the 'low-energy' and 'precompound' models. The GEANT3/Fluka and GEANT4/precompound simulations agree moderately well with the observed range distribution. The data are given in a convenient form for testing other Monte Carlo programs

Nuclear tests of lepton number and CP nonconservation

International Nuclear Information System (INIS)

Haxton, W.C.

1984-01-01

I will discuss two topics, double beta decay and time-reversal-odd nuclear moments, in which important questions of nuclear structure must be addressed. These problems are taken from a growing class of nuclear and atomic experiments in which the special properties of many-body systems are exploited to test properties of elementary particles. Nuclei can serve as filters for interactions by providing kinematic windows where only certain processes can occur and by isolating quantum numbers such as spin, isospin, and parity. In addition, the strengths of interesting interactions can be enhanced through the mixing of nearly degenerate levels in nuclei. However, the most important asset of nuclear and atomic experiments is their precision. For example, experiments searching for T-odd nuclear moments exploit techniques for measuring changes in atomic energies of 10 -22 eV. Such precision techniques will play an increasingly important role in particle physics. In the discussion of double beta decay and T-odd nuclear moments it will become clear that important nuclear structure issues must be resolved in order to fully exploit the experimental results. During this talk I will highlight this aspect. 29 references

Irradiation test on connector part for nuclear instrumentation of nuclear powered ship 'Mutsu'

International Nuclear Information System (INIS)

Kudo, Takahiro; Mizushima, Toshihiko; Tsunoda, Tsunemi; Nakazawa, Toshio

1991-01-01

The nuclear instrumetnation facility of the nuclear powered ship 'Mutsu' is composed of neutron detectors, signal cables and the circuits for measurement, and ocntinuously monitors neutron flux. Since this facility treats very faint signals, for the signal cables, coaxial cables and triple coaxial cables are used. The coaxial cables for the nuclear instrumentation are equipped with connectors at both ends, and those are called prefabricated cable. The prefabricated cables are connected to neutron detectors, and installed in the detection holes of the primary shielding tank in the containment vessel. Therefore, at the time of reactor operation, they are exposed to high radiation, and the deterioration of the characteristics of the prefabricated cables is feared. For the purpose of confirming that the part of deteriorating the insulation of the prefabricated cables is connectors, and clarifying the cause of the deterioration of insulation in connector part, the irradiation test of this time was carried out. The environment in which the prefabricated cables are laid, the specifications of the cables and connectors, the materials, gamma ray irradiation and the test results are reported. (K.I.)

Evolution of 99Tc Species in Cementitious Nuclear Waste Form

International Nuclear Information System (INIS)

Um, Woo Yong; Westsik, Joseph H.

2011-01-01

Technetium (Tc) is produced in large quantities as a fission product during the irradiation of 235 U-enriched fuel for commercial power production and plutonium genesis for nuclear weapons. The most abundant isotope of Tc present in the wastes is 99 Tc because of its high fission yield (∼6%) and long half-life (2.13x10 5 years). During the Cold War era, generation of fissile 239 Pu for use in America's atomic weapons arsenal yielded nearly 1900 kg of 99 Tc at the U.S. Department of Energy's (DOE) Hanford Site in southeastern Washington State. Most of this 99 Tc is present in fuel reprocessing wastes temporarily stored in underground tanks awaiting retrieval and permanent disposal. After the wastes are retrieved from the storage tanks, the bulk of the high-level waste (HLW) and lowactivity waste (LAW) stream is scheduled to be converted into a borosilicate glass waste form that will be disposed of in a shallow burial facility called the Integrated Disposal Facility (IDF) at the Hanford Site. Even with careful engineering controls, volatilization of a fraction of Tc during the vitrification of both radioactive waste streams is expected. Although this volatilized Tc can be captured in melter off-gas scrubbers and returned to the melter, some of the Tc is expected to become part of the secondary waste stream from the vitrification process. The off-gas scrubbers downstream from the melters will generate a high pH, sodium-ammonium carbonate solution containing the volatilized Tc and other fugitive species. Effective and cost-efficient disposal of Tc found in the off-gas scrubber solution remains difficult. A cementitious waste form (Cast Stone) is one of the nuclear waste form candidates being considered to solidify the secondary radioactive liquid waste that will be generated by the operation of the waste treatment plant (WTP) at the Hanford Site. Because Tc leachability from the waste form is closely related with Tc speciation or oxidation state in both the simulant

Chemical Explosion Experiments to Improve Nuclear Test Monitoring - Developing a New Paradigm for Nuclear Test Monitoring with the Source Physics Experiments (SPE)

International Nuclear Information System (INIS)

Snelson, Catherine M.; Abbott, Robert E.; Broome, Scott T.; Mellors, Robert J.; Patton, Howard J.; Sussman, Aviva J.; Townsend, Margaret J.; Walter, William R.

2013-01-01

A series of chemical explosions, called the Source Physics Experiments (SPE), is being conducted under the auspices of the U.S. Department of Energy's National Nuclear Security Administration (NNSA) to develop a new more physics-based paradigm for nuclear test monitoring. Currently, monitoring relies on semi-empirical models to discriminate explosions from earthquakes and to estimate key parameters such as yield. While these models have been highly successful monitoring established test sites, there is concern that future tests could occur in media and at scale depths of burial outside of our empirical experience. This is highlighted by North Korean tests, which exhibit poor performance of a reliable discriminant, mb:Ms (Selby et al., 2012), possibly due to source emplacement and differences in seismic responses for nascent and established test sites. The goal of SPE is to replace these semi-empirical relationships with numerical techniques grounded in a physical basis and thus applicable to any geologic setting or depth

Development of TIG Welding System for a Nuclear Fuel Test Rig

Energy Technology Data Exchange (ETDEWEB)

Joung, Changyoung; Ahn, Sungho; Hong, Jintae; Kim, Kahye [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

2013-05-15

The welding process is one of the most important among the instrumentation processes of the nuclear fuel test rig and rods. To manufacture the nuclear fuel test rig, a precision welding system needs to be fabricated to develop various welding technologies of the fuel test rig and rods jointing the various sensors and end caps on a fuel cladding tube, which is charged with fuel pellets and component parts. Thus, we designed and fabricated the precision welding system consisting of an orbital TIG welder, a low-pressure chamber, and a high-pressure chamber. Using this system, the performance tests were performed with the round and seal spot welds for each welding condition. This paper describes not only the contents for the fabrication of precision TIG welding system but also some results from weld tests using the low-pressure and high-pressure chambers to verify the performance of this system. The TIG welding system was developed to manufacture the nuclear fuel test rig and rods. It has been configured to be able to weld the nuclear fuel test rigs and rods by applying the TIG welder using a low-pressure chamber and a high-pressure chamber. The performance tests using this system were performed with the round and seal spot welds for the welding conditions. The soundness of the orbital TIG welding system was confirmed through performance tests in the low-pressure and high-pressure chambers.

Development of TIG Welding System for a Nuclear Fuel Test Rig

International Nuclear Information System (INIS)

Joung, Changyoung; Ahn, Sungho; Hong, Jintae; Kim, Kahye

2013-01-01

The welding process is one of the most important among the instrumentation processes of the nuclear fuel test rig and rods. To manufacture the nuclear fuel test rig, a precision welding system needs to be fabricated to develop various welding technologies of the fuel test rig and rods jointing the various sensors and end caps on a fuel cladding tube, which is charged with fuel pellets and component parts. Thus, we designed and fabricated the precision welding system consisting of an orbital TIG welder, a low-pressure chamber, and a high-pressure chamber. Using this system, the performance tests were performed with the round and seal spot welds for each welding condition. This paper describes not only the contents for the fabrication of precision TIG welding system but also some results from weld tests using the low-pressure and high-pressure chambers to verify the performance of this system. The TIG welding system was developed to manufacture the nuclear fuel test rig and rods. It has been configured to be able to weld the nuclear fuel test rigs and rods by applying the TIG welder using a low-pressure chamber and a high-pressure chamber. The performance tests using this system were performed with the round and seal spot welds for the welding conditions. The soundness of the orbital TIG welding system was confirmed through performance tests in the low-pressure and high-pressure chambers

Impact test for solid waste forms

International Nuclear Information System (INIS)

Wallace, R.M.; Kelley, J.A.

1976-03-01

Samples of concretes and glasses being considered for incorporation of radioactive waste sludge were subjected to impact tests to determine the relationship between the energy of the impact and the resulting increase in surface area of the damaged sample. Test results indicate that the increased surface area per unit of energy input for glass waste forms is less by a factor of about three than that for concretes containing 40 wt percent simulated sludge (average values of 9.6 cm 2 /Joule and 24.7 cm 2 /Joule for glass and concrete, respectively)

DPRK's 4{sup th} Nuclear Test and its Tritium Production

Energy Technology Data Exchange (ETDEWEB)

Kim, Min Soo; Lee, Sang Joon; Chang, Sun Young [Korea Institute of Nuclear Nonproliferation and Control, Daejeon (Korea, Republic of)

2016-05-15

On January 6, 2016 at 10:30am, the artificial earthquake in the DPRK was detected by multiple international seismic organizations. After 2 hours, the DPRK announced on state TV that 'The first H-bomb test was successfully conducted in the DPRK at 10:00 am on Wednesday, Juche 105(2016), pursuant to the strategic determination of the ruling communist party.' There has been a doubt about the real nature of the DPRK's 4th nuclear test, since 2 months have been passed after its nuclear test. To analyze the nature of the DPRK's nuclear test, it is necessary to check possible options for production of essential materials. The pathways to produce nuclear fusion material (tritium) and to have a relatively high possibility for the DPRK are described in this article. Tritium is key material for H-bomb. And there are two options for the DPRK which are 1) production and 2) illicit trafficking. And this study is focused on production possibility of DPRK. Determination of the nature of DPRK's nuclear test is very hard issue.

Nuclear start-up, testing and core management of the Fast Test Reactor (FTR)

International Nuclear Information System (INIS)

Bennett, R.A.; Daughtry, J.W.; Harris, R.A.; Jones, D.H.; Nelson, J.V.; Rawlins, J.A.; Rothrock, R.B.; Sevenich, R.A.; Zimmerman, B.D.

1980-01-01

Plans for the nuclear start-up, low and high power physics testing, and core management of the Fast Test Reactor (FTR) are described. Owing to the arrangement of the fuel-handling system, which permits continuous instrument lead access to experiments during refuelling, it is most efficient to load the reactor in an asymmetric fashion, filling one-third core sectors at a time. The core neutron level will be monitored during this process using both in-core and ex-core detectors. A variety of physics tests are planned following the core loading. Because of the experimental purpose of the reactor, these tests will include a comprehensive characterization programme involving both active and passive neutron and gamma measurements. Following start-up tests, the FTR will be operated as a fast neutron irradiation facility, to test a wide variety of fast reactor core components and materials. Nuclear analyses will be made prior to each irradiation cycle to confirm that the planned arrangement of standard and experimental components satisfies all safety and operational constraints, and that all experiments are located so as to achieve their desired irradiation environment. (author)

Nondestructive testing of nuclear reactor components integrity

International Nuclear Information System (INIS)

Mala, M.; Miklos, M.

2011-01-01

Nuclear energy must respond to current challenges in the energy market. The significant parameters are increase of the nuclear fuel price, closed fuel cycle, reduction and safe and the final disposal of high level radioactive waste. Nowadays, the discussions on suitable energy mix are taking place not only here in Czech Republic, but also in many other European countries. It is necessary to establish an appropriate ratio among the production of electricity from conventional, nuclear and renewable energy sources. Also, it is necessary to find ways how to streamline the economy, central part of the nuclear fuel cycle and thereby to increase the competitiveness of nuclear energy. This streamlining can be carried out by improving utilization of existing nuclear fuel with maintaining a high degree of nuclear facilities safety. Increasing operational reliability and safety together with increasing utilization of nuclear fuel place increasing demands on monitoring of changes during fuel burnup. The potential fuel assembly damages in light water reactors are prevented by the introduction of new procedures and programs of the fuel assembly monitoring. One of them is the Post Irradiation Inspection Program (PIIP) which is a good tool for monitoring of chemical regime impact on the fuel assembly cladding behavior. Main nondestructive techniques that are used at nuclear power plants for the fuel assembly integrity evaluation are ultrasonic measurements, eddy current measurements, radiographic testing, acoustic techniques and others. Ultrasonic system is usual tool for leak fuel rod evaluation and it is also used at Temelin NPP. Since 2009, Temelin NPP has cooperated with Research Center Rez Ltd in frame of PIIP program at both units WWER 1000. This program was established for US VVantage6 fuel assemblies and also it continues for Russian TVSA-T fuel assemblies. (author)

Testing techniques in nuclear, petroleum and metallurgic industries

International Nuclear Information System (INIS)

Anon.

1977-01-01

The nondestructive testing techniques by ultrasonic waves, eddy currents, acoustic emission used by Intercontrole (a CEA's affiliated firm in nuclear petrochemical, and engineering site measurements) are presented [fr

Benchmarking of direct and indirect friction tests in micro forming

DEFF Research Database (Denmark)

Eriksen, Rasmus Solmer; Calaon, Matteo; Arentoft, M.

2012-01-01

The sizeable increase in metal forming friction at micro scale, due to the existence of size effects, constitutes a barrier to the realization of industrial micro forming processes. In the quest for improved frictional conditions in micro scale forming operations, friction tests are applied...... to qualify the tribological performance of the particular forming scenario. In this work the application of a simulative sliding friction test at micro scale is studied. The test setup makes it possible to measure the coefficient of friction as a function of the sliding motion. The results confirm a sizeable...... increase in the coefficient of friction when the work piece size is scaled down. © (2012) Trans Tech Publications....

Two CANDU fueling machines tested at the Institute For Nuclear Research - Pitesti

International Nuclear Information System (INIS)

Doca, Cezar; Cojocaru, Virgil

2005-01-01

In 2003, as a national and European premiere, at the Institute for Nuclear Research Pitesti (INR), the Fueling Machine Head no.4 (F/M) for the Nuclear Power Plant Cernavoda - Unit 2 was successfully tested. In 2005, a second Fueling Machine (no.5) was tested for the Nuclear Power Plant Cernavoda - Unit 2. The Institute's main objective is to develop scientific and technological support for the Romanian Nuclear Power Program. Testing the Fueling Machines at INR Pitesti is part of the overall program to assimilate in Romania the CANDU technology. To perform the tests of these machines at INR Pitesti, a special testing rig was built and is available for this goal. Both the testing rig and staff had successfully assessed by the AECL representatives during two missions. There was a delivery contract between GEC Canada and Nuclear Power Plant Cernavoda - Unit 2 to provide the Fueling Machines no. 4 and no. 5 in Romania before testing operation. As a first conclusion, the Institute for Nuclear Research Pitesti has the facilities, the staff and the experience to perform possible co-operations with any other CANDU Reactor owner. This experience will support the next steps concerning F/M commissioning in the NPP Cernavoda - Unit 2 and also give the confidence to the end-users that the Institute's team can provide technical assistance during the operation. Also, the obtained results demonstrate that the overall refurbishment of the F/M control system in Unit 1 and Unit 2 will be possible. The paper presents: - a short description of the F/M head;- a short description of the F/M test rig; - the computer control system; - the F/M testing activities; -results and expectations. (authors)

Two CANDU fueling machines tested at the Institute For Nuclear Research - Pitesti

International Nuclear Information System (INIS)

Doca, C.; Cojocaru, V.

