The thorium fuel cycle in water-moderated reactor systems

International Nuclear Information System (INIS)

Critoph, E.

1977-01-01

Current interest in the thorium cycle, as an alternative to the uranium cycle, for water-moderated reactors is based on two attractive aspects of its use - the extension of uranium resources, and the related lower sensitivity of energy costs to uranium price. While most of the scientific basis required is already available, some engineering demonstrations are needed to provide better economic data for rational decisions. Thorium and uranium cycles are compared with regard to reactor characteristics and technology, fuel-cycle technology, economic parameters, fuel-cycle costs, and system characteristics. There appear to be no major feasibility problems associated with the use of thorium, although development is required in the areas of fuel testing and fuel management. The use of thorium cycles implies recycling the fuel, and the major uncertainties are in the associated costs. Experience in the design and operation of fuel reprocessing and active-fabrication facilities is required to estimate costs to the accuracy needed for adequately defining the range of conditions economically favourable to thorium cycles. In heavy-water reactors (HWRs) thorium cycles having uranium requirements at equilibrium ranging from zero to a quarter of those for the natural-uranium once-through cycle appear feasible. An ''inventory'' of uranium of between 1 and 2Mg/MW(e) is required for the transition to equilibrium. The cycles with the lowest uranium requirements compete with the others only at high uranium prices. Using thorium in light-water reactors, uranium requirements can be reduced by a factor of between two and three from the once-through uranium cycle. The light-water breeder reactor, promising zero uranium requirements at equilibrium, is being developed. Larger uranium inventories are required than for the HWRs. The lead time, from a decision to use thorium to significant impact on uranium utilization (compared to uranium cycle, recycling plutonium), is some two decades

Use of thorium for high temperature gas-cooled reactors

Energy Technology Data Exchange (ETDEWEB)

Guimarães, Cláudio Q., E-mail: claudio_guimaraes@usp.br [Universidade de São Paulo (USP), SP (Brazil). Instituto de Física; Stefani, Giovanni L. de, E-mail: giovanni.stefani@ipen.br [Instituto de Pesquisas Energéticas e Nucleares (IPEN/CNEN-SP), São Paulo, SP (Brazil); Santos, Thiago A. dos, E-mail: thiago.santos@ufabc.edu.br [Universidade Federal do ABC (UFABC), Santo André, SP (Brazil)

2017-07-01

The HTGR ( High Temperature Gas-cooled Reactor) is a 4{sup th} generation nuclear reactor and is fuelled by a mixture of graphite and fuel-bearing microspheres. There are two competitive designs of this reactor type: The German “pebble bed” mode, which is a system that uses spherical fuel elements, containing a graphite-and-fuel mixture coated in a graphite shell; and the American version, whose fuel is loaded into precisely located graphite hexagonal prisms that interlock to create the core of the vessel. In both variants, the coolant consists of helium pressurised. The HTGR system operates most efficiently with the thorium fuel cycle, however, so relatively little development has been carried out in this country on that cycle for HTGRs. In the Nuclear Engineering Centre of IPEN (Instituto de Pesquisas Energéticas e Nucleares), a study group is being formed linked to thorium reactors, whose proposal is to investigate reactors using thorium for {sup 233}U production and rejects burning. The present work intends to show the use of thorium in HTGRs, their advantages and disadvantages and its feasibility. (author)

Thorium-based Molten Salt Reactor (TMSR) project in China

International Nuclear Information System (INIS)

Dai, Zhimin; Liu, Wei

2013-01-01

Making great efforts in development of nuclear energy is one of the long-term-plan in China's energy strategies. The advantages of Thorium-based nuclear energy are: rich resource in nature, less nuclear waste, low toxicity, nuclear non-proliferation and so on. Furthermore, China is a country with abundant thorium, thus it is necessary to develop the Thorium-based Molten Salt Reactor (TMSR) in China. Shanghai Institute of Applied Physics, Chinese Academy of Sciences (SINAP) had designed and constructed the first China's light-water reactor and developed a zero-power thorium-based molten salt reactor successfully in the early 1970s. The applied research project 'thorium molten salt reactor nuclear power system' by SINAP together with several other institutes had been accepted and granted by China government in 2011. The whole project has been divided into three stages: Firstly, built a 2 MW-zero-power high temperature solid molten salt reactor in 2015 and a 2 MW-zero-power high temperature liquid molten salt reactor in 2017. Secondly, in 2020 built a 10 MW high temperature liquid molten salt reactor. Thirdly, on the base of previous work, a 100 MW high temperature molten salt reactor should be achieving in 2030. After more than one years of efforts, a high quality scientific research team has been formed, which is able to design the molten salt reactor, the molten salt loop and related key equipment, the systems of molten salt preparation, purification and the radioactive gas removal. In the past one year, the initial physical design of high temperature molten salt reactor has been completed; the nuclear chemistry and radiation chemical laboratory has been built, a high temperature salt (HTS) loop and radioactive gas removal experiment device system have been successfully developed and constructed. Further, the preliminary study on reactor used carbon-carbon composite material has been investigated. (author)

The thorium fuel cycle in water-moderated reactor systems

International Nuclear Information System (INIS)

Critoph, E.

1977-05-01

Thorium and uranium cycles are compared with regard to reactor characteristics and technology, fuel-cycle technology, economic parameters, fuel-cycle costs, and system characteristics. In heavy-water reactors (HWRs) thorium cycles having uranium requirements at equilibrium ranging from zero to a quarter of those for the natural-uranium once-through cycle appear feasible. An 'inventory' of uranium of between 1 and 2 Mg/MW(e) is required for the transition to equilibrium. The cycles with the lowest uranium requirements compete with the others only at high uranium prices. Using thorium in light-water reactors, uranium requirements can be reduced by a factor of between two and three from the once-through uranium cycle. The light-water breeder reactor, promising zero uranium requirements at equilibrium, is being developed. Larger uranium inventories are required than for the HWRs. The lead time, from a decision to use thorium to significant impact on uranium utilization (compared to uranium cycle, recycling plutonium) is some two decades

A survey of thorium utilization in thermal power reactors

International Nuclear Information System (INIS)

Oosterkamp, W.J.

1974-01-01

The present status of thorium utilization in thermal reactors HTGR's, HWR's and LWR's has been reviewed. Physics considerations are made to obtain the optimum use of thorium. Existing information on reprocessing and refabrication is given together with the properties of thorium metal and thoria

A proposal for rational thorium utilization: thorims-nes

International Nuclear Information System (INIS)

Kurukawa, K.; Erbay, L. B.

1997-01-01

In this study, a globally applicable system depending on a new philosophy has been introduced for solving the problems connected with nuclear safety, ratio-waste, anti-nuclear proliferation and terrorism and public/institutional acceptance and economy. This rational thorium breeding fuel-cycle system named as THORIMS-NES (Thorium Molten- Salt Nuclear Energy Synergetics ) appears to be particularly promising and can be the way of nuclear power development. THORIMS-NES depends on three principles: I. Thorium utilization, II. Application of molten-fluoride fuel technology and III. Separation of fissile producing breeders and power producing reactors. Thorium fuel cycle has benefit on the reduction of trans-U elements and for recycling fuels produced by all kinds of military, research and industrial reactors. A system for the realization of THORIMS-NES has been introduced by the explanation of connections/relations between facilities. In this study, the status of countries/groups working on Th and Th fuel cycle has been summarized. Additionally, the resultant announcement of the International Conference on Thorium Molten Salt Reactor Development (8-11 April, 1997, Santa Monica) has been mentioned to present the cooperation of scientists and engineers for the realization of THORIMS-NES

Fast Thorium Molten Salt Reactors Started with Plutonium

International Nuclear Information System (INIS)

Merle-Lucotte, E.; Heuer, D.; Le Brun, C.; Brissot, R.; Liatard, E.; Meplan, O.; Nuttin, A.; Mathieu, L.

2006-01-01

One of the pending questions concerning Molten Salt Reactors based on the 232 Th/ 233 U fuel cycle is the supply of the fissile matter, and as a consequence the deployment possibilities of a fleet of Molten Salt Reactors, since 233 U does not exist on earth and is not yet produced in the current operating reactors. A solution may consist in producing 233 U in special devices containing Thorium, in Pressurized Water or Fast Neutrons Reactors. Two alternatives to produce 233 U are examined here: directly in standard Molten Salt Reactors started with Plutonium as fissile matter and then operated in the Th/ 233 U cycle; or in dedicated Molten Salt Reactors started and fed with Plutonium as fissile matter and Thorium as fertile matter. The idea is to design a critical reactor able to burn the Plutonium and the minor actinides presently produced in PWRs, and consequently to convert this Plutonium into 233 U. A particular reactor configuration is used, called 'unique channel' configuration in which there is no moderator in the core, leading to a quasi fast neutron spectrum, allowing Plutonium to be used as fissile matter. The conversion capacities of such Molten Salt Reactors are excellent. For Molten Salt Reactors only started with Plutonium, the assets of the Thorium fuel cycle turn out to be quickly recovered and the reactor's characteristics turn out to be equivalent to Molten Salt Reactors operated with 233 U only. Using a combination of Molten Salt Reactors started or operated with Plutonium and of Molten Salt Reactors started with 233 U, the deployment capabilities of these reactors fully satisfy the condition of sustainability. (authors)

Thorium Fuel Performance in a Tight-Pitch Light Water Reactor Lattice

International Nuclear Information System (INIS)

Kim, Taek Kyum; Downar, Thomas J.

2002-01-01

Research on the utilization of thorium-based fuels in the intermediate neutron spectrum of a tight-pitch light water reactor (LWR) lattice is reported. The analysis was performed using the Studsvik/Scandpower lattice physics code HELIOS. The results show that thorium-based fuels in the intermediate spectrum of tight-pitch LWRs have considerable advantages in terms of conversion ratio, reactivity control, nonproliferation characteristics, and a reduced production of long-lived radiotoxic wastes. Because of the high conversion ratio of thorium-based fuels in intermediate spectrum reactors, the total fissile inventory required to achieve a given fuel burnup is only 11 to 17% higher than that of 238 U fertile fuels. However, unlike 238 U fertile fuels, the void reactivity coefficient with thorium-based fuels is negative in an intermediate spectrum reactor. This provides motivation for replacing 238 U with 232 Th in advanced high-conversion intermediate spectrum LWRs, such as the reduced-moderator reactor or the supercritical reactor

Thorium cycle and molten salt reactors: field parameters and field constraints investigations toward 'thorium molten salt reactor' definition

International Nuclear Information System (INIS)

Mathieu, L.

2005-09-01

Producing nuclear energy in order to reduce the anthropic CO 2 emission requires major technological advances. Nuclear plants of 4. generation have to respond to several constraints, as safety improvements, fuel breeding and radioactive waste minimization. For this purpose, it seems promising to use Thorium Cycle in Molten Salt Reactors. Studies on this domain have already been carried out. However, the final concept suffered from serious issues and was discontinued. A new reflection on this topic is being led in order to find acceptable solutions, and to design the Thorium Molten Salt Reactor concept. A nuclear reactor is simulated by the coupling of a neutron transport code with a materials evolution code. This allows us to reproduce the reactor behavior and its evolution all along its operation. Thanks to this method, we have studied a large number of reactor configurations. We have evaluated their efficiency through a group of constraints they have to satisfy. This work leads us to a better understanding of many physical phenomena controlling the reactor behavior. As a consequence, several efficient configurations have been discovered, allowing the emergence of new points of view in the research of Molten Salt Reactors. (author)

Use of thorium in the generation IV Molten Salt reactors and perspectives for Brazil

International Nuclear Information System (INIS)

Seneda, Jose A.; Lainetti, Paulo E.O.

2013-01-01

Interest in thorium stems mainly from the fact that it is expected a substantial increase in uranium prices over the next fifty years. The reactors currently in operation consume 65,500 tons of uranium per year. Each electrical gigawatt (GWe) additional need about 200 tU mined per year. So advanced fuel cycles, which increase the reserves of nuclear materials are interesting, particularly the use of thorium to produce the fissile isotope 233 U. It is important to mention some thorium advantages. Thorium is three to five times more abundant than uranium in the earth's crust. Thorium has only one oxidation state. Additionally, thoria produces less radiotoxicity than the UO 2 because it produces fewer amounts of actinides, reducing the radiotoxicity of long life nuclear waste. ThO 2 has higher corrosion resistance than UO 2 , besides being chemically stable due to their low water solubility. The burning of Pu in a reactor based in thorium also decreases the inventories of Pu from the current fuel cycles, resulting in lower risks of material diversion for use in nuclear weapons. There are some ongoing projects in the world, taking into consideration the proposed goals for Generation IV reactors, namely: sustainability, economics, safety and reliability, proliferation resistance and physical protection. Some developments on the use of thorium in reactors are underway, with the support of the IAEA and some governs. Can be highlighted some reactor concepts using thorium as fuel: CANDU; ADTR -Accelerator Driven Thorium Reactor; AHWR -Advanced Heavy Water Reactor proposed by India (light water cooled and moderated by heavy water) and the MSR -Molten Salt Reactor. The latter is based on a reactor concept that has already been successfully tested in the U.S. in the 50s, for use in aircrafts. In this paper, we discuss the future importance of thorium, particularly for Brazil, which has large mineral reserves of this strategic element, the characteristics of the molten salt

Use of thorium in the generation IV Molten Salt reactors and perspectives for Brazil

Energy Technology Data Exchange (ETDEWEB)

Seneda, Jose A.; Lainetti, Paulo E.O., E-mail: jaseneda@ipen.br [Instituto de Pesquisas Energeticas e Nucleares (IPEN/CNEN-SP), Sao Paulo, SP (Brazil)

2013-07-01

Interest in thorium stems mainly from the fact that it is expected a substantial increase in uranium prices over the next fifty years. The reactors currently in operation consume 65,500 tons of uranium per year. Each electrical gigawatt (GWe) additional need about 200 tU mined per year. So advanced fuel cycles, which increase the reserves of nuclear materials are interesting, particularly the use of thorium to produce the fissile isotope {sup 233}U. It is important to mention some thorium advantages. Thorium is three to five times more abundant than uranium in the earth's crust. Thorium has only one oxidation state. Additionally, thoria produces less radiotoxicity than the UO{sub 2} because it produces fewer amounts of actinides, reducing the radiotoxicity of long life nuclear waste. ThO{sub 2} has higher corrosion resistance than UO{sub 2}, besides being chemically stable due to their low water solubility. The burning of Pu in a reactor based in thorium also decreases the inventories of Pu from the current fuel cycles, resulting in lower risks of material diversion for use in nuclear weapons. There are some ongoing projects in the world, taking into consideration the proposed goals for Generation IV reactors, namely: sustainability, economics, safety and reliability, proliferation resistance and physical protection. Some developments on the use of thorium in reactors are underway, with the support of the IAEA and some governs. Can be highlighted some reactor concepts using thorium as fuel: CANDU; ADTR -Accelerator Driven Thorium Reactor; AHWR -Advanced Heavy Water Reactor proposed by India (light water cooled and moderated by heavy water) and the MSR -Molten Salt Reactor. The latter is based on a reactor concept that has already been successfully tested in the U.S. in the 50s, for use in aircrafts. In this paper, we discuss the future importance of thorium, particularly for Brazil, which has large mineral reserves of this strategic element, the

Mechanical structure and problem of thorium molten salt reactor

International Nuclear Information System (INIS)

Kamei, Takashi

2011-01-01

After Fukushima Daiichi accident, there became great interest in Thorium Molten Salt Reactor (MSR) for the safety as station blackout leading to auto drainage of molten salts with freeze valve. This article described mechanical structure of MSR and problems of materials and pipes. Material corrosion problem by molten salts would be solved using modified Hastelloy N with Ti and Nb added, which should be confirmed by operation of an experimental reactor. Trends in international activities of MSR were also referred including China declaring MSR development in January 2011 to solve thorium contamination issues at rare earth production and India rich in thorium resources. (T. Tanaka)

Status of thorium technology

International Nuclear Information System (INIS)

Garg, R.K.; Raghavan, R.V.; Karve, V.M.; Narayandas, G.R.

1977-01-01

Although a number of studies have been conducted in various countries to evolve reactor systems based on thorium fuel cycle, its use, so far, is limited to only a few reactors. However, for countries having large reserves of thorium, its utilization is of great significance for their nuclear power programmes. Reasonably assured world resources of thorium in the lower price range have been estimated at more than 500,000 tons of ThO 2 . While most of these resources are in placer deposits in various parts of the world, some vein deposits and uranium ores are other important sources of thorium. Monazite, the most important mineral of thorium, is found in the beach sand deposits along with other heavy minerals like ilmenite, rutile, zircon, and sillimanite etc. Mining of these deposits is usually carried out by suction dredging and separation of monazite from other minerals is effected by a combination of magnetic, electrostatic and gravity separation techniques. Chemical processing of monazite is carried out either by sulphuric acid or caustic treatment, followed by separation of the rare earths and thorium by partial precipitation or leaching. The thorium concentrate is further processed to obtain mantle grade thorium nitrate by chemical purification steps whereas solvent extraction using TBP is adopted for making nuclear-grade material. The purified thorium nitrate is converted to the oxide usually by precipitation as oxalate followed by calcination. The oxide is reduced directly with calcium or converted to the chloride or fluoride and then reduced by calcium or magnesium to obtain thorium metal. Various fuel designs based on the metal or its alloys, mixed oxides or carbides, and dispersed type fuel elements have been developed and accordingly, different fabrication techniques have been employed. Work on irradiation of thorium containing fuel elements and separation of U 233 is being carried out. This paper reviews the status of thorium technology in the world with

Evaluation of plutonium, uranium, and thorium use in power reactor fuel cycles

International Nuclear Information System (INIS)

Kasten, P.R.; Homan, F.J.

1977-01-01

The increased cost of uranium and separative work has increased the attractiveness of plutonium use in both uranium and thorium fuel cycles in thermal reactors. A technology, fuel utilization, and economic evaluation is given for uranium and thorium fuel cycles in various reactor types, along with the use of plutonium and 238 U. Reactors considered are LWRs, HWRs, LWBRs, HTGRs, and FBRs. Key technology factors are fuel irradiation performance and associated physical property values. Key economic factors are unit costs for fuel fabrication and reprocessing, and for refabrication of recycle fuels; consistent cost estimates are utilized. In thermal reactors, the irradiation performance of ceramic fuels appears to be satisfactory. At present costs for uranium ore and separative work, recycle of plutonium with thorium rather than uranium is preferable from fuel utilization and economic viewpoints. Further, the unit recovery cost of plutonium is lower from LWR fuels than from natural-uranium HWR fuels; use of LWR product permits plutonium/thorium fueling to compete with uranium cycles. Converting uranium cycles to thorium cycles increases the energy which can be extracted from a given uranium resource. Thus, additional fuel utilization improvement can be obtained by fueling all thermal reactors with thorium, but this requires use of highly enriched uranium; use of 235 U with thorium is most economic in HTGRs followed by HWRs and then LWRs. Marked improvement in long-term fuel utilization can be obtained through high thorium loadings and short fuel cycle irradiations as in the LWBR, but this imposes significant economic penalties. Similar operating modes are possible in HWRs and HTGRs. In fast reactors, use of the plutonium-uranium cycle gives advantageous fuel resource utilization in both LMFBRs and GCFRs; use of the thorium cycle provides more negative core reactivity coefficients and more flexibility relative to use of recycle fuels containing uranium of less than 20

Economics and utilization of thorium in nuclear reactors

International Nuclear Information System (INIS)

1978-05-01

Information on thorium utilization in power reactors is presented concerning the potential demand for nuclear power, the potential supply for nuclear power, economic performance of thorium under different recycle policies, ease of commercialization of the economically preferred cases, policy options to overcome institutional barriers, and policy options to overcome technological and regulatory barriers

Thorium in heavy water reactors

International Nuclear Information System (INIS)

Andersson, G.

1984-12-01

Advanced heavy water reactors can provide energy on a global scale beyond the foreseeable future. Their economic and safety features are promising: 1. The theoretical feasibility of the Self Sufficient Equilibrium Thorium (SSET) concept is confirmed by new calculations. Calculations show that the adjuster rod geometry used in natural uranium CANDU reactors is adequate also for SSET if the absorption in the rods is graded. 2. New fuel bundle designs can permit substantially higher power output from a CANDU reactor. The capital cost for fuel, heavy water and mechanical equipment can thereby be greatly reduced. Progress is possible with the traditional fuel material oxide, but the use of thorium metal gives much larger effects. 3. A promising long range possibility is to use pressure tanks instead of pressure tubes. Heat removal from the core is facilitated. Negative temperature and void coefficients provide inherent safety features. Refuelling under power is no longer needed if control by moderator displacement is used. Reduced quality demand on the fuel permits lower fuel costs. The neutron economy is improved by the absence of pressure and clandria tubes and also by the use of radial and axial blankets. A modular seed blanket design can reduce the Pa losses. The experience from construction of tank designs is good e.g. AAgesta, Attucha. It is now also possible to utilize technology from LWR reactors and the implementation of advanced heavy water reactors would thus be easier than HTR or LMFBR systems. (Author)

Self-Sustaining Thorium Boiling Water Reactors

International Nuclear Information System (INIS)

Greenspan, Ehud; Gorman, Phillip M.; Bogetic, Sandra; Seifried, Jeffrey E.; Zhang, Guanheng; Varela, Christopher R.; Fratoni, Massimiliano; Vijic, Jasmina J.; Downar, Thomas; Hall, Andrew; Ward, Andrew; Jarrett, Michael; Wysocki, Aaron; Xu, Yunlin; Kazimi, Mujid; Shirvan, Koroush; Mieloszyk, Alexander; Todosow, Michael; Brown, Nicolas; Cheng, Lap

2015-01-01

The primary objectives of this project are to: Perform a pre-conceptual design of a core for an alternative to the Hitachi proposed fuel-self- sustaining RBWR-AC, to be referred to as a RBWR-Th. The use of thorium fuel is expected to assure negative void coefficient of reactivity (versus positive of the RBWR-AC) and improve reactor safety; Perform a pre-conceptual design of an alternative core to the Hitachi proposed LWR TRU transmuting RBWR-TB2, to be referred to as the RBWR-TR. In addition to improved safety, use of thorium for the fertile fuel is expected to improve the TRU transmutation effectiveness; Compare the RBWR-Th and RBWR-TR performance against that of the Hitachi RBWR core designs and sodium cooled fast reactor counterparts - the ARR and ABR; and, Perform a viability assessment of the thorium-based RBWR design concepts to be identified along with their associated fuel cycle, a technology gap analysis, and a technology development roadmap. A description of the work performed and of the results obtained is provided in this Overview Report and, in more detail, in the Attachments. The major findings of the study are summarized.

Self-Sustaining Thorium Boiling Water Reactors

Energy Technology Data Exchange (ETDEWEB)

Greenspan, Ehud [Univ. of California, Berkeley, CA (United States); Gorman, Phillip M. [Univ. of California, Berkeley, CA (United States); Bogetic, Sandra [Univ. of California, Berkeley, CA (United States); Seifried, Jeffrey E. [Univ. of California, Berkeley, CA (United States); Zhang, Guanheng [Univ. of California, Berkeley, CA (United States); Varela, Christopher R. [Univ. of California, Berkeley, CA (United States); Fratoni, Massimiliano [Univ. of California, Berkeley, CA (United States); Vijic, Jasmina J. [Univ. of California, Berkeley, CA (United States); Downar, Thomas [Univ. of Michigan, Ann Arbor, MI (United States); Hall, Andrew [Univ. of Michigan, Ann Arbor, MI (United States); Ward, Andrew [Univ. of Michigan, Ann Arbor, MI (United States); Jarrett, Michael [Univ. of Michigan, Ann Arbor, MI (United States); Wysocki, Aaron [Univ. of Michigan, Ann Arbor, MI (United States); Xu, Yunlin [Univ. of Michigan, Ann Arbor, MI (United States); Kazimi, Mujid [Massachusetts Inst. of Technology (MIT), Cambridge, MA (United States); Shirvan, Koroush [Massachusetts Inst. of Technology (MIT), Cambridge, MA (United States); Mieloszyk, Alexander [Massachusetts Inst. of Technology (MIT), Cambridge, MA (United States); Todosow, Michael [Brookhaven National Lab. (BNL), Upton, NY (United States); Brown, Nicolas [Brookhaven National Lab. (BNL), Upton, NY (United States); Cheng, Lap [Brookhaven National Lab. (BNL), Upton, NY (United States)

2015-03-15

The primary objectives of this project are to: Perform a pre-conceptual design of a core for an alternative to the Hitachi proposed fuel-self- sustaining RBWR-AC, to be referred to as a RBWR-Th. The use of thorium fuel is expected to assure negative void coefficient of reactivity (versus positive of the RBWR-AC) and improve reactor safety; Perform a pre-conceptual design of an alternative core to the Hitachi proposed LWR TRU transmuting RBWR-TB2, to be referred to as the RBWR-TR. In addition to improved safety, use of thorium for the fertile fuel is expected to improve the TRU transmutation effectiveness; Compare the RBWR-Th and RBWR-TR performance against that of the Hitachi RBWR core designs and sodium cooled fast reactor counterparts - the ARR and ABR; and, Perform a viability assessment of the thorium-based RBWR design concepts to be identified along with their associated fuel cycle, a technology gap analysis, and a technology development roadmap. A description of the work performed and of the results obtained is provided in this Overview Report and, in more detail, in the Attachments. The major findings of the study are summarized.

Operation of CANDU power reactor in thorium self-sufficient fuel cycle

Indian Academy of Sciences (India)

This paper presents the results of calculations for CANDU reactor operation in thorium fuel cycle. Calculations are performed to estimate the feasibility of operation of heavy-water thermal neutron power reactor in self-sufficient thorium cycle. Parameters of active core and scheme of fuel reloading were considered to be the ...

Core Design and Deployment Strategy of Heavy Water Cooled Sustainable Thorium Reactor

Directory of Open Access Journals (Sweden)

Naoyuki Takaki

2012-08-01

Full Text Available Our previous studies on water cooled thorium breeder reactor based on matured pressurized water reactor (PWR plant technology concluded that reduced moderated core by arranging fuel pins in a triangular tight lattice array and using heavy water as coolant is appropriate for achieving better breeding performance and higher burn-up simultaneously [1–6]. One optimum core that produces 3.5 GW thermal energy using Th-²³³U oxide fuel shows a breeding ratio of 1.07 and averaged burn-up of about 80 GWd/t with long cycle length of 1300 days. The moderator to fuel volume ratio is 0.6 and required enrichment of ²³³U for the fresh fuel is about 7%. The coolant reactivity coefficient is negative during all cycles despite it being a large scale breeder reactor. In order to introduce this sustainable thorium reactor, three-step deployment scenario, with intermediate transition phase between current light water reactor (LWR phase and future sustainer phase, is proposed. Both in transition phase and sustainer phase, almost the same core design can be applicable only by changing fissile materials mixed with thorium from plutonium to ²³³U with slight modification in the fuel assembly design. Assuming total capacity of 60 GWe in current LWR phase and reprocessing capacity of 800 ton/y with further extensions to 1600 ton/y, all LWRs will be replaced by heavy water cooled thorium reactors within about one century then thorium reactors will be kept operational owing to its potential to sustain fissile fuels while reprocessing all spent fuels until exhaustion of massive thorium resource.

Partial thorium loading in the initial core of Kakrapar atomic power reactor

International Nuclear Information System (INIS)

Balakrishnan, M.R.

1993-01-01

The first unit of Kakrapar nuclear power station has gone critical with some thorium oxide fuel bundles loaded in its core. The thorium helps to flatten the power by reducing neutron flux in the centre of the reactor. However, the placing of the thorium had to be planned with care, because if the neutron flux at a point where a safety rod is located is depressed, the reactivity worth of the safety rod gets reduced. Using a dynamic programing approach, the Reactor Engineering Division of Bhabha Atomic Research Centre worked out a satisfactory configuration for loading the thorium bundles

Feasibility study and economic analysis on thorium utilization in heavy water reactors

International Nuclear Information System (INIS)

1978-07-01

Even though natural uranium is a more easily usable fuel in heavy water reactors, thorium fuel cycles have also been considered owing to certain attractive features of the thorium fuel cycle in heavy water reactors. The relatively higher fission neutron yield per thermal neutron absorption in 233 U combined with the very low neutron absorption cross section of heavy water make it possible to achieve breeding in a heavy water reactor operating on Th- 233 U fuel cycle. Even if the breeding ratio is very low, once a self-sustaining cycle is achieved, thereafter dependence on uranium can be completely eliminated. Thus, with a self-sustaining Th- 233 U fuel cycle in heavy water reactors, a given quantity of natural uranium will be capable of supporting a much larger installed generating capacity to significantly longer period of time. However, since thorium does not contain any fissile isotope, fissile material has to be added at the beginning. Concentrated fissile material is considerably more expensive than the 235 U contained in natural uranium. This makes the fuel cycle cost higher with thorium fuel cycle, at least during the initial stages. The situation is made worse by the fact that, because of its higher thermal neutron absorption cross section, thorium requires a higher concentration of fissile material than 238 U. Nevertheless, because of the superior nuclear characteristics of 233 U, once uranium becomes more expensive, thorium fuel cycle in heavy water reactors may become economically acceptable. Furthermore, the energy that can be made available from a given quantity of uranium is considerably increased with a self-sustaining thorium fuel cycle

Analysis on small long life reactor using thorium fuel for water cooled and metal cooled reactor types

International Nuclear Information System (INIS)

Permana, Sidik

2009-01-01

Long-life reactor operation can be adopted for some special purposes which have been proposed by IAEA as the small and medium reactor (SMR) program. Thermal reactor and fast reactor types can be used for SMR and in addition to that program the utilization of thorium fuel as one of the candidate as a 'partner' fuel with uranium fuel which can be considered for optimizing the nuclear fuel utilization as well as recycling spent fuel. Fissile U-233 as the main fissile material for thorium fuel shows higher eta-value for wider energy range compared with other fissile materials of U-235 and Pu-239. However, it less than Pu-239 for fast energy region, but it still shows high eta-value. This eta-value gives the reactor has higher capability for obtaining breeding condition or high conversion capability. In the present study, the comparative analysis on small long life reactor fueled by thorium for different reactor types (water cooled and metal cooled reactor types). Light water and heavy water have been used as representative of water-cooled reactor types, and for liquid metal-cooled reactor types, sodium-cooled and lead-bismuth-cooled have been adopted. Core blanket arrangement as general design configuration, has been adopted which consist of inner blanket region fueled by thorium oxide, and two core regions (inner and out regions) fueled by fissile U-233 and thorium oxide with different percentages of fissile content. SRAC-CITATION and JENDL-33 have been used as core optimization analysis and nuclear data library for this analysis. Reactor operation time can reaches more than 10 years operation without refueling and shuffling for different reactor types and several power outputs. As can be expected, liquid metal cooled reactor types can be used more effective for obtaining long life reactor with higher burnup, higher power density, higher breeding capability and lower excess reactivity compared with water-cooled reactors. Water cooled obtains long life core operation

Once-through thorium cycles in Candu reactors

International Nuclear Information System (INIS)

Milgram, M.S.

1982-01-01

In once-through thorium cycles pure thorium fuel bundles can be irradiated conjointly with uranium fuel bundles in a CANDU reactor with parameters judiciously chosen such that the overall fuel cycle cost is competitive with other possibilities - notably low-enriched uranium. Uranium 233 can be created and stockpiled for possible future use with no imperative that it be used unless future conditions warrant, and a stockpile can be begun independently of the state of reprocessing technology. The existence and general properties of these cycles are discussed

Fuel-management simulations for once-through thorium fuel cycle in CANDU reactors

International Nuclear Information System (INIS)

Chan, P.S.W.; Boczar, P.G.; Ellis, R.J.; Ardeshiri, F.

1999-01-01

High neutron economy, on-power refuelling and a simple fuel bundle design result in unsurpassed fuel cycle flexibility for CANDU reactors. These features facilitate the introduction and exploitation of thorium fuel cycles in existing CANDU reactors in an evolutionary fashion. Detailed full-core fuel-management simulations concluded that a once-through thorium fuel cycle can be successfully implemented in an existing CANDU reactor without requiring major modifications. (author)

Thorium cycle and molten salt reactors: field parameters and field constraints investigations toward 'thorium molten salt reactor' definition; Cycle thorium et reacteurs a sel fondu: exploration du champ des parametres et des contraintes definissant le 'Thorium Molten Salt Reactor'

Energy Technology Data Exchange (ETDEWEB)

Mathieu, L

2005-09-15

Producing nuclear energy in order to reduce the anthropic CO{sub 2} emission requires major technological advances. Nuclear plants of 4. generation have to respond to several constraints, as safety improvements, fuel breeding and radioactive waste minimization. For this purpose, it seems promising to use Thorium Cycle in Molten Salt Reactors. Studies on this domain have already been carried out. However, the final concept suffered from serious issues and was discontinued. A new reflection on this topic is being led in order to find acceptable solutions, and to design the Thorium Molten Salt Reactor concept. A nuclear reactor is simulated by the coupling of a neutron transport code with a materials evolution code. This allows us to reproduce the reactor behavior and its evolution all along its operation. Thanks to this method, we have studied a large number of reactor configurations. We have evaluated their efficiency through a group of constraints they have to satisfy. This work leads us to a better understanding of many physical phenomena controlling the reactor behavior. As a consequence, several efficient configurations have been discovered, allowing the emergence of new points of view in the research of Molten Salt Reactors. (author)

Gas-Cooled Thorium Reactor with Fuel Block of the Unified Design

Directory of Open Access Journals (Sweden)

Igor Shamanin

2015-01-01

Full Text Available Scientific researches of new technological platform realization carried out in Russia are based on ideas of nuclear fuel breeding in closed fuel cycle and physical principles of fast neutron reactors. Innovative projects of low-power reactor systems correspond to the new technological platform. High-temperature gas-cooled thorium reactors with good transportability properties, small installation time, and operation without overloading for a long time are considered perspective. Such small modular reactor systems at good commercial, competitive level are capable of creating the basis of the regional power industry of the Russian Federation. The analysis of information about application of thorium as fuel in reactor systems and its perspective use is presented in the work. The results of the first stage of neutron-physical researches of a 3D model of the high-temperature gas-cooled thorium reactor based on the fuel block of the unified design are given. The calculation 3D model for the program code of MCU-5 series was developed. According to the comparison results of neutron-physical characteristics, several optimum reactor core compositions were chosen. The results of calculations of the reactivity margins, neutron flux distribution, and power density in the reactor core for the chosen core compositions are presented in the work.

Inhalation radiotoxicity of irradiated thorium as a heavy water reactor fuel

International Nuclear Information System (INIS)

Edwards, G.W.R.; Priest, N.D.; Richardson, R.B.

2013-01-01

The online refueling capability of Heavy Water Reactors (HWRs), and their good neutron economy, allows a relatively high amount of neutron absorption in breeding materials to occur during normal fuel irradiation. This characteristic makes HWRs uniquely suited to the extraction of energy from thorium. In Canada, the toxicity and radiological protection methods dealing with personnel exposure to natural uranium (NU) spent fuel (SF) are well-established, but the corresponding methods for irradiated thorium fuel are not well known. This study uses software to compare the activity and toxicity of irradiated thorium fuel ('thorium SF') against those of NU. Thorium elements, contained in the inner eight elements of a heterogeneous high-burnup bundle having LEU (Low-enriched uranium) in the outer 35 elements, achieve a similar burnup to NU SF during its residence in a reactor, and the radiotoxicity due to fission products was found to be similar. However, due to the creation of such inhalation hazards as U-232 and Th-228, the radiotoxicity of thorium SF was almost double that of NU SF after sufficient time has passed for the decay of shorter-lived fission products. Current radio-protection methods for NU SF exposure are likely inadequate to estimate the internal dose to personnel to thorium SF, and an analysis of thorium in fecal samples is recommended to assess the internal dose from exposure to this fuel. (authors)

Inhalation radiotoxicity of irradiated thorium as a heavy water reactor fuel

Energy Technology Data Exchange (ETDEWEB)

Edwards, G.W.R.; Priest, N.D.; Richardson, R.B. [Atomic Energy of Canada Ltd., Chalk River, Ontario, K0J 1J0 (Canada)

2013-07-01

The online refueling capability of Heavy Water Reactors (HWRs), and their good neutron economy, allows a relatively high amount of neutron absorption in breeding materials to occur during normal fuel irradiation. This characteristic makes HWRs uniquely suited to the extraction of energy from thorium. In Canada, the toxicity and radiological protection methods dealing with personnel exposure to natural uranium (NU) spent fuel (SF) are well-established, but the corresponding methods for irradiated thorium fuel are not well known. This study uses software to compare the activity and toxicity of irradiated thorium fuel ('thorium SF') against those of NU. Thorium elements, contained in the inner eight elements of a heterogeneous high-burnup bundle having LEU (Low-enriched uranium) in the outer 35 elements, achieve a similar burnup to NU SF during its residence in a reactor, and the radiotoxicity due to fission products was found to be similar. However, due to the creation of such inhalation hazards as U-232 and Th-228, the radiotoxicity of thorium SF was almost double that of NU SF after sufficient time has passed for the decay of shorter-lived fission products. Current radio-protection methods for NU SF exposure are likely inadequate to estimate the internal dose to personnel to thorium SF, and an analysis of thorium in fecal samples is recommended to assess the internal dose from exposure to this fuel. (authors)

Dynamic Analysis of the Thorium Fuel Cycle in CANDU Reactors

International Nuclear Information System (INIS)

Jeong, Chang Joon; Park, Chang Je

2006-02-01

The thorium fuel recycle scenarios through the Canada deuterium uranium (CANDU) reactor have been analyzed for two types of thorium fuel: homogeneous ThO 2 UO 2 and ThO 2 UO 2 -DUPIC fuels. The recycling is performed through the dry process fuel technology which has a proliferation resistance. For the once-through fuel cycle model, the existing nuclear power plant construction plan was considered up to 2016, while the nuclear demand growth rate from the year 2016 was assumed to be 0%. After setting up the once-through fuel cycle model, the thorium fuel CANDU reactor was modeled to investigate the fuel cycle parameters. In this analysis, the spent fuel inventory as well as the amount of plutonium, minor actinides and fission products of the multiple recycling fuel cycle were estimated and compared to those of the once-through fuel cycle. From the analysis results, it was found that the closed or partially closed thorium fuel cycle can be constructed through the dry process technology. Also, it is known that both the homogeneous and heterogeneous thorium fuel cycles can reduce the SF accumulation and save the natural uranium resource compared with the once-through cycle. From the material balance view point, the heterogeneous thorium fuel cycle seems to be more feasible. It is recommended, however, the economic analysis should be performed in future

Dynamic Analysis of the Thorium Fuel Cycle in CANDU Reactors

Energy Technology Data Exchange (ETDEWEB)

Jeong, Chang Joon; Park, Chang Je

2006-02-15

The thorium fuel recycle scenarios through the Canada deuterium uranium (CANDU) reactor have been analyzed for two types of thorium fuel: homogeneous ThO{sub 2}UO{sub 2} and ThO{sub 2}UO{sub 2}-DUPIC fuels. The recycling is performed through the dry process fuel technology which has a proliferation resistance. For the once-through fuel cycle model, the existing nuclear power plant construction plan was considered up to 2016, while the nuclear demand growth rate from the year 2016 was assumed to be 0%. After setting up the once-through fuel cycle model, the thorium fuel CANDU reactor was modeled to investigate the fuel cycle parameters. In this analysis, the spent fuel inventory as well as the amount of plutonium, minor actinides and fission products of the multiple recycling fuel cycle were estimated and compared to those of the once-through fuel cycle. From the analysis results, it was found that the closed or partially closed thorium fuel cycle can be constructed through the dry process technology. Also, it is known that both the homogeneous and heterogeneous thorium fuel cycles can reduce the SF accumulation and save the natural uranium resource compared with the once-through cycle. From the material balance view point, the heterogeneous thorium fuel cycle seems to be more feasible. It is recommended, however, the economic analysis should be performed in future.

Self-Sustaining Thorium Boiling Water Reactors

Directory of Open Access Journals (Sweden)

Ehud Greenspan

2012-10-01

Full Text Available A thorium-fueled water-cooled reactor core design approach that features a radially uniform composition of fuel rods in stationary fuel assembly and is fuel-self-sustaining is described. This core design concept is similar to the Reduced moderation Boiling Water Reactor (RBWR proposed by Hitachi to fit within an ABWR pressure vessel, with the following exceptions: use of thorium instead of depleted uranium for the fertile fuel; elimination of the internal blanket; and elimination of absorbers from the axial reflectors, while increasing the length of the fissile zone. The preliminary analysis indicates that it is feasible to design such cores to be fuel-self-sustaining and to have a comfortably low peak linear heat generation rate when operating at the nominal ABWR power level of nearly 4000 MWth. However, the void reactivity feedback tends to be too negative, making it difficult to have sufficient shutdown reactivity margin at cold zero power condition. An addition of a small amount of plutonium from LWR used nuclear fuel was found effective in reducing the magnitude of the negative void reactivity effect and enables attaining adequate shutdown reactivity margin; it also flattens the axial power distribution. The resulting design concept offers an efficient incineration of the LWR generated plutonium in addition to effective utilization of thorium. Additional R&D is required in order to arrive at a reliable practical and safe design.

Neutronic design of a plutonium-thorium burner small nuclear reactor

International Nuclear Information System (INIS)

Hartanto, Donny

2010-02-01

A small nuclear reactor using thorium and plutonium fuel has been designed from the neutronic point of view. The thermal power of the reactor is 150 MWth and it is proposed to be used to supply electricity in an island in Indonesia. Thorium and plutonium fuel was chosen because in recent years the thorium fuel cycle is one of the promising ways to deal with the increasing number of plutonium stockpiles, either from the utilization of uranium fuel cycle or from nuclear weapon dismantling. A mixed fuel of thorium and plutonium will not generate the second generation of plutonium which will be a better way to incinerate the excess plutonium compared with the MOX fuel. Three kinds of plutonium grades which are the reactor grade (RG), weapon grade (WG), and spent fuel grade (SFG) plutonium, were evaluated as the thorium fuel mixture in the 17x17 Westinghouse PWR Fuel assembly. The evaluated parameters were the multiplication factor, plutonium depletion, fissile buildup, neutron spectrum, and temperature reactivity feedback. An optimization was also done to increase the plutonium depletion by changing the Moderator to Fuel Ratio (MFR). The computer codes TRITON (coupled NEWT and ORIGEN-S) in SCALE version 6 were used as the calculation tool for this assembly level. From the evaluation and optimization of the fuel assembly, the whole core was designed. The core was consisted of 2 types of thorium fuel with different plutonium grade and it followed the checkerboard loading pattern. A new concept of enriched burnable poison was also introduced to the core. The core life is 6.4 EFPY or 75 GWd/MTHM. It can burn up to 58% of its total mass of initial plutonium. VENTURE was used as the calculation tool for the core level

Thorium and Molten Salt Reactors: Essential Questions for Classroom Discussions

Science.gov (United States)

DiLisi, Gregory A.; Hirsch, Allison; Murray, Meredith; Rarick, Richard

2018-04-01

A little-known type of nuclear reactor called the "molten salt reactor" (MSR), in which nuclear fuel is dissolved in a liquid carrier salt, was proposed in the 1940s and developed at the Oak Ridge National Laboratory in the 1960s. Recently, the MSR has generated renewed interest as a remedy for the drawbacks associated with conventional uranium-fueled light-water reactors (LWRs) in use today. Particular attention has been given to the "thorium molten salt reactor" (TMSR), an MSR engineered specifically to use thorium as its fuel. The purpose of this article is to encourage the TPT community to incorporate discussions of MSRs and the thorium fuel cycle into courses such as "Physics and Society" or "Frontiers of Physics." With this in mind, we piloted a pedagogical approach with 27 teachers in which we described the underlying physics of the TMSR and posed five essential questions for classroom discussions. We assumed teachers had some preexisting knowledge of nuclear reactions, but such prior knowledge was not necessary for inclusion in the classroom discussions. Overall, our material was perceived as a real-world example of physics, fit into a standards-based curriculum, and filled a need in the teaching community for providing unbiased references of alternative energy technologies.

Thorium utilization

Energy Technology Data Exchange (ETDEWEB)

Trauger, D B [Oak Ridge National Lab., TN (USA)

1978-01-01

Some of the factors that provide incentive for the utilization of thorium in specific reactor types are explored and the constraints that stand in the way are pointed out. The properties of thorium and derived fuels are discussed, and test and reactor operating experience is reviewed. In addition, symbiotic systems of breeder and converter reactor are suggested as being particularly attractive systems for energy production. Throughout the discussion, the High-Temperature Gas-Cooled Reactor and Molten Salt Reactor are treated in some detail because they have been developed primarily for use with thorium fuel cycles.

Utilization of thorium in PWR type reactors

International Nuclear Information System (INIS)

Correa, F.

1977-01-01

Uranium 235 consumption is comparatively evaluated with thorium cycle for a PWR type reactor. Modifications are only made in fuels components. U-235 consumption is pratically unchanged in both cycles. Some good results are promised to the mixed U-238/Th-232 fuel cycle in 1/1 proportion [pt

Design of a thorium fuelled Advanced Heavy Water Reactor

International Nuclear Information System (INIS)

Krishnani, P.D.

2009-01-01

Full text: The main objective for development of Advanced Heavy Water Reactor (AHWR) is to demonstrate thorium fuel cycle technologies, along with several other advanced technologies required for next generation reactors, so that these are readily available in time for launching the third stage. The AHWR under design is a 300 MWe vertical pressure tube type thorium-based reactor cooled by boiling light water and moderated by heavy water. The fuel consists of (Th-Pu)O 2 and ( 233 ThU)O 2 pins. The fuel cluster is designed to generate maximum energy out of 233 U, which is bred in-situ from thorium and has a slightly negative void coefficient of reactivity, negative fuel temperature coefficient and negative power coefficient. For the AHWR, the well -proven pressure tube technology and online fuelling have been adopted. Core heat removal is by natural circulation of coolant during normal operation and shutdown conditions. Thus, it combines the advantages of light water reactors and PHWRs and removes the disadvantages of PHWRs. It has several passive safety systems for reactor normal operation, decay heat removal, emergency core cooling, confinement of radioactivity etc. The fuel cycle is based on the in-situ conversion of naturally available thorium into fissile 233 U in self sustaining mode. The uranium in the spent fuel will be reprocessed and recycled back into the reactor. The plutonium inventory will be kept a minimum and will come from fuel irradiated in Indian PHWRs. The 233 U required initially can come from the fast reactor programme or it can be produced by specially designing the initial core of AHWR using (Th,Pu)MOX fuel. There will be gradual transition from the initial core which will not contain any 233 U to an equilibrium core, which will have ( 233 U, Th) MOX fuel pins also in a composite cluster. The self sustenance is being achieved by a differential fuel loading of low and a relatively higher Pu in the composite clusters. The AHWR burns the

Thorium fuels for heavy water reactors. Romanian experience

International Nuclear Information System (INIS)

Glodeanu, F.; Mirion, I.; Mehedinteanu, S.; Balan, V.

1984-01-01

The renewed interest in thorium fuel cycle due to the increased demand for fissile materials has resulted in speeding up the related research and development activities. For heavy water reactors the thorium cycles, especially SSET, are very promising and many efforts are made to demonstrate their feasibility. In our country, at INPR, the research and development activity has been initiated in the following areas: the conceptual design of thorium bearing fuel elements; fuel modelling; nuclear grade thorium dioxide powder technology; mixed oxide fuel technology. In the design area, the key factors in performance limitation, especially at extended burnup have been accounted and different remedies proposed. An irradiation programme has been settled and will start this year. The modelling activities are focused on mixed oxide behaviour and material data measurements are in progress. In the nuclear grade thorium powder technology area, a good piece of work has been done to develop an integrated technology for monasite processing (thorium being a by-product in lanthanides extraction). As regards the mixed oxide fuel technology, efforts have been made to obtain (ThU)O 2 pellets with good homogeneity and high density at different compositions. Besides the mixing powders route, other non-conventional technologies for refabrication like: microspheres, pellet impregnation and clay extrusion are studied. Experimental fuel rods for irradiation testing have been manufactured. (author)

Fluor determination by alkaline hydrolysis of the uranium and thorium fluorides; Determinacion de fluor por hidrolisis alcalina en fluoruros de uranio y torio

Energy Technology Data Exchange (ETDEWEB)

Barrachina Gomez, L; Gasco Sanchez, L

1961-07-01

The alkaline hydrolysis of the uranium and thorium fluorides is studded and a new method for the determination of the fluoride, on the basis of a indirect volumetric titration with standard soda, is proposed. The compounds that may influence the hydrolysis of the uranium fluoride and that may be occasionally found in it as impurities are also studied. the method can be applied to the uranium fluoride except when there is a great quantity of F{sub 2}UO{sub 2} or UO{sub 3} present in the sample. (Author) 20 refs.

Use of nuclear filters in the determination of thorium with previous separation by precipitation with fluoride ions and latter liquid-liquid extraction with TOPO

International Nuclear Information System (INIS)

Estevez, J.; Betancourt, M.

1988-01-01

A method for the determination of thorium in phosphorites, that includes a previous separation of some interfering elements was elaborated. Thorium was precipitated with fluoride ions and the insoluble compound formed was separated by using nuclear filters. Latter and extraction was made with Xilene-TOPO and colour was developed with Ars III in organic phase. 19 refs

Nuclear calculation of the thorium reactor

International Nuclear Information System (INIS)

Hirakawa, Naohiro

1998-01-01

Even if for a reactor using thorium (and 233-U), its nuclear design calculation procedure is similar to the case using conventional 235-U, 238-U and plutonium. As nuclear composition varies with time on operation of nuclear reactor, calculation of its mean cross section should be conducted in details. At that time, one-group cross section obtained by integration over a whole of energy range is used for small member group. And, as the nuclear data for a base of its calculation is already prepared by JENDL3.2 and nuclear data library derived from it, the nuclear calculation of a nuclear reactor using thorium has no problem. From such a veiwpoint, IAEA has organized a coordinated research program of 'Potential of Th-based Fuel Cycles to Constrain Pu and to reduce Long-term Waste Toxicities' since 1996. All nations entering this program were regulated so as to institute by selecting a nuclear fuel cycle thinking better by each nation and to examine what cycle is expected by comparing their results. For a promise to conduct such neutral comparison, a comparison of bench mark calculations aiming at PWR was conducted to protect that the obtained results became different because of different calculation method and cross section adopted by each nation. Therefore, it was promoted by entrance of China, Germany, India, Israel, Japan, Korea, Russia and USA. The SWAT system developed by Tohoku University is used for its calculation code, by using which calculated results on the bench mark calculation at the fist and second stages and the nuclear reactor were reported. (G.K.)

Packed-fluidized-bed blanket concept for a thorium-fueled commercial tokamak hybrid reactor

International Nuclear Information System (INIS)

Chi, J.W.H.; Miller, J.W.; Karbowski, J.S.; Chapin, D.L.; Kelly, J.L.

1980-09-01

A preliminary design of a thorium blanket was carried out as a part of the Commercial Tokamak Hybrid Reactor (CTHR) study. A fixed fuel blanket concept was developed as the reference CTHR blanket with uranium carbide fuel and helium coolant. A fixed fuel blanket was initially evaluated for the thorium blanket study. Subsequently, a new type of hybrid blanket, a packed-fluidized bed (PFB), was conceived. The PFB blanket concept has a number of unique features that may solve some of the problems encountered in the design of tokamak hybrid reactor blankets. This report documents the thorium blanket study and describes the feasibility assessment of the PFB blanket concept

Economics and utilization of thorium in nuclear reactors. Technical annexes 1 and 2

International Nuclear Information System (INIS)

1978-05-01

An assessment of the impact of utilizing the 233 U/thorium fuel cycle in the U.S. nuclear economy is strongly dependent upon several decisions involving nuclear energy policy. These decisions include: (1) to recycle or not recycle fissile material; (2) if fissile material is recycled, to recycle plutonium, 233 U, or both; and (3) to deploy or not to deploy advanced reactor designs such as Fast Breeder Reactors (FBR's), High Temperature Gas Reactors (HTGR's), and Canadian Deuterium Uranium Reactors (CANDU's). This report examines the role of thorium in the context of the above policy decisions while focusing special attention on economics and resource utilization

Thorium-Based Fuel Cycles in the Modular High Temperature Reactor

Institute of Scientific and Technical Information of China (English)

CHANG Hong; YANG Yongwei; JING Xingqing; XU Yunlin

2006-01-01

Large stockpiles of civil-grade as well as weapons-grade plutonium have been accumulated in the world from nuclear power or other programs of different countries. One alternative for the management of the plutonium is to incinerate it in the high temperature reactor (HTR). The thorium-based fuel cycle was studied in the modular HTR to reduce weapons-grade plutonium stockpiles, while producing no additional plutonium or other transuranic elements. Three thorium-uranium fuel cycles were also investigated. The thorium absorption cross sections of the resolved and unresolved resonances were generated using the ZUT-DGL code based on existing resonance data. The equilibrium core of the modular HTR was calculated and analyzed by means of the code VSOP'94. The results show that the modular HTR can incinerate most of the initially loaded plutonium amounting to about 95.3% net 239Pu for weapons-grade plutonium and can effectively utilize the uranium and thorium in the thorium-uranium fuel cycles.

On the development of fast breeder reactors and the use of thorium in Brazil

International Nuclear Information System (INIS)

Ishiguro, Y.

1986-10-01

This work presents a discussion on the possibility of construction of fast breeder reactors in Brazil. It is specially concerned with the use of thorium which is abundant in our country. The main advantages of this projects are: develop fuel and reactor technology in Brazil, increase thorium research, demonstrate the safety of LMFBR and promote its public acceptance. (A.C.A.S.)

A Simplified Supercritical Fast Reactor with Thorium Fuel

Directory of Open Access Journals (Sweden)

Peng Zhang

2014-01-01

Full Text Available Super-Critical water-cooled Fast Reactor (SCFR is a feasible option for the Gen-IV SCWR designs, in which much less moderator and thus coolant are needed for transferring the fission heat from the core compared with the traditional LWRs. The fast spectrum of SCFR is useful for fuel breeding and thorium utilization, which is then beneficial for enhancing the sustainability of the nuclear fuel cycle. A SCFR core is constructed in this work, with the aim of simplifying the mechanical structure and keeping negative coolant void reactivity during the whole core life. A core burnup simulation scheme based on Monte Carlo lattice homogenization is adopted in this study, and the reactor physics analysis has been performed with DU-MOX and Th-MOX fuel. The main issues discussed include the fuel conversion ratio and the coolant void reactivity. The analysis shows that thorium-based fuel can provide inherent safety for SCFR without use of blanket, which is favorable for the mechanical design of SCFR.

Utilization of thorium in a Gas Turbine – Modular Helium Reactor

International Nuclear Information System (INIS)

Şahin, Hacı Mehmet; Erol, Özgür; Acır, Adem

2012-01-01

Highlights: ► Performance parameters for the original fuel in GT-MHR depending on time were found. ► A proper plutonium–thorium mixture ratio was found using the original fuel results. ► Performance comparison of plutonium mixture and original fuel was made. ► Comparison showed that weapons grade plutonium mixture can be used in the reactor. - Abstract: Gas Turbine-Modular Helium Reactor (GT-MHR) is one of the new types of the reactors with high efficiency and increased safety features. The usage of different kinds of fissile material in this reactor can increase the life of it. Weapons-grade plutonium (WGrPu), which can be acquired from the old dismantled nuclear weapons, can be an option in a GT-MHR. In order to increase the sustainability of the WGrPu resources this fuel can be mixed with thorium, which is a fertile material that can be found in the nature and has resources three times more than uranium. In this study, possibility of utilization of the weapons-grade plutonium–thorium mixture was investigated and an optimum mixture ratio was determined. The behavior of this mixture and the original fuel was studied by using MCNP5 1.4, Monteburns 2.0 and Origen 2.2 tools. Calculations showed that, a GT-MHR type reactor, which is using the original TRISO fuel particle mixture of 20% enriched uranium + natural uranium (original fuel) has an effective multiplication factor (k eff ) of 1.270. Corresponding to this k eff value the weapons grade plutonium/thorium oxide mixture was found 19%/81%. By using Monteburns Code, the operation time, which describes the time passed until the reactor reaches a k eff value of 1.02, was found as 515 days for the original fuel and 1175 days for the weapons grade plutonium mixture. Furthermore, the burn-up values for the original fuel and WGrPu fuels were found as 47.69 and 119.27 GWd/MTU, respectively.

Thorium fuel-cycle development through plutonium incineration by THORIMS-NES (Thorium Molten-Salt nuclear energy synergetics)

International Nuclear Information System (INIS)

Furukawa, K.; Furuhashi, A.; Chigrinov, S.E.

1996-01-01

Thorium fuel-cycle has benefit on not-only trans-U element reduction but also their incineration. The disadvantage of high gamma activity of fuel, which is useful for improving the resistance to nuclear proliferation and terrorism, can overcome by molten fluorides fuel, and practically by THORIMS-NES, symbiotically coupled with fission Molten-Salt Reactor (FUJI) and fissile-producing Accelerator Molten-Salt Breeder (AMSB). This will have wide excellent advantages in global application, and will be deployed by incinerating Pu and Producing 233 U. Some details of this strategy including time schedule are presented. 14 refs, 2 figs, 4 tabs

The importance of thorium in the context of the generation in advanced reactors and the IPEN's experience

International Nuclear Information System (INIS)

Lainetti, Paulo E.O.; Mindrisz, Ana C.; Freitas, Antonio A.

