WorldWideScience

Sample records for focus compensating sensing

  1. Novel temperature compensation technique for force-sensing piezoresistive devices

    Scott, Joshua; Enikov, Eniko T

    2011-01-01

    A novel stress-insensitive piezoresistor in the shape of an annulus has been developed to be used in conjunction with a piezoresistive bridge for temperature-compensated force measurements. Under uniform stress conditions, the annular resistor shows near-zero stress sensitivity and a linear response to temperature excitation within test conditions of 24–34 °C. Annular resistors were placed in close proximity to stress-sensitive elements in order to detect local temperature fluctuations. Experiments evaluating the performance of the temperature compensator while testing force sensitivity showed a thermal rejection ratio of 37.2 dB and near elimination of low-frequency noise (drift) below 0.07 Hz. Potential applications of this annular resistor include use in multi-axis force sensors for force feedback microassembly, improvements in the simplicity and robustness of high precision microgram sensitive balances, higher accuracy for silicon diaphragm-based pressure sensors and simple temperature compensation for AFM cantilevers.

  2. Calibration and Distortion Field Compensation of Gradiometer and the Improvement in Object Remote Sensing

    Hu Xiangchao

    2016-01-01

    Full Text Available Magnetometer, misalignment error and distortion field can reduce the accuracy of gradiometers. So, it is important to calibrate and compensate gradiometers error. Scale factor, bias, nonorthogonality, misalignment and distortion field should be considered. A gradiometer is connected by an aluminium frame, which contains two fluxgate magnetometers. A nonmagnetic rotation equipment is used to change gradiometer attitude, and the compensation parameters are estimated. Experiment results show that, after calibration and compensation, error of each axis is reduced from 888.4 nT, 1292.6 nT and 168.9 nT to 15.3 nT, 22.1 nT and 9.9 nT, respectively. It shows that the proposed method can calibrate gradiometer and compensate distortion field. After calibration and compensation, the object remote sensing performance is improved.

  3. Compressed sensing techniques for receiver based post-compensation of transmitter's nonlinear distortions in OFDM systems

    Owodunni, Damilola S.; Ali, Anum Z.; Quadeer, Ahmed Abdul; Al-Safadi, Ebrahim B.; Hammi, Oualid; Al-Naffouri, Tareq Y.

    2014-01-01

    -domain, and three compressed sensing based algorithms are presented to estimate and compensate for these distortions at the receiver using a few and, at times, even no frequency-domain free carriers (i.e. pilot carriers). The first technique is a conventional

  4. Numerical tilting compensation in microscopy based on wavefront sensing using transport of intensity equation method

    Hu, Junbao; Meng, Xin; Wei, Qi; Kong, Yan; Jiang, Zhilong; Xue, Liang; Liu, Fei; Liu, Cheng; Wang, Shouyu

    2018-03-01

    Wide-field microscopy is commonly used for sample observations in biological research and medical diagnosis. However, the tilting error induced by the oblique location of the image recorder or the sample, as well as the inclination of the optical path often deteriorates the imaging quality. In order to eliminate the tilting in microscopy, a numerical tilting compensation technique based on wavefront sensing using transport of intensity equation method is proposed in this paper. Both the provided numerical simulations and practical experiments prove that the proposed technique not only accurately determines the tilting angle with simple setup and procedures, but also compensates the tilting error for imaging quality improvement even in the large tilting cases. Considering its simple systems and operations, as well as image quality improvement capability, it is believed the proposed method can be applied for tilting compensation in the optical microscopy.

  5. Gene dosage compensation calibrates four regulatory RNAs to control Vibrio cholerae quorum sensing

    Svenningsen, Sine L; Tu, Kimberly C; Bassler, Bonnie L

    2009-01-01

    the quorum regulatory RNAs 1-4 (Qrr1-4). The four Qrr sRNAs are functionally redundant. That is, expression of any one of them is sufficient for wild-type quorum-sensing behaviour. Here, we show that the combined action of two feedback loops, one involving the sRNA-activator LuxO and one involving the sRNA......Quorum sensing is a mechanism of cell-to-cell communication that allows bacteria to coordinately regulate gene expression in response to changes in cell-population density. At the core of the Vibrio cholerae quorum-sensing signal transduction pathway reside four homologous small RNAs (sRNAs), named......-target HapR, promotes gene dosage compensation between the four qrr genes. Gene dosage compensation adjusts the total Qrr1-4 sRNA pool and provides the molecular mechanism underlying sRNA redundancy. The dosage compensation mechanism is exquisitely sensitive to small perturbations in Qrr levels. Precisely...

  6. Motion compensation with skin contact control for high intensity focused ultrasound surgery in moving organs

    Diodato, A.; Cafarelli, A.; Schiappacasse, A.; Tognarelli, S.; Ciuti, G.; Menciassi, A.

    2018-02-01

    High intensity focused ultrasound (HIFU) is an emerging therapeutic solution that enables non-invasive treatment of several pathologies, mainly in oncology. On the other hand, accurate targeting of moving abdominal organs (e.g. liver, kidney, pancreas) is still an open challenge. This paper proposes a novel method to compensate the physiological respiratory motion of organs during HIFU procedures, by exploiting a robotic platform for ultrasound-guided HIFU surgery provided with a therapeutic annular phased array transducer. The proposed method enables us to keep the same contact point between the transducer and the patient’s skin during the whole procedure, thus minimizing the modification of the acoustic window during the breathing phases. The motion of the target point is compensated through the rotation of the transducer around a virtual pivot point, while the focal depth is continuously adjusted thanks to the axial electronically steering capabilities of the HIFU transducer. The feasibility of the angular motion compensation strategy has been demonstrated in a simulated respiratory-induced organ motion environment. Based on the experimental results, the proposed method appears to be significantly accurate (i.e. the maximum compensation error is always under 1 mm), thus paving the way for the potential use of this technique for in vivo treatment of moving organs, and therefore enabling a wide use of HIFU in clinics.

  7. Fixed-focus camera objective for small remote sensing satellites

    Topaz, Jeremy M.; Braun, Ofer; Freiman, Dov

    1993-09-01

    An athermalized objective has been designed for a compact, lightweight push-broom camera which is under development at El-Op Ltd. for use in small remote-sensing satellites. The high performance objective has a fixed focus setting, but maintains focus passively over the full range of temperatures encountered in small satellites. The lens is an F/5.0, 320 mm focal length Tessar type, operating over the range 0.5 - 0.9 micrometers . It has a 16 degree(s) field of view and accommodates various state-of-the-art silicon detector arrays. The design and performance of the objective is described in this paper.

  8. Compressed sensing techniques for receiver based post-compensation of transmitter's nonlinear distortions in OFDM systems

    Owodunni, Damilola S.

    2014-04-01

    In this paper, compressed sensing techniques are proposed to linearize commercial power amplifiers driven by orthogonal frequency division multiplexing signals. The nonlinear distortion is considered as a sparse phenomenon in the time-domain, and three compressed sensing based algorithms are presented to estimate and compensate for these distortions at the receiver using a few and, at times, even no frequency-domain free carriers (i.e. pilot carriers). The first technique is a conventional compressed sensing approach, while the second incorporates a priori information about the distortions to enhance the estimation. Finally, the third technique involves an iterative data-aided algorithm that does not require any pilot carriers and hence allows the system to work at maximum bandwidth efficiency. The performances of all the proposed techniques are evaluated on a commercial power amplifier and compared. The error vector magnitude and symbol error rate results show the ability of compressed sensing to compensate for the amplifier\\'s nonlinear distortions. © 2013 Elsevier B.V.

  9. Compensation of aberrations of deflected electron probe by means of dynamical focusing with stigmator

    Baba, Norio; Ebe, Toyoe; Ikehata, Koichi; Ito, Yasuhiro; Terada, Hiroshi

    1979-01-01

    Electron beam passing through a deflecting field is in general, subjected to aberrations such as distortion, astigmatism and coma in accordance with the deflecting angle. Accordingly the aberration defect of deflected beam is the most serious limiting factor in the performances of micromachining, microminiaturization and high resolution scanning electron microscopes. From many investigators' results, it is obvious that three important compensation methods to aberrations exist in principle, i.e., double deflection system, dynamical focusing, and the dynamical correction using a stigmator. In this paper, based on the aberration formula derived from the eikonal or the path method, the practical data of the aberration constants of deflected electron beam for the sequential deflection system with parallel plates are calculated, and using its result, the distorted spot patterns of an electron probe deflected in two-dimensional directions for various defocusings are graphically displayed by the aid of a computer. Further, by means of the dynamical focusing with a stigmator, the conditions to completely compensate the second order astigmatic aberration are derived, and spot patterns and the electron density distributions within the spots in the case when the compensating conditions are satisfied are also graphically displayed. (Wakatsuki, Y.)

  10. A Nonlinear Multiparameters Temperature Error Modeling and Compensation of POS Applied in Airborne Remote Sensing System

    Jianli Li

    2014-01-01

    Full Text Available The position and orientation system (POS is a key equipment for airborne remote sensing systems, which provides high-precision position, velocity, and attitude information for various imaging payloads. Temperature error is the main source that affects the precision of POS. Traditional temperature error model is single temperature parameter linear function, which is not sufficient for the higher accuracy requirement of POS. The traditional compensation method based on neural network faces great problem in the repeatability error under different temperature conditions. In order to improve the precision and generalization ability of the temperature error compensation for POS, a nonlinear multiparameters temperature error modeling and compensation method based on Bayesian regularization neural network was proposed. The temperature error of POS was analyzed and a nonlinear multiparameters model was established. Bayesian regularization method was used as the evaluation criterion, which further optimized the coefficients of the temperature error. The experimental results show that the proposed method can improve temperature environmental adaptability and precision. The developed POS had been successfully applied in airborne TSMFTIS remote sensing system for the first time, which improved the accuracy of the reconstructed spectrum by 47.99%.

  11. Depth-of-Interaction Compensation Using a Focused-Cut Scintillator for a Pinhole Gamma Camera

    Alhassen, Fares; Kudrolli, Haris; Singh, Bipin; Kim, Sangtaek; Seo, Youngho; Gould, Robert G.; Nagarkar, Vivek V.

    2011-06-01

    Preclinical SPECT offers a powerful means to understand the molecular pathways of drug interactions in animal models by discovering and testing new pharmaceuticals and therapies for potential clinical applications. A combination of high spatial resolution and sensitivity are required in order to map radiotracer uptake within small animals. Pinhole collimators have been investigated, as they offer high resolution by means of image magnification. One of the limitations of pinhole geometries is that increased magnification causes some rays to travel through the detection scintillator at steep angles, introducing parallax errors due to variable depth-of-interaction in scintillator material, especially towards the edges of the detector field of view. These parallax errors ultimately limit the resolution of pinhole preclinical SPECT systems, especially for higher energy isotopes that can easily penetrate through millimeters of scintillator material. A pixellated, focused-cut (FC) scintillator, with its pixels laser-cut so that they are collinear with incoming rays, can potentially compensate for these parallax errors and thus improve the system resolution. We performed the first experimental evaluation of a newly developed focused-cut scintillator. We scanned a Tc-99 m source across the field of view of pinhole gamma camera with a continuous scintillator, a conventional “straight-cut” (SC) pixellated scintillator, and a focused-cut scintillator, each coupled to an electron-multiplying charge coupled device (EMCCD) detector by a fiber-optic taper, and compared the measured full-width half-maximum (FWHM) values. We show that the FWHMs of the focused-cut scintillator projections are comparable to the FWHMs of the thinner SC scintillator, indicating the effectiveness of the focused-cut scintillator in compensating parallax errors.

  12. Depth-of-Interaction Compensation Using a Focused-Cut Scintillator for a Pinhole Gamma Camera.

    Alhassen, Fares; Kudrolli, Haris; Singh, Bipin; Kim, Sangtaek; Seo, Youngho; Gould, Robert G; Nagarkar, Vivek V

    2011-06-01

    Preclinical SPECT offers a powerful means to understand the molecular pathways of drug interactions in animal models by discovering and testing new pharmaceuticals and therapies for potential clinical applications. A combination of high spatial resolution and sensitivity are required in order to map radiotracer uptake within small animals. Pinhole collimators have been investigated, as they offer high resolution by means of image magnification. One of the limitations of pinhole geometries is that increased magnification causes some rays to travel through the detection scintillator at steep angles, introducing parallax errors due to variable depth-of-interaction in scintillator material, especially towards the edges of the detector field of view. These parallax errors ultimately limit the resolution of pinhole preclinical SPECT systems, especially for higher energy isotopes that can easily penetrate through millimeters of scintillator material. A pixellated, focused-cut (FC) scintillator, with its pixels laser-cut so that they are collinear with incoming rays, can potentially compensate for these parallax errors and thus improve the system resolution. We performed the first experimental evaluation of a newly developed focused-cut scintillator. We scanned a Tc-99m source across the field of view of pinhole gamma camera with a continuous scintillator, a conventional "straight-cut" (SC) pixellated scintillator, and a focused-cut scintillator, each coupled to an electron-multiplying charge coupled device (EMCCD) detector by a fiber-optic taper, and compared the measured full-width half-maximum (FWHM) values. We show that the FWHMs of the focused-cut scintillator projections are comparable to the FWHMs of the thinner SC scintillator, indicating the effectiveness of the focused-cut scintillator in compensating parallax errors.

  13. Compensation in Flood Risk Management with a Focus on Shifts in Compensation Regimes Regarding Prevention, Mitigation and Disaster Management

    van Doorn - Hoekveld, Willemijn

    In the Netherlands, the history of water management and water safety especially, goes back centuries. Compensation of damage caused by lawful acts of an administrative body (no-fault liability) is developed mostly in the field of water management and has quite a long history as well. The

  14. Compensation in Flood Risk Management with a Focus on Shifts in Compensation Regimes Regarding Prevention, Mitigation and Disaster Management

    Willemijn van Doorn-Hoekveld

    2014-05-01

    Full Text Available In the Netherlands, the history of water management and water safety especially, goes back centuries. Compensation of damage caused by lawful acts of an administrative body (no-fault liability is developed mostly in the field of water management and has quite a long history as well. The compensation of no-fault liability in the Netherlands since its introduction has been part of public law and not of civil law. This does not mean that the administration cannot be held liable for wrongful actions, in which case private law is applied. There is a strict distinction between wrongful and lawful acts of the administration: both can cause damage, but the way they are compensated differs: for lawful acts, public law is applied and for wrongful acts civil law (tort law is applied. This article only considers public law, because it is the most important branch of law for the compensation of damage caused in the field of water safety. The field of water safety and flood risk management has seen many new developments, of which integration is the latest one. However, the course of flood risk management tends towards more segmentation of responsibilities. No-fault liability and other questions of compensation are also areas that are developing towards more integration. Assessment of  no-fault liability in the field of water safety management cannot be made without taking into consideration the historical development of the responsibility of the state for water management tasks in general. In this contribution, the author addresses the historical development of responsibilities of the state for water management tasks, recent developments in this area and the system of no-fault liability regarding measures to prevent flooding.

  15. Resource-Efficient Fusion with Pre-Compensated Transmissions for Cooperative Spectrum Sensing

    Dayan Adionel Guimarães

    2015-05-01

    Full Text Available Recently, a novel fusion scheme for cooperative spectrum sensing was proposed for saving resources in the control channel. Secondary users (SUs simultaneously report their decisions using binary modulations with the same carrier frequencies. The transmitted symbols add incoherently at the fusion centre (FC, leading to a larger set of symbols in which a subset is associated with the presence of the primary user (PU signal, and another subset is associated with the absence of such a signal. The decision criterion applied for discriminating these subsets works under the assumption that the channel gains are known at the FC. In this paper, we propose a new simultaneous transmission and decision scheme in which the task of channel estimation is shifted from the FC to the SUs, without the need for feeding-back of the estimates to the FC. The estimates are used at the SUs to pre-compensate for the reporting channel phase rotations and to partially compensate for the channel gains. This partial compensation is the result of signal clipping for peak-to-average power ratio (PAPR control. We show, analytically and with simulations, that this new scheme can produce large performance improvements, yet reduces the implementation complexity when compared with the original one.

  16. Extended use of two crossed Babinet compensators for wavefront sensing in adaptive optics

    Paul, Lancelot; Kumar Saxena, Ajay

    2010-12-01

    An extended use of two crossed Babinet compensators as a wavefront sensor for adaptive optics applications is proposed. This method is based on the lateral shearing interferometry technique in two directions. A single record of the fringes in a pupil plane provides the information about the wavefront. The theoretical simulations based on this approach for various atmospheric conditions and other errors of optical surfaces are provided for better understanding of this method. Derivation of the results from a laboratory experiment using simulated atmospheric conditions demonstrates the steps involved in data analysis and wavefront evaluation. It is shown that this method has a higher degree of freedom in terms of subapertures and on the choice of detectors, and can be suitably adopted for real-time wavefront sensing for adaptive optics.

  17. Functional Impairment In People with Schizophrenia: Focus on Employability and Eligibility for Disability Compensation

    Harvey, Philip D.; Heaton, Robert K.; Carpenter, William T.; Green, Michael F.; Gold, James M.; Schoenbaum, Michael

    2012-01-01

    Background The Social Security Administration (SSA) is considering whether schizophrenia may warrant inclusion in their new “Compassionate Allowance” process, which aims to identify diseases and other medical conditions that invariably quality for Social Security disability benefits and require no more than minimal objective medical information. This paper summarizes evidence on the empirical association between schizophrenia and vocational disability. A companion paper examines the reliability and validity of schizophrenia diagnosis which is critically relevant for granting a long-term disability on the basis of current diagnosis. Methods This is a selective literature review and synthesis, based on a work plan developed in a meeting of experts convened by the National Institute of Mental Health and the SSA. This review of the prevalence of disability is focused on the criteria for receipt of disability compensation for psychotic disorders currently employed by the SSA. Results Disability in multiple functional domains is detected in nearly every person with schizophrenia. Clinical remission is much more common than functional recovery, but most patients experience occasional relapses even with treatment adherence, and remissions do not predict functional recovery. Under SSA’s current disability determination process, approximately 80% of SSDI/SSI applications in SSA’s diagnostic category of “Schizophrenia/Paranoid Functional Disorders” are allowed, compared to around half of SSDI/SSI applications overall. Moreover, the allowance rate is even higher among applicants with schizophrenia. Many unsuccessful applicants are not denied, but rather simply are unable to manage the process of appeal after initial denials. Discussion Research evidence suggests that disability applicants with a valid diagnosis of schizophrenia have significant impairment across multiple dimensions of functioning, and will typically remain impaired for the duration of normal

  18. Future time perspective, regulatory focus, and selection, optimization, and compensation: Testing a longitudinal model

    Baltes, B.B.; Wynne, K.; Sirabian, M.; Krenn, D.; Lange, A.H. de

    2014-01-01

    This study examines the behavioral processes through which future time perspective (FTP) and regulatory focus may influence coping behaviors in older workers. A three-wave longitudinal study was conducted to test a novel model, positing that FTP affects regulatory focus, which then influences the

  19. Narratives of Compensated Dating of Girls in Hong Kong Using Routine Activity Theory: Results of a Focus Group Study of Guardians.

    Li, Jessica C M; Cheung, Chau-Kiu; Jia, Cindy X S; Yu, Yolanda M Y; Nguyen, Ping

    2018-02-01

    This article presents public discourses on compensated dating of adolescent girls in Chinese society. Data are obtained from eight focus groups comprising 50 guardians at private, parochial, and public levels (i.e., social workers, police officers, parents of students, and community representatives). Qualitative data are used to demonstrate how the guardians conceptualize and contextualize compensated dating as an outcome of the dynamics of societal features. Social features such as contemporary ideologies, Internet technology advancement, commercialization of human relationships, and ambiguity between "right" and "wrong" motivate the service providers and customers of compensated dating, and accelerate their convergence and weakened levels of guardianship in society. This study is the first to connect the features of compensated dating of adolescent girls with recent societal changes using the routine activity approach. The findings confirm the application of the routine activity approach in the phenomenon of girls' compensated dating, and also offer theoretical and practical implications.

  20. Stable and efficient Q-compensated least-squares migration with compressive sensing, sparsity-promoting, and preconditioning

    Chai, Xintao; Wang, Shangxu; Tang, Genyang; Meng, Xiangcui

    2017-10-01

    The anelastic effects of subsurface media decrease the amplitude and distort the phase of propagating wave. These effects, also referred to as the earth's Q filtering effects, diminish seismic resolution. Ignoring anelastic effects during seismic imaging process generates an image with reduced amplitude and incorrect position of reflectors, especially for highly absorptive media. The numerical instability and the expensive computational cost are major concerns when compensating for anelastic effects during migration. We propose a stable and efficient Q-compensated imaging methodology with compressive sensing, sparsity-promoting, and preconditioning. The stability is achieved by using the Born operator for forward modeling and the adjoint operator for back propagating the residual wavefields. Constructing the attenuation-compensated operators by reversing the sign of attenuation operator is avoided. The method proposed is always stable. To reduce the computational cost that is proportional to the number of wave-equation to be solved (thereby the number of frequencies, source experiments, and iterations), we first subsample over both frequencies and source experiments. We mitigate the artifacts caused by the dimensionality reduction via promoting sparsity of the imaging solutions. We further employ depth- and Q-preconditioning operators to accelerate the convergence rate of iterative migration. We adopt a relatively simple linearized Bregman method to solve the sparsity-promoting imaging problem. Singular value decomposition analysis of the forward operator reveals that attenuation increases the condition number of migration operator, making the imaging problem more ill-conditioned. The visco-acoustic imaging problem converges slower than the acoustic case. The stronger the attenuation, the slower the convergence rate. The preconditioning strategy evidently decreases the condition number of migration operator, which makes the imaging problem less ill-conditioned and

  1. Focus in High School Mathematics: Reasoning and Sense Making in Geometry

    National Council of Teachers of Mathematics, 2010

    2010-01-01

    Classically, geometry has been the subject in which students encounter mathematical proof based on formal deduction. Attention to proof in the geometry curriculum is strengthened by a focus on reasoning and sense making. This book examines the four key elements (conjecturing about geometric objects, construction and evaluation of geometric…

  2. Compressed sensing based joint-compensation of power amplifier's distortions in OFDMA cognitive radio systems

    Ali, Anum Z.

    2013-12-01

    Linearization of user equipment power amplifiers driven by orthogonal frequency division multiplexing signals is addressed in this paper. Particular attention is paid to the power efficient operation of an orthogonal frequency division multiple access cognitive radio system and realization of such a system using compressed sensing. Specifically, precompensated overdriven amplifiers are employed at the mobile terminal. Over-driven amplifiers result in in-band distortions and out of band interference. Out of band interference mostly occupies the spectrum of inactive users, whereas the in-band distortions are mitigated using compressed sensing at the receiver. It is also shown that the performance of the proposed scheme can be further enhanced using multiple measurements of the distortion signal in single-input multi-output systems. Numerical results verify the ability of the proposed setup to improve error vector magnitude, bit error rate, outage capacity and mean squared error. © 2011 IEEE.

  3. Compressed sensing based joint-compensation of power amplifier's distortions in OFDMA cognitive radio systems

    Ali, Anum Z.; Hammi, Oualid; Al-Naffouri, Tareq Y.

    2013-01-01

    Linearization of user equipment power amplifiers driven by orthogonal frequency division multiplexing signals is addressed in this paper. Particular attention is paid to the power efficient operation of an orthogonal frequency division multiple access cognitive radio system and realization of such a system using compressed sensing. Specifically, precompensated overdriven amplifiers are employed at the mobile terminal. Over-driven amplifiers result in in-band distortions and out of band interference. Out of band interference mostly occupies the spectrum of inactive users, whereas the in-band distortions are mitigated using compressed sensing at the receiver. It is also shown that the performance of the proposed scheme can be further enhanced using multiple measurements of the distortion signal in single-input multi-output systems. Numerical results verify the ability of the proposed setup to improve error vector magnitude, bit error rate, outage capacity and mean squared error. © 2011 IEEE.

  4. Reactive power compensating system

    Williams, Timothy J. (Redondo Beach, CA); El-Sharkawi, Mohamed A. (Renton, WA); Venkata, Subrahmanyam S. (Seattle, WA)

    1987-01-01

    The reactive power of an induction machine is compensated by providing fixed capacitors on each phase line for the minimum compensation required, sensing the current on one line at the time its voltage crosses zero to determine the actual compensation required for each phase, and selecting switched capacitors on each line to provide the balance of the compensation required.

  5. An approach to enhance self-compensation capability in paper-based devices for chemical sensing.

    Lo, Shih-Jie; Chen, Kuan-Hung; Yao, Da-Jeng

    2015-12-01

    This paper describes a simple design for increasing the tolerance of reagent dislocation on a paper-based platform using a combination of wax-treated paper and a vortex mixer. To date, massive budgetary funds are required in the biotechnological industry to develop new applications; a large part of that cost is attributable to the screening of specific chemical compounds. Here, we propose using a liquid-handling robot to automatically deposit selected reagents on a paper-based platform. We also present a preliminary concept approach for developing a reagent placing device with simple and inexpensive features. A defect of inaccuracy was observed between droplet location and test well location after viewing the performance of the liquid-handling robot on our paper-based platform. Because of dislocation error resulting from robotic reagent placement, we decided to apply an external, rotational force following droplet placement in order to compensate for the distance of reagent dislocation. Note, the largest distance of reagent dislocation was determined by examining the results of altering applied reagent volume, but not concentration, in volumes from 5 µL to 30 µL in a series of experiments. As a result of these experiments, we observed that dislocation was positively affected by an increase in applied volume. A colorimetric assay for nitrite detection was also performed to confirm the feasibility of this method. This work, we believe, can minimize the cost of chemical compound screening for the biotechnological industry. Copyright © 2015 Elsevier B.V. All rights reserved.

  6. Optical Remote Sensing of Glacier Characteristics: A Review with Focus on the Himalaya

    Racoviteanu, Adina E.; Williams, Mark W.; Barry, Roger G.

    2008-01-01

    The increased availability of remote sensing platforms with appropriate spatial and temporal resolution, global coverage and low financial costs allows for fast, semi-automated, and cost-effective estimates of changes in glacier parameters over large areas. Remote sensing approaches allow for regular monitoring of the properties of alpine glaciers such as ice extent, terminus position, volume and surface elevation, from which glacier mass balance can be inferred. Such methods are particularly useful in remote areas with limited field-based glaciological measurements. This paper reviews advances in the use of visible and infrared remote sensing combined with field methods for estimating glacier parameters, with emphasis on volume/area changes and glacier mass balance. The focus is on the Advanced Spaceborne Thermal Emission and Reflection Radiometer (ASTER) sensor and its applicability for monitoring Himalayan glaciers. The methods reviewed are: volumetric changes inferred from digital elevation models (DEMs), glacier delineation algorithms from multi-spectral analysis, changes in glacier area at decadal time scales, and AAR/ELA methods used to calculate yearly mass balances. The current limitations and on-going challenges in using remote sensing for mapping characteristics of mountain glaciers also discussed, specifically in the context of the Himalaya. PMID:27879883

  7. Integrated dynamic and static tactile sensor: focus on static force sensing

    Wettels, Nicholas; Pletner, Baruch

    2012-04-01

    Object grasping by robotic hands in unstructured environments demands a sensor that is durable, compliant, and responsive to static and dynamic force conditions. In order for a tactile sensor to be useful for grasp control in these, it should have the following properties: tri-axial force sensing (two shear plus normal component), dynamic event sensing across slip frequencies, compliant surface for grip, wide dynamic range (depending on application), insensitivity to environmental conditions, ability to withstand abuse and good sensing behavior (e.g. low hysteresis, high repeatability). These features can be combined in a novel multimodal tactile sensor. This sensor combines commercial-off-the-shelf MEMS technology with two proprietary force sensors: a high bandwidth device based on PZT technology and low bandwidth device based on elastomers and optics. In this study, we focus on the latter transduction mechanism and the proposed architecture of the completed device. In this study, an embedded LED was utilized to produce a constant light source throughout a layer of silicon rubber which covered a plastic mandrel containing a set of sensitive phototransistors. Features about the contacted object such as center of pressure and force vectors can be extracted from the information in the changing patterns of light. The voltage versus force relationship obtained with this molded humanlike finger had a wide dynamic range that coincided with forces relevant for most human grip tasks.

  8. Environmental sensing with optical fiber sensors processed with focused ion beam and atomic layer deposition

    Flores, Raquel; Janeiro, Ricardo; Dahlem, Marcus; Viegas, Jaime

    2015-03-01

    We report an optical fiber chemical sensor based on a focused ion beam processed optical fiber. The demonstrated sensor is based on a cavity formed onto a standard 1550 nm single-mode fiber by either chemical etching, focused ion beam milling (FIB) or femtosecond laser ablation, on which side channels are drilled by either ion beam milling or femtosecond laser irradiation. The encapsulation of the cavity is achieved by optimized fusion splicing onto a standard single or multimode fiber. The empty cavity can be used as semi-curved Fabry-Pérot resonator for gas or liquid sensing. Increased reflectivity of the formed cavity mirrors can be achieved with atomic layer deposition (ALD) of alternating metal oxides. For chemical selective optical sensors, we demonstrate the same FIB-formed cavity concept, but filled with different materials, such as polydimethylsiloxane (PDMS), poly(methyl methacrylate) (PMMA) which show selective swelling when immersed in different solvents. Finally, a reducing agent sensor based on a FIB formed cavity partially sealed by fusion splicing and coated with a thin ZnO layer by ALD is presented and the results discussed. Sensor interrogation is achieved with spectral or multi-channel intensity measurements.

  9. Recent developments in sensing methods for eutrophying nutrients with a focus on automation for environmental applications.

    Duffy, G; Regan, F

    2017-11-20

    The demand for autonomous sensors for unattended, continuous nutrient monitoring in water is rapidly growing with the increasing need for more frequent and widespread environmental pollution monitoring. Legislative bodies, local authorities and industries all require frequent water quality monitoring, however, this is time and labour intensive, and an expensive undertaking. Autonomous sensors allow for frequent, unattended data collection. While this solves the time and labour intensive aspects of water monitoring, sensors can be very expensive. Development of low-cost sensors is essential to realise the concept of Internet of Things (IoT). However there is much work yet to be done in this field. This article reviews current literature on the research and development efforts towards deployable autonomous sensors for phosphorus (in the form of phosphate) and nitrogen (in the form of nitrate), with a focus on analytical performance and cost considerations. Additionally, some recent sensing approaches that could be automated in the future are included, along with an overview of approaches to monitoring both nutrients. These approaches are compared with standard laboratory methods and also with commercially available sensors for both phosphate and nitrate. Application of nutrient sensors in agriculture is discussed as an example of how sensor networks can provide improvements in decision making.

  10. Essays in Executive Compensation

    D. Zhang (Dan)

    2012-01-01

    textabstractThis dissertation focuses on how executive compensation is designed and its implications for corporate finance and government regulations. Chapter 2 analyzes several proposals to restrict CEO compensation and calibrates two models of executive compensation that describe how firms would

  11. Tracking Control of Shape-Memory-Alloy Actuators Based on Self-Sensing Feedback and Inverse Hysteresis Compensation

    Shu-Hung Liu

    2009-12-01

    Full Text Available Shape memory alloys (SMAs offer a high power-to-weight ratio, large recovery strain, and low driving voltages, and have thus attracted considerable research attention. The difficulty of controlling SMA actuators arises from their highly nonlinear hysteresis and temperature dependence. This paper describes a combination of self-sensing and model-based control, where the model includes both the major and minor hysteresis loops as well as the thermodynamics effects. The self-sensing algorithm uses only the power width modulation (PWM signal and requires no heavy equipment. The method can achieve high-accuracy servo control and is especially suitable for miniaturized applications.

  12. Exercises focusing on rotator cuff and scapular muscles do not improve shoulder joint position sense in healthy subjects.

    Lin, Yin-Liang; Karduna, Andrew

    2016-10-01

    Proprioception is essential for shoulder neuromuscular control and shoulder stability. Exercise of the rotator cuff and scapulothoracic muscles is an important part of shoulder rehabilitation. The purpose of this study was to investigate the effect of rotator cuff and scapulothoracic muscle exercises on shoulder joint position sense. Thirty-six healthy subjects were recruited and randomly assigned into either a control or training group. The subjects in the training group received closed-chain and open-chain exercises focusing on rotator cuff and scapulothoracic muscles for four weeks. Shoulder joint position sense errors in elevation, including the humerothoracic, glenohumeral and scapulothoracic joints, was measured. After four weeks of exercise training, strength increased overall in the training group, which demonstrated the effect of exercise on the muscular system. However, the changes in shoulder joint position sense errors in any individual joint of the subjects in the training group were not different from those of the control subjects. Therefore, exercises specifically targeting individual muscles with low intensity may not be sufficient to improve shoulder joint position sense in healthy subjects. Future work is needed to further investigate which types of exercise are more effective in improving joint position sense, and the mechanisms associated with those changes. Copyright © 2016 Elsevier B.V. All rights reserved.

  13. Recent advances in intracellular and in vivo ROS sensing: focus on nanoparticle and nanotube applications.

    Uusitalo, Larissa M; Hempel, Nadine

    2012-01-01

    Reactive oxygen species (ROS) are increasingly being implicated in the regulation of cellular signaling cascades. Intracellular ROS fluxes are associated with cellular function ranging from proliferation to cell death. Moreover, the importance of subtle, spatio-temporal shifts in ROS during localized cellular signaling events is being realized. Understanding the biochemical nature of the ROS involved will enhance our knowledge of redox-signaling. An ideal intracellular sensor should therefore resolve real-time, localized ROS changes, be highly sensitive to physiologically relevant shifts in ROS and provide specificity towards a particular molecule. For in vivo applications issues such as bioavailability of the probe, tissue penetrance of the signal and signal-to-noise ratio also need to be considered. In the past researchers have heavily relied on the use of ROS-sensitive fluorescent probes and, more recently, genetically engineered ROS sensors. However, there is a great need to improve on current methods to address the above issues. Recently, the field of molecular sensing and imaging has begun to take advantage of the unique physico-chemical properties of nanoparticles and nanotubes. Here we discuss the recent advances in the use of these nanostructures as alternative platforms for ROS sensing, with particular emphasis on intracellular and in vivo ROS detection and quantification.

  14. Statistical mapping of zones of focused groundwater/surface-water exchange using fiber-optic distributed temperature sensing

    Mwakanyamale, Kisa; Day-Lewis, Frederick D.; Slater, Lee D.

    2013-01-01

    Fiber-optic distributed temperature sensing (FO-DTS) increasingly is used to map zones of focused groundwater/surface-water exchange (GWSWE). Previous studies of GWSWE using FO-DTS involved identification of zones of focused GWSWE based on arbitrary cutoffs of FO-DTS time-series statistics (e.g., variance, cross-correlation between temperature and stage, or spectral power). New approaches are needed to extract more quantitative information from large, complex FO-DTS data sets while concurrently providing an assessment of uncertainty associated with mapping zones of focused GSWSE. Toward this end, we present a strategy combining discriminant analysis (DA) and spectral analysis (SA). We demonstrate the approach using field experimental data from a reach of the Columbia River adjacent to the Hanford 300 Area site. Results of the combined SA/DA approach are shown to be superior to previous results from qualitative interpretation of FO-DTS spectra alone.

  15. Oil spill detection and remote sensing : an overview with focus on recent events

    Coolbaugh, T.S.

    2008-01-01

    Several offshore oil spills occurred during the period from November to December 2007 in various parts of the world, each highlighting the need of quickly detect oil spills in marine settings. Several factors must be considered in order to determine the best technical approach for successful detection and oil spill monitoring. These include the reason for detection or monitoring; the location of the spill; the scale of spatial coverage; availability of detection equipment and time to deploy; high specificity for petroleum oil; weather conditions at and above the spill site; and cost of the detection approach. This paper outlined some of the key attributes of several remote sensing options that are available today or being considered. The approaches used to enhance visualization or detection of spills include traditional electromagnetic spectrum-based approaches such as ultra violet (UV), visible, infra-red (IR), radar, and fluorescence-based systems. Analytical approaches such as chemical analysis for the detection of volatile organic compounds (VOCs) or monitoring of electrical conductivity of the water surface may also provide a warning that hydrocarbons have been released. 12 refs., 3 tabs., 11 figs

  16. Developing fair compensation structures

    Trousdale, W.J.

    1998-01-01

    The issue of finding an effective way to incorporate Aboriginal values into the process of developing fair compensation structures was discussed. This paper discusses pricing intangible values using dollars, but it was emphasized that 'values' are whatever are important to us. Therefore, in order to achieve fair compensation, creative alternatives that are value-focused should be pursued. In addition to the more straight-forward monetary compensation, compensation could also be about avoiding losses, mitigating adverse impacts, achieving better communication, and promoting cultural understanding. 25 refs., 2 tabs

  17. Creative compensation

    Coll, D.

    1994-01-01

    A discussion is presented of executive compensation in Canada's petroleum industry. Mandatory disclosure of executive compensation and benefits is regulated by the Ontario Securities Commission. Examination of the compensation packages of 80 oilpatch CEOs shows a clear difference in philosophy between large and small companies. Larger companies pay larger salaries, offer pension plans, and reward long-term loyalty. Within smaller companies, compensation tends to be linked with stock performance. Trends in compensation are to lower base salaries with more variables such as bonuses, cash incentives and gain-sharing programs. Increasing shareholder scrutiny is prompting more stringent guidelines on stock option plans. Some companies place performance conditions on stock vesting. Another option is to grant premium priced options to executives, to increase the gains required for the executive to post a profit. Other comapanies are granting stock options to their field personnel, or are granting stock to all employees. Directors are playing an increasing role in executive compensation. 4 tabs

  18. Losses compensation; Compensation des pertes

    NONE

    2001-07-01

    One mission of RTE (Electric Power Transportation), is to watch over the losses compensation resulting from the power transport on the electric power network. Since january 2001, RTE makes good the electric losses by the purchase of energy. To choose the marketers, a consultation has been realized by RTE. This document presents the rules concerning these losses compensation. (A.L.B.)

  19. Verification of Rapid Focused-Recharge in Depressions of Kuwait and the Arabian Peninsula Using Thermal and VNIR Remote Sensing

    Rotz, R. R.; Milewski, A.

    2013-12-01

    In the Arabian Peninsula, freshwater recharge from rainfall is infrequent. Recharge is typically focused in small depressions that fill with seasonal runoff and potentially form freshwater lenses. This phenomenon has been verified in the Raudhatain watershed in Kuwait. This study aims to substantiate previously hypothesized lens locations and detect water in the subsurface by using thermal remote sensing and rainfall data. Potential freshwater lenses (~142) have been previously postulated throughout Kuwait and Saudi Arabia, but lack verification due to inadequate monitoring networks. We hypothesize that due to water's unique heat capacity, recharge zones can be detected by identifying areas with lower changes in surface radiance values than neighboring dry areas between day and night after peak or sustained rainfall. If successful, recharge zones and freshwater lenses can be identified and verified in remote hyper-arid regions. We collected 320 high-resolution (15m - 90m), low cloud cover (lens locations, runoff channels, agricultural regions, and wetlands were detected in areas where radiance values change between 0.067 - 2.25 Wsr-1m-2 from day to night scenes and verified by Google Earth (15m), Landsat (30m), and ASTER VNIR (15m) images. Additionally, two seasonal peak rainfall (~35mm/day) events positively correlate with the surface radiance difference values. Surface radiance values for dry areas adjacent to the postulated lens locations range between 2.25 - 12.2 Wsr-1m-2. Results demonstrate the potential for shallow groundwater detection through the presence of ephemeral water bodies in hyper-arid regions en masse; however, the absence of comparable diurnal images limits data in these regions. Linking high rainfall events with low diurnal surface radiance images is ideal for capturing the presence of temporary surface runoff and recharge zones. Expanded research on hyper-arid regions including thermal values, proposed lens locations, and in-situ data will

  20. Focusing the Lens to Share the Story: Using Photographs and Interviews to Explore Doctoral Students’ Sense of Well-being

    Stefanie Benjamin

    2017-09-01

    Full Text Available Aim/Purpose: This study explores PhD students’ transition into graduate school, which can be a challenging experience for many. Background: Using photographs and in-depth interviews, this study provides nuanced insight into influences on first-year PhD students’ lived experiences, with a specific focus on these students’ perceptions of doctoral student well-being. Methodology: Twenty-nine first-year biomedical science PhD students from 15 research institutions were asked to take photographs (Participant Produced Images to illuminate significant influences on their research skill acquisition. The participant-produced photographs were discussed within in-depth phone interviews allowing for a deeper understanding of their lived experiences. Contribution: While students were asked to identify factors influencing their research skill acquisition, unexpectedly, what emerged from these data was students’ clear focus on their concern for their physical and mental well-being. The researchers posit that students’ ability to create a “work-life balance” is the foundation of doctoral student success, especially in the early years of doctoral training. Findings: Findings suggest that it is essential to create a PhD culture in which students feel valued, supported, and nourished, both physically and mentally, for them to develop into successful researchers, teachers, and mentors. Recommendations for Practitioners: Findings suggest that doctoral programs must support a more collaborative work environment for students and help novice students create a work life balance, perhaps by encouraging them to pursue stimulating or fun activities outside their school environment. It is imperative for doctoral students to be confident during their doctoral studies, as a lack of confidence tends to breathe life into poor work habits that stymie well-being and happiness. Recommendation for Researchers: If doctoral programs support a culture that facilitates

  1. Creative compensation

    Coll, D

    1994-09-19

    A discussion is presented of executive compensation in Canada's petroleum industry. Mandatory disclosure of executive compensation and benefits is regulated by the Ontario Securities Commission. Examination of the compensation packages of 80 oilpatch CEOs shows a clear difference in philosophy between large and small companies. Larger companies pay larger salaries, offer pension plans, and reward long-term loyalty. Within smaller companies, compensation tends to be linked with stock performance. Trends in compensation are to lower base salaries with more variables such as bonuses, cash incentives and gain-sharing programs. Increasing shareholder scrutiny is prompting more stringent guidelines on stock option plans. Some companies place performance conditions on stock vesting. Another option is to grant premium priced options to executives, to increase the gains required for the executive to post a profit. Other comapanies are granting stock options to their field personnel, or are granting stock to all employees. Directors are playing an increasing role in executive compensation. 4 tabs.

  2. Maintaining a focus on opportunities at work : The interplay between age, job complexity, and the use of selection, optimization, and compensation strategies

    Zacher, Hannes; Frese, Michael

    The concept of focus on opportunities describes how many new goals, options, and possibilities employees believe to have in their personal future at work. This study investigated the specific and shared effects of age, job complexity, and the use of successful aging strategies called selection,

  3. Spatial mapping of leaf area index using hyperspectral remote sensing for hydrological applications with a particular focus on canopy interception

    H. H. Bulcock

    2010-02-01

    Full Text Available The establishment of commercial forestry plantations in natural grassland vegetation, results in increased transpiration and interception which in turn, results in a streamflow reduction. Methods to quantify this impact typically require LAI as an input into the various equations and process models that are applied. The use of remote sensing technology as a tool to estimate leaf area index (LAI for use in estimating canopy interception is described in this paper. Remote sensing provides a potential solution to effectively monitor the spatial and temporal variability of LAI. This is illustrated using Hyperion hyperspectral imagery and three vegetation indices, namely the normalized difference vegetation index (NDVI, soil adjusted vegetation index (SAVI and Vogelmann index 1 to estimate LAI in a catchment afforested with Eucalyptus, Pinus and Acacia genera in the KwaZulu-Natal midlands of South Africa. Of the three vegetation indices used in this study, it was found that the Vogelmann index 1 was the most robust index with an R2 and root mean square error (RMSE values of 0.7 and 0.3 respectively. However, both NDVI and SAVI could be used to estimate the LAI of 12 year old Pinus patula accurately. If the interception component is to be quantified independently, estimates of maximum storage capacity and canopy interception are required. Thus, the spatial distribution of LAI in the catchment is used to estimate maximum canopy storage capacity in the study area.

  4. Focusing the Lens to Share the Story: Using Photographs and Interviews to Explore Doctoral Students’ Sense of Well-being

    Stefanie Benjamin; James Williams; Michelle A Maher

    2017-01-01

    Aim/Purpose: This study explores PhD students’ transition into graduate school, which can be a challenging experience for many. Background: Using photographs and in-depth interviews, this study provides nuanced insight into influences on first-year PhD students’ lived experiences, with a specific focus on these students’ perceptions of doctoral student well-being. Methodology: Twenty-nine first-year biomedical science PhD students from 15 research institutions were asked to take photo...

  5. Strategic Design of Teacher Compensation

    Shields, Regis

    2012-01-01

    Spurred by the national focus on revitalizing the teacher evaluation and support/development process, as well as the current economic downturn, many school districts are reviewing how teachers are compensated. While a few courageous districts have completely upended current structures, most districts are undertaking changes that leave the most…

  6. Crime victims‘ right to compensation

    Mrvić-Petrović Nataša

    2012-01-01

    Full Text Available This paper analyzes the most important documents of the United Nations, Council of Europe and the European Union relating to rights to damage compensation (restitution from offender and state compensation. The analysis shows that there is a gradual move from the concept of exercising the rights of victims in favor of a solidaristic model that takes less into account the rights of victims, and more the need to satisfy their legitimate interests. The economic crisis that is undermining the foundations of the welfare state could jeopardize the realization of this concept, especially in those European countries where the criminal justice system focuses solely on the offender, as is the case in Serbia. In such circumstances, regulation which protects the right to compensation, other rights and interests of victims, shall apply only to the extent that serves crime prevention. So it happens that in spite of a suitable normative framework and developments regarding the protection of victims of domestic violence and trafficking, the right to compensation and other rights of the victims do not actually get actualized in practice. In order to overcome this, a systemic reform to the criminal justice system should be undertaken with the aim to redirect the system towards the victim of the offense. Within these reforms a public fund for compensation of the victims of violence should be established and the process of mediation between the victim and the offender with the goal to make a settlement should be regulated, because these mechanisms do not exist in Serbia.

  7. A review on substances and processes relevant for optical remote sensing of extremely turbid marine areas, with a focus on the Wadden Sea

    Hommersom, A.; Wernand, M.R.; Peters, S.W.M.; de Boer, J.

    2010-01-01

    The interpretation of optical remote sensing data of estuaries and tidal flat areas is hampered by optical complexity and often extreme turbidity. Extremely high concentrations of suspended matter, chlorophyll and dissolved organic matter, local differences, seasonal and tidal variations and

  8. Cooperation, compensation and transition

    Ju, Y.

    2004-01-01

    Cooperation and compensation are two important and well-linked issues in economics. The central question in cooperation is how to share the joint gains among participating players. Compensation is a specific aspect of surplus sharing problems providing incentives for agents to sacrifice their own

  9. Options in Compensation

    Flor, Christian Riis; Frimor, Hans; Munk, Claus

    2014-01-01

    We derive the optimal compensation contract in a principal–agent setting in which outcome is used to provide incentives for both effort and risky investments. To motivate investment, optimal compensation entails rewards for high as well as low outcomes, and it is increasing at the mean outcome...

  10. Does CEO compensation impact patient satisfaction?

    Akingbola, Kunle; van den Berg, Herman A

    2015-01-01

    This study examines the relationship between CEO compensation and patient satisfaction in Ontario, Canada. The purpose of this paper is to determine what impact hospital CEO compensation has on hospital patient satisfaction. The analyses in this study were based on data of 261 CEO-hospital-year observations in a sample of 103 nonprofit hospitals. A number of linear regressions were conducted, with patient satisfaction as the dependent variable and CEO compensation as the independent variable of interest. Controlling variables included hospital size, type of hospital, and frequency of adverse clinical outcomes. CEO compensation does not significantly influence hospital patient satisfaction. Both patient satisfaction and CEO compensation appear to be driven primarily by hospital size. Patient satisfaction decreases, while CEO compensation increases, with the number of acute care beds in a hospital. In addition, CEO compensation does not even appear to moderate the influence of hospital size on patient satisfaction. There are several limitations to this study. First, observations of CEO-hospital-years in which annual nominal CEO compensation was below $100,000 were excluded, as they were not publicly available. Second, this research was limited to a three-year range. Third, this study related the compensation of individual CEOs to a measure of performance based on a multitude of patient satisfaction surveys. Finally, this research is restricted to not-for-profit hospitals in Ontario, Canada. The findings seem to suggest that hospital directors seeking to improve patient satisfaction may find their efforts frustrated if they focus exclusively on the hospital CEO. The findings highlight the need for further research on how CEOs may, through leading and supporting those hospital clinicians and staff that interact more closely with patients, indirectly enhance patient satisfaction. To the best of the authors' knowledge, no research has examined the relationship between

  11. Exploring the importance of different items as reasons for leaving emergency medical services between fully compensated, partially compensated, and non-compensated/volunteer samples.

    Blau, Gary; Chapman, Susan; Gibson, Gregory; Bentley, Melissa A

    2011-01-01

    The purpose of our study was to investigate the importance of different items as reasons for leaving the Emergency Medical Service (EMS) profession. An exit survey was returned by three distinct EMS samples: 127 full compensated, 45 partially compensated and 72 non-compensated/volunteer respondents, who rated the importance of 17 different items for affecting their decision to leave EMS. Unfortunately, there were a high percentage of "not applicable" responses for 10 items. We focused on those seven items that had a majority of useable responses across the three samples. Results showed that the desire for better pay and benefits was a more important reason for leaving EMS for the partially compensated versus fully compensated respondents. Perceived lack of advancement opportunity was a more important reason for leaving for the partially compensated and volunteer groups versus the fully compensated group. Study limitations are discussed and suggestions for future research offered.

  12. Reactive power compensator

    El-Sharkawi, Mohamed A.; Venkata, Subrahmanyam S.; Chen, Mingliang; Andexler, George; Huang, Tony

    1992-01-01

    A system and method for determining and providing reactive power compensation for an inductive load. A reactive power compensator (50,50') monitors the voltage and current flowing through each of three distribution lines (52a, 52b, 52c), which are supplying three-phase power to one or more inductive loads. Using signals indicative of the current on each of these lines when the voltage waveform on the line crosses zero, the reactive power compensator determines a reactive power compensator capacitance that must be connected to the lines to maintain a desired VAR level, power factor, or line voltage. Alternatively, an operator can manually select a specific capacitance for connection to each line, or the capacitance can be selected based on a time schedule. The reactive power compensator produces control signals, which are coupled through optical fibers (102/106) to a switch driver (110, 110') to select specific compensation capacitors (112) for connections to each line. The switch driver develops triggering signals that are supplied to a plurality of series-connected solid state switches (350), which control charge current in one direction in respect to ground for each compensation capacitor. During each cycle, current flows from ground to charge the capacitors as the voltage on the line begins to go negative from its positive peak value. The triggering signals are applied to gate the solid state switches into a conducting state when the potential on the lines and on the capacitors reaches a negative peak value, thereby minimizing both the potential difference and across the charge current through the switches when they begin to conduct. Any harmonic distortion on the potential and current carried by the lines is filtered out from the current and potential signals used by the reactive power compensator so that it does not affect the determination of the required reactive compensation.

