WorldWideScience

Sample records for fluid sealing technology

  1. Fluid seals technology at BHR Group Ltd.

    Science.gov (United States)

    Leefe, Simon

    1991-01-01

    A mathematical model was developed for ESA, which couples the rigid body dynamics in four degrees of freedom of a flexibly mounted stator (with Coulomb damping) of a turbopump face seal with the fluid film behavior. The interfacial film is assumed gaseous, and the model incorporates laminar/turbulent flow, inertia and sonic choking. Seal faces may be wavy and coned, while the rotating ring can be eccentrically mounted, misaligned with the shaft and oscillate axially at arbitrary frequency. The model is currently being coded into software. An experimental program using a high speed cryogenic/hot gas test rig is being conducted to verify the output of the computer program.

  2. NEW POLIMER SEALING FLUID STOPS MUD LOSS

    Directory of Open Access Journals (Sweden)

    Stanislaw Stryczek

    1989-12-01

    Full Text Available This paper deals with a composition of sealing fluid, prepared from acrylic acid salt water solution Solakryl M. Laboratory test results of technological properties of its modifications with mineral agents are shown. A new method of sealing mud loss operations with given sealing liquid is discussed along with comments on effects of its use for stopping mud loss in case of freeze-well drilling is described (the paper is published in Croatian.

  3. Numerical Analysis of Magnetic Fluid Sealing Performance

    Institute of Scientific and Technical Information of China (English)

    2006-01-01

    The sealing performance of magnetic fluid is related to the magnetic fluid itself. Many factors can influence the magnetic field and the seal pressure differences of magnetic fluid seals, such as the sealing gap, the shaft eccentricity, the shaft diameter, the volume of the magnetic fluid and the centrifugal force. These factors are analyzed by numerical computation . When the seal material and structure are the same, the seal pressure difference is directly proportional to the magnetic field intensity and the saturation magnetization of the magnetic fluid. The sealing performance of the magnetic fluid will reduce with the increase of the sealing gap and shaft eccentricity. The sealing performance will increase with the volume of the magnetic fluid and decrease with the increase of the shaft diameter taking gravity into account. The increase of the shaft diameter is the same as the reduction of the volume of the magnetic fluid. The magnetic fluid cross-section can change because of the centrifugal force. Some improvements can reduce the influence of the centrifugal force. The centrifugal force can be utilized to improve the sealing performance.

  4. TECHNOLOGY ROADMAPPING FOR IAEA SEALS.

    Energy Technology Data Exchange (ETDEWEB)

    HOFFHEINS,B.; ANNESE,C.; GOODMAN,M.; OCONNOR,W.; GUSHUE,S.; PEPPER,S.

    2003-07-13

    In the fall of 2002, the U.S. Support Program (USSP) initiated an effort to define a strategy or ''roadmap'' for future seals technologies and to develop a generalized process for planning safeguards equipment development, which includes seals and other safeguards equipment. The underlying objectives of the USSP include becoming more proactive than reactive in addressing safeguards equipment needs, helping the IAEA to maintain an inventory of cost-effective, reliable, and effective safeguards equipment, establishing a long-term planning horizon, and securing IAEA ownership in the process of effective requirements definition and timely transitioning of new or improved systems for IAEA use. At an initial workshop, seals, their functions, performance issues, and future embodiments were discussed in the following order: adhesive seals, metal seals, passive and active loop seals, ultrasonic seals, tamper indicating enclosures (including sample containers, equipment enclosures, and conduits). Suggested improvements to these technologies focused largely on a few themes: (1) The seals must be applied quickly, easily, and correctly; (2) Seals and their associated equipment should not unduly add bulk or weight to the inspectors load; (3) Rapid, in-situ verifiability of seals is desirable; and (4) Seal systems for high risk or high value applications should have two-way, remote communications. Based upon these observations and other insights, the participants constructed a skeletal approach for seals technology planning. The process begins with a top-level review of the fundamental safeguards requirements and extraction of required system features, which is followed by analysis of suitable technologies and identification of technology gaps, and finally by development of a planning schedule for system improvements and new technology integration. Development of a comprehensive procedure will require the partnership and participation of the IAEA. The

  5. Characteristics of a magnetic fluid seal and its motion in an axial variable seal gap

    Institute of Scientific and Technical Information of China (English)

    QIAN Ji-guo; YANG Zhi-yi

    2008-01-01

    With suitable assumptions a hydrodynamic model for the magnetic fluid motion in an axial variable gap seal was constructed, and the solution to the equations of the model was deduced. The characteristics of a magnetic fluid seal and its motion,including the speed and pressure distribution, and the seal capacity of a magnetic fluid rotating seal were systematically described.The factors affecting seal capacity and ways to improve seal capacity based on the hydrodynamic model are discussed. The basic condition for dynamic seal availability is presented. The rotating speed and radius of the shafts should be decreased. The work can provide proof of a seal design or suggest ways to improve the seal capacity of magnetic fluid seals.

  6. Application study of magnetic fluid seal in hydraulic turbine

    Science.gov (United States)

    Yu, Z. Y.; Zhang, W.

    2012-11-01

    The waterpower resources of our country are abundant, and the hydroelectric power is developed, but at present the main shaft sealing device of hydraulic turbine is easy to wear and tear and the leakage is great. The magnetic fluid seal has the advantages of no contact, no wear, self-healing, long life and so on. In this paper, the magnetic fluid seal would be used in the main shaft of hydraulic turbine, the sealing structure was built the model, meshed the geometry, applied loads and solved by using MULTIPHYSICS in ANSYS software, the influence of the various sealing structural parameters such as tooth width, height, slot width, sealing gap on the sealing property were analyzed, the magnetic fluid sealing device suitable for large-diameter shaft and sealing water was designed, the sealing problem of the hydraulic turbine main shaft was solved effectively which will bring huge economic benefits.

  7. Design optimization of seal structure for sealing liquid by magnetic fluids

    Science.gov (United States)

    Liu, Tonggang; Cheng, Yusheng; Yang, Zhiyi

    2005-03-01

    The durability of the magnetic fluid seal clearly decreases when sealing another liquid because of the interface instability caused by the applied magnetic field and the velocity difference of the two liquids. With an intention to establish a stable interface during sealing liquid, a new magnetic fluid seal was developed in this paper. The parameters of the structure were optimized by a simulation apparatus. And the magnetic fluid seal designed based on the optimum parameters shows good performance and long life for sealing lubricating oil.

  8. Seal Technology in Gas Turbine Engines

    Science.gov (United States)

    1978-08-01

    high speeds; b) the pressure, temperature and flow rate of the sealing and coolant fluid should be in dependently varied; c) various sealing media ...been determined from the geometricA Input data. Tne thermal moments are evaluated by regarding thermal stresses as equivalent to distributed body

  9. Seals/Secondary Fluid Flows Workshop 1997; Volume I

    Science.gov (United States)

    Hendricks, Robert C. (Editor)

    2006-01-01

    The 1997 Conference provided discussions and data on (a) program overviews, (b) developments in seals and secondary air management systems, (c) interactive seals flows with secondary air or fluid flows and powerstream flows, (d) views of engine externals and limitations, (e) high speed engine research sealing needs and demands, and (f) a short course on engine design development margins. Sealing concepts discussed include, mechanical rim and cavity seals, leaf, finger, air/oil, rope, floating-brush, floating-T-buffer, and brush seals. Engine externals include all components of engine fluid systems, sensors and their support structures that lie within or project through the nacelle. The clean features of the nacelle belie the minefield of challenges and opportunities that lie within. Seals; Secondary air flows; Rotordynamics; Gas turbine; Aircraft; CFD; Testing; Turbomachinery

  10. Gas-path seal technology

    Science.gov (United States)

    Zuk, J.

    1976-01-01

    Improved gas-path seals are needed for better fuel economy, longer performance retention, and lower maintenance, particularly in advanced, high-performance gas turbine engines. Problems encountered in gas-path sealing are described, as well as new blade-tip sealing approaches for high-pressure compressors and turbines. These include a lubricant coating for conventional, porous-metal, rub-strip materials used in compressors. An improved hot-press metal alloy shows promise to increase the operating surface temperatures of high-pressure-turbine, blade-tip seals to 1450 K (2150 F). Three ceramic seal materials are also described that have the potential to allow much higher gas-path surface operating temperatures than are possible with metal systems.

  11. Failure of Magnetic Fluid Seals Operating in Water: Preliminary Conclusions

    Directory of Open Access Journals (Sweden)

    Matuszewski Leszek

    2017-06-01

    Full Text Available The article analyses properties of magnetic fluid seals installed in rotary sealing nodes which operate in the utility water environment. Seals of this type have been examined as a possible solution to the problem with ship manoeuvring propulsion sealing. The present analysis bases on laboratory durability tests of magnetic fluid seals exposed to longterm utility water loads, at different water pressures and shaft revolutions. The basic seal durability criterion was the number of revolutions made by the sealing node shaft until the appearance of water tightness loss (leakage. It was found that the main factor leading to the wear of the seal is the relative speed of the magnetic fluid with respect to that of the utility water, and this process is heavily affected by the pressure acting on the seal. The reported test results are presented in the form of diagrams showing the seal durability (time until water tightness loss as a function of rotational speed. The curves shown in the diagrams are regular, with two different rotational speed ranges: the highspeed range, when the tightness loss is relatively fast, and the low-speed range, with a clear tendency to prolong the seal lifetime. These diagrams were given the name of durability curves of the MF seal operating in water. The results of the performed tests suggest formal similarity between the experimental data distribution concerning tightness loss processes occurring in magnetic fluid seals operating in water environment and metal fatigue processes. The article proposes a preliminary simplified durability model to describe the examined phenomenon.

  12. A New Design of Magnetic Fluid Seal for Liquids

    Institute of Scientific and Technical Information of China (English)

    LIU Tong-gang; YANG Zhi-yi

    2005-01-01

    Direct contract between the sealed liquid and the magnetic fluid in a dynamic system under magnetic field may lead to an unstable interface, consequently, break down the seal. Aiming at this problem, a new magnetic fluid seal (MFS) was developed. In this new MFS, a soft iron bushing with high permeability was introduced on the shaft and nonferrous shields were installed beside the bushing and the pole pieces. The parameters of the bushing and the shields were optimized in a seal simulation facility. The results show that the bushing with a thickness of 7 mm and shields with a width of 8 mm are best for sealing a shaft 20 mm in diameter. The MFS designed based on the optimum parameters shows good performance and long life span for sealing lubricating oil.

  13. Influence of Rocket Engine Characteristics on Shaft Sealing Technology Needs

    Science.gov (United States)

    Keba, John E.

    1999-01-01

    This paper presents viewgraphs of The Influence of Rocket Engine Characteristics on Shaft Sealing Technology Needs. The topics include: 1) Rocket Turbomachinery Shaft Seals (Inter-Propellant-Seal (IPS) Systems, Lift-off Seal Systems, and Technology Development Needs); 2) Rocket Engine Characteristics (Engine cycles, propellants, missions, etc., Influence on shaft sealing requirements); and 3) Conclusions.

  14. Thermal Fluid-Solid Interaction Model and Experimental Validation for Hydrostatic Mechanical Face Seals

    Institute of Scientific and Technical Information of China (English)

    HUANG Weifeng; LIAO Chuanjun; LIU Xiangfeng; SUO Shuangfu; LIU Ying; WANG Yuming

    2014-01-01

    Hydrostatic mechanical face seals for reactor coolant pumps are very important for the safety and reliability of pressurized-water reactor power plants. More accurate models on the operating mechanism of the seals are needed to help improve their performance. The thermal fluid-solid interaction (TFSI) mechanism of the hydrostatic seal is investigated in this study. Numerical models of the flow field and seal assembly are developed. Based on the mechanism for the continuity condition of the physical quantities at the fluid-solid interface, an on-line numerical TFSI model for the hydrostatic mechanical seal is proposed using an iterative coupling method. Dynamic mesh technology is adopted to adapt to the changing boundary shape. Experiments were performed on a test rig using a full-size test seal to obtain the leakage rate as a function of the differential pressure. The effectiveness and accuracy of the TFSI model were verified by comparing the simulation results and experimental data. Using the TFSI model, the behavior of the seal is presented, including mechanical and thermal deformation, and the temperature field. The influences of the rotating speed and differential pressure of the sealing device on the temperature field, which occur widely in the actual use of the seal, are studied. This research proposes an on-line and assembly-based TFSI model for hydrostatic mechanical face seals, and the model is validated by full-sized experiments.

  15. Application of hydrophilic magnetic fluid to oil seal

    Science.gov (United States)

    Kim, Y. S.; Nakatsuka, K.; Fujita, T.; Atarashi, T.

    1999-07-01

    Bearing and gear are important components in machines. Lubricant for bearing or gear is usually confined in working space by rubber retainer or mechanical seal, and its lifetime which is determined by the friction wear of sealing material is important. In this report, the basic characteristics of magnetic fluid seal applied to lubricant retainer is studied. The fluid used for this purpose is ethyleneglycol-based magnetic fluid in which silica-coated iron particles are dispersed. The lubricant oil seal set consisting of six stages of pole piece and Nd-permanent magnets (4.0 Wb/m 2) in seal housing showed an excellent pressure resistance of 618 kPa under a rotating speed of 1800 rpm.

  16. A 3D-CFD code for accurate prediction of fluid flows and fluid forces in seals

    Science.gov (United States)

    Athavale, M. M.; Przekwas, A. J.; Hendricks, R. C.

    1994-01-01

    Current and future turbomachinery requires advanced seal configurations to control leakage, inhibit mixing of incompatible fluids and to control the rotodynamic response. In recognition of a deficiency in the existing predictive methodology for seals, a seven year effort was established in 1990 by NASA's Office of Aeronautics Exploration and Technology, under the Earth-to-Orbit Propulsion program, to develop validated Computational Fluid Dynamics (CFD) concepts, codes and analyses for seals. The effort will provide NASA and the U.S. Aerospace Industry with advanced CFD scientific codes and industrial codes for analyzing and designing turbomachinery seals. An advanced 3D CFD cylindrical seal code has been developed, incorporating state-of-the-art computational methodology for flow analysis in straight, tapered and stepped seals. Relevant computational features of the code include: stationary/rotating coordinates, cylindrical and general Body Fitted Coordinates (BFC) systems, high order differencing schemes, colocated variable arrangement, advanced turbulence models, incompressible/compressible flows, and moving grids. This paper presents the current status of code development, code demonstration for predicting rotordynamic coefficients, numerical parametric study of entrance loss coefficients for generic annular seals, and plans for code extensions to labyrinth, damping, and other seal configurations.

  17. Seal assembly with anti-rotation pin for high pressure supercritical fluids

    Science.gov (United States)

    Wright, Steven A.; Fuller, Robert L.

    2014-08-05

    A seal assembly for sealing a machine with a first chamber and a second chamber is provided. A rotating shaft extends through the first and second chambers, and rotates therein. The seal assembly has a seal housing, a seal ring and a seal pin. The seal housing is positionable in the machine housing. The seal housing has a seal pocket extending into a fluid side thereof, and a housing receptacle extending into an inner diameter thereof at the seal pocket. The seal ring is positionable in the seal pocket of the seal housing for forming a seal therewith. The seal ring has a ring receptacle extending into an outer diameter thereof. The ring receptacle is positionable adjacent to the housing receptacle for defining a pin hole therebetween. The seal pin is loosely positionable in the pin hole whereby movement about the seal ring is accommodated while preventing rotation thereof.

  18. Investigation of seal technology for Francis turbine

    Energy Technology Data Exchange (ETDEWEB)

    Zhao, Wei

    2012-06-01

    Leakage loss and disk friction loss caused by the clearance gap flow at the back of a runner have a major impact on the efficiency of hydraulic turbines. Accordingly, it is extremely important to develop and improve the seal technology by investigating the gap flow. Generally, there are two types of the gap flow: axial gap flow between a rotating disk and a stator (e.g. the flow at the back of a runner) and the annular gap flow (e.g. the flow at an annular seal). Firstly, the overview of previous researches on labyrinth seal, rotating disk flow and Taylor-Couette flow are summarized. Labyrinth seals are the primary type of seals for turbo machinery. However, most researchers studied it for compressible flow only. It is also found that the enclosed rotating disk flow with through-flow can be studied instead of the gap flow in a hydraulic machine. Furthermore, the above mentioned annular gap flow is similar to the Taylor-Couette flow. The Taylor-vortices are formed in the annular gap due to the rotation of disk, which could be used as a resistance of flow. Therefore, in the present work, three parts are investigated. The first part is the investigation of the labyrinth seal for Francis turbines. The second part is the investigation of the gap flow between two stationary walls. The third part is investigation of the annular gap flow between one stationary and one rotating wall, based on the theory of Taylor-Couette flow. Afterwards, the theoretical formulas for leakage flow of a traditional labyrinth seal used in high head Francis turbine is derived and is verified to give acceptable results. The theoretical model is useful to predict the leakage flow by the measurements of Francis turbine at the Aabjoera Power plant. For straight-through labyrinth seal, the effects of cavity dimensions, numbers and locations on the leakage flow are investigated numerically. Smaller cavity depth, longer cavity length and fewer cavity numbers are required in order to reduce leakage

  19. CHARACTERISTCS OF FLUID FILM IN OPTIMIZED SPIRAL GROOVE MECHANICAL SEAL

    Institute of Scientific and Technical Information of China (English)

    2007-01-01

    In order to investigate the sealing performance variation resulted from the thermal deformation of the end faces, the equations to calculate the fluid film pressure distribution, the bearing force and the leakage rate are derived, for the fluid film both in parallel gap and in wedgy gap. The geometrical parameters of the sealing members are optimized by means of heat transfer analysis and complex method. The analysis results indicate that the shallow spiral grooves can generate hydrodynamic pressure while the rotating ring rotates and the bearing force of the fluid film in spiral groove end faces is much larger than that in the flat end faces. The deformation increases the bearing force of the fluid film in flat end faces, but it decreases the hydrodynamic pressure of the fluid film in spiral groove end faces. The gap dimensions which determine the characteristics of the fluid film is obtained by coupling analysis of the frictional heat and the thermal deformation in consideration of the equilibrium condition of the bearing force and the closing force. For different gap dimensions, the relationship between the closing force and the leakage rate is also investigated, based on which the leakage rate can be controlled by adjusting the closing force.

  20. Field Trial of an Aerosol-Based Enclosure Sealing Technology

    Energy Technology Data Exchange (ETDEWEB)

    Harrington, Curtis [Univ. of California, Davis, CA (United States); Springer, David [Alliance for Residential Building Innovation (ARBI), Davis, CA (United States)

    2015-09-01

    This report presents the results from several demonstrations of a new method for sealing building envelope air leaks using an aerosol sealing process developed by the Western Cooling Efficiency Center at UC Davis. The process involves pressurizing a building while applying an aerosol sealant to the interior. As air escapes through leaks in the building envelope, the aerosol particles are transported to the leaks where they collect and form a seal that blocks the leak. Standard blower door technology is used to facilitate the building pressurization, which allows the installer to track the sealing progress during the installation and automatically verify the final building tightness. Each aerosol envelope sealing installation was performed after drywall was installed and taped, and the process did not appear to interrupt the construction schedule or interfere with other trades working in the homes. The labor needed to physically seal bulk air leaks in typical construction will not be replaced by this technology.

  1. Field Trial of an Aerosol-Based Enclosure Sealing Technology

    Energy Technology Data Exchange (ETDEWEB)

    Harrington, Curtis [Univ. of California, Davis, CA (United States); Springer, David [Univ. of California, Davis, CA (United States)

    2015-09-01

    This report presents the results from several demonstrations of a new method for sealing building envelope air leaks using an aerosol sealing process developed by the Western Cooling Efficiency Center at UC Davis. The process involves pressurizing a building while applying an aerosol sealant to the interior. As air escapes through leaks in the building envelope, the aerosol particles are transported to the leaks where they collect and form a seal that blocks the leak. Standard blower door technology is used to facilitate the building pressurization, which allows the installer to track the sealing progress during the installation and automatically verify the final building tightness. Each aerosol envelope sealing installation was performed after drywall was installed and taped, and the process did not appear to interrupt the construction schedule or interfere with other trades working in the homes. The labor needed to physically seal bulk air leaks in typical construction will not be replaced by this technology. However, this technology is capable of bringing the air leakage of a building that was built with standard construction techniques and HERS-verified sealing down to levels that would meet DOE Zero Energy Ready Homes program requirements. When a developer is striving to meet a tighter envelope leakage specification, this technology could greatly reduce the cost to achieve that goal by providing a simple and relatively low cost method for reducing the air leakage of a building envelope with little to no change in their common building practices.

  2. Frictional heat transfer regularity of the fluid film in mechanical seals

    Institute of Scientific and Technical Information of China (English)

    2008-01-01

    The frictional heat transfer regularity in the mechanical seal system consisting of the rotating ring, the stationary ring, the fluid film in the end faces and the sealed medium was investigated. The primary factors affecting the frictional heat transfer regularity, such as the heat transfer coefficients from the rings to the sealed medium, the frictional heat flux, the frictional heat distribution ratio and so on, were discussed. The equations for calculating the temperature field both in the sealing members and in the fluid film were derived. The coupling analysis of the frictional heat of the fluid film and the thermal deformation of the two end faces of the rings was carried out to obtain the separation angle of the two deformed end faces in consideration of the viscosity change of the fluid film. The results indicate that the frictional heat of the fluid film heavily affects its characteristic and the sealing performance of mechanical seals. The frictional heat changes not only the shape of the gap between the end faces but also the viscosity of the fluid film, and thereupon leads to the increase of the leakage rate. The maximum temperature of the system is at the inner radius of the fluid film, and most of the frictional heat is conducted by the rotating ring. Based on the heat transfer analysis method put forward in this paper, the parameterized design of mechanical seals can be realized to determine the best geometrical parameters and to select the appropriate material of the sealing members.

  3. Magnetic fluid based squeeze film between porous circular disks with sealed boundary

    Institute of Scientific and Technical Information of China (English)

    R.M.PATEL; G.M.DEHERI

    2001-01-01

    Efforts have been made to study the effect of the magnetic fluid lubricant and the seal-ing of the boundary for the squeeze film between two circular disks when the upper disk having aporous facing with its boundary sealed, approaches the non-porous lower disk normally. The modi-fied Reynolds equations for the fluid region and the governing Laplacian equation for the pressurein porous region are solved with appropriate boundary conditions. Expressions are obtained forpressure, load carrying capacity and the response time. The results are presented graphically. Thecombined effect of the magnetic fluid lubricant and sealing of the boundary increases the load car-rying capacity significantly and hence the performance of the bearing can be enhanced considera-bly by sealing the boundary and taking a magnetic fluid as lubricant.

  4. Computational fluid mechanics utilizing the variational principle of modeling damping seals

    Science.gov (United States)

    Abernathy, J. M.

    1986-01-01

    A computational fluid dynamics code for application to traditional incompressible flow problems has been developed. The method is actually a slight compressibility approach which takes advantage of the bulk modulus and finite sound speed of all real fluids. The finite element numerical analog uses a dynamic differencing scheme based, in part, on a variational principle for computational fluid dynamics. The code was developed in order to study the feasibility of damping seals for high speed turbomachinery. Preliminary seal analyses have been performed.

  5. Supercritical fluid technology

    Energy Technology Data Exchange (ETDEWEB)

    Penninger, J.M.L.; McHugh, M.A.; Radosz, M.; Krukonis, V.J.

    1985-01-01

    This book presents the state-of-the-art in the science and technology of supercritical fluid (scf) processing. Current research as described in the book, focuses on developments in equations of state for binary and multicomponent mixtures (including polymer solutions), solubility measurements at near-critical conditions, measurements of critical properties of binary mixtures and their correlation with equations of state. Progress in thermodynamics, coupled with advances in the design and construction of high pressure equipment, has opened up a wide avenue of commercial application (e.g. decaffeination of coffee beans, extractions of flavours and spices, purification of pharmaceutical products, separations of polymeric materials, deodorization and deacidification of vegetable oils, fractionation of fatty acids, coal liquefaction, wood delignitication, etc.)

  6. Fluid-solid interaction model for hydraulic reciprocating O-ring seals

    Science.gov (United States)

    Liao, Chuanjun; Huang, Weifeng; Wang, Yuming; Suo, Shuangfu; Liu, Ying

    2013-01-01

    Elastohydrodynamic lubrication characteristics of hydraulic reciprocating seals have significant effects on sealing and tribology performances of hydraulic actuators, especially in high parameter hydraulic systems. Only elastic deformations of hydraulic reciprocating seals were discussed, and hydrodynamic effects were neglected in many studies. The physical process of the fluid-solid interaction effect did not be clearly presented in the existing fluid-solid interaction models for hydraulic reciprocating O-ring seals, and few of these models had been simultaneously validated through experiments. By exploring the physical process of the fluid-solid interaction effect of the hydraulic reciprocating O-ring seal, a numerical fluid-solid interaction model consisting of fluid lubrication, contact mechanics, asperity contact and elastic deformation analyses is constructed with an iterative procedure. With the SRV friction and wear tester, the experiments are performed to investigate the elastohydrodynamic lubrication characteristics of the O-ring seal. The regularity of the friction coefficient varying with the speed of reciprocating motion is obtained in the mixed lubrication condition. The experimental result is used to validate the fluid-solid interaction model. Based on the model, The elastohydrodynamic lubrication characteristics of the hydraulic reciprocating O-ring seal are presented respectively in the dry friction, mixed lubrication and full film lubrication conditions, including of the contact pressure, film thickness, friction coefficient, liquid film pressure and viscous shear stress in the sealing zone. The proposed numerical fluid-solid interaction model can be effectively used to analyze the operation characteristics of the hydraulic reciprocating O-ring seal, and can also be widely used to study other hydraulic reciprocating seals.

  7. Handbook of hydraulic fluid technology

    CERN Document Server

    Totten, George E

    2011-01-01

    ""The Handbook of Hydraulic Fluid Technology"" serves as the foremost resource for designing hydraulic systems and for selecting hydraulic fluids used in engineering applications. Featuring new illustrations, data tables, as well as practical examples, this second edition is updated with essential information on the latest hydraulic fluids and testing methods. The detailed text facilitates unparalleled understanding of the total hydraulic system, including important hardware, fluid properties, and hydraulic lubricants. Written by worldwide experts, the book also offers a rigorous overview of h

  8. Field Test and Evaluation of Engineered Biomineralization Technology for Sealing Existing Wells

    Energy Technology Data Exchange (ETDEWEB)

    Cunningham, Alfred [Montana State Univ., Bozeman, MT (United States)

    2015-12-21

    This research project addresses one of the goals of the U.S. Department of Energy (DOE) Carbon Storage Program (CSP) aimed at developing Advanced Wellbore Integrity Technologies to Ensure Permanent Geologic Carbon Storage. The technology field-tested in this research project is referred to as microbially induced calcite precipitation (MICP), which utilizes a biologically-based process to precipitate calcium carbonate. If properly controlled MICP can successfully seal fractures, high permeability zones, and compromised wellbore cement in the vicinity of wellbores and in nearby caprock, thereby improving the storage security of geologically-stored carbon dioxide. This report describes an MICP sealing field test performed on a 24.4 cm (9.625 inch) diameter well located on the Gorgas Steam Generation facility near Jasper, Alabama. The research was aimed at (1) developing methods for delivering MICP promoting fluids downhole using conventional oil field technologies and (2) assessing the ability of MICP to seal cement and formation fractures in the near wellbore region in a sandstone formation. Both objectives were accomplished successfully during a field test performed during the period April 1-11, 2014. The test resulted in complete biomineralization sealing of a horizontal fracture located 340.7 m (1118 feet) below ground surface. A total of 24 calcium injections and six microbial inoculation injections were required over a three day period in order to achieve complete sealing. The fractured region was considered completely sealed when it was no longer possible to inject fluids into the formation without exceeding the initial formation fracture pressure. The test was accomplished using conventional oil field technology including an 11.4 L (3.0 gallon) wireline dump bailer for injecting the biomineralization materials downhole. Metrics indicating successful MICP sealing included reduced injectivity during seal formation, reduction in pressure falloff, and

  9. ENVIRONMENTAL TECHNOLOGY VERIFICATION REPORT-A AND A ENVIRONMENTAL SEALS, INC., SEAL ASSIST SYSTEM (SAS) PHASE II REPORT

    Science.gov (United States)

    The Environmental Technology Verification report discusses the technology and performance of Seal Assist System (SAS) for natural gas reciprocating compressor rod packing manufactured by A&A Environmental Seals, Inc. The SAS uses a secondary containment gland to collect natural g...

  10. SERS-active nanoparticle aggregate technology for tags and seals

    Energy Technology Data Exchange (ETDEWEB)

    Brown, Leif O [Los Alamos National Laboratory; Montoya, Velma M [Los Alamos National Laboratory; Havrilla, George J [Los Alamos National Laboratory; Doorn, Stephen K [Los Alamos National Laboratory

    2010-06-03

    In this paper, we describe our efforts to create a modern tagging and sealing technology for international safeguards application. Our passive tagging methods are based on SANAs (SERS-Active Nanoparticle Aggregates; SERS: Surface Enhanced Raman Scattering). These SANAs offer robust spectral barcoding capability in an inexpensive tag/seal, with the possibility of rapid in-field verification that requires no human input. At INMM 2009, we introduced SANAs, and showed approaches to integrating our technology with tags under development at Sandia National Laboratories (SNL). Here, we will focus on recent LANL development work, as well as adding additional dimensionality to the barcoding technique. The field of international safeguards employs a broad array of tags, seals, and tamper-indicating devices to assist with identification, tracking, and verification of components and materials. These devices each have unique strengths suited to specific applications, and span a range of technologies from passive metal cup seals and adhesive seals to active, remotely monitored fiber optic seals. Regardless of the technology employed, essential characteristics center around security, environmental and temporal stability, ease of use, and the ability to provide confidence to all parties. Here, we present a new inexpensive tagging technology that will deliver these attributes, while forming the basis of either a new seal, or as a secure layer added to many existing devices. Our approach uses the Surface Enhanced Raman Scattering (SERS) response from SANAs (SERS-Active Nanoparticle Aggregates, Figure 1) to provide a unique identifier or signature for tagging applications. SANAs are formed from gold or silver nanoparticles in the 40-80 nm size range. A chemical dye is installed on the nanoparticle surface, and the nanoparticles are then aggregated into ensembles of {approx}100 to 500 nm diameter, prior to being coated with silica. The silica shell protects the finished SANA from

  11. Seals and sealing handbook

    CERN Document Server

    Flitney, Robert K

    2014-01-01

    Seals and Sealing Handbook, 6th Edition provides comprehensive coverage of sealing technology, bringing together information on all aspects of this area to enable you to make the right sealing choice. This includes detailed coverage on the seals applicable to static, rotary and reciprocating applications, the best materials to use in your sealing systems, and the legislature and regulations that may impact your sealing choices. Updated in line with current trends this updated reference provides the theory necessary for you to select the most appropriate seals for the job and with its 'Failur

  12. A finite-volume numerical method to calculate fluid forces and rotordynamic coefficients in seals

    Science.gov (United States)

    Athavale, M. M.; Przekwas, A. J.; Hendricks, R. C.

    1992-01-01

    A numerical method to calculate rotordynamic coefficients of seals is presented. The flow in a seal is solved by using a finite-volume formulation of the full Navier-Stokes equations with appropriate turbulence models. The seal rotor is perturbed along a diameter such that the position of the rotor is a sinusoidal function of time. The resulting flow domain changes with time, and the time-dependent flow in the seal is solved using a space conserving moving grid formulation. The time-varying fluid pressure reaction forces are then linked with the rotor center displacement, velocity and acceleration to yield the rotordynamic coefficients. Results for an annular seal are presented, and compared with experimental data and other more simplified numerical methods.

  13. Fluid-Structure Interaction Analysis on Turbulent Annular Seals of Centrifugal Pumps during Transient Process

    Directory of Open Access Journals (Sweden)

    Qinglei Jiang

    2011-01-01

    Full Text Available The current paper studies the influence of annular seal flow on the transient response of centrifugal pump rotors during the start-up period. A single rotor system and three states of annular seal flow were modeled. These models were solved using numerical integration and finite difference methods. A fluid-structure interaction method was developed. In each time step one of the three annular seal models was chosen to simulate the annular seal flow according to the state of rotor systems. The objective was to obtain a transient response of rotor systems under the influence of fluid-induced forces generated by annular seal flow. This method overcomes some shortcomings of the traditional FSI method by improving the data transfer process between two domains. Calculated results were in good agreement with the experimental results. The annular seal was shown to have a supportive effect on rotor systems. Furthermore, decreasing the seal clearance would enhance this supportive effect. In the transient process, vibration amplitude and critical speed largely changed when the acceleration of the rotor system increased.

  14. Brush seal leakage performance with gaseous working fluids at static and low rotor speed conditions

    Science.gov (United States)

    Carlile, Julie A.; Hendricks, Robert C.; Yoder, Dennis A.

    1992-01-01

    The leakage performance of a brush seal with gaseous working fluids at static and low rotor speed conditions was studied. The leakage results included for air, helium, and carbon dioxide at several bristle/rotor interferences. Also, the effects of packing a lubricant into the bristles and also of reversing the pressure drop across the seal were studied. Results were compared to that of an annular seal at similar operating conditions. In order to generalize the results, they were correlated using corresponding state theory. The brush seal tested had a bore diameter of 3.792 cm (1.4930 in.), a fence height of 0.0635 cm (0.025 in.), and 1800 bristles/cm circumference (4500 bristles/in. circumference). Various bristle/rotor radial interferences were achieved by using a tapered rotor. The brush seal reduced the leakage in comparison to the annular seal, up to 9.5 times. Reversing the pressure drop across the brush seal produced leakage rates approximately the same as that of the annular seal. Addition of a lubricant reduced the leakage by 2.5 times. The air and carbon dioxide data were successfully correlated using corresponding state theory. However, the helium data followed a different curve than the air and carbon dioxide data.

  15. Excitation by flows in seals and clearances. Part 1: Introduction: Fluid-structure-interactions in rotordynamics. Part 2: Identification of rotordynamic coefficients of annular seals

    Science.gov (United States)

    Nordmann, R.

    The fluid-structure interactions in rotor dynamics and the identification of rotor dynamic coefficients of annular seals are studied. The different fluid forces acting in the neck ring, the interstage seals, the balance pistons, the impellers and the oil film bearings of pumps are reviewed. These forces can have a large influence on the bending vibrations of a pump rotor. Theoretical and experimental models of fluid elements and of rotordynamics are presented. Simulations of the rotordynamic behavior show that the fluid forces of most elements can be described by linear-force relations. A theoretical model and an indentification procedure are presented to determine the dynamic coefficients of seals. The identified parameters confirm the assumptions in modeling and point out that the stiffness and damping characteristics of seals are significant for the stability behavior of pumps.

  16. Innovative technology summary report: Sealed-seam sack suits

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-09-01

    Sealed-seam sack suits are an improved/innovative safety and industrial hygiene technology designed to protect workers from dermal exposure to contamination. Most of these disposable, synthetic-fabric suits are more protective than cotton suits, and are also water-resistant and gas permeable. Some fabrics provide a filter to aerosols, which is important to protection against contamination, while allowing air to pass, increasing comfort level of workers. It is easier to detect body-moisture breakthrough with the disposable suits than with cotton, which is also important to protecting workers from contamination. These suits present a safe and cost-effective (6% to 17% less expensive than the baseline) alternative to traditional protective clothing. This report covers the period from October 1996 to August 1997. During that time, sealed-seam sack suits were demonstrated during daily activities under normal working conditions at the C Reactor and under environmentally controlled conditions at the Los Alamos National Laboratory (LANL).

  17. Computational Fluid Dynamics (CFD) Analysis Of Optical Payload For Lasercomm Science (OPALS) sealed enclosure module

    Science.gov (United States)

    Anderson, Kevin R.; Zayas, Daniel; Turner, Daniel

    2012-01-01

    Computational Fluid Dynamics (CFD) using the commercial CFD package CFDesign has been performed at NASA Jet Propulsion Laboratory (JPL) California Institute of Technology (Caltech) in support of the Phaeton Early Career Hire Program's Optical Payload for Lasercomm Science (OPALS) mission. The OPALS project is one which involves an International Space Station payload that will be using forced convection cooling in a hermetically sealed enclosure at 1 atm of air to cool "off-the-shelf" vendor electronics. The CFD analysis was used to characterize the thermal and fluid flow environment within a complicated labyrinth of electronics boards, fans, instrumentation, harnessing, ductwork and heat exchanger fins. The paradigm of iteratively using CAD/CAE tools and CFD was followed in order to determine the optimum flow geometry and heat sink configuration to yield operational convective film coefficients and temperature survivability limits for the electronics payload. Results from this current CFD analysis and correlation of the CFD model against thermal test data will be presented. Lessons learned and coupled thermal / flow modeling strategies will be shared in this paper.

  18. Design, operation and validation of a new fluid-sealed direct shear apparatus capable of monitoring fault-related fluid flow to large displacements

    NARCIS (Netherlands)

    Giger, S.B.; Clennell, M.B.; Harbers, C.; Clark, P.; Ricchetti, M.; Heege, J.H. ter; Wassing, B.B.T.; Orlic, B.

    2011-01-01

    A new type of direct shear apparatus has been developed to allow for deformation of large and intact rock samples under fluid-sealed conditions. The sealed cell was specifically designed to monitor changes to fluid flow across the evolving rupture surface to large displacements (=120. mm), and effec

  19. On The Analysis of Labyrinth Seal Flow Induced Vibration by Oscillating Fluid Mechanics Method

    Institute of Scientific and Technical Information of China (English)

    ChenZuoyi; JingYouhao; 等

    1994-01-01

    A numerical model and a solution method to analyze the labyrinth seal flow induced vibration by Oscillating Fluid Mechanics Method(OFMM) are presented in this paper,including the basic equations and solution procedure to determine the oscillating velocity,pressure and the dynamic characteristic coefficients of Labyrinth seal such as the stiffness coefficients and damping coefficients.The results show that this method has the advantages of both less time consuming and high accuracy.In addition it can be applied to the field diagnosis of the vibration of the axis of turbomachinery system.

  20. Seal Technology Development for Advanced Component for Airbreathing Engines

    Science.gov (United States)

    Snyder, Philip H.

    2008-01-01

    Key aspects of the design of sealing systems for On Rotor Combustion/Wave Rotor (ORC/WR) systems were addressed. ORC/WR systems generally fit within a broad class of pressure gain Constant Volume Combustors (CVCs) or Pulse Detonation Combustors (PDCs) which are currently being considered for use in many classes of turbine engines for dramatic efficiency improvement. Technology readiness level of this ORC/WR approaches are presently at 2.0. The results of detailed modeling of an ORC/WR system as applied to a regional jet engine application were shown to capture a high degree of pressure gain capabilities. The results of engine cycle analysis indicated the level of specific fuel consumption (SFC) benefits to be 17 percent. The potential losses in pressure gain due to leakage were found to be closely coupled to the wave processes at the rotor endpoints of the ORC/WR system. Extensive investigation into the sealing approaches is reported. Sensitivity studies show that SFC gains of 10 percent remain available even when pressure gain levels are highly penalized. This indicates ORC/WR systems to have a high degree of tolerance to rotor leakage effects but also emphasizes their importance. An engine demonstration of an ORC/WR system is seen as key to progressing the TRL of this technology. An industrial engine was judged to be a highly advantageous platform for demonstration of a first generation ORC/WR system. Prior to such a demonstration, the existing NASA pressure exchanger wave rotor rig was identified as an opportunity to apply both expanded analytical modeling capabilities developed within this program and to identify and fix identified leakage issues existing within this rig. Extensive leakage analysis of the rig was performed and a detailed design of additional sealing strategies for this rig was generated.

  1. Seals and sealing handbook

    CERN Document Server

    Flitney, Robert K

    2007-01-01

    Wherever machinery operates there will be seals of some kind ensuring that the machine remains lubricated, the fluid being pumped does not leak, or the gas does not enter the atmosphere. Seals are ubiquitous, in industry, the home, transport and many other places. This 5th edition of a long-established title covers all types of seal by application: static, rotary, reciprocating etc. The book bears little resemblance to its predecessors, and Robert Flitney has re-planned and re-written every aspect of the subject. No engineer, designer or manufacturer of seals can afford to be without this uniq

  2. Combat Ration Network for Technology Implementation (CORANET II) Knurled Seal Heat Bar

    Science.gov (United States)

    2010-08-01

    Canavan Mr. Henderikus B. Bruins Rutgers, The State University of New Jersey The Center for Advanced Food Technology School of Enviromental and...the packaging specification for the use of a knurled seal bar. Although the results from Project 2004 were positive, a number of issues were...to produce pouches with the altered pattern. The seal plate caused perforations at the seal area. Analysis of pouches revealed the issues and the

  3. Glass sealing

    Energy Technology Data Exchange (ETDEWEB)

    Brow, R.K.; Kovacic, L.; Chambers, R.S. [Sandia National Labs., Albuquerque, NM (United States)

    1996-04-01

    Hernetic glass sealing technologies developed for weapons component applications can be utilized for the design and manufacture of fuel cells. Design and processing of of a seal are optimized through an integrated approach based on glass composition research, finite element analysis, and sealing process definition. Glass sealing procedures are selected to accommodate the limits imposed by glass composition and predicted calculations.

  4. An in vitro assessment of the sealing ability of resilon/epiphany using fluid filtration.

    Science.gov (United States)

    Biggs, Stephen G; Knowles, Kenneth I; Ibarrola, Jose L; Pashley, David H

    2006-08-01

    The aim of this in vitro study was to compare the sealing ability of Resilon/Epiphany to gutta-percha and Roth or AH Plus sealers. Leakage of the obturated roots was measured using the fluid filtration technique. There were eight groups of 12 teeth each. Group 1: obturated with Resilon/Epiphany; group 2: obturated with gutta-percha/Roth, allowed to set for 3 wk; group 3: obturated with gutta-percha/Roth; group 4: obturated with Resilon/Epiphany using a single cone; group 5: obturated with Resilon cones without using primer/sealer (positive control); group 6: obturated with gutta-percha/AH Plus; group 7: same as group 6, but allowed to set for 8 h; and group 8: sealed on the outside with three layers of nail varnish (negative control). The results showed that only the positive control (group 5) leaked significantly more (p < 0.05) than the other groups. There was no effect of time on leakage. Resilon/Epiphany was no better than gutta-percha/Roth or gutta-percha/AH Plus at sealing root canals.

  5. Magnelok technology: a complement to magnetorheological fluids

    Science.gov (United States)

    Carlson, J. David

    2004-07-01

    Magnetorheological or MR fluids have been successfully used to enable highly effective semi-active control systems in automobile primary suspensions to control unwanted motions in civil engineering structures and to provide force-feedback in steer-by-wire systems. A key to the successful use of MR fluids is an appreciation and understanding of the balance and trade-off between the magnetically controlled on-state force and the ever-present off-state viscous force. In all MR fluid applications, one must deal with the fact that MR fluids never fully decouple or go to zero force in their off-state. Magnelok devices are a magnetically controlled compliment to traditional MR fluid devices that have been developed to enable a true force decoupling in the off-state. Magnelok devices may be embodied as linear or rotary dampers, brakes, lockable struts or position holding devices. They are particularly suitable for lock/un-lock applications. Unlike MR fluid devices they contain no fluid yet they do provide a variable level of friction damping that is controlled by the magnitude of the applied magnetic field. Magnelok devices are low cost as they easily accommodate relatively loose mechanical tolerances and require no seals or accumulator. A variety of controllable Magnelok devices and applications are described.

  6. ChipSeal Inorganic Sealing Technology for Hermetic-Like Integrated Circuits. Volume 1

    Science.gov (United States)

    2000-09-01

    formation (Kerkendall voiding ) and is more susceptible to corrosive attack under adverse conditions. • Degradation of the metallization stack from...processed devices in standard and flip-chip formats, both with and without epoxy encapsulants or underfills . 17 4. Phase I - ChipSeal Process...significant number of bumps exhibited internal voids (Figure 24). A second reflow eliminated the voids open to the surface (Figure 25), but some

  7. Building America Case Study: Field Trial of an Aerosol-Based Enclosure Sealing Technology, Clovis, California

    Energy Technology Data Exchange (ETDEWEB)

    2016-05-01

    This report presents the results from several demonstrations of a new method for sealing building envelope air leaks using an aerosol sealing process developed by the Western Cooling Efficiency Center at UC Davis. The process involves pressurizing a building while applying an aerosol sealant to the interior. As air escapes through leaks in the building envelope, the aerosol particles are transported to the leaks where they collect and form a seal that blocks the leak. Standard blower door technology is used to facilitate the building pressurization, which allows the installer to track the sealing progress during the installation and automatically verify the final building tightness. Each aerosol envelope sealing installation was performed after drywall was installed and taped, and the process did not appear to interrupt the construction schedule or interfere with other trades working in the homes. The labor needed to physically seal bulk air leaks in typical construction will not be replaced by this technology. However, this technology is capable of bringing the air leakage of a building that was built with standard construction techniques and HERS-verified sealing down to levels that would meet DOE Zero Energy Ready Homes program requirements. When a developer is striving to meet a tighter envelope leakage specification, this technology could greatly reduce the cost to achieve that goal by providing a simple and relatively low cost method for reducing the air leakage of a building envelope with little to no change in their common building practices.

  8. Influence of Mineral Additives on the Technological Properties of Sealing Slurries for Geoengineering Works

    Directory of Open Access Journals (Sweden)

    Andrzej Gonet

    2006-10-01

    Full Text Available One of the most important factors influencing the efficiency of sealing and reinforcing the ground and rock mass with geoengineering methods is a proper selection of respective technological parameters in view of existing hydrogeological and geotechnical conditions.Selected mineral additives increase the sealing properties of fresh and set slurries. They also decrease the cost of the slurry, provide a method for utilizing the stored materials (additives, and consequently, lessen the risk of environmental pollution.The results of laboratory tests on the influence of selected mineral additives on technological properties of sealing slurries are presented in the paper.

  9. P TFE油封技术发展趋势%Development Trend of PTFE Oil Seal Technologies

    Institute of Scientific and Technical Information of China (English)

    胡泽华; 张红烨

    2015-01-01

    介绍聚四氟乙烯油封的研究发展过程以及目前国内外材料和结构的研究现状,展望聚四氟乙烯油封的发展趋势,指出PTFE油封总体技术方案应从流体动力学分析、油封结构深层次研发、油封唇口材料的深层次应用及油封台架试验验证方面入手,针对改善高转速下油封的跟随性、高温下唇口过盈力的保持及降低高线速度下唇口磨损方面进行重点技术研究,通过对油封腰部韧性、唇口回复性及油封润滑状态等方面的控制,来保证产品达到使用要求的性能与寿命。%The research and development process of Polytetrafluoroethylene ( PTFE) oil seal,and research status of its materials and structures at home and abroad were presented. Development trend of PTFE oil seal was prospected. It was pointed out that the overall technical scheme of PTFE oil seal should be started from the aspects of fluid dynamics analy⁃sis,the structure development of oil seal, the application of lip materials and the test verification of oil seal by bench test, study the key technologies including improving the following of oil lips in high rotational speed,maintaining the lip interfer⁃ence force of oil seal at high temperature and reducing the wear of seal lip under high linear speed,and ensure that prod⁃ucts met the requirements of the performance and use life through controlling the lubrication status of oil seal,the lip recov⁃ery and the toughness on the waist of seal lip.

  10. Sealed all-metal CO2 laser tube technology

    Science.gov (United States)

    Byron, Stanley; Laakmann, Peter

    A newly developed RF plasma configuration for CO2 lasers is described, that offers high performance at low cost, using an all-metal, sealed-off laser tube design. The plasma bore of 5-mm square cross section supports a free-space TEM(00) optical model and a laser power density 1/3 that of CO2 waveguide lasers, allowing fabrication of compact sealed-off CO2 lasers from 10 to 100 watts with good optical and mechanical integrity. Design and manufacturing factors are discussed that affect gas life, beam quality, modulation, optical stability, and cost.

  11. Ultrasound for non-invasive fluid droplet detection inside a sealed container

    Science.gov (United States)

    Glass, S. W.; Good, M. S.; Roy, S.; Luzi, F.

    2017-02-01

    Ultrasound has long been known to be capable of measuring water level. Zero-degree ultrasound transducers may be used to send an L-wave through the fluid and receive a reflected signal from the fluid/gas interface surface. The level of the fluid is proportional to the sound wave time of flight to traverse the water path. This approach may even be used from outside the fluid containment wall by sending the wave through the tank or pipe bottom. The approach, however, does not work well if there is only a thin layer of fluid consisting of one or two millimeters or even only a few droplets. Surface waves are also known to be sensitive to the presence or absence of fluid on a surface. A surface wave may be transmitted a significant distance by a transmitting transducer and then received by a similar transducer. If the surface along the wave path is wet with even a few droplets of fluid, the surface wave may be significantly attenuated. Generating and measuring such a surface wave from the opposite side of a tank or pipe containment wall and separating the near-wall surface wave from the far-wall surface wave, however, is more challenging. The feasibility of an approach for producing a surface wave on the opposite side of a steel plate to sense the presence or absence of fluid is discussed. This approach is supported by 2-D finite element modeling of the measurement configuration and by empirical demonstration of the technique's sensitivity. This technique was developed for measurement of a very small amount of fluid that may condense within a used nuclear fuel canister after it cools for several years. Early detection of fluid would provide advance warning of potential degradation to internal components in time for mitigation or management of the waste inside that container. Other potential applications include non-intrusive detection of trace liquids within any sealed container, within inaccessible plena of aircrafts or within other inaccessible complex welded skin

  12. Fluid dynamic modeling of a free piston engine with labyrinth seals

    Science.gov (United States)

    Larjola, Jaakko; Honkatukia, Juha; Sallinen, Petri; Backman, Jari

    2010-04-01

    Preliminary design and simulation of a free piston engine suitable for small-scale energy production in distributed energy systems is presented in this paper. The properties, particularly the properties of gas seals of the engine are simulated using a simulation program developed for this case, and the results are utilized in preliminary main design parameter selection. The engine simulation program was developed by combining and modifying the source codes of the simulation and calculation programs obtained from Helsinki University of Technology, Tampere University of Technology, and Lappeenranta University of Technology. Because of the contact-free labyrinth seal used in the piston, the efficiency of the motor is lower than the efficiency of a conventional motor with oil lubricated piston rings. On the other hand, the lack of bearing losses, and the lack of losses associated with a crankshaft system and a gearbox, as well as the lack of lubrication oil expenses, compensates this effect. As a net result, this new motor would perform slightly better than the conventional one. Being completely oil-free, it is very environmentally friendly, and its exhaust gases are completely free of oil residuals which are causing problems in normal gas motors.

  13. Study on Seal Technology for Nuclear Material Control

    Institute of Scientific and Technical Information of China (English)

    2002-01-01

    The seals have important application in nuclear safeguards, and are designed to record unauthorizedaccess or entry to inspected material and equipment. They can provide assurance for the continuity andintegrity of nuclear material accountancy. It is very useful to improve the inspection efficiency by means

  14. Problems and criteria of quality improvement in end face mechanical seal rings through technological methods

    Science.gov (United States)

    Tarelnik, V.; Belous, A.; Antoszewski, B.; Zukov, A.

    2017-08-01

    In this paper are presented the recommendations for material’s selections of the mechanical seals rings and basic productive and operating requirements. The system of a directional selection of technology that ensures the required quality of working surfaces of the mechanical seals rings covers their entire life cycle. The mathematical frictional model is proposed as an instrument for calculating a linear and weighing abrasion of the mechanical seals rings and helps to improve selection’s criteria and the most rational method of strengthening.

  15. Field Test of Advanced Duct-Sealing Technologies Within the Weatherization Assistance Program

    Energy Technology Data Exchange (ETDEWEB)

    Ternes, MP

    2001-12-05

    A field test of an aerosol-spray duct-sealing technology and a conventional, best-practice approach was performed in 80 homes to determine the efficacy and programmatic needs of the duct-sealing technologies as applied in the U.S. Department of Energy Weatherization Assistance Program. The field test was performed in five states: Iowa, Virginia, Washington, West Virginia, and Wyoming. The study found that, compared with the best-practice approach, the aerosol-spray technology is 50% more effective at sealing duct leaks and can potentially reduce labor time and costs for duct sealing by 70%, or almost 4 crew-hours. Further study to encourage and promote use of the aerosol-spray technology within the Weatherization Assistance Program is recommended. A pilot test of full production weatherization programs using the aerosol-spray technology is recommended to develop approaches for integrating this technology with other energy conservation measures and minimizing impacts on weatherization agency logistics. In order to allow or improve adoption of the aerosol spray technology within the Weatherization Assistance Program, issues must be addressed concerning equipment costs, use of the technology under franchise arrangements with Aeroseal, Inc. (the holders of an exclusive license to use this technology), software used to control the equipment, safety, and training. Application testing of the aerosol-spray technology in mobile homes is also recommended.

  16. Sealing vessels up to 7 mm in diameter solely with ultrasonic technology

    Directory of Open Access Journals (Sweden)

    Timm RW

    2014-07-01

    Full Text Available Richard W Timm, Ryan M Asher, Karalyn R Tellio, Alissa L Welling, Jeffrey W Clymer, Joseph F Amaral Ethicon Inc., Cincinnati, OH, USA Introduction: Ultrasonic energy is a mainstay in the armamentarium of surgeons, providing multifunctionality, precision, and control when dissecting and sealing vessels up to 5 mm in diameter. Historically, the inability to seal vessels in the 5–7 mm range has been perceived as an inherent limitation of ultrasonic technology. The purpose of this study was to evaluate sealing of vessels up to 7 mm in diameter with an ultrasonic device that modulates energy delivery during the sealing period. Methods: In ex vivo benchtop and in vivo acute and survival preclinical models, a new ultrasonic device, Harmonic ACE®+7 Shears (Harmonic 7, was compared with advanced bipolar devices in sealing vessels 1–7 mm in diameter with respect of burst pressure, seal reliability, and seal durability. Lateral thermal damage and transection time were also evaluated. Results: Ex vivo tests of Harmonic 7 demonstrated significantly greater median burst pressures than an advanced bipolar device both for vessels <5 mm in diameter (1,078 mmHg and 836 mmHg, respectively, P=0.046 and for those in the range of 5–7 mm (1,419 mmHg and 591 mmHg, P<0.001. In vivo tests in porcine and caprine models demonstrated similar rates of hemostasis between Harmonic 7 and advanced bipolar devices, with high success rates at initial transection and seal durability of 100% after a 30-day survival period. Conclusion: Sealing 5–7 mm vessels is not a limitation of the type of energy used but of how energy is delivered to tissue. These studies document the ability of ultrasonic energy alone to reliably seal large vessels 5–7 mm in diameter, with significantly greater burst pressure observed in in vitro studies than those observed with an advanced bipolar technology when energy delivery is modulated during the sealing cycle. Furthermore, the seals created in

  17. SERS-active nanoparticles as a barcoding technology for tags and seals

    Energy Technology Data Exchange (ETDEWEB)

    Brown, Leif O [Los Alamos National Laboratory; Doorn, Stephen K [Los Alamos National Laboratory; Merkle, Peter B [SNL

    2009-01-01

    In this paper, we present our work to modernize tagging and sealing technologies for international safeguards applications. Our work combines technologies developed at both Los Alamos National Laboratory (LANL), and Sandia National Laboratories (SNL), to offer a passive tag and seal system that can be applied and verified in field, with minimal training for on-site personnel, along with a low per-seal cost. Here, we focus primarily on LANL technology: the use of Surface Enhanced Raman Scattering (SERS) as an inexpensive verification tool. Our nanoparticles offer unique SERS responses, which we can then use to incorporate robust barcoding into tag materials. We describe this technology in more detail, offer preliminary results, and outline integration with SNL developments.

  18. 连续注排式气体离心密封的性能分析%Performance Analysis of the Gas Centrifugal Seal with Continuous Injection and Elimination of the Sealing Fluid

    Institute of Scientific and Technical Information of China (English)

    智冬; 李双喜; 张秋翔; 蔡纪宁

    2012-01-01

    针对普通离心密封用于气体场合下存在的问题,提出一种带有连续注排密封液结构的新型离心密封,介绍该密封的工作原理及特点.基于VOF方法,利用Fluent软件对离心密封内的气液两相流进行数值模拟,求得密封液流量、气液交界面位置以及压力折减系数等密封特性参数,研究操作参数和结构参数对密封性能的影响.结果表明:该密封适用于高转速下的气体密封,在一定的密封间隙范围内,增加转轴转速会减少密封液的流量,而在密封液进口处设置环形积水槽会增加密封液的流量;增加密封液的注入压力,减小密封间隙有助于降低环形漩涡的影响.%Aimed at the problems of the common centrifugal seal for sealing gas, a configuration of the new-type centrif ugal seal device with continuous injection and elimination of the sealing fluid was proposed,and the operating principle and feature of the seal were introduced. The software Fluent was used for the numerical simulations of internal gas-liquid flow in the centrifugal seal,applying the Volume of Fluid(VOF) method. The mass flow rate of the sealing fluid,the air-liquid in terface and the reduced coefficient of pressure were gained. The influences of the operation parameters and structural pa rameters on the sealing property were studied. The investigation results show that the seal is suit for the condition of gas seal of high speed. Within certain ranges of the sealing gap,the flow rate of the sealing fluid is reduced with the raise of the rotor speed,and is increased when the annular water tank is set at the entrance of the sealing fluid. The influence of the an nular vortex can be reduced by increasing the injection pressure of the sealing fluid and decreasing the seal gap.

  19. Technology, safety, and costs of decommissioning a reference large irradiator and reference sealed sources

    Energy Technology Data Exchange (ETDEWEB)

    Haffner, D.R.; Villelgas, A.J. [Pacific Northwest Lab., Richland, WA (United States)

    1996-01-01

    This report contains the results of a study sponsored by the US Nuclear Regulatory Commission (NRC) to examine the decommissioning of large radioactive irradiators and their respective facilities, and a broad spectrum of sealed radioactive sources and their respective devices. Conceptual decommissioning activities are identified, and the technology, safety, and costs (in early 1993 dollars) associated with decommissioning the reference large irradiator and sealed source facilities are evaluated. The study provides bases and background data for possible future NRC rulemaking regarding decommissioning, for evaluation of the reasonableness of planned decommissioning actions, and for determining if adequate funds are reserved by the licensees for decommissioning of their large irradiator or sealed source facilities. Another purpose of this study is to provide background and information to assist licensees in planning and carrying out the decommissioning of their sealed radioactive sources and respective facilities.

  20. Computational fluid dynamics and experimental study of inter-stage seal clearance on submersible well pump

    Directory of Open Access Journals (Sweden)

    Xiongfa Gao

    2016-02-01

    Full Text Available In this article, a typical submersible well pump was investigated to study the effects of inter-stage leakage on the inner flow field and external characteristics. The whole flow field of the model pump with different seal clearances was simulated by computational fluid dynamics software. The inter-stage clearance leakage calculated by numerical simulation was compared with the values obtained by the empirical formula. The pressure values were recorded with the arrangement of monitor points in the inter-stage clearance, inlet region, and outlet region, which aimed to study the effects of the change of inter-stage clearance pressure on the pump performance. Meanwhile, a comparative analysis of numerical simulation and performance test of the pump was conducted further. The results showed that the leakage at the small clearance is close to the value calculated using empirical formula. But when the clearance is large, the discrepancy between the simulation result and empirical value inclines. Comparing the numerical results of three kinds of clearance leakage, we found that the clearance leakage could not be ignored in the simulation since it has a large effect on the prediction of pump efficiency and head.

  1. Hydraulic fracturing chemicals and fluids technology

    CERN Document Server

    Fink, Johannes

    2013-01-01

    When classifying fracturing fluids and their additives, it is important that production, operation, and completion engineers understand which chemical should be utilized in different well environments. A user's guide to the many chemicals and chemical additives used in hydraulic fracturing operations, Hydraulic Fracturing Chemicals and Fluids Technology provides an easy-to-use manual to create fluid formulations that will meet project-specific needs while protecting the environment and the life of the well. Fink creates a concise and comprehensive reference that enables the engineer to logically select and use the appropriate chemicals on any hydraulic fracturing job. The first book devoted entirely to hydraulic fracturing chemicals, Fink eliminates the guesswork so the engineer can select the best chemicals needed on the job while providing the best protection for the well, workers and environment. Pinpoints the specific compounds used in any given fracturing operation Provides a systematic approach to class...

  2. Non-contacting fluid ring seal systems for railcar axle bearing systems: Quarterly progress report No. 4, March 16-June 15, 1988

    Energy Technology Data Exchange (ETDEWEB)

    1988-06-01

    The main objectives of this DOE contract is the technical development of a practical, cost effective Fluid Ring seal system capable of: Drastically reducing locomotive drawbar traction power requirements by lowering seal friction losses prevalent in present railcar axle bearing systems; increasing reliability and safety of railroad cars by minimizing bearing lubricant leakage and minimizing bearing ''hot boxes''; and improving the productivity of the railway transportation systems by reducing rolling stock ''outages'' due to long seal life. Listed in this report are the seal test data.

  3. NASA's Cryogenic Fluid Management Technology Project

    Science.gov (United States)

    Tramel, Terri L.; Motil, Susan M.

    2008-01-01

    The Cryogenic Fluid Management (CFM) Project's primary objective is to develop storage, transfer, and handling technologies for cryogens that will support the enabling of high performance cryogenic propulsion systems, lunar surface systems and economical ground operations. Such technologies can significantly reduce propellant launch mass and required on-orbit margins, reduce or even eliminate propellant tank fluid boil-off losses for long term missions, and simplify vehicle operations. This paper will present the status of the specific technologies that the CFM Project is developing. The two main areas of concentration are analysis models development and CFM hardware development. The project develops analysis tools and models based on thermodynamics, hydrodynamics, and existing flight/test data. These tools assist in the development of pressure/thermal control devices (such as the Thermodynamic Vent System (TVS), and Multi-layer insulation); with the ultimate goal being to develop a mature set of tools and models that can characterize the performance of the pressure/thermal control devices incorporated in the design of an entire CFM system with minimal cryogen loss. The project does hardware development and testing to verify our understanding of the physical principles involved, and to validate the performance of CFM components, subsystems and systems. This database provides information to anchor our analytical models. This paper describes some of the current activities of the NASA's Cryogenic Fluid Management Project.