2011-01-01

Globally, the 80's and 90's years were characterized by a significant reduction in the rate of growth of nuclear energy. However, from the 2000's, there has been a significant change in the international arena, with the 'renaissance' of interest in nuclear energy, even in countries that had abandoned nuclear power. To answer questions like security, reducing the generation of radioactive waste, control of proliferation risks and long-term sustainability, some initiatives have been adopted by some countries. In 2000, the Department of Energy - DOE - United States created the GIF - Generation IV International Forum for Nuclear Reactors. Six reactor concepts were selected based on criteria such as: reduction of radioactive wastes, safety and cost effective to meet the increasing energy demand on a sustainable basis, being resistant to diversion of materials for nuclear weapons proliferation and safer against terrorist attacks. In this context, it becomes important to use thorium as nuclear fuel for the Generation IV Advanced Reactors, with startup scheduled for 2030. Although the thorium does not present significant commercial value nowadays, in a not too distant future it will probably be an important commodity. Unfortunately, contrarily to what is happening in most developed countries in recent years, Brazil is paying little attention to the thorium, even less than in the past, despite its large reserves. Thorium is three to four times more abundant than uranium in the Earth's crust and, although not fissile, all thorium can be used to produce 233 U, by absorption of neutrons and subsequent radioactive decay. This uranium isotope is an excellent fuel for use in almost all types of nuclear reactors. It is possible that the thorium constitutes the largest Brazilian energy reserve, supplanting much oil (despite the findings of the pre-salt) and uranium. Brazil has a long tradition in the thorium technology, from mining of monazite until the obtainment of high purity

A preliminary assessment of thorium as a fuel for thermal reactors

International Nuclear Information System (INIS)

Duret, M.F.; Halsall, M.J.

1965-08-01

This report presents a preliminary survey of the contributing factors to total fuel cost, for a variety of potentially economic fuel cycles. U 238 and Th 232 are considered as fertile materials with enrichments of U 235 , U 233 and plutonium. The total fuel cost comprises: (a) a fuel supply cost which is derived from a manufacturing cost and the fuel burnup, (b) as spent fuel credit, and (c) inventory charges. The interrelation of these three factors and their dependence on reactor flux, fuel burnup, the heat rating of the fuel and the interest rate are considered for each combination of fertile and fissile material. Results show inventory charges, spent fuel credit (hence processing costs) and fabrication costs have an important effect on the fuelling cost. In addition, using highly rated thorium-based fuels will affect reactor capital costs. Further, more detailed studies of reactor design, fuel design and fuel management schemes are now required to verify the attraction of using thorium as a reactor fuel. (author)

Aspects on thorium utilization in heavy water reactors

International Nuclear Information System (INIS)

1978-11-01

Some of the main problems of the Th - PHWR cycles are analyzed. With respect to the burnup limitations introduced by SSET cycle conditions and the burnup sensitivities of this reference cycle, estimates are presented using an integrated neutron-heavy element balance method. A PHWR of 1 GW(e) very similar to the CANDU current design was selected. In the case of 0.5% uranium losses, 11000 MWD/tHE and 13000 MWD/tHE were considered for U-235, respectively, for the Pu initialization of the cycle, the corresponding inventory being 4 t U-235/GW(e) and 5 t Pu (with 72% fissile content) per GW(e) for one year delay time between reactor out to reactor in, 66% capacity factor, 27 MW (fission)/tHE medium specific power. The following aspects are also analyzed: Safety problems associated with low delayed neutron fraction values; High and intermediate burnup fuel elements conceptual problems; Specific problems of thorium reprocessing; Specific problems for radioactive wastes and thorium storage; U-232 content evaluations and related fuel fabrication problems

Investigation of the use of thorium in LWRs for improving reactor core performance

International Nuclear Information System (INIS)

Lau, Cheuk Wah

2012-01-01

Thorium is a fertile material and most of the past research has focused on breeding thorium into fissile material to achieve a more sustainable use of nuclear power. However, the focus in this report is on using thorium to improve reactor core performance. The improvement of reactor core performance is achieved by increasing the thermal margins by homogeneously distributing thorium in the fuel pellets. A proposed uranium-thorium-based fuel assembly is simulated for the Swedish Ringhals-3 PWR core in a realistic demonstration. In order to fully grasp the benefits and drawbacks of the newly proposed uranium-thorium-based fuel, a reload safety evaluation has been performed. For a real core, the Swedish Radiation Safety Authority would require an identical evaluation method to ensure that safety criteria are met during the whole cycle. In this report, only a few key safety parameters, such as isothermal- and Doppler-temperature coefficients of reactivity, pin peak power, boron worth, shutdown margins, and core average beta-effective are presented. The calculations were performed by the two-dimensional transport code CASMO-4E, and the two group three dimensional nodal code SIMULATE-3K from Studsvik Scandpower. The results showed that the uranium-thorium-based fuel assembly improves the thermal margins, both in the pin peak power and the local power (Fq). The improved thermal margins would allow more flexible core loading patterns with less neutron leakage, and could be used in power uprated cores to offer better safety margins

Investigation of the use of thorium in LWRs for improving reactor core performance

Energy Technology Data Exchange (ETDEWEB)

Lau, Cheuk Wah

2012-07-01

Thorium is a fertile material and most of the past research has focused on breeding thorium into fissile material to achieve a more sustainable use of nuclear power. However, the focus in this report is on using thorium to improve reactor core performance. The improvement of reactor core performance is achieved by increasing the thermal margins by homogeneously distributing thorium in the fuel pellets. A proposed uranium-thorium-based fuel assembly is simulated for the Swedish Ringhals-3 PWR core in a realistic demonstration. In order to fully grasp the benefits and drawbacks of the newly proposed uranium-thorium-based fuel, a reload safety evaluation has been performed. For a real core, the Swedish Radiation Safety Authority would require an identical evaluation method to ensure that safety criteria are met during the whole cycle. In this report, only a few key safety parameters, such as isothermal- and Doppler-temperature coefficients of reactivity, pin peak power, boron worth, shutdown margins, and core average beta-effective are presented. The calculations were performed by the two-dimensional transport code CASMO-4E, and the two group three dimensional nodal code SIMULATE-3K from Studsvik Scandpower. The results showed that the uranium-thorium-based fuel assembly improves the thermal margins, both in the pin peak power and the local power (Fq). The improved thermal margins would allow more flexible core loading patterns with less neutron leakage, and could be used in power uprated cores to offer better safety margins.

A non-symmetric pillar[5]arene based on triazole-linked 8-oxyquinolines as a sequential sensor for thorium(IV) followed by fluoride ions.

Science.gov (United States)

Fang, Yuyu; Li, Caixia; Wu, Lei; Bai, Bing; Li, Xing; Jia, Yiming; Feng, Wen; Yuan, Lihua

2015-09-07

A novel non-symmetric pillar[5]arene bearing triazole-linked 8-oxyquinolines at one rim was synthesized and demonstrated as a sequential fluorescence sensor for thorium(iv) followed by fluoride ions with high sensitivity and selectivity.

Potential of thorium use in the HTR reactor

International Nuclear Information System (INIS)

Engelmann, P.; Hansen, U.; Kolb, G.; Leushacke, D.; Teuchert, E.; Werner, H.

1979-08-01

In this investigation, several types of reactors and fuel circulations are dealt with as they refer to the region of the Federal Republic of Germany and are compared with each other as to their need for uranium and their costs until 2100. This includes also an investigation covering the effects of a postponed application of uranium-saving reactors, a delayed reprocessing and two variants of the nuclear energy's contribution to electricity generation. After today's light water reactor (LWR) of the pressure water reactor type (DWR) and the sodium-cooled fast breeder (SBR) which is being developed, the technically rather developed helium-cooled high temperature reactor (HTR) is dealt with as another system. The high temperature reactor is, because of its high coolant temperatures, not only suitable as a nuclear power plant, but can also be used to substitute fossile energy sources on the heat market and is being developed in Germany also for use as process heat reactor for nuclear coal gasification. Here the application of nuclear energy is only considered with regard to the region of power generation. Besides the case of the LWR and HTR-operation without reprocessing and fuel recycling for all reactor systems, the calculations also take into consideration the case of the closed fuel recycling. While LWR and SBR are based on the uranium-plutonium-fuel recycling, the thorium-uranium fuel circulation is considered for the HTR with globular fuel elements. As investigations made until today are generally restricted to the system LWR/SBR and the uranium-plutonium circulation, a main concern of the investigations presented here is to show the potential of the Thorium-utilization in high-temperature reactors and to determine how this system can also be applied during the time period concerned to set up a nuclear energy strategy which is safe and profitable as far as the uranium supply is concerned. (orig./UA) 891 UA/orig.- 892 HIS [de

Thorium utilization: conversion ratio and fuel needs in thermal reactors

International Nuclear Information System (INIS)

Oosterkamp, W.J.

1975-01-01

As a preparatory study for thorium utilization in thermal reactors a study has been made of the fuel comsumption in existing reactor types. A quantitative description is given of the influence of enrichment, burnup, amount of structural material, choise of coolant and control requirements on the convertion ratio. The enrichment is an important factor and a low fuel comsumption can be achieved by increasing the enrichment

Indian programme on molten salt cooled nuclear reactors

International Nuclear Information System (INIS)

DuIera, I.V.; Vijayan, P.K.; Sinha, R.K.

2013-01-01

Bhabha Atomic Research Centre (BARC) is developing a 600 MWth pebble bed high temperature reactor, cooled by natural circulation of molten fluoride salts and is capable of supplying process heat at 1000 ℃ to facilitate hydrogen production by splitting water. BARC has also initiated studies for a reactor concept in which salts of molten fluoride fuel and coolant in fluid form, flows through the reactor core of graphite moderator, resulting in nuclear fission within the molten salt. For thorium fuel cycle, this concept is very attractive, since the fuel can be re-processed on-line, enabling it to be an efficient neutron breeder. (author)

Thorium Fuel Utilization Analysis on Small Long Life Reactor for Different Coolant Types

Science.gov (United States)

Permana, Sidik

2017-07-01

A small power reactor and long operation which can be deployed for less population and remote area has been proposed by the IAEA as a small and medium reactor (SMR) program. Beside uranium utilization, it can be used also thorium fuel resources for SMR as a part of optimalization of nuclear fuel as a “partner” fuel with uranium fuel. A small long-life reactor based on thorium fuel cycle for several reactor coolant types and several power output has been evaluated in the present study for 10 years period of reactor operation. Several key parameters are used to evaluate its effect to the reactor performances such as reactor criticality, excess reactivity, reactor burnup achievement and power density profile. Water-cooled types give higher criticality than liquid metal coolants. Liquid metal coolant for fast reactor system gives less criticality especially at beginning of cycle (BOC), which shows liquid metal coolant system obtains almost stable criticality condition. Liquid metal coolants are relatively less excess reactivity to maintain longer reactor operation than water coolants. In addition, liquid metal coolant gives higher achievable burnup than water coolant types as well as higher power density for liquid metal coolants.

Thorium fuel cycle analysis

Energy Technology Data Exchange (ETDEWEB)

Yamaji, K [Central Research Inst. of Electric Power Industry, Tokyo (Japan)

1980-07-01

Systems analysis of the thorium cycle, a nuclear fuel cycle accomplished by using thorium, is reported in this paper. Following a brief review on the history of the thorium cycle development, analysis is made on the three functions of the thorium cycle; (1) auxiliary system of U-Pu cycle to save uranium consumption, (2) thermal breeder system to exert full capacity of the thorium resource, (3) symbiotic system to utilize special features of /sup 233/U and neutron sources. The effects of the thorium loading in LWR (Light Water Reactor), HWR (Heavy Water Reactor) and HTGR (High Temperature Gas-cooled Reactor) are considered for the function of auxiliary system of U-Pu cycle. Analysis is made to find how much uranium is saved by /sup 233/U recycling and how the decrease in Pu production influences the introduction of FBR (Fast Breeder Reactor). Study on thermal breeder system is carried out in the case of MSBR (Molten Salt Breeder Reactor). Under a certain amount of fissile material supply, the potential system expansion rate of MSBR, which is determined by fissile material balance, is superior to that of FBR because of the smaller specific fissile inventory of MSBR. For symbiotic system, three cases are treated; i) nuclear heat supply system using HTGR, ii) denatured fuel supply system for nonproliferation purpose, and iii) hybrid system utilizing neutron sources other than fission reactor.

Nuclear energy from thorium

International Nuclear Information System (INIS)

Coote, G.E.

1977-06-01

Relevant topics in nuclear and reactor physics are outlined. These include: the thorium decay series; generation of fissile from fertile nuclides, in particular U-233 from Th-232; the princiiples underlying thermal breeder reactors; the production of U-232 in thorium fuel and its important influence on nuclear safeguards and the recycling of U-233. Development work is continuing on several types of reactor which could utilise thorium; each of these is briefly described and its possible role is assessed. Other tipics covered include safety aspects of thorium oxide fuel, reprocessing, fabrication of recycle fuel and the possibility of denaturing U-233 by adding natural uranium. It is concluded that previoue arguments for development of the thorium cycle are still valid but those relating to non-proliferation of weapons may become even more compelling. (auth.)

Systematic study on Thorium fuel

International Nuclear Information System (INIS)

Shibata, Toshikazu; Kimura, Itsuro; Iwata, Shiro; Furuya, Hirotaka; Suzuki, Susumu.

1988-01-01

Introduced is the activities of the Joint Research Project Team on Thorium Fuel organized by mainly university researchers in Japan and supported by the Ministry of Education, Science and Culture for seven years since 1980. Four major groups were organized; (1) nuclear data, reactor physics and design, (2) nuclear fuel, (3) down stream and (4) biological effects of thorium. The first group covered measurements and analysis on nuclear data of thorium related nuclides, experiment and analysis on nuclear characteristics of thorium containing cores, basic engineering on a thorium molten salt reactor, and designs of several types of reactors. Fabrication and irradiation tests of thorium oxide fuel, and basic studies on new type thorium fuels (e.g. carbide and nitride) were studied by the second group. The third group covered the use of solutions in reprocessing of spent fuel, behavior of fission products, immobilization of high level radioactive waste, and continuous reprocessing for a molten salt reactor. The fourth group performed the trace study for patients who had been intravascularly injected with thorotrast for diagnosis of war injuries during the Second World War. (author)

Accident analysis of heavy water cooled thorium breeder reactor

International Nuclear Information System (INIS)

Yulianti, Yanti; Su’ud, Zaki; Takaki, Naoyuki

2015-01-01

Thorium has lately attracted considerable attention because it is accumulating as a by-product of large scale rare earth mining. The objective of research is to analyze transient behavior of a heavy water cooled thorium breeder that is designed by Tokai University and Tokyo Institute of Technology. That is oxide fueled, PWR type reactor with heavy water as primary coolant. An example of the optimized core has relatively small moderator to fuel volume ratio (MFR) of 0.6 and the characteristics of the core are burn-up of 67 GWd/t, breeding ratio of 1.08, burn-up reactivity loss during cycles of < 0.2% dk/k, and negative coolant reactivity coefficient. One of the nuclear reactor accidents types examined here is Unprotected Transient over Power (UTOP) due to withdrawing of the control rod that result in the positive reactivity insertion so that the reactor power will increase rapidly. Another accident type is Unprotected Loss of Flow (ULOF) that caused by failure of coolant pumps. To analyze the reactor accidents, neutron distribution calculation in the nuclear reactor is the most important factor. The best expression for the neutron distribution is the Boltzmann transport equation. However, solving this equation is very difficult so that the space-time diffusion equation is commonly used. Usually, space-time diffusion equation is solved by employing a point kinetics approach. However, this approach is less accurate for a spatially heterogeneous nuclear reactor and the nuclear reactor with quite large reactivity input. Direct method is therefore used to solve space-time diffusion equation which consider spatial factor in detail during nuclear reactor accident simulation. Set of equations that obtained from full implicit finite-difference method is solved by using iterative methods. The indication of UTOP accident is decreasing macroscopic absorption cross-section that results large external reactivity, and ULOF accident is indicated by decreasing coolant flow. The

Accident analysis of heavy water cooled thorium breeder reactor

Energy Technology Data Exchange (ETDEWEB)

Yulianti, Yanti [Department of Physics, University of Lampung Jl. Sumantri Brojonegoro No.1 Bandar Lampung, Indonesia Email: y-yanti@unila.ac.id (Indonesia); Su’ud, Zaki [Department of Physics, Bandung Institute of Technology Jl. Ganesha 10 Bandung, Indonesia Email: szaki@fi.itb.ac.id (Indonesia); Takaki, Naoyuki [Department of Nuclear Safety Engineering Cooperative Major in Nuclear Energy (Graduate School) 1-28-1 Tamazutsumi,Setagayaku, Tokyo158-8557, Japan Email: ntakaki@tcu.ac.jp (Japan)

2015-04-16

Thorium has lately attracted considerable attention because it is accumulating as a by-product of large scale rare earth mining. The objective of research is to analyze transient behavior of a heavy water cooled thorium breeder that is designed by Tokai University and Tokyo Institute of Technology. That is oxide fueled, PWR type reactor with heavy water as primary coolant. An example of the optimized core has relatively small moderator to fuel volume ratio (MFR) of 0.6 and the characteristics of the core are burn-up of 67 GWd/t, breeding ratio of 1.08, burn-up reactivity loss during cycles of < 0.2% dk/k, and negative coolant reactivity coefficient. One of the nuclear reactor accidents types examined here is Unprotected Transient over Power (UTOP) due to withdrawing of the control rod that result in the positive reactivity insertion so that the reactor power will increase rapidly. Another accident type is Unprotected Loss of Flow (ULOF) that caused by failure of coolant pumps. To analyze the reactor accidents, neutron distribution calculation in the nuclear reactor is the most important factor. The best expression for the neutron distribution is the Boltzmann transport equation. However, solving this equation is very difficult so that the space-time diffusion equation is commonly used. Usually, space-time diffusion equation is solved by employing a point kinetics approach. However, this approach is less accurate for a spatially heterogeneous nuclear reactor and the nuclear reactor with quite large reactivity input. Direct method is therefore used to solve space-time diffusion equation which consider spatial factor in detail during nuclear reactor accident simulation. Set of equations that obtained from full implicit finite-difference method is solved by using iterative methods. The indication of UTOP accident is decreasing macroscopic absorption cross-section that results large external reactivity, and ULOF accident is indicated by decreasing coolant flow. The

Criticality analysis for mixed thorium-uranium fuel in the Angra-2 PWR reactor using KENO-VI

Energy Technology Data Exchange (ETDEWEB)

Wichrowski, Caio C.; Gonçalves, Isadora C.; Oliveira, Claudio L.; Vellozo, Sergio O.; Baptista, Camila O., E-mail: wichrowski@ime.eb.br, E-mail: isadora.goncalves@ime.eb.br, E-mail: d7luiz@yahoo.com.br, E-mail: vellozo@ime.eb.br, E-mail: camila.oliv.baptista@gmail.com [Instituto Militar de Engenharia (IME), Rio de Janeiro, RJ (Brazil). Seção de Engenharia Nuclear

2017-07-01

The increasing energy demand associated to the current sustainability challenges have given the thorium nuclear fuel cycle renewed interest in the scientific community. Studies have focused on energy production in different reactor designs through the fission of uranium 233, the product of thorium fertilization by neutrons. In order to make it possible for near future applications a strategy based on the adaptation of current nuclear reactors for the use of thorium fuels is being considered. In this work, bearing in mind these limitations, a code was used to evaluate the effect on criticality (k{sub inf}) of the mixing of thorium and uranium in different proportions in the fuel of a PWR, the German designed Angra-2 Brazilian reactor in order to scrutinise its behaviour and determine the feasibility of an adapted ThO{sub 2}-UO{sub 2} mixed fuel cycle using current PWR technology. The analysis is performed using the KENO-VI module in the SCALE 6.1 nuclear safety analysis simulation code and the information is taken from the Angra-2 FSAR (Final Security Analysis Report). (author)

A competitive thorium fuel cycle for pressurized water reactors of current technology

International Nuclear Information System (INIS)

Galperin, A.; Radkowsky, A.; Todosow, M.

2002-01-01

Two important issues may influence the development and public acceptance of the nuclear power worldwide: a reduction of proliferation potential and spent fuel disposal requirements of the nuclear fuel cycle. Both problems may be addressed effectively by replacement of uranium by thorium fertile part of the fuel. A practical and competitive fuel design to satisfy the described design objectives and constraints may be achieved by seed-blanket core, proposed by A. Radkowsky and implemented in Shippingport reactors. The main idea is to separate spatially the uranium part of the core (seed) from the thorium part of the core (blanket), and thus allow two separate fuel management routes for uranium and thorium parts of the fuel. The uranium part (seed) is optimized to supply neutrons to the subcritical thorium blanket. The blanket is designed to generate and bum insitu 233 U. (author)

Thorium resources and energy utilization (14)

International Nuclear Information System (INIS)

Unesaki, Hironobu

2014-01-01

After the accident at the Fukushima Daiichi Nuclear Power Station of Tokyo Electric Power Company, thorium reactor has been attracting attention from the viewpoint of safety. Regarding thorium as the resources for nuclear energy, this paper explains its estimated reserves in the whole world and each country, its features such as the situation of utilization, and the reason why it attracts attention now. The following three items are taken up here as the typical issues among the latest topics on thorium: (1) utilization of thorium as a tension easing measure against environmental effects involved in nuclear energy utilization, (2) thorium-based reactor as the next generation type reactor with improved safety, and (3) thorium utilization as the improvement policy of nuclear proliferation resistance. The outline, validity, and problems of these items are explained. Thorium reactor has been adopted as a research theme since the 1950s up to now mainly in the U.S. However, it is not enough in the aspect of technological development and also insufficient in the verification of reliability based on technological demonstration, compared with uranium-fueled light-water reactor. This paper explains these situations, and discusses the points for thorium utilization and future prospects. (A.O.)

Design Feasible Area on Water Cooled Thorium Breeder Reactor in Equilibrium States

International Nuclear Information System (INIS)

Sidik Permana; Naoyuki Takaki; Hiroshi Sekimoto

2006-01-01

Thorium as supplied fuel has good candidate for fuel material if it is converted into fissile material 233 U which shows superior characteristics in the thermal region. The Shippingport reactor used 233 U-Th fuel system, and the molten salt breeder reactor (MSBR) project showed that breeding is possible in a thermal spectrum. In the present study, feasibility of water cooled thorium breeder reactor is investigated. The key properties such as flux, η value, criticality and breeding performances are evaluated for different moderator to fuel ratios (MFR) and burn-ups. The results show the feasibility of breeding for different MFR and burn-ups. The required 233 U enrichment is about 2% - 9% as charge fuel. The lower MFR and the higher enrichment of 233 U are preferable to improve the average burn-up; however the design feasible window is shrunk. This core shows the design feasible window especially in relation to MFR with negative void reactivity coefficient. (authors)

Conceptual design of a passively safe thorium breeder Pebble Bed Reactor

International Nuclear Information System (INIS)

Wols, F.J.; Kloosterman, J.L.; Lathouwers, D.; Hagen, T.H.J.J. van der

2015-01-01

Highlights: • This work proposes three possible designs for a thorium Pebble Bed Reactor. • A high-conversion PBR (CR > 0.96), passively safe and within practical constraints. • A thorium breeder PBR (220 cm core) in practical regime, but not passively safe. • A passively safe breeder, requiring higher fuel reprocessing and recycling rates. - Abstract: More sustainable nuclear power generation might be achieved by combining the passive safety and high temperature applications of the Pebble Bed Reactor (PBR) design with the resource availability and favourable waste characteristics of the thorium fuel cycle. It has already been known that breeding can be achieved with the thorium fuel cycle inside a Pebble Bed Reactor if reprocessing is performed. This is also demonstrated in this work for a cylindrical core with a central driver zone, with 3 g heavy metal pebbles for enhanced fission, surrounded by a breeder zone containing 30 g thorium pebbles, for enhanced conversion. The main question of the present work is whether it is also possible to combine passive safety and breeding, within a practical operating regime, inside a thorium Pebble Bed Reactor. Therefore, the influence of several fuel design, core design and operational parameters upon the conversion ratio and passive safety is evaluated. A Depressurized Loss of Forced Cooling (DLOFC) is considered the worst safety scenario that can occur within a PBR. So, the response to a DLOFC with and without scram is evaluated for several breeder PBR designs using a coupled DALTON/THERMIX code scheme. With scram it is purely a heat transfer problem (THERMIX) demonstrating the decay heat removal capability of the design. In case control rods cannot be inserted, the temperature feedback of the core should also be able to counterbalance the reactivity insertion by the decaying xenon without fuel temperatures exceeding 1600 °C. Results show that high conversion ratios (CR > 0.96) and passive safety can be combined in

Automated methods for thorium determination in liquids, solids and aerosols

International Nuclear Information System (INIS)

Robertson, R.; Stuart, J.E.

1984-01-01

Methodology for determining trace thorium levels in a variety of sample types for compliance purposes was developed. Thorium in filtered water samples is concentrated by ferric hydroxide co-precipitation. Aerosols on glass-fibre, cellulose ester or teflon filters are acid digested and thorium is concentrated by lanthanum fluoride co-precipitation. Chemical separation and measurement are then done on a Technicon AAII-C auto-analyzer via TTA-solvent extraction and colorimetry using the thorium-arsenazo III colour complex. Solid samples are acid digested and thorium is concentrated and separated using lanthanum fluoride co-precipitation followed by anion-exchange chromatography. Measurement is then carried out on the autoanalyzer by direct development of the thorium-arsenazo III colour complex. Chemical yields are determined through the addition of thorium-234 tracer with assay by gamma-ray spectrometry. The sensitivities of the methods for liquids, aerosols and solids are approximately 1μg/L,0.5μg and 0.5 μg/g respectively. At thorium levels about ten times the detection limits, accuracy and reproducibility are typically +-10 percent for liquids and aerosols and +- 15 percent for solid samples

Thorium nuclear fuel cycle technology

International Nuclear Information System (INIS)

Eom, Tae Yoon; Do, Jae Bum; Choi, Yoon Dong; Park, Kyoung Kyum; Choi, In Kyu; Lee, Jae Won; Song, Woong Sup; Kim, Heong Woo

1998-03-01

Since thorium produces relatively small amount of TRU elements after irradiation in the reactor, it is considered one of possible media to mix with the elements to be transmuted. Both solid and molten-salt thorium fuel cycles were investigated. Transmutation concepts being studied involved fast breeder reactor, accelerator-driven subcritical reactor, and energy amplifier with thorium. Long-lived radionuclides, especially TRU elements, could be separated from spent fuel by a pyrochemical process which is evaluated to be proliferation resistance. Pyrochemical processes of IFR, MSRE and ATW were reviewed and evaluated in detail, regarding technological feasibility, compatibility of thorium with TRU, proliferation resistance, their economy and safety. (author). 26 refs., 22 figs

INR Recent Contributions to Thorium-Based Fuel Using in CANDU Reactors

International Nuclear Information System (INIS)

Prodea, I.; Mărgeanu, C. A.; Rizoiu, A.; Olteanu, G.

2014-01-01

The paper summarizes INR Pitesti contributions and latest developments to the Thorium-based fuel (TF) using in present CANDU nuclear reactors. Earlier studies performed in INR Pitesti revealed the CANDU design potential to use Recovered Uranium (RU) and Slightly Enriched Uranium (SEU) as alternative fuels in PHWRs. In this paper, we performed both lattice and CANDU core calculations using TF, revealing the main neutron physics parameters of interest: k-infinity, coolant void reactivity (CVR), channel and bundle power distributions over a CANDU 6 reactor core similar to that of Cernavoda, Unit 1. We modelled the so called Once Through Thorium (OTT) fuel cycle, using the 3D finite-differences DIREN code, developed in INR. The INR flexible SEU-43 bundle design was the candidate for TF carrying. Preliminary analysis regarding TF burning in CANDU reactors has been performed using the finite differences 3D code DIREN. TFs showed safety features improvement regarding lower CVRs in the case of fresh fuel use. Improvements added to the INR ELESIMTORIU- 1 computer code give the possibility to fairly simulate irradiation experiments in INR TRIGA research reactor. Efforts are still needed in order to get better accuracy and agreement of simulations to the experimental results. (author)

Feasibility study of self sustaining capability on water cooled thorium reactors for different power reactors

International Nuclear Information System (INIS)

Permana, S.; Takaki, N.; Sekimoto, H.

2007-01-01

Thorium fuel cycle can maintain the sustainable system of the reactor for self sustaining system for future sustainable development in the world. Some characteristics of thorium cycle show some advantages in relation to higher breeding capability, higher performance of burn-up and more proliferation resistant. Several investigations was performed to improve the breeding capability which is essential for maintaining the fissile sustainability during reactor operation in thermal reactor such as Shippingport reactor and molten salt breeder reactor (MSBR) project. The preliminary study of breeding capability on water cooled thorium reactor has been investigated for various power output. The iterative calculation system is employed by coupling the equilibrium fuel cycle burn-up calculation and cell calculation of PIJ module of SRAC2000. In this calculation, 1238 fission products and 129 heavy nuclides are employed. In the cell calculation, 26 heavy metals and 66 fission products and 1 pseudo FP are employed. The employed nuclear data library was JENDL 3.2. The reactor is fueled by 2 33U-Th Oxide and it has used the light water coolant as moderator. Some characteristics such as conversion ratio and void reactivity coefficient performances are evaluated for the systems. The moderator to fuel ratio (MFR) values and average burnups are studied for survey parameter. The parametric survey for different power outputs are employed from 10 MWt to 3000 MWt for evaluating the some characteristics of core size and leakage effects to the spectra profile, required enrichment, breeding capability, fissile inventory condition, and void reactivity coefficient. Different power outputs are employed in order to evaluate its effect to the required enrichment for criticality, breeding capability, void reactivity and fissile inventory accumulation. The obtained value of the conversion ratios is evaluated by using the equilibrium atom composition. The conversion ratio is employed based on the

Non-Proliferative, Thorium-Based, Core and Fuel Cycle for Pressurized Water Reactors

International Nuclear Information System (INIS)

Todosow, M.; Raitses, G.; Galperin, A.

2009-01-01

Two of the major barriers to the expansion of worldwide adoption of nuclear power are related to proliferation potential of the nuclear fuel cycle and issues associated with the final disposal of spent fuel. The Radkowsky Thorium Fuel (RTF) concept proposed by Professor A. Radkowsky offers a partial solution to these problems. The main idea of the concept is the utilization of the seed-blanket unit (SBU) fuel assembly geometry which is a direct replacement for a 'conventional' assembly in either a Russian pressurized water reactor (VVER-1000) or a Western pressurized water reactor (PWR). The seed-blanket fuel assembly consists of a fissile (U) zone, known as seed, and a fertile (Th) zone known as blanket. The separation of fissile and fertile allows separate fuel management schemes for the thorium part of the fuel (a subcritical 'blanket') and the 'driving' part of the core (a supercritical 'seed'). The design objective for the blanket is an efficient generation and in-situ fissioning of the U233 isotope, while the design objective for the seed is to supply neutrons to the blanket in a most economic way, i.e. with minimal investment of natural uranium. The introduction of thorium as a fertile component in the nuclear fuel cycle significantly reduces the quantity of plutonium production and modifies its isotopic composition, reducing the overall proliferation potential of the fuel cycle. Thorium based spent fuel also contains fewer higher actinides, hence reducing the long-term radioactivity of the spent fuel. The analyses show that the RTF core can satisfy the requirements of fuel cycle length, and the safety margins of conventional pressurized water reactors. The coefficients of reactivity are comparable to currently operating VVER's/PWR's. The major feature of the RTF cycle is related to the total amount of spent fuel discharged for each cycle from the reactor core. The fuel management scheme adopted for RTF core designs allows a significant decrease in the

Practical introduction of thorium fuel cycles

International Nuclear Information System (INIS)

Kasten, P.R.

1982-01-01

The pracitcal introduction of throrium fuel cycles implies that thorium fuel cycles compete economically with uranium fuel cycles in economic nuclear power plants. In this study the reactor types under consideration are light water reactors (LWRs), heavy water reactors (HWRs), high-temperature gas-cooled reactors (HTGRs), and fast breeder reactors (FBRs). On the basis that once-through fuel cycles will be used almost exclusively for the next 20 or 25 years, introduction of economic thorium fuel cycles appears best accomplished by commercial introduction of HTGRs. As the price of natural uranium increases, along with commercialization of fuel recycle, there will be increasing incentive to utilize thorium fuel cycles in heavy water reactors and light water reactors as well as in HTGRs. After FBRs and fuel recycle are commercialized, use of thorium fuel cycles in the blanket of FBRs appears advantageous when fast breeder reactors and thermal reactors operate in a symbiosis mode (i.e., where 233 U bred in the blanket of a fast breeder reactor is utilized as fissile fuel in thermal converter reactors)

Reactor physics and reactor strategy investigations into the fissionable material economy of the thorium and uranium cycle in fast breeder reactors and high temperature reactors

International Nuclear Information System (INIS)

Schikorr, W.M.

In this work the properties governing the fissionable material economy of the uranium and thorium cycles are investigated for the advanced reactor types currently under development - the fast breeder reactor (FBR) and the high temperature reactor (HTR) - from the point of view of the optimum utilization of the available nuclear fuel reserves and the continuance of supply of these reserves. For this purpose, the two reactor types are first of all considered individually and are subsequently discussed as a complementary overall system

Conversion rate for PWR reactors in thorium cycle

International Nuclear Information System (INIS)

Angelkorte, G.M.

1980-01-01

This work concerns to the determination of the conversion-rate for a PWR reactor with an enrichment of 7.47%, considering a cell, geometrically equal to Angra I, composed by Thorium and U-238 in a 1:1 relation. The study was performed considering neutrons of one and two groups of energy, according to the suggestion from other authors sup(1,2). It was also performed a study about the production and consumption of fissile material. (author)

A Simplified Supercritical Fast Reactor with Thorium Fuel

OpenAIRE

Peng Zhang; Kan Wang; Ganglin Yu

2014-01-01

Super-Critical water-cooled Fast Reactor (SCFR) is a feasible option for the Gen-IV SCWR designs, in which much less moderator and thus coolant are needed for transferring the fission heat from the core compared with the traditional LWRs. The fast spectrum of SCFR is useful for fuel breeding and thorium utilization, which is then beneficial for enhancing the sustainability of the nuclear fuel cycle. A SCFR core is constructed in this work, with the aim of simplifying the mechanical structure ...

Safety and Regulatory Issues of the Thorium Fuel Cycle

Energy Technology Data Exchange (ETDEWEB)

Ade, Brian [ORNL; Worrall, Andrew [ORNL; Powers, Jeffrey [ORNL; Bowman, Steve [ORNL; Flanagan, George [ORNL; Gehin, Jess [ORNL

2014-02-01

Thorium has been widely considered an alternative to uranium fuel because of its relatively large natural abundance and its ability to breed fissile fuel (233U) from natural thorium (232Th). Possible scenarios for using thorium in the nuclear fuel cycle include use in different nuclear reactor types (light water, high temperature gas cooled, fast spectrum sodium, molten salt, etc.), advanced accelerator-driven systems, or even fission-fusion hybrid systems. The most likely near-term application of thorium in the United States is in currently operating light water reactors (LWRs). This use is primarily based on concepts that mix thorium with uranium (UO2 + ThO2), add fertile thorium (ThO2) fuel pins to LWR fuel assemblies, or use mixed plutonium and thorium (PuO2 + ThO2) fuel assemblies. The addition of thorium to currently operating LWRs would result in a number of different phenomenological impacts on the nuclear fuel. Thorium and its irradiation products have nuclear characteristics that are different from those of uranium. In addition, ThO2, alone or mixed with UO2 fuel, leads to different chemical and physical properties of the fuel. These aspects are key to reactor safety-related issues. The primary objectives of this report are to summarize historical, current, and proposed uses of thorium in nuclear reactors; provide some important properties of thorium fuel; perform qualitative and quantitative evaluations of both in-reactor and out-of-reactor safety issues and requirements specific to a thorium-based fuel cycle for current LWR reactor designs; and identify key knowledge gaps and technical issues that need to be addressed for the licensing of thorium LWR fuel in the United States.

Remarks on the thorium cycle

International Nuclear Information System (INIS)

Teller, E.

1978-01-01

The use of thorium and neutrons to make 233 U would provide energy for many thousands of years. Thorium is more abundant than uranium and 233 U is the best fissile material for thermal neutron reactors. Four approaches to the use of thorium are worth developing: heavy water moderated reactors with conversion ratios greater than 0.9, such as modified CANDU with lower cost of separating D 2 O and 235 U; molten salt breeder reactors, from which fission products and excess fuel may be continuously removed; fusion-fission hybrids that produce adequate tritium and excess neutrons for sustenance and 233 U production in a subcritical thorium 233 U blanket; and by fission-initiated thermo-nuclear explosions in cavities in salt beds one mile below the earth's surface, yielding 233 U from the excess neutrons and thorium and decontaminated steam for power production. (author)

Thorium-Based Fuels Preliminary Lattice Cell Studies for Candu Reactors

International Nuclear Information System (INIS)

Margeanu, C.A.; Rizoiu, A.C.

2009-01-01

The choice of nuclear power as a major contributor to the future global energy needs must take into account acceptable risks of nuclear weapon proliferation, in addition to economic competitiveness, acceptable safety standards, and acceptable waste disposal options. Candu reactors offer a proven technology, safe and reliable reactor technology, with an interesting evolutionary potential for proliferation resistance, their versatility for various fuel cycles creating premises for a better utilization of global fuel resources. Candu reactors impressive degree of fuel cycle flexibility is a consequence of its channel design, excellent neutron economy, on-power refueling, and simple fuel bundle. These features facilitate the introduction and exploitation of various fuel cycles in Candu reactors in an evolutionary fashion. The main reasons for our interest in Thorium-based fuel cycles have been, globally, to extend the energy obtainable from natural Uranium and, locally, to provide a greater degree of energy self-reliance. Applying the once through Thorium (OTT) cycle in existing and advanced Candu reactors might be seen as an evaluative concept for the sustainable development both from the economic and waste management points of view. Two Candu fuel bundles project will be used for the proposed analysis, namely the Candu standard fuel bundle with 37 fuel elements and the CANFLEX fuel bundle with 43 fuel elements. Using the Canadian proposed scheme - loading mixed ThO 2 -SEU CANFLEX bundles in Candu 6 reactors - simulated at lattice cell level led to promising conclusions on operation at higher fuel burnups, reduction of the fissile content to the end of the cycle, minor actinide content reduction in the spent fuel, reduction of the spent fuel radiotoxicity, presence of radionuclides emitting strong gamma radiation for proliferation resistance benefit. The calculations were performed using the lattice codes WIMS and Dragon (together with the corresponding nuclear data

A road map for the realization of global-scale thorium breeding fuel cycle by single molten-fluoride flow

International Nuclear Information System (INIS)

Furukawa, K.; Arakawa, K.; Erbay, L. B.

2007-01-01

For global survival in this century, we urgently need to launch a completely new global nuclear fission industry. To get worldwide public acceptance of nuclear energy, improvements are essential not only on safety, radio-waste management and economy but also especially nuclear proliferation resistance and safeguards. However, such global fission industry cannot replace the present fossil fuel industry in the next 50 years, unless the doubling-time of nuclear energy is less than 10 years, preferably 5-7 years. Such a doubling-time cannot be established by any kind of classical 'Fission Breeding Power Station' concept. We need a symbiotic system which couples fission power reactors with a system which can convert fertile thorium to fissile U-233, such as a spallation or D/T fusion (if and when it becomes available). For such a purpose, THORIMS-NES [Thorium Molten-Salt Nuclear Energy Synergetic System] has been proposed, which is composed of simple thermal fission power stations (FUJI) and fissile producing Accelerator Molten-Salt Breeder (AMSB). Its system functions are very ambitious, delicate and complex, but can be realized in the form of simple hardware applying the multifunctional 'single-phase molten-fluoride' circulation system. This system has no difficulties relating with 'radiation-damage', 'heat-removal' and 'chemical processing' owing to the simple 'idealistic ionic liquid' character. FUJI is size-flexible (economical even in smaller sizes), fuel self-sustaining without any continuous chemical processing and without core-graphite replacement, and AMSB is based on a single-fluid molten-salt target/blanket concept, which solves most engineering difficulties such as radiation-damage, heat-removal etc., except high-current proton accelerator development. Several AMSBs are accommodated in the regional centers (several ten sites in the world) with batch chemical processing plants including radio-waste management. The integrated thorium breeding fuel cycle is

An investigation into the feasibility of thorium fuels utilization in seed-blanket configurations for TRIGA PUSPATI Reactor (RTP)

Science.gov (United States)

Damahuri, Abdul Hannan Bin; Mohamed, Hassan; Aziz Mohamed, Abdul; Idris, Faridah

2018-01-01

Thorium is one of the elements that needs to be explored for nuclear fuel research and development. One of the popular core configurations of thorium fuel is seed-blanket configuration or also known as Radkowsky Thorium Fuel concept. The seed will act as a supplier of neutrons, which will be placed inside of the core. The blanket, on the other hand, is the consumer of neutrons that is located at outermost of the core. In this work, a neutronic analysis of seed-blanket configuration for the TRIGA PUSPATI Reactor (RTP) is carried out using Monte Carlo method. The reactor, which has been operated since 1982 use uranium zirconium hydride (U-ZrH1.6) as the fuel and have multiple uranium weight which are 8.5, 12 and 20 wt.%. The pool type reactor is one and only research reactor that located in Malaysia. The design of core included the Uranium Zirconium Hydride located at the centre of the core that will act as the seed to supply neutron. The thorium oxide that will act as blanket situated outside of seed region will receive neutron to transmute 232Th to 233U. The neutron multiplication factor or criticality of each configuration is estimated. Results show that the highest initial criticality achieved is 1.30153.

Development of fuel cycle technology for molten-salt reactor systems

International Nuclear Information System (INIS)

Uhlir, J.

2006-01-01

Full text: Full text: The Molten-Salt Reactor (MSR) represents one of promising advanced reactor type assigned to the GEN IV reactor systems. It can be operated either as thorium breeder within the Th -133U fuel cycle or as actinide transmuter incinerating transuranium fuel. Essentially the main advantage of MSR comes out from the prerequisite, that this reactor type should be directly connected with the 'on-line' reprocessing of circulating liquid (molten-salt) fuel. This principle should allow very effective extraction of freshly constituted fissile material (233U). Besides, the on-line fuel salt clean up is necessary within a long run to keep the reactor in operation. As a matter of principle, it permits to clear away typical reactor poisons like xenon, krypton, lanthanides etc. and possibly also other products of burned plutonium and transmuted minor actinides. The fuel salt clean up technology should be linked with the fresh MSR fuel processing to continuously refill the new fuel (thorium or transuranics) into the reactor system. On the other hand, the technologies of fresh transuranium molten-salt fuel processing from the current LWR spent fuel and of the on-line reprocessing of MSR fuel represent two killing points of the whole MSR technology, which have to be successfully solved before MSR deployment in the future. There are three main pyrochemical partitioning techniques proposed for processing and/or reprocessing of MSR fuel: Fluoride volatilization processes, Molten salt / liquid metal extraction processes and Electrochemical separation processes. Two of them - Fluoride Volatility Method and Electrochemical separation process from fluoride media are under development in the Nuclear Research Institute Rez pic. R and D in the field of Fluoride Volatility Method is concentrated to the development and verification of experimental semi-pilot technology for LWR spent fuel reprocessing, which may result in a product the form and composition of which might be

Gas Turbine Energy Conversion Systems for Nuclear Power Plants Applicable to LiFTR Liquid Fluoride Thorium Reactor Technology

Science.gov (United States)

Juhasz, Albert J.

2014-01-01

This panel plans to cover thermal energy and electric power production issues facing our nation and the world over the next decades, with relevant technologies ranging from near term to mid-and far term.Although the main focus will be on ground based plants to provide baseload electric power, energy conversion systems (ECS) for space are also included, with solar- or nuclear energy sources for output power levels ranging tens of Watts to kilo-Watts for unmanned spacecraft, and eventual mega-Watts for lunar outposts and planetary surface colonies. Implications of these technologies on future terrestrial energy systems, combined with advanced fracking, are touched upon.Thorium based reactors, and nuclear fusion along with suitable gas turbine energy conversion systems (ECS) will also be considered by the panelists. The characteristics of the above mentioned ECS will be described, both in terms of their overall energy utilization effectiveness and also with regard to climactic effects due to exhaust emissions.

Conceptual design of a commercial accelerator driven thorium reactor

International Nuclear Information System (INIS)

Fuller, C. G.; Ashworth, R. W.

2010-01-01

This paper describes the substantial work done in underpinning and developing the concept design for a commercial 600 MWe, accelerator driven, thorium fuelled, lead cooled, power producing, fast reactor. The Accelerator Driven Thorium Reactor (ADTR TM) has been derived from original work by Carlo Rubbia. Over the period 2007 to 2009 Aker Solutions commissioned this concept design work and, in close collaboration with Rubbia, developed the physics, engineering and business model. Much has been published about the Energy Amplifier concept and accelerator driven systems. This paper concentrates on the unique physics developed during the concept study of the ADTR TM power station and the progress made in engineering and design of the system. Particular attention is paid to where the concept design has moved significantly beyond published material. Description of challenges presented for the engineering and safety of a commercial system and how they will be addressed is included. This covers the defining system parameters, accelerator sizing, core and fuel design issues and, perhaps most importantly, reactivity control. The paper concludes that the work undertaken supports the technical viability of the ADTR TM power station. Several unique features of the reactor mean that it can be deployed in countries with aspirations to gain benefit from nuclear power and, at 600 MWe, it fits a size gap for less mature grid systems. It can provide a useful complement to Generation III, III+ and IV systems through its ability to consume actinides whilst at the same time providing useful power. (authors)

Potentialities of the molten salt reactor concept for a sustainable nuclear power production based on thorium cycle in epithermal spectrum

International Nuclear Information System (INIS)

Nuttin, Alexis

2002-01-01

In the case of a significant nuclear contribution to world energy needs, the problem of present nuclear waste management pose the sustainability of the PWR fuel cycle back into question. Studies on storage and incineration of these wastes should therefore go hand in hand with studies on innovative systems dedicated to a durable nuclear energy production, as reliable, clean and safe as possible. We are here interested in the concept of molten salt reactor, whose fuel is liquid. This particularity allows an online pyrochemical reprocessing which gives the possibility to overcome some neutronic limits. In the late sixties, the MSBR (Molten Salt Breeder Reactor) project of a graphite-moderated fluoride molten salt reactor proved thus that breeding is attainable with thorium in a thermal spectrum, provided that the online reprocessing is appropriate. By means of simulation tools developed around the Monte Carlo code MCNP, we first re-evaluate the performance of a reference system, which is inspired by the MSBR project. The complete study of the pre-equilibrium transient of this 2,500 MWth reactor, started with 232 Th/ 233 U fuel, allows us to validate our reference choices. The obtained equilibrium shows an important reduction of inventories and induced radio-toxicities in comparison with the other possible fuel cycles. The online reprocessing is efficient enough to make the system breed, with a doubling time of about thirty years at equilibrium. From the reference system, we then test different options in terms of neutron economy, transmutation and control of reactivity. We find that the online reprocessing brings most of its flexibility to this system, which is particularly well adapted to power generation with thorium. The study of transition scenarios to this fuel cycle quantifies the limits of a possible deployment from the present French power stock, and finally shows that a rational management of the available plutonium would be necessary in any case. (author)

Potential for the near-term use of the thorium cycle in a sustainable way

International Nuclear Information System (INIS)

Wider, H.; Tucek, K.; Carlsson, J.

2007-01-01

Nuclear sustainability is generally believed to be only reachable through the building of many fast breeder reactors. This paper shows that there is another possibility by using existing reactors that are either thermal breeders or have at least a high conversion ratio and considerably smaller critical masses than fast systems. Earlier it was believed that thermal molten salt breeders could eventually use the thorium / 233U cycle, which doesn't generate minor actinides and is therefore a cleaner fuel cycle. In the meantime, it has become rather clear that CANDU reactors that use heavy water cooling can also be self-breeders. The CANDU reactors could generate themselves 233U in thorium targets and could become selfsustaining after 12 years. However, additional 233U could also be generated in LWRs and fast reactors. It is shown that this generation of 233U will allow a faster large-term nuclear expansion than fast reactors alone. There could actually be a synergy between thermal and fast breeders if the latter are run with Pu/Minor Actinides/Th fuel, which burns the minor actinides and generates sizeable amounts of 233U. The main problem is still the necessary reprocessing on which India is working and intends to have in 10 years a large scale reprocessing facility available. However, there is at least an existing method for removing the 233U by the fluoride volatility method and to further use it in CANDUs. For the preparation of the use of 233U, we should attempt to run thorium subassemblies in CANDUs, LWRs, and fast reactors. Besides breeding 233U or at least having a high conversion ratio, CANDUs have the further advantage that they don't need a pressure vessel and therefore could be built in large numbers faster than LWRs. (author)

Design and Analysis of Thorium-fueled Reduced Moderation Boiling Water Reactors

Science.gov (United States)

Gorman, Phillip Michael

The Resource-renewable Boiling Water Reactors (RBWRs) are a set of light water reactors (LWRs) proposed by Hitachi which use a triangular lattice and high void fraction to incinerate fuel with an epithermal spectrum, which is highly atypical of LWRs. The RBWRs operate on a closed fuel cycle, which is impossible with a typical thermal spectrum reactor, in order to accomplish missions normally reserved for sodium fast reactors (SFRs)--either fuel self-sufficiency or waste incineration. The RBWRs also axially segregate the fuel into alternating fissile "seed" regions and fertile "blanket" regions in order to enhance breeding and leakage probability upon coolant voiding. This dissertation focuses on thorium design variants of the RBWR: the self-sufficient RBWR-SS and the RBWR-TR, which consumes reprocessed transuranic (TRU) waste from PWR used nuclear fuel. These designs were based off of the Hitachi-designed RBWR-AC and the RBWR-TB2, respectively, which use depleted uranium (DU) as the primary fertile fuel. The DU-fueled RBWRs use a pair of axially segregated seed sections in order to achieve a negative void coefficient; however, several concerns were raised with this multi-seed approach, including difficulty with controlling the reactor and unacceptably high axial power peaking. Since thorium-uranium fuel tends to have much more negative void feedback than uranium-plutonium fuels, the thorium RBWRs were designed to use a single elongated seed to avoid these issues. A series of parametric studies were performed in order to find the design space for the thorium RBWRs, and optimize the designs while meeting the required safety constraints. The RBWR-SS was optimized to maximize the discharge burnup, while the RBWR-TR was optimized to maximize the TRU transmutation rate. These parametric studies were performed on an assembly level model using the MocDown simulator, which calculates an equilibrium fuel composition with a specified reprocessing scheme. A full core model was

Once-through thorium fuel cycle evaluation for TVA's Browns Ferry-3 Boiling Water Reactor

International Nuclear Information System (INIS)

Hopkins, G.C.

1982-05-01

This report documents benchmark evaluations to test thorium lattice predictive methods and neutron cross sections against available data and summarizes specific evaluations of the once-through thorium cycle when applied to the Browns Ferry-3 BWR. It was concluded that appreciable uncertainties in thorium cycle nuclear data cloud the ability to reliably predict the fuel cycle performance and that power reactor irradiations of ThO 2 rods in BWRs are desirable to resolve uncertainties. Benchmark evaluations indicated that the ENDF/B-IV data used in the evaluations should cause an underprediction of U-233/ThO 2 fuel reactivity, and, therefore, the results of the preliminary evaluations completed under the program should be conservative

LFTR: in search of the ideal pathway to thorium utilization-development program and current status

International Nuclear Information System (INIS)

Soon, Benjamin

2015-01-01

Thorium has gained substantial attention as a potential energy source that could rival and eventually replace fossil fuels as humanity's primary energy source. This could not have come at a more opportune time as concerns about global climate change from CO 2 emissions and the approaching spectre of finite fossil fuel resources create serious challenges for the continuation of our advanced industrial societies, which are reliant on readily available and affordable energy. Thorium also potentially represents the catalyst with which the nuclear industry could reinvent itself and finally gain widespread public acceptance. There are many opinions on how to utilize thorium as a fuel, but the question of what constitutes an 'ideal' pathway has mostly been under-emphasized. Many specific characteristics of the thorium fuel cycle can differ significantly depending on the conditions and methodologies of utilization; characteristics such as safety, efficiency, waste profile and volume, and fissile protection can vary greatly according to reactor design and utilization philosophy. With thorium, we have been given an opportunity to start over, a blank slate. Therefore, in imagining the 'Thorium Economy' to come, it behoves the scientific and engineering communities to consider the most 'elegant' solution physically possible-what constitutes the 'ideal' and is it possible to reconcile it with what is both economically and technically practical? The characteristics desired of an 'ideal' nuclear reactor, in the areas of safety, efficiency, economy, and sustainability, and the 5 key design choices that could enable such a reactor will be discussed. This will be followed by an overview of the Liquid Fluoride Thorium Reactor, a 2-fluid Molten Salt Reactor currently under development by Flibe Energy in the United States. LFTR is a direct descendant of the MSRE, which was developed at Oak Ridge National Laboratory (ORNL) in the

Possible types of breeders with thorium cycle

International Nuclear Information System (INIS)

Ishiguro, Y.; Gouveia, A.S. de.

1981-02-01

Neutronics calculations of simplified homogeneous reactor models show the possibility that metal-fueled LMFBRs and coated particle fueled gas cooled reactors achieve reactor doubling times of around 10 years with the thorium cycle. Three concepts of gas-cooled thorium cycle breeders are discused. (Author) [pt

Neutronic analysis of two-fluid thorium molten salt reactor

International Nuclear Information System (INIS)

Frybort, Jan; Vocka, Radim

2009-01-01

The aim of this paper is to evaluate features of the two-fluid MSBR through a parametric study and compare its properties to one-fluid MSBR concepts. The starting point of the analysis is the original ORNL 1000 MWe reactor design, although simplified to some extent. We studied the influence of dimensions of distinct reactor parts - fuel and fertile channels radius, plenum height, design etc. - on fundamental reactor properties: breeding ratio and doubling time, reactor inventory, graphite lifetime, and temperature feedback coefficients. The calculations were carried out using MCNP5 code. Based on obtained results we proposed an improved reactor design. Our results show clear advantages of the concept with two separate fluoride salts if compared to the one fluid concept in breading, doubling time, and temperature feedback coefficients. Limitations of the two-fluid concept - particularly the graphite lifetime - are also pointed out. The reactor design can be a subject of further optimizations, namely from the viewpoint of reactor safety. (author)

Analysis of thorium and uranium fuel cycles in an iso-breeder lead fast reactor using extended-EQL3D procedure

International Nuclear Information System (INIS)

Fiorina, Carlo; Krepel, Jiri; Cammi, Antonio; Franceschini, Fausto; Mikityuk, Konstantin; Ricotti, Marco Enrico

2013-01-01

Highlights: ► Extension of EQL3D procedure to calculate radio-toxicity and decay heat. ► Characterization of uranium- and thorium-fueled LFR from BOL to equilibrium. ► Safety improvements for a LFR in a closed thorium cycle. ► Advantages of thorium-fueled LFR in terms of decay heat and radio-toxicity generation. ► Safety, decay heat and radio-toxicity concerns for a Th–Pu beginning-of-life core. - Abstract: Use of thorium in fast reactors has typically been considered as a secondary option, mainly thanks to a possible self-sustaining thorium cycle already in thermal reactors and due to the limited breeding capabilities compared to U–Pu in the fast neutron energy range. In recent years nuclear waste management has become more important, and the thorium option has been reconsidered for the claimed potential to burn transuranic waste and the lower build-up of hazardous isotopes in a closed cycle. To ascertain these claims and their limitations, the fuel cycle isotopic inventory, and associated waste radio-toxicity and decay heat, should be quantified and compared to the case of the uranium cycle using realistic core configurations, with complete recycle of all the actinides. Since the transition from uranium to thorium fuel cycles will likely involve a transuranic burning phase, this transition and the challenges that the evolving fuel actinide composition presents, for instance on reactor feedback parameters, should also be analyzed. In the present paper, these issues are investigated based on core physics analysis of the Lead-cooled Fast Reactor ELSY, performed with the fast reactor ERANOS code and the EQL3D procedure allowing full-core characterization of the equilibrium cycle and the transition cycles. In order to compute radio-toxicity and decay heat, EQL3D has been extended by developing a new module, which has been assessed against ORIGEN-S and is presented here. The capability of the EQL3D procedure to treat full-core 3D geometries allowed to

Process and apparatus for extraction of gases produced during operation of a fused-salt nuclear reactor

International Nuclear Information System (INIS)

Blum, J.; Marie, J.

1976-01-01

The present invention relates to the field of fused-salt nuclear reactors and its object is the extraction of the gases produced in the course of operation of these reactors. The process according to the invention consists in placing into position a piece of material permeable for gases and impermeable for the used fused salts, for instance, a piece of graphite, in such a way that part of the surface of this piece is in contact with the circuit of the radioactive salts and another part connected to a gas suction device. The piece could also be scavenged in its mass by a flow of inert gas. Application is contemplated in reactors using a mixture of lithium fluoride, beryllium fluoride, and uranium and/or thorium fluoride. 10 claims, 2 drawing figures

Preliminary Assessment of Heavy-Water Thorium Reactors in the Brazilian Nuclear Programme

Energy Technology Data Exchange (ETDEWEB)

Salvo Brito, S. de; Lepecki, W. P.S. [Instituto de Pesquisas Radioativas, Belo Horizonte (Brazil)

1968-04-15

Since December 1965, the Instituto de Pesquisas Radioativas has been studying for the Brazilian Nuclear Energy Commission the feasibility of a thorium reactor programme in Brazil; since June 1966, the programme has been developed in close co-operation with the French Atomic Energy Commission. A reference conceptual design of a heavy-water-cooled and -moderated thorium converter reactor has been developed. The main features of that concept are the use of a prestressed-concrete pressure vessel, integrated arrangement of the primary circuit and the possibility of on-load fuel management. Economic competitiveness could be the result of high compactness, low capital costs and low fuel consumption. The technology involved is not very sophisticated; intensive engineering development work must be done in areas like fuel charge machine, concrete vessel insulation, and proper design of heat exchangers, but it is the feeling of the Group that these problems could be solved without seriously compromising the economic feasibility of the concept. Preliminary studies were made on the alternative use of enriched uranium or plutonium as a feed for the programme; in the latter case, plutonium could be produced in natural uranium reactors of the same type. The general conditions favouring each of these approaches to the thorium cycle have been determined, in particular those related to the costs of the fissile materials in the world market and to the country's policy related to nuclear fuel imports. The results of the preliminary studies are very encouraging and could justify the beginning of a research and development programme leading to the construction of a prototype in the 1970's. (author)

Comparison of two thorium fuel cycles for use in light water prebreeder/breeder reactor systems (AWBA Development Program)

International Nuclear Information System (INIS)

Merriman, F.C.; McCoy, D.F.; Boyd, W.A.; Dwyer, J.R.