  13. Reactive power compensator

    El-Sharkawi, Mohamed A. (Renton, WA); Venkata, Subrahmanyam S. (Woodinville, WA); Chen, Mingliang (Kirkland, WA); Andexler, George (Everett, WA); Huang, Tony (Seattle, WA)

    1992-01-01

    A system and method for determining and providing reactive power compensation for an inductive load. A reactive power compensator (50,50') monitors the voltage and current flowing through each of three distribution lines (52a, 52b, 52c), which are supplying three-phase power to one or more inductive loads. Using signals indicative of the current on each of these lines when the voltage waveform on the line crosses zero, the reactive power compensator determines a reactive power compensator capacitance that must be connected to the lines to maintain a desired VAR level, power factor, or line voltage. Alternatively, an operator can manually select a specific capacitance for connection to each line, or the capacitance can be selected based on a time schedule. The reactive power compensator produces control signals, which are coupled through optical fibers (102/106) to a switch driver (110, 110') to select specific compensation capacitors (112) for connections to each line. The switch driver develops triggering signals that are supplied to a plurality of series-connected solid state switches (350), which control charge current in one direction in respect to ground for each compensation capacitor. During each cycle, current flows from ground to charge the capacitors as the voltage on the line begins to go negative from its positive peak value. The triggering signals are applied to gate the solid state switches into a conducting state when the potential on the lines and on the capacitors reaches a negative peak value, thereby minimizing both the potential difference and across the charge current through the switches when they begin to conduct. Any harmonic distortion on the potential and current carried by the lines is filtered out from the current and potential signals used by the reactive power compensator so that it does not affect the determination of the required reactive compensation.

  14. The role of compensation in nuclear waste facility siting. A literature review and real life examples. Deliverable D16b

    Kojo, Matti; Richardson, P.J.

    2009-10-01

    The main objective of this report is to introduce and analyse the local decision-making process in the Eurajoki municipality, Finland regarding the siting of the SNF facility, within the framework of compensation theory. The compensation case Eurajoki offers excellent empirical data for analyzing how the negotiations on compensation were implemented at the local level. The successful siting process is particularly interesting as a number of survey studies have suggested that compensation for a radioactive waste repository does not change the percentage of individuals supporting the facility. On the contrary, some compensation proposals have even decreased the existing support. Even among hazardous waste facilities radioactive waste facilities seem to be an exception. The explanation offered is that radioactive waste is regarded with a greater sense of dread than is the case for other hazardous waste. Although monetary incentives and other benefits have been widely applied in the field of nuclear waste management in many countries the conclusion drawn is that compensation-based siting has to date experienced little success. However, two recent examples, one from Finland and the other from Korea, indicate that compensation can play a decisive role in decision-making during the siting of radioactive waste facilities. Furthermore, in Sweden a local benefit package was agreed between the nuclear waste management company SKB AB and the two candidate municipalities, Oskarshamn and Oesthammar in 2009 before the company announced the site. The novel aspect of this arrangement is that the municipality in which the facility is not located (now known to be Oskarshamn) will receive 75% of the total benefit package (around Euro 200 million) given that Oesthammar will receive all the attendant benefits associated with facility development. The main questions posed in this report are as follows: Why was the compensation package a success in the case of Eurajoki? What were the

  15. Climate change and compensation

    Jensen, Karsten Klint; Flanagan, Tine Bech

    2013-01-01

    This paper presents a case for compensation of actual harm from climate change in the poorest countries. First, it is shown that climate change threatens to reverse the fight to eradicate poverty. Secondly, it is shown how the problems raised in the literature for compensation to some extent...... are based on misconceptions and do not apply to compensation of present actual harm. Finally, two arguments are presented to the effect that, in so far as developed countries accept a major commitment to mitigate climate change, they should also accept a commitment to address or compensate actual harm from...... climate change. The first argument appeals to the principle that if it is an injustice to cause risk of incurring harm in the future, then it is also an injustice to cause a similar harm now. The second argument appeals to the principle that if there is moral reason to reduce the risk of specific harms...

  16. Workers Compensation Claim Data -

    Department of Transportation — This data set contains DOT employee workers compensation claim data for current and past DOT employees. Types of data include claim data consisting of PII data (SSN,...

  17. Magnetic dipole moment estimation and compensation for an accurate attitude control in nano-satellite missions

    Inamori, Takaya; Sako, Nobutada; Nakasuka, Shinichi

    2011-06-01

    Nano-satellites provide space access to broader range of satellite developers and attract interests as an application of the space developments. These days several new nano-satellite missions are proposed with sophisticated objectives such as remote-sensing and observation of astronomical objects. In these advanced missions, some nano-satellites must meet strict attitude requirements for obtaining scientific data or images. For LEO nano-satellite, a magnetic attitude disturbance dominates over other environmental disturbances as a result of small moment of inertia, and this effect should be cancelled for a precise attitude control. This research focuses on how to cancel the magnetic disturbance in orbit. This paper presents a unique method to estimate and compensate the residual magnetic moment, which interacts with the geomagnetic field and causes the magnetic disturbance. An extended Kalman filter is used to estimate the magnetic disturbance. For more practical considerations of the magnetic disturbance compensation, this method has been examined in the PRISM (Pico-satellite for Remote-sensing and Innovative Space Missions). This method will be also used for a nano-astrometry satellite mission. This paper concludes that use of the magnetic disturbance estimation and compensation are useful for nano-satellites missions which require a high accurate attitude control.

  18. Invisible losses and the logics of resettlement compensation.

    Witter, Rebecca; Satterfield, Terre

    2014-10-01

    The necessity of compensating people negatively affected by conservation and other development projects has been widely acknowledged. It is less widely acknowledged that because conventional compensation assessments focus on material resources and their economic equivalents, many important losses incurred by resettlers are invisible to project authorities. Through ethnographic observations and interviews, we documented losses identified by people facing resettlement from Mozambique's Limpopo National Park. We also examined resettlement planning documents to determine why decision makers' assessments of natural resource use and value neglect losses residents identified as critical. Identifying, preventing, and mitigating invisible losses in resettlement planning necessitates a better understanding of intangible benefits residents derive from resources, which are often as or more important than their readily apparent material properties. These benefits include but are not limited to decision-making authority linked to owning land versus having the use of fields; ancestral identity and social belonging linked to gravesites; the importance of tree roots that provide a powerful sense of security because they suppress hunger in periods of scarcity; and the importance of people's location within social networks and hierarchies as they determine the benefits versus risks that will be incurred through resettlement. © 2014 Society for Conservation Biology.

  19. The compensation culture: cliché or cause for concern?

    Hand, James

    2010-01-01

    The 'compensation culture' has featured frequently in the popular press over the last decade. There have, however, been comparatively few academic studies and such studies as there have been have largely focused on personal injury claims. A compensation culture, if it exists, could extend much wider than that. This article compares the exponential increase in the use of the term `compensation culture' in the national printed media since 1995 with available statistics relating to the Queen's B...

  20. The compensation culture: cliché or cause for concern?

    Hand, James

    2010-01-01

    The 'compensation culture' has featured frequently in the popular press over the last decade. There have, however, been comparatively few academic studies and such studies as there have been have largely focused on personal injury claims. A compensation culture, if it exists, could extend much wider than that. This article compares the exponential increase in the use of the term 'compensation culture' in the national printed media since 1995 with available statistics relating to the Queen's B...

  1. Antimicrobial properties of Kalanchoe blossfeldiana: a focus on drug resistance with particular reference to quorum sensing-mediated bacterial biofilm formation.

    Sarkar, Ratul; Mondal, Chaitali; Bera, Rammohan; Chakraborty, Sumon; Barik, Rajib; Roy, Paramita; Kumar, Alekh; Yadav, Kirendra K; Choudhury, Jayanta; Chaudhary, Sushil K; Samanta, Samir K; Karmakar, Sanmoy; Das, Satadal; Mukherjee, Pulok K; Mukherjee, Joydeep; Sen, Tuhinadri

    2015-07-01

    This study attempts to investigate the antimicrobial properties of Kalanchoe blossfeldiana with a particular reference to quorum sensing (QS)-mediated biofilm formation. The methanol extract of K. blossfeldiana leaves (MEKB) was evaluated for antimicrobial properties including QS-controlled production of biofilm (including virulence factor, motility and lactone formation) in Pseudomonas aeruginosa. Methanol extract of K. blossfeldiana was also evaluated for anti-cytokine (tumour necrosis factor-alpha, interleukin-6 and interleukin-1 beta) properties in peripheral blood mononuclear cells (PBMC). Methanol extract of K. blossfeldiana exhibited antimicrobial effect on clinical isolates, as well as standard reference strains. Pseudomonas aeruginosa exposed to MEKB (subminimum inhibitory concentration (MIC)) displayed reduced biofilm formation, whereas supra-MIC produced destruction of preformed biofilms. Methanol extract of K. blossfeldiana reduced the secretion of virulence factors (protease and pyoverdin) along with generation of acyl homoserine lactone (AHL). Confocal laser scanning microscopy images indicate reduction of biofilm thickness. The extract also reduced cytokine formation in lipopolysaccharide-stimulated PBMC. Kalanchoe blossfeldiana was found to interfere with AHL production, which in turn may be responsible for downregulating QS-mediated production of biofilm and virulence. This first report on the antibiofilm and anticytokine properties of this plant may open up new vistas for future exploration of this plant for combating biofilm-related resistant infections. © 2015 Royal Pharmaceutical Society.

  2. Aeromagnetic Compensation for UAVs

    Naprstek, T.; Lee, M. D.

    2017-12-01

    Aeromagnetic data is one of the most widely collected types of data in exploration geophysics. With the continuing prevalence of unmanned air vehicles (UAVs) in everyday life there is a strong push for aeromagnetic data collection using UAVs. However, apart from the many political and legal barriers to overcome in the development of UAVs as aeromagnetic data collection platforms, there are also significant scientific hurdles, primary of which is magnetic compensation. This is a well-established process in manned aircraft achieved through a combination of platform magnetic de-noising and compensation routines. However, not all of this protocol can be directly applied to UAVs due to fundamental differences in the platforms, most notably the decrease in scale causing magnetometers to be significantly closer to the avionics. As such, the methodology must be suitably adjusted. The National Research Council of Canada has collaborated with Aeromagnetic Solutions Incorporated to develop a standardized approach to de-noising and compensating UAVs, which is accomplished through a series of static and dynamic experiments. On the ground, small static tests are conducted on individual components to determine their magnetization. If they are highly magnetic, they are removed, demagnetized, or characterized such that they can be accounted for in the compensation. Dynamic tests can include measuring specific components as they are powered on and off to assess their potential effect on airborne data. The UAV is then flown, and a modified compensation routine is applied. These modifications include utilizing onboard autopilot current sensors as additional terms in the compensation algorithm. This process has been applied with success to fixed-wing and rotary-wing platforms, with both a standard manned-aircraft magnetometer, as well as a new atomic magnetometer, much smaller in scale.

  3. Enthalpy–entropy compensation

    Enthalpy–entropy compensation is the name given to the correlation sometimes observed between the estimates of the enthalpy and entropy of a reaction obtained from temperature-dependence data. Although the mainly artefactual nature of this correlation has been known for many years, the subject enjoys periodical ...

  4. Motion compensated digital tomosynthesis

    van der Reijden, Anneke; van Herk, Marcel; Sonke, Jan-Jakob

    2013-01-01

    Digital tomosynthesis (DTS) is a limited angle image reconstruction method for cone beam projections that offers patient surveillance capabilities during VMAT based SBRT delivery. Motion compensation (MC) has the potential to mitigate motion artifacts caused by respiratory motion, such as blur. The

  5. Teacher Compensation and Organization.

    Kelley, Carolyn

    1997-01-01

    Examines changes in the conceptualization of schooling over time from an organizational perspective. Explores how compensation systems might be better designed to match alternative organizational designs, considering scientific management, effective schools, content-driven schooling, and high standards/high involvement schools as organizational…

  6. (statcom) in synchronous compensator

    eobe

    with fast response and low cost for stabilizing electricity grid power and voltage. ... The conventional and modified Newton-Raphson-based power flow equations .... The control of the reactive power exchange between .... because of its faster rate of convergence and accuracy ..... compensator, North American Power System.

  7. Reactive Power Compensating System.

    Williams, Timothy J.; El-Sharkawi, Mohamed A.; Venkata, Subrahmanyam S.

    1985-01-04

    The circuit was designed for the specific application of wind-driven induction generators. It has great potential for application in any situation where a varying reactive power load is present, such as with induction motors or generators, or for transmission network compensation.

  8. Remote Sensing of Aerosol Backscatter and Earth Surface Targets By Use of An Airborne Focused Continuous Wave CO2 Doppler Lidar Over Western North America

    Jarzembski, Maurice A.; Srivastava, Vandana; Goodman, H. Michael (Technical Monitor)

    2000-01-01

    Airborne lidar systems are used to determine wind velocity and to measure aerosol or cloud backscatter variability. Atmospheric aerosols, being affected by local and regional sources, show tremendous variability. Continuous wave (cw) lidar can obtain detailed aerosol loading with unprecedented high resolution (3 sec) and sensitivity (1 mg/cubic meter) as was done during the 1995 NASA Multi-center Airborne Coherent Atmospheric Wind Sensor (MACAWS) mission over western North America and the Pacific Ocean. Backscatter variability was measured at a 9.1 micron wavelength cw focused CO2 Doppler lidar for approximately 52 flight hours, covering an equivalent horizontal distance of approximately 30,000 km in the troposphere. Some quasi-vertical backscatter profiles were also obtained during various ascents and descents at altitudes that ranged from approximately 0.1 to 12 km. Similarities and differences for aerosol loading over land and ocean were observed. Mid-tropospheric aerosol backscatter background mode was approximately 6 x 10(exp -11)/ms/r, consistent with previous lidar datasets. While these atmospheric measurements were made, the lidar also retrieved a distinct backscatter signal from the Earth's surface from the unfocused part of the focused cw lidar beam during aircraft rolls. Atmospheric backscatter can be highly variable both spatially and temporally, whereas, Earth-surface backscatter is relatively much less variant and can be quite predictable. Therefore, routine atmospheric backscatter measurements by an airborne lidar also give Earth surface backscatter which can allow for investigating the Earth terrain. In the case where the Earth's surface backscatter is coming from a well-known and fairly uniform region, then it can potentially offer lidar calibration opportunities during flight. These Earth surface measurements over varying Californian terrain during the mission were compared with laboratory backscatter measurements using the same lidar of various

  9. Focus on focusing

    Anon.

    1985-01-01

    The discovery and impact of the principle of strong focusing was celebrated at a history Symposium at Stanford on 25 July in the course of the 1985 US Summer School on Particle Accelerators. Burt Richter, Stanford Linac Director, who introduced all the speakers with well chosen reminders about their various contributions related to the theme of the symposium, remarked that it was an appropriate time to be lauding the great contributions of accelerator physicists following the Nobel Prize award to Simon van der Meer for outstanding achievements in accelerator physics

  10. Focus on focusing

    Anon.

    1985-10-15

    The discovery and impact of the principle of strong focusing was celebrated at a history Symposium at Stanford on 25 July in the course of the 1985 US Summer School on Particle Accelerators. Burt Richter, Stanford Linac Director, who introduced all the speakers with well chosen reminders about their various contributions related to the theme of the symposium, remarked that it was an appropriate time to be lauding the great contributions of accelerator physicists following the Nobel Prize award to Simon van der Meer for outstanding achievements in accelerator physics.

  11. Reexamining workers' compensation: a human rights perspective.

    Boden, Leslie I

    2012-06-01

    Injured workers, particularly those with more severe injuries, have long experienced workers' compensation systems as stressful and demeaning, have found it difficult to obtain benefits, and, when able to obtain benefits, have found them inadequate. Moreover, the last two decades have seen a substantial erosion of the protections offered by workers' compensation. State after state has erected additional barriers to benefit receipt, making the workers' compensation experience even more difficult and degrading. These changes have been facilitated by a framing of the political debate focused on the free market paradigm, employer costs, and worker fraud and malingering. The articles in this special issue propose an alternate framework and analysis, a human rights approach, that values the dignity and economic security of injured workers and their families. Copyright © 2012 Wiley Periodicals, Inc.

  12. Appraisal of Phlebotomus argentipes habitat suitability using a remotely sensed index in the kala-azar endemic focus of Bihar, India

    Shreekant Kesari

    2013-04-01

    Full Text Available Visceral leishmaniasis, or kala-azar, is recognised as a serious emerging public health problem in India. In this study, environmental parameters, such as land surface temperature (LST and renormalised difference vegetation indices (RDVI, were used to delineate the association between environmental variables and Phlebotomus argentipes abundance in a representative endemic region of Bihar, India. The adult P. argentipes were collected between September 2009-February 2010 using the hand-held aspirator technique. The distribution of P. argentipes was analysed with the LST and RDVI of the peak and lean seasons. The association between environmental covariates and P. argentipes density was analysed a multivariate linear regression model. The sandfly density at its maximum in September, whereas the minimum density was recorded in January. The regression model indicated that the season, minimum LST, mean LST and mean RDVI were the best environmental covariates for the P. argentipes distribution. The final model indicated that nearly 74% of the variance of sandfly density could be explained by these environmental covariates. This approach might be useful for mapping and predicting the distribution of P. argentipes, which may help the health agencies that are involved in the kala-azar control programme focus on high-risk areas.

  13. Do compensation processes impair mental health? A meta-analysis.

    Elbers, Nieke A; Hulst, Liesbeth; Cuijpers, Pim; Akkermans, Arno J; Bruinvels, David J

    2013-05-01

    Victims who are involved in a compensation processes generally have more health complaints compared to victims who are not involved in a compensation process. Previous research regarding the effect of compensation processes has concentrated on the effect on physical health. This meta-analysis focuses on the effect of compensation processes on mental health. Prospective cohort studies addressing compensation and mental health after traffic accidents, occupational accidents or medical errors were identified using PubMed, EMBASE, PsycInfo, CINAHL, and the Cochrane Library. Relevant studies published between January 1966 and 10 June 2011 were selected for inclusion. Ten studies were included. The first finding was that the compensation group already had higher mental health complaints at baseline compared to the non-compensation group (standardised mean difference (SMD)=-0.38; 95% confidence interval (CI) -0.66 to -0.10; p=.01). The second finding was that mental health between baseline and post measurement improved less in the compensation group compared to the non-compensation group (SMD=-0.35; 95% CI -0.70 to -0.01; p=.05). However, the quality of evidence was limited, mainly because of low quality study design and heterogeneity. Being involved in a compensation process is associated with higher mental health complaints but three-quarters of the difference appeared to be already present at baseline. The findings of this study should be interpreted with caution because of the limited quality of evidence. The difference at baseline may be explained by a selection bias or more anger and blame about the accident in the compensation group. The difference between baseline and follow-up may be explained by secondary gain and secondary victimisation. Future research should involve assessment of exposure to compensation processes, should analyse and correct for baseline differences, and could examine the effect of time, compensation scheme design, and claim settlement on

  14. Center for Worker's Compensation Studies

    Federal Laboratory Consortium — The mission of the NIOSH Center for Workers’ Compensation Studies (CWCS) is to use workers’ compensation data and systems to improve workplace safety and health....

  15. Addressing inadequate compensation | IDRC - International ...

    2016-08-12

    Aug 12, 2016 ... The issue LSLAs raise a number of concerns regarding compensation, including ... at a meeting with traders in Lamu, Kenya, where a new port is planned. ... compensation and a fair share of benefits and risks in land deals.

  16. Structuring competitive physician compensation models.

    Mobley, Kim; Turcotte, Claire

    2010-12-01

    When developing and reviewing their physician compensation programs, healthcare organizations should: Understand the market data. Test outcomes of incentive plans for fair market value. Check total compensation for fair market value and reasonableness.

  17. RELIABILITY OF LENTICULAR EXPANSION COMPENSATORS

    Gabriel BURLACU,

    2011-11-01

    Full Text Available Axial lenticular compensators are made to take over the longitudinal heat expansion, shock , vibration and noise, made elastic connections for piping systems. In order to have a long life for installations it is necessary that all elements, including lenticular compensators, have a good reliability. This desire can be did by technology of manufactoring and assembly of compensators, the material for lenses and by maintenance.of compensator

  18. Compensation for incoherent ground motion

    Shigeru, Takeda; Hiroshi, Matsumoto; Masakazu, Yoshioka; Yasunori, Takeuchi; Kikuo, Kudo; Tsuneya, Tsubokawa; Mitsuaki, Nozaki; Kiyotomo, Kawagoe

    1999-01-01

    The power spectrum density and coherence function for ground motions are studied for the construction of the next generation electron-positron linear collider. It should provide a center of mass energy between 500 GeV-1 TeV with luminosity as high as 10 33 to 10 34 cm -2 sec -1 . Since the linear collider has a relatively slow repetition rate, large number of particles and small sizes of the beam should be generated and preserved in the machine to obtain the required high luminosity. One of the most critical parameters is the extremely small vertical beam size at the interaction point, thus a proper alignment system for the focusing and accelerating elements of the machine is necessary to achieve the luminosity. We describe recent observed incoherent ground motions and an alignment system to compensate the distortion by the ground motions. (authors)

  19. Compensation Consultants and CEO Pay

    Kabir, Mohammed Rezaul; Minhat, Marizah

    2014-01-01

    The study examines the practice of employing multiple compensation consultants. Examining data of a sample of UK companies over the period 2003–2006 we find that CEOs receive higher equity-based pay when firms employ more than one compensation consultant. An increase in the number of compensation

  20. Without 'Focus'

    Aldo Sevi

    2010-12-01

    Full Text Available It is widely accepted that a notion of 'focus', more or less as conceived of in Jackendoff (1972, must be incorporated into our theory of grammar, as a means of accounting for certain observed correlations between prosodic facts and semantic/pragmatic facts. In this paper, we put forth the somewhat radical idea that the time has come to give up this customary view, and eliminate 'focus' from our theory of grammar. We argue that such a move is both economical and fruitful.Research over the years has revealed that the correlations between prosody, 'focus', and the alleged semantic/pragmatic effects of focus are much less clear and systematic than we may have initially hoped. First we argue that this state of affairs detracts significantly from the utility of our notion of 'focus', to the point of calling into question the very motivation for including it in the grammar. Then we look at some of the central data, and show how they might be analyzed without recourse to a notion of 'focus'. We concentrate on (i the effect of pitch accent placement on discourse congruence, and (ii the choice of 'associate' for the so-called 'focus sensitive' adverb only. We argue that our focus-free approach to the data improves empirical coverage, and begins to reveal patterns that have previously been obscured by preconceptions about 'focus'.ReferencesBeaver, D. & Clark, B. 2008. Sense and Sensitivity: How Focus Determines Meaning. Blackwell.Beaver, D., Clark, B., Flemming, E., Jaeger, T. F. & Wolters, M. 2007. ‘When semantics meets phonetics: Acoustical studies of second occurrence focus’. Language 83.2: 245–76.http://dx.doi.org/10.1353/lan.2007.0053Beckman, M. & Hirschberg, J. 1994. ‘The ToBI Annotation Conventions’. Ms.,http://www.cs.columbia.edu/~julia/files/conv.pdf.Bolinger, D. 1972. ‘Accent is predictable (if you are a mind-reader’. Language 48.3: 633–44.http://dx.doi.org/10.2307/412039Büring, D. 2006. ‘Focus projection and default

  1. Compensability index for compensation radiotherapy after treatment interruptions

    Putora, Paul Martin; Schmuecking, Michael; Aebersold, Daniel; Plasswilm, Ludwig

    2012-01-01

    The goal of our work was to develop a simple method to evaluate a compensation treatment after unplanned treatment interruptions with respect to their tumour- and normal tissue effect. We developed a software tool in java programming language based on existing recommendations to compensate for treatment interruptions. In order to express and visualize the deviations from the originally planned tumour and normal tissue effects we defined the compensability index. The compensability index represents an evaluation of the suitability of compensatory radiotherapy in a single number based on the number of days used for compensation and the preference of preserving the originally planned tumour effect or not exceeding the originally planned normal tissue effect. An automated tool provides a method for quick evaluation of compensation treatments. The compensability index calculation may serve as a decision support system based on existing and established recommendations

  2. Compensability index for compensation radiotherapy after treatment interruptions

    Putora Paul

    2012-12-01

    Full Text Available Abstract Background The goal of our work was to develop a simple method to evaluate a compensation treatment after unplanned treatment interruptions with respect to their tumour- and normal tissue effect. Methods We developed a software tool in java programming language based on existing recommendations to compensate for treatment interruptions. In order to express and visualize the deviations from the originally planned tumour and normal tissue effects we defined the compensability index. Results The compensability index represents an evaluation of the suitability of compensatory radiotherapy in a single number based on the number of days used for compensation and the preference of preserving the originally planned tumour effect or not exceeding the originally planned normal tissue effect. An automated tool provides a method for quick evaluation of compensation treatments. Conclusions The compensability index calculation may serve as a decision support system based on existing and established recommendations.

  3. Split and Compensated Hyperfine Fields in Magnetic Metal Clusters

    Nakamura, H.; Chudo, H.; Shiga, M.; Kohara, T.

    2004-01-01

    As prominent characteristics of magnetic metal cluster found in vanadium sulfides, we point out marked separation and compensation of the hyperfine field at the nuclear site; these are in somewhat discordance with the common sense for 3d transition-metal magnets, where the on-site isotropic field, scaling the ordered moment magnitude, is dominant.

  4. Smart Sensing Using Wavelets Project

    National Aeronautics and Space Administration — Further refinements to the FOSS technologies are focusing on “smart” sensing techniques that adjust sensing parameters as needed in real time so that...

  5. Fukushima: liability and compensation

    Vasquez-Maignan, Ximena

    2012-01-01

    On 11 March 2011, Japan endured one of the worst natural disasters in its history when a massive earthquake struck the Pacific coast of the country and was followed by a tsunami which led to considerable loss of lives. It also led to a major accident at the Fukushima Daiichi nuclear power plant. Soon afterwards, the operator of the plant, Tokyo Electric Power Company (TEPCO), assumed responsibility and liability for the nuclear accident. On 28 April 2011, TEPCO established a dedicated contact line to provide consulting services for financial compensation related to the damage caused

  6. Focused Science Delivery makes science make sense.

    Rachel W. Scheuering; Jamie. Barbour

    2004-01-01

    Science does not exist in a vacuum, but reading scientific publications might make you think it does. Although the policy and management implications of their findings could often touch a much wider audience, many scientists write only for the few people in the world who share their area of expertise. In addition, most scientific publications provide information that...

  7. On techniques for angle compensation in nonideal iris recognition.

    Schuckers, Stephanie A C; Schmid, Natalia A; Abhyankar, Aditya; Dorairaj, Vivekanand; Boyce, Christopher K; Hornak, Lawrence A

    2007-10-01

    The popularity of the iris biometric has grown considerably over the past two to three years. Most research has been focused on the development of new iris processing and recognition algorithms for frontal view iris images. However, a few challenging directions in iris research have been identified, including processing of a nonideal iris and iris at a distance. In this paper, we describe two nonideal iris recognition systems and analyze their performance. The word "nonideal" is used in the sense of compensating for off-angle occluded iris images. The system is designed to process nonideal iris images in two steps: 1) compensation for off-angle gaze direction and 2) processing and encoding of the rotated iris image. Two approaches are presented to account for angular variations in the iris images. In the first approach, we use Daugman's integrodifferential operator as an objective function to estimate the gaze direction. After the angle is estimated, the off-angle iris image undergoes geometric transformations involving the estimated angle and is further processed as if it were a frontal view image. The encoding technique developed for a frontal image is based on the application of the global independent component analysis. The second approach uses an angular deformation calibration model. The angular deformations are modeled, and calibration parameters are calculated. The proposed method consists of a closed-form solution, followed by an iterative optimization procedure. The images are projected on the plane closest to the base calibrated plane. Biorthogonal wavelets are used for encoding to perform iris recognition. We use a special dataset of the off-angle iris images to quantify the performance of the designed systems. A series of receiver operating characteristics demonstrate various effects on the performance of the nonideal-iris-based recognition system.

  8. Whiplash and the compensation hypothesis.

    Spearing, Natalie M; Connelly, Luke B

    2011-12-01

    Review article. To explain why the evidence that compensation-related factors lead to worse health outcomes is not compelling, either in general, or in the specific case of whiplash. There is a common view that compensation-related factors lead to worse health outcomes ("the compensation hypothesis"), despite the presence of important, and unresolved sources of bias. The empirical evidence on this question has ramifications for the design of compensation schemes. Using studies on whiplash, this article outlines the methodological problems that impede attempts to confirm or refute the compensation hypothesis. Compensation studies are prone to measurement bias, reverse causation bias, and selection bias. Errors in measurement are largely due to the latent nature of whiplash injuries and health itself, a lack of clarity over the unit of measurement (specific factors, or "compensation"), and a lack of appreciation for the heterogeneous qualities of compensation-related factors and schemes. There has been a failure to acknowledge and empirically address reverse causation bias, or the likelihood that poor health influences the decision to pursue compensation: it is unclear if compensation is a cause or a consequence of poor health, or both. Finally, unresolved selection bias (and hence, confounding) is evident in longitudinal studies and natural experiments. In both cases, between-group differences have not been addressed convincingly. The nature of the relationship between compensation-related factors and health is unclear. Current approaches to testing the compensation hypothesis are prone to several important sources of bias, which compromise the validity of their results. Methods that explicitly test the hypothesis and establish whether or not a causal relationship exists between compensation factors and prolonged whiplash symptoms are needed in future studies.

  9. Hyperspectral remote sensing

    Eismann, Michael Theodore

    2012-01-01

    ..., and hyperspectral data processing. While there are many resources that suitably cover these areas individually and focus on specific aspects of the hyperspectral remote sensing field, this book provides a holistic treatment...

  10. Temperature compensated photovoltaic array

    Mosher, Dan Michael

    1997-11-18

    A temperature compensated photovoltaic module (20) comprised of a series of solar cells (22) having a thermally activated switch (24) connected in parallel with several of the cells (22). The photovoltaic module (20) is adapted to charge conventional batteries having a temperature coefficient (TC) differing from the temperature coefficient (TC) of the module (20). The calibration temperatures of the switches (24) are chosen whereby the colder the ambient temperature for the module (20), the more switches that are on and form a closed circuit to short the associated solar cells (22). By shorting some of the solar cells (22) as the ambient temperature decreases, the battery being charged by the module (20) is not excessively overcharged at lower temperatures. PV module (20) is an integrated solution that is reliable and inexpensive.

  11. Dynamic Uncertainty for Compensated Second-Order Systems

    Clemens Elster

    2010-08-01

    Full Text Available The compensation of LTI systems and the evaluation of the according uncertainty is of growing interest in metrology. Uncertainty evaluation in metrology ought to follow specific guidelines, and recently two corresponding uncertainty evaluation schemes have been proposed for FIR and IIR filtering. We employ these schemes to compare an FIR and an IIR approach for compensating a second-order LTI system which has relevance in metrology. Our results suggest that the FIR approach is superior in the sense that it yields significantly smaller uncertainties when real-time evaluation of uncertainties is desired.

  12. Preferences, comparative advantage, and compensating wage differentials for job routinization

    Climent Quintana Domeque

    2010-01-01

    In this paper I attempt to explain why labor economists typically have not been able to find much evidence on compensating wage differentials for job disamenities, except for risk of death. The key insight here is that, although workers need to be compensated when their preferences do not match the requirements for performing a job task, the occurrence of mismatch also decreases productivity, reducing the surplus to be divided between workers and firms, and decreasing wages. I focus on the ma...

  13. Doppler Shift Compensation Schemes in VANETs

    F. Nyongesa

    2015-01-01

    Full Text Available Over the last decade vehicle-to-vehicle (V2V communication has received a lot of attention as it is a crucial issue in intravehicle communication as well as in Intelligent Transportation System (ITS. In ITS the focus is placed on integration of communication between mobile and fixed infrastructure to execute road safety as well as nonsafety information dissemination. The safety application such as emergence alerts lays emphasis on low-latency packet delivery rate (PDR, whereas multimedia and infotainment call for high data rates at low bit error rate (BER. The nonsafety information includes multimedia streaming for traffic information and infotainment applications such as playing audio content, utilizing navigation for driving, and accessing Internet. A lot of vehicular ad hoc network (VANET research has focused on specific areas including channel multiplexing, antenna diversity, and Doppler shift compensation schemes in an attempt to optimize BER performance. Despite this effort few surveys have been conducted to highlight the state-of-the-art collection on Doppler shift compensation schemes. Driven by this cause we survey some of the recent research activities in Doppler shift compensation schemes and highlight challenges and solutions as a stock-taking exercise. Moreover, we present open issues to be further investigated in order to address the challenges of Doppler shift in VANETs.

  14. Takeovers and (Excess) CEO Compensation

    Feito Ruiz, Isabel; Renneboog, Luc

    2017-01-01

    We study if a CEO’s equity-based compensation affects the expected value generation in takeovers. When the objectives of management and shareholders are more aligned, as proxied by the use of equity-based compensation, more value-maximizing acquisitions are expected. Whereas in widely-held firms the

  15. Takeovers and (excess) CEO compensation

    Feito Ruiz, Isabel; Renneboog, Luc

    We study if a CEO’s equity-based compensation affects the expected value generation in takeovers. When the objectives of management and shareholders are more aligned, as proxied by the use of equity-based compensation, more value-maximizing acquisitions are expected. Whereas in widely-held firms the

  16. Changing Conceptions of Employee Compensation

    Dixon, Mark R.; Hayes, Linda J.

    2004-01-01

    This paper reviews and discusses many differing forms of incentive compensation systems that are being used in today's organizations. The review traces the roots of bonus compensation from individual piece-work plans through the adoption of organization-wide gain sharing plans to the growing recognition of open-book management. Reasons for the…

  17. Motion compensation via redundant-wavelet multihypothesis.

    Fowler, James E; Cui, Suxia; Wang, Yonghui

    2006-10-01

    Multihypothesis motion compensation has been widely used in video coding with previous attention focused on techniques employing predictions that are diverse spatially or temporally. In this paper, the multihypothesis concept is extended into the transform domain by using a redundant wavelet transform to produce multiple predictions that are diverse in transform phase. The corresponding multiple-phase inverse transform implicitly combines the phase-diverse predictions into a single spatial-domain prediction for motion compensation. The performance advantage of this redundant-wavelet-multihypothesis approach is investigated analytically, invoking the fact that the multiple-phase inverse involves a projection that significantly reduces the power of a dense-motion residual modeled as additive noise. The analysis shows that redundant-wavelet multihypothesis is capable of up to a 7-dB reduction in prediction-residual variance over an equivalent single-phase, single-hypothesis approach. Experimental results substantiate the performance advantage for a block-based implementation.

  18. Compensated pulsed alternator

    Weldon, W.F.; Driga, M.D.; Woodson, H.H.

    1980-01-01

    This invention relates to an electromechanical energy converter with inertial energy storage. The device, a single phase, two or multi-pole alternator with stationary field coils, and a rotating armature is provided. The rotor itself may be of laminated steel for slower pulses or for faster pulses should be nonmagnetic and electrically nonconductive in order to allow rapid penetration of the field as the armature coil rotates. The armature coil comprises a plurality of power generating conductors mounted on the rotor. The alternator may also include a stationary or counterrotating compensating coil to increase the output voltage thereof and to reduce the internal impedance of the alternator at the moment of peak output. As the machine voltage rises sinusoidally, an external trigger switch is adapted to be closed at the appropriate time to create the desired output current from said alternator to an external load circuit, and as the output current passes through zero a self-commutating effect is provided to allow the switch to disconnect the generator from the external circuit

  19. Stabilized thermally compensated mirror

    Dunn, C. III; Tobin, R.D.; Bergstreser, N.E.; Heinz, T.A.

    1975-01-01

    A thermally compensated mirror is described that is formed by a laminated structure. The structure is comprised of a front plate having a reflective front surface and having a plurality of grooves formed in the rear surface for conducting coolant fluid in heat exchanging relation with said reflective surface, a rear plate having coolant inlet and coolant outlet openings extending therethrough, a minimum temperature plate interposed between said front and rear plates and formed with a plurality of coolant distribution passageways coupled to receive coolant fluid from said coolant inlet and oriented to distribute said coolant fluid in a manner to establish a minimum temperature plane parallel to said reflective surface, a temperature stabilization plate interposed between said front plate and said minimum temperature plate and formed with a plurality of coolant distribution channels coupled to receive said coolant fluid after said coolant fluid has passed in heat exchanging relation with said reflective surface and oriented to distribute said coolant fluid in a manner to establish a uniform temperature plane parallel to said reflective surface, and means for circulating said coolant fluid through said structure in a predetermined path. (U.S.)

  20. Transponder-aided joint calibration and synchronization compensation for distributed radar systems.

    Wang, Wen-Qin

    2015-01-01

    High-precision radiometric calibration and synchronization compensation must be provided for distributed radar system due to separate transmitters and receivers. This paper proposes a transponder-aided joint radiometric calibration, motion compensation and synchronization for distributed radar remote sensing. As the transponder signal can be separated from the normal radar returns, it is used to calibrate the distributed radar for radiometry. Meanwhile, the distributed radar motion compensation and synchronization compensation algorithms are presented by utilizing the transponder signals. This method requires no hardware modifications to both the normal radar transmitter and receiver and no change to the operating pulse repetition frequency (PRF). The distributed radar radiometric calibration and synchronization compensation require only one transponder, but the motion compensation requires six transponders because there are six independent variables in the distributed radar geometry. Furthermore, a maximum likelihood method is used to estimate the transponder signal parameters. The proposed methods are verified by simulation results.

  1. [Vestibular compensation studies]. [Vestibular Compensation and Morphological Studies

    Perachio, Adrian A. (Principal Investigator)

    1996-01-01

    The following topics are reported: neurophysiological studies on MVN neurons during vestibular compensation; effects of spinal cord lesions on VNC neurons during compensation; a closed-loop vestibular compensation model for horizontally canal-related MVN neurons; spatiotemporal convergence in VNC neurons; contributions of irregularly firing vestibular afferents to linear and angular VOR's; application to flight studies; metabolic measures in vestibular neurons; immediate early gene expression following vestibular stimulation; morphological studies on primary afferents, central vestibular pathways, vestibular efferent projection to the vestibular end organs, and three-dimensional morphometry and imaging.

  2. Skew quad compensation at PEP

    Murray, J.J.

    1977-10-01

    Rotational and focal effects of solenoids used in PEP detectors will cause severe perturbations of machine beam optics and must be corrected. Ordinarily this would be accomplished by the addition of compensating solenoids and adjustment of insertion quadrupole strengths. It has been found that an arbitrary cross plane coupling representing the effects of solenoids and/or skew quads in any combination can be synthesized (or compensated) exactly using a quartet of skew quads combined with other erect transport elements in a wide variety of configurations. Specific skew quad compensating systems for PEP have been designed and are under study by PEP staff. So far no fundamental flaws have been discovered. In view of that, PEP management has tentatively authorized the use of such a system in the PEP-4, PEP-9 experiments and proposes to leave the question open ''without prejudice'' for other experiments. Use of skew quad compensation involves an imponderable risk, of course, simply because the method is new and untested. But in addition to providing the only known method for dealing with skew quad perturbations, skew quad compensation, as an alternate to compensating solenoids, promises to be much cheaper, to require much less power and to occupy much less space in the IR's. The purpose of this note is to inform potential users of the foregoing situation and to explain skew quad compensation more fully. 2 refs., 1 fig., 1 tab

  3. A primer for workers' compensation.

    Bible, Jesse E; Spengler, Dan M; Mir, Hassan R

    2014-07-01

    A physician's role within a workers' compensation injury extends far beyond just evaluation and treatment with several socioeconomic and psychological factors at play compared with similar injuries occurring outside of the workplace. Although workers' compensation statutes vary among states, all have several basic features with the overall goal of returning the injured worker to maximal function in the shortest time period, with the least residual disability and shortest time away from work. To help physicians unfamiliar with the workers' compensation process accomplish these goals. Review. Educational review. The streamlined review addresses the topics of why is workers' compensation necessary; what does workers' compensation cover; progression after work injury; impairment and maximum medical improvement, including how to use the sixth edition of American Medical Association's (AMA) Guides to the evaluation of permanent impairment (Guides); completion of work injury claim after impairment rating; independent medical evaluation; and causation. In the "no-fault" workers' compensation system, physicians play a key role in progressing the claim along and, more importantly, getting the injured worker back to work as soon as safely possible. Physicians should remain familiar with the workers' compensation process, along with how to properly use the AMA Guides. Copyright © 2014 Elsevier Inc. All rights reserved.

  4. An effective temperature compensation approach for ultrasonic hydrogen sensors

    Tan, Xiaolong; Li, Min; Arsad, Norhana; Wen, Xiaoyan; Lu, Haifei

    2018-03-01

    Hydrogen is a kind of promising clean energy resource with a wide application prospect, which will, however, cause a serious security issue upon the leakage of hydrogen gas. The measurement of its concentration is of great significance. In a traditional approach of ultrasonic hydrogen sensing, a temperature drift of 0.1 °C results in a concentration error of about 250 ppm, which is intolerable for trace amount of gas sensing. In order to eliminate the influence brought by temperature drift, we propose a feasible approach named as linear compensation algorithm, which utilizes the linear relationship between the pulse count and temperature to compensate for the pulse count error (ΔN) caused by temperature drift. Experimental results demonstrate that our proposed approach is capable of improving the measurement accuracy and can easily detect sub-100 ppm of hydrogen concentration under variable temperature conditions.

  5. Altitude Compensating Nozzle

    Ruf, Joseph H.; Jones, Daniel

    2015-01-01

    The dual-bell nozzle (fig. 1) is an altitude-compensating nozzle that has an inner contour consisting of two overlapped bells. At low altitudes, the dual-bell nozzle operates in mode 1, only utilizing the smaller, first bell of the nozzle. In mode 1, the nozzle flow separates from the wall at the inflection point between the two bell contours. As the vehicle reaches higher altitudes, the dual-bell nozzle flow transitions to mode 2, to flow full into the second, larger bell. This dual-mode operation allows near optimal expansion at two altitudes, enabling a higher mission average specific impulse (Isp) relative to that of a conventional, single-bell nozzle. Dual-bell nozzles have been studied analytically and subscale nozzle tests have been completed.1 This higher mission averaged Isp can provide up to a 5% increase2 in payload to orbit for existing launch vehicles. The next important step for the dual-bell nozzle is to confirm its potential in a relevant flight environment. Toward this end, NASA Marshall Space Flight Center (MSFC) and Armstrong Flight Research Center (AFRC) have been working to develop a subscale, hot-fire, dual-bell nozzle test article for flight testing on AFRC's F15-D flight test bed (figs. 2 and 3). Flight test data demonstrating a dual-bell ability to control the mode transition and result in a sufficient increase in a rocket's mission averaged Isp should help convince the launch service providers that the dual-bell nozzle would provide a return on the required investment to bring a dual-bell into flight operation. The Game Changing Department provided 0.2 FTE to ER42 for this effort in 2014.

  6. What Constitutes Fair Compensation for Unfair Dismissal

    user

    Generally the monetary compensation is perceived to be a solatium. 19 .... compensation for non-patrimonial loss in the context of an unfair labour practice. 41 .... awards of compensation where a person's dignity is impaired in the course of an.

  7. Compensation in Swedish infrastructure projects and suggestions on policy improvements

    Jesper Persson

    2015-07-01

    Full Text Available Environmental compensation includes a range of activities intended to counterbalance such negative impacts of development projects that remain in the environment after all preventive and corrective measures have been fully implemented. Sweden, being a member state of the European Union (EU, must implement environmental compensation under EU directives such as the Habitat Directive. However, like in other countries, implementation is not yet widespread in Sweden, and new practices and guidelines remain to be developed both nationally and at European level. This need is all the more urgent considering that the European Commission estimates that, within the EU, about 100,000 hectares of land is converted from its natural state each year. The aim of this paper is to describe current environmental-compensation practices in Swedish road and railway projects and to discuss issues of vital importance to the development of compensation policy, such as what to compensate for, how much, and how. A national inventory was performed, for the first time in Sweden, to identify compensation measures in road and railway projects. Data were collected from a national mailing list including 141 officials at county administrative boards (CABs, internal e-mail correspondence within the Swedish Transport Administration and databases of court decisions. The inventory focused on compensation measures ordered by virtue of the Swedish Environmental Code. In addition, two case studies were carried out to investigate the planning of compensation measures. The results showed that CABs and courts rarely order compensation in infrastructure projects, even though this is possible under Swedish law. Between 1999 and 2012, 37 cases (i.e. permits issued were found for which compensation was ordered. Of these cases, 76% concerned compensation for encroachments on minor habitats such as small ponds and cairns. No CAB ordered compensation for non-protected areas. Compensation ratios

  8. Ecological compensation: From general guidance and expertise to specific proposals for road developments

    Villarroya, Ana; Persson, Jesper; Puig, Jordi

    2014-01-01

    The main scientific bibliography addressing the rationale behind ecological compensation is reviewed in order to examine general guidelines. This contains interesting general guidance on how to implement compensation, and provides the basis for future developments in compensation practice. On this basis, we propose a further step in compensation practice, advancing compensation proposals or rules for specific kinds of projects and contexts, focusing on road projects in the Spanish Environmental Impact Assessment (EIA). Three main residual impacts of roads are identified which usually remain uncompensated for: the loss of natural and semi-natural land use, the increase in emissions resulting from any new road, and the fragmentation, severance or barrier effect on the landscape and its wildlife. To counteract these, four proposals, or “rules”, are advanced: conservation of natural and semi-natural land use area, conservation of dominant plant species physiognomy, compensation for emissions, and the rule of positive defragmentation. -- Highlights: • Ecological compensation theory does not specify guidelines for types of projects. • EIA practitioners lack valuable specific guidance on how to implement compensation. • Specific guidance for road project ecological compensation is proposed. • Compensation proposals should have in mind present-day compensation practice level. • Specific ways to compensate for habitat loss, emissions, and fragmentation are shown

  9. Ecological compensation: From general guidance and expertise to specific proposals for road developments

    Villarroya, Ana, E-mail: avillarroya@alumni.unav.es [Department of Zoology and Ecology, University of Navarra, c/Irunlarrea s/n, 31008 Pamplona, Navarra (Spain); Persson, Jesper, E-mail: jesper.persson@slu.se [Department of Landscape Management, Design and Construction, Swedish University of Agricultural Sciences (SLU), P.O. Box 66, SE-230 53 Alnarp (Sweden); Puig, Jordi, E-mail: jpbaguer@unav.es [Department of Zoology and Ecology, University of Navarra, c/Irunlarrea s/n, 31008 Pamplona, Navarra (Spain)

    2014-02-15

    The main scientific bibliography addressing the rationale behind ecological compensation is reviewed in order to examine general guidelines. This contains interesting general guidance on how to implement compensation, and provides the basis for future developments in compensation practice. On this basis, we propose a further step in compensation practice, advancing compensation proposals or rules for specific kinds of projects and contexts, focusing on road projects in the Spanish Environmental Impact Assessment (EIA). Three main residual impacts of roads are identified which usually remain uncompensated for: the loss of natural and semi-natural land use, the increase in emissions resulting from any new road, and the fragmentation, severance or barrier effect on the landscape and its wildlife. To counteract these, four proposals, or “rules”, are advanced: conservation of natural and semi-natural land use area, conservation of dominant plant species physiognomy, compensation for emissions, and the rule of positive defragmentation. -- Highlights: • Ecological compensation theory does not specify guidelines for types of projects. • EIA practitioners lack valuable specific guidance on how to implement compensation. • Specific guidance for road project ecological compensation is proposed. • Compensation proposals should have in mind present-day compensation practice level. • Specific ways to compensate for habitat loss, emissions, and fragmentation are shown.

  10. Compensative hypertrophy of the kidney

    Raynaud, C.

    1976-01-01

    Several measurement methods are available to practitioners to reveal a compensative hypertrophy. Mensuration of the kidney has the advantage of simplicity but is in fact an unreliable and inaccurate method. Separate clearances in their traditional form have never entered into routine use because of the disadvantages of ureteral catheterism. The use of radioactive tracers avoids this drawback, but clearances calculated in this way are only valid in the absence of obstructive urinary disorders. Solutions have been proposed, but the values obtained are no longer identical with the clearances. The Hg uptake test quantifies quite accurately the function of each kidney. From the results obtained a complete compensative hypertrophy developed on a healthy kidney and an incomplete compensative hypertrophy developed on the diseased kidney have been described. In each of these situations the degree to which compensative hypertrophy develops seems to be fixed at a given level peculiar to each patient [fr

  11. Focusing ethnography

    Woermann, Niklas

    2018-01-01

    underpinnings of focusing ethnographic research by comparing different schools of thought and suggesting a practice theory-based approach. It argues that many research projects are focused but do not reflect on the process of focusing, describes how to identify focal settings or practices, and introduces......Building theory with ethnography and filmic research increasingly requires focussing on key practices or settings, instead of painting a broad panorama of a culture. But few authors discuss why and how to focus. This article provides a systematic discussion of the theoretical and methodological...

  12. CEO Compensation and Disclosure Policy

    Zhang, Weijia; Zhang, Kun

    2016-01-01

    This paper examines the relationship between CEO compensation and disclosure policy related to corporate governance information within S&P 500 index. Our sample consists of 456 companies for the period from 2005 to 2015. Most previous researchers mainly put their attention on various corporate governance characteristics such as board size, board independence, and executive ownership when analysing CEO compensation. Our paper extends the previous study by dividing corporate governance into...

  13. Temperature Compensated Strain Sensor Based on Cascaded Sagnac Interferometers and All-Solid Birefringent Hybrid Photonic Crystal Fibers

    Gu, Bobo; Yuan, Wu; He, Sailing

    2012-01-01

    We demonstrate a temperature compensated strain sensor with two cascaded Sagnac interferometers, that provide strain sensing and temperature compensation, respectively. The Sagnac interferometers use an all-solid hybrid photonic crystal fiber with stress-induced birefringence. The stress-induced ...

  14. More than just the mean: moving to a dynamic view of performance-based compensation.

    Barnes, Christopher M; Reb, Jochen; Ang, Dionysius

    2012-05-01

    Compensation decisions have important consequences for employees and organizations and affect factors such as retention, motivation, and recruitment. Past research has primarily focused on mean performance as a predictor of compensation, promoting the implicit assumption that alternative aspects of dynamic performance are not relevant. To address this gap in the literature, we examined the influence of dynamic performance characteristics on compensation decisions in the National Basketball Association (NBA). We predicted that, in addition to performance mean, performance trend and variability would also affect compensation decisions. Results revealed that performance mean and trend, but not variability, were significantly and positively related to changes in compensation levels of NBA players. Moreover, trend (but not mean or variability) predicted compensation when controlling for future performance, suggesting that organizations overweighted trend in their compensation decisions. Theoretical and practical implications are discussed. (PsycINFO Database Record (c) 2012 APA, all rights reserved).

