WorldWideScience

Sample records for fluid inclusion stratigraphy

  1. Identifying Fracture Types and Relative Ages Using Fluid Inclusion Stratigraphy

    Energy Technology Data Exchange (ETDEWEB)

    Dilley, Lorie M.; Norman, David; Owens, Lara

    2008-06-30

    Enhanced Geothermal Systems (EGS) are designed to recover heat from the subsurface by mechanically creating fractures in subsurface rocks. Understanding the life cycle of a fracture in a geothermal system is fundamental to the development of techniques for creating fractures. Recognizing the stage of a fracture, whether it is currently open and transmitting fluids; if it recently has closed; or if it is an ancient fracture would assist in targeting areas for further fracture stimulation. Identifying dense fracture areas as well as large open fractures from small fracture systems will also assist in fracture stimulation selection. Geothermal systems are constantly generating fractures, and fluids and gases passing through rocks in these systems leave small fluid and gas samples trapped in healed microfractures. Fluid inclusions trapped in minerals as the fractures heal are characteristic of the fluids that formed them, and this signature can be seen in fluid inclusion gas analysis. Our hypothesis is that fractures over their life cycle have different chemical signatures that we can see in fluid inclusion gas analysis and by using the new method of fluid inclusion stratigraphy (FIS) the different stages of fractures, along with an estimate of fracture size can be identified during the well drilling process. We have shown with this study that it is possible to identify fracture locations using FIS and that different fractures have different chemical signatures however that signature is somewhat dependent upon rock type. Open, active fractures correlate with increase concentrations of CO2, N2, Ar, and to a lesser extent H2O. These fractures would be targets for further enhancement. The usefulness of this method is that it is low cost alternative to current well logging techniques and can be done as a well is being drilled.

  2. Chemical Signatures of and Precursors to Fractures Using Fluid Inclusion Stratigraphy

    Energy Technology Data Exchange (ETDEWEB)

    Lorie M. Dilley

    2011-03-30

    Enhanced Geothermal Systems (EGS) are designed to recover heat from the subsurface by mechanically creating fractures in subsurface rocks. Open or recently closed fractures would be more susceptible to enhancing the permeability of the system. Identifying dense fracture areas as well as large open fractures from small fracture systems will assist in fracture stimulation site selection. Geothermal systems are constantly generating fractures (Moore, Morrow et al. 1987), and fluids and gases passing through rocks in these systems leave small fluid and gas samples trapped in healed microfractures. These fluid inclusions are faithful records of pore fluid chemistry. Fluid inclusions trapped in minerals as the fractures heal are characteristic of the fluids that formed them, and this signature can be seen in fluid inclusion gas analysis. This report presents the results of the project to determine fracture locations by the chemical signatures from gas analysis of fluid inclusions. With this project we hope to test our assumptions that gas chemistry can distinguish if the fractures are open and bearing production fluids or represent prior active fractures and whether there are chemical signs of open fracture systems in the wall rock above the fracture. Fluid Inclusion Stratigraphy (FIS) is a method developed for the geothermal industry which applies the mass quantification of fluid inclusion gas data from drill cuttings and applying known gas ratios and compositions to determine depth profiles of fluid barriers in a modern geothermal system (Dilley, 2009; Dilley et al., 2005; Norman et al., 2005). Identifying key gas signatures associated with fractures for isolating geothermal fluid production is the latest advancement in the application of FIS to geothermal systems (Dilley and Norman, 2005; Dilley and Norman, 2007). Our hypothesis is that peaks in FIS data are related to location of fractures. Previous work (DOE Grant DE-FG36-06GO16057) has indicated differences in the

  3. Fluid inclusion geothermometry

    Science.gov (United States)

    Cunningham, C.G.

    1977-01-01

    Fluid inclusions trapped within crystals either during growth or at a later time provide many clues to the histories of rocks and ores. Estimates of fluid-inclusion homogenization temperature and density can be obtained using a petrographic microscope with thin sections, and they can be refined using heating and freezing stages. Fluid inclusion studies, used in conjunction with paragenetic studies, can provide direct data on the time and space variations of parameters such as temperature, pressure, density, and composition of fluids in geologic environments. Changes in these parameters directly affect the fugacity, composition, and pH of fluids, thus directly influencing localization of ore metals. ?? 1977 Ferdinand Enke Verlag Stuttgart.

  4. Fluid inclusions in salt: an annotated bibliography

    Energy Technology Data Exchange (ETDEWEB)

    Isherwood, D.J.

    1979-01-26

    An annotated bibliography is presented which was compiled while searching the literature for information on fluid inclusions in salt for the Nuclear Regulatory Commission's study on the deep-geologic disposal of nuclear waste. The migration of fluid inclusions in a thermal gradient is a potential hazard to the safe disposal of nuclear waste in a salt repository. At the present time, a prediction as to whether this hazard precludes the use of salt for waste disposal can not be made. Limited data from the Salt-Vault in situ heater experiments in the early 1960's (Bradshaw and McClain, 1971) leave little doubt that fluid inclusions can migrate towards a heat source. In addition to the bibliography, there is a brief summary of the physical and chemical characteristics that together with the temperature of the waste will determine the chemical composition of the brine in contact with the waste canister, the rate of fluid migration, and the brine-canister-waste interactions.

  5. Fluid inclusions in salt: an annotated bibliography

    International Nuclear Information System (INIS)

    Isherwood, D.J.

    1979-01-01

    An annotated bibliography is presented which was compiled while searching the literature for information on fluid inclusions in salt for the Nuclear Regulatory Commission's study on the deep-geologic disposal of nuclear waste. The migration of fluid inclusions in a thermal gradient is a potential hazard to the safe disposal of nuclear waste in a salt repository. At the present time, a prediction as to whether this hazard precludes the use of salt for waste disposal can not be made. Limited data from the Salt-Vault in situ heater experiments in the early 1960's (Bradshaw and McClain, 1971) leave little doubt that fluid inclusions can migrate towards a heat source. In addition to the bibliography, there is a brief summary of the physical and chemical characteristics that together with the temperature of the waste will determine the chemical composition of the brine in contact with the waste canister, the rate of fluid migration, and the brine-canister-waste interactions

  6. An overview on current fluid-inclusion research and applications

    Science.gov (United States)

    Chi, G.; Chou, I.-Ming; Lu, H.-Z.

    2003-01-01

    This paper provides an overview of some of the more important developments in fluid-inclusion research and applications in recent years, including fluid-inclusion petrography, PVTX studies, and analytical techniques. In fluid-inclusion petrography, the introduction of the concept of 'fluid-inclusion assemblage' has been a major advance. In PVTX studies, the use of synthetic fluid inclusions and hydrothermal diamond-anvil cells has greatly contributed to the characterization of the phase behaviour of geologically relevant fluid systems. Various analytical methods are being developed and refined rapidly, with the Laser-Raman and LA-ICP-MS techniques being particularly useful for volatile and solute analyses, respectively. Ore deposit research has been and will continue to be the main field of application of fluid inclusions. However, fluid inclusions have been increasingly applied to other fields of earth science, especially in petroleum geology and the study of magmatic and earth interior processes.

  7. Fluid inclusion brine compositions from Palo Duro Basin salt sites

    International Nuclear Information System (INIS)

    Moody, J.B.

    1987-01-01

    The fluid inclusion analyses were done on salt samples from Lower San Andres Cycle 4 and 5. The stable isotope composition of the fluid inclusion brines was measured on duplicate samples taken from the same fluid inclusion brine for correlation of geochemical content with the stable isotopic content. The analyzed Palo Duro Basin salt fluid inclusions are predominantly one phase, i.e., the presence of a fluid only. However, many of the larger fluid inclusions do have a small vapor bubble. This liquid/vapor ratio is so high in these vapor-containing fluid inclusions that their behavior in a thermal gradient would be almost identical to that of all liquid inclusions. Closely associated with the fluid inclusions are cryptomelane where some fibers penetrate into halite host crystal. The fluid inclusions have a wide variability in content for those components that were analyzed, even within the same salt type. The fluid inclusion brines are also acidic, ranging from 3 to 6 as measured with pH test papers

  8. Re-Equilibration Processes in Fluid Inclusion Assemblages

    Directory of Open Access Journals (Sweden)

    Ronald J. Bakker

    2017-07-01

    Full Text Available Post-entrapment modifications reduce the reliability of fluid inclusions to determine trapping conditions in rock. Processes that may modify fluid inclusion properties are experimentally identified in this study using synthetic fluid inclusions in quartz with a well-defined composition and density. Modifications are characterized with microthermometry (homogenization and dissolution temperatures and Raman-spectroscopy in binary fluid systems H2O-D2O and H2O-NaCl. Three distinct processes were identified in this study: (1 diffusion of H2O and D2O; (2 crystal-recovery, expulsion of H2O and accumulation of quartz in inclusions (preferential H2O loss; (3 irreversible total volume increase at the α-β quartz transition. Diffusion is caused by H2O fugacity gradients and can be modelled according to classical diffusion models. The variability of re-equilibrated properties in fluid inclusion assemblages depends on time, temperature, diffusion distance and the size of fluid inclusions. Negative pressure gradients (internal under-pressure induce the crystal-recovery process, in which H2O is preferentially extracted from inclusions that simultaneously shrink by the inward growth of quartz. This process reduces the H2O concentration and increases the fluid density by total volume loss. Temperature and time are also controlling factors of this process, which is able to transport H2O against fugacity gradients.

  9. Methodologies for Reservoir Characterization Using Fluid Inclusion Gas Chemistry

    Energy Technology Data Exchange (ETDEWEB)

    Dilley, Lorie M. [Hattenburg Dilley & Linnell, LLC, Anchorage, AL (United States)

    2015-04-13

    The purpose of this project was to: 1) evaluate the relationship between geothermal fluid processes and the compositions of the fluid inclusion gases trapped in the reservoir rocks; and 2) develop methodologies for interpreting fluid inclusion gas data in terms of the chemical, thermal and hydrological properties of geothermal reservoirs. Phase 1 of this project was designed to conduct the following: 1) model the effects of boiling, condensation, conductive cooling and mixing on selected gaseous species; using fluid compositions obtained from geothermal wells, 2) evaluate, using quantitative analyses provided by New Mexico Tech (NMT), how these processes are recorded by fluid inclusions trapped in individual crystals; and 3) determine if the results obtained on individual crystals can be applied to the bulk fluid inclusion analyses determined by Fluid Inclusion Technology (FIT). Our initial studies however, suggested that numerical modeling of the data would be premature. We observed that the gas compositions, determined on bulk and individual samples were not the same as those discharged by the geothermal wells. Gases discharged from geothermal wells are CO2-rich and contain low concentrations of light gases (i.e. H2, He, N, Ar, CH4). In contrast many of our samples displayed enrichments in these light gases. Efforts were initiated to evaluate the reasons for the observed gas distributions. As a first step, we examined the potential importance of different reservoir processes using a variety of commonly employed gas ratios (e.g. Giggenbach plots). The second technical target was the development of interpretational methodologies. We have develop methodologies for the interpretation of fluid inclusion gas data, based on the results of Phase 1, geologic interpretation of fluid inclusion data, and integration of the data. These methodologies can be used in conjunction with the relevant geological and hydrological information on the system to

  10. Nuclear microscopy of fluid inclusions at the CSIRO

    International Nuclear Information System (INIS)

    Ryan, C.; Van Achterbergh, E.; Win, T.T.; McInnes, B.; Cripps, G.; Suter, G.; Liu, W.

    2003-01-01

    Full text: The deep penetration of a MeV energy proton beam and the predictable nature of X-ray production using proton induced X-ray emission (PIXE) make the nuclear microprobe ideally suited to the imaging and analysis of fluid and melt inclusions in minerals. MeV protons interact with a target through electronic interactions with a loss of ∼100 eV per collision. Such small energy loss leads to a smooth and predictable slowing down behaviour with a small energy uncertainty. Furthermore, the small momentum transfers in these collisions result in negligible spreading of the beam (e.g. ∼1 μm at 40 μm depth in quartz). Hence, the proton path can be regarded as linear. The principle mechanisms for proton energy loss, proton-induced ionization, secondary fluorescence and X-ray absorption and detection are understood and well characterized. This enables the integration of expected PIXE X-ray yields along the path of the proton beam and provides the foundation for a standardless microanalytical method. A strength of standardless PIXE analysis enables the approach to be extended to complex problems where the production of standards becomes impractical or unrepresentative of natural samples. One such problem is the study of ore metal transport and ore formation processes using the non-destructive analysis of fluids trapped as fluid inclusions in minerals using a raster-scanned proton probe. In this case, the integration of PIXE X-rays can be confined to the volume of the fluid inclusion in order to calculate the yield of elemental X-rays per ppm of an element. This calculation is illustrated, which shows one volume element of the fluid inclusion excited by the beam and the X-ray path to a detector. The CSIRO-GEMOC Nuclear Microprobe can focus a 3 MeV proton beam into a 1.3 μm beam spot for fluid inclusion analysis and intense beams for mineral imaging at 1.8 μm resolution (Ryan et al., 2001a). Quantitative elemental images are projected using the Dynamic Analysis

  11. 3D Volumetric Analysis of Fluid Inclusions Using Confocal Microscopy

    Science.gov (United States)

    Proussevitch, A.; Mulukutla, G.; Sahagian, D.; Bodnar, B.

    2009-05-01

    Fluid inclusions preserve valuable information regarding hydrothermal, metamorphic, and magmatic processes. The molar quantities of liquid and gaseous components in the inclusions can be estimated from their volumetric measurements at room temperatures combined with knowledge of the PVTX properties of the fluid and homogenization temperatures. Thus, accurate measurements of inclusion volumes and their two phase components are critical. One of the greatest advantages of the Laser Scanning Confocal Microscopy (LSCM) in application to fluid inclsion analsyis is that it is affordable for large numbers of samples, given the appropriate software analysis tools and methodology. Our present work is directed toward developing those tools and methods. For the last decade LSCM has been considered as a potential method for inclusion volume measurements. Nevertheless, the adequate and accurate measurement by LSCM has not yet been successful for fluid inclusions containing non-fluorescing fluids due to many technical challenges in image analysis despite the fact that the cost of collecting raw LSCM imagery has dramatically decreased in recent years. These problems mostly relate to image analysis methodology and software tools that are needed for pre-processing and image segmentation, which enable solid, liquid and gaseous components to be delineated. Other challenges involve image quality and contrast, which is controlled by fluorescence of the material (most aqueous fluid inclusions do not fluoresce at the appropriate laser wavelengths), material optical properties, and application of transmitted and/or reflected confocal illumination. In this work we have identified the key problems of image analysis and propose some potential solutions. For instance, we found that better contrast of pseudo-confocal transmitted light images could be overlayed with poor-contrast true-confocal reflected light images within the same stack of z-ordered slices. This approach allows one to narrow

  12. CO2 fluid inclusions in Jack Hills zircons

    Science.gov (United States)

    Menneken, Martina; Geisler, Thorsten; Nemchin, Alexander A.; Whitehouse, Martin J.; Wilde, Simon A.; Gasharova, Biliana; Pidgeon, Robert T.

    2017-08-01

    The discovery of Hadean to Paleoarchean zircons in a metaconglomerate from Jack Hills, Western Australia, has catalyzed intensive study of these zircons and their mineral inclusions, as they represent unique geochemical archives that can be used to unravel the geological evolution of early Earth. Here, we report the occurrence and physical properties of previously undetected CO2 inclusions that were identified in 3.36-3.47 Ga and 3.80-4.13 Ga zircon grains by confocal micro-Raman spectroscopy. Minimum P-T conditions of zircon formation were determined from the highest density of the inclusions, determined from the density-dependence of the Fermi diad splitting in the Raman spectrum and Ti-in-zircon thermometry. For both age periods, the CO2 densities and Ti-in-zircon temperatures correspond to high-grade metamorphic conditions (≥5 to ≥7 kbar/ 670 to 770 °C) that are typical of mid-crustal regional metamorphism throughout Earth's history. In addition, fully enclosed, highly disordered graphitic carbon inclusions were identified in two zircon grains from the older population that also contained CO2 inclusions. Transmission electron microscopy on one of these inclusions revealed that carbon forms a thin amorphous film on the inclusion wall, whereas the rest of the volume was probably occupied by CO2 prior to analysis. This indicates a close relationship between CO2 and the reduced carbon inclusions and, in particular that the carbon precipitated from a CO2-rich fluid, which is inconsistent with the recently proposed biogenic origin of carbon inclusions found in Hadean zircons from Jack Hills.

  13. Fluid inclusions and microstructures in experimentally deformed quartz single crystals

    Science.gov (United States)

    Thust, A.; Tarantola, A.; Heilbronner, R.; Stünitz, H.

    2009-04-01

    The "H2O-weakening" effect that reduces the strength of quartz dramatically (e.g. Griggs & Blacic 1965) is still not understood. For example, Kronenberg & Tullis (1984) conclude that the weakening effect is pressure dependent while Paterson (1989) infers a glide and recovery control of water. Obviously, the spatial distribution and transport of H2O are important factors (Kronenberg et al. 1986, FitzGerald et al. 1991). We have carried out experiments on milky quartz in a Griggs deformation apparatus. Cylinders (6.5 mm in diameter, 12-13 mm in length) from a milky zone of a natural quartz single crystal have been cored in orientations (1) normal to one of the prism planes and (2) 45˚ to and 45˚ to (O+orientation). At 1 GPa confining pressure, 900˚ C and 10-6s-1, the flow strength is 150 MPa for samples with orientation (1). Further experiments are needed to establish the flow strength for orientation (2). FTIR measurements on double-polished thick sections (200-500 μm) in the undeformed quartz material yield an average H2O content of approximately 100 H/106Si. The water is heterogeneously distributed in the sample. Direct measurements on fluid inclusions yield a H2O content of more than 25 000 H/106Si. Thus, the H2O in the undeformed material is predominantly present in fluid inclusions of size from tens to hundred microns. Micro-thermometric measurements at low temperature indicate the presence of different salts in the fluid inclusions. The ice melting temperature, between -6.9 and -7.4˚ C, indicate an average salinity of 10.5 wt% NaCl. After deformation the distribution of H2O is more homogeneous throughout the sample. The majority of the big inclusions have disappeared and very small inclusions of several microns to sub-micron size have formed. FTIR measurements in zones of undulatory extinction and shear bands show an average H2O content of approximately 3000 H/106Si. Moreover, the larger fluid inclusions are characterized by a higher salinity (12 wt%) due

  14. Hydrothermal Fluid evolution in the Dalli porphyry Cu-Au Deposit: Fluid Inclusion microthermometry studies

    Directory of Open Access Journals (Sweden)

    Alireza Zarasvandi

    2015-10-01

    Full Text Available Introduction A wide variety of world-class porphyry Cu deposits occur in the Urumieh-Dohktar magmatic arc (UDMA of Iran.The arc is composed of calc-alkaline granitoid rocks, and the ore-hosting porphyry intrusions are dominantly granodiorite to quartz-monzonite (Zarasvandi et al., 2015. It is believed that faults played an important role in the emplacement of intrusions and subsequentporphyry-copper type mineralization (Shahabpour, 1999. Three main centers host the porphyry copper mineralization in the UDMA: (1 Ardestan-SarCheshmeh-Kharestan zone, (2 Saveh-Ardestan district; in the central parts of the UDMA, hosting the Dalli porphyry Cu-Au deposit, and (3 Takab-Mianeh-Qharahdagh-Sabalan zone. Mineralized porphyry coppersystems in the UDMA are restricted to Oligocene to Mioceneintrusions and show potassic, sericitic, argillic, propylitic and locally skarn alteration (Zarasvandi et al., 2005; Zarasvandi et al., 2015. In the Dalli porphyry deposit, four hydrothermal alteration zones, includingpotassic, sericitic, propylitic, and argillic types have been described in the two discrete mineralized areas, namely, northern and southern stocks. Hypogenemineralization includes chalcopyrite, pyrite, and magnetite, with minor occurrences of bornite.Supergene activity has produced gossan, oxidized minerals and enrichment zones. The supergene enrichment zone contains chalcocite and covellite with a 10-20 m thickness. Mineralization in the northern stock is mainly composed of pyrite and chalcopyrite. The aim of this study is the investigation and classification of hydrothermal veins and the constraining of physicochemical compositions of ore-forming fluids using systematic investigation of fluid inclusions. Materials and methods Twenty samples were collected from drill holes. Thin and polished sections were prepared from hydrothermal veins of thepotassic, sericitic and propylitic alteration zones. Samples used for fluid inclusion measurements were collected

  15. On modifications of fluid inclusions in quartz : re-equilibration experiments and thermodynamical calculations on fluids in natural quartz

    NARCIS (Netherlands)

    Bakker, R.J.

    1992-01-01

    Fluids in rocks can be traced to great depths, and are found in crustal rocks as well as in mantle rocks. Information about the deep fluid which is obtained from fluid inclusions must be handled with care, for the way up after entrapment in a crystal is long and full of interferences at different

  16. Fluid inclusions in coesite-bearing eclogites and jadeite quartzite at Shuanghe, Dabie Shan (China).

    NARCIS (Netherlands)

    Fu, B.; Touret, J.L.R.; Zheng, Y.-F.

    2001-01-01

    Fluid inclusions in coesite-bearing eclogites and jadeite quartzite at Shuanghe in Dabie Shan, East-central China, have preserved remnants of early, prograde and/or peak metamorphic fluids, reset during post-UHP (ultrahigh-pressure) metamorphic uplift. Inclusions occur in several minerals (e.g.

  17. The fluid inclusion study in petroleum exploration; O estudo de inclusoes fluidas na exploracao de petroleo

    Energy Technology Data Exchange (ETDEWEB)

    Coelho, Carlos Eduardo Silva [PETROBRAS, Rio de Janeiro, RJ (Brazil). Centro de Pesquisas. Gerencia da Geoquimica]. E-mail: cescoelho@petrobras.com.br

    2005-05-01

    Several oil companies and research centers have been studying petroleum fluid inclusions in reservoirs since the 1980's. The first works have used the fluid inclusion microthermometry technique in order to interpret the thermal history and petroleum migration in relation to the burial history and diagenesis. Lately, the micro thermometric data is being used as a calibration parameter for thermal history modeling in sedimentary basins and reservoirs. Recently, new fluid inclusion study techniques are being used in petroleum exploration. Geochemical data of low molecular weight (up to C{sub 15}) oil-bearing fluid inclusions has been used with the purpose of pinpointing oil-bearing intervals in wells that have not revealed the presence of oil by conventional techniques. Molecular geochemical analyses of oils inside the inclusions technique enable oil-source correlations, oil-oil correlations, and maturity determination. (author)

  18. The non-destructive analysis of fluid inclusions in minerals using the proton microprobe

    Energy Technology Data Exchange (ETDEWEB)

    Ryan, C.G.; Van Achterbergy, E. [Commonwealth Scientific and Industrial Research Organisation (CSIRO), North Ryde, NSW (Australia). Div. of Exploration Geoscience; Heinrich, C.A. [ETH Zentrum, Zurich, (Switzerland). Department Erdwissenschaften; Mernagh, T.P. [Max-Planck-Institut fuer Chemie (Otto-Hahn-Institut), Mainz (Germany); Zaw, K. [Tasmania Univ., Sandy Bay, TAS (Australia)

    1996-12-31

    The study of ore forming fluids trapped as fluid inclusions in minerals is the key to understanding fluid flow paths at the time of ore formation and to predicting the location of ore bodies within large-scale magmatic hydrothermal systems. The large penetration depths and the predictable nature of MeV proton trajectories and X-ray absorption enables reliable modelling of PIXE yields and the development of standardless quantitative analytical methods. This permits quantitative microanalysis of minerals at ppm levels, and more recently has enabled the development of methods for quantitative trace-element imaging and the quantitative, non-destructive analysis of individual fluid inclusions. This paper reports on recent developments in Proton Microprobe techniques with special emphasis on ore systems and fluid inclusion analysis. 6 refs., 2 figs.

  19. The non-destructive analysis of fluid inclusions in minerals using the proton microprobe

    International Nuclear Information System (INIS)

    Ryan, C.G.; Van Achterbergy, E.; Zaw, K.

    1996-01-01

    The study of ore forming fluids trapped as fluid inclusions in minerals is the key to understanding fluid flow paths at the time of ore formation and to predicting the location of ore bodies within large-scale magmatic hydrothermal systems. The large penetration depths and the predictable nature of MeV proton trajectories and X-ray absorption enables reliable modelling of PIXE yields and the development of standardless quantitative analytical methods. This permits quantitative microanalysis of minerals at ppm levels, and more recently has enabled the development of methods for quantitative trace-element imaging and the quantitative, non-destructive analysis of individual fluid inclusions. This paper reports on recent developments in Proton Microprobe techniques with special emphasis on ore systems and fluid inclusion analysis. 6 refs., 2 figs

  20. Fluid inclusion, geochemical, Rb-Sr and Sm-Nd isotope studies on ...

    Indian Academy of Sciences (India)

    10

    54 part of Aravalli craton (Crawford and Compston 1970; Choudhry et al. 1984; Tobisch. 55 et al. 1994, Torsvik et al. 2001a; Pandit et al. 2003; Ashwal et al. .... 119. Fluid inclusions were observed in greisen quartz from Degana and Balda granites. 120. The isolated and randomly distributed inclusions are classified as ...

  1. Fluid Characteristics in the Giant Quartz Reef System of the Bundelkhand Craton, India: Constraints from Fluid Inclusion Study

    Science.gov (United States)

    Rout, D.; Panigrahi, M. K.; Pati, J. K.

    2017-12-01

    Giant quartz reefs are anomalous features indicating extensive mobilization of silica in the crust. Such reefs in the Abitibi belt, Canada and elsewhere are believed to be the result of activity of fluid of diverse sources on terrain boundaries. The Bundelkhand granitoid complex constituting a major part of the Bundelkhnad Craton in north-Central India is traversed by numerous such quartz reefs all across for a length of about 500 km. There are about 20 major reefs having dimensions of 35 to 40 km in length, 50 to 60 m in width standing out as prominent ridges in the region. Almost all are aligned parallel to each other in a sub-vertical to vertical manner following the NE-SW to NNE-SSW trend. Fluid inclusion petrography in quartz from these reefs reveal four types of inclusions viz. aqueous biphase (type-I), pure carbonic (type-II), aqueous carbonic (type-III) and polyphase (type-IV) inclusions. The type-I aqueous biphase inclusions are the dominant type in all the samples studied so far. Salinities calculated from temperature of melting of last ice (Tm) values are low to moderate, ranging from 0.18 to 18.19 wt% NaCl equivalents. Temperature of liquid-vapor homogenization (Th) values of these inclusions show a wide range from 101 ºC to 386 ºC (cluster around 150-250 ºC) essentially into liquid phase ruling out boiling during its course of evolution. Besides, aqueous Biphase inclusions, some data on pure CO2 inclusions furnish a near constant value of TmCO2 at -56.6 ºC in the Bundelkhand Craton indicating absence of CH4. Bivariate plot between Th and salinity suggest three possible water types which are controlling the overall activity of fluid in quartz reefs of Bundelkhand Craton viz. low-T low saline, high-T low saline and moderate-T and moderate saline. A low saline and CO2-bearing and higher temperature nature resembles a metamorphic fluid that may be a source for these giant quartz reefs. The low temperature low-salinity component could be a meteoric

  2. The Cocos Ridge hydrothermal system revealed by microthermometry of fluid and melt inclusions

    Science.gov (United States)

    Brandstätter, J.; Kurz, W.; Krenn, K.

    2017-12-01

    Microthermometric analyses of fluid and melt inclusions in hydrothermal veins and in the Cocos Ridge (CCR) basalt were used to reveal the CCR thermal history at IODP Site 344-U1414 and to constrain fluid source and flow. Hydrothermal veins are hosted by lithified sediments and CCR basalt . Site 344-U1414, located 1 km seaward of the Middle American Trench offshore Costa Rica, serves to evaluate fluid/rock interaction, the hydrologic system and geochemical processes linked with the tectonic evolution of the incoming Cocos Plate from the Early Miocene up to recent times. The veins in the sedimentary rocks are mainly filled by blocky calcite, containing numerous fluid inclusions, and sometimes crosscut fibrous quartz/chalcedony veins. The veins in the basalt can be differentiated into three types: antitaxial fibrous calcite veins, composite veins with fibrous calcite and clay minerals at the vein margins and spherulitic quartz in the center, and syntaxial blocky aragonite veins surrounded by a clay selvage in the uppermost CCR basalt sections. Secondary minerals, clay minerals, fibrous calcite, quartz/chalcedony and pyrite also filled vesicles in the basalt. Fluid inclusions were mainly found in the aragonite veins and rarely in quartz in the composite veins and vesicles. Blocky veins with embedded wall rock fragments appear in the sediments and in the basalt indicate hydraulic fracturing. The occurrence of decrepitated fluid inclusions show high homogenization temperatures up to 400 °C. Decrepitated fluid inclusions are formed by increased internal overpressure, related to isobaric heating. Elongated fluid inclusion planes, arc-like fluid inclusions and low homogenization temperatures indicate subsequent isobaric cooling. The results obtained so far from Raman spectroscopy and microthermometry indicate CO2 inclusions and petrographic observations suggest the presence of silicate melt inclusions in phenocrysts in the basalt (mainly in clinopyroxene and plagioclase

  3. Trace element analyses of fluid inclusions using laser ablation ICP-MS

    Directory of Open Access Journals (Sweden)

    Cong-ying Li

    2018-03-01

    Full Text Available Fluid inclusions are records of the physico-chemical conditions of fluid–rock interactions during magmatism, mineralization and fluid percolation and mixing processes. Laser ablation inductively coupled plasma mass spectrometry (LA-ICP-MS is a powerful tool for in situ analyses of small samples at micrometer levels. Here we report in situ analyses of fluid inclusions using LA-ICP-MS method. NIST SRM glasses and 23Na are generally used as external and internal standards for LA-ICP-MS analysis of fluid inclusion, respectively, although the RSD of microthermometric estimation of 23Na is about 20% and even worse, the background signal of Na is high for most ICP-MS. Using well-characterized natural fluids inclusion, we show that RESOlution S-155 laser system analyze fluid inclusions in quartz and determine the trace element concentrations. Resonetics RESOlution S-155 laser has the advantage of the motorized Z stage can be used to accommodate variation of sample height or sample topography and height difference between samples, which is very important for analyzing the fluid inclusion in quartz. Our results suggest laser energy density is 25 J/cm2, laser pulse repetition rates are commonly between 6 and 10 Hz to avoid the fissuring of quartz and obtain adequate results. For this LA-ICP-MS analysis, uncertainty on 35Cl content is around 40% because of intensity of the 35Cl signal is three orders of magnitude less intense than the intensity of the 23Na signal. Nevertheless, it is still a useful reference for fluid inclusion analyses in addition to 23Na. This technique can be applied to a range of hydrothermal geology problems, including determining the origins of ore forming brines and ore deposition processes, mapping metamorphic and hydrothermal fluid provinces and pathways, and constraining the effects of fluid–rock reactions and fluid mixing.

  4. Influence of H2O Rich Fluid Inclusions on Quartz Deformation

    Science.gov (United States)

    Thust, Anja; Heilbronner, Renée.; Stünitz, Holger; Tarantola, Alexandre; Behrens, Harald

    2010-05-01

    The effect of H2O on the strength of quartz is well known and has been discussed many times in the literature (e.g. Griggs & Blacic 1965, Kronenberg 1994). In this project we study the H2O interactions between natural dry quartz and H2O rich fluid inclusions during deformation in the solid medium Griggs apparatus. High pressure and temperature experiments were carried out using a quartz single crystal containing a large number of H2O-rich fluid inclusions. Adjacent to the fluid inclusions the crystal is essentially dry (micro thermometry. They show a large range in size from 50 μm to 700 μm and their spatial distribution is extremely heterogeneous. After deformation the inclusions are more homogeneously distributed throughout the sample and dramatically reduced in size (water). After deformation, the absorption spectra display a discrete peak, indicating OH- bonding in the quartz lattice. The release of H2O from fluid inclusions is an important process for crystal plastic deformation. Fluid inclusion rupture, micro cracking and the fast crack healing at these temperatures promote the distribution of H2O through the quartz and influences the strength of the material. Reference: Griggs, D.T. & Blacic, J.D., 1965: Quartz: Anomalous weakness of synthetic crystals. Science 174, 293-295. Kronenberg A.K., (1994): Hydrogen specifications and chemical weakening of quartz, Rev. Mineral. Ser. 29 (1994), pp. 123-176.

  5. Gas Analysis of Geothermal Fluid Inclusions: A New Technology For Geothermal Exploration

    Energy Technology Data Exchange (ETDEWEB)

    David I. Norman; Joseph Moore

    2004-03-09

    To increase our knowledge of gaseous species in geothermal systems by fluid inclusion analysis in order to facilitate the use of gas analysis in geothermal exploration. The knowledge of gained by this program can be applied to geothermal exploration, which may expand geothermal production. Knowledge of the gas contents in reservoir fluids can be applied to fluid inclusion gas analysis of drill chip cuttings in a similar fashion as used in the petroleum industry. Thus the results of this project may lower exploration costs both in the initial phase and lower drill hole completion costs. Commercial costs for fluid inclusion analysis done on at 20 feet intervals on chip samples for 10,000 ft oil wells is about $6,000, and the turn around time is a few weeks.

  6. Fluid inclusion studies of calcite veins from Yucca Mountain, Nevada, Tuffs: Environment of formation

    International Nuclear Information System (INIS)

    Roedder, E.; Whelan, J.F.; Vaniman, D.T.

    1994-01-01

    Calcite vein and vug fillings at four depths (130-314m), all above the present water table in USW G-1 bore hole at Yucca Mountain, Nevada, contain primary fluid inclusions with variable vapor/liquid raitos: Most of these inclusions are either full of liquid or full of vapor. The liquid-filled inclusions show that most of the host calcite crystallized from fluids at 2 vapor phase at ''<100 degrees C''. Our new studies reveal the additional presence of major methane in the vapor-filled inclusion, indicating even lower temperatures of trapping, perhaps at near-surface temperatures. They also show that the host calcite crystals grew from a flowing film of water on the walls of fractures open to the atmosphere, the vapor-filled inclusions representing bubbles that exsolved from this film onto the crystal surface

  7. Fluid inclusion studies of calcite veins from Yucca Mountain, Nevada, Tuffs: Environment of formation

    International Nuclear Information System (INIS)

    Roedder, E.; Whelan, J.F.; Vaniman, D.T.

    1994-01-01

    Calcite vein and vug fillings at fourth depths (130-314m), all above the present water table in USW G-1 bore hole at Yucca Mountain, Nevada, contain primary fluid inclusions with variable vapor/liquid ratios: most of these inclusions are either full of liquid or full of vapor. The liquid-filled inclusions show that most of the host calcite crystallized from fluids at 2 vapor phase at open-quotes 100 degrees Cclose quotes. Our new studies reveal the additional presence of major methane in the vapor-filled inclusion, indicating even lower temperatures of trapping, perhaps at near-surface temperatures. They also show that the host calcite crystals grew from a flowing film of water on the walls of fractures open to the atmosphere, the vapor-filled inclusions representing bubbles that exsolved from this film onto the crystal surface

  8. Pressure–Temperature–Fluid Constraints for the Poona Emerald Deposits, Western Australia: Fluid Inclusion and Stable Isotope Studies

    Directory of Open Access Journals (Sweden)

    Dan Marshall

    2016-12-01

    Full Text Available Emerald from the deposits at Poona shows micrometre-scale chemical, optical, and cathodoluminescence zonation. This zonation, combined with fluid inclusion and isotope studies, indicates early emerald precipitation from a single-phase saline fluid of approximately 12 weight percent NaCl equivalent, over the temperature range of 335–525 °C and pressures ranging from 70 to 400 MPa. The large range in pressure and temperature likely reflects some post entrapment changes and re-equilibration of oxygen isotopes. Secondary emerald-hosted fluid inclusions indicate subsequent emerald precipitation from higher salinity fluids. Likewise, the δ18O-δD of channel fluids extracted from Poona emerald is consistent with multiple origins yielding both igneous and metamorphic signatures. The combined multiple generations of emerald precipitation, different fluid compositions, and the presence of both metamorphic and igneous fluids trapped in emerald, likely indicate a protracted history of emerald precipitation at Poona conforming to both an igneous and a metamorphic origin at various times during regional lower amphibolite to greenschist facies metamorphism over the period ~2710–2660 Ma.

  9. Analysis of I-Br-Cl in single fluid inclusions by LA-ICP-MS

    Science.gov (United States)

    Giehl, C.; Fusswinkel, T.; Beermann, O.; Garbe-Schönberg, D.; Scholten, L.; Wagner, T.

    2017-12-01

    Halogens are excellent tracers of hydrothermal fluid sources and in-situ LA-ICP-MS analysis of Cl and Br in single fluid inclusions has provided fundamentally new insight into hydrothermal fluid flow and ore formation. There is mounting evidence that enrichment and depletion of Br relative to Cl may be caused by a number of processes beyond seawater evaporation and halite dissolution which cannot be discriminated on the basis of Br/Cl ratios alone. Expanding the analytical capabilities of fluid inclusion LA-ICP-MS analysis to include iodine would allow to discern between selective and coupled enrichment processes of Cl, Br and I, even in geologically complex samples that are inaccessible to bulk extraction techniques. We present iodine concentration data determined by LA-ICP-MS analysis of synthetic fluid inclusions, using the Sca17 scapolite reference material for external standardization (Seo et al., 2011). Iodine concentrations in Sca17 were determined using the Durango apatite standard. Four starting solutions containing I (0.3, 1.5, 27, 78 µg/g), Br (941, 1403, 2868, 4275 µg/g), Na (30.7, 94.7 mg/g), and Cl (50, 137 mg/g) (analyzed by ICP-OES and ICP-MS at CAU Kiel) were prepared by dissolving reagent grade chemical powders in ultra-pure water. Spherical inclusions (up to 40 µm) were synthesized from the starting solutions in pre-cracked, HF-treated synthetic quartz crystals which were placed in gold capsules and equilibrated at 600°C, 100/200 MPa in cold seal pressure vessels. Fluid inclusion LA-ICP-MS analysis (University of Helsinki) yielded average I concentrations in excellent agreement with the starting solutions (27.3 µg/g ± 14 %RSD for the 27 µg/g solution and 77.6 µg/g ± 8.3 %RSD for the 78 µg/g solution). Average Br and I concentrations deviate less than 10 % from solution concentration values. For the low I concentration solutions, the synthetic inclusions were too small to detect I. Thus, given suitable standard materials and sufficient

  10. Analysis of single oil-bearing fluid inclusions in mid-Proterozoic sandstones (Roper Group, Australia)

    Science.gov (United States)

    Siljeström, Sandra; Volk, Herbert; George, Simon C.; Lausmaa, Jukka; Sjövall, Peter; Dutkiewicz, Adriana; Hode, Tomas

    2013-12-01

    Hydrocarbons and organic biomarkers extracted from black shales and other carbonaceous sedimentary rocks are valuable sources of information on the biodiversity and environment of early Earth. However, many Precambrian hydrocarbons including biomarkers are suspected of being younger contamination. An alternative approach is to study biomarkers trapped in oil-bearing fluid inclusions by bulk crushing samples and subsequently analysing the extracted hydrocarbons with gas chromatography-mass spectrometry. However, this method does not constrain the hydrocarbons to one particular oil inclusion, which means that if several different generations of oil inclusions are present in the sample, a mix of the content from these oil inclusions will be analysed. In addition, samples with few and/or small inclusions are often below the detection limit. Recently, we showed that it is possible to detect organic biomarkers in single oil-bearing fluid inclusions using time-of-flight secondary ion mass spectrometry (ToF-SIMS). In the present study, single fluid inclusion analysis has been performed on Proterozoic samples for the first time. Four individual oil-bearing fluid inclusions, found in 1430 Ma sandstone from the Roper Superbasin in Northern Australia, were analysed with ToF-SIMS. The ToF-SIMS spectra of the oil in the different inclusions are very similar to each other and are consistent with the presence of n-alkanes/branched alkanes, monocyclic alkanes, bicyclic alkanes, aromatic hydrocarbons, and tetracyclic and pentacyclic hydrocarbons. These results are in agreement with those obtained from bulk crushing of inclusions trapped in the same samples. The capability to analyse the hydrocarbon and biomarker composition of single oil-bearing fluid inclusions is a major breakthrough, as it opens up a way of obtaining molecular compositional data on ancient oils without the ambiguity of the origin of these hydrocarbons. Additionally, this finding suggests that it will be possible

  11. Fluid inclusion constraints on the genesis of the Puladi muscovite deposit in Gongshan County, Yunnan Province

    Science.gov (United States)

    Yin, Qiong; Liu, Wei

    2017-12-01

    This paper focuses on beryl mines in the Maji region of Yunnan Province, which are characterized by fluid inclusions. Based on petrography theory, mineralogy, and ore-forming geological conditions, beryl can be divided as CO2 and CO2-H2O inclusions. In addition, the characteristics of inclusions in the coordinate of A/B is summarized. The homogenization temperature of fluid inclusions in the coordinate of A ranges from 250 °C to 397 °C, while the salinity of fluid inclusions ranges from 0.18% to 4.27%. By contrast, the homogenization temperature in the coordinate of B ranges from 210 °C to 340 °C, and the salinity is from 0.22% to 5.11%. The pressure of ore-forming fluid in the coordinate of A/B is approximately 83 MPa with densities of 0.8034 g/m3 and 0.8363 g/m3, which are characteristic of mediumtemperature, low-salinity, and medium-density fluids. Based on Raman spectra and different metallogenic depths, the two types of beryl belong to different metallogenic belts. The beryl deposits in Gongshan are of medium-temperature gas–hydrothermal type.

  12. Geological setting of silica in Dehnow-Abid region (Eshghabad northeast using fluid inclusions studies

    Directory of Open Access Journals (Sweden)

    Omid Yazdanpanah

    2017-02-01

    Full Text Available Introduction Dehnow-Abid area is a part of the geological map of Eshghabad with scale 1:100000 (Aghanabati, 1994 that is located about 20 kilometers northeast of Eshghabad and in the coordinates of 57° 6´ 0" to 57° 10´ 0" eastern longitude and 34° 28´ 0" to 34 21´ 0" northern latitude. The Dehnow-Abid area is located in Tabas block and east of central Iran structural zone. The small continent east central Iran (Takin, 1972 includes blocks: Loot, Tabas and Yazd that constitute Iran's eastern part (Davoudzadeh and Schmidt, 1982. In geology, we can acquire more information about temperature forming minerals and rocks, pressure, density of the fluid and the chemical composition of the ore bearing fluids by fluid inclusions studies. Properties as well as their role in our understanding of the sources and evolution of ore bearing hydrothermal fluids and genesis of mineral deposits are very important (Rodder, 1979. In this study, we tried to use both field and laboratory studies, including petrography and thermometry studies of fluid inclusions, environment formation of quartz in the specified Dehno-Abid. Materials and methods At first, in order to identify the area, the 1:100000 map of Eshghabad was used. Then, for a complete cognition of mentioned area, after a few field visits and sampling of outcrops of quartz, we prepared 16 double polishing sections from some crystalline and milky quartz. Then, 10 thin sections of sandstones of that area were prepared for identification the host rock. Microscopic examinations on fluid inclusions were done by a LEICA DMLSP polarizing light microscope. Fluid inclusion micro-thermometry studies were done by using a Linkam THM S600 heating and freezing stage and with a TMS94 controller. Also, a cooling LNP which is mounted on an Olympus BX-41 microscope in Laboratory Fluid inclusion of Earth Sciences, Damghan University was used. Discussion and results Lithology of the Dehnow-Abid area included dark shale

  13. World Wide Web Access to Fluid Inclusion Data for Computational Modelling and Simulation

    Science.gov (United States)

    Mernagh, T. P.; Bastrakov, E.; Percival, D.; Girvan, S.; Wyborn, L. A.

    2007-12-01

    Accurate constraints on the chemistry of hydrothermal fluids are critical in our capacity to computationally model and simulate how ore deposits form. To maximize results and subsequent interpretation the fluid inclusion populations should be fully characterized using standardised observational and processing techniques. A Virtual Centre for Geofluids and Thermodynamic Data, which includes the fluid inclusion (FIncs) system, has been established to achieve this. The FIncs system is designed to pull together fluid inclusion data from many individual, often disparate studies. The FIncs database and web applications allow researchers to search and retrieve fluid inclusion data and images via a web browser interface. The database will help standardise the way fluid inclusion data and associated metadata are stored. Furthermore, it follows the principles outlined by the Open Geospatial Consortium (OGC) for the Observation and Measurement application schema. It is tightly coupled to enable formalisation of the observations and measurements made on fluid inclusions, and to standardise how these measurements are processed to achieve consistent constraints for geochemical models. FIncs uses both domain factual knowledge and problem-solving knowledge by providing a choice of models (equations of state) for obtaining additional fluid properties via a web-based calculator, which allows researchers to calculate isochoric T&P values and other chemical and physical properties (e.g. salinity, density, etc.). This method has the benefit of ensuring that all derived data are produced and standardised by a selected set of routines. It also enables data from multiple sources to be quickly reprocessed by new routines as they become available and are added to the database toolkit. The database is being developed as an "open" project, which intends to bring together researchers interested in the properties of geological fluids or fluid inclusions. The ultimate goal of the Virtual Centre

  14. Stable isotope signatures of gases liberated from fluid inclusions in bedrock at Olkiluoto

    International Nuclear Information System (INIS)

    Eichinger, F.; Meier, D.; Haemmerli, J.; Diamond, L.

    2010-12-01

    Fluid inclusions in quartzes of the Olkiluoto bedrock contain gaseous N 2 , CO 2 , H 2 , CH 4 , and higher hydrocarbons in varying proportions. Stable carbon and hydrogen isotope signatures of the gas phases give valuable information on their origin and the formation conditions. In previous studies, a method to liberate and quantify the gases trapped in fluid inclusions was developed. It allowed determining the carbon isotope signatures of liberated CO 2 , CH 4 and higher hydrocarbons (HHC), but no hydrogen isotope data were acquired. The method was advanced and, in this study, also stable hydrogen isotopes of CH 4 and H 2 liberated from fluid inclusions could be analysed. The stable carbon signatures of methane and higher hydrocarbons, as well as the hydrogen isotope signatures of methane indicate a predominant thermogenic provenance for those gases. (orig.)

  15. Paleotemperature reconstructions from speleothem fluid inclusions between 14 - 10 ka BP in Milandre cave (NW Switzerland)

    Science.gov (United States)

    Affolter, Stéphane; Häuselmann, Anamaria; Fleitmann, Dominik; Leuenberger, Markus

    2016-04-01

    In cave environments, speleothems constitute a well preserved and precisely dated continental climate archive that record past environmental changes such as paleotemperature or moisture source, namely through oxygen and hydrogen isotopes variations. Fluid inclusions are common in speleothems and they correspond to micrometric voids that often contain fossil liquid water representing past precipitation falling above the cave nearly at the time the inclusions were sealed. To measure the δD and δ18O isotopic composition of speleothem fluid inclusions, we extracted submicrolitre amounts of water from stalagmites (old and recent) coming from Milandre cave (Switzerland) using a new online method developed at the University of Bern (Affolter et al., 2014). The released water is then flushed directly to a Picarro L1102-i or L2140-i laser based instrument that allows to simultaneously monitor hydrogen and oxygen isotopes. At Milandre cave site, a two year isotope monitoring campaign has confirmed that isotopes in precipitation for northwestern Switzerland are principally controlled by air temperature (Affolter et al., 2015). Therefore, when combined with calcite δ18O, the fluid inclusion water isotopes can be used to calculate paleotemperatures. We reconstructed a cold season biased (roughly autumn - winter - spring) paleotemperature trend for the time interval covering the Allerød, the Younger Dryas cold interval and the early Holocene (13'900 - 9'900 BP). References: Affolter S., Fleitmann D., and Leuenberger M.: New online method for water isotope analysis of speleothem fluid inclusions using laser absorption spectroscopy (WS-CRDS), Clim. Past, 10, 1291-1304, doi:10.5194/cp-10-1291-2014, 2014. Affolter S., Häuselmann A.D., Fleitmann D., Häuselmann P., Leuenberger M.: Triple isotope (δD, δ17O, δ18O) study on precipitation, drip water and speleothem fluid inclusions for a Western Central European cave (NW Switzerland), Quat. Sci. Rev., 127, pp. 73-89, 2015.

  16. High-resolution signatures of oxygenation and microbiological activity in speleothem fluid inclusions

    Directory of Open Access Journals (Sweden)

    Nigel J.F. Blamey

    2016-09-01

    Full Text Available Speleothems frequently host “fossil” fluids that were trapped in small inclusions during growth. Such fluids may provide valuable clues to past microbial, geochemical, and climatic processes during their formation. However, one difficulty is to understand which gases represent background atmosphere and fluids within a given cave system at a particular time, and which may be the product of post-trapping residual microbial activity or abiotic chemical reactions? Do we have any hope of sorting out these differences? The success depends on a quantitative understanding of the gas composition trapped in the inclusions and an understanding of the interactions of cave mineralogy, air and water chemistry, and microbiological processes that may interfere with climatic or geochemical interpretations. Our proof-of-concept project uses time synchronous samples from several sites. We report here on this pilot investigation of speleothem inclusions using a methodology for quantitatively analyzing gases dissolved in inclusion fluids. We use incremental crushing of highly spatially resolved samples by mass spectrometry. Here, we report primarily on CH4, CO2, O2, and N2, but have included other detectable gases. The detection limit for He within aqueous fluid inclusions is ~0.2 ppm and gas ratios have ~5% precision using natural standards. We used chemically inert argon as a tracer gas to normalize results to air or air saturated water. This enables interpretation of gas data despite variability in hydrological and geological cave histories. Results are variable. For example, in one case oxygen was depleted while nitrogen was increased, which may be attributable to the breakdown of nitrate or nitrogen-containing biomolecules. In other cases, oxygen is enriched which may be attributed to several factors both geochemical and biological. We suggest potential interpretations between the competing hypotheses with larger future data sets. This first attempt tackles

  17. Fluid inclusions in high-grade metamorphic rocks from S.W. Norway

    NARCIS (Netherlands)

    Swanenberg, H.E.C.

    1980-01-01

    In part one of this thesis, isochoric sections, based on a modified Redl i ch-Kwong equat ion, are presented for the systems C02, C02-N2, N2-CHll and H20-C0 2, This allows the P-T interpretation of fluid inclusion freezing data in terms of the above-mentioned reference systems. Part two deals with

  18. Fluid inclusions in high-grade metamorphic rocks from S.W. Norway

    NARCIS (Netherlands)

    Swanenberg, H.E.C.

    1980-01-01

    In part one of this thesis, isochoric sections, based on a modified Redl i ch-Kwong equat ion, are presented for the systems C02, C02-N2, N2-CHll and H20-C0 2, This allows the P-T interpretation of fluid inclusion freezing data in terms of the above-mentioned reference systems. Part two deals

  19. Composition of fluid inclusions in Permian salt beds, Palo Duro Basin, Texas, U.S.A.

    Science.gov (United States)

    Roedder, E.; d'Angelo, W. M.; Dorrzapf, A.F.; Aruscavage, P. J.

    1987-01-01

    Several methods have been developed and used to extract and chemically analyze the two major types of fluid inclusions in bedded salt from the Palo Duro Basin, Texas. Data on the ratio K: Ca: Mg were obtained on a few of the clouds of tiny inclusions in "chevron" salt, representing the brines from which the salt originally crystallized. Much more complete quantitative data (Na, K, Ca, Mg, Sr, Cl, SO4 and Br) were obtained on ??? 120 individual "large" (mostly ???500 ??m on an edge, i.e., ??? ??? 1.6 ?? 10-4 g) inclusions in recrystallized salt. These latter fluids have a wide range of compositions, even in a given piece of core, indicating that fluids of grossly different composition were present in these salt beds during the several (?) stages of recrystallization. The analytical results indicating very large inter-and intra-sample chemical variation verify the conclusion reached earlier, from petrography and microthermometry, that the inclusion fluids in salt and their solutes are generally polygenetic. The diversity in composition stems from the combination of a variety of sources for the fluids (Permian sea, meteoric, and groundwater, as well as later migrating ground-, formation, or meteoric waters of unknown age), and a variety of subsequent geochemical processes of dissolution, precipitation and rock-water interaction. The compositional data are frequently ambiguous but do provide constraints and may eventually yield a coherent history of the events that produced these beds. Such an understanding of the past history of the evaporite sequence of the Palo Duro Basin should help in predicting the future role of the fluids in the salt if a nuclear waste repository is sited there. ?? 1987.

  20. Reaction Rates Of Olivine Carbonation - An Experimental Study Using Synthetic Fluid Inclusions As Micro-Reactors

    Science.gov (United States)

    Sendula, E.; Lamadrid, H. M.; Bodnar, R. J.

    2017-12-01

    Ultramafic and mafic rocks (e.g. peridotites, serpentinites and basalts) are being considered as possible targets for CO2 sequestration via mineral carbonation. The determination of reaction kinetics and the factors that control mineralization are important in order to understand and predict fluid-rock reactions between the injected CO2 and the host rocks. Here we present results of experiments focused on determining the reaction rates of carbonation of olivine as a function of initial CO2 concentration (20 mol% and 11 mol%) in the aqueous solution and temperature (100°C and 50°C). We used a recently developed experimental method (Lamadrid et al., 2017) that uses synthetic fluid inclusions as micro-reactors. The micro-reactor technique coupled with non-destructive Raman spectroscopy allows us to monitor the reaction progress in situ and in real time, by quantifying the amount of CO2 consumed in the reaction as a function of time. Results show a measurable decrease of CO2 density in the fluid inclusions as a result of the reaction between the CO2-bearing aqueous phase and olivine. Magnesite formation begins within several hours at 100°C and most of the CO2 was consumed within two days. At 50°C, however, magnesite nucleation and precipitation required weeks to months to begin, and the reaction rates were about an order of magnitude slower than in the experiments at 100°C. No significant differences were observed in the reaction rates as a function of initial CO2 concentration. The application of the synthetic fluid inclusion technique as micro-reactors coupled with non-destructive analytical techniques is a promising tool to monitor rates of fluid-rock reactions in situ and in real time, allowing detailed micron-scale investigations. The technique can be applied to a wide variety of chemical systems, host minerals, reaction products, fluid densities, temperatures, and different starting fluid compositions.

  1. Isotope analysis of water trapped in fluid inclusions in deep sea corals

    Science.gov (United States)

    Vonhof, Hubert; Reijmer, John; Feenstra, Eline; Mienis, Furu

    2015-04-01

    Extant Lophelia pertusa deep sea coral specimens from the Loachev mound region in the North Atlantic Ocean contain water filled fluid inclusions in their skeleton. This fluid inclusion water was extracted with a crushing device, and its hydrogen and oxygen isotope ratios analysed. The resulting data span a wide range of isotope values which are remarkably different from the seawater isotope composition of the sites studied. Comparison with food source isotope signatures suggests that coral inclusion water contains a high, but variable proportion of metabolic water. The isotope composition of the inclusion water appears to vary with the position on the deep see coral reef, and shows a correlation with the stable isotope composition of the coral aragonite. This correlation seems to suggest that growth rate and other ecological factors play an important role in determining the isotope composition of fluids trapped in the coral skeleton, which can potentially be developed as a proxy for non-equilibrium isotope fractionation observed in the aragonite skeleton of many of the common deep sea coral species.

  2. Granulites of Bhopalpatnam and Kondagaon belts, Bastar craton, M. P.: petrological and fluid inclusion studies

    Science.gov (United States)

    Prakash Narasimha, K. N.; Janardhan, A. S.; Mishra, V. P.

    The Bhopalpatnam and Kondagaon granulite belts (BGB, KGB) occur surrounding the Bastar craton of central India. This paper deals with the geology, mineralogy and the fluid characteristics of these two belts. The geology of the two belts indicate that they abound in metasedimentary swathes. The metamorphic P-T conditions of the BGB range from 6 to 9 kbar at temperatures of 750°C, whilst those of the KGB vary from 4 to 6 kbar at temperatures of 700°C. The BGB shows an IBC path, while the KGB exhibits a dominant ITD path. These trends, based on mineral chemistry, are corroborated by fluid-inclusion studies. The lithologies of the BGB exhibit high-density CO 2 inclusions that represent the remnants of peak metamorphism. In contrast, the CO 2 inclusions of the KGB are of low density, indicative of post-peak conditions. The studies suggest that the CO 2-rich fluids may not have come from the supracrustal sediments. An external source, possibly underplated basalt, could have supplied the heat and the supercritical fluids. Based on lithological similarities, it can be stated that the BGB is an extension of the late Archaean Karimnagar granulite belt. The important problem which is still to be solved is the junction of the late Archaean BGB with the Eastern Ghats granulite belt.

  3. Comparative Fluid Inclusion Chemistry of Miarolitic Pegmatites from San Diego County, California, USA

    Science.gov (United States)

    Nymberg, D.; Sirbescu, M. L. C.

    2014-12-01

    Miarolitic Li-Cs-Ta pegmatites are an important source of gemstones such as tourmaline var. elbaite and spodumene var. kunzite, but the distribution of gem-bearing pegmatites within a pegmatite field is not understood. This microthermometry, LA-ICP-MS, Raman spectroscopy, and crush-leach study of fluid inclusions in pegmatite quartz aims to discern the chemical variations of late-stage pegmatite fluids in relation to gem mineralization. We studied five mines from three San Diego Co. districts: Chihuahua Valley (C), Jacumba (J), and Pala (P). The ~100 Ma old, 1-10 m thick, subparallel magma sheets intruded plutons of the Peninsular Ranges Batholith or prebatholitic metasediments at an estimated pressure of 200-300 MPa. The pegmatites formed sequentially, from outer zones with comb, layered, and graphic quartz-feldspar textures at the magmatic stage to massive cores and miarolitic pockets at a late, fluid-saturated stage. Pocket quartz was analyzed from pegmatites of variable host rock, magmatic mineral assemblages, and known gem production. The inclusions contained two-phase aqueous fluids and no CO2 or other gases. Fluid salinity ranged from 0.5 to 8.6 wt.% NaCl eq. and correlated positively with inclusion homogenization temperature. Isochoric T at 250 MPa calculated for primary and pseudosecondary inclusions in pocket quartz ranged from 280 to 500 °C in district P, 310-420°C in J, and 230-290°C in C. We attribute the higher T of pocket formation in districts P and J to higher surrounding T at emplacement caused by proximity to other dikes. This preliminary study suggests that gem elbaite and/or kunzite occurrence correlates to Li and B contents in the pocket fluid, which, in turn, are a function of consumption by early, magmatic minerals. The P district has a simple leucogranite mineralogy at the magmatic stage; has as much as 5760 ppm B and 4950 ppm Li in the pocket fluid; and produced both elbaite and kunzite. The J district has abundant magmatic tourmaline

  4. Genetic implications of preliminary mineralogical, paragenetic and fluid inclusion data for the Schwartzwalder uranium mine, Colorado

    International Nuclear Information System (INIS)

    Rich, R.A.; Barabas, A.H.

    1982-01-01

    Epigenetic uranium mineralization at the Schwartzwalder mine occurs in veins and breccia zones associated with Laramide faulting and fracturing in Precambrian metasedimentary rocks. Vein paragenesis consists of three major stages separated by fracturing events: (1) adularia-pitchblende-jordisite-carbonaceous matter; (2) ankerite-marcasite/pyrite-base metal sulphides; and (3) calcite-pyrite. Adularia and possibly jordisite were in part co-deposited with pitchblende. Haematitic alteration haloes are spatially and probably genetically related to stage 1 structures. Fluid inclusions in stage 2 sphalerite and stage 3 calcite are characterized by low filling temperatures (75-165 0 C) and low to intermediate salinity (19 to less than 3 equivalent wt.% NaCl) aqueous solutions. Fluid conclusions in stage 1 adularia and stage 2 ankerite, however, exhibit microthermometry characteristics atypical of aqueous inclusions; crushing-stage work indicates the absence of CO 2 or other gases under pressure in these inclusions. The above observations suggest the following genetic implications: (1) The presence of haematitic alteration haloes about stage 1 structures and the sequence of deposition for vein minerals indicate a trend with time from a relatively oxidizing to a relatively reducing mineralizing fluid and suggest a possible redox mechanism for uranium precipitation; (2) the presence of epigenetic carbonaceous matter in stage 1 structures and fluid inclusion data for minerals deposited before, during and after pitchblende suggest that uranium may have been transported to the site of deposition in a condensed organic or organo-aqueous fluid; (3) the mineralogy, paragenesis and uranium/carbonaceous matter association suggests a striking geochemical similarity between the Schwartzwalder deposit and certain sandstone-type uranium deposits

  5. A new method for synthesizing fluid inclusions in fused silica capillaries containing organic and inorganic material

    Science.gov (United States)

    Chou, I.-Ming; Song, Yucai; Burruss, R. C.

    2008-11-01

    Considerable advances in our understanding of physicochemical properties of geological fluids and their roles in many geological processes have been achieved by the use of synthetic fluid inclusions. We have developed a new method to synthesize fluid inclusions containing organic and inorganic material in fused silica capillary tubing. We have used both round (0.3 mm OD and 0.05 or 0.1 mm ID) and square cross-section tubing (0.3 × 0.3 mm with 0.05 × 0.05 mm or 0.1 × 0.1 mm cavities). For microthermometric measurements in a USGS-type heating-cooling stage, sample capsules must be less than 25 mm in length. The square-sectioned capsules have the advantage of providing images without optical distortion. However, the maximum internal pressure ( P; about 100 MPa at 22 °C) and temperature ( T; about 500 °C) maintained by the square-sectioned capsules are less than those held by the round-sectioned capsules (about 300 MPa at room T, and T up to 650 °C). The fused silica capsules can be applied to a wide range of problems of interest in fluid inclusion and hydrothermal research, such as creating standards for the calibration of thermocouples in heating-cooling stages and frequency shifts in Raman spectrometers. The fused silica capsules can also be used as containers for hydrothermal reactions, especially for organic samples, including individual hydrocarbons, crude oils, and gases, such as cracking of C 18H 38 between 350 and 400 °C, isotopic exchanges between C 18H 38 and D 2O and between C 19D 40 and H 2O at similar temperatures. Results of these types of studies provide information on the kinetics of oil cracking and the changes of oil composition under thermal stress. When compared with synthesis of fluid inclusions formed by healing fractures in quartz or other minerals or by overgrowth of quartz at elevated P- T conditions, the new fused-silica method has the following advantages: (1) it is simple; (2) fluid inclusions without the presence of water can be

  6. Study of fluid inclusions in rodioactive mineralized pegmatites, dara area northern eastern desert, Egypt

    International Nuclear Information System (INIS)

    Ali, B.H.; Abdel Warith, A.

    2003-01-01

    Numerous pegmatite pockets of un zoned and zoned types are the most important rock types from the radioactive point of view. They occur at the marginal parts and higher topographic level of G.Dara younger granites. Zoned pegmatites are composed of extremely coarse-grained milky quartz core, intermediate zone and wall zone. The alteration zone is found at the contact between quartz core and intermediate zone. It is recorded the highest radioactive values due to their mineral composition, as a result of alteration processes associated with radioactive minerals. Only two alteration zones (P1 and P2) has been studied in this paper. The late magmatic alteration process (hematization, kaolinization, chloritization and fluortization) of the pegmatite resulted in the formation of chlorite, fluorite, clay minerals and carbonates (calcite) in the alteration zones as mineral assemblage. opaque minerals are found as pyrite, iron oxyhydroxide and garnet. Fluid inclusion studies by microthermometry were carried out on authigenic minerals (such as quartz and fluorite) in alteration zones (primary fluid inclusions). This study revealed that, at least two stages of the post-magmatic hydrothermal alteration are involved. The first stages of high temperature, low saline fluids are involved. The first stage is of high temperature, low saline fluids which characterized with hematization and/or chloritization resulted from fluid-rock interaction with late magmatic fluids that very probably mixed with external low salinity fluids along brittle structure. The second stage is of low temperature the main role in re high saline fluids characterized the fluoritized alteration due to consequent reaction with wall rocks and mixing with meteoric water. Mixing of low salinity meteoric water with hot a sending saline hydrothermal solution leads to ph change and continuous interaction with wall rock

  7. Lithospheric magma dynamics beneath the El Hierro Volcano, Canary Islands: insights from fluid inclusions

    Science.gov (United States)

    Oglialoro, E.; Frezzotti, M. L.; Ferrando, S.; Tiraboschi, C.; Principe, C.; Groppelli, G.; Villa, I. M.

    2017-10-01

    At active volcanoes, petrological studies have been proven to be a reliable approach in defining the depth conditions of magma transport and storage in both the mantle and the crust. Based on fluid inclusion and mineral geothermobarometry in mantle xenoliths, we propose a model for the magma plumbing system of the Island of El Hierro (Canary Islands). The peridotites studied here were entrained in a lava flow exposed in the El Yulan Valley. These lavas are part of the rift volcanism that occurred on El Hierro at approximately 40-30 ka. The peridotites are spinel lherzolites, harzburgites, and dunites which equilibrated in the shallow mantle at pressures between 1.5 and 2 GPa and at temperatures between 800 and 950 °C (low-temperature peridotites; LT), as well as at higher equilibration temperatures of 900 to 1100 °C (high-temperature peridotites; HT). Microthermometry and Raman analyses of fluid inclusions reveal trapping of two distinct fluid phases: early type I metasomatic CO2-N2 fluids ( X N2 = 0.01-0.18; fluid density (d) = 1.19 g/cm3), coexisting with silicate-carbonate melts in LT peridotites, and late type II pure CO2 fluids in both LT (d = 1.11-1.00 and 0.75-0.65 g/cm3) and HT ( d = 1.04-1.11 and 0.75-0.65 g/cm3) peridotites. While type I fluids represent metasomatic phases in the deep oceanic lithosphere (at depths of 60-65 km) before the onset of magmatic activity, type II CO2 fluids testify to two fluid trapping episodes during the ascent of xenoliths in their host mafic magmas. Identification of magma accumulation zones through interpretation of type II CO2 fluid inclusions and mineral geothermobarometry indicate the presence of a vertically stacked system of interconnected small magma reservoirs in the shallow lithospheric mantle between a depth of 22 and 36 km (or 0.67 to 1 GPa). This magma accumulation region fed a short-lived magma storage region located in the lower oceanic crust at a depth of 10-12 km (or 0.26-0.34 GPa). Following our model

  8. Preliminary results on the petrology and fluid inclusions of the Rossing uraniferous alaskites

    International Nuclear Information System (INIS)

    Cuney, M.

    1980-01-01

    Petrography, radioactivity distribution and fluid inclusions have been studied in three samples of the Rossing alaskites from the S.H. anomaly outside of the Rossing deposit. After the crystallization of the alaskitic magma which involved oligoclase, biotite, orthoclase and quartz, a deuteric alteration produced a quartz, microcline, albite, muscovite, calcite plus minus chlorite mineral association similar to those observed in several French uraniferous granites. Uranium redistribution occurred during this alteration. From fluid inclusions data, the pressure at the time of the intrusion is estimated to have been at least 6kbar for a temperature of 625 degrees Celsius. Reaction of the magma with the marbles of the Rossing formation led to the boiling of the magma by an increase in the CO 2 partial pressure as well as to its crystallization. Immiscibility between a dense saline (more than 30 per cent NaCl) and CO 2 -rich fluid is proposed to have occurred simultaneously or after the fluid oversaturation of the magma. Part of uraninite is formed at the magmatic stage, another part crystallized from the magmatic fluids in the biotite-rich selvages of the alaskites or in the uraninite-fluorite veins. Uraninite crystallization appears to be mainly controlled by the oxygen fugacity prevailing in the magma and in the surrounding rocks

  9. Motions of deformable inclusions in a horizontally oscillating vessel with a compressible fluid

    DEFF Research Database (Denmark)

    Demidov, I.V.; Sorokin, Vladislav

    2016-01-01

    The paper is concerned with the analysis of rigid particle and compressible gas bubble motion in a horizontally oscillating vessel with a compressible fluid. A nonlinear differential equation describing motion of inclusions with respect to the vessel is derived and solved by the method of direct...... of the bubbles which are affected by the negligible vibrational force is found. Also an approximate expression has been obtained for the average velocity of bubble׳s motion in the fluid; relationship between this velocity and bubble radius and vibration parameters has been revealed. A simple physical explanation...

  10. Fluid inclusion and stable isotope study of telluride mineralization at Mahd Adh Dhahab, Saudi Arabia

    Energy Technology Data Exchange (ETDEWEB)

    Afifi, A.M.; Kelly, W.C.

    1985-01-01

    Mahd Adh Dhahab is unique among Precambrian gold deposits in that it displays many characteristics of epithermal precious metal districts. Au-Ag-Cu-Zn-Pb mineralization occurs principally in the third of five generations of quartz veins. Sulfur isotopic equilibrium was generally maintained among sulfides which range in delta/sup 34/S from -1.8 (galena) to 6.4 (pyrite). The narrow range in delta/sup 34/S of sulfides is inconsistent with large variations in f02 calculated from chlorite +/- pyrite +/- hematite assemblages. Galena-sphalerite pairs yield temperatures in the range 160-270/sup 0/C for stage 3 veins, which fall within the 120-300/sup 0/C range defined by fluid inclusion thermometry. Fluid salinities are in the range 0.5 wt.% NaCl equivalent. The trends indicate mixing of delta/sup 18/O approx. = 0 waters with heavier more oxidized waters during stage 4 deposition which led to non-equilibrium oxidation of H/sub 2/S. deltaD values of vein chlorites fall within a narrow range of -65 to -75, while deltaD measurements of inclusion fluids in quartz display a wider spread from -13 to -43; the lighter values may reflect contamination by secondary inclusions. The stable isotope data indicate probable derivation of both sulfur and carbon from igneous sources. District-wide variation in sulfur and oxygen isotopes indicate the presence of several hydrothermal centers, which has possible significance to exploration.

  11. Ancient microbes from halite fluid inclusions: optimized surface sterilization and DNA extraction.

    Directory of Open Access Journals (Sweden)

    Krithivasan Sankaranarayanan

    Full Text Available Fluid inclusions in evaporite minerals (halite, gypsum, etc. potentially preserve genetic records of microbial diversity and changing environmental conditions of Earth's hydrosphere for nearly one billion years. Here we describe a robust protocol for surface sterilization and retrieval of DNA from fluid inclusions in halite that, unlike previously published methods, guarantees removal of potentially contaminating surface-bound DNA. The protocol involves microscopic visualization of cell structures, deliberate surface contamination followed by surface sterilization with acid and bleach washes, and DNA extraction using Amicon centrifugal filters. Methods were verified on halite crystals of four different ages from Saline Valley, California (modern, 36 ka, 64 ka, and 150 ka, with retrieval of algal and archaeal DNA, and characterization of the algal community using ITS1 sequences. The protocol we developed opens up new avenues for study of ancient microbial ecosystems in fluid inclusions, understanding microbial evolution across geological time, and investigating the antiquity of life on earth and other parts of the solar system.

  12. Organic compounds in fluid inclusions of Archean quartz—Analogues of prebiotic chemistry on early Earth

    Science.gov (United States)

    Schreiber, Ulrich; Mayer, Christian; Schmitz, Oliver J.; Rosendahl, Pia; Bronja, Amela; Greule, Markus; Keppler, Frank; Mulder, Ines; Sattler, Tobias; Schöler, Heinz F.

    2017-01-01

    The origin of life is still an unsolved mystery in science. Hypothetically, prebiotic chemistry and the formation of protocells may have evolved in the hydrothermal environment of tectonic fault zones in the upper continental crust, an environment where sensitive molecules are protected against degradation induced e.g. by UV radiation. The composition of fluid inclusions in minerals such as quartz crystals which have grown in this environment during the Archean period might provide important information about the first organic molecules formed by hydrothermal synthesis. Here we present evidence for organic compounds which were preserved in fluid inclusions of Archean quartz minerals from Western Australia. We found a variety of organic compounds such as alkanes, halocarbons, alcohols and aldehydes which unambiguously show that simple and even more complex prebiotic organic molecules have been formed by hydrothermal processes. Stable-isotope analysis confirms that the methane found in the inclusions has most likely been formed from abiotic sources by hydrothermal chemistry. Obviously, the liquid phase in the continental Archean crust provided an interesting choice of functional organic molecules. We conclude that organic substances such as these could have made an important contribution to prebiotic chemistry which might eventually have led to the formation of living cells. PMID:28614348

  13. Organic compounds in fluid inclusions of Archean quartz-Analogues of prebiotic chemistry on early Earth.

    Science.gov (United States)

    Schreiber, Ulrich; Mayer, Christian; Schmitz, Oliver J; Rosendahl, Pia; Bronja, Amela; Greule, Markus; Keppler, Frank; Mulder, Ines; Sattler, Tobias; Schöler, Heinz F

    2017-01-01

    The origin of life is still an unsolved mystery in science. Hypothetically, prebiotic chemistry and the formation of protocells may have evolved in the hydrothermal environment of tectonic fault zones in the upper continental crust, an environment where sensitive molecules are protected against degradation induced e.g. by UV radiation. The composition of fluid inclusions in minerals such as quartz crystals which have grown in this environment during the Archean period might provide important information about the first organic molecules formed by hydrothermal synthesis. Here we present evidence for organic compounds which were preserved in fluid inclusions of Archean quartz minerals from Western Australia. We found a variety of organic compounds such as alkanes, halocarbons, alcohols and aldehydes which unambiguously show that simple and even more complex prebiotic organic molecules have been formed by hydrothermal processes. Stable-isotope analysis confirms that the methane found in the inclusions has most likely been formed from abiotic sources by hydrothermal chemistry. Obviously, the liquid phase in the continental Archean crust provided an interesting choice of functional organic molecules. We conclude that organic substances such as these could have made an important contribution to prebiotic chemistry which might eventually have led to the formation of living cells.