  4. Seals For Cryogenic Turbomachines

    Science.gov (United States)

    Hendricks, Robert C.; Tam, L. T.; Braun, M. J.; Vlcek, B. L.

    1988-01-01

    Analysis considers effects of seals on stability. Report presents method of calculation of flows of cryogenic fluids through shaft seals. Key to stability is local average velocity in seal. Local average velocity strongly influenced by effects of inlet and outlet and injection of fluid.

  5. Cryogenic Fluid Management Technology Development Roadmaps

    Science.gov (United States)

    Stephens, J. R.; Johnson, W. L.

    2017-01-01

    Advancement in Cryogenic Fluid Management (CFM) Technologies is essential for achieving NASA's future long duration missions. Propulsion systems utilizing cryogens are necessary to achieve mission success. Current State Of the Art (SOA) CFM technologies enable cryogenic propellants to be stored for several hours. However, some envisioned mission architectures require cryogens to be stored for two years or longer. The fundamental roles of CFM technologies are long term storage of cryogens, propellant tank pressure control and propellant delivery. In the presence of heat, the cryogens will "boil-off" over time resulting in excessive pressure buildup, off-nominal propellant conditions, and propellant loss. To achieve long term storage and tank pressure control, the CFM elements will intercept and/or remove any heat from the propulsion system. All functions are required to perform both with and without the presence of a gravitational field. Which CFM technologies are required is a function of the cryogens used, mission architecture, vehicle design and propellant tank size. To enable NASA's crewed mission to the Martian surface, a total of seventeen CFM technologies have been identified to support an In-Space Stage and a Lander/Ascent Vehicle. Recognizing that FY2020 includes a Decision Point regarding the In-Space Stage Architecture, a set of CFM Technology Development Roadmaps have been created identifying the current Technology Readiness Level (TRL) of each element, current technology "gaps", and existing technology development efforts. The roadmaps include a methodical approach and schedule to achieve a flight demonstration in FY2023, hence maturing CFM technologies to TRL 7 for infusion into the In-Space Stage Preliminary Design.

  6. Frame and edge seal technology: A state of the art survey

    Science.gov (United States)

    Thyholt, Marit; Andresen, Inger; Hugdal, Berit; Aschehoug, Oeyvind

    1994-04-01

    In windows, the glazing is traditionally mounted in an operable or fixed frame, made of wood, metal (steel or aluminum), or PVC. The glazing component in solar collectors and solar walls is also typically mounted in a frame. The purpose of the frame is to protect the vulnerable edge of the glazing and give structural stability, which is especially important in operable windows. Sealed multipane glazings are almost exclusively fabricated with a metal (aluminum or galvanized steel) spacer bar along the edges. New advanced glazings will require new types of frame and edge seal products. As the insulation properties of the glazing itself reach a performance close to that of well-insulated opaque walls, the thermal bridging caused by the spacer bars and the frames will be unacceptable, even for wooden windows. The new glazings will also integrate other functions, which again will influence the design of the frames. There are already quite a few new technological developments in this field. New materials and products for the edge seal and the frame are being developed, and computer calculations gradually take over the manual analysis and laboratory testing of new products. The objective of this IEA Task 18 Case Study is to investigate the influence of the frame and glazing edge seal on the total U-value of a glazing system, to develop improved test and calculation methods, and to design, construct, and test low thermal loss frames for use in advanced glazing applications.

  7. Large Gap Sealing Technology%大间隙密封技术

    Institute of Scientific and Technical Information of China (English)

    石绍清

    2000-01-01

    The hydrostatic testing machine for seamless steel pipes adopts traditional sealing methods. which is of very low efficiency, the consumption of seal rings is surprisingly high, and the cost is also very high, The large gap sealing technology is described in this paper which has been applied on the hydrostatic testing machine for seamless steel pipes has completely eliminated damages to the seal, the pipes and the thread in the transportation process of steel pipes going into and coming out of the hydrostatic tesing device.%无缝钢管水压试验机采用传统的密封方式,生产效率极低,密封圈消耗惊人,成本居高不下。本文介绍的大间隙密封技术,应用到无缝钢管水压试验机上,完全消除了钢管进出水压试验装置的输送过程中对密封、钢管及丝扣产生的损坏。

  8. Optimization Analysis of the Sealing Performance of Rectangular Sealing Ring of Automotive Brake Fluid Filling Gun%汽车制动液加注枪矩形密封圈性能的优化分析

    Institute of Scientific and Technical Information of China (English)

    张和平; 黄华坤

    2013-01-01

    利用有限元分析软件ANSYS,对汽车制动液加注枪与壶口的矩形密封圈的密封性能进行有限元分析.通过分析影响密封性的因素,如压缩率、摩擦因数、壶口内径、壶口壁厚,得到密封面接触压力随各因素变化的关系曲线.通过正交试验,确定各因素对密封面接触压力的贡献率,得到密封性能最优时各因素的取值.结果表明,压缩率对密封性的影响最大,其次是摩擦因数、壶口内径和壶口壁厚.%The sealing performance of the rectangular sealing ring between the automotive brake fluid filling gun and the spout of brake fluid pot was analyzed by using finite element analysis software ANSYS.By analyzing the factors influencing the sealing performance,such as compression rate,friction coefficient,the spout inner diameter and wall thickness,the variations of sealing surface contact pressure along with these factors were obtained.Through orthogonal experiments,the contribution rate of each factor on the sealing surface contact pressure was determined,and the optimal value of each factor was selected to get the best sealing performance.The results show that the influence of compression ratio on the sealing performance is the biggest,followed by friction coefficient,the spout inner diameter and wall thickness of brake fluid pot.

  9. Non-contacting fluid ring seal systems for railcar axle bearing systems: Quarterly progress report No. 1, June 15 to September 15, 1987

    Energy Technology Data Exchange (ETDEWEB)

    1987-01-01

    The main objectives of this DOE contract is the technical development of a practical, cost effective Fluid Ring seal system capable of: Drastically reducing locomotive drawbar traction power requirements by lowering seal friction losses prevalent in present railcar axle bearing systems; increasing reliability and safety of railroad cars by minimizing bearing lubricant leakage and minimizing bearing ''hot boxes''; and improving the productivity of the railway transportation systems by reducing rolling stock ''outages'' due to long seal life. 14 refs.

  10. Development of intermediate temperature sodium nickel chloride rechargeable batteries using conventional polymer sealing technologies

    Science.gov (United States)

    Chang, Hee Jung; Lu, Xiaochuan; Bonnett, Jeff F.; Canfield, Nathan L.; Son, Sori; Park, Yoon-Cheol; Jung, Keeyoung; Sprenkle, Vincent L.; Li, Guosheng

    2017-04-01

    Developing advanced and reliable electrical energy storage systems is critical to fulfill global energy demands and stimulate the growth of renewable energy resources. Sodium metal halide batteries have been under serious consideration as a low cost alternative energy storage device for stationary energy storage systems. Yet, there are number of challenges to overcome for the successful market penetration, such as high operating temperature and hermetic sealing of batteries that trigger an expensive manufacturing process. Here we demonstrate simple, economical and practical sealing technologies for Na-NiCl2 batteries operated at an intermediate temperature of 190 °C. Conventional polymers are implemented in planar Na-NiCl2 batteries after a prescreening test, and their excellent compatibilities and durability are demonstrated by a stable performance of Na-NiCl2 battery for more than 300 cycles. The sealing methods developed in this work will be highly beneficial and feasible for prolonging battery cycle life and reducing manufacturing cost for Na-based batteries at elevated temperatures (<200 °C).

  11. Ceramic Seal.

    Energy Technology Data Exchange (ETDEWEB)

    Smartt, Heidi A. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Romero, Juan A. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Custer, Joyce Olsen [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Hymel, Ross W. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Krementz, Dan [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL); Gobin, Derek [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL); Harpring, Larry [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL); Martinez-Rodriguez, Michael [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL); Varble, Don [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL); DiMaio, Jeff [Tetramer Technologies, Pendleton, SC (United States); Hudson, Stephen [Tetramer Technologies, Pendleton, SC (United States)

    2016-11-01

    Containment/Surveillance (C/S) measures are critical to any verification regime in order to maintain Continuity of Knowledge (CoK). The Ceramic Seal project is research into the next generation technologies to advance C/S, in particular improving security and efficiency. The Ceramic Seal is a small form factor loop seal with improved tamper-indication including a frangible seal body, tamper planes, external coatings, and electronic monitoring of the seal body integrity. It improves efficiency through a self-securing wire and in-situ verification with a handheld reader. Sandia National Laboratories (SNL) and Savannah River National Laboratory (SRNL), under sponsorship from the U.S. National Nuclear Security Administration (NNSA) Office of Defense Nuclear Nonproliferation Research and Development (DNN R&D), have previously designed and have now fabricated and tested Ceramic Seals. Tests have occurred at both SNL and SRNL, with different types of tests occurring at each facility. This interim report will describe the Ceramic Seal prototype, the design and development of a handheld standalone reader and an interface to a data acquisition system, fabrication of the seals, and results of initial testing.

  12. Seal design alternatives study

    Energy Technology Data Exchange (ETDEWEB)

    Van Sambeek, L.L. [RE/SPEC Inc., Rapid City, SD (US); Luo, D.D.; Lin, M.S.; Ostrowski, W.; Oyenuga, D. [Parsons Brinckerhoff Quade & Douglas, Inc., San Francisco, CA (US)

    1993-06-01

    This report presents the results from a study of various sealing alternatives for the WIPP sealing system. Overall, the sealing system has the purpose of reducing to the extent possible the potential for fluids (either gas or liquid) from entering or leaving the repository. The sealing system is divided into three subsystems: drift and panel seals within the repository horizon, shaft seals in each of the four shafts, and borehole seals. Alternatives to the baseline configuration for the WIPP seal system design included evaluating different geometries and schedules for seal component installations and the use of different materials for seal components. Order-of-magnitude costs for the various alternatives were prepared as part of the study. Firm recommendations are not presented, but the advantages and disadvantages of the alternatives are discussed. Technical information deficiencies are identified and studies are outlined which can provide required information.

  13. The Improvement of Magnetic Fluid Centrifugal Sealing Structure%磁流体离心密封结构的改进设计

    Institute of Scientific and Technical Information of China (English)

    左英杰; 姚新港; 刘同冈; 刘书进

    2011-01-01

    Magnetic fluid seal is used for the liquid seal ,the magnetie fluid can be emulsified and deteriorated by the sealed liquid medium. Using the eapillary phenomenon of hydrodynamics,the magnetic fluid centrifugal sealing stmcture was improved by adding a subsidiary structure to form a small gap between the axis of rotation and the subsidiary structure.The capillary of small gap can prevent the contact of magnetic fluid and sealed liquid medium. The results of experiments show that the structure has good sealing performance for liquid seal.%磁流体密封在密封液体时,被密封的液体介质与磁流体接触会引起磁流体乳化、变质,导致密封失效.结合流体力学中的毛细管现象,对磁流体离心密封结构进行改进,即在密封结构中增加一附属结构,在附属结构和旋转轴之间形成一个很小的间隙,利用小间隙产生的毛细作用将密封液体与磁流体分隔开来,防止密封液体对磁流体的影响.试验结果表明,该密封结构具有良好的密封性能,对液体具有更好的密封效果.

  14. ENVIRONMENTAL TECHNOLOGY VERIFICATION REPORT, PERFORMANCE TEST RESULTS FOR THE A AND A ENVIRONMENTAL SEALS' SEAL ASSIST SYSTEM (SAS), PHASE I--TECHNOLOGY VERIFICATION REPORT

    Science.gov (United States)

    The report presents results of tests determining the efficacy of A&A Environmental Seals, Inc's Seal Assist System (SAS) in preventing natural gas compressor station's compressor rod packing leaks from escaping into the atmosphere. The SAS consists of an Emission Containment Glan...

  15. Development of Mechanical Sealing and Laser Welding Technology to Instrument Thermocouple for Nuclear Fuel Test Rod

    Energy Technology Data Exchange (ETDEWEB)

    Joung, Chang-Young; Ahn, Sung-Ho; Hong, Jin-Tae; Kim, Ka-Hye; Huh, Sung-Ho [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

    2015-05-15

    Zircaloy-4 of the nuclear fuel test rod, AISI 316L of the mechanical sealing parts, and the MI (mineral insulated) cable at a thermocouple instrumentation are hetero-metals, and are difficult to weld to dissimilar materials. Therefore, a mechanical sealing method to instrument the thermocouple should be conducted using two kinds of sealing process as follows: One is a mechanical sealing process using Swagelok, which is composed of sealing components that consists of an end-cap, a seal tube, a compression ring and a Swagelok nut. The other is a laser welding process used to join a seal tube, and an MI cable, which are made of the same material. The mechanical sealing process should be sealed up with the mechanical contact compressed by the strength forced between a seal tube and an end-cap, and the laser welding process should be conducted to have no defects on the sealing area between a seal tube and an MI cable. Therefore, the mechanical sealing and laser welding techniques need to be developed to accurately measure the centerline temperature of the nuclear fuel test rod in an experimental reactor. The mechanical sealing and laser welding tests were conducted to develop the thermocouple instrumentation techniques for the nuclear fuel test rod. The optimum torque value of a Swagelok nut to seal the mechanical sealing part between the end-cap and seal tube was established through various torque tests using a torque wrench. The optimum laser welding conditions to seal the welding part between a seal tube and an MI cable were obtained through various welding tests using a laser welding system.

  16. Supercritical fluids technology for clean biofuel production

    Institute of Scientific and Technical Information of China (English)

    Dongsheng Wen; H.Jiang; Kai Zhang

    2009-01-01

    Biofuels are liquid or gaseous fuels that are predominantly produced from biomass for transport sector applications.As biofuels are renewable,sustainable,carbon neutral and environmentally benign,they have been proposed as promising alternative fuels for gasoline and diesel engines.This paper reviews state-of-the-art application of the supercritical fluid(SCF)technique in biofuels production that includes biodiesel from vegetable oils via the transesterification process,bio-hydrogen from the gasification and bio-oil from the lique-faction of biomass,with biodiesel production as the main focus. The global biofuel situation and biofuel economics are also reviewed.The SCF has been shown to be a promising technique for future large-scale biofuel production,especially for biodiesel production from waster oil and fat.Compared with conventional biofuel production methods,the SCF technology possesses a number of advantages that includes fast inetics,high fuel production rate,ease of continuous operation and elimination of the necessity of catalysts.The harsh operation environment,i.e. the high temperature and high pressure,and its request on the materials and associated cost are the main concerns for its wide application.

  17. Egyptian diatomite as high fluid loss squeeze slurry in sealing fractures and

    Directory of Open Access Journals (Sweden)

    A.M. Al-Sabagh

    2016-09-01

    Full Text Available Lost circulation is the most costly mud related drilling problem, and induced fracture. Water slurry of diatomite is used as the high fluid loss squeeze slurry in the treatment of lost circulation and in decreasing fluid loss. Egypt has diatomite deposits, especially in El-Fayuom Depression. Fourteen samples were collected from Qasr El-Sagha at the northern shore of Birket Qarun. Samples were examined to identify the diatom species then subjected to X-ray fluorescence, XRD and grain size distribution tests. A total of 38 species related to 13 diatom genera were identified. Cocconeis, Epithemia and Rhopalodia were the predominant genera. The diatomaceous earth which acts as a filter aid material was tested with different additives; bentonite, lime, finely divided paper, polymer, barite and different concentrations with different types of lost circulation materials (LCM to form a high fluid loss squeeze slurry. As a result the required time for collecting the filtrate was decreased to be in the range of 50 s to 1 min and 49 s comparing with the international standard which recommended the filtrate should be collected maximum within 2–3 min.

  18. 汽车发动机的密封技术浅析%Analysis of Sealing Technology of Automotive Engine

    Institute of Scientific and Technical Information of China (English)

    谢莹

    2015-01-01

    在汽车技术飞速发展的今天,客户对汽车发动机的要求不断提高,追求更高的动力性、经济性及排放性能,对发动机零部件可靠性要求更高,其中,发动机的密封性能是评价汽车质量的一个重要指标,汽车运行中发动机工作介质的泄漏,会直接影响汽车发动机的工况。因此,发动机密封技术研究日益成为当前汽车发展的主题。本文从密封设计、密封质量问题、密封验证等方面阐述了当前对汽车发动机密封技术发展的要求。%With the rapid development of automotive technology, the customer's demand for automotive engine is increasing, pursuing higher power, economy and emissions performance, and higher reliability of engine parts, in which the sealing performance of the engine is an important indicator of evaluating the quality of the car. The engine working medium leak in the operation of car will directly affect the working conditions of automobile engine. Therefore, the research on engine sealing technology is becoming the main subject of current vehicle development increasingly. This paper expounds the requirements for the development of current automotive engine sealing technology from sealing design, sealing quality and sealing verification.

  19. Geothermal Produced Fluids: Characteristics, Treatment Technologies, and Management Options

    Energy Technology Data Exchange (ETDEWEB)

    Finster, Molly; Clark, Corrie; Schroeder, Jenna; Martino, Louis

    2015-10-01

    Geothermal power plants use geothermal fluids as a resource and create waste residuals as part of the power generation process. Both the geofluid resource and the waste stream are considered produced fluids. The chemical and physical nature of produced fluids can have a major impact on the geothermal power industry and can influence the feasibility of geothermal power development, exploration approaches, power plant design, operating practices, and the reuse or disposal of residuals. In general, produced fluids include anything that comes out of a geothermal field and that subsequently must be managed on the surface. These fluids vary greatly depending on the geothermal reservoir being harnessed, power plant design, and the life cycle stage in which the fluid exists, but generally include water and fluids used to drill geothermal wells, fluids used to stimulate wells in enhanced geothermal systems, and makeup and/or cooling water used during operation of a geothermal power plant. Additional geothermal-related produced fluids include many substances that are similar to waste streams from the oil and gas industry, such as scale, flash tank solids, precipitated solids from brine treatment, hydrogen sulfide, and cooling-tower-related waste. This review paper aims to provide baseline knowledge on specific technologies and technology areas associated with geothermal power production. Specifically, this research focused on the management techniques related to fluids produced and used during the operational stage of a geothermal power plant; the vast majority of which are employed in the generation of electricity. The general characteristics of produced fluids are discussed. Constituents of interest that tend to drive the selection of treatment technologies are described, including total dissolved solids, noncondensable gases, scale and corrosion, silicon dioxide, metal sulfides, calcium carbonate, corrosion, metals, and naturally occurring radioactive material. Management

  20. Tracer technology modeling the flow of fluids

    CERN Document Server

    Levenspiel, Octave

    2012-01-01

    A vessel’s behavior as a heat exchanger, absorber, reactor, or other process unit is dependent upon how fluid flows through the vessel.  In early engineering, the designer would assume either plug flow or mixed flow of the fluid through the vessel.  However, these assumptions were oftentimes inaccurate, sometimes being off by a volume factor of 100 or more.  The result of this unreliable figure produced ineffective products in multiple reaction systems.   Written by a pioneering researcher in the field of chemical engineering, the tracer method was introduced to provide more accurate flow data.  First, the tracer method measured the actual flow of fluid through a vessel.  Second, it developed a suitable model to represent the flow in question.  Such models are used to follow the flow of fluid in chemical reactors and other process units, like in rivers and streams, or solid and porous structures.  In medicine, the tracer method is used to study the flow of chemicals—harmful  and harmless—in the...

  1. Preparation of drug delivery systems using supercritical fluid technology.

    Science.gov (United States)

    Kompella, U B; Koushik, K

    2001-01-01

    Small changes in temperature and pressure near the critical region induce dramatic changes in the density and solubility of supercritical fluids, thereby facilitating the use of environmentally benign agents such as CO2 for their solvent and antisolvent properties in processing a wide variety of materials. While supercritical fluid technologies have been in commercial use in the food and chromatography industries for several years, only recently has this technology made inroads in the formulation of drug delivery systems. This review summarizes some of the recent applications of supercritical fluid technology in the preparation of drug delivery systems. Drugs containing polymeric particles, plain drug particles, solute-containing liposomes, and inclusion complexes of drug and carrier have been formulated using this technology. Also, polymer separation using this technology is enabling the selection of a pure fraction of a polymer, thereby allowing a more precise control of drug release from polymeric delivery systems.

  2. Methods and systems for integrating fluid dispensing technology with stereolithography

    Energy Technology Data Exchange (ETDEWEB)

    Medina, Francisco (El Paso, TX); Wicker, Ryan (El Paso, TX); Palmer, Jeremy A. (Albuquerque, NM); Davis, Don W. (Albuquerque, NM); Chavez, Bart D. (Albuquerque, NM); Gallegos, Phillip L. (Albuquerque, NM)

    2010-02-09

    An integrated system and method of integrating fluid dispensing technologies (e.g., direct-write (DW)) with rapid prototyping (RP) technologies (e.g., stereolithography (SL)) without part registration comprising: an SL apparatus and a fluid dispensing apparatus further comprising a translation mechanism adapted to translate the fluid dispensing apparatus along the Z-, Y- and Z-axes. The fluid dispensing apparatus comprises: a pressurized fluid container; a valve mechanism adapted to control the flow of fluid from the pressurized fluid container; and a dispensing nozzle adapted to deposit the fluid in a desired location. To aid in calibration, the integrated system includes a laser sensor and a mechanical switch. The method further comprises building a second part layer on top of the fluid deposits and optionally accommodating multi-layered circuitry by incorporating a connector trace. Thus, the present invention is capable of efficiently building single and multi-material SL fabricated parts embedded with complex three-dimensional circuitry using DW.

  3. Non-contacting fluid ring seal systems for railcar axle bearing systems: Fifth quarterly report, June 16, 1988--September 15, 1988

    Energy Technology Data Exchange (ETDEWEB)

    1988-10-01

    During this fifth quarter the evaluation of D-size fluid ring sealed roller bearing assemblies was completed with the evaluation of seal configuration MT 3008 and 3016, 3016a and 3016b (different static contact seal concepts), when exposed to intensive dust and rain storms generated within an enclosure surrounding the nondriven side of test rig /number sign/3 over the entire speed range from 0 to 1220 RPM bearing test speed. During the test rig /number sign/3 shake down test runs it became apparent that the intensity of the dust and rain storms surrounding the fluid ring sealed bearing end within the ''mini'' climate chamber could be appropriately observed through small windows at 12:00 and 6:00 o'clock provided in the endwall of the ''mini-climate'' chamber, rig /number sign/3 was accordingly modified and the dust and rain exposure tests were conducted at numerous levels of severity. 6 figs.

  4. Computational fluid dynamic investigations and experimental validation of frozen seal sodium valve assembly of a fast reactor

    Energy Technology Data Exchange (ETDEWEB)

    Velusamy, K., E-mail: kvelu@igcar.gov.i [Indira Gandhi Centre for Atomic Research, Kalpakkam - 603 102 (India); Raviprasan, G.R.; Nema, Vivek; Meikandamurthy, C.; Selvaraj, P.; Chellapandi, P.; Vaidyanathan, G.; Chetal, S.C. [Indira Gandhi Centre for Atomic Research, Kalpakkam - 603 102 (India)

    2010-11-15

    Frozen seal sodium valves are used in fast reactors. To achieve sodium freezing, horizontal fins are attached to the outer surface of valve sheath. Adjacent fins form open-ended cavities and natural convection of air in these cavities is investigated using the PHOENICS code for various values of fin length, spacing and root temperature. It is seen that convective air does not penetrate deep into shallow cavities leading to poor heat transfer coefficient, offsetting the enhancement in surface area. Penetration depth of air is a function of aspect ratio and Rayleigh number based on fin spacing and is independent of fin length. Generalized correlations are derived for Nusselt number in terms of Rayleigh number and aspect ratio. Using these correlations, temperature distribution in entire valve assembly is predicted using the HEATING5 code, to select an optimum design. Experiments have been conducted on a model valve of selected design in the SILVERINA facility available at this centre. Measured stem temperature distribution is found to compare satisfactorily with HEATING5 predictions, validating the correlations derived from computational fluid dynamic studies and integrated thermal analysis methodology.

  5. Development of fluid and I and C systems design technology

    Energy Technology Data Exchange (ETDEWEB)

    Sim, Yoon Sub; Park, C. K.; Kim, S. O. [and others

    2000-05-01

    LMR is the reactor type that makes utilization of uranium resource very efficiently and the necessity of construction of a LMR in 2020's has been raised. However, the design technology required for construction has not been secured domestically. To fulfill the necessity, study has been made for the LMR system design technology and conceptual design of KALIMER systems for fluid, instrumentation, control, and protection have been developed. Also the computer code systems for the design and analysis of the KALIMER fluid systems have been developed. These study results are to used as the starting point of the next phase LMR design technology development research.

  6. Study on Synthesis of Polyacrylamide Microspheres and its Sealing Characteristics of Drilling Fluid

    Directory of Open Access Journals (Sweden)

    Mingming Cheng

    2014-02-01

    Full Text Available For the purpose of reducing the invasion depth of solid phase and liquid phase of drilling fluid and improving the quality of drilling mud cake, polyacrylamide microspheres were successfully composed via reversed phrase emulsion method. The physical and chemical structures of the samples as well as the grain-size variation were investigated by Transmission Electron Microscopy (TEM and Laser Particle Size Analysis method (LPSA.The plugging performance of the samples were investigated by core plugging experiment and sand bed filtration experiment. TEM images show that acrylamide has been polymerized, the products consist of a lot of monodisperse microspheres with a size of about 1-6 μm. LPSA images indicate that the particle size of polyacrylamide microspheres vary with time and temperature regularly. The experiment that simulates rock strata with different permeability shows those polyacrylamide microspheres can produce effectively blocked to the core and sand bed and then it establishes the foundation for the next field test.

  7. Diapirism on Venus and the Early Earth and The thermal effect of fluid flows in AECL's Tunnel Sealing Experiment

    Science.gov (United States)

    Robin, Catherine M. I.

    2010-12-01

    Flow instabilities occur at all scales in planetary systems. In this thesis we examine three cases of such instabilities, on three very different length scales. In the first part, we test the idea that Archean granite-greenstone belts (GGBs) form by crustal diapirism, or Rayleigh-Taylor instabilities. GGBs are characterized by large granitic domes (50-100 km in diameter) embedded in narrow keel-shaped greenstones. They are ubiquitous in Archean (> 2.5 Ga) terrains, but rare thereafter. We performed finite element calculations for a visco-elastic, temperature-dependent, non-Newtonian crust under conditions appropriate for the Archean, which show that dense low-viscosity volcanics overlying a felsic basement will overturn diapirically in as little as 10 Ma, displacing as much as 60 % of the volcanics to the lower crust. This surprisingly fast overturn rate suggests that diapiric overturn dominated crustal tectonics in the hot conditions of the Early Earth, becoming less important as the Earth cooled. Moreover, the deposition of large volumes of wet basaltic volcanics to the lower crust may provide the source for the formation of the distinctly Archean granitic rocks which dominate Earth's oldest continents. The second part examines the origin of Venusian coronae, circular volcanic features unique to Venus. Coronae are thought to result from small instabilities (diapirs) from the core-mantle boundary, which are typical of stagnant-lid convection. However, most young coronae are located in a region surrounded by long-lived hotspots, typical of a more active style of mantle convection. Using analogue experiments in corn syrup heated from below, we show that the co-existence of diapirs and long-lived mantle plumes are a direct consequence of the catastrophic overturn of the cold Venusian lithosphere thought to have occurred ˜ 700 Ma ago. In the last part we analyze the thermal effect of fluid flow through a full-scale experiment testing clay and concrete tunnel seals in

  8. Technology Solutions for New and Existing Homes Case Study: Field Trial of an Aerosol-Based Enclosure Sealing Technology

    Energy Technology Data Exchange (ETDEWEB)

    D. Springer and C. Harrington

    2016-05-01

    This report presents the results from several demonstrations of a new method for sealing building envelope air leaks using an aerosol sealing process developed by the Western Cooling Efficiency Center at UC Davis. The process involves pressurizing a building while applying an aerosol sealant to the interior. As air escapes through leaks in the building envelope, the aerosol particles are transported to the leaks where they collect and form a seal that blocks the leak.

  9. Building America Case Study: Apartment Compartmentalization with an Aerosol-Based Sealing Process - Queens, NY; Technology Solutions for New and Existing Homes, Energy Efficiency & Renewable Energy (EERE)

    Energy Technology Data Exchange (ETDEWEB)

    None

    2015-07-01

    Air sealing of building enclosures is a difficult and time-consuming process. Current methods in new construction require laborers to physically locate small and sometimes large holes in multiple assemblies and then manually seal each of them. The innovation demonstrated under this research study was the automated air sealing and compartmentalization of buildings through the use of an aerosolized sealant, developed by the Western Cooling Efficiency Center at University of California Davis.
    CARB sought to demonstrate this new technology application in a multifamily building in Queens, NY. The effectiveness of the sealing process was evaluated by three methods: air leakage testing of overall apartment before and after sealing, point-source testing of individual leaks, and pressure measurements in the walls of the target apartment during sealing. Aerosolized sealing was successful by several measures in this study. Many individual leaks that are labor-intensive to address separately were well sealed by the aerosol particles. In addition, many diffuse leaks that are difficult to identify and treat were also sealed. The aerosol-based sealing process resulted in an average reduction of 71% in air leakage across three apartments and an average apartment airtightness of 0.08 CFM50/SF of enclosure area.

  10. Numerical modelling of the mechanical and fluid flow properties of fault zones - Implications for fault seal analysis

    NARCIS (Netherlands)

    Heege, J.H. ter; Wassing, B.B.T.; Giger, S.B.; Clennell, M.B.

    2009-01-01

    Existing fault seal algorithms are based on fault zone composition and fault slip (e.g., shale gouge ratio), or on fault orientations within the contemporary stress field (e.g., slip tendency). In this study, we aim to develop improved fault seal algorithms that account for differences in fault zone

  11. Supercritical fluid technology for energy and environmental applications

    CERN Document Server

    Anikeev, Vladimir

    2014-01-01

    Supercritical Fluid Technology for Energy and Environmental Applications covers the fundamental principles involved in the preparation and characterization of supercritical fluids (SCFs) used in the energy production and other environmental applications. Energy production from diversified resources - including renewable materials - using clean processes can be accomplished using technologies like SCFs. This book is focused on critical issues scientists and engineers face in applying SCFs to energy production and environmental protection, the innovative solutions they have found, and the challenges they need to overcome. The book also covers the basics of sub- and supercritical fluids, like the thermodynamics of phase and chemical equilibria, mathematical modeling, and process calculations. A supercritical fluid is any substance at a temperature and pressure above its critical point where distinct liquid and gas phases do not exist. At this state the compound demonstrates unique properties, which can be "fine...

  12. Nano-micro composite magnetic fluids: Magnetic and magnetorheological evaluation for rotating seal and vibration damper applications

    Science.gov (United States)

    Marinică, Oana; Susan-Resiga, Daniela; Bălănean, Florica; Vizman, Daniel; Socoliuc, Vlad; Vékás, Ladislau

    2016-05-01

    In this paper, static magnetic properties and magnetorheological behavior of a set of 12 nano-micro composite magnetic fluids (CMFs) were studied. The samples with a ferromagnetic particle volume fraction ranging in a large interval φFe = (1 ÷ 44) % were prepared by adding carbonyl iron powder in a highly concentrated transformer oil-based ferrofluid (FF). The ferrofluid has the magnetite volume fraction of φFe3O4 = 22.90 % and saturation magnetization of Ms = 74 kA / m (930 Gs). No further additives were used in order to prevent sedimentation. It was noticed an increase of the static yield stress, of about 3 orders of magnitude, with the increase of the total solid volume fraction of samples and with the increase of the magnetic field, which varied between 0 kA/m and 950 kA/m. The dynamic yield stress (Herschel-Bulkley model) τHB of the samples strongly increases with the magnetic field and shows a slight tendency of saturation for higher intensities of the magnetic field. There is a less pronounced increase of τHB, about an order of magnitude with the increasing volume fraction of the iron particles. The relative viscosity increase induced by the magnetic field reaches a maximum for both considered shear rates: γ ṡ = 7.85s-1 and γ ṡ = 88.41s-1 and it was revealed an optimal volume fraction of Fe particles, φFe = 20 % , corresponding to a total volume fraction of φtot ≈ 38 % , at which the magnetoviscous effect has its maximum value. The magnetic properties and also the magnetorheological and the magnetoviscous behavior of highly concentrated ferrofluid-based CMFs can be controlled by the addition of iron microparticles in order to attain the optimal concentration for the envisaged engineering applications, rotating seals and magnetorheological vibration dampers.

  13. Upgrading oil sands bitumen with FLUID COKING and FLEXICOKING technologies

    Energy Technology Data Exchange (ETDEWEB)

    Kamienski, P.; Phillips, G. [ExxonMobil Research and Engineering Co., Fairfax, VA (United States); McKnight, C.; Rumball, B. [Syncrude Canada Ltd., Calgary, AB (Canada)

    2009-07-01

    This presentation described EMRE's Fluid Coking and Flexicoking technologies that are well suited for upgrading Alberta's heavy crudes and oil sands bitumen into pipelineable crudes or synthetic crudes, which can be further processed into transportation fuels. The Fluid Coking technology uses a fluidized bed reactor that thermally converts the heavy oils into light gases, liquids and coke. The metals and much of the sulphur are concentrated in the coke. Combustion of the coke provides process heat and the remaining coke is sold or stored on site for later recovery. Syncrude Canada currently operates 3 Fluid Coking units in northern Alberta. Flexicoking extends fluid coking by integrating air gasification to produce a carbon monoxide/hydrogen rich fuel gas that helps meet fuel and energy requirements of bitumen recovery and upgrading. The yields of light gas and liquids are similar to those of the Fluid Coking process. The partial combustion of coke provides the process heat for the thermal conversion and gasification steps. The remaining coke is gasified and desulphurized using Flexsorb technology. At present, there are 5 Flexicoking units in operation around the world. Interest in the technology is growing, particularly in locations with large demand for clean fuel or electricity. It is also suitable for steam assisted gravity drainage (SAGD) operations in Alberta. This presentation outlined the operating principles of the Flexicoking integrated gasification system and compared it with more expensive oxygen gasification processes. tabs., figs.

  14. Numerical, Analytical, Experimental Study of Fluid Dynamic Forces in Seals. Volume 1; Executive Summary and Description of Knowledge-Based System

    Science.gov (United States)

    Liang, Anita D. (Technical Monitor); Shapiro, Wilbur; Aggarwal, Bharat

    2004-01-01

    The objectives of the program were to develop computational fluid dynamics (CFD) codes and simpler industrial codes for analyzing and designing advanced seals for air-breathing and space propulsion engines. The CFD code SCISEAL is capable of producing full three-dimensional flow field information for a variety of cylindrical configurations. An implicit multidomain capability allows the division of complex flow domains to allow optimum use of computational cells. SCISEAL also has the unique capability to produce cross-coupled stiffness and damping coefficients for rotordynamic computations. The industrial codes consist of a series of separate stand-alone modules designed for expeditious parametric analyses and optimization of a wide variety of cylindrical and face seals. Coupled through a Knowledge-Based System (KBS) that provides a user-friendly Graphical User Interface (GUI), the industrial codes are PC based using an OS/2 operating system. These codes were designed to treat film seals where a clearance exists between the rotating and stationary components. Leakage is inhibited by surface roughness, small but stiff clearance films, and viscous pumping devices. The codes have demonstrated to be a valuable resource for seal development of future air-breathing and space propulsion engines.

  15. Sealing device and method for sealing fractures or leaks in wall or formation surrounding tube-shaped channel

    DEFF Research Database (Denmark)

    2014-01-01

    (11) arranged between the second annular flow barrier (8) and a third annular flow barrier (12) and including a sealing fluid activation device (13) adapted to at least initiate or accelerate curing of the sealing fluid (17). In operation, the elongated body may be displaced along the tube......-shaped channel until the sealing fluid activation section is placed at a position where sealing fluid has been ejected by the sealing fluid placement section, and the sealing fluid activation device may be activated. Thereby, sealing fluid may be cured at selected locations along the tube-shaped channel after...

  16. Friction Characteristics of Mechanical Seals with Laser-textured Seal Faces

    Institute of Scientific and Technical Information of China (English)

    2002-01-01

    Heat generated by friction between faces of mechanica l seals is a major factor that causes deterioration of the seals and shortens th eir service life. Excessive temperature rise can greatly alter the seal geometry and vaporize the sealing fluid, resulting in friction of boundary lubrication. These effects on face seals usually lead to excessive leakage and ultimately ren der the seal inoperable. In order to maintain the reliability of seals, high fri ction and unwanted wear must be avoided. Using the l...

  17. Integrating multiple technologies to understand the foraging behaviour of Hawaiian monk seals

    Science.gov (United States)

    Littnan, Charles; Halpin, Patrick; Read, Andrew

    2017-01-01

    The objective of this research was to investigate and describe the foraging behaviour of monk seals in the main Hawaiian Islands. Specifically, our goal was to identify a metric to classify foraging behaviour from telemetry instruments. We deployed accelerometers, seal-mounted cameras and GPS tags on six monk seals during 2012–2014 on the islands of Molokai, Kauai and Oahu. We used pitch, calculated from the accelerometer, to identify search events and thus classify foraging dives. A search event and consequent ‘foraging dive’ occurred when the pitch was greater than or equal to 70° at a depth less than or equal to −3 m. By integrating data from the accelerometers with video and GPS, we were able to ground-truth this classification method and identify environmental variables associated with each foraging dive. We used Bayesian logistic regression to identify the variables that influenced search events. Dive depth, body motion (mean overall dynamic body acceleration during the dive) and proximity to the sea floor were the best predictors of search events for these seals. Search events typically occurred on long, deep dives, with more time spent at the bottom (more than 50% bottom time). We can now identify where monk seals are foraging in the main Hawaiian Islands (MHI) and what covariates influence foraging behaviour in this region. This increased understanding will inform management strategies and supplement outreach and recovery efforts. PMID:28405358

  18. 汽轮机密封技术的应用与发展%Application and Development of Turbine Sealing Technology

    Institute of Scientific and Technical Information of China (English)

    郑数; 郁春鹏; 戴荣川; 晋圣根

    2014-01-01

    Steam seal is an important part of turbine, the main role of which is sealing, and its sealing capacity will affect leakage of the steam. Steam provides power for turbine, so its sealing performance will directly affect the obtained energy of turbine. This article discusses turbine sealing technology.%在汽轮机上有个很重要的部件就是汽封,汽封主要起到密封的作用,其密封能力的好坏影响到蒸汽是否泄露,而蒸汽为汽轮机提供动力,因此其密封性能的高低会影响到汽轮机获得动能的大小。本篇文章就是对汽轮机的密封技术进行探讨。

  19. Rim seal arrangement having pumping feature

    Energy Technology Data Exchange (ETDEWEB)

    Lee, Ching-Pang; Myers, Caleb

    2017-04-25

    A rim seal arrangement for a gas turbine engine includes a first seal face on a rotor component, and a second seal face on a stationary annular rim centered about a rotation axis of the rotor component. The second seal face is spaced from the first seal face along an axial direction to define a seal gap. The seal gap is located between a radially outer hot gas path and a radially inner rotor cavity. The first seal face has a plurality of circumferentially spaced depressions, each having a depth in an axial direction and extending along a radial extent of the first seal face. The depressions influence flow in the seal gap such that during rotation of the rotor component, fluid in the seal gap is pumped in a radially outward direction to prevent ingestion of a gas path fluid from the hot gas path into the rotor cavity.

  20. [Research on soil bacteria under the impact of sealed CO2 leakage by high-throughput sequencing technology].

    Science.gov (United States)

    Tian, Di; Ma, Xin; Li, Yu-E; Zha, Liang-Song; Wu, Yang; Zou, Xiao-Xia; Liu, Shuang

    2013-10-01

    Carbon dioxide Capture and Storage has provided a new option for mitigating global anthropogenic CO2 emission with its unique advantages. However, there is a risk of the sealed CO2 leakage, bringing a serious threat to the ecology system. It is widely known that soil microorganisms are closely related to soil health, while the study on the impact of sequestered CO2 leakage on soil microorganisms is quite deficient. In this study, the leakage scenarios of sealed CO2 were constructed and the 16S rRNA genes of soil bacteria were sequenced by Illumina high-throughput sequencing technology on Miseq platform, and related biological analysis was conducted to explore the changes of soil bacterial abundance, diversity and structure. There were 486,645 reads for 43,017 OTUs of 15 soil samples and the results of biological analysis showed that there were differences in the abundance, diversity and community structure of soil bacterial community under different CO, leakage scenarios while the abundance and diversity of the bacterial community declined with the amplification of CO2 leakage quantity and leakage time, and some bacteria species became the dominant bacteria species in the bacteria community, therefore the increase of Acidobacteria species would be a biological indicator for the impact of sealed CO2 leakage on soil ecology system.

  1. Building America Best Practices Series, Volume 10: Retrofit Techniques and Technologies: Air Sealing

    Energy Technology Data Exchange (ETDEWEB)

    Baechler, Michael C.; Gilbride, Theresa L.; Hefty, Marye G.; Cole, Pamala C.; Williamson, Jennifer L.; Love, Pat M.

    2010-04-12

    This report was prepared by PNNL for the U.S. Department of Energy Building America Program. The report provides information to home owners who want to make their existing homes more energy efficient by sealing leaks in the building envelope (ceiling, walls, and floors) that let in drafts and let conditioned air escape. The report provides descriptions of 19 key areas of the home where air sealing can improve home performance and energy efficiency. The report includes suggestions on how to find a qualified weatherization or home performance contractor, what to expect in a home energy audit, opportune times for performing air sealing, and what safety and health concerns to be aware of. The report describes some basic building science concepts and topics related to air sealing including ventilation, diagnostic tools, and code requirements. The report will be available for free download from the DOE Building America website. It is a suitable consumer education tool for home performance and weatherization contractors to share with customers to describe the process and value of home energy retrofits.

  2. The Review of Test Technology for the Ameriacan High Temperature Structural Seals%美国高温密封试验技术研究

    Institute of Scientific and Technical Information of China (English)

    张婕; 蒋军亮; 任青梅; 李玺

    2015-01-01

    高温密封是高超音速飞行器的关键技术.文章详细介绍了美国关于热密封结构所开展的试验技术研究,包括压力试验、热暴露试验、热摩擦试验、泄漏试验的试验方法和试验设备.%High temperature structural seals have been identified as a critical technology in the development of space-earth shuttle. Perfor-mance criteria and design criteria for high temperature Seals were introduced in this paper. A series of thermal/strengthen performance test technology and facility for the high temperature structural seals such as pressure tests, leak test, temperature exposure test, scrub test were discussed. It can be helpful for the development of seal test for us.

  3. CNP1000轴封式核主泵技术%Technology for CNP1000 shaft sealed reactor coolant pump

    Institute of Scientific and Technical Information of China (English)

    冯晓东; 吴大转; 杨立峰; 贾允

    2016-01-01

    CNP1000轴封式核主泵作为泵类行业的高端设备是核电站一回路系统中唯一没有实现国产化的设备,其自主设计、制造及试验是中国推进核电自主化的重点和难点。对核电泵的国内技术现状以及1000 MW轴封式核主泵结构特点进行了介绍,分别从承压边界、水力部件、转子轴系、隔热组件、轴密封、停车密封、水导轴承、推力轴承、一体化供油泵、油密封、辅助系统及其关键设备进行了设计原理和实施要求的详细说明。通过对不同类型主泵的出口限制情况和应用前景比较分析,说明了轴封主泵对外出口的优势,提出轴封主泵将在很长一段时间占据核电市场的主导地位。目前国内企业已完成了多项关键技术,如主轴密封、水力部件、全流量试验等的自主化,但是核主泵的理论基础并没有完整建立,有待进一步研究。因此,核主泵的国产化研制任务仍需较长的时间去攻克。%As high-end equipment in pump industry , CNP1000 shaft sealed reactor coolant pump ( RCP) in the primary loop system of pressurized water reactor ( PWR) in a nuclear power plant is the only equipment which cannot be manufactured domestically .Therefore, the independent design , ma-nufacturing and test of this kind of pump are important and difficult tasks in promoting the nationaliza-tion of nuclear technology in China .The domestic technological situation and structural characteristics of 1 000 MW shaft sealed RCP are introduced , and the design principle and technical implementation requirement are elaborated in terms of pressure retaining boundary , hydraulic components , pump rotor system, heat insulation subassembly , shaft seal, standstill seal, lower guide bearings, thrust bearing, integrated oil pump , oil seal, auxiliary system and key equipment in detail .Through an analysis on ex-port restriction and application prospect of various types of RCP , it is

  4. Fluid Bed Technology: Overview and Parameters for Process Selection

    OpenAIRE

    Saurabh Srivastava; Garima Mishra

    2010-01-01

    Formulation development is the most emerging and upcoming face of pharmaceutical technology in the current era. It is contemporarily capturing the market leaps and bounds with recent trends and developments with its innovative techniques. The day-to-day advancements in the research have provided an edge to this brilliant branch of pharmaceutical sector for not only uplifting the pharmacy profession but also to conquer the diseased state for nurturing the health and humanity. The fluid-bed tec...

  5. Evaluation of the quality of the apical seal in Resilon/Epiphany and Gutta-Percha/AH Plus-filled root canals by using a fluid filtration approach.

    Science.gov (United States)

    Raina, Rakesh; Loushine, Robert J; Weller, R Norman; Tay, Franklin R; Pashley, David H

    2007-08-01

    This in vitro fluid filtration study compared the apical leakage of root canals that were obturated with Resilon/Epiphany (Resilon Research LLC, Madison, CT) or gutta-percha/AH Plus (GP/AH; DENTSPLY Tulsa, Tulsa, OK) sealer using warm vertical condensation. Fluid flow rate through the filled roots was measured 7 days after the obturations by using a fluid filtration device. Measurements were made before root resection and after 3 to 11 mm of resections. Before any removal of root length, there were no significant differences between the roots filled with Resilon/Epiphany or GP/AH. Analysis of individual root resection results revealed that differences in the fluid flow rate of the two systems occurred only when 9 or 10 mm of the roots were resected with more than half the root length resected when GP/AH Plus leaked more than Resilon/Epiphany. There were no significant differences in the fluid flow rate up to and including 8 mm of root resection. It is concluded Resilon/Epiphany sealed 17-mm root canals as well as gutta-percha and AH Plus sealer and that it does not create a monoblock root filling that does not leak.

  6. Annular Pressure Seals and Hydrostatic Bearings

    Science.gov (United States)

    2006-11-01

    affecting the rotordynamics of liquid turbopumps, in particular those handling large density fluids. Highlights on the bulk-flow analysis of annular seals... rotordynamic stability. Hydrostatic bearings rely on external fluid pressurization to generate load support and large centering stiffnesses, even in...SEALS IN PUMP APPLICATIONS Seal rotordynamic characteristic have a primary influence on the stability response of high-performance turbomachinery [1

  7. New pollution reduction technologies through tank sealing of slag and ashes pits

    Energy Technology Data Exchange (ETDEWEB)

    Bruell, A.; Revenco, V. [Institutul de Stuidii Si Proiectari Energetice S.A. (ISPE), Bucharest (Hungary)

    2002-07-01

    Under the Romanian environment protection law provision no. 137/1995, the existing slag and ashes pits raise problems due to the exfiltrations from the pits tank towards the phreatic water sheet. The design includes the following steps to be taken: pit bed waterproofing under new works; bed ends sealing, parallel with pit aggradation for dumps in operation; waterproofing of aggradation dikes. The conventional solution is clay plating. When works are performed under bad weather conditions, and clay must be brought from remote distances, the clay plating solution should be compared to the geocomponents one. The latter area combination of geotextiles and bentone material that can be placed easily, joint in situ, and can be paid at negative temperatures. Once wet, geo components become impermeable. The paper describes the sealing performed at the slag and ashes pit of Vales Ceplea at Turceni thermal power plant, and the sealing solution being developed at the Beterega Nord slag and ashes pit at Rovinari thermal power plant. The necessary geophysical characteristics of the material are pointed out.

  8. 水下井口系统密封技术研究和发展现状%Review on Subsea Well System Sealing Technology Research

    Institute of Scientific and Technical Information of China (English)

    侯超; 肖文生; 刘健; 刘忠砚

    2015-01-01

    According to the characteristics of marine oil and gas,the main sealing devices used in the subsea wellhead system were summarized,current situation procession of the development of sealing technology and device of subsea well system were introduced.The difference between subsea well system seal and conventional seal was analyzed,the key tech-nology of sealing used in subsea well system was summarized.It is concluded that the main trend of subsea well system sealing depended on the marine oil and gas development in the future is metal sealing,and is pointed out that the formula-tion of relevant industry standards will promote the development of underwater sealing technology.%针对海洋油气开发特点,总结了水下井口系统用主要密封装置,介绍水下井口系统密封技术及装置发展现状,分析水下井口系统密封区别于常规密封的特点,总结水下井口系统密封的关键技术,得出海洋油气发展方向决定了金属密封技术是水下井口系统密封未来发展的主要趋势的结论,并指出相关行业标准的制订将推动水下密封技术的发展。

  9. Industrial applications and current trends in supercritical fluid technologies

    Directory of Open Access Journals (Sweden)

    Gamse Thomas

    2005-01-01

    Full Text Available Supercritical fluids have a great potential for wide fields of processes Although CO2 is still one of the most used supercritical gases, for special purposes propane or even fluorinated-chlorinated fluids have also been tested. The specific characteristics of supercritical fluids behaviour were analyzed such as for example the solubilities of different components and the phase equilibria between the solute and solvent. The application at industrial scale (decaffeinating of tea and coffee, hop extraction or removal of pesticides from rice, activity in supercritical extraction producing total extract from the raw material or different fractions by using the fractionated separation of beverages (rum, cognac, whisky, wine, beer cider, of citrus oils and of lipids (fish oils, tall oil were also discussed. The main interest is still for the extraction of natural raw materials producing food ingredients, nutraceuticals and phytopharmaceuticals but also cleaning purposes were tested such as the decontamination of soils the removal of residual solvents from pharmaceutical products, the extraction of flame retardants from electronic waste or precision degreasing and cleaning of mechanical and electronic parts. An increasing interest obviously exists for impregnation purposes based on supercritical fluids behaviour, as well as for the dying of fibres and textiles. The production of fine particles in the micron and submicron range, mainly for pharmaceutical products is another important application of supercritical fluids. Completely new products can be produced which is not possible under normal conditions. Supercritical fluid technology has always had to compete with the widespread opinion that these processes are very expensive due to very high investment costs in comparison with classical low-pressure equipment. Thus the opinion is that these processes should be restricted to high-added value products. A cost estimation for different plant sizes and

  10. Mass transport of heavy metal ions and radon in gels used as sealing agents in containment technologies

    Energy Technology Data Exchange (ETDEWEB)

    Lakatos, I.; Bauer, K.; Lakatos-Szabo, J. [Research Lab. for Mining Chemistry, Miskolc-Egyetemvaros (Hungary); Kretzschmar, H.J. [DBI Gas- und Umwelttechnik GmbH, Feiberg (Germany)

    1997-12-31

    The diffusion and hydrodynamic mass transport of multivalent cations, mostly Cr(III) and Cr(VI) ions and radon in polymer/silicate gels and Montanwax emulsions were studied. It was concluded that the self-conforming gels may decrease the hydrodynamic mass transport in porous and fractured media by 4-6 orders of magnitude. In water saturated systems, however, the diffusion transport can be restricted by hydrogels only to a moderate extent. On the other hand, the high and selective retention capacity of gels towards different diffusing species may open new vistas in the sealing technologies. Similar results were obtained for transport phenomena of radon. The almost perfect quenching process of radon and its nuclides in gels and emulsions further enhances the positive effects of the encapsulation methods. The laboratory experiments provided valuable new information to design the different containment technologies.

  11. Mechanical seals

    CERN Document Server

    Mayer, E

    1977-01-01

    Mechanical Seals, Third Edition is a source of practical information on the design and use of mechanical seals. Topics range from design fundamentals and test rigs to leakage, wear, friction and power, reliability, and special designs. This text is comprised of nine chapters; the first of which gives a general overview of seals, including various types of seals and their applications. Attention then turns to the fundamentals of seal design, with emphasis on six requirements that must be considered: sealing effectiveness, length of life, reliability, power consumption, space requirements, and c

  12. Computational Fluid Dynamics (CFD) Technology Programme 1995- 1999

    Energy Technology Data Exchange (ETDEWEB)

    Haekkinen, R.J.; Hirsch, C.; Krause, E.; Kytoemaa, H.K. [eds.

    1997-12-31

    The report is a mid-term evaluation of the Computational Fluid Dynamics (CFD) Technology Programme started by Technology Development Centre Finland (TEKES) in 1995 as a five-year initiative to be concluded in 1999. The main goal of the programme is to increase the know-how and application of CFD in Finnish industry, to coordinate and thus provide a better basis for co-operation between national CFD activities and encouraging research laboratories and industry to establish co-operation with the international CFD community. The projects of the programme focus on the following areas: (1) studies of modeling the physics and dynamics of the behaviour of fluid material, (2) expressing the physical models in a numerical mode and developing a computer codes, (3) evaluating and testing current physical models and developing new ones, (4) developing new numerical algorithms, solvers, and pre- and post-processing software, and (5) applying the new computational tools to problems relevant to their ultimate industrial use. The report consists of two sections. The first considers issues concerning the whole programme and the second reviews each project

  13. Fluid Mechanics of Biological Surfaces and their Technological Application

    Science.gov (United States)

    Bechert, D. W.; Bruse, M.; Hage, W.; Meyer, R.

    A survey is given on fluid-dynamic effects caused by the structure and properties of biological surfaces. It is demonstrated that the results of investigations aiming at technological applications can also provide insights into biophysical phenomena. Techniques are described both for reducing wall shear stresses and for controlling boundary-layer separation. (a) Wall shear stress reduction was investigated experimentally for various riblet surfaces including a shark skin replica. The latter consists of 800 plastic model scales with compliant anchoring. Hairy surfaces are also considered, and surfaces in which the no-slip condition is modified. Self-cleaning surfaces such as that of lotus leaves represent an interesting option to avoid fluid-dynamic deterioration by the agglomeration of dirt. An example of technological implementation is discussed for riblets in long-range commercial aircraft. (b) Separation control is also an important issue in biology. After a few brief comments on vortex generators, the mechanism of separation control by bird feathers is described in detail. Self-activated movable flaps (=artificial bird feathers) represent a high-lift system enhancing the maximum lift of airfoils by about 20%. This is achieved without perceivable deleterious effects under cruise conditions. Finally, flight experiments on an aircraft with laminar wing and movable flaps are presented.

  14. Advanced CO2 Leakage Mitigation using Engineered Biomineralization Sealing Technologies

    Energy Technology Data Exchange (ETDEWEB)

    Spangler, Lee [Montana State Univ., Bozeman, MT (United States); Cunningham, Alfred [Montana State Univ., Bozeman, MT (United States); Phillips, Adrienne [Montana State Univ., Bozeman, MT (United States)

    2015-03-31

    This research project addresses one of the goals of the DOE Carbon Sequestration Program (CSP). The CSP core R&D effort is driven by technology and is accomplished through laboratory and pilot scale research aimed at new technologies for greenhouse gas mitigation. Accordingly, this project was directed at developing novel technologies for mitigating unwanted upward leakage of carbon dioxide (CO2) injected into the subsurface as part of carbon capture and storage (CCS) activities. The technology developed by way of this research project is referred to as microbially induced calcite precipitation (MICP).

  15. Supercritical fluids technology in bioprocess industries: A review

    Directory of Open Access Journals (Sweden)

    Kianoush Khosravi Darani

    2009-12-01

    Full Text Available This article reviews the fundamentals of supercritical fluid (SCF science and moves on to the biotechnological applications of them e.g. removal of biostatic agents from fermentation broths, SCF disruption of microorganisms, destruction of industrial waste, the gas-antisolvent crystallization and micron-size particle formation. Also gaining ground is enzymatic catalysis in supercritical carbon dioxide (SC-CO2, which offers the possibility of integrated synthesis product recovery processes. The paper is structured as follows: first, the effects of dense SC-CO2 on the extraction of biomaterials and disruption of cells are thoroughly reported and discussed. Then the application of SC-CO2 in particle formation and modifications of biopolymers and enzymes are described. In general, the article is focused on potential bio-industrial applications and future research needs of the SCF technology. Keywords: Biotechnology, Supercritical Fluids (SCF, disruption, inactivation, extraction, downstream, particle formation Received: 10 October 2009 / Received in revised form: 30 January 2010, Accepted: 30 January 2010, Published online: 10 March 2010

  16. Non-contacting fluid ring seal systems for railcar axle bearing systems: Quarterly progress report No. 3, December 16, 1987-March 15, 1988

    Energy Technology Data Exchange (ETDEWEB)

    1988-01-01

    One test rig was completed, and a FR seal prototype test was initiated. No leaks of grease were detected. A used ''D'' sized lip seal was evaluated. New FR seals are being designed. 6 figs. (DLC)

  17. Drilling Fluid System & Technology in Sichuan Gas Field

    Institute of Scientific and Technical Information of China (English)

    Wang You; He Lun

    1995-01-01

    @@ Polymer Drilling FluidSystem SPA (Sichuan Petroleum Administration) began to use non-dispersed polymer drilling fluids in 1975. In the beginning,SPA adopted the single polymer drilling fluid systems utilizing single polyacrylamide as full flocculants or utilizing PHPA (partially hydrolyzed polyacrylamide) as proper flocculants, then SPA widely popularized the multi-polymer drilling fluid systems compounding of high, medium and low molecular weight polymers. The amphoteric polymers drilling fluid has been successfully developed and applied in recent years.

  18. Reducing blood loss in total joint surgery with a saline-coupled bipolar sealing technology.

    Science.gov (United States)

    Rosenberg, Aaron G

    2007-06-01

    Despite the availability of a number of techniques to reduce blood loss in patients undergoing total joint arthroplasty, many patients remain at risk of receiving blood transfusions postoperatively. We have used a new technology that couples bipolar radiofrequency energy with saline to reduce blood loss in patients undergoing total joint surgery. The use of this technology has been shown to effectively minimize the risk of transfusion and reduce intraoperative and postoperative bleeding-related complications.

  19. Navy GTE seal development activity

    Science.gov (United States)

    Grala, Carl P.

    1993-10-01

    Under the auspices of the Integrated High Performance Turbine Engine Technology Initiative, the Naval Air Warfare Center conducts advanced development programs for demonstration in the next generation of air-breathing propulsion systems. Among the target technologies are gas path and lube oil seals. Two development efforts currently being managed by NAWCAD are the High Performance Compressor Discharge Film-Riding Face Seal and the Subsonic Core High Speed Air/Oil Seal. The High Performance Compressor Discharge Film-Riding Face Seal Program aims at reducing parasitic leakage through application of a film-riding face sea concept to the compressor discharge location of a Phase 2 IHPTET engine. An order-of-magnitude leakage reduction relative to current labyrinth seal configurations is expected. Performance goals for these seals are (1) 1200 F air temperature, (2) 800 feet-per-second surface velocity, and (3) 600 SPI differential pressure. The two designs chosen for fabrication and rig test are a spiral groove and a Rayleigh step seal. Rig testing is currently underway. The Subsonic Core High Speed Air/Oil Seal Program is developing shaft-to-ground seals for next-generation propulsion systems that will minimize leakage and provide full life. Significantly higher rotor speeds and temperatures will be experienced. Technologies being exploited include, hydrodynamic lift assist features, ultra light weight designs, and improved cooling schemes. Parametric testing has been completed; a final seal design is entering the endurance test phase.

  20. Aerodynamic seals for rotary machine

    Energy Technology Data Exchange (ETDEWEB)

    Bidkar, Rahul Anil; Cirri, Massimiliano; Thatte, Azam Mihir; Williams, John Robert

    2016-02-09

    An aerodynamic seal assembly for a rotary machine includes multiple sealing device segments disposed circumferentially intermediate to a stationary housing and a rotor. Each of the segments includes a shoe plate with a forward-shoe section and an aft-shoe section having multiple labyrinth teeth therebetween facing the rotor. The sealing device segment also includes multiple flexures connected to the shoe plate and to a top interface element, wherein the multiple flexures are configured to allow the high pressure fluid to occupy a forward cavity and the low pressure fluid to occupy an aft cavity. Further, the sealing device segments include a secondary seal attached to the top interface element at one first end and positioned about the flexures and the shoe plate at one second end.

  1. Cryogenic Fluid Management Technology and Nuclear Thermal Propulsion

    Science.gov (United States)

    Taylor, Brian D.; Caffrey, Jarvis; Hedayat, Ali; Stephens, Jonathan; Polsgrove, Robert

    2016-01-01

    Cryogenic fluid management (CFM) is critical to the success of future nuclear thermal propulsion powered vehicles. While this is an issue for any propulsion system utilizing cryogenic propellants, this is made more challenging by the radiation flux produced by the reactor in a nuclear thermal rocket (NTR). Managing the cryogenic fuel to prevent propellant loss to boil off and leakage is needed to limit the required quantity of propellant to a reasonable level. Analysis shows deposition of energy into liquid hydrogen fuel tanks in the vicinity of the nuclear thermal engine. This is on top of ambient environment sources of heat. Investments in cryogenic/thermal management systems (some of which are ongoing at various organizations) are needed in parallel to nuclear thermal engine development in order to one day see the successful operation of an entire stage. High durability, low thermal conductivity insulation is one developmental need. Light weight cryocoolers capable of removing heat from large fluid volumes at temperatures as low as approx. 20 K are needed to remove heat leak from the propellant of an NTR. Valve leakage is an additional CFM issue of great importance. Leakage rates of state of the art, launch vehicle size valves (which is approximately the size valves needed for a Mars transfer vehicle) are quite high and would result in large quantities of lost propellant over a long duration mission. Additionally, the liquid acquisition system inside the propellant tank must deliver properly conditioned propellant to the feed line for successful engine operation and avoid intake of warm or gaseous propellant. Analysis of the thermal environment and the CFM technology development are discussed in the accompanying presentation.