  15. Focused Ethnography

    Hubert Knoblauch

    2005-09-01

    Full Text Available In this paper I focus on a distinctive kind of sociological ethnography which is particularly, though not exclusively, adopted in applied research. It has been proposed that this branch of ethno­graphy be referred to as focused ethnography. Focused ethnography shall be delineated within the context of other common conceptions of what may be called conventional ethnography. However, rather than being opposed to it, focused ethno­graphy is rather complementary to conventional ethnography, particularly in fields that are charac­teristic of socially and functionally differentiated contemporary society. The paper outlines the back­ground as well as the major methodological features of focused ethnography, such as short-term field visits, data intensity and time intensity, so as to provide a background for future studies in this area. URN: urn:nbn:de:0114-fqs0503440

  16. Remote Sensing

    Khorram, Siamak; Koch, Frank H; van der Wiele, Cynthia F

    2012-01-01

    Remote Sensing provides information on how remote sensing relates to the natural resources inventory, management, and monitoring, as well as environmental concerns. It explains the role of this new technology in current global challenges. "Remote Sensing" will discuss remotely sensed data application payloads and platforms, along with the methodologies involving image processing techniques as applied to remotely sensed data. This title provides information on image classification techniques and image registration, data integration, and data fusion techniques. How this technology applies to natural resources and environmental concerns will also be discussed.

  17. High order dark wavefront sensing simulations

    Ragazzoni, Roberto; Arcidiacono, Carmelo; Farinato, Jacopo; Viotto, Valentina; Bergomi, Maria; Dima, Marco; Magrin, Demetrio; Marafatto, Luca; Greggio, Davide; Carolo, Elena; Vassallo, Daniele

    2016-07-01

    Dark wavefront sensing takes shape following quantum mechanics concepts in which one is able to "see" an object in one path of a two-arm interferometer using an as low as desired amount of light actually "hitting" the occulting object. A theoretical way to achieve such a goal, but in the realm of wavefront sensing, is represented by a combination of two unequal beams interferometer sharing the same incoming light, and whose difference in path length is continuously adjusted in order to show different signals for different signs of the incoming perturbation. Furthermore, in order to obtain this in white light, the path difference should be properly adjusted vs the wavelength used. While we incidentally describe how this could be achieved in a true optomechanical setup, we focus our attention to the simulation of a hypothetical "perfect" dark wavefront sensor of this kind in which white light compensation is accomplished in a perfect manner and the gain is selectable in a numerical fashion. Although this would represent a sort of idealized dark wavefront sensor that would probably be hard to match in the real glass and metal, it would also give a firm indication of the maximum achievable gain or, in other words, of the prize for achieving such device. Details of how the simulation code works and first numerical results are outlined along with the perspective for an in-depth analysis of the performances and its extension to more realistic situations, including various sources of additional noise.

  18. 29 CFR 525.6 - Compensable time.

    2010-07-01

    ... 29 Labor 3 2010-07-01 2010-07-01 false Compensable time. 525.6 Section 525.6 Labor Regulations... WITH DISABILITIES UNDER SPECIAL CERTIFICATES § 525.6 Compensable time. Individuals employed subject to this part must be compensated for all hours worked. Compensable time includes not only those hours...

  19. 48 CFR 970.2270 - Unemployment compensation.

    2010-10-01

    ... 48 Federal Acquisition Regulations System 5 2010-10-01 2010-10-01 false Unemployment compensation... Unemployment compensation. (a) Each state has its own unemployment compensation system to provide payments to... unemployment compensation benefits through a payroll tax on employers. Most DOE contractors are subject to the...

  20. Motion-compensated processing of image signals

    2010-01-01

    In a motion-compensated processing of images, input images are down-scaled (scl) to obtain down-scaled images, the down-scaled images are subjected to motion- compensated processing (ME UPC) to obtain motion-compensated images, the motion- compensated images are up-scaled (sc2) to obtain up-scaled

  1. The Compensation and Benefits System: Private Companies vs. Budgetary System

    Aldea Bogdan

    2015-12-01

    Full Text Available The economic evolution of the last decades has entailed major changes concerning the Human Resource Management practices, in both private and budgetary sector of Romania. In order to maintain efficiency and market competitivity, a company must adapt to these changes by altering its human resource strategy since managers are encountering increasingly complex challenges as to attracting, motivating and retaining employees. Such an objective might be accomplished by elaborating a competitive system of employee compensation. This article focuses on the stage reached by the Human Resource Management in the compensation and benefits system of the private and budgetary sector. For the latter, we are focusing on the romanian system of higher education. This study demonstrates that the compensation and benefits system which is implemented in romanian universities is limited and can offer few opportunities as compared to the one implemented by private companies. It is worth saying that the legal system has a negative impact in this matter.

  2. The background factor of the driving compensation behavior among elderly drivers

    Usui, Shinnosuke; Taishi, Nozomi

    2016-01-01

    The purpose of this study is to examine what factors lead to driving compensation behavior among elderly drivers, particularly focusing on the effect of self-reported driving performance, and to investigate the relationship between driving compensation behavior and traffic accidents or violations. After analyzing 237 elderly drivers, the results showed that whereas self-reported driving performances influenced driving compensation behaviors, the relationship between self-reported driving perf...

  3. Real time drift measurement for colloidal probe atomic force microscope: a visual sensing approach

    Wang, Yuliang, E-mail: wangyuliang@buaa.edu.cn; Bi, Shusheng [Robotics Institute, School of Mechanical Engineering and Automation, Beihang University, Beijing 100191 (China); Wang, Huimin [Department of Materials Science and Engineering, The Ohio State University, 2041 College Rd., Columbus, OH 43210 (United States)

    2014-05-15

    Drift has long been an issue in atomic force microscope (AFM) systems and limits their ability to make long time period measurements. In this study, a new method is proposed to directly measure and compensate for the drift between AFM cantilevers and sample surfaces in AFM systems. This was achieved by simultaneously measuring z positions for beads at the end of an AFM colloidal probe and on sample surface through an off-focus image processing based visual sensing method. The working principle and system configuration are presented. Experiments were conducted to validate the real time drift measurement and compensation. The implication of the proposed method for regular AFM measurements is discussed. We believe that this technique provides a practical and efficient approach for AFM experiments requiring long time period measurement.

  4. A new quantitative model of ecological compensation based on ecosystem capital in Zhejiang Province, China*

    Jin, Yan; Huang, Jing-feng; Peng, Dai-liang

    2009-01-01

    Ecological compensation is becoming one of key and multidiscipline issues in the field of resources and environmental management. Considering the change relation between gross domestic product (GDP) and ecological capital (EC) based on remote sensing estimation, we construct a new quantitative estimate model for ecological compensation, using county as study unit, and determine standard value so as to evaluate ecological compensation from 2001 to 2004 in Zhejiang Province, China. Spatial differences of the ecological compensation were significant among all the counties or districts. This model fills up the gap in the field of quantitative evaluation of regional ecological compensation and provides a feasible way to reconcile the conflicts among benefits in the economic, social, and ecological sectors. PMID:19353749

  5. Compensation of propagation loss of surface plasmon polaritons with a finite-thickness dielectric gain layer

    Zhang, Xin; Liu, Haitao; Zhong, Ying

    2012-01-01

    We theoretically study the compensation of propagation loss of surface plasmon polaritons (SPPs) with the use of a finite-thickness dielectric layer with optical gain. The impacts of the gain coefficient, the gain-layer thickness and the wavelength on the loss compensation and the field distribution of the SPP mode are systematically explored with a fully vectorial method. Abnormal behaviors for the loss compensation as the gain-layer thickness increases are found and explained. Critical values of the gain coefficient and of the corresponding gain-layer thickness for just compensating the propagation loss are provided. Our results show that as the SPP propagation loss is fully compensated with a gain coefficient at a reasonably low level, the gain layer is still thin enough to ensure a large exterior SPP field at the gain-layer/air interface, which is important for achieving a strong light–matter interaction for applications such as bio-chemical sensing. (paper)

  6. Automatic Detection of Compensation During Robotic Stroke Rehabilitation Therapy.

    Zhi, Ying Xuan; Lukasik, Michelle; Li, Michael H; Dolatabadi, Elham; Wang, Rosalie H; Taati, Babak

    2018-01-01

    Robotic stroke rehabilitation therapy can greatly increase the efficiency of therapy delivery. However, when left unsupervised, users often compensate for limitations in affected muscles and joints by recruiting unaffected muscles and joints, leading to undesirable rehabilitation outcomes. This paper aims to develop a computer vision system that augments robotic stroke rehabilitation therapy by automatically detecting such compensatory motions. Nine stroke survivors and ten healthy adults participated in this study. All participants completed scripted motions using a table-top rehabilitation robot. The healthy participants also simulated three types of compensatory motions. The 3-D trajectories of upper body joint positions tracked over time were used for multiclass classification of postures. A support vector machine (SVM) classifier detected lean-forward compensation from healthy participants with excellent accuracy (AUC = 0.98, F1 = 0.82), followed by trunk-rotation compensation (AUC = 0.77, F1 = 0.57). Shoulder-elevation compensation was not well detected (AUC = 0.66, F1 = 0.07). A recurrent neural network (RNN) classifier, which encodes the temporal dependency of video frames, obtained similar results. In contrast, F1-scores in stroke survivors were low for all three compensations while using RNN: lean-forward compensation (AUC = 0.77, F1 = 0.17), trunk-rotation compensation (AUC = 0.81, F1 = 0.27), and shoulder-elevation compensation (AUC = 0.27, F1 = 0.07). The result was similar while using SVM. To improve detection accuracy for stroke survivors, future work should focus on predefining the range of motion, direct camera placement, delivering exercise intensity tantamount to that of real stroke therapies, adjusting seat height, and recording full therapy sessions.

  7. French academic's views on financial compensation of participants.

    Dualé, Christian; Breysse, Gaétan; Bories-Azeau, Béatrice; Cornu, Catherine

    2016-07-01

    Whether and how participants in biomedical research should receive financial compensation is debated. We wished to explore how this issue was perceived by French professionals, focusing on different conditions of research. We surveyed referent responders of Clinical Investigation Centres, Research Ethics Committees and hospital administrative departments for clinical research, via referent responders who completed an online questionnaire on behalf of their respective teams. Financial compensation was addressed in terms of general perception, justifications, interpretation of French law, concrete clinical situations and compensation of incurred expenses. Descriptive analyses and correlations were carried out based on scalar responses. The questionnaire was answered by 54/116 (45·6%) centres. The ethical aspects of compensation were viewed differently by Clinical Investigation Centres and Research Ethics Committees, whereas the practical aspects were viewed similarly. Agreement to compensation for patients was lower than for healthy volunteers (74·1 vs. 98·2%). The most frequently cited justifications for compensation apart from the inconveniences of research were the potential risk and the absence of medical benefit. Most of the proposed expenses incurred were to be compensated, but agreement to reimbursement of petrol bills or childcare expense was lower. Although some of the responses align with previous surveys in other countries, this information may help French professionals to harmonise their practices. We also addressed practical issues which could be studied in other European countries, for professionals and participants. Finally, the reluctance to compensate patients requires further study, taking into account welfare environment and consequences for recruitment. © 2016 Stichting European Society for Clinical Investigation Journal Foundation.

  8. Glucose Sensing

    Geddes, Chris D

    2006-01-01

    Topics in Fluorescence Spectroscopy, Glucose Sensing is the eleventh volume in the popular series Topics in Fluorescence Spectroscopy, edited by Drs. Chris D. Geddes and Joseph R. Lakowicz. This volume incorporates authoritative analytical fluorescence-based glucose sensing reviews specialized enough to be attractive to professional researchers, yet also appealing to the wider audience of scientists in related disciplines of fluorescence. Glucose Sensing is an essential reference for any lab working in the analytical fluorescence glucose sensing field. All academics, bench scientists, and industry professionals wishing to take advantage of the latest and greatest in the continuously emerging field of glucose sensing, and diabetes care & management, will find this volume an invaluable resource. Topics in Fluorescence Spectroscopy Volume 11, Glucose Sensing Chapters include: Implantable Sensors for Interstitial Fluid Smart Tattoo Glucose Sensors Optical Enzyme-based Glucose Biosensors Plasmonic Glucose Sens...

  9. Make Sense?

    Gyrd-Jones, Richard; Törmälä, Minna

    Purpose: An important part of how we sense a brand is how we make sense of a brand. Sense-making is naturally strongly connected to how we cognize about the brand. But sense-making is concerned with multiple forms of knowledge that arise from our interpretation of the brand-related stimuli......: Declarative, episodic, procedural and sensory. Knowledge is given meaning through mental association (Keller, 1993) and / or symbolic interaction (Blumer, 1969). These meanings are centrally related to individuals’ sense of identity or “identity needs” (Wallpach & Woodside, 2009). The way individuals make...... sense of brands is related to who people think they are in their context and this shapes what they enact and how they interpret the brand (Currie & Brown, 2003; Weick, Sutcliffe, & Obstfeld, 2005; Weick, 1993). Our subject of interest in this paper is how stakeholders interpret and ascribe meaning...

  10. Adaptive Motion Compensation in Radiotherapy

    Murphy, Martin J

    2011-01-01

    External-beam radiotherapy has long been challenged by the simple fact that patients can (and do) move during the delivery of radiation. Recent advances in imaging and beam delivery technologies have made the solution--adapting delivery to natural movement--a practical reality. Adaptive Motion Compensation in Radiotherapy provides the first detailed treatment of online interventional techniques for motion compensation radiotherapy. This authoritative book discusses: Each of the contributing elements of a motion-adaptive system, including target detection and tracking, beam adaptation, and pati

  11. Network compensation for missing sensors

    Ahumada, Albert J., Jr.; Mulligan, Jeffrey B.

    1991-01-01

    A network learning translation invariance algorithm to compute interpolation functions is presented. This algorithm with one fixed receptive field can construct a linear transformation compensating for gain changes, sensor position jitter, and sensor loss when there are enough remaining sensors to adequately sample the input images. However, when the images are undersampled and complete compensation is not possible, the algorithm need to be modified. For moderate sensor losses, the algorithm works if the transformation weight adjustment is restricted to the weights to output units affected by the loss.

  12. Energy compensation after sprint- and high-intensity interval training.

    Matthew M Schubert

    Full Text Available Many individuals lose less weight than expected in response to exercise interventions when considering the increased energy expenditure of exercise (ExEE. This is due to energy compensation in response to ExEE, which may include increases in energy intake (EI and decreases in non-exercise physical activity (NEPA. We examined the degree of energy compensation in healthy young men and women in response to interval training.Data were examined from a prior study in which 24 participants (mean age, BMI, & VO2max = 28 yrs, 27.7 kg•m-2, and 32 mL∙kg-1∙min-1 completed either 4 weeks of sprint-interval training or high-intensity interval training. Energy compensation was calculated from changes in body composition (air displacement plethysmography and exercise energy expenditure was calculated from mean heart rate based on the heart rate-VO2 relationship. Differences between high (≥ 100% and low (< 100% levels of energy compensation were assessed. Linear regressions were utilized to determine associations between energy compensation and ΔVO2max, ΔEI, ΔNEPA, and Δresting metabolic rate.Very large individual differences in energy compensation were noted. In comparison to individuals with low levels of compensation, individuals with high levels of energy compensation gained fat mass, lost fat-free mass, and had lower change scores for VO2max and NEPA. Linear regression results indicated that lower levels of energy compensation were associated with increases in ΔVO2max (p < 0.001 and ΔNEPA (p < 0.001.Considerable variation exists in response to short-term, low dose interval training. In agreement with prior work, increases in ΔVO2max and ΔNEPA were associated with lower energy compensation. Future studies should focus on identifying if a dose-response relationship for energy compensation exists in response to interval training, and what underlying mechanisms and participant traits contribute to the large variation between individuals.

  13. Incorporating the effects of lateral spread of the primary fluence, into compensator design

    Reece, P.J.; Hoban, P.

    2000-01-01

    Full text: In this study we extended ideas developed by Faddegon and Pfalzner on the construction of patient specific compensating filters. Their research was essentially focused on formulating a general method for creating compensators using a 3D planning system. In their work Faddegon and Pfalzner utilized a simple attenuation model to convert transmission arrays into filter thickness arrays. The compensators constructed from these arrays produce the primary fluence required to give a uniform dose distribution at a specified depth. This technique does not account for local geometric variations hi compensator scattering conditions. Therefore we have devised a method to incorporate the effects of lateral spread of the primary fluence passing through the compensating filter. A 2D Gaussian kernel, generated from Monte Carlo measurements, was used to model the spread of the primary fluence in the compensating filter. A 'maximum likelihood' optimisation algorithm was employed to deconvolve the kernel from the desired primary fluence to produce a more realistic incident fluence and compensator thickness array. The CMS FOCUS planning system was used to generate transmission maps corresponding to the desired influence of the compensating filter. Two compensating filters were constructed for each map, one using the standard attenuation method and the other with our method. For each method, an assessment was made using film dosimetry, on the degree of correlation between the desired primary fluence and the primary fluence produced by the compensating filter. Our results indicate that for compensating filters which are relatively uniform in thickness, there is good agreement between desired and delivered fluence maps for both methods. For non-uniform compensating filters the attenuation method deviates more notably from the desired fluence map. As expected, both methods also show significant deviations around the edges of the filter. It is anticipated that the work done here

  14. SU-E-T-357: Electronic Compensation Technique to Deliver Total Body Dose

    Lakeman, T [State University of New York at Buffalo, Buffalo, NY (United States); Wang, I; Podgorsak, M [State University of New York at Buffalo, Buffalo, NY (United States); Roswell Park Cancer Institute, Buffalo, NY (United States)

    2015-06-15

    Purpose: Total body irradiation (TBI) uses large parallel-opposed radiation fields to suppress the patient’s immune system and eradicate the residual cancer cells in preparation of recipient for bone marrow transplant. The manual placement of lead compensators has conventionally been used to compensate for the varying thickness through the entire body in large-field TBI. The goal of this study is to pursue utilizing the modern electronic compensation technique to more accurately and efficiently deliver dose to patients in need of TBI. Methods: Treatment plans utilizing electronic compensation to deliver a total body dose were created retrospectively for patients for whom CT data had been previously acquired. Each treatment plan includes two, specifically weighted, pair of opposed fields. One pair of open, large fields (collimator=45°), to encompass the patient’s entire anatomy, and one pair of smaller fields (collimator=0°) focused only on the thicker midsection of the patient. The optimal fluence for each one of the smaller fields was calculated at a patient specific penetration depth. Irregular surface compensators provide a more uniform dose distribution within the smaller opposed fields. Results: Dose-volume histograms (DVH) were calculated for the evaluating the electronic compensation technique. In one case, the maximum body doses calculated from the DVH were reduced from the non-compensated 195.8% to 165.3% in the electronically compensated plans, indicating a more uniform dose with the region of electronic compensation. The mean body doses calculated from the DVH were also reduced from the non-compensated 120.6% to 112.7% in the electronically compensated plans, indicating a more accurate delivery of the prescription dose. All calculated monitor units were well within clinically acceptable limits. Conclusion: Electronic compensation technique for TBI will not substantially increase the beam on time while it can significantly reduce the compensator

  15. Psychology of Pay and Compensation

    Thierry, Hk.; Smelser, N.J.; Baltes, P.B.

    2002-01-01

    In most industrialized countries the compensation, of managers and employees is structured along quite comparable patterns. One part consists of base pay, a second part of results-oriented pay, and a third part of secondary labor conditions. In many instances part four is composed of perquisites:

  16. Ongoing transients in carbonate compensation

    Boudreau, B.P.; Middelburg, J.J.; Hofmann, A.F.; Meysman, F.J.R.

    2010-01-01

    Uptake of anthropogenic CO2 is acidifying the oceans. Over the next 2000 years, this will modify the dissolution and preservation of sedimentary carbonate. By coupling new formulas for the positions of the calcite saturation horizon, zsat, the compensation depth, zcc, and the snowline, zsnow, to a

  17. Optimal compensation for neuron loss

    Barrett, David GT; Denève, Sophie; Machens, Christian K

    2016-01-01

    The brain has an impressive ability to withstand neural damage. Diseases that kill neurons can go unnoticed for years, and incomplete brain lesions or silencing of neurons often fail to produce any behavioral effect. How does the brain compensate for such damage, and what are the limits of this compensation? We propose that neural circuits instantly compensate for neuron loss, thereby preserving their function as much as possible. We show that this compensation can explain changes in tuning curves induced by neuron silencing across a variety of systems, including the primary visual cortex. We find that compensatory mechanisms can be implemented through the dynamics of networks with a tight balance of excitation and inhibition, without requiring synaptic plasticity. The limits of this compensatory mechanism are reached when excitation and inhibition become unbalanced, thereby demarcating a recovery boundary, where signal representation fails and where diseases may become symptomatic. DOI: http://dx.doi.org/10.7554/eLife.12454.001 PMID:27935480

  18. Synchrony - Cyberknife Respiratory Compensation Technology

    Ozhasoglu, Cihat; Saw, Cheng B.; Chen Hungcheng; Burton, Steven; Komanduri, Krishna; Yue, Ning J.; Huq, Saiful M.; Heron, Dwight E.

    2008-01-01

    Studies of organs in the thorax and abdomen have shown that these organs can move as much as 40 mm due to respiratory motion. Without compensation for this motion during the course of external beam radiation therapy, the dose coverage to target may be compromised. On the other hand, if compensation of this motion is by expansion of the margin around the target, a significant volume of normal tissue may be unnecessarily irradiated. In hypofractionated regimens, the issue of respiratory compensation becomes an important factor and is critical in single-fraction extracranial radiosurgery applications. CyberKnife is an image-guided radiosurgery system that consists of a 6-MV LINAC mounted to a robotic arm coupled through a control loop to a digital diagnostic x-ray imaging system. The robotic arm can point the beam anywhere in space with 6 degrees of freedom, without being constrained to a conventional isocenter. The CyberKnife has been recently upgraded with a real-time respiratory tracking and compensation system called Synchrony. Using external markers in conjunction with diagnostic x-ray images, Synchrony helps guide the robotic arm to move the radiation beam in real time such that the beam always remains aligned with the target. With the aid of Synchrony, the tumor motion can be tracked in three-dimensional space, and the motion-induced dosimetric change to target can be minimized with a limited margin. The working principles, advantages, limitations, and our clinical experience with this new technology will be discussed

  19. Material focus

    Sokoler, Tomas; Vallgårda, Anna K. A.

    2009-01-01

    In this paper we build on the notion of computational composites, which hold a material perspective on computational technology. We argue that a focus on the material aspects of the technology could be a fruitful approach to achieve new expressions and to gain a new view on the technology's role...... in design. We study two of the computer's material properties: computed causality and connectability and through developing two computational composites that utilize these properties we begin to explore their potential expressions....

  20. A hierarchic approach for examining panarctic vegeta0on with a focus on the linkages between remote-sensing and plot-based studies: A prototype example from Toolik Lake, Alaska

    Walker, D.A.; Bhatt, U.S.; Breen, A.L.

    A circumpolar view of Arctic vegetation developed with the advent of satellite-derived remote-sensing products. Interpretations of what the revealed patterns mean are dependent on a foundation of in-situ plot-based observations. Despite the importance of ground-based observations, only a few areas...... of species composition, canopy structure, biomass, leaf-area index, and NDVI, along with high-resolution satellite-based remote-sensing products at the same time....... classification, plot markings, and standardized approaches to describe the local environment, including photo points showing the vegetation and soils up close and in landscape view. (3) Standardized approaches for collecting in-situ time-series of spectral data. Standardized methods for collecting and analyzing...

  1. Plasma Focus

    Bernard, Alain; Jolas, Alain; Garconnet, J.-P.; Mascureau, J. de; Nazet, Christian; Coudeville, Alain; Bekiarian, Andre.

    1977-01-01

    The present report is the edition of the lectures given in a conference on the Focus experiment held at the Centre d'etudes de Limeil, on Oct. 1975. After a survey of the early laboratories one will find the main results obtained in Limeil concerning interferometry, laser scattering, electric and magnetic-measurements, X-ray and neutron emission and also the possible use of explosive current generators instead of capacitor banks at high energy levels. The principal lines of future research are given in the conclusion [fr

  2. Focus: Digital

    Technology has been an all-important and defining element within the arts throughout the 20th century, and it has fundamentally changed the ways in which we produce and consume music. With this Focus we investigate the latest developments in the digital domain – and their pervasiveness and rapid...... production and reception of contemporary music and sound art. With ‘Digital’ we present four composers' very different answers to how technology impact their work. To Juliana Hodkinson it has become an integral part of her sonic writing. Rudiger Meyer analyses the relationships between art and design and how...

  3. Instability of compensated beam-beam collisions

    Rosenzweig, J.B.; Autin, B.; Chen, Pisin.

    1989-01-01

    The beam-beam disruption phenomena in linear colliders are increasingly seen as a source of serious problems for these machines. A plasma compensation scheme, in which the motion of the plasma electrons in the presence of the colliding beams provides neutralizing charge and current densities, has been proposed and studied. But natural alternative to this scheme is to consider the overlapping of nearly identical high energy e + and e/sup /minus// bunches, and the collision of two such pairs - in other words, collision of two opposing relativistic positronium plasmas. It should be noticed that while the luminosity for all collisions is increased by a factor of four in this scheme, the event rate for e + e/sup /minus// collisions is only increased by a factor of two. The other factor of two corresponds to the addition of e + e + and e/sup /minus//e/sup /minus// collisions to the interaction point. This beam compensation scheme, which has been examined through computer simulation by Balakin and Solyak in the Soviet Union, promises full neutralization of beam charges and currents. These numerical investigations have shown that plasma instabilities exist in this nominally neutral system. Although the implementation of this idea seems technically daunting, the potential benefits (beamstrahlung and disruption suppression, relaxation of final focus system constraints) are such that we should consider the physics of these collisions further. In the remainder of this paper, we theoretically analyze the issues of stability and bunch parameter tolerances in this scheme. 11 refs

  4. Energy compensation after sprint- and high-intensity interval training.

    Schubert, Matthew M; Palumbo, Elyse; Seay, Rebekah F; Spain, Katie K; Clarke, Holly E

    2017-01-01

    Many individuals lose less weight than expected in response to exercise interventions when considering the increased energy expenditure of exercise (ExEE). This is due to energy compensation in response to ExEE, which may include increases in energy intake (EI) and decreases in non-exercise physical activity (NEPA). We examined the degree of energy compensation in healthy young men and women in response to interval training. Data were examined from a prior study in which 24 participants (mean age, BMI, & VO2max = 28 yrs, 27.7 kg•m-2, and 32 mL∙kg-1∙min-1) completed either 4 weeks of sprint-interval training or high-intensity interval training. Energy compensation was calculated from changes in body composition (air displacement plethysmography) and exercise energy expenditure was calculated from mean heart rate based on the heart rate-VO2 relationship. Differences between high (≥ 100%) and low (high levels of energy compensation gained fat mass, lost fat-free mass, and had lower change scores for VO2max and NEPA. Linear regression results indicated that lower levels of energy compensation were associated with increases in ΔVO2max (p interval training. In agreement with prior work, increases in ΔVO2max and ΔNEPA were associated with lower energy compensation. Future studies should focus on identifying if a dose-response relationship for energy compensation exists in response to interval training, and what underlying mechanisms and participant traits contribute to the large variation between individuals.

  5. Compensation of dogleg effect in Fermilab Booster

    Xiao Biao Huang

    2003-01-01

    The edge focusing of dogleg magnets in Fermilab Booster has been causing severe distortion to the horizontal linear optics. The doglegs are vertical rectangular bends, therefore the vertical edge focusing is canceled by body focusing and the overall effect is focusing in the horizontal plane. The maximum horizontal beta function is changed from 7m to 46.9m and maximum dispersion from 3.19m to 6.14m. Beam size increases accordingly. This is believed to be one of the major reasons of beam loss. In this technote we demonstrate that this effect can be effectively corrected with Booster's quadrupole correctors in short straight sections (QS). There are 24 QS correctors which can alter horizontal linear optics with negligible perturbation to the vertical plane. The currents of correctors are determined by harmonic compensation, i.e., cancellation of dogleg's harmonics that are responsible for the distortion with that of QS correctors. By considering a few leading harmonics, the ideal lattice can be partly restored....

  6. Environmental radiation sensing technologies

    Nishizawa, Hiroshi; Inomata, Kenji; Tamuro, Masaru; Fujita, Kazuhiko

    2013-01-01

    After the Fukushima nuclear accident, environmental radiation monitoring and radioactivity measurement of contamination of wastes, soils, food and drinking water were needed in accurate and reliable way. Based on radiation sensing technologies and radiation and light coupled analysis method, new environmental radiation measurement system for simple monitoring post without exclusive house and also portable monitoring post for temporary use were developed with low cost. Measurement accuracy was improved by real-time processing of detected pulses and corrected non-linearity of low-energy range by analysis. Environmental performance was upgraded to assure detector gain with compensated against temperature change and aging. Inspection and maintenance were also simplified using touch panel display with standardized application menu and data format. (T. Tanaka)

  7. Compressive sensing for urban radar

    Amin, Moeness

    2014-01-01

    With the emergence of compressive sensing and sparse signal reconstruction, approaches to urban radar have shifted toward relaxed constraints on signal sampling schemes in time and space, and to effectively address logistic difficulties in data acquisition. Traditionally, these challenges have hindered high resolution imaging by restricting both bandwidth and aperture, and by imposing uniformity and bounds on sampling rates.Compressive Sensing for Urban Radar is the first book to focus on a hybrid of two key areas: compressive sensing and urban sensing. It explains how reliable imaging, tracki

  8. 33 CFR 136.223 - Compensation allowable.

    2010-07-01

    ...) MARINE POLLUTION FINANCIAL RESPONSIBILITY AND COMPENSATION OIL SPILL LIABILITY TRUST FUND; CLAIMS... allowable under paragraph (a) of this section must be reduced by— (1) All compensation made available to the... under § 136.235. Government Revenues ...

  9. Nuclear damage compensation and energy reform

    Yokemoto, Masafumi

    2013-01-01

    Nuclear damage compensation and energy reform were closely related. Nuclear damage compensation cost should be part of generation cost of nuclear power. Extend of nuclear damage compensation was limited by compensation standard of Tokyo Electric Power Co. (TEPCO) following guidelines of Dispute Reconciliation Committee for Nuclear Damage Compensation. TEPCO had already paid compensation of about two trillion yen until now, which was only a part of total damage compensation cost. TEPCO had been provided more than 3.4 trillion yen by Nuclear Damage Liability Facilitation Cooperation, which would be put back by nuclear operators including TEPCO. TEPCO could obtain present raising funds and try to reconstruct business with restart of nuclear power, which might disturb energy reform. Present nuclear damage compensation scheme had better be reformed with learning more from Minamata disease case in Japan. (T. Tanaka)

  10. Ecological compensation and Environmental Impact Assessment in Spain

    Villarroya, Ana; Puig, Jordi

    2010-01-01

    To achieve meaningful sustainable development, Environmental Impact Assessment (EIA) should avoid the net losses in the environment resource base. But EIA practice does not always avoid the losses caused by the implementation of the projects under EIA regulation. Some environmental impacts are, simply, admitted, even without enforcing any form of compensation. When applied, compensation is sometimes just a monetary payment to offset the environmental loss. This paper looks for evidence on the role that compensation is given at present in EIA practice in Spain, and for some of its conceptual and regulatory roots. Specifically, it explores how compensation is addressed in 1302 records of decision (RODs) on those projects subject to the Spanish EIA regulation published during the years 2006 and 2007, to know how far Spain is from preserving the environmental resource base managed through this particular aspect of EIA practice. As a result, it is concluded that the practice of ecological compensation in EIA in Spain is much lower than it could be expected in a theoretical sustainability context committed to avoid net losses in the environment resource base, mainly due to an EIA practice focused on on-site mitigation that allows these net losses.

  11. Focusing horn

    1980-01-01

    This was the first magnetic horn developed by Simon Van der Meer to collect antiprotons in the AD complex. It was used for the AA (antiproton accumulator). Making an antiproton beam took a lot of time and effort. Firstly, protons were accelerated to an energy of 26 GeV/c (protons at 26GeV/c, antiprotons at 3.6GeV/c) in the PS and ejected onto a metal target. From the spray of emerging particles, a magnetic horn picked out 3.6 GeV antiprotons for injection into the AA through a wide-aperture focusing quadrupole magnet. For a million protons hitting the target, just one antiproton was captured, 'cooled' and accumulated. It took 3 days to make a beam of 3 x 10^11 -, three hundred thousand million - antiprotons. The development of this technology was a key step to the functioning of CERN's Super Proton Synchrotron as a proton - antiproton collider.

  12. Quantum electrodynamics with compensating current

    Bechler, A [Warsaw Univ. (Poland). Instytut Fizyki Teoretycznej

    1974-01-01

    A formulation of quantum electrodynamics is proposed in which all the propagators and field operators are gauge invariant. It is based on an old idea of Heisenberg and Euler which consists in the introduction of the linear integrals of potentials as arguments of the exponential functions. This method is generalized by an introduction of the so-called ''compensating currents'', which ensure local, i.e. in every point of space-time, charge conservation. The linear integral method is a particular case of that proposed in this paper. As the starting point we use quantum electrodynamics with a non-zero, small photon mass (Proca theory). It is shown that, due to the presence of the compensating current, the theory is fully renormalizable in Hilbert space with positive definite scalar product. The problem of the definition of the current operator is also briefly discussed.

  13. Executive compensation: a calibration approach

    Ivilina Popova; Joseph G. Haubrich

    1998-01-01

    We use a version of the Grossman and Hart principal-agent model with 10 actions and 10 states to produce quantitative predictions for executive compensation. Performance incentives derived from the model are compared with the performance incentives of 350 firms chosen from a survey by Michael Jensen and Kevin Murphy. The results suggest both that the model does a reasonable job of explaining the data and that actual incentives are close to the optimal incentives predicted by theory.

  14. Compensating Differentials for Sexual Harassment

    Joni Hersch

    2011-01-01

    Workplace sexual harassment is illegal, but many workers report that they have been sexually harassed. Exposure to the risk of sexual harassment may decrease productivity, which would reduce wages. Alternatively, workers may receive a compensating differential for exposure to sexual harassment, which would increase wages. Data on claims of sexual harassment filed with the Equal Employment Opportunity Commission are used to calculate the first measures of sexual harassment risks by industry, a...

  15. 23 CFR 751.15 - Just compensation.

    2010-04-01

    ... 23 Highways 1 2010-04-01 2010-04-01 false Just compensation. 751.15 Section 751.15 Highways... AND ACQUISITION § 751.15 Just compensation. (a) Just compensation shall be paid the owner for the... nonconforming junkyard as provided in § 751.11 must pertain at the time of the taking or removal in order to...

  16. Dynamic Phase Compensation of wind turbines

    Soerensen, P.; Skaarup, J.; Iov, Florin

    2004-01-01

    This paper describes a dynamic phase compensation unit for a wind turbine with directly connected induction generators. The compensation unit is based on thyristor switched capacitors, where conventional wind turbine compensations use mechanical contactors to switch the capacitors. The unit modules...

  17. 33 CFR 136.217 - Compensation allowable.

    2010-07-01

    ...) MARINE POLLUTION FINANCIAL RESPONSIBILITY AND COMPENSATION OIL SPILL LIABILITY TRUST FUND; CLAIMS PROCEDURES; DESIGNATION OF SOURCE; AND ADVERTISEMENT Procedures for Particular Claims § 136.217 Compensation... 33 Navigation and Navigable Waters 2 2010-07-01 2010-07-01 false Compensation allowable. 136.217...

  18. 33 CFR 136.205 - Compensation allowable.

    2010-07-01

    ...) MARINE POLLUTION FINANCIAL RESPONSIBILITY AND COMPENSATION OIL SPILL LIABILITY TRUST FUND; CLAIMS PROCEDURES; DESIGNATION OF SOURCE; AND ADVERTISEMENT Procedures for Particular Claims § 136.205 Compensation... 33 Navigation and Navigable Waters 2 2010-07-01 2010-07-01 false Compensation allowable. 136.205...

  19. 33 CFR 136.113 - Other compensation.

    2010-07-01

    ...) MARINE POLLUTION FINANCIAL RESPONSIBILITY AND COMPENSATION OIL SPILL LIABILITY TRUST FUND; CLAIMS PROCEDURES; DESIGNATION OF SOURCE; AND ADVERTISEMENT General Procedure § 136.113 Other compensation. A... 33 Navigation and Navigable Waters 2 2010-07-01 2010-07-01 false Other compensation. 136.113...

  20. The battle over workers' compensation.

    Ellenberger, J N

    2000-01-01

    Faced with lower profits and rapidly increasing premium costs in the 1980s, insurers and employer organizations cleverly parlayed the public perception of worker fraud and abuse in the workers' compensation system (that they helped to create) into massive legislative changes. Over the last decade, state legislators and governors, Republican and Democrat alike, have jumped on this bandwagon, one that workers and their allies have dubbed the workers' compensation "deform" movement. Alleging a "game plan" and a calculated campaign on the part of insurers and employers, the author looks at the major components of changes that were made, examines the elements of workers' compensation over which employers and insurers have gained control, and discusses Newt Gingrich's efforts to capitalize on employer and insurer fervor over the system. This campaign whistled through the country until it goaded the labor movement, injured workers, the trial bar, and others in Ohio in 1997 to organize themselves to stand up to employers by defeating the deform law through a ballot initiative. The article details that battle and suggests that similar voices can be achieved through a return to grassroots organizing and mobilization.

  1. Compensation Techniques in Accelerator Physics

    Sayed, Hisham Kamal [Old Dominion Univ., Norfolk, VA (United States)

    2011-05-01

    Accelerator physics is one of the most diverse multidisciplinary fields of physics, wherein the dynamics of particle beams is studied. It takes more than the understanding of basic electromagnetic interactions to be able to predict the beam dynamics, and to be able to develop new techniques to produce, maintain, and deliver high quality beams for different applications. In this work, some basic theory regarding particle beam dynamics in accelerators will be presented. This basic theory, along with applying state of the art techniques in beam dynamics will be used in this dissertation to study and solve accelerator physics problems. Two problems involving compensation are studied in the context of the MEIC (Medium Energy Electron Ion Collider) project at Jefferson Laboratory. Several chromaticity (the energy dependence of the particle tune) compensation methods are evaluated numerically and deployed in a figure eight ring designed for the electrons in the collider. Furthermore, transverse coupling optics have been developed to compensate the coupling introduced by the spin rotators in the MEIC electron ring design.

  2. Closing-in behavior: Compensation or attraction?

    Ambron, Elisabetta; Beschin, Nicoletta; Cerrone, Chiara; Della Sala, Sergio

    2018-03-01

    Closing-in behavior (CIB) defines the abnormal misplacement of the copy performance, positioned very closed to or on the top of the model. This symptom is observed in graphic copying by patients suffering from different neurological diseases, most commonly dementia. The cognitive origins of this behavior are still a matter of investigation, and research of the last 10 years has been focused on exploring 2 main accounts of CIB, the compensation and the attraction hypotheses, providing evidence in both directions. While the first account defines CIB as a compensatory strategy to overcome visuospatial and/or working memory deficits during copying tasks, the attraction hypothesis looks at CIB as primitive default behavior in which attention and action are closely coupled and movements are performed toward the focus of attention. We explored these 2 hypotheses in a sample of patients with and without CIB, and controls in 5 experiments: Experiments 1 and 2 tested the attraction hypothesis and, respectively, the prediction that CIB can be elicited in a noncopying dual task condition loading upon attentional resources or by irrelevant attentional grabbing stimuli. The other experiments investigated the compensation hypothesis manipulating the distance between model and copying space (Experiment 3), the task demand (single or dual task loading on verbal working memory; Experiment 4), the task requirements (copying and tracing) and visual demand (visual copy and memory; Experiment 5). The results support the attraction hypothesis of CIB. CIB reflects an impairment of the attention and action system, rather than a compensatory strategy. (PsycINFO Database Record (c) 2018 APA, all rights reserved).

  3. Plasticity during vestibular compensation: the role of saccades

    Hamish Gavin MacDougall

    2012-02-01

    Full Text Available This paper is focussed on one major aspect of compensation: the recent behavioural findings concerning oculomotor responses in human vestibular compensation and their possible implications for recovery after unilateral vestibular loss (UVL. New measurement techniques have provided new insights into how patients recover after UVL and have given clues for vestibular rehabilitation. Prior to this it has not been possible to quantify the level of function of all the peripheral vestibular sense organs. Now it is. By using vestibular-evoked myogenic potentials to measure utricular and saccular function and by new video head impulse testing to measure semicircular canal function to natural values of head accelerations. With these new video procedures it is now possible to measure both slow phase eye velocity and also saccades during natural head movements. The present evidence is that there is little or no recovery of slow phase eye velocity responses to natural head accelerations. It is doubtful as to whether the modest changes in slow phase eye velocity to small angular accelerations are functionally effective during compensation. On the other hand it is now clear that saccades can play a very important role in helping patients compensate and return to a normal lifestyle. Preliminary evidence suggests that different patterns of saccadic response may predict how well patients recover. It may be possible to train patients to produce more effective saccadic patterns in the first days after their unilateral loss. Some patients do learn new strategies, new behaviours, to conceal their inadequate VOR but when those strategies are prevented from operating by using passive, unpredictable, high acceleration natural head movements, as in the head impulse test, their vestibular loss can be demonstrated. It is those very strategies which the tests exclude, which may be the cause of their successful compensation.

  4. Assessment Can Support Reasoning and Sense Making

    Suurtam, Christine

    2012-01-01

    "Reasoning and sense making should occur in every classroom every day," states "Focus in High School Mathematics: Reasoning and Sense Making" (NCTM 2009, p. 5). As this book suggests, reasoning can take many forms, including explorations and conjectures as well as explanations and justifications of student thinking. Sense making, on the other…

  5. 38 CFR 21.3023 - Nonduplication; pension, compensation, and dependency and indemnity compensation.

    2010-07-01

    ... 38 Pensions, Bonuses, and Veterans' Relief 2 2010-07-01 2010-07-01 false Nonduplication; pension, compensation, and dependency and indemnity compensation. 21.3023 Section 21.3023 Pensions, Bonuses, and... Nonduplication; pension, compensation, and dependency and indemnity compensation. (a) Child; age 18. A child who...

  6. Automatic error compensation in dc amplifiers

    Longden, L.L.

    1976-01-01

    When operational amplifiers are exposed to high levels of neutron fluence or total ionizing dose, significant changes may be observed in input voltages and currents. These changes may produce large errors at the output of direct-coupled amplifier stages. Therefore, the need exists for automatic compensation techniques. However, previously introduced techniques compensate only for errors in the main amplifier and neglect the errors induced by the compensating circuitry. In this paper, the techniques introduced compensate not only for errors in the main operational amplifier, but also for errors induced by the compensation circuitry. Included in the paper is a theoretical analysis of each compensation technique, along with advantages and disadvantages of each. Important design criteria and information necessary for proper selection of semiconductor switches will also be included. Introduced in this paper will be compensation circuitry for both resistive and capacitive feedback networks

  7. DC-Compensated Current Transformer.

    Ripka, Pavel; Draxler, Karel; Styblíková, Renata

    2016-01-20

    Instrument current transformers (CTs) measure AC currents. The DC component in the measured current can saturate the transformer and cause gross error. We use fluxgate detection and digital feedback compensation of the DC flux to suppress the overall error to 0.15%. This concept can be used not only for high-end CTs with a nanocrystalline core, but it also works for low-cost CTs with FeSi cores. The method described here allows simultaneous measurements of the DC current component.

  8. Compensation culture reviewed: incentives to claim and damages levels

    Lewis, Richard Kurt

    2014-01-01

    This article reviews some recent developments which have affected the debate concerning ‘compensation culture.’ It focuses upon the number of claims and the cost of claims, looking especially at the level of damages. The role of insurers and the changing nature of personal injury practice are also discussed. The conclusion is that issues arising from the debate will continue for some time to come.

  9. Pervasive sensing

    Nagel, David J.

    2000-11-01

    The coordinated exploitation of modern communication, micro- sensor and computer technologies makes it possible to give global reach to our senses. Web-cameras for vision, web- microphones for hearing and web-'noses' for smelling, plus the abilities to sense many factors we cannot ordinarily perceive, are either available or will be soon. Applications include (1) determination of weather and environmental conditions on dense grids or over large areas, (2) monitoring of energy usage in buildings, (3) sensing the condition of hardware in electrical power distribution and information systems, (4) improving process control and other manufacturing, (5) development of intelligent terrestrial, marine, aeronautical and space transportation systems, (6) managing the continuum of routine security monitoring, diverse crises and military actions, and (7) medicine, notably the monitoring of the physiology and living conditions of individuals. Some of the emerging capabilities, such as the ability to measure remotely the conditions inside of people in real time, raise interesting social concerns centered on privacy issues. Methods for sensor data fusion and designs for human-computer interfaces are both crucial for the full realization of the potential of pervasive sensing. Computer-generated virtual reality, augmented with real-time sensor data, should be an effective means for presenting information from distributed sensors.

  10. [Pre-verbality in focusing and the need for self check. An attempt at "focusing check"].

    Masui, T; Ikemi, A; Murayama, S

    1983-06-01

    Though the Focusing process is not entirely non-verbal, in Focusing, careful attention is paid by the Focuser and the Listener to the pre-verbal experiential process. In other words, Focusing involves attending to the felt sense that is not easily expressed in words immediately. Hence, during the process of learning to Focus, the Focusing teacher attempts to communicate the experiences of Focusing to the student which are not easily done by words. Due to such difficulties, the Focusing student may (and quite frequently does) mistake the experiential process in Focusing with other processes. Often, the felt sense can be confused with other phenomena such as "autogenic discharge". Also the Focuser may not stay with the felt sense and drift into "free association" or frequently, certain processes in "meditation" can be confused with Focusing. Therefore, there is a need for a "check" by which the Focusing student can confirm the Focusing experience for himself. For the Focusing student, such a "check" serves not only to confirm the Focusing process, but also an aid to learning Focusing. We will report here a "Focusing Check" which we developed by translating Eugene Gendlin's "Focusing Check" and making several modifications in it so that it will be more understandable to the Japanese. Along with the "Focusing Check" we developed, the authors discuss the need for such a check.

  11. Overview of the compensation and liability regimes under the International Oil Pollution Compensation Fund (IOPC)

    Wren, John [Department of Environment, Transport and the Regions, Shipping Policy Div., London (United Kingdom)

    2000-08-01

    This paper focuses on the cost recovery issues arising through the operation of the International Oil Pollution Compensation Fund (IOPC) and administrative matters which arose following the Braer and Sea Empress oil tanker pollution incidents in the UK. Each of these oil spills brought very different problems. Any major oil spill will have prolonged economic and social consequences for the communities affected. Membership of the International Oil Pollution Compensation Fund (IOPC Fund) will do much to soften the impact as regards economic damage. However, the operation of the Fund brings difficulties which may not have been considered by the administration prior to the spill. Some of the difficulties are foreseeable. It covers details of the international compensation and liability regimes, it considers a number of administrative consequences and highlights seven lessons that have been learned in the UK in the light of recent experience. These lessons are: Claims may not be paid quickly or in full. Claimants will need advice and government involvement. Action by the government may be needed to complement the IOPC Fund. Governments have to balance their obligations as a member state with the needs of claimants. It is better for claimants to keep matters out of court for as long as possible. Administrative consequences will continue for a long time after the oil has been cleared from the shore-line. Each major oil spill brings different cost recovery problems and will also bring demands 'to learn the lessons'. In much the same way as contingency plans are regularly tested, each state party to the regime would be wise, from time to time, to think through the likely scenarios so as to better prepare themselves in the light of experiences elsewhere. The United Kingdom has had rather more experience in recent years than it would have wished. (Author)

  12. Overview of the compensation and liability regimes under the International Oil Pollution Compensation Fund (IOPC)

    Wren, John

    2000-01-01

    This paper focuses on the cost recovery issues arising through the operation of the International Oil Pollution Compensation Fund (IOPC) and administrative matters which arose following the Braer and Sea Empress oil tanker pollution incidents in the UK. Each of these oil spills brought very different problems. Any major oil spill will have prolonged economic and social consequences for the communities affected. Membership of the International Oil Pollution Compensation Fund (IOPC Fund) will do much to soften the impact as regards economic damage. However, the operation of the Fund brings difficulties which may not have been considered by the administration prior to the spill. Some of the difficulties are foreseeable. It covers details of the international compensation and liability regimes, it considers a number of administrative consequences and highlights seven lessons that have been learned in the UK in the light of recent experience. These lessons are: Claims may not be paid quickly or in full. Claimants will need advice and government involvement. Action by the government may be needed to complement the IOPC Fund. Governments have to balance their obligations as a member state with the needs of claimants. It is better for claimants to keep matters out of court for as long as possible. Administrative consequences will continue for a long time after the oil has been cleared from the shore-line. Each major oil spill brings different cost recovery problems and will also bring demands 'to learn the lessons'. In much the same way as contingency plans are regularly tested, each state party to the regime would be wise, from time to time, to think through the likely scenarios so as to better prepare themselves in the light of experiences elsewhere. The United Kingdom has had rather more experience in recent years than it would have wished. (Author)

  13. Robust finite-time tracking control for nonlinear suspension systems via disturbance compensation

    Pan, Huihui; Jing, Xingjian; Sun, Weichao

    2017-05-01

    This paper focuses on the finite-time tracking control with external disturbance for active suspension systems. In order to compensate unknown disturbance efficiently, a disturbance compensator with finite-time convergence property is studied. By analyzing the discontinuous phenomenon of classical disturbance compensation techniques, this study presents a simple approach to construct a continuous compensator satisfying the finite-time disturbance rejection performance. According to the finite-time separation principle, the design procedures of the nominal controller for the suspension system without disturbance and the disturbance compensator can be implemented in a completely independent manner. Therefore, the overall control law for the closed-loop system is continuous, which offers some distinct advantages over the existing discontinuous ones. From the perspective of practical implementation, the continuous controller can avoid effectively the unexpected chattering in active suspension control. Comparative experimental results are presented and discussed to illustrate the advantage and effectiveness of the proposed control strategy.

  14. Hall mobility reduction in single-crystalline silicon gradually compensated by thermal donors activation

    Veirman, J.; Dubois, S.; Enjalbert, N.; Garandet, J. P.; Heslinga, D. R.; Lemiti, M.