  14. Origin of fluid inclusion water in bedded salt deposits, Palo Duro Basin, Texas

    International Nuclear Information System (INIS)

    Knauth, L.P.; Beeunas, M.A.

    1985-07-01

    Salt horizons in the Palo Duro Basin being considered for repository sites contain fluid inclusions which may represent connate water retained in the salt from the time of original salt deposition and/or external waters which have somehow penetrated the salt. The exact origin of this water is important to the question of whether or not internal portions of the salt deposit have been, and are likely to be, isolated from the hydrosphere for long periods of time. The 18 O/ 16 O and D/H ratios measured for water extracted from solid salt samples show the inclusions to be dissimilar in isotopic composition to meteoric waters and to formation waters above and below the salt. The fluid inclusions cannot be purely external waters which have migrated into the salt. The isotope data are readily explained in terms of mixed meteoric-marine connate evaporite waters which date back to the time of deposition and early diagenesis of the salt (>250 million years). Any later penetration of the salt by meteoric waters has been insufficient to flush out the connate brines

  15. Geology, fluid inclusion and sulphur isotope characteristics of the El Cobre VHMS deposit, Southern Cuba

    Science.gov (United States)

    Cazañas, Xiomara; Alfonso, Pura; Melgarejo, Joan Carles; Proenza, Joaquín Antonio; Fallick, Anthony Edward

    2008-09-01

    The El Cobre deposit is located in eastern Cuba within the volcanosedimentary sequence of the Sierra Maestra Paleogene arc. The deposit is hosted by tholeiitic basalts, andesites and tuffs and comprises thick stratiform barite and anhydrite bodies, three stratabound disseminated up to massive sulphide bodies produced by silicification and sulphidation of limestones or sulphates, an anhydrite stockwork and a siliceous stockwork, grading downwards to quartz veins. Sulphides are mainly pyrite, chalcopyrite and sphalerite; gold occurs in the stratabound ores. Fluid inclusions measured in sphalerite, quartz, anhydrite and calcite show salinities between 2.3 and 5.7 wt% NaCl eq. and homogenisation temperatures between 177 and 300°C. Sulphides from the stratabound mineralisation display δ 34S values of 0‰ to +6.0‰, whilst those from the feeder zone lie between -1.4‰ and +7.3‰. Sulphides show an intra-grain sulphur isotope zonation of about 2‰; usually, δ 34S values increase towards the rims. Sulphate sulphur has δ 34S in the range of +17‰ to +21‰, except two samples with values of +5.9‰ and +7.7‰. Sulphur isotope data indicate that the thermochemical reduction of sulphate from a hydrothermal fluid of seawater origin was the main source of sulphide sulphur and that most of the sulphates precipitated by heating of seawater. The structure of the deposit, mineralogy, fluid inclusion and isotope data suggest that the deposit formed from seawater-derived fluids with probably minor supply of magmatic fluids.

  16. Laser ablation-ICP-AES for the determination of metals in fluid inclusions: An application to the study of magmatic ore fluids

    Science.gov (United States)

    Wilkinson, J. J.; Rankin, A. H.; Mulshaw, S. C.; Nolan, J.; Ramsey, M. H.

    1994-02-01

    The laser ablation-ICP-AES (L-ICP-AES) technique is an effective method for the multielement analysis of individual fluid inclusions. Recent tests on synthetic fluid inclusions and improvements in data processing suggest that the method is valid for the analysis of a range of alkali-, alkali-earth, and transition metals in single, large inclusions (> 30 μm) of moderate to high salinity (>20 wt% NaCl equiv.). The system, involving a small, perspex ablation chamber, a 1 J ruby laser focussed through an optical microscope, and a conventional ICP-AES instrument is discussed and applied to natural fluid inclusions in quartz from two contrasting types of magmatic-hydrothermal mineralization. Samples were selected from the San Pedro Cu-Au porphyry system, New Mexico, USA, and the Sn-W-Cu-mineralized Dartmoor granite of southwest England. Variable salinity, high temperature fluid inclusions in hydrothermal quartz from both environments display similarly high concentrations and ratios of Na, K, Ca, and Fe. The ore metals Cu, Zn, and Mn (but not Sn, Mo, W) were detected in inclusions from both environments. The estimated combined concentrations of up to 3 wt% show that these three elements are major components of these fluids. A method has been devised to estimate the confidence intervals of the measured concentration ratios. The confidence intervals obtained show that the analytical uncertainty for an inclusion is much less than the natural geochemical variation between inclusions so that geologically useful information can be obtained. A trend of increasing salinity with decreasing Na and K and increasing Ca and Fe contents is observed in inclusions from San Pedro, consistent with the continuous evolution of a magmatic aqueous phase exsolved from a low pressure melt during crystallization. In contrast, the combined compositional and microthermometric data for samples from Lee Moor, Dartmoor, suggest that a magmatic aqueous phase evolved from Fe-K-rich to Na

  17. Fluorine concentrations of ore fluids in the Illinois-Kentucky district: Evidence from SEM-EDS analysis of fluid inclusion decrepitates

    Science.gov (United States)

    Kenderes, Stuart M.; Appold, Martin S.

    2017-08-01

    The Illinois-Kentucky district is an atypical occurrence of Mississippi Valley-type (MVT) mineralization that consists predominantly of fluorite rather than metal sulfide minerals. A long-standing assumption for the predominance of fluorite in the Illinois-Kentucky district is that the ore fluids there were anomalously rich in dissolved fluorine compared to typical sedimentary brines and other MVT ore fluids. This hypothesis is based on the unusual close temporal and spatial association of fluorine-rich ultramafic igneous rocks to MVT mineralization in the district, high K and Sr concentrations in the igneous rocks and in MVT ore-hosted fluid inclusions, a significant mantle 3He/4He component in ore-hosted fluid inclusions, and reaction path models that show titration of a HF-rich fluid into sedimentary brine is capable of producing a fluorite-dominated MVT ore mineral assemblage. The purpose of the present study was to test this hypothesis more directly by determining the fluorine concentration of the Illinois-Kentucky ore fluid through SEM-EDS analysis of evaporative solute mounds resulting from thermal decrepitation of fluid inclusions hosted in sphalerite. All 26 evaporative solute mounds from Illinois-Kentucky sphalerite samples analyzed contained detectable concentrations of fluorine of 1-4 weight percent. Based on calibration to standard solutions and previously published fluid inclusion major element concentrations, these solute mound fluorine concentrations correspond to fluid inclusion fluorine concentrations of about 680-4300 ppm, indicating that the Illinois-Kentucky ore fluids were quite rich in fluorine compared to typical sedimentary brines, which have fluorine concentrations mainly on the order of 1's to 10's of ppm. In contrast, solute mounds from sphalerite-hosted fluid inclusions from the Tri-State district did not contain fluorine in excess of the detection limit. The detection limit equates to an aqueous fluorine concentration between 87 and

  18. Annular fluid inclusions from a quartz vein intercalated with metapelites from the Besshi area of the Sanbagawa belt, SW Japan

    Science.gov (United States)

    Yoshida, Kenta; Hirajima, Takao

    Annular fluid inclusions were found in a foliation-parallel quartz vein intercalated with metapelites from the Besshi area of the Sanbagawa belt, SW Japan. The preserved “foam microstructure” of the quartz vein suggests low differential stress at high temperatures for its formation. Three types of fluid inclusions have been identified: the earliest one, FIA-I, is characterized by two phase inclusions arranged along intragranular planes and mainly composed of aqueous saline fluid and CH4 gas; FIA-II texturally comparable to FIA-I consists of CH4-N2-CO2-H2 gas phase inclusions with rare two-phase inclusions; the latest type, FIA-III, is characterized by arrangements along transgranular planes consisting of two-phase inclusions mainly composed of CH4-N2 vapor in aqueous saline fluid. Amongst them, FIA-I contains annular fluid inclusions, which are attributed to reequilibration due to a confining pressure increase, suggesting that the host rock underwent the compression after the entrapment of FIA-I. Textural observations and chemical characteristics show that FIA-I and -II were trapped during prograde or near the peak metamorphic stage, and that FIA-III was probably trapped at an early stage of the exhumation.

  19. Fluid Inclusion Study of Quartz Xenocrysts in Mafic Dykes from Kawant Area, Chhota Udaipur District, Gujarat, India

    Directory of Open Access Journals (Sweden)

    Randive Kirtikumar

    2015-09-01

    Full Text Available Unusual mafic dykes occur in the proximity of the Ambadongar Carbonatite Complex, Lower Narmada Valley, Gujarat, India. The dykes contain dense population of quartz xenocrysts within the basaltic matrix metasomatised by carbonate-rich fluids. Plagioclase feldspars, relict pyroxenes, chlorite, barite, rutile, magnetite, Fe-Ti oxides and glass were identified in the basaltic matrix. Quartz xenocrysts occur in various shapes and sizes and form an intricate growth pattern with carbonates. The xenocrysts are fractured and contain several types of primary and secondary, single phase and two-phase fluid inclusions. The two-phase inclusions are dominated by aqueous liquid, whereas the monophase inclusions are composed of carbonic gas and the aqueous inclusions homogenize to liquid between 226°C and 361°C. Majority of the inclusions are secondary in origin and are therefore unrelated to the crystallization of quartz. Moreover, the inclusions have mixed carbonic-aqueous compositions that inhibit their direct correlation with the crustal or mantle fluids. The composition of dilute CO2-rich fluids observed in the quartz xenocrysts appear similar to those exsolved during the final stages of evolution of the Amba Dongar carbonatites. However, the carbonates are devoid of fluid inclusions and therefore their genetic relation with the quartz xenocrysts cannot be established.

  20. C-O-H-S magmatic fluid system in shrinkage bubbles of melt inclusions

    Science.gov (United States)

    Robidoux, P.; Frezzotti, M. L.; Hauri, E. H.; Aiuppa, A.

    2016-12-01

    Magmatic volatiles include multiple phases in the C-O-H-S system of shrinkage bubbles for which a conceptual model is still unclear during melt inclusion formation [1,2,3,4]. The present study aims to qualitatively explore the evolution of the volatile migration, during and after the formation of the shrinkage bubble in melt inclusions trapped by olivines from Holocene to present at San Cristóbal volcano (Nicaragua), Central American Volcanic Arc (CAVA). Combined scanning electron microscope (SEM) and Raman spectroscopy observations allow to define the mineral-fluid phases inside typical shrinkage bubbles at ambient temperature. The existence of residual liquid water is demonstrated in the shrinkage bubbles of naturally quenched melt inclusion and this water could represents the principal agent for chemical reactions with other dissolved ionic species (SO42-, CO32-, etc.) and major elements (Mg, Fe, Cu, etc.) [4,5]. With the objective of following the cooling story of the bubble-inclusion system, the new methodological approach here estimate the interval of equilibrium temperatures for each SEM-Raman identified mineral phase (carbonates, hydrous carbonates, sulfurs, sulfates, etc.). Finally, two distinct mechanisms are proposed to describe the evolution of this heterogeneous fluid system in bubble samples at San Cristóbal which imply a close re-examination for similar volcanoes in subduction zone settings: (1) bubbles are already contracted and filled by volatiles by diffusion processes from the glass and leading to a C-O-H-S fluid-glass reaction enriched in Mg-Fe-Cu elements (2) bubbles are formed by oversaturation of the volatiles from the magma which is producing an immiscible metal-rich fluid. [1]Moore et al. (2015). Am. Mineral. 100, 806-823 [2]Wallace et al. (2015). Am. Mineral. 100, 787-794 [3]Lowenstern (2015). Am. Mineral. 100, 672-673 [4]Esposito, et al. (2016). Am. Mineral. 101, 1691-1708 [5]Kamenetsky et al. (2001). Earth Planet. Sci. Lett. 184, 685-702

  1. Acidophilic Halophilic Microorganisms in Fluid Inclusions in Halite from Lake Magic, Western Australia

    OpenAIRE

    Conner, Amber J.; Benison, Kathleen C.

    2013-01-01

    Lake Magic is one of the most extreme of hundreds of ephemeral acid-saline lakes in southern Western Australia. It has pH as low as 1.7, salinity as high as 32% total dissolved solids, temperatures ranging from 0°C to 50°C, and an unusually complex aqueous composition. Optical petrography, UV-vis petrography, and laser Raman spectrometry were used to detect microorganisms and organic compounds within primary fluid inclusions in modern bedded halite from Lake Magic. Rare prokaryotes appear as ...

  2. Sr isotope geochemistry of East Alpine mineral deposits and mass spectrometric analyses of fluid inclusions

    International Nuclear Information System (INIS)

    Grum, W.

    1995-05-01

    Strontium isotope geochemistry and deformational history of selected carbonate-hosted deposits from different tectonic positions in the Eastern Alps were studied. In this context an equipment has been constructed to analyze the composition of volatile components of fluid inclusions (FI). Based on the results of Sr-isotopic investigations two groups of deposits are discriminated: Deposits formed by formation waters and/or metamorphogenic fluids: Tux (magnesite, scheelite), Otterzug (barite), Lassing (magnesite), Rabenwald (talc), Laussa and Mooseck (fluorite). The mineralizing fluids are derived from different sedimentary rock series and therefore 87 Sr/ 86 Sr-ratios vary between 0.707 and 0.719. Deposits situated along fault zones: Lassing (talc), Gasteiner Tal (Silberpfennig area; gold), Schlaining (stibnite) and Waldenstein (specularite). Sr isotope ratios of the mineralizing fluids from Lassing, Waldenstein and Schlaining ranges from 0.7112 to 0.7127 and are therefore thought to have scavenged the East Alpine crystalline. The mineralizing solutions of the Gasteiner Tal deposit may either have equilibrated with low radiogenic sedimentary or with (ultra-)basic rocks. A cracking chamber has been constructed in order to open FI by cracking for mass spectrometric analysis of volatile components. Gases are analysed using a quadrupole mass spectrometer. The desorption of gas from metal and sample surfaces during cracking can be neglected. The amount of gas released from the mineral lattices was studied. With that fast method ore bearing from barren host rocks have been distinguished by different composition of the FI at the Brixlegg barite mineralization (Eastern Alps). Within the Galway fluorite deposit (Ireland) different fluids were involved and mass spectrometric analysis were carried out to characterize these different fluids and to identify their origin. (author)

  3. Modeling on Fluid Flow and Inclusion Motion in Centrifugal Continuous Casting Strands

    Science.gov (United States)

    Wang, Qiangqiang; Zhang, Lifeng; Sridhar, Seetharaman

    2016-08-01

    During the centrifugal continuous casting process, unreasonable casting parameters can cause violent level fluctuation, serious gas entrainment, and formation of frozen shell pieces at the meniscus. Thus, in the current study, a three-dimensional multiphase turbulent model was established to study the transport phenomena during centrifugal continuous casting process. The effects of nozzle position, casting and rotational speed on the flow pattern, centrifugal force acting on the molten steel, level fluctuation, gas entrainment, shear stress on mold wall, and motion of inclusions during centrifugal continuous casting process were investigated. Volume of Fluid model was used to simulate the molten steel-air two-phase. The level fluctuation and the gas entrainment during casting were calculated by user-developed subroutines. The trajectory of inclusions in the rotating system was calculated using the Lagrangian approach. The results show that during centrifugal continuous casting, a large amount of gas was entrained into the molten steel, and broken into bubbles of various sizes. The greater the distance to the mold wall, the smaller the centrifugal force. Rotation speed had the most important influence on the centrifugal force distribution at the side region. Angular moving angle of the nozzle with 8° and keeping the rotation speed with 60 revolutions per minute can somehow stabilize the level fluctuation. The increase of angular angle of nozzle from 8 to 18 deg and rotation speed from 40 to 80 revolutions per minute favored to decrease the total volume of entrained bubbles, while the increase of distance of nozzle moving left and casting speed had reverse effects. The trajectories of inclusions in the mold were irregular, and then rotated along the strand length. After penetrating a certain distance, the inclusions gradually moved to the center of billet and gathered there. More work, such as the heat transfer, the solidification, and the inclusions entrapment

  4. Fluid Inclusion Analysis of other Host Minerals besides Quartz: Application to Granite-Related Quartz-Topaz Veins and Garnet Skarns in Porphyry Copper-Gold Ore Systems

    OpenAIRE

    Schlöglova, Katerina

    2018-01-01

    Fluid inclusions are the only available samples of paleo-fluids responsible for crystallization of hydrothermal minerals including ore phases. Analysis of fluid inclusions implicitly assumes that the inclusions have preserved their chemical composition since the time of their entrapment. There is, however, an increasing evidence from experimental work and analytical studies of natural samples showing that inclusions hosted in quartz – a ubiquitous host in many ore-forming systems – can experi...

  5. The Use of Integrated Fluid Inclusion Studies for Constraining Petroleum Charge History at Parsons Pond, Western Newfoundland, Canada

    Directory of Open Access Journals (Sweden)

    James Conliffe

    2017-03-01

    Full Text Available This study, based on fluid inclusion petrography, microthermometry and ultraviolet microspectroscopy of inclusion oil, investigates the petroleum charge history at Parsons Pond, western Newfoundland. To address this matter, drill core and cuttings samples of allochthonous and autochthonous strata in the Parson’s Pond area were collected from three exploration wells. Fluid inclusions were examined from fragments of calcite and quartz veins, diagenetic cements in sandstone, and in large hydrothermal dolomite and calcite crystals. Primary aqueous inclusions in authigenic sandstone cements indicate that cementation occurred at relatively shallow depths and low temperatures (<50 °C. Hydrocarbon-bearing fluid inclusions (petroleum, wet gas and gas are generally restricted to calcite and quartz veins, indicating that petroleum and gas migration at Parson’s Pond is fracture-controlled. No hydrocarbons were observed in the diagenetic cements of the essentially tight sandstones. Fluid inclusion microthermometry and ultraviolet microspectroscopy indicate the presence of multiple generations of hydrocarbon fluid, ranging in composition from ~33 API gravity petroleum to pure CH4. Petrographic evidence suggests that hydrocarbons were generated multiple times during progressive burial and heating. In addition, the distribution of hydrocarbon bearing inclusions with depth suggests that deeper levels are gas-prone, with petroleum confined to relatively shallow depths. Although only gas flow was encountered during the drilling of exploration wells at Parson’s Pond, the presence of petroleum-bearing fluid inclusions in calcite and quartz veins indicates that the historical production from shallow wells in the Parsons Pond area likely tapped small reservoirs of fractured petroliferous strata.

  6. Final state effects in inclusive quasielastic electron scattering from nuclei: Clues from quantum fluids

    International Nuclear Information System (INIS)

    Silver, R.N.; Clark, J.W.

    1988-01-01

    The impulse approximation (IA) predicts that momentum distributions, n/sub k/, in many-body systems should be measurable by inclusive quasielastic scattering at high energy and momentum (w,Q) transfer. The observations that the cross section appears to satisfy ''Y-scaling'' (i.e., is a function not of both w and Q of a single variable, Y) is usually taken as a signature of the IA. In nuclear physics, inelastic electron scattering at GeV energies should reveal the high momentum components of the nuclear wave function. In quantum fluids, neutron scattering at hundreds of MeV energies should measure the Bose condensate in superfluid /sup 4/He and the Fermi surface discontinuity and depletion of the Fermi sea in /sup 3/He. In molecular and condensed matter systems, X-ray Compton scattering at keV energies reveals electronic n/sub k/. Such experiments test many-body wave functions calculated by methods such as Green Function and Path Integral Monte Carlo, and Fermi Hypernetted Chain. However, an outstanding issue has been the corrections to the IA due to the scattering of the recoiling particle from neighboring particles, which are termed ''final state effects'' (FSE). The FSE should be especially important in nuclei and quantum fluids where the potentials have steeply repulsive cores. While there have been a variety of theories proposed for FSE, until now none has been adequately tested by experiment. Recently, the ''hard core perturbation theory'' (HCPT) for FSE in quantum fluids by Silver has been successfully compared to new neutron scattering measurements on /sup 4/He by P. E. Sokol and colleagues. In this paper, we shall discuss the lessons of this success for the extraction of n/sub k/ in nuclei by inclusive ''quasielastic electron-nucleus scattering'' (QENS). 19 refs., 12 figs

  7. Stable isotope composition of fluid inclusions preserved in halite derived from Wieliczka and Bochnia beds (southern Poland)

    International Nuclear Information System (INIS)

    Dulinski, M.; Rozanski, K.; Alexandrowicz, Z.; Chmura, A.

    1999-01-01

    Halite deposits located in the southern Poland, near Krakow, are famous mostly due to medieval salt mine located in Wieliczka. Contrary to most salt deposits in Europe forming large domes, the halite deposits near Krakow form distinct beds, extending from west to east on the area of ca. 10 km 2 , with several types of salt identified. The deposits were formed in Miocene, ca. 15 mln years ago. Stable isotope composition of fluid inclusions trapped in the halite crystals originating from Wieliczka and Bochnia salt mines was investigated. Two distinct groups of samples were analyzed: (i) samples derived from so-called 'green salt' beds forming extensive horizontal structures, and (ii) large monocrystals of halite collected in crystal caves which form a part of the tourist tract within the Wieliczka Salt Mine. The samples belonging to the first group were heated under vacuum to extract the fluid inclusions, according to the procedure developed in our laboratory and used previously to extract inclusions from speleothem samples. The macro-inclusions present in some monocrystals of halite collected in crystal caves were removed or analysis without any thermal treatment. The concentration of bivalent cations (Ca 2+ , Mg 2- was measured in the bulk material and in fluid inclusions (only second group). The 2 H and 18 O isotope composition of fluid inclusions extracted from halite samples was measured

  8. Au-bearing magnetite mineralizaion in Kashmar (alteration, mineralization, geochemistry, geochemistry and fluid inclusions;

    Directory of Open Access Journals (Sweden)

    Alireza Almasi

    2017-02-01

    Full Text Available Introduction The study area is located in the central part of the Khaf- Kashmar- Bardaskan volcano-plotunic belt (briefly KKBB. Several IOCG deposits such as Tanourjeh Au-bearing magnetite deposit and Kuh-e-Zar Specularite-rich Au deposit have been explored in KKBB. Geology, alteration, mineralization, geochemistry and fluid inclusion results in Kashmar suggest the IOCG type Au-bearing magnetite mineralization. These IOCG deposits at KKBB form at an active continental arc related to SSZ-type Sabzevar oceanic subduction. Materials and methods Use of Landsat 7+, IRS and Aster satellites. Petrography and alteration Studies in 150 thin sections of volcanic and intrusive rocks. Sampling of ore-bearing quartz vein and mineralography. Preparation of 28 geochemistry samples by the chip composite method of ore-bearing quartz vein and analyzing them in the ACME laboratory by Aqua Regia 1DX1. Fluid inclusions studies of 14 samples of quartz and barite related to the ore minerals of ore-bearing quartz vein by THM600 stage of Linkam company. Results Magmatic events in Kashmar occur at Paleocene-Eocene and include: (1 old mafic - intermediate volcano-plutonic series; (2 felsic volcanic and granitoids; and (3 parallel swarm dykes which are youngest (Almasi et al., 2016. Geochemically, Kashmar rocks are metaluminous to highly peraluminous and Tholeitic to calc-alkaline and shoshonitic in composition (Almasi et al., 2016. The field characteristics, together with isotope and geochemical analyses show that all rock types are essentially co-magmatic and post-collisional I-type (Almasi et al., 2016. Alteration of Kashmar is described in two ways: (1 intense ellipsoidal-linear Argillic-Sillicification and low sericitic with Silica caps and with medium widespread and propylitic alterations in triple regions, next to Dorouneh fault; and (2 Medium Hematite-Carbonate-Chlorite-Silicification alterations in Kamarmard heights. In parts of near the Doruneh fault, sometimes

  9. Pressure-temperature-fluid constraints for the Emmaville-Torrington emerald deposit, New South Wales, Australia: Fluid inclusion and stable isotope studies

    Science.gov (United States)

    Loughrey, Lara; Marshall, Dan; Jones, Peter; Millsteed, Paul; Main, Arthur

    2012-06-01

    The Emmaville-Torrington emeralds were first discovered in 1890 in quartz veins hosted within a Permian metasedimentary sequence, consisting of meta-siltstones, slates and quartzites intruded by pegmatite and aplite veins from the Moule Granite. The emerald deposit genesis is consistent with a typical granite-related emerald vein system. Emeralds from these veins display colour zonation alternating between emerald and clear beryl. Two fluid inclusion types are identified: three-phase (brine+vapour+halite) and two-phase (vapour+liquid) fluid inclusions. Fluid inclusion studies indicate the emeralds were precipitated from saline fluids ranging from approximately 33 mass percent NaCl equivalent. Formational pressures and temperatures of 350 to 400 °C and approximately 150 to 250 bars were derived from fluid inclusion and petrographic studies that also indicate emerald and beryl precipitation respectively from the liquid and vapour portions of a two-phase (boiling) system. The distinct colour zonations observed in the emerald from these deposits is the first recorded emerald locality which shows evidence of colour variation as a function of boiling. The primary three-phase and primary two-phase FITs are consistent with alternating chromium-rich `striped' colour banding. Alternating emerald zones with colourless beryl are due to chromium and vanadium partitioning in the liquid portion of the boiling system. The chemical variations observed at Emmaville-Torrington are similar to other colour zoned emeralds from other localities worldwide likely precipitated from a boiling system as well.

  10. Chemical and textural characteristics of multistage fluid inclusions with high Li/B ratio found from the Sanbagawa belt.

    Science.gov (United States)

    Yoshida, K.; Hirajima, T.

    2012-04-01

    Recent studies invoked that the variation of peculiar fluid soluble light elements, such as Li, B and Cl, are capable of suggesting generation depths of fluid released in subduction zones (e.g., Scambelluri et al., 2004; Bebout et al., 2007; Marschall et al., 2009). Crush-leached fluids extracted from quartz veins intercalated with metabasites of the Sanbagawa metamorphic belt show high Li and B concentrations, whose Li/B ratios show a positive correlation with metamorphic grade of the host rocks, i.e., from 0.02 for pumpellyite-actinolite facies to 0.27 for eclogite facies (Sengen et al., 2009). Furthermore, crush-leached fluids extracted from quartz veins intercalated with metasediments in proximal to the eclogite unit in the Besshi district show much higher Li/B ratio (ca. 0.36-1.99). Yoshida et al. (2011) pointed out that Li/B ratio of dehydrated fluids was controlled by the rock types of the host rocks, i.e., Li/B ratio of dehydrated fluids derived from tourmaline-free metasediments show much higher values than those expected from metabasites. Those obtained data suggest that the Li/B ratio of the deep fluid has a potential as a depth indicator but there remain many unknown factors for establishing it. The Li/B ratio of extracted fluid obtained by the crush-leached method integrates the whole fluid activities which the host rocks were taken place. To investigate the fluid activity history for the sample showing the highest Li/B ratio (1.99), detailed petrographical and microthemometric studies were performed. The studied sample IR04 is a foliation-parallel quartz vein intercalated with a Grt-Hbl-Ph schist probably derived from clay, whose peak P-T conditions are estimated as 600 °C and 1.3 GPa using pseudosection analysis. The quartz vein shows a foam microstructure, suggesting that low differential stress and high-T conditions were attained during its texture formation. Three types of fluid inclusions have been identified: the earliest one, FIA-I, is

  11. A Fluid Inclusion Study of the Brookbank Deposit, Northwestern Ontario: A Transition from Mesothermal to Epithermal Gold Deposition

    Directory of Open Access Journals (Sweden)

    Barbara Kowalski

    2018-03-01

    Full Text Available The Brookbank and Cherbourg Zone gold deposits are located in the Beardmore–Geraldton greenstone belt of the Wabigoon Subprovince of the Archean Superior Province of the Canadian Shield. Brookbank is a shear zone deposit, whereas the Cherbourg Zone, joined by a shear zone to the Brookbank, is a fissure vein deposit, presumably formed by the same ore-depositing fluid. A total of 375 fluid inclusions, all with low salinity (generally <1 °C freezing point depression and presence of CO2, from the two deposits were studied. Cross-cutting relationships delineated three stages of vein formation: (1 pre-ore, (2 ore stage and (3 post-ore. Stage 1 inclusions homogenized at ca. 230 °C with low salinity, although at Brookbank a high temperature episode at ca. 360 °C was noted. Stage 2 homogenized at ca. 266 °C at the Cherbourg Zone and over a range 258–269 °C with somewhat higher salinity. Eutectic temperatures indicate that the fluid composition was within the MgCl2-NaCl-H2O system. Fluid immiscibility was prominent in that inclusions homogenized to liquid and vapor at the same temperature were observed. The majority of inclusions from Brookbank homogenized to vapor, whereas those from the Cherbourg Zone homogenized to liquid, marking the transition from mesothermal to epithermal lode gold deposition. Stage 3 fluid inclusions from the Cherbourg Zone homogenized at slightly elevated temperatures and contained fluid possibly representing metastable hydrates of KCl. These post-ore fluids may have been the source of potassium feldspar alteration that overprinted earlier alteration assemblages.

  12. Raman spectroscopy of organic, solid and fluid inclusions in the Oldest Halite of LGOM area (SW Poland)

    Science.gov (United States)

    Toboła, Tomasz

    2018-01-01

    Raman spectroscopy was applied to determine the degree of recrystallization and the influence of the secondary solution migration on the Oldest Halite (Na1) in Lubin-Głogów Copper District (LGOM). Numerous organic matter (OM) inclusions which generally show weak structural ordering was found in halite crystals. In this context they are similar to solid bitumens or carbonaceous matter of low thermal alteration. The difference in the Raman line-shape of OM indicated various thermal alteration of salt from the Oldest Halite formation due to hot fluid flow. Solutions included in the secondary fluid inclusions often contain dissolved gases such as CH4, N2, H2S. The presence of these gases is connected with migration process from basement to the salt formation. Moissanite in fluid inclusions was accidentally trapped during inclusion formation, i.e. is not a daughter mineral. It was also found in the halite as an individual solid inclusions as well as in the anhydrite concentrations. Raman spectroscopy allowed to determine also such solid inclusions in halite as celestine, magnesite, pyrite, lepidocrocite and goethite as well as hydrocarbons.

  13. In situ quantification of Br and Cl in minerals and fluid inclusions by LA-ICP-MS: a powerful tool to identify fluid sources

    Science.gov (United States)

    Hammerli, Johannes; Rusk, Brian; Spandler, Carl; Emsbo, Poul; Oliver, Nicholas H.S.

    2013-01-01

    Bromine and chlorine are important halogens for fluid source identification in the Earth's crust, but until recently we lacked routine analytical techniques to determine the concentration of these elements in situ on a micrometer scale in minerals and fluid inclusions. In this study, we evaluate the potential of in situ Cl and Br measurements by LA-ICP-MS through analysis of a range of scapolite grains with known Cl and Br concentrations. We assess the effects of varying spot sizes, variable plasma energy and resolve the contribution of polyatomic interferences on Br measurements. Using well-characterised natural scapolite standards, we show that LA-ICP-MS analysis allows measurement of Br and Cl concentrations in scapolite, and fluid inclusions as small as 16 μm in diameter and potentially in sodalite and a variety of other minerals, such as apatite, biotite, and amphibole. As a demonstration of the accuracy and potential of Cl and Br analyses by LA-ICP-MS, we analysed natural fluid inclusions hosted in sphalerite and compared them to crush and leach ion chromatography Cl/Br analyses. Limit of detection for Br is ~8 μg g−1, whereas relatively high Cl concentrations (> 500 μg g−1) are required for quantification by LA-ICP-MS. In general, our LA-ICP-MS fluid inclusion results agree well with ion chromatography (IC) data. Additionally, combined cathodoluminescence and LA-ICP-MS analyses on natural scapolites within a well-studied regional metamorphic suite in South Australia demonstrate that Cl and Br can be quantified with a ~25 μm resolution in natural minerals. This technique can be applied to resolve a range of hydrothermal geology problems, including determining the origins of ore forming brines and ore deposition processes, mapping metamorphic and hydrothermal fluid provinces and pathways, and constraining the effects of fluid–rock reactions and fluid mixing.

  14. Characterization of fluid inclusions and sulfur isotopes in the Iju porphyry copper deposit, North West of Shahr-e-Babak

    Directory of Open Access Journals (Sweden)

    Malihe Golestani

    2017-07-01

    Full Text Available Introduction The Iju porphyry copper deposit is located in the southern part of the Urumieh-Dokhtar magmatic arc (Dehaj-Sarduieh belt within the Kerman copper belt (Dimitrijevic, 1973. The Porphyry Copper mineralization in the Iranian plate occurs dominantly along the Urumieh-Dokhtar arc, which has resulted from the subduction of the Arabian plate beneath the central Iran and the closure of the Neo-Tethys Ocean during the Alpine orogeny (Hassanzadeh, 1993. The Iju porphyry copper deposit with 25 million tons of ore reserves is one of the main copper deposits within the Kerman copper belt. The mining area is composed of upper Miocene volcanic and subvolcanic rocks (mineralized and barren subvolcanic rocks and quaternary deposits. Two hydrothermal alteration zones of quartz-sericite-pyrite and propylitic zones can be identified in the Iju area. The copper mineralization in the Iju deposit occurs as disseminated, stockwork and hydrothermal breccia. In the hypogene zone, the mineral paragenesis include chalcopyrite, pyrite, with minor occurrences of bornite and magnetite. This paper reports geological, mineralogical, fluid inclusion and S isotope data from the Iju deposit in order to investigate ore-bearing fluids’ characteristics and the mechanisms of ore deposition. Materials and methods Fifteen samples of syngenetic quartz+pyrite bearing veinlets within the quartz-sericite-pyrite zone were selected from different depths across the seven boreholes. Quartz was used for double-polished thin sections and pyrite was used for sulfur isotope analysis. Fluid inclusion studies were performed using the Linkam cooling and heating stage, the THMSG 600 model. The syngenetic pyrite with thermometry quartz sample was used for the sulfur isotope experiments. Stable isotope analysis was performed at the Hatch Stable Isotope Laboratory in the University of Ottawa, Canada. Results The fluid inclusions of the Iju deposit represent a wide range in the

  15. Fluid inclusions of the Horní Slavkov Sn-W ore deposit, Bohemian Massif, Czech Republic: evidence for non-magmatic source of greisenizing fluids?

    Czech Academy of Sciences Publication Activity Database

    Dolníček, Z.; René, Miloš; Prochaska, W.

    2011-01-01

    Roč. 87, - (2011), s. 68-69 ISSN 1017-8880. [Ecrofi XXI. 09.08.2011-11.08.2011, Leoben] R&D Projects: GA ČR GA205/09/0540 Institutional research plan: CEZ:AV0Z30460519 Keywords : fluid inclusion * greisen * tin ore Subject RIV: DB - Geology ; Mineralogy

  16. Geochemical Signature of Magmatic-Hydrothermal Fluids Exsolved from the Beauvoir Rare-Metal Granite (Massif Central, France: Insights from LA-ICPMS Analysis of Primary Fluid Inclusions

    Directory of Open Access Journals (Sweden)

    Matthieu Harlaux

    2017-01-01

    Full Text Available The Beauvoir granite (Massif Central, France represents an exceptional case in the European Variscan belt of a peraluminous rare-metal granite crosscutting an early W stockwork. The latter was strongly overprinted by rare-metal magmatic-hydrothermal fluids derived from the Beauvoir granite, resulting in a massive topazification of the quartz-ferberite vein system. This work presents a complete study of primary fluid inclusions hosted in quartz and topaz from the Beauvoir granite and the metasomatized stockwork, in order to characterize the geochemical composition of the magmatic fluids exsolved during the crystallization of this evolved rare-metal peraluminous granite. Microthermometric and Raman spectrometry data show that the earliest fluid (L1 is of high temperature (500 to >600°C, high salinity (17–28 wt.% NaCl eq, and Li-rich (Te100 m and interaction with external fluids.

  17. Solubility of gold in oxidized, sulfur-bearing fluids at 500-850 °C and 200-230 MPa: A synthetic fluid inclusion study

    Science.gov (United States)

    Guo, Haihao; Audétat, Andreas; Dolejš, David

    2018-02-01

    Although Au solubility in magmatic-hydrothermal fluids has been investigated by numerous previous studies, there is a dearth of data on oxidized (log fO2 > FMQ+2.5; FMQ - fayalite-magnetite-quartz buffer), sulfur-bearing fluids such as those that formed porphyry Cu-Au (-Mo) deposits. We performed experiments to constrain the effects of fluid salinity, HCl content, sulfur content, fO2 and temperature on Au solubility in such oxidized, sulfur-bearing fluids. For this purpose, small aliquots of fluids equilibrated with Au metal were trapped at high pressure and temperature in the form of synthetic fluid inclusions in quartz and were subsequently analyzed by LA-ICP-MS. Additionally, Raman spectra were collected from quartz-hosted fluid inclusions at up to 600 °C to help to identify the nature of dissolved gold and sulfur species. Gold solubility was found to be affected most strongly by the HCl content of the fluid, followed by fO2, fluid salinity and temperature. Compared to these factors the sulfur content of the fluid has relatively little influence. At 600 °C and 100 MPa, fluids with geologically realistic HCl contents (∼1.1 wt%) and salinities (7-50 wt% NaClequiv) dissolve ∼1000-3000 ppm Au at oxygen fugacities controlled by the magnetite-hematite buffer. At even more oxidized conditions (three log units above the hematite-magnetite fO2 buffer), HCl-, NaCl- and H2SO4-rich fluids can dissolve up to 5 wt% Au at 800 °C and 200 MPa. The observed Au solubility trends are controlled by HCl0 species in the Na-H-Cl-SO4 fluid and are quantitatively reproduced by existing thermodynamic data for Au-Cl complexes. In all experiments, AuCl0 and AuCl2- species are predicted to occur in comparable although variable concentrations, and account for more than 95% of Au solutes. Natural, high-temperature (>500 °C) brine inclusions from porphyry Cu-Au (-Mo) deposits contain significantly less Au than gold-saturated brines that were synthesized experimentally, implying that the

  18. Petrology, isotopic and fluid inclusion studies of eclogites from Sujiahe, NW Dabie Shan (China), July 1 2002

    NARCIS (Netherlands)

    Fu, B.; Zheng, Y.-F.; Touret, J.L.R.

    2002-01-01

    In addition to the Triassic Hong'an low-T-high-P eclogite and the Xinxian coesite-bearing kyanite-glaucophane eclogite, Silurian coesite-free amphibole eclogites occur in the Sujiahe region, NW Dabie Shan of central China. A comprehensive study of petrology, Nd-Sr, O-H isotopes and fluid inclusions

  19. Volcanic stratigraphy: A review

    Science.gov (United States)

    Martí, Joan; Groppelli, Gianluca; Brum da Silveira, Antonio

    2018-05-01

    Volcanic stratigraphy is a fundamental component of geological mapping in volcanic areas as it yields the basic criteria and essential data for identifying the spatial and temporal relationships between volcanic products and intra/inter-eruptive processes (earth-surface, tectonic and climatic), which in turn provides greater understanding of the geological evolution of a region. Establishing precise stratigraphic relationships in volcanic successions is not only essential for understanding the past behaviour of volcanoes and for predicting how they might behave in the future, but is also critical for establishing guidelines for exploring economic and energy resources associated with volcanic systems or for reconstructing the evolution of sedimentary basins in which volcanism has played a significant role. Like classical stratigraphy, volcanic stratigraphy should also be defined using a systematic methodology that can provide an organised and comprehensive description of the temporal and spatial evolution of volcanic terrain. This review explores different methods employed in studies of volcanic stratigraphy, examines four case studies that use differing stratigraphic approaches, and recommends methods for using systematic volcanic stratigraphy based on the application of the concepts of traditional stratigraphy but adapted to the needs of volcanological environment.

  20. Fluid inclusions in jadeitite and jadeite-rich rock from serpentinite mélanges in northern Hispaniola: Trapped ambient fluids in a cold subduction channel

    Science.gov (United States)

    Kawamoto, Tatsuhiko; Hertwig, Andreas; Schertl, Hans-Peter; Maresch, Walter V.

    2018-05-01

    Freezing-point depression was measured in aqueous fluid inclusions to determine salinities in six samples of jadeitite and jadeite-rich rock from the Jagua Clara serpentinite mélange of the Rio San Juan Complex, Dominican Republic. The mélange represents a fossil subduction-zone channel from a cold, mature subduction zone with a geothermal gradient of 6 °C/km. One hundred and twenty-five determinations of salinity in primary inclusions hosted in jadeite, quartz, apatite and lawsonite range between extremes of 1.2 and 8.7, but yield a well-defined mean of 4.5 ± 1.1 wt% (±1 s.d.) NaCl equiv, slightly higher than mean seawater (3.5 wt%). In one sample, eight additional fluid inclusions in quartz aligned along grain boundaries yield slightly lower values of 2.7 ± 1.3 wt% NaCl equiv. Homogenization temperatures were also measured for 47 fluid inclusions in two samples, but primary entrapment densities are not preserved. It is significant that the suite includes two types of samples: those precipitated directly from an aqueous fluid as well as examples of metasomatic replacement of a pre-existing magmatic rock. Nevertheless, the results indicate identical salinity for both types and suggest a much stronger genetic link between the two types of jadeitite and jadeite-rich rock than has previously been assumed. Based on the results of conductivity measurements in modern subduction zones, we envision a pervasive fluid in the subduction channel that evolved from salinity levels lower than those in sea-water up to the measured values due to on-going but largely completed serpentinization in the subduction channel. The present data represent a reference marker for the subduction channel of the Rio San Juan intra-oceanic subduction zone at 30-50 km depth and after 50-60 Myr of operation.

  1. The nature of hydrothermal fluids in the Kahang porphyry copper deposit (Northeast of Isfahan based on mineralography, fluid inclusion and stable isotopic data

    Directory of Open Access Journals (Sweden)

    Salimeh Sadat Komeili

    2017-02-01

    Full Text Available Introduction The Kahang Cu- Mo deposit is situated approximately 73 Km northeast of Isfahan. Asadi (2007 identified a geological reserve of 40 Mt (proven reserve grading at 0.53 Cu, 0.02 Mo and estimated reserve of 120 Mt. All the rock types in the region have been subjected to hydrothermal solutions which gave rise to three different alteration facies. The dacite and rhyodacite volcanic rocks and granitic- granodioritic stocks have experienced phyllic alteration. Disseminated and stockwork siliceous veins are the major styles of mineralization in this zone. Intermediate argillitic alteration developed on a part of dacitic and rhyodacitic rocks whereas andesite and basaltic-andesite plus related pyroclastic rocks have been subjected to propyllitic alteration. This paper presents the results of geological and mineralogical studies carried out in the Kahang area. This preliminary information is integrated with additional data on ore mineralogy, fluid inclusions and stable isotopes in view of understanding the genesis of the Cu- Mo deposit and the nature of the fluids involved in ore formation. Materials and Methods A total of 18 polished thin sections were prepared at the University of Isfahan for optical study. Fluid inclusions study was carried out on 8 double polished quartz thin sections (stockworks containing ore mineralization from phyllic zone. H – O stable isotope analysis was performed on 4 quartz samples from siliceous stockworks (from phyllic altered zone and one vein epidote sample (from propyllitic zone. All isotopic analyses were performed at the University of Oregan, Oregan, USA. Discussion In the investigated mineralization area, the hypogene zone is characterized by the presence of pyrite, chalcopyrite, bornite and magnetite. Hematite, goethite, jarosite, malachite and azurite are the predominant minerals of supergene zone. The major textures of the primary sulfides are disseminated, vein and veinlet. Pyrite is the most common

  2. Fluid Inclusion Study of The Tumpangpitu High Sulfidation Epithermal Gold Deposit in Banyuwangi District, East Java, Indonesia

    Directory of Open Access Journals (Sweden)

    Yu Yu Myaing

    2018-03-01

    Full Text Available The Tumpangpitu high sulfidation (HS epithermal gold deposit is located in the south coast of East Java, Banyuwangi District, East Java Province, Indonesia. This area lies within the central portion of the Cenozoic Sunda‐Banda magmatic arc which trends southeast from northern Sumatra to west Java then eastward through east Java, Bali, Lombok, Sumbawa and terminating at Banda sea. The geology of the Tumpangpitu is predominantly occupied by Late Oligocene to Middle Miocene low-K calc-alkaline to alkaline andesitic volcanic rocks and interbedded with volcaniclastic rock sequences, which are associated with low-K intermediate intrusions. The mineralization style at the Tumpangpitu area is composed of a high‐sulfidation (HS epithermal gold-copper system which is typically associated with concealed gold-rich porphyry copper system. The HS epithermal mineralization is hosted by volcanic and volcaniclastic rocks in this research area. The mineralization domains are divided into Zone A, Zone B and Zone C which are situated along NW-SE-trending silica ledges zones. The HS epithermal mineralization is texturally occurs as vuggy replacements mineralization as well as stockworks, disseminated forms, fractures and veins. Fluid inclusion study was conducted for 6 quartz vein samples which petrographically entrapped fluid inclusions. Homogenization temperature (Th and melting temperature (Tm can microthermometrically be determined by fluid inclusion analysis. The average homogenization temperature (Th of the fluid inclusions gives 180˚C to 342˚C and melting temperature are from -0.1 ˚C to -1.4˚C. Tm corresponds to the salinities ranging from 0.1 to 4.5 wt% NaCl equivalent. The paleodepth of ore formation can be estimated from the salinity of fluid. Since the deposit was not formed at boiling condition, the minimum paleodepth of ore (quartz samples taken from both shallow level (53.35 m and deep level (135.15 m is determined at 650m and 1,220 m

  3. Evaluation of the inclusion of circular RNAs in mRNA profiling in forensic body fluid identification.

    Science.gov (United States)

    Zhang, Yaqi; Liu, Baonian; Shao, Chengchen; Xu, Hongmei; Xue, Aimin; Zhao, Ziqin; Shen, Yiwen; Tang, Qiqun; Xie, Jianhui

    2018-01-01

    The use of messenger RNA (mRNA) profiling is considered a promising method in the identification of forensically relevant body fluids which can provide crucial information for reconstructing a potential crime. However, casework samples are usually of limited quantity or have been subjected to degradation, which requires improvement of body fluid identification. Circular RNAs (circRNAs), a class of products from the backsplicing of pre-mRNAs, are shown to have high abundance, remarkable stability, and cell type-specific expression in human cells. In this study, we investigated whether the inclusion of circRNAs in mRNA profiling improve the detection of biomarkers including δ-aminolevulinate synthase 2 (ALAS2) and matrix metallopeptidase 7 (MMP7) in body fluid identification. The major circRNAs of ALAS2 and MMP7 were first identified and primer sets for the simultaneous detection of linear and circular transcripts were developed. The inclusion of circRNAs in mRNA profiling showed improved detection sensitivity and stability of biomarkers revealed by using serial dilutions, mixed samples, and menstrual bloodstains as well as degraded and aged samples. Therefore, the inclusion of circRNAs in mRNA profiling should facilitate the detection of mRNA markers in forensic body fluid identification.

  4. Gangue mineral textures and fluid inclusion characteristics of the Santa Margarita Vein in the Guanajuato Mining District, Mexico

    Science.gov (United States)

    Moncada, Daniel; Bodnar, Robert

    2012-06-01

    Successful exploration for mineral deposits requires tools that the explorationist can use to distinguish between targets with high potential for mineralization and those with lower economic potential. In this study, we describe a technique based on gangue mineral textures and fluid inclusion characteristics that has been applied to identify an area of high potential for gold-silver mineralization in the epithermal Ag-Au deposits at Guanajuato, Mexico. The Guanajuato mining district in Mexico is one of the largest silver producing districts in the world with continuous mining activity for nearly 500 years. Previous work conducted on the Veta Madre vein system that is located in the central part of this district identified favorable areas for further exploration in the deepest levels that have been developed and explored. The resulting exploration program discovered one of the richest gold-silver veins ever found in the district. This newly discovered vein that runs parallel to the Veta Madre was named the Santa Margarita vein. Selected mineralized samples from this vein contain up to 249 g/t of Au and up to 2,280 g/t Ag. Fluid inclusions in these samples show homogenization temperatures that range from 184 to 300°C and salinities ranging from 0 to 5 wt.% NaCl. Barren samples show the same range in homogenization temperature, but salinities range only up to 3 wt.% NaCl. Evidence of boiling was observed in most of the samples based on fluid inclusions and/or quartz and calcite textures. Liquid-rich inclusions with trapped illite are closely associated with high silver grades. The presence of assemblages of vapor-rich-only fluid inclusions, indicative of intense boiling or "flashing", shows the best correlation with high gold grades.

  5. Secular variation in the major-ion chemistry of seawater: Evidence from fluid inclusions in Cretaceous halites

    Science.gov (United States)

    Timofeeff, Michael N.; Lowenstein, Tim K.; da Silva, Maria Augusta Martins; Harris, Nicholas B.

    2006-04-01

    The major-ion (Mg 2+, Ca 2+, Na +, K +, SO42-, and Cl -) chemistry of Cretaceous seawater was determined from analyses of seawater-derived brines preserved as fluid inclusions in marine halites. Fluid inclusions in primary halite from three evaporite deposits were analyzed by the environmental scanning electron microscopy (ESEM) X-ray energy dispersive spectrometry (EDS) technique: the Early Cretaceous (Aptian, 121.0-112.2 Ma) of the Sergipe basin, Brazil and the Congo basin, Republic of the Congo, and the Early to Late Cretaceous (Albian to Cenomanian, 112.2-93.5 Ma) of the Khorat Plateau, Laos, and Thailand. The fluid inclusions in halite indicate that Cretaceous seawater was enriched several fold in Ca 2+, depleted in SO42-, Na +, and Mg 2+, and had lower Na +/Cl -, Mg 2+/Ca 2+, and Mg 2+/K + ratios compared to modern seawater. Elevated Ca 2+ concentrations, with Ca 2+ > SO42- at the point of gypsum saturation, allowed Cretaceous seawater to evolve into Mg 2+-Ca 2+-Na +-K +-Cl - brines lacking measurable SO42-.The major-ion composition of Cretaceous seawater was modeled from fluid inclusion chemistries for the Aptian and the Albian-Cenomanian. Aptian seawater was extreme in its Ca 2+ enrichment, more than three times higher than present day seawater, with a Mg 2+/Ca 2+ ratio of 1.1-1.3. Younger, Albian-Cenomanian seawater had lower Ca 2+ concentrations, and a higher Mg 2+/Ca 2+ ratio of 1.2-1.7. Cretaceous (Aptian) seawater has the lowest Mg 2+/Ca 2+ ratios so far documented in Phanerozoic seawater from fluid inclusions in halite, and within the range chemically favorable for precipitation of low-Mg calcite ooids and cements. Results from halite fluid inclusions, together with Mg 2+/Ca 2+ ratios measured from echinoderm and rudist calcite, all indicate that Early Cretaceous seawater (Hauterivian, Barremian, Aptian, and Albian) had lower Mg 2+/Ca 2+ ratios than Late Cretaceous seawater (Coniacian, Santonian, and Campanian). Low Aptian-Albian Mg 2+/Ca 2+ seawater

  6. Fluid inclusions and preliminary studies of hydrothermal alteration in core hole PLTG-1, Platanares geothermal area, Honduras

    Science.gov (United States)

    Bargar, K.E.

    1991-01-01

    The Platanares geothermal area in western Honduras consists of more than 100 hot springs that issue from numerous hot-spring groups along the banks or within the streambed of the Quebrada de Agua Caliente (brook of hot water). Evaluation of this geothermal area included drilling a 650-m deep PLTG-1 drill hole which penetrated a surface mantling of stream terrace deposits, about 550 m of Tertiary andesitic lava flows, and Cretaceous to lower Tertiary sedimentary rocks in the lower 90 m of the drill core. Fractures and cavities in the drill core are partly to completely filled by hydrothermal minerals that include quartz, kaolinite, mixed-layer illite-smectite, barite, fluorite, chlorite, calcite, laumontite, biotite, hematite, marcasite, pyrite, arsenopyrite, stibnite, and sphalerite; the most common open-space fillings are calcite and quartz. Biotite from 138.9-m depth, dated at 37.41 Ma by replicate 40Ar/39 Ar analyses using a continuous laser system, is the earliest hydrothermal mineral deposited in the PLTG-1 drill core. This mid-Tertiary age indicates that at least some of the hydrothermal alteration encountered in the PLTG-1 drill core occured in the distant past and is unrelated to the present geothermal system. Furthermore, homogenization temperatures (Th) and melting-point temperatures (Tm) for fluid inclusions in two of the later-formed hydrothermal minerals, calcite and barite, suggest that the temperatures and concentration of dissolved solids of the fluids present at the time these fluid inclusions formed were very different from the present temperatures and fluid chemistry measured in the drill hole. Liquid-rich secondary fluid inclusions in barite and caicite from drill hole PLTG-1 have Th values that range from about 20??C less than the present measured temperature curve at 590.1-m depth to as much as 90??C higher than the temperature curve at 46.75-m depth. Many of the barite Th measurements (ranging between 114?? and 265??C) plot above the

  7. A study of the gross compositions of oil-bearing fluid inclusions using high performance liquid chromatography

    Energy Technology Data Exchange (ETDEWEB)

    Pang, L.S.K.; George, S.C.; Quezada, R.A. [CSIRO Petroleum, North Ryde (Australia)

    1998-12-31

    A high performance liquid chromatography (HPLC) method for assessing the compositions of crude oils and fluid inclusion oils is described. The necessary increase in instrumentation sensitivity was accomplished using a narrow bore Waters Spherisorb column with 5 {mu}m particle diameter. This HPLC method has advantages over the Iatroscan TLC-FID technique previously described as the < C{sub 16} fraction is measured by the HPLC method. However, due to uncertainties in the calibration procedure the HPLC method is only semi-quantitative. Aliphatic hydrocarbons were calibrated taking into account the molecular weight distribution of a typical oil derived by gas chromatography. Aromatic hydrocarbons were calibrated using standards according to retention times, but the response factors span two orders of magnitude, dependent on ring size. Polar compound response factors are strongly standard dependent. The gross composition of a suite of 12 inclusion oils and 17 co-occurring crude oils from various basins in Australia and Papua New Guinea have been analysed. The inclusion oils at the Jabiru and Tirrawarra wells are enriched in polar compounds relative to the co-occurring crude oils from these wells. This is attributed to an adsorption effect during trapping. However, many inclusion oils do not appear to be polar enriched, which may relate to trapping of inclusion oils in sealed fractures as well as on overgrowths. Inclusion oils tend to be relatively depleted in aromatic hydrocarbons, which could reflect a trapping phenomenon, with preferentially less aromatic hydrocarbons and/or more waxy aliphatic hydrocarbons being trapped in fluid inclusions. Alternatively, this may be a characteristic of the different chemistry of oils that are preserved early in the charge history of a reservoir. (author)

  8. Fluid inclusion chemistry of adularia-sericite epithermal Au-Ag deposits of the southern Hauraki Goldfield, New Zealand

    Science.gov (United States)

    Simpson, Mark P.; Strmic Palinkas, Sabina; Mauk, Jeffrey L.; Bodnar, Robert J.

    2015-01-01

    Microthermometry, laser ablation-inductively coupled plasma-mass spectrometry (LA-ICP-MS), and Raman spectroscopy have been used to determine the temperature, apparent salinity, and composition of individual fluid inclusions in adularia-sericite Au-Ag epithermal veins from the Karangahake, Martha, Favona, and Waitekauri deposits, southern Hauraki goldfield, New Zealand. Quartz veins contain colloform to crustiform bands that alternate with coarse-grained quartz and amethyst. The ore mineralization occurs only in colloform to crustiform bands.

  9. An isotopic and fluid inclusion study of fracture calcite from borehole OL-KR1 at the Olkiluoto site, Finland

    International Nuclear Information System (INIS)

    Blyth, A.; Frape, S.; Blomqvist, R.; Nissinen, P.; McNutt, R.

    1998-04-01

    A study of the geochemistry of fracture filling calcite in borehole OL-KR1 at the radioactive waste disposal investigation site Olkiluoto (in Finland) was undertaken in 1998. The purpose of the present study is to characterize the fracture calcite using mineralogy, oxygen, carbon and strontium isotopes, and fluid inclusions in order to determine past and present chemical and isotopic condition at the site

  10. Mineralogical and Fluid Inclusions Evidence For The Genesis of Umm Addebaa-Umm Kabu Beryl Belt, South Eastern Desert, Egypt

    International Nuclear Information System (INIS)

    Omar, S.A.M.

    2016-01-01

    Beryl mineralization in quartz veins and pegmatites, are common deposits of tectonic-hydrothermal and/or igneous origin. The beryl-specialized granites association at Umm Addebaa-Umm Kabu belt is manifested in the field by the development of a system of beryl-bearing pegmatitic pods and quartz veins. The emplacement of these syn-tectonic pegmatitic leucogranites from which K- and Be-rich fluid phases were derived, are confined to the shear zones, as well as a broad zone of alkali metasomatism. Microthermometic studies of primary fluid inclusions within beryl growth zones are consistent with beryl precipitation from H 2 O-CO 2 ± CH 4 bearing saline brines. The estimated fluid composition is approximately 0.88 mol% H 2 O, 0.017 mol% CO 2 ± 0.001 mol% CH 4 and 0.10 mol% NaCl (2- 11 wt.% NaCl eq.). Fluid inclusion results are consistent with that mineralization in pegmatites and quartz veins that are formed by two genetic stages. The first stage is characterized by temperature of formation in the range of 216.4 - 378.3 °C, with corresponding pressures along fluid inclusion isochore paths ranging from 1.04 to 2.25 bar. The second stage is of aqueous fluid represented with low temperature (177-255°C) and pressure ≤ 1 bar, but high saline (16-22 wt.% NaCl eq.) which might explain mixing of the early carbonaceous fluid with late meteoric water accompanied with pressure release. Thus, it can be inferred that the Be-bearing solutions were moderately saline, but CO 2 (and possible CH 4 )-rich fluid implies that Be was most probably complexed by carbonate ( + CH 4 ) - chloride base. The different paragenetic types of emerald and beryl associated with granitoid rocks indicates that the chemistry of the Be-bearing fluids (rather than that of the bulk rock), and syn-tectonic intrusions of leucogranites and pegmatites (Be deriving sources) along major ductile shear zones are the important factors controlling the crystallization of beryl.

  11. Thermomigration of fluid inclusions in rock salt. Implications for the disposal of nuclear wastes

    International Nuclear Information System (INIS)

    Noack, W.; Runge, K.

    1984-01-01

    A mathematical model has been suggested to predict the time-dependent accumulation of brine at nuclear waste packages emplaced in a rock salt repository owing to thermomigration of brine inclusions. The model is based mainly on a description of the migration rate as a function of the temperature, temperature gradient, inclusion size and gas/liquid ratio of inclusions. Other factors are treated merely as disturbing quantities with respect to the migration rate. (author)

  12. Pressure-temperature condition and hydrothermal-magmatic fluid evolution of the Cu-Mo Senj deposit, Central Alborz: fluid inclusion evidence

    Directory of Open Access Journals (Sweden)

    Ebrahim Tale Fazel

    2017-02-01

    Full Text Available Introduction The Senj deposit has significant potential for different types of mineralization, particularly porphyry-like Cu deposits, associated with subduction-related Eocene–Oligocene calc-alkaline porphyritic volcano-plutonic rocks. The study of fluid inclusions in hydrothermal ore deposits aims to identify and characterize the pressure, temperature, volume and fluid composition, (PTX conditions of fluids under which they were trapped (Heinrich et al., 1999; Ulrich and Heinrich, 2001; Redmond et al., 2004. Different characteristics of the deposit such as porphyrtic nature, alteration assemblage and the quartz-sulfide veins of the stockwork were poorly known. In this approach on the basis of alterations, vein cutting relationship and field distribution of fluid inclusions, the physical and chemical evolution of the hydrothermal system forming the porphyry Cu-Mo (±Au-Ag deposit in Senj is reconstructed. Materials and Methods Over 1000 m of drill core was logged at a scale of 1:1000 by Pichab Kavosh Co. and samples containing various vein and alteration types from different depths were collected for laboratory analyses. A total of 14 samples collected from the altered and least altered igneous rocks in the Senj deposit were analyzed for their major oxide concentrations by X-ray fluorescence in the SGS Mineral Services (Toronto, Canada. The detection limit for major oxide analysis is 0.01%. Trace and rare earth elements (REE were analyzed using inductively coupled plasma-mass spectrometery (ICP-MS, in the commercial laboratory of SGS Mineral Services. The analytical error for most elements is less than 2%. The detection limit for trace elements and REEs analysis is 0.01 to 0.1 ppm. Fluid inclusion microthermometry was conducted using a Linkam THMS600 heating–freezing stage (-190 °C to +600 °C mounted on a ZEISS Axioplan2 microscope in the fluid inclusion laboratory of the Iranian Mineral Processing Research Center (Karaj, Iran. Results

  13. Fluid inclusion and noble gas studies of the Dongping gold deposit, Hebei Province, China: A mantle connection for mineralization?

    Science.gov (United States)

    Mao, J.; Li, Y.; Goldfarb, R.; He, Y.; Zaw, K.

    2003-01-01

    The Dongping gold deposit (>100 t Au) occurs about 200 km inboard of the northern margin of the North China craton. The deposit is mainly hosted by syenite of a middle Paleozoic alkalic intrusive complex that was emplaced into Late Archean basement rocks. Both groups of rocks are intruded by Late Jurassic to Early Cretaceous crustal-melt granite dikes and stocks, some within a few kilometers of the deposit. The gold ores were deposited during this latter magmatic period at about 150 Ma, a time that was characterized by widespread regional north-south compression that formed the east-west-trending Yanshan deformational belt. The ores include both the telluride mineral-bearing, low sulfide quartz veins and the highly K-feldspar-altered syenite, with most of the resource concentrated in two orebodies (1 and 70). Fluid inclusion microthermometry indicates heterogeneous trapping of low-salinity (e.g., 5-7 wt % NaCl equiv) fluids that varied from a few to 60 mole percent nonaqueous volatile species. Laser Raman spectroscopy confirms that the vapor phase in these inclusions is dominated by CO2, but may be comprised of as much as 9 mole percent H2S and 20 mole percent N2; methane concentrations in the vapor phase are consistently variable phase ratios are consistent with fluid immiscibility during ore formation. Fluid inclusion trapping conditions are estimated to be 250?? to 375??C and 0.6 to 1.0 kbar. Helium isotope studies of fluid inclusions in ore-stage pyrites indicate He/He ratios of 2.1 to 5.2 Ra (Ra = 1.4 x 10-6 for air) for orebody 1 and 0.3 to 0.8 Ra for orebody 70. The former data suggest that at least 26 to 65 percent mantle helium occurs in the fluids that deposited the veins in orebody 1. The lower values for orebody 70, which is characterized by a more disseminated style of gold mineralization, are interpreted to reflect an increased interaction of ore fluids with surrounding crustal rocks, which may have contributed additional He to the fluids. A mantle

  14. Geochemical and geophysical investigations, and fluid inclusion studies in the exploration area of Zafarghand (Northeast Isfahan, Iran

    Directory of Open Access Journals (Sweden)

    Zahra Alaminia

    2017-11-01

    Full Text Available Introduction Urumieh-Dokhtar Magmatic Arc (UDMA is a good prospective area for Cu, Cu-Mo and Cu-Au deposits (Fig. 1A and B. The Zafarghand district is located in the central part of the UDMA and the northeastern Isfahan. The present study concerns geological observations, alteration investigations, geochemical data and fluid inclusion studies. The purpose of the research is to identify geochemical anomalies and source of metals in this area. Geochemical anomalies for mineralizing elements and element associations were identified by using statistical analysis methods. Additionally, these results together suggest a site for exploration drilling in this study area. Materials and methods We collected 186 samples (rock along multi-cross sections oriented perpendicular to the strike of the South -Ardestan fault (Fig. 2.Trace element concentrations were determined by the ICP-MS technique in Amdel laboratory (Australia. Thin sections and doubly polished sections (100–200 µm thick from quartz veins were prepared from samples collected from the Zafarghand district in the University of Isfahan. Heating and freezing experiments on fluid inclusions were performed as defined (by Goldstein and Reynolds (1994 on a Linkam THM600 stage. Results Igneous rocks in the Zafarghand area are dominated by the Eocene and post Eocene acidic-intermediate rocks that include dacite, rhyodacite and andesite associated with diorite, quartz diorite and microdiorite intrusions. The present investigations indicate that all rocks of the Zafarghand district exhibit a variety of alterations. Hydrothermal alterations include phyllic, potassic, silicification, and argillic with widespread propylitic. The mineralization consists of malachite, azurite, hematite, and goethite, rare amounts of magnetite, pyrite, and chalcopyrite. Numerical traditional statistical analysis techniques have been applied to interpret the geochemical data of the study area. These methods are aimed at

  15. Ore genesis constraints on the Idaho cobalt belt from fluid inclusion gas, noble gas isotope, and ion ratio analyses--a reply

    Science.gov (United States)

    Hofstra, Albert H.; Landis, Gary P.

    2013-01-01

    Burlinson (2013) questions the veracity of the H2 concentrations reported for fluid inclusion extracts from minerals in the Idaho cobalt belt (Table 2; Landis and Hofstra, 2012) and suggests that they are an analytical artifact of electron-impact mass spectrometry. He also declares that H2 should not be present in fluid inclusions because it is invariably lost by diffusion and is never detected in fluid inclusions by laser Raman. We welcome this opportunity to reply and maintain that the reported H2 contents are accurate. Below we explain why Burlinson’s criticisms are invalid.

  16. Formation conditions of leucogranite dykes and aplite-pegmatite dykes in the eastern Mt. Capanne plutonic complex (Elba, Italy): fluid inclusion studies in quartz, tourmaline, andalusite and plagioclase

    Science.gov (United States)

    Bakker, Ronald J.; Schilli, Sebastian E.

    2016-02-01

    Leucogranite and aplite-pegmatite dykes are associated with the Mt. Capanne pluton (Elba) and partly occur in the thermally metamorphosed host rock (serpentinites). Crystallization conditions of these dykes in the late magmatic-hydrothermal stage are estimated from fluid inclusion studies and mineralogical characterisation, obtained from detailed microthermometry, Raman spectroscopy, and electron microprobe analyses. Fluid inclusion assemblages are analysed in andalusite, quartz, and plagioclase from the leucogranite dykes, and in tourmaline and quartz from the aplite-pegmatite dykes. The fluid inclusion assemblages record multiple pulses of low salinity H2O-rich magmatic and reduced metamorphic fluid stages. Magmatic fluids are characterized by the presence of minor amounts of CO2 and H3BO3, whereas the metamorphic fluids contain CH4 and H2. The highly reduced conditions are also inferred from the presence of native arsenic in some fluid inclusions. Several fluid inclusion assemblages reveal fluid compositions that must have resulted from mixing of both fluid sources. In leucogranite dykes, magmatic andalusite contains a low-density magmatic CO2-rich gas mixture with minor amounts of CH4 and H2. Accidentally trapped crystals (mica) and step-daughters (quartz and diaspore) are detected in some inclusions in andalusite. The first generation of inclusions in quartz that crystallized after andalusite contains a highly reduced H2O-H2 mixture and micas. The second type of inclusions in quartz from the leucogranite is similar to the primary inclusion assemblage in tourmaline from the aplite-pegmatite, and contains up to 4.2 mass% H3BO3, present as a sassolite daughter crystal or dissolved ions, in addition to a CO2-CH4 gas mixture, with traces of H2, N2, H2S, and C2H6. H2O is the main component of all these fluids ( x = 0.91 to 0.96) with maximally 7 mass% NaCl. Some accidentally trapped arsenolite and native arsenic are also detected. These fluids were trapped in the

  17. Direct 40Ar/39Ar age determination of fluid inclusions using in-vacuo¬ stepwise crushing - Example of garnet from the Cycladic Blueschist Unit on Syros

    Science.gov (United States)

    Uunk, Bertram; Postma, Onno; Wijbrans, Jan; Brouwer, Fraukje

    2017-04-01

    Metamorphic minerals and veins commonly trap attending hydrous fluids in fluid inclusions, which yield a wealth of information on the history of the hosting metamorphic system. When these fluids are sufficiently saline, the KCl in the inclusions can be used as a K/Ar geochronologic system, potentially dating inclusion incorporation. Whilst primary fluid inclusions (PFIs) can date fluid incorporation during mineral or vein growth, secondary fluid inclusion trails (SFIs) can provide age constraints on later fluid flow events. At VU Amsterdam, a new in-vacuo crushing apparatus has been designed to extract fluid inclusions from minerals for 40Ar/39Ar analysis. Separates are crushed inside a crusher tube connected to a purification line and a quadrupole mass spectrometer. In-vacuo crushing is achieved by lifting and dropping a steel pestle using an externally controlled magnetic field. As the gas can be analyzed between different crushing steps, the setup permits stepwise crushing experiments. Additionally, crushed powder can be heated by inserting the crusher tube in an externally controlled furnace. Dating by 40Ar/39Ar stepwise crushing has the added advantage that, during neutron irradiation to produce 39Ar from 39K, 38Ar and 37Ar are also produced from 38Cl and 40Ca, respectively. Simultaneous analysis of these argon isotopes permits constraining the chemistry of the argon source sampled during the experiment. This allows a distinction between different fluid or crystal lattice sources. Garnet from three samples of the HP metamorphic Cycladic Blueschist Unit on Syros, Greece was stepwise crushed to obtain fluid inclusion ages. Initial steps for all three experiments yield significant components of excess argon, which are interpreted to originate from grain boundary fluids and secondary fluid inclusions trails. During subsequent steps, age results stabilize to a plateau age. One garnet from North Syros yields an unusually old 80 Ma plateau age. However, isochrons

  18. Study of genesis in Qahr-Abad fluorite deposit using fluid inclusion, southeast of Saqqez, the Kurdistan province

    Directory of Open Access Journals (Sweden)

    Mehrdad Barati

    2017-07-01

    Full Text Available Introduction The Qahr-abad fluorite deposit is located in the area of 36°10′ 3′′ N and 46°34′ 21′′E within the Sanandaj-Sirjan district east of the Kurdistan province , Iran and it is located ~57 km southeast of the city of Saqqez (Kholghi Khasraghi, 1999. This deposit is developed as scatter lenses, veins, and veinlets (stockwork structure within carbonate rocks of Elika formation and controlled by the regional NW–SE trending Zagross thrust nappe system. Fault trends in this area are perpendicular to fault trends in the Zagros zone. The fault dips are nearly vertical and mineralization has occurred in the brecciation fault zone (Talaii, 2010. The rough geological instruction of the deposit has indicated that it is similar to worldwide Epithermal deposits. The mineralization occurs as replacement (type I/ open-space (type II vein fillings and bodies within Mesozoic lime stones (mostly Upper Triassic and Lower Jurassic members of the Elika Formation, where they crop out to form horst structures. The mineralization is typically associated with post Pliocene disjunctive faults, which in part appear to have served as channel ways for the fluorite forming fluids that are representative of the geological setting of the mineralized area. Fluorite occurs in several color variations such as green, violet, blue, white or colorless, and is accompanied by quartz, barite and calcite (Moslehi, 2013. Materials and methods The minerals sampled for the fluid inclusion study include fluorite from mineralization stages. Samples covered all ore types. Micro thermometry analyses for 23 samples were performed after careful microscopic observation of 35 sections and 30 doubly polished sections. Micro thermometry was undertaken using a Linkam THS600 heating-freezing stage, with a measurable temperature range of between −196 and +600 °C (precision of freezing data and homogenization temperature of ±0.2 °C. Micro thermometry was undertaken in the

  19. Exploration of the phase diagram of liquid water in the low-temperature metastable region using synthetic fluid inclusions

    DEFF Research Database (Denmark)

    Qiu, Chen; Krüger, Yves; Wilke, Max

    2016-01-01

    We present new experimental data of the low-temperature metastable region of liquid water derived from high-density synthetic fluid inclusions (996−916 kg/m3) in quartz. Microthermometric measurements include: i) Prograde (upon heating) and retrograde (upon cooling) liquid-vapour homogenisation. ...... a maximum of the bubble nucleation curve in the ϱ–T plane at around 40 °C. The new experimental data represent valuable benchmarks to evaluate and further improve theoretical models describing the p–V–T properties of metastable water in the low-temperature region......We present new experimental data of the low-temperature metastable region of liquid water derived from high-density synthetic fluid inclusions (996−916 kg/m3) in quartz. Microthermometric measurements include: i) Prograde (upon heating) and retrograde (upon cooling) liquid-vapour homogenisation. We...... used single ultrashort laser pulses to stimulate vapour bubble nucleation in initially monophase liquid inclusions. Water densities were calculated based on prograde homogenisation temperatures using the IAPWS-95 formulation. We found retrograde liquid-vapour homogenisation temperatures in excellent...