  2. NASA Lewis Research Center low-gravity fluid management technology program

    Science.gov (United States)

    Aydelott, J. C.; Carney, M. J.; Hochstein, J. I.

    1985-01-01

    A history of the Lewis Research Center in space fluid management technology program is presented. Current programs which include numerical modeling of fluid systems, heat exchanger/radiator concept studies, and the design of the Cryogenic Fluid Management Facility are discussed. Recent analytical and experimental activities performed to support the Shuttle/Centaur development activity are highlighted.

  3. Sealing coupling. [LMFBR

    Science.gov (United States)

    Pardini, J.A.; Brubaker, R.C.; Rusnak, J.J.

    1982-09-20

    Disclosed is a remotely operable releasable sealing coupling which provides fluid-tight joinder of upper and a lower conduit sections. Each conduit section has a concave conical sealing surface adjacent its end portion. A tubular sleeve having convex spherical ends is inserted between the conduit ends to form line contact with the concave conical end portions. An inwardly projecting lip located at one end of the sleeve cooperates with a retaining collar formed on the upper pipe end to provide swivel capture for the sleeve. The upper conduit section also includes a tapered lower end portion which engages the inside surface of the sleeve to limit misalignment of the connected conduit sections.

  4. Ferrules seals

    Science.gov (United States)

    Smith, J.L.

    1984-07-10

    A device is provided for sealing an inner tube and an outer tube without excessively deforming the tubes. The device includes two ferrules which cooperate to form a vacuum-tight seal between the inner tube and outer tube and having mating surfaces such that overtightening is not possible. 3 figs.

  5. Chinese Seal Clasp–Meeting technology and elegance with functional goals

    Directory of Open Access Journals (Sweden)

    Kong Mario

    2016-01-01

    Full Text Available This study comes within the framework of a PhD course in Design, which is the continuation of a Masters degree research in Fashion Design, searching for wardrobe technology and innovation, through the use of three-dimensional computer-aided design and printing, with it’s use already popular in areas related to product development and design, as well as architecture, translating and adapting, integrating it into the world of Fashion. The intent of this project is to present solutions that promote a new and versatile product, allowing for a different kind of aesthetic. This will be achieved and presented through planning and prototyping, thus creating a new clasp for fashion products. This research will result in a finished clasp, with its purpose and function being tested, in order to achieve concrete results, thus creating an innovative technology to be part of a fashion collection that allows the transformation of the suntan marks left by female swimwear. This will result in the creation of designs and drawings on the body, using shapes inspired by the Oriental Zodiac Signs, as well as colours drawn from the five elements of Feng Shui, which are also present in the Western Astrological Signs.

  6. Industrial applications and current trends in supercritical fluid technologies

    OpenAIRE

    Gamse Thomas

    2005-01-01

    Supercritical fluids have a great potential for wide fields of processes Although CO2 is still one of the most used supercritical gases, for special purposes propane or even fluorinated-chlorinated fluids have also been tested. The specific characteristics of supercritical fluids behaviour were analyzed such as for example the solubilities of different components and the phase equilibria between the solute and solvent. The application at industrial scale (decaffeinating of tea and coffee, hop...

  7. Tags and seals to strengthen arms control verification

    Energy Technology Data Exchange (ETDEWEB)

    DeVolpi, A.

    1990-10-03

    Tags and seals have long been recognized as important tools in arms control. The trend in control of armaments is to limit militarily significant equipment that is capable of being verified through direct and cooperative means, chiefly on-site inspection or monitoring. Although this paper will focus on the CFE treaty, the role of tags and seals for other treaties will also be addressed. Published technology and concepts will be reviewed, based on open sources. Arms control verification tags are defined as unique identifiers designed to be tamper-revealing; in that respect, seals are similar, being used as indicators of unauthorized access. Tamper-revealing tags are intended as single-point markers, seals for two-point couplings, and nets for volume containment. Seals usually bind two separate components, such as a hatch or flange that provides access to a secure compartment or a valve that controls fluid flow. A tamper-revealing net might be comprised of a coupled fiberoptic bundle wrapped around an object. Sometimes the term ``seal`` is used to denote the tamper-revealing feature of a tag that is attached to a surface, but in this paper the tamper-indicating connection is considered to be part of the tag concept itself.

  8. Seal Counts

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — Database of seal counts from aerial photography. Counts by image, site, species, and date are stored in the database along with information on entanglements and...

  9. Seal device for ferromagnetic containers

    Science.gov (United States)

    Meyer, Ross E.; Jason, Andrew J.

    1994-01-01

    A temporary seal or patch assembly prevents the escape of contents, e.g., fluids and the like, from within a container having a breach therethrough until the contents can be removed and/or a repair effected. A frame that supports a sealing bladder can be positioned over the breach and the frame is then attached to the container surface, which must be of a ferromagnet material, by using switchable permanent magnets. The permanent magnets are designed to have a first condition that is not attracted to the ferromagnetic surface and a second conditions whereby the magnets are attracted to the surface with sufficient force to support the seal assembly on the surface. Latching devices may be attached to the frame and engage the container surface with hardened pins to prevent the lateral movement of the seal assembly along the container surface from external forces such as fluid drag or gravity.

  10. Four Sided Seal Tester

    Science.gov (United States)

    2009-07-01

    The Center for Advanced Food Technology School of Enviromental and Biological Sciences New Brunswick, NJ 08903 FTR 216 Defense Logistics Agency...specification for four sided seal tester as function of confinement plate distance” The following modifications were issued :  Jul 18, 2007 0013/01

  11. New-Generation Sealing Slurries For Borehole Injection Purposes

    Science.gov (United States)

    Stryczek, Stanisław; Gonet, Andrzej; Wiśniowski, Rafał; Złotkowski, Albert

    2015-12-01

    The development of techniques and technologies thanks to which parameters of the ground medium can be modified makes specialists look for new recipes of geopolymers - binders for the reinforcing and sealing of unstable and permeable grounds. The sealing slurries are expected to meet a number of strict requirements, therefore it is important to find new admixtures and additives which could modify the fresh and hardened slurry. Special attention has been recently paid to the fluid ash - a by-product of the combustion of hard coals. However, the use of this additive is associated with the application of appropriate superplastifier. Laboratory analyses of rheological parameters of fresh sealing slurries and the ways of improving their liquidity by a properly selected third-generation superplastifier are presented in the paper. The slurries were based on Portland cement CEM I, milled granulated large-furnace slag and fly ash from fluidized-bed combustion of hard coal.

  12. A CubeSat-Scale Testbed for Cryogenic Fluid Management Technologies Project

    Data.gov (United States)

    National Aeronautics and Space Administration — NASA has identified in-space cryogenic fluid management (CFM) as a high priority for technology development because the construction of an in-space propellant...

  13. 聚合物抗渗再生涂料雾封层技术应用%Application of polymer anti-permeability regeneration coating fog seal technology

    Institute of Scientific and Technical Information of China (English)

    秦进远; 丁占锋

    2015-01-01

    基于高低温性能采用SBR和聚烯烃等对基质沥青进行复合改性研制了一种新型聚合物抗渗再生涂料,通过试验段的应用介绍了聚合物抗渗再生涂料雾封层技术,并对雾封前后路面性能指标进行了对比,结果表明:采用该技术雾封后路面抗渗水性能得到了显著提高,同时其抗滑性能满足现行规范要求。%It developed a new type of polymer anti-permeability regeneration coating using SBR and polyolefin composite modification of matrix asphalt based on the high and low temperature performances. Through the application of test section introduced the polymer anti-permeability regeneration coating fog seal technology. It compared the surface performance indexes before and after the fog seal. Results showed that pavement skid resistance performance met the current specification requirements after the fog seal,and improved the anti-permeability of pavement largely.

  14. SUPERCRITICAL FLUID TECHNOLOGY: NASCENT CONTRIVANCE FOR PHARMACEUTICAL PRODUCT DEVELOPMENT

    Directory of Open Access Journals (Sweden)

    B.S. Wakure*, A.V. Yadav , N.M. Bhatia and M.A. Salunke

    2012-07-01

    Full Text Available A supercritical fluid (SF can be defined as a dense non condensable fluid. A fluid reaches the supercritical status when its temperature and pressure exceed the relevant critical temperature and pressure. At the critical point only a single phase exists which has some properties typical of liquids (density and some of gases (viscosity, compressibility, and mass diffusion coefficient. For pharmaceutical applications, the most widely used SF is carbon dioxide (more than 98% of the applications have been developed using this fluid because of its low and easily accessible critical temperature (31.2◦C and pressure (7.4MPa, non-flammability, non-toxicity and inexpensiveness. The physical and thermal properties of SCFs fall between those of the pure liquid and gas. SCFs offer liquid-like densities, gas-like viscosities, gas-like compressibility properties and higher diffusivities than liquids. The properties of SCFs, such as polarity, viscosity, and diffusivity, can be altered several-fold by varying the operating temperature and/or pressure during the process. This flexibility is enabling the use of SCFs for various applications in the food and pharmaceutical industries, with the drug delivery system design being a more recent addition.

  15. Critical fluid technology for the processing of lipid-related natural products

    Energy Technology Data Exchange (ETDEWEB)

    King, J.W. [Los Alamos National Lab., Supercritical Fluid Facility, Chemistry Div. NM (United States)

    2004-07-01

    In recent years, the technology envelope that embraces critical fluids can involve a wide range of conditions, different types of pure and modified fluids, as well as processing options involving extractions, fractionations or reactions. Technological development drivers continue to be environmentally and consumer-benign processing and/or products, however in recent years expansion of the use of sub- and supercritical fluids has been catalyzed by applications in such opportune fields as nutraceuticals, conversion of biomass (bio-refining), and the ability to modify natural products by reactions. The use of critical fluid technology is an important facet of any sustainable development program, particularly when utilized over a broad, interconnected application platform. In this overview presentation, concepts and applications of critical fluids from the author's research as well as the literature will be cited to support the above trends. A totally 'green' processing platform appears to be viable using carbon dioxide in the appropriate form, ethanol and water as intermediate co-solvents/reactants, and water from above its boiling point to supercritical conditions. These fluids can be combined in overall coupled unit processes, such as combining trans-esterification with hydrogenation, or glycero-lysis of lipid moieties with supercritical fluid fractionation. Such fluids also can exploited sequentially for bio-refining processes or the segregation of value-added products, but may require using coupled fluid or unit operations to obtain the targeted product composition or purity. Changing the reduced temperatures and/or pressures of critical fluids offers a plethora of opportunity, an excellent example being the relative critical fluid state of water. For example, sub-critical water slightly above its boiling point provides a unique medium that mimics polar organic solvents, and has been used even for the extraction of thermally labile solutes or

  16. Advanced helium purge seals for Liquid Oxygen (LOX) turbopumps

    Science.gov (United States)

    Shapiro, Wilbur; Lee, Chester C.

    1989-01-01

    Program objectives were to determine three advanced configurations of helium buffer seals capable of providing improved performance in a space shuttle main engine (SSME), high-pressure liquid oxygen (LOX) turbopump environment, and to provide NASA with the analytical tools to determine performance of a variety of seal configurations. The three seal designs included solid-ring fluid-film seals often referred to as floating ring seals, back-to-back fluid-film face seals, and a circumferential sectored seal that incorporated inherent clearance adjustment capabilities. Of the three seals designed, the sectored seal is favored because the self-adjusting clearance features accommodate the variations in clearance that will occur because of thermal and centrifugal distortions without compromising performance. Moreover, leakage can be contained well below the maximum target values; minimizing leakage is important on the SSME since helium is provided by an external tank. A reduction in tank size translates to an increase in payload that can be carried on board the shuttle. The computer codes supplied under this program included a code for analyzing a variety of gas-lubricated, floating ring, and sector seals; a code for analyzing gas-lubricated face seals; a code for optimizing and analyzing gas-lubricated spiral-groove face seals; and a code for determining fluid-film face seal response to runner excitations in as many as five degrees of freedom. These codes proved invaluable for optimizing designs and estimating final performance of the seals described.

  17. Cryogenic Fluid Management Technology Workshop. Volume 1: Presentation material and discussion

    Science.gov (United States)

    Aydelott, John C. (Editor); Devol, William (Editor)

    1987-01-01

    The major objective of the workshop was to identify future NASA needs for technology that will allow the management of subcritical cryogenic fluids in the low gravity space environment. Workshop participants were asked to identify those technologies which will require in-space experimentation and are thus candidates for inclusion in the flight experiment being defined at the Lewis Research Center.

  18. 提高唇形油封寿命的装配新工艺开发%New assembly technology development on increase of lip-shaped oil seal life

    Institute of Scientific and Technical Information of China (English)

    孙丽英; 张宏伟

    2011-01-01

    Various shafts surface treatment were adopted,and the seal abrasive experiments were carried on fitting with the lip-shaped oil seal,so the shaft surface treatment technology was obtained with good seal,little abrasion and long service life.The assembly technology was analyzed and tested on the oil seal quality and the lifespan effect,and three-dimension Pro/e assembly technology was obtained,which could better ensure the oil seal assembly quality and remarkably increase the lip-shaped oil seal life and airtight performance.%采用多种轴表面处理方式,并与唇形油封进行配合密封磨损试验,得到一种密封良好、磨损小、使用寿命长的轴表面处理工艺;就装配工艺对油封质量及寿命的影响进行了分析及试验,得出采用三维Pro/e装配工艺可更好地保证油封的装配质量,显著提高唇形油封的寿命及密封性能。

  19. Python fiber optic seal

    Energy Technology Data Exchange (ETDEWEB)

    Ystesund, K.; Bartberger, J.; Brusseau, C.; Fleming, P.; Insch, K.; Tolk, K.

    1993-08-01

    Sandia National Laboratories has developed a high security fiber optic seal that incorporates tamper resistance features that are not available in commercial fiber optic seals. The Python Seal is a passive fiber optic loop seal designed to give indication of unauthorized entry. The seal includes a fingerprint feature that provides seal identity information in addition to the unique fiber optic pattern created when the seal is installed. The fiber optic cable used for the seal loop is produced with tamper resistant features that increase the difficulty of attacking that component of a seal. A Seal Reader has been developed that will record the seal signature and the fingerprint feature of the seal. A Correlator software program then compares seal images to establish a match or mismatch. SNL is also developing a Polaroid reader to permit hard copies of the seal patterns to be obtained directly from the seal.

  20. A fluid biopsy as investigating technology for the fluid phase of solid tumors

    Science.gov (United States)

    Kuhn, Peter; Bethel, Kelly

    2012-02-01

    Reliable measurement of internal bodily substances and structures is one of the cornerstones of modern medicine. Progress in cancer medicine, like that in many medical fields, must encompass and take advantage of progress in the physical sciences. Historically, the development and refinement of physical sciences-based detection of biological entities precedes periods of great advancements in therapies. To treat broken limbs and arthritis, we are indebted to Conrad Roentgen's discovery of x-rays by which we can evaluate the bones; to apply gamma knife therapy for cancer, we are indebted to Marie Curie's discoveries about radioactivity by which we can eradicate tumors; to manage the complications of diabetes, we are indebted to Tom Clemens, Ames Pharmaceuticals and Dick Bernstein's refinement of direct blood glucose measurement technology by which we can count, hour-to-hour, the waxing and waning of blood sugar levels; to understand anything at all on the cellular level, we are indebted to Antonie van Leeuwenhoek's microscope, by which we can see our cells. The application of physical sciences perspectives to biological and medical problems has a long and productive history. As of late, however, the increasing compartmentalization of science and exponential increases of knowledge in both arenas has resulted in a rift between the two. The NCI has initiated a research network establishing multiple centers of investigation, the Physical Sciences in Oncology Centers (http://physics.cancer.gov), which seek to mend the rift. Each headed by a pair of investigators, one in the physical sciences and one in the biological sciences, the centers seek to bring the advances and breakthroughs of the physical sciences world to bear on the question of cancer. This issue of physical biology contains a series of articles exploring the utility and applicability of a new method for measuring cancer as it spreads, developed at the Scripps Physical Oncology Center. Although some progress

  1. Development of wafer-level-packaging technology for simultaneous sealing of accelerometer and gyroscope under different pressures

    Science.gov (United States)

    Aono, T.; Suzuki, K.; Kanamaru, M.; Okada, R.; Maeda, D.; Hayashi, M.; Isono, Y.

    2016-10-01

    This research demonstrates a newly developed anodic bonding-based wafer-level-packaging technique to simultaneously seal an accelerometer in the atmosphere and a gyroscope in a vacuum with a glass cap for micro-electromechanical systems sensors. It is necessary for the accelerometer, with a damping oscillator, to be sealed in the atmosphere to achieve a high-speed response. As the gyroscope can achieve high sensitivity with a large displacement at the resonant frequency without air-damping, the gyroscope must be sealed in a vacuum. The technique consists of three processing steps: the first bonding step in the atmosphere for the accelerometer, the pressure control step and the second bonding step in a vacuum for the gyroscope. The process conditions were experimentally determined to achieve higher shear strength at the interface of the packaging. The packaging performance of the accelerometer and gyroscope after wafer-level packaging was also investigated using a laser Doppler velocimeter at room temperature. The amplitude at the resonant frequency of the accelerometer was reduced by air damping, and the quality factor of the gyroscope showed a value higher than 1000. The reliability of the gyroscope was also confirmed by a thermal cyclic test and an endurance test at high humidity and high temperature.

  2. Cryogenic Flange and Seal Evaluation

    Science.gov (United States)

    Ramirez, Adrian

    2014-01-01

    The assembly of flanges, seals, and pipes are used to carry cryogenic fluid from a storage tank to the vehicle at launch sites. However, after a certain amount of cycles these raised face flanges with glass-filled Teflon gaskets have been found to have torque relaxation and are as a result susceptible to cryogenic fluid leakage if not re-torqued. The intent of this project is to identify alternate combinations of flanges and seals which may improve thermal cycle performance and decrease re-torque requirements. The general approach is to design a test fixture to evaluate leak characteristics between spiral and concentric serrations and to test alternate flange and seal combinations. Due to insufficient time, it was not possible to evaluate these different types of combinations for the combination that improved thermal cycle performance the most. However, the necessary drawings for the test fixture were designed and assembled along with the collection of the necessary parts.

  3. A NEW TYPE ZERO LEAKING SEALING TECHNOLOGY MAGNETIC FLUID SEALING%一种新型零泄漏磁性流体密封技术

    Institute of Scientific and Technical Information of China (English)

    孙明礼; 李德才

    2006-01-01

    磁性流体密封是一种新型密封技术,具有零泄漏、寿命长、无磨损等其他密封技术所无可比拟的优点.介绍了磁性流体、磁性流体密封的原理、理论以及数值计算.并对磁性流体密封在化肥工业上应用前景作乐观的展望.

  4. Twist seal for high-pressure vessels such as space shuttle rocket motors

    Science.gov (United States)

    von Pragenau, George L. (Inventor)

    1989-01-01

    Seals for sealing clevis and flange joints (14) of a solid rocket booster motor, and more particularly to a seal (30) which is twisted upon application of expansion forces to an edge seal (36). This twisting motion initially causes a leading edge seal (44) to be urged into sealing engagement with a surface (48) of an adjacent member (20) and thereafter, increasing fluid pressure on a pressurized side (64) of a seal (30) drives a broad sealing region (46) into sealing engagement with a surface (48).

  5. 纳米磁性液体零泄漏密封保护器的实验研究%Experimental Study on Zero Leakage Sealing Protector of Nano-Magnetic Fluids

    Institute of Scientific and Technical Information of China (English)

    徐超熙; 安宏; 王珍; 李学慧

    2012-01-01

    在某些特殊密封场合下,阀的密封优良与否具有重要意义,零泄漏就显得尤为重要.利用电磁式磁性液体零泄漏保护器搭建实验平台,记录了不同性状磁性液体在不同励磁电流下的耐压值,对比这些曲线之间的差异.实验表明:磁性液体的耐压值与磁感应强度成正比,在同等磁感应强度下,除去在点240 mA附近之外,耐压值的高低顺序依次为:样本1、样本2、样本3.根据电磁式保护器各磁场下的耐压情况,设计出三种不同尺寸的永磁环,研制出永磁式磁性液体密封保护器,扩大了保护器适应范围,提高了保护器的安全性能.总结出相关结论,对磁性液体密封中磁性液体的选取提供指导.%In some special seal situations, whether the seal of the valve is better or not is important, and the zero leakage is particularly important. The experimental platform was built with the zero leakage protector of electromagnetic nano-magnetic fluid, the pressure-resisting capabilities of different magnetic fluids were recorded in different excitation currents, and the differences between theses curves were compared. The experiment shows that the pressure-resisting values vary directly as the magnetic density. At the same magnetic density except the point of 240 mA, the order from high to low of the pressure-resisting values is as follows:sample 1, sample 2, sample 3. By the pressure-resisting capabilities of the electromagnetic protector under different magnetic fields, the three permanent magnet rings with different sizes were designed, a protector of nano-magnetic fluid with permanent magnetic was developed, enlarging the range of application and improving the safety. The relevant conclusions are summed up to guide the choice of the right magnetic fluid for the magnetic fluid seal.

  6. Turbine with radial acting seal

    Energy Technology Data Exchange (ETDEWEB)

    Eng, Darryl S; Ebert, Todd A

    2016-11-22

    A floating brush seal in a rim cavity of a turbine in a gas turbine engine, where the floating brush seal includes a seal holder in which the floating brush seal floats, and a expandable seal that fits within two radial extending seal slots that maintains a seal with radial displacement of the floating brush seal and the seal holder.

  7. The COLD-SAT experiment for cryogenic fluid management technology

    Science.gov (United States)

    Schuster, J. R.; Wachter, J. P.; Vento, D. M.

    1990-01-01

    The COLD-SAT spacecraft design experiments are described. COLD-SAT will be placed into an initial 1300 km circular orbit by an Atlas commercial launch vehicle. Electric power, experiment control and data management, attitude control, and propulsive accelarations for the experiments will be provided by the three-axis-controlled spacecraft bus. To provide data on the effects that low gravity levels might have on the heat and mass transfer processes involved, low levels of accelaration will be created. The COLD-SAT experiment will be configured into a module. The spacecraft experiment module will include three liquid hydrogen tanks; fluid transfer, pressurization and venting equipment; and instrumentation. Since the largest tank has helium-purged MLI to prevent ingress and freezing of air on the launchpad, it will contain all the liquid hydrogen at the point of launching. The hydrogen tanking system used for the Centaur upper stage of the Atlas will load and top off this tank. Atlas, with its liquid hydrogen upper stage, large payload fairing, and large launch margin, simplifies COLD-SAT design and integration.

  8. Development of fluid system design technology for integral reactor

    Energy Technology Data Exchange (ETDEWEB)

    Lee, D. J.; Chang, M. H.; Kang, D. J. and others

    1999-03-01

    This study presents the technology development of the system design concepts of SMART, a multi-purposed integral reactor with enhanced safety and operability, for use in diverse usages and applications of the nuclear energy. This report contains the following; - Design characteristics - Performance and safety related design criteria - System description: Primary system, Secondary system, Residual heat removal system, Make-up system, Component cooling system, Safety system - Development of design computer code: Steam generator performance(ONCESG), Pressurizer performance(COLDPZR), Steam generator flow instability(SGINS) - Development of component module and modeling using MMS computer code - Design calculation: Steam generator thermal sizing, Analysis of feed-water temperature increase at a low flow rate, Evaluation of thermal efficiency in the secondary system, Inlet orifice throttling coefficient for the prevention of steam generator flow instability, Analysis of Nitrogen gas temperature in the pressurizer during heat-up process, evaluation of water chemistry and erosion etc. The results of this study can be utilized not only for the foundation technology of the next phase basic system design of the SMART but also for the basic model in optimizing the system concepts for future advanced reactors. (author)

  9. Regenerator seal

    Science.gov (United States)

    Davis, Leonard C.; Pacala, Theodore; Sippel, George R.

    1981-01-01

    A method for manufacturing a hot side regenerator cross arm seal assembly having a thermally stablilized wear coating with a substantially flat wear surface thereon to seal between low pressure and high pressure passages to and from the hot inboard side of a rotary regenerator matrix includes the steps of forming a flat cross arm substrate member of high nickel alloy steel; fixedly securing the side edges of the substrate member to a holding fixture with a concave surface thereacross to maintain the substrate member to a slightly bent configuration on the fixture surface between the opposite ends of the substrate member to produce prestress therein; applying coating layers on the substrate member including a wear coating of plasma sprayed nickel oxide/calcium flouride material to define a wear surface of slightly concave form across the restrained substrate member between the free ends thereon; and thereafter subjecting the substrate member and the coating thereon to a heat treatment of 1600.degree. F. for sixteen hours to produce heat stabilizing growth in the coating layers on the substrate member and to produce a thermally induced growth stress in the wear surface that substantially equalizes the prestress in the substrate whereby when the cross arm is removed from the fixture surface following the heat treatment step a wear face is formed on the cross arm assembly that will be substantially flat between the ends.

  10. Supercritical fluid (SCF) technologies: Assessment of applicability to installation restoration processes

    Science.gov (United States)

    1994-03-01

    USAEC has conducted an evaluation of supercritical fluid (SCF) technologies for their applicability to treatment of explosives, chlorinated hydrocarbons, and metals in soils, water, and/or waste sludge media. Off-specification explosives and propellants that have traditionally been open burned or openly detonated were also examined. Supercritical fluids are substances which have been heated and compressed to above their critical temperatures and pressures and which possess unique transport and mass transfer properties. Supercritical fluid extraction (SFE) uses the solvating properties of supercritical fluids to extract one or more organic components from a mixture into a supercritical solvent (commonly CO2). The concentrated extract stream may then be recycled, reclaimed, or destroyed by other methods.

  11. Forming a Turbomachinery Seals Working Group: An Overview and Discussion

    Science.gov (United States)

    Proctor, Margaret P.

    2007-01-01

    Purose: Identify technical challenges to improving turbomachinery seal leakage and wear performance, reliability and cost effectiveness. Develop a coordinated effort to resolve foundational issues for turbomachinery seal technologies. Identify and foster opportunities for collaboration. Advocate for funding.

  12. On-line fingerprinting of fluids using coaxial stub resonator technology

    NARCIS (Netherlands)

    Hoog-Antonyuk, N.A.; Olthuis, Wouter; Mayer, M.J.J.; Yntema, D.; Miedema, H.; van den Berg, Albert

    2012-01-01

    Here we demonstrate the proof-of-principle of a coaxial stub resonator to assess the dielectric properties of fluids. This radio-frequency spectroscopy method is based on coaxial stub technology and comprises quarter wave length open-ended resonators that are filled with a liquid sample as

  13. Technologies for Extracting Valuable Metals and Compounds from Geothermal Fluids

    Energy Technology Data Exchange (ETDEWEB)

    Harrison, Stephen [SIMBOL Materials

    2014-04-30

    Materials is evaluating other products with greater commercial value. Potassium Silicotitanates, zeolites and other sorbents were evaluated as potential reagents for the extraction of potassium from geothermal brines and production of potassium chloride (potash). It was found that zeolites were effective at removing potassium but the capacity of the zeolites and the form that the potassium is in does not have economic potential. Iron-silica by-product The conversion of iron-silica by-product produced during silica management operations into more valuable materials was studied at the laboratory scale. Results indicate that it is technically feasible to convert the iron-silica by-product into ferric chloride and ferric sulfate solutions which are precursors to a ferric phosphate product. However, additional work to purify the solutions is required to determine the commercial viability of this process. Conclusion Simbol Materials is in the process of designing its first commercial plant based on the technology developed to the pilot scale during this project. The investment in the commercial plant is hundreds of millions of dollars, and construction of the commercial plant will generate hundreds of jobs. Plant construction will be completed in 2016 and the first lithium products will be shipped in 2017. The plant will have a lithium carbonate equivalent production capacity of 15,000 tonnes per year. The gross revenues from the project are expected to be approximately $ 80 to 100 million annually. During this development program Simbol grew from a company of about 10 people to over 60 people today. Simbol is expected to employ more than 100 people once the plant is constructed. Simbol Materials’ business is scalable in the Imperial Valley region because there are eleven geothermal power plants already in operation, which allows Simbol to expand its business from one plant to multiple plants. Additionally, the scope of the resource is vast in terms of potential products such

  14. 电子印章在南京市科技金融服务平台中的应用%Application of Electronic Seal in Nanjing Technology and Financial Services Platform

    Institute of Scientific and Technical Information of China (English)

    郑倩

    2015-01-01

    文章利用电子印章技术提供一种网上审核解决方案,不仅方便了企业用户,还减少了打印及盖章环节,进一步促进无纸化办公,同时提高了系统的安全性。%This paper provides a systematic solution using electronic seal technology. It is not only convenient for business users,reduce the print and seal time,promote paperless office, but also improve the security of the system.

  15. Experimental study on a magnetofluid sealing liquid for propeller shaft

    Institute of Scientific and Technical Information of China (English)

    ZHAO Chang-fa; SUN Rong-hua; ZHENG Jin-xing

    2003-01-01

    The selecting and preparing method of the basic material of magnetic fluid was introduced. By using a chemical method, the magnetic micropowder Fe3O4 was successfully yielded, and an oil-base as a working carrier and dispersing agent was determined. The preparation process of the magnetic fluid and prescription of the oil-base magnetic fluid were discussed. The simulation experimental rig of magnetic fluid sealing for propeller shaft was designed. The sealing ability experiment was conducted and results were analyzed. The pressure of sealing is up to 2 Mpa.

  16. Microfabrication of hybrid fluid membrane for microengines

    Science.gov (United States)

    Chutani, R.; Formosa, F.; de Labachelerie, M.; Badel, A.; Lanzetta, F.

    2015-12-01

    This paper describes the microfabrication and dynamic characterization of thick membranes providing a technological solution for microengines. The studied membranes are called hybrid fluid-membrane (HFM) and consist of two thin membranes that encapsulate an incompressible fluid. This work details the microelectromechanical system (MEMS) scalable fabrication and characterization of HFMs. The membranes are composite structures based on Silicon spiral springs embedded in a polymer (RTV silicone). The anodic bonding of multiple stacks of Si/glass structures, the fluid filling and the sealing have been demonstrated. Various HFMs were successfully fabricated and their dynamic characterization demonstrates the agreement between experimental and theoretical results.

  17. Fluid Vessel Quantity Using Non-invasive PZT Technology Flight Volume Measurements Under Zero G Analysis

    Science.gov (United States)

    Garofalo, Anthony A

    2013-01-01

    The purpose of the project is to perform analysis of data using the Systems Engineering Educational Discovery (SEED) program data from 2011 and 2012 Fluid Vessel Quantity using Non-Invasive PZT Technology flight volume measurements under Zero G conditions (parabolic Plane flight data). Also experimental planning and lab work for future sub-orbital experiments to use the NASA PZT technology for fluid volume measurement. Along with conducting data analysis of flight data, I also did a variety of other tasks. I provided the lab with detailed technical drawings, experimented with 3d printers, made changes to the liquid nitrogen skid schematics, and learned how to weld. I also programmed microcontrollers to interact with various sensors and helped with other things going on around the lab.

  18. Fluid Vessel Quantity using Non-Invasive PZT Technology Flight Volume Measurements Under Zero G Analysis

    Science.gov (United States)

    Garofalo, Anthony A.

    2013-01-01

    The purpose of the project is to perform analysis of data using the Systems Engineering Educational Discovery (SEED) program data from 2011 and 2012 Fluid Vessel Quantity using Non-Invasive PZT Technology flight volume measurements under Zero G conditions (parabolic Plane flight data). Also experimental planning and lab work for future sub-orbital experiments to use the NASA PZT technology for fluid volume measurement. Along with conducting data analysis of flight data, I also did a variety of other tasks. I provided the lab with detailed technical drawings, experimented with 3d printers, made changes to the liquid nitrogen skid schematics, and learned how to weld. I also programmed microcontrollers to interact with various sensors and helped with other things going on around the lab.

  19. Numerical and experimental evaluation of performance of centrifugal seals

    Indian Academy of Sciences (India)

    T V SANAND; P PRADEEP KUMAR; P UNNIKRISHNAN NAIR; PAUL P GEORGE

    2017-04-01

    ‘Centrifugal seals’ or ‘Slinger seals’ offer an attractive choice as non-contact-type sealing in fluid machinery. These seals utilize the radial pressure gradient caused by centrifugal forces in a rotating fluid ring, to create a sealing of the working fluid. Basic construction of a typical seal consists of a rotating disc inside astationary casing; one side of the disc (sealing side) is provided with a set of slots (Type-1) or vanes (Type-2) to enhance the tangential velocity of the fluid. The other side of the disk (back side) in both the configurations is exposed to high pressure liquid being sealed. Both numerical and experimental investigations of the performance of Type-1 seal (with slots) have been carried out so as to optimize the seal configuration to achieve maximum sealing capacity, with minimum power consumption. A comparison of the performance of Type-1 seal has been made with that of conventional one (Type-2) in view of economy of construction and better sealing with minimal expense of power consumption. A test rig that allows for varying the major geometrical and operating parameters was designed and tests were conducted with water as the medium. Influence of major geometric parameters like dimensions and number of slots, axial/radial clearances and major operating parameters like rotational speed, inlet pressure and sealing fluid bypass flow rate has been investigated. Apart from variouspressure, temperature, flow and torque measurements, the interface between the sealing and working fluid for the experiments was captured and recorded using a high speed camera at 26,000 frames per second. Geometrical configuration for the slots that maximizes the sealing capacity is arrived through 3D numerical simulations using commercial CFD solver ANSYS Fluent®. A good agreement is obtained with respect to experimental results. In view of economy of construction and better sealing with minimal expense of operating power, a modified version of Type-1 seal

  20. Method of effecting expanding chemical anchor/seals for rock cavities

    Energy Technology Data Exchange (ETDEWEB)

    Swanson, D.; Schlump, M.

    1989-06-20

    This method discusses sealing a cavity formed in a rock against the passage of fluids without fracturing the rock; by placing wadding in the cavity and adding a supply of expanding chemical grout; a seal was been developed upon hardening.

  1. Adhesive sealing of the pulp chamber.

    Science.gov (United States)

    Belli, S; Zhang, Y; Pereira, P N; Pashley, D H

    2001-08-01

    The purpose of this in vitro study was to evaluate quantitatively the ability of four different filling materials to seal the orifices of root canals as a secondary seal after root canal therapy. Forty extracted human molar teeth were used. The top of pulp chambers and distal halves of the roots were removed using an Isomet saw. The canal orifices were temporarily sealed with a gutta-percha master cone without sealer. The pulp chambers were then treated with a self-etching primer adhesive system (Clearfil SE Bond), a wet bonding system (One-Step), a 4-methacryloyloxyethyl trimellitate anhydride adhesive system (C&B Metabond), or a reinforced zinc oxide-eugenol (IRM). The specimens were randomly divided into four groups of 10 each. A fluid filtration method was used for quantitative evaluation of leakage. Measurements of fluid movement were made at 2-min intervals for 8 min. The quality of the seal of each specimen was measured by fluid filtration immediately and after 1 day, 1 wk, and 1 month. Even after 1 month the resins showed an excellent seal. Zinc oxide-eugenol had significantly more leakage when compared with the resin systems (p < 0.05). Adhesive resins should be considered as a secondary seal to prevent intraorifice microleakage.

  2. Clinical procedure in sealing pit and fissure using technological aids: VistaCam iX Proof and Combi

    Directory of Open Access Journals (Sweden)

    Fabrizio Guerra

    2016-03-01

    Full Text Available The effectiveness of sealants in preventing pits and fissures decay is currently assessed by retention as principal clinical evaluation criteria. Among the determinants for sealant retention, an incomplete removal of plaque debris can cause lack of adhesion at the sealant-enamel interface. Therefore, in order to optimize the caries prevention outcome, clinical procedures of biofilm detection and cleansing are crucial. Technological aids can help clinicians in these critical phases. A clinical procedure is described of sealant application using VistaCam iX Proof fluorescence camera for quantitative assessment of surface demineralization and Combi air polishing unit for plaque removal. Pre and post air polishing intraoral VistaCam iX Proof images show the effectiveness of glycine airpolish technology in plaque removal. The results encourage technological aided clinical procedures in enhancing sealant application for pit and fissures caries prevention. Further clinical research is needed to validate our preliminary outcomes.

  3. Non-contacting shaft seals for gas and steam turbines

    OpenAIRE

    2012-01-01

    Improvements upon current gas turbine sealing technology performance are essential for decreasing specific fuel consumption to meet stringent future efficiency targets. The clearances between rotating and static components of a gas turbine, which need to be sealed, vary over a flight cycle. Hence, a seal which can passively maintain an optimum clearance, whilst preventing contact between itself and the rotor, is extremely desirable. Various configurations of a Rolls Royce (RR) seal concep...

  4. 螺旋槽机械密封摩擦副界面流固耦合分析%Fluid-solid Coupling Analysis of the Friction Pair Interface for Spiral Groove Mechanical Seal

    Institute of Scientific and Technical Information of China (English)

    李宁; 穆塔里夫•阿赫迈德; 吕星刚

    2016-01-01

    Based on the 3D finite element models of the fluid-film and solid of the friction pair interface for spiral groove me-chanical seal,the fluid-film between the faces of the static and dynamic is simulated ,and the law of the pressure distribution was obtained,the result show that pressure distribution is nonlinear.After that,the pressure was imported into static analysis module as one boundary condition of dynamic ring,then the one-way fluid-solid weak coupling was achieved by automatic iterative of the two steps.,the values indicate that the maximum deformation occurs on the spiral groove in the face of dynamic ring,while the maxi-mum stress occurs on the end of the spiral groove.Further,the effect of the rotational speed of dynamic ring,the pressure differ-ence and the viscosity on the maximum deformation and stress were also studied,the result provide a beneficial reference for the optimization of sealing performance.%基于建立的三维螺旋槽机械密封摩擦副界面的流、固有限元模型,数值模拟了动静环端面间的流体膜,得到液膜的压力分布规律,结果显示压力呈非线性分布;然后将得到的压力值作为边界条件之一导入到动环端面的静力学分析中,利用两者接触面间的自动迭代计算实现单向弱流固耦合分析,结果表明:最大变形发生在动环端面螺旋槽处,而最大应力发生在螺旋槽顶端;并进一步研究了动环的转速以及介质压力和粘度对最大变形和最大应力的影响规律,为密封性能的优化提供了有益的参考。

  5. Discussion on the development of technology of the compressor shaft seal%压缩机轴封发展技术探讨

    Institute of Scientific and Technical Information of China (English)

    王恒卓; 杨烨

    2014-01-01

    Centrifugal compressor are introduced. The sealing principle,common development. Focusing on the dry gas seal application status and development trend. And a brief analysis of the development status of seal. Draw:dry gas seal and magnetic bearing is a key point of the development direction of the sealing the future.%介绍了离心压缩机常见密封发展历程、工作原理。重点阐述了干气密封运用现状及其发展趋势。并就密封发展现状做了简要分析。得出:干气密封和磁力轴承是未来密封发展重点方向。

  6. Serum and follicular fluid organochlorine concentrations among women undergoing assisted reproduction technologies

    Directory of Open Access Journals (Sweden)

    Ryan Louise

    2009-07-01

    Full Text Available Abstract Background Exposure to persistent organic pollutants, including polychlorinated biphenyls (PCBs and organochlorine pesticides, is widespread among the general population. There is evidence of adverse effects on reproduction and early pregnancy in relation to organochlorine exposure but human studies remain limited. The increased use of assisted reproductive technologies (ART presents unique opportunities for the assessment of environmental influences on early pregnancy outcomes not otherwise observable in humans, but studies need to be designed to maximize the efficiency of the exposure data collected while minimizing exposure measurement error. Methods The present study was conducted to assess the correlation between concentrations of organochlorines in serum and follicular fluid samples collected from a subset of women undergoing ART in a large study that took place between 1994 and 2003, as well as the temporal reliability of serum organochlorine concentrations among women undergoing multiple ART cycles in the study. PCB congeners (118, 138, 153, and 180, 1,1,1-trichloro-2,2-bis(p-chlorophenylethane (p,p'-DDT, the DDT metabolite p,p'-DDE, hexachlorobenzene (HCB, oxychlordane, trans-nonachlor and mirex were measured in 72 follicular fluid samples and 265 serum samples collected from 110 women. Results Organochlorine concentrations in paired serum and follicular fluid samples were correlated, with Pearson and Spearman coefficients ranging from 0.60 to 0.92. Serum organochlorine concentrations were two- to three-fold greater than in follicular fluid, and a significant inverse trend was observed in the distribution of follicular fluid:serum ratios with increasing molecular weight of the compound (p-value for trend Conclusion Our results support the use of a single serum sample to adequately represent a more biologically relevant dose (concentrations in follicular fluid, as well as exposure levels over time, in epidemiological studies of

  7. Manufacturing Solid Dosage Forms from Bulk Liquids Using the Fluid-bed Drying Technology.

    Science.gov (United States)

    Qi, Jianping; Lu, Y I; Wu, Wei

    2015-01-01

    Solid dosage forms are better than liquid dosage forms in many ways, such as improved physical and chemical stability, ease of storage and transportation, improved handling properties, and patient compliance. Therefore, it is required to transform dosage forms of liquid origins into solid dosage forms. The functional approaches are to absorb the liquids by solid excipients or through drying. The conventional drying technologies for this purpose include drying by heating, vacuum-, freeze- and spray-drying, etc. Among these drying technologies, fluidbed drying emerges as a new technology that possesses unique advantages. Fluid-bed drying or coating is highly efficient in solvent removal, can be performed at relatively low temperatures, and is a one-step process to manufacture formulations in pellet forms. In this article, the status of the art of manufacturing solid dosage forms from bulk liquids by fluid-bed drying technology was reviewed emphasizing on its application in solid dispersion, inclusion complexes, self-microemulsifying systems, and various nanoscale drug delivery systems.

  8. Tamper-Indicating Quantum Seal*

    Science.gov (United States)

    Williams, Brian P.; Britt, Keith A.; Humble, Travis S.

    2016-01-01

    Technical means for identifying when tampering occurs is a critical part of many containment and surveillance technologies. Conventional fiber-optic seals provide methods for monitoring enclosed inventories, but they are vulnerable to spoofing attacks based on classical physics. We address these vulnerabilities with the development of a quantum seal that offers the ability to detect the intercept-resend attack using quantum integrity verification. Our approach represents an application of entanglement to provide guarantees in the authenticity of the seal state by verifying it is transmitted coherently. We implement these ideas using polarization-entangled photon pairs that are verified after passing through a fiber-optic-channel test bed. Using binary-detection theory, we find the probability of detecting inauthentic signals is greater than 0.9999 with a false-alarm chance of 1 0-9 for a 10-s sampling interval. In addition, we show how the Hong-Ou-Mandel effect concurrently provides a tight bound on redirection attack, in which tampering modifies the shape of the seal. Our measurements limit the tolerable path-length change to submillimeter disturbances. These tamper-indicating features of the quantum seal offer unprecedented security for unattended monitoring systems.

  9. Whole Missile Sealing Detection Device and Technology Solutions%全弹密封检测装置及技术方案

    Institute of Scientific and Technical Information of China (English)

    马宏亮

    2013-01-01

    In order to overcome the defect of positive pressure water leak detection method, helium mass spectrometer leak detection method, and dry air differential pressure leak detection method. Design a sealing detection device for testing whole missile. Analyze composition and function of the device, give the technological process and technical parameters. The results show that the method with high sensitivity and convenient operation, can realize multi-location detection at the same time, and greatly improve work efficiency.%针对正压浸水检漏法、氦质谱仪检漏法和干空压差检漏法3种检测方法的不足,设计一种全弹密封检测装置用于全弹的检测。分析装置组成与功能,给出其工艺流程和相关技术参数。结果表明:该方法灵敏度高,操作方便,可实现多工位同时检测,大大提升工作效率。

  10. Fluid bed drying as upgrading technology for feasible treatment of Kolubara lignite

    Directory of Open Access Journals (Sweden)

    Erić Milić D.

    2016-01-01

    Full Text Available An overview of the current status of low-rank coal upgrading technologies is presented in the paper, particularly with respect to drying and dewatering procedures. In order to calculate the significant parameters of the moisture removal process, a model of convective coal drying in a fluid bed, based on the two-phase (bubbling fluidization model proposed by Kunii and Levenspiel, is developed and presented. Product-specific data (intraparticle mass transfer, gas-solid moisture equilibrium related to the particular coal variety addressed here (Kolubara lignite are obtained through preliminary investigations. Effective thermal conductivity of the packed bed as defined by Zehner/Bauer/Schlünder is used to define heat transfer mechanisms occurring in the suspension phase of the fluid bed. A completely new set of experimental data obtained has been successfully used to validate the model additionally. [Projekat Ministarstva nauke Republike Srbije, br. TR33050 i III42010

  11. Magnetically Actuated Seal

    Science.gov (United States)

    Pinera, Alex

    2013-01-01

    This invention is a magnetically actuated seal in which either a single electromagnet, or multiple electromagnets, are used to control the seal's position. This system can either be an open/ close type of system or an actively controlled system.

  12. Magnetically Actuated Seal Project

    Data.gov (United States)

    National Aeronautics and Space Administration — FTT proposes development of a magnetically actuated dynamic seal. Dynamic seals are used throughout the turbopump in high-performance, pump-fed, liquid rocket...

  13. Seal Out Tooth Decay

    Science.gov (United States)

    ... Decay (Caries) > Seal Out Tooth Decay Seal Out Tooth Decay Main Content What are dental sealants? How are ... fix decayed teeth. Back to Top What causes tooth decay? Germs in the mouth use the sugar in ...

  14. Sealing weak gel completion fluid system for loose sand depleted reservoir%适用于疏松砂岩衰竭油藏的封堵型弱凝胶完井液体系

    Institute of Scientific and Technical Information of China (English)

    苏宇驰; 范白涛; 赵少伟

    2015-01-01

    Loose sandstone heavy oil reservoir is characterized as shallow buried,low temperature,poor lithology and loose cementation. It employs high-velocity water flow to conduct gravel packer completion,which result to leakage of completion fluid. Therefore a sealing weak gel completion fluid for loose sand depleted reservoir is developed. The recipe is as followed:filtering sea water+0.25%Na2CO3+0.7%FCNQ+2.0% filtrate reducer;Gel breaking liquid recipe:filtering sea water+3% new gel breaker +3%KCl. The reduction rate of leakage is greater than 90% when the fluid is applied,and core permeability recovery value comes to 86.8% with good reservoir protection. The fluid has strong suspension stability and good compatibility with later work fluids. It proves to be successful in SZ36-1 block,Bohai Oilfield.%疏松的砂岩稠油油藏储层具有的特征如下:温度低、埋藏浅、胶结疏松以及成岩性差等.该类油藏大都采用高速水流进行砾石充填完井,这就导致了完井液大量漏失等问题.基于以上考虑,在室内试验室研究出了适合疏松的砂岩稠油油藏储层的封堵型弱凝胶完井液.弱凝胶封堵配方:0.7%流型调节剂+2.0%降滤失剂+0.25%Na2CO3+海水.破胶液配方:3%新型破胶剂+3%KCl+海水.该体系使用后漏失降低率大于90%,解堵后岩心的渗透率恢复值达到86.8%,储层保护效果好,并且悬浮稳定性强,与后续工作液的配伍性好.渤海海域上绥中36-1区块广泛应用了本完井液体系并能很好地解决工程实际问题.

  15. Low torque hydrodynamic lip geometry for rotary seals

    Energy Technology Data Exchange (ETDEWEB)

    Dietle, Lannie L.; Schroeder, John E.

    2015-07-21

    A hydrodynamically lubricating geometry for the generally circular dynamic sealing lip of rotary seals that are employed to partition a lubricant from an environment. The dynamic sealing lip is provided for establishing compressed sealing engagement with a relatively rotatable surface, and for wedging a film of lubricating fluid into the interface between the dynamic sealing lip and the relatively rotatable surface in response to relative rotation that may occur in the clockwise or the counter-clockwise direction. A wave form incorporating an elongated dimple provides the gradual convergence, efficient impingement angle, and gradual interfacial contact pressure rise that are conducive to efficient hydrodynamic wedging. Skewed elevated contact pressure zones produced by compression edge effects provide for controlled lubricant movement within the dynamic sealing interface between the seal and the relatively rotatable surface, producing enhanced lubrication and low running torque.

  16. Hydraulic forces caused by annular pressure seals in centrifugal pumps

    Science.gov (United States)

    Iino, T.; Kaneko, H.

    1980-01-01

    The hydraulic forces caused by annular pressure seals were investigated. The measured inlet and exit loss coefficients of the flow through the seals were much smaller than the conventional values. The results indicate that the damping coefficient and the inertia coefficient of the fluid film in the seal are not affected much by the rotational speed or the eccentricity of the rotor, though the stiffness coefficient seemed to be influenced by the eccentricity.

  17. Turbomachine Interface Sealing

    Science.gov (United States)

    Hendricks, Robert C.; Chupp, Raymond E.; Lattime, Scott B.; Steinetz, Bruce M.

    2005-01-01

    Sealing interfaces and coatings, like lubricants, are sacrificial, giving up their integrity for the benefit of the component. Clearance control is a major issue in power systems turbomachine design and operational life. Sealing becomes the most cost-effective way to enhance system performance. Coatings, films, and combined use of both metals and ceramics play a major role in maintaining interface clearances in turbomachine sealing and component life. This paper focuses on conventional and innovative materials and design practices for sealing interfaces.

  18. Measurement component technology. Volume 1: Cryogenic pressure measurement technology, high pressure flange seals, hydrogen embrittlement of pressure transducer material, close coupled versus remote transducer installation and temperature compensation of pressure transducers

    Science.gov (United States)

    Hayakawa, K. K.; Udell, D. R.; Iwata, M. M.; Lytle, C. F.; Chrisco, R. M.; Greenough, C. S.; Walling, J. A.

    1972-01-01

    The results are presented of an investigation into the availability and performance capability of measurement components in the area of cryogenic temperature, pressure, flow and liquid detection components and high temperature strain gages. In addition, technical subjects allied to the components were researched and discussed. These selected areas of investigation were: (1) high pressure flange seals, (2) hydrogen embrittlement of pressure transducer diaphragms, (3) The effects of close-coupled versus remote transducer installation on pressure measurement, (4) temperature transducer configuration effects on measurements, and (5) techniques in temperature compensation of strain gage pressure transducers. The purpose of the program was to investigate the latest design and application techniques in measurement component technology and to document this information along with recommendations for upgrading measurement component designs for future S-2 derivative applications. Recommendations are provided for upgrading existing state-of-the-art in component design, where required, to satisfy performance requirements of S-2 derivative vehicles.

  19. Application of Fog Seal with Sand Technology in Fuzhou-Yinchuan Expressway Wensha Section%含砂雾封层技术在福银高速温沙段的应用

    Institute of Scientific and Technical Information of China (English)

    万超; 陈家

    2014-01-01

    针对福银高速温沙段路面病害发展情况,结合含砂雾封层技术的特点和工艺,选取2km试验段进行含砂雾封层施工,根据施工后的路面性能检测结果,含砂雾封层可在很大程度上提高沥青路面的抗渗性能,对沥青路面的表层形貌也有良好的改善作用,可将含砂雾封层技术在福银高速温沙段预防性养护中进行推广。%According to the disease development situation in Fuzhou-Yinchuan Expressway Wensha sec-tion, combined with the characteristics and process of fog seal with sand, the paper selects 2km test sec-tion to conduct construction of fog seal with sand. According to the test results of pavement performance after construction, fog seal with sand can improve the anti permeability performance of asphalt pavement greatly, and has good improvement effect on the appearance of the asphalt pavement surface, which shows that fog seal with sand technology can be popularized in preventive maintenance of Fuzhou-Yinchuan Ex-pressway Wensha section.

  20. Bentonite as a waste isolation pilot plant shaft sealing material

    Energy Technology Data Exchange (ETDEWEB)

    Daemen, J.; Ran, Chongwei [Univ. of Nevada, Reno, NV (United States)

    1996-12-01

    Current designs of the shaft sealing system for the Waste Isolation Pilot Plant (WIPP) propose using bentonite as a primary sealing component. The shaft sealing designs anticipate that compacted bentonite sealing components can perform through the 10,000-year regulatory period and beyond. To evaluate the acceptability of bentonite as a sealing material for the WIPP, this report identifies references that deal with the properties and characteristics of bentonite that may affect its behavior in the WIPP environment. This report reviews published studies that discuss using bentonite as sealing material for nuclear waste disposal, environmental restoration, toxic and chemical waste disposal, landfill liners, and applications in the petroleum industry. This report identifies the physical and chemical properties, stability and seal construction technologies of bentonite seals in shafts, especially in a saline brine environment. This report focuses on permeability, swelling pressure, strength, stiffness, longevity, and densification properties of bentonites.

  1. Preparation of microcellular composites with biomimetic structure via supercritical fluid technology

    Institute of Scientific and Technical Information of China (English)

    2001-01-01

    A new microcellular composite material with a biomimetic structure has been prepared via the supercritical fluid (SCF) technology. The resultant material has a clear biomimetic structure like bamboo and wood. The skin region is enriched with oriented high-strength thermotropic liquid crystal polymer fibrils, while the core region with polystyrene (PS) micro-cells. The diameter and density of micro- cells can be controlled by the processing parameters such as temperature and pressure. And the skin thickness can be controlled conveniently by varying the composition of polystyrene and liquid crystal polymer.

  2. Performance Characteristics and Temperature Compensation Method of Fluid Property Sensor Based on Tuning-Fork Technology

    Directory of Open Access Journals (Sweden)

    Yuan Chen

    2016-01-01

    Full Text Available Fluid property sensor (FPS based on tuning-fork technology is applied to the measurement of the contaminant level of lubricant oil. The measuring principle of FPS sensor is derived and proved together with its resolution. The performance characteristics of the FPS sensor, such as sensitivity coefficient, resolution, and quality factor, are analyzed. A temperature compensation method is proposed to eliminate the temperature-dependence of the measuring parameters, and its validity is investigated by numerical simulation of sensitivity, oscillating frequency, and dielectric constant. The values of purification efficiency obtained using microwave and without microwave are compared experimentally.

  3. Wearable technology for bio-chemical analysis of body fluids during exercise.

    Science.gov (United States)

    Morris, Deirdre; Schazmann, Benjamin; Wu, Yangzhe; Coyle, Shirley; Brady, Sarah; Fay, Cormac; Hayes, Jer; Lau, King Tong; Wallace, Gordon; Diamond, Dermot

    2008-01-01

    This paper details the development of a textile based fluid handling system with integrated wireless biochemical sensors. Such research represents a new advancement in the area of wearable technologies. The system contains pH, sodium and conductivity sensors. It has been demonstrated during on-body trials that the pH sensor has close agreement with measurements obtained using a reference pH probe. Initial investigations into the sodium and conductivity sensors have shown their suitability for integration into the wearable system. It is thought that applications exist in personal health and sports performance and training.

  4. [The extraction technology of epigoitri from isatidis radix by supercritical CO2 fluid].

    Science.gov (United States)

    Nian, Si-Hui; Liu, Chun-Yun; Liu, Li-Min; Yang, Li-Fen

    2013-07-01

    To study the extraction technology of epigoitri from Isatidis Radix by supercritical CO2 fluid. The effects of pressure, temperature, time, concentration and dosage of alcohol were studied by single factor analysis and orthogonal test. The optimized conditions were as follows: The pressure was 20 MPs, the temperature was 50 degrees C, the time was 2 h, concentration of alcohol was 100%, dosage was 80 mL. The content of epigoitri in the extract could reach 38.63% under the above conditions. This method is simple, rapid and it is suitable for the extraction of epigoitri from Isatidis Radix.

  5. Dynamic analysis of C/C composite finger seal

    Institute of Scientific and Technical Information of China (English)

    Chen Guoding; Wang Li’na; Yu Qiangpeng; Su Hua

    2014-01-01

    A seal device as an important component of aeroengines has decisive influence on per-formance, reliability, and working life of aeroengines. With the development of aeroengines, demands on the performance characteristics of seal devices are made strictly. Finger seal as a novel kind of sealing device, recently attracts more and more attentions in academic circles and engineer-ing fields at home and abroad. Research on finger seals has been extensively developed, especially on leakage and wear performances under dynamic conditions. However, it is a pity that the work on finger seals has been limited with a single approach that is improving the performance by structural optimization;in addition, the technology of dynamic analysis on finger seals is weak. Aiming at the problems mentioned above, a distributed mass equivalent dynamic model of finger seals considering the coupling effect of overlaid laminates is established in the present paper, the dynamic perfor-mance of 2.5 dimension C/C composite finger seal is analyzed with the model, and then the effects of fiber bundle density and fiber bundle preparation direction on finger seal’s dynamic performance are discussed, as well as compared with those of Co-based alloy finger seal. The current work is about dynamic analysis of finger seals and application of C/C composite in this paper may have much academic significance and many engineering values for improving research level of finger seal dynamics and exploring feasibility of C/C composite being used for finger seals.

  6. Dynamic analysis of C/C composite finger seal

    Directory of Open Access Journals (Sweden)

    Chen Guoding

    2014-06-01

    Full Text Available A seal device as an important component of aeroengines has decisive influence on performance, reliability, and working life of aeroengines. With the development of aeroengines, demands on the performance characteristics of seal devices are made strictly. Finger seal as a novel kind of sealing device, recently attracts more and more attentions in academic circles and engineering fields at home and abroad. Research on finger seals has been extensively developed, especially on leakage and wear performances under dynamic conditions. However, it is a pity that the work on finger seals has been limited with a single approach that is improving the performance by structural optimization; in addition, the technology of dynamic analysis on finger seals is weak. Aiming at the problems mentioned above, a distributed mass equivalent dynamic model of finger seals considering the coupling effect of overlaid laminates is established in the present paper, the dynamic performance of 2.5 dimension C/C composite finger seal is analyzed with the model, and then the effects of fiber bundle density and fiber bundle preparation direction on finger seal’s dynamic performance are discussed, as well as compared with those of Co-based alloy finger seal. The current work is about dynamic analysis of finger seals and application of C/C composite in this paper may have much academic significance and many engineering values for improving research level of finger seal dynamics and exploring feasibility of C/C composite being used for finger seals.

  7. An entrance region friction factor model applied to annular seal analysis - Theory versus experiment for smooth and honeycomb seals

    Science.gov (United States)

    Elrod, D.; Nelson, C.; Childs, D.

    1989-01-01

    A friction factor model is developed for the entrance-region of a duct. The model is used in an annular gas seal analysis similar to Nelson's (1984). Predictions of the analysis are compared to experimental results for a smooth-stator/smooth-rotor seal and three honeycomb-stator/smooth-rotor seals. The model predicts a leakage and direct damping well. The model overpredicts the dependence of cross-coupled stiffness on fluid prerotation. The model predicts direct stiffness poorly.

  8. 2000 NASA Seal/Secondary Air System Workshop. Volume 1

    Science.gov (United States)

    Steinetz, Bruce M. (Editor); Hendricks, Robert C. (Editor)

    2001-01-01

    The 2000 NASA Seal/Secondary Air System Workshop covered four main areas: (1) overviews of NASA-sponsored Ultra-Efficient Engine Technology (UEET) and Access to Space Programs, with emphasis on program goals and seal needs; (2) review of turbine engine seal issues from the perspective of end users such as United Airlines; (3) reviews of sealing concepts, test results, experimental facilities, and numerical predictions; and (4) reviews of material development programs relevant to advanced seals development. The NASA UEET overview illustrates for the reader the importance of advanced technologies, including seals, in meeting future engine system efficiency and emission goals. GE, Pratt & Whitney, and Honeywell presented advanced seal development work being performed within their organizations. The NASA-funded GE/Stein Seal team has successfully demonstrated a large (3-ft. diam) aspirating seal that can withstand all anticipated pressures, speeds, and rotor runouts anticipated for a GE90 L.P. turbine balance piston location. GE/Stein Seal are fabricating a full-scale seal to be tested in a GE-90 ground test engine in early 2002. Pratt & Whitney and Stein Seal are investigating carbon seals to accommodate large radial movements anticipated in future geared-fan gearbox locations. Honeywell presented a finger seal design being considered for a high-temperature static combustor location incorporating ceramic finger elements. Successful demonstration of the braided carbon rope thermal barriers to extreme temperatures (5500 F) for short durations provide a new form of very high temperature thermal barrier for future Shuttle solid rocket motor nozzle joints. The X-37, X-38, and future highly reusable launch vehicles pose challenging control surface seal demands that require new seal concepts made from emerging high temperature ceramics and other materials.