1983-05-01

Light water prebreeder/breeder conceptual reactor systems have been developed which have the potential to significantly improve the fuel utilization of present generation light water reactors. The purpose of this study is to describe and compare two possible types of thorium fuel cycles for use in these light water prebreeder and breeder concepts. The two types of thorium fuel cycles basically differ in the fuel rod design used in the prebreeder cores and the uranium isotopic concentration of fuel supplied to the breeder cores

A thorium breeder reactor concept for optimal energy extraction from uranium and thorium

International Nuclear Information System (INIS)

Jagannnathan, V.; Lawande, S.V.

1999-01-01

An attractive thorium breeder reactor concept has been evolved from simple physics based guidelines for induction of thorium in a major way in an otherwise enriched uranium reactor. D 2 O moderator helps to maximise reactivity for a given enrichment. A relatively higher flux level compared to LWRs offers the advantage of higher rate of 233 U production in thoria rods. Thus fresh thoria clusters consider no feed enrichment. In an equilibrium core, a full batch of pure thoria clusters are loaded during each fuel cycle. They undergo irradiation for about one year duration. By this time they accumulate nearly 70% of the asymptotic stable concentration of 233 U, if they face a flux level of the order of 10 14 n/cm 2 /sec. In the next fuel cycle, these thoria rods in ring cluster form are juxtaposed with the fresh enriched fuel rods, also in ring cluster form. Such integrated fuel assemblies are then irradiated for four or five fuel cycles, at the end of which U as well as Th rods attain a reasonably high burnup of about 30-32 MWD/kg. The core characteristics are quite attractive. The core excess reactivity remains low due to large thoria inventory which makes the net burnup reactivity load to be below 1%. The core is capable of being operated in an annual batch mode of operation like a LWR. The control requirement during power operation is negligible. Xenon over-ride requirement is low and can be managed by partial withdrawal of a few thoria clusters. Void reactivity is nearly zero or negative by the optimum design of the fuel cluster. Reactivity changes due to temperatures of fuel, coolant and moderator are also small. (author)

Comparison of open cycles of uranium and mixed oxides of thorium-uranium using advanced reactors

International Nuclear Information System (INIS)

Gonçalves, Letícia C.; Maiorino, José R.

2017-01-01

A comparative study of the mass balance and production costs of uranium oxide fuels was carried out for an AP1000 reactor and thorium-uranium mixed oxide in a reactor proposal using thorium called AP-Th1000. Assuming the input mass values for a fuel load the average enrichment for both reactors as well as their feed mass was determined. With these parameters, the costs were calculated in each fuel preparation process, assuming the prices provided by the World Nuclear Association. The total fuel costs for the two reactors were quantitatively compared with 18-month open cycle. Considering enrichment of 20% for the open cycle of mixed U-Th oxide fuel, the total uranium consumption of this option was 50% higher and the cost due to the enrichment was 70% higher. The results show that the use of U-Th mixed oxide fuels can be advantageous considering sustainability issues. In this case other parameters and conditions should be investigated, especially those related to fuel recycling, spent fuel storage and reduction of the amount of transuranic radioactive waste

Spallation symbiont and thorium breeding

International Nuclear Information System (INIS)

Furukawa, Kazuo

1991-01-01

The medium term world energy and environment countermeasures for 2020-2070 are not yet clearly established. The forecast of energy situation hereafter, its problems and the measures for solution are considered. World trend is removing borders, and the north-south problems are increasing the importance. The rational and clear idea with the support of concrete technology is required. The demand of energy will increase enormously at the annual rate of 2.3%. The world energy situation was forecast considering the increase of population, and it will be 115 TW at the end of the next century. The present status, problems and the countermeasures in nuclear fission energy technology are explained. The countermeasures should be based on three principles, namely Th-U-233 cycle, the utilization of molten fluoride fuel medium and the separation of molten salt breeders and molten salt reactors. Accelerator molten salt breeders, small molten salt reactors, the nuclear fuel cycle and the annihilation process for radioactive wastes are reported. The perspective that the nuclear energy system, in which the reactor safety, the measures to wastes and others are improved by the spallation-fission symbiont using thorium molten salt as the working medium, can be constructed is shown. (K.I.)

Transuranic Waste Burning Potential of Thorium Fuel in a Fast Reactor - 12423

Energy Technology Data Exchange (ETDEWEB)

Wenner, Michael; Franceschini, Fausto; Ferroni, Paolo [Westinghouse Electric Company LLC,Cranberry Township, PA, 16066 (United States); Sartori, Alberto; Ricotti, Marco [Politecnico di Milano, Milan (Italy)

2012-07-01

Westinghouse Electric Company (referred to as 'Westinghouse' in the rest of this paper) is proposing a 'back-to-front' approach to overcome the stalemate on nuclear waste management in the US. In this approach, requirements to further the societal acceptance of nuclear waste are such that the ultimate health hazard resulting from the waste package is 'as low as reasonably achievable'. Societal acceptability of nuclear waste can be enhanced by reducing the long-term radiotoxicity of the waste, which is currently driven primarily by the protracted radiotoxicity of the transuranic (TRU) isotopes. Therefore, a transition to a more benign radioactive waste can be accomplished by a fuel cycle capable of consuming the stockpile of TRU 'legacy' waste contained in the LWR Used Nuclear Fuel (UNF) while generating waste which is significantly less radio-toxic than that produced by the current open U-based fuel cycle (once through and variations thereof). Investigation of a fast reactor (FR) operating on a thorium-based fuel cycle, as opposed to the traditional uranium-based is performed. Due to a combination between its neutronic properties and its low position in the actinide chain, thorium not only burns the legacy TRU waste, but it does so with a minimal production of 'new' TRUs. The effectiveness of a thorium-based fast reactor to burn legacy TRU and its flexibility to incorporate various fuels and recycle schemes according to the evolving needs of the transmutation scenario have been investigated. Specifically, the potential for a high TRU burning rate, high U-233 generation rate if so desired and low concurrent production of TRU have been used as metrics for the examined cycles. Core physics simulations of a fast reactor core running on thorium-based fuels and burning an external TRU feed supply have been carried out over multiple cycles of irradiation, separation and reprocessing. The TRU burning capability as well as

Role of thorium in ensuring long term energy security to India

International Nuclear Information System (INIS)

Malhotra, S.K.

2013-01-01

Role of nuclear power in ensuring energy security to the world is inevitable due to a) dwindling fossil fuel resources and b) need for minimising green house gas emission that poses the risk of global climate change. India, keeping in mind its limited uranium and vast thorium resources, is pursuing a three stage nuclear power programme. The first stage is based on reactors that use uranium as fuel. It comprises of the indigenous Pressurised Heavy Water Reactors using natural uranium as fuel and light water reactors that employ enriched uranium as fuel and are to be set up in technical collaboration with other countries. The second stage is based on fast breeder reactors that employ plutonium derived from reprocessing of spent fuel from the first stage reactors. The third stage envisages reactors which will employ thorium based fuel after its irradiation in the second stage reactors. This programme is sequential in nature and has an ultimate objective of securing long term energy security to India through judicial use of its thorium resources. Thorium based reactors offer advantages in terms of better neutronic characteristics of thorium, it being better fertile host for plutonium disposition and better thermo-mechanical properties and slower fuel deterioration of thorium oxide. It is planned to introduce thorium in the Indian Nuclear Power Programme after sufficient (about 200 GWe) capacity build-up in the second stage. DAE is a global leader in the development of the entire thorium fuel cycle. It has a mature technology for extraction of thorium and preparation of thoria pellets. It has long back carried out irradiation of thoria pellets in its research reactors and also in PHWRs, post irradiation examination and reprocessing of irradiated thoria, fabrication of 233 U based fuel. It has KAMINI - the world's only operating reactor employing 233 U as fuel. An Advanced Heavy Water Reactor (AHWR) has been designed as a technology demonstrator for large scale

Research and development of thorium fuel cycle

International Nuclear Information System (INIS)

Oishi, Jun.

1994-01-01

Nuclear properties of thorium are summarized and present status of research and development of the use of thorium as nuclear fuel is reviewed. Thorium may be used for nuclear fuel in forms of metal, oxide, carbide and nitride independently, alloy with uranium or plutonium or mixture of the compound. Their use in reactors is described. The reprocessing of the spent oxide fuel in thorium fuel cycle is called the thorex process and similar to the purex process. A concept of a molten salt fuel reactor and chemical processing of the molten salt fuel are explained. The required future research on thorium fuel cycle is commented briefly. (T.H.)

Once-through uranium thorium fuel cycle in CANDU reactors

International Nuclear Information System (INIS)

Ozdemir, S.; Cubukcu, E.

2000-01-01

In this study, the performance of the once-through uranium-thorium fuel cycle in CANDU reactors is investigated. (Th-U)O 2 is used as fuel in all fuel rod clusters where Th and U are mixed homogeneously. CANDU reactors have the advantage of being capable of employing various fuel cycle options because of its good neutron economy, continuous on line refueling ability and axial fuel replacement possibility. For lattice cell calculations transport code WIMS is used. WIMS cross-section library is modified to achieve precise lattice cell calculations. For various enrichments and Th-U mixtures, criticality, heavy element composition changes, diffusion coefficients and cross-sections are calculate. Reactor core is modeled by using the diffusion code CITATION. We conclude that an overall saving of 22% in natural uranium demand can be achieved with the use of Th cycle. However, slightly enriched U cycle still consumes less natural Uranium and is a lot less complicated. (author)

PRE design of a molten salt thorium reactor loop

International Nuclear Information System (INIS)

Caire, Jean-Pierre; Roure, Anthony

2007-01-01

This study is a contribution to the 2004 PCR-RSF program of the Centre National de la Recherche Scientifique (CNRS) devoted to research on high temperature thorium molten salt reactors. A major issue of high temperature molten salt reactors is the very large heat duty to be transferred from primary to secondary loop of the reactor with minimal thermal losses. A possible inner loop made of a series of conventional graphite filter plate exchangers, pipes and pumps was investigated. The loop was assumed to use two counter current flows of the same LiF, BeF 2 , ZrF 4 , UF 4 molten salt flowing through the reactor. The 3D model used the coupling of k-ε turbulent Navier-Stokes equations and thermal applications of the Heat Transfer module of COMSOL Multiphysics. For a reactor delivering 2700 MWth, the model required a set of 114 identical exchangers. Each one was optimized to limit the heat losses to 2882 W. The pipes made of a succession of graphite, ceramics, Hastelloy-N alloy and insulating Microtherm layers led to a thermal loss limited to 550 W per linear meter. In such conditions, the global thermal losses represent only 0.013% of the reactor thermal power for elements covered with an insulator only 3 cm thick. (author)

Simulation on reactor TRIGA Puspati core kinetics fueled with thorium (Th) based fuel element

Energy Technology Data Exchange (ETDEWEB)

Mohammed, Abdul Aziz, E-mail: azizM@uniten.edu.my; Rahman, Shaik Mohmmed Haikhal Abdul [Universiti Tenaga Nasional. Jalan Ikram-UNITEN, 43000 Kajang, Selangor (Malaysia); Pauzi, Anas Muhamad, E-mail: anas@uniten.edu.my; Zin, Muhamad Rawi Muhammad; Jamro, Rafhayudi; Idris, Faridah Mohamad [Malaysian Nuclear Agency, Bangi, 43000 Kajang, Selangor (Malaysia)

2016-01-22

In confronting global energy requirement and the search for better technologies, there is a real case for widening the range of potential variations in the design of nuclear power plants. Smaller and simpler reactors are attractive, provided they can meet safety and security standards and non-proliferation issues. On fuel cycle aspect, thorium fuel cycles produce much less plutonium and other radioactive transuranic elements than uranium fuel cycles. Although not fissile itself, Th-232 will absorb slow neutrons to produce uranium-233 ({sup 233}U), which is fissile. By introducing Thorium, the numbers of highly enriched uranium fuel element can be reduced while maintaining the core neutronic performance. This paper describes the core kinetic of a small research reactor core like TRIGA fueled with a Th filled fuel element matrix using a general purpose Monte Carlo N-Particle (MCNP) code.

Thorium as an energy source. Opportunities for Norway; Thorium som energikilde - Muligheter for Norge

Energy Technology Data Exchange (ETDEWEB)

2008-02-15

Final Recommendations of the Thorium Report Committee: 1) No technology should be idolized or demonized. All carbon-dioxide (Co2) emission-free energy production technologies should be considered. The potential contribution of nuclear energy to a sustainable energy future should be recognized. 2) An investigation into the resources in the Fen Complex and other sites in Norway should be performed. It is essential to assess whether thorium in Norwegian rocks can be defined as an economical asset for the benefit of future generations. Furthermore, the application of new technologies for the extraction of thorium from the available mineral sources should be studied. 3) Testing of thorium fuel in the Halden Reactor should be encouraged, taking benefit of the well recognized nuclear fuel competence in Halden. 4) Norway should strengthen its participation in international collaborations by joining the EURATOM fission program and the GIF program on Generation IV reactors suitable for the use of thorium. 5) The development of an Accelerator Driven System (ADS) using thorium is not within the capability of Norway working alone. Joining the European effort in this field should be considered. Norwegian research groups should be encouraged to participate in relevant international projects, although these are currently focused on waste management. 6) Norway should bring its competence in waste management up to an international standard and collaboration with Sweden and Finland could be beneficial. 7) Norway should bring its competence with respect to dose assessment related to the thorium cycle up to an international standard. 8) Since the proliferation resistance of uranium-233 depends on the reactor and reprocessing technologies, this aspect will be of key concern should any thorium reactor be built in Norway. 9) Any new nuclear activities in Norway, e.g. thorium fuel cycles, would need strong international pooling of human resources, and in the case of thorium, a strong long

Feasibility study on the thorium fueled boiling water breeder reactor

International Nuclear Information System (INIS)

PetrusTakaki, N.

2012-01-01

The feasibility of (Th,U)O 2 fueled, boiling water breeder reactor based on conventional BWR technology has been studied. In order to determine the potential use of water cooled thorium reactor as a competitive breeder, this study evaluated criticality, breeding and void reactivity coefficient in response to changes made in MFR and fissile enrichments. The result of the study shows that while using light water as moderator, low moderator to fuel volume ratio (MFR=0.5), it was possible to breed fissile fuel in negative void reactivity condition. However the burnup value was lower than the value of the current LWR. On the other hand, heavy water cooled reactor shows relatively wider feasible breeding region, which lead into possibility of designing a core having better neutronic and economic performance than light water with negative void reactivity coefficient. (authors)

Depth-Resolved Cathodoluminescence of Thorium Dioxide

Science.gov (United States)

2013-03-01

plutonium-239 (239Pu)-based nuclear weapons. Thorium also results in less highly radioactive waste in comparison to the uranium fuels. Thorium is four...diameters (1/4 – 3/8”) (Mann & Thompson, 2010). The 99.99% ThO2 powder was placed into the ampoule with a basic mineralizer such as cesium fluoride...conversion ranging from 1 pA/V to 1 mA/V. The electrical noise is further reduced by cooling the PMT housing unit with liquid nitrogen as seen in

Radiotoxicity study of a boiling water reactor core design based on a thorium-uranium fuel concept

International Nuclear Information System (INIS)

Nunez C, A.; Espinosa P, G.

2007-01-01

Full text: The innovative design of a Boiling Water Reactor (BWR) equilibrium core using the thorium-uranium (blanket-seed) concept in the same integrated fuel assembly is presented in this paper. The lattice design uses the thorium conversion capability to 233 U in a BWR spectrum. A core design was developed to achieve an equilibrium cycle of one effective full power year in a standard BWR. A comparison of the toxicity of the spent fuel showed that toxicity is lower in the thorium cycle than other commercial fuels as UO 2 and MOX (uranium and plutonium) in case of the one-through cycle for LWR. (Author)

Utilization of thorium and U-ZrH1.6 fuels in various heterogeneous cores for TRIGA PUSPATI Reactor (RTP)

Science.gov (United States)

Damahuri, Abdul Hannan Bin; Mohamed, Hassan; Aziz Mohamed, Abdul; Idris, Faridah

2018-01-01

The use of thorium as nuclear fuel has been an appealing prospect for many years and will be great significance to nuclear power generation. There is an increasing need for more research on thorium as Malaysian government is currently active in the national Thorium Flagship Project, which was launched in 2014. The thorium project, which is still in phase 1, focuses on the research and development of the thorium extraction from mineral processing ore. Thus, the aim of the study is to investigate other alternative TRIGA PUSPATI Reactor (RTP) core designs that can fully utilize thorium. Currently, the RTP reactor has an average neutron flux of 2.797 x 1012 cm-2/s-1 and an effective multiplication factor, k eff, of 1.001. The RTP core has a circular array core configuration with six circular rings. Each ring consists of 6, 12, 18, 24, 30 or 36 U-ZrH1.6 fuel rods. There are three main type of uranium weight, namely 8.5, 12 and 20 wt.%. For this research, uranium zirconium hydride (U-ZrH1.6) fuel rods in the RTP core were replaced by thorium (ThO2) fuel rods. Seven core configurations with different thorium fuel rods placements were modelled in a 2D structure and simulated using Monte Carlo n-particle (MCNPX) code. Results show that the highest initial criticality obtained is around 1.35101. Additionally there is a significant discrepancy between results from previous study and the work because of the large estimated leakage probability of approximately 21.7% and 2D model simplification.

Interaction between thorium and potential clad materials

International Nuclear Information System (INIS)

Kale, G.B.; Gawde, P.S.; Sengupta, Pranesh

2005-01-01

Thorium based fuels are being used for nuclear reactors. The structural stability of fuel-clad assemblies in reactor systems depend upon the nature of interdiffusion reaction between fuel-cladding materials. Interdiffusion reaction thorium and various cladding materials is presented in this paper. (author)

The United States fluoride-salt-cooled high-temperature reactor program

International Nuclear Information System (INIS)

Holcomb, David E.

2013-01-01

The United States is pursuing the development of fluoride-salt-cooled high-temperature reactors (FHRs) through the Department of Energy's Office of Nuclear Energy (DOE-NE). FHRs, by definition, feature low-pressure liquid fluoride salt cooling, coated-particle fuel, a high-temperature power cycle, and fully passive decay heat rejection. FHRs, in principle, have the potential to economically generate large amounts of electricity while maintaining full passive safety. FHRs, however, remain a longer-term power production option. A principal development focus is, thus, on shortening, to the extent possible, the overall development time by focusing initial efforts on the longest lead-time issues. While FHRs represent a distinct reactor class, they inherit desirable attributes from other thermal power plants whose characteristics can be studied to provide general guidance on plant configuration, anticipated performance, and costs. Molten salt reactors provide experience on the materials, procedures, and components necessary to use liquid fluoride salts. Liquid-metal reactors provide design experience on using low-pressure liquid coolants, passive decay heat removal, and hot refueling. High-temperature gas-cooled reactors provide experience with coated-particle fuel and graphite components. Light-water reactors show the potential of transparent, high-heat-capacity coolants with low chemical reactivity. The FHR development efforts include both reactor concept and technology developments and are being broadly pursued. Oak Ridge National Laboratory (ORNL) provides technical leadership to the effort and is performing concept development on both a large base-load-type FHR as well as a small modular reactor (SMR) in addition to performing a broad scope of technology developments. Idaho National Laboratory (INL) is providing coated-particle fuel irradiation testing as well as developing high-temperature steam generator technology. The Massachusetts Institute of Technology (MIT

Development of an automated method for determination of thorium in soil samples and aerosols

International Nuclear Information System (INIS)

Stuart, J.E.; Robertson, R.

1986-09-01

Methodology for determining trace thorium levels in a variety of sample types was further developed. Thorium in filtered water samples is concentrated by ferric hydroxide precipitation followed by dissolution and co-precipitation with lanthanum fluoride. Aerosols on glass fibre, cellulose ester, or teflon filters and solid soil and sediment samples are acid digested. Subsequently thorium is concentrated by lanthanum fluoride co-precipitation. Chemical separation and measurement is then done on a Technicon AA11-C autoanalyzer, using solvent extraction into thenoyltrifuoroacetone in kerosene followed by back extraction into 2 N H NO 3 , and colourometric measurement of the thorium arsenazo III complex. Chemical yields are determined by the addition of thorium-234 tracer using gamma-ray spectrometry. The sensitivities of the methods for water, aerosol and solid samples are approximately 1.0 μg/L, 0.5 μg/g and 1.0 μg/g respectively. At thorium levels about ten times the detection limit, accuracy is estimated to be ± 10% for liquids and aerosols and ± 15% for solid samples, and precision ± 5% for all samples

Possible types of breeders with thorium cycle

International Nuclear Information System (INIS)

Ishiguro, Y.; Gouveia, A.S. de

1981-01-01

Neutronics calculations of simplified homogeneous reactor models show the possibility that metal-fueled LMFBRs and coated particle fueled gas cooled reactors achieve doubling times of around 10 years with the thorium cycle. Three concepts of gas-cooled thorium cycle breeders are discussed. (Author) [pt

Evaluation of thorium based nuclear fuel. Extended summary

International Nuclear Information System (INIS)

Franken, W.M.P.; Bultman, J.H.; Konings, R.J.M.; Wichers, V.A.

1995-04-01

Application of thorium based nuclear fuels has been evaluated with emphasis on possible reduction of the actinide waste. As a result three ECN-reports are published, discussing in detail: - The reactor physics aspects, by comparing the operation characteristics of the cores of Pressurized Water Reactors and Heavy Water Reactors with different fuel types, including equilibrium thorium/uranium free, once-through uranium fuel and equilibrium uranium/plutonium fuel, - the chemical aspects of thorium based fuel cycles with emphasis on fuel (re)fabrication and fuel reprocessing, - the possible reduction in actinide waste as analysed for Heavy Water Reactors with various types of thorium based fuels in once-through operation and with reprocessing. These results are summarized in this report together with a short discussion on non-proliferation and uranium resource utilization. It has been concluded that a substantial reduction of actinide radiotoxicity of the disposed waste may be achieved by using thorium based fuels, if very efficient partitioning and multiple recycling of uranium and thorium can be realized. This will, however, require large efforts to develop the technology to the necessary industrial scale of operation. (orig.)

Analysis of the thorium inclusion in the fuel of a fast reactor cooled by lead

International Nuclear Information System (INIS)

Juarez M, L. C.; Francois L, J. L.

2017-09-01

In the present work, we first verified a model of the European reactor cooled with lead (ELFR). The calculations were made with the code Monte Carlo serpent 2.27 and the library of cross sections Jeff-3.1. For this verification, three neutron parameters were compared: the evolution of the neutron multiplication factor, the Doppler constant and the effect of the vacuum fraction of the refrigerant, obtaining a good approximation with the reference values. Subsequently, the inclusion of thorium as a fertile material within the fuel was analyzed and the same neutron parameters were compared with the original fuel. The evolution of criticality for the case of thorium fuel differs significantly with respect to that of the original fuel (without thorium); this is due mainly to the breeding of the fissile isotope 233 U. Therefore, is possible to have a longer fuel cycle, favoring the availability factor of the plant, without compromising the performance of the reactor since both the Doppler constant and the effect of the vacuum fraction of the refrigerant show a similar tendency to those of the original fuel, being negative in both cases. (Author)

Recovery of protactinium from molten fluoride nuclear fuel compositions

Science.gov (United States)

Baes, C.F. Jr.; Bamberger, C.; Ross, R.G.

1973-12-25

A method is provided for separating protactinium from a molten fluonlde salt composition consisting essentially of at least one alkali and alkaline earth metal fluoride and at least one soluble fluoride of uranium or thorium which comprises oxidizing the protactinium in said composition to the + 5 oxidation state and contacting said composition with an oxide selected from the group consisting of an alkali metal oxide, an alkaline earth oxide, thorium oxide, and uranium oxide, and thereafter isolating the resultant insoluble protactinium oxide product from said composition. (Official Gazette)

The thorium fuel cycle

International Nuclear Information System (INIS)

Merz, E.R.

1977-01-01

The utilization of the thorium fuel cycle has long since been considered attractive owing to the excellent neutronic characteristics of 233 U, and the widespread and cheap thorium resources. Rapidly increasing uranium prices, public reluctance for widespread Pu recycling and expected delays for the market penetration of fast breeders have led to a reconsideration of the thorium fuel cycle merits. In addition, problems associated with reprocessing and waste handling, particularly with re-fabrication by remote handling of 233 U, are certainly not appreciably more difficult than for Pu recycling. To divert from uranium as a nuclear energy source it seems worth while intensifying future efforts for closing the Th/ 233 U fuel cycle. HTGRs are particularly promising for economic application. However, further research and development activities should not concentrate on this reactor type alone. Light- and heavy-water-moderated reactors, and even future fast breeders, may just as well take advantage of a demonstrated thorium fuel cycle. (author)

Moving towards sustainable thorium fuel cycles

International Nuclear Information System (INIS)

Hyland, B.; Hamilton, H.

2011-01-01

The CANDU reactor has an unsurpassed degree of fuel-cycle flexibility as a consequence of its fuel-channel design, excellent neutron economy, on-power refueling, and simple fuel bundle design. These features facilitate the introduction and full exploitation of thorium fuel cycles in CANDU reactors in an evolutionary fashion. Thoria (ThO 2 ) based fuel offers both fuel performance and safety advantages over urania (UO 2 ) based fuel, due its higher thermal conductivity which results in lower fuel-operating temperatures at similar linear element powers. Thoria fuel has demonstrated lower fission gas release than UO 2 under similar operating powers during test irradiations. In addition, thoria has a higher melting point than urania and is far less reactive in hypothetical accident scenarios owing to the fact that it has only one oxidation state. This paper examines one possible strategy for the introduction of thorium fuel cycles into CANDU reactors. In the short term, the initial fissile material would be provided in a heterogeneous bundle of low-enriched uranium and thorium. The medium term scenario uses homogeneous Pu/Th bundles in the CANDU reactor, further increasing the energy derived from the thorium. In the long term, the full energy potential from thorium would be realized through the recycle of the U-233 in the used fuel. With U-233 recycle in CANDU reactors, plutonium would then only be required to top up the fissile content to achieve the desired burnup. (author)

Advanced thorium cycles in LWRs and HWRs

International Nuclear Information System (INIS)

Radkowsky, A.

The main aspects of advanced thorium cycles in LWRs and HWRs are reviewed. New concepts include the seed blanket close packed heavy water breeder, the light water seed blanket thorium burner and self-induced thorium cycle in CANDU type reactors. (author)

U.S. leans toward denatured thorium cycle

International Nuclear Information System (INIS)

Smock, R.

1977-01-01

Denatured thorium appears to be the most promising among the nonproliferating alternatives to the plutonium cycle, which the Carter Administration is trying to cancel. Criteria for a better system include uranium utilization comparable to current light water reactors and minimal separation of fissile material into the waste stream. Comparisons with other systems conclude that thorium is preferable because it can lead to an acceptable fast breeder. The thorium cycle can be placed in energy centers for sensitive facilities and can also be introduced into ongoing light water systems. Reprocessing can be handled in the centers, where thorium can be mixed with plutonium for use in reactors within the center, while light water reactors operate on the outside. Any fuel leaving the center would be unsuitable for weapons. Later adaptation to in-center fast breeders will extend energy supplies, although a thorium breeder will be less efficient than a plutonium fast breeder. Denatured thorium is a technical answer to a complex political problem, but those in the nuclear industry see the U.S. goal of a nonproliferating fuel as futile in the light of world politics and breeder efforts in other countries

Electrochemical removal of fluoride from water by PAOA-modified carbon felt electrodes in a continuous flow reactor.

Science.gov (United States)

Cui, Hao; Qian, Yan; An, Hao; Sun, Chencheng; Zhai, Jianping; Li, Qin

2012-08-01

A novel poly(aniline-co-o-aminophenol) (PAOA) modified carbon felt electrode reactor was designed and investigated for fluoride removal from aqueous solutions. This reactor design is innovative because it operates under a wider pH range because of coating with a copolymer PAOA ion exchange film. In addition, contaminant mass transfer from bulk solution to the electrode surface is enhanced by the porous carbon felt as an electron-conducting carrier material compared to other reactors. The electrically controlled anion exchange mechanism was investigated by X-ray photoelectron spectroscopy and cyclic voltammetry. The applicability of the reactor in the field was tested through a series of continuous flow experiments. When the flow rate and initial fluoride concentration were increased, the breakthrough curve became sharper, which lead to a decrease in the breakthrough time and the defluoridation capacity of the reactor. The terminal potential values largely influenced fluoride removal by the reactor and the optimal defluoridation efficiency was observed at around 1.2V. The breakthrough capacities were all >10mg/g over a wide pH range (pH 5-9) with an initial fluoride concentration of 10mg/L. Consecutive treatment-regeneration studies over a week (once each day) revealed that the PAOA-modified carbon felt electrode could be effectively regenerated for reuse. The PAOA-modified carbon felt electrode reactor is a promising system that could be made commercially available for fluoride removal from aqueous solutions in field applications. Copyright © 2012 Elsevier Ltd. All rights reserved.

Determination of the total nitrate content of thorium nitrate solution with a selective electrode

International Nuclear Information System (INIS)

Wirkner, F.M.

1979-01-01

The nitrate content of thorium nitrate solutions is determined with a liquid membrane nitrate selective electrode utilizing the known addition method in 0.1 M potassium fluoride medium as ionic strength adjustor. It is studied the influence of pH and the presence of chloride, sulphate, phosphate, meta-silicate, thorium, rare earths, iron, titanium, uranium and zirconium at the same concentrations as for the aqueous feed solutions in the thorium purification process. The method is tested in synthetic samples and in samples proceeding from nitric dissolutions of thorium hidroxide and thorium oxicarbonate utilized as thorium concentrates to be purified [pt

Burn-up calculation of different thorium-based fuel matrixes in a thermal research reactor using MCNPX 2.6 code

Directory of Open Access Journals (Sweden)

Gholamzadeh Zohreh

2014-12-01

Full Text Available Decrease of the economically accessible uranium resources and the inherent proliferation resistance of thorium fuel motivate its application in nuclear power systems. Estimation of the nuclear reactor’s neutronic parameters during different operational situations is of key importance for the safe operation of nuclear reactors. In the present research, thorium oxide fuel burn-up calculations for a demonstrative model of a heavy water- -cooled reactor have been performed using MCNPX 2.6 code. Neutronic parameters for three different thorium fuel matrices loaded separately in the modelled thermal core have been investigated. 233U, 235U and 239Pu isotopes have been used as fissile element in the thorium oxide fuel, separately. Burn-up of three different fuels has been calculated at 1 MW constant power. 135X and 149Sm concentration variations have been studied in the modelled core during 165 days burn-up. Burn-up of thorium oxide enriched with 233U resulted in the least 149Sm and 135Xe productions and net fissile production of 233U after 165 days. The negative fuel, coolant and void reactivity of the used fuel assures safe operation of the modelled thermal core containing (233U-Th O2 matrix. Furthermore, utilisation of thorium breeder fuel demonstrates several advantages, such as good neutronic economy, 233U production and less production of long-lived α emitter high radiotoxic wastes in biological internal exposure point of view

Thorium and its future importance for nuclear energy generation

International Nuclear Information System (INIS)

Lainetti, Paulo E.O.

2015-01-01

Thorium was discovered in 1828 by the Swedish chemist Jons J. Berzelius. Despite some advantages over uranium for use in nuclear reactors, its main use, in the almost two centuries since its discovery, the use of thorium was restricted to use for gas mantles, especially in the early twentieth century. In the beginning of the Nuclear Era, many countries had interested on thorium, particularly during the 1950-1970 period. There are about 435 nuclear reactors in the world nowadays. They need more than 65.000 tons of uranium yearly. The future world energy needs will increase and, even if we assumed a conservative contribution of nuclear generation, it will be occur a significant increasing in the uranium prices, taking into account that uranium, as used in the present thermal reactors, is a finite resource. Thorium is nearly three times more abundant than uranium in the Earth's crust. Despite thorium is not a fissile material, 232 Th can be converted to 233 U (fissile) more efficiently than 238 U to 239 Pu. Besides this, since it is possible to convert thorium waste into nonradioactive elements, thorium is an environment-friendly alternative energy source. Thorium fuel cycle is also inherently resistant to proliferation. Some papers evaluate the thorium resources in Brazil over 1.200.000 metric t. Then, the thorium alternative must be seriously considered in Brazil for strategic reasons. In this paper a brief history of thorium is presented, besides a review of the world thorium utilization and a discussion about advantages and restrictions of thorium use. (author)

Radiological implications of plutonium recycle and the use of thorium fuels in power reactor operations

Energy Technology Data Exchange (ETDEWEB)

Macdonald, H. F.

1976-01-15

As economically attractive sources of natural uranium are gradually depleted attention will turn to recycling plutonium or to the use of thorium fuels. The radiological implications of these fuel cycles in terms of fuel handling and radioactive waste disposal are investigated in relation to a conventional /sup 235/U enriched oxide fuel. It is suggested that a comparative study of this nature may be an important aspect of the overall optimization of future fuel cycle strategies. It is shown that the use of thorium based fuels has distinct advantages in terms of neutron dose rates from irradiated fuels and long term proportional to decay heating commitment compared with conventional uranium/plutonium fuels. However, this introduces a ..gamma.. dose rate problem in the fabrication and handling of unirradiated /sup 233/U fuels. For both plutonium and thorium fuels these radiological problems increase during storage of the fuel prior to reactor irradiation. The novel health physics problems which arise in the handling and processing of thorium fuels are reviewed in an appendix.

Prospective thorium fuels for future nuclear energy generation

International Nuclear Information System (INIS)

Lainetti, Paulo E.O.

2017-01-01

In the beginning of the Nuclear Era, many countries were interested on thorium, particularly during the 1950 1970 periods. Nevertheless, since its discovery almost two centuries ago, the use of thorium has been restricted to gas mantles employed in gas lighting. The future world energy needs will increase and, even if we assumed a conservative contribution of nuclear generation, it will be occur a significant increasing in the uranium prices, taking into account that uranium, as used in the present thermal reactors, is a finite resource. Nowadays approximately the worldwide yearly requirement of uranium for about 435 nuclear reactors in operation is 65,000 metric t. Therefore, alternative solutions for future must be developed. Thorium is nearly three times more abundant than uranium in The Earth's crust. Despite thorium is not a fissile material, 232 Th can be converted to 233 U (fissile) more efficiently than 238 U to 239 Pu. Besides this, thorium is an environment alternative energy source and also inherently resistant to proliferation.. Many countries had initiated research on thorium in the past, Nevertheless, the interest evanesced due new uranium resources discoveries and availability of enriched uranium at low prices from obsolete weapons. Some papers evaluate the thorium resources in Brazil over 1.200.000 metric t. Then, the thorium alternative must be seriously considered in Brazil for strategic reasons. A brief history of thorium and its utilization are presented, besides a very short discussion about prospective thorium nuclear fuels for the next generation of nuclear reactors. (author)

Prospective thorium fuels for future nuclear energy generation

Energy Technology Data Exchange (ETDEWEB)

Lainetti, Paulo E.O., E-mail: lainetti@ipen.br [Instituto de Pesquisas Energeticas e Nucleares (IPEN/CNEN-SP), Sao Paulo, SP (Brazil)

2017-07-01

In the beginning of the Nuclear Era, many countries were interested on thorium, particularly during the 1950 1970 periods. Nevertheless, since its discovery almost two centuries ago, the use of thorium has been restricted to gas mantles employed in gas lighting. The future world energy needs will increase and, even if we assumed a conservative contribution of nuclear generation, it will be occur a significant increasing in the uranium prices, taking into account that uranium, as used in the present thermal reactors, is a finite resource. Nowadays approximately the worldwide yearly requirement of uranium for about 435 nuclear reactors in operation is 65,000 metric t. Therefore, alternative solutions for future must be developed. Thorium is nearly three times more abundant than uranium in The Earth's crust. Despite thorium is not a fissile material, {sup 232}Th can be converted to {sup 233}U (fissile) more efficiently than {sup 238}U to {sup 239}Pu. Besides this, thorium is an environment alternative energy source and also inherently resistant to proliferation.. Many countries had initiated research on thorium in the past, Nevertheless, the interest evanesced due new uranium resources discoveries and availability of enriched uranium at low prices from obsolete weapons. Some papers evaluate the thorium resources in Brazil over 1.200.000 metric t. Then, the thorium alternative must be seriously considered in Brazil for strategic reasons. A brief history of thorium and its utilization are presented, besides a very short discussion about prospective thorium nuclear fuels for the next generation of nuclear reactors. (author)

Adapting the deep burn in-core fuel management strategy for the gas turbine - modular helium reactor to a uranium-thorium fuel

International Nuclear Information System (INIS)

Talamo, Alberto; Gudowski, Waclaw

2005-01-01

In 1966, Philadelphia Electric has put into operation the Peach Bottom I nuclear reactor, it was the first high temperature gas reactor (HTGR); the pioneering of the helium-cooled and graphite-moderated power reactors continued with the Fort St. Vrain and THTR reactors, which operated until 1989. The experience on HTGRs lead General Atomics to design the gas turbine - modular helium reactor (GT-MHR), which adapts the previous HTGRs to the generation IV of nuclear reactors. One of the major benefits of the GT-MHR is the ability to work on the most different types of fuels: light water reactors waste, military plutonium, MOX and thorium. In this work, we focused on the last type of fuel and we propose a mixture of 40% thorium and 60% uranium. In a uranium-thorium fuel, three fissile isotopes mainly sustain the criticality of the reactor: 235 U, which represents the 20% of the fresh uranium, 233 U, which is produced by the transmutation of fertile 232 Th, and 239 Pu, which is produced by the transmutation of fertile 238 U. In order to compensate the depletion of 235 U with the breeding of 233 U and 239 Pu, the quantity of fertile nuclides must be much larger than that one of 235 U because of the small capture cross-section of the fertile nuclides, in the thermal neutron energy range, compared to that one of 235 U. At the same time, the amount of 235 U must be large enough to set the criticality condition of the reactor. The simultaneous satisfaction of the two above constrains induces the necessity to load the reactor with a huge mass of fuel; that is accomplished by equipping the fuel pins with the JAERI TRISO particles. We start the operation of the reactor with loading fresh fuel into all the three rings of the GT-MHR and after 810 days we initiate a refueling and shuffling schedule that, in 9 irradiation periods, approaches the equilibrium of the fuel composition. The analysis of the k eff and mass evolution, reaction rates, neutron flux and spectrum at the

The thorium fuel cycle

International Nuclear Information System (INIS)

Merz, E.R.

1977-01-01

The utilization of the thorium fuel cycle has long since been considered attractive due to the excellent neutronic characteristics of 233 U, and the widespread and cheap thorium resources. Although the uranium ore as well as the separative work requirements are usually lower for any thorium-based fuel cycle in comparison to present uranium-plutonium fuel cycles of thermal water reactors, interest by nuclear industry has hitherto been marginal. Fast increasing uranium prices, public reluctance against widespread Pu-recycling and expected retardations for the market penetration of fast breeders have led to a reconsideration of the thorium fuel cycle merits. In addition, it could be learned in the meantime that problems associated with reprocessing and waste handling, but particularly with a remote refabrication of 233 U are certainly not appreciably more difficult than for Pu-recycling. This may not only be due to psychological constraints but be based upon technological as well as economical facts, which have been mostly neglected up till now. In order to diversify from uranium as a nuclear energy source it seems to be worthwhile to greatly intensify efforts in the future for closing the Th/ 233 U fuel cycle. HTGR's are particularly promising for economic application. However, further R and D activites should not be solely focussed on this reactor type alone. Light and heavy-water moderated reactors, as well as even fast breeders later on, may just as well take advantage of a demonstrated thorium fuel cycle. A summary is presented of the state-of-the-art of Th/ 233 U-recycling technology and the efforts still necessary to demonstrate this technology all the way through to its industrial application

Burn-up calculation of fusion-fission hybrid reactor using thorium cycle

International Nuclear Information System (INIS)

Shido, S.; Matsunaka, M.; Kondo, K.; Murata, I.; Yamamoto, Y.

2006-01-01

A burn-up calculation system has been developed to estimate performance of blanket in a fusion-fission hybrid reactor which is a fusion reactor with a blanket region containing nuclear fuel. In this system, neutron flux is calculated by MCNP4B and then burn-up calculation is performed by ORIGEN2. The cross-section library for ORIGEN2 is made from the calculated neutron flux and evaluated nuclear data. The 3-dimensional ITER model was used as a base fusion reactor. The nuclear fuel (reprocessed plutonium as the fission materials mixed with thorium as the fertile materials), transmutation materials (minor actinides and long-lived fission products) and tritium breeder were loaded into the blanket. Performances of gas-cooled and water-cooled blankets were compared with each other. As a result, the proposed reactor can meet the requirement for TBP and power density. As far as nuclear waste incineration is concerned, the gas-cooled blanket has advantages. On the other hand, the water cooled-blanket is suited to energy production. (author)

Waste arisings from a high-temperature reactor with a uranium-thorium fuel cycle

International Nuclear Information System (INIS)

1979-09-01

This paper presents an equilibrium-recycle condition flow sheet for a high-temperature gas-cooled reactor (HTR) fuel cycle which uses thorium and high-enriched uranium (93% U-235) as makeup fuel. INFCE Working Group 7 defined percentage losses to various waste streams are used to adjust the heavy-element mass flows per gigawatt-year of electricity generated. Thorium and bred U-233 are recycled following Thorex reprocessing. Fissile U-235 is recycled one time following Purex reprocessing and then is discarded to waste. Plutonium and other transuranics are discarded to waste. Included are estimates of volume, radioactivity, and heavy-element content of wastes arising from HTR fuel element fabrication; HTR operation, maintenance, and decommissioning; and reprocessing spent fuel where the waste is unique to the HTR fuel cycle

R and D of On-line Reprocessing Technology for Molten-Salt Reactor Systems

International Nuclear Information System (INIS)

Uhlir, Jan; Tulackova, Radka; Chuchvalcova Bimova, Karolina

2006-01-01

The Molten Salt Reactor (MSR) represents one of promising future nuclear reactor concept included in the Generation IV reactors family. The reactor can be operated as the thorium breeder or as the actinide transmuter. However, the future deployment of Molten-Salt Reactors will be significantly dependent on the successful mastering of advanced reprocessing technologies dedicated to their fuel cycle. Here the on-line reprocessing technology connected with the fuel circuit of MSR is of special importance because the reactor cannot be operated for a long run without the fuel salt clean-up. Generally, main MSR reprocessing technologies are pyrochemical, majority of them are fluoride technologies. The proposed flow-sheets of MSR on-line reprocessing are based on a combination of molten-salt / liquid metal extraction and electro-separation processes, which can be added to the gas extraction process already verified during the MSRE project in ORNL. The crucial separation method proposed for partitioning of actinides from fission products is based on successive Anodic dissolution and Cathodic deposition processes in molten fluoride media. (authors)

A data base for PHW reactor operating on a once-through, low enriched uranium-thorium cycle

International Nuclear Information System (INIS)

Lungu, S.

1984-04-01

The study of a detailed data base for a new once-through uranium-thorium cycle using low enriched uranium (4 and 5,5% wt. U-235) and distinct UO 2 and ThO 2 fuel channels has been performed. With reference to a standard 638 MWe CANDU-type PHWR with 380 channels, evaluation of economics, fuel behaviour and safety has been performed. The Feinberg-Galanin method (code FEINGAL) has been used for calculation of axial flux distribution. All parameters have been provided by LATREP code following up the irradiation history. Economical assessment has shown that this fuel cycle is competitive with the natural uranium fuel cycle for 1979-based values of the parameters. Fuel behaviour and safety features modelling has shown that core behaviour of the uranium-thorium reactor under abnormal and accident conditions would be at least as good as that of the standard natural uranium reactor

Breeding capability and void reactivity analysis of heavy-water-cooled thorium reactor

International Nuclear Information System (INIS)

Permana, Sidik; Takaki, Naoyuki; Sekimoto, Hiroshi

2008-01-01

The fuel breeding and void reactivity coefficient of thorium reactors have been investigated using heavy water as coolant for several parametric surveys on moderator-to-fuel ratio (MFR) and burnup. The equilibrium fuel cycle burnup calculation has been performed, which is coupled with the cell calculation for this evaluation. The η of 233 U shows its superiority over other fissile nuclides in the surveyed MFR ranges and always stays higher than 2.1, which indicates that the reactor has a breeding condition for a wide range of MFR. A breeding condition with a burnup comparable to that of a standard PWR or higher can be achieved by adopting a larger pin gap (1-6 mm), and a pin gap of about 2 mm can be used to achieve a breeding ratio (BR) of 1.1. A feasible design region of the reactors, which fulfills the breeding condition and negative void reactivity coefficient, has been found. A heavy-water-cooled PWR-type Th- 233 U fuel reactor can be designed as a breeder reactor with negative void coefficient. (author)

Thorium converter (ThorCon) - a doable molten salt reactor

International Nuclear Information System (INIS)

Myneni, Ganapati

2015-01-01

ThorCon mass-producible nuclear power plants are being built to generate electricity cheaper than coal, at a scale to make a real improvement in world poverty and environment, now. ThorCon irradiated materials and fuel salt are designed to be replaced in four-year cycles with no impact on electricity generation. This flex-fuel plant and its replaceable reactor cans can operate with mixtures of thorium and uranium at multiple enrichments. Fuel salt can be NaF/BeF 2 or LiF/BeF 2 if available. ThorCon's design exceeds current nuclear power safety practice. The team calls for regulatory participation in rigorous testing of a full-scale prototype to develop licensing guidance

A fertile material, plentiful in nature. The thorium sector, energy for the next millenniums

International Nuclear Information System (INIS)

Perrier, Raymond

2014-01-01

Thorium exhibits very interesting properties. It is weakly radioactive, mainly emits weakly penetrating alpha radiations, produces 70 times more energy than uranium, is between three and four times more plentiful than uranium, and is consumed at 99 per cent in reactors whereas uranium is consumed at 1 per cent. This article first discusses the future of the uranium sector, and then presents the properties of thorium. It discusses ore types and the characteristics of the different types of deposits. It evokes world reserves and indicates the different types of nuclear reactors and the main isotopes they use. It describes the uranium sector related to nuclear reactors. It presents the principle of a thorium-fuelled nuclear reactor, recalls experiments performed since the 1950's in different countries (USA, Germany, India, so on) as well as the existence of some commercial reactors using thorium. It evokes more recent projects: proton accelerator reactors, molten salt reactors. It outlines the benefits and drawbacks of this last reactor type, and that Europe is late in the development of thorium-fuelled reactors with respect to China, USA and India

Light water reactors with a denatured thorium fuel cycle

International Nuclear Information System (INIS)

1978-05-01

Discussed in this paper is the performance of denatured thorium fuel cycles in PWR plants of conventional design, such as those currently in operation or under construction. Although some improvement in U 3 O 8 utilization is anticipated in PWRs optimized explicitly for the denatured thorium fuel cycle, this paper is limited to a discussion of the performance of denatured thorium fuels in conventional PWRs and consequently the data presented is representative of the use of thorium fuel in existing PWRs or those presently under construction. In subsequent sections of this paper, the design of the PWR, its performance on the denatured thorium fuel cycle, safety, accident and environmental considerations, and technological status and R and D requirements are discussed

Adapting the deep burn in-core fuel management strategy for the gas turbine - modular helium reactor to a uranium-thorium fuel

Energy Technology Data Exchange (ETDEWEB)

Talamo, Alberto [Department of Nuclear and Reactor Physics, Royal Institute of Technology, Roslagstullsbacken 21, S-10691, Stockholm (Sweden)]. E-mail: alby@neutron.kth.se; Gudowski, Waclaw [Department of Nuclear and Reactor Physics, Royal Institute of Technology, Roslagstullsbacken 21, S-10691, Stockholm (Sweden)

2005-11-15

In 1966, Philadelphia Electric has put into operation the Peach Bottom I nuclear reactor, it was the first high temperature gas reactor (HTGR); the pioneering of the helium-cooled and graphite-moderated power reactors continued with the Fort St. Vrain and THTR reactors, which operated until 1989. The experience on HTGRs lead General Atomics to design the gas turbine - modular helium reactor (GT-MHR), which adapts the previous HTGRs to the generation IV of nuclear reactors. One of the major benefits of the GT-MHR is the ability to work on the most different types of fuels: light water reactors waste, military plutonium, MOX and thorium. In this work, we focused on the last type of fuel and we propose a mixture of 40% thorium and 60% uranium. In a uranium-thorium fuel, three fissile isotopes mainly sustain the criticality of the reactor: {sup 235}U, which represents the 20% of the fresh uranium, {sup 233}U, which is produced by the transmutation of fertile {sup 232}Th, and {sup 239}Pu, which is produced by the transmutation of fertile {sup 238}U. In order to compensate the depletion of {sup 235}U with the breeding of {sup 233}U and {sup 239}Pu, the quantity of fertile nuclides must be much larger than that one of {sup 235}U because of the small capture cross-section of the fertile nuclides, in the thermal neutron energy range, compared to that one of {sup 235}U. At the same time, the amount of {sup 235}U must be large enough to set the criticality condition of the reactor. The simultaneous satisfaction of the two above constrains induces the necessity to load the reactor with a huge mass of fuel; that is accomplished by equipping the fuel pins with the JAERI TRISO particles. We start the operation of the reactor with loading fresh fuel into all the three rings of the GT-MHR and after 810 days we initiate a refueling and shuffling schedule that, in 9 irradiation periods, approaches the equilibrium of the fuel composition. The analysis of the k {sub eff} and mass

Design of an equilibrium nucleus of a BWR type reactor based in a Thorium-Uranium fuel

International Nuclear Information System (INIS)

Francois, J.L.; Nunez C, A.

2003-01-01

In this work the design of the reactor nucleus of boiling water using fuel of thorium-uranium is presented. Starting from an integral concept based in a type cover-seed assemble is carried out the design of an equilibrium reload for the nucleus of a reactor like that of the Laguna Verde Central and its are analyzed some of the main design variables like the cycle length, the reload fraction, the burnt fuel, the vacuum distribution, the generation of lineal heat, the margin of shutdown, as well as a first estimation of the fuel cost. The results show that it is feasible to obtain an equilibrium reload, comparable to those that are carried out in the Laguna Verde reactors, with a good behavior of those analyzed variables. The cost of the equilibrium reload designed with the thorium-uranium fuel is approximately 2% high that the uranium reload producing the same energy. It is concluded that it is convenient to include burnable poisons, type gadolinium, in the fuel with the end of improving the reload design, the fuel costs and the margin of shutdown. (Author)

Analysis of multi-scale spatial separation in a block-type thorium-loaded helium-cooled high-temperature reactor

International Nuclear Information System (INIS)

Huang, Jie; Ding, Ming

2017-01-01

Highlights: • Four-level of spatial separation is described in a block-type thorium-loaded HTR. • A traditional two-step calculation scheme is used to get the neutronic performance. • Fuel cycle cost is calculated by the levelised lifetime cost method. • Fuel cycle cost decreases with the increase of separation level or thorium content. • Effective enrichment basically determines the fuel cycle cost. - Abstract: With nuclear energy’s rapid development in recent years, supply of nuclear fuel has become increasingly important. Thorium has re-gained attention because of its abundant reserves and excellent physical properties. Compared to the homogeneous Th/U MOX fuel, separation of thorium and uranium in space is a better use of thorium. Therefore, this paper describes four-level spatial separation – no separation, tristructural-isotropic (TRISO) level, channel level and block level – in a block-type thorium-loaded helium-cooled high-temperature reactor (HTR). A traditional two-step calculation scheme, lattice calculation followed by core calculation, is used to get the neutronic performance of the equilibrium cycle, including uranium enrichment, mass of fuel, effective multiplication factor, and average conversion ratio. Based on these data, the fuel cycle cost of different-scale spatial separation can be calculated by the levelised lifetime cost method as a function of thorium content. As the separation level increases from no separation to channel level, the effective enrichment decreases 15% due to the increase of resonance escape probability. So there is a 13% drop for the fuel cycle cost. For TRISO-level separation, as the thorium content increases from 9 to 57%, the effective enrichment decreases 14% because of the superior breeding capacity of U-233. As a result, the fuel cycle cost also has about a 12% decrease. From the perspective of fuel cycle economics, channel-level separation with 60% thorium content is suggested.

Thorium-based nuclear fuel: current status and perspectives

International Nuclear Information System (INIS)

1987-03-01

Until the present time considerable efforts have already been made in the area of fabrication, utilization and reprocessing of Th-based fuels for different types of reactors, namely: by FRG and USA - for HTRs; FRG and Brazil, Italy - for LWRs; India - for HWRs and FBRs. Basic research of thorium fuels and thorium fuel cycles are also being undertaken by Australia, Canada, China, France, FRG, Romania, USSR and other countries. Main emphasis has been given to the utilization of thorium fuels in once-through nuclear fuel cycles, but in some projects closed thorium-uranium or thorium-plutonium fuel cycles are also considered. The purpose of the Technical Committee on the Utilization of Thorium-Based Nuclear Fuel: Current Status and Perspective was to review the world thorium resources, incentives for further exploration, obtained experience in the utilization of Th-based fuels in different types of reactors, basic research, fabrication and reprocessing of Th-based fuels. As a result of the panel discussion the recommendations on future Agency activities and list of major worldwide activities in the area of Th-based fuel were developed. A separate abstract was prepared for each of the 9 papers in this proceedings series

Contribution to the study of the conversion PWR type reactors to the thorium cycle

International Nuclear Information System (INIS)

Martins Filho, J.R.

1980-01-01

The use of the thorium cycle in PWR reactors is discussed. The fuel has been calculated in the equilibrium condition for a economic comparison with the uranium cycle (in the same condition). First of all, a code named EQUILIBRIO has been developed for the fuel equilibrium calculation. The results gotten by this code, were introduced in the LEOPARD code for the fuel depletion calculation (in the equilibrium cycle). Same important physics details of fuel depletion are studied, for instance: the neutron balance, power sharing, fuel burnup, etc. The calculations have been done taking as reference the Angra-1 PWR reactor. (Author) [pt

Heavy water reactors on the denatured thorium cycles

International Nuclear Information System (INIS)

1978-05-01

This paper presents preliminary technical and economic data to INFCE on the denatured U-233/Thorium fuel cycle for use in early comparisons of alternate nuclear systems. The once-through uranium fuel cycle is discussed in a companion paper. In presenting this preliminary information at this time, it is recognized that there are several other denatured thorium fuel cycles of potential interest, such as the U-235/thorium cycle which could be implemented at an earlier date. Information on these alternate cycles is currently being developed, and will be provided to INFCE when available

Thorium fuel cycle - Potential benefits and challenges

International Nuclear Information System (INIS)

2005-05-01

There has been significant interest among Member States in developing advanced and innovative technologies for safe, proliferation resistant and economically efficient nuclear fuel cycles, while minimizing waste and environmental impacts. This publication provides an insight into the reasons for renewed interest in the thorium fuel cycle, different implementation scenarios and options for the thorium cycle and an update of the information base on thorium fuels and fuel cycles. The present TECDOC focuses on the upcoming thorium based reactors, current information base, front and back end issues, including manufacturing and reprocessing of thorium fuels and waste management, proliferation-resistance and economic issues. The concluding chapter summarizes future prospects and recommendations pertaining to thorium fuels and fuel cycles

Status and development of the thorium fuel cycle

International Nuclear Information System (INIS)

Yi Weijing; Wei Renjie

2003-01-01

A perspective view of the thorium fuel cycle is provided in this paper. The advantages and disadvantages of the thorium fuel cycle are given and the development of thorium fuel cycle in several types of reactors is introduced. The main difficulties in developing the thorium fuel cycle lie in the reprocessing and disposal of the waste and its economy, and the ways tried by foreign countries to solve the problems are presented in the paper

Future perspective of thorium based nuclear fuels and thorium potential of Turkey

International Nuclear Information System (INIS)

Unak, T.; Yildirim, Y.

2001-01-01

Today's nuclear technology has principally been based on the use of fissile U-235 and Pu-239. he existence of thorium in the nature and its potential use in the nuclear technology were not unfortunately into account with a sufficient importance. The global distributions of thorium and uranium reserves indicate that in general some developed countries such as the USA, Canada, Australia, France have considerable uranium reserves, and contrarily only some developing countries such as Turkey, Brazil, India, Egypt have considerable thorium reserves. The studies carried out on the thorium during the last 50 years have clearly showed that the thorium based nuclear fuels have the potential easily use in most of reactor types actually operated with the classical uranium based nuclear fuels without any considerable modification. In the case of the use of thorium based nuclear fuels in future nuclear energy production systems, the serious problems such as the excess of Pu-239, the proliferation potential of nuclear weapons, and also the anxious of nuclear terrorism will probably be resolved, and sustainable nuclear energy production will be realized in the next new century. (authors)

Future perspective of thorium based nuclear fuels and thorium potential of Turkey

International Nuclear Information System (INIS)

Unak, T.; Yildirim, Y.