  20. Analyse ponctuelle des inclusions fluides dans les minéraux par ablation laser femtoseconde ICP-MS: développements et validation

    OpenAIRE

    Courtieu, Clément

    2010-01-01

    Water is one of the most efficient ways to transport chemical elements in Earth, especially in low depth contexts. Mineral deposits are almost always related to dissolution - reprecipitation of these water-transported elements. This water can be trapped inside geological samples as fluid inclusions. Fluid inclusion studies can provide valuable information on trapping conditions and chemical composition of the trapped paleofluid. Laser ablation ICP-MS is a powerful technique for in situ analys...

  1. Search for Fluid Inclusions in a Carbonaceous Chondrite Using a New X-Ray Micro-Tomography Technique Combined with FIB Sampling

    Science.gov (United States)

    Tsuchiyama, A.; Miyake, A.; Zolensky, M. E.; Uesugi, K.; Nakano, T.; Takeuchi, A.; Suzuki, Y.; Yoshida, K.

    2014-01-01

    Early solar system aqueous fluids are preserved in some H chondrites as aqueous fluid inclusions in halite (e.g., [1]). Although potential fluid inclusions are also expected in carbonaceous chondrites [2], they have not been surely confirmed. In order to search for these fluid inclusions, we have developped a new X-ray micro-tomography technique combined with FIB sampling and applied this techniqu to a carbanaceous chondrite. Experimental: A polished thin section of Sutter's Mill meteorite (CM) was observed with an optical microscope and FE-SEM (JEOL 7001F) for chosing mineral grains of carbonates (mainly calcite) and sulfides (FeS and ZnS) 20-50 microns in typical size, which may have aqueous fluid inclusions. Then, a "house" similar to a cube with a roof (20-30 microns in size) is sampled from the mineral grain by using FIB (FEI Quanta 200 3DS). Then, the house was atached to a thin W-needle by FIB and imaged by a SR-based imaging microtomography system with a Fresnel zone plate at beamline BL47XU, SPring-8, Japan. One sample was imaged at two X-ray energies, 7 and 8 keV, to identify mineral phases (dual-enegy microtomography: [3]). The size of voxel (pixel in 3D) was 50-80 nm, which gave the effective spatial resolution of approx. 200 nm. A terrestrial quartz sample with an aqueous fluid inclusion with a bubble was also examined as a test sample by the same method. Results and discussion: A fluid inclusion of 5-8 microns in quartz was clearly identified in a CT image. A bubble of approx. 4 microns was also identified as refraction contrast although the X-ray absorption difference between fluid and bubble is small. Volumes of the fluid and bubble were obtained from the 3D CT images. Fourteen grains of calcite, two grains of iron sulfide and one grain of (Zn,Fe)S were examined. Ten calcite, one iron sulfide and one (Zn,Fe)S grains have inclusions >1 micron in size (the maximum: approx. 5 microns). The shapes are spherical or irregular. Tiny inclusions (tiny solid

  2. Ore genesis constraints on the Idaho Cobalt Belt from fluid inclusion gas, noble gas isotope, and ion ratio analyses

    Science.gov (United States)

    Hofstra, Albert H.; Landis, Gary P.

    2012-01-01

    The Idaho cobalt belt is a 60-km-long alignment of deposits composed of cobaltite, Co pyrite, chalcopyrite, and gold with anomalous Nb, Y, Be, and rare-earth elements (REEs) in a quartz-biotite-tourmaline gangue hosted in Mesoproterozoic metasedimentary rocks of the Lemhi Group. It is the largest cobalt resource in the United States with historic production from the Blackbird Mine. All of the deposits were deformed and metamorphosed to upper greenschist-lower amphibolite grade in the Cretaceous. They occur near a 1377 Ma anorogenic bimodal plutonic complex. The enhanced solubility of Fe, Co, Cu, and Au as chloride complexes together with gangue biotite rich in Fe and Cl and gangue quartz containing hypersaline inclusions allows that hot saline fluids were involved. The isotopes of B in gangue tourmaline are suggestive of a marine source, whereas those of Pb in ore suggest a U ± Th-enriched source. The ore and gangue minerals in this belt may have trapped components in fluid inclusions that are distinct from those in post-ore minerals and metamorphic minerals. Such components can potentially be identified and distinguished by their relative abundances in contrasting samples. Therefore, we obtained samples of Co and Cu sulfides, gangue quartz, biotite, and tourmaline and post-ore quartz veins as well as Cretaceous metamorphic garnet and determined the gas, noble gas isotope, and ion ratios of fluid inclusion extracts by mass spectrometry and ion chromatography. The most abundant gases present in extracts from each sample type are biased toward the gas-rich population of inclusions trapped during maximum burial and metamorphism. All have CO2/CH4 and N2/Ar ratios of evolved crustal fluids, and many yield a range of H2-CH4-CO2-H2S equilibration temperatures consistent with the metamorphic grade. Cretaceous garnet and post-ore minerals have high RH and RS values suggestive of reduced sulfidic conditions. Most extracts have anomalous 4He produced by decay of U and Th and

  3. Effects of post-burial siliceous diagenesis deformations on the microthermometric behaviour of fluid inclusions: an example in the Francevillian uraniferous sandstone reservoir (Gabon)

    International Nuclear Information System (INIS)

    Gauthier-Lafaye, F.; Weber, F.

    1984-01-01

    New data about fluid inclusions associated to a siliceous diagenesis show that a deformation phase in the first stage of catagenesis disturbed their microthermometric behaviour. Nevertheless, temperature and pressure of fluids associated to the uraniferous paragenesis and contemporary with the Oklo natural reactors are estimated at 140-160 0 C and 250-500 bar [fr

  4. Stable isotope and fluid inclusion signatures of hydrothermal fluids in transcrustal fault zones: significance for orogenic, Archean lode-gold mineralization

    International Nuclear Information System (INIS)

    Neumayr, P.; Hagemann, S.G.; Groves, D.I.

    1999-01-01

    mil). Calculated d 18 O fluid compositions for quartz in the CTZ range from 8.0 to 10.3 per mil at 350 deg C (based on arsenopyrite and chlorite thermometry). Hydrogen isotopes from fluid inclusion waters trapped in quartz have a large variation from -62.5 per mil to -7.2 per mil in the CTZ fluids, whereas hydrogen in fluid inclusions in quartz in the second- and third-order shear zones shows a restricted range from -67.6 to -39.8 per mil. The oxygen isotope shift of about 2 per mil from the CTZ to the second- and third-order fault zones may be explained by two competing processes: 1) the hydrothermal fluids in the CTZ equilibrated, at least partially, with metasedimentary rocks in the footwall, and or 2) there was fractionation of oxygen isotopes during phase immiscibility of a combined H 2 O-CO 2 fluid. The preferential trapping of CO 2 -rich fluids in the CTZ, and H 2 O-rich fluids in the second- and third-order fault zones, therefore, could account for the shift in d 18 O. At present, the first process is preferred, because of the ubiquitous presence of the metasedimentary rocks in the footwall and the consistent d 18 O composition of the CTZ, even in hydrothermal quartz veins which contain significant H 2 O. The large variation in the hydrogen isotopes in fluid inclusions in quartz in the CTZ may be explained by late Archean and post-Archean reactivation of the CTZ and the introduction of fluids related to late-fractures fills, whereas apparently minor reactivation of the second- and third-order structures resulted in a restricted range of dD. Copyright (1999) Geological Society of Australia

  5. Extreme alkali bicarbonate- and carbonate-rich fluid inclusions in granite pegmatite from the Precambrian Rønne granite, Bornholm Island, Denmark

    Science.gov (United States)

    Thomas, Rainer; Davidson, Paul; Schmidt, Christian

    2011-02-01

    Our study of fluid and melt inclusions in quartz and feldspar from granite pegmatite from the Precambrian Rønne granite, Bornholm Island, Denmark revealed extremely alkali bicarbonate- and carbonate-rich inclusions. The solid phases (daughter crystals) are mainly nahcolite [NaHCO3], zabuyelite [Li2CO3], and in rare cases potash [K2CO3] in addition to the volatile phases CO2 and aqueous carbonate/bicarbonate solution. Rare melt inclusions contain nahcolite, dawsonite [NaAl(CO3)(OH)2], and muscovite. In addition to fluid and melt inclusions, there are primary CO2-rich vapor inclusions, which mostly contain small nahcolite crystals. The identification of potash as a naturally occurring mineral would appear to be the first recorded instance. From the appearance of high concentrations of these carbonates and bicarbonates, we suggest that the mineral-forming media were water- and alkali carbonate-rich silicate melts or highly concentrated fluids. The coexistence of silicate melt inclusions with carbonate-rich fluid and nahcolite-rich vapor inclusions indicates a melt-melt-vapor equilibrium during the crystallization of the pegmatite. These results are supported by the results of hydrothermal diamond anvil cell experiments in the pseudoternary system H2O-NaHCO3-SiO2. Additionally, we show that boundary layer effects were insignificant in the Bornholm pegmatites and are not required for the origin of primary textures in compositionally simple pegmatites at least.

  6. Conditions for veining in the Barrandian Basin (Lower Palaeozoic), Czech Republic: evidence from fluid inclusion and apatite fission track analysis

    Science.gov (United States)

    Suchy, V.; Dobes, P.; Filip, J.; Stejskal, M.; Zeman, A.

    2002-04-01

    The interplay between fracture propagation and fluid composition and circulation has been examined by deciphering vein sequences in Silurian and Devonian limestones and shales at Kosov quarry in the Barrandian Basin. Three successive vein generations were recognised that can be attributed to different stages of a basinal cycle. Almost all generations of fracture cements host abundant liquid hydrocarbon inclusions that indicate repeated episodes of petroleum migration through the strata during burial, tectonic compression and uplift. The earliest veins that propagated prior to folding were displacive fibrous "beef" calcite veins occurring parallel to the bedding of some shale beds. Hydrocarbon inclusions within calcite possess homogenisation temperatures between 58 and 68 °C and show that the "beef" calcites originated in the deeper burial environment, during early petroleum migration from overpressured shales. E-W-striking extension veins that postdate "beef" calcite formed in response to Variscan orogenic deformations. Based on apatite fission track analysis (AFTA) data and other geological evidence, the veins probably formed 380-315 Ma ago, roughly coinciding with peak burial heating of the strata, folding and the intrusion of Variscan synorogenic granites. The veins that crosscut diagenetic cements and low-amplitude stylolites in host limestones are oriented semi-vertically to the bedding plane and are filled with cloudy, twinned calcite, idiomorphic smoky quartz and residues of hardened bitumen. Calcite and quartz cements contain abundant blue and blue-green-fluorescing primary inclusions of liquid hydrocarbons that homogenise between 50 and 110 °C. Geochemical characteristics of the fluids as revealed by gas chromatography-mass spectrometry, particularly the presence of olefins and parent aromatic hydrocarbons (phenonthrene), suggest that the oil entrapped in the inclusions experienced intense but geologically fast heating that resulted in thermal pyrolysis

  7. Magmatic Vapor Phase Transport of Copper in Reduced Porphyry Copper-Gold Deposits: Evidence From PIXE Microanalysis of Fluid Inclusions

    Science.gov (United States)

    Rowins, S. M.; Yeats, C. J.; Ryan, C. G.

    2002-05-01

    Nondestructive proton-induced X-ray emission (PIXE) studies of magmatic fluid inclusions in granite-related Sn-W deposits [1] reveal that copper transport out of reduced felsic magmas is favored by low-salinity vapor and not co-existing high-salinity liquid (halite-saturated brine). Copper transport by magmatic vapor also has been documented in oxidized porphyry Cu-Au deposits, but the magnitude of Cu partitioning into the vapor compared to the brine generally is less pronounced than in the reduced magmatic Sn-W systems [2]. Consideration of these microanalytical data leads to the hypothesis that Cu and, by inference, Au in the recently established "reduced porphyry copper-gold" (RPCG) subclass should partition preferentially into vapor and not high-salinity liquid exsolving directly from fluid-saturated magmas [3-4]. To test this hypothesis, PIXE microanalysis of primary fluid inclusions in quartz-sulfide (pyrite, pyrrhotite & chalcopyrite) veins from two RPCG deposits was undertaken using the CSIRO-GEMOC nuclear microprobe. PIXE microanalysis for the ~30 Ma San Anton deposit (Mexico) was done on halite-saturated aqueous brine (deposit (W. Australia) was done on halite-saturated "aqueous" inclusions, which contain a small (deposits of the new RPCG subclass demonstrate the greater potential of these systems, compared to the classically oxidized porphyry Cu-Au systems, to transport Cu and probably precious metals in a magmatic aqueous vapor phase. These PIXE data also support the possibility that Cu partitions preferentially into an immiscible CO2-rich magmatic fluid. References: [1] Heinrich, C.A. et al. (1992) Econ. Geol., 87, 1566-1583. [2] Heinrich, C.A. et al. (1999) Geology, 27, 755-758. [3] Rowins, S.M. (2000) Geology, 28, 491-494. [4] Rowins, S.M. (2000) The Gangue, GAC-MDD Newsletter, 67, 1-7 (www.gac.ca). [5] Rowins, S.M. et al. (1993) Geol. Soc. Australia Abs., 34, 68-70.

  8. Fluid inclusion and sulfur stable isotope evidence for the origin of the Ahangran Pb-Ag deposit

    Directory of Open Access Journals (Sweden)

    Mohammad Maanijou

    2015-10-01

    Full Text Available Introduction The Ahangaran Pb-Ag deposit is located in the Hamedan province, west Iran, 25 km southeast of the city of Malayer . . The deposit lies in the strongly folded Sanandaj-Sirjan tectonic zone, in which the ore bodies occur as thin lenses and layers. The host rocks of the deposit are Early Cretaceous carbonates and sandstones that are unconformably underlain by Jurassic rocks. Ore minerals include galena, pyrite, chalcopyrite, pyrrhotite and supergene iron oxide minerals. Gangue minerals consist of barite, dolomite, chlorite, calcite and quartz. The mineralization occurs as open-space fillings, veins, veinlets, disseminations, and massive replacements. Alteration consists of silicification, sericitization, and dolomitization. In this study, we carried out studies of mineralogy, microthermometry of fluid inclusions and sulfur isotopes to determine the source of sulfur and the physico-chemical conditions of formation. Materials and methods Seventy samples of different host rocks, alteration, and mineralization were collected from surface outcrops and different tunnels. Twenty of the samples were prepared for mineralogical studies at Tarbiat Modarres University in Tehran and 25 for petrological studies at the University of Bu-Ali Sina. Fluid-inclusion studies were done on 5 samples of quartz and calcite at Pouya Zamin Azin Company in Tehran using a Linkam THM 600 model heating-freezing stage (with a range of -196 to 480ºC. The accuracy and precision of the homogenization measurements are about ±1°C. Salinity estimates were determined from the last melting temperatures of ice, utilizing the equations by Bodnar and Vityk (1994 and for CO2 fluids using equations by Chen (1972. Nine samples of sulfides and barite were crushed and separated by handpicking under binocular microscope and powdered with agate mortar and pestle. About one gram of each sample was sent to the Stable Isotope and ICP/MS Laboratory of Queen’s University, Canada for

  9. Tourmalinization at the Darasun goldfield, Eastern Transbaikalia: Compositional, fluid inclusion and isotopic constraints

    Directory of Open Access Journals (Sweden)

    Vsevolod Prokofiev

    2012-01-01

    Full Text Available Zoned tourmaline (schorl-dravite in the matrix of hydrothermal explosive breccia and ore veins in gold deposits, Chita region, Eastern Transbaikalia, Russia, are associated with Na- and K-rich porphyry-type subvolcanic intrusives. δ18O values of tourmaline from three gold deposits (Darasun, Talatui, Teremkinskoye are +8.3‰, +7.6‰, and +6.0‰ and calculated δ18O values of fluids responsible for the tourmalinization are +7.3‰, +7.7‰, and +4.2‰, respectively. These data imply an igneous fluid source, except at the Teremkin deposit where mixing with meteoric water is indicated. Wide ranges of Fe3+/Fetot and the presence of vacancies characterize the Darasun deposit tourmaline indicating wide ranges of ƒ(O2 and pH of mineralizing fluids. Initial stage tourmalines from the gold deposits of the Darasun ore district are dravite or high mg schorl. Second stage tourmaline is characterized by oscillatory zoning but with Fe generally increasing towards crystal rims indicating decreasing temperature. Third stage tourmaline formed unzoned crystals with xMg (mole fraction of Mg close to that of the first stage tourmaline, due to a close association with pyrite and arsenopyrite. From Fe3+/Fetot values, chemical composition and crystallization temperatures, logf(O2 of mineralizing fluids ranged from ca. −25 to −20, much higher than for the gold-bearing beresite–listvenite association, indicating that tourmalinization was not related to gold mineralization.

  10. Characterization of gas chemistry and noble-gas isotope ratios of inclusion fluids in magmatic-hydrothermal and magmatic-steam alunite

    Science.gov (United States)

    Landis, G.P.; Rye, R.O.

    2005-01-01

    Chemical and isotope data were obtained for the active gas and noble gas of inclusion fluids in coarse-grained samples of magmatic-hydrothermal and magmatic-steam alunite from well-studied deposits (Marysvale, Utah; Tambo, Chile; Tapajo??s, Brazil; Cactus, California; Pierina, Peru), most of which are discussed in this Volume. Primary fluid inclusions in the alunite typically are less than 0.2 ??m but range up to several micrometers. Analyses of the active-gas composition of these alunite-hosted inclusion fluids released in vacuo by both crushing and heating indicate consistent differences in the compositions of magmatic-hydrothermal and magmatic-steam fluids. The compositions of fluids released by crushing were influenced by contributions from significant populations of secondary inclusions that trapped largely postdepositional hydrothermal fluids. Thermally released fluids gave the best representation of the fluids that formed primary alunite. The data are consistent with current models for the evolution of magmatic-hydrothermal and magmatic-steam fluids. Magmatic-steam fluids are vapor-dominant, average about 49 mol% H2O, and contain N2, H2, CH4, CO, Ar, He, HF, and HCl, with SO2 the dominant sulfur gas (average SO2/ H2S=202). In contrast, magmatic-hydrothermal fluids are liquid-dominant, average about 88 mol% H2O, and N2, H2, CO2, and HF, with H2S about as abundant as SO2 (average SO2/H2 S=0.7). The low SO2/H2S and N2/Ar ratios, and the near-absence of He in magmatic-hydrothermal fluids, are consistent with their derivation from degassed condensed magmatic fluids whose evolution from reduced-to-oxidized aqueous sulfur species was governed first by rock and then by fluid buffers. The high SO2/H2S and N2/Ar with significant concentrations of He in magmatic-steam fluids are consistent with derivation directly from a magma. None of the data supports the entrainment of atmospheric gases or mixing of air-saturated gases in meteoric water in either magmatic

  11. Mineralogy and fluid inclusion studies in kalchoye Copper- gold deposit, East of Esfahan

    Directory of Open Access Journals (Sweden)

    Rezvan Mehvary

    2009-09-01

    Full Text Available Kalchoye Copper-gold deposit is located about 110 kilometers east of Esfahan province and within the Eocene volcano sedimentary rocks. Sandy tuff and andesite lava are important members of this complex.The form of mineralization in area is vein and veinlet and quartz as the main gangue phase. The main ore minerals are chalcopyrite, chalcocite, galena and weathered minerals such as goethite, iron oxides, malachite and azurite. Studies in area indicate that ore mineralization Kalchoye is low sulfide, quartz type of hydrothermal ore deposits and results of thermometry studies on quartz minerals low- medium fluid with low potential mineralization is responsible for mineralization in this area.

  12. Metamorphic fluid flow in the northeastern part of the 3.8-3.7 Ga Isua Greenstone Belt (SW Greenland): A re-evalution of fluid inclusion evidence for early Archean seafloor-hydrothermal systems

    DEFF Research Database (Denmark)

    Heijlen, Wouter; Appel, P. W. U.; Frezzotti, M. L.

    2006-01-01

    Fluid inclusions in quartz globules and quartz veins of a 3.8-3.7 Ga old, well-preserved pillow lava breccia in the northeastern Isua Greenstone Belt (IGB) were studied using microthermometry, Raman spectrometry and SEM Cathodoluminescence Imaging. Petrographic study of the different quartz......-rich (+H2O, +graphite) and brine-rich (+CO2, +halite, +carbonate) inclusions. The gas-rich inclusions have molar volumes between 44.8 and 47.5 cm(3)/Mol, while the brine inclusions have a salinity of similar to 33 eq. wt% NaCl. Modeling equilibrium immiscibility using volumetric and compositional...

  13. Thermal evolution of Site U1414 by stable isotopes δ13C and δ18O, 87Sr/86Sr and fluid inclusion analyses, IODP Expedition 344

    Science.gov (United States)

    Brandstätter, Jennifer; Kurz, Walter; Krenn, Kurt; Richoz, Sylvain

    2017-04-01

    IODP Expedition 344 is the second expedition in course of the Costa Rica Seismogenesis Project (Program A), that was designed to reveal processes that effect nucleation and seismic rupture of large earthquakes at erosional subduction zones. Site 344-U1414, located 1 km seaward of the deformation front offshore Costa Rica, serves to evaluate fluid-rock interaction and geochemical processes linked with the tectonic evolution of the incoming Cocos Plate from the Early Miocene up to recent times. Combined isotope analyses and microthermometric analyses of fluid inclusions of hydrothermal veins within lithified sediments and the igneous basement (Cocos Ridge basalt), was used to reveal the thermal history of Site 344-U1414. Veins in the sedimentary rocks are mainly filled by coarse-grained calcite and subordinately by quartz. Veins within the basalt show polymineralic filling of clay minerals, calcite, aragonite and quartz. Blocky veins with embedded wall rock fragments, appearing in the sediments and in the basalt, indicate hydraulic fracturing. The carbon isotopic composition of the vein calcite suggest the influence of a CO2 -rich fluid mixed with seawater (-3.0 to -0.4‰ V-PDB) and the δ18O values can be differentiated in two groups, depending on the formation temperature (-13.6 to -9.3‰ and -10.8 to -4.7‰ V-PDB). 87Sr/86Sr ratios from the veins confirm the results of the stable isotope analyses, with a higher 87Sr/86Sr ratio close to seawater composition and lower ratios indicating the influence of basalt alteration. The hydrothermal veins contain different types of fluid inclusions with high and low entrapment temperatures and low saline fluids. The occurrence of decrepitated fluid inclusions, formed by increased internal overpressure, is related to isobaric heating. Elongated fluid inclusion planes, arc-like fluid inclusions and low homogenization temperatures suggest subsequent isobaric cooling. The stable isotopic content, strontium isotopic composition

  14. Preliminary report on fluid inclusions from halites in the Castile and lower Salado formations of the Delaware Basin, southeastern New Mexico

    International Nuclear Information System (INIS)

    Stein, C.L.

    1985-09-01

    A suite of samples composed primarily of halite from the upper Castile and lower Salado Formations of the Permian Basin was selected from Waste Isolation Pilot Plant (WIPP) core for a reconnaissance study of fluid inclusions. Volume percent of these trapped fluids averaged 0.7% to 1%. Freezing-point depressions varied widely and appeared to be unrelated to fluid-inclusion type, to sedimentary facies, or to stratigraphic depth. However, because very low freezing points were usually associated with anhydrite, a relation may exist between freezing-point data and lithology. Dissolved sulfate values were constant through the Castile, then decreased markedly with lesser depth in the lower Salado. This trend correlates very well with observed mineralogy and is consistent with an interpretation of the occurrence of secondary polyhalite as a result of gypsum or anhydrite alteration with simultaneous consumption of dissolved sulfate from the coexisting fluids. Together with the abundance and distribution of fluid inclusions in primary or ''hopper'' crystal structures, this evidence suggests that inclusions seen in these halites did not migrate any significant geographical distance since their formation. 28 refs., 17 figs., 2 tabs

  15. Dynamics of mineral crystallization at inclusion-garnet interface from precipitated slab-derived fluid phase: first in-situ synchrotron x-ray measurements

    Science.gov (United States)

    Malaspina, Nadia; Alvaro, Matteo; Campione, Marcello; Nestola, Fabrizio

    2015-04-01

    Remnants of the fluid phase at ultrahigh pressure (UHP) in subduction environments may be preserved as primary multiphase inclusions in UHP minerals. These inclusions are frequently hosted by minerals stable at mantle depths, such as garnet, and show the same textural features as fluid inclusions. The mineral infillings of the solid multiphase inclusions are generally assumed to have crystallized by precipitation from the solute load of dense supercritical fluids equilibrating with the host rock. Notwithstanding the validity of this assumption, the mode of crystallization of daughter minerals during precipitation within the inclusion and/or the mechanism of interaction between the fluid at supercritical conditions and the host mineral are still poorly understood from a crystallographic point of view. A case study is represented by garnet orthopyroxenites from the Maowu Ultramafic Complex (China) deriving from harzburgite precursors metasomatised at ~ 4 GPa, 750 °C by a silica- and incompatible trace element-rich fluid phase. This metasomatism produced poikilitic orthopyroxene and inclusion-rich garnet porphyroblasts. Solid multiphase primary inclusions in garnet display a size within a few tens of micrometers and negative crystal shapes. Infilling minerals (spinel: 10-20 vol.%; amphibole, chlorite, talc, mica: 80- 90 vol.%) occur with constant volume ratios and derive from trapped solute-rich aqueous fluids. To constrain the possible mode of precipitation of daughter minerals, we performed for the first time a single-crystal X-ray diffraction experiment by means of Synchrotron Radiation at DLS-Diamond Light Source. In combination with electron probe microanalyses, this measurement allowed the unique identification of each mineral phase and their reciprocal orientations. We demonstrated the epitaxial relationship between spinel and garnet and between some hydrous minerals. Epitaxy drives a first-stage nucleation of spinel under near-to-equilibrium conditions

  16. Metal-rich fluid inclusions provide new insights into unconformity-related U deposits (Athabasca Basin and Basement, Canada)

    Science.gov (United States)

    Richard, Antonin; Cathelineau, Michel; Boiron, Marie-Christine; Mercadier, Julien; Banks, David A.; Cuney, Michel

    2016-02-01

    The Paleoproterozoic Athabasca Basin (Canada) hosts numerous giant unconformity-related uranium deposits. The scope of this study is to establish the pressure, temperature, and composition (P-T-X conditions) of the brines that circulated at the base of the Athabasca Basin and in its crystalline basement before, during and after UO2 deposition. These brines are commonly sampled as fluid inclusions in quartz- and dolomite-cementing veins and breccias associated with alteration and U mineralization. Microthermometry and laser ablation-inductively coupled plasma-mass spectrometry (LA-ICP-MS) data from five deposits (Rabbit Lake, P-Patch, Eagle Point, Millennium, and Shea Creek) complement previously published data for the McArthur River deposit. In all of the deposits investigated, fluid inclusion salinity is between 25 and 40 wt.% NaCl equiv., with compositions displaying a continuum between a "NaCl-rich brine" end-member (Cl > Na > Ca > Mg > K) and a "CaCl2-rich brine" end-member (Cl > Ca ≈ Mg > Na > K). The CaCl2-rich brine has the highest salinity and shows evidence for halite saturation at the time of trapping. The continuum of compositions between the NaCl-rich brine and the CaCl2-rich brine end-members combined with P-T reconstructions suggest anisothermal mixing of the two brines (NaCl-rich brine, 180 ± 30 °C and 800 ± 400 bars; CaCl2-rich brine, 120 ± 30 °C and 600 ± 300 bars) that occurred under fluctuating pressure conditions (hydrostatic to supra-hydrostatic). However, because the two brines were U bearing and therefore oxidized, brine mixing was probably not the driving force for UO2 deposition. Several scenarios are put forward to account for the Cl-Na-Ca-Mg-K composition of the brines, involving combinations of seawater evaporation, halite dissolution, mixing with a halite-dissolution brine, Mg/Ca exchange by dolomitization, Na/Ca exchange by albitization of plagioclase, Na/K exchange by albitization of K-feldspar, and Mg loss by Mg

  17. Dating quartz: Ar/Ar analyses of coexisting muscovite and fluid inclusion - rich quartz from paleocene amorphic aureole

    International Nuclear Information System (INIS)

    Matthews, S.J.; Perez de Arce, C.; Cornejo, P.; Cuitino, L; Klein, J

    2001-01-01

    We present Ar/Ar total fusion and step-heating data for coexisting muscovite and white quartz from the metamorphic aureole of the Lower Paleocene La Copiapina Pluton, 6 km south of Inca de Oro, III Region, Chile. The pluton intrudes the upper clastic sedimentary member of the Punta del Cobre Group (Upper Jurassic - Lower Cretaceous) and the calcareous sedimentary rocks of the Chanarcillo Group (Neocomian), and comprises fine to coarse grained pyroxene-hornblende-biotite quartz diorites and monzodiorites. Its emplacement was controlled on its north-western side by a subvertical NE-trending fault, along which were developed vertically banded skarns (skarn mylonite), suggesting syntectonic intrusion. Biotite K-Ar ages for the pluton fall in the range 61-63 Ma, relating it to a latest Cretaceous to Lowest Paleocene syn-compressional intrusive belt which is present in the area (Matthews and Cornejo, 2000). A metamorphic / metasomatic aureole is developed within the sandstones of the Punta del Cobre Group, on the extreme northern limit of the pluton. In this area, the sedimentary rocks have been replaced by quartz-sericite and quartz-muscovite assemblages, with minor hematite and tourmaline, and late supergene kaolinite and pyrophyllite. A coarse muscovite-quartz-tourmaline-hematite assemblage is developed in and around older (early Upper Cretaceous) andesitic dykes, in the form of replacement / fracture fill veins and replacement zones. Further from the contact with the pluton, fine-grained quartz-sericite rock with coarser muscovite-rich replacement veins represents the dominant lithology. Quartz in the coarse replacement rock is very rich in fluid inclusions. Primary inclusions are mainly of two coexisting types; bi-phase (liquid and gas bubble) and tri-phase (liquid, gas bubble and halite crystal), indicating that the quartz formed in the presence of a boiling fluid. Some inclusions also contain sylvite and occasional hematite daughter crystals. Secondary inclusions

  18. Fluid inclusion and oxygen-isotope evidence for low-temperature Au-Pt-Pd (± U) mineralization at Corronation Hill, NT

    International Nuclear Information System (INIS)

    Mernagh, T.

    1992-01-01

    The fluid inclusion and isotope data have been used to constrain the ore genesis models for the Au-Pt-Pd-U mineralization at Coronation Hill. The fluid inclusions demonstrate that the ore fluid was strongly saline with an unusually high CaCl 2 content, and that the mineralisation was probably formed from a boiling fluid at around 140 deg C. Furthermore, the fluids were highly oxidised and the replacement of earlier chlorite by hematite is common throughout the deposit. It is concluded that both U-rich and U-poor Au-Pt-Pd mineralisation were formed by descending, low-temperature, highly oxidised, very saline, meteoric fluids. The segregation of U was controlled by fluid-rock interaction in the feldspathic or carbonate rocks. Interaction with carbonaceous or chloritic rocks resulted in a reduction in fO 2 , and consequent precipitation of U, Au, Pt and Pd. The other two types of metal associations can be explained by further reaction of the mineralizing fluids. 3 figs

  19. Quartz-Amethyst Hosted Hydrocarbon-Bearing Fluid Inclusions from the Green Ridge Breccia in the Snoqualmie Granite, North Cascades, WA, USA

    Directory of Open Access Journals (Sweden)

    Martin Feely

    2017-09-01

    Full Text Available The Green Ridge Breccia cuts the composite Miocene Snoqualmie Batholith in King County, WA, USA. The granite was emplaced at ~5 km depth between ~17 and 20 Ma and the crosscutting NW trending breccia contains large angular blocks of the host granite (<1 m in longest dimension. The brecciated granite blocks are cemented by quartz-amethyst euhedra (<10 cm in longest dimension bearing vugs. A notable feature is the presence of centimetric scale amber coloured oil inclusions within the quartz-amethyst crystals. Fluid inclusion studies using Transmitted Light Petrography, UV Microscopy, Microthermometry, Laser Raman Microspectroscopy and Gas Chromatography-Mass Spectrometry record the presence and the fluid composition of three fluid inclusion types hosted by the euhedra: primary Type 1 (liquid rich two-phase (L + V aqueous inclusions and secondary Type 2 bituminous two-phase (S + L inclusions and Type 3 amber coloured oil bearing two-phase immiscible liquid inclusions. The Green Ridge Breccia was the locus for convective hydrothermal fluid flow that formed the quartz-amethyst vugs formed at T~390 °C assuming a trapping pressure of ~1.65 kb. Later, hydrocarbon fluids migrated downwards from the roof source rock (e.g., the Guye Sedimentary Member and were trapped in the euhedra. This was followed by unroofing of the batholith and exposure of the Green Ridge Breccia. This study highlights the potential for other oil migrations into the Snoqualmie Batholith in areas where it forms the basement capped by the Guye Sedimentary Member.

  20. Temporal and spatial distribution of alteration, mineralization and fluid inclusions in the transitional high-sulfidation epithermal-porphyry copper system at Red Mountain, Arizona

    Science.gov (United States)

    Lecumberri-Sanchez, Pilar; Newton, M. Claiborne; Westman, Erik C.; Kamilli, Robert J.; Canby, Vertrees M.; Bodnar, Robert J.

    2013-01-01

    Red Mountain, Arizona, is a Laramide porphyry Cu system (PCD) that has experienced only a modest level of erosion compared to most other similar deposits in the southwestern United States. As a result, the upper portion of the magmatic–hydrothermal system, which represents the transition from shallower high-sulfidation epithermal mineralization to deeper porphyry Cu mineralization, is well preserved. Within the Red Mountain system, alteration, mineralization and fluid inclusion assemblages show a systematic distribution in both time and space. Early-potassic alteration (characterized by the minerals biotite and magnetite) is paragenetically earlier than late-potassic alteration (K-feldspar–anhydrite) and both are followed by later phyllic (sericite–pyrite) alteration. Advanced argillic alteration (pyrophyllite–alunite–other clay minerals) is thought to be coeval with or postdate phyllic alteration. Minerals characteristic of advanced argillic alteration are present in the near surface. Phyllic alteration extends to greater depths compared to advanced argillic alteration. Early-potassic and late-potassic alteration are only observed in the deepest part of the system. Considerable overlap of phyllic alteration with both early-potassic and late-potassic alteration zones is observed. The hypogene mineralization contains 0.4–1.2% Cu and is spatially and temporally related to the late-potassic alteration event. Molybdenum concentration is typically In the deepest part of the system, an early generation of low-to-moderate density and salinity liquid + vapor inclusions with opaque daughter minerals is followed in time by halite-bearing inclusions that also contain opaque daughter minerals indicating that an early intermediate-density magmatic fluid evolved to a high-density, high-salinity mineralizing fluid. The increase in density and salinity of fluids with time observed in the deeper parts of the system may be the result of immiscibility (“boiling”) of

  1. Sulfate brines in fluid inclusions of hydrothermal veins: Compositional determinations in the system H2O-Na-Ca-Cl-SO4

    Science.gov (United States)

    Walter, Benjamin F.; Steele-MacInnis, Matthew; Markl, Gregor

    2017-07-01

    Sulfate is among the most abundant ions in seawater and sulfate-bearing brines are common in sedimentary basins, among other environments. However, the properties of sulfate-bearing fluid inclusions during microthermometry are as yet poorly constrained, restricting the interpretation of fluid-inclusion compositions where sulfate is a major ion. The Schwarzwald mining district on the eastern shoulder of the Upper Rhinegraben rift is an example of a geologic system characterized by sulfate-bearing brines, and constraints on the anion abundances (chloride versus sulfate) would be desirable as a potential means to differentiate fluid sources in hydrothermal veins in these regions. Here, we use the Pitzer-type formalism to calculate equilibrium conditions along the vapor-saturated liquidus of the system H2O-Na-Ca-Cl-SO4, and construct phase diagrams displaying the predicted phase equilibria. We combine these predicted phase relations with microthermometric and crush-leach analyses of fluid inclusions from veins in the Schwarzwald and Upper Rhinegraben, to estimate the compositions of these brines in terms of bulk salinity as well as cation and anion loads (sodium versus calcium, and chloride versus sulfate). These data indicate systematic differences in fluid compositions recorded by fluid inclusions, and demonstrate the application of detailed low-temperature microthermometry to determine compositions of sulfate-bearing brines. Thus, these data provide new constraints on fluid sources and paleo-hydrology of these classic basin-hosted ore-forming systems. Moreover, the phase diagrams presented herein can be applied directly to compositional determinations in other systems.

  2. Origin of the Okrouhlá Radouň episyenite-hosted uranium deposit, Bohemian Massif, Czech Republic: fluid inclusion and stable isotope constraints

    Czech Academy of Sciences Publication Activity Database

    Dolníček, Z.; René, Miloš; Hermannová, S.; Prochaska, W.

    2014-01-01

    Roč. 49, č. 4 (2014), s. 409-425 ISSN 0026-4598 R&D Projects: GA MŠk ME10083 Institutional support: RVO:67985891 Keywords : Bohemian Massif * Uranium mineralization * Episyenite * Fluid inclusions Subject RIV: DB - Geology ; Mineralogy Impact factor: 2.561, year: 2014

  3. Last glacial and Holocene stable isotope record of fossil dripwater from subtropical Brazil based on analysis of fluid inclusions in stalagmites

    NARCIS (Netherlands)

    Millo, Christian; Strikis, Nicolás M.; Vonhof, Hubert B.; Deininger, Michael; da Cruz, Francisco W.; Wang, Xianfeng; Cheng, Hai; Lawrence Edwards, R.

    2017-01-01

    The stable isotope composition of fossil dripwater preserved in stalagmites fluid inclusions is a promising tool to reconstruct paleopluviosity in the tropics and subtropics. Here we present δD and δ18O records of fossil dripwater from two stalagmites collected in Botuverá Cave (subtropical Brazil),

  4. Bicarbonate-rich fluid inclusions and hydrogen diffusion in quartz from the Libčice orogenic gold deposit, Bohemian Massif

    Czech Academy of Sciences Publication Activity Database

    Hrstka, Tomáš; Dubessy, J.; Zachariáš, J.

    2011-01-01

    Roč. 281, 3-4 (2011), s. 317-332 ISSN 0009-2541 Institutional research plan: CEZ:AV0Z30130516 Keywords : bicarbonate * fluid inclusions * hydrogen diffusion * orogenic gold deposits * raman spectroscopy Subject RIV: DB - Geology ; Mineralogy Impact factor: 3.518, year: 2011

  5. High resolution, high sensitivity imaging and analysis of minerals and inclusions (fluid and melt) using the new CSIRO-GEMOC nuclear microprobe

    International Nuclear Information System (INIS)

    Ryan, C.G.; McInnes, B.M.; Van Achterbergh, E.; Williams, P.J.; Dong, G.; Zaw, K.

    1999-01-01

    Full text: The new CSIRO-GEMOC Nuclear Microprobe (NMP) The instrument was designed specifically for minerals analysis and imaging and to achieve ppm to sub-ppm sensitivity at a spatial resolution of 1-2 μm using X-rays and y-rays induced by MeV energy ion beams. The key feature of the design is a unique magnetic quadrupole quintuplet ion focussing system that combines high current with high spatial resolution (Ryan et al., 1999). These design goals have been achieved or exceeded. On the first day of operation, a spot-size of 1.3 μm was obtained at a beam current of 0.5 nA, suitable for fluid inclusion analysis and imaging. The spot-size grows to just 1.8 μm at 10 nA (3 MeV protons), ideal for mineralogical samples with detection limits down to 0.2 ppm achieved in quantitative, high resolution, trace element images. Applications of the NMP include: research into ore deposit processes through trace element geochemistry, mineralogy and fluid inclusion analysis of ancient deposits and active sea-floor environments, ore characterization, and fundamental studies of mantle processes and extraterrestrial material. Quantitative True Elemental Imaging Dynamic Analysis is a method for projecting quantitative major and trace element images from proton-induced X-ray emission (PIXE) data obtained using the NMP (Ryan et al., 1995). The method un-mixes full elemental spectral signatures to produce quantitative images that can be directly interrogated for the concentrations of all elements in selected areas or line projections, etc. Fluid Inclusion Analysis and Imaging The analysis of fluids trapped as fluid inclusions in minerals holds the key to understanding ore metal pathways and ore formation processes. PIXE analysis using the NMP provides a direct non-destructive method to determine the composition of these trapped fluids with detection limits down to 20 ppm. However, some PIXE results have been controversial, such as the strong partitioning of Cu into the vapour phase (e

  6. Fluid Inclusion and Oxygen Isotope Constraints on the Origin and Hydrothermal Evolution of the Haisugou Porphyry Mo Deposit in the Northern Xilamulun District, NE China

    Directory of Open Access Journals (Sweden)

    Qihai Shu

    2017-01-01

    Full Text Available The Haisugou porphyry Mo deposit is located in the northern Xilamulun district, northeastern China. Based on alteration and mineralization styles and crosscutting relationships, the hydrothermal evolution in Haisugou can be divided into three stages: an early potassic alteration stage with no significant metal deposition, a synmineralization sericite-chlorite alteration stage with extensive Mo precipitation, and a postmineralization stage characterized by barren quartz and minor calcite and fluorite. The coexistence of high-salinity brine inclusions with low-salinity inclusions both in potassic alteration stage (~440°C and locally in the early time of mineralization stage (380–320°C indicates the occurrence of fluid boiling. The positive correlations between the homogenization temperatures and the salinities of the fluids and the low oxygen isotopic compositions (δ18Ofluid < 3‰ of the syn- to postmineralization quartz together suggest the mixing of magmatic fluids with meteoric water, which dominated the whole mineralization process. The early boiling fluids were not responsible for ore precipitation, whereas the mixing with meteoric water, which resulted in temperature decrease and dilution that significantly reduced the metal solubility, should have played the major role in Mo mineralization. Combined fluid inclusion microthermometry and chlorite geothermometer results reveal that ore deposition mainly occurred between 350 and 290°C in Haisugou.

  7. Stable isotope and fluid inclusion evidence for the origin of the Brandberg West area Sn-W vein deposits, NW Namibia

    Science.gov (United States)

    Macey, Paul; Harris, Chris

    2006-10-01

    The Brandberg West region of NW Namibia is dominated by poly-deformed turbidites and carbonate rocks of the Neoproterozoic Damara Supergoup, which have been regionally metamorphosed to greenschist facies and thermally metamorphosed up to mid-amphibolite facies by Neoproterozoic granite plutons. The meta-sedimentary rocks host Damaran-age hydrothermal quartz vein-hosted Sn-W mineralization at Brandberg West and numerous nearby smaller deposits. Fluid inclusion microthermometric studies of the vein quartz suggests that the ore-forming fluids at the Brandberg West mine were CO2-bearing aqueous fluids represented by the NaCl-CaCl2-H2O-CO2 system with moderate salinity (mean=8.6 wt% NaClequivalent).Temperatures determined using oxygen isotope thermometry are 415-521°C (quartz-muscovite), 392-447°C (quartz-cassiterite), and 444-490°C (quartz-hematite). At Brandberg West, the oxygen isotope ratios of quartz veins and siliciclastic host rocks in the mineralized area are lower than those in the rocks and veins of the surrounding areas suggesting that pervasive fluid-rock interaction occurred during mineralization. The O- and H-isotope data of quartz-muscovite veins and fluid inclusions indicate that the ore fluids were dominantly of magmatic origin, implying that mineralization occurred above a shallow granite pluton. Simple mass balance calculations suggest water/rock ratios of 1.88 (closed system) and 1.01 (open system). The CO2 component of the fluid inclusions had similar δ 13C to the carbonate rocks intercalated with the turbidites. It is most likely that mineralization at Brandberg West was caused by a combination of an impermeable marble barrier and interaction of the fluids with the marble. The minor deposits in the area have quartz veins with higher δ 18O values, which is consistent with these deposits being similar geological environments exposed at higher erosion levels.

  8. The evolution of pegmatite-hosted Sn-W mineralization at Nong Sua, Thailand: Evidence from fluid inclusions and stable isotopes

    Science.gov (United States)

    Linnen, Robert L.; Williams-Jones, Anthony E.

    1994-01-01

    The Nong Sua aplite-pergmatite complex contains two dominant styles of Sn-W-Ta-Nb mineralization. Cassiterite ± Nb-Ta-Ti oxide minerals are disseminated in the pegmatite, and cassiterite and wolframite are hosted by quartz-tourmaline veins which are contained solely within aplite. The orthomagmatic fluid at Nong Sua is preserved as primary fluid inclusions in the cores of magmatic garnet crystals that have high tin concentrations (garnet cores without fluid inclusions do not contain elevated tin concentrations). These fluid inclusions have a composition of 3 wt% NaCl eq. The low salinity suggests that, at vapor saturation, tin was partitioned in favour of the melt, which allowed cassiterite to initially crystallize directly from the melt. Primary, pseudosecondary, and secondary fluid inclusions in cassiterite, tourmaline, and quartz record three-component mixing of the orthomagmatic fluid with high salinity aqueous and with CO 2-rich fluids. The orthomagmatic water is interpreted to have had δ 18O value of +8.7 to +9.9 per mil and a δD value of -72 to -78 per mil from δ18O analyses of muscovite and quartz, and δD of muscovite. The δ18O composition of muscovite decreased from 10.1 to 8.0 per mil and δD increased from - 106 to - 85 per mil, from the magmatic to the hydrothermal stages of pegmatite evolution. These changes are consistent with an influx of metamorphic fluids or evolved meteoric waters. We consider that the saturation of the melt with vapor caused the pressure in the pegmatite to rise to approximately 3.8 kbar, at a temperature of 650°C. Fluid overpressure caused the aplite to fracture, and veins to form from fluids which migrated into the fracture-induced low pressure zones. This event can be modeled by an isothermal decompression to 2.7 kbar. Cassiterite deposition was probably controlled by increasing fO 2, whereas wolframite deposition resulted from the mixing of W-rich with Fe-Mn-rich fluids. In both cases decompression, cooling, and

  9. Formation of Archean batholith-hosted gold veins at the Lac Herbin deposit, Val-d'Or district, Canada: Mineralogical and fluid inclusion constraints

    Science.gov (United States)

    Rezeau, Hervé; Moritz, Robert; Beaudoin, Georges

    2017-03-01

    The Lac Herbin deposit consists of a network of mineralized, parallel steep-reverse faults within the synvolcanic Bourlamaque granodiorite batholith at Val-d'Or in the Archean Abitibi greenstone belt. There are two related quartz-tourmaline-carbonate fault-fill vein sets in the faults, which consist of subvertical fault-fill veins associated with subhorizontal veins. The paragenetic sequence is characterized by a main vein filling ore stage including quartz, tourmaline, carbonate, and pyrite-hosted gold, chalcopyrite, tellurides, pyrrhotite, and cubanite inclusions. Most of the gold is located in fractures in deformed pyrite and quartz in equilibrium with chalcopyrite and carbonates, with local pyrrhotite, sphalerite, galena, cobaltite, pyrite, or tellurides. Petrography and microthermometry on quartz from the main vein filling ore stage reveal the presence of three unrelated fluid inclusion types: (1) gold-bearing aqueous-carbonic inclusions arranged in three-dimensional intragranular clusters in quartz crystals responsible for the main vein filling stage, (2) barren high-temperature, aqueous, moderately saline inclusions observed in healed fractures, postdating the aqueous-carbonic inclusions, and considered as a remobilizing agent of earlier precipitated gold in late fractures, and (3) barren low-temperature, aqueous, high saline inclusions in healed fractures, similar to the crustal brines reported throughout the Canadian Shield and considered to be unrelated to the gold mineralization. At the Lac Herbin deposit, the aqueous-carbonic inclusions are interpreted to have formed first and to represent the gold-bearing fluid, which were generated contemporaneous with regional greenschist facies metamorphism. In contrast, the high-temperature aqueous fluid dissolved gold from the main vein filling ore stage transported and reprecipitated it in late fractures during a subsequent local thermal event.

  10. Stratigraphy of Karaburun Peninsula

    Directory of Open Access Journals (Sweden)

    Burhan Erdoğan

    1990-06-01

    spanning from Early Triassic to Early Cretaceous, The Balıklıova formation of Campanian-Maastrichtian age rests unconformably, which consists of carbonate rocks and sandstones of flysch facies. The Karaburun belt with the stratigraphy outlined above is surrounded from all sides by a blocky unit which is called the Bomova melange. This blocky unit with highly sheared flysch matrix was formed in the Izmir-Ankara zone during a Maastrichtian-Danian interval. The boundary relations between the Karaburun belt and the Bomova melange indicate that the Karaburun platform was transported tectonically as a nap into the İzmir-Ankara zone during its opening. In this study, we have also found that the stratigraphy of the Karaburun belt is completely different from that of the so-called Sakarya continent, and they cannot be correlated with each other as suggested by the earlier workers.

  11. The composition of fluid inclusions in ore and gangue minerals from the Silesian-Cracow Mississippi Valley-type Zn-Pb deposits Poland: Genetic and environmental implications

    Science.gov (United States)

    Viets, J.G.; Hofstra, A.H.; Emsbo, P.; Kozlowski, A.

    1996-01-01

    The composition of fluids extracted from ore and gangue sulfide minerals that span most of the paragenesis of the Silesian-Cracow district was determined using a newly developed ion chromatographic (IC) technique. Ionic species determined were Na+, NH+4, Ca2+, Mg2+, K+, Rb+, Sr2+, Ba2+, Cl-, Br-, F-, I-, PO3-4, CO2-3, HS-, S2O2-3, SO2-4, NO-3, and acetate. Mineral samples included six from the Pomorzany mine and one from the Trzebionka mine which are hosted in the Triassic Muschelkalk Formation, and two samples of drill core from mineralized Upper Devonian strata. Nine paragenetically identifiable sulfide minerals occur throughout the Silesian-Cracow district. These include from earliest to latest: early iron sulfides, granular sphalerite, early galena, light-banded sphalerite, galena, dark-banded sphalerite, iron sulfides, late dark-banded sphalerite with late galena, and late iron sulfides. Seven of the minerals were sampled for fluid inclusion analysis in this study. Only the early iron sulfides and the last galena stage were not sampled. Although the number of analyses are limited to nine samples and two replicates and there is uncertainty about the characteristics of the fluid inclusions analyzed, the data show clear temporal trends in the composition of the fluids that deposited these minerals. Fluid inclusions in minerals deposited later in the paragenesis have significantly more K+, Br-, NH+4, and acetate but less Sr2+ than those deposited earlier in the paragenesis. The later minerals are also characterized by isotopically lighter sulfur and significantly more Tl and As in the solid minerals. The change in ore-fluid chemistry is interpreted to reflect a major change in the hydrologic regime of the district. Apparently, the migrational paths of ore fluids from the Upper Silesian basin changed during ore deposition and the fluids which deposited early minerals reacted with aquifers with very different geochemical characteristics than those that deposited

  12. Determination of H2O and CO2 concentrations in fluid inclusions in minerals using laser decrepitation and capacitance manometer analysis

    Science.gov (United States)

    Yonover, R. N.; Bourcier, W. L.; Gibson, E. K.

    1985-01-01

    Water and carbon dioxide concentrations within individual and selected groups of fluid inclusions in quartz were analyzed by using laser decrepitation and quantitative capacitance manometer determination. The useful limit of detection (calculated as ten times the typical background level) is about 5 x 10(-10) mol of H2O and 5 x 10(-11) mol of CO2; this H2O content translates into an aqueous fluid inclusion approximately 25 micrometers in diameter. CO2/H2O determinations for 38 samples (100 separate measurements) have a range of H2O amounts of 5.119 x 10(-9) to 1.261 x 10(-7) mol; CO2 amounts of 7.216 x 10(-10) to 1.488 x 10(-8) mol, and CO2/H2O mole ratios of 0.011 to 1.241. Replicate mole ratio determinations of CO2/H2O for three identical (?) clusters of inclusions in quartz have average mole ratios of 0.0305 +/- 0.0041 1 sigma. Our method offers much promise for analysis of individual fluid inclusions, is sensitive, is selective when the laser energy is not so great as to melt the mineral (laser pits approximately 50 micrometers in diameter), and permits rapid analysis (approximately 1 h per sample analysis).

  13. Chemical Compositions of Fluid Inclusions in the Jalal –Abad iron oxide deposit, North West of Zarand, Using LA-ICP-MS Microanalysis

    Directory of Open Access Journals (Sweden)

    Behrouz Karimi Shahraki

    2017-07-01

    Full Text Available Introduction The Poshtebadam Bafq Zarand district in central Iran is a world class iron oxide province. This region contains over two billion tons of iron ore reserves within more than 34 major magnetic anomalies and deposits in an area of 7,500 km2 (Stosch et al., 2011. The Jalal-Abad iron ore deposit (200Mt at 45% Fe, 1.18% S and 0.08% P is located 38 km northwest of Zarand, 16 km southeast of the Rizu town in the Kerman province, Iran. Iron ore deposits are hosted by the Early Cambrian Rizu Series, composed mainly of sedimentary, volcanic and volcaniclastic rocks which are dominated by dolomite, sandstone, shale, siltstone, tuff, ignimbrite and rhyodacite. The origin of the iron oxide deposits is controversial and various genetic models have been suggested. Some researchers believe in magmatic origins or Kiruna type, while others suggest metasomatic replacement from pre-existing rocks (Stosch et al., 2011. LA-ICP-MS has been used to characterize the multi element chemistry of the diverse fluid inclusions found in the Jalal–Abad iron oxide deposit. The aim of this investigation was to understand the genesis of the ore body and identify possible hydrothermal fluid sources in the Jalal-Abad district. Sampling and method of study About 100 samples from different types of ore were collected from surface outcrops and a drill core whose association with mineralization are well established. Thin sections, polished thin sections and polished sections were prepared. SEM studies (FEI 5900LV and LA-ICP-MS analyses of fluid inclusions were carried out in the School of Earth and Environment, the University of Leeds, UK. Fluid inclusions were studied using a Linkam THM-600 heating-freezing stage mounted on Zeiss petrography microscope at the Iranian Mineral Processing Research Center. Result and discussion Jalal Abad deposit is hosted by the early Cambrian volcano-sedimentary rocks of the Rizu series. Stratabound mineralization occurs in a variety of

  14. Calcite Fluid Inclusion, Paragenetic, and Oxygen Isotopic Records of Thermal Event(s) at Yucca Mountain, Nevada

    International Nuclear Information System (INIS)

    Peterman, B.; Moscati, R.

    2000-01-01

    Yucca Mountain, Nevada, is under consideration as a potential high-level radioactive waste repository situated above the water table in 12.7 Ma tuffs. A wealth of textural and geochemical evidence from low-temperature deposits of calcite and silica, indicates that their genesis is related to unsaturated zone (UZ) percolation and that the level of the potential repository has never been saturated. Nonetheless, some scientists contend that thermal waters have periodically risen to the surface depositing calcite and opal in the tuffs and at the surface. This hypothesis received some support in 1996 when two-phase fluid inclusions (FIs) with homogenization temperatures (Th) between 35 and 75 C were reported from UZ calcite. Calcite deposition likely followed closely on the cooling of the tuffs and continues into the present. The paragenetic sequence of calcite and silica in the UZ is early stage calcite followed by chalcedony and quartz, then calcite with local opal during middle and late stages. Four types of FIs are found in calcite assemblages: (1) all-liquid (L); (2) all-vapor (V); (3) 2-phase with large and variable V:L ratios; and (4) a few 2-phase with small and consistent V:L ratios. Late calcite contains no FI assemblages indicating elevated depositional temperatures. In early calcite, the Th of type 4 FIs ranges from ∼ 40 to ∼ 85 C. Such temperatures (sub-boiling) and the assemblage of FIs are consistent with deposition in the UZ. Some delta 18O values < 10 permil in early calcite support such temperatures. Type 4 FIs, however, seem to be restricted to the early calcite stage, during which either cooling of the tuffs or regional volcanism were possible heat sources. Nonetheless, at present there is no compelling evidence of upwelling water as a source for the calcite/opal deposits

  15. New on-line method for water isotope analysis of fluid inclusions in speleothems using laser absorption spectroscopy: Application to stalagmites from Borneo and Switzerland

    Science.gov (United States)

    Affolter, Stéphane; Fleitmann, Dominik; Nele Meckler, Anna; Leuenberger, Markus

    2014-05-01

    Speleothems are recognised as key continental archives for paleoclimate reconstructions. They contain fluid inclusions representing past drip water trapped in the calcite structure. Speleothem can be precisely dated and therefore the oxygen (δ18O) and hydrogen (δD) isotopes of fluid inclusions constitute powerful proxies for paleotemperature or to investigate changes in the moisture source over several interglacial-glacial cycles. To liberate fluid inclusion water and to analyse its isotopic composition, a new online extraction method developed at Bern is used. The principle can be summarised as follows: Prior to crushing, the sample is placed into a copper tube, fixed to the line previously heated to 140° C and flushed with a nitrogen and standard water mixture. Thereafter, the speleothem sample is crushed using a simple hydraulic crushing device and the released water from fluid inclusions is transferred by the nitrogen-standard water mixture flow to a Picarro L1102-i isotopic liquid water and water vapor analyser. The measuring principle is based on wavelength-scanned cavity ring-down spectroscopy (WS-CRDS) technology that allows us to simultaneously monitor hydrogen and oxygen isotopes. Reproducibility of standard water measurements is typically better than 1.5 o for δD and 0.4 o for δ18O. With this method, we successfully analysed δD and δ18O isotopic composition of a stalagmite from Northern Borneo (tropical West Pacific) covering almost two glacial-interglacial cycles from MIS 12 to early MIS 9 (460-330 ka) as well as recent samples from Switzerland and Borneo. These results are used in combination with calcite δ18O to reconstruct paleotemperature. Currently, we are measuring a stalagmite from Milandre cave (Jura, Switzerland) covering the Bølling-Allerød, Younger Dryas cold phase and the Holocene.

  16. Workshop on quantitative dynamic stratigraphy

    Energy Technology Data Exchange (ETDEWEB)

    Cross, T.A.

    1988-04-01

    This document discusses the development of quantitative simulation models for the investigation of geologic systems. The selection of variables, model verification, evaluation, and future directions in quantitative dynamic stratigraphy (QDS) models are detailed. Interdisciplinary applications, integration, implementation, and transfer of QDS are also discussed. (FI)

  17. Evolution and paragenetic context of low δD hydrothermal fluids from the Panasqueira W-Sn deposit, Portugal: new evidence from microthermometric, stable isotope, noble gas and halogen analyses of primary fluid inclusions

    Science.gov (United States)

    Polya, D. A.; Foxford, K. A.; Stuart, F.; Boyce, A.; Fallick, A. E.

    2000-10-01

    The evolution, paragenetic context and origin of remarkably low δD hydrothermal fluids from the Hercynian Panasqueira W-Sn-Cu(Ag) deposit have been investigated through a combined microthermometric, stable isotope, halogen and noble gas fluid inclusion study. Large variations in δD between -60 ‰ and -134‰ have been observed in primary fluid inclusions from growth zones in a quartz crystal (Pa66) paragenetically constrained to the main sulfide stage (MSS) of ore formation. The same fluids exhibited relatively constant fluid inclusion homogenisation temperatures (254 to 260°C), salinities (7.4 to 8.7 wt.% NaCl equivalent) and calculated fluid δ 18O (3.8 to 4.4‰). All the fluids exhibited 40Ar excesses. Mean molar Br/Cl and I/Cl ratios varied from 2.3 × 10 -3-4.2 × 10 -3 and 8 × 10 -4-10 × 10 -4 respectively, with the more Br-rich fluids being associated with the more deuterium-depleted fluids. The low palaeolatitude of Panasqueira throughout the main stages of ore formation and the overwhelming predominance of meteoric fluids in the main, late and post-ore mineralising fluids with δD of -40 to -65‰ lends little support for any models involving low δD palaeometeoric water. The limited range of 40Ar∗/Cl ratios (1.1 × 10 -5-1.6 × 10 -5) also precludes boiling during the MSS or mixing of meteoric water with highly fractionated deuterium-depleted magmatic waters as viable mechanisms for producing the low δD fluids. The high Br/Cl and I/Cl of the MSS fluids indicate significant fluid interactions with organic rich sediments or metasediments, in particular regionally abundant Carboniferous coals or coaly sediments that are inferred to be depleted in deuterium by around 85‰ compared to palaeometeoric water. The large range of δD observed in the MSS fluids may be explained by isotopic exchange of palaeometeoric water with these coals at varying water/rock (wt./wt.) ratios between 0.02 and 0.002 with fluid oxygen isotopic compositions controlled by

  18. The origin of the Tongkeng-Changpo tin deposit, Dachang metal district, Guangxi, China: clues from fluid inclusions and He isotope systematics

    Science.gov (United States)

    Minghai, Cai; Jingwen, Mao; Ting, Liang; Pirajno, Franco; Huilan, Huang

    2007-08-01

    Tongkeng-Changpo is the largest tin deposit within the giant Dachang polymetallic tin ore field in Guangxi, southern China, which is part of a large skarn system associated with Cretaceous granitoids. The Tongkeng-Changpo mineralization consists of veins and stockworks in the upper levels and replacement stratiform orebodies (mantos) at lower levels. Based on textural relationships, three major mineralizing stages can be recognized: stage I with cassiterite, sulphides, stannite, tourmaline, and quartz; stage II with cassiterite, sulphides, sulphosalts, quartz, and calcite; and stage III with calcite as the main phase. The study of fluid inclusions has shown that there are two main fluid types: CO2 and NaCl-H2O. Homogenization temperatures are 270 to 365°C, 210 to 240°C, and 140 to 190°C for stages I, II, and III, respectively. Salinities range from 1 to 7 wt.% NaCl equiv. in the early ore stage and 3 to 10 wt.% NaCl equiv. in the late stages. Laser Raman Spectroscopy indicates that the inclusion fluids in stages I and II were of carbono-aqueous composition, with minor amounts of CH4 and H2S, whereas those in stage III were aqueous. Helium isotopic analyses of inclusion fluids indicate that the 3He/4He ratios in the ore veins are in between 1.2 to 2.9 Ra (Ra = 1.4 × 10-6, modern atmospheric ratio), and range from 1.6 to 2.5 Ra in the stratiform orebodies. This range of 3He/4He ratios is significantly higher than that of crustal fluids (0.01-0.05 Ra). The similar characteristics of fluid inclusions and their He isotopic composition, as well as age constraints, indicate that the ore veins and stratiform orebodies of the Tongkeng-Changpo deposit formed from the same hydrothermal system, likely related to granite intrusions of the Mesozoic Yanshanian tectono-thermal event. In addition, the high R/Ra ratios indicate a mantle contribution in the ore fluids.

  19. Raman spectroscopic measurements of CO2 density: Experimental calibration with high-pressure optical cell (HPOC) and fused silica capillary capsule (FSCC) with application to fluid inclusion observations

    Science.gov (United States)

    Wang, X.; Chou, I-Ming; Hu, W.; Burruss, Robert; Sun, Q.; Song, Y.

    2011-01-01

    Raman spectroscopy is a powerful method for the determination of CO2 densities in fluid inclusions, especially for those with small size and/or low fluid density. The relationship between CO2 Fermi diad split (Δ, cm−1) and CO2 density (ρ, g/cm3) has been documented by several previous studies. However, significant discrepancies exist among these studies mainly because of inconsistent calibration procedures and lack of measurements for CO2fluids having densities between 0.21 and 0.75 g/cm3, where liquid and vapor phases coexist near room temperature.In this study, a high-pressure optical cell and fused silica capillary capsules were used to prepare pure CO2 samples with densities between 0.0472 and 1.0060 g/cm3. The measured CO2 Fermi diad splits were calibrated with two well established Raman bands of benzonitrile at 1192.6 and 1598.9 cm−1. The relationship between the CO2 Fermi diad split and density can be represented by: ρ = 47513.64243 − 1374.824414 × Δ + 13.25586152 × Δ2 − 0.04258891551 × Δ3(r2 = 0.99835, σ = 0.0253 g/cm3), and this relationship was tested by synthetic fluid inclusions and natural CO2-rich fluid inclusions. The effects of temperature and the presence of H2O and CH4 on this relationship were also examined.

  20. Origin of the Okrouhlá Radouň episyenite-hosted uranium deposit, Bohemian Massif, Czech Republic: fluid inclusion and stable isotope constraints

    Science.gov (United States)

    Dolníček, Zdeněk; René, Miloš; Hermannová, Sylvie; Prochaska, Walter

    2014-04-01

    The Okrouhlá Radouň shear zone hosted uranium deposit is developed along the contact of Variscan granites and high-grade metasedimentary rocks of the Moldanubian Zone of the Bohemian Massif. The pre-ore pervasive alteration of wall rocks is characterized by chloritization of mafic minerals, followed by albitization of feldspars and dissolution of quartz giving rise to episyenites. The subsequent fluid circulation led to precipitation of disseminated uraninite and coffinite, and later on, post-ore quartz and carbonate mineralization containing base metal sulfides. The fluid inclusion and stable isotope data suggest low homogenization temperatures (˜50-140 °C during pre-ore albitization and post-ore carbonatization, up to 230 °C during pre-ore chloritization), variable fluid salinities (0-25 wt.% NaCl eq.), low fluid δ18O values (-10 to +2 ‰ V-SMOW), low fluid δ13C values (-9 to -15 ‰ V-PDB), and highly variable ionic composition of the aqueous fluids (especially Na/Ca, Br/Cl, I/Cl, SO4/Cl, NO3/Cl ratios). The available data suggest participation of three fluid endmembers of primarily surficial origin during alteration and mineralization at the deposit: (1) local meteoric water, (2) Na-Ca-Cl basinal brines or shield brines, (3) SO4-NO3-Cl-(H)CO3 playa-like fluids. Pre-ore albitization was caused by circulation of alkaline, oxidized, and Na-rich playa fluids, whereas basinal/shield brines and meteoric water were more important during the post-ore stage of alteration.

  1. Mineralogy, fluid inclusion petrography, and stable isotope geochemistry of Pb-Zn-Ag veins at the Shizhuyuan deposit, Hunan Province, southeastern China

    Science.gov (United States)

    Wu, Shenghua; Mao, Jingwen; Yuan, Shunda; Dai, Pan; Wang, Xudong

    2018-01-01

    The Shizhuyuan polymetallic deposit is located in the central part of the Nanling region, southeastern China, and consists of proximal W-Sn-Mo-Bi skarns and greisens and distal Pb-Zn-Ag veins. The sulfides and sulfosalts in the distal veins formed in three distinct stages: (1) an early stage of pyrite and arsenopyrite, (2) a middle stage of sphalerite and chalcopyrite, and (3) a late stage of galena, Ag-, Sn-, and Bi-bearing sulfides and sulfosalts, and pyrrhotite. Combined sulfide and sulfosalt geothermometry and fluid inclusion analyses indicate that the early stage of mineralization occurred at a temperature of 400 °C and involved boiling under hydrostatic pressure ( 200 bar), with the temperature of the system dropping during the late stage to 200 °C. Laser Raman analysis indicates that the fluid inclusions within the studied minerals are dominated by H2O, although some contain carbonate solids and CH4 gas. Vein-hosted sulfides have δ34S values of 3.8-6.3‰ that are interpreted as indicative of a magmatic source of sulfur. The mineralization process can be summarized as follows: an aqueous fluid exsolved on final crystallization of the Qianlishan pluton, ascended along fracture zones, cooled to fugacity, sulfide and sulfosalt minerals precipitated successively from the Ag-Cu-Zn-Fe-Pb-Sb-As-S-bearing fluid system.

  2. Recovery Act. Sub-Soil Gas and Fluid Inclusion Exploration and Slim Well Drilling, Pumpernickel Valley, Nevada

    Energy Technology Data Exchange (ETDEWEB)

    Fairbank, Brian D. [Nevada Geothermal Power Company, Las Vegas, NV (United States)

    2015-03-27

    Nevada Geothermal Power Company (NGP) was awarded DOE Award DE-EE0002834 in January 2010 to conduct sub-soil gas and fluid inclusion studies and slim well drilling at its Black Warrior Project (now known as North Valley) in Washoe and Churchill Counties, Nevada. The project was designed to apply highly detailed, precise, low-cost subsoil and down-hole gas geochemistry methods from the oil and gas industry to identify upflow zone drilling targets in an undeveloped geothermal prospect. NGP ran into multiple institutional barriers with the Black Warrior project relating to property access and extensive cultural survey requirement. NGP requested that the award be transferred to NGP’s Pumpernickel Valley project, due to the timing delay in obtaining permits, along with additional over-budget costs required. Project planning and permit applications were developed for both the original Black Warrior location and at Pumpernickel. This included obtaining proposals from contractors able to conduct required environmental and cultural surveying, designing the two-meter probe survey methodology and locations, and submitting Notices of Intent and liaising with the Bureau of Land Management to have the two-meter probe work approved. The award had an expiry date of April 30, 2013; however, due to the initial project delays at Black Warrior, and the move of the project from Black Warrior to Pumpernickel, NGP requested that the award deadline be extended. DOE was amenable to this, and worked with NGP to extend the deadline. However, following the loss of the Blue Mountain geothermal power plant in Nevada, NGP’s board of directors changed the company’s mandate to one of cash preservation. NGP was unable to move forward with field work on the Pumpernickel property, or any of its other properties, until additional funding was secured. NGP worked to bring in a project partner to form a joint venture on the property, or to buy the property. This was unsuccessful, and NGP notified

  3. Scientific results from the deepened Lopra-1 borehole, Faroe Islands: A reconnaissance study of fluid inclusions in fracture-filling quartz and calcite from the Lopra-1/1A well, Faroe Islands

    Directory of Open Access Journals (Sweden)

    Konnerup-Madsen, Jens

    2006-07-01

    Full Text Available Fracture-filling calcite and quartz from the Lopra-1/1A well (at 2380 m and 3543 m depth contains both aqueous low-salinity fluid inclusions and hydrocarbon-dominated fluid inclusions. Microthermometry indicates that the aqueous fluids contain 0.2 to 1.4 equivalent weight% NaCl and occasionally contain traces of hydrocarbons. Homogenisation to liquid occurred between 90°C and 150°C. Modelling based on these fluid inclusion observations indicates that during burial the basaltic section was subjected to temperatures of 160°C and 170°C, occasional pressures of 600–700 bars and the simultaneous percolation of aqueous and hydrocarbon fluids. These fluid conditions may also be relevant to the formation of zeolite observed in the Lopra-1/1A well.