  9. Epoxy resins used to seal brachytherapy seed

    Energy Technology Data Exchange (ETDEWEB)

    Ferreira, Natalia Carolina Camargos; Ferraz, Wilmar Barbosa; Reis, Sergio Carneiro dos; Santos, Ana Maria Matildes dos, E-mail: nccf@cdtn.br, E-mail: ferrazw@cdtn.br, E-mail: reissc@cdtn.br, E-mail: amms@cdtn.br [Centro de Desenvolvimento da Tecnologia Nuclear (CDTN/CNEN-MG), Belo Horizonte, BH (Brazil)

    2013-07-01

    Prostate cancer treatment with brachytherapy is recommended for patients with cancer at an early stage. In this treatment, small radioactive seeds are implanted directly in the prostate gland. These seeds are composed at least of one radionuclide carrier and an X-ray marker enclosed within a metallic tube usually sealed by laser process. This process is expensive and, furthermore, it can provoke a partial volatilization of the radionuclide and change the isotropy in dose distribution around the seed. In this paper, we present a new sealing process using epoxy resin. Three kinds of resins were utilized and characterized by scanning electron microscopy (SEM), energy dispersive X ray (EDS) and by differential scanning calorimetry (DSC) after immersion in simulated body fluid (SBF) and in sodium iodine solution (NaI). The sealing process showed excellent potential to replace the sealing laser usually employed. (author)

  10. Low Cost, Durable Seal

    Energy Technology Data Exchange (ETDEWEB)

    Roberts, George; Parsons, Jason; Friedman, Jake

    2010-12-17

    Seal durability is critical to achieving the 2010 DOE operational life goals for both stationary and transportation PEM fuel cell stacks. The seal material must be chemically and mechanically stable in an environment consisting of aggressive operating temperatures, humidified gases, and acidic membranes. The seal must also be producible at low cost. Currentlyused seal materials do not meet all these requirements. This project developed and demonstrated a high consistency hydrocarbon rubber seal material that was able to meet the DOE technical and cost targets. Significant emphasis was placed on characterization of the material and full scale molding demonstrations.

  11. Drying Using Supercritical Fluid Technology as a Potential Method for Preparation of Chitosan Aerogel Microparticles.

    Science.gov (United States)

    Obaidat, Rana M; Tashtoush, Bassam M; Bayan, Mohammad F; Al Bustami, Rana T; Alnaief, Mohammad

    2015-12-01

    Supercritical fluid technology offers several advantages in preparation of microparticles. These include uniformity in particle size, morphology, and drug distribution without degradation of the product. One of the recent advantages is preparation of porous aerogel carrier with proper aerodynamic properties. In this study, we aimed to prepare chitosan aerogel microparticles using supercritical fluid (SCF) technology and compare that with microparticles produced by freeze drying (FD). Loading the prepared carriers with a model drug (salbutamol) was also performed. Comparisons of the particle properties and physicochemical characterizations were undertaken by evaluating particle size, density, specific surface area, and porosity. In vitro drug release studies were also investigated. The effect of many variables, such as molecular weight of chitosan oligomers, concentrations of chitosan, and concentrations of tripolyphosphate on the release, were also investigated. Chitosan aerogels were efficiently produced by SCF technology with an average particle size of 10 μm with a tapped density values around 0.12 g/mL, specific surface area (73-103) m(2)/g, and porosity (0.20-0.29) cc/g. Whereas, microparticles produced by FD method were characterized as cryogels with larger particle size (64 microns) with clear cracking at the surface. Sustained release profile was achieved for all prepared microparticles of salbutamol produced by the aforementioned methods as compared with pure drug. The results also demonstrates that chitosan molecular weight, polymer concentration, and tripolyphosphate concentration affected the release profile of salbutamol from the prepared microparticles. In conclusion, SCF technology was able to produce chitosan aerogel microparticles loaded with salbutamol that could be suitable for pulmonary drug delivery system.

  12. Zero leakage sealings

    Science.gov (United States)

    Kotesovec, Bernhard; Steinrück, Herbert

    2010-11-01

    The piston rod of a reciprocating compressor is sealed with elastic cylindrical sealing elements. Across the sealings the pressure drops from the operating pressure to the ambient pressure. The lubrication gap between the elastic sealing and reciprocating piston rod is studied with the aim to find conditions of a leakage free sealing. The flow in the lubrication gap and the elastic deformation of the sealing are determined simultaneously. The net-flow during one cycle of the reciprocating piston rod is calculated. It turns out that maintaining zero leakage is very sensible. Indeed the outbound flow during out-stroke has to be equal the inbound flow during the in-stroke. By prescribing a special shape of the undeformed sealing zero leakage can be attained - at least theoretically for certain operating conditions. It turns out that temperature dependent material data and a model for cavitation is necessary. The model, its numerical implementation and results will be discussed.

  13. Cryogenic Fluid Storage Technology Development: Recent and Planned Efforts at NASA

    Science.gov (United States)

    Moran, Matthew E.

    2009-01-01

    Recent technology development work conducted at NASA in the area of Cryogenic Fluid Management (CFM) storage is highlighted, including summary results, key impacts, and ongoing efforts. Thermodynamic vent system (TVS) ground test results are shown for hydrogen, methane, and oxygen. Joule-Thomson (J-T) device tests related to clogging in hydrogen are summarized, along with the absence of clogging in oxygen and methane tests. Confirmation of analytical relations and bonding techniques for broad area cooling (BAC) concepts based on tube-to-tank tests are presented. Results of two-phase lumped-parameter computational fluid dynamic (CFD) models are highlighted, including validation of the model with hydrogen self pressurization test data. These models were used to simulate Altair representative methane and oxygen tanks subjected to 210 days of lunar surface storage. Engineering analysis tools being developed to support system level trades and vehicle propulsion system designs are also cited. Finally, prioritized technology development risks identified for Constellation cryogenic propulsion systems are presented, and future efforts to address those risks are discussed.

  14. Compliant Glass Seals for SOFC Stacks

    Energy Technology Data Exchange (ETDEWEB)

    Chou, Y. S.; Choi, Jung-Pyung; Xu, Wei; Stephens, Elizabeth V.; Koeppel, Brian J.; Stevenson, Jeffry W.; Lara-Curzio, Edgar

    2014-04-01

    This report summarizes results from experimental and modeling studies performed by participants in the Solid-State Energy Conversion Alliance (SECA) Core Technology Program, which indicate that compliant glass-based seals offer a number of potential advantages over conventional seals based on de-vitrifying glasses, including reduced stresses during stack operation and thermal cycling, and the ability to heal micro-damage induced during thermal cycling. The properties and composition of glasses developed and/or investigated in these studies are reported, along with results from long-term (up to 5,800h) evaluations of seals based on a compliant glass containing ceramic particles or ceramic fibers.

  15. Compliant Glass Seals for SOFC Stacks

    Energy Technology Data Exchange (ETDEWEB)

    Chou, Yeong -Shyung [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Choi, Jung-Pyung [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Xu, Wei [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Stephens, Elizabeth V. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Koeppel, Brian J. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Stevenson, Jeffry W. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Lara-Curzio, Edgar [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States)

    2014-04-30

    This report summarizes results from experimental and modeling studies performed by participants in the Solid-State Energy Conversion Alliance (SECA) Core Technology Program, which indicate that compliant glass-based seals offer a number of potential advantages over conventional seals based on de-vitrifying glasses, including reduced stresses during stack operation and thermal cycling, and the ability to heal micro-damage induced during thermal cycling. The properties and composition of glasses developed and/or investigated in these studies are reported, along with results from long-term (up to 5,800h) evaluations of seals based on a compliant glass containing ceramic particles or ceramic fibers.

  16. Experimental and Simulation Studies on Cold Welding Sealing Process of Heat Pipes

    Science.gov (United States)

    Li, Yong; Chen, Shengle; Huang, Jinlong; Yan, Yuying; Zeng, Zhixin

    2017-03-01

    Sealing quality strongly affects heat pipe performance, but few studies focus on the process of heat pipe sealing. Cold welding sealing technology based on a stamping process is applied for heat pipe sealing. The bonding mechanism of the cold welding sealing process (CWSP) is investigated and compared with the experimental results obtained from the bonding interface analysis. An orthogonal experiment is conducted to observe the effects of various parameters, including the sealing gap, sealing length, sealing diameter, and sealing velocity on bonding strength. A method with the utilization of saturated vapor pressure inside a copper tube is proposed to evaluate bonding strength. A corresponding finite element model is developed to investigate the effects of sealing gap and sealing velocity on plastic deformation during the cold welding process. Effects of various parameters on the bonding strength are determined and it is found that the sealing gap is the most critical factor and that the sealing velocity contributes the least effect. The best parameter combination (A 1 B 3 C 1 D 3, with a 0.5 mm sealing gap, 6 mm sealing length, 3.8 mm sealing diameter, and 50 mm/s sealing velocity) is derived within the experimental parameters. Plastic deformation results derived from the finite element model are consistent with those from the experiment. The instruction for the CWSP of heat pipes and the design of sealing dies of heat pipes are provided.

  17. Repairing sealing surfaces on aluminum castings

    Science.gov (United States)

    Hanna, T. L.

    1980-01-01

    Approach using stylus nickel plating instead of copper and cadmium plating has simplified repair procedure. Damaged sealing surfaces are stylus nickelplated in one step. Superficial scratches and porous areas are removed more easily from repaired surface by simply lapping sealing areas to required finish. Although method is aimed for aerospace components, it may be easily incorporated into conventional aluminumcasting technology. One-step repair can be considered for cast-aluminum automobile and aircraft engines to reduce time and costs.

  18. Flippin' Fluid Mechanics - Using Online Technology to Enhance the In-Class Learning Experience

    Science.gov (United States)

    Webster, D. R.; Majerich, D. M.

    2013-11-01

    This study provides an empirical analysis of using online technologies and team problem solving sessions to shift an undergraduate fluid mechanics course from a traditional lecture format to a collaborative learning environment. Students were from two consecutive semesters of the same course taught by the same professor. One group used online technologies and solved problems in class and the other did not. Out of class, the treatment group watched 72 short (11 minutes, average) video lectures covering course topics and example problems being solved. Three times a week students worked in teams of two to solve problems on desktop whiteboard tablets while the instructor and graduate assistants provided ``just-in-time'' tutoring. The number of team problems assigned during the semester exceeded 100. Weekly online homework was assigned to reinforce topics. The WileyPlus online system generated unique problem parameters for each student. The control group received three-50 minute weekly lectures. Data include three midterms and a final exam. Regression results indicate that controlling for all of the entered variables, for every one more problem solving session the student attended, the final grade was raised by 0.327 points. Thus, if a student participated in all 25 of the team problem solving sessions, the final grade would have been 8.2 points higher, a difference of nearly a grade. Using online technologies and teamwork appeared to result in improved achievement, but more research is needed to support these findings.

  19. Dynamic sealing principles

    Science.gov (United States)

    Zuk, J.

    1976-01-01

    The fundamental principles governing dynamic sealing operation are discussed. Different seals are described in terms of these principles. Despite the large variety of detailed construction, there appear to be some basic principles, or combinations of basic principles, by which all seals function, these are presented and discussed. Theoretical and practical considerations in the application of these principles are discussed. Advantages, disadvantages, limitations, and application examples of various conventional and special seals are presented. Fundamental equations governing liquid and gas flows in thin film seals, which enable leakage calculations to be made, are also presented. Concept of flow functions, application of Reynolds lubrication equation, and nonlubrication equation flow, friction and wear; and seal lubrication regimes are explained.

  20. Behavior of primary coolant pump shaft seals during station blackout conditions

    Energy Technology Data Exchange (ETDEWEB)

    Hill, R.C.; Rhodes, D.B.

    1986-09-12

    An assessment is made of the ability of typical Reactor Coolant Pump (RCP) Shaft Seals to withstand the conditions predicted for a station blackout (loss of all alternating current power) at a nuclear power station. Several factors are identified that are key to seal stability including inlet fluid conditions, pressure downstream of the seal, and geometrical details of the seal rings. Limits for stable seal operation are determined for various combinations of these factors, and the conclusion is drawn that some RPC seals would be near the threshold of instability during a station blackout. If the threshold were exceeded, significant leakage of coolant from the primary coolant system could be expected.

  1. Parameters important to reactor coolant pump seal stability during station blackout

    Energy Technology Data Exchange (ETDEWEB)

    Hill, R.C.; Rhodes, D.B.

    1986-10-24

    An assessment is made of the ability of typical Reactor Coolant Pump (RCP) Shaft Seals to withstand the conditions predicted for a station blackout (loss of all alternating current power) at a nuclear power station. Several factors are identified that are key to seal stability including inlet fluid conditions, pressure downstream of the seal, and geometrical details of the seal rings. Limits for stable seal operation are determined for various combinations of these factors, and the conclusion is drawn that some RPC seals would be near or over the threshold of instability during a station blackout. If the threshold were exceeded, significant leakage of coolant from the primary coolant system could be expected.

  2. Bones and oil reservoirs : bioengineers use oilpatch technology to study fluid flow in bones

    Energy Technology Data Exchange (ETDEWEB)

    Marsters, S.

    2003-06-01

    The fact that porosity and the presence of channels are qualities that are common to oil reservoirs and bones, led to the use of reservoir modelling technology in investigating bone disorders and to the discovery of dramatic changes in the structure and blood supply of osteoarthritic bones that lie under degenerating cartilage. CMG (Computer Modelling Group) Ltd., developers of reservoir simulation software claim that their software packages can help with the modelling of cellular responses to strains and deformations that occur as fluid flows through bone after a traumatic event such as a tear in the anterior cruciate ligament, a common sports-related injury. Researchers at the University of Calgary expect that by looking at the changes in blood and fluid flow within the bone, they can attain a better understanding of the chain of events that leads to osteoarthritis. Better understanding of the progression of the disease could eventually lead to more precise administration of drugs to deal with osteoarthritic pain, and even to the prevention of painful arthritic joints.

  3. Repository seals requirements study

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-11-03

    The Yucca Mountain Site Characterization Project, managed by the Civilian Radioactive Waste Management System (CRWMS) Management and Operating Contractor (M and O) is conducting investigations to support the Viability Assessment and the License Application for a high-level nuclear waste repository at Yucca Mountain, Nevada. The sealing subsystem is part of the Yucca Mountain Waste Isolation System. The Yucca Mountain Site Characterization Project is currently evaluating the role of the sealing subsystem (shaft, ramp and exploratory borehole seals) in achieving the overall performance objectives for the Waste Isolation System. This report documents the results of those evaluations. This report presents the results of a repository sealing requirements study. Sealing is defined as the permanent closure of the shafts, ramps, and exploratory boreholes. Sealing includes those components that would reduce potential inflows above the repository, or that would divert flow near the repository horizon to allow vertical infiltration to below the repository. Sealing of such features as emplacement drifts was not done in this study because the current capability to calculate fracture flow into the drifts is not sufficiently mature. The objective of the study is to provide water or air flow performance based requirements for shafts, ramps, and exploratory boreholes located near the repository. Recommendations, as appropriate, are provided for developing plans, seals component testing, and other studies relating to sealing.

  4. Applications of quantum message sealing

    CERN Document Server

    Worley, G G

    2005-01-01

    In 2003, Bechmann-Pasquinucci introduced the concept of quantum seals, a quantum analogue to wax seals used to close letters and envelopes. Since then, some improvements on the method have been found. We first review the current quantum sealing techniques, then introduce and discuss potential applications of quantum message sealing, and conclude with some discussion of the limitations of quantum seals.

  5. The Application of the Supercritical Carbon Dioxide Fluid Extraction Technology on the Extraction of Micro Amount of Uranium

    Institute of Scientific and Technical Information of China (English)

    SONG; Zhi-jun; YU; Zhen; LIANG; Xiao-hu; DING; You-qian

    2012-01-01

    <正>The characteristic of solid radioactive wastes containing less 1% uranium, such as mine tailings, contaminated soil and sludge, is complex matrix and irregular surface. The traditional treatment technology usually consumes a lot of chemical reagents and produces a large amount of secondary wastes. The supercritical fluid has the advantage of high diffusivity, low viscosity, and liquid-like solvating capability, which enable the supercritical carbon dioxide fluid extraction (SFE) technology to be a alternative method to extract micro amount of uranium from solid radioactive wastes.

  6. High Test Peroxide High Sealing Conical Seal Project

    Data.gov (United States)

    National Aeronautics and Space Administration — High Test Peroxide (HTP) Highly Compatible High Sealing Conical Seals are necessary for ground test operations and space based applications. Current conical seals...

  7. Enhanced Wellbore Stabilization and Reservoir Productivity with Aphron Drilling Fluid Technology

    Energy Technology Data Exchange (ETDEWEB)

    Fred Growcock

    2004-03-31

    During this second Quarter of the Project, the first four tasks of Phase I--all focusing on the behavior of aphrons--were continued: (a) Aphron Visualization--evaluate and utilize various methods of monitoring and measuring aphron size distribution at elevated pressure; (b) Fluid Density--investigate the effects of pressure, temperature and chemical composition on the survivability of aphrons; (c) Aphron Air Diffusivity--determine the rate of loss of air from aphrons during pressurization; and (d) Pressure Transmissibility--determine whether aphron bridges created in fractures and pore throats reduce fracture propagation. The project team expanded the laboratory facilities and purchased a high-pressure system to measure bubble size distribution, a dissolved oxygen (DO) probe and computers for data acquisition. Although MASI Technologies LLC is not explicitly ISO-certified, all procedures are being documented in a manner commensurate with ISO 9001 certification, including equipment inventory and calibration, data gathering and reporting, chemical inventory and supplier data base, waste management procedures and emergency response plan. Several opportunities presented themselves to share the latest aphron drilling fluid technology with potential clients, including presentation of papers and working exhibit booths at the IADC/SPE Drilling Conference and the SPE Coiled Tubing Conference & Exhibition. In addition, a brief trip to the Formation Damage Symposium resulted in contacts for possible collaboration with ActiSystems, the University of Alberta and TUDRP/ACTS at the University of Tulsa. Preliminary results indicate that the Aphron Visualization and Pressure Transmissibility tasks should be completed on time. Although the Aphron Air Diffusivity task has been impeded by the lack of a suitable DO probe, it is hoped to be completed on time, too. The Fluid Density task, on the other hand, has had significant delays caused by faulty equipment and will likely require an

  8. An application of small-gap equations in sealing devices

    Science.gov (United States)

    Vionnet, Carlos A.; Heinrich, Juan C.

    1993-01-01

    The study of a thin, incompressible Newtonian fluid layer trapped between two almost parallel, sliding surfaces has been actively pursued in the last decades. This subject includes lubrication applications such as slider bearings or the sealing of non-pressurized fluids with rubber rotary shaft seals. In the present work we analyze numerically the flow of lubricant fluid through a micro-gap of sealing devices. The first stage of this study is carried out assuming that a 'small-gap' parameter delta attains an extreme value in the Navier-Stokes equations. The precise meaning of small-gap is achieved by the particular limit delta = 0 which, within the bounds of the hypotheses, predicts transport of lubricant through the sealed area by centrifugal instabilities. Numerical results obtained with the penalty function approximation in the finite element method are presented. In particular, the influence of inflow and outflow boundary conditions, and their impact in the simulated flow, are discussed.

  9. Tamper-indicating quantum optical seals

    Energy Technology Data Exchange (ETDEWEB)

    Humble, Travis S [ORNL; Williams, Brian P [ORNL

    2015-01-01

    Confidence in the means for identifying when tampering occurs is critical for containment and surveillance technologies. Fiber-optic seals have proven especially useful for actively surveying large areas or inventories due to the extended transmission range and flexible layout of fiber. However, it is reasonable to suspect that an intruder could tamper with a fiber-optic sensor by accurately replicating the light transmitted through the fiber. In this contribution, we demonstrate a novel approach to using fiber-optic seals for safeguarding large-scale inventories with increased confidence in the state of the seal. Our approach is based on the use of quantum mechanical phenomena to offer unprecedented surety in the authentication of the seal state. In particular, we show how quantum entangled photons can be used to monitor the integrity of a fiber-optic cable - the entangled photons serve as active sensing elements whose non-local correlations indicate normal seal operation. Moreover, we prove using the quantum no-cloning theorem that attacks against the quantum seal necessarily disturb its state and that these disturbances are immediately detected. Our quantum approach to seal authentication is based on physical principles alone and does not require the use of secret or proprietary information to ensure proper operation. We demonstrate an implementation of the quantum seal using a pair of entangled photons and we summarize our experimental results including the probability of detecting intrusions and the overall stability of the system design. We conclude by discussing the use of both free-space and fiber-based quantum seals for surveying large areas and inventories.

  10. Saving Seal Cutting

    Institute of Scientific and Technical Information of China (English)

    2009-01-01

    On April 20, the graduation ceremony of China’s seal-cutting art postgraduates and visiting experts from the Institute of Seal Cutting Art under the China Art Academy was held in Beijing. On the same day, the exhibition of the works of the teachers and graduates of the institute was also held.

  11. Apartment Compartmentalization With an Aerosol-Based Sealing Process

    Energy Technology Data Exchange (ETDEWEB)

    Maxwell, Sean [Consortium for Advanced Residential Buildings (CARB), Norwalk, CT (United States); Berger, David [Consortium for Advanced Residential Buildings (CARB), Norwalk, CT (United States); Harrington, Curtis [Univ. of California, Davis, CA (United States)

    2015-03-01

    The U.S. Department of Energy Building America Team, Consortium for Advanced Residential Buildings, sought to demonstrate this new technology application in a new construction multifamily building in Queens, New York. The effectiveness of the sealing process was evaluated by three methods: air leakage testing of overall apartment before-and-after sealing, point-source testing of individual leaks, and pressure measurements in the walls of an apartment during sealing.

  12. Three-step labyrinth seal for high-performance turbomachines

    Science.gov (United States)

    Hendricks, Robert C.

    1987-01-01

    A three-step labyrinth seal with 12, 11, and 10 labyrinth teeth per step, respectively, was tested under static (nonrotating) conditions. The configuration represented the seal for a high-performance turbopump (e.g., the space shuttle main engine fuel pump). The test data included critical mass flux and pressure profiles over a wide range of fluid conditions at concentric, partially eccentric, and fully eccentric seal positions. The seal mass fluxes (leakage rates) were lower over the entire range of fluid conditions tested than those for data collected for similar straight and three-step cylindrical seals, and this conformed somewhat to expectations. However, the pressure profiles for the eccentric positions indicated little, if any, direct stiffness for this configuration in contrast to significant direct stiffness reported for the straight and three-step cylindrical seals over the range of test conditions. Seal dynamics depend on geometric configuration, inlet and exit parameters, fluid phase, and rotation. The method of corresponding states was applied to the mass flux data, which were found to have a pressure dependency for helium.

  13. Hermetizing ability of the new obturating material for root canals «Real Seal» with «Resilon» technology

    Directory of Open Access Journals (Sweden)

    Makedonova Y.A.

    2012-03-01

    Full Text Available Simple, reliable and predictable obturation of root canals side by side with their cleaning and forming is an essential part of the endodontic treatment. The aim of this research is investigation of obturation density of root canals. Canals filled by means of lateral condensation of the new obturative system «Real Seal/Resilon» and by means of traditional method of canals obturation with the help of gutta-percha and sealer АН-plus. The results of the research proved a ligher hermetizing ability of the new experimental material «Real Seal» in comparison with obturation by means of gutta-percha pins. The obtained data reflects an objective picture and can be applied as a unique quality monitoring obturation of root canals.

  14. Three-step cylindrical seal for high-performance turbomachines

    Science.gov (United States)

    Hendricks, Robert C.

    1987-01-01

    A three-step cylindrical seal configuration representing the seal for a high performance turbopump (e.g., the space shuttle main engine fuel pump) was tested under static (nonrotating) conditions. The test data included critical mass flux and pressure profiles over a wide range of inlet temperatures and pressures for fluid nitrogen and fluid hydrogen with the seal in concentric and fully eccentric positions. The critical mass flux (leakage rate) was 70% that of an equivalent straight cylindrical seal with a correspondingly higher pressure drop based on the same flow areas of 0.3569 sq cm but 85% that of the straight seal based on the third-step flow area of 0.3044 sq cm. The mass flow rates for the three step cylindrical seal in the fully eccentric and concentric positions were essentially the same, and the trends in flow coefficient followed those of a simple axisymmetric inlet configuration. However, for inlet stagnation temperatures less than the thermodynamic critical temperature the pressure profiles exhibited a flat region throughout the third step of the seal, with the pressure magnitude dependent on the inlet stagnation temperature. Such profiles represent an extreme positive direct stiffness. These conditions engendered a crossover in the pressure profile upstream of the postulated choke that resulted in a local negative stiffness. Flat and crossover profiles resulting from choking within the seal are practically unknown to the seal designer. However, they are of critical importance to turbomachine stability and must be integrated into any dynamic analysis of a seal of this configuration. In addition, choking is highly dependent on geometry, inlet-to-backpressure ratio, and inlet temperature and can occur within the seal even though the backpressure is above the critical pressure.

  15. Elastic rubber seals and formed parts in motor car engineering and mechanical engineering. A practical review of the interactions between shape, material and working fluids; Dichtungstechnik mit gummielastischen Dichtungen und Formteilen im Fahrzeug- und Maschinenbau. Das Zusammenwirken von Bauformen, Werkstoffen und Betriebsstoffen - praxisnah dargestellt

    Energy Technology Data Exchange (ETDEWEB)

    Hoepke, E.; Barillas, G.; Braun, O.; Bayer, K.; Osen, E.; Struempel, H.J.

    2000-07-01

    The book describes basic types of seals and their requirements and applications, sealing materials and their performance in operation. PTFE is discussed at length, including its applications in hydraulic engineering. There are exemplary installations, a table of the most common working fluids, and a multitude of pictures. [German] Wer sich in Konstruktion, Produktion und Vertrieb oder beim Studium mit Dichtungen und Formteilen befasst, findet in diesem Buch eine rasche und wirksame Hilfe. Es geht weniger um die Beschreibung firmenspezifischer Bauformen, sondern um den richtigen Umgang mit den wichtigsten Grundformen der Dichtungen, den Dichtungswerkstoffen und deren Verhalten im Betrieb. Auch dem PTFE mit seinen ganz anderen Eigenschaften wird breiter Raum vor allem in der Hydraulik, gewaehrt. Einbaubeispiele, eine Uebersicht ueber die wichtigsten Betriebsstoffe, mit denen Dichtungen in Beruehrung kommen, und reichhaltige Bebilderung vermitteln einen raschen, umfassenden und weitgehend zeitlosen Ueberblick ueber die Dichtungstechnik. (orig.)

  16. Cryogenic fluid management technologies for space transportation. Zero G thermodynamic vent system

    Science.gov (United States)

    1994-01-01

    Long term storage of subcritical cryogens in space must address the problem of thermal stratification in the storage tanks, liquid acquisition devices, and associated feed systems. Due to the absence of gravity induced body forces, thermal stratification in zero-g is more severe than commonly experienced in a one-g environment. If left uncontrolled, the thermal gradients result in excessive tank pressure rise and the formation of undesirable liquid/vapor mixtures within the liquid bulk, liquid acquisition system, and propellant transfer lines. Since external heat leakage cannot be eliminated, a means of minimizing the thermal stratification in the ullage gas, liquid, and feed system is required. A subsystem which minimizes the thermal stratification and rejects the environmental heat leakage in an efficient manner is therefore needed for zero-g subcritical cryogenic systems. In ground based storage systems the ullage gas location is always known (top of the tank) and therefore direct venting of gases as a means of heat rejection is easily accomplished. In contrast, because the ullage location in a zero-g environment is not easily predictable, heat rejection through direct gaseous venting is difficult in space (requires liquid settling, or surface tension devices). A means of indirect venting through the use of a thermodynamic vent system (TVS) is therefore required. A thermodynamic vent system allows indirect venting of vapor through heat exchange between the vented fluid and the stored fluid. The objective is to ensure that only gas and not liquid is vented, in order to minimize the propellant losses. Consequently, the design of a TVS is a critical enabling technology for future applications such as solar thermal and electric propulsion, single-stage-to-orbit vertical landers and upper stages, and any space based operations involving subcritical cryogenics. To bridge this technology gap NASA MSFC initiated an effort to build and verify through ground tests a zero

  17. Low pressure cooling seal system for a gas turbine engine

    Science.gov (United States)

    Marra, John J

    2014-04-01

    A low pressure cooling system for a turbine engine for directing cooling fluids at low pressure, such as at ambient pressure, through at least one cooling fluid supply channel and into a cooling fluid mixing chamber positioned immediately downstream from a row of turbine blades extending radially outward from a rotor assembly to prevent ingestion of hot gases into internal aspects of the rotor assembly. The low pressure cooling system may also include at least one bleed channel that may extend through the rotor assembly and exhaust cooling fluids into the cooling fluid mixing chamber to seal a gap between rotational turbine blades and a downstream, stationary turbine component. Use of ambient pressure cooling fluids by the low pressure cooling system results in tremendous efficiencies by eliminating the need for pressurized cooling fluids for sealing this gap.

  18. Fluid Dynamic - Structural Interactions of Labyrinth Seals.

    Science.gov (United States)

    1986-08-01

    Linear rotor speeds comparable with the axial gap flow velocity, i.e., of the order of 100 m/sec. (d) Provision for controllable inlet flow swirl with...34Experimental Determination of Gap Flow -Conditioned Forces at Turbine Stages and Their Effect on the Running Stability of Simple Rotors". NASA TM

  19. STUDY ON RECIPROCATING SEALS FOR A LARGER DIAMETER AXIAL PISTON

    Institute of Scientific and Technical Information of China (English)

    Yang Jian; Yang Huayong; Xu Bing

    2004-01-01

    Sealing performance of the reciprocating seals on a larger diameter (100 mm in diameter ) axial piston is theoretically investigated.Based on the characteristics of the clearance flow between the seal and the piston, reasonable boundary conditions for Navier-Stokes equations are determined and the equations are modified, so that the final equations can describe the real flow state of the clearance flow.Through combining the final equations with finite element method, the pressure distributions within the clearance field during the reciprocating motion of the piston and the leakage rate with the pressure are studied.The deflections of the seal which affect sealing performance are calculated as well.Sealing performance of piston seals using oil as the working liquid is compared with using water.It is concluded that the seal using water as the working liquid is under dry friction, which cannot be dealt with the theory of fluid mechanics.The seal structure is only acceptable using oil as the working liquid..

  20. Rotordynamic and leakage characteristics of a 4-stage brush seal

    Science.gov (United States)

    Conner, K. J.; Childs, D. W.

    1992-12-01

    Experimental results are presented for the direct and cross-coupled stiffness and damping coefficients as well as the leakage performance for a 4-stage brush seal. Variable test parameters include the inlet pressure, pressure ratio, shaft speed, fluid prerotation, and seal spacing. Direct damping is shown to increase with running speed; otherwise, the rotordynamic coefficients are relatively insensitive to changes in the test parameters. Cross-coupled stiffness is generally unchanged by increasing the inlet tangential velocity to the seals, suggesting that the brush seal is not affected by inlet swirl. Direct stiffness is shown to increase with frequency; however, the magnitudes of direct stiffness are always positive. Cross-coupled stiffness increases slightly with frequency; yet not as drastically as direct stiffness. Comparisons of test results for the 4-stage brush seal with an 8-cavity labyrinth showed superior rotordynamics performance for the brush seal; viz., large values for direct stiffness and lower values for the (destabilizing) cross-coupled stiffness coefficient. The damping for brush seals is smaller, but comparable to labyrinth seals. The whirl-frequency ratio is always smaller for the brush seal.

  1. Sealing device for providing a seal in a turbomachine

    Science.gov (United States)

    Lacy, Benjamin Paul; Kottilingam, Srikanth Chandrudu; Porter, Christopher Donald; Schick, David Edward; Weber, David Wayne

    2016-08-16

    Sealing device for providing seals between adjacent components, and turbomachines utilizing such sealing devices, are provided. A sealing device includes a seal plate insertable between the adjacent components, the seal plate comprising a first face and an opposing second face. The sealing device further includes a plurality of pins extending from one of the first face or the second face, the plurality of pins configured to space the one of the first face or the second face from contact surfaces of the adjacent components.

  2. Nanoparticles in the pharmaceutical industry and the use of supercritical fluid technologies for nanoparticle production.

    Science.gov (United States)

    Sheth, Pratik; Sandhu, Harpreet; Singhal, Dharmendra; Malick, Waseem; Shah, Navnit; Kislalioglu, M Serpil

    2012-05-01

    Poor aqueous solubility of drug candidates is a major challenge for the pharmaceutical scientists involved in drug development. Particle size reduction appears as an effective and versatile option for solubility improvement. Nanonization is an attractive solution to improve the bioavailability of the poorly soluble drugs, improved therapies, in vivo imaging, in vitro diagnostics and for the production of biomaterials and active implants. In drug delivery, application of nanotechnology is commonly referred to as Nano Drug Delivery Systems (NDDS). In this article, commercially available nanosized drugs, their dosage forms and proprietors, as well as the methods used for preparation like milling, high pressure homogenization, vacuum deposition, and high temperature evaporation were listed. Unlike the traditional methods used for the particle size reduction, supercritical fluid-processing techniques offer advantages ranging from superior particle size control to clean processing. The primary focus of this review article is the use of supercritical CO2 based technologies for small particle generation. Particles that have the smooth surfaces, small particle size and distribution and free flowing can be obtained with particular SCF techniques. In almost all techniques, the dominating process variables may be thermodynamic and aerodynamic in nature, and the design of the particle collection environment. Rapid Expansion of Supercritical Solutions (RESS), Supercritical Anti Solvent (SAS) and Particles from Gas Saturated Solutions (PGSS) are three groups of processes which lead to the production of fine and monodisperse powders. Few of them may also control crystal polymorphism. Among the aforementioned processes, RESS involves dissolving a drug in a supercritical fluid (SCF) and passing it through an appropriate nozzle. Rapid depressurization of this solution causes an extremely rapid nucleation of the product. This process has been known for a long time but its application

  3. Laboratory Testing of Aerosol for Enclosure Air Sealing

    Energy Technology Data Exchange (ETDEWEB)

    Harrington, Curtis [Building Industry Research Alliance (BIRA), Stockton, CA (United States); Modera, Mark [Building Industry Research Alliance (BIRA), Stockton, CA (United States)

    2012-05-01

    This report presents a process for improving the air tightness of a building envelope by sealing shell leaks with an aerosol sealing technology. Both retrofit and new construction applications are possible through applying this process either in attics and crawlspaces or during rough-in stage.

  4. Factorial design in the spheronization of ibuprofen microparticulates using the rotor disk fluid-bed technology.

    Science.gov (United States)

    Chukwumezie, Beatrice Nkem; Wojcik, Mark; Malak, Paul; Damico, Frank; Adeyeye, Moji Christianah

    2004-01-01

    The aim of this study was to statistically evaluate the effects of some formulation and process variables in the spheronization of microparticulates of ibuprofen using the rotor disk fluid-bed technology and water as binder. Preliminary studies revealed that presence of surfactant, plate material type, and nature and content of binder influenced the process and quality of the spheronized material. A 2 x 2 x 3 full factorial randomized experiment was designed, demonstrating the influence of these factors on properties such as percent yield, particle size distribution, densities, ibuprofen release, moisture content, etc., as well as their interactions in the experimental response. A response known as the usable fraction was created representing microparticulates of 250 to 850 microm sizes (mesh size 20-60). The reproducibility of the spheronization process was assessed by blocking the experiments with the experiments within the blocks randomly replicated. The main effects included two binder levels (X1), two surfactant levels (X2), and a three-level plate type (X3) in which 2 two-level factors were collapsed into a single three-level factor. The results from the statistical analysis (general linear model, JMP 4) showed that the variables studied had a significant influence on most of the response variables evaluated (p experiments had no significant effect on the process and product characteristics analyzed, indicating the reproducibility of the process.

  5. Apartment Compartmentalization With an Aerosol-Based Sealing Process

    Energy Technology Data Exchange (ETDEWEB)

    Maxwell, S. [Consortium for Advanced Residential Buildings, Norwalk, CT (United States); Berger, D. [Consortium for Advanced Residential Buildings, Norwalk, CT (United States); Harrington, C. [Consortium for Advanced Residential Buildings, Norwalk, CT (United States)

    2015-03-01

    Air sealing of building enclosures is a difficult and time-consuming process. Current methods in new construction require laborers to physically locate small and sometimes large holes in multiple assemblies and then manually seal each of them. The innovation demonstrated under this research study was the automated air sealing and compartmentalization of buildings through the use of an aerosolized sealant, developed by the Western Cooling Efficiency Center at University of California Davis. CARB sought to demonstrate this new technology application in a multifamily building in Queens, NY. The effectiveness of the sealing process was evaluated by three methods: air leakage testing of overall apartment before and after sealing, point-source testing of individual leaks, and pressure measurements in the walls of the target apartment during sealing.

  6. Fur seal investigations, 1966

    Data.gov (United States)

    US Fish and Wildlife Service, Department of the Interior — Annually a report is made on the fur seal investigations carried on by the Bureau of Commercial Fisheries on the Pribilof Islands and at sea. Investigations on the...

  7. Bearded Seal Distribution Map

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — This dataset contains GIS layers that depict the known spatial distributions (i.e., ranges) of the two subspecies of bearded seals (Erignathus barbatus). It was...

  8. Spotted Seal Distribution Map

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — This dataset contains GIS layers that depict the known spatial distributions (i.e., ranges) and reported breeding areas of spotted seals (Phoca largha). It was...

  9. Ribbon Seal Distribution Map

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — This dataset contains GIS layers that depict the known spatial distributions (i.e., ranges) and reported breeding areas of ribbon seals (Histriophoca fasciata). It...

  10. Ringed Seal Distribution Map

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — This dataset contains GIS layers that depict the known spatial distributions (i.e., ranges) of the five subspecies of ringed seals (Phoca hispida). It was produced...

  11. Cutting fluids and clean technologies; Los fluidos de corte y las tecnologias limpias (III)

    Energy Technology Data Exchange (ETDEWEB)

    Terradillos, J.; Arnaiz, A.

    2003-07-01

    Metalworking fluids are an essential constituent of manufacturing and represent an important part of machining cost and disposal charges. Practically all cutting fluids currently in use fall into four categories: straight oils, soluble oils, semi-synthetic fluids and synthetic oils. The composition of these fluids depends on the machining requirements and primary functions include improving tool life, reducing thermal deformation of parts and improving surface finish and flushing away chips from the cutting zone. To maintain cutting fluid quality in the long term and, at the same time, reduce its environmental impact, three strategies could be followed: Prevention, Minimization and Evaluation, Related to prevention, different approaches exist for reducing the impact of cutting fluids. They include dry cutting, machining using a minimum quantity of lubricant (MQL) and developing environmental friendly acceptable formulations or refrigerant gases. (Author)

  12. Evaluation of seals for high-performance cryogenic turbomachines

    Science.gov (United States)

    Hendricks, R. C.; Tam, L. T.; Braun, M. J.; Vlcek, B. L.

    1987-01-01

    An approach to computing flow and dynamic characteristics for seals or bearings is discussed. The local average velocity was strongly influenced by inlet and exit effects and fluid injection, which in turn drove zones of secondary flow. For the restricted three-dimensional model considered, the integral averaged results were in reasonable agreement with selected data. Unidirectional pressure measurements alone were insufficient to define such flow variations. However, for seal and bearing leakage correlations the principles of corresponding states were found to be useful. Also discussed are three phenomena encountered during testing of three eccentric nonrotating seal configurations for the Space Shuttle Main Engine (SSME) Program. Fluid injection, choking within a seal, and pressure profile crossover are related to postulated zones of secondary flow or separation and to direct stiffness.

  13. Nuclear instrumentation cable end seal

    Science.gov (United States)

    Cannon, Collins P.; Brown, Donald P.

    1979-01-01

    An improved coaxial end seal for hermetically sealed nuclear instrumentation cable exhibiting an improved breakdown pulse noise characteristic under high voltage, high temperature conditions. A tubular insulator body has metallized interior and exterior surface portions which are braze sealed to a center conductor and an outer conductive sheath. The end surface of the insulator body which is directed toward the coaxial cable to which it is sealed has a recessed surface portion within which the braze seal material terminates.

  14. 染料敏化太阳能电池封装工艺的研究进展%Progress in Sealing Technology of Dye-Sensitized Solar Cells

    Institute of Scientific and Technical Information of China (English)

    黎颖; 杨峰; 程翠华; 赵勇

    2011-01-01

    染料敏化太阳能电池(Dye-sensitized solar cells,DSSC)作为第3代太阳能电池而受到广泛关注,但使用寿命短一直是制约DSSC进入实用阶段的主要因素之一.液态电解质的DSSC往往因为电解质挥发或渗漏而失效,因此封装工艺成为保障此类DSSC性能稳定和持久的重要手段.将DSSC相关技术中的封装环节独立出来,简述了近几年来DSSC封装工艺的进展.主要对小面积DSSC、大面积DSSC模块(包括柔性DSSC、可填充DSSC)和管状DSSC的封装材料和流程以及几种DSSC的性能特点进行阐述,对封装技术的发展方向以及应用提出了一些看法.%Dye-sensitized solar cells (DSSC) have attracted wide attention as the third generation solar cell. But the short useful life of DSSC is one of the main factors which limit DSSC to practical application. The liquid electrolyte which used in DSSC is easy to volatile or leak, therefore sealing is a key of DSSC to keep reliable durability and stability. The sealing is emphasized specially from the DSSC technology, including the classification, sealing process of small-size and the performance of high efficient DSSC, large-size DSSC module (such as flexible DSSC and rechargeable DSSC), tube-shape DSSC. The future development and application of DSSC are discussed.

  15. Preparation of Chitosan-Based Hemostatic Sponges by Supercritical Fluid Technology

    Directory of Open Access Journals (Sweden)

    Hu-Fan Song

    2014-03-01

    Full Text Available Using ammonium bicarbonate (AB particles as a porogen, chitosan (CS-based hemostatic porous sponges were prepared in supercritical carbon dioxide due to its low viscosity, small surface tension, and good compatibility with organic solvent. Fourier transform infrared spectroscopy (FTIR spectra demonstrated that the chemical compositions of CS and poly-(methyl vinyl ether-co-maleic anhydride (PVM/MA were not altered during the phase inversion process. The morphology and structure of the sponge after the supercritical fluid (SCF process were observed by scanning electron microscopy (SEM. The resulting hemostatic sponges showed a relatively high porosity (about 80% with a controllable pore size ranging from 0.1 to 200 µm. The concentration of PVM/MA had no significant influence on the porosity of the sponges. Comparative experiments on biological assessment and hemostatic effect between the resulting sponges and Avitene® were also carried out. With the incorporation of PVM/MA into the CS-based sponges, the water absorption rate of the sponges increased significantly, and the CS-PVM/MA sponges showed a similar water absorption rate (about 90% to that of Avitene®. The results of the whole blood clotting experiment and animal experiment also demonstrated that the clotting ability of the CS-PVM/MA sponges was similar to that of Avitene®. All these results elementarily verified that the sponges prepared in this study were suitable for hemostasis and demonstrated the feasibility of using SCF-assisted phase inversion technology to produce hemostatic porous sponges.

  16. Sliding seal for mining machine power transmission

    Energy Technology Data Exchange (ETDEWEB)

    Levenstein, V.M.

    1993-07-06

    A generally tubular sealing mechanism is described for use in the power train of a mining machine to seal between an annular seal face on one of two spaced apart units in the power train and a sealing ring surface on the other of said units for sealed protection of a drive shaft connected between said two units, said sealing mechanism including a tubular seal carrier with a first end portion having a cylindrical sealing surface for being telescoped with said sealing ring surface, an annular seal element mountable on said cylindrical sealing surface for sealing engagement between said sealing ring surface and said cylindrical sealing surface, said carrier further having a second end portion with a radially extending face, a clamp connectable between said one unit and said carrier for urging said radially extending face toward said annular seal face, and a sealing member mountable in sealing engagement between said annular seal face and said radially extending face.

  17. Water Gushing Mechanism and Grouting Sealing Technology of Vertical Shaft lining in Yiqiao Coal Mine%义桥煤矿立井井简涌水机理与注浆封堵技术

    Institute of Scientific and Technical Information of China (English)

    林东才; 魏夕合; 刘尊欣; 张培森

    2012-01-01

    针对义桥煤矿复杂水文地质条件下深厚表土层立井壁破裂、井筒涌水严重,采用单液及双液水泥、水玻璃多次封堵无效的技术难题,结合井壁破裂理论中的施工质量说和竖直附加应力说,分析了义桥煤矿主副立井井壁涌水特征及变形破坏机理,在此基础上,研究了高分子化学材料马丽散N注浆封堵涌水、加固围岩机理,并制定了主副井筒表土段壁间注浆、基岩段壁后注浆的钻孔布置与施工工艺,并对注浆量、注浆压力等进行了过程监控,对井筒涌水量进行了长期监测,实测涌水量已小于0.05m^3/h,达到了防治井壁破裂、封堵涌水、稳定含水层水压的目的,缓释和抑制了井壁附加压力。%According to the technical problem of mine shaft lining breaking, water gushing seriously in shaft, many invalid sealing of using single liquid and dual fluid cement and sodium silicate in the deep and thick topsoil under complex hydrogeology conditions of Yiqiao coal mine, combining with the construction quality hypothesis and the vertical additional stress hypothesis of the mine shaft lin- ing breaking theory, the water gushing characteristics and deformation failure mechanism of the main and auxiliary shaft were analyzed.And on this basis, grouting and blocking water gushing and reinforcement of surrounding rock mechanism of the high polymer chemistry material marithan N were studied, and the drill hole layout and the construction technology of grouting between borehole wall of topsoil section, grouting behind the wall of the bedrock section were formulated, and the process monitoring for the grouting quantity and grou- ting pressure were carried out. Through long - term monitoring of the shaft lining water gushing, the shaft lining water gushing was less than O. 05 m3/h, which realized the purpose of preventing and controlling of shaft lining water gushing, shaft lining breaking, stability of

  18. Evaluation of supercritical fluid technology as preparative technique of benzocaine-cyclodextrin complexes--comparison with conventional methods.

    Science.gov (United States)

    Al-Marzouqi, Ali H; Jobe, Baboucarr; Dowaidar, Ali; Maestrelli, Francesca; Mura, Paola

    2007-01-17

    The objective of this study was to investigate the effect of the preparation method on the physico-chemical properties of complexes prepared between beta-cyclodextrin (beta-Cyd) and benzocaine (BZC). In particular, the effectiveness of a new technique based on supercritical carbon dioxide (SC CO(2)) for preparing solid drug-cyclodextrin complexes was investigated and compared to other more conventional methods such as kneading (KN), co-evaporation (COE), co-grinding (GR) and sealed-heating (S.H.). Effects of temperature, pressure and exposure time on the properties of complexes prepared by SC CO(2) technology were also studied. The different systems were characterized by differential scanning calorimetry (DSC), Fourier transform infrared spectroscopy (FTIR), powder X-ray diffractometry (PXRD) and dissolution test according to the dispersed amount method. The co-grinding (GR) method resulted in amorphous products while other methods led to crystalline or partially amorphous products depending on both the method and its experimental conditions. SC CO(2) method revealed to be an effective technique for preparing solid systems between beta-cyclodextrin and benzocaine, avoiding the use of organic solvents (and problems of their complete removal) and allowing an easy scale-up of the process. As for the influence of the experimental conditions in promoting the solid-state drug-carrier interaction when using the SC CO(2) method, temperature seemed to play the major role, whereas pressure and exposure times had more limited effects. Dissolution tests confirmed a limited but favourable effect in increasing the exposure time, while indicated a possible interaction effect between temperature and pressure in influencing the dissolution performance of the final product. The best product obtained by the SC CO(2) method showed dissolution properties similar to those of the co-ground product and only slightly lower than the system obtained by sealed-heating, which was the most

  19. Space Shuttle Orbiter AFT heat shield seal

    Science.gov (United States)

    Walkover, L. J.

    1979-01-01

    The evolution of the orbiter aft heat shield seal (AHSS) design, which involved advancing mechanical seal technology in severe thermal environment is discussed. The baseline design, various improvements for engine access, and technical problem solution are presented. It is a structure and mechanism at the three main propulsion system (MPS) engine interfaces to the aft compartment structure. Access to each MPS engine requires disassembly and removal of the AHSS. Each AHSS accommodates the engine movement, is exposed to an extremely high temperature environment, and is part of the venting control of the aft compartment.

  20. THE ORIGINS OF SEALS AND SEALING IN CHINA

    Institute of Scientific and Technical Information of China (English)

    1994-01-01

    The origin of Chinese seals remains obscure in modern research. Most publications, influenced by the traditional point of view, have dealt with the seals handed down from the Eastern Zhou (771-256 B.C.). Only a few studies have discussed seals from their earliest-and still neglected-history. There have even been some suggestions, based on the idea of using a seal and using it on clay first developed in Mesopotamia, that the seal was introduced to China from the Near East. This proposed foreign origin makes the history of Chinese seals more complicated.

  1. Intracoronal sealing ability of two dental cements.

    Science.gov (United States)

    Wells, John D; Pashley, David H; Loushine, Robert J; Weller, R Norman; Kimbrough, W Frank; Pereira, Patricia N

    2002-06-01

    The purpose of this study was to compare the efficacy of sealing the coronal 2-mm of the root canals versus covering the entire pulpal floor with one of two dental-resin cements (Principle or C&B Metabond). Sixty-two molars with the occlusal half of the crowns and the apical half of the roots removed were used. Each canal was enlarged by using a #3 Gates Glidden bur and obturated with unsealed gutta-percha cones. The teeth were randomly assigned to four groups, each containing 15 teeth, plus a negative and a positive control. In group 1, 2 mm of Principle were placed over the entire pulpal floor. In group 2, Principle was placed 2 mm into each canal orifice. Groups 3 and 4 were the same as groups 1 and 2, except C&B Metabond cement was used. After the cement set, the gutta-percha was removed and the integrity of the seal was tested by fluid filtration at a pressure of 20 cm H2O at 1 h and at 1, 2, and 4 weeks. The data were analyzed by a three-way ANOVA and the Student-Newman-Keuls tests at alpha = 0.05. The controls behaved as expected. Results showed that there were no statistically significant differences among the materials used or the location (p > 0.05), but there was a significant difference with respect to time. Principle leaked significantly more than C&B Metabond at 1 h (p < 0.05), but the seal became tighter over time. C&B Metabond leaked less early (p < 0.05) but increased in leakage at 4 weeks. Both materials sealed well over the 4-week study. Principle was easier to use, and sealing the entire pulpal floor was easier than sealing only the canal orifice.

  2. Forged seal detection based on the seal overlay metric.

    Science.gov (United States)

    Lee, Joong; Kong, Seong G; Lee, Young-Soo; Moon, Ki-Woong; Jeon, Oc-Yeub; Han, Jong Hyun; Lee, Bong-Woo; Seo, Joong-Suk

    2012-01-10

    This paper describes a method for verifying the authenticity of a seal impression imprinted on a document based on the seal overlay metric, which refers to the ratio of an effective seal impression pattern and the noise in the neighborhood of the reference impression region. A reference seal pattern is obtained by taking the average of a number of high-quality impressions of a genuine seal. A target seal impression to be examined, often on paper with some background texts and lines, is segmented out from the background by an adaptive threshold applied to the histogram of color components. The segmented target seal impression is then spatially aligned with the reference by maximizing the count of matching pixels. Then the seal overlay metric is computed for the reference and the target. If the overlay metric of a target seal is below a predetermined limit for the similarity to the genuine, then the target is classified as a forged seal. To further reduce the misclassification rate, the seal overlay metric is adjusted by the filling rate, which reflects the quality of inked pattern of the target seal. Experiment results demonstrate that the proposed method can detect elaborate seal impressions created by advanced forgery techniques such as lithography and computer-aided manufacturing. Copyright © 2011 Elsevier Ireland Ltd. All rights reserved.

  3. Application and Progress of Research on Supercritical Fluid Extraction Technology%超临界萃取技术研究现状与应用

    Institute of Scientific and Technical Information of China (English)

    周也; 田震; 王丽雯

    2012-01-01

    Bac technology of extraction and kground of supercritical fluid extraction technology was introduced and overview of the supercritical fluid extraction was also introduced. Focused on the method of enhanced industrial applications of supercritical fluid extraction technology.%简要介绍了超临界萃取技术的背景,并对超临界萃取技术做相关概述。着重介绍了强化萃取的方法和超临界萃取技术的工业应用。

  4. Gas Analysis of Geothermal Fluid Inclusions: A New Technology For Geothermal Exploration

    Energy Technology Data Exchange (ETDEWEB)

    David I. Norman; Joseph Moore

    2004-03-09

    To increase our knowledge of gaseous species in geothermal systems by fluid inclusion analysis in order to facilitate the use of gas analysis in geothermal exploration. The knowledge of gained by this program can be applied to geothermal exploration, which may expand geothermal production. Knowledge of the gas contents in reservoir fluids can be applied to fluid inclusion gas analysis of drill chip cuttings in a similar fashion as used in the petroleum industry. Thus the results of this project may lower exploration costs both in the initial phase and lower drill hole completion costs. Commercial costs for fluid inclusion analysis done on at 20 feet intervals on chip samples for 10,000 ft oil wells is about $6,000, and the turn around time is a few weeks.

  5. HMSRP Hawaiian Monk Seal Master Identification Records (seal)

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — This data set contains records of all individually identified Hawaiian monk seals since 1981. These seals were identified by PSD personnel and cooperating scientists...

  6. Dynamic Characteristics of Flow Induced Vibration in a Rotor-Seal System

    Directory of Open Access Journals (Sweden)

    Nan Zhang

    2011-01-01

    Full Text Available Flow induced vibration is an important factor affecting the performance of the rotor-seal system. From the point of view of flow induced vibration, the nonlinear models of the rotor-seal system are presented for the analysis of the fluid force, which is induced by the interaction between the unstable fluid flow in the seal and the vibrating rotor. The nonlinear characteristics of flow induced vibration in the rotor-seal system are analyzed, and the nonlinear phenomena in the unbalanced rotor-seal system are investigated using the nonlinear models. Various nonlinear phenomena of flow induced vibration in the rotor-seal system, such as synchronization phenomenon and amplitude mutation, are reproduced.

  7. Pore-lining composition and capillary breakthrough pressure of mudstone caprocks : sealing efficiency at geologic CO2 storage sites.

    Energy Technology Data Exchange (ETDEWEB)

    Heath, Jason E.; Nemer, Martin B.; McPherson, Brian J. O. L. (University of Utah, Salt Lake City, UT); Dewers, Thomas A.; Kotula, Paul Gabriel

    2010-12-01

    Subsurface containment of CO2 is predicated on effective caprock sealing. Many previous studies have relied on macroscopic measurements of capillary breakthrough pressure and other petrophysical properties without direct examination of solid phases that line pore networks and directly contact fluids. However, pore-lining phases strongly contribute to sealing behavior through interfacial interactions among CO2, brine, and the mineral or non-mineral phases. Our high resolution (i.e., sub-micron) examination of the composition of pore-lining phases of several continental and marine mudstones indicates that sealing efficiency (i.e., breakthrough pressure) is governed by pore shapes and pore-lining phases that are not identifiable except through direct characterization of pores. Bulk X-ray diffraction data does not indicate which phases line the pores and may be especially lacking for mudstones with organic material. Organics can line pores and may represent once-mobile phases that modify the wettability of an originally clay-lined pore network. For shallow formations (i.e., < {approx}800 m depth), interfacial tension and contact angles result in breakthrough pressures that may be as high as those needed to fracture the rock - thus, in the absence of fractures, capillary sealing efficiency is indicated. Deeper seals have poorer capillary sealing if mica-like wetting dominates the wettability. We thank the U.S. Department of Energy's National Energy Technology Laboratory and the Office of Basic Energy Sciences, and the Southeast and Southwest Carbon Sequestration Partnerships for supporting this work.

  8. Static seal for turbine engine

    Science.gov (United States)

    Salazar, Santiago; Gisch, Andrew

    2014-04-01

    A seal structure for a gas turbine engine, the seal structure including first and second components located adjacent to each other and forming a barrier between high and low pressure zones. A seal cavity is defined in the first and second components, the seal cavity extending to either side of an elongated gap extending generally in a first direction between the first and second components. A seal member is positioned within the seal cavity and spans across the elongated gap. The seal member includes first and second side edges extending into each of the components in a second direction transverse to the first direction, and opposing longitudinal edges extending between the side edges generally parallel to the first direction. The side edges include a groove formed therein for effecting a reduction of gas flow around the seal member at the side edges.

  9. Low torque hydrodynamic lip geometry for bi-directional rotation seals

    Science.gov (United States)

    Dietle, Lannie L.; Schroeder, John E.

    2009-07-21

    A hydrodynamically lubricating geometry for the generally circular dynamic sealing lip of rotary seals that are employed to partition a lubricant from an environment. The dynamic sealing lip is provided for establishing compressed sealing engagement with a relatively rotatable surface, and for wedging a film of lubricating fluid into the interface between the dynamic sealing lip and the relatively rotatable surface in response to relative rotation that may occur in the clockwise or the counter-clockwise direction. A wave form incorporating an elongated dimple provides the gradual convergence, efficient impingement angle, and gradual interfacial contact pressure rise that are conducive to efficient hydrodynamic wedging. Skewed elevated contact pressure zones produced by compression edge effects provide for controlled lubricant movement within the dynamic sealing interface between the seal and the relatively rotatable surface, producing enhanced lubrication and low running torque.

  10. Ceramic to metal seal

    Energy Technology Data Exchange (ETDEWEB)

    Snow, Gary S. (Albuquerque, NM); Wilcox, Paul D. (Albuquerque, NM)

    1976-01-01

    Providing a high strength, hermetic ceramic to metal seal by essentially heating a wire-like metal gasket and a ceramic member, which have been chemically cleaned, while simultaneously deforming from about 50 to 95 percent the metal gasket against the ceramic member at a temperature of about 30 to 75 percent of the melting temperature of the metal gasket.

  11. GOLD PRESSURE VESSEL SEAL

    Science.gov (United States)

    Smith, A.E.

    1963-11-26

    An improved seal between the piston and die member of a piston-cylinder type pressure vessel is presented. A layer of gold, of sufficient thickness to provide an interference fit between the piston and die member, is plated on the contacting surface of at least one of the members. (AEC)

  12. Mechanical Face Seal Dynamics.

    Science.gov (United States)

    1985-12-01

    These liquids range from lubricants to highly toxic chemicals and acids. The applications range from helicopter transmissions to nuclear reactor... Analit ~is., N ,iontat ting lame St-ak"ts fnn. ASXIE namin Behaioir ni Nonmmuiam ing (knied-Fate Mechanikal Seals:* SL /I ub In h. 104. 1. 111 *)6ii-414

  13. Detection of grey seal

    NARCIS (Netherlands)

    van Bleijswijk, J.; Begeman, L.; Witte, H.J.; IJsseldijk, L.L.; Brasseur, S.M.J.M.; Gröne, A.; Leopold, M.F.

    2014-01-01

    DNA was analysed from external wounds on 3 dead harbour porpoises Phocoena phocoena that were stranded in the Netherlands. Puncture wounds as well as the edges of large open wounds were sampled with sterile cotton swabs. With specific primers that target the mtDNA control region of grey seal Halicho

  14. Detection of grey seal

    NARCIS (Netherlands)

    van Bleijswijk, J.; Begeman, L.; Witte, H.J.; IJsseldijk, L.L.; Brasseur, S.M.J.M.; Gröne, A.; Leopold, M.F.

    2014-01-01

    DNA was analysed from external wounds on 3 dead harbour porpoises Phocoena phocoena that were stranded in the Netherlands. Puncture wounds as well as the edges of large open wounds were sampled with sterile cotton swabs. With specific primers that target the mtDNA control region of grey seal

  15. Comparative Analysis of Technologies for Quantifying Extracellular Vesicles (EVs in Clinical Cerebrospinal Fluids (CSF.

    Directory of Open Access Journals (Sweden)

    Johnny C Akers

    Full Text Available Extracellular vesicles (EVs have emerged as a promising biomarker platform for glioblastoma patients. However, the optimal method for quantitative assessment of EVs in clinical bio-fluid remains a point of contention. Multiple high-resolution platforms for quantitative EV analysis have emerged, including methods grounded in diffraction measurement of Brownian motion (NTA, tunable resistive pulse sensing (TRPS, vesicle flow cytometry (VFC, and transmission electron microscopy (TEM. Here we compared quantitative EV assessment using cerebrospinal fluids derived from glioblastoma patients using these methods. For EVs 150 nm in diameter, NTA consistently detected lower number of EVs relative to TRPS. These results unveil the strength and pitfalls of each quantitative method alone for assessing EVs derived from clinical cerebrospinal fluids and suggest that thoughtful synthesis of multi-platform quantitation will be required to guide meaningful clinical investigations.

  16. Formulating food protein-stabilized indomethacin nanosuspensions into pellets by fluid-bed coating technology: physical characterization, redispersibility, and dissolution

    Directory of Open Access Journals (Sweden)

    He W

    2013-08-01

    Full Text Available Wei He,1,2 Yi Lu,1 Jianping Qi,1 Lingyun Chen,3 Lifang Yin,2 Wei Wu1 1School of Pharmacy, Fudan University, Key Laboratory of Smart Drug Delivery of Ministry of Education and PLA, Shanghai, 2Department of Pharmaceutics, School of Pharmacy, China Pharmaceutical University, Nanjing, Jiangsu, People's Republic of China; 3Department of Agricultural, Food and Nutritional Sciences, University of Alberta, Edmonton, AB, Canada Background: Drug nanosuspensions are very promising for enhancing the dissolution and bioavailability of drugs that are poorly soluble in water. However, the poor stability of nanosuspensions, reflected in particle growth, aggregation/agglomeration, and change in crystallinity state greatly limits their applications. Solidification of nanosuspensions is an ideal strategy for addressing this problem. Hence, the present work aimed to convert drug nanosuspensions into pellets using fluid-bed coating technology. Methods: Indomethacin nanosuspensions were prepared by the precipitation-ultrasonication method using food proteins (soybean protein isolate, whey protein isolate, ß-lactoglobulin as stabilizers. Dried nanosuspensions were prepared by coating the nanosuspensions onto pellets. The redispersibility, drug dissolution, solid-state forms, and morphology of the dried nanosuspensions were evaluated. Results: The mean particle size for the nanosuspensions stabilized using soybean protein isolate, whey protein isolate, and β-lactoglobulin was 588 nm, 320 nm, and 243 nm, respectively. The nanosuspensions could be successfully layered onto pellets with high coating efficiency. Both the dried nanosuspensions and nanosuspensions in their original amorphous state and not influenced by the fluid-bed coating drying process could be redispersed in water, maintaining their original particle size and size distribution. Both the dried nanosuspensions and the original drug nanosuspensions showed similar dissolution profiles, which were both much

  17. Emotion-on-a-chip (EOC): evolution of biochip technology to measure human emotion using body fluids.

    Science.gov (United States)

    Lee, Jung-Hyun; Hwang, Yoosun; Cheon, Keun-Ah; Jung, Hyo-Il

    2012-12-01

    Recent developments in nano/micro technology have made it possible to construct small-scale sensing chips for the analysis of biological markers such as nucleic acids, proteins, small molecules, and cells. Although biochip technology for the diagnosis of severe physiological diseases (e.g., cancer, diabetes, and cardiovascular disease) has been extensively studied, biochips for the monitoring of human emotions such as stress, fear, depression, and sorrow have not yet been introduced, and the development of such a biochip is in its infancy. Emotion science (or affective engineering) is a rapidly expanding engineering/scientific discipline that has a major impact on human society. The growing interest in the integration of emotion science and engineering is a result of the recent trend of merging various academic fields. In this paper we discuss the potential importance of biochip technology in which human emotion can be precisely measured in real time using body fluids such as blood, saliva, urine, or sweat. We call these biochips emotion-on-a-chip (EOC). The EOC system consists of four parts: (1) collection of body fluids, (2) separation of emotional markers, (3) detection of optical or electrical signals, and (4) display of results. These techniques provide new opportunities to precisely investigate human emotion. Future developments in EOC techniques will combine social and natural sciences to expand their scope of study. Copyright © 2012 Elsevier Ltd. All rights reserved.

  18. Moisture-proof & Anti-rust Sealing and Packing Technology for Exciters′Package%励磁机防潮防锈的密封包装技术

    Institute of Scientific and Technical Information of China (English)

    曹颖; 李建洲; 董宏达

    2015-01-01

    励磁机是汽轮发电机设备上的重要产品之一,在出厂发运前对励磁机须采取防潮、防锈的密封包装。文章介绍如何采取措施确保励磁机在长时间的运输和储存过程中安全、可靠,不发生金属结构锈蚀和绝缘受潮等不良现象。%The exciter was one of the important pro-ducts of turbo-generator. It was necessary to take mois-ture-proof and anti-rust sealing & packing treatment for the exciter before shipment to guarantee the exciter safety during the long-time transportation and storage and elim-inate such unhealthy tendency as corrosion on the metal structure and moisture on the insulation parts.

  19. Basis of property limits for inflatable seal fluoroelastomers

    Energy Technology Data Exchange (ETDEWEB)

    Sinha, N.K., E-mail: nksinha@igcar.gov.in [Indira Gandhi Centre for Atomic Research (IGCAR), Department of Atomic Energy (DAE), Kalpakkam, Tamilnadu 603102 (India); Raj, Baldev, E-mail: dr.baldev@psg.org.in [Indira Gandhi Centre for Atomic Research (IGCAR), Department of Atomic Energy (DAE), Kalpakkam, Tamilnadu 603102 (India)

    2012-03-15

    Identification of a set of governing physico-mechanical properties for inflatable seals of Prototype Fast Breeder Reactor (PFBR) and specification of their limits is described based on operating requirements, design practices and results from seal development. The limits of tensile strength, elongation at break, hardness, tear strength, fluid compatibility, compression set and specific gravity defined for the Viton GBL 200S/600S based inflatable seal formulation provide a standardized framework for regular production of reactor seals and a streamlined approach for compounding, design, manufacture and quality control. This assures significant reduction of efforts during the envisaged unification of Fast Breeder Reactor sealing based on four variations of inflatable seal compound which could result in a universal design code apart from significant gains in safety, reliability and life. The property set has potential use in Pressurized Heavy Water Reactor and Advanced Heavy Water Reactor. Inclusion of factors such as batch-to-batch variations of compound properties and their reproducibility during laboratory measurements, hot tensile behavior of fluoroelastomer, long term ageing effects and the margin of safety at the end of seal design life ensures the utility of property set in attaining its intended objective.

  20. Brush Seal Arrangement for the RS-68 Turbopump Set

    Science.gov (United States)

    Nunez, D.; Ransom, D.; Prueger, G.

    2006-01-01

    The nature of the RS-68 turbopumps requires that the hydrogen seals separating the pump from the turbine must have extremely low levels of leakage and be contained in small packages. Conventional seal technologies are not able to reasonably satisfy such design requirements. A review of experimental measurements and analysis publications suggests that brush seals are well suited for the design requirements. Brush seals are shown to have less leakage than conventional labyrinth and damper seals and have no adverse effects on the rotordynamics of the machine. The bulk-flow analysis presented by Hendricks et al. is used as a guideline to create a spreadsheet that provides mass flow through the seal and heat generated by the rubbing contact of the bristles on the shaft. The analysis is anchored to published data for LN2 and LH2 leakage tests. Finally, the analysis is used to design seals for both applications. It is observed that the most important analysis parameter is the thickness of the bristle pack and its relationship to seal clearance, lay angle and pressure drop.

  1. Investigate the complex process in particle-fluid based surface generation technology using reactive molecular dynamics method

    Science.gov (United States)

    Han, Xuesong; Li, Haiyan; Zhao, Fu

    2017-07-01

    Particle-fluid based surface generation process has already become one of the most important materials processing technology for many advanced materials such as optical crystal, ceramics and so on. Most of the particle-fluid based surface generation technology involves two key process: chemical reaction which is responsible for surface softening; physical behavior which is responsible for materials removal/deformation. Presently, researchers cannot give a reasonable explanation about the complex process in the particle-fluid based surface generation technology because of the small temporal-spatial scale and the concurrent influence of physical-chemical process. Molecular dynamics (MD) method has already been proved to be a promising approach for constructing effective model of atomic scale phenomenon and can serve as a predicting simulation tool in analyzing the complex surface generation mechanism and is employed in this research to study the essence of surface generation. The deformation and piles of water molecule is induced with the feeding of abrasive particle which justifies the property mutation of water at nanometer scale. There are little silica molecule aggregation or materials removal because the water-layer greatly reduce the strength of mechanical interaction between particle and materials surface and minimize the stress concentration. Furthermore, chemical effect is also observed at the interface: stable chemical bond is generated between water and silica which lead to the formation of silconl and the reaction rate changes with the amount of water molecules in the local environment. Novel ring structure is observed in the silica surface and it is justified to be favored of chemical reaction with water molecule. The siloxane bond formation process quickly strengthened across the interface with the feeding of abrasive particle because of the compressive stress resulted by the impacting behavior.

  2. Investigate the complex process in particle-fluid based surface generation technology using reactive molecular dynamics method

    Directory of Open Access Journals (Sweden)

    Xuesong Han

    2017-07-01

    Full Text Available Particle-fluid based surface generation process has already become one of the most important materials processing technology for many advanced materials such as optical crystal, ceramics and so on. Most of the particle-fluid based surface generation technology involves two key process: chemical reaction which is responsible for surface softening; physical behavior which is responsible for materials removal/deformation. Presently, researchers cannot give a reasonable explanation about the complex process in the particle-fluid based surface generation technology because of the small temporal-spatial scale and the concurrent influence of physical-chemical process. Molecular dynamics (MD method has already been proved to be a promising approach for constructing effective model of atomic scale phenomenon and can serve as a predicting simulation tool in analyzing the complex surface generation mechanism and is employed in this research to study the essence of surface generation. The deformation and piles of water molecule is induced with the feeding of abrasive particle which justifies the property mutation of water at nanometer scale. There are little silica molecule aggregation or materials removal because the water-layer greatly reduce the strength of mechanical interaction between particle and materials surface and minimize the stress concentration. Furthermore, chemical effect is also observed at the interface: stable chemical bond is generated between water and silica which lead to the formation of silconl and the reaction rate changes with the amount of water molecules in the local environment. Novel ring structure is observed in the silica surface and it is justified to be favored of chemical reaction with water molecule. The siloxane bond formation process quickly strengthened across the interface with the feeding of abrasive particle because of the compressive stress resulted by the impacting behavior.

  3. Research on Specialized Computational Methods for Fluid-Structure Interaction Simulations for Advanced Submarine Technology

    Science.gov (United States)

    1992-05-01

    Symposium, Stellenbosch, South Africa , June 24-27, 1991. Oden, J.T., "Toward Optimal Control in Computational Fluid Dynamics: Smart Algorithms and Adaptive...B = Pib m (k) (6.5)d H k ) (k a ) d(kr) - where Jm is Bessel function of the first kind of order m, a is the radius of the cylinder, and bo = 1 and

  4. Assessing the mechanical impact of CO2 injection on faults and seals

    NARCIS (Netherlands)

    Orlic, B.

    2009-01-01

    Two options for geological storage of CO2 are currently considered: storage in depleted hydrocarbon fields, which have a hydrocarbon proven seal, and storage in deep (>800m) saline aquifers, which lack such a seal. Pore pressure changes resulting from fluid extraction and subsequent CO2 injection in

  5. Regenerator cross arm seal assembly

    Science.gov (United States)

    Jackman, Anthony V.

    1988-01-01

    A seal assembly for disposition between a cross arm on a gas turbine engine block and a regenerator disc, the seal assembly including a platform coextensive with the cross arm, a seal and wear layer sealingly and slidingly engaging the regenerator disc, a porous and compliant support layer between the platform and the seal and wear layer porous enough to permit flow of cooling air therethrough and compliant to accommodate relative thermal growth and distortion, a dike between the seal and wear layer and the platform for preventing cross flow through the support layer between engine exhaust and pressurized air passages, and air diversion passages for directing unregenerated pressurized air through the support layer to cool the seal and wear layer and then back into the flow of regenerated pressurized air.

  6. Carbon Dioxide Sealing Capacity: Textural or Compositional Controls?

    Energy Technology Data Exchange (ETDEWEB)

    Cranganu, Constantin; Soleymani, Hamidreza; Sadiqua, Soleymani; Watson, Kieva

    2013-11-30

    This research project is aiming to assess the carbon dioxide sealing capacity of most common seal-rocks, such as shales and non-fractured limestones, by analyzing the role of textural and compositional parameters of those rocks. We hypothesize that sealing capacity is controlled by textural and/or compositional pa-rameters of caprocks. In this research, we seek to evaluate the importance of textural and compositional parameters affecting the sealing capacity of caprocks. The conceptu-al framework involves two testable end-member hypotheses concerning the sealing ca-pacity of carbon dioxide reservoir caprocks. Better understanding of the elements controlling sealing quality will advance our knowledge regarding the sealing capacity of shales and carbonates. Due to relatively low permeability, shale and non-fractured carbonate units are considered relatively imper-meable formations which can retard reservoir fluid flow by forming high capillary pres-sure. Similarly, these unites can constitute reliable seals for carbon dioxide capture and sequestration purposes. This project is a part of the comprehensive project with the final aim of studying the caprock sealing properties and the relationship between microscopic and macroscopic characteristics of seal rocks in depleted gas fields of Oklahoma Pan-handle. Through this study we examined various seal rock characteristics to infer about their respective effects on sealing capacity in special case of replacing reservoir fluid with super critical carbon dioxide (scCO{sub 2}). To assess the effect of textural and compositional properties on scCO{sub 2} maximum reten-tion column height we collected 30 representative core samples in caprock formations in three counties (Cimarron, Texas, Beaver) in Oklahoma Panhandle. Core samples were collected from various seal formations (e.g., Cherokee, Keys, Morrowan) at different depths. We studied the compositional and textural properties of the core samples using several techniques

  7. Seals Having Textured Portions for Protection in Space Environments

    Science.gov (United States)

    Daniels, Christopher (Inventor); Garafolo, Nicholas (Inventor)

    2016-01-01

    A sealing construct for a space environment includes a seal-bearing object, a seal on the seal-bearing object, and a seal-engaging object. The seal includes a seal body having a sealing surface, and a textured pattern at the sealing surface, the textured pattern defining at least one shaded channel surface. The seal-engaging object is selectively engaged with the seal-bearing object through the seal. The seal-engaging object has a sealing surface, wherein, when the seal-engaging object is selectively engaged with the seal-bearing object, the sealing surface of the seal-engaging object engages the sealing surface of the seal, and the seal is compressed between the seal-bearing object and the seal-engaging object such that at least one shaded channel surface engages the sealing surface of the seal-engaging object.

  8. REDOX Technology for metal working fluids treatment: lifetime; Tecnologia REDOX aplicada al tratamiento de fluidos de corte: alargamiento de su vida util

    Energy Technology Data Exchange (ETDEWEB)

    Perez de Mendiola, A.; Villaran, M. C.; Valle, B.

    2001-07-01

    Metalworking fluids play a key role in industrial production engineering, because without them it would not be possible to make full use of the capabilities of modern machine tools. Nowadays, these fluids contain harmful substances. They are classified like dangerous wastes at the end of their life and have to be properly managed. On the other hand, the change of these fluids supposes additional costs: new fluid, production break, manpower for cleaning and waste management. Considering above mentioned, it is necessary to lengthen the metalworking fluid's life. LEIA and TEMA have developed a new system based on the redox technology that allows lengthen the metalworking fluid's life without bactericides and other chemical products. In this article we show the results obtained with this new system in an industrial plant of machinery manufacture. (Author) 8 refs.

  9. Birch Bark Dry Extract by Supercritical Fluid Technology: Extract Characterisation and Use for Stabilisation of Semisolid Systems

    Directory of Open Access Journals (Sweden)

    Markus Armbruster

    2017-03-01

    Full Text Available Triterpene compounds like betulin, betulinic acid, erythrodiol, oleanolic acid and lupeol are known for many pharmacological effects. All these substances are found in the outer bark of birch. Apart from its pharmacological effects, birch bark extract can be used to stabilise semisolid systems. Normally, birch bark extract is produced for this purpose by extraction with organic solvents. Employing supercritical fluid technology, our aim was to develop a birch bark dry extract suitable for stabilisation of lipophilic gels with improved properties while avoiding the use of toxic solvents. With supercritical carbon dioxide, three different particle formation methods from supercritical solutions have been tested. First, particle deposition was performed from a supercritical solution in an expansion chamber. Second, the Rapid Expansion of Supercritical Solutions (RESS method was used for particle generation. Third, a modified RESS-procedure, forming the particles directly into the thereby gelated liquid, was developed. All three methods gave yields from 1% to 5.8%, depending on the techniques employed. The triterpene composition of the three extracts was comparable: all three gave more stable oleogels compared to the use of an extract obtained by organic solvent extraction. Characterizing the rheological behaviour of these gels, a faster gelling effect was seen together with a lower concentration of the extract required for the gel formation with the supercritical fluid (SCF-extracts. This confirms the superiority of the supercritical fluid produced extracts with regard to the oleogel forming properties.

  10. Sealing the Mitochondrial Respirasome

    OpenAIRE

    Winge, Dennis R.

    2012-01-01

    The mitochondrial respiratory chain is organized within an array of supercomplexes that function to minimize the generation of reactive oxygen species (ROS) during electron transfer reactions. Structural models of supercomplexes are now known. Another recent advance is the discovery of non-OXPHOS complex proteins that appear to adhere to and seal the individual respiratory complexes to form stable assemblages that prevent electron leakage. This review highlights recent advances in our underst...

  11. A sealing element

    Energy Technology Data Exchange (ETDEWEB)

    Obi, F.; Takada, K.

    1983-09-22

    A sealing lining made of a mixture of polyethylene or polypropylene with an additive which prevents destruction of the lining is used in the element. The content of the additive in the mixture is 10 to 30 percent by mass. The additive basically consists of polyethylene. Carboxyl groups are introduced into the polymer as an anion and sodium, potassium and molybdenum are introduced as the cation.

  12. Laboratory Testing of Aerosol for Enclosure Air Sealing

    Energy Technology Data Exchange (ETDEWEB)

    Harrington, C.; Modera, M.

    2012-05-01

    Space conditioning energy use can be significantly reduced by addressing uncontrolled infiltration and exfiltration through the envelope of a building. A process for improving the air tightness of a building envelope by sealing shell leaks with an aerosol sealing technology is presented. Both retrofit and new construction applications are possible through applying this process either in attics and crawlspaces or during rough-in stage.

  13. REVIEW OF THE DISCHARGE, HEAT TRANSFER AND ROTORDYNAMIC CHARACTERISTICS OF HONEYCOMB SEALS%蜂窝密封内流动传热及转子动力特性的研究进展

    Institute of Scientific and Technical Information of China (English)

    晏鑫; 李军; 丰镇平

    2011-01-01

    The honeycomb seals were widely applied in turbomachinery industries due to their excellent rotordynamic and controlling leakage performance.State of the art on the discharge behavior, heat transfer and rotordynamic characteristics of honeycomb seal was reviewed based on the experimental tests, numerical simulations and theoretical analysis.Firstly, the leakage flow characteristics of the honeycomb seal and corresponding sealing mechanisms were introduced.The fluid-heat conjugate of discharge and total temperature increase, including heat transfer performance of the honeycomb seal was illustrated.The fluid-structure interaction mechanisms due to unsteady leakage flow excitation and rotordynamic characteristics of honeycomb seal was summarized.Finally, the research and development of honeycomb seals for advanced turbomachinery design technology were briefly presented.%蜂窝密封由于其具有优良的密封性能和转子动力特性而广泛应用于叶轮机械中.本文从实验研究、数值模拟和理论分析3个方面对蜂窝密封的研究现状及其进展进行了综述.主要内容包括:蜂窝密封泄漏特性及其密封机理的研究进展;蜂窝密封流动总温升特性的研究进展;蜂窝密封流热耦合作用下的流动传热特性研究进展;蜂窝密封非定常气流激振和转子动力特性的流固耦合机理研究进展.最后在蜂窝密封研究现状综述的基础上,展望了蜂窝密封的发展方向.

  14. Closure and Sealing Design Calculation

    Energy Technology Data Exchange (ETDEWEB)

    T. Lahnalampi; J. Case

    2005-08-26

    The purpose of the ''Closure and Sealing Design Calculation'' is to illustrate closure and sealing methods for sealing shafts, ramps, and identify boreholes that require sealing in order to limit the potential of water infiltration. In addition, this calculation will provide a description of the magma that can reduce the consequences of an igneous event intersecting the repository. This calculation will also include a listing of the project requirements related to closure and sealing. The scope of this calculation is to: summarize applicable project requirements and codes relating to backfilling nonemplacement openings, removal of uncommitted materials from the subsurface, installation of drip shields, and erecting monuments; compile an inventory of boreholes that are found in the area of the subsurface repository; describe the magma bulkhead feature and location; and include figures for the proposed shaft and ramp seals. The objective of this calculation is to: categorize the boreholes for sealing by depth and proximity to the subsurface repository; develop drawing figures which show the location and geometry for the magma bulkhead; include the shaft seal figures and a proposed construction sequence; and include the ramp seal figure and a proposed construction sequence. The intent of this closure and sealing calculation is to support the License Application by providing a description of the closure and sealing methods for the Safety Analysis Report. The closure and sealing calculation will also provide input for Post Closure Activities by describing the location of the magma bulkhead. This calculation is limited to describing the final configuration of the sealing and backfill systems for the underground area. The methods and procedures used to place the backfill and remove uncommitted materials (such as concrete) from the repository and detailed design of the magma bulkhead will be the subject of separate analyses or calculations. Post

  15. Theoretical aspects of non-newtonian fluids flow simulation in food technologies

    Directory of Open Access Journals (Sweden)

    E. Biletskii

    2015-05-01

    Full Text Available Introduction. The problems of simulating viscoplastic longitudinal and cross-sectional flow of non-Newtonian fluids are overviewed. Materials and methods. For the first time the superposition method by expressing the components of the stress tensor for building flow fields with higher dimension from flow fields with lower dimension with various boundary conditions when rheological parameters change depending on pressure was used. The flows in the channel are categorized by velocity and pressure values in each point of the section. Results.The theoretical methods for simulating flows of non-Newtonian fluids in channels of different geometry with moving bounds and pressure drop on channel edges with respect to functional connections between main process parameters are described using the superposition method. It is shown that longitudinal and cross-sectional are reduced to the collection of one-dimensional longitudinal flows of the same type which allow to describe three-dimensional isothermal in rectangular channel and two-dimensional flows in flat channels with different channel aspect ratio. The received theoretical two- and three-dimensional model of viscous flows in channels with basic geometry allow to research main regularities of the process and to establish optimal macro-kinetic and macro-dynamic flow characteristics of non-Newtonian materials which are aimed at reducing energy costs and material consumption of food processing equipment. Conclusion.The developed and theoretically reasonable three-dimensional models flows of non-Newtonian fluids in channels allow to perform qualitatively new design of food processing equipment which allows to reduce energy costs and material consumption.

  16. An Analysis of the Sealing Mechanism of a Soft-Packed Stuffing-Box Seal%软填料密封机理分析

    Institute of Scientific and Technical Information of China (English)

    宋鹏云

    2000-01-01

    The soft-packed stuffing-box seal with a long history is simple and still widely used, but it is still not very clear that as how the sealed fluid flows through the seal and what the real sealing mechanism is . This paper presents a fundamental analysis to the leaking mechanism of the sealed fluid leaking, and the fundamental requirements in order to make the seal be with good performance. It also clarifies some obscure concepts of the sealing mechanism of a soft-packed stuffing-box seal.%软填料密封结构简单,历史悠久而应用广泛,但对被密封流体通过软填料密封的泄漏机理和软填料密封的密封机理并没有完全认识清楚。本文初步分析了流体通过软填料密封的泄漏机理和使软填料密封具有良好密封性能的基本要求,并澄清了有关软填料密封机理的一些模糊认识。

  17. Straight cylindrical seal for high-performance turbomachines

    Science.gov (United States)

    Hendricks, Robert C.

    1987-01-01

    A straight cylindrical seal configuration representing the seal for a high-performance turbopump (e.g., the space shuttle main engine fuel pump) was tested under static (nonrotating) conditions. The test data included critical mass flux and pressure profiles over a wide range of inlet temperatures and pressures for fluid nitrogen and fluid hydrogen with the seal in concentric and fully eccentric positions. The critical mass fluxes (or leakage rates) for the concentric and fully eccentric configurations were nearly the same when based on stagnation conditions upstream of the seal. The fully eccentric configuration pressure profiles of the gas and liquid were different. Further, the pressure differences between the maximum and the minimum clearance positions were highly dependent on the geometric conditions, the temperature, and the absolute pressure at both the inlet and the exit. The pressure differences were greatest in the inlet region. The results, although complex, tend to follow the corresponding-states principles for critical flows. Gaseous injection near the seal exit plane significantly altered the pressure profiles and could be used to control turbomachine instabilities.

  18. Technologies for the removal of phenol from fluid streams: a short review of recent developments.

    Science.gov (United States)

    Busca, Guido; Berardinelli, Silvia; Resini, Carlo; Arrighi, Laura

    2008-12-30

    The available technologies for the abatement of phenol from water and gaseous streams are briefly reviewed, and the recent advancements summarized. Separation technologies such as distillation, liquid-liquid extraction with different solvents, adsorption over activated carbons and polymeric and inorganic adsorbents, membrane pervaporation and membrane-solvent extraction, have been discussed. Destruction technologies such as non-catalytic, supercritical and catalytic wet air oxidation, ozonation, non-catalytic, catalytic and enzymatic peroxide wet oxidation, electrochemical and photocatalytic oxidation, supercritical wet gasification, destruction with electron discharges as well as biochemical treatments have been considered. As for the abatement of phenol from gases, condensation, absorption in liquids, adsorption on solids, membrane separation, thermal, catalytic, photocatalytic and biological oxidation have also been considered. The experimental conditions and the performances of the different techniques have been compared.

  19. Technologies for the removal of phenol from fluid streams: A short review of recent developments

    Energy Technology Data Exchange (ETDEWEB)

    Busca, Guido [Consorzio Interdipartimentale di Monitoraggio Ambientale, Facolta di Ingegneria, Universita di Genova, via Cadorna 7, I-17100 Savona (Italy); Dipartimento di Ingegneria Chimica e di Processo, Facolta di Ingegneria, Universita di Genova, Pl.e Kennedy 1, I-16129 Genova (Italy)], E-mail: Guido.Busca@unige.it; Berardinelli, Silvia; Resini, Carlo [Consorzio Interdipartimentale di Monitoraggio Ambientale, Facolta di Ingegneria, Universita di Genova, via Cadorna 7, I-17100 Savona (Italy); Dipartimento di Ingegneria Chimica e di Processo, Facolta di Ingegneria, Universita di Genova, Pl.e Kennedy 1, I-16129 Genova (Italy); Arrighi, Laura [Dipartimento di Ingegneria Chimica e di Processo, Facolta di Ingegneria, Universita di Genova, Pl.e Kennedy 1, I-16129 Genova (Italy)

    2008-12-30

    The available technologies for the abatement of phenol from water and gaseous streams are briefly reviewed, and the recent advancements summarized. Separation technologies such as distillation, liquid-liquid extraction with different solvents, adsorption over activated carbons and polymeric and inorganic adsorbents, membrane pervaporation and membrane-solvent extraction, have been discussed. Destruction technologies such as non-catalytic, supercritical and catalytic wet air oxidation, ozonation, non-catalytic, catalytic and enzymatic peroxide wet oxidation, electrochemical and photocatalytic oxidation, supercritical wet gasification, destruction with electron discharges as well as biochemical treatments have been considered. As for the abatement of phenol from gases, condensation, absorption in liquids, adsorption on solids, membrane separation, thermal, catalytic, photocatalytic and biological oxidation have also been considered. The experimental conditions and the performances of the different techniques have been compared.

  20. Application of gas-fluid atomization technology in ultrosonic vibration cutting titanium alloy workpiece

    Science.gov (United States)

    Zhou, Zhimin; Zhang, Yuangliang; Li, Xiaoyan; Sun, Baoyuan

    2009-11-01

    To further improve machined surface quality of diamond cutting titanium workpiece and reduce diamond tool wear, it puts forward a kind of machining technology with mixture of carbon dioxide gas, water and vegetable oil atomized mist as cooling media in the paper. The cooling media is sprayed to cutting area through gas-liquid atomizer device to achieve purpose of cooling, lubricating, and protecting diamond tool. Experiments indicate that carbon dioxide gas can touch cutting surface more adequately through using gas-liquid atomization technology, which makes iron atoms of cutting surface cause a chemical reaction directly with carbon in carbon dioxide gas and reduce graphitizing degree of diamond tool. Thus, this technology of using gas-liquid atomization and ultrasonic vibration together for cutting Titanium Alloy is able to improve machined surface quality of workpiece and slow of diamond tool wear.

  1. Sealed source dismantling hot cell - startup

    Energy Technology Data Exchange (ETDEWEB)

    Dellamano, Jose Claudio; Ferreira, Robson de Jesus, E-mail: jcdellam@ipen.br, E-mail: rojefer@ipen.br [Instituto de Pesquisas Energeticas e Nucleares (IPEN/CNEN-SP), Sao Paulo, SP (Brazil). Gerencia de Rejeitos radioativos

    2013-07-01

    Sealed radioactive sources are widely used in many applications of nuclear technology and at the end of the useful life, most sources become radioactive waste. In Brazil, this waste is received by the Institutes of the National Nuclear Energy Commission and kept under centralized storage. The Waste Management Department at the Nuclear and Energy Research Institute is the main storage center, having received around 20,000 disused sources. A hot cell was designed and constructed to manage Co-60 spent sealed sources with activity up to 3.7 10{sup 1}0 Bq and other sources with equivalent activities. In the hot cell the sources are withdraw from their original shielding and transferred to a standard shielding for further disposal off. The original shielding disassembling is made outside the hot cell and after opening, it is transferred inside the hot cell and the sealed source is removed remotely. The source is checked in relation to external contamination and its activity is checked. After this, the source is positioned in the standard shielding located inside an overpack at the bottom of the hot cell. This paper describes some pre-operational tests carried out in it, that include: opening and closing doors and locks, checking of all electrical and pneumatic controls, the original shielding movement inside the hot-cell, dose rate measurements outside the hot-cell, insertion of the sealed sources inside the activity meter chamber, transferring the sealed source to the standard shielding, movement of the overpack with the standard shielding to outside of the hot-cell and plugging of the standard shielding. (author)

  2. Leakage predictions for Rayleigh-step, helium-purge seals

    Science.gov (United States)

    Proctor, Margaret P.

    1988-01-01

    Rayleigh-step, helium purge, annular shaft seals, studied for use in liquid oxygen turbopumps, generate a hydrodynamic force that enables the seal to follow shaft perturbations. Hence, smaller clearances can be used to reduce seal leakage. FLOWCAL, a computer code developed by Mechanical Technology Incorporated, predicts gas flow rate through an annular seal with an axial pressure gradient. Analysis of a 50-mm Rayleigh-step, helium-purge, annular seal showed the flow rate increased axial pressure gradient, downstream pressure, and eccentricity ratio. Increased inlet temperature reduced leakage. Predictions made at maximum and minimum clearances (due to centrifugal and thermal growths, machining tolerances and + or - 2 percent uncertainty in the clearance measurement) placed wide boundaries on expected flow rates. The widest boundaries were set by thermal growth conditions. Predicted flow rates for a 50-mm Rayleigh-step, helium-purge, annular seal underestimated measured flow rates by three to seven times. However, the analysis did accurately predict flow rates for choked gas flow through annular seals when compared to flow rates measured in two other independent studies.

  3. Sealing the mitochondrial respirasome.

    Science.gov (United States)

    Winge, Dennis R

    2012-07-01

    The mitochondrial respiratory chain is organized within an array of supercomplexes that function to minimize the generation of reactive oxygen species (ROS) during electron transfer reactions. Structural models of supercomplexes are now known. Another recent advance is the discovery of non-OXPHOS complex proteins that appear to adhere to and seal the individual respiratory complexes to form stable assemblages that prevent electron leakage. This review highlights recent advances in our understanding of the structures of supercomplexes and the factors that mediate their stability.

  4. Detection of Neisseria meningitidis in cerebrospinal fluid using a multiplex PCR and the Luminex detection technology

    DEFF Research Database (Denmark)

    Møller, Jens Kjølseth

    2012-01-01

    Rapid clinical and laboratory diagnoses are the foundation for a successful management of serious infections with Neisseria meningitidis. A species-specific multiplex polymerase chain reaction (PCR) coupled with fluidic microarrays using microbeads (the Luminex xMAP™ Technology) can detect pathog...

  5. Fluid mechanics for mechanical engineering. Technology and examples; Stroemungslehre fuer den Maschinenbau. Technik und Beispiele

    Energy Technology Data Exchange (ETDEWEB)

    Siekmann, H.E. [Technische Univ. Berlin (Germany). Hermann-Foettinger-Institut fuer Stroemungsmechanik

    2001-07-01

    The book complements the established fluid mechanics textbook. It discusses the same subjects but goes into more detail and contains many practical examples. It addresses students of engineering, physics and practically oriented mathematics and can be used for independent studying or for a deeper understanding of subject matter treated in university lectures. [German] Der Band stellt als Ergaenzung zum eingefuehrten Grundlagenbuch Stroemungslehre eine tiefergehende Behandlung des Vorlesungsstoffes dar. Die Einteilung der Kapitel entspricht im wesentlichen der im Band Grundlagen: Hydrostatik, Kinematik, Impulssatz, NAVIER-Stokes-Bewegungsgleichung, Potential-, Wirbel- und Grenzschichtstroemung sowie turbulente Stroemung. Das Buch schliesst mit Darstellungen ueber Rohrstroemungen, Umstroemungen von Koerpern, Aehnlichkeitsgesetzen und numerische Stroemungsberechnung. Es enthaelt zahlreiche Praxisbeispiele. Geeignet fuer Studenten der Ingenieurwissenschaften, Physiker und praxisorientierte Mathematiker zum Selbststudium sowie zur Vorlesungsbegleitung. (orig.)

  6. A nanosystem for water-insoluble drugs prepared by a new technology, nanoparticulation using a solid lipid and supercritical fluid.

    Science.gov (United States)

    Park, Joo Won; Yun, Jeong Min; Lee, Eun Seong; Youn, Yu Seok; Kim, Kab Sig; Oh, Young Taik; Oh, Kyung Teak

    2013-11-01

    While the number and diversity of lead compounds has increased with the development of science technologies, ca. 90 % of new chemical entities under development have shown low aqueous solubility, classified as class II or IV of the biopharmaceutics classification system (BCS). The low aqueous solubility hinders their clinical translations due to low bioavailability and dissolution-limited absorption of orally-administered drugs. Several technologies have been employed to improve the solubility of poorly water-soluble drugs. In this paper, a new method of nanoparticulation using fat and a supercritical fluid (NUFS) for the formulation of hydrophobic drugs was applied to solve the low solubility problem. A typical BCS class II drug, itraconazole, was selected and formulated with hydroxypropyl methylcellulose, emulsification, and anticoagulating agents for NUFS. The non-spherical itraconazole nanoparticles prepared by NUFS were ~300-500 nm in size with a ~15-fold improved dissolution rate compared to non-nanoparticles of itraconazole (i.e., raw itraconazole). In addition, a high drug content of ~46 % by weight and a drug loading efficiency greater than 85 % were achieved. Therefore, the new technology for nano-platforms could be a promising solution for solubilization of poorly water-soluble drugs, resulting in improved bioavailability.

  7. Can symmetry transitions of complex fields enable 3-d control of fluid vorticity?

    Energy Technology Data Exchange (ETDEWEB)

    Martin, James E. [Sandia National Laboratories (SNL-NM), Albuquerque, NM (United States); Solis, Kyle Jameson [Sandia National Laboratories (SNL-NM), Albuquerque, NM (United States)

    2015-08-01

    Methods of inducing vigorous noncontact fluid flow are important to technologies involving heat and mass transfer and fluid mixing, since they eliminate the need for moving parts, pipes and seals, all of which compromise system reliability. Unfortunately, traditional noncontact flow methods are few, and have limitations of their own. We have discovered two classes of fields that can induce fluid vorticity without requiring either gravity or a thermal gradient. The first class we call Symmetry-Breaking Rational Fields. These are triaxial fields comprised of three orthogonal components, two ac and one dc. The second class is Rational Triad Fields, which differ in that all three components are alternating. In this report we quantify the induced vorticity for a wide variety of fields and consider symmetry transitions between these field types. These transitions give rise to orbiting vorticity vectors, a technology for non-contact, non-stationary fluid mixing.

  8. A supercritical fluid-based coating technology. 3: preparation and characterization of bovine serum albumin particles coated with lipids.

    Science.gov (United States)

    Ribeiro Dos Santos, I; Richard, J; Thies, C; Pech, B; Benoit, J-P

    2003-01-01

    Solvent-free microparticles, loaded with bovine serum albumin as a model protein, were produced using a novel supercritical (SC) fluid-based coating technology. Coating material consists either of trimyristin (Dynasan 114) or of Gelucire 50-02. Microparticles obtained were characterized as regards their morphology, protein content and in vitro release profile. A discontinuous coating made of micro-needles of trimyristin led to an initial burst release of approximately 70% in 30 min. However, a prolonged release of the BSA could be achieved in a phosphate buffer solution at 37 degrees C over a 24 h period from particles coated with Gelucire 50-02. Furthermore, it was shown that BSA does not undergo any degradation after SC CO(2) treatment under the conditions used in the coating process.

  9. Force-controlled spatial manipulation of viable mammalian cells and micro-organisms by means of FluidFM technology

    Science.gov (United States)

    Dörig, Pablo; Stiefel, Philipp; Behr, Pascal; Sarajlic, Edin; Bijl, Daniel; Gabi, Michael; Vörös, János; Vorholt, Julia A.; Zambelli, Tomaso

    2010-07-01

    The FluidFM technology uses microchanneled atomic force microscope cantilevers that are fixed to a drilled atomic force microscope cantilevers probeholder. A continuous fluidic circuit is thereby achieved extending from an external liquid reservoir, through the probeholder and the hollow cantilever to the tip aperture. In this way, both overpressure and an underpressure can be applied to the liquid reservoir and hence to the built-in fluidic circuit. We describe in this letter how standard atomic force microscopy in combination with regulated pressure differences inside the microchanneled cantilevers can be used to displace living organisms with micrometric precision in a nondestructive way. The protocol is applicable to both eukaryotic and prokaryotic cells (e.g., mammalian cells, yeasts, and bacteria) in physiological buffer. By means of this procedure, cells can also be transferred from one glass slide to another one or onto an agar medium.

  10. Bubble column reactor fluid dynamic study at pilot plant scale for residue and extra heavy crude oil upgrading technology

    Energy Technology Data Exchange (ETDEWEB)

    Sardella, R.; Medina, H. [Infrastructure and Upgrading Department PDVSA-Intevep (Venezuela); Zacarias, L.; Paiva, M. [Refining Department. PDVSA-Intevep (Venezuela)

    2011-07-01

    Bubble column reactors are used in several applications because of their simplicity and low cost; a new technology was developed to convert extra heavy crude oil into upgraded crude using a bubble column reactor. To design this kind of reactor, a lot of parameters like flow regime, gas hold up and dispersion coefficient have to be taken into account. This study aimed at determining the fluid dynamic behaviour of a bubble column working under Aquaconversion operating conditions. Experiments were undertaken on air-tap water and air-light oil systems under atmospheric conditions with various gas superficial velocities and liquid flowrates. Results showed that gas hold up increases with superficial gas velocity but is independent of liquid flowrate and that both systems tested work at the same flow regimes. This paper showed that under the experimental conditions used, this reactor tends to be a complete mixing reactor.

  11. A New Seal Technology-Ceramics Seal%一种新型的密封技术一陶瓷密封

    Institute of Scientific and Technical Information of China (English)

    童幸生

    2001-01-01

    针对密封装置中存在的问题,概述了密封技术的种类和方法,从选用工程陶瓷材料制作密封元件出发,论述了陶瓷材料的密封特性,并举出了工业上使用密封结构的实例,说明利用工程陶瓷制作密封元件是可行的。%According to the problems exsisted in sealing devices, this paper introduces the types and methods of seal technology. And starting from selecting engineering ceramicc materials as sealing elements, it describes the sealing characteristics of the ceramic material, and takes examples of sealing stucture used in industry and shows that using engineering ceramic materials as seals is feasible.

  12. Review of results from SKB R and D on grouting technology for sealing the rock, years 1996-2000; Oeversikt av resuItat fraan SKB:s FoU inom injekteringsteknik foer bergtaetning aaren 1996-2000

    Energy Technology Data Exchange (ETDEWEB)

    Boden, A. (ed.) [Swedpower AB, Stockholm (Sweden); Eklund, D. [Vattenfall Utveckling AB, Aelvkarleby (Sweden); Eriksson, Magnus [Royal Inst. of Technology, Stockholm (Sweden). Div. Soil and Rock Mechanics; Fransson, Aasa [Chalmers Univ. of Technology, Goeteborg (Sweden). Inst. of Geology; Hansson, Paer [Vattenfall Utveckling AB, Aelvkarleby (Sweden); Lagerblad, B. [Swedish Cement and Concrete Research Inst., Stockholm (Sweden); Lindblom, U. [Chalmers Univ. of Technology, Goeteborg (Sweden). Dept. of Geotechnical Engineering; Wilen, P. [Swedpower AB, Goeteborg (Sweden)

    2001-05-01

    In order identify the current state of the art and developments needs, SKB assembled a group of experts from universities and other research organisations. Internal plans were written for the subprojects 'Characterisation of rock for grouting purposes', 'Mechanisms that control the spreading of grout in jointed rock' and 'Cement based grouting material'. Later internal plans for the subprojects 'Demands on grouting' and 'Stabilising and sealing effect of pre-grouting' were written. The aims, which were set for the different subprojects, were in short, to summarise the technological advances, establish a method for rock characterisation from a grouting point of view, develop conceptual and numerical models for simulation of the grouting course, characterise grout in a relevant way, develop understanding and theoretical know-how of durability and chemical influence, identify and develop a number of grouting materials for different situations, develop a specification of requirements for grouting and to verify the theories in laboratory. In the subproject 'Demands on grouting' a literature review was carried out. One important conclusion from the study is that the concept is not very well dealt with in the literature. SKB are currently investigating the prerequisites for the construction of the deep repository. One part of that work is to further specify demands on maximum allowed volume of leakage water for the repository as a whole and also for each part of the deep repository. In the subproject 'Characterisation of rock for grouting purposes', the possibilities of using hydraulic tests for predictions and design have been studied. The idea of this study was to investigate correspondences and deviations to increase the understanding of what is measured in a water-loss measurement. One can draw the conclusion that hydraulic tests are useful when describing the fracture geometry. Numerical modelling

  13. Simultaneous Detection of Five Pathogens from Cerebrospinal Fluid Specimens Using Luminex Technology

    Directory of Open Access Journals (Sweden)

    Linfu Zhou

    2016-02-01

    Full Text Available Early diagnosis and treatment are crucial for the outcome of central nervous system (CNS infections. In this study, we developed a multiplex PCR-Luminex assay for the simultaneous detection of five major pathogens, including Mycobacterium tuberculosis, Cryptococcus neoformans, Streptococcus pneumoniae, and herpes simplex virus types 1 and 2, which frequently cause CNS infections. Through the hybridization reaction between multiplex PCR-amplified targets and oligonucleotide “anti-TAG” sequences, we found that the PCR-Luminex assay could detect as low as 101–102 copies of synthetic pathogen DNAs. Furthermore, 163 cerebrospinal fluid (CSF specimens from patients with suspected CNS infections were used to evaluate the efficiency of this multiplex PCR-Luminex method. Compared with Ziehl-Neelsen stain, this assay showed a high diagnostic accuracy for tuberculosis meningitis (sensitivity, 90.7% and specificity, 99.1%. For cryptococcal meningitis, the sensitivity and specificity were 92% and 97.1%, respectively, compared with the May Grunwald Giemsa (MGG stain. For herpes simplex virus types 1 and 2 encephalitis, the sensitivities were 80.8% and 100%, and the specificities were 94.2% and 99%, respectively, compared with Enzyme Linked Immunosorbent Assay (ELISA assays. Taken together, this multiplex PCR-Luminex assay showed potential efficiency for the simultaneous detection of five pathogens and may be a promising supplement to conventional methods for diagnosing CNS infections.

  14. Development of accelerated dewatering technology for managing oil sands fine fluid tailings

    Energy Technology Data Exchange (ETDEWEB)

    Lahaie, R. [Syncrude Canada Ltd., Fort McMurray, AB (Canada); Seto, J.T.C. [BGC Engineering Inc., Edmonton, AB (Canada); Chapman, D. [O' Kane Consultants Inc., Saskatoon, SK (Canada); Carrier, W.D. III [Argila Enterprises Inc., Lakeland, FL (United States)

    2010-07-01

    This article discussed an accelerated dewatering technique being applied and tested for managing fine fluid tailings produced from oil sands mining. The process involved rim ditching and a decant system to promote the drainage of surface waters and enhance the drying and densification of mature fine tailings (MFT). To field test the procedure, a deposit containing 60,000 cubic metres of in-line flocculated MFT was constructed and instrumented to monitor consolidation and dewatering response of the MFT deposit over time. Ten months after being filled, the deposit had settled about 1.2 metres, which corresponds to a 19 percent reduction in volume relative to initial filling. The field test will continue for several more years, during which time the deposit will continue to be monitored and sampled. The Florida phosphate industry has used rim ditching for over 20 years, but the process had never before been applied to oil sand tailings. The paper discussed the particular consolidation behaviour of MFT, the rim ditch concept, the layout of the containment pit and instrumentation, the pit filling procedure, and post-filling observations. 6 refs., 12 figs.

  15. Gulf and Dilmun Type seals

    DEFF Research Database (Denmark)

    Laursen, Steffen

    2011-01-01

    these Gulf Type‘ seals drew heavily on Indus Valley iconography and Indus script was occasionally employed in a pidgin-like manner. While the earliest circular seals incorporate features from Mesopotamian glyptic only to a lesser extent, this becomes a more important source of inspiration for later Dilmun...

  16. Face-Sealing Butterfly Valve

    Science.gov (United States)

    Tervo, John N.

    1992-01-01

    Valve plate made to translate as well as rotate. Valve opened and closed by turning shaft and lever. Interactions among lever, spring, valve plate, and face seal cause plate to undergo combination of translation and rotation so valve plate clears seal during parts of opening and closing motions.

  17. Seals. Grades 3-6.

    Science.gov (United States)

    New England Aquarium, Boston, MA.

    Explanations of a marine mammal rescue program and information on seals and sea lions are presented in this curriculum package for intermediate grade teachers. Activities are highlighted which focus on the natural history of harbor seals. This unit contains: (1) pre-trip activities (including fact sheets and worksheets on the different types of…

  18. High temperature autoclave vacuum seals

    Science.gov (United States)

    Hoffman, J. R.; Simpson, W. G.; Walker, H. M.

    1971-01-01

    Aluminum sheet forms effective sealing film at temperatures up to 728 K. Soft aluminum wire rings provide positive seal between foil and platen. For applications at temperatures above aluminum's service temperature, stainless steel is used as film material and copper wire as sealant.

  19. Labyrinth Seal Flutter Analysis and Test Validation in Support of Robust Rocket Engine Design

    Science.gov (United States)

    El-Aini, Yehia; Park, John; Frady, Greg; Nesman, Tom

    2010-01-01

    High energy-density turbomachines, like the SSME turbopumps, utilize labyrinth seals, also referred to as knife-edge seals, to control leakage flow. The pressure drop for such seals is order of magnitude higher than comparable jet engine seals. This is aggravated by the requirement of tight clearances resulting in possible unfavorable fluid-structure interaction of the seal system (seal flutter). To demonstrate these characteristics, a benchmark case of a High Pressure Oxygen Turbopump (HPOTP) outlet Labyrinth seal was studied in detail. First, an analytical assessment of the seal stability was conducted using a Pratt & Whitney legacy seal flutter code. Sensitivity parameters including pressure drop, rotor-to-stator running clearances and cavity volumes were examined and modeling strategies established. Second, a concurrent experimental investigation was undertaken to validate the stability of the seal at the equivalent operating conditions of the pump. Actual pump hardware was used to construct the test rig, also referred to as the (Flutter Rig). The flutter rig did not include rotational effects or temperature. However, the use of Hydrogen gas at high inlet pressure provided good representation of the critical parameters affecting flutter especially the speed of sound. The flutter code predictions showed consistent trends in good agreement with the experimental data. The rig test program produced a stability threshold empirical parameter that separated operation with and without flutter. This empirical parameter was used to establish the seal build clearances to avoid flutter while providing the required cooling flow metering. The calibrated flutter code along with the empirical flutter parameter was used to redesign the baseline seal resulting in a flutter-free robust configuration. Provisions for incorporation of mechanical damping devices were introduced in the redesigned seal to ensure added robustness

  20. Green biodiesel production: a review on feedstock, catalyst, monolithic reactor, and supercritical fluid technology

    Directory of Open Access Journals (Sweden)

    Rizo Edwin Gumba

    2016-09-01

    Full Text Available The advancement of alternative energy is primarily catalyzed by the negative environmental impacts and energy depletion caused by the excessive usage of fossil fuels. Biodiesel has emerged as a promising substitute to petrodiesel because it is biodegradable, less toxic, and reduces greenhouse gas emission. Apart from that, biodiesel can be used as blending component or direct replacements for diesel fuel in automotive engines. A diverse range of methods have been reported for the conversion of renewable feedstocks (vegetable oil or animal fat into biodiesel with transesterification being the most preferred method. Nevertheless, the cost of producing biodiesel is higher compared to fossil fuel, thus impeding its commercialization potentials. The limited source of reliable feedstock and the underdeveloped biodiesel production route have prevented the full-scale commercialization of biodiesel in many parts of the world. In a recent development, a new technology that incorporates monoliths as support matrices for enzyme immobilization in supercritical carbon dioxide (SC-CO2 for continuous biodiesel production has been proposed to solve the problem. The potential of SC-CO2 system to be applied in enzymatic reactors is not well documented and hence the purpose of this review is to highlight the previous studies conducted as well as the future direction of this technology.

  1. Fluid dipping technology of chimpanzees in Comoé National Park, Ivory Coast.

    Science.gov (United States)

    Lapuente, Juan; Hicks, Thurston C; Linsenmair, K Eduard

    2017-05-01

    Over a 6 month period during the dry season, from the end of October 2014 to the beginning of May 2015, we studied tool use behavior of previously unstudied and non-habituated savanna chimpanzees (Pan troglodytes verus) living in the Comoé National Park, Ivory Coast (CI). We analyzed all the stick tools and leaf-sponges found that the chimpanzees used to forage for ants, termites, honey, and water. We found a particular behavior to be widespread across different chimpanzee communities in the park, namely, dipping for water from tree holes using sticks with especially long brush-tip modifications, using camera traps, we recorded adults, juveniles, and infants of three communities displaying this behavior. We compared water dipping and honey dipping tools used by Comoé chimpanzees and found significant differences in the total length, diameter, and brush length of the different types of fluid-dipping tools used. We found that water dipping tools had consistently longer and thicker brush-tips than honey dipping tools. Although this behavior was observed only during the late dry season, the chimpanzees always had alternative water sources available, like pools and rivers, in which they drank without the use of a tool. It remains unclear whether the use of a tool increases efficient access to water. This is the first time that water dipping behavior with sticks has been found as a widespread and well-established behavior across different age and sex classes and communities, suggesting the possibility of cultural transmission. It is crucial that we conserve this population of chimpanzees, not only because they may represent the second largest population in the country, but also because of their unique behavioral repertoire. © 2016 Wiley Periodicals, Inc.

  2. Turbine and Structural Seals Team Facilities

    Data.gov (United States)

    Federal Laboratory Consortium — Seals Team Facilities conceive, develop, and test advanced turbine seal concepts to increase efficiency and durability of turbine engines. Current projects include...

  3. Turbine and Structural Seals Team Facilities

    Data.gov (United States)

    Federal Laboratory Consortium — Seals Team Facilities conceive, develop, and test advanced turbine seal concepts to increase efficiency and durability of turbine engines. Current projects include...

  4. 大面积采空区密闭施工工艺探讨%Discussion on the sealing construction technology of large area goaf

    Institute of Scientific and Technical Information of China (English)

    赵亮

    2015-01-01

    With the constantly mine development, occur the state that the gobs the different mining areas connect each other, the connection between the gobs, the nonunfiorm pressure distribution of peripheral roadway will lead to air leakage between gobs, bring great difficulties to fire prevention and control work, so it is necessary to strengthen the air leakage control in closed session, the good or bad of the closed construction technology and quality is the key to the success or failure of fire prevention and extinguishing.%随着矿井的不断开拓,各采区存在大面积采空区相连的现状,采空区之间的相互连接以及外围巷道压差分布不均,将导致采空区之间漏风,给防灭火工作带来巨大困难,因此需要在密闭环节加强漏风控制,密闭施工工艺及质量的好坏对做好防灭火工作至关重要.

  5. Preparation of (Ti, Sn)O2 Nano-Composite Photocatalyst by Supercritical Fluid Dry Combination Technology

    Institute of Scientific and Technical Information of China (English)

    Jingchang ZHANG; Qing LI; Weiliang CAO

    2005-01-01

    A series of TiO2-SnO2 nano-sized composite photo-catalysts containing Sn (9.3%~30.1%) were prepared from TiCl4and SnCl4.5H2O by using sol-gel, supercritical fluid dry and solid-phase reaction (SCFD) combination technology.Characterizations with X-ray diffraction (XRD), transmission electron microscopy (TEM) and Fourier Transform Infrared Spectroscopy (FTIR) showed that, in addition to anatase type TiO2, a new active phase (Ti, Sn)O2 (with particle size of 2.0~4.3 nm) formed, and there were no SnO2 crystals observed in the range of the doping concentration studied. Photo-catalytic reaction of phenol was used as a model reaction to evaluate the catalytic activities of the obtained catalysts. Compared with pure TiO2 or Ti-Sn catalyst prepared with general sol-gel method, Ti-Sn nanocomposite photo-catalyst thus obtained showed significant improvement in catalytic activity. The photo-catalytic degradation rate of phenol could reach as high as 93.5% after 7 h. The preparation conditions of the new phase (Ti, Sn)O2 were investigated and its catalytic mechanism was proposed. The photo-catalytic particles prepared using SCFD combination technology exhibited small particle size, large surface area and high activity.

  6. Supercritical fluids as a green technology for the pretreatment of lignocellulosic biomass.

    Science.gov (United States)

    Daza Serna, L V; Orrego Alzate, C E; Cardona Alzate, C A

    2016-01-01

    One of the main drawbacks for using lignocellulosic biomass is related to its recalcitrance. The pretreatment of lignocellulosic biomass plays an important role for delignification and crystallinity reduction purposes. In this work rice husk (RH) was submitted to supercritical pretreatment at 80°C and 270 bar with the aim to determine the effect on lignin content, crystallinity as well as enzymatic digestibility. The yields obtained were compared with dilute sulfuric acid pretreatment as base case. Additionally a techno-economic and environmental comparison of the both pretreatment technologies was performed. The results show a lignin content reduction up to 90.6% for the sample with 75% moisture content using a water-ethanol mixture. The results for crystallinity and enzymatic digestibility demonstrated that no reductions were reached. Supercritical pretreatment presents the best economical and environmental performance considering the solvents and carbon dioxide recycling.

  7. Micronization processes by supercritical fluid technologies: a short review on process design (2008-2012 - doi: 10.4025/actascitechnol.v35i4.18819

    Directory of Open Access Journals (Sweden)

    Jose Vladimir de Oliveira

    2013-10-01

    Full Text Available Several micronization processes based on supercritical fluids have been developed. These processes can be classified according to the role of the supercritical fluid in the process: solvent, solute or co-solvent, and anti-solvent. Application of supercritical fluids as alternative to traditional micronization methods and the growing demand of the industrial sector for new technologies motivated this review. In this context, the objective of this work was to present the operating principles of the micronization process by means of supercritical fluids and the effects of the main process variables on particles characteristics. The review continues with an update of current experimental data presented in the literature in the period from 2008 to 2012.   

  8. Testing of molded high temperature plastic actuator road seals for use in advanced aircraft hydraulic systems

    Science.gov (United States)

    Waterman, A. W.; Huxford, R. L.; Nelson, W. G.

    1976-01-01

    Molded high temperature plastic first and second stage rod seal elements were evaluated in seal assemblies to determine performance characteristics. These characteristics were compared with the performance of machined seal elements. The 6.35 cm second stage Chevron seal assembly was tested using molded Chevrons fabricated from five molding materials. Impulse screening tests conducted over a range of 311 K to 478 K revealed thermal setting deficiencies in the aromatic polyimide molding materials. Seal elements fabricated from aromatic copolyester materials structurally failed during impulse cycle calibration. Endurance testing of 3.85 million cycles at 450 K using MIL-H-83283 fluid showed poorer seal performance with the unfilled aromatic polyimide material than had been attained with seals machined from Vespel SP-21 material. The 6.35 cm first stage step-cut compression loaded seal ring fabricated from copolyester injection molding material failed structurally during impulse cycle calibration. Molding of complex shape rod seals was shown to be a potentially controllable technique, but additional molding material property testing is recommended.

  9. Applications of supercritical fluid technology to pollution prevention and waste minimization

    Energy Technology Data Exchange (ETDEWEB)

    Turner, R.J. [Environmental Protection Agency, Cincinnati, OH (United States)

    1995-10-01

    One approach to the prevention of pollution and the reduction of worker exposure from conventional solvents is the use of less hazardous substitutes. One of the more novel substitutes is carbon dioxide. Although carbon dioxide is a gas at ordinary conditions, it can be liquified by application of pressure. In its supercritical state, it exhibits good solvent properties. Separation of the carbon dioxide from the extracted materials can be accomplished by pressure reduction, adsorption onto activated carbon, or with a membrane process, e.g., decaffeination of coffee. This paper presents a brief overview of the university and federal laboratory collaborative efforts focusing on processes using supercritical carbon dioxide as a substitute for hazardous solvents. The SCCO2 technology applications under this program include extraction of natural pharmaceutical materials, phase-transfer catalysis, solvent replacement in chemical synthesis, temperature-solubility relationships, and separation of organic materials from soils and slurries. A paper on the extraction of heavy metals with SCCO2 was presented by Ataai et.al. at the 87th National Meeting, A&WMA. This work is also supported by the EPA.

  10. Fluid technologies: The Bush Pump, the LifeStraw and microworlds of humanitarian design.

    Science.gov (United States)

    Redfield, Peter

    2016-04-01

    Over the past decade, many ingenious, small-scale gadgets have appeared in response to problems of disaster and extreme poverty. Focusing on the LifeStraw, a water filtration device invented by the company Vestergaard Frandsen, I situate this wave of humanitarian design relative to Marianne de Laet and Annemarie Mol's classic article on the Zimbabwe Bush Pump. The LifeStraw shares the Bush Pump's principle of technical minimalism, as well as its ethical desire to improve the lives of communities. Unlike the pump, however, the straw defines itself through rather than against market logic, accepting the premise that one can 'do well while doing good'. Moreover, it does not share the assumed framework of de Laet and Mol's Zimbabwean socio-technical landscape: a postcolonial state happily en route to national self-definition. Nonetheless, it clearly embodies moral affect, if in the idiom of humanitarian concern rather than development. My aim is to open up three interrelated lines of inquiry for discussion. First, I consider aspects of a postcolonial condition at the micro-level of immediate needs, including assumptions about nation-state politics and markets. Second, I emphasize science and technology in the form of infrastructure, the material frontline of norms. Third, I return reflexively to love, and the complicated allure of engagement in academic work.

  11. Establishment and application of drilling sealing model in the spherical grouting mode based on the loosing-circle theory

    Institute of Scientific and Technical Information of China (English)

    Hao; Zhiyong; Lin; Baiquan; Gao; Yabin; Cheng; Yanying

    2012-01-01

    There are quite a few studies that have been done on borehole sealing theory both domestically and internationally.The existing researches usually consider drilling of the surroundings as a dense homogeneous elastic body which does not meet the characteristics of real drilling of the fractured body.Based on the loosing-circle theory and analyses of the surrounding rock stress field,cracks and seepage fields,combined with Newtonian fluid spherical grouting model,we deduced the dynamic relationship between the seepage coefficient and rock or grouting parameters of the drilling sealing fluid mode of spherical fissure grouting.In this experiment,mucus was injected in the simulated coal seam and the permeability coefficient of the sealing body was calculated by using the model.To verify the validity of the model,the calculated sealing body number was compared with the extreme negative pressure that the sealing body could withstand.The theoretical model revealed the drilling sealing fluid mechanism,provided a method for the quantitative calculation of the drilling sealing fluid effect by grouting mode and a reference for the subsequent research of sealing mechanism.

  12. A nonintrusive nuclear monitor for measuring liquid contents in sealed vessels

    Science.gov (United States)

    Singh, J. J.; Mall, G. H.

    1984-01-01

    A nonintrusive nuclear technique for monitoring fluid contents in sealed vessels, regardless of the fluid distribution inside the vessels is described. The technique is applicable to all-g environments. It is based on the differences in Cesium-137 gamma ray attenuation coefficients in air and the test liquids.

  13. Algorithms of Optimum Slurry Selection for Soil and Rock Sealing Operations

    Directory of Open Access Journals (Sweden)

    Stryczek Stanis³aw

    2004-09-01

    Full Text Available Technical problems, usually caused by complex geological and hydrogeological conditions, are often encountered in mining, drilling and geoengineering operations, as well as in hydrotechnical and underground construction.Natural hazards in the above engineering operations are frequently liquidated by reinforcement and sealing of the ground with the use of injection methods with pre-selected sealing slurries.The authors present methods for slurry technological parameters normalization, depending on the scope and target of sealing operations, and algorithm of slurry selection of soil and rock sealing.

  14. [Effects of vacuum sealing drainage technique in acute and chronic suppurative tenosynovitis of hand].

    Science.gov (United States)

    Wang, H; Xia, F; Xing, D M; Ren, D; Feng, W; Chen, Y; Xiao, Z H; Zhao, Z M

    2017-05-01

    Objective: To investigate the effects of vacuum sealing drainage technique in acute and chronic suppurative tenosynovitis of hand. Methods: A total of 9 cases acute and chronic suppurative tenosynovitis patients from January 2013 to April 2015 in Puai Hospital Affiliated to Tongji Medical College, Huazhong University of Science and Technology were retrospectively reviewed. There were 6 males and 3 females, aging from 27 to 65 years, the average age was 55 years. There were 3 cases of index finger, 3 cases of middle finger, 2 cases of ring finger, 1 case include three fingers. The infection causes included stabbing with fishbone in 3 cases, stabbing with animal bone fragments in 3 cases, wound by sawdust in 3 cases, meat grinder injury in 1 case, multiple fingers crush injury postoperative infection of garbage truck in 1 case. Bacterial infection included 2 cases with Staphylococcus aureus, 2 cases with Staphylococcus epidermidis, 1 case with normal Escherichia coli, 1 case with mixed infection of Enterobacter aerogenes, Klebsiella oxytoca and Staphylococcus, 1 case with Bauman Acinetobacter bacillus, 1 case with Proteus mirabilis and 1 case of no growth of pathogenic bacteria culture. After thorough debridement, vacuum sealing drainage was used to observe the characteristics of irrigation fluid, the formation of cavity inflammation, the prognosis of infection and the recovery of finger function. Results: Seven patients with suppurative tenosynovitis were treated for 7 to 14 days, replaced the vacuum sealing drainage dressing once; 1 patient was an illustration of the finger tip defect flap infected patients after 21 days of treatment, replaced the vacuum sealing drainage dressing twice, 1 patient was an illustration of the central refers to trauma, postoperative infection patients 28 d, replaced three times in the VSD. The follow-up time was 3 to 12 months (mean 8.2 months), 7 patients without tendon necrosis, secondary suture with no infection, 2 cases of

  15. Ceramic-to-metal sealing. Final report

    Energy Technology Data Exchange (ETDEWEB)

    Gates, W.G.

    1977-03-01

    Ceramic-to-metal sealing was accomplished by brazing a metallized alumina insulator to a Kovar (Carpenter Technology Corporation) pin and header. A braze alloy wetting evaluation and a braze joint tensile strength evaluation were completed by brazing the specimens in a hydrogen atmosphere. From these evaluations the best braze alloy and brazing cycle were selected. Twelve braze alloys were evaluated and Nicusil 3 (Western Gold and Platinum Company) braze alloy was found to have good wetting characteristics and optimum strength. Assemblies brazed with this alloy were vacuum leak tight and metallurgically sound.

  16. 7 CFR 29.35 - Lot seal.

    Science.gov (United States)

    2010-01-01

    ... 7 Agriculture 2 2010-01-01 2010-01-01 false Lot seal. 29.35 Section 29.35 Agriculture Regulations of the Department of Agriculture AGRICULTURAL MARKETING SERVICE (Standards, Inspections, Marketing... INSPECTION Regulations Definitions § 29.35 Lot seal. A seal approved by the Director for sealing lots...

  17. 7 CFR 29.34 - Sample seal.

    Science.gov (United States)

    2010-01-01

    ... 7 Agriculture 2 2010-01-01 2010-01-01 false Sample seal. 29.34 Section 29.34 Agriculture Regulations of the Department of Agriculture AGRICULTURAL MARKETING SERVICE (Standards, Inspections, Marketing... INSPECTION Regulations Definitions § 29.34 Sample seal. A seal approved by the Director for sealing...

  18. Northern Fur Seal Food Habits

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — This data set contains food habits samples, usually scats, collected opportunistically on northern fur seal rookeries and haulouts in Alaska from 1987 to present....

  19. Alaska Harbor Seal Glacial Surveys

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — Floating glacial ice serves as a haul-out substrate for a significant number (10-15%) of Alaskan harbor seals, and thus surveying tidewater glacial fjords is an...

  20. Quantum String Seal Is Insecure

    CERN Document Server

    Chau, H F

    2006-01-01

    A quantum string seal encodes the value of a (bit) string as a quantum state in such a way that everyone can extract a non-negligible amount of information on the string by a suitable measurement. Moreover, such measurement must disturb the quantum state and is likely to be detected by an authorized verifier. In this way, the intactness of the encoded quantum state plays the role of a wax seal in the digital world. Here I analyze the security of quantum string seal by studying the information disturbance tradeoff of a measurement. This information disturbance tradeoff analysis extends the earlier results of Bechmann-Pasquinucci et al. and Chau by concluding that all quantum string seals are insecure. Specifically, I find a way to obtain non-trivial information on the string that escapes the verifier's detection with probability at least one half.

  1. Self Sealing Magmas

    Science.gov (United States)

    von Aulock, Felix W.; Wadsworth, Fabian B.; Kennedy, Ben M.; Lavallee, Yan

    2015-04-01

    During ascent of magma, pressure decreases and bubbles form. If the volume increases more rapidly than the relaxation timescale, the magma fragments catastrophically. If a permeable network forms, the magma degasses non-violently. This process is generally assumed to be unidirectional, however, recent studies have shown how shear and compaction can drive self sealing. Here, we additionally constrain skin formation during degassing and sintering. We heated natural samples of obsidian in a dry atmosphere and monitored foaming and impermeable skin formation. We suggest a model for skin formation that is controlled by diffusional loss of water and bubble collapse at free surfaces. We heated synthetic glass beads in a hydrous atmosphere to measure the timescale of viscous sintering. The beads sinter at drastically shorter timescales as water vapour rehydrates an otherwise degassed melt, reducing viscosity and glass transition temperatures. Both processes can produce dense inhomogeneities within the timescales of magma ascent and effectively disturb permeabilities and form barriers, particularly at the margins of the conduit, where strain localisation takes place. Localised ash in failure zones (i.e. Tuffisite) then becomes associated with water vapour fluxes and alow rapid rehydration and sintering. When measuring permeabilities in laboratory and field, and when discussing shallow degassing in volcanoes, local barriers for degassing should be taken into account. Highlighting the processes that lead to the formation of such dense skins and sintered infills of cavities can help understanding the bulk permeabilities of volcanic systems.

  2. Status of Understanding for Seal Materials

    Science.gov (United States)

    Brown, P. F.

    1984-01-01

    Material selection for mainshaft face and ring seals, labyrinth seals, accessory gearbox face seals, and lip seals are discussed in light of tribology requirements and a given seal application. Carbon graphite has been found to be one of the best sealing materials and it is widely used in current gas turbine mainshaft and accessory gearbox seals. Its popularity is due to its unique combination of properties which consists of dimensional stability, corrosion resistance, low friction, good self lubricating characteristics, high thermal conductivity and low thermal expansion, the latter two properties combining to provide good thermal shock resistance. A brief description of the seals and the requirements they must meet are discussed to provide insight into the limitations and advantages of the seals in containing the lubricant. A forecast is made of the operational requirements of main shaft and gearbox seals for advanced engines and candidate materials and coatings that may satisfy these advanced engine requirements.

  3. Brush Seals for Improved Steam Turbine Performance

    Science.gov (United States)

    Turnquist, Norman; Chupp, Ray; Baily, Fred; Burnett, Mark; Rivas, Flor; Bowsher, Aaron; Crudgington, Peter

    2006-01-01

    GE Energy has retrofitted brush seals into more than 19 operating steam turbines. Brush seals offer superior leakage control compared to labyrinth seals, owing to their compliant nature and ability to maintain very tight clearances to the rotating shaft. Seal designs have been established for steam turbines ranging in size from 12 MW to over 1200 MW, including fossil, nuclear, combined-cycle and industrial applications. Steam turbines present unique design challenges that must be addressed to ensure that the potential performance benefits of brush seals are realized. Brush seals can have important effects on the overall turbine system that must be taken into account to assure reliable operation. Subscale rig tests are instrumental to understanding seal behavior under simulated steam-turbine operating conditions, prior to installing brush seals in the field. This presentation discusses the technical challenges of designing brush seals for steam turbines; subscale testing; performance benefits of brush seals; overall system effects; and field applications.

  4. New dimension of slow food movement using supercritical fluid technology and methods to influence society by effective marketing strategies.

    Science.gov (United States)

    Uzel, Ruhan Aşkın

    2016-07-01

    Although slow food movement is a well-known movement nowadays, in order to make it more widespread to the society, necessity to develop and to adapt new techniques has become inevitable for healthier consumption age. For this purpose, possibility of increased usage of healthy foods with addition of natural extracts using new techniques came out from relevant questionaries applied to people of different age groups. In this study, specific properties of supercritical carbon dioxide at distinct temperatures and water in subcritical conditions were used to obtain extracts rich in water-soluble organic compounds. Experiments were carried out at pressures of 10, 20, 30, and 40 MPa and temperatures ranging from 40 to 200 ℃ with and without modifier for 2 h of extraction time. The flow rate was kept at 4 and 1 ml/min for CO2 and water, respectively. The highest water-soluble organic compound recovery yield was 78.10%. Results were supported by marketing strategies to announce this new application and products to the society. Group of sample questions was prepared to investigate (a) frequency of staple food usage, (b) the brand names and relevant reasons that bring up consumers to buy specifically same branded products, (c) knowledge about the ingredients and how advertising effects purchasing decision, etc. Finally, efficiency increase in slow food consumption was proved with supercritical fluid technology to draw attention to the health of consumers with newer and functional healthy foods. © The Author(s) 2015.

  5. 国内外页岩气钻井液技术应用现状%Application Actuality of Shale Gas Drilling Fluid Technology at Home and Abroad

    Institute of Scientific and Technical Information of China (English)

    齐从丽

    2014-01-01

    With the further exploration of oil and gas, shale gas development had gradually attracted the global attention. American was the earliest country of developing shale gas and had the most advanced technology. China had completed a certain number of shale gas wells since 2011 . The article mostly introduced shale gas drilling fluid technology at home and abroad and its application. Oil-based drilling fluid was mainly used for shale gas horizontal wells, and water-based drilling fluid was mainly used for vertical or directional wells. Oil-based drilling fluid tech-nology at home increasingly well formed and could meet the drilling requirements of the field, and de-oiled drilling cuttings could meet the requirements of environmental protection.%介绍了国内外页岩气钻井液技术及其应用情况,大部分页岩油气水平井采用油基钻井液,直井或定向井多采用水基钻井液;国内油基钻井液技术较为成熟,处理后的含油钻屑能达到环保要求。

  6. Experimental studies and performance analyses on polyurethane and nitrile rubber rod seals

    Science.gov (United States)

    Mirza, M.; Temiz, V.; Kamburoǧlu, E.

    2012-09-01

    The aim of this study is to determine the friction and leakage properties of rod seals made of polyethylene and nitrile rubber with different design geometries, under various pressure and lubricating oil viscosity conditions, in order to make assumptions about their general sealing characteristics and their pros and cons under certain working conditions that involve a range of fluid pressures. The test specimens consist of commercial rod seals of various designs and materials and were mounted on a hard chrome coated shaft subject to reciprocating motion. The test rig is capable of measuring friction force by means of strain measurements on a load cell transmitting the linear motion of a screw shaft to the test shaft. The test results of the reciprocating rod seal samples were evaluated according to leakage amount and friction resistance as a function of materials, design geometries and fluid pressures as well as the lubricating oil viscosity.

  7. 超临界流体技术制各类胡萝卜素纳米颗粒%Carotenoids particle formation by supercritical fluid technologies

    Institute of Scientific and Technical Information of China (English)

    全灿; Johan Carlfors; Charlotta Turner

    2009-01-01

    Based on the solubility in supercritical CO2, two strategies in which CO2 plays different roles are used to make quercetine and astaxanthin particles by supercritical fluid technologies. The experimental results showed that micronized quercetine particles with mean particle size of 1.0-1.5 um can be made via solution enhanced dis-persion by supercritical fluids (SEDS) process, in which CO2 worked as turbulent anti-solvent; while for astaxan-thin, micronized particles with mean particle size of 0.3-0.8 um were also made successfully by rapid expansion supercritical solution (RESS) process.

  8. Grease lubrication mechanisms in bearing seals

    OpenAIRE

    2011-01-01

    Rolling bearings contain seals to keep lubricant inside and contaminants outside the bearing system. These systems are often lubricated with grease; the grease acts as a lubricant for the bearing and seal and improves the sealing efficiency. In this thesis, the influence of lubricating grease on bearing seal performance is studied. Rheological properties of the grease, i.e. shear stress and normal stress difference, are evaluated and related to the lubricating and sealing performance of the s...

  9. An ideal sealed source life-cycle

    Energy Technology Data Exchange (ETDEWEB)

    Tompkins, Joseph Andrew [Los Alamos National Laboratory

    2009-01-01

    In the last 40 years, barriers to compliant and timely disposition of radioactive sealed sources have become apparent. The story starts with the explosive growth of nuclear gauging technologies in the 1960s. Dozens of companies in the US manufactured sources and many more created nuclear solutions to industrial gauging problems. Today they do not yet know how many Cat 1, 2, or 3 sources there are in the US. There are, at minimum, tens of thousands of sources, perhaps hundreds of thousands of sources. Affordable transportation solutions to consolidate all of these sources and disposition pathways for these sources do not exist. The root problem seems to be a lack of necessary regulatory framework that has allowed all of these problems to accumulate with no national plan for solving the problem. In the 1960s, Pu-238 displaced Pu-239 for most neutron and alpha source applications. In the 1970s, the availability of inexpensive Am-241 resulted in a proliferation of low energy gamma sources used in nuclear gauging, well logging, pacemakers, and X-ray fluorescence applications for example. In the 1980s, rapid expansion of worldwide petroleum exploration resulted in the expansion of Am-241 sources into international locations. Improvements of technology and regulation resulted in a change in isotopic distribution as Am-241 made Pu-239 and Pu-238 obsolete. Many early nuclear gauge technologies have been made obsolete as they were replaced by non-nuclear technoogies. With uncertainties in source end of life disposition and increased requirements for sealed source security, nuclear gauging technology is the last choice for modern process engineering gauging solutions. Over the same period, much was learned about licensing LLW disposition facilities as evident by the closure of early disposition facilities like Maxey Flats. The current difficulties in sealed source disposition start with adoption of the NLLW policy act of 1985, which created the state LLW compact system they

  10. Carbon Dioxide Sealing Capacity: Textural or Compositional Controls?

    Energy Technology Data Exchange (ETDEWEB)

    Cranganu, Constantin; Soleymani, Hamidreza; Sadiqua, Soleymani; Watson, Kieva

    2013-11-30

    This research project is aiming to assess the carbon dioxide sealing capacity of most common seal-rocks, such as shales and non-fractured limestones, by analyzing the role of textural and compositional parameters of those rocks. We hypothesize that sealing capacity is controlled by textural and/or compositional pa-rameters of caprocks. In this research, we seek to evaluate the importance of textural and compositional parameters affecting the sealing capacity of caprocks. The conceptu-al framework involves two testable end-member hypotheses concerning the sealing ca-pacity of carbon dioxide reservoir caprocks. Better understanding of the elements controlling sealing quality will advance our knowledge regarding the sealing capacity of shales and carbonates. Due to relatively low permeability, shale and non-fractured carbonate units are considered relatively imper-meable formations which can retard reservoir fluid flow by forming high capillary pres-sure. Similarly, these unites can constitute reliable seals for carbon dioxide capture and sequestration purposes. This project is a part of the comprehensive project with the final aim of studying the caprock sealing properties and the relationship between microscopic and macroscopic characteristics of seal rocks in depleted gas fields of Oklahoma Pan-handle. Through this study we examined various seal rock characteristics to infer about their respective effects on sealing capacity in special case of replacing reservoir fluid with super critical carbon dioxide (scCO{sub 2}). To assess the effect of textural and compositional properties on scCO{sub 2} maximum reten-tion column height we collected 30 representative core samples in caprock formations in three counties (Cimarron, Texas, Beaver) in Oklahoma Panhandle. Core samples were collected from various seal formations (e.g., Cherokee, Keys, Morrowan) at different depths. We studied the compositional and textural properties of the core samples using several techniques

  11. Study on seal improvement and rotor thrust control of centrifugal compressor

    Institute of Scientific and Technical Information of China (English)

    2007-01-01

    Fluid pressure variations due to process fluctuations or balance drum seal degradation can result in rotor thrust increasing that may jeopardize thrust bearing and compressor's reliability. Also, the leakage flow through balance drum seal can seriously affect the efficiency of compressor. A method that can improve both the efficiency and reliability of centrifugal compressor is presented. The method focused on rotor thrust control and balance drum seal upgrading. The low leakage feature of Dry-Gas-Seal(DGS), high reliability of labyrinth, and the feasibility of upgrading existing structure are taken into account at the same time to design a combined labyrinth-dry gas seal system on the balancing drum. Based on the combined seal system, a Fault Self-Recovering(FSR) system for the fault of rotor shaft displacement is introduced to assure the safety and reliability of centrifugal compressor. The modern Computational Fluid Dynamics(CFD) is used to validate this envision. The numerical result and relevant information indicate that the combined sealing system could improve the efficiency of the centrifugal compressor by about 4%.

  12. Development of Molten-Salt Heat Transfer Fluid Technology for Parabolic Trough Solar Power Plants - Public Final Technical Report

    Energy Technology Data Exchange (ETDEWEB)

    Grogan, Dylan C. P.

    2013-08-15

    Executive Summary This Final Report for the "Development of Molten-Salt Heat Transfer Fluid (HTF) Technology for Parabolic Trough Solar Power Plants” describes the overall project accomplishments, results and conclusions. Phase 1 analyzed the feasibility, cost and performance of a parabolic trough solar power plant with a molten salt heat transfer fluid (HTF); researched and/or developed feasible component options, detailed cost estimates and workable operating procedures; and developed hourly performance models. As a result, a molten salt plant with 6 hours of storage was shown to reduce Thermal Energy Storage (TES) cost by 43.2%, solar field cost by 14.8%, and levelized cost of energy (LCOE) by 9.8% - 14.5% relative to a similar state-of-the-art baseline plant. The LCOE savings range met the project’s Go/No Go criteria of 10% LCOE reduction. Another primary focus of Phase 1 and 2 was risk mitigation. The large risk areas associated with a molten salt parabolic trough plant were addressed in both Phases, such as; HTF freeze prevention and recovery, collector components and piping connections, and complex component interactions. Phase 2 analyzed in more detail the technical and economic feasibility of a 140 MWe,gross molten-salt CSP plant with 6 hours of TES. Phase 2 accomplishments included developing technical solutions to the above mentioned risk areas, such as freeze protection/recovery, corrosion effects of applicable molten salts, collector design improvements for molten salt, and developing plant operating strategies for maximized plant performance and freeze risk mitigation. Phase 2 accomplishments also included developing and thoroughly analyzing a molten salt, Parabolic Trough power plant performance model, in order to achieve the project cost and performance targets. The plant performance model and an extensive basic Engineering, Procurement, and Construction (EPC) quote were used to calculate a real levelized cost of energy (LCOE) of 11.50

  13. Subsurface Barrier Formation as a CO2 Leakage Mitigation Technology

    Science.gov (United States)

    Castaneda Herrera, C. A.; Stevens, G.; Haese, R. R.

    2015-12-01

    Long-term CO2 containment in a geological storage reservoir is a key criterion for successfully implementing carbon capture and storage (CCS), however, CO2 leakage through different pathways cannot be completely ruled out in some instances. In this study we investigate the conditions for reactive barrier formation as a technology to mitigate and remediate CO2 leakage. We propose to inject a liquid reagent consistent of an alkaline sodium-silicate solution on top of the storage caprock, which will lead to silica mineral precipitation when in contact with an acidic, CO2-enriched fluid. This reaction will create a barrier that seals the leakage by reducing the permeability. Preliminary modelling has shown that the density, viscosity and alkalinity of the reagent fluid are critical for a successful seal formation, whereas differences in formation water composition and in the rock mineral composition are less important. In order to study the reaction through experiments, different reagent solutions were prepared and characterised in terms of silica concentration, density, viscosity and buffer capacity. In a static, diffusion-controlled batch experiment we observed silica mineral precipitation in the outer layer of the piece of rock inhibiting further mixing of the two fluids and slowing down the initial reaction rate. Core-flood experiments will be carried out to simulate barrier formation under fluid flow conditions. Here, the sealing efficiency of the reaction will be continuously measured in terms of a change in permeability.

  14. Numerical Simulation of the Flow Field in Circumferential Grooved Liquid Seals

    Directory of Open Access Journals (Sweden)

    Meng Zhang

    2013-01-01

    Full Text Available Circumferential grooved liquid seals are utilized inside turbomachinery to provide noncontacting control of internal incompressible fluid leakage. Accurate prediction of the flow field is fundamental in producing robust and efficient designs. To validate the capabilities of the computational fluid dynamics FLUENT for incompressible fluid seal flow, comparisons of velocity parameters are made to the published experimental results and other CFD code for a circumferential grooved liquid seal. This work employs a pressure-based CFD code FLUENT to calculate the flow field in the seal, using four different turbulence models respectively. The velocity contours are compared with experimental values. It shows good overall agreement of the axial, radial, and azimuthal velocities in the through-flow jet, shear layer, and recirculation zone. Quantitative comparisons of velocity profiles at the center of the groove are made to experiment. This study verifies the prediction accuracy of three turbulence models. Various structures were considered to obtain a better understanding of the circumferential grooved liquid flow characteristics. The best groove structure to control leakage was also found within the limited designed seal. This study will provide a useful reference for designing the circumferential grooved liquid seal.

  15. Petrophysical Characterization of Arroyal Antiform Geological Formations (Aguilar de Campoo, Palencia) as a Storage and Seal Rocks in the Technology Development Plant for Geological CO{sub 2} Storage (Hontomin, Burgos); Caracterizacin Petrofisica de las Formaciones Geologicas de la Antiforma de Arroyal (Aguilar de Campoo, Palencia) como Posibles Rocas Almacen y Sello en la Planta de Desarrollo Tecnologico de Almacenamiento Geologico de CO{sub 2} (Hontomin, Burgos)

    Energy Technology Data Exchange (ETDEWEB)

    Campos, R.; Barrios, I.; Gonzalez, A. M.; Pelayo, M.; Saldana, R.

    2011-05-13

    The geological storage program of Energy City Foundation is focusing its research effort in the Technological Development and Research Plant in Hontomin (Burgos) start off. The present report shows the petrophysical characterization of of the Arroyal antiform geological formations since they are representatives, surface like, of the storage and seal formations that will be found in the CO{sub 2} injection plant in Hontomin. In this petrophysics characterization has taken place the study of matrix porosity, specific surface and density of the storage and seal formations. Mercury intrusion porosimetry, N{sub 2} adsorption and He pycnometry techniques have been used for the characterization. Furthermore, it has carried out a mineralogical analysis of the seal materials by RX diffraction. (Author) 26 refs.

  16. Harbour seals (Phoca vitulina and rehabilitation

    Directory of Open Access Journals (Sweden)

    Nynke Osinga

    2010-09-01

    Full Text Available Throughout the past few decades, rehabilitation of seals has become an activity that is anchored in the present day society of many countries. Seals are primarily rehabilitated to help individual animals in distress. At the same time, the release of seals which would have otherwise died can be considered as a contribution to the population. Most rehabilitated seals are animals under one year of age. They are mainly orphans, weaned seals with complications and seals with a parasiticbronchopneumonia. For the optimal handling of seals and their diseases, centralised operations with quality standards are essential. Rehabilitation provides an instrument to monitor the health of the seal population and its ecosystem. Changes in stranding trends or the appearance of new diseases can be monitored. Moreover, rehabilitation is important to show the general public thestate of the marine environment. In the Netherlands there is significant social support for the rehabilitation of seals. Experience obtained with seal care is of importance in countries where urgent help of threatened seal species is required. Here individual seals are also ambassadors to raise support for the protection of this species in general. Given that the anthropogenic impact on the seals and their environment is extensive in the Wadden Sea, rehabilitation centres can compensate the consequences of this impact on individual seals as well as the population as a whole.

  17. Sealing Performance of Labyrinth Seals against Small Oil Particles in HDDs

    Science.gov (United States)

    Miyatake, Masaaki; Yoshimoto, Shigeka; Dambara, Shinsuke; Nakamura, Taichi; Tanaka, Katsuhiko

    Small oil particles generated from lubricant for ball bearings in HDDs sometimes cause fatal problems such as head crashes. A labyrinth seal is often used to prevent oil particles from scattering onto the disk surfaces. In this paper, the sealing performance of labyrinth seals for small oil particles is investigated numerically and experimentally. Two types of labyrinth seal are considered, one a straight-type and the other a bent-type seal. It was found that the sealing capability of the labyrinth seal is generated by the centrifugal force exerted on oil particles due to disk rotation when they pass through the seal gap.

  18. Drilling Fluid Technology of CHE Oilfield in Argentina%阿根廷CHE油田钻井液技术

    Institute of Scientific and Technical Information of China (English)

    袁俊文

    2012-01-01

    Some difficulties are encountered in CHE oilfield, which are balled bit and stabilizer in upper formations, caving and sloughing in lower formations, thick mud cake in target formation, and contamination of HCO3~ in formations. The polymer drilling fluid system is successfully applied in 5 development wells, cooperated with advanced solid-control technology and anti-collapsing technology, the solids can be eliminated and also the weighting material can be saved to overcome the problems of solid-control of this oilfield.%CHE油田位于阿根廷门多萨市以南安第斯山脉东麓库亚那(Cuyana)盆地中部.该油田上部地层富含活性黏土,造浆趋势强,易出现钻头、扶正器泥包;下部地层受造山运动影响,地应力强,井壁稳定性差,掉块多,易发生卡钻;目的层渗透性好,易形成厚泥饼,导致起下钻阻卡严重;地层中含有CO2,易出现HCO3-污染;现场无钻屑池,要求钻屑不落地、废液零排放,对固相控制技术的要求高.江汉油田阿根廷项目部在该油田完成5口开发井,通过采用聚合物钻井液,配合先进的固相控制技术及针对性的防塌技术,较好地解决了以上技术难题.应用结果表明,将高、低速离心机串联使用,同时采用化学絮凝技术,既能清除劣质固相,又不浪费加重材料,能彻底解决该油田钻井液施工中的固相控制问题,有利于保持钻井液性能稳定.

  19. Fiscal 1996 investigational research on the chemical process technology using supercritical fluids; 1996 nendo chorinkai ryutai wo riyoshita kagaku process gijutsu ni kansuru chosa kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    Importance was studied of making a research on the chemical process technology using the supercritical fluid. As for its effect on global warming, the amount of CO2 emission was compared during the operation between the conventional process and the process using the supercritical fluid, the CO2 reduction rate and amount were trially calculated, and a CO2 reduction of a several ten thousand ton scale in carbon conversion was predicted. As to hazardous materials and the reaction of waste retrieval, it was made clear that the process using the supercritical fluid was valid also for objects for which the chemical process used to be impossible, which indicates a possibility of the widening field of application. Concerning its effect on the energy conservation, energy reduction of several ten thousand tons in heavy oil conversion was predicted by replacing all the existing processes with supercritical fluids. Relating to the recycling, with the use of supercritical fluids, the process is possible which produces higher quality and yield and fewer unnecessary products such as char than the conventional process. 197 refs., 102 figs., 71 tabs.

  20. Gas Path Sealing in Turbine Engines

    Science.gov (United States)

    Ludwig, L. P.

    1978-01-01

    A survey of gas path seals is presented with particular attention given to sealing clearance effects on engine component efficiency. The effects on compressor pressure ratio and stall margin are pointed out. Various case-rotor relative displacements, which affect gas path seal clearances, are identified. Forces produced by nonuniform sealing clearances and their effect on rotor stability are discussed qualitatively, and recent work on turbine-blade-tip sealing for high temperature is described. The need for active clearance control and for engine structural analysis is discussed. The functions of the internal-flow system and its seals are reviewed.

  1. Mechanical seal with textured sidewall

    Energy Technology Data Exchange (ETDEWEB)

    Khonsari, Michael M.; Xiao, Nian

    2017-02-14

    The present invention discloses a mating ring, a primary ring, and associated mechanical seal having superior heat transfer and wear characteristics. According to an exemplary embodiment of the present invention, one or more dimples are formed onto the cylindrical outer surface of a mating ring sidewall and/or a primary ring sidewall. A stationary mating ring for a mechanical seal assembly is disclosed. Such a mating ring comprises an annular body having a central axis and a sealing face, wherein a plurality of dimples are formed into the outer circumferential surface of the annular body such that the exposed circumferential surface area of the annular body is increased. The texture added to the sidewall of the mating ring yields superior heat transfer and wear characteristics.

  2. Study for the Correlation between two tube-sealing fluids and formation of tube excrescence and tube-plugging%两种冲封管方式与锁骨下中心静脉置管导管内赘生物形成及堵管率关系的研究

    Institute of Scientific and Technical Information of China (English)

    王会英; 董风岐; 胡晶敏

    2012-01-01

    目的 探讨肝素钠溶液与生理盐水冲封管方式在锁骨下中心静脉置管(锁穿)导管内赘生物形成及导管堵管率方面的差异.方法 将126例腹部肿瘤锁穿患者按置管顺序随机分为肝素钠组(62人)和生理盐水组(64人),分别给予6~8 ml肝素钠溶液(浓度为50 U/ml)、生理盐水脉冲式冲封管.比较两种冲封管溶液引起的导管内赘生物形成情况、导管留置时间与堵管率等方面是否存在不同.结果 肝素钠组与生理盐水组导管内赘生物情况、导管留置时间差异无显著意义,P>0.05;导管内赘生物情况与导管留置时间呈正相关,r=0.112;两组导管堵管率亦不存在统计学差异,P>0.05.结论 生理盐水冲封管对导管内赘生物情况、导管堵管率等可以起到与肝素钠溶液冲封管相同的效果,且生理盐水符合人体内环境,对血管刺激小,操作简单方便,提高了护理工作的安全性、有效性.%Objective To study the effects of the two different tube-sealing fluids in the formation of tube excrescence and tube-plugging. Method 126 stomach cancer patients with central venous catheter were randomly divided into heparin group and sodium group. For the heparin group, 6~8 ml heparin sodium (50 U/ml) was adopted for sealing trochar, and for the sodium group, 6~8 ml 0. 9% normal saline was adopted for sealing trochar. The difference of tube excrescence and tube-plugging was compared. Result There were no differences in the formation of tube excrescence and the indwelling time between the heparin group and the sodium group(P>0.05). There was positive correlation between the formation of tube excrescence and the indwelling time. And there was no difference in tube-plugging between the two groups(P>0. 05). Conclusion 0. 9% normal saline can achieve the effects of heparin sodium in the formation of tube excrescence and tube-plugging. so the normal saline can replace heparin sodium because of its low price and

  3. Stabilizing geometry for hydrodynamic rotary seals

    Science.gov (United States)

    Dietle, Lannie L.; Schroeder, John E.

    2010-08-10

    A hydrodynamic sealing assembly including a first component having first and second walls and a peripheral wall defining a seal groove, a second component having a rotatable surface relative to said first component, and a hydrodynamic seal comprising a seal body of generally ring-shaped configuration having a circumference. The seal body includes hydrodynamic and static sealing lips each having a cross-sectional area that substantially vary in time with each other about the circumference. In an uninstalled condition, the seal body has a length defined between first and second seal body ends which varies in time with the hydrodynamic sealing lip cross-sectional area. The first and second ends generally face the first and second walls, respectively. In the uninstalled condition, the first end is angulated relative to the first wall and the second end is angulated relative to the second wall. The seal body has a twist-limiting surface adjacent the static sealing lip. In the uninstalled condition, the twist-limiting surface is angulated relative to the peripheral wall and varies along the circumference. A seal body discontinuity and a first component discontinuity mate to prevent rotation of the seal body relative to the first component.

  4. Borehole sealing. Final report, March 1, 1973--October 31, 1973

    Energy Technology Data Exchange (ETDEWEB)

    Eilers, L.H.

    1977-01-01

    A program to evaluate existing materials and techniques to permanently plug boreholes penetrating salt strata near prospective radioactive waste depository sites is described. A new subcontract No. 78X-33542C has been issued to seal a borehole near Lyons, Kansas, using the materials and techniques recommended in this report. It is recommended that the well be thoroughly cleaned including removing any casing penetrating the critical salt strata. Following this, any fluid-bearing zones should be grouted using the best grout available. Silica gel was recommended for porous zones backed up by Portland cement to seal fractures and vugs. Recommendations were made to use sulfate resistant Chem Comp or sulfate resistant regular Portland (Type V) as the primary sealing material in the areas where anhydrite strata are present such as the existing wells at Lyons, Kansas, or the prospective wells near Carlsbad, New Mexico. This would be modified to meet existing conditions such as salt saturated slurry through the salt strata or added powdered silica in the zones which might exceed 230/sup 0/F at any time. A short epoxy plug was recommended at the top and bottom of the salt strata and a short Seal Ring plug at the base of any extensive water zones. Extensive water zones are not expected in the New Mexico area, however.

  5. WIPP shaft seal system parameters recommended to support compliance calculations

    Energy Technology Data Exchange (ETDEWEB)

    Hurtado, L.D.; Knowles, M.K. [Sandia National Labs., Albuquerque, NM (United States); Kelley, V.A.; Jones, T.L.; Ogintz, J.B. [INTERA Inc., Austin, TX (United States); Pfeifle, T.W. [RE/SPEC, Inc., Rapid City, SD (United States)

    1997-12-01

    The US Department of Energy plans to dispose of transuranic waste at the Waste Isolation Pilot Plant (WIPP), which is sited in southeastern New Mexico. The WIPP disposal facility is located approximately 2,150 feet (650 m) below surface in the bedded halite of the Salado Formation. Prior to initiation of disposal activities, the Department of Energy must demonstrate that the WIPP will comply with all regulatory requirements. Applicable regulations require that contaminant releases from the WIPP remain below specified levels for a period of 10,000 years. To demonstrate that the WIPP will comply with these regulations, the Department of Energy has requested that Sandia National Laboratories develop and implement a comprehensive performance assessment of the WIPP repository for the regulatory period. This document presents the conceptual model of the shaft sealing system to be implemented in performance assessment calculations conducted in support of the Compliance Certification Application for the WIPP. The model was developed for use in repository-scale calculations and includes the seal system geometry and materials to be used in grid development as well as all parameters needed to describe the seal materials. These calculations predict the hydrologic behavior of the system. Hence conceptual model development is limited to those processes that could impact the fluid flow through the seal system.

  6. Polarised light stress analysis and laser scatter imaging for non-contact inspection of heat seals in food trays

    OpenAIRE

    Barnes, Michael; Dudbridge, Michael; Duckett, Tom

    2012-01-01

    This paper introduces novel non-contact methods for detecting faults in heat seals of food packages. Two alternative imaging technologies are investigated; laser scatter imaging and polarised light stress images. After segmenting the seal area from the rest of the respective image, a classifier is trained to detect faults in different regions of the seal area using features extracted from the pixels in the respective region. A very large set of candidate features, based on statistical informa...

  7. Rigid bonded glass ceramic seals for high temperature membrane reactors and solid oxide fuel cells

    Energy Technology Data Exchange (ETDEWEB)

    Paulsen, Ove

    2009-05-15

    Solid Oxide Fuel cells (SOFC) and dense gas separation membranes based on mixed ionic and electronic conductors have gained increased interest the resent years due the search for new technologies for clean energy generation. These technologies can be utilized to produce electricity from fossil fuel with low CO{sub 2} emission compared to conventional gas or coal based energy plants. One crucial challenge with high temperature membrane reactors and SOFCs is the sealing of the active membranes/electrolytes to prevent leakage of air to fuel side or vice versa. Due to the high operating temperatures of typical 800-1000 degrees Celsius the selection of reliable sealing materials is limited. The seals have to remain gas tight during the life time of the reactor/SOFC, they need to be chemical compatible with the sealed materials and stable in reducing and oxidizing atmospheres containing water vapour and CO{sub 2}, and finally they should be cheap, readily available and easy to process. The main purpose of the present work was to evaluate rigid bonded glass ceramic seals for dense oxygen ion and proton conducting membranes and electrolytes for SOFCs and high temperature (HT) membrane reactors. First, a review of sealing technologies has been carried out with emphasis on SOFC and ceramic membranes technologies applicable for zero emission power plants. Regarding sealing, the best and cheapest materials at the present time are based on silicate glass and glass ceramics. In the present work aluminate glass without silica is introduced as a new class of seals expanding the material selection for HT membrane sealing technologies. The main reason for studying silica free systems is that silica is known to be unstable in humid atmospheres and/or reducing conditions at elevated temperatures. Two glass systems have been evaluated. The first was based on aluminate glasses in the system RO-CaO-Al{sub 2}O{sub 3} (R=Mg, Ba, Sr) with special focus on the CaO-MgO-Al{sub 2}O{sub 3

  8. Legacy HMSRP Hawaiian Monk Seal Ultrasound Data

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — Ultrasounds measuring the condition of juvenile seals at Laysan Island during 2009-2010, collected when seals were handled as part of the De-Worming Project

  9. HMSRP Hawaiian Monk Seal Entanglement data

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — The data set contains records of all entanglements of Hawaiian monk seals in marine debris. The data set comprises records of seals entangled by derelict fishing...

  10. Film riding seals for rotary machines

    Energy Technology Data Exchange (ETDEWEB)

    Bidkar, Rahul Anil; Sarawate, Neelesh Nandkumar; Wolfe, Christopher Edward; Ruggiero, Eric John; Raj Mohan, Vivek Raja

    2017-03-07

    A seal assembly for a rotary machine is provided. The seal assembly includes multiple sealing device segments disposed circumferentially intermediate to a stationary housing and a rotor. Each of the segments includes a shoe plate with a forward-shoe section and an aft-shoe section having one or more labyrinth teeth therebetween facing the rotor. The sealing device includes a stator interface element having a groove or slot for allowing disposal of a spline seal for preventing segment leakages. The sealing device segment also includes multiple bellow springs or flexures connected to the shoe plate and to the stator interface element. Further, the sealing device segments include a secondary seal integrated with the stator interface element at one end and positioned about the multiple bellow springs or flexures and the shoe plate at the other end.

  11. Legacy HMSRP Hawaiian Monk Seals Observers

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — This data set documents observers that have collected monk seal data as part of the ongoing monk seal population assessment efforts by PSD personnel and cooperating...

  12. HMSRP Hawaiian Monk Seal Crittercam video

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — This project investigates foraging behavior of Hawaiian monk seals by conducting telemetry studies. During these studies, live seals are instrumented with dive...

  13. HMSRP Hawaiian Monk Seal Handling Data

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — This data set contains records for all handling and measurement of Hawaiian monk seals since 1981. Live seals are handled and measured during a variety of events...

  14. Investigation of a Wedge Adhesion Test for Edge Seals

    Energy Technology Data Exchange (ETDEWEB)

    Kempe, Michael; Wohlgemuth, John; Miller, David; Postak, Lori; Booth, Dennis; Phillips, Nancy

    2016-09-26

    Many photovoltaic (PV) technologies have been found to be sensitive to moisture that diffuses into a PV package. Even with the use of impermeable frontsheets and backsheets, moisture can penetrate from the edges of a module. To limit this moisture ingress pathway from occurring, manufacturers often use a low permeability polyisobutylene (PIB) based edge seal filled with desiccant to further restrict moisture ingress. Moisture ingress studies have shown that these materials are capable of blocking moisture for the 25-year life of a module; but to do so, they must remain well-adhered and free of cracks. This work focuses on adapting the Boeing Wedge test for use with edge seals laminated using glass substrates as part of a strategy to assess the long-term durability of edge seals. The advantage of this method is that it duplicates the residual stresses and strains that a glass/glass module may have when the lamination process results in some residual glass bending that puts the perimeter in tension. Additionally, this method allows one to simultaneously expose the material to thermal stress, humidity, mechanical stress, and ultraviolet radiation. The disadvantage of this method generally is that we are limited by the fracture toughness of the glass substrates that the edge seal is adhered to. However, the low toughness of typical uncrosslinked or sparsely crosslinked PIB makes them suitable for this technique. We present data obtained during the development of the wedge test for use with PV edge seal materials. This includes development of the measuring techniques and evaluation of the test method with relevant materials. We find consistent data within a given experiment, along with the theoretical independence of fracture toughness measurements with wedge thickness. This indicates that the test methodology is reproducible. However, even though individual experimental sets are consistent, the reproducibility between experimental sets is poor. We believe this may be

  15. Investigation of a wedge adhesion test for edge seals

    Science.gov (United States)

    Kempe, Michael; Wohlgemuth, John; Miller, David; Postak, Lori; Booth, Dennis; Phillips, Nancy

    2016-09-01

    Many photovoltaic (PV) technologies have been found to be sensitive to moisture that diffuses into a PV package. Even with the use of impermeable frontsheets and backsheets, moisture can penetrate from the edges of a module. To limit this moisture ingress pathway from occurring, manufacturers often use a low permeability polyisobutylene (PIB) based edge seal filled with desiccant to further restrict moisture ingress. Moisture ingress studies have shown that these materials are capable of blocking moisture for the 25-year life of a module; but to do so, they must remain well-adhered and free of cracks. This work focuses on adapting the Boeing Wedge test for use with edge seals laminated using glass substrates as part of a strategy to assess the long-term durability of edge seals. The advantage of this method is that it duplicates the residual stresses and strains that a glass/glass module may have when the lamination process results in some residual glass bending that puts the perimeter in tension. Additionally, this method allows one to simultaneously expose the material to thermal stress, humidity, mechanical stress, and ultraviolet radiation. The disadvantage of this method generally is that we are limited by the fracture toughness of the glass substrates that the edge seal is adhered to. However, the low toughness of typical uncrosslinked or sparsely crosslinked PIB makes them suitable for this technique. We present data obtained during the development of the wedge test for use with PV edge seal materials. This includes development of the measuring techniques and evaluation of the test method with relevant materials. We find consistent data within a given experiment, along with the theoretical independence of fracture toughness measurements with wedge thickness. This indicates that the test methodology is reproducible. However, even though individual experimental sets are consistent, the reproducibility between experimental sets is poor. We believe this may be

  16. Non Destructive Seal Testing Polymeric Tray

    Science.gov (United States)

    2006-10-01

    School of Enviromental and Biological Science Rutgers, The State University of New Jersey New Brunswick, New Jersey 08903 Principal Investigator...strength, tack seals and seal creep. The following modifications were issued : Jan 20, 2004 0008/01 Add incremental funding to increase total...Technologies”. Most of the “commercial off the shelf” systems are designed to detect seal integrity issues , such as seal contamination, cuts and holes. A

  17. Multi-layer seal for electrochemical devices

    Science.gov (United States)

    Chou, Yeong-Shyung [Richland, WA; Meinhardt, Kerry D [Kennewick, WA; Stevenson, Jeffry W [Richland, WA

    2010-09-14

    Multi-layer seals are provided that find advantageous use for reducing leakage of gases between adjacent components of electrochemical devices. Multi-layer seals of the invention include a gasket body defining first and second opposing surfaces and a compliant interlayer positioned adjacent each of the first and second surfaces. Also provided are methods for making and using the multi-layer seals, and electrochemical devices including said seals.

  18. Multi-layer seal for electrochemical devices

    Science.gov (United States)

    Chou, Yeong-Shyung [Richland, WA; Meinhardt, Kerry D [Kennewick, WA; Stevenson, Jeffry W [Richland, WA

    2010-11-16

    Multi-layer seals are provided that find advantageous use for reducing leakage of gases between adjacent components of electrochemical devices. Multi-layer seals of the invention include a gasket body defining first and second opposing surfaces and a compliant interlayer positioned adjacent each of the first and second surfaces. Also provided are methods for making and using the multi-layer seals, and electrochemical devices including said seals.

  19. Pre-sealing risk analysis

    Energy Technology Data Exchange (ETDEWEB)

    Ensminger, D.A.; Hough, M.E.; Oston, S.G.

    1980-01-07

    This report describes studies of accidents involving high-level radioactive waste before sealing the waste into a repository. The report summarizes work done in this area during Fiscal Year 1978 and supplements previous work. Models of accident probability, severity, and consequences are refined and extended.

  20. Predicting Leakage in Labyrinth Seals

    Science.gov (United States)

    Morrison, G. L.; Rhode, D. L.; Cogan, K. C.; Chi, D.; Demko, J.

    1985-01-01

    Analytical and empirical methods evaluated. 264-page report presents comprehensive information on leakage in labyrinth seals. Summarizes previous analyses of leakage, reviews leakage tests conducted by authors and evaluates various analytical and experimental methods of determining leakage and discusses leakage prediction techniques.

  1. 三维地层流体取样和压力测试技术∗%3D Formation Fluid Sampling and Pressure Test Technology

    Institute of Scientific and Technical Information of China (English)

    贺芙邦; 游俊; 刘刚

    2016-01-01

    In order to solve limitations of conventional cable formation test technology, a 3D formation fluid sampling and pressure test technology is developed�The technology can effectively solve technical problems with for⁃mation pressure test and fluid sampling in dense carbonate rocks, tight sandstones and other low permeability for⁃mations, unconsolidated formations and high⁃viscosity fluid formations or under the condition of fluid saturation pressure close to reservoir pressure, and it can greatly reduce the pressure test and fluid sampling time, operation risk and cost�In this paper, advantages of Saturn 3D radial probe are highlighted and site application effects of the probe get analyzed�The Saturn probe has expanded application range of conventional WFT technology�In most ca⁃ses, the Saturn probe can process drilling fluid filtrate and polluted formation fluids more quickly to reduce stay time at measuring points�Compared with standard XLD single probe, the Saturn probe can improve fluid cleaning speed by several orders of magnitude�It is pointed out that the research on 3D formation fluid sampling and pressure test technology has an important practical significance.%针对传统电缆地层测试技术的局限性,开发了三维地层流体取样和压力测试技术。该技术可有效解决致密碳酸盐岩或致密砂岩等低渗地层、未固结地层、含高黏度流体地层,或是流体饱和压力接近储层压力时进行地层压力测试与流体取样面临的诸多技术难题,大大缩短压力测试和流体取样时间,降低作业风险和成本。重点介绍了Saturn三维径向探针的优点,分析了其现场应用效果。 Saturn探针的推出扩大了传统电缆地层测试技术的应用范围,在大多数情况下, Sat⁃urn探针能更快速处理钻井液滤液和受污染的地层流体,从而缩短了在测点上停留的时间,与标准XLD单探针相比, Saturn探针完成流体清

  2. 深层水平井双聚胺基钻井液技术研究与应用%Research and Application of Double Poly Amine Drilling Fluid Technology in Deep Horizontal Well

    Institute of Scientific and Technical Information of China (English)

    刘永贵; 张洋; 徐用军

    2015-01-01

    drilling, the technical measures for drilling fluid were clear.Though the study on inhibition of polyamine&polyether polyol and anti-sloughing plugging agent and working with new efficient independent developed drilling sealing material, a set of double poly amine drilling fluid technology was developed, which is suitable for horizontal well construction in deep tight gas reservoir.The laboratory studies and field ap-plication show that this drilling fluid system has ability of strong sealing & anti-collapse, hole cleaning, lubricating and sticking prevention, it can be used at the temperature more than 180℃.A series of complex problems and the reservoir protection in deep horizontal well drilling were effectively solved.New records were created for deep horizontal well drilling in Daqing oilfield, the shortest drilling cycle(109 d),the deepest depth(5048 m),the longest horizontal section(969.22 m) and the highest working temperature (180 ℃) at the hole bottom, which completely satisfy the requirements of drilling in deep tight gas reservoir in Xujiaweizi area and provide the technical support for safe, fast and efficient drilling in the deep horizontal well.

  3. Aerodynamic seal assemblies for turbo-machinery

    Energy Technology Data Exchange (ETDEWEB)

    Bidkar, Rahul Anil; Wolfe, Christopher; Fang, Biao

    2015-09-29

    The present application provides an aerodynamic seal assembly for use with a turbo-machine. The aerodynamic seal assembly may include a number of springs, a shoe connected to the springs, and a secondary seal positioned about the springs and the shoe.

  4. Piston rod seal for a Stirling engine

    Science.gov (United States)

    Shapiro, Wilbur

    1984-01-01

    In a piston rod seal for a Stirling engine, a hydrostatic bearing and differential pressure regulating valve are utilized to provide for a low pressure differential across a rubbing seal between the hydrogen and oil so as to reduce wear on the seal.

  5. Ergonomics and safety of manual bag sealing.

    NARCIS (Netherlands)

    Groot, M.D. de; Bosch, T.; Eikhout, S.M.; Vink, P.

    2005-01-01

    A variety of seals is used to close bags. Each seal has advantages and disadvantages. For shop assistants sealing bags could be a repetitive physically demanding action. Opening and closing the bags again can cause some discomfort or annoyance for consumers. Besides, it is an activity which can enda

  6. Oriented cluster perforating technology and its application in horizontal wells

    Directory of Open Access Journals (Sweden)

    Huabin Chen

    2016-11-01

    Full Text Available An oriented cluster perforating technology, which integrates both advantages of cluster and oriented perforating, will help solve a series of technical complexities in horizontal well drilling. For realizing its better application in oil and gas development, a series of technologies were developed including perforator self-weight eccentricity, matching of the electronic selective module codes with the surface program control, axial centralized contact signal transmission, and post-perforation intercluster sealing insulation. In this way, the following functions could be realized, such as cable-transmission horizontal well perforator self-weight orientation, dynamic signal transmission, reliable addressing & selective perforation and post-perforation intercluster sealing. The combined perforation and bridge plug or the multi-cluster perforation can be fulfilled in one trip of perforation string. As a result, the horizontal-well oriented cluster perforating technology based on cable conveying was developed. This technology was successfully applied in unconventional gas reservoir exploitation, such as shale gas and coalbed methane, with accurate orientation, reliable selective perforation and satisfactory inter-cluster sealing. The horizontal-well oriented cluster perforating technology benefits the orientation of horizontal well drilling with a definite target and direction, which provides a powerful support for the subsequent reservoir stimulation. It also promotes the fracturing fluid to sweep the principal pay zones to the maximum extent. Moreover, it is conductive to the formation of complex fracture networks in the reservoirs, making quality and efficient development of unconventional gas reservoirs possible.

  7. 汽车自动变速器油的技术现状与发展趋势%Current Technology and Development Trends of Automatic Transmission Fluids

    Institute of Scientific and Technical Information of China (English)

    李茂生; 杜群贵; 贾继欣

    2014-01-01

    The types,characteristics and developing direction of vehicle automatic transmission,and the technical re-quirement,current technological state and development trend of automatic transmission fluids (ATF/CVTF ) were de-scribed.The tribological characteristics and evaluation method of ATF/CVTF were introduced.The development and appli-cation of new automatic transmission fluids and its corresponding evaluation test methods of physical and chemical proper-ties,friction characteristics and wear state,the development of the specifications and standard of automatic transmission flu-ids are key common technologies for development of automatic transmission.%论述汽车自动变速器(AT、CVT)的类型、特点及发展方向,以及与其配套的变速器油(ATF、CVTF)的技术现状和发展趋势,介绍ATF/CVTF的摩擦学特性及其评价方法。开发和应用新型自动变速器油及其相应的摩擦特性测试方法、磨损状态评定手段和油品理化性能测试方法及台架试验方法,制定自动变速器油的规格标准,是促进自动变速器发展的关键共性技术。

  8. Computation of rotordynamic coefficients associated with leakage steam flow through labyrinth seal

    Energy Technology Data Exchange (ETDEWEB)

    Wang, W.Z.; Liu, Y.Z.; Chen, H.P. [Shanghai Jiaotong University, Thermal Fluid Flow and Turbomachinery Lab., School of Mechanical Engineering, Shanghai (China); Jiang, P.N. [Shanghai Turbine Company, Department of R and D, Shanghai (China)

    2007-08-15

    A mathematical model of calculating rotordynamic coefficients associated with leakage steam flow through labyrinth seals was presented. Particular attention was given to incorporating thermal properties of the steam fluid into prediction of leakage flow and subsequent derivation of rotordynamic coefficients, which quantitatively characterize influence of aerodynamic forcing of the leakage steam flow on the rotordynamics. By using perturbation analysis, we determined periodic and analytic solutions of the continuity and circumferential momentum equations for the time-dependent flow induced by non-axisymmetric rotation of the rotor encompassed by a labyrinth seal. Pressure distributions along labyrinth seal cavities and rotordynamic coefficients were compared at the same condition for air and steam flows. Influence of steam flow through the labyrinth seal cavities on rotordynamic coefficients was analyzed in terms of inlet pressure, inlet swirl velocity and rotor speed. (orig.)

  9. A hydrodynamically suspended, magnetically sealed mechanically noncontact axial flow blood pump: design of a hydrodynamic bearing.

    Science.gov (United States)

    Mitamura, Yoshinori; Kido, Kazuyuki; Yano, Tetsuya; Sakota, Daisuke; Yambe, Tomoyuki; Sekine, Kazumitsu; OKamoto, Eiji

    2007-03-01

    To overcome the drive shaft seal and bearing problem in rotary blood pumps, a hydrodynamic bearing, a magnetic fluid seal, and a brushless direct current (DC) motor were employed in an axial flow pump. This enabled contact-free rotation of the impeller without material wear. The axial flow pump consisted of a brushless DC motor, an impeller, and a guide vane. The motor rotor was directly connected to the impeller by a motor shaft. A hydrodynamic bearing was installed on the motor shaft. The motor and the hydrodynamic bearing were housed in a cylindrical casing and were waterproofed by a magnetic fluid seal, a mechanically noncontact seal. Impeller shaft displacement was measured using a laser sensor. Axial and radial displacements of the shaft were only a few micrometers for motor speed up to 8500 rpm. The shaft did not make contact with the bearing housing. A flow of 5 L/min was obtained at 8000 rpm at a pressure difference of 100 mm Hg. In conclusion, the axial flow blood pump consisting of a hydrodynamic bearing, a magnetic fluid seal, and a brushless DC motor provided contact-free rotation of the impeller without material wear.

  10. Dual function seal: visualized digital signature for electronic medical record systems.

    Science.gov (United States)

    Yu, Yao-Chang; Hou, Ting-Wei; Chiang, Tzu-Chiang

    2012-10-01

    Digital signature is an important cryptography technology to be used to provide integrity and non-repudiation in electronic medical record systems (EMRS) and it is required by law. However, digital signatures normally appear in forms unrecognizable to medical staff, this may reduce the trust from medical staff that is used to the handwritten signatures or seals. Therefore, in this paper we propose a dual function seal to extend user trust from a traditional seal to a digital signature. The proposed dual function seal is a prototype that combines the traditional seal and digital seal. With this prototype, medical personnel are not just can put a seal on paper but also generate a visualized digital signature for electronic medical records. Medical Personnel can then look at the visualized digital signature and directly know which medical personnel generated it, just like with a traditional seal. Discrete wavelet transform (DWT) is used as an image processing method to generate a visualized digital signature, and the peak signal to noise ratio (PSNR) is calculated to verify that distortions of all converted images are beyond human recognition, and the results of our converted images are from 70 dB to 80 dB. The signature recoverability is also tested in this proposed paper to ensure that the visualized digital signature is verifiable. A simulated EMRS is implemented to show how the visualized digital signature can be integrity into EMRS.

  11. Technology of complex new type of viscous fluids/short fibers%新型粘流体/短纤维复合生产工艺

    Institute of Scientific and Technical Information of China (English)

    霍力超

    2012-01-01

    本文介绍了一种使用双螺杆聚合反应器替代传统生产装置,解决现有粘流体掺混生产周期长、真空脱气不彻底、不易放料等工艺技术难题.讨论了生产工艺对粘流体/短纤维复合产品的影响因素和产品稳定性.%The traditional device was displaced by twin screw reactor for polymerization to solve the problems of long production cycle of viscous fluids, vacuum degassing incompletely and feed hard. The effect influence and stability of technology to viscous fluids/short fibers were discussed.

  12. Symmetries in Images on Ancient Seals

    CERN Document Server

    Sparavigna, Amelia

    2008-01-01

    In this paper, we discuss the presence of symmetries in images engraved on ancient seals, in particular on stamp seals. Mainly used to secure the containers from tampering and for owner's identification, these objects appeared during the 5th millennium BC in Mesopotamia. Usually the seals were engraved with simple images, suitable to communicate an immediate information. Rotational symmetries are already displayed by the most ancient stamp seals, whose images reach a quasi-perfect symmetry in their small circular or ovoid spaces. Bilateral symmetries are quite common in Egyptian scarab seals.

  13. Choice of rotatable plug seals for prototype fast breeder reactor: Review of historical perspectives

    Energy Technology Data Exchange (ETDEWEB)

    Sinha, N.K., E-mail: nksinha@igcar.gov.in; Raj, Baldev, E-mail: baldev.dr@gmail.com

    2015-09-15

    Highlights: • Choice and arrangement of elastomeric inflatable and backup seals as primary and secondary barriers. • With survey (mid-1930s onwards) of reactor, sealing, R&D and rubber technology. • Load, reliability, safety, life and economy of seals and reactors are key factors. • PFBR blends concepts and experience of MOX fuelled FBRs with original solutions. • R&D indicates inflatable seal advanced fluoroelastomer pivotal in unifying nuclear sealing. - Abstract: Choice and arrangement of elastomeric primary inflatable and secondary backup seals for the rotatable plugs (RPs) of 500 MW (e), sodium cooled, pool type, 2-loop, mixed oxide (MOX) fuelled Prototype Fast Breeder Reactor (PFBR) is depicted with review of various historical perspectives. Static and dynamic operation, largest diameters (PFBR: ∼6.4 m, ∼4.2 m), widest gaps and variations (5 ± 2 mm) and demanding operating requirements make RP openings on top shield (TS) the most difficult to seal which necessitated extensive development from 1950s to early 1990s. Liquid metal freeze seals with life equivalent to reactor prevailed as primary barrier (France, Japan, U.S.S.R.) during pre-1980s in spite of bulk, cost and complexity due to the abilities to meet zero leakage and resist core disruptive accident (CDA). Redefinition of CDA as beyond design basis accident, tolerable leakage and enhanced economisation drive during post-1980s established elastomeric inflatable seal as primary barrier excepting in U.S.S.R. (MOX fuel, freeze seal) and U.S.A. (metallic fuel). Choice of inflatable seal for PFBR RPs considers these perspectives, inherent advantages of elastomers and those of inflatable seals which maximise seal life. Choice of elastomeric backup seal as secondary barrier was governed by reliability and minimisation as well as distribution of load (temperature, radiation, mist) to maximise seal life. The compact sealing combination brings the hanging RPs at about the same elevation to reduce

  14. Standard Test Method for Testing Polymeric Seal Materials for Geothermal and/or High Temperature Service Under Sealing Stress

    CERN Document Server

    American Society for Testing and Materials. Philadelphia

    1985-01-01

    1.1 This test method covers the initial evaluation of (screening) polymeric materials for seals under static sealing stress and at elevated temperatures. 1.2 This test method applies to geothermal service only if used in conjunction with Test Method E 1068. 1.3 The test fluid is distilled water. 1.4 The values stated in SI units are to be regarded as the standard. The values in parentheses are for information only. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

  15. Repository Sealing Program Plan: repository in salt

    Energy Technology Data Exchange (ETDEWEB)

    Kelsall, P.C.; Coons, W.E.; Meyer, D.

    1983-01-01

    The isolation of nuclear wastes in deep, mined repositories will require the sealing of all penetrations such as shafts, tunnels, or boreholes into or nearby the repository. This Repository Sealing Program Plan describes the technical programs required to complete seal designs for a repository in salt prior to license application in 1988. The plan examines the current schematic seal designs for a repository in salt and identifies seven major technical programs which are required to advance the designs to the status required for licensing: (1) update designs to incorporate site-specific geologic and hydrologic characteristics; (2) reference designs to site-specific repository designs; (3) develop site-specific performance requirements; (4) salt consolidation testing and modeling; (5) materials development; (6) design analyses; (7) verification testing. Scedules for each of these programs are keyed to governing seal design and ONWI milestones. Conceptual seal designs will be completed in FY 84 and preliminary seal designs in FY 87.

  16. Air riding seal with purge cavity

    Energy Technology Data Exchange (ETDEWEB)

    Sexton, Thomas D; Mills, Jacob A

    2017-08-15

    An air riding seal for a turbine in a gas turbine engine, where an annular piston is axial moveable within an annular piston chamber formed in a stator of the turbine and forms a seal with a surface on the rotor using pressurized air that forms a cushion in a pocket of the annular piston. A purge cavity is formed on the annular piston and is connected to a purge hole that extends through the annular piston to a lower pressure region around the annular piston or through the rotor to an opposite side. The annular piston is sealed also with inner and outer seals that can be a labyrinth seal to form an additional seal than the cushion of air in the pocket to prevent the face of the air riding seal from overheating.

  17. Rotary seal with improved film distribution

    Energy Technology Data Exchange (ETDEWEB)

    Dietle, Lannie Laroy; Schroeder, John Erick

    2015-09-01

    The present invention is a generally circular rotary seal that establishes sealing between relatively rotatable machine components for lubricant retention and environmental exclusion, and incorporates seal geometry that interacts with the lubricant during relative rotation to distribute a lubricant film within the dynamic sealing interface. The features of a variable inlet size, a variable dynamic lip flank slope, and a reduction in the magnitude and circumferentially oriented portion of the lubricant side interfacial contact pressure zone at the narrowest part of the lip, individually or in combination thereof, serve to maximize interfacial lubrication in severe operating conditions, and also serve to minimize lubricant shear area, seal torque, seal volume, and wear, while ensuring retrofitability into the seal grooves of existing equipment.

  18. Rotary seal with improved film distribution

    Science.gov (United States)

    Dietle, Lannie Laroy; Schroeder, John Erick

    2013-10-08

    The present invention is a generally circular rotary seal that establishes sealing between relatively rotatable machine components for lubricant retention and environmental exclusion, and incorporates seal geometry that interacts with the lubricant during relative rotation to distribute a lubricant film within the dynamic sealing interface. The features of a variable inlet size, a variable dynamic lip flank slope, and a reduction in the magnitude and circumferentially oriented portion of the lubricant side interfacial contact pressure zone at the narrowest part of the lip, individually or in combination thereof, serve to maximize interfacial lubrication in severe operating conditions, and also serve to minimize lubricant shear area, seal torque, seal volume, and wear, while ensuring retrofitability into the seal grooves of existing equipment.

  19. Seal dynamics on the Swedish west coast: Scenarios of competition as Baltic grey seal intrude on harbour seal territory

    Science.gov (United States)

    Svensson, Carl Johan

    2012-07-01

    The Kattegat-Skagerrak region on the Swedish west coast is home to an abundant harbour seal population (Phoca vitulina) and a small scattered grey seal population (Halichoerus grypus). In addition, grey seal from the growing population in the Baltic Sea frequently migrate into the Kattegat-Skagerrak. Harbour seals on the west coast of Sweden show relatively high population growth (approximately 9%) compared to the Baltic grey seal in ice-free habitats (approximately 6%), which, in theory, makes harbour seal the stronger competitor of the two in this region. However, incidents of disease in harbour seals that lower population growth are becoming more frequent. These epidemics are primarily caused by the Phocine Distemper Virus (PDV), and may reduce population size with up to 70%. This study models the average development under potential scenarios of competing harbour- and Baltic grey seal populations using Leslie matrices and the Lotka-Volterra model of inter-specific competition. The model is parameterised with previously published data, and resource overlap is incorporated through density dependent pup survival. Using numerical methods short- and long-term abundances are simulated under weak, moderate and strong competition and for different frequencies of PDV epidemics. Results show that the harbour seals are resilient to competition while exerting a negative effect on grey seal abundance under moderate to strong competition. Hence Baltic grey seal benefit from weaker levels of competition. Under moderate and strong competition grey seal abundance is a direct function of the PDV frequency as this reduces the competitive strength of harbour seals. Theoretically this means that higher frequencies of PDV or other pathogens epidemics could facilitate an expansion of Baltic grey seal into Kattegat-Skagerrak. Independent of interaction strength and frequency of epidemics the projected changes to abundances are slow (50-100 years), and even in exceedingly stable

  20. Ceramic Borehole Seals for Nuclear Waste Disposal Applications

    Science.gov (United States)

    Lowry, B.; Coates, K.; Wohletz, K.; Dunn, S.; Patera, E.; Duguid, A.; Arnold, B.; Zyvoloski, G.; Groven, L.; Kuramyssova, K.

    2015-12-01

    Sealing plugs are critical features of the deep borehole system design. They serve as structural platforms to bear the weight of the backfill column, and as seals through their low fluid permeability and bond to the borehole or casing wall. High hydrostatic and lithostatic pressures, high mineral content water, and elevated temperature due to the waste packages and geothermal gradient challenge the long term performance of seal materials. Deep borehole nuclear waste disposal faces the added requirement of assuring performance for thousands of years in large boreholes, requiring very long term chemical and physical stability. A high performance plug system is being developed which capitalizes on the energy of solid phase reactions to form a ceramic plug in-situ. Thermites are a family of self-oxidized metal/oxide reactions with very high energy content and the ability to react under water. When combined with engineered additives the product exhibits attractive structural, sealing, and corrosion properties. In the initial phase of this research, exploratory and scaled tests demonstrated formulations that achieved controlled, fine grained, homogeneous, net shape plugs composed predominantly of ceramic material. Laboratory experiments produced plug cores with confined fluid permeability as low as 100 mDarcy, compressive strength as high as 70 MPa (three times the strength of conventional well cement), with the inherent corrosion resistance and service temperature of ceramic matrices. Numerical thermal and thermal/structural analyses predicted the in-situ thermal performance of the reacted plugs, showing that they cooled to ambient temperature (and design strength) within 24 to 48 hours. The current development effort is refining the reactant formulations to achieve desired performance characteristics, developing the system design and emplacement processes to be compatible with conventional well service practices, and understanding the thermal, fluid, and structural

  1. Mechanical Deformation of Ship Stern-Shaft Mechanical Face Seals

    Institute of Scientific and Technical Information of China (English)

    朱汉华; 刘正林; 温诗铸; 严新平

    2004-01-01

    In ship propeller shaft systems, the shaft seal is a mechanical face seal, which includes a stationary metal seal ring and a rotating ring.The seal faces are deformed with different loads.The deformation of the seal faces affects the performance of mechanical face seals, which leads to water leakage, so the seal face deformation must be analyzed.A mechanics model with deformation equations was developed to describe ship stern-shaft seals.An example was given to verify the deformation equations.The solution of the deformation equations gives a theoretical basis for the analysis of seal leakage and improvements of seal structures.

  2. Seal designing of theodolite used in seaside environment

    Science.gov (United States)

    Jin, Humin; Yan, Xiaoxu; Hao, Wei; Zhou, Sizhong

    2014-08-01

    Based on the environment requirements in seaside there exists static and dynamic seal designing for the photoelectric Theodolite. Static seal designing emphatically includes the designing of o-ring size and mechanical property analysis of o-ring seal, which is difficult to adopt conventional dynamic seal to meet the requirements. According to practical application, the combination of the radial labyrinth seal and high quality felt seal are designed. The combination seal which better solves the seal problem of narrow radial size is a good way of dynamic seal. At the same time, there is engineering practice needing to proof the radial labyrinth seal.

  3. Analysis of TNF-α-induced Leukocyte Adhesion to Vascular Endothelial Cells Regulated by Fluid Shear Stress Using Microfluidic Chip-based Technology

    Institute of Scientific and Technical Information of China (English)

    LI Yuan; YANG De-yu; LIAO Juan; GONG Fang; HE Ping; LIU Bei-zhong

    2015-01-01

    This paper aims to the research of the impact of fluid shear stress on the adhesion between vascular endothelial cells and leukocyte induced by tumor necrosis factor-α(TNF-α) by microfliudic chip technology. Microfluidic chip was fabricated by soft lithograph;Endothelial microfluidic chip was constructed by optimizing types of the extracellular matrix proteins modified in the microchannel and cell incubation time;human umbilical vein endothelial cells EA.Hy926 lined in the microchannel were exposed to fluid shear stress of 1.68 dynes/cm2 and 8.4 dynes/cm2 respectively. Meanwhile, adhesion between EA.Hy926 cells and leukocyte was induced by TNF-αunder a flow condition. EA. Hy926 cell cultured in the static condition was used as control group. The numbers of fluorescently-labeled leukocyte in microchannel were counted to quantize the adhesion level between EA. Hy926 cells and leukocyte; cell immunofluorescence technique was used to detect the intercellular adhesion molecule (ICAM-1) expression. The constructed endothelial microfluidic chip can afford to the fluid shear stress and respond to exogenous stimulus of TNF-α;compared with the adhesion numbers of leukocyte in control group, adhesion between EA. Hy926 cells exposed to low fluid shear stress and leukocyte was reduced under the stimulus of TNF-α at a concentration of 10 ng/ml(P<0.05);leukocyte adhesion with EA. Hy926 cells exposed to high fluid shear stress was reduced significantly than EA. Hy926 cells in control group and EA.1Hy926 cells exposed to low fluid shear stress ( P<0.01); the regulation mechanism of fluid shear stress to the adhesion between EA. Hy926 cells and leukocyte induced by TNF-αwas through the way of ICAM-1. The endothelial microfluidic chip fabricated in this paper could be used to study the functions of endothelial cell in vitro and provide a new technical platform for exploring the pathophysiology of the related cardiovascular system diseases under a flow environment.

  4. Comparison Research on Performance of Labyrinth-like Screw Seal and Labyrinth Seal%类迷宫螺旋密封与迷宫密封的性能对比研究

    Institute of Scientific and Technical Information of China (English)

    高远; 王凡; 张秀珩; 焦圳; 崔淮

    2014-01-01

    往复式压缩机迷宫密封加工过程中,为简化加工工艺,将传统迷宫密封加工成类迷宫螺旋密封。为比较类迷宫螺旋密封与迷宫密封的密封性能差异,分析类迷宫螺旋密封的密封机制,将类迷宫螺旋密封的能量耗散分成类迷宫密封能量耗散和槽向能量损失,采用CFD方法对类迷宫螺旋密封的密封性能进行数值模拟。结果表明,类迷宫螺旋密封的密封性能虽不及传统迷宫密封,但密封效果相差在5%以内,综合考虑加工工艺、经济效益等因素,采用类迷宫螺旋密封代替迷宫密封是完全可行的。%To simplify the processing technology,the labyrinth-like screw seal is used to replace the traditional labyrinth seal during the machining process of labyrinth reciprocating compressor.The sealing performance between the labyrinth seal and the labyrinth-like screw seal was compared,and the sealing mechanism of labyrinth-like screw seal was analyzed.By dividing the energy dissipation of labyrinth-like screw seal into the energy dissipation of labyrinth-like seal and the energy loss at groove direction,the sealing performance of the labyrinth-like screw seal was simulated by using CFD method.The results show that the sealing performance of the labyrinth-like screw seal is less than that of traditional labyrinth seal,but the sealing effect difference is within 5%.It is completely feasible to use the labyrinth-like screw seal instead of the laby-rinth seal with considering processing technology,economic benefit and other factors.

  5. Hermetic seal for a shaft

    Science.gov (United States)

    Lombardi, F. (Inventor)

    1982-01-01

    An hermetic seal for a linear rod having a portion thereof projected axially through a port defined in a wall for a pressure chamber and supported thereby for omni-directional motion is described. The seal is characterized by a resilient, impervious, cylindrical body having a first section concentrically related to the shaft and integrally affixed thereto comprising a linear ordered array of annular flutes. A second section integrally is affixed to the wall of the chamber and concentrically related to the port comprising a second linear ordered array of annular flutes. A third section is interposed between the first and second sections and integrally affixed in coaxial alignment therewith comprising an annular ordered array of linear flutes concentrically related to the shaft, whereby axial, angular, and pivotal motion of the rod is accommodated.

  6. Baseline System Costs for 50.0 MW Enhanced Geothermal System -- A Function of: Working Fluid, Technology, and Location, Location, Location

    Energy Technology Data Exchange (ETDEWEB)

    Dunn, Paul [Gas Equipment Engineering Corp., Milford, CT (United States); Selman, Nancy [Gas Equipment Engineering Corp., Milford, CT (United States); Volpe, Anthony Della [Gas Equipment Engineering Corp., Milford, CT (United States); Moss, Deborah [Gas Equipment Engineering Corp., Milford, CT (United States); Mobley, Rick [Plasma Energy Services, LLC, Putnam, CT (United States); Dickey, Halley [Turbine Air Systems, Houston, TX (United States); Unruh, Jeffery [Fugro NV/Wm. Lettis & Associates, Houston, TX (United States); Hitchcock, Chris [Fugro NV/Wm. Lettis & Associates, Houston, TX (United States); Tanguay, Jasmine [Conservation Law Foundation/CLF Ventures, Boston, MA (United States); Larsen, Walker [Conservation Law Foundation/CLF Ventures, Boston, MA (United States); Sanyal, Sabir [GeothermEx, Inc., San Pablo, CA (United States); Butler, Steven [GeothermEx, Inc., San Pablo, CA (United States); Stacey, Robert [GeothermEx, Inc., San Pablo, CA (United States); Robertson-Tait, Ann [GeothermEx, Inc., San Pablo, CA (United States); Pruess, Karsten [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Gutoski, Greg [Fairbanks Morse Engines (FME), Beloit, WI (United States); Fay, Jamie M. [Fort Point Associates, Boston, MA (United States); Stitzer, John T. [Fort Point Associates, Boston, MA (United States); Oglesby, Ken [Impact Technologies LLC, Tulsa, OK (United States)

    2012-04-30

    Substantial unexploited opportunity exists for the US, and the world, in Enhanced Geothermal Systems (EGS). As a result of US DOE investment, new drilling technology, new power generation equipment and cycles enable meaningful power production, in a compact and modular fashion; at lower and lower top side EGS working fluid temperatures and in a broader range of geologies and geographies. This cost analysis effort supports the expansion of Enhanced Geothermal Systems (EGS), furthering DOE strategic themes of energy security and sub goal of energy diversity; reducing the Nation's dependence on foreign oil while improving the environment.

  7. Nonlinear dynamic analysis of a rotor-bearing-seal system under two loading conditions

    Science.gov (United States)

    Ma, Hui; Li, Hui; Niu, Heqiang; Song, Rongze; Wen, Bangchun

    2013-11-01

    The operating speed of the rotating machinery often exceeds the second or even higher order critical speeds to pursue higher efficiency. Thus, how to restrain the higher order mode instability caused by the nonlinear oil-film force and seal force at high speed as far as possible has become more and more important. In this study, a lumped mass model of a rotor-bearing-seal system considering the gyroscopic effect is established. The graphite self-lubricating bearing and the sliding bearing are simulated by a spring-damping model and a nonlinear oil-film force model based on the assumption of short bearings, respectively. The seal is simulated by Muszynska nonlinear seal force model. Effects of the seal force and oil-film force on the first and second mode instabilities are investigated under two loading conditions which are determined by API Standard 617 (Axial and Centrifugal Compressors and Expander-compressors for Petroleum, Chemical and Gas Industry Services, Seventh Edition). The research focuses on the effects of exciting force forms and their magnitudes on the first and second mode whips in a rotor-bearing-seal system by using the spectrum cascades, vibration waveforms, orbits and Poincaré maps. The first and second mode instability laws are compared by including and excluding the seal effect in a rotor system with single-diameter shaft and two same discs. Meanwhile, the instability laws are also verified in a rotor system with multi-diameter shaft and two different discs. The results show that the second loading condition (out-of-phase unbalances of two discs) and the nonlinear seal force can mainly restrain the first mode instability and have slight effects on the second mode instability. This study may contribute to a further understanding about the higher order mode instability of such a rotor system with fluid-induced forces from the oil-film bearings and seals.

  8. Fiscal 1995 research investigation on chemical process technology using supercritical fluid; 1995 nendo chorinkai ryutai wo riyoshita kagaku process gijutsu ni kansuru chosa kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-03-01

    With relation to the supercritical fluid utilization technology, conducted in fiscal 1995 were collection of basic data, extraction of R and D subjects and survey/analysis of application fields based on the literature survey and overseas field survey. From the research results, the following were selected as research subjects: as to the clean/recycling process technology, non-selection cascade treatment process of mixed waste plastics, hazardous waste treatment process, and radioactive waste treatment process. As to the unused resource utilization process technology, the supercritical submerged combustion power generation process, heavy hydrocarbon resource reutilization process, biomass synthetic utilization process, and carbon dioxide reutilization process. As to the next generation reaction process technology, the simple reaction process, de-organic solvent process, chemical materialization process for methane, and reaction separation combined process. As the innovative material process technology, the plastic forming process, high-functional materials, high-efficiency energy conversion materials, and heightening of function of solid wastes. 537 refs., 116 figs., 54 tabs.

  9. Supercritical fluid chromatography of fish, shark and seal oils

    DEFF Research Database (Denmark)

    Borch-Jensen, Christina; Mollerup, Jørgen

    1996-01-01

    esters, cholesterol esters, diglycerides, triglycerides and ether lipids. Methods for the analysis of the marine oils depend on components present in the oil. When co-eluting lipid groups were present, modifications such as hydrogenation or TLC fractionation of the oils had to be made. In this paper...

  10. 严重大面积软组织缺损后负压封闭引流技术的护理%Nursing of severe extensive soft tissue injuries with vacuum sealing drainage technology

    Institute of Scientific and Technical Information of China (English)

    殷素凤

    2012-01-01

    目的 探索严重大面积软组织缺损后持续负压封闭吸引技术的护理.方法 回顾分析对24例严重大面积软组织损伤患者的护理,使用持续负压封闭吸引技术,保持有效引流,做好心理护理、疼痛护理、饮食护理等.结果 所有病例均治愈,无护理并发症发生.结论 术后有效的负压封闭引流、创面的正确观察、适当的心理护理、及时的营养支持等是护理的关键环节.%Objective To explore the nursing strategies for severe extensive soft tissue injuries with vacuum sealing drainage (VSD). Methods The nursing data of 24 patients with severe extensive soft tissue injuries treated with constant VSD were retrospectively analyzed. Effective and constant drainage, psychological nursing, pain nursing and diet nursing were properly administered. Results All patients were cured without any nursing complications. Conclusion Constant vacuum sealing drainage, correct wounds observation, proper psychological nursing and in- time nutritional support after surgery are key steps of nursing.

  11. Performance evaluation study of IHX-IV seal assembly

    Energy Technology Data Exchange (ETDEWEB)

    Padmakumar, G.; Venkatramanan, J.; Balasubramanian, V.; Prakash, V.; Vaidyanathan, G. [Indira Gandhi Centre for Atomic Research, Kalpakkam - 603102 (India); Konnur, M.S.; Ram Mohan, S.; Suresh, M.; Manikandan, S.; Rajesh, V. [Fluid Control Research Institute, Palakkad - 678 623 (India)

    2005-07-01

    Full text of publication follows: The construction of the 500 MWe Prototype Fast Breeder Reactor (PFBR) has commenced at IGCAR, Kalpakkam. PFBR has four intermediate Heat Exchangers (IHX) and two primary Sodium Pumps. The secondary circuits consist of two loops with each loop having one secondary pump, two intermediate heat exchangers, one surge tank and four steam generators. Primary circuit has both hot and cold sodium and is separated into hot and cold pools by Inner Vessel(IV). IHX forms the interface between the primary circuit and secondary circuit of PFBR. The IHX and pumps are supported from at the top in the roof slab and penetrate through the conical portion of inner vessel. Proper sealing arrangements are necessary to prevent leakage of hot sodium into the cold pool through the penetration. The Mechanical Seal is employed to minimize the leakage through the penetration. This seal arrangement can facilitate Differential radial and thermal expansion between IHX and IV stand pipe at the region of penetration Relative tilting between the axis of IHX and IV stand pipe Smooth installation during commissioning and easy removal during maintenance Minimizes the forces transmitted to IV The hydraulic simulation study, of the IHX - IV mechanical seal assembly was undertaken at the Fluid Control Research Institute, Palghat. The seal has two leakage paths viz. Axial and radial. The leakage depends on the contact pressure on the sealing surface and the head causing the leakage. High leakage flow may lead to damage of inner vessel and may affect the thermal efficiency of the IHX. CFD analysis of the geometry was done in detail. This was done for prototype and the model condition. The optimized design obtained using CFD was employed for experimental evaluation. In the experimental set up, the leakage characteristics was studied for varying axial and radial clearance that prevails during the various stages of operation of the seal assembly in the reactor. A 1/2 scaled

  12. Nanofiltration across Defect-Sealed Nanoporous Monolayer Graphene.

    Science.gov (United States)

    O'Hern, Sean C; Jang, Doojoon; Bose, Suman; Idrobo, Juan-Carlos; Song, Yi; Laoui, Tahar; Kong, Jing; Karnik, Rohit

    2015-05-13

    Monolayer nanoporous graphene represents an ideal membrane for molecular separations, but its practical realization is impeded by leakage through defects in the ultrathin graphene. Here, we report a multiscale leakage-sealing process that exploits the nonpolar nature and impermeability of pristine graphene to selectively block defects, resulting in a centimeter-scale membrane that can separate two fluid reservoirs by an atomically thin layer of graphene. After introducing subnanometer pores in graphene, the membrane exhibited rejection of multivalent ions and small molecules and water flux consistent with prior molecular dynamics simulations. The results indicate the feasibility of constructing defect-tolerant monolayer graphene membranes for nanofiltration, desalination, and other separation processes.

  13. Combining microwave resonance technology to multivariate data analysis as a novel PAT tool to improve process understanding in fluid bed granulation.

    Science.gov (United States)

    Lourenço, Vera; Herdling, Thorsten; Reich, Gabriele; Menezes, José C; Lochmann, Dirk

    2011-08-01

    A set of 192 fluid bed granulation batches at industrial scale were in-line monitored using microwave resonance technology (MRT) to determine moisture, temperature and density of the granules. Multivariate data analysis techniques such as multiway partial least squares (PLS), multiway principal component analysis (PCA) and multivariate batch control charts were applied onto collected batch data sets. The combination of all these techniques, along with off-line particle size measurements, led to significantly increased process understanding. A seasonality effect could be put into evidence that impacted further processing through its influence on the final granule size. Moreover, it was demonstrated by means of a PLS that a relation between the particle size and the MRT measurements can be quantitatively defined, highlighting a potential ability of the MRT sensor to predict information about the final granule size. This study has contributed to improve a fluid bed granulation process, and the process knowledge obtained shows that the product quality can be built in process design, following Quality by Design (QbD) and Process Analytical Technology (PAT) principles.

  14. Supercritical Fluid Technology and Chemical Process Intensification%超临界流体技术与化工过程强化

    Institute of Scientific and Technical Information of China (English)

    张珺; 邵凡

    2011-01-01

    化工过程强化是通过减小设备体积、简化工艺或提高设备生产能力达到提高效率、减少废弃物的排放、降低成本、降低物耗等的目的.与传统方法相比,超临界流体技术作为一种新兴的技术提高了效率、简化了工艺、节约了材料、无二次污染,达到了过程强化的目的.介绍了超临界流体技术的优势,从而得到过程强化的效果.%Chemical process intensification can increase efficiency, reduce waste discharge, reduce cost and reduce material consumptions by reducing equipment volume, simplifying process and improving equipment production capacity. Compared with traditional method, supercritical fluid technology as a new technique can improve efficiency, simplify process, save materials and eliminate secondary pollution to reach the purpose of process intensification. In this paper, advantages of supercritical fluid technology was introduced, and effect of process intensification was discussed.

  15. Enhanced oral bioavailability of silymarin using liposomes containing a bile salt: preparation by supercritical fluid technology and evaluation in vitro and in vivo.

    Science.gov (United States)

    Yang, Gang; Zhao, Yaping; Zhang, Yongtai; Dang, Beilei; Liu, Ying; Feng, Nianping

    2015-01-01

    The aim of this investigation was to develop a procedure to improve the dissolution and bioavailability of silymarin (SM) by using bile salt-containing liposomes that were prepared by supercritical fluid technology (ie, solution-enhanced dispersion by supercritical fluids [SEDS]). The process for the preparation of SM-loaded liposomes containing a bile salt (SM-Lip-SEDS) was optimized using a central composite design of response surface methodology with the ratio of SM to phospholipids (w/w), flow rate of solution (mL/min), and pressure (MPa) as independent variables. Particle size, entrapment efficiency (EE), and drug loading (DL) were dependent variables for optimization of the process and formulation variables. The particle size, zeta potential, EE, and DL of the optimized SM-Lip-SEDS were 160.5 nm, -62.3 mV, 91.4%, and 4.73%, respectively. Two other methods to produce SM liposomes were compared to the SEDS method. The liposomes obtained by the SEDS method exhibited the highest EE and DL, smallest particle size, and best stability compared to liposomes produced by the thin-film dispersion and reversed-phase evaporation methods. Compared to the SM powder, SM-Lip-SEDS showed increased in vitro drug release. The in vivo AUC(0-t) of SM-Lip-SEDS was 4.8-fold higher than that of the SM powder. These results illustrate that liposomes containing a bile salt can be used to enhance the oral bioavailability of SM and that supercritical fluid technology is suitable for the preparation of liposomes.

  16. A finite element solution of the Reynolds equation of lubrication with film discontinuities: application to helical groove seals

    Science.gov (United States)

    Jarray, M.; Souchet, D.; Henry, Y.; Fatu, A.

    2017-02-01

    Helical groove seal, is one of the very few non-contact seals that have the capability to effectively seal a liquid. It finds use mainly in turbines and compressors. Although its reliability, this type of seals has not been investigated thoroughly because of its complex characteristics. This work presents a numerical analysis of a helical groove seal operating in laminar regime by means of solving the Reynolds equations for incompressible fluid film in steady state. Equations governing the fluid flow were solved by the finite element method. Although the simplifying assumptions of Reynolds model help to keep the computational time at an acceptable level, the inertia effects are neglected which may lead to unreliable results especially where the film thickness is discontinuous. The present approach, inspired by Arghir et al. [1] is able to take into account concentrated inertia effects, as described by a generalized Bernoulli equation. Comparisons made with the classical Reynolds model show that the film discontinuities should be taken into account when dealing with helically grooved seals. In addition, the leakage of fluid towards the air side was investigated for different parameters such as the groove angle and depth.

  17. Air riding seal for a turbine

    Energy Technology Data Exchange (ETDEWEB)

    Mills, Jacob A; Brown, Wesley D; Sexton, Thomas D; Jones, Russell B

    2016-07-19

    An air riding seal between a rotor and a stator in a turbine of a gas turbine engine, where an annular piston is movable in an axial direction within a housing that extends from the stator, and a bellows is secured to the annular piston to form a flexible air passageway from a compressed air inlet through the annular piston and into a cushion cavity that forms an air riding seal between the annular piston and the rotor sealing surface. In another embodiment, a flexible seal secured to and extending from the annular piston forms a sealing surface between the annular piston chamber and the annular piston to provide a seal and allow for axial movement.

  18. Coalbed methane reservoir boundaries and sealing mechanism

    Institute of Scientific and Technical Information of China (English)

    SU Xianbo; LIN Xiaoying; LIU Shaobo; SONG Yan

    2005-01-01

    It is important to investigate the coalbed methane reservoir boundaries for the classification, exploration, and development of the coalbed methane reservoir.Based on the investigation of the typical coalbed methane reservoirs in the world, the boundaries can be divided into four types: hydrodynamic boundary, air altered boundary,permeability boundary, and fault boundary. Hydrodynamic and air altered boundaries are ubiquitous boundaries for every coalbed methane reservoir. The four types of the fault sealing mechanism in the petroleum geological investigation (diagen- esis, clay smear, juxtaposition and cataclasis) are applied to the fault boundary of the coalbed methane reservoir. The sealing mechanism of the open fault boundary is the same with that of the hydrodynamic sealing boundary.The sealing mechanism of the permeability boundary is firstly classified into capillary pressure sealing and hydrocarbon concentration sealing. There are different controlling boundaries in coalbed methane reservoirs that are in different geological backgrounds. Therefore, the coalbed methane reservoir is diversiform.

  19. Balloon-Assisted Fistula Sealing Procedure for Symptomatic Tarlov Cysts.

    Science.gov (United States)

    Zheng, Xuesheng; Li, Shiting; Sheng, Hansong; Feng, Baohui; Zhang, Nu; Xie, Chaoran

    2016-04-01

    Tarlov cyst is an abnormal expansion of the spinal nerve sleeve, and it communicates with the subarachnoid cavity via a perineural fistula. This study presents our experience of a balloon-assisted fistula sealing procedure in treating Tarlov cyst. Twenty-two patients with symptomatic Tarlov cysts were surgically treated. An emulsion balloon was placed into the lumbar subarachnoid cistern through a trocar, so as to temporarily block cerebrospinal fluid flow, then the thecal sac was opened and the inlet of the fistula was sealed by suture of a muscular patch and reinforced by fibrin glue. Finally, the cyst wall was imbricated and the bony cavity was filled with pedicled muscle flaps. Comparing the preoperative and postoperative pain scores according to visual analog scale, 2 patients were slightly improved and 18 patients were substantially improved, including 3 completely pain-free cases. Only 2 patients were unchanged in pain, and both of them had multiple cysts. As a whole, the postoperative pain score was much better than the preoperative score (2.4 vs. 7.5; P cyst recurrence was found in 1 patient. The balloon-assisted fistula sealing procedure is safe and effective for Tarlov cyst, especially for the single cyst. It is a good complement to the cyst wall imbricating procedure. Copyright © 2016 Elsevier Inc. All rights reserved.

  20. Face seal assembly for rotating drum

    Science.gov (United States)

    Morgan, J. Giles; Rennich, Mark J.; Whatley, Marvin E.

    1982-01-01

    A seal assembly comprises a tube rotatable about its longitudinal axis and having two longitudinally spaced flanges projecting radially outwardly from the outer surface thereof. Slidably positioned against one of the flanges is a seal ring, and disposed between this seal ring and the other flange are two rings that are forced apart by springs, one of the latter rings being attached to a flexible wall.

  1. Refrigerating fluids; Fluides frigorigenes

    Energy Technology Data Exchange (ETDEWEB)

    Anon.

    1999-03-01

    Refrigerating fluids are experiencing a real revolution since few years. CFCs with their destructive effect on the ozone layer are now prohibited while HCFCs will be progressively eliminated and replaced by HFCs. However, HFCs can contribute to the increase of the greenhouse effect. The solutions proposed by thermal engineering professionals consist in the confinement of air-conditioning installations (elimination of recurrent leaks) and in the improvement of installations efficiency. HCFC fluids like the R 22 are still widely used in air-conditioning but they are supposed to be replaced by HFC fluids like the R 134a, the R 407C or the R 410A. This short paper gives a brief presentation of these fluids and of their chemical characteristics. (J.S.)

  2. Modeling the effect of seal leakage on spontaneous heating in a longwall gob area

    Energy Technology Data Exchange (ETDEWEB)

    Smith, A.C.; Yuan, L. [National Inst. for Occupational Safety and Health, Pittsburgh, PA (United States). Office of Mine Safety and Health Research

    2010-07-01

    Three coal mines in the United States with a history of spontaneous combustion use a bleederless ventilation system as a control measure. In a bleederless system, one of the headgate entries is used as the tailgate entry of the succeeding panel and is isolated from the gob of the active panel by gob seals that are installed in the headgate entry as the face advances. An active longwall panel using a Y-type bleederless ventilation system was simulated in this study. As longwall mining progresses, some seals are known to leak. Computational fluid dynamics (CFD) simulations were performed to study the effect of seal leakage on spontaneous heating of coal in the longwall gob area. The simulation results showed that under typical bleederless ventilation conditions, the maximum temperature in the gob increased with an increase in leakage rate. The maximum temperature occurred at the headgate side corner at the back end of the panel. When only 1 or 2 seals were leaking, the maximum temperature occurred around the seal. The results demonstrate that complex interactions between pressure differential and gob permeability at different locations in the gob cause ventilation pathways. The interactions depend greatly on gob permeability and seal leakage rates. 8 refs., 1 tab., 14 figs.

  3. Byzantine seals from the Ras fortress

    Directory of Open Access Journals (Sweden)

    Ivanišević Vujadin

    2013-01-01

    Full Text Available In this paper, seals found at the location of the Ras fortress (Tvrđava Ras have been published. Inscriptions on these seals show that they used to belong to persons which could be identified with certain military commanders who served under Alexios I Komnenos. The seals in question are: the seals of protonobelissimos Eustathios Kamytzes, Constantine Dalassenos Doukas, protoproedros and doux Constantine Kekaumenos and a certain person called Alexios. [Projekat Ministarstva nauke Republike Srbije, br. 177021 i br. 177032

  4. Ductile alloys for sealing modular component interfaces

    Energy Technology Data Exchange (ETDEWEB)

    Marra, John J.; Wessell, Brian J.; James, Allister W.; Marsh, Jan H.; Gear, Paul J.

    2017-08-08

    A vane assembly (10) having: an airfoil (12) and a shroud (14) held together without metallurgical bonding there between; a channel (22) disposed circumferentially about the airfoil (12), between the airfoil (12) and the shroud (14); and a seal (20) disposed in the channel (22), wherein during operation of a turbine engine having the vane assembly (10) the seal (20) has a sufficient ductility such that a force generated on the seal (20) resulting from relative movement of the airfoil (12) and the shroud (14) is sufficient to plastically deform the seal (20).

  5. A reliable sealing method for microbatteries

    Energy Technology Data Exchange (ETDEWEB)

    Wang, Yuxing; Cartmell, Samuel; Li, Qiuyan; Xiao, Jie; Li, Huidong; Deng, Zhiqun Daniel; Zhang, Ji-Guang

    2017-02-01

    With continuous downsizing of electronic devices, lithium batteries of traditional shapes cannot meet the demand where small-size high energy density batteries are needed. Conventional sealing methods become increasingly difficult to apply and impose high processing cost as the size of batteries decreases. In this report, a facile sealing method is proposed and demonstrated in CFx/Li mini-batteries. The method employs a temporary barrier to liquid electrolytes while relies on the epoxies/cell casings bond for the hermetic sealing. Cells sealed by this method show no degradation for an extended period of storage time.

  6. Sealing Occlusal Dentin Caries in Permanent Molars

    DEFF Research Database (Denmark)

    Qvist, Vibeke; Borum, Mette Kit; Møller, Kirsten Dynes

    2017-01-01

    /renewed and 20% were still functioning. No endodontics was performed. Kaplan–Meier and Cox regression survival analyses were performed on 341 sealings and 152 restorations in first and second molar teeth. The 7-y survival was 37% (CI, 29% to 45%) for sealings and 91% (CI, 85% to 96%) for restorations (P ....001). The median survival time for sealings not replaced by restorations was 7.3 y (CI, 6.4 y to NA). Survival of sealings was increased in patients with low caries risk and/or excellent oral hygiene, second molars compared with first molars, and lesions not extending the middle one-third of the dentin. Survival...

  7. Self-acting geometry for noncontact seals

    Science.gov (United States)

    Allen, G. P.

    1981-01-01

    Performance ot two self acting seal designs for a liquid oxygen (LOX) turbopump was predicted over ranges of pressure differential and speed. Predictions were compared with test results. Performance of a radial face seal for LOX was predicted up to 448 N/cu cm and 147 m/sec. Performance of a segmented circumferential seal for helium was predicted up to 69 N/cu cm and 189 m/sec. Results confirmed predictions of noncontact operation. Qualitative agreement between test and analysis was found. The LOX face seal evidently operated with mostly liquid in the self acting geometry and mostly gas across the dam.

  8. Ceramic/metal seals. [refractory materials for hermetic seals for lighium-metal sulfide batteries

    Science.gov (United States)

    Bredbenner, A. M.

    1977-01-01

    Design criteria are discussed for a hermetic seal capable of withstanding the 450 C operating temperature of a lithium-metal sulfide battery system. A mechanical seal consisting of two high strength alloy metal sleeves welded or brazed to a conductor assembly and pressed onto a ceramic is described. The conductor center passes through the ceramic but is not sealed to it. The seal is effected on the outside of the taper where the tubular part is pressed down over and makes contact.

  9. A comparison of the sealing ability of various temporary restorative materials to seal the access cavity: An in vitro study

    Directory of Open Access Journals (Sweden)

    Aji Markose

    2016-01-01

    Full Text Available Introduction: In multiple-appointment root canal treatment, a temporary filling material is used to seal the access cavity between visits. The primary function of this material is to prevent the contamination of the root canal system by fluids, organic debris, and bacteria from the oral cavity. Material and Methods: A total of fifty extracted noncarious unrestored human maxillaryanterior teeth with intact crowns and roots were selected The canals were instrumented using stepback technique and sodium hypochlorite (3% and hydrogen peroxide (3% were used as irrigants for each specimen alternatively. The coronal two-thirds of each canal were flared using Gates-Glidden drills up to no. 3 size and obturated with Gutta-percha using zinc oxide-eugenol (ZnOE as sealer. The teeth were then randomly selected and divided into six groups out of which four were experimental groups and two control groups. The teeth were then immersed in 2% methylene blue dye solution for 3 days. All sealing materials and Gutta-percha were gently removed from the walls of the canal, and the entire circumference of the canal wall examined for dye penetration. Results: The lowest mean leakage was in the Fermit-N group followed by Cavit-W, ZnOE, intermediate restorative materials (IRM, and positive control. Conclusion: Fermit-N showed better sealing ability compared to cavit, ZnOE and IRM.

  10. Sealed nickel-cadmium battery

    Energy Technology Data Exchange (ETDEWEB)

    1989-08-15

    Overcharge protection, and especially the chargeability of a sealed Ni/Cd battery with high currents is improved by rolling a carbon-containing powdered material into the surface of the negative electrode, which material catalyzes the reduction of oxygen. Wetting of the electrode with a Tylose dispersion prior to application of the powder (by powdering, vibration or in an agitator) improves the adhesion of the powder. The cadmium electrode thus prepared combines in itself the functions of a negative principal electrode and of an auxiliary oxygen electrode.

  11. Well sealing via thermite reactions

    Energy Technology Data Exchange (ETDEWEB)

    Lowry, William Edward; Dunn, Sandra Dalvit

    2016-11-15

    A platform is formed in a well below a target plug zone by lowering a thermite reaction charge into the well and igniting it, whereby the products of the reaction are allowed to cool and expand to form a platform or support in the well. A main thermite reaction charge is placed above the platform and ignited to form a main sealing plug for the well. In some embodiments an upper plug is formed by igniting an upper thermite reaction charge above the main thermite reaction charge. The upper plug confines the products of ignition of the main thermite reaction charge.

  12. Magnetohydrodynamic (MHD) channel corner seal

    Science.gov (United States)

    Spurrier, Francis R.

    1980-01-01

    A corner seal for an MHD duct includes a compressible portion which contacts the duct walls and an insulating portion which contacts the electrodes, sidewall bars and insulators. The compressible portion may be a pneumatic or hydraulic gasket or an open-cell foam rubber. The insulating portion is segmented into a plurality of pieces of the same thickness as the electrodes, insulators and sidewall bars and aligned therewith, the pieces aligned with the insulator being of a different size from the pieces aligned with the electrodes and sidewall bars to create a stepped configuration along the corners of the MHD channel.

  13. Magnet-Sleeve-Sealed Mini Trochoidal-Gear Pump Prototype with Polymer Composite Gear

    Directory of Open Access Journals (Sweden)

    Pedro Javier Gamez-Montero

    2017-09-01

    Full Text Available The trochoidal-gear technology has been growing in groundbreaking fields. Forthcoming applications are demanding to this technology a step forward in the conceiving stage of positive displacement machines. The compendium of the qualities and the inherent characteristics of trochoidal-gear technology, especially towards the gerotor pump, together with scale/size factor and magnetic-driven transmission has led to the idea of a magnet-sleeve-sealed variable flow mini trochoidal-gear pump. From its original concept, to the last phase of the design development, the proof of concept, this new product will intend to overcome problems such as noise, vibration, maintenance, materials, and dimensions. The paper aims to show the technological path followed from the concept, design, and model, to the manufacture of the first prototype, where the theoretical and numerical approaches are not always directly reflected in the prototype performance results. Early in the design process, from a standard-commercial sintered metal mini trochoidal-gear unit, fundamental characteristics and dimensional limitations have been evaluated becoming the strategic parameters that led to its configuration. The main technical challenge to confront is being sealed with non-exterior driveshaft, ensuring that the whole interior is filled and wetted with working fluid and helping the hydrodynamic film formation, the pumping effect, and the heat dissipation. Subsequently, the mini pump architecture, embodiment, methodology, materials, and manufacture are presented. The trend of applications of polymer composite materials and their benefits wanted to be examined with this new mini pump prototype, and a pure polyoxymethylene mini trochoidal-gear set has been designed and manufactured. Finally, both the sintered and the polymer trochoidal-gear units have been experimentally tested in an in-house full-instrumented mini test bench. Although the main goal of the presented work is the

  14. Seals at sea: modelling seal distribution in the German bight based on aerial survey data

    NARCIS (Netherlands)

    Herr, H.; Scheidat, M.; Lehnert, K.; Siebert, U.

    2009-01-01

    The Wadden Sea is an important habitat for harbour seals and grey seals. They regularly haul-out on sandbanks and islands along the coast. Comparably little is known about the time seals spend at sea and how they use the remainder of the North Sea. Yet, human activity in offshore waters is increasin

  15. Albinistic common seals (Phoca vitulina) and melanistic grey seals (Halichoerus grypus) rehabilitated in the Netherlands

    NARCIS (Netherlands)

    Osinga, Nynke; 't Hart, Pieter; Vader, Pieter C. van Voorst

    2010-01-01

    The Seal Rehabilitation and Research Centre (SRRC) in Pieterburen, The Netherlands, rehabilitates seals from the waters of the Wadden Sea, North Sea and Southwest Delta area. Incidental observations of albinism and melanism in common and grey seals are known from countries surrounding the North Sea.

  16. Bioprocess scale-up/down as integrative enabling technology: from fluid mechanics to systems biology and beyond.

    Science.gov (United States)

    Delvigne, Frank; Takors, Ralf; Mudde, Rob; van Gulik, Walter; Noorman, Henk

    2017-09-01

    Efficient optimization of microbial processes is a critical issue for achieving a number of sustainable development goals, considering the impact of microbial biotechnology in agrofood, environment, biopharmaceutical and chemical industries. Many of these applications require scale-up after proof of concept. However, the behaviour of microbial systems remains unpredictable (at least partially) when shifting from laboratory-scale to industrial conditions. The need for robust microbial systems is thus highly needed in this context, as well as a better understanding of the interactions between fluid mechanics and cell physiology. For that purpose, a full scale-up/down computational framework is already available. This framework links computational fluid dynamics (CFD), metabolic flux analysis and agent-based modelling (ABM) for a better understanding of the cell lifelines in a heterogeneous environment. Ultimately, this framework can be used for the design of scale-down simulators and/or metabolically engineered cells able to cope with environmental fluctuations typically found in large-scale bioreactors. However, this framework still needs some refinements, such as a better integration of gas-liquid flows in CFD, and taking into account intrinsic biological noise in ABM. © 2017 The Authors. Microbial Biotechnology published by John Wiley & Sons Ltd and Society for Applied Microbiology.

  17. Advanced high temperature fluid technology development using microgravity environment; Bisho juryoku kankyo riyo kodo koon ryutai gijutsu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-03-01

    Behavior of gas/liquid two-phase flow in tubes and behavior of air bubbles in liquid were investigated under the microgravity environment without convection by using the drop test facilities of the Japan Microgravity Center. To remove bubbles in the liquid under gravity, the strength of surface tension acting on the gas/liquid interface was made inhomogeneous. In this case, the moving velocity of bubbles on the gas/liquid interface was able to be raised up to the maximum of 2.4 mm/s. For the movement of bubbles in the horizontal direction under the condition of low relative velocity independent of the size of air bubbles in the duct, bubbles moving in the horizontal direction under 1g flowed almost linearly accompanying with the liquid flow. For the air bubble distribution in the bubble flow, where small bubbles flow in the vertical tubes, the fluid pattern of air bubble flow under 1g and {mu}g depended greatly on the initial condition of mixed bubbles. Fundamental data were obtained, as for the transportation and control of multicomponent bubbles, bubbles in the sound field, and bubbles in the liquid phase by magnetic force, and the fluid phenomena of bubbles in the subcool boiling region, a single bubble in the gradient electrical field, and bubbles in the tubes with small diameter. 47 refs., 97 figs., 8 tabs.

  18. Fluid mechanics for mechanical engineering. Technology and examples. 2. ed.; Stroemungslehre fuer den Maschinenbau. Technik und Beispiele

    Energy Technology Data Exchange (ETDEWEB)

    Siekmann, Helmut E.; Thamsen, Paul Uwe [Technische Univ. Berlin (Germany). Fluidsystemtechnik - Stroemungstechnik in Maschinen und Anlagen

    2009-07-01

    Detailed information on turbomachinery; Practical examples as learning aids; Compact presentation with good text and picture quality; Ideal for self-studies and for university teaching. This practically oriented information on the fundamentals of fluid mechanics addresses engineers and students of the engineering sciences, physics, and application-oriented mathematics. The many practical examples are useful for producers and users of the fluid mechanics industry. The text is structured in the same manner as in the 'Grundlagen' volume: Hydrostatics, kinematics, momentum law, Navier-Stokes equation of motion, potential flow, eddy flow, boundary layer flow, turbulent flow. The book closes with information on tube flow, flow around bodies, similarity laws, and numeric flow calculation. This the second, revised and edited edition. (orig.) [German] - Fuer gruendliche Kenntnisse von Stroemungsmaschinen - Praxisbeispiele als Lernhilfen - Kompakte Darstellung in hoher Text- und Bildqualitaet - Ideal zum Selbststudium und fuer die Vorlesung Diese anwendungsbezogene Vertiefung der Themen aus den Grundlagen der Stroemunglehre wendet sich an Ingenieure und Studenten der Ingenieurwissenschaften, Physik und anwendungsorientierten Mathematik. Die zahlreichen Praxisbeispiele sind hilfreich fuer Hersteller und Anwender aus vorwiegend stroemungstechnischer Industrie. Die Einteilung der Kapitel entspricht im Wesentlichen der im Band Grundlagen: Hydrostatik, Kinematik, Impulssatz, NAVIER-STOKES-Bewegungsgleichung, Potential-, Wirbel- und Grenzschichtstroemung sowie turbulente Stroemung. Das Buch schliesst mit Darstellungen ueber Rohrstroemungen, Umstroemung von Koerpern, Aehnlichkeitsgesetzen und numerische Stroemungsberechnung. Die 2. Auflage wurde aktualisiert und korrigiert. (orig.)

  19. Wellbore Seal Repair Using Nanocomposite Materials

    Energy Technology Data Exchange (ETDEWEB)

    Stormont, John [Univ. of New Mexico, Albuquerque, NM (United States)

    2016-08-31

    Nanocomposite wellbore repair materials have been developed, tested, and modeled through an integrated program of laboratory testing and numerical modeling. Numerous polymer-cement nanocomposites were synthesized as candidate wellbore repair materials using various combinations of base polymers and nanoparticles. Based on tests of bond strength to steel and cement, ductility, stability, flowability, and penetrability in opening of 50 microns and less, we identified Novolac epoxy reinforced with multi-walled carbon nanotubes and/or alumina nanoparticles to be a superior wellbore seal material compared to conventional microfine cements. A system was developed for testing damaged and repaired wellbore specimens comprised of a cement sheath cast on a steel casing. The system allows independent application of confining pressures and casing pressures while gas flow is measured through the specimens along the wellbore axis. Repair with the nanocomposite epoxy base material was successful in dramatically reducing the flow through flaws of various sizes and types, and restoring the specimen comparable to an intact condition. In contrast, repair of damaged specimens with microfine cement was less effective, and the repair degraded with application of stress. Post-test observations confirm the complete penetration and sealing of flaws using the nanocomposite epoxy base material. A number of modeling efforts have supported the material development and testing efforts. We have modeled the steel-repair material interface behavior in detail during slant shear tests, which we used to characterize bond strength of candidate repair materials. A numerical model of the laboratory testing of damaged wellbore specimens was developed. This investigation found that microannulus permeability can satisfactorily be described by a joint model. Finally, a wellbore model has been developed that can be used to evaluate the response of the wellbore system (casing, cement, and microannulus

  20. Numerical analysis of the non-contacting gas face seals

    Science.gov (United States)

    Blasiak, S.

    2017-08-01

    The non-contacting gas face seals are used in high-performance devices where the main requirements are safety and reliability. Compliance with these requirements is made possible by careful research and analysis of physical processes related to, inter alia, fluid flow through the radial gap and ring oscillations susceptible to being housed in the enclosure under the influence of rotor kinematic forces. Elaborating and developing mathematical models describing these phenomena allows for more and more accurate analysis results. The paper presents results of studies on stationary ring oscillations made of different types of materials. The presented results of the research allow to determine which of the materials used causes the greatest amplitude of the vibration of the system fluid film-working rings.

  1. Corkscrew Seals: Grey Seal (Halichoerus grypus) Infanticide and Cannibalism May Indicate the Cause of Spiral Lacerations in Seals

    Science.gov (United States)

    2016-01-01

    Large numbers of dead seals with characteristic spiral lesions have been washing ashore around the North Atlantic over the past two decades. Interactions with ship propellers and shark predation have been suggested as the likely causal mechanisms. However, new evidence points towards a more likely candidate: grey seal predation. An adult male grey seal was observed and recorded catching, killing and eating five weaned grey seal pups over a period of one week on the Isle of May, Scotland. A further 9 carcasses found in the same area exhibited similar injuries. Post mortem analysis of lesions indicated the wound characteristics were similar to each other and in 12 of the 14 carcasses analysed, were indistinguishable from carcasses previously attributed to propeller interaction. We therefore propose that most of the seal carcasses displaying spiral lacerations in the UK are caused by grey seal predation. Cases in other locations should be re-evaluated using the scoring system presented here to identify whether grey seal predation is a major cause of mortality in phocid seals. PMID:27254025

  2. Corkscrew Seals: Grey Seal (Halichoerus grypus Infanticide and Cannibalism May Indicate the Cause of Spiral Lacerations in Seals.

    Directory of Open Access Journals (Sweden)

    Andrew Brownlow

    Full Text Available Large numbers of dead seals with characteristic spiral lesions have been washing ashore around the North Atlantic over the past two decades. Interactions with ship propellers and shark predation have been suggested as the likely causal mechanisms. However, new evidence points towards a more likely candidate: grey seal predation. An adult male grey seal was observed and recorded catching, killing and eating five weaned grey seal pups over a period of one week on the Isle of May, Scotland. A further 9 carcasses found in the same area exhibited similar injuries. Post mortem analysis of lesions indicated the wound characteristics were similar to each other and in 12 of the 14 carcasses analysed, were indistinguishable from carcasses previously attributed to propeller interaction. We therefore propose that most of the seal carcasses displaying spiral lacerations in the UK are caused by grey seal predation. Cases in other locations should be re-evaluated using the scoring system presented here to identify whether grey seal predation is a major cause of mortality in phocid seals.

  3. Corkscrew Seals: Grey Seal (Halichoerus grypus) Infanticide and Cannibalism May Indicate the Cause of Spiral Lacerations in Seals.

    Science.gov (United States)

    Brownlow, Andrew; Onoufriou, Joseph; Bishop, Amanda; Davison, Nicholas; Thompson, Dave

    2016-01-01

    Large numbers of dead seals with characteristic spiral lesions have been washing ashore around the North Atlantic over the past two decades. Interactions with ship propellers and shark predation have been suggested as the likely causal mechanisms. However, new evidence points towards a more likely candidate: grey seal predation. An adult male grey seal was observed and recorded catching, killing and eating five weaned grey seal pups over a period of one week on the Isle of May, Scotland. A further 9 carcasses found in the same area exhibited similar injuries. Post mortem analysis of lesions indicated the wound characteristics were similar to each other and in 12 of the 14 carcasses analysed, were indistinguishable from carcasses previously attributed to propeller interaction. We therefore propose that most of the seal carcasses displaying spiral lacerations in the UK are caused by grey seal predation. Cases in other locations should be re-evaluated using the scoring system presented here to identify whether grey seal predation is a major cause of mortality in phocid seals.

  4. Calcite sealing in a fractured geothermal reservoir: Insights from combined EBSD and chemistry mapping

    Science.gov (United States)

    McNamara, David D.; Lister, Aaron; Prior, Dave J.

    2016-09-01

    Fractures play an important role as fluid flow pathways in geothermal resources hosted in indurated greywacke basement of the Taupo Volcanic Zone, New Zealand, including the Kawerau Geothermal Field. Over time, the permeability of such geothermal reservoirs can be degraded by fracture sealing as minerals deposit out of transported geothermal fluids. Calcite is one such fracture sealing mineral. This study, for the first time, utilises combined data from electron backscatter diffraction and chemical mapping to characterise calcite vein fill morphologies, and gain insight into the mechanisms of calcite fracture sealing in the Kawerau Geothermal Field. Two calcite sealing mechanisms are identified 1) asymmetrical syntaxial growth of calcite, inferred by the presence of single, twinned, calcite crystals spanning the entire fracture width, and 2) 3D, interlocking growth of bladed vein calcite into free space as determined from chemical and crystallographic orientation mapping. This study also identifies other potential uses of combined EBSD and chemical mapping to understand geothermal field evolution including, potentially informing on levels of fluid supersaturation from the study of calcite lattice distortion, and providing information on a reservoir's history of stress, strain, and deformation through investigation of calcite crystal deformation and twinning patterns.

  5. A device for vacuum drying, inert gas backfilling and solder sealing of hermetic implant packages.

    Science.gov (United States)

    Schuettler, Martin; Huegle, Matthias; Ordonez, Juan S; Wilde, Juergen; Stieglitz, Thomas

    2010-01-01

    Modern implanted devices utilize microelectronics that have to be protected from the body fluids in order to maintain their functionality over decades. Moisture protection of implants is addressed by enclosing the electronic circuits into gas-tight packages. In this paper we describe a device that allows custom-built hermetic implant packages to be vacuum-dried (removing residual moisture from inside the package), backfilled with an inert gas at adjustable pressure and hermetically sealed employing a solder seal. A typical operation procedure of the device is presented.

  6. A strategy to seal exploratory boreholes in unsaturated tuff; Yucca Mountain Site Characterization Project

    Energy Technology Data Exchange (ETDEWEB)

    Fernandez, J.A. [Sandia National Labs., Albuquerque, NM (United States); Case, J.B.; Givens, C.A.; Carney, B.C. [IT Corp., Albuquerque, NM (United States)

    1994-04-01

    This report presents a strategy for sealing exploratory boreholes associated with the Yucca Mountain Site Characterization Project. Over 500 existing and proposed boreholes have been considered in the development of this strategy, ranging from shallow (penetrating into alluvium only) to deep (penetrating into the groundwater table). Among the comprehensive list of recommendations are the following: Those boreholes within the potential repository boundary and penetrating through the potential repository horizon are the most significant boreholes from a performance standpoint and should be sealed. Shallow boreholes are comparatively insignificant and require only nominal sealing. The primary areas in which to place seals are away from high-temperature zones at a distance from the potential repository horizon in the Paintbrush nonwelded tuff and the upper portion of the Topopah Spring Member and in the tuffaceous beds of the Calico Hills Unit. Seals should be placed prior to waste emplacement. Performance goals for borehole seals both above and below the potential repository are proposed. Detailed construction information on the boreholes that could be used for future design specifications is provided along with a description of the environmental setting, i.e., the geology, hydrology, and the in situ and thermal stress states. A borehole classification scheme based on the condition of the borehole wall in different tuffaceous units is also proposed. In addition, calculations are presented to assess the significance of the boreholes acting as preferential pathways for the release of radionuclides. Design calculations are presented to answer the concerns of when, where, and how to seal. As part of the strategy development, available technologies to seal exploratory boreholes (including casing removal, borehole wall reconditioning, and seal emplacement) are reviewed.

  7. Stirling engine with air working fluid

    Science.gov (United States)

    Corey, John A.

    1985-01-01

    A Stirling engine capable of utilizing air as a working fluid which includes a compact heat exchange module which includes heating tube units, regenerator and cooler positioned about the combustion chamber. This arrangement has the purpose and effect of allowing the construction of an efficient, high-speed, high power-density engine without the use of difficult to seal light gases as working fluids.

  8. Pressure drop and cavitation investigations on static helical-grooved square, triangular and curved cavity liquid labyrinth seals

    Energy Technology Data Exchange (ETDEWEB)

    Asok, S.P., E-mail: asoksp@yahoo.co [Department of Mechanical Engineering, Mepco Schlenk Engineering College (MSEC), Sivakasi, Tamilnadu 626005 (India); Sankaranarayanasamy, K. [National Institute of Technology, Trichy (India); Sundararajan, T. [Indian Institute of Technology Madras, Chennai (India); Vaidyanathan, G. [Fast Reactor Technology Group, Indira Gandhi Centre for Atomic Research (IGCAR), Kalpakkam (India); Kumar, K. Udhaya [Department of Mechanical Engineering, MSEC, Sivakasi (India)

    2011-03-15

    Research highlights: Design and testing of newer and novel helical-grooved profiles of labyrinths capable of ensuring high pressure drops even at low liquid flow rates. Implementation of genetic algorithm in the optimization of labyrinth seal through surrogate modelling means. Application of CFD in three-dimensional fluid flow and cavitation analysis for static helical grooved labyrinth seals. - Abstract: Sodium cooled Fast Breeder Reactors (FBR) form the second stage of India's Nuclear power programme. Through a narrow annular space in the grid plate assembly of a prototype FBR, a very low leakage flow of liquid metal sodium should pass, experiencing a stipulated high pressure drop, and without much cavitation. To achieve this, a suitable labyrinth seal is required to be developed for use in the annulus. Water is employed as the model testing liquid which is estimated to experience a pressure drop ratio of 10.5 at the rated leakage flow. Previously studied circular or sinusoidal-grooved square, triangular or curved cavity labyrinth seals were unable to meet this value. In the present work, Computational Fluid Dynamics (CFD) analyses are carried out on Helical-grooved Square cavity Labyrinth Seals (HSLS), using commercial code Fluent. It is found that the geometrical configuration of the grooves plays a major role on the pressure drop. Experimental results reveal close agreement with CFD predictions. An optimal configuration of this square cavity seal is identified by applying genetic algorithm (GA) using commercial packages. It meets just about 24% of the targeted value. Later, using parametric CFD analyses, a Helical-grooved Triangular cavity Labyrinth Seal (HTLS) and different Helical-grooved Curved cavity Labyrinth Seals (HCLS) are analysed. The most favourable profile is tested and found to reach the required pressure drop. CFD cavitation analyses predict the intensity of cavitation in these seals to be below prohibitive levels.

  9. Supercritical fluid chromatography and steady-state recycling: phase appropriate technologies for the resolutions of pharmaceutical intermediates in the early drug development stage.

    Science.gov (United States)

    Yan, Tony Q; Orihuela, Carlos; Preston, Jay P; Xia, Fang

    2010-11-01

    The use of phase appropriate technologies is critical for efficiently moving drug candidates forward in the early stages of drug discovery and development. Phase appropriate purification technology develops the analytical method and subsequently scales up the method and turns the sample around quickly (Kennedy et al., J Chromatogr A 2004; 1046:55). In this article, separation results and conditions from supercritical fluid chromatography (SFC), high-performance liquid chromatography (HPLC), and steady-state recycling (SSR) for the resolutions of three pharmaceutical intermediates in the early stage of the drug development are discussed. The first study used SFC and SSR to separate an impurity for a Good Manufacturing Practice (GMP) campaign. The analytical method development and scale-up conditions are discussed. Productivity, solvent usage, and sample solubility under SFC and SSR conditions are also compared. The second study compared SFC to batch HPLC in separating a diastereomer. Due to higher separation efficiency, SFC was able to resolute multiple peaks. The third study involved the addition of dichloromethane as a co-solvent in SFC purification--improving sample selectivity and solubility. From the separation results of these purifications, SFC and SSR are clearly phase appropriate technologies in the early drug development stage.

  10. Cold welding sealing of copper-water micro heat pipe ends

    Institute of Scientific and Technical Information of China (English)

    TANG Yong; LU Long-sheng; DENG Da-xiang; YUAN Dong

    2009-01-01

    The quality of micro heat pipe(MHP) is strongly affected by sealing technology. Based on the analysis of requirements of sealing technology, a cold welding technology was presented to seal MHP. In the cold welding process, compression force was used to flatten micro groove copper(MGC) tube. Then the bonding of MGC tube was reached because of intensively plastic deformation of MGC tube under pressure. It is found that the plastic deformation area of the cold welding of MGC tube can be divided into three sections. The deformation of micro grooves in each section was investigated; the influence of the dimensions of cylindrical heads on the weld joint shape and strength was studied; and a comparison between smooth copper tube and MGC tube was done. The results show that a groove compression stage exists in the cold welding of MGC tube besides a flattened stage and a melting stage.

  11. Innovative Self-Healing Seals for Solid Oxide Fuel Cells (SOFC)

    Energy Technology Data Exchange (ETDEWEB)

    Raj Singh

    2012-06-30

    Solid oxide fuel cell (SOFC) technology is critical to several national initiatives. Solid State Energy Conversion Alliance (SECA) addresses the technology needs through its comprehensive programs on SOFC. A reliable and cost-effective seal that works at high temperatures is essential to the long-term performance of the SOFC for 40,000 hours at 800°C. Consequently, seals remain an area of highest priority for the SECA program and its industry teams. An innovative concept based on self-healing glasses was advanced and successfully demonstrated through seal tests for 3000 hours and 300 thermal cycles to minimize internal stresses under both steady state and thermal transients for making reliable seals for the SECA program. The self-healing concept requires glasses with low viscosity at the SOFC operating temperature of 800°C but this requirement may lead to excessive flow of the glass in areas forming the seal. To address this challenge, a modification to glass properties by addition of particulate fillers is pursued in the project. The underlying idea is that a non-reactive ceramic particulate filler is expected to form glass-ceramic composite and increase the seal viscosity thereby increasing the creep resistance of the glass-composite seals under load. The objectives of the program are to select appropriate filler materials for making glass-composite, fabricate glass-composites, measure thermal expansion behaviors, and determine stability of the glass-composites in air and fuel environments of a SOFC. Self-healing glass-YSZ composites are further developed and tested over a longer time periods under conditions typical of the SOFCs to validate the long-term stability up to 2000 hours. The new concepts of glass-composite seals, developed and nurtured in this program, are expected to be cost-effective as these are based on conventional processing approaches and use of the inexpensive materials.

  12. Beta testing of MTI seal codes

    Science.gov (United States)

    Scharrer, Joseph

    1994-01-01

    An evaluation of MTI seal codes is made by comparing cylindrical air and water seals. Results are presented in viewgraph format and show that: ICYL and GCYL geometry variations are desirable; load and direct stiffness calculations are good; damping and cross-coupled stiffness predictions are poor; added mass coefficients should be calculated; and variation in inlet tangential velocity is critical to design.

  13. Earlier pupping in harbour seals, Phoca vitulina

    NARCIS (Netherlands)

    Reijnders, P.J.H.; Brasseur, S.M.J.M.; Meesters, H.W.G.

    2010-01-01

    The annual reproductive cycle of most seal species is characterized by a tight synchrony of births. Typically, timing of birth shows little inter-annual variation. Here, however we show that harbour seals Phoca vitulina from the Wadden Sea (southeast North Sea) have shortened their yearly cycle, mov

  14. 19 CFR 101.7 - Customs seal.

    Science.gov (United States)

    2010-04-01

    ... 19 Customs Duties 1 2010-04-01 2010-04-01 false Customs seal. 101.7 Section 101.7 Customs Duties U.S. CUSTOMS AND BORDER PROTECTION, DEPARTMENT OF HOMELAND SECURITY; DEPARTMENT OF THE TREASURY GENERAL PROVISIONS § 101.7 Customs seal. (a) Design. According to the design furnished by the...

  15. Space Environment Effects on Silicone Seal Materials

    Science.gov (United States)

    deGroh, Henry C., III; Daniels, Christopher C.; Dever, Joyce A.; Miller, Sharon K.; Waters, Deborah L.; Finkbeiner, Joshua R.; Dunlap, Patrick H.; Steinetz, Bruce M.

    2010-01-01

    A docking system is being developed by the NASA to support future space missions. It is expected to use redundant elastomer seals to help contain cabin air during dockings between two spacecraft. The sealing surfaces are exposed to the space environment when vehicles are not docked. In space, the seals will be exposed to temperatures between 125 to -75 C, vacuum, atomic oxygen, particle and ultraviolet radiation, and micrometeoroid and orbital debris (MMOD). Silicone rubber is the only class of space flight-qualified elastomeric seal material that functions across the expected temperature range. NASA Glenn has tested three silicone elastomers for such seal applications: two provided by Parker (S0899-50 and S0383-70) and one from Esterline (ELA-SA-401). The effects of atomic oxygen (AO), UV and electron particle radiation, and vacuum on the properties of these three elastomers were examined. Critical seal properties such as leakage, adhesion, and compression set were measured before and after simulated space exposures. The S0899-50 silicone was determined to be inadequate for extended space seal applications due to high adhesion and intolerance to UV, but both S0383-70 and ELA-SA-401 seals were adequate.

  16. Space Environment's Effects on Seal Materials

    Science.gov (United States)

    deGroh, Henry C., III; Daniels, Christopher C.; Dunlap, Patrick; Miller, Sharon; Dever, Joyce; Waters, Deborah; Steinetz, Bruce M.

    2007-01-01

    A Low Impact Docking System (LIDS) is being developed by the NASA Johnson Space Center to support future missions of the Crew Exploration Vehicle (CEV). The LIDS is androgynous, such that each system half is identical, thus any two vehicles or modules with LIDS can be coupled. Since each system half is a replica, the main interface seals must seal against each other instead of a conventional flat metal surface. These sealing surfaces are also expected to be exposed to the space environment when vehicles are not docked. The NASA Glenn Research Center (NASA GRC) is supporting this project by developing the main interface seals for the LIDS and determining the durability of candidate seal materials in the space environment. In space, the seals will be exposed to temperatures of between 50 to 50 C, vacuum, atomic oxygen, particle and ultraviolet radiation, and micrometeoroid and orbital debris (MMOD). NASA GRC is presently engaged in determining the effects of these environments on our candidate elastomers. Since silicone rubber is the only class of seal elastomer that functions across the expected temperature range, NASA GRC is focusing on three silicone elastomers: two provided by Parker Hannifin (S0-899-50 and S0-383-70) and one from Esterline Kirkhill (ELA-SA-401). Our results from compression set, elastomer to elastomer adhesion, and seal leakage tests before and after various simulated space exposures will be presented.

  17. Development of Design Technology on Thermal-Hydraulic Performance in Tight-Lattice Rod Bundles: III - Numerical Evaluation of Fluid Mixing Phenomena using Advanced Interface-Tracking Method -

    Science.gov (United States)

    Yoshida, Hiroyuki; Nagayoshi, Takuji; Takase, Kazuyuki; Akimoto, Hajime

    Thermal-hydraulic design of the current boiling water reactor (BWR) is performed by correlations with empirical results of actual-size tests. However, for the Innovative Water Reactor for Flexible Fuel Cycle (FLWR) core, an actual size test of an embodiment of its design is required to confirm or modify such correlations. Development of a method that enables the thermal-hydraulic design of nuclear reactors without these actual size tests is desired, because these tests take a long time and entail great cost. For this reason we developed an advanced thermal-hydraulic design method for FLWRs using innovative two-phase flow simulation technology. In this study, detailed Two-Phase Flow simulation code using advanced Interface Tracking method: TPFIT is developed to calculate the detailed information of the two-phase flow. We tried to verify the TPFIT code by comparing it with the 2-channel air-water and steam-water mixing experimental results. The predicted result agrees well the observed results and bubble dynamics through the gap and cross flow behavior could be effectively predicted by the TPFIT code, and pressure difference between fluid channels is responsible for the fluid mixing.

  18. Active Infrared Thermography for Seal Contamination Detection in Heat-Sealed Food Packaging

    Directory of Open Access Journals (Sweden)

    Karlien D’huys

    2016-11-01

    Full Text Available Packaging protects food products from environmental influences, assuring quality and safety throughout shelf life if properly performed. Packaging quality depends on the quality of the packaging material and of the closure or seal. A common problem possibly jeopardizing seal quality is the presence of seal contamination, which can cause a decreased seal strength, an increased packaging failure risk and leak formation. Therefore, early detection and removal of seal contaminated packages from the production chain is crucial. In this work, a pulsed-type active thermography method using the heated seal bars as an excitation source was studied for detecting seal contamination. Thermal image sequences of contaminated seals were recorded shortly after sealing. The detection performances of six thermal image processing methods, based on a single frame, a fit of the cooling profiles, thermal signal reconstruction, pulsed phase thermography, principal component thermography and a matched filter, were compared. High resolution digital images served as a reference to quantify seal contamination, and processed thermal images were mapped to these references. The lowest detection limit (equivalent diameter 0.60 mm was obtained for the method based on a fit of the cooling profiles. Moreover, the detection performance of this method did not depend strongly on the time after sealing at which recording of the thermal images was started, making it a robust and generally applicable method.

  19. Grey seal (Halichoerus grypus) predation on harbour seals (Phoca vitulina) on the island of Helgoland, Germany

    Science.gov (United States)

    van Neer, Abbo; Jensen, Lasse Fast; Siebert, Ursula

    2015-03-01

    The prey spectrum of grey seals has to date been described as largely consisting of different fish, cephalopod and shrimp species. On the German island of Helgoland Düne, where harbour seals (Phoca vitulina) and grey seals (Halichoerus grypus) co-occur, a young male grey seal was observed in 2013 and again in 2014 preying upon young harbour seals. A harbour seal carcass with severe traumatic lesions was retrieved and post-mortem examinations were performed. In the following weeks several carcasses showing similar lesions were found. Sightings of grey seals assumed to be preying on harbour porpoises have increased around the North Sea. Increased competition as well as individualised behaviour could explain the increased number of observations, but former cases of abnormal lesions of marine mammals attributed to for example predation by sharks or mechanical processes should be revisited with regard to the emerging knowledge.

  20. [Methods for sealing of corneal perforations].

    Science.gov (United States)

    Samoilă, O; Totu, Lăcrămioara; Călugăru, M

    2012-01-01

    A variety of corneal pathology can lead to corneal ulcers and perforations. A deep corneal ulcer may need surgical treatment to allow good volume restoration and reepithelisation. Corneal perforation must be sealed and when the perforation is large, the task of repairing the defect can be underwhelming. The elegant solution is the corneal transplant, but this is not always readily available, especially in undeveloped countries. We present here two cases with different solutions to seal the perforated cornea: the first one has a large peripheral defect and it is successfully sealed with scleral patch and the second one is central with small perforation and is successfully sealed with multilayered amniotic membrane. Both cases are followed for over 12 months and demonstrate good corneal restoration (both on clinical examination and corneal topography). Sclera and amniotic membrane can be used to seal corneal defects when corneal transplant is not readily available.

  1. Film riding seal assembly for turbomachinery

    Energy Technology Data Exchange (ETDEWEB)

    Bidkar, Rahul Anil; Giametta, Andrew Paul; Gibson, Nathan Evan McCurdy; Cleveland, Nicolas Joseph

    2016-06-07

    An aerodynamic seal assembly for a rotary machine includes multiple sealing segments disposed circumferentially intermediate to a stationary housing and a rotor. Each of the segments includes a shoe plate with a forward load-bearing section and an aft load-bearing section configured to generate an aerodynamic force between the shoe plate and the rotor. The shoe plate includes at least one labyrinth teeth facing the rotor and positioned between the forward load-bearing section and the aft load-bearing section. The sealing segment also includes at least one spring connected to a pedestal located about midway of an axial length of the shoe plate and to a stator interface element. Further, the sealing segment includes a rigid segmented secondary seal attached to the stator interface element at one first end and in contact with the pedestal of the shoe plate at one second end.

  2. A reliable sealing method for microbatteries

    Science.gov (United States)

    Wang, Yuxing; Cartmell, Samuel; Li, Qiuyan; Xiao, Jie; Li, Huidong; Deng, Zhiqun Daniel; Zhang, Ji-Guang

    2017-02-01

    As electronic devices continue to become smaller, their energy sources (i.e., batteries) also need to be smaller. Typically, energy densities of batteries decrease as the battery size decreases due to the relative increase of parasitic weight such as packaging materials. In addition, the sealing methods in conventional batteries are difficult to apply to microbatteries. In this work, we developed a facile sealing method for microbatteries. The method employs a dual-sealing concept: a first rubber barrier temporally confines the organic electrolytes and a second adhesive barrier forms a hermetic seal with the battery case. With this innovative sealing approach, excellent shelf life and operation life of the batteries have been demonstrated. A minimal amount of packing materials is employed resulting in high energy densities.

  3. 废弃钻井液无害化处理技术的研究%Research of waste drilling fluid disposal technology

    Institute of Scientific and Technical Information of China (English)

    何长明; 李俊华; 王佳

    2016-01-01

    The major ingredient of mud was polyacrylamide , sodium carboxymethyl cellulose , sulfonated asphalt ,no fluorescence lubricants and so on .It has the high viscosity ,high concentration of organic matter and pollutant characteristics .It may quickly solve the stability of the mud system by chemical treatment technology.The results show that polyacrylamide degrading HK 618, demulsifier HK201 and catalyst HK458 could make waste drilling fluid rapid degradation hydration for 2 h.It achieve the complete sepa-ration of solid phase ,water and oil .Adopting the new technology can solve the stability problem of drilling fluid viscous material .It has the vital significance for the future ecological restoration .%延长油田应用的泥浆主要成分为聚丙烯酰胺、羧甲基纤维素钠等,具有粘度高、有机物浓度高、污染物种类多等特点,加入研制的聚丙烯酰胺降解剂HK618、破乳剂HK201和催化剂HK458,可以使其2 h内快速降解水化成小分子,实现固相、水、油的完全分离。采用新技术能够解决传统化学处理中钻井液废弃物粘稠物质的稳定性问题,对未来生态恢复也具有重要的意义。

  4. Amniotic fluid

    Science.gov (United States)

    ... carefully. Removing a sample of the fluid through amniocentesis can provide information about the sex, health, and development of the fetus. Images Amniocentesis Amniotic fluid Polyhydramnios Amniotic fluid References Cunningham FG, ...

  5. Radiation Safety of Sealed Radioactive Sources

    Energy Technology Data Exchange (ETDEWEB)

    Pryor, Kathryn H.

    2015-01-01

    Sealed radioactive sources are used in a wide variety of occupational settings and under differing regulatory/licensing structures. The definition of a sealed radioactive source varies between US regulatory authorities and standard-setting organizations. Potential problems with sealed sources cover a range of risks and impacts. The loss of control of high activity sealed sources can result in very high or even fatal doses to members of the public who come in contact with them. Sources that are not adequately sealed, and that fail, can cause spread of contamination and potential intake of radioactive material. There is also the possibility that sealed sources may be (or threatened to be) used for terrorist purposes and disruptive opportunities. Until fairly recently, generally-licensed sealed sources and devices received little, if any, regulatory oversight, and were often forgotten, lost or unaccounted for. Nonetheless, generally licensed devices can contain fairly significant quantities of radioactive material and there is some potential for exposure if a device is treated in a way that it was never designed. Industrial radiographers use and handle high activity and/or high-dose rate sealed sources in the field with a high degree of independence and minimal regulatory oversight. Failure to follow operational procedures and properly handle radiography sources can and has resulted in serious injuries and death. Industrial radiographers have experienced a disproportionately large fraction of incidents that result in unintended exposure to radiation. Sources do not have to contain significant quantities of radioactive material to cause problems in the event of their failure. A loss of integrity can cause the spread of contamination and potential exposure to workers and members of the public. The NCRP has previously provided recommendations on select aspects of sealed source programs. Future efforts to provide recommendations for sealed source programs are discussed.

  6. Does the seal licensing system in Scotland have a negative impact on seal welfare?

    Directory of Open Access Journals (Sweden)

    Laetitia Nunny

    2016-08-01

    Full Text Available This study examined the licensing system that permits seal shooting in Scotland, which was established under Part 6 Conservation of Seals of the Marine (Scotland Act 2010. Four approaches were used: data were collated and analyzed from both the Scottish Government and Scottish Marine Animal Stranding Scheme; a survey was sent to current license holders and informal interviews were conducted with key stakeholder types. Between February 2011 and the end of October 2015, 1229 gray seals and 275 common seals were reported shot under license to the Scottish Government. The numbers of seals reported as shot has reduced year-on-year since the licensing system was put in place. While some license holders, notably fish farms, were using some non-lethal forms of deterrent to reduce seal-related damage, these were often used alongside seal shooting. Of the seals reported as shot to the Scottish Government, only a small percentage were also reported to the Scottish Marine Animal Stranding Scheme, despite this being a licensing requirement. Only 2.3% of the shot gray seals and 4.5% of the shot common seals were necropsied. There is evidence from these necropsies that some seals had not died instantly or had not been shot in the manner recommended by the Scottish Seal Management Code of Practice. These preliminary results show that more carcasses need to be recovered and necropsied if the welfare implications of current seal shooting practice are to be properly assessed. The current legislation does not specify closed seasons to protect breeding seals and thirty-five per cent of necropsied seals were pregnant gray seals. Seals have also been shot during their lactation periods when pups are dependent on their mothers. This raises significant welfare concerns. The re-introduction of closed seasons specific to each species of seal is recommended along with greater effort to deploy non-lethal methods. Independent assessment of the number of seals being killed

  7. Preparation and characterization of a stereocomplex of poly(lactide-co-ε-caprolactone/tricalcium phosphate biocomposite using supercritical fluid technology

    Directory of Open Access Journals (Sweden)

    P. Purnama

    2013-12-01

    Full Text Available A novel biocomposite material from a stereocomplex of poly (L-lactide-co-ε-caprolactone (PLLCL and poly (D-lactide-co-ε-caprolactone (PDLCL and inorganic tricalcium phosphate (TCP was prepared by supercritical fluid method. Both pristine and poly (L-lactide-grafted-TCP (PLLA-g-TCP were used. PLLA-g-TCP was produced by ringopening polymerization of L-lactide in the presence of surface-activated TCP. Infrared (IR spectroscopy and scanning electron microscopic (SEM images confirm the attachment of PLLA onto the activated TCP surface. The stereocomplex formation of biocomposite was confirmed by differential scanning calorimetry (DSC and wide-angle X-ray diffraction (WAXD. The biocomposite containing PLLA-g-TCP has higher stereocomplex degree and more homogeneous TCP distribution compared to the biocomposite containing pristine TCP. The presence of PLLA-g-TCP in the stereocomplex PLLCLPDLCL (s-PDLCL enhance the stereocomplex degree up to a certain content and also supports the homogeneous TCP dispersion in the stereocomplex matrix. These phenomena support the improvement in mechanical properties of the s-PDLCL composite the optimum content of PLLA-g-TCP being 10%. The biocomposites containing TCP materials are promising materials for biomedical application, especially for bone tissue engineering.

  8. Ocean climate and seal condition

    Directory of Open Access Journals (Sweden)

    Crocker Daniel E

    2005-03-01

    Full Text Available Abstract Background The condition of many marine mammals varies with fluctuations in productivity and food supply in the ocean basin where they forage. Prey is impacted by physical environmental variables such as cyclic warming trends. The weaning weight of northern elephant seal pups, Mirounga angustirostris, being closely linked to maternal condition, indirectly reflects prey availability and foraging success of pregnant females in deep waters of the northeastern Pacific. The aim of this study was to examine the effect of ocean climate on foraging success in this deep-diving marine mammal over the course of three decades, using cohort weaning weight as the principal metric of successful resource accrual. Results The mean annual weaning weight of pups declined from 1975 to the late 1990s, a period characterized by a large-scale, basin-wide warm decadal regime that included multiple strong or long-duration El Niños; and increased with a return to a cool decadal regime from about 1999 to 2004. Increased foraging effort and decreased mass gain of adult females, indicative of reduced foraging success and nutritional stress, were associated with high ocean temperatures. Conclusion Despite ranging widely and foraging deeply in cold waters beyond coastal thermoclines in the northeastern Pacific, elephant seals are impacted significantly by ocean thermal dynamics. Ocean warming redistributes prey decreasing foraging success of females, which in turn leads to lower weaning mass of pups. Annual fluctuations in weaning mass, in turn, reflect the foraging success of females during the year prior to giving birth and signals changes in ocean temperature cycles.

  9. The sealing of excavation damaged zones in salt formations using sodium silicate solutions

    Energy Technology Data Exchange (ETDEWEB)

    Engelhardt, Hans-Joachim; Schmidt, Holger; Borstel, Lieselotte von [DBE TECHNOLOGY GmbH, Peine (Germany). Dept. of Repository Safety

    2015-07-01

    Since many decades, pressure grouting is an effective technique of civil engineering for sealing and stabilization purposes. Due to the potential contamination of fluids, grouting is of particular importance in repositories of radioactive waste. Traditional grouts for the sealing of fine fractures are sodium silicate solutions. Laboratory and field investigations prove that the particle-free solutions can be used to permanently seal excavation damaged zones (EDZ) in salt formations, because the solid reaction products are inert or almost insoluble. EDZ permeabilities of 10{sup -17} m{sup 2} can be achieved and were determined on the basis of the injection pressures and flow rates. High grouting pressures were realized as local test loadings. Laboratory tests show the fixation of Co{sup 2+}, Ni{sup 2+}, Sr{sup 2+}, Ba{sup 2+}, [UO{sub 2}]{sup 2+} and illustrate that sodium silicates may act additionally as a chemical barrier.

  10. Performance characteristics of a self-sealing/self-healing barrier

    Energy Technology Data Exchange (ETDEWEB)

    McGregor, R.G. [Water Technology International Corp., Burlington, Ontario (Canada)]|[Canadian Clean Technology Centre, Burlington, Ontario (Canada); Stegemann, J.A. [Canadian Clean Technology Centre, Burlington, Ontario (Canada)

    1997-12-31

    Environment Canada and the Netherlands Energy Research Foundation are co-developers of a patented Self-Sealing/Self-Healing (SS/SH) Barrier system for containment of wastes which is licensed to Water Technology International Corporation. The SS/SH Barrier is intended for use as either a liner or cover for landfills, contaminated sites, secondary containment areas, etc., in the industrial, chemical, mining and municipal sectors, and also as a barrier to hydraulic flow for the transportation and construction industry. The SS/SH Barrier`s most significant feature is its capability for self-repair in the event of a breach. By contrast, conventional barrier systems, such as clay, geomembrane, or geosynthetic clay liners can not be repaired without laborious excavation and reconstruction. Laboratory investigations have shown that the SS/SH Barrier concept will function with a variety of reactive materials. Self-Sealing/Self-Healing Barriers are cost competitive and consistently exhibit hydraulic conductivities ranging from 10{sup -9} to 10{sup -13} m/s, which decrease with time. These measurements meet or exceed the recommended hydraulic conductivity required by EPA for clay liners (<1x10{sup -9} m/s) used in landfills and hazardous waste sites. Results of mineralogical examination of the seal, diffusion testing, hydraulic conductivity measurement, and durability testing, including wet/dry, freeze/thaw cycling and leachate compatibility are also presented.

  11. A novel "wastes-treat-wastes" technology: role and potential of spent fluid catalytic cracking catalyst assisted ozonation of petrochemical wastewater.

    Science.gov (United States)

    Chen, Chunmao; Yu, Ji; Yoza, Brandon A; Li, Qing X; Wang, Gang

    2015-04-01

    Catalytic ozonation is a promising wastewater treatment technology. However, the high cost of the catalyst hinders its application. A novel "wastes-treat-wastes" technology was developed to reuse spent fluid catalytic cracking catalysts (sFCCc) for the ozonation of petrochemical wastewater in this study. Multivalent vanadium (V(4+) and V(5+)), iron (Fe(2+) and Fe(3+)) and nickel (Ni(2+)) oxides that are distributed on the surface of sFCCc and poisoned FCC catalysts are the catalytic components for ozonation. The sFCCc assisted catalytic ozonation (sFCCc-O) of nitrobenzene indicated that the sFCCc significantly promoted hydroxyl radical mediated oxidation. The degradation rate constant of nitrobenzene in sFCCc-O (0.0794 min(-1) at 298 K) was approximately doubled in comparison with that in single ozonation (0.0362 min(-1) at 298 K). The sFCCc-O of petrochemical wastewater increased chemical oxygen demand removal efficiency by three-fold relative to single ozonation. The number of oxygen-containing (Ox) polar contaminants in the effluent (253) from sFCCc-O treatment decreased to about 70% of the initial wastewater (353). The increased oxygen/carbon atomic ratio and decreased number of Ox polar contaminants indicated a high degree of degradation. The present study showed the role and potential of sFCCc for catalytic ozonation of petrochemical wastewater, particularly in an advantage of the cost-effectiveness through "wastes-treat-wastes".

  12. Advanced materials for aerospace and biomedical applications: New glasses for hermetic titanium seals

    Energy Technology Data Exchange (ETDEWEB)

    Brow, R.K.; Tallant, D.R.; Crowder, S.V. [and others

    1996-11-01

    Titanium and titanium alloys have an outstanding strength-to-weight ratio and corrosion resistance and so are materials of choice for a variety of aerospace and biomedical applications. Such applications are limited by the lack of a viable hermetic glass sealing technology. Conventional silicate sealing glasses are readily reduced by titanium to form interfacial silicides that are incompatible with a robust glass/metal seal. Borate-based glasses undergo a similar thermochemistry and are reduced to a titanium boride. The kinetics of this reactions, however, are apparently slower and so a deleterious interface does not form. Chemically durable lanthanoborate glasses were examined as candidate sealing compositions. The compositions, properties, and structures of several alkaline earth, alumina, and titania lanthanoborate glass forming systems were evaluated and this information was used as the basis for a designed experiment to optimize compositions for Ti-sealing. A number of viable compositions were identified and sealing procedures established. Finally, glass formation, properties, and structure of biocompatible Fe{sub 2}O{sub 3}- and TiO{sub 2}-doped calcium phosphate systems were also evaluated.

  13. Reservoir characterization and seal integrity of Jemir field in Niger Delta, Nigeria

    Science.gov (United States)

    Adagunodo, Theophilus Aanuoluwa; Sunmonu, Lukman Ayobami; Adabanija, Moruffdeen Adedapo

    2017-05-01

    Ignoring fault seal and depending solely on reservoir parameters and estimated hydrocarbon contacts can lead to extremely unequal division of reserves especially in oil fields dominated by structural traps where faults play an important role in trapping of hydrocarbons. These faults may be sealing or as conduit to fluid flow. In this study; three-dimensional seismic and well log data has been used to characterize the reservoirs and investigate the seal integrity of fault plane trending NW-SE and dip towards south in Jemir field, Niger-Delta for enhanced oil recovery. The petrophysical and volumetric analysis of the six reservoirs that were mapped as well as structural interpretation of the faults were done both qualitatively and quantitatively. In order to know the sealing potential of individual hydrocarbon bearing sand, horizon-fault intersection was done, volume of shale was determined, thickness of individual bed was estimated, and quality control involving throw analysis was done. Shale Gouge Ratio (SGR) and Hydrocarbon Column Height (HCH) (supportable and structure-supported) were also determined to assess the seal integrity of the faults in Jemir field. The petrophysical analysis indicated the porosity of traps on Jemir field ranged from 0.20 to 0.29 and the volumetric analyses showed that the Stock Tank Original Oil in Place varied between 5.5 and 173.4 Mbbl. The SGR ranged from leaking (60%) fault plane suggesting poor to moderate sealing. The supportable HCH of Jemir field ranged from 98.3 to 446.2 m while its Structure-supported HCH ranged from 12.1 to 101.7 m. The porosities of Jemir field are good enough for hydrocarbon production as exemplified by its oil reserve estimates. However, improper sealing of the fault plane might enhance hydrocarbon leakage.

  14. Floating air riding seal for a turbine

    Energy Technology Data Exchange (ETDEWEB)

    Ebert, Todd A

    2016-08-16

    A floating air riding seal for a gas turbine engine with a rotor and a stator, an annular piston chamber with an axial moveable annular piston assembly within the annular piston chamber formed in the stator, an annular cavity formed on the annular piston assembly that faces a seal surface on the rotor, where the axial moveable annular piston includes an inlet scoop on a side opposite to the annular cavity that scoops up the swirling cooling air and directs the cooling air to the annular cavity to form an air cushion with the seal surface of the rotor.

  15. Vacuum-sealed casting process under pressure

    Institute of Scientific and Technical Information of China (English)

    LI Chen-xi; GUO Tai-ming; WU Chun-jing; WANG Hong

    2006-01-01

    A new casting method, the vacuum-sealed mold casting under pressure, has been developed, and thin wall iron castings with high precision and smooth surface have been produced successfully with this casting method. The experimental results show that the liquid iron has a very excellent filling ability because a high negative pressure is formed in the mold cavity during filling process. The vacuum-sealed mold under pressure has very high compressive strength greater than 650 kPa, which is 3-4 times as high as that of the molds produced by high-pressure molding process or vacuum-sealed molding process.

  16. Frequency of seal disruption with the sarns centrifugal pump in postcardiotomy circulatory assist.

    Science.gov (United States)

    Curtis, J J; Boley, T M; Walls, J T; Demmy, T L; Schmaltz, R A

    1994-03-01

    We have used the Sarns centrifugal pump for uni- or biventricular assist in 58 patients with postcardiotomy cardiogenic shock. This device utilizes a spinning impeller pump that is magnetically coupled to a motor imparting rotary motion to incoming perfusate. Nine patients (16%) experienced 22 device failures, which consisted of a nonvisible disruption of the seal within the pumphead. This allowed fluid to accumulate between the pumphead and the motor necessitating change of the pumphead. The time to seal disruption was 10-149 h (median 48). Of the 22 seal disruptions, 18 occurred in 73 left ventricular pumps (25%), and 4 occurred in 38 right ventricular pumps (11%) p = 0.015. Left ventricular pumps failed at 10-144 h (median 48), and right ventricular pumps failed at 48-149 h (median 83) p = 0.02. The Sarns centrifugal pump is dependable for its intended use of cardiopulmonary perfusion. However, when used for postcardiotomy assist, seal disruption should be expected. It occurs sooner and is more common during left ventricular assist. We recommend inspection of the magnet chamber for evidence of seal disruption every 12 h with left ventricular assist and every 24 h with right ventricular assist.

  17. Robustness of Modeling of Out-of-Service Gas Mechanical Face Seal

    Science.gov (United States)

    Green, Itzhak

    2007-01-01

    Gas lubricated mechanical face seal are ubiquitous in many high performance applications such as compressors and gas turbines. The literature contains various analyses of seals having orderly face patterns (radial taper, waves, spiral grooves, etc.). These are useful for design purposes and for performance predictions. However, seals returning from service (or from testing) inevitably contain wear tracks and warped faces that depart from the aforementioned orderly patterns. Questions then arise as to the heat generated at the interface, leakage rates, axial displacement and tilts, minimum film thickness, contact forces, etc. This work describes an analysis of seals that may inherit any (i.e., random) face pattern. A comprehensive computer code is developed, based upon the Newton- Raphson method, which solves for the equilibrium of the axial force and tilting moments that are generated by asperity contact and fluid film effects. A contact mechanics model is incorporated along with a finite volume method that solves the compressible Reynolds equation. Results are presented for a production seal that has sustained a testing cycle.

  18. Numerical analysis of erosion of the rotor labyrinth seal in a geothermal turbine

    Energy Technology Data Exchange (ETDEWEB)

    Mazur, Z.; Urquiza, G.; Campos, R. [Instituto de Investigaciones Electricas, Morelos (Mexico); Sierra, F. [Centro de Investigacion en Energia-UNAM, Morelos (Mexico)

    2002-10-01

    Excessive erosion of the labyrinth seal of a 100 MW geothermal turbine has been investigated. This study used computational fluid dynamics (CFD) and aims to identify one cause of erosion and a possible solution for substantially reducing it. The predictions were based upon a numerical calculation using a CFD model of the labyrinth seal with a water/steam flow containing hard solid particles and solved with a commercial CFD code: Fluent V5.0. The results confirmed the existence of flow conditions that play a major role in the rotor labyrinth seal erosion. Afterwards, the flow path was simulated with changes of rotor labyrinth seal geometry, which are indeed feasible of being implemented. The results confirmed that it is possible to reduce the erosion process by approximately 80% by incorporating a steam flow deflector in the fourth stage diaphragm, which changes the steam flow direction in the inlet zone to the rotor labyrinth seal channel, resulting in a reduction in steam volumetric mass flow and hard particle velocity by about 44%. (author)

  19. The Assessment of Sonic Waves and Tracer Gases as Non-Destructive Testing (NDT) Methods for In-Situ Underground Mine Seals

    OpenAIRE

    Brashear, Kyle Thomas

    2014-01-01

    Since the MINER Act of 2006, the minimum static load of in-situ underground mine seals has been increased from 20-psi to either 50-psi if monitoring is conducted or 120-psi if left unmonitored. These minimum strength requirements in seals must be designed, built, and maintained throughout the lifetime of the seal. Due to this, it has become necessary to assess the effectiveness of non-destructive testing (NDT) technologies to determine seal integrity, which in this case, are explored using so...

  20. 表面粗糙度对矩形动密封特性的影响∗%Effect of Surface Roughness on Dynamic Sealing Performance of Rectangular Elastomeric Seals

    Institute of Scientific and Technical Information of China (English)

    张付英; 赵龙; 李佳波

    2015-01-01

    Based on the numerical calculation flow of sealing property coupling of the elastic deformation, hydrodynam⁃ics and interference contact, the dynamic seal performances calculation of rectangular elastomeric seal was realized by u⁃sing Matlab software to program, and the parameters of oil film thickness, leakage and friction were got� The influence of surface roughness on the lubrication state and leakage was analyzed�The calculation results show that when the reciproca⁃ting velocity is constant, the lubrication state between sealing part and shift surface is changed from fluid lubrication into mixed lubrication with the increase of sealing ring roughness, and the leakage of sealing is also increased in a geometric, indicating that the roughness of seals has important influence on the serve life and sealing performance of the sealing ring�Reciprocating motion speed is also one of the key parameters that affect seal performance of rectangular sealing ring, when sealing pressure is certain, the critical speed for no leakage is reduced with the increase of sealing roughness.%基于耦合了密封圈的弹性变形、流体动力分析和过盈接触的密封性能数值计算流程,利用Matlab 软件编程实现矩形动密封特性的数值计算,得到矩形密封圈的油膜厚度、泄漏量及摩擦力等密封性能参数,分析表面粗糙度对矩形密封圈的润滑状态和泄漏量的影响。结果表明:往复运动速度一定时,随着密封圈粗糙度的增加,密封偶合面的润滑状态由流体润滑转变为润滑润滑状态,密封的泄漏量也呈几何式增加,说明粗糙度对密封圈的工作寿命和密封性能有较大的影响;往复运动速度也是影响矩形密封圈密封性能的关键工作参数之一,密封压力一定时,随着粗糙度的增加,不发生泄漏的临界速度降低。

  1. Rotordynamics and leakage - measurements and calculations on labyrinth gas seals and their application to large turbomachinery

    Energy Technology Data Exchange (ETDEWEB)

    Sobotzik, J.; Nordmann, R. [Technische Universitaet Darmstadt, Dept. of Mechatronic Systems, Darmstadt (Germany); Hiss, F. [Siemens Power Generation, Muelheim (Germany); Kwanka, K. [Technische Universitaet Muenchen, Muenchen (Germany)

    2000-07-01

    The flow in labyrinth gas seals can cause self-excited vibrations of the rotor. An exact prediction of these forces in the blueprint stage is necessary to estimate the dynamic behaviour of the rotor with the target to avoid such a vibration regime. In the past, a series of systematic experimental investigations of labyrinth seals with different geometries using new identification approach has been published. Computational Fluid Dynamics using Finite-Difference-Techniques allow the calculation of complex flow problems and deliver both leakage flow rate and rotordynamic coefficients. They consider optional laminar and turbulent flow conditions and fluid compressibility characteristics. This paper presents experimental rotordynamic coefficients and leakage rates of labyrinth gas seals of different shapes in comparison to values calculated by a finite-difference method. This validation should represent a further step on the way to possible improvements in the design of labyrinth seals. The importance of considering the stiffness as well as the damping coefficients in a rotordynamics design process is demonstrated for a large supercritical turbogenerator. (Author)

  2. Effect of bar sealing parameters on OPP/MCPP heat seal strength

    Directory of Open Access Journals (Sweden)

    2007-11-01

    Full Text Available The effect of bar sealing parameters on the heat seal strength of oriented polypropylene (OPP/metallic cast polypropylene (MCPP laminate film was investigated. Based on the results obtained from the parametric study, a bar sealing process window was developed. All points drop within the process window are combinations of platen temperature and dwell time that produce acceptable heat seal. Optimum combinations are indicated by the lower border of the window. The plateau initiation temperature, Tpi of OPP/MCPP laminate film used in the present study occurred before the final melting temperature, Tmf of the sealant material. The highest achievable heat seal strength was at the plateau region, and the corresponding failure modes were delaminating, tearing or combine failure modes (delaminating and tearing. Minimum pressure level of 1.25 bars is necessary to bring the laminate interface into intimate contact in order to effect sealing.

  3. Investigating the sealing capacity of a seal system in rock salt (DOPAS project)

    Energy Technology Data Exchange (ETDEWEB)

    Jantschik, Kyra; Moog, Helge C.; Czaikowski, Oliver; Wieczorek, Klaus [Gesellschaft fuer Anlagen- und Reaktorsicherheit (GRS) gGmbH, Braunschweig (Germany)

    2016-11-15

    This paper describes research and development work on plugging and sealing repositories, an issue of fundamental importance for the rock salt option which represents one of the three European repository options, besides the clay rock and the crystalline rock options. The programme aims at providing experimental data needed for the theoretical analysis of the long-term sealing capacity of concrete- based sealing materials. In order to demonstrate hydro-mechanical material stability under representative load scenarios, a comprehensive laboratory testing programme is carried out. This comprises investigation of the sealing capacity of the combined seal system and impact of the so-called excavation-damaged zones (EDZ) as well as investigation of the hydro-chemical long-term stability of the seal in contact with different brines under diffusive and advective conditions. This paper presents experimental approaches and preliminary results from laboratory investigations on salt concrete and combined systems as obtained to date.

  4. Research on Sealing Structure of Electro-hydraulic Servo Swing Motor%电液伺服摆动马达密封结构研究∗

    Institute of Scientific and Technical Information of China (English)

    李阁强; 赵巧莉; 李跃松; 郭冰菁

    2015-01-01

    为研究电液伺服摆动马达密封结构的性能,建立其密封件的有限元仿真模型,在相同预压缩量、不同介质压力条件下,对矩形密封结构、梯形密封结构、星形密封结构进行仿真分析,根据仿真结果比较3种密封结构的密封效果。结果表明,星形密封结构因其截面有4个密封唇,在沟槽中不易产生扭曲,耐压力较强,其密封有效性优于矩形密封结构,更适合用于大功率液压密封系统;梯形密封结构在靠近流体端具有较陡的压力梯度,在一端具有较缓的压力梯度,可以减小油膜厚度,从而减少泄漏量,因而其密封效果优于星形和矩形密封。%The finite element simulation model of the sealing structure of electro⁃hydraulic servo swing motor was estab⁃lished to study the performance of sealing structure�Three kinds of sealing structures, the rectangular sealing structure, the trapezoidal sealing structure, the star sealing structure were investigated by simulation method under the conditions of the same pre⁃compression and different medium pressure, and the sealing effect of three kinds of sealing structures were com⁃pared according to the results of simulation analysis�The results show that the star seal structure has four sealing lips on the cross⁃section and can avoid the distortion of seal structure in the groove, its sealing effectiveness is better than the rec⁃tangular seal structure and it is more suitable for high⁃power hydraulic sealing system�For the trapezoidal seal structure has a steeper pressure gradient near the fluid end and a moderate pressure gradient at one end, the leakage is reduced, and good sealing effect is achieved compared with the star and rectangular seal structure�

  5. EXPERIMENTAL APPARATUS FOR EXAMINATION OF MAGNETIC FLUID LUBRICATED THURST BEARING

    Directory of Open Access Journals (Sweden)

    Józef SALWIŃSKI

    2014-06-01

    Full Text Available In recent years, there has been development of the structure of thrust bearing with magnetic fluids . The essence of this type of bearing is to maintain a liquid lubricant in a very narrow gap with magnetic fluid by a magnetic field. Such systems can act as the bearing lubrication and sealing. This paper presents description of the experimental apparatus for examination magnetic fluid lubricated thrust bearing. Description of the construction and characteristics of the measuring possibilities ware presented.

  6. Flow—injection Chemiluminescence Determination of Reserpine in Medicine and Biological Fluids with Controlled—Reagent—Release Technology

    Institute of Scientific and Technical Information of China (English)

    宋正华; 张尼

    2003-01-01

    A sensitive and rapid chemiluminescence(CL) flow injection with controlled-reagent-release technology for the determination of reserpine was proposed.The Cl reagents,luminol and dichromate,uses in this sensor,were all immobilized on anion-exchange resin.Through injection of 100μl of water,the reagents on the anion-ex-change resin column were eluted and in the presence of reserpine ,the CL intensity was decreased,by which reserpine could be sensed.Reserpine was quantified by measuring the decrement of CL intensity,which was observed linear with the logrithm of reserpine concentration in the rage of 1.0-500.0ng/mL,and the limit of detection was 0.4ng/mL(3σ)with a relative standard deviation of less than 3.0?The proposed procedure was applied in the assay of reserpine in pharmaceutical preparation and biological fhuids without any pre-treatment process and with sampling frequencies of 72 times per hour.

  7. Finite Element Analysis of Elastomeric Seals for LIDS

    Science.gov (United States)

    Oswald, Jay J.; Daniels, Christopher C.

    2007-01-01

    Objective: Create a means of evaluating seals w/o prototypes. Motivation: Cost Prototype 54" seal approx.$100k per seal pair FEA license + high end workstation approx. $30k per year. Development time: 6 months lead time for a new seal design Many designs per day (solution time <1 minute) Understanding: Difficult to experimentally measure strains, contact pressure profile, stresses, displacements

  8. Sealing of ceramic SOFC-components with glass seals; Fuegen von keramischen Komponenten der Hochtemperatur-Brennstoffzellen mittels Glas- und Glaskeramikloten

    Energy Technology Data Exchange (ETDEWEB)

    Schillig, Cora

    2012-07-10

    The solid oxide fuel cell (SOFC) converts chemical energy of a fuel directly into electrical energy. However, for the implementation of SOFC-technology in competition to conventional power plants costs have to be reduced. The use of an alternative tubular cell design without closed end would allow reducing costs during cell manufacturing. However, this change in design makes a gastight sealing inside the generator near the gas inlet necessary. Different ceramic materials with varying coefficients of thermal expansion have to be sealed gastight and electrical insulating at temperatures between 850 C and 1000 C to prevent the gases from mixing and an electrical shortcut between the cells. This work comprises analysis of commercially available glass and glass-ceramic systems manufactured by Schott Electronic Packaging, Areva T and D and Ferro Corporation. Additionally new developed sealing glass and glass-ceramic systems were investigated and all systems were characterized fundamentally for the use as sealing material in SOFC generators. Therefore different test assemblies and series were conducted. Essential characteristics of a suitable sealing system are a thermal expansion coefficient between 9,5 and 12 . 10{sup -6}K{sup -1}, a viscosity in the range between 10{sup 4} to 10{sup 6} dPa{sup *}s and a wetting angle smaller than 90 during the sealing process. Also unwanted chemical side reactions between the sealing partners must be prevented, because a change in the phase composition or the creation of new phases in the sealing material could endanger the stability of the seal. Heat cycles, particularly those during generator operation, cause deterioration of the sealing material and subsequent reduction in its ability to prevent mixing of the gases. Sealant leaks can drastically impact efficiency of the generator. In order to ensure optimum operation low leak rates around 2,3 . 10{sup -4} mbar l/sec/cm{sup 2} must be maintained. Especially glass and glass

  9. Properties of Sealing Materials in Groundwater Wells

    DEFF Research Database (Denmark)

    Köser, Claus

    on the maximum swelling pressure; i) the bulk density of the sample, and ii) whether the sample is sorted or unsorted. CT scans (Computed Tomography) have been used to evaluate certain properties of bentonite seals in a limited volume. In this context, a set of algorithms to convert CT numbers (HU unit......) into densities for clay/water systems has been developed. This method has successfully been used to evaluate e.g., macroporosity, homogenization of the bentonite seal during the hydration of water, hydraulic conductivity and the creation of channels in the bentonite seals. Based on the results obtained...... in this Ph.D. thesis, a number of recommendations has been offered; i) a change regarding the production of pellets and ii) how sealing material must be treated in the actual construction of groundwater wells....

  10. HMSRP Hawaiian Monk Seal Photo Identification Database

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — This photo collection contains identification and other images and video of Hawaiian monk seals taken by PSD personnel and cooperating scientists as part of the...

  11. HMSRP Hawaiian Monk Seal Tag Data

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — This data set contains records for all tags applied to Hawaiian monk seals since 1981. These tags were applied by PSD personnel and cooperating scientists as part of...

  12. HMSRP Hawaiian Monk Seal Necropsy Data

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — This data set contains information on Hawaiian monk seal gross necropsy (in some cases only field notes or minimal information) and histopathology results beginning...

  13. HMSRP Hawaiian Monk Seals on Social Media

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — As social media platforms develop, they potentially provide valuable information for wildlife researchers and managers. NOAA’s Hawaiian Monk Seal Research Program...

  14. HMSRP Hawaiian Monk Seal Survey Data

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — This data set contains records of Hawaiian monk seal and green turtle sightings in the Northwestern Hawaiian Islands (NWHI) since 1982 at Lisianski Island, and since...

  15. HMSRP Hawaiian Monk Seal Survival Factors

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — This data set contains records of survival factors recorded by PSD personnel and cooperating scientists as part of the ongoing monk seal population assessment...

  16. Improved Gas Seal for Electrolytic Cells

    Science.gov (United States)

    Richter, R.

    1984-01-01

    Breakage by differential thermal expansion reduced. Cells for hot electrolysis of gases improved by design that reduces vulnerability of gas seals to breakage at operating temperature of about 1000 degrees C.

  17. HMSRP Hawaiian Monk Seal Fisheries Interactions data

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — The data set contains records of all documented hookings and/or entanglements of Hawaiian monk seals with actively fished gear, both commercial and recreational. The...

  18. Contamination and potential impacts to monk seals

    Data.gov (United States)

    US Fish and Wildlife Service, Department of the Interior — There are six main Hawaiian monk seal breeding colonies (French Frigate Shoals, Kure Atoll, Laysan Island, Lisianski Island, Pearl and Hermes Reef and Midway Atoll)...

  19. HMSRP Hawaiian Monk Seal Microsatellite Genotypes

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — Currently ~2,400 Hawaiian monk seal specimens have been analyzed genetically, providing genotypes at 18 microsatellite loci. These data are organized by individual,...

  20. Reactor coolant pump shaft seal stability during station blackout

    Energy Technology Data Exchange (ETDEWEB)

    Rhodes, D B; Hill, R C; Wensel, R G

    1987-05-01

    Results are presented from an investigation into the behavior of Reactor Coolant Pump shaft seals during a potential station blackout (loss of all ac power) at a nuclear power plant. The investigation assumes loss of cooling to the seals and focuses on the effect of high temperature on polymer seals located in the shaft seal assemblies, and the identification of parameters having the most influence on overall hydraulic seal performance. Predicted seal failure thresholds are presented for a range of station blackout conditions and shaft seal geometries.

  1. Troubleshooting ProSeal LMA

    Directory of Open Access Journals (Sweden)

    Bimla Sharma

    2009-01-01

    Full Text Available Supraglottic devices have changed the face of the airway management. These devices have contributed in a big way in airway management especially, in the difficult airway scenario significantly decreasing the pharyngolaryngeal morbidity. There is a plethora of these devices, which has been well matched by their wider acceptance in clinical practice. ProSeal laryngeal mask airway (PLMA is one such frequently used device employed for spontaneous as well as controlled ventilation. However, the use of PLMAat tunes maybe associated with certain problems. Some of the problems related with its use are unique while others are akin to the classic laryngeal mask airway (eLMA. However, expertise is needed for its safe and judicious use, correct placement, recognition and management of its various malpositions and complications. The present article describes the tests employed for proper confirmation of placementto assess the ventilatooy and the drain tube functions of the mask, diagnosis of various malpositions and the management of these aspects. All these areas have been highlighted under the heading of troubleshooting PLMA. Many problems can be solved by proper patient and procedure selection, maintaining adequate depth of anaesthesia, diagnosis and management of malpositions. Proper fixation of the device and monitoring cuff pressure intraopera-tively may bring down the incidence of airway morbidity.

  2. Aerodynamical sealing by air curtains

    Science.gov (United States)

    Frank, Daria; Linden, Paul

    2015-11-01

    Air curtains are artificial high-velocity plane turbulent jets which are installed in a doorway in order to reduce the heat and the mass exchange between two environments. The performance of an air curtain is assessed in terms of the sealing effectiveness E, the fraction of the exchange flow prevented by the air curtain compared to the open-door situation. The main controlling parameter for air curtain dynamics is the deflection modulus Dm representing the ratio of the momentum flux of the air curtain and the transverse forces acting on it due to the stack effect. In this talk, we examine the influence of two factors on the performance of an air curtain: the presence of an additional ventilation pathway in the room, such as a small top opening, and the effects of an opposing buoyancy force which for example arises if a downwards blowing air curtain is heated. Small-scale experiments were conducted to investigate the E (Dm) -curve of an air curtain in both situations. We present both experimental results and theoretical explanations for our observations. We also briefly illustrate how simplified models developed for air curtains can be used for more complex phenomena such as the effects of wind blowing around a model building on the ventilation rates through the openings.

  3. Controlling Fluid Flow in the Subsurface through Ureolysis-Controlled Mineral Precipitation

    Science.gov (United States)

    Gerlach, R.; Phillips, A. J.; Cunningham, A. B.; Spangler, L.

    2016-12-01

    In situ urea hydrolysis has been used by us successfully to manipulate the carbonate alkalinity and control the precipitation of carbonate minerals. Urea hydrolysis can be promoted using microbial cells, enzymes or thermal energy. This technology can be used to mitigate leakage pathways, seal fractures or control fluid transport in the subsurface in hydrocarbon production, enhanced geothermal energy storage, carbon sequestration, nuclear waste disposal, etc. We have completed two field demonstrations of the urea hydrolysis-controlled in situ mineral precipitation technology. The first demonstration showed fracture sealing was possible in a sandstone formation approx. 1120' below ground surface (bgs) and that the fracture had increased resistance to re-fracturing after mineralization treatment. The second field demonstration was performed in a well with an identified channel in the cement near the wellbore at approx. 1020' bgs. The in situ mineralization treatment resulted in reduced pressure decay during shut in periods and reduced injectivity. In addition, a noticeable difference was observed in the solids percentage in the ultrasonic imaging logs before and after biomineralization treatment. The presentation will summarize and put into context the field and our recent laboratory research focusing on permeability manipulation using the in situ ureolysis-driven mineralization technology under ambient and subsurface pressure conditions. We have demonstrated permeability reductions of 3-6 orders of magnitude in 100 µm to 4mm gaps between shale, sandstone and cement/steel interfaces.

  4. Design, construction and testing of underground seals

    CSIR Research Space (South Africa)

    Cook, AP

    2000-01-01

    Full Text Available extend into the workings and there cause bodily harm. If this does not happen it is still possible for the atmospheric by-products of the explosion, like lethal carbon monoxide, to filter into the workings through damaged seals. The most practical.... FOSROC. Installation guideline for Fosroc tekseal permanent ventilation seals, Company brochure. Foster-Miller Associates Inc. 1975. Design of reusable explosion proof bulkheads for a cross cut refuge chamber. USBM Contract Report H0133050, Pittsburgh...

  5. The Advantage of Sensor Sealing Laser Welding

    Institute of Scientific and Technical Information of China (English)

    YAN Yezhi; XU yu

    2007-01-01

    @@ Laser Welding Inevitably Applied in Sen sor Production Certain kinds of sensors such as pressure sensor,temperature sensor, optic-electronic sensor etc. utilize welding seal according to different application environment. With precision components and IC which is isolated by inert gas inside, these sensors should be sealed and able to resist the pressure. So the welding process must avoid distortion and harm to the components and IC.

  6. Anodizing And Sealing Aluminum In Nonchromated Solutions

    Science.gov (United States)

    Emmons, John R.; Kallenborn, Kelli J.

    1995-01-01

    Improved process for anodizing and sealing aluminum involves use of 5 volume percent sulfuric acid in water as anodizing solution, and 1.5 to 2.0 volume percent nickel acetate in water as sealing solution. Replaces process in which sulfuric acid used at concentrations of 10 to 20 percent. Improved process yields thinner coats offering resistance to corrosion, fatigue life, and alloy-to-alloy consistency equal to or superior to those of anodized coats produced with chromated solutions.

  7. Some Aspects of Sealed Nickel Cadmium Cells

    Directory of Open Access Journals (Sweden)

    P. K. Saha

    1967-11-01

    Full Text Available Sealed Nickel Cadmium Cell system is termed till today as the most reliable power pack for electronic apparatus specially in low temperature use. This paper brings out the development and production of sealed nickel cadmium cells of pocket plate construction. The author who has gained experience in production of Ni-Cd cells in East Germany discusses also the major problems faced by the battery manufactures of to-day.

  8. Emergency sacrificial sealing method in filters, equipment, or systems

    Science.gov (United States)

    Brown, Erik P

    2014-09-30

    A system seals a filter or equipment component to a base and will continue to seal the filter or equipment component to the base in the event of hot air or fire. The system includes a first sealing material between the filter or equipment component and the base; and a second sealing material between the filter or equipment component and the base and proximate the first sealing material. The first sealing material and the second seal material are positioned relative to each other and relative to the filter or equipment component and the base to seal the filter or equipment component to the base and upon the event of fire the second sealing material will be activated and expand to continue to seal the filter or equipment component to the base in the event of hot air or fire.

  9. Emergency sacrificial sealing method in filters, equipment, or systems

    Energy Technology Data Exchange (ETDEWEB)

    Brown, Erik P.

    2017-02-28

    A system seals a filter or equipment component to abase and will continue to seal the filter or equipment component to the base in the event of hot air or fire. The system includes a first sealing material between the filter or equipment component and the base; and a second sealing material between the filter or equipment component and the base and proximate the first sealing material. The first sealing material and the second seal material are positioned relative to each other and relative to the filter or equipment component and the base to seal the filter or equipment component to the base and upon the event of fire the second sealing material will be activated and expand to continue to seal the filter or equipment component to the base in the event of hot air or fire.

  10. Fibrin Sealants in Dura Sealing: A Systematic Literature Review.

    Directory of Open Access Journals (Sweden)

    Felice Esposito

    Full Text Available Fibrin sealants are widely used in neurosurgery to seal the suture line, provide watertight closure, and prevent cerebrospinal fluid leaks. The aim of this systematic review is to summarize the current efficacy and safety literature of fibrin sealants in dura sealing and the prevention/treatment of cerebrospinal fluid leaks.A comprehensive electronic literature search was run in the following databases: Cochrane Database of Systematic Reviews, Cochrane Central Resister of Controlled Trials, clinicaltrials.gov, MEDLINE/PubMed, and EMBASE. Titles and abstracts of potential articles of interest were reviewed independently by 3 of the authors.A total of 1006 database records and additional records were identified. After screening for duplicates and relevance, a total of 78 articles were assessed by the investigators for eligibility. Thirty-eight were excluded and the full-text of 40 articles were included in the qualitative synthesis. Seven of these included only safety data and were included in the safety assessment. The remaining 33 articles included findings from 32 studies that enrolled a total of 2935 patients who were exposed to fibrin sealant. Among these 33 studies there were only 3 randomized controlled trials, with the remaining being prospective cohort analysis, case controlled studies, prospective or retrospective case series. One randomized controlled trial, with 89 patients exposed to fibrin sealant, found a greater rate of intraoperative watertight dura closure in the fibrin sealant group than the control group (92.1% versus 38.0%, p0.05. Other clinical trials evaluated the effect of fibrin sealant in the postoperative prevention of cerebrospinal fluid leaks. These were generally lower level evidence studies (ie, not prospective, randomized, controlled trials that were not designed or powered to demonstrate a significant advantage to fibrin sealant use. Two small case series studies evaluated the effect of fibrin sealants in

  11. Caprock and overburden processes in geological CO2 storage: An experimental study on sealing efficiency and mineral alterations

    NARCIS (Netherlands)

    Wollenweber, J.; Alles, S.a.; Kronimus, A.; Busch, A.; Stanjek, H.; Krooss, B.M.

    2009-01-01

    A comprehensive set of experimental and analytical methods has been used to characterise the sealing and fluid -transport properties of fine-grained (pelitic) sedimentary rocks under the pressure and temperature conditions of geological CO2 storage. The flow experiments were carried out on

  12. Caprock and overburden processes in geological CO2 storage: An experimental study on sealing efficiency and mineral alterations

    NARCIS (Netherlands)

    Wollenweber, J.; Alles, S.a.; Kronimus, A.; Busch, A.; Stanjek, H.; Krooss, B.M.

    2009-01-01

    A comprehensive set of experimental and analytical methods has been used to characterise the sealing and fluid -transport properties of fine-grained (pelitic) sedimentary rocks under the pressure and temperature conditions of geological CO2 storage. The flow experiments were carried out on cylindric

  13. Predicting edge seal performance from accelerated testing

    Science.gov (United States)

    Hardikar, Kedar; Vitkavage, Dan; Saproo, Ajay; Krajewski, Todd

    2014-10-01

    Degradation in performance of a PV module attributable to moisture ingress has received significant attention in PV reliability research. Assessment of field performance of PV modules against moisture ingress through product-level testing in temperature-humidity control chambers poses challenges. Development of a meaningful acceleration factor model is challenging due to different rates of degradation of components embedded in a PV module, when exposed to moisture. Test results are typically a convolution of moisture barrier performance of the edge seal and degradation of laminated components when exposed to moisture. It is desirable to have an alternate method by which moisture barrier performance of the edge seal in its end product form can be assessed in any given field conditions, independent of particular cell design. In this work, a relatively inexpensive test technique was developed to test the edge seal in its end product form in a manner that is decoupled from other components of the PV module. A theoretical framework was developed to assess moisture barrier performance of edge seal with desiccants subjected to different conditions. This framework enables the analysis of test results from accelerated tests and prediction of the field performance of the edge seal. Results from this study lead to the conclusion that the edge seal on certain Miasole glass-glass modules studied is effective for the most aggressive weather conditions examined, beyond the intended service.

  14. Waste Isolation Pilot Plant Shaft Sealing System Compliance Submittal Design Report. Volume 1 and 2: Main report, appendices A, B, C, and D

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-08-01

    This report describes a shaft sealing system design for the Waste Isolation Pilot Plant (WIPP), a proposed nuclear waste repository in bedded salt. The system is designed to limit entry of water and release of contaminants through the four existing shafts after the WIPP is decommissioned. The design approach applies redundancy to functional elements and specifies multiple, common, low-permeability materials to reduce uncertainty in performance. The system comprises 13 elements that completely fill the shafts with engineered materials possessing high density and low permeability. Laboratory and field measurements of component properties and performance provide the basis for the design and related evaluations. Hydrologic, mechanical, thermal, and physical features of the system are evaluated in a series of calculations. These evaluations indicate that the design guidance is addressed by effectively limiting transport of fluids within the shafts, thereby limiting transport of hazardous material to regulatory boundaries. Additionally, the use or adaptation of existing technologies for placement of the seal components combined with the use of available, common materials assure that the design can be constructed.

  15. Self-balancing air riding seal for a turbine

    Energy Technology Data Exchange (ETDEWEB)

    Mills, Jacob A.

    2017-08-15

    A turbine of a gas turbine engine has an air riding seal that forms a seal between a rotor and a stator of the turbine, the air riding seal including an annular piston movable in an axial direction under the influence of a pressure on one side with a pressure acting on an opposite side that self-balances the air riding seal during the steady state condition of the engine and lifts off the seal during engine transients.

  16. Hermatically sealed motor blower unit with stator inside hollow armature

    Science.gov (United States)

    Donelian, Khatchik O.

    1976-01-20

    13. A hermetically sealed motor blower unit comprising, in combination, a sealed housing having a thrust plate mounted therein and having a re-entrant wall forming a central cavity in said housing, a rotor within said housing, said rotor comprising an impeller, a hollow shaft embracing said cavity and a thrust collar adapted to cooperate with said thrust plate to support the axial thrust of said shaft, one or more journal bearings within said housing for supporting the radial load of said shaft and electric motor means for rotating said rotor, said motor means comprising a motor-stator located within said cavity and adapted to cooperate through a portion of said re-entrant wall with a motor-rotor mounted within said hollow shaft, the portion of said re-entrant wall located between said motor-stator and said motor-rotor being made relatively thin to reduce electrical losses, the bearing surfaces of said thrust plate, thrust collar and journal bearings being in communication with the discharge of said impeller, whereby fluid pumped by said impeller can flow directly to said bearing surfaces to lubricate them.

  17. Synthetic Base Fluids

    Science.gov (United States)

    Brown, M.; Fotheringham, J. D.; Hoyes, T. J.; Mortier, R. M.; Orszulik, S. T.; Randles, S. J.; Stroud, P. M.

    The chemical nature and technology of the main synthetic lubricant base fluids is described, covering polyalphaolefins, alkylated aromatics, gas-to-liquid (GTL) base fluids, polybutenes, aliphatic diesters, polyolesters, polyalkylene glycols or PAGs and phosphate esters.Other synthetic lubricant base oils such as the silicones, borate esters, perfluoroethers and polyphenylene ethers are considered to have restricted applications due to either high cost or performance limitations and are not considered here.Each of the main synthetic base fluids is described for their chemical and physical properties, manufacture and production, their chemistry, key properties, applications and their implications when used in the environment.

  18. FRACTURING FLUID CHARACTERIZATION FACILITY

    Energy Technology Data Exchange (ETDEWEB)

    Subhash Shah

    2000-08-01

    Hydraulic fracturing technology has been successfully applied for well stimulation of low and high permeability reservoirs for numerous years. Treatment optimization and improved economics have always been the key to the success and it is more so when the reservoirs under consideration are marginal. Fluids are widely used for the stimulation of wells. The Fracturing Fluid Characterization Facility (FFCF) has been established to provide the accurate prediction of the behavior of complex fracturing fluids under downhole conditions. The primary focus of the facility is to provide valuable insight into the various mechanisms that govern the flow of fracturing fluids and slurries through hydraulically created fractures. During the time between September 30, 1992, and March 31, 2000, the research efforts were devoted to the areas of fluid rheology, proppant transport, proppant flowback, dynamic fluid loss, perforation pressure losses, and frictional pressure losses. In this regard, a unique above-the-ground fracture simulator was designed and constructed at the FFCF, labeled ''The High Pressure Simulator'' (HPS). The FFCF is now available to industry for characterizing and understanding the behavior of complex fluid systems. To better reflect and encompass the broad spectrum of the petroleum industry, the FFCF now operates under a new name of ''The Well Construction Technology Center'' (WCTC). This report documents the summary of the activities performed during 1992-2000 at the FFCF.

  19. DEVELOPMENT OF A CERAMIC TAMPER INDICATING SEAL: SRNL CONTRIBUTIONS

    Energy Technology Data Exchange (ETDEWEB)

    Krementz, D.; Brinkman, K.; Martinez-Rodriguez, M.; Mendez-Torres, A.; Weeks, G.

    2013-06-03

    Savannah River National Laboratory (SRNL) and Sandia National Laboratories (SNL) are collaborating on development of a Ceramic Seal, also sometimes designated the Intrinsically Tamper Indicating Ceramic Seal (ITICS), which is a tamper indicating seal for international safeguards applications. The Ceramic Seal is designed to be a replacement for metal loop seals that are currently used by the IAEA and other safeguards organizations. The Ceramic Seal has numerous features that enhance the security of the seal, including a frangible ceramic body, protective and tamper indicating coatings, an intrinsic unique identifier using Laser Surface Authentication, electronics incorporated into the seal that provide cryptographic seal authentication, and user-friendly seal wire capture. A second generation prototype of the seal is currently under development whose seal body is of Low Temperature Co-fired Ceramic (LTCC) construction. SRNL has developed the mechanical design of the seal in an iterative process incorporating comments from the SNL vulnerability review team. SRNL is developing fluorescent tamper indicating coatings, with recent development focusing on optimizing the durability of the coatings and working with a vendor to develop a method to apply coatings on a 3-D surface. SRNL performed a study on the effects of radiation on the electronics of the seal and possible radiation shielding techniques to minimize the effects. SRNL is also investigating implementation of Laser Surface Authentication (LSA) as a means of unique identification of each seal and the effects of the surface coatings on the LSA signature.

  20. Sealing Channeling and Chemical Flooding Composite Technology Research on the Heterogeneous Reservoir%非均质油藏封窜及化学驱复合技术研究

    Institute of Scientific and Technical Information of China (English)

    徐宏明; 侯吉瑞; 赵凤兰; 李伟娜; 张磊; 张建忠; 冷光耀

    2013-01-01

    利用单层均质模型及并联填砂管模型,评价改性淀粉凝胶体系的调剖性能.该凝胶体系由4%改性淀粉、4%丙烯酰胺单体、成胶控制剂按一定比例组成.凝胶体系成胶前的选择注入性良好,成胶后的残余阻力系数为834~2548,突破压力梯度高于50 MPa/m,封堵率大于99%,可有效解决水窜流问题.利用双层非均质岩心模型,考察3种后续驱替段塞对提高采收率的影响.由0.3%聚丙烯酰胺、0.3%烷基苯磺酸钠和0.1 g/L NaOH组成的三元驱、0.3%聚丙烯酰胺及水驱的采收率增幅分别为20%、17%和10%.“改性淀粉凝胶体系+三元复合驱”组合调驱中,改性淀粉凝胶可进一步开采高渗层位残余油,三元复合驱在封堵后可有效启动低渗层位,整体提高采收率37%.%The profile control characteristics of modified starch gel system were studied by monolayer homogeneous core model and parallel sand filling tube model. The gel composed of 4% modified starch, 4% acrylamide monomer and gelatinizing control agent in appropriate proportion. The results showed that the injection performance before gelling was good and the residual resistance factor was 834—2548 after gelling, breakthrough pressure gradient was greater than 50 MPa/m as well as the sealing rate was greater than 99%. So water channeling problem could be solved effectively. The influence of three flooding methods on enhanced oil recovery was evaluated based on double-layer inhomogeneous core model. The oil recovery ratio of ternary flooding including 0.3% polyacrylamide, 0.3% sodium alkyl benzene sulfonate and 0.1 g/L NaOH, 0.3% polyacrylamide flooding and water flooding was 20%, 17% and 10%, respectively. Residual oil in high permeability layer would be further produced by modified starch gel system. After gelling, oil in low permeability layer would be produced effectively by ternary flooding system. The recovery ratio increased 37% by combining modified