2005-01-01

Full text: In 2003, as a national and European premiere, at the Institute for Nuclear Research Pitesti (INR), the Fueling Machine Head no.4 (F/M) for the Nuclear Power Plant Cernavoda - Unit 2 was successfully tested. In 2005, a second Fueling Machine (no.5) was tested for the Nuclear Power Plant Cernavoda - Unit 2. The Institute's main objective is to develop scientific and technological support for the Romanian Nuclear Power Program. Testing the Fueling Machines at INR Pitesti is part of the overall program to assimilate in Romania the CANDU technology. To perform the tests of these machines at INR Pitesti, a special testing rig was built and is available for this goal. Both the testing rig and staff had successfully assessed by the AECL representatives during two missions. There was a delivery contract between GEC Canada and Nuclear Power Plant Cernavoda - Unit 2 to provide the Fueling Machines no. 4 and no. 5 in Romania before testing operation. As a first conclusion, the Institute for Nuclear Research Pitesti has the facilities, the staff and the experience to perform possible co-operations with any other CANDU Reactor owner. This experience will support the next steps concerning F/M commissioning in the NPP Cernavoda - Unit 2 and also give the confidence to the end-users that the Institute's team can provide technical assistance during the operation. Also, the obtained results demonstrate that the overall refurbishment of the F/M control system in Unit 1 and Unit 2 will be possible. The paper presents: - a short description of the F/M head;- a short description of the F/M test rig; - the computer control system; - the F/M testing activities; -results and expectations. (authors)

Effects of container material on PCT leach test results for high-level nuclear waste glasses

International Nuclear Information System (INIS)

Xing, S.B.; Pegg, I.L.

1994-01-01

A glass-based waste form used for the immobilization of high-level nuclear wastes should exhibit good resistance to aqueous corrosion since typically this is the primary process by which radionucleides could be released into the environment upon failure of other barriers. In the USA, the Waste Acceptance Product Specifications (WAPS) provides a set of requirements to ensure the consistency of the waste forms produced and specifies the Product Consistency Test (PCT) as a measure of relative chemical durability. While the PCT procedure permits usage of both Teflon and stainless steel vessels for testing of simulated development glasses, Teflon is not permitted for testing of production glasses due to radiative degradation. The results presented in this paper indicate that there are very significant differences between tests conducted in the two types of vessels due to the well-known permeability of Teflon to atmospheric carbon dioxide which results in lowering of the solution pH and a consequent reduction in the leach rate of silicate glasses. A wide range of nuclear waste glass compositions was subjected to the PCT procedure using both Teflon and stainless steel vessels. The magnitude of the effect (up to a factor of four for B, Na, Li concentrations) depends strongly on glass composition, therefore the isolated checks performed previously were inconclusive. The permeability to CO, of two types of Teflon vessels specified in the PCT procedure was directly measured using buffer solutions: ingress of CO, is linear in time, strongly pH-dependent, and was as high as 100 ppm after 7 days. In actual PCT tests in Teflon vessels, the total CO, content was 560 ppm after 87 days and 1930 ppm after one year

Pyrochlore as nuclear waste form. Actinide uptake and chemical stability

International Nuclear Information System (INIS)

Finkeldei, Sarah Charlotte

2015-01-01

Radioactive waste is generated by many different technical and scientific applications. For the past decades, different waste disposal strategies have been considered. Several questions on the waste disposal strategy remain unanswered, particularly regarding the long-term radiotoxicity of minor actinides (Am, Cm, Np), plutonium and uranium. These radionuclides mainly arise from high level nuclear waste (HLW), specific waste streams or dismantled nuclear weapons. Although many countries have opted for the direct disposal of spent fuel, from a scientific and technical point of view it is imperative to pursue alternative waste management strategies. Apart from the vitrification, especially for trivalent actinides and Pu, crystalline ceramic waste forms are considered. In contrast to glasses, crystalline waste forms, which are chemically and physically highly stable, allow the retention of radionuclides on well-defined lattice positions within the crystal structure. Besides polyphase ceramics such as SYNROC, single phase ceramics are considered as tailor made host phases to embed a specific radionuclide or a specific group. Among oxidic single phase ceramics pyrochlores are known to have a high potential for this application. This work examines ZrO 2 based pyrochlores as potential nuclear waste forms, which are known to show a high aqueous stability and a high tolerance towards radiation damage. This work contributes to (1) understand the phase stability field of pyrochlore and consequences of non-stoichiometry which leads to pyrochlores with mixed cationic sites. Mixed cationic occupancies are likely to occur in actinide-bearing pyrochlores. (2) The structural uptake of radionuclides themselves was studied. (3) The chemical stability and the effect of phase transition from pyrochlore to defect fluorite were probed. This phase transition is important, as it is the result of radiation damage in ZrO 2 based pyrochlores. ZrO 2 - Nd 2 O 3 pellets with pyrochlore and defect

Critical Review of EU Nuclear Stress Tests in Bulgaria, Hungary, Romania and Ukraine

International Nuclear Information System (INIS)

Becker, O.; Lorenz, P.; Wallner, A.

2012-01-01

In March 2011, the core melt accidents at the Fukushima Daiichi 1 nuclear power plant (NPP) showed the world that the nuclear industry cannot prevent severe accidents from happening. The accidents in Japan proved that highly unlikely accidents cannot be excluded. The Fukushima accident confirmed the mistrust towards nuclear power among the Japanese but also European citizens. In reaction to the devastating nuclear disaster in Japan the European Council concluded in March 2011, that the safety of all EU nuclear plants should be reviewed on the basis of a comprehensive and transparent risk and safety assessment ('stress tests'). The EU Nuclear Safety Regulators Group – ENSREG took over the task to provide a “targeted reassessment of the safety margins of nuclear power plants”, thus examining whether the safety margins which were used in the licensing of NPPs are sufficient to cover unexpected events. It is important to understand that the stress tests could not take into account all key safety issues such as the capability to prevent accidents - the scope of the stress tests defined by ENSREG didn´t promise to deliver a comprehensive risk and safety assessment. According to some observers the stress tests were mainly set up to improve the confidence in the safety of European NPPs. Nevertheless, the stress tests provided some interesting findings concerning safety: This study assesses the safety of the nuclear power plants in Bulgaria, Hungary, Romania and the Ukraine. The introduction contains an overview of the content and procedure of the stress tests. This “Critical Review of the Stress Tests” is based on the national stress tests reports written by the national nuclear safety authorities and on the Peer review country reports attached to the Peer review report - Stress tests performed on European nuclear power plants written by the Peer review Teams, the Peer Review Board respectively, and endorsed by ENSREG [ENSREG 2012a, ENSREG 2012c]. It

Critical Review of EU Nuclear Stress Tests in Bulgaria, Hungary, Romania and Ukraine

Energy Technology Data Exchange (ETDEWEB)

Becker, O.; Lorenz, P.; Wallner, A.

2012-07-01

In March 2011, the core melt accidents at the Fukushima Daiichi 1 nuclear power plant (NPP) showed the world that the nuclear industry cannot prevent severe accidents from happening. The accidents in Japan proved that highly unlikely accidents cannot be excluded. The Fukushima accident confirmed the mistrust towards nuclear power among the Japanese but also European citizens. In reaction to the devastating nuclear disaster in Japan the European Council concluded in March 2011, that the safety of all EU nuclear plants should be reviewed on the basis of a comprehensive and transparent risk and safety assessment ('stress tests'). The EU Nuclear Safety Regulators Group – ENSREG took over the task to provide a “targeted reassessment of the safety margins of nuclear power plants”, thus examining whether the safety margins which were used in the licensing of NPPs are sufficient to cover unexpected events. It is important to understand that the stress tests could not take into account all key safety issues such as the capability to prevent accidents - the scope of the stress tests defined by ENSREG didn´t promise to deliver a comprehensive risk and safety assessment. According to some observers the stress tests were mainly set up to improve the confidence in the safety of European NPPs. Nevertheless, the stress tests provided some interesting findings concerning safety: This study assesses the safety of the nuclear power plants in Bulgaria, Hungary, Romania and the Ukraine. The introduction contains an overview of the content and procedure of the stress tests. This “Critical Review of the Stress Tests” is based on the national stress tests reports written by the national nuclear safety authorities and on the Peer review country reports attached to the Peer review report - Stress tests performed on European nuclear power plants written by the Peer review Teams, the Peer Review Board respectively, and endorsed by ENSREG [ENSREG 2012a, ENSREG 2012c]. It continues

Dynamic testing of nuclear power plant structures: an evaluation

International Nuclear Information System (INIS)

Weaver, H.J.

1980-02-01

Lawrence Livermore Laboratory (LLL) evaluated the applications of system identification techniques to the dynamic testing of nuclear power plant structures and subsystems. These experimental techniques involve exciting a structure and measuring, digitizing, and processing the time-history motions that result. The data can be compared to parameters calculated using finite element or other models of the test systems to validate the model and to verify the seismic analysis. This report summarizes work in three main areas: (1) analytical qualification of a set of computer programs developed at LLL to extract model parameters from the time histories; (2) examination of the feasibility of safely exciting nuclear power plant structures and accurately recording the resulting time-history motions; (3) study of how the model parameters that are extracted from the data be used best to evaluate structural integrity and analyze nuclear power plants

Study on the seismic monitoring system development against the adjacent countries nuclear test

International Nuclear Information System (INIS)

Min, Kyung Sik; Ahn, Jong Sung; Lee, Jong Wook; Chang, In Soon; Seo, In Seok; Kwak, Eun Ho

1995-12-01

The project was carried out to construct foundation for the monitoring of the neighboring countries's nuclear test by seismic method. For this, we collected, organized and analyzed the information about the Comparative Test Ban Treaty (CTBT) and investigated theoretical backgrounds of the elastic wave generation by the Nuclear test and the identification of the nuclear tests from the natural earthquakes. And the computer system was setup to obtain realtime data from the broadband seismograph in Inchon of the Korean Meteorological Agency. 15 refs. (Author)

Nuclear weapon testing and the monkey business

International Nuclear Information System (INIS)

Murthy, M.S.S.

1978-01-01

Reasons for India's total ban on the export of rhesus monkeys to U.S. have been explained. The major reason is that some of the animals were used in nuclear weapon related radiation experiments. This was a clear violation of a stricture in the agreement about supply of monkeys. The stricture prohibited the use of animals for research concerning military operations, including nuclear weapon testing. It is pleaded that a strict enforcement of strictures rather than a total ban on the export of monkeys would be better in the interest of advancement of knowledge in human medicine and disease control. (M.G.B.)

Nuclear test watchers feel political heat

International Nuclear Information System (INIS)

Marshall, E.

1987-01-01

One year after US citizen diplomats signed a remarkable pact with the Soviet Union to monitor nuclear bomb tests, they are running into some of the obstacles that regular diplomats encounter - political flak from the Pentagon and harassment by the Soviet military. But they have devised some technical solutions that they hope will get them around the roadblocks. These solutions are discussed

Forming Limit Diagrams of Zircaloy-4 and Zirlo Sheets for Stamping of Spacer Grids of Nuclear Fuel Rods

International Nuclear Information System (INIS)

Seo, Yun Mi; Hyun, Hong Chul; Lee, Hyung Yil; Kim, Nak Soo

2011-01-01

In this work, we investigated the theoretical forming limit models for Zircaloy-4 and Zirlo used for spacer grid of nuclear fuel rods. Tensile and anisotropy tests were performed to obtain stress-strain curves and anisotropic coefficients. The experimental forming limit diagrams (FLD) for two materials were obtained by dome stretching tests following NUMISHEET 96. Theoretical FLD depends on FL models and yield criteria. To obtain the right hand side (RHS) of FLD, we applied the FL models (Swift's diffuse necking, M-K theory, S-R vertex theory) to Zircaloy-4 and Zirlo sheets. Hill's local necking theory was adopted for the left hand side (LHS) of FLD. To consider the anisotropy of sheets, the yield criteria of Hill and Hosford were applied. Comparing the predicted curves with the experimental data, we found that the RHS of FLD for Zircaloy-4 can be described by the Swift model (with the Hill's criterion), while the LHS of the FLD can be explained by Hill model. The FLD for Zirlo can be explained by the S-R model and the Hosford's criterion (a = 8)

Seismological analysis of the fourth North Korean nuclear test

Science.gov (United States)

Hartmann, Gernot; Gestermann, Nicolai; Ceranna, Lars

2016-04-01

The Democratic People's Republic of Korea has conducted its fourth underground nuclear explosions on 06.01.2016 at 01:30 (UTC). The explosion was clearly detected and located by the seismic network of the International Monitoring System (IMS) of the Comprehensive Nuclear-Test-Ban Treaty (CTBT). Additional seismic stations of international earthquake monitoring networks at regional distances, which are not part of the IMS, are used to precisely estimate the epicenter of the event in the North Hamgyong province (41.38°N / 129.05°E). It is located in the area of the North Korean Punggye-ri nuclear test site, where the verified nuclear tests from 2006, 2009, and 2013 were conducted as well. The analysis of the recorded seismic signals provides the evidence, that the event was originated by an explosive source. The amplitudes as well as the spectral characteristics of the signals were examined. Furthermore, the similarity of the signals with those from the three former nuclear tests suggests very similar source type. The seismograms at the 8,200 km distant IMS station GERES in Germany, for example, show the same P phase signal for all four explosions, differing in the amplitude only. The comparison of the measured amplitudes results in the increasing magnitude with the chronology of the explosions from 2006 (mb 4.2), 2009 (mb 4.8) until 2013 (mb 5.1), whereas the explosion in 2016 had approximately the same magnitude as that one three years before. Derived from the magnitude, a yield of 14 kt TNT equivalents was estimated for both explosions in 2013 and 2016; in 2006 and 2009 yields were 0.7 kt and 5.4 kt, respectively. However, a large inherent uncertainty for these values has to be taken into account. The estimation of the absolute yield of the explosions depends very much on the local geological situation and the degree of decoupling of the explosive from the surrounding rock. Due to the missing corresponding information, reliable magnitude-yield estimation for the

Zirconium sponge and other forms of virgin metal for nuclear applications - approved standard 1973

International Nuclear Information System (INIS)

Anon.