  4. Investigating fossil hydrothermal systems by means of fluid inclusions and stable isotopes in banded travertine: an example from Castelnuovo dell'Abate (southern Tuscany, Italy)

    Science.gov (United States)

    Rimondi, Valentina; Costagliola, Pilario; Ruggieri, Giovanni; Benvenuti, Marco; Boschi, Chiara; Brogi, Andrea; Capezzuoli, Enrico; Morelli, Guia; Gasparon, Massimo; Liotta, Domenico

    2016-03-01

    Southern Tuscany (Italy) hosts geothermal anomalies with associated widespread CO2 gas-rich manifestations and active travertine-deposing thermal springs. Geothermal anomalies have been active since the Late Miocene and have led to the formation of widespread Late Miocene-Pleistocene travertine deposits and meso- and epithermal mineralizations. This study investigates the travertine deposit exposed in the Castelnuovo dell'Abate area of southern Tuscany. Here, a fissure-ridge type travertine deposit and its feeding conduits, currently filled with banded calcite veins (i.e. banded travertine), represent a spectacular example of fossil hydrothermal circulation in the peripheral area of the exploited Monte Amiata geothermal field. The Castelnuovo dell'Abate travertine deposit and associated calcite veins were analysed to establish the characteristics of the parent hydrothermal fluids, and the age of this circulation. The focus of the study was on fluid inclusions, rarely considered in travertine studies, but able to provide direct information on the physico-chemical characteristics of the original fluid. Uranium-thorium geochronological data provided further constraints on the: (1) age of tectonic activity; (2) age of the hydrothermal circulation; and (3) evolution of the Monte Amiata geothermal anomaly. Results indicate that brittle deformation (NW- and SE-trending normal to oblique-slip faults) was active during at least the Middle Pleistocene and controlled a hydrothermal circulation mainly characterized by fluids of meteoric origin, and as old as 300-350 ka. This is the oldest circulation documented to date in the Monte Amiata area. The fluid chemical composition is comparable to that of fluids currently exploited in the shallow reservoir of the Monte Amiata geothermal field, therefore suggesting that fluid composition has not changed substantially over time. These fluids, however, have cooled by about 70 °C in the last 300-350 ka, corresponding to a cooling rate

  5. Geology, mineralization, and fluid inclusion study of the Kuru-Tegerek Au-Cu-Mo skarn deposit in the Middle Tien Shan, Kyrgyzstan

    Science.gov (United States)

    Soloviev, Serguei G.; Kryazhev, Sergey; Dvurechenskaya, Svetlana

    2018-02-01

    The Kuru-Tegerek Cu-Au-Mo deposit is situated in a system of Late Carboniferous subduction-related magmatic arcs of the Middle Tien Shan, which together constitute a metallogenic belt of Cu-Au-Mo (±W) porphyry, with local skarns, deposits. The deposit is related to magnetite-series gabbro-diorite to tonalite intrusion. It contains prograde magnesian and calcic skarns with abundant magnetite, associated with gabbro-diorite, and retrograde skarn with Cu mineralization, formed after intrusion of tonalite. Subsequent propylitic alteration introduced abundant chalcopyrite and pyrrhotite, and native Au culminating in zones overprinting magnetite and garnet skarn. Later quartz-muscovite-carbonate veins, formed after intrusion of late mafic quartz monzogabbro dikes, contain chalcopyrite, pyrite, arsenopyrite and other sulfides and sulfosalts, tellurides, and native Au. The earliest retrograde skarn garnet contains gaseous low-salinity (1.7-3.4 wt.% NaCl eq.) fluid inclusions homogenizing at 460-500 °C into vapor, indicating that the early fluid released from crystallizing magma was a low-density vapor. It was followed by more saline (4.0-5.0 wt.% NaCl eq.), high-temperature (400-440 °C) aqueous fluid, as fluid release from the magma progressed. Boiling of this fluid at temperatures of 420 to 370 °C and a pressure of 350-300 bar produced a low-salinity (0.6-1.2 wt.% NaCl eq.), essentially gaseous, and high-salinity (from 39 to 31 wt.% NaCl eq.) brine, with possible metal (including Cu) partitioning into both gaseous and aqueous-saline phases. Boiling was coeval with sulfide deposition in the retrograde skarn. The latest episode of the retrograde skarn stage included direct separation of saline ( 40-42 wt.% NaCl eq.) fluid from crystallizing magma. The separation of saline ( 40 to 14 wt.% NaCl eq.) fluids from a crystallizing magmatic melt continued during the propylitic stage, when fluid cooling from 370 to 320 °C, together with decreasing fO2, caused Cu and especially

  6. A salt diapir-related Mississippi Valley-type deposit: The Bou Jaber Pb-Zn-Ba-F deposit, Tunisia: Fluid inclusion and isotope study

    Science.gov (United States)

    Bouhlel, Salah; Leach, David; Johnson, Craig A.; Marsh, Erin; Salmi-Laouar, Sihem; Banks, David A.

    2016-01-01

    The Bou Jaber Ba-F-Pb-Zn deposit is located at the edge of the Bou Jaber Triassic salt diapir in the Tunisia Salt Diapir Province. The ores are unconformity and fault-controlled and occur as subvertical column-shaped bodies developed in dissolution-collapse breccias and in cavities within the Late Aptian platform carbonate rocks, which are covered unconformably by impermeable shales and marls of the Fahdene Formation (Late Albian–Cenomanian age). The host rock is hydrothermally altered to ankerite proximal to and within the ore bodies. Quartz, as fine-grained bipyramidal crystals, formed during hydrothermal alteration of the host rocks. The ore mineral assemblage is composed of barite, fluorite, sphalerite, and galena in decreasing abundance. The ore zones outline distinct depositional events: sphalerite-galena, barite-ankerite, and fluorite. Fluid inclusions, commonly oil-rich, have distinct fluid salinities and homogenization temperatures for each of these events: sphalerite-galena (17 to 24 wt% NaCl eq., and Th from 112 to 136 °C); ankerite-barite (11 to 17 wt% NaCl eq., and Th from 100 to 130 °C); fluorite (19 to 21 wt% NaCl eq., Th from 140 to 165 °C). The mean temperature of the ore fluids decreased from sphalerite (125 °C) to barite (115 °C) and increased during fluorite deposition (152 °C); then decreased to ∼110 °C during late calcite precipitation. Laser ablation inductively coupled plasma mass spectrometry (LA-ICP-MS) analyses of fluid inclusions in fluorite are metal rich (hundreds to thousands ppm Pb, Zn, Cu, Fe) but the inclusions in barite are deficient in Pb, Zn, Cu, Fe. Inclusions in fluorite have Cl/Br and Na/Br ratios of several thousand, consistent with dissolution of halite while the inclusions analysed in barite have values lower than seawater which are indicative of a Br-enriched brine derived from evaporation plus a component of halite dissolution. The salinity of the barite-hosted fluid inclusions is less than obtained

  7. A salt diapir-related Mississippi Valley-type deposit: the Bou Jaber Pb-Zn-Ba-F deposit, Tunisia: fluid inclusion and isotope study

    Science.gov (United States)

    Bouhlel, Salah; Leach, David L.; Johnson, Craig A.; Marsh, Erin; Salmi-Laouar, Sihem; Banks, David A.

    2016-08-01

    The Bou Jaber Ba-F-Pb-Zn deposit is located at the edge of the Bou Jaber Triassic salt diapir in the Tunisia Salt Diapir Province. The ores are unconformity and fault-controlled and occur as subvertical column-shaped bodies developed in dissolution-collapse breccias and in cavities within the Late Aptian platform carbonate rocks, which are covered unconformably by impermeable shales and marls of the Fahdene Formation (Late Albian-Cenomanian age). The host rock is hydrothermally altered to ankerite proximal to and within the ore bodies. Quartz, as fine-grained bipyramidal crystals, formed during hydrothermal alteration of the host rocks. The ore mineral assemblage is composed of barite, fluorite, sphalerite, and galena in decreasing abundance. The ore zones outline distinct depositional events: sphalerite-galena, barite-ankerite, and fluorite. Fluid inclusions, commonly oil-rich, have distinct fluid salinities and homogenization temperatures for each of these events: sphalerite-galena (17 to 24 wt% NaCl eq., and Th from 112 to 136 °C); ankerite-barite (11 to 17 wt% NaCl eq., and Th from 100 to 130 °C); fluorite (19 to 21 wt% NaCl eq., Th from 140 to 165 °C). The mean temperature of the ore fluids decreased from sphalerite (125 °C) to barite (115 °C) and increased during fluorite deposition (152 °C); then decreased to ˜110 °C during late calcite precipitation. Laser ablation inductively coupled plasma mass spectrometry (LA-ICP-MS) analyses of fluid inclusions in fluorite are metal rich (hundreds to thousands ppm Pb, Zn, Cu, Fe) but the inclusions in barite are deficient in Pb, Zn, Cu, Fe. Inclusions in fluorite have Cl/Br and Na/Br ratios of several thousand, consistent with dissolution of halite while the inclusions analysed in barite have values lower than seawater which are indicative of a Br-enriched brine derived from evaporation plus a component of halite dissolution. The salinity of the barite-hosted fluid inclusions is less than obtained simply by the

  8. Systematic sulfur stable isotope and fluid inclusion studies on veinlet groups in the Sarcheshmeh porphyry copper deposit: based on new data

    Directory of Open Access Journals (Sweden)

    Mohammad Maanijou

    2012-10-01

    Full Text Available Mineralization occurred by intrusion of granodioritic stock of middle Miocene in volcano–sedimenrary rocks in Sarcheshmeh of early Tertiary age. This research is based on samples of new drilled boreholes and benches of 2500m elevation. Based on mineralogy and crosscutting relationships, at least four groups of veinlets pertaining to four stages of mineralization were recognized. Sulfur isotope studies in the Sarcheshmeh porphyry copper deposit were conducted on pyrite, chalcopyrite, molybdenite and anhydrites of four groups of veinlets. The δ34S values in the sulfides and sulfates range from -2.2 to 1.27‰ and from 10.2 to 14.5 ‰, respectively. The average δ34S value in the sulfides is 1‰ and that for the sulfates is about 13‰. Considering these results, it can be concluded that the sulfides made up of a fluid that its sulfur has a magmatic origin. Also, fluid inclusions of different veinlet groups were studied, showing high temperature, high salinity and the occurrence of boiling in the mineralizing fluids. Moreover, these studies indicate presence of three types of fluids including magmatic, meteoritic and mixture of these two fluids in alteration and mineralizion processes.

  9. The genesis of the Hashitu porphyry molybdenum deposit, Inner Mongolia, NE China: constraints from mineralogical, fluid inclusion, and multiple isotope (H, O, S, Mo, Pb) studies

    Science.gov (United States)

    Zhai, Degao; Liu, Jiajun; Tombros, Stylianos; Williams-Jones, Anthony E.

    2018-03-01

    The Hashitu porphyry molybdenum deposit is located in the Great Hinggan Range Cu-Mo-Pb-Zn-Ag polymetallic metallogenic province of NE China, in which the Mo-bearing quartz veins are hosted in approximately coeval granites and porphyries. The deposit contains more than 100 Mt of ore with an average grade of 0.13 wt.% Mo. This well-preserved magmatic-hydrothermal system provides an excellent opportunity to determine the source of the molybdenum, the evolution of the hydrothermal fluids and the controls on molybdenite precipitation in a potentially important but poorly understood metallogenic province. Studies of fluid inclusions hosted in quartz veins demonstrate that the Hashitu hydrothermal system evolved to progressively lower pressure and temperature. Mineralogical and fluid inclusion analyses and physicochemical calculations suggest that molybdenite deposition occurred at a temperature of 285 to 325 °C, a pressure from 80 to 230 bars, a pH from 3.5 to 5.6, and a Δlog fO2 (HM) of -3.0, respectively. Results of multiple isotope (O, H, S, Mo, and Pb) analyses are consistent in indicating a genetic relationship between the ore-forming fluids, metals, and the Mesozoic granitic magmatism (i.e., δ 18OH2O from +1.9 to +9.7‰, δDH2O from -106 to -87‰, δ 34SH2S from +0.3 to +3.9‰, δ 98/95Mo from 0 to +0.37‰, 206Pb/204Pb from 18.2579 to 18.8958, 207Pb/204Pb from 15.5384 to 15.5783, and 208Pb/204Pb from 38.0984 to 42.9744). Molybdenite deposition is interpreted to have occurred from a low-density magmatic-hydrothermal fluid in response to decreases in temperature, pressure, and fO2.

  10. Fluid inclusion and vitrinite-reflectance geothermometry compared to heat-flow models of maximum paleotemperature next to dikes, western onshore Gippsland Basin, Australia

    Science.gov (United States)

    Barker, C.E.; Bone, Y.; Lewan, M.D.

    1999-01-01

    Nine basalt dikes, ranging from 6 cm to 40 m thick, intruding the Upper Jurassic-Lower Cretaceous Strzelecki Group, western onshore Gippsland Basin, were used to study maximum temperatures (Tmax) reached next to dikes. Tmax was estimated from fluid inclusion and vitrinitereflectance geothermometry and compared to temperatures calculated using heat-flow models of contact metamorphism. Thermal history reconstruction suggests that at the time of dike intrusion the host rock was at a temperature of 100-135??C. Fracture-bound fluid inclusions in the host rocks next to thin dikes ( 1.5, using a normalized distance ratio used for comparing measurements between dikes regardless of their thickness. In contrast, the pattern seen next to the thin dikes is a relatively narrow zone of elevated Rv-r. Heat-flow modeling, along with whole rock elemental and isotopic data, suggests that the extended zone of elevated Rv-r is caused by a convection cell with local recharge of the hydrothermal fluids. The narrow zone of elevated Rv-r found next to thin dikes is attributed to the rise of the less dense, heated fluids at the dike contact causing a flow of cooler groundwater towards the dike and thereby limiting its heating effects. The lack of extended heating effects suggests that next to thin dikes an incipient convection system may form in which the heated fluid starts to travel upward along the dike but cooling occurs before a complete convection cell can form. Close to the dike contact at X/D 1.5. ?? 1998 Elsevier Science B.V. All rights reserved.

  11. Evidence for a hypogene paleohydrogeological event at the prospective nuclear waste disposal site Yucca Mountain, Nevada, USA, revealed by the isotope composition of fluid-inclusion water

    Science.gov (United States)

    Dublyansky, Yuri V.; Spötl, Christoph

    2010-01-01

    Secondary calcite residing in open cavities in the unsaturated zone of Yucca Mountain has long been interpreted as the result of downward infiltration of meteoric water through open fractures. In order to obtain information on the isotopic composition (δD and δ 18O) of the mineral-forming water we studied fluid inclusions from this calcite. Water was extracted from inclusions by heated crushing and the δD values were measured using a continuous-flow isotope-ratio mass spectrometry method. The δ 18O values were calculated from the δ 18O values of the host calcite assuming isotopic equilibrium at the temperature of formation determined by fluid-inclusion microthermometry. The δD values measured in all samples range between - 110 and - 90‰, similar to Holocene meteoric water. Coupled δ 18O-δD values plot significantly, 2 to 8‰, to the right of the meteoric water line. Among the various processes operating at the topographic surface and/or in the unsaturated zone only two processes, evaporation and water-rock exchange, could alter the isotope composition of percolating water. Our analysis indicates, however, that none of these processes could produce the observed large positive δ 18O-shifts. The latter require isotopic interaction between mineral-forming fluid and host rock at elevated temperature (>100 °C), which is only possible in the deep-seated hydrothermal environment. The stable isotope data are difficult to reconcile with a meteoric origin of the water from which the secondary minerals at Yucca Mountain precipitated; instead they point to the deep-seated provenance of the mineral-forming waters and their introduction into the unsaturated zone from below, i.e. a hypogene origin.

  12. The genesis of the amethyst geodes at Artigas (Uruguay) and the paleohydrology of the Guaraní aquifer: structural, geochemical, oxygen, carbon, strontium isotope and fluid inclusion study

    Science.gov (United States)

    Morteani, Giulio; Kostitsyn, Y.; Preinfalk, C.; Gilg, H. A.

    2010-06-01

    The amethyst-bearing geodes found in the flood basalts of the Arapey formation at Artigas (Uruguay) were formed as protogeodes by bubbles of CO2-rich basalt-derived fluids. The formation of the celadonite rim and the lining of the geodes by agate followed by quartz and amethyst were driven by the artesian water of the Guaraní aquifer percolating the basalts from below. The temperature of the amethyst formation is estimated from fluid inclusion data to be between 50° and 120°C. Oxygen stable isotope data suggest a crystallization temperature of calcite of about only 24°C. The actual wellhead temperature of the water produced from the Guaraní aquifer in the study area is around 29°C.

  13. Invisible gold distribution on pyrite and ore-forming fluid process of the Huangshan orogenic-type gold deposit of Zhejiang, SE China: implications from mineralogy, trace elements, impurity and fluid inclusion studies

    Science.gov (United States)

    Sundarrajan, Vijay Anand; Li, Zilong; Hu, Yizhou; Fu, Xuheng; Zhu, Yuhuo

    2017-04-01

    The Huangshan orogenic-type gold deposit in Zhejiang of SE China occurred in quartz-pyrite veins. It is hosted by phyllonite that underwent greenschist-facies metamorphism along a large Jiangshan-Shaoxing tectonic belt with a NE-SW direction. Trace elemental characteristics, ore-forming process and invisible gold on different forms of pyrite and quartz are studied. The Au associated pyrite can be classified into two categories; recrystallized pyrite and euhedral pyrite. The precipitation of invisible Au on pyrite is mainly derived by Co and Ni with AuHS2 - complex in the mineralizing fluids in different events. The XPS results revealed that valence states of Au3+ replaced 2Fe2+ in the pyrite and Au0 replaced Si4+ in the quartz structure. The electron paramagnetic resonance and trace elemental results suggested that the element pairs of Ge-Li-Al in quartz and Mn-Co-Ni in pyrite have distinct impurities as identified. A fluid inclusion study showed that the auriferous quartz is characterized by low-saline and CO2-rich fluids. Coexistence of the type I-type III inclusions and same range of homogenization temperature with different mode are evidences of immiscible fluid process. The temperature-pressure values of ca. 250 °C/1250 bar and ca. 220 °C/780 bar for gold precipitation have been calculated by intersection of coexisting fluids during the entrapment. The Huangshan orogenic-type gold deposit may be associated with the Wuyi-Yunkai orogeny during the early Paleozoic, including an upper-mid greenschist-facies metamorphism (450-420 Ma). All the features suggest that the Huangshan gold deposit is probably a product linking with the early Paleozoic orogeny in South China.

  14. Fluid inclusions in minerals associated to uranium mineralization in Jazida do Engenho (anomaly 09), Lagoa Real uranium province - Bahia, Brazil

    International Nuclear Information System (INIS)

    Souza, Aurelio da Silva de

    2009-01-01

    The Engenho deposit (anomaly 09) is south-eastern from Cachoeira Mine (anomaly 13), in the northern part of the Province. The uranium mineralization is associated to 'albitites' (over 70% of albite/oligoclase). Epidosites with uranium may also occur. The 'albitite' main minerals are pyroxene, gamet, albite/oligoclase feldspar, amphibole and biotite. Pyroxene, gamet, plagioclase, titanite and epidote are the minerals associated to the uranium mineralization. The fluids related to pyroxene, gamet and epidote are aqueous-saline, primary and with no carbonic phases and are constant, with small variations. They all present medium to high salinity (14 to 18wt% NaCl eq.), the higher values being related to pyroxene and the lower ones related to gamet and epidote. The fluids associated to albite/oligoclase, although aqua-saline and with no carbonic phases, show salinities much lower than in pyroxene, gamet and epidote, suggesting a intense dilution process indicating dilution toward the later minerals phases. The data suggest the pyroxene formation process occurring under a 3,5 kbar pressure condition which corresponds to approximately 10km depth. The dispersion on Th in albites, due probably to the overheating and non elastic increase in volume, precluded a reliable pressure calculation. The IF's microscopy m plagioclase gneiss (albitites host-rocks) suggests the probability of primary carbonic fluids associated to these minerals. The fluids with CO 2 showed in the gneiss maybe also be present in the albitites, probably as late or intergranular fluids. This assumption is based on the fact that signs of carbonic gases were shown during crushing tests. These tendencies suggest the occurrence of two albitization phases in this Lagoa Real area: one associated to a fluid composed by H 2 O + CO 2 + salts (in the gneiss host) and another (in the albitite) formed by an aqueous-saline phase. The data indicate the Brasiliano event as a thermal event without a predominant fluid

  15. Experimental petrology for the thermobarometric determination of mineral paragenesis: the fluid inclusions; Petrologia experimental para la determinacion termobarometrica de paragenesis minerales: las inclusiones fluidas

    Energy Technology Data Exchange (ETDEWEB)

    Gonzalez Partida, Eduardo; Torres Rodriguez, Vicente; Birkle, Peter [Instituto de Investigaciones Electricas, Cuernavaca (Mexico)

    1994-05-01

    There is a great number of phenomena in nature in which some fluid participates as the main component. Such is the case of oil deposits formation, of metallic minerals, geothermal systems, metamorphic and diagenetic deposits. The common denominator of all of them is that in some part of their stages important physico-chemical processes occurred in the related fluids, leaving evidence of such phenomena in the fluid inclusions. The Geothermal Department has petrologic vanguard tools for reservoir problems resolution, since it has laboratories for the study on fluid inclusions by means of the technique called cryoscopic-microthermometry that permits the definition of physico-chemical conditions of the brine that participated or participates in the hydrothermal systems formation. The method simultaneously permits to know the characteristics of the initial brine that participated in the interaction water-rock phenomenon, observe the boiling phenomena, and determine conditions of initial pressure in the reservoirs. [Espanol] Existe un gran numero de fenomenos en la naturaleza en los que participa algun fluido como componente principal. Tal es el caso de la formacion de yacimientos de petroleo, de minerales metalicos, de sistemas geotermicos, yacimientos metamorficos y diageneticos. El comun denominador de todos ellos es que en alguna de sus etapas ocurrieron procesos fisicoquimicos importantes en los fluidos relacionados, quedando evidencia de tales fenomenos en las inclusiones fluidas. El Departamento de Geotermia cuenta con herramientas petrologicas de vanguardia para la resolucion de problemas en yacimientos, ya que tiene laboratorios para el estudio de las inclusiones fluidas por medio de la tecnica denominada microtermometria-crioscopica que permite definir condiciones fisicoquimicas de la salmuera que participo o participa en la formacion de sistemas hidrotermales. El metodo permite simultaneamente conocer las caracteristicas de la salmuera inicial que participo en

  16. Hydrothermal Evolution of the Giant Cenozoic Kadjaran porphyry Cu-Mo deposit, Tethyan metallogenic belt, Armenia, Lesser Caucasus: mineral paragenetic, cathodoluminescence and fluid inclusion constraints

    Science.gov (United States)

    Hovakimyan, Samvel; Moritz, Robert; Tayan, Rodrik; Rezeau, Hervé

    2016-04-01

    stockwork. One of them is the east-west-oriented 6th vein zone in the northern part of the deposit, which contains quartz-molybdenite veins and late quartz-galena-sphalerite veins. This is interpreted as a telescoping between porphyry and epithermal environments. It is supported by microscopic studies of mineral paragenesis, which reveal the presence of enargite and tennantite-tetrahedrite, luzonite, sphalerite, and galena, generally in a gangue of quartz, followed by a late carbonate and gypsum stage. On-going fluid inclusion studies are being carried out on quartz samples from the different mineralization stages. Five types of fluid inclusions were distinguished according to their nature, bubble size, and daughter mineral content: vapor-rich, aqueous-carbonic, brine, polyphase brine and liquid-rich inclusions. Cathodoluminescence images from the porphyry veins reveal four generations of quartz. Molybdenite and chalcopyrite are associated with two different dark luminescent quartz generations, which contain typical brine, aqueous-carbonic and vapour-rich H2O fluid inclusions, with some of them coexisting locally as boiling assemblages. Epithermal veins are mainly characterized by liquid-rich H2O fluid inclusions. Microthermometric studies of fluid inclusions reveal a major difference in homogenisation temperatures between the early quartz-molybdenite- chalcopyrite stage (Thtotal between 3600 and 4250C) and the late quartz-galena-sphalerite vein stage (Thtotal 300-2700C), which is attributed to the transition from a porphyry to an epithermal environment in the Kadjaran deposit.

  17. Technical Note: How accurate can stalagmite formation temperatures be determined using vapour bubble radius measurements in fluid inclusions?

    DEFF Research Database (Denmark)

    Spadin, F.; Marti, Dominik; Hidalgo-Staub, R.

    2015-01-01

    -induced vapour bubbles inside the inclusions. A reliable method for precisely measuring the radius of vapour bubbles is presented. The method is applied to stalagmite samples for which the formation temperature is known. An assessment of the bubble radius measurement accuracy and how this error influences......-of-principle investigation that the formation temperature of 10–20 yr old inclusions in a stalagmite taken from the Milandre cave is 9.87 ± 0.80 ◦C, while the mean annual surface temperature, that in the case of the Milandre cave correlates well with the cave temperature, was 9.6 ± 0.15 ◦C, calculated from actual...... measurements at that time, showing a very good agreement. Formation temperatures of inclusions formed during the last 450 yr are found in a temperature range between 8.4 and 9.6 ◦C, which corresponds to the calculated average surface temperature. Paleotemperatures can thus be determined within ±1.0 ◦C....

  18. Fluid Inclusion Study of Quartz Xenocrysts in Mafic Dykes from Kawant Area, Chhota Udaipur District, Gujarat, India

    OpenAIRE

    Randive Kirtikumar; Hurai Vratislav

    2015-01-01

    Unusual mafic dykes occur in the proximity of the Ambadongar Carbonatite Complex, Lower Narmada Valley, Gujarat, India. The dykes contain dense population of quartz xenocrysts within the basaltic matrix metasomatised by carbonate-rich fluids. Plagioclase feldspars, relict pyroxenes, chlorite, barite, rutile, magnetite, Fe-Ti oxides and glass were identified in the basaltic matrix. Quartz xenocrysts occur in various shapes and sizes and form an intricate growth pattern with carbonates. The xen...

  19. The sources and evolution of mineralising fluids in iron oxide-copper-gold systems, Norrbotten, Sweden: Constraints from Br/Cl ratios and stable Cl isotopes of fluid inclusion leachates

    Science.gov (United States)

    Gleeson, S. A.; Smith, M. P.

    2009-10-01

    We have analysed the halogen concentrations and chlorine stable isotope composition of fluid inclusion leachates from three spatially associated Fe-oxide ± Cu ± Au mineralising systems in Norrbotten, Sweden. Fluid inclusions in late-stage veins in Fe-oxide-apatite deposits contain saline brines and have a wide range of Br/Cl molar ratios, from 0.2 to 1.1 × 10 -3 and δ 37Cl values from -3.1‰ to -1.0‰. Leachates from saline fluid inclusions from the Greenstone and Porphyry hosted Cu-Au prospects have Br/Cl ratios that range from 0.2 to 0.5 × 10 -3 and δ 37Cl values from -5.6‰ to -1.3‰. Finally, the Cu-Au deposits hosted by the Nautanen Deformation Zone (NDZ) have Br/Cl molar ratios from 0.4 to 1.1 × 10 -3 and δ 37Cl values that range from -2.4‰ to +0.5‰, although the bulk of the data fall within 0‰ ± 0.5‰. The Br/Cl ratios of leachates are consistent with the derivation of salinity from magmatic sources or from the dissolution of halite. Most of the isotopic data from the Fe-oxide-apatite and Greenstone deposits are consistent with a mantle derived source of the chlorine, with the exception of the four samples with the most negative values. The origin of the low δ 37Cl values in these samples is unknown but we suggest that there may have been some modification of the Cl-isotope signature due to fractionation between the mineralising fluids and Cl-rich silicate assemblages found in the alteration haloes around the deposits. If such a process has occurred then a modified crustal source of the chlorine for all the samples cannot be ruled out although the amount of fractionation necessary to generate the low δ 37Cl values would be significantly larger. The source of Cl in the NDZ deposits has a crustal signature, which suggests the Cl in this system may be derived from (meta-) evaporites or from input from crustal melts such as granitic pegmatites of the Lina Suite.

  20. Study of REE behaviors, fluid inclusions, and O, S stable Isotopes in Zafar-abad iron skarn deposit, NW Divandarreh, Kordestan province

    Directory of Open Access Journals (Sweden)

    Mehrdad Barati

    2014-10-01

    Full Text Available Introduction The Zafar-abad iron ore deposit, situated in the NW part of Divandarreh (lat. 36°01'14" and long. 46°58'22". The ore body is located on the northern margin of the Sanandaj-Sirjan igneous metamorphic zone. The Zafar-abad Fe-skarn deposit is one of the important, medium- size mineral deposits in western Iran. REE patterns of skarn magnetite were among others studied in Skarn deposit by (Taylor, 1979 Hydrothermal alteration and fluid-rock interaction significantly affect total contents of REE and their patterns in fluids. Moreover, fractionation of REE by chemical complication, adsorption effects and redox reactions are characteristic processes determining REE behavior during crystallization. Stable isotope data for oxygen and sulfur have been widely used with great success to trace the origin and evolution history of paleo-hydrothermal fluids of meteoric, magmatic, and metamorphic. Materials and methods The present study investigates REE and stable Isotope geochemistry of magnetite and pyrite in Zafar-abad deposit and temperature of trapped fluid inclusions based on geothermometry analysis. In order to study the major, trace and REE compositions of Zafar-abad magnetite, twelve samples were collected from surface of ore exposures. The emphasis during sampling was on ores with primary textures. Discussion The Zafar-abad district is situated in Mesozoic and Cenozoic sedimentary, meta-sedimentary and meta-igneous rocks in Sanandaj-Sirjan igneous metamorphic zone. Sedimentary sequences dominantly composed of calcareous and conglomerate rocks. Various meta-sedimentary rocks are intercalated with the sedimentary rocks, and comprise biotite and muscovite-rich schist, calc-schist, calc-silicate rock. Several distinct ductile tectonic fabrics have been identified around the Zafar-abad deposit. The main ore body at Zafar-abad is in the form of a roughly horizontal, discordant, lens to tabular-shaped body plunging 10° NW, where it appears to

  1. Stratigraphy of the Harwell boreholes

    International Nuclear Information System (INIS)

    Gallois, R.W.; Worssam, B.C.

    1983-12-01

    Seven boreholes, five of them partially cored, were drilled at the Atomic Energy Research Establishment at Harwell as part of a general investigation to assess the feasibility of storing low- and intermediate-level radioactive waste in underground cavities. Two of the deeper boreholes were almost wholly cored to provide samples for hydrogeological, hydrochemical, mineralogical, geochemical, geotechnical, sedimentological and stratigraphical studies to enable variations in lithology and rock properties to be assessed, both vertically and laterally, and related to their regional geological setting. This report describes the lithologies, main faunal elements and stratigraphy of the Cretaceous, Jurassic, Triassic and Carboniferous sequences proved in the boreholes. More detailed stratigraphical accounts of the late Jurassic and Cretaceous sequences will be prepared when current studies of the faunal assemblages are complete. (author)

  2. Effect of explicit representation of detailed stratigraphy on brine and gas flow at the Waste Isolation Pilot Plant

    International Nuclear Information System (INIS)

    Christian-Frear, T.L.; Webb, S.W.

    1996-04-01

    Stratigraphic units of the Salado Formation at the Waste Isolation Pilot Plant (WIPP) disposal room horizon includes various layers of halite, polyhalitic halite, argillaceous halite, clay, and anhydrite. Current models, including those used in the WIPP Performance Assessment calculations, employ a ''composite stratigraphy'' approach in modeling. This study was initiated to evaluate the impact that an explicit representation of detailed stratigraphy around the repository may have on fluid flow compared to the simplified ''composite stratigraphy'' models currently employed. Sensitivity of model results to intrinsic permeability anisotropy, interbed fracturing, two-phase characteristic curves, and gas-generation rates were studied. The results of this study indicate that explicit representation of the stratigraphy maintains higher pressures and does not allow as much fluid to leave the disposal room as compared to the ''composite stratigraphy'' approach. However, the differences are relatively small. Gas migration distances are also different between the two approaches. However, for the two cases in which explicit layering results were considerably different than the composite model (anisotropic and vapor-limited), the gas-migration distances for both models were negligible. For the cases in which gas migration distances were considerable, van Genuchten/Parker and interbed fracture, the differences between the two models were fairly insignificant. Overall, this study suggests that explicit representation of the stratigraphy in the WIPP PA models is not required for the parameter variations modeled if ''global quantities'' (e.g., disposal room pressures, net brine and gas flux into and out of disposal rooms) are the only concern

  3. Origin and tectonic implications of the Zhaxikang Pb-Zn-Sb-Ag deposit in northern Himalaya: evidence from structures, Re-Os-Pb-S isotopes, and fluid inclusions

    Science.gov (United States)

    Zhou, Qing; Li, Wenchang; Qing, Chengshi; Lai, Yang; Li, Yingxu; Liao, Zhenwen; Wu, Jianyang; Wang, Shengwei; Dong, Lei; Tian, Enyuan

    2018-04-01

    The Zhaxikang Pb-Zn-Sb-Ag-(Au) deposits, located in the eastern part of northern Himalaya, totally contain more than 1.146 million tonnes (Mt) of Pb, 1.407 Mt of Zn, 0.345 Mt of Sb, and 3 kilotonnes (kt) of Ag. Our field observations suggest that these deposits are controlled by N-S trending and west- and steep-dipping normal faults, suggesting a hydrothermal rather than a syngenetic sedimentary origin. The Pb-Zn-Sb-Ag-(Cu-Au) mineralization formed in the Eocene as indicated by a Re-Os isochron age of 43.1 ± 2.5 Ma. Sulfide minerals have varying initial Pb isotopic compositions, with (206Pb/204Pb)i of 19.04-19.68, (207Pb/204Pb)i of 15.75-15.88, and (208Pb/204Pb)i of 39.66-40.31. Sulfur isotopic values display a narrow δ34S interval of +7.8-+12.2‰. These Pb-S isotopic data suggest that the Zhaxikang sources of Pb and S should be mainly from the coeval felsic magmas and partly from the surrounding Mesozoic strata including metasedimentary rocks and layered felsic volcanic rocks. Fluid inclusion studies indicate that the hydrothermal fluids have medium temperatures (200-336 °C) but varying salinities (1.40-18.25 wt.% NaCl equiv.) with densities of 0.75-0.95 g/cm3, possibly suggesting an evolution mixing between a high salinity fluid, perhaps of magmatic origin, with meteoric water.

  4. Hydrocarbon migration and accumulation in the Upper Cretaceous Qingshankou Formation, Changling Sag, southern Songliao Basin: Insights from integrated analyses of fluid inclusion, oil source correlation and basin modelling

    Science.gov (United States)

    Dong, Tian; He, Sheng; Wang, Dexi; Hou, Yuguang

    2014-08-01

    The Upper Cretaceous Qingshankou Formation acts as both the source and reservoir sequence in the Changling Sag, situated in the southern end of the Songliao Basin, northeast China. An integrated approach involving determination of hydrocarbon charging history, oil source correlation and hydrocarbon generation dynamic modeling was used to investigate hydrocarbon migration processes and further predict the favorable targets of hydrocarbon accumulations in the Qingshankou Formation. The hydrocarbon generation and charge history was investigated using fluid inclusion analysis, in combination with stratigraphic burial and thermal modeling. The source rocks began to generate hydrocarbons at around 82 Ma and the hydrocarbon charge event occurred from approximately 78 Ma to the end of Cretaceous (65.5 Ma) when a large tectonic uplift took place. Correlation of stable carbon isotopes of oils and extracts of source rocks indicates that oil was generated mainly from the first member of Qingshankou Formation (K2qn1), suggesting that hydrocarbon may have migrated vertically. Three dimensional (3D) petroleum system modeling was used to evaluate the processes of secondary hydrocarbon migration in the Qingshankou Formation since the latest Cretaceous. During the Late Cretaceous, hydrocarbon, mainly originated from the Qianan depression, migrated laterally to adjacent structural highs. Subsequent tectonic inversion, defined as the late Yanshan Orogeny, significantly changed hydrocarbon migration patterns, probably causing redistribution of primary hydrocarbon reservoirs. In the Tertiary, the Heidimiao depression was buried much deeper than the Qianan depression and became the main source kitchen. Hydrocarbon migration was primarily controlled by fluid potential and generally migrated from relatively high potential areas to low potential areas. Structural highs and lithologic transitions are potential traps for current oil and gas exploration. Finally, several preferred hydrocarbon

  5. Paleohydrogeological events recorded by stable isotopes, fluid inclusions and trace elements in fracture minerals in crystalline rock, Simpevarp area, SE Sweden

    International Nuclear Information System (INIS)

    Drake, Henrik; Tullborg, Eva-Lena

    2009-01-01

    Fracture minerals calcite, pyrite, gypsum, barite and quartz, formed during several events have been analysed for δ 13 C, δ 18 O, δ 34 S, 87 Sr/ 86 Sr, trace element chemistry and fluid inclusions in order to gain knowledge of the paleohydrogeological evolution of the Simpevarp area, south-eastern Sweden. This area is dominated by Proterozoic crystalline rocks and is currently being investigated by the Swedish Nuclear Fuel and Waste Management Co. (SKB) in order to find a suitable location for a deep-seated repository for spent nuclear fuel. Knowledge of the paleohydrogeological evolution is essential to understand the stability or evolution of the groundwater system over a time scale relevant to the performance assessment for a spent nuclear fuel repository. The ages of the minerals analysed range from the Proterozoic to possibly the Quaternary. The Proterozoic calcite and pyrite show inorganic and hydrothermal-magmatic stable isotope signatures and were probably formed during a long time period as indicated by the large span in temperatures (c. 200-360 deg. C) and salinities (0-24 wt.% eq. CaCl 2 ), obtained from fluid inclusion analyses. The Paleozoic minerals were formed from organically influenced brine-type fluids at temperatures of 80-145 deg. C. The isotopic results indicate that low temperature calcite and pyrite may have formed during different events ranging in time possibly from the end of the Paleozoic until the Quaternary. Formation conditions ranging from fresh to brackish and saline waters have been distinguished based on calcite crystal morphologies. The combination of δ 18 O and crystal morphologies show that the fresh-saline water interface has changed considerably over time, and water similar to the present meteoric water and brackish seawater at the site, have most probably earlier been residing in the bedrock. Organic influence and closed system in situ microbial activity causing disequilibrium are indicated by extremely low δ 13 C (down

  6. The orbital record in stratigraphy

    Science.gov (United States)

    Fischer, Alfred G.

    1992-01-01

    , and (2) presence of abundant microfossils yields close ties to geochronology. A tantalizing possibility that stratigraphy may yield a record of orbital signals unrelated to climate has turned up in magnetic studies of our Cretaceous core. Magnetic secular variations here carry a strong 39 ka periodicity, corresponding to the theoretical obliquity period of that time - Does the obliquity cycle perhaps have some direct influence on the magnetic field?

  7. Stratigraphy and dissolution of the Rustler Formation

    International Nuclear Information System (INIS)

    Bachman, G.O.

    1987-01-01

    This report describes the physical stratigraphy of the Rustler Formation, because the Waste Isolation Pilot Plant will be constructed in salt beds that underlie this formation. Described are subdivisions of the formations, the major karst features, and a proposed method for the formation of Nash Draw. 2 refs., 2 figs

  8. Revisiting the stratigraphy of the Mesoproterozoic Chhattisgarh ...

    Indian Academy of Sciences (India)

    The present work supports the existence of two sub-basins separated .... Updated geological map of the Chhattisgarh basin (this work). Cross sections along ..... Conclusion. This revisiting of the stratigraphy of Chhattisgarh. Supergroup requires three major corrections to the standard model (GSI 2005; Naqvi 2005). First, the.

  9. Investigation of oil-pool formation from the homogenization temperatures of fluid inclusions and biomarkers in reservoir rocks: a genetic model for the Deng-2 oil-pool in the Jiyuan Depression

    Energy Technology Data Exchange (ETDEWEB)

    Zhao Weiwei [Geochemical Institute of Chinese Academy, Guizhou (China); University of Petroleum, Shandong (China); Li Zhaoyang [University of Petroleum, Shandong (China); Jin Qiang; Wang Weifeng [Geochemical Institute of Chinese Academy, Guizhou (China)

    2002-11-01

    The Jiyuan Depression is a frontier area for oil and gas exploration in Henan Province, China. In recent years, oil was discovered in the Deng-2 well in the lower Tertiary, though the tectonics and petroleum geology of the Depression are very complex. A series of experiments on fluid inclusions in the oil-bearing sandstones from the Deng-2 well were made that included measurement of the homogenization temperatures of gas-liquid inclusions and GC-MS analysis of biomarkers either in the sandstone pores or in the fluid inclusions. The Deng-2 oil-reservoir was formed at about 78{sup o}C, corresponding to a burial depth of about 2200 m. The present burial depth is about 700 m because of erosion and fault-block uplift in Oligocene time. Although oil in the sandstone pores is now heavily biodegraded, the biomarkers in the inclusions show slight biodegradation representing a watering and biodegradation process that did not occur before formation of the Deng-2 oil- pool. Having investigated the structural evolution of the Deng-2 trap, it is concluded that the oil discovered in the Tertiary reservoir of Deng-2 well migrated from Mesozoic reservoirs through active faults around the Deng-2 trap. As the oil migrated from the Mesozoic to the Tertiary reservoir, the Deng-2 trap was uplifted close to the depth of active biodegradation (subsurface temperature lower than 80{sup o}C and to a burial depth shallower than 2250 m from the thermal gradient of 3.1{sup o}C/100 m) so that the oil in the inclusions shows a slight biodegradation. Because of the continuous uplift of the Deng-2 trap during the Tertiary and Quaternary, the reservoired oil has been more heavily biodegraded compared to that in the inclusions. (author)

  10. Modelling Forearc Basin Formation and Stratigraphy

    Science.gov (United States)

    Mannu, Utsav; Ueda, Kosuke; Willett, Sean; Gerya, Taras; Strasser, Michael

    2017-04-01

    Comparison of synthetic stratigraphy of forearc basins as generated in coupled plate subduction and accretionary wedge models to the stratal patterns observed for forearc basins in nature, could be used to ascertain the dynamic consistency of the interpreted deformational history of the wedge. Additionally, it could help us understand the emergence of stratigraphic patterns in forearc basins as an interplay between sedimentary flux and wedge dynamics. Here we present a simple methodology to generate synthetic stratigraphy by emplacing isochronal surfaces during the evolution of the wedge. We use a dynamic 2D, high-resolution, thermo-mechanical, subduction model coupled to an adaptive irregular surface grid to model the free surface. In this model, we track basin stratigraphy developing in the wedge top basins atop the accretionary prism by emplacing lines of Lagrangian markers at discrete times along the upper surface of the model, which subsequently are buried, transported, and deformed according to the velocity field generated in the model. We conduct numerical experiments to identify the stratigraphic signatures of different forearc basin formation mechanisms. We also study the impact of hinterland and trench sedimentation on the wedge evolution and its impact on forearc basin formation. Forearc basins that form on top of the overriding plate remain passive to the deformation history of the wedge. Forearc basins formed as negative alpha basins remain mostly undeformed. Forearc basins that form due to wedge stabilization exhibit landward tilting of strata with time. We also find that trench sedimentation enhances the landward tilting of the basin by shifting deformation landwards and potentially triggering out-of-sequence-thrust emergence/reactivation. Predicted stratigraphic features in our numerical models agree well with stratigraphic patterns observed in different types of forearc basins in the Nankai Trough, Sunda Strait and Lombok Basin offshore Japan, Java

  11. The global stratigraphy of the Cretaceous Tertiary boundary impact ejecta.

    NARCIS (Netherlands)

    Smit, J.

    1999-01-01

    The Chicxulub crater ejecta stratigraphy is reviewed, in the context of the stratigraphy of underlying and overlying rock sequences. The ejecta sequence is regionally grouped in (a) thick polymict and monomict breccia sequences inside the crater and within 300 km from the rim of the crater known

  12. The Krásná Hora, Milešov, and Příčovy Sb-Au ore deposits, Bohemian Massif: mineralogy, fluid inclusions, and stable isotope constraints on the deposit formation

    Science.gov (United States)

    Němec, Matěj; Zachariáš, Jiří

    2018-02-01

    The Krásná Hora-Milešov and Příčovy districts (Czech Republic) are the unique examples of Sb-Au subtype orogenic gold deposits in the Bohemian Massif. They are represented by quartz-stibnite veins and massive stibnite lenses grading into low-grade, disseminated ores in altered host rocks. Gold postdates the stibnite and is often replaced by aurostibite. The ore zones are hosted by hydrothermally altered dikes of lamprophyres (Krásná Hora-Milešov) or are associated with local strike-slip faults (Příčovy). Formation of Sb-Au deposits probably occurred shortly after the main gold-bearing event (348-338 Ma; Au-only deposits) in the central part of the Bohemian Massif. Fluid inclusion analyses suggest that stibnite precipitated at 250 to 130 °C and gold at 200 to 130 °C from low-salinity aqueous fluids. The main quartz gangue hosting the ore precipitated from the same type of fluid at about 300 °C. Early quartz-arsenopyrite veins are not associated with the Sb-Au deposition and formed from low-salinity, aqueous-carbonic fluid at higher pressure and temperature ( 250 MPa, 400 °C). The estimated oxygen isotope composition of the ore-bearing fluid (4 ± 1‰ SMOW; based on post-ore calcite) suggests its metamorphic or mixed magmatic-metamorphic origin and excludes the involvement of meteoric water. Rapid cooling of warm hydrothermal fluids reacting with "cold" host rock was probably the most important factor in the formation of both stibnite and gold.

  13. Inclusive pedagogy

    DEFF Research Database (Denmark)

    Korsgaard, Morten Timmermann; Mortensen, Stig Skov

    With a starting point in the tradition of geisteswissenschaftliche Pädagogik this article presents a challenge to inclusive education research to engage a continental perspective on educational research. The motivation is to entice inclusive education researchers to begin to ask educational...... questions of inclusion, as opposed to inclusive questions of education. Recent years has seen a call to re-think inclusive education research and this paper attempts to answer this call by turning to a Continental perspective and the emphasis on an at least relative autonomy for the theory and practice...... and the politicisation of inclusive education, and a positive aim in the form of an argument for a move towards constructing a pedagogical ideal of inclusion....

  14. Investigating the Controls on the Growth of Mississippi Valley-Type Zn-Pb Deposits in the U.S. Mid-Continent from Fluid Inclusion and Isotopic Analyses of Trace Occurrences of Mineralization

    Science.gov (United States)

    Field, J. D.; Appold, M. S.; Coveney, R. M., Jr.

    2016-12-01

    Mississippi Valley-type (MVT) Zn-Pb mineralization is common in the Paleozoic carbonate rocks of the U.S. mid-continent. Most occurrences consist of gram-scale quantities of sulfide minerals. However, in rare instances, millions of tons of Zn and Pb have been deposited at grades of several percent. These rare ore deposits have been well characterized. In contrast, little is known about the trace (gram-scale) MVT occurrences. The focus of the present study was to characterize some of these trace occurrences to compare to MVT ore deposits to look for controls on deposit growth. Results of the study show that compared to mid-continent MVT ore deposits, trace MVT occurrences have slightly lower fluid inclusion homogenization temperatures, K/Na and Ca/Mg ratios, similar Sr/Na ratios, a wider range of salinities, and lower methane concentrations. Fluid inclusion Pb concentrations could not be reliably quantified, but sphalerite matrix Pb concentrations in trace occurrences are within the range of MVT ore districts. The Pb isotope compositions of sulfide minerals in trace MVT occurrences in the western mid-continent are less radiogenic and in the northeastern mid-continent are more radiogenic than sulfide minerals from MVT ore districts. Sulfide minerals in trace MVT occurrence have much more variable and on the whole lighter sulfur isotope compositions than their MVT ore district counterparts. Collectively, the results of the present study indicate that the fluids that formed trace MVT occurrences in the U.S. mid-continent generally resemble the fluids that formed MVT ore deposits. Trace MVT occurrences considered in the present study may have formed at slightly shallower depths under more oxidizing conditions from fluids that were more frequently diluted by meteoric water than MVT ore deposits. Trace MVT occurrences in the western mid-continent appear to have incorporated less radiogenic basement Pb than MVT ore deposits or trace occurrences in the northeastern mid

  15. The Vein-type Zn-(Pb, Cu, As, Hg mineralization at Fedj Hassène orefield, North-Western Tunisia: Mineralogy, Trace Elements, Sulfur Isotopes and Fluid Inclusions

    Directory of Open Access Journals (Sweden)

    Bejaoui, J.

    2011-06-01

    Full Text Available The Fedj Hassène district is localized at the edge of the Tuniso-Algerian border 10 km of Ghardimaou area. It consists of a Zn-Pb vein type with minor amounts of Cu-As-Hg. The total Zn reserves are about 370.000t. The mineralization occurs within subparallel fractures to the Ain El Kohla ESE-WNW fault. Host rocks consist of limestones and marly limestones of the Middle Turonian. In the principal lode of Fedj Hassène, the mineralization occurs as vein filling of massive and brecciated brown sphalerite and minor galena ore with gangue. Other trace minerals are pyrite, chalcopyrite, orpiment, realgar, smithsonite and cerussite. LA-ICP-MS analyses in sphalerites show mean contents of 0,84 wt% Fe, 0,14 wt% Cd and 0,02 wt% Mn Ore. Fluid inclusions study in calcite and sphalerite reveals one mineralizing fluid characterized by an average salinity 23% wt NaCl with decreasing homogenisation temperature. In fact the temperature shows decrease from sphalerite to calcite. The fluid density that corresponds to trapping pressure ranges between 1.00 g/cm3 and 1.11 g/cm3 and pressure close to 200 bars. Microthermometric data in fluid inclusion hosted by gangue mineral presented by calcite show an average temperature of formation around 194°C. These inclusions homogenized to the liquid phase between 156°C and 210°C and salinities values ranging from 22 to 28 wt% NaCl and an average around 23% wt NaCl. The δ34S (VCDT values of sphalerite are in the range of + 4,6‰ to 6,4‰ (average=5,6‰. Thermochemical reduction of Triassic sulfate by reaction with hydro-carbons is the most probable source for the heavy and the narrow range of the ?34S values. Mineralogical, geochemical of trace elements, fluid inclusions and sulfur isotopes studies allow to include the vein-type ore field of Fedj Hassène in the polymetallic (Pb-Zn-As-Hg vein mineralization of the nappe zone in northern Tunisia and north eastern Algeria

  16. Shape factors inclusion in a one‐dimensional, transient two‐fluid model for stratified and slug flow simulations in pipes

    OpenAIRE

    Bonzanini, Arianna; Picchi, Davide; Ferrari, Marco; Poesio, Pietro

    2017-01-01

    In previous works, (Ferrari et al., 2017) have shown that a onedimensional, hyperbolic, transient five equations two-fluid model is able to numerically describe stratified, wavy, and slug flow in horizontal and near-horizontal pipes. Slug statistical characteristics, such as slug velocity, frequency, and length can be numerically predicted with results in good agreement with experimental data and well-known empirical relations. In this model some approximated and simplified assumptions are ad...

  17. Strontium isotope stratigraphy of the Pelotas Basin

    Energy Technology Data Exchange (ETDEWEB)

    Zerfass, Geise de Santana dos Anjos, E-mail: geise.zerfass@petrobras.com.br [Petroleo Brasileiro S.A. (PETROBRAS/CENPES/PDGEO/BPA), Rio de Janeiro, RJ (Brazil). Centro de Pesquisas e Desenvolvimento Leopoldo Americo Miguez de Mello; Chemale Junior, Farid, E-mail: fchemale@unb.br [Universidade de Brasilia (UnB), DF (Brazil). Instituto de Geociencias; Moura, Candido Augusto Veloso, E-mail: candido@ufpa.br [Universidade Federal do Para (UFPA), Belem, PA (Brazil). Centro de Geociencias. Dept. de Geoquimica e Petrologia; Costa, Karen Badaraco, E-mail: karen.costa@usp.br [Instituto Oceanografico, Sao Paulo, SP (Brazil); Kawashita, Koji, E-mail: koji@usp.br [Unversidade de Sao Paulo (USP), SP (Brazil). Centro de Pesquisas Geocronologicas

    2014-07-01

    Strontium isotope data were obtained from foraminifera shells of the Pelotas Basin Tertiary deposits to facilitate the refinement of the chronostratigraphic framework of this section. This represents the first approach to the acquisition of numerical ages for these strata. Strontium isotope stratigraphy allowed the identification of eight depositional hiatuses in the Eocene-Pliocene section, here classified as disconformities and a condensed section. The reconnaissance of depositional gaps based on confident age assignments represents an important advance considering the remarkably low chronostratigraphic resolution in the Cenozoic section of the Pelotas Basin. The recognition of hiatuses that match hiatuses is based on biostratigraphic data, as well as on global events. Furthermore, a substantial increase in the sedimentation rate of the upper Miocene section was identified. Paleotemperature and productivity trends were identified based on oxygen and carbon isotope data from the Oligocene-Miocene section, which are coherent with worldwide events, indicating the environmental conditions during sedimentation. (author)

  18. Inclusive pedagogy

    DEFF Research Database (Denmark)

    Korsgaard, Morten Timmermann; Skov Mortensen, Stig

    This article will present a case for a shift in perspective in inclusive education research towards a continentally inspired approach. Drawing on the age old distinction between continental and Anglo-American educational research the aim is to flesh out what a shift to a continental approach...... will entail, and why it might be beneficial to research in inclusive education...

  19. Social inclusion and inclusive education

    Directory of Open Access Journals (Sweden)

    Marsela Robo

    2014-07-01

    In line with global debate on social inclusion and exclusion, the author brings the way this debate has now pervaded both the official and development policy discourse in Albania.Social inclusion is considered as one of the priorities of the current government, with poverty reduction as its main focus, which will be ensured not only through economic development. In the end, the article focuses on the role of education as a very important and useful tool for ensuring social inclusion.Social inclusion through education, in particular through vocational education, considered by the author as the only way towards sustainable development of Albanian society.

  20. Geology, mineralization, and fluid inclusion characteristics of the Skrytoe reduced-type W skarn and stockwork deposit, Sikhote-Alin, Russia

    Science.gov (United States)

    Soloviev, Serguei G.; Kryazhev, Sergey G.

    2017-08-01

    The Skrytoe deposit (>145 Kt WO3, average grade 0.449% WO3) in the Sikhote-Alin orogenic system (Eastern Russia) is situated in a metallogenic belt of W, Sn-W, Au, and Au-W deposits formed in a late to post-collisional tectonic environment after cessation of active subduction. It is localized within a mineralized district of reduced-type skarn W and veined Au (±W) deposits and occurrences related to the Early Cretaceous ilmenite-series plutonic suite. The deposit incorporates large stockworks of scheelite-bearing veinlets related to propylitic (amphibole, chlorite, quartz) and phyllic (quartz, sericite, albite, apatite, and carbonate) hydrothermal alteration. The stockwork cuts flat-lying mafic volcanic rocks and limestone partially replaced by pyroxene skarn that host the major W orebodies. Scheelite is associated with pyrrhotite and/or arsenopyrite, with minor chalcopyrite and other sulfide minerals; the late phyllic stage assemblages hosts Bi and Au mineralization. The fluid evolution included low-salinity moderate-temperature, moderate-pressure (˜370-390 °C, ˜800 bars) methane-dominated carbonic-aqueous fluids that formed post-skarn propylitic alteration assemblages. Then, at the phyllic stage, there has been an evolution from methane-dominated, moderate-temperature (330-360 °C), low-salinity (deposition. The stable isotope data support a sedimentary source of carbon (δ13Cfluid = ˜-21 to -10 ‰), a magmatic source for water (δ18OH2O = +7.4 to +7.7 ‰), and dominantly crustal-derived source of sulfur (δ34S = -4.6 to -2.9 ‰) in the hydrothermal fluids. This is consistent with the development of larger, longer crystallizing crustal intermediate to felsic magma chambers in the late to post-collisional tectonic environment, with their protracted magmatic evolution advancing magmatic differentiation and partitioning of W into magmatic-hydrothermal fluid. The dominating role of the crustal-derived magmatic water, sulfur, and carbon appears to be an

  1. Sequence stratigraphy, seismic stratigraphy, and seismic structures of the lower intermediate confining unit and most of the Floridan aquifer system, Broward County, Florida

    Science.gov (United States)

    Cunningham, Kevin J.; Kluesner, Jared W.; Westcott, Richard L.; Robinson, Edward; Walker, Cameron; Khan, Shakira A.

    2017-12-08

    Deep well injection and disposal of treated wastewater into the highly transmissive saline Boulder Zone in the lower part of the Floridan aquifer system began in 1971. The zone of injection is a highly transmissive hydrogeologic unit, the Boulder Zone, in the lower part of the Floridan aquifer system. Since the 1990s, however, treated wastewater injection into the Boulder Zone in southeastern Florida has been detected at three treated wastewater injection utilities in the brackish upper part of the Floridan aquifer system designated for potential use as drinking water. At a time when usage of the Boulder Zone for treated wastewater disposal is increasing and the utilization of the upper part of the Floridan aquifer system for drinking water is intensifying, there is an urgency to understand the nature of cross-formational fluid flow and identify possible fluid pathways from the lower to upper zones of the Floridan aquifer system. To better understand the hydrogeologic controls on groundwater movement through the Floridan aquifer system in southeastern Florida, the U.S. Geological Survey and the Broward County Environmental Planning and Community Resilience Division conducted a 3.5-year cooperative study from July 2012 to December 2015. The study characterizes the sequence stratigraphy, seismic stratigraphy, and seismic structures of the lower part of the intermediate confining unit aquifer and most of the Floridan aquifer system.Data obtained to meet the study objective include 80 miles of high-resolution, two-dimensional (2D), seismic-reflection profiles acquired from canals in eastern Broward County. These profiles have been used to characterize the sequence stratigraphy, seismic stratigraphy, and seismic structures in a 425-square-mile study area. Horizon mapping of the seismic-reflection profiles and additional data collection from well logs and cores or cuttings from 44 wells were focused on construction of three-dimensional (3D) visualizations of eight

  2. Sequence stratigraphy on an early wet Mars

    Science.gov (United States)

    Barker, Donald C.; Bhattacharya, Janok P.

    2018-02-01

    The evolution of Mars as a water-bearing body is of considerable interest for the understanding of its early history and evolution. The principles of terrestrial sequence stratigraphy provide a useful conceptual framework to hypothesize about the stratigraphic history of the planets northern plains. We present a model based on the hypothesized presence of an early ocean and the accumulation of lowland sediments eroded from highland terrain during the time of the valley networks and later outflow channels. Ancient, global environmental changes, induced by a progressively cooling climate would have led to a protracted loss of surface and near surface water from low-latitudes and eventual cold-trapping at higher latitudes - resulting in a unique and prolonged, perpetual forced regression within basins and lowland depositional environments. The Messinian Salinity Crisis (MSC) serves as a potential terrestrial analogue of the depositional and environmental consequences relating to the progressive removal of large standing bodies of water. We suggest that the evolution of similar conditions on Mars would have led to the emplacement of diagnostic sequences of deposits and regional scale unconformities, consistent with intermittent resurfacing of the northern plains and the progressive loss of an early ocean by the end of the Hesperian era.

  3. Mineralization, geochemistry, fluid inclusion and sulfur stable isotope studies in the carbonate hosted Baqoroq Cu-Zn-As deposit (NE Anarak

    Directory of Open Access Journals (Sweden)

    Mohammad Ali Jazi

    2015-10-01

    , crustification banding,andbotryoidaltexture. The host rock has undergone dolomitization alteration Hypogene minerals include chalcopyrite, pyrite, sphalerite, galena, enargite, barite, and calcite. Supergene minerals include malachite, azurite, covellite, chrysocolla, chalcocite, cerussite, smithsonite, native copper and iron oxide minerals. Sulfantimonides and sulfardenides are abundant in low- and moderate temperature stages of the deposit, while bismuth sulfides generally occur in higher temperature ores, according to Malakhov, 1968. Analysis of rich ore samples indicates copper is the most abundant heavy metal in the ore (average 20.28 wt%, followed by zinc (average ~ 1 wt% and arsenic (average ~ 1 wt%, respectively. Thepresence of many trace elements in the ore, such as Sb, Pb, Ag and V, are very important. Element pairs such as Ag-Cu, Zn-Cd, Zn-Sb, Fe-V and Pb-Mo are correlated with each other. The Baqoroq ore minerals are rich in As, Sb and poor in Bi. Highamountsof antimony usually occur in a low temperature stage (Marshall and Joensuu, 1961. Malakhov (1968 suggested thata high Sb/Biratio in the ore indicates a low temperature of formation for the Baqoroq deposit. Sulfide mineralization fluids were found to have homogenization temperatures between 259 and 354°C and salinities between 8.37 and 13.18 wt% NaCl eq. Surface water apparently diluted theore-bearing fluids in the final stages and deposited sulfide-freecalcite veins at relatively low temperatures (78 to 112 °C and low salinities (3.59 to 6.07 wt% NaCl eq.. The δ34S values of barite of the Baqoroq deposit range from +13.1 to +14.37‰from whichδ34S values of ore fluids were calculated to vary between -8.57‰ and -7.23‰. Sulfur within natural environments is derived ultimately from either igneous or seawater sources (Ohmoto and Rye, 1979. Barite δ34S values of Baqoroq deposit lie within the range of Cretaceous-age oceanic sulfate values. The reduction of sulfate to sulfide couldhave been caused either by

  4. An evaporated seawater origin for the ore-forming brines in unconformity-related uranium deposits (Athabasca Basin, Canada): Cl/Br and δ 37Cl analysis of fluid inclusions

    Science.gov (United States)

    Richard, Antonin; Banks, David A.; Mercadier, Julien; Boiron, Marie-Christine; Cuney, Michel; Cathelineau, Michel

    2011-05-01

    Analyses of halogen concentration and stable chlorine isotope composition of fluid inclusions from hydrothermal quartz and carbonate veins spatially and temporally associated with giant unconformity-related uranium deposits from the Paleoproterozoic Athabasca Basin (Canada) were performed in order to determine the origin of chloride in the ore-forming brines. Microthermometric analyses show that samples contain variable amounts of a NaCl-rich brine (Cl concentration between 120,000 and 180,000 ppm) and a CaCl 2-rich brine (Cl concentration between 160,000 and 220,000 ppm). Molar Cl/Br ratios of fluid inclusion leachates range from ˜100 to ˜900, with most values between 150 and 350. Cl/Br ratios below 650 (seawater value) indicate that the high salinities were acquired by evaporation of seawater. Most δ 37Cl values are between -0.6‰ and 0‰ (seawater value) which is also compatible with a common evaporated seawater origin for both NaCl- and CaCl 2-rich brines. Slight discrepancies between the Cl concentration, Cl/Br, δ 37Cl data and seawater evaporation trends, indicate that the evaporated seawater underwent secondary minor modification of its composition by: (i) mixing with a minor amount of halite-dissolution brine or re-equilibration with halite during burial; (ii) dilution in a maximum of 30% of connate and/or formation waters during its migration towards the base of the Athabasca sandstones; (iii) leaching of chloride from biotites within basement rocks and (iv) water loss by hydration reactions in alteration haloes linked to uranium deposition. The chloride in uranium ore-forming brines of the Athabasca Basin has an unambiguous dominantly marine origin and has required large-scale seawater evaporation and evaporite deposition. Although the direct evidence for evaporative environments in the Athabasca Basin are lacking due to the erosion of ˜80% of the sedimentary pile, Cl/Br ratios and δ 37Cl values of brines have behaved conservatively at the basin

  5. Fluids in metamorphic rocks

    NARCIS (Netherlands)

    Touret, J.L.R.

    2001-01-01

    Basic principles for the study of fluid inclusions in metamorphic rocks are reviewed and illustrated. A major problem relates to the number of inclusions, possibly formed on a wide range of P-T conditions, having also suffered, in most cases, extensive changes after initial trapping. The

  6. Lithology, microstructures, fluid inclusions, and geochemistry of rock salt and of the cap-rock contact in Oakwood Dome, East Texas: significance for nuclear waste storage. Report of investigations No. 120

    International Nuclear Information System (INIS)

    Dix, O.R.; Jackson, M.P.A.

    1982-01-01

    Oakwood salt dome in Leon and Freestone Counties, Texas, has a core composed of a diapiric salt stock at a depth of 355 m. A vertical borehole in the center of the salt stock yielded 57.3 m of continuous rock-salt core overlain by 137 m of anhydrite-calcite cap rock. The lower 55.3 m of rock salt exhibits a strong, penetrative schistosity and parallel cleavage dipping at 30 to 40 0 and more than 60 variably dipping layers of disseminated anhydrite. Anhydrite constitutes 1.3 +- 0.7 percent of the rock-salt core. The upper 2 m of rock salt is unfoliated, comprising a lower 1.4-m interval of medium-grained granoblastic rock salt and an upper 0.6-m interval of coarse-grained granoblastic rock salt. An abrupt, cavity-free contact separates rock salt from laminated cap rock consisting of granoblastic-polygonal anhydrite virtually devoid of halite or pore space. Microstructures and concentration gradients of fluid inclusions suggest that the unfoliated rock salt at the crest of the salt stock was once strongly foliated, but that this fabric was destroyed by solid-state recrystallization. Downward movement of brine from the rock-salt - cap-rock contact was apparently accompanied by two recrystallization fronts. Dissolution of halite at the contact released disseminated anhydrite that presumably accumulated as sand on the floor of the dissolution cavity. Renewed rise of the salt stock closed the cavity, and the anhydrite sand was accreted against the base of the cap rock. Much, if not all, of the lamination in the 80 m of anhydrite cap rock may result from cycles of dissolution, recrystallization, and upward movement in the salt stock, followed by accretion of anhydrite residuum as laminae against the base of the cap rock. These processes, which are strongly influenced by fluids, act both to breach waste repositories and to geologically isolate them

  7. Translating Inclusion

    DEFF Research Database (Denmark)

    Fallov, Mia Arp; Birk, Rasmus

    2018-01-01

    The purpose of this paper is to explore how practices of translation shape particular paths of inclusion for people living in marginalized residential areas in Denmark. Inclusion, we argue, is not an end-state, but rather something which must be constantly performed. Active citizenship, today......, is not merely a question of participation, but of learning to become active in all spheres of life. The paper draws on empirical examples from a multi-sited field work in 6 different sites of local community work in Denmark, to demonstrate how different dimensions of translation are involved in shaping active...... citizenship. We propose the following different dimensions of translation: translating authority, translating language, translating social problems. The paper takes its theoretical point of departure from assemblage urbanism, arguing that cities are heterogeneous assemblages of socio-material interactions...

  8. Social imaginaries and inclusion

    DEFF Research Database (Denmark)

    Hansen, Janne Hedegaard

    2016-01-01

    , the development of inclusive schools and inclusive learning environments will involve both inclusion and exclusion processes. With this starting point, international educational research knowledge about inclusive schools and inclusive learning environments in general will be related to the fundamental dilemma...

  9. Genetics Home Reference: microvillus inclusion disease

    Science.gov (United States)

    ... At least 200 cases have been reported in Europe, although this condition occurs worldwide. Related Information What ... and fluids during digestion leads to recurrent diarrhea, malnutrition, and dehydration in individuals with microvillus inclusion disease . ...

  10. Stiffening solids with liquid inclusions

    Science.gov (United States)

    Style, Robert W.; Boltyanskiy, Rostislav; Allen, Benjamin; Jensen, Katharine E.; Foote, Henry P.; Wettlaufer, John S.; Dufresne, Eric R.

    2015-01-01

    From bone and wood to concrete and carbon fibre, composites are ubiquitous natural and synthetic materials. Eshelby’s inclusion theory describes how macroscopic stress fields couple to isolated microscopic inclusions, allowing prediction of a composite’s bulk mechanical properties from a knowledge of its microstructure. It has been extended to describe a wide variety of phenomena from solid fracture to cell adhesion. Here, we show experimentally and theoretically that Eshelby’s theory breaks down for small liquid inclusions in a soft solid. In this limit, an isolated droplet’s deformation is strongly size-dependent, with the smallest droplets mimicking the behaviour of solid inclusions. Furthermore, in opposition to the predictions of conventional composite theory, we find that finite concentrations of small liquid inclusions enhance the stiffness of soft solids. A straightforward extension of Eshelby’s theory, accounting for the surface tension of the solid-liquid interface, explains our experimental observations. The counterintuitive stiffening of solids by fluid inclusions is expected whenever inclusion radii are smaller than an elastocapillary length, given by the ratio of the surface tension to Young’s modulus of the solid matrix. These results suggest that surface tension can be a simple and effective mechanism to cloak the far-field elastic signature of inclusions.

  11. Sedimentary facies control on mechanical and fracture stratigraphy in turbidites

    NARCIS (Netherlands)

    Ogata, Kei; Storti, Fabrizio; Balsamo, Fabrizio; Tinterri, Roberto; Bedogni, Enrico; Fetter, Marcos; Gomes, Leonardo; Hatushika, Raphael

    2017-01-01

    Natural fracture networks exert a first-order control on the exploitation of resources such as aquifers, hydrocarbons, and geothermal reservoirs, and on environmental issues like underground gas storage and waste disposal. Fractures and the mechanical stratigraphy of layered sequences have been

  12. The application of seismic-log sequence stratigraphy in mapping ...

    African Journals Online (AJOL)

    The concept of seismic-log sequence stratigraphy was used in mapping stratigraphic traps and reservoirs' facies in Afam Channel area, Niger Delta, for the purpose of prospect re-evaluation and improving production. The data set consists of 3-D seismic data and conventional well logs, which were interpreted iteratively ...

  13. Some Modifications in the Stratigraphy of Manganese Bearing ...

    African Journals Online (AJOL)

    Some Modifications in the Stratigraphy of Manganese Bearing Formations, Srikakulam District (A.P.) India. ... Hitherto unknown, these shales and algal bodies are of sedimentary origin. Their occurrence ... Keywords: crystalline algal limestone, red and green shale, Khondalite group, manganese quarries, Andhra Pradesh.

  14. Workshop on quantitative dynamic stratigraphy. Final conference report

    Energy Technology Data Exchange (ETDEWEB)

    Cross, T.A.

    1988-04-01

    This document discusses the development of quantitative simulation models for the investigation of geologic systems. The selection of variables, model verification, evaluation, and future directions in quantitative dynamic stratigraphy (QDS) models are detailed. Interdisciplinary applications, integration, implementation, and transfer of QDS are also discussed. (FI)

  15. Genesis of amethyst geodes in basaltic rocks of the Serra Geral Formation (Ametista do Sul, Rio Grande do Sul, Brazil): a fluid inclusion, REE, oxygen, carbon, and Sr isotope study on basalt, quartz, and calcite

    Science.gov (United States)

    Gilg, H. Albert; Morteani, Giulio; Kostitsyn, Yuri; Preinfalk, Christine; Gatter, Istvan; Strieder, Adelir J.

    2003-12-01

    In the Ametista do Sul area, Rio Grande do Sul, Brazil, amethyst-bearing geodes are hosted by a ~40- to 50-m-thick subhorizontal high-Ti basaltic lava flow of the Lower Cretaceous Paraná Continental Flood Basalt Province. The typically spherical cap-shaped, sometimes vertically elongated geodes display an outer rim of celadonite followed inwards by agate and colorless and finally amethystine quartz. Calcite formed throughout the whole crystallization sequence, but most commonly as very late euhedral crystals, sometimes with gypsum, in the central cavity. Fluid inclusions in colorless quartz and amethyst are predominantly monophase and contain an aqueous liquid. Two-phase liquid-vapor inclusions are rare. Some with a consistent degree of fill homogenize into the liquid between 95 and 98 °C. Ice-melting temperatures in the absence of a vapor phase between -4 and +4 °C indicate low salinities. Chondrite-normalized REE patterns of calcites are highly variable and show generally no systematic correlation with the paragenetic sequence. The oxygen isotope composition of calcites is very homogeneous (δ18OVSMOW=24.9±1.1‰, n=34) indicating crystallization temperatures of less than 100 °C. Carbon isotope values of calcites show a considerable variation ranging from -18.7 to -2.9‰ (VPDB). The 87Sr/86Sr ratio of calcites varies between 0.706 and 0.708 and is more radiogenic than that of the host basalt (~0.705). The most likely source of silica, calcium, carbon, and minor elements in the infill of the geodes is the highly reactive interstitial glass of the host basalts leached by gas-poor aqueous solutions of meteoric origin ascending from the locally artesian Botucatú aquifer system in the footwall of the volcanic sequence. The genesis of amethyst geodes in basalts at Ametista do Sul, Brazil, is thus considered as a two-stage process with an early magmatic protogeode formation and a late, low temperature infill of the cavity.

  16. East Greenland Caledonides: stratigraphy, structure and geochronology: Lower Palaeozoic stratigraphy of the East Greenland Caledonides

    Directory of Open Access Journals (Sweden)

    Smith, M. Paul

    2004-12-01

    Full Text Available The Lower Palaeozoic stratigraphy of the East Greenland Caledonides, from the fjord region of North-East Greenland northwards to Kronprins Christian Land, is reviewed and a number of new lithostratigraphical units are proposed. The Slottet Formation (new is a Lower Cambrian quartzite unit, containing Skolithos burrows, that is present in the Målebjerg and Eleonore Sø tectonic windows, in the nunatak region of North-East Greenland. The unit is the source of common and often-reported glacial erratic boulders containing Skolithos that are distributed throughout the fjord region. The Målebjerg Formation (new overlies the Slottet Formation in the tectonic windows, and comprises limestones and dolostones of assumed Cambrian–Ordovician age. The Lower Palaeozoic succession of the fjord region of East Greenland (dominantly limestones and dolostones is formally placed in the Kong Oscar Fjord Group (new. Amendments are proposed for several existing units in the Kronprins Christian Land and Lambert Land areas, where they occur in autochthonous, parautochthonous and allochthonous settings.