    2010-06-01

    This letter focuses on the variation of the Hall majority carrier mobility with the dopant compensation level in purely Boron-doped Czochralski grown silicon single crystals. Compensation was varied continuously at the sample scale via a step by step activation of the oxygen-based thermal donors. At room temperature, we show a strong drop in mobility for high compensation levels in both p- and n-type Si. Mobility models taking into account carrier scattering on ionized impurities and phonons could not reproduce this drop. We conclude that a specific effect of compensation must be taken into account to explain the observed behaviour. We qualitatively discuss physical mechanisms susceptible to reduce mobility in highly compensated Si.

  15. Vertical vibration analysis for elevator compensating sheave

    Watanabe, Seiji; Nakazawa, Daisuke; Fukui, Daiki; Okawa, Takeya

    2013-01-01

    Most elevators applied to tall buildings include compensating ropes to satisfy the balanced rope tension between the car and the counter weight. The compensating ropes receive tension by the compensating sheave, which is installed at the bottom space of the elevator shaft. The compensating sheave is only suspended by the compensating ropes, therefore, the sheave can move vertically while the car is traveling. This paper shows the elevator dynamic model to evaluate the vertical motion of the compensating sheave. Especially, behavior in emergency cases, such as brake activation and buffer strike, was investigated to evaluate the maximum upward motion of the sheave. The simulation results were validated by experiments and the most influenced factor for the sheave vertical motion was clarified

  16. How to avoid deferred-compensation troubles.

    Freeman, Todd I

    2005-06-01

    Executive compensation packages have long included stock options and deferred compensation plans in order to compete for talent. Last year, Congress passed a law in response to the Enron debacle, in which executives were perceived to be protecting their deferred compensation at the expense of employees, creditors, and investors. The new law is designed to protect companies and their shareholders from being raided by the very executives that guided the company to financial ruin. Physicians who are part owners of medical practices need to know about the changes in the law regarding deferred compensation and how to avoid costly tax penalties. This article discusses how the changes affect medical practices as well as steps physician-owned clinics can take to avoid the risk of penalty, such as freezing deferred compensation and creating a new deferred compensation plan.

  17. Vertical vibration analysis for elevator compensating sheave

    Watanabe, Seiji; Okawa, Takeya; Nakazawa, Daisuke; Fukui, Daiki

    2013-07-01

    Most elevators applied to tall buildings include compensating ropes to satisfy the balanced rope tension between the car and the counter weight. The compensating ropes receive tension by the compensating sheave, which is installed at the bottom space of the elevator shaft. The compensating sheave is only suspended by the compensating ropes, therefore, the sheave can move vertically while the car is traveling. This paper shows the elevator dynamic model to evaluate the vertical motion of the compensating sheave. Especially, behavior in emergency cases, such as brake activation and buffer strike, was investigated to evaluate the maximum upward motion of the sheave. The simulation results were validated by experiments and the most influenced factor for the sheave vertical motion was clarified.

  18. User-centric incentive design for participatory mobile phone sensing

    Gao, Wei; Lu, Haoyang

    2014-05-01

    Mobile phone sensing is a critical underpinning of pervasive mobile computing, and is one of the key factors for improving people's quality of life in modern society via collective utilization of the on-board sensing capabilities of people's smartphones. The increasing demands for sensing services and ambient awareness in mobile environments highlight the necessity of active participation of individual mobile users in sensing tasks. User incentives for such participation have been continuously offered from an application-centric perspective, i.e., as payments from the sensing server, to compensate users' sensing costs. These payments, however, are manipulated to maximize the benefits of the sensing server, ignoring the runtime flexibility and benefits of participating users. This paper presents a novel framework of user-centric incentive design, and develops a universal sensing platform which translates heterogenous sensing tasks to a generic sensing plan specifying the task-independent requirements of sensing performance. We use this sensing plan as input to reduce three categories of sensing costs, which together cover the possible sources hindering users' participation in sensing.

  19. Nanometric locking of the tight focus for optical microscopy and tip-enhanced microscopy

    Hayazawa, N; Furusawa, K; Kawata, S

    2012-01-01

    We have successfully stabilized the tight focus onto the sample surface of an optical microscope within ±1.0 nm for a virtually unlimited time duration. The time-dependent thermal drift of the tight focus and the mechanical tilt of the sample surface were simultaneously sensed by a non-optical means based on a capacitive sensor and were compensated for in real-time. This non-optical scheme is promising for the suppression of background light sources for optical microscopy. The focus stabilization is crucial for microscopic measurement at an interface, particularly when scanning a large surface area, because there is always a certain amount of mechanical tilt of the sample substrate, which degrades the contrast of the image. When imaging nanoscopic materials such as carbon nanotubes or silicon nanowires, more stringent nanometric stabilization of the focus position relative to such samples is required, otherwise it is often difficult to interpret the results from the observations. Moreover, the smaller the sample volume is, the smaller the signal becomes, resulting in a long exposure time at each position. In this sense, long-term stability of the tight focus is essential for both microscopic large area scanning and nanosized sample scanning (high-resolution/large-area imaging). In addition, the recently developed tip-enhanced microscopy requires long-term stability of the relative position of the tip, sample and focus position. We were able to successfully demonstrate a stability improvement for tip-enhanced microscopy in the same manner. The stabilization of the tight focus enables us to perform long-term and robust measurements without any degradation of optical signal, resulting in the capability of true nanometric optical imaging with good reproducibility and high precision. The technique presented is a simple add-on for any kind of optical microscope. (paper)

  20. Enthalpy-entropy compensation in protein unfolding

    2000-01-01

    Enthalpy-entropy compensation was found to be a universal law in protein unfolding based on over 3 000 experimental data. Water molecular reorganization accompanying the protein unfolding was suggested as the origin of the enthalpy-entropy compensation in protein unfolding. It is indicated that the enthalpy-entropy compensation constitutes the physical foundation that satisfies the biological need of the small free energy changes in protein unfolding, without the sacrifice of the bio-diversity of proteins. The enthalpy-entropy compensation theory proposed herein also provides valuable insights into the Privalov's puzzle of enthalpy and entropy convergence in protein unfolding.

  1. Multi-qubit compensation sequences

    Tomita, Y; Merrill, J T; Brown, K R

    2010-01-01

    The Hamiltonian control of n qubits requires precision control of both the strength and timing of interactions. Compensation pulses relax the precision requirements by reducing unknown but systematic errors. Using composite pulse techniques designed for single qubits, we show that systematic errors for n-qubit systems can be corrected to arbitrary accuracy given either two non-commuting control Hamiltonians with identical systematic errors or one error-free control Hamiltonian. We also examine composite pulses in the context of quantum computers controlled by two-qubit interactions. For quantum computers based on the XY interaction, single-qubit composite pulse sequences naturally correct systematic errors. For quantum computers based on the Heisenberg or exchange interaction, the composite pulse sequences reduce the logical single-qubit gate errors but increase the errors for logical two-qubit gates.

  2. Self compensating fire detection device

    Cholin, J. M.

    1985-01-01

    A device employing ionization principles for fire detection disclosing a configuration which allows compensation for adverse effects due to the flow of the gas through the device or due to the accumulation of dust and dirt therein. The detecting device includes two ionization chambers, each having a first member, such as a cylindrically shaped cup, having first and second conductive surface portions. Each chamber also incudes a second member, such as a circular, electrode disc having two conductive surface portions. There is disposed in each chamber a radioactive source for ionizing the gas in the volumes intervening between respective pairs of surfaces. The area dimensions of the respective pairs of surfaces, the interventing volumes and the distances there between, and the relative orientation of the respective pairs are calculated and placed such that the ionization currents flowing between pairs of conductive surfaces are substantially equal and orthogonal to each other

  3. Conversational sensing

    Preece, Alun; Gwilliams, Chris; Parizas, Christos; Pizzocaro, Diego; Bakdash, Jonathan Z.; Braines, Dave

    2014-05-01

    Recent developments in sensing technologies, mobile devices and context-aware user interfaces have made it pos- sible to represent information fusion and situational awareness for Intelligence, Surveillance and Reconnaissance (ISR) activities as a conversational process among actors at or near the tactical edges of a network. Motivated by use cases in the domain of Company Intelligence Support Team (CoIST) tasks, this paper presents an approach to information collection, fusion and sense-making based on the use of natural language (NL) and controlled nat- ural language (CNL) to support richer forms of human-machine interaction. The approach uses a conversational protocol to facilitate a ow of collaborative messages from NL to CNL and back again in support of interactions such as: turning eyewitness reports from human observers into actionable information (from both soldier and civilian sources); fusing information from humans and physical sensors (with associated quality metadata); and assisting human analysts to make the best use of available sensing assets in an area of interest (governed by man- agement and security policies). CNL is used as a common formal knowledge representation for both machine and human agents to support reasoning, semantic information fusion and generation of rationale for inferences, in ways that remain transparent to human users. Examples are provided of various alternative styles for user feedback, including NL, CNL and graphical feedback. A pilot experiment with human subjects shows that a prototype conversational agent is able to gather usable CNL information from untrained human subjects.

  4. Remote sensing: best practice

    Brown, Gareth [Sgurr Energy (Canada)

    2011-07-01

    This paper presents remote sensing best practice in the wind industry. Remote sensing is a technique whereby measurements are obtained from the interaction of laser or acoustic pulses with the atmosphere. There is a vast diversity of tools and techniques available and they offer wide scope for reducing project uncertainty and risk but best practice must take into account versatility and flexibility. It should focus on the outcome in terms of results and data. However, traceability of accuracy requires comparison with conventional instruments. The framework for the Boulder protocol is given. Overviews of the guidelines for IEA SODAR and IEA LIDAR are also mentioned. The important elements of IEC 61400-12-1, an international standard for wind turbines, are given. Bankability is defined based on the Boulder protocol and a pie chart is presented that illustrates the uncertainty area covered by remote sensing. In conclusion it can be said that remote sensing is changing perceptions about how wind energy assessments can be made.

  5. Carbon for sensing devices

    Tagliaferro, Alberto

    2015-01-01

    This book reveals why carbon is playing such an increasingly prominent role as a sensing material. The various steps that transform a raw material in a sensing device are thoroughly presented and critically discussed.  The authors deal with all aspects of carbon-based sensors, starting from the various hybridization and allotropes of carbon, with specific focus on micro and nanosized carbons (e.g., carbon nanotubes, graphene) and their growth processes. The discussion then moves to the role of functionalization and the different routes to achieve it. Finally, a number of sensing applications in various fields are presented, highlighting the connection with the basic properties of the various carbon allotropes.  Readers will benefit from this book’s bottom-up approach, which starts from the local bonding in carbon solids and ends with sensing applications, linking the local hybridization of carbon atoms and its modification by functionalization to specific device performance. This book is a must-have in th...

  6. SAR Imaging of Ground Moving Targets with Non-ideal Motion Error Compensation(in English

    Zhou Hui

    2015-06-01

    Full Text Available Conventional ground moving target imaging algorithms mainly focus on the range cell migration correction and the motion parameter estimation of the moving target. However, in real Synthetic Aperture Radar (SAR data processing, non-ideal motion error compensation is also a critical process, which focuses and has serious impacts on the imaging quality of moving targets. Non-ideal motion error can not be compensated by either the stationary SAR motion error compensation algorithms or the autofocus techniques. In this paper, two sorts of non-ideal motion errors that affect the Doppler centroid of the moving target is analyzed, and a novel non-ideal motion error compensation algorithm is proposed based on the Inertial Navigation System (INS data and the range walk trajectory. Simulated and real data processing results are provided to demonstrate the effectiveness of the proposed algorithm.

  7. TopSPICE Simulations for Temperature Compensation of ISFET/MEMFET Micro-Sensor

    Sawsen AZZOUZI

    2014-05-01

    Full Text Available In this work, an ISFET (Ion Sensitive Field Effect Transistor/MEMFET (Membrane Field Effect Transistor interface circuit with temperature compensation has been successfully designed and simulated. In each interface, we used the macro-model of ISFET/MEMFET based chemical sensors simulated in TopSPICE. The simulation results of the different sensing circuits of ISFET/MEMFETs for temperature compensation show that the readout configuration for ISFET/MEMFET sensors based on Wheatstone-Bridge connection is the most effective with a temperature drift 5´10-6 mV/°C.

  8. Complexities in understanding the role of compensation-related factors on recovery from whiplash-associated disorders : discussion paper 2

    Carroll, Linda J.; Connelly, Luke B.; Spearing, Natalie M.; Cote, Pierre; Buitenhuis, Jan; Kenardy, Justin

    2011-01-01

    Study Design. Focused discussion. Objective. To present some of the complexities in conducting research on the role of compensation and compensation-related factors in recovery from whiplash-associated disorders (WAD) and to suggest directions for future research. Summary of Background Data. There

  9. Remote RemoteRemoteRemote sensing potential for sensing ...

    Remote RemoteRemoteRemote sensing potential for sensing potential for sensing potential for sensing potential for sensing potential for sensing potential for sensing potential for sensing potential for sensing potential for sensing potential for sensing p. A Ngie, F Ahmed, K Abutaleb ...

  10. 38 CFR 3.351 - Special monthly dependency and indemnity compensation, death compensation, pension and spouse's...

    2010-07-01

    ... 38 Pensions, Bonuses, and Veterans' Relief 1 2010-07-01 2010-07-01 false Special monthly dependency and indemnity compensation, death compensation, pension and spouse's compensation ratings. 3.351 Section 3.351 Pensions, Bonuses, and Veterans' Relief DEPARTMENT OF VETERANS AFFAIRS ADJUDICATION Pension...

  11. Focus in High School Mathematics: Statistics and Probability

    National Council of Teachers of Mathematics, 2009

    2009-01-01

    Reasoning about and making sense of statistics and probability are essential to students' future success. This volume belongs to a series that supports National Council of Teachers of Mathematics' (NCTM's) "Focus in High School Mathematics: Reasoning and Sense Making" by providing additional guidance for making reasoning and sense making part of…

  12. 77 FR 58469 - Plum Pox Compensation

    2012-09-21

    .... APHIS-2011-0004] RIN 0579-AD58 Plum Pox Compensation AGENCY: Animal and Plant Health Inspection Service... interim rule that amended the plum pox regulations to provide for the payment of compensation to eligible... are required to be destroyed in order to prevent the spread of plum pox. The interim rule also...

  13. 33 CFR 136.211 - Compensation allowable.

    2010-07-01

    ...) MARINE POLLUTION FINANCIAL RESPONSIBILITY AND COMPENSATION OIL SPILL LIABILITY TRUST FUND; CLAIMS PROCEDURES; DESIGNATION OF SOURCE; AND ADVERTISEMENT Procedures for Particular Claims § 136.211 Compensation... that amount required to accomplish the activities for which the claim was paid. Real or Personal...

  14. Multiple Compensation Consultants and CEO Pay

    Kabir, Mohammed Rezaul; Minhat, Marizah

    The study examines the practice of employing multiple compensation consultants. Data for a sample of UK companies over the period 2003-2006 are analyzed using a variety of econometric methods. We find that CEOs receive higher equity-based pay when firms employ more than one compensation consultant.

  15. Compensation of oscillation coupling induced by solenoids

    Zelinskij, A.Yu.; Karnaukhov, I.M.; Shcherbakov, A.A.

    1988-01-01

    Methods for construction of various schemes of oscillation coupling compensation, induced by solenoids in charged particle storage rings, are described. Peculiarities of magnetic structure, enabling to localize oscillation coupling in wide energy range are discussed. Results of calculation of compensation schemes for design of NR-2000 storage ring spin rotation are presented

  16. Individual Hearing Loss: Characterization, Modelling, Compensation Strategies

    Santurette, Sébastien; Dau, Torsten; Christensen-Dalsgaard, Jakob

    2016-01-01

    account for such individual differences, which make it challenging to find adequate compensation strategies in hearing devices. How to characterize, model, and compensate for individual hearing loss were the main topics of the fifth International Symposium on Auditory and Audiological Research (ISAAR...

  17. 75 FR 76079 - Sound Incentive Compensation Guidance

    2010-12-07

    ... management; and Be supported by strong corporate governance, including active and effective oversight by the... Sound Compensation Practices adopted by the Financial Stability Board (FSB) in April 2009, as well as... will promote the prompt improvement of incentive compensation practices in the banking industry by...

  18. 75 FR 53023 - Sound Incentive Compensation Guidance

    2010-08-30

    ... management; and Be supported by strong corporate governance, including active and effective oversight by the... Sound Compensation Practices adopted by the Financial Stability Board (FSB) in April 2009, as well as... will promote the prompt improvement of incentive compensation practices in the banking industry by...

  19. 75 FR 22679 - Sound Incentive Compensation Guidance

    2010-04-29

    ... management; and Be supported by strong corporate governance, including active and effective oversight by the... Sound Compensation Practices adopted by the Financial Stability Board (FSB) in April 2009, as well as... will promote the prompt improvement of incentive compensation practices in the banking industry by...

  20. High rate of awarding compensation for claims of injuries related to clinical trials by pharmaceutical companies in Japan: a questionnaire survey.

    Kurihara, Chieko; Kusuoka, Hideo; Ono, Shunsuke; Kakee, Naoko; Saito, Kazuyuki; Takehara, Kenji; Tsujide, Kiyokazu; Nabeoka, Yuzo; Sakuhiro, Takuya; Aoki, Hiroshi; Morishita, Noriko; Suzuki, Chieko; Kachi, Shigeo; Kondo, Emiko; Komori, Yukiko; Isobe, Tetsu; Kageyama, Shigeru; Watanabe, Hiroshi

    2014-01-01

    International norms and ethical standards have suggested that compensation for research-related injury should be provided to injured research volunteers. However, statistical data of incidence of compensation claims and the rate of awarding them have been rarely reported. Questionnaire surveys were sent to pharmaceutical companies and medical institutions, focusing on industry-initiated clinical trials aiming at new drug applications (NDAs) on patient volunteers in Japan. With the answers from pharmaceutical companies, the incidence of compensation was 0.8%, including 0.06% of monetary compensation. Of the cases of compensation claims, 99% were awarded. In turn, with the answers from medical institutions, the incidence of compensation was 0.6%, including 0.4% of serious but not death cases, and 0.04% of death cases. Furthermore, most claims for compensation were initiated by medical institutions, rather than by the patients. On the other hand, with the answers from clinical trial volunteers, 3% of respondents received compensations. These compensated cases were 25% of the injuries which cannot be ruled out from the scope of compensation. Our study results demonstrated that Japanese pharmaceutical companies have provided a high rate of compensation for clinical trial-related injuries despite the possibility of overestimation. In the era of global clinical development, our study indicates the importance of further surveys to find each country's compensation policy by determining how it is being implemented based on a survey of the actual status of compensation coming from statistical data.

  1. Structural Pain Compensating Flight Control

    Miller, Chris J.

    2014-01-01

    The problem of control command and maneuver induced structural loads is an important aspect of any control system design. Designers must design the aircraft structure and the control architecture to achieve desired piloted control responses while limiting the imparted structural loads. The classical approach is to build the structure with high margins, restrict control surface commands to known good combinations, and train pilots to follow procedural maneuvering limitations. With recent advances in structural sensing and the continued desire to improve safety and vehicle fuel efficiency, it is both possible and desirable to develop control architectures that enable lighter vehicle weights while maintaining and improving protection against structural damage.

  2. Sensing with Ion Channels

    Martinac, Boris

    2008-01-01

    All living cells are able to detect and translate environmental stimuli into biologically meaningful signals. Sensations of touch, hearing, sight, taste, smell or pain are essential to the survival of all living organisms. The importance of sensory input for the existence of life thus justifies the effort made to understand its molecular origins. Sensing with Ion Channels focuses on ion channels as key molecules enabling biological systems to sense and process the physical and chemical stimuli that act upon cells in their living environment. Its aim is to serve as a reference to ion channel specialists and as a source of new information to non specialists who want to learn about the structural and functional diversity of ion channels and their role in sensory physiology.

  3. HORIZON SENSING

    Larry G. Stolarczyk

    2003-03-18

    With the aid of a DOE grant (No. DE-FC26-01NT41050), Stolar Research Corporation (Stolar) developed the Horizon Sensor (HS) to distinguish between the different layers of a coal seam. Mounted on mining machine cutter drums, HS units can detect or sense the horizon between the coal seam and the roof and floor rock, providing the opportunity to accurately mine the section of the seam most desired. HS also enables accurate cutting of minimum height if that is the operator's objective. Often when cutting is done out-of-seam, the head-positioning function facilitates a fixed mining height to minimize dilution. With this technology, miners can still be at a remote location, yet cut only the clean coal, resulting in a much more efficient overall process. The objectives of this project were to demonstrate the feasibility of horizon sensing on mining machines and demonstrate that Horizon Sensing can allow coal to be cut cleaner and more efficiently. Stolar's primary goal was to develop the Horizon Sensor (HS) into an enabling technology for full or partial automation or ''agile mining''. This technical innovation (R&D 100 Award Winner) is quickly demonstrating improvements in productivity and miner safety at several prominent coal mines in the United States. In addition, the HS system can enable the cutting of cleaner coal. Stolar has driven the HS program on the philosophy that cutting cleaner coal means burning cleaner coal. The sensor, located inches from the cutting bits, is based upon the physics principles of a Resonant Microstrip Patch Antenna (RMPA). When it is in proximity of the rock-coal interface, the RMPA impedance varies depending on the thickness of uncut coal. The impedance is measured by the computer-controlled electronics and then sent by radio waves to the mining machine. The worker at the machine can read the data via a Graphical User Interface, displaying a color-coded image of the coal being cut, and direct the machine

  4. Compensation of Disadvantages in University Examination Procedures

    Ulrike Quapp

    2016-08-01

    Full Text Available Active social participation of disabled people is one of the major tasks of modern society. That also includes access to the academic community by higher education. Universities all over the world work hard to give handicapped students a chance to graduate. In this context, compensation of disadvantages in examination procedures is an important matter. But, also chronic illness may impair the student's examination performance. To ensure equal examination opportunities for all students, responsible university officials must be creative to find individual compensation solutions. The paper analyzes examination regulations at universities in different countries and offers solutions to compensate disabled and chronic ill students' disadvantages. It discusses the necessity of compensation for different types of disability and chronic illness. Finally, an overview of current German case law and solutions for compensation problems are provided.

  5. Analyses of compensation related defects in II-VI compounds

    Castaldini, A.; Cavallini, A.; Fraboni, B.; Fernandez, P.; Piqueras, J.

    1998-01-01

    The deep levels present in semiconducting CdTe and semi-insulating (SI) CdTe:Cl and Cd 0.8 Zn 0.2 Te have been investigated by means of cathodoluminescence (CL), deep level transient spectroscopy (DLTS), photo-DLTS (PDLTS) and photo induced current transient spectroscopy (PICTS). PICTS and PDLTS can be applied to SI materials and allowed to determine whether the observed deep levels are hole or electron traps. Among the observed deep centers, the authors have focused their attention on those involved in the compensation process such as the so called center A and the deep traps located near midgap. They have identified a deep acceptor, labelled H, and a deep donor, labelled E, the latter is peculiar to CdTe:Cl and can be a good candidate for the deep donor level needed to explain the compensation process in SI CdTe:Cl

  6. Molecular Mechanisms Regulating Temperature Compensation of the Circadian Clock.

    Narasimamurthy, Rajesh; Virshup, David M

    2017-01-01

    An approximately 24-h biological timekeeping mechanism called the circadian clock is present in virtually all light-sensitive organisms from cyanobacteria to humans. The clock system regulates our sleep-wake cycle, feeding-fasting, hormonal secretion, body temperature, and many other physiological functions. Signals from the master circadian oscillator entrain peripheral clocks using a variety of neural and hormonal signals. Even centrally controlled internal temperature fluctuations can entrain the peripheral circadian clocks. But, unlike other chemical reactions, the output of the clock system remains nearly constant with fluctuations in ambient temperature, a phenomenon known as temperature compensation. In this brief review, we focus on recent advances in our understanding of the posttranslational modifications, especially a phosphoswitch mechanism controlling the stability of PER2 and its implications for the regulation of temperature compensation.

  7. Molecular Mechanisms Regulating Temperature Compensation of the Circadian Clock

    David M. Virshup

    2017-04-01

    Full Text Available An approximately 24-h biological timekeeping mechanism called the circadian clock is present in virtually all light-sensitive organisms from cyanobacteria to humans. The clock system regulates our sleep–wake cycle, feeding–fasting, hormonal secretion, body temperature, and many other physiological functions. Signals from the master circadian oscillator entrain peripheral clocks using a variety of neural and hormonal signals. Even centrally controlled internal temperature fluctuations can entrain the peripheral circadian clocks. But, unlike other chemical reactions, the output of the clock system remains nearly constant with fluctuations in ambient temperature, a phenomenon known as temperature compensation. In this brief review, we focus on recent advances in our understanding of the posttranslational modifications, especially a phosphoswitch mechanism controlling the stability of PER2 and its implications for the regulation of temperature compensation.

  8. 我國法上專利侵權賠償責任之主觀要件──以智財法院判決實證研究為中心 Subjective Criteria of Patent Infringement Compensation in Taiwan: Focusing on Empirical Investigation of Intellectual Property Court’s Decisions

    洪紹庭 Shao-Ting Hong

    2015-06-01

    Full Text Available 我國過去專利侵權賠償責任之主觀要件,由於舊專利法中並未明文規定,學者與實務多認應回歸民法侵權行為之主觀要件,然而,該主觀要件之故意過失,究竟採取何種標準,當時尚存有爭議。經過學術與實務見解逐漸統一後,如今2013 年新專利法已經明定採取過失責任,亦即專利侵權損害賠償之成立,除系爭專利有效、系爭產品落入專利權範圍外,被控侵權人仍需要有主觀上故意過失,始負專利侵權之賠償責任。侵權行為之過失責任概念,係採善良管理人注意義務,基於專利制度的特殊性,此一注意義務之概念在專利法中應該如何適用,不同專利侵權案件的潛在侵權人應負注意義務 的範圍為何,以及侵權故意如何認定,係本文欲探討之對象。本文實證研究針對智慧財產法院成立以來之專利民事判決,探討我國審判實務上專利侵權賠償主觀要件的判斷標準。研究結果發現,智財法院將過失概念予以客觀化及類型化,對於不同類型之被控侵權人採用高、中、低等三種不同強度之注意義務判斷標準,殊值注意。 Previously, subjective elements of patent infringement compensation were not stipulated in Taiwanese patent law. Most scholars and courts referred to tort law for guidance. They initially disagreed on the issue whether the compensation for patent infringement should be strict liability, negligent liability, or the latter with assumption of negligence, but over time their view converges and largely considered it as a type of negligent liability, which is explicitly adopted by the patent law in 2013. In other words, even though the patent at bar in a litigation is valid and infringed, the patent owner still has to prove the defendant’s intent or negligence as to the infringement to recover monetary damages. This paper investigates decisions of the

  9. 42 CFR 413.102 - Compensation of owners.

    2010-10-01

    ...) Definitions—(1) Compensation. Compensation means the total benefit received by the owner for the services he... 42 Public Health 2 2010-10-01 2010-10-01 false Compensation of owners. 413.102 Section 413.102... § 413.102 Compensation of owners. (a) Principle. A reasonable allowance of compensation for services of...

  10. Self Organization in Compensated Semiconductors

    Berezin, Alexander A.

    2004-03-01

    In partially compensated semiconductor (PCS) Fermi level is pinned to donor sub-band. Due to positional randomness and almost isoenergetic hoppings, donor-spanned electronic subsystem in PCS forms fluid-like highly mobile collective state. This makes PCS playground for pattern formation, self-organization, complexity emergence, electronic neural networks, and perhaps even for origins of life, bioevolution and consciousness. Through effects of impact and/or Auger ionization of donor sites, whole PCS may collapse (spinodal decomposition) into microblocks potentially capable of replication and protobiological activity (DNA analogue). Electronic screening effects may act in RNA fashion by introducing additional length scale(s) to system. Spontaneous quantum computing on charged/neutral sites becomes potential generator of informationally loaded microstructures akin to "Carl Sagan Effect" (hidden messages in Pi in his "Contact") or informational self-organization of "Library of Babel" of J.L. Borges. Even general relativity effects at Planck scale (R.Penrose) may affect the dynamics through (e.g.) isotopic variations of atomic mass and local density (A.A.Berezin, 1992). Thus, PCS can serve as toy model (experimental and computational) at interface of physics and life sciences.

  11. Forest structural assessment using remote sensing technologies: an ...

    -Natal and MONDI Business Paper have recently embarked on a remote sensing cooperative. The primary focus of this cooperative is to explore the potential benefits associated with using remote sensing for forestry-related activities.

  12. New inverse synthetic aperture radar algorithm for translational motion compensation

    Bocker, Richard P.; Henderson, Thomas B.; Jones, Scott A.; Frieden, B. R.

    1991-10-01

    Inverse synthetic aperture radar (ISAR) is an imaging technique that shows real promise in classifying airborne targets in real time under all weather conditions. Over the past few years a large body of ISAR data has been collected and considerable effort has been expended to develop algorithms to form high-resolution images from this data. One important goal of workers in this field is to develop software that will do the best job of imaging under the widest range of conditions. The success of classifying targets using ISAR is predicated upon forming highly focused radar images of these targets. Efforts to develop highly focused imaging computer software have been challenging, mainly because the imaging depends on and is affected by the motion of the target, which in general is not precisely known. Specifically, the target generally has both rotational motion about some axis and translational motion as a whole with respect to the radar. The slant-range translational motion kinematic quantities must be first accurately estimated from the data and compensated before the image can be focused. Following slant-range motion compensation, the image is further focused by determining and correcting for target rotation. The use of the burst derivative measure is proposed as a means to improve the computational efficiency of currently used ISAR algorithms. The use of this measure in motion compensation ISAR algorithms for estimating the slant-range translational motion kinematic quantities of an uncooperative target is described. Preliminary tests have been performed on simulated as well as actual ISAR data using both a Sun 4 workstation and a parallel processing transputer array. Results indicate that the burst derivative measure gives significant improvement in processing speed over the traditional entropy measure now employed.

  13. Complexities in understanding the role of compensation-related factors on recovery from whiplash-associated disorders: discussion paper 2.

    Carroll, Linda J; Connelly, Luke B; Spearing, Natalie M; Côté, Pierre; Buitenhuis, Jan; Kenardy, Justin

    2011-12-01

    Focused discussion. To present some of the complexities in conducting research on the role of compensation and compensation-related factors in recovery from whiplash-associated disorders (WAD) and to suggest directions for future research. There is divergence of opinion, primary research findings, and systematic reviews on the role of compensation and/or compensation-related factors in WAD recovery. The topic of research of compensation/compensation-related factors was discussed at an international summit meeting of 21 researchers from diverse fields of scientific enquiry. This article summarizes the main points raised in that discussion. Traffic injury compensation is a complex sociopolitical construct, which varies widely across jurisdictions. This leads to conceptual and methodological challenges in conducting and interpreting research in this area. It is important that researchers and their audiences be clear about what aspect of the compensation system is being addressed, what compensation-related variables are being studied, and what social/economic environment the compensation system exists in. In addition, summit participants also recommended that nontraditional, sophisticated study designs and analysis strategies be employed to clarify the complex causal pathways and mechanisms of effects. Care must be taken by both researchers and their audiences not to overgeneralize or confuse different aspects of WAD compensation. In considering the role of compensation/compensation-related factors on WAD and WAD recovery, it is important to retain a broad-based conceptualization of the range of biological, psychological, social, and economic factors that combine and interact to define and determine how people recover from WAD.

  14. Adaptive compensation control for attitude adjustment of quad-rotor unmanned aerial vehicle.

    Song, Zhankui; Sun, Kaibiao

    2017-07-01

    A compensation control strategy based on adaptive back-stepping technique is presented to address the problem of attitude adjustment for a quad-rotor unmanned aerial vehicle (QR- UAV) with inertia parameter uncertainties, the limited airflow disturbance and the partial loss of rotation speed effectiveness. In the design process of control system, adaptive estimation technique is introduced into the closed loop system in order to compensate the lumped disturbance term. More specifically, the designed controller utilizes "prescribed performance bounds" method, and therefore guarantees the transient performance of tracking errors, even in the presence of the lumped disturbance. Adaptive compensation algorithms under the proposed closed loop system structure are derived in the sense of Lyapunov stability analysis such that the attitude tracking error converge to a small neighborhood of equilibrium point. Finally, the simulation results demonstrate the effectiveness of the proposed controller. Copyright © 2017 ISA. Published by Elsevier Ltd. All rights reserved.

  15. Comparative experiments regarding approaches to feedforward hysteresis compensation for piezoceramic actuators

    Gu, Guo-Ying; Zhu, Li-Min

    2014-01-01

    Piezoceramic actuators (PCAs) are desired devices in many micro/nano-positioning applications. The performance of PCA-based applications is severely limited by the presence of hysteresis nonlinearity. To remedy the hysteresis nonlinearity in such systems, feedforward hysteresis compensation is the most common technique. In the literature, many different feedforward hysteresis compensation approaches have been developed, but there are no comparative studies of these approaches. Focusing on the modified Prandtl-Ishlinskii model (MPIM) for asymmetric hysteresis description of piezoceramic actuators, three feedforward hysteresis compensation approaches—inverse hysteresis compensation (IHC), without inverse hysteresis compensation (WIHC), and direct inverse hysteresis compensation (DIHC)—are developed and compared in this paper. Extensive comparative experiments were conducted on a PCA-actuated stage to verify the effectiveness of the three different feedforward control approaches to hysteresis compensation. The experimental results show that the performances among the three approaches are rather similar, and the main differences among them are due to the specific implementation of each approach. (paper)

  16. Neuroendocrine and renal effects of intravascular volume expansion in compensated heart failure

    Gabrielsen, A; Bie, P; Holstein-Rathlou, N H

    2001-01-01

    To examine if the neuroendocrine link between volume sensing and renal function is preserved in compensated chronic heart failure [HF, ejection fraction 0.29 +/- 0.03 (mean +/- SE)] we tested the hypothesis that intravascular and central blood volume expansion by 3 h of water immersion (WI) elicits...... sustained angiotensin-converting enzyme inhibitor therapy, n = 9) absolute and fractional sodium excretion increased (P Renal free water clearance increased during WI in control subjects but not in HF......, albeit plasma vasopressin concentrations were similar in the two groups. In conclusion, the neuroendocrine link between volume sensing and renal sodium excretion is preserved in compensated HF. The natriuresis of WI is, however, modulated by the prevailing ANG II and Aldo concentrations. In contrast...

  17. Digitally compensated beam current transformer

    Kesselman, Martin

    2005-01-01

    The Spallation Neutron Source (SNS) is being built by a collaboration of six laboratories. Beam current monitors (BCMs) will be used to record the current of H-minus and H-plus beams ranging from 15 mA (tune-up in the Front End and Linac) to over 60A fully accumulated in the Ring and dumped to the load as a single pulse in the Ring to Beam Target (RTBT). The time structure of these beams ranges from 645 ns 'mini' bunches at the 1.05 MHz ring revolution rate, to an overall 1 ms long macro-pulse. The requirements for the BCMs will depend upon their location within the system. The need to measure individual mini-pulses, examine the characteristics of the chopper edge, as well as the longer average current pulse of the macropulse, or long duration pulses during Linac tuning place wide requirements upon the response of current transformers. To obtain the desired accuracy and resolution, current transformers must have <1 ns rise time and droops of 0.1%/ms. This places a significant design burden on the current transformer; such a design is almost impossible to achieve. Extremely large expensive cores are needed to meet the low droop, while leakage inductance increases with size, thereby reducing the achievable rise time. In this paper, I discuss a digital compensation approach [M. Kesselman, Spallation neutron source beam current monitor electronics, PAC2001 June 18-22, 2001, Chicago, IL.] that extends the lower cut-off frequency of the current transformer, optimized for high frequency response, so that it can be used in this application with improvements in droop of the order of 1000:1. Transformer saturation (current-time product) is a separate issue and the transformer must be designed to handle the current-time product of the signal to assure it does not saturate

  18. Towards Compensation Correctness in Interactive Systems

    Vaz, Cátia; Ferreira, Carla

    One fundamental idea of service-oriented computing is that applications should be developed by composing already available services. Due to the long running nature of service interactions, a main challenge in service composition is ensuring correctness of failure recovery. In this paper, we use a process calculus suitable for modelling long running transactions with a recovery mechanism based on compensations. Within this setting, we discuss and formally state correctness criteria for compensable processes compositions, assuming that each process is correct with respect to failure recovery. Under our theory, we formally interpret self-healing compositions, that can detect and recover from failures, as correct compositions of compensable processes.

  19. Inductive voltage compensation in superconducting magnet systems

    Yeh, H.T.; Goddard, J.S.; Shen, S.S.

    1979-01-01

    This paper details several techniques of inductive voltage compensation developed for quench detection in superconducting magnet systems with multiple coils and power supplies, with particular application for the Large Coil Test Facility (LCTF). Sources of noise, their magnitudes, and the sensitivity required for normal zone detection to avoid damage to the magnets are discussed. Two passive compensation schemes (second difference and central difference) are introduced and illustrated by parameters of LCTF; these take advantage of coil symmetries and other system characteristics. An active compensation scheme based on current rate input fom pickup coils and utilizing theory on ac loss voltage for calibration was tested, and the experimental setup and test results are discussed

  20. Plasmonic sensing

    Mogensen, Klaus Bo

    2015-01-01

    Plasmonic sensors typically rely on detection of changes in the refractive index of the surrounding medium. Here, an alternative approach is reported based on electrical surface screening and controlled dissolution of ultrasmall silver nanoparticles (NPs; R ... in the plasmon band. This is demonstrated by using the strong nucleophiles, cyanide and cysteamine, as ligands. The “dissolution paths” in terms of peak wavelength and amplitude shifts differ significantly between different types of analytes, which are suggested as a means to obtain selectivity of the detection...... that cannot be obtained by traditional refractive index sensing, without the use of bioprobes. A simple modified Drude model is used to account for shifts in the plasmon band position due to electrical charging. Here, a screening parameter is introduced in the expression for the free electron density...

  1. Health Insurance Costs and Employee Compensation: Evidence from the National Compensation Survey.

    Anand, Priyanka

    2017-12-01

    This paper examines the relationship between rising health insurance costs and employee compensation. I estimate the extent to which total compensation decreases with a rise in health insurance costs and decompose these changes in compensation into adjustments in wages, non-health fringe benefits, and employee contributions to health insurance premiums. I examine this relationship using the National Compensation Survey, a panel dataset on compensation and health insurance for a sample of establishments across the USA. I find that total hourly compensation reduces by $0.52 for each dollar increase in health insurance costs. This reduction in total compensation is primarily in the form of higher employee premium contributions, and there is no evidence of a change in wages and non-health fringe benefits. These findings show that workers are absorbing at least part of the increase in health insurance costs through lower compensation and highlight the importance of examining total compensation, and not just wages, when examining the relationship between health insurance costs and employee compensation. Copyright © 2016 John Wiley & Sons, Ltd. Copyright © 2016 John Wiley & Sons, Ltd.

  2. Focusing Optics for High-Energy X-ray Diffraction

    Leinert, U.; Schulze, C.; Honkimäki, V.

    1998-01-01

    Novel focusing optical devices have been developed for synchrotron radiation in the energy range 40-100 keV. Firstly, a narrow-band-pass focusing energy-tuneable fixed-exit monochromator was constructed by combining meridionally bent Laue and Bragg crystals. Dispersion compensation was applied...

  3. Dynamic Nonreciprocity in Loss-Compensated Piezophononic Media

    Merkel, Aurélien; Willatzen, Morten; Christensen, Johan

    2018-03-01

    Violating time-reversal symmetry enables one to engineer nonreciprocal structures for isolating and rectifying sound and mechanical vibrations. Rectifying sound is commonly achieved in nonlinear media, but the operation is inherently linked to weak and distorted signals. Here, we show how a pronounced electron-phonon coupling in linear piezophononic media under electrical bias can generate full mechanical rectification of broad spectral width, which permits the isolation of pulsed vibrations while keeping the wave-front shape fully intact. In this context, we deliberately show how the acoustoelectric effect can provide active loss compensation against lattice anharmonicity and thermoelastic damping. Further, our predictions confirm tunable nonreciprocity at an ultralarge contrast ratio, which should open the doors for future mechanical diodes and compact ultrasonic transducers for sensing and imaging.

  4. Compensation neurosis: financial reward for illness as nocebo.

    Bellamy, R

    1997-03-01

    Results of medical treatment are notoriously poor in patients with pending litigation after personal injury or disability claims, and for those covered by workers' compensation programs. Although some instances of overt malingering are documented by surveillance videos, most exaggerated illness behavior in compensation situations takes place because of a combination of suggestion, somatization, and rationalization. A distorted sense of justice, victim status, and entitlement may further the exaggerated sick role. Adversarial administrative and legal systems challenging the claimant to prove repeatedly he or she is permanently ill harden the conviction of illness and the individual's defense of the claim. Unfortunately, after advocating for one's injury before a sometimes doubting public for the several years required to resolve such claims, care eliciting behavior too often remains permanent. Because any improvement in the claimant's health condition may result in denial of disability status in the future, the claimant is compelled to guard against getting well and is left with no honorable way to recover from illness. Financial reward for illness thus functions as a powerful nocebo, a nonspecific force creating and exacerbating illness. Solutions require recognition that judging disability and work incapacity in others is an unscientific process and that adversarial systems rewarding permanent illness or injury, particularly self reported pain, are often permanently harmful. The remainder of the solution must be political.

  5. Translation compensation and micro-Doppler extraction for precession ballistic targets with a wideband terahertz radar

    Yang, Qi; Deng, Bin; Wang, Hongqiang; Zhang, Ye; Qin, Yuliang

    2018-01-01

    Imaging, classification, and recognition techniques of ballistic targets in midcourse have always been the focus of research in the radar field for military applications. However, the high velocity translation of ballistic targets will subject range profile and Doppler to translation, slope, and fold, which are especially severe in the terahertz region. Therefore, a two-step translation compensation method based on envelope alignment is presented. The rough compensation is based on the traditional envelope alignment algorithm in inverse synthetic aperture radar imaging, and the fine compensation is supported by distance fitting. Then, a wideband imaging radar system with a carrier frequency of 0.32 THz is introduced, and an experiment on a precession missile model is carried out. After translation compensation with the method proposed in this paper, the range profile and the micro-Doppler distributions unaffected by translation are obtained, providing an important foundation for the high-resolution imaging and micro-Doppler extraction of the terahertz radar.

  6. Making Sense of Extraneous Solutions

    Zelkowski, Jeremy S.

    2013-01-01

    Principles and Standards for School Mathematics (NCTM 2000) states, "Technology is essential in teaching and learning mathematics; it influences the mathematics that is taught and enhances students' learning." The focus on reasoning and sense making with technology in the lesson presented in this article will enable students to do more…

  7. The risks and rewards of setting physician compensation internally.

    Johnson, Jen

    2013-01-01

    To establish physician compensation internally, finance leaders should: Educate decision makers on basic regulatory guidance and valuation theory. Determine fair market value. Consider using a compensation calculator.

  8. Comprehensive Environmental Response, Compensation and Liability Act

    National Oceanic and Atmospheric Administration, Department of Commerce — This data represents geographic terms used within the Comprehensive Environmental Response, Compensation, and Liability Act (CERCLA). CERCLA, commonly known as...

  9. Defense Contract Audit Agency Compensation Audits

    1999-01-01

    .... The Defense Contract Audit Agency (DCAA) assists the administrative contracting officer in accomplishing that responsibility by determining whether the contractor's compensation system is sound, reliable, consistently applied, and results...

  10. Mandatory Compensation to Commercial Agents upon Termination ...

    Kamil Abdu Oumer

    the compensation due to the agent upon the termination of the commercial .... Virginia School of Law Legal Studies Working Papers Series, Working Paper No. ..... grant up to a one year commission if they find the circumstances equitable.67 In.

  11. Shaft Seal Compensates for Cold Flow

    Myers, W. N.; Hein, L. A.

    1985-01-01

    Seal components easy to install. Ring seal for rotating or reciprocating shafts spring-loaded to compensate for slow yielding (cold flow) of sealing material. New seal relatively easy to install because components preassembled, then installed in one piece.

  12. Integrated open source mine workers compensation system

    Coetzee, L

    2006-08-01

    Full Text Available This article describes the Mine Workers Compensation System developed by the CSIR and Molepe Consulting for the South African Department of Health. Mining activities increase the risk of certain occupational lung diseases. South African legislation...

  13. Convention on supplementary compensation for nuclear damage

    NONE

    1998-07-22

    The document reproduces the text of the Convention on Supplementary Compensation for Nuclear Damage which was adopted on 12 September 1997 by a Diplomatic Conference held between 8-12 September 1997 in Vienna

  14. voltage compensation using artificial neural network

    Offor Theophilos

    Simulation results showed that DVR is effective in compensating for ... shutdown of heavy equipment, switching operations etc, ... station were carried out in MatLab 2013 application. ... semiconductor in a pulse width modulation (PWM).

  15. Convention on supplementary compensation for nuclear damage

    1998-01-01

    The document reproduces the text of the Convention on Supplementary Compensation for Nuclear Damage which was adopted on 12 September 1997 by a Diplomatic Conference held between 8-12 September 1997 in Vienna

  16. Increasing of AC compensation method accuracy

    Havlicek, V.; Pokorny, M.

    2003-01-01

    The original MMF compensation method allows the magnetic properties of single sheets and strips to be measured in the same way as the closed specimen properties. The accuracy of the method is limited due to the finite gain of the feedback loop fulfilling the condition of its stability. Digitalisation of the compensation loop appropriate processing of the error signal can rapidly improve the accuracy. The basic ideas of this new approach and the experimental results are described in this paper

  17. Increasing of AC compensation method accuracy

    Havlíček, V.; Pokorný, M.

    2003-01-01

    The original MMF compensation method allows the magnetic properties of single sheets and strips to be measured in the same way as the closed specimen properties. The accuracy of the method is limited due to the finite gain of the feedback loop fulfilling the condition of its stability. Digitalisation of the compensation loop appropriate processing of the error signal can rapidly improve the accuracy. The basic ideas of this new approach and the experimental results are described in this paper.

  18. Radiotherapy dose compensation for lung patients

    Piyaratna, N.; Arnold, A.; Metcalfe, P.

    1999-01-01

    The purpose of the present paper is to provide a more homogeneous dose distribution in the target volume from compensated anterior and posterior fields while the healthy lung is spared by de-weighting the lateral fields. A compensation computation which used linear iterations to compute the most homogeneous dose distribution across the target volume was applied to produce optimum compensator designs. The equivalent tissue-air ratio (E-TAR) inhomogeneity correction was applied for the computations using a GE target series 11 planning computer. The compensators designed were tested for accuracy in a modified water/lung phantom using a scanning diode and an anthropomorphic phantom using thermoluminescent dosimeters. A comparison has been made between the compensated and uncompensated plans for the first nine patients who we have treated with this technique. The dose profiles produced by the computation agreed with the prediction of the computed isodose plans to within ± 2% at the target depth. The thermoluminescent dosimeter (TLD)-measured results in the anthropomorphic phantom agreed with the planning computer within ± 3%. A comparison of nine compensated plans of radiotherapy patients for large-volume targets in the lung region showed a maximum variation in the target to be 19% uncompensated versus 10% compensated. By providing compensated treatment fields from anterior and posterior treatment portals, a homogeneous dose that conforms well to the target volume is provided. As an added bonus, this enables the lateral lung fields to be significantly de-weighted and the healthy lung is spared considerable dose. Copyright (1999) Blackwell Science Pty Ltd

  19. Reversible thyristor converters of brushless synchronous compensators

    А.М.Galynovskiy

    2013-12-01

    Full Text Available Behavior of models of three-phase-to-single-phase rotary reversible thyristor converters of brushless synchronous compensators in a circuit simulation system is analyzed. It is shown that combined control mode of opposite-connected thyristors may result in the exciter armature winding short circuits both at the thyristor feed-forward and lagging current delay angles. It must be taken into consideration when developing brushless compensator excitation systems.

  20. Executive Compensation and Principal-Agent Theory.

    Garen, John E

    1994-01-01

    The empirical literature on executive compensation generally fails to specify a model of executive pay on which to base hypotheses regarding its determinants. In contrast, this paper analyzes a simple principal-agent model to determine how well it explains variations in CEO incentive pay and salaries. Many findings are consistent with the basic intuition of principle-agent models that compensation is structured to trade off incentives with insurance. However, statistical significance for some...

  1. Stock Option Compensation and Managerial Turnover

    Raluca Georgiana NASTASESCU

    2009-01-01

    This study examines the association between managerial turnover and equity-based compensation. I investigate whether stock options act to bond executives to their firms and whether retention of managers is a motivation of companies in designing CEO incentive contracts. The results show that stock options do negatively influence the probability of a CEO leaving the company. The monetary cost of losing the value of equity-based compensation package keeps the manager with his company. I also fin...

  2. Compensation for Combat Deaths: Policy Considerations

    2012-01-01

    through the courts for deaths resulting from other parties’ negligence or criminal behavior; a key difference between the tort system and many other...funding facilities that function outside of the tort system— for example, workers’ compensation programs for workplace fatalities and the Victims...receive $100,000 if the 10-percent risk of a loss of $100,000 actually came to pass. Tort law generally uses an ex post approach to compensation and

  3. Reactive power compensation a practical guide

    Hofmann, Wolfgang; Just, Wolfgang

    2012-01-01

    The comprehensive resource on reactive power compensation, presenting the design, application and operation of reactive power equipment and installations The area of reactive power compensation is gaining increasing importance worldwide. If suitably designed, it is capable of improving voltage quality significantly, meaning that losses in equipment and power systems are reduced, the permissible loading of equipment can be increased, and the over-all stability of system operation improved. Ultimately, energy use and CO2 emisson are reduced. This unique guide discusses the

  4. Magnetic susceptibility measuring probe utilizing a compensation coil

    Bonnet, Jean; Fournet, Julien.