2000-01-01

Today's nuclear technology has principally been based on the use of fissile U-235 and Pu-239. The existence of thorium in the nature and its potential use in the nuclear technology were not unfortunately into account with a sufficient importance. The global distributions of thorium and uranium reserves indicate that in general some developed countries such as the USA, Canada, Australia, France have considerable uranium reserves, and contrarily only some developing countries such as Turkey, Brazil, India, Egypt have considerable thorium reserves. The studies carried out on the thorium during the last 50 years have clearly showed that the thorium based nuclear fuels have the potential easily use in most of reactor types actually operated with the classical uranium based nuclear fuels without any considerable modification. In the case of the use of thorium based nuclear fuels in future nuclear energy production systems, the serious problems such as the excess of Pu-239, the proliferation potential of nuclear weapons, and also the anxious of nuclear terrorism will probably be resolved, and sustainable nuclear energy production will be realized in the next new century. (authors)

The analysis of the initiating events in thorium-based molten salt reactor

International Nuclear Information System (INIS)

Zuo Jiaxu; Song Wei; Jing Jianping; Zhang Chunming

2014-01-01

The initiation events analysis and evaluation were the beginning of nuclear safety analysis and probabilistic safety analysis, and it was the key points of the nuclear safety analysis. Currently, the initiation events analysis method and experiences both focused on water reactor, but no methods and theories for thorium-based molten salt reactor (TMSR). With TMSR's research and development in China, the initiation events analysis and evaluation was increasingly important. The research could be developed from the PWR analysis theories and methods. Based on the TMSR's design, the theories and methods of its initiation events analysis could be researched and developed. The initiation events lists and analysis methods of the two or three generation PWR, high-temperature gascooled reactor and sodium-cooled fast reactor were summarized. Based on the TMSR's design, its initiation events would be discussed and developed by the logical analysis. The analysis of TMSR's initiation events was preliminary studied and described. The research was important to clarify the events analysis rules, and useful to TMSR's designs and nuclear safety analysis. (authors)

Recovery of fluoride ion selective electrode

International Nuclear Information System (INIS)

Monteiro, R.P.G.

1988-01-01

A recovery procedure of fluoride ion selective electrode based upon the body radiography of inactive electrode and introduction of suitable internal regeneration solution, is developed. The recovered electrode was tested in standard solutions of fluoride ions (10 sup5) to 10 -1M showing as good performance as the new one. The fluor determination by potentiometric measurements with selective electrode is used in nuclear fuel cycle for quality control of thorium and uranium mixed oxide pellets and pellets of uranium dioxides. (author) [pt

Thorium as an energy source. Opportunities for Norway

International Nuclear Information System (INIS)

2008-01-01

Final Recommendations of the Thorium Report Committee: 1) No technology should be idolized or demonized. All carbon-dioxide (Co2) emission-free energy production technologies should be considered. The potential contribution of nuclear energy to a sustainable energy future should be recognized. 2) An investigation into the resources in the Fen Complex and other sites in Norway should be performed. It is essential to assess whether thorium in Norwegian rocks can be defined as an economical asset for the benefit of future generations. Furthermore, the application of new technologies for the extraction of thorium from the available mineral sources should be studied. 3) Testing of thorium fuel in the Halden Reactor should be encouraged, taking benefit of the well recognized nuclear fuel competence in Halden. 4) Norway should strengthen its participation in international collaborations by joining the EURATOM fission program and the GIF program on Generation IV reactors suitable for the use of thorium. 5) The development of an Accelerator Driven System (ADS) using thorium is not within the capability of Norway working alone. Joining the European effort in this field should be considered. Norwegian research groups should be encouraged to participate in relevant international projects, although these are currently focused on waste management. 6) Norway should bring its competence in waste management up to an international standard and collaboration with Sweden and Finland could be beneficial. 7) Norway should bring its competence with respect to dose assessment related to the thorium cycle up to an international standard. 8) Since the proliferation resistance of uranium-233 depends on the reactor and reprocessing technologies, this aspect will be of key concern should any thorium reactor be built in Norway. 9) Any new nuclear activities in Norway, e.g. thorium fuel cycles, would need strong international pooling of human resources, and in the case of thorium, a strong long

Thorium as an energy source. Opportunities for Norway

Energy Technology Data Exchange (ETDEWEB)

2008-01-15

Final Recommendations of the Thorium Report Committee: 1) No technology should be idolized or demonized. All carbon-dioxide (Co2) emission-free energy production technologies should be considered. The potential contribution of nuclear energy to a sustainable energy future should be recognized. 2) An investigation into the resources in the Fen Complex and other sites in Norway should be performed. It is essential to assess whether thorium in Norwegian rocks can be defined as an economical asset for the benefit of future generations. Furthermore, the application of new technologies for the extraction of thorium from the available mineral sources should be studied. 3) Testing of thorium fuel in the Halden Reactor should be encouraged, taking benefit of the well recognized nuclear fuel competence in Halden. 4) Norway should strengthen its participation in international collaborations by joining the EURATOM fission program and the GIF program on Generation IV reactors suitable for the use of thorium. 5) The development of an Accelerator Driven System (ADS) using thorium is not within the capability of Norway working alone. Joining the European effort in this field should be considered. Norwegian research groups should be encouraged to participate in relevant international projects, although these are currently focused on waste management. 6) Norway should bring its competence in waste management up to an international standard and collaboration with Sweden and Finland could be beneficial. 7) Norway should bring its competence with respect to dose assessment related to the thorium cycle up to an international standard. 8) Since the proliferation resistance of uranium-233 depends on the reactor and reprocessing technologies, this aspect will be of key concern should any thorium reactor be built in Norway. 9) Any new nuclear activities in Norway, e.g. thorium fuel cycles, would need strong international pooling of human resources, and in the case of thorium, a strong long

Vil løyse global energikrise med thorium

CERN Multimedia

Aure, Gyri

2007-01-01

A professor from Bergen claims thorium can contribute to save the world from a global energy crisis. He wants Norway to construct the first accelerator driven reactor in the world powered by thorium. (5 pages)

Thorium valency in molten alkali halides in equilibrium with metallic thorium

International Nuclear Information System (INIS)

Smirnov, M.V.; Kudyakov, V.Ya.

1983-01-01

Metallic thorium is shown to corrode in molten alkali halides even in the absence of external oxidizing agents, alkali cations acting as oxidizing agents. Its corrosion rate grows in the series of alkali chlorides from LiCl to CsCl at constant temperature. Substituting halide anions for one another exerts a smaller influence, the rate rising slightly in going from chlorides to bromides and iodides, having the same alkali cations. Thorium valency is determined coulometrically, the metal being dissolved anodically in molten alkali halides and their mixtures. In fluoride melts it is equal to 4 but in chloride, bromide and iodide ones, as a rule, it has non-integral values between 4 and 2 which diminish as the temperature is raised, as the thorium concentration is lowered, as the radii of alkali cations decrease and those of halide anions increase. The emf of cells Th/N ThHlsub(n) + (1-N) MHl/MHl/C, Hlsub(2(g)) where Hl is Cl, Br or I, M is Li, Na, K, Cs or Na + K, and N < 0.05, is measured as a function of concentration at several temperatures. Expressions are obtained for its concentration dependence. The emf grows in the series of alkali chlorides from LiCl to CsCl, other conditions being equal. (author)

Thorium: Issues and prospects in Malaysia

Energy Technology Data Exchange (ETDEWEB)

AL-Areqi, Wadeeah M.; Majid, Amran Ab.; Sarmani, Sukiman; Bahri, Che Nor Aniza Che Zainul [Nuclear Science Programme, School of Applied Physics, Faculty of Science and Technology, Universiti Kebangsaan Malaysia, 43600 Bangi, Malaysia. walareqi@yahoo.com (Malaysia)

2015-04-29

In Malaysia, thorium exists in minerals and rare earth elements production residue. The average range of thorium content in Malaysian monazite and xenotime minerals was found about 70,000 and 15,000 ppm respectively. About 2,636 tonnes of Malaysian monazite was produced for a period of 5 years (2006-2010) and based on the above data, it can be estimated that Malaysian monazite contains about 184.5 tonnes of thorium. Although thorium can become a major radiological problem to our environment, but with the significant deposit of thorium in Malaysian monazite, it has a prospect as a future alternative fuel in nuclear technology. This paper will discuss the thorium issues in Malaysia especially its long term radiological risks to public health and environment at storage and disposal stages, the prospect of exploring and producing high purity thorium from our rare earth elements minerals for future thorium based reactor. This paper also highlights the holistic approach in thorium recovery from Malaysian rare earth element production residue to reduce its radioactivity and extraction of thorium and rare earth elements from the minerals with minimum radiological impact to health and environment.

Thorium: Issues and prospects in Malaysia

International Nuclear Information System (INIS)

AL-Areqi, Wadeeah M.; Majid, Amran Ab.; Sarmani, Sukiman; Bahri, Che Nor Aniza Che Zainul

2015-01-01

In Malaysia, thorium exists in minerals and rare earth elements production residue. The average range of thorium content in Malaysian monazite and xenotime minerals was found about 70,000 and 15,000 ppm respectively. About 2,636 tonnes of Malaysian monazite was produced for a period of 5 years (2006-2010) and based on the above data, it can be estimated that Malaysian monazite contains about 184.5 tonnes of thorium. Although thorium can become a major radiological problem to our environment, but with the significant deposit of thorium in Malaysian monazite, it has a prospect as a future alternative fuel in nuclear technology. This paper will discuss the thorium issues in Malaysia especially its long term radiological risks to public health and environment at storage and disposal stages, the prospect of exploring and producing high purity thorium from our rare earth elements minerals for future thorium based reactor. This paper also highlights the holistic approach in thorium recovery from Malaysian rare earth element production residue to reduce its radioactivity and extraction of thorium and rare earth elements from the minerals with minimum radiological impact to health and environment

Thorium: Issues and prospects in Malaysia

Science.gov (United States)

AL-Areqi, Wadeeah M.; Majid, Amran Ab.; Sarmani, Sukiman; Bahri, Che Nor Aniza Che Zainul

2015-04-01

In Malaysia, thorium exists in minerals and rare earth elements production residue. The average range of thorium content in Malaysian monazite and xenotime minerals was found about 70,000 and 15,000 ppm respectively. About 2,636 tonnes of Malaysian monazite was produced for a period of 5 years (2006-2010) and based on the above data, it can be estimated that Malaysian monazite contains about 184.5 tonnes of thorium. Although thorium can become a major radiological problem to our environment, but with the significant deposit of thorium in Malaysian monazite, it has a prospect as a future alternative fuel in nuclear technology. This paper will discuss the thorium issues in Malaysia especially its long term radiological risks to public health and environment at storage and disposal stages, the prospect of exploring and producing high purity thorium from our rare earth elements minerals for future thorium based reactor. This paper also highlights the holistic approach in thorium recovery from Malaysian rare earth element production residue to reduce its radioactivity and extraction of thorium and rare earth elements from the minerals with minimum radiological impact to health and environment.

All heavy metals closed-cycle analysis on water-cooled reactors of uranium and thorium fuel cycle systems

International Nuclear Information System (INIS)

Permana, Sidik; Sekimoto, Hiroshi; Waris, Abdul; Takaki, Naoyuki

2009-01-01

Uranium and Thorium fuels as the basis fuel of nuclear energy utilization has been used for several reactor types which produce trans-uranium or trans-thorium as 'by product' nuclear reaction with higher mass number and the remaining uranium and thorium fuels. The utilization of recycled spent fuel as world wide concerns are spent fuel of uranium and plutonium and in some cases using recycled minor actinide (MA). Those fuel schemes are used for improving an optimum nuclear fuel utilization as well to reduce the radioactive waste from spent fuels. A closed-cycle analysis of all heavy metals on water-cooled cases for both uranium and thorium fuel cycles has been investigated to evaluate the criticality condition, breeding performances, uranium or thorium utilization capability and void reactivity condition. Water-cooled reactor is used for the basic design study including light water and heavy water-cooled as an established technology as well as commercialized nuclear technologies. A developed coupling code of equilibrium fuel cycle burnup code and cell calculation of SRAC code are used for optimization analysis with JENDL 3.3 as nuclear data library. An equilibrium burnup calculation is adopted for estimating an equilibrium state condition of nuclide composition and cell calculation is performed for calculating microscopic neutron cross-sections and fluxes in relation to the effect of different fuel compositions, different fuel pin types and moderation ratios. The sensitivity analysis such as criticality, breeding performance, and void reactivity are strongly depends on moderation ratio and each fuel case has its trend as a function of moderation ratio. Heavy water coolant shows better breeding performance compared with light water coolant, however, it obtains less negative or more positive void reactivity. Equilibrium nuclide compositions are also evaluated to show the production of main nuclides and also to analyze the isotopic composition pattern especially

ATBR - a thorium breeder reactor concept for an early induction of thorium

International Nuclear Information System (INIS)

Jagannathan, V.; Pal, Usha; Karthikeyan, R.; Ganesan, S.; Jain, R.P.; Kamat, S.U.

1999-07-01

A new reactor concept has been proposed for induction of thorium in an enriched uranium reactor. The neutronic characteristics of the fissile and fertile materials, have been exploited to arrive at optimal fuel assembly and core configurations. Each fuel assembly consists of an enriched uranium seed zone and a thoria blanket zone. They are in the form, of ring type fuel clusters. The fuel is contained in vertical pressure tubes placed in a hexagonal lattice array in D 2 O moderator. Boiling H 2 O coolant is used. The 235 U enrichment is about 5%. The thoria rods contain the 233 U bred in situ by irradiation of one batch load of mere thoria clusters (without the seed zone) for one fuel cycle in the same reactor. There is no need for external feed enrichment in thoria rods. Additionally some moveable thoria clusters are used for the purpose of xenon over-ride. The fissile production rate from the fertile material and the consumption rate of fissile inventory is judiciously balanced by the choice of U/Th fuel rod dia, the number and location of thoria rods in the fuel assembly and in the core. During steady state operation at rated power level, there in no need for any conventional control maneuvers such as change in soluble boron concentration or control rod movement as a function of burnup. Burnable poison rods are also not required. A very small reactivity fluctuation of ±2 mk in 300 effective full power days of operation is achieved and can be nearly met by coolant inlet enthalpy changes or moveable thoria clusters. Control is required only for cold shutdown of the reactor. The uranium as well as thoria rods achieve a fairly high burnup of 30-35 GWD/T at the time of discharge. Since the excess reactivity for hot full power operation is nearly zero at all time during the fuel cycle and since the coefficients of reactivity due to temperature and density variations of coolant are nearly zero by design, there is hardly any possibility of severe accidents involving

Molten salt reactor concept

International Nuclear Information System (INIS)

Sood, D.D.

1980-01-01

Molten salt reactor is an advanced breeder concept which is suited for the utilization of thorium for nuclear power production. This reactor is based on the use of solutions of uranium or plutonium fluorides in LiF-BeF 2 -ThF 4 as fuel. Unlike the conventional reactors, no external coolant is used in the reactor core and the fuel salt itself is circulated through heat exchangers to transfer the fission produced heat to a secondary salt (NaF-NaBF 4 ) for steam generation. A part of the fuel stream is continuously processed to isolate 233 Pa, so that it can decay to fissile 233 U without getting converted to 234 Pa, and for the removal of neutron absorbing fission products. This on-line processing scheme makes this reactor concept to achieve a breeding ratio of 1.07 which is the highest for any thermal breeder reactor. Experimental studies at the Bhabha Atomic Research Centre, Bombay, have established the use of plutonium as fuel for this reactor. This molten salt reactor concept is described and the work conducted at the Bhabha Atomic Research Centre is summarised. (auth.)

Breeding and plutonium characterization analysis on actinides closed water-cooled thorium reactor

International Nuclear Information System (INIS)

Permana, Sidik; Sekimoto, Hiroshi; Takaki, Naoyuki

2009-01-01

Higher difficulties (barrier) or more complex design of nuclear weapon, material fabrication and handling and isotopic enrichment can be achieved by a higher isotopic barrier. The isotopic material barrier includes critical mass, heat-generation rate, spontaneous neutron generation and radiation. Those isotopic barriers in case of plutonium isotope is strongly depend on the even mass number of plutonium isotope such as 238 Pu, 240 Pu and 242 Pu and for 233 U of thorium cycle depends on 232 U. In this present study, fuel sustainability as fuel breeding capability and plutonium characterization as main focus of proliferation resistance analysis have been analyzed. Minor actinide (MA) is used as doping material to be loaded into the reactors with thorium fuel. Basic design parameters are based on actinide closed-cycle reactor cooled by heavy water. The evaluation use equilibrium burnup analysis coupled with cell calculation of SRAC and nuclear data library is JENDL.32. Parametrical survey has been done to analyze the effect of MA doping rate, different moderation ratio for several equilibrium burnup cases. Plutonium characterization which based on plutonium isotope composition is strongly depending on MA doping concentration and different moderation conditions. Breeding condition can be achieved and high proliferation resistance level can be obtained by the present reactor systems. Higher isotopic plutonium composition of Pu-238 (more than 40%) can be obtained compared with other plutonium isotopes. In addition, higher moderation ratio gives the isotope composition of 238 Pu increases, however, it obtains lower composition when MA doping is increased and it slightly lower composition for higher burnup. Meanwhile, higher 240 Pu composition can be achieved by higher MA doping rate as well as for obtaining higher breeding capability. (author)

Molten salt reactors

International Nuclear Information System (INIS)

Bouchter, J.C.; Dufour, P.; Guidez, J.; Simon, N.; Renault, C.

2014-01-01

Molten salt reactors are one of the 6 concepts retained for the 4. generation of nuclear reactors. The principle of this reactor is very innovative: the nuclear fuel is dissolved in the coolant which allows the online reprocessing of the fuel and the online recovery of the fission products. A small prototype: the Molten Salt Reactor Experiment (MSRE - 8 MWt) was operating a few years in the sixties in the USA. The passage towards a fast reactor by the suppression of the graphite moderator leads to the concept of Molten Salt Fast Reactor (MSFR) which is presently studied through different European projects such as MOST, ALISIA and EVOL. Worldwide the main topics of research are: the adequate materials resisting to the high level of corrosiveness of the molten salts, fuel salt reprocessing, the 3-side coupling between neutron transport, thermohydraulics and thermo-chemistry, the management of the changing chemical composition of the salt, the enrichment of lithium with Li 7 in the case of the use of lithium fluoride salt and the use of MSFR using U 233 fuel (thorium cycle). The last part of the article presents a preliminary safety analysis of the MSFR. (A.C.)

Thorium Molten Salt Nuclear Energy Synergetic System (THORIMS-NES)

International Nuclear Information System (INIS)

Yoshioka, Ritsuo; Mitachi, Koshi

2013-01-01

The authors have been promoting nuclear energy technology based on thorium molten salt as Thorium Molten Salt Nuclear Energy Synergetic System (THORIMS-NES). This system is a combination of fission power reactor of Molten Salt Reactor (MSR), and Accelerator Molten Salt Breeder (AMSB) for production of fissile 233 U with connecting chemical processing facility. In this paper, concept of THORIMS-NES, advantages of thorium and molten salt recent MSR design results such as FUJI-U3 using 233 U fuel, FUJI-Pu, large sized super-FUJI, pilot plant miniFUJI, AMSB, and chemical processing facility are described. (author)

Studies on the feasibility of the LWRs waste-thorium in-core fuel cycle in the Gas Turbine-Modular Helium Reactor

International Nuclear Information System (INIS)

Talamo, Alberto

2006-01-01

The capability to operate on LWRs waste constitutes one of the major benefits of the Gas Turbine-Modular Helium Reactor; in this paper, it has been evaluated the possibility to incinerate the LWRs waste and to simultaneously breed fissile 233 U by fertile thorium. Since a mixture of pure 239 Pu-thorium has shown a quite poor neutron economy, the LWRs waste-thorium fuel performance has been also tested when plutonium and thorium are allocated in different TRISO particles. More precisely, when fissile and fertile actinides share the same TRISO kernel, the resonance at 0.29eV of the fission and capture microscopic cross sections of 239 Pu diminishes also the absorption rate of fertile 232 Th and thus it degrades the breeding process. Consequently, in the present studies, two different types of fuel have been utilized: the Driver Fuel, made of LWRs waste, and the Transmutation Fuel, made of fertile thorium. Since, in the thermal neutron energy range, the microscopic capture cross section of 232 Th is about 80-100 times smaller than the fission one of 239 Pu, setting thorium in particles with a large kernel and LWRs waste in particles with a small one makes the volume integrated reaction rates better equilibrated. At the light of the above consideration, which drives to load as much thorium as possible, for the Transmutation Fuel they have been selected the JAERI TRISO particles packed 40%; whereas, for the Driver Fuel they have been tested different packing fractions and kernel radii. Since no configuration allowed the reactor to work, the above procedure has been repeated when fertile particles are packed 20%; the latter choice permits over one year of operation, but the build up of 233 U represents only a small fraction of the depleted 239 Pu. Finally, the previous configuration has been also investigated when the fertile and fissile fuels share the same kernel or when the fertile fuel axially alternates with the fissile one. (author)

Present state and perspective of research on thorium cycle

International Nuclear Information System (INIS)

Kimura, Itsuro

1994-01-01

For the prosperity of Japan and the welfare of mankind in the world, enormous quantity of energy is required in 21st century, and the general circumstances of energy and nuclear power are described. In addition to the present nuclear power using mostly 235 U and the plutonium produced from 238 U, it is the thorium cycle that 233 U produced from the third nuclear fuel, thorium, is used for electric power generation as an energy source. In this report, the 'General research on thorium cycle as a promising energy source in and after 21st century' is outlined, which has been advanced by accepting the subsidy of scientific research expense of the Ministry of Education. The features of the thorium cycle and the nuclear data and the nuclear characteristics in comparison with uranium-plutonium reactors are described. The trend of the research and development in the world and in Japan is reported. Two general researches were carried out for five years from fiscal year 1988 to 1992 on the thorium cycle. The results of the research on the nuclear data, the design of thorium reactors, the criticality experiment and analysis, thorium hybrid, thorium fuel, molten salt, fuel reprocessing and radiation safety are reported. (K.I.)

Validation of main nuclear libraries used in thorium reactors using the Serpent code

International Nuclear Information System (INIS)

Faga, Lucas J.

2017-01-01

The purpose of this work is to validate the library of the Serpent standard database for systems containing U-233, U-235, Th-232, Pu-239 and Pu-240. The project will support the other projects of the newly created study group of Nuclear Engineering Center (CEN) of Instituto de Pesquisas Energéticas e Nucleares (IPEN), linked to the study of several types of reactors and their application in thorium cycles, a subject that gains more and more visibility, due to strong and potential promises of energy revolution. The results obtained at the end of the simulations were satisfactory, with the multiplication factors being effective close to 100 PCM of the values provided by the benchmarks, as expected for a validated library. The minimum distance between these values was 2 PCM and the maximum of 280 PCM. The final analysis demonstrates that the ENDF / B-VII library has validated nuclear data for the isotopes of interest and may be used in future thorium study group projects

Uranium production in thorium/denatured uranium fueled PWRs

International Nuclear Information System (INIS)

Arthur, W.B.

1977-01-01

Uranium-232 buildup in a thorium/denatured uranium fueled pressurized water reactor, PWR(Th), was studied using a modified version of the spectrum-dependent zero dimensional depletion code, LEOPARD. The generic Combustion Engineering System 80 reactor design was selected as the reactor model for the calculations. Reactors fueled with either enriched natural uranium and self-generated recycled uranium or uranium from a thorium breeder and self-generated recycled uranium were considered. For enriched natural uranium, concentrations of 232 U varied from about 135 ppM ( 232 U/U weight basis) in the zeroth generation to about 260 ppM ( 232 U/U weight basis) at the end of the fifth generation. For the case in which thorium breeder fuel (with its relatively high 232 U concentration) was used as reactor makeup fuel, concentrations of 232 U varied from 441 ppM ( 232 U/U weight basis) at discharge from the first generation to about 512 ppM ( 232 U/U weight basis) at the end of the fifth generation. Concentrations in freshly fabricated fuel for this later case were 20 to 35% higher than the discharge concentration. These concentrations are low when compared to those of other thorium fueled reactor types (HTGR and MSBR) because of the relatively high 238 U concentration added to the fuel as a denaturant. Excellent agreement was found between calculated and existing experimental values. Nevertheless, caution is urged in the use of these values because experimental results are very limited, and the relevant nuclear data, especially for 231 Pa and 232 U, are not of high quality

New primary energy source by thorium molten-salt reactor technology

International Nuclear Information System (INIS)

Furukawa, Kazuo; Kato, Yoshio; Furuhashi, Akira; Numata, Hiroo; Mitachi, Koushi; Yoshioka, Ritsuo; Sato, Yuzuru; Arakawa, Kazuto

2005-01-01

Among the next 30 years, we have to implement a practical measure in the global energy/environmental problems, solving the followings: (1) replacing the fossil fuels without CO 2 emission, (2) no severe accidents, (3) no concern on military, (4) minimizing wastes, (5) economical, (6) few R and D investment and (7) rapid/huge global application supplying about half of the total primary energy till 50 years later. For this purpose the following system was proposed: THORIMS-NES [Thorium Molten-Salt Nuclear Energy Synergetic System], which is composed of (A) simple fission Molten-Salt power stations (FUJI), and (B) fissile-producing Accelerator Molten-Salt Breeder (AMSB). It has been internationally prepared a practical Developmental Program for its huge-size industrialization of Th breeding fuel cycle to produce a new rational primary energy. Here it is explained the social meaning, the conceptual system design and technological bases, especially, including the molten fluoride salt technology, which was developed as the triple-functional medium for nuclear-engineering, heat-transfer and chemical engineering. The complex function of this system is fully achieved by the simplified facility using a single phase molten-salt only. (author)

Development of fluoride reprocessing technology for molten salt transmutation reactor systems in the Czech Republic

International Nuclear Information System (INIS)

Uhlir, J.; Hosnedl, P.; Matal, O.

2000-01-01

At present, the transmutation of spent nuclear fuel is considered a prospective alternative conception with respect to the current conception based on the non-reprocessed spent fuel disposal into a deep geological repository. The Czech research and development programme in the area of partitioning is directed primarily on the development of the fuel cycle technology for the accelerator - driven subcritical reactor with a liquid fuel based on fluoride melts. The final objective of the research programme is the development of pyrochemical technologies suitable for a continuous or semi-continuous separation process which would allow practically perfect utilization of the transmutation potentialities of the reactor system. The present research is directed particularly on the development of suitable fluoride separation methods the target of which is the removal of the uranium component from spent nuclear fuel and on the research of the electro-separation procedures and further on the development of appropriate construction materials and equipment for the technology of fluoride salt melts. (authors)

Thorium and health: state of the art; Thorium et sante: etat de l'art

Energy Technology Data Exchange (ETDEWEB)

Leiterer, A.; Berard, Ph.; Menetrier, F.

2010-07-01

This report reviews data available in the literature on the subject: 'thorium and health'. Thorium is a natural radioactive element of the actinide series. It is widely distributed in the earth's crust and 99% is found as isotope thorium-232. Its various uses are explained by its chemical, physical, and nuclear properties. As a potential nuclear fuel, thorium is still in demonstration in pilot scale reactors. But thorium has already multiple and sometimes unknown industrial uses. Some mass market products are concerned like light bulb. This raises the issue of wastes, and of exposures of workers and public. Environmental exposure via food and drink of the general population is low, where as workers can be exposed to significant doses, especially during ore extraction. Data on bio-monitoring of workers and biokinetic of thorium, in particular those provided by ICRP, are gathered here. Studies on health effects and toxicity of thorium are scarce and mostly old, except outcomes of its previous medical use. Studies on other forms of thorium should be undertaken to provide substantial data on its toxicity. Concerning treatment, Ca-DTPA is the recommended drug even if its efficacy is moderate. LiHOPO molecule shows interesting results in animals, and further research on chelating agents is needed. (authors)

Spectral shift controlled reactors, denatured U-233/thorium cycle

International Nuclear Information System (INIS)

1978-05-01

This paper presents technical and economic data on the SSCR which may be of use in the International Fuel Cycle Evaluation Program to intercompare alternative nuclear systems. Included in this paper are data on the denatured U-233/thorium cycle. This cycle shows a proliferation advantage over more classical thorium fuel cycle (e.g., highly-enriched U-235/thorium or plutonium/thorium) due to the elimination of chemically-separable, concentrated fissile material from unirradiated nuclear fuel. The U-233 is denatured by mixing with depleted uranium to a concentration no greater than 12 w/o. An exogenous source of U-233 is assumed in this paper, since U-233 does not occur in nature and only a limited supply has been produced to date for research and development work

Thorium fuel for light water reactors - reducing proliferation potential of nuclear power fuel cycle

Energy Technology Data Exchange (ETDEWEB)

Galperin, A; Radkowski, A [Ben-Gurion Univ. of the Negev, Beersheba (Israel)

1996-12-01

The proliferation potential of the light water reactor fuel cycle may be significantly reduced by utilization of thorium as a fertile component of the nuclear fuel. The main challenge of Th utilization is to design a core and a fuel cycle, which would be proliferation-resistant and economically feasible. This challenge is met by the Radkowsky Thorium Reactor (RTR) concept. So far the concept has been applied to a Russian design of a 1,000 MWe pressurized water reactor, known as a WWER-1000, and designated as VVERT. The following are the main results of the preliminary reference design: * The amount of Pu contained in the RTR spent fuel stockpile is reduced by 80% in comparison with a VVER of a current design. * The isotopic composition of the RTR-Pu greatly increases the probability of pre-initiation and yield degradation of a nuclear explosion. An extremely large Pu-238 content causes correspondingly large heat emission, which would complicate the design of an explosive device based on RTR-Pu. The economic incentive to reprocess and reuse the fissile component of the RTR spent fuel is decreased. The once-through cycle is economically optimal for the RTR core and cycle. To summarize all the items above: the replacement of a standard (U-based) fuel for nuclear reactors of current generation by the RTR fuel will provide an inherent barrier for nuclear weapon proliferation. This inherent barrier, in combination with existing safeguard measures and procedures is adequate to unambiguously disassociate civilian nuclear power from military nuclear power. * The RTR concept is applied to existing power plants to assure its economic feasibility. Reductions in waste disposal requirements, as well as in natural U and fabrication expenses, as compared to a standard WWER fuel, provide approximately 20% reduction in fuel cycle (authors).

Review of Brazilian activities related to the thorium fuel cycle and production of thorium compounds at IPEN-CNEN/SP

International Nuclear Information System (INIS)

Lainetti, Paulo E.O.; Freitas, Antonio A.; Mindrisz, Ana C.

2013-01-01

The Brazilian's interest in the nuclear utilization of thorium has started in the 50's as a consequence of the abundant occurrence of monazite sands. Since the sixties, IPEN-CNEN/SP has performed some developments related to the thorium fuel cycle. The production and purification of thorium compounds was carried out at IPEN for about 18 years and the main product was the thorium nitrate with high purity, having been produced over 170 metric tons of this material in the period, obtained through solvent extraction. The thorium nitrate was supplied to the domestic industry and used for gas portable lamps (Welsbach mantle). Although the thorium compounds produced have not been employed in the nuclear area, several studies were conducted. Therefore, those activities and the accumulated experience are of strategic importance, on one hand due to huge Brazilian thorium reserves, on the other hand by the resurgence of the interest of thorium for the Generation IV Advanced Reactors. This paper presents a review of the Brazilian research and development activities related to thorium technology. (author)

Small molten-salt reactors with a rational thorium fuel-cycle

International Nuclear Information System (INIS)

Furukawa, Kazuo; Mitachi, Kohshi; Kato, Yoshio

1992-01-01

In the fission-energy utilization for solving global social and environmental problems including the 'Greenhouse Effect' in the next century, a new strategy should be introduced considering high safety and economy, simplicity, size-flexibility, anti-nuclear proliferation and terrorism, high temperature heat supply, etc., aiming to establish a rational breeding fuelcycle. Thorium Molten-Salt Nuclear Energy Synergetics based on [I] Th utilization, [II] fluid-fuel concept and [III] separation of fissile breeding and power generation functions would be one of the most promising approach. A design study of a standard Molten-Salt Reactor: FUJI-II (350 MWth, 155-161 MWe) ensuring fuel self-sustaining nature (conversion-ratio ∝ 1.0) in spite of small-size, and pilot-plant miniFUJI-II has been proceeded. (orig.)

Simulation an Accelerator driven Subcritical Reactor core with thorium fuel

International Nuclear Information System (INIS)

Shirmohammadi, L.; Pazirandeh, A.

2011-01-01

The main purpose of this work is simulation An Accelerator driven Subcritical core with Thorium as a new generation nuclear fuel. In this design core , A subcritical core coupled to an accelerator with proton beam (E p =1 GeV) is simulated by MCNPX code .Although the main purpose of ADS systems are transmutation and use MA (Minor Actinides) as a nuclear fuel but another use of these systems are use thorium fuel. This simulated core has two fuel assembly type : (Th-U) and (U-Pu) . Consequence , Neutronic parameters related to ADS core are calculated. It has shown that Thorium fuel is use able in this core and less nuclear waste ,Although Iran has not Thorium reserves but study on Thorium fuel cycle can open a new horizontal in use nuclear energy as a clean energy and without nuclear waste

Coupling NMR with Synchrotron radiation at high temperature for the study of molten fluorides : applied to zirconium fluorides

International Nuclear Information System (INIS)

Maksoud, Louis

2013-01-01

Molten fluorides are used in Molten Salt Reactors MSR such as the non moderated fast reactor MSFR, where the molten salt LiF-ThF 4 is the fuel and the coolant. The formation of fission products (FP) such as lanthanides, during the reactor operation, possibly modifies the physicochemical properties of the melt. It is therefore important to characterize the melt from the structural and the dynamics point of view in order to determine its properties. Because of problems related to the radioactivity of thorium, as well as requirements related to spectroscopic methods, the system studied in this thesis is the LiF-ZrF 4 -LaF 3 (zirconium and lanthanum are possible FP). The approach followed in this thesis combines measurements by NMR spectroscopy and EXAFS at 850 C with molecular dynamics simulations. In the molten salt, we have shown the existence of zirconium and lanthanum complexes with different coordination numbers, whose proportions depend on the composition. Depending on the content of ZrF 4 , [ZrF 7 ] 3- species are dominant but change slightly and are further connected between each other's via bridging fluorine. The addition of LaF 3 to the mixture stabilizes the 7 coordination number around the zirconium and tends to enrich the environment of lanthanum with fluorides. A medium-range order is established between the various complexes containing zirconium and lanthanum due to bridging fluorine. Species dynamics is slower when the amount of either ZrF 4 or LaF 3 is higher. We noted a significant effect on the structure and dynamics of species starting 10 mol% LaF 3 added to the medium. The data obtained by this novel approach concerning the chemistry of the molten salt in MSR containing FP, are fundamental to improve the separation of these products and optimize the process. (author)

Verification study of thorium cross section in MVP calculation of thorium based fuel core using experimental data

International Nuclear Information System (INIS)

Mai, V. T.; Fujii, T.; Wada, K.; Kitada, T.; Takaki, N.; Yamaguchi, A.; Watanabe, H.; Unesaki, H.

2012-01-01

Considering the importance of thorium data and concerning about the accuracy of Th-232 cross section library, a series of experiments of thorium critical core carried out at KUCA facility of Kyoto Univ. Research Reactor Inst. have been analyzed. The core was composed of pure thorium plates and 93% enriched uranium plates, solid polyethylene moderator with hydro to U-235 ratio of 140 and Th-232 to U-235 ratio of 15.2. Calculations of the effective multiplication factor, control rod worth, reactivity worth of Th plates have been conducted by MVP code using JENDL-4.0 library [1]. At the experiment site, after achieving the critical state with 51 fuel rods inserted inside the reactor, the measurements of the reactivity worth of control rod and thorium sample are carried out. By comparing with the experimental data, the calculation overestimates the effective multiplication factor about 0.90%. Reactivity worth of the control rods evaluation using MVP is acceptable with the maximum discrepancy about the statistical error of the measured data. The calculated results agree to the measurement ones within the difference range of 3.1% for the reactivity worth of one Th plate. From this investigation, further experiments and research on Th-232 cross section library need to be conducted to provide more reliable data for thorium based fuel core design and safety calculation. (authors)

Reactivity control system of a passively safe thorium breeder pebble bed reactor

International Nuclear Information System (INIS)

Wols, F.J.; Kloosterman, J.L.; Lathouwers, D.; Hagen, T.H.J.J. van der

2014-01-01

Highlights: • A worth of over 15,000 pcm ensures achieving long-term cold shutdown in thorium PBR. • Control rod worth in side reflector is insufficient due to low-power breeder zone. • 20 control rods, just outside the driver zone, can achieve long-term cold shutdown. • BF 3 gas can be inserted for reactor shutdown, but only in case of emergency. • Perturbation theory accurately predicts absorber gas worth for many concentrations. - Abstract: This work investigates the neutronic design of the reactivity control system for a 100 MW th passively safe thorium breeder pebble bed reactor (PBR), a conceptual design introduced previously by the authors. The thorium PBR consists of a central driver zone of 100 cm radius, surrounded by a breeder zone with 300 cm outer radius. The fissile content of the breeder zone is low, leading to low fluxes in the radial reflector region. Therefore, a significant decrease of the control rod worth at this position is anticipated. The reactivity worth of control rods in the side reflector and at alternative in-core positions is calculated using different techniques, being 2D neutron diffusion, perturbation theory and more accurate 3D Monte Carlo models. Sensitivity coefficients from perturbation theory provide a first indication of effective control rod positions, while the 2D diffusion models provide an upper limit on the reactivity worth achievable at a certain radial position due to the homogeneous spreading of the absorber material over the azimuthal domain. Three dimensional forward calculations, e.g. in KENO, are needed for an accurate calculation of the total control rod worth. The two dimensional homogeneous calculations indicate that the reactivity worth in the radial reflector is by far insufficient to achieve cold reactor shutdown, which requires a control rod worth of over 15 000 pcm. Three dimensional heterogeneous KENO calculations show that placing 20 control rods just outside the driver channel, between 100 cm

Reactivity control system of a passively safe thorium breeder pebble bed reactor

Energy Technology Data Exchange (ETDEWEB)

Wols, F.J., E-mail: f.j.wols@tudelft.nl; Kloosterman, J.L.; Lathouwers, D.; Hagen, T.H.J.J. van der

2014-12-15

Highlights: • A worth of over 15,000 pcm ensures achieving long-term cold shutdown in thorium PBR. • Control rod worth in side reflector is insufficient due to low-power breeder zone. • 20 control rods, just outside the driver zone, can achieve long-term cold shutdown. • BF{sub 3} gas can be inserted for reactor shutdown, but only in case of emergency. • Perturbation theory accurately predicts absorber gas worth for many concentrations. - Abstract: This work investigates the neutronic design of the reactivity control system for a 100 MW{sub th} passively safe thorium breeder pebble bed reactor (PBR), a conceptual design introduced previously by the authors. The thorium PBR consists of a central driver zone of 100 cm radius, surrounded by a breeder zone with 300 cm outer radius. The fissile content of the breeder zone is low, leading to low fluxes in the radial reflector region. Therefore, a significant decrease of the control rod worth at this position is anticipated. The reactivity worth of control rods in the side reflector and at alternative in-core positions is calculated using different techniques, being 2D neutron diffusion, perturbation theory and more accurate 3D Monte Carlo models. Sensitivity coefficients from perturbation theory provide a first indication of effective control rod positions, while the 2D diffusion models provide an upper limit on the reactivity worth achievable at a certain radial position due to the homogeneous spreading of the absorber material over the azimuthal domain. Three dimensional forward calculations, e.g. in KENO, are needed for an accurate calculation of the total control rod worth. The two dimensional homogeneous calculations indicate that the reactivity worth in the radial reflector is by far insufficient to achieve cold reactor shutdown, which requires a control rod worth of over 15 000 pcm. Three dimensional heterogeneous KENO calculations show that placing 20 control rods just outside the driver channel

Large-scale nuclear energy from the thorium cycle

International Nuclear Information System (INIS)

Lewis, W.B.; Duret, M.F.; Craig, D.S.; Veeder, J.I.; Bain, A.S.

1973-02-01

The thorium fuel cycle in CANDU (Canada Deuterium Uranium) reactors challenges breeders and fusion as the simplest means of meeting the world's large-scale demands for energy for centuries. Thorium oxide fuel allows high power density with excellent neutron economy. The combination of thorium fuel with organic caloporteur promises easy maintenance and high availability of the whole plant. The total fuelling cost including charges on the inventory is estimated to be attractively low. (author) [fr

Development of strong-sense validation benchmarks for the fluoride salt-cooled high-temperature reactor

International Nuclear Information System (INIS)

Blandford, E. D.

2012-01-01

The Fluoride salt-cooled High-temperature Reactor (FHR) is a class of reactor concepts currently under development for the U. S. Dept. of Energy. The FHR is defined as a Generation IV reactor that features low-pressure liquid fluoride salt cooling, coated-particle fuel, a high-temperature power cycle, and fully passive decay heat rejection. Recent experimental work using simulant fluids have been performed to demonstrate key 'proof of principle' FHR concepts and have helped inform the reactor design process. An important element of developing FHR technology is to sufficiently validate the predictive accuracy of the computer codes used to model system response. This paper presents a set of thermal-hydraulics experiments, defined as Strong-Sense Benchmarks (SSB's), which will help establish the FHR validation domain for simulant fluid suitability. These SSB's are more specifically designed to investigate single-phase natural circulation which is the dominant mode of FHR decay heat removal during off-normal conditions. SSB s should be viewed as engineering reference standards and differ from traditional confirmatory experiments in the sense that they are more focused on fundamental physics as opposed to reproducing high levels of physical similarity with the prototypical design. (authors)

Thorium in nuclear fuel

International Nuclear Information System (INIS)

Stankevicius, Alejandro

2012-01-01

We revise the advantages and possible problems on the use of thorium as a nuclear fuel instead of uranium. The following aspects are considered: 1) In the world there are three times more thorium than uranium 2) In spite that thorium in his natural form it is not a fisil, under neutron irradiation, is possible to transform it to uranium 233, a fisil of a high quality. 3) His ceramic oxides properties are superior to uranium or plutonium oxides. 4) During the irradiation the U 233 due to n,2n reaction produce small quantities of U 232 and his decay daughters' bismuth 212 and thallium 208 witch are strong gamma source. In turn thorium 228 and uranium 232 became, in time anti-proliferate due to there radiation intensity. 5) As it is described in here and experiments done in several countries reactors PHWR can be adapted to the use of thorium as a fuel element 6) As a problem we should mentioned that the different steps in the process must be done under strong radiation shielding and using only automatized equipment s (author)

An experimental test facility to support development of the fluoride-salt-cooled high-temperature reactor

International Nuclear Information System (INIS)

Yoder, Graydon L.; Aaron, Adam; Cunningham, Burns; Fugate, David; Holcomb, David; Kisner, Roger; Peretz, Fred; Robb, Kevin; Wilgen, John; Wilson, Dane

2014-01-01

Highlights: • • A forced convection test loop using FLiNaK salt was constructed to support development of the FHR. • The loop is built of alloy 600, and operating conditions are prototypic of expected FHR operation. • The initial test article is designed to study pebble bed heat transfer cooled by FLiNaK salt. • The test facility includes silicon carbide test components as salt boundaries. • Salt testing with silicon carbide and alloy 600 confirmed acceptable loop component lifetime. - Abstract: The need for high-temperature (greater than 600 °C) energy transport systems is significantly increasing as the world strives to improve energy efficiency and develop alternatives to petroleum-based fuels. Liquid fluoride salts are one of the few energy transport fluids that have the capability of operating at high temperatures in combination with low system pressures. The fluoride-salt-cooled high-temperature reactor design uses fluoride salt to remove core heat and interface with a power conversion system. Although a significant amount of experimentation has been performed with these salts, specific aspects of this reactor concept will require experimental confirmation during the development process. The experimental facility described here has been constructed to support the development of the fluoride-salt-cooled high-temperature reactor concept. The facility is capable of operating at up to 700 °C and incorporates a centrifugal pump to circulate FLiNaK salt through a removable test section. A unique inductive heating technique is used to apply heat to the test section, allowing heat transfer testing to be performed. An air-cooled heat exchanger removes added heat. Supporting loop infrastructure includes a pressure control system, a trace heating system, and a complement of instrumentation to measure salt flow, temperatures, and pressures around the loop. The initial experiment is aimed at measuring fluoride-salt heat transfer inside a heated pebble bed

An optimized symbiotic fusion and molten-salt fission reactor system

International Nuclear Information System (INIS)

Blinkin, V.L.; Novikov, V.M.

A symbiotic fusion-fission reactor system which breeds nuclear fuel is discussed. In the blanket of the controlled thermonuclear reactor (CTR) uranium-233 is generated from thorium, which circulates in the form of ThF 4 mixed with molten sodium and beryllium fluorides. The molten-salt fission reactor (MSR) burns up the uranium-233 and generates tritium for the fusion reactor from lithium, which circulates in the form of LiF mixed with BeF 2 and 233 UF 4 through the MSR core. With a CTR-MSR thermal power ratio of 1:11 the system can produce electrical energy and breed fuel with a doubling time of 4-5 years. The system has the following special features: (1) Fuel reprocessing is much simpler and cheaper than for contemporary fission reactors; reprocessing consists simply in continuous removal of 233 U from the salt circulating in the CTR blanket by the fluorination method and removal of xenon from the MSR fuel salt by gas scavenging; the MSR fuel salt is periodically exchanged for fresh salt and the 233 U is then removed from it; (2) Tritium is produced in the fission reactor, which is a much simpler system than the fusion reactor; (3) The CTR blanket is almost ''clean''; no tritium is produced in it and fission fragment activity does not exceed the activity induced in the structural materials; (4) Almost all the thorium introduced into the CTR blanket can be used for producing 233 U

Radkowsky Thorium Fuel Project

International Nuclear Information System (INIS)

Todosow, Michael

2006-01-01

In the early/mid 1990's Prof. Alvin Radkowsky, former chief scientist of the U.S. Naval Reactors program, proposed an alternate fuel concept employing thorium-based fuel for use in existing/next generation pressurized water reactors (PWRs). The concept was based on the use of a 'seed-blanket-unit' (SBU) that was a one-for-one replacement for a standard PWR assembly with a uranium-based central 'driver' zone, surrounded by a 'blanket' zone containing uranium and thorium. Therefore, the SBU could be retrofit without significant modifications into existing/next generation PWRs. The objective was to improve the proliferation and waste characteristics of the current once-through fuel cycle. The objective of a series of projects funded by the Initiatives for Proliferation Prevention program of the U.S. Department of Energy (DOE-IPP) - BNL-T2-0074,a,b-RU 'Radkowsky Thorium Fuel (RTF) Concept' - was to explore the characteristics and potential of this concept. The work was performed under several BNL CRADAs (BNL-C-96-02 and BNL-C-98-15) with the Radkowsky Thorium Power Corp./Thorium Power Inc. and utilized the technical and experimental capabilities in the Former Soviet Union (FSU) to explore the potential of this concept for implementation in Russian pressurized water reactors (VVERs), and where possible, also generate data that could be used for design and licensing of the concept for Western PWRs. The Project in Russia was managed by the Russian Research Center-?'Kurchatov Institute' (RRC-KI), and included several institutes (e.g., PJSC 'Electrostal', NPO 'LUCH' (Podolsk), RIINM (Bochvar Institute), GAN RF (Gosatomnadzor), Kalininskaja NPP (VVER-1000)), and consisted of the following phases: Phase-1 ($550K/$275K to Russia): The objective was to perform an initial review of all aspects of the concept (design, performance, safety, implementation issues, cost, etc.) to confirm feasibility/viability and identify any 'show-stoppers'; Phase-2 ($600K/$300K to Russia

An evaluation of once-through homogeneous thorium fuel cycle for light water reactors

International Nuclear Information System (INIS)

Joo, H. K.; Noh, J. M.; Yoo, J. W.

2002-01-01

The other ways enhancing the economic potential of thorium fuel has been assessed ; the utilization of lower enriched uranium in thorium-uranium fuel, duplex thorium fuel concept, thorium utilization in the mixed core with uranium fuel assembly and thorium blanket utilization in the uranium core. The fuel economics of the proposed ways of thorium fuel increased compared to the previous homogeneous thorium fuel cycle. Compared to uranium fuel cycle, however, they do not show any economic incentives. From the view of proliferation resistance potential, thorium fuel option has the advantage to reduce the inventory of plutonium production. Any of proposed thorium options are less economical than uranium fuel option, the thorium fuel option has the potential to be utilized in the future for the sake of the effective consumption of excessive plutonium and the preparation against the using up of uranium resource

Design and evaluation of a thorium (IV) selective optode

International Nuclear Information System (INIS)

Safavi, Afsaneh; Sadeghi, Marzieh

2006-01-01

A novel optical sensor has been proposed for sensitive determination of thorium (IV) ion in aqueous solutions. The thorium sensing membrane was prepared by incorporating 4-(p-nitrophenyl azo)-pyrocatechol (NAP) as ionophore in the plasticized PVC membrane containing tributyl phosphate (TBP) as plasticizer. The membrane responds to thorium ion by changing color reversibly from yellow to red-brown in glycine buffer solution at pH 3.5. The proposed sensor displays a linear range of 8.66 x 10 -6 -2.00 x 10 -4 M with a limit of detection of 6 x 10 -6 M. The response time of the optode was about 8.8-12.5 min, depending on the concentration of Th (IV) ions. The selectivity of optode to Th (IV) ions in glycine buffer is good. The sensor can readily be regenerated by exposure to a solution mixture of sodium fluoride and 5-sulfosalicylic acid (dihydrate) (0.01 M each). The optode is fully reversible. The proposed optode was applied to the determination of thorium (IV) in environmental water samples

Preliminary Demonstration Reactor Point Design for the Fluoride Salt-Cooled High-Temperature Reactor

Energy Technology Data Exchange (ETDEWEB)

Qualls, A. L. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Betzler, Benjamin R. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Brown, Nicholas R. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Carbajo, Juan [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Greenwood, Michael Scott [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Hale, Richard Edward [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Harrison, Thomas J. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Powers, Jeffrey J. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Robb, Kevin R. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Terrell, Jerry W. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States)

2015-12-01

Development of the Fluoride Salt-Cooled High-Temperature Reactor (FHR) Demonstration Reactor (DR) is a necessary intermediate step to enable commercial FHR deployment through disruptive and rapid technology development and demonstration. The FHR DR will utilize known, mature technology to close remaining gaps to commercial viability. Lower risk technologies are included in the initial FHR DR design to ensure that the reactor can be built, licensed, and operated within an acceptable budget and schedule. These technologies include tristructural-isotropic (TRISO) particle fuel, replaceable core structural material, the use of that same material for the primary and intermediate loops, and tube-and-shell heat exchangers. This report provides an update on the development of the FHR DR. At this writing, the core neutronics and thermal hydraulics have been developed and analyzed. The mechanical design details are still under development and are described to their current level of fidelity. It is anticipated that the FHR DR can be operational within 10 years because of the use of low-risk, near-term technology options.

Preliminary Demonstration Reactor Point Design for the Fluoride Salt-Cooled High-Temperature Reactor

International Nuclear Information System (INIS)

Qualls, A. L.; Betzler, Benjamin R.; Brown, Nicholas R.; Carbajo, Juan; Greenwood, Michael Scott; Hale, Richard Edward; Harrison, Thomas J.; Powers, Jeffrey J.; Robb, Kevin R.; Terrell, Jerry W.

2015-01-01

Development of the Fluoride Salt-Cooled High-Temperature Reactor (FHR) Demonstration Reactor (DR) is a necessary intermediate step to enable commercial FHR deployment through disruptive and rapid technology development and demonstration. The FHR DR will utilize known, mature technology to close remaining gaps to commercial viability. Lower risk technologies are included in the initial FHR DR design to ensure that the reactor can be built, licensed, and operated within an acceptable budget and schedule. These technologies include tristructural-isotropic (TRISO) particle fuel, replaceable core structural material, the use of that same material for the primary and intermediate loops, and tube-and-shell heat exchangers. This report provides an update on the development of the FHR DR. At this writing, the core neutronics and thermal hydraulics have been developed and analyzed. The mechanical design details are still under development and are described to their current level of fidelity. It is anticipated that the FHR DR can be operational within 10 years because of the use of low-risk, near-term technology options.

Comparison of the radiological impacts of thorium and uranium nuclear fuel cycles

International Nuclear Information System (INIS)

Meyer, H.R.; Witherspoon, J.P.; McBride, J.P.; Frederick, E.J.

1982-03-01

This report compares the radiological impacts of a fuel cycle in which only uranium is recycled, as presented in the Final Generic Environmental Statement on the Use of Recycle Plutonium in Mixed Oxide Fuel in Light Water Cooled Reactors (GESMO), with those of the light-water breeder reactor (LWBR) thorium/uranium fuel cycle in the Final Environmental Statement, Light Water Breeder Reactor Program. The significant offsite radiological impacts from routine operation of the fuel cycles result from the mining and milling of thorium and uranium ores, reprocessing spent fuel, and reactor operations. The major difference between the impacts from the two fuel cycles is the larger dose commitments associated with current uranium mining and milling operations as compared to thorium mining and milling. Estimated dose commitments from the reprocessing of either fuel type are small and show only moderate variations for specific doses. No significant differences in environmental radiological impact are anticipated for reactors using either of the fuel cycles. Radiological impacts associated with routine releases from the operation of either the thorium or uranium fuel cycles can be held to acceptably low levels by existing regulations

Thorium based fuel options for the generation of electricity: Developments in the 1990s

International Nuclear Information System (INIS)

2000-05-01

The IAEA has maintained an interest in the thorium fuel cycle and its worldwide utilization within its framework of activities. Periodic reviews have assessed the current status of this fuel cycle, worldwide applications, economic benefits, and perceived advantages with respect to other nuclear fuel cycles. Since 1994, the IAEA convened a number of technical meetings on the thorium fuel cycle and related issues. Between 1995 and 1997 individual contributions on the thorium fuel cycle were elicited from experts from France, Germany, India, Japan, the Russian Federation and the USA. These contributions included evaluations of the status of the thorium fuel cycle worldwide; the new incentives to use thorium due to large stockpiles of plutonium produced in nuclear reactors; new reactor concepts utilizing thorium; strategies for thorium use; and an evaluation of toxicity of the thorium fuel cycle waste compared to that from other fuel cycles. The results of this updated evaluation are summarized in this publication

Performance of a 229Thorium solid-state nuclear clock

International Nuclear Information System (INIS)

Kazakov, G A; Schreitl, M; Winkler, G; Schumm, T; Litvinov, A N; Romanenko, V I; Yatsenko, L P; Romanenko, A V

2012-01-01

The 7.8 eV nuclear isomer transition in 229 thorium has been suggested as a clock transition in a new type of optical frequency standard. Here we discuss the construction of a ‘solid-state nuclear clock’ from thorium nuclei implanted into single crystals transparent in the vacuum ultraviolet range. We investigate crystal-induced line shifts and broadening effects for the specific system of calcium fluoride. At liquid nitrogen temperatures, the clock performance will be limited by decoherence due to magnetic coupling of the thorium nuclei to neighboring nuclear moments, ruling out the commonly used Rabi or Ramsey interrogation schemes. We propose clock stabilization based on a fluorescence spectroscopy method and present optimized operation parameters. Taking advantage of the large number of quantum oscillators under continuous interrogation, a fractional instability level of 10 −19 might be reached within the solid-state approach. (paper)

An assessment of once-through homogeneous thorium fuel economics for light water reactors

International Nuclear Information System (INIS)

Joo, Hyung Kook; Noh, Jae Man; Yoo, Jae Woon

2001-01-01

The fuel economics of an once-through homogeneous thorium fuel concept for PWR was assessed by doing a detailed core analysis. In addition to this, the fuel economics assessment was also performed for two other ways enhancing the economic potential of thorium fuel; thorium utilization in the mixed core with uranium fuel assembly and Duplex thorium fuel concepts. As a results of fuel economics assessment, the thorium fuel cycle does not show any economic incentives in preference to uranium fuel cycle under the 18-months fuel cycle for PWR. However, the utilization of thorium is the mixed core with uranium fuel assembly and Duplex thorium fuel cycle and show superior fuel economics to uranium fuel under the longer fuel cycle scheme. The economic potential of once-through thorium fuel cycle is expected to be increased further by utilizing the Duplex thorium fuel in the mixed core with uranium fuel assembly

Thorium utilization as a Pu-burner: proposal of Plutonium-Thorium Mixed Oxide (PT-MOX) Project

International Nuclear Information System (INIS)

Aizawa, Otohiko

2000-01-01

In this paper, a Pu-Th mixed oxide (PT-MOX) project is proposed for a thorium utilization and a plutonium burning. None of plutonium can be newly produced from PT-MOX fuel, and the plutonium mass of about 1 ton can be consumed with one reactor (total heavy metal assumed: 100 tons) for 1 year. In order to consume plutonium produced from usual Light Water Reactor, it should be better to operate one PT-MOX reactor for three to five Light Water Reactors. (author)

TRISUL- a code for Thorium Reactor Investigations with Segregated Uranium Loading

International Nuclear Information System (INIS)

Jagannathan, V.

2000-09-01

A code called TRISUL has been developed for the fuel cycle studies involving a large-scale utilization of thorium. It has been specially developed for the design studies of a thorium breeder reactor (ATBR) core. In this core, a high rate of breeding of 233 U is achieved by placing the thoria rods in the ambience of high thermal neutron flux, generated by a combination of enriched uranium or an equivalent seed material and D 2 O moderator. The core consists of a number of such seed and blanket type fuel assemblies arranged in a regular hexagonal lattice array surrounded by D 2 O reflector on all sides. At least one batch size of pure thoria clusters without the seed fuel rods are considered to be loaded uniformly in the same core at twice the assembly lattice pitch. TRISUL solves the few group diffusion theory equations by the center- mesh finite difference method. Regular hexagonal or triangular right-prismatic meshes are considered. Since the ATBR core considers boiling light water as coolant, a thermal hydraulic model is incorporated in the TRISUL code to calculate the void or steam fraction as a function of core height in each fuel assembly. The homogenized two group lattice parameters have been generated by the PHANTOM code system for the two types of fuel clusters stated above

Thorium dioxide: properties and nuclear applications

International Nuclear Information System (INIS)

Belle, J.; Berman, R.M.

1984-01-01

This is the sixth book on reactor materials published under sponsorship of the Naval Reactors Office of the United States Department of Energy, formerly the United States Atomic Energy Commission. This book presents a comprehensive compilation of the most significant properties of thorium dioxide, much like the book Uranium Dioxide: Properties and Nuclear Applications presented information on the fuel material used in the Shippingport Pressurized Water Reactor core

Thorium dioxide: properties and nuclear applications

Energy Technology Data Exchange (ETDEWEB)

Belle, J.; Berman, R.M. (eds.)

1984-01-01

This is the sixth book on reactor materials published under sponsorship of the Naval Reactors Office of the United States Department of Energy, formerly the United States Atomic Energy Commission. This book presents a comprehensive compilation of the most significant properties of thorium dioxide, much like the book Uranium Dioxide: Properties and Nuclear Applications presented information on the fuel material used in the Shippingport Pressurized Water Reactor core.

Transmutation Strategy Using Thorium-Reprocessed Fuel ADS for Future Reactors in Vietnam

Directory of Open Access Journals (Sweden)

Thanh Mai Vu

2013-01-01

Full Text Available Nuclear power is believed to be a key to the energy security for a developing country like Vietnam where the power demanding increases rapidly every year. Nevertheless, spent nuclear fuel from nuclear power plants is the source of radiotoxic and proliferation risk. A conceptual design of ADS utilizing thorium fuel as a based fuel and reprocessed fuel as a seed for nuclear waste transmutation and energy production is proposed as one of the clean, safe, and economical solutions for the problem. In the design, 96 seed assemblies and 84 blanket assemblies were inserted into the core to make a heterogeneous subcritical core configuration. Introducing thorium fuel into the core offers an effective way to transmute plutonium and minor actinide (MA and gain energy from this process. Transmutation rate as a function of burnup is estimated using MCNPX 2.7.0 code. Results show that by using the seed-blanket designed ADS, at 40 GWd/t burnup, 192 kg of plutonium and 156 kg of MA can be eliminated. Equivalently, 1  ADS can be able to transmute the transuranic (TRU waste from 2  LWRs. 14 units of ADS would be required to eliminate TRUs from the future reactors to be constructed in Vietnam.

Preliminary Safeguards Assessment for the Pebble-Bed Fluoride High-Temperature Reactor (PB-FHR) Concept

Energy Technology Data Exchange (ETDEWEB)

Disser, Jay; Arthur, Edward; Lambert, Janine

2016-09-01

This report examines a preliminary design for a pebble bed fluoride salt-cooled high temperature reactor (PB-FHR) concept, assessing it from an international safeguards perspective. Safeguards features are defined, in a preliminary fashion, and suggestions are made for addressing further nuclear materials accountancy needs.

Cycle thorium et réacteurs à sel fondu. Exploration du champ des paramètres et des contraintes définissant le "Thorium Molten Salt Reactor"

OpenAIRE

Mathieu , Ludovic

2005-01-01

Producing nuclear energy in order to reduce the anthropic CO2 emission requires major technological advances. Nuclear plants of IVth generation have to respond to several constraints, as safety improvements, fuel breeding and radioactive waste minimization. For this purpose, it seems promising to use Thorium Cycle in Molten Salt Reactors. Studies on this domain have already been carried out. However, the final concept suffered from serious issues and was discontinued. A new reflection on this...

Analysis of the thorium inclusion in the fuel of a fast reactor cooled by lead; Analisis de la inclusion de torio en el combustible de un reactor rapido enfriado por plomo

Energy Technology Data Exchange (ETDEWEB)

Juarez M, L. C.; Francois L, J. L., E-mail: lcjm@ier.unam.mx [UNAM, Facultad de Ingenieria, Departamento de Sistemas Energeticos, Paseo Cuauhnahuac 8532, Col. Progreso, 62550 Jiutepec, Morelos (Mexico)

2017-09-15

In the present work, we first verified a model of the European reactor cooled with lead (ELFR). The calculations were made with the code Monte Carlo serpent 2.27 and the library of cross sections Jeff-3.1. For this verification, three neutron parameters were compared: the evolution of the neutron multiplication factor, the Doppler constant and the effect of the vacuum fraction of the refrigerant, obtaining a good approximation with the reference values. Subsequently, the inclusion of thorium as a fertile material within the fuel was analyzed and the same neutron parameters were compared with the original fuel. The evolution of criticality for the case of thorium fuel differs significantly with respect to that of the original fuel (without thorium); this is due mainly to the breeding of the fissile isotope {sup 233}U. Therefore, is possible to have a longer fuel cycle, favoring the availability factor of the plant, without compromising the performance of the reactor since both the Doppler constant and the effect of the vacuum fraction of the refrigerant show a similar tendency to those of the original fuel, being negative in both cases. (Author)

A study of sodium-cooled fast breeder reactor with thorium blanket for supply of U-233 to high temperature gas cooled reactor

International Nuclear Information System (INIS)

Yoshida, H.; Nishimura, H.; Osugi, T.

1978-08-01

Symbiotic energy system between fast breeder reactor and thermal reactor would have a potential merit for nuclear proliferation problem. And when using HTGR as the thermal reactor in the system, the energy system appears to be promising as an energy system self-sufficient in fuels, which can generate both electricity and high temperature process heat. In the system the fast breeder reactor has to supply sufficient amount of fissile plutonium to keep the reactor going, and also produce U-233 necessary to the associated U-233 fuelled process heat production HTGR. Three types of LMFBR concepts with thorium blanket, conventional homogeneous core LMFBR, and axial and radial parfait heterogeneous core LMFBRs, have been investigated to find out suitable configurations of LMFBR for supply of U-233 to the HTGR with relatively high conversion ratio of 0.85, in the symbiotic energy system between LMFBR and HTGR. The investigation on LMFBR has been made on fuel sufficiency of the system, inherent safety such as sodium-void and Doppler coefficients, and fuel cycle cost. The followings were revealed; (1) Conventional homogeneous core LMFBR with thorium radial blanket well satisfies the condition of fuel sufficiency, if adequate radial blanket thickness is chosen. However, the sodium-void coefficient and fuel cycle cost are inferior to the other concepts. (2) Axial parfait heterogeneous core LMFBR can be regarded as one of the best LMFBR concepts installed in the symbiotic energy system, from the viewpoints of fuel sufficiency, inherent safety and fuel cycle cost. However, further investigations should be needed on reliability and operationability of the concept. (3) Radial parfait heterogeneous core LMFBR seems inadequate as the LMFBR in the system, because the configurations based on this concept does not satisfy plutonium and U-233 breedings, simultaneously. This LMFBR concept, however, has excellent breeding performance in the internal radial blanket. So further

Parametric analyses of single-zone thorium-fueled molten salt reactor fuel cycle options

International Nuclear Information System (INIS)

Powers, J.J.; Worrall, A.; Gehin, J.C.; Harrison, T.J.; Sunny, E.E.

2013-01-01

Analyses of fuel cycle options based on thorium-fueled Molten Salt Reactors (MSRs) have been performed in support of fuel cycle screening and evaluation activities for the United States Department of Energy. The MSR options considered are based on thermal spectrum MSRs with 3 different separations levels: full recycling, limited recycling, and 'once-through' operation without active separations. A single-fluid, single-zone 2250 MWth (1000 MWe) MSR concept consisting of a fuel-bearing molten salt with graphite moderator and reflectors was used as the basis for this study. Radiation transport and isotopic depletion calculations were performed using SCALE 6.1 with ENDF/B-VII nuclear data. New methodology developed at Oak Ridge National Laboratory (ORNL) enables MSR analysis using SCALE, modeling material feed and removal by taking user-specified parameters and performing multiple SCALE/TRITON simulations to determine the resulting equilibrium operating conditions. Parametric analyses examined the sensitivity of the performance of a thorium MSR to variations in the separations efficiency for protactinium and fission products. Results indicate that self-sustained operation is possible with full or limited recycling but once-through operation would require an external neutron source. (authors)

Analysis of the running-in phase of a Passively Safe Thorium Breeder Pebble Bed Reactor

International Nuclear Information System (INIS)

Wols, F.J.; Kloosterman, J.L.; Lathouwers, D.; Hagen, T.H.J.J. van der

2015-01-01

Highlights: • This work analyzes important trends of the running-in phase of a thorium breeder PBR. • Depletion equations are solved for important actinides and a fission product pair. • Breeding U-233 is achieved in 7 years by cleverly adjusting the feed fuel enrichment. • A safety analysis shows the thorium PBR is passively safe during the running-in phase. - Abstract: The present work investigates the running-in phase of a 100 MW th Passively Safe Thorium Breeder Pebble Bed Reactor (PBR), a conceptual design introduced in previous equilibrium core design studies by the authors. Since U-233 is not available in nature, an alternative fuel, e.g. U-235/U-238, is required to start such a reactor. This work investigates how long it takes to converge to the equilibrium core composition and to achieve a net production of U-233, and how this can be accelerated. For this purpose, a fast and flexible calculation scheme was developed to analyze these aspects of the running-in phase. Depletion equations with an axial fuel movement term are solved in MATLAB for the most relevant actinides (Th-232, Pa-233, U-233, U-234, U-235, U-236 and U-238) and the fission products are lumped into a fission product pair. A finite difference discretization is used for the axial coordinate in combination with an implicit Euler time discretization scheme. Results show that a time dependent adjustment scheme for the enrichment (in case of U-235/U-238 start-up fuel) or U-233 weight fraction of the feed driver fuel helps to restrict excess reactivity, to improve the fuel economy and to achieve a net production of U-233 faster. After using U-235/U-238 startup fuel for 1300 days, the system starts to work as a breeder, i.e. the U-233 (and Pa-233) extraction rate exceeds the U-233 feed rate, within 7 years after start of reactor operation. The final part of the work presents a basic safety analysis, which shows that the thorium PBR fulfills the same passive safety requirements as the

Thorium and health: state of the art

International Nuclear Information System (INIS)

Leiterer, A.; Berard, Ph.; Menetrier, F.

2010-01-01

This report reviews data available in the literature on the subject: 'thorium and health'. Thorium is a natural radioactive element of the actinide series. It is widely distributed in the earth's crust and 99% is found as isotope thorium-232. Its various uses are explained by its chemical, physical, and nuclear properties. As a potential nuclear fuel, thorium is still in demonstration in pilot scale reactors. But thorium has already multiple and sometimes unknown industrial uses. Some mass market products are concerned like light bulb. This raises the issue of wastes, and of exposures of workers and public. Environmental exposure via food and drink of the general population is low, where as workers can be exposed to significant doses, especially during ore extraction. Data on bio-monitoring of workers and biokinetic of thorium, in particular those provided by ICRP, are gathered here. Studies on health effects and toxicity of thorium are scarce and mostly old, except outcomes of its previous medical use. Studies on other forms of thorium should be undertaken to provide substantial data on its toxicity. Concerning treatment, Ca-DTPA is the recommended drug even if its efficacy is moderate. LiHOPO molecule shows interesting results in animals, and further research on chelating agents is needed. (authors)

Sustainable thorium nuclear fuel cycles: A comparison of intermediate and fast neutron spectrum systems

International Nuclear Information System (INIS)

Brown, N.R.; Powers, J.J.; Feng, B.; Heidet, F.; Stauff, N.E.; Zhang, G.; Todosow, M.; Worrall, A.; Gehin, J.C.; Kim, T.K.; Taiwo, T.A.

2015-01-01

Highlights: • Comparison of intermediate and fast spectrum thorium-fueled reactors. • Variety of reactor technology options enables self-sustaining thorium fuel cycles. • Fuel cycle analyses indicate similar performance for fast and intermediate systems. • Reproduction factor plays a significant role in breeding and burn-up performance. - Abstract: This paper presents analyses of possible reactor representations of a nuclear fuel cycle with continuous recycling of thorium and produced uranium (mostly U-233) with thorium-only feed. The analysis was performed in the context of a U.S. Department of Energy effort to develop a compendium of informative nuclear fuel cycle performance data. The objective of this paper is to determine whether intermediate spectrum systems, having a majority of fission events occurring with incident neutron energies between 1 eV and 10 5 eV, perform as well as fast spectrum systems in this fuel cycle. The intermediate spectrum options analyzed include tight lattice heavy or light water-cooled reactors, continuously refueled molten salt reactors, and a sodium-cooled reactor with hydride fuel. All options were modeled in reactor physics codes to calculate their lattice physics, spectrum characteristics, and fuel compositions over time. Based on these results, detailed metrics were calculated to compare the fuel cycle performance. These metrics include waste management and resource utilization, and are binned to accommodate uncertainties. The performance of the intermediate systems for this self-sustaining thorium fuel cycle was similar to a representative fast spectrum system. However, the number of fission neutrons emitted per neutron absorbed limits performance in intermediate spectrum systems

Sustainable thorium nuclear fuel cycles: A comparison of intermediate and fast neutron spectrum systems

Energy Technology Data Exchange (ETDEWEB)

Brown, N.R., E-mail: nbrown@bnl.gov [Brookhaven National Laboratory, Upton, NY (United States); Powers, J.J. [Oak Ridge National Laboratory, Oak Ridge, TN (United States); Feng, B.; Heidet, F.; Stauff, N.E.; Zhang, G. [Argonne National Laboratory, Argonne, IL (United States); Todosow, M. [Brookhaven National Laboratory, Upton, NY (United States); Worrall, A.; Gehin, J.C. [Oak Ridge National Laboratory, Oak Ridge, TN (United States); Kim, T.K.; Taiwo, T.A. [Argonne National Laboratory, Argonne, IL (United States)

2015-08-15

Highlights: • Comparison of intermediate and fast spectrum thorium-fueled reactors. • Variety of reactor technology options enables self-sustaining thorium fuel cycles. • Fuel cycle analyses indicate similar performance for fast and intermediate systems. • Reproduction factor plays a significant role in breeding and burn-up performance. - Abstract: This paper presents analyses of possible reactor representations of a nuclear fuel cycle with continuous recycling of thorium and produced uranium (mostly U-233) with thorium-only feed. The analysis was performed in the context of a U.S. Department of Energy effort to develop a compendium of informative nuclear fuel cycle performance data. The objective of this paper is to determine whether intermediate spectrum systems, having a majority of fission events occurring with incident neutron energies between 1 eV and 10{sup 5} eV, perform as well as fast spectrum systems in this fuel cycle. The intermediate spectrum options analyzed include tight lattice heavy or light water-cooled reactors, continuously refueled molten salt reactors, and a sodium-cooled reactor with hydride fuel. All options were modeled in reactor physics codes to calculate their lattice physics, spectrum characteristics, and fuel compositions over time. Based on these results, detailed metrics were calculated to compare the fuel cycle performance. These metrics include waste management and resource utilization, and are binned to accommodate uncertainties. The performance of the intermediate systems for this self-sustaining thorium fuel cycle was similar to a representative fast spectrum system. However, the number of fission neutrons emitted per neutron absorbed limits performance in intermediate spectrum systems.

Environmental control technology for mining, milling, and refining thorium

International Nuclear Information System (INIS)

Weakley, S.A.; Blahnik, D.E.; Young, J.K.; Bloomster, C.H.

1980-02-01

The purpose of this report is to evaluate, in terms of cost and effectiveness, the various environmental control technologies that would be used to control the radioactive wastes generated in the mining, milling, and refining of thorium from domestic resources. The technologies, in order to be considered for study, had to reduce the radioactivity in the waste streams to meet Atomic Energy Commission (10 CFR 20) standards for natural thorium's maximum permissible concentration (MPC) in air and water. Further regulatory standards or licensing requirements, either federal, state, or local, were not examined. The availability and cost of producing thorium from domestic resources is addressed in a companion volume. The objectives of this study were: (1) to identify the major waste streams generated during the mining, milling, and refining of reactor-grade thorium oxide from domestic resources; and (2) to determine the cost and levels of control of existing and advanced environmental control technologies for these waste streams. Six potential domestic deposits of thorium oxide, in addition to stockpiled thorium sludges, are discussed in this report. A summary of the location and characteristics of the potential domestic thorium resources and the mining, milling, and refining processes that will be needed to produce reactor-grade thorium oxide is presented in Section 2. The wastes from existing and potential domestic thorium oxide mines, mills, and refineries are identified in Section 3. Section 3 also presents the state-of-the-art technology and the costs associated with controlling the wastes from the mines, mills, and refineries. In Section 4, the available environmental control technologies for mines, mills, and refineries are assessed. Section 5 presents the cost and effectiveness estimates for the various environmental control technologies applicable to the mine, mill, and refinery for each domestic resource

Technology of thorium concentrates purification and their transformation in pure nuclear products

International Nuclear Information System (INIS)

Ikuta, A.

1977-01-01

An experimental study for the purification of thorium concentrates by solvent extraction is presented. The product of purification is appropriate for utilization in the fabrication of nuclear reactor fuel elements. The experiments are carried out in a laboratory scale and the following operations are studied: dissolution, extraction-scrubbing, stripping-scrubbing, thorium oxalate precipitation, and thorium nitrate coagulation [pt

Evaluation of U-Zr hydride fuel for a thorium fuel cycle in an RTR concept

Energy Technology Data Exchange (ETDEWEB)

Lee, Kyung Taek; Cho, Nam Zin [Korea Advanced Institute of Science and Technology, Taejon (Korea, Republic of)

1999-12-31

In this paper, we performed a design study of a thorium fueled reactor according to the design concept of the Radkowsky Thorium Reactor (RTR) and evaluated its overall performance. To enhance its performance and alleviate its problems, we introduced a new metallic uranium fuel, uranium-zirconium hydride (U-ZrH{sub 1.6}), as a seed fuel. For comparison, typical ABB/CE-type PWR based on SYSTEM 80+and standard RTR-type thorium reactor were also studied. From the results of performance analysis, we could ascertain advantages of RTR-type thorium fueled reactor in proliferation resistance, fuel cycle economics, and back-end fuel cycle. Also, we found that enhancement of proliferation resistance and safer operating conditions may be achieved by using the U-ZrH{sub 1.6} fuel in the seed region without additional penalties in comparison with the standard RTR`s U-Zr fuel. 6 refs., 2 figs., 6 tabs. (Author)

Evaluation of U-Zr hydride fuel for a thorium fuel cycle in an RTR concept

Energy Technology Data Exchange (ETDEWEB)

Lee, Kyung Taek; Cho, Nam Zin [Korea Advanced Institute of Science and Technology, Taejon (Korea, Republic of)

1998-12-31

In this paper, we performed a design study of a thorium fueled reactor according to the design concept of the Radkowsky Thorium Reactor (RTR) and evaluated its overall performance. To enhance its performance and alleviate its problems, we introduced a new metallic uranium fuel, uranium-zirconium hydride (U-ZrH{sub 1.6}), as a seed fuel. For comparison, typical ABB/CE-type PWR based on SYSTEM 80+and standard RTR-type thorium reactor were also studied. From the results of performance analysis, we could ascertain advantages of RTR-type thorium fueled reactor in proliferation resistance, fuel cycle economics, and back-end fuel cycle. Also, we found that enhancement of proliferation resistance and safer operating conditions may be achieved by using the U-ZrH{sub 1.6} fuel in the seed region without additional penalties in comparison with the standard RTR`s U-Zr fuel. 6 refs., 2 figs., 6 tabs. (Author)

Design of a homogeneous subcritical nuclear reactor based on thorium with a source of californium 252; Diseno de un reactor nuclear subcritico homogeneo a base de Torio con una fuente de Californio 252

Energy Technology Data Exchange (ETDEWEB)

Delgado H, C. E.; Vega C, H. R. [Universidad Autonoma de Zacatecas, Unidad Academica de Estudios Nucleares, Cipres No. 10, Fracc. La Penuela, 98068 Zacatecas, Zac. (Mexico); Sajo B, L., E-mail: ce_delgado89@hotmail.com [Universidad Simon Bolivar, Laboratorio de Fisica Nuclear, Apdo. 89000, 1080A Caracas (Venezuela, Bolivarian Republic of)

2015-10-15

Full text: One of the energy alternatives to fossil fuels which do not produce greenhouse gases is the nuclear energy. One of the drawbacks of this alternative is the generation of radioactive wastes of long half-life and its relation to the generation of nuclear materials to produce weapons of mass destruction. An option to these drawbacks of nuclear energy is to use Thorium as part of the nuclear fuel which it becomes in U{sup 233} when capturing neutrons, that is a fissile material. In this paper Monte Carlo methods were used to design a homogeneous subcritical reactor based on thorium. As neutron reflector graphite was used. The reactor core is homogeneous and is formed of 70% light water as moderator, 12% of enriched uranium UO{sub 2}(NO{sub 3}){sub 4} and 18% of thorium Th(NO{sub 3}){sub 4} as fuel. To start the nuclear fission chain reaction an isotopic source of californium 252 was used with an intensity of 4.6 x 10{sup 7} s{sup -1}. In the design the value of the effective multiplication factor, whose value turned out k{sub eff} <1 was calculated. Also, the neutron spectra at different distances from the source and the total fluence were calculated, as well as the values of the ambient dose equivalent in the periphery of the reactor. (Author)

Feasible region of design parameters for water cooled thorium breeder reactor

International Nuclear Information System (INIS)

Permana, Sidik; Takaki, Naoyuki; Sekimoto, Hiroshi

2007-01-01

The performances of a light water cooled thorium breeder reactor have been investigated. A feasible region of fresh fuel enrichment and moderator to fuel ratio (MFR) is found to satisfy the constrains of criticality, breeding, and negative void coefficient for several burnups of discharged fuel. The equilibrium fuel cycle burnup calculation has been performed which is coupled with the cell calculation. The MFR is changed to investigate its effect to the breeding capability and void reactivity coefficient profile for different average discharged burnups. For moderated cases, the conversion ratio (CR) decreases with increasing burnup and MFR. The ratio of fissile inventory in equilibrium core to the initial fissile loading (FIR) has the maximum value at certain burnups depending on the MFR and its value increases with the decreasing MFR. Considering to the breeding capability of the reactor, for burnups of equal to 30 GWd/t or higher, the MFR≤0.3 is needed. For the larger MFR and lower burnups, the void reactivity coefficient becomes more negative with an increasing void fraction. The most negative value of the void reactivity coefficient is obtained at MFR=0.3. (author)

Rapid determination of fluoride in uranyl nitrate solution obtained in conversion process of uranium tetrafluoride

International Nuclear Information System (INIS)

Levin, R.; Feldman, R.; Sahar, E.

1976-01-01

In uranium production the conversion of impure uranium tetrafluoride by sodium hydroxide was chosen as a current process. A rapid method for determination of fluoride in uranyl-nitrate solution was developed. The method includes precipitation of uranium as diuranate, separation by centrifugation, and subsequent determination of fluoride in supernate by titration with thorium nitrate. Fluoride can be measured over the range 0.15-2.5 gr/gr U, with accuracy of +-5%, within 15 minutes. (author)

Much cleaner nuclear energy from thorium

International Nuclear Information System (INIS)

Damveld, H.

1998-01-01

In Zaragoza, Spain, an experimental thorium reactor will be built, which can be an alternative for uranium reactors. A brief impression is given of activities in the Netherlands with respect to the so-called Energy Amplifier (EA), which is a combination of a nuclear power plant and an accelerator. EA is the idea of C. Rubbia of CERN in Geneva, Switzerland

Power level effects on thorium-based fuels in pressure-tube heavy water reactors

Energy Technology Data Exchange (ETDEWEB)

Bromley, B.P.; Edwards, G.W.R., E-mail: blair.bromley@cnl.ca [Canadian Nuclear Laboratories, Chalk River, Ontario (Canada); Sambavalingam, P. [Univ. of Ontario Inst. of Technology, Oshawa, Ontario (Canada)

2016-06-15

Lattice and core physics modeling and calculations have been performed to quantify the impact of power/flux levels on the reactivity and achievable burnup for 35-element fuel bundles made with Pu/Th or U-233/Th. The fissile content in these bundles has been adjusted to produce on the order of 20 MWd/kg burnup in homogeneous cores in a 700 MWe-class pressure-tube heavy water reactor, operating on a once-through thorium cycle. Results demonstrate that the impact of the power/flux level is modest for Pu/Th fuels but significant for U-233/Th fuels. In particular, high power/flux reduces the breeding and burnup potential of U-233/Th fuels. Thus, there may be an incentive to operate reactors with U-233/Th fuels at a lower power density or to develop alternative refueling schemes that will lower the time-average specific power, thereby increasing burnup.(author)

Power level effects on thorium-based fuels in pressure-tube heavy water reactors

International Nuclear Information System (INIS)

Bromley, B.P.; Edwards, G.W.R.; Sambavalingam, P.

2016-01-01

Lattice and core physics modeling and calculations have been performed to quantify the impact of power/flux levels on the reactivity and achievable burnup for 35-element fuel bundles made with Pu/Th or U-233/Th. The fissile content in these bundles has been adjusted to produce on the order of 20 MWd/kg burnup in homogeneous cores in a 700 MWe-class pressure-tube heavy water reactor, operating on a once-through thorium cycle. Results demonstrate that the impact of the power/flux level is modest for Pu/Th fuels but significant for U-233/Th fuels. In particular, high power/flux reduces the breeding and burnup potential of U-233/Th fuels. Thus, there may be an incentive to operate reactors with U-233/Th fuels at a lower power density or to develop alternative refueling schemes that will lower the time-average specific power, thereby increasing burnup.(author)

Neutronic analysis of the PBMR-400 full core using thorium fuel mixed with plutonium or minor actinides

International Nuclear Information System (INIS)

Acır, Adem; Coşkun, Hasan

2012-01-01

Highlights: ► Neutronic calculations for PBMR 400 were conducted with the computer codes MCNP and MONTEBURNS 2.0. ► The criticality and burnup were investigated for reactor grade plutonium and minor actinides. ► We found that the use of these new fuels in PBMRs would reduce the nuclear waste repository significantly. -- Abstract: Time evolution of criticality and burnup grades of the PBMR were investigated for reactor grade plutonium and minor actinides in the spent fuel of light water reactors (LWRs) mixed with thoria. The calculations were performed by employing the computer codes MCNP and MONTEBURNS 2.0 and using the ENDF/B-V nuclear data library. Firstly, the plutonium–thorium and minor actinides–thorium ratio was determined by using the initial k eff value of the original uranium fuel design. After the selection of the plutonium/minor actinides–thorium mixture ratio, the time-dependent neutronic behavior of the reactor grade plutonium and minor actinides and original fuels in a PBMR-400 reactor was calculated by using the MCNP code. Finally, k eff , burnup and operation time values of the fuels were compared. The core effective multiplication factor (k eff ) for the original fuel which has 9.6 wt.% enriched uranium was computed as 1.2395. Corresponding to this k eff value the reactor grade plutonium/thorium and minor actinide/thorium oxide mixtures were found to be 30%/70% and 50%/50%, respectively. The core lives for the original, the reactor grade plutonium/thorium and the minor actinide/thorium fuels were calculated as ∼3.2, ∼6.5 and ∼5.5 years, whereas, the corresponding burnups came out to be 99,000, ∼190,000 and ∼166,000 MWD/T, respectively, for an end of life k eff set equal to 1.02.

Titanium(IV), zirconium, hafnium and thorium

International Nuclear Information System (INIS)

Brown, Paul L.; Ekberg, Christian

2016-01-01

Titanium can exist in solution in a number of oxidation states. The titanium(IV) exists in acidic solutions as the oxo-cation, TiO 2+ , rather than Ti 4+ . Zirconium is used in the ceramics industry and in nuclear industry as a cladding material in reactors where its reactivity towards hydrolysis reactions and precipitation of oxides may result in degradation of the cladding. In nature, hafnium is found together with zirconium and as a consequence of the contraction in ionic radii that occurs due to the 4f -electron shell, the ionic radius of hafnium is almost identical to that of zirconium. All isotopes of thorium are radioactive and, as a consequence of it being fertile, thorium is important in the nuclear fuel cycle. The polymeric hydrolysis species that have been reported for thorium are somewhat different to those identified for zirconium and hafnium, although thorium does form the Th 4 (OH) 8 8+ species.

Fluoride partitioning R and D programme for molten salt transmutation reactor systems in the Czech Republic

International Nuclear Information System (INIS)

Uhlir, J.; Priman, V.; Vanicek, J.

2001-01-01

The transmutation of spent nuclear fuel is considered a prospective alternative conception to the current conception based on the non-reprocessed spent fuel disposal into underground repository. The Czech research and development programme in the field of partitioning and transmutation is founded on the Molten Salt Transmutation Reactor system concept with fluoride salts based liquid fuel, the fuel cycle of which is grounded on pyrochemical / pyrometallurgical fluoride partitioning of spent fuel. The main research activities in the field of fluoride partitioning are oriented mainly towards technological research of Fluoride Volatility Method and laboratory research on electro-separation methods from fluoride melts media. The Czech national conception in the area of P and T research issues from the national power industry programme and from the Czech Power Company intentions of the extensive utilization of nuclear power in our country. The experimental R and D work is concentrated mainly in the Nuclear Research Institute Rez plc that plays a role of main nuclear research workplace for the Czech Power Company. (author)

Thorium molten-salt nuclear energy synergetics

International Nuclear Information System (INIS)

Furukawa, Kazuo

1989-01-01

One of the most practical and rational approaches for establishing the idealistic Thorium resource utilization program has been presented, which might be effective to solve the principal energy problems, concerning safety, proliferation and terrorism, resource, power size and fuel cycle economy, for the next century. The first step will be the development of Small Molten-Salt Reactors as a flexible power station, which is suitable for early commercialization of Th reactors not necessarily competing with proven Large Solid-Fuel Reactors. Therefore, the more detailed design works and practical R and D planning should be performed under the international cooperations soon, soundly depending on the basic technology established by ORNL already. R and D cost would be surprisingly low. This reactor(MSR) seems to be idealistic not only in power-size, siting, safety, safeguard and economy, but also as an effective partner of Molten-Salt Fissile Breeders(MSB) in order to establish the simplest and economical Thorium molten-salt breeding fuel cycle named THORIMS-NES in all over the world including the developing countries and isolated areas. This would be one of the most practical replies to the Lilienthal's appeal of 'A NEW START' in Nuclear Energy. (author)

Fluoride Salt-Cooled High-Temperature Reactor Technology Development and Demonstration Roadmap

Energy Technology Data Exchange (ETDEWEB)

Holcomb, David Eugene [ORNL; Flanagan, George F [ORNL; Mays, Gary T [ORNL; Pointer, William David [ORNL; Robb, Kevin R [ORNL; Yoder Jr, Graydon L [ORNL

2013-11-01

Fluoride salt-cooled High-temperature Reactors (FHRs) are an emerging reactor class with potentially advantageous performance characteristics, and fully passive safety. This roadmap describes the principal remaining FHR technology challenges and the development path needed to address the challenges. This roadmap also provides an integrated overview of the current status of the broad set of technologies necessary to design, evaluate, license, construct, operate, and maintain FHRs. First-generation FHRs will not require any technology breakthroughs, but do require significant concept development, system integration, and technology maturation. FHRs are currently entering early phase engineering development. As such, this roadmap is not as technically detailed or specific as would be the case for a more mature reactor class. The higher cost of fuel and coolant, the lack of an approved licensing framework, the lack of qualified, salt-compatible structural materials, and the potential for tritium release into the environment are the most obvious issues that remain to be resolved.

Comparative studies of JENDL-3.3, JENDL-3.2, JEFF-3, JEF-2.2 and ENDF/B-6.8 data libraries on the Monte Carlo continuous energy modeling of the gas turbine-modular helium reactor operating with thorium fuels

International Nuclear Information System (INIS)

Talamo, Alberto; Gudowski, Waclaw

2005-01-01

One of the major benefits of the Gas Turbine-Modular Helium Reactor is the capability to operate with several different types of fuel; either Light Water Reactors waste, military plutonium or thorium represent valid candidates as possible types of fuel. In the present studies, we performed a comparison of various nuclear data libraries by the Monte Carlo Continuous Energy Burnup Code MCB applied to the Gas Turbine-Modular Helium Reactor operating on a thorium fuel. A thorium fuel offers valuable attractive advantages: low fuel cost, high reduction of actinides production and the possibility to enable the reactor to act as a breeder of fuel by the neutron capture of fertile 232 Th. We evaluated the possibility to mix thorium with small quantities, about 3% in atomic composition, of 239 Pu, 233 U and 235 U. The mass of thorium must be much larger than that one of plutonium or uranium because of the low capture cross section of thorium compared to the fission one of the fissile nuclides; at the same time, the quantity of the fissile isotopes must grant the criticality condition. These two simultaneous constraints force to load a huge mass of fuel in the reactor; consequently, we propose to allocate the fuel in TRISO particles with a large radius of the kernel. For each of the three different fuels we calculated the evolution of the fuel composition by the MCB code equipped with five different nuclear data libraries: JENDL-3.3, JENDL-3.2, JEFF-3, JEF-2.2 and ENDF/B. (author)

The Thorium-Cycle: safe, abundant power for the new millennium

Science.gov (United States)

Don, May; George, Kim; Peter, Mcintyre; Charles, Meitzler; Robert, Rogers; Akhdior, Sattarov; Mustafa, Yavuz

2001-10-01

A design has been developed for using accelerator-driven thorium fission to produce electric power. A thorium-cycle reactor works by electro-breeding. A pattern of thorium fuel rods is supported in a vessel containing molten lead. A beam of high-energy (1 GeV) protons is targeted in the center of the vessel, and produces a copious flux of energetic neutrons by spallation. The neutrons transmute the thorium nuclei two steps up the periodic table to U233, which fissions rapidly to produce thermal energy. The lead serves as the spallation target, the moderator, and the heat exchange medium to transfer heat from the core to steam exchangers above the core. The thorium cycle has several important advantages over current uranium-cycle fission technology: it is intrinsically stable it cannot melt down; it eats its own waste; it cannot produce bomb-grade isotopes; and there are sufficient thorium reserves to supply the entire Earth’s energy economy for the next millennium. The concept of a thorium-cycle power reactor was first proposed by Rubbia in 1995. Key problems in the original concept were the proton injector (15 MW beam power), reliability of accelerator systems, and parasitic absorption of neutrons by fission products during the life of the core. We have addressed all three problems in a design for a flux-coupled stack of isochronous cyclotrons, delivering a pattern of 7 independent beams to the core. An interdisciplinary collaboration is being formed to develop the concept to a serious design.

Spectrophotometric determination of thorium using arsenazo III in water

International Nuclear Information System (INIS)

Rio, M.A.P. do; Godoy, J.M. de.

1985-01-01

A spectrophotometric determination of thorium with arsenazo III (1,8 dihidroxynaphtaline - 3,6 sulfanic acid - 2,7 bis (azo-2) - phenil argonic acid) was carried out aiming to analyse this element in water. In order to eliminate possible interferences, a coprecipitation with lantanium fluoride was used followed by an extration with 0,2 M TTA (tenoil-trifluor - aceton) / Benzen. The results showed a good agreement with the ones obtained by alfa-spectrometry. (Author) [pt

A review on the status of development in thorium-based nuclear fuels

International Nuclear Information System (INIS)

Lee, Young Woo; Na, S. H.; Lee, Y. W.; Kim, H. S.; Kim, S. H.; Joung, C.Y.

2000-02-01

Thorium as an alternative nuclear energy source had been widely investigated in the 1950s-1960s because it is more abundant than uranium, but the studies of thorium nuclear fuel cycle were discontinued by political and economic reasons in the 1970s. Recently, however, renewed interest was vested in thorium-based nuclear fuel cycle because it may generate less long-lived minor actinides and has a lower radiotoxicity of high level wastes after reprocessing compared with the thorium fuel cycle. In this state-of the art report, thorium-based nuclear cycle. In this state-of the art report, thorium-based nuclear fuel cycle and fuel fabrication processes developed so far with different reactor types are reviewed and analyzed to establish basic technologies of thorium fuel fabrication which could meet our situation. (author)

An Analysis of Testing Requirements for Fluoride Salt Cooled High Temperature Reactor Components

Energy Technology Data Exchange (ETDEWEB)

Holcomb, David Eugene [ORNL; Cetiner, Sacit M [ORNL; Flanagan, George F [ORNL; Peretz, Fred J [ORNL; Yoder Jr, Graydon L [ORNL

2009-11-01

This report provides guidance on the component testing necessary during the next phase of fluoride salt-cooled high temperature reactor (FHR) development. In particular, the report identifies and describes the reactor component performance and reliability requirements, provides an overview of what information is necessary to provide assurance that components will adequately achieve the requirements, and then provides guidance on how the required performance information can efficiently be obtained. The report includes a system description of a representative test scale FHR reactor. The reactor parameters presented in this report should only be considered as placeholder values until an FHR test scale reactor design is completed. The report focus is bounded at the interface between and the reactor primary coolant salt and the fuel and the gas supply and return to the Brayton cycle power conversion system. The analysis is limited to component level testing and does not address system level testing issues. Further, the report is oriented as a bottom-up testing requirements analysis as opposed to a having a top-down facility description focus.

Towards proliferation-resistant thorium fuels

International Nuclear Information System (INIS)

Alhaj, M. Yousif; Mohamed, Nader M.A.; Badawi, Alya; Abou-Gabal, Hanaa H.

2017-01-01

Thorium-plutonium mixture is proposed as alternative nuclear reactor fuel to incinerate the increasing stockpile plutonium. However, this fuel will produce an amount of uranium with about 90% 233U at applicable discharge burnups (60GWD/MTU). This research focuses on proposing an optimum non proliferative thorium fuel, by adding a small amount of 238U to reduce the attractiveness of the resultant uranium. Three types of additive which contain 238U were used: 4.98% enriched, natural and depleted uranium. We found that introducing uranium to the fresh thorium-plutonium fuel reduces its performance even if the uranium was enriched up to 5%. While uranium admixtures reduce the quality of the reprocessed uranium, it also increases the quality of the plutonium. However, this increase is very low compared to the reduced quality of uranium. We also found that using uranium as admixture for thorium-plutonium mixed fuel increases the critical mass of the extracted uranium by a factor of two when using only 1% admixture of uranium. The higher the percentage of uranium admixture the higher the critical mass of the reprocessed one.

Study of electrochemical processes for separation of the actinides and lanthanides in molten fluoride media

International Nuclear Information System (INIS)

Zvejskova, R.; Chuchvalcova Bimova, K.; Lisy, F.; Soucek, P.

2005-01-01

The technology of the Molten Salt Reactors (MSR) is developed for two possible applications: For one thing as the Molten Salt Transmutation Reactor (MSTR) incinerating plutonium and minor actinides within reprocessing of spent fuel from PWR or FBR and for another thing as electricity generating MSR working under thorium uranium fuel cycle. Electrochemical separation processes are one of promising pyrochemical techniques that should enable the on-line reprocessing of circulating fuel salt in MSR (fuel cycle back-end). The former application represents the Czech P and T concept, in which framework the electrolytic separation can be applied both in the front-end and back-end of the MSTR fuel cycle. Within the front-end electro separation should follow the Fluoride Volatility Method (FVM), which should separate 95 % of uranium from the spent fuel in the form of volatile uranium hexafluoride. The residual uranium and fission products (FP) are supposed to be separated among others also by electrochemical methods. The presented work comprises the results reached within development of electrochemical separation of the actinides and fission products from each other by electrolytic deposition method on solid cathode in molten fluoride media, that represent he carrier salts of MSR technology. The knowledge of electrochemical properties (red-ox potentials, mainly of deposition potentials) is necessary for determination of separation possibilities of individual components by electrolysis. (authors)

The evolutionary adoption of thorium beginning with its application in niche LWR fuels

International Nuclear Information System (INIS)

Drera, Saleem

2015-01-01

Since the inception of nuclear energy, the use of thorium as a nuclear fuel has been envisioned. Thorium boasts benefits, however, drawbacks which are both economic and technical including its the lack of a naturally occurring fissile isotope implies that its utility is inherently more difficult. The implementation of thorium as a nuclear fuel requires that it must provide sound technical advantages in combination with attractive economics as compared to standard uranium fuel. Revolutionary thorium concepts such as molten salt reactors and accelerator driven systems may provide theoretical merit, however, their exotic nature and associated technical challenges label them as long-term solutions at best. A near-to-medium term solution for thorium must be based on an evolutionary approach utilizing light/heavy water reactor platforms. While thorium does not provide a near-to-medium term complete replacement of uranium, it does provide substantial benefit within niche applications. To license and bring to market these niche fuels, Thor Energy and an international consortium of entities (including: Fortum, KAERI, Westinghouse, NNL, ITU, IFE, and a few other minor entities) have initiated a fuel development and irradiation test program to characterize the performance of these thoria-containing fuels. (author)

The uranium and thorium separation in the chemical reprocessing of the irradiated fuel of thorium and uranium mixed oxides

International Nuclear Information System (INIS)

Oliveira, E.F. de.

1984-09-01

A bibliographic research has been carried out for reprocessing techniques of irradiated thorium fuel from nuclear reactors. The Thorex/Hoechst process has been specially considered to establish a method for reprocessing thorium-uranium fuel from PWR. After a series of cold tests performed in laboratory it was possible to set the behavior of several parameters affecting the Thorex/Hoechst process. Some comments and suggestions are presented for modifications in the process flosheet conditions. A discussion is carried out for operational conditions such as the aqueous to organic flow ratio the acidity of strip and scrub solutions in the process steps for thorium and uranium recovery. The operation diagrams have been constructed using equilibrium experimental data which correspond to conditions observed in laboratory. (Author) [pt

Heat Transfer in Pebble-Bed Nuclear Reactor Cores Cooled by Fluoride Salts

Science.gov (United States)

Huddar, Lakshana Ravindranath

With electricity demand predicted to rise by more than 50% within the next 20 years and a burgeoning world population requiring reliable emissions-free base-load electricity, can we design advanced nuclear reactors to help meet this challenge? At the University of California, Berkeley (UCB) Fluoride-salt-cooled High Temperature Reactors (FHR) are currently being investigated. FHRs are designed with better safety and economic characteristics than conventional light water reactors (LWR) currently in operation. These reactors operate at high temperature and low pressure making them more efficient and safer than LWRs. The pebble-bed FHR (PB-FHR) variant includes an annular nuclear reactor core that is filled with randomly packed pebble fuel. It is crucial to characterize the heat transfer within this unique geometry as this informs the safety limits of the reactor. The work presented in this dissertation focused on furthering the understanding of heat transfer in pebble-bed nuclear reactor cores using fluoride salts as a coolant. This was done through experimental, analytical and computational techniques. A complex nuclear system with a coolant that has never previously been in commercial use requires experimental data that can directly inform aspects of its design. It is important to isolate heat transfer phenomena in order to understand the underlying physics in the context of the PB-FHR, as well as to make decisions about further experimental work that needs to be done in support of developing the PB-FHR. Certain organic oils can simulate the heat transfer behaviour of the fluoride salt if relevant non-dimensional parameters are matched. The advantage of this method is that experiments can be done at a much lower temperature and at a smaller geometric scale compared to FHRs, thereby lowering costs. In this dissertation, experiments were designed and performed to collect data demonstrating similitude. The limitations of these experiments were also elucidated by

Design study of a PWR of 1.300 MWe of Angra-2 type operating in the thorium cycle

International Nuclear Information System (INIS)

Andrade, E.P.; Carneiro, F.A.N.; Schlosser, G.J.

1984-01-01

The utilization of the thorium-highly enriched uranium and thorium-plutonium mixed oxide fuels in an unmodified PWR is analysed. The PWR of 1300 MWe from KWU (Angra-2 type) is taken as the reference reactor for the study. Reactor core design calculations for both types of fuels considering once-through and recycle fuels. The calculations were performed with the KWU design codes FASER-3 and MEDIUM 2.2 after introduction of the thorium chain and some addition of nuclide data in FASER-3. A two-energy group scheme and a two-dimensional (XY) representation of the reactor core were utilized. (Author) [pt

The use of thorium as an alternative nuclear fuel

International Nuclear Information System (INIS)

Wilson, D.J.

1982-04-01

The use of thorium as an alternative or supplementary nuclear fuel is examined and compared with uranium. A description of various reactor types and their suitability to thorium fuel, and a description of various aspects of the fuel cycle from mining to waste disposal, are included. Comments are made on the safety and economics of each aspect of the fuel cycle and the extension of the lifetime of nuclear fuel

Measurement of europium (III)/europium (II) couple in fluoride molten salt for redox control in a molten salt reactor concept

Science.gov (United States)

Guo, Shaoqiang; Shay, Nikolas; Wang, Yafei; Zhou, Wentao; Zhang, Jinsuo

2017-12-01

The fluoride molten salt such as FLiNaK and FLiBe is one of the coolant candidates for the next generation nuclear reactor concepts, for example, the fluoride salt cooled high temperature reactor (FHR). For mitigating corrosion of structural materials in molten fluoride salt, the redox condition of the salts needs to be monitored and controlled. This study investigates the feasibility of applying the Eu3+/Eu2+ couple for redox control. Cyclic voltammetry measurements of the Eu3+/Eu2+ couple were able to obtain the concentrations ratio of Eu3+/Eu2+ in the melt. Additionally, the formal standard potential of Eu3+/Eu2+ was characterized over the FHR's operating temperatures allowing for the application of the Nernst equation to establish a Eu3+/Eu2+ concentration ratio below 0.05 to prevent corrosion of candidate structural materials. A platinum quasi-reference electrode with potential calibrated by potassium reduction potential is shown as reliable for the redox potential measurement. These results show that the Eu3+/Eu2+ couple is a feasible redox buffering agent to control the redox condition in molten fluoride salts.

Design of a boiling water reactor core based on an integrated blanket-seed thorium-uranium concept

International Nuclear Information System (INIS)

Nunez-Carrera, Alejandro; Francois, Juan Luis; Martin-del-Campo, Cecilia; Espinosa-Paredes, Gilberto

2005-01-01

This paper is concerned with the design of a boiling water reactor (BWR) equilibrium core using thorium as a nuclear material in an integrated blanket-seed (BS) assembly. The integrated BS concept comes from the fact that the blanket and the seed rods are located in the same assembly, and are burned out in a once-through cycle. The idea behind the lattice design is to use the thorium conversion capability in a BWR spectrum, taking advantage of the 233 U build-up. A core design was developed to achieve an equilibrium cycle of 365 effective full power days in a standard BWR with a reload of 104 fuel assemblies designed with an average 235 U enrichment of 7.5 w/o in the seed sub-lattice. The main operating parameters, like power, linear heat generation rate and void distributions were obtained as well as the shutdown margin. It was observed that the analyzed parameters behave like those obtained in a standard BWR. The shutdown margin design criterion was fulfilled by addition of a burnable poison region in the fuel assembly

Basic analysis and comparison among GCFR and LMFBR characteristics in thorium cycle by difusion theory in one energy group

International Nuclear Information System (INIS)

Sabundjian, G.; Ishiguro, Y.

1982-01-01

A preliminary study of the neutronic characteristics of fast of fast breeding reactors with thorium cycle, is done, using models and simplified methods of reactor analysis, aiming to meet an adequate type of breeder reactor with an efficient thorium utilization, that is abundant at Brazil. Basic methods of cross section and reactor calculations are studied, and they are applied for the analysis of GCFRs and LMFBRs breeding characteristics. (E.G.) [pt

Feasibility assessment of the once-through thorium fuel cycle for the PTVM LWR concept

International Nuclear Information System (INIS)

Rachamin, R.; Fridman, E.; Galperin, A.

2015-01-01

Highlights: • The PTVM LWR is an innovation reactor concept operating in a “breed & burn” mode. • An advanced once-through thorium fuel cycle for the PTVM LWR concept is proposed. • The PTVM LWR concept makes use of a seed-blanket geometry. • A novel fuel management scheme based on two separate fuel flow routes is analyzed. • The analysis indicates a potential for utilizing the fuel in an efficient manner. - Abstract: This paper investigates the feasibility of a once-through thorium fuel cycle for the novel reactor-design concept named the pressure tube light water reactor with variable moderator control (PTVM LWR). The PTVM LWR operates in a “breed & burn” mode, which makes it an attractive system for utilizing thorium fuel in a once-through mode. The “breed & burn” mode can emphasize the in situ generation as well as incineration of 233 U, which are the basic foundations of the once-through thorium fuel cycle. The PTVM LWR concept makes use of a seed–blanket geometry, whereby the core is divided into separated regions of thorium-based fuel channel assemblies (blanket) and low-enriched uranium (LEU) based fuel channel assemblies (seed). A novel fuel in-core management scheme based on two separate fuel flow routes (i.e., seed route and blanket route) is proposed and analyzed. Neutronic performance analysis indicates that the proposed novel fuel in-core management scheme has the potential to utilize both LEU- and thorium-based fuel in an efficient manner. The once-through thorium cycle, presented and discussed in this paper, provide interesting research leads and can serve as a bridge between current LEU-based fuel cycles and a thorium fuel cycle based on recycling of 233 U

Assessment of the thorium and uranium fuel cycle in the fast breeder and the high temperature reactor

International Nuclear Information System (INIS)

Schikorr, W.M.

1977-01-01

This report assesses the fissile fuel economy of the uranium and thorium cycle in the advanced reactors currently under development, the fast breeder reactor (FBR) and the high temperature reactor (HTR). It is shown by means of detailed burnup calculations that replacing UO 2 with ThO 2 or Th-metal as the radial blanket breeding material will not have any significant imapct on the breeding and burnup properties of the FBR. A global, analytical investigation is performed to study the fissile fuel economy of the many fissile fuel cycles possible in the HTR. Here it is demonstrated that the optimum conversion ratio of CR 3 O 8 ) demands are evaluated for a country such as the FRG under the assumptions of different future reactor strategy scenarios. Here it is demonstrated that the employement of both HTRs and FBRs can lead to a practically resource independent energy supply system within the next 40 to 60 years. However only through the large scale employement of the fast breeder can the future nuclear resource requirements be assured. (orig.) [de

Advanced Burner Reactor with Breed-and-Burn Thorium Blankets for Improved Economics and Resource Utilization

Energy Technology Data Exchange (ETDEWEB)

Greenspan, Ehud [Univ. of California, Berkeley, CA (United States)

2015-11-04

This study assesses the feasibility of designing Seed and Blanket (S&B) Sodium-cooled Fast Reactor (SFR) to generate a significant fraction of the core power from radial thorium fueled blankets that operate on the Breed-and-Burn (B&B) mode without exceeding the radiation damage constraint of presently verified cladding materials. The S&B core is designed to maximize the fraction of neutrons that radially leak from the seed (or “driver”) into the subcritical blanket and reduce neutron loss via axial leakage. The blanket in the S&B core makes beneficial use of the leaking neutrons for improved economics and resource utilization. A specific objective of this study is to maximize the fraction of core power that can be generated by the blanket without violating the thermal hydraulic and material constraints. Since the blanket fuel requires no reprocessing along with remote fuel fabrication, a larger fraction of power from the blanket will result in a smaller fuel recycling capacity and lower fuel cycle cost per unit of electricity generated. A unique synergism is found between a low conversion ratio (CR) seed and a B&B blanket fueled by thorium. Among several benefits, this synergism enables the very low leakage S&B cores to have small positive coolant voiding reactivity coefficient and large enough negative Doppler coefficient even when using inert matrix fuel for the seed. The benefits of this synergism are maximized when using an annular seed surrounded by an inner and outer thorium blankets. Among the high-performance S&B cores designed to benefit from this unique synergism are: (1) the ultra-long cycle core that features a cycle length of ~7 years; (2) the high-transmutation rate core where the seed fuel features a TRU CR of 0.0. Its TRU transmutation rate is comparable to that of the reference Advanced Burner Reactor (ABR) with CR of 0.5 and the thorium blanket can generate close to 60% of the core power; but requires only one sixth of the reprocessing and

Feasibility study on AFR-100 fuel conversion from uranium-based fuel to thorium-based fuel

Energy Technology Data Exchange (ETDEWEB)

Heidet, F.; Kim, T.; Grandy, C. (Nuclear Engineering Division)

2012-07-30

Although thorium has long been considered as an alternative to uranium-based fuels, most of the reactors built to-date have been fueled with uranium-based fuel with the exception of a few reactors. The decision to use uranium-based fuels was initially made based on the technology maturity compared to thorium-based fuels. As a result of this experience, lot of knowledge and data have been accumulated for uranium-based fuels that made it the predominant nuclear fuel type for extant nuclear power. However, following the recent concerns about the extent and availability of uranium resources, thorium-based fuels have regained significant interest worldwide. Thorium is more abundant than uranium and can be readily exploited in many countries and thus is now seen as a possible alternative. As thorium-based fuel technologies mature, fuel conversion from uranium to thorium is expected to become a major interest in both thermal and fast reactors. In this study the feasibility of fuel conversion in a fast reactor is assessed and several possible approaches are proposed. The analyses are performed using the Advanced Fast Reactor (AFR-100) design, a fast reactor core concept recently developed by ANL. The AFR-100 is a small 100 MW{sub e} reactor developed under the US-DOE program relying on innovative fast reactor technologies and advanced structural and cladding materials. It was designed to be inherently safe and offers sufficient margins with respect to the fuel melting temperature and the fuel-cladding eutectic temperature when using U-10Zr binary metal fuel. Thorium-based metal fuel was preferred to other thorium fuel forms because of its higher heavy metal density and it does not need to be alloyed with zirconium to reduce its radiation swelling. The various approaches explored cover the use of pure thorium fuel as well as the use of thorium mixed with transuranics (TRU). Sensitivity studies were performed for the different scenarios envisioned in order to determine the

Thorium as a substitute for uranium

International Nuclear Information System (INIS)

Hunt, H.

1977-01-01

Reference is made to the paper by E. Teller in Atom, February 1977, who suggested that it appears, at least theoretically, that the use of a thorium cycle in thermal reactors would give enough nuclear fuel for a long time to come, and so avoid the need for using Pu in fast reactors. This appears at first sight to be an attractive proposition, but loses some of this attraction on close examination. Reasons for this are discussed. (U.K.)

Study of the behaviour of some heavy elements in solvents containing hydrogen fluoride

International Nuclear Information System (INIS)

Tarnero, M.

1967-01-01

The anhydrous liquid mixtures: dinitrogen tetroxide-hydrogen fluoride and antimony pentafluoride-hydrogen fluoride were studied as solvents for heavy elements interesting nuclear energy: uranium, thorium, zirconium and for some of their compounds. For N 2 O 4 -HF mixtures, electric conductivity measurements and liquid phase infrared spectra were also obtained. Uranium and zirconium tetrafluoride are much more soluble in N 2 O 4 -HF mixtures than in pure hydrogen fluoride. Uranium dissolved in these mixtures is pentavalent. In SbF 5 -HF mixtures, uranium dissolves with hydrogen evolution and becomes trivalent. The solid compound resulting from the dissolution is a fluoro-antimonate: U(SbF 6 ) 3 . (author) [fr

Analysis on specific nuclear data for reactors physics computations applied to CANDU reactors using thorium-based fuels

International Nuclear Information System (INIS)

Visan, Iuliana E.

2010-01-01

The purpose of this work is to analyze the evaluated nuclear data from ENDF libraries IAEA69 (69 energy groups library) and IAEA172 (172 energy groups library), respectively, in WIMS library format and to represent neutron fission yield, absorption and fission cross-section dependence for 233 Uranium, 232 Thorium isotopes and some actinides of interest on the incident energy. Our interest for these two isotopes is mainly based on the importance of 233 Uranium as 'fissile nucleus' in Thorium-Uranium fuel cycle. Nowadays, nuclear data evaluation for the actinides generated in Thorium-Uranium fuel cycle is seen as a world-wide priority. The fissile nucleus, 233 Uranium 'plays' the same function in Thorium-Uranium fuel cycle as the 235 Uranium in 'the classic' Uranium-Plutonium fuel cycle. As opposed to natural Uranium which contains 0.7 % of the fissile isotope 235 Uranium, natural Thorium doesn't contain fissile isotopes, being composed entirely by the fertile isotope 232 Thorium. Graphical evolutions of interest parameters versus the incident energy are presented. Our interest was also to observe the behavior of these nuclear data for fast, resonance and thermal energy groups, respectively. The ENDF nuclear data libraries are constantly up-dated, so that we can observe an improvement of the IAEA172 library, which disposes of evaluated nuclear data at higher energies (about 20 MeV), as opposed to IAEA69 library (which includes evaluated nuclear data below 10 MeV). Based on our graphical representation, a good agreement between the considered libraries has been observed, sustaining nuclear data validity. (authors)

Investigation on the radiation damage behavior of various alloys in a fusion reactor using thorium molten salt

International Nuclear Information System (INIS)

Ubeyli, Mustafa; Demir, Teyfik

2008-01-01

In fusion reactors, one of the most important problems is the need for the frequent change of the first wall material during the reactor's operation due to the radiation damage induced by high energetic particles, especially fusion neutrons coming from fusion plasma. In order to solve this problem, in HYLIFE-II fusion reactor design, a liquid wall between the fusion plasma and first wall is used. This study presents the radiation damage behaviors of candidate structural materials (9Cr-2WVTa, V-4Cr-4Ti and W-5Re alloys) considered to be used in fusion reactors to determine the optimum thickness of the liquid wall in HYLIFE-II fusion reactor. In the liquid wall, a thorium molten salt consisting of 75%LiF-23%ThF 4 -2% 233 UF 4 was used. Calculations were carried out with respect to the variable liquid wall thickness and for an operation period of 30 years. Numerical results related to atomic displacement and helium generation damage pointed out that the liquid wall thickness should be at least 42, 66 and 81 cm for the materials, W-5Re, 9Cr-2WVTa, V-4Cr-4Ti, respectively in order not to exceed relevant damage limits after a reactor operation of 30 years

Critical review of analytical techniques for safeguarding the thorium-uranium fuel cycle

International Nuclear Information System (INIS)

Hakkila, E.A.

1978-10-01

Conventional analytical methods applicable to the determination of thorium, uranium, and plutonium in feed, product, and waste streams from reprocessing thorium-based nuclear reactor fuels are reviewed. Separations methods of interest for these analyses are discussed. Recommendations concerning the applicability of various techniques to reprocessing samples are included. 15 tables, 218 references

Comparison for thorium fuel cycle facilities of two different capacities for implementation of safeguards

International Nuclear Information System (INIS)

Gangotra, Suresh; Grover, R.B.; Ramakumar, K.L.

2013-01-01

Highlights: • Facilities for implementation of safeguards for thorium fuel cycle have been compared. • Two concepts have been compared. • In one concept, the facilities are designed in hub and spoke concept. • In second concept the facilities are designed as self-contained concept. • The comparison is done on a number of factors, which affect safeguardability and proliferation resistance. -- Abstract: Thorium based nuclear fuel cycle has many attractive features, its inherent proliferation resistance being one of them. This is due to the presence of high energy gamma emitting daughter products of U 232 associated with U 233 . This high energy gamma radiation also poses challenges in nuclear material accounting. A typical thorium fuel cycle facility has a number of plants including a fuel fabrication plant for initial and equilibrium core, a reprocessed U 233 fuel fabrication plant, a reprocessing plant, a fuel assembly/disassembly plant and associated waste handling and management plants. A thorium fuel cycle facility can be set up to serve reactors at a site. Alternatively, one can follow a hub and spoke approach with a large thorium fuel cycle facility acting as a hub, catering to the requirements of reactors at several sites as spokes. These two concepts have their respective merits and shortcomings in terms of engineering and economics. The present paper is aimed at comparing the merits and challenges for implementation of safeguards on the two concepts viz. a large fuel cycle hub catering to reactors at several sites versus a small fuel cycle facility dedicated to reactors at a single site

Comparison for thorium fuel cycle facilities of two different capacities for implementation of safeguards

Energy Technology Data Exchange (ETDEWEB)

Gangotra, Suresh, E-mail: sgangotra@yahoo.co.in; Grover, R.B.; Ramakumar, K.L.

2013-09-15

Highlights: • Facilities for implementation of safeguards for thorium fuel cycle have been compared. • Two concepts have been compared. • In one concept, the facilities are designed in hub and spoke concept. • In second concept the facilities are designed as self-contained concept. • The comparison is done on a number of factors, which affect safeguardability and proliferation resistance. -- Abstract: Thorium based nuclear fuel cycle has many attractive features, its inherent proliferation resistance being one of them. This is due to the presence of high energy gamma emitting daughter products of U{sup 232} associated with U{sup 233}. This high energy gamma radiation also poses challenges in nuclear material accounting. A typical thorium fuel cycle facility has a number of plants including a fuel fabrication plant for initial and equilibrium core, a reprocessed U{sup 233} fuel fabrication plant, a reprocessing plant, a fuel assembly/disassembly plant and associated waste handling and management plants. A thorium fuel cycle facility can be set up to serve reactors at a site. Alternatively, one can follow a hub and spoke approach with a large thorium fuel cycle facility acting as a hub, catering to the requirements of reactors at several sites as spokes. These two concepts have their respective merits and shortcomings in terms of engineering and economics. The present paper is aimed at comparing the merits and challenges for implementation of safeguards on the two concepts viz. a large fuel cycle hub catering to reactors at several sites versus a small fuel cycle facility dedicated to reactors at a single site.

Preliminary concepts: coordinated safeguards for materials management in a thorium--uranium fuel reprocessing plant

International Nuclear Information System (INIS)

Hakkila, E.A.; Barnes, J.W.; Dayem, H.A.; Dietz, R.J.; Shipley, J.P.

1978-10-01

This report addresses preliminary concepts for coordinated safeguards materials management in a typical generic thorium--uranium-fueled light-water reactor (LWR) fuels reprocessing plant. The reference facility is designed to recover thorium and uranium from first-generation (denatured 235 U) startup fuels, first-recycle and equilibrium (denatured 233 U) thorium--uranium LWR fuels, and to recover the plutonium generated in the 238 U denaturant as well. 12 figures, 3 tables

Design of an equilibrium nucleus of a BWR type reactor based in a Thorium-Uranium fuel; Diseno de un nucleo de equilibrio de un reactor tipo BWR basado en un combustible de Torio-Uranio

Energy Technology Data Exchange (ETDEWEB)

Francois, J.L.; Nunez C, A. [Laboratorio de Analisis en Ingenieria de Reactores Nucleares, Facultad de Ingenieria-UNAM, Paseo Cuauhnahuac 8532, Jiutepec, Morelos (Mexico)

2003-07-01

In this work the design of the reactor nucleus of boiling water using fuel of thorium-uranium is presented. Starting from an integral concept based in a type cover-seed assemble is carried out the design of an equilibrium reload for the nucleus of a reactor like that of the Laguna Verde Central and its are analyzed some of the main design variables like the cycle length, the reload fraction, the burnt fuel, the vacuum distribution, the generation of lineal heat, the margin of shutdown, as well as a first estimation of the fuel cost. The results show that it is feasible to obtain an equilibrium reload, comparable to those that are carried out in the Laguna Verde reactors, with a good behavior of those analyzed variables. The cost of the equilibrium reload designed with the thorium-uranium fuel is approximately 2% high that the uranium reload producing the same energy. It is concluded that it is convenient to include burnable poisons, type gadolinium, in the fuel with the end of improving the reload design, the fuel costs and the margin of shutdown. (Author)

Economic analysis of thorium-uranium fuel cycle introduced into PWRs

International Nuclear Information System (INIS)

Fan Li; Sun Qian

2014-01-01

Using PWR of Daya Bay Unit l as the reference reactor, a validated computer code was used to calculate the fuel cycle costs for uranium fuel cycle and thorium-uranium fuel cycle over the following 20 0perational years respectively. The calculation results show that the thorium-uranium fuel cycle is economically competitive with the uranium fuel cycle when reprocessing mode is adopted. For thorium-uranium fuel cycle, if the price of natural uranium is higher than 120 $ /pound U_3O_8, the fuel cycle cost of the direct disposal mode is greater than that of the reprocessing mode. Therefore, when the uranium price may maintain a high level long-termly, adopting reprocessing mode will benefit the economic advantage for the thorium-uranium fuel cycle introduced into PWRs. (authors)

Current status of fluoride volatility method development

Energy Technology Data Exchange (ETDEWEB)

Uhlir, J.; Marecek, M.; Skarohlid, J. [UJV - Nuclear Research Institute, Research Centre Rez, CZ-250 68 Husinec - Rez 130 (Czech Republic)

2013-07-01

The Fluoride Volatility Method is based on a separation process, which comes out from the specific property of uranium, neptunium and plutonium to form volatile hexafluorides whereas most of fission products (mainly lanthanides) and higher transplutonium elements (americium, curium) present in irradiated fuel form nonvolatile tri-fluorides. Fluoride Volatility Method itself is based on direct fluorination of the spent fuel, but before the fluorination step, the removal of cladding material and subsequent transformation of the fuel into a powdered form with a suitable grain size have to be done. The fluorination is made with fluorine gas in a flame fluorination reactor, where the volatile fluorides (mostly UF{sub 6}) are separated from the non-volatile ones (trivalent minor actinides and majority of fission products). The subsequent operations necessary for partitioning of volatile fluorides are the condensation and evaporation of volatile fluorides, the thermal decomposition of PuF{sub 6} and the finally distillation and sorption used for the purification of uranium product. The Fluoride Volatility Method is considered to be a promising advanced pyrochemical reprocessing technology, which can mainly be used for the reprocessing of oxide spent fuels coming from future GEN IV fast reactors.

Flowchart evaluations of irradiated fuel treatment process of low burnup thorium

International Nuclear Information System (INIS)

Linardi, M.

1987-01-01

A literature survey has been carried out, on some versions of the acid-thorex process. Flowsheets of the different parts of the process were evaluated with mixer-settlers experiments. A low burnup thorium fuel (mass ratio Th/U∼100/1), proposed for Brazilian fast breeder reactor initial program, was considered. The behaviour of some fission products was studied by irradiated tracers techniques. Modifications in some of the process parameters were necessary to achieve low losses of 233 U and 232 U and 232 Th. A modified acid-thorex process flowsheet, evaluated in a complete operational cycle, for the treatment of low burnup thorium fuels, is presented. High decontamination factors of thorium in uranium, with reasonable decontamination of uranium in thorium, were achieved. (author) [pt

Uranium-thorium fuel cycle in a very high temperature hybrid system

International Nuclear Information System (INIS)

Hernandez, C.R.G.; Oliva, A.M.; Fajardo, L.G.; Garcia, J.A.R.; Curbelo, J.P.; Abadanes, A.

2011-01-01

Thorium is a potentially valuable energy source since it is about three to four times as abundant as Uranium. It is also a widely distributed natural resource readily accessible in many countries. Therefore, Thorium fuels can complement Uranium fuels and ensure long term sustainability of nuclear power. The main advantages of the use of a hybrid system formed by a Pebble Bed critical nuclear reactor and two Pebble Bed Accelerator Driven Systems (ADSs) using a Uranium-Thorium (U + Th) fuel cycle are shown in this paper. Once-through and two step U + Th fuel cycle was evaluated. With this goal, a preliminary conceptual design of a hybrid system formed by a Graphite Moderated Gas-Cooled Very High Temperature Reactor and two ADSs is proposed. The main parameters related to the neutronic behavior of the system in a deep burn scheme are optimized. The parameters that describe the nuclear fuel breeding and Minor Actinide stockpile are compared with those of a simple Uranium fuel cycle. (author)

Impact of nuclear library difference on neutronic characteristics of thorium-loaded light water reactor fuel

International Nuclear Information System (INIS)

Unesaki, H.; Isaka, S.; Nakagome, Y.

2006-01-01

Impact of nuclear library difference on neutronic characteristics of thorium-loaded light water reactor fuel is investigated through cell burnup calculations using SRAC code system. Comparison of k ∞ and nuclide composition was made between the results obtained by JENDL-3.3, ENDF/B-VI.8 and JEFF3.0 for (U, Th)O 2 fuels as well as UO 2 fuels, with special interest on the burnup dependence of the neutronic characteristics. The impact of nuclear data library difference on k ∞ of (U, Th)O 2 fuels was found to be significantly large compared to that of UO 2 fuels. Notable difference was also found in nuclide concentration of TRU nuclides. (authors)

Design of a heterogeneous subcritical nuclear reactor with molten salts based on thorium

International Nuclear Information System (INIS)

Medina C, D.; Hernandez A, P.; Letechipia de L, C.; Vega C, H. R.; Sajo B, L.

2015-09-01

This paper presents the design of a heterogeneous subcritical nuclear reactor with molten salts based on thorium, with graphite moderator and a 252 Cf source, whose dose levels at the periphery allows its use in teaching and research activities. The design was realized by the Monte Carlo method, where the geometry, dimensions and the fuel was varied in order to obtain the best design. The result was a cubic reactor of 110 cm of side, with graphite moderator and reflector. In the central part having 9 ducts of 3 cm in diameter, eight of them are 110 cm long, which were placed on the Y axis; the separation between each duct is 10 cm. The central duct has 60 cm in length and this contains the 252 Cf source, also there are two irradiation channels and the other six contain a molten salt ( 7 LiF - BeF 2 - ThF 4 - UF 4 ) as fuel. For the design the k eff was calculated, neutron spectra and ambient dose equivalent. In the first instance the above was calculated for a virgin fuel, was called case 1; then a percentage of 233 U was used and the percentage of Th was decreased and was called case 2. This with the purpose of comparing two different fuels operating within the reactor. For the two irradiation ducts three positions are used: center, back and front, in each duct in order to have different flows. (Author)

Uranium and thorium cycles for sodium fast reactors: Neutronic aspects and associated wastes

International Nuclear Information System (INIS)

Brizi, J.

2010-10-01

Sodium fast reactors (SFR-Na) with uranium 238/plutonium 239(U/Pu) cycle, its technical feasibility has already proven, allow to overcome the problem of natural uranium resources in achieving the regeneration of the fuel fissile element. In addition, a waste management can be performed to reduce the radiotoxicity of actinides produced by the reactor in transmuting the AM in the core (homogeneous transmutation). Another alternative to minimize waste is to use another couple fertile-fissile: the thorium 232 and the uranium 233 (Th/U). The comparison is performed on neutronic and safety aspects and on waste production, in using an evolutive Monte Carlo. Although one does not disclose real clear advantages concerning the radiotoxicity of wastes for a particular cycle, the Th/U cycle reduces the radiotoxicity during periods when it is the highest. The homogeneous transmutation minimizes significantly for both cycles, radiotoxicity of wastes, with different factors depending on the considered time period. However, it is done to the detriment of an important increase of AM in the core. If we consider the nuclear stop, the inventory of the reactor core becomes a waste. The gain provided by the transmutation, taking into account both the core and accumulated waste radio-toxicities, will be quantified, and shows the transmutation does not provide a significant gain if the burning of main fissile elements is not considered when the nuclear is stopped. (author)

Nuclear data covariances and sensitivity analysis, validation of a methodology based on the perturbation theory; application to an innovative concept: the molten thorium salt fueled reactor

International Nuclear Information System (INIS)

Bidaud, A.

2005-10-01

Neutron transport simulation of nuclear reactors is based on the knowledge of the neutron-nucleus interaction (cross-sections, fission neutron yields and spectra...) for the dozens of nuclei present in the core over a very large energy range (fractions of eV to several MeV). To obtain the goal of the sustainable development of nuclear power, future reactors must have new and more strict constraints to their design: optimization of ore materials will necessitate breeding (generation of fissile material from fertile material), and waste management will require transmutation. Innovative reactors that could achieve such objectives - generation IV or ADS (accelerator driven system) - are loaded with new fuels (thorium, heavy actinides) and function with neutron spectra for which nuclear data do not benefit from 50 years of industrial experience, and thus present particular challenges. After validation on an experimental reactor using an international benchmark, we take classical reactor physics tools along with available nuclear data uncertainties to calculate the sensitivities and uncertainties of the criticality and temperature coefficient of a thorium molten salt reactor. In addition, a study based on the important reaction rates for the calculation of cycle's equilibrium allows us to estimate the efficiency of different reprocessing strategies and the contribution of these reaction rates on the uncertainty of the breeding and then on the uncertainty of the size of the reprocessing plant. Finally, we use this work to propose an improvement of the high priority experimental request list. (author)

Experiments for quick and accurate thorium assay by means of potentiometric end point determination

International Nuclear Information System (INIS)

Mainka, E.; Coerdt, W.

1978-10-01

Two methods are described which allow quick thorium assay easily to be automated. In the potentiometric titration with NaF the ion sensitive fluoride electrode is used as the indicator. The analysis can be performed for pH values 3 to 4. Th(OH) 4 precipitation must be avoided although the acidity of the solution must not be too high since otherwise erroneous measurements will be obtained. In the complexometric thorium assay EDTA is used for titration and the indicator is the copper sensitive electrode. This method offers the advantage that the analysis can be performed in the presence of large amounts of uranium, which is excluded under the NaF method. (orig.) [de

Fluoride Salt-Cooled High-Temperature Demonstration Reactor Point Design

Energy Technology Data Exchange (ETDEWEB)

Qualls, A. L. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Brown, Nicholas R. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Betzler, Benjamin R. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Carbajo, Juan [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Hale, Richard Edward [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Harrison, Thomas J. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Powers, Jeffrey J. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Robb, Kevin R. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Terrell, Jerry W. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Wysocki, Aaron J. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States)

2016-02-01

The fluoride salt-cooled high-temperature reactor (FHR) demonstration reactor (DR) is a concept for a salt-cooled reactor with 100 megawatts of thermal output (MWt). It would use tristructural-isotropic (TRISO) particle fuel within prismatic graphite blocks. FLiBe (2 LiF-BeF₂) is the reference primary coolant. The FHR DR is designed to be small, simple, and affordable. Development of the FHR DR is a necessary intermediate step to enable near-term commercial FHRs. Lower risk technologies are purposely included in the initial FHR DR design to ensure that the reactor can be built, licensed, and operated within an acceptable budget and schedule. These technologies include TRISO particle fuel, replaceable core structural material, the use of that same material for the primary and intermediate loops, and tube-and-shell primary-to-intermediate heat exchangers. Several preconceptual and conceptual design efforts that have been conducted on FHR concepts bear a significant influence on the FHR DR design. Specific designs include the Oak Ridge National Laboratory (ORNL) advanced high-temperature reactor (AHTR) with 3400/1500 MWt/megawatts of electric output (MWe), as well as a 125 MWt small modular AHTR (SmAHTR) from ORNL. Other important examples are the Mk1 pebble bed FHR (PB-FHR) concept from the University of California, Berkeley (UCB), and an FHR test reactor design developed at the Massachusetts Institute of Technology (MIT). The MIT FHR test reactor is based on a prismatic fuel platform and is directly relevant to the present FHR DR design effort. These FHR concepts are based on reasonable assumptions for credible commercial prototypes. The FHR DR concept also directly benefits from the operating experience of the Molten Salt Reactor Experiment (MSRE), as well as the detailed design efforts for a large molten salt reactor concept and its breeder variant, the Molten Salt Breeder Reactor. The FHR DR technology is most representative of the 3400 MWt AHTR

Arsenic and fluoride removal from groundwater by electrocoagulation using a continuous filter-press reactor.

Science.gov (United States)

Guzmán, Athziri; Nava, José L; Coreño, Oscar; Rodríguez, Israel; Gutiérrez, Silvia

2016-02-01

We investigated simultaneous arsenic and fluoride removal from ground water by electrocoagulation (EC) using aluminum as the sacrificial anode in a continuous filter-press reactor. The groundwater was collected at a depth of 320 m in the Bajío region in Guanajuato Mexico (arsenic 43 µg L(-1), fluoride 2.5 mg L(-1), sulfate 89.6 mg L(-1), phosphate 1.8 mg L(-1), hydrated silica 112.4 mg L(-1), hardness 9.8 mg L(-1), alkalinity 31.3 mg L(-1), pH 7.6 and conductivity 993 µS cm(-1)). EC was performed after arsenite was oxidized to arsenate by addition of 1 mg L(-1) hypochlorite. The EC tests revealed that at current densities of 4, 5 and 6 mA cm(-2) and flow velocities of 0.91 and 1.82 cm s(-1), arsenate was abated and residual fluoride concentration satisfies the WHO standard (CF < 1.5 mg L(-1)). Spectrometric analyses performed on aluminum flocs indicated that these are mainly composed of aluminum-silicates of calcium and magnesium. Arsenate removal by EC involves adsorption on aluminum flocs, while fluoride replaces a hydroxyl group from aluminum aggregates. The best EC was obtained at 4 mA cm(-2) and 1.82 cm s(-1) with electrolytic energy consumption of 0.34 KWh m(-3). Copyright © 2015 Elsevier Ltd. All rights reserved.

Neutron spectra calculation and doses in a subcritical nuclear reactor based on thorium

International Nuclear Information System (INIS)

Medina C, D.; Hernandez A, P. L.; Hernandez D, V. M.; Vega C, H. R.; Sajo B, L.

2015-10-01

This paper describes a heterogeneous subcritical nuclear reactor with molten salts based on thorium, with graphite moderator and a source of 252 Cf, whose dose levels in the periphery allows its use in teaching and research activities. The design was done by the Monte Carlo method with the code MCNP5 where the geometry, dimensions and fuel was varied in order to obtain the best design. The result is a cubic reactor of 110 cm side with graphite moderator and reflector. In the central part they have 9 ducts that were placed in the direction of axis Y. The central duct contains the source of 252 Cf, of 8 other ducts, are two irradiation ducts and the other six contain a molten salt ( 7 LiF - BeF 2 - ThF 4 - UF 4 ) as fuel. For design the k eff , neutron spectra and ambient dose equivalent was calculated. In the first instance the above calculation for a virgin fuel was called case 1, then a percentage of 233 U was used and the percentage of Th was decreased and was called case 2. This with the purpose to compare two different fuels working inside the reactor. In the case 1 a value was obtained for the k eff of 0.13 and case 2 of 0.28, maintaining the subcriticality in both cases. In the dose levels the higher value is in case 2 in the axis Y with a value of 3.31 e-3 ±1.6% p Sv/Q this value is reported in for one. With this we can calculate the exposure time of personnel working in the reactor. (Author)

The future role of thorium in assuring CANDU fuel supplies

International Nuclear Information System (INIS)

Slater, J.B.

1985-01-01

Atomic Energy of Canada Limited (AECL), in partnership with Canadian industry and power utilities, has developed the CANDU reactor as a safe, reliable and economic means of transforming nuclear fuel into useable power. The use of thorium/uranium-233 recycle gives the possibility of a many-fold increase in energy yield over that which can be obtained from the use of uranium in once-through cycles. The neutronic properties of uranium-233 combine with the inherent neutron economy of the CANDU reactor to offer the possibility of near-breeder cycles in which there is no net consumption of fissile material under equilibrium fuelling conditions. Use of thorium cycles in CANDU will limit the impact of higher uranium prices. When combined with the potential for significant reductions in CANDU capital costs, then the long-term prospect is for generating costs near to current levels. Development of thorium cycles in CANDU will safeguard against possible uranium shortages in the next century, and will maintain and continue the commercial viability of CANDU as a long-term energy technology. (author)

Review of problems associated with the utilization of available thorium resources

International Nuclear Information System (INIS)

O'Hara, F.A.; Gray, R.A.

1975-01-01

Portions of the U. S. Thorium Stockpile are in danger of literally ''going to waste.'' These raw materials, with their high concentrations of thorium, are valuable resources which can be utilized to fuel thermal converter reactors. A portion of this stockpile was transferred to Mound Laboratory in the early 1950's. In 1972, the material was determined to be excess to all present and foreseeable future national requirements. Disposal by burial was recommended by the AEC. Following a detailed study of the potential usefulness of the material and the costs associated with land burial, the AEC agreed to offer the material on surplus sale. Risks and benefits associated with retention of the thorium stockpile are described. Nuclear Materials Managers are uniquely situated to exercise influence and direct the future course of remaining thorium reserves

Feasibility of recycling thorium in a fusion-fission hybrid/PWR symbiotic system

International Nuclear Information System (INIS)

Josephs, J.M.

1980-01-01

A study was made of the economic impact of high levels of radioactivity in the thorium fuel cycle. The sources of this radioactivity and means of calculating the radioactive levels at various stages in the fuel cycle are discussed and estimates of expected levels are given. The feasibility of various methods of recycling thorium is discussed. These methods include direct recycle, recycle after storage for 14 years to allow radioactivity to decrease, shortening irradiation times to limit radioactivity build up, and the use of the window in time immediately after reprocessing where radioactivity levels are diminished. An economic comparison is made for the first two methods together with the throwaway option where thorium is not recycled using a mass energy flow model developed for a CTHR (Commercial Tokamak Hybrid Reactor), a fusion fission hybrid reactor which serves as fuel producer for several PWR reactors. The storage option is found to be most favorable; however, even this option represents a significant economic impact due to radioactivity of 0.074 mills/kW-h which amounts to $4 x 10 9 over a 30 year period assuming a 200 gigawatt supply of electrical power

The measurements of critical mass with uranium fuel elements and thorium rods

International Nuclear Information System (INIS)

Yao Zhiquan; Chen Zhicheng; Yao Zewu; Ji Huaxiang; Bao Borong; Zhang Jiahua

1991-01-01

The critical experiments with uranium elements and Thorium rods have been performed in zero power reactor at Shanghai Institute of Nuclear Research. The critical masses have been measured in various U/Th ratios. The fuels are 3% 235 U-enriched uranium. The Thorium rods are made from power of ThF 4 . Ratios of calculated values to experimental values are nearly constant at 0.995

ICP-MS determination of rare earth elements, yttrium, uranium and thorium in niobium-tantalum rich samples

International Nuclear Information System (INIS)

Sunilkumar, Beena; Padmasubashini, V.

2013-01-01

ICP-MS is a powerful and extremely sensitive technique which has been applied successfully for the determination of REEs in diverse geological samples. In the present work, ICP-MS has been applied for the rapid determination of REEs, yttrium as well as uranium and thorium in niobium and tantalum rich samples, using a fluoride fusion method for sample dissolution

Weapons-grade plutonium dispositioning. Volume 3: A new reactor concept without uranium or thorium for burning weapons-grade plutonium

International Nuclear Information System (INIS)

Ryskamp, J.M.; Schnitzler, B.G.; Fletcher, C.D.

1993-06-01

The National Academy of Sciences (NAS) requested that the Idaho National Engineering Laboratory (INEL) examine concepts that focus only on the destruction of 50,000 kg of weapons-grade plutonium. A concept has been developed by the INEL for a low-temperature, low-pressure, low-power density, low-coolant-flow-rate light water reactor that destroys plutonium quickly without using uranium or thorium. This concept is very safe and could be designed, constructed, and operated in a reasonable time frame. This concept does not produce electricity. Not considering other missions frees the design from the paradigms and constraints used by proponents of other dispositioning concepts. The plutonium destruction design goal is most easily achievable with a large, moderate power reactor that operates at a significantly lower thermal power density than is appropriate for reactors with multiple design goals. This volume presents the assumptions and requirements, a reactor concept overview, and a list of recommendations. The appendices contain detailed discussions on plutonium dispositioning, self-protection, fuel types, neutronics, thermal hydraulics, off-site radiation releases, and economics

Energy from thorium?! Reconnoitering a new possibility : FEA

NARCIS (Netherlands)

van Klinken, J.

1998-01-01

The worldwide increasing energy consumption depends largely on fossil resources and is not sustainable. Section 1 starts with a reflection on this precarious situation as an introduction to a recently proposed possibility of a thorium-fueled sub-critical reactor driven by a proton accelerator. In

Design study of a PWR of 1300 MWe of Angra-2 type operating in the thorium cycle

International Nuclear Information System (INIS)

Andrade, E.P.; Carneiro, F.A.N.; Schlosser, J.G.

1984-01-01

The utilization of the thorium-highly enriched uranium and of the thorium-plutonium mixed oxide fuels in an unmodified PWR is analysed. Reactor core design calculations were performed for both types of fuels considering once-through and recycle fuels. The calculations were performed with the KWU design codes FASER-3 and MEDIUM-2.2 after introduction of the thorium chain and some addition of nuclide data in FASER-3. A two-energy group scheme and a two-dimensional (XY) representation of the reactor core were utilized. No technical problem that precluded the utilization of any of the options analyzed was found. The savings in uranium ore introduced by the thorium cycle with fuel recycling ranges from 13% to 52% as compared with the usual uranium once-through cycle; the SWU savings goes from 13% to 22%. (Author) [pt

Compatibility studies of potential molten-salt breeder reactor materials in molten fluoride salts

International Nuclear Information System (INIS)

Keiser, J.R.

1977-05-01

The molten fluoride salt compatibility studies carried out during the period 1974--76 in support of the Molten-Salt Reactor Program are summarized. Thermal-convection and forced-circulation loops were used to measure the corrosion rate of selected alloys. Results confirmed the relationship of time, initial chromium concentration, and mass loss developed by previous workers. The corrosion rates of Hastelloy N and Hastelloy N modified by the addition of 1--3 wt percent Nb were well within the acceptable range for use in an MSBR. 13 figures, 3 tables

Virginia ADS consortium - thorium utilization

International Nuclear Information System (INIS)

Myneni, Ganapati

2015-01-01

A Virginia ADS consortium, consisting of Virginia Universities (UVa, VCU, VT), Industry (Casting Analysis Corporation, GEM*STAR, MuPlus Inc.), Jefferson Lab and not-for-profit ISOHIM, has been organizing International Accelerator-Driven Sub-Critical Systems (ADS) and Thorium Utilization (ThU) workshops. The third workshop of this series was hosted by VCU in Richmond, Virginia, USA Oct 2014 with CBMM and IAEA sponsorship and was endorsed by International Thorium Energy Committee (IThEC), Geneva and Virginia Nuclear Energy Consortium Authority. In this presentation a brief summary of the successful 3 rd International ADS and ThU workshop proceedings and review the worldwide ADS plans and/or programs is given. Additionally, a report on new start-ups on Molten Salt Reactor (MSR) systems is presented. Further, a discussion on potential simplistic fertile 232 Th to fissile 233 U conversion is made

Thorium-based fuel cycles: Reassessment of fuel economics and proliferation risk

Energy Technology Data Exchange (ETDEWEB)

Serfontein, Dawid E., E-mail: Dawid.Serfontein@nwu.ac.za [Senior Lecturer at the School of Mechanical and Nuclear Engineering, North West University (PUK-Campus), PRIVATE BAG X6001, Internal Post Box 360, Potchefstroom 2520 (South Africa); Mulder, Eben J. [Professor at the School of Mechanical and Nuclear Engineering, North West University (South Africa)

2014-05-01

At current consumption and current prices, the proven reserves for natural uranium will last only about 100 years. However, the more abundant thorium, burned in breeder reactors, such as large High Temperature Gas-Cooled Reactors, and followed by chemical reprocessing of the spent fuel, could stretch the 100 years for uranium supply to 15,000 years. Thorium-based fuel cycles are also viewed as more proliferation resistant compared to uranium. However, several barriers to entry caused all countries, except India and Russia, to abandon their short term plans for thorium reactor projects, in favour of uranium/plutonium fuel cycles. In this article, based on the theory of resonance integrals and original analysis of fast fission cross sections, the breeding potential of {sup 232}Th is compared to that of {sup 238}U. From a review of the literature, the fuel economy of thorium-based fuel cycles is compared to that of natural uranium-based cycles. This is combined with a technical assessment of the proliferation resistance of thorium-based fuel cycles, based on a review of the literature. Natural uranium is currently so cheap that it contributes only about 10% of the cost of nuclear electricity. Chemical reprocessing is also very expensive. Therefore conservation of natural uranium by means of the introduction of thorium into the fuel is not yet cost effective and will only break even once the price of natural uranium were to increase from the current level of about $70/pound yellow cake to above about $200/pound. However, since fuel costs constitutes only a small fraction of the total cost of nuclear electricity, employing reprocessing in a thorium cycle, for the sake of its strategic benefits, may still be a financially viable option. The most important source of the proliferation resistance of {sup 232}Th/{sup 233}U fuel cycles is denaturisation of the {sup 233}U in the spent fuel by {sup 232}U, for which the highly radioactive decay chain potentially poses a large

Methodology of simultaneous analysis of Uranium and Thorium by nuclear and atomic techniques. Application to the Uranium and Thorium dosing in mineralogic samples

International Nuclear Information System (INIS)

Fakhi, S.

1988-01-01

This work concerns essentially the potential applications of 100 kW nuclear reactor of Strasbourg Nuclear Research Centre to neutron activation analysis of Uranium and Thorium. The Uranium dosing has been made using: 239-U, 239-Np, fission products or delayed neutrons. Thorium has been showed up by means of 233-Th or 233-Pa. The 239-U and 233-Th detection leads to a rapid and non-destructive analysis of Uranium and Thorium. The maximum sensitivity is of 78 ng for Uranium and of 160 ng for Thorium. The Uranium and Thorium dosing based on 239-Np and 233-Pa detection needs chemical selective separations for each of these radionuclides. The liquid-liquid extraction has permitted to elaborate rapid and quantitative separation methods. The sensitivities of the analysis after extraction reach 30 ng for Uranium and 50 ng for Thorium. The fission products separation study has allowed to elaborate the La, Ce and Nd extractions and its application to the Uranium dosing gives satisfying results. A rapid dosing method with a sensitivity of 0.35 microgramme has been elaborated with the help of delayed neutrons measurement. These different methods have been applied to the Uranium and Thorium dosing in samples coming from Oklo mine in Gabon. The analyses of these samples by atomic absorption spectroscopy and by the proton induced X-ray emission (PIXE) method confirm that the neutron activation analysis methods are reliable. 37 figs., 14 tabs., 50 refs

The safety of operations in the Dragon fuel element production building during the manufacture of thorium fuel for the first charge of the Dragon Reactor experiment

International Nuclear Information System (INIS)

Beutler, H.; Gardham, B.; Holliday, J.

1965-04-01

The first charge of fuel and fuel elements for the Dragon Reactor has been completed without significant difficulty. This report covers the safety of operations during the production of the 10 thorium elements together with the final 2 driver elements needed to complete the 37 element charge. (author)

Research of natural resources saving by design studies of Pressurized Light Water Reactors and High Conversion PWR cores with mixed oxide fuels composed of thorium/uranium/plutonium

International Nuclear Information System (INIS)

Vallet, V.

2012-01-01

Within the framework of innovative neutronic conception of Pressurized Light Water Reactors (PWR) of 3. generation, saving of natural resources is of paramount importance for sustainable nuclear energy production. This study consists in the one hand to design high Conversion Reactors exploiting mixed oxide fuels composed of thorium/uranium/plutonium, and in the other hand, to elaborate multi-recycling strategies of both plutonium and 233 U, in order to maximize natural resources economy. This study has two main objectives: first the design of High Conversion PWR (HCPWR) with mixed oxide fuels composed of thorium/uranium/plutonium, and secondly the setting up of multi-recycling strategies of both plutonium and 233 U, to better natural resources economy. The approach took place in four stages. Two ways of introducing thorium into PWR have been identified: the first is with low moderator to fuel volume ratios (MR) and ThPuO 2 fuel, and the second is with standard or high MR and ThUO 2 fuel. The first way led to the design of under-moderated HCPWR following the criteria of high 233 U production and low plutonium consumption. This second step came up with two specific concepts, from which multi-recycling strategies have been elaborated. The exclusive production and recycling of 233 U inside HCPWR limits the annual economy of natural uranium to approximately 30%. It was brought to light that the strong need in plutonium in the HCPWR dedicated to 233 U production is the limiting factor. That is why it was eventually proposed to study how the production of 233 U within PWR (with standard MR), from 2020. It was shown that the anticipated production of 233 U in dedicated PWR relaxes the constraint on plutonium inventories and favours the transition toward a symbiotic reactor fleet composed of both PWR and HCPWR loaded with thorium fuel. This strategy is more adapted and leads to an annual economy of natural uranium of about 65%. (author) [fr

Transmutation of minor actinides in a Candu thorium borner

International Nuclear Information System (INIS)

Sahin, S.; Sahin, H. M.; Acir, A.; Yalcin, S.; Yildiz, K.; Sahin, N.; Altinok, T.; Alkan, M.

2007-01-01

The paper investigates the prospects of exploitation of rich world thorium reserves in CANDU reactors. Large quantities of plutonium have been accumulated in the nuclear waste of civilian LWRs and CANDU reactors. Reactor grade plutonium can be used as a booster fissile fuel material in form of mixed ThO 2 /PuO 2 fuel in a CANDU fuel bundle in order to assure reactor criticality. Two different fuel compositions have been selected for investigations: 1) 96% thoria (ThO 2 ) + 4% PuO 2 and 2) 91% ThO 2 + 5% UO 2 + 4 PuO 2 . The latter is used for the purpose of denaturing the new 2 33U fuel with 2 38U. The behavior of the criticality k ∞ and the burn-up values of the reactor have been pursued by full power operation for > ∼ 8 years. The reactor starts with k ∞ = ∼ 1.39 and the criticality drops down asymptotically to values k ∞ > 1.06, still tolerable and usable in a CANDU reactor. Reactor criticality k ∞ remains nearly constant between the 4th year and 7th year of plant operation and then a slight increase is observed thereafter, along with a continuous depletion of thorium fuel. After the 2nd year, the CANDU reactor begins to operate practically as a thorium burner. Very high burn up can be achieved with the same fuel (> 160 000 MW.D/MT). The reactor criticality would be sufficient until a great fraction of the thorium fuel is burnt up, provided that the fuel rods could be fabricated to withstand such high burn up levels. Fuel fabrication costs and nuclear waste mass for final disposal per unit energy could be reduced drastically. There is a great quantity of weapon grade plutonium accumulated in nuclear stockpiles. In the second phase of investigations, weapon grade plutonium is used as a booster fissile fuel material in form of mixed ThO 2 /PuO 2 fuel in a CANDU fuel bundle in order to assure the initial criticality at startup. Two different fuel compositions have been used: 1) 97% thoria (ThO 2 ) + 3% PuO 2 and 2) 92% ThO 2 + 5% UO 2 + 3% PuO 2 . The

Mapping of uranium and thorium in radioactive rocks using nuclear track solid detectors

International Nuclear Information System (INIS)

Bouch, C.M.

1982-01-01

α-Autoradiography and studies of induced fission in a research nuclear reactor (IEA-R1, IPEN, Sao Paulo) were done, employing Solid-State Nuclear Track detectors, in order to study the distribution of α-emitters, U and Th in rocks. Polished sections of rocks were prepared and photographed. Etching conditions were studied in order to adapt the detectors to the studies of microdistribution and macrodistribution of tracks. Polycarbonate foils (Bayer, Makrofol) were chosen as fission-fragments detectors and the technique of fission induced with reactor neutrons to obtain the distribution of U and Th were studied. Uranium and thorium standards evaporated on the surface of the detectors, as well as thorite and uraninite grains, were irradiated in order to measure the integrated flux of neutrons, the effective cross sections for fission with reactor neutrons for 232 Th(0,05b) and 238 U(0,30b) and to study the contribution of 238 U fission in thorium mapping. A technique for determination of uranium and thorium in minerals was studied and applied to Mica, for which were determined the contents of 4,2 ppb U e 58 ppb Th. (Author) [pt

A superconducting isochronous cyclotron stack as a driver for a thorium-cycle power reactor

International Nuclear Information System (INIS)

Kim, G.; May, D.; McIntyre, P.; Sattarov, A.

2001-01-01

Designs for thorium-cycle power reactors require a proton driver capable of 1 GeV energy and 10 MW total power. For this purpose we have prepared a preliminary design for the magnetic structure for a stack of 5 super-conducting isochronous cyclotrons, each delivering 2 MW beam power. By achieving the required power with multiple independent apertures rather than pushing beyond currently achieved limits, we hope to arrive at a design that is cost-minimum and reliable. Each sector magnet consists of a flux-coupled stack of cold-iron inserts supported within a single warm-iron, in a fashion inspired by the new Riken heavy-ion cyclotron. We have developed a preliminary field design in which in-plane fields are cancelled in all 5 apertures and the field-map is appropriate for the focusing optics of the sector cyclotron

Thorium research activities in Japan

International Nuclear Information System (INIS)

Sasa, Toshinobu

2015-01-01

The nuclear energy policy in Japan is based on the Uranium-Plutonium fuel cycle with Light Water Reactors (LWR) and Fast Breeder Reactors (FBR). After the accident at Fukushima-Daiichi Nuclear Power Plant, the Japanese government recognizes the importance to ensure the flexibility for future nuclear power generation and then, it was specified in the latest Japanese strategic energy plan. Two research groups related to thorium fuelled nuclear systems and fuel cycle was set up in the Atomic Energy Society of Japan in 2013. One is a 'Research Committee on Nuclear Applications of Molten Salt'. The committee was established to discuss the current molten-salt technology including molten-salt cooled reactor, molten-salt fuelled reactor, accelerator driven system, fusion reactor blankets and dry reprocessing processes. Throughout two years discussion, the committee summarizes a current state of the art and issues of molten-salt application systems. Committee also discussed the handling technologies for molten-salt reactors especially in China and United Kingdom, issues of molten-salt application to fusion reactor, dry reprocessing of spent nuclear fuel, and non-nuclear application of molten-salt. Term of the committee will be extended for further research activities

Global Uranium And Thorium Resources: Are They Adequate To Satisfy Demand Over The Next Half Century?

Science.gov (United States)

Lambert, I. B.

2012-04-01

This presentation will consider the adequacy of global uranium and thorium resources to meet realistic nuclear power demand scenarios over the next half century. It is presented on behalf of, and based on evaluations by, the Uranium Group - a joint initiative of the OECD Nuclear Energy Agency and the International Atomic Energy Agency, of which the author is a Vice Chair. The Uranium Group produces a biennial report on Uranium Resources, Production and Demand based on information from some 40 countries involved in the nuclear fuel cycle, which also briefly reviews thorium resources. Uranium: In 2008, world production of uranium amounted to almost 44,000 tonnes (tU). This supplied approximately three-quarters of world reactor requirements (approx. 59,000 tU), the remainder being met by previously mined uranium (so-called secondary sources). Information on availability of secondary sources - which include uranium from excess inventories, dismantling nuclear warheads, tails and spent fuel reprocessing - is incomplete, but such sources are expected to decrease in market importance after 2013. In 2008, the total world Reasonably Assured plus Inferred Resources of uranium (recoverable at less than 130/kgU) amounted to 5.4 million tonnes. In addition, it is clear that there are vast amounts of uranium recoverable at higher costs in known deposits, plus many as yet undiscovered deposits. The Uranium Group has concluded that the uranium resource base is more than adequate to meet projected high-case requirements for nuclear power for at least half a century. This conclusion does not assume increasing replacement of uranium by fuels from reprocessing current reactor wastes, or by thorium, nor greater reactor efficiencies, which are likely to ameliorate future uranium demand. However, progressively increasing quantities of uranium will need to be mined, against a backdrop of the relatively small number of producing facilities around the world, geopolitical uncertainties and

Outline of research program on thorium fuel supported by grant-in-aid for energy research of ministry of education, science and culture

International Nuclear Information System (INIS)

Shibata, Toshikazu

1984-01-01

Since 1980, the Research Program on Thorium Fuel has been performed under the support of Grant-in-Aid for Energy Research of the Ministry of Education, Science and Culture of Japanese Government on the university basis including several tens professors. The main results have been published in the English-written report, ''Research on Thorium Fuel (SPEY-9, 1984)''. This report describes the outline and review of the symposium held on January 31, 1984. It consists of nuclear data, reactor physics, thorium fuel, irradiation of thorium, down-stream, biological effect, molten salt reactor engineering and others. It has been the first trial to perform such a big systematic cooperative studies in nuclear field on the university basis in Japan. (author)

Promises and Challenges of Thorium Implementation for Transuranic Transmutation - 13550

Energy Technology Data Exchange (ETDEWEB)

Franceschini, F.; Lahoda, E.; Wenner, M. [Westinghouse Electric Company LLC, Cranberry Township, PA (United States); Lindley, B. [University of Cambridge (United Kingdom); Fiorina, C. [Polytechnic of Milan (Italy); Phillips, C. [Energy Solutions, Richland, WA (United States)

2013-07-01

This paper focuses on the challenges of implementing a thorium fuel cycle for recycle and transmutation of long-lived actinide components from used nuclear fuel. A multi-stage reactor system is proposed; the first stage consists of current UO{sub 2} once-through LWRs supplying transuranic isotopes that are continuously recycled and burned in second stage reactors in either a uranium (U) or thorium (Th) carrier. The second stage reactors considered for the analysis are Reduced Moderation Pressurized Water Reactors (RMPWRs), reconfigured from current PWR core designs, and Fast Reactors (FRs) with a burner core design. While both RMPWRs and FRs can in principle be employed, each reactor and associated technology has pros and cons. FRs have unmatched flexibility and transmutation efficiency. RMPWRs have higher fuel manufacturing and reprocessing requirements, but may represent a cheaper solution and the opportunity for a shorter time to licensing and deployment. All options require substantial developments in manufacturing, due to the high radiation field, and reprocessing, due to the very high actinide recovery ratio to elicit the claimed radiotoxicity reduction. Th reduces the number of transmutation reactors, and is required to enable a viable RMPWR design, but presents additional challenges on manufacturing and reprocessing. The tradeoff between the various options does not make the choice obvious. Moreover, without an overarching supporting policy in place, the costly and challenging technologies required inherently discourage industrialization of any transmutation scheme, regardless of the adoption of U or Th. (authors)

Assessment of the Use of Nitrogen Trifluoride for Purifying Coolant and Heat Transfer Salts in the Fluoride Salt-Cooled High-Temperature Reactor

Energy Technology Data Exchange (ETDEWEB)

Scheele, Randall D.; Casella, Andrew M.

2010-09-28

This report provides an assessment of the use of nitrogen trifluoride for removing oxide and water-caused contaminants in the fluoride salts that will be used as coolants in a molten salt cooled reactor.

Comparative study using different resins to determine thorium isotopes

Energy Technology Data Exchange (ETDEWEB)

Rosa, Mychelle M.L.; Silva, Paulo S.C.; Maihara, Vera A., E-mail: my_linhares@yahoo.com.br, E-mail: pscsilva@ipen.br, E-mail: vmaihara@ipen.br [Instituto de Pesquisas Energéticas e Nucleares (IPEN/CNEN-SP), São Paulo, SP (Brazil); Taddei, Maria Helena T., E-mail: mhtaddei@cnen.gov.br [Comissão Nacional de Energia Nuclear (LAPOC/CNEN), Poços de Caldas, MG (Brazil). Laboratório de Pocos de Caldas; Cheberle, Luan T.V., E-mail: luancheberle@gmail.com [Ambientis Radioproteção, Barueri, SP (Brazil)

2017-07-01

Thorium is a naturally occurring radioactive element that is widely distributed in the crust of the Earth. This element is very common in mineral formations in regions with high levels of natural radioactivity, therefore, its determination in environmental samples is important. Thorium isotopes ({sup 228}Th, {sup 230}Th, and {sup 232}Th) were determined in a reference material, the IAEA Soil 327 sample, to validate the two methods employed using different resins. The initial preparation with acid dissolution is the same to both, in the first is used anion exchange resin (DOWEX 1 x 2) and electrodeposition in silver planchets. And in the second method is used a specific chromatographic resin (TEVA) and cerium fluoride microprecipitation. At the end both analysis are quantified by alpha spectrometry. The two methods the results obtained were satisfactory for the reference material used, with relative error of less than 4% for {sup 228}Th, {sup 230}Th, and {sup 232}Th. The main differences found between them were spectrums resolutions, time and cost of analysis. (author)

Immobilization of Alkali Metal Fluorides via Recrystallization in a Cationic Lamellar Material, [Th(MoO4)(H2O)4Cl]Cl·H2O.

Science.gov (United States)

Lin, Jian; Bao, Hongliang; Qie, Meiying; Silver, Mark A; Yue, Zenghui; Li, Xiaoyun; Zhu, Lin; Wang, Xiaomei; Zhang, Linjuan; Wang, Jian-Qiang

2018-06-05

Searching for cationic extended materials with a capacity for anion exchange resulted in a unique thorium molybdate chloride (TMC) with the formula of [Th(MoO 4 )(H 2 O) 4 Cl]Cl·H 2 O. The structure of TMC is composed of zigzagging cationic layers [Th(MoO 4 )(H 2 O) 4 Cl] + with Cl - as interlamellar charge-balancing anions. Instead of performing ion exchange, alkali thorium fluorides were formed after soaking TMC in AF (A = Na, K, and Cs) solutions. The mechanism of AF immobilization is elucidated by the combination of SEM-EDS, PXRD, FTIR, and EXAFS spectroscopy. It was observed that four water molecules coordinating with the Th 4+ center in TMC are vulnerable to competition with F - , due to the formation of more favorable Th-F bonds compared to Th-OH 2 . This leads to a single crystal-to-polycrystalline transformation via a pathway of recrystallization to form alkali thorium fluorides.

Possible physics modifications to CIRUS reactor core for improved reactor utilization

International Nuclear Information System (INIS)

John, Benjamin; Khosla, S.K.; Narain, Rajendra.

1976-01-01

Two fuelling schemes for uprating the neutron flux in CIRUS reactor at Trombay, are studied. One scheme employs enriched uranium-aluminium alloy boosters, the second envisages employing thorium oxide enriched with 0.2% plutonium oxide. It is seen that the second scheme has the potential of in-situ thorium utilization. (M.G.B.)

Analysis of a sustainable gas cooled fast breeder reactor concept

International Nuclear Information System (INIS)

Kumar, Akansha; Chirayath, Sunil S.; Tsvetkov, Pavel V.

2014-01-01

Highlights: • A Thorium-GFBR breeder for actinide recycling ability, and thorium fuel feasibility. • A mixture of 232 Th and 233 U is used as fuel and LWR used fuel is used. • Detailed neutronics, fuel cycle, and thermal-hydraulics analysis has been presented. • Run this TGFBR for 20 years with breeding of 239 Pu and 233 U. • Neutronics analysis using MCNP and Brayton cycle for energy conversion are used. - Abstract: Analysis of a thorium fuelled gas cooled fast breeder reactor (TGFBR) concept has been done to demonstrate the self-sustainability, breeding capability, actinide recycling ability, and thorium fuel feasibility. Simultaneous use of 232 Th and used fuel from light water reactor in the core has been considered. Results obtained confirm the core neutron spectrum dominates in an intermediate energy range (peak at 100 keV) similar to that seen in a fast breeder reactor. The conceptual design achieves a breeding ratio of 1.034 and an average fuel burnup of 74.5 (GWd)/(MTHM) . TGFBR concept is to address the eventual shortage of 235 U and nuclear waste management issues. A mixture of thorium and uranium ( 232 Th + 233 U) is used as fuel and light water reactor used fuel is utilized as blanket, for the breeding of 239 Pu. Initial feed of 233 U has to be obtained from thorium based reactors; even though there are no thorium breeders to breed 233 U a theoretical evaluation has been used to derive the data for the source of 233 U. Reactor calculations have been performed with Monte Carlo radiation transport code, MCNP/MCNPX. It is determined that this reactor has to be fuelled once every 5 years assuming the design thermal power output as 445 MW. Detailed analysis of control rod worth has been performed and different reactivity coefficients have been evaluated as part of the safety analysis. The TGFBR concept demonstrates the sustainability of thorium, viability of 233 U as an alternate to 235 U and an alternate use for light water reactor used fuel as a

Molten fluoride fuel salt chemistry

International Nuclear Information System (INIS)

Toth, L.M.; Del Cul, G.D.; Dai, S.; Metcalf, D.H.

1995-01-01

The chemistry of molten fluorides is traced from their development as fuels in the Molten Salt Reactor Experiment with important factors in their selection being discussed. Key chemical characteristics such as solubility, redox behavior, and chemical activity are explained as they relate to the behavior of molten fluoride fuel systems. Development requirements for fitting the current state of the chemistry to modern nuclear fuel system are described. It is concluded that while much is known about molten fluoride behavior which can be used effectively to reduce the amount of development required for future systems, some significant molten salt chemical questions must still be addressed. copyright American Institute of Physics 1995

Mirror hybrid reactor optimization studies

International Nuclear Information System (INIS)

Bender, D.J.

1976-01-01

A system model of the mirror hybrid reactor has been developed. The major components of the model include (1) the reactor description, (2) a capital cost analysis, (3) various fuel management schemes, and (4) an economic analysis that includes the hybrid plus its associated fission burner reactors. The results presented describe the optimization of the mirror hybrid reactor, the objective being to minimize the cost of electricity from the hybrid fission-burner reactor complex. We have examined hybrid reactors with two types of blankets, one containing natural uranium, the other thorium. The major difference between the two optimized reactors is that the uranium hybrid is a significant net electrical power producer, whereas the thorium hybrid just about breaks even on electrical power. Our projected costs for fissile fuel production are approximately 50 $/g for 239 Pu and approximately 125 $/g for 233 U

Recovering of thorium contained in wastes from Thorium Purification Plant

International Nuclear Information System (INIS)

Brandao Filho, D.; Hespanhol, E.C.B.; Baba, S.; Miranda, L.E.T.; Araujo, J.A. de.

1992-08-01

A study has been developed in order to establish a chemical process for recovering thorium from wastes produced at the Thorium Purification Plant of the Instituto de Pesquisas Energeticas e Nucleares. The recovery of thorium in this process will be made by means of solvent extraction technique. Solutions of TBP/Varsol were employed as extracting agent during the runs. The influence of thorium concentration in the solution, aqueous phase acidity, volume ratio of the phases, percentage of TBP/Varsol and the contact time of the phases on the extraction of thorium and lanthanides was determined. (author)

Thermodynamic characterization of the molten salt reactor fuel - 5233

International Nuclear Information System (INIS)

Capelli, E.; Konings, R.J.M.; Benes, O.

2015-01-01

The Molten Salt Reactor (MSR) has been selected as one of the Generation IV nuclear systems. The very unique feature of this reactor concept is the liquid nature of the fuel which offers numerous advantages concerning the reactor safety. Nowadays, the research in Europe is focused on an innovative concept, the MSFR (Molten Salt Fast Reactor), that combines the generic assets of molten salt as liquid fuel with those related to fast neutron reactors and the thorium fuel cycle. For the design and safety assessment of the MSFR concept, it is extremely important to have a thorough knowledge of the physico-chemical properties of fluorides salts, which is the class of materials that is the best suited for nuclear applications. Potential chemical systems have been critically reviewed and an extensive thermodynamic database describing the most relevant systems has been created at the Institute for Transuranium Elements of the Joint Research Centre (JRC). Thermochemical equilibrium calculations are a very important tool that allows the evaluation of the performance of several salt mixtures predicting their properties and thus the optimization of the fuel composition. The work combines the experimental determination of different salt properties with the modelling of the thermodynamic functions, using the Calphad method. An overview of the experimental work and the thermodynamic assessments will be given in this paper and different fuel options for the MSFR will be discussed. (authors)

The TMSR as actinide burner and thorium breeder

International Nuclear Information System (INIS)

Merle-Lucotte, E.; Heuer, D.; Le Brun, C.; Allibert, M.; Ghetta, V.

2007-01-01

Molten Salt Reactors (MSRs) are one of the six systems retained by Generation IV as a candidate for the next generation of nuclear reactors. Molten Salt Reactor is a very attractive concept especially for the Thorium fuel cycle which allows nuclear energy production with a very low production of radio-toxic minor actinides. Studies have thus been done on the Molten Salt Breeder Reactor (MSBR) of Oak-Ridge to re-evaluate this concept. They have shown that the MSBR suffers from major drawbacks concerning for example safety and reprocessing, drawbacks incompatible with any industrial development. On the other hand, the advantages of the Thorium fuel cycle were too attractive not to look further into it. With these considerations, we have reassessed the whole concept to propose an innovative reactor called Thorium Molten Salt Reactor (TMSR). Many parametric studies of the TMSR have been carried out, correlating the core arrangement and composition, the reprocessing performances, and the salt composition. In particular, by changing the moderation ratio of the core the neutron spectrum can be modified and placed anywhere between a very thermalized neutron spectrum and a relatively fast spectrum. Even if the epithermal TMSR configurations have not been completely excluded by our calculations, our studies have shown that the reactor design where there is no graphite moderator inside the core appears to be the most promising in terms of safety coefficients, reprocessing requirements, and breeding and deployment capabilities. Larger fissile matter inventories are necessary in such a reactor configuration compared to the thermalized TMSR configurations, but the resulting deployment limitation could be solved by using transuranic elements as initial fissile load. This work is based on the coupling of a neutron transport code called MCNP with the materials evolution code REM. The former calculates the neutron flux and the reaction rates in all the cells while the latter solves

Mesocarbon microbead based graphite for spherical fuel element to inhibit the infiltration of liquid fluoride salt in molten salt reactor

Energy Technology Data Exchange (ETDEWEB)

Zhong, Yajuan, E-mail: yajuan.zhong@gmail.com [Center for Thorium Molten Salt Reactor System, Shanghai Institute of Applied Physics, Chinese Academy of Sciences, Shanghai 201800 (China); CAS Key Laboratory of Carbon Materials, Institute of Coal Chemistry, Chinese Academy of Sciences, Taiyuan 030001 (China); Zhang, Junpeng [CAS Key Laboratory of Carbon Materials, Institute of Coal Chemistry, Chinese Academy of Sciences, Taiyuan 030001 (China); Lin, Jun, E-mail: linjun@sinap.ac.cn [Center for Thorium Molten Salt Reactor System, Shanghai Institute of Applied Physics, Chinese Academy of Sciences, Shanghai 201800 (China); Xu, Liujun [Center for Thorium Molten Salt Reactor System, Shanghai Institute of Applied Physics, Chinese Academy of Sciences, Shanghai 201800 (China); University of Chinese Academy of Sciences, Beijing 100049 (China); Zhang, Feng; Xu, Hongxia; Chen, Yu; Jiang, Haitao; Li, Ziwei; Zhu, Zhiyong [Center for Thorium Molten Salt Reactor System, Shanghai Institute of Applied Physics, Chinese Academy of Sciences, Shanghai 201800 (China); Guo, Quangui [CAS Key Laboratory of Carbon Materials, Institute of Coal Chemistry, Chinese Academy of Sciences, Taiyuan 030001 (China)

2017-07-15

Mesocarbon microbeads (MCMB) and quasi-isostatic pressing method were used to prepare MCMB based graphite (MG) for spherical fuel element to inhibit the infiltration of liquid fluoride salt in molten salt reactor (MSR). Characteristics of mercury infiltration and molten salt infiltration in MG were investigated and compared with A3-3 (graphite for spherical fuel element in high temperature gas cooled reactor) to identify the infiltration behaviors. The results indicated that MG had a low porosity about 14%, and an average pore diameter of 96 nm. Fluoride salt occupation of A3-3 (average pore diameter was 760 nm) was 10 wt% under 6.5 atm, whereas salt gain did not infiltrate in MG even up to 6.5 atm. It demonstrated that MG could inhibit the infiltration of liquid fluoride salt effectively. Coefficient of thermal expansion (CTE) of MG lies in 6.01 × 10{sup −6} K{sup −1} (α{sub ∥}) and 6.15 × 10{sup −6} K{sup −1} (α{sub ⊥}) at the temperature range of 25–700 °C. The anisotropy factor of MG calculated by CTE maintained below 1.02, which could meet the requirement of the spherical fuel element (below 1.30). The constant isotropic property of MG is beneficial for the integrity and safety of the graphite used in the spherical fuel element for a MSR.

Mesocarbon microbead based graphite for spherical fuel element to inhibit the infiltration of liquid fluoride salt in molten salt reactor

International Nuclear Information System (INIS)

Zhong, Yajuan; Zhang, Junpeng; Lin, Jun; Xu, Liujun; Zhang, Feng; Xu, Hongxia; Chen, Yu; Jiang, Haitao; Li, Ziwei; Zhu, Zhiyong; Guo, Quangui

2017-01-01

Mesocarbon microbeads (MCMB) and quasi-isostatic pressing method were used to prepare MCMB based graphite (MG) for spherical fuel element to inhibit the infiltration of liquid fluoride salt in molten salt reactor (MSR). Characteristics of mercury infiltration and molten salt infiltration in MG were investigated and compared with A3-3 (graphite for spherical fuel element in high temperature gas cooled reactor) to identify the infiltration behaviors. The results indicated that MG had a low porosity about 14%, and an average pore diameter of 96 nm. Fluoride salt occupation of A3-3 (average pore diameter was 760 nm) was 10 wt% under 6.5 atm, whereas salt gain did not infiltrate in MG even up to 6.5 atm. It demonstrated that MG could inhibit the infiltration of liquid fluoride salt effectively. Coefficient of thermal expansion (CTE) of MG lies in 6.01 × 10 −6 K −1 (α ∥ ) and 6.15 × 10 −6 K −1 (α ⊥ ) at the temperature range of 25–700 °C. The anisotropy factor of MG calculated by CTE maintained below 1.02, which could meet the requirement of the spherical fuel element (below 1.30). The constant isotropic property of MG is beneficial for the integrity and safety of the graphite used in the spherical fuel element for a MSR.

Neutronic behavior of thorium fuel cycles in a very high temperature hybrid system

International Nuclear Information System (INIS)

Rodriguez Garcia, Lorena; Milian Perez, Daniel; Garcia Hernandez, Carlos; Milian Lorenzo, Daniel; Velasco, Abanades

2013-01-01

Nuclear energy needs to guarantee four important issues to be successful as a sustainable energy source: nuclear safety, economic competitiveness, proliferation resistance and a minimal production of radioactive waste. Pebble bed reactors (PBR), which are very high temperature systems together with fuel cycles based in Thorium, they could offer the opportunity to meet the sustainability demands. Thorium is a potentially valuable energy source since it is about three to four times as abundant as Uranium. It is also a widely distributed natural resource readily accessible in many countries. This paper shows the main advantages of the use of a hybrid system formed by a Pebble Bed critical nuclear reactor and two Pebble Bed Accelerator Driven Systems (ADSs) using a variety of fuel cycles with Thorium (Th+U 233 , Th+Pu 239 and Th+U). The parameters related to the neutronic behavior like deep burn, nuclear fuel breeding, Minor Actinide stockpile, power density profiles and other are used to compare the fuel cycles using the well-known MCNPX computational code. (author)

Neutronic behavior of thorium fuel cycles in a very high temperature hybrid system

Energy Technology Data Exchange (ETDEWEB)

Rodriguez Garcia, Lorena; Milian Perez, Daniel; Garcia Hernandez, Carlos; Milian Lorenzo, Daniel, E-mail: dperez@instec.cu, E-mail: cgh@instec.cu, E-mail: dmilian@instec.cu [Higher Institute of Technologies and Applied Sciences, Havana (Cuba); Velasco, Abanades, E-mail: abanades@etsii.upm.es [Department of Simulation of Thermo Energy Systems, Polytechnic University of Madrid (Spain)

2013-07-01

Nuclear energy needs to guarantee four important issues to be successful as a sustainable energy source: nuclear safety, economic competitiveness, proliferation resistance and a minimal production of radioactive waste. Pebble bed reactors (PBR), which are very high temperature systems together with fuel cycles based in Thorium, they could offer the opportunity to meet the sustainability demands. Thorium is a potentially valuable energy source since it is about three to four times as abundant as Uranium. It is also a widely distributed natural resource readily accessible in many countries. This paper shows the main advantages of the use of a hybrid system formed by a Pebble Bed critical nuclear reactor and two Pebble Bed Accelerator Driven Systems (ADSs) using a variety of fuel cycles with Thorium (Th+U{sup 233}, Th+Pu{sup 239} and Th+U). The parameters related to the neutronic behavior like deep burn, nuclear fuel breeding, Minor Actinide stockpile, power density profiles and other are used to compare the fuel cycles using the well-known MCNPX computational code. (author)

Recent Research of Thorium Molten-Salt Reactor from a Sustainability Viewpoint

Directory of Open Access Journals (Sweden)

Takashi Kamei

2012-09-01

Full Text Available The most important target of the concept “sustainability” is to achieve fairness between generations. Its expanding interpolation leads to achieve fairness within a generation. Thus, it is necessary to discuss the role of nuclear power from the viewpoint of this definition. The history of nuclear power has been the control of the nuclear fission reaction. Once this is obtained, then the economy of the system is required. On the other hand, it is also necessary to consider the internalization of the external diseconomy to avoid damage to human society caused by the economic activity itself, due to its limited capacity. An extreme example is waste. Thus, reducing radioactive waste resulting from nuclear power is essential. Nuclear non-proliferation must be guaranteed. Moreover, the FUKUSHIMA accident revealed that it is still not enough that human beings control nuclear reaction. Further, the most essential issue for sustaining use of one technology is human resources in manufacturing, operation, policy-making and education. Nuclear power will be able to satisfy the requirements of sustainability only when these subjects are addressed. The author will review recent activities of a thorium molten-salt reactor (MSR as a cornerstone for a sustainable society and describe its objectives and forecasts.

Quantitative analysis of thorium-containing materials using an Industrial XRF analyzer

International Nuclear Information System (INIS)

Hasikova, J.; Titov, V.; Sokolov, A.

2014-01-01

Thorium (Th) as nuclear fuel is clean and safe and offers significant advantages over uranium. The technology for several types of thorium reactors is proven but still must be developed on a commercial scale. In the case of commercialization of thorium nuclear reactor thorium raw materials will be on demand. With this, mining and processing companies producing Th and rare earth elements will require prompt and reliable methods and instrumentation for Th quantitative on-line analysis. Potential applicability of X-ray fluorescence conveyor analyzer CON-X series is discussed for Th quantitative or semi-quantitative on-line measurement in several types of Th-bearing materials. Laboratory study of several minerals (zircon sands and limestone as unconventional Th resources; monazite concentrate as Th associated resources and uranium ore residues after extraction as a waste product) was performed and analyzer was tested for on-line quantitative measurements of Th contents along with other major and minor components. Th concentration range in zircon sand is 50-350 ppm; its detection limit at this level is estimated at 25- 50 ppm in 5 minute measurements depending on the type of material. On-site test of the CON-X analyzer for continuous analysis of thorium traces along with other elements in zircon sand showed that accuracy of Th measurements is within 20% relative. When Th content is higher than 1% as in the concentrate of monazite ore (5-8% ThO_2) accuracy of Th determination is within 1% relative. Although preliminary on-site test is recommended in order to address system feasibility at a large scale, provided results show that industrial conveyor XRF analyzer CON-X series can be effectively used for analytical control of mining and processing streams of Th-bearing materials. (author)

Pre-Conceptual Design of a Fluoride-Salt-Cooled Small Modular Advanced High Temperature Reactor (SmAHTR)

Energy Technology Data Exchange (ETDEWEB)

Greene, Sherrell R [ORNL; Gehin, Jess C [ORNL; Holcomb, David Eugene [ORNL; Carbajo, Juan J [ORNL; Ilas, Dan [ORNL; Cisneros, Anselmo T [ORNL; Varma, Venugopal Koikal [ORNL; Corwin, William R [ORNL; Wilson, Dane F [ORNL; Yoder Jr, Graydon L [ORNL; Qualls, A L [ORNL; Peretz, Fred J [ORNL; Flanagan, George F [ORNL; Clayton, Dwight A [ORNL; Bradley, Eric Craig [ORNL; Bell, Gary L [ORNL; Hunn, John D [ORNL; Pappano, Peter J [ORNL; Cetiner, Sacit M [ORNL

2011-02-01

This document presents the results of a study conducted at Oak Ridge National Laboratory during 2010 to explore the feasibility of small modular fluoride salt-cooled high temperature reactors (FHRs). A preliminary reactor system concept, SmATHR (for Small modular Advanced High Temperature Reactor) is described, along with an integrated high-temperature thermal energy storage or salt vault system. The SmAHTR is a 125 MWt, integral primary, liquid salt cooled, coated particle-graphite fueled, low-pressure system operating at 700 C. The system employs passive decay heat removal and two-out-of-three , 50% capacity, subsystem redundancy for critical functions. The reactor vessel is sufficiently small to be transportable on standard commercial tractor-trailer transport vehicles. Initial transient analyses indicated the transition from normal reactor operations to passive decay heat removal is accomplished in a manner that preserves robust safety margins at all times during the transient. Numerous trade studies and trade-space considerations are discussed, along with the resultant initial system concept. The current concept is not optimized. Work remains to more completely define the overall system with particular emphasis on refining the final fuel/core configuration, salt vault configuration, and integrated system dynamics and safety behavior.

Recovery of valuable products from the raffinate of uranium and thorium pilot-plant

International Nuclear Information System (INIS)

Martins, E.A.J.

1990-01-01

IPEN-CNEN/SP has being very active in refining yellow cake to pure ammonium diuranate which is converted to uranium trioxide, uranium dioxide, uranium tetra-and hexa-fluoride in sequential way. The technology of the thorium purification and its conversion to nuclear grade products has been a practice since several years as well. For both elements the major waste to be worked is the raffinate from purification via TBP-varsol in pulsed columns. In this paper the actual processing technology is reviewed with special emphasis on the recovery of valuable products, mainly nitric acid, ammonium nitrate, uranium, thorium and rare earth elements. Ammonium nitrate from the precipitation of uranium diuranate is of good quality, being radioactivity and uranium-free, and recommended to be applied as fertilizer. In conclusion the main effort is to maximize the recycle and reuse of the above mentioned chemicals. (author)

Study on reprocessing of uranium-thorium fuel with solvent extraction for HTGR

International Nuclear Information System (INIS)

Jiao Rongzhou; He Peijun; Liu Bingren; Zhu Yongjun

1992-08-01

A single cycle process by solvent extraction with acid feed solution is suggested. The purpose is to reprocess uranium-thorium fuel elements which are of high burn-up and rich of 232 U from HTGR (high temperature gas cooled reactor). The extraction cascade tests have been completed. The recovery of uranium and thorium is greater than 99.6%. By this method, the requirement, under remote control to re-fabricate fuel elements, of decontamination factors for Cs, Sr, Zr-Nb and Ru has been reached

An extraction method of uranium 233 from the thorium irradiates in a reactor core

International Nuclear Information System (INIS)

Chesne, A.; Regnaut, P.

1955-01-01

Description of the conditions of separation of the thorium, of the uranium 233 and of the protactinium 233 in hydrochloric solution by absorption then selective elution on anion exchange resin. A precipitation of the thorium by the oxalic acid permits the recuperation of the hydrochloric acid which is recycled, the main, raw material consumed being the oxalic acid. (authors) [fr

A comparison between thorium-uranium and low enrichment uranium cycles in the high temperature reactors

Energy Technology Data Exchange (ETDEWEB)

Cerles, J M

1973-03-15

In a previous report, it was shown that the Uranium cycle could be used as well with multi-hole block (GGA type) as with tubular elements. Now, in a F.S.V. geometry, a comparison is made between Thorium cycle and Uranium cycle. This comparison will be concerned with the physical properties of the materials, the needs of natural Uranium, the fissile material inventory and, at last, an attempt of economical considerations. In this report the cycle will be characterizd by the fertile material. So, we write ''Thorium cycle'' for Highly Enriched Uranium - Thorium cycle and ''Uranium cycle'' for low Enrichment Uranium cycle.

Studies on the preparation of thorium metal sponge from thorium oxalate

International Nuclear Information System (INIS)

Vijay, P.L.; Sehra, J.C.; Sundaram, C.V.; Gurumurthy, K.R.; Raghavan, R.V.

1978-01-01

The results of investigations carried out on the production of high purity thorium metal sponge, starting with thorium oxalate are presented. The flow sheet includes chlorination of thorium oxalate, purification of raw thorium tetrachloride, magnesium reduction of anhydrous thorium tetrachloride, slag metal separation, vacuum distillation for removal of residual MgCl 2 and excess magnesium, and consolidation of the metal sponge. Studies have been carried out to investigate the optimum chlorination efficiency and chlorine utilization attainable using different chlorinating agents, and to compare the quality of the sponge obtained with single and double distilled chloride. The overall process efficiency under optimum conditions was 81%. The thorium metal button, prepared from the sponge by arc-melting, analysed : O 2 - 847, N 2 - 20, C - 179, Mg - 100, Fe - 49, Ni<50, Al - 11, Cr - 7 (expressed in parts per million parts of thorium). The button could be further purified by electron beam melting to improve its ductility. (author)

Method for investigating the applicability of thorium-based fuels in existing BWRs

International Nuclear Information System (INIS)

Bjoerk, Klara Insulander; Fhager, Valentin; Demaziere, Christophe

2009-01-01

In this paper, a methodology for investigating the applicability of thorium based fuels in existing Boiling Water Reactors is described. The same tools and methods as those used in this study are also used for design of new fuel batches for existing reactors. As an illustration of the proposed methodology and for the purpose of comparing different fissile components for thorium-based fuel, three different thorium-based fuel designs were developed, and a low enriched uranium fuel design was created in parallel as a reference. The different fuel assemblies, which are based on the mechanical fuel design GE14, were analyzed with the Studsvik Scandpower CASMO-4E code. The linear reactivity model was used to decide a suitable initial fissile content for meeting the burnup goal of 55 MWd/kgHM and the designs were optimized for attaining an even power distribution and for keeping boiling transition factors low. Such optimizations facilitate core designs that would meet prevalent demands on Linear Heat Generation Rate (LHGR) and Critical Power Ratio (CPR). The hence created fuel designs were then analyzed with regards to thermal performance, reactivity coefficients, delayed neutron fractions and control rod worths. An equilibrium core loading pattern was also developed with each one of the thus created fuel designs and analyzed with the three dimensional reactor analysis code SIMULATE-3, also developed by Studsvik Scandpower. The results of the two simulations were compared and found to be coherent, and no major obstacles were met using the given tools and methods. The analysis of the performances of the fuel assemblies and the corresponding loaded cores is reported in a companion paper (K. Insulander Bjoerk, V. Fhager, and C. Demaziere, 'Comparison of Thorium-Based Fuels with Different Fissile Components in Existing BWRs'). (author)

Conceptual design study of small long-life PWR based on thorium cycle fuel

International Nuclear Information System (INIS)

Subkhi, M. Nurul; Su'ud, Zaki; Waris, Abdul; Permana, Sidik

2014-01-01

A neutronic performance of small long-life Pressurized Water Reactor (PWR) using thorium cycle based fuel has been investigated. Thorium cycle which has higher conversion ratio in thermal region compared to uranium cycle produce some significant of 233 U during burn up time. The cell-burn up calculations were performed by PIJ SRAC code using nuclear data library based on JENDL 3.3, while the multi-energy-group diffusion calculations were optimized in whole core cylindrical two-dimension R-Z geometry by SRAC-CITATION. this study would be introduced thorium nitride fuel system which ZIRLO is the cladding material. The optimization of 350 MWt small long life PWR result small excess reactivity and reduced power peaking during its operation

Conversion ratio in epithermal PWR, in thorium and uranium cycle

International Nuclear Information System (INIS)

Barroso, D.E.G.

1982-01-01

Results obtained for the conversion ratio in PWR reactors with close lattices, operating in thorium and uranium cycles, are presented. The study of those reactors is done in an unitary fuel cell of the lattices with several ratios V sub(M)/V sub(F), considering only the equilibrium cycles and adopting a non-spatial depletion calculation model, aiming to simulate mass flux of reactor heavy elements in the reactor. The neutronic analysis and the cross sections generation are done with Hammer computer code, with one critical apreciation about the application of this code in epithermal systems and with modifications introduced in the library of basic data. (E.G.) [pt

Thorium-applications and handling

International Nuclear Information System (INIS)

Reichelt, A.

1993-01-01

The most important aspects concerning the natural occurrence and extraction of thorium are presented the topics covered are: natural isotopes, occurence in minerals, thorium-activity-content of naturally occuring materials, the resulting radiation exposure, extraction of thorium from ores, time-dependent activity after separation. The sources of radiation exposure due to Thorium, caused by human activity, can be divided into two categories, namely, those in which thorium is deliberately added to (consumer) products in order to improve their usefullness, and those in which the thorium is present accidentally and unwanted due to the naturally occuring thorium in the material used in the manufacturing processes. Some examples of such products and substances will be presented and results about their specific thorium activity will be discussed. Experimental data from a currently running research programme, will be presented, and will include results concerning the radiation occupational exposure due to phosphate fertilizers, thorium impregnated gas mantles and the use of thoriated TIG-Electrodes in arc welding. (orig.) [de

The CANDUR Reactor - The Practical Path to RU and TH use in Nuclear Reactors

International Nuclear Information System (INIS)

Kuran, Sermet; Yang, Dezi

2012-01-01

The CANDU heavy water reactor has unrivalled flexibility for using a variety of fuels, such as Natural Uranium (NU), Low Enriched Uranium (LEU), Recycled Uranium (RU), Mixed Oxide (MOX), and Thorium (Th). Recently, this unique CANDU reactor feature attracted considerable attention due to favourable commercial, environmental and strategic needs. This paper summarizes the solid progress over the last three years and outlines CANDU Energy Incorporated's (CEI) multi-stage vision of utilizing various fuels in currently operational and new build CANDU reactors. In CEI's fuel-cycle vision, CANDU reactors will operate in conjunction with other reactor types and use advanced fuels to produce more energy and ensure the most efficient and least costly method of utilizing Light Water Reactor (LWR) used fuel. With this vision and the tandem goal of systematic adoption of Thorium based fuels, CANDU reactors will be a strong technology partner in ensuring the availability of long-term stable resources for nuclear power plants

Power Reactor Thoria Reprocessing Facility (PRTRF), Trombay

International Nuclear Information System (INIS)

Dhami, P.S; Yadav, J.S; Agarwal, K.

2017-01-01

Exploitation of the abundant thorium resources to meet sustained energy demand forms the basis of the Indian nuclear energy programme. To gain reprocessing experience in thorium fuel cycle, thoria was irradiated in research reactor CIRUS in early sixties. Later in eighties, thoria bundles were used for initial flux flattening in some of the pressurized heavy water reactors (PHWRs). The research reactor irradiated thoria contained small content (∼ 2-3ppm) of "2"3"2U in "2"3"3U product, which did not pose any significant radiological problems during processing in Uranium Thorium Separation Facility (UTSF), Trombay. Thoria irradiated in PHWRs on discharge contained (∼ 0.5-1.5% "2"3"3U with significant "2"3"2U content (100-500 ppm) requiring special radiological attention. Based on the experience from UTSF, a new facility viz. Power Reactor Thoria Reprocessing Facility (PRTRF), Trombay was built which was hot commissioned in the year 2015

Thorium fuel cycle management

International Nuclear Information System (INIS)

Zajac, R.; Darilek, P.; Breza, J.; Necas, V.

2010-01-01

In this presentation author deals with the thorium fuel cycle management. Description of the thorium fuels and thorium fuel cycle benefits and challenges as well as thorium fuel calculations performed by the computer code HELIOS are presented.

Analysis of burnup of Angra 2 PWR nuclear with addition of thorium dioxide fuel using ORIGEN-ARP

Energy Technology Data Exchange (ETDEWEB)

Goncalves, Isadora C.; Wichrowski, Caio C.; Oliveira, Claudio L. de; Vellozo, Sergio O.; Baptista, Camila O., E-mail: isadora.goncalves@ime.eb.br, E-mail: wichrowski@ime.eb.br, E-mail: d7luiz@yahoo.com.br, E-mail: vellozo@ime.eb.br, E-mail: camila.oliv.baptista@gmail.com [Instituto Militar de Engenharia (IME), Rio de Janeiro, RJ (Brazil). Secao de Engenharia Nuclear

2017-11-01

It is known that isotope {sup 232}thorium is a fertile nuclide with the ability to convert into {sup 233}uranium, a potentially fissile isotope, after absorbing a neutron. As there is a large stock of available thorium in the world, this element shows great promise in mitigate the world energy crisis, more particularly in the problem of uranium scarcity, besides being an alternative nuclear fuel for those currently used in reactors, and yet presenting advantages as an option for the non-proliferation movement, among others. In this study, the analysis of the remaining nuclides of burnup was carried out for the core configuration of a PWR (pressurized water reactor) reactor, specifically the Angra 2 reactor, using only uranium dioxide, its current configuration, and in different configurations including a mixed oxide of uranium and thorium in three concentrations, allowing a preliminary assessment of the feasibility of the modification of the fuel, the resulting production of {sup 233}uranium, the emergence of {sup 231}protactinium (an isotope that only occurs as a fission product of {sup 232}Th) resulting from burning. The study was carried out using data obtained from FSAR (Final Safety Analysis Report) of Angra 2, using the SCALE 6.1, a modeling and simulation nuclear code, especially its ORIGEN-ARP module, which analyzes the depletion of isotopes presents in a reactor. (author)

Analysis of burnup of Angra 2 PWR nuclear with addition of thorium dioxide fuel using ORIGEN-ARP

International Nuclear Information System (INIS)

Goncalves, Isadora C.; Wichrowski, Caio C.; Oliveira, Claudio L. de; Vellozo, Sergio O.; Baptista, Camila O.

2017-01-01

It is known that isotope "2"3"2thorium is a fertile nuclide with the ability to convert into "2"3"3uranium, a potentially fissile isotope, after absorbing a neutron. As there is a large stock of available thorium in the world, this element shows great promise in mitigate the world energy crisis, more particularly in the problem of uranium scarcity, besides being an alternative nuclear fuel for those currently used in reactors, and yet presenting advantages as an option for the non-proliferation movement, among others. In this study, the analysis of the remaining nuclides of burnup was carried out for the core configuration of a PWR (pressurized water reactor) reactor, specifically the Angra 2 reactor, using only uranium dioxide, its current configuration, and in different configurations including a mixed oxide of uranium and thorium in three concentrations, allowing a preliminary assessment of the feasibility of the modification of the fuel, the resulting production of "2"3"3uranium, the emergence of "2"3"1protactinium (an isotope that only occurs as a fission product of "2"3"2Th) resulting from burning. The study was carried out using data obtained from FSAR (Final Safety Analysis Report) of Angra 2, using the SCALE 6.1, a modeling and simulation nuclear code, especially its ORIGEN-ARP module, which analyzes the depletion of isotopes presents in a reactor. (author)

Technology assessment HTR. Part 6. The radiological risks associated with the thorium-fuelled High Temperature Reactor. A comparative risk evaluation

International Nuclear Information System (INIS)

Dodd, D.H.; Van Hienen, J.F.A.

1996-06-01

This report presents the results of task B.3 of the 'Technology Assessment of the High Temperature Reactor' project. The objective of task B.3 was to evaluate the radiological risks to the general public associated with the sustainable HTGR cycle. Since the technologies to be used at several stages of this fuel cycle are still in the design phase and since a detailed specification of this fuel cycle has not yet been developed, the emphasis was on obtaining a global impression of the risk associated with a generic thorium-based HTGR fuel cycle. This impression was obtained by performing a comparative risk analysis on the basis of data given in the literature. As reference for the comparison a generic uranium fuel led LWR cycle was used. The structure of the report is as follows. In Chapter 2 the general methodology for assessing the radiological risks associated with nuclear installations is described. An overview is given of the measures commonly used to quantify these risks. In Chapter 3 an overview is given of the different stages of the reference uranium fuel led LWR cycle and the thorium fuel led HTGR cycle. In Chapter 4 a stage-by-stage analysis is given of the radiological risks associated with the two fuel cycles. Finally, in Chapter 5 an evaluation is made of the radiological risks associated with the LWR and HTGR cycles and with thorium and uranium fuels. In Appendix A the production and releases of 14 C for LWR and HTGR fuel cycle facilities is considered in detail. 11 figs., 10 tabs., 10 refs

Thorium determination in water and biological materials by fission track

International Nuclear Information System (INIS)

Melo Ferreira, A.C. de.

1989-01-01

As a segment of a research programme on the study of bioaccumulation of radionuclides, in animals and vegetables from Morro do Ferro, Pocos de Caldas, MG, a fission track method for the determination of low levels of thorium in environmental samples was developed as an alternative for alpha spectroscopy. The study was carried out in early alpha spectroscopy samples, containing high levels of 228 Th activity, which makes difficult the 232 Th determination. A dry way method for thorium evaluation was developed. Pieces of membrane filters, containing La F 3 (Th), coupled to Makrofol detectors, were irradiated in the core of a research reactor, IEA-R1 (IPEN). (author)

Determination of natural thorium in urines; Dosage du thorium dans les urines

Energy Technology Data Exchange (ETDEWEB)

Jeanmaire, L; Jammet, H [Commissariat a l' Energie Atomique, Saclay (France).Centre d' Etudes Nucleaires

1959-07-01

A procedure for the quantitative analysis of thorium in urine is described. After precipitation with ammonium hydroxide, dissolution of the precipitate, extraction at pH 4-4.2 with cupferron in chloroformic solution and mineralization, a colorimetric determination of thorium with thorin is performed. It is thus possible to detect about 2 {gamma} of thorium in the sample. (author) [French] Cet article decrit une technique de dosage du thorium dans l'urine. Apres precipitation par l'ammoniaque, remise en solution, extraction a pH 4-4,2 par le cupferron en solution chloroformique et mineralisation, le thorium est dose par colorimetrie avec le thorin. Cette methode permet de deceler environ 2 {gamma} de thorium dans l'echantillon. (auteur)

Potential of axial fuel management strategies in thorium-fuelled CANDU's

International Nuclear Information System (INIS)

Milgram, M.S.

1978-06-01

Three axial fuel management strategies are compared for use in a CANDU-PHW reactor operating on a self-sufficient, equilibrium thorium cycle. Two of these strategies are familiar ones for uranium reactors, and the third seeks to take advantage of the nuclear characteristics of the Th 232 → U 233 transmutation chain to improve the economics of the fuel cycle by periodically removing the fuel from the reactor. This results in an approximately 50% increase in burnup and an approximately 15% decrease in heavy element fuel inventory at a channel power of 6 MW, relative to the other strategies. (author)

Studies on the liquid fluoride thorium reactor: Comparative neutronics analysis of MCNP6 code with SRAC95 reactor analysis code based on FUJI-U3-(0)

Energy Technology Data Exchange (ETDEWEB)

Jaradat, S.Q., E-mail: sqjxv3@mst.edu; Alajo, A.B., E-mail: alajoa@mst.edu

2017-04-01

Highlights: • The verification for FUJI-U3-(0)—a molten salt reactor—was performed. • The MCNP6 was used to study the reactor physics characteristics for FUJI-U3 type. • The results from the MCNP6 were comparable with the ones obtained from literature. - Abstract: The verification for FUJI-U3-(0)—a molten salt reactor—was performed. The reactor used LiF-BeF2-ThF4-UF4 as the mixed liquid fuel salt, and the core was graphite moderated. The MCNP6 code was used to study the reactor physics characteristics for the FUJI-U3-(0) reactor. Results for reactor physics characteristic of the FUJI-U3-(0) exist in literature, which were used as reference. The reference results were obtained using SRAC95 (a reactor analysis code) coupled with ORIGEN2 (a depletion code). Some modifications were made in the reconstruction of the FUJI-U3-(0) reactor in MCNP due to unavailability of more detailed description of the reactor core. The assumptions resulted in two representative models of the reactor. The results from the MCNP6 models were compared with the reference results obtained from literature. The results were comparable with each other, but with some notable differences. The differences are because of the approximations that were done on the SRAC95 model of the FUJI-U3 to simplify the simulation. Based on the results, it is concluded that MCNP6 code predicts well the overall simulation of neutronics analysis to the previous simulation works using SRAC95 code.

A novel concept of QUADRISO particles Part III: applications to the plutonium-thorium fuel cycle

International Nuclear Information System (INIS)

Talamo, A.

2009-01-01

In the present study, a plutonium-thorium fuel cycle is investigated including the 233 U production and utilization. A prismatic thermal High Temperature Gas Reactor (HTGR) and the novel concept of quadruple isotropic (QUADRISO) coated particles, designed at the Argonne National Laboratory, have been used for the study. In absorbing QUADRISO particles, a burnable poison layer surrounds the central fuel kernel to flatten the reactivity curve as a function of time. At the beginning of life, the fuel in the QUADRISO particles is hidden from neutrons, since they get absorbed in the burnable poison before they reach the fuel kernel. Only when the burnable poison depletes, neutrons start streaming into the fuel kernel inducing fission reactions and compensating the fuel depletion of ordinary TRISO particles. In fertile QUADRISO particles, the absorber layer is replaced by natural thorium with the purpose of flattening the excess of reactivity by the thorium resonances and producing 233 U. The above configuration has been compared with a configuration where fissile (neptunium-plutonium oxide from Light Water Reactors irradiated fuel) and fertile (natural thorium oxide) fuels are homogeneously mixed in the kernel of ordinary TRISO particles. For the 233 U utilization, the core has been equipped with europium oxide absorbing QUADRISO particles.

Impact on breeding rate of different Molten Salt reactor core structures

International Nuclear Information System (INIS)

Wang Haiwei; Mei Longwei; Cai Xiangzhou; Chen Jingen; Guo Wei; Jiang Dazhen

2013-01-01

Background: Molten Salt Reactor (MSR) has several advantages over the other Generation IV reactor. Referred to the French CNRS research and compared to the fast reactor, super epithermal neutron spectrum reactor type is slightly lower and beading rate reaches 1.002. Purpose: The aim is to explore the best conversion zone layout scheme in the super epithermal neutron spectrum reactor. This study can make nuclear fuel as one way to solve the energy problems of mankind in future. Methods: Firstly, SCALE program is used for molten salt reactor graphite channel, molten salt core structure, control rods, graphite reflector and layer cladding structure. And the SMART modules are used to record the important actinides isotopes and their related reaction values of each reaction channel. Secondly, the thorium-uranium conversion rate is calculated. Finally, the better molten salt reactor core optimum layout scheme is studied comparing with various beading rates. Results: Breading zone layout scheme has an important influence on the breading rate of MSR. Central graphite channels in the core can get higher neutron flux irradiation. And more 233 Th can convert to 233 Pa, which then undergoes beta decay to become 233 U. The graphite in the breading zone gets much lower neutron flux irradiation, so the life span of this graphite can be much longer than that of others. Because neutron flux irradiation in the uranium molten salt graphite has nearly 10 times higher than the graphite in the breading zone, it has great impact on the thorium-uranium conversion rates. For the super epithermal neutron spectrum molten salt reactors, double salt design cannot get higher thorium-uranium conversion rates. The single molten salt can get the same thorium-uranium conversion rate, meanwhile it can greatly extend the life of graphite in the core. Conclusions: From the analysis of calculation results, Blanket breeding area in different locations in the core can change the breeding rates of thorium

Development of technology and equipment for manufacturing fluorides rare-earths via non-aqueous method

International Nuclear Information System (INIS)

Chatalov, V.V.; Kozlov, O.I.; Machirev, V.P.; Zvonarev, E.N.

1998-01-01

Full text: The works on technology and equipment for rare earths (RE) fluorides are very scarce. Presently RE-fluorides are manufactured by various methods. Conventionally they can be divided into two main groups. The first group comprises methods based on precipitation of fluorides from soluble salts of corresponding metals by fluohydric acid (aqueous methods) with following thermal decomposition of aquatic fluorides obtained until anhydric state is reached. The second group (called dry, gaseous or non-aqueous) comprises methods based on direct fluorizating (by fluorine hydride, fluor or other fluorating agents) have several important advantages compared to the aqueous methods: the fluorides obtained are anhydrous; the operations of fluoride precipitation, washing, decantation, filtration are excluded as well as their drying and calcination. The process of calcination is, as a rule, accompanied by pyrohydrolysis. The products manufactured by precipitation are inferior to those obtained by the non-aqueous technique. The world production practice uses both groups of methods. Nevertheless, the method of gaseous hydrofluorination is preferable. In all non-aqueous processes the initial materials are oxides RE which interact with gaseous fluorine hydride. The initial materials - oxides are obtained by thermal decomposition of carbonates, hydroxides, oxalates and so on. One of the best type of apparatus for thermal decomposition processes is a horizontal ring shaped vibrating apparatus with direct heating. The RE - fluorides is synthesized by way of RE-oxide interacting with hydrogen fluoride at 200-550 deg C in single continuous operation: (RE) 2 O 3 + 6 HF → 2 (RE)F 3 + 3 H 2 0 The apparatus consists of a nickel horizontal two tube screw. Reaction time is varied from 2 to 6 hours; the productivity of reactor is defined by feed screw rotation and initial material bulk density. Hydrogen fluoride was passing the reactor opposite to the solid phase. The degree

A review of the potential for actinide redistribution in CANDU thorium cycle fuels

International Nuclear Information System (INIS)

Cameron, D.J.

1978-02-01

Actinide redistribution resulting from large radial temperature gradients is an accepted feature of the technology of fast reactor (U,Pu)O 2 fuels. A thorium cycle in CANDU reactors would require the use of oxide fuels with two or more components, raising the question of actinide redistribution in these fuels. The mechanisms proposed to explain redistribution in (U,Pu)O 2 fuels are reviewed, and their relevance to fuels based on ThO 2 is discussed. The fuel primarily considered is (Th,U)O 2 but some reference is made to (Th,Pu)O 2 . At this early stage of thorium fuel cycle technology, it is not possible to consider quantitatively the question of redistribution in specific fuels. However, some guidelines can be presented to indicate to fuel engineers conditions which might result in significant redistribution. It is concluded that redistribution is probably of little concern in high density, CANDU, thorium cycle fuel whose centre temperature is limited to 2350 K. If this centre temperature is exceeded, or if the fuel contains substantial inter-connected porosity, the potential for redistribution is significant and warrants more serious study. (author)

Assessment of thorium and thoron decay products in air - thorium plant

International Nuclear Information System (INIS)

Dhandayutham, R.; Gohel, C.O.; Shetty, P.N.; Savant, P.B.; Rao, D.V.V.

1977-01-01

For the evaluation of radiation dose to the lungs in a thorium plant, it is necessary to estimate the concentration of thorium, thoron and its daughter products in air. Methods employed in estimating thorium and its decay products and 'working level' are presented. (M.G.B.)

Determination of sulfate in thorium salts using gravimetric technique with previous thorium separation

International Nuclear Information System (INIS)

Silva, C.M. da; Pires, M.A.F.

1994-01-01

Available as short communication only. A simple analytical method to analyze sulfates in thorium salt, is presented. The method is based on the thorium separation as hydroxide. The gravimetric technique is used to analyze the sulfate in the filtered as barium sulfate. Using this method, the sulfate separation from thorium has been reach 99,9% yield, and 0,1% precision. This method is applied to thorium salts specifically thorium sulfate, carbonate and nitrate. (author). 5 refs, 2 tabs

Operation of CANDU power reactor in thorium self-sufficient fuel cycle

Indian Academy of Sciences (India)

These disadvantages of thorium fuel cycle were seemingly the reasons why that ... According to the data of figure 2, maximum (equilibrium) content of 233U in ..... Self-sufficient mode is related with rather big effort in the extraction of isotopes of.

The influence of thorium on the temperature reactivity coefficient in a 400 MWth pebble bed high temperature plutonium incinerating reactor

International Nuclear Information System (INIS)

Richards, Guy A.; Serfontein, Dawid E.

2014-01-01

This article investigates advanced fuel cycles containing thorium and reactor grade plutonium (Pu(PWR)) in a 400 MW th Pebble Bed Modular Reactor (PBMR) Demonstration Power Plant. Results presented were determined from coupled neutronics and thermo-hydraulic simulations of the VSOP 99/05 diffusion codes. In a previous study impressive burn-ups (601 MWd/kg heavy metal (HM)) and thus plutonium destruction rates (69.2 %) were obtained with pure plutonium fuel with mass loadings of 3 g Pu(PWR)/fuel sphere or less. However the safety performance was poor in that the limit on the maximum fuel temperature during equilibrium operation was exceeded and positive Uniform Temperature Reactivity Coefficients (UTCs) were obtained. In the present study fuel cycles containing mixtures of thorium and plutonium achieved negative maximum UTCs. Plutonium only fuel cycles also achieved negative maximum UTCs, provided that much higher mass loadings are used. It is proposed that the lower thermal neutron flux was responsible for this effect. The plutonium only fuel cycle with 12 g Pu(PWR)/fuel sphere also achieved the adopted safety limits for the PBMR DPP-400 in that the maximum fuel temperature and the maximum power density did not exceed 1130°C or 4.5 kW/sphere respectively. This design would thus be licensable and could potentially be economically feasible. However the burn-up was much lower at 181 MWd/kgHM and thus the plutonium destruction fraction was also much lower at 24.5%, which may be sub-optimal with respect to proliferation and waste disposal objectives and therefore further optimisation studies are proposed. (author)

Transformation of thorium sulfate in thorium nitrate by ion exchange resin

International Nuclear Information System (INIS)

Pereira, W.

1991-01-01

A procedure for transforming thorium sulfate into thorium nitrate by means of a strong cationic ion exchanger is presented. The thorium sulfate solution (approximately 15 g/L Th (SO 4 ) 2 ) is percolate through the resin and the column is washed first with water, with a 0,2 M N H 4 OH solution and then with a 0.2 M N H 4 NO 3 solution in order to eliminate sulfate ion. Thorium is eluted with a 2 M solution of (N H 4 ) 2 CO 3 . This eluate is treated with a solution of nitric acid in order to obtain the complete transformation into Th (NO 3 ) 4 . The proposed procedure leads to good quality thorium nitrate with high uranium decontamination. (author)

Point defects in thorium nitride: A first-principles study

Energy Technology Data Exchange (ETDEWEB)

Pérez Daroca, D., E-mail: pdaroca@tandar.cnea.gov.ar [Gerencia de Investigación y Aplicaciones, Comisión Nacional de Energía Atómica (Argentina); Consejo Nacional de Investigaciones Científicas y Técnicas (Argentina); Llois, A.M. [Gerencia de Investigación y Aplicaciones, Comisión Nacional de Energía Atómica (Argentina); Consejo Nacional de Investigaciones Científicas y Técnicas (Argentina); Mosca, H.O. [Gerencia de Investigación y Aplicaciones, Comisión Nacional de Energía Atómica (Argentina); Instituto de Tecnología Jorge A. Sabato, UNSAM-CNEA (Argentina)

2016-11-15

Thorium and its compounds (carbides and nitrides) are being investigated as possible materials to be used as nuclear fuels for Generation-IV reactors. As a first step in the research of these materials under irradiation, we study the formation energies and stability of point defects in thorium nitride by means of first-principles calculations within the framework of density functional theory. We focus on vacancies, interstitials, Frenkel pairs and Schottky defects. We found that N and Th vacancies have almost the same formation energy and that the most energetically favorable defects of all studied in this work are N interstitials. These kind of results for ThN, to the best authors' knowledge, have not been obtained previously, neither experimentally, nor theoretically.

Point defects in thorium nitride: A first-principles study

International Nuclear Information System (INIS)

Pérez Daroca, D.; Llois, A.M.; Mosca, H.O.

2016-01-01

Thorium and its compounds (carbides and nitrides) are being investigated as possible materials to be used as nuclear fuels for Generation-IV reactors. As a first step in the research of these materials under irradiation, we study the formation energies and stability of point defects in thorium nitride by means of first-principles calculations within the framework of density functional theory. We focus on vacancies, interstitials, Frenkel pairs and Schottky defects. We found that N and Th vacancies have almost the same formation energy and that the most energetically favorable defects of all studied in this work are N interstitials. These kind of results for ThN, to the best authors' knowledge, have not been obtained previously, neither experimentally, nor theoretically.

High-Temperature Gas-Cooled Reactor Critical Experiment and its Application to Thorium Absorption Rates

International Nuclear Information System (INIS)

Bardes, R.G.; Brown, J.R.; Drake, M.K.; Fischer, P.U.; Pound, D.C.; Sampson, J.B.; Stewart, H.B.

1964-01-01

In developing the concept of the HTGR and its first prototype at Peach Bottom, General Atomic made the decision that a critical experiment was required to provide adequately certain necessary input data for the nuclear analysis. The specific needs of the nuclear design theory for input data relating to thorium absorptions led to an experimental design consisting of a central lattice-type critical assembly with surrounding buffer and driver regions. This type of assembly, in which the spectrum of interest can be established in the relatively small central lattice having a desired geometry, provides a useful tool for obtaining a variety of input data for nuclear analysis surveys of new concepts. The particular advantages of this approach over that of constructing a mock-up assembly will be discussed, as well as the role of the theory in determining what experiments are most useful and how these experiments are then used in verifying design techniques. Two relatively new techniques were developed for use in the lattice assembly. These were a reactivity oscillation technique for determining the thorium Doppler coefficient, and an activation technique for determining both the resonance integral of thorium dispersed in graphite and its temperature dependence (activation Doppler coefficient). The Doppler coefficient measurement by reactivity oscillation utilized the entire central fuel element in a technique which permitted heating this fuel element to 800°F and accurately subtracting experimentally the thermal-base effects, that is, those effects not contributing to the thorium resonance capture. Comparison of results with theory for a range of conditions shows excellent agreement. The measurement of the thorium resonance integral and its temperature dependence will be described. The technique developed for measuring resonance capture makes use of gold as the standard and vanadium as die material giving the 1/v absorption rate. This technique is dictated by the fact

Symbiosis of near breeder HTR's with hybrid fusion reactors

International Nuclear Information System (INIS)

Seifritz, W.

1978-07-01

In this contribution to INFCE a symbiotic fusion/fission reactor system, consisting of a hybrid beam-driven micro-explosion fusion reactor (HMER) and associated high-temperature gas-cooled reactors (HTR) with a coupled fuel cycle, is proposed. This system is similar to the well known Fast Breeder/Near Breeder HTR symbiosis except that the fast fission breeder - running on the U/Pu-cycle in the core and the axial blankets and breeding the surplus fissile material as U-233 in its radial thorium metal or thorium oxide blankets - is replaced by a hybrid micro-explosion DT fusion reactor

Advanced epithermal thorium reactor (AETR) physics; Physique d'un reacteur au thorium, a neutrons epithermiques, de type perfectionne (AETR); Fizika usovershenstvovannog o nadteplovogo torievogo reaktora; Fisica del reactor epitermico de tipo avanzado, alimentado con torio (AETR)

Energy Technology Data Exchange (ETDEWEB)

Campise, A. V. [Atomics International, Canoga Park, CA (United States)

1962-03-15

'etude de cet ensemble a mis en relief l'importance des donnees relatives aux sections efficaces et de l'interpretation theorique des resultats experimentaux pour l'etude d'un reacteur au thorium de type perfectionne. La precision des methodes analytiques employees a ete demontree lors de l'analyse des resultats experimentaux obtenus avec le ZPR-III. L'auteur compare trois configurations pour le transfert de chaleur, en utilisant le temps de doublement comme parametre d'optimisation. Les effets de la production de {sup 233}Pa et d'isotopes de l'uranium sur le bilan neutronique, les taux possibles de surgeneration et les caracteristiques de la combustion sont evalues en tenant compte de l'imprecision des sections efficaces nucleaires. (author) [Spanish] El autor estudia la concepcion del reactor AETR desde el punto de vista de la teoria actual de los parametros nucleares y del balance neutronico. En los sistemas moderados por grafito examina el efecto de la captura por resonancia en el torio para energias medias de absorcion del orden de 0,10 a 100 keV. Aplica formulas de resonancia angosta y de resonancia ancha para obtener la integral de resonancia efectiva en funcion de la temperatura, correspondiente a las barras de torio, y dicho parametro se expresa como secciones eficaces equivalentes de varios grupos. Se ha disenado y construido un conjunto critico para obtener datos nucleares indispensables en la gama de energias intermedias. En el diseno nuclear de dicho conjunto, se ha tenido particularmente en cuenta la importancia de los datos relativos a secciones eficaces y la interpretacion teorica de estos resultados experimentales, cosas ambas relacionadas con el diseno del reactor AETR. La precision de los metodos analiticos ha quedado demostrada por el estudio de los resultados experimentales obtenidos con el reactor ZPR-III. Se comparan tres sistemas de transmision de calor utilizando el tiempo de duplicacion como parametro optimo. Se estudia el efecto de la formacion

CANDU reactors with reactor grade plutonium/thorium carbide fuel

Energy Technology Data Exchange (ETDEWEB)

Sahin, Suemer [Atilim Univ., Ankara (Turkey). Faculty of Engineering; Khan, Mohammed Javed; Ahmed, Rizwan [Pakistan Institute of Engineering and Applied Sciences, Islamabad (Pakistan); Gazi Univ., Ankara (Turkey). Faculty of Technology

2011-08-15

Reactor grade (RG) plutonium, accumulated as nuclear waste of commercial reactors can be re-utilized in CANDU reactors. TRISO type fuel can withstand very high fuel burn ups. On the other hand, carbide fuel would have higher neutronic and thermal performance than oxide fuel. In the present work, RG-PuC/ThC TRISO fuels particles are imbedded body-centered cubic (BCC) in a graphite matrix with a volume fraction of 60%. The fuel compacts conform to the dimensions of sintered CANDU fuel compacts are inserted in 37 zircolay rods to build the fuel zone of a bundle. Investigations have been conducted on a conventional CANDU reactor based on GENTILLYII design with 380 fuel bundles in the core. Three mixed fuel composition have been selected for numerical calculation; (1) 10% RG-PuC + 90% ThC; (2) 30% RG-PuC + 70% ThC; (3) 50% RG-PuC + 50% ThC. Initial reactor criticality values for the modes (1), (2) and (3) are calculated as k{sub {infinity}}{sub ,0} = 1.4848, 1.5756 and 1.627, respectively. Corresponding operation lifetimes are {proportional_to} 2.7, 8.4, and 15 years and with burn ups of {proportional_to} 72 000, 222 000 and 366 000 MW.d/tonne, respectively. Higher initial plutonium charge leads to higher burn ups and longer operation periods. In the course of reactor operation, most of the plutonium will be incinerated. At the end of life, remnants of plutonium isotopes would survive; and few amounts of uranium, americium and curium isotopes would be produced. (orig.)

Neutron irradiation effects on the mechanical properties of thorium and thorium--carbon alloy

International Nuclear Information System (INIS)

Wang, S.C.P.

1978-04-01

The effects of neutron exposure to 3.0 x 10 18 neutrons/cm 2 on the mechanical properties of thorium and thorium-carbon alloy are described. Tensile measurements were done at six different test temperatures from 4 0 K to 503 0 K and at two strain rates. Thorium and thorium-carbon alloy are shown to display typical radiation hardening like other face-centered cubic metals. The yield drop phenomenon of the thorium-carbon alloy is unchanged after irradiation. The variation of shear stress and effective shear stress with test temperature was fitted to Seeger's and Fleischer's equations for irradiated and unirradiated thorium and thorium-carbon alloy. Neutron irradiation apparently contributes an athermal component to the yield strength. However, some thermal component is detected in the low temperature range. Strain-rate parameter is increased and activation volume is decreased slightly for both kinds of metal after irradiation

Role of the ADS from the perspective of the International Thorium Energy Committee iThEC

International Nuclear Information System (INIS)

Kadi, Y.

2015-01-01

The international Thorium Energy Committee (iThEC) in Geneva has been established to investigate the ADS (accelerator-driven subcritical reactor) fuelled by thorium. The committee, formed by prominent members of the scientific community of CERN also comprises business leaders and members acquainted with public relations in an effort aimed at broadening the appeal of the ADS concept. The use of thorium in a subcritical fast reactor configuration driven by an accelerator and cooled by natural convection of liquid metal offers significant advantages in terms of resource abundance, security, non-proliferation and drastic reduction of existing and future waste. Switzerland has unique strengths in a number of areas directly related to the basic elements of an ADS system for the destruction of nuclear waste. First, the Paul Scherrer Institute (PSI) in Villigen has developed a cyclotron with a proton beam whose characteristics and power have the capacity to drive a nuclear waste incinerator. Secondly, the presence of CERN in Switzerland is also an important asset because it is at CERN that the founding experiments of an ADS were performed. iThEC proposes that Switzerland undertakes, along with other interested parties, a programme on the elimination of nuclear waste through the thorium-ADS concept

Operation and utilization of low power research reactor critical facility for Advanced Heavy Water Reactor (AHWR)

International Nuclear Information System (INIS)

De, S.K.; Karhadkar, C.G.

2017-01-01

An Advanced Heavy Water Reactor (AHWR) has been designed and developed for maximum power generation from thorium considering large reserves of thorium. The design envisages using 54 pin MOX cluster with different enrichment of "2"3"3U and Pu in Thoria fuel pins. Theoretical models developed to neutron transport and the geometrical details of the reactor including all reactivity devices involve approximations in modelling, resulting in uncertainties. With a view to minimize these uncertainties, a low power research reactor Critical Facility was built in which cold clean fuel can be arranged in a desired and precise geometry. Different experiments conducted in this facility greatly contribute to understand and validate the physics design parameters

Burn-up calculations for a thorium HTR with one and with two types of fuel particle

Energy Technology Data Exchange (ETDEWEB)

Griggs, C. F.

1975-06-15

Cell burn-up calculations have been made on a thorium pin-cell operating with one or with two types of particle. With one particle, the input thorium and uranium are mixed prior to irradiation and all discharged uranium is recycled. With two particles, the fuel is kept in two streams and only the uranium generated from thorium is recycled. The two models are found to give similar power generations from a given initial U-235 input. The choice between the two types of particle is probably not determined by reactor physics considerations but by the value of the fuel credits and by the cost of fuel fabrication and reprocessing.

Study on thorium removal from effluent by electrocoagulation

International Nuclear Information System (INIS)

Nath, Baidurjya; Swaroopa Lakshmi, Y.V.; Tiwari, S.K.; Setty, D.S.; Kalyanakrishnan, G.; Saibaba, N.

2015-01-01

Coagulation-flocculation, membrane separation and ion-exchange are traditional methods for treatment of radioactive wastewater generated primarily from the front end processes of the fuel cycle. Electrocoagulation presents a robust and novel alternative to conventional coagulation process. The present study involves the establishment of electrocoagulation as a treatment process for thorium bearing non-process effluents in batch mode. This involved an electrolytic reactor with iron electrodes. The non-process effluent was subjected to coagulation and floatation by Fe(II) ions dissolved from the anode with the resultant flocs floating on the surface after being captured by hydrogen gas bubbles generated at the cathode. The effect of various operational parameters like initial pH, residence time, current density and initial thorium concentration on the removal efficiency was investigated. Maximum decontamination factor obtained was of the order of 10 4 . (author)

Preliminary study on characteristics of equilibrium thorium fuel cycle of BWR

International Nuclear Information System (INIS)

Waris, A.; Kurniadi, R.; Su'ud, Z.; Permana, S.

2007-01-01

One of the main objectives behind the transuranium recycling ideas is not merely to utilize natural resource that is uranium much more efficiently, but to reduce the environmental impact of the radio-toxicity of the nuclear spent fuel. Beside uranium resource, there is thorium which has three times abundance compared to that of uranium which can be utilized as nuclear fuel. On top of that thorium is believed to have less radio-toxicity of spent fuel since its produce smaller amount of higher actinides compared to that of uranium. However, the studies on the thorium utilization in nuclear reactor in particular in light water reactors (LWR) are not performed intensively yet. Therefore, the aim of the present study is to evaluate the characteristics of thorium fuel cycle in LWR, especially boiling water reactor (BWR). To conduct the comprehensive investigations we have employed the equilibrium burnup model (1-3). The equilibrium burnup model is an alternative powerful method since its can handle all possible generated nuclides in any nuclear system. Moreover, this method is a simple time independent method. Hence the equilibrium burnup method could be very useful for evaluating and forecasting the characteristics of any nuclear fuel cycle, even the strange one, e.g. all nuclides are confined in the reactor1). We have employed 1368 nuclides in the equilibrium burnup calculation where 129 of them are heavy metals (HMs). This burnup code then is coupled with SRAC cell calculation code by using PIJ module to compose an equilibrium-cell burnup code. For cell calculation, 26 HMs, 66 fission products (FPs) and one pseudo FP have been utilized. The JENDL 3.2 library has been used in this study. References: 1. A. Waris and H. Sekimoto, 'Characteristics of several equilibrium fuel cycles of PWR', J. Nucl. Sci. Technol., 38, p.517-526, 2001 2. A. Waris, H. Sekimoto, and G. Kastchiev, Influence of Moderator-to-Fuel Volume Ratio on Pu and MA Recycling in Equilibrium Fuel Cycles of

Matrix supported tailored polymer for solid phase extraction of fluoride from variety of aqueous streams

International Nuclear Information System (INIS)

Thakur, Neha; Kumar, Sanjukta A.; Wagh, D.N.; Das, Sadananda; Pandey, Ashok K.; Kumar, Sangita D.; Reddy, A.V.R.

2012-01-01

Highlights: ► Th complexed with poly (bis[2-(methacryloyloxy)-ethyl]phosphate) as tailored polymer membranes. ► Membranes offered high capacity and selectivity for fluoride in aqueous media. ► Quantitative uptake (80 ± 5%) of fluoride. ► Fast sorption kinetics. ► Reusability of polymer membranes. - Abstract: Fluoride related health hazards (fluorosis) are a major environmental problem in many regions of the world. It affects teeth; skeleton and its accumulation over a long period can lead to changes in the DNA structure. It is thus absolutely essential to bring down the fluoride levels to acceptable limits. Here, we present a new inorganic–organic hybrid polymer sorbent having tailored fixed-sites for fluoride sorption. The matrix supported poly (bis[2-(methacryloyloxy)-ethyl]phosphate) was prepared by photo-initiator induced graft-polymerization in fibrous and microporous (sheet) host poly(propylene) substrates. These substrates were conditioned for selective fluoride sorption by forming thorium complex with phosphate groups on bis[2-methacryloyloxy)-ethyl] phosphate (MEP). These tailored sorbents were studied for their selectivity towards fluoride in aqueous media having different chemical conditions. The fibrous sorbent was found to take up fluoride with a faster rate (15 min for ≈76% sorption) than the sheet sorbent. But, the fluoride loading capacity of sheet sorbent (4320 mg kg −1 ), was higher than fibrous and any other sorbent reported in the literature so far. The sorbent developed in the present work was found to be reusable after desorption of fluoride using NaOH solution. It was tested for solid phase extraction of fluoride from natural water samples.

Application of the Alternative Traditional and Selective Precipitation Routes for Recovery of High Grade Thorium Concentrates from Egyptian Crude Monazite Sand

International Nuclear Information System (INIS)

Helaly, O.S.

2017-01-01

Process flow sheet selection for thorium separation in relatively high grade concentrate from Egyptian crude monazite sand was carried out. Traditional selective leaching and precipitation routes were applied after sulfuric acid digestion upon Egyptian crude monazite for this purpose. The resultant hot grey sulfate paste from monazite digestion was firstly cooled to ambient temperature then leached by normal water into two successive stages. The first leach solution contained most of the thorium which represents about 88% of the present thorium and its concentration in the liquor reached 4.5 g Th/l. This liquor also contains most of the free acids and major of impurities especially iron (more than 6.3 g Fe/l). Different routes were tested to evaluate the suitable conditions that verify maximum recovery of thorium from such monazite sulfate solution and producing relatively high grade concentrate. Two different possible traditional and selective methods were involved, namely; thorium initial precipitation with rare earth elements as double sulfate or its precipitation as phosphate through acidity control at ph 1.1 which seems to be the simple, brief and convenient route to accomplish this purpose. Further separation and/or upgrading of thorium from these precipitates (after conversion to hydroxides or without) were conducted through re-dissolution in hydrochloric acid and re-precipitation with different selective reagents in the form of hydroxide, oxalate or fluoride was also included. The target was accomplished through thorium co-precipitation with light rare earth elements as double sulfate, followed by its recovery from this fraction, where a concentrate of grade 68.3% was produced

Contribution of lead and thorium to the history of the Oklo reactors

International Nuclear Information System (INIS)

Devillers, C.; Menes, J.

1978-01-01

The authors report the results of measuring lead and thorium in a series of representative samples of the superconcentrations of uranium found in the Oklo mineralization. Interpretation of the data reveals the complexity of the history of lead in the deposit, but makes it possible to derive a number of important facts, namely early disturbance and recent, massive remobilization of lead. One is led to conclude that the date of the uranium emplacement may be greater than 1900 million years. The absence of high thorium contents in the ''normal'' rich ore confirms the importance of dating the nuclear reaction on the basis of the Th/U balance. This determination, which draws on the same set of data as for the Nd/U balance, gives a mean value close to 1930 million years. (author)

Performance of Energy Multiplier Module (EM2) with long-burn thorium fuel cycle

International Nuclear Information System (INIS)

Choi, Hangbok; Schleicher, Robert; Gupta, Puja

2015-01-01

Energy Multiplier Module (EM 2 ) is a helium-cooled fast reactor being developed by General Atomics for the 21 st century grid. It is designed as a modular plant with a net electric output of 265 MWe with an evaporative heat sink and 240 MWe with an air-cooled heat sink. EM 2 core performance is examined for the baseline loading of low-enriched uranium (LEU) as fissile material with depleted uranium (DU) as fertile material and compared to the alternate LEU with thorium loading. The latter has two options: a heterogeneous loading of thorium fuel in the place of DU that produces a longer fuel cycle, and homogeneously mixed thorium-uranium fuel loading. Compared to the baseline LEU/DU core, the cycle length of both thorium options is reduced due to higher neutron absorptions by thorium. However, for both, heterogeneous and homogenous thorium loading options, the fuel cycle length is over 24 years without refueling or reshuffling of fuel assemblies. The physics properties of the EM 2 thorium core are close to those of the baseline core which constitute low excess reactivity, negative fuel temperature coefficient, and very small void reactivity. However, unlike the case of baseline EM 2 , the homogeneous thorium fuel loading provides additional advantage in reducing the power peaking of the core, which in turn reduces the cladding material neutron damage rate by 23%. It is interpreted that the relatively slow 233 U buildup as compared to 239 Pu for baseline core retards reactivity increase without the need for a complicated fuel loading pattern of the heterogeneous fuel loading, while maintaining the peak power density low. Therefore both the heterogeneous and homogeneous thorium loading options will be feasible in the EM 2

Molten salt reactors and possible scenarios for future nuclear power deployment

International Nuclear Information System (INIS)

Merle-Lucotte, E.; Mathieu, L.; Heuer, D.; Loiseaux, J. M.; Billebaud, A.; Brissot, R.; David, S.; Garzenne, C.; Laulan, O.; Le Brun, C.; Lecarpentier, D.; Liatard, E.; Meplan, O.; Michel-Sendis, F.; Nuttin, A.; Perdu, F.

2004-01-01

An important fraction of the nature energy demand may be satisfied by nuclear power. In this context, the possibilities of worldwide nuclear deployment are studied. We are convinced that the Molten Salt Reactors may play a central role in this deployment. The Molten Salt Reactor needs to be coupled to a reprocessing unit in order to extract the Fission Products which poison the core. The efficiency of this reprocessing has a crucial influence on reactor behavior especially for the breeding ratio. The Molten Salt Breeder Reactor project was based on an intensive reprocessing for high breeding purposes. A new concept of Thorium Molten Salt Reactor is presented here. Including this new concept in the worldwide nuclear deployment, to satisfy these power needs, we consider three typical scenarios, based on three reactor types: Pressurized Water Reactor, Fast Neutron Reactor and Thorium Molten Salt Reactor. The aim of this paper is to demonstrate, in a first hand that a Thorium Molten Salt Reactor can be realistic, with correct temperature coefficients and at least iso-breeder with slow reprocessing and new geometry; on the other hand that such Molten Salt Reactors enable a successful nuclear deployment, while minimizing fuel and waste management problems. (authors)

The resonance integral of thorium metal rods

Energy Technology Data Exchange (ETDEWEB)

Hellstrand, E; Weitman, J

1960-03-15

The resonance integral for thorium metal rods of different diameters has been determined by the activation method. The irradiations took place in the central channel of the reactor R1, where the energy dependence of the neutron flux had earlier been investigated with a fast chopper up to about 1 keV. The absolute calibration was made with gold as a standard. The true resonance integral for gold was taken from the literature as 1,500 {+-} 35 b. The experimental values for thorium were fitted to two alternative expressions with the following results: RI = (1.70 + 15.9{radical}(S/M)) {+-} 5.5%; RI 17.3{radical}(S/M + 0.06) {+-} 5.5 %. The measurements were made for S/M values in the range 0.14 - 0.87 cm{sup 2}/g. The main contribution to the margin of errors arises from the uncertainties in the cross sections used and in the correction for the departure of the neutron energy distribution from the 1/E form.

First-principles study of point defects in thorium carbide

International Nuclear Information System (INIS)

Pérez Daroca, D.; Jaroszewicz, S.; Llois, A.M.; Mosca, H.O.

2014-01-01

Thorium-based materials are currently being investigated in relation with their potential utilization in Generation-IV reactors as nuclear fuels. One of the most important issues to be studied is their behavior under irradiation. A first approach to this goal is the study of point defects. By means of first-principles calculations within the framework of density functional theory, we study the stability and formation energies of vacancies, interstitials and Frenkel pairs in thorium carbide. We find that C isolated vacancies are the most likely defects, while C interstitials are energetically favored as compared to Th ones. These kind of results for ThC, to the best authors’ knowledge, have not been obtained previously, neither experimentally, nor theoretically. For this reason, we compare with results on other compounds with the same NaCl-type structure

First-principles study of point defects in thorium carbide

Energy Technology Data Exchange (ETDEWEB)

Pérez Daroca, D., E-mail: pdaroca@tandar.cnea.gov.ar [Gerencia de Investigación y Aplicaciones, Comisión Nacional de Energía Atómica, Av. General Paz 1499, (1650) San Martin, Buenos Aires (Argentina); Consejo Nacional de Investigaciones Científicas y Técnicas, (1033) Buenos Aires (Argentina); Jaroszewicz, S. [Gerencia de Investigación y Aplicaciones, Comisión Nacional de Energía Atómica, Av. General Paz 1499, (1650) San Martin, Buenos Aires (Argentina); Instituto de Tecnología Jorge A. Sabato, UNSAM-CNEA, Av. General Paz 1499, (1650) San Martin, Buenos Aires (Argentina); Llois, A.M. [Gerencia de Investigación y Aplicaciones, Comisión Nacional de Energía Atómica, Av. General Paz 1499, (1650) San Martin, Buenos Aires (Argentina); Consejo Nacional de Investigaciones Científicas y Técnicas, (1033) Buenos Aires (Argentina); Mosca, H.O. [Gerencia de Investigación y Aplicaciones, Comisión Nacional de Energía Atómica, Av. General Paz 1499, (1650) San Martin, Buenos Aires (Argentina); Instituto de Tecnología Jorge A. Sabato, UNSAM-CNEA, Av. General Paz 1499, (1650) San Martin, Buenos Aires (Argentina)

2014-11-15

Thorium-based materials are currently being investigated in relation with their potential utilization in Generation-IV reactors as nuclear fuels. One of the most important issues to be studied is their behavior under irradiation. A first approach to this goal is the study of point defects. By means of first-principles calculations within the framework of density functional theory, we study the stability and formation energies of vacancies, interstitials and Frenkel pairs in thorium carbide. We find that C isolated vacancies are the most likely defects, while C interstitials are energetically favored as compared to Th ones. These kind of results for ThC, to the best authors’ knowledge, have not been obtained previously, neither experimentally, nor theoretically. For this reason, we compare with results on other compounds with the same NaCl-type structure.

ZIRCONIUM-CLADDING OF THORIUM

Science.gov (United States)

Beaver, R.J.

1961-11-21

A method of cladding thorium with zirconium is described. The quality of the bond achieved between thorium and zirconium by hot-rolling is improved by inserting and melting a thorium-zirconium alloy foil between the two materials prior to rolling. (AEC)

Gas Reactor International Cooperative Program. Interim report. Construction and operating experience of selected European Gas-Cooled Reactors

International Nuclear Information System (INIS)

1978-09-01

The construction and operating experience of selected European Gas-Cooled Reactors is summarized along with technical descriptions of the plants. Included in the report are the AVR Experimental Pebble Bed Reactor, the Dragon Reactor, AGR Reactors, and the Thorium High Temperature Reactor (THTR). The study demonstrates that the European experience has been favorable and forms a good foundation for the development of Advanced High Temperature Reactors

Design study of Thorium-232 and Protactinium-231 based fuel for long life BWR

Energy Technology Data Exchange (ETDEWEB)

Trianti, N.; Su' ud, Z.; Riyana, E. S. [Nuclear Physics and Biophysics Research Division Department of Physics - Institut Teknologi Bandung (ITB) Jalan Ganeca 10 Bandung 40132 (Indonesia)

2012-06-06

A preliminary design study for the utilization of thorium added with {sup 231}Pa based fuel on BWR type reactor has been performed. In the previous research utilization of fuel based Thorium-232 and Uranium-233 show 10 years operation time with maximum excess-reactivity about 4.075% dk/k. To increase reactor operation time and reduce excess-reactivity below 1% dk/k, Protactinium (Pa-231) is used as Burnable Poison. Protactinium-231 has very interesting neutronic properties, which enable the core to reduce initial excess-reactivity and simultaneously increase production of {sup 233}U to {sup 231}Pa in burn-up process. Optimizations of the content of {sup 231}Pa in the core enables the BWR core to sustain long period of operation time with reasonable burn-up reactivity swing. Based on the optimization of fuel element composition (Th and Pa) in various moderation ratio we can get reactor core with longer operation time, 20 {approx} 30 years operation without fuel shuffling or refuelling, with average power densities maximum of about 35 watt/cc, and maximum excess-reactivity 0.56% dk/k.

Control rod studies for alternative fuel cycles in the GA 1160 MW(e) high temperature reactor

Energy Technology Data Exchange (ETDEWEB)

Neef, H. J.

1975-06-15

The control system, which is investigated in this paper for both the low enriched uranium high enriched uranium/thorium fuel cycles, has been developed to control the General Atomics (GA) thorium fuel cycle 1160 MW(e) reactor. It has been shown in this investigation that its effectiveness in the low enriched and subsequent thorium cycle switch-over reactor is equivalent to the effectiveness in the thorium cycle. The shutdown margin in the low enriched core is even higher compared to the thorium core, mainly due to the presence of Pa-233 in the thorium cycle. As long as the fuel cycle for the thorium cycle is not closed with the recycling of U-233, the low enriched cycle will offer an attractive alternative. It was found that the GA 1160 MW(e) control system has enough built-in control rod capacity to accommodate the low enriched uranium cycle and to perform a later switch-over to a thorium-based fuel cycle.

Industrial and natural nuclear reactors; Industrielle und natuerliche Kernreaktoren

Energy Technology Data Exchange (ETDEWEB)

Binnewies, Michael [Hannover Univ. (Germany); Willner, Helge; Woenckhaus, Juergen

2015-08-15

As described in the preceding article, all elements with atomic masses above that of iron and also the radioactive elements thorium and uranium have been formed by a supernova star explosion. Their long-lived isotopes of thorium and uranium are now distributed in the earth crust. The chemistry of uranium and thorium is of less importance, but these elements can be used to produce enormous amounts of energy in nuclear power stations. It will be described how it works. Surprisingly, small natural nuclear reactors were producing heat during hundreds of thousand years. Subsequently, we are dealing with this phenomenon, the principle of nuclear fission, the different types of nuclear reactors, security aspects and new developments.

The Dragon reactor experiment

International Nuclear Information System (INIS)

Anon.

1976-01-01

The concept on which the Dragon Reactor Experiment was based was evolved at the Atomic Energy Research Establishment at Harwell in 1956, and in February of that year a High Temperature Gas- cooled Reactor Project Group was set up to study the feasibility of a helium-cooled reactor with a graphite or beryllium moderator, and with the emphasis on the thorium fuel cycle [af

Review of thorium-U233 cycle thermal reactor benchmark studies (AWBA Development Program)

International Nuclear Information System (INIS)

Ullo, J.J.; Hardy, J. Jr.; Steen, N.M.

1980-03-01

A survey is made of existing integral experiments for U233 systems and thorium-uranium based fuel systems. The aim is to understand to what extent they give a consistent test of ENDF/B-IV nuclear data. A principal result is that ENDF/B-IV leads to an underprediction of neutron leakage. Results from testing alternate thorium data sets are presented. For one evaluation due to Leonard, the results depict a possible growing discrepancy between measured integral parameters such as rho 02 and I 232 and the differential data, which underpredicts these parameters. Sensitivities to other nuclear data components, notably the fission neutron spectrum, were determined. A new harder U233 spectrum significantly reduces a bias trend in K/sub eff/ vs leakage

Transmutation, Burn-Up and Fuel Fabrication Trade-Offs in Reduced-Moderation Water Reactor Thorium Fuel Cycles - 13502

Energy Technology Data Exchange (ETDEWEB)

Lindley, Benjamin A.; Parks, Geoffrey T. [University of Cambridge, Cambridge (United Kingdom); Franceschini, Fausto [Westinghouse Electric Company LLC, Cranberry Township, PA (United States)

2013-07-01

Multiple recycle of long-lived actinides has the potential to greatly reduce the required storage time for spent nuclear fuel or high level nuclear waste. This is generally thought to require fast reactors as most transuranic (TRU) isotopes have low fission probabilities in thermal reactors. Reduced-moderation LWRs are a potential alternative to fast reactors with reduced time to deployment as they are based on commercially mature LWR technology. Thorium (Th) fuel is neutronically advantageous for TRU multiple recycle in LWRs due to a large improvement in the void coefficient. If Th fuel is used in reduced-moderation LWRs, it appears neutronically feasible to achieve full actinide recycle while burning an external supply of TRU, with related potential improvements in waste management and fuel utilization. In this paper, the fuel cycle of TRU-bearing Th fuel is analysed for reduced-moderation PWRs and BWRs (RMPWRs and RBWRs). RMPWRs have the advantage of relatively rapid implementation and intrinsically low conversion ratios. However, it is challenging to simultaneously satisfy operational and fuel cycle constraints. An RBWR may potentially take longer to implement than an RMPWR due to more extensive changes from current BWR technology. However, the harder neutron spectrum can lead to favourable fuel cycle performance. A two-stage fuel cycle, where the first pass is Th-Pu MOX, is a technically reasonable implementation of either concept. The first stage of the fuel cycle can therefore be implemented at relatively low cost as a Pu disposal option, with a further policy option of full recycle in the medium term. (authors)

Transmutation, Burn-Up and Fuel Fabrication Trade-Offs in Reduced-Moderation Water Reactor Thorium Fuel Cycles - 13502

International Nuclear Information System (INIS)

Lindley, Benjamin A.; Parks, Geoffrey T.; Franceschini, Fausto

2013-01-01

Multiple recycle of long-lived actinides has the potential to greatly reduce the required storage time for spent nuclear fuel or high level nuclear waste. This is generally thought to require fast reactors as most transuranic (TRU) isotopes have low fission probabilities in thermal reactors. Reduced-moderation LWRs are a potential alternative to fast reactors with reduced time to deployment as they are based on commercially mature LWR technology. Thorium (Th) fuel is neutronically advantageous for TRU multiple recycle in LWRs due to a large improvement in the void coefficient. If Th fuel is used in reduced-moderation LWRs, it appears neutronically feasible to achieve full actinide recycle while burning an external supply of TRU, with related potential improvements in waste management and fuel utilization. In this paper, the fuel cycle of TRU-bearing Th fuel is analysed for reduced-moderation PWRs and BWRs (RMPWRs and RBWRs). RMPWRs have the advantage of relatively rapid implementation and intrinsically low conversion ratios. However, it is challenging to simultaneously satisfy operational and fuel cycle constraints. An RBWR may potentially take longer to implement than an RMPWR due to more extensive changes from current BWR technology. However, the harder neutron spectrum can lead to favourable fuel cycle performance. A two-stage fuel cycle, where the first pass is Th-Pu MOX, is a technically reasonable implementation of either concept. The first stage of the fuel cycle can therefore be implemented at relatively low cost as a Pu disposal option, with a further policy option of full recycle in the medium term. (authors)

Basic analysis and a comparison of the characteristics GCFRs and the LMFBR with the thorium cycle in one-group diffusion theory

International Nuclear Information System (INIS)

Sabundjian, G.; Ishiguro, Y.

1991-09-01

A preliminary study of neutronics of thorium cycle fast breeder reactor has been done using simplified reactor models and analyses methods with the aim of finding a type of breeder reactor suitable for an efficient utilization of thorium that is abundant in Brazil. Basic methods of cross section processing and reactor calculation are studied and applied to analyse breeding characteristics of GCFRs and LMFBRs. The GCFR is fueled with oxide pins and cooled with helium. The LMFBR is fueled with thin metallic pins to achieve high power densities. Neutronics characteristics are determined as functions of the average power density and the fuel volume fraction. Results show that a high power density and a high fuel volume fraction are desirable to achieve short doubling times, that the GCFR is inferior to the LMFBR in regard to the doubling time and that the LMFBR can achieve reactor doubling times ten years with an average power density of ∼ 600MW/m 3 and fuel volume fraction of 40%. (author)

Thermodynamic investigation of fluoride salts for nuclear energy production

International Nuclear Information System (INIS)

Beilmann, Markus

2013-01-01

In this work thermodynamic properties of molten fluoride salts and salt mixtures are investigated. Fluoride salts have advantageous properties to be used in energy producing systems based on the conversion from heat to energy like i.e in Molten Salt Reactors. For this purpose it is very important to have detailed information about the heat capacity of the pure salts and salt mixtures. To get a better understanding about the heat capacity in mixtures drop calorimetry measurements of mixtures of LiF with other alkali fluorides were conducted and compared. The investigation of fluoride salts at elevated temperatures is complicated by the fact that fluoride vapour is aggressive to many materials. In order to protect our sensitive measurement equipment the salt samples were encapsulated in nickel crucibles using a laser welding technique and afterwards the whole nickel capsule was measured. This method was verified by the measurement of unmixed CsF and KF where in both examples an excellent agreement with literature data was obtained. Afterwards various intermediate compositions of the systems LiF-KF, LiF-CsF and LiF-RbF were investigated and a general trend according to the difference in cation radii could be established. In combination with literature data for the LiF-NaF system the heat capacity of the liquid state follows the order LiF-NaF 2 -LaF 3 phase diagram was obtained. With the help of mathematical models the phase diagrams can be calculated and also higher order systems can be predicted. The LiF-NaF-CaF 2 -LaF 3 system was calculated with the classical polynomial model and the quasi-chemical model in parallel in order to evaluate which of the two models provide a better extrapolation to higher order systems (ternary or quaternary) based on the related binary systems. The two models behaved very similar at the investigated system and the quasi-chemical model was chosen for further assessments of phase diagrams. This model was selected, since it considers the

Nuclear data covariances and sensitivity analysis, validation of a methodology based on the perturbation theory; application to an innovative concept: the molten thorium salt fueled reactor; Analyses de sensibilite et d'incertitude de donnees nucleaires. Contribution a la validation d'une methodologie utilisant la theorie des perturbations; application a un concept innovant: reacteur a sels fondus thorium a spectre epithermique

Energy Technology Data Exchange (ETDEWEB)

Bidaud, A

2005-10-15

Neutron transport simulation of nuclear reactors is based on the knowledge of the neutron-nucleus interaction (cross-sections, fission neutron yields and spectra...) for the dozens of nuclei present in the core over a very large energy range (fractions of eV to several MeV). To obtain the goal of the sustainable development of nuclear power, future reactors must have new and more strict constraints to their design: optimization of ore materials will necessitate breeding (generation of fissile material from fertile material), and waste management will require transmutation. Innovative reactors that could achieve such objectives - generation IV or ADS (accelerator driven system) - are loaded with new fuels (thorium, heavy actinides) and function with neutron spectra for which nuclear data do not benefit from 50 years of industrial experience, and thus present particular challenges. After validation on an experimental reactor using an international benchmark, we take classical reactor physics tools along with available nuclear data uncertainties to calculate the sensitivities and uncertainties of the criticality and temperature coefficient of a thorium molten salt reactor. In addition, a study based on the important reaction rates for the calculation of cycle's equilibrium allows us to estimate the efficiency of different reprocessing strategies and the contribution of these reaction rates on the uncertainty of the breeding and then on the uncertainty of the size of the reprocessing plant. Finally, we use this work to propose an improvement of the high priority experimental request list. (author)

PWR core design, neutronics evaluation and fuel cycle analysis for thorium-uranium breeding recycle

International Nuclear Information System (INIS)

Bi, G.; Liu, C.; Si, S.

2012-01-01

This paper was focused on core design, neutronics evaluation and fuel cycle analysis for Thorium-Uranium Breeding Recycle in current PWRs, without any major change to the fuel lattice and the core internals, but substituting the UOX pellet with Thorium-based pellet. The fuel cycle analysis indicates that Thorium-Uranium Breeding Recycle is technically feasible in current PWRs. A 4-loop, 193-assembly PWR core utilizing 17 x 17 fuel assemblies (FAs) was taken as the model core. Two mixed cores were investigated respectively loaded with mixed reactor grade Plutonium-Thorium (PuThOX) FAs and mixed reactor grade 233 U-Thorium (U 3 ThOX) FAs on the basis of reference full Uranium oxide (UOX) equilibrium-cycle core. The UOX/PuThOX mixed core consists of 121 UOX FAs and 72 PuThOX FAs. The reactor grade 233 U extracted from burnt PuThOX fuel was used to fabrication of U 3 ThOX for starting Thorium-. Uranium breeding recycle. In UOX/U 3 ThOX mixed core, the well designed U 3 ThOX FAs with 1.94 w/o fissile uranium (mainly 233 U) were located on the periphery of core as a blanket region. U 3 ThOX FAs remained in-core for 6 cycles with the discharged burnup achieving 28 GWD/tHM. Compared with initially loading, the fissile material inventory in U 3 ThOX fuel has increased by 7% via 1-year cooling after discharge. 157 UOX fuel assemblies were located in the inner of UOX/U 3 ThOX mixed core refueling with 64 FAs at each cycle. The designed UOX/PuThOX and UOX/U 3 ThOX mixed core satisfied related nuclear design criteria. The full core performance analyses have shown that mixed core with PuThOX loading has similar impacts as MOX on several neutronic characteristic parameters, such as reduced differential boron worth, higher critical boron concentration, more negative moderator temperature coefficient, reduced control rod worth, reduced shutdown margin, etc.; while mixed core with U 3 ThOX loading on the periphery of core has no visible impacts on neutronic characteristics compared

Comparison of open cycles of uranium and mixed oxides of thorium-uranium using advanced reactors; Comparação de ciclos abertos de urânio e óxidos mistos de tório-urânio utilizando reatores avançados

Energy Technology Data Exchange (ETDEWEB)

Gonçalves, Letícia C.; Maiorino, José R., E-mail: goncalves.leticiac@gmail.com [Universidade Federal do ABC (UFABC), Santo André, SP (Brazil). Centro de Engenharia, Modelagem e Ciências Sociais Aplicadas

2017-07-01

A comparative study of the mass balance and production costs of uranium oxide fuels was carried out for an AP1000 reactor and thorium-uranium mixed oxide in a reactor proposal using thorium called AP-Th1000. Assuming the input mass values for a fuel load the average enrichment for both reactors as well as their feed mass was determined. With these parameters, the costs were calculated in each fuel preparation process, assuming the prices provided by the World Nuclear Association. The total fuel costs for the two reactors were quantitatively compared with 18-month open cycle. Considering enrichment of 20% for the open cycle of mixed U-Th oxide fuel, the total uranium consumption of this option was 50% higher and the cost due to the enrichment was 70% higher. The results show that the use of U-Th mixed oxide fuels can be advantageous considering sustainability issues. In this case other parameters and conditions should be investigated, especially those related to fuel recycling, spent fuel storage and reduction of the amount of transuranic radioactive waste.

Performance Analysis Review of Thorium TRISO Coated Particles during Manufacture, Irradiation and Accident Condition Heating Tests

International Nuclear Information System (INIS)

2015-03-01

Thorium, in combination with high enriched uranium, was used in all early high temperature reactors (HTRs). Initially, the fuel was contained in a kernel of coated particles. However, particle quality was low in the 1960s and early 1970s. Modern, high quality, tristructural isotropic (TRISO) fuel particles with thorium oxide and uranium dioxide (UO 2 ) had been manufactured since 1978 and were successfully demonstrated in irradiation and accident tests. In 1980, HTR fuels changed to low enriched uranium UO 2 TRISO fuels. The wide ranging development and demonstration programme was successful, and it established a worldwide standard that is still valid today. During the process, results of the thorium work with high quality TRISO fuel particles had not been fully evaluated or documented. This publication collects and presents the information and demonstrates the performance of thorium TRISO fuels.This publication is an outcome of the technical contract awarded under the IAEA Coordinated Research Project on Near Term and Promising Long Term Options for Deployment of Thorium Based Nuclear Energy, initiated in 2012. It is based on the compilation and analysis of available results on thorium TRISO coated particle performance in manufacturing and during irradiation and accident condition heating tests

Protactinium-231 found in natural thorium irradiated in JMTR

International Nuclear Information System (INIS)

Suzuki, Susumu; Mitsugashira, Toshiaki; Hara, Mitsuo; Satoh, Isamu; Shiokawa, Yoshinobu; Satoh, Michiko

1987-01-01

Natural thorium dioxides, which differed in the content of 230 Th, were irradiated in JMTR(Japan Material Testing Reactor). 232 U, 233 U, 231 Pa, 233 Pa, and remaining Th were measured radiometrically. High production of 231 Pa and high consumption of 230 Th were observed and it was necessary to assume large resonance capture of 230 Th in order to explain the production of 231 Pa and the consumption of 230 Th. (author)

An overview of the potential of the CANDU reactor as a thermal breeder

International Nuclear Information System (INIS)

Slater, J.B.

1977-02-01

This paper is concerned with the use of thorium as a fuel in the existing CANDU concept. The neutron balance of the reactor core is analyzed and an assessment is made of the potential for development of a thermal 'breeder' reactor system. It is concluded that while the SSET cycle (i.e. self-sufficient equilibrium thorium cycle) appears feasible, there is little potential for developing a significant 'breeding' fuel cycle if current reactor operating capability and capital costs are to be maintained. (author)

Model for the behaviour of thorium and uranium fuels at pelletization

International Nuclear Information System (INIS)

Ferreira Neto, Ricardo Alberto

2000-11-01

In this work, a model for the behaviour of thorium-uranium-mixed oxide microspheres in the pelletizing process is presented. This model was developed in a program whose objective was to demonstrate the viability of producing fissile material through the utilization of thorium in pressurized water reactors. This is important because it allows the saving of the strategic uranium reserves, and makes it possible the nuclear utilization of the large brazilian thorium reserves. The objective was to develop a model for optimizing physical properties of the microspheres, such as density, fracture strength and specific surface, so as to produce fuel pellets with microstructure, density, open porosity and impurity content, in accordance with the fuel specification. And, therefore, to adjust the sol-gel processing parameters in order to obtain these properties, and produce pellets with an optimized microstructure, adequate to a stable behaviour under irradiation. The model made it clear that to achieve this objective, it is necessary to produce microspheres with density and specific surface as small as possible. By changing the sol-gel processing parameters, microspheres with the desired properties were produced, and the model was experimentally verified by manufacturing fuel pellets with optimized microstructures, density, open porosity and impurity content, meeting the specifications for this new nuclear fuel for pressurized water reactors. Furthermore it was possible to obtain mathematical expressions that enables to calculate from the microspheres properties and the utilized compaction pressure, the sinter density that will be obtained in the sintered pellet and the necessary compaction pressure to reach the sintered density specified for the fuel. (author)

Thorium Fuel Options for Sustained Transuranic Burning in Pressurized Water Reactors - 12381

Energy Technology Data Exchange (ETDEWEB)

Rahman, Fariz Abdul; Lee, John C. [University of Michigan, Ann Arbor, MI (United States); Franceschini, Fausto; Wenner, Michael [Westinghouse Electric Company LLC, Cranberry Township, PA (United States)

2012-07-01

As described in companion papers, Westinghouse is proposing the adoption of a thorium-based fuel cycle to burn the transuranics (TRU) contained in the current Used Nuclear Fuel (UNF) and transition towards a less radio-toxic high level waste. A combination of both light water reactors (LWR) and fast reactors (FR) is envisaged for the task, with the emphasis initially posed on their TRU burning capability and eventually to their self-sufficiency. Given the many technical challenges and development times related to the deployment of TRU burners fast reactors, an interim solution making best use of the current resources to initiate burning the legacy TRU inventory while developing and testing some technologies of later use is desirable. In this perspective, a portion of the LWR fleet can be used to start burning the legacy TRUs using Th-based fuels compatible with the current plants and operational features. This analysis focuses on a typical 4-loop PWR, with 17x17 fuel assembly design and TRUs (or Pu) admixed with Th (similar to U-MOX fuel, but with Th instead of U). Global calculations of the core were represented with unit assembly simulations using the Linear Reactivity Model (LRM). Several assembly configurations have been developed to offer two options that can be attractive during the TRU transmutation campaign: maximization of the TRU transmutation rate and capability for TRU multi-recycling, to extend the option of TRU recycling in LWR until the FR is available. Homogeneous as well as heterogeneous assembly configurations have been developed with various recycling schemes (Pu recycle, TRU recycle, TRU and in-bred U recycle etc.). Oxide as well as nitride fuels have been examined. This enabled an assessment of the potential for burning and multi-recycling TRU in a Th-based fuel PWR to compare against other more typical alternatives (U-MOX and variations thereof). Results will be shown indicating that Th-based PWR fuel is a promising option to multi-recycle and

Thorium research and development in Turkey

International Nuclear Information System (INIS)

Güngör, Görkem

2015-01-01

Turkey has a great potential regarding thorium resources. Thorium exploration activities have been done in the past mainly by state organizations for determining the thorium resources in Turkey. Thorium occurs as complex mineral together with barite, fluorite and rare earth elements (REE). The increase in global demand for REE creates the opportunity for REE production which will also produce thorium as a by-product. The development of nuclear energy program in Turkey provides the stimulus for research and development activities in nuclear technologies. The final declaration of the workshop emphasizes the importance of thorium reserves in Turkey and the necessity for thorium exploration and development activities in order to determine the feasibility of thorium mining and fuel cycle in Turkey. These activities should be conducted together with the development of technologies for separation of these complex minerals and purification of thorium, REE and other minerals to be utilized as commercial products. There are advanced academic research studies on thorium fuel cycle which should be supported by the industry in order to commercialize the results of these studies. Turkey should be integrated to international R and D activities on ADS which is expected to commercialize on medium term. The legislative framework should be developed in order to provide the industrial baseline for nuclear technologies independent from nuclear regulatory activities

A study of overseas research activities for thorium reactors and the need for the introduction of the domestic nuclear power

International Nuclear Information System (INIS)

Park, Dongwon; Park, Keunteag

2013-01-01

Many countries have been proceeding research actively in this area as highlighted these advantages but de facto, there are not official research activities in Korea. This paper is to analyze the current status of research in some countries and describe the possibilities introduce with necessity in Korea. Radiation and the radioactive waste, decay heat, loss of coolant accident that related with safety issue are always emerging as a problem of social acceptance of nuclear power plant. Proportion of U- 235 , uranium fuel is only 3-5% and the rest of U- 238 is discarded as all nuclear waste in accordance with 'Open Cycle.' Even if put to practical use thorium reactor, nuclear waste generated but can significantly reduce the toxicity nuclides of TRU and not only the decay heat that physical cause of Fukushima nuclear power plant accident does not occur but also do not need to worry about the LOCA. Our nuclear power plant have been operated very safety compared to Japan. Relative to unexpected operation stop status in terms of base 5 years previous of Fukushima nuclear accident are 0.5 based on average value in our nuclear power plants on the other hand 0.4 in total 17 units of nuclear power plant subsidiary Tokyo Electric Power co., Japan. It is similar to ours, and is similar to Kansai Electric Power Co. However, total reported incidents of non-severe accidents are much higher than ours. But that cannot be interpreted as the safety of our operating skills of nuclear power plant are excellent compared to other countries. For many people's anxiety about nuclear power plants operating after the Fukushima accident, nuclear operators emphasized the safety of our nuclear power plant with referring to the difference between PWR and BWR. Our nuclear power plant were complementary in many facilities depend on problems revealed at the Fukushima nuclear power plant. But it seems to be need for long-term research and development of next-generation nuclear power plant that safety

A study of uranium-thorium mixed lattices; Etude de reseaux mixtes uranium - thorium

Energy Technology Data Exchange (ETDEWEB)

Bacher, P; Eckert, R; Mazancourt, R de [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires

1957-07-01

Some subcritical experiments have been carried out during the charging of the pile G1 by introducing thorium bars in a regular lattice into the pile. The spreading out of these experiments over a period of three months has permitted: a) work on a pile gradually increasing in size and b) measurements on comparable charges in so far that they have either the same number of bars of thorium, or the same concentration of thorium. From the measurements at constant charge and at constant concentration, it is possible by extrapolation to determine the critical charges and concentrations. The values obtained have showed that the material Laplacian of the lattice depends linearly on the thorium concentration and must cancel out for a concentration T = 8.8 {+-} 0.3 per cent by volume. These results have been found, to a very good approximation, by a simple calculation. (author) [French] Des experiences sous-critiques ont ete effectuees au cours du chargement de la pile G1 en introduisant des barres de thorium reparties suivant un reseau regulier dans la pile. L'etalement de ces experiences sur trois mois a permis d'operer sur une pile de plus en plus grosse et de faire un grand nombre de mesures sur des chargements comparables par le fait qu'ils avaient soit le meme nombre de barres de thorium, soit la meme concentration en thorium. A partir des mesures a chargement constant et a concentration constante, il a ete possible de determiner par extrapolation les chargements et concentrations critiques. Les valeurs obtenues ont montre que le laplacien matiere moyen du reseau dependait lineairement de la concentration en thorium, et devrait s'annuler pour une concentration T = 8,8 {+-} 0,3% en volume. Ces resultats ont ete retrouves avec une tres bonne approximation par un calcul elementaire. (auteur)

Estimation of thorium intake due to consumption of vegetables by inhabitants of high background radiation area by INAA

International Nuclear Information System (INIS)

Sathyapriya, R.S.; Suma Nair; Prabhath, R.K.; Madhu Nair; Rao, D.D.

2012-01-01

A study was conducted to estimate the thorium concentration in locally grown vegetables in high background radiation area (HBRA) of southern coastal regions of India. Locally grown vegetables were collected from HBRA of southern coastal regions of India. Thorium concentration was quantified using instrumental neutron activation analysis. The samples were irradiated at CIRUS reactor and counted using a 40% relative efficiency HPGe detector coupled to MCA. The annual intake of thorium was evaluated using the consumption data provided by National Nutrition Monitoring Board. The daily intake of 232 Th from the four food categories (green leafy vegetables, others vegetables, roots and tubers, and fruits) ranged between 0.27 and 5.352 mBq d -1 . The annual internal dose due to ingestion of thorium from these food categories was 46.8 x 10 -8 for female and 58.6 x 10 -8 Sv y -1 for male. (author)

A study of the running-in period of a CANDU-PHW thorium converter

International Nuclear Information System (INIS)

Dormuth, K.W.; Lidstone, R.F.

1977-08-01

One of the concepts being studied as part of an evaluation of advanced fuel cycles for the Canadian nuclear power program is that of a Candu reactor whose initial fuel is a mixture of thorium and plutonium and whose bred uranium is recycled back to the same core with plutonium topping. From start-up of this reactor, when the fuel contains no uranium, to the attainment of equilibrium, when the uranium content of the feed fuel becomes constant, the core is in a transitional state because the composition of the feed fuel is changing. Since this so-called running-in period constitutes a large portion of the reactor life, it is essential that it be accounted for in fuel management calculations. The presence of the relatively long-lived intermediate nuclide, 233 Pa, in the thorium conversion chain complicates such calculations, because it causes the concentration of the important fissile isotope, 233 U, to depend rather strongly on flux history. A computational method based on the lattice code, WIMS, and the one-dimensional diffusion-depletion code, FEVER-7, has been developed and used to analyse the running-in period of a 1200 MWe (Th,Pu,U)O 2 -fuelled CANDU-PHW. (author)

Preconceptual design of a packed fluidized bed blanket for a fission suppressed thorium-fueled CTHR

International Nuclear Information System (INIS)

Chi, J.W.H.; Karbowski, J.S.; Chapin, D.L.

1981-01-01

This paper describes a thorium-fueled PFB blanket concept for a Commercial Tokamak Hybrid Reactor. A preliminary mechanical concept is presented and the results of neutronics, thermal-hydraulics and economics analyses are discussed. Futher work needed to design and advance the concept is recommended

An extraction method of uranium 233 from the thorium irradiates in a reactor core; Une methode d'extraction de l'uranium-233 a partir du thorium irradie dans une pile

Energy Technology Data Exchange (ETDEWEB)

Chesne, A; Regnaut, P [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires

1955-07-01

Description of the conditions of separation of the thorium, of the uranium 233 and of the protactinium 233 in hydrochloric solution by absorption then selective elution on anion exchange resin. A precipitation of the thorium by the oxalic acid permits the recuperation of the hydrochloric acid which is recycled, the main, raw material consumed being the oxalic acid. (authors) [French] Description des conditions de separation du thorium, de l'uranium 233 et du protactinium 233 en solution chlorhydrique par absorption puis elution selective sur resine echangeuse d'anions. Une precipitation du thoriun par l'acide oxalique permet la recuperation de l'acide chlorhydrique qui est recycle, la principale matiere premiere consommee etant l'acide oxalique. (auteurs)

Preparation of pyrolytic carbon coating on graphite for inhibiting liquid fluoride salt and Xe135 penetration for molten salt breeder reactor

International Nuclear Information System (INIS)

Song, Jinliang; Zhao, Yanling; He, Xiujie; Zhang, Baoliang; Xu, Li; He, Zhoutong; Zhang, DongSheng; Gao, Lina; Xia, Huihao; Zhou, Xingtai; Huai, Ping; Bai, Shuo

2015-01-01

Highlights: • Rough laminar pyrolytic carbon coating (RLPyC) is prepared by a fixed-bed method. • The salt-infiltration into IG-110 is 13.5%, less than 0.01% of RLPyC under 1.5 atm. • The helium diffusion coefficient of RLPyC coated graphite is 2.16 × 10 −8 cm 2 /s. • The coated graphite can inhibit the liquid fluoride salt and Xe 135 penetration. - Abstract: A fixed-bed deposition method was used to prepare rough laminar pyrolytic carbon coating (RLPyC) on graphite for inhibiting liquid fluoride salt and Xe 135 penetration during use in molten salt breeder reactor. The RLPyC coating possessed a graphitization degree of 44% and had good contact with graphite substrate. A high-pressure reactor was constructed to evaluate the molten salt infiltration in the isostatic graphite (IG-110, TOYO TANSO CO., LTD.) and RLPyC coated graphite under 1.01, 1.52, 3.04, 5.07 and 10.13 × 10 5 Pa for 12 h. Mercury injection and molten-salt infiltration experiments indicated the porosity and the salt-infiltration amount of 18.4% and 13.5 wt% under 1.52 × 10 5 Pa of IG-110, which was much less than 1.2% and 0.06 wt% under 10.13 × 10 5 Pa of the RLPyC, respectively. A vacuum device was constructed to evaluate the Xe 135 penetration in the graphite. The helium diffusion coefficient of RLPyC coated graphite was 2.16 × 10 −12 m 2 /s, much less than 1.21 × 10 −6 m 2 /s of the graphite. Thermal cycle experiment indicated the coatings possessed excellent thermal stability. The coated graphite could effectively inhibit the liquid fluoride salt and Xe 135 penetration

High temperature EXAFS experiments in molten actinide fluorides: The challenge of a triple containment cell for radioactive and aggressive liquids

Science.gov (United States)

Bessada, Catherine; Zanghi, Didier; Pauvert, Olivier; Maksoud, Louis; Gil-Martin, Ana; Sarou-Kanian, Vincent; Melin, Philippe; Brassamin, Séverine; Nezu, Atsushi; Matsuura, Haruaki

2017-10-01

An airtight double barrier cell with simple geometry has been developed for X-rays absorption measurements at high temperature in solid and molten actinide fluorides. The aim was both to improve the air tightness, to avoid any possible leakage and to maintain the high quality of the signal. The dimensions of the heating chamber were also constrained and minimized to be compatible with the limited space available usually on synchrotron beam lines and with a geometry suitable for absorption/diffraction measurements at high temperature. The design of the double barrier cell was also driven by the safety requirements in every experiment involving radioactive materials. The furnace itself was designed to ensure easy operating modes and disassembly, the aim being to consider the furnace as the ultimate containment. The cell has been tested with different molten fluorides up to more than 1000 °C, starting from non-radioactive LiF-ZrF4 mixtures in order to prove that the cell is absolutely airtight and that not any contamination of the environment occurs. Then it has been successfully applied to thorium fluoride- and uranium fluoride-alkali fluorides mixtures.

Analysis of Uranium and Thorium in Radioactive Wastes from Nuclear Fuel Cycle Process

International Nuclear Information System (INIS)

Gunandjar

2008-01-01

The assessment of analysis method for uranium and thorium in radioactive wastes generated from nuclear fuel cycle process have been carried out. The uranium and thorium analysis methods in the assessment are consist of Titrimetry, UV-VIS Spectrophotometry, Fluorimetry, HPLC, Polarography, Emission Spectrograph, XRF, AAS, Alpha Spectrometry and Mass Spectrometry methods. From the assessment can be concluded that the analysis methods of uranium and thorium content in radioactive waste for low concentration level using UV-VIS Spectrometry is better than Titrimetry method. While for very low concentration level in part per billion (ppb) can be used by Neutron Activation Analysis (NAA), Alpha Spectrometry and Mass Spectrometry. Laser Fluorimetry is the best method of uranium analysis for very low concentration level. Alpha Spectrometry and ICP-MS (Inductively Coupled Plasma Mass Spectrometry) methods for isotopic analysis are favourable in the precision and accuracy aspects. Comparison of the ICP-MS and Alpha Spectrometry methods shows that the both of methods have capability to determining of uranium and thorium isotopes content in the waste samples with results comparable very well, but the time of its analysis using ICP-MS method is faster than the Alpha Spectrometry, and also the cost of analysis for ICP-MS method is cheaper. NAA method can also be used to analyze the uranium and thorium isotopes, but this method needs the reactor facility and also the time of its analysis is very long. (author)

Fluoride absorption: independence from plasma fluoride levels

International Nuclear Information System (INIS)

Whitford, G.M.; Williams, J.L.

1986-01-01

The concept that there are physiologic mechanisms to homeostatically regulate plasma fluoride concentrations has been supported by results in the literature suggesting an inverse relationship between plasma fluoride levels and the absorption of the ion from the gastrointestinal tract of the rat. The validity of the relationship was questioned because of possible problems in the experimental design. The present work used four different methods to evaluate the effect of plasma fluoride levels on the absorption of the ion in rats: (i) the percentage of the daily fluoride intake that was excreted in the urine; (ii) the concentration of fluoride in femur epiphyses; (iii) the net areas under the time-plasma fluoride concentration curves after intragastric fluoride doses; and (iv) the residual amounts or fluoride in the gastrointestinal tracts after the intragastric fluoride doses. None of these methods indicated that plasma fluoride levels influence the rate or the degree or fluoride absorption. It was concluded that, unless extremely high plasma fluoride levels are involved (pharmacologic or toxic doses), the absorption of the ion is independent of plasma levels. The results provide further evidence that plasma fluoride concentrations are not homeostatically regulated

Use of fluoride systems for some fission product separation from residues of fast reactor spent fuel fluorination

International Nuclear Information System (INIS)

Shishkov, Yu.D.; Khomyakov, V.I.

1977-01-01

Investigated has been a possibility of the use of fluoride systems (acid nitrozyl fluoride and molten salts) for americium extraction from residues of fluorination of irradiated fuel containing mainly fluorides of rare earth compounds, alkali and alkaline earth elements. At treatment of fission product fluorides by acid nitrozyl fluoride only cesium and uranium fluorides dissolve, while americium and rare earth fluorides are practically non-soluble in it. The solubility of cesium, strontium, barium and fluorides of some other rare earth elements in molten cryolite at the temperature of 1000 deg C, Li-NaF and LiF-CaF 2 of eutectic content at 750 and 800 deg C are respectively 15-77 %. Cerium fluoride presents an exception, its solubility in cryolite being only 0.73%. At treatment of mixture of americium and lanthanum fluorides by molten salts in the weight ratio of 1:1, approximately 50% of lanthanum and 65-70% of americium turn into melt independent of the type of melt. The maximum melt output of americium is obtained at treatment of lanthanum and americium fluoride mixture by cryolite melt at the temperature of 1000 deg C. It is shown that the presence of rare earth of fluorides, except lanthanum fluoride, effect significantly of americium distribution over phases in the process of fluoride processing by the fluoride molten salts

Indian advanced nuclear reactors

International Nuclear Information System (INIS)

Saha, D.; Sinha, R.K.

2005-01-01

For sustainable development of nuclear energy, a number of important issues like safety, waste management, economics etc. are to be addressed. To do this, a number of advanced reactor designs as well as fuel cycle technologies are being pursued worldwide. The advanced reactors being developed in India are the AHWR and the CHTR. Both the reactors use thorium based fuel and have many passive features. This paper describes the Indian advanced reactors and gives a brief account of the international initiatives for the sustainable development of nuclear energy. (author)

An energy amplifier fluidized bed nuclear reactor concept

International Nuclear Information System (INIS)

Sefidvash, F.; Seifritz, W.

2001-01-01

The concept of a fluidized bed nuclear reactor driven by an energy amplifier system is described. The reactor has promising characteristics of inherent safety and passive cooling. The reactor can easily operate with any desired spectrum in order to be a plutonium burner or have it operate with thorium fuel cycle. (orig.) [de

Radiological significance of thorium processing in manufacturing

International Nuclear Information System (INIS)

Davis, M.W.

1985-01-01

The study of thorium processing in manufacturing comprised monitoring programs at a plant where thorium dioxide was in use and another where the use of thorium nitrate had been discontinued. The measurements of the solubility in simulated lung fluid proved that both materials belonged in the Y Class with dissolution half-times greater than 500 days. Bioassay measurements of 20 subjects from both facilities proved that in vitro monitoring methods, urine, feces, hair and nails analysis were not sufficient indicators of thorium uptake. In vivo monitoring by phoswich and large sodium iodide detectors were proven to be good methods of determining thorium lung burdens. The thoron in breath technique was shown to have a lower limit of sensitivity than lung counting, however, due to lack of information regarding the thoron escape rate from the thorium particles in the lungs the method is not as accurate as lung counting. Two subjects at the thorium dioxide facility had lung burdens of 21+- 16 Bq and 29+- 24 Bq Th 232 and one at the thorium nitrate facility had a lung burden of 37+- 13 Bq. Improvements in the procedures and use of a glove box were among the recommendations to reduce the inhalation of thorium by workers at the thorium dioxide facility. Decontamination of several rooms at the thorium nitrate facility and sealing of the walls and floors were recommended in order to reduce the escape of thoron gas into the room air. The risk to non Atomic Radiation Workers was primarily due to thoron daughters in air while gamma radiation and thorium in air were less important. Conversely, at the thorium dioxide facility the inhalation of thorium in air was the most significant exposure pathway

Design features of the Light Water Breeder Reactor (LWBR) which improve fuel utilization in light water reactors (LWBR development program)

International Nuclear Information System (INIS)

Hecker, H.C.; Freeman, L.B.

1981-08-01

This report surveys reactor core design features of the Light Water Breeder Reactor which make possible improved fuel utilization in light water reactor systems and breeding with the uranium-thorium fuel cycle. The impact of developing the uranium-thorium fuel cycle on utilization of nuclear fuel resources is discussed. The specific core design features related to improved fuel utilization and breeding which have been implemented in the Shippingport LWBR core are presented. These design features include a seed-blanket module with movable fuel for reactivity control, radial and axial reflcetor regions, low hafnium Zircaloy for fuel element cladding and structurals, and a closely spaced fuel rod lattice. Also included is a discussion of several design modifications which could further improve fuel utilization in future light water reactor systems. These include further development of movable fuel control, use of Zircaloy fuel rod support grids, and fuel element design modifications

The economics of thorium fuel cycles

International Nuclear Information System (INIS)

James, R.A.

1978-01-01

The individual cost components and the total fuel cycle costs for natural uranium and thorium fuel cycles are discussed. The thorium cycles are initiated by using either enriched uranium or plutonium. Subsequent thorium cycles utilize recycled uranium-233 and, where necessary, either uranium-235 or plutonium as topping. A calculation is performed to establish the economic conditions under which thorium cycles are economically attractive. (auth)

Vortex Diode Analysis and Testing for Fluoride Salt-Cooled High-Temperature Reactors

International Nuclear Information System (INIS)

Yoder, Graydon L. Jr.; Elkassabgi, Yousri M.; De Leon, Gerardo I.; Fetterly, Caitlin N.; Ramos, Jorge A.; Cunningham, Richard Burns

2012-01-01

Fluidic diodes are presently being considered for use in several fluoride salt-cooled high-temperature reactor designs. A fluidic diode is a passive device that acts as a leaky check valve. These devices are installed in emergency heat removal systems that are designed to passively remove reactor decay heat using natural circulation. The direct reactor auxiliary cooling system (DRACS) uses DRACS salt-to-salt heat exchangers (DHXs) that operate in a path parallel to the core flow. Because of this geometry, under normal operating conditions some flow bypasses the core and flows through the DHX. A flow diode, operating in reverse direction, is-used to minimize this flow when the primary coolant pumps are in operation, while allowing forward flow through the DHX under natural circulation conditions. The DRACSs reject the core decay heat to the environment under loss-of-flow accident conditions and as such are a reactor safety feature. Fluidic diodes have not previously been used in an operating reactor system, and therefore their characteristics must be quantified to ensure successful operation. This report parametrically examines multiple design parameters of a vortex-type fluidic diode to determine the size of diode needed to reject a particular amount of decay heat. Additional calculations were performed to size a scaled diode that could be tested in the Oak Ridge National Laboratory Liquid Salt Flow Loop. These parametric studies have shown that a 152.4 mm diode could be used as a test article in that facility. A design for this diode is developed, and changes to the loop that will be necessary to test the diode are discussed. Initial testing of a scaled flow diode has been carried out in a water loop. The 150 mm diode design discussed above was modified to improve performance, and the final design tested was a 171.45 mm diameter vortex diode. The results of this testing indicate that diodicities of about 20 can be obtained for diodes of this size. Experimental

Evaluation of thorium based nuclear fuel. Actinide waste

International Nuclear Information System (INIS)

Wichers, V.A.

1995-06-01

Use of thorium based fuel has recently been proposed as a possible way to reduce the amount of actinide waste from nuclear power. To examine this possibility, burnup calculations were done of five once-through Thorium Heavy Water Reactor (THWR) systems, and three THWR systems with uranium recycle. The natural uranium once-through system was adopted as reference. The studied THWR fuel systems differed in the choice of fissile makeup fuel and exit burnup. The HWR was chosen because of its good neutron economy. Actinide waste production (in mass per GW e a) and radiotoxicity (in ALI per GW e a) for storage times up to 10 6 a were calculated for each system. The study shows that the THWR system with uranium recycle and High Enriched Uranium (U-235) makeup fuel performed best, producing both the lowest amount of plutonium and actinide waste with the lowest radiotoxicity. Relative to the natural uranium in HWR once-through system, radiotoxicity is reduced by a factor varying between 2 and 50 for the full range of storage times up to 10 6 a. (orig.)

Accelerator molten-salt breeding and thorium fuel cycle

International Nuclear Information System (INIS)

Furukawa, Kazuo; Nakahara, Yasuaki; Kato, Yoshio; Ohno, Hideo; Mitachi, Kohshi.

1990-01-01

The recent efforts at the development of fission energy utilization have not been successful in establishing fully rational technology. A new philosophy should be established on the basis of the following three principles: (1) thorium utilization, (2) molten-salt fuel concept, and (3) separation of fissile-breeding and power-generating functions. Such philosophy is called 'Thorium Molten-Salt Nuclear Energy Synergetics [THORIMS-NES]'. The present report first addresses the establishment of 233 U breeding fuel cycle, focusing on major features of the Breeding and Chemical Processing Centers and a small molten-salt power station (called FUJI-II). The development of fissile producing breeders is discussed in relation to accelerator molten-salt breeder (AMSB), impact fusion molten-salt breeder, and inertial-confined fusion hybrid molten-salt breeder. Features of the accelerator molten-salt breeder are described, focusing on technical problems with accelerator breeders (or spallators), design principle of the accelerator molten-salt breeder, selection of molten salt compositions, and nuclear- and reactor-chemical aspects of AMSB. Discussion is also made of further research and development efforts required in the future for AMSB. (N.K.)

Synthetic Strategies for the Synthesis of Ternary Uranium(IV) and Thorium(IV) Fluorides.

Science.gov (United States)

Klepov, Vladislav V; Felder, Justin B; Zur Loye, Hans-Conrad

2018-04-10

A series of new U(IV) and Th(IV) fluorides, Na 7 U 6 F 31 (1), NaUF 5 (2), NaU 2 F 9 (3), KTh 2 F 9 (4), NaTh 2 F 9 (5), (H 3 O)Th 3 F 13 (6), and (H 3 O)U 3 F 13 (7), was obtained using hydrothermal and low-temperature flux methods. Mild hydrothermal reactions with uranyl acetate as a precursor yielded 1, 7, and the monoclinic polymorph of NaU 2 F 9 , whereas direct reactions between UF 4 and NaF led to the formation of 2 and orthorhombic NaU 2 F 9 (3). This highlights an unexpected difference in reaction products when different starting uranium sources are used. All seven compounds were characterized by single-crystal X-ray diffraction, and their structures are compared on the basis of cation topology, revealing a close topological resemblance between fluorides on the basis of the layers observed in NaUF 5 (H 2 O). Phase-pure samples of 1, 2, and both polymorphs of NaU 2 F 9 were obtained, and their spectroscopic and magnetic properties were measured. The UV-vis data are dominated by the presence of U 4+ cations and agree well with the electronic transitions. Effective magnetic moments of the studied compounds were found to range from 3.08 to 3.59 μ B .

Advanced In-Core Fuel Cycles for the Gas Turbine-Modular Helium Reactor

Energy Technology Data Exchange (ETDEWEB)

Talamo, Alberto

2006-04-15

Amid generation IV of nuclear power plants, the Gas Turbine - Modular Helium Reactor, designed by General Atomics, is the only core with an energy conversion efficiency of 50%; the safety aspects, coupled to construction and operation costs lower than ordinary Light Water Reactors, renders the Gas Turbine - Modular Helium reactor rather unequaled. In the present studies we investigated the possibility to operate the GT-MHR with two types of fuels: LWRs waste and thorium; since thorium is made of only fertile {sup 232}Th, we tried to mix it with pure {sup 233}U, {sup 235}U or {sup 239}Pu; ex post facto, only uranium isotopes allow the reactor operation, that induced us to examine the possibility to use a mixture of uranium, enriched 20% in {sup 235}U, and thorium. We performed all calculations by the MCNP and MCB codes, which allowed to model the reactor in a very detailed three-dimensional geometry and to describe the nuclides transmutation in a continuous energy approach; finally, we completed our studies by verifying the influence of the major nuclear data libraries, JEFF, JENDL and ENDF/B, on the obtained results.

Radiogenic lead from poly-metallic thorium ores as a valuable material for advanced nuclear facilities

Energy Technology Data Exchange (ETDEWEB)

Kulikov, Gennady G.; Apse, Vladimir A.; Kulikov, Evgeny G.; Kozhahmet, Bauyrzhan K.; Shkodin, Alexey O.; Shmelev, Anatoly N.

2017-03-15

Main purpose of the study is assessing reasonability for recovery, production and application of radiogenic lead as a coolant, neutron moderator and neutron reflector in advanced fast reactors and accelerator-driven systems (ADS). The following results were obtained: 1. Radiogenic lead with high content of isotope {sup 208}Pb can be extracted from thorium or mixed thorium-uranium ores because {sup 208}Pb is a final product of {sup 232}Th natural decay chain. 2. The use of radiogenic lead with high {sup 208}Pb content in advanced fast reactors and ADS makes it possible to improve significantly their neutron-physical and thermal-hydraulic parameters. 3. The use of radiogenic lead with high {sup 208}Pb content in advanced fast reactors as a coolant opens the possibilities for more intense fuel breeding and for application of well-known oxide fuel instead of the promising but not tested enough nitride fuel under the same safety parameters. 4. The use of radiogenic lead with high {sup 208}Pb content in advanced fast reactors as a neutron reflector opens a possibility for substantial elongation of prompt neutron lifetime. As a result, chain fission reaction in the reactor core could be slowed down, and the reactor operation could become safer. 5. The use of radiogenic lead with high {sup 208}Pb content in ADS as a coolant can upgrade substantially the level of neutron flux in the ADS blanket. Thus, favorable conditions could be formed in the ADS blanket for effective transmutation of radioactive wastes with low cross-sections of radiative neutron capture.

Investigation of thorium hydroxotrifluoroacetates

International Nuclear Information System (INIS)

Andryushin, V.G.; Samatov, A.V.; Chuklinov, R.N.; Shmidt, V.S.

1984-01-01

The precipitation process of thorium hydroxotrifluoroacetates in the Th(NO 3 ) 4 -HNO 3 -CF 3 COOH-NH 4 OH-H 2 O system in the pH range from 0.1 to 8.6 at a 100 g/l thorium concentration in it has been investigated. The curve of the pH dependence of the main thorium salts solubility in the pH=4.4 range exhibits a local maximum, the position of the latter being in complete accordance with its earlier established relation to the parameter of the ligand anion nucleophility. The composition of isolated hydroxotrifluoroacetate hydrates corresponds to the generic formula Th(OH)sub(x)(CFsub(3)COO)sub(4-x)xnHsub(2)O, where 3.0 >= x >= 1.5, and n=1.0-6.0. The density of the crystals obtained is measured and the thermal stability is studied. It is established, that, for the thorium hydroxotrifluoroacetate hydrates, the same general regularities in the effect of degree of hydrolysis and hydration on the position of decomposition temperature effects and on the density of compounds hold, as has been previously found in studying thorium- and plutonium hydroxosalts

Analytical calculation of the fuel temperature reactivity coefficient for pebble bed and prismatic high temperature reactors for plutonium and uranium-thorium fuels

International Nuclear Information System (INIS)

Talamo, Alberto

2007-01-01

We analytically evaluated the fuel coefficient of temperature both for pebble bed and prismatic high temperature reactors when they utilize as fuel plutonium and minor actinides from light water reactors spent fuel or a mixture of 50% uranium, enriched 20% in 235 U, and 50% thorium. In both cores the calculation involves the evaluation of the resonances integrals of the high absorbers fuel nuclides 240 Pu, 238 U and 232 Th and it requires the esteem of the Dancoff-Ginsburg factor for a pebble bed or prismatic core. The Dancoff-Ginsburg factor represents the only discriminating parameter in the results for the two different reactors types; in fact, both the pebble bed and the prismatic reactors share the same the pseudo-cross-section describing an infinite medium made of graphite filled by TRISO particles. We considered only the resolved resonances with a statistical spin factor equal to one and we took into account 267, 72, 212 resonances in the range 1.057-5692, 6.674-14485, 21.78-3472 eV for 240 Pu, 238 U and 232 Th, respectively, for investigating the influence on the fuel temperature reactivity coefficient of the variation of the TRISO kernel radius and TRISO particles packing fraction from 100, 200 to 300 μm and from 10% to 50%, respectively. Finally, in the pebble bed core, we varied the radius of the pebble for setting a fuel temperature reactivity coefficient similar to the one of a prismatic core