  17. Absolute chronology and stratigraphy of Lepenski Vir

    Directory of Open Access Journals (Sweden)

    Borić Dušan

    2007-01-01

    radiometric dates from Lepenski Vir 21 made by the conventional 14C dating of charcoal and 8 AMS dates made on animal (3 dates and human bones (5 dates. There is also a series of 20 new AMS dates made on human bones from Lepenski Vir. The last group of dates has not been published with all the contextual details and are of limited use in our analyses of absolute chronology and stratigraphy of Lepenski Vir. New dates are listed in Table 1. From 32 dated contexts from Lepenski Vir, 27 contexts are stratigraphically related to trapezoidal buildings while 5 dates are connected with the area outside of buildings. From those contexts related to trapezoidal structures, 24 contexts are dated with animal and 3 with human bones. The emphasis on the dating of animal bones is connected with problems of precision when dating samples made on human and dog bones due to the reservoir effect and the deposition of 'old' carbon. Dated remains of animal and human bones originate from the following types of stratigraphic contexts a beneath building floors, i.e. stratigraphically the oldest contexts in the settlement (2 dates (Fig. 2; b between two superposed floors of trapezoidal buildings as 'sealed' contexts (8 dates (Fig. 3; c lying directly on top of the floors of trapezoidal buildings but not overlapped by a later floor (17 dates (Fig. 3; d outside of trapezoidal buildings, found in contexts such as pits, domed ovens, and burials, or in contexts that can be attributed to the occupation layer only (6 dates (Fig. 4. The new dates indicate a very long duration of the Mesolithic period, from around 9400 to around 7500 cal BC (Fig. 2, 23. These early dates are concentrated in two particular periods that may point to two separate phases within these two millennia, with settlement discontinuities. It remains possible that there were many more occupation episodes that these dates do not encompass, and more AMS dates may indicate whether these two groupings with three dates per grouping are

  18. Stratigraphy and paleohydrology of delta channel deposits, Jezero crater, Mars

    Science.gov (United States)

    Goudge, Timothy A.; Mohrig, David; Cardenas, Benjamin T.; Hughes, Cory M.; Fassett, Caleb I.

    2018-02-01

    The Jezero crater open-basin lake contains two well-exposed fluvial sedimentary deposits formed early in martian history. Here, we examine the geometry and architecture of the Jezero western delta fluvial stratigraphy using high-resolution orbital images and digital elevation models (DEMs). The goal of this analysis is to reconstruct the evolution of the delta and associated shoreline position. The delta outcrop contains three distinct classes of fluvial stratigraphy that we interpret, from oldest to youngest, as: (1) point bar strata deposited by repeated flood events in meandering channels; (2) inverted channel-filling deposits formed by avulsive distributary channels; and (3) a valley that incises the deposit. We use DEMs to quantify the geometry of the channel deposits and estimate flow depths of ∼7 m for the meandering channels and ∼2 m for the avulsive distributary channels. Using these estimates, we employ a novel approach for assessing paleohydrology of the formative channels in relative terms. This analysis indicates that the shift from meandering to avulsive distributary channels was associated with an approximately four-fold decrease in the water to sediment discharge ratio. We use observations of the fluvial stratigraphy and channel paleohydrology to propose a model for the evolution of the Jezero western delta. The delta stratigraphy records lake level rise and shoreline transgression associated with approximately continuous filling of the basin, followed by outlet breaching, and eventual erosion of the delta. Our results imply a martian surface environment during the period of delta formation that supplied sufficient surface runoff to fill the Jezero basin without major drops in lake level, but also with discrete flooding events at non-orbital (e.g., annual to decadal) timescales.

  19. Diamond growth in mantle fluids

    OpenAIRE

    Bureau, Hélène; Frost, Daniel J.; Bolfan-casanova, Nathalie; Leroy, Clémence; Esteve, Imène; Cordier, Patrick

    2016-01-01

    International audience; In the upper mantle, diamonds can potentially grow from various forms of media (solid, gas, fluid) with a range of compositions (e.g. graphite, C–O–H fluids, silicate or carbonate melts). Inclusions trapped in diamonds are one of the few diagnostic tools that can constrain diamond growth conditions in the Earth's mantle. In this study, inclusion-bearing diamonds have been synthesized to understand the growth conditions of natural diamonds in the upper mantle. Diamonds ...

  20. Elastic-Wavefield Seismic Stratigraphy: A New Seismic Imaging Technology

    Energy Technology Data Exchange (ETDEWEB)

    Bob A. Hardage; Milo M. Backus; Michael V. DeAngelo; Sergey Fomel; Khaled Fouad; Robert J. Graebner; Paul E. Murray; Randy Remington; Diana Sava

    2006-07-31

    The purpose of our research has been to develop and demonstrate a seismic technology that will provide the oil and gas industry a better methodology for understanding reservoir and seal architectures and for improving interpretations of hydrocarbon systems. Our research goal was to expand the valuable science of seismic stratigraphy beyond the constraints of compressional (P-P) seismic data by using all modes (P-P, P-SV, SH-SH, SV-SV, SV-P) of a seismic elastic wavefield to define depositional sequences and facies. Our objective was to demonstrate that one or more modes of an elastic wavefield may image stratal surfaces across some stratigraphic intervals that are not seen by companion wave modes and thus provide different, but equally valid, information regarding depositional sequences and sedimentary facies within that interval. We use the term elastic wavefield stratigraphy to describe the methodology we use to integrate seismic sequences and seismic facies from all modes of an elastic wavefield into a seismic interpretation. We interpreted both onshore and marine multicomponent seismic surveys to select the data examples that we use to document the principles of elastic wavefield stratigraphy. We have also used examples from published papers that illustrate some concepts better than did the multicomponent seismic data that were available for our analysis. In each interpretation study, we used rock physics modeling to explain how and why certain geological conditions caused differences in P and S reflectivities that resulted in P-wave seismic sequences and facies being different from depth-equivalent S-wave sequences and facies across the targets we studied.

  1. Lappajarvi Meteorite Crater, Western Finland: Structure, Stratigraphy and Geochemistry

    Science.gov (United States)

    Pipping, F.

    1992-07-01

    Research drill holes drilled in the 23 km diameter Lappajarvi Late Cretaceous meteorite impact crater give new information as to the structure, stratigraphy, and geochemistry of the impact formation in the crater (Pipping & Lehtinen, 1992). In one drill hole the sheet of glassy melt rock is 145 m thick and is underlain by 30 m of suevitic rock, followed by loose breccias down to 209 m where the hole ends. In a nearby hole 65 m of suevitic breccia was penetrated, underlain by a fine-grained allochthonous breccia to 160 m, followed by an autochthonous coarse breccia cut by suevitic dikes down to 275 m where the hole ends. A third hole was bored close to the crater rim. Topmost is 75 m of Quaternary glacial tills. After an erosional boundary follows 20 m of Mesoproterozoic (ca. 1200 Ma) sandy-silty sediments. These are underlain--with a tectonic boundary--by an autochthonous saprolite crust of about 40 m thickness. The hole ended in fresh mica schist--no signs of shock metamorphism--at 165 m. The structure typical for large impact craters was thus confirmed, i.e. an annular trough inside the rim of the crater, filled with rocks older than the impact. The stratigraphy of the crater fill is: lowermost autochthonous breccias followed by allochthonous breccias and suevitic breccias, with a melt rock cap covering a part of the crater fill. The general stratigraphy is: Palaeoproterozoic mica schists (1900 Ma), Mesoproterozoic saprolite (1400 Ma) in peneplanated schists, Neoproterozoic sediments (1200 Ma), Late Cretaceous crater (77 Ma, Jessberger & Reimold,1980) with a fill of impact rocks, Quaternary glaciation and sedimentation, and last, recent lake sedimentation. Impact rock geochemistry gives conclusive proof of an origin by meteorite impact. Conspicuous is the threefold Ni-content of the melt rock compared with the target rock, and the two-to-tenfold content of the Pt-metals in the melt rocks and suevites, compared with the target schists. Increased levels of K and Se

  2. Evaluation of the structure and stratigraphy over Richton Dome, Mississippi

    International Nuclear Information System (INIS)

    Werner, M.L.

    1986-05-01

    The structure and stratigraphy over Richton Salt Dome, Mississippi, have been evaluated from 70 borings that were completed to various depths above the dome. Seven lithologic units have been identified and tentatively correlated with the regional Tertiary stratigraphy. Structure-contour and thickness maps of the units show the effects of dome growth from Eocene through early Pliocene time. Growth of the salt stock from late Oligocene through early Pliocene is estimated to have averaged 0.6 to 2.6 centimeters (0.2 to 1.1 inches) per 1000 years. No dome growth has occurred since the early Pliocene. The late Oligocene to early Pliocene strata over and adjacent to the dome reflect arching over the entire salt stock; some additional arching over individual centers may represent pre-Quaternary differential movement in the salt stock. The lithology and structure of the caprock at the Richton Salt Dome indicate that the caprock probably was completely formed by late Oligocene. In late Oligocene, the caprock was fractured by arching and altered by gypsum veining. Since late Oligocene, there are no indications of significant hydrologic connections through the caprock - that is, there are no indications of dissolution collapse or further anhydrite caprock accumulation. This structural and stratigraphic analysis provides insights on dome growth history, dome geometry, and neardome hydrostratigraphy that will aid in planning site characterization field activities, including an exploratory shaft, and in the conceptual design of a high-level waste (HLW) repository

  3. Limits to Inclusion

    Science.gov (United States)

    Hansen, Janne Hedegaard

    2012-01-01

    In this article, I will argue that a theoretical identification of the limit to inclusion is needed in the conceptual identification of inclusion. On the one hand, inclusion is formulated as a vision that is, in principle, limitless. On the other hand, there seems to be an agreement that inclusion has a limit in the pedagogical practice. However,…

  4. Fluid inclusions in minerals associated to uranium mineralization in Jazida do Engenho (anomaly 09), Lagoa Real uranium province - Bahia, Brazil; Inclusoes fluidas nos minerais associados a mineralizacao uranifera da Jazida do Engenho (Anomalia 09), provincia uranifera de Lagoa Real, BA

    Energy Technology Data Exchange (ETDEWEB)

    Souza, Aurelio da Silva de

    2009-07-01

    The Engenho deposit (anomaly 09) is south-eastern from Cachoeira Mine (anomaly 13), in the northern part of the Province. The uranium mineralization is associated to 'albitites' (over 70% of albite/oligoclase). Epidosites with uranium may also occur. The 'albitite' main minerals are pyroxene, gamet, albite/oligoclase feldspar, amphibole and biotite. Pyroxene, gamet, plagioclase, titanite and epidote are the minerals associated to the uranium mineralization. The fluids related to pyroxene, gamet and epidote are aqueous-saline, primary and with no carbonic phases and are constant, with small variations. They all present medium to high salinity (14 to 18wt% NaCl eq.), the higher values being related to pyroxene and the lower ones related to gamet and epidote. The fluids associated to albite/oligoclase, although aqua-saline and with no carbonic phases, show salinities much lower than in pyroxene, gamet and epidote, suggesting a intense dilution process indicating dilution toward the later minerals phases. The data suggest the pyroxene formation process occurring under a 3,5 kbar pressure condition which corresponds to approximately 10km depth. The dispersion on Th in albites, due probably to the overheating and non elastic increase in volume, precluded a reliable pressure calculation. The IF's microscopy m plagioclase gneiss (albitites host-rocks) suggests the probability of primary carbonic fluids associated to these minerals. The fluids with CO{sub 2} showed in the gneiss maybe also be present in the albitites, probably as late or intergranular fluids. This assumption is based on the fact that signs of carbonic gases were shown during crushing tests. These tendencies suggest the occurrence of two albitization phases in this Lagoa Real area: one associated to a fluid composed by H{sub 2}O + CO{sub 2} + salts (in the gneiss host) and another (in the albitite) formed by an aqueous-saline phase. The data indicate the Brasiliano event as a thermal

  5. Removal of Inclusions from Aluminum Through Filtration

    Science.gov (United States)

    Damoah, Lucas Nana Wiredu; Zhang, Lifeng

    2010-08-01

    Filtration experiments were carried out using both an AlF3 slurry-coated and an uncoated Al2O3 ceramic foam filter to study the removal of nonmetallic inclusions and impurity elements. The results showed that the 30-ppi ceramic foam filter removed up to 85 pct inclusions from aluminum. Several pictures of two- and three-dimensional morphologies of both nonmetallic and intermetallics inclusions also have been presented. The following contributing mechanisms for the removal of nonmetallic inclusions in the deep-bed filtration mode are proposed: (1) collision with walls and interception effect and (2) the formation of both intermetallic and nonmetallic inclusion bridges during filtration. Fluid dynamics modeling of inclusion attachment to the filter walls showed that most inclusions, especially those with larger sizes, are entrapped at the upper part of the filter, whereas smaller inclusions are dispersed well throughout the filter. The calculated inclusions removal fractions for the 30-ppi filter showed that almost all inclusions >125 μm are removed, and inclusions ~5 μm in size are removed up to 85 pct. The interfacial energy between two collided same-size inclusions was calculated, indicating that a strong clustering of inclusions may result within the filter window. Magnesium impurities were removed up to 86 pct by the AlF3 slurry-coated filter. The filter acted in active filtration mode in addition to the contribution of the air oxidation of dissolved [Mg], which was calculated to be 13 pct. The total mass transfer coefficient of dissolved [Mg] to the reaction interface was calculated to be 1.15 × 10-6 m/s.

  6. Geology, mineralization, and fluid inclusion characteristics of the Kashkasu W-Mo-Cu skarn deposit associated with a high-potassic to shoshonitic igneous suite in Kyrgyzstan, Tien Shan: Toward a diversity of W mineralization in Central Asia

    Science.gov (United States)

    Soloviev, Serguei G.; Kryazhev, Sergey G.

    2018-03-01

    The Kashkasu deposit is part of the subduction-related Late Paleozoic (Late Carboniferous) metallogenic belt of Tien Shan. It is associated with a multiphase monzodiorite-monzonite-granodiorite-granite pluton of the magnetite-series high-K calc-alkaline to shoshonitic igneous suite. The deposit contains zones of W-Mo-Cu oxidized prograde and retrograde skarns, with abundant andraditic garnet, magnetite, locally scapolite and K-feldspar, as well as scheelite, chalcopyrite, and molybdenite. Skarns are overprinted by quartz-carbonate-sericite (phyllic alteration) zones with scheelite and sulfides. Prograde calcic skarn and initial retrograde skarns were formed from a high temperature (650 °C to 450-550 °C), high pressure (2000 bars to 600-900 bars) magmatic-hydrothermal low- to high-salinity aqueous chloride fluid. The gradual fluid evolution was interrupted by the intrusion of granodiorite and likely associated release of low-salinity (∼7-8 wt% NaCl equiv.) fluid. Ascent of this fluid to shallower levels and/or its cooling to 400-500 °C has resulted in phase separation into low-salinity (2.1-3.1 wt% NaCl equiv.) vapor and coexisting brine (35-40 wt% NaCl equiv.). The boiling was coincident with most intense scheelite deposition in retrograde skarn. Later retrograde skarn assemblages were formed from a gaseous, low- to moderate-salinity (3.4-8.1 wt% NaCl equiv.) fluid and then from high salinity (37-42 wt% NaCl equiv.) aqueous chloride fluids, the latter being enriched in Ca (17-20 wt% CaCl2) that could also affect scheelite deposition. Another cycle of fluid exsolution from crystallizing magma corresponded to quartz-carbonate-sericite-scheelite-sulfide (phyllic) alteration stage, with the early low-salinity (5.3-8.4 wt% NaCl-equiv.) fluid followed by later high-salinity (33.5-38.2 wt% NaCl-equiv.) fluid. The sulfur isotope data (δ34S = +5.1 to +9.0) suggest significant sulfur sourcing from sedimentary rocks enriched in seawater sulfate, possibly evaporites.

  7. Sediment transport processes and their resulting stratigraphy: informing science and society

    Science.gov (United States)

    Nittrouer, J. A.

    2013-12-01

    Sediment transport physically shapes planetary surfaces by producing patterns of erosion and deposition, with the relative magnitudes of geomorphic actions varying according to environmental conditions. Where sediment fills accommodation space and generates accumulation, a stratigraphic archive develops that potentially harbors a trove of information documenting dynamic conditions during the periods of sediment production, transport and deposition. By investigating the stratigraphic record, it is possible to describe changes in surface environments, as well as hypothesize about the development of regional tectonic and climate regimes. Ultimately, information contained within the stratigraphic record is critical for evaluating the geological history of terrestrial planets. The enigma of stratigraphy, however, is that sediment deposition is finicky, there is no uninterrupted record, and while deposits may reflect only a brief temporal window, they may still be used to infer about conditions that encompass much longer periods of time. Consider a case where meter-scale dune foresets, deposited in a matter of minutes to hours, are in contact with sediments above and below that reflect entirely different depositional circumstances and are separated in time by a hiatus of thousands or perhaps millions of years. To effectively unlock the scientific trove bound in stratigraphy, it is first necessary to identify where such unconformities exist and the conditions that lead to their development. This challenge is made much simpler through scientific advances in understanding sediment transport processes -- the examination of how fluid and solids interact under modern conditions -- because this is precisely where sediment patterns first emerge to produce accumulation that builds a stratigraphic record. By advancing an understanding of process-based sedimentology, it is possible to enhance diagnostic evaluations of the stratigraphic record. Fortunately, over the past several

  8. Magnetic stratigraphy of Peralkaline Volcanism in Sierra Libre, Sonora, Mexico

    Science.gov (United States)

    Olguin-Villa, A. E.; Stock, J. M.; Vidal-Solano, J. R.

    2011-12-01

    Middle Miocene (~12 Ma) magmatism in NW Mexico was dominated by the appearance of anorogenic liquids associated with the Proto-Gulf of California. These correspond to a few occurrences of mafic volcanic rocks with transitional signatures (geochemically) and to a larger silicic volcanic event of peralkaline affinity. The silicic event is primarily composed of a large ignimbritic deposit widely recognized in Baja California as the Tuff of San Felipe (TSF), and in Sonora as the Hermosillo Ignimbrite. These are correlated by a number of characteristics including a unique low-inclination, reversed magnetization, probably associated with a field transition or a geomagnetic excursion within a reversed polarity subchron at 11.531-11.935 Ma (base of C5r.3r; Cande and Kent, 1995). Thick sections of deposits of this peralkaline volcanism crop out at Sierra Libre, geographically located ~45 km south of Hermosillo, Sonora. In this locality, a ~180m thick stack of middle Miocene volcanic units (both pyroclastic and lavas) were sampled for paleomagnetic studies focusing on the magnetic stratigraphy of a set of 9 units (7 to 12 cores per unit) from El Galindro Canyon, which represents the thickest volcanic pile genetically related to Tuff of San Felipe and Hermosillo ignimbrite. Previous studies indicated that the anomalous magnetization from TSF could be either an excursion or a reversal transition - its age is unconstrained except by direct radiological isotopes and relative stratigraphy. But most excursions recorded in high-deposition rate lakebeds, and less often in volcanic piles, trace simple "there-and-back" paths away from and returning to the ordinary geomagnetic secular variation locus for an age. By contrast, the Sierra Libre magnetizations wander erratically in declination and inclination, without following a simple sequential ''Path''. Polarity reversal transitions recorded in high-deposition rate lakebeds do behave that way. We therefore interpret TSF (and remarkably

  9. Microcrystalline dolomite within massive Japan Sea methane hydrate: origin and development ascertained by inclusions within inclusions.

    Science.gov (United States)

    Snyder, G. T.; Kakizaki, Y.; Matsumoto, R.; Suzuki, Y.; Takahata, N.; Sano, Y.; Tanaka, K.; Tomaru, H.; Imajo, T.; Iguchi, A.

    2017-12-01

    Microcrystalline dolomite grains were recently discovered as inclusions within relatively pure massive gas hydrate recovered from the Joetsu Basin area of the Japan Sea. These grains presumably formed as a consequence of the highly saline conditions in fluid inclusions which developed between coalescing grain boundaries within the growing hydrate. Stable carbon and oxygen isotopic composition of the dolomite is consistent with crystal growth occurring within such fluids. In addition to stable isotopes, we investigate trends in Mg/Ca ratios of the grains as well as the composition of inclusions which exist within the dolomites. Preliminary research shows that these inclusions retain valuable information as to the conditions which existed at the time of formation, as well as the dynamics of these extensive hydrate deposits over time. This study was conducted under the commission from AIST as a part of the methane hydrate research project funded by METI (the Ministry of Economy, Trade and Industry, Japan).

  10. Roadmap for Inclusive Innovation

    Data.gov (United States)

    Allegheny County / City of Pittsburgh / Western PA Regional Data Center — The Roadmap for Inclusive Innovation data set shares the status of action items under the Roadmap for Inclusive Innovation. Each action or project has been assigned...

  11. Teachers becoming inclusive practitioners

    African Journals Online (AJOL)

    , construct their identities in the light of inclusive education, and how they negotiate the tensions and contradictions emerging from the processof becoming inclusive practitioners. Central to this discussion is the understanding that teachers' ...

  12. Foresighting for Inclusive Development

    DEFF Research Database (Denmark)

    Andersen, Allan Dahl; Andersen, Per Dannemand

    2017-01-01

    We propose that foresight can contribute to inclusive development by making innovation systems more inclusive. Processes of developing future oriented innovation policies are often unsuccessful and rarely inclusive. We conceptualize such processes as foresighting. We focus on how the ex-ante desi...... in foresight cases in two emerging economies: Brazil and South Korea. We conclude that better systemic and innovation oriented foresight is needed to enhance inclusive development....

  13. Inclusion: Conceptualization and measurement

    NARCIS (Netherlands)

    Jansen, W.S.; Otten, S.; Van der Zee, K.I.; Jans, L.

    2014-01-01

    n the present research, we introduced a conceptual framework of inclusion and subsequently used this as a starting point to develop and validate a scale to measure perceptions of inclusion. Departing from existing work on inclusion and complementing this with theoretical insights from optimal

  14. Inclusion: Conceptualization and measurement

    NARCIS (Netherlands)

    Jansens, Wiebren S.; Otten, Sabine; van der Zee, Karen; Jans, Lise

    2014-01-01

    In the present research, we introduced a conceptual framework of inclusion and subsequently used this as a starting point to develop and validate a scale to measure perceptions of inclusion. Departing from existing work on inclusion and complementing this with theoretical insights from optimal

  15. Inclusion : Conceptualization and measurement

    NARCIS (Netherlands)

    Jansen, Wiebren S.; Otten, Sabine; van der Zee, Karen I.; Jans, Lise

    In the present research, we introduced a conceptual framework of inclusion and subsequently used this as a starting point to develop and validate a scale to measure perceptions of inclusion. Departing from existing work on inclusion and complementing this with theoretical insights from optimal

  16. Inclusion : Conceptualization and measurement

    NARCIS (Netherlands)

    Jansen, Wiebren S.; Otten, Sabine; van der Zee, Karen I.; Jans, Lise

    2014-01-01

    In the present research, we introduced a conceptual framework of inclusion and subsequently used this as a starting point to develop and validate a scale to measure perceptions of inclusion. Departing from existing work on inclusion and complementing this with theoretical insights from optimal

  17. The Full Inclusion Movement.

    Science.gov (United States)

    Machado, Rodney E.; And Others

    1996-01-01

    Overviews background of the movement toward full inclusion of special education students into regular classrooms, including legal issues and successful educational practices. Suggests that full inclusion does not benefit all students and that inclusion should be one of several alternatives to meeting students' educational needs. Of approximately…

  18. Footstep towards Inclusive Education

    Science.gov (United States)

    Abbas, Faiza; Zafar, Aneeka; Naz, Tayyaba

    2016-01-01

    Inclusive education is a rising trend in the world. The first step towards inclusive education is providing the awareness to the general education teachers. This study focused to investigate the general education teachers of primary and secondary level awareness about the special education and inclusive education. This study is descriptive method…

  19. Documenting Your Inclusion Efforts.

    Science.gov (United States)

    Fritz, Marie F.; Miller, Maury

    This paper briefly addresses critical issues in documenting studies of the effectiveness of inclusive education for students with disabilities and includes a summary table of the existing literature and guidelines for problem solving about inclusion. The importance of sound methodology in documenting effects of inclusion and the dangers of value…

  20. Annual Layers at Siple Dome, Antarctica, from Borehole Optical Stratigraphy, Version 1

    Data.gov (United States)

    National Aeronautics and Space Administration — Researchers gathered data on annual snow layers at Siple Dome, Antarctica, using borehole optical stratigraphy. This data set contains annual layer depths and firn...

  1. Genetic stratigraphy of Coniacian deltaic deposits of the northwestern part of the Bohemian Cretaceous Basin

    Czech Academy of Sciences Publication Activity Database

    Nádaskay, R.; Uličný, David

    2014-01-01

    Roč. 165, č. 4 (2014), s. 547-575 ISSN 1860-1804 Institutional support: RVO:67985530 Keywords : genetic stratigraphy * well log * Bohemian Cretaceous Basin Subject RIV: DB - Geology ; Mineralogy Impact factor: 0.569, year: 2014

  2. Foresighting for Inclusive Development

    DEFF Research Database (Denmark)

    Dahl Andersen, Allan; Andersen, Per Dannemand

    We propose that foresight can contribute to inclusive development by making innovation policy processes more inclusive, which in turn makes innovation systems more inclusive. Processes of developing future-oriented innovation policies are often unsuccessful and rarely inclusive. We conceptualize...... and transform innovation systems because a set of distributed actors, rather than ministries and innovation agencies, is the gatekeepers of change. From this perspective, inclusion is a precondition rather than an obstacle for transformation. We develop a conceptual framework and use it to study design...

  3. cyclostratigraphy, sequence stratigraphy and organic matter accumulation mechanism

    Science.gov (United States)

    Cong, F.; Li, J.

    2016-12-01

    The first member of Maokou Formation of Sichuan basin is composed of well preserved carbonate ramp couplets of limestone and marlstone/shale. It acts as one of the potential shale gas source rock, and is suitable for time-series analysis. We conducted time-series analysis to identify high-frequency sequences, reconstruct high-resolution sedimentation rate, estimate detailed primary productivity for the first time in the study intervals and discuss organic matter accumulation mechanism of source rock under sequence stratigraphic framework.Using the theory of cyclostratigraphy and sequence stratigraphy, the high-frequency sequences of one outcrop profile and one drilling well are identified. Two third-order sequences and eight fourth-order sequences are distinguished on outcrop profile based on the cycle stacking patterns. For drilling well, sequence boundary and four system tracts is distinguished by "integrated prediction error filter analysis" (INPEFA) of Gamma-ray logging data, and eight fourth-order sequences is identified by 405ka long eccentricity curve in depth domain which is quantified and filtered by integrated analysis of MTM spectral analysis, evolutive harmonic analysis (EHA), evolutive average spectral misfit (eASM) and band-pass filtering. It suggests that high-frequency sequences correlate well with Milankovitch orbital signals recorded in sediments, and it is applicable to use cyclostratigraphy theory in dividing high-frequency(4-6 orders) sequence stratigraphy.High-resolution sedimentation rate is reconstructed through the study interval by tracking the highly statistically significant short eccentricity component (123ka) revealed by EHA. Based on sedimentation rate, measured TOC and density data, the burial flux, delivery flux and primary productivity of organic carbon was estimated. By integrating redox proxies, we can discuss the controls on organic matter accumulation by primary production and preservation under the high-resolution sequence

  4. The Relationship between Dynamic Topography and Sequence Stratigraphy

    Science.gov (United States)

    White, N. J.

    2014-12-01

    An evolving pattern of convective circulation within the mantle generates and maintains dynamic topography which is some fraction of observed topography. Spatial variations of dynamic topography are easy to measure within the oceanic realm and it is possible to exploit inventories of seismic reflection and wide-angle data to determine the dynamic topography of the oldest oceanic lithosphere that abuts passive continental margins. Results show that oceanic lithosphere has dynamic topographic anomalies of +/- 1 km with wavelengths of 500-1000 km. These substantial anomalies intersect coastal shelves and so it is expected that the development of these anomalies has affected sequence stratigraphic architecture in important ways. A series of examples will be used to illustrate how sequence stratigraphy can be profoundly influenced by changing patterns of dynamic topography. First, along the West African margin a set of dynamic topographic domes intersect the shelf edge. Onshore, the Neogene growth of these domes is recorded by emergent terraces and by drainage patterns. Offshore, an Oligo-Miocene switch from aggradation to progradation together with a series of younger disconformities have modified stratigraphic architecture along the shelf. Secondly, along the Northwest Shelf of Australia there is evidence for 700 m of dynamic drawdown of the oldest oceanic floor. Regional mapping and backstripping of clinoformal geometries within a Miocene carbonate reef complex shows that there is a dramatic switch from progradation to aggradation which cannot be attributed to glacio-eustatic variations. Instead, this switch appears to reflect growth of dynamic drawdown within the mantle. Finally, the Icelandic plume has controlled vertical motions along fringing North Atlantic margins over the last 60 Ma. Thanks to the intersecting mid-oceanic ridge, there is independent evidence that the temperature structure of this plume has fluctuated through time. These fluctuations are

  5. INCLUSIVE EDUCATION IN ITALY

    OpenAIRE

    Voitkāne, Vita

    2017-01-01

    European member States implement Inclusive Education policies thus contributing to a sustainable, inclusive society, although each country is at a different stage in this process. Italy, one of the first countries to launch integrative learning, has set an example since the 1970s, although the quality of inclusive education is unpredictable due to many issues. Authors Cantoni and Panetta (2006) emphasize that, although the culture of integration in Italy exists, much needs to be done to impro...

  6. SUPPORT IN INCLUSIVE EDUCATION

    OpenAIRE

    Belma Čičkušić; Ševala Tulumović; Selma Bakić; Salem Bakić

    2016-01-01

    In order for inclusive class to be successful, associates are of great help to teachers. Besides associates, teachers' specialization can be accomplished through educational seminars on the inclusion topic. However, information about inclusion, working with children with special needs, can also be found in scientific journals that offer more information on methods of working with children with special needs, didactic materials customized according to abilities of children. Aim of ...

  7. Ediacaran and Cambrian stratigraphy in Estonia: an updated review

    Directory of Open Access Journals (Sweden)

    Tõnu Meidla

    2017-06-01

    Full Text Available Previous late Precambrian and Cambrian correlation charts of Estonia, summarizing the regional stratigraphic nomenclature of the 20th century, date back to 1997. The main aim of this review is updating these charts based on recent advances in the global Precambrian and Cambrian stratigraphy and new data from regions adjacent to Estonia. The term ‘Ediacaran’ is introduced for the latest Precambrian succession in Estonia to replace the formerly used ‘Vendian’. Correlation with the dated sections in adjacent areas suggests that only the latest 7–10 Ma of the Ediacaran is represented in the Estonian succession. The gap between the Ediacaran and Cambrian may be rather substantial. The global fourfold subdivision of the Cambrian System is introduced for Estonia. The lower boundary of Series 2 is drawn at the base of the Sõru Formation and the base of Series 3 slightly above the former lower boundary of the ‘Middle Cambrian’ in the Baltic region, marked by a gap in the Estonian succession. The base of the Furongian is located near the base of the Petseri Formation.

  8. Alaskan Peninsula Cenozoic stratigraphy: stratigraphic sequences and current research

    Energy Technology Data Exchange (ETDEWEB)

    Allison, R.C.; Armentrout, J.M.

    1985-04-01

    Geology of the Alaska Peninsula-Island Arc and Continental Margin, by C.A. Burk, is the principal reference for stratigraphic studies on the Alaska Peninsula. Burk mapped the Phanerozoic stratigraphy and provided a geologic history and structural interpretation of the area between Wide Bay and Unimak Island. Cenozoic rocks were mapped as three unconformity-bounded sequences. Recognition of specific formations was difficult due to similarity of lithofacies, isolated outcrops, rapid facies changes, and alteration and burial by young volcanics. Consequently, megafossil assemblages were relied upon to facilitate correlations between study areas. The three unconformity-bounded Cenozoic sequences are: (1) the Paleogene Beaver Bay Group consisting of three formations: the dominantly nonmarine Tolstoi Formation, the dominantly marine Stepovak Formation, and the volcanic Meshik Formation. Current work suggests these units are at least in part coeval facies of late Paleocene through Oligocene age. (2) The Neogene Bear Lake Formation consisting of the lower Unga Conglomerate Member and an unnamed upper member. Rapid facies changes and incorrect reports of fossil occurrence have resulted in confusion of stratigraphic relationships within this sequence of middle to late Miocene age. (3) A late Neogene informally defined upper sequence consisting of interbedded marginal marine, coastal-plain, and volcanic facies. Current work suggests this sequence is Pliocene through Pleistocene in age.

  9. Contribution to the stratigraphy of the onshore Paraiba Basin, Brazil

    Energy Technology Data Exchange (ETDEWEB)

    Rossetti, Dilce F.; Valeriano, Marcio M., E-mail: rossetti@dsr.inpe.br [Instituto Nacional de Pesquisas Espaciais (INPE), Sao Jose dos Campos, SP (Brazil). Divisao de Sensoriamento Remoto; Goes, Ana M.; Brito-Neves, Benjamim B. [Universidade de Sao Paulo (USP), Sao Paulo, SP (Brazil). Inst. de Geociencias; Bezerra, Francisco H.R.; Ochoa, Felipe L. [Universidade Federal do Rio Grande do Norte (UFRN), Natal, RN (Brazil). Centro de Ciencias Exatas e da Terra. Departamento de Geologia

    2012-06-15

    Several publications have contributed to improve the stratigraphy of the Paraiba Basin in northeastern Brazil. However, the characterization and distribution of sedimentary units in onshore areas of this basin are still incomplete, despite their significance for reconstructing the tectono- sedimentary evolution of the South American passive margin. This work provides new information to differentiate among lithologically similar strata, otherwise entirely unrelated in time. This approach included morphological, sedimentological and stratigraphic descriptions based on surface and sub-surface data integrated with remote sensing, optically stimulated luminescence dating, U+Th/He dating of weathered goethite, and heavy mineral analysis. Based on this study, it was possible to show that Cretaceous units are constrained to the eastern part of the onshore Paraiba Basin. Except for a few outcrops of carbonatic-rocks nearby the modern coastline, deposits of this age are not exposed to the surface in the study area. Instead, the sedimentary cover throughout the basin is constituted by mineralogically and chronologically distinctive deposits, inserted in the Barreiras Formation and mostly in the Post-Barreiras Sediments, of early/middle Miocene and Late Pleistocene-Holocene ages, respectively. The data presented in this work support tectonic deformation as a factor of great relevance to the distribution of the sedimentary units of the Paraiba Basin. (author)

  10. Investigations on alluvial deposits through borehole stratigraphy, radiocarbon dating and passive seismic technique (Carnic Alps, NE Italy)

    Science.gov (United States)

    Viero, Alessia; Marchi, Lorenzo; Cavalli, Marco; Crema, Stefano; Fontana, Alessandro; Mozzi, Paolo; Venturini, Corrado

    2016-04-01

    Alluvial sediment investigations provide fundamental tools to infer the processes that control geomorphological evolution of mountain environments. By analyzing sediment stratigraphy in depth, it is possible to retrieve the source, the geology, the time of deposition, the relative distance travelled by material as well as to distinguish among different type of transport (i.e., gravitational, fluvial or glacial). In this work, we present a combination of log stratigraphy, radiocarbon dating and geophysical surveys carried out on the valley floor of the But River (Carnic Alps, North East Italy). The But River basin drains an area of 326 km2 with a range in elevation from 2769 to 323 m a.s.l.; the bedrock mainly consists of carbonates and quartz arenites with minor inclusions of effusive rocks. After Pleistocene the gravitational deposits from mountain slopes have impounded the But River several times. In particular, we analyzed a sector of the upper portion of the But valley close to the confluence of the Moscardo Torrent, frequently affected by debris flows. A borehole was drilled in the But River floodplain, at the intersection with the Moscardo Torrent alluvial fan, down to a depth of 80 m. The analysis of the core samples allowed discerning three sedimentary levels rich in clay and organic materials, which testify the presence of small dam lakes, originated from the Moscardo debris-flow deposits. Three samples of wood and plant debris were collected from 13, 14 and 23 m of depth, respectively. They were analyzed through radiocarbon dating in order to determine the age of the lakes and, thus, to infer the activity of the debris flows building the Moscardo cone. The calibrated ages of the 3 samples are close to the younger limit of the radiocarbon method indicating a fast aggradation of the valley floor, starting from a period ranging between 1450 - 1632 AD. Historical maps and documents confirm the presence of the lakes until 19th century and they permit to assess

  11. Confronting New Demands : Inclusive Growth, Inclusive Trade ...

    International Development Research Centre (IDRC) Digital Library (Canada)

    The research agenda will cover four themes: linkages between trade and inclusive growth; negotiation issues with poorly understood implications, such as labour standards and intellectual property; liberalization of trade in services, and the emerging regional trade policy architecture. The idea is to promote a better ...

  12. Understanding Inclusion in Cyprus

    Science.gov (United States)

    Mamas, Christoforos

    2013-01-01

    This paper provides a framework for understanding inclusion in Cyprus. The evidence base is the result of a six-month qualitative research study in five Cypriot mainstream primary schools. Despite the rhetoric in favour of inclusion, it seems that the Cypriot educational system is still highly segregating in its philosophy and does not fully…

  13. School Inclusion Programmes (SIPS)

    Science.gov (United States)

    Drossinou-Korea, Maria; Matousi, Dimitra; Panopoulos, Nikolaos; Paraskevopoulou, Aikaterini

    2016-01-01

    The purpose of this work was to understand the school inclusion programmes (SIPs) for students with special educational needs (SEN). The methodology was conducted in the field of special education (SE) and focuses on three case studies of students who was supported by SIPs. The Targeted, Individual, Structured, Inclusion Programme for students…

  14. Fluid Mechanics.

    Science.gov (United States)

    Drazin, Philip

    1987-01-01

    Outlines the contents of Volume II of "Principia" by Sir Isaac Newton. Reviews the contributions of subsequent scientists to the physics of fluid dynamics. Discusses the treatment of fluid mechanics in physics curricula. Highlights a few of the problems of modern research in fluid dynamics. Shows that problems still remain. (CW)

  15. Fluid Interfaces

    DEFF Research Database (Denmark)

    Hansen, Klaus Marius

    2001-01-01

    Fluid interaction, interaction by the user with the system that causes few breakdowns, is essential to many user interfaces. We present two concrete software systems that try to support fluid interaction for different work practices. Furthermore, we present specificity, generality, and minimality...... as design goals for fluid interfaces....

  16. Ladle Metallurgy Kinetics: Inclusion-Inclusion Reactions

    Science.gov (United States)

    Pistorius, P. Chris

    An example is presented to illustrate the joint effect of local reaction equilibria and mass transfer limitations, for reactions during ladle refining of steel. The example relies on some of the kinetic principles that David Robertson has employed to quantify many metallurgical processes. In calcium treatment of alumina inclusions in aluminum-killed steels, solid CaS forms as an intermediate reaction product. During subsequent reaction, CaS disappears and calcium aluminate forms; at the same time, aluminum and sulfur dissolve in the steel. Kinetic analysis shows that the rate of this reaction is not limited by mass transfer of dissolved aluminum and sulfur away from the reacting inclusions. The reaction rate is likely limited by transport of dissolved calcium. This example also illustrates the use of FactSage macros for kinetic modeling.

  17. Fluid dynamics of dilatant fluid

    DEFF Research Database (Denmark)

    Nakanishi, Hiizu; Nagahiro, Shin-ichiro; Mitarai, Namiko

    2012-01-01

    A dense mixture of granules and liquid often shows a severe shear thickening and is called a dilatant fluid. We construct a fluid dynamics model for the dilatant fluid by introducing a phenomenological state variable for a local state of dispersed particles. With simple assumptions for an equation...

  18. Digital Stratigraphy: Contextual Analysis of File System Traces in Forensic Science.

    Science.gov (United States)

    Casey, Eoghan

    2017-12-28

    This work introduces novel methods for conducting forensic analysis of file allocation traces, collectively called digital stratigraphy. These in-depth forensic analysis methods can provide insight into the origin, composition, distribution, and time frame of strata within storage media. Using case examples and empirical studies, this paper illuminates the successes, challenges, and limitations of digital stratigraphy. This study also shows how understanding file allocation methods can provide insight into concealment activities and how real-world computer usage can complicate digital stratigraphy. Furthermore, this work explains how forensic analysts have misinterpreted traces of normal file system behavior as indications of concealment activities. This work raises awareness of the value of taking the overall context into account when analyzing file system traces. This work calls for further research in this area and for forensic tools to provide necessary information for such contextual analysis, such as highlighting mass deletion, mass copying, and potential backdating. © 2017 American Academy of Forensic Sciences.

  19. Integrated stratigraphy and paleoenvironmental reconstruction for the Late Cretaceous Danish chalk based on the Stevns-2 core

    DEFF Research Database (Denmark)

    Boussaha, Myriam; Thibault, Nicolas Rudolph; Stemmerik, Lars

    An integrated stratigraphy of the Stevns-2 core located in eastern Denmark is hereby presented based on calcareous nannofossil biostratigraphy and carbon isotope stratigraphy. Carbon and oxygen isotope have been performed on 419 bulk samples. Calcareous nannofossil biostratigraphy has been applie...

  20. Research on the bio-stratigraphy. Stratigraphy and paleontology of the Cretaceous sedimentary strata in the Youngdong basin

    Energy Technology Data Exchange (ETDEWEB)

    Choi, Sung Ja; Kim, Yoo Bong; Kim, Bok Chul [Korea Institute of Geology Mining and Materials, Taejon (Korea, Republic of)

    1995-12-01

    The Youngdong Basin developed at the eastern margin of the Okcheon Orogenic Belt is in contact with the Yongnam Massif by the Youngdong Fault. This study deals with tectonic setting, sedimentological, pale-ontological study of the Youngdong Basin. Concerned with the formation of the basin, left lateral movement of the Ogdong and Youngdong faults gave a major role for the development of the Youngdong Basin. The Youngdong Basin is tectonically subdivided into three parts (north, center, and south) on the basis of bedding form line and fracture patterns. Sedimentological study is concentrated in the southern part of the basin in order to establish stratigraphy in this area. The Mangyeri Formation is characterized by the deposit of debris flow and hyper-concentrated flow deposits developed at the steep gradient fan-delta slope and on alluvial fan along the southern basin margin. On the other hand, the formation in northern part of the basin is deposited in alluvial fan and braided rivers. The Gadongri Formation is mostly deposited by the process of turbidity current and density under current in lacustrine environment, and the Dongjongri Formation comprises alluvial fan and braided river sediments which mostly deposited by debris flow, hyper-concentrated flood flow, sheet flood and stream flow. For paleontology, ostracodes and charophytes are yielded from the Gadongri, Dongjongri and Sonyoudong formations. On the basis of fossils, the Dongjongri formation is correlated with the Iljig Formation of the Euisung basin, the Sonyoudong formation is correlated with the Songnaedong and Geonchunri formations of the Milyang basin. Consequently, the Mangyeri and Gadongri formations are correlated with the Sindong Group, the Dongjongri and Sonyoudong formations are correlated with the Hayang Group. (author). 47 refs., 5 tabs.

  1. Fluids engineering

    International Nuclear Information System (INIS)

    Anon.

    1991-01-01

    Fluids engineering has played an important role in many applications, from ancient flood control to the design of high-speed compact turbomachinery. New applications of fluids engineering, such as in high-technology materials processing, biotechnology, and advanced combustion systems, have kept up unwaining interest in the subject. More accurate and sophisticated computational and measurement techniques are also constantly being developed and refined. On a more fundamental level, nonlinear dynamics and chaotic behavior of fluid flow are no longer an intellectual curiosity and fluid engineers are increasingly interested in finding practical applications for these emerging sciences. Applications of fluid technology to new areas, as well as the need to improve the design and to enhance the flexibility and reliability of flow-related machines and devices will continue to spur interest in fluids engineering. The objectives of the present seminar were: to exchange current information on arts, science, and technology of fluids engineering; to promote scientific cooperation between the fluids engineering communities of both nations, and to provide an opportunity for the participants and their colleagues to explore possible joint research programs in topics of high priority and mutual interest to both countries. The Seminar provided an excellent forum for reviewing the current state and future needs of fluids engineering for the two nations. With the Seminar ear-marking the first formal scientific exchange between Korea and the United States in the area of fluids engineering, the scope was deliberately left broad and general

  2. A Geostatistical Toolset for Reconstructing Louisiana's Coastal Stratigraphy using Subsurface Boring and Cone Penetrometer Test Data

    Science.gov (United States)

    Li, A.; Tsai, F. T. C.; Jafari, N.; Chen, Q. J.; Bentley, S. J.

    2017-12-01

    A vast area of river deltaic wetlands stretches across southern Louisiana coast. The wetlands are suffering from a high rate of land loss, which increasingly threats coastal community and energy infrastructure. A regional stratigraphic framework of the delta plain is now imperative to answer scientific questions (such as how the delta plain grows and decays?) and to provide information to coastal protection and restoration projects (such as marsh creation and construction of levees and floodwalls). Through years, subsurface investigations in Louisiana have been conducted by state and federal agencies (Louisiana Department of Natural Resources, United States Geological Survey, United States Army Corps of Engineers, etc.), research institutes (Louisiana Geological Survey, LSU Coastal Studies Institute, etc.), engineering firms, and oil-gas companies. This has resulted in the availability of various types of data, including geological, geotechnical, and geophysical data. However, it is challenging to integrate different types of data and construct three-dimensional stratigraphy models in regional scale. In this study, a set of geostatistical methods were used to tackle this problem. An ordinary kriging method was used to regionalize continuous data, such as grain size, water content, liquid limit, plasticity index, and cone penetrometer tests (CPTs). Indicator kriging and multiple indicator kriging methods were used to regionalize categorized data, such as soil classification. A compositional kriging method was used to regionalize compositional data, such as soil composition (fractions of sand, silt and clay). Stratigraphy models were constructed for three cases in the coastal zone: (1) Inner Harbor Navigation Canal (IHNC) area: soil classification and soil behavior type (SBT) stratigraphies were constructed using ordinary kriging; (2) Middle Barataria Bay area: a soil classification stratigraphy was constructed using multiple indicator kriging; (3) Lower Barataria

  3. Evidence on Inclusion

    DEFF Research Database (Denmark)

    Dyssegaard, Camilla Brørup; Larsen, Michael Søgaard

    The purpose of this publication is to examine existing research on inclusion to identify strategies of inclusion that have generated positive effects. To do so it is necessary to understand the effect of the applied strategies. One approach, which is being discussed, is to use evidence to determine...... which methods have proven more effective than others. The desire to gain insight into research on inclusion forms the basis of the current systematic review. The task was to determine which strategies primary research has found to be most effective for inclusion purposes. We have solved this task...... by addressing the existing research with the following question: What is the effect of including children with special needs in mainstream teaching in basic school, and which of the applied educational methods have proved to have a positive effect?...

  4. Fluid-fluid level on MR image: significance in Musculoskeletal diseases

    Energy Technology Data Exchange (ETDEWEB)

    Chung, Hye Won; Lee, Kyung Won [Seoul Naitonal University, Seoul (Korea, Republic of). Coll. of Medicine; Song, Chi Sung [Seoul City Boramae Hospital, Seoul (Korea, Republic of); Han, Sang Wook; Kang, Heung Sik [Seoul Naitonal University, Seoul (Korea, Republic of). Coll. of Medicine

    1998-01-01

    To evaluate the frequency, number and signal intensity of fluid-fluid levels of musculoskeletal diseases on MR images, and to determine the usefulness of this information for the differentiation of musculoskeletal diseases. MR images revealed fluid-fluid levels in the following diseases : giant cell tumor(6), telangiectatic osteosarcoma(4), aneurysmal bone cyst(3), synovial sarcoma(3), chondroblastoma(2), soft tissue tuberculous abscess(2), hematoma(2), hemangioma (1), neurilemmoma(1), metastasis(1), malignant fibrous histiocytoma(1), bursitis(1), pyogenic abscess(1), and epidermoid inclusion cyst(1). Fourteen benign tumors and ten malignant, three abscesses, and the epidermoid inclusion cyst showed only one fluid-fluid level in a unilocular cyst. On T1-weighted images, the signal intensities of fluid varied, but on T2-weighted images, superior layers were in most cases more hyperintense than inferior layers. Because fluid-fluid layers are a nonspecific finding, it is difficult to specifically diagnose each disease according to the number of fluid-fluid levels or signal intensity of fluid. In spite of the nonspecificity of fluid-fluid levels, they were frequently seen in cases of giant cell tumor, telangiectatic osteosarcoma, aneurysmal bone cycle, and synovial sarcoma. Nontumorous diseases such abscesses and hematomas also demonstrated this finding. (author). 11 refs., 1 tab., 4 figs.

  5. Fluid-fluid level on MR image: significance in Musculoskeletal diseases

    International Nuclear Information System (INIS)

    Chung, Hye Won; Lee, Kyung Won; Han, Sang Wook; Kang, Heung Sik

    1998-01-01

    To evaluate the frequency, number and signal intensity of fluid-fluid levels of musculoskeletal diseases on MR images, and to determine the usefulness of this information for the differentiation of musculoskeletal diseases. MR images revealed fluid-fluid levels in the following diseases : giant cell tumor(6), telangiectatic osteosarcoma(4), aneurysmal bone cyst(3), synovial sarcoma(3), chondroblastoma(2), soft tissue tuberculous abscess(2), hematoma(2), hemangioma (1), neurilemmoma(1), metastasis(1), malignant fibrous histiocytoma(1), bursitis(1), pyogenic abscess(1), and epidermoid inclusion cyst(1). Fourteen benign tumors and ten malignant, three abscesses, and the epidermoid inclusion cyst showed only one fluid-fluid level in a unilocular cyst. On T1-weighted images, the signal intensities of fluid varied, but on T2-weighted images, superior layers were in most cases more hyperintense than inferior layers. Because fluid-fluid layers are a nonspecific finding, it is difficult to specifically diagnose each disease according to the number of fluid-fluid levels or signal intensity of fluid. In spite of the nonspecificity of fluid-fluid levels, they were frequently seen in cases of giant cell tumor, telangiectatic osteosarcoma, aneurysmal bone cycle, and synovial sarcoma. Nontumorous diseases such abscesses and hematomas also demonstrated this finding. (author). 11 refs., 1 tab., 4 figs

  6. Mapping Inclusive Growth

    OpenAIRE

    Raquel Almeida Ramos; Rafael Ranieri; Jan-Willem Lammes

    2013-01-01

    Since its emergence around the turn of the century the concept of inclusive growth has been substantially debated by researchers and practitioners, has increasingly gained space in domestic and international political circles, has inspired the design of and generated projects and policies, and has impacted the views and the lives of many people. While the conceptual debate and the practical application of various definitions of inclusive growth have taken place simultaneously, they have recen...

  7. RISKS OF INCLUSIVE EDUCATION

    OpenAIRE

    M. R. Husnutdinova

    2017-01-01

    Introduction. Inclusion is a new and unfamiliar phenomenon for most of the Russians which is treated as ensuring equal access to education for all students taking into account a variety of their special educational needs and individual capabilities. Inclusive educational model began to take root in Russia without a broad public debate and today’s parents and teachers were not ready to the cardinal changes caused by transition to the new model of education. In this regard, the studying of dire...

  8. Limitations of inclusive fitness.

    Science.gov (United States)

    Allen, Benjamin; Nowak, Martin A; Wilson, Edward O

    2013-12-10

    Until recently, inclusive fitness has been widely accepted as a general method to explain the evolution of social behavior. Affirming and expanding earlier criticism, we demonstrate that inclusive fitness is instead a limited concept, which exists only for a small subset of evolutionary processes. Inclusive fitness assumes that personal fitness is the sum of additive components caused by individual actions. This assumption does not hold for the majority of evolutionary processes or scenarios. To sidestep this limitation, inclusive fitness theorists have proposed a method using linear regression. On the basis of this method, it is claimed that inclusive fitness theory (i) predicts the direction of allele frequency changes, (ii) reveals the reasons for these changes, (iii) is as general as natural selection, and (iv) provides a universal design principle for evolution. In this paper we evaluate these claims, and show that all of them are unfounded. If the objective is to analyze whether mutations that modify social behavior are favored or opposed by natural selection, then no aspect of inclusive fitness theory is needed.

  9. Fluid machinery

    International Nuclear Information System (INIS)

    Ha, Jae Hyeon; Son, Byeong Jin

    2001-04-01

    This book tells of definition and classification of fluid machinery, energy equation of incompressible fluid, principle of momentum, classification and structure of pump, size, safety of centrifugal pump, theory and operation of contraction pump, reciprocating pump, rotary pump, special pump, using of water power, classification of water turbine, impulse water turbine, reaction water turbine, pump water turbine, liquid movement apparatus, fluid type control machinery and solid and gas type pneumatic machine.

  10. RISKS OF INCLUSIVE EDUCATION

    Directory of Open Access Journals (Sweden)

    M. R. Husnutdinova

    2017-01-01

    Full Text Available Introduction. Inclusion is a new and unfamiliar phenomenon for most of the Russians which is treated as ensuring equal access to education for all students taking into account a variety of their special educational needs and individual capabilities. Inclusive educational model began to take root in Russia without a broad public debate and today’s parents and teachers were not ready to the cardinal changes caused by transition to the new model of education. In this regard, the studying of directly educational process by consequences of inclusive training and education is urgent now.The aims of the research are the following: to identify the major risks that characterize the current stage of the implementation process of inclusion in the Russian educational organizations; to consider the main causes that lead to their occurrence; to present a comparative analysis of the views of respondents in comprehensive, inclusive and correctional schools. Methodology and research methods. The Sector Monitoring Studies of Moscow State University of Psychology & Education in 2010 and 2014 implemented a sociological study on the process of introduction of inclusion in the Russian schools. 200 teachers and 244 parents were interviewed in 2010; in 2014, in addition, 178 teachers and 386 parents were interviewed; 47 senior students including those with disabilities were interviewed too.Results. According to the results, the main concerns of the parents of students of comprehensive, inclusive and correctional schools are reduced to a few basic risks: lack of individual approach while teaching children with different educational needs, increased emotional pressure on the child, and child’s perception of the complexity of disability as an equal. These risks arise primarily because of the acute shortage of especially prepared-governmental teachers and socio-cultural, psychological unpreparedness of most contemporary children with disabilities to the perception of

  11. Schroedinger fluid

    International Nuclear Information System (INIS)

    Kan, K.K.

    1983-01-01

    The relationship of nuclear internal flow and collective inertia, the difference of this flow from that of a classical fluid, and the approach of this flow to rigid flow in independent-particle model rotation are elucidated by reviewing the theory of Schroedinger fluid and its implications for collective vibration and rotation. (author)

  12. Fluid Dynamics

    DEFF Research Database (Denmark)

    Brorsen, Michael

    These lecture notes are intended mainly for the 7th semester course "Fluid Dynamics" offered by the Study Committee on Civil Engineering, Aalborg University.......These lecture notes are intended mainly for the 7th semester course "Fluid Dynamics" offered by the Study Committee on Civil Engineering, Aalborg University....

  13. Lower Devonian Brachiopods and Stratigraphy of North Palencia (Cantabrian Mountains, Spain)

    NARCIS (Netherlands)

    Binnekamp, J.G.

    1965-01-01

    A continuous sequence of Devonian sediments is exposed in the northern part of the province of Palencia (NW-Spain), on the southern slope of the Cantabrian Mountains. This study concerns the stratigraphy and paleontology of the Lower Devonian formations. At the base of the sequence a clastic

  14. Three-dimensional modelling of thrust-controlled foreland basin stratigraphy

    NARCIS (Netherlands)

    Clevis, Q. (Quintijn)

    2003-01-01

    In this thesis a tectono-sedimentary forward model has been presented, devised to simulate sediment erosion and deposition in a coupled drainage basin - foreland system, as well as accumulating a three-dimensional stratigraphy. The aim of the research was to investigate which features recorded in

  15. Review of the Upper Jurassic-Lower Cretaceous stratigraphy in Western Cameros basin, Northern Spain

    DEFF Research Database (Denmark)

    Vidal, Maria del Pilar Clemente

    2010-01-01

    The Upper Jurassic-Lower Cretaceous stratigraphy of the Cameros basin has been reviewed. In Western Cameros the stratigraphic sections are condensed but they have a parallel development with the basin depocentre and the same groups have been identified. The Tera Group consists of two formations: ...

  16. Seismic stratigraphy and depositional history of the Büyükçekmece ...

    Indian Academy of Sciences (India)

    Denizhan Vardar

    2018-02-14

    Feb 14, 2018 ... with decreased sediment input and smaller accommodation space. Keywords. Büyükçekmece bay; seismic stratigraphy; sea level changes; prograding shoreline; incised valley; Bosphorus strait. 1. Introduction. The Marmara Sea is an intra-continental marine basin connected to the adjacent seas via the.

  17. Late Quaternary stratigraphy and depositional history of the Long Island Sound basin

    Science.gov (United States)

    Lewis, Ralph S.; Stone, Janet R.

    1991-01-01

    The stratigraphy of Late Quaternary geologic units beneath Long Island Sound (LIS) is interpreted from 3,500 km of high-resolution, seismic-reflection profiles supplemented by vibracore data. Knowledge gained from onshore regional geologic studies and previous offshore investigations is also incorporated in these interpretations.

  18. Study of Meteoritic Inclusion

    DEFF Research Database (Denmark)

    Olsen, Mia Bjørg Stolberg

    ionization mass spectrometry (SIMS). Moreover, we have shown that combining careful petrological investigations with high-precision isotope measurements of multiple systems on single meteoritic inclusions can potentially provide unique insights into the formation history of the solar system's earliest solids...... and the observation of a reduced initial abundance of 26Al in the accretion regions of chondrules and asteroidal bodies impacts our understanding of the accretion timescales of protoplanets in a significant way. Combining high-precision isotope measurements of multiple systems on individual meteoritic inclusions...

  19. Creative activity and inclusion

    Directory of Open Access Journals (Sweden)

    Shemanov A.Yu.

    2013-09-01

    Full Text Available The aim of the article was to analyze the inclusion potential of art creative activity, namely of theatre performance, in people with disabilities. The article provides examples of disagreements in understanding the significance of these art activities for exercising the rights of people with disabilities to contribute to culture and art and some problems arising here. The conclusion is made that theatre art performed by people with disabilities is gradually changing its function: from being a means of self-affirmation to the determination of its specific place in overall theatre process. These changes confirm the inclusion potential of theatre art activity.

  20. Lead inclusions in aluminium

    International Nuclear Information System (INIS)

    Johnson, E.; Johansen, A.; Sarholt-Kristensen, L.; Andersen, H.H.; Grabaek, L.; Bohr, J.

    1990-01-01

    Ion implantation at room temperature of lead into aluminum leads to spontaneous phase separation and formation of lead precipitates growing topotactically with the matrix. Unlike the highly pressurized (∼ 1-5 GPa) solid inclusions formed after noble gas implantations, the pressure in the lead precipitates is found to be less than 0.12 GPa. Recently the authors have observed the result that the lead inclusions in aluminum exhibit both superheating and supercooling. In this paper they review and elaborate on these results. Small implantation-induced lead precipitates embedded in an aluminum matrix were studied by x-ray diffraction

  1. Inclusive Education in Israel

    OpenAIRE

    O. V. Mayzel

    2013-01-01

    To get acquainted with the practice of inclusive education in mainstream schools, with professionals who work with special children, to visit the specialist centers to share experiences - all of this was part of an internship program «Early Childhood Education for Children with Special Needs», held in Israel (April 8 -02 May 2013) this year. The country has been selected for an internship, because the practice of inclusive education has been used for over 20 years in Israel. Moreover, a lot ...

  2. A stratigraphy fieldtrip for people with visual impairment

    Science.gov (United States)

    Gomez-Heras, Miguel; Gonzalez-Acebron, Laura; Muñoz-Garcia, Belen; Garcia-Frank, Alejandra; Fesharaki, Omid

    2017-04-01

    This communication presents how a stratigraphy fieldtrip adapted to people with visual impairment was prepared and carried out. This fieldtrip aimed to promote scientific knowledge on Earth sciences to people with visual impairment and to inspire Earth scientists to take into account the needs of people with disabilities when designing public engagement activities. To do this, the theme chosen for the fieldtrip was the importance of sedimentary rocks shaping the Earth and what information can one extract from observing sedimentary structures. The Triassic outcrops of Riba de Santiuste (Guadalajara, Spain) were observed during this fieldtrip. The expected learning outcomes were: a) understanding what are sedimentary rocks, how they are formed and how they fold and crop out, b) knowing what is a sedimentary structure and recognising some of them and c) be able to make inferences of the sedimentary environment from certain sedimentary structures. The fieldtrip was prepared, through the NGO "Science without Barriers" together with the Madrid delegation of the National Association for Spanish Blind People (ONCE-Madrid). ONCE-Madrid was responsible of advertising this activity as a part of their yearly cultural program to its affiliate. A preparatory fieldtrip was carried out to test the teaching methodology and to make an appropriate risk assessment. This was made together with the responsible of the Culture Area of ONCE-Madrid and two blind people. The involvement of end-users in the preparation of activities is in the core of the European Disability Forum motto: "Nothing about us without us". A crucial aspect of the site was accessibility. In terms of perambulatory accessibility of outcrops the site is excellent and suitable to some extent for end-users regardless of their physical fitness. The fieldtrip itself took place on October 15th 2016 and 30 people with and without visual disability attended. In addition to overall observations and explanations of strata and

  3. Geology and Stratigraphy of Four Candidate Pyroclastic Deposits on Mercury

    Science.gov (United States)

    Weinauer, Julia; Hiesinger, Harald; Bauch, Karin; Preusker, Frank

    2016-04-01

    The MESSENGER (Mercury Surface, Space Environment, Geochemistry, and Ranging) spacecraft [1] to Mercury revealed numerous new findings, including the discovery of potential pyroclastic deposits [2-9]. Besides impact cratering, volcanic processes, including the deposition of pyroclastic materials are among the most important processes to shape the surface of a planet. Volcanic processes allow us to study the thermal evolution of the planet, and impacts provide insights into the composition of the crust, and possible the mantle. In this study we focus on four specific examples of potential pyroclastic deposits: Lermontov NE (-48.15°E, 15.80°), Lermontov SE (-49.08°E, 15.04°), Glinka (-112.42°E, 15.01°), and Unnamed crater 7 (88.20°E, 32.40°). For our investigation we used data of the Mercury Dual Imaging System (MDIS) [10]. In particular we studied narrow-angle Camera (NAC) images with a resolution of 25-100 m/pixel and wide-angle camera (WAC) images with a resolution of about 170-250 m/pixel. Our data set is complemented by Digital Terrain Models (DTM) based on photogrammetric analyses of stereo images [11]. The objectives of this study are to investigate the geologic context of the pyroclastic deposits, to map their morphological/compositional sub-units in detail, to derive volume estimates for these deposits, to study their eruption conditions, and to derive information on the timing of the emplacement of these units. In addition, absolute model ages are determined to develop a stratigraphy of the mapped units Several morphologic features were observed in association with the pyroclastic deposits, including lobate scarps, melt pools, and large irregular depressions, as well as small-scale irregularly shaped, shallow, rimless depressions, i.e., hollows [2]. In Lermontov, the large irregular depressions that can be plausibly interpreted as vent structures [6,7] occur within a roughly circular depression of about 50 km in diameter, located in the center of

  4. Developing a financial inclusion index and inclusive growth in India

    OpenAIRE

    Susanta Kumar SETHY

    2016-01-01

    Financial inclusion is one of the systems through which Inclusive Growth can be achieved in developing countries like India where large sections are unable or hopeless to contribute in the financial system. An inclusive financial system mobilizes more resources for productive purposes leading to higher economic growth, better opportunities and reduction of poverty. This study, proposed an Index of financial inclusion – a multidimensional measure. The Financial Inclusion Index c...

  5. Linguistic Diversity and Social Inclusion

    Science.gov (United States)

    Piller, Ingrid; Takahashi, Kimie

    2011-01-01

    This introduction provides the framework for the special issue by describing the social inclusion agenda of neoliberal market democracies. While the social inclusion agenda has been widely adopted, social inclusion policies are often blind to the ways in which language proficiency and language ideologies mediate social inclusion in linguistically…

  6. Assessment of inclusive education

    DEFF Research Database (Denmark)

    Miller, Tanja

    2014-01-01

    The focus of this paper is on the way teachers, in teams can work with assessing the inclusive practice in their own classes. In 2012 a joint effort between CEPRA, teachers and school administrators from the municipality of Hjørring developed a dialog based model for continually assessing the qua...

  7. Mathematics Teaching and Inclusion

    DEFF Research Database (Denmark)

    This volume contains the proceedings of the 3rd Nordic Research Conference on Special Needs Education in Mathematics, which took place in Rebild organised by Aalborg University in November 23-25, 2005. The theme of the conference was Mathematics Education and Inclusion. The conference theme...

  8. Peer Tutoring for Inclusion

    Science.gov (United States)

    Temple, Viviene A.; Lynnes, Michelle D.

    2008-01-01

    Peer tutoring is a pedagogical technique that has promise to improve outcomes for students with a disability within existing resource constraints. Published empirically-based papers on peer-tutoring were descriptively analysed. Synthesis of these studies revealed that peer tutoring is effective in inclusive physical education contexts. Evidence…

  9. Penile Epidermal Inclusion Cyst

    Directory of Open Access Journals (Sweden)

    M. El-Shazly

    2012-01-01

    Full Text Available We report a case of epidermal inclusion cyst in a 32-year-old male. This was a complication of circumcision that was neglected over years to form stones and urethrocutaneous fistula. Complete excision of the cyst and repair of the fistula were performed successfully. Histopathological examination confirmed our diagnosis.

  10. Supporting Inclusive Growth

    International Development Research Centre (IDRC) Digital Library (Canada)

    msandilands

    2010-10-27

    Oct 27, 2010 ... United Nations Development Programme. WRC. Women's Rights and Citizenship ... The goal of the Supporting Inclusive Growth (SIG) program is to support rigorous and policy-oriented research that ... Exploring synergies with IDRC's Environmental Economics program and other lead players outside the ...

  11. Multilingualism and social inclusion

    NARCIS (Netherlands)

    Marácz, L.; Adamo, S.

    2017-01-01

    This is a thematic issue on the relation between multilingualism and social inclusion. Due to globalization, Europeanization, supranational and transnational regulations linguistic diversity and multilingualism are on the rise. Migration and old and new forms of mobility play an important role in

  12. In-plane dynamics of membranes with immobile inclusions.

    Science.gov (United States)

    Oppenheimer, Naomi; Diamant, Haim

    2011-12-16

    Cell membranes are anchored to the cytoskeleton via immobile inclusions. We investigate the effect of such anchors on the in-plane dynamics of a fluid membrane and mobile inclusions (proteins) embedded in it. The immobile particles lead to a decreased diffusion coefficient of mobile ones and suppress the correlated diffusion of particle pairs. Because of the long-range, quasi-two-dimensional nature of membrane flows, these effects become significant at a low area fraction (below 1%) of immobile inclusions. © 2011 American Physical Society

  13. Anomalously metal-rich fluids form hydrothermal ore deposits.

    Science.gov (United States)

    Wilkinson, Jamie J; Stoffell, Barry; Wilkinson, Clara C; Jeffries, Teresa E; Appold, Martin S

    2009-02-06

    Hydrothermal ore deposits form when metals, often as sulfides, precipitate in abundance from aqueous solutions in Earth's crust. Much of our knowledge of the fluids involved comes from studies of fluid inclusions trapped in silicates or carbonates that are believed to represent aliquots of the same solutions that precipitated the ores. We used laser ablation inductively coupled plasma mass spectrometry to test this paradigm by analysis of fluid inclusions in sphalerite from two contrasting zinc-lead ore systems. Metal contents in these inclusions are up to two orders of magnitude greater than those in quartz-hosted inclusions and are much higher than previously thought, suggesting that ore formation is linked to influx of anomalously metal-rich fluids into systems dominated by barren fluids for much of their life.

  14. Mechanical stratigraphy of deep-water sandstones: insights from a multisciplinary field and laboratory study

    Science.gov (United States)

    Agosta, Fabrizio; di Celma, Claudio; Tondi, Emanuele; Corradetti, Amerigo; Cantalamessa, Gino

    2010-05-01

    Turbidite sandstones found in deep-water fold-and-thrust belts are increasingly exploited as hydrocarbon reservoirs. Within these rocks, the fluid flow is profoundly affected by the complex interaction between primary sedimentological and stratigraphic attributes (i.e, facies, layering, reservoir quality, stacking patterns, bed connectivity and lateral extent) and fracture characteristics (i.e., length, spacing, distribution, orientation, connectivity). Unfortunately, most of these features are at, or below, the resolution of conventional seismic datasets and, for this reason, their identification and localization represent one of the fundamental challenges facing exploration, appraisal and production of the sandstone reservoirs. In this respect, whereas considerable effort has been afforded to a characterization of the sedimentological and stratigraphic aspects of sandstones, detailed analysis of fractures in this type of successions has received significantly less attention. In this work, we combine field and laboratory analyses to assess the possible mechanical control exerted by the rock properties (grain size, intergranualr porosity, and Young modulus), as well as the influence of bed thickness, on joint density in turbidite sandstones. Joints are mode-I fractures occurring parallel to the greatest principle stress axis, which solve opening displacement and do not show evidence of shearing and enhance the values of total porosity forming preferential hydraulic conduits for fluid flow. Within layered rocks, commonly, joints form perpendicular to bedding due to overburden or exhumation. The empirical relation between joint spacing and bed thickness, documented in the field by many authors, has been mechanically related to the stress perturbation taking place around joints during their formation. Furthermore, close correlations between joint density and rock properties have been already established. In this present contribution, we focus on the bed

  15. The search for and analysis of direct samples of early Solar System aqueous fluids.

    Science.gov (United States)

    Zolensky, Michael E; Bodnar, Robert J; Yurimoto, Hisayoshi; Itoh, Shoichi; Fries, Marc; Steele, Andrew; Chan, Queenie H-S; Tsuchiyama, Akira; Kebukawa, Yoko; Ito, Motoo

    2017-05-28

    We describe the current state of the search for direct, surviving samples of early, inner Solar System fluids-fluid inclusions in meteorites. Meteoritic aqueous fluid inclusions are not rare, but they are very tiny and their characterization is at the state of the art for most analytical techniques. Meteoritic fluid inclusions offer us a unique opportunity to study early Solar System brines in the laboratory. Inclusion-by-inclusion analyses of the trapped fluids in carefully selected samples will, in the immediate future, provide us detailed information on the evolution of fluids as they interacted with anhydrous solid materials. Thus, real data can replace calculated fluid compositions in thermochemical calculations of the evolution of water and aqueous reactions in comets, asteroids, moons and the terrestrial planets.This article is part of the themed issue 'The origin, history and role of water in the evolution of the inner Solar System'. © 2017 The Author(s).

  16. New results on Late Quaternary stratigraphy of Manych depression

    Science.gov (United States)

    Kurbanov, Redzhep; Yanina, Tamara; Borisova, Olga

    2017-04-01

    Manych-strait connected Black sea and Caspian Sea in Pleistocene is a great event in the history of the Ponto-Caspian region. The strait located within such geological structure as Manych Depression which is extended sublatitudinally from the west coast of Nothern Caspian to the north-west of the Azov sea. The existence of the Manych-strait is essentially for the stratigraphy and paleogeography. There were several stages when marine waters spilled over from Black sea to Caspian and alternatively. Due to the alternation of sedimentary layers it is possible to correlate pleistocene deposits and paleogeographic events. Nowadays there are a lot of materials and data about the history of Manych-strait. In the profile are distinguished interbedding marine deposits with lacustrine and alluvial formations and subaerial deposit on top. The main question is the paleogeographical reconstruction. We try to solve this problem using our new data and elaborating available information. In February 2016 complex geomorphologic and paleogeographic works in central part of depression on northern coast of Manych-Gudilo lake were carried out. We performed cable drilling of 2 cores (depth of each 45 m) and hand hammer drilling (8 boreholes, max. depth 12 m) of covering Holocene sediments on different geomorphological levels of depression. From the core (3 cm diameter) continuous sampling was made for spore-pollen, lithological and geochemical analyzes. The stratigraphic subdivision of the core is based on facial-lithology and macro-malakofaunistic analisys. In the lower part of both cores there is barren formation of interbedding layers of sand and clays. The bottom line is precise, below lays a marine Carangat formation (MIS-5) of sand and clay with well-preserved Black Sea marine mollusk shells (Cardium edule, Paphia senescens, Ostrea edulis, Loripes lacteus, Chione gallina, Chlamys glabra). Higher in the core there is a loam-clay layer including both Black Sea (euryhaline species

  17. Inclusive differentiated instruction

    Directory of Open Access Journals (Sweden)

    Jerković Ljiljana S.