    1978-01-01

    This invention concerns a magnetic susceptibility measuring probe. It is used, inter alia, in logging, to wit continuous logging of the magnetic susceptibility of the ground throughout the length of a bore hole. The purpose of this invention is to increase the sensitivity of this type of probe by creating a side focusing effect . To this end, it provides for the use of a compensation winding, coaxial with the measurement winding and arranged symmetrically to the latter with respect to the centre of the induction windings [fr

  5. Analysis of multichannel optical rotary connectors based on the compensation operating principle with mirror and prismatic optical compensators (Part 1

    V.M. Shapar

    2017-04-01

    Full Text Available Performed in this work is a comprehensive theoretical computer analysis of performances inherent to two types of multichannel optical rotary connectors (ORC of compensation operation based on mirror and prismatic compensators. This analysis relies on exact analytical expressions obtained for light ray paths in ORC models with a mirror compensator made in the form of bilateral mirror placed between two optical hemispheres and with prismatic compensator made in the form of Dove prism placed between two non-aberrational elliptic lenses. Found in ORC with the mirror compensator is the essential deficiency inherent to all these constructions, which is related with considerable rotary oscillations in the value of optical signals in mirror angular positions when the mirror halves the input light beam. In these mirror positions, the amplitude value of optical signal oscillations exceeds 95%, and optical losses are higher than –13 dB, when the rotor turns. One deficiency more in these constructions is also strict technical requirements to the accuracy of making the optical components and mechanisms at the level of 1…2 µm. Concerning the ORC construction with a prismatic compensator as well as collimator and focusing lenses common for all the channels, one should note the inadmissibly high optical losses of the signal value (higher than –30…40 dB in the case of construction with fiber-optic interfaces, and large dimensions and mass in the case of active construction with optoelectronic transducers at the inputs and outputs of ORC. For example, when the number of channels N = 10 the longitudinal dimension of optical transfer channel (prism and lenses exceeds 300 mm, and this dimension increases with increasing the number of channels. When this dimension is lower than 100 mm, the facility can be equipped with only one optical communication channel containing one LED and one photodiode located on the rotation axis. Optical losses in these

  6. Environmental change, phenotypic plasticity, and genetic compensation.

    Grether, Gregory F

    2005-10-01

    When a species encounters novel environmental conditions, some phenotypic characters may develop differently than in the ancestral environment. Most environmental perturbations of development are likely to reduce fitness, and thus selection would usually be expected to favor genetic changes that restore the ancestral phenotype. I propose the term "genetic compensation" to refer to this form of adaptive evolution. Genetic compensation is a subset of genetic accommodation and the reverse of genetic assimilation. When genetic compensation has occurred along a spatial environmental gradient, the mean trait values of populations in different environments may be more similar in the field than when representatives of the same populations are raised in a common environment (i.e., countergradient variation). If compensation is complete, genetic divergence between populations may be cryptic, that is, not detectable in the field. Here I apply the concept of genetic compensation to three examples involving carotenoid-based sexual coloration and then use these and other examples to discuss the concept in a broader context. I show that genetic compensation may lead to a cryptic form of reproductive isolation between populations evolving in different environments, may explain some puzzling cases in which heritable traits exposed to strong directional selection fail to show the expected evolutionary response, and may complicate efforts to monitor populations for signs of environmental deterioration.

  7. Intensity modulated radiotherapy (IMRT) with compensators

    Salz, H.; Wiezorek, T.; Scheithauer, M.; Kleen, W.; Schwedas, M.; Wendt, T.G.

    2002-01-01

    The irradiation with intensity-modulated fields is possible with static as well as dynamic methods. In our university hospital, the intensity-modulated radiotherapy (IMRT) with compensators was prepared and used for the first time for patient irradiation in July 2001. The compensators consist of a mixture of tin granulate and wax, which is filled in a milled negative mould. The treatment planning is performed with Helax-TMS (MDS Nordion). An additional software is used for editing the modulation matrix ('Modifix'). Before irradiation of the first patient, extensive measurements have been carried out in terms of quality assurance of treatment planning and production of compensators. The results of the verification measurements have shown that IMRT with compensators possesses high spatial and dosimetric exactness. The calculated dose distributions are applied correctly. The accuracy of the calculated monitor units is normally better than 3%; in small volumes, further dosimetric inaccuracies between calculated and measured dose distributions are mostly less than 3%. Therefore, the compensators contribute to the achievement of high-level IMRT even when apparatuses without MLC are used. This paper describes the use of the IMRT with compensators, presents the limits of this technology, and discusses the first practical experiences. (orig.) [de

  8. Sensing our Environment: Remote sensing in a physics classroom

    Isaacson, Sivan; Schüttler, Tobias; Cohen-Zada, Aviv L.; Blumberg, Dan G.; Girwidz, Raimund; Maman, Shimrit

    2017-04-01

    Remote sensing is defined as data acquisition of an object, deprived physical contact. Fundamentally, most remote sensing applications are referred to as the use of satellite- or aircraft-based sensor technologies to detect and classify objects mainly on Earth or other planets. In the last years there have been efforts to bring the important subject of remote sensing into schools, however, most of these attempts focused on geography disciplines - restricting to the applications of remote sensing and to a less extent the technique itself and the physics behind it. Optical remote sensing is based on physical principles and technical devices, which are very meaningful from a theoretical point of view as well as for "hands-on" teaching. Some main subjects are radiation, atom and molecular physics, spectroscopy, as well as optics and the semiconductor technology used in modern digital cameras. Thus two objectives were outlined for this project: 1) to investigate the possibilities of using remote sensing techniques in physics teaching, and 2) to identify its impact on pupil's interest in the field of natural sciences. This joint project of the DLR_School_Lab, Oberpfaffenhofen of the German Aerospace Center (DLR) and the Earth and Planetary Image Facility (EPIF) at BGU, was conducted in 2016. Thirty teenagers (ages 16-18) participated in the project and were exposed to the cutting edge methods of earth observation. The pupils on both sides participated in the project voluntarily, knowing that at least some of the project's work had to be done in their leisure time. The pupil's project started with a day at EPIF and DLR respectively, where the project task was explained to the participants and an introduction to remote sensing of vegetation was given. This was realized in lectures and in experimental workshops. During the following two months both groups took several measurements with modern optical remote sensing systems in their home region with a special focus on flora

  9. Comparisons of lesion detectability in ultrasound images acquired using time-shift compensation and spatial compounding.

    Lacefield, James C; Pilkington, Wayne C; Waag, Robert C

    2004-12-01

    The effects of aberration, time-shift compensation, and spatial compounding on the discrimination of positive-contrast lesions in ultrasound b-scan images are investigated using a two-dimensional (2-D) array system and tissue-mimicking phantoms. Images were acquired within an 8.8 x 12-mm2 field of view centered on one of four statistically similar 4-mm diameter spherical lesions. Each lesion was imaged in four planes offset by successive 45 degree rotations about the central scan line. Images of the lesions were acquired using conventional geometric focusing through a water path, geometric focusing through a 35-mm thick distributed aberration phantom, and time-shift compensated transmit and receive focusing through the aberration phantom. The views of each lesion were averaged to form sets of water path, aberrated, and time-shift compensated 4:1 compound images and 16:1 compound images. The contrast ratio and detectability index of each image were computed to assess lesion differentiation. In the presence of aberration representative of breast or abdominal wall tissue, time-shift compensation provided statistically significant improvements of contrast ratio but did not consistently affect the detectability index, and spatial compounding significantly increased the detectability index but did not alter the contrast ratio. Time-shift compensation and spatial compounding thus provide complementary benefits to lesion detection.

  10. Making sense of project management

    Kjærgaard, Annemette; Kautz, Karl; Nielsen, Peter Axel

    2007-01-01

    How can a software company make sense of project management when it becomes involved in software process improvement? In software development most research has an instrumental view of knowledge management thus neglecting what is probably the most important part of knowledge management namely making...... sense of practice by developers and project managers. Through an action case, we study the knowledge management processes in a Danish software company. We analyse the case through the lens of a theoretical framework. The theoretical framework focuses in particular on sensemaking, collective construed...... substantial insight which could not have been achieved through an instrumental perspective on knowledge management....

  11. 28 CFR 104.21 - Filing for compensation.

    2010-07-01

    ... “Personal Injury Compensation Form” or a “Death Compensation Form.” A claim shall be deemed “filed” for... filing either a “Personal Injury Compensation Form” or a “Death Compensation Form,” the claim shall be..., when a Claims Evaluator determines that both the Eligibility Form and either a Personal Injury...

  12. 20 CFR 211.2 - Definition of compensation.

    2010-04-01

    ... 20 Employees' Benefits 1 2010-04-01 2010-04-01 false Definition of compensation. 211.2 Section 211.2 Employees' Benefits RAILROAD RETIREMENT BOARD REGULATIONS UNDER THE RAILROAD RETIREMENT ACT CREDITABLE RAILROAD COMPENSATION § 211.2 Definition of compensation. (a) The term compensation means any form...

  13. 50 CFR 296.4 - Claims eligible for compensation.

    2010-10-01

    ... compensation. (a) Claimants. Damage or loss eligible for Fund compensation must be suffered by a commercial fisherman. (b) Damage or loss of fishing gear. Damage or loss is eligible for Fund compensation if it was... is not eligible for Fund compensation: (1) If the damage or loss was caused by the negligence or...

  14. 38 CFR 3.5 - Dependency and indemnity compensation.

    2010-07-01

    ... 38 Pensions, Bonuses, and Veterans' Relief 1 2010-07-01 2010-07-01 false Dependency and indemnity... ADJUDICATION Pension, Compensation, and Dependency and Indemnity Compensation General § 3.5 Dependency and indemnity compensation. (a) Dependency and indemnity compensation. This term means a monthly payment made by...

  15. Is Trust for Sale? The Effectiveness of Financial Compensation for Repairing Competence- versus Integrity-Based Trust Violations

    Haesevoets, Tessa; Reinders Folmer, Chris; Van Hiel, Alain

    2015-01-01

    Despite the popularity of financial compensation as a means for addressing trust violations, the question whether (more) money can indeed buy trust back remains largely unexplored. In the present research, we focus on the role of violation type and compensation size. The results of a scenario study and a laboratory experiment show that financial compensation can effectively promote the restoration of trust for transgressions that indicate a lack of competence. Conversely, for transgressions which signal a lack of integrity, financial compensation is not an effective tool to repair trust. Moreover, our findings indicate that for both violation types, overcompensation has no positive effects on top of the impact of equal compensation. These findings therefore show that when it comes to trust, money cannot buy everything. PMID:26714025

  16. Defining Compensable Injury in Biomedical Research.

    Larkin, Megan E

    2015-01-01

    Biomedical research provides a core social good by enabling medical progress. In the twenty-first century alone, this includes reducing transmission of HIV/AIDS, developing innovative therapies for cancer patients, and exploring the possibilities of personalized medicine. In order to continue to advance medical science, research relies on the voluntary participation of human subjects. Because research is inherently uncertain, unintended harm is an inevitable part of the research enterprise. Currently, injured research participants in the United States must turn to the “litigation lottery” of the tort system in search of compensation. This state of affairs fails research participants, who are too often left uncompensated for devastating losses, and makes the United States an outlier in the international community. In spite of forty years’ worth of Presidential Commissions and other respected voices calling for the development of a no-fault compensation system, no progress has been made to date. One of the reasons for this lack of progress is the failure to develop a coherent ethical basis for an obligation to provide compensation for research related injuries. This problem is exacerbated by the lack of a clear definition of “compensable injury” in the biomedical research context. This article makes a number of important contributions to the scholarship in this growing field. To begin, it examines compensation systems already in existence and concludes that there are four main definitional elements that must be used to define “compensable injury.” Next, it examines the justifications that have been put forth as the basis for an ethical obligation to provide compensation, and settles on retrospective nonmaleficence and distributive and compensatory justice as the most salient and persuasive. Finally, it uses the regulatory elements and the justifications discussed in the first two sections to develop a well-rounded definition of “compensable injury

  17. Advanced sensing techniques for cognitive radio

    Zhao, Guodong; Li, Shaoqian

    2017-01-01

    This SpringerBrief investigates advanced sensing techniques to detect and estimate the primary receiver for cognitive radio systems. Along with a comprehensive overview of existing spectrum sensing techniques, this brief focuses on the design of new signal processing techniques, including the region-based sensing, jamming-based probing, and relay-based probing. The proposed sensing techniques aim to detect the nearby primary receiver and estimate the cross-channel gain between the cognitive transmitter and primary receiver. The performance of the proposed algorithms is evaluated by simulations in terms of several performance parameters, including detection probability, interference probability, and estimation error. The results show that the proposed sensing techniques can effectively sense the primary receiver and improve the cognitive transmission throughput. Researchers and postgraduate students in electrical engineering will find this an exceptional resource.

  18. Temperature compensation and entrainment in circadian rhythms

    Bodenstein, C; Heiland, I; Schuster, S

    2012-01-01

    To anticipate daily variations in the environment and coordinate biological activities into a daily cycle many organisms possess a circadian clock. In the absence of external time cues the circadian rhythm persists with a period of approximately 24 h. The clock phase can be shifted by single pulses of light, darkness, chemicals, or temperature and this allows entrainment of the clock to exactly 24 h by cycles of these zeitgebers. On the other hand, the period of the circadian rhythm is kept relatively constant within a physiological range of constant temperatures, which means that the oscillator is temperature compensated. The mechanisms behind temperature compensation and temperature entrainment are not fully understood, neither biochemically nor mathematically. Here, we theoretically investigate the interplay of temperature compensation and entrainment in general oscillatory systems. We first give an analytical treatment for small temperature shifts and derive that every temperature-compensated oscillator is entrainable to external small-amplitude temperature cycles. Temperature compensation ensures that this entrainment region is always centered at the endogenous period regardless of possible seasonal temperature differences. Moreover, for small temperature cycles the entrainment region of the oscillator is potentially larger for rectangular pulses. For large temperature shifts we numerically analyze different circadian clock models proposed in the literature with respect to these properties. We observe that for such large temperature shifts sinusoidal or gradual temperature cycles allow a larger entrainment region than rectangular cycles. (paper)

  19. Engineering Compensations in Web Service Environment

    Schäfer, Micahel; Dolog, Peter; Nejdl, Wolfgang

    2007-01-01

    Business to business integration has recently been performed by employing Web service environments. Moreover, such environments are being provided by major players on the technology markets. Those environments are based on open specifications for transaction coordination. When a failure in such a......Business to business integration has recently been performed by employing Web service environments. Moreover, such environments are being provided by major players on the technology markets. Those environments are based on open specifications for transaction coordination. When a failure...... in such an environment occurs, a compensation can be initiated to recover from the failure. However, current environments have only limited capabilities for compensations, and are usually based on backward recovery. In this paper, we introduce an engineering approach and an environment to deal with advanced...... compensations based on forward recovery principles. We extend the existing Web service transaction coordination architecture and infrastructure in order to support flexible compensation operations. A contract-based approach is being used, which allows the specification of permitted compensations at runtime. We...

  20. Compensation and exotic livestock disease management: the views of animal keepers and veterinarians in England.

    Hamilton-Webb, A; Naylor, R; Little, R; Maye, D

    2016-11-19

    Relatively little is known about the perceived influence of different compensation systems on animal keepers' management of exotic livestock disease. This paper aims to address this research gap by drawing on interviews with 61 animal keepers and 21 veterinarians, as well as a series of nine animal keeper focus groups across five different livestock sectors in England. The perceived influence of current compensation systems on disease control behaviour was explored and alternative compensation systems that respectively reward positive practices and penalise poor practices were presented in the form of scenarios, alongside a third system that considered the option of a cost-sharing levy system between industry and government. The results indicate that animal keepers consider themselves to be influenced by a range of non-financial factors, for example, feelings of responsibility, reputation and animal welfare concerns, in the context of their exotic disease management practices. The majority of animal keepers were unaware of the current compensation systems in place for exotic diseases, and were therefore not consciously influenced by financial recompense. Concerns were raised about linking compensation to disease management behaviour due to auditing difficulties. A cost-sharing levy system would likely raise awareness of exotic disease and compensation among animal keepers, but differentiation of payments based upon individual farm-level risk assessments was called for by participants as a strategy to promote positive disease management practices. British Veterinary Association.

  1. A scientometric review of emerging trends and new developments in agricultural ecological compensation.

    He, Ke; Zhang, Junbiao; Wang, Xueting; Zeng, Yangmei; Zhang, Lu

    2018-05-08

    Agricultural ecological compensation has drawn an increasingly broad range of interest since early 1990s. In recent years, the volume of the literature grows rapidly. As a result, a systematic review of the diverse research field and its current trends becomes essential. This paper surveys the literature of agricultural ecological compensation between 1990 and 2016. Specifically, by employing CiteSpace information visualization software, we firstly identified the research hotspots and evolution path and then illustrated the frontier and developing trend of the domain in core and broader perspectives. It is found that the focus of the academic community has always been researches on the theoretical policy and application of the payment for agro-ecosystem services, agricultural ecological compensation based on contingent valuation method, and ecological compensation of farmland landscape and organic food production as well as willingness to accept/pay for land use and ecological protection. Meanwhile, we also found that, in recent years, qualitative research has received more and more attention in the field of agricultural ecological compensation, since global warming, agricultural carbon emissions, and other emerging environmental issues have aroused widespread concern of the people around the world. Moreover, we believed that more and more scholars will employ case study methodology to analyze agricultural ecological compensation in specific systems, regions, or circumstances in the future.

  2. Person-based differences in pay reactions: A compensation-activation theory and integrative conceptual review.

    Fulmer, Ingrid Smithey; Shaw, Jason D

    2018-06-07

    Compensation research has focused traditionally on how pay design characteristics (e.g., pay level, individual or group incentives) relate to average employee outcomes and, in toto, on how these outcomes affect organizational performance. Recently, scholars have begun to pay more attention to how individuals vary in the strength of their reactions to pay. Empirical research in several disciplines examines how the interplay of pay systems and person-based characteristics (psychological individual differences, demographics, and relative performance or position in a group) relate to important work-related outcomes. We develop a compensation-activation theory that frames compensation design characteristics as workplace "situations" providing cues that activate individuals' corresponding fundamental social motives made salient due to chronic or transient person-based characteristics. Where activation occurs, stronger-than-average responses to the compensation "situation" are expected. Using the theory as a lens, we synthesize and reinterpret existing research on person-based reactions to pay characteristics, including sorting, incentive/motivational effects, and effects on collective pay system reactions and unit/organizational outcomes. We conclude with a research agenda aimed at refining compensation-activation theory and advancing the study of compensation as it affects individual and organizational outcomes. (PsycINFO Database Record (c) 2018 APA, all rights reserved).

  3. Prevalence and predictors of posttraumatic stress disorder among victims of violence applying for state compensation.

    Kunst, Maarten; Winkel, Frans Willem; Bogaerts, Stefan

    2010-09-01

    Many studies have focused on the predictive value of victims' emotions experienced shortly after violence exposure to identify those vulnerable for development of posttraumatic stress disorder (PTSD). However, many victims remain unidentified during the initial recovery phase, yet may still be highly in need of psychological help after substantial time since victimization has passed. Professionals involved in the settlement of civil damage claims filed by victims of violence may play an important role in referring victims with current psychological problems to appropriate treatment services, as they are likely to maintain relations with victims until all compensation possibilities have been exhausted. As an exploratory examination of this topic, the current study investigates the potential utility of file characteristics as predictors of chronic PTSD among 686 victims of violence who had applied for state compensation with the Dutch Victim Compensation Fund (DVCF) in 2006. Identification of significant predictors is preceded by estimating prevalence rates of PTSD. Results indicate that approximately 1 of 2 victims applying for state compensation in the Netherlands still have PTSD many years after victimization and claim settlement. Age, female sex, time since victimization, acquaintance with the perpetrator, violence-related hospitalization, and compensation for immaterial damage prove to be predictive of PTSD, although female sex and immaterial damage compensation fail to reach significance after adjusting for recalled peritraumatic distress severity. Implications for policy practice as well as strengths and limitations of the study are discussed.

  4. Automatic device for compensating the earths, magnetic field around a {beta} spectrometer; Ensemble automatique de compensation du champ terrestre autour d'un spectrometre

    Ristori, Ch [Commissariat a l' Energie Atomique, Grenoble (France). Centre d' Etudes Nucleaires

    1967-02-15

    This paper shows how the earth magnetic field inside a double focusing, {pi}{radical}2, iron free, beta ray spectrometer (radius 50 cm ) has been compensated. Three orthogonal magnetic fields are generated by three square coils sets. Each stabilized power supply is regulated through its own magnetometer (of the fluxgate type) and the earth field inside the spectrometer is compensated to 10{sup -4} Oe whatever the earth field or power supply oscillation could be. (author) [French] Cette etude a pour but de compenser le champ magnetique terrestre autour d'un spectrometre beta {pi}{radical}2 a double focalisation, a bobines sans fer et de rayon moyen des trajectoires de 50 cm. Le champ magnetique terrestre est compense par superposition de trois champs orthogonaux, chacun cree par un ensemble de cadres carres. Chacune de ces composantes est mesuree par un magnetometre. Cet ensemble permet de travailler en regulation de courant ou en regulation de champ. En regulation de courant, l'operation est manuelle. En regulation de champ, pour chaque groupe de cadres, l'alimentation stabilisee est asservie par son magnetometre et malgre les variations du champ terrestre ou de la tension secteur, la compensation du champ terrestre se fait toujours correctement au niveau du spectrometre, a 10{sup -4} Oe pres. (auteur)

  5. Sense of humor at work: assessment and associations with health

    Doosje, S.

    2010-01-01

    This dissertation is about health-related sense of humor measurement and associations between a sense of humor and health. Two sense of humor measures were developed, the QOHC and the HCL. The QOHC measures four humorous coping styles, aimed at acquiring positive affective states: antecedent-focused

  6. Passive temperature compensation in hydraulic dashpot used for the shut-off rod drive mechanism of a nuclear reactor

    Singh, Narendra K.; Badodkar, Deepak N.

    2015-01-01

    Highlights: • Passive temperature compensation in hydraulic dashpot has been studied numerically as well as experimentally. • Temperature compensation is achieved by reducing the clearances in the hydraulic dashpot at elevated temperature to compensate for the viscosity reduction. • Temperature compensation effects due to difference in thermal expansion of common engineering materials and use of bimetallic strips have been analyzed. • Design of a novel passive temperature compensating hydraulic dashpot is presented, which can be used for wide range of temperature variations. - Abstract: Passive temperature compensating hydraulic dashpot has been studied numerically as well as experimentally in this paper. Study is focused on reducing the clearances of the hydraulic dashpot at elevated temperature which intern compensates for the reduction in viscosity of damping oil and the dashpot gives uniform performance for wide range of temperature variation. Temperature compensation effects are mainly due to difference in the thermal expansion of materials. Different combinations of materials are used to reduce the dashpot clearances at elevated temperature. Finite element commercial code COMSOL Multiphysics 5.1 has been used for numerical analysis. Fluid-structure analysis has been carried-out to study the thermal expansion and pressure generated in the hydraulic dashpot. Multiphysics study with solid mechanics, laminar flow and moving mesh interfaces has been carried-out. Thermal expansion results of study-1 (solid mechanics) are further extended in to study-2 (laminar flow and moving mesh) and dashpot pressure is estimated. These results show that bimetallic strip improves the dashpot performance at 55 °C but do not fully compensate beyond that and less severe impacts occurs. Specific combinations of design and materials have been presented in this paper for obtaining maximum temperature compensation. A novel passive temperature compensating hydraulic dashpot

  7. Passive temperature compensation in hydraulic dashpot used for the shut-off rod drive mechanism of a nuclear reactor

    Singh, Narendra K., E-mail: nksingh_chikki@yahoo.com [Division of Remote Handling and Robotics, Bhabha Atomic Research Centre, Mumbai, 400085 (India); Badodkar, Deepak N. [Division of Remote Handling and Robotics, Bhabha Atomic Research Centre, Mumbai, 400085 (India); Homi Bhabha National Institute, Anushaktinagar, Mumbai, 400094 (India)

    2015-11-15

    Highlights: • Passive temperature compensation in hydraulic dashpot has been studied numerically as well as experimentally. • Temperature compensation is achieved by reducing the clearances in the hydraulic dashpot at elevated temperature to compensate for the viscosity reduction. • Temperature compensation effects due to difference in thermal expansion of common engineering materials and use of bimetallic strips have been analyzed. • Design of a novel passive temperature compensating hydraulic dashpot is presented, which can be used for wide range of temperature variations. - Abstract: Passive temperature compensating hydraulic dashpot has been studied numerically as well as experimentally in this paper. Study is focused on reducing the clearances of the hydraulic dashpot at elevated temperature which intern compensates for the reduction in viscosity of damping oil and the dashpot gives uniform performance for wide range of temperature variation. Temperature compensation effects are mainly due to difference in the thermal expansion of materials. Different combinations of materials are used to reduce the dashpot clearances at elevated temperature. Finite element commercial code COMSOL Multiphysics 5.1 has been used for numerical analysis. Fluid-structure analysis has been carried-out to study the thermal expansion and pressure generated in the hydraulic dashpot. Multiphysics study with solid mechanics, laminar flow and moving mesh interfaces has been carried-out. Thermal expansion results of study-1 (solid mechanics) are further extended in to study-2 (laminar flow and moving mesh) and dashpot pressure is estimated. These results show that bimetallic strip improves the dashpot performance at 55 °C but do not fully compensate beyond that and less severe impacts occurs. Specific combinations of design and materials have been presented in this paper for obtaining maximum temperature compensation. A novel passive temperature compensating hydraulic dashpot

  8. Sources of compensation in hadronic calorimeters

    Goodman, M.S.; Gabriel, T.A.; Di Ciaccio, A.; Wilson, R.

    1988-12-01

    Monte Carlo simulations are presented using the CALOR code system to study the design of a large hybrid hadron calorimeter system employing a warm liquid active medium (tetramethylsilane, Si(CH 3 ) 4 ) and uranium plates in addition to a conventional Fe/plastic system. In the system described here, the uranium provides partial compensation by suppressing the electromagnetic cascade produced by incident electrons due to sampling inefficiencies. The results of the simulations also indicate that significant compensation is achieved (given small enough saturation) due to low energy recoil protons produced in collisions with low energy (1--20 MeV) cascade and fission neutrons in the active medium. Both compensation mechanisms are important to help balance the response of a calorimeter to incident electrons and hadrons, that is, to achieve a ratio of pulse heights (e/h ∼ 1) which will lead to the best energy resolution. 17 refs., 4 figs., 2 tabs

  9. Incomplete and imperfect information for sales compensation

    Raluca Valeanu

    2010-12-01

    Full Text Available Sales force compensation represents the fix and / or variable payment by the company. To compensate agents based on the results, the company set a goal which is brought to their attention through the compensation plan. Applying the model of moral hazard, where the agent behavior cannot be verified, it cannot be specified in the contract what is the expected behavior of the agent. In order to make an offer to contract principal should know the effort that the agent will submit it to define the payment and the contract is determined optimally in trade between the two conflicting objectives of the two participants in the contract. Although agent behavior cannot be verified, the result of this behavior should be measurable at the end of the contract so that the employer may make the contract contingent on effort commission agent for sale of which is measured by the amount of earnings to the company.

  10. 'Compensation neurosis': a review of the literature.

    Weighill, V E

    1983-01-01

    This review examines the literature on psychological reactions, often referred to as 'compensation neurosis', which occur after an accident and which are thought to be produced or maintained by a compensation claim. Theories and research are examined. The area is complicated and research so far is limited in scope and design. Few accident cases involve compensation claims and the incidence of psychological difficulties across the whole range of cases is unknown. Researchers have considered a number of background factors--severity of injury, pre-existing neurotic traits, social class, sex and age--but there has been little investigation of attitudinal, family, social and employment factors or of progress of the condition and follow-up after settlement. The review identifies a major research need for more adequate screening and sampling of cases and for more systematic investigation of personal and family factors.

  11. Software compensation in Particle Flow reconstruction

    Lan Tran, Huong; Sefkow, Felix; Green, Steven; Marshall, John; Thomson, Mark; Simon, Frank

    2017-01-01

    The Particle Flow approach to calorimetry requires highly granular calorimeters and sophisticated software algorithms in order to reconstruct and identify individual particles in complex event topologies. The high spatial granularity, together with analog energy information, can be further exploited in software compensation. In this approach, the local energy density is used to discriminate electromagnetic and purely hadronic sub-showers within hadron showers in the detector to improve the energy resolution for single particles by correcting for the intrinsic non-compensation of the calorimeter system. This improvement in the single particle energy resolution also results in a better overall jet energy resolution by improving the energy measurement of identified neutral hadrons and improvements in the pattern recognition stage by a more accurate matching of calorimeter energies to tracker measurements. This paper describes the software compensation technique and its implementation in Particle Flow reconstruct...

  12. Institutional directors and board compensation: Spanish evidence

    Felix López-Iturriaga

    2015-07-01

    Full Text Available We address the influence of directors who represent institutional investors in three aspects of board compensation policies: level of compensation, composition, and performance sensitivity. We differentiate pressure-sensitive directors (i.e., with business links and pressure-resistant directors (i.e., without business links. Our results show that pressure-resistant directors decrease total board compensation and its fixed proportion, whereas they increase the variable proportion of total remuneration and the pay-for-performance sensitivity. By contrast, pressure-sensitive directors offer the opposite results. These findings are consistent with the view that institutional investors are not a homogeneous group and that pressure-resistant directors fulfill a more thorough monitoring role.

  13. Compensation: Will it provide a waste site?

    Pulsipher, A.G.

    1993-01-01

    Offering an attractive compensation package to persuade a community to voluntarily accept an otherwise undesirable facility may work in some cases, but it's not likely to work for high-level nuclear-waste disposal. The public perception of the risks involved and the public distrust of the institutions responsible for managing those risks are just too great. Much of the controversy stems from public perceptions that the site-selection process itself is unfair. Resentment builds when this occurs, and offers of compensation come to be labeled bribes or blood money. The driving force behind current nuclear-waste policy is intergenerational equity - the moral concept that the generation that produced the waste should dispose of it, permanently. Regardless of the moral appeal, doubts have been raised about the technical feasibility of this approach. Alternatives featuring intergenerational monetary compensation may better honor the commitment hor-ellipsis and reduce pressure to try to do what may be impossible

  14. Sensing charges of the Ciona intestinalis voltage-sensing phosphatase.

    Villalba-Galea, Carlos A; Frezza, Ludivine; Sandtner, Walter; Bezanilla, Francisco

    2013-11-01

    Voltage control over enzymatic activity in voltage-sensitive phosphatases (VSPs) is conferred by a voltage-sensing domain (VSD) located in the N terminus. These VSDs are constituted by four putative transmembrane segments (S1 to S4) resembling those found in voltage-gated ion channels. The putative fourth segment (S4) of the VSD contains positive residues that likely function as voltage-sensing elements. To study in detail how these residues sense the plasma membrane potential, we have focused on five arginines in the S4 segment of the Ciona intestinalis VSP (Ci-VSP). After implementing a histidine scan, here we show that four arginine-to-histidine mutants, namely R223H to R232H, mediate voltage-dependent proton translocation across the membrane, indicating that these residues transit through the hydrophobic core of Ci-VSP as a function of the membrane potential. These observations indicate that the charges carried by these residues are sensing charges. Furthermore, our results also show that the electrical field in VSPs is focused in a narrow hydrophobic region that separates the extracellular and intracellular space and constitutes the energy barrier for charge crossing.

  15. Weak hadronic currents in compensation theory

    Pappas, R.C.

    1975-01-01

    Working within the framework of a compensation theory of strong and weak interactions, it is shown that: (1) an axial vector baryon number current can be included in the weak current algebra if certain restrictions on the K-meson strong couplings are relaxed; (2) the theory does not permit the introduction of strange currents of the chiral form V + A; and (3) the assumption that the superweak currents of the theory cannot contain certain CP conserving terms can be justified on the basis of compensation requirements

  16. Skew quad compensation for SPEAR minibeta optics

    Wille, K.

    1984-06-01

    With the new minibeta insertion for SPEAR the betatron coupling and the perturbations of beam optics caused by the solenoid field of the MARK III detector can't be compensated by the simple coils used so far. Therefore another scheme with four skew quads arranged in two families has been chosen. Even though this scheme doesn't compensate the effect of the solenoid on the beam completely, the residual emittance coupling is much less than 1% which should be sufficient under all running conditions. The major advantage of this concept is its simplicity

  17. Convention on supplementary compensation for nuclear damage

    Chinese Nuclear Society, Beijing; U.S. Nuclear Energy Institute

    2000-01-01

    The Contracting parties recognize the importance of the measures provided in the Vienna Convention on Civil Liability for Nuclear Damage and the Paris Convention on Third party liability in the Field of Nuclear Energy as well as in national legislation on compensation for nuclear damage consistent with the principles of these conventions. The Contracting parties desire to establish a worldwide liability regime to supplement and enhance these measures with a view to increasing the amount of compensation for nuclear damage and encourage regional and global co-operation to promote a higher level of nuclear safety in accordance with the principle of international partnership and solidarity

  18. Static compensators (STATCOMs) in power systems

    Shahnia, Farhad; Ghosh, Arindam

    2014-01-01

    A static compensator (STATCOM), also known as static synchronous compensator, is a member of the flexible alternating current transmission system (FACTS) devices. It is a power-electronics based regulating device which is composed of a voltage source converter (VSC) and is shunt-connected to alternating current electricity transmission and distribution networks. The voltage source is created from a DC capacitor and the STATCOM can exchange reactive power with the network. It can also supply some active power to the network, if a DC source of power is connected across the capacitor. A STATCOM

  19. Phase alteration compensation in reflection digital holography

    Rincon, O; Amezquita, R; Monroy, F

    2011-01-01

    The phase maps obtained from digital holographic microscopy techniques carry information about the axial lengths of the object under study. Additionally, these phase maps have information of tilt and curvatures with origin in the off-axis geometry and the magnification lenses system, respectively. Only a complete compensation of these extra phases allows a correct interpretation of the phase information. In this article a numerical strategy to compensate for these alterations is designed, using a phase mask located in different planes. This strategy is applied in the measurement of a phase steps plate using a digital holography setup.

  20. Security careers skills, compensation, and career paths

    Walker, Stephen W

    2014-01-01

    The third edition of Security Careers is the authoritative reference for current job descriptions and pay practices of security, compliance, ethics, environmental, health and safety occupations. The job descriptions and compensation ranges in this report are drawn from research from the Foushée Group, which has been conducting this research since 1980. Security Careers includes more than 75 job descriptions for security-related positions, which range from the entry-level security guard to the top global corporate executive. It also provides four years of compensation trend data to give a th

  1. Kayenta advanced series compensation operational experience

    1994-01-01

    The world's first three-phase, thyristor-controlled series compensation scheme with continuously variable impedance has been introduced into a transmission system. Energized and dedicated in September 1992, the installation was placed into commercial operation in January 1993 and has provided over one year of operating experience. This paper describes the 230 kV, 330 MVAr (60 Hz) advanced series compensation (ASC) project, located in north-eastern Arizona at Kayenta Substation on the 320 km Glen Canyon-Shiprock transmission line. The paper describes operating experiences, coordination with phase shifting transformer, phase shifter failure, platform power, system disturbances, and future plans.

  2. Radiation damage effects on calorimeter compensation

    Gabriel, T.A.; Handler, T.

    1990-01-01

    An important consideration in the design of a detector that is to be used at the Superconducting Super Collider (SSC) is the response of the calorimeter to electromagnetic and hadronic particles and the equality of those responses for different types of particles at equal incident energies, i.e. compensation. However, as the simulations that are reported show, the compensation characteristics of a calorimeter can be seriously compromised over a relatively short period of time due to the large radiation levels that are expected in the SSC environment. 6 refs., 3 figs

  3. Compensation systems for low temperature applications

    Skoczen, Balzej T

    2004-01-01

    The book is dedicated to the behaviour of ductile materials at cryogenic temperatures, structural stability issues and reliability oriented parametric optimisation of compensation systems containing the corrugated bellows. The problems of local and global stability of systems containing bellows, coupling between the low-cycle fatigue and stability as well as evolution of plastic strain fields, micro-damage and strain induced phase transformation in the corrugated shells at cryogenic temperatures are presented. As a special feature reliability oriented optimum design of compensation systems under strength, stability, fatigue and geometrical constraints is discussed. The relevant applications in the particle accelerators and cryogenic transfer lines are shown.

  4. The marriage premium and compensating wage differentials.

    Reed, W R; Harford, K

    1989-12-01

    This paper proposes and tests an alternative explanation of the marriage premium that relies upon differences in workers' tastes and compensating wage differentials. A key assumption is that marital status proxies for the consumption of family goods, such as children, and that these are costly. Workers whose greater demands for family goods are taste- generated and shown to choose jobs that offer greater wage, and less non-pecuniary compensation. This creates an observed wage premium that has nothing to do with differences in workers' productivities. Supporting empirical evidence for this hypothesis is presented, including a reevaluation of previous studies.

  5. Lossless Compression of Video using Motion Compensation

    Martins, Bo; Forchhammer, Søren

    1998-01-01

    We investigate lossless coding of video using predictive coding andmotion compensation. The methods incorporate state-of-the-art lossless techniques such ascontext based prediction and bias cancellation, Golomb coding, high resolution motion field estimation,3d-dimensional predictors, prediction...... using one or multiple previous images, predictor dependent error modelling, and selection of motion field by code length. For slow pan or slow zoom sequences, coding methods that use multiple previous images are up to 20% better than motion compensation using a single previous image and up to 40% better...

  6. Digital, electromagnetic rod position indicator with compensation

    Feilchenfeld, M.M.; Geis, C.G.

    1985-01-01

    A digital rod position indicator having discrete coils L 0 , L 1 , L 2 ..... spaced along the travel path of an elongate magnetically permeable member stores in digital form compensation signals for automatically adjusting the location relative to the coils at which a digital output signal representative of the position of the end of the elongate member transitions from one code to the next. The appropriate compensation signal is addressed using the digital output signal and a correction factor which takes into account the direction of movement including reversals. Reference is made to the positioning of the control rods in a pressurized water reactor. (author)

  7. Filament stretching rheometer: inertia compensation revisited

    Szabo, Peter; McKinley, Gareth H.

    2003-01-01

    The necessary inertia compensation used in the force balance for the filament stretching rheometer is derived for an arbitrary frame of reference. This enables the force balance to be used to extract correctly the extensional viscosity from measurements of the tensile force at either end of the e......The necessary inertia compensation used in the force balance for the filament stretching rheometer is derived for an arbitrary frame of reference. This enables the force balance to be used to extract correctly the extensional viscosity from measurements of the tensile force at either end...

  8. Coastal remote sensing – towards integrated coastal research and management

    Lück-Vogel, Melanie

    2012-10-01

    Full Text Available coastal resources and anthropogenic infrastructure for a safer future. What is the role of remote sensing? The coastal zone connects terrestrial biophysical systems with marine systems. Some marine ecosystems cannot function without intact inland... for the development of sound integrated management solutions. To date, however, remote sensing applications usually focus on areas landward from the highwater line (?terrestrial? remote sensing), while ?marine? remote sensing does not pay attention to the shallow...

  9. Tango, senses and sensuality

    María de los Angeles Montes

    2014-11-01

    Full Text Available One of the most important contributions of the Peircean paradigm to semiotics consists in its opening the sign to development and modification. Sense, meaning, is no longer a static and fixed property. The Peircean paradigm allows us to wonder about how signs are interpreted, how they make sense in actual reception practices. The purpose of this paper is to address the problem of the relationship between appropriation practices (Montes, 2011 and significance processes from the analysis of an empirical case, observing how signs of sensuality are produced in the ballroom tango dance. Tango has earned international reputation mainly as a sensuality dance thanks to its spectacularization and subsequent mediatization. However, as I expect to demonstrate, at the moment of reception, people put those discourses in interaction with specific appropriation practices that shape very special interpretive habits. I will address the issue from an empirical investigation, especially focused on the production of interpretants (emotional, energetic, and logical, that is to say, looking back to the sign reception from the body to the mind. From a corpus of 25 focused interviews with people who got to know tango through mass media but that afterwards learnt to dance it as a social dance, it is my intention to show what sensuality means to them today, and how that current practice interacts with other external and previous discourses to produce interpretive habits. Finally, I wish to offer a theoretical reflection about the relationship between these three types of interpretants, their interaction with the discourse of the mass media and the place corporality has in the reception processes.

  10. Adaptive friction compensation: a globally stable approach

    Verbert, K.A.; Tóth, R.; Babuska, R.

    2016-01-01

    In this paper, an adaptive friction compensation scheme is proposed. The friction force is computed as a timevarying friction coefficient multiplied by the sign of the velocity and an on-line update law is designed to estimate this coefficient based on the actual position and velocity errors.

  11. 33 CFR 136.235 - Compensation allowable.

    2010-07-01

    ... allowable. The amount of compensation allowable is limited to the actual net reduction or loss of earnings or profits suffered. Calculations for net reductions or losses must clearly reflect adjustments for... available; (d) Any saved overhead or normal expenses not incurred as a result of the incident; and (e) State...

  12. On the compensation effect in heterogeneous catalysis

    Pedersen, Thomas Bligaard; Honkala, Johanna Karoliina; Logadottir, Ashildur

    2003-01-01

    For a class of heterogeneously catalyzed reactions, we explain the compensation effect in terms of a switching of kinetic regimes leading to a concomitant change in the apparent activation energy and in the prefactor for the overall rate of the reaction. We first use the ammonia synthesis...

  13. Annual compensation for pipelines in Alberta

    2008-11-01

    The Surface Rights Board (SRB) in Alberta held a hearing in November 2007 to address three issues involving a pipeline for Enbridge Pipelines (Athabasca) Inc. as well as several land owner issues in Townships 66-68 and Ranges 17-19, all west of the 4th Meridian. The issues the SRB examined were the appropriate amount (i.e. magnitude) of compensation payable under right of entry orders under consideration; the appropriate structure of the compensation award; and to whom the compensation was payable. This document presented a review by the Farmer's Advocate Office (FAO) of the published decision of the SRB. The verbatim decision and rationale used by the SRB to award annual compensation for loss and/or ongoing nuisance and inconvenience was presented. The document could be useful to landowners as they determine their negotiation strategy when faced with considering future pipeline access agreements. The document included a discussion of the context for the decision and a case review. Specific topics that were covered included the rationale for the decision; long term effects of pipeline arguments and SRB commentary; the award and determination; and what still needs to be done. It was concluded that the SRB requires evidence in order to answer several questions regarding the magnitude of any losses, and to what degree, if any, had the nuisance, inconvenience, and loss of rights already been anticipated and factored into the operator's final offer

  14. 7 CFR 1280.208 - Compensation.

    2010-01-01

    ... 7 Agriculture 10 2010-01-01 2010-01-01 false Compensation. 1280.208 Section 1280.208 Agriculture Regulations of the Department of Agriculture (Continued) AGRICULTURAL MARKETING SERVICE (MARKETING AGREEMENTS... INFORMATION ORDER Lamb Promotion, Research, and Information Order Lamb Promotion, Research, and Information...

  15. Evaluation of the implementation of Employees Compensation ...

    Since the passage into law of the Employees Compensation Act in 2011, countless cases of workplace accidents have occurred in Nigeria. Yet there seems to be no succour for the Nigerian worker as many state governments have either refused to register with or do not have the will power to implement the legislation in ...

  16. Employing Conjoint Analysis in Making Compensation Decisions.

    Kienast, Philip; And Others

    1983-01-01

    Describes a method employing conjoint analysis that generates utility/cost ratios for various elements of the compensation package. Its superiority to simple preference surveys is examined. Results of a study of the use of this method in fringe benefit planning in a large financial institution are reported. (Author/JAC)

  17. Executive Compensation and the Cost of Debt

    Kabir, Mohammed Rezaul; Li, Hao; Veld-Merkoulova, Yulia V.

    2010-01-01

    We examine how executive compensation affects the cost of debt financing. Analyzing CEO pay data from the UK, we find that debt-like and equity-like pay components have opposite effects on the cost of debt. An increase in defined benefit pensions is associated with lower bond yield spread, while an

  18. ARCC Teacher Compensation Initiative: Literature Review

    Appalachia Regional Comprehensive Center, 2014

    2014-01-01

    In February 2014, the Tennessee State Board of Education (SBE) requested that the Appalachia Regional Comprehensive Center (ARCC) provide assistance to the SBE's Basic Education Program (BEP) Review Committee. The SBE requested additional information on the use and effectiveness of market-based teacher compensation and market-based incentives by…

  19. Open Business Models: New Compensation Mechanisms for ...

    Open Business Models: New Compensation Mechanisms for Creativity and Inclusion ... This research aims to explore important new business models in the networked society ... Linking research to urban planning at the ICLEI World Congress 2018 ... In partnership with UNESCO's Organization for Women in Science for the ...

  20. Inertia compensated force and pressure sensors

    Bill, B.; Engeler, P.; Gossweiler, C. [Kistler Instrumente AG, Winterthur (Switzerland)

    2001-07-01

    Any moving structure is affected by inertial effects. In case of force and pressure sensors, inertial effects cause measurement errors. The paper deals with novel signal conditioning methods and mechanical design features to minimize inertial effects. A novel solution for passive compensation of pressure sensors is presented. (orig.)

  1. Compensation of coupling in the SSC complex

    Pilat, F.; Bourianoff, G.

    1991-10-01

    This paper will describe a study of the coupling effects and their compensation by means of local depending techniques for some of the accelerators in the SSC Complex. Results concerning corrections and decoupling for the Low Energy and Medium Energy Boosters will be compared to results obtained for the Collider Ring. Some preliminary experimental data about measurement of coupling quantities will also be presented

  2. 44 CFR 295.21 - Allowable compensation.

    2010-10-01

    ... 44 Emergency Management and Assistance 1 2010-10-01 2010-10-01 false Allowable compensation. 295.21 Section 295.21 Emergency Management and Assistance FEDERAL EMERGENCY MANAGEMENT AGENCY, DEPARTMENT... no-cost crisis counseling services available in the community. FEMA will not reimburse for treatment...

  3. Executive Compensation and the Cost of Debt

    Kabir, Rezaul; Liu, Hao; Veld-Merkoulova, Yulia V.

    2013-01-01

    This study examines how different components of executive compensation affect the cost of debt. We find that debt-like and equity-like pay components have differing effects: an increase in defined benefit pensions is associated with lower bond yield spread, while higher share holdings lead to higher

  4. The Compensation Act 2006 and School Trips

    Hunter-Jones, John

    2006-01-01

    The Compensation Act 2006 received its Royal Assent on 25 July 2006. The Act allows the courts to have regard to the social utility of "desirable activities", including school trips, in considering negligence claims. The article reviews the law of negligence as it affects teachers of the very young and considers the possible impact of…

  5. 22 CFR 96.34 - Compensation.

    2010-04-01

    ... actually rendered, taking into account the country in which the adoption services are provided and norms... norms are known to the accrediting entity; the location, number, and qualifications of staff; workload requirements; budget; and size of the agency or person. (e) Any other compensation paid to the agency's or...

  6. Flywheels Would Compensate for Rotor Imbalance

    Hrastar, J. A. S.

    1982-01-01

    Spinning flywheels within rotor can null imbalance forces in rotor. Flywheels axes are perpendicular to each other and to rotor axis. Feedback signals from accelerometers or strain gages in platform control flywheel speeds and rotation directions. Concept should be useful for compensating rotating bodies on Earth. For example, may be applied to large industrial centrifuge, particularly if balance changes during operation.

  7. Paraxial charge compensator for electron cryomicroscopy

    Berriman, John A.; Rosenthal, Peter B.

    2012-01-01

    We describe a multi-hole condenser aperture for the production of several electron beams in the transmission electron microscope (TEM) making it possible to simultaneously image and irradiate spatially separated regions of a specimen. When the specimen is a thin film of vitreous ice suspended over a holey carbon film, simultaneous irradiation of the adjacent carbon support with the off-axis beam compensates for some of the effects of charging in the image formed by a beam irradiating only the ice. Because the intervening region is not irradiated, charge-neutralization of frozen-hydrated specimens can occur by a through-space mechanism such as the emission of secondary electrons from a grounded carbon support film. We use paraxial charge compensation (PCC) to control the amount of charge build-up on the specimen and observe the effects of charge on images. The multi-hole aperture thus provides a tool for investigating the mechanism of charging and charge mitigation during the imaging of radiation sensitive biological specimens by cryomicroscopy. -- Highlights: ► A multi-hole condenser aperture produces multiple (paraxial) beams in TEM. ► Paraxial charge compensation is used to study electron-optical effects of charging. ► Emission of secondary electrons controls charging by a through space mechanism. ► Paraxial beams compensate for charging effects in frozen-hydrated specimens.

  8. Feedback loop compensates for rectifier nonlinearity

    1966-01-01

    Signal processing circuit with two negative feedback loops rectifies two sinusoidal signals which are 180 degrees out of phase and produces a single full-wave rectified output signal. Each feedback loop incorporates a feedback rectifier to compensate for the nonlinearity of the circuit.

  9. Compensation Services Advisor | IDRC - International Development ...

    Job Summary The Compensation Services Advisor is accountable for the effective ... Coordinates the annual Performance Review and Assessment System ... by IDRC and the broader financial and social implications of working in Canada. ... in areas such as mortgages, credit and so on to individuals not accustomed to ...

  10. Wavefront compensation applied to AVLIS laser systems

    Gonsiorowski, T.; Wirth, A.

    1995-01-01

    The efficiency of an AVLIS system depends upon the power density and uniformity of the laser system. Because of wavefront aberrations the realized beam quality is not ideal. Wavefront compensation provides a means to improve beam quality and system efficiency. (author)

  11. Software compensation in particle flow reconstruction

    Tran, Huong Lan; Krueger, Katja; Sefkow, Felix [Deutsches Elektronen-Synchrotron (DESY), Hamburg (Germany); Green, Steven; Marshall, John; Thomson, Mark [Cavendish Laboratory, Cambridge (United Kingdom); Simon, Frank [Max-Planck-Institut fuer Physik, Muenchen (Germany)

    2017-10-15

    The particle flow approach to calorimetry benefits from highly granular calorimeters and sophisticated software algorithms in order to reconstruct and identify individual particles in complex event topologies. The high spatial granularity, together with analogue energy information, can be further exploited in software compensation. In this approach, the local energy density is used to discriminate electromagnetic and purely hadronic sub-showers within hadron showers in the detector to improve the energy resolution for single particles by correcting for the intrinsic non-compensation of the calorimeter system. This improvement in the single particle energy resolution also results in a better overall jet energy resolution by improving the energy measurement of identified neutral hadrons and improvements in the pattern recognition stage by a more accurate matching of calorimeter energies to tracker measurements. This paper describes the software compensation technique and its implementation in particle flow reconstruction with the Pandora Particle Flow Algorithm (PandoraPFA). The impact of software compensation on the choice of optimal transverse granularity for the analogue hadronic calorimeter option of the International Large Detector (ILD) concept is also discussed.

  12. Software compensation in particle flow reconstruction

    Tran, Huong Lan; Krueger, Katja; Sefkow, Felix [Deutsches Elektronen-Synchrotron DESY, Hamburg (Germany); Green, Steven; Marshall, John; Thomson, Mark [Cavendish Laboratory, Cambridge (United Kingdom); Simon, Frank [Max-Planck-Institut fuer Physik, Muenchen (Germany)

    2017-10-15

    The particle flow approach to calorimetry benefits from highly granular calorimeters and sophisticated software algorithms in order to reconstruct and identify individual particles in complex event topologies. The high spatial granularity, together with analogue energy information, can be further exploited in software compensation. In this approach, the local energy density is used to discriminate electromagnetic and purely hadronic sub-showers within hadron showers in the detector to improve the energy resolution for single particles by correcting for the intrinsic non-compensation of the calorimeter system. This improvement in the single particle energy resolution also results in a better overall jet energy resolution by improving the energy measurement of identified neutral hadrons and improvements in the pattern recognition stage by a more accurate matching of calorimeter energies to tracker measurements. This paper describes the software compensation technique and its implementation in particle flow reconstruction with the Pandora Particle Flow Algorithm (PandoraPFA). The impact of software compensation on the choice of optimal transverse granularity for the analogue hadronic calorimeter option of the International Large Detector (ILD) concept is also discussed. (orig.)

  13. Software compensation in particle flow reconstruction

    Tran, Huong Lan; Krueger, Katja; Sefkow, Felix; Green, Steven; Marshall, John; Thomson, Mark; Simon, Frank

    2017-10-01

    The particle flow approach to calorimetry benefits from highly granular calorimeters and sophisticated software algorithms in order to reconstruct and identify individual particles in complex event topologies. The high spatial granularity, together with analogue energy information, can be further exploited in software compensation. In this approach, the local energy density is used to discriminate electromagnetic and purely hadronic sub-showers within hadron showers in the detector to improve the energy resolution for single particles by correcting for the intrinsic non-compensation of the calorimeter system. This improvement in the single particle energy resolution also results in a better overall jet energy resolution by improving the energy measurement of identified neutral hadrons and improvements in the pattern recognition stage by a more accurate matching of calorimeter energies to tracker measurements. This paper describes the software compensation technique and its implementation in particle flow reconstruction with the Pandora Particle Flow Algorithm (PandoraPFA). The impact of software compensation on the choice of optimal transverse granularity for the analogue hadronic calorimeter option of the International Large Detector (ILD) concept is also discussed.

  14. 31 CFR 28.515 - Compensation.

    2010-07-01

    ... 31 Money and Finance: Treasury 1 2010-07-01 2010-07-01 false Compensation. 28.515 Section 28.515 Money and Finance: Treasury Office of the Secretary of the Treasury NONDISCRIMINATION ON THE BASIS OF... a rate less than that paid to employees of the opposite sex for equal work on jobs the performance...

  15. Wire compensation: Performance, SPS MDs, pulsed system

    Dorda, U

    2008-01-01

    A wire compensation (BBLR) scheme has been proposed in order to improve the long range beam-beam performance of the nominal LHC and its phase 1 and phase 2 upgrades[1]. In this paper we present experimental experience of the CERN SPS wires (BBLR) and report on progress with the RF BBLR.

  16. Compensation techniques for operational amplifier bias current

    Silva, M.S.

    1981-01-01

    Two techniques are proposed for the compensation of the input current on operational amplifiers that can be used on inverting and non-inverting configurations. A qualitative analysis of temperature drift problems is made, and as a practical application, the construction of a voltage follower for high impedance measurements is presented. (Author) [pt

  17. Paraxial charge compensator for electron cryomicroscopy

    Berriman, John A. [Division of Physical Biochemistry, MRC National Institute for Medical Research, The Ridgeway, Mill Hill, London, NW7 1AA (United Kingdom); Rosenthal, Peter B., E-mail: peter.rosenthal@nimr.mrc.ac.uk [Division of Physical Biochemistry, MRC National Institute for Medical Research, The Ridgeway, Mill Hill, London, NW7 1AA (United Kingdom)

    2012-05-15

    We describe a multi-hole condenser aperture for the production of several electron beams in the transmission electron microscope (TEM) making it possible to simultaneously image and irradiate spatially separated regions of a specimen. When the specimen is a thin film of vitreous ice suspended over a holey carbon film, simultaneous irradiation of the adjacent carbon support with the off-axis beam compensates for some of the effects of charging in the image formed by a beam irradiating only the ice. Because the intervening region is not irradiated, charge-neutralization of frozen-hydrated specimens can occur by a through-space mechanism such as the emission of secondary electrons from a grounded carbon support film. We use paraxial charge compensation (PCC) to control the amount of charge build-up on the specimen and observe the effects of charge on images. The multi-hole aperture thus provides a tool for investigating the mechanism of charging and charge mitigation during the imaging of radiation sensitive biological specimens by cryomicroscopy. -- Highlights: Black-Right-Pointing-Pointer A multi-hole condenser aperture produces multiple (paraxial) beams in TEM. Black-Right-Pointing-Pointer Paraxial charge compensation is used to study electron-optical effects of charging. Black-Right-Pointing-Pointer Emission of secondary electrons controls charging by a through space mechanism. Black-Right-Pointing-Pointer Paraxial beams compensate for charging effects in frozen-hydrated specimens.

  18. 7 CFR 301.74-5 - Compensation.

    2010-01-01

    ... exclusively at farmers markets or similar outlets that require orchard owners to sell only fruit that they... of commercial stone fruit orchards. Owners of commercial stone fruit orchards are eligible to receive... marketers. Orchard owners eligible for compensation under this paragraph who market all fruit they produce...

  19. Women's Experience in the Workers' Compensation System.

    Guthrie, Robert; Jansz, Janis

    2006-09-01

    Gender differences is a question of major importance within workers' compensation given the increased role of women in the workforce over the past several decades. This article reviews literature relating to women's experiences following work injury. An Australian study is used as background to exploring the broad issue of the question of gender equity in workers' compensation. In doing so it takes account of historical, legal and medical issues. Women's experience in the workers' compensation system is different to that of men due to a range of factors. It is heavily influenced by the industrial environment in which they work. Women are paid less than men in many instances and work in gender-segregated circumstances, which often reduces their industrial bargaining power. Women also suffer different forms of injury and disease to men because of the different nature of their work. The Australian experience suggests that as a consequence of the combination of lesser industrial bargaining power, lower wages and differing forms of injury and disease women often receive less than men in compensation payments, struggle to obtain equity in the dispute resolution process and experience greater difficulties in returning to work following injury or disease.

  20. 1979-1980 Administrative Compensation Survey.

    Bryan, James; And Others

    Results of the 1979-80 Administrative Compensation Survey Report conducted by the College and University Personnel Association are presented. The survey is based on 1,383 responses and covers 77 positions. Salary data are indicated for the median and interquartile range for each position. Data are provided by type of institution, by size of…

  1. 1981-1982 Administrative Compensation Survey.

    Miller, Jan P.; And Others

    Results of the College and University Personnel Association's 1981-1982 Administrative Compensation Survey, which provides data on 94 positions, is presented. Questionnaires were sent to 2,770 higher education institutions, and 1,391 usable responses were obtained. Salary data indicate the median and the interquartile range for each position and…

  2. Administrative Compensation Survey, 1983-84.

    Benedict, Forest C.; And Others

    Results of the College and University Personnel Association's 1983-1984 Administrative Compensation Survey, which provides data on 99 positions, is presented. Questionnaires were sent to 2,856 higher education institutions, and 1,515 usable responses were obtained. Salary data indicate the median and the interquartile range for each position and…

  3. 77 FR 5381 - Plum Pox Compensation

    2012-02-03

    ... orchards, including direct marketers, and fruit tree nurseries. Compensation payments are provided to... stone fruit growers and direct marketers and in fruit tree nurseries, along with the effects of... economic losses experienced by grove owners, direct marketers, and nursery owners who are subject to an EAN...

  4. Attitudes toward the dubious compensation claim.

    LEGGO, C

    1951-07-01

    Laws providing for compensation of workmen for occupational injury are a powerful socio-economic force. In settlement of compensation claims the goal, difficult to achieve, is fairness to employee, employer and insurance carrier. Often, medical, legal, economic and social considerations conflict with one another. A "fact" in one field may not be considered so in another. Since medical data and testimony often guide the ultimate decision of a compensation claim, the physician's attitude is a large factor not only immediately and directly in determination of the case at hand but, perhaps more important, in the ultimate direction of the socio-economic forces which spring from the sum of all such determinations. To perpetuate the good in workmen's compensation laws, the next generation of physicians-and of lawyers and business administrators as well, for they, too, are involved-ought to have basic training in the social sciences in order that they may have a broad rather than a segmental view of the problems with which they deal.

  5. Hybrid VAR compensator with improved efficiency

    V. V. Burlaka

    2015-03-01

    Full Text Available In modern electrical networks thyristor-switched capacitors (TSC are most used devices for VAR compensation. These devices don’t contain rotating parts and mechanical contacts, provide a stepwise control of reactive power and no generation of harmonics to the network. However, with the help of TSC it’s not possible to ensure smooth control of reactive power and capacitor banks (CB are exposed to the negative impact of higher harmonic components of the network voltage. Hybrid VAR compensator don’t have such drawbacks. It consists of active filter (AF and capacitor bank with discrete regulation. The main drawback of such systems is the necessity of accessing all six terminals of CB, while most of them are manufactured with three terminals, internally delta-connected. In the article, the topology and control system of hybrid VAR compensator free from beforementioned drawback, is proposed. The control system provides operating modes of overcompensation or undercompensation reactive power. VAR distribution regulator performs redistribution of reactive power between active filter and capacitor banks with the condition to minimize active filter’s power. Scheme of the hybrid VAR compensator, which includes a three-phase three-terminal delta-connected capacitor banks, is shown. Proposed approach allows to provide smooth control of reactive power, isolate the capacitor bank from harmonic currents and use a more effective low-voltage power components

  6. Robotic motion compensation for applications in radiation oncology

    Herrmann, Christian

    2013-01-01

    Radiation therapy today, on account of improvements in treatment procedures over the last 60 years, allows precise treatment of static tumors inside the human body. However, irradiation of moving tumors is still a challenging task as moving tumors often leave the treatment beam and the radiation dose delivered to the tumor reduces simultaneously increasing that on healthy tissue. This research work aims to push the frontiers of radiation therapy in order to enable precise treatment of moving tumors with focus on research and development of a unique real-time system enabling active motion compensation through robotic means to compensate tumor motion. During treatment, patients lie on a treatment couch which is normally used for static position corrections of patient set-up errors prior to radiation treatment. The treatment couch used, called HexaPOD, is a parallel manipulator with six degrees of freedom which can precisely position heavy loads inside a small region. Despite the HexaPOD not initially built with dynamics in mind, it is used in this work for sustained motion compensation by moving patients such that tumors stay precisely located at the center of the treatment beam during the complete course of treatment. In order to realize real-time tumor motion compensation by means of the HexaPOD, several challenges need to be addressed. Real-time aspects are covered by the adoption of a hard real-time operation system in combination with measurement and estimation of latencies of all physical quantities in the compensation system such as tumor or breathing position measurements. Accurate timing information is respected consistently in the whole system and all software-induced latencies are adaptively compensated for. This requires knowledge of future tumor positions from predictors. Several predictors for breathing and tumor motion predictions are proposed and evaluated in terms of a variety of different performance metrics. Extensions to prediction algorithms are

  7. Robotic motion compensation for applications in radiation oncology

    Herrmann, Christian

    2013-07-22

    Radiation therapy today, on account of improvements in treatment procedures over the last 60 years, allows precise treatment of static tumors inside the human body. However, irradiation of moving tumors is still a challenging task as moving tumors often leave the treatment beam and the radiation dose delivered to the tumor reduces simultaneously increasing that on healthy tissue. This research work aims to push the frontiers of radiation therapy in order to enable precise treatment of moving tumors with focus on research and development of a unique real-time system enabling active motion compensation through robotic means to compensate tumor motion. During treatment, patients lie on a treatment couch which is normally used for static position corrections of patient set-up errors prior to radiation treatment. The treatment couch used, called HexaPOD, is a parallel manipulator with six degrees of freedom which can precisely position heavy loads inside a small region. Despite the HexaPOD not initially built with dynamics in mind, it is used in this work for sustained motion compensation by moving patients such that tumors stay precisely located at the center of the treatment beam during the complete course of treatment. In order to realize real-time tumor motion compensation by means of the HexaPOD, several challenges need to be addressed. Real-time aspects are covered by the adoption of a hard real-time operation system in combination with measurement and estimation of latencies of all physical quantities in the compensation system such as tumor or breathing position measurements. Accurate timing information is respected consistently in the whole system and all software-induced latencies are adaptively compensated for. This requires knowledge of future tumor positions from predictors. Several predictors for breathing and tumor motion predictions are proposed and evaluated in terms of a variety of different performance metrics. Extensions to prediction algorithms are

  8. Stuck in the middle: The emotional labours of case managers in the personal injury compensation system.

    Newnam, Sharon; Petersen, Alan; Keleher, Helen; Collie, Alex; Vogel, Adam; McClure, Rod

    2016-10-17

    Case managers within injury compensation systems are confronted with various emotional demands. Employing the concept of emotional labour, this paper explores distinctive aspects of these demands. The findings are drawn from focus groups with 21 Australian case managers. Case managers work was characterised by extra-role commitments, emotional control, stress and balancing tensions arising from differing stakeholder expectations about outcomes related to compensation and return to work. By examining the experiences of case managers, the findings add to the literature on the emotional labour of front line service workers, especially with respect to the demands involved in managing the conflicting demands of work.

  9. A point focusing double parabolic trough concentrator

    Murphree, Quincy C. [Kentucky Mountain Bible College, Vancleve, KY (United States)

    2001-07-01

    This article shows that a point focusing solar concentrator can be made from two reflective parabolic troughs, a primary and a secondary, by orienting their longitudinal axes in perpendicular directions and separating them by the difference of their focal lengths along the optical axis. This offers a new alternative to the conventional 3-D paraboloidal concentrator permitting more flexibility in designs for applications requiring high concentrations. Both advantages and disadvantages are discussed. The intensity concentration ratio distribution is calculated in the focal plane and has elliptically shaped contours due to the inherent compensation of errant rays by the concave secondary. The ratio of the major to minor axes was 2.61 for the case considered, resulting in a concentration {approx}2.61 times that of a comparable concentrator without the compensation afforded by a concave secondary. Still, geometrical constraints limit the concentration to about 2000 suns for mirror quality errors of 5 mr. Optimisation of the compensation effect holds potential for improved performance for other concentrator designs. Finally, the functional dependence of the peak concentration and shading factor upon design parameters are presented. (Author)

  10. Superstrong Adjustable Permanent Magnet for a Linear Collider Final Focus

    Iwashita, Y

    2004-01-01

    Super-strong permanent magnets are being considered as one of the candidates for the final focus quadrupole magnets in a linear collider. A short prototype with temperature compensation included and variable strength capability has been designed and fabricated. Fabrication details and some magnetic measurement results will be presented.

  11. Ambition is nothing without focus : Compensating for negative transfer of experience in R&D

    Ghosh, A.; Martin, Xavier; Pennings, J.M.; Wezel, F.C.

    2014-01-01

    Organizations create high-impact inventions when they combine disparate strands of technology in their corporate research and development. We theorize that when undertaking complex inventive search characterized by high breadth, i.e., drawing on multiple diverse technology components, an

  12. Depth-of-Interaction Compensation Using a Focused-Cut Scintillator for a Pinhole Gamma Camera

    Alhassen, Fares; Kudrolli, Haris; Singh, Bipin; Kim, Sangtaek; Seo, Youngho; Gould, Robert G.; Nagarkar, Vivek V.

    2011-01-01

    Preclinical SPECT offers a powerful means to understand the molecular pathways of drug interactions in animal models by discovering and testing new pharmaceuticals and therapies for potential clinical applications. A combination of high spatial resolution and sensitivity are required in order to map radiotracer uptake within small animals. Pinhole collimators have been investigated, as they offer high resolution by means of image magnification. One of the limitations of pinhole geometries is ...

  13. Fecundity compensation and tolerance to a sterilizing pathogen in Daphnia.

    Vale, P F; Little, T J

    2012-09-01

    Hosts are armed with several lines of defence in the battle against parasites: they may prevent the establishment of infection, reduce parasite growth once infected or persevere through mechanisms that reduce the damage caused by infection, called tolerance. Studies on tolerance in animals have focused on mortality, and sterility tolerance has not been investigated experimentally. Here, we tested for genetic variation in the multiple steps of defence when the invertebrate Daphnia magna is infected with the sterilizing bacterial pathogen Pasteuria ramosa: anti-infection resistance, anti-growth resistance and the ability to tolerate sterilization once infected. When exposed to nine doses of a genetically diverse pathogen inoculum, six host genotypes varied in their average susceptibility to infection and in their parasite loads once infected. How host fecundity changed with increasing parasite loads did not vary between genotypes, indicating that there was no genetic variation for this measure of fecundity tolerance. However, genotypes differed in their level of fecundity compensation under infection, and we discuss how, by increasing host fitness without targeting parasite densities, fecundity compensation is consistent with the functional definition of tolerance. Such infection-induced life-history shifts are not traditionally considered to be part of the immune response, but may crucially reduce harm (in terms of fitness loss) caused by disease, and are a distinct source of selection on pathogens. © 2012 The Authors. Journal of Evolutionary Biology © 2012 European Society For Evolutionary Biology.

  14. Phase compensated gas turbine governor for damping oscillatory modes

    Yee, S.K. [Siemens Transmission and Distribution Limited, Manchester (United Kingdom); Milanovic, J.V. [School of Electrical and Electronic Engineering, University of Manchester, PO Box 88, Manchester M60 1 QD (United Kingdom); Hughes, F.M. [Manchester (United Kingdom)

    2009-08-15

    With market deregulation, there is constant pressure to utilise existing assets in more effective ways in order to achieve high levels of performance and as governor technologies mature the ability of governors to achieve much more than the standard power-frequency regulation function increases. Thus, this paper has focused on a more active use of governor control for a gas turbine to provide improved system stabilisation and performance via the inclusion of phase compensation in the governor control loop. Due to the decoupled nature of the mechanical power and excitation control loops, performance improvement via governor control does not interfere with generator voltage regulation, which is a drawback of conventional generator damping provision via a power system stabiliser (PSS). In addition, the mechanical power control loop is also less affected by the operating condition of the power system and is hence more robust. It is shown that inclusion of appropriate phase compensation in the governor control loop can improve dynamic and transient stability, either alone or in conjunction with a PSS in the exciter control loop, without adversely interfering with voltage control or changing steady state power-frequency regulation. (author)

  15. Compensation and Production in Family Medicine by Practice Ownership

    Alison C. Essary

    2016-02-01

    Full Text Available The increasing focus on high performance, patient-centered, team-based care calls for a strategy to evaluate cost-effective primary care. The trend toward physician practice consolidation further challenges the primary care health care system. Productivity measures establish provider value and help inform decision making regarding resource allocation in this evolving health care system. In this national survey of family medicine practices, physician assistant (PA productivity, as defined by mean annual patient encounters, exceeds that of both nurse practitioners (NPs and physicians in physician-owned practices and of NPs in hospital or integrated delivery system-owned practices. Total compensation, defined as salary, bonus, incentives, and honoraria for physicians, is significantly more compared to both PAs and NPs, regardless of practice ownership or productivity. Physician assistants and NPs earn equivalent compensation, regardless of practice ownership or productivity. Not only do these data support the value and role of PAs and NPs on the primary care team but also highlight differences in patient encounters between practice settings. Rural and underserved community practices, where physician-owned practices persist, also merit further consideration. Further research is needed to inform both organizational and policy decisions for the provision of high-quality, cost-effective, and accessible primary health care.

  16. Deformation compensation in dynamic tomography; Compensation de deformations en tomographie dynamique

    Desbat, L. [Universite Joseph Fourier, UMR CNRS 5525, 38 - Grenoble (France); Roux, S. [Universite Joseph Fourier, TIMC-IMAG, In3S, Faculte de Medecine, 38 - Grenoble (France)]|[CEA Grenoble, Lab. d' Electronique et de Technologie de l' Informatique (LETI), 38 (France); Grangeat, P. [CEA Grenoble, Lab. d' Electronique et de Technologie de l' Informatique (LETI), 38 (France)

    2005-07-01

    This work is a contribution to the compensation of motion in tomography. New classes of deformation are proposed, that compensates analytically by an algorithm of a F.B.P. type reconstruction. This work makes a generalisation of the known results for affine deformations, in parallel geometry and fan-beam, to deformation classes of infinite dimension able to include strong non linearities. (N.C.)

  17. Re-Planning for Compensator-Based IMRT with Original Compensators

    Zhang, Geoffrey; Feygelman, Vladimir; Stevens, Craig; Li Weiqi; Leuthold, Susan; Springett, Gregory; Hoffe, Sarah

    2011-01-01

    Compared with multileaf collimator (MLC)-based intensity-modulated radiotherapy (IMRT) for moving targets, compensator-based IMRT has advantages such as shorter beam-on time, fewer monitor units with potentially decreased secondary carcinogenesis risk, better optimization-to-deliverable dose conversion, and often better dose conformity. Some of the disadvantages include additional time for the compensators to be built and delivered, as well as extra cost. Patients undergoing treatment of abdominal cancers often experience weight loss. It would be necessary to account for this change in weight with a new plan and a second set of compensators. However, this would result in treatment delays and added costs. We have developed a method to re-plan the patient using the same set of compensators. Because the weight changes seen with the treatment of abdominal cancers are usually relatively small, a new 4D computed tomography (CT) acquired in the treatment position with markers on the original isocenter tattoos can be registered to the original planning scan. The contours of target volumes from the original scans are copied to the new scan after fusion. The original compensator set can be used together with a few field-in-field (FiF) beams defined by the MLC (or beams with cerrobend blocks for accelerators not equipped with a MLC). The weights of the beams with compensators are reduced so that the FiF or blocked beams can be optimized to mirror the original plan and dose distribution. Seven abdominal cancer cases are presented using this technique. The new plan on the new planning CT images usually has the same dosimetric quality as the original. The target coverage and dose uniformity are improved compared with the plan without FiF/block modification. Techniques combining additional FiF or blocked beams with the original compensators optimize the treatment plans when patients lose weight and save time and cost compared with generating plans with a new set of compensators.

  18. Global patterns and trends in human-wildlife conflict compensation.

    Ravenelle, Jeremy; Nyhus, Philip J

    2017-12-01

    Human-wildlife conflict is a major conservation challenge, and compensation for wildlife damage is a widely used economic tool to mitigate this conflict. The effectiveness of this management tool is widely debated. The relative importance of factors associated with compensation success is unclear, and little is known about global geographic or taxonomic differences in the application of compensation programs. We reviewed research on wildlife-damage compensation to determine geographic and taxonomic gaps, analyze patterns of positive and negative comments related to compensation, and assess the relative magnitude of global compensation payments. We analyzed 288 publications referencing wildlife compensation and identified 138 unique compensation programs. These publications reported US$222 million (adjusted for inflation) spent on compensation in 50 countries since 1980. Europeans published the most articles, and compensation funding was highest in Europe, where depredation by wolves and bears was the most frequently compensated damage. Authors of the publications we reviewed made twice as many negative comments as positive comments about compensation. Three-quarters of the negative comments related to program administration. Conversely, three-quarters of the positive comments related to program outcomes. The 3 most common suggestions to improve compensation programs included requiring claimants to employ damage-prevention practices, such as improving livestock husbandry or fencing of crops to receive compensation (n = 25, 15%); modifying ex post compensation schemes to some form of outcome-based performance payment (n = 21, 12%); and altering programs to make compensation payments more quickly (n = 14, 8%). We suggest that further understanding of the strengths and weaknesses of compensation as a conflict-mitigation tool will require more systematic evaluation of the factors driving these opinions and that differentiating process and outcomes and understanding

  19. A novel method of temperature compensation for piezoresistive microcantilever-based sensors.

    Han, Jianqiang; Wang, Xiaofei; Yan, Tianhong; Li, Yan; Song, Meixuan

    2012-03-01

    Microcantilever with integrated piezoresistor has been applied to in situ surface stress measurement in the field of biochemical sensors. It is well known that piezoresistive cantilever-based sensors are sensitive to ambient temperature changing due to highly temperature-dependent piezoresistive effect and mismatch in thermal expansion of composite materials. This paper proposes a novel method of temperature drift compensation for microcantilever-based sensors with a piezoresistive full Wheatstone bridge integrated at the clamped ends by subtracting the amplified output voltage of the reference cantilever from the output voltage of the sensing cantilever through a simple temperature compensating circuit. Experiments show that the temperature drift of microcantilever sensors can be significantly reduced by the method.

  20. A novel input-parasitic compensation technique for a nanopore-based CMOS DNA detection sensor

    Kim, Jungsuk

    2016-12-01

    This paper presents a novel input-parasitic compensation (IPC) technique for a nanopore-based complementary metal-oxide-semiconductor (CMOS) DNA detection sensor. A resistive-feedback transimpedance amplifier is typically adopted as the headstage of a DNA detection sensor to amplify the minute ionic currents generated from a nanopore and convert them to a readable voltage range for digitization. But, parasitic capacitances arising from the headstage input and the nanopore often cause headstage saturation during nanopore sensing, thereby resulting in significant DNA data loss. To compensate for the unwanted saturation, in this work, we propose an area-efficient and automated IPC technique, customized for a low-noise DNA detection sensor, fabricated using a 0.35- μm CMOS process; we demonstrated this prototype in a benchtop test using an α-hemolysin ( α-HL) protein nanopore.

  1. Mobile Sensing Systems

    Macias, Elsa; Suarez, Alvaro; Lloret, Jaime

    2013-01-01

    Rich-sensor smart phones have made possible the recent birth of the mobile sensing research area as part of ubiquitous sensing which integrates other areas such as wireless sensor networks and web sensing. There are several types of mobile sensing: individual, participatory, opportunistic, crowd, social, etc. The object of sensing can be people-centered or environment-centered. The sensing domain can be home, urban, vehicular… Currently there are barriers that limit the social acceptance of mobile sensing systems. Examples of social barriers are privacy concerns, restrictive laws in some countries and the absence of economic incentives that might encourage people to participate in a sensing campaign. Several technical barriers are phone energy savings and the variety of sensors and software for their management. Some existing surveys partially tackle the topic of mobile sensing systems. Published papers theoretically or partially solve the above barriers. We complete the above surveys with new works, review the barriers of mobile sensing systems and propose some ideas for efficiently implementing sensing, fusion, learning, security, privacy and energy saving for any type of mobile sensing system, and propose several realistic research challenges. The main objective is to reduce the learning curve in mobile sensing systems where the complexity is very high. PMID:24351637

  2. Mobile sensing systems.

    Macias, Elsa; Suarez, Alvaro; Lloret, Jaime

    2013-12-16

    Rich-sensor smart phones have made possible the recent birth of the mobile sensing research area as part of ubiquitous sensing which integrates other areas such as wireless sensor networks and web sensing. There are several types of mobile sensing: individual, participatory, opportunistic, crowd, social, etc. The object of sensing can be people-centered or environment-centered. The sensing domain can be home, urban, vehicular… Currently there are barriers that limit the social acceptance of mobile sensing systems. Examples of social barriers are privacy concerns, restrictive laws in some countries and the absence of economic incentives that might encourage people to participate in a sensing campaign. Several technical barriers are phone energy savings and the variety of sensors and software for their management. Some existing surveys partially tackle the topic of mobile sensing systems. Published papers theoretically or partially solve the above barriers. We complete the above surveys with new works, review the barriers of mobile sensing systems and propose some ideas for efficiently implementing sensing, fusion, learning, security, privacy and energy saving for any type of mobile sensing system, and propose several realistic research challenges. The main objective is to reduce the learning curve in mobile sensing systems where the complexity is very high.

  3. Mobile Sensing Systems

    Elsa Macias

    2013-12-01

    Full Text Available Rich-sensor smart phones have made possible the recent birth of the mobile sensing research area as part of ubiquitous sensing which integrates other areas such as wireless sensor networks and web sensing. There are several types of mobile sensing: individual, participatory, opportunistic, crowd, social, etc. The object of sensing can be people-centered or environment-centered. The sensing domain can be home, urban, vehicular… Currently there are barriers that limit the social acceptance of mobile sensing systems. Examples of social barriers are privacy concerns, restrictive laws in some countries and the absence of economic incentives that might encourage people to participate in a sensing campaign. Several technical barriers are phone energy savings and the variety of sensors and software for their management. Some existing surveys partially tackle the topic of mobile sensing systems. Published papers theoretically or partially solve the above barriers. We complete the above surveys with new works, review the barriers of mobile sensing systems and propose some ideas for efficiently implementing sensing, fusion, learning, security, privacy and energy saving for any type of mobile sensing system, and propose several realistic research challenges. The main objective is to reduce the learning curve in mobile sensing systems where the complexity is very high.

  4. Theoretical description and design of nanomaterial slab waveguides: application to compensation of optical diffraction.

    Kivijärvi, Ville; Nyman, Markus; Shevchenko, Andriy; Kaivola, Matti

    2018-04-02

    Planar optical waveguides made of designable spatially dispersive nanomaterials can offer new capabilities for nanophotonic components. As an example, a thin slab waveguide can be designed to compensate for optical diffraction and provide divergence-free propagation for strongly focused optical beams. Optical signals in such waveguides can be transferred in narrow channels formed by the light itself. We introduce here a theoretical method for characterization and design of nanostructured waveguides taking into account their inherent spatial dispersion and anisotropy. Using the method, we design a diffraction-compensating slab waveguide that contains only a single layer of silver nanorods. The waveguide shows low propagation loss and broadband diffraction compensation, potentially allowing transfer of optical information at a THz rate.

  5. Online Sensor Drift Compensation for E-Nose Systems Using Domain Adaptation and Extreme Learning Machine

    Luo, Guangchun; Qin, Ke; Wang, Nan; Niu, Weina

    2018-01-01

    Sensor drift is a common issue in E-Nose systems and various drift compensation methods have received fruitful results in recent years. Although the accuracy for recognizing diverse gases under drift conditions has been largely enhanced, few of these methods considered online processing scenarios. In this paper, we focus on building online drift compensation model by transforming two domain adaptation based methods into their online learning versions, which allow the recognition models to adapt to the changes of sensor responses in a time-efficient manner without losing the high accuracy. Experimental results using three different settings confirm that the proposed methods save large processing time when compared with their offline versions, and outperform other drift compensation methods in recognition accuracy. PMID:29494543

  6. Online Sensor Drift Compensation for E-Nose Systems Using Domain Adaptation and Extreme Learning Machine

    Zhiyuan Ma

    2018-03-01

    Full Text Available Sensor drift is a common issue in E-Nose systems and various drift compensation methods have received fruitful results in recent years. Although the accuracy for recognizing diverse gases under drift conditions has been largely enhanced, few of these methods considered online processing scenarios. In this paper, we focus on building online drift compensation model by transforming two domain adaptation based methods into their online learning versions, which allow the recognition models to adapt to the changes of sensor responses in a time-efficient manner without losing the high accuracy. Experimental results using three different settings confirm that the proposed methods save large processing time when compared with their offline versions, and outperform other drift compensation methods in recognition accuracy.

  7. The Nature of Whiplash in a Compensable Environment: Injury, Disability, Rehabilitation, and Compensation Systems.

    Connelly, Luke B

    2017-07-01

    Synopsis Whiplash is a compensable injury in many jurisdictions, but there is considerable heterogeneity in the compensation arrangements that apply across jurisdictions, even within some countries. These compensation schemes have, however, been subject to a common set of interrelated concerns, chiefly concerning the incentives, behaviors, and outcomes that may arise when financial compensation for injuries is available to injured parties. This article provides a nontechnical overview of some of those concerns through the lens of economics: principally, insurance economics and health economics, including related subsets such as information economics and agency theory, as well as economics and the law. It notes that because it is generally infeasible to randomize the treatment (ie, compensation) via trials, analyses of observational data are necessary to discover more about the relationship between compensation and health outcomes. This poses the analytical challenge of discovering causal connections between phenomena from nonrandomized data sets. The present article calls for further research that would enable convincing causal interpretations of such relationships via the careful analysis of rich observational data sets using modern econometric methods. J Orthop Sports Phys Ther 2017;47(7):503-508. Epub 16 Jun 2017. doi:10.2519/jospt.2017.7533.

  8. Nano-bio-sensing

    Carrara, Sandro

    2011-01-01

    This book examines state-of-the-art applications of nano-bio-sensing. It brings together researchers from nano-electronics and bio-technology, providing multidisciplinary content from nano-structures fabrication to bio-sensing applications.

  9. A Novel Temperature Compensation Method for a MEMS Gyroscope Oriented on a Periphery Circuit

    Huiliang Cao

    2013-09-01

    Full Text Available This paper investigates temperature compensation methods used for the scale factor and bias of the MEMS gyroscope within the temperature range from − 40°C to 60°C. The structure and periphery monitor circuit are introduced. Then the determinant elements of the MEMS gyroscope's scale factor are analysed and the results indicate that scale factor is directly proportional to drive amplitude and sense loop gain and is inversely proportional to the frequency gap between two modes. After that, the compensation methods are proposed, the thermal resistor's positive temperature coefficient (tempco is utilized to calibrate the scale factor's tempco through regulating the drive mode amplitude and the sense loop gain, and each method is applied respectively and the results are contrasted. The test results of the two specimens express that the most effective compensation method could decrease the scale factor's tempco from 693ppm/°C (640ppm/°C to 250ppm/°C (257ppm/°C, improving it by 63.9% (59.8%. Finally, a method of declining bias's tempco is investigated and implemented after scale factor compensation. A summator with a thermal resistor is utilized at the output level and decreases the bias's tempco from 103.89°/h/°C (100.78°/h/°C to 9.70°/h/°C (12°/h/°C improving it by 90.7% (88%. Repeat tests are performed based on two specimens to prove the repeatability and reproducibility of the methods.

  10. US-LHC IR magnet error analysis and compensation

    Wei, J.; Ptitsin, V.; Pilat, F.; Tepikian, S.; Gelfand, N.; Wan, W.; Holt, J.

    1998-01-01

    This paper studies the impact of the insertion-region (IR) magnet field errors on LHC collision performance. Compensation schemes including magnet orientation optimization, body-end compensation, tuning shims, and local nonlinear correction are shown to be highly effective

  11. MTB-USDH Compensation Tracking System (MTB-CTS)

    US Agency for International Development — MTB-USDH Compensation Tracking System: is the USDH Compensation Tracking System (MTB-CTS) to assist managers in monitoring their payroll costs for U.S. direct hires....

  12. The relationship between South African CEO compensation and ...

    1A study of corporate financial performance and CEO compensation by Firth, Lohne,. Ropstad .... requires both a qualitative and quantitative analysis. REMCOs, in ...... 'Executive compensation as an agency problem', Journal of. Economic ...

  13. A time averaged background compensator for Geiger-Mueller counters

    Bhattacharya, R.C.; Ghosh, P.K.

    1983-01-01

    The GM tube compensator described stores background counts to cancel an equal number of pulses from the measuring channel providing time averaged compensation. The method suits portable instruments. (orig.)

  14. Socioeconomic outcomes following spinal cord injury and the role of no-fault compensation: longitudinal study.

    Paul, C; Derrett, S; McAllister, S; Herbison, P; Beaver, C; Sullivan, M

    2013-12-01

    Longitudinal cohort study. To estimate socioeconomic and work outcomes over 2 and a half years following spinal cord injury (SCI), and to compare those in receipt of compensation (Accident Compensation Corporation, ACC) and those not. People admitted to the two spinal units in 2007-2009 in New Zealand, where there is a unique no-fault compensation scheme for injury. Interviews were conducted at ∼6, 18 and 30 months after SCI and data collected on pre-SCI and post-SCI health and socioeconomic characteristics. Poisson regression, quantile regression and a linear mixed model regression were used to compare differences in outcomes. Of the 162 eligible people, 118 (73%) participated and 91(77%) were followed to 30 months; 79% received ACC. Median personal income, self-reported standard of living and household income adequacy all fell slightly to 18 months and then stabilized at 30 months. At that time, 49% had returned to paid work. Among those not eligible for ACC, income fell to less than half the ACC group (Pretained their economic status and that return to work was relatively high appear to be due to the proportion entitled to the ACC no-fault compensation scheme for injury; with earnings-related compensation, a focus on rehabilitation to work and non-means-tested support services. This situation should mitigate against the downward spiral into poverty and further ill-health.

  15. Introduction to remote sensing

    Cracknell, Arthur P

    2007-01-01

    Addressing the need for updated information in remote sensing, Introduction to Remote Sensing, Second Edition provides a full and authoritative introduction for scientists who need to know the scope, potential, and limitations in the field. The authors discuss the physical principles of common remote sensing systems and examine the processing, interpretation, and applications of data. This new edition features updated and expanded material, including greater coverage of applications from across earth, environmental, atmospheric, and oceanographic sciences. Illustrated with remotely sensed colo

  16. Word Domain Disambiguation via Word Sense Disambiguation

    Sanfilippo, Antonio P.; Tratz, Stephen C.; Gregory, Michelle L.

    2006-06-04

    Word subject domains have been widely used to improve the perform-ance of word sense disambiguation al-gorithms. However, comparatively little effort has been devoted so far to the disambiguation of word subject do-mains. The few existing approaches have focused on the development of al-gorithms specific to word domain dis-ambiguation. In this paper we explore an alternative approach where word domain disambiguation is achieved via word sense disambiguation. Our study shows that this approach yields very strong results, suggesting that word domain disambiguation can be ad-dressed in terms of word sense disam-biguation with no need for special purpose algorithms.

  17. Preface: Remote Sensing in Coastal Environments

    Deepak R. Mishra

    2016-08-01

    Full Text Available The Special Issue (SI on “Remote Sensing in Coastal Environments” presents a wide range of articles focusing on a variety of remote sensing models and techniques to address coastal issues and processes ranging for wetlands and water quality to coral reefs and kelp habitats. The SI is comprised of twenty-one papers, covering a broad range of research topics that employ remote sensing imagery, models, and techniques to monitor water quality, vegetation, habitat suitability, and geomorphology in the coastal zone. This preface provides a brief summary of each article published in the SI.

  18. Sales compensation governance: the last frontier of corporate reform.

    Gundy, Peter R; Gaeta, Elizabeth C

    2004-01-01

    The area of sales compensation has remained relatively untouched by recent pressures for compensation reform. This article highlights some of the ways that sales organizations stumble in managing their compensation programs, and why it takes more than a simple tactical fix to address these problems effectively. The authors describe a more structured governance framework that not only identifies and resolves key sales compensation issues, but ultimately safeguards the effectiveness and financial integrity of the sales organization itself.

  19. Zero energy buildings and mismatch compensation factors

    Lund, Henrik; Marszal, Anna Joanna; Heiselberg, Per

    2011-01-01

    This paper takes an overall energy system approach to analysing the mismatch problem of zero energy and zero emission buildings (ZEBs). The mismatch arises from hourly differences in energy production and consumption at the building level and results in the need for exchange of electricity via...... the public grid even though the building has an annual net-exchange of zero. This paper argues that, when looked upon from the viewpoint of the overall electricity supply system, a mismatch can be both negative and positive. Moreover, there are often both an element of levelling out mismatches between...... of the energy production unit. Based on historical data for the electricity supply area in western Denmark, this paper makes a first attempt to quantify mismatch compensation factors. The results indicate that such compensation factors are a little below one for buildings with photovoltaics (PV) and a little...

  20. Adaptive Engine Torque Compensation with Driveline Model

    Park Jinrak

    2018-01-01

    Full Text Available Engine net torque is the total torque generated by the engine side, and includes the fuel combustion torque, the friction torque, and additionally the starter motor torque in case of hybrid vehicles. The engine net torque is utilized to control powertrain items such as the engine itself, the transmission clutch, also the engine clutch, and it must be accurate for the precise powertrain control. However, this net torque can vary with the engine operating conditions like the engine wear, the changes of the atmospheric pressure and the friction torque. Thus, this paper proposes the adaptive engine net torque compensator using driveline model which can cope with the net torque change according to engine operating conditions. The adaptive compensator was applied on the parallel hybrid vehicle and investigated via MATLAB Simcape Driveline simulation.

  1. Chromaticity compensation scheme for the Main Injector

    Bogacz, S.A.

    1993-05-01

    The current Main Injector lattice is studied in the context of full chromaticity compensation in the presence of the eddy current, saturation and the end-pack sextupole fields generated by the dipole magnets. Two families of correcting sextupole magnets are placed to compensate these fields and to adjust the chromaticity (in both planes) to some desired value. Variation of the dipole induced sextupole fields with the B-field (changing along a ramp) are modeled according to recent experimental measurements of the Main Injector dipole magnet Analysis of the required sextupole strengths is carried out along two realistic momentum ramps. The results of our calculation give quantitative insight into the requisite performance of the sextupole magnets

  2. Percentage compensation arrangements: suspect, but not illegal.

    Fedor, F P

    2001-01-01

    Percentage compensation arrangements, in which a service is outsourced to a contractor that is paid in accordance with the level of its performance, are widely used in many business sectors. The HHS Office of Inspector General (OIG) has shown concern that these arrangements in the healthcare industry may offer incentives for the performance of unnecessary services or cause false claims to be made to Federal healthcare programs in violation of the antikickback statute and the False Claims Act. Percentage compensation arrangements can work and need not run afoul of the law as long as the healthcare organization carefully oversees the arrangement and sets specific safeguards in place. These safeguards include screening contractors, carefully evaluating their compliance programs, and obligating them contractually to perform within the limits of the law.

  3. Compensating for telecommunication delays during robotic telerehabilitation.

    Consoni, Leonardo J; Siqueira, Adriano A G; Krebs, Hermano I

    2017-07-01

    Rehabilitation robotic systems may afford better care and telerehabilitation may extend the use and benefits of robotic therapy to the home. Data transmissions over distance are bound by intrinsic communication delays which can be significant enough to deem the activity unfeasible. Here we describe an approach that combines unilateral robotic telerehabilitation and serious games. This approach has a modular and distributed design that permits different types of robots to interact without substantial code changes. We demonstrate the approach through an online multiplayer game. Two users can remotely interact with each other with no force exchanges, while a smoothing and prediction algorithm compensates motions for the delay in the Internet connection. We demonstrate that this approach can successfully compensate for data transmission delays, even when testing between the United States and Brazil. This paper presents the initial experimental results, which highlight the performance degradation with increasing delays as well as improvements provided by the proposed algorithm, and discusses planned future developments.

  4. Phase Noise Compensation for OFDM Systems

    Leshem, Amir; Yemini, Michal

    2017-11-01

    We describe a low complexity method for time domain compensation of phase noise in OFDM systems. We extend existing methods in several respects. First we suggest using the Karhunen-Lo\\'{e}ve representation of the phase noise process to estimate the phase noise. We then derive an improved datadirected choice of basis elements for LS phase noise estimation and present its total least square counterpart problem. The proposed method helps overcome one of the major weaknesses of OFDM systems. We also generalize the time domain phase noise compensation to the multiuser MIMO context. Finally we present simulation results using both simulated and measured phased noise. We quantify the tracking performance in the presence of residual carrier offset.

  5. CGI delay compensation. [Computer Generated Image

    Mcfarland, R. E.

    1986-01-01

    Computer-generated graphics in real-time helicopter simulation produces objectionable scene-presentation time delays. In the flight simulation laboratory at Ames Research Center, it has been determined that these delays have an adverse influence on pilot performance during agressive tasks such as nap of the earth (NOE) maneuvers. Using contemporary equipment, computer generated image (CGI) time delays are an unavoidable consequence of the operations required for scene generation. However, providing that magnitude distortions at higher frequencies are tolerable, delay compensation is possible over a restricted frequency range. This range, assumed to have an upper limit of perhaps 10 or 15 rad/sec, conforms approximately to the bandwidth associated with helicopter handling qualities research. A compensation algorithm is introduced here and evaluated in terms of tradeoffs in frequency responses. The algorithm has a discrete basis and accommodates both a large, constant transport delay interval and a periodic delay interval, as associated with asynchronous operations.

  6. Design of a dynamic compensated temperature sensor

    Yan, Wu; Katz, E.M.; Kerlin, T.W.

    1991-01-01

    One important function of a temperature sensor in a nuclear power plant is to track changing process temperatures, but the sensor output lags the changing temperature. This lag may have a large influence when the sensor is used in control or safety systems. Therefore, it is advantageous to develop methods that increase the sensor response speed. The goal of this project is to develop a fast-responding temperature sensor, the dynamic compensated temperature sensor (DCTS), based on signal dynamic compensation technology. To verify the theoretical basis of the DCTS and incorporate the DCTS into a real temperature measurement process, several experiments have been performed. The DCTS is a simple approach that can decrease the temperature sensor's response time, and it can provide faster temperature signals to the nuclear power plant safety system

  7. Sense of moving

    Christensen, Mark Schram; Grünbaum, Thor

    2017-01-01

    In this chapter, we assume the existence of a sense of “movement activity” that arises when a person actively moves a body part. This sense is usually supposed to be part of sense of agency (SoA). The purpose of the chapter is to determine whether the already existing experimental paradigms can...

  8. The Use of Remotely Sensed Rainfall for Managing Drought Risk: A Case Study of Weather Index Insurance in Zambia

    Emily Black

    2016-04-01

    Full Text Available Remotely sensed rainfall is increasingly being used to manage climate-related risk in gauge sparse regions. Applications based on such data must make maximal use of the skill of the methodology in order to avoid doing harm by providing misleading information. This is especially challenging in regions, such as Africa, which lack gauge data for validation. In this study, we show how calibrated ensembles of equally likely rainfall can be used to infer uncertainty in remotely sensed rainfall estimates, and subsequently in assessment of drought. We illustrate the methodology through a case study of weather index insurance (WII in Zambia. Unlike traditional insurance, which compensates proven agricultural losses, WII pays out in the event that a weather index is breached. As remotely sensed rainfall is used to extend WII schemes to large numbers of farmers, it is crucial to ensure that the indices being insured are skillful representations of local environmental conditions. In our study we drive a land surface model with rainfall ensembles, in order to demonstrate how aggregation of rainfall estimates in space and time results in a clearer link with soil moisture, and hence a truer representation of agricultural drought. Although our study focuses on agricultural insurance, the methodological principles for application design are widely applicable in Africa and elsewhere.

  9. Glass scintillator pair for compensation neutron logging

    Ji Changsong; Li Xuezhi; Yiu Guangduo

    1985-01-01

    Glass scintillator pair types ST 1604 and ST 1605 for compensation of neutron logging is developed. The neutron sensitive material used is multistick lithium glass scintillators 3 and 4 mm in diameter respectively. Thermoneutron detection efficiencies are 50-60% and 100% respectively. The detection efficiency for 60 Co γ ray is lower than 0.3%. The type ST 1604 and ST 1605 may also be used as high sensitive neutron detectors in an intensive γ ray field

  10. Compensation for gravitational sag of bent mirror

    Mao, Chengwen; Jiang, Hui; He, Yan; Liang, Dongxu; Lan, Xuying; Yan, Shuai [Shanghai Synchrotron Radiation Facility, Shanghai Institute of Applied Physics, CAS, Shanghai 201800 (China); Shu, De-ming [Advanced Photon Source, Argonne National Laboratory, Argonne, IL 60439 (United States); Li, Aiguo, E-mail: aiguo.li@sinap.ac.cn [Shanghai Synchrotron Radiation Facility, Shanghai Institute of Applied Physics, CAS, Shanghai 201800 (China)

    2017-05-01

    The gravitational sag of aspheric bent mirrors with face-up or face-down geometry produces a nonnegligible optical error. As an effective compensation, width optimization is used to match the combined effects of the gravitational and bending moments. This method is described by analytical expressions and two calculation algorithms. The results of theoretical simulations and finite element analysis have proved that this method can reduce the slope error resulting from gravitational sag to the level of nano radians.

  11. Compensation for gravitational sag of bent mirror

    Mao, Chengwen; Jiang, Hui; He, Yan; Liang, Dongxu; Lan, Xuying; Yan, Shuai; Shu, De-ming; Li, Aiguo

    2017-01-01

    The gravitational sag of aspheric bent mirrors with face-up or face-down geometry produces a nonnegligible optical error. As an effective compensation, width optimization is used to match the combined effects of the gravitational and bending moments. This method is described by analytical expressions and two calculation algorithms. The results of theoretical simulations and finite element analysis have proved that this method can reduce the slope error resulting from gravitational sag to the level of nano radians.

  12. Review of beamloading and compensation in synchrotrons

    Koscielniak, S.

    2001-10-01

    This paper discusses the theory and state-of-the-art applications of beam loading and compensation in synchrotrons. In particular it discusses the developments in the introduction of Magnetic Alloy (e.g. Finemet) cores and adoption of low Q cavities; e plus-e minus factories with very large current (e.g. KEKB, PEP II) and developments at p,p factories (e.g. LHC) and simulation codes

  13. Lithium compensation of GaAs

    Alexiev, D.; Tavendale, A.J.

    1988-08-01

    Defects generated following Li diffusion into GaAs were studied by optical deep level transient spectroscopy (ODLTS) and deep level transient spectroscopy (DLTS). In an exploratory series of experiments, the effect of Li diffusion on existing trap spectra, defect generation and as a means for the compensation of GaAs was studied. The variables included diffusion temperature, initial trap spectra of GaAs and annealing periods. Detailed measurements of trap energies were made

  14. 45 CFR 302.65 - Withholding of unemployment compensation.

    2010-10-01

    ... 45 Public Welfare 2 2010-10-01 2010-10-01 false Withholding of unemployment compensation. 302.65... HUMAN SERVICES STATE PLAN REQUIREMENTS § 302.65 Withholding of unemployment compensation. The State plan... State agency charged with the administration of the State unemployment compensation laws in accordance...

  15. An EMTDC Model of a Three Level four MVAR Compensator

    Rasmussen, Tonny Wederberg

    1997-01-01

    The paper discusses the dynamic characteristics of a three level ±4mvar solid state var compensator which is built and will be used for dynamic reactive power compensation in a wind farm. An investigation has been carried out of the influence of the compensator reactor, the DC intermediate voltage...

  16. 26 CFR 31.3231(e)-1 - Compensation.

    2010-04-01

    .... (a) Definition—(1) The term compensation has the same meaning as the term wages in section 3121(a... regarding the inclusion of fringe benefits in compensation, see § 31.3121(a)-1T. (6) Split-dollar life... 26 Internal Revenue 15 2010-04-01 2010-04-01 false Compensation. 31.3231(e)-1 Section 31.3231(e)-1...

  17. 20 CFR 701.401 - Coverage under state compensation programs.

    2010-04-01

    ... 20 Employees' Benefits 3 2010-04-01 2010-04-01 false Coverage under state compensation programs...; DEFINITIONS AND USE OF TERMS Coverage Under State Compensation Programs § 701.401 Coverage under state compensation programs. (a) Exclusions from the definition of “employee” under § 701.301(a)(12), and the...

  18. 12 CFR 918.2 - Annual directors' compensation policy.