1975-01-01

This specification covers virgin zirconium metal commonly designated as sponge because of its porous, sponge-like texture, but it may also take other forms such as chunklets. One grade is described which is designated as reactor grade R-1, suitable for use in nuclear applications. The most important characteristic of the reactor grade is its low nuclear cross section as achieved by removal of hafnium and careful quality control in manufacturing procedures to prevent contamination with other high cross section materials

Nuclear anxiety: a test-construction study

International Nuclear Information System (INIS)

Braunstein, A.L.

1986-01-01

The Nuclear Anxiety Scale was administered to 263 undergraduate and graduate studies (on eight occasions in December, 1985 and January, 1986). (1) The obtained alpha coefficient was .91. This was significant at the .01 level, and demonstrated that the scale was internally homogeneous and consistent. (2) Item discrimination indices (point biserial correlation coefficients) computered for the thirty (30) items yielded a range of .25 to .64. All coefficients were significant at the .01 level, and all 30 items were retained as demonstrating significant discriminability. (3) The correlation between two administrations of the scale (with a 48-hour interval) was .83. This was significant at the .01 level, and demonstrated test-retest reliability and stability over time. (4) The point-biserial correlation coefficient between scores on the Nuclear Anxiety Scale, and the students' self-report of nuclear anxiety as being either a high or low ranked stressor, was .59. This was significant at the .01 level, and demonstrated concurrent validity. (5) The correlation coefficient between scores on the Nuclear Anxiety Scale and the Spielberger State-Trait Anxiety Inventory, A-Trait, (1970), was .41. This was significant at the .01 level, and demonstrated convergent validity. (6) The correlation coefficient between positively stated and negatively stated items (with scoring reversed) was .76. This was significant at the .01 level, and demonstrated freedom from response set bias

Evaluation of the radionuclide tracer test conducted at the project Gnome Underground Nuclear Test Site, New Mexico

International Nuclear Information System (INIS)

Pohll, G.; Pohlmann, K.

1996-08-01

A radionuclide tracer test was conducted in 1963 by the U.S. Geological Survey at the Project Gnome underground nuclear test site, approximately 40 km southeast of Carlsbad, New Mexico. The tracer study was carried out under the auspices of the U.S. Atomic Energy Commission (AEC) to study the transport behavior of radionuclides in fractured rock aquifers. The Culebra Dolomite was chosen for the test because it was considered to be a reasonable analogue of the fractured carbonate aquifer at the Nevada Test Site (NTS), the principal location of U.S. underground nuclear tests. Project Gnome was one of a small number of underground nuclear tests conducted by the AEC at sites distant from the NTS. The Gnome device was detonated on December 10, 1961 in an evaporate unit at a depth of 360 m below ground surface. Recently, the U.S. Department of Energy (DOE) implemented an environmental restoration program to characterize, remediate, and close these offsite nuclear test areas. An early step in this process is performance of a preliminary risk analysis of the hazard posed by each site. The Desert Research Institute has performed preliminary hydrologic risk evaluations for the groundwater transport pathway at Gnome. That evaluation included the radioactive tracer test as a possible source because the test introduced radionuclides directly into the Culebra Dolomite, which is the only aquifer at the site. This report presents a preliminary evaluation of the radionuclide tracer test as a source for radionuclide migration in the Culebra Dolomite. The results of this study will assist in planning site characterization activities and refining estimates of the radionuclide source for comprehensive models of groundwater transport st the Gnome site

Development of fracture toughness test method for nuclear grade graphite

Energy Technology Data Exchange (ETDEWEB)

Chang, C. H.; Lee, J. S.; Cho, H. C.; Kim, D. J.; Lee, D. J. [Korea Advanced Institute of Science and Technology, Daejeon (Korea, Republic of)

2006-02-15

Because of its high strength and stability at very high temperature, as well as very low thermal neutron absorption cross-section, graphite has been widely used as a structural material in Gas Cooled Reactors (GCR). Recently, many countries are developing the Very High Temperature gas cooled Reactor (VHTR) because of the potentials of hydrogen production, as well as its safety and viable economics. In VHTR, helium gas serves as the primary coolant. Graphite will be used as a reflector, moderator and core structural materials. The life time of graphite is determined from dimensional changes due to neutron irradiation, which closely relates to the changes of crystal structure. The changes of both lattice parameter and crystallite size can be easily measured by X-ray diffraction method. However, due to high cost and long time of neutron irradiation test, ion irradiation test is being performed instead in KAERI. Therefore, it is essential to develop the technique for measurement of ion irradiation damage of nuclear graphite. Fracture toughness of nuclear grade graphite is one of the key properties in the design and development of VHTR. It is important not only to evaluate the various properties of candidate graphite but also to assess the integrity of nuclear grade graphite during operation. Although fracture toughness tests on graphite have been performed in many laboratories, there have been wide variations in values of the calculated fracture toughness, due to the differences in the geometry of specimens and test conditions. Hence, standard test method for nuclear graphite is required to obtain the reliable fracture toughness values. Crack growth behavior of nuclear grade graphite shows rising R-curve which means the increase in crack growth resistance as the crack length increases. Crack bridging and microcracking have been proposed to be the dominant mechanisms of rising R-curve behavior. In this paper, the technique to measure the changes of crystallite size and

Reviews of the Comprehensive Nuclear-Test-Ban Treaty and U.S. security

Science.gov (United States)

Jeanloz, Raymond

2017-11-01

Reviews of the Comprehensive Nuclear-Test-Ban Treaty (CTBT) by the National Academy of Sciences concluded that the United States has the technical expertise and physical means to i) maintain a safe, secure and reliable nuclear-weapons stockpile without nuclear-explosion testing, and ii) effectively monitor global compliance once the Treaty enters into force. Moreover, the CTBT is judged to help constrain proliferation of nuclear-weapons technology, so it is considered favorable to U.S. security. Review of developments since the studies were published, in 2002 and 2012, show that the study conclusions remain valid and that technical capabilities are better than anticipated.

Recognition structure of semipalatinsk residents caused by nuclear explosion tests

International Nuclear Information System (INIS)

Hirabayashi, Kyoko; Satoh, Kenichi; Ohtaki, Megu; Muldagaliyev, T.; Apsalikov, K.; Kawano, Noriyuki

2012-01-01

Authors' team of Hiroshima University and Scientific Research Institute of Radiation Medicine and Ecology (Kazakhstan) has been investigating the health state, exposure route, contents and mental effect of nuclear explosion tests of Semipalatinsk residents through their witness and questionnaire since 2002, to elucidate the humanistic damage of nuclear tests. Reported here is the recognition structure in the title statistically analyzed with use of frequently spoken words in the witness. The audit was performed in 2002-2007 to 994 residents who had experienced ground explosion tests during the period from 1949 to 1962 and were living in 26 villages near the old test site. Asked questions concerning nuclear tests involved such items as still unforgettable matters, dreadful events, regretting things, thought about the test, requests; and matters about themselves, their family, close friends and anything. The frequency of the test site-related words heard in the interview were analyzed with hierarchical clustering and multi-dimensional scaling with a statistic software R for computation and MeCab for morphological analysis. Residents' recognition was found to be of two structures of memory at explosion tests and anger/dissatisfaction/anxiety to the present state. The former contained the frequent words of mushroom cloud, flash, blast, ground tremble and outdoor evacuation, and the latter, mostly anxiety about health of themselves and family. Thus residents have had to be confronted with uneasiness of their health even 20 years after the closure of the test site. (T.T.)

Alternative Forms of the Rey Auditory Verbal Learning Test: A Review

Directory of Open Access Journals (Sweden)

Keith A. Hawkins

2004-01-01

Full Text Available Practice effects in memory testing complicate the interpretation of score changes over repeated testings, particularly in clinical applications. Consequently, several alternative forms of the Auditory Verbal Learning Test (AVLT have been developed. Studies of these typically indicate that the forms examined are equivalent. However, the implication that the forms in the literature are interchangeable must be tempered by several caveats. Few studies of equivalence have been undertaken; most are restricted to the comparison of single pairs of forms, and the pairings vary across studies. These limitations are exacerbated by the minimal overlapping across studies in variables reported, or in the analyses of equivalence undertaken. The data generated by these studies are nonetheless valuable, as significant practice effects result from serial use of the same form. The available data on alternative AVLT forms are summarized, and recommendations regarding form development and the determination of form equivalence are offered.

The former tests realized to a personal neutron dosemeter based on solid nuclear tracks detector

International Nuclear Information System (INIS)

Camacho, M.E.; Tavera, L.; Balcazar, M.

1997-01-01

Due to the increase in the use of neutron radiation a personal neutron dosemeter based on solid nuclear tracks detector (DSTN) was designed and constructed. The personal dosemeter design consists of three arrangements. The first one consists of a plastic nuclear tracks detector (LR115 or CR39) in contact with a LiF pellet. The second one is the same that above but it placed among two cadmium pellets and, the third one is formed by the alone detector without converter neither neutron absorber. The three arrangements are placed inside a plastic porta detector hermetically closed to avoid the bottom produced by environmental radon whichever both detectors (LR115 and CR39) are sensitive. In this work the former tests realized to that dosemeter are presented. (Author)

The advanced test reactor national scientific user facility advancing nuclear technology

International Nuclear Information System (INIS)

Allen, T.R.; Thelen, M.C.; Meyer, M.K.; Marshall, F.M.; Foster, J.; Benson, J.B.

2009-01-01

projects and faculty/staff exchanges. In June of 2008, the first week-long ATR NSUF Summer Session was attended by 68 students, university faculty and industry representatives. The Summer Session featured presentations by 19 technical experts from across the country and covered topics including irradiation damage mechanisms, degradation of reactor materials, LWR and gas reactor fuels, and non-destructive evaluation. High impact research results from leveraging the entire research infrastructure, including universities, industry, small business, and the national laboratories. To increase overall research capability, ATR NSUF seeks to form strategic partnerships with university facilities that add significant nuclear research capability to the ATR NSUF and are accessible to all ATR NSUF users. Current partner facilities include the MIT Reactor, the University of Michigan Irradiated Materials Testing Laboratory, the University of Wisconsin Characterization Laboratory, and the University of Nevada, Las Vegas Transmission Electron Microscope User Facility. Needs for irradiation of material specimens at tightly controlled temperatures are being met by dedication of a large in-pile pressurized water loop facility for use by ATR NSUF users. Several environmental mechanical testing systems are under construction to determine crack growth rates and fracture toughness on irradiated test systems. These state-of-the-art capabilities, combined with a recent DOE investment in post-irradiation analytical equipment including a shielded Electron Probe MicroAnalyzer, a dual beam Focused Ion Beam, x-ray micro-diffraction, and scanning laser thermal diffusivity measurement will increase ATR-NSUF cutting-edge research capabilities for future users. (author)

Radiological effluents released from nuclear rocket and ramjet engine tests at the Nevada Test Site 1959 through 1969: Fact Book

Energy Technology Data Exchange (ETDEWEB)

Friesen, H.N.

1995-06-01

Nuclear rocket and ramjet engine tests were conducted on the Nevada Test Site (NTS) in Area 25 and Area 26, about 80 miles northwest of Las Vegas, Nevada, from July 1959 through September 1969. This document presents a brief history of the nuclear rocket engine tests, information on the off-site radiological monitoring, and descriptions of the tests.

Test and evaluation of computerized nuclear material accounting methods. Final report

International Nuclear Information System (INIS)

1995-01-01

In accordance with the definition of a Material Balance Area (MBA) as a well-defined geographical area involving an Integral operation, the building housing the BFS-1 and BFS-1 critical facilities is considered to consist of one MBA. The BFS materials are in the form of small disks clad in stainless steel and each disk with nuclear material has its own serial number. Fissile material disks in the BFS MBA can be located at three key monitoring points: BFS-1 facility, BFS-2 facility and main storage of BFS fissile materials (storage 1). When used in the BFS-1 or BFS-2 critical facilities, the fissile material disks are loaded in tubes (fuel rods) forming critical assembly cores. The following specific features of the BFS MBA should be taken into account for the purpose of computerized accounting of nuclear material: (1) very large number of nuclear material items (about 70,000 fissile material items); and (2) periodically very intensive shuffling of nuclear material items. Requirements for the computerized system are determined by basic objectives of nuclear material accounting: (1) providing accurate information on the identity and location of all items in the BFS material balance area; (2) providing accurate information on location and identity of tamper-indicating devices; (3) tracking nuclear material inventories; (4) issuing periodic reports; (5) assisting with the detection of material gains or losses; (6) providing a history of nuclear material transactions; (7) preventing unauthorized access to the system and data falsification. In August 1995, the prototype computerized accounting system was installed on the BFS facility for trial operation. Information on two nuclear material types was entered into the data base: weapon-grade plutonium metal and 36% enriched uranium dioxide. The total number of the weapon-grade plutonium disks is 12,690 and the total number of the uranium dioxide disks is 1,700

Nuclear test - The French nuclear strike force in the 21. century: challenges, ambitions and strategy

International Nuclear Information System (INIS)

Wodka-Gallien, Philippe

2014-01-01

This bibliographical note presents a book in which the author, after having recalled the history of the French nuclear force since the first nuclear test in 1960, and outlined the fact that France has been living under the protection of its own nuclear deterrence force since that date, presents the components of this nuclear strike force with its four nuclear submarines equipped to launch new generation missiles, its fifty fighter bomber aircraft equipped with the ASMP-A missile. He presents and discusses the mission of this nuclear force, discusses the relevancy of the deterrence strategy in the present context, and the significance of such a strategy for a European country like France. He wanders whether this strike force is still affordable for our country, which can be its benefits, whether this arsenal remains useful as it has been designed in the Cold War context. He also discusses the disarmament perspectives in an unsteady international environment where power and arms race logics prevail again

HTTR demonstration test plan for industrial utilization of nuclear heat

International Nuclear Information System (INIS)

Sato, Hiroyuki; Ohashi, Hirofumi; Yan, Xing L.; Kubo, Shinji; Nishihara, Tetsuo; Tachibana, Yukio; Inagaki, Yoshiyuki

2014-09-01

Japan Atomic Energy Agency has been conducting research and development with a central focus on the utilization of High Temperature engineering Test Reactor (HTTR), the first High Temperature Gas-cooled Reactor (HTGR) in Japan, towards the realization of industrial use of nuclear heat. Several studies have made on the integration of the HTTR with thermochemical iodine-sulfur process and steam methane reforming hydrogen production plant (H 2 plant) as well as helium gas turbine power conversion system. In addition, safety standards for coupling a H 2 plant to a nuclear facility has been investigated. Based on the past design information, the present study identified test items to be validated in the HTTR demonstration test to accomplish a formulation of safety requirement and design consideration for coupling a H 2 plant to a nuclear facility as well as confirmation of overall performance of helium gas turbine system. In addition, plant concepts for the heat utilization system to be connected with the HTTR are investigated. (author)

Radiation damage studies related to nuclear waste forms

International Nuclear Information System (INIS)

Gray, W.J.; Wald, J.W.; Turcotte, R.P.

1981-12-01

Much of the previously reported work on alpha radiation effects on crystalline phases of importance to nuclear waste forms has been derived from radiation effects studies of composite waste forms. In the present work, two single-phase crystalline materials, Gd 2 Ti 2 O 7 (pyrochlore) and CaZrTi 2 O 7 (zirconolite), of relative importance to current waste forms were studied independently by doping with 244 Cm at the 3 wt % level. Changes in the crystalline structure measured by x-ray diffraction as a function of dose show that damage ingrowth follows an expected exponential relationship of the form ΔV/V 0 = A[1-exp(-BD)]. In both cases, the materials became x-ray amorphous before the estimated saturation value was reached. The predicted magnitudes of the unit cell volume changes at saturation are 5.4% and 3.5%, respectively, for Gd 2 Ti 2 O 7 and CaZrTi 2 O 7 . The later material exhibited anisotropic behavior in which the expansion of the monoclinic cell in the c 0 direction was over five times that of the a 0 direction. The effects of transmutations on the properties of high-level waste solids have not been studied until now because of the long half-lives of the important fission products. This problem was circumvented in the present study by preparing materials containing natural cesium and then irradiating them with neutrons to produce 134 Cs, which has only a 2y half-life. The properties monitored at about one year intervals following irradiation have been density, leach rate and microstructure. A small amount of x-ray diffraction work has also been done. Small changes in density and leach rate have been observed for some of the materials, but they were not large enough to be of any consequence for the final disposal of high level wastes

Characterization and durability testing of a glass-bonded ceramic waste form

International Nuclear Information System (INIS)

Johnson, S. G.

1998-01-01

Argonne National Laboratory is developing a glass bonded ceramic waste form for encapsulating the fission products and transuranics from the conditioning of metallic reactor fuel. This waste form is currently being scaled to the multi-kilogram size for encapsulation of actual high level waste. This paper will present characterization and durability testing of the ceramic waste form. An emphasis on results from application of glass durability tests such as the Product Consistency Test and characterization methods such as X-ray diffraction and scanning electron microscopy. The information presented is based on a suite of tests utilized for assessing product quality during scale-up and parametric testing

Handling effluent from nuclear thermal propulsion system ground tests

International Nuclear Information System (INIS)

Shipers, L.R.; Allen, G.C.

1992-01-01

A variety of approaches for handling effluent from nuclear thermal propulsion system ground tests in an environmentally acceptable manner are discussed. The functional requirements of effluent treatment are defined and concept options are presented within the framework of these requirements. System concepts differ primarily in the choice of fission-product retention and waste handling concepts. The concept options considered range from closed cycle (venting the exhaust to a closed volume or recirculating the hydrogen in a closed loop) to open cycle (real time processing and venting of the effluent). This paper reviews the different methods to handle effluent from nuclear thermal propulsion system ground tests

Simulation of Valve Operation for Flow Interrupt Test in Nuclear Power Plant

International Nuclear Information System (INIS)

Kim, Jae Hyung; Shin, Dae Yong; Shin, Dong Woo; Kim, Charn Jung; Lee, Jung Hee

2012-01-01

The valve used in nuclear power plant must be qualified for the function according to the KEPIC MF. The test valve must be selected by shape and size, which is given by KEPIC MF. In the functional test, the mathematical model for the valve operation is needed. The mathematical model must be verified by the test, whose method and procedure is defined in KEPIC MF. The lack of analytical technique has lead to the poor mathematical model, with which the functional test for the big valve is impossible with analytical method. Especially, the tank and rupture disk in the flow test is not considered and the result of the analysis is so different to the real one. In these days, the 3D model for the flow interrupt test makes more accurate analysis. And no facility about functional test reduces the research will for the nuclear power plant valve. For this problem, the test facility for the functional test of the valve and pump in nuclear power plant has been made until 2012. With the test facility, the research project related the valve were initiated in KIMM( Korea Institute of Machinery and Materials). And the joint project to SNU(Seoul National University) has been going on the numerical analysis for the valve in nuclear power plant. Using the commercial software and user subroutine, UDF, the co-simulation with multi-body dynamic and fluid flow analysis and the addition of tank and rupture disk to the user subroutine make possible to simulate the flow interrupt test numerically. This is not simple and regular analysis, which was introduced in user subroutine. In order to simulate the real situation, the engineering work, related mathematical model, and the programming in the user subroutine are needed. This study is on the making the mathematical model for the functional test of the valve in nuclear power plan. The functional test is the real test procedure and defined in KEPIC MF

A Science-Based Approach to Understanding Waste Form Durability in Open and Closed Nuclear Fuel Cycles

International Nuclear Information System (INIS)

Peters, M.T.; Ewing, R.C.

2007-01-01

There are two compelling reasons for understanding source term and near-field processes in a radioactive waste geologic repository. First, almost all of the radioactivity is initially in the waste form, mainly in the spent nuclear fuel (SNF) or nuclear waste glass. Second, over long periods, after the engineered barriers are degraded, the waste form is a primary control on the release of radioactivity. Thus, it is essential to know the physical and chemical state of the waste form after hundreds of thousands of years. The United States Department of Energy's Yucca Mountain Repository Program has initiated a long-term program to develop a basic understanding of the fundamental mechanisms of radionuclide release and a quantification of the release as repository conditions evolve over time. Specifically, the research program addresses four critical areas: a) SNF dissolution mechanisms and rates; b) formation and properties of U 6+ - secondary phases; c) waste form-waste package interactions in the near-field; and d) integration of in-package chemical and physical processes. The ultimate goal is to integrate the scientific results into a larger scale model of source term and near-field processes. This integrated model will be used to provide a basis for understanding the behavior of the source term over long time periods (greater than 10 5 years). Such a fundamental and integrated experimental and modeling approach to source term processes can also be readily applied to development of advanced waste forms as part of a closed nuclear fuel cycle. Specifically, a fundamental understanding of candidate waste form materials stability in high temperature/high radiation environments and near-field geochemical/hydrologic processes could enable development of advanced waste forms 'tailored' to specific geologic settings. (authors)

A Science-Based Approach to Understanding Waste Form Durability in Open and Closed Nuclear Fuel Cycles

International Nuclear Information System (INIS)

M.T. Peters; R.C. Ewing

2006-01-01

There are two compelling reasons for understanding source term and near-field processes in a radioactive waste geologic repository. First, almost all of the radioactivity is initially in the waste form, mainly in the spent nuclear fuel (SNF) or nuclear waste glass. Second, over long periods, after the engineered barriers are degraded, the waste form is a primary control on the release of radioactivity. Thus, it is essential to know the physical and chemical state of the waste form after hundreds of thousands of years. The United States Department of Energy's Yucca Mountain Repository Program has initiated a long-term program to develop a basic understanding of the fundamental mechanisms of radionuclide release and a quantification of the release as repository conditions evolve over time. Specifically, the research program addresses four critical areas: (a) SNF dissolution mechanisms and rates; (b) formation and properties of U 6+ -secondary phases; (c) waste form-waste package interactions in the near-field; and (d) integration of in-package chemical and physical processes. The ultimate goal is to integrate the scientific results into a larger scale model of source term and near-field processes. This integrated model will be used to provide a basis for understanding the behavior of the source term over long time periods (greater than 10 5 years). Such a fundamental and integrated experimental and modeling approach to source term processes can also be readily applied to development of advanced waste forms as part of a closed nuclear fuel cycle. Specifically, a fundamental understanding of candidate waste form materials stability in high temperature/high radiation environments and near-field geochemical/hydrologic processes could enable development of advanced waste forms ''tailored'' to specific geologic settings

Using tritium as an indicator for development effective radionuclide methods for identification of nuclear testing venues

Energy Technology Data Exchange (ETDEWEB)

Lyakhova, O.; Lukashenko, S.; Larionova, N.; Timonova, L. [Institute of radiation safety and ecology (Kazakhstan)

2014-07-01

scene of the explosion, is a few and tens of Bq/m3. In particular, the tritium content in the atmosphere near the one of the boreholes was 70 Bq/m{sup 3}. Research of level and distribution of tritium in the different object of ecosystems within the nuclear test venues has also been done. In accordance with results the tritium content in water was about 1.10{sup 5} Bq/l, in the air was up to 1 400 Bq/m{sup 3}, in vegetation - up to 1.10{sup 6} Bq/l, in the snow cover was about 500 Bq/kg, in soil - up to 50 000 Bq/kg. Based on all of the data will be held on the selection of the most effective elements of the ecosystem, which could be used as an indicator of nuclear test. Studies have shown the fundamental possibility of determining the tritium in the different ecosystem objects and the most importantly that the tritium was detected on the surface above the nuclear testing venues. All of this confirms the possibility of using radionuclide tritium as an indicator of underground nuclear explosion venues, even after dozens of years after nuclear events. Document available in abstract form only. (authors)

Benchmark test of evaluated nuclear data files for fast reactor neutronics application

International Nuclear Information System (INIS)

Chiba, Go; Hazama, Taira; Iwai, Takehiko; Numata, Kazuyuki

2007-07-01

A benchmark test of the latest evaluated nuclear data files, JENDL-3.3, JEFF-3.1 and ENDF/B-VII.0, has been carried out for fast reactor neutronics application. For this benchmark test, experimental data obtained at fast critical assemblies and fast power reactors are utilized. In addition to comparing of numerical solutions with the experimental data, we have extracted several cross sections, in which differences between three nuclear data files affect significantly numerical solutions, by virtue of sensitivity analyses. This benchmark test concludes that ENDF/B-VII.0 predicts well the neutronics characteristics of fast neutron systems rather than the other nuclear data files. (author)

The international nuclear liability and compensation regime put to the test of a nuclear accident

International Nuclear Information System (INIS)

Reyners, P.; Tetley, M.

2003-01-01

Full text: It appears that nuclear emergency plans place generally more emphasis on the nuclear safety and radiation protection aspects of the management of an accident, both inside the installation concerned and off-site, than on the particular requirements of local residents who would find themselves suddenly in such an emergency situation and of possible victims of nuclear damage. In a similar vein, studies focusing on the international nuclear third party liability regime usually take a global perspective and leave little room for the treatment of individual cases. The albeit welcome dearth of practical experience in Western countries in providing compensation for accidents of nuclear origin has, however, meant that public and local authorities are not always fully conscious of the importance of this question which should be dealt with in as practical a manner as possible. In order to cover all the legal and practical questions that could arise during the management of the consequences of a nuclear accident with regard to third party liability, insurance and compensation, the OECD/NEA held in co-operation with French authorities a workshop in November 2001. It was decided to organize this workshop according to three main stages: the alert phase, the accident phase and the post-accident phase; and to examine during these three stages the various roles played by local and national authorities, the nuclear operator and his insurer, as well as the nature and form of their respective actions. These questions were addressed both from the angle of applicable domestic legislation and of the relevant international conventions. From the analysis of different national experiences and of the information exchanged during the workshop, a striking diversity may be noted of solutions adopted or envisaged to address various aspects of civil liability, insurance and indemnification of damage in a nuclear emergency situation. This lack of uniformity should not necessarily be

Chinese nuclear heating test reactor and demonstration plant

International Nuclear Information System (INIS)

Wang Dazhong; Ma Changwen; Dong Duo; Lin Jiagui

1992-01-01

In this report the importance of nuclear district heating is discussed. From the viewpoint of environmental protection, uses of energy resources and transport, the development of nuclear heating in China is necessary. The development program of district nuclear heating in China is given in the report. At the time being, commissioning of the 5 MW Test Heating Reactor is going on. A 200 MWt Demonstration Plant will be built. In this report, the main characteristics of these reactors are given. It shows this type of reactor has a high inherent safety. Further the report points out that for this type of reactor the stability is very important. Some experimental results of the driving facility are included in the report. (orig.)

Testing of environmentally friendly lubricants for sheet metal forming

DEFF Research Database (Denmark)

Bay, Niels; Olsson, David Dam; Andreasen, Jan Lasson

2005-01-01

the authors have especially been involved in the development of a system of test methods for sheet metal forming and in testing of friction and limits of lubrication of new, environmentally friendly lubricants. An overview of the developed tests is presented together with selected results....

Ceramic Single Phase High-Level Nuclear Waste Forms: Hollandite, Perovskite, and Pyrochlore

Science.gov (United States)

Vetter, M.; Wang, J.

2017-12-01

The lack of viable options for the safe, reliable, and long-term storage of nuclear waste is one of the primary roadblocks of nuclear energy's sustainable future. The method being researched is the incorporation and immobilization of harmful radionuclides (Cs, Sr, Actinides, and Lanthanides) into the structure of glasses and ceramics. Borosilicate glasses are the main waste form that is accepted and used by today's nuclear industry, but they aren't the most efficient in terms of waste loading, and durability is still not fully understood. Synroc-phase ceramics (i.e. hollandite, perovskite, pyrochlore, zirconolite) have many attractive qualities that glass waste forms do not: high waste loading, moderate thermal expansion and conductivity, high chemical durability, and high radiation stability. The only downside to ceramics is that they are more complex to process than glass. New compositions can be discovered by using an Artificial Neural Network (ANN) to have more options to optimize the composition, loading for performance by analyzing the non-linear relationships between ionic radii, electronegativity, channel size, and a mineral's ability to incorporate radionuclides into its structure. Cesium can be incorporated into hollandite's A-site, while pyrochlore and perovskite can incorporate actinides and lanthanides into their A-site. The ANN is used to predict new compositions based on hollandite's channel size, as well as the A-O bond distances of pyrochlore and perovskite, and determine which ions can be incorporated. These new compositions will provide more options for more experiments to potentially improve chemical and thermodynamic properties, as well as increased waste loading capabilities.

77 FR 73056 - Initial Test Programs for Water-Cooled Nuclear Power Plants

Science.gov (United States)

2012-12-07

... Plants AGENCY: Nuclear Regulatory Commission. ACTION: Draft regulatory guide; request for comment... (DG), DG-1259, ``Initial Test Programs for Water-Cooled Nuclear Power Plants.'' This guide describes... (ITPs) for light water cooled nuclear power plants. DATES: Submit comments by January 31, 2013. Comments...

Statement to the Third Conference on Facilitating the Entry into Force of the Comprehensive Nuclear-Test-Ban Treaty (CTBT). Vienna, 3 September 2003

International Nuclear Information System (INIS)

ElBaradei, M.

2003-01-01

Full text: The Third Conference on Facilitating the Entry into Force of the Comprehensive Nuclear-Test-Ban Treaty (CTBT) is being held at a time of major challenges to the nuclear arms control and disarmament regime. A verified, permanent, global ban on all types of nuclear explosive tests has been a key item on the international security agenda for nearly half a century. More than 2,000 nuclear explosive detonations have taken place since 1945, with the most recent ones in 1998. The CTBT has been characterized as the longest sought, hardest fought prize in the history of arms control. The Treaty, when implemented, will prohibit all nuclear explosions, in all environments, for all time. It will curb the development and testing of new, more advanced and more dangerous nuclear weapons, and will limit the possibilities for further nuclear proliferation. The Treaty will lead to the establishment of a comprehensive International Monitoring System to provide independent, impartial verification of compliance. The CTBT, along with the Treaty on the Non-Proliferation of Nuclear Weapons (NPT), and a future Treaty Banning the Production of Fissile Material for Nuclear Weapons and Other Nuclear Explosive Devices (FMCT), forms an essential element of a network of negotiated, global treaties that will strengthen international efforts to prevent the further spread of nuclear weapons and to promote nuclear disarmament leading in time hopefully to a world without nuclear weapons. In the meantime, with the early entry into force of the CTBT, it would indeed be a significant achievement if this new century were to remain free of any nuclear test explosions. In this context, I encourage all signatory States to ratify the CTBT, and all those States that have yet to sign to do so and to ratify the Treaty, as soon as possible - so that another crucial pillar can be raised to support the edifice of global nuclear non-proliferation and nuclear disarmament norms. (IAEA)

Materials Characterization Center workshop on leaching mechanisms of nuclear waste forms, May 19-21, 1982, Gaithersburg, Maryland. Summary report

Energy Technology Data Exchange (ETDEWEB)

Mendel, J.E. (comp.)

1982-08-01

This is a report of the second workshop on the leaching mechanism of nuclear waste forms, which was held at Geithersburg, Maryland, May 19-21, 1982. The first session of the workshop was devoted to progress reports by participants in the leaching mechanisms program. These progress reports, as prepared by the participants, are given in Section 3.0. The goal of the remainder of the workshop was to exchange information on the development of repository-relevant leach testing techniques, often called interactions testing. To this end, a wide spectrum of investigators, many of whose work is sponsored by DOE's Nuclear Waste Terminal Storage (NWTS) project, made presentations at the workshop. These presentations were a significant and beneficial part of the workshop and are summarized in Sections 4.0, 5.0 and 6.0 according to the workshop agenda topics. In many cases, the presenters provided a written version of their presentation which has been included verbatim; in the other cases, the workshop chairman has supplied a brief synopsis. Twenty-one papers have been abstracted and indexed for inclusion in the data base.

Pyrochlore as nuclear waste form. Actinide uptake and chemical stability

Energy Technology Data Exchange (ETDEWEB)

Finkeldei, Sarah Charlotte

2015-07-01

Radioactive waste is generated by many different technical and scientific applications. For the past decades, different waste disposal strategies have been considered. Several questions on the waste disposal strategy remain unanswered, particularly regarding the long-term radiotoxicity of minor actinides (Am, Cm, Np), plutonium and uranium. These radionuclides mainly arise from high level nuclear waste (HLW), specific waste streams or dismantled nuclear weapons. Although many countries have opted for the direct disposal of spent fuel, from a scientific and technical point of view it is imperative to pursue alternative waste management strategies. Apart from the vitrification, especially for trivalent actinides and Pu, crystalline ceramic waste forms are considered. In contrast to glasses, crystalline waste forms, which are chemically and physically highly stable, allow the retention of radionuclides on well-defined lattice positions within the crystal structure. Besides polyphase ceramics such as SYNROC, single phase ceramics are considered as tailor made host phases to embed a specific radionuclide or a specific group. Among oxidic single phase ceramics pyrochlores are known to have a high potential for this application. This work examines ZrO{sub 2} based pyrochlores as potential nuclear waste forms, which are known to show a high aqueous stability and a high tolerance towards radiation damage. This work contributes to (1) understand the phase stability field of pyrochlore and consequences of non-stoichiometry which leads to pyrochlores with mixed cationic sites. Mixed cationic occupancies are likely to occur in actinide-bearing pyrochlores. (2) The structural uptake of radionuclides themselves was studied. (3) The chemical stability and the effect of phase transition from pyrochlore to defect fluorite were probed. This phase transition is important, as it is the result of radiation damage in ZrO{sub 2} based pyrochlores. ZrO{sub 2} - Nd{sub 2}O{sub 3} pellets

A hydrothermal flow-through apparatus to simulate leaching of nuclear waste forms under quasi-dynamic conditions

International Nuclear Information System (INIS)

Heimann, R.B.

1985-03-01

A hydrothermal flow-through apparatus has been designed that will allow the testing of individual waste package components, as well as combinations of these, under a wide range of environmental conditions. The maximum permissible temperature is 700 degrees C, while the maximum pressure is 300 MPa. Flow rates can be adjusted by sequential operation of a pneumatically operated valve with preset pause and working cycles. The main applications of the apparatus to nuclear fuel waste management research are: (i) the study of migration of ionic species through a rock column at specified hydraulic head, and (ii) the study of the rate of leaching of radionuclides from waste forms under disposal vault conditions in the presence of groundwater with variable flow rates

Day of two suns. US nuclear testing and the Pacific Islanders

International Nuclear Information System (INIS)

Dibblin, Jane.

1988-01-01

The book focuses on two Pacific communities affected by nuclear testing, the people of Rongelap atoll irradiated by fallout, and the people of Kwajalein atoll forced to leave their islands so it could be used as a target area for missiles launched from the western USA. Both atolls are part of the Marshall Islands which are on the eastern side of the groups of islands known as Micronesia. The USA conducted 66 nuclear tests in the period 1946-1958, one on Bikini Island, codenamed Bravo, causing the contamination of Rongelap. Following the halting of atmospheric nuclear explosions in 1958 the area became a missile testing target area. The reasons why the Marshall Islands were used, the effects of the fallout and destruction of the islanders way of life when they were moved from their homes is described. It draws widely on experience of the Marshall Islanders themselves. One of the appendices lists the tests and displacement in the Marshall Islands in chronological order. (U.K.)

A System of Test Methods for Sheet Metal Forming Tribology

DEFF Research Database (Denmark)

Bay, Niels; Olsson, David Dam; Andreasen, Jan Lasson

2007-01-01

Sheet metal forming of tribologically difficult materials such as stainless steel, Al-alloys and Ti-alloys or forming in tribologically difficult operations like ironing, punching or deep drawing of thick plate requires often use of environmentally hazardous lubricants such as chlorinated paraffin...... oils in order to avoid galling. The present paper describes a systematic research in the development of new, environmentally harmless lubricants focusing on the lubricant testing aspects. A system of laboratory tests has been developed to study the lubricant performance under the very varied conditions...... appearing in different sheet forming operations such as stamping, deep drawing, ironing and punching. The laboratory tests have been especially designed to model the conditions in industrial production....

Laser-Ultrasonic Testing and its Applications to Nuclear Reactor Internals

Science.gov (United States)

Ochiai, M.; Miura, T.; Yamamoto, S.

2008-02-01

A new nondestructive testing technique for surface-breaking microcracks in nuclear reactor components based on laser-ultrasonics is developed. Surface acoustic wave generated by Q-switched Nd:YAG laser and detected by frequency-stabilized long pulse laser coupled with confocal Fabry-Perot interferometer is used to detect and size the cracks. A frequency-domain signal processing is developed to realize accurate sizing capability. The laser-ultrasonic testing allows the detection of surface-breaking microcrack having a depth of less than 0.1 mm, and the measurement of their depth with an accuracy of 0.2 mm when the depth exceeds 0.5 mm including stress corrosion cracking. The laser-ultrasonic testing system combined with laser peening system, which is another laser-based maintenance technology to improve surface stress, for inner surface of small diameter tube is developed. The generation laser in the laser-ultrasonic testing system can be identical to the laser source of the laser peening. As an example operation of the system, the system firstly works as the laser-ultrasonic testing mode and tests the inner surface of the tube. If no cracks are detected, the system then changes its work mode to the laser peening and improves surface stress to prevent crack initiation. The first nuclear industrial application of the laser-ultrasonic testing system combined with the laser peening was completed in Japanese nuclear power plant in December 2004.

Testing the predictive power of nuclear mass models

International Nuclear Information System (INIS)

Mendoza-Temis, J.; Morales, I.; Barea, J.; Frank, A.; Hirsch, J.G.; Vieyra, J.C. Lopez; Van Isacker, P.; Velazquez, V.

2008-01-01

A number of tests are introduced which probe the ability of nuclear mass models to extrapolate. Three models are analyzed in detail: the liquid drop model, the liquid drop model plus empirical shell corrections and the Duflo-Zuker mass formula. If predicted nuclei are close to the fitted ones, average errors in predicted and fitted masses are similar. However, the challenge of predicting nuclear masses in a region stabilized by shell effects (e.g., the lead region) is far more difficult. The Duflo-Zuker mass formula emerges as a powerful predictive tool

Adult education as information and help in forming opinions shown from the example of nuclear power

International Nuclear Information System (INIS)

Wild, W.; Markus, B.; Dietrich, T.; Schmitt Glaeser, W.

1977-01-01

The lectures printed here, partly in revised form, were given at a University meeting for teachers in adult education on July 9th and 10th 1976 in Bayreuth, with the main theme of 'Adult education as information and help in forming opinions shown from the subject of nuclear power'. It should be shown by examples related to this problem, which urgently requires more objectivity, and which will be freed of emotional opinions with extraordinary difficulty, how complex such objects can be and how many different aspects have to be taken into account. The grouping of scientific referees, a teacher, a nuclear physicist, a radiation biologist and a lawyer, makes the plurality of the aspects quite clear. Themes: 1) The contribution of adult education to de-idealogising the population, 2) The scientific and technical basis of generation and use of nuclear power, 3)Radiation stresses of living organismus, particularly human being. 4) Smug authorities, protesting citizens, overload judges. (GL) [de

ASEAN and the commitment to end nuclear testing

International Nuclear Information System (INIS)

2010-02-01

The Association of Southeast Asian Nations (ASEAN) is a regional political and economic organization. It was established on 8 August 1967 by Indonesia, Malaysia, the Philippines, Singapore and Thailand. Brunei Darussalam joined in 1984, Viet Nam in 1995, Laos and Myanmar in 1997 and Cambodia in 1999. ASEAN aims to accelerate economic growth, social progress and cultural development in its Member States and to promote regional peace and stability. All ASEAN States are parties to the Nuclear Non-Proliferation Treaty (NPT). The NPT aims to prevent the spread of nuclear weapons and weapons technology, and to further the goal of nuclear disarmament. It also promotes international cooperation in the peaceful uses of nuclear energy. The ten ASEAN countries are all Member States of the Preparatory Commission for the Comprehensive Nuclear-Test-Ban Treaty Organization (CTBTO). They all signed the CTBT early on, some on the very first day that it opened for signature on 24 September 1996. But four have yet to ratify the Treaty: Brunei Darussalam, Indonesia, Myanmar and Thailand. Indonesia's ratification is particularly important as it is one of those States whose ratification is required for the Treaty's entry into force.

History of creation of Semipalatinsk test nuclear site. Chapter 1

International Nuclear Information System (INIS)

1999-01-01

In 1949 August USSR's Government adopted decision about creation of nuclear site with conditional name Uchebnyj polygon 2. For its building was chosen territory in 140 km from Semipalatinsk city. Semipalatinsk test site consists of the land of three regions: Semipalatinsk, Pavlodar, Karaganda and it occupies 18,500 km 2 of fertile land, rich with minerals. Now this territory was alienated from national using. Polygon was complex object and it incorporated three main zones: Opytnoe Pole, zone of radiation safety, site Sh. Opytnoe Pole was equipped by special constructions ensuring nuclear test conducting, its observing and registration of physical measurements and occupied 2,300 km 2 . Around of the Opytnoe Pole is situated zone of radiation safety with area 45 thousand ha. Site Sh was situated in 14 km from center of Opytnoe Pole and it was intended for distribution of individual protection devices, dosimeters and for conducting of dis-activation and sanitary works. History of the site creation is connected with building of Kurchatov city. In dozen and hundred of kilometers from Kurchatov city there were top secret objects: site Balapan with total area 100,000 ha intended for conducting of nuclear tests in wells with threshold capacity 100-200 kt. Here simultaneously with main problems on the site the military-applied works were conducted on mechanics, physics of combustion, simulation of Earthquakes and determination of seismic stability of buildings and constructions. Research site Degelen with total area 33,100 ha which has been used for underground testing of nuclear charges with small capacity. Site 10 one of large research technical complex on which two reactor units were installed. Main tasks of the complex were as follows: high-temperature fuel materials testing, conducting of fundamental researches in field of physics of fissile products, thermal physics and gas hydrodynamics. On site M a laboratory base for radiochemical, radiological and chemical

Evolution of {sup 99}Tc Species in Cementitious Nuclear Waste Form

Energy Technology Data Exchange (ETDEWEB)

Um, Woo Yong; Westsik, Joseph H. [Pacific Northwest National Laboratory, Richland (United States)

2011-05-15

Technetium (Tc) is produced in large quantities as a fission product during the irradiation of {sup 235}U-enriched fuel for commercial power production and plutonium genesis for nuclear weapons. The most abundant isotope of Tc present in the wastes is {sup 99}Tc because of its high fission yield ({approx}6%) and long half-life (2.13x10{sup 5} years). During the Cold War era, generation of fissile {sup 239}Pu for use in America's atomic weapons arsenal yielded nearly 1900 kg of {sup 99}Tc at the U.S. Department of Energy's (DOE) Hanford Site in southeastern Washington State. Most of this {sup 99}Tc is present in fuel reprocessing wastes temporarily stored in underground tanks awaiting retrieval and permanent disposal. After the wastes are retrieved from the storage tanks, the bulk of the high-level waste (HLW) and lowactivity waste (LAW) stream is scheduled to be converted into a borosilicate glass waste form that will be disposed of in a shallow burial facility called the Integrated Disposal Facility (IDF) at the Hanford Site. Even with careful engineering controls, volatilization of a fraction of Tc during the vitrification of both radioactive waste streams is expected. Although this volatilized Tc can be captured in melter off-gas scrubbers and returned to the melter, some of the Tc is expected to become part of the secondary waste stream from the vitrification process. The off-gas scrubbers downstream from the melters will generate a high pH, sodium-ammonium carbonate solution containing the volatilized Tc and other fugitive species. Effective and cost-efficient disposal of Tc found in the off-gas scrubber solution remains difficult. A cementitious waste form (Cast Stone) is one of the nuclear waste form candidates being considered to solidify the secondary radioactive liquid waste that will be generated by the operation of the waste treatment plant (WTP) at the Hanford Site. Because Tc leachability from the waste form is closely related with Tc

78 FR 67206 - Qualification Tests for Safety-Related Actuators in Nuclear Power Plants

Science.gov (United States)

2013-11-08

... Nuclear Power Plants AGENCY: Nuclear Regulatory Commission. ACTION: Revision to regulatory guide; issuance..., ``Qualification Tests for Safety-Related Actuators in Nuclear Power Plants.'' This RG is being revised to provide... Operators Installed Inside the Containment of Nuclear Power Plants,'' dated January 1974. ADDRESSES: Please...

The export receptor Crm1 forms a dimer to promote nuclear export of HIV RNA.

Science.gov (United States)

Booth, David S; Cheng, Yifan; Frankel, Alan D

2014-12-08

The HIV Rev protein routes viral RNAs containing the Rev Response Element (RRE) through the Crm1 nuclear export pathway to the cytoplasm where viral proteins are expressed and genomic RNA is delivered to assembling virions. The RRE assembles a Rev oligomer that displays nuclear export sequences (NESs) for recognition by the Crm1-Ran(GTP) nuclear receptor complex. Here we provide the first view of an assembled HIV-host nuclear export complex using single-particle electron microscopy. Unexpectedly, Crm1 forms a dimer with an extensive interface that enhances association with Rev-RRE and poises NES binding sites to interact with a Rev oligomer. The interface between Crm1 monomers explains differences between Crm1 orthologs that alter nuclear export and determine cellular tropism for viral replication. The arrangement of the export complex identifies a novel binding surface to possibly target an HIV inhibitor and may point to a broader role for Crm1 dimerization in regulating host gene expression.

Leak testing United States Nuclear Regulatory Commission type b packaging

International Nuclear Information System (INIS)

Lacy, K.A.

1995-01-01

The Waste Isolation Pilot Plant (WTPP) is a one of its kind research and development facility operated by the Department of Energy, Carlsbad Area Office. Located in southeastern New Mexico, the WTPP is designed to demonstrate the safe, permanent disposal of transuranic (TRU) radioactive nuclear waste, accumulated from 40 years of nuclear weapons production. Before the waste can be disposed of, it must first be safely transported from generator storage sites to the WIPP. To accomplish this, the TRUPACT-II was designed and fabricated. This double containment, non-vented waste packaging successfully completed a rigorous testing program, and in 1989 received a Certificate of Compliance (C of C) from the Nuclear Regulatory Commission (NRC). Currently, the TRUPACT-II is in use at Idaho National Engineering Laboratory to transport waste on site for characterization. The DOE/CAO is responsible for maintaining the TRUPACT-II C of C. The C of C requires performance of nondestructive examination (NDE), e.g., visual testing (VT), dimensional inspections, Liquid Dye Penetrant testing (PT), and Helium Leak Detection (HLD). The Waste Isolation Division (WID) uses HLD for verification of the containment integrity. The following HLD tests are performed on annual basis or when required, i.e. repairs or component replacement: (1) fabrication verification leak tests on both the outer containment vessel (OCV) and the inner containment vessel (ICV); (2) assembly verification leak tests on the OCV and ICV upper main o-rings; and (3) assembly verification leak tests on the OCV and the ICV vent port plugs. These tests are addressed in detail as part of this presentation

Nuclear medicine

Energy Technology Data Exchange (ETDEWEB)

Sharma, S M [Bhabha Atomic Research Centre, Bombay (India). Radiation Medicine Centre

1967-01-01

The article deals with the growth of nuclear medicine in India. Radiopharmaceuticals both in elemental form and radiolabelled compounds became commercially available in India in 1961. Objectives and educational efforts of the Radiation Medicine Centre setup in Bombay are mentioned. In vivo tests of nuclear medicine such as imaging procedures, dynamic studies, dilution studies, thyroid function studies, renal function studies, linear function studies, blood flow, and absorption studies are reported. Techniques of radioimmunoassay are also mentioned.

Atmospheric methods for nuclear test monitoring

International Nuclear Information System (INIS)

Simons, D.J.

1995-01-01

The U.S. DOE sponsored research investigating atmospheric infrasound as a means of detecting both atmospheric and underground nuclear tests. Various detection schemes were examined and were found to be effective for different situations. It has been discovered that an enhanced sensitivity is realizable for the very lowest frequency disturbances by detecting the infrasound at the top of the atmosphere using ratio sound techniques. These techniques are compared to more traditional measurement schemes

Prediction of ground motion from underground nuclear weapons tests as it relates to siting of a nuclear waste storage facility at NTS and compatibility with the weapons test program

International Nuclear Information System (INIS)

Vortman, L.J. IV.

1980-04-01

This report assumes reasonable criteria for NRC licensing of a nuclear waste storage facility at the Nevada Test Site where it would be exposed to ground motion from underground nuclear weapons tests. Prediction equations and their standard deviations have been determined from measurements on a number of nuclear weapons tests. The effect of various independent parameters on standard deviation is discussed. That the data sample is sufficiently large is shown by the fact that additional data have little effect on the standard deviation. It is also shown that coupling effects can be separated out of the other contributions to the standard deviation. An example, based on certain licensing assumptions, shows that it should be possible to have a nuclear waste storage facility in the vicinity of Timber Mountain which would be compatible with a 700 kt weapons test in the Buckboard Area if the facility were designed to withstand a peak vector acceleration of 0.75 g. The prediction equation is a log-log linear equation which predicts acceleration as a function of yield of an explosion and the distance from it

Technology Implementation Plan: Irradiation Testing and Qualification for Nuclear Thermal Propulsion Fuel

Energy Technology Data Exchange (ETDEWEB)

Harrison, Thomas J. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Howard, Richard H. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Rader, Jordan D. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States)

2017-09-01

This document is a notional technology implementation plan (TIP) for the development, testing, and qualification of a prototypic fuel element to support design and construction of a nuclear thermal propulsion (NTP) engine, specifically its pre-flight ground test. This TIP outlines a generic methodology for the progression from non-nuclear out-of-pile (OOP) testing through nuclear in-pile (IP) testing, at operational temperatures, flows, and specific powers, of an NTP fuel element in an existing test reactor. Subsequent post-irradiation examination (PIE) will occur in existing radiological facilities. Further, the methodology is intended to be nonspecific with respect to fuel types and irradiation or examination facilities. The goals of OOP and IP testing are to provide confidence in the operational performance of fuel system concepts and provide data to program leadership for system optimization and fuel down-selection. The test methodology, parameters, collected data, and analytical results from OOP, IP, and PIE will be documented for reference by the NTP operator and the appropriate regulatory and oversight authorities. Final full-scale integrated testing would be performed separately by the reactor operator as part of the preflight ground test.

A patient-derived mutant form of the Fanconi anemia protein, FANCA, is defective in nuclear accumulation.

Science.gov (United States)

Kupfer, G; Naf, D; Garcia-Higuera, I; Wasik, J; Cheng, A; Yamashita, T; Tipping, A; Morgan, N; Mathew, C G; D'Andrea, A D

1999-04-01

Fanconi anemia (FA) is an autosomal recessive cancer susceptibility syndrome with at least eight complementation groups (A-H). Three FA genes, corresponding to complementation groups A, C, and G, have been cloned, but the function of the encoded FA proteins remains unknown. We recently demonstrated that the FANCA and FANCC proteins bind and form a nuclear complex. In the current study, we identified a homozygous mutation in the FANCA gene (3329A>C) in an Egyptian FA patient from a consanguineous family. This mutant FANCA allele is predicted to encode a mutant FANCA protein, FANCA(H1110P), in which histidine 1110 is changed to proline. Initially, we characterized the FANCA(H1110P) protein, expressed in an Epstein Barr virus (EBV)-immortalized lymphoblast line derived from the patient. Unlike wild-type FANCA protein expressed in normal lymphoblasts, FANCA(H1110P) was not phosphorylated and failed to bind to FANCC. To test directly the effect of this mutation on FANCA function, we used retroviral-mediated transduction to express either wild-type FANCA or FANCA(H1110P) protein in the FA-A fibroblast line, GM6914. Unlike wild-type FANCA, the mutant protein failed to complement the mitomycin C sensitivity of these cells. In addition, the FANCA(H1110P) protein was defective in nuclear accumulation in the transduced cells. The characteristics of this mutant protein underscore the importance of FANCA phosphorylation, FANCA/FANCC binding, and nuclear accumulation in the function of the FA pathway.

Validation of a Short Form of an Indecision Test: The Vocational Assessment Test

Science.gov (United States)

Picard, France; Frenette, Éric; Guay, Frédéric; Labrosse, Julie

2015-01-01

The purpose of this research was to validate the scores of a short form of a new instrument, "l'Épreuve de décision vocationnelle, forme scolaire" (EDV-9S; vocational assessment test), which measures six indecision-related problems (lack of self-knowledge, lack of readiness, lack of method in decision making, lack of information,…

Second study of UK nuclear test participants

International Nuclear Information System (INIS)

Darby, S.; Doll, R.; Kendall, G.

1994-01-01

A second epidemiological analysis of mortality and cancer incidence in UK participants in the UK atmospheric nuclear tests and associated experimental programmes has provided broadly reassuring results. Overall death rates in test participants are lower than those in the general population and similar to those in a closely matched control group. Observations in the extended period of follow-up suggest that the excess of multiple myeloma seen in the first analysis was a chance finding. The extended follow-up does not provide any new evidence to support the finding of apparent excess of leukaemia found in the first analysis. However, the possibility that test participation may have caused a small risk of leukaemia in the early years after the tests cannot be ruled out. (author)

Prohibiting and Preventing Nuclear Explosions: Background Information for Parliamentarians on the Comprehensive Nuclear-Test-Ban Treaty (CTBT)

International Nuclear Information System (INIS)

2010-07-01

The object and purpose of the CTBT is to ban comprehensively nuclear weapon test explosions and any other nuclear explosion in any environment in an effectively verifiable manner. The CTBT aims at eliminating nuclear weapons by constraining the development and qualitative improvement of new or more advanced nuclear weapons. It plays a crucial role in the prevention of nuclear proliferation and in nuclear disarmament, thus contributing to a safer and more secure world. When the Treaty enters into force it will establish a treaty-implementing body (the Comprehensive Nuclear-Test-Ban Treaty Organization (CTBTO)), including an on-site inspection mechanism and confidence-building measures as well as an International Monitoring System (IMS) and International Data Centre (IDC). The IMS and IDC are already being created and are being provisionally operated during the preparatory phase by the Preparatory Commission for the CTBTO and its Provisional Technical Secretariat in Vienna. Seismic, hydroacoustic, infrasound and radionuclide data are collected through the stations of the IMS and transmitted to Member States via the IDC. The IDC also processes the raw data received from the stations to derive objective products and services which will support the Treaty verification responsibilities. If the collected and analysed data indicate an ambiguous event, States may address concerns about possible noncompliance with the Treaty through a consultation and clarification process after it enters into force and may request an on-site inspection by the CTBTO.

The use of eddy current testing for nuclear fuel rods cladding evaluation

International Nuclear Information System (INIS)

Silva Junior, Silverio F. da; Alencar, Donizete A.; Brito, Mucio Jose D. de

2007-01-01

Nuclear fuel rods cladding must be tested after their manufacture and during their operational life. This paper describes a study about the use of eddy current test method as a nondestructive tool for nuclear fuel rods cladding evaluation. The experiments were carried out using two different probes: an external probe and an internal probe. The main goal was to verify the sensitivity of the eddy current test system, to develop calibration and reference standards and to establish the main capabilities and limitations presented by this test method for this application. (author)

Waste form development/test

International Nuclear Information System (INIS)

Kalb, P.D.; Colombo, P.

1983-01-01

The main objective of this study is to investigate new solidification agents relative to their potential application to wastes generated by advanced high volume reduction technologies, e.g., incinerator ash, dry solids, and ion exchange resins. Candidate materials selected for the solidification of these wastes include a modified sulfur cement and low-density polyethylene, neither of which are currently employed commerically for the solidification of low-level waste (LLW). As both the modified sulfur cement and the polyethylene are thermoplastic materials, a heated screw type extruder is utilized in the production of waste form samples for testing and evaluation. In this regard, work is being conducted to determine the range of conditions under which these solidification agents can be satisfactorily applied to the specific LLW streams and to provide information relevant to operating parameters and process control

Inquiry close to veterans consequences on health of French nuclear tests. Primary results introduced to the International Conference on French nuclear tests at Hiroshima on the 5. august 2002

International Nuclear Information System (INIS)

Valatx, J.L.

2005-01-01

The association of veterans of nuclear tests(A.V.E.N.) has been created on the 9. june 2001. It concerns the military personnel, the Cea personnel and the contractors personnel that took part in nuclear tests in the Algerian Sahara and French Polynesia. A.V.E.N. has for objective information on the consequences of nuclear tests, the entitlement to have access to their medical file and the right to compensation for loss sustained by the victims. The inquiry bearing on 271 veterans brings to light that 93.4% of them have one or several diseases, 28.4% of them have or had one or several cancers. 77% of cancers happened before sixty years old and 36% before fifty years old. 45.4% died before sixty years old. The non cancerous digestive, osteo-muscular and cardiovascular pathologies are the most frequent. The children and grand children present inborn malformations (9.4% and 4.8%) and various diseases (24.3% and 5.5%). Despite that the critics that can be formulated, the results, compared to the British ones incite to go on. This preliminary inquiry must be completed by a greater number of answers. These results are an important argument to ask for an epidemiology inquiry on the whole of military and civil personnel that have participated to the nuclear tests in order to establish in a definite way the effects on health of nuclear tests and to draw consequences of it. (N.C.)

Technical management on commissioning test of nuclear heating reactor

International Nuclear Information System (INIS)

Zhang Yajun; Su Qingshan

1999-01-01

The commissioning is the last construction stage of a nuclear heating project. The commissioning quality will directly affect on the safe operation and availability of the heating reactor. The author presents the whole test process until the completion of the test report from the point of test documents, including the preparation and execution of the test, the management of the various unexpected events during the test. And it will be emphatically discussed that the managing procedures of the various unexpected events during the test, including temporary control change, setpoint change, unexpected events and design change

The initial criticality and nuclear commissioning test program at HANARO

Energy Technology Data Exchange (ETDEWEB)

Lee, Choong-Sung; Seo, Chul-Gyo; Jun, Byung-Jin [Korea Atomic Energy Research Institute, Dukjin-Dong 150, Yusung-Ku, Taejon, 305-353 (Korea, Republic of)

1995-07-01

The construction of the Korea Multipurpose Research Reactor - HANARO of 3MW, developed by Korea Atomic Energy Research Institute, was completed at the beginning of this year. The first fuel loading began on February 2 1995, and initial criticality was achieved on February 8, when the core had four 18-element assemblies and thirteen 36-element assemblies. The critical control rod position was 600.8 mm which represents excess reactivity of 0.71 $. Currently the nuclear commissioning test is on going under the zero power range. This paper describes the initial criticality approach of the HANARO, and its nuclear commissioning test program. (author)

Summary revaluation of cold testing of the first block of nuclear power plant Mochovce

International Nuclear Information System (INIS)

Miskolci, M.; Sarvaic, I.

1998-01-01

The document contents summary revaluation of the stage of cold testing of the first unit of nuclear power plant Mochovce. The valuation is processed in individual systems with safety significance. The process and results of system testing and their conclusions for the block readiness for active testing are summarized in the document. The valuation has been elaborated by a scientific management for start-up of nuclear power plant Mochovce as an independent conductor assistance for activation check from the nuclear safety point of view. The valuation of the activation results of systems in the first unit of nuclear power plant was processed as of 15.3.1998

Soviet Nuclear Strategy form Stalin to Gorbachev

International Nuclear Information System (INIS)

Catudal, H.M.

1989-01-01

This book examines the nature of the Soviet nuclear threat and how it has evolved over the years. Too often in the past U.S. officials, in shaping and directing plans for American nuclear forces, have tended to see Soviet military forces and strategy as a reflection of their own stance or simply as projecting the worst plausible case of Soviet intentions and capabilities. The result has been a distorted if not dangerous portrayal of the real threat. Soviet nuclear strategy, as explained in this detailed book, has evolved significantly since the days when the Soviets first possessed nuclear weapons under Joseph Stalin. Today there is in development a new Soviet military and strategic doctrine reflected in Gorbachev's words, We require a radical break with traditions of political thinking. This new doctrine promises to have a profound impact on European security and the overall East-West relationship

76 FR 52355 - NUREG-1482, Revision 2, “Guidelines for Inservice Testing at Nuclear Power Plants, Draft Report...

Science.gov (United States)

2011-08-22

... Testing at Nuclear Power Plants, Draft Report for Comment'' AGENCY: Nuclear Regulatory Commission. ACTION... Testing at Nuclear Power Plants, Draft Report for Comment,'' and subtitled ``Inservice Testing of Pumps... Examination and Testing of Dynamic Restraints (Snubbers) at Nuclear Power Plants'' is available electronically...

Standard test methods for chemical, mass spectrometric, spectrochemical, nuclear, and radiochemical analysis of nuclear-grade plutonium nitrate solutions

CERN Document Server

American Society for Testing and Materials. Philadelphia

2010-01-01

1.1 These test methods cover procedures for the chemical, mass spectrometric, spectrochemical, nuclear, and radiochemical analysis of nuclear-grade plutonium nitrate solutions to determine compliance with specifications. 1.2 The analytical procedures appear in the following order: Sections Plutonium by Controlled-Potential Coulometry Plutonium by Amperometric Titration with Iron(II) Plutonium by Diode Array Spectrophotometry Free Acid by Titration in an Oxalate Solution 8 to 15 Free Acid by Iodate Precipitation-Potentiometric Titration Test Method 16 to 22 Uranium by Arsenazo I Spectrophotometric Test Method 23 to 33 Thorium by Thorin Spectrophotometric Test Method 34 to 42 Iron by 1,10-Phenanthroline Spectrophotometric Test Method 43 to 50 Impurities by ICP-AES Chloride by Thiocyanate Spectrophotometric Test Method 51 to 58 Fluoride by Distillation-Spectrophotometric Test Method 59 to 66 Sulfate by Barium Sulfate Turbidimetric Test Method 67 to 74 Isotopic Composition by Mass Spectrom...

The characterization and testing of candidate immobilization forms for the disposal of plutonium

International Nuclear Information System (INIS)

Bakel, A. J.; Buck, E. C.; Chamberlain, D. B.; Ebbinghaus, B. B.; Fortner, J. A.; Marra, J. C.; Mcgrail, B. P.; Mertz, C. J.; Peeler, D. K.; Shaw, H. F.; Strachan, D. M.; Van Konynenburg, R. A.; Vienna, J. D.; Wolf, S. F.

1997-01-01

Candidate immobilization forms for the disposal of surplus weapons-useable are being tested and characterized. The goal of the testing program was to provide sufficient data that, by August 1997, an informed selection of a single immobilization form could be made so that the form development and production R and D could be more narrowly focused. Two forms have been under consideration for the past two years: glass and ceramic. In August, 1997, the Department of Energy (DOE) selected ceramic for plutonium disposition, halting further work on the glass material. In this paper, we will briefly describe these two waste forms, then describe our characterization techniques and testing methods. The analytical methods used to characterize altered and unaltered samples are the same. A full suite of microscopic techniques is used. Techniques used include optical, scanning electron, and transmission electron microscopies. For both candidate immobilization forms, the analyses are used to characterize the material for the presence of crystalline phases and amorphous material. Crystalline materials, either in the untested immobilization form or in the alteration products from testing, are characterized with respect to morphology, crystal structure, and composition. The goal of these analyses is to provide data on critical issues such as Pu and neutron absorber volubility in the immobilization form, thermal stability, potential separation of absorber and Pu, and the long-term behavior of the materials. Results from these analyses will be discussed in the presentation. Testing methods include MCC-1 tests, product consistency tests (methods A and B), unsaturated ''drip'' tests, vapor hydration tests, single-pass flow-through tests, and pressurized unsaturated flow tests. Both candidate immobilization forms have very low dissolution rates; examples of typical test results will be reported

Assessment of the announced North Korean nuclear test using long-range atmospheric transport and dispersion modelling.

Science.gov (United States)

De Meutter, Pieter; Camps, Johan; Delcloo, Andy; Termonia, Piet

2017-08-18

On 6 January 2016, the Democratic People's Republic of Korea announced to have conducted its fourth nuclear test. Analysis of the corresponding seismic waves from the Punggye-ri nuclear test site showed indeed that an underground man-made explosion took place, although the nuclear origin of the explosion needs confirmation. Seven weeks after the announced nuclear test, radioactive xenon was observed in Japan by a noble gas measurement station of the International Monitoring System. In this paper, atmospheric transport modelling is used to show that the measured radioactive xenon is compatible with a delayed release from the Punggye-ri nuclear test site. An uncertainty quantification on the modelling results is given by using the ensemble method. The latter is important for policy makers and helps advance data fusion, where different nuclear Test-Ban-Treaty monitoring techniques are combined.

Current developments in mechanized non-destructive testing in nuclear power plants

International Nuclear Information System (INIS)

Zeilinger, R.

2008-01-01

Nuclear power plants require frequent in-service activities to be carried out conscientiously in areas potentially hazardous to human operators (because of the associated radiation exposure), such as non-destructive testing of pressurized components of the steam system. Locations to be inspected in this way include the reactor pressure vessel, core internals, steam generators, pressurizers, and pipes. The codes to be used as a basis of these inspections demand high absolute positioning and repeating accuracy. These requirements can be met by mechanized test procedures. Accordingly, many new applications of, mostly mobile, robots have been developed over the past few years. The innovative control and sensor systems for stationary and mobile robots now on the market offer a potential for economic application in a large number of new areas in inspection, maintenance and service in nuclear power plants. More progress in this area is expected for the near future. Areva NP founded the new NDT Center, NETEC (Non-destructive Examination Technical Center), as a global technical center for non-destructive materials testing. NETEC is to advance research and development of all basic NDT technologies, robotics included. For many years, intelligeNDT has offered solutions and products for a variety of inspection and testing purposes and locations in nuclear power plants and is involved in continuous further development of the experience collected in nuclear power plants on the spot. (orig.)

Smart built-in test for nuclear thermal propulsion

International Nuclear Information System (INIS)

Lombrozo, P.C.

1992-03-01

Smart built-in test (BIT) technologies are envisioned for nuclear thermal propulsion spacecraft components which undergo constant irradiation and are therefore unsafe for manual testing. Smart BIT systems of automated/remote type allow component and system tests to be conducted; failure detections are directly followed by reconfiguration of the components affected. The 'smartness' of the BIT system in question involves the reduction of sensor counts via the use of multifunction sensors, the use of components as integral sensors, and the use of system design techniques which allow the verification of system function beyond component connectivity

Laboratory procedures for waste form testing

International Nuclear Information System (INIS)

Mast, E.S.

1994-01-01

The 100 and 300 areas of the Hanford Site are included on the US Environmental Protection Agencies (EPA) National Priorities List under the Comprehensive Environmental Response, Compensation, and Liability Act (CERCLA). Soil washing is a treatment process that is being considered for the remediation of the soil in these areas. Contaminated soil washing fines can be mixed or blended with cementations materials to produce stable waste forms that can be used for beneficial purposes in mixed or low-level waste landfills, burial trenches, environmental restoration sites, and other applications. This process has been termed co-disposal. The Co-Disposal Treatability Study Test Plan is designed to identify a range of cement-based formulations that could be used in disposal efforts in Hanford in co-disposal applications. The purpose of this document is to provide explicit procedural information for the testing of co-disposal formulations. This plan also provides a discussion of laboratory safety and quality assurance necessary to ensure safe, reproducible testing in the laboratory

Laboratory procedures for waste form testing

Energy Technology Data Exchange (ETDEWEB)

Mast, E.S.

1994-09-19

The 100 and 300 areas of the Hanford Site are included on the US Environmental Protection Agencies (EPA) National Priorities List under the Comprehensive Environmental Response, Compensation, and Liability Act (CERCLA). Soil washing is a treatment process that is being considered for the remediation of the soil in these areas. Contaminated soil washing fines can be mixed or blended with cementations materials to produce stable waste forms that can be used for beneficial purposes in mixed or low-level waste landfills, burial trenches, environmental restoration sites, and other applications. This process has been termed co-disposal. The Co-Disposal Treatability Study Test Plan is designed to identify a range of cement-based formulations that could be used in disposal efforts in Hanford in co-disposal applications. The purpose of this document is to provide explicit procedural information for the testing of co-disposal formulations. This plan also provides a discussion of laboratory safety and quality assurance necessary to ensure safe, reproducible testing in the laboratory.

Sustainable land use planning at the Semipalatinsk Nuclear Test Site

International Nuclear Information System (INIS)

Coughtrey, P.J.; Ridgway, R.B.; Baumann, P.

2001-01-01

Full text: The UK Department for International Development (DFID) has recently agreed to support a project to develop a participatory sustainable land use plan for areas affected by nuclear weapons testing at Semipalatinsk. This three year project is expected to be initiated in April 2001 and will form one component of the United Nations Development Programme (UNDP) Semipalatinsk Rehabilitation Programme. The project will be undertaken by a combination of Kazakh organizations working with UK consultants and will meet its overall aim through the following main activities: Development of institutional capacity in data management and analysis; Provision of information and education on environmental contamination, hazards and risks; Development of a participatory land use planning process and piloting of the process in specific areas and communities around the test site; Integration of mineral resource extraction in the land planning process with a focus- on water resource and environmental protection and participatory approaches to resolving land use conflicts; Development of legislative tools to permit the implementation of environmental management of resource exploitation. The project will make use of both modern satellite-based imagery and more traditional methods to determine the potential for different land uses within the test site. The results obtained will be incorporated with additional information on land use. radiological and hydrological conditions at the test site through a geographical information system (GIS) provided by the project. The GIS will form the core component for collation and distribution of information on options available for use of different areas of the test site and its vicinity. A participatory rural appraisal, using tried and tested techniques, will identify local interest groups in land use planning and identify the details of their stake in the process. The groups will include owners-herders, employee-herders, and subsistence

North Korea nuclear test analysis results using KMA seismic and infrasound networks

Science.gov (United States)

Jeon, Y. S.; Park, E.; Lee, D.; Min, K.; CHO, S.

2017-12-01

Democratic People's Republic of Korea(DPRK) carried out 6th nuclear test on 3 Sep. 2017 at 03:30 UTC. Seismic and infrasound network operated by Korea Meteorological Administration(KMA) successfully detected signals took place in the DPRK's test site, Punggye-ri. First, we checked that Pg/Lg spectral amplitude ratio greater than 1 in the frequency range from 1.0 to 10.0 Hz is useful to discriminate between DPRK test signals and natural earthquakes. KMA's infrasound stations of Cheorwon(CW) and Yanggu(YG) successfully monitored the azimuth direction of the arrival of the infrasound signals generated from DPRK underground nuclear explosions, including the recent test on September 03, 2017. The azimuthal direction of 210(CW) and 130 (YG) point out Punggye-ri test site. Complete waveforms at stations MDJ, CHC2, YNCB in long period(0.05 to 0.1 HZ) are jointly inverted with local P-wave polarities to generate moment tensor inversion result of the explosive moment 1.20e+24 dyne cm(Mw 5.31) and 65% of ISO. The moment magnitude of 5th, 4th and 3rd are 4.61, 4.69 and 4.46 respectively. Source type moment tensor inversion result of DPRK nuclear tests show that the event is significantly away from the deviatoric line of the Hudson et at. (1989) source-type diagram and identifies as having a significant explosive component. Analysis results using seismic and infrasound network verify that the DPRK's explosion tests classified as nuclear test.

NUCLEBRAS' installations for tests of nuclear power plants components

International Nuclear Information System (INIS)

Vasconcelos Paiva, I.P. de; Horta, J.A.L.; Avelar Esteves, F. de; Pinheiro, R.B.

1983-05-01

The reasons for NUCLEBRAS' Nuclear Technology Development Center to implement a laboratory for supporting Brazilian manufacturers, giving to them the means for performing functional tests of industrial products, are presented. A brief description of the facilities under construction: the Components Test Loop and the Facility for Testing N.P.P. Components under Accident Conditions, and of other already in operation, is given, as well as its objectives and main technical characteristics. Some test results already obtained are also presented. (Author) [pt

[Alternate form of the test de aprendizaje verbal España-Complutense (TAVEC)].

Science.gov (United States)

Nieto, Antonieta; Hernández-Rodríguez, Edith; Hernández-Torres, Atteneri; Velasco Rodríguez-Solís, Pedro; Hess-Medler, Stephany; Machado-Fernández, Alejandra; Molina-Rodríguez, Yaiza; Barroso, José

2014-05-01

Parallel forms of neuropsychological tests are scarce. Practice effects associated to repeated testing with the same test confound the interpretation of observed changes in serial assessments. Practice effects are especially likely with memory testing. To develop an alternate form to the test de aprendizaje verbal España-Complutense (TAVEC), one of the most common memory tests used for Spanish speaking population. Participants in the normative study were 110 undergraduates. Participants in the study of the alternate vs original forms were 70 neurologically normal volunteers ranged in age from 18 to 89 years. Forms were administered in counterbalanced order, with a test-retest interval of 15-20 days. Multivariate analyses showed that none of the effects for form, order of administration or session achieved significance. Interactions also failed to reach significance. Aforementioned results were observed in the total sample and the different age groups: young adults (18-29 years), middle-age (30-59 years) and older (60-89 years). Correlational analyses supported the validity and internal consistence of the alternate form. Results indicate the equivalence between the original TAVEC and the form elaborated in this study. This alternate form may be used in serial assessment of learning and memory deterioration.

Radiation exposure on residents due to semipalatinsk nuclear tests

International Nuclear Information System (INIS)

Takada, J.; Hoshi, M.; Nagatomo, T.

2000-01-01

Accumulated external radiation doses for residents near Semipalatinsk nuclear test site of the former USSR are presented as a results of the first study by thermoluminescence technique for bricks sampled at several settlements between 1995 and 1997. The external doses which we evaluated from brick dose were up to ∼100 cGy for resident. The external doses at several points in the center of Semipalatinsk city were ∼60 cGy that was remarkably high comparing with the previously reported value based on the military data. A total of 459 nuclear explosions were conducted by the former Union of Soviet Socialist Republics (USSR) from 1949 to 1989 at the Semipalatinsk nuclear test site (SNTS) Kazakhstan, including 87 atmospheric, 26 on the ground, and 364 underground explosions. Total energy release of about 18 Mt equivalent of trinitrotoluene is eleven hundreds times of Hiroshima atomic bomb. However previous reports concerning the effects of radiation on residents near the SNTS based on data provided by the Defense Department of the former USSR do not have direct experimental data concerning effective equivalent dose. They just measured some doses for particular settlements after some nuclear explosions. These do not indicate integrated dose for the residents due to the whole explosions. The technique of thermoluminescence dosimetry (TLD) which had been successfully applied to the dosimetry on Hiroshima and Nagasaki atomic bombs, enabled us to evaluate accumulated external gamma ray doses at specific places due to whole nuclear explosions in the Semipalatinsk test site. TLD technique is well-established one for not only instantaneous exposure like in A-bombs (Hiroshima and Nagasaki) but also prolonged exposure like in dating. Moreover this technique was applicable for dosimetry study of radioactive fallout as shown in studies of Chernobyl accident. The way of external dose estimation from TLD doses for brick will be discussed in case of radioactive fallout. We will

RECENT ACTIVITIES AT THE CENTER FOR SPACE NUCLEAR RESEARCH FOR DEVELOPING NUCLEAR THERMAL ROCKETS

International Nuclear Information System (INIS)

O'Brien, Robert C.

2001-01-01

Nuclear power has been considered for space applications since the 1960s. Between 1955 and 1972 the US built and tested over twenty nuclear reactors/ rocket-engines in the Rover/NERVA programs. However, changes in environmental laws may make the redevelopment of the nuclear rocket more difficult. Recent advances in fuel fabrication and testing options indicate that a nuclear rocket with a fuel form significantly different from NERVA may be needed to ensure public support. The Center for Space Nuclear Research (CSNR) is pursuing development of tungsten based fuels for use in a NTR, for a surface power reactor, and to encapsulate radioisotope power sources. The CSNR Summer Fellows program has investigated the feasibility of several missions enabled by the NTR. The potential mission benefits of a nuclear rocket, historical achievements of the previous programs, and recent investigations into alternatives in design and materials for future systems will be discussed.

The construction of solid waste form test and inspection facility

International Nuclear Information System (INIS)

Park, Hun Hwee; Lee, Kang Moo; Jung, In Ha; Kim, Sung Hwan; Yoo, Jeong Woo; Lee, Jong Youl; Bae, Sang Min

1988-01-01

The solid waste form test and inspection facility is a facility to test and inspect the characteristics of waste forms, such as homogenity, mechanical structure, thermal behaviour, water resistance and leachability. Such kinds of characteristics in waste forms are required to meet a certain conditions for long-term storage or for final disposal of wastes. The facility will be used to evaluate safety for the disposal of wastes by test and inspection. At this moment, the efforts to search the most effective management of the radioactive wastes generated from power plants and radioisotope user are being executed by the people related to this field. Therefore, the facility becomes more significant tool because of its guidance of sucessfully converting wastes into forms to give a credit to the safety of waste disposal for managing the radioactive wastes. In addition the overall technical standards for inspecting of waste forms such as the standardized equipment and processes in the facility will be estabilished in the begining of 1990's when the project of waste management will be on the stream. Some of the items of the project have been standardized for the purpose of localization. In future, this facility will be utilized not only for the inspection of waste forms but also for the periodic decontamination apparatus by remote operation techniques. (Author)

Population Health in Regions Adjacent to the Semipalatinsk Nuclear Test Site

National Research Council Canada - National Science Library

1998-01-01

...) of the Union of Soviet Socialist Republics (USSR). Inhabitants of several Kazakhstan regions were contaminated in different years by radioactive fallout from atmospheric nuclear tests at the Semipalatinsk test site...

Operation of the nuclear fuel cycle test facilities -Operation of the hot test loop facilities

International Nuclear Information System (INIS)

Chun, S. Y.; Jeong, M. K.; Park, C. K.; Yang, S. K.; Won, S. Y.; Song, C. H.; Jeon, H. K.; Jeong, H. J.; Cho, S.; Min, K. H.; Jeong, J. H.

1997-01-01

A performance and reliability of a advanced nuclear fuel and reactor newly designed should be verified by performing the thermal hydraulics tests. In thermal hydraulics research team, the thermal hydraulics tests associated with the development of an advanced nuclear fuel and reactor haven been carried out with the test facilities, such as the Hot Test Loop operated under high temperature and pressure conditions, Cold Test Loop, RCS Loop and B and C Loop. The objective of this project is to obtain the available experimental data and to develop the advanced measuring techniques through taking full advantage of the facilities. The facilities operated by the thermal hydraulics research team have been maintained and repaired in order to carry out the thermal hydraulics tests necessary for providing the available data. The performance tests for the double grid type bottom end piece which was improved on the debris filtering effectivity were performed using the PWR-Hot Test Loop. The CANDU-Hot Test Loop was operated to carry out the pressure drop tests and strength tests of CANFLEX fuel. The Cold Test Loop was used to obtain the local velocity data in subchannel within HANARO fuel bundle and to study a thermal mixing characteristic of PWR fuel bundle. RCS thermal hydraulic loop was constructed and the experiments have been carried out to measure the critical heat flux. In B and C Loop, the performance tests for each component were carried out. (author). 19 tabs., 78 figs., 19 refs

Operation of the nuclear fuel cycle test facilities -Operation of the hot test loop facilities

Energy Technology Data Exchange (ETDEWEB)

Chun, S. Y.; Jeong, M. K.; Park, C. K.; Yang, S. K.; Won, S. Y.; Song, C. H.; Jeon, H. K.; Jeong, H. J.; Cho, S.; Min, K. H.; Jeong, J. H.

1997-01-01

A performance and reliability of a advanced nuclear fuel and reactor newly designed should be verified by performing the thermal hydraulics tests. In thermal hydraulics research team, the thermal hydraulics tests associated with the development of an advanced nuclear fuel and reactor haven been carried out with the test facilities, such as the Hot Test Loop operated under high temperature and pressure conditions, Cold Test Loop, RCS Loop and B and C Loop. The objective of this project is to obtain the available experimental data and to develop the advanced measuring techniques through taking full advantage of the facilities. The facilities operated by the thermal hydraulics research team have been maintained and repaired in order to carry out the thermal hydraulics tests necessary for providing the available data. The performance tests for the double grid type bottom end piece which was improved on the debris filtering effectivity were performed using the PWR-Hot Test Loop. The CANDU-Hot Test Loop was operated to carry out the pressure drop tests and strength tests of CANFLEX fuel. The Cold Test Loop was used to obtain the local velocity data in subchannel within HANARO fuel bundle and to study a thermal mixing characteristic of PWR fuel bundle. RCS thermal hydraulic loop was constructed and the experiments have been carried out to measure the critical heat flux. In B and C Loop, the performance tests for each component were carried out. (author). 19 tabs., 78 figs., 19 refs.

Subcritical tests - nuclear weapon testing under the Comprehensive Test Ban Treaty

International Nuclear Information System (INIS)

Hoeibraaten, S.

1998-10-01

The report discusses possible nuclear weapons related experiments and whether these are permitted under the 1996 Comprehensive Test Ban Treaty (CTBT). The term ''subcritical experiments'' as used in the United States includes experiments in which one studies fissile materials (so far only plutonium) under extreme conditions generated by conventional high explosives, and in which a self-sustained chain reaction never develops in the fissile material. The known facts about the American subcritical experiments are presented. There is very little reason to doubt that these experiments were indeed subcritical and therefore permitted under the CTBT. Little is known about the Russian efforts that are being made on subcritical experiments

Effluent treatment options for nuclear thermal propulsion system ground tests

International Nuclear Information System (INIS)

Shipers, L.R.; Brockmann, J.E.

1992-01-01

A variety of approaches for handling effluent from nuclear thermal propulsion system ground tests in an environmentally acceptable manner are discussed. The functional requirements of effluent treatment are defined and concept options are presented within the framework of these requirements. System concepts differ primarily in the choice of fission-product retention and waste handling concepts. The concept options considered range from closed cycle (venting the exhaust to a closed volume or recirculating the hydrogen in a closed loop) to open cycle (real time processing and venting of the effluent). This paper reviews the strengths and weaknesses of different methods to handle effluent from nuclear thermal propulsion system ground tests

Testing for Nuclear Thermal Propulsion Systems: Identification of Technologies for Effluent Treatment in Test Facilities

Data.gov (United States)

National Aeronautics and Space Administration — Key steps to ensure identification of relevant effluent treatment technologies for Nuclear Thermal Propulsion (NTP) testing include the following. 1. Review of...

Cancer, reproductive abnormalities, and diabetes in Micronesia: the effect of nuclear testing.

Science.gov (United States)

Yamada, Seiji

2004-09-01

Many suggest that cancer and other diseases in Micronesia have been caused by nuclear testing in the Pacific. The 50-year commemoration of the March 1, 1954 Bravo thermonuclear test has rekindled interest in this area. This paper explores the documentation for, and the plausibility of, claims for disease causation by nuclear testing. Given the sheer volume of testing that the US conducted in the Pacific, it appears plausible that excess cancer would have occurred in areas of Micronesia other than the Marshall Islands. An excess of birth abnormalities in the Marshall Islands has been documented. While diabetes is not a radiogenic disease, and other cancers are generally less radiogenic than leukemia or thyroid cancer, the social and cultural effects of nuclear testing specifically, and the strategic uses to which Micronesia has been put generally, have had roles in the social production of disease. Integration into a globalized, cosmopolitan economy-with attendant phenomena such as the importation of tobacco, alcohol, foods of poor nutritional value, and new cultural morés-are also factors.

Proposition of law relative to the sanitary follow up of French nuclear tests

International Nuclear Information System (INIS)

2008-03-01

The present proposition of law has for object to answer the expectation of all the persons who have participated as military personnel or civilians in nuclear tests made by France between February 13., 1960 and January 27., 1996, or lived near the nuclear test sites of Sahara (Reggane) or in French Polynesia. The same pathologies are noticed among the veteran or the populations having lived near the nuclear tests sites of the other nuclear countries which made the same experiments. It is the case in United States, in Great Britain, in Australia, in New Zealand and in Fidgi. In these different countries having a democratic system similar to ours, the governments took concrete measures to accede to the demands of their nationals. It thus turns out that a legislative initiative would represent a strong message of gratitude towards all those who had to undergo aftereffects on their health and that of their descendants of the only fact of their participation in the nuclear experiments of France. (N.C.)

Ground Testing a Nuclear Thermal Rocket: Design of a sub-scale demonstration experiment

Energy Technology Data Exchange (ETDEWEB)

David Bedsun; Debra Lee; Margaret Townsend; Clay A. Cooper; Jennifer Chapman; Ronald Samborsky; Mel Bulman; Daniel Brasuell; Stanley K. Borowski

2012-07-01

In 2008, the NASA Mars Architecture Team found that the Nuclear Thermal Rocket (NTR) was the preferred propulsion system out of all the combinations of chemical propulsion, solar electric, nuclear electric, aerobrake, and NTR studied. Recently, the National Research Council committee reviewing the NASA Technology Roadmaps recommended the NTR as one of the top 16 technologies that should be pursued by NASA. One of the main issues with developing a NTR for future missions is the ability to economically test the full system on the ground. In the late 1990s, the Sub-surface Active Filtering of Exhaust (SAFE) concept was first proposed by Howe as a method to test NTRs at full power and full duration. The concept relied on firing the NTR into one of the test holes at the Nevada Test Site which had been constructed to test nuclear weapons. In 2011, the cost of testing a NTR and the cost of performing a proof of concept experiment were evaluated.

Report on the environmental and sanitary impacts of the nuclear tests performed by France between 1960 and 1996 and elements of comparison with the tests performed by the other nuclear Powers

International Nuclear Information System (INIS)

Bataille, Ch.; Revol, H.

2002-01-01

This report makes a comprehensive presentation of the French atmospheric and underground nuclear tests performed in Sahara and Polynesia between 1960 and 1996 with their possible impact on the health of populations and personnel and on the environment. A comparison is made with similar tests performed by other nuclear Powers: US (Marshall islands, Nevada), former Soviet union (Semipalatinsk, Novaya Zemlya), UK (several atmospheric test-sites), China, India, Pakistan. (J.S.)

The Oncogenic Fusion Proteins SET-Nup214 and Sequestosome-1 (SQSTM1)-Nup214 Form Dynamic Nuclear Bodies and Differentially Affect Nuclear Protein and Poly(A)+ RNA Export*

Science.gov (United States)

Port, Sarah A.; Mendes, Adélia; Valkova, Christina; Spillner, Christiane; Fahrenkrog, Birthe; Kaether, Christoph; Kehlenbach, Ralph H.

2016-01-01

Genetic rearrangements are a hallmark of several forms of leukemia and can lead to oncogenic fusion proteins. One example of an affected chromosomal region is the gene coding for Nup214, a nucleoporin that localizes to the cytoplasmic side of the nuclear pore complex (NPC). We investigated two such fusion proteins, SET-Nup214 and SQSTM1 (sequestosome)-Nup214, both containing C-terminal portions of Nup214. SET-Nup214 nuclear bodies containing the nuclear export receptor CRM1 were observed in the leukemia cell lines LOUCY and MEGAL. Overexpression of SET-Nup214 in HeLa cells leads to the formation of similar nuclear bodies that recruit CRM1, export cargo proteins, and certain nucleoporins and concomitantly affect nuclear protein and poly(A)+ RNA export. SQSTM1-Nup214, although mostly cytoplasmic, also forms nuclear bodies and inhibits nuclear protein but not poly(A)+ RNA export. The interaction of the fusion proteins with CRM1 is RanGTP-dependent, as shown in co-immunoprecipitation experiments and binding assays. Further analysis revealed that the Nup214 parts mediate the inhibition of nuclear export, whereas the SET or SQSTM1 part determines the localization of the fusion protein and therefore the extent of the effect. SET-Nup214 nuclear bodies are highly mobile structures, which are in equilibrium with the nucleoplasm in interphase and disassemble during mitosis or upon treatment of cells with the CRM1-inhibitor leptomycin B. Strikingly, we found that nucleoporins can be released from nuclear bodies and reintegrated into existing NPC. Our results point to nuclear bodies as a means of preventing the formation of potentially insoluble and harmful protein aggregates that also may serve as storage compartments for nuclear transport factors. PMID:27613868