    2017-01-01

    Full Text Available Inclusive differentiated instruction is a new model of didactic instruction, theoretically described and established in this paper for the first time, after being experimentally verified through teaching of the mother tongue (instruction in reading and literature. Inclusive individually planned instruction is based on a phenomenological and constructivist didactic instructional paradigm. This type of teaching is essentially developmental and person-oriented. The key stages of inclusive differentiated instruction of literature are: 1 recognition of individual students' potential and educational needs regarding reading and work on literary texts; 2 planning and preparation of inclusive individually planned instruction in reading and literature; 3 actual class teaching of lessons thus prepared; and 4 evaluation of the student achievement following inclusive differentiated instruction in reading and literature. A highly important element of the planning and preparation of inclusive differentiated instruction is the creation of student profiles and inclusive individualized syllabi. Individualized syllabi specify the following: 1. a brief student profile; 2. the student position on the continuum of the learning outcomes of instruction in the Serbian language; 3. reverse-engineered macro-plan stages of instruction in the Serbian language (3.1. identifying expected outcomes and fundamental qualities of learners' work, 3.2. defining acceptable proofs of their realisation, 3.3. planning learning and teaching experiences, and 3.4. providing material and technical requisites for teaching; 4 the contents and procedure of individualized lessons targeting the student; 5 a plan of syllabus implementation monitoring and evaluation. The continuum of the learning outcomes of inclusive differentiated instruction in literature exists at three main levels, A, B and C. The three levels are: A reading techniques and learning about the main literary theory concepts; B

  18. Multilingualism and Social Inclusion

    DEFF Research Database (Denmark)

    2017-01-01

    This is a thematic issue on the relation between multilingualism and social inclusion. Due to globalization, Europeanization, supranational and transnational regulations linguistic diversity and multilingualism are on the rise. Migration and old and new forms of mobility play an important role...... into practice. This lead to forced linguistic assimilation and the elimination of cultural and linguistic heritage. Now, in the present age of globalization, linguistic diversity at the national state level has been recognized and multilingual states have been developing where all types of languages can be used...... in governance and daily life protected by a legal framework. This does not mean that there is full equality of languages. This carries over to the fair and just social inclusion of the speakers of these weaker, dominated languages as well. There is always a power question related to multilingualism. The ten...

  19. Chicxulub Post-Impact Sedimentary Sequence: Integrated Borehole Paleogene Carbonate Stratigraphy

    Science.gov (United States)

    Fucugauchi, J. U.; Perez-Cruz, L. L.; Escobar-Sanchez, E.; Ortega-Nieto, A.; Velasco-Villarreal, M.

    2014-12-01

    The Chicxulub crater was formed by a bolide impact on the southern Gulf of Mexico at ~66 Ma ago that marked the Cretaceous/Paleogene (K/Pg) boundary, represented worldwide by the ejecta layer. The K/Pg boundary layer with its global distribution provides a high resolution marker, allowing high precision stratigraphic analyses in marine and continental sequences. Following crater formation, sedimentation re-established in the carbonate platform, filling the basin. Crater is located half on-land and half offshore, with the crater floor covered by sediments with variable thickness up to about 1 km. The target, impact and post-impact sequences have been drilled and cored, providing samples for stratigraphic, petrographic and physical-chemical laboratory studies. The post-impact stratigraphy has been analyzed in several studies at proximal, intermediate and distal outcrops and in the crater boreholes, using e.g., radiometric dating, micropaleontology, paleomagnetism, and strontium and stable isotope geochemistry. Emphasis has been given on the impact breccias-carbonates contact and the basal Paleocene sequence. Here we re-analyze the available data, revisiting the stratigraphy for the Santa Elena, Tekax, Peto and Yaxcopoil-1 boreholes using newly constructed detailed lithostratigraphic columns in the continuously cored boreholes. Additionally we extend the study to the Paleogene sequence in the Santa Elena and Yaxcopoil-1 boreholes using bulk carbon and oxygen isotopes, magnetic polarity, XRF core geochemistry and magnetic susceptibility stratigraphy. Results spanning chrons c29 to c24 constrain the K/Pg boundary, c29r-c29n polarity reversal and the Paleocene-Eocene thermal maximum, providing high resolution records. The basal Paleocene gap and age differences in an integrated stratigraphy are discussed and correlated to the GPTS scale and IODP marine isotope records. The extent and characteristics of crater structure and target/cover sediments have been imaged with

  20. INTEGRATION-INCLUSION

    OpenAIRE

    KERAMITCHIEVSKA-BILJANOVSKA Vesna; MITREVSKA Roberta; SABOLICH Nada

    2015-01-01

    By defining the terms, we would like to show that mentally disabled children cannot follow the regular educational process, in the same way children without learning disabilities can.The process of rehabilitation and education of disabled persons with different kind of disabilities, enables independent social integration and good quality of living in our country in the last 50 years; throw there is no need of changes in the inclusive education.

  1. The Upper Cenomanian and Lower Turonian of Lockwitz (Dresden area, Saxony, Germany): lithofacies, stratigraphy and fauna of a transgressive succesion

    Czech Academy of Sciences Publication Activity Database

    Wilmsen, M.; Vodrážka, Radek; Niebuhr, B.

    2011-01-01

    Roč. 540, - (2011), s. 27-45 ISSN 0071-9404 Institutional research plan: CEZ:AV0Z30130516 Keywords : Upper Cretaceous * Klippenfazies * integrates stratigraphy * facies development * sea-level change Subject RIV: DB - Geology ; Mineralogy

  2. Geological Interpretation of the Structure and Stratigraphy of the A/M Area, Savannah River Site, South Carolina

    International Nuclear Information System (INIS)

    Wyatt, D.; Aadland, R.K.; Cumbest, R.J.; Stephenson, D.E.; Syms, F.H.

    1997-12-01

    The geological interpretation of the structure and stratigraphy of the A/M Area was undertaken in order to evaluate the effects of deeper Cretaceous aged geological strata and structure on shallower Tertiary horizons

  3. Inclusive Education in Italy: Description and Reflections on Full Inclusion

    Science.gov (United States)

    Anastasiou, Dimitris; Kauffman, James M.; Di Nuovo, Santo

    2015-01-01

    Inclusion of students with disabilities when appropriate is an important goal of special education for students with special needs. Full inclusion, meaning no education for any child in a separate setting, is held to be desirable by some, and Italy is likely the nation with an education system most closely approximating full inclusion on the…

  4. Core segment 15008 - Regolith stratigraphy at Apennine Front Station 2 using multispectral imaging

    Science.gov (United States)

    Pieters, C. M.; Meloy, A.; Hawke, B. R.; Nagle, J. S.

    1982-01-01

    High precision multispectral images for Apennine Front core segment 15008 are presented. These data have a spatial resolution less than approximately 0.5 mm and are analyzed for their compositional information using image analysis techniques. The stratigraphy of the regolith sampled by 15008 is documented here as three distinct zones, the most prominent of which is a feldspathic fragment-rich zone with a chaotic fabric that occurs between 10 and 18 cm depth. It is suggested that this material is the primary rim crest deposit of the local 10 m crater. Above this zone the stratigraphy is more horizontal in nature. Below this zone the soil is observed to be relatively homogeneous with no distinctive structure to 23 cm depth.

  5. Modeling of the Sedimentary Interbedded Basalt Stratigraphy for the Idaho National Laboratory Probabilistic Seismic Hazard Analysis

    Energy Technology Data Exchange (ETDEWEB)

    Suzette Payne

    2006-04-01

    This report summarizes how the effects of the sedimentary interbedded basalt stratigraphy were modeled in the probabilistic seismic hazard analysis (PSHA) of the Idaho National Laboratory (INL). Drill holes indicate the bedrock beneath INL facilities is composed of about 1.1 km of alternating layers of basalt rock and loosely consolidated sediments. Alternating layers of hard rock and “soft” loose sediments tend to attenuate seismic energy greater than uniform rock due to scattering and damping. The INL PSHA incorporated the effects of the sedimentary interbedded basalt stratigraphy by developing site-specific shear (S) wave velocity profiles. The profiles were used in the PSHA to model the near-surface site response by developing site-specific stochastic attenuation relationships.

  6. Modeling of the Sedimentary Interbedded Basalt Stratigraphy for the Idaho National Laboratory Probabilistic Seismic Hazard Analysis

    Energy Technology Data Exchange (ETDEWEB)

    Suzette Payne

    2007-08-01

    This report summarizes how the effects of the sedimentary interbedded basalt stratigraphy were modeled in the probabilistic seismic hazard analysis (PSHA) of the Idaho National Laboratory (INL). Drill holes indicate the bedrock beneath INL facilities is composed of about 1.1 km of alternating layers of basalt rock and loosely consolidated sediments. Alternating layers of hard rock and “soft” loose sediments tend to attenuate seismic energy greater than uniform rock due to scattering and damping. The INL PSHA incorporated the effects of the sedimentary interbedded basalt stratigraphy by developing site-specific shear (S) wave velocity profiles. The profiles were used in the PSHA to model the near-surface site response by developing site-specific stochastic attenuation relationships.

  7. Inclusion-Body Myositis: Diagnosis

    Science.gov (United States)

    ... for MDA Blog Donate Search MDA.org Close Inclusion-Body Myositis (IBM) Share print email share facebook ... As with other muscle diseases, a doctor diagnoses inclusion-body myositis (IBM) by considering the individual’s personal ...

  8. Fluid Shifts

    Science.gov (United States)

    Stenger, M. B.; Hargens, A. R.; Dulchavsky, S. A.; Arbeille, P.; Danielson, R. W.; Ebert, D. J.; Garcia, K. M.; Johnston, S. L.; Laurie, S. S.; Lee, S. M. C.; hide

    2017-01-01

    Introduction. NASA's Human Research Program is focused on addressing health risks associated with long-duration missions on the International Space Station (ISS) and future exploration-class missions beyond low Earth orbit. Visual acuity changes observed after short-duration missions were largely transient, but now more than 50 percent of ISS astronauts have experienced more profound, chronic changes with objective structural findings such as optic disc edema, globe flattening and choroidal folds. These structural and functional changes are referred to as the visual impairment and intracranial pressure (VIIP) syndrome. Development of VIIP symptoms may be related to elevated intracranial pressure (ICP) secondary to spaceflight-induced cephalad fluid shifts, but this hypothesis has not been tested. The purpose of this study is to characterize fluid distribution and compartmentalization associated with long-duration spaceflight and to determine if a relation exists with vision changes and other elements of the VIIP syndrome. We also seek to determine whether the magnitude of fluid shifts during spaceflight, as well as any VIIP-related effects of those shifts, are predicted by the crewmember's pre-flight status and responses to acute hemodynamic manipulations, specifically posture changes and lower body negative pressure. Methods. We will examine a variety of physiologic variables in 10 long-duration ISS crewmembers using the test conditions and timeline presented in the figure below. Measures include: (1) fluid compartmentalization (total body water by D2O, extracellular fluid by NaBr, intracellular fluid by calculation, plasma volume by CO rebreathe, interstitial fluid by calculation); (2) forehead/eyelids, tibia, and calcaneus tissue thickness (by ultrasound); (3) vascular dimensions by ultrasound (jugular veins, cerebral and carotid arteries, vertebral arteries and veins, portal vein); (4) vascular dynamics by MRI (head/neck blood flow, cerebrospinal fluid

  9. Seismic stratigraphy and sedimentary architecture of the Chalk Group in south-west Denmark

    DEFF Research Database (Denmark)

    Larsen, Connie; Ineson, Jon; Boldreel, Lars Ole

    2014-01-01

    The article focuses on a study undertaken by the Chalk Group on the western onshore region of the Danish Basin in Eastern Denmark related on the seismic stratigraphy and sedimentary architecture of the region. The study is undertaken through subdividing the northern North German Basin and the sou......-western Danish Basin on digital reflection using 2-dimensional digital and scanned seismic profiling. The results of the study sh regional trends related to the active indicate active inversion....

  10. Dynamic characteristics of cylindrical shells considering Fluid-structure interaction

    International Nuclear Information System (INIS)

    Jhung, Myung Jo; Kim, Wal Tae; Ryu, Yong Ho

    2009-01-01

    To assure the reliability of cylinders or shells with fluid-filled annulus, it is necessary to investigate the modal characteristics considering fluid-structure interaction effect. In this study, theoretical background and several finite element models are developed for cylindrical shells with fluid-filled annulus considering fluid-structure interaction. The effect of the inclusion of the fluid-filled annulus on the natural frequencies is investigated, which frequencies are used for typical dynamic analyses such as responses spectrum, power spectral density and unit load excitation. Their response characteristics are addressed with respect to the various representations of the fluid-structure interaction effect

  11. Supporting Teachers in Inclusive Education

    Directory of Open Access Journals (Sweden)

    Alekhina S.V.

    2015-03-01

    Full Text Available The article regards the issues of support provision to teachers involved in inclusive education as the main requirement for successful realization of inclusion. The methodological framework used in the study is a resource approach. The article describes the ways of extending the means of supporting teachers. The article also arguments for consolidating all the educators of inclusive schools into inclusive teams equally interested in joint work of administration and educators of intervention programs.

  12. Singing and social inclusion.

    Science.gov (United States)

    Welch, Graham F; Himonides, Evangelos; Saunders, Jo; Papageorgi, Ioulia; Sarazin, Marc

    2014-01-01

    There is a growing body of neurological, cognitive, and social psychological research to suggest the possibility of positive transfer effects from structured musical engagement. In particular, there is evidence to suggest that engagement in musical activities may impact on social inclusion (sense of self and of being socially integrated). Tackling social exclusion and promoting social inclusion are common concerns internationally, such as in the UK and the EC, and there are many diverse Government ministries and agencies globally that see the arts in general and music in particular as a key means by which social needs can be addressed. As part of a wider evaluation of a national, Government-sponsored music education initiative for Primary-aged children in England ("Sing Up"), opportunity was taken by the authors, at the request of the funders, to assess any possible relationship between (a) children's developing singing behavior and development and (b) their social inclusion (sense of self and of being socially integrated). Subsequently, it was possible to match data from n = 6087 participants, drawn from the final 3 years of data collection (2008-2011), in terms of each child's individually assessed singing ability (based on their singing behavior of two well-known songs to create a "normalized singing score") and their written responses to a specially-designed questionnaire that included a set of statements related to children's sense of being socially included to which the children indicated their level of agreement on a seven-point Likert scale. Data analyses suggested that the higher the normalized singing development rating, the more positive the child's self-concept and sense of being socially included, irrespective of singer age, sex and ethnicity.

  13. Singing and social inclusion

    Science.gov (United States)

    Welch, Graham F.; Himonides, Evangelos; Saunders, Jo; Papageorgi, Ioulia; Sarazin, Marc

    2014-01-01

    There is a growing body of neurological, cognitive, and social psychological research to suggest the possibility of positive transfer effects from structured musical engagement. In particular, there is evidence to suggest that engagement in musical activities may impact on social inclusion (sense of self and of being socially integrated). Tackling social exclusion and promoting social inclusion are common concerns internationally, such as in the UK and the EC, and there are many diverse Government ministries and agencies globally that see the arts in general and music in particular as a key means by which social needs can be addressed. As part of a wider evaluation of a national, Government-sponsored music education initiative for Primary-aged children in England (“Sing Up”), opportunity was taken by the authors, at the request of the funders, to assess any possible relationship between (a) children's developing singing behavior and development and (b) their social inclusion (sense of self and of being socially integrated). Subsequently, it was possible to match data from n = 6087 participants, drawn from the final 3 years of data collection (2008–2011), in terms of each child's individually assessed singing ability (based on their singing behavior of two well-known songs to create a “normalized singing score”) and their written responses to a specially-designed questionnaire that included a set of statements related to children's sense of being socially included to which the children indicated their level of agreement on a seven-point Likert scale. Data analyses suggested that the higher the normalized singing development rating, the more positive the child's self-concept and sense of being socially included, irrespective of singer age, sex and ethnicity. PMID:25120514

  14. Singing and social inclusion

    Directory of Open Access Journals (Sweden)

    Graham Frederick Welch

    2014-07-01

    Full Text Available There is a growing body of neurological, cognitive and social psychological research to suggest the possibility of positive transfer effects from structured musical engagement. In particular, there is evidence to suggest that engagement in musical activities may impact on social inclusion (sense of self and of being socially integrated. Tackling social exclusion and promoting social inclusion are common concerns internationally, such as in the UK and the EC, and there are many diverse Government ministries and agencies globally that see the arts in general and music in particular as a key means by which social needs can be addressed. As part of a wider evaluation of a national, Government-sponsored music education initiative for Primary-aged children in England (‘Sing Up’, opportunity was taken by the authors, at the request of the funders, to assess any possible relationship between (a children’s developing singing behaviour and development and (b their social inclusion (sense of self and of being socially integrated. Subsequently, it was possible to match data from n=6087 participants, drawn from the final three years of data collection (2008-2011, in terms of each child’s individually assessed singing ability (based on their singing behaviour of two well-known songs to create a 'normalised singing score' and their written responses to a specially-designed questionnaire that included a set of statements related to children’s sense of being socially included to which the children indicated their level of agreement on a seven-point Likert scale. Data analyses suggested that the higher the normalized singing development rating, the more positive the child’s self-concept and sense of being socially included, irrespective of singer age, sex and ethnicity.

  15. Application of sequence stratigraphy to carbonate reservoir prediction, Early Palaeozoic eastern Warburton basin, South Australia

    Energy Technology Data Exchange (ETDEWEB)

    Xiaowen S.; Stuart, W.J.

    1996-12-31

    The Early Palaeozoic Warburton Basin underlies the gas and oil producing Cooper and Eromanga Basins. Postdepositional tectonism created high potential fracture porosities, complicating the stratigraphy and making reservoir prediction difficult. Sequence stratigraphy integrating core, cuttings, well-log, seismic and biostratigraphic data has recognized a carbonate-dominated to mixed carbonate/siliciclastic supersequence comprising several depositional sequences. Biostratigraphy based on trilobites and conodonts ensures reliable well and seismic correlations across structurally complex areas. Lithofacies interpretation indicates sedimentary environments ranging from carbonate inner shelf, peritidal, shelf edge, deep outer shelf and slope to basin. Log facies show gradually upward shallowing trends or abrupt changes indicating possible sequence boundaries. With essential depositional models and sequence analysis from well data, seismic facies suggest general reflection configurations including parallel-continuous layered patterns indicating uniform neuritic shelf, and mounded structures suggesting carbonate build-ups and pre-existing volcanic relief. Seismic stratigraphy also reveals inclined slope and onlapping margins of a possibly isolated platform geometry. The potential reservoirs are dolomitized carbonates containing oomoldic, vuggy, intercrystalline and fracture porosities in lowstand systems tracts either on carbonate mounds and shelf crests or below shelf edge. The source rock is a deep basinal argillaceous mudstone, and the seal is fine-grained siltstone/shale of the transgressive system tract.

  16. Application of sequence stratigraphy to carbonate reservoir prediction, Early Palaeozoic eastern Warburton basin, South Australia

    Energy Technology Data Exchange (ETDEWEB)

    Xiaowen S.; Stuart, W.J.

    1996-01-01

    The Early Palaeozoic Warburton Basin underlies the gas and oil producing Cooper and Eromanga Basins. Postdepositional tectonism created high potential fracture porosities, complicating the stratigraphy and making reservoir prediction difficult. Sequence stratigraphy integrating core, cuttings, well-log, seismic and biostratigraphic data has recognized a carbonate-dominated to mixed carbonate/siliciclastic supersequence comprising several depositional sequences. Biostratigraphy based on trilobites and conodonts ensures reliable well and seismic correlations across structurally complex areas. Lithofacies interpretation indicates sedimentary environments ranging from carbonate inner shelf, peritidal, shelf edge, deep outer shelf and slope to basin. Log facies show gradually upward shallowing trends or abrupt changes indicating possible sequence boundaries. With essential depositional models and sequence analysis from well data, seismic facies suggest general reflection configurations including parallel-continuous layered patterns indicating uniform neuritic shelf, and mounded structures suggesting carbonate build-ups and pre-existing volcanic relief. Seismic stratigraphy also reveals inclined slope and onlapping margins of a possibly isolated platform geometry. The potential reservoirs are dolomitized carbonates containing oomoldic, vuggy, intercrystalline and fracture porosities in lowstand systems tracts either on carbonate mounds and shelf crests or below shelf edge. The source rock is a deep basinal argillaceous mudstone, and the seal is fine-grained siltstone/shale of the transgressive system tract.

  17. Upper Neogene stratigraphy and tectonics of Death Valley — a review

    Science.gov (United States)

    Knott, J. R.; Sarna-Wojcicki, A. M.; Machette, M. N.; Klinger, R. E.

    2005-12-01

    New tephrochronologic, soil-stratigraphic and radiometric-dating studies over the last 10 years have generated a robust numerical stratigraphy for Upper Neogene sedimentary deposits throughout Death Valley. Critical to this improved stratigraphy are correlated or radiometrically-dated tephra beds and tuffs that range in age from > 3.58 Ma to Mormon Point. This new geochronology also establishes maximum and minimum ages for Quaternary alluvial fans and Lake Manly deposits. Facies associated with the tephra beds show that ˜3.3 Ma the Furnace Creek basin was a northwest-southeast-trending lake flanked by alluvial fans. This paleolake extended from the Furnace Creek to Ubehebe. Based on the new stratigraphy, the Death Valley fault system can be divided into four main fault zones: the dextral, Quaternary-age Northern Death Valley fault zone; the dextral, pre-Quaternary Furnace Creek fault zone; the oblique-normal Black Mountains fault zone; and the dextral Southern Death Valley fault zone. Post - 3.3 Ma geometric, structural, and kinematic changes in the Black Mountains and Towne Pass fault zones led to the break up of Furnace Creek basin and uplift of the Copper Canyon and Nova basins. Internal kinematics of northern Death Valley are interpreted as either rotation of blocks or normal slip along the northeast-southwest-trending Towne Pass and Tin Mountain fault zones within the Eastern California shear zone.

  18. 3D mechanical stratigraphy of a deformed multi-layer: Linking sedimentary architecture and strain partitioning

    Science.gov (United States)

    Cawood, Adam J.; Bond, Clare E.

    2018-01-01

    Stratigraphic influence on structural style and strain distribution in deformed sedimentary sequences is well established, in models of 2D mechanical stratigraphy. In this study we attempt to refine existing models of stratigraphic-structure interaction by examining outcrop scale 3D variations in sedimentary architecture and the effects on subsequent deformation. At Monkstone Point, Pembrokeshire, SW Wales, digital mapping and virtual scanline data from a high resolution virtual outcrop have been combined with field observations, sedimentary logs and thin section analysis. Results show that significant variation in strain partitioning is controlled by changes, at a scale of tens of metres, in sedimentary architecture within Upper Carboniferous fluvio-deltaic deposits. Coupled vs uncoupled deformation of the sequence is defined by the composition and lateral continuity of mechanical units and unit interfaces. Where the sedimentary sequence is characterized by gradational changes in composition and grain size, we find that deformation structures are best characterized by patterns of distributed strain. In contrast, distinct compositional changes vertically and in laterally equivalent deposits results in highly partitioned deformation and strain. The mechanical stratigraphy of the study area is inherently 3D in nature, due to lateral and vertical compositional variability. Consideration should be given to 3D variations in mechanical stratigraphy, such as those outlined here, when predicting subsurface deformation in multi-layers.

  19. The El Masnou infralittoral sedimentary environment (Barcelona province, NW Mediterranean Sea: morphology and Holocene seismic stratigraphy

    Directory of Open Access Journals (Sweden)

    Gemma Ercilla

    2010-03-01

    Full Text Available A detailed analysis of the morphology and the Holocene seismic and sequence stratigraphy and architecture of the infralittoral sedimentary environment of the El Masnou coast (Catalonia, NW Mediterranean Sea was carried out using multibeam bathymetry and GeoPulse seismic data. This environment extends down to 26-30 m water depth, and is defined morphologically by two depositional wedges whose seafloor is affected by erosive furrows, slides, fields of large- and small-scale wavy bedforms, and dredging trenches and pits. Erosive terraces are also identified in the transition domain toward the inner continental shelf. The Holocene stratigraphy of the infralittoral environment is defined by two major seismic sequences (lower and upper, each one formed by internal seismic units. The sequences and units are characterised by downlapping surfaces made up of deposits formed by progradation of coastal lithosomes. The stratigraphy and stratal architecture, displaying a retrogradational arrangement with progradational patterns of minor order, were controlled by different sea-level positions. The stratigraphic division represents the coastal response to the last fourth-order transgressive and highstand conditions, modulated by small-scale sea-level oscillations (≈1-2 m of fith to sixth order. This study also highlights the advantage of an integrated analysis using acoustic/seismic methods for practical assessment of the anthropogenic effects on infralittoral domains based on the association of marine geological observations.

  20. Designing Inclusive Spaces

    DEFF Research Database (Denmark)

    Colfelt, Solvej

    2012-01-01

    CWUAAT -6.TH CAMBRIDGE WORKSHOP – 2012 Designing inclusive systems for real-world applications Abstracht: Denmark has planned huge investments in development in healthcare systems. Nearly 50 billion danish krones has been set aside on the stately budget for this purpose to be spent over the next 10...... hospital complexes ? The article will explore the fundament of wayshowing on the basis of prior research as well as on the basis of the results of a case study in a large existing danish hospital complex. The result points to signage being an inevitable factor but also that it is a factor that is not very...

  1. Study of Meteoritic Inclusion

    DEFF Research Database (Denmark)

    Olsen, Mia Bjørg Stolberg

    . The manuscripts presented in this thesis have provided critical insights into the origin and distribution of short-lived radioisotopes as well as the formation and transport history of chondrules and, by extension, the precursor material to asteroidal and planetary bodies. The proposal of 26Al heterogeneity...... and the observation of a reduced initial abundance of 26Al in the accretion regions of chondrules and asteroidal bodies impacts our understanding of the accretion timescales of protoplanets in a significant way. Combining high-precision isotope measurements of multiple systems on individual meteoritic inclusions...

  2. Inclusive Education under Collectivistic Culture

    Science.gov (United States)

    Futaba, Yasuko

    2016-01-01

    This paper addresses how inclusive education under collective culture is possible. Inclusive education, which more-or-less involves changing the current schools, has been denied, doubted or distorted by both policy-makers and practitioners of general and special education in Japan. Main reason for the setback in inclusive education can be…

  3. Inclusive Education in South Korea

    Science.gov (United States)

    Kim, Yong-Wook

    2014-01-01

    The purpose of this paper is to examine the current implementation of inclusive education in South Korea and discuss its challenges. The history of special education is first described followed by an introduction to policies relevant to special and inclusive education. Next, a critical discussion of the state of inclusive education follows built…

  4. Stratigraphy of the PB-1 well, Nopal I uranium deposit, Sierra Pena Blanca, Chihuahua, Mexico

    Energy Technology Data Exchange (ETDEWEB)

    Dobson, P.; Fayek, M.; Goodell, P.; Ghezzehei, T.; Melchor, F.; Murrell, M.; Oliver, R.; Reyes-Cortes, I.A.; de la Garza, R.; Simmons, A.

    2008-08-01

    The Nopal I site in the Pena Blanca uranium district has a number of geologic and hydrologic similarities to the proposed high-level radioactive waste repository at Yucca Mountain, making it a useful analogue to evaluate process models for radionuclide transport. The PB-1 well was drilled in 2003 at the Nopal I uranium deposit as part of a DOE-sponsored natural analogue study to constrain processes affecting radionuclide transport. The well penetrates through the Tertiary volcanic section down to Cretaceous limestone and intersects the regional aquifer system. The well, drilled along the margin of the Nopal I ore body, was continuously cored to a depth of 250 m, thus providing an opportunity to document the local stratigraphy. Detailed observations of these units were afforded through petrographic description and rock-property measurements of the core, together with geophysical logs of the well. The uppermost unit encountered in the PB-1 well is the Nopal Formation, a densely welded, crystal-rich, rhyolitic ash-flow tuff. This cored section is highly altered and devitrified, with kaolinite, quartz, chlorite, and montmorillonite replacing feldspars and much of the groundmass. Breccia zones within the tuff contain fracture fillings of hematite, limonite, goethite, jarosite, and opal. A zone of intense clay alteration encountered in the depth interval 17.45-22.30 m was interpreted to represent the basal vitrophyre of this unit. Underlying the Nopal Formation is the Coloradas Formation, which consists of a welded lithic-rich rhyolitic ash-flow tuff. The cored section of this unit has undergone devitrification and oxidation, and has a similar alteration mineralogy to that observed in the Nopal tuff. A sharp contact between the Coloradas tuff and the underlying Pozos Formation was observed at a depth of 136.38 m. The Pozos Formation consists of poorly sorted conglomerate containing clasts of subangular to subrounded fragments of volcanic rocks, limestone, and chert

  5. Financial inclusion: Policies and practices

    Directory of Open Access Journals (Sweden)

    Thankom Arun

    2015-12-01

    Full Text Available As a key enabler for development, financial inclusion is firmly placed on the agenda of most governments as a key policy priority. Against this background, this round table provides a global and regional perspective on the policies and practices of financial inclusion. Using macro data, the collection reveals the diversity in the efforts towards achieving financial inclusion and the need for a progressive approach in financial inclusion. Further to this, the round table provides the regional perspectives on the policies and practices of financial inclusion in India, South Africa, and Australia.

  6. Seismic stratigraphy and structure of the Chukchi Borderland: implications for the opening of the Canada Basin

    Science.gov (United States)

    Ilhan, I.; Coakley, B.

    2015-12-01

    Interpretation of seismic reflection data from the western Chukchi Borderland has illuminated the structure and stratigraphy of the area. Basement rotated fault blocks are offset by two border fault systems (BFS1 and BFS2) and by secondary faults, striking curvilinear in the NW-SE direction, dipping to the NE. The BFS1 dissects the Chukchi Plateau into two first-order rotated blocks bounding two major sedimentary depocentres, the North Chukchi Basin and the Chukchi Plateau Central Basin. The BFS2, which has a larger offset than BFS1, forms the western boundary of the Northwind Basin. Much of the stratigraphy is controlled by sediment supply. The basins were starved early in their history, resulting in a limited syn-rift section. Substantial sediment accumulation in the Borderland appears to post-date large scale progradation of the depostional shelf edge across the Chukchi Shelf. Basin infill stratigraphies are subdivided into pre-rift, syn-rift, early-, middle-, late post-rift, and glacio-marine sequences (SB1-SB5). SB1 shows truncation of the remnants of the pre-rift strata below and onlap of the syn-rift sequence(s) above; the SB2 marks the termination of the rifting stage and is bounded by bi-directional onlap surface of the early post-rift strata above; the base of SB3 is an onlap surface marks the arrival of the prograding shelf margin sequence(s); the SB4 shows evidence of erosion at the base of the prograding late post-rift sequence(s); and the SB5 is an downloap surface marking the first arrival of the glacio-marine sediments eroded from the Chukchi Shelf. Two ages of the major sequence boundaries, the SB3 and SB4, can be directly tied to Popcorn and Crackerjack Chukchi Shelf well data, and the older ones, the end of rifting and the top of the pre-rift, are inferred based on stratigraphic observations. The stratigraphic relationship suggests that the Chukchi Borderland stratigraphy can be correlated in part to the Chukchi Shelf stratigraphy. The first and

  7. Fluid Mechanics

    Science.gov (United States)

    Pnueli, David; Gutfinger, Chaim

    1997-01-01

    This text is intended for the study of fluid mechanics at an intermediate level. The presentation starts with basic concepts, in order to form a sound conceptual structure that can support engineering applications and encourage further learning. The presentation is exact, incorporating both the mathematics involved and the physics needed to understand the various phenomena in fluid mechanics. Where a didactical choice must be made between the two, the physics prevails. Throughout the book the authors have tried to reach a balance between exact presentation, intuitive grasp of new ideas, and creative applications of concepts. This approach is reflected in the examples presented in the text and in the exercises given at the end of each chapter. Subjects treated are hydrostatics, viscous flow, similitude and order of magnitude, creeping flow, potential flow, boundary layer flow, turbulent flow, compressible flow, and non-Newtonian flows. This book is ideal for advanced undergraduate students in mechanical, chemical, aerospace, and civil engineering. Solutions manual available.

  8. Inclusive Physical Education

    DEFF Research Database (Denmark)

    Østergaard, Charlotte; Rostbøll, Solveig Fogh

    2015-01-01

    EN317 - Inclusive Physical Education - with a focus on active and successful participation Charlotte Østergaard, Solveig Fogh Rostbøll, Department of School and Learning, Metropolitan University College (DK) chao@phmetropol.dk The Danish School Reform 2014 intends to raise the amount and intensity...... and ability to participate in PE must be understood in specific socio-cultural and socio-economic conditions. The hypothesis of the study is that the experience of being acknowledged for your efforts in physical education by significant others can form the basis for the construction of physical capital. EN323...... - Iranian Female Adolescent Immigrants’ Experiences of the Canadian Physical Education System Bahar Tajrobehkar, University of Toronto (CA) btajro@gmail.co...

  9. Can we build inclusion?

    DEFF Research Database (Denmark)

    Kirkeby, Inge Mette; Grangaard, Sidse

    2016-01-01

    of some children with special needs. Hence the title – can we build inclusion? In the literature of Universal Design, accommodation and design features seldom reflect the less visible disabilities. The paper is based on a research project initiated to investigate how more or less space influences daily......, the amount of space is crucial. This group consisted of children who were socially very extrovert, and who maybe were noisy, easily provoked, and quick to get involved in arguments with other children. Alternatively, children in the group were very restrained and withdrawn in social interaction. Based...... and furnishing of the kindergarten is an advantage for all children. This is a clear example of Universal Design in which architectural solutions that are good for one specific group are also beneficial for all children...

  10. Between psychopathology and inclusion

    DEFF Research Database (Denmark)

    Hamre, Bjørn Frithiof; Hedegaard-Sørensen, Lotte; Langager, Søren

    2017-01-01

    and social pedagogy. We thus enquire into how the rise of diagnostics and medicalisation affects our understanding of children’s difficulties. We discuss a paradox that is present in Denmark and other countries. As educational policies emphasise inclusion, the field of schooling experiences a huge rise......This article reports on a Danish study on interprofessional collaboration between child psychiatrists and educational psychologists concerning children who are categorised as being at risk. Methodologically, the analysis is grounded in qualitative interviews with psychologists. A Foucauldian...... approach is applied to narratives and experiences that occur within these interviews concerning external collaboration with child psychiatrists. The article is informed by the research tradition that has problematised the significance of psychiatry and diagnoses in the field of special needs education...

  11. IPads in Inclusive Classrooms

    DEFF Research Database (Denmark)

    Meyer, Bente Tobiesen

    2015-01-01

    This paper builds on data from a research project where iPads were used in a lower secondary school in Denmark to support school development and inclusive learning environments. The paper explores how iPads enter into and work as part of an ecology of learning resources in five classes in lower...... secondary school. I conceptualize the systems of related technologies observed in this school as ecologies of learning resources as they present themselves as carefully balanced systems in which educational resources circulate in different ways that make sense for learners’ needs. Inspired by Actor...... in by pupils the paper argues that we should disengage approaches to the iPad in education from ideas of what the properties of these technologies are, and see the device as a more relational and situated actor, avoiding the definition of properties of technologies outside the contexts specific to their use....

  12. Patterns of inclusion

    DEFF Research Database (Denmark)

    Pedersen, Alex Young; Nørgård, Rikke Toft; Köppe, Christian

    2018-01-01

    Reconsidering the concept of digital citizenship and the essential component of education the authors propose that the concept of Hybrid Education may serve both as a guideline for the utilization of digital technologies in education and as a methodology for fostering new forms of participation......, inclusion and engagement in society. Following T.H. Marshall’s conception of citizenship the authors suggest that becoming, belonging and the capabilities to do so is essential to digital citizenship in a culturally diverse and digitally mediated world. The paper presents a theory-based, value driven...... and practical orientated framework for innovation in education. The paper documents a process where participants situated around the globe worked in collaboration with a group of participants gathered at a workshop on the concept of hybridity in education and on identifying and describing educational patterns...

  13. Fluid dynamics

    CERN Document Server

    Ruban, Anatoly I

    This is the first book in a four-part series designed to give a comprehensive and coherent description of Fluid Dynamics, starting with chapters on classical theory suitable for an introductory undergraduate lecture course, and then progressing through more advanced material up to the level of modern research in the field. The present Part 1 consists of four chapters. Chapter 1 begins with a discussion of Continuum Hypothesis, which is followed by an introduction to macroscopic functions, the velocity vector, pressure, density, and enthalpy. We then analyse the forces acting inside a fluid, and deduce the Navier-Stokes equations for incompressible and compressible fluids in Cartesian and curvilinear coordinates. In Chapter 2 we study the properties of a number of flows that are presented by the so-called exact solutions of the Navier-Stokes equations, including the Couette flow between two parallel plates, Hagen-Poiseuille flow through a pipe, and Karman flow above an infinite rotating disk. Chapter 3 is d...

  14. Stratigraphy of the cambo-ordovician succession in Illnois

    Energy Technology Data Exchange (ETDEWEB)

    Lasemi, Yaghoob; Khorasgani, Zohreh; Leetaru, Hannes

    2014-09-30

    The Upper Cambrian through Lower Ordovician succession (Sauk II-III sequences) in the Illinois Basin covers the entire state of Illinois and most of the states of Indiana and Kentucky. To determine lateral and vertical lithologic variations of the rocks within the Cambro-Ordovician deposits that could serve as reservoir or seal for CO2 storage, detailed subsurface stratigraphic evaluation of the succession in Illinois was conducted. The Cambro-Ordovician succession in the Illinois Basin consists of mixed carbonate-siliciclastic deposits. Its thickness ranges from nearly 800 feet in the extreme northwest to nearly 8000 feet in the Reelfoot Rift in the extreme southeastern part of the state. In northern and central Illinois, the Cambro-Ordovician rocks are classified as the Cambrian Knox and the Ordovician Prairie du Chien Groups, which consist of alternating dolomite and siliciclastic units. In the southern and deeper part of the Illinois Basin, the Cambro-Ordovician deposits consist chiefly of fine to coarsely crystalline dolomite capped by the Middle Ordovician Everton Formation. Detailed facies analysis indicates that the carbonate units consist mainly of mudstone to grainstone facies (fossiliferous/oolitic limestone and dolomite) with relics of bioclasts, ooids, intraclasts and peloids recording deposition on a shallow marine ramp setting. The dominant lithology of the Knox and the overlying Prairie du Chien Group is fine to coarsely crystalline, dense dolomite. However, porous and permeable vugular or fractured/cavernous dolomite intervals that grade to dense fine to coarsely crystalline dolomite are present within the dolomite units. Several hundred barrels of fluid were lost in some of these porous intervals during drilling, indicating high permeability. The sandstone intervals are porous and permeable and are texturally and compositionally mature. The permeable sandstone and porous dolomite intervals are laterally extensive and could serve as important

  15. Inclusive Business - What It Is All About? Managing Inclusive Companies

    Directory of Open Access Journals (Sweden)

    Tea Golja

    2012-01-01

    Full Text Available Following the challenges we face today, the inclusive business models are future business models through which the Millennium Development Goals can be fostered and strengthen. These are the models which, through their strategic orientation on inclusivity, include low income communities in their value chain. This can be done through combining variety of strategies which all have two common points – recognition of stakeholders and adjustment of the product to the target market. The paper presents the analysis of inclusive markets. Hence, the research results show the dispersion of inclusive businesses worldwide, type of the organization, sector coverage, and contribution to MDGs as well as the particular way of inclusion of low income communities in their value chain. The aim is to present how inclusive business benefits not only the low income societies, but the companies that operate in this way as well.

  16. Inferring origin of mercury inclusions in quartz by multifractal analysis

    Science.gov (United States)

    Shibata, T.; Maruoka, T.; Echigo, T.

    2015-01-01

    In order to refine our understanding of how fluid inclusions were trapped in the host minerals, we non-destructively observed mercury inclusions (liquid Hg0) in quartz samples using X-ray computed tomography (CT) technique. The X-ray CT apparatus can observe internal structures of the samples and give cross-sectional images from the transmission of the X-rays through the samples. From the cross-sectional images, we obtained three-dimensional spatial distributions of mercury inclusions, and quantitatively analyzed them using fractal and multifractal methods. Although the samples were from different geological settings, the resultant fractal dimensions were 1.70 and 1.71 for the San Benito and Itomuka samples, respectively. The fractal dimensions were also close to those predicted by diffusion-limited aggregation models and percolation theory, which are controlled by the irreversible kinetics. Given the fractal dimension and its implied mechanism, we conclude that the mercury-bearing fluids were not primary fluid inclusions, but migrated into the pre-existing cracks of quartz crystals by diffusion processes.

  17. Inclusive spectra in hard processes

    International Nuclear Information System (INIS)

    Kiselev, A.V.; Petrov, V.A.

    1985-01-01

    It is shown that the unified mechanism of hadronization in hard processes results in universality of inclusive spectra of soft hadrons. Inclusive spectrum of hadrons in energy share in deep-inelastic lepton-hadron scattering is calculated. The spectrum obtained is calculated with analogous distribution in e + e - annihilation. It is noted that inclusive spectrum of soft hadrons in hard processes is described by a universal function

  18. Financial Stability and Financial Inclusion

    OpenAIRE

    Peter J. Morgan; Victor Pontines

    2014-01-01

    Developing economies are seeking to promote financial inclusion, i.e., greater access to financial services for low-income households and firms, as part of their overall strategies for economic and financial development. This raises the question of whether financial stability and financial inclusion are, broadly speaking, substitutes or complements. In other words, does the move toward greater financial inclusion tend to increase or decrease financial stability? A number of studies have sugge...

  19. Fluid mechanics

    International Nuclear Information System (INIS)

    Paraschivoiu, I.; Prud'homme, M.; Robillard, L.; Vasseur, P.

    2003-01-01

    This book constitutes at the same time theoretical and practical base relating to the phenomena associated with fluid mechanics. The concept of continuum is at the base of the approach developed in this work. The general advance proceeds of simple balances of forces as into hydrostatic to more complex situations or inertias, the internal stresses and the constraints of Reynolds are taken into account. This advance is not only theoretical but contains many applications in the form of solved problems, each chapter ending in a series of suggested problems. The major part of the applications relates to the incompressible flows

  20. Fluid Sounds

    DEFF Research Database (Denmark)

    and in architectural design. Aesthetics, psychoacoustics, perception, and cognition are all present in this expanding field embracing such categories as soundscape composition, sound art, sonic art, sound design, sound studies and auditory culture. Of greatest significance to the overall field is the investigation...... of sound, site and the social, and how the spatial, the visual, and the bodily interact in sonic environments, how they are constructed and how they are entangled in other practices. With the Seismograf special issue Fluid Sounds, we bring this knowledge into the dissemination of audio research itself...

  1. Principles of fluid mechanics

    International Nuclear Information System (INIS)

    Kreider, J.F.

    1985-01-01

    This book is an introduction on fluid mechanics incorporating computer applications. Topics covered are as follows: brief history; what is a fluid; two classes of fluids: liquids and gases; the continuum model of a fluid; methods of analyzing fluid flows; important characteristics of fluids; fundamentals and equations of motion; fluid statics; dimensional analysis and the similarity principle; laminar internal flows; ideal flow; external laminar and channel flows; turbulent flow; compressible flow; fluid flow measurements

  2. Accessibility and inclusion informational

    Directory of Open Access Journals (Sweden)

    Mônica Sena de Souza

    2013-06-01

    Full Text Available Introduction: Discusses the role of information professionals in meeting the informational demands of people with disabilities in the information society. The librarian is crucial for the effectiveness and success in the informational inclusion of people with disabilities, considering also continuing education for their professional qualification.Objective: To provide reflections on the role of the librarian in serving users with disabilities, highlighting the need for improvement in information units, identified in the scientific literature with regard to accessibility.Methodology: Literature search, based on a review of literature in books and scientific papers, highlighting the main authors: Adams (2000, Mazzoni (2001 and Sassaki (1997, 2002, 2005.Results: The lack of informational access for people with disabilities hampers their social and political participation, hence, reduces its condition of citizenship.Conclusion: The librarian responsible for seeking continuing education, greater involvement in the events of the area and the constant search for job training, which will reflect on the best service the information needs of users with disabilities.

  3. Inclusion by Design: Engineering Inclusive Practices in Secondary Schools

    Science.gov (United States)

    Dukes, Charles; Lamar-Dukes, Pamela

    2009-01-01

    In order to help teachers understand the importance of intentional design for inclusive education, this article describes the design process an engineer might use when designing a new project. If teachers learn to think like engineers, it is possible for them to design inclusive education. This conceptual design can then be combined with…

  4. Inclusions in Minerals: the Importance of Host Mineral Composition, Pressure and Temperature for Potential Inclusion Alteration

    Science.gov (United States)

    Marquardt, K.; Markl, G.

    2017-12-01

    Inclusions in minerals are used to decipher details of the host mineral/rock history. They frequently originate from the time of mineral formation; be it diamond, garnet or `common' feldspar. Thus protected they survive changing pressure and temperature for different durations compared to their non-enclosed counterparts. Inclusions may (partially) equilibrate at a later point in history, and thus provide complementary information on past processes and alteration pathways less commonly discussed. The study investigates partially altered pyroxene inclusions in feldspars indicative of high-p-T fluid transport during granulite facies metamorphism in charnockites from the Lofoten Islands in Northern Norway. The protoliths formed about 1750 Ma ago, at about 800 - 900°C and 4 kbar. During crustal thickening, they reached high-pressure granulite-facies conditions of about 8-11 kbar at 700°C (1). While this event caused large magmatic pyroxenes to react with an infiltrating fluid to form corona textures of amphibole; pyroxenes inside feldspars behaved very differently. Pyroxenes enclosed in orthoclase-rich feldspar were partially hydrated to amphiboles. Contrastingly, feldspar with lower orthoclase content protected the magmatic pyroxenes efficiently. Transport and transformation mechanisms recorded in these µm to nm textures were studied by EMPA and TEM. Focused Ion Beam (FIB) prepared TEM-foils revealed that pyroxenes, when spatially connected to albite exsolution lamellae, show dissolution features. Based on composition, nanostructures and the known p-T-history, we propose the following succession of events. Ternary feldspar containing small magmatic pyroxenes began to exsolve between about 800 and 700°C. The exsolution changed from coherent to incoherent and a fluid infiltrated the feldspar accompanied by a formation of nanotunnels. Gradually the tunnels grew larger so that finally whole film perthites acted as pathways. When the fluid had access to pyroxene

  5. Designing Inclusive Systems Designing Inclusion for Real-world Applications

    CERN Document Server

    Clarkson, John; Robinson, Peter; Lazar, Jonathan; Heylighen, Ann

    2012-01-01

    The Cambridge Workshops on Universal Access and Assistive Technology (CWUAAT) are a series of workshops held at a Cambridge University College every two years. The workshop theme: “Designing inclusion for real-world applications” refers to the emerging potential and relevance of the latest generations of inclusive design thinking, tools, techniques, and data, to mainstream project applications such as healthcare and the design of working environments. Inclusive Design Research involves developing tools and guidance enabling product designers to design for the widest possible population, for a given range of capabilities. There are five main themes: •Designing for the Real-World •Measuring Demand And Capabilities •Designing Cognitive Interaction with Emerging Technologies •Design for Inclusion •Designing Inclusive Architecture In the tradition of CWUAAT, we have solicited and accepted contributions over a wide range of topics, both within individual themes and also across the workshop’s scope. ...

  6. Numerical simulation of convection and inclusion distribution during solidification in a heavy steel ingot

    International Nuclear Information System (INIS)

    Lin, Rui; Shen, Houfa

    2015-01-01

    Inclusions content in the steel ingot is an important index for homogeneity, and it becomes more serious for heavy steel ingots which are used for major equipment. However, knowledge about the formation of inclusion in steel ingot is limited, and modeling of inclusion distribution is still challenging, so it is of great significance to research the behavior of inclusion. In this paper, fluid flow during solidification is numerically simulated based on the equilibrium equations of mass, momentum and energy, and then inclusion distribution is modeled according to the Lagrangian Stokes trajectory method. The Results show that the inclusion distribution in the steel ingot is influenced by the flow pattern which is affected by the solidification pattern. Therefore, inclusion distribution could be controlled by the solidification front with the optimization of heat transfer condition such as the hot top design of steel ingot for the high quality steel production. (paper)

  7. The Pindiro Group (Triassic to Early Jurassic Mandawa Basin, southern coastal Tanzania): Definition, palaeoenvironment, and stratigraphy

    Science.gov (United States)

    Hudson, W. E.; Nicholas, C. J.

    2014-04-01

    This paper defines the Pindiro Group of the Mandawa Basin, southern coastal Tanzania based on studies conducted between 2006 and 2009 with the objective of understanding the evolution of this basin. This work draws upon field data, hydrocarbon exploration data, unconventional literature, and the scant published materials available. The paper focuses on the evolution, depositional environments, and definition of the lowermost sedimentary package, which overlies unconformably the metamorphic basement of Precambrian age. The package is described here as the Pindiro Group and it forms the basal group of the Mandawa Basin stratigraphy.

  8. Application potential of sequence stratigraphy to prospecting for sandstone-type uranium deposit in continental depositional basins

    International Nuclear Information System (INIS)

    Li Shengxiang; Chen Zhaobo; Chen Zuyi; Xiang Weidong; Cai Yuqi

    2001-01-01

    Sequence stratigraphy has been widely used in hydrocarbon exploration and development, and great achievements have been achieved. However, its application to the prospecting for sandstone-type uranium deposits is just beginning. The metallogenic characteristics of sandstone-type uranium deposits and those of oil and gas are compared, and the relationship between sandstone-type uranium metallogenesis and the system tracts of sequence stratigraphy is studied. The authors propose that highest and system tracts are the main targets for prospecting interlayer oxidation zone type sandstone uranium deposits, and the incised valleys of low stand system tracts are favourable places for phreatic oxidation zone type sandstone uranium deposits, and transgressive system tracts are generally unfavorable to the formation of in-situ leachable sandstone-type uranium deposits. Finally, the authors look ahead the application potential of sequence stratigraphy to the prospecting for sandstone-type uranium deposits in continental depositional basins

  9. Creative Educational Practices for Inclusion

    Science.gov (United States)

    Piske, Fernanda Hellen Ribeiro; Stoltz, Tania; Machado, Jarci

    2014-01-01

    Inclusion of gifted students depends on several aspects to happen in the school context, and one of the most important aspects to include these children at school is creative educational practices. Teaching with art is a good possibility to make children feel motivated to attend school. In the school context, the inclusion of these children could…

  10. Early Childhood Inclusion in Turkey

    Science.gov (United States)

    Diken, Ibrahim H.; Rakap, Salih; Diken, Ozlem; Tomris, Gozde; Celik, Secil

    2016-01-01

    Inclusion of young children with disabilities into regular preschool classrooms is a common practice that has been implemented for several decades in industrialized nations around the world, and many developing countries including Turkey have been developing and implementing laws, regulation, and services to support inclusion and teaching in…

  11. Inclusion in Malaysian Integrated Preschools

    Science.gov (United States)

    Sukumaran, Sailajah; Loveridge, Judith; Green, Vanessa A.

    2015-01-01

    Inclusive education has been introduced through a number of policy developments in Malaysia over the last 10 years but there is little research investigating the extent and nature of inclusive education for preschoolers with special educational needs (SEN). This study surveyed both regular and special education teachers in Malaysian integrated…

  12. Early Childhood Inclusion in Spain

    Science.gov (United States)

    Giné, Climent; Balcells-Balcells, Anna; Cañadas, Margarita; Paniagua, Gema

    2016-01-01

    This article describes early childhood inclusion in educational settings in Spain. First, we address the legislative framework of preschool education in Spain and offer a brief analysis of some relevant issues, including the current situation of early childhood education and inclusion at this stage. Second, current policies and practices relating…

  13. Social Inclusion and Metrolingual Practices

    Science.gov (United States)

    Otsuji, Emi; Pennycook, Alastair

    2011-01-01

    In this paper, we explore the implications of metrolingual language practices for how we understand social inclusion. A vision of social inclusion that includes bi- and multilingual capacities may comprise an appreciation of a diversity of languages other than English, and the skills and capabilities of multilingual language users, yet it is all…

  14. Gyroelastic fluids

    Energy Technology Data Exchange (ETDEWEB)

    Kerbel, G.D.

    1981-01-20

    A study is made of a scale model in three dimensions of a guiding center plasma within the purview of gyroelastic (also known as finite gyroradius-near theta pinch) magnetohydrodynamics. The (nonlinear) system sustains a particular symmetry called isorrhopy which permits the decoupling of fluid modes from drift modes. Isorrhopic equilibria are analyzed within the framework of geometrical optics resulting in (local) dispersion relations and ray constants. A general scheme is developed to evolve an arbitrary linear perturbation of a screwpinch equilibrium as an invertible integral transform (over the complete set of generalized eigenfunctions defined naturally by the equilibrium). Details of the structure of the function space and the associated spectra are elucidated. Features of the (global) dispersion relation owing to the presence of gyroelastic stabilization are revealed. An energy principle is developed to study the stability of the tubular screwpinch.

  15. Gyroelastic fluids

    International Nuclear Information System (INIS)

    Kerbel, G.D.

    1981-01-01

    A study is made of a scale model in three dimensions of a guiding center plasma within the purview of gyroelastic (also known as finite gyroradius-near theta pinch) magnetohydrodynamics. The (nonlinear) system sustains a particular symmetry called isorrhopy which permits the decoupling of fluid modes from drift modes. Isorrhopic equilibria are analyzed within the framework of geometrical optics resulting in (local) dispersion relations and ray constants. A general scheme is developed to evolve an arbitrary linear perturbation of a screwpinch equilibrium as an invertible integral transform (over the complete set of generalized eigenfunctions defined naturally by the equilibrium). Details of the structure of the function space and the associated spectra are elucidated. Features of the (global) dispersion relation owing to the presence of gyroelastic stabilization are revealed. An energy principle is developed to study the stability of the tubular screwpinch

  16. The stratigraphy and history of Mars' northern lowlands through mineralogy of impact craters: A comprehensive survey

    Science.gov (United States)

    Pan, Lu; Ehlmann, Bethany L.; Carter, John; Ernst, Carolyn M.

    2017-09-01

    The basin-filling materials of the northern lowlands, which cover approximately one third of Mars' surface, record the long-term evolution of Mars' geology and climate. The buried stratigraphy was inferred through analyses of impact crater mineralogy, detected using data acquired by the Compact Reconnaissance Imaging Spectrometer for Mars. Examining 1045 impact craters across the northern lowlands, we find widespread olivine and pyroxene and diverse hydrated/hydroxylated minerals, including Fe/Mg smectite, chlorite, prehnite, and hydrated silica. The distribution of mafic minerals is consistent with infilling volcanic materials across the entire lowlands ( 1-4 × 107 km3), indicating a significant volume of volatile release by volcanic outgassing. Hydrated/hydroxylated minerals are detected more frequently in large craters, consistent with the scenario that the hydrated minerals are being excavated from deep basement rocks, beneath 1-2 km thick mafic lava flows or volcaniclastic materials. The prevalences of different types of hydrated minerals are similar to statistics from the southern highlands. No evidence of concentrated salt deposits has been found, which would indicate a long-lived global ocean. We also find significant geographical variations of local mineralogy and stratigraphy in different basins (geological provinces), independent of dust cover. For example, many hydrated and mafic minerals are newly discovered within the polar Scandia region (>60°N), and Chryse Planitia has more mafic mineral detections than other basins, possibly due to a previously unrecognized volcanic source.

  17. Coastal barrier stratigraphy for Holocene high-resolution sea-level reconstruction.

    Science.gov (United States)

    Costas, Susana; Ferreira, Óscar; Plomaritis, Theocharis A; Leorri, Eduardo

    2016-12-08

    The uncertainties surrounding present and future sea-level rise have revived the debate around sea-level changes through the deglaciation and mid- to late Holocene, from which arises a need for high-quality reconstructions of regional sea level. Here, we explore the stratigraphy of a sandy barrier to identify the best sea-level indicators and provide a new sea-level reconstruction for the central Portuguese coast over the past 6.5 ka. The selected indicators represent morphological features extracted from coastal barrier stratigraphy, beach berm and dune-beach contact. These features were mapped from high-resolution ground penetrating radar images of the subsurface and transformed into sea-level indicators through comparison with modern analogs and a chronology based on optically stimulated luminescence ages. Our reconstructions document a continuous but slow sea-level rise after 6.5 ka with an accumulated change in elevation of about 2 m. In the context of SW Europe, our results show good agreement with previous studies, including the Tagus isostatic model, with minor discrepancies that demand further improvement of regional models. This work reinforces the potential of barrier indicators to accurately reconstruct high-resolution mid- to late Holocene sea-level changes through simple approaches.

  18. The infidelity of melt inclusions?

    Science.gov (United States)

    Kent, A. J.

    2008-12-01

    Melt inclusions provide important information about magmatic systems and represent unique records of magma composition and evolution. However, it is also clear that melt inclusions do not necessarily constitute a petrological 'magic bullet', and potential exists for trapped melt compositions to be modified by a range of inclusion-specific processes. These include trapping of diffusional boundary layers, crystallization of the host mineral after trapping and dissolution of co-trapped minerals during homogenization, diffusional exchange between trapped liquid and the host mineral and external melt, and cryptic alteration of trapped material during weathering or hydrothermal alteration. It clearly important to identify when melt inclusions are unmodified, and which compositional indices represent the most robust sources of petrogenetic information. In this presentation I review and discuss various approaches for evaluating compositions and compositional variations in inclusion suites. An overriding principle is that the variations evident in melt inclusions should be able to be understood in terms of petrological processes that are known, or can be reasonably inferred to also effect bulk magma compositions. One common approach is to base petrological conclusions on species that should be more robust, and many workers use variations in incompatible trace elements for this purpose. However important information may also be obtained from a comparison of variations in melt inclusions and the lavas that host them, and in most cases this comparison is the key to identifying inclusions and suites that are potentially suspect. Comparisons can be made between individual inclusions and lavas, although comparison of average inclusion composition and the host lava, after correction for differences in crystal fractionation, may also be valuable. An important extension of this is the comparison of the variability of different species in inclusions and host lavas. This also provides

  19. Can Inclusions Survive To The Ends Of The Earth?

    Science.gov (United States)

    Taylor, R.

    2017-12-01

    Many petrological, geochemical, and paleomagnetic studies are now focussing on the inclusions that are hosted within other minerals. This approach comes with the benefit that the inclusion can be protected or `armoured' from further external influences subsequent to its encapsulation within a host phase. An armoured inclusion may retain genuine primary information, rather than secondary information resulting from alteration by agents such as aqueous fluids. A key player in the role of the host mineral is zircon, being regarded as "ultrastable" with both physical and chemical resilience. Most importantly zircon is common in many rock types and is widely considered our primary U-­Pb geochronometer in ancient rocks. However this blessing is also its curse, U-decay can result in the accumulation of severe radiation damage over extreme lengths of time, potentially rendering the ultrastable host incapable of protecting its inclusions. Magnetic inclusions, such as magnetite, in zircon are pushing back the boundaries of our understanding of the Earth's magnetic field. The oldest zircon grains from Western Australia predate the most ancient rock record by c. 500 Myr, meaning that magnetic data from inclusions in such grains can push our paleomagnetic record into the Hadean. However few studies thus far have focussed on nature of the Fe-bearing inclusions in terms of their susceptibility to secondary alteration during their long history. Here we present 2D, 3D and isotopic data from inclusions and other internal features of the host zircon and investigate the characteristic features of primary vs secondary Fe-bearing material that may hold clues to early Earth history. Archean grains up to 3 Ga from NW Scotland are used as analogues for the rare Jack Hills material, and allow investigation of Fe alteration from source to sink. Inclusions and potential fluid infiltration networks are imaged in 3D by synchrotron x-ray micro computed tomography. These 3D images are compared to

  20. Ca isotopes in refractory inclusions

    International Nuclear Information System (INIS)

    Niederer, F.R.; Papanastassiou, D.A.

    1984-01-01

    We report measurements of the absolute isotope abundance of Ca in Ca-Al-rich inclusions from the Allende and Leoville meteorites. Improved high precision measurements are reported also for 46 Ca. We find that nonlinear isotope effects in Ca are extremely rare in these inclusions. The absence of nonlinear effects in Ca, except for the effects in FUN inclusions, is in sharp contrast to the endemic effects in Ti. One fine-grained inclusion shows an excess of 46 Ca of (7 +- 1) per mille, which is consistent with addition of only 46 Ca or of an exotic (*) component with 46 Ca* approx. 48 Ca*. FUN inclusion EK-1-4-1 shows a small 46 Ca excess of (3.3 +- 1.0) per mille; this confirms that the exotic Ca components in EK-1-4-1 were even more deficient in 46 Ca relative to 48 Ca than is the case for normal Ca. The Ca in the Ca-Al-rich inclusions shows mass dependent isotope fractionation effects which have a range from -3.8 to +6.7 per mille per mass unit difference. This range is a factor of 20 wider than the range previously established for bulk meteorites and for terrestrial and lunar samples. Ca and Mg isotope fractionation effects in the Ca-Al-rich inclusions are common and attributed to kinetic isotope effects. (author)

  1. Inclusive education and social exclusion

    Directory of Open Access Journals (Sweden)

    Maria Luisa Bissoto

    2013-01-01

    Full Text Available The aim of this paper is critically examining assumptions underlying the Inclusive Education concept, arguing that this can only be effectively considered when understood in a broader context of social inclusion and exclusion. Methodologically, this article relies on international documents and bibliographic references about Inclusive Education, that have been chosen by systematize and characterize different social and educational inclusive practices, encouraging the elaboration of a general overview on this topic. The results of this analysis conclude that it is essential for Inclusive Education that educational institutions review their goals and reasons of social existence. In the concluding remarks it is argued that education is better understood as the act of encouraging and welcoming the efforts of individuals in their attempts to engage in social networking, which sustains life. This includes the acceptance of other reality interpretations and understanding that educational action cannot be restricted by the walls of institutions. It requires the participation of the whole community. Action perspectives likely to promote social inclusion and inclusive education are suggested.

  2. Thermophysical Properties of Fluids and Fluid Mixtures

    Energy Technology Data Exchange (ETDEWEB)

    Sengers, Jan V.; Anisimov, Mikhail A.

    2004-05-03

    The major goal of the project was to study the effect of critical fluctuations on the thermophysical properties and phase behavior of fluids and fluid mixtures. Long-range fluctuations appear because of the presence of critical phase transitions. A global theory of critical fluctuations was developed and applied to represent thermodynamic properties and transport properties of molecular fluids and fluid mixtures. In the second phase of the project, the theory was extended to deal with critical fluctuations in complex fluids such as polymer solutions and electrolyte solutions. The theoretical predictions have been confirmed by computer simulations and by light-scattering experiments. Fluctuations in fluids in nonequilibrium states have also been investigated.

  3. Politics of Inclusion and Empowerment

    DEFF Research Database (Denmark)

    Andersen, John; Siim, Birte

    2004-01-01

    The objective of the book is to analyse different politics of inclusion and empowerment and the different paradigms of inclusion/exclusion in order to underline the close link between politics of scoial equality and politics of recognition of ciultural difference. Politics of inclusion is thus...... theproductive/innovative linkage of politics of redistributuin and politics og resognition, whnich over a longer time span creates sustainable paths of democratic and social development, which increases the capacity to handle both conflicts about economic resources and life-chances and conflicts about...

  4. Automatic fluid dispenser

    Science.gov (United States)

    Sakellaris, P. C. (Inventor)

    1977-01-01

    Fluid automatically flows to individual dispensing units at predetermined times from a fluid supply and is available only for a predetermined interval of time after which an automatic control causes the fluid to drain from the individual dispensing units. Fluid deprivation continues until the beginning of a new cycle when the fluid is once again automatically made available at the individual dispensing units.

  5. Micro-Raman densimeter for CO2 inclusions in mantle-derived minerals.

    Science.gov (United States)

    Kawakami, Yoko; Yamamoto, Junji; Kagi, Hiroyuki

    2003-11-01

    We investigated the applicability of Raman microprobe spectroscopy for determining the density of CO2 in fluid inclusions in minerals of mantle-derived xenolith samples. A separation (delta) between two Raman bands of CO2 due to Fermi resonance can be a reliable densimeter for CO2 fluid. The relationship between the density of CO2 (g/cm3) and delta (cm-1) can be expressed as: d = -0.03238697 delta 3 + 10.08428 delta 2 - 1046.189 delta + 36163.67. This equation was obtained from the Raman data on CO2 fluid with densities from 0.1 to 1.21 g/cm3, including super critical fluids at 58-59 degrees C. The delta value was constant with increasing temperature from room temperature to 200 degrees C. This indicates that the Raman densimeter is not affected by a possible rise in temperature, an artifact induced by the high flux of the incident laser. The minimum size of measurable inclusions is 1 micron, and the precision in the determination of delta is 0.1 cm-1, corresponding to 0.02 g/cm3 for inclusions of 1 micron in size. The precision can be better for larger inclusions. The micro-Raman densimeter can determine the density of CO2 fluid inclusions over a wide range. In particular, densities of gas and mixtures of gas and liquid phases, which cannot be measured by microthermometry, can be determined.

  6. Carbon Dioxide: The Other Planetary Fluid

    Science.gov (United States)

    Glaser, S.; Gamez, D.; Shock, E.

    2016-12-01

    Cometary and interstellar ices have carbon dioxide to water mole ratios of up to 0.3. When melted, such high levels of carbon dioxide cannot all be dissolved in the aqueous phase and instead partition into a CO2-rich (carbonic) fluid. This implies that during the accretion and formation of planetary systems carbonic fluids are not only possible, but common. In fact, they make up the atmosphere of Venus, are found bubbling out of Champagne Vent in the Pacific Ocean, and are documented by metamorphic fluid inclusions. Examination of phase diagrams reveals the conditions where carbonic fluids will exist or predominate. Carbonic fluids are predicted to exist in Earth's subduction zones and under the ice of small ocean worlds. CO2 had previously been shown to completely dissolve into NH­­3­-H­­2O oceans on small icy bodies by forming ammonium carbonate, but the newer measurements of CO2­ abundances indicate that not all of the CO2 can partition into the aqueous fluid as ammonium carbonate. The remaining CO2 would necessarily form a separate carbonic fluid making it likely that liquid CO2 would be a major oceanic component on some small icy bodies. The enhanced solubility of nonpolar and slightly polar organic compounds in carbonic fluids relative to aqueous fluids means that generation, transport, and deposition processes can be greatly enhanced in those cases where carbonic fluids occur. As an example, the solubility of benzoic acid, a polar compound, is about an order of magnitude greater in carbonic than in aqueous fluids, which is surprising given that water is a polar solvent and carbon dioxide is a nonpolar solvent. Anthracene, a nonpolar compound, has an even greater solubility difference between carbonic and aqueous fluids at approximately four orders of magnitude. Highly polar compounds, including most of the building blocks of life, are more soluble in aqueous fluids than in carbonic fluids. The solubility difference of organic molecules in carbonic

  7. Inclusão e governamentalidade Inclusion and governmentality

    Directory of Open Access Journals (Sweden)

    Alfredo Veiga-Neto

    2007-10-01

    Full Text Available O artigo parte dos conceitos de governamento, biopoder, norma e governamentalidade para argumentar no sentido de que as políticas de inclusão - especialmente as políticas de inclusão escolar - são dispositivos biopolíticos para o governamento e o controle das populações. Tomam-se esses e outros conceitos foucaultianos como ferramentas analíticas para argumentar que é preciso examinar as políticas e práticas inclusivas sem assumir antecipadamente qualquer juízo de valor sobre elas. Entendendo a diferença como manifestação da diversidade, e o diferente como um exótico, um portador de algo que os outros não possuem, as políticas de inclusão - nos modos como vêm sendo formuladas e em parte executadas no Brasil - parecem ignorar a própria diferença. Assim, ao invés de promoverem uma educação para todos, elas correm o risco de realizar uma inclusão excludente das diferenças. Discute-se a distinção entre campanhas públicas e políticas de inclusão em termos dos âmbitos em que ambas se efetivam.Based on the concepts of government, biopower, norm and governmentality, this paper argues that the inclusion policies - especially those of school inclusion - are biopolitical devices to govern and control the populations. These and other concepts by Foucault are used as analytical tools to argue that we have to explore the including policies and practices without any previous value judgment on them. Since they understand the difference as a manifestation of diversity, and the different as the exotic, what carries something the others do not have, the inclusion policies - as they are being formulated and partly enforced in Brazil - seem to ignore difference itself. Thus, instead of promoting education for all, they may lead to an inclusion that excludes the differences. The text finally discusses the distinction between public campaigns and inclusion policies in terms of the settings in which both take place.

  8. Inclusion for Customer with Disabilities

    OpenAIRE

    Murphy, James Peter

    2010-01-01

    For many people with disabilities, licensed premises design and lack of sufficient staff training can act as powerful barriers to their full inclusion in the activities of bars, restaurants and nightclubs.

  9. EDUCATIONAL INCLUSION AND CRITICAL PEDAGOGY

    Directory of Open Access Journals (Sweden)

    Silvia Molina

    2009-11-01

    Full Text Available This article outlines the basic principles of educational inclusion, focusingspecifically on the inclusion of disabled students in mainstream classrooms, and arguesthat inclusive education should be understood as a process of transforming traditionalschools into spaces of learning for all students. The article uses the lens of critical pedagogyto argue that exclusionary educational practices have been developed through themedicalization of learning disabilities which focused on the disability rather than theabilities of disabled students. Following the same line of thinking, the article providesscientific evidence to debunk myths related to the education of disabled students; especiallymyths that contributed to their exclusion from mainstream classrooms. Finally,based on the Learning Communities model, we provide some concrete strategies fortransforming mainstream classrooms into fully inclusive environments.

  10. An attempt at correlation between the Velay pollen sequence and the Middle Pleistocene stratigraphy from central Europe

    Czech Academy of Sciences Publication Activity Database

    de Beaulieu, J. L.; Andrieu-Ponel, V.; Reille, M.; Grüger, E.; Tzedakis, C.; Svobodová, Helena

    2001-01-01

    Roč. 20, - (2001), s. 1593-1602 ISSN 0277-3791 R&D Projects: GA AV ČR KSK6005114 Institutional research plan: CEZ:AV0Z6005908 Keywords : Middle Pleistocene * stratigraphy * pollen sequence Subject RIV: EF - Botanics Impact factor: 3.055, year: 2001

  11. Upper Campanian–Maastrichtian nannofossil biostratigraphy and high-resolution carbon-isotope stratigraphy of the Danish Basin

    DEFF Research Database (Denmark)

    Thibault, Nicolas Rudolph; Harlou, Rikke; Schovsbo, Niels

    2012-01-01

    High-resolution carbon isotope stratigraphy of the upper Campanian – Maastrichtian is recorded in the Boreal Realm from a total of 1968 bulk chalk samples of the Stevns-1 core, eastern Denmark. Isotopic trends are calibrated by calcareous nannofossil bio-events and are correlated with a lower-res...

  12. Subsurface stratigraphy and structure of A/M area at the Savannah River Site, Aiken County, South Carolina. Final report

    Energy Technology Data Exchange (ETDEWEB)

    Fallaw, W.C.; Sims, W.R.; Haselow, J.S.

    1991-08-01

    This report is a study of the stratigraphy and structure of the A/M Area Hazardous Waste Management Facility Post-Closure Care Permit process on the Savannah River Site. The data from the lithologic and geophysical logs of 93 wells is the basis of this analysis.

  13. Subsurface stratigraphy and structure of A/M area at the Savannah River Site, Aiken County, South Carolina

    Energy Technology Data Exchange (ETDEWEB)

    Fallaw, W.C.; Sims, W.R.; Haselow, J.S.

    1991-08-01

    This report is a study of the stratigraphy and structure of the A/M Area Hazardous Waste Management Facility Post-Closure Care Permit process on the Savannah River Site. The data from the lithologic and geophysical logs of 93 wells is the basis of this analysis.

  14. Sequence Stratigraphy of the Dakota Sandstone, Eastern San Juan Basin, New Mexico, and its Relationship to Reservoir Compartmentalization

    Energy Technology Data Exchange (ETDEWEB)

    Varney, Peter J.

    2002-04-23

    This research established the Dakota-outcrop sequence stratigraphy in part of the eastern San Juan Basin, New Mexico, and relates reservoir quality lithologies in depositional sequences to structure and reservoir compartmentalization in the South Lindrith Field area. The result was a predictive tool that will help guide further exploration and development.

  15. Integrated stratigraphy of the Jurassic-Cretaceous sequences of the Kurovice Quarry, Outer Western Carpathians: correlations and tectonic implications

    Czech Academy of Sciences Publication Activity Database

    Pruner, Petr; Schnabl, Petr; Čížková, Kristýna; Elbra, Tiiu; Kdýr, Šimon; Svobodová, Andrea; Reháková, D.

    2017-01-01

    Roč. 120 (2017), s. 216-216 ISSN 1017-8880. [International Symposium on the Cretaceous /10./. 21.08.2017-26.08.2017, Vienna] R&D Projects: GA ČR(CZ) GA16-09979S Institutional support: RVO:67985831 Keywords : stratigraphy * Jurassic-Cretaceous sequences * Western Carpathians Subject RIV: DB - Geology ; Mineralogy

  16. Origin, sequence stratigraphy and depositional environment of an Upper Ordovician (Hirnantian) deglacial black shale, Jordan-Discussion

    Czech Academy of Sciences Publication Activity Database

    Lüning, S.; Loydell, D. K.; Štorch, Petr; Shahin, Y.; Craig, J.

    2006-01-01

    Roč. 230, 3-4 (2006), s. 352-355 ISSN 0031-0182 Institutional research plan: CEZ:AV0Z30130516 Keywords : Silurian * black shale * sequence stratigraphy Subject RIV: DB - Geology ; Mineralogy Impact factor: 1.822, year: 2006

  17. Carbon isotope stratigraphy, magnetostratigraphy, and 40Ar/39Ar age of the Cretaceous South Atlantic coast, Namibe Basin, Angola

    NARCIS (Netherlands)

    Strganac, Christopher; Salminen, Johanna; Jacobs, Louis L.; Polcyn, Michael J.; Ferguson, Kurt M.; Mateus, Octávio; Schulp, Anne S.; Morais, Maria Luísa; Tavares, Tatiana da Silva; Gonçalves, António Olímpio

    2014-01-01

    We present the δ13C and paleomagnetic stratigraphy for marine strata at the coast of southern Angola, anchored by an intercalated basalt with a whole rock 40Ar/39Ar radiometric age of 84.6 ± 1.5 Ma, being consistent with both invertebrate and vertebrate biostratigraphy. This is the first African

  18. Fluid Mechanics and Fluid Power (FMFP)

    Indian Academy of Sciences (India)

    Amitabh Bhattacharya

    decades, mainly due to the rapid improvement in computational efficiency, cameras, optics and instrumentation, both computational and experimental techniques have improved significantly, allowing researchers in Fluid Mechanics to build better mechanistic and analytical models for processes involving dynamics of fluids.

  19. PSYCHOANALYSIS, ETHICS AND INCLUSIVE EDUCATION

    OpenAIRE

    Ana Beatriz Coutinho Lerner; Rinaldo Voltolini

    2016-01-01

    This paper aims to investigate the central ways in which the discourse on Inclusive Education assumes in contemporary times and some the effects of this discourse on the subjectivity of children, parents and school professionals. In order to accomplish this goal, we first review the literature concerning Inclusive Education, showing the origins of this movement, the main legal frameworks that organize this subject and the current theoretical perspectives. We then analyze discursive elements c...

  20. Forum, Dedicated to Inclusive Education

    Directory of Open Access Journals (Sweden)

    Vachkov I.V.

    2015-06-01

    Full Text Available 26 – 27 of February 2015 in Kazan, in the University of Management “TISBI” been held National (All-Russian forum of promotion of ideas and principles of inclusive education (with international participants “Study and live together: open space of inclusion”. During the work of Forum the most topical questions of inclusive education implement in Russian Federation been discussed.

  1. Fluid Mechanics and Fluid Power (FMFP)

    Indian Academy of Sciences (India)

    Amitabh Bhattacharya

    of renewable energy (e.g., via wind, hydrokinetic generators), creating low-cost healthcare (e.g., via point-of-care medical testing) and improvement of energy efficiency of fluid power systems, depends on improving our understanding of Fluid. Mechanics. Fluids are ubiquitous in both nature and technological applications, ...

  2. Reconstructing Watershed History from Reservoir Stratigraphy: Englebright Lake, Yuba River, Northern California

    Science.gov (United States)

    Snyder, N. P.; Alpers, C. N.; Childs, J. R.; Curtis, J. A.; Flint, L. E.; Holmes, C. W.; Rubin, D. M.; Wright, S. A.

    2004-12-01

    Reservoirs provide the opportunity to study fluvial processes and rates in a controlled setting because they are effective traps of sediment and are often well monitored. An extensive sediment coring and sampling campaign was done in Englebright Lake on the Yuba River in northern California as part of a fish-habitat restoration study. The Yuba watershed (particularly the southern part) was the site of intensive hydraulic gold mining in the 19th and early 20th century, and Englebright Dam was built in 1940 to trap mining debris. Results of a bathymetric survey in 2001 indicate that the reservoir was 26% full (22x106 m3 of material). The physical properties of the entire deposit were extrapolated from ˜300 m of cores collected at 7 sites along the longitudinal axis of the reservoir in 2002. The mass of the deposit is 26x106 metric tons, of which 3.2% is organic. The sediment is ˜65% sand and gravel, and distinct layers of differing grain size (sand-gravel, silt-clay, organics) are well preserved in the cores. The depositional chronology of the reservoir was established using 137Cs analysis and the relations between the cored stratigraphy and the hydrologic and impoundment history of the watershed. Deposits from three major flood events (1955, 1964, 1997; each with discharge >3,400 m3/s) were identified in the stratigraphy of most of the coring sites. Observations of recent (post-1997) depositional patterns are guiding the development of a conceptual model of reservoir-sedimentation processes during floods, drawdowns, and intraflood periods. Enlargement of an upstream dam on the North Yuba River in 1970 caused a decrease in flood frequency in the Yuba River and changed management of Englebright Lake (ending annual drawdowns). A relict topset-foreset-bottomset sequence observed in the cored stratigraphy is interpreted to correlate with this change in watershed management; a second deltaic sequence was deposited on top of the first after 1970. Post-1970 average annual

  3. Assessing the Crustal Stratigraphy of Mercury: Results from MESSENGER Orbital Observations

    Science.gov (United States)

    Ernst, C. M.; Murchie, S. L.; Barnouin, O. S.; Chabot, N. L.; Denevi, B. W.; Head, J. W.; Klimczak, C.; Prockter, L. M.; Solomon, S. C.; Watters, T. R.

    2011-12-01

    Mariner 10 and MESSENGER flyby images revealed subtle color variations across Mercury's surface, many of which are associated with impact craters and basins. Impact craters that excavated material spectrally distinct from the surrounding pre-impact surface serve as windows into the subsurface, allowing observations of material at depth that would otherwise remain hidden to remote observations. Previous localized studies of spectrally distinct, excavated material suggested the presence of buried volcanic plains and a heterogeneous crustal stratigraphy and support the important role of volcanism in the evolution of the crust. MESSENGER's Mercury Dual Imaging System (MDIS) has since acquired global color (1 km/pixel) and high-resolution monochrome (250 m/pixel) base maps of the innermost planet, taken under illumination and observation geometries optimized for observing both color and morphology. These base maps, along with detailed targeted observations (up to 80 m/pixel color and 10 m/pixel monochrome), allow detailed co-mapping of geologic and spectral features across Mercury's surface. Such mapping, along with the use of scaling laws and melt-volume calculations to bound the depth of origin of crater ejecta and central peak structures, allows us to investigate many aspects of Mercury's crustal stratigraphy, including, but not limited to, the following topics: (1) The stratigraphy of four of Mercury's younger large basins: Caloris (1550 km in diameter), Rembrandt (720 km), Beethoven (630 km), and Tolstoj (360 km), which have all been flooded by spectrally distinct volcanic plains. Post-flooding craters of varying sizes enable an estimation of the thickness of the volcanic fill and the nature of the pre-flooding basin floor. These measurements will help to constrain models for subsequent compensation, uplift, and deformation; and incorporation of topography and gravity data link basin fill with the broader lithospheric evolution of Mercury. (2) The depth of origin

  4. Holocene alluvial stratigraphy in the upper Susquehanna River Basin, New York*1

    Science.gov (United States)

    Scully, Richard W.; Arnold, Richard W.

    1981-05-01

    Two alluvial terraces and the present flood plain were studied at two locations along the Susquehanna and Unadilla Rivers in south-central New York state. They have formed since deglaciation and incision of the stream channels into the valley train deposits. The higher terrace has noncumulative soil profiles with well-developed color B horizons predominantly of silt loam and very fine sandy loam. The terrace is weathered to a degree similar to nearby glacial outwash terraces that have caps of similarly textured sediments. Incision that produced the terrace occurred before 9705 ± 130 yr B.P. The lower terrace is characterized by relatively thick, vertical-accretion deposits of silt loam that contain sequences of thin, buried A, color B, and C horizons. They were formed between about 3240 ± 110 ( 14C data of soil humin) and 235 ± 80 yr B.P. Deposits above the 235 ± 80 yr B.P. stratum are unweathered. The soil stratigraphy and 14C dates of soil humin from buried A horizons are surprisingly well correlated between sites. Most sediments of the present flood plain have been deposited since 1120 ± 80 yr B.P. Incipient A horizons and oxidation of inherited organic matter in the subsoil are the only evidence of pedogenesis in the flood-plain deposits that are older than 275 ± 80 yr B.P. The most recent flood-plain fill deposited since then is unaltered. These youngest sediments of the flood plain along with the youngest veneer of vertical-accretion deposits on the lowest terrace are associated with an increased rate of deposition largely attributable to clearing of the forests by settlers, beginning in the late 1700s. Comparison of the alluvial stratigraphy with the radiocarbon-dated pollen stratigraphy of southwestern New York (Miller 1973) reveals some apparent time correlations between alluvial events and vegetation changes. This gives reason to speculate that climatic change or forest catastrophes such as disease or drought are causes of some of the alluvial

  5. Modeling growth and dissolution of inclusions during fusion welding of steels

    Science.gov (United States)

    Hong, Tao

    The characteristics of inclusions in the weld metals are critical factors to determine the structure, properties and performance of weldments. The research in the present thesis applied computational modeling to study inclusion behavior considering thermodynamics and kinetics of nucleation, growth and dissolution of inclusion along its trajectory calculated from the heat transfer and fluid flow model in the weld pool. The objective of this research is to predict the characteristics of inclusions, such as composition, size distribution, and number density in the weld metal from different welding parameters and steel compositions. To synthesize the knowledge of thermodynamics and kinetics of nucleation, growth and dissolution of inclusion in the liquid metal, a set of time-temperature-transformation (TTT) diagrams are constructed to represent the effects of time and temperature on the isothermal growth and dissolution behavior of fourteen types of individual inclusions. The non-isothermal behavior of growth and dissolution of inclusions is predicted from their isothermal behavior by constructing continuous-cooling-transformation (CCT) diagrams using Scheil additive rule. A well verified fluid flow and heat transfer model developed at Penn State is used to calculate the temperature and velocity fields in the weld pool for different welding processes. A turbulent model considering enhanced viscosity and thermal conductivity (k-ε model) is applied. The calculations show that there is vigorous circulation of metal in the weld pool. The heat transfer and fluid flow model helps to understand not only the fundamentals of the physical phenomena (luring welding, but also the basis to study the growth and dissolution of inclusions. The calculations of particle tracking of thousands of inclusions show that most inclusions undergo complex gyrations and thermal cycles in the weld pool. The inclusions experience both growth and dissolution during their lifetime. Thermal cycles of

  6. Natural occurrence and significance of fluids indicating high pressure and temperature

    Science.gov (United States)

    Roedder, E.

    1981-01-01

    Most natural minerals have formed from a fluid phase such as a silicate melt or a saline aqueous solution. Fluid inclusions are tiny volumes of such fluids that were trapped within the growing crystals. These inclusions can provide valuable but sometimes ambiguous data on the temperature, pressure, and composition of these fluids, many of which are not available from any other source. They also provide "visual autoclaves" in which it is possible to watch, through the microscope, the actual phase changes take place as the inclusions are heated. This paper reviews the methods of study and the results obtained, mainly on inclusions formed from highly concentrated solutions, at temperatures ???500??C. Many such fluids have formed as a result of immiscibility with silicate melt in igneous or high-temperature metamorphic rocks. These include fluids consisting of CO2, H2O, or hydrosaline melts that were <50% H2O. From the fluid inclusion evidence it is clear that a boiling, very hot, very saline fluid was present during the formation of most of the porphyry copper deposits in the world. Similarly, from the inclusion evidence it is clear that early (common) pegmatites formed from essentially silicate melts and that the late, rare-element-bearing and chamber-type pegmatites formed from a hydrosaline melt or a more dilute water solution. The evidence on whether this change in composition from early to late solutions was generally continuous or involved immiscibility is not as clear. ?? 1981.

  7. Seismic stratigraphy and deformational styles of the offshore Cyrenaica (Libya) and bordering Mediterranean Ridge

    Science.gov (United States)

    Yem, Lionel Mbida; Camera, Laurent; Mascle, Jean; Ribodetti, Alessandra

    2011-04-01

    Off northwest Libya the Cyrenaica foreland basin domain and its Pan-African continental crust, which constitute the African promontory, are overthrusted by the Mediterranean Ridge Complex. The thrust belt contact and its seismic stratigraphy have been analysed using pre-stack depth-migrated multichannel seismic (MCS) lines recorded during the MEDISIS survey (2002). The geometry and sedimentary distribution analysis through the wedge-top depocentres allow reconstruction of schematic cross-sections of the tectono-sedimentary wedge that includes two major thrust sequences separated by an apparently poorly deformed transition zone. Based on time-space variation of several piggyback basins, we propose that these thrust sequences relate to distinct phases of shortening. (1) A first event, which probably occurred just prior to the Messinian crisis in latest Miocene (Tortonian times?) and (2) A second event, that has finally led to the present-day overthrusting of the Mediterranean Ridge over the Libyan continental slope.

  8. Holocene stratigraphy and vegetation history in the Scoresby Sund area, East Greenland

    DEFF Research Database (Denmark)

    Funder, Svend Visby

    1978-01-01

    The Holocene stratigraphy in Scoresby Sund is based on climatic change as reflected by fluctuations in fjord and valley glaciers, immigration and extinction of marine molluscs, and the vegetation history recorded in pollen diagrams from five lakes. The histories are dated by C-14, and indirectly...... into the area, and in the period until 5000 yr BP dense dwarf shrub heath grew in areaS where it is now absent. In the fjords the subarctic Mytilus edulis and Pecten islandica lived, suggesting a climate warmer than the present. From c. 5000 yr BP the dense dwarf shrub heath began to disappear in the coastal...... areas, and a 'poor' heath dominated by the high arctic Salix Arctica and Cassiope tetragona expanded. These two species, which are now extremely common, apparently did not grow in the area until c. 6000 yrBP. In lakes in the coastal area minerogenic sedimentation at c. 2800 yr BP, reflecting the general...

  9. The sedimentology and stratigraphy of the Early Tertiary, Cusiana field, Colombia

    International Nuclear Information System (INIS)

    Pulham, Andrew J.

    1995-01-01

    The cusiana field (BP, Ecopetrol, Total and Triton is located in the llanos foothills of Eastern Colombia. There are three key reservoirs in the Cusiana field; the late Eocene to Early Oligocene Mirador Formation, the late Paleocene Barco Formation and the Santonian to Late Campanian Guadalupe Formation. The Mirador Formation contains over 50% of the original oil in place. Production for 1995 is planned at 130.000 barrels of oil per day (bopd; daily average), principally for the Mirador Formation with some production from the Guadalupe Formation. The mirador formation has therefore been the focus of a detailed reservoir description study aimed at understanding reservoir performance and putting a foundation in place for long-term reservoir management. The Mirador Formation comprises sandy (>60%), high frequency sequences dominated by the deposits of incised valleys. This paper describes the sedimentology and stratigraphy of the Mirador and the methodology chosen to construct a reservoir model fit for reservoir simulation

  10. Stratigraphy, petrology, and tectonic setting of the Alisitos Group, Baja California, Mexico

    Science.gov (United States)

    Beggs, J. M.

    The Alisitos Group comprises much of the wall-rocks of the western Peninsular Ranges Batholith in Baja California, Mexico; aspects of its stratigraphy, petrology, and tectonic origin are discussed. The Alisitos group was formerly designated Alisitos Formation. A higher rank of stratigraphic nomenclature is suggested because of its wide extent and lithologic diversity. Two new formations are defined within the Alisitos Group in the San Fernando area. The El Progreso Formation includes volcanic and volcaniclastic rocks mainly of silicic composition interstratified with rudist limestones. The type area is the El Progreso area. It is overlain to the southwest by the San Felipito Formation, which includes tuff-breccia, graded tuff beds, and shale as principal rock types. The main canyon of Arroyo San Fernando is designated as type area.

  11. Carboniferous-Permian sedimentology and stratigraphy of the Nordfjorden High and Loppa Spur, Arctic Norway

    DEFF Research Database (Denmark)

    Ahlborn, Morten

    Abstract (shortened) Facies analysis of Late Paleozoic warm-water carbonates, were conducted in order to investigate the depositional evolution, cyclicity, internal architecture and sequence stratigraphy of the upper Gipsdalen Group carbonate platform on the Nordfjorden High in central Spitsbergen....... In addition a 3D seismic analysis of the offshore northeastern Loppa High was carried out to investigate a hitherto undescribed Late Paleozoic carbonate-dominated succession in the southwestern Barents Sea Shelf. The Late Paleozoic carbonates of the Gipsdalen Group have previously been studied in great detail...... in central Spitsbergen and offshore in the Barents Sea using well data and seismic analysis. These studies have mainly focused on the tectonic development, depositional evolution and the sedimentary facies of the Late Paleozoic succession and have greatly improved the overall perception of the evolution...

  12. Silurian sequence stratigraphy in the North American craton, Great Lakes area

    Science.gov (United States)

    Shaver, R.H.; ,

    1996-01-01

    A notable circumstance of late Early through Late Silurian sedimentation on the Great Lakes area craton is that at least two and possibly three cycles of third-order duration (if eustatically considered) are recognized in basin and shallow-platform settings alike. Both virtually pure and siliciclastic-rich carbonate rocks exist in parts of platform-situated sections in contrast to siliciclastic-rich to evaporite-dominated basin sections. Knowledge of the reef history, together with evidence of incidental periodic incursions of siliciclastic sediments, permitted understanding of a regional event or sequence stratigraphy more than 15 years ago before conventional biostratigraphic and physical stratigraphic evidence became adequate to corroborate. This midwestern US and Ontario Silurian record has become strategic for testing different schools of thought that champion either tectonism or eustasy to explain cyclical sequences.

  13. In situ non-invasive EDXRF analysis to reconstruct stratigraphy and thickness of Renaissance pictorial multilayers

    International Nuclear Information System (INIS)

    Bonizzoni, L.; Poldi, G.; Milazzo, M.; Galli, A.

    2007-01-01

    In this paper, we report a few examples showing how energy dispersive XRF analysis (EDXRF) coupled with visible reflectance spectroscopy (vis-RS) can be successfully applied for the investigation of wood or canvas paintings by performing stratigraphic analyses with non-invasive techniques. The specific aim is to reconstruct layers and their thicknesses. The method has been tested in the laboratory on paint layers similar to traditional Renaissance ones. In situ analyses of a famous wood painting by Andrea Mantegna - 'Madonna col bambino e un coro di cherubini', Pinacoteca di Brera, Milan - were also carried out. While illustrating the results concerning the identification of pigments and the discrimination of layer stratigraphy, advantages and limitation of this method are pointed out. (authors)

  14. Stratigraphy of Venusian Plains: Comparison of Price [1995] and Basilevsky and Head [1995] Units

    Science.gov (United States)

    Basilevsky, A. T.; Burba, G. A.; Kryuchkov, V. P.

    1996-03-01

    A comparison of the Price map, in which plains units were identified based on the prominence of lava flow morphology, with the Kryuchkov map, based on Basilevsky and Head model of Venus stratigraphy, revealed that at least in the area under study (40-80 degrees N, 140-260 degrees E) the plains units of Price are mixtures of formations of different ages. Her approach provides evidently the generally correct ranging of large regions of the planet according to their average age but it misses the key events of the geologic history of Venus such as an emplacement of distinctive stratigraphic members of the venusian plains. This should be taken into account when the determined crater densities and corresponding ages are interpreted.

  15. In situ non-invasive EDXRF analysis to reconstruct stratigraphy and thickness of Renaissance pictorial multilayers

    Energy Technology Data Exchange (ETDEWEB)

    Bonizzoni, L.; Poldi, G.; Milazzo, M. [Istituto di Fisica Generale Applicata, Universita' degli Studi di Milano, via Celoria 16, 20133 Milano (Italy); Galli, A. [CNR-INFM, Dipartimento di Scienza dei Materiali, Universita' degli Studi di Milano-Bicocca, via R. Cozzi 53, 20125 Milano (Italy)

    2007-03-15

    In this paper, we report a few examples showing how energy dispersive XRF analysis (EDXRF) coupled with visible reflectance spectroscopy (vis-RS) can be successfully applied for the investigation of wood or canvas paintings by performing stratigraphic analyses with non-invasive techniques. The specific aim is to reconstruct layers and their thicknesses. The method has been tested in the laboratory on paint layers similar to traditional Renaissance ones. In situ analyses of a famous wood painting by Andrea Mantegna - 'Madonna col bambino e un coro di cherubini', Pinacoteca di Brera, Milan - were also carried out. While illustrating the results concerning the identification of pigments and the discrimination of layer stratigraphy, advantages and limitation of this method are pointed out. (authors)

  16. Ice stratigraphy at the Pakitsoq ice margin, West Greenland, derived from gas records

    DEFF Research Database (Denmark)

    Schaefer, H.; Petrenko, V. V.; Brook, E. J.

    2009-01-01

    Horizontal ice-core sites, where ancient ice is exposed at the glacier surface, offer unique opportunities for paleo-studies of trace components requiring large sample volumes. Following previous work at the Pakitsoq ice margin in West Greenland, we use a combination of geochemical parameters...... measured in the ice matrix (delta O-18(ice)) and air occlusions (delta O-18(atm), delta N-15 of N-2 and methane concentration) to date ice layers from specific climatic intervals. The data presented here expand our understanding of the stratigraphy and three-dimensional structure of ice layers outcropping...... at Pakitsoq. Sections containing ice from every distinct climatic interval during Termination I, including Last Glacial Maximum, Bolling/Allerod, Younger Dryas and the early Holocene, are identified. In the early Holocene, we find evidence for climatic fluctuations similar to signals found in deep ice cores...

  17. Spectral Profiler Probe for In Situ Snow Grain Size and Composition Stratigraphy

    Science.gov (United States)

    Berisford, Daniel F.; Molotch, Noah P.; Painter, Thomas

    2012-01-01

    An ultimate goal of the climate change, snow science, and hydrology communities is to measure snow water equivalent (SWE) from satellite measurements. Seasonal SWE is highly sensitive to climate change and provides fresh water for much of the world population. Snowmelt from mountainous regions represents the dominant water source for 60 million people in the United States and over one billion people globally. Determination of snow grain sizes comprising mountain snowpack is critical for predicting snow meltwater runoff, understanding physical properties and radiation balance, and providing necessary input for interpreting satellite measurements. Both microwave emission and radar backscatter from the snow are dominated by the snow grain size stratigraphy. As a result, retrieval algorithms for measuring snow water equivalents from orbiting satellites is largely hindered by inadequate knowledge of grain size.

  18. Becoming Inclusive: A Code of Conduct for Inclusion and Diversity.

    Science.gov (United States)

    Schmidt, Bonnie J; MacWilliams, Brent R; Neal-Boylan, Leslie

    There are increasing concerns about exclusionary behaviors and lack of diversity in the nursing profession. Exclusionary behaviors, which may include incivility, bullying, and workplace violence, discriminate and isolate individuals and groups who are different, whereas inclusive behaviors encourage diversity. To address inclusion and diversity in nursing, this article offers a code of conduct. This code of conduct builds on existing nursing codes of ethics and applies to nursing students and nurses in both educational and practice settings. Inclusive behaviors that are demonstrated in nurses' relationships with patients, colleagues, the profession, and society are described. This code of conduct provides a basis for measureable change, empowerment, and unification of the profession. Recommendations, implications, and a pledge to action are discussed. Copyright © 2016 Elsevier Inc. All rights reserved.

  19. Upper mantle fluids evolution, diamond formation, and mantle metasomatism

    Science.gov (United States)

    Huang, F.; Sverjensky, D. A.

    2017-12-01

    During mantle metasomatism, fluid-rock interactions in the mantle modify wall-rock compositions. Previous studies usually either investigated mineral compositions in xenoliths and xenocrysts brought up by magmas, or examined fluid compositions preserved in fluid inclusions in diamonds. However, a key study of Panda diamonds analysed both mineral and fluid inclusions in the diamonds [1] which we used to develop a quantitative characterization of mantle metasomatic processes. In the present study, we used an extended Deep Earth Water model [2] to simulate fluid-rock interactions at upper mantle conditions, and examine the fluids and mineral assemblages together simultaneously. Three types of end-member fluids in the Panda diamond fluid inclusions include saline, rich in Na+K+Cl; silicic, rich in Si+Al; and carbonatitic, rich in Ca+Mg+Fe [1, 3]. We used the carbonatitic end-member to represent fluid from a subducting slab reacting with an excess of peridotite + some saline fluid in the host environment. During simultaneous fluid mixing and reaction with the host rock, the logfO2 increased by about 1.6 units, and the pH increased by 0.7 units. The final minerals were olivine, garnet and diamond. The Mg# of olivine decreased from 0.92 to 0.85. Garnet precipitated at an early stage, and its Mg# also decreased with reaction progress, in agreement with the solid inclusions in the Panda diamonds. Phlogopite precipitated as an intermediate mineral and then disappeared. The aqueous Ca, Mg, Fe, Si and Al concentrations all increased, while Na, K, and Cl concentrations decreased during the reaction, consistent with trends in the fluid inclusion compositions. Our study demonstrates that fluids coming from subducting slabs could trigger mantle metasomatism, influence the compositions of sub-lithospherc cratonic mantle, precipitate diamonds, and change the oxygen fugacity and pH of the upper mantle fluids. [1] Tomlinson et al. EPSL (2006); [2] Sverjensky, DA et al., GCA (2014

  20. Stratigraphy of Pyroclastic Deposits of EL Aguajito Caldera, Baja California Sur, MÉXICO

    Science.gov (United States)

    Osorio Ocampo, L. S.; Macias, J. L.; García Sánchez, L.; Pola, A.; Saucedo, R.; Sánchez, J. M.; Avellán, D. R.; Cardona, S.; Reyes-Agustín, G.; Arce, J. L.

    2015-12-01

    El Aguajito caldera is located in the State of Baja California Sur, it comprises an area of 450 km2 and sits within the Santa Rosalía Basin which is controlled by NE-SW extensional structures and the NW-SE Cimarron Fault that transects the caldera structure. The oldest rocks are ~90 Ma granodiorites covered by an Oligocene-Miocene volcano-sedimentary sequence, the Miocene Santa Lucia Formation and La Esperanza basalt. Pliocene volcanism is represented by La Reforma caldera, El Aguajito caldera, and the Tres Vírgenes Volcanic complex. This study focuses on the cartography and stratigraphy of area in order to understand the evolution of the volcanic system. The stratigraphy from base to top consists of a series of shallow marine sediments (fossiliferous sandstones) covered by a thick sequence of ignimbrites and pyroclastic flows interbedded with volcaniclastic deposits (Gloria and El Infierno Formations). On top of these deposits is El Aguajito caldera, it consists of a 2 m thick pumice fallout followed by an ignimbrite with three transitional lithofacies: a ≤30-m thick light-pink pyroclastic flow enriched in pumice at the base that gradually becomes enrich in lithics towards the top with the occurrence of degasing pipes. On top rests a 15 m-thick light-purple ignimbrite slightly welded with fiammes and a sequence of pumiceous pyroclastic flows and fallouts. These deposits have been associate to the caldera formation with a collapse diameter of ~8 km marked by rhyolitic domes exposed along a ring collapse crowned the sequence as well as NW-SE aligned rhyolitic domes parallel to the seashore. This cartography allowed to present a preliminary new geological map with four stratigraphic units recognized so far, that were emplaced under subaerial conditions beginning with a Plinian column followed by the emplacement of El Aguajito ignimbrite with its subsequent caldera collapse and finally the extrusion of resurgent domes.

  1. Stratigraphy and depositional environments of Catahoula Formation sandstones and associated facies in south-central Mississippi

    Energy Technology Data Exchange (ETDEWEB)

    Cameron, C.P. (Univ. of Southern Mississippi, Hattiesburg (USA)); Day, L.A. (Geraghty and Miller, Baton Rouge, LA (USA))

    1990-09-01

    Surface and subsurface studies of the Catahoula Formation in a seven county area of south-central Mississippi have revealed major problems and misconceptions regarding Neogene stratigraphy and geological mapping in this part of the Gulf basin. The results of these investigations show that the traditional stratigraphic subdivisions of the up-dip Neogene section in Mississippi are invalid, and that the fundamental criteria for defining rock stratigraphic units at the formation rank are nonexistent. Although the base of the Neogene section is reasonably well defined by virtue of its relatively continuous contact with the Bucatunna Formation (Oligocene Vicksburg Group), a mappable bounding sequence above the Catahoula-Bucatunna Formation contact does not exist in the study area. An overall fine-grained interval above the Catahoula Formation appears to wedge out before reaching outcrop. Hence, differentiation between up-dip sandy gravels of the Catahoula and similar facies of the Citronelle Formation is difficult. Further complicating the problem of stratigraphic unit discrimination is the discovery of sandy gravels within the Hattiesburg Formation interval. A subsurface analysis in this study area revealed that the Catahoula Formation, as defined by Day, attains a thickness of 625 ft and has a rough three-tiered stratigraphy: (a) a basal unit composed of sands and subordinate fine-grained facies; (b) a relatively fine-grained middle unit composed of silts and clays with recurrent, discontinuous, sand bodies; and (c) an upper unit composed largely of sand and gravels. This study confirmed that most of these sediments are the product of fluvial channel and associated floodplain deposition. However, in the basal unit deltaic facies appear to be preserved on outcrop in Smith County and perhaps in a mild structural depression in the southwest portion of the study area.

  2. Precise Dating of Flood-Plain Stratigraphy Using Changes in Tree-Ring Anatomy Following Burial

    Science.gov (United States)

    Friedman, J. M.; Shafroth, P. B.; Vincent, K. R.; Scott, M. L.; Auble, G. T.

    2001-12-01

    Determination of sediment deposition rates from stratigraphy is typically limited by a scarcity of chronological information. We present a method for precise dating of sedimentary beds based on the change in anatomy of tree rings upon burial. When stems of tamarisk (Tamarix ramosissima)and sandbar willow (Salix exigua) are buried, subsequent annual rings in the buried portions become narrower and vessels within the rings become larger. Observation of these changes can be combined with tree ring counts to determine the year of deposition of sedimentary beds that are at least 10 cm thick. Using a backhoe we dug trenches across the flood plain at three locations along the arroyo of the Rio Puerco, New Mexico. At each cross section we prepared a detailed stratigraphic description and excavated several tamarisks to depths as great as 5 meters. From each excavated tree we cut and sanded 10-50 slabs for tree-ring analysis. We cross-dated slabs within and between plants and used the burial signature in the tree rings to date all sedimentary beds in the stratigraphic profile near each plant. We then used the trench stratigraphy to convert depths of sediment deposition around individual trees to areas of deposition in the cross section. In the lower Rio Puerco introduction of tamarisk in 1926 occurred just prior to the beginning of channel narrowing and arroyo filling. Thus the tamarisks record a process of channel change to which they may have contributed. Aggradation has not been synchronous along the lower arroyo. For example, near Highway 6 and Belen, the flood plain has aggraded more than 2 m since 1970, while there has been little aggradation downstream at Bernardo. Much of the sediment deposition in levies at Highway 6 occurred during a flood in 1988. Future work will document longitudinal variation in the arroyo so that we can convert areas of sediment deposition in cross sections to volumes in the arroyo.

  3. Shallow Stratigraphy of Valsequillo Basin From Electrical Resistivity Soundings, Gravity and Magnetics

    Science.gov (United States)

    Trigo-Huesca, A.; Tellez-Garcia, E.; Ortega-Nieto, A.; Mayo-Reyes, J.; Lopez-Aguirre, D.; Perez-Cruz, L.; Gogichaishvili, A.; Urrutia-Fucugauchi, J.

    2008-05-01

    The recent study by Gonzalez et al. (2006) on the occurrence of apparent human and animal footprints on the Xalnene ash that outcrops in the Valsequillo Basin has attracted attention to the region of central Mexico, within the context of the early human migration in the Americas. OSL dating of interlayered baked lake sediments gave dates around 40 ka, supporting an early human presence in central Mexico. Xalnene ash was dated by Renne et al. (2005) giving an Ar/Ar date of 1.3 Ma, questioning a human origin for the footprints. Paleomagnetic and rock magnetic data on the Xalnene ash and Toluquilla volcano lavas have been discussed in terms of the correlation to the C1r.2r chron (about 1.07 to 1.77 Ma) and the old Ar/Ar date or the Laschamp geomagnetic excursion and the younger OSL dates. These studies have highlighted the interest on the stratigraphy of the volcanic and sedimentary sequence of the Valsequillo Basin. Here, we present initial results from electrical resistivity soundings, gravity and magnetics in the areas covered by the Xalnene ash and the nearby Toluquilla volcano. The geophysical models are interpreted in terms of the shallow stratigraphy of the volcanic and lacustrine sediment units. The electrical resistivity soundings identify several layers in the shallow 8-20 m, beneath the area with the apparent footprints and the slope of Toluquilla volcano, and permit imaging of these shallow units. Geophysical models for the Toluquilla volcano and surrounding zones allow deeper investigation and incorporate several units mapped in past studies, particularly the Xalnene ash, upper/lower lacustrine sequences, lahars, Caulapan tuffs and sediments, and Balsas Group sedimentary rocks.

  4. Linking process, morphology, and stratigraphy in the Ganges-Brahmaputra-Meghna delta

    Science.gov (United States)

    Wilson, C.; Goodbred, S. L., Jr.; Sincavage, R.; Steckler, M. S.; Pickering, J.

    2015-12-01

    The Ganges-Brahmaputra-Meghna delta (GBMD) is characterized as a composite system with an upland fluvial fan delta, a lowland, backwater-reach delta, a downdrift tidal delta plain, and an offshore subaqueous-delta, reflecting the respective dominance of fluvial, tidal, and marine processes. Topographic transitions, coupled with surface morphology and underlying stratigraphy define the temporally and spatially integrated patterns of river behavior and sediment dispersal that characterize the delta system. These play important roles in the scale of natural hazards, such as flooding and storm surges, affecting the 150 million inhabitants of the GBMD. Within the upland fan delta, aggradation of mobile braided channels within the active rivers support the wide-scale distribution of bed- and suspended-load sands that constitute nearly the entire underlying architecture of upper GBMD stratigraphy. Finer silt-dominated facies form on the floodplain from overbank deposition during waning stages of flow; however preservation is very low and localized because of the persistent lateral migration of braided channels. A differentiation in stream morphology and channel behavior is associated with a sharp decrease in stream gradient, channel avulsion and abandonment, and the transition across the backwater. Deposition and preservation of fine-grained mud and organic-rich successions are concentrated within broad interdistributary basins of the lowland fluvial plain or within tectonically subsiding Sylhet Basin. While ~15% of the 1 x 109 t yr-1 sediment load carried by the rivers is advected along shore and inland via tidal activity, a rapidly prograding subaqueous clinoform and the adjacent Swatch of No Ground canyon system offshore receive ~50% of the modern sediment load. The overall stability of the GBMD landform, relative to many deltas, reflects the efficient, widespread dispersal of sediment by the large monsoon discharge and high-energy tides that affect this region

  5. Social inclusion and mental health.

    Science.gov (United States)

    Cobigo, Virginie; Stuart, Heather

    2010-09-01

    Recent research on approaches to improving social inclusion for people with mental disabilities is reviewed. We describe four approaches (or tools) that can be used to improve social inclusion for people with mental disabilities: legislation, community-based supports and services, antistigma/antidiscrimination initiatives, and system monitoring and evaluation. While legislative solutions are the most prevalent, and provide an important framework to support social inclusion, research shows that their full implementation remains problematic. Community-based supports and services that are person-centered and recovery-oriented hold considerable promise, but they are not widely available nor have they been widely evaluated. Antistigma and antidiscrimination strategies are gaining in popularity and offer important avenues for eliminating social barriers and promoting adequate and equitable access to care. Finally, in the context of the current human rights and evidence-based health paradigms, systematic evidence will be needed to support efforts to promote social inclusion for people with mental disabilities, highlight social inequities, and develop best practice approaches. Tools that promote social inclusion of persons with mental disabilities are available, though not yet implemented in a way to fully realize the goals of current disability discourse.

  6. Demands from the school inclusion

    Directory of Open Access Journals (Sweden)

    Selma Norberto Matos

    2014-04-01

    Full Text Available From the implementation of public policies on school inclusion, mainly those directed to the target audience of special education, the number of students with special educational needs in common classes has increased. This fact has helped to compose the picture in schools where the limitations and contradictions of the Brazilian educational system have appeared. Educational actors and authors are challenged to build knowledge able of responding to demands of daily school, concerning living and learning in diversity. Whereas this inclusive process is new in the schools, the study aimed to analyze the demands of teachers from the school inclusion. The research was qualitative and exploratory, and six teachers, their students with special educational needs and three professionals in the Nucleus of Inclusive Education from the Municipal Department of Education took in it. Technique of participant observation, field diary, semi-structured interview and questionnaire were used for data collection, while analysis of content was used for discussion of the data. The results indicate that there are achievements and contradictions in the reality of schools that themselves propose inclusive; advances and limitations resulting from the municipal politics; that the model of performance of the group of special education, in the context analyzed, may be revised or expanded; and that the teachers has demands with regard to public policy, training, and the psychologist.

  7. The Sociology of Social Inclusion

    Directory of Open Access Journals (Sweden)

    Dan Allman

    2013-01-01

    Full Text Available This article looks at social inclusion from a sociological perspective. It argues that sociology complements biological and other natural order explanations of social stratification. The article interrogates a variety of forms of social integration, including ostracism within 5th century b.c. Greece, 19th-century solidarism, and Goffman’s mid-20th-century work on stigma. It does so to demonstrate how in each of these contexts, social inclusion and exclusion can function as apparati that problematize people on the margins, and by extension, contribute to their governance and control. The article proposes that sociology provides a valuable orientation from which to consider social inclusion because it illuminates how social integration maintains and manages the ways in which people move about and through their socially stratified worlds.

  8. Genesis of diamond inclusions: An integrated cathodoluminescence (CL) and Electron backscatter diffraction (EBSD) study on eclogitic and peridotitic inclusions and their diamond host.

    Science.gov (United States)

    van den Heuvel, Quint; Matveev, Sergei; Drury, Martyn; Gress, Michael; Chinn, Ingrid; Davies, Gareth

    2017-04-01

    Diamond inclusions are potentially fundamental to understanding the formation conditions of diamond and the volatile cycles in the deep mantle. In order to fully understand the implications of the compositional information recorded by inclusions it is vital to know whether the inclusions are proto-, syn-, or epigenetic and the extent to which they have equilibrated with diamond forming fluids. In previous studies, the widespread assumption was made that the majority of diamond inclusions are syngenetic, based upon observation of cubo-octahedral morphology imposed on the inclusions. Recent work has reported the crystallographic relationship between inclusions and the host diamond to be highly complex and the lack of crystallographic relationships between inclusions and diamonds has led some to question the significance of imposed cubo-octahedral morphology. This study presents an integrated EBSD and CL study of 9 diamonds containing 20 pyropes, 2 diopsides, 1 forsterite and 1 rutile from the Jwaneng and Letlhakane kimberlite clusters, Botswana. A new method was developed to analyze the crystallographic orientation of the host diamond and the inclusions with EBSD. Diamonds plates were sequentially polished to expose inclusions at different levels in the diamond. CL imaging at different depths was performed in order to produce a 3D view of diamond growth zones around the inclusions. Standard diamond polishing techniques proved too aggressive for silicate inclusions as they were damaged to such a degree that EBSD measurements on the inclusions were impossible. The inclusions were milled with a Ga+ focused ion beam (FIB) at a 12° angle to clean the surface for EBSD measurements. Of the 24 inclusions, 9 have an imposed cubo-octahedral morphology. Of these inclusions, 6 have faces orientated parallel to diamond growth zones and/or appear to have nucleated on a diamond growth surface, implying syngenesis. In contrast, other diamonds record resorption events such that

  9. Process fluid cooling system

    International Nuclear Information System (INIS)

    Farquhar, N.G.; Schwab, J.A.

    1977-01-01

    A system of heat exchangers is disclosed for cooling process fluids. The system is particularly applicable to cooling steam generator blowdown fluid in a nuclear plant prior to chemical purification of the fluid in which it minimizes the potential of boiling of the plant cooling water which cools the blowdown fluid

  10. Fluid mechanics in fluids at rest.

    Science.gov (United States)

    Brenner, Howard

    2012-07-01

    Using readily available experimental thermophoretic particle-velocity data it is shown, contrary to current teachings, that for the case of compressible flows independent dye- and particle-tracer velocity measurements of the local fluid velocity at a point in a flowing fluid do not generally result in the same fluid velocity measure. Rather, tracer-velocity equality holds only for incompressible flows. For compressible fluids, each type of tracer is shown to monitor a fundamentally different fluid velocity, with (i) a dye (or any other such molecular-tagging scheme) measuring the fluid's mass velocity v appearing in the continuity equation and (ii) a small, physicochemically and thermally inert, macroscopic (i.e., non-Brownian), solid particle measuring the fluid's volume velocity v(v). The term "compressibility" as used here includes not only pressure effects on density, but also temperature effects thereon. (For example, owing to a liquid's generally nonzero isobaric coefficient of thermal expansion, nonisothermal liquid flows are to be regarded as compressible despite the general perception of liquids as being incompressible.) Recognition of the fact that two independent fluid velocities, mass- and volume-based, are formally required to model continuum fluid behavior impacts on the foundations of contemporary (monovelocity) fluid mechanics. Included therein are the Navier-Stokes-Fourier equations, which are now seen to apply only to incompressible fluids (a fact well-known, empirically, to experimental gas kineticists). The findings of a difference in tracer velocities heralds the introduction into fluid mechanics of a general bipartite theory of fluid mechanics, bivelocity hydrodynamics [Brenner, Int. J. Eng. Sci. 54, 67 (2012)], differing from conventional hydrodynamics in situations entailing compressible flows and reducing to conventional hydrodynamics when the flow is incompressible, while being applicable to both liquids and gases.

  11. Videotapes and Movies on Fluid Dynamics and Fluid Machines

    OpenAIRE

    Carr, Bobbie; Young, Virginia E.

    1996-01-01

    Chapter 17 of Handbook of Fluid Dynamics and Fluid Machinery: Experimental and Computational Fluid Dynamics, Volume 11. A list of videorecordings and 16mm motion pictures about Fluid Dynamics and Fluid Machines.

  12. The Inclusion of Music/the Music of Inclusion

    Science.gov (United States)

    Lubet, Alex

    2009-01-01

    The intention of this paper is to situate music within inclusive education. Intersections of music--widely regarded as a "talent" or hyperability--and disability provide unique perspectives on social organisation in general and human valuation in particular. Music is a ubiquitous and an essential component of learning beginning in infancy.…

  13. Doing Research Inclusively: Bridges to Multiple Possibilities in Inclusive Research

    Science.gov (United States)

    Nind, Melanie; Vinha, Hilra

    2014-01-01

    This article reports on a study of how people do research that matters to people with learning disabilities and that involves them and their views and experiences. The study was an attempt to bring together people doing inclusive research so that, collectively, we could take stock of our practices. This would add to the individual reports and…

  14. Inclusiveness program - a SWOT analysis

    Science.gov (United States)

    Dósa, M.; Szegő, K.

    2017-09-01

    The Inclusiveness Program was created with the aim to integrate currently under-represented countries into the mainstream of European planetary research. Main stages of the working plan include setting up a database containing all the research institutes and universities where astronomical or geophysical research is carried out. It is necessary to identify their problems and needs. Challenging part of the project is to find exact means that help their work in a sustainable way. Strengths, weaknesses, opportunities and threats of the program were identified based on feedback from the inclusiveness community. Our conclusions, further suggestions are presented.

  15. Paleontology and stratigraphy of the Upper Triassic Kamishak Formation in the Puale Bay-Cape Kekurnoi-Alinchak Bay area, Karluk C-4 and C-5 quadrangle

    Data.gov (United States)

    Department of the Interior — This report summarizes the paleontological character and stratigraphy of the Kamishak Formation in the Puale Bay–Cape Kekurnoi–Alinchak Bay area, Karluk C-4 and C-5...

  16. Social Inclusion and Integrative Practices

    Directory of Open Access Journals (Sweden)

    David Cappo

    2014-06-01

    Full Text Available With the passage of time valuable lessons have been learnt about both effective practices for program and system integration and the sizable barriers, including the challenges in sustaining constructive integration. This paper is a reflection on sustainable integrative practices and is grounded in the direct experience of one of the authors, who held the post of the South Australian Social Inclusion Commissioner. We reflect upon the structure and mechanism of the South Australian Social Inclusion Initiative (2002–2011 as well as using a case study of a successful integrative program of the Social Inclusion Initiative, a program in South Australia’s School Retention Action Plan 2004 Making the Connections (South Australian Social Inclusion Board, 2004 that was implemented to improve school retention. The case study draws out salient factors of clear rationale, coordination, collaboration, communication, team work and trust as skills and ingredients to bring about integration in policy and programs. While the integration literature affirms that these ingredients are primary skills for the development of an integrative framework, we also assert that they are not enough for successful and sustained integration. Absent from much of the literature is a discussion about the use of power and the manner in which horizontal integrative work occurs. We take up this theme to draw out some implications for analysis of sustainable integrative practices.

  17. How Bureaucracy Promotes Inclusive Organizing

    DEFF Research Database (Denmark)

    Holck, Lotte

    Diversity literature in general and Feminist in particular have long promoted alternatives to bureaucracy on the premise that this form of governance is far from gender- and race-neutral, and that inclusive organizing necessitate a flatter, decentralized and more ‘organic’ set-up (Ferguson 1984...

  18. Inclusion body myositis. Clinical aspects

    NARCIS (Netherlands)

    Cox, Fieke Maria Elisabeth

    2014-01-01

    Sporadische inclusion body myositis (IBM) is een van de meest voor voorkomende verworven spierziekte die ontstaat na het 50e levensjaar. In dit proefschrift worden de klinische aspecten van sporadische IBM beschreven. Uit de studie met betrekking tot het natuurlijk beloop blijkt dat de ziekte niet

  19. Nonlocal quasilinear damped differential inclusions

    Directory of Open Access Journals (Sweden)

    Mouffak Benchohra

    2002-01-01

    Full Text Available In this paper we investigate the existence of mild solutions to second order initial value problems for a class of damped differential inclusions with nonlocal conditions. By using suitable fixed point theorems, we study the case when the multivalued map has convex and nonconvex values.

  20. Early Childhood Inclusion in Australia

    Science.gov (United States)

    Kemp, Coral R.

    2016-01-01

    From the introduction of early intervention services in Australian in the mid-1970s, the families of children with intellectual and multiple disabilities have been encouraged to enroll their children in local preschools and childcare centers. Children with disabilities have also accessed a range of alternatives to full inclusion, such as reverse…

  1. Teacher preparedness for inclusive education

    African Journals Online (AJOL)

    lynette

    Since the report of the National Department of Education, “Quality. Education for All” was published in 1997, it has became evident that inclusive education is going to be the way forward in special (and regular) education. Both the Consultative Paper on Special Educa- tion (30 August 1999) and the Draft White Paper on ...

  2. Inclusive Education and the Arts

    Science.gov (United States)

    Allan, Julie

    2014-01-01

    This paper addresses the troubled, problematic and contested field of inclusive education, characterised by antagonisms between so-called inclusionists and special educationists; frustration, particularly among disability activists caused by the abstraction of the social model of disability and the expansion of the special educational needs…

  3. Inclusion

    DEFF Research Database (Denmark)

    Jørgensen, Stine Kaplan

    2017-01-01

    Paperet sætter fokus på inklusion i en dans sammenhæng, med særligt fokus på mobning. Der tages udgangspunkt i et fællesskabsorienteret mobbesyn, der udpeger særlige opmærksomhedspunkter til såvel forebyggelse som intervention....

  4. INCLUSIVE CULTURE IN PRE-SCHOOL INSTITUTIONS

    Directory of Open Access Journals (Sweden)

    Irena NOVACHEVSKA

    2011-04-01

    Full Text Available Inclusive education is a rational concept that refers to the overall and long-term transformation of institutional systems in society, especially in education. Along with the transformation, a number of important and unresolved issues still appear in both theory and practice, as the duty of pre-school institutions and schools is to educate every student in the mainstream education system. One of the most important aspects of inclusion is the inclusive culture. Regardless of the good inclusive policy and practice, one cannot talk about successful inclusion without a properly developed inclusive institutional culture.This paper is a contribution to the research considering the development of inclusive culture in three preschool institutions. It is based on the thinking and attitudes of the pre­school staff toward the necessity of developing and nurturing an inclusive culture. Successful inclusion of pupils with special needs in the mainstream school system cannot be conceived without an inclusive culture.

  5. Primordial Compositions of Refractory Inclusions

    Energy Technology Data Exchange (ETDEWEB)

    Grossman, L; Simon, S B; Rai, V K; Thiemens, M H; Hutcheon, I D; Williams, R W; Galy, A; Ding, T; Fedkin, A V; Clayton, R N; Mayeda, T K

    2008-02-20

    Bulk chemical and oxygen, magnesium and silicon isotopic compositions were measured for each of 17 Types A and B refractory inclusions from CV3 chondrites. After bulk chemical compositions were corrected for non-representative sampling in the laboratory, the Mg and Si isotopic compositions of each inclusion were used to calculate its original chemical composition assuming that the heavy-isotope enrichments of these elements are due to Rayleigh fractionation that accompanied their evaporation from CMAS liquids. The resulting pre-evaporation chemical compositions are consistent with those predicted by equilibrium thermodynamic calculations for high-temperature nebular condensates but only if different inclusions condensed from nebular regions that ranged in total pressure from 10{sup -6} to 10{sup -1} bar, regardless of whether they formed in a system of solar composition or in one enriched in OC dust relative to gas by a factor of ten relative to solar composition. This is similar to the range of total pressures predicted by dynamic models of the solar nebula for regions whose temperatures are in the range of silicate condensation temperatures. Alternatively, if departure from equilibrium condensation and/or non-representative sampling of condensates in the nebula occurred, the inferred range of total pressure could be smaller. Simple kinetic modeling of evaporation successfully reproduces observed chemical compositions of most inclusions from their inferred pre-evaporation compositions, suggesting that closed-system isotopic exchange processes did not have a significant effect on their isotopic compositions. Comparison of pre-evaporation compositions with observed ones indicates that 80% of the enrichment in refractory CaO + Al{sub 2}O{sub 3} relative to more volatile MgO + SiO{sub 2} is due to initial condensation and 20% due to subsequent evaporation for both Type A and Type B inclusions.

  6. Inclusive teaching strategies - dimensions and agendas

    DEFF Research Database (Denmark)

    Molbæk, Mette

    2017-01-01

    will contribute to an enrichment of the two research fields and give teachers and researchers new opportunities for developing more inclusive schools. Based on research focused on teaching strategies that support students’ opportunities for learning, four dimensions of inclusive teaching strategies are presented...... those teachers working with inclusion can be supported with more tangible and meaningful ways of understanding and developing inclusive classrooms. This article argues that seeing research in inclusion in close connection with research in effective teaching strategies and classroom management...

  7. Inclusion control in high-performance steels

    International Nuclear Information System (INIS)

    Holappa, L.E.K.; Helle, A.S.

    1995-01-01

    Progress of clean steel production, fundamentals of oxide and sulphide inclusions as well as inclusion morphology in normal and calcium treated steels are described. Effects of cleanliness and inclusion control on steel properties are discussed. In many damaging constructional and engineering applications the nonmetallic inclusions have a quite decisive role in steel performance. An example of combination of good mechanical properties and superior machinability by applying inclusion control is presented. (author)

  8. FOREWORD Fluid Mechanics and Fluid Power (FMFP)

    Indian Academy of Sciences (India)

    This section of the Special Issue carries selected articles from the Fluid Mechanics and Fluid. Power Conference held during 12–14 December 2013 at the National Institute of Technology,. Hamirpur (HP). The section includes three review articles and nine original research articles. These were selected on the basis of their ...

  9. Late Pleistocene Holocene stratigraphy and radiocarbon dating of La Malinche volcano, Central Mexico

    Science.gov (United States)

    Castro-Govea, Renato; Siebe, Claus

    2007-04-01

    Previous studies of La Malinche identified and radiocarbon dated several volcanic layers, the youngest of which yielded an age of ca. 7.5 ka. An additional ash fallout layer that crops out at high altitudes was considered the most recent deposit, with an estimated age of 6 ka. In the present work 38 new radiocarbon ages are presented. From these, several date the young ash fallout layer and lie around 3.1 ka. With the aid of these dates a new and comprehensive stratigraphy documenting the Late Pleistocene-Holocene eruptive history of La Malinche is presented. The stratigraphy indicates two main stages of volcanic activity: Pre-Malinche and Malinche. The first undoubtedly comprises the major part of the eruptive history, but its deposits are largely covered by the products of the latter stage, on which this study is focused. The Malinche stage was subdivided into three eruptive periods. Period 1 started with the emplacement of the Huamantla Pumice more than 45 ka ago. This deposit consists of a thick pumice fallout overlain by pyroclastic flow deposits. Subsequently, several episodes of construction and collapse of summit domes occurred. The oldest dome was dated at ca. 45 ka. Period 2 started 21.5 ka ago with the Malinche Pumice I, a widespread pumice fallout covering the entire slopes of the volcano. Pyroclastic flows and lahars related to this eruption were channeled along deep barrancas and reached considerable distances. Deposits produced by partial sector collapse and dated at ca. 20.9 ka, and a pumice-and-ash flow deposit dated at 15.9 ka were also generated during this period. The last period started with the eruption of the Malinche Pumice II, a distinctive fallout deposit overlain by ash flow deposits on the NE slope of the volcano. The age of this pumice layer is estimated between 12 and 9 ka. Formation of block-and-ash flows, lahars and pumice-and-ash flows followed during this period, and peaked in a most intensive episode that was dated at 7.5 ka

  10. Fluid/structure interaction in BERDYNE (Level 4)

    International Nuclear Information System (INIS)

    Fox, M.J.H.

    1988-02-01

    A fluid-structure interaction capability has been developed for Level 4 of the finite element dynamics code BERDYNE, as part of the BERSAFE structural analysis system. This permits analysis of small amplitude free or forced vibration of systems comprising elastic structural components and inviscid volumes of possibly compressible fluid. Free fluid surfaces under the influence of gravity may be present. The formulation chosen uses the rigid walled fluid modes, calculated in a preliminary stage, as a basis for description of the coupled system, providing symmetric system matrices for which efficient solution procedures are available. The inclusion of the fluid modal variables within the system matrices is carried out through the use of the BERDYNE 'substructuring' feature, which allows the inclusion of very general 'super-elements' among the normal structural elements. The program also has a seismic analysis capability, used for the analysis of fluid-structure systems subjected to a specified support acceleration time history. In this case analysis is carried out in terms of relative structural motions, but absolute fluid pressures. Application of the BERDYNE fluid/structure interaction capability to some simple test cases produced results in good agreement with results obtained by analytic or independent numerical techniques. Full instructions on the use of the facility will be included in the BERDYNE Level 4 documentation. Interim documentation for the pre-release version is available from the author. (author)

  11. Fluid involvement in normal faulting

    Science.gov (United States)

    Sibson, Richard H.

    2000-04-01

    Evidence of fluid interaction with normal faults comes from their varied role as flow barriers or conduits in hydrocarbon basins and as hosting structures for hydrothermal mineralisation, and from fault-rock assemblages in exhumed footwalls of steep active normal faults and metamorphic core complexes. These last suggest involvement of predominantly aqueous fluids over a broad depth range, with implications for fault shear resistance and the mechanics of normal fault reactivation. A general downwards progression in fault rock assemblages (high-level breccia-gouge (often clay-rich) → cataclasites → phyllonites → mylonite → mylonitic gneiss with the onset of greenschist phyllonites occurring near the base of the seismogenic crust) is inferred for normal fault zones developed in quartzo-feldspathic continental crust. Fluid inclusion studies in hydrothermal veining from some footwall assemblages suggest a transition from hydrostatic to suprahydrostatic fluid pressures over the depth range 3-5 km, with some evidence for near-lithostatic to hydrostatic pressure cycling towards the base of the seismogenic zone in the phyllonitic assemblages. Development of fault-fracture meshes through mixed-mode brittle failure in rock-masses with strong competence layering is promoted by low effective stress in the absence of thoroughgoing cohesionless faults that are favourably oriented for reactivation. Meshes may develop around normal faults in the near-surface under hydrostatic fluid pressures to depths determined by rock tensile strength, and at greater depths in overpressured portions of normal fault zones and at stress heterogeneities, especially dilational jogs. Overpressures localised within developing normal fault zones also determine the extent to which they may reutilise existing discontinuities (for example, low-angle thrust faults). Brittle failure mode plots demonstrate that reactivation of existing low-angle faults under vertical σ1 trajectories is only likely if

  12. Effect of Mg Addition on the Refinement and Homogenized Distribution of Inclusions in Steel with Different Al Contents

    Science.gov (United States)

    Wang, Linzhu; Yang, Shufeng; Li, Jingshe; Zhang, Shuo; Ju, Jiantao

    2017-04-01

    To investigate the effect of Mg addition on the refinement and homogenized distribution of inclusions, deoxidized experiments with different amounts of aluminum and magnesium addition were carried out at 1873 K (1600 °C) under the condition of no fluid flow. The size distribution of three-dimensional inclusions obtained by applying the modified Schwartz-Saltykov transformation from the observed planar size distribution, and degree of homogeneity in inclusion dispersion quantified by measuring the inter-surface distance of inclusions, were studied as a function of the amount of Mg addition and holding time. The nucleation and growth of inclusions based on homogeneous nucleation theory and Ostwald ripening were discussed with the consideration of supersaturation degree and interfacial energy between molten steel and inclusions. The average attractive force acted on inclusions in experimental steels was estimated according to Paunov's theory. The results showed that in addition to increasing the Mg addition, increasing the oxygen activity at an early stage of deoxidation and lowering the dissolved oxygen content are conductive to the increase of nucleation rate as well as to the refinement of inclusions Moreover, it was found that the degree of homogeneity in inclusion dispersion decreases with an increase of the attractive force acted on inclusions, which is largely dependent on the inclusion composition and volume fraction of inclusions.

  13. Hydrothermal zebra dolomite in the Great Basin, Nevada--attributes and relation to Paleozoic stratigraphy, tectonics, and ore deposits

    Science.gov (United States)

    Diehl, S.F.; Hofstra, A.H.; Koenig, A.E.; Emsbo, P.; Christiansen, W.; Johnson, Chad

    2010-01-01

    In other parts of the world, previous workers have shown that sparry dolomite in carbonate rocks may be produced by the generation and movement of hot basinal brines in response to arid paleoclimates and tectonism, and that some of these brines served as the transport medium for metals fixed in Mississippi Valley-type (MVT) and sedimentary exhalative (Sedex) deposits of Zn, Pb, Ag, Au, or barite. Numerous occurrences of hydrothermal zebra dolomite (HZD), comprised of alternating layers of dark replacement and light void-filling sparry or saddle dolomite, are present in Paleozoic platform and slope carbonate rocks on the eastern side of the Great Basin physiographic province. Locally, it is associated with mineral deposits of barite, Ag-Pb-Zn, and Au. In this paper the spatial distribution of HZD occurrences, their stratigraphic position, morphological characteristics, textures and zoning, and chemical and stable isotopic compositions were determined to improve understanding of their age, origin, and relation to dolostone, ore deposits, and the tectonic evolution of the Great Basin. In northern and central Nevada, HZD is coeval and cogenetic with Late Devonian and Early Mississippian Sedex Au, Zn, and barite deposits and may be related to Late Ordovician Sedex barite deposits. In southern Nevada and southwest California, it is cogenetic with small MVT Ag-Pb-Zn deposits in rocks as young as Early Mississippian. Over Paleozoic time, the Great Basin was at equatorial paleolatitudes with episodes of arid paleoclimates. Several occurrences of HZD are crosscut by Mesozoic or Cenozoic intrusions, and some host younger pluton-related polymetallic replacement and Carlin-type gold deposits. The distribution of HZD in space (carbonate platform, margin, and slope) and stratigraphy (Late Neoproterozoic Ediacaran-Mississippian) roughly parallels that of dolostone and both are prevalent in Devonian strata. Stratabound HZD is best developed in Ediacaran and Cambrian units, whereas

  14. STUDENTS’ RESPONSES TO INCLUSIVE DESIGN

    DEFF Research Database (Denmark)

    Herriott, Richard; Geert Jensen, Birgitte

    2012-01-01

    . This technology is designed help to citizens to be 'master of his or her own life' while off-setting capability changes due declining physical ability. Welfare technology includes smarter working practices or service concepts, which frees up labor resources and it also covers robotics, telemedicine, IT solutions...... and intelligent devices. This paper will show the results of students' work with the problem of changed demographics and emerging needs in products and services. In so doing it looks at how the use of inclusive design methods affects students´work processes. This is done by the use of work diaries which provided......This paper looks at how students’ design process responds to the requirements of inclusive design. The background to the students´ brief was the concept of welfare technology. People wish to retain their customary life-style even as ageing brings with it a reduction in physical capability: loss...

  15. The HLT inclusive B triggers

    CERN Document Server

    Gligorov, Vladimir V; Williams, Michael

    2011-01-01

    The inclusive HLT strategy relies on triggering any B decay based on two signatures: a single significantly displaced, high transverse momentum track, and a significantly displaced vertex containing this track and 1-3 other tracks, with high total transverse momentum. In order to provide optimal signal efficiency and background rejection the displaced vertex selection is implemented in a novel boosted decision tree algorithm incorporating information about the experimental resolution in the boosting procedure to protect against overtraining. The performance of these triggers has been commissioned using data taken during 2011 LHCb running and is evaluated here in a data-driven manner. The HLT inclusive triggers are found to have a rejection factor of around 1000 with respect to events selected by the L0 hardware trigger and a bbar purity close to 100%.

  16. Interprofessional development in inclusive schools

    DEFF Research Database (Denmark)

    Hansen, Britt Blaabjerg; Højholdt, Andy; Arndal, Lars Stubbe

    circles (Persson, 2007). The design development was theory oriented, with our introducing theories about the different aspects of professional collaboration, co-creation and social innovation (Conger, S. 2002, Edwall et. al. 2008)).In accordance with the processes of design-based research (iteration...... required to work with these students. This paper describes the challenges [education/school] professionals (teachers and child and youth educators) face in striving to develop inclusive school practice, and how these challenges relate to differences in skills and competencies between the professions....... The knowledge for the paper was generated in a research project entitled “Interprofessional development in inclusive schools”. The project worked from a basic understanding that we need to develop preventive educational strategies for children and young people with learning difficulties and in social risk...

  17. Friendship in inclusive physical education.

    Science.gov (United States)

    Seymour, Helena; Reid, Greg; Bloom, Gordon A

    2009-07-01

    Social interaction and development of friendships between children with and without a disability are often proposed as potential outcomes of inclusive education. Physical activity specialists assert that exercise and sport environments may be conducive to social and friendship outcomes. This study investigated friendship in inclusive physical education from the perspective of students with (n = 8) and without (n = 8) physical disabilities. All participants attended a reversely integrated school and were interviewed using a semistructured, open-ended format. An adapted version of Weiss, Smith, and Theeboom's (1996) interview guide exploring perceptions of peer relationships in the sport domain was used. Four conceptual categories emerged from the analysis: development of friendship, best friend, preferred physical activities and outcomes, and dealing with disability. The results demonstrated the key characteristics of best friends and the influential role they play.

  18. Social inclusion and integrative practices

    OpenAIRE

    Cappo, David; Verity, Fiona

    2014-01-01

    With the passage of time valuable lessons have been learnt about both effective practices for program and system integration and the sizable barriers, including the challenges in sustaining constructive integration. This paper is a reflection on sustainable integrative practices and is grounded in the direct experience of one of the authors, who held the post of the South Australian Social Inclusion Commissioner. We reflect upon the structure and mechanism of the South Australian Social Inclu...

  19. Student' responses to inclusive design

    DEFF Research Database (Denmark)

    Herriott, Richard; Geert Jensen, Birgitte

    2013-01-01

    ” and “disordered”, this study visualises it and finds patterns underlying a process which is perceived to be chaotic. It provides a rough measure of the dynamics of a project in the form of the “switch between” ratio: how many changes in activity take place from the start to the finish of a project. The article...... was originally written for the DRTS 2012 conference "Articulating Design Thinking" and proposed for inclusion in a special edition of Design Issues....

  20. The Sociology of Social Inclusion

    OpenAIRE

    Dan Allman

    2013-01-01

    This article looks at social inclusion from a sociological perspective. It argues that sociology complements biological and other natural order explanations of social stratification. The article interrogates a variety of forms of social integration, including ostracism within 5th century b.c. Greece, 19th-century solidarism, and Goffman’s mid-20th-century work on stigma. It does so to demonstrate how in each of these c...

  1. Student Engagement In Inclusive Classrooms

    DEFF Research Database (Denmark)

    Rangvid, Beatrice Schindler

    There is general agreement that to thrive and learn at their best, students must be engaged. However, schools face a particular challenge to provide a suitable and engaging learning environment for SEN (special educational needs) students who are educated in general education classes. Using data......-students as for other students. This highlights the need for better inclusion initiatives aimed at strengthening engagement of SEN-students in regular classrooms....

  2. Inclusive fitness theory and eusociality

    DEFF Research Database (Denmark)

    Abbot, Patrick; Abe, Jun; Alcock, John

    2011-01-01

    Arising from M. A. Nowak, C. E. Tarnita & E. O. Wilson 466, 1057-1062 (2010); Nowak et al. reply. Nowak et al. argue that inclusive fitness theory has been of little value in explaining the natural world, and that it has led to negligible progress in explaining the evolution of eusociality. However......, we believe that their arguments are based upon a misunderstanding of evolutionary theory and a misrepresentation of the empirical literature. We will focus our comments on three general issues....

  3. Electric fluid pump

    Science.gov (United States)

    Van Dam, Jeremy Daniel; Turnquist, Norman Arnold; Raminosoa, Tsarafidy; Shah, Manoj Ramprasad; Shen, Xiaochun

    2015-09-29

    An electric machine is presented. The electric machine includes a hollow rotor; and a stator disposed within the hollow rotor, the stator defining a flow channel. The hollow rotor includes a first end portion defining a fluid inlet, a second end portion defining a fluid outlet; the fluid inlet, the fluid outlet, and the flow channel of the stator being configured to allow passage of a fluid from the fluid inlet to the fluid outlet via the flow channel; and wherein the hollow rotor is characterized by a largest cross-sectional area of hollow rotor, and wherein the flow channel is characterized by a smallest cross-sectional area of the flow channel, wherein the smallest cross-sectional area of the flow channel is at least about 25% of the largest cross-sectional area of the hollow rotor. An electric fluid pump and a power generation system are also presented.

  4. Hydraulic Brake Fluid,

    Science.gov (United States)

    A hydraulic brake fluid consisting of diethylene glycol , monoethyl ether of diethylene glycol , and castor oil has been improved as described in the patent by adding the fluid tributyl ether of orthophosphoric acid.

  5. Lectures on fluid mechanics

    CERN Document Server

    Shinbrot, Marvin

    2012-01-01

    Readable and user-friendly, this high-level introduction explores the derivation of the equations of fluid motion from statistical mechanics, classical theory, and a portion of the modern mathematical theory of viscous, incompressible fluids. 1973 edition.

  6. Pleural fluid Gram stain

    Science.gov (United States)

    Gram stain of pleural fluid ... mixing it with a violet stain (called a Gram stain). A laboratory specialist uses a microscope to ... reveals an abnormal collection of pleural fluid. The Gram stain can help identify the bacteria that might ...

  7. Quantifying small-scale spatio-temporal variability of snow stratigraphy in forests based on high-resolution snow penetrometry

    Science.gov (United States)

    Teich, M.; Hagenmuller, P.; Bebi, P.; Jenkins, M. J.; Giunta, A. D.; Schneebeli, M.

    2017-12-01

    Snow stratigraphy, the characteristic layering within a seasonal snowpack, has important implications for snow remote sensing, hydrology and avalanches. Forests modify snowpack properties through interception, wind speed reduction, and changes to the energy balance. The lack of snowpack observations in forests limits our ability to understand the evolution of snow stratigraphy and its spatio-temporal variability as a function of forest structure and to observe snowpack response to changes in forest cover. We examined the snowpack under canopies of a spruce forest in the central Rocky Mountains, USA, using the SnowMicroPen (SMP), a high resolution digital penetrometer. Weekly-repeated penetration force measurements were recorded along 10 m transects every 0.3 m in winter 2015 and bi-weekly along 20 m transects every 0.5 m in 2016 in three study plots beneath canopies of undisturbed, bark beetle-disturbed and harvested forest stands, and an open meadow. To disentangle information about layer hardness and depth variabilities, and to quantitatively compare the different SMP profiles, we applied a matching algorithm to our dataset, which combines several profiles by automatically adjusting their layer thicknesses. We linked spatial and temporal variabilities of penetration force and depth, and thus snow stratigraphy to forest and meteorological conditions. Throughout the season, snow stratigraphy was more heterogeneous in undisturbed but also beneath bark beetle-disturbed forests. In contrast, and despite remaining small diameter trees and woody debris, snow stratigraphy was rather homogenous at the harvested plot. As expected, layering at the non-forested plot varied only slightly over the small spatial extent sampled. At the open and harvested plots, persistent crusts and ice lenses were clearly present in the snowpack, while such hard layers barely occurred beneath undisturbed and disturbed canopies. Due to settling, hardness significantly increased with depth at

  8. Computational Fluid Dynamics

    International Nuclear Information System (INIS)

    Myeong, Hyeon Guk

    1999-06-01

    This book deals with computational fluid dynamics with basic and history of numerical fluid dynamics, introduction of finite volume method using one-dimensional heat conduction equation, solution of two-dimensional heat conduction equation, solution of Navier-Stokes equation, fluid with heat transport, turbulent flow and turbulent model, Navier-Stokes solution by generalized coordinate system such as coordinate conversion, conversion of basic equation, program and example of calculation, application of abnormal problem and high speed solution of numerical fluid dynamics.

  9. Stratigraphy of the Koobi Fora Formation (Pliocene and Pleistocene) in the Ileret region of northern Kenya

    Science.gov (United States)

    Gathogo, Patrick N.; Brown, Francis H.

    2006-08-01

    Exposures of Pliocene and Pleistocene deposits in the Ileret region include all eight members of the Koobi Fora Formation and represent at least 533 m of section from the base of the Lonyumun Member to the top of the Chari Mb. This thickness is more than twice that reported by earlier workers (˜260 m) and compares well with the composite section of the Koobi Fora Formation (525 m). Thus the Ileret region provides a very complete and representative outcrop of the Koobi Fora Formation. As Koobi Fora Formation member boundaries are placed at the base of specified tuffs, not all member boundaries can be recognized in the Ileret region. For this reason, the stratigraphy is described in terms of the following members (thicknesses in parentheses): Lonyumun (110 m), undifferentiated Moiti and Lokochot (104 m), Tulu Bor (54 m), Burgi (55 m), KBS (74 m), Okote (45 m), and Chari (93 m). Moreover, the boundary between the Okote Member and the KBS Member in the Ileret region is placed at a prominent caliche which must closely approximate the age of the Okote Tuff in its type section.

  10. Reconstructing depositional processes and history from reservoir stratigraphy: Englebright Lake, Yuba River, northern California

    Science.gov (United States)

    Snyder, N.P.; Wright, S.A.; Alpers, Charles N.; Flint, L.E.; Holmes, C.W.; Rubin, D.M.

    2006-01-01

    Reservoirs provide the opportunity to link watershed history with its stratigraphic record. We analyze sediment cores from a northern California reservoir in the context of hydrologic history, watershed management, and depositional processes. Observations of recent depositional patterns, sediment-transport calculations, and 137CS geochronology support a conceptual model in which the reservoir delta progrades during floods of short duration (days) and is modified during prolonged (weeks to months) drawdowns that rework topset beds and transport sand from topsets to foresets. Sediment coarser than 0.25-0.5 mm. deposits in foresets and topsets, and finer material falls out of suspension as bottomset beds. Simple hydraulic calculations indicate that fine sand (0.063-0.5 mm) is transported into the distal bottomset area only during floods. The overall stratigraphy suggests that two phases of delta building occurred in the reservoir. The first, from dam construction in 1940 to 1970, was heavily influenced by annual, prolonged >20 m drawdowns of the water level. The second, built on top of the first, reflects sedimentation from 1970 to 2002 when the influence of drawdowns was less. Sedimentation rates in the central part of the reservoir have declined ???25% since 1970, likely reflecting a combination of fewer large floods, changes in watershed management, and winnowing of stored hydraulic mining sediment. Copyright 2006 by the American Geophysical Union.

  11. Paleoecology, stratigraphy and sedimentology of the deposit of diatomite Loma Camastro, Liberia-Guanacaste

    International Nuclear Information System (INIS)

    Gamboa-Sojo, Viviana

    2013-01-01

    The use of fossil diatoms have sought to establish the evolution of the paleoecological and sedimentary processes, a section of paleolake in the warehouse Loma Camacho, Liberia-Guanacaste. The same has consisted of a volcano-sedimentary sequence of continental origin, shown as a lacustrine deposit, due to the presence of diatoms as their predominant fossil feature. The stratigraphy and sedimentology are established in detail of a portion of the formation of the Loma indicating, by this analysis, materials reworked of volcaniclastic origin and sedimentary deposits of lacustrine origin. The study has coincided to a sequence of tobitas, differentiated by their granulometry, microscopically corresponded to lodolites or claystones, with concentrations different of diatom fossils and crystals (predominantly quartz and biotic), in a clay matrix. Patterns of variation in the diatom paleocommunities are determined and have been recognized different species. General environmental conditions of paleolake are established, such as pH, productivity, solar radiation, salinity, etc. In addition, changes in diatom communities, sedimentation patterns and relations to the local and regional context were correlated setting dominant paleoenvironmental conditions for that depositional period in Loma Camastro. The main influence has been the seasonal changes in dry and rainy periods and constant volcanic activity of Volcan Rincon de la Vieja [es

  12. Holocene stratigraphy and vegetation history in the Scoresby Sund area, East Greenland

    International Nuclear Information System (INIS)

    Funder, S.

    1978-01-01

    The Holocene stratigraphy in Scoresby Sund is based on climatic change reflected by fluctuations in fjord and valley glaciers, immigration and extinction of marine molluscs, and the vegetation history recorded in pollen diagrams from five lakes. The histories are dated by C-14, and indirectly by emergence curves showing the patterns of isostatic uplift. From c. 10100-10400 to 9400 yr BP the major fjord glaciers showed oscillatory retreat with abundant moraine formation, the period of the Milne Land Moraines. The vegetation in the ice free areas was a sparse type of fell field vetetation but with thermophilous elements indicating temperatures similar to the present. From 9400 yr BP the fjord glaciers retreated rapidly in the narrow fjords, the few moraines formed are referred to the Roedefjord stages and indicate topographically conditioned stillstands. At 8000 yr BP the low arctic Betula nana imigrated into the area, and in the period until 5000 yr BP dense dwarf shrub heat grew in areas where it is now absent. In the fjords the subarctic Mytilus edulis and Pecten islandia lived, suggesting a climate warmer than the present. From c. 5000 yr BP the dense dwarf shrub heath began to disappear in the coastal areas, and a ''poor'' heat dominated by the high arctic Salix Arctica and Cassiope tetragona expanded. These two species, which are now extremely common, apparently did not grow in the area until c. 6000 yr BP. In lakes in the coastal area minerogenic sedimentation at c. 2800 yr BP, reflecting the general climatic deterioration. (author)

  13. Stratigraphy of the Vulcanodon type locality and its implications for regional correlations within the Karoo Supergroup

    Science.gov (United States)

    Viglietti, Pia A.; Barrett, Paul M.; Broderick, Tim J.; Munyikwa, Darlington; MacNiven, Rowan; Broderick, Lucy; Chapelle, Kimberley; Glynn, Dave; Edwards, Steve; Zondo, Michel; Broderick, Patricia; Choiniere, Jonah N.

    2018-01-01

    Vulcanodon karibaensis is one of the earliest-branching members of Sauropoda and a forerunner of the largest terrestrial animals ever to have lived. Its stratigraphic position has most recently been given as Toarcian (latest Early Jurassic), making it a contemporary of the northern African taxon Tazoudasaurus, but some literature suggests that it may be considerably older. This uncertainty obscures our understanding of the timing of major sauropod evolutionary events, such as the onset of the major body size increases that characterize the clade. To improve constraints on the geological age of Vulcanodon, we revisited the type locality and collected new, higher precision stratigraphic and sedimentological data. Our results show that Vulcanodon is from lower in the stratigraphy than previously documented, lying within the uppermost Forest Sandstone rather than the interbedded sandstones of the Batoka Basalt Formation. Sedimentological data suggest that the upper part of the Forest Sandstone correlates with the Clarens Formation of the main Karoo Basin, implying that Vulcanodon is likely Sinemurian-Pliensbachian in age, and potentially ∼10-15 million years (Ma) older than previously thought.

  14. STRONTIUM ISOTOPE STRATIGRAPHY AS A CONTRIBUTION FOR DATING MIOCENE SHELF CARBONATES (S. MARINO FM., NORTHERN APENNINES

    Directory of Open Access Journals (Sweden)

    CLAUDIO ARGENTINO

    2017-01-01

    Full Text Available This paper provides new data on strontium isotope stratigraphy applied to the Miocene heterozoan shelfal carbonates of the S. Marino Fm. (Marecchia Valley, northern Apennines. Sr isotopic analyses were carried out on oyster shells, bryozoans and bulk-rocks from the lower-middle carbonate portion of the section. In the upper part of the succession that shows evidence of detrital influx,87Sr/86Sr analyses were performed on foraminifera tests, separating planktonic and benthic forms. Results were compared with calcareous nannofossil biostratigraphic data from the same levels, in order to test the reliability of Sr dating in mixed carbonate-siliciclastic sediments. Mean ages obtained from oysters range between 16.9 Ma and 16.3 Ma. Very similar results are obtained using bryozoans (16.5 Ma to 16.1 Ma and bulk-rocks (16.8 Ma to 16.2 Ma. These results allow to better constrain the age of the massive carbonate shelf, referable to the upper Burdigalian. In the upper carbonate-siliciclastic portion of the shelf, numerical ages obtained from planktonic and benthic foraminifera are in good agreement with nannofossil biozones (mean ages respectively around 15.3 Ma and 14.5 Ma although they display wide confidence intervals. These wide age uncertainties depend on the slow rate of change of marine 87Sr/86Sr through time that characterizes the interval between ~15 and ~13.5 Ma.

  15. Study on quaternary stratigraphy and environmental changes in South Sea, Korea

    Energy Technology Data Exchange (ETDEWEB)

    Chang, Jeong-Hae; Lee, Chi-Won; Kim, Sung-Pil [Korea Institute of Geology Mining and Materials, Taejon (KR)] (and others)

    1999-12-01

    According to interpretation of seismic profiles crossing the drilled sites, there are five sequences, namely Unit I, Unit II, Unit III, Unit IV and Unit V from bottom, separable by a reflector with good lateral continuity. If we apply the conception of sequential stratigraphy to the sea level fluctuation caused depositional processes, based on the results of seismic profiles, it will be possible to figure out the late Quaternary depositional processes in the context of sea level changes. According to the sedimentological and seismic stratigraphic analysis, most of SSDP sites showed transgression and regression sequences. Chemical analyses of elements for the sediment samples of SSDP-102 core exhibit the geochemical factors which may influenced the sedimentary environments of the study area. The lower-most sedimentary sequence Unit III can be interpreted as an environment which was influenced dominantly by stronger chemical weathering under a semi-fresh water environment. Based on predominance of carbonate-originated Ca in the homogeneous mud sequence, a high productive surface water along with transgression may have controlled the upper-most sedimentary sequence Unit I. Scatter diagram represents oxygen and carbon isotopic values of benthic foraminifera (Asterorotalia concinna) which is analyzed. All 61 points has value between +1 and -1. If isotopic values of selected benthic foraminifera are equilibrium with surrounding values. These distributions indicate transitional between coastal environment affected by fresh water and open marine environment. (author). 24 refs., 8 tabs., 25 figs.

  16. Depositional architecture and sequence stratigraphy of the Upper Jurassic Hanifa Formation, central Saudi Arabia

    Science.gov (United States)

    El-Sorogy, Abdelbaset; Al-Kahtany, Khaled; Almadani, Sattam; Tawfik, Mohamed

    2018-03-01

    To document the depositional architecture and sequence stratigraphy of the Upper Jurassic Hanifa Formation in central Saudi Arabia, three composite sections were examined, measured and thin section analysed at Al-Abakkayn, Sadous and Maashabah mountains. Fourteen microfacies types were identified, from wackestones to boundstones and which permits the recognition of five lithofacies associations in a carbonate platform. Lithofacies associations range from low energy, sponges, foraminifers and bioclastic burrowed offshoal deposits to moderate lithoclstic, peloidal and bioclastic foreshoal deposits in the lower part of the Hanifa while the upper part is dominated by corals, ooidal and peloidal high energy shoal deposits to moderate to low energy peloidal, stromatoporoids and other bioclastics back shoal deposits. The studied Hanifa Formation exhibits an obvious cyclicity, distinguishing from vertical variations in lithofacies types. These microfacies types are arranged in two third order sequences, the first sequence is equivalent to the lower part of the Hanifa Formation (Hawtah member) while the second one is equivalent to the upper part (Ulayyah member). Within these two sequences, there are three to six fourth-order high frequency sequences respectively in the studied sections.

  17. Holocene tephra stratigraphy in four lakes in southeastern Oregon and northwestern Nevada, USA

    Science.gov (United States)

    Foit, Franklin F.; Mehringer, Peter J.

    2016-03-01

    To better understand the regional tephra stratigraphy and chronology of northern Nevada and southern Oregon, tephras in archived cores, taken as part of the Steens Mountain Prehistory Project from four lakes, Diamond Pond, Fish and Wildhorse lakes in southeastern Oregon and Blue Lake in northwestern Nevada, were reexamined using more advanced electron microprobe analytical technology. The best preserved and most complete core from Fish Lake along with Wildhorse Lake hosted two tephras from Mt. Mazama (Llao Rock and the Climactic Mazama), a mid-Holocene basaltic tephra from Diamond Craters, Oregon, two Medicine Lake tephras and an unexpected late Holocene Chaos Crags (Mt. Lassen volcanic center) tephra which was also found in the other lakes. Blue Lake was the only lake that hosted a Devils Hill tephra from the Three Sisters volcano in west central Oregon. Another tephra from the Three Sisters Volcano previously reported in sediments of Twin Lakes in NE Oregon, has now been confirmed as Rock Mesa tephra. The Chaos Crags, Devils Hill and Rock Mesa tephras are important late Holocene stratigraphic markers for central and eastern Oregon and northwestern Nevada.

  18. Stratigraphy and palaeoenvironmental evolution of the mid- to upper Palaeozoic succession in Northwest Peninsular Malaysia

    Science.gov (United States)

    Amir Hassan, Meor H.; Aung, Aye-Ko; Becker, R. T.; Abdul Rahman, Noor Atirah; Ng, Tham Fatt; Ghani, Azman A.; Shuib, Mustaffa Kamal

    2014-04-01

    The stratigraphy of the Devonian to Permian succession in Northwest Peninsular Malaysia is revised. The Timah Tasoh Formation consists of black mudstone containing graptolites and tentaculitids indicating a Pragian or earliest Emsian age. The Sanai Limestone overlies the Timah Tasoh Formation at Sanai Hill B and contains conodonts indicating a Late Devonian (Frasnian to possibly early Famennian) age. In other places, Late Tournaisian chert of the Telaga Jatoh Formation overlies the Timah Tasoh Formation. The overlying Kubang Pasu Formation is predominantly composed of mudstone and sandstone, and can be divided into 3 subunits, from oldest to youngest: (1) Chepor Member; (2) Undifferentiated Kubang Pasu Formation; (3) Uppermost Kubang Pasu Formation. The ammonoid Praedaraelites tuntungensis sp. nov. is reported and described from the Chepor Member of Bukit Tuntung, Pauh. The genus indicates a Late Viséan age for part of the subunit. Dropstones and diamictites from the Chepor Member indicate a glacial marine depositional environment. The Carbo-Permian, undifferentiated Kubang Pasu Formation consists of similar interbedded mudstone and sandstone. The uppermost Kubang Pasu Formation of Kungurian age consists of coarsening upward cycles of clastics, representing a shallow marine, wave- and storm-influenced shoreline. The Permian Chuping Limestone also represents shallow marine, wave- and storm-influenced deposits. A Mid-Palaeozoic Unconformity separating Early-Late Devonian rocks from overlying Late Devonian-Carboniferous deposits probably marks initiation of rifting on Sibumasu, which eventually led to the separation of Sibumasu from Australian Gondwana during the late Sakmarian (Early Permian).

  19. Stratigraphy of Atlantic coastal margin of United States north of Cape Hatteras; brief survey

    Science.gov (United States)

    Perry, W.J.; Minard, J.P.; Weed, E.G.A.; Robbins, E.I.; Rhodehamel, E.C.

    1975-01-01

    A synthesis of studies of sea-floor outcrops of the sedimentary wedge beneath the northeastern United States continental shelf and slope and a reassessment of coastal plain Mesozoic stratigraphy, particularly of the coastal margin, provide insight for estimating the oil and gas potential and provide geologic control for marine seismic investigations of the Atlantic continental margin. The oldest strata known to crop out on the continental slope are late Campanian in age. The Cretaceous-Tertiary contact along the slope ranges from a water depth of 0.6 to 1.5 km south of Georges Bank to 1.8 km in Hudson Canyon. Few samples are available from Tertiary and Late Cretaceous outcrops along the slope. Sediments of the Potomac Group, chiefly of Early Cretaceous age, constitute a major deltaic sequence in the emerged coastal plain. This thick sequence lies under coastal Virginia, Maryland, Delaware, southeastern New Jersey, and the adjacent continental shelf. Marine sands associated with this deltaic sequence may be present seaward under the outer continental shelf. South of the Norfolk arch, under coastal North Carolina, carbonate rocks interfinger with Lower Cretaceous clastic strata. From all available data, Mesozoic correlations in coastal wells between coastal Virginia and Long Island have been revised. The Upper-Lower Cretaceous boundary is placed at the transition between Albian and Cenomanian floras. Potential hydrocarbon source beds are present along the coast in the subsurface sediments of Cretaceous age. Potential reservoir sandstones are abundant in this sequence.

  20. Yucatán subsurface stratigraphy: Implications and constraints for the Chicxulub impact

    Science.gov (United States)

    Ward, W. C.; Keller, G.; Stinnesbeck, W.; Adatte, T.

    1995-10-01

    Much of the discussion about the effects of an end-of-Cretaceous impact by a large extraterrestrial body in northwestern Yucatán has been done in the context of limited and partly erroneous published data on the Mesozoic stratigraphy of that area. Reexamination of cores and geophysical logs taken in several Pemex wells has produced improved lithologic and biostratigraphic correlation of the Jurassic to Maastrichtian section across the northern Yucatán peninsula. These data suggest that major disturbance of strata by an impact would have been confined to within about 100 km of the proposed impact center near Chicxulub. The only unusual lithologic unit is polymict breccia, which apparently was penetrated at or near the top of the Cretaceous section in all the deep wells of northern Yucatán. This breccia in Pemex wells Yucatán 1, 2, 4, 5A, and 6 is composed predominantly of detrital dolomite, limestone, and anhydrite clasts set in dolomitized carbonate mud matrix, which contains upper Maastrichtian foraminifers. These constituents, mixed with fragments of altered glass or melt rock, shocked quartz and feldspar, and basement rock, suggest an impact as the most likely origin for the breccia. The timing of brecciation is poorly constrained by biostratigraphic data. There is some evidence, however, that the breccia unit is overlain by about 18 m of uppermost Maastrichtian marls, suggesting an impact before the Cretaceous-Tertiary boundary. In addition, there may have been more than one episode of breccia deposition.

  1. Late Quaternary CaCO3 stratigraphy of the eastern equatorial Pacific

    Science.gov (United States)

    Snoeckx, Hilde; Rea, David K.

    1994-04-01

    Four patterns of CaCO3 abundance occur in cores retrieved from the eastern equatorial Pacific during the Venture 01 expedition. Core locations lie along a north-south transect at 110°W underneath the different currents of the equatorial current system and along an east-west transect from 110° to 90°W, at approximately 3°S, underneath the South Equatorial Current. The "classic" or central equatorial Pacific pattern of CaCO3 abundance maxima associated with glacial stages as defined by the δ18O record characterizes only a small portion of the area studied. In the area where the Peru current turns west to join the South Equatorial Current, the carbonate record is characterized by a broad low, centered on interglacial carbonate stage B-3 (approximately stage 5 in δ18O stratigraphy) overlying a broad mid-Brunhes maximum. Low-amplitude variations in CaCO3 percentages are superimposed on this pattern. This pattern extends westward in a long-wavelength pattern in which the B-3 carbonate low becomes decreasingly pronounced away from the equator. The fourth pattern, observed north of 10°N, is erratic and may be only local in extent.

  2. Sequence stratigraphy, basin dynamics, and petroleum geology of the Miocene from eastern Tunisia

    Energy Technology Data Exchange (ETDEWEB)

    Bedir, M. [Campus Universitaire, Tunis (Tunisia)]|[Unite des Ressources Naturelles et Environnement, Hammam-Lif (Tunisia); Tlig, S. [Campus Universitaire, Tunis (Tunisia); Bobier, C. [Universite Bordeaux, Talence (France)] [and others

    1996-01-01

    On the eastern margin of Tunisia, Miocene limestones, marl, and siliciclastic deposits crop out poorly and are lacking in age-diagnostic faunal content. The biostratigraphic and lithostratigraphic subdivisions of these series are not clearly defined. A regional study of subsurface sequences of this margin (Cap Bon, Gulf of Hammamet, and Sahel) by means of sequence stratigraphy and subsurface structural analyses permits the identification of seven third-order sedimentary sequences of inferred Langhian to Messinian age, the boundaries of which are characterized by downlap and onlap/toplap relationships. These sequences include turbidites, sands, and sandstones deposited in connection with eustatic sea level changes and tectonic movements of east-west and south-north deep-seated faults due to the Alpine and Atlassic paroxysm. Stratal sequences are organized around Miocene syndepositional grabens, half-grabens, platforms, and folds occurring inside and outside of regional tectonic corridors. The geodynamic evolution of Miocene basins has led to the deposition of turbiditic black argillaceous source rocks, and sandstone and carbonate reservoirs that present new Miocene petroleum targets. The basin subsidence in response to the Alpine/Atlassic orogeny has permitted the maturation of Miocene source rocks, oil generation, and the formation of oil traps, stratigraphic pinch-outs, and structural enclosures on the flanks of folds and on the borders of grabens.

  3. Stratigraphy of the Descartes region /Apollo 16/ - Implications for the origin of samples

    Science.gov (United States)

    Head, J. W.

    1974-01-01

    Analysis of terrain in the Apollo 16 Descartes landing region shows a series of features that form a stratigraphic sequence which dominates the history and petrogenesis at the site. An ancient 150-km diam crater centered on the Apollo 16 site is one of the earliest recognizable major structures. Nectaris ejecta was concentrated in a regional low at the base of the back slope of the Nectaris basin to form the Descartes Mountains. Subsequently, a 60-km diam crater formed in the Descartes Mountains centered about 25 km to the west of the site. This crater dominates the geology and petrogenetic history of the site. Stone and Smoky Mountains represent the degraded terraced crater walls, and the dark matrix breccias and metaclastic rocks derived from North and South Ray craters represent floor fallback breccias from this cratering event. The interpretation is developed that the stratigraphy of the Cayley and Descartes, and thus the historical record of the Apollo 16 region, documents the complex interaction of deposits and morphology of local and regional impact cratering events. Large local 60- to 150-km diam craters have had a dramatic and previously unrecognized effect on the history and petrology of the Apollo 16 site.

  4. Extending the flood record on the Middle Gila River with Holocene stratigraphy

    Energy Technology Data Exchange (ETDEWEB)

    Huckleberry, G. (Univ. of Arizona, Tucson, AZ (United States). Dept. of Geosciences)

    1993-04-01

    Historical changes in flood frequency and magnitude are correlated to changes in channel geometry for the Middle Gila River (MGR) in south-central Arizona. The author has attempted to reconstruct the frequency of large floods on the MGR for the last 1,000 years by looking at the stratigraphic record with the purpose of modeling channel changes during a period of significant local cultural change, i.e., the Hohokam-Pima cultural transition. After distinguishing and mapping geological surfaces in the eastern part of the Gila River Indian Community. The author placed a series of backhoe trenches on late Holocene MGR terraces. He interprets lithological discontinuities within overbank deposits as boundaries separating temporally discrete floods. Detrital charcoal from within the stratigraphy was submitted to the National Science Foundation-University of Arizona AMS facility for radiocarbon analysis. The stratigraphic record indicates that a minimum of four large floods have occurred on the MGR since A.D. 1300. Three of these floods may correspond to large historical floods in 1833, 1868, and 1905. If so, then it appears that MGR flood frequency increased after A.D. 1800. There is no evidence for increased flood frequency and channel transformations during the cultural decline of the Hohokam in the 15th century.

  5. Fluid dynamic transient analysis

    International Nuclear Information System (INIS)

    Vilhena Reigosa, R. de

    1992-01-01

    This paper describes the methodology adopted at NUCLEN for the fluid dynamic analyses for ANGRA 2. The fluid dynamic analysis allows, through computer codes to simulate and quantify the loads resulting from fluid dynamic transients caused by postulated ruptures or operational transients, in the piping of the safety systems and of the important operational systems. (author)

  6. Amniotic fluid water dynamics

    NARCIS (Netherlands)

    Beall, M. H.; van den Wijngaard, J. P. H. M.; van Gemert, M. J. C.; Ross, M. G.

    2007-01-01

    Water arrives in the mammalian gestation from the maternal circulation across the placenta. It then circulates between the fetal water compartments, including the fetal body compartments, the placenta and the amniotic fluid. Amniotic fluid is created by the flow of fluid from the fetal lung and

  7. Fundamental Fluid Mechanics

    Indian Academy of Sciences (India)

    BOOK I REVIEW. Fundamental Fluid. Mechanics. Good Text Book Material. V H Arakeri. Fluid Mechanics for Engineers. P N Chatterjee. MacMillan India Limited. Vol. 1, pp. 367. RS.143. Vo1.2, pp.306. RS.130. Fluid Mechanics for Engineers in two vol- umes by P N Chatterjee contains standard material for a first level ...

  8. Inclusion study of hourglass amethyst from Boudi (Morocco) by Raman microspectroscopy and microthermometric measurements

    Science.gov (United States)

    Dumańska-Słowik, Magdalena; Toboła, Tomasz; Jarmołowicz-Szulc, Katarzyna; Naglik, Beata; Dyląg, Joanna; Szczerba, Jacek

    2017-12-01

    Amethyst from Boudi with characteristic hourglass colour zoning hosts numerous pseudo-secondary fluid and mineral inclusions. Measured values of temperature homogenization (Th) for selected fluid inclusion assemblages (FIA) in colourless and violet regions of the crystal range from 154 to 330 °C. The higher temperatures values are characteristic for violet zones than colourless regions of the crystal. The brine content and concentration vary from 5.71 to 13.94 wt% NaCl eq. Raman spectra of selected fluid inclusions revealed they are mainly composed of H2O (3500-3000 cm- 1) and subordinately CO2 both gaseous and liquid (1386 cm- 1 and 1281 cm- 1). Mineral inclusions are mainly represented by hematite with marker bands at 1321, 413, 293 and 227 cm- 1, subordinately quartz. Amethyst crystallized from medium- to low-temperature silica fluids (191-445 °C, 64-131 MPa) containing some amounts of CO2 and Fe at hydrothermal stage of post magmatic activity in Boudi (Morocco). Its possible depth of formation was calculated to be ca. 2.8-5.7 km.

  9. Inclusive and semi-inclusive hadron interactions at ISR energies

    International Nuclear Information System (INIS)

    Giacomelli, G.

    1987-01-01

    Experiments at the CERN proton-antiproton collider and at the ISR have recently provided a wealth of information on high-energy, low-transverse momentum hadron-hadron interactions. These data are changing the picture of inelastic collisions at high-energies. In this paper will be mainly discussed high-statistics data from the ABCDHW collaboration using the Split Field Magnet (SFM) detector at the CERN-ISR. In particular will be discussed inclusive distributions as functions of x and y, the multiplicity and rapidity dependence of the mean transverse momentum, its fluctuations, correlations in rapidity, Bose-Einstein correlations, charged multiplicity distributions and rapidity fluctuations

  10. Fluid and particle mechanics

    CERN Document Server

    Michell, S J

    2013-01-01

    Fluid and Particle Mechanics provides information pertinent to hydraulics or fluid mechanics. This book discusses the properties and behavior of liquids and gases in motion and at rest. Organized into nine chapters, this book begins with an overview of the science of fluid mechanics that is subdivided accordingly into two main branches, namely, fluid statics and fluid dynamics. This text then examines the flowmeter devices used for the measurement of flow of liquids and gases. Other chapters consider the principle of resistance in open channel flow, which is based on improper application of th

  11. Event by Event fluctuations and Inclusive Distribution

    OpenAIRE

    Bialas, A.; Koch, V.

    1999-01-01

    Event-by-event observables are compared with conventional inclusive measurements. We find that moments of event-by-event fluctuations are closely related to inclusive correlation functions. Implications for upcomming heavy ion experiments are discussed.

  12. Inclusive outreach practices in Palaeontology: Inclusive-Coworking

    Science.gov (United States)

    García-Frank, Alejandra; Gomez-Heras, Miguel; Fesharaki, Omid

    2017-04-01

    Previous experiences with people with both physical and intellectual functional diversity around palaeontological issues have demonstrated the important value of science outreach directed to people with disabilities. The aforementioned practices act twofold: as a learning tool and also improving the quality of life of the participants and thus, their self-image. All these pioneer experiences were the first step in a process of developing new attitudes contributing the 2030 Agenda for Sustainable Development of United Nations, where among the 17 goals proposed an effective social inclusion of people with disabilities is required. For this, real inclusive practices in geological outreach are imperious. A close cooperation with all the parts (researchers and participants), in a kind of coworking attitude is needed. This Inclusive-Coworking is considered in the sense of social gathering in order to share equal values and look for the synergy that this different outlook implies. And what is more important: the change of role of the previously learners into an active part of the scientific outreach, providing the adequate methodology for that. The offer of non-formal learning activities normally includes the participation of university professors and researchers in Science Week editions. During the 2016 session in Madrid, four adults with intellectual disability who were participants in the previous edition, contributed in the palaeontological workshop. They were in charge of four of the eight modules explaining the origin of fossils and how to collect them, the evolution of equids' limbs, and the main dentition types in vertebrates to the twenty 16 year old secondary students who attended the workshop. During the development of the experience all the students were pleased with the inclusive approach, and the interaction of all participants was fruitful. Although the explanations took a bit more time when made by our functional diverse fellows, all the abstracts concepts

  13. Spinning fluids reactor

    Science.gov (United States)

    Miller, Jan D; Hupka, Jan; Aranowski, Robert

    2012-11-20

    A spinning fluids reactor, includes a reactor body (24) having a circular cross-section and a fluid contactor screen (26) within the reactor body (24). The fluid contactor screen (26) having a plurality of apertures and a circular cross-section concentric with the reactor body (24) for a length thus forming an inner volume (28) bound by the fluid contactor screen (26) and an outer volume (30) bound by the reactor body (24) and the fluid contactor screen (26). A primary inlet (20) can be operatively connected to the reactor body (24) and can be configured to produce flow-through first spinning flow of a first fluid within the inner volume (28). A secondary inlet (22) can similarly be operatively connected to the reactor body (24) and can be configured to produce a second flow of a second fluid within the outer volume (30) which is optionally spinning.

  14. Intravenous fluids: balancing solutions.

    Science.gov (United States)

    Hoorn, Ewout J

    2017-08-01

    The topic of intravenous (IV) fluids may be regarded as "reverse nephrology", because nephrologists usually treat to remove fluids rather than to infuse them. However, because nephrology is deeply rooted in fluid, electrolyte, and acid-base balance, IV fluids belong in the realm of our specialty. The field of IV fluid therapy is in motion due to the increasing use of balanced crystalloids, partly fueled by the advent of new solutions. This review aims to capture these recent developments by critically evaluating the current evidence base. It will review both indications and complications of IV fluid therapy, including the characteristics of the currently available solutions. It will also cover the use of IV fluids in specific settings such as kidney transplantation and pediatrics. Finally, this review will address the pathogenesis of saline-induced hyperchloremic acidosis, its potential effect on outcomes, and the question if this should lead to a definitive switch to balanced solutions.

  15. Microvillous inclusion disease (microvillous atrophy

    Directory of Open Access Journals (Sweden)

    Goulet Olivier

    2006-06-01

    Full Text Available Abstract Microvillous inclusion disease (MVID or microvillous atrophy is a congenital disorder of the intestinal epithelial cells that presents with persistent life-threatening watery diarrhea and is characterized by morphological enterocyte abnormalities. MVID manifests either in the first days of life (early-onset form or in the first two months (late-onset form of life. MVID is a very rare disorder of unknown origin, probably transmitted as an autosomal recessive trait. To date, no prevalence data are available. Ultrastructural analyses reveal: 1 a partial to total atrophy of microvilli on mature enterocytes with apical accumulation of numerous secretory granules in immature enterocytes; 2 the highly characteristic inclusion bodies containing rudimentary or fully differentiated microvilli in mature enterocytes. Light microscopy shows accumulation of PAS-positive granules at the apical pole of immature enterocytes, together with atrophic band indicating microvillus atrophy and, in parallel, an intracellular PAS or CD10 positive line (marking the microvillous inclusion bodies seen on electron microscopy. Intestinal failure secondary to diarrhea is definitive. To date, no curative therapy exists and children with MVID are totally dependent on parenteral nutrition. Long-term outcome is generally poor, due to metabolic decompensation, repeated states of dehydration, infectious and liver complications related to the parenteral nutrition. As MVID is a very rare disorder, which is extremely difficult to diagnose and manage, children with MVID should be transferred to specialized pediatric gastro-intestinal centers, if possible, a center equipped to perform small bowel transplantation. Early small bowel transplantation resulting in intestinal autonomy gives new hope for disease management and outcome.

  16. Regge cuts in inclusive reactions

    International Nuclear Information System (INIS)

    Paige, F.E.; Trueman, T.L.

    1975-01-01

    The contribution of Regge cuts to single-particle inclusive processes is analyzed using the techniques of Gribov. The dependence of these contributions on the polarization state of the target is emphasized. A general formula is obtained and certain contributions to it are calculated. It is not possible, however, to reduce this to a simple, powerful formula expressing the total cut contribution in terms of other measurable quantities, as can be done for the cut contribution to the total cross section. The reasons for this are discussed in detail. The single-particle intermediate states, analogous to the absorption model for elastic scattering, are explicitly calculated as an illustration

  17. Teaching Competences and Inclusive Education

    Directory of Open Access Journals (Sweden)

    José María Fernández Batanero

    2013-08-01

    Full Text Available This paper focuses on teaching competencies that are conducive to good educational practices in relation to inclusion, from the perspective of teachers. The methodology employed in the study is descriptive/comprehensive, and of an exploratory nature. By means of four case studies, the perceptions of teachers from two secondary schools—characterized by the Spanish Educational Administration as having “good practices”— are examined. The techniques used for information collection in this study include documentary analysis, in-depth interviews and focus groups. The findings emphasize the importance of strategic skills, combined with innovation and creativity, among others.

  18. Affectionally Fluid Persons' Beliefs about Wellness

    Science.gov (United States)

    Finnerty, Peter S.

    2017-01-01

    The purpose of this study was to examine affectionally fluid (AF) persons' beliefs about wellness. A total of 44 participants met the inclusion criteria of identifying as AF for the Q methodology study. These participants sorted 32 statements from most agree with my beliefs about wellness to most disagree with my beliefs, utilizing a response grid…

  19. Mechanism of chain formation in nanofluid based MR fluids

    International Nuclear Information System (INIS)

    Patel, Rajesh

    2011-01-01

    Mechanism of structure formation in bidispersed colloids is important for its physical and optical properties. It is microscopically observed that the mechanism of chain formation in magnetic nanofluid based magnetorheological (MR) fluid is quite different from that in the conventional MR fluid. Under the application of magnetic field the magnetic nanoparticles are filled inside the structural microcavities formed due to the association of large magnetic particles, and some of the magnetic nanoparticles are attached at the end of the chains formed by the large particles. The dipolar energy of the large particles in a magnetic nanofluid matrix becomes effective magnetic permeability (μ eff ) times smaller than that of the neutral medium. Inclusion of magnetic nanoparticles (∼10 nm) with large magnetic particles (∼3-5 μm) restricts the aggregation of large particles, which causes the field induced phase separation in MR fluids. Hence, nanofluid based MR fluids are more stable than conventional MR fluids, which subsequently increase their application potentiality. - Research highlights: → In bidispersed magnetic colloids nanoparticles are attached at the end of the chains formed by the large particles. → Inclusion of magnetic nanoparticles (∼10 nm) with large magnetic particles (∼3-5 m) restricts the aggregation of large particles. → Nanofluid based MR fluids are more stable than conventional MR fluids.

  20. Principals' Knowledge of and Attitudes toward Inclusion.

    Science.gov (United States)

    Barnett, Carol; Monda-Amaya, Lisa E.

    1998-01-01

    A survey of 65 elementary, junior, and high school principals investigated attitudes toward and knowledge of inclusion. No clear definition of inclusion emerged, but principals generally viewed inclusion as most appropriate for students with mild disabilities. Also, results indicated that teachers were not adequately prepared to implement…

  1. Inclusive Education: Examining Equity on Five Continents

    Science.gov (United States)

    Artiles, Alfredo J., Ed.; Kozleski, Elizabeth B., Ed.; Waitoller, Federico R., Ed.

    2011-01-01

    Despite the impressive growth of inclusive education around the world, questions and considerations about equity have been neglected. This edited volume makes a major contribution to the field of inclusive education by analyzing equity concerns that have emerged from the implementation of inclusive education models in nine nations on five…

  2. 75 FR 81395 - Minority and Women Inclusion

    Science.gov (United States)

    2010-12-28

    ... 2590-AA28 Minority and Women Inclusion AGENCIES: Federal Housing Finance Board; Federal Housing Finance... and the inclusion of women and minorities in all activities. The final rule implements the provisions.... It also requires each regulated entity to establish an Office of Minority and Women Inclusion, or...

  3. 75 FR 10446 - Minority and Women Inclusion

    Science.gov (United States)

    2010-03-08

    ... 2590-AA28 Minority and Women Inclusion AGENCIES: Federal Housing Finance Board; Federal Housing Finance... minority and women inclusion. Section 1116 of the Housing and Economic Recovery Act of 2008 amended section... Loan Banks to promote diversity and the inclusion of women and minorities in all activities...

  4. Teachers' Experience with Inclusive Education in Singapore

    Science.gov (United States)

    Yeo, Lay See; Chong, Wan Har; Neihart, Maureen F.; Huan, Vivien S.

    2016-01-01

    Teachers' positive attitude is most critically and consistently associated with successful inclusion. However, little is known about teachers' first-hand encounters with inclusive education in Singapore. We present findings from a qualitative study on inclusion based on focus group interviews with 202 teachers from 41 resourced primary schools.…

  5. "Inclusion in Practice": Does Practice Make Perfect?

    Science.gov (United States)

    Slee, Roger

    2001-01-01

    Discusses four issues raised in this special issue: (1) problems with the term "inclusion"; (2) reductionist approaches to inclusive education; (3) politics of special education research and the need to include parent and student voices; and (4) preparation of teachers for inclusive education. (Contains 53 references.) (SK)

  6. Inclusive Classes in Physical Education: Teachers' Difficulties

    Science.gov (United States)

    Toloi, Gabriela Gallucci; Manzini, Eduardo José; Spoldaro, Diego Machado; Zacarias, Lucas Ventura

    2016-01-01

    The successful inclusion of students with special needs in physical education classes requires much planning and preparation. Lack of preparation of physical education teachers working in inclusive settings in Brazil has demonstrated the need for specialized training in strategies for implementing inclusion. The goal of this study was to identify,…

  7. Ultrastructural cytochemical analysis of intranuclear arsenic inclusions

    Energy Technology Data Exchange (ETDEWEB)

    Sorensen, E.M.B.

    1987-01-01

    To establish the chemical composition of the arsenic inclusion, freshly isolated preparations of inclusions and epon-embedded thin sections of inclusions were subjected to ultrastructural cytochemical analysis. Intranuclear inclusions are composed of amorphous, arsenic-containing subunits aligned linearly to form a coiled complex. Lipase, ribonuclease, deoxyribonuclease, trypsin, pepsin, protease, amylase, or ethylenediaminetetraacetic acid (EDTA) was used to digest or chelate these inclusions. Following enzymatic digestion or chelation, the electron opacity of inclusions was compared with that of control sections exposed for equal times to equivalent solutions lacking the enzymes. Exposure to amylase caused a consistent reduction in the electron opacity of thin sections of inclusions and almost complete digestion of the freshly isolated preparations of inclusions. This was indicative of the presence of a carbohydrate moiety within arsenic inclusions. Incubation of inclusions with EDTA resulted in solubilization of freshly isolated and thin-sectioned embedded material. These data indicated that the intranuclear arsenic inclusion is composed of both metallic and carbohydrate moieties, confirming earlier studies which identified arsenic within inclusions using instrumental neutron activation analysis and x-ray microprobe analysis.

  8. Full averaging of fuzzy impulsive differential inclusions

    Directory of Open Access Journals (Sweden)

    Natalia V. Skripnik

    2010-09-01

    Full Text Available In this paper the substantiation of the method of full averaging for fuzzy impulsive differential inclusions is studied. We extend the similar results for impulsive differential inclusions with Hukuhara derivative (Skripnik, 2007, for fuzzy impulsive differential equations (Plotnikov and Skripnik, 2009, and for fuzzy differential inclusions (Skripnik, 2009.

  9. Elements of Inclusion: Findings from the Field

    Science.gov (United States)

    McMaster, Christopher

    2014-01-01

    The Ministry of Education has set the target of 100% of New Zealand schools to be "mostly" inclusive by 2014. But what are the essential elements of inclusion? This paper explores essential core elements that allow inclusion to flourish. Based on an extensive time in the field as part of a year-long doctoral research project, these…

  10. Curcumin-Hydroxypropyl-β-Cyclodextrin Inclusion Complex ...

    African Journals Online (AJOL)

    Purpose: To evaluate the effect of the preparation method on the inclusion complex of curcumin and hydroxypropyl-β-cyclodextrin Methods: HP-β-CD was selected to prepare an inclusion complex with curcumin at a molar ratio of 1:1. The inclusion complexes were prepared using three different methods: common solvent ...

  11. Measuring Inclusive Education Outcomes in Alberta, Canada

    Science.gov (United States)

    Loreman, Tim

    2014-01-01

    This study details the results of a review of the academic and public sector literature on measuring inclusive education in large systems. It highlights some outcomes drawn from the international literature on inclusion that might be indicative of the presence and quality of inclusive education in an effort to develop a set of outcomes for…

  12. Existence of solutions of functional differential inclusions

    Directory of Open Access Journals (Sweden)

    A. Anguraj

    1992-01-01

    Full Text Available We prove the existence of solutions of a functional differential inclusion. By using the variation of parameters formula we convert the functional differential inclusion into an integral inclusion and prove the existence of a fixed point of the set-valued mapping with the help of the Kakutani-Bohnenblust-Karlin fixed point theorem.

  13. The base of the Campanian: a magnetostratigraphic definition, integrated biostratigraphy and isotope stratigraphy

    Science.gov (United States)

    Wagreich, Michael; Dinarès-Turell, Jaume; Wolfgring, Erik; Omer Yilmaz, Ismail

    2017-04-01

    The base of the Campanian, the longest stage of the Late Cretaceous, is still not defined by a GSSP (Global Boundary Stratotype Section and Point). Furthermore, no consensus exists about the boundary criterion: macrofossils like ammonites and inoceramids suffer from bioprovincialism. The LAD of the crinoid Marsupites testudinarius was proposed as the primary fossil marker. But this marker is mainly a chalk facies fossil, which is rare to absent in pelagic low-latitudes, absent in oceanic sections, and the LAD may be influenced by palaeoenvironmental and palaecological settings. More recently, a boundary defined by magnetostratigraphy, i.e. the base of Chron C33r after the Long Cretaceous Normal Chron C34n, has been discussed. Western Tethyan pelagic sections from Austria and Turkey provide means for integrating various stratigraphic methods. A robust magnetostratigraphic signal was found at the Postalm section (Gosau Group, Northern Calcareous Alps, Austria) which may serve as a reference section for the northwestern Tethys. Including nearby complementary sections, palaeomagnetic data can be integrated with strontium isotope stratigraphy and stable isotope data, planktonic foraminifera and calcareous nannoplankton biostratigraphy, , and ammonite, crinoid and inoceramid data. The Postalm section shows a deepening trend from upper Santonian conglomerates and grey shelf marls to pelagic bathyal red marly limestones of Campanian age. Palaeomagnetic data allow identifying the top of Chron C34n and the following reversal in the lower part of the red marly limestones. A 1 m-thick interval of high magnetic susceptibility is present at the end of C34n. Two of the main suggested biomarkers to pinpoint the Santonian-Campanian boundary, i.e. the last occurrence of the planktonic foraminifer Dicarinella asymetrica and the first occurrence of the nannofossil Broinsonia parca parca, occur in close proximity to the reversal, which is suggested herein as the primary marker event

  14. Great earthquakes along the Western United States continental margin: implications for hazards, stratigraphy and turbidite lithology

    Science.gov (United States)

    Nelson, C. H.; Gutiérrez Pastor, J.; Goldfinger, C.; Escutia, C.

    2012-11-01

    We summarize the importance of great earthquakes (Mw ≳ 8) for hazards, stratigraphy of basin floors, and turbidite lithology along the active tectonic continental margins of the Cascadia subduction zone and the northern San Andreas Transform Fault by utilizing studies of swath bathymetry visual core descriptions, grain size analysis, X-ray radiographs and physical properties. Recurrence times of Holocene turbidites as proxies for earthquakes on the Cascadia and northern California margins are analyzed using two methods: (1) radiometric dating (14C method), and (2) relative dating, using hemipelagic sediment thickness and sedimentation rates (H method). The H method provides (1) the best estimate of minimum recurrence times, which are the most important for seismic hazards risk analysis, and (2) the most complete dataset of recurrence times, which shows a normal distribution pattern for paleoseismic turbidite frequencies. We observe that, on these tectonically active continental margins, during the sea-level highstand of Holocene time, triggering of turbidity currents is controlled dominantly by earthquakes, and paleoseismic turbidites have an average recurrence time of ~550 yr in northern Cascadia Basin and ~200 yr along northern California margin. The minimum recurrence times for great earthquakes are approximately 300 yr for the Cascadia subduction zone and 130 yr for the northern San Andreas Fault, which indicates both fault systems are in (Cascadia) or very close (San Andreas) to the early window for another great earthquake. On active tectonic margins with great earthquakes, the volumes of mass transport deposits (MTDs) are limited on basin floors along the margins. The maximum run-out distances of MTD sheets across abyssal-basin floors along active margins are an order of magnitude less (~100 km) than on passive margins (~1000 km). The great earthquakes along the Cascadia and northern California margins cause seismic strengthening of the sediment, which

  15. Great earthquakes along the Western United States continental margin: implications for hazards, stratigraphy and turbidite lithology

    Directory of Open Access Journals (Sweden)

    C. H. Nelson

    2012-11-01

    Full Text Available We summarize the importance of great earthquakes (Mw ≳ 8 for hazards, stratigraphy of basin floors, and turbidite lithology along the active tectonic continental margins of the Cascadia subduction zone and the northern San Andreas Transform Fault by utilizing studies of swath bathymetry visual core descriptions, grain size analysis, X-ray radiographs and physical properties. Recurrence times of Holocene turbidites as proxies for earthquakes on the Cascadia and northern California margins are analyzed using two methods: (1 radiometric dating (14C method, and (2 relative dating, using hemipelagic sediment thickness and sedimentation rates (H method. The H method provides (1 the best estimate of minimum recurrence times, which are the most important for seismic hazards risk analysis, and (2 the most complete dataset of recurrence times, which shows a normal distribution pattern for paleoseismic turbidite frequencies. We observe that, on these tectonically active continental margins, during the sea-level highstand of Holocene time, triggering of turbidity currents is controlled dominantly by earthquakes, and paleoseismic turbidites have an average recurrence time of ~550 yr in northern Cascadia Basin and ~200 yr along northern California margin. The minimum recurrence times for great earthquakes are approximately 300 yr for the Cascadia subduction zone and 130 yr for the northern San Andreas Fault, which indicates both fault systems are in (Cascadia or very close (San Andreas to the early window for another great earthquake.

    On active tectonic margins with great earthquakes, the volumes of mass transport deposits (MTDs are limited on basin floors along the margins. The maximum run-out distances of MTD sheets across abyssal-basin floors along active margins are an order of magnitude less (~100 km than on passive margins (~1000 km. The great earthquakes along the Cascadia and northern California margins

  16. Transport Policy and Social Inclusion

    Directory of Open Access Journals (Sweden)

    Miriam Ricci

    2016-06-01

    Full Text Available ‘Transport-related Social inclusion’ is a specific naming of the complex set of interrelationships within which accessibility plays an important role in whether a citizen achieves the level of participation in socioeconomic life that he or she seeks. It has its origins in the United Kingdom of the early 2000s, but the diversity of theoretical perspectives, research methods and practical focus shown by the contributions to the present issue on this theme bears witness to the evolution and translation this concept and term has undergone over more than a decade. Nine papers are presented, concerning applications of the concept in three continents, and including some of the poorest and richest per capita income countries on the globe. As well as developing and applying the multi-faceted theories of the processes of exclusion and techniques for the quantitative identification of inclusion, they consider important topics such as the treatment of the less abled and more frail members of society when on the move and the potential for new technological design methods and practical solutions either to enhance inclusion or deepen inequality in our societies. Collectively their conclusions reinforce the message that social exclusion remains multi-dimensional, relational and dynamic, located both in the circumstances of the excluded individual as well as in the processes, institutions and structures that permeate wider society.

  17. Semi-inclusive DIS: Factorization

    Energy Technology Data Exchange (ETDEWEB)

    Yuan, Feng

    2008-12-10

    In this talk, we will present a QCD factorization theorem for the semi-inclusive deep-inelastic scattering with hadrons in the current fragmentation region detected at low transverse momentum. There has been considerable experimental and theoretical interest in semi-inclusive hadron production in deep inelastic scattering (SIDIS) processes. For example, by studying the polarized and unpolarized SIDIS, one will be able to identify the sea quark distribution and polarization in nucleon, and the experimental results from the HERMES collaboration have revealed nontrivial sea structure in nucleon [1]. More recently, SIDIS opened a new window to study the transverse momentum dependent (TMD) parton distributions and fragmentation functions from the low transverse momentum hadron production. The transverse momentum distribution of the final state hadron is directly related to the transverse momentum dependence of the parton distributions and fragmentation. These studies will provide new opportunities to explore the partonic structure of nucleon, especially the three-dimension distribution of partons inside nucleon. The DIS experiments, including HERMES, COMPAS, and JLab Hall B collaborations, have studied various azimuthal asymmetries in SIDIS. In particular, the HERMES collaboration found sizable single spin asymmetries in these processes involving nontrivial QCD effects and hadron structure.

  18. Seismic stratigraphy of the Heuksan mud belt in the southeastern Yellow Sea, Korea

    Science.gov (United States)

    Lee, Gwang-Soo; Yoo, Dong Geun; Bae, Sung Ho; Min, Gun-Hong; Kim, Seong-Pil; Choi, Hunsoo

    2015-12-01

    To establish the seismic stratigraphy of the Heuksan mud belt (HMB) and reconstruct its depositional history, approximately 1,600 km of high-resolution seismic data were newly obtained using chirp acoustic sub-bottom profiler, sparker, and air-gun seismic systems. Based on seismic stratigraphic analysis, the HMB can be divided into three major seismic units (I, II, and III, from top to bottom) and four subunits (II-a, II-b, III-a, and III-b) overlying transgressive sands, pre-last glacial maximum (LGM) deposits, and the acoustic basement. Each unit and subunit show different seismic facies and geometry, being clearly separated from each other by bounding surfaces formed since the LGM. The spatial distribution, thicknesses and volumes of the seismic units were determined and plotted to document the sequential formation of the HMB. The correlation between deep drill core data (HMB-101, HMB-102, HMB-103, YSDP-101, and YSDP-102) and the seismic data suggests that subunits III-b and III-a were formed by the continuous accumulation of fine-grained sediment with partial sandy sediment in an estuarine/deltaic environment during the early to middle transgressive stage, accompanied by landward migration of the shoreline. Subunits II-b and II-a were probably formed by re-deposition of large volumes of sediment eroded from unit III during the middle transgressive to early highstand stage. Unit I is interpreted as the most recent mud deposit representing the highstand systems tract when sea-level rise terminated. The careful definition of seismic units and their interpretation proposed in this study, on the basis of the large and partly new seismic dataset covering the entire HMB together with deep drill core data, have been instrumental in reconstructing the depositional environment and formation mechanisms of the HMB.

  19. Sediment yield model implementation based on check dam infill stratigraphy in a semiarid Mediterranean catchment

    Directory of Open Access Journals (Sweden)

    G. Bussi

    2013-08-01

    Full Text Available Soil loss and sediment transport in Mediterranean areas are driven by complex non-linear processes which have been only partially understood. Distributed models can be very helpful tools for understanding the catchment-scale phenomena which lead to soil erosion and sediment transport. In this study, a modelling approach is proposed to reproduce and evaluate erosion and sediment yield processes in a Mediterranean catchment (Rambla del Poyo, Valencia, Spain. Due to the lack of sediment transport records for model calibration and validation, a detailed description of the alluvial stratigraphy infilling a check dam that drains a 12.9 km2 sub-catchment was used as indirect information of sediment yield data. These dam infill sediments showed evidences of at least 15 depositional events (floods over the time period 1990–2009. The TETIS model, a distributed conceptual hydrological and sediment model, was coupled to the Sediment Trap Efficiency for Small Ponds (STEP model for reproducing reservoir retention, and it was calibrated and validated using the sedimentation volume estimated for the depositional units associated with discrete runoff events. The results show relatively low net erosion rates compared to other Mediterranean catchments (0.136 Mg ha−1 yr−1, probably due to the extensive outcrops of limestone bedrock, thin soils and rather homogeneous vegetation cover. The simulated sediment production and transport rates offer model satisfactory results, further supported by in-site palaeohydrological evidences and spatial validation using additional check dams, showing the great potential of the presented data assimilation methodology for the quantitative analysis of sediment dynamics in ungauged Mediterranean basins.

  20. Integrated stratigraphy and geochemistry of the Early Jurassic Posidonienschiefer from the Lower Saxony Basin, NW Germany

    Science.gov (United States)

    Celestino, Ricardo; Ruhl, Micha; Dickson, Alexander J.; Jenkyns, Hugh C.; Idiz, Erdem; Huggett, Jennifer; Mattioli, Emanuela; Minisini, Daniel; Weijers, Johan; Tegelaar, Erik; Hesselbo, Stephen P.

    2017-04-01

    The Posidonienschiefer (Early Jurassic, 183 Ma) is the expression of the Toarcian Oceanic Anoxic Event (T-OAE) in Germany and Northern Switzerland and comparable to its correlative units in the UK (Jet Rock) and France (Schistes Carton) is composed of organic-rich, laminated clayey and calcareous mudstone. The carbon isotope record is marked by the occurrence of an up to 7 ‰ negative excursion, both in bulk carbonate and organic carbon, thought to have been caused by a large release of methane (from gas hydrates, thermal metamorphic processes and/or volcanogenic sources). The sedimentology, biostratigraphy, organic geochemistry, astrochronology, and isotope chemostratigraphy of the Posidonienschiefer have been largely described in the literature, but most of the studies have focused on the regions of Southern Germany and Northern Switzerland with less information available from Northern Germany due to a lack of outcropping sections. Here we complement the existing datasets from NW Europe with an integrated study performed on cores from the Lower Saxony Basin, Northern Germany, an area that is still poorly correlated with the better known southern German localities. In particular, we present new results from high-resolution carbon-isotope stratigraphy, biostratigraphy and hand-held XRF analysis combined with quantitative mineralogy and organic geochemistry. Further advances in understanding are likely to come from taking a broader palaeogeographic overview of the development of the T-OAE through the whole of the Toarcian Stage, including consideration of sea-level and palaeoclimatic cycles that both pre-date and post-date the core negative carbon-isotope excursion. The new observations from Northern Germany indicate substantial differences in the expression of the T-OAE (duration of maximum organic carbon enrichment/development of hiatuses) compared to other locations from the Laurasian Seaway of NW Europe, contributing to a detailed understanding of the

  1. Investigating the stratigraphy of Mare Imbrium flow emplacement with Earth-based radar

    Science.gov (United States)

    Morgan, G. A.; Campbell, B. A.; Campbell, D. B.; Hawke, B. R.

    2016-08-01

    The lunar maria are the product of extensive basaltic volcanism that flooded widespread portions of the Moon's surface. Constraining mare volcanic history therefore provides a window into the endogenic processes responsible for shaping the Moon. Due to the low magma viscosity and the associated thin nature of lava units, the majority of mare surface structures are masked and subdued by impact regolith. Subtle individual mare flow morphologies, coupled with spatial limitations in the use of crater size distributions to distinguish surface units close in age, restrict our understanding of mare stratigraphy. Earth-based 70 cm wavelength (P band) radar can reveal features beneath the regolith and highlight very subtle changes in the ilmenite content of the flows, providing a unique means to map mare units. Here we map volcanic units in Mare Imbrium using high-resolution (200 m/pixel), Earth-based P band data. Situated within the heat-producing potassium, rare earth element, and phosphorus terrane, Mare Imbrium experienced some of the most long-lived (and recent) lunar volcanism, and its surface exhibits a significant diversity of basaltic chemistry. Our investigation identifies at least four distinct stages of volcanic activity, originating from multiple sources within Imbrium. The most recent of these stages comprises extensive, yet relatively thin volcanic flow units that left remnant kipukas of older mare material distributed across much of the basin. From a future mission perspective, it may be possible to collect samples expressing a wide range in age from small areas of Mare Imbrium. Our map also places important constraints on the interpretation of the Chang'e-3 Lunar Penetrating Radar measurements.

  2. Middle Devonian-Mississippian stratigraphy on and near the Nevada Test Site: Implications for hydrocarbon potential

    Science.gov (United States)

    Trexler, J.H.; Cole, J.C.; Cashman, P.H.

    1996-01-01

    Paleozoic strata on the Nevada Test Site and surrounding area are affected by the intersection of several important geologic trends, including the early Paleozoic rift margin and the Late Devonian-Early Mississippian Antler orogenic foredeep. Upper Paleozoic strata are lithologically diverse and include siliciclastic sediments (carbonaceous shale, clean quartzose sands, bedded chert, and chert-lithic conglomerate and sand) and various carbonates. These are interpreted to have been deposited in a range of environments and water depths. The resulting complex stratigraphy with its dramatic vertical and lateral changes is difficult to correlate, even between nearby surface and subsurface sections. Our detailed stratigraphic studies on and near the Nevada Test Site show that at least three distinct, and largely coeval, Mississippian facies assemblages can be recognized. When dated, correlated, and restored to their original relative geographic positions, these sections allow a new reconstruction of the Devonian and Mississippian geologic history that includes (1) delineation of the Antler foredeep basin and its clastic fill, (2) description of the muddy marginal shelf that lay inboard of the foredeep, and (3) correlation from that shelf to the outer fringes of the carbonate platform that characterizes the edge of the Mississippian epicontinental sea. The position and delineation of the muddominated marginal shelf environment is particularly important because shales deposited under such conditions elsewhere in the Great Basin are the hydrocarbon source rocks for the Pine Valley and Railroad Valley oil fields. On the Nevada Test Site, Mississippian shale probably generated hydrocarbons in the past, and still has an organic content and a thermal history appropriate for generating hydrocarbons.

  3. Volcano-stratigraphy and Petrography of the Hasandaǧ Volcanites (Central Anatolia)

    Science.gov (United States)

    Zeynep Çalışkanoǧlu, Ayşe; Ünal, Alp; Karadaǧ, Elif; Altunkaynak, Şafak; Görür, Naci

    2016-04-01

    The Hasandaǧ stratovolcano is one of the crucial volcanos within the Cappadocian Volcanic Complex, located in Central Anatolia, Turkey. In Quaternary, it produced various types of volcanic rocks including a variety of lava flows, domes and associated pyroclastic and volcanoclastic rocks. In this study, volcano-stratigraphy and petrography of the volcanic rocks which forms the SE flank of the Hasandaǧ stratovolcano will be presented. The early pyroclastic products associated with plinian-subplinian eruptions cover large areas with different thickness in the region. Felsic pyroclastic rocks are dominant and represented by ash, pumice and pumice-block tuffs and accretionary lapilli tuffs/breccias. Pyroclastic deposits are present as thin layers of reworked tuffs intercalated with sedimentary rocks (mudstone and marl) at the bottom of the volcanic sequence. They interfinger with pyroclastic flow deposits dominated by welded tuff and ignimbrite succession towards the upper parts of the sequence. Andesite- basaltic andesite and basaltic trachy-andesite lavas form the most common lava phase in the region and overlie the pyroclastic succession. At the upper parts of the volcanic succession, basaltic dykes and associated pyroclastic rocks are observed. The youngest member of the volcanic association is represented by andesitic-basaltic andesitic dykes which were injected into basaltic lavas and associated proclastic rocks. The areal distribution of the volcanic rocks in the SE flank of the Hasandaǧ stratovolcano indicates that they were erupted from a number of vents which set parallel to the NW-SE trending major fault systems of Central Anatolia (eg. The Salt Lake Fault). Petrographic investigations indicate that, all lava samples display several textures reflecting disequilibrium crystallization such as different stage of the plagioclase crystallization, sieve texture in plagioclases, clinopyroxene crystals mantled by hornblende (corona texture) and reaction textures

  4. Diatom stratigraphy and long-term dissolved silica concentrations in the Baltic Sea

    Science.gov (United States)

    Olli, Kalle; Clarke, Annemarie; Danielsson, Åsa; Aigars, Juris; Conley, Daniel J.; Tamminen, Timo

    2008-10-01

    In many parts of the world coastal waters with anthropogenic eutrophication have experienced a gradual depletion of dissolved silica (DSi) stocks. This could put pressure on spring bloom diatom populations, e.g. by limiting the intensity of blooms or by causing shifts in species composition. In addition, eutrophication driven enhanced diatom growth is responsible for the redistribution of DSi from the water phase to the sediments, and changes in the growth conditions may be reflected in the sediment diatom stratigraphy. To test for changes in diatom communities we have analyzed four sediment cores from the Baltic Sea covering approximately the last 100 years. The sediment cores originate from the western Gulf of Finland, the Kattegat, the Baltic Proper and the Gulf of Riga. Three out of the four cores reveal only minor changes in composition of diatom assemblages, while the Gulf of Riga core contains major changes, occurring after the second World War. This area is set apart from the other Baltic Sea basins by a high frequency of low after spring bloom DSi concentrations (experiments with cultured T. baltica suggest that intense blooms can potentially exhaust the DSi stock of the water column and exceed the annual Si dissolution in the Gulf of Riga. The phytoplankton time series reveals another exceptional T. baltica bloom period in 1981-1983 (up to 8 mg L - 1 ), which, however, took place before the regular DSi measurements. These periods may be reflected in the conspicuous accumulation of T. baltica frustules in the sediment core corresponding to ca. 1975-1985.

  5. Late Quaternary stratigraphy and sedimentation patterns in the western Arctic Ocean

    Science.gov (United States)

    Polyak, L.; Bischof, J.; Ortiz, J.D.; Darby, D.A.; Channell, J.E.T.; Xuan, C.; Kaufman, D.S.; Lovlie, R.; Schneider, D.A.; Eberl, D.D.; Adler, R.E.; Council, E.A.

    2009-01-01

    Sediment cores from the western Arctic Ocean obtained on the 2005 HOTRAX and some earlier expeditions have been analyzed to develop a stratigraphic correlation from the Alaskan Chukchi margin to the Northwind and Mendeleev-Alpha ridges. The correlation was primarily based on terrigenous sediment composition that is not affected by diagenetic processes as strongly as the biogenic component, and paleomagnetic inclination records. Chronostratigraphic control was provided by 14C dating and amino-acid racemization ages, as well as correlation to earlier established Arctic Ocean stratigraphies. Distribution of sedimentary units across the western Arctic indicates that sedimentation rates decrease from tens of centimeters per kyr on the Alaskan margin to a few centimeters on the southern ends of Northwind and Mendeleev ridges and just a few millimeters on the ridges in the interior of the Amerasia basin. This sedimentation pattern suggests that Late Quaternary sediment transport and deposition, except for turbidites at the basin bottom, were generally controlled by ice concentration (and thus melt-out rate) and transportation distance from sources, with local variances related to subsurface currents. In the long term, most sediment was probably delivered to the core sites by icebergs during glacial periods, with a significant contribution from sea ice. During glacial maxima very fine-grained sediment was deposited with sedimentation rates greatly reduced away from the margins to a hiatus of several kyr duration as shown for the Last Glacial Maximum. This sedimentary environment was possibly related to a very solid ice cover and reduced melt-out over a large part of the western Arctic Ocean.

  6. Simulating the effects of hyperpycnal events on the stratigraphy of Poverty Shelf, New Zealand

    Science.gov (United States)

    Hutton, E. W.; Kettner, A. J.; Kubo, Y.; Gomez, B.; Syvitski, J. P.

    2007-12-01

    The hydrologic-transport model, HydroTrend indicates that suspended sediment discharge of the Waipaoa River, New Zealand increased from 2.3 to 15 Mt/y over the last 3000 years. Prior to the arrival of European colonists in the nineteenth century A.D., volcanic eruptions, natural fires and severe storms controlled erosion rates within the basin. Since then, clearing of much of the indigenous forest for sheep farming has caused suspended sediment discharge of the Waipaoa to increase by 850%. HydroTrend simulations indicate the Waipaoa was not able to generate hyperpycnal discharges before the arrival of European colonists. However, because of deforestation in the headwaters, suspended sediment concentrations of the Waipaoa are now able to exceed 40 kg/m3 during large flood events. The river density of these events is great enough to cause the manner by which sediment is transported from the river to change from a surface plume to a hyperpycnal plume. Although these hyperpycnal events are rare (recurrence intervals greater than 2 years), simulations suggest these events carry approximately one fifth of the total sediment load. Observational data of hyperpycnal flows are scarce as they often only occur during extreme weather events. Given the proper boundary conditions, these events have the potential to transport large amounts of sediment over the sheltered Poverty Bay shelf, and into the deep ocean. For this study, we have used HydroTrend results as input to the basin filling model, sedflux (coupled with the hyperpycnal plume model, sakura), to investigate the impact of these hyperpycnal events on the stratigraphy of the Poverty Bay shelf. We note that while some flood events generate hyperpycnal flows that are able to bypass the shelf, others are unable to ignite and deposit the bulk of their sediment on the shelf.

  7. STRATIGRAPHY OF THE PB-1 WELL, NOPAL I URANIUM DEPOSIT, SIERRA PENA BLANCA, CHIHUAHUA, MEXICO

    Energy Technology Data Exchange (ETDEWEB)

    NA

    2005-06-25

    Three wells, PB-1, PB-2, and PB-3, were drilled in 2003 at the Nopal I uranium deposit as part of a natural analogue study to evaluate radionuclide transport processes. The wells penetrate through the Tertiary volcanic section down to the Cretaceous limestone basement, and intersect the top of the regional aquifer system. The PB-1 well, drilled immediately adjacent to the Nopal I ore body, was cored to a depth of 250 m, thus providing an opportunity to document the local stratigraphy. The uppermost unit encountered in the PB-1 well is the Nopal Formation, a densely welded, crystal-rich rhyolitic ash-flow tuff. The cored section is highly altered and devitrified, with kaolinite, quartz, chlorite, and montmorillonite replacing feldspars and much of the groundmass. Breccia zones within the tuff contain fracture fillings of hematite, limonite, and goethite. A zone of intense clay alteration encountered in the depth interval 17.45-22.30 m was interpreted to represent the basal vitrophyre of this unit. Underlying the basal vitrophyre is the Coloradas Formation, which consists of a welded, lithic-rich rhyolitic ash-flow tuff. The cored section of this unit has undergone devitrification and oxidation, and has a similar alteration mineralogy to that observed in the Nopal tuff. The Nopal I ore body is restricted to a brecciated zone that intersects these two volcanic units. A sharp contact between the Coloradas tuff and the underlying Pozos Formation was observed at a depth of 136.38 m. The Pozos Formation in the PB-1 core consists of interbedded, poorly sorted sandstone and conglomerate layers. The conglomeratic clasts consist of subangular to subrounded fragments of volcanic rocks, limestone, and chert. Thin (2-6 m) intervals of intercalated pumiceous tuffs were observed within this unit. The contact between the Pozos Formation and the underlying Cretaceous limestone basement was observed at a depth of 244.4 m.

  8. Determination of the historical variation of the trophic state in lakes using sediment stratigraphies

    Directory of Open Access Journals (Sweden)

    G. Olli

    2007-11-01

    Full Text Available Biogenic silica (BSi and phosphorous (P accumulation were investigated in sediment cores from Karlskärsviken, a bay of Lake Mälaren. The aim was to make use of BSi and P relations in sediment stratigraphies in order to investigate the historical nutrient trophy in a near shore lake environment since the Middle Ages, with focus on industrial times, and to evaluate anthropogenic influences on the bay's trophic state. The BSi accumulation in the sediments is a better indicator of former nutrient pelagic trophy than P accumulation in sediments and for this reason a BSi inferred P (BSi-P water concentration is calculated. This method enables the determination of the background total phosphorous (TP concentration (which is related to the reference conditions in the investigated bay; this background TP is determined equal to 0.020–0.022 mg L−1. There is an increasing trend of BSi-P concentration in the bay since the Middle Ages to the present, about 0.025 mg L−1, with a small decrease in the inner bay section during the last decades. The P accumulation rate is not found to have changed since the 1960s and 1970s, which indicates that the P loading to Karlskärsviken has not decreased. In Karlskärsviken, the shallow inner section of the bay, where the water quality is dominated by loading from the bay catchment area, is less nutritious than the water in the outer section, which is influenced by the main streams from the western part of Lake Mälaren.

  9. Aeolian stratigraphy describes ice-age paleoenvironments in unglaciated Arctic Alaska

    Science.gov (United States)

    Gaglioti, Benjamin V.; Mann, Daniel H.; Groves, Pamela; Kunz, Michael L.; Farquharson, Louise M.; Reanier, Richard E.; Jones, Benjamin M.; Wooller, Matthew J.

    2018-02-01

    Terrestrial paleoenvironmental records with high dating resolution extending into the last ice age are rare from the western Arctic. Such records can test the synchronicity and extent of ice-age climatic events and define how Arctic landscapes respond to rapid climate changes. Here we describe the stratigraphy and sedimentology of a yedoma deposit in Arctic Alaska (the Carter Section) dating to between 37,000 and 9000 calibrated radiocarbon years BP (37-9 ka) and containing detailed records of loess and sand-sheet sedimentation, soil development, carbon storage, and permafrost dynamics. Alternation between sand-sheet and loess deposition provides a proxy for the extent and activity of the Ikpikpuk Sand Sea (ISS), a large dune field located immediately upwind. Warm, moist interstadial times (ca. 37, 36.3-32.5, and 15-13 ka) triggered floodplain aggradation, permafrost thaw, reduced loess deposition, increased vegetation cover, and rapid soil development accompanied by enhanced carbon storage. During the Last Glacial Maximum (LGM, ca. 28-18 ka), rapid loess deposition took place on a landscape where vegetation was sparse and non-woody. The most intense aeolian activity occurred after the LGM between ca. 18 and 15 ka when sand sheets fringing the ISS expanded over the site, possibly in response to increasingly droughty conditions as summers warmed and active layers deepened. With the exception of this lagged LGM response, the record of aeolian activity at the Carter Section correlates with other paleoenvironmental records from unglaciated Siberia and Alaska. Overall, rapid shifts in geomorphology, soils, vegetation, and permafrost portray an ice-age landscape where, in contrast to the Holocene, environmental change was chronic and dominated by aeolian processes.

  10. Measuring Quality in Inclusive Preschool Classrooms: Development and Validation of the Inclusive Classroom Profile (ICP)

    Science.gov (United States)

    Soukakou, Elena P.

    2012-01-01

    The purpose of this study was to develop and validate an observation measure designed to assess classroom quality in inclusive preschool programs, the Inclusive Classroom Profile (ICP). Developing the rating scale entailed systematic fieldwork in inclusive settings and review of the literature on preschool inclusion. Results from the validation…

  11. An Arendtian perspective on inclusive education

    DEFF Research Database (Denmark)

    Korsgaard, Morten Timmermann

    2016-01-01

    Inclusive education currently appears to be undergoing a crisis and re- examination. This paper presents a new approach to thinking about inclusiveness in the school context. Many positions within inclusive education seem to take political, social and ethical perspectives as a starting point, which...... has allowed inclusive movements and initiatives around the world to succumb to neo-liberal policy-making and has neglected the development of an educational vocabulary that is theoretically and conceptually appropriate for confronting teachers’ central concerns regarding inclusive practices....... The concepts of suspension, bearing with strangers and enlarged thought inspired by Hannah Arendt provide a basis for a re-imagining of inclusive education and for outlining a future school in which inclusiveness is embedded in the very way we think and position ourselves as teachers and pupils...

  12. Prominent features in isotopic, chemical and dust stratigraphies from coastal East Antarctic ice sheet (Eastern Wilkes Land).

    Science.gov (United States)

    Caiazzo, L; Baccolo, G; Barbante, C; Becagli, S; Bertò, M; Ciardini, V; Crotti, I; Delmonte, B; Dreossi, G; Frezzotti, M; Gabrieli, J; Giardi, F; Han, Y; Hong, S-B; Hur, S D; Hwang, H; Kang, J-H; Narcisi, B; Proposito, M; Scarchilli, C; Selmo, E; Severi, M; Spolaor, A; Stenni, B; Traversi, R; Udisti, R

    2017-06-01

    In this work we present the isotopic, chemical and dust stratigraphies of two snow pits sampled in 2013/14 at GV7 (coastal East Antarctica: 70°41' S - 158°51' E, 1950 m a.s.l.). A large number of chemical species are measured aiming to study their potentiality as environmental changes markers. Seasonal cluster backward trajectories analysis was performed and compared with chemical marker stratigraphies. Sea spray aerosol is delivered to the sampling site together with snow precipitation especially in autumn-winter by air masses arising from Western Pacific Ocean sector. Dust show maximum concentration in spring when the air masses arising from Ross Sea sector mobilize mineral dust from ice-free areas of the Transantarctic mountains. The clear seasonal pattern of sulfur oxidized compounds allows the dating of the snow-pit and the calculation of the mean accumulation rate, which is 242 ± 71 mm w.e. for the period 2008-2013. Methanesulfonic acid and NO 3 - do not show any concentration decreasing trend as depth increases, also considering a 12 m firn core record. Therefore these two compounds are not affected by post-depositional processes at this site and can be considered reliable markers for past environmental changes reconstruction. The rBC snow-pit record shows the highest values in summer 2012 likely related to large biomass burning even occurred in Australia in this summer. The undisturbed accumulation rate for this site is demonstrated by the agreement between the chemical stratigraphies and the annual accumulation rate of the two snow-pits analysed in Italian and Korean laboratories. Copyright © 2017 Elsevier Ltd. All rights reserved.

  13. Fiber optic fluid detector

    Science.gov (United States)

    Angel, S. Michael

    1989-01-01

    Particular gases or liquids are detected with a fiber optic element (11, 11a to 11j) having a cladding or coating of a material (23, 23a to 23j) which absorbs the fluid or fluids and which exhibits a change of an optical property, such as index of refraction, light transmissiveness or fluoresence emission, for example, in response to absorption of the fluid. The fluid is sensed by directing light into the fiber optic element and detecