WorldWideScience

Sample records for focusing dirc fdirc

  1. Design and performance of the focusing DIRC detector

    Energy Technology Data Exchange (ETDEWEB)

    Dey, B. [University of California, Riverside, CA 92521 (United States); Borsato, M.; Arnaud, N. [Laboratoire de l' Accélérateur Linéaire, Centre Scientifique d' Orsay, F-91898 Orsay Cedex (France); Leith, D.W.G.S.; Nishimura, K. [SLAC National Accelerator Laboratory, Stanford, CA 94309 (United States); Roberts, D.A. [University of Maryland, College Park, MD 20742, USA. (United States); Ratcliff, B.N. [SLAC National Accelerator Laboratory, Stanford, CA 94309 (United States); Varner, G. [University of Hawaii, Honolulu, HI 96822, USA. (United States); Va' vra, J., E-mail: jjv@slac.stanford.edu [SLAC National Accelerator Laboratory, Stanford, CA 94309 (United States)

    2015-03-01

    We present the final results from a novel Cherenkov imaging detector called the Focusing DIRC (FDIRC). This detector was designed as a full-scale prototype of the particle identification system for the SuperB experiment [1], and comprises 1/12 of the SuperB barrel azimuthal coverage, with partial photodetector and electronics implementation. The prototype was tested in the SLAC Cosmic Ray Telescope which provided 3D tracking of cosmic muons with an angular resolution of ~1.5 mrad, a position resolution of 4–5 mm, a start time resolution of 70 ps, and muon tracks above ~2 GeV tagged using an iron range stack. The fused silica focusing photon camera was coupled to a full-size BaBar DIRC bar box and was read out, over part of the full coverage, by 12 Hamamatsu H8500 multi-anode photomultipliers (MaPMTs) providing 768 pixels. We used waveform digitizing electronics to read out the MaPMTs. We give a detailed description of our data analysis methods and point out limitations on the present performance. We present results that demonstrate some basic performance characteristics of this design, including (a) single photon Cherenkov angle resolutions with and without chromatic corrections, (b) signal-to-noise (S/N) ratio between the Cherenkov peak and background, which primarily consists of ambiguities of the possible photon paths from emission along the track to a given pixel, (c) dTOP=TOP{sub measured} – TOP{sub expected} resolutions (with TOP being the photon Time-of-Propagation in fused silica), and (d) performance of the detector in the presence of high-rate backgrounds.

  2. Results from the FDIRC prototype

    Energy Technology Data Exchange (ETDEWEB)

    Roberts, D.A., E-mail: roberts@umd.edu [University of Maryland, College Park, MD 20742 (United States); Arnaud, N. [Laboratoire de l’Accélérateur Linéaire, Centre Scientifique d’Orsay, F-91898 Orsay Cedex (France); Dey, B. [University of California, Riverside, CA 92521 (United States); Borsato, M. [Laboratoire de l’Accélérateur Linéaire, Centre Scientifique d’Orsay, F-91898 Orsay Cedex (France); Leith, D.W.G.S.; Nishimura, K.; Ratcliff, B.N. [SLAC, Stanford University, Palo Alto, CA 94309 (United States); Varner, G. [University of Hawaii, Honolulu, HI 96822 (United States); Va’vra, J. [SLAC, Stanford University, Palo Alto, CA 94309 (United States)

    2014-12-01

    We present results from a novel Cherenkov imaging detector called the Focusing DIRC (FDIRC). This detector was designed as a prototype of the particle identification system for the SuperB experiment, and comprises 1/12 of the SuperB barrel azimuthal coverage with partial electronics implementation. The prototype was tested in the SLAC Cosmic Ray Telescope (CRT) which provides 3-D muon tracking with an angular resolution of ∼1.5 mrad, track position resolution of 5–6 mm, start time resolution of 70 ps, and a muon low-energy cutoff of ∼2 GeV provided by an iron range stack. The quartz focusing photon camera couples to a full-size BaBar DIRC bar box and is read out by 12 Hamamatsu H8500 MaPMTs providing 768 pixels. We used IRS2 waveform digitizing electronics to read out the MaPMTs. We present several results from our on-going development activities that demonstrate that the new optics design works very well, including: (a) single photon Cherenkov angle resolutions with and without chromatic corrections, (b) S/N ratio between the Cherenkov peak and background, which consists primarily of ambiguities in possible photon paths to a given pixel, (c) dTOP=TOP{sub measured}–TOP{sub expected} resolutions, and (d) performance of the detector in the presence of high-rate backgrounds. We also describe data analysis methods and point out limits of the present performance. - Highlights: • We present results from a novel Cherenkov imaging detector called the Focusing DIRC (FDIRC). • The prototype was tested in the SLAC Cosmic Ray Telescope (CRT) which provides 3-D muon tracking. • We present several results from our on-going development activities that demonstrate that new optics design works very well. • We describe data analysis methods and point out limits of the present performance.

  3. The PANDA Barrel DIRC

    Science.gov (United States)

    Schwiening, J.; Ali, A.; Belias, A.; Dzhygadlo, R.; Gerhardt, A.; Götzen, K.; Kalicy, G.; Krebs, M.; Lehmann, D.; Nerling, F.; Patsyuk, M.; Peters, K.; Schepers, G.; Schmitt, L.; Schwarz, C.; Traxler, M.; Böhm, M.; Eyrich, W.; Lehmann, A.; Pfaffinger, M.; Uhlig, F.; Düren, M.; Etzelmüller, E.; Föhl, K.; Hayrapetyan, A.; Kreutzfeld, K.; Merle, O.; Rieke, J.; Schmidt, M.; Wasem, T.; Achenbach, P.; Cardinali, M.; Hoek, M.; Lauth, W.; Schlimme, S.; Sfienti, C.; Thiel, M.

    2018-03-01

    The PANDA experiment at the international accelerator Facility for Antiproton and Ion Research in Europe (FAIR) near GSI, Darmstadt, Germany will address fundamental questions of hadron physics. Excellent Particle Identification (PID) over a large range of solid angles and particle momenta will be essential to meet the objectives of the rich physics program. Charged PID for the barrel region of the PANDA target spectrometer will be provided by a DIRC (Detection of Internally Reflected Cherenkov light) detector. The Barrel DIRC will cover the polar angle range of 22o-140o and cleanly separate charged pions from kaons for momenta between 0.5 GeV/c and 3.5 GeV/c with a separation power of at least 3 standard deviations. The design is based on the successful BABAR DIRC and the SuperB FDIRC R&D with several important improvements to optimize the performance for PANDA, such as a focusing lens system, fast timing, a compact fused silica prism as expansion region, and lifetime-enhanced Microchannel-Plate PMTs for photon detection. This article describes the technical design of the PANDA Barrel DIRC and the result of the design validation using a "vertical slice" prototype in hadronic particle beams at the CERN PS.

  4. A detailed study of FDIRC prototype with waveform digitizing electronics in cosmic ray telescope using 3D tracks

    Science.gov (United States)

    Nishimura, K.; Dey, B.; Aston, D.; Leith, D. W. G. S.; Ratcliff, B.; Roberts, D.; Ruckman, L.; Shtol, D.; Varner, G. S.; Va'vra, J.

    2013-02-01

    We present a detailed study of a novel Cherenkov imaging detector called the Focusing DIRC (FDIRC) with waveform digitizing electronics. In this study, the FDIRC prototype has been instrumented with seven Hamamatsu H-8500 MaPMTs. Waveforms from 384 pixels are digitized with waveform sampling electronics based on the BLAB2 ASIC, operating at a sampling speed of ∼2.5 GSa/s. The FDIRC prototype was tested in a large cosmic ray telescope (CRT) providing 3D muon tracks with ∼1.5 mrad angular resolution and muon energy of Emuon> 1.6 GeV. In this study we provide a detailed analysis of the tails in the Cherenkov angle distribution as a function of various variables, compare experimental results with simulation, and identify the major contributions to the tails. We demonstrate that to see the full impact of these tails on the Cherenkov angle resolution, it is crucial to use 3D tracks, and have a full understanding of the role of reconstruction ambiguities. These issues could not be fully explored in previous FDIRC studies where the beam was perpendicular to the quartz radiator bars. This work is relevant for the final FDIRC prototype of the PID detector at SuperB, which will be tested this year in the CRT setup.

  5. A Detailed Study of FDIRC Prototype with Waveform Digitizing Electronics in Cosmic Ray Telescope Using 3D Tracks

    International Nuclear Information System (INIS)

    Nishimura, K.; Dey, B.; Aston, D.; Leith, D.W.G.S.; Ratcliff, B.; Roberts, D.; Ruckman, L.; Shtol, D.; Varner, G.S.; Va'vra, J.

    2012-01-01

    We present a detailed study of a novel Cherenkov imaging detector called the Focusing DIRC (FDIRC) with waveform digitizing electronics. In this test study, the FDIRC prototype has been instrumented with seven Hamamatsu H-8500 MaPMTs. Waveforms from ∼450 pixels are digitized with waveform sampling electronics based on the BLAB2 ASIC, operating at a sampling speed of ∼2.5 GSa/s. The FDIRC prototype was tested in a large cosmic ray telescope (CRT) providing 3D muon tracks with ∼1.5 mrad angular resolution and muon energy of E muon > 1.6 GeV. In this study we provide a detailed analysis of the tails in the Cherenkov angle distribution as a function of various variables, compare experimental results with simulation, and identify the major contributions to the tails. We demonstrate that to see the full impact of these tails on the Cherenkov angle resolution, it is crucial to use 3D tracks, and have a full understanding of the role of ambiguities. These issues could not be fully explored in previous FDIRC studies where the beam was perpendicular to the quartz radiator bars. This work is relevant for the final FDIRC prototype of the PID detector at SuperB, which will be tested this year in the CRT setup.

  6. The GlueX DIRC detector

    Science.gov (United States)

    Barbosa, F.; Bessuille, J.; Chudakov, E.; Dzhygadlo, R.; Fanelli, C.; Frye, J.; Hardin, J.; Kelsey, J.; Patsyuk, M.; Schwarz, C.; Schwiening, J.; Stevens, J.; Shepherd, M.; Whitlatch, T.; Williams, M.

    2017-12-01

    The GlueX DIRC (Detection of Internally Reflected Cherenkov light) detector is being developed to upgrade the particle identification capabilities in the forward region of the GlueX experiment at Jefferson Lab. The GlueX DIRC will utilize four existing decommissioned BaBar DIRC bar boxes, which will be oriented to form a plane roughly 4 m away from the fixed target of the experiment. A new photon camera has been designed that is based on the SuperB FDIRC prototype. The full GlueX DIRC system will consist of two such cameras, with the first planned to be built and installed in 2017. We present the current status of the design and R&D, along with the future plans of the GlueX DIRC detector.

  7. Study of the B"0 → K"*"0e"+e"- decay with the LHCb detector and development of a novel concept of PID detector: the Focusing DIRC

    International Nuclear Information System (INIS)

    Borsato, M.

    2015-01-01

    Flavour-changing neutral current processes of the type b → sγ are forbidden at the tree level in the Standard Model (SM) and occur at leading order through radiative loop diagrams. Therefore, they are sensitive to new physics (NP), which may contribute with competing diagrams. Furthermore, the chirality of the weak interaction in the SM implies that the photon emitted has left-handed polarisation. However, a whole class of NP theories do not share this SM feature and may manifest unambiguously as a right-handed contribution to the polarisation. This thesis presents the first study of the b → sγ photon polarisation through an angular analysis of the B"0 → K"*"0e"+e"- channel. Even though B"0 → K"*"0e"+e"- is not a radiative b → s transition, the contribution from a virtual photon coupling to the lepton pair dominates in the low-q"2 region. Furthermore, the channel with electrons rather than muons allows to better isolate the virtual photon contribution at the low end of the q"2 spectrum. The integrated luminosity of 3 fb"-"1 collected by LHCb during LHC Run 1 allowed for the first time to select a sample of B"0 → K"*"0e"+e"- events large enough to measure the transverse asymmetries A_T"("2") = -0.23±0.23±0.05 and A_T"l"m = 0.14±0.22±0.05 in the low q"2 region between 0.002 GeV"2/c"4 and 1 GeV"2/c"4. These measurements are found to be consistent with SM predictions and provide new constraints on right handed contributions to the photon polarisation at the same level of precision as the one from the average of measurements involving radiative decays made at B-factories. Flavour physics experiments require advanced detectors dedicated to the identification of the different flavours of charged hadrons. Most of them are based on the detection of the Cherenkov light emitted by these particles as they traverse a dielectric medium. This thesis presents also a research/development activity on a new detector concept based on the BABAR DIRC, the FDIRC. Its

  8. The PANDA Barrel DIRC detector

    International Nuclear Information System (INIS)

    Hoek, M.; Dzhygadlo, R.; Gerhardt, A.; Götzen, K.; Hohler, R.; Kalicy, G.; Kumawat, H.; Lehmann, D.; Lewandowski, B.; Patsyuk, M.; Peters, K.; Schepers, G.; Schmitt, L.; Schwarz, C.; Schwiening, J.; Traxler, M.; Zühlsdorf, M.; Dodokhov, V. Kh.; Britting, A.; Eyrich, W.

    2014-01-01

    The PANDA experiment at the new Facility for Antiproton and Ion Research in Europe (FAIR) at GSI, Darmstadt, will study fundamental questions of hadron physics and QCD using high-intensity cooled antiproton beams with momenta between 1.5 and 15 GeV/c. Efficient Particle Identification for a wide momentum range and the full solid angle is required for reconstructing the various physics channels of the PANDA program. Hadronic Particle Identification in the barrel region of the detector will be provided by a DIRC counter. The design is based on the successful BABAR DIRC with important improvements, such as focusing optics and fast photon timing. Several of these improvements, including different radiator geometries and optics, were tested in particle beams at GSI and at CERN. The evolution of the conceptual design of the PANDA Barrel DIRC and the performance of complex prototypes in test beam campaigns will be discussed

  9. The PANDA Barrel DIRC detector

    Energy Technology Data Exchange (ETDEWEB)

    Hoek, M., E-mail: matthias.hoek@uni-mainz.de [Institut für Kernphysik, Johannes Gutenberg University Mainz, Mainz (Germany); Dzhygadlo, R.; Gerhardt, A.; Götzen, K.; Hohler, R.; Kalicy, G.; Kumawat, H.; Lehmann, D.; Lewandowski, B.; Patsyuk, M.; Peters, K.; Schepers, G.; Schmitt, L.; Schwarz, C.; Schwiening, J.; Traxler, M.; Zühlsdorf, M. [GSI Helmholtzzentrum für Schwerionenforschung GmbH, Darmstadt (Germany); Dodokhov, V. Kh. [Joint Institute for Nuclear Research, Dubna (Russian Federation); Britting, A.; Eyrich, W. [Friedrich Alexander-University of Erlangen-Nuremberg, Erlangen (Germany); and others

    2014-12-01

    The PANDA experiment at the new Facility for Antiproton and Ion Research in Europe (FAIR) at GSI, Darmstadt, will study fundamental questions of hadron physics and QCD using high-intensity cooled antiproton beams with momenta between 1.5 and 15 GeV/c. Efficient Particle Identification for a wide momentum range and the full solid angle is required for reconstructing the various physics channels of the PANDA program. Hadronic Particle Identification in the barrel region of the detector will be provided by a DIRC counter. The design is based on the successful BABAR DIRC with important improvements, such as focusing optics and fast photon timing. Several of these improvements, including different radiator geometries and optics, were tested in particle beams at GSI and at CERN. The evolution of the conceptual design of the PANDA Barrel DIRC and the performance of complex prototypes in test beam campaigns will be discussed.

  10. Prototyping the PANDA Barrel DIRC

    Energy Technology Data Exchange (ETDEWEB)

    Schwarz, C., E-mail: C.Schwarz@gsi.de [GSI Helmholtzzentrum für Schwerionenforschung GmbH, Darmstadt (Germany); Kalicy, G.; Dzhygadlo, R.; Gerhardt, A.; Götzen, K.; Hohler, R.; Kumawat, H.; Lehmann, D.; Lewandowski, B.; Patsyuk, M.; Peters, K.; Schepers, G.; Schmitt, L.; Schwiening, J.; Traxler, M.; Zühlsdorf, M. [GSI Helmholtzzentrum für Schwerionenforschung GmbH, Darmstadt (Germany); Dodokhov, V.Kh. [Joint Institute for Nuclear Research, Dubna (Russian Federation); Britting, A.; Eyrich, W.; Lehmann, A. [Friedrich Alexander-University of Erlangen-Nuremberg, Erlangen (Germany); and others

    2014-12-01

    The design of the Barrel DIRC detector for the future PANDA experiment at FAIR contains several important improvements compared to the successful BABAR DIRC, such as focusing and fast timing. To test those improvements as well as other design options a prototype was build and successfully tested in 2012 with particle beams at CERN. The prototype comprises a radiator bar, focusing lens, mirror, and a prism shaped expansion volume made of synthetic fused silica. An array of micro-channel plate photomultiplier tubes measures the location and arrival time of the Cherenkov photons with sub-nanosecond resolution. The development of a fast reconstruction algorithm allowed to tune construction details of the detector setup with test beam data and Monte-Carlo simulations.

  11. Charged Particle ID with DIRCs in PANDA at FAIR

    Energy Technology Data Exchange (ETDEWEB)

    Schepers, Georg [GSI Helmholtzzentrum fuer Schwerionenforschung GmbH, Darmstadt (Germany); Collaboration: PANDA Cherenkov Group of the PANDA-Collaboration

    2015-07-01

    The PANDA detector at FAIR, the new international accelerator facility for antiprotons and ions in Darmstadt, will address open questions of hadronic physics. Experiments concerning charmonium spectroscopy are performed with antiproton beams colliding with hydrogen or nuclear targets. The beam momentum range between 1.5 GeV/c and 15 GeV/c allows tests of the predictions by perturbation theory, but will also reveal deviations originating from strong QCD. Excellent charged particle identification over a large momentum range is necessary for all these experiments. In the target spectrometer this will be accomplished by two Cherenkov counters using the DIRC principle, reducing the size of the solenoid and calorimeter. Both counters have to work in a strong magnetic field and withstand high event rates. The concept of the Barrel DIRC, covering the polar angles between 22 and 140 degrees, is based on the successful BaBar DIRC. It uses focusing optics with lenses and fast photon timing. The Endcap Disc DIRC works with a novel radiator geometry and covers the angular range from 5 to 22 degrees. In addition to a fast electronic readout it employs a compact photon detection system. Prototypes were tested with particle beams at GSI, CERN, DESY, and MAMI to validate the design choices. The results achieved and the status of the PANDA DIRC detectors are presented.

  12. The PANDA Endcap Disc DIRC

    Science.gov (United States)

    Föhl, K.; Ali, A.; Belias, A.; Dzhygadlo, R.; Gerhardt, A.; Götzen, K.; Kalicy, G.; Krebs, M.; Lehmann, D.; Nerling, F.; Patsyuk, M.; Peters, K.; Schepers, G.; Schmitt, L.; Schwarz, C.; Schwiening, J.; Traxler, M.; Böhm, M.; Eyrich, W.; Lehmann, A.; Pfaffinger, M.; Uhlig, F.; Düren, M.; Etzelmüller, E.; Hayrapetyan, A.; Kreutzfeld, K.; Merle, O.; Rieke, J.; Schmidt, M.; Wasem, T.; Achenbach, P.; Cardinali, M.; Hoek, M.; Lauth, W.; Schlimme, S.; Sfienti, C.; Thiel, M.

    2018-02-01

    Positively identifying charged kaons in the PANDA forward endcap solid angle range can be achieved with the Endcap Disc DIRC, allowing kaon-pion separation from 1 up to 4 GeV/c with a separation power of at least 3 standard deviations. Design, performance, and components of this DIRC are given, including the recently introduced TOFPET-ASIC based read-out. Results of a prototype operated in a test beam at DESY in 2016 are shown.

  13. A new prototype for the PANDA disc DIRC detector

    Energy Technology Data Exchange (ETDEWEB)

    Rieke, Julian; Dueren, Michael; Hayrapetyan, Avetik; Foehl, Klaus; Kroeck, Benno; Merle, Oliver; Etzelmueller, Erik; Biguenko, Klim [Justus Liebig Universitaet, Giessen (Germany); Collaboration: PANDA-Collaboration

    2014-07-01

    The PANDA experiment at the future FAIR facility needs excellent particle identification to do precision studies of antiproton-proton reactions in the 1.5-15 GeV/c momentum range. To fulfill this need, two Cherenkov detectors will be installed in the PANDA target spectrometer, both based on the DIRC concept that uses internally reflected Cherenkov light to perform particle identification, with a focus on the separation of pions and kaons. The Disc-DIRC is designed to cap the forward region of theta angles between 5 and 22 degrees. It will be the first time that a 3D-Disc-DIRC is used for PID in a real physics experiment beyond prototyping. A new prototyping Disc-DIRC apparatus has been constructed at the JLU Giessen. Unlike previous prototypes, this one features a radiator as well as focusing elements made out of fused silica. The Cherenkov light is detected with 22 multi-anode-phototubes and 4 MCP-PMTs, totalling 608 individual pixels. Timing information for each of the latter is generated using the novel TRB3 system developed at GSI. The entire prototype was tested with an electron beam of several GeV/c provided by DESY in Hamburg. The components, their setup and a first analysis of the recorded data will be presented.

  14. Prototype test for the PANDA barrel DIRC

    Energy Technology Data Exchange (ETDEWEB)

    Dzhygadlo, Roman; Gerhardt, Andreas; Kalicy, Grzegorz; Krebs, Marvin; Lehmann, Dorothe; Schwarz, Carsten; Schwiening, Jochen; Belias, Anastasios; Traxler, Michael [GSI Helmholtzzentrum fur Schwerionenforschung GmbH, Darmstadt (Germany); Peters, Klaus [GSI Helmholtzzentrum fur Schwerionenforschung GmbH, Darmstadt (Germany); Goethe-Universitaet Frankfurt (Germany); Collaboration: PANDA-Collaboration

    2016-07-01

    The Barrel DIRC (Detector of Internally Reflected Cherenkov light) is designed to provide particle identification (PID) for the PANDA experiment at the new Facility for Antiproton and Ion Research in Europe (FAIR) at GSI, Darmstadt. It is based on the successful BABAR DIRC detector with several key improvements, such as focusing optics, fast timing, and a compact expansion volume. A large prototype was constructed and tested in a hadronic particle beam at CERN during the summer of 2015 to test the PID performance of different design options. The prototype included a fused silica radiator (either a narrow bar or a wide plate), an optional focusing lens, and a prism-shaped fused silica expansion volume. An array of microchannel-plate photomultiplier tubes measured the location and arrival time of the Cherenkov photons on 960 pixels. Data were collected for two radiator geometries and several types of focusing lenses at different beam momenta and polar angles. Results of the analysis as well as a comparison to the Geant4 simulation are presented.

  15. DIRC-based PID for the EIC central detector

    Energy Technology Data Exchange (ETDEWEB)

    Dzhygadlo, Roman; Schwarz, Carsten; Schwiening, Jochen [GSI Helmholtzzentrum fuer Schwerionenforschung GmbH, Darmstadt (Germany); Peters, Klaus [GSI Helmholtzzentrum fuer Schwerionenforschung GmbH, Darmstadt (Germany); Goethe-Universitaet Frankfurt (Germany); Collaboration: DIRC at EIC RD-Collaboration

    2015-07-01

    One of the key requirements for the central detector of a future Electron-Ion Collider (EIC) is to provide radially compact Particle Identification (PID) (e/π,π/K,K/p) over a wide momentum range. It is expected that the PID system will need to include one or more Cherenkov counters to achieve this goal. With a radial size of only a few cm, a DIRC counter (Detector of Internally Reflected Cherenkov light) is potentially an attractive option. The DIRC rate at EIC R and D Collaboration was formed by groups in the United States and Germany in 2011 with funding from DOE to investigate ways to extend the momentum coverage of DIRC counters for the EIC detector by up to 50% beyond the current state of the art. Possible design improvements include a complex focusing system, multi-anode sensors with smaller pixels, a time-based reconstruction algorithm, and chromatic dispersion mitigation. Both Geant and ray-tracing simulations are used to optimize the design configuration of the DIRC counter in terms of the performance and the best integration with the EIC detector. We discuss the current status of the design studies and the possible improvements to the Cherenkov angle resolution and the photon yield.

  16. Performance of the babar-dirc

    International Nuclear Information System (INIS)

    Schwiening, Jochen; Babar-DIRC Collaboration

    2005-01-01

    A new type of ring-imaging Cherenkov detector is being used for hadronic particle identification in the BABAR experiment at the SLAC B Factory (PEP-II). This detector is called DIRC, an acronym for Detection of Internally Reflected Cherenkov (Light). This paper describes the performance of the DIRC during the first 5 years of operation

  17. The PANDA DIRC detectors at FAIR

    Science.gov (United States)

    Schwarz, C.; Ali, A.; Belias, A.; Dzhygadlo, R.; Gerhardt, A.; Götzen, K.; Kalicy, G.; Krebs, M.; Lehmann, D.; Nerling, F.; Patsyuk, M.; Peters, K.; Schepers, G.; Schmitt, L.; Schwiening, J.; Traxler, M.; Zühlsdorf, M.; Böhm, M.; Britting, A.; Eyrich, W.; Lehmann, A.; Pfaffinger, M.; Uhlig, F.; Düren, M.; Etzelmüller, E.; Föhl, K.; Hayrapetyan, A.; Kreutzfeld, K.; Kröck, B.; Merle, O.; Rieke, J.; Schmidt, M.; Wasem, T.; Achenbach, P.; Cardinali, M.; Hoek, M.; Lauth, W.; Schlimme, S.; Sfienti, C.; Thiel, M.; Allison, L.; Hyde, C.

    2017-07-01

    The PANDA detector at the international accelerator Facility for Antiproton and Ion Research in Europe (FAIR) addresses fundamental questions of hadron physics. An excellent hadronic particle identification (PID) will be accomplished by two DIRC (Detection of Internally Reflected Cherenkov light) counters in the target spectrometer. The design for the barrel region covering polar angles between 22o to 140o is based on the successful BABAR DIRC with several key improvements, such as fast photon timing and a compact imaging region. The novel Endcap Disc DIRC will cover the smaller forward angles between 5o (10o) to 22o in the vertical (horizontal) direction. Both DIRC counters will use lifetime-enhanced microchannel plate PMTs for photon detection in combination with fast readout electronics. Geant4 simulations and tests with several prototypes at various beam facilities have been used to evaluate the designs and validate the expected PID performance of both PANDA DIRC counters.

  18. Optical properties of the PANDA barrel DIRC radiator bars

    Energy Technology Data Exchange (ETDEWEB)

    Kalicy, Grzegorz; Krebs, Marvin; Peters, Klaus [GSI, Darmstadt (Germany); Goethe Universitaet, Frankfurt (Germany); Schwarz, Carsten; Schwiening, Jochen [GSI, Darmstadt (Germany); Collaboration: PANDA-Collaboration

    2015-07-01

    The PANDA experiment at the Facility for Antiproton and Ion Research in Europe (FAIR) at GSI, Darmstadt, will study fundamental questions of hadron physics and QCD. A fast focusing DIRC (Detection of Internally Reflected Cherenkov light) counter will provide hadronic particle identification (PID) in the barrel region of the PANDA detector. To meet the PID requirements, the Barrel DIRC has to provide precise measurements of the Cherenkov angle, which is conserved for Cherenkov photons propagating through the radiator by total internal reflection. The radiators, rectangular bars made from fused silica, have to fulfill very strict optical and mechanical requirements. This includes the squareness and parallelism of the sides of the bars, sharp corners, and a very smooth surface polish, ensuring that the Cherenkov photons reach the optical sensors without angular distortions. Currently the Barrel DIRC is at the final design stage and several different bar shapes and fabrication methods are being considered for the final detector. An optical setup, consisting of a computer-controlled positioning and a multi-wavelength laser system, is used to evaluate the radiator bars to obtain critical values like transmittance and reflectivity. The current results and techniques are presented on this poster.

  19. Mechanical design of the WASA DIRC

    Energy Technology Data Exchange (ETDEWEB)

    Bashkanov, M; Clement, H; Doroshkevich, E; Perez del Rio, E Perez; Priking, A; Skorodko, T, E-mail: evd@pit.physik.uni-tuebingen.de [Physikalisches Institute, Eberhardt-Karls-Universitaet Tuebingen, 72076 Tuebingen (Germany)

    2011-10-15

    For precise measurements of the velocity of highly relativistic particles the detection of Cherenkov light is very promising. The Cherenkov rings can be reconstructed from the internally reflected Cherenkov photons detected with position sensitive photomultipliers. DIRC detectors (both in form of a barrel and in form of a disc) are planned to be used in the PANDA detector at FAIR. For the WASA-at-COSY experiment details of the DIRC elements manufacturing and their holding structure are discussed.

  20. DIRC dreams: research directions for the next generation of internally reflected imaging counters

    International Nuclear Information System (INIS)

    Ratcliff, Blair N.; Spanier, Stefan

    1999-01-01

    Some conceptual design features of the total internally reflecting, imaging Cherenkov counter (DIRC) are described. Limits of the DIRC approach to particle identification, and a few features of alternative DIRC designs, are briefly explored

  1. DIRC Dreams Redux: Research Directions for the Next Generation of Internally Reflected Imaging Counters

    Energy Technology Data Exchange (ETDEWEB)

    Ratcliff, Blair N

    2001-09-18

    Some general conceptual design features of total internally reflecting, imaging Cherenkov counters (DIRCs) are described. Limits of the DIRC approach to particle identification and a few features of alternative DIRC designs are briefly explored.

  2. The Endcap Disc DIRC of PANDA

    Science.gov (United States)

    Düren, M.; Etzelmüller, E.; Föhl, K.; Hayrapetyan, A.; Kröck, B.; Merle, O.; Rieke, J.; Schmidt, M.; Wasem, T.; Britting, A.; Eyrich, W.; Lehmann, A.; Pfaffinger, M.; Uhlig, F.; Belias, A.; Dzhygadlo, R.; Gerhardt, A.; Götzen, K.; Kalicy, G.; Krebs, M.; Lehmann, D.; Nerling, F.; Patsyuk, M.; Peters, K.; Schepers, G.; Schmitt, L.; Schwarz, C.; Schwiening, J.; Traxler, M.; Zühlsdorf, M.; Cowie, E.; Keri, T.; Achenbach, P.; Cardinali, M.; Hoek, M.; Lauth, W.; Schlimme, S.; Sfienti, C.; Thiel, M.

    2017-12-01

    The Endcap Disc DIRC (EDD) for PANDA has been designed to identify traversing pions, kaons and protons in the future PANDA experiment. Its central part is a 2 cm thick fused silica plate. Focussing optics are attached to the outer rim of the plate, outside of the acceptance of the experiment. Fast, high-resolution MCP-PMTs, designed to register single Cherenkov photons, have been tested in magnetic field. Filters limit the spectral acceptance of the sensors to reduce dispersion effects and to extend their lifetime. A compact and fast readout is realized with ASICs. Analytical reconstruction algorithms allow for fast particle identification. The angular resolution of a DIRC prototype has been simulated in Monte Carlo and confirmed in a test beam. The final detector will be able to provide a 4 σπ / K separation up to a momentum of 4 GeV / c .

  3. Corrosion of Glass Windows in DIRC PMTs

    Energy Technology Data Exchange (ETDEWEB)

    Va' vra, Jaroslav

    2001-07-27

    The DIRC photon detector contains {approx}11,000 photomultipliers (PMTs), which are submerged in ultra-pure water. This note reports on glass corrosion R and D conducted with PMTs in pure water. We conclude that only limited number ({approx}50) of the PMTs in water are affected by rapid corrosion, while a majority of the 11,000 PMTs should last, according to our measurements, for another ten years. The observation of PMT glass corrosion is based on visual observations, X-ray surface analysis, ESCA surface analysis, weight analysis, transmission measurement, as well as detailed water trace element analysis. We also correlate these observations with DIRC measurements of water pH factor, resistivity, temperature, transmission, and BaBar analysis of Bhabha and di-muon events. We also compare DIRC water purity with that of the Super Kamiokande and K2K experiments, which also use ultra-pure water. We provide empirical proof that corrosion, in our particular Borosilicate type of PMT glass window, occurs at high rate when the glass has no Zn content.

  4. Development and test of a prototype for the PANDA barrel DIRC detector at FAIR

    Energy Technology Data Exchange (ETDEWEB)

    Kalicy, Grzegorz

    2014-07-01

    The PANDA experiment at FAIR will perform world class physics studies using high-intensity cooled antiproton beams with momenta between 1.5 and 15 GeV/c. A rich physics program requires very good particle identification (PID). Charged hadron PID for the barrel section of the target spectrometer has to cover the angular range of 22-140 and separate pions from kaons for momenta up to 3.5 GeV/c with a separation power of at least 3 standard deviations. The system that will provide it has to be thin and operate in a strong magnetic field. A ring imaging Cherenkov detector using the DIRC principle meets those requirements. The design of the PANDA Barrel DIRC is based on the successful BABAR DIRC counter with several important changes to improve the performance and optimize the costs. The design options are being studied in detailed Monte Carlo simulation, and implemented in increasingly complex system prototypes and tested in particle beams. Before building the full system prototypes the radiator bars and lenses are measured on the test benches. The performance of the DIRC prototype was quantified in terms of the single photon Cherenkov angle resolution and the photon yield. Results for two full system prototypes will be presented. The prototype in 2011 aimed at investigating the full size expansion volume. It was found that the resolution for this configuration is at the level of in good agreement with ray tracing simulation results. A more complex prototype, tested in 2012, provided the first experience with a compact fused silica prism expansion volume, a wide radiator plate, and several advanced lens options for the focusing system. The performance of the baseline configuration of the prototype with a standard lens and an air gap met the requirements for the PANDA PID for most of the polar angle range but failed at polar angles around 90 due to photon loss at the air gap. Measurements with a prototype high-refractive index compound lens without an air gap at a polar

  5. Development and test of a prototype for the PANDA barrel DIRC detector at FAIR

    International Nuclear Information System (INIS)

    Kalicy, Grzegorz

    2014-01-01

    The PANDA experiment at FAIR will perform world class physics studies using high-intensity cooled antiproton beams with momenta between 1.5 and 15 GeV/c. A rich physics program requires very good particle identification (PID). Charged hadron PID for the barrel section of the target spectrometer has to cover the angular range of 22-140 and separate pions from kaons for momenta up to 3.5 GeV/c with a separation power of at least 3 standard deviations. The system that will provide it has to be thin and operate in a strong magnetic field. A ring imaging Cherenkov detector using the DIRC principle meets those requirements. The design of the PANDA Barrel DIRC is based on the successful BABAR DIRC counter with several important changes to improve the performance and optimize the costs. The design options are being studied in detailed Monte Carlo simulation, and implemented in increasingly complex system prototypes and tested in particle beams. Before building the full system prototypes the radiator bars and lenses are measured on the test benches. The performance of the DIRC prototype was quantified in terms of the single photon Cherenkov angle resolution and the photon yield. Results for two full system prototypes will be presented. The prototype in 2011 aimed at investigating the full size expansion volume. It was found that the resolution for this configuration is at the level of in good agreement with ray tracing simulation results. A more complex prototype, tested in 2012, provided the first experience with a compact fused silica prism expansion volume, a wide radiator plate, and several advanced lens options for the focusing system. The performance of the baseline configuration of the prototype with a standard lens and an air gap met the requirements for the PANDA PID for most of the polar angle range but failed at polar angles around 90 due to photon loss at the air gap. Measurements with a prototype high-refractive index compound lens without an air gap at a polar

  6. High-performance DIRC detector for the future Electron Ion Collider experiment

    Science.gov (United States)

    Kalicy, G.; Allison, L.; Cao, T.; Dzhygadlo, R.; Hartlove, T.; Horn, T.; Hyde, C.; Ilieva, Y.; Nadel-Turonski, P.; Park, K.; Peters, K.; Schwarz, C.; Schwiening, J.; Stevens, J.; Xi, W.; Zorn, C.

    2018-04-01

    Excellent particle identification (PID) is an essential requirement for a future Electron-Ion Collider (EIC) detector. Identification of the hadrons in the final state is critical to study how different quark flavors contribute to nucleon properties. A detector based on the Detection of Internally Reflected Cherenkov light (DIRC) principle, with a radial size of only a few cm, is a perfect solution for those requirements. The R&D process performed by the EIC PID consortium (eRD14) is focused on designing a high-performance DIRC that would extend the momentum coverage well beyond the state-of-the-art, allowing 3 standard deviations or more separation of π/K up to 6 GeV/c, e/π up to 1.8 GeV/c, and p/K up to 10 GeV/c. A key component to reach such a performance is a special 3-layer compound lens. This article describes the status of the High-Performance DIRC R&D for the EIC detector, with a focus on the detailed Monte Carlo simulation results and performance tests of the 3-layer lens.

  7. Development of DIRC counters for the PANDA experiment at FAIR

    International Nuclear Information System (INIS)

    Seitz, B.; Bettoni, D.; Branford, D.; Britting, A.; Carassiti, V.; Cecchi, A.; Cowie, E.; Dodokhof, V.Kh.; Dueren, M.; Eyrich, W.; Foehl, K.; Hayrapetyan, A.; Hill, G.; Hoek, M.; Hohler, R.; Kaiser, R.; Keri, T.; Lehmann, A.; Lehmann, D.; Marton, J.

    2011-01-01

    The PANDA experiment at the planned FAIR facility at GSI, Darmstadt, aims at measuring hadronic final states with unprecedented precision and luminosity. Superior particle identification of charged and neutral particles is mandatory to fulfil PANDA's physics aims. DIRC (Detection of Internally Reflected Cherenkov light) counters are foreseen for charged particle identification. A barrel DIRC will cover the central region while a disc DIRC will provide particle identification in the forward region. Three DIRC concepts differing in the radiator geometry and method for dispersion correction are studied. The barrel DIRC uses a novel imaging system and aims at exploiting a 3D reconstruction to mitigate dispersion effects. Two concepts are investigated for the forward disc DIRC. One concept employs passive dispersion correction and focussing light guides for image reconstruction. Alternatively, time-of-propagation measurements and a wave-length dependent photon detection system are investigated. The three detector designs share common developments such as investigating radiator properties and photon detection systems, and use the same test beam facilities.

  8. 500 picosecond TDC for DIRC at BABAR

    International Nuclear Information System (INIS)

    Lebbolo, H.; Bailly, P.; Chauveau, J.

    1997-01-01

    A 16 channel TDC chip has been developed at LPNHE Paris, to equip the Front-End electronics of the Detector of Internally Reflected Cerenkov light (DIRC) of the BABAR experiment at the SLAC B factory (Stanford, USA). Binning is 500 picosecond, conversion time is 32 ns, with a fall range of 32 μs. The chip integrates channel buffering and selective readout of data falling within a programmable window defined by the level one trigger latency and resolution. The selective readout allows to manage random inputs at a maximum average rate of 100 kHz on each channel and makes data available at any time a trigger occurs. The maximum average rate of L1 accept trigger will be 2 kHz. The chip, housed in a 68 pin PLCC package, is designed in 0.7 μm CMOS technology and manufactured by ATMEL ES2. The TDC section and channel FIFOs are full custom designs. The TDC uses 16 independent voltage controlled digital delay lines and a 17th calibration channel which allows to tune the delays on the 59.5 MHZ reference clock. The selective readout algorithm has been synthesized from Verilog description and uses ATMEL ES2 standard cells. Die size is 36 mm2 and power less than 100 mW with all inputs fired at 100 kHZ. Prototypes test results show performances better than the specifications for the chip to be used on the DIRC detector. The ten production prototypes have been delivered mid May 1997

  9. Simulation studies for the PANDA endcap disc DIRC

    Energy Technology Data Exchange (ETDEWEB)

    Schmidt, Mustafa; Biguenko, Klim; Dueren, Michael; Hayrapetyan, Avetik; Kroeck, Benno; Merle, Oliver; Rieke, Julian [II. Physikalisches Institut, Justus-Liebig-Universitaet, Giessen (Germany); Foehl, Klaus [CERN, Genf (Switzerland); Collaboration: PANDA-Collaboration

    2015-07-01

    The physics program of the PANDA detector at the future FAIR facility at GSI requires excellent particle identification. For the Panda forward endcap region a novel detector type called ''Disc DIRC'' has been designed. It covers the angular range between 5 and 22 degrees and uses internally reflected Cherenkov light in order to separate pions, kaons and protons up to a momentum of 4 GeV/c. During the design phase, extensive detector simulations have been performed to optimize and evaluate the design. The simulations were done using Geant4 and the PandaRoot framework in addition with a dedicated reconstruction software. An important aspect was the optimization of the imaging while taking the geometrical tolerances of the manufacturing process of the final detector into account. The main focus lies on the optimization process of the cylindrical and polynomial focussing optics at the edges of the detector plate, which has been performed with the merit function of a raytracer called PyOptics, written by one of the group members.

  10. DIRC - a particle identification system for BaBar

    International Nuclear Information System (INIS)

    Hoecker, A.

    1999-10-01

    The DIRC (an acronym for Detection of Internally Reflected Cherenkov light) is a novel type of Cherenkov imaging device that has been developed, built and installed as part of the BaBar detector at the asymmetric B-factory PEP-II at SLAC. The DIRC is based on total internal reflection of Cherenkov photons produced and guided within thin, rectangular quartz bars covering the barrel region of BaBar. The photon detector is an array of photomultiplier tubes covering the photon phase space at the backward end of the bars. In its first few months of operation the DIRC performance has been found to achieve the design requirements. This note presents results from cosmic ray data and an analysis of the first beam collision runs. (author)

  11. DIRC, a new type of particle identification system For BABAR

    International Nuclear Information System (INIS)

    Schwiening, J.

    1997-12-01

    The DIRC, a new type of Cherenkov imaging device, has been selected as the primary particle identification system for the BABAR detector at the asymmetric B-factory, PEP-II. It is based on total internal reflection and uses long, rectangular bars made from synthetic fused silica as Cherenkov radiators and light guides. In this paper, the principles of the DIRC ring imaging Cherenkov technique are explained and results from the prototype program are presented. The studies of the optical properties and radiation hardness of the quartz radiators are described, followed by a discussion of the detector design

  12. DIRC, the internally reflecting ring imaging Cherenkov detector for BABAR

    International Nuclear Information System (INIS)

    Adam, I.; Aston, D.

    1997-11-01

    The DIRC is a new type of Cherenkov imaging device that will be used for the first time in the BABAR detector at the asymmetric B-factory, PEP-II. It is based on total internal reflection and uses long, rectangular bars made from synthetic fused silica as Cherenkov radiator and light guide. The principles of the DIRC ring imaging Cherenkov technique are explained and results from the prototype program are presented. Its choice for the BABAR detector particle identification system is motivated, followed by a discussion of the quartz radiator properties and the detector design

  13. R&D of a high-performance DIRC detector for a future electron-ion collider

    Energy Technology Data Exchange (ETDEWEB)

    Allison, Staceu L. [Old Dominion Univ., Norfolk, VA (United States)

    2017-08-01

    An Electron-Ion Collider (EIC) is proposed as the next big scientific facility to be built in the United States, costing over $1 billion in design and construction. Each detector concept for the electron/ion beam interaction point is integrated into a large solenoidal magnet. The necessity for excellent hadronic particle identification (pion/kaon/proton) in the barrel region of the solenoid has pushed research and development (R&D) towards a new, high-performance Detection of Internally Reflected Cherenkov light (DIRC) detector design. The passage of a high energy charged particle through a fused silica bar of the DIRC generates optical Cherenkov radiation. A large fraction of this light propagates by total internal reflection to the end of the bar, where the photon trajectories expand in a large volume before reaching a highly segmented photo-detector array. The spatial and temporal distribution of the Cherenkov light at the photo-detector array allows one to reconstruct the angle of emission of the light relative to the incident charged particle track. In order to reach the desired performance of 3sigma pi/K separation at 6 GeV/c particle momentum a new 3-layer spherical lens focusing optic with a lanthanum crown glass central layer was designed to have a nearly at focal plane. In order to validate the EIC DIRC simulation package, a synergistic test beam campaign was carried out in 2015 at the CERN PS with the PANDA Barrel DIRC group using a prototype DIRC detector. Along with the analysis of the CERN test beam data, measurements of the focal plane of the 3-layer lens were performed using a custom-built laser setup at Old Dominion University. Radiation hardness of the lanthanum crown glass was tested using a 160 keV X-ray source and a monochromator at the Catholic University of America. Results of these test-bench experiments and the analysis of the 2015 CERN test beam data are presented here.

  14. R&D of a High-Performance DIRC Detector for a Future Electron-Ion Collider

    Science.gov (United States)

    Allison, Stacey Lee

    An Electron-Ion Collider (EIC) is proposed as the next big scientific facility to be built in the United States, costing over $1 billion in design and construction. Each detector concept for the electron/ion beam interaction point is integrated into a large solenoidal magnet. The necessity for excellent hadronic particle identification (pion/kaon/proton) in the barrel region of the solenoid has pushed research and development (R&D) towards a new, high-performance Detection of Internally Reflected Cherenkov light (DIRC) detector design. The passage of a high energy charged particle through a fused silica bar of the DIRC generates optical Cherenkov radiation. A large fraction of this light propagates by total internal reflection to the end of the bar, where the photon trajectories expand in a large volume before reaching a highly segmented photo-detector array. The spatial and temporal distribution of the Cherenkov light at the photo-detector array allows one to reconstruct the angle of emission of the light relative to the incident charged particle track. In order to reach the desired performance of 3sigma pi/K separation at 6 GeV/c particle momentum a new 3-layer spherical lens focusing optic with a lanthanum crown glass central layer was designed to have a nearly flat focal plane. In order to validate the EIC DIRC simulation package, a synergistic test beam campaign was carried out in 2015 at the CERN PS with the PANDA Barrel DIRC group using a prototype DIRC detector. Along with the analysis of the CERN test beam data, measurements of the focal plane of the 3-layer lens were performed using a custom-built laser setup at Old Dominion University. Radiation hardness of the lanthanum crown glass was tested using a 160 keV X-ray source and a monochromator at the Catholic University of America. Results of these test-bench experiments and the analysis of the 2015 CERN test beam data are presented here.

  15. Tests and developments of the PANDA Endcap Disc DIRC

    International Nuclear Information System (INIS)

    Etzelmüller, E.; Belias, A.; Dzhygadlo, R.; Gerhardt, A.; Götzen, K.; Kalicy, G.; Krebs, M.; Lehmann, D.; Nerling, F.; Patsyuk, M.; Peters, K.; Schepers, G.; Schmitt, L.; Schwarz, C.; Schwiening, J.; Traxler, M.; Zühlsdorf, M.; Britting, A.; Eyrich, W.; Lehmann, A.

    2016-01-01

    The PANDA experiment at the future Facility for Antiproton and Ion Research (FAIR) requires excellent particle identification. Two different DIRC detectors will utilize internally reflected Cherenkov light of charged particles to enable the separation of pions and kaons up to momenta of 4 GeV/c. The Endcap Disc DIRC will be placed in the forward endcap of PANDA's central spectrometer covering polar angles between 5° and 22°. Its final design is based on MCP-PMTs for the photon detection and an optical system made of fused silica. A new prototype has been investigated during a test beam at CERN in May 2015 and first results will be presented. In addition a new synthetic fused silica material by Nikon has been tested and was found to be radiation hard.

  16. The DIRC Particle Identification System for the BaBar Experiment

    Energy Technology Data Exchange (ETDEWEB)

    Adam, I

    2004-06-30

    A new type of ring-imaging Cherenkov detector is being used for hadronic particle identification in the BABAR experiment at the SLAC B Factory (PEP-II). This detector is called DIRC, an acronym for Detection of Internally Reflected Cherenkov (Light). This paper will discuss the construction, operation and performance of the BABAR DIRC in detail.

  17. Fabrication of DIRC radiator bars and plates at InSync, Inc.

    Science.gov (United States)

    Tonnessen, T. W.

    2017-12-01

    Fabrication of quality radiator bars and plates is paramount to a successful DIRC project. This write up discusses the trials and tribulations of the manufacture of ~600 bars for the BaBar DIRC project and discusses the history and current capabilities of InSync, Inc.

  18. Developments towards the technical design and prototype evaluation of the anti PANDA Endcap Disc DIRC

    Energy Technology Data Exchange (ETDEWEB)

    Etzelmueller, Erik

    2017-04-15

    The envisaged physics program of the PANDA (antiProton ANnihilation at Darmstadt) experiment at the future Facility for Antiproton and Ion Research (FAIR) requires excellent particle identification over the full solid angle. The Endcap Disc DIRC (EDD) will cover forward polar angles between 5 and 22 and is one of three dedicated subdetectors for the identification of charged hadrons and the separation of pions and kaons in particular. DIRC stands for Detection of Internally Reflected Cherenkov light and implies that the emitted Cherenkov photons are trapped inside the radiator by total internal reflection. The central part of each DIRC detector is its optical system which is responsible for a low-loss and angle-preserving transport of the Cherenkov photons. The work at hand experimentally addresses several objectives in connection with the optical components and the system as a whole. Radiator prototypes were evaluated with high precision and adapted specifications were identified based on the results. The imaging performance of the Focusing Elements (FELs) was verified and different options regarding the coupling of the individual components were evaluated. In addition a radiation hardness study of a new fused silica material provided an insight into the long term behavior of induced defects and confirmed the material to be suitable for high energy physics experiments. A conceptual design for the mechanical integration was developed featuring a rigid optical system which is mounted into a cross-like structure. In this context the spatial constrains for the holding structure and the FELs were identified and an assembly procedure was developed. The existing prototype was revised and newly developed concepts were integrated and tested. Furthermore a data analysis of an earlier prototype test at a mixed hadron beam at CERN was carried out. It was the first evaluation of an EDD prototype which consisted of optical components made of fused silica only and had highly

  19. The DIRC, the particle identification detector of BaBar

    CERN Document Server

    Yéche, C

    1999-01-01

    A novel particle identification detector (PID) has been developed for the BABAR experiment which will operate at the PEP-II B factory at SLAC. The principles of this new concept of PID called the DIRC, based on ring imaging $9 Cherenkov techniques, are briefly described. The results obtained with a large scale prototype and pion, kaon and proton beams at CERN are presented. The performances of this prototype are compared to the Monte-Carlo simulations and $9 the BABAR requirements. (4 refs).

  20. Simulation and reconstruction of photon patterns in the PANDA 3D Disc DIRC

    International Nuclear Information System (INIS)

    Merle, O; Düren, M; Föhl, K; Hayrapetyan, A; Koch, P; Kreutzfeldt, K; Kröck, B; Sporleder, M; Stöckmann, N; Zühlsdorf, M

    2012-01-01

    The PANDA Disc DIRC is a novel type of Cherenkov detector, being developed to improve the charged particle identification of the upcoming PANDA experiment at the future FAIR facility. The detector has to cover the endcap region of the target spectrometer, resulting in a geometry that by now has never been applied to a DIRC detector. Additional complications are implied by tight space constraints at the foreseen position, interaction rates of 20 MHz up to 50 MHz and the experiments trigger-less readout scheme. To cope with the lack of experience, the development of detector concepts is driven by the development of computer simulations and dedicated reconstruction methods. The performance analysis of a preceding detector concept, presented at the DIRC workshop in 2009, showed several weaknesses which have been eliminated by revising the detector design. This publication summarizes the current status of the software, the reconstruction method and resulting detector performance of the improved design: the PANDA 3D Disc DIRC.

  1. The DIRC counter: A new type of particle identification device for B factories

    International Nuclear Information System (INIS)

    Coyle, P.; Lu, A.

    1992-07-01

    A very thin, solid radiator, totally internally reflecting, imaging Cherenkov counter (DIRC) is described. this device is well matched to the hadronic charged particle identification requirements at an asymmetric e + e - B Factory

  2. The DIRC counter: A new type of particle identification device for B factories

    International Nuclear Information System (INIS)

    Ratcliff, B.

    1993-01-01

    A very thin, solid radiator, totally internally reflecting, imaging Cherenkov counter (DIRC) is described. This device is well matched to the hadronic charged particle identification requirements at an asymmetric e + e - B Factory

  3. Testbeam results of the PANDA endcap disc dirc

    Energy Technology Data Exchange (ETDEWEB)

    Etzelmueller, Erik; Biguenko, Klim; Dueren, Michael; Hayrapetyan, Avetik; Rieke, Julian; Schmidt, Mustafa [II. Physikalisches Institut, Justus-Liebig-Universitaet, Giessen (Germany); Collaboration: PANDA-Collaboration

    2016-07-01

    The physics program of the PANDA detector at the future FAIR facility at GSI requires excellent particle identification. For the PANDA forward endcap region a novel detector type called ''Disc DIRC'' has been designed. It covers the angular range between 5 and 22 degrees and uses internally reflected Cherenkov light in order to separate pions, kaons and protons up to a momentum of 4 GeV/c. A new prototype was tested at the PS East Area at CERN in May 2015. For the first time all optical components consisted of fused silica and different MCP-PMT sensors were used for the photon detection. A summary of the analysis will be presented along with results from in-house tests for the individual components.

  4. Particle identification algorithms for the PANDA Endcap Disc DIRC

    Science.gov (United States)

    Schmidt, M.; Ali, A.; Belias, A.; Dzhygadlo, R.; Gerhardt, A.; Götzen, K.; Kalicy, G.; Krebs, M.; Lehmann, D.; Nerling, F.; Patsyuk, M.; Peters, K.; Schepers, G.; Schmitt, L.; Schwarz, C.; Schwiening, J.; Traxler, M.; Böhm, M.; Eyrich, W.; Lehmann, A.; Pfaffinger, M.; Uhlig, F.; Düren, M.; Etzelmüller, E.; Föhl, K.; Hayrapetyan, A.; Kreutzfeld, K.; Merle, O.; Rieke, J.; Wasem, T.; Achenbach, P.; Cardinali, M.; Hoek, M.; Lauth, W.; Schlimme, S.; Sfienti, C.; Thiel, M.

    2017-12-01

    The Endcap Disc DIRC has been developed to provide an excellent particle identification for the future PANDA experiment by separating pions and kaons up to a momentum of 4 GeV/c with a separation power of 3 standard deviations in the polar angle region from 5o to 22o. This goal will be achieved using dedicated particle identification algorithms based on likelihood methods and will be applied in an offline analysis and online event filtering. This paper evaluates the resulting PID performance using Monte-Carlo simulations to study basic single track PID as well as the analysis of complex physics channels. The online reconstruction algorithm has been tested with a Virtex4 FGPA card and optimized regarding the resulting constraints.

  5. Dirc van Delfts Tafel van den Kersten Ghelove en de stervensliteratuur

    DEFF Research Database (Denmark)

    Robbe, Joost Roger

    2015-01-01

    treatise, Dirc van Delft presents a veritable ars moriendi which provides practical guidance for the dying and those attending them. The treatise culminates in a vivid drama in which the soul, being subject to three temptations of the devil, can benefit from the protection of its guardian angel as well...

  6. The barrel and disc DIRC counters for the PANDA experiment at FAIR

    Energy Technology Data Exchange (ETDEWEB)

    Schmidt, Mustafa [II. Physikalisches Institut, Universitaet Giessen (Germany); Collaboration: PANDA-Collaboration

    2016-07-01

    The PANDA spectrometer for the future FAIR facility at GSI will be used to address open questions in hadronic physics by investigating antiproton collisions with a fixed target in the momentum range between 1.5 GeV/c and 15 GeV/c. In order to achieve a particle identification with a high precision, two different DIRC detector concepts have been developed by PANDA, which allow a compact detector design together with an excellent performance to cleanly separate pions, kaons, and protons. The Barrel DIRC in the target spectrometer of PANDA is based on the successful BaBar DIRC with several key improvements. It is designed for polar angles between θ = 22 and θ = 140 and momenta up to 3.5 GeV/c. The Disc DIRC is part of the endcap region of the spectrometer and covers the angular range from θ = 5 /10 to θ = 22 in the forward direction of PANDA. It will provide a π/K separation with a 4-σ separation power up to a momentum of 4 GeV/c. Both Cherenkov detectors will use MCP-PMTs for the photon detection in combination with fast readout electronics. The radiators are synthetic fused silica plates with precision polished surfaces that guarantee to have very little photon losses by total reflection and conserve the Cherenkov angle during propagation through the optical system. Simulations with Geant4 and tests with several prototypes at various test beam facilities have been used to evaluate the designs and validate the expected PID performance of the DIRC counters.

  7. Performance simulation of BaBar DIRC bar boxes in TORCH

    Science.gov (United States)

    Föhl, K.; Brook, N.; Castillo García, L.; Cussans, D.; Forty, R.; Frei, C.; Gao, R.; Gys, T.; Harnew, N.; Piedigrossi, D.; Rademacker, J.; Ros García, A.; van Dijk, M.

    2017-12-01

    TORCH is a large-area precision time-of-flight detector based on the DIRC principle. The DIRC bar boxes of the BaBar experiment at SLAC could possibly be reused to form a part of the TORCH detector time-of-flight wall area, proposed to provide positive particle identification of low momentum kaons in the LHCb experiment at CERN. For a potential integration of BaBar bar boxes into TORCH, new imaging readout optics are required. From the several designs of readout optics that have been considered, two are used in this paper to study the effect of BaBar bar optical imperfections on the detector reconstruction performance. The kaon-pion separation powers obtained from analysing simulated photon hit patterns show the performance reduction for a BaBar bar of non-square geometry compared to a perfectly rectangular cross section.

  8. submitter Performance simulation of BaBar DIRC bar boxes in TORCH

    CERN Document Server

    Föhl, K; Castillo García, L; Cussans, D; Forty, R; Frei, C; Gao, R; Gys, T; Harnew, N; Piedigrossi, D; Rademacker, J; Ros García, A; van Dijk, M

    2017-01-01

    TORCH is a large-area precision time-of-flight detector based on the DIRC principle. The DIRC bar boxes of the BaBar experiment at SLAC could possibly be reused to form a part of the TORCH detector time-of-flight wall area, proposed to provide positive particle identification of low momentum kaons in the LHCb experiment at CERN. For a potential integration of BaBar bar boxes into TORCH, new imaging readout optics are required. From the several designs of readout optics that have been considered, two are used in this paper to study the effect of BaBar bar optical imperfections on the detector reconstruction performance. The kaon-pion separation powers obtained from analysing simulated photon hit patterns show the performance reduction for a BaBar bar of non-square geometry compared to a perfectly rectangular cross section.

  9. Water resistant rhodium plated reflectors for use in the DIRC BaBar Cherenkov detector

    CERN Document Server

    Benkebil, M; Plaszczynski, S; Schune, M H; Wormser, G

    2000-01-01

    Early simulation studies showed that reflectors mounted on the photomultipliers would be useful for the DIRC BaBar Cherenkov detector, showing a gain between 20% and 30% in the number of Cherenkov photons. The proof of principle for these reflectors has been obtained during the beam test of a large-scale prototype of the DIRC detector. An extensive R and D has been conducted in order to test different metallization procedures. Indeed, the challenge was to find a metallization technique which can resist the pure de-ionized water (>15 M OMEGA) up to 10 yr. The chosen technology was rhodium plated reflectors. During the first BaBar cosmic run, the measured performance confirmed the results of the simulation, the prototype-II and the R and D.

  10. Photon counting with a FDIRC Cherenkov prototype readout by SiPM arrays

    Energy Technology Data Exchange (ETDEWEB)

    Marrocchesi, P.S., E-mail: marrocchesi@pi.infn.it [Department of Physical Sciences, Earth and Environment, Via Roma 56, I-53100 Siena (Italy); INFN Sezione di Pisa, Largo Bruno Pontecorvo 3, I-56127 Pisa (Italy); Bagliesi, M.G. [Department of Physical Sciences, Earth and Environment, Via Roma 56, I-53100 Siena (Italy); Basti, A. [Department of Physics, University of Pisa, Largo Bruno Pontecorvo 3, I-56127 Pisa (Italy); INFN Sezione di Pisa, Largo Bruno Pontecorvo 3, I-56127 Pisa (Italy); Bigongiari, G.; Bonechi, S.; Brogi, P. [Department of Physical Sciences, Earth and Environment, Via Roma 56, I-53100 Siena (Italy); INFN Sezione di Pisa, Largo Bruno Pontecorvo 3, I-56127 Pisa (Italy); Checchia, C.; Collazuol, G. [Department of Physics and Astronomy, University of Padova, Padova, Italy, and INFN-Padova, 35131 Padova (Italy); Maestro, P. [Department of Physical Sciences, Earth and Environment, Via Roma 56, I-53100 Siena (Italy); INFN Sezione di Pisa, Largo Bruno Pontecorvo 3, I-56127 Pisa (Italy); Morsani, F. [INFN Sezione di Pisa, Largo Bruno Pontecorvo 3, I-56127 Pisa (Italy); Piemonte, C. [Fondazione Bruno Kessler (FBK), I-38122 Trento (Italy); Stolzi, F.; Suh, J.E; Sulaj, A. [Department of Physical Sciences, Earth and Environment, Via Roma 56, I-53100 Siena (Italy); INFN Sezione di Pisa, Largo Bruno Pontecorvo 3, I-56127 Pisa (Italy)

    2017-02-11

    A prototype of a Focused Internal Reflection Cherenkov, equipped with 16 arrays of NUV-SiPM, was tested at CERN SPS in March 2015 with beams of relativistic ions at 13, 19 and 30 GeV/n obtained from fragmentation of an Ar primary beam. The detector, designed to identify cosmic nuclei, features a Fused Silica radiator bar optically connected to a cylindrical mirror of the same material and an imaging focal plane of dimensions ∼4 cm×3 cm covered with a total of 1024 SiPM photosensors. Thanks to the outstanding performance of the SiPM arrays, the detector could be operated in photon counting mode as a fully digital device. The Cherenkov pattern was recorded together with the total number of detected photoelectrons increasing as Z{sup 2} as a function of the atomic number Z of the beam particle. In this paper, we report on the characterization and test of the SiPM arrays and the performance of the Cherenkov prototype for the charge identification of the beam particles.

  11. In-beam test of a DIRC Cherenkov radiator with SiPM

    International Nuclear Information System (INIS)

    Kroeck, B.; Hayrapetyan, A.; Foehl, K.; Merle, O.; Dueren, M.; Roy, B.J.; Peters, K.

    2009-01-01

    One of the crucial points for any high energy physics experiment is to obtain a good pion/kaon separation i.e. particle identification (PID). For particles in minimum ionising range, the conventional methods of PID using energy loss and time of flight become insufficient. In such a situation, the measurement of velocity of particles using Cherenkov radiation is an effective tool for PID in combination with momentum information from a tracking detector. The PANDA experiment at FAIR/ GSI plans to use a novel technique for PID with detection of internally reflected Cherenkov (DIRC) light. DIRC uses, in contrast to the conventional gas Cherenkov detectors, a solid radiator and total internal reflection to guide Cherenkov photons onto a detection plane where it will be detected by advanced photon counters. A SiPM is a very new generation photon counter that has several advantages over conventional PMTs. Several prototype Cherenkov detectors with different readout systems are being developed for R and D studies. One such prototype detector with Geiger-APD readout has been built at Giessen and was tested in-beam at GSI. The present report provides details of the very first test measurement

  12. Development, design and optimization of a novel endcap DIRC for PANDA

    International Nuclear Information System (INIS)

    Merle, Oliver

    2014-12-01

    PANDA, an experiment at the upcoming FAIR facility in Germany, aims at hadron spectroscopy with high precision and rate by exploiting gluon-rich proton-antiproton collisions at momenta from 1.5 GeV/c to 15 GeV/c. Almost 4π coverage by all detector components is a prerequisite to realize this goal. The objective of this thesis is the system design of a novel type of DIRC Cherenkov detector for particle identification at the forward endcap of the PANDA target spectrometer. A key feature of this detector is its compact, planar design which occupies less than 5 cm in beam direction at the acceptance region (θ<22 ) and ∝20 cm at the outer rim where single-photon imaging cameras are located. After the definition of system requirements, the system has been dissected into individual logical components. For each component, possible hardware and design options have been identified, analyzed and evaluated for compliance with the requirements and their impact on the system performance. The optical system and sensor layout have been optimized to compromise complexity and performance, leading to a highly modular detector setup. The resulting definition of the design comprises the specification of the optical setup, the photosensor and the front-end electronics. Further, a concept for the implementation of the pattern reconstruction algorithm for online reconstruction has been proposed. The novel concept also required the development of dedicated particle identification algorithms which permit the efficient analysis of the measured time-correlated photon patterns. These algorithms have been tested with signals generated by means of time-based Monte Carlo simulations which resemble the time characteristics of the quasi-continuous interaction at the highest rate expected at PANDA. The resulting performance estimations predict a π/K-separation up to 4σ at 4 GeV/c.

  13. The study of CP violation in the B{sup 0} {yields} D{sup +}D{sup -} by means of the BABAR detector. Measurement of the performances of DIRC Cherenkov detector of BABAR: Prototype-II and final detector; L'etude de la violation de CP dans le canal B{sup 0} {yields} D{sup +}D{sup -} a l'aide du detecteur BABAR. La mesure des performances du detecteur Cerenkov DIRC de BABAR: Prototype -II et detecteur final

    Energy Technology Data Exchange (ETDEWEB)

    Benkebil, Mehdi [Lab. de l' Accelerateur Lineaire, Paris-11 Univ., 91 - Orsay (France)

    1999-04-16

    The work presented in this thesis is divided into two parts: the physics analysis of the decay mode B{sup 0} {yields} D{sup +}D{sup -} and the performance obtained with a new type of a particle identification detector using the Cherenkov effect technique: the DIRC. The analysis of this decay mode has been performed with data generated from fast simulation and a preliminary version of the reconstruction program. The branching ratio of this channel is predicted to be 4.5 x 10{sup -4}. The uncertainty in the sin 2 {beta} measurement obtained with this mode is: {sigma}(sin 2{beta})0.19 and 0.32 for fast simulation and preliminary version of the reconstruction program, respectively. The comparison of this result with the one obtained in the B{sup 0} {yields} J/{psi}K{sub s}{sup 0} mode will bring very useful theoretical insights. The performance study of the DIRC has been done on the prototype-II and the final detector. The beam-test results in terms resolution on the {theta}{sub c} angle and number of Cherenkov photons are the following: {sigma}({theta}{sub c}) = 10.2 {+-} 0.1 mrad per photon, {sigma}({theta}{sub c}) = 3.2 {+-} 0.2 mrad per track and N{sub {gamma}} 15.7 {+-} 0.1 at {theta}{sub dip} = 20 angle and 0 transmission in the bar. The analysis of the first cosmic data collected by the BABAR detector has allowed to study the DIRC in its final configuration. Among all the results obtained, we give the following ones: {sigma}({theta}{sub c}) = 10.09 {+-} 0.06 mrad per photon, {sigma}({theta}{sub c}) = 4.71 {+-} 0.14 mrad per track and N{sub {gamma}} 35.2 {+-} 3.8 at {theta}{sub dip} = 20 angle and 0 transmission in the bar. The extrapolation to the real condition of BABAR for all these results shows that the DIRC will run with performances similar to the nominal values. A detailed study of the background shows that, even though it will not be negligible, it will not compromise the DIRC performances in BABAR.

  14. The study of CP violation in the B{sup 0} {yields} D{sup +}D{sup -} by means of the BABAR detector. Measurement of the performances of DIRC Cherenkov detector of BABAR: Prototype-II and final detector; L'etude de la violation de CP dans le canal B{sup 0} {yields} D{sup +}D{sup -} a l'aide du detecteur BABAR. La mesure des performances du detecteur Cerenkov DIRC de BABAR: Prototype -II et detecteur final

    Energy Technology Data Exchange (ETDEWEB)

    Benkebil, Mehdi [Lab. de l' Accelerateur Lineaire, Paris-11 Univ., 91 - Orsay (France)

    1999-04-16

    The work presented in this thesis is divided into two parts: the physics analysis of the decay mode B{sup 0} {yields} D{sup +}D{sup -} and the performance obtained with a new type of a particle identification detector using the Cherenkov effect technique: the DIRC. The analysis of this decay mode has been performed with data generated from fast simulation and a preliminary version of the reconstruction program. The branching ratio of this channel is predicted to be 4.5 x 10{sup -4}. The uncertainty in the sin 2 {beta} measurement obtained with this mode is: {sigma}(sin 2{beta})0.19 and 0.32 for fast simulation and preliminary version of the reconstruction program, respectively. The comparison of this result with the one obtained in the B{sup 0} {yields} J/{psi}K{sub s}{sup 0} mode will bring very useful theoretical insights. The performance study of the DIRC has been done on the prototype-II and the final detector. The beam-test results in terms resolution on the {theta}{sub c} angle and number of Cherenkov photons are the following: {sigma}({theta}{sub c}) = 10.2 {+-} 0.1 mrad per photon, {sigma}({theta}{sub c}) = 3.2 {+-} 0.2 mrad per track and N{sub {gamma}} 15.7 {+-} 0.1 at {theta}{sub dip} = 20 angle and 0 transmission in the bar. The analysis of the first cosmic data collected by the BABAR detector has allowed to study the DIRC in its final configuration. Among all the results obtained, we give the following ones: {sigma}({theta}{sub c}) = 10.09 {+-} 0.06 mrad per photon, {sigma}({theta}{sub c}) = 4.71 {+-} 0.14 mrad per track and N{sub {gamma}} 35.2 {+-} 3.8 at {theta}{sub dip} = 20 angle and 0 transmission in the bar. The extrapolation to the real condition of BABAR for all these results shows that the DIRC will run with performances similar to the nominal values. A detailed study of the background shows that, even though it will not be negligible, it will not compromise the DIRC performances in BABAR.

  15. When the Soul has left the Body: A presentation and analysis of the moment of death within the German version of Dirc van Delft’s Table of Christian Faith

    DEFF Research Database (Denmark)

    Robbe, Joost Roger

    2018-01-01

    This article provides a literary analysis of a 15th-century text, Die sele als sy verscheiden is uitten lichaem (When the soul has left the body), which, until now, remains overlooked and unedited by current scholarship. The text describes what happens to the soul immediately after the moment of ...... Die sele als sy verscheiden is uitten lichaem bears clear testimony to the Late-Medieval shift towards an autonomous approach to death and the need to be the architect of one’s own salvation, as described by the French medievalist and historian Philippe Ariès (1981)....... of physical death and is found in the German version of Dirc van Delft’s Table of Christian Faith. This article discusses the context, function and structure of the text in both its German and (original) Dutch version, and it offers a critical edition and English translation. It concludes by suggesting why...

  16. Focus on focusing

    International Nuclear Information System (INIS)

    Anon.

    1985-01-01

    The discovery and impact of the principle of strong focusing was celebrated at a history Symposium at Stanford on 25 July in the course of the 1985 US Summer School on Particle Accelerators. Burt Richter, Stanford Linac Director, who introduced all the speakers with well chosen reminders about their various contributions related to the theme of the symposium, remarked that it was an appropriate time to be lauding the great contributions of accelerator physicists following the Nobel Prize award to Simon van der Meer for outstanding achievements in accelerator physics

  17. Focus on focusing

    Energy Technology Data Exchange (ETDEWEB)

    Anon.

    1985-10-15

    The discovery and impact of the principle of strong focusing was celebrated at a history Symposium at Stanford on 25 July in the course of the 1985 US Summer School on Particle Accelerators. Burt Richter, Stanford Linac Director, who introduced all the speakers with well chosen reminders about their various contributions related to the theme of the symposium, remarked that it was an appropriate time to be lauding the great contributions of accelerator physicists following the Nobel Prize award to Simon van der Meer for outstanding achievements in accelerator physics.

  18. Focusing ethnography

    DEFF Research Database (Denmark)

    Woermann, Niklas

    2018-01-01

    underpinnings of focusing ethnographic research by comparing different schools of thought and suggesting a practice theory-based approach. It argues that many research projects are focused but do not reflect on the process of focusing, describes how to identify focal settings or practices, and introduces......Building theory with ethnography and filmic research increasingly requires focussing on key practices or settings, instead of painting a broad panorama of a culture. But few authors discuss why and how to focus. This article provides a systematic discussion of the theoretical and methodological...

  19. Study of the $B^0 \\rightarrow K^{\\ast 0}e^+ e^-$ decay with the LHCb detector and development of a novel concept of PID detector: the Focusing DIRC

    CERN Document Server

    AUTHOR|(CDS)2088184; Arnaud, Nicolas

    Flavour-changing neutral current processes of the type $b \\to s\\gamma$ are forbidden at the tree level in the Standard Model (SM) and occur at leading order through radiative loop diagrams. Therefore, they are sensitive to new physics (NP), which may contribute with competing diagrams. Furthermore, the chirality of the weak interaction in the SM implies that the photon emitted has left-handed polarisation. However, a whole class of NP theories do not share this SM feature and may manifest unambiguously as a right-handed contribution to the polarisation. This thesis presents the first study of the ${b}{s\\gamma}$ photon polarisation through an angular analysis of the $B^0 \\rightarrow K^{\\ast 0}e^+ e^-$ channel. Even though $B^0 \\rightarrow K^{\\ast 0}e^+ e^-$ is not a radiative $b\\to s$ transition, the contribution from a virtual photon coupling to the lepton pair dominates in the low-$q^2$ region. Furthermore, the channel with electrons rather than muons allows to better isolate the virtual photon contribution ...

  20. Focused Ethnography

    Directory of Open Access Journals (Sweden)

    Hubert Knoblauch

    2005-09-01

    Full Text Available In this paper I focus on a distinctive kind of sociological ethnography which is particularly, though not exclusively, adopted in applied research. It has been proposed that this branch of ethno­graphy be referred to as focused ethnography. Focused ethnography shall be delineated within the context of other common conceptions of what may be called conventional ethnography. However, rather than being opposed to it, focused ethno­graphy is rather complementary to conventional ethnography, particularly in fields that are charac­teristic of socially and functionally differentiated contemporary society. The paper outlines the back­ground as well as the major methodological features of focused ethnography, such as short-term field visits, data intensity and time intensity, so as to provide a background for future studies in this area. URN: urn:nbn:de:0114-fqs0503440

  1. Without 'Focus'

    Directory of Open Access Journals (Sweden)

    Aldo Sevi

    2010-12-01

    Full Text Available It is widely accepted that a notion of 'focus', more or less as conceived of in Jackendoff (1972, must be incorporated into our theory of grammar, as a means of accounting for certain observed correlations between prosodic facts and semantic/pragmatic facts. In this paper, we put forth the somewhat radical idea that the time has come to give up this customary view, and eliminate 'focus' from our theory of grammar. We argue that such a move is both economical and fruitful.Research over the years has revealed that the correlations between prosody, 'focus', and the alleged semantic/pragmatic effects of focus are much less clear and systematic than we may have initially hoped. First we argue that this state of affairs detracts significantly from the utility of our notion of 'focus', to the point of calling into question the very motivation for including it in the grammar. Then we look at some of the central data, and show how they might be analyzed without recourse to a notion of 'focus'. We concentrate on (i the effect of pitch accent placement on discourse congruence, and (ii the choice of 'associate' for the so-called 'focus sensitive' adverb only. We argue that our focus-free approach to the data improves empirical coverage, and begins to reveal patterns that have previously been obscured by preconceptions about 'focus'.ReferencesBeaver, D. & Clark, B. 2008. Sense and Sensitivity: How Focus Determines Meaning. Blackwell.Beaver, D., Clark, B., Flemming, E., Jaeger, T. F. & Wolters, M. 2007. ‘When semantics meets phonetics: Acoustical studies of second occurrence focus’. Language 83.2: 245–76.http://dx.doi.org/10.1353/lan.2007.0053Beckman, M. & Hirschberg, J. 1994. ‘The ToBI Annotation Conventions’. Ms.,http://www.cs.columbia.edu/~julia/files/conv.pdf.Bolinger, D. 1972. ‘Accent is predictable (if you are a mind-reader’. Language 48.3: 633–44.http://dx.doi.org/10.2307/412039Büring, D. 2006. ‘Focus projection and default

  2. Material focus

    DEFF Research Database (Denmark)

    Sokoler, Tomas; Vallgårda, Anna K. A.

    2009-01-01

    In this paper we build on the notion of computational composites, which hold a material perspective on computational technology. We argue that a focus on the material aspects of the technology could be a fruitful approach to achieve new expressions and to gain a new view on the technology's role...... in design. We study two of the computer's material properties: computed causality and connectability and through developing two computational composites that utilize these properties we begin to explore their potential expressions....

  3. Plasma Focus

    International Nuclear Information System (INIS)

    Bernard, Alain; Jolas, Alain; Garconnet, J.-P.; Mascureau, J. de; Nazet, Christian; Coudeville, Alain; Bekiarian, Andre.

    1977-01-01

    The present report is the edition of the lectures given in a conference on the Focus experiment held at the Centre d'etudes de Limeil, on Oct. 1975. After a survey of the early laboratories one will find the main results obtained in Limeil concerning interferometry, laser scattering, electric and magnetic-measurements, X-ray and neutron emission and also the possible use of explosive current generators instead of capacitor banks at high energy levels. The principal lines of future research are given in the conclusion [fr

  4. Focus: Digital

    DEFF Research Database (Denmark)

    Technology has been an all-important and defining element within the arts throughout the 20th century, and it has fundamentally changed the ways in which we produce and consume music. With this Focus we investigate the latest developments in the digital domain – and their pervasiveness and rapid...... production and reception of contemporary music and sound art. With ‘Digital’ we present four composers' very different answers to how technology impact their work. To Juliana Hodkinson it has become an integral part of her sonic writing. Rudiger Meyer analyses the relationships between art and design and how...

  5. Focusing horn

    CERN Multimedia

    1980-01-01

    This was the first magnetic horn developed by Simon Van der Meer to collect antiprotons in the AD complex. It was used for the AA (antiproton accumulator). Making an antiproton beam took a lot of time and effort. Firstly, protons were accelerated to an energy of 26 GeV/c (protons at 26GeV/c, antiprotons at 3.6GeV/c) in the PS and ejected onto a metal target. From the spray of emerging particles, a magnetic horn picked out 3.6 GeV antiprotons for injection into the AA through a wide-aperture focusing quadrupole magnet. For a million protons hitting the target, just one antiproton was captured, 'cooled' and accumulated. It took 3 days to make a beam of 3 x 10^11 -, three hundred thousand million - antiprotons. The development of this technology was a key step to the functioning of CERN's Super Proton Synchrotron as a proton - antiproton collider.

  6. Plasma focus breeder

    International Nuclear Information System (INIS)

    Ikuta, Kazunari.

    1981-09-01

    Instead of using linear accelerators, it is possible to breed fissile fuels with the help of high current plasma focus device. A mechanism of accelerating proton beam in plasma focus device to high energy would be a change of inductance in plasma column because of rapid growth of plasma instability. A possible scheme of plasma focus breeder is also proposed. (author)

  7. Focused ultrasound in ophthalmology

    Directory of Open Access Journals (Sweden)

    Silverman RH

    2016-09-01

    Full Text Available Ronald H Silverman1,2 1Department of Ophthalmology, Columbia University Medical Center, 2F.L. Lizzi Center for Biomedical Engineering, Riverside Research, New York, NY, USA Abstract: The use of focused ultrasound to obtain diagnostically significant information about the eye goes back to the 1950s. This review describes the historical and technological development of ophthalmic ultrasound and its clinical application and impact. Ultrasound, like light, can be focused, which is crucial for formation of high-resolution, diagnostically useful images. Focused, single-element, mechanically scanned transducers are most common in ophthalmology. Specially designed transducers have been used to generate focused, high-intensity ultrasound that through thermal effects has been used to treat glaucoma (via cilio-destruction, tumors, and other pathologies. Linear and annular transducer arrays offer synthetic focusing in which precise timing of the excitation of independently addressable array elements allows formation of a converging wavefront to create a focus at one or more programmable depths. Most recently, linear array-based plane-wave ultrasound, in which the array emits an unfocused wavefront and focusing is performed solely on received data, has been demonstrated for imaging ocular anatomy and blood flow. While the history of ophthalmic ultrasound extends back over half-a-century, new and powerful technologic advances continue to be made, offering the prospect of novel diagnostic capabilities. Keywords: ophthalmic ultrasound, ultrasound biomicroscopy (UBM, high-intensity focused ultrasound (HIFU, ultrafast imaging, Doppler imaging 

  8. Space Focus Lead Report

    Energy Technology Data Exchange (ETDEWEB)

    Reeves, Geoffrey D. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

    2017-08-10

    The Space Focus team is tasked with the definition of the Space Focused Science Topics, and with the review and ranking of the CSES proposals received in all the program areas. This is achieved by dedicated meetings or a series of informal discussions and/or e-mail reviews.

  9. BrightFocus Foundation

    Science.gov (United States)

    ... About BrightFocus Foundation Featured Content BrightFocus: Investing in Science to Save Mind and Sight We're here to help. Explore ... recognition is very important. Monday, November 6, 2017 New Diagnosis? Managing a mind and sight disease is a journey. And you’ ...

  10. Final focus nomenclature

    International Nuclear Information System (INIS)

    Erickson, R.

    1986-01-01

    The formal names and common names for all devices in the final focus system of the SLC are listed. The formal names consist of a device type designator, microprocessor designator, and a four-digit unit number

  11. Final focus test beam

    International Nuclear Information System (INIS)

    1991-03-01

    This report discusses the following: the Final Focus Test Beam Project; optical design; magnets; instrumentation; magnetic measurement and BPM calibration; mechanical alignment and stabilization; vacuum system; power supplies; control system; radiation shielding and personnel protection; infrastructure; and administration

  12. Facility Focus: Food Service.

    Science.gov (United States)

    College Planning & Management, 2002

    2002-01-01

    Describes the Hawthorn Court Community Center at Iowa State University, Ames, and the HUB-Robeson Center at Pennsylvania State University. Focuses on the food service offered in these new student-life buildings. Includes photographs. (EV)

  13. Focus group discussions

    CERN Document Server

    Hennink, Monique M

    2014-01-01

    The Understanding Research series focuses on the process of writing up social research. The series is broken down into three categories: Understanding Statistics, Understanding Measurement, and Understanding Qualitative Research. The books provide researchers with guides to understanding, writing, and evaluating social research. Each volume demonstrates how research should be represented, including how to write up the methodology as well as the research findings. Each volume also reviews how to appropriately evaluate published research. Focus Group Discussions addresses the challenges associated with conducting and writing focus group research. It provides detailed guidance on the practical and theoretical considerations in conducting focus group discussions including: designing the discussion guide, recruiting participants, training a field team, moderating techniques and ethical considerations. Monique Hennink describes how a methodology section is read and evaluated by others, such as journal reviewers or ...

  14. Final focus nomenclature

    Energy Technology Data Exchange (ETDEWEB)

    Erickson, R.

    1986-08-08

    The formal names and common names for all devices in the final focus system of the SLC are listed. The formal names consist of a device type designator, microprocessor designator, and a four-digit unit number. (LEW)

  15. High harmonics focusing undulator

    Energy Technology Data Exchange (ETDEWEB)

    Varfolomeev, A.A.; Hairetdinov, A.H.; Smirnov, A.V.; Khlebnikov, A.S. [Kurchatov Institute, Moscow (Russian Federation)

    1995-12-31

    It was shown in our previous work that there exist a possibility to enhance significantly the {open_quote}natural{close_quote} focusing properties of the hybrid undulator. Here we analyze the actual undulator configurations which could provide such field structure. Numerical simulations using 2D code PANDIRA were carried out and the enhanced focusing properties of the undulator were demonstrated. The obtained results provide the solution for the beam transport in a very long (short wavelength) undulator schemes.

  16. The Individually Focused Interview

    DEFF Research Database (Denmark)

    Clausen, Aksel Skovgaard

    2012-01-01

    relatively “strong” interviewees (interview persons: IPs) with diverse backgrounds; (2) thorough planning of the interview with well-focused themes; and (3) a thorough and repeated introduction to the interview. The omission of audio transcriptions is an obvious solution to the researcher who wants a breadth...... of range of statements stemming from the use of many more interviewees than is often possible. The Individually Focused Interview (TIFI) also provides more time for involvement in the field and further analysis....

  17. Plutonium focus area

    International Nuclear Information System (INIS)

    1996-08-01

    To ensure research and development programs focus on the most pressing environmental restoration and waste management problems at the U.S. Department of Energy (DOE), the Assistant Secretary for the Office of Environmental Management (EM) established a working group in August 1993 to implement a new approach to research and technology development. As part of this new approach, EM developed a management structure and principles that led to the creation of specific Focus Areas. These organizations were designed to focus the scientific and technical talent throughout DOE and the national scientific community on the major environmental restoration and waste management problems facing DOE. The Focus Area approach provides the framework for intersite cooperation and leveraging of resources on common problems. After the original establishment of five major Focus Areas within the Office of Technology Development (EM-50, now called the Office of Science and Technology), the Nuclear Materials Stabilization Task Group (EM-66) followed the structure already in place in EM-50 and chartered the Plutonium Focus Area (PFA). The following information outlines the scope and mission of the EM, EM-60, and EM-66 organizations as related to the PFA organizational structure

  18. Plasma focus matching conditions

    International Nuclear Information System (INIS)

    Soliman, H.M.; Masoud, M.M.; Elkhalafawy, T.A.

    1988-01-01

    A snow-plough and slug models have been used to obtain the optimum matching conditions of the plasma in the focus. The dimensions of the plasma focus device are, inner electrode radius = 2 cm, outer electrode radius = 5.5 cm, and its length = 8 cm. It was found that the maximum magnetic energy of 12.26 kJ has to be delivered to plasma focus whose density is 10 19 /cm 3 at focusing time of 2.55 μs and with total external inductance of 24.2 n H. The same method is used to evaluate the optimum matching conditions for the previous coaxial discharge system which had inner electrode radius = 1.6 cm, outer electrode radius = 3.3 cm and its length = 31.5 cm. These conditions are charging voltage = 12 kV, capacity of the condenser bank = 430 μf, plasma focus density = 10 19 /cm 3 focusing time = 8 μs and total external inductance = 60.32 n H.3 fig., 2 tab

  19. The focus factor

    DEFF Research Database (Denmark)

    Nicolaisen, Jeppe; Frandsen, Tove Faber

    2015-01-01

    Introduction. We present a new bibliometric indicator to measure journal specialisation over time, named the focus factor. This new indicator is based on bibliographic coupling and counts the percentage of re-citations given in subsequent years. Method. The applicability of the new indicator....... To validate re-citations as caused by specialisation, other possible causes were measured and correlated (obsolescence, journal self-citations and number of references). Results. The results indicate that the focus factor is capable of distinguishing between general and specialised journals and thus...... effectively measures the intended phenomenon (i.e., journal specialisation). Only weak correlations were found between journal re-citations and obsolescence, journal self-citations, and number of references. Conclusions. The focus factor successfully measures journal specialisation over time. Measures based...

  20. Decontamination & decommissioning focus area

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-08-01

    In January 1994, the US Department of Energy Office of Environmental Management (DOE EM) formally introduced its new approach to managing DOE`s environmental research and technology development activities. The goal of the new approach is to conduct research and development in critical areas of interest to DOE, utilizing the best talent in the Department and in the national science community. To facilitate this solutions-oriented approach, the Office of Science and Technology (EM-50, formerly the Office of Technology Development) formed five Focus AReas to stimulate the required basic research, development, and demonstration efforts to seek new, innovative cleanup methods. In February 1995, EM-50 selected the DOE Morgantown Energy Technology Center (METC) to lead implementation of one of these Focus Areas: the Decontamination and Decommissioning (D & D) Focus Area.

  1. Collective focusing ion accelerator

    International Nuclear Information System (INIS)

    Goldin, F.J.

    1986-01-01

    The principal subject of this dissertation is the trapping confinement of pure electron plasmas in bumpy toroidal magnetic fields, with particular attention given to the trapping procedure and the behavior of the plasma during the final equilibrium. The most important aspects of the equilibrium studied were the qualitative nature of the plasma configuration and motion and its density, distribution and stability. The motivation for this study was that an unneutralized cloud of electrons contained in a toroidal system, sufficiently dense and stable, may serve to electrostatically focus ions (against centrifugal and self space charge forces) in a cyclic ion accelerator. Such an accelerator, known as a Collective Focusing Ion Accelerator (CFIA) could be far smaller than conventional designs (which use external magnetic fields directly to focus the ions) due to the smaller gyro-radium of an electron in a magnetic field of given strength. The electron cloud generally drifted poloidally at a finite radius from the toroidal minor axis. As this would preclude focusing ions with such clouds, damping this motion was investigated. Finite resistance in the normally perfectly conductive vessel wall did this. In further preparation for a working CFIA, additional experiments studied the effect of ions on the stability of the electron cloud

  2. Plasma focus project

    International Nuclear Information System (INIS)

    Sahlin, H.L.

    1975-12-01

    The primary objective of this project is to provide a relatively simple pulsed power source for high density pulsed fusion studies with a variety of DT and other fusion microexplosion targets. The plasma focus operated on DT at 1 MJ should produce greater than or equal to 10 15 DT neutrons per pulse corresponding to 2800 J of nuclear energy release and for low pressure operation and appropriately configured high Z anode center should yield an x-ray burst of about 1000 J with a substantial fraction of this x-ray energy concentrated in the 5-100 kV range. Because of its x-ray and neutron production potential, the operation of the focus as an x-ray source is also under study and an initial design study for a repetitively pulsed 1 MJ plasma focus as a pulsed neutron materials testing source has been completed. The plasma focus seems particularly appropriate for application as a materials testing source for pulsed fusion reactors, for example, based on laser driven fusion microexplosions. The construction status of the device is described

  3. Focusing of electromagnetic waves

    International Nuclear Information System (INIS)

    Dhayalan, V.

    1996-01-01

    The focusing of electromagnetic waves inside a slab has been examined together with two special cases in which the slab is reduced to a single interface or a single medium. To that end the exact solutions for the fields inside a layered medium have been used, given in terms of the outside current source in order to obtain the solutions for the focused electric field inside a slab. Both exact and asymptotic solutions of the problem have been considered, and the validity of the latter has been discussed. The author has developed a numerical algorithm for evaluation of the diffraction integral with special emphasis on reducing the computing time. The numerical techniques in the paper can be readily applied to evaluate similar diffraction integrals occurring e.g. in microstrip antennas. 46 refs

  4. Magnetic Focusing Horn

    CERN Multimedia

    1974-01-01

    This magnetic focusing horn was used for the AA (antiproton accumulator). Its development was an important step towards using CERN's Super Proton Synchrotron as a proton - antiproton collider. This eventually led to the discovery of the W and Z particles in 1983. Making an antiproton beam took a lot of time and effort. Firstly, protons were accelerated to an energy of 26 GeV in the PS and ejected onto a metal target. From the spray of emerging particles, a magnetic horn picked out 3.6 GeV antiprotons for injection into the AA through a wide-aperture focusing quadrupole magnet. For a million protons hitting the target, just one antiproton was captured, 'cooled' and accumulated. It took 3 days to make a beam of 3 x 10^11 -, three hundred thousand million - antiprotons.

  5. An adiabatic focuser

    International Nuclear Information System (INIS)

    Chen, P.; Oide, K.; Sessler, A.M.; Yu, S.S.

    1989-08-01

    Theoretical analysis is made of an intense relativistic electron beam, such as would be available from a linear collider, moving through a plasma of increasing density, but density always less than that of the beam (underdense). In this situation, the plasma electrons are expelled from the beam channel and the electrons are subject to an ever-increasing focusing force provided by the channel ions. Analysis is made on the beam radiation energy loss in the classical, the transition, and the quantum regimes. It is shown that the focuser is insensitive to the beam energy spread behaviors in the nonclassical regimes, the radiation limit on lenses (the Oide limit) can be exceeded. The sensitivity of the system to the topic mismatch and the nonlinearity is also analyzed. Examples are given with SLC-type and TLC-type parameters. 9 refs., 1 tab

  6. Line broadening by focusing

    International Nuclear Information System (INIS)

    Brito, A.L. de; Jabs, A.

    1983-01-01

    It is pointed out that the spectral width of a quasi-monochromatic light beam broadens when the beam is focused. A quantitative formula for this broadening is derived from classical wave theory. The effect is shown to explain some experiments on laser beams done by E. Panarella which that author has explained under the ad-hoc hypothesis that the frequency of the photons changes along with the intensity of the light beam. The line broadening by focusing might also contribute to gas ionization by incident light when the ionization potential is well above the mean photon energy. Some remarks are made on some direct applications of the Heisenberg relations in comparison with our treatment. (Author) [pt

  7. Focus on Delivery

    DEFF Research Database (Denmark)

    Hasman, Kirsten; Barfoed, Anne

    Background: Compared to other Nordic countries, Denmark has a high incidence of anal sphincter injury. Recent studies indicate that a strict focus on prevention of severe perineal trauma has decreased the incidence (1). This has resulted in changed clinical procedures in several Danish labour wards...... (2). It is, however, not clarified which of the multifaceted aspects of preventing perineal injury that might explain the decrease (3). Aims: We hypothesized that the use of structured reflection on a clinical practice by midwives and midwifery students would increase both parts’ knowledge on how...... attended the delivery, facilitated the midwife’s and the student’s structured reflection. Further, the project midwife held daily simulation workshops with midwives and students. Two focus group interviews with students and midwives were conducted and analyzed using content analysis. Results and conclusion...

  8. Focus Group Guide

    Science.gov (United States)

    2017-07-01

    home for the arrival of school- aged children. TIP: Do not conduct focus groups in a command conference room in the command group area. Doing so...organizational effectiveness and equal opportunity/equal employment opportunity/fair treatment and sexual assault and response factors (which are listed on the... Sexual Harassment (C) Sex Harassment Retaliation (D) Discrimination - Sex (E) Discrimination - Race (F) Discrimination - Disability (G

  9. Dialogicality in Focus

    DEFF Research Database (Denmark)

    The phenomenon which dialogism addresses is human interaction. It enables us to conceptualise human interaction as intersubjective, symbolic, cultural, transformative and conflictual, in short, as complex. The complexity of human interaction is evident in all domains of human life, for example, i......, because rather than applying dialogism to this or that domain, the present volume focuses on dialogicality itself to interrogate the concepts and methods which are taken for granted in the burgeoning literature. (Imprint: Nova Press)...

  10. Dense Plasma Focus Modeling

    Energy Technology Data Exchange (ETDEWEB)

    Li, Hui [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Li, Shengtai [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Jungman, Gerard [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Hayes-Sterbenz, Anna Catherine [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

    2016-08-31

    The mechanisms for pinch formation in Dense Plasma Focus (DPF) devices, with the generation of high-energy ions beams and subsequent neutron production over a relatively short distance, are not fully understood. Here we report on high-fidelity 2D and 3D numerical magnetohydrodynamic (MHD) simulations using the LA-COMPASS code to study the pinch formation dynamics and its associated instabilities and neutron production.

  11. Subsurface contaminants focus area

    International Nuclear Information System (INIS)

    1996-08-01

    The US Department of Enregy (DOE) Subsurface Contaminants Focus Area is developing technologies to address environmental problems associated with hazardous and radioactive contaminants in soil and groundwater that exist throughout the DOE complex, including radionuclides, heavy metals; and dense non-aqueous phase liquids (DNAPLs). More than 5,700 known DOE groundwater plumes have contaminated over 600 billion gallons of water and 200 million cubic meters of soil. Migration of these plumes threatens local and regional water sources, and in some cases has already adversely impacted off-site rsources. In addition, the Subsurface Contaminants Focus Area is responsible for supplying technologies for the remediation of numerous landfills at DOE facilities. These landfills are estimated to contain over 3 million cubic meters of radioactive and hazardous buried Technology developed within this specialty area will provide efective methods to contain contaminant plumes and new or alternative technologies for development of in situ technologies to minimize waste disposal costs and potential worker exposure by treating plumes in place. While addressing contaminant plumes emanating from DOE landfills, the Subsurface Contaminants Focus Area is also working to develop new or alternative technologies for the in situ stabilization, and nonintrusive characterization of these disposal sites

  12. Particle Accelerator Focus Automation

    Science.gov (United States)

    Lopes, José; Rocha, Jorge; Redondo, Luís; Cruz, João

    2017-08-01

    The Laboratório de Aceleradores e Tecnologias de Radiação (LATR) at the Campus Tecnológico e Nuclear, of Instituto Superior Técnico (IST) has a horizontal electrostatic particle accelerator based on the Van de Graaff machine which is used for research in the area of material characterization. This machine produces alfa (He+) and proton (H+) beams of some μA currents up to 2 MeV/q energies. Beam focusing is obtained using a cylindrical lens of the Einzel type, assembled near the high voltage terminal. This paper describes the developed system that automatically focuses the ion beam, using a personal computer running the LabVIEW software, a multifunction input/output board and signal conditioning circuits. The focusing procedure consists of a scanning method to find the lens bias voltage which maximizes the beam current measured on a beam stopper target, which is used as feedback for the scanning cycle. This system, as part of a wider start up and shut down automation system built for this particle accelerator, brings great advantages to the operation of the accelerator by turning it faster and easier to operate, requiring less human presence, and adding the possibility of total remote control in safe conditions.

  13. Particle Accelerator Focus Automation

    Directory of Open Access Journals (Sweden)

    Lopes José

    2017-08-01

    Full Text Available The Laboratório de Aceleradores e Tecnologias de Radiação (LATR at the Campus Tecnológico e Nuclear, of Instituto Superior Técnico (IST has a horizontal electrostatic particle accelerator based on the Van de Graaff machine which is used for research in the area of material characterization. This machine produces alfa (He+ and proton (H+ beams of some μA currents up to 2 MeV/q energies. Beam focusing is obtained using a cylindrical lens of the Einzel type, assembled near the high voltage terminal. This paper describes the developed system that automatically focuses the ion beam, using a personal computer running the LabVIEW software, a multifunction input/output board and signal conditioning circuits. The focusing procedure consists of a scanning method to find the lens bias voltage which maximizes the beam current measured on a beam stopper target, which is used as feedback for the scanning cycle. This system, as part of a wider start up and shut down automation system built for this particle accelerator, brings great advantages to the operation of the accelerator by turning it faster and easier to operate, requiring less human presence, and adding the possibility of total remote control in safe conditions.

  14. Subsurface contaminants focus area

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-08-01

    The US Department of Enregy (DOE) Subsurface Contaminants Focus Area is developing technologies to address environmental problems associated with hazardous and radioactive contaminants in soil and groundwater that exist throughout the DOE complex, including radionuclides, heavy metals; and dense non-aqueous phase liquids (DNAPLs). More than 5,700 known DOE groundwater plumes have contaminated over 600 billion gallons of water and 200 million cubic meters of soil. Migration of these plumes threatens local and regional water sources, and in some cases has already adversely impacted off-site rsources. In addition, the Subsurface Contaminants Focus Area is responsible for supplying technologies for the remediation of numerous landfills at DOE facilities. These landfills are estimated to contain over 3 million cubic meters of radioactive and hazardous buried Technology developed within this specialty area will provide efective methods to contain contaminant plumes and new or alternative technologies for development of in situ technologies to minimize waste disposal costs and potential worker exposure by treating plumes in place. While addressing contaminant plumes emanating from DOE landfills, the Subsurface Contaminants Focus Area is also working to develop new or alternative technologies for the in situ stabilization, and nonintrusive characterization of these disposal sites.

  15. Focus on Russia

    International Nuclear Information System (INIS)

    Van Koningsbrugge, H.

    2008-01-01

    A few articles in this magazine focus on the developments and policies in Russia. The titles of some of the articles are 'Between state power and liberal reform' on the task of the new Russian president to find a new balance between government interference and market economy; 'Green light for green energy' on the willingness of the Russian government to stimulate renewable energy; 'Russian power play' on the role of Gazprom in the liberalization of the Russian power market; 'Gazprom's risky strategy' on it's pricing strategy

  16. Focus on Organic Conductors

    Directory of Open Access Journals (Sweden)

    Shinya Uji, Takehiko Mori and Toshihiro Takahashi

    2009-01-01

    Full Text Available Organic materials are usually thought of as electrical insulators. Progress in chemical synthesis, however, has brought us a rich variety of conducting organic materials, which can be classified into conducting polymers and molecular crystals. Researchers can realize highly conducting molecular crystals in charge-transfer complexes, where suitable combinations of organic electron donor or acceptor molecules with counter ions or other organic molecules provide charge carriers. By means of a kind of chemical doping, the charge-transfer complexes exhibit high electrical conductivity and, thanks to their highly crystalline nature, even superconductivity has been observed. This focus issue of Science and Technology of Advanced Materials is devoted to the research into such 'organic conductors'The first organic metal was (TTF(TCNQ, which was found in 1973 to have high conductivity at room temperature and a metal–insulator transition at low temperatures. The first organic superconductor was (TMTSF2PF6, whose superconductivity under high pressures was reported by J´erome in 1980. After these findings, the research on organic conductors exploded. Hundreds of organic conductors have been reported, among which more than one hundred exhibit superconductivity. Recently, a single-component organic conductor has been found with metallic conductivity down to low temperatures.In these organic conductors, in spite of their simple electronic structures, much new physics has arisen from the low dimensionality. Examples are charge and spin density waves, characteristic metal–insulator transitions, charge order, unconventional superconductivity, superconductor–insulator transitions, and zero-gap conductors with Dirac cones. The discovery of this new physics is undoubtedly derived from the development of many intriguing novel organic conductors. High quality single crystals are indispensable to the precise measurement of electronic states.This focus issue

  17. Rheological phenomena in focus

    CERN Document Server

    Boger, DV

    1993-01-01

    More than possibly any other scientific discipline, rheology is easily visualized and the relevant literature contains many excellent photographs of unusual and often bizarre phenomena. The present book brings together these photographs for the first time. They are supported by a full explanatory text. Rheological Phenomena in Focus will be an indispensable support manual to all those who teach rheology or have to convince colleagues of the practical relevance of the subject within an industrial setting. For those who teach fluid mechanics, the book clearly illustrates the difference be

  18. Focused detection logging technique

    International Nuclear Information System (INIS)

    Turcotte, R.E.

    1977-01-01

    In accordance with an illustrative embodiment of the present invention, a method and apparatus is disclosed for determining a characteristic of the media surrounding a borehole by emitting gamma radiation in at least one tightly collimated beam toward an earth formation adjacent a borehole, by detecting from a plurality of tightly collimated paths that are focused at a zone of intersection with and aligned to intersect with each emitted beam the gamma radiation scattered by the interaction of the emitted gamma radiation and the media at the zones of intersection, by misaligning the emitted beams and the tightly collimated paths to prevent their intersection, by detecting gamma radiation scattered by the interaction of the emitted gamma radiation and the media with the emitted beams and the tightly collimated paths misaligned and by determining from the detected gamma radiation a media characteristic. In one embodiment, the detection collimater used is formed of a material that is essentially opaque to gamma radiation at the energies of interest and includes a plurality of passageways that are spherically focused at a zone of intersection with one of the emitted beams of gamma radiation and that are arranged in a number of surfaces that are curved to be azimuthally symmetrical about the axis of the intersected beam. 14 figures

  19. Doing focus group research

    DEFF Research Database (Denmark)

    Lindegaard, Laura Bang

    2014-01-01

    Scholars of ethnomethodologically informed discourse studies are often sceptical of the use of interview data such as focus group data. Some scholars quite simply reject interview data with reference to a general preference for so-called naturally occurring data. Other scholars acknowledge...... that interview data can be of some use if the distinction between natural and contrived data is given up and replaced with a distinction between interview data as topic or as resource. In greater detail, such scholars argue that interview data are perfectly adequate if the researcher wants to study the topic...... of interview interaction, but inadequate as data for studying phenomena that go beyond the phenomenon of interview interaction. Neither of these more and less sceptical positions are, on the face of it, surprising due to the ethnomethodological commitment to study social order as accomplished in situ...

  20. Focus on Succes

    Directory of Open Access Journals (Sweden)

    Ivan Slimák

    2011-10-01

    Full Text Available The Editor wishes to present the need and form of turning the focus of individuals and organisations to success, based on evaluating understanding of the situation, on complex improving the quality of work, production and life, and on awareness of accountability for consequences of one’s actions in the given environment and time. Understood by success is sustained financial and non-financial prosperity, whilst decisive is the evaluating process, the key element is loyalty of natural and physical persons, and the priority is loyalty of external customers. The address is targeted to would-be authors and readers of our Journal interested in engineering and management of quality of mutually correlate entities.

  1. Cosmological Final Focus Systems

    International Nuclear Information System (INIS)

    Irwin, J

    2004-01-01

    We develop the many striking parallels between the dynamics of light streams from distant galaxies and particle beams in accelerator final focus systems. Notably the deflections of light by mass clumps are identical to the kicks arising from the long-range beam-beam interactions of two counter-rotating particle beams (known as parasitic crossings). These deflections have sextupolar as well as quadrupolar components. We estimate the strength of such distortions for a variety of circumstances and argue that the sextupolar distortions from clumping within clusters may be observable. This possibility is enhanced by the facts that (1) the sextupolar distortions of background galaxies is a factor of 5 smaller than the quadrupolar distortion, (2) the angular orientation of the sextupolar and quadrupolar distortions from a mass distribution would be correlated, appearing as a slightly curved image, (3) these effects should be spatially clumped on the sky

  2. The FOCUS trial

    DEFF Research Database (Denmark)

    Glenthøj, Louise B; Fagerlund, Birgitte; Randers, Lasse

    2015-01-01

    BACKGROUND: Cognitive deficits are a distinct feature among people at ultra-high risk (UHR) for psychosis and pose a barrier to functional recovery. Insufficient evidence exists on how to ameliorate these cognitive deficits in patients at UHR for psychosis and hence improve daily living and quality...... of life. The aim of the trial is to investigate whether cognitive remediation can improve cognitive and psychosocial function in patients at UHR for psychosis. METHODS: The FOCUS trial (Function and Overall Cognition in Ultra-high risk States) is a randomised, parallel group, observer-blinded clinical...... trial enrolling 126 patients meeting the standardised criteria of being at UHR for psychosis. Patients are recruited from psychiatric in- and outpatient facilities in the Copenhagen catchment area. Patients are randomised to one of the two treatment arms: cognitive remediation plus standard treatment...

  3. Focusing on customer service.

    Science.gov (United States)

    1996-01-01

    This booklet is devoted to a consideration of how good customer service in family planning programs can generate demand for products and services, bring customers back, and reduce costs. Customer service is defined as increasing client satisfaction through continuous concern for client preferences, staff accountability to clients, and respect for the rights of clients. Issues discussed include the introduction of a customer service approach and gaining staff commitment. The experience of PROSALUD in Bolivia in recruiting appropriate staff, supervising staff, soliciting client feedback, and marketing services is offered as an example of a successful customer service approach. The key customer service functions are described as 1) establishing a welcoming atmosphere, 2) streamlining client flow, 3) personalizing client services, and 4) organizing and providing clear information to clients. The role of the manager in developing procedures is explored, and the COPE (Client-Oriented Provider-Efficient) process is presented as a good way to begin to make improvements. Techniques in staff training in customer service include brainstorming, role playing, using case studies (examples of which are provided), and engaging in practice sessions. Training also leads to the development of effective customer service attitudes, and the differences between these and organizational/staff-focused attitudes are illustrated in a chart. The use of communication skills (asking open-ended questions, helping clients express their concerns, engaging in active listening, and handling difficult situations) is considered. Good recovery skills are important when things go wrong. Gathering and using client feedback is the next topic considered. This involves identifying, recording, and discussing customer service issues as well as taking action on these issues and evaluating the results. The booklet ends by providing a sample of customer service indicators, considering the maintenance of a

  4. FOCUS ON GRAPHENE

    International Nuclear Information System (INIS)

    Peres, N M R; Ribeiro, Ricardo M

    2009-01-01

    Graphene physics is currently one of the most active research areas in condensed matter physics. Countless theoretical and experimental studies have already been performed, targeting electronic, magnetic, thermal, optical, structural and vibrational properties. Also, studies that modify pristine graphene, aiming at finding new physics and possible new applications, have been considered. These include patterning nanoribbons and quantum dots, exposing graphene's surface to different chemical species, studying multilayer systems, and inducing strain and curvature (modifying in this way graphene's electronic properties). This focus issue includes many of the latest developments on graphene research. Focus on Graphene Contents The effect of sublattice symmetry breaking on the electronic properties of doped graphene A Qaiumzadeh and R Asgari Interfaces within graphene nanoribbons J Wurm, M Wimmer, I Adagideli, K Richter and H U Baranger Weak localization and transport gap in graphene antidot lattices J Eroms and D Weiss Electronic properties of graphene antidot lattices J A Fuerst, J G Pedersen, C Flindt, N A Mortensen, M Brandbyge, T G Pedersen and A-P Jauho Splitting of critical energies in the n=0 Landau level of graphene Ana L C Pereira Double-gated graphene-based devices S Russo, M F Craciun, M Yamamoto, S Tarucha and A F Morpurgo Pinning and switching of magnetic moments in bilayer graphene Eduardo V Castro, M P Lopez-Sancho and M A H Vozmediano Electronic transport properties of graphene nanoribbons Katsunori Wakabayashi, Yositake Takane, Masayuki Yamamoto and Manfred Sigrist Many-body effects on out-of-plane phonons in graphene J Gonzalez and E Perfetto Graphene zigzag ribbons, square lattice models and quantum spin chains Mahdi Zarea and Nancy Sandler On the universal ac optical background in graphene V P Gusynin, S G Sharapov and J P Carbotte Heat conduction in graphene: experimental study and theoretical interpretation S Ghosh, D L Nika, E P Pokatilov and A A

  5. Stress wave focusing transducers

    Energy Technology Data Exchange (ETDEWEB)

    Visuri, S.R., LLNL

    1998-05-15

    Conversion of laser radiation to mechanical energy is the fundamental process behind many medical laser procedures, particularly those involving tissue destruction and removal. Stress waves can be generated with laser radiation in several ways: creation of a plasma and subsequent launch of a shock wave, thermoelastic expansion of the target tissue, vapor bubble collapse, and ablation recoil. Thermoelastic generation of stress waves generally requires short laser pulse durations and high energy density. Thermoelastic stress waves can be formed when the laser pulse duration is shorter than the acoustic transit time of the material: {tau}{sub c} = d/c{sub s} where d = absorption depth or spot diameter, whichever is smaller, and c{sub s} = sound speed in the material. The stress wave due to thermoelastic expansion travels at the sound speed (approximately 1500 m/s in tissue) and leaves the site of irradiation well before subsequent thermal events can be initiated. These stress waves, often evolving into shock waves, can be used to disrupt tissue. Shock waves are used in ophthalmology to perform intraocular microsurgery and photodisruptive procedures as well as in lithotripsy to fragment stones. We have explored a variety of transducers that can efficiently convert optical to mechanical energy. One such class of transducers allows a shock wave to be focused within a material such that the stress magnitude can be greatly increased compared to conventional geometries. Some transducer tips could be made to operate regardless of the absorption properties of the ambient media. The size and nature of the devices enable easy delivery, potentially minimally-invasive procedures, and precise tissue- targeting while limiting thermal loading. The transducer tips may have applications in lithotripsy, ophthalmology, drug delivery, and cardiology.

  6. Focusators for laser-branding

    Science.gov (United States)

    Doskolovich, L. L.; Kazanskiy, N. L.; Kharitonov, S. I.; Uspleniev, G. V.

    A new method is investigated for synthesis of computer-generated optical elements: focusators that are able to focus the radial-symmetrical laser beam into complex focal contours, in particular into alphanumeric symbols. The method is based on decomposition of the focal contour into segments of straight lines and semi-circles, following corresponding spacing out of the focusator on elementary segments (concentric rings or sectors) and solution of the inverse task of focusing from focusator segments into corresponding elements of the focal contour. The results of numerical computing of the field from synthesized focusators into the letters are presented. The theoretical efficiency of the focusators discussed is no less than 85%. The amplitude masks and the results of operational studies of synthesized focusators are presented.

  7. Prosodic Focus Marking in Bai.

    NARCIS (Netherlands)

    Liu, Zenghui; Chen, A.; Van de Velde, Hans

    2014-01-01

    This study investigates prosodic marking of focus in Bai, a Sino-Tibetan language spoken in the Southwest of China, by adopting a semi-spontaneous experimental approach. Our data show that Bai speakers increase the duration of the focused constituent and reduce the duration of the post-focus

  8. Focus Groups Help To Focus the Marketing Strategy.

    Science.gov (United States)

    Ashar, Hanna; Lane, Maureen

    1996-01-01

    A university-based degree completion program for adults conducted focus group research to refine market positioning and promotion. Focus groups averaged five current students and recent graduates who reflected, demographically, the current student population. Results gave insight into reasons for selecting the university, aspects of the program…

  9. Regulatory focus in groupt contexts

    NARCIS (Netherlands)

    Faddegon, Krispijn Johannes

    2009-01-01

    The thesis examines the influence of group processes on the regulatory focus of individual group members. It is demonstrated that the group situation can affect group members' regulatory focus both in a top-down fashion (via the identitiy of the group) and in a bottom-up fashion (emerging from the

  10. CTE's Focus on Continuous Improvement

    Science.gov (United States)

    Foster, John; Kelley, Patricia; Pritz, Sandy; Hodes, Carol

    2011-01-01

    Just one of the ways career and technical education (CTE) is revamping its image is through increased attention to data-driven instructional techniques as a means of improving and focusing instruction on what matters most. Accountability and data have increasingly become a core focus of research, news, and commentary about education in recent…

  11. On the Semantics of Focus

    Science.gov (United States)

    Kess, Joseph F.

    1975-01-01

    This article discusses the semantics of the notion of focus, insofar as it relates to Filipino languages. The evolution of this notion is reviewed, and an alternative explanation of it is given, stressing the fact that grammar and semantics should be kept separate in a discussion of focus. (CLK)

  12. Electric motors in the focus; Elektroantrieb im Focus

    Energy Technology Data Exchange (ETDEWEB)

    Wilms, Jan

    2013-05-15

    In August 2013, the first electric series production model of Ford comes to the market: the Focus Electric. A 23-kWh lithium-ion battery supplies the 107 kilowatts (145 hp) electric motor of the Focus Electric with energy. This battery enables a range of 162 kilometers and a limited top speed of 136 kilometers per hour. However, with 40,000 Euro this electric-powered vehicles is too expensive.

  13. Plutonium focus area: Technology summary

    International Nuclear Information System (INIS)

    1996-03-01

    To ensure research and development programs focus on the most pressing environmental restoration and waste management problems at the U.S. Department of Energy (DOE), the Assistant Secretary for the Office of Environmental Management (EM) established a working group in August 1993 to implement a new approach to research and technology development. As part of this approach, EM developed a management structure and principles that led to creation of specific focus areas. These organizations were designed to focus scientific and technical talent throughout DOE and the national scientific community on major environmental restoration and waste management problems facing DOE. The focus area approach provides the framework for inter-site cooperation and leveraging of resources on common problems. After the original establishment of five major focus areas within the Office of Technology Development (EM-50), the Nuclear Materials Stabilization Task Group (NMSTG, EM-66) followed EM-50's structure and chartered the Plutonium Focus Area (PFA). NMSTG's charter to the PFA, described in detail later in this book, plays a major role in meeting the EM-66 commitments to the Defense Nuclear Facilities Safety Board (DNFSB). The PFA is a new program for FY96 and as such, the primary focus of revision 0 of this Technology Summary is an introduction to the Focus Area; its history, development, and management structure, including summaries of selected technologies being developed. Revision 1 to the Plutonium Focus Area Technology Summary is slated to include details on all technologies being developed, and is currently planned for release in August 1996. The following report outlines the scope and mission of the Office of Environmental Management, EM-60, and EM-66 organizations as related to the PFA organizational structure

  14. Compact electron beam focusing column

    Science.gov (United States)

    Persaud, Arun; Leung, Ka-Ngo; Reijonen, Jani

    2001-12-01

    A novel design for an electron beam focusing column has been developed at LBNL. The design is based on a low-energy spread multicusp plasma source which is used as a cathode for electron beam production. The focusing column is 10 mm in length. The electron beam is focused by means of electrostatic fields. The column is designed for a maximum voltage of 50 kV. Simulations of the electron trajectories have been performed by using the 2D simulation code IGUN and EGUN. The electron temperature has also been incorporated into the simulations. The electron beam simulations, column design and fabrication will be discussed in this presentation.

  15. Focusing liquid microjets with nozzles

    International Nuclear Information System (INIS)

    Acero, A J; Ferrera, C; Montanero, J M; Gañán-Calvo, A M

    2012-01-01

    The stability of flow focusing taking place in a converging–diverging nozzle, as well as the size of the resulting microjets, is examined experimentally in this paper. The results obtained in most aspects of the problem are similar to those of the classical plate-orifice configuration. There is, however, a notable difference between flow focusing in nozzles and in the plate-orifice configuration. In the former case, the liquid meniscus oscillates laterally (global whipping) for a significant area of the control parameter plane, a phenomenon never observed when focusing with the plate-orifice configuration. Global whipping may constitute an important drawback of flow focusing with nozzles because it reduces the robustness of the technique. (paper)

  16. Wayside Teaching: Focusing on Relationships

    Science.gov (United States)

    Powell, Sara Davis

    2011-01-01

    Wayside teaching focuses on building and maintaining positive relationships with students. Teachers can implement certain wayside teaching practices to end the year in a positive way and begin preparing for the next school year.

  17. A study of plasma focus

    International Nuclear Information System (INIS)

    Hirano, Katsumi; Majima, Kazuo

    1976-01-01

    The behavior of the plasma acceleration between electrodes, the phenomena due to the pinch effect at the top of the electrodes and the neutron emission mechanism were experimentally studied. The plasma focus device was a Mather type coaxial discharge device, and the instruments used for the present purpose were a Rogoski coil, an image converter camera, a scintillation detector and a silver foil activation counter. The results of the present experiment were as follows. Plasma focus was not definitely made under the same condition. When the focus was seen, a dip was observed in the discharge wave form, and the emissions of X-ray and neutrons were detected. The angular anisotropy of neutron emission was observed, and corresponds to a beam target model. The phenomena showing the occurrence of focus were seen, when the current sheet was produced at a delayed time after discharge, and arrived at the muzzle with large velocity. The relation between the number of emitted neutrons and the velocity of the current sheet was obtained, whereas no systematic relation exists between the number of emitted neutrons and the velocity of pinch. When the focus was not observed, no dip was seen in current wave form, and the emissions of X-ray and neutrons were not detected. The reason of no focus was considered. (Kato, T.)

  18. Stability of expanded plasma focus

    International Nuclear Information System (INIS)

    Soliman, H.M.

    1994-01-01

    In this study, the stabilization of the expanded plasma focus formed by 4.5 kJ plasma focus device of Mather type by magnetic field is presented. The experimental results of the induced axial magnetic field and electric probe measurements of the expanded plasma focus show that, the plasma consists of three plasmoids, electron temperature measurements off the plasmoids at a point close to the muzzle are 26 eV, 30 eV and 27 eV respectively and the electron densities are 6.6 x 10 14 , 6.1 x 10 14 / cm 3 respectively. The presence of external axial magnetic field (B 2 = 1.6 kg) at the mid distance between the breech and the muzzle has a less effect on the stability of expanded focus and it causes a restriction for the plasma motion. the electron temperature of the three plasmoids are found to increase in that case by 23%, 18.5% respectively. When this axial magnetic field is applied at the muzzle end, it leads to a more stable expanded plasma focus which consists mainly of one plasmoid with electron temperature of 39 eV and density of 3.4 x 10 14 / cm 3 . 5 figs

  19. Verum focus and polar questions

    Directory of Open Access Journals (Sweden)

    Ion Giurgea

    2012-11-01

    Full Text Available We argue that some word order phenomena in Romanian and Sardinian are the result of a checking operation in the left periphery involving verum focus (i.e. focus on the polarity component of the sentence. In particular, this operation accounts for some word order patterns found in polar questions. In Romanian, polarity fronting is realized as head-movement of (V+T to a higher peripheral head which bears a Focus-probe. This licenses VS orders for predications in which VS is not allowed as a neutral order (i-level predicates, iteratives, generics. In Sardinian, an entire phrase headed by the lexical predicate (verbal non-finite form or non-verbal predicate is fronted before the auxiliary. We argue that this order is obtained by two movement operations, head-raising of Aux to Foc and movement of the predicate phrase to SpecFoc. We also present the semantics of polarity focus, distinguishing several types of focus (informational, emphatic, contrastive.

  20. Magnetically focused liquid drop radiator

    Science.gov (United States)

    Botts, Thomas E.; Powell, James R.; Lenard, Roger

    1986-01-01

    A magnetically focused liquid drop radiator for application in rejecting rgy from a spacecraft, characterized by a magnetizable liquid or slurry disposed in operative relationship within the liquid droplet generator and its fluid delivery system, in combination with magnetic means disposed in operative relationship around a liquid droplet collector of the LDR. The magnetic means are effective to focus streams of droplets directed from the generator toward the collector, thereby to assure that essentially all of the droplets are directed into the collector, even though some of the streams may be misdirected as they leave the generator. The magnetic focusing means is also effective to suppress splashing of liquid when the droplets impinge on the collector.

  1. Finding beam focus errors automatically

    International Nuclear Information System (INIS)

    Lee, M.J.; Clearwater, S.H.; Kleban, S.D.

    1987-01-01

    An automated method for finding beam focus errors using an optimization program called COMFORT-PLUS. The steps involved in finding the correction factors using COMFORT-PLUS has been used to find the beam focus errors for two damping rings at the SLAC Linear Collider. The program is to be used as an off-line program to analyze actual measured data for any SLC system. A limitation on the application of this procedure is found to be that it depends on the magnitude of the machine errors. Another is that the program is not totally automated since the user must decide a priori where to look for errors

  2. Depletion field focusing in semiconductors

    NARCIS (Netherlands)

    Prins, M.W.J.; Gelder, Van A.P.

    1996-01-01

    We calculate the three-dimensional depletion field profile in a semiconductor, for a planar semiconductor material with a spatially varying potential upon the surface, and for a tip-shaped semiconductor with a constant surface potential. The nonuniform electric field gives rise to focusing or

  3. Instabilities in the plasma focus

    International Nuclear Information System (INIS)

    Kaeppeler, H.J.

    1975-03-01

    The plasma focus was studied by many research teams in view of a possible approach to controlled thermonuclear fusion. Though it is questionable whether the plasma focus will ever lead to a fusion reactor, it nevertheless constitutes a strong source of neutron, X- and gamma radiation for simulating fusion reactor conditions. Furthermore, the plasma focus yields very high temperatures (10 7 K) and densities (> 10 19 cm -3 ) and thus provides interesting conditions for the study of high density plasmas. This review paper starts with a description of the compression stage of the focussing plasma, using a snow-plough model. It is shown that sophisticated MHD calculations substantiate the snowplough theory, but are not suited to describe the phenomena in the final compressed stage. For this purpose, a particle-in-cell calculation is employed, yielding a beam-beam collision model for the neutron production. Experimental evidence indicates that neutron production is associated with the appearence of m = O instabilities and is the direct result of collisions between anomalously accelerated ions. One of the mechanisms of ion acceleration are strong local electric fields. Another possible mechanism can bee seen in beam-plasma instabilities caused by runaway electrons. The analytical derivation of the dispersion relation for plasma focus conditions including runaway effect is discussed (orig.) [de

  4. Focus group report, Part I

    International Nuclear Information System (INIS)

    1997-07-01

    The Waste Policy Institute, through a cooperative agreement with the U.S. Department of Energy's (DOE) Office of Science and Technology (OST), conducted two focus groups with people who live or work near DOE sites. The purpose of the focus groups was to gain a better understanding of the general community's information needs about the development of innovative technologies that are used in the cleanup of the sites. The authors wanted to better understand of what role these people want to play in the development of new technologies, how OST communication products can help facilitate that role, and the usefulness of current OST communication products. WPI held the focus groups in communities near the Idaho National Engineering and Environmental Laboratory (INEEL) and the Savannah River Site (SRS) because they are among the DOE sites that cannot be cleaned up before 2006. To include many facets of the communities, WPI randomly selected participants from membership lists of organized groups in each community including: elected officials, school boards, unions, chambers of commerce, economic development organizations, environmental organizations, health and human service organizations, and area clergy. While in the communities, WPI also interviewed stakeholders such as tribal representatives and a Citizens Advisory Board (CAB) member. Qualitative data gathered during the focus group sessions give some indication of general stakeholder opinions. However, the authors caution readers not to make broad assumptions about the general stakeholder audience based on the opinions of a limited number of general community stakeholders

  5. Technology for Education. IDRA Focus.

    Science.gov (United States)

    IDRA Newsletter, 1998

    1998-01-01

    This theme issue includes five articles that focus on technology for education to benefit all students, including limited-English-proficient, minority, economically disadvantaged, and at-risk students. "Coca-Cola Valued Youth Program Students Meet Peers Via Video Conference" (Linda Cantu, Leticia Lopez-De La Garza) describes how at-risk…

  6. Environmental Protection: a shifting focus

    NARCIS (Netherlands)

    Dr. ir. Jan Venselaar

    2004-01-01

    The last two decades have seen a fundamental change in the way chemistry handles environmental issues. A shift in focus has occurred from 'end-of-pipe' to prevention and process integration. Presently an even more fundamental change is brought about by the need for sustainable development. It is

  7. Focus groups in organizational research

    Directory of Open Access Journals (Sweden)

    L. Kamfer

    1989-05-01

    Full Text Available Focus groups are commonly used in marketing research. In this article an application of the focus group technique within an organizational context is described. Nine focus groups were conducted during the planning stage of a survey intended to establish employee perceptions of advancement policies and practices in a major South African manufacturing company. Fourteen themes emerged from a content analysis of the discussions. Two of these reflected aspects requiring commitment decisions from management toward the survey. The others indicated areas of concern which should be included in the survey. In this way, the focus groups contributed useful information for the subsequent sample survey. Opsomming Fokusgroepe word algemeen in bemarkingsnavorsing aangewend. In hierdie studie word 'n toepassingvan die fokusgroeptegniek in die konteks van 'n opname binne 'n organisasie beskryf. Nege fokusgroepbesprekings is gevoer tydens die beplanningstadium van 'n opname wat binne 'n Suid-Afrikaanse vervaardigingsonderneming gedoen is. Die doel van die opname was om die persepsies van werknemers teenoor die bestaande personeel- en bestuursontwikkelingsbeleid en -praktyke van die maatskappy te bepaal. Veertien temas is deur middel van 'n inhoudontleding gei'dentifiseer. Twee hiervan het aspekte aangedui waaroor bestuur beginselbesluite t.o.v. die opname sou moes neem. Die ander het probleemareas aangedui wat by die ondersoek selfingesluit behoort te word. Sodoende het die fokusgroepe inligting verskafwat vir die latere vraelysopname belangrik was.

  8. Verum focus and polar questions

    Directory of Open Access Journals (Sweden)

    Ion Giurgea

    2012-01-01

    Full Text Available We argue that some word order phenomena in Romanian and Sardinian are the result of a checkingoperation in the left periphery involving verum focus (i.e. focus on the polarity component of the sentence.In particular, this operation accounts for some word order patterns found in polar questions. In Romanian,polarity fronting is realized as head-movement of (V+T to a higher peripheral head which bears a Focusprobe.This licenses VS orders for predications in which VS is not allowed as a neutral order (i-levelpredicates, iteratives, generics. In Sardinian, an entire phrase headed by the lexical predicate (verbal nonfiniteform or non-verbal predicate is fronted before the auxiliary. We argue that this order is obtained bytwo movement operations, head-raising of Aux to Foc and movement of the predicate phrase to SpecFoc. Wealso present the semantics of polarity focus, distinguishing several types of focus (informational, emphatic,contrastive.

  9. Work and Family. Special Focus.

    Science.gov (United States)

    Goetz, Kathy, Ed.

    1992-01-01

    This newsletter issue focuses on issues concerning families with both parents employed outside the home and describes several employer programs designed to help employees balance their work and family life. The newsletter includes the following articles: (1) "Work and Family: 1992"; (2) "Levi Strauss and Co.--A Work/Family Program…

  10. FOREWORD: Focus on Advanced Ceramics Focus on Advanced Ceramics

    Science.gov (United States)

    Ohashi, Naoki

    2011-06-01

    Much research has been devoted recently to developing technologies for renewable energy and improving the efficiency of the processes and devices used in industry and everyday life. Efficient solutions have been found using novel materials such as platinum and palladium-based catalysts for car exhaust systems, samarium-cobalt and neodymium-iron-boron permanent magnets for electrical motors, and so on. However, their realization has resulted in an increasing demand for rare elements and in their deficit, the development of new materials based on more abundant elements and new functionalities of traditional materials. Moreover, increasing environmental and health concerns demand substitution of toxic or hazardous substances with nature-friendly alternatives. In this context, this focus issue on advanced ceramics aims to review current trends in ceramics science and technology. It is related to the International Conference on Science and Technology of Advanced Ceramics (STAC) held annually to discuss the emerging issues in the field of ceramics. An important direction of ceramic science is the collaboration between experimental and theoretical sciences. Recent developments in density functional theory and computer technology have enabled the prediction of physical and chemical properties of ceramics, thereby assisting the design of new materials. Therefore, this focus issue includes articles devoted to theory and advanced characterization techniques. As mentioned above, the potential shortage of rare elements is becoming critical to the industry and has resulted in a Japanese government initiative called the 'Ubiquitous Element Strategy'. This focus issue also includes articles related to this strategy and to the associated topics of energy conversion, such as phosphors for high-efficiency lighting and photocatalysts for solar-energy harvesting. We hope that this focus issue will provide a timely overview of current trends and problems in ceramics science and

  11. Plasma focusing in coaxial gun

    International Nuclear Information System (INIS)

    Soliman, H.M.; Masoud, M.M.; El-Khalafawy, T.

    1986-01-01

    A capacitor bank has been discharged between two coaxial electrodes of 6.6 cm outer diameter, 3.2 cm inner diameter and length of 31.5 cm. filled with hydrogen gas at pressure of 310 μHg. Results show that, the axial and radial plasma current reach a maximum value at a position adjacent to the gun muzzle, at which the plasma focus occurs. The measurement of the electron temperature and density and azimuthal electric field along the axis of the expansion chamber, gives a maximum value at z∼18 cm from the gun muzzle, while the axial plasma current and velocity has a minimum value at that position. These results indicate that a second point of a plasma focus has been formed at z∼18 cm from the gun muzzle, along the axis of the expansion chamber

  12. Focusing Telescopes in Nuclear Astrophysics

    CERN Document Server

    Ballmoos, Peter von

    2007-01-01

    This volume is the first of its kind on focusing gamma-ray telescopes. Forty-eight refereed papers provide a comprehensive overview of the scientific potential and technical challenges of this nascent tool for nuclear astrophysics. The book features articles dealing with pivotal technologies such as grazing incident mirrors, multilayer coatings, Laue- and Fresnel-lenses - and even an optic using the curvature of space-time. The volume also presents an overview of detectors matching the ambitious objectives of gamma ray optics, and facilities for operating such systems on the ground and in space. The extraordinary scientific potential of focusing gamma-ray telescopes for the study of the most powerful sources and the most violent events in the Universe is emphasized in a series of introductory articles. Practicing professionals, and students interested in experimental high-energy astrophysics, will find this book a useful reference

  13. Reflectors to Focus Wave Energy

    DEFF Research Database (Denmark)

    Kramer, Morten; Frigaard, Peter

    2005-01-01

    Wave Energy Converters (WEC’s) extract wave energy from a limited area, often a single point or line even though the wave energy is generally spread out along the wave crest. By the use of wave reflectors (reflecting walls) the wave energy is effectively focused and increased by approximately 30......-50%. Clearly longer wave reflectors will focus more wave energy than shorter wave reflectors. Thus the draw back is the increased wave forces for the longer wave reflectors. In the paper a procedure for calculating the energy efficiency and the wave forces on the reflectors are described, this by use of a 3D...... boundary element method. The calculations are verified by laboratory experiments and a very good agreement is found. The paper gives estimates of possible power benefit for different wave reflector geometries and optimal geometrical design parameters are specified. On this basis inventors of WEC’s can...

  14. Ion beam generation and focusing

    International Nuclear Information System (INIS)

    Miller, P.A.; Mendel, C.W.; Swain, D.W.; Goldstein, S.A.

    1975-01-01

    Calculations have shown that efficiently generated and focused ion beams could have significant advantages over electron beams in achieving ignition of inertially-confined thermonuclear fuel. Efficient ion beam generation implies use of a good ion source and suppression of net electron current. Net electron flow can be reduced by allowing electrons to reflex through a highly transparent anode or by use of transverse magnetic fields (either beam self-fields or externally applied fields). Geometric focusing can be achieved if the beam is generated by appropriately shaped electrodes. Experimental results are presented which demonstrate ion beam generation in both reflexing and pinched-flow diodes. Spherically shaped electrodes are used to concentrate a proton beam, and target response to proton deposition is studied

  15. Plasma-focused cyclic accelerators

    International Nuclear Information System (INIS)

    Mondelli, A.A.; Chernin, D.P.

    1985-01-01

    The use of ambient plasma to neutralize the transverse forces of an intense particle beam has been known for many years. Most recently, the so-called ion-focused regime (IFR) for beam propagation has been used as a means of focusing intense electron beams in linear accelerators and suggested for injecting an electron beam across magnetic field lines into a high-current cyclic accelerator. One technique for generating the required background plasma for IFR propagation is to use a laser to ionize ambient gas in the accelerator chamber. This paper discusses an alternative means of plasma production for IFR, viz. by using RF breakdown. For this approach the accelerator chamber acts as a waveguide. This technique is not limited to toroidal accelerators. It may be applied to any accelerator or recirculator geometry as well as for beam steering and for injection or extraction of beams in closed accelerator configurations

  16. Optimum Design of Plasma Focus

    International Nuclear Information System (INIS)

    Ramos, Ruben; Gonzalez, Jose; Clausse, Alejandro

    2000-01-01

    The optimum design of Plasma Focus devices is presented based in a lumped parameter model of the MHD equations.Maps in the design parameters space are obtained, which determine the length and deuterium pressure required to produce a given neutron yield.Sensitivity analyses of the main effective numbers (sweeping efficiencies) was performed, and lately the optimum values were determined in order to set a basis for the conceptual design

  17. Focus On Photoshop Elements Focus on the Fundamentals

    CERN Document Server

    Asch, David

    2011-01-01

    Are you bewildered by the advanced editing options available in Photoshop Elements? Do you want to get the most out of your image without going bleary-eyed in front of a computer screen? This handy guide will explain the ins and outs of using Photoshop Elements, without having to spend hours staring at the screen. Using a fabulous combination of easy-to-follow advice and step-by-step instructions, Focus On Photoshop Elements gives great advice on setting up, storing and sharing your image library and teaches you the basics of RAW image processing and color correction, plus shows you how to edi

  18. Focusing of Shear Shock Waves

    Science.gov (United States)

    Giammarinaro, Bruno; Espíndola, David; Coulouvrat, François; Pinton, Gianmarco

    2018-01-01

    Focusing is a ubiquitous way to transform waves. Recently, a new type of shock wave has been observed experimentally with high-frame-rate ultrasound: shear shock waves in soft solids. These strongly nonlinear waves are characterized by a high Mach number, because the shear wave velocity is much slower, by 3 orders of magnitude, than the longitudinal wave velocity. Furthermore, these waves have a unique cubic nonlinearity which generates only odd harmonics. Unlike longitudinal waves for which only compressional shocks are possible, shear waves exhibit cubic nonlinearities which can generate positive and negative shocks. Here we present the experimental observation of shear shock wave focusing, generated by the vertical motion of a solid cylinder section embedded in a soft gelatin-graphite phantom to induce linearly vertically polarized motion. Raw ultrasound data from high-frame-rate (7692 images per second) acquisitions in combination with algorithms that are tuned to detect small displacements (approximately 1 μ m ) are used to generate quantitative movies of gel motion. The features of shear shock wave focusing are analyzed by comparing experimental observations with numerical simulations of a retarded-time elastodynamic equation with cubic nonlinearities and empirical attenuation laws for soft solids.

  19. High efficiency focus neutron generator

    Science.gov (United States)

    Sadeghi, H.; Amrollahi, R.; Zare, M.; Fazelpour, S.

    2017-12-01

    In the present paper, the new idea to increase the neutron yield of plasma focus devices is investigated and the results are presented. Based on many studies, more than 90% of neutrons in plasma focus devices were produced by beam target interactions and only 10% of them were due to thermonuclear reactions. While propounding the new idea, the number of collisions between deuteron ions and deuterium gas atoms were increased remarkably well. The COMSOL Multiphysics 5.2 was used to study the given idea in the known 28 plasma focus devices. In this circumstance, the neutron yield of this system was also obtained and reported. Finally, it was found that in the ENEA device with 1 Hz working frequency, 1.1 × 109 and 1.1 × 1011 neutrons per second were produced by D-D and D-T reactions, respectively. In addition, in the NX2 device with 16 Hz working frequency, 1.34 × 1010 and 1.34 × 1012 neutrons per second were produced by D-D and D-T reactions, respectively. The results show that with regards to the sizes and energy of these devices, they can be used as the efficient neutron generators.

  20. Focus group report - part II

    International Nuclear Information System (INIS)

    1997-12-01

    The Waste Policy Institute, through a cooperative agreement with the U.S. Department of Energy (DOE) Office of Science and Technology (OST) conducted a focus group with members of the Hanford Advisory Board (HAB), interviews with tribal government representatives, and a survey of Oak Ridge Local Oversight Committee (LOC) and Site Specific Advisory Board (SSAB) members. The purpose was to understand what members of the interested and involved public want to know about technology development and ways to get that information to them. These data collection activities were used as a follow-up to two previously held focus groups with the general public near Idaho National Engineering and Environmental Laboratory (INEEL) and the Savannah River Site (SRS). Most participants from the first two focus groups said they did not have time and/or were not interested in participating in technology decision-making. They said they would prefer to defer to members of their communities who are interested and want to be involved in technology decision-making

  1. The quest for customer focus.

    Science.gov (United States)

    Gulati, Ranjay; Oldroyd, James B

    2005-04-01

    Companies have poured enormous amounts of money into customer relationship management, but in many cases the investment hasn't really paid off. That's because getting closer to customers isn't about building an information technology system. It's a learning journey-one that unfolds over four stages, requiring people and business units to coordinate in progressively more sophisticated ways. The journey begins with the creation of a companywide repository containing each interaction a customer has with the company, organized not by product, purchase, or location, but by customer. Communal coordination is what's called for at this stage, as each group contributes its information to the data pool separately from the others and then taps into it as needed. In the second stage, one-way serial coordination from centralized IT through analytical units and out to the operating units allows companies to go beyond just assembling data to drawing inferences. In stage three, companies shift their focus from past relationships to future behavior. Through symbiotic coordination, information flows back and forth between central analytic units and various organizational units like marketing, sales, and operations, as together they seek answers to questions like "How can we prevent customers from switching to a competitor?" and "Who would be most likely to buy a new product in the future"? In stage four, firms begin to move past discrete, formal initiatives and, through integral coordination, bring an increasingly sophisticated understanding oftheir customers to bear in all day-to-day operations. Skipping stages denies organizations the sure foundation they need to build a lasting customer-focused mind-set. Those that recognize this will invest their customer relationship dollars much more wisely-and will see their customer-focusing efforts pay offon the bottom line.

  2. A focused bibliography on robotics

    Science.gov (United States)

    Mergler, H. W.

    1983-08-01

    The present bibliography focuses on eight robotics-related topics believed by the author to be of special interest to researchers in the field of industrial electronics: robots, sensors, kinematics, dynamics, control systems, actuators, vision, economics, and robot applications. This literature search was conducted through the 1970-present COMPENDEX data base, which provides world-wide coverage of nearly 3500 journals, conference proceedings and reports, and the 1969-1981 INSPEC data base, which is the largest for the English language in the fields of physics, electrotechnology, computers, and control.

  3. Focus on topological quantum computation

    International Nuclear Information System (INIS)

    Pachos, Jiannis K; Simon, Steven H

    2014-01-01

    Topological quantum computation started as a niche area of research aimed at employing particles with exotic statistics, called anyons, for performing quantum computation. Soon it evolved to include a wide variety of disciplines. Advances in the understanding of anyon properties inspired new quantum algorithms and helped in the characterization of topological phases of matter and their experimental realization. The conceptual appeal of topological systems as well as their promise for building fault-tolerant quantum technologies fuelled the fascination in this field. This ‘focus on’ collection brings together several of the latest developments in the field and facilitates the synergy between different approaches. (editorial)

  4. Focus on astronomical predictable events

    DEFF Research Database (Denmark)

    Jacobsen, Aase Roland

    2006-01-01

    At the Steno Museum Planetarium we have for many occasions used a countdown clock to get focus om astronomical events. A countdown clock can provide actuality to predictable events, for example The Venus Transit, Opportunity landing on Mars and The Solar Eclipse. The movement of the clock attracs...... the public and makes a point of interest in a small exhibit area. A countdown clock can be simple, but it is possible to expand the concept to an eye-catching part of a museum....

  5. Catastrophe in plasma focus evolution

    International Nuclear Information System (INIS)

    Ikuta, Kazunari.

    1984-07-01

    A theory of generating strong electric field in a dense plasma column in plasma focus is established by applying the formula for the electron thermal conductivity in destroyed magnetic surfaces like those in tokamaks. The origin of the electric field may be from abrupt rise of plasma resistivity when the irregularity of magnetic field is weak. However, the electric field can be from the inductive origin in case the irregularity attains a certain level. Both origin should be mixed up depending on the magnitude of the irregularity. (author)

  6. Final focus system for TLC

    International Nuclear Information System (INIS)

    Oide, K.

    1988-11-01

    A limit of the chromaticity correction for the final focus system of a TeV Linear Collider (TLC) is investigated. As the result, it becomes possible to increase the aperture of the final doublet with a small increase of the horizontal β function. The new optics design uses a final doublet of 0.5 mm half-aperture and 1.4 T pole-tip field. The length of the system is reduced from 400 m to 200 m by several optics changes. Tolerances for various machine errors with this optics are also studied. 5 refs., 7 figs., 2 tabs

  7. Focus on the Rashba effect

    Science.gov (United States)

    Bihlmayer, G.; Rader, O.; Winkler, R.

    2015-05-01

    The Rashba effect, discovered in 1959, continues to supply fertile ground for fundamental research and applications. It provided the basis for the proposal of the spin transistor by Datta and Das in 1990, which has largely inspired the broad and dynamic field of spintronics. More recent developments include new materials for the Rashba effect such as metal surfaces, interfaces and bulk materials. It has also given rise to new phenomena such as spin currents and the spin Hall effect, including its quantized version, which has led to the very active field of topological insulators. The Rashba effect plays a crucial role in yet more exotic fields of physics such as the search for Majorana fermions at semiconductor-superconductor interfaces and the interaction of ultracold atomic Bose and Fermi gases. Advances in our understanding of Rashba-type spin-orbit couplings, both qualitatively and quantitatively, can be obtained in many different ways. This focus issue brings together the wide range of research activities on Rashba physics to further promote the development of our physical pictures and concepts in this field. The present Editorial gives a brief account on the history of the Rashba effect including material that was previously not easily accessible before summarizing the key results of the present focus issue as a guidance to the reader.

  8. Plutonium focus area. Technology summary

    International Nuclear Information System (INIS)

    1997-09-01

    The Assistant Secretary for the Office of Environmental Management (EM) at the U.S. Department of Energy (DOE) chartered the Plutonium Focus Area (PFA) in October 1995. The PFA open-quotes...provides for peer and technical reviews of research and development in plutonium stabilization activities...close quotes In addition, the PFA identifies and develops relevant research and technology. The purpose of this document is to focus attention on the requirements used to develop research and technology for stabilization, storage, and preparation for disposition of nuclear materials. The PFA Technology Summary presents the approach the PFA uses to identify, recommend, and review research. It lists research requirements, research being conducted, and gaps where research is needed. It also summarizes research performed by the PFA in the traditional research summary format. This document encourages researchers and commercial enterprises to do business with PFA by submitting research proposals or open-quotes white papers.close quotes In addition, it suggests ways to increase the likelihood that PFA will recommend proposed research to the Nuclear Materials Stabilization Task Group (NMSTG) of DOE

  9. Plasma-focused cyclic accelerators

    International Nuclear Information System (INIS)

    Mondelli, A.A.; Chernin, D.P.

    1985-01-01

    The use of ambient plasma to neutralize the transverse forces of an intense particle beam has been known for many years. Most recently, the so-called ion-focused regime (IFR) for beam propagation has been used as a means of focusing intense electron beams in linear accelerators and suggested for injecting an electron beam across magnetic field lines into a high-current cyclic accelerator. One technique for generating the required background plasma for IFR propagation is to use a laser to ionize ambient gas in the accelerator chamber. For cyclic accelerators a technique is required for carrying the plasma channel and the beam around a bend. Multiple laser-generated channels with dipole magnetic fields to switch the beam from one channel to the next have been tested at Sandia. This paper discusses an alternative means of plasma production for IFR, viz. by using rf breakdown. For this approach the accelerator chamber acts as a waveguide. With a suitable driving frequency, a waveguide mode can be driven which has its peak field intensity on the axis with negligible fields at the chamber walls. The plasma production and hence the beam propagation is thereby isolated from the walls. This technique is not limited to toroidal accelerators. It may be applied to any accelerator or recirculator geometry as well as for beam steering and for injection or extraction of beams in closed accelerator configurations

  10. Focusing telescopes in nuclear astrophysics

    International Nuclear Information System (INIS)

    Von Ballmoos, P.; Knodlseder, R.; Sazonov, S.; Griffiths, R.; Bastie, P.; Halloin, H.; Pareschi, G.; Ramsey, B.; Jensen, C.; Buis, E.J.; Ulmer, M.; Giommi, P.; Colafrancesco, S.; Comastri, A.; Barret, D.; Leising, M.; Hernanz, M.; Smith, D.; Abrosimov, N.; Smither, B.; Ubertini, P.; Olive, J.F.; Lund, N.; Pisa, A.; Courtois, P.; Roa, D.; Harrison, F.; Pareschi, G.; Frontera, F.; Von Ballmoos, P.; Barriere, N.; Rando, N.; Borde, J.; Hinglais, E.; Cledassou, R.; Duchon, P.; Sghedoni, M.; Huet, B.; Takahashi, T.; Caroli, E.; Quadrinin, L.; Buis, E.J.; Skinner, G.; Krizmanic, J.; Pareschi, G.; Loffredo, G.; Wunderer, C.; Weidenspointner, G.; Wunderer, C.; Koechlin, L.; Bignami, G.; Von Ballmoos, P.; Tueller, J.; Andritschke, T.; Laurens, A.; Evrard, J.

    2005-01-01

    The objective of this workshop is to consider the next generation of instrumentation to be required within the domain of nuclear astrophysics. A small, but growing community has been pursuing various techniques for the focusing of hard X-rays and gamma-rays with the aim of achieving a factor of up to 100 improvement in sensitivity over present technologies. Balloon flight tests of both multilayer mirrors and a Laue lens have been performed and ideas abound. At present, implementation scenarios for space missions are being studied at Esa, CNES, and elsewhere. The workshop will provide a first opportunity for this new community to meet, exchange technological know-how, discuss scientific objectives and synergies, and consolidate implementation approaches within National and European Space Science programs. This document gathers the slides of all the presentations

  11. Focus on integrated quantum optics

    International Nuclear Information System (INIS)

    O'Brien, Jeremy; Patton, Brian; Sasaki, Masahide; Vučković, Jelena

    2013-01-01

    A key goal of research into quantum information processing is the development of technologies that are scaleable in complexity while allowing the mass manufacture of devices that promise transformative effects on information science. The demonstration that integrated photonics circuits could be made to perform operations that exploit the quantum nature of the photon has turned them into leading candidates for practical quantum information processing technologies. To fully achieve their promise, however, requires research from diverse fields. This focus issue provides a snapshot of some of the areas in which key advances have been made. We are grateful for the contributions from leading teams based around the globe and hope that the degree of progress being made in a challenging and exciting field is apparent from the papers published here. (editorial)

  12. Focusing telescopes in nuclear astrophysics

    Energy Technology Data Exchange (ETDEWEB)

    Von Ballmoos, P; Knodlseder, R; Sazonov, S; Griffiths, R; Bastie, P; Halloin, H; Pareschi, G; Ramsey, B; Jensen, C; Buis, E J; Ulmer, M; Giommi, P; Colafrancesco, S; Comastri, A; Barret, D; Leising, M; Hernanz, M; Smith, D; Abrosimov, N; Smither, B; Ubertini, P; Olive, J F; Lund, N; Pisa, A; Courtois, P; Roa, D; Harrison, F; Pareschi, G; Frontera, F; Von Ballmoos, P; Barriere, N; Rando, N; Borde, J; Hinglais, E; Cledassou, R; Duchon, P; Sghedoni, M; Huet, B; Takahashi, T; Caroli, E; Quadrinin, L; Buis, E J; Skinner, G; Krizmanic, J; Pareschi, G; Loffredo, G; Wunderer, C; Weidenspointner, G; Wunderer, C; Koechlin, L; Bignami, G; Von Ballmoos, P; Tueller, J; Andritschke, T; Laurens, A; Evrard, J

    2005-07-01

    The objective of this workshop is to consider the next generation of instrumentation to be required within the domain of nuclear astrophysics. A small, but growing community has been pursuing various techniques for the focusing of hard X-rays and gamma-rays with the aim of achieving a factor of up to 100 improvement in sensitivity over present technologies. Balloon flight tests of both multilayer mirrors and a Laue lens have been performed and ideas abound. At present, implementation scenarios for space missions are being studied at Esa, CNES, and elsewhere. The workshop will provide a first opportunity for this new community to meet, exchange technological know-how, discuss scientific objectives and synergies, and consolidate implementation approaches within National and European Space Science programs. This document gathers the slides of all the presentations.

  13. Tank Focus Area pretreatment activities

    International Nuclear Information System (INIS)

    McGinnis, C.P.; Welch, T.D.; Manke, K.L.

    1997-01-01

    Plans call for the high-level wastes to be retrieved from the tanks and immobilized in a stable waste form suitable for long-term isolation. Chemistry and chemical engineering operations are required to retrieve the wastes, to condition the wastes for subsequent steps, and to reduce the costs of the waste management enterprise. Pretreatment includes those processes between retrieval and immobilization, and includes preparation of suitable feed material for immobilization and separations to partition the waste into streams that yield lower life-cycle costs. Some of the technologies being developed by the Tank Focus Area (TFA) to process these wastes are described. These technologies fall roughly into three areas: (1) solid/liquid separation (SLS), (2) sludge pretreatment, and (3) supernate pretreatment

  14. Focus: Asian migration to Canada.

    Science.gov (United States)

    Kobayashi, A

    1988-01-01

    This collection of 5 short essays on Asian migration to Canada focuses on the relationships between individual migrants and their social contexts, both Asian and Canadian. Papers by Anderson and Kobayashi adopt research perspectives of outsider and insider, respectively. Vibert provides a historical overview against which the substantive issues introduced in the other 3 papers can be understood, and he illustrates the links between circumstances of migration and the larger issues by which the course of Canadian social progress has been steered. Mercer provides an introduction to issues that dominate the agenda of contemporary research, to show that Canadian communities of Asian heritage continue to grow in size, diversity, and complexity, as they become more established on the Canadian landscape. This collection is as much about the geography of racism as it is about migration.

  15. Focus on quantum Einstein gravity Focus on quantum Einstein gravity

    Science.gov (United States)

    Ambjorn, Jan; Reuter, Martin; Saueressig, Frank

    2012-09-01

    The gravitational asymptotic safety program summarizes the attempts to construct a consistent and predictive quantum theory of gravity within Wilson's generalized framework of renormalization. Its key ingredient is a non-Gaussian fixed point of the renormalization group flow which controls the behavior of the theory at trans-Planckian energies and renders gravity safe from unphysical divergences. Provided that the fixed point comes with a finite number of ultraviolet-attractive (relevant) directions, this construction gives rise to a consistent quantum field theory which is as predictive as an ordinary, perturbatively renormalizable one. This opens up the exciting possibility of establishing quantum Einstein gravity as a fundamental theory of gravity, without introducing supersymmetry or extra dimensions, and solely based on quantization techniques that are known to work well for the other fundamental forces of nature. While the idea of gravity being asymptotically safe was proposed by Steven Weinberg more than 30 years ago [1], the technical tools for investigating this scenario only emerged during the last decade. Here a key role is played by the exact functional renormalization group equation for gravity, which allows the construction of non-perturbative approximate solutions for the RG-flow of the gravitational couplings. Most remarkably, all solutions constructed to date exhibit a suitable non-Gaussian fixed point, lending strong support to the asymptotic safety conjecture. Moreover, the functional renormalization group also provides indications that the central idea of a non-Gaussian fixed point providing a safe ultraviolet completion also carries over to more realistic scenarios where gravity is coupled to a suitable matter sector like the standard model. These theoretical successes also triggered a wealth of studies focusing on the consequences of asymptotic safety in a wide range of phenomenological applications covering the physics of black holes, early

  16. Patient satisfaction: focusing on "excellent".

    Science.gov (United States)

    Otani, Koichiro; Waterman, Brian; Faulkner, Kelly M; Boslaugh, Sarah; Burroughs, Thomas E; Dunagan, W Claiborne

    2009-01-01

    In an emerging competitive market such as healthcare, managers should focus on achieving excellent ratings to distinguish their organization from others. When it comes to customer loyalty, "excellent" has a different meaning. Customers who are merely satisfied often do not come back. The purpose of this study was to find out what influences adult patients to rate their overall experience as "excellent." The study used patient satisfaction data collected from one major academic hospital and four community hospitals. After conducting a multiple logistic regression analysis, certain attributes were shown to be more likely than others to influence patients to rate their experiences as excellent. The study revealed that staff care is the most influential attribute, followed by nursing care. These two attributes are distinctively stronger drivers of overall satisfaction than are the other attributes studied (i.e., physician care, admission process, room, and food). Staff care and nursing care are under the control of healthcare managers. If improvements are needed, they can be accomplished through training programs such as total quality management or continuous quality improvement, through which staff employees and nurses learn to be sensitive to patients' needs. Satisfying patients' needs is the first step toward having loyal patients, so hospitals that strive to ensure their patients are completely satisfied are more likely to prosper.

  17. Magnetic tearing in plasma focus

    International Nuclear Information System (INIS)

    Sharkawy, W.

    1994-01-01

    A plasma focus device used is Mather type filled with hydrogen gas at pressure between 0.1 and 1 torr. When connected to a large capacitor ≤10 KV a discharge is started with peak current 100 KA. Under the influence of the radial electric field E r , due to the potential between electrodes, and B φ the plasma will drift in the axial direction with velocity cE r /B φ . An induced axial magnetic field B z has been detected which due to sheath velocity. A propagation of magnetosonic wave has been observed with velocity ≅10 3 m sec -1 . Such a wave might be excited when the magnetic pressure is much greater than the plasma kinetic pressure B 2 /8π>nKT. Assuming (MHD) to be stable, Tearing model was driven which generally has smaller growth rates than (MHD) modes. Using the designed theoretical model and the plasma parameters the electron energy dΦ/dt=Ba 2 /τ R was calculated to be 2.22 KeV, which is comparable with that detected from X-ray measurements. (author)

  18. Focus issue introduction: nonlinear photonics.

    Science.gov (United States)

    Akhmediev, Nail; Rottwitt, Karsten

    2012-11-19

    It is now 23 years since the first Topical Meeting "Nonlinear Guided Wave Phenomena" (Houston, TX, February 2-4, 1989) has been organised by George Stegeman and Allan Boardman with support of the Optical Society of America. These series of the OSA conferences known as NLGW, continued under the name "Nonlinear Photonics" starting from 2007. The latest one, in Colorado Springs in June 17-21, 2012 has been a great success despite the fierce fires advancing around the city at the time of the conference. This Focus issue is a collection of several papers presented at the conference with extended content submitted to Optics Express. Although this collection is small in comparison to the total number of papers presented at the conference, it gives a flavor of the topics considered at the meeting. It is also worthy to mention here that the next meeting "Nonlinear Photonics" is planned to be held in Barcelona - one of the main European centers on this subject.

  19. Findings: LANL outsourcing focus groups

    Energy Technology Data Exchange (ETDEWEB)

    Jannotta, M.J.; McCabe, V.B.

    1996-12-31

    In March 1996, a series of 24 3-hour dialog focus groups were held with randomly selected Laboratory employees and contractors to gain their perceptions regarding potentials and problems for privatization and consolidation. A secondary goal was to educate and inform the workforce about potentials and issues in privatization and consolidation. Two hundred and thirty-six participants engaged in a learning session and structured input exercises resulting in 2,768 usable comments. Comments were categorized using standard qualitative methods; resulting categories included positive and negative comments on four models (consolidation, spin offs, outsourcing, and corporate partnering) and implications for the workforce, the Laboratory, and the local economy. Categories were in the areas of increasing/decreasing jobs, expertise, opportunity/salary/benefits, quality/efficiency, and effect on the local area and economy. An additional concern was losing Laboratory culture and history. Data were gathered and categorized on employee opinion regarding elements of successful transition to the four models, and issues emerged in the areas of terms and conditions of employment; communication; involvement; sound business planning; ethics and fairness; community infrastructure. From the aggregated opinion of the participants, it is recommended that decision-makers: Plan using sound business principles and continually communicate plans to the workforce; Respect workforce investments in the Laboratory; Tell the workforce exactly what is going on at all times; Understand that economic growth in Northern New Mexico is not universally viewed as positive; and Establish dialog with stakeholders on growth issues.

  20. Workshop on crystals and focusing

    Science.gov (United States)

    Berreman, D. W.

    1980-12-01

    The purpose of the workshop on crystals and focusing was to exchange and pool the experience and information that the participants could contribute on the design and construction of monochromators for EXAFS with optimum speed, resolution and versatility. The panel was chaired by D.W. Berreman of BTL and included G. G. Cohen of NBS, S. Heald of Brookhaven National Labs and Lu Kun-quan of U. of Washington. Written contributions for the workshop were made by R. J. Emrich and J. R. Katzer of U. of Delaware, R. C. Gamble of Cal. Tech., J. Crane of Cal. Tech., and T. Matsushita of S. S. R. L. G. Bunker of U. of Washington was recording secretary, G. G. Cohen and S. Heald gave invited papers on the main program that were relevant to the workshop. Other contributors were R. Hänsel of U. of Kiel, W. Germany, G. Christoff of Ohio State and D. Hempstead of Rigaku/USA Inc., J. Holben of Marconi Avionics, Hertfordshire, England and J. Hastings of Brookhaven N. L.

  1. EDITORIAL: Focus on Carbon Nanotubes

    Science.gov (United States)

    2003-09-01

    The study of carbon nanotubes, since their discovery by Iijima in 1991, has become a full research field with significant contributions from all areas of research in solid-state and molecular physics and also from chemistry. This Focus Issue in New Journal of Physics reflects this active research, and presents articles detailing significant advances in the production of carbon nanotubes, the study of their mechanical and vibrational properties, electronic properties and optical transitions, and electrical and transport properties. Fundamental research, both theoretical and experimental, represents part of this progress. The potential applications of nanotubes will rely on the progress made in understanding their fundamental physics and chemistry, as presented here. We believe this Focus Issue will be an excellent guide for both beginners and experts in the research field of carbon nanotubes. It has been a great pleasure to edit the many excellent contributions from Europe, Japan, and the US, as well from a number of other countries, and to witness the remarkable effort put into the manuscripts by the contributors. We thank all the authors and referees involved in the process. In particular, we would like to express our gratitude to Alexander Bradshaw, who invited us put together this Focus Issue, and to Tim Smith and the New Journal of Physics staff for their extremely efficient handling of the manuscripts. Focus on Carbon Nanotubes Contents Transport theory of carbon nanotube Y junctions R Egger, B Trauzettel, S Chen and F Siano The tubular conical helix of graphitic boron nitride F F Xu, Y Bando and D Golberg Formation pathways for single-wall carbon nanotube multiterminal junctions Inna Ponomareva, Leonid A Chernozatonskii, Antonis N Andriotis and Madhu Menon Synthesis and manipulation of carbon nanotubes J W Seo, E Couteau, P Umek, K Hernadi, P Marcoux, B Lukic, Cs Mikó, M Milas, R Gaál and L Forró Transitional behaviour in the transformation from active end

  2. Focused conformational sampling in proteins

    Science.gov (United States)

    Bacci, Marco; Langini, Cassiano; Vymětal, Jiří; Caflisch, Amedeo; Vitalis, Andreas

    2017-11-01

    A detailed understanding of the conformational dynamics of biological molecules is difficult to obtain by experimental techniques due to resolution limitations in both time and space. Computer simulations avoid these in theory but are often too short to sample rare events reliably. Here we show that the progress index-guided sampling (PIGS) protocol can be used to enhance the sampling of rare events in selected parts of biomolecules without perturbing the remainder of the system. The method is very easy to use as it only requires as essential input a set of several features representing the parts of interest sufficiently. In this feature space, new states are discovered by spontaneous fluctuations alone and in unsupervised fashion. Because there are no energetic biases acting on phase space variables or projections thereof, the trajectories PIGS generates can be analyzed directly in the framework of transition networks. We demonstrate the possibility and usefulness of such focused explorations of biomolecules with two loops that are part of the binding sites of bromodomains, a family of epigenetic "reader" modules. This real-life application uncovers states that are structurally and kinetically far away from the initial crystallographic structures and are also metastable. Representative conformations are intended to be used in future high-throughput virtual screening campaigns.

  3. Focusing on Cause or Cure?

    Science.gov (United States)

    Milner, Lauren C.; Cho, Mildred K.

    2013-01-01

    Background Biomedical research is influenced by many factors, including the involvement of stakeholder groups invested in research outcomes. Stakeholder involvement in research efforts raise questions of justice as their specific interests and motivations play a role in directing research resources that ultimately produce knowledge shaping how different conditions (and affected individuals) are understood and treated by society. This issue is highly relevant to child psychiatry research where diagnostic criteria and treatment strategies are often controversial. Biological similarities and stakeholder differences between attention deficit hyperactivity disorder (ADHD) and autism spectrum disorder (ASD) provide an opportunity to explore this issue by comparing research foci and stakeholder involvement in these conditions. Methods A subset of ADHD and ASD research articles published between 1970-2010 were randomly selected from the PubMed database and coded for research focus, funding source(s), and author-reported conflicts of interest (COIs). Chi-square analyses were performed to identify differences between and within ADHD and ASD research across time. Results The proportion of ADHD research dedicated to basic, description, and treatment research was roughly similar and remained stable over time, while ASD research showed a significant increase in basic research over the past decade. Government was the primary research funder for both conditions, but for-profit funders were a notable presence in ADHD research, while joint-funding efforts between non-profit and government funders were a notable presence in ASD research. Lastly, COIs were noted more frequently in ADHD than in ASD research. Conclusions Our study shows significant differences in research foci and funding sources between the conditions, and identifies the specific involvement of for-profit and non-profit groups in ADHD and ASD, respectively. Our findings highlight the relationship between stakeholders

  4. Focus groups reveal consumer ambivalence.

    Science.gov (United States)

    1983-01-01

    According to qualitative research, Salvadoreans are ambivalent about the use of contraceptives. Since complete responsibility for management of the CSM project was accepted by the Association Demografica Salvadorena (ADS), the agency which operates the contraceptive social marketing project in El Salvador, in November 1980, the need for decisions in such areas as product price increases, introduction of new condom brands, promotion of the vaginal foaming tablet, and assessment of product sales performance had arisen. The ICSMP funded market research, completed during 1983, was intended to provide the data on which such decisions by ADS could be based. The qualitative research involved 8 focus groups, comprised of men and women, aged 18-45, contraceptive users and nonusers, from the middle and lower socioeconomic strata of the city of San Salvador and other suburban areas. In each group a moderator led discussion of family planning and probed respondents for specific attitudes, knowledge, and behavior regarding the use of contraceptives. To assess attitudes at a more emotional level, moderators asked respondents to "draw" their ideas on certain issues. A marked discrepancy was revealed between respondents' intellectual responses to the issues raised in group discussion, as opposed to their feelings expressed in the drawings. Intellectually, participants responded very positively to family planning practice, but when they were asked to draw their perceptions, ambivalent feelings emerged. Drawings of both the user and the nonuser convey primarily negative aspects for either choice. The user is tense and moody toward her children; the nonuser loses her attractiveness and "dies." Figures also show drawings of some of the attitudes of single and married male participants. 1 drawing shows an incomplete and a complete circle, symbolizing a sterilized man (incomplete) and a nonsterilized man (complete). Another picture depicts a chained man who has lost his freedom

  5. Keep the focus on emissions

    Science.gov (United States)

    Clack, C.; Benson, S. M.; Peterson, P.; Long, J. C. S.

    2016-12-01

    Most think that the major battle over climate is between those that want to solve the climate problem and the climate deniers. But there is another conflict, perhaps equally significant between people who all agree climate is a problem but who disagree radically about what they think the solution is. The imperative for stopping further climate change is to stop GHG emissions and the first energy sector of importance is electricity. Every major plan to eliminate emmissions from energy requires a carbon-free electricity system. The most popular idea about how to do this is to use all renewable energy, i.e. solar and wind power. But no one has ever built a large scale 100% renewable energy system and the few examples we have about regions that have tried are not encouraging. As the percentage of renewable energy goes up, ensuring a reliable supply often requires a fossil-based back-up system, so emissions can actually increase. Also, 100% renewable systems rely on massive deployment rates, far beyond any historical precident and often assume that adequate energy storage will "happen" through a combination of currently unavailable technologies. This approach is about adding renewable capacity, not about reducing emissions. Sweden provides a counter example that relies entirely on nuclear power and hydro and has an emission-free, reliable energy system. Likewise, biofuel is often cited as a climate-friendly substitute for petroleum-based fuels. Life-cycle analsyis indicates biofuels are often worse than petroleum-based fuels. We focus efficiency measures on buildings, but efficiency in transportation is even more important because we don't really have the fuel that is carbon neutral. Vehicle efficiency and reductions in vehicle miles traveled does better to address emissions. As mitigation is so important, climate advocates used to think discussion of adaptation was a distraction that should be avoided. But losing track of the need to eliminate emissions is the real

  6. EDITORIAL: Focus on Plasma Medicine

    Science.gov (United States)

    Morfill, G. E.; Kong, M. G.; Zimmermann, J. L.

    2009-11-01

    'Plasma Healthcare' is an emerging interdisciplinary research topic of rapidly growing importance, exploring considerable opportunities at the interface of plasma physics, chemistry and engineering with life sciences. Some of the scientific discoveries reported so far have already demonstrated clear benefits for healthcare in areas of medicine, food safety, environmental hygiene, and cosmetics. Examples include ongoing studies of prion inactivation, chronic wound treatment and plasma-mediated cancer therapy. Current research ranges from basic physical processes, plasma chemical design, to the interaction of plasmas with (i) eukaryotic (mammalian) cells; (ii) prokaryotic (bacteria) cells, viruses, spores and fungi; (iii) DNA, lipids, proteins and cell membranes; and (iv) living human, animal and plant tissues in the presence of biofluids. Of diverse interests in this new field is the need for hospital disinfection, in particular with respect to the alarming increase in bacterial resistance to antibiotics, the concomitant needs in private practices, nursing homes etc, the applications in personal hygiene—and the enticing possibility to 'design' plasmas as possible pharmaceutical products, employing ionic as well as molecular agents for medical treatment. The 'delivery' of the reactive plasma agents occurs at the gaseous level, which means that there is no need for a carrier medium and access to the treatment surface is optimal. This focus issue provides a close look at the current state of the art in Plasma Medicine with a number of forefront research articles as well as an introductory review. Focus on Plasma Medicine Contents Application of epifluorescence scanning for monitoring the efficacy of protein removal by RF gas-plasma decontamination Helen C Baxter, Patricia R Richardson, Gaynor A Campbell, Valeri I Kovalev, Robert Maier, James S Barton, Anita C Jones, Greg DeLarge, Mark Casey and Robert L Baxter Inactivation factors of spore-forming bacteria using low

  7. EDITORIAL: Focus on Attosecond Physics

    Science.gov (United States)

    Bandrauk, André D.; Krausz, Ferenc; Starace, Anthony F.

    2008-02-01

    future involve using overdense plasmas. Electronic processes on sub-atomic spatio-temporal scales are the basis of chemical physics, atomic, molecular, and optical physics, materials science, and even some life science processes. Research in these areas using the new attosecond tools will advance together with the ability to control electrons themselves. Indeed, we expect that developments will advance in a way that is similar to advances that have occurred on the femtosecond time scale, in which much previous experimental and theoretical work on the interaction of coherent light sources has led to the development of means for 'coherent control' of nuclear motion in molecules. This focus issue of New Journal of Physics is centered on experimental and theoretical advances in the development of new methodologies and tools for electron control on the attosecond time scale. Topics such as the efficient generation of harmonics; the generation of attosecond pulses, including those having only a few cycles and those produced from overdense plasmas; the description of various nonlinear, nonperturbative laser-matter interactions, including many-electron effects and few-cycle pulse effects; the analysis of ultrashort propagation effects in atomic and molecular media; and the development of inversion methods for electron tomography, as well as many other topics, are addressed in the current focus issue dedicated to the new field of 'Attosecond Physics'. Focus on Attosecond Physics Contents Observing the attosecond dynamics of nuclear wavepackets in molecules by using high harmonic generation in mixed gases Tsuneto Kanai, Eiji J Takahashi, Yasuo Nabekawa and Katsumi Midorikawa Core-polarization effects in molecular high harmonic generation G Jordan and A Scrinzi Interferometric autocorrelation of an attosecond pulse train calculated using feasible formulae Y Nabekawa and K Midorikawa Attosecond pulse generation from aligned molecules—dynamics and propagation in H2+ E Lorin, S

  8. Ion Motion in the Adiabatic Focuser

    International Nuclear Information System (INIS)

    Henestroza, E.; Sessler, A.M.; Yu, S.S.

    2006-01-01

    In this paper we numerically study the effect of ion motion in an adiabatic focuser, motivated by a recent suggestion that ion motion in an adiabatic focuser might be significant and even preclude operation of the focuser as previously envisioned. It is shown that despite ion motion the adiabatic focuser should work as well as originally envisioned

  9. EDITORIAL: Focus on Gravitational Lensing

    Science.gov (United States)

    Jain, Bhuvnesh

    2007-11-01

    Gravitational lensing emerged as an observational field following the 1979 discovery of a doubly imaged quasar lensed by a foreground galaxy. In the 1980s and '90s dozens of other multiply imaged systems were observed, as well as time delay measurements, weak and strong lensing by galaxies and galaxy clusters, and the discovery of microlensing in our galaxy. The rapid pace of advances has continued into the new century. Lensing is currently one of best techniques for finding and mapping dark matter over a wide range of scales, and also addresses broader cosmological questions such as understanding the nature of dark energy. This focus issue of New Journal of Physics presents a snapshot of current research in some of the exciting areas of lensing. It provides an occasion to look back at the advances of the last decade and ahead to the potential of the coming years. Just about a decade ago, microlensing was discovered through the magnification of stars in our galaxy by invisible objects with masses between that of Jupiter and a tenth the mass of the Sun. Thus a new component of the mass of our galaxy, dubbed MACHOs, was established (though a diffuse, cold dark matter-like component is still needed to make up most of the galaxy mass). More recently, microlensing led to another exciting discovery—of extra-solar planets with masses ranging from about five times that of Earth to that of Neptune. We can expect many more planets to be discovered through ongoing surveys. Microlensing is the best technique for finding Earth mass planets, though it is not as productive overall as other methods and does not allow for follow up observations. Beyond planet hunting, microlensing has enabled us to observe previously inaccessible systems, ranging from the surfaces of other stars to the accretion disks around the black holes powering distant quasars. Galaxies and galaxy clusters at cosmological distances can produce dramatic lensing effects: multiple images of background galaxies

  10. Night Vision Goggles Objectives Lens Focusing Methodology

    National Research Council Canada - National Science Library

    Pinkus, Alan; Task, H. L

    2000-01-01

    ...: interpupillary distance, tilt, eye relief, height, eyepiece and objective lens focus. Currently, aircrew use a Hoffman 20/20 test unit to pre-focus their NVG objective lenses at optical infinity before boarding their aircraft...

  11. Self-focusing in laser produced spark

    International Nuclear Information System (INIS)

    Bakos, J.S.; Foeldes, I.B.

    1983-05-01

    The self-focusing effect appearing in different phases of development of laser produced breakdown plasma in air is investigated. Self-focusing during the ionization process is demonstrated. Thermal self-focusing was observed in the later stage of the plasma development at moderate light intensities. Plasma development was investigated by forward and side scattering of the laser light in the plasma. A crossed beam experiment gave evidence of the thermal mechanism of self-focusing. (author)

  12. Near-field flat focusing mirrors

    Science.gov (United States)

    Cheng, Yu-Chieh; Staliunas, Kestutis

    2018-03-01

    This article reviews recent progress towards the design of near-field flat focusing mirrors, focusing/imaging light patterns in reflection. An important feature of such flat focusing mirrors is their transverse invariance, as they do not possess any optical axis. We start with a review of the physical background to the different focusing mechanisms of near- and far-field focusing. These near-field focusing devices like flat lenses and the reviewed near-field focusing mirrors can implement planar focusing devices without any optical axis. In contrast, various types of far-field planar focusing devices, such as high-contrast gratings and metasurfaces, unavoidably break the transverse invariance due to their radially symmetrical structures. The particular realizations of near-field flat focusing mirrors including Bragg-like dielectric mirrors and dielectric subwavelength gratings are the main subjects of the review. The first flat focusing mirror was demonstrated with a chirped mirror and was shown to manage an angular dispersion for beam focusing, similar to the management of chromatic dispersion for pulse compression. Furthermore, the reviewed optimized chirped mirror demonstrated a long near-field focal length, hardly achieved by a flat lens or a planar hyperlens. Two more different configurations of dielectric subwavelength gratings that focus a light beam at normal or oblique incidence are also reviewed. We also summarize and compare focusing performance, limitations, and future perspectives between the reviewed flat focusing mirrors and other planar focusing devices including a flat lens with a negative-index material, a planar hyperlens, a high-contrast grating, and a metasurface.

  13. Analysis and modeling of "focus" in context

    DEFF Research Database (Denmark)

    Hovy, Dirk; Anumanchipalli, Gopala; Parlikar, Alok

    2013-01-01

    This paper uses a crowd-sourced definition of a speech phenomenon we have called focus. Given sentences, text and speech, in isolation and in context, we asked annotators to identify what we term the focus word. We present their consistency in identifying the focused word, when presented with text...... or speech stimuli. We then build models to show how well we predict that focus word from lexical (and higher) level features. Also, using spectral and prosodic information, we show the differences in these focus words when spoken with and without context. Finally, we show how we can improve speech synthesis...

  14. Synthetic focusing in ultrasound modulated tomography

    KAUST Repository

    Kuchment, Peter; Kunyansky, Leonid

    2010-01-01

    Several hybrid tomographic methods utilizing ultrasound modulation have been introduced lately. Success of these methods hinges on the feasibility of focusing ultrasound waves at an arbitrary point of interest. Such focusing, however, is difficult to achieve in practice. We thus propose a way to avoid the use of focused waves through what we call synthetic focusing, i.e. by reconstructing the would-be response to the focused modulation from the measurements corresponding to realistic unfocused waves. Examples of reconstructions from simulated data are provided. This non-technical paper describes only the general concept, while technical details will appear elsewhere. © 2010 American Institute of Mathematical Sciences.

  15. Synthetic focusing in ultrasound modulated tomography

    KAUST Repository

    Kuchment, Peter

    2010-09-01

    Several hybrid tomographic methods utilizing ultrasound modulation have been introduced lately. Success of these methods hinges on the feasibility of focusing ultrasound waves at an arbitrary point of interest. Such focusing, however, is difficult to achieve in practice. We thus propose a way to avoid the use of focused waves through what we call synthetic focusing, i.e. by reconstructing the would-be response to the focused modulation from the measurements corresponding to realistic unfocused waves. Examples of reconstructions from simulated data are provided. This non-technical paper describes only the general concept, while technical details will appear elsewhere. © 2010 American Institute of Mathematical Sciences.

  16. [Pre-verbality in focusing and the need for self check. An attempt at "focusing check"].

    Science.gov (United States)

    Masui, T; Ikemi, A; Murayama, S

    1983-06-01

    Though the Focusing process is not entirely non-verbal, in Focusing, careful attention is paid by the Focuser and the Listener to the pre-verbal experiential process. In other words, Focusing involves attending to the felt sense that is not easily expressed in words immediately. Hence, during the process of learning to Focus, the Focusing teacher attempts to communicate the experiences of Focusing to the student which are not easily done by words. Due to such difficulties, the Focusing student may (and quite frequently does) mistake the experiential process in Focusing with other processes. Often, the felt sense can be confused with other phenomena such as "autogenic discharge". Also the Focuser may not stay with the felt sense and drift into "free association" or frequently, certain processes in "meditation" can be confused with Focusing. Therefore, there is a need for a "check" by which the Focusing student can confirm the Focusing experience for himself. For the Focusing student, such a "check" serves not only to confirm the Focusing process, but also an aid to learning Focusing. We will report here a "Focusing Check" which we developed by translating Eugene Gendlin's "Focusing Check" and making several modifications in it so that it will be more understandable to the Japanese. Along with the "Focusing Check" we developed, the authors discuss the need for such a check.

  17. Thermal self-focusing at oblique incidence

    International Nuclear Information System (INIS)

    Craxton, R.S.; McCrory, R.L.

    1984-03-01

    Thermal self-focusing at oblique incidence has been investigated in two-dimensional line-focus geometry using the Eulerian hydrodynamics simulation code SAGE. The laser beam interacts with a long-scale-length preformed plasma with an expontial density profiele. Questions to be addressed include: (1) What happens when a self-focusing channel reaches the turning point of the incident rays, and (2) Does the unabsorbed light return in the specular direction or back along the channel. A comparison is also made between thermal self-focusing at normal incidence in cylindrical and line-focus geometries: in cylindrical geometry the self-focusing mechanism is enhanced by the relative ease with which plasma may be expelled from a small cylindrical channel

  18. Needs of Non Energy-Focused Contractors

    Energy Technology Data Exchange (ETDEWEB)

    Liaukus, C.

    2012-12-01

    To better understand the informational needs of non energy-focused contractors, including what information they need to motivate them to become energy-focused, the BARA team studied the type of information provided by the national programs, trade associations, and manufacturers that were researched for the related technical report: Effective Communication of Energy Efficiency. While that report focused on the delivery method, format, and strategy of the information, this study examines the content being put forward.

  19. Needs of Non-Energy Focused Contractors

    Energy Technology Data Exchange (ETDEWEB)

    Liakus, C. [Building Media and the Building America Retrofit Alliance (BARA), Wilmington, DE (United States)

    2012-12-01

    To better understand the informational needs of non-energy focused contractors, including what information they need to motivate them to become energy-focused, the BARA team studied the type of information provided by the national programs, trade associations, and manufacturers that were researched for the related technical report: Effective Communication of Energy Efficiency. While that report focused on the delivery method, format, and strategy of the information, this study examines the content being put forward.

  20. Suppression of radiation excitation in focusing environment

    International Nuclear Information System (INIS)

    Huang, Z.; Ruth, R.D.

    1996-12-01

    Radiation damping and quantum excitation in an electron damping ring and a straight focusing channel are reviewed. They are found to be the two limiting cases in the study of a general bending and focusing combined system. In the intermediate regime where the radiation formation length is comparable to the betatron wavelength, quantum excitation can be exponentially suppressed by focusing field. This new regime may have interesting applications in the generation of ultra-low emittance beams

  1. Thermal self-focusing with multiple beams

    International Nuclear Information System (INIS)

    Craxton, R.S.; McCrory, R.L.

    1986-07-01

    Self-focusing in underdense plasmas in the presence of overlapping beams is of interest for multibeam laser-irradiation systems. The hydrodynamics/ray-tracing simulation code SAGE is used to model thermal self-focusing in two-dimensional line-focus geometry with beams incident obliquely at different angles. The conjecture that multiple overlapping beams may suppress self-focusing is investigated for parameters appropriate to reactor-sized targets; in particular, the dependence upon intensity, scale length and pulse width is examined. While the full problem is three-dimensional, insight may be gained from two-dimensional simulations

  2. Automatic focusing system of BSST in Antarctic

    Science.gov (United States)

    Tang, Peng-Yi; Liu, Jia-Jing; Zhang, Guang-yu; Wang, Jian

    2015-10-01

    Automatic focusing (AF) technology plays an important role in modern astronomical telescopes. Based on the focusing requirement of BSST (Bright Star Survey Telescope) in Antarctic, an AF system is set up. In this design, functions in OpenCV is used to find stars, the algorithm of area, HFD or FWHM are used to degree the focus metric by choosing. Curve fitting method is used to find focus position as the method of camera moving. All these design are suitable for unattended small telescope.

  3. Regulatory focus affects physician risk tolerance.

    Science.gov (United States)

    Veazie, Peter J; McIntosh, Scott; Chapman, Benjamin P; Dolan, James G

    2014-01-01

    Risk tolerance is a source of variation in physician decision-making. This variation, if independent of clinical concerns, can result in mistaken utilization of health services. To address such problems, it will be helpful to identify nonclinical factors of risk tolerance, particularly those amendable to intervention-regulatory focus theory suggests such a factor. This study tested whether regulatory focus affects risk tolerance among primary care physicians. Twenty-seven primary care physicians were assigned to promotion-focused or prevention-focused manipulations and compared on the Risk Taking Attitudes in Medical Decision Making scale using a randomization test. Results provide evidence that physicians assigned to the promotion-focus manipulation adopted an attitude of greater risk tolerance than the physicians assigned to the prevention-focused manipulation (p = 0.01). The Cohen's d statistic was conventionally large at 0.92. Results imply that situational regulatory focus in primary care physicians affects risk tolerance and may thereby be a nonclinical source of practice variation. Results also provide marginal evidence that chronic regulatory focus is associated with risk tolerance (p = 0.05), but the mechanism remains unclear. Research and intervention targeting physician risk tolerance may benefit by considering situational regulatory focus as an explanatory factor.

  4. FEMP Focus: 2011 Volume 20 Issue 1

    Energy Technology Data Exchange (ETDEWEB)

    None

    2011-04-05

    Department of Energy (DOE); Federal Energy Management Program; FEMP Focus Newsletter; December 2010; Alternative Financing, Guidance Documents, Recovery Act Technical Assistance, Training, Energy Awareness

  5. Using Focus Group Research in Public Relations.

    Science.gov (United States)

    Grunig, Larissa A.

    1990-01-01

    Analyzes a recent instance of focus group research applied to a public relations case (rather than a marketing case). Reviews the advantages and disadvantages of this qualitative method, and describes the case of a county department of mental health relying on focus group research to help plan a program aimed at reducing the stigma of mental…

  6. Identifying Information Focuses in Listening Comprehension

    Science.gov (United States)

    Zhang, Hong-yan

    2011-01-01

    The study explains the process of learners' listening comprehension within Halliday's information theory in functional grammar, including the skills of identifying focuses while listening in college English teaching. Identifying information focuses in listening is proved to improve the students' communicative listening ability by the means of a…

  7. Plasma lenses for focusing relativistic electron beams

    International Nuclear Information System (INIS)

    Govil, R.; Wheeler, S.; Leemans, W.

    1997-01-01

    The next generation of colliders require tightly focused beams with high luminosity. To focus charged particle beams for such applications, a plasma focusing scheme has been proposed. Plasma lenses can be overdense (plasma density, n p much greater than electron beam density, n b ) or underdense (n p less than 2 n b ). In overdense lenses the space-charge force of the electron beam is canceled by the plasma and the remaining magnetic force causes the electron beam to self-pinch. The focusing gradient is nonlinear, resulting in spherical aberrations. In underdense lenses, the self-forces of the electron beam cancel, allowing the plasma ions to focus the beam. Although for a given beam density, a uniform underdense lens produces smaller focusing gradients than an overdense lens, it produces better beam quality since the focusing is done by plasma ions. The underdense lens can be improved by tapering the density of the plasma for optimal focusing. The underdense lens performance can be enhanced further by producing adiabatic plasma lenses to avoid the Oide limit on spot size due to synchrotron radiation by the electron beam. The plasma lens experiment at the Beam Test Facility (BTF) is designed to study the properties of plasma lenses in both overdense and underdense regimes. In particular, important issues such as electron beam matching, time response of the lens, lens aberrations and shot-to-shot reproducibility are being investigated

  8. Attentional Focusing Instructions and Force Production

    Directory of Open Access Journals (Sweden)

    David C Marchant

    2011-01-01

    Full Text Available Research progress assessing the role of attentional focusing instructions on skill acquisition and performance has lead researchers to apply this approach to force production tasks. Initial converging evidence indicates that force production tasks are sensitive to verbal instruction; externally focused instructions (onto movement outcomes, or onto the object force is being exerted against are shown to be more beneficial than internally focused instructions (focusing attention onto the movements being executed. These benefits are observed for maximal and accurate force production, as well as the maintenance of force production in prolonged tasks. A range of mechanisms are identified supporting the proposal that an external focus promotes movement efficiency in line with energy and effort conservation. Future research is required to assess how this developing body of work interacts with the broader understanding of psychological and physiological factors implicated in the effective production, maintenance and limitation of maximal or sub-maximal forces.

  9. Final focus systems for linear colliders

    International Nuclear Information System (INIS)

    Erickson, R.A.

    1987-11-01

    The final focus system of a linear collider must perform two primary functions, it must focus the two opposing beams so that their transverse dimensions at the interaction point are small enough to yield acceptable luminosity, and it must steer the beams together to maintain collisions. In addition, the final focus system must transport the outgoing beams to a location where they can be recycled or safely dumped. Elementary optical considerations for linear collider final focus systems are discussed, followed by chromatic aberrations. The design of the final focus system of the SLAC Linear Collider (SLC) is described. Tuning and diagnostics and steering to collision are discussed. Most of the examples illustrating the concepts covered are drawn from the SLC, but the principles and conclusions are said to be generally applicable to other linear collider designs as well. 26 refs., 17 figs

  10. Tanks Focus Area annual report FY2000

    International Nuclear Information System (INIS)

    2000-01-01

    The U.S. Department of Energy (DOE) continues to face a major radioactive waste tank remediation effort with tanks containing hazardous and radioactive waste resulting from the production of nuclear materials. With some 90 million gallons of waste in the form of solid, sludge, liquid, and gas stored in 287 tanks across the DOE complex, containing approximately 650 million curies, radioactive waste storage tank remediation is the nation's highest cleanup priority. Differing waste types and unique technical issues require specialized science and technology to achieve tank cleanup in an environmentally acceptable manner. Some of the waste has been stored for over 50 years in tanks that have exceeded their design lives. The challenge is to characterize and maintain these contents in a safe condition and continue to remediate and close each tank to minimize the risks of waste migration and exposure to workers, the public, and the environment. In 1994, the DOE's Office of Environmental Management (EM) created a group of integrated, multiorganizational teams focusing on specific areas of the EM cleanup mission. These teams have evolved into five focus areas managed within EM's Office of Science and Technology (OST): Tanks Focus Area (TFA); Deactivation and Decommissioning Focus Area; Nuclear Materials Focus Area; Subsurface Contaminants Focus Area; and Transuranic and Mixed Waste Focus Area

  11. Tanks Focus Area annual report FY2000

    Energy Technology Data Exchange (ETDEWEB)

    None

    2000-12-01

    The U.S. Department of Energy (DOE) continues to face a major radioactive waste tank remediation effort with tanks containing hazardous and radioactive waste resulting from the production of nuclear materials. With some 90 million gallons of waste in the form of solid, sludge, liquid, and gas stored in 287 tanks across the DOE complex, containing approximately 650 million curies, radioactive waste storage tank remediation is the nation's highest cleanup priority. Differing waste types and unique technical issues require specialized science and technology to achieve tank cleanup in an environmentally acceptable manner. Some of the waste has been stored for over 50 years in tanks that have exceeded their design lives. The challenge is to characterize and maintain these contents in a safe condition and continue to remediate and close each tank to minimize the risks of waste migration and exposure to workers, the public, and the environment. In 1994, the DOE's Office of Environmental Management (EM) created a group of integrated, multiorganizational teams focusing on specific areas of the EM cleanup mission. These teams have evolved into five focus areas managed within EM's Office of Science and Technology (OST): Tanks Focus Area (TFA); Deactivation and Decommissioning Focus Area; Nuclear Materials Focus Area; Subsurface Contaminants Focus Area; and Transuranic and Mixed Waste Focus Area.

  12. Deep-Focusing Time-Distance Helioseismology

    Science.gov (United States)

    Duvall, T. L., Jr.; Jensen, J. M.; Kosovichev, A. G.; Birch, A. C.; Fisher, Richard R. (Technical Monitor)

    2001-01-01

    Much progress has been made by measuring the travel times of solar acoustic waves from a central surface location to points at equal arc distance away. Depth information is obtained from the range of arc distances examined, with the larger distances revealing the deeper layers. This method we will call surface-focusing, as the common point, or focus, is at the surface. To obtain a clearer picture of the subsurface region, it would, no doubt, be better to focus on points below the surface. Our first attempt to do this used the ray theory to pick surface location pairs that would focus on a particular subsurface point. This is not the ideal procedure, as Born approximation kernels suggest that this focus should have zero sensitivity to sound speed inhomogeneities. However, the sensitivity is concentrated below the surface in a much better way than the old surface-focusing method, and so we expect the deep-focusing method to be more sensitive. A large sunspot group was studied by both methods. Inversions based on both methods will be compared.

  13. Technology of a small plasma focus

    International Nuclear Information System (INIS)

    Lee, S.

    1990-01-01

    This paper reviews plasma focus technology, including the underlying dynamic and energy balance theory, scaling of the neutron yield, cost effectiveness of the design, as well as the main subsystems, e.g., capacitor bank, spark-gap switch and triggering electronics, the plasma focus tube, some simple diagnostics, and a high-voltage charger. It discusses the range of densities and temperatures available with a small plasma focus, and the type of experiments and applications that can be carried out with it. 61 refs, 21 figs

  14. Designing focusing solenoids for superconducting RF accelerators

    Energy Technology Data Exchange (ETDEWEB)

    Davis, G.; Kashikhin, V.V.; Page, T.; Terechkine, I.; Tompkins, J.; Wokas, T.; /Fermilab

    2006-08-01

    The design of a focusing solenoid for use in a superconducting RF linac requires resolving a range of problems with conflicting requirements. Providing the required focusing strength contradicts the goal of minimizing the stray field on the surfaces of adjacent superconducting RF cavities. The requirement of a compact solenoid, able to fit into a gap between cavities, contradicts the need of mechanical support necessary to restrain electromagnetic forces that can result in coil motion and subsequent quenching. In this report we will attempt to address these and other issues arising during the development of focusing solenoids. Some relevant test data will also be presented.

  15. Applications of focused ion beams in microelectronics

    International Nuclear Information System (INIS)

    Broughton, C.; Beale, M.I.J.; Deshmukh, V.G.I.

    1986-04-01

    We present the conclusions of the RSRE programme on the application of focused ion beams in microelectronics and review the literature published in this field. We discuss the design and performance of focused beam implanters and the viability of their application to semiconductor device fabrication. Applications in the areas of lithography, direct implantation and micromachining are discussed in detail. Comparisons are made between the use of focused ion beams and existing techniques for these fabrication processes with a strong emphasis placed on the relative throughputs. We present results on a novel spot size measurement technique and the effect of beam heating on resist. We also present the results of studies into implantation passivation of resist to oxygen plasma attack as basis for a dry development lithography scheme. A novel lithography system employing flood electron exposure from a photocathode which is patterned by a focused ion beam which can also be used to repair mask defects is considered. (author)

  16. Focus Cities : Reducing the Vulnerability, Poverty and ...

    International Development Research Centre (IDRC) Digital Library (Canada)

    Focus Cities : Reducing the Vulnerability, Poverty and Environmental Load in ... 000 lives in closely constructed houses built right up to the edge of the Rimac River. ... and the Lima Metropolitan Urban Plan will be updated in light of the results.

  17. Focusing on ADHD - Attention Deficit Hyperactivity Disorder

    Science.gov (United States)

    ... September 2014 Print this issue Focusing on ADHD Attention Deficit Hyperactivity Disorder En español Send us your comments ... might be signs of a developmental disorder called attention deficit hyperactivity disorder, or ADHD. ADHD is a common ...

  18. Spatial filters for focusing ultrasound images

    DEFF Research Database (Denmark)

    Jensen, Jørgen Arendt; Gori, Paola

    2001-01-01

    , but the approach always yields point spread functions better or equal to a traditional dynamically focused image. Finally, the process was applied to in-vivo clinical images of the liver and right kidney from a 28 years old male. The data was obtained with a single element transducer focused at 100 mm....... A new method for making spatial matched filter focusing of RF ultrasound data is proposed based on the spatial impulse response description of the imaging. The response from a scatterer at any given point in space relative to the transducer can be calculated, and this gives the spatial matched filter...... for synthetic aperture imaging for single element transducers. It is evaluated using the Field II program. Data from a single 3 MHz transducer focused at a distance of 80 mm is processed. Far from the transducer focal region, the processing greatly improves the image resolution: the lateral slice...

  19. Structural Analysis of Extended Plasma Focus Chamber

    International Nuclear Information System (INIS)

    Mohd Azhar Ahmad; Abdul Halim Baijan; Siti Aiasah Hashim

    2016-01-01

    Accelerator Development Centre (ADC) of Nuclear Malaysia intends to upgrade the plasma focus device. It involves the extension part placed on top of the existing plasma focus vacuum chamber. This extended vacuum chamber purposely to give an extra space in conducting experiments on the existing plasma focus chamber. The aim of upgrading the plasma focus device is to solve the limitation in research and analysis of sample due to its done in an open system that cause analysis of samples is limited and less optimal. This extended chamber was design in considering the ease of fabrication as well as durability of its structural. Thus, this paper discusses the structural analysis in term of pressure loading effect in extended chamber. (author)

  20. FOCUS AND CONSTITUENT QUESTION FORMATION IN DAGBANI

    African Journals Online (AJOL)

    Issah

    Key words: SpecFoc, focus marker, clause initial, constituent interrogatives, information ... 1Throughout this work, I use the phrase interrogative words in a general way to refer to the ...... Wh-Questions and extraction asymmetries in Malagasy.

  1. Symmetric lens with extended depth of focus

    OpenAIRE

    Cho, Sung Nae

    2008-01-01

    The lens surface profile is derived based on the instantaneous focal length versus the lens radius data. The lens design based on instantaneous focal length versus the lens radius data has many useful applications in software assisted image focusing technology.

  2. Social Work Intervention Focused on Transitions

    Science.gov (United States)

    2016-12-19

    Study Focus: 30-day Rehospitalizations Among At-risk Older Adults Randomized to a Social Work-driven Care Transitions Intervention; Heart Disease; Diabetes; Hypertension; Cancer; Depression; Asthma; Chronic Heart Failure; Chronic Obstructive Pulmonary Disease; Stroke

  3. Nonverbal communication in the focus-group

    Directory of Open Access Journals (Sweden)

    Alina Simona TECĂU

    2015-12-01

    Full Text Available In the process of analysing the information obtained through focus group qualitative marketing research, a very important source of data is represented by non-verbal communication. Although the literature reveals an abundance of published material that describes how data obtained through focus group should be analysed, one of the least addressed issue is the interpretation of signals from participants: gestures, posture, dynamic and rhythm of speech or even the silence. This Article addresses precisely aspects of non-verbal communication in the focus group's and although not intended to examine in detail the results of a focus group, it shows how some of signals transmitted by participants of such research have been analysed and interpreted.

  4. Niger institute focuses on financial accountability | IDRC ...

    International Development Research Centre (IDRC) Digital Library (Canada)

    2016-04-28

    Apr 28, 2016 ... Niger institute focuses on financial accountability ... on renewing outdated financial management systems that impeded effective management and reporting on its activities. ... Canada-Africa grants spur novel ideas, networks.

  5. Plasma focus as a pulsed power source

    International Nuclear Information System (INIS)

    Sahlin, H.; McFarland, G.; Barlett, R.; Gullickson, R.

    1975-01-01

    The plasma focus is a remarkable natural phenomena that achieves significant space-time compression of both particle and field energy. Depending on the mode of operation, about 20 percent of the bank energy can be concentrated into the kinetic energy of a thin, dense, cylindrically convergent gas shell, or into a small-diameter, high-ν/γ relativistic electron burst and oppositely directed ion burst. The kinetic energy of the fast ions and electrons can exceed the applied voltage by a factor of greater than 100. The different modes of energy concentration by the plasma focus are presented and discussed both in terms of their role in the direct yield of the focus and for the case of a plasma focus supplemented by various fusionable targets

  6. Focused labeled proof systems for modal logic

    OpenAIRE

    Miller , Dale; Volpe , Marco

    2015-01-01

    International audience; Focused proofs are sequent calculus proofs that group inference rules into alternating positive and negative phases. These phases can then be used to define macro-level inference rules from Gentzen's original and tiny introduction and structural rules. We show here that the inference rules of labeled proof systems for modal logics can similarly be described as pairs of such phases within the LKF focused proof system for first-order classical logic. We consider the syst...

  7. Superconducting quadrupoles for the SLC final focus

    International Nuclear Information System (INIS)

    Erickson, R.; Fieguth, T.; Murray, J.J.

    1987-01-01

    The final focus system of the SLC will be upgraded by replacing the final quadrupoles with higher gradient superconducting magnets positioned closer to the interaction point. The parameters of the new system have been chosen to be compatible with the experimental detectors with a minimum of changes to other final focus components. These parameter choices are discussed along with the expected improvement in SLC performance

  8. Superconducting quadrupoles for the SLC final focus

    International Nuclear Information System (INIS)

    Erickson, R.; Fieguth, T.; Murray, J.J.

    1987-01-01

    The final focus system of the SLC will be upgraded by replacing the final quadrupoles with higher gradient supperconducting magnets positioned closer to the interaction point. The parameters of the new system have been chosen to be compatible with the experimental detectors with a minimum of changes to other final focus components. These parameter choices are discussed along with the expected improvement in SLC performance

  9. The final focus test beam project

    International Nuclear Information System (INIS)

    Burke, D.

    1991-05-01

    An overview is given of the Final Focus Test Beam (FFTB) that is being constructed as a prototype final focus system for a future electron-positron linear collider. This beam line will use as input the 50 GeV electron beam from the SLC linac, and is designed to reduce the transverse dimensions of the beam spot at the focal point to 1 μm. 5 refs., 2 figs., 1 tab

  10. Draft of textbook focused on indirect taxes

    OpenAIRE

    Nováková, Hana

    2012-01-01

    The diploma thesis is about draft of textbook which is focused on indirect taxes for business school. The thesis is divided into theoretical and practical part. The theoretical part is focused on teaching tax issues at business school. Readers are introduced with basic studying documents, for example framework educational program and school educational program. In the following part I have conducted didactic analysis of curriculum and textbook of economics for business schools. The draft of t...

  11. Microflow Cytometers with Integrated Hydrodynamic Focusing

    Directory of Open Access Journals (Sweden)

    Martin Schmidt

    2013-04-01

    Full Text Available This study demonstrates the suitability of microfluidic structures for high throughput blood cell analysis. The microfluidic chips exploit fully integrated hydrodynamic focusing based on two different concepts: Two-stage cascade focusing and spin focusing (vortex principle. The sample—A suspension of micro particles or blood cells—is injected into a sheath fluid streaming at a substantially higher flow rate, which assures positioning of the particles in the center of the flow channel. Particle velocities of a few m/s are achieved as required for high throughput blood cell analysis. The stability of hydrodynamic particle positioning was evaluated by measuring the pulse heights distributions of fluorescence signals from calibration beads. Quantitative assessment based on coefficient of variation for the fluorescence intensity distributions resulted in a value of about 3% determined for the micro-device exploiting cascade hydrodynamic focusing. For the spin focusing approach similar values were achieved for sample flow rates being 1.5 times lower. Our results indicate that the performances of both variants of hydrodynamic focusing suit for blood cell differentiation and counting. The potential of the micro flow cytometer is demonstrated by detecting immunologically labeled CD3 positive and CD4 positive T-lymphocytes in blood.

  12. Veselago focusing of anisotropic massless Dirac fermions

    Science.gov (United States)

    Zhang, Shu-Hui; Yang, Wen; Peeters, F. M.

    2018-05-01

    Massless Dirac fermions (MDFs) emerge as quasiparticles in various novel materials such as graphene and topological insulators, and they exhibit several intriguing properties, of which Veselago focusing is an outstanding example with a lot of possible applications. However, up to now Veselago focusing merely occurred in p-n junction devices based on the isotropic MDF, which lacks the tunability needed for realistic applications. Here, motivated by the emergence of novel Dirac materials, we investigate the propagation behaviors of anisotropic MDFs in such a p-n junction structure. By projecting the Hamiltonian of the anisotropic MDF to that of the isotropic MDF and deriving an exact analytical expression for the propagator, precise Veselago focusing is demonstrated without the need for mirror symmetry of the electron source and its focusing image. We show a tunable focusing position that can be used in a device to probe masked atom-scale defects. This study provides an innovative concept to realize Veselago focusing relevant for potential applications, and it paves the way for the design of novel electron optics devices by exploiting the anisotropic MDF.

  13. Some optical diagnostics for the plasma focus

    International Nuclear Information System (INIS)

    Korzhavin, V.M.

    1980-01-01

    Some aspects of studying plasma focus dynamics are reported. Particular efforts were made to develop an infrared (IR) diagnostics. The plasma focus is formed in a discharge chamber, when shock waves and plasma sheath cumulate on the axis as a result of the break-down of filling gas by the application of high voltage. The current J was measured with a Rogovsky coil, and the voltage U was measured with a capacitor divider. The current derivative was measured with magnetic probes, and X-ray and neutron emission intensities were measured with a plastic scintillator. The total neutron yield were measured by the activation method. The time-integrated soft X-ray pictures of plasma focus were taken with a pin-hole camera. The formation and disruption of plasma focus were studied by multi-picture speed photography. Laser interferometry was used to study the time-space distribution of plasma density. For the study of turbulence phenomena in plasma focus, a new type IR detector was employed. The results of measurements suggest that there exists some superthermal radiation during the second compression of plasma focus, but it is not so strong. (Kato, T.)

  14. Focus is key: Panic-focused interpretations are associated with symptomatic improvement in panic-focused psychodynamic psychotherapy.

    Science.gov (United States)

    Keefe, John R; Solomonov, Nili; Derubeis, Robert J; Phillips, Alexander C; Busch, Fredric N; Barber, Jacques P; Chambless, Dianne L; Milrod, Barbara L

    2018-04-18

    This study examines whether, in panic-focused psychodynamic psychotherapy (PFPP), interpretations of conflicts that underlie anxiety (panic-focused or PF-interpretations) are specifically associated with subsequent panic disorder (PD) symptom improvement, over and above the provision of non-symptom-focused interpretations. Technique use in Sessions 2 and 10 of a 24-session PFPP protocol was assessed for the 65 patients with complete outcome data randomized to PFPP in a two-site trial of psychotherapies for PD. Sessions were rated in 15-min segments for therapists' use of PF-interpretations, non-PF-interpretations, and PF-clarifications. Robust regressions were conducted to examine the relationship between these interventions and symptom change subsequent to the sampled session. Interpersonal problems were examined as a moderator of the relationship of PF-interpretations to symptom change. At Session 10, but not at Session 2, patients who received a higher degree of PF-interpretations experienced greater subsequent improvement in panic symptoms. Non-PF-interpretations were not predictive. Patients with more interpersonal distress benefitted particularly from the use of PF-interpretations at Session 10. By the middle phase of PFPP, panic-focused interpretations may drive subsequent improvements in panic symptoms, especially among patients with higher interpersonal distress. Interpretations of conflict absent a panic focus may not be especially helpful.

  15. EPA Region 7 Aquatic Focus Areas (ECO_RES.R7_AQUATIC_FOCUS_AREAS)

    Data.gov (United States)

    U.S. Environmental Protection Agency — This shapefile consists of 347 individual Aquatic Ecological System (AES) polygons that are the Aquatic Conservation Focus Areas for EPA Region 7. The focus areas...

  16. Phase analysis and focusing of synchrotron radiation

    CERN Document Server

    Chubar, O; Snigirev, A

    1999-01-01

    High accuracy calculations of synchrotron radiation (SR) emitted by a relativistic electron show that the phase of the frequency domain electric field of SR differs from the phase of radiation of a virtual point source. These differences may result in the reduction of focusing efficiency of diffraction-limited SR, if the focusing is performed by conventional optical components optimised for point sources. We show that by applying a phase correction locally, one may transform the phase of SR electric field at a desired polarisation to that of a point source. Such corrections are computed for undulator radiation (planar and helical) and bending magnet radiation (central part and edges). The focusing of the corrected SR wavefront can result in the increase of peak intensity in the focused spot up to several times compared to the focusing without correction. For non-diffraction-limited radiation, the effect of the phase corrections is reduced. Due to this reason, the use of the proposed phase corrections in exist...

  17. The Realization of Focus in Asturian Spanish

    Directory of Open Access Journals (Sweden)

    Covadonga Sánchez-Alvarado

    2018-01-01

    Full Text Available Spanish was classified as a language that only exploits syntactic mechanisms to mark focus. Recent experimental studies, nonetheless, have shown that speakers of different dialects are also able to use prosody to different degrees. This study aims to provide further understanding on the role played by prosody in the realization of focus in Spanish by looking at Asturian Spanish, a dialect in contact with another Romance language, Asturian. The data from a contextualized sentence completion task revealed that a phonological distinction between specific pitch categories (L+focus being elicited (i.e., informational/non-corrective vs. contrastive/corrective. Nonetheless, it also showed that speakers exploit different prosodic features (i.e., pitch range, alignment, and duration to mark focus constituents, although their use differs as a result of that constituents’ function. These findings provide further support for the consideration of languages and specific dialects in a continuum based on the degree to which they use prosody to mark focus and to explore more in detail the phonetic implementation of focal accents.

  18. Axial sheath dynamics in a plasma focus

    International Nuclear Information System (INIS)

    Soliman, H.M.; El-Khalafawy, T.A.; Masoud, M.M.

    1990-01-01

    This paper presents the result of investigation with a 10 kJ Mather type plasma focus. It is operated in hydrogen gas at ambient pressure of 0.15--1 torr and charging voltage of 8--11 kV. Radial distribution of the current sheath density with axial distance has been estimated. Plasma rotation in the expansion chamber in the absence of external magnetic field has been detected. A plasma flare from the plasma focus region propagating in the radial direction has been observed. Streak photography shows two plasma streams flowing simultaneously out of the muzzle. The mean energy of the electron beam ejected from the pinch region of the focused plasma, was measured by retarding field analyzer to be 0.32 keV. The electron temperature of the plasma focus at peak compression was determined by measuring the X-ray intensity as a function of absorber thickness at a distance of 62 cm from the focus. The electron temperature has been found to 3 keV

  19. [Aerodynamic focusing of particles and heavy molecules

    International Nuclear Information System (INIS)

    de la Mora, J.F.

    1990-01-01

    By accelerating a gas containing suspended particles or large molecules through a converging nozzle, the suspended species may be focused and therefore used to write fine lines on a surface. Our objective was to study the limits on how narrow this focal region could be as a function of particle size. We find that, for monodisperse particles with masses m p some 3.6 x 10 5 times larger than the molecular mass m of the carrier gas (diameters above some 100 angstrom), there is no fundamental obstacle to directly write submicron features. However, this conclusion has been verified experimentally only with particles larger than 0.1 μm. Experimental, theoretical and numerical studies on the defocusing role of Brownian motion for very small particles or heavy molecules have shown that high resolution (purely aerodynamic) focusing is impossible with volatile molecules whose masses are typically smaller than 1000 Dalton. For these, the minimal focal diameter after optimization appears to be 5√(m/m p ) times the nozzle diameter d n . But combinations of focused lasers and aerodynamic focusing appear as promising for direct writing with molecular precursors. Theoretical and numerical schemes capable of predicting the evolution of the focusing beam, including Brownian motion effects, have been developed, although further numerical work would be desirable. 11 refs

  20. Task-focused modeling in automated agriculture

    Science.gov (United States)

    Vriesenga, Mark R.; Peleg, K.; Sklansky, Jack

    1993-01-01

    Machine vision systems analyze image data to carry out automation tasks. Our interest is in machine vision systems that rely on models to achieve their designed task. When the model is interrogated from an a priori menu of questions, the model need not be complete. Instead, the machine vision system can use a partial model that contains a large amount of information in regions of interest and less information elsewhere. We propose an adaptive modeling scheme for machine vision, called task-focused modeling, which constructs a model having just sufficient detail to carry out the specified task. The model is detailed in regions of interest to the task and is less detailed elsewhere. This focusing effect saves time and reduces the computational effort expended by the machine vision system. We illustrate task-focused modeling by an example involving real-time micropropagation of plants in automated agriculture.

  1. Focusing properties of cylindrical vector vortex beams

    Science.gov (United States)

    Xiaoqiang, Zhang; Ruishan, Chen; Anting, Wang

    2018-05-01

    In this paper, following Richards and Wolf vectorial diffraction theory, the focusing properties of cylindrical vector vortex beams (CVVB) are investigated, and a diffractive optical element (DOE) is designed to spatially modulate the amplitude of the CVVB. Simulated results show that the CVVB focused by an objective also carry orbital angular momentum (OAM), and the optical fields near the focal region can be modulated by changing the topological charge of the CVVB. We numerically simulate the focus properties of radially and azimuthally polarized beams with topological charge equal to 0, 1, 2 and 10 respectively. As a result, a dark channel with a length about 20 λ can be obtained. These new properties have the potential applications such as particle acceleration, optical trapping and material processing.

  2. Final focus systems for linear colliders

    International Nuclear Information System (INIS)

    Helm, R.; Irwin, J.

    1992-08-01

    Final focus systems for linear colliders present many exacting challenges in beam optics, component design, and beam quality. Efforts to resolve these problems as they relate to a new generation of linear colliders are under way at several laboratories around the world. We will outline criteria for final focus systems and discuss the current state of understanding and resolution of the outstanding problems. We will discuss tolerances on alignment, field quality and stability for optical elements, and the implications for beam parameters such as emittance, energy spread, bunch length, and stability in position and energy. Beam-based correction procedures, which in principle can alleviate many of the tolerances, will be described. Preliminary results from the Final Focus Test Beam (FFTB) under construction at SLAC will be given. Finally, we mention conclusions from operating experience at the Stanford Linear Collider (SLC)

  3. Final focus systems for linear colliders

    International Nuclear Information System (INIS)

    Helm, R.; Irwing, J.

    1992-01-01

    Final focus systems for linear colliders present many exacting challenges in beam optics, component design, and beam quality. Efforts to resolve these problems as they relate to a new generation of linear colliders are under way at several laboratories around the world. We outline criteria for final focus systems and discuss the current state of understanding and resolution of the outstanding problems. We discuss tolerances on alignment, field quality and stability for optical elements, and the implications for beam parameters such as emittance, energy spread , bunch length, and stability in position and energy. Beam-based correction procedures, which in principle can alleviate many of the tolerances, are described. Preliminary results from the Final Focus Test Beam (FFTB) under construction at SLAC are given. Finally, we mention conclusions from operating experience at the Stanford Linear Collider (SLC). (Author) 16 refs., 4 tabs., 6 figs

  4. Nova frequency conversion and focusing system

    International Nuclear Information System (INIS)

    Summers, M.A.; Seppala, L.G.; Williams, J.D.

    1985-01-01

    New developments in crystal array technology provided significant improvements in the mechanical design and optical performance of the Nova 2 omega/3 omega array hardware. The final Nova array configuration was tested on the Novette laser and on the first arm of Nova. Ten Nova 2 omega/3 omega crystal arrays were assembled and tested for crystal alignment and wave front distortion before installation on the Nova target chamber. Ten Nova focus lens positioners were assembled and tested last year. The positioning accuracy and repeatability of each assembly were evaluated before installation on the target chamber. A cylindrical focusing system was also developed for installation in the Nova lens positioner assembly. Finally, 10 completed frequency conversion and focusing systems were activated

  5. Radiation damping in focusing-dominated systems

    International Nuclear Information System (INIS)

    Huang, Zhirong; Chen, Pisin; Ruth, R.D.

    1995-01-01

    A quasi-classical method is developed to calculate the radiation damping of a relativistic particle in a straight, continuous focusing system. In one limiting case where the pitch angle of the particle θ p is much larger than the radiation opening angle 1/γ, the radiation power spectrum is similar to synchrotron radiation and the relative damping rate of the transverse action is proportional to the relative energy loss rate. In the other limiting case where θ p much-lt 1/γ, the radiation is dipole in nature and the relative damping rate of the transverse action is energy-independent and is much faster than the relative energy rate. Quantum excitation to the transverse action is absent in this focusing channel. These results can be extended to bent systems provided that the focusing field dominates over the bending field

  6. Focus Groups as Transformative Spiritual Encounters

    Directory of Open Access Journals (Sweden)

    Sharon Moloney PhD

    2011-03-01

    Full Text Available Focus groups are a valuable method for exploring the construction and negotiation of meanings. In her doctoral research the author explored how Australian women's experiences of menstruation, birth, and spirituality are invested with meaning and how that meaning influences and shapes those experiences. The focus group has been described as a potentially liminal space, which enables the discussion of taboo subjects by breaking the ice and giving people permission to comment. In addition, she discovered that the groups could be occasions of empowerment and transformation for both participants and researcher. In a way that far exceeded her expectations, the group format was ideally suited to feminist research and the organic inquiry methodology she used. Some groups became deeply spiritual encounters that were nourishing and transformative for all. This article explores how focus groups can be vehicles of spiritual transformation, examining one group in particular to highlight the points raised.

  7. Bringing customer focus to power generation

    Energy Technology Data Exchange (ETDEWEB)

    Mahoney, J.V. [USGen Power Services (United States)

    1997-02-01

    The restructuring of the power generation industry and the impact it will have on a company`s success was discussed. Some companies are following one of three distinct strategies for survival, the GENCO, MARKETCO and TRADECO. The GENCO focuses on aggregating low cost, kick butt generation assets that could be either regionally concentrated or geographically distributed. The TRADECO invests in few, or even no, assets. Its only objective is to maximize net income. The MARKETCO structure focuses on understanding and meeting customers` needs. The MARKETCO puts as much value in aggregating `load` as it does on assets. It was suggested that the MARKETCO was the quickest path to success in the restructured electric industry, since it is plainly evident that in the New Millenium the customer will be king, and companies will not survive unless they focus the majority of their efforts on the customer.

  8. Final Focus Systems in Linear Colliders

    International Nuclear Information System (INIS)

    Raubenheimer, Tor

    1998-01-01

    In colliding beam facilities, the ''final focus system'' must demagnify the beams to attain the very small spot sizes required at the interaction points. The first final focus system with local chromatic correction was developed for the Stanford Linear Collider where very large demagnifications were desired. This same conceptual design has been adopted by all the future linear collider designs as well as the SuperConducting Supercollider, the Stanford and KEK B-Factories, and the proposed Muon Collider. In this paper, the over-all layout, physics constraints, and optimization techniques relevant to the design of final focus systems for high-energy electron-positron linear colliders are reviewed. Finally, advanced concepts to avoid some of the limitations of these systems are discussed

  9. The plasma focus - numerical experiments leading technology

    International Nuclear Information System (INIS)

    Saw, S.H.; Lee, S.

    2013-01-01

    Numerical experiments on the plasma focus are now used routinely to assist design and provide reference points for diagnostics. More importantly guidance has been given regarding the implementation of technology for new generations of plasma focus devices. For example intensive series of experiments have shown that it is of no use to reduce static bank inductance L0 below certain values because of the consistent loading effects of the plasma focus dynamics on the capacitor bank. Thus whilst it was thought that the PF1000 could receive major benefits by reducing its bank inductance L 0 , numerical experiments have shown to the contrary that its present L 0 of 30 nH is already optimum and that reducing L 0 would be a very expensive fruitless exercise. This knowledge gained from numerical experiments now acts as a general valuable guideline to all high performance (ie low inductance) plasma focus devices not to unnecessarily attempt to further lower the static inductance L 0 . The numerical experiments also show that the deterioration of the yield scaling law (e.g. the fusion neutron yield scaling with storage energy) is inevitable again due to the consistent loading effect of the plasma focus, which becomes more and more dominant as capacitor bank impedance reduces with increasing capacitance C 0 as storage energy is increased. This line of thinking has led to the suggestion of using higher voltages (as an alternative to increasing C 0 ) and to seeding of Deuterium with noble gases in order to enhance compression through thermodynamic mechanisms and through radiation cooling effects of strong line radiation. Circuit manipulation e.g. to enhance focus pinch compression by current-stepping is also being numerically experimented upon. Ultimately however systems have to be built, guided by numerical experiments, so that the predicted technology may be proven and realized. (author)

  10. Focus measurement of electron linear accelerator

    International Nuclear Information System (INIS)

    Su Zhijun; Xin Jian; Jia Qinglong

    2007-01-01

    Many personal factors would influence the result of the focus measurement of linear accelerator using the conventional sandwich method. This paper presents a modified method which applies a film scanning meter to scan the X-ray image film got by sandwich method for obtaining a greyscale distribution, then the full width at half maximum value of greyscale distribution represents the focus size. The method can eliminates disadvantage influence from accelerator radiant field asymmetry by quadratic polynomial fitting and measures peak width at half height instead of stripe statistic. (authors)

  11. CY15 Livermore Computing Focus Areas

    Energy Technology Data Exchange (ETDEWEB)

    Connell, Tom M. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Cupps, Kim C. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); D' Hooge, Trent E. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Fahey, Tim J. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Fox, Dave M. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Futral, Scott W. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Gary, Mark R. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Goldstone, Robin J. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Hamilton, Pam G. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Heer, Todd M. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Long, Jeff W. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Mark, Rich J. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Morrone, Chris J. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Shoopman, Jerry D. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Slavec, Joe A. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Smith, David W. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Springmeyer, Becky R [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Stearman, Marc D. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Watson, Py C. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States)

    2015-01-20

    The LC team undertook a survey of primary Center drivers for CY15. Identified key drivers included enhancing user experience and productivity, pre-exascale platform preparation, process improvement, data-centric computing paradigms and business expansion. The team organized critical supporting efforts into three cross-cutting focus areas; Improving Service Quality; Monitoring, Automation, Delegation and Center Efficiency; and Next Generation Compute and Data Environments In each area the team detailed high level challenges and identified discrete actions to address these issues during the calendar year. Identifying the Center’s primary drivers, issues, and plans is intended to serve as a lens focusing LC personnel, resources, and priorities throughout the year.

  12. Foil focusing of relativistic electron beams

    Energy Technology Data Exchange (ETDEWEB)

    Ekdahl, Jr., Carl August [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

    2017-10-26

    When an intense relativistic electron beams (IREB) passes through a grounded metal foil, the transverse electric field due to the beam space charge is locally shorted out, and the beam is focused by the magnetic field of its current. The effect can be treated as focusing by a thin lens with first order aberration. Expressions for the focal length and aberration coefficient of the equivalent thin lens are developed in this note. These are then applied to practical examples representative of IREB research at Los Alamos National Laboratory.

  13. ECONOMIC STRATEGY CREATED THROUGH THEORY FOCUSED PLANNING

    Directory of Open Access Journals (Sweden)

    Dumitru-Alexandru Bodislav

    2011-06-01

    Full Text Available The research done for this article is following the elaboration of a moldable model on the actual economic context, in which there are considered continuous learning elements on facts and commercial niches, evaluating a business starting from causality diagram and structuring its processes. Analyzing the evolution of a business and on the market in which they are deploying their activity through quantitative and qualitative measurement methods focused on trends. Testing hypotheses and business suppositions that are the main engine of theory focused on planning, a model of creating a strategic management process that will be developed in this article.

  14. SKEW QUADRUPOLE FOCUSING LATTICES AND APPLICATIONS

    International Nuclear Information System (INIS)

    Parker, B.

    2001-01-01

    In this paper we revisit using skew quadrupole fields in place of traditional normal upright quadrupole fields to make beam focusing structures. We illustrate by example skew lattice decoupling, dispersion suppression and chromatic correction using the neutrino factory Study-II muon storage ring design. Ongoing BNL investigation of flat coil magnet structures that allow building a very compact muon storage ring arc and other flat coil configurations that might bring significant magnet cost reduction to a VLHC motivate our study of skew focusing

  15. A self-focusing mercury jet target

    CERN Document Server

    Johnson, C

    2002-01-01

    Mercury jet production targets have been studied in relation to antiproton production and, more recently, pion production for a neutrino factory. There has always been a temptation to include some self-focusing of the secondaries by passing a current through the mercury jet analogous to the already proven lithium lens. However, skin heating of the mercury causes fast vaporization leading to the development of a gliding discharge along the surface of the jet. This external discharge can, nevertheless, provide some useful focusing of the secondaries in the case of the neutrino factory. The technical complications must not be underestimated.

  16. Neutron emission from deuterium plasma focus

    International Nuclear Information System (INIS)

    Antanasijevic, R.; Banjanac, R.; Dragic, A.; Djordjevic, D.; Joksimovic, D.; Maric, Z.; Udovicic, V.; Vukovic, J.

    1998-01-01

    The anisotropy of emitted neutrons is investigated on a small 'Mather-type' plasma focus device (PF). This problem is of importance for determining the nature of the fusion reaction mechanisms. Mica detectors together with thick uranium foils were used for both detection and angular distribution measurements of the neutrons. Previously, the annealing of the detectors was done and measured after the irradiation with neutrons from Am-Be source. Also, annealing ability of H-plasma focus has been tested. Geometry of detectors in both experiments was the same. (authors)

  17. Radiation reaction in a continuous focusing channel

    International Nuclear Information System (INIS)

    Huang, Z.; Chen, P.; Ruth, R.D.

    1995-01-01

    We show that the radiation damping rate of the transverse action of a particle in a straight, continuous focusing system is independent of the particle energy, and that no quantum excitation is induced. This absolute damping effect leads to the existence of a transverse ground state to which the particle inevitably decays and yields the minimum beam emittance that one can ever attain, γε min =ℎ/2mc, limited only by the uncertainty principle. Because of adiabatic invariance, the particle can be accelerated along the focusing channel in its ground state without any radiation energy loss

  18. International Focus: Highlighting APPA Members Worldwide

    Science.gov (United States)

    Glazner, Steve, Comp.

    2011-01-01

    While most APPA member institutions are located in the United States and Canada, there are also 45 of member institutions located internationally--from Australia and New Zealand to Southeast Asia to the Middle East to Europe. This article focuses on four of its international members: (1) American University of Kuwait (AUK); (2) American University…

  19. Content-Focused Coaching: Five Key Practices

    Science.gov (United States)

    Gibbons, Lynsey K.; Cobb, Paul

    2016-01-01

    Many districts are using content-focused coaching as a strategy to provide job-embedded support to teachers. However, the current coaching literature provides little guidance on what coaches need to know and be able to do to engage teachers in activities that will support their development of ambitious instructional practices. Furthermore, little…

  20. Magnetohydrodynamic studies of the strong Focus device

    International Nuclear Information System (INIS)

    Vezin, Robert

    1971-01-01

    The POTTER magnetohydrodynamic code is used. It consists of a two-dimensional fluid model with two temperatures Te, Ti and transverse transport coefficients for a fully ionized plasma. Applied to the FOCUS geometry used at Limeil, it gives temperatures consistent with the BENNETT law but much lower than those evaluated experimentally by the X-ray absorbing foils technique. (author) [fr

  1. Training Manual. Focused Observations: Nonverbal Teaching Behavior.

    Science.gov (United States)

    Bradley, Banks; And Others

    Nonverbal teacher behavior is recognized as an important factor in establishing a positive social climate in the classroom. A feedback and analysis instrument is presented focusing on specific nonverbal teacher behaviors. These behaviors--facial expressions, gestures, body movements, and idiosyncratic characteristics--are categorized as either…

  2. Science Education at Arts-Focused Colleges

    Science.gov (United States)

    Oswald, W. Wyatt; Ritchie, Aarika; Murray, Amy Vashlishan; Honea, Jon

    2016-01-01

    Many arts-focused colleges and universities in the United States offer their undergraduate students coursework in science. To better understand the delivery of science education at this type of institution, this article surveys the science programs of forty-one arts-oriented schools. The findings suggest that most science programs are located in…

  3. Careers in focus library and information science

    CERN Document Server

    2011-01-01

    Careers in Focus: Library and Information Science, Second Edition profiles 19 careers for professionals interested in this field. Job profiles include:. -Acquisitions librarians. -Book conservators. -Children's librarians. -Corporate librarians. -Film and video librarians. -Law librarians. -Library assistants. -Library media specialists. -Medical librarians. -Research assistants.

  4. The stabilisation of final focus system

    Indian Academy of Sciences (India)

    The StaFF (stabilisation of final focus) system will use interferometers to monitor the relative ... quadrupole magnets will be the most demanding application, where mutual and beam- ... interferometers to measure lines of a geodetic network to record relative motion between two beam ... coupled interferometer design.

  5. GRI: focusing on the evolving violent universe

    DEFF Research Database (Denmark)

    Knodlseder, J.; von Ballmoos, P.; Frontera, F.

    2009-01-01

    The gamma-ray imager (GRI) is a novel mission concept that will provide an unprecedented sensitivity leap in the soft gamma-ray domain by using for the first time a focusing lens built of Laue diffracting crystals. The lens will cover an energy band from 200-1,300 keV with an effective area reach...... processes in the universe....

  6. Accelerating and focusing structures for PIGMI

    International Nuclear Information System (INIS)

    Swenson, D.A.; Bush, E.D. Jr.; Holsinger, R.F.; Manca, J.J.; Saito, N.; Stovall, J.E.

    1977-01-01

    The National Cancer Institute is supporting a program of accelerator development at the Los Alamos Scientific Laboratory aimed at the extension of proton linac technologies to produce the most suitable Pion Generator for Medical Irradiations (PIGMI). An optimized design of a pion generator suitable for a radiotherapy program at a major medical center has been established, consisting of a 250-keV injector, followed by a 35-meter-long drift-tube linac that accelerates the proton beam to 150 MeV, and an 85-meter-long coupled-cavity linac that accelerates the beam to its final energy of 650 MeV, where the average beam current of 100 microamperes impinges on one or more targets producing abundant quantities of π - mesons for radiotherapeutic applications. A number of extensions to proton linac technology are being pursued under the PIGMI program at LASL. A discussion is given of recent developments in three areas relevant to the acceleration and focusing of proton beams, namely, the alternating phase focused (APF) linac structure, the disk and washer linac structure, and small permanent magnet quadrupole lenses. The APF linac structure is being developed for the acceleration and focusing role from the injection energy of 250 keV to a few MeV, where a transition is made to a permanent magnet quadrupole focused linac structure. The disk and washer linac structure is under consideration for the high velocity portion of the design

  7. Gas ionization by focused laser beams

    International Nuclear Information System (INIS)

    Brito, A.L. de.

    1984-01-01

    It is shown that the effect of line broadening by focusing may considerably contribute to the observed laser-induced ionization of gases when the ionization energy of the gas molecules is well above the mean photon energy of the laser radiation. (Author) [pt

  8. Focal CT abnormality and epileptogenic focus

    International Nuclear Information System (INIS)

    Yagi, Kazuichi; Mihara, Tadahiro; Tottori, Takayasu; Matsuda, Kazumi; Watanabe, Yutaka; Seino, Masakazu

    1989-01-01

    In 31 patients with temporal lobe epilepsy, the precise site of epileptogenic focus was determined by means of a depth EEG recording as one of the presurgical evaluations. In 13 patients, a CT scan revealed focal lesions; 7 in the left temporal lobe and 6 in the right temporal lobe. In 5 of the 7 patients and in 5 of the 6 patients the epileptogenic foci were determined in the temporal lobe on the side of a CT lesion. However, in 2 of the patients with a CT lesion in the left temporal lobe, independent epileptogenic foci were found in both the temporal lobes, and in the other patient with a CT lesion in the right temporal lobe, they were found in the right frontal and left temporal lobes. Thus, the CT lesions agreed in lateralization and focality with the epileptogenic foci in 10 of the 13 patients (77%), but they disagreed in 3 (23%). A CT lesion disclosed in the temporal lobe does not necessarily indicate the side and/or site where the epileptogenic focus may be localized. Although exceptions may be made, spatial disagreement was exemplified between the CT lesion and epileptogenic focus. Therefore, extreme caution has to be taken on the side and/or site of the epileptogenic focus when functional surgical indication is to be made. (author)

  9. Proximity focusing RICH with TOF capabilities

    International Nuclear Information System (INIS)

    Korpar, S.; Adachi, I.; Fujita, K.; Fukushima, T.; Gorisek, A.; Hayashi, D.; Iijima, T.; Ikado, T.; Ishikawa, T.; Kawai, H.; Kozakai, Y.; Krizan, P.; Kuratani, A.; Mazuka, Y.; Nakagawa, T.; Nishida, S.; Ogawa, S.; Pestotnik, R.; Seki, T.; Sumiyoshi, T.; Tabata, M.; Unno, Y.

    2007-01-01

    A proximity focusing RICH counter with a multi-channel micro-channel plate (MCP) PMT was tested as a time-of-flight counter. Cherenkov photons emitted in the radiator medium as well as in the entrance window of the PMT were used for the time-of-flight measurement, and an excellent performance of the counter could be demonstrated

  10. Fundamental Movement Skills: An Important Focus

    Science.gov (United States)

    Barnett, Lisa M.; Stodden, David; Cohen, Kristen E.; Smith, Jordan J.; Lubans, David Revalds; Lenoir, Matthieu; Iivonen, Susanna; Miller, Andrew D.; Laukkanen, Arto; Dudley, Dean; Lander, Natalie J.; Brown, Helen; Morgan, Philip J.

    2016-01-01

    Purpose: Recent international conference presentations have critiqued the promotion of fundamental movement skills (FMS) as a primary pedagogical focus. Presenters have called for a debate about the importance of, and rationale for teaching FMS, and this letter is a response to that call. The authors of this letter are academics who actively…

  11. Shape from focus for large image fields

    Czech Academy of Sciences Publication Activity Database

    Pavlíček, Pavel; Hamarová, Ivana

    2015-01-01

    Roč. 54, č. 33 (2015), s. 9747-9751 ISSN 1559-128X R&D Projects: GA ČR GA13-12301S Institutional support: RVO:68378271 Keywords : shape from focus * large image fields * optically rough surface Subject RIV: BH - Optics , Masers, Lasers Impact factor: 1.598, year: 2015

  12. X-ray focusing using capillary arrays

    International Nuclear Information System (INIS)

    Nugent, K.A.; Chapman, H.N.

    1990-01-01

    A new form of X-ray focusing device based on glass capillary arrays is presented. Theoretical and experimental results for array of circular capillaries and theoretical and computational results for square hole capillaries are given. It is envisaged that devices such as these will find wide applications in X-ray optics as achromatic condensers and collimators. 3 refs., 4 figs

  13. SERPUKHOV: Focusing particles by a crystal

    International Nuclear Information System (INIS)

    Anon.

    1991-01-01

    With several Laboratories having shown how bent crystals can be used to steer particle beams, a team working at the Institute for High Energy Physics (IHEP) at Serpukhov, near Moscow, has shown how these crystals can also be used to focus particle beams

  14. Optimizing Monochromatic Focusing on ThALES

    Czech Academy of Sciences Publication Activity Database

    Čermák, P.; Boehm, M.; Kulda, J.; Roux, S.; Hiess, A.; Steffens, P.; Šaroun, Jan

    2014-01-01

    Roč. 82, A (2014), SA026 ISSN 0031-9015 Institutional support: RVO:61389005 Keywords : Monte Carlo ray-tracing * inelastic neutron scattering * Triple-Axis spectrometer * monochromatic focusing Subject RIV: BM - Solid Matter Physics ; Magnetism Impact factor: 1.585, year: 2014

  15. Revitalize Electrical Program with Renewable Energy Focus

    Science.gov (United States)

    Karns, Robert J.

    2012-01-01

    Starting a renewable energy technology (RET) program can be as simple as shifting the teaching and learning focus of a traditional electricity program toward energy production and energy control systems. Redirecting curriculum content and delivery to address photovoltaic solar (PV solar) technology and small wind generation systems is a natural…

  16. Capability, Governance and Nanotechnology : Focus on India ...

    International Development Research Centre (IDRC) Digital Library (Canada)

    Nanotechnology is the study and manipulation of matter on an ultra-small scale, generally in the range of 1-100 nanometres (1 metre = 1 billion nanometres). Like biotechnology, nanotechnology has the potential to bring huge benefits to the poor, but also huge costs. Focusing on India, this project will examine the ...

  17. Summary report on focusing HTGR technology programs

    International Nuclear Information System (INIS)

    The program effort to focus technology development activities consists of work in three areas: the identification of Reference Plant Options; the identification of design data needs and supporting program requirements for these plants; and the development of management plans and tools consistent with the execution of candidate systems

  18. Beam acceleration in plasma focus device

    Energy Technology Data Exchange (ETDEWEB)

    Antanasijevic, R.; Banjanac, R.; Dragic, A.; Maric, Z.; Stanojevic, J.; Udovicic, V. E-mail: udovicic@atom.phy.bg.ac.yu; Vukovic, J

    2001-06-01

    The proton beam emission from the small 8 kJ plasma focus device operated with the H{sub 2} filling was analyzed. Maximum energy and yield were obtained using NTD. The fast protons were registered with the energy up to 500 keV using the polycarbonate absorbers with the different thickness.

  19. Beam acceleration in plasma focus device

    International Nuclear Information System (INIS)

    Antanasijevic, R.; Banjanac, R.; Dragic, A.; Maric, Z.; Stanojevic, J.; Udovicic, V.; Vukovic, J.

    2001-01-01

    The proton beam emission from the small 8 kJ plasma focus device operated with the H 2 filling was analyzed. Maximum energy and yield were obtained using NTD. The fast protons were registered with the energy up to 500 keV using the polycarbonate absorbers with the different thickness

  20. Welcome Families by Focusing on Strengths

    Science.gov (United States)

    Minkel, Justin

    2017-01-01

    Families of struggling students, this teacher in a high-poverty school knows, feel defensive and hurt when communications with their child's school focus mainly on that child's deficits. This is especially true for families from poverty or immigrant backgrounds--and affirming the latter families is important in the current climate of hostility…

  1. Invited paper: Plasma focus in China

    International Nuclear Information System (INIS)

    Jinji, Y.

    1983-01-01

    Plasma focus research in China began in the seventies. There are now 3 devices in two institutions, Tsinghua University in Beijing and the Institute of Mining and Metallurgy in Changsha. The research works can be divided into two groups: the engineering problems related to plasma focus devices and the plasma phenomena and process of the focus. Under the first subject, insulation and plasma spark gaps are studied. By casting silicon rubber onto the ends of the transmission cable, the length of insulation can be appreciably reduced. With the method of simulating charges, the electric field distribution of a field distortion type spark gap was calculated. Comparison of the field distribution before and after triggering was represented. It shows that the electric field strength of the gap after triggering may reach 14-80 times as high as that before triggering. Thus the characteristic of the gap may be improved remarkably. In respect of the phenomena of the plasma focus, neutron emission and X-ray emission were measured. It was shown that the proportion of X-ray with higher energy depends upon the material of the inner electrode. Two kinds of stud materials, tungsten and molybendum, were adopted. Measured results of the distribution of X-ray energy were represented respectively for the two materials used. Evidently, the distribution changed with the inserted materials

  2. Organisational Change: A Solution-Focused Approach

    Science.gov (United States)

    Morgan, Gavin

    2016-01-01

    This study investigates the effectiveness of a solution-focused approach to organisational change. Planning Alternative Tomorrows with Hope (PATH) is an intervention more commonly applied to individuals. In this study the intervention is used with groups of people working in educational organisations to help manage the change process. The approach…

  3. Professional Development: Focusing on Transition. Issue Brief

    Science.gov (United States)

    de Azúa, Ramón L.; Keleher, Julia

    2017-01-01

    In 2017, the National Technical Assistance Center for the Education of Neglected or Delinquent Children and Youth (NDTAC) released its first in a series of professional development briefs that focus on the professional development needs and interests of Neglected or Delinquent (N or D) State coordinators, correctional educators, and providers of…

  4. Synthesis of focusing-and-deflection columns

    International Nuclear Information System (INIS)

    Szilagyi, M.; Mui, P.H.

    1995-01-01

    Szilagyi and Szep have demonstrated that focusing lenses of high performances can be constructed from a column of circular plate electrodes. Later, Szilagyi modified that system to include dipole, quadrupole, and octupole components by partitioning each plate into eight equal sectors. It has already been shown that the additional quadrupole components can indeed bring about substantial improvements in the focusing of charged particle beams. In this article, that design procedure is expanded to construct columns capable of both focusing and deflecting particle beams by just introducing additional dipole components. In this new design, the geometry of the system remains unchanged. The only extra complication is the demand for more individual controls of the sector voltages. Two sample designs, one for negative ions and one for electrons, are presented showing that in both cases a ±2.3 mrad diverging beam can be focused down to a spot of less than 50 nm in radius over a scanning circular area of radius 0.25 mm. The details of the two systems are given in Sec. IV along with the source conditions. The performance of the negative ion system is found to be comparable to the published data. For the relativistic electron system, the interaction of individual components to reduce various aberrations is investigated. copyright 1995 American Vacuum Society

  5. Focus: Composition and Language Study, K-6.

    Science.gov (United States)

    Stewart, Donald, Ed.

    1974-01-01

    This issue of "Kansas English" focus on composition and language study, kindergarten through grade six. The articles and authors are "Evaluating Process and Product in Children's Writing" by Robert L. Hillerich, "Written Language Development and Instruction of Elementary School Children" by Lester S. Golub, "From a Reading Desk" by Myrline…

  6. Computational numerical modelling of plasma focus

    International Nuclear Information System (INIS)

    Brollo, Fabricio

    2005-01-01

    Several models for calculation of the dynamics of Plasma Focus have been developed. All of them begin from the same physic principle: the current sheet run down the anode length, ionizing and collecting the gas that finds in its way.This is known as snow-plow model.Concerning pinch's compression, a MHD model is proposed.The plasma is treated as a fluid , particularly as a high ionized gas.However, there are not many models that, taking into account thermal equilibrium inside the plasma, make approximated calculations of the maximum temperatures reached in the pinch.Besides, there are no models which use those temperatures to estimate the termofusion neutron yield for the Deuterium or Deuterium-Tritium gas filled cases.In the PLADEMA network (Dense Magnetized Plasmas) a code was developed with the objective of describe the plasma focus dynamics, in a conceptual engineering stage.The codes calculates the principal variables (currents, time to focus, etc) and estimates the neutron yield in Deuterium-filled plasma focus devices.It can be affirmed that the code's experimental validation, in its axial and radial stages, was very successfully. However, it was accepted that the compression stage should be formulated again, to find a solution for a large variation of a parameter related with velocity profiles for the particles trapped inside the pinch.The objectives of this work can be stated in the next way : - Check the compression's model hypothesis. Develop a new model .- Implement the new model in the code. Compare results against experimental data of Plasma Focus devices from all around the world [es

  7. Numerical experimentation on focusing time and neutron yield in GN1 plasma focus machine

    International Nuclear Information System (INIS)

    Singh, Arwinder; Lee, Sing; Saw, S.H.

    2014-01-01

    In this paper, we have shown how we have fitted Lee's six phase model code to analyze the current waveform of the GN1 plasma focus machine working in deuterium gas. The Lee's 6-phase model codes was later configured to work between 0.5 to 6 Torr and the results of both focusing time and neutron yield was then compared with the published experimental results. The final results indicate that Lee's code, gives realistic plasma dynamics and focus properties together with a realistic neutron yield for GN1 plasma focus, without the need of any adjustable parameters, needing only to fit the computed current trace to a measured current trace. (author)

  8. Frontend electronics for high-precision single photo-electron timing using FPGA-TDCs

    Energy Technology Data Exchange (ETDEWEB)

    Cardinali, Matteo [Helmholtz Institut Mainz (Germany); Collaboration: PANDA Cherenkov-Collaboration

    2014-07-01

    The next generation of high-luminosity experiments requires excellent Particle Identification (PID) detectors which calls for Imaging Cherenkov counters with fast electronics to cope with the expected data rates. The planned PANDA experiment at FAIR expects average interaction rates of 20 MHz. A Barrel DIRC will provide PID in the central region of the Target Spectrometer. A single photo-electron timing resolution of better than 100 ps is projected for the Barrel DIRC to disentangle the complicated patterns created by the focusing optics on the image plane. The typically large amount of readout channels (approx 15,000 in case of the PANDA Barrel DIRC) places non-negligible limits on size and power consumption of the Front-End Electronics (FEE). The proposed design is based on the TRBv3 readout using FPGA-TDCs with a precision better than 20 ps RMS and custom FEE with high-bandwidth pre-amplifiers and fast discriminators. Two types of FEE cards optimised for reading out 64-channel Photonis Planacon MCP-PMTs were tested: one based on the NINO ASIC developed for the ALICE RPC readout and the other, called PaDiWa, using FPGA-based discriminators. Both types of FEE cards were tested with a small DIRC prototype comprising a radiator bar with focusing lens and an oil-filled expansion volume instrumented with 6 Planacon 64-channel MCP-PMTs. In the presentation the result of a test experiment performed at MAMI B, Mainz, are addressed.

  9. Magnetic focusing in triangular electron billiards

    DEFF Research Database (Denmark)

    Bøggild, Peter; Kristensen, A.; Lindelof, Poul Erik

    1999-01-01

    The classical ballistic magnetotransport in triangular electron billiards fabricated in a high mobility GaAs heterostructure has been studied at 4.2 K. The sample geometry may be viewed as a double-slit structure with a skewed injection angle. We observe a striking cancellation of the magnetic...... focusing spectrum compared to the case of a perpendicular injection angle. From numerical and analytical analysis, we confirm that the quenching is a fundamental geometrical effect, and identify two mechanisms responsible for the anomaly. The focusing spectrum of the considered skewed geometry...... is remarkably sensitive to the angular distribution of injected electrons as well as the overall injection angle. [S0163-1829(99)06619-9]....

  10. Plasma devices for focusing extreme light pulses

    International Nuclear Information System (INIS)

    Fuchs, J.; Gonoskov, A.A.; Nakatsutsumi, M.; Nazarov, W.; Quere, F.; Sergeev, A.M.; Yan, X.Q.

    2014-01-01

    Since the inception of the laser, there has been a constant push toward increasing the laser peak intensity, as this has lead to opening the exploration of new territories, and the production of compact sources of particles and radiation with unprecedented characteristics. However, increasing the peak laser intensity is usually performed by enhancing the produced laser properties, either by lowering its duration or increasing its energy, which involves a great level of complexity for the laser chain, or comes at great cost. Focusing tightly is another possibility to increase the laser intensity, but this comes at the risk of damaging the optics with target debris, as it requires their placement in close proximity to the interaction region. Plasma devices are an attractive, compact alternative to tightly focus extreme light pulses and further increase the final laser intensity. (authors)

  11. Dense plasma focus - a literature review

    International Nuclear Information System (INIS)

    Tendys, J.

    1976-01-01

    The dense plasma focus (DPF) is a convenient source of short, intense neutron pulses, and dense, high temperature plasma. This review of the literature on the DPF indicates that its operation is still not understood, and attempts to show where the present data is either inadequate or inconsistent. Because the plasma conditions and neutron and x-ray fluxes vary from shot to shot, it is maintained that, to resolve inconsistencies in the present data, spectra need to be measured with energy and time resolution simultaneously, and cannot be built up from a large number of shots. Time resolutions of the order of 1 nsec for pulse lengths of about 100 nsec make these requirements especially difficult. Some theoretical models are presented for the neutron output and its spectrum, but no self-consistent description of the plasma in the focus region is likely for some time. (author)

  12. Missing data imputation: focusing on single imputation.

    Science.gov (United States)

    Zhang, Zhongheng

    2016-01-01

    Complete case analysis is widely used for handling missing data, and it is the default method in many statistical packages. However, this method may introduce bias and some useful information will be omitted from analysis. Therefore, many imputation methods are developed to make gap end. The present article focuses on single imputation. Imputations with mean, median and mode are simple but, like complete case analysis, can introduce bias on mean and deviation. Furthermore, they ignore relationship with other variables. Regression imputation can preserve relationship between missing values and other variables. There are many sophisticated methods exist to handle missing values in longitudinal data. This article focuses primarily on how to implement R code to perform single imputation, while avoiding complex mathematical calculations.

  13. Energy coupling in the plasma focus

    International Nuclear Information System (INIS)

    Wainwright, T.E.; Pickles, W.L.; Sahlin, H.L.; Price, D.F.

    1979-01-01

    Experiments have been performed with a 125-kJ plasma focus to investigate mechanisms for rapid coupling of inductively-stored energy into plasmas. The coupling can take place through the formation of an electron or ion beam that deposits its energy in a target or directly by the penetration of the magnetic field into a resistive plasma. Some preliminary results from experiments of both types are described. The experiments use a replaceable conical anode tip that is intended to guide the focus to within a few millimeters of the axis, where it can suddenly deliver energy either to a small target or to particles that are accelerated. X-ray and fast-ion diagnostics have been used to study the effects

  14. Plasma focus system: Design, construction and experiments

    International Nuclear Information System (INIS)

    Alacakir, A.; Akguen, Y.; Boeluekdemir, A. S.

    2007-01-01

    The aim of this work is to construct a compact experimental system for fusion research. The design, construction and experiments of the 3 kJ Mather type plasma focus machine is described. This machine is established for neutron yield and fast neutron radiography by D-D reaction which is given by D + D→ 3 He (0.82 MeV) + n (2.45 MeV) . Investigation of the geometry of plasma focus machine in the presence of high voltage drive and vacuum system setup is shown. 108 neutron per pulse and 200 kA peak current is obtained for many shots. Scintillator screen for fast neutron imaging, sensitive to 2.45 MeV neutrons, is also manufactured in our labs. Structural neutron shielding computations for safety is also completed

  15. Compression Models for Plasma Focus Devices

    International Nuclear Information System (INIS)

    Gonzalez, Jose; Calusse, Alejandro; Ramos, Ruben; Rodriguez Palomino, Luis

    2003-01-01

    Using a numerical model that calculates the dynamics of Plasma Focus devices, we compared the results of three different compression models of the plasma pinch.One of the main objectives in this area is to develop a simplified model to calculate the neutron production of Plasma Focus devices, to study the influence of the main parameters in this neutron yield.The dynamics is thoroughly studied, and the model predicts fairly well values such as maximum currents and times for pinch collapse.Therefore, we evaluate here different models of pinch compression, to try to predict the neutron production with good agreement with the rest of the variables involved.To fulfill this requirement, we have experimental results of neutron production as a function of deuterium filling pressure in the chamber, and typical values of other main variables in the dynamics of the current sheet

  16. Slice through an LHC focusing magnet

    CERN Multimedia

    Slice through an LHC superconducting quadrupole (focusing) magnet. The slice includes a cut through the magnet wiring (niobium titanium), the beampipe and the steel magnet yokes. Particle beams in the Large Hadron Collider (LHC) have the same energy as a high-speed train, squeezed ready for collision into a space narrower than a human hair. Huge forces are needed to control them. Dipole magnets (2 poles) are used to bend the paths of the protons around the 27 km ring. Quadrupole magnets (4 poles) focus the proton beams and squeeze them so that more particles collide when the beams’ paths cross. Bringing beams into collision requires a precision comparable to making two knitting needles collide, launched from either side of the Atlantic Ocean.

  17. Self-focusing of whistler waves

    Science.gov (United States)

    Karpman, V. I.; Kaufman, R. N.; Shagalov, A. G.

    1992-01-01

    The theory of axially symmetric self-focusing of whistler waves, based on the full system of Maxwell equations, is developed. The plasma is described by the magnetohydrodynamic equations including the ponderomotive force from RF field. The nonlinear Schrodinger equations (NSE) for arbitrary azimuthal modes of whistler waves are derived. It is shown that they differ from the NSE for a scalar field; this is connected with an intrinsic angular momentum due to the rotating polarization of whistlers. It is shown that the self-focusing, as described by the NSE, differs in its final stage from the results following the full set of Maxwell equations. The latter gives defocusing after sufficient narrowing of the initial wave beam, due to transformation of the trapped wave into a nontrapped branch which is not contained in the NSE description. The oscillatory character of the defocusing is demonstrated.

  18. Raman Amplification with a Flying Focus

    Science.gov (United States)

    Turnbull, D.; Bucht, S.; Davies, A.; Haberberger, D.; Kessler, T.; Shaw, J. L.; Froula, D. H.

    2018-01-01

    We propose a new laser amplifier scheme utilizing stimulated Raman scattering in plasma in conjunction with a "flying focus"—a chromatic focusing system combined with a chirped pump beam that provides spatiotemporal control over the pump's focal spot. Pump intensity isosurfaces are made to propagate at v =-c so as to be in sync with the injected counterpropagating seed pulse. By setting the pump intensity in the interaction region to be just above the ionization threshold of the background gas, an ionization wave is produced that travels at a fixed distance ahead of the seed. Simulations show that this will make it possible to optimize the plasma temperature and mitigate many of the issues that are known to have impacted previous Raman amplification experiments, in particular, the growth of precursors.

  19. Self-focusing in SF6

    International Nuclear Information System (INIS)

    Ackerhalt, J.R.; Galbraith, H.W.

    1981-01-01

    It is shown by explicit calculation of previously published quasicontinuum model that the molecular susceptibility rapidly approaches zero as higher excited states of the molecule become populated. Hence the overtones of the ν 3 -pumped mode are totally responsible for the self focusing effects in SF 6 . The ν 3 ladder contribution to the susceptibility is calculated. The vibrational model is a classical triply degenerate anharmonic oscillator in the Cartesian basis with the anharmonicity parameters chosen to be consistent with the latest spectroscopic analysis of the 3ν 3 overtone spectrum. The rotational structure is represented by a distribution of these oscillators where the distribution is chosen to correspond to the spectrum of the ν 3 fundamental. Good agreement is found with the 300 0 in self-focusing data of Nowak and Ham at CO 2 P(28), P(20) and P(10) in SF 6

  20. Focused-laser interferometric position sensor

    International Nuclear Information System (INIS)

    Friedman, Stephen J.; Barwick, Brett; Batelaan, Herman

    2005-01-01

    We describe a simple method to measure the position shifts of an object with a range of tens of micrometers using a focused-laser (FL) interferometric position sensor. In this article we examine the effects of mechanical vibration on FL and Michelson interferometers. We tested both interferometers using vibration amplitudes ranging from 0 to 20 μm. Our FL interferometer has a resolution much better than the diffraction grating periodicities of 10 and 14 μm used in our experiments. A FL interferometer provides improved mechanical stability at the expense of spatial resolution. Our experimental results show that Michelson interferometers cannot be used when the vibration amplitude is more than an optical wavelength. The main purpose of this article is to demonstrate that a focused-laser interferometric position sensor can be used to measure the position shifts of an object on a less sensitive, micrometer scale when the vibration amplitude is too large to use a Michelson interferometer

  1. Radio frequency focused interdigital linear accelerator

    Science.gov (United States)

    Swenson, Donald A.; Starling, W. Joel

    2006-08-29

    An interdigital (Wideroe) linear accelerator employing drift tubes, and associated support stems that couple to both the longitudinal and support stem electromagnetic fields of the linac, creating rf quadrupole fields along the axis of the linac to provide transverse focusing for the particle beam. Each drift tube comprises two separate electrodes operating at different electrical potentials as determined by cavity rf fields. Each electrode supports two fingers, pointing towards the opposite end of the drift tube, forming a four-finger geometry that produces an rf quadrupole field distribution along its axis. The fundamental periodicity of the structure is equal to one half of the particle wavelength .beta..lamda., where .beta. is the particle velocity in units of the velocity of light and .lamda. is the free space wavelength of the rf. Particles are accelerated in the gaps between drift tubes. The particle beam is focused in regions inside the drift tubes.

  2. Epileptogenic focus localization: a new approach

    Energy Technology Data Exchange (ETDEWEB)

    Tavares, Vânia [Institute of Biophysics and Biomedical Engineering, Faculty of Sciences of the University of Lisbon, Lisboa (Portugal); Ribeiro, André Santos [Institute of Biophysics and Biomedical Engineering, Faculty of Sciences of the University of Lisbon, Lisboa (Portugal); Centre for Neuropsychopharmacology, Division of Brain Sciences, Department of Medicine, Imperial College London, London (United Kingdom); Capela, Carlos; Cerqueira, Luís [Department of Neuroradiology, Centro Hospitalar Lisboa Central, Lisbon (Portugal); Ferreira, Hugo Alexandre [Institute of Biophysics and Biomedical Engineering, Faculty of Sciences of the University of Lisbon, Lisboa (Portugal)

    2015-05-18

    Epilepsy is one of the most important chronic neurological disorders worldwide affecting more than 50 million people of all ages. Among these, almost 20% of epilepsy cases are uncontrollable and have an unknown source of this abnormal electrical activity. Present techniques for the detection of epileptogenic foci include electroencephalography (EEG), positron emission tomography, and multimodal EEG/functional magnetic resonance imaging (fMRI), all with limitations in terms of spatial and temporal resolutions. In order to overcome some of those limitations a novel approach using fMRI alone was developed based on the hypotheses that the epileptogenic focus shows Blood Oxygen Level Dependent (BOLD) temporal profiles distinct from the remaining brain parenchyma during interictal activity and that the epileptogenic focus BOLD signals show lower complexity than healthy parenchyma. In this novel approach, bi-dimensional temporal clustering analysis, a data-driven technique, was used to identify brain regions with similar temporal profiles. Then, the BOLD signals of these regions were assessed regarding complexity using detrended fluctuation analysis and also using a modified multiscale entropy algorithm in order to identify which of those regions corresponded to epileptogenic tissue. In order to demonstrate the applicability of the developed method three epileptic patients were analyzed comprising two types of epilepsy: unilateral and bilateral temporal lobe epilepsies. The results showed that this method is able to detect the brain regions associated with epileptogenic tissue. The results also showed that the epileptogenic focus influences the dynamics of related brain networks. This could be a key factor in the applicability of this method to other epilepsy cases. Finally, new perspectives are envisioned concerning the use of this method in the medical care of epilepsy. In particular, by improving this method using simultaneous structural, functional, and metabolic

  3. New focusing analyser on IN12

    International Nuclear Information System (INIS)

    Schmidt, W.; Faak, B.

    1999-01-01

    Among several improvements and modifications the IN12 three-axis spectrometer for cold neutrons has been equipped with a new graphite analyzer with variable horizontal and fixed vertical focusing features. With this analyzer we could drastically improve the instrument performance and also meet the standards of a modern three-axis spectrometer. In this report we show construction details as well as experimental results which demonstrate the improvements. (author)

  4. SCIENTIFIC COMMUNICATION WITH A FOCUS ON SESAME

    CERN Document Server

    ahmad, sameem

    2017-01-01

    Scientific communication, the representation of CERN and raising awareness about science to a wide range of audiences is very important for the CERN communication teams. Having a physics background and an interest in science administration, communication and research, I was based in the International Relations sector, working in various groups and focusing on written communication. I gained experience in many aspects of scientific communications by finding out how CERN in represented in the press and media, other online forums and in outreach.

  5. Epileptogenic focus localization: a new approach

    International Nuclear Information System (INIS)

    Tavares, Vânia; Ribeiro, André Santos; Capela, Carlos; Cerqueira, Luís; Ferreira, Hugo Alexandre

    2015-01-01

    Epilepsy is one of the most important chronic neurological disorders worldwide affecting more than 50 million people of all ages. Among these, almost 20% of epilepsy cases are uncontrollable and have an unknown source of this abnormal electrical activity. Present techniques for the detection of epileptogenic foci include electroencephalography (EEG), positron emission tomography, and multimodal EEG/functional magnetic resonance imaging (fMRI), all with limitations in terms of spatial and temporal resolutions. In order to overcome some of those limitations a novel approach using fMRI alone was developed based on the hypotheses that the epileptogenic focus shows Blood Oxygen Level Dependent (BOLD) temporal profiles distinct from the remaining brain parenchyma during interictal activity and that the epileptogenic focus BOLD signals show lower complexity than healthy parenchyma. In this novel approach, bi-dimensional temporal clustering analysis, a data-driven technique, was used to identify brain regions with similar temporal profiles. Then, the BOLD signals of these regions were assessed regarding complexity using detrended fluctuation analysis and also using a modified multiscale entropy algorithm in order to identify which of those regions corresponded to epileptogenic tissue. In order to demonstrate the applicability of the developed method three epileptic patients were analyzed comprising two types of epilepsy: unilateral and bilateral temporal lobe epilepsies. The results showed that this method is able to detect the brain regions associated with epileptogenic tissue. The results also showed that the epileptogenic focus influences the dynamics of related brain networks. This could be a key factor in the applicability of this method to other epilepsy cases. Finally, new perspectives are envisioned concerning the use of this method in the medical care of epilepsy. In particular, by improving this method using simultaneous structural, functional, and metabolic

  6. Vision Trainer Teaches Focusing Techniques at Home

    Science.gov (United States)

    2015-01-01

    Based on work Stanford Research Institute did for Ames Research Center, Joseph Trachtman developed a vision trainer to treat visual focusing problems in the 1980s. In 2014, Trachtman, operating out of Seattle, released a home version of the device called the Zone-Trac. The inventor has found the biofeedback process used by the technology induces an alpha-wave brain state, causing increased hand-eye coordination and reaction times, among other effects

  7. A lumped parameter model of plasma focus

    International Nuclear Information System (INIS)

    Gonzalez, Jose H.; Florido, Pablo C.; Bruzzone, H.; Clausse, Alejandro

    1999-01-01

    A lumped parameter model to estimate neutron emission of a plasma focus (PF) device is developed. The dynamic of the current sheet is calculated using a snowplow model, and the neutron production with the thermal fusion cross section for a deuterium filling gas. The results were contrasted as a function of the filling pressure with experimental measurements of a 3.68 KJ Mather-type PF. (author)

  8. Project Management with IT Security Focus

    OpenAIRE

    Felician Alecu; Paul Pocatilu; Sergiu Capisizu

    2011-01-01

    The paper focus on the main key points related to the IT security project management. The most important lifecycle stages are identified: IT security project proposal definition, project organization, project planning, quality planning, project team organization, IT security project activities management and project closing. The most important success factors for IT security projects are the support of top-management, customer satisfaction, prevention over remediation and continuous progress....

  9. Simulation Of Gas Focused Liquid Jets

    OpenAIRE

    Zahoor, Rizwan

    2018-01-01

    The main aim of dissertation is to develop an experimentally verified computational fluid dynamic (CFD) model of micron-sized liquid jet, produced by an injection molded Gas Dynamic Virtual Nozzle (GDVN). In these nozzles, liquid jets are efficiently orientedly transporting mass and momentum. They are produced by intelligently projecting hydrodynamic focusing effect from a high-speed stream of a co-flowing lower density and lower viscosity gas on a stream of liquid from a feeding capillary. L...

  10. Charmed baryons photoproduced in FOCUS at Fermilab

    CERN Document Server

    Ratti, S P

    2001-01-01

    FOCUS collected over 7 * 10/sup 7/ triggers and more than 10/sup 6/ fully reconstructed charm particles in a photoproduction experiment at Fermilab. The experimental setup is an upgraded version of a multiparticle spectrometer used in the previous experiment E687. Data on charmed meson spectroscopy have been presented by F.L Fabbri in this Section. Here data on photoproduction of charmed baryons are presented.

  11. Architecture and Energy. Towards a broader Focus

    DEFF Research Database (Denmark)

    Lauring, Michael; Marsh, Rob

     Architecture and Energy. Towards a broader focus. By Michael Lauring and Rob Marsh   In typical new Danish dwellings build according to the standards of the Building Regulations 2008 approximately 35% of the primary energy use is related to heat consumption divided into 23% room heating and 12% ...... & Hacker (2008): Bygninger, Energi, Klima. Mod et nyt paradigme.  Statens Byggeforskningsinstitut (Danish Building Research Institute). [2] Marsh, Larsen, Lauring & Christensen (2006): Arkitektur og energi. Statens Byggeforskningsinstitut (Danish Building Research Instititute)....

  12. Focusing magnets for HIF based on racetracks

    Energy Technology Data Exchange (ETDEWEB)

    Martovetsky, N N; Manahan, R R

    2000-09-11

    Heavy Ion Fusion (HIF) is considered a promising path to a practical fusion reactor. A driver for a HIF reactor will require a large number of quadrupole arrays to focus heavy ion beams. A conceptual design, and trade off studies of the quadrupole array based on racetracks are presented. A comparison with a conventional shell magnet is given and advantages and disadvantages are discussed. A more detailed design of a single quadrupole for the High Current experiment (HCX) is presented and discussed.

  13. Results of Final Focus Test Beam

    Energy Technology Data Exchange (ETDEWEB)

    Walz, Dieter R

    2003-06-13

    The beam experiments of Final Focus Test Beam (FFTB) started in September 1993 at SLAC, and have produced a 1.7 {micro}m x 75 nm spot of 46 GeV electron beam. A number of new techniques involving two nanometer spot-size monitors have been developed. Several beam diagnostic/tuning schemes are applied to achieve and maintain the small spot. This experiment opens the way toward the nanometer world for future linear colliders.

  14. Ion Distribution Measurement In Plasma Focus

    International Nuclear Information System (INIS)

    Suryadi; Sunardi; Usada, Widdi; Purwadi, Agus; Zaenuri, Akhmad

    1996-01-01

    Measurement of the Argon ion distribution in plasma focus by using Faraday cup has been done. The intensity of ion beam followed the I Rn rule, n=1,02. In the operation condition of 0,8 mbar and 12,5 kV the current sheath spen 2.2 to 2.4 μsecond in the rundown phase. Cu ion was also been observed in the Faraday cup

  15. The Upgraded Plasma Focus Installation > - The Installation >

    International Nuclear Information System (INIS)

    Krokhin, O.N.; Nikulin, V.Ya.; Babenko, B.A.; Gorbunov, D.N.; Gurei, A.E.; Kalachev, N.V.; Kozlova, T.A.; Malafeev, Yu.S.; Polukhin, S.N.; Sychev, A.A.; Tikhomirov, A.A.; Tsybenko, S.P.; Volobuev, I.V.

    1999-01-01

    The paper presents the upgraded plasma focus installation > - the installation > and some preliminary experimental results. The total energy stored in capacity bank is now 400 kJ, current - 5 MA with the rise time 3.5 μs. The investigation is targeted on the study of near electrode processes and its influence on plasma dynamics in a special operating regime of Filippov type PF - Hard X-ray regime. (author)

  16. Understanding weight stigmatization: a focus group study.

    Science.gov (United States)

    Cossrow, N H; Jeffery, R W; McGuire, M T

    2001-01-01

    The purpose of this research was to investigate, in a nonclinical sample of adults, thoughts on and experiences with weight stigmatization. Focus groups were used to collect information. Participants were recruited through a newspaper advertisement and flyers posted in public places in Minneapolis and St. Paul. During the focus groups, participants were led in a discussion about their thoughts on weight stigmatization and personal experiences of being treated differently or poorly because of their weight. Six gender-specific focus groups consisted of 31 adult volunteers (17 women and 14 men). Perceptions of weight-based stereotypes and weight stigmatization and personal reports of having been treated differently or poorly owing to weight were measured. Participants reported a variety of experiences of being treated differently or poorly because of their weight. These included teasing, harassment, slurs and insults, negative judgments and assumptions, and perceived discrimination. Participants reported that such experiences occurred at home, among friends and strangers, at work, and in health care settings. Women reported a greater number and a greater variety of negative experiences than men. The results indicated that participants experienced weight-based stigmatization in many aspects of their lives. Awareness of these experiences may assist in the development of treatments for overweight individuals.

  17. Safety, training focus of combined organization

    Energy Technology Data Exchange (ETDEWEB)

    Toop, L.

    2006-03-15

    This article presented details of Enform, a company that coordinates safety programs and training for new employees in the oil and gas industry. Enform was created when the Petroleum Industry Training Services merged with the Canadian Petroleum Safety Council. The aim of Enform is to ensure continuous improvements in health and safety within the industry by reducing working injuries and promoting health and safety practices. The companies merged to eliminate duplication of services and allow associates further opportunities for advanced training. In 2005, Enform trained an estimated 155,000 students, and a number of new courses were introduced and updated. A franchise program was extended and a training council was formed to offer direction and guidance to the oil industry. Enform focuses on sharing information among companies, as well as working to harmonize safety regulations across provincial borders. A task force was recently created by the company with a specific focus on drug and alcohol abuse. Other concerns include driver safety and driver interactions with wildlife. Enform is mainly focused on the traditional oil industry, and has had little entry into the oil sands industry. It was concluded that increased activity in the oil and gas industry will remain Enform's biggest challenge in the next few years. Plans for Enform's increased involvement in the offshore oil and gas industry were also discussed. 4 figs.

  18. Optimal wave focusing for seismic source imaging

    Science.gov (United States)

    Bazargani, Farhad

    In both global and exploration seismology, studying seismic sources provides geophysicists with invaluable insight into the physics of earthquakes and faulting processes. One way to characterize the seismic source is to directly image it. Time-reversal (TR) focusing provides a simple and robust solution to the source imaging problem. However, for recovering a well- resolved image, TR requires a full-aperture receiver array that surrounds the source and adequately samples the wavefield. This requirement often cannot be realized in practice. In most source imaging experiments, the receiver geometry, due to the limited aperture and sparsity of the stations, does not allow adequate sampling of the source wavefield. Incomplete acquisition and imbalanced illumination of the imaging target limit the resolving power of the TR process. The main focus of this thesis is to offer an alternative approach to source imaging with the goal of mitigating the adverse effects of incomplete acquisition on the TR modeling. To this end, I propose a new method, named Backus-Gilbert (BG) source imaging, to optimally focus the wavefield onto the source position using a given receiver geometry. I first introduce BG as a method for focusing waves in acoustic media at a desired location and time. Then, by exploiting the source-receiver reciprocity of the Green function and the linearity of the problem, I show that BG focusing can be adapted and used as a source-imaging tool. Following this, I generalize the BG theory for elastic waves. Applying BG formalism for source imaging requires a model for the wave propagation properties of the earth and an estimate of the source location. Using numerical tests, I next examine the robustness and sensitivity of the proposed method with respect to errors in the earth model, uncertainty in the source location, and noise in data. The BG method can image extended sources as well as point sources. It can also retrieve the source mechanism. These features of

  19. Finding focus: a study of the historical development of focus in English

    NARCIS (Netherlands)

    Komen, E.R.

    2013-01-01

    This study reveals how two important focus articulations change over time in written English. Constituent focus, often accompanied by contrast, makes use of the clause-initial position in the oldest stages of English, but as this position comes to be used for the grammatical subject over time, the

  20. A new electrophoretic focusing principle: focusing of nonamphoteric weak ionogenic analytes using inverse electromigration dispersion profiles.

    Science.gov (United States)

    Gebauer, Petr; Malá, Zdena; Bocek, Petr

    2010-03-01

    This contribution introduces a new separation principle in CE which offers focusing of weak nonamphoteric ionogenic species and their inherent transport to the detector. The prerequisite condition for application of this principle is the existence of an inverse electromigration dispersion profile, i.e. a profile where pH is decreasing toward the anode or cathode for focusing of anionic or cationic weak analytes, respectively. The theory presented defines the principal conditions under which an analyte is focused on a profile of this type. Since electromigration dispersion profiles are migrating ones, the new principle offers inherent transport of focused analytes into the detection cell. The focusing principle described utilizes a mechanism different from both CZE (where separation is based on the difference in mobilities) and IEF (where separation is based on difference in pI), and hence, offers another separation dimension in CE. The new principle and its theory presented here are supplemented by convincing experiments as their proof.

  1. GRI: focusing on the evolving violent universe

    Science.gov (United States)

    Knödlseder, Jürgen; von Ballmoos, Peter; Frontera, Filippo; Bazzano, Angela; Christensen, Finn; Hernanz, Margarida; Wunderer, Cornelia

    2009-03-01

    The gamma-ray imager (GRI) is a novel mission concept that will provide an unprecedented sensitivity leap in the soft gamma-ray domain by using for the first time a focusing lens built of Laue diffracting crystals. The lens will cover an energy band from 200-1,300 keV with an effective area reaching 600 cm2. It will be complemented by a single reflection multilayer coated mirror, extending the GRI energy band into the hard X-ray regime, down to ˜10 keV. The concentrated photons will be collected by a position sensitive pixelised CZT stack detector. We estimate continuum sensitivities of better than 10 - 7 ph cm - 2s - 1keV - 1 for a 100 ks exposure; the narrow line sensitivity will be better than 3 × 10 - 6 ph cm - 2s - 1 for the same integration time. As focusing instrument, GRI will have an angular resolution of better than 30 arcsec within a field of view of roughly 5 arcmin—an unprecedented achievement in the gamma-ray domain. Owing to the large focal length of 100 m of the lens and the mirror, the optics and detector will be placed on two separate spacecrafts flying in formation in a high elliptical orbit. R&D work to enable the lens focusing technology and to develop the required focal plane detector is currently underway, financed by ASI, CNES, ESA, and the Spanish Ministery of Education and Science. The GRI mission has been proposed as class M mission for ESAs Cosmic Vision 2015-2025 program. GRI will allow studies of particle acceleration processes and explosion physics in unprecedented detail, providing essential clues on the innermost nature of the most violent and most energetic processes in the universe.

  2. Tanks focus area. Annual report 1997

    International Nuclear Information System (INIS)

    Frey, J.

    1997-01-01

    The U.S. Department of Energy Office of Environmental Management is tasked with a major remediation project to treat and dispose of radioactive waste in hundreds of underground storage tanks. These tanks contain about 90,000,000 gallons of high-level and transuranic wastes. We have 68 known or assumed leaking tanks, that have allowed waste to migrate into the soil surrounding the tank. In some cases, the tank contents have reacted to form flammable gases, introducing additional safety risks. These tanks must be maintained in the safest possible condition until their eventual remediation to reduce the risk of waste migration and exposure to workers, the public, and the environment. Science and technology development for safer, more efficient, and cost-effective waste treatment methods will speed up progress toward the final remediation of these tanks. The DOE Office of Environmental Management established the Tanks Focus Area to serve as the DOE-EM's technology development program for radioactive waste tank remediation in partnership with the Offices of Waste Management and Environmental Restoration. The Tanks Focus Area is responsible for leading, coordinating, and facilitating science and technology development to support remediation at DOE's four major tank sites: the Hanford Site in Washington State, Idaho National Engineering and Environmental Laboratory in Idaho, Oak Ridge Reservation in Tennessee, and the Savannah River Site in South Carolina. The technical scope covers the major functions that comprise a complete tank remediation system: waste retrieval, waste pretreatment, waste immobilization, tank closure, and characterization of both the waste and tank. Safety is integrated across all the functions and is a key component of the Tanks Focus Area program

  3. The combination of electrospray and flow focusing

    Science.gov (United States)

    Gañán-Calvo, Alfonso M.; López-Herrera, José M.; Riesco-Chueca, Pascual

    2006-11-01

    An ultra-fine liquid atomization procedure combining the advantages of electrospray and flow focusing is presented. Both techniques are known to produce strikingly small and steady liquid micro-jets issuing from menisci held by capillary forces. Such menisci take the form of a cusp-like drop attached to the feeding tube (flow focusing: FF) or a Taylor cone (electrospray: ES). The issuing micro-jets are forced or ‘sucked’ from the parent meniscus either by pressure or electrohydrodynamic forces. Subsequent capillary breakup of the jet leads to fine sprays of remarkable quality. Here we describe the joint effect of pressurization and electrification in a flow focusing device, and the subsequent coupling of both ES and FF phenomena. For any given liquid and flow rate, the combined procedure gives rise to significantly smaller droplet sizes than observed in any of the source techniques. The co-flowing gas stream removes space charges; in addition, the perforated plate facing the feed tube provides an electric barrier, shielding the jet-meniscus or ‘production’ area from the spray or ‘product’ area. As a result, space charges and electrified droplets are removed from the production area, thus avoiding the ambient electric saturation which becomes a limiting factor in ES-spraying: a significantly enhanced spraying stability ensues, with a much wider operation range than FF or ES. Other unexpected outcomes from the combination are also shown. A theoretical model is developed to predict the emitted droplet size: a first integral of the momentum equation yielding a generalized Bernoulli equation, and an explicit approximation for the jet diameter and droplet size, accurate within a broad parametrical band.

  4. Electron density measurements on the plasma focus

    International Nuclear Information System (INIS)

    Rueckle, B.

    1976-01-01

    The paper presents a determination of the maximum electron density in a plasma focus, produced with the NESSI experimental setup, by the method of laser beam deflection. For each discharge a time-resolved measurement was performed at four different places. Neutron efficiency as well as the time of the initial X-ray emission was registrated. The principle and the economic aspects of the beam deflection method are presented in detail. The experimental findings and the resulting knowledge of the neutron efficiency are discussed. (GG) [de

  5. Focusing experiments with light ion diodes

    International Nuclear Information System (INIS)

    Johnson, D.L.

    1978-01-01

    A review of recent experimental and theoretical work at Sandia Laboratories on magnetically insulated single stage ion diodes for inertial confinement fusion experiments is presented. The production, focusing, and numerical simulation of a 0.5 TW annular proton beam using the Proto I dual transmission line generator is described. The modular magnetically insulated ion diode for the Hydra generator is also described along with recent experimental results. A brief description of how an array of modular diodes similar to the Hydra magnetically insulated diode could be used on the EBFA I generator for breakeven fusion experiments is presented

  6. Focusing over Optical Fiber Using Time Reversal

    DEFF Research Database (Denmark)

    Piels, Molly; Porto da Silva, Edson; Estaran Tolosa, Jose Manuel

    2015-01-01

    A time-reversal array in multimode fiber is proposed for lossless remotely controlled switching using passive optical splitters. The signal to be transmitted is digitally pre-distorted so that it is routed through the physical layer in order to arrive at only one receiver in an array. System...... performance in the presence of additive white gaussian noise, modal group delay, and timing error is investigated numerically for single-mode and 10-mode fiber. Focusing using a two-transmitter array and 44 km of single- mode fiber is demonstrated experimentally for 3 GBd QPSK signals with a bit error rate...

  7. Focus point from direct gauge mediation

    Energy Technology Data Exchange (ETDEWEB)

    Zheng, Sibo [Chongqing University, Department of Physics, Chongqing (China)

    2015-01-01

    This paper is devoted to the reconciliation of the tension between the theoretic expectation from naturalness and the present LHC limits on the superpartner mass bounds. We argue that in supersymmetry models of direct gauge mediation the focusing phenomenon appears, which dramatically reduces the fine tuning associated to the 126 GeV Higgs boson. This type of model is highly predictive as regards the mass spectrum, with a multi-TeV third generation, the A{sub t} term of order 1 TeV, gluino mass above LHC mass bound, and the light neutralinos and charginos below 1 TeV. (orig.)

  8. Triplet Focusing for Recirculating Linear Muon Accelerators

    CERN Document Server

    Keil, Eberhard

    2001-01-01

    Focusing by symmetrical triplets is studied for the linear accelerator lattices in recirculating muon accelerators with several passes where the ratio of final to initial muon energy is about four. Triplet and FODO lattices are compared. At similar acceptance, triplet lattices have straight sections for the RF cavities that are about twice as long as in FODO lat-tices. For the same energy gain, the total lengths of the linear accelerators with triplet lattices are about the same as of those with FODO lattices.

  9. Orbiter radiator panel solar focusing test

    Science.gov (United States)

    Howell, H. R.; Rankin, J. G.

    1983-01-01

    Test data are presented which define the area around the Orbiter radiator panels for which the solar reflections are concentrated to one-sun or more. The concave shape of the panels and their specular silver/Teflon coating causes focusing of the reflected solar energy which could have adverse heating effects on equipment or astronaut extravehicular activity (EVA) in the vicinity of the radiator panels. A room ambient test method was utilized with a one-tenth scale model of the radiator panels.

  10. Mixed Waste Focus Area program management plan

    International Nuclear Information System (INIS)

    Beitel, G.A.

    1996-10-01

    This plan describes the program management principles and functions to be implemented in the Mixed Waste Focus Area (MWFA). The mission of the MWFA is to provide acceptable technologies that enable implementation of mixed waste treatment systems developed in partnership with end-users, stakeholders, tribal governments and regulators. The MWFA will develop, demonstrate and deliver implementable technologies for treatment of mixed waste within the DOE Complex. Treatment refers to all post waste-generation activities including sampling and analysis, characterization, storage, processing, packaging, transportation and disposal

  11. Virtual Focus Groups: New Frontiers in Research

    Directory of Open Access Journals (Sweden)

    Lyn Turney

    2005-06-01

    Full Text Available New information and communication technologies in the form of learning management systems provide unique and inventive opportunities for qualitative researchers. Their intrinsic ability to record discursive data in text format accurately and to provide safe, secure, and anonymous environments for participants makes them amenable for use as advanced research tools. In this article, the authors report on a collaborative project that tested the potential of online discussion boards for use in virtual focus groups. What the researchers found was that not only was the method theoretically sound, it actually enhanced their ability to connect with difficult-to-access populations that were disparately spread.

  12. Centroid motion in periodically focused beams

    International Nuclear Information System (INIS)

    Moraes, J.S.; Pakter, R.; Rizzato, F.B.

    2005-01-01

    The role of the centroid dynamics in the transport of periodically focused particle beams is investigated. A Kapchinskij-Vladimirskij equilibrium distribution for an off-axis beam is derived. It is shown that centroid and envelope dynamics are uncoupled and that unstable regions for the centroid dynamics overlap with previously stable regions for the envelope dynamics alone. Multiparticle simulations validate the findings. The effects of a conducting pipe encapsulating the beam are also investigated. It is shown that the charge induced at the pipe may generate chaotic orbits which can be detrimental to the adequate functioning of the transport mechanism

  13. BIOENERGIA - Focus on wood in bioenergy research

    Energy Technology Data Exchange (ETDEWEB)

    Asplund, D. [Jyvaeskylae Science Park, Jyvaeskylae (Finland)

    1996-12-31

    The most important area of research on wood fuel production is the development of various methods, machines and systems connected to this area, in order to produce economically competitive fuels. The integrated harvesting methods, which supply both raw material to wood products industry and wood fuel for energy production, have been chosen the main research area because they seem to be most promising. The growing amount of small-sized trees ant the need of their first thinnings have created a demand for new harvesting methods. At the moment the economical aspects restrict the harvesting of the first thinning trees either for industrial use or energy production. Research on peat production focuses on the complete use of a bog and on the development of peat production methods and machines. Development work in this area aims at decreasing production costs and also at reducing the drainage water and other elements in environmental load around the peat production sites. The use of bioenergy research will be focused on the small-scale (<20 MW{sub th},) applications. In the long term, the increase of bioenergy in heating of small houses and farms and buildings, as well as in the production of heat and power has been estimated. Research into the conversion of biomass is concentrated on the production of biomass-based liquid fuels

  14. Resonant Varifocal Micromirror with Piezoresistive Focus Sensor

    Directory of Open Access Journals (Sweden)

    Kenta Nakazawa

    2016-03-01

    Full Text Available This paper reports a microelectromechanical systems (MEMS resonant varifocal mirror integrated with piezoresistive focus sensor. The varifocal mirror is driven electrostatically at a resonant frequency of a mirror plate to obtain the wide scanning range of a focal length. A piezoresistor is used to monitor the focal length of the varifocal mirror. The device is made of a silicon-on-insulator (SOI wafer and a glass wafer. A mirror plate and a counter electrode are fabricated by a top silicon layer of the SOI wafer and on the glass wafer, respectively. The piezoresistor is fabricated by ion implantation on a supporting beam of the mirror plate. The stress variation of the beam, which is detected by the piezoresistor, correspond the focal length of the varifocal mirror. The focus length varies from −41 to 35 mm at the resonant frequency of 9.5 kHz. The focal length of the varifocal mirror is monitored by the piezoresistor in real time.

  15. Focusing on the essentials: learning for performance.

    Science.gov (United States)

    Murphy, Catherine J

    2008-12-10

    As The World health report 2006 emphasized, there is increasing consensus that training programmes should focus on "know-how" instead of "know-all." Health workers need to know how to do the job they will be expected to do. IntraHealth International's Learning for performance: a guide and toolkit for health worker training and education programs offers a step-by-step, customizable approach designed to develop the right skills linked to job responsibilities. Using Learning for performance (LFP) yields more efficient training that focuses on what is essential for health workers to do their jobs and on effective learning methods, while addressing the factors that ensure application of new skills on the job. This brief communication describes the Learning for performance approach and initial findings from its application for pre-service education and in-service training in three countries: India, Mali and Bangladesh. Based on IntraHealth's experiences, the author provides thoughts on how LFP's performance-based learning approach can be a useful tool in training scale-up to strengthen human resources for health.

  16. Focused sound: oncological therapy for transformed tissue

    International Nuclear Information System (INIS)

    Mares, C. E.; Cordova F, T.; Hernandez, A.

    2017-10-01

    The restlessness of the human being involves observing and being critical through their senses, in particular a disturbance in the environment cause vibrations that can be registered by the sense of hearing through the eardrum, if what it produces is in the frequency of the audible sound. The distinction of the sound of the other forms of energy transfer is that the waves of the same quickly involve the progressive return of displacements or vibrations of the molecules in the medium that propagates. In this work a sweep of frequencies was made from infra sound to ultrasound in plants of different types with different thicknesses and two people in order to find the resonance of each of them and compare it with the resonances registered in text, which allowed evaluate the secondary effect of sound focused on the tissue of the leaves and in particular of people. We consider that there is potential for this focused sound modality if it is at the resonance frequency of the transformed tissue as a means of oncological therapy without affecting the neighboring cells. (Author)

  17. Focusing on the essentials: learning for performance

    Directory of Open Access Journals (Sweden)

    Murphy Catherine J

    2008-12-01

    Full Text Available Abstract As The World health report 2006 emphasized, there is increasing consensus that training programmes should focus on "know-how" instead of "know-all." Health workers need to know how to do the job they will be expected to do. IntraHealth International's Learning for performance: a guide and toolkit for health worker training and education programs offers a step-by-step, customizable approach designed to develop the right skills linked to job responsibilities. Using Learning for performance (LFP yields more efficient training that focuses on what is essential for health workers to do their jobs and on effective learning methods, while addressing the factors that ensure application of new skills on the job. This brief communication describes the Learning for performance approach and initial findings from its application for pre-service education and in-service training in three countries: India, Mali and Bangladesh. Based on IntraHealth's experiences, the author provides thoughts on how LFP's performance-based learning approach can be a useful tool in training scale-up to strengthen human resources for health.

  18. Plant status control - with an operational focus

    International Nuclear Information System (INIS)

    Lane, L.A.

    2000-01-01

    In the Nuclear industry, we have done a very good job of designing, developing, constructing, and improving our nuclear facilities. We have, however, often been inconsistent in documenting the details of our facilities, clearly addressing the rules around facility operation, and controlling and tracking the temporary, or permanent changes to our facilities. The reality is, that once we build a facility, we then must operate the facility, for it to be viable. Further we must operate it safely and efficiently for the facility to produce its product, and be acceptable to the public. Unfortunately, when we design and build these large, complicated facilities, we cannot project all the nuances of facility operation, although we can recognize this potential gap, and prepare for it. In order to allow for the complexities of the real world, we must provide the individuals who are tasked with operating our nuclear facilities, with the tools and processes to deal with 'all the nuances' of facility operation. This discussion will focus on the concepts behind a key process for ensuring that we meet our design and operating needs for our facilities, as well as recognizing and dealing with the potential gaps. The key process is 'Plant Status Control', and the discussion will have a primary focus on the needs of the end users, that being the individuals that have the immediate and current accountability for control and safety of the facility, the equipment, the staff, and ultimately the public, that being our Operations staff, and the Shift Manager. (author)

  19. Focused ion beam milling of carbon fibres

    International Nuclear Information System (INIS)

    Huson, Mickey G.; Church, Jeffrey S.; Hillbrick, Linda K.; Woodhead, Andrea L.; Sridhar, Manoj; Van De Meene, Allison M.L.

    2015-01-01

    A focused ion beam has been used to mill both individual carbon fibres as well as fibres in an epoxy composite, with a view to preparing flat surfaces for nano-indentation. The milled surfaces have been assessed for damage using scanning probe microscopy nano-indentation and Raman micro-probe analysis, revealing that FIB milling damages the carbon fibre surface and covers surrounding areas with debris of disordered carbon. The debris is detected as far as 100 μm from the milling site. The energy of milling as well as the orientation of the beam was varied and shown to have an effect when assessed by Raman spectroscopy. - Highlights: • Focused ion beam (FIB) milling was used to mill flat surfaces on carbon fibres. • Raman spectroscopy showed amorphous carbon was generated during FIB milling. • The amorphous debris is detected as far as 100 μm from the milling site. • This surface degradation was confirmed by nano-indentation experiments.

  20. SIAM Workshop: Focus on Diversity 2001

    Energy Technology Data Exchange (ETDEWEB)

    None

    2001-01-01

    The Society for Industrial and Applied Mathematics (SIAM) held a workshop focused on underrepresented minorities--graduate and undergraduate students, postdocs, and recent Ph.D's--in the mathematical and computational sciences on July 11, 2001, as part of the SIAM Annual Meeting in San Diego, California. The workshop was intended to accomplish several goals: (1) to a provide workshop focused on careers for and retention of minority students in the mathematical and computational sciences; (2) to bring together a mixture of people from different levels of professional experience, ranging from undergraduate students to senior scientists in an informal setting in order to share career experiences and options; (3) to provide an opportunity for minority graduate students, postdocs, and recent Ph.D's to present their research at an international meeting; (4) to expose undergraduate students to the many professional opportunities resulting from graduate degrees in science and mathematics; and (5) to encourage undergraduate and graduate students to speak frankly with each other about personal issues and experiences associated with pursuing a scientific career.

  1. Focusing on reproductive health for adolescents.

    Science.gov (United States)

    1995-06-01

    JOICFP is producing a still photo video consisting of three segments from photos shot in Bangladesh (April 22 - May 2), Thailand (May 2-15), and Mexico (June 29 - July 7) in 1995. The first segment highlights the daily life of a husband, aged 20, and his wife, Moni, aged 14. Moni married at age 13, before the onset of menstruation, and now serves and feeds her husband's large extended family. The Family Planning Association of Bangladesh (FPAB), the local implementing agent of the Sustainable Community-based Family Planning/Maternal and Child Health (FP/MCH) Project with Special Focus on Women, which is supported by the United Nations Population Fund (UNFPA) and executed by JOICFP, introduced Moni to the concept of reproductive health and encouraged her to join other women in activities designed to improve their health and raise their economic status. The second segment depicts the life of a former commercial sex worker who is undergoing occupational skill development training promoted by the Population and Community Development Association. The girl is now a leader of teenagers in her village; she works to change attitudes that sent her to work as a prostitute with an estimated 150,000 other poor rural teenage women. The third segment focuses on teen pregnancy and the efforts of the Mexican Foundation for Family Planning (MEXFAM) in the areas of health care and education for adolescents.

  2. Focus of attention and automaticity in handwriting.

    Science.gov (United States)

    MacMahon, Clare; Charness, Neil

    2014-04-01

    This study investigated the nature of automaticity in everyday tasks by testing handwriting performance under single and dual-task conditions. Item familiarity and hand dominance were also manipulated to understand both cognitive and motor components of the task. In line with previous literature, performance was superior in an extraneous focus of attention condition compared to two different skill focus conditions. This effect was found only when writing with the dominant hand. In addition, performance was superior for high familiarity compared to low familiarity items. These findings indicate that motor and cognitive familiarity are related to the degree of automaticity of motor skills and can be manipulated to produce different performance outcomes. The findings also imply that the progression of skill acquisition from novel to novice to expert levels can be traced using different dual-task conditions. The separation of motor and cognitive familiarity is a new approach in the handwriting domain, and provides insight into the nature of attentional demands during performance. Copyright © 2013 Elsevier B.V. All rights reserved.

  3. Drawing road networks with focus regions.

    Science.gov (United States)

    Haunert, Jan-Henrik; Sering, Leon

    2011-12-01

    Mobile users of maps typically need detailed information about their surroundings plus some context information about remote places. In order to avoid that the map partly gets too dense, cartographers have designed mapping functions that enlarge a user-defined focus region--such functions are sometimes called fish-eye projections. The extra map space occupied by the enlarged focus region is compensated by distorting other parts of the map. We argue that, in a map showing a network of roads relevant to the user, distortion should preferably take place in those areas where the network is sparse. Therefore, we do not apply a predefined mapping function. Instead, we consider the road network as a graph whose edges are the road segments. We compute a new spatial mapping with a graph-based optimization approach, minimizing the square sum of distortions at edges. Our optimization method is based on a convex quadratic program (CQP); CQPs can be solved in polynomial time. Important requirements on the output map are expressed as linear inequalities. In particular, we show how to forbid edge crossings. We have implemented our method in a prototype tool. For instances of different sizes, our method generated output maps that were far less distorted than those generated with a predefined fish-eye projection. Future work is needed to automate the selection of roads relevant to the user. Furthermore, we aim at fast heuristics for application in real-time systems. © 2011 IEEE

  4. An ultra miniature pinch-focus discharge

    International Nuclear Information System (INIS)

    Soto, L.; Pavez, C.; Moreno, J.; Pavez, C.; Barbaglia, M.; Clausse, A.

    2004-01-01

    As a way to investigate the minimum energy to produce a pinch plasma focus discharge, an ultra miniature device has been designed and constructed (nano focus NF: 5 nF, 5-10 kV, 5-10 kA, 60-250 mJ, 16 ns time to peak current). Sub-millimetric anode radius covered by a coaxial insulator were used for experiments in hydrogen. Evidence of pinch was observed in electrical signals in discharges operating at 60 mJ. A single-frame image converter camera (4 ns exposure) was used to obtain plasma images in the visible range. The dynamics observed from the photographs is consistent with: a) formation of a plasma sheath close to the insulator surface, b) fast axial motion of the plasma sheath, c) radial compression over the anode, and d) finally the plasma is detached from the anode in the axial direction. The total time since stage a) to d) was observed to be about 30 ns. X ray and neutron emission is being studied. Neutron yield of the order of 10 3 neutrons per shot is expected for discharges operating in deuterium at 10 kA. (authors)

  5. Focused Wind Mass Accretion in Mira AB

    Science.gov (United States)

    Karovska, Margarita; de Val-Borro, M.; Hack, W.; Raymond, J.; Sasselov, D.; Lee, N. P.

    2011-05-01

    At a distance of about only 100pc, Mira AB is the nearest symbiotic system containing an Asymptotic Giant Branch (AGB) star (Mira A), and a compact accreting companion (Mira B) at about 0.5" from Mira A. Symbiotic systems are interacting binaries with a key evolutionary importance as potential progenitors of a fraction of asymmetric Planetary Nebulae, and SN type Ia, cosmological distance indicators. The region of interaction has been studied using high-angular resolution, multiwavelength observations ranging from radio to X-ray wavelengths. Our results, including high-angular resolution Chandra imaging, show a "bridge" between Mira A and Mira B, indicating gravitational focusing of the Mira A wind, whereby components exchange matter directly in addition to the wind accretion. We carried out a study using 2-D hydrodynamical models of focused wind mass accretion to determine the region of wind acceleration and the characteristics of the accretion in Mira AB. We highlight some of our results and discuss the impact on our understanding of accretion processes in symbiotic systems and other detached and semidetached interacting systems.

  6. Focusing an antimatter beam with matter

    CERN Document Server

    CERN. Geneva

    2000-01-01

    An experiment at the Stanford Linear Accelerator Center has recently focused positron beams by means of a plasma lens. This is the first time this process has been observed. The process started with a positron beam from the SLAC PEP-II positron source. This was sent through a damping ring and then accelerated to 28.5 GeV in the SLAC linac with a bunch intensity of 1-2*10/sup 10/. The beam was delivered to the Final Focus Test Beam Facility (FFTB) at a rate of 1 or 10 Hz. At the focal point of the FFTB transport, a special plasma chamber contains a 3 mm diameter pulsed gas nozzle through which either hydrogen or nitrogen gas is "puffed" into the ultrahigh vacuum system at plenum gas pressures up to 75 atm with a discharge time of 800 mu s. The gas is pumped off by a Roots-type pump. On either side of the central chamber are differential pumping sections semi- isolated from each other by thin titanium windows with small (2-5 mm diameter) apertures for the positron beams to pass through. These sections are evacu...

  7. Targeted therapy using nanotechnology: focus on cancer.

    Science.gov (United States)

    Sanna, Vanna; Pala, Nicolino; Sechi, Mario

    2014-01-01

    Recent advances in nanotechnology and biotechnology have contributed to the development of engineered nanoscale materials as innovative prototypes to be used for biomedical applications and optimized therapy. Due to their unique features, including a large surface area, structural properties, and a long circulation time in blood compared with small molecules, a plethora of nanomaterials has been developed, with the potential to revolutionize the diagnosis and treatment of several diseases, in particular by improving the sensitivity and recognition ability of imaging contrast agents and by selectively directing bioactive agents to biological targets. Focusing on cancer, promising nanoprototypes have been designed to overcome the lack of specificity of conventional chemotherapeutic agents, as well as for early detection of precancerous and malignant lesions. However, several obstacles, including difficulty in achieving the optimal combination of physicochemical parameters for tumor targeting, evading particle clearance mechanisms, and controlling drug release, prevent the translation of nanomedicines into therapy. In spite of this, recent efforts have been focused on developing functionalized nanoparticles for delivery of therapeutic agents to specific molecular targets overexpressed on different cancer cells. In particular, the combination of targeted and controlled-release polymer nanotechnologies has resulted in a new programmable nanotherapeutic formulation of docetaxel, namely BIND-014, which recently entered Phase II clinical testing for patients with solid tumors. BIND-014 has been developed to overcome the limitations facing delivery of nanoparticles to many neoplasms, and represents a validated example of targeted nanosystems with the optimal biophysicochemical properties needed for successful tumor eradication.

  8. Art exhibit focuses on African astronomy

    Science.gov (United States)

    Showstack, Randy

    2012-07-01

    Connections between Africans and astronomy are the focus of a new exhibition in the National Museum of African Art in Washington, D. C. "African Cosmos: Stellar Arts," which includes artwork, cultural items, and scientific displays from ancient to contemporary times, is the first major exhibit "that brings together arts and science focused on Africa's contribution to keen observations of the heavens over time," curator Christine Mullen Kreamer said at a 20 June news briefing. Among the exhibit's nearly 100 objects are an ancient Egyptian mummy board that includes a representation of the sky goddess Nut, sculptures by the Dogon people of Mali depicting figures in relation to the cosmos, a video that uses data from two square degrees of the Hubble Space Telescope Cosmic Evolution Survey, and a nearly floor-to-ceiling "Rainbow Serpent" constructed of plastic containers by Benin artist Hazoume. An untitled acrylic painting (Figure 1) by South African Gavin Jantjes evokes a myth of the Khoi San people of southern Africa, as it portrays a girl throwing evening fire embers into the night sky, where they remained as the Milky Way.

  9. Intensity dependence of focused ultrasound lesion position

    Science.gov (United States)

    Meaney, Paul M.; Cahill, Mark D.; ter Haar, Gail R.

    1998-04-01

    Knowledge of the spatial distribution of intensity loss from an ultrasonic beam is critical to predicting lesion formation in focused ultrasound surgery. To date most models have used linear propagation models to predict the intensity profiles needed to compute the temporally varying temperature distributions. These can be used to compute thermal dose contours that can in turn be used to predict the extent of thermal damage. However, these simulations fail to adequately describe the abnormal lesion formation behavior observed for in vitro experiments in cases where the transducer drive levels are varied over a wide range. For these experiments, the extent of thermal damage has been observed to move significantly closer to the transducer with increasing transducer drive levels than would be predicted using linear propagation models. The simulations described herein, utilize the KZK (Khokhlov-Zabolotskaya-Kuznetsov) nonlinear propagation model with the parabolic approximation for highly focused ultrasound waves, to demonstrate that the positions of the peak intensity and the lesion do indeed move closer to the transducer. This illustrates that for accurate modeling of heating during FUS, nonlinear effects must be considered.

  10. Optical fiber plasmonic lens for near-field focusing fabricated through focused ion beam

    Science.gov (United States)

    Sloyan, Karen; Melkonyan, Henrik; Moreira, Paulo; Dahlem, Marcus S.

    2017-02-01

    We report on numerical simulations and fabrication of an optical fiber plasmonic lens for near-field focusing applications. The plasmonic lens consists of an Archimedean spiral structure etched through a 100 nm-thick Au layer on the tip of a single-mode SM600 optical fiber operating at a wavelength of 632:8 nm. Three-dimensional finite-difference time-domain computations show that the relative electric field intensity of the focused spot increases 2:1 times when the number of turns increases from 2 to 12. Furthermore, a reduction of the intensity is observed when the initial inner radius is increased. The optimized plasmonic lens focuses light into a spot with a full-width at half-maximum of 182 nm, beyond the diffraction limit. The lens was fabricated by focused ion beam milling, with a 200nm slit width.

  11. PREFACE: Focus section on Hadronic Physics

    Science.gov (United States)

    Roberts, Craig; Swanson, Eric

    2007-07-01

    Hadronic physics is the study of strongly interacting matter and its underlying theory, Quantum Chromodynamics (QCD). The field had its beginnings after World War Two, when hadrons were discovered in ever increasing numbers. Today, it encompasses topics like the quark-gluon structure of hadrons at varying scales, the quark-gluon plasma and hadronic matter at extreme temperature and density; it also underpins nuclear physics and has significant impact on particle physics, astrophysics, and cosmology. Among the goals of hadronic physics are to determine the parameters of QCD, understand the origin and characteristics of confinement, understand the dynamics and consequences of dynamical chiral symmetry breaking, explore the role of quarks and gluons in nuclei and in matter under extreme conditions and understand the quark and gluon structure of hadrons. In general, the process is one of discerning the relevant degrees of freedom and relating these to the fundamental fields of QCD. The emphasis is on understanding QCD, rather than testing it. The papers gathered in this special focus section of Journal of Physics G: Nuclear and Particle Physics attempt to cover this broad range of subjects. Alkofer and Greensite examine the issue of quark and gluon confinement with the focus on models of the QCD vacuum, lattice gauge theory investigations, and the relationship to the AdS/CFT correspondence postulate. Arrington et al. review nucleon form factors and their role in determining quark orbital momentum, the strangeness content of the nucleon, meson cloud effects, and the transition from nonperturbative to perturbative QCD dynamics. The physics associated with hadronic matter at high temperature and density and at low Bjorken-x at the Relativistic Heavy Ion Collider (RHIC), the SPS at CERN, and at the future LHC is summarized by d'Enterria. The article of Lee and Smith examines experiment and theory associated with electromagnetic meson production from nucleons and

  12. Focus: Global histories of science. Introduction.

    Science.gov (United States)

    Sivasundaram, Sujit

    2010-03-01

    An interest in global histories of science is not new. Yet the project envisioned by this Focus section is different from that pursued by natural historians and natural philosophers in the early modern age. Instead of tracing universal patterns, there is value in attending to the connections and disconnections of science on the global stage. Instead of assuming the precision of science's boundaries, historians might consider the categories of "science" and "indigenous knowledge" to have emerged from globalization. New global histories of science will be characterized by critical reflection on the limits of generalization, as well as a creative adoption of new sources, methods, and chronologies, in an attempt to decenter the European history of science. Such a project holds the promise of opening up new conversations between historians, anthropologists, philosophers, and sociologists of science. It is of critical importance if the discipline is not to fragment into regional and national subfields or become dominated by structural frameworks such as imperialism.

  13. Radioactive tank waste remediation focus area

    International Nuclear Information System (INIS)

    1996-08-01

    EM's Office of Science and Technology has established the Tank Focus Area (TFA) to manage and carry out an integrated national program of technology development for tank waste remediation. The TFA is responsible for the development, testing, evaluation, and deployment of remediation technologies within a system architecture to characterize, retrieve, treat, concentrate, and dispose of radioactive waste stored in the underground stabilize and close the tanks. The goal is to provide safe and cost-effective solutions that are acceptable to both the public and regulators. Within the DOE complex, 335 underground storage tanks have been used to process and store radioactive and chemical mixed waste generated from weapon materials production and manufacturing. Collectively, thes tanks hold over 90 million gallons of high-level and low-level radioactive liquid waste in sludge, saltcake, and as supernate and vapor. Very little has been treated and/or disposed or in final form

  14. Radioactive tank waste remediation focus area

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-08-01

    EM`s Office of Science and Technology has established the Tank Focus Area (TFA) to manage and carry out an integrated national program of technology development for tank waste remediation. The TFA is responsible for the development, testing, evaluation, and deployment of remediation technologies within a system architecture to characterize, retrieve, treat, concentrate, and dispose of radioactive waste stored in the underground stabilize and close the tanks. The goal is to provide safe and cost-effective solutions that are acceptable to both the public and regulators. Within the DOE complex, 335 underground storage tanks have been used to process and store radioactive and chemical mixed waste generated from weapon materials production and manufacturing. Collectively, thes tanks hold over 90 million gallons of high-level and low-level radioactive liquid waste in sludge, saltcake, and as supernate and vapor. Very little has been treated and/or disposed or in final form.

  15. Subsurface Contaminants Focus Area annual report 1997

    International Nuclear Information System (INIS)

    1997-01-01

    In support of its vision for technological excellence, the Subsurface Contaminants Focus Area (SCFA) has identified three strategic goals. The three goals of the SCFA are: Contain and/or stabilize contamination sources that pose an imminent threat to surface and ground waters; Delineate DNAPL contamination in the subsurface and remediate DNAPL-contaminated soils and ground water; and Remove a full range of metal and radionuclide contamination in soils and ground water. To meet the challenges of remediating subsurface contaminants in soils and ground water, SCFA funded more than 40 technologies in fiscal year 1997. These technologies are grouped according to the following product lines: Dense Nonaqueous-Phase Liquids; Metals and Radionuclides; Source Term Containment; and Source Term Remediation. This report briefly describes the SCFA 1997 technologies and showcases a few key technologies in each product line

  16. The heating of plasma focus electrodes

    International Nuclear Information System (INIS)

    Angeli, E; Frignani, M; Mannucci, S; Rocchi, F; Sumini, M; Tartari, A

    2006-01-01

    Plasma focus (PF) technology development today is strictly related to the possibility of a high frequency repetitive working regime. One of the more relevant obstacles to this goal is the heating of structural components due to direct interaction with plasma. In this paper, temperature decay measurements of the inner electrode of a 7 kJ Mather type PF are presented. Data from several series of shots at different bank energies are analysed and compared with theoretical and numerical models. Two possible scale laws are derived from the experimental data to correlate thermal deposition with bank energy. It is found that a fraction of about 10% of total energy is released to the inner electrode. Finally, after some considerations about the cooling and heating mechanisms, an analysis on maximum temperature sustained by materials is presented

  17. Current scaling of plasma focus devices

    International Nuclear Information System (INIS)

    Schiuma, C.; Herold, H.; Kaeppeler, H.J.; Shakhatre, M.; Auluck, S.K.H.

    1990-03-01

    In continuation of the work by G. Decker et al. on current and neutron yield scaling of plasma focus devices an analytical solution for the circuit equation (with resistance R = 0) in the compression phase was derived. Together with the solution for the rundown phase from G. Decker et al, which was extended for finite resistance (R ≠ 0), there follows an analytical scaling theory for maximum and pinch currents. At the same time there exists the possibility to discuss the influence of finite resistance on current variation and scaling parameters. The model solutions were checked out by numerical integrations of the current equation. While at the beginning of the rundown phase the ohmic resistance cannot be neglected (the magnitude R/L plays an important role), its influence at the end of the rundown phase and in the compression phase is negligible. The theoretically determined values are compared with the results of numerous probe measurements. (orig.)

  18. Norwegian focus on new energy technology

    International Nuclear Information System (INIS)

    Bull-Hansen, Eivind

    2001-01-01

    Norsk Hydro Technology Ventures, a venture capital fund recently set up by Norsk Hydro, will raise equity capital to companies that are developing promising new projects on new energy technology or to investment funds promoting such projects. Norsk Hydro will withdraw from the investments when the projects have reached commercialization or are listed on the stock exchange. There is a well-developed market for venture capital in the energy sector and a strong international competition for investments in good projects. The sharp environmental focus on fossil fuels and climate gases has boosted the research on new energy technologies. Another and more important factor is the fact that modern society with its heavy dependence on the computer is vulnerable to power failure

  19. Ion acceleration in the plasma focus

    International Nuclear Information System (INIS)

    Deutsch, R.

    1982-09-01

    Experimental informations are used to estimate the time dependence of the current density in the plasma focus and the electromagnetic field is determined from the Maxwell equations. The acceleration of the ions in these fields is studied. A detailed analysis of the acceleration in the compression phase, in the expansion phase and during the evolution of the m=O instability is made. It is shown, that the appearance of fast selffocused quasineutral electron beams, as a result of the betatron acceleration, has a decisive importance in the ion acceleration during the m=O constriction. Models for electromagnetic ion acceleration are described for each phase. A concordance with many experimental results can be observed. (orig.)

  20. The IAEA Focuses on Global Nutritional Needs

    International Nuclear Information System (INIS)

    Amano, Yukiya

    2014-01-01

    For over fifty years, the IAEA has been helping its Member States to harness peaceful nuclear science and technology to bring demonstrable benefits to their people. Nutrition is one area in which the IAEA’s partnership with Member States has steadily deepened. This issue of the IAEA Bulletin focuses on the IAEA’s work in nutrition. Topics include our initiatives to measure human milk intake in breastfed infants, lean body mass (muscle mass) in lactating mothers, and the bioavailability of iron in infants and young children. We also look at the paradox of the simultaneous occurrence of both undernutrition and overnutrition that is often found within communities, and even households, across the globe. The IAEA is committed to doing everything it can to make peaceful nuclear technology available to help give all the children of the world a brighter future

  1. Focus on energy conservation: a project list

    Energy Technology Data Exchange (ETDEWEB)

    1978-04-01

    The Urban Land Institute (ULI) has prepared the following list of outstanding energy conserving projects for the US Department of Energy. As requested by the Department, the list includes descriptions of land developments and individual buildings suggested by members of ULI and by other sources. The projects have been selected to exemplify the major energy saving techniques in use today, with emphasis on those strategies most significant for people engaged in the business of land development. To make the list a useful reference for developers and public officials, ULI has attempted to cover energy conservation in the broadest sense from overall site planning to the functioning of individual building components. Focusing too closely on the myriad types of hardware available has been avoided and examples of the basic considerations important to energy-conscious planning and design are provided. Details on some heating, ventilation and air conditioning systems are provided in order to acquaint readers with major innovations in the field.

  2. Deterministic dynamics of plasma focus discharges

    International Nuclear Information System (INIS)

    Gratton, J.; Alabraba, M.A.; Warmate, A.G.; Giudice, G.

    1992-04-01

    The performance (neutron yield, X-ray production, etc.) of plasma focus discharges fluctuates strongly in series performed with fixed experimental conditions. Previous work suggests that these fluctuations are due to a deterministic ''internal'' dynamics involving degrees of freedom not controlled by the operator, possibly related to adsorption and desorption of impurities from the electrodes. According to these dynamics the yield of a discharge depends on the outcome of the previous ones. We study 8 series of discharges in three different facilities, with various electrode materials and operating conditions. More evidence of a deterministic internal dynamics is found. The fluctuation pattern depends on the electrode materials and other characteristics of the experiment. A heuristic mathematical model that describes adsorption and desorption of impurities from the electrodes and their consequences on the yield is presented. The model predicts steady yield or periodic and chaotic fluctuations, depending on parameters related to the experimental conditions. (author). 27 refs, 7 figs, 4 tabs

  3. The IAEA Focuses On Global Nutritional Needs

    International Nuclear Information System (INIS)

    Amano, Yukiya

    2014-01-01

    For over fifty years, the IAEA has been helping its Member States to harness peaceful nuclear science and technology to bring demonstrable benefits to their people. Nutrition is one area in which the IAEA’s partnership with Member States has steadily deepened. This issue of the IAEA Bulletin focuses on the IAEA’s work in nutrition. Topics include our initiatives to measure human milk intake in breastfed infants, lean body mass (muscle mass) in lactating mothers, and the bioavailability of iron in infants and young children. We also look at the paradox of the simultaneous occurrence of both undernutrition and overnutrition that is often found within communities, and even households, across the globe. The IAEA is committed to doing everything it can to make peaceful nuclear technology available to help give all the children of the world a brighter future

  4. Focus on uranium research in Senegal

    International Nuclear Information System (INIS)

    Kanoute, M.

    2014-01-01

    Two periods stand out in the history of mining exploration for uranium in Senegal: • 1957 - 1965 in the context of a general inventory of the uranium potential of Africa, which is also the time that the large deposits of Niger and Gabon were discovered; • 1973 to the present, is characterized by surveys more focused on specific topics such as Birrimian Superior Precambrian Sedimentary, Secondary and Tertiary Phosphates. The collapse of uranium price that began since 1980 calls into question the validity of these surveys on areas away from the coast that lack infrastructure and forces the elimination of targets where there is little hope of finding high enough concentrations of uranium for possible mining.

  5. Bursting of filaments in the plasma focus

    International Nuclear Information System (INIS)

    Gratton, F.T.L.

    1976-01-01

    Photographs of the current sheath of (low energy) plasma focus show a disruption of the filaments. This phenomenon is interpreted as a vortex breakdown. Physical parameters which support this hypothesis are obtained from measurements, from the theoretical thickness of the current sheath given by Nardi and from some models of the plasma flow. The widening of a vortex due to axial velocity increase is analyzed by means of magnetohydrodynamic collinear models. The main results are: (1) the existence of a limit separating supercritical from subcritical regimes (their character changes with the ratio between kinetic and magnetic energy); (2) the existence of flow regimes where the vortex radius remains approximately constant for moderate increments of the external velocity; (3) the structure of the vortex may change substantially for a sufficiently large increment of the external velocity, even in subcritical states; (4) the possibility that a burst of the vortex may occur when the external velocity suffers a slowdown

  6. Electron beam production by a plasma focus

    International Nuclear Information System (INIS)

    Smith, J.R.; Luo, C.M.; Schneider, R.F.; Rhee, M.J.

    1984-01-01

    Operation of a plasma focus as a Compact Pulsed Accelerator (CPA) for ions has been previously reported. The CPA consists of: (1) a 15 μF, 3 kJ capacitor, (2) a triggered spark gap, (3) a coaxial transmission line, and (4) a Mather geometry plasma gun. Recently the authors have investigated application of the CPA as an accelerator for electrons. In the previously reported work using the standard Mather plasma gun geometry, ions were accelerated away from the plasma gun and were therefore conveniently extracted for analysis, but electrons were directed into the hollow anode where extraction is blocked by the coaxial transmission line. For investigation of accelerated electrons a new plasma gun design which allows extraction of electrons has been developed. Details of the new plasma gun design and further results of beam diagnostics are discussed

  7. Focusing mechanisms in the Pulselac CU accelerator

    International Nuclear Information System (INIS)

    Johnson, D.J.; Lockner, T.R.

    1986-06-01

    The post-acceleration of a 400 keV, 10 kA proton beam by a 200 kV magnetically insulated gap is investigated. The deflection from self and applied E and B fields are measured and compared to calculated values. We find that the beam is inadequately space-charge neutralized without gas puffs in regions of applied-B field to allow efficient transport. The beam is also non-current neutralized in these regions leading to self-magnetic deflection. The applied-B field is used to focus the beam both directly as a solenoidal lens and indirectly by defining the equipotential surfaces in the accelerating gap. It is also pointed out how azimuthal asymmetries in the beam current density and cathode plasma cause beam self-field asymmetries that lead to emittance growth. 4 refs., 4 figs

  8. Review of reasearch and technical development focused

    Directory of Open Access Journals (Sweden)

    Slavkovský Marián

    1998-12-01

    Full Text Available Treatment of flotation tetrahedrite concentrates produced from the of ore mined in the Rudňany and Rožňava ore deposits is a very complex technological problem. This problem has not been solved succesfuly so far. The presence and quality of undesired metal components such as antimony and mercury in the product of a wet ore dressing is a limiting factor for subsequent metalurgical process to obtain pure metal copper and/or silver in copper smelter plants. This factor has been the principal reason of a great effort provided in this respects by both, manufacturers and reaserchers mainly in the last 25 years. This article is focused on the summary of mentioned activities.

  9. Focus and domain of sustainability values

    DEFF Research Database (Denmark)

    Rask, Morten; Madsen, Ena Alvarado; Lauring, Jakob

    The increasing trend of globalization and environmental challenges make the understanding of sustainability issues in international business a growing challenge throughout the world. This study illustrates the challenge of an organization as it becomes larger and more diverse to keep the core val...... and trigger new ways of thinking and to facilitate corporate culture change through coordination and configuration of the system of values and beliefs regarding sustainability among employees in the company....... values alive. We focused a multinational with more than 30 years experience with sustainability. It is one of the worlds' top manufacturers of renewable energy equipment. We found an extreme diversity in understanding sustainability. This exploratory study is based on a very broad sample within one...

  10. Consumer focus can spur group practice turnaround.

    Science.gov (United States)

    Foreman, M S; Draper, A

    2001-06-01

    Many healthcare organizations have lost money on their employed group practices. The solution to this dilemma is not necessarily divestment of the group practices. Instead, some healthcare organizations should view their physicians as an asset. Healthcare organizations and physicians need to develop a new framework for their relationship to optimize their competitive advantage. Three guiding principles that will help accomplish this objective are to recast the healthcare organization-physician relationship to focus on the consumer, reconfigure the economic model to exceed consumer demands, and restructure the group practice to encourage fiscal and service excellence. In developing a new relationship framework, the stakeholders need to define the group practice's mission, strategic direction, composition, infrastructure, compensation model, and structure.

  11. Literature in Focus Perspectives on LHC Physics

    CERN Multimedia

    2008-01-01

    The CERN Library invites you to a book presentation, a Literature in Focus event. The Large Hadron Collider (LHC) will be the world’s largest, highest energy and highest intensity particle accelerator. This is a timely book with several perspectives on the hoped-for discoveries from the LHC. This book provides an overview of the techniques that will be crucial for finding new physics at the LHC, as well as perspectives on the importance and implications of the discoveries. Among the accomplished contributors to this book are leaders and visionaries in the field of particle physics beyond the Standard Model, including two Nobel Laureates (Steven Weinberg and Frank Wilczek). With its blend of popular and technical contents, the book will have wide appeal, not only to physical scientists but also to those in related fields. Perspectives on LHC Physics (World Scientific Publishing) Gordon Kane and Aaron Pierce (eds.) Tuesday 12 August, 4.30pm Council Chamber Refresh...

  12. Focused ion beam technology and ultimate applications

    International Nuclear Information System (INIS)

    Gierak, Jacques

    2009-01-01

    In this topical review, the potential of the focused ion beam (FIB) technology and ultimate applications are reviewed. After an introduction to the technology and to the operating principles of liquid metal ion sources (LMIS), of ion optics and instrument architectures, several applications are described and discussed. First, the application of FIB for microcircuit inspection, metrology and failure analysis is presented. Then, we introduce and illustrate some advanced patterning schemes we propose as next generation FIB processing examples. These patterning schemes are (i) local defect injection or smoothing in magnetic thin film direct patterning, (ii) functionalization of graphite substrates to guide organization of clusters, (iii) local and selective epitaxy of III–V semiconductor quantum dots and (iv) FIB patterned solid-state nanopores for biological molecules manipulation and analysis. We conclude this work by giving our vision of the future developments for FIB technology. (topical review)

  13. Diagnosis - the limiting focus of taxonomy.

    Science.gov (United States)

    Sturmberg, Joachim P; Martin, Carmel M

    2016-02-01

    The focus on the diagnosis is a pivotal aspect of medical practice since antiquity. Diagnostic taxonomy helped to categorize ailments to improve medical care, and in its social sense resulted in validation of the sick role for some, but marginalization or stigmatization for others. In the medical industrial complex, diagnostic taxonomy structured health care financing, management and practitioner remuneration. However, with increasing demands from multiple agencies, there are increasing unintended and unwarranted consequences of our current taxonomies and diagnostic processes resulting from the conglomeration of underpinning concepts, theories, information and motivations. We argue that the increasing focus on the diagnosis resulted in excessive compartmentalization - 'partialism' - of medical practice, diminishing medical care and being naively simplistic in light of the emerging understanding of the interconnected nature of the diseasome. The human is a complex organic system of interconnecting dynamics and feedback loops responding to internal and external forces including genetic, epigenetic and environmental attractors, rather than the sum of multiple discrete organs which can develop isolated diseases or multiple morbidities. Solutions to these unintended consequences of many contemporary health system processes involve revisiting the nature of diagnostic taxonomies and the processes of their construction. A dynamic taxonomic framework would shift to more relevant attractors at personal, clinical and health system levels recognizing the non-linear nature of health and disease. Human health at an individual, group and population level is the ability to adapt to internal and external stressors with resilience throughout the life course, yet diagnostic taxonomies are increasingly constructed around fixed anchors. Understanding diagnosis as dissecting, pigeonholing or bean counting (learning by dividing) is no longer useful, the challenge for the future is to

  14. Kinetics of cesium lead halide perovskite nanoparticle growth; focusing and de-focusing of size distribution

    Science.gov (United States)

    Koolyk, Miriam; Amgar, Daniel; Aharon, Sigalit; Etgar, Lioz

    2016-03-01

    In this work we study the kinetics of cesium lead halide perovskite nanoparticle (NP) growth; the focusing and de-focusing of the NP size distribution. Cesium lead halide perovskite NPs are considered to be attractive materials for optoelectronic applications. Understanding the kinetics of the formation of these all-inorganic perovskite NPs is critical for reproducibly and reliably generating large amounts of uniformly sized NPs. Here we investigate different growth durations for CsPbI3 and CsPbBr3 NPs, tracking their growth by high-resolution transmission electron microscopy and size distribution analysis. As a result, we are able to provide a detailed model for the kinetics of their growth. It was observed that the CsPbI3 NPs exhibit focusing of the size distribution in the first 20 seconds of growth, followed by de-focusing over longer growth durations, while the CsPbBr3 NPs show de-focusing of the size distribution starting from the beginning of the growth. The monomer concentration is depleted faster in the case of CsPbBr3 than in the case of CsPbI3, due to faster diffusion of the monomers, which increases the critical radius and results in de-focusing of the population. Accordingly, focusing is not observed within 40 seconds of growth in the case of CsPbBr3. This study provides important knowledge on how to achieve a narrow size distribution of cesium lead halide perovskite NPs when generating large amounts of these promising, highly luminescent NPs.In this work we study the kinetics of cesium lead halide perovskite nanoparticle (NP) growth; the focusing and de-focusing of the NP size distribution. Cesium lead halide perovskite NPs are considered to be attractive materials for optoelectronic applications. Understanding the kinetics of the formation of these all-inorganic perovskite NPs is critical for reproducibly and reliably generating large amounts of uniformly sized NPs. Here we investigate different growth durations for CsPbI3 and CsPbBr3 NPs, tracking

  15. Competitive mindsets, creativity, and the role of regulatory focus

    NARCIS (Netherlands)

    Bittner, Jenny; Heidemeier, Heike

    2013-01-01

    We examined how regulatory focus and intentions to compete rather than cooperate with group members relate to creativity. Study 1 showed that a promotion focus (i.e., a focus on ideals) activated a cooperative mindset, whereas a prevention focus (i.e., a focus on responsibilities) activated a

  16. Foreword: Focus on Superconductivity in Semiconductors

    Directory of Open Access Journals (Sweden)

    Yoshihiko Takano

    2008-01-01

    Full Text Available Since the discovery of superconductivity in diamond, much attention has been given to the issue of superconductivity in semiconductors. Because diamond has a large band gap of 5.5 eV, it is called a wide-gap semiconductor. Upon heavy boron doping over 3×1020 cm−3, diamond becomes metallic and demonstrates superconductivity at temperatures below 11.4 K. This discovery implies that a semiconductor can become a superconductor upon carrier doping. Recently, superconductivity was also discovered in boron-doped silicon and SiC semiconductors. The number of superconducting semiconductors has increased. In 2008 an Fe-based superconductor was discovered in a research project on carrier doping in a LaCuSeO wide-gap semiconductor. This discovery enhanced research activities in the field of superconductivity, where many scientists place particular importance on superconductivity in semiconductors.This focus issue features a variety of topics on superconductivity in semiconductors selected from the 2nd International Workshop on Superconductivity in Diamond and Related Materials (IWSDRM2008, which was held at the National Institute for Materials Science (NIMS, Tsukuba, Japan in July 2008. The 1st workshop was held in 2005 and was published as a special issue in Science and Technology of Advanced Materials (STAM in 2006 (Takano 2006 Sci. Technol. Adv. Mater. 7 S1.The selection of papers describe many important experimental and theoretical studies on superconductivity in semiconductors. Topics on boron-doped diamond include isotope effects (Ekimov et al and the detailed structure of boron sites, and the relation between superconductivity and disorder induced by boron doping. Regarding other semiconductors, the superconducting properties of silicon and SiC (Kriener et al, Muranaka et al and Yanase et al are discussed, and In2O3 (Makise et al is presented as a new superconducting semiconductor. Iron-based superconductors are presented as a new series of high

  17. CATE 2016 Indonesia: Optics and Focus Strategy

    Science.gov (United States)

    McKay, M. A.; Jenson, L.; Kovac, S. A.; Bosh, R.; Mitchell, A. M.; Hare, H. S.; Watson, Z.; Penn, M. J.

    2016-12-01

    The 2017 solar eclipse will be a natural phenomenon that will sweep across the United State would provide an excellent opportunity to observe and study the solar corona. The Citizens Continental Astronomical Telescopic Eclipse (CATE) Experiment directed my Matt Penn, intends to take advantage of this scientific opportunity by organizing 60 sites along the path of totality from Oregon to South Carolina to observe the eclipse and make a 90 min continuous video of the solar corona. The preliminary observation was done with the 2016 eclipse in Indonesia, with 5 sites along the path of totality. The sites were provided with an 80mm diameter Telescope with a 480mm focal length with an extension tube, Celestron equatorial mount, a CMOS camera, a Dell dual processor running Windows, GPS and an Arduino box, more details will be provided. I observed at the furthest east site in Ternate, Indonesia, with Dr. Donald Walter. The day of the eclipse we had clouds but still had a successful observation. The observation was successful with 4 out of the 5 sites collected eclipse data, due to weather the other site was not able to observe. The data was then collected and processed over the summer. To prepare for the observation in 2017, the 60 sites will be provided with the equipment, software and training. The groups will then practice by doing solar and lunar observations, where they will follow an almost identical procedure for the eclipse to do their observations. These test will increase our chances to have a successful observation among all sites. The focus will play a crucial role in this observation to provide a high quality image. Currently, a new focusing method using an image derivative method to provide quantitative feedback to the user is being developed. Finally, a Graphical User Interface is also being developed using the codes produces from the summer 2016 data analysis, to process the images from each site with minimal effort and produce quality scientific images

  18. Anode plasma and focusing reb diodes

    International Nuclear Information System (INIS)

    Goldstein, S.A.; Swain, D.W.; Hadley, G.R.; Mix, L.P.

    1975-01-01

    The use of electrical, optical, x-ray, and particle diagnostics to characterize the production of anode plasma and to monitor its influence on beam generation and focusing is reviewed. Studies using the Nereus accelerator show that after cathode turn-on, deposition of several kJ/gm on the anode is necessary before ions from hydrocarbons, adsorbed gases, and heavier metallic species are detected. The actual time at which ions are liberated depends on several factors, one of which is the specific heat of the anode substrate. Once formed, anode ions cross the A-K gap (with an energy equal to the diode voltage) and interact with the cathode to produce an axially peaked beam profile, a ''pinch'' which does not follow the critical current criterion. Experiments with externally generated anode plasma show that this type of pinch can be attracted to localized areas on the anode. Preliminary observations on Hydra indicate the anode plasma composition is similar to that on Nereus. The effect of this plasma on pinch dynamics currently is under investigation

  19. Safety climate and firefighting: Focus group results.

    Science.gov (United States)

    DeJoy, David M; Smith, Todd D; Dyal, Mari-Amanda

    2017-09-01

    Firefighting is a hazardous occupation and there have been numerous calls for fundamental changes in how fire service organizations approach safety and balance safety with other operational priorities. These calls, however, have yielded little systematic research. As part of a larger project to develop and test a model of safety climate for the fire service, focus groups were used to identify potentially important dimensions of safety climate pertinent to firefighting. Analyses revealed nine overarching themes. Competency/professionalism, physical/psychological readiness, and that positive traits sometimes produce negative consequences were themes at the individual level; cohesion and supervisor leadership/support at the workgroup level; and politics/bureaucracy, resources, leadership, and hiring/promotion at the organizational level. A multi-level perspective seems appropriate for examining safety climate in firefighting. Safety climate in firefighting appears to be multi-dimensional and some dimensions prominent in the general safety climate literature also seem relevant to firefighting. These results also suggest that the fire service may be undergoing transitions encompassing mission, personnel, and its fundamental approach to safety and risk. These results help point the way to the development of safety climate measures specific to firefighting and to interventions for improving safety performance. Copyright © 2017 National Safety Council and Elsevier Ltd. All rights reserved.

  20. Kinetic Simulations of Dense Plasma Focus Breakdown

    Science.gov (United States)

    Schmidt, A.; Higginson, D. P.; Jiang, S.; Link, A.; Povilus, A.; Sears, J.; Bennett, N.; Rose, D. V.; Welch, D. R.

    2015-11-01

    A dense plasma focus (DPF) device is a type of plasma gun that drives current through a set of coaxial electrodes to assemble gas inside the device and then implode that gas on axis to form a Z-pinch. This implosion drives hydrodynamic and kinetic instabilities that generate strong electric fields, which produces a short intense pulse of x-rays, high-energy (>100 keV) electrons and ions, and (in deuterium gas) neutrons. A strong factor in pinch performance is the initial breakdown and ionization of the gas along the insulator surface separating the two electrodes. The smoothness and isotropy of this ionized sheath are imprinted on the current sheath that travels along the electrodes, thus making it an important portion of the DPF to both understand and optimize. Here we use kinetic simulations in the Particle-in-cell code LSP to model the breakdown. Simulations are initiated with neutral gas and the breakdown modeled self-consistently as driven by a charged capacitor system. We also investigate novel geometries for the insulator and electrodes to attempt to control the electric field profile. The initial ionization fraction of gas is explored computationally to gauge possible advantages of pre-ionization which could be created experimentally via lasers or a glow-discharge. Prepared by LLNL under Contract DE-AC52-07NA27344.

  1. KEY FACTORS IN MARKETING FOCUSED SERVICES BUSINESSES

    Directory of Open Access Journals (Sweden)

    Doris Yohanna Martínez Castrillón

    2016-07-01

    Full Text Available This article aims to identify the key success factors in the marketing area and describe them as managerial allies for companies that wish to position themselves in the market under a good sustainable performance , for it has been consulted theoretical references of Marketing as a management partner with collection and integration of data. Methodologically, it is located within the type of descriptive research field, with a design of transactional non-experimental, with an intentional non-probabilistic stratified sample of four reporting units. The findings established fifteen (15 points of influence called "key success factors (FCE in the area of marketing, and managerial allies of service companies in the security, surveillance and protection sector in industrial, commercial and residential sectors. Finally, it is intended that the actions of marketing service companies should focus to the welfare of both the organization, such as users, both in the environment, and economic, social and technological, characterized by ethics, sustainable development and transparency to respond appropriately.

  2. P3: a practice focused learning environment

    Science.gov (United States)

    Irving, Paul W.; Obsniuk, Michael J.; Caballero, Marcos D.

    2017-09-01

    There has been an increased focus on the integration of practices into physics curricula, with a particular emphasis on integrating computation into the undergraduate curriculum of scientists and engineers. In this paper, we present a university-level, introductory physics course for science and engineering majors at Michigan State University called P3 (projects and practices in physics) that is centred around providing introductory physics students with the opportunity to appropriate various science and engineering practices. The P3 design integrates computation with analytical problem solving and is built upon a curriculum foundation of problem-based learning, the principles of constructive alignment and the theoretical framework of community of practice. The design includes an innovative approach to computational physics instruction, instructional scaffolds, and a unique approach to assessment that enables instructors to guide students in the development of the practices of a physicist. We present the very positive student related outcomes of the design gathered via attitudinal and conceptual inventories and research interviews of students’ reflecting on their experiences in the P3 classroom.

  3. A process for risk-focused maintenance

    International Nuclear Information System (INIS)

    Lofgren, E.V.; Cooper, S.E.; Kurth, R.E.; Phillips, L.B.

    1991-03-01

    This report presents a process for focusing maintenance resources on components that enable nuclear plant systems to perform their essential functions and on components whose failure may initiate challenges to safety systems, so as to have the greatest impact in decreasing risk. The process provides criteria, based on risk, for deciding which components are critical to risk and determining what maintenance activities are required to ensure reliable operation of those risk-critical components. Two approaches are provided for selection of risk-critical components. One approach uses the results of a Probabilistic Risk Assessment (PRA); the other is based on the methodology developed for this report, which has a basis in PRA although it does not use the results of a PRA study. Following identification of risk-critical components, both approaches use a single methodology for determining what maintenance activities are required to ensure reliable operation of the identified components. The report also provides demonstrations of application of the two approaches to selection of risk-critical components and demonstrations of application of the methodology for determining what maintenance activities are required to an active standby safety system, a normally operating system, and passive components. 5 refs., 11 figs., 1 tab

  4. Strategies for osteochondral repair: Focus on scaffolds

    Directory of Open Access Journals (Sweden)

    Seog-Jin Seo

    2014-07-01

    Full Text Available Interest in osteochondral repair has been increasing with the growing number of sports-related injuries, accident traumas, and congenital diseases and disorders. Although therapeutic interventions are entering an advanced stage, current surgical procedures are still in their infancy. Unlike other tissues, the osteochondral zone shows a high level of gradient and interfacial tissue organization between bone and cartilage, and thus has unique characteristics related to the ability to resist mechanical compression and restoration. Among the possible therapies, tissue engineering of osteochondral tissues has shown considerable promise where multiple approaches of utilizing cells, scaffolds, and signaling molecules have been pursued. This review focuses particularly on the importance of scaffold design and its role in the success of osteochondral tissue engineering. Biphasic and gradient composition with proper pore configurations are the basic design consideration for scaffolds. Surface modification is an essential technique to improve the scaffold function associated with cell regulation or delivery of signaling molecules. The use of functional scaffolds with a controllable delivery strategy of multiple signaling molecules is also considered a promising therapeutic approach. In this review, we updated the recent advances in scaffolding approaches for osteochondral tissue engineering.

  5. A flexible cell concentrator using inertial focusing.

    Science.gov (United States)

    Tu, Chunglong; Zhou, Jian; Liang, Yitao; Huang, Bobo; Fang, Yifeng; Liang, Xiao; Ye, Xuesong

    2017-09-11

    Cell concentration adjustment is intensively implemented routinely both in research and clinical laboratories. Centrifuge is the most prevalent technique for tuning biosample concentration. But it suffers from a number of drawbacks, such as requirement of experienced operator, high cost, low resolution, variable reproducibility and induced damage to sample. Herein we report on a cost-efficient alternative using inertial microfluidics. While the majority of existing literatures concentrate on inertial focusing itself, we identify the substantial role of the outlet system played in the device performance that has long been underestimated. The resistances of the outlets virtually involve in defining the cutoff size of a given inertial filtration channel. Following the comprehensive exploration of the influence of outlet system, we designed an inertial device with selectable outlets. Using both commercial microparticles and cultured Hep G2 cells, we have successfully demonstrated the automated concentration modification and observed several key advantages of our device as compared with conventional centrifuge, such as significantly reduced cell loss (only 4.2% vs. ~40% of centrifuge), better preservation of cell viability and less processing time as well as the increased reproducibility due to absence of manual operation. Furthermore, our device shows high effectiveness for concentrated sample (e.g., 1.8 × 10 6 cells/ml) as well. We envision its promising applications in the circumstance where repetitive sample preparation is intensely employed.

  6. Bioprospecting Archaea: Focus on Extreme Halophiles

    KAUST Repository

    Antunes, André

    2016-12-12

    In 1990, Woese et al. divided the Tree of Life into three separate domains: Eukarya, Bacteria, and Archaea. Archaea were originally perceived as little more than “odd bacteria” restricted to extreme environmental niches, but later discoveries challenged this assumption. Members of this domain populate a variety of unexpected environments (e.g. soils, seawater, and human bodies), and we currently witness ongoing massive expansions of the archaeal branch of the Tree of Life. Archaea are now recognized as major players in the biosphere and constitute a significant fraction of the earth’s biomass, yet they remain underexplored. An ongoing surge in exploration efforts is leading to an increase in the (a) number of isolated strains, (b) associated knowledge, and (c) utilization of Archaea in biotechnology. They are increasingly employed in fields as diverse as biocatalysis, biocomputing, bioplastic production, bioremediation, bioengineering, food, pharmaceuticals, and nutraceuticals. This chapter provides a general overview on bioprospecting Archaea, with a particular focus on extreme halophiles. We explore aspects such as diversity, ecology, screening techniques and biotechnology. Current and future trends in mining for applications are discussed.

  7. A process for risk-focused maintenance

    Energy Technology Data Exchange (ETDEWEB)

    Lofgren, E.V.; Cooper, S.E.; Kurth, R.E.; Phillips, L.B. (Science Applications International Corp., McLean, VA (USA))

    1991-03-01

    This report presents a process for focusing maintenance resources on components that enable nuclear plant systems to perform their essential functions and on components whose failure may initiate challenges to safety systems, so as to have the greatest impact in decreasing risk. The process provides criteria, based on risk, for deciding which components are critical to risk and determining what maintenance activities are required to ensure reliable operation of those risk-critical components. Two approaches are provided for selection of risk-critical components. One approach uses the results of a Probabilistic Risk Assessment (PRA); the other is based on the methodology developed for this report, which has a basis in PRA although it does not use the results of a PRA study. Following identification of risk-critical components, both approaches use a single methodology for determining what maintenance activities are required to ensure reliable operation of the identified components. The report also provides demonstrations of application of the two approaches to selection of risk-critical components and demonstrations of application of the methodology for determining what maintenance activities are required to an active standby safety system, a normally operating system, and passive components. 5 refs., 11 figs., 1 tab.

  8. A point focusing double parabolic trough concentrator

    Energy Technology Data Exchange (ETDEWEB)

    Murphree, Quincy C. [Kentucky Mountain Bible College, Vancleve, KY (United States)

    2001-07-01

    This article shows that a point focusing solar concentrator can be made from two reflective parabolic troughs, a primary and a secondary, by orienting their longitudinal axes in perpendicular directions and separating them by the difference of their focal lengths along the optical axis. This offers a new alternative to the conventional 3-D paraboloidal concentrator permitting more flexibility in designs for applications requiring high concentrations. Both advantages and disadvantages are discussed. The intensity concentration ratio distribution is calculated in the focal plane and has elliptically shaped contours due to the inherent compensation of errant rays by the concave secondary. The ratio of the major to minor axes was 2.61 for the case considered, resulting in a concentration {approx}2.61 times that of a comparable concentrator without the compensation afforded by a concave secondary. Still, geometrical constraints limit the concentration to about 2000 suns for mirror quality errors of 5 mr. Optimisation of the compensation effect holds potential for improved performance for other concentrator designs. Finally, the functional dependence of the peak concentration and shading factor upon design parameters are presented. (Author)

  9. An electromagnetically focused electron beam line source

    International Nuclear Information System (INIS)

    Iqbal, Munawar; Masood, Khalid; Rafiq, Mohammad; Chaudhary, Maqbool A.; Aleem, Fazal-e-

    2003-01-01

    A directly heated thermionic electron beam source was constructed. A tungsten wire of length 140 mm with diameter 0.9 mm was used as a cathode. An emission current of 5000 mA was achieved at an input heating power of 600 W. Cathode to anode distance of 6 mm with acceleration voltage of 10 kV was used. A uniform external magnetic field of 50 G was employed to obtain a well-focused electron beam at a deflection of 180 deg., with cathode to work site distance of 130 mm. Dimensions of the beam (1.25x120 mm) recorded at the work site were found to be in good agreement with the designed length of cathode. The deformation of the cathode was overcome by introducing a spring action mechanism, which gives uniform emission current density throughout the emission surface. We have achieved the saturation limit of the designed source resulting in smooth and swift operation of the gun for many hours (10-15 h continuously). The design of gun is so simple that it can accommodate longer cathodes for obtaining higher emission values. This gun has made it possible to coat large substrate surfaces at much faster evaporation rate at lower cost. It can also be useful in large-scale vacuum metallurgy plants for melting, welding and heat treatment

  10. National Ignition Facility design focuses on optics

    International Nuclear Information System (INIS)

    Hogan, W.J.; Atherton, L.J.; Paisner, J.A.

    1996-01-01

    Sometime in the year 2002, scientists at the National Ignition Facility (NIF) will focus 192 separate high-power ultraviolet laser beams onto a tiny capsule of deuterium and tritium, heating and compressing the material until it ignites and burns with a burst of fusion energy. The mission of NIF, which will contain the largest laser in the world, is to obtain fusion ignition and gain and to use inertial confinement fusion capabilities in nuclear weapons science experiments. The physics data provided by NIF experiments will help scientists ensure nuclear weapons reliability without the need for actual weapons tests; basic sciences such as astrophysics will also benefit. The facility faces stringent weapons-physics user requirements demanding peak pulse powers greater than 750 TW at 0.35 microm (only 500 TW is required for target ignition), pulse durations of 0.1 to 20 ns, beam steering on the order of several degrees, and target isolation from residual 1- and 0.5-microm radiation. Additional requirements include 50% fractional encircled beam energy in a 100-microm-diameter spot, with 95% encircled in a 200-microm spot. The weapons-effects community requires 1- and 0.5-microm light on target, beam steering to widely spaced targets, a target chamber accommodating oversized objects, well-shielded diagnostic areas, and elimination of stray light in the target chamber. The beamline design, amplifier configuration and requirements for optics are discussed here

  11. Arco chimie focuses on PA at FOS

    International Nuclear Information System (INIS)

    Jackson, D.

    1992-01-01

    Arco Chimie France (Fos-sur-Mer), at a recent meeting at its southern France manufacturing site, emphasized that future strategy is strongly focused on its propylene oxide (PO) and derivatives activities. The F2.5 billion ($466 million)-Fe billion/year operation manufactures 200,000 m.t./year of PO, about 70% for captive use and the balance for the merchant market; 550,000 m.t./year of methyl tert butyl ether (MTBE); 97,000 m.t./year of polyols; and 70,000 m.t./year of propylene glycols. There has been talk of Arco modifying its Fos MTBE plant to make it flexible for ethyl tert-butyl ether (ETBE) output; the parent company already operates an MTBE/ETBE pilot unit at Corpus Christi, TX. But Arco Chimie notes there is insufficient bioethanol feedstock availability to convert all production to ETBE. The company would also require investment in new storage capacity for ethanol and ETBE. However, France's biofuels program is not yet clearly defined, and it is politically sensitive because it depends heavily on government subsidies offered to farmers. That, says Arco, makes it impossible to have an accurate idea of how much ethanol will be available

  12. PROFICIENT CLASSROOM MANAGEMENT THROUGH FOCUSED MATHEMATIC TEACHING

    Directory of Open Access Journals (Sweden)

    Marcus Samuelsson

    2017-12-01

    Full Text Available A not entirely unusual position among teachers is that they believe that they must first establish a peaceful classroom before they can begin to teach the subject. This research, shows how a proficient mathematics teacher teaches his subject and thereby creates a quiet and focused classroom and exerts effective leadership, just by teaching mathematics. The researchers observed a male mathematics teacher for almost half a year, i.e. one semester. The results of research present several patterns that the researchers saw during the observations of his teaching. The teacher showed an interest in each student’s mathematical thinking and expressed explicitly how students were expected to learn mathematics. He also directed students’ attention to mathematics and established a culture where all solutions were important in the teaching process. In the teaching process, he used multiple representations to motivate students and a lot of supportive expressions that made them feel that they were able to learn mathematics. He worked patiently to establish structures, and there was almost no disruptive behaviour. Students simply did not have time to interfere because they were so engaged in learning mathematics.

  13. Mixed Waste Focus Area - Waste form initiative

    International Nuclear Information System (INIS)

    Nakaoka, R.; Waters, R.; Pohl, P.; Roach, J.

    1998-01-01

    The mission of the US Department of Energy's (DOE) Mixed Waste Focus Area (MWFA) is to provide acceptable technologies that enable implementation of mixed waste treatment systems which are developed in partnership with end-users, stakeholders, tribal governments, and regulators. To accomplish this mission, a technical baseline was established in 1996 and revised in 1997. The technical baseline forms the basis for determining which technology development activities will be supported by the MWFA. The primary attribute of the technical baseline is a set of prioritized technical deficiencies or roadblocks related to implementation of mixed waste treatment systems. The Waste Form Initiative (WFI) was established to address an identified technical deficiency related to waste form performance. The primary goal of the WFI was to ensure that the mixed low-level waste (MLLW) treatment technologies being developed, currently used, or planned for use by DOE would produce final waste forms that meet the waste acceptance criteria (WAC) of the existing and/or planned MLLW disposal facilities. The WFI was limited to an evaluation of the disposal requirements for the radioactive component of MLLW. Disposal requirements for the hazardous component are dictated by the Resource Conservation and Recovery Act (RCRA), and were not addressed. This paper summarizes the technical basis, strategy, and results of the activities performed as part of the WFI

  14. Treatment of Movement Disorders With Focused Ultrasound

    Directory of Open Access Journals (Sweden)

    Paul S Fishman

    2017-05-01

    Full Text Available Although the use of ultrasound as a potential therapeutic modality in the brain has been under study for several decades, relatively few neuroscientists or neurologists are familiar with this technology. Stereotactic brain lesioning had been widely used as a treatment for medically refractory patients with essential tremor (ET, Parkinson disease (PD, and dystonia but has been largely replaced by deep brain stimulation (DBS surgery, with advantages both in safety and efficacy. However, DBS is associated with complications including intracerebral hemorrhage, infection, and hardware malfunction. The occurrence of these complications has spurred interest in less invasive stereotactic brain lesioning methods including magnetic resonance imaging–guided high intensity–focused ultrasound (FUS surgery. Engineering advances now allow sound waves to be targeted noninvasively through the skull to a brain target. High intensities of sonic energy can create a coagulation lesion similar to that of older radiofrequency stereotactic methods, but without opening the skull, recent Food and Drug Administration approval of unilateral thalamotomy for treatment of ET. Clinical studies of stereotactic FUS for aspects of PD are underway. Moderate intensity, pulsed FUS has also demonstrated the potential to safely open the blood-brain barrier for localized delivery of therapeutics including proteins, genes, and cell-based therapy for PD and related disorders. The goal of this review is to provide basic and clinical neuroscientists with a level of understanding to interact with medical physicists, biomedical engineers, and radiologists to accelerate the application of this powerful technology to brain disease

  15. Linear collider IR and final focus introduction

    International Nuclear Information System (INIS)

    Irwin, J.; Burke, D.

    1991-09-01

    The Linear Collider subgroup of the Accelerator Physics working group concerned itself with all aspects of the Next Linear Collider (NLC) design from the end of the accelerating structure to and through the interaction region. Within this region are: (1) a collimation section, (2) muon protection (of the detector from the collimator), (3) final focus system, (4) interaction point physics, and (5) detector masking from synchrotron radiation and beam-beam pair production. These areas of study are indicated schematically in Fig. 1. The parameters for the Next Linear Collider are still in motion, but attention has settled on a handful of parameter sets. Energies under consideration vary from 0.5 to 1.5 TeV in the center of mass, and luminosities vary from 10 33 to 10 34 cm -2 s -1 . To be concrete we chose as a guide for our studies the parameter sets labeled F and G, Table 1 from Palmer. These cover large and small crossing angle cases and 0.4 m to 1.8 m of free length at the interaction point

  16. Manipulation of Microbubble Clusters Using Focused Ultrasound

    Science.gov (United States)

    Matsuzaki, Hironobu; Osaki, Taichi; Kawaguchi, Kei; Unga, Johan; Ichiyanagi, Mitsuhisa; Azuma, Takashi; Suzuki, Ryo; Maruyama, Kazuo; Takagi, Shu

    2017-11-01

    In recent years, microbubbles (MBs) are expected to be utilized for the ultrasound drug delivery system (DDS). For the MB-DDS, it is important to establish a method of controlling bubbles and bubble clusters using ultrasound field. The objective of this study is to clarify behaviors of bubble clusters with various physical conditions. MBs in the ultrasound field are subjected to the primary Bjerknes force. The force traps MBs at the focal region of the focused ultrasound field. The trapped MBs form a bubble cluster at the region. A bubble cluster continues growing with absorbing surrounding bubbles until it reaches a maximum size beyond which it disappears from the focal region. In the present study, two kinds of MBs are used for the experiment. One is Sonazoid with average diameter of 2.6 um and resonant frequency of 5 MHz. The other is developed by Teikyo Univ., with average diameter of 1.5 um and presumed resonant frequency of 4 MHz. The bubble cluster's behaviors are analyzed using the high-speed camera. Sonazoid clusters have larger critical size than the other in every frequency, and its cluster size is inversely proportional to the ultrasound frequency, while Teikyo-bubble clusters have different tendency. These results are discussed in the presentation.

  17. Mixed waste focus area alternative technologies workshop

    International Nuclear Information System (INIS)

    Borduin, L.C.; Palmer, B.A.; Pendergrass, J.A.

    1995-01-01

    This report documents the Mixed Waste Focus Area (MWFA)-sponsored Alternative Technology Workshop held in Salt Lake City, Utah, from January 24--27, 1995. The primary workshop goal was identifying potential applications for emerging technologies within the Options Analysis Team (OAT) ''wise'' configuration. Consistent with the scope of the OAT analysis, the review was limited to the Mixed Low-Level Waste (MLLW) fraction of DOE's mixed waste inventory. The Los Alamos team prepared workshop materials (databases and compilations) to be used as bases for participant review and recommendations. These materials derived from the Mixed Waste Inventory Report (MWIR) data base (May 1994), the Draft Site Treatment Plan (DSTP) data base, and the OAT treatment facility configuration of December 7, 1994. In reviewing workshop results, the reader should note several caveats regarding data limitations. Link-up of the MWIR and DSTP data bases, while representing the most comprehensive array of mixed waste information available at the time of the workshop, requires additional data to completely characterize all waste streams. A number of changes in waste identification (new and redefined streams) occurred during the interval from compilation of the data base to compilation of the DSTP data base with the end result that precise identification of radiological and contaminant characteristics was not possible for these streams. To a degree, these shortcomings compromise the workshop results; however, the preponderance of waste data was linked adequately, and therefore, these analyses should provide useful insight into potential applications of alternative technologies to DOE MLLW treatment facilities

  18. Focus group discussion in mathematical physics learning

    Science.gov (United States)

    Ellianawati; Rudiana, D.; Sabandar, J.; Subali, B.

    2018-03-01

    The Focus Group Discussion (FGD) activity in Mathematical Physics learning has helped students perform the stages of problem solving reflectively. The FGD implementation was conducted to explore the problems and find the right strategy to improve the students' ability to solve the problem accurately which is one of reflective thinking component that has been difficult to improve. The research method used is descriptive qualitative by using single subject response in Physics student. During the FGD process, one student was observed of her reflective thinking development in solving the physics problem. The strategy chosen in the discussion activity was the Cognitive Apprenticeship-Instruction (CA-I) syntax. Based on the results of this study, it is obtained the information that after going through a series of stages of discussion, the students' reflective thinking skills is increased significantly. The scaffolding stage in the CA-I model plays an important role in the process of solving physics problems accurately. Students are able to recognize and formulate problems by describing problem sketches, identifying the variables involved, applying mathematical equations that accord to physics concepts, executing accurately, and applying evaluation by explaining the solution to various contexts.

  19. Improved focusing-and-deflection columns

    International Nuclear Information System (INIS)

    Mui, P.H.; Szilagyi, M.

    1995-01-01

    Our earlier design procedures for constructing quadrupole columns are further expanded to include octupole corrector units and ''octupole'' deflectors with no third-order harmonics. The additional complications are finer partitioning of the plates and increased number of voltage controllers. Two sample designs, one having only the additional octupole deflectors and one having both the deflectors and the correctors, are presented and compared to our previous quadrupole system. The additional octupole components are shown to be capable of increasing the current density from 30% to more than 300% for a four-plate system, designed to focus and scan the electron beam over a circular area of 0.25 mm radius. The electron beam is assumed to have an initial divergence of ±2.3 mrad, an initial energy of 6 kV, a total energy spread of 1 eV, and a final acceleration of 30 keV. These systems are then slightly reoptimized for a superficial comparison with the commercially available column by Micrion Corporation. The numerical results indicate a potential for substantial improvements, demonstrating the power of this design procedure. Finally, a discussion is presented on how the individual components can interact with each other to reduce the various aberrations. copyright 1995 American Vacuum Society

  20. Magnetized whirls in plasma focus discharges

    International Nuclear Information System (INIS)

    Witalis, E.

    1979-05-01

    The plasma focus is briefly described with emphasis on its capabilities as a neutron source. The filamentary whirl structures observed in the discharge plasma are described. Starting with a simple, early and particularly well established case of vorticity imparted by a rotational electric field to the plasma in MHD generators, a general derivation is then outlined proving that such magnetically induced rotation is a general feature for the normally Hall-conducting magnetized plasma. Physical interpretations of the effect are given and objections to it are critically reviewed as is also a theory proposing radiation cooling as the cause of plasma filamentation. A more detailed derivation based essentially on the consistent description of the motion and the field generation of the charged plasma particles yields a theoretical model where the specific features of magnetically compressed plasmas are found. In particular, the ion collisionless skin depth is obtained as the key length parameter. This length is identified as roughly the whirl radius. In conjunction with a generalized Bennett relation theoretical whirl properties are predicted and found to agree with observations. Mechanisms that relate the whirls to nuclear fusion reaction conditions are tentatively indicated. (author)

  1. Literature in focus: A Berlin Romance

    CERN Multimedia

    2005-01-01

    The CERN staff have many hidden talents. Who knows, maybe a colleague you see every day is actually a virtuoso violinist, an accomplished sportsman or an internationally renowned collector. Mathilde Fontanet, a translator in the CERN Translation and Minutes Service, is a writer in her spare time. Those who read her first essays in the Graviton no doubt spotted her talent. Following the publication of four short stories, her first novel, 'Rabenstrasse 5', was published in Switzerland in May 2005. Its backdrop is the busy Berlin arts faculty in the early 1980s. Lydia, a student, meets a young woman who leads her into some rather unusual activities. In parallel, two friends, both professors of literature, each record their thoughts and emotions in a diary. The paths of Lydia and the two professors are to cross... The novel will be published in France on 14 October. Mathilde Fontanet will present it in the framework of a forthcoming 'Literature in Focus' event in the CERN Library. Mathilde Fontanet'Rabenstras...

  2. Plasma focus - a pulsed radiation source

    International Nuclear Information System (INIS)

    Blagoev, Alexandar; Zapryanov, Stanislav; Gol'tsev, Vasilii; Gemishev, Orlin

    2014-01-01

    The article is devoted to the applications of plasma focus (PF) in radiobiology. Briefly describes the principle of operation of the device and the parameters of the PF type 'Mader' at the Physics Department of the University. Phase pinch discharge zones appear hot and dense plasma, which is a source of X-ray and neutron pulse when the working gas is deuterium. These radiations are essential for biological applications. Besides these bundles are obtained from accelerated charged particles and shock wave of ionized gas. Described are some of the contributions of other authors using PF in radiobiology. Given the results in the exposure of living organisms with soft X-ray emission of PF. We examined the viability of the cells of the two types of yeasts, after irradiation with X-rays at a dose of 65 mSv, where no change was found on the performance. It is shown that soft X-ray radiation doses on the order of tens of mSv, cause a significant change in the productivity of the electronic transport in the photosynthetic apparatus of Chlamydomonas reinhardtii. Trichoderma reesei M7 shows remarkable vitality irradiation with substantial doses of hard X-ray radiation (tens Sv). Appear endoglyukonazata changes in the protein component and the residual mass

  3. Autofocus system and autofocus method for focusing on a surface

    Science.gov (United States)

    O'Neill, Mary Morabito

    2017-05-23

    An autofocus system includes an imaging device, a lens system and a focus control actuator that is configured to change a focus position of the imaging device in relation to a stage. The electronic control unit is configured to control the focus control actuator to a plurality of predetermined focus positions, and activate the imaging device to obtain an image at predetermined positions and then apply a spatial filter to the obtained images. This generates a filtered image for the obtained images. The control unit determines a focus score for the filtered images such that the focus score corresponds to a degree of focus in the obtained images. The control unit identifies a best focus position by comparing the focus score of the filtered images, and controls the focus control actuator to the best focus position corresponding to the highest focus score.

  4. Technology of focus detection for 193nm projection lithographic tool

    Science.gov (United States)

    Di, Chengliang; Yan, Wei; Hu, Song; Xu, Feng; Li, Jinglong

    2012-10-01

    With the shortening printing wavelength and increasing numerical aperture of lithographic tool, the depth of focus(DOF) sees a rapidly drop down trend, reach a scale of several hundred nanometers while the repeatable accuracy of focusing and leveling must be one-tenth of DOF, approximately several dozen nanometers. For this feature, this article first introduces several focusing technology, Obtained the advantages and disadvantages of various methods by comparing. Then get the accuracy of dual-grating focusing method through theoretical calculation. And the dual-grating focusing method based on photoelastic modulation is divided into coarse focusing and precise focusing method to analyze, establishing image processing model of coarse focusing and photoelastic modulation model of accurate focusing. Finally, focusing algorithm is simulated with MATLAB. In conclusion dual-grating focusing method shows high precision, high efficiency and non-contact measurement of the focal plane, meeting the demands of focusing in 193nm projection lithography.

  5. Shifting focus to create knowledge collaboratively

    Directory of Open Access Journals (Sweden)

    Hanna Voog

    2013-12-01

    Full Text Available This paper presents a PhD-course called "Kick start to academic life - Information Management and Publication Process for Social Scientists", a collaboration between the Social Sciences Faculty Library at Lund University and professors at the Faculty. The objective of the course is to provide PhD candidates with generic knowledge about how to effectively conduct their PhD studies when it comes to information management and the publication processes. The course combines an introduction to the process of managing one's need of information as a PhD student, and an introduction to the process of managing the publication of one's results. The librarians have been involved in the development of this PhD course, from the first idea of a course in generic competences and on to the actual implementation. The Faculty of Social Science came up with the idea of a course like this in 2009, and asked two teachers/professors and two librarians to make an outline. We choose to focus on students in the beginning of their PhD studies, who would benefit most from it. We have now run it for 3 years (2010-2012, developed the course as for content and size, from demands from students and faculty as well as from our own experiences. Designing the course together, librarians and professors gained an insight into each other's competences and area of expertise. We used previous experiences from working with PhD students, like the providing of shorter courses, seminars and workshops. We choose a course design mixing lectures and workshops, in order to make the course both theoretical and practical. The course design also helped emphasizing aspects of the subject being discussed. One example is by adding a practical workshop in reference management program given by the librarians just after a lecture given by a professor about how and why academics cite. Another example is when we invite an editor of a high ranked peer-reviewed journal to talk about article submission from

  6. Interior's Climate Science Centers: Focus or Fail

    Science.gov (United States)

    Udall, B.

    2012-12-01

    ; (5) seek institutional stability; and (6) design processes for learning. In addition, CSC outputs should help decision makers to embrace and focus on uncertainty rather than on attempts to reduce uncertainty. Model building can be a useful exercise if used as a broad intellectual exercise to understand systems instead of narrow projection-based efforts. In some cases DOI agencies may want very simple products including scientific syntheses. Social science work including but not limited to economics and policy should be considered when appropriate to decision maker needs. One method for allocating CSC resources would involve a limited number of small scoping meetings with climate sensitive regional DOI agencies. In the Southwest, for example, regional entities would include at least the Landscape Conservation Cooperatives, National Park Service, Fish and Wildlife Service, Bureau of Land Management, Reclamation and the US Forest Service, a critically important land manager with a well-funded and well-structured climate program. Given DOI's trust responsibility to the tribes, at least one project should be focused on meeting those needs in this region. The goal of these meetings would be to identify a small number of projects each with adequate funding for interdisciplinary teams of university and USGS scientists and DOI decision makers. Done correctly, the CSCs should be able to leverage resources with these DOI partners.

  7. Two-focus fluorescence correlation spectroscopy

    International Nuclear Information System (INIS)

    Dertinger, T.

    2007-05-01

    Fluorescence Correlation Spectroscopy (FCS) has been invented more than 30 years ago and experienced a renaissance after stable and affordable laser sources and low-noise single-photon detectors have become available. Its ability to measure diffusion coefficients at nanomolar concentrations of analyte made it a widely used tool in biophysics. However, in recent years it has been shown by many authors that aberrational (e.g. astigmatism) and photophysical effects (e.g. optical saturation) may influence the result of an FCS experiment dramatically, so that a precise and reliable estimation of the diffusion coefficient is no longer possible. In this thesis, we report on the development, implementation, and application of a new and robust modification of FCS that we termed two-focus FCS (2fFCS) and which fulfils two requirements: (i) It introduces an external ruler into the measurement by generating two overlapping laser foci of precisely known and fixed distance. (ii) These two foci and corresponding detection regions are generated in such a way that the corresponding molecule detection functions (MDFs) are sufficiently well described by a simple two-parameter model yielding accurate diffusion coefficients when applied to 2fFCS data analysis. Both these properties enable us to measure absolute values of the diffusion coefficient with an accuracy of a few percent. Moreover, it will turn out that the new technique is robust against refractive index mismatch, coverslide thickness deviations, and optical saturation effects, which so often trouble conventional FCS measurements. This thesis deals mainly with the introduction of the new measurement scheme, 2fFCS, but also presents several applications with far-reaching importance. (orig.)

  8. Landfill stabilization focus area: Technology summary

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1995-06-01

    Landfills within the DOE Complex as of 1990 are estimated to contain 3 million cubic meters of buried waste. The DOE facilities where the waste is predominantly located are at Hanford, the Savannah River Site (SRS), the Idaho National Engineering Laboratory (INEL), the Los Alamos National Laboratory (LANL), the Oak Ridge Reservation (ORR), the Nevada Test Site (NTS), and the Rocky Flats Plant (RFP). Landfills include buried waste, whether on pads or in trenches, sumps, ponds, pits, cribs, heaps and piles, auger holes, caissons, and sanitary landfills. Approximately half of all DOE buried waste was disposed of before 1970. Disposal regulations at that time permitted the commingling of various types of waste (i.e., transuranic, low-level radioactive, hazardous). As a result, much of the buried waste throughout the DOE Complex is presently believed to be contaminated with both hazardous and radioactive materials. DOE buried waste typically includes transuranic-contaminated radioactive waste (TRU), low-level radioactive waste (LLW), hazardous waste per 40 CFR 26 1, greater-than-class-C waste per CFR 61 55 (GTCC), mixed TRU waste, and mixed LLW. The mission of the Landfill Stabilization Focus Area is to develop, demonstrate, and deliver safer,more cost-effective and efficient technologies which satisfy DOE site needs for the remediation and management of landfills. The LSFA is structured into five technology areas to meet the landfill remediation and management needs across the DOE complex. These technology areas are: assessment, retrieval, treatment, containment, and stabilization. Technical tasks in each of these areas are reviewed.

  9. Landfill stabilization focus area: Technology summary

    International Nuclear Information System (INIS)

    1995-06-01

    Landfills within the DOE Complex as of 1990 are estimated to contain 3 million cubic meters of buried waste. The DOE facilities where the waste is predominantly located are at Hanford, the Savannah River Site (SRS), the Idaho National Engineering Laboratory (INEL), the Los Alamos National Laboratory (LANL), the Oak Ridge Reservation (ORR), the Nevada Test Site (NTS), and the Rocky Flats Plant (RFP). Landfills include buried waste, whether on pads or in trenches, sumps, ponds, pits, cribs, heaps and piles, auger holes, caissons, and sanitary landfills. Approximately half of all DOE buried waste was disposed of before 1970. Disposal regulations at that time permitted the commingling of various types of waste (i.e., transuranic, low-level radioactive, hazardous). As a result, much of the buried waste throughout the DOE Complex is presently believed to be contaminated with both hazardous and radioactive materials. DOE buried waste typically includes transuranic-contaminated radioactive waste (TRU), low-level radioactive waste (LLW), hazardous waste per 40 CFR 26 1, greater-than-class-C waste per CFR 61 55 (GTCC), mixed TRU waste, and mixed LLW. The mission of the Landfill Stabilization Focus Area is to develop, demonstrate, and deliver safer,more cost-effective and efficient technologies which satisfy DOE site needs for the remediation and management of landfills. The LSFA is structured into five technology areas to meet the landfill remediation and management needs across the DOE complex. These technology areas are: assessment, retrieval, treatment, containment, and stabilization. Technical tasks in each of these areas are reviewed

  10. The 1998 annual: Focusing on asset quality

    International Nuclear Information System (INIS)

    1998-01-01

    Operational and financial activities of Newport Petroleum Corporation during fiscal year 1998 are reviewed. Despite the low oil prices, and the consequent reduction in industry activity and financial results, the Company continued to focus on high quality assets. The Company improved its proved and probable reserves by 21.3 million barrels of oil equivalent, increasing its reserve life index to over 10 years. Reserve addition costs in 1998 were a competitive $ 7.08 per barrel of oil equivalent. The Company produced more than 20,000 barrels of oil equivalent per day, generating revenue of $ 141 million. The Company acquired an interest in the Caroline Gas Unit for $ 165 million late in 1998 and experienced success with the drilling of two wells. At year end, reserves of approx. 575 bcf of raw gas in place were attributed to this area. New light oil discoveries were made in the Rigel area of northern British Columbia and the Shiningbank area of west-central Alberta. Both properties have significant development potential. While share price performance was essentially flat for the year, the target remains to add value on a per share basis over the long term. The outlook for natural gas appears to be positive, with markets expected to be robust with prices tracking supply/demand fundamentals. The completion of additional pipeline capacity from Alberta into U.S. markets has resulted in a lowering of the differential to U.S. prices, and as a result, it appears that pricing in western Canada will improve in the next several years. Although the outlook for oil prices remains uncertain, with recent OPEC commitments to curtail volumes, there is reason for cautious optimism. Overall, the Company is confident that it has the financial strength to not only weather an extended period of oil price weakness, but to continue to expand its activity levels and prosper

  11. Two-focus fluorescence correlation spectroscopy

    Energy Technology Data Exchange (ETDEWEB)

    Dertinger, T.

    2007-05-15

    Fluorescence Correlation Spectroscopy (FCS) has been invented more than 30 years ago and experienced a renaissance after stable and affordable laser sources and low-noise single-photon detectors have become available. Its ability to measure diffusion coefficients at nanomolar concentrations of analyte made it a widely used tool in biophysics. However, in recent years it has been shown by many authors that aberrational (e.g. astigmatism) and photophysical effects (e.g. optical saturation) may influence the result of an FCS experiment dramatically, so that a precise and reliable estimation of the diffusion coefficient is no longer possible. In this thesis, we report on the development, implementation, and application of a new and robust modification of FCS that we termed two-focus FCS (2fFCS) and which fulfils two requirements: (i) It introduces an external ruler into the measurement by generating two overlapping laser foci of precisely known and fixed distance. (ii) These two foci and corresponding detection regions are generated in such a way that the corresponding molecule detection functions (MDFs) are sufficiently well described by a simple two-parameter model yielding accurate diffusion coefficients when applied to 2fFCS data analysis. Both these properties enable us to measure absolute values of the diffusion coefficient with an accuracy of a few percent. Moreover, it will turn out that the new technique is robust against refractive index mismatch, coverslide thickness deviations, and optical saturation effects, which so often trouble conventional FCS measurements. This thesis deals mainly with the introduction of the new measurement scheme, 2fFCS, but also presents several applications with far-reaching importance. (orig.)

  12. Meaning-focused vs Form-focused L2 Instruction: Implications for ...

    African Journals Online (AJOL)

    KATEVG

    focus-on-meaning approach to English language instruction) compare with ... L2 use. Proponents of this view are concerned with the question of how this conversion ... processing, it may draw learners' attention to "notice" the form of the target ...

  13. Direct marketing of parenting programs: comparing a promotion-focused and a prevention-focused strategy.

    Science.gov (United States)

    Salari, Raziye; Backman, Anna

    2017-06-01

    : For parenting programs to achieve a public health impact, it is necessary to develop more effective marketing strategies to increase public awareness of these programs and promote parental participation. In this article, we compared a promotion-focused and a prevention-focused strategy via two studies. : We designed two ads inviting parents to participate in a universal parenting program; one ad focused on the program increasing the likelihood of positive outcomes for children (promotion-focused) and the other on the program reducing the likelihood of negative outcomes (prevention-focused). In study I, the two ads were run online simultaneously. Those who clicked on an ad were directed to a website where they could read about and sign up for the program. In study II, a community sample of 706 parents answered a questionnaire about the ads. : In study I, over 85 days, the prevention ad generated more clicks. There was no difference in the number of pages visited on the website nor in the number of parents who signed up for the program. In study II, parents showed a preference for the promotion ad, perceiving it as more relevant and rating it as more effective in getting them interested in the program. : A prevention strategy may be more effective in drawing public attention, in general. However, a promotion strategy is more likely to reach parents, in particular, and inspire them to consider participating in parenting programs. These strategies should be developed further and tested in both general and clinical populations. © The Author 2016. Published by Oxford University Press on behalf of the European Public Health Association. All rights reserved.

  14. Epizootic pertussis focus of hamadryad baboons

    Directory of Open Access Journals (Sweden)

    A. Yu. Medkova

    2015-01-01

    Full Text Available The absence of an adequate experimental animal model makes difficult study of immunity against whooping cough and its pathogenesis. Experimental whooping cough reported by us earlier in pubescent non-human primates of the Old World was accompanied by specific clinical and laboratory marks in the absence of cough. The possibility of pertussis modelling while experimental whooping cough in impuberal hamadryad baboons was investigated. In the process of selection of monkeys for the further studies for perfecting of experimental model for pertussis research unexpectedly were detected specific pertussis antibodies in impuberal hamadryad baboons.The aim of the study: revealing of source of infection and transmission of pertussis to hamadryad baboons and investigation of response of antibody-positive impuberal hamadryad baboons to secondary contagion by B. pertussis bacteria while experimental infection.Results. 18 veterinary checked, somatically healthy hamadryad baboons of various gender managed in two neighboring cages. Specific pertussis IgM and IgG antibodies were found in blood serum of all the animals and one of the monkey keepers. By real-time PCR in nasopharyngeal swabs of the monkey keeper and three 7- and 9-month-old hamadryad baboons were registered single B. pertussis genom equivalents. Seropositive impuberal hamadryad baboons were experimentally challenged by virulent B. pertussis 475 strain. Quantity of B. pertussis genom equivalents and percentage of IgM and IgG antibodies in impuberal hamadryad baboons after experimental infection were detected. These results were comparable with such received after secondary experimental challenge of monkeys by B. pertussis. Humoral immuneresponse was characterized by booster effect and rapid B. pertussis elimination.Conclusion. The case of transmission of B.pertussis bacteria to hamadryad baboons by natural contagion and epizootic focus of pertussis in apery conditions

  15. From field evaporation to focused ion beams

    International Nuclear Information System (INIS)

    Forbes, R.G.

    2004-01-01

    Full text: This paper report various items of recent progress in the theory of field evaporation and the theory of the liquid-metal ion source. The research has, in part, been driven by a desire to find out how to reduce the beam-spot size in a focused ion beam machine, which is developing as a significant tool of nanotechnology. A major factor in determining beam spot size seems to be the behavior of the liquid-metal ion source (LMIS), and one route might be to reduce the minimum emission current of a LMIS, if this is possible. Theories of LMIS minimum emission current have been re-examined. Some progress has been made, but development of more accurate theory has been constrained by several factors, include the long-known limitations of the present theory of field evaporation (FEV). This, in turn, has stimulated a wider re-examination of FEV theory. As part of some general theoretical remarks, the following items of recent progress will be covered. Various results concerning the prediction of the field F e at which the activation energy Q for field evaporation is zero, including calculations in which vacuum electrostatic energy changes are taken into account, and another look at the views of Kingham and Tsong concerning escape charge-state. Some years ago, the following approximate formula was derived for the dependence of FEV activation energy on field F: Q=B(F e /F - 1) 2 . It has recently been possible to show that the parameter B can be estimated as B= βYΩ/8, where Y is Young's modulus, Ω is the atomic volume, and β is a correction factor of order. In the framework of the charge-draining mechanism, another look at how the activation-energy hump can be modelled, in order to predict/explain the conditions under which FEV becomes dominated by ion tunnelling rather than field evaporation. A review of the changes in LMIS theory that result from applying the equation of continuity to the metal/vacuum interface, including modifications to the theory of minimum

  16. Focusing: coming to the point in metamaterials

    Science.gov (United States)

    Guenneau, S.; Diatta, A.; McPhedran, R. C.

    2010-04-01

    This paper reviews some properties of lenses in curved and folded optical spaces. The point of the paper is to show some limitations of geometrical optics in the analysis of subwavelength focusing. We first provide a comprehensive derivation for the equation of geodesics in curved optical spaces, which is a tool of choice to design metamaterials in transformation optics. We then analyse the resolution of the image of a line source radiating in the Maxwell fisheye and the Veselago-Pendry slab lens. The former optical medium is deduced from the stereographic projection of a virtual sphere and displays a heterogeneous refractive index n(r) which is proportional to the inverse of 1 + r 2. The latter is described by a homogeneous, but negative, refractive index. It has been suggested that the fisheye makes a perfect lens without negative refraction [Leonhardt, Philbin arxiv:0805.4778v2]. However, we point out that the definition of super-resolution in such a heterogeneous medium should be computed with respect to the wavelength in a homogenised medium, and it is perhaps more adequate to talk about a conjugate image rather than a perfect image (the former does not necessarily contain the evanescent components of the source). We numerically find that both the Maxwell fisheye and a thick silver slab lens lead to a resolution close to λ/3 in transverse magnetic polarisation (electric field pointing orthogonal to the plane). We note a shift of the image plane in the latter lens. We also observe that two sources lead to multiple secondary images in the former lens, as confirmed from light rays travelling along geodesics of the virtual sphere. We further observe resolutions ranging from λ/2 to nearly λ/4 for magnetic dipoles of varying orientations of dipole moments within the fisheye in transverse electric polarisation (magnetic field pointing orthogonal to the plane). Finally, we analyse the Eaton lens for which the source and its image are either located within a unit

  17. EDITORIAL: Focus on Cloaking and Transformation Optics

    Science.gov (United States)

    Leonhardt, Ulf; Smith, David R.

    2008-11-01

    coordinate transformations. If the coordinates they conjure up run backwards one gets negative refraction, if they exclude some region of space one makes anything inside invisible [4]. In physics, general relativity has honed the theoretical tools for understanding curved space and curved-coordinate transformations. In transformation optics, general relativity has become a theoretical tool for solving practical engineering problems [4]. What an unorthodox connection! This focus issue represents a snapshot of this rapidly developing research area. It is not restricted to optics or electromagnetism, though. Metamaterials for acoustics also exist and can be applied in ways similar to optical metamaterials. So transformation optics not only attracts an unusual mix of scientists, but also spans a range of applications in optics and beyond. Transformation optics has the potential to transform optics, for example by visualizing invisibility and making materials beyond materials—metamaterials. But before we transgress the boundaries to the hermeneutics of transformation optics [5], let the papers speak for themselves. References [1] Yao J, Liu Z, Liu Y, Wang Y, Sun C, Bartal G, Stacy A M and Zhang X 2008 Science 321 930 [2] Valentine J, Zhang S, Zentgraf T, Ulin-Avila E, Genov D A, Bartal G and Zhang X 2008 Nature 455 376 [3] Schurig D, Mock J J, Justice B J, Cummer S A, Pendry J B, Starr A F and Smith D R 2006 Science 314 977 [4] Leonhardt U and Philbin T G 2006 New J. Phys. 8 247 [5] Sokal A D 1996 Social Text 14(46/47) 217 Focus on Cloaking and Transformation Optics Contents Transformation optics for the full dielectric electromagnetic cloak and metal-dielectric planar hyperlens D P Gaillot, C Croënne, F Zhang and D Lippens Transmutation of singularities in optical instruments Tomáš Tyc and Ulf Leonhardt Electromagnetic cloaking with canonical spiral inclusions K Guven, E Saenz, R Gonzalo, E Ozbay and S Tretyakov Theory and potentials of multi-layered plasmonic covers for

  18. EDITORIAL: Focus on Heart and Mind

    Science.gov (United States)

    Bodenschatz, Eberhard; Wolf, Fred

    2008-01-01

    tractable to support a comprehensive analysis of functional performance at the systems level. Analogously, experimental work increasingly probes the system dynamics simultaneously at multiple levels from cell to whole organ. Here an invaluable contribution of physics to the experimental characterization of large scale activity in cardiac and neuronal tissues is the currently emerging high level of quantitative precision and control. Long-term high precision recording of large scale activity patterns of neural and cardiac tissues increasingly supports the formulation of quantitative phenomenological theories of complex dynamical states as well the realization of algorithms for manipulating and controlling them. Both quantitative phenomenology and control are not only essential for bridging theory and experiment in complex systems; they are also indispensable for turning scientific insight into diagnostic progress and improved treatment for the affected heart and mind. The present Focus Issue in New Journal of Physics reflects well the richness and excitement of this currently rapidly evolving field. It combines theoretical and experimental approaches and covers analyses ranging from the organ level over investigations of model systems to the biophysics of individual cells. The articles below represent the first contributions to this collection and further additions will appear in the near future. Focus on Heart and Mind Contents 'Heart' contributions Spiral wave drift and complex-oscillatory spiral waves caused by heterogeneities in two-dimensional in vitro cardiac tissues Sung-Jae Woo, Jin Hee Hong, Tae Yun Kim, Byung Wook Bae and Kyoung J Lee Epicardial wavefronts arise from widely distributed transient sources during ventricular fibrillation in the isolated swine heart J M Rogers, G P Walcott, J D Gladden, S B Melnick, R E Ideker and M W Kay Efficient control of spiral wave location in an excitable medium with localized heterogeneities J Schlesner, V S Zykov, H Brandtst

  19. Instructions to Adopt an External Focus Enhance Muscular Endurance

    Science.gov (United States)

    Marchant, David C.; Greig, Matt; Bullough, Jonathan; Hitchen, Daniel

    2011-01-01

    The influence of internal (movement focus) and external (outcome focus) attentional-focusing instructions on muscular endurance were investigated using three exercise protocols with experienced exercisers. Twenty-three participants completed a maximal repetition, assisted bench-press test on a Smith's machine. An external focus of attention…

  20. An elastic, low-background vertical focusing element for a doubly focusing neutron monochromator

    International Nuclear Information System (INIS)

    Smee, Stephen A.; Brand, Paul C.; Barry, Dwight D.; Broholm, Collin L.; Anand, Dave K.

    2001-01-01

    A novel, variable radius of curvature, device for the focusing of neutrons is presented. This elastic element consists of a thin variable thickness, constant width, aluminum blade to which diffracting crystals can be attached. When buckled, the blade assumes a circular focal shape, the radius of which is easily controlled by the relative displacement of supporting pivots. Precision electromechanical and optical measurements show that the slope of the buckled blade conforms to a circular arc to within 0.15 degree sign for radii in the range 900 mm< R<10 000 mm. This easily scalable, low mass mechanism is well suited for use in a focusing neutron monochromator, as the parasitic scattering typically associated with traditional lead screw and lever mechanisms is greatly reduced

  1. CRISPR-FOCUS: A web server for designing focused CRISPR screening experiments

    OpenAIRE

    Cao, Qingyi; Ma, Jian; Chen, Chen-Hao; Xu, Han; Chen, Zhi; Li, Wei; Liu, X. Shirley

    2017-01-01

    The recently developed CRISPR screen technology, based on the CRISPR/Cas9 genome editing system, enables genome-wide interrogation of gene functions in an efficient and cost-effective manner. Although many computational algorithms and web servers have been developed to design single-guide RNAs (sgRNAs) with high specificity and efficiency, algorithms specifically designed for conducting CRISPR screens are still lacking. Here we present CRISPR-FOCUS, a web-based platform to search and prioriti...

  2. Performances of synchrotron radiation microbeam focused by monolithic half focusing polycapillary X-ray lens

    International Nuclear Information System (INIS)

    Sun Tianxi; Liu Zhiguo; He Bo; Wei Shiqiang; Xie Yaning; Liu Tao; Hu Tiandou; Ding Xunliang

    2007-01-01

    A monolithic half focusing polycapillary X-ray lens (MHFPXRL) composed of 289,000 capillaries is used to produce a synchrotron radiation microbeam. The energy dependence of the output focal distance, focal spot size, transmission efficiency, vertical beam position, and gain in flux density of this microbeam is studied in detail. There is a slight change in the output focal distance of the MHFPXRL when the X-ray energies change

  3. Reviewing the Focus: A Summary and Critique of Child-Focused Sexual Abuse Prevention.

    Science.gov (United States)

    Rudolph, Julia; Zimmer-Gembeck, Melanie J

    2016-10-26

    Due to the high incidence, and widespread detrimental health consequences, of child sexual abuse (CSA), effective prevention remains at the forefront of public and mental health research, prevention and intervention agendas. To date much of the focus of prevention has been on school-based education programs designed to teach children skills to evade adult sexual advances, and disclose past or ongoing abuse. Evaluation of sexual abuse prevention programs demonstrate their effectiveness in increasing children's knowledge of CSA concepts and protection skills, but little is known about their effects on children's capacity to prevent abuse. Moreover, concerns persist about the unintended side-effects for young children such as anxiety, worry and wariness of touch. This paper summarizes the recent history of CSA prevention and the critique of child-focused protection programs in order to demonstrate the need to compliment or replace these programs by focusing more on protectors in the children's ecology, specifically parents, in order to create safer environments in which abuse is less likely to occur. © The Author(s) 2016.

  4. Expanded studies of linear collider final focus systems at the Final Focus Test Beam

    International Nuclear Information System (INIS)

    Tenenbaum, P.G.

    1995-12-01

    In order to meet their luminosity goals, linear colliders operating in the center-of-mass energy range from 3,50 to 1,500 GeV will need to deliver beams which are as small as a few Manometers tall, with x:y aspect ratios as large as 100. The Final Focus Test Beam (FFTB) is a prototype for the final focus demanded by these colliders: its purpose is to provide demagnification equivalent to those in the future linear collider, which corresponds to a focused spot size in the FFTB of 1.7 microns (horizontal) by 60 manometers (vertical). In order to achieve the desired spot sizes, the FFTB beam optics must be tuned to eliminate aberrations and other errors, and to ensure that the optics conform to the desired final conditions and the measured initial conditions of the beam. Using a combination of incoming-beam diagnostics. beam-based local diagnostics, and global tuning algorithms, the FFTB beam size has been reduced to a stable final size of 1.7 microns by 70 manometers. In addition, the chromatic properties of the FFTB have been studied using two techniques and found to be acceptable. Descriptions of the hardware and techniques used in these studies are presented, along with results and suggestions for future research

  5. Expanded studies of linear collider final focus systems at the Final Focus Test Beam

    Energy Technology Data Exchange (ETDEWEB)

    Tenenbaum, Peter Gregory [Stanford Univ., CA (United States)

    1995-12-01

    In order to meet their luminosity goals, linear colliders operating in the center-of-mass energy range from 3,50 to 1,500 GeV will need to deliver beams which are as small as a few Manometers tall, with x:y aspect ratios as large as 100. The Final Focus Test Beam (FFTB) is a prototype for the final focus demanded by these colliders: its purpose is to provide demagnification equivalent to those in the future linear collider, which corresponds to a focused spot size in the FFTB of 1.7 microns (horizontal) by 60 manometers (vertical). In order to achieve the desired spot sizes, the FFTB beam optics must be tuned to eliminate aberrations and other errors, and to ensure that the optics conform to the desired final conditions and the measured initial conditions of the beam. Using a combination of incoming-beam diagnostics. beam-based local diagnostics, and global tuning algorithms, the FFTB beam size has been reduced to a stable final size of 1.7 microns by 70 manometers. In addition, the chromatic properties of the FFTB have been studied using two techniques and found to be acceptable. Descriptions of the hardware and techniques used in these studies are presented, along with results and suggestions for future research.

  6. Nonlinear focal shift beyond the geometrical focus in moderately focused acoustic beams.

    Science.gov (United States)

    Camarena, Francisco; Adrián-Martínez, Silvia; Jiménez, Noé; Sánchez-Morcillo, Víctor

    2013-08-01

    The phenomenon of the displacement of the position along the axis of the pressure, intensity, and radiation force maxima of focused acoustic beams under increasing driving voltages (nonlinear focal shift) is studied for the case of a moderately focused beam. The theoretical and experimental results show the existence of this shift along the axis when the initial pressure in the transducer increases until the acoustic field reaches the fully developed nonlinear regime of propagation. Experimental data show that at high amplitudes and for moderate focusing, the position of the on-axis pressure maximum and radiation force maximum can surpass the geometrical focal length. On the contrary, the on-axis pressure minimum approaches the transducer under increasing driving voltages, increasing the distance between the positive and negative peak pressure in the beam. These results are in agreement with numerical KZK model predictions and the existed data of other authors and can be explained according to the effect of self-refraction characteristic of the nonlinear regime of propagation.

  7. Focus groups: a useful tool for curriculum evaluation.

    Science.gov (United States)

    Frasier, P Y; Slatt, L; Kowlowitz, V; Kollisch, D O; Mintzer, M

    1997-01-01

    Focus group interviews have been used extensively in health services program planning, health education, and curriculum planning. However, with the exception of a few reports describing the use of focus groups for a basic science course evaluation and a clerkship's impact on medical students, the potential of focus groups as a tool for curriculum evaluation has not been explored. Focus groups are a valid stand-alone evaluation process, but they are most often used in combination with other quantitative and qualitative methods. Focus groups rely heavily on group interaction, combining elements of individual interviews and participant observation. This article compares the focus group interview with both quantitative and qualitative methods; discusses when to use focus group interviews; outlines a protocol for conducting focus groups, including a comparison of various styles of qualitative data analysis; and offers a case study, in which focus groups evaluated the effectiveness of a pilot preclinical curriculum.

  8. Focusing on butterfly eyespot focus: uncoupling of white spots from eyespot bodies in nymphalid butterflies.

    Science.gov (United States)

    Iwata, Masaki; Otaki, Joji M

    2016-01-01

    Developmental studies on butterfly wing color patterns often focus on eyespots. A typical eyespot (such as that of Bicyclus anynana) has a few concentric rings of dark and light colors and a white spot (called a focus) at the center. The prospective eyespot center during the early pupal stage is known to act as an organizing center. It has often been assumed, according to gradient models for positional information, that a white spot in adult wings corresponds to an organizing center and that the size of the white spot indicates how active that organizing center was. However, there is no supporting evidence for these assumptions. To evaluate the feasibility of these assumptions in nymphalid butterflies, we studied the unique color patterns of Calisto tasajera (Nymphalidae, Satyrinae), which have not been analyzed before in the literature. In the anterior forewing, one white spot was located at the center of an eyespot, but another white spot associated with either no or only a small eyespot was present in the adjacent compartment. The anterior hindwing contained two adjacent white spots not associated with eyespots, one of which showed a sparse pattern. The posterior hindwing contained two adjacent pear-shaped eyespots, and the white spots were located at the proximal side or even outside the eyespot bodies. The successive white spots within a single compartment along the midline in the posterior hindwing showed a possible trajectory of a positional determination process for the white spots. Several cases of focus-less eyespots in other nymphalid butterflies were also presented. These results argue for the uncoupling of white spots from eyespot bodies, suggesting that an eyespot organizing center does not necessarily differentiate into a white spot and that a prospective white spot does not necessarily signify organizing activity for an eyespot. Incorporation of these results in future models for butterfly wing color pattern formation is encouraged.

  9. Five focus strategies to organize health care delivery.

    Science.gov (United States)

    Peltokorpi, Antti; Linna, Miika; Malmström, Tomi; Torkki, Paulus; Lillrank, Paul Martin

    2016-01-01

    The focused factory is one of the concepts that decision-makers have adopted for improving health care delivery. However, disorganized definitions of focus have led to findings that cannot be utilized systematically. The purpose of this paper is to discuss strategic options to focus health care operations. First the literature on focus in health care is reviewed revealing conceptual challenges. Second, a definition of focus in terms of demand and requisite variety is defined, and the mechanisms of focus are explicated. A classification of five focus strategies that follow the original idea to reduce variety in products and markets is presented. Finally, the paper examines managerial possibilities linked to the focus strategies. The paper proposes a framework of five customer-oriented focus strategies which aim at reducing variety in different characteristics of care pathways: population; urgency and severity; illnesses and symptoms; care practices and processes; and care outcomes. Empirical research is needed to evaluate the costs and benefits of the five strategies and about system-level effects of focused units on competition and coordination. Focus is an enabling condition that needs to be exploited using specific demand and supply management practices. It is essential to understand how focus mechanisms differ between strategies, and to select focus that fits with organization's strategy and key performance indicators. Compared to previous more resource-oriented approaches, this study provides theoretically solid and practically relevant customer-oriented framework for focusing in health care.

  10. The Focus of Attention in Visual Working Memory: Protection of Focused Representations and Its Individual Variation.

    Science.gov (United States)

    Heuer, Anna; Schubö, Anna

    2016-01-01

    Visual working memory can be modulated according to changes in the cued task relevance of maintained items. Here, we investigated the mechanisms underlying this modulation. In particular, we studied the consequences of attentional selection for selected and unselected items, and the role of individual differences in the efficiency with which attention is deployed. To this end, performance in a visual working memory task as well as the CDA/SPCN and the N2pc, ERP components associated with visual working memory and attentional processes, were analysed. Selection during the maintenance stage was manipulated by means of two successively presented retrocues providing spatial information as to which items were most likely to be tested. Results show that attentional selection serves to robustly protect relevant representations in the focus of attention while unselected representations which may become relevant again still remain available. Individuals with larger retrocueing benefits showed higher efficiency of attentional selection, as indicated by the N2pc, and showed stronger maintenance-associated activity (CDA/SPCN). The findings add to converging evidence that focused representations are protected, and highlight the flexibility of visual working memory, in which information can be weighted according its relevance.

  11. PREFACE: Focus section on superconducting power systems Focus section on superconducting power systems

    Science.gov (United States)

    Cardwell, D. A.; Amemiya, N.; Fair, R.

    2012-01-01

    This focus section of Superconductor Science and Technology looks at the properties, technology and applications of (RE)BCO and MgB2 based superconductors for power engineering systems. Both bulk and conductor forms of material are addressed, including elements of materials fabrication and processing, and the measurement of their applied properties for various levels of system application. The areas of research include ac losses in type II materials in power devices, cables and coated conductors, the development of high current dc cables and the application of superconductors in levitation devices, motors and fault current limiters. This focus section presents a broad cross-section of contemporary issues, that represent state-of-the-art for power applications of superconductors, and highlights the areas that require further development if commercial applications of these rapidly emerging materials are to be realised. It contains papers from some of the major groups in the field, including contributions from Europe, the USA and Japan, and describes devices that are relatively close to market.

  12. Toric focusing for radiation force applications using a toric lens coupled to a spherically focused transducer.

    Science.gov (United States)

    Arnal, Bastien; Nguyen, Thu-Mai; O'Donnell, Matthew

    2014-12-01

    Dynamic elastography using radiation force requires that an ultrasound field be focused during hundreds of microseconds at a pressure of several megapascals. Here, we address the importance of the focal geometry. Although there is usually no control of the elevational focal width in generating a tissue mechanical response, we propose a tunable approach to adapt the focus geometry that can significantly improve radiation force efficiency. Several thin, in-house-made polydimethylsiloxane lenses were designed to modify the focal spot of a spherical transducer. They exhibited low absorption and the focal spot widths were extended up to 8-fold in the elevation direction. Radiation force experiments demonstrated an 8-fold increase in tissue displacements using the same pressure level in a tissue-mimicking phantom with a similar shear wave spectrum, meaning it does not affect elastography resolution. Our results demonstrate that larger tissue responses can be obtained for a given pressure level, or that similar response can be reached at a much lower mechanical index (MI). We envision that this work will impact 3-D elastography using 2-D phased arrays, where such shaping can be achieved electronically with the potential for adaptive optimization.

  13. Employees' Assessment Of Customer Focus In A Tertiary Hospital In ...

    African Journals Online (AJOL)

    Employees' Assessment Of Customer Focus In A Tertiary Hospital In ... tool 'Are we making progress?' were used by respondents to rate customer focus. ... that they were allowed to take decisions to solve problems for customers (p < 0.001).

  14. The Relationship Between Personality Type And Leadership Focus

    Directory of Open Access Journals (Sweden)

    Grant Sieff

    2006-11-01

    Full Text Available Optimising focus is a key success driver for many organisation leaders. The relationship between personality type and leadership focus is examined. Personality type is assessed with Form M of the Myers-Briggs Type Indicator instrument, and leadership focus is explored through the development and application of a Leadership Focus Questionnaire. South African executives form the target population for this study. Both functionalist and interpretive approaches are applied. Three primary theoretical hypotheses about leadership focus, concerning (1 optimising the balance of focus between external and internal priorities, (2 the fit between the leadership personality type and the organisation type, and (3 the capacity to manage a multiple focus, are considered. Results show that Extraverted personality types are more comfortable with the challenges of focus in the leadership role than are Introverted types, and Extraverted, Sensing, Thinking and Judging types experience a greater degree of fit with their organisations than do Introverted, Intuitive, Feeling and Perceiving types.

  15. Self-focusing relativistic electron streams in plasmas

    International Nuclear Information System (INIS)

    Cox, J.L. Jr.

    1975-01-01

    A relativistic electron stream propagating through a dense plasma induces current and charge densities which determine how the stream can self-focus. Magnetic self-focusing is possible because stream-current neutralization, although extensive, is not complete. Electric self-focusing can occur because the stream charge becomes overneutralized when the net current is smaller than a critical value. Under some circumstances, the latter process can cause the stream to focus into a series of electron bunches

  16. CFP (Common Focus Point) redatuming: cinematic approach; Redatumacao CFP (Common Focus Point): uma abordagem cinematica

    Energy Technology Data Exchange (ETDEWEB)

    Filgueiras, Erica C.C.S.; Santoro, Marcus V.L. [Halliburton Servicos Ltda., Rio de Janeiro, RJ (Brazil); Silva, Josias J. [Universidade Federal do Rio de Janeiro (UFRJ), RJ (Brazil). Coordenacao dos Programas de Pos-graduacao de Engenharia (COPPE); Jesus, Carlos A.C. [Universidade Federal Fluminense (UFF), Niteroi, RJ (Brazil)

    2008-07-01

    The quality of seismic data can be degrade by effects originated from a complex near surface, like the presence of canyons in marine floor. Filgueiras (2007) introduced a new formulation for data recorded redatuming on surface that are influenced by canyons present in marine floor, using the concept of Common Focus Point (CFP) Gather, with wave field extrapolations without asymptotic approximations. This new formulation proposes to eliminate the effects of the floor marine topography (Filgueiras, 2007). It is based on the concepts of CFP technology introduced by Berkhout (1997 a. and 1997 b.) and the virtual source method, introduced by Bakulin and Calvert (2004). This procedure implies a new datum a final seismogram redatuming, capable to show the reflections with no canyons influence of the most all reflectors that are under the reference datum. From cinematic point at view, the results from synthetic data were satisfied. (author)

  17. PREFACE: Focus section on Hadronic Physics Focus section on Hadronic Physics

    Science.gov (United States)

    Roberts, Craig; Swanson, Eric

    2007-07-01

    Hadronic physics is the study of strongly interacting matter and its underlying theory, Quantum Chromodynamics (QCD). The field had its beginnings after World War Two, when hadrons were discovered in ever increasing numbers. Today, it encompasses topics like the quark-gluon structure of hadrons at varying scales, the quark-gluon plasma and hadronic matter at extreme temperature and density; it also underpins nuclear physics and has significant impact on particle physics, astrophysics, and cosmology. Among the goals of hadronic physics are to determine the parameters of QCD, understand the origin and characteristics of confinement, understand the dynamics and consequences of dynamical chiral symmetry breaking, explore the role of quarks and gluons in nuclei and in matter under extreme conditions and understand the quark and gluon structure of hadrons. In general, the process is one of discerning the relevant degrees of freedom and relating these to the fundamental fields of QCD. The emphasis is on understanding QCD, rather than testing it. The papers gathered in this special focus section of Journal of Physics G: Nuclear and Particle Physics attempt to cover this broad range of subjects. Alkofer and Greensite examine the issue of quark and gluon confinement with the focus on models of the QCD vacuum, lattice gauge theory investigations, and the relationship to the AdS/CFT correspondence postulate. Arrington et al. review nucleon form factors and their role in determining quark orbital momentum, the strangeness content of the nucleon, meson cloud effects, and the transition from nonperturbative to perturbative QCD dynamics. The physics associated with hadronic matter at high temperature and density and at low Bjorken-x at the Relativistic Heavy Ion Collider (RHIC), the SPS at CERN, and at the future LHC is summarized by d'Enterria. The article of Lee and Smith examines experiment and theory associated with electromagnetic meson production from nucleons and

  18. Self-focusing of laser beam crossing a laser plasma

    International Nuclear Information System (INIS)

    Bakos, J.S.; Foeldes, I.B.; Ignacz, P.N.; Soerlei, Zs.

    1983-03-01

    A crossed-beam experiment was performed to clarify the mechanism of self-focusing in a laser produced spark. The plasma was created by one beam and self-focusing was observed in the weak probe beam which crossed the plasma. Experimental results show that the cause of self-focusing is the nonuniform heating mechanism. (author)

  19. Focus on Student Success: Components for Effective Summer Bridge Programs

    Science.gov (United States)

    Gonzalez Quiroz, Alicia; Garza, Nora R.

    2018-01-01

    Using research focused on best practices, focus group information, and data analytics, the Title V: Focus on Student Success (FOSS) Grant created a model for the development, implementation, and evaluation of a summer bridge program. Results included increased academic performance indicators in first-year Hispanic college students. Validation for…

  20. Focus Group Evidence: Implications for Design and Analysis

    Science.gov (United States)

    Ryan, Katherine E.; Gandha, Tysza; Culbertson, Michael J.; Carlson, Crystal

    2014-01-01

    In evaluation and applied social research, focus groups may be used to gather different kinds of evidence (e.g., opinion, tacit knowledge). In this article, we argue that making focus group design choices explicitly in relation to the type of evidence required would enhance the empirical value and rigor associated with focus group utilization. We…

  1. Health care providers' knowledge and practice of focused antenatal ...

    African Journals Online (AJOL)

    ... observational checklist were the instruments for data collection. Findings revealed poor knowledge of concept, components, timing of visits on focused antenatal care and non compliance with the guidelines for the practice of focused antenatal care, because of health workers lack of knowledge on focused antenatal care.

  2. Assessment of Working Scientifically--The TAPS Focused Assessment Approach

    Science.gov (United States)

    McMahon, Kendra

    2018-01-01

    The Teacher Assessment in Primary Science (TAPS) Focused Assessment approach embeds assessment within normal classroom science activities. Essentially, a Focused Assessment is a lesson plan for a science inquiry, with an identified focus for assessment and guidance on how to interpret the children's responses in relation to expectations for that…

  3. A Feminist Critique of Solution-Focused Therapy.

    Science.gov (United States)

    Dermer, Shannon B.; Hemesath, Crystal Wilhite; Russell, Candyce S.

    1998-01-01

    Applying the feminist critique to solution-focused therapy highlights the strengths and weaknesses of this model from a feminist perspective. Although solution-focused therapy and feminist approaches share an emphasis on competence and strengths, solution-focused theory tends to overlook gender and power differences. In general, the model falls…

  4. Self-focusing Past and Present - Fundamentals and Prospects

    CERN Document Server

    Boyd, Robert W

    2007-01-01

    Self-focusing has been an area of active scientific investigation for years. From a practical point of view, self-focusing effects impose a limit on the power that can be transmitted through a material medium. This book presents a comprehensive treatment of this topic and reviews both theoretical and experimental investigations of self-focusing.

  5. Focus on Form in task-based language teaching

    NARCIS (Netherlands)

    van de Guchte, M.

    2015-01-01

    This dissertation presents research on the way in which learners focus on grammar in task-based language teaching (TBLT). Such a focus on grammar during meaningful task performance is called a Focus on Form (FonF). For this PhD research project we conducted three experimental studies which

  6. Design of High Precise Focusing System in Laser Direct Writer

    International Nuclear Information System (INIS)

    Liang, Y Y; Tian, F; Luo, J B; Yang, G G

    2006-01-01

    In order to improve the accuracy and efficiency of fabricating lines with laser pattern generator, a novel focusing system was designed. Focusing system is based on optical off-axis detection principle. The detector is a two-quadrant photocell and the defocus signal is constructed by division. Focusing system has the character of second-order system with overdamp. The new embedded PID controller improves the performance of focusing system and upgrades the closed-loop precision to 0.2 μm. Furthermore focusing system has the fabrication capabilities for alterable-width lines under various defocus amount

  7. Broadband and flexible acoustic focusing by metafiber bundles

    Science.gov (United States)

    Sun, Hong-Xiang; Chen, Jia-He; Ge, Yong; Yuan, Shou-Qi; Liu, Xiao-Jun

    2018-06-01

    We report a broadband and flexible acoustic focusing through metafiber bundles in air, in which each metafiber consists of eight circular and narrow rectangular cavities. The fractional bandwidth of the acoustic focusing could reach about 0.2, which arises from the eigenmodes of the metafiber structure. Besides, owing to the flexible characteristic of the metafibers, the focus position can be manipulated by bending the metafiber bundles, and the metafiber bundles could bypass rigid scatterers inside the lens structure. More interestingly, the acoustic propagation and focusing directions can be changed by using a designed right-angled direction converter fabricated by the metafibers, and a waveform converter and a focusing lens of the cylindrical acoustic source are realized based on the metafiber bundles. The proposed focusing lens has the advantages of broad bandwidth, flexible structure, and high focusing performance, showing great potentials in versatile applications.

  8. Development of the FOCUS (Focus on the Outcomes of Communication under Six), a Communication Outcome Measure for Preschool Children

    Science.gov (United States)

    Thomas-Stonell, Nancy L.; Oddson, Bruce; Robertson, Bernadette; Rosenbaum, Peter L.

    2010-01-01

    Aim: Our aim was to develop an outcome measure, called Focus on the Outcomes of Communication Under Six (FOCUS), that captures real-world changes in preschool children's communication. Conceptually grounded in the World Health Organization International Classification of Functioning, Disability and Health framework, the FOCUS items were derived…

  9. Stay Focused! The Effects of Internal and External Focus of Attention on Movement Automaticity in Patients with Stroke

    Science.gov (United States)

    Kal, E. C.; van der Kamp, J.; Houdijk, H.; Groet, E.; van Bennekom, C. A. M.; Scherder, E. J. A.

    2015-01-01

    Dual-task performance is often impaired after stroke. This may be resolved by enhancing patients’ automaticity of movement. This study sets out to test the constrained action hypothesis, which holds that automaticity of movement is enhanced by triggering an external focus (on movement effects), rather than an internal focus (on movement execution). Thirty-nine individuals with chronic, unilateral stroke performed a one-leg-stepping task with both legs in single- and dual-task conditions. Attentional focus was manipulated with instructions. Motor performance (movement speed), movement automaticity (fluency of movement), and dual-task performance (dual-task costs) were assessed. The effects of focus on movement speed, single- and dual-task movement fluency, and dual-task costs were analysed with generalized estimating equations. Results showed that, overall, single-task performance was unaffected by focus (p = .341). Regarding movement fluency, no main effects of focus were found in single- or dual-task conditions (p’s ≥ .13). However, focus by leg interactions suggested that an external focus reduced movement fluency of the paretic leg compared to an internal focus (single-task conditions: p = .068; dual-task conditions: p = .084). An external focus also tended to result in inferior dual-task performance (β = -2.38, p = .065). Finally, a near-significant interaction (β = 2.36, p = .055) suggested that dual-task performance was more constrained by patients’ attentional capacity in external focus conditions. We conclude that, compared to an internal focus, an external focus did not result in more automated movements in chronic stroke patients. Contrary to expectations, trends were found for enhanced automaticity with an internal focus. These findings might be due to patients’ strong preference to use an internal focus in daily life. Future work needs to establish the more permanent effects of learning with different attentional foci on re-automating motor

  10. Stay Focused! The Effects of Internal and External Focus of Attention on Movement Automaticity in Patients with Stroke.

    Science.gov (United States)

    Kal, E C; van der Kamp, J; Houdijk, H; Groet, E; van Bennekom, C A M; Scherder, E J A

    2015-01-01

    Dual-task performance is often impaired after stroke. This may be resolved by enhancing patients' automaticity of movement. This study sets out to test the constrained action hypothesis, which holds that automaticity of movement is enhanced by triggering an external focus (on movement effects), rather than an internal focus (on movement execution). Thirty-nine individuals with chronic, unilateral stroke performed a one-leg-stepping task with both legs in single- and dual-task conditions. Attentional focus was manipulated with instructions. Motor performance (movement speed), movement automaticity (fluency of movement), and dual-task performance (dual-task costs) were assessed. The effects of focus on movement speed, single- and dual-task movement fluency, and dual-task costs were analysed with generalized estimating equations. Results showed that, overall, single-task performance was unaffected by focus (p = .341). Regarding movement fluency, no main effects of focus were found in single- or dual-task conditions (p's ≥ .13). However, focus by leg interactions suggested that an external focus reduced movement fluency of the paretic leg compared to an internal focus (single-task conditions: p = .068; dual-task conditions: p = .084). An external focus also tended to result in inferior dual-task performance (β = -2.38, p = .065). Finally, a near-significant interaction (β = 2.36, p = .055) suggested that dual-task performance was more constrained by patients' attentional capacity in external focus conditions. We conclude that, compared to an internal focus, an external focus did not result in more automated movements in chronic stroke patients. Contrary to expectations, trends were found for enhanced automaticity with an internal focus. These findings might be due to patients' strong preference to use an internal focus in daily life. Future work needs to establish the more permanent effects of learning with different attentional foci on re-automating motor control

  11. EDITORIAL: Focus on Micro- and Nanofluidics FOCUS ON MICRO- AND NANOFLUIDICS

    Science.gov (United States)

    Ajdari, Armand; Stone, Howard A.

    2009-07-01

    This focus issue of New Journal of Physics concentrates on recent developments in microfluidics, and related small-scale flow themes. This subject touches on many areas with the common element that they are engaged with understanding, measuring or manipulating flows at the scale of a few hundred microns or smaller. Microfluidics is of interest to many scientists and engineers from many disciplines because it is a toolbox from which they can investigate basic questions in their respective fields. In particular, the field has led to new studies of small-scale fluid flows, especially those dominated by surface effects, which is crucial for understanding electrokinetics, chemical reactions and phase changes, and multiphase systems, including those involving dispersed liquid and gas phases, suspended particles, cells, vesicles, capsules, etc. The lower length scale of these kinds of flows concerns nanoscale manipulation of objects such as DNA or nanoparticles, nanofabrication of surfaces, studies of the flow within nanometers of substrates, etc. Microfluidics has also given rise to technologies because it enables design and implementation of new devices for sensing, detection, measurement, materials characterization, combinatorial discovery, cellular-scale manipulation, miniaturization of reactors, etc. The fact that these systems are small, cheap, physically flexible, portable, multifunctional, and, when they are working, produce measurements quickly, offers many new avenues for innovation. In this issue we highlight contributions from around the world that explore research directions inspired by the manifold possibilities of microfluidics. In particular, the papers include reports of single-phase flows that are driven by electrical fields, so-called electrokinetics. Although the field has its origins in the 19th century, if not even earlier, new theoretical ideas are required to understand dynamics close to charged surfaces, and new applications of the basic ideas are

  12. NATIVE LANGUAGE INFLUENCE IN LEARNERS'. ASSESSMENT OF ENGLISH FOCUS

    Directory of Open Access Journals (Sweden)

    M. L. Garcia Lecumberri

    2001-06-01

    Full Text Available Accentual focus is a frequent linguistic device in English which may also be used in Spanish but less widely and less frequently. Given this disparity, it was expected that native language influence would manifest itself in FL leamers' focus assessrnents as cornpared to native English speakers. Other factors were also expected to account of listener perceptions, such as task type and linguistic competence. Two focus domains were used to test hypotheses: utterance initial and utterance medial focus. Focus identification was tested using two tasks which differed in their cognitive demands: multiple choice and open questions. Acceptability was estirnated by asking listeners to rate utterances on a five point scale. English NL listeners displayed better focus identification rates as cornpared to FL learners. This result may be understood both as an effect of native competence advantage and also as a reflection of native language influence. Both listener groups found utterance initial focus easier to identi@ and considered it to be more acceptable than medial focus. Both groups showed worse results in the open test, which is interpreted as a consequence of this task being more demanding on listeners' explicit knowledge. These trends were much more pronounced amongst FL leamers. It is suggested that the potential ambiguity of English medial focus is partly responsible for the bias against it. Additionally, Spanish listeners results show the their NL influence in this bias as well as in the good results for initial focus and acceptability estirnations.

  13. EDITORIAL: Focus on Cold and Ultracold Molecules FOCUS ON COLD AND ULTRACOLD MOLECULES

    Science.gov (United States)

    Carr, Lincoln D.; Ye, Jun

    2009-05-01

    Cold and ultracold molecules are the next wave of ultracold physics, giving rise to an exciting array of scientific opportunities, including many body physics for novel quantum phase transitions, new states of matter, and quantum information processing. Precision tests of fundamental physical laws benefit from the existence of molecular internal structure with exquisite control. The study of novel collision and reaction dynamics will open a new chapter of quantum chemistry. Cold molecules bring together researchers from a variety of fields, including atomic, molecular, and optical physics, chemistry and chemical physics, quantum information science and quantum simulations, condensed matter physics, nuclear physics, and astrophysics, a truly remarkable synergy of scientific explorations. For the past decade there have been steady advances in direct cooling techniques, from buffer-gas cooling to cold molecular beams to electro- and magneto-molecular decelerators. These techniques have allowed a large variety of molecules to be cooled for pioneering studies. Recent amazing advances in experimental techniques combining the ultracold and the ultraprecise have furthermore brought molecules to the point of quantum degeneracy. These latter indirect cooling techniques magnetically associate atoms from a Bose-Einstein condensate and/or a quantum degenerate Fermi gas, transferring at 90% efficiency highly excited Fano-Feshbach molecules, which are on the order of 10 000 Bohr radii in size, to absolute ground state molecules just a few Bohr across. It was this latter advance, together with significant breakthroughs in internal state manipulations, which inspired us to coordinate this focus issue now, and is the reason why we say the next wave of ultracold physics has now arrived. Whether directly or indirectly cooled, heteronuclear polar molecules offer distinct new features in comparison to cold atoms, while sharing all of their advantages (purity, high coherence

  14. Electrostatic focusing of directly heated linear filament gun using EGUN

    International Nuclear Information System (INIS)

    Iqbal, Munawar; Lodhi, M.A.K.; Majeed, Zahid; Batani, Dimitri

    2011-01-01

    This paper presents the optimization of a line source rectangular electron gun using electrostatic focusing. We optimized the gun by shaping the configuration of its electrodes in order to achieve the desired focusing characteristics, namely maximum focusing distance and minimum beam spread. The optimization has been carried out using the software EGUN. We have also simplified the gun design using only one focusing electrode at the same potential as that of the cathode and by avoiding magnetic focusing field, separate focusing electrodes and additional power supply, thus minimizing the cost without any loss in its accuracy and efficient performance. This gun with the optimum configuration was used in actual experiment and the results of the simulation were compared with the experimental measurements.

  15. Electrostatic focusing of directly heated linear filament gun using EGUN

    Energy Technology Data Exchange (ETDEWEB)

    Iqbal, Munawar, E-mail: muniqbal@yahoo.com [Department of Physics, Texas Tech University, Lubbock, TX 79409 (United States); Lodhi, M.A.K. [Department of Physics, Texas Tech University, Lubbock, TX 79409 (United States); Majeed, Zahid [National Engineering and Science Commission, Islamabad (Pakistan); Batani, Dimitri [Dipartimento di Fisica, Universita degli Studi di Milano Bicocca (Italy)

    2011-06-11

    This paper presents the optimization of a line source rectangular electron gun using electrostatic focusing. We optimized the gun by shaping the configuration of its electrodes in order to achieve the desired focusing characteristics, namely maximum focusing distance and minimum beam spread. The optimization has been carried out using the software EGUN. We have also simplified the gun design using only one focusing electrode at the same potential as that of the cathode and by avoiding magnetic focusing field, separate focusing electrodes and additional power supply, thus minimizing the cost without any loss in its accuracy and efficient performance. This gun with the optimum configuration was used in actual experiment and the results of the simulation were compared with the experimental measurements.

  16. Electrostatic focusing of directly heated linear filament gun using EGUN

    Science.gov (United States)

    Iqbal, Munawar; Lodhi, M. A. K.; Majeed, Zahid; Batani, Dimitri

    2011-06-01

    This paper presents the optimization of a line source rectangular electron gun using electrostatic focusing. We optimized the gun by shaping the configuration of its electrodes in order to achieve the desired focusing characteristics, namely maximum focusing distance and minimum beam spread. The optimization has been carried out using the software EGUN. We have also simplified the gun design using only one focusing electrode at the same potential as that of the cathode and by avoiding magnetic focusing field, separate focusing electrodes and additional power supply, thus minimizing the cost without any loss in its accuracy and efficient performance. This gun with the optimum configuration was used in actual experiment and the results of the simulation were compared with the experimental measurements.

  17. Characteristics and Applications of Spatiotemporally Focused Femtosecond Laser Pulses

    Directory of Open Access Journals (Sweden)

    Chenrui Jing

    2016-12-01

    Full Text Available Simultaneous spatial and temporal focusing (SSTF of femtosecond laser pulses gives rise to strong suppression of nonlinear self-focusing during the propagation of the femtosecond laser beam. In this paper, we begin with an introduction of the principle of SSTF, followed by a review of our recent experimental results on the characterization and application of the spatiotemporally focused pulses for femtosecond laser micromachining. Finally, we summarize all of the results and give a future perspective of this technique.

  18. BDNF, impulsiveness and avoidant focused coping in suicide attempters

    OpenAIRE

    AMBRUS, LIVIA

    2016-01-01

    Brain-derived neurotrophic factor (BDNF) is an important protein for neuroplasticity and neurogenesis. In this thesis the role of BDNF, in suicidal behaviour was investigated with focus on possible risk factors for suicidal behaviour such as avoidant focused coping, dysfuntional personality traits like impulsiveness and hyperactivity of the Hypothalamic-Pituitary-Adrenal (HPA) axis.Paper I: The association between avoidant focused coping and the BDNF Val66Met gene polymorphism in two differen...

  19. Aerodynamic focusing of particles and heavy molecules: First annual report

    International Nuclear Information System (INIS)

    de la Mora, J.F.

    1988-01-01

    Our first goal was to investigate the phenomenon of aerodynamic focusing in supersonic free jets, in order to assess its potential technological uses in /open quotes/direct writing/close quotes/ and other energy-related applications. Our research program divides itself naturally into two chapters: on focusing microscopic particles, and on focusing individual molecules of heavy vapors carried in jets of He and H 2 . In both lines we combine diverse experimental and theoretical methods of attack. 3 refs., 4 figs

  20. Adaptive photoacoustic imaging using the Mallart-Fink focusing factor

    Science.gov (United States)

    Li, Meng-Lin

    2008-02-01

    Focusing errors caused by sound velocity heterogeneities widen the mainlobe and elevate the sidelobes, thus degrading both spatial and contrast resolutions in photoacoustic imaging. We propose an adaptive array-based photoacoustic imaging technique that uses the Mallart-Fink (MF) focusing factor weighting to reduce the effect of such focusing errors. The definition of the MF focusing factor indicates that the MF focusing factor at the main lobe of the point-spread function is high (close to 1, without speckle noise being present, which is the case in photoacoustic imaging), whereas it is low at the sidelobes. Based on this property, the elevated sidelobes caused by sound velocity heterogeneities in the tissue can be suppressed after being multiplied by the corresponding map of the MF focusing factor on each imaging point; thus the focusing quality can be improved. This technique makes no assumption of sources of focusing errors and directly suppresses the unwanted sidelobe contributions. Numerical experiments with near field phase screen and displaced phase screen models were performed here to verify the proposed adaptive weighting technique. The effect of the signal-to-noise ratio on the MF focusing factor is also discussed.

  1. HINS Linac front end focusing system R&D

    Energy Technology Data Exchange (ETDEWEB)

    Apollinari, G.; Carcagno, R.H.; Dimarco, J.; Huang, Y.; Kashikhin, V.V.; Orris, D.F.; Page, T.M.; Rabehl, R.; Sylvester, C.; Tartaglia, M.A.; Terechkine, I.; /Fermilab /Argonne

    2008-08-01

    This report summarizes current status of an R&D program to develop a focusing system for the front end of a superconducting RF linac. Superconducting solenoids will be used as focusing lenses in the low energy accelerating sections of the front end. The development of focusing lenses for the first accelerating section is in the production stage, and lens certification activities are in preparation at FNAL. The report contains information about the focusing lens design and performance, including solenoid, dipole corrector, and power leads, and about cryogenic system design and performance. It also describes the lens magnetic axis position measurement technique and discusses scope of an acceptance/certification process.

  2. HINS Linac front end focusing system R and D

    International Nuclear Information System (INIS)

    Apollinari, G.; Carcagno, R.H.; Dimarco, J.; Huang, Y.; Kashikhin, V.V.; Orris, D.F.; Page, T.M.; Rabehl, R.; Sylvester, C.; Tartaglia, M.A.; Terechkine, I.; Fermilab; Argonne

    2008-01-01

    This report summarizes current status of an R and D program to develop a focusing system for the front end of a superconducting RF linac. Superconducting solenoids will be used as focusing lenses in the low energy accelerating sections of the front end. The development of focusing lenses for the first accelerating section is in the production stage, and lens certification activities are in preparation at FNAL. The report contains information about the focusing lens design and performance, including solenoid, dipole corrector, and power leads, and about cryogenic system design and performance. It also describes the lens magnetic axis position measurement technique and discusses scope of an acceptance/certification process

  3. Investigation of a staged plasma-focus apparatus

    International Nuclear Information System (INIS)

    Lee, J.H.; McFarland, D.R.; Harries, W.L.

    1978-01-01

    A new staged plasma-focus geometry combining two Mather-type plasma-focus guns has been constructed, and the current-sheet dynamics investigated. The production of simultaneous pairs of plasma foci has been achieved. The intensities of X-ray and fusion-neutron emission were measured and found to agree with the scaling law for a plasma focus. Advantages of this new geometry include the possibility of using plasma-focus type pinches in multiple arrays at power levels beyond the validity regime of the current scaling law for a single gun. (author)

  4. Design of a new type synchronous focusing mechanism

    Science.gov (United States)

    Zhang, Jintao; Tan, Ruijun; Chen, Zhou; Zhang, Yongqi; Fu, Panlong; Qu, Yachen

    2018-05-01

    Aiming at the dual channel telescopic imaging system composed of infrared imaging system, low-light-level imaging system and image fusion module, In the fusion of low-light-level images and infrared images, it is obvious that using clear source images is easier to obtain high definition fused images. When the target is imaged at 15m to infinity, focusing is needed to ensure the imaging quality of the dual channel imaging system; therefore, a new type of synchronous focusing mechanism is designed. The synchronous focusing mechanism realizes the focusing function through the synchronous translational imaging devices, mainly including the structure of the screw rod nut, the shaft hole coordination structure and the spring steel ball eliminating clearance structure, etc. Starting from the synchronous focusing function of two imaging devices, the structure characteristics of the synchronous focusing mechanism are introduced in detail, and the focusing range is analyzed. The experimental results show that the synchronous focusing mechanism has the advantages of ingenious design, high focusing accuracy and stable and reliable operation.

  5. Focus, accent, and argument structure: effects on language comprehension.

    Science.gov (United States)

    Birch, S; Clifton, C

    1995-01-01

    Four experiments investigated the effect of syntactic argument structure on the evaluation and comprehension of utterances with different patterns of pitch accents. Linguistic analyses of the relation between focus and prosody note that it is possible for certain accented constituents within a broadly focused phrase to project focus to the entire phrase. We manipulated focus requirements and accent in recorded question-answer pairs and asked listeners to make linguistic judgments of prosodic appropriateness (Experiments 1 and 3) or to make judgments based on meaningful comprehension (Experiments 2 and 4). Naive judgments of prosodic appropriateness were generally consistent with the linguistic analyses, showing preferences for utterances in which contextually new noun phrases received accent and old noun phrases did not, but suggested that an accented new argument NP was not fully effective in projecting broad focus to the entire VP. However, the comprehension experiments did demonstrate that comprehension of a sentence with broad VP focus was as efficient when only a lexical argument NP received accent as when both NP and verb received accent. Such focus projection did not occur when the argument NP was an "independent quantifier" such as nobody or everything. The results extend existing demonstrations that the ease of understanding spoken discourse depends on appropriate intonational marking of focus to cases where certain structurally-defined words can project focus-marking to an entire phrase.

  6. Self-focused and other-focused resiliency: Plausible mechanisms linking early family adversity to health problems in college women.

    Science.gov (United States)

    Coleman, Sulamunn R M; Zawadzki, Matthew J; Heron, Kristin E; Vartanian, Lenny R; Smyth, Joshua M

    2016-01-01

    This study examined whether self-focused and other-focused resiliency help explain how early family adversity relates to perceived stress, subjective health, and health behaviors in college women. Female students (N = 795) participated between October 2009 and May 2010. Participants completed self-report measures of early family adversity, self-focused (self-esteem, personal growth initiative) and other-focused (perceived social support, gratitude) resiliency, stress, subjective health, and health behaviors. Using structural equation modeling, self-focused resiliency associated with less stress, better subjective health, more sleep, less smoking, and less weekend alcohol consumption. Other-focused resiliency associated with more exercise, greater stress, and more weekend alcohol consumption. Early family adversity was indirectly related to all health outcomes, except smoking, via self-focused and other-focused resiliency. Self-focused and other-focused resiliency represent plausible mechanisms through which early family adversity relates to stress and health in college women. This highlights areas for future research in disease prevention and management.

  7. EDITORIAL: Focus on Dilute Magnetic Semiconductors FOCUS ON DILUTE MAGNETIC SEMICONDUCTORS

    Science.gov (United States)

    Chambers, Scott A.; Gallagher, Bryan

    2008-05-01

    This focus issue of New Journal of Physics is devoted to the materials science of dilute magnetic semiconductors (DMS). A DMS is traditionally defined as a diamagnetic semiconductor doped with a few to several atomic per cent of some transition metal with unpaired d electrons. Several kinds of dopant-dopant interactions can in principle couple the dopant spins leading to a ferromagnetic ground state in a dilute magnetic system. These include superexchange, which occurs principally in oxides and only between dopants with one intervening oxygen, and double exchange, in which dopants of different formal charges exchange an electron. In both of these mechanisms, the ferromagnetic alignment is not critically dependent on free carriers in the host semiconductor because exchange occurs via bonds. A third mechanism, discovered in the last few years, involves electrons associated with lattice defects that can apparently couple dopant spins. This mechanism is not well understood. Finally, the most desirable mechanism is carrier-mediated exchange interaction in which the dopant spins are coupled by itinerant electrons or holes in the host semiconductor. This mechanism introduces a fundamental link between magnetic and electrical transport properties and offers the possibility of new spintronic functionalities. In particular electrical gate control of ferromagnetism and the use of spin polarized currents to carry signals for analog and digital applications. The spin light emitting diode is a prototypical device of this kind that has been extensively used to characterize the extent of spin polarization in the active light emitting semiconductor heterostructure. The prototypical carrier mediated ferromagnetic DMS is Mn-doped GaAs. This and closely related narrow gap III-V materials have been very extensively studied. Their properties are generally quite well understood and they have led to important insights into fundamental properties of ferromagnetic systems with strong spin

  8. EDITORIAL: Focus on Visualization in Physics FOCUS ON VISUALIZATION IN PHYSICS

    Science.gov (United States)

    Sanders, Barry C.; Senden, Tim; Springel, Volker

    2008-12-01

    cosmology wherein this (in principle invisible) dark matter dominates the cosmic matter content. The advantages of visualization found for simulated data also hold for real world data as well. With the application of computerized acquisition many scientific disciplines are witnessing exponential growth rates of the volume of accumulated raw data, which often makes it daunting to condense the information into a manageable form, a challenge that can be addressed by modern visualization techniques. Such visualizations are also often an enticing way to communicate scientific results to the general public. This need for visualization is especially true in basic science, with its reliance on a benevolent and interested general public that drives the need for high-quality visualizations. Despite the widespread use of visualization, this technology has suffered from a lack of the unifying influence of shared common experiences. As with any emerging technology practitioners have often independently found solutions to similar problems. It is the aim of this focus issue to celebrate the importance of visualization, report on its growing use by the broad community of physicists, including biophysics, chemical physics, geophysics, astrophysics, and medical physics, and provide an opportunity for the diverse community of scientists using visualization to share work in one issue of a journal that itself is in the vanguard of supporting visualization and multimedia. A remarkable breadth and diversity of visualization in physics is to be found in this issue spanning fundamental aspects of relativity theory to computational fluid dynamics. The topics span length scales that are as small as quantum phenomena to the entire observable Universe. We have been impressed by the quality of the submissions and hope that this snap-shot will introduce, inform, motivate and maybe even help to unify visualization in physics. Readers are also directed to the December issue of Physics World which includes

  9. The importance of the right focusing technique. At-a-glance information on focusing techniques in X-ray procedures

    International Nuclear Information System (INIS)

    Lichte-Wichmann, M.

    1993-01-01

    Sharp pictures providing all the information relevant to a particular case obviate repeat exposures, help to keep the radiation dose to a minimum and prevent false diagnoses. In her book, the author gives practical guidance on focusing techniques that is equally valuable to beginners and experienced investigators or medical X-ray assistants and physicians. A substantial part of the book is devoted to detailed instructions on how an object is brought into focus as well as on the criteria of proper focusing and the possibilities of identifying and avoiding false focusing techniques. The problems arising when uncommon X-ray pictures have to be taken are explained by diagrammatic representations. (orig.) [de

  10. Where to Focus so Students Become College and Career Ready

    Science.gov (United States)

    Curry, Donna

    2017-01-01

    In this Forum article, Curry focuses on a few ways math and numeracy instructors can assure their students are ready for college and/or a career. For example, when considering the math levels of so many adult learners, teachers might focus on teaching their students how to reason mathematically, and ensure that they have a solid conceptual…

  11. 21 CFR 312.86 - Focused FDA regulatory research.

    Science.gov (United States)

    2010-04-01

    ... 21 Food and Drugs 5 2010-04-01 2010-04-01 false Focused FDA regulatory research. 312.86 Section 312.86 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED... Severely-debilitating Illnesses § 312.86 Focused FDA regulatory research. At the discretion of the agency...

  12. McKenzie River Focus Watershed Coordination: Fiscal Year 1998.

    Energy Technology Data Exchange (ETDEWEB)

    Runyon, John; Davis-Born, Renee

    1998-01-01

    This report summarizes accomplishments made by the McKenzie River Focus Watershed Council in the areas of coordination and administration during Fiscal Year 1998. Coordination and administration consists of tasks associated with Focus Watershed Council staffing, project management, and public outreach.

  13. Focus on Basics: Connecting Research & Practice. Volume 7, Issue D

    Science.gov (United States)

    Garner, Barbara, Ed.

    2005-01-01

    "Focus on Basics" is the quarterly publication of the National Center for the Study of Adult Learning and Literacy. It presents best practices, current research on adult learning and literacy, and how research is used by adult basic education teachers, counselors, program administrators, and policymakers. "Focus on Basics" is…

  14. Synchrotron radiation focusing by a Bragg--Fresnel lens

    International Nuclear Information System (INIS)

    Aristov, V.V.; Basov, Y.A.; Snigirev, A.A.

    1989-01-01

    Since the discovery of x rays and until the present time the possibilities of their controlling and focusing have been widely discussed. In the hard spectrum region (λ∼1 A) the main focusing schemes are the following: geometrical focusing based on incoherent interaction of wave packets reflected by different regions of bending crystals and coherent (dynamic) focusing performed at the cost of the effect of refraction index angular dispersion near the exact Bragg angle value -θ B . A main disadvantage of geometrical focusing is low spatial resolution (∼0.1 mm) and temperature stability. In the case of coherent focusing a main disadvantage is a narrow angular aperture (∼10 sec. of arc) at spatial resolution (∼1--10 μm). Recently, advances in the development of diffraction physics and microstructuring technology open up possibilities for fabricating effective focusing x-ray optical elements---Bragg--Fresnel lenses (BFL)---with high spatial resolution (∼0.1 μm) at a wide angular aperture and high temperature stability. The present paper describes the main principles of Bragg--Fresnel optics (BFO). It presents the results on the synchrotron experiment and on observation of focusing. In this work the peculiarities of BFL diffraction contrast formation are investigated and image transmission using a BFL is performed. Possibilities of developing x-ray optical schemes of ultrahigh resolution on the basis of BFL elements are also discussed

  15. Plasma focus - dense Z pinch and their applications

    International Nuclear Information System (INIS)

    Ishii, Shozo

    1986-02-01

    ''Workshop on the possibility of Z-pinch as a intense pulse light source'' in 1983 and ''Research meeting on plasma focus and Z-pinch'' in 1984 were held at Institute of Plasma Physics, Nagoya University under a collaborating research program. Research activities reported at the meetings on plasma focus, dense Z-pinch, and related phenomena are summerized. (author)

  16. A historical review on ''magnetic focusing method'' in Japan

    International Nuclear Information System (INIS)

    Yamada, Y.; Tanaka, K.; Abe, Z.

    1986-01-01

    Several topics on the development of the magnetic focusing method and its recent progress are discussed. The magnetic focusing method will be effective for measuring the local NMR parameters, and the advanced imaging technique will also be as useful as the recent conventional NMR Imaging techniques

  17. Alternating gradient focusing and deceleration of polar molecules

    NARCIS (Netherlands)

    Bethlem, H.L.; Tarbutt, M.R.; Kupper, J.; Carty, D.; Wohlfart, K.; Hinds, E.A.; Meijer, G.

    2006-01-01

    Beams of polar molecules can be focused using an array of electrostatic lenses in alternating gradient (AG) configuration. They can also be accelerated or decelerated by applying an appropriate high-voltage switching sequence to the lenses. AG focusing is applicable to molecules in both low-field-

  18. FOCUS: a fire management planning system -- final report

    Science.gov (United States)

    Frederick W. Bratten; James B. Davis; George T. Flatman; Jerold W. Keith; Stanley R. Rapp; Theodore G. Storey

    1981-01-01

    FOCUS (Fire Operational Characteristics Using Simulation) is a computer simulation model for evaluating alternative fire management plans. This final report provides a broad overview of the FOCUS system, describes two major modules-fire suppression and cost, explains the role in the system of gaming large fires, and outlines the support programs and ways of...

  19. Focusing Optics for High-Energy X-ray Diffraction

    DEFF Research Database (Denmark)

    Leinert, U.; Schulze, C.; Honkimäki, V.

    1998-01-01

    Novel focusing optical devices have been developed for synchrotron radiation in the energy range 40-100 keV. Firstly, a narrow-band-pass focusing energy-tuneable fixed-exit monochromator was constructed by combining meridionally bent Laue and Bragg crystals. Dispersion compensation was applied...

  20. Environmental Degradation, Livelihood and Conflicts: A Focus on ...

    African Journals Online (AJOL)

    Environmental Degradation, Livelihood and Conflicts: A Focus on the Implications of the Diminishing Water Resources of Lake Chad for North-Eastern Nigeria. ... The impact of this depletion is being felt by Lake Chad basin population who depend on the lake for their means of livelihood. This paper focuses on the ...

  1. The impact of affective and cognitive focus on attitude formation

    NARCIS (Netherlands)

    Berg, H. van den; Manstead, A.S.R.; Pligt, J. van der; Wigboldus, D.H.J.

    2006-01-01

    We examined the effects of unobtrusive affective and cognitive focus on attitude formation. To induce focus, participants worked on a word-search puzzle consisting of either affective (e.g., emotion) or cognitive (e.g., reasoning) words. They then read positive and negative affective and cognitive

  2. Everyday risk taking as a function of regulatory focus

    NARCIS (Netherlands)

    Hamstra, Melvyn R. W.; Bolderdijk, Jan Willem; Veldstra, Janet L.

    Uncertainty is an inherent aspect of everyday life. However, faced with uncertainty, some individuals take risks more eagerly than others. Regulatory focus theory may explain such differences because risky behavior may arise naturally from the eagerness of promotion focused individuals, while safe

  3. Target focusing configuration for X-ray laser experiments

    International Nuclear Information System (INIS)

    Seppala, L.G.

    1985-01-01

    X-ray laser experiments imposed a new demand on the Novette focusing optics. These optics had to provide highly uniform, double-sided illumination on a target region 1.0 cm long by 100 to 200 μm wide. This line focus requirement had to be achieved without degrading the diagnostic reflection from the last surface of the focus lens and without potential ghost focus problems. The only optical configuration that preserves the diagnostic reflection is shown. A negative focal length cylinder lens is placed between the focus lens and the debris shield, with the concave surface facing toward the focus lens. Any ghost reflections from the cylinder lens or debris shield are degraded by astigmatism, making them less hazardous. In practice, the uniformity of illumination is probably about the same for a positive or a negative cylinder lens. The minimum Novette focused spot was approximately 50 to 75 μm in diameter, and the fabrication errors in the 80-cm-diam precision cylinder lens produced a line focus 25 μm wide. a negative cylinder lens design was chosen, however, to optimize the illumination uniformity in the case of line widths of several hundred microns

  4. Type 1 diabetes and obesity in children : Focus on inflammation

    NARCIS (Netherlands)

    Verrijn Stuart, A.A.

    2013-01-01

    Type 1 diabetes (T1D) is an inflammatory disorder as is obesity. This thesis addresses inflammatory features in both conditions, with focus on inflammatory mediators and the role of adipose tissue (AT). The first part, specific aspects of immune tolerance in T1D,focuses on immune (dys) regulation

  5. Development of a focused ion beam micromachining system

    Energy Technology Data Exchange (ETDEWEB)

    Pellerin, J.G.; Griffis, D.; Russell, P.E.

    1988-12-01

    Focused ion beams are currently being investigated for many submicron fabrication and analytical purposes. An FIB micromachining system consisting of a UHV vacuum system, a liquid metal ion gun, and a control and data acquisition computer has been constructed. This system is being used to develop nanofabrication and nanomachining techniques involving focused ion beams and scanning tunneling microscopes.

  6. On the self-focusing of electric helicons

    International Nuclear Information System (INIS)

    Tsintadze, N.L.; El-Ashry, M.Y.; Garuchava, D.P.

    1987-07-01

    The present work is devoted to the investigation of the stationary self-focusing of circularly polarized helicons in a magnetized plasma in the case of ultra-relativistic intensities. It is shown that the larger intensity and effective width at the boundary is the much faster growing self-focusing. (author). 8 refs

  7. Focus Cities : Improving the Living Environment in Underserved ...

    International Development Research Centre (IDRC) Digital Library (Canada)

    IDRC's Focus Cities research program brings together researchers, municipal authorities, civil society organizations, the private sector and the poor to engage in urban environmental research with the goal of alleviating urban poverty. This project was selected as one of the four highest ranked in the 2005 Focus Cities ...

  8. A Marxist Focus on Comparative Education in Cuba

    Science.gov (United States)

    Cruz, Rosa María Massón

    2015-01-01

    This paper builds systematically on the research experiences of the author, involving the application of a Marxist focus in comparative education studies, in the Cuban and Latin American context. It reflects in a general way the importance of this focus and approach, and in turn the contradictions that occur between formal education policy and…

  9. Simultaneous spatio-temporal focusing for tissue manipulation

    Directory of Open Access Journals (Sweden)

    Squier J.

    2013-11-01

    Full Text Available Simultaneous spatiotemporal focusing (SSTF is applied to lens tissue and compared directly with standard femtosecond micromachining of the tissue at the same numerical aperture. Third harmonic generation imaging is used for spatio-temporal characterization of the processing conditions obtained with both a standard and SSTF focus.

  10. Effects of attentional focus on walking stability in elderly

    NARCIS (Netherlands)

    de Melker Worms, Jonathan L.A.; Stins, John F.; van Wegen, Erwin E.H.; Verschueren, Sabine M.P.; Beek, Peter J.; Loram, Ian D.

    2017-01-01

    Introduction Balance performance in the elderly is related to psychological factors such as attentional focus. We investigated the effects of internal vs. external focus of attention and fall history on walking stability in healthy older adults. Method Walking stability of twenty-eight healthy older

  11. Consolidation of the landfill stabilization and contaminant plumes focus areas

    International Nuclear Information System (INIS)

    Brown, J.P.; Wright, J.; Chamberlain, G.S.

    1996-01-01

    The Assistant Secretary of the Office of Environmental Management (EM) on January 25, 1994, formally established five focus areas to implement A New Approach to Environmental Research and Technology Development at the U. S. Department of Energy (DOE) - Action Plan. The goal of this new approach was to conduct a research and technology development program that is focused on overcoming the major obstacles to cleaning up DOE sites and ensuring that the best talent within the Department and the national science communities is used. Two of the five focus areas established were Landfill Stabilization Focus Area (LSFA) and Contaminant Plumes Containment and Remediation Focus Area (PFA), which were located at the Savannah River Operations Office (SR)

  12. Identifying the role of initial wave parameters on tsunami focusing

    Science.gov (United States)

    Aydın, Baran

    2018-04-01

    Unexpected local tsunami amplification, which is referred to as tsunami focusing, is attributed to two different mechanisms: bathymetric features of the ocean bottom such as underwater ridges and dipolar shape of the initial wave itself. In this study, we characterize the latter; that is, we explore how amplitude and location of the focusing point vary with certain geometric parameters of the initial wave such as its steepness and crest length. Our results reveal two important features of tsunami focusing: for mild waves maximum wave amplitude increases significantly with transverse length of wave crest, while location of the focusing point is almost invariant. For steep waves, on the other hand, increasing crest length dislocates focusing point significantly, while it causes a rather small increase in wave maximum.

  13. Development of focused ion beam systems with various ion species

    International Nuclear Information System (INIS)

    Ji Qing; Leung, K.-N.; King, Tsu-Jae; Jiang Ximan; Appleton, Bill R.

    2005-01-01

    Conventional focused ion beam systems employ a liquid-metal ion source (LMIS) to generate high-brightness beams, such as Ga + beams. Recently there has been an increased need for focused ion beams in areas like biological studies, advanced magnetic-film manufacturing and secondary-ion mass spectroscopy (SIMS). In this article, status of development on focused ion beam systems with ion species such as O 2 + , P + , and B + will be reviewed. Compact columns for forming focused ion beams from low energy (∼3keV), to intermediate energy (∼35keV) are discussed. By using focused ion beams, a SOI MOSFET is fabricated entirely without any masks or resist

  14. Discrete and modal focusing effects: principles and applications

    International Nuclear Information System (INIS)

    Stamate, E

    2012-01-01

    Charge flux distribution on the surface of biased electrodes of different geometries immersed in a plasma is investigated by three-dimensional simulations and experiments. It is demonstrated that the sheath surrounding the electrodes that interface insulators acts as an electrostatic lens, focusing the charges to distinct locations on the electrode surface depending on the entrance coordinates at the sheath edge. Two focusing effects are identified. Discrete focusing leads to the formation of a passive surface of no ion impact, near the edge of the electrodes interfacing insulators. Modal focusing results in the formation of certain ‘modal spots’ and/or ‘modal lines’. Several phenomenological aspects and potential applications are reviewed and further discussed, including charge focusing by a three-dimensional plasma–sheath–lens, ion dose uniformity during plasma immersion ion implantation, mass spectrometry and plasma monitoring. (paper)

  15. Discrete and modal focusing effects: principles and applications

    DEFF Research Database (Denmark)

    Stamate, Eugen

    2012-01-01

    Charge flux distribution on the surface of biased electrodes of different geometries immersed in a plasma is investigated by three-dimensional simulations and experiments. It is demonstrated that the sheath surrounding the electrodes that interface insulators acts as an electrostatic lens, focusing...... the charges to distinct locations on the electrode surface depending on the entrance coordinates at the sheath edge. Two focusing effects are identified. Discrete focusing leads to the formation of a passive surface of no ion impact, near the edge of the electrodes interfacing insulators. Modal focusing...... results in the formation of certain ‘modal spots’ and/or ‘modal lines’. Several phenomenological aspects and potential applications are reviewed and further discussed, including charge focusing by a three-dimensional plasma–sheath–lens, ion dose uniformity during plasma immersion ion implantation, mass...

  16. Plasmonic leak-free focusing lens under radially polarized illumination

    International Nuclear Information System (INIS)

    Li, Xiaowei; Tan, Qiaofeng; Bai, Benfeng; Jin, Guofan

    2010-01-01

    A plasmonic leak-free focusing lens with two asymmetric concentric ring slits under radially polarized illumination is proposed. Each ring slit in the plasmonic lens is designed to generate surface plasmon polaritons (SPPs) with a relative initial phase controlled by the ring slit parameters. Through mutual interference of the SPPs with different phases excited by the two concentric ring slits at the output metal–dielectric interface, the field intensity towards the center of the focusing lens can be enhanced while that leaking to the counter-focus direction is effectively suppressed. The optimal parameters of the plasmonic leak-free lens are theoretically obtained by satisfying the above condition and its focusing performance is demonstrated by numerical simulation. Furthermore, a plasmonic leak-free lens with multiple double-slit groups is proposed and discussed, which exhibits a higher energy density at the focusing spot of the output interface

  17. Rocking convex array used for 3D synthetic aperture focusing

    DEFF Research Database (Denmark)

    Andresen, Henrik; Nikolov, Svetoslav; Pedersen, M M

    2008-01-01

    Volumetric imaging can be performed using 1D arrays in combination with mechanical motion. Outside the elevation focus of the array, the resolution and contrast quickly degrade compared to the azimuth plane, because of the fixed transducer focus. The purpose of this paper is to use synthetic...... aperture focusing (SAF) for enhancing the elevation focusing for a convex rocking array, to obtain a more isotropic point spread function. This paper presents further development of the SAF method, which can be used with curved array combined with a rocking motion. The method uses a virtual source (VS...... Kretztechnik, Zipf, Austria). The array has an elevation focus at 60 mm of depth, and the angular rocking velocity is up to 140deg/s. The scan sequence uses an fprf of 4500 - 7000 Hz allowing up to 15 cm of penetration. The full width at half max (FWHM) and main-lobe to side-lobe ratio (MLSL) is used...

  18. Development of TPF-1 plasma focus for education

    Science.gov (United States)

    Picha, R.; Promping, J.; Channuie, J.; Poolyarat, N.; Sangaroon, S.; Traikool, T.

    2017-09-01

    The plasma focus is a device that uses high voltage and electromagnetic force to induce plasma generation and acceleration, in order to cause nuclear reactions. Radiation of various types (X-ray, gamma ray, electrons, ions, neutrons) can be generated using this method during the pinch phase, thus making the plasma focus able to serve as a radiation source. Material testing, modification, and identification are among the current applications of the plasma focus. Other than being an alternative option to isotopic sources, the plasma focus, which requires multidisciplinary team of personnel to design, operate, and troubleshoot, can also serve as an excellent learning device for physics and engineering students in the fields including, but not limited to, plasma physics, nuclear physics, electronics engineering, and mechanical engineering. This work describes the parameters and current status of Thai Plasma Focus 1 (TPF-1) and the characteristics of the plasma being produced in the machine using a Rogowski coil.

  19. Focus Group in Community Mental Health Research: Need for Adaption.

    Science.gov (United States)

    Zupančič, Vesna; Pahor, Majda; Kogovšek, Tina

    2018-04-27

    The article presents an analysis of the use of focus groups in researching community mental health users, starting with the reasons for using them, their implementation in mental health service users' research, and the adaptations of focus group use when researching the experiences of users. Based on personal research experience and a review of scientific publications in the Google Scholar, Web of Science, ProQuest, EBSCOhost, and Scopus databases, 20 articles published between 2010 and 2016 were selected for targeted content analysis. A checklist for reporting on the use of focus groups with community mental health service users, aiming to improve the comparability, verifiability and validity was developed. Adaptations of the implementation of focus groups in relation to participants' characteristics were suggested. Focus groups are not only useful as a scientific research technique, but also for ensuring service users' participation in decision-making in community mental health and evaluating the quality of the mental health system and services .

  20. Focus Groups as Social Arenas for the Negotiation of Normativity

    DEFF Research Database (Denmark)

    Kristiansen, T. M.; Gronkjaer, M.

    2018-01-01

    Aim: This article aims to demonstrate how focus group discussions act as a social arena for the negotiation of social norms and normativity and to discuss the implications for the analysis of focus group discussions. Participants and methods: We have used sequences of group interactions from...... a focus group study on everyday life and chronic illness to demonstrate how methodological tools from conversation analysis and discursive psychology can be used to facilitate a systematic analysis of the negotiation and legitimization of social norms and normativity in focus groups. The empirical data...... consisted of six focus groups with a total of 32 participants. Results: The analysis demonstrated negotiations on normativity concerning four central aspects related to living with chronic illness: negotiating normativity about adjustment to the disease, negotiating normativity about being a dutiful...

  1. Measurements and simulations of focused beam for orthovoltage therapy

    International Nuclear Information System (INIS)

    Abbas, Hassan; Mahato, Dip N.; Satti, Jahangir; MacDonald, C. A.

    2014-01-01

    Purpose: Megavoltage photon beams are typically used for therapy because of their skin-sparing effect. However, a focused low-energy x-ray beam would also be skin sparing, and would have a higher dose concentration at the focal spot. Such a beam can be produced with polycapillary optics. MCNP5 was used to model dose profiles for a scanned focused beam, using measured beam parameters. The potential of low energy focused x-ray beams for radiation therapy was assessed. Methods: A polycapillary optic was used to focus the x-ray beam from a tungsten source. The optic was characterized and measurements were performed at 50 kV. PMMA blocks of varying thicknesses were placed between optic and the focal spot to observe any variation in the focusing of the beam after passing through the tissue-equivalent material. The measured energy spectrum was used to model the focused beam in MCNP5. A source card (SDEF) in MCNP5 was used to simulate the converging x-ray beam. Dose calculations were performed inside a breast tissue phantom. Results: The measured focal spot size for the polycapillary optic was 0.2 mm with a depth of field of 5 mm. The measured focal spot remained unchanged through 40 mm of phantom thickness. The calculated depth dose curve inside the breast tissue showed a dose peak several centimeters below the skin with a sharp dose fall off around the focus. The percent dose falls below 10% within 5 mm of the focus. It was shown that rotating the optic during scanning would preserve the skin-sparing effect of the focused beam. Conclusions: Low energy focused x-ray beams could be used to irradiate tumors inside soft tissue within 5 cm of the surface

  2. The use of focused ethnography in nursing research.

    Science.gov (United States)

    Cruz, Edward Venzon; Higginbottom, Gina

    2013-03-01

    To provide an overview of the relevance and strengths of focused ethnography in nursing research. The paper provides descriptions of focused ethnography and discusses using exemplars to show how focused ethnographies can enhance and understand nursing practice. Orthodox ethnographic approaches may not always be suitable or desirable for research in diverse nursing contexts. Focused ethnography has emerged as a promising method for applying ethnography to a distinct issue or shared experience in cultures or sub-cultures and in specific settings, rather than throughout entire communities. Unfortunately, there is limited guidance on using focused ethnography, particularly as applied to nursing research. Research studies performed by nurses using focused ethnography are summarised to show how they fulfilled three main purposes of the genre in nursing research. Additional citations are provided to help demonstrate the versatility of focused ethnography in exploring distinct problems in a specific context in different populations and groups of people. The unique role that nurses play in health care, coupled with their skills in enquiry, can contribute to the further development of the discipline. Focused ethnography offers an opportunity to gain a better understanding and appreciation of nursing as a profession, and the role it plays in society. Focused ethnography has emerged as a relevant research methodology that can be used by nurse researchers to understand specific societal issues that affect different facets of nursing practice. As nurse researchers endeavour to understand experiences in light of their health and life situations, focused ethnography enables them to understand the interrelationship between people and their environments in the society in which they live.

  3. Enhanced methodology of focus control and monitoring on scanner tool

    Science.gov (United States)

    Chen, Yen-Jen; Kim, Young Ki; Hao, Xueli; Gomez, Juan-Manuel; Tian, Ye; Kamalizadeh, Ferhad; Hanson, Justin K.

    2017-03-01

    As the demand of the technology node shrinks from 14nm to 7nm, the reliability of tool monitoring techniques in advanced semiconductor fabs to achieve high yield and quality becomes more critical. Tool health monitoring methods involve periodic sampling of moderately processed test wafers to detect for particles, defects, and tool stability in order to ensure proper tool health. For lithography TWINSCAN scanner tools, the requirements for overlay stability and focus control are very strict. Current scanner tool health monitoring methods include running BaseLiner to ensure proper tool stability on a periodic basis. The focus measurement on YIELDSTAR by real-time or library-based reconstruction of critical dimensions (CD) and side wall angle (SWA) has been demonstrated as an accurate metrology input to the control loop. The high accuracy and repeatability of the YIELDSTAR focus measurement provides a common reference of scanner setup and user process. In order to further improve the metrology and matching performance, Diffraction Based Focus (DBF) metrology enabling accurate, fast, and non-destructive focus acquisition, has been successfully utilized for focus monitoring/control of TWINSCAN NXT immersion scanners. The optimal DBF target was determined to have minimized dose crosstalk, dynamic precision, set-get residual, and lens aberration sensitivity. By exploiting this new measurement target design, 80% improvement in tool-to-tool matching, >16% improvement in run-to-run mean focus stability, and >32% improvement in focus uniformity have been demonstrated compared to the previous BaseLiner methodology. Matching control and monitoring on multiple illumination conditions, opens an avenue to significantly reduce Focus-Exposure Matrix (FEM) wafer exposure for new product/layer best focus (BF) setup.

  4. EDITORIAL: Focus on Quantum Cryptography: Theory and Practice FOCUS ON QUANTUM CRYPTOGRAPHY: THEORY AND PRACTICE

    Science.gov (United States)

    Lütkenhaus, N.; Shields, A. J.

    2009-04-01

    Quantum cryptography, and especially quantum key distribution (QKD), is steadily progressing to become a viable tool for cryptographic services. In recent years we have witnessed a dramatic increase in the secure bit rate of QKD, as well as its extension to ever longer fibre- and air-based links and the emergence of metro-scale trusted networks. In the foreseeable future even global-scale communications may be possible using quantum repeaters or Earth-satellite links. A handful of start-ups and some bigger companies are already active in the field. The launch of an initiative to form industrial standards for QKD, under the auspices of the European Telecommunication Standards Institute, described in the paper by Laenger and Lenhart in this Focus Issue, can be taken as a sign of the growing commercial interest. Recent progress has seen an increase in the secure bit rate of QKD links, by orders of magnitude, to over 1 Mb s-1. This has resulted mainly from an improvement in the detection technology. Here changes in the way conventional semiconductor detectors are gated, as well as the development of novel devices based on non-linear processes and superconducting materials, are leading the way. Additional challenges for QKD at GHz clock rates include the design of high speed electronics, remote synchronization and high rate random number generation. Substantial effort is being devoted to increasing the range of individual links, which is limited by attenuation and other losses in optical fibres and air links. An important advance in the past few years has been the introduction of protocols with the same scaling as an ideal single-photon set-up. The good news is that these schemes use standard optical devices, such as weak laser pulses. Thanks to these new protocols and improvements in the detection technology, the range of a single fibre link can exceed a few hundred km. Outstanding issues include proving the unconditional security of some of the schemes. Much of the

  5. EDITORIAL: Focus on Iron-Based Superconductors FOCUS ON IRON-BASED SUPERCONDUCTORS

    Science.gov (United States)

    Hosono, Hideo; Ren, Zhi-An

    2009-02-01

    pace of research within the last year, iron-based superconductors have revealed several unique properties such as a high upper critical field and a robustness to impurities. Participation of five 3d-orbitals in the Fermi levels also means that the electronic structure is complex compared with the cuprates. So, we now have a new family of superconductors and it is worth stressing that we have only just begun looking at the many varieties of candidate materials containing an iron square lattice. At this time we do not know whether a material with a critical temperature greater than 100 K exists, or if completely new properties are to be found. However, as a research community we should go ahead with hope and 'strike while the iron is hot'—this saying is always true! This focus issue of New Journal of Physics was put together to provide a broad-based, free-to-read snapshot of the current state of research in this rapidly emerging field. The papers included cover many aspects related to material exploration, physical analysis, and the theory of these materials, and, as editors, we thank the authors for their fine contributions, and the many referees for their considerable efforts that have ensured fast publication. As an aside, the first special issue on this SUBject was published in November 2008 in the Journal of the Physical Society of Japan (vol 77, supplement c) as the proceedings of the International Symposium on Iron-Pnictide Superconductors held in Tokyo on 29-30 June 2008. We would like to encourage the community to read both issues. On a final note we would like to acknowledge the staff of New Journal of Physics for all of their efficient work in bringing this collection to fruition. Focus on Iron-Based Superconductors Contents Microwave response of superconducting pnictides: extended s+/- scenario O V Dolgov, A A Golubov and D Parker Orbital and spin effects for the upper critical field in As-deficient disordered Fe pnictide superconductors G Fuchs, S

  6. A matter of focus: Power-holders feel more responsible after adopting a cognitive other-focus, rather than a self-focus

    NARCIS (Netherlands)

    Scholl, Annika; Sassenberg, Kai; Scheepers, Daan; Ellemers, Naomi|info:eu-repo/dai/nl/086631276; de Wit, Frank

    Social power implies responsibility. Yet, power-holders often follow only their own interests and overlook this responsibility. The present research illuminates how a previously adopted cognitive focus guides perceived responsibility when a person receives high (vs. low) power. In three experiments,

  7. Does Varying Attentional Focus Affect Skill Acquisition in Children? A Comparison of Internal and External Focus Instructions and Feedback

    Science.gov (United States)

    Agar, Charles; Humphries, Charlotte A.; Naquin, Millie; Hebert, Edward; Wood, Ralph

    2016-01-01

    Recently, researchers have concluded that motor skill performance is enhanced when learners adopt an external attentional focus, compared to adopting an internal focus. We extended the line of inquiry to children and examined if skill learning in children was differentially affected by providing instructions and feedback that direct attentional…

  8. The Therapeutic Alliance in Schema-Focused Therapy and Transference-Focused Psychotherapy for Borderline Personality Disorder

    Science.gov (United States)

    Spinhoven, Philip; Giesen-Bloo, Josephine; van Dyck, Richard; Kooiman, Kees; Arntz, Arnoud

    2007-01-01

    This study investigated the quality and development of the therapeutic alliance as a mediator of change in schema-focused therapy (SFT) and transference-focused psychotherapy (TFP) for borderline personality disorder. Seventy-eight patients were randomly allocated to 3 years of biweekly SFT or TFP. Scores of both therapists and patients for the…

  9. Vector fields in a tight laser focus: comparison of models.

    Science.gov (United States)

    Peatross, Justin; Berrondo, Manuel; Smith, Dallas; Ware, Michael

    2017-06-26

    We assess several widely used vector models of a Gaussian laser beam in the context of more accurate vector diffraction integration. For the analysis, we present a streamlined derivation of the vector fields of a uniformly polarized beam reflected from an ideal parabolic mirror, both inside and outside of the resulting focus. This exact solution to Maxwell's equations, first developed in 1920 by V. S. Ignatovsky, is highly relevant to high-intensity laser experiments since the boundary conditions at a focusing optic dictate the form of the focus in a manner analogous to a physical experiment. In contrast, many models simply assume a field profile near the focus and develop the surrounding vector fields consistent with Maxwell's equations. In comparing the Ignatovsky result with popular closed-form analytic vector models of a Gaussian beam, we find that the relatively simple model developed by Erikson and Singh in 1994 provides good agreement in the paraxial limit. Models involving a Lax expansion introduce a divergences outside of the focus while providing little if any improvement in the focal region. Extremely tight focusing produces a somewhat complicated structure in the focus, and requires the Ignatovsky model for accurate representation.

  10. Prosodic Marking of Narrow Focus in Seoul Korean

    Directory of Open Access Journals (Sweden)

    Hae-Sung Jeon

    2017-01-01

    Full Text Available This paper explores prosodic marking of narrow (corrective focus in Seoul Korean. Korean lacks lexical stress and it has a phonologized association between the Accentual Phrase (AP initial segment and intonation. In the experiment, 4 speakers read sentences including a two-item list which were designed to elicit either an L or H AP-initial tone. The durational variations, the pitch events at prosodic boundaries, and 'F''0 'span in 32 sentences read neutrally and 64 sentences read with one of the items under focus were analyzed. The results show that the focused constituent consistently initiates a new prosodic phrase. In comparison to the neutrally spoken or defocused counterpart, the focused constituent was more likely to be realized as an Intonational Phrase (IP in some contexts. Bitonal IP boundary tones were more likely to occur under focus than monotonal tones. In addition, in focused constituents, durational expansion particularly at the phrase-edges, expansion in 'F''0 'span, and raising of the phrase-initial pitch were observed. On the other hand, defocused constituents were not phonetically reduced compared to the neutral counterparts. The results imply that the phonetic cues spreading over the focused constituent complement the exaggerated prosodic boundaries.

  11. Effects of attentional focus on walking stability in elderly.

    Science.gov (United States)

    de Melker Worms, Jonathan L A; Stins, John F; van Wegen, Erwin E H; Verschueren, Sabine M P; Beek, Peter J; Loram, Ian D

    2017-06-01

    Balance performance in the elderly is related to psychological factors such as attentional focus. We investigated the effects of internal vs. external focus of attention and fall history on walking stability in healthy older adults. Walking stability of twenty-eight healthy older adults was assessed by applying random unilateral decelerations on a split-belt treadmill and analysing the resulting balance recovery movements. The internal focus instruction was: concentrate on the movement of your legs, whereas the external focus instruction was: concentrate on the movement of the treadmill. In both conditions participants were asked to look ahead at a screen. Outcome measures were coefficient of variation of step length and step width, and characteristics of the centre of mass velocity time-series as analysed using statistical parametric mapping. Fall history was assessed using a questionnaire. After each perturbation participants required two to three strides to regain a normal gait pattern, as determined by the centre of mass velocity response. No effects were found of internal and external focus of attention instructions and fall history on any of the outcome measures. We conclude that, compared to an internal focus of attention instruction, external focus to the walking surface does not lead to improved balance recovery responses to gait perturbations in the elderly. Copyright © 2017 Elsevier B.V. All rights reserved.

  12. Focusing procedures in time-of-flight mass spectrometry

    International Nuclear Information System (INIS)

    Ioanoviciu, D.

    2002-01-01

    Time-of-flight mass spectrometry is a fast growing field due to its ability to handle very fast processes and due to its theoretically unlimited mass range. The performances of the time-of-flight mass analysers are heavily dependent on the progress in ion optics, a periodically reviewed field. In this presentation the various focusing procedures in time-of-flight mass spectrometry are reviewed. For ions of the same charge and mass flight time differences result from different potentials at the location of formation and from the initial velocity spread. There is no simultaneous space and velocity focusing in time-of-flight mass spectrometry. Space focusing of first and second order can be reached in time-of-flight mass analysers having two homogeneous electric field ion sources followed by a field free space in front of the detector. Single and double stage homogeneous electric field mirrors can focus in time ions of different energies. These different energies result when ions leaving different initial sites and arriving simultaneously to an intermediate space focus. Convenient mass dispersion can be obtained by including a mirror. Initial velocity focusing is obtained by the delayed extraction procedure in drift space and mirror time-of-flight mass analysers. Post source pulse focusing aims at the same purpose. Ion source electrodes of hyperbolic shape, operated by high voltage pulses can bring major improvements of the resolution, especially at high masses. For each focusing procedure the geometric and/or electric conditions are given as well as the aberrations allowing the mass resolution determination. The various focusing procedures are compared and a prediction of their future performances was tempted. (author)

  13. Dual identities: organizational negotiation in STEM-focused Catholic schools

    Science.gov (United States)

    Kloser, Matthew; Wilsey, Matthew; Hopkins, Dawn W.; Dallavis, Julie W.; Lavin, Erin; Comuniello, Michael

    2017-06-01

    In the last decade, STEM-focused schools have opened their doors nationally in the hope of meeting students' contemporary educational needs. Despite the growth of these STEM-focused institutions, minimal research exists that follows how schools make a transition toward a STEM focus and what organizational structures are most conducive to a successful transition. The adoption of a STEM focus has clear implications for a school's organizational identity. For Catholic schools, the negotiation of a new STEM focus is especially complex, as Catholic schools have been shown to generally possess a distinct religious and cultural organizational identity. The adoption of a second, STEM-focused identity raises questions about whether and how these identities can coexist. Framed by perspectives on organizational identity and existing conceptualizations of the cultural and religious hallmarks of Catholic schools, this study utilizes a multiple-case study design to explore the organizational transition of four Catholic K-8 institutions to Catholic STEM-focused schools. These cases demonstrate the particular challenges of negotiating multiple organizational identities. While variation existed in how the four schools accommodated these identities, the most promising environments for successful transition drew upon an aggregative model of identity negotiation, that is, when schools attended to both identities, but ensured that the original Catholic identity of the school remained foundational to all decisions. The least successful identity negotiations occurred when there was a lack of common understanding about what comprised a STEM-focused school, leading to minimal buy-in from stakeholders or when a school sought to make the transition for recruitment or marketing rather than mission-driven reasons. Discussion of the more successful identity aggregation provides a framework for schools within and beyond the religious sector that desire to adopt an additional STEM-focused

  14. How to conduct focus groups: researching group priorities through discussion.

    Science.gov (United States)

    1992-01-01

    Focus groups serve to uncover priorities and beliefs of a target group, but health project designers do not always take the time to seek this information beforehand. Focus groups also allow various local subgroups to communicate their concerns before the project starts. Focus groups can also breed ideas and dialogue that individual interviews cannot and they provide baseline information so managers can determine if attitudes or priorities have resulted from the project. Diverse people have different beliefs, e.g., women who have young children view oral rehydration therapy differently from women with no children. Project designers can use these basic differences to arrive at some conclusions about general attitudes. Focus group facilitators should have a discussion outline to help keep the group on the topic of concern. They should limit sessions to 60-90 minutes. Each focus groups should include 8-10 people. It is important to have members of various community subgroups in each group. Yet group designers should be careful not to include within the same group, those who may intimidate other people in the group, e.g., in situations where farmers depend on middlemen, farmers may not be open if middlemen are also in the focus group. Facilitators should launch each session with an attempt to encourage the members to be open and to feel comfortable. For example, in Malawi, a facilitator leads her focus group discussions with songs. Stories are another icebreaker. It is important that all focus groups centering around a certain project discuss the same topics. Facilitators need to stress to the group that all discussions are to be kept confidential. The designers should also carefully word the questions so that facilitators will not impart their bias. Facilitators should not direct the group to certain conclusions, but instead keep the discussions focused.

  15. Development of the focus system for heaven-I

    International Nuclear Information System (INIS)

    Xiang Yihuai; Zhou Chuangzhi; Gong Kun; Ma Jinglong; Dai Hui; Shan Yusheng; Wang Naiyan

    2003-01-01

    This paper introduces the method of guiding the six KrF laser beams into target chamber and the development of focus system in MOPA angular multiplex system for Heaven-I. The six beams are focused to the vacuum target chamber by six plane-convex lenses. The focal spot on the target is measured by UV CCD camera, the diameter of the focal spot of six beams is 290 μm, the focusing power density on the target is 8 x 10 12 W/cm 2

  16. Three-dimensional measurement of a tightly focused laser beam

    Directory of Open Access Journals (Sweden)

    Xiangsheng Xie

    2013-02-01

    Full Text Available The spatial structure of a tightly focused light field is measured with a double knife-edge scanning method. The measurement method is based on the use of a high-quality double knife-edge fabricated from a right-angled silicon fragment mounted on a photodetector. The reconstruction of the three-dimensional structures of tightly focused spots is carried out with both uniform and partially obstructed linearly polarized incident light beams. The optical field distribution is found to deviate substantially from the input beam profile in the tightly focused region, which is in good agreement with the results of numerical simulations.

  17. Tight focusing of radially polarized circular Airy vortex beams

    Science.gov (United States)

    Chen, Musheng; Huang, Sujuan; Shao, Wei

    2017-11-01

    Tight focusing properties of radially polarized circular Airy vortex beams (CAVB) are studied numerically. The light field expressions for the focused fields are derived based on vectorial Debye theory. We also study the relationship between focal profiles, such as light intensity distribution, radius of focal spot and focal length, and the parameters of CAVB. Numerical results demonstrate that we can generate a radially polarized CAVB with super-long focal length, super-strong longitudinal intensity or subwavelength focused spot at the focal plane by properly choosing the parameters of incident light and high numerical aperture (NA) lens. These results have potential applications for optical trapping, optical storage and particle acceleration.

  18. Inertial particle focusing in serpentine channels on a centrifugal platform

    Science.gov (United States)

    Shamloo, Amir; Mashhadian, Ali

    2018-01-01

    Inertial particle focusing as a powerful passive method is widely used in diagnostic test devices. It is common to use a curved channel in this approach to achieve particle focusing through balancing of the secondary flow drag force and the inertial lift force. Here, we present a focusing device on a disk based on the interaction of secondary flow drag force, inertial lift force, and centrifugal forces to focus particles. By choosing a channel whose cross section has a low aspect ratio, the mixing effect of the secondary flow becomes negligible. To calculate inertial lift force, which is exerted on the particle from the fluid, the interaction between the fluid and particle is investigated accurately through implementation of 3D Direct Numerical Solution (DNS) method. The particle focusing in three serpentine channels with different corner angles of 75°, 85°, and 90° is investigated for three polystyrene particles with diameters of 8 μm, 9.9 μm, and 13 μm. To show the simulation reliability, the results obtained from the simulations of two examples, namely, particle focusing and centrifugal platform, are verified against experimental counterparts. The effects of angular velocity of disk on the fluid velocity and on the focusing parameters are studied. Fluid velocity in a channel with corner angle of 75° is greater than two other channels. Furthermore, the particle equilibrium positions at the cross section of channel are obtained at the outlet. There are two equilibrium positions located at the centers of the long walls. Finally, the effect of particle density on the focusing length is investigated. A particle with a higher density and larger diameter is focused in a shorter length of the channel compared to its counterpart with a lower density and shorter diameter. The channel with a corner angle of 90° has better focusing efficiency compared to other channels. This design focuses particles without using any pump or sheath flow. Inertial particle focusing

  19. Electrical characteristics of a small plasma focus device

    International Nuclear Information System (INIS)

    Choi, P.; Favre, M.; Silva, P.; Chuaqui, H.; Wyndham, E.

    1996-01-01

    Efficient plasma focus operation relies on uniform initial breakdown across the insulator surface. The basic plasma focus electric circuit is discussed in order to highlight circuit modifications that produce high voltage oscillation at the initial breakdown time. Superimposed on the main discharge voltage, such oscillating voltage has been found in real systems to enhance the initial gas breakdown by localizing the initial current path across the insulator surface. PSPICE circuit simulations are compared with electric signals from different operational plasma focus devices. (author). 3 figs., 7 refs

  20. A superconducting focusing solenoid for the neutrino factory linear accelerator

    International Nuclear Information System (INIS)

    Green, Michael A.; Lebedev, V.; Strauss, B.P.

    2001-01-01

    The proposed linear Accelerator that accelerates muons from 190 MeV to 2.45 GeV will use superconducting solenoids for focusing the muon beam. The accelerator will use superconducting RF cavities. These cavities are very sensitive to stay magnetic field from the focusing magnets. Superconducting solenoids can produce large stray fields. This report describes the 201.25 MHz acceleration system for the neutrino factory. This report also describes a focusing solenoid that delivers almost no stray field to a neighboring superconducting RF cavity