    2010-01-01

    ... § 918.3. At a minimum, such policy shall address the activities or functions for which attendance is... 12 Banks and Banking 7 2010-01-01 2010-01-01 false Annual directors' compensation policy. 918.2... HOME LOAN BANKS BANK DIRECTOR COMPENSATION AND EXPENSES § 918.2 Annual directors' compensation policy...

  19. 29 CFR 505.3 - Prevailing minimum compensation.

    2010-07-01

    ... 29 Labor 3 2010-07-01 2010-07-01 false Prevailing minimum compensation. 505.3 Section 505.3 Labor... HUMANITIES § 505.3 Prevailing minimum compensation. (a)(1) In the absence of an alternative determination...)(2) of this section, the prevailing minimum compensation required to be paid under the Act to the...

  20. 14 CFR 250.8 - Denied boarding compensation.

    2010-01-01

    ... 14 Aeronautics and Space 4 2010-01-01 2010-01-01 false Denied boarding compensation. 250.8 Section... PROCEEDINGS) ECONOMIC REGULATIONS OVERSALES § 250.8 Denied boarding compensation. (a) Every carrier shall tender to a passenger eligible for denied boarding compensation, on the day and place the denied boarding...

  1. 39 CFR 3.2 - Compensation of Board.

    2010-07-01

    ... 39 Postal Service 1 2010-07-01 2010-07-01 false Compensation of Board. 3.2 Section 3.2 Postal Service UNITED STATES POSTAL SERVICE THE BOARD OF GOVERNORS OF THE U.S. POSTAL SERVICE BOARD OF GOVERNORS (ARTICLE III) § 3.2 Compensation of Board. Section 202(a)(1) of title 39 provides for the compensation of...

  2. Assessment of Wetland Valuation Processes for Compensation in ...

    The issue of compensation has been debated in various fora; however compensation on wetland resources has not been given the primary place. Wetland valuation like any other type of valuation requires going through stages, which may be more complex than real estate valuation for compensation. This study therefore ...

  3. Critical Issues in Assessing Teacher Compensation. Backgrounder. No. 2638

    Richwine, Jason; Biggs, Andrew G.

    2012-01-01

    A November 2011 Heritage Foundation report--"Assessing the Compensation of Public-School Teachers"--presented data on teacher salaries and benefits in order to inform debates about teacher compensation reform. The report concluded that public-school teacher compensation is far ahead of what comparable private-sector workers enjoy, and that…

  4. 31 CFR 30.0 - Executive compensation and corporate governance.

    2010-07-01

    ... 31 Money and Finance: Treasury 1 2010-07-01 2010-07-01 false Executive compensation and corporate governance. 30.0 Section 30.0 Money and Finance: Treasury Office of the Secretary of the Treasury TARP STANDARDS FOR COMPENSATION AND CORPORATE GOVERNANCE § 30.0 Executive compensation and corporate governance...

  5. 20 CFR 10.15 - May compensation rights be waived?

    2010-04-01

    ... 20 Employees' Benefits 1 2010-04-01 2010-04-01 false May compensation rights be waived? 10.15 Section 10.15 Employees' Benefits OFFICE OF WORKERS' COMPENSATION PROGRAMS, DEPARTMENT OF LABOR FEDERAL... AMENDED General Provisions Rights and Penalties § 10.15 May compensation rights be waived? No employer or...

  6. 28 CFR 301.301 - Compensable and noncompensable injuries.

    2010-07-01

    ... only those injuries suffered during the performance of an inmate's regular work assignment. However... institution, when such work has been approved by staff, may also be compensable. (c) Compensation is not paid... in any activity not related to the actual performance of the work assignment are not compensable, and...

  7. 34 CFR 75.519 - Dual compensation of staff.

    2010-07-01

    ... 34 Education 1 2010-07-01 2010-07-01 false Dual compensation of staff. 75.519 Section 75.519... by a Grantee? Project Staff § 75.519 Dual compensation of staff. A grantee may not use its grantee to pay a project staff member for time or work for which that staff member is compensated from some other...

  8. 10 CFR 39.53 - Energy compensation source.

    2010-01-01

    ... 10 Energy 1 2010-01-01 2010-01-01 false Energy compensation source. 39.53 Section 39.53 Energy NUCLEAR REGULATORY COMMISSION LICENSES AND RADIATION SAFETY REQUIREMENTS FOR WELL LOGGING Equipment § 39.53 Energy compensation source. The licensee may use an energy compensation source (ECS) which is...

  9. Adaptive pseudolinear compensators of dynamic characteristics of automatic control systems

    Skorospeshkin, M. V.; Sukhodoev, M. S.; Timoshenko, E. A.; Lenskiy, F. V.

    2016-04-01

    Adaptive pseudolinear gain and phase compensators of dynamic characteristics of automatic control systems are suggested. The automatic control system performance with adaptive compensators has been explored. The efficiency of pseudolinear adaptive compensators in the automatic control systems with time-varying parameters has been demonstrated.

  10. 38 CFR 3.658 - Offsets; dependency and indemnity compensation.

    2010-07-01

    ... 38 Pensions, Bonuses, and Veterans' Relief 1 2010-07-01 2010-07-01 false Offsets; dependency and... AFFAIRS ADJUDICATION Pension, Compensation, and Dependency and Indemnity Compensation Adjustments and Resumptions § 3.658 Offsets; dependency and indemnity compensation. (a) When an award of dependency and...

  11. 38 CFR 3.461 - Dependency and indemnity compensation.

    2010-07-01

    ... 38 Pensions, Bonuses, and Veterans' Relief 1 2010-07-01 2010-07-01 false Dependency and indemnity... ADJUDICATION Pension, Compensation, and Dependency and Indemnity Compensation Apportionments § 3.461 Dependency...'s award of dependency and indemnity compensation will be apportioned where there is a child or...

  12. 38 CFR 3.702 - Dependency and indemnity compensation.

    2010-07-01

    ... 38 Pensions, Bonuses, and Veterans' Relief 1 2010-07-01 2010-07-01 false Dependency and indemnity... ADJUDICATION Pension, Compensation, and Dependency and Indemnity Compensation Concurrent Benefits and Elections § 3.702 Dependency and indemnity compensation. (a) Right to elect. A person who is eligible for death...

  13. Installation of the sag compensator for HANARO

    Kim, Hyungkyoo; Jung, Hoansung; Lim, Incheol; Ahn, Gukhoon

    2008-01-01

    Electric power is essential for all industrial plants and also for nuclear facilities. HANARO is a research reactor which produces a 30 MW thermal power. HANARO is designed to be tripped automatically when interruptions or some extent of sags occur. HANARO has the reactor regulation system(RRS) and reactor protection system(RPS). HANARO is designed so as to be tripped automatically by insertion of control absorber rods(CAR) and shut-off rods(SOR). When voltage sag or momentary interruption occurs, the reactor has an unwanted trip by insertion of CARs and SORs even though the process systems are still in operation. HANARO was experienced in a nuisance trip as often as the unexpected voltage sag and/or momentary interruption occurs. We installed the voltage sag compensator on the power supply for CARs and SORs so as to prevent an unwanted trip. We undertook voltage sag assessment of the AC coil contactor which is a component of the power supply unit for the SORs. The compensation time is determined to be less than 1 sec in consideration of the reactor safety. This paper is concerned with the impact of the momentary interruption on the reactor and the effect of the voltage sag compensator. (author)

  14. Optical compensation device for chest film radiography

    Gould, Robert G.; Hasegawa, Bruce H.; DeForest, Sherman E.; Schmidt, Gregory W.; Hier, Richard G.

    1990-07-01

    Although chest radiography is the most commonly performed radiographic examination and one of the most valuable and cost-effective studies in medicine it suffers from relatively high error rates in both missing pathology and false positive interpretations. Detectability of lung nodules and other structures in underpenetrated regions of the chest film can be improved by both exposure and optical compensation but current compensation systems require major capital cost or a significant change in normal clinical practice. A new optical compensation system called the " Intelligent X-Ray Illuminator" (IXI) automatically and virtually instantaneously generates a patient-specific optical unsharp mask that is projected directly on a radiograph. When a radiograph is placed on the IXI which looks much like a conventional viewbox it acquires a low-resolution electronic image of this film from which the film transmission is derived. The transmission information is inverted and blurred in an image processor to form an unsharp mask which is fed into a spatial light modulator (SLM) placed between a light source and the radiograph. The SLM tailors the viewbox luminance by decreasing illumination to underexposed (i. e. transmissive) areas of the radiograph presenting the observer with an optically unsharp-masked image. The IXI uses the original radiograph and will allow it to be viewed on demand with conventional (uniform illumination. Potentially the IXI could introduce the known beneficial aspects of optical unsharp masking into radiology at low capital

  15. Installation of the sag compensator for HANARO

    Kim, H. K.; Jung, H. S.; Ahn, G. H.; Lim, I. C.

    2008-01-01

    Electric power is essential for all industrial plants and also for nuclear facilities. HANARO is a research reactor which produces a 30MW thermal power. HANARO is designed to be tripped automatically when interruptions or some extents of sags occur. HANARO has the reactor regulation system (RRS) and reactor protection system (RPS). HANARO is designed so as to tripped automatically by insertion of control absorber rods (CAR) and shut-off rods (SOR). When voltage or momentary interruption occurs, the reactor has an unwanted trip by insertion of CARs and SORs even though the process systems are still in operation. HANARO was experienced in a nuisance trip as often as the unexpected voltage sag and/or momentary interruption occurs. We installed the voltage sag compensator on the power supply for CARs and SORs so as to prevent an unwanted trip. We undertook voltage sag assessment of the AC coil contactor which is a component of the power supply unit for the SORs. The compensation time is determined to be less than 1 sec in consideration of the reactor safety. This paper is concerned with the impact of the momentary interruption on the reactor and the effect of the voltage sag compensator

  16. Installation of the sag compensator for HANARO

    Kim, Hyung Kyoo; Jung, Hoan Sung; Lim, In Cheol; Ahn, Guk Hoon

    2008-01-01

    Electric power is essential for all industrial plants and also for nuclear facilities. HANARO is a research reactor which produces a 30MW thermal power. HANARO is designed to be tripped automatically when interruptions or some extent of sags occur. HANARO has the reactor regulation system(RRs) and reactor protection system(RPS). HANARO is designed so as to be tripped automatically by insertion of control absorber rods(CAR) and shut off rods(SOR). When voltage sag or momentary interruption occurs, the reactor has an unwanted trip by insertion of CARs and SORs even though the process systems are still in operation. HANARO was experienced in a nuisance trip as often as the unexpected voltage sag and/or momentary interruption occurs. We installed the voltage sag compensator voltage sag assessment of the AC coil contactor which is a component of the power supply unit for the SORs. The compensation time is determined to be less than 1 sec in consideration of the reactor safety. This paper is concerned with the impact of the momentary interruption on the reactor and the effect of the voltage sag compensator

  17. Direct Lorentz force compensation flowmeter for electrolytes

    Vasilyan, S., E-mail: suren.vasilyan@tu-ilmenau.de; Froehlich, Th. [Institute of Process Measurement and Sensor Technology, Ilmenau University of Technology, 98684 Ilmenau (Germany)

    2014-12-01

    A simplified method of contactless Lorentz force (LF) measurements for flow meters on electrolytes is described and realized. Modification and comparative representation are discussed against recently well-developed methods. Based on the catapult effect, that current carrying conductor experiences a repulsive force in a magnetic field, we demonstrate force measurement method of LF velocimetry applications by commonly known “electromagnetic force” compensation principle. Measurement approach through zero point stability is considered to minimize mechanical influences and avoid gravimetric uncertainties. Here, the current carrying wires are static fixed in the vicinity of magnet system at zero point stable position, while occurring deflection of magnets by electrolyte flow is compensated by external applied current within wires. Measurements performed by developed servo-system which drives control loop by means of optical position sensor for simplified (i) single wire and (ii) coil-like extended compensation schemes. Guided by experiments on electrolyte flow, we demonstrate the applicability of adopted principle for conductivities ranging from 2 to 20 S/m. Further improvements are discussed in agreement with the parameters of demonstration setup, straightforward theory, and experimental results. We argue that this method is potentially suitable for: (a) applications with higher conductivity like molten metal (order of 10{sup 6 }S/m) assuming spatial configuration of setup and (b) for lower range of conductivity (below 1 S/m) while this is strongly subject to stiffness of system and noise mainly mechanical and thermal radiations.

  18. ACCURACY DIMENSIONS IN REMOTE SENSING

    Á. Barsi

    2018-04-01

    Full Text Available The technological developments in remote sensing (RS during the past decade has contributed to a significant increase in the size of data user community. For this reason data quality issues in remote sensing face a significant increase in importance, particularly in the era of Big Earth data. Dozens of available sensors, hundreds of sophisticated data processing techniques, countless software tools assist the processing of RS data and contributes to a major increase in applications and users. In the past decades, scientific and technological community of spatial data environment were focusing on the evaluation of data quality elements computed for point, line, area geometry of vector and raster data. Stakeholders of data production commonly use standardised parameters to characterise the quality of their datasets. Yet their efforts to estimate the quality did not reach the general end-user community running heterogeneous applications who assume that their spatial data is error-free and best fitted to the specification standards. The non-specialist, general user group has very limited knowledge how spatial data meets their needs. These parameters forming the external quality dimensions implies that the same data system can be of different quality to different users. The large collection of the observed information is uncertain in a level that can decry the reliability of the applications. Based on prior paper of the authors (in cooperation within the Remote Sensing Data Quality working group of ISPRS, which established a taxonomy on the dimensions of data quality in GIS and remote sensing domains, this paper is aiming at focusing on measures of uncertainty in remote sensing data lifecycle, focusing on land cover mapping issues. In the paper we try to introduce how quality of the various combination of data and procedures can be summarized and how services fit the users’ needs. The present paper gives the theoretic overview of the issue, besides

  19. Accuracy Dimensions in Remote Sensing

    Barsi, Á.; Kugler, Zs.; László, I.; Szabó, Gy.; Abdulmutalib, H. M.

    2018-04-01

    The technological developments in remote sensing (RS) during the past decade has contributed to a significant increase in the size of data user community. For this reason data quality issues in remote sensing face a significant increase in importance, particularly in the era of Big Earth data. Dozens of available sensors, hundreds of sophisticated data processing techniques, countless software tools assist the processing of RS data and contributes to a major increase in applications and users. In the past decades, scientific and technological community of spatial data environment were focusing on the evaluation of data quality elements computed for point, line, area geometry of vector and raster data. Stakeholders of data production commonly use standardised parameters to characterise the quality of their datasets. Yet their efforts to estimate the quality did not reach the general end-user community running heterogeneous applications who assume that their spatial data is error-free and best fitted to the specification standards. The non-specialist, general user group has very limited knowledge how spatial data meets their needs. These parameters forming the external quality dimensions implies that the same data system can be of different quality to different users. The large collection of the observed information is uncertain in a level that can decry the reliability of the applications. Based on prior paper of the authors (in cooperation within the Remote Sensing Data Quality working group of ISPRS), which established a taxonomy on the dimensions of data quality in GIS and remote sensing domains, this paper is aiming at focusing on measures of uncertainty in remote sensing data lifecycle, focusing on land cover mapping issues. In the paper we try to introduce how quality of the various combination of data and procedures can be summarized and how services fit the users' needs. The present paper gives the theoretic overview of the issue, besides selected, practice

  20. Asbestos-related occupational cancers compensated under the Industrial Accident Compensation Insurance in Korea.

    Ahn, Yeon-Soon; Kang, Seong-Kyu

    2009-04-01

    Compensation for asbestos-related cancers occurring in occupationally-exposed workers is a global issue; this is also an issue in Korea. To provide basic information regarding compensation for workers exposed to asbestos, 60 cases of asbestos-related occupational lung cancer and mesothelioma that were compensated during 15 yr; from 1993 (the year the first case was compensated) to 2007 by the Korea Labor Welfare Corporation (KLWC) are described. The characteristics of the cases were analyzed using the KLWC electronic data and the epidemiologic investigation data conducted by the Occupational Safety and Health Research Institute (OSHRI) of the Korea Occupational Safety and Health Agency (KOSHA). The KLWC approved compensation for 41 cases of lung cancer and 19 cases of mesothelioma. Males accounted for 91.7% (55 cases) of the approved cases. The most common age group was 50-59 yr (45.0%). The mean duration of asbestos exposure for lung cancer and mesothelioma cases was 19.2 and 16.0 yr, respectively. The mean latency period for lung cancer and mesothelioma cases was 22.1 and 22.6 yr, respectively. The major industries associated with mesothelioma cases were shipbuilding and maintenance (4 cases) and manufacture of asbestos textiles (3 cases). The major industries associated with lung cancer cases were shipbuilding and maintenance (7 cases), construction (6 cases), and manufacture of basic metals (4 cases). The statistics pertaining to asbestos-related occupational cancers in Korea differ from other developed countries in that more cases of mesothelioma were compensated than lung cancer cases. Also, the mean latency period for disease onset was shorter than reported by existing epidemiologic studies; this discrepancy may be related to the short history of occupational asbestos use in Korea. Considering the current Korean use of asbestos, the number of compensated cases in Korea is expected to increase in the future but not as much as developed countries.

  1. Plasma focus breeder

    Ikuta, Kazunari.

    1981-09-01

    Instead of using linear accelerators, it is possible to breed fissile fuels with the help of high current plasma focus device. A mechanism of accelerating proton beam in plasma focus device to high energy would be a change of inductance in plasma column because of rapid growth of plasma instability. A possible scheme of plasma focus breeder is also proposed. (author)

  2. Entropy–enthalpy compensation as a fundamental concept and analysis tool for systematical experimental data

    Starikov, E.B.; Nordé n, B.

    2012-01-01

    Enthalpy-entropy compensation (EEC) has a definite physical sense. Here, we review EEC from a new standpoint, using the notion of correlation. The latter has two basic meanings: (a) 'A' is correlated to 'B' means 'A' results from 'B' or vice versa; (b) this same means there is some real, but hidden 'C' in connection to both 'A' and 'B'). In accordance with the interpretation (b), we try rationalizing EEC in terms of hidden, but physically real factors. © 2012 Elsevier B.V. All rights reserved.

  3. Experimental demonstration of H∞ filter performance for dynamic compensation of rhodium neutron detectors

    Park, Moon-Ghu; Choi, Yu-Sun; Lee, Kwang-Dae

    2008-01-01

    This paper describes the experimental demonstration of the theoretical result of the previous work on LMI (linear matrix inequality) based H ∞ filter for time-delay compensation of self-powered neutron detectors. The filter gains are optimized in the sense of noise attenuation level of H ∞ setting. By introducing bounded real lemma, the conventional algebraic Riccati inequalities are converted into linear matrix inequalities (LMIs). Finally, the filter design problem is solved via the convex optimization framework using LMIs. The experimental measurements of rhodium detector signal from a research reactor show that the predicted theoretical filter performance is verified by showing successful reconstruction of the reference power signal

  4. Improving LIGO calibration accuracy by tracking and compensating for slow temporal variations

    Tuyenbayev, D; Karki, S; Goetz, E; Izumi, K; Kissel, J S; Mendell, G; Savage, R L; Betzwieser, J; Kandhasamy, S; Cahillane, C; Weinstein, A J; Wade, M

    2017-01-01

    Calibration of the second-generation LIGO interferometric gravitational-wave detectors employs a method that uses injected periodic modulations to track and compensate for slow temporal variations in the differential length response of the instruments. These detectors utilize feedback control loops to maintain resonance conditions by suppressing differential arm length variations. We describe how the sensing and actuation functions of these servo loops are parameterized and how the slow variations in these parameters are quantified using the injected modulations. We report the results of applying this method to the LIGO detectors and show that it significantly reduces systematic errors in their calibrated outputs. (paper)

  5. A microcontroller-based compensated optical proximity detector employing the switching-mode synchronous detection technique

    Rakshit, Anjan; Chatterjee, Amitava

    2012-01-01

    This paper describes the development of a microcontroller-based optical proximity detector that can provide a low-cost yet powerful obstacle-sensing mechanism for mobile robots. The system is developed with the switching-mode synchronous detection technique to provide satisfactory performance over a wide range of operating conditions and is developed with the facility of externally setting a threshold, for reliable operation. The system is dynamically compensated against ambient illumination variations. Experimental studies demonstrate how the minimum distance of activation can be varied with different choices of thresholds. (paper)

  6. Entropy–enthalpy compensation as a fundamental concept and analysis tool for systematical experimental data

    Starikov, E.B.

    2012-06-01

    Enthalpy-entropy compensation (EEC) has a definite physical sense. Here, we review EEC from a new standpoint, using the notion of correlation. The latter has two basic meanings: (a) \\'A\\' is correlated to \\'B\\' means \\'A\\' results from \\'B\\' or vice versa; (b) this same means there is some real, but hidden \\'C\\' in connection to both \\'A\\' and \\'B\\'). In accordance with the interpretation (b), we try rationalizing EEC in terms of hidden, but physically real factors. © 2012 Elsevier B.V. All rights reserved.

  7. The Importance of Sensing Own's Movements in the World for the Sense of Personal Identity

    Mariana Broens

    2012-01-01

    Full Text Available Within philosophy and cognitive science, the focus in relation to the problem of personal identity has been almost exclusively on the brain. We submit that the resulting neglect of the body and of bodily movements in the world has been detrimental in understanding how organisms develop a sense of identity. We examine the importance of sensing one’s own movements for the development of a basic, nonconceptual sense of self. More specifically, we argue that the origin of the sense of self stems from the sensitivity to spontaneous movements. Based on this, the organism develops a sense of “I move” and, finally, a sense of “I can move”. Proprioception and kinesthesis are essential in this development. At the same time, we argue against the traditional dichotomy between so-called external and internal senses, agreeing with Gibson that perception of the self and of the environment invariably go together. We discuss a traditional distinction between two aspects of bodily self: the body sense and the body image. We suggest that they capture different aspects of the sense of self. We argue that especially the body sense is of great importance to our nonconceptual sense of self. Finally, we attempt to draw some consequences for research in cognitive science, specifically in the area of robotics, by examining a case of missing proprioception. We make a plea for robots to be equipped not just with external perceptual and motor abilities but also with a sense of proprioception. This, we submit, would constitute one further step towards understanding creatures acting in the world with a sense of themselves.

  8. Study of thick, nuclear-compensated silicon detectors; Etude des detecteurs epais au silicium compense nucleairement

    Le Coroller, Y. [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires

    1964-09-01

    A study is made here, from the point of view of the realization and the performance, of thick nuclear-compensated silicon detectors. After recalling the need for compensation and reviewing the existing methods, the author describes in detail the controlled realization of thick detectors by nuclear compensation from the theoretical and experimental points of view. The practical precautions which should be observed are given: control of the homogeneity of the starting material, control of the evolution of the compensation, elimination of parasitic processes. The performances of the detectors obtained are then studied: electrical characteristics (current, life-time) on the one hand, detection and spectrometry of penetrating radiations on the other hand. The results show, that the compensated diodes having an effective thickness of two millimeters operate satisfactorily as detectors for applied voltages of about 500 volts. The resolutions observed are then about 2 per cent for mono-energetic electrons and about 4 per cent for the gamma; they can be improved by the use of a pre-amplifier of very low background noise. (author) [French] Les detecteurs epais au silicium compense nucleairement sont etudies ici du double point de vue realisation et performances. Apres un rappel sur la necessite de la compensation et les procedes existants, la realisation controlee des detecteurs epais par compensation nucleaire est decrite en detail sous l'aspect theorique et l'aspect experimental. On met en evidence les precautions a prendre dans la pratique: controle de l'homogeneite du materiau de base, controle de l'evolution de la compensation, elimination des processus parasites. On etudie ensuite les performances de detecteurs obtenus : caracteristiques electriques (courant, duree de vie) d'une part, d'autre part detection et spectrometrie des rayonnements penetrants. Les resultats montrent que les diodes compensees ayant une epaisseur utile de deux

  9. Study of thick, nuclear-compensated silicon detectors; Etude des detecteurs epais au silicium compense nucleairement

    Le Coroller, Y [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires

    1964-09-01

    A study is made here, from the point of view of the realization and the performance, of thick nuclear-compensated silicon detectors. After recalling the need for compensation and reviewing the existing methods, the author describes in detail the controlled realization of thick detectors by nuclear compensation from the theoretical and experimental points of view. The practical precautions which should be observed are given: control of the homogeneity of the starting material, control of the evolution of the compensation, elimination of parasitic processes. The performances of the detectors obtained are then studied: electrical characteristics (current, life-time) on the one hand, detection and spectrometry of penetrating radiations on the other hand. The results show, that the compensated diodes having an effective thickness of two millimeters operate satisfactorily as detectors for applied voltages of about 500 volts. The resolutions observed are then about 2 per cent for mono-energetic electrons and about 4 per cent for the gamma; they can be improved by the use of a pre-amplifier of very low background noise. (author) [French] Les detecteurs epais au silicium compense nucleairement sont etudies ici du double point de vue realisation et performances. Apres un rappel sur la necessite de la compensation et les procedes existants, la realisation controlee des detecteurs epais par compensation nucleaire est decrite en detail sous l'aspect theorique et l'aspect experimental. On met en evidence les precautions a prendre dans la pratique: controle de l'homogeneite du materiau de base, controle de l'evolution de la compensation, elimination des processus parasites. On etudie ensuite les performances de detecteurs obtenus : caracteristiques electriques (courant, duree de vie) d'une part, d'autre part detection et spectrometrie des rayonnements penetrants. Les resultats montrent que les diodes compensees ayant une epaisseur utile de deux millimetres fonctionnent

  10. Remote sensing for oil spill detection and response

    Engelhardt, F.R.

    1999-01-01

    This paper focuses on the use of remote sensing for marine oil spill detection and response. The surveillance and monitoring of discharges, and the main elements of effective surveillance are discussed. Tactical emergency response and the requirements for selecting a suitable remote sensing approach, airborne remote sensing systems, and the integration of satellite and airborne imaging are examined. Specifications of satellite surveillance systems potentially usable for oil spill detection, and specifications of airborne remote sensing systems suitable for oil spill detection, monitoring and supplemental actions are tabulated, and a schema of integrated satellite-airborne remote sensing (ISARS) is presented. (UK)

  11. Compensating for the harms of family violence: statutory barriers in Australian victims of crime compensation schemes.

    Forster, Christine

    2014-09-01

    This article considers the compensative capacity of the victims of crime statutory schemes that are present in all eight Australian jurisdictions for primary victims of family violence. It argues that the recommendations of the Final Report on Family Violence conducted jointly by the Australian Law Reform Commission and the New South Wales Law Reform Commission in 2010, although a positive step, are insufficient to facilitate meaningful compensation to victims of family violence. In addition to the primary limitations identified by the Commissions--a requirement to report the crime to the police within a reasonable time and a requirement for multiple acts of violence to be reduced to a single act if they are related--there are other statutory barriers that disproportionately disadvantage victims of family violence. These include time limitation provisions, a requirement to report the crime to police, the restriction of compensation to prescribed categories of loss which exclude many of the social, vocational, emotional and psychological harms suffered by victims of family violence, and significant cut-backs on the non-economic component of the schemes. This article further argues that the statutory barriers cumulatively contribute to the perception of a crime as an isolated event perpetrated by a deviant individual. The article recommends that specific provisions for family violence victims should be introduced into all schemes including three categories of compensation not tied to criminal offences but rather the different forms of family violence, with a generous compensation range, and no requirement for proof of injury.

  12. Lunar remote sensing and measurements

    Moore, H.J.; Boyce, J.M.; Schaber, G.G.; Scott, D.H.

    1980-01-01

    Remote sensing and measurements of the Moon from Apollo orbiting spacecraft and Earth form a basis for extrapolation of Apollo surface data to regions of the Moon where manned and unmanned spacecraft have not been and may be used to discover target regions for future lunar exploration which will produce the highest scientific yields. Orbital remote sensing and measurements discussed include (1) relative ages and inferred absolute ages, (2) gravity, (3) magnetism, (4) chemical composition, and (5) reflection of radar waves (bistatic). Earth-based remote sensing and measurements discussed include (1) reflection of sunlight, (2) reflection and scattering of radar waves, and (3) infrared eclipse temperatures. Photographs from the Apollo missions, Lunar Orbiters, and other sources provide a fundamental source of data on the geology and topography of the Moon and a basis for comparing, correlating, and testing the remote sensing and measurements. Relative ages obtained from crater statistics and then empirically correlated with absolute ages indicate that significant lunar volcanism continued to 2.5 b.y. (billion years) ago-some 600 m.y. (million years) after the youngest volcanic rocks sampled by Apollo-and that intensive bombardment of the Moon occurred in the interval of 3.84 to 3.9 b.y. ago. Estimated fluxes of crater-producing objects during the last 50 m.y. agree fairly well with fluxes measured by the Apollo passive seismic stations. Gravity measurements obtained by observing orbiting spacecraft reveal that mare basins have mass concentrations and that the volume of material ejected from the Orientale basin is near 2 to 5 million km 3 depending on whether there has or has not been isostatic compensation, little or none of which has occurred since 3.84 b.y. ago. Isostatic compensation may have occurred in some of the old large lunar basins, but more data are needed to prove it. Steady fields of remanent magnetism were detected by the Apollo 15 and 16 subsatellites

  13. Executive compensation and firm performance: Evidence from Indian firms

    Mehul Raithatha

    2016-09-01

    Full Text Available The study examines the relationship between executive compensation and firm performance among Indian firms. The evidence suggests that firm performance measured by accounting, as well as market-based measures, significantly affects executive compensation. We also test for the presence of persistence in executive compensation by employing the system-generalised methods of moments (GMM estimator. We find significant persistence in executive compensation among the sample firms. Further, we report the absence of pay–performance relationship among the smaller sample firms and business group affiliated firms. Thus, our findings cast doubts over the performance-based executive compensation practices of Indian business group affiliated firms.

  14. Aberration compensation of an ultrasound imaging instrument with a reduced number of channels.

    Jiang, Wei; Astheimer, Jeffrey P; Waag, Robert C

    2012-10-01

    Focusing and imaging qualities of an ultrasound imaging system that uses aberration correction were experimentally investigated as functions of the number of parallel channels. Front-end electronics that consolidate signals from multiple physical elements can be used to lower hardware and computational costs by reducing the number of parallel channels. However, the signals from sparse arrays of synthetic elements yield poorer aberration estimates. In this study, aberration estimates derived from synthetic arrays of varying element sizes are evaluated by comparing compensated receive focuses, compensated transmit focuses, and compensated b-scan images of a point target and a cyst phantom. An array of 80 x 80 physical elements with a pitch of 0.6 x 0.6 mm was used for all of the experiments and the aberration was produced by a phantom selected to mimic propagation through abdominal wall. The results show that aberration correction derived from synthetic arrays with pitches that have a diagonal length smaller than 70% of the correlation length of the aberration yield focuses and images of approximately the same quality. This connection between correlation length of the aberration and synthetic element size provides a guideline for determining the number of parallel channels that are required when designing imaging systems that employ aberration correction.

  15. Position error compensation via a variable reluctance sensor applied to a Hybrid Vehicle Electric machine.

    Bucak, Ihsan Ömür

    2010-01-01

    In the automotive industry, electromagnetic variable reluctance (VR) sensors have been extensively used to measure engine position and speed through a toothed wheel mounted on the crankshaft. In this work, an application that already uses the VR sensing unit for engine and/or transmission has been chosen to infer, this time, the indirect position of the electric machine in a parallel Hybrid Electric Vehicle (HEV) system. A VR sensor has been chosen to correct the position of the electric machine, mainly because it may still become critical in the operation of HEVs to avoid possible vehicle failures during the start-up and on-the-road, especially when the machine is used with an internal combustion engine. The proposed method uses Chi-square test and is adaptive in a sense that it derives the compensation factors during the shaft operation and updates them in a timely fashion.

  16. Position Error Compensation via a Variable Reluctance Sensor Applied to a Hybrid Vehicle Electric Machine

    İhsan Ömür Bucak

    2010-03-01

    Full Text Available In the automotive industry, electromagnetic variable reluctance (VR sensors have been extensively used to measure engine position and speed through a toothed wheel mounted on the crankshaft. In this work, an application that already uses the VR sensing unit for engine and/or transmission has been chosen to infer, this time, the indirect position of the electric machine in a parallel Hybrid Electric Vehicle (HEV system. A VR sensor has been chosen to correct the position of the electric machine, mainly because it may still become critical in the operation of HEVs to avoid possible vehicle failures during the start-up and on-the-road, especially when the machine is used with an internal combustion engine. The proposed method uses Chi-square test and is adaptive in a sense that it derives the compensation factors during the shaft operation and updates them in a timely fashion.

  17. Compensation for oil pollution damage caused by oil spills from ships and the International Oil Pollution Compensation Fund

    Jacobsson, M.

    1994-01-01

    Liability and compensation for pollution damage caused by oil spills from laden tankers is governed by two international conventions: the 1969 Civil Liability Convention and the 1971 Fund Convention. The Civil Liability Convention established a system of strict liability for tanker owners and introduced compulsory liability insurance. The Fund Convention created a system of supplementary compensation administered by an intergovernmental organization, the International Oil Pollution Compensation Fund (IOPC Fund), which at present has 56 member states (August 1993). The IOPC Fund pays compensation to victims of oil pollution in member states when the compensation from the ship owner and his insurer is insufficient. (author)

  18. Healing or harming? Healthcare provider interactions with injured workers and insurers in workers' compensation systems.

    Kilgour, Elizabeth; Kosny, Agnieszka; McKenzie, Donna; Collie, Alex

    2015-03-01

    Healthcare providers (HCPs) are influential in the injured worker's recovery process and fulfil many roles in the delivery of health services. Interactions between HCPs and insurers can also affect injured workers' engagement in rehabilitation and subsequently their recovery and return to work. Consideration of the injured workers' perceptions and experiences as consumers of medical and compensation services can provide vital information about the quality, efficacy and impact of such systems. The aim of this systematic review was to identify and synthesize published qualitative research that focused on the interactions between injured workers, HCPs and insurers in workers' compensation systems in order to identify processes or interactions which impact injured worker recovery. A search of six electronic databases for literature published between 1985 and 2012 revealed 1,006 articles. Screening for relevance identified 27 studies which were assessed for quality against set criteria. A final 13 articles of medium and high quality were retained for data extraction. Findings were synthesized using a meta-ethnographic approach. Injured workers reported that HCPs could play both healing and harming roles in their recovery. Supportive patient-centred interaction with HCPs is important for injured workers. Difficult interactions between HCPs and insurers were highlighted in themes of adversarial relations and organisational pressures. Insurer and compensation system processes exerted an influence on the therapeutic relationship. Recommendations to improve relationships included streamlining administrative demands and increasing education and communication between the parties. Injured workers with long term complex injuries experience difficulties with healthcare in the workers' compensation context. Changes in insurer administrative demands and compensation processes could increase HCP participation and job satisfaction. This in turn may improve injured worker recovery

  19. Accommodating practical constraints for intensity modulated radiation therapy by means of compensators

    Meyer, Juergen

    2002-01-01

    The thesis deals with the practical implementation of intensity modulated radiation therapy (IMRT) generated by means of patient specific metal compensators. An elaborate comparison between several compensator-machining techniques, with respect to their suitability for production within a hospital workshop, is presented. The limitations associated with the selected compensator manufacturing technique are identified and implemented as constraints in an existing inverse treatment-planning algorithm. In order to obtain the profile of a compensator, which produces a desired intensity distribution, inverse modeling of the radiation attenuation within the compensator is required. Two novel and independent approaches, based on deconvolution and system identification, are proposed to accomplish this. To compare the approach with the 'rival' state of the art beam modulation technique, a theoretical and experimental examination of the modulated fields generated by manufactured compensators and multileaf collimators is presented. This comparison focused on the achievable resolution of the intensity modulated beams in lateral and longitudinal directions. To take into account the characteristics of a clinical environment the suitability of the most common commercially available treatment couch systems for IMRT treatments is studied. An original rule based advisory system is developed to alert the operator of any potential collision of the beam with the movable supporting structures of the treatment couch. The system is capable of finding alternative positions for the supporting frames and, if necessary, can suggest alternative beam directions. Finally, a head and neck phantom is designed for gel dosimetry to assess IMRT treatment delivery techniques. The phantom is based on a simplistic but realistic design and contains the main anatomical features

  20. Illumination compensation in ground based hyperspectral imaging

    Wendel, Alexander; Underwood, James

    2017-07-01

    Hyperspectral imaging has emerged as an important tool for analysing vegetation data in agricultural applications. Recently, low altitude and ground based hyperspectral imaging solutions have come to the fore, providing very high resolution data for mapping and studying large areas of crops in detail. However, these platforms introduce a unique set of challenges that need to be overcome to ensure consistent, accurate and timely acquisition of data. One particular problem is dealing with changes in environmental illumination while operating with natural light under cloud cover, which can have considerable effects on spectral shape. In the past this has been commonly achieved by imaging known reference targets at the time of data acquisition, direct measurement of irradiance, or atmospheric modelling. While capturing a reference panel continuously or very frequently allows accurate compensation for illumination changes, this is often not practical with ground based platforms, and impossible in aerial applications. This paper examines the use of an autonomous unmanned ground vehicle (UGV) to gather high resolution hyperspectral imaging data of crops under natural illumination. A process of illumination compensation is performed to extract the inherent reflectance properties of the crops, despite variable illumination. This work adapts a previously developed subspace model approach to reflectance and illumination recovery. Though tested on a ground vehicle in this paper, it is applicable to low altitude unmanned aerial hyperspectral imagery also. The method uses occasional observations of reference panel training data from within the same or other datasets, which enables a practical field protocol that minimises in-field manual labour. This paper tests the new approach, comparing it against traditional methods. Several illumination compensation protocols for high volume ground based data collection are presented based on the results. The findings in this paper are

  1. Disclosed Values of Option-Based Compensation

    Bechmann, Ken L.; Hjortshøj, Toke Lilhauge

    New accounting standards require firms to expense the costs of option-based compensation (OBC), but the associated valuations offer many challenges for firms. Earlier research has documented that firms in the U.S. generally underreport the values of OBC by manipulating the inputs used for valuation......-Scholes parameters in their valuations. Furthermore, firms determine the expected time to maturity in a way that is generally consistent with the guidelines provided by the new accounting standards. The findings differ from those of the U.S., but is consistent with the more limited use of OBC and the lower level...

  2. No-fault compensation and performance review.

    Knight, B

    1993-01-01

    Two major issues in relation to medical malpractice are discussed. The first is "no-fault compensation", an alternative to the present tort system long established in most countries, including Singapore, where negligence must be proved before a claim can succeed. The second is "performance review", a new concept for monitoring and correcting under-performing medical practitioners against whom a complaint has been laid. Both these issues are currently under active discussion and are arousing political notice and professional controversy. Though the article describes the British situation, there is much of contemporary relevance for Singapore, which has such a similar system of medical practice.

  3. Hybrid compensation arrangement in dispersed generation systems

    Chen, Zhe; Blaabjerg, Frede; Pedersen, John Kim

    2005-01-01

    This paper presents a hybrid compensation system consisting of an active filter and distributed passive filters. In the system, each individual passive filter is connected to a distortion source and designed to eliminate main harmonics and supply reactive power for the distortion source, while...... filter system consisting of distributed passive filters and an active filter....... the active filter is responsible for the correction of the system unbalance and the cancellation of the remaining harmonics. The paper also analyzes the effects of the circuit configuration on the system impedance characteristics and consequently the effectiveness of the filter system. Simulation studies...

  4. DC-Compensated Current Transformer †

    Ripka, Pavel; Draxler, Karel; Styblíková, Renata

    2016-01-01

    Instrument current transformers (CTs) measure AC currents. The DC component in the measured current can saturate the transformer and cause gross error. We use fluxgate detection and digital feedback compensation of the DC flux to suppress the overall error to 0.15%. This concept can be used not only for high-end CTs with a nanocrystalline core, but it also works for low-cost CTs with FeSi cores. The method described here allows simultaneous measurements of the DC current component. PMID:26805830

  5. Focused ultrasound in ophthalmology

    Silverman RH

    2016-09-01

    Full Text Available Ronald H Silverman1,2 1Department of Ophthalmology, Columbia University Medical Center, 2F.L. Lizzi Center for Biomedical Engineering, Riverside Research, New York, NY, USA Abstract: The use of focused ultrasound to obtain diagnostically significant information about the eye goes back to the 1950s. This review describes the historical and technological development of ophthalmic ultrasound and its clinical application and impact. Ultrasound, like light, can be focused, which is crucial for formation of high-resolution, diagnostically useful images. Focused, single-element, mechanically scanned transducers are most common in ophthalmology. Specially designed transducers have been used to generate focused, high-intensity ultrasound that through thermal effects has been used to treat glaucoma (via cilio-destruction, tumors, and other pathologies. Linear and annular transducer arrays offer synthetic focusing in which precise timing of the excitation of independently addressable array elements allows formation of a converging wavefront to create a focus at one or more programmable depths. Most recently, linear array-based plane-wave ultrasound, in which the array emits an unfocused wavefront and focusing is performed solely on received data, has been demonstrated for imaging ocular anatomy and blood flow. While the history of ophthalmic ultrasound extends back over half-a-century, new and powerful technologic advances continue to be made, offering the prospect of novel diagnostic capabilities. Keywords: ophthalmic ultrasound, ultrasound biomicroscopy (UBM, high-intensity focused ultrasound (HIFU, ultrafast imaging, Doppler imaging 

  6. Space Focus Lead Report

    Reeves, Geoffrey D. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

    2017-08-10

    The Space Focus team is tasked with the definition of the Space Focused Science Topics, and with the review and ranking of the CSES proposals received in all the program areas. This is achieved by dedicated meetings or a series of informal discussions and/or e-mail reviews.

  7. BrightFocus Foundation

    ... About BrightFocus Foundation Featured Content BrightFocus: Investing in Science to Save Mind and Sight We're here to help. Explore ... recognition is very important. Monday, November 6, 2017 New Diagnosis? Managing a mind and sight disease is a journey. And you’ ...

  8. Optical remote sensing

    Prasad, Saurabh; Chanussot, Jocelyn

    2011-01-01

    Optical remote sensing relies on exploiting multispectral and hyper spectral imagery possessing high spatial and spectral resolutions respectively. These modalities, although useful for most remote sensing tasks, often present challenges that must be addressed for their effective exploitation. This book presents current state-of-the-art algorithms that address the following key challenges encountered in representation and analysis of such optical remotely sensed data: challenges in pre-processing images, storing and representing high dimensional data, fusing different sensor modalities, patter

  9. REMOTE SENSING IN OCEANOGRAPHY.

    remote sensing from satellites. Sensing of oceanographic variables from aircraft began with the photographing of waves and ice. Since then remote measurement of sea surface temperatures and wave heights have become routine. Sensors tested for oceanographic applications include multi-band color cameras, radar scatterometers, infrared spectrometers and scanners, passive microwave radiometers, and radar imagers. Remote sensing has found its greatest application in providing rapid coverage of large oceanographic areas for synoptic and analysis and

  10. Remote Sensing of Ecology, Biodiversity and Conservation: A Review from the Perspective of Remote Sensing Specialists

    Marc Cattet

    2010-11-01

    Full Text Available Remote sensing, the science of obtaining information via noncontact recording, has swept the fields of ecology, biodiversity and conservation (EBC. Several quality review papers have contributed to this field. However, these papers often discuss the issues from the standpoint of an ecologist or a biodiversity specialist. This review focuses on the spaceborne remote sensing of EBC from the perspective of remote sensing specialists, i.e., it is organized in the context of state-of-the-art remote sensing technology, including instruments and techniques. Herein, the instruments to be discussed consist of high spatial resolution, hyperspectral, thermal infrared, small-satellite constellation, and LIDAR sensors; and the techniques refer to image classification, vegetation index (VI, inversion algorithm, data fusion, and the integration of remote sensing (RS and geographic information system (GIS.

  11. Remote sensing of ecology, biodiversity and conservation: a review from the perspective of remote sensing specialists.

    Wang, Kai; Franklin, Steven E; Guo, Xulin; Cattet, Marc

    2010-01-01

    Remote sensing, the science of obtaining information via noncontact recording, has swept the fields of ecology, biodiversity and conservation (EBC). Several quality review papers have contributed to this field. However, these papers often discuss the issues from the standpoint of an ecologist or a biodiversity specialist. This review focuses on the spaceborne remote sensing of EBC from the perspective of remote sensing specialists, i.e., it is organized in the context of state-of-the-art remote sensing technology, including instruments and techniques. Herein, the instruments to be discussed consist of high spatial resolution, hyperspectral, thermal infrared, small-satellite constellation, and LIDAR sensors; and the techniques refer to image classification, vegetation index (VI), inversion algorithm, data fusion, and the integration of remote sensing (RS) and geographic information system (GIS).

  12. Boron doping compensation of hydrogenated amorphous and polymorphous germanium thin films for infrared detection applications

    Moreno, M.; Delgadillo, N.; Torres, A.; Ambrosio, R.; Rosales, P.; Kosarev, A.; Reyes-Betanzo, C.; Hidalga-Wade, J. de la; Zuniga, C.; Calleja, W.

    2013-01-01

    In this work we have studied boron doping of hydrogenated amorphous germanium a-Ge:H and polymorphous germanium (pm-Ge:H) in low regimes, in order to compensate the material from n-type (due to oxygen contamination that commonly occurs during plasma deposition) to intrinsic, and in this manner improve the properties that are important for infrared (IR) detection, as activation energy (E a ) and temperature coefficient of resistance (TCR). Electrical, structural and optical characterization was performed on the films produced. Measurements of the temperature dependence of conductivity, room temperature conductivity (σ RT ), E a and current–voltage characteristics under IR radiation were performed in the compensated a-Ge:H and pm-Ge:H films. Our results demonstrate that, effectively, the values of E a , TCR and IR detection are improved on the a-Ge:H/pm-Ge:H films, using boron doping in low regimes, which results of interest for infrared detectors. - Highlights: • We reported boron doping compensation of amorphous and polymorphous germanium. • The films were deposited by plasma enhanced chemical vapor deposition. • The aim is to use the films as thermo-sensing elements in un-cooled microbolometers. • Those films have advantages over boron doped a-Si:H used in commercial detectors

  13. The role of whiskers in compensation of visual deficit in a mouse model of retinal degeneration.

    Voller, Jaroslav; Potužáková, Barbora; Šimeček, Vojtěch; Vožeh, František

    2014-01-13

    Sensory deprivation in one modality can enhance the development of the remaining modalities via mechanisms of synaptic plasticity. Mice of the C3H strain suffer from RD1 retinal degeneration that leads to visual impairment at weaning age. We examined a role of whiskers in compensation of the visual deficit. In order to differentiate the contribution of the whiskers from other mechanisms that can take part in the compensation, we investigated the effect of both chronic and acute tactile deprivation. Three-month-old mice were used. We examined motor skills (rotarod, beam walking test), gait control (CatWalk system), spontaneous motor activity (open field) and CNS excitability to an acoustic stimulus for assessment of compensatory changes in auditory system (audiogenic epilepsy). In the sighted mice, the only effect was a decline in their rotarod test performance after acute whisker removal. In the blind animals, chronic tactile deprivation caused changes in their gait and impaired the performance in motor tests. Some other compensatory mechanisms were involved but the whiskers are essential for the compensation as it emerged from more marked change of gait and the worsening of the motor performance after the acute whisker removal. Both chronic and acute tactile deprivation induced anxiety-like behaviour. Only a combination of blindness and chronic tactile deprivation led to an increased sense of hearing. Copyright © 2013 Elsevier Ireland Ltd. All rights reserved.

  14. Boron doping compensation of hydrogenated amorphous and polymorphous germanium thin films for infrared detection applications

    Moreno, M., E-mail: mmoreno@inaoep.mx [National Institute of Astrophysics, Optics and Electronics, INAOE, P.O. Box 51 and 216, Puebla, Z. P. 72840 Puebla (Mexico); Delgadillo, N. [Universidad Autónoma de Tlaxcala, Av. Universidad No. 1, Z. P. 90006 Tlaxcala (Mexico); Torres, A. [National Institute of Astrophysics, Optics and Electronics, INAOE, P.O. Box 51 and 216, Puebla, Z. P. 72840 Puebla (Mexico); Ambrosio, R. [Technology and Engineering Institute, Ciudad Juarez University UACJ, Av. Del Charro 450N, Z. P. 32310 Chihuahua (Mexico); Rosales, P.; Kosarev, A.; Reyes-Betanzo, C.; Hidalga-Wade, J. de la; Zuniga, C.; Calleja, W. [National Institute of Astrophysics, Optics and Electronics, INAOE, P.O. Box 51 and 216, Puebla, Z. P. 72840 Puebla (Mexico)

    2013-12-02

    In this work we have studied boron doping of hydrogenated amorphous germanium a-Ge:H and polymorphous germanium (pm-Ge:H) in low regimes, in order to compensate the material from n-type (due to oxygen contamination that commonly occurs during plasma deposition) to intrinsic, and in this manner improve the properties that are important for infrared (IR) detection, as activation energy (E{sub a}) and temperature coefficient of resistance (TCR). Electrical, structural and optical characterization was performed on the films produced. Measurements of the temperature dependence of conductivity, room temperature conductivity (σ{sub RT}), E{sub a} and current–voltage characteristics under IR radiation were performed in the compensated a-Ge:H and pm-Ge:H films. Our results demonstrate that, effectively, the values of E{sub a}, TCR and IR detection are improved on the a-Ge:H/pm-Ge:H films, using boron doping in low regimes, which results of interest for infrared detectors. - Highlights: • We reported boron doping compensation of amorphous and polymorphous germanium. • The films were deposited by plasma enhanced chemical vapor deposition. • The aim is to use the films as thermo-sensing elements in un-cooled microbolometers. • Those films have advantages over boron doped a-Si:H used in commercial detectors.

  15. Combined TiN- and TaN temperature compensated thin film resistors

    Malmros, Anna; Andersson, Kristoffer; Rorsman, Niklas

    2012-01-01

    The opposite signs of the temperature coefficient of resistance (TCR) of two thin film materials, titanium nitride (TiN) and tantalum nitride (TaN), were used to form temperature compensated thin film resistors (TFRs). The principle of designing temperature compensated TFRs by connecting TFRs of each compound in series or in parallel was demonstrated. TiN, TaN, and combined TiN and TaN TFRs for monolithic microwave integrated circuits (MMICs) were fabricated by reactive sputtering. DC characterization was performed over the temperature range of 30–200 °C. The TiN TFRs exhibited an increase in resistivity with temperature with TCRs of 540 and 750 ppm/°C. The TaN TFR on the other hand exhibited a negative TCR of − 470 ppm/°C. The shunted TFRs were fabricated by serial deposition of TiN and TaN to form a bilayer component. The TCRs of the series- and shunt configurations were experimentally reduced to − 60 and 100 ppm/°C, respectively. The concept of temperature compensation was used to build a Wheatstone bridge with an application in on-chip temperature sensing.

  16. Compensating for Thalamocortical Synaptic Loss in Alzheimer’s Disease

    Kamal eAbuhassan

    2014-06-01

    Full Text Available The study presents a thalamocortical network model which oscillates within the alpha frequency band (8-13 Hz as recorded in the wakeful relaxed state with closed eyes to study the neural causes of abnormal oscillatory activity in Alzheimer’s disease (AD. Incorporated within the model are various types of cortical excitatory and inhibitory neurons, recurrently connected to thalamic and reticular thalamic regions with the ratios and distances derived from the mammalian thalamocortical system. The model is utilized to study the impacts of four types of connectivity loss on the model’s spectral dynamics. The study focuses on investigating degeneration of corticocortical, thalamocortical, corticothalamic and corticoreticular couplings, with an emphasis on the influence of each modelled case on the spectral output of the model. Synaptic compensation has been included in each model to examine the interplay between synaptic deletion and compensation mechanisms, and the oscillatory activity of the network. The results of power spectra and event related desynchronisation/synchronisation (ERD/S analyses show that the dynamics of the thalamic and cortical oscillations are significantly influenced by corticocortical synaptic loss. Interestingly, the patterns of changes in thalamic spectral activity are correlated with those in the cortical model. Similarly, the thalamic oscillatory activity is diminished after partial corticothalamic denervation. The results suggest that thalamic atrophy is a secondary pathology to cortical shrinkage in Alzheimer’s disease. In addition, this study finds that the inhibition from neurons in the thalamic reticular nucleus (RTN to thalamic relay (TCR neurons plays a key role in regulating thalamic oscillations; disinhibition disrupts thalamic oscillatory activity even though TCR neurons are more depolarized after being released from RTN inhibition. This study provides information that can be explored experimentally to

  17. Metal oxide nanostructures as gas sensing devices

    Eranna, G

    2016-01-01

    Metal Oxide Nanostructures as Gas Sensing Devices explores the development of an integrated micro gas sensor that is based on advanced metal oxide nanostructures and is compatible with modern semiconductor fabrication technology. This sensor can then be used to create a compact, low-power, handheld device for analyzing air ambience. The book first covers current gas sensing tools and discusses the necessity for miniaturized sensors. It then focuses on the materials, devices, and techniques used for gas sensing applications, such as resistance and capacitance variations. The author addresses the issues of sensitivity, concentration, and temperature dependency as well as the response and recovery times crucial for sensors. He also presents techniques for synthesizing different metal oxides, particularly those with nanodimensional structures. The text goes on to highlight the gas sensing properties of many nanostructured metal oxides, from aluminum and cerium to iron and titanium to zinc and zirconium. The final...

  18. Predictors of Energy Compensation during Exercise Interventions: A Systematic Review

    Marie-Ève Riou

    2015-05-01

    Full Text Available Weight loss from exercise-induced energy deficits is usually less than expected. The objective of this systematic review was to investigate predictors of energy compensation, which is defined as body energy changes (fat mass and fat-free mass over the total amount of exercise energy expenditure. A search was conducted in multiple databases without date limits. Of 4745 studies found, 61 were included in this systematic review with a total of 928 subjects. The overall mean energy compensation was 18% ± 93%. The analyses indicated that 48% of the variance of energy compensation is explained by the interaction between initial fat mass, age and duration of exercise interventions. Sex, frequency, intensity and dose of exercise energy expenditure were not significant predictors of energy compensation. The fitted model suggested that for a shorter study duration, lower energy compensation was observed in younger individuals with higher initial fat mass (FM. In contrast, higher energy compensation was noted for younger individuals with lower initial FM. From 25 weeks onward, energy compensation was no longer different for these predictors. For studies of longer duration (about 80 weeks, the energy compensation approached 84%. Lower energy compensation occurs with short-term exercise, and a much higher level of energy compensation accompanies long-term exercise interventions.

  19. Report of the working group for nuclear damage compensation system

    1989-01-01

    The Working Group for Nuclear Damage Compensation System was established within the Atomic Energy Commision of Japan on August 2, 1988. The Group has held five meetings to make a study on the revision of the reserve for nuclear damage compensation. The nuclear damage compensation system in Japan has been established under the Law Concerning Compensation for Nuclear Damages and the Law Concerning Contract for Compensation for Nuclear Damages. The former law requires the nuclear power plant operators to set up a reserve for damage compensation to ensure positive and quick payment of compensation in the event of an accident. The reserve is currently rely on liability insurance and a government compensation contract. The Working Group has concluded that the total reserve should be increased from the current yen10 bill. to yen30 bill. The amount of the reserve specified in the enforcement law for the Law Concerning Compensation for Nuclear Damages should also be increased accordingly. The Law Concerning compensation for Nuclear damage will also be applied to damage which occurs overseas as a result of an accident in Japan. (N.K.)

  20. Hyperspectral sensing of forests

    Goodenough, David G.; Dyk, Andrew; Chen, Hao; Hobart, Geordie; Niemann, K. Olaf; Richardson, Ash

    2007-11-01

    Canada contains 10% of the world's forests covering an area of 418 million hectares. The sustainable management of these forest resources has become increasingly complex. Hyperspectral remote sensing can provide a wealth of new and improved information products to resource managers to make more informed decisions. Research in this area has demonstrated that hyperspectral remote sensing can be used to create more accurate products for forest inventory, forest health, foliar biochemistry, biomass, and aboveground carbon than are currently available. This paper surveys recent methods and results in hyperspectral sensing of forests and describes space initiatives for hyperspectral sensing.

  1. LIGO sensing system performance

    Landry, M

    2002-01-01

    The optical sensing subsystem of a LIGO interferometer is described. The system includes two complex interferometric sensing schemes to control test masses in length and alignment. The length sensing system is currently employed on all LIGO interferometers to lock coupled cavities on resonance. Auto-alignment is to be accomplished by a wavefront-sensing scheme which automatically corrects for angular fluctuations of the test masses. Improvements in lock stability and duration are noted when the wavefront auto-alignment system is employed. Preliminary results from the commissioning of the 2 km detector in Washington are shown.

  2. Intelligent environmental sensing

    Mukhopadhyay, Subhas

    2015-01-01

    Developing environmental sensing and monitoring technologies become essential especially for industries that may cause severe contamination. Intelligent environmental sensing uses novel sensor techniques, intelligent signal and data processing algorithms, and wireless sensor networks to enhance environmental sensing and monitoring. It finds applications in many environmental problems such as oil and gas, water quality, and agriculture. This book addresses issues related to three main approaches to intelligent environmental sensing and discusses their latest technological developments. Key contents of the book include:   Agricultural monitoring Classification, detection, and estimation Data fusion Geological monitoring Motor monitoring Multi-sensor systems Oil reservoirs monitoring Sensor motes Water quality monitoring Wireless sensor network protocol  

  3. Advanced Remote Sensing Research

    Slonecker, Terrence; Jones, John W.; Price, Susan D.; Hogan, Dianna

    2008-01-01

    'Remote sensing' is a generic term for monitoring techniques that collect information without being in physical contact with the object of study. Overhead imagery from aircraft and satellite sensors provides the most common form of remotely sensed data and records the interaction of electromagnetic energy (usually visible light) with matter, such as the Earth's surface. Remotely sensed data are fundamental to geographic science. The Eastern Geographic Science Center (EGSC) of the U.S. Geological Survey (USGS) is currently conducting and promoting the research and development of three different aspects of remote sensing science: spectral analysis, automated orthorectification of historical imagery, and long wave infrared (LWIR) polarimetric imagery (PI).

  4. Optical Remote Sensing Laboratory

    Federal Laboratory Consortium — The Optical Remote Sensing Laboratory deploys rugged, cutting-edge electro-optical instrumentation for the collection of various event signatures, with expertise in...

  5. Doing good buffers against feeling bad : prosocial impact compensates for negative task and self-evaluations

    Grant, Adam M.; Sonnentag, Sabine

    2010-01-01

    Although evidence suggests that negative task and self-evaluations are associated with emotional exhaustion, little research has examined factors that buffer against these affects. We propose that perceived prosocial impact, the experience of helping others, compensates for negative task and self-evaluations by focusing attention on positive outcomes for others. In Study 1, perceived prosocial impact attenuated the associations of low intrinsic motivation and core self-evaluations with emotio...

  6. Fixman compensating potential for general branched molecules

    Jain, Abhinandan, E-mail: Abhi.Jain@jpl.nasa.gov [Jet Propulsion Laboratory, California Institute of Technology, 4800 Oak Grove Drive, Pasadena, California 91109 (United States); Kandel, Saugat; Wagner, Jeffrey; Larsen, Adrien; Vaidehi, Nagarajan, E-mail: nvaidehi@coh.org [Division of Immunology, Beckman Research Institute of the City of Hope, Duarte, California 91010 (United States)

    2013-12-28

    The technique of constraining high frequency modes of molecular motion is an effective way to increase simulation time scale and improve conformational sampling in molecular dynamics simulations. However, it has been shown that constraints on higher frequency modes such as bond lengths and bond angles stiffen the molecular model, thereby introducing systematic biases in the statistical behavior of the simulations. Fixman proposed a compensating potential to remove such biases in the thermodynamic and kinetic properties calculated from dynamics simulations. Previous implementations of the Fixman potential have been limited to only short serial chain systems. In this paper, we present a spatial operator algebra based algorithm to calculate the Fixman potential and its gradient within constrained dynamics simulations for branched topology molecules of any size. Our numerical studies on molecules of increasing complexity validate our algorithm by demonstrating recovery of the dihedral angle probability distribution function for systems that range in complexity from serial chains to protein molecules. We observe that the Fixman compensating potential recovers the free energy surface of a serial chain polymer, thus annulling the biases caused by constraining the bond lengths and bond angles. The inclusion of Fixman potential entails only a modest increase in the computational cost in these simulations. We believe that this work represents the first instance where the Fixman potential has been used for general branched systems, and establishes the viability for its use in constrained dynamics simulations of proteins and other macromolecules.

  7. Background compensation methodologies for contamination monitoring systems

    Raman, Anand; Chaudhury, Probal; Pradeepkumar, K.S.

    2014-01-01

    Radiation surveillance program in the various nuclear facilities incorporate contamination monitoring as an important component. Contamination monitoring programs constitute monitoring for alpha and beta contamination of the physical entities associated with the working personnel that include his hands, feet, clothing, shoes as well as the general surface areas in the working environment like floors. All these measurements are fraught with the contribution of the ambient gamma background radiation fields. These inhibit a proper and precise estimation of the contamination concentration being monitored. This paper investigates the efficacy of two methodologies that have been incorporated in two of the contamination monitoring systems developed in the Division. In the first system discussed, a high degree of gamma compensation has been achieved for an uniform exposure of the order of 50 nSv/hr to 100 mSv/hr. In the second system discussed, the degree of gamma compensation achieved is equal to those dictated by the statistical nature of the uncertainties associated with the subtraction of background from the source data. These two methods can be very effectively employed depending on the application requirement. A minimum detection level equivalent to 0.37 Bq/cdm 2 has been achieved in both these cases

  8. 76 FR 6009 - Shareholder Approval of Executive Compensation and Golden Parachute Compensation

    2011-02-02

    .... Consideration of Impact on the Economy, Burden on Competition, and Promotion of Efficiency, Competition, and... Act are available on our Web site at http://www.sec.gov/comments/df-title-ix/executive-compensation...\\ See, e.g., letters from International Corporate Governance Network (``ICGN'') and Teachers Insurance...

  9. Philosophy vs the common sense

    V. V. Chernyshov

    2017-01-01

    Full Text Available The paper deals with the antinomy of philosophy and the common sense. Philosophy emerges as a way of specifically human knowledge, which purposes analytics of the reality of subjective experience. The study reveals that in order to alienate philosophy from the common sense it was essential to revise the understanding of wisdom. The new, philosophical interpretation of wisdom – offered by Pythagoras – has laid the foundation of any future philosophy. Thus, philosophy emerges, alienating itself from the common sense, which refers to the common or collective experience. Moreover, the study examines the role of emotions, conformity and conventionality which they play with respect to the common sense. Next the author focuses on the role of philosophical intuition, guided with principles of rationality, nonconformity and scepticism, which the author professes the foundation stones of any sound philosophy. The common sense, described as deeply routed in the world of human emotions, aims at empathy, as the purpose of philosophy is to provide the rational means of knowledge. Therefore, philosophy uses thinking, keeping the permanent efforts to check and recheck data of its own experience. Thus, the first task of philosophical thinking appears to overcome the suggestion of the common sense, which purposes the social empathy, as philosophical intuition aims at independent thinking, the analytics of subjective experience. The study describes the fundamental principles of the common sense, on the one hand, and those of philosophy, on the other. The author arrives to conclusion that the common sense is unable to exceed the limits of sensual experience. Even there, where it apparently rises to a form of any «spiritual unity», even there it cannot avoid referring to the data of commonly shared sensual experience; though, philosophy, meanwhile, goes beyond sensuality, creating a discourse that would be able to alienate from it, and to make its rational

  10. Suppression of Instability on Sensing Signal of Optical Pulse Correlation Measurement in Remote Fiber Sensing

    Hirokazu Kobayashi

    2012-01-01

    response and improve the accuracy of signals at the focused sensing regions. We also experimentally demonstrate remote temperature monitoring over a 30 km-long distance using a remote reference technique, and we estimate the resolution and the measurable span of the temperature variation as (1.1/L∘C and (5.9×10/L°C, respectively, where L is the length of the fiber in the sensing region.

  11. An empirical study of desired versus actual compensation practices in determining intrapreneurial behaviour

    Ugochukwu O. Madu

    2014-08-01

    Full Text Available Orientation: Past research recognises that human resources management practices may influence innovative behaviour, particularly as compensation systems can be used as a tool to increase intrapreneurial activity. Research purpose: The aim of this study is to determine the relationship between actual versus desired compensation practices and elevated intrapreneurial behaviour. This is in line with research that focuses on how to promote business innovation, rather than merely research whether innovation is desirable for businesses or not. Motivation for the study: Recognising that entrepreneurial actions are the bedrock of intrapreneurial behaviour and that these behaviours may be critical to the long-term vitality of a firm and economy, it is important to facilitate the empirical study of them in an underresearched, emerging market environment. Moreover, compensation such as reward preferences and variable pay schemes remain controversial in terms of their costs versus contributions, and these constructs deserve more empirical research. Research approach, design and method: The study employed a quantitative research design, using a cross-sectional and empirical approach with primary data sources. A structured webbased instrument rendered a sample of 209 respondents from a diverse set of businesses. Canonical correlational analysis was carried out to test the hypotheses. Main findings: The results reveal that a gap exists between an employee’s perception of desired compensation practices and the actual compensation practices. The results further highlight that non-outcome-based measures like pay risk, job risk and expectations of success play a role in determining whether employees decide to be intrapreneurial or not. Practical/managerial implications: Due to the potential impact rewards have on intrapreneurial behaviour, it is necessary to design relevant compensation systems as part of organisational architecture in order to foster

  12. Motion compensated cine CMR of the fetal heart using radial undersampling and compressed sensing

    Roy, Christopher W.; Seed, Mike; Kingdom, John C.; Macgowan, Christopher K.

    2017-01-01

    Background To develop and evaluate a reconstruction framework for high resolution time-resolved CMR of the fetal heart in the presence of motion. Methods Data were acquired using a golden angle radial trajectory in seven fetal subjects and reconstructed as real-time images to detect fetal movement. Data acquired during through-plane motion were discarded whereas in-plane motion was corrected. A fetal cardiac gating signal was extracted to sort the corrected data by cardiac phase, allowing rec...

  13. A linear stepping endovascular intervention robot with variable stiffness and force sensing.

    He, Chengbin; Wang, Shuxin; Zuo, Siyang

    2018-03-08

    Robotic-assisted endovascular intervention surgery has attracted significant attention and interest in recent years. However, limited designs have focused on the variable stiffness mechanism of the catheter shaft. Flexible catheter needs to be partially switched to a rigid state that can hold its shape against external force to achieve a stable and effective insertion procedure. Furthermore, driving catheter in a similar way with manual procedures has the potential to make full use of the extensive experience from conventional catheter navigation. Besides driving method, force sensing is another significant factor for endovascular intervention. This paper presents a variable stiffness catheterization system that can provide stable and accurate endovascular intervention procedure with a linear stepping mechanism that has a similar operation mode to the conventional catheter navigation. A specially designed shape-memory polymer tube with water cooling structure is used to achieve variable stiffness of the catheter. Hence, four FBG sensors are attached to the catheter tip in order to monitor the tip contact force situation with temperature compensation. Experimental results show that the actuation unit is able to deliver linear and rotational motions. We have shown the feasibility of FBG force sensing to reduce the effect of temperature and detect the tip contact force. The designed catheter can change its stiffness partially, and the stiffness of the catheter can be remarkably increased in rigid state. Hence, in the rigid state, the catheter can hold its shape against a [Formula: see text] load. The prototype has also been validated with a vascular phantom, demonstrating the potential clinical value of the system. The proposed system provides important insights into the design of compact robotic-assisted catheter incorporating effective variable stiffness mechanism and real-time force sensing for intraoperative endovascular intervention.

  14. Sensing sense and mobility at the end of the life course

    Blaakilde, Anne Leonora

    2015-01-01

    is struggling with memory loss, which is impeding his life as a retired migrant. The method of embodied interaction is used in order to sense and understand his sensing of the process of mental decline. This is exemplified by three analytic perspectives: touch, embodied map, and materialised mind....... The methodology presented contributes with a focus on understanding based on sensouos theory which implies embodied interaction and an active co-construction of meaning by ethnographer as well as by reader. This chapter's discussion of a methodology that values the senses adds richness to research on the life...

  15. Final focus nomenclature

    Erickson, R.

    1986-01-01

    The formal names and common names for all devices in the final focus system of the SLC are listed. The formal names consist of a device type designator, microprocessor designator, and a four-digit unit number

  16. Final focus test beam

    1991-03-01

    This report discusses the following: the Final Focus Test Beam Project; optical design; magnets; instrumentation; magnetic measurement and BPM calibration; mechanical alignment and stabilization; vacuum system; power supplies; control system; radiation shielding and personnel protection; infrastructure; and administration

  17. Facility Focus: Food Service.

    College Planning & Management, 2002

    2002-01-01

    Describes the Hawthorn Court Community Center at Iowa State University, Ames, and the HUB-Robeson Center at Pennsylvania State University. Focuses on the food service offered in these new student-life buildings. Includes photographs. (EV)

  18. Focus group discussions

    Hennink, Monique M

    2014-01-01

    The Understanding Research series focuses on the process of writing up social research. The series is broken down into three categories: Understanding Statistics, Understanding Measurement, and Understanding Qualitative Research. The books provide researchers with guides to understanding, writing, and evaluating social research. Each volume demonstrates how research should be represented, including how to write up the methodology as well as the research findings. Each volume also reviews how to appropriately evaluate published research. Focus Group Discussions addresses the challenges associated with conducting and writing focus group research. It provides detailed guidance on the practical and theoretical considerations in conducting focus group discussions including: designing the discussion guide, recruiting participants, training a field team, moderating techniques and ethical considerations. Monique Hennink describes how a methodology section is read and evaluated by others, such as journal reviewers or ...

  19. Final focus nomenclature

    Erickson, R.

    1986-08-08

    The formal names and common names for all devices in the final focus system of the SLC are listed. The formal names consist of a device type designator, microprocessor designator, and a four-digit unit number. (LEW)

  20. Aeromagnetic Compensation Algorithm Based on Principal Component Analysis

    Peilin Wu

    2018-01-01

    Full Text Available Aeromagnetic exploration is an important exploration method in geophysics. The data is typically measured by optically pumped magnetometer mounted on an aircraft. But any aircraft produces significant levels of magnetic interference. Therefore, aeromagnetic compensation is important in aeromagnetic exploration. However, multicollinearity of the aeromagnetic compensation model degrades the performance of the compensation. To address this issue, a novel aeromagnetic compensation method based on principal component analysis is proposed. Using the algorithm, the correlation in the feature matrix is eliminated and the principal components are using to construct the hyperplane to compensate the platform-generated magnetic fields. The algorithm was tested using a helicopter, and the obtained improvement ratio is 9.86. The compensated quality is almost the same or slightly better than the ridge regression. The validity of the proposed method was experimentally demonstrated.

  1. Theoretical Study of Watershed Eco-Compensation Standards

    Yan, Dandan; Fu, Yicheng; Liu, Biu; Sha, Jinxia

    2018-01-01

    Watershed eco-compensation is an effective way to solve conflicts over water allocation and ecological destruction problems in the exploitation of water resources. Despite an increasing interest in the topic, the researches has neglected the effect of water quality and lacked systematic calculation method. In this study we reviewed and analyzed the current literature and proposedatheoretical framework to improve the calculation of co-compensation standard.Considering the perspectives of the river ecosystems, forest ecosystems and wetland ecosystems, the benefit compensation standard was determined by the input-output corresponding relationship. Based on the opportunity costs related to limiting development and water conservation loss, the eco-compensation standard was calculated.In order to eliminate the defects of eco-compensation implementation, the improvement suggestions were proposed for the compensation standard calculation and implementation.

  2. A broadband Soleil-Babinet compensator for ultrashort light pulses

    Xu, Shixiang; Ma, Yingkun; Cai, Yi; Lu, Xiaowei; Zeng, Xuanke; Chen, Hongyi; Li, Jingzhen

    2013-12-01

    This letter reports a novel design for a broadband Soleil-Babinet compensator including two pairs of optical wedges plus one plate. According to our birefringent dispersion compensation model, we can eliminate the first-order birefringent phase retardation (BPR) dispersion by using three different birefringent crystals. Our results show a Soleil-Babinet compensator based on a MgF2/ADP/KDP combination can work from 0° to 360° phase compensation with the maximal residual BPR less than 6° within the spectral region from 0.65 to 0.95 μm. The residual BPR of the compensator increases monotonically with the spectral deviation from the designed central wavelength, so our compensator is very suitable to be used for broadband laser pulses with most of their energies around the central wavelengths.

  3. A broadband Soleil–Babinet compensator for ultrashort light pulses

    Xu, Shixiang; Ma, Yingkun; Cai, Yi; Lu, Xiaowei; Zeng, Xuanke; Chen, Hongyi; Li, Jingzhen

    2013-01-01

    This letter reports a novel design for a broadband Soleil–Babinet compensator including two pairs of optical wedges plus one plate. According to our birefringent dispersion compensation model, we can eliminate the first-order birefringent phase retardation (BPR) dispersion by using three different birefringent crystals. Our results show a Soleil–Babinet compensator based on a MgF 2 /ADP/KDP combination can work from 0° to 360° phase compensation with the maximal residual BPR less than 6° within the spectral region from 0.65 to 0.95 μm. The residual BPR of the compensator increases monotonically with the spectral deviation from the designed central wavelength, so our compensator is very suitable to be used for broadband laser pulses with most of their energies around the central wavelengths. (letter)

  4. Identification of chromatin-associated regulators of MSL complex targeting in Drosophila dosage compensation.

    Erica Larschan

    Full Text Available Sex chromosome dosage compensation in Drosophila provides a model for understanding how chromatin organization can modulate coordinate gene regulation. Male Drosophila increase the transcript levels of genes on the single male X approximately two-fold to equal the gene expression in females, which have two X-chromosomes. Dosage compensation is mediated by the Male-Specific Lethal (MSL histone acetyltransferase complex. Five core components of the MSL complex were identified by genetic screens for genes that are specifically required for male viability and are dispensable for females. However, because dosage compensation must interface with the general transcriptional machinery, it is likely that identifying additional regulators that are not strictly male-specific will be key to understanding the process at a mechanistic level. Such regulators would not have been recovered from previous male-specific lethal screening strategies. Therefore, we have performed a cell culture-based, genome-wide RNAi screen to search for factors required for MSL targeting or function. Here we focus on the discovery of proteins that function to promote MSL complex recruitment to "chromatin entry sites," which are proposed to be the initial sites of MSL targeting. We find that components of the NSL (Non-specific lethal complex, and a previously unstudied zinc-finger protein, facilitate MSL targeting and display a striking enrichment at MSL entry sites. Identification of these factors provides new insight into how MSL complex establishes the specialized hyperactive chromatin required for dosage compensation in Drosophila.

  5. Compensation for Those Indirectly Affected by the Death of a Household Member

    Jędrzychowska Anna

    2017-12-01

    Full Text Available This article demonstrates the size of the budget gap that arises in a household after the death of that member who was the breadwinner of the family. It also describes how this gap can be covered by motor vehicle liability insurance. One source of funding for this gap could be, for example, an annuity for indirect victims. In many EU countries, people who are members of the household of the deceased are considered to be affected as a result of his death. Those indirectly affected will include the family members and relatives of the deceased (spouse, parent, child, sibling, and cohabitant. The person responsible for the death should pay compensation to the family members of the deceased. One of the elements determining this compensation should be the loss of income to the family of the deceased. The second element is compensation for the lost personal contribution. This paper presents the study of literature as an introduction to the relevant issues. The problem of compensation for lost income will be illustrated by legal regulations and calculations based on the account actuarial-term annuity. The study focuses on the selected EU countries. This article is part of a broader study by the author on the material consequences of personal injury and sources of their financing.

  6. Modelling Compensation Policy for Quality and Delay Deterioration in Rail Transport

    Tatiana Molkova

    2013-06-01

    Full Text Available The contribution deals with the customers’ claims on provided services during train delay in personal railway transport. There is comparison between the situation in the Czech Republic (Brno main station and Austria (Wien Westbahnhof in the contribution. Development of the compensation policy cannot be based only on customer requirements. If the railway company focuses on providing compensation for delays, it must follow its economic balance. However, as the passengers' opinion survey showed, the negative impact of delays can be reduced by providing adequate information to passengers. Based on the passengers' opinion survey, it is necessary to consider the Regulation 1371/2007/ES as the minimum of the possible and on the basis of this reasoning to compile a compensation policy. The costs associated with compensation for the delay should be divided according to the causes of the delay among the individual culprits, so that railway undertakings bear the responsibility even for delays arising from reasons that are beyond the control of the railway undertaking itself. 

  7. High harmonics focusing undulator

    Varfolomeev, A.A.; Hairetdinov, A.H.; Smirnov, A.V.; Khlebnikov, A.S. [Kurchatov Institute, Moscow (Russian Federation)

    1995-12-31

    It was shown in our previous work that there exist a possibility to enhance significantly the {open_quote}natural{close_quote} focusing properties of the hybrid undulator. Here we analyze the actual undulator configurations which could provide such field structure. Numerical simulations using 2D code PANDIRA were carried out and the enhanced focusing properties of the undulator were demonstrated. The obtained results provide the solution for the beam transport in a very long (short wavelength) undulator schemes.

  8. The Individually Focused Interview

    Clausen, Aksel Skovgaard

    2012-01-01

    relatively “strong” interviewees (interview persons: IPs) with diverse backgrounds; (2) thorough planning of the interview with well-focused themes; and (3) a thorough and repeated introduction to the interview. The omission of audio transcriptions is an obvious solution to the researcher who wants a breadth...... of range of statements stemming from the use of many more interviewees than is often possible. The Individually Focused Interview (TIFI) also provides more time for involvement in the field and further analysis....

  9. Plutonium focus area

    1996-08-01

    To ensure research and development programs focus on the most pressing environmental restoration and waste management problems at the U.S. Department of Energy (DOE), the Assistant Secretary for the Office of Environmental Management (EM) established a working group in August 1993 to implement a new approach to research and technology development. As part of this new approach, EM developed a management structure and principles that led to the creation of specific Focus Areas. These organizations were designed to focus the scientific and technical talent throughout DOE and the national scientific community on the major environmental restoration and waste management problems facing DOE. The Focus Area approach provides the framework for intersite cooperation and leveraging of resources on common problems. After the original establishment of five major Focus Areas within the Office of Technology Development (EM-50, now called the Office of Science and Technology), the Nuclear Materials Stabilization Task Group (EM-66) followed the structure already in place in EM-50 and chartered the Plutonium Focus Area (PFA). The following information outlines the scope and mission of the EM, EM-60, and EM-66 organizations as related to the PFA organizational structure

  10. Plasma focus matching conditions

    Soliman, H.M.; Masoud, M.M.; Elkhalafawy, T.A.

    1988-01-01

    A snow-plough and slug models have been used to obtain the optimum matching conditions of the plasma in the focus. The dimensions of the plasma focus device are, inner electrode radius = 2 cm, outer electrode radius = 5.5 cm, and its length = 8 cm. It was found that the maximum magnetic energy of 12.26 kJ has to be delivered to plasma focus whose density is 10 19 /cm 3 at focusing time of 2.55 μs and with total external inductance of 24.2 n H. The same method is used to evaluate the optimum matching conditions for the previous coaxial discharge system which had inner electrode radius = 1.6 cm, outer electrode radius = 3.3 cm and its length = 31.5 cm. These conditions are charging voltage = 12 kV, capacity of the condenser bank = 430 μf, plasma focus density = 10 19 /cm 3 focusing time = 8 μs and total external inductance = 60.32 n H.3 fig., 2 tab

  11. Embedding silica and polymer fibre Bragg gratings (FBG) in plastic 3D-printed sensing patches

    Zubel, Michal G.; Sugden, Kate; Webb, David J.

    2016-01-01

    This paper reports the first demonstration of a silica fibre Bragg grating (SOFBG) embedded in an FDM 3-D printed housing to yield a dual grating temperature-compensated strain sensor. We also report the first ever integration of polymer fibre Bragg grating (POFBG) within a 3-D printed sensing...

  12. Intensity-based fibre-optic sensing system using contrast modulation of subcarrier interference pattern

    Adamovsky, G.; Sherer, T. N.; Maitland, D. J.

    1989-01-01

    A novel technique to compensate for unwanted intensity losses in a fiber-optic sensing system is described. The technique involves a continuous sinusoidal modulation of the light source intensity at radio frequencies and an intensity sensor placed in an unbalanced interferometer. The system shows high sensitivity and stability.

  13. THAI-SPICE: Testbed for High-Acuity Imaging – Stable Photometry and ImageMotion Compensation Experiment

    Young, Eliot

    -borne telescopes that exhibit extremely stable temperatures through daynight cycles and, in turn, avoid optical misalignment due to temperature excursions. - Orthogonal Transfer CCDs as solid-state motion compensation devices. In order to stay within a wavefront error budget that is comparable to WFIRST or HST, a balloon-borne imaging system cannot afford a single mediocre optical element. Fine steering mirrors are especially problematic, since they are often thin, lightweight and mounted to a fastmoving mechanism. We will test the performance of OTCCDs on actual balloon platforms to assess how they can compensate for focal plane motion in flight. In addition, we will measure the photometric stability afforded by OTCCDs, and whether purposely moving a point source in a pattern can improve photometry by PSF-shaping and spreading the signal over many array elements. - In-flight wavefront error measurements. During a 100-day mission, it will be useful to monitor the focus and optical alignment of the telescope and the attached instruments. A Shack-Hartmann array located at an exit pupil will provide a detailed breakdown of the optical system: compact commercial units often provide over 15 Zernike polynomials. We want to test another method, the Curvature Wavefront Sensing method (aka, the Roddier method). The CWS method only requires images on either side of focus. It does not require extra hardware nor access to an exit pupil. We want to demonstrate the CWS method in flight and compare its results to a conventional Shack-Hartmann array. All of these projects leverage prior work, some supported by previous APRA projects, some part of NASA's ongoing GHAPS project (Gondola for High Altitude Planetary Science). We propose two domestic flights with a 24-in instrumented telescope and a gondola capable of coarse pointing. This project will involve students from the University of Virginia and the University of Colorado.

  14. Satellite Remote Sensing in Offshore Wind Energy

    Hasager, Charlotte Bay; Badger, Merete; Astrup, Poul

    2013-01-01

    Satellite remote sensing of ocean surface winds are presented with focus on wind energy applications. The history on operational and research-based satellite ocean wind mapping is briefly described for passive microwave, scatterometer and synthetic aperture radar (SAR). Currently 6 GW installed...

  15. Calcium sensing in exocytosis

    Gustavsson, Natalia; Wu, Bingbing; Han, Weiping

    2012-01-01

    an increase in intracellular calcium levels. Besides the triggering role, calcium signaling modulates the precise amount and kinetics of vesicle release. Thus, it is a central question to understand the molecular machineries responsible for calcium sensing in exocytosis. Here we provide an overview of our...... current understanding of calcium sensing in neurotransmitter release and hormone secretion....

  16. Sense and Sensibility

    Austen, Jane

    2005-01-01

    Two sisters of opposing temperament but who share the pangs of tragic love provide the subjects for Sense and Sensibility. Elinor, practical and conventional, the epitome of sense, desires a man who is promised to another woman. Marianne, emotional and sentimental, the epitome of sensibility, loses

  17. Mobile teleoperator remote sensing

    Hall, E.L.

    1986-01-01

    Sensing systems are an important element of mobile teleoperators and robots. This paper discusses certain problems and limitations of vision and other sensing systems with respect to operations in a radiological accident environment. Methods which appear promising for near-term improvements to sensor technology are described. 3 refs

  18. Deterministic Compressed Sensing

    2011-11-01

    39 4.3 Digital Communications . . . . . . . . . . . . . . . . . . . . . . . . . 40 4.4 Group Testing ...deterministic de - sign matrices. All bounds ignore the O() constants. . . . . . . . . . . 131 xvi List of Algorithms 1 Iterative Hard Thresholding Algorithm...sensing is information theoretically possible using any (2k, )-RIP sensing matrix . The following celebrated results of Candès, Romberg and Tao [54

  19. Hyperspectral remote sensing

    Eismann, Michael

    2012-01-01

    Hyperspectral remote sensing is an emerging, multidisciplinary field with diverse applications that builds on the principles of material spectroscopy, radiative transfer, imaging spectrometry, and hyperspectral data processing. This book provides a holistic treatment that captures its multidisciplinary nature, emphasizing the physical principles of hyperspectral remote sensing.

  20. Mapping sense(s) of place

    Skovse, Astrid Ravn; Hovy, Dirk; Johannsen, Anders Trærup

    2016-01-01

    , the question of how to tap into this constitutes a methodological challenge to researchers (Latham 2003, Hall 2009). This paper presents an experimental method aimed at eliciting data on sense of place and everyday mobility in a feasible and low-tech manner through the use of mental maps and mobility maps...... for answering questions about the relationship between places, speakers and linguistic practice....

  1. The Effects of Performance Measurement and Compensation on Motivation

    Marco van Herpen; C. Mirjam van Praag; Kees Cools

    2003-01-01

    This paper analyzes empirically the relationship between pay and performance. Economic and psychological theories predict that the design and implementation of a performance measurement and compensation system affect the motivation of employees. Our survey results demonstrate a positive relationship between the perceived characteristics of the complete compensation system and extrinsic motivation. Intrinsic motivation is not affected by the design of monetary compensation, but by promotion op...

  2. Adaptive Beam Loading Compensation in Room Temperature Bunching Cavities

    Edelen, J. P. [Fermilab; Chase, B. E. [Fermilab; Cullerton, E. [Fermilab; Varghese, P. [Fermilab

    2017-10-01

    In this paper we present the design, simulation, and proof of principle results of an optimization based adaptive feedforward algorithm for beam-loading compensation in a high impedance room temperature cavity. We begin with an overview of prior developments in beam loading compensation. Then we discuss different techniques for adaptive beam loading compensation and why the use of Newton?s Method is of interest for this application. This is followed by simulation and initial experimental results of this method.

  3. Essays on executive equity-based compensation and equity ownership

    Elsilä, A. (Anna)

    2015-01-01

    Abstract A major proposition of the agency theory is that the conflict of interests between an agent and a principal is reduced when the agent’s wealth and compensation are tied to the performance of the firm. Apart from the direct predicted relation to corporate performance, compensating managers with equity instruments has implications for corporate risk-taking and payout policy choices. Additionally, equity-based compensation practices are to a large extent shaped by institutional facto...

  4. Forest Ecosystem Services and Eco-Compensation Mechanisms in China

    Deng, Hongbing; Zheng, Peng; Liu, Tianxing; Liu, Xin

    2011-12-01

    Forests are a major terrestrial ecosystem providing multiple ecosystem services. However, the importance of forests is frequently underestimated from an economic perspective because of the externalities and public good properties of these services. Forest eco-compensation is a transfer mechanism that serves to internalize the externalities of forest ecosystem services by compensating individuals or companies for the losses or costs resulting from the provision of these services. China's current forest eco-compensation system is centered mainly on noncommercial forest. The primary measures associated with ecosystem services are (1) a charge on destructive activities, such as indiscriminate logging, and (2) compensation for individual or local activities and investments in forest conservation. The Compensation Fund System for Forest Ecological Benefits was first listed in the Forest Law of the People's Republic of China in 1998. In 2004, the Central Government Financial Compensation Fund, an important source for the Compensation Fund for Forest Ecological Benefits, was formally established. To improve the forest eco-compensation system, it is crucial to design and establish compensation criteria for noncommercial forests. These criteria should take both theoretical and practical concerns into account, and they should be based on the quantitative valuation of ecosystem services. Although some initial headway has been made on this task, the implementation of an effective forest eco-compensation system in China still has deficiencies and still faces problems. Implementing classification-based and dynamic management for key noncommercial forests and establishing an eco-compensation mechanism with multiple funding sources in the market economy are the key measures needed to conquer these problems and improve the forest eco-compensation system and China's forestry development in sequence.

  5. Forest ecosystem services and eco-compensation mechanisms in China.

    Deng, Hongbing; Zheng, Peng; Liu, Tianxing; Liu, Xin

    2011-12-01

    Forests are a major terrestrial ecosystem providing multiple ecosystem services. However, the importance of forests is frequently underestimated from an economic perspective because of the externalities and public good properties of these services. Forest eco-compensation is a transfer mechanism that serves to internalize the externalities of forest ecosystem services by compensating individuals or companies for the losses or costs resulting from the provision of these services. China's current forest eco-compensation system is centered mainly on noncommercial forest. The primary measures associated with ecosystem services are (1) a charge on destructive activities, such as indiscriminate logging, and (2) compensation for individual or local activities and investments in forest conservation. The Compensation Fund System for Forest Ecological Benefits was first listed in the Forest Law of the People's Republic of China in 1998. In 2004, the Central Government Financial Compensation Fund, an important source for the Compensation Fund for Forest Ecological Benefits, was formally established. To improve the forest eco-compensation system, it is crucial to design and establish compensation criteria for noncommercial forests. These criteria should take both theoretical and practical concerns into account, and they should be based on the quantitative valuation of ecosystem services. Although some initial headway has been made on this task, the implementation of an effective forest eco-compensation system in China still has deficiencies and still faces problems. Implementing classification-based and dynamic management for key noncommercial forests and establishing an eco-compensation mechanism with multiple funding sources in the market economy are the key measures needed to conquer these problems and improve the forest eco-compensation system and China's forestry development in sequence.

  6. MOTIVATION AND COMPENSATION IN HEALTH SYSTEM

    K. N. Borisov

    2015-01-01

    Full Text Available By the definition accepted by WHO, «health» it is not simple absence of an illness, but a condition of full physical, moral, mental and social wellbeing. By this definition forms of behavior and a way of life of the people, allowing prolonging the period of active, creative and happy life are meant. Health of each person – the main value for modern society. A crisis state of population as open social system, it is shown by its indignation in reply to stressful influences of negative socio-economic factors. It is accompanied by change of a condition of the public health which level refl ects depth of occurring changes. In the conditions of market managing also, the policy in the field of compensation, material encouragement and social support of medical workers essentially changes. A certain level of compensation regardless of should be guaranteed to the medical worker, whether mechanisms of economic incentives of its work are used or not. At the same time, the desire of the worker to hold a position with higher salary and desire to work on it is productive and is qualitative – far not same. Increase of material compensation not always leads to increase of labor motivation and aspiration it is better to work. Socially psychological bases of labor motivation of medical workers are those new approaches that will allow solving problems of increase of labor motivation more effectively. In article the assessment of labor motivation is analyzed by medical workers, measures for increase of labor motivation and according to improvement of quality of medical care are off ered. The majority of the western experts inefficiency of management recognize as the main problem of health care ofRussia. The conclusion that medical institutes, academies and institutes of a post degree obrazoyovaniye, professional development faculties, and, probably, and institutes an upravleyoniya, should adapt foreign experience (motivational, conceptual, technological and

  7. MOTIVATION AND COMPENSATION IN HEALTH SYSTEM

    K. N. Borisov

    2014-01-01

    Full Text Available By the defi nition accepted by WHO, «health» it is not simple absence of an illness, but a condition of full physical, moral, mental and social wellbeing. By this defi nition forms of behavior and a way of life of the people, allowing prolonging the period of active, creative and happy life are meant. Health of each person – the main value for modern society. A crisis state of population as open social system, it is shown by its indignation in reply to stressful infl uences of negative socio-economic factors. It is accompanied by change of a condition of the public health which level refl ects depth of occurring changes. In the conditions of market managing also, the policy in the fi eld of compensation, material encouragement and social support of medical workers essentially changes. A certain level of compensation regardless of should be guaranteed to the medical worker, whether mechanisms of economic incentives of its work are used or not. At the same time, the desire of the worker to hold a position with higher salary and desire to work on it is productive and is qualitative – far not same. Increase of material compensation not always leads to increase of labor motivation and aspiration it is better to work. Socially psychological bases of labor motivation of medical workers are those new approaches that will allow solving problems of increase of labor motivation more eff ectively. In article the assessment of labor motivation is analyzed by medical workers, measures for increase of labor motivation and according to improvement of quality of medical care are off ered. The majority of the western experts ineffi ciency of management recognize as the main problem of health care ofRussia. The conclusion that medical institutes, academies and institutes of a post degree obrazoyovaniye, professional development faculties, and, probably, and institutes an upravleyoniya, should adapt foreign experience (motivational, conceptual, technological

  8. A linearization time-domain CMOS smart temperature sensor using a curvature compensation oscillator.

    Chen, Chun-Chi; Chen, Hao-Wen

    2013-08-28

    This paper presents an area-efficient time-domain CMOS smart temperature sensor using a curvature compensation oscillator for linearity enhancement with a -40 to 120 °C temperature range operability. The inverter-based smart temperature sensors can substantially reduce the cost and circuit complexity of integrated temperature sensors. However, a large curvature exists on the temperature-to-time transfer curve of the inverter-based delay line and results in poor linearity of the sensor output. For cost reduction and error improvement, a temperature-to-pulse generator composed of a ring oscillator and a time amplifier was used to generate a thermal sensing pulse with a sufficient width proportional to the absolute temperature (PTAT). Then, a simple but effective on-chip curvature compensation oscillator is proposed to simultaneously count and compensate the PTAT pulse with curvature for linearization. With such a simple structure, the proposed sensor possesses an extremely small area of 0.07 mm2 in a TSMC 0.35-mm CMOS 2P4M digital process. By using an oscillator-based scheme design, the proposed sensor achieves a fine resolution of 0.045 °C without significantly increasing the circuit area. With the curvature compensation, the inaccuracy of -1.2 to 0.2 °C is achieved in an operation range of -40 to 120 °C after two-point calibration for 14 packaged chips. The power consumption is measured as 23 mW at a sample rate of 10 samples/s.

  9. Using the senses in qualitative interview research: Practical strategies

    Guillemin, M.; Harris, A.

    2014-01-01

    In the social sciences, there has been an increasing level of interest in the five senses, especially in disciplines such as anthropology, sociology, architecture and human geography. In this case study, we focus on using the senses in qualitative research interviews. We discuss a research method

  10. Synergies of multiple remote sensing data sources for REDD+ monitoring

    Sy, de V.; Herold, M.; Achard, F.; Asner, G.P.; Held, A.; Kellndorfer, J.; Verbesselt, J.

    2012-01-01

    Remote sensing technologies can provide objective, practical and cost-effective solutions for developing and maintaining REDD+ monitoring systems. This paper reviews the potential and status of available remote sensing data sources with a focus on different forest information products and synergies

  11. Remote sensing education in NASA's technology transfer program

    Weinstein, R. H.

    1981-01-01

    Remote sensing is a principal focus of NASA's technology transfer program activity with major attention to remote sensing education the Regional Program and the University Applications Program. Relevant activities over the past five years are reviewed and perspective on future directions is presented.

  12. Hydroball string sensing system

    Hurwitz, M.J.; Ekeroth, D.E.; Squarer, D.

    1991-01-01

    This patent describes a hydroball string sensing system for a nuclear reactor having a core containing a fluid at a fluid pressure. It comprises a tube connectable to the nuclear reactor so that the fluid can flow within the tube at a fluid pressure that is substantially the same as the fluid pressure of the nuclear reactor core; a hydroball string including - a string member having objects positioned therealong with a specified spacing, the object including a plurality of hydroballs, and bullet members positioned at opposing ends of the string member; first sensor means, positioned outside a first segment of the tube, for sensing one of the objects being positioned within the first segment, and for providing a sensing signal responsive to the sensing of the first sensing means

  13. A Novel Time-Varying Friction Compensation Method for Servomechanism

    Bin Feng

    2015-01-01

    Full Text Available Friction is an inevitable nonlinear phenomenon existing in servomechanisms. Friction errors often affect their motion and contour accuracies during the reverse motion. To reduce friction errors, a novel time-varying friction compensation method is proposed to solve the problem that the traditional friction compensation methods hardly deal with. This problem leads to an unsatisfactory friction compensation performance and the motion and contour accuracies cannot be maintained effectively. In this method, a trapezoidal compensation pulse is adopted to compensate for the friction errors. A generalized regression neural network algorithm is used to generate the optimal pulse amplitude function. The optimal pulse duration function and the pulse amplitude function can be established by the pulse characteristic parameter learning and then the optimal friction compensation pulse can be generated. The feasibility of friction compensation method was verified on a high-precision X-Y worktable. The experimental results indicated that the motion and contour accuracies were improved greatly with reduction of the friction errors, in different working conditions. Moreover, the overall friction compensation performance indicators were decreased by more than 54% and this friction compensation method can be implemented easily on most of servomechanisms in industry.

  14. Adaptive slope compensation for high bandwidth digital current mode controller

    Taeed, Fazel; Nymand, Morten

    2015-01-01

    An adaptive slope compensation method for digital current mode control of dc-dc converters is proposed in this paper. The compensation slope is used for stabilizing the inner current loop in peak current mode control. In this method, the compensation slope is adapted with the variations...... in converter duty cycle. The adaptive slope compensation provides optimum controller operation in term of bandwidth over wide range of operating points. In this paper operation principle of the controller is discussed. The proposed controller is implemented in an FPGA to control a 100 W buck converter...

  15. Research on the Mechanism of Cross Regional Grassland Ecological Compensation

    Yang, Ran; Ma, Jun

    2018-01-01

    In recent years, grassland environmental damage has become serious, and grassland resources protection task has become heavy, grassland ecological compensation has become an effective way to solve this problem; but the current grassland ecological compensation standards were low, the effect is poor. The fundamental reason is the model of administrative division destroys the integrity of grassland. Based on the analysis of the status quo of grassland compensation, this paper tries to protect the grassland integrity, breaks the administrative division restriction, implements the space regulation, constructs the framework of cross-regional grassland ecological compensation mechanism, describes its operation process. It provides new way to realize the sustainable development of the grassland environment.

  16. Motion compensation for structured light sensors

    Biswas, Debjani; Mertz, Christoph

    2015-05-01

    In order for structured light methods to work outside, the strong background from the sun needs to be suppressed. This can be done with bandpass filters, fast shutters, and background subtraction. In general this last method necessitates the sensor system to be stationary during data taking. The contribution of this paper is a method to compensate for the motion if the system is moving. The key idea is to use video stabilization techniques that work even if the illuminator is switched on and off from one frame to another. We used OpenCV functions and modules to implement a robust and efficient method. We evaluated it under various conditions and tested it on a moving robot outdoors. We will demonstrate that one can not only do 3D reconstruction under strong ambient light, but that it is also possible to observe optical properties of the objects in the environment.

  17. Superconductivity in compensated and uncompensated semiconductors

    Youichi Yanase and Naoyuki Yorozu

    2008-01-01

    Full Text Available We investigate the localization and superconductivity in heavily doped semiconductors. The crossover from the superconductivity in the host band to that in the impurity band is described on the basis of the disordered three-dimensional attractive Hubbard model for binary alloys. The microscopic inhomogeneity and the thermal superconducting fluctuation are taken into account using the self-consistent 1-loop order theory. The superconductor-insulator transition accompanies the crossover from the host band to the impurity band. We point out an enhancement of the critical temperature Tc around the crossover. Further localization of electron wave functions leads to the localization of Cooper pairs and induces the pseudogap. We find that both the doping compensation by additional donors and the carrier increase by additional acceptors suppress the superconductivity. A theoretical interpretation is proposed for the superconductivity in the boron-doped diamond, SiC, and Si.

  18. Background compensation for a radiation level monitor

    Keefe, D.J.

    1975-12-01

    Background compensation in a device such as a hand and foot monitor is provided by digital means using a scaler. With no radiation level test initiated, a scaler is down-counted from zero according to the background measured. With a radiation level test initiated, the scaler is up-counted from the previous down-count position according to the radiation emitted from the monitored object and an alarm is generated if, with the scaler having crossed zero in the positive going direction, a particular number is exceeded in a specific time period after initiation of the test. If the test is initiated while the scale is down-counting, the background count from the previous down- count stored in a memory is used as the initial starting point for the up-count.

  19. Considerations against a force compensated coil

    Hassenzahl, W.

    1988-08-01

    The cost of structural components in a large superconducting coil may well exceed the coil and cryostat cost. As a result, the idea of constructing a system composed of two different coil types assembled in such a way that the sources balance and reduce the total structural requirement is oft proposed. A suitable geometry has never been found for the fundamental reason that there can be no force compensated solution. In this paper, the general problem is presented and an analysis of the energy stored and stresses produced in the structure are described in a fundamental way. Finally, the relation between structural mass M and stored energy E, M ≥/rho/E/σ/sub w/, that is valid for all magnetic systems is developed, where /rho/ is the density of the structure and σ/sub w/ is the working stress in the structure. 12 refs., 2 figs

  20. Considerations against a force compensated coil

    Hassenzahl, W.

    1988-08-01

    The cost of structural components in a large superconducting coil may well exceed the coil and cryostat cost. As a result, the idea of constructing a system composed of two different coil types assembled in such a way that the forces balance and reduce the total structural requirement is oft proposed. A suitable geometry has never been found for the fundamental reason that there can be no force compensated solution. In this paper, the general problem is presented and an analysis of the energy stored and stresses produced in the structure are described in a fundamental way. Finally, the relation between structural mass M and stored energy E, M ≥ /rho/E/σ/sub w/, that is valid for all magnetic systems is developed, where /rho/ is the density of the structure and σ/sub w/ is the working stress in the structure. 8 refs., 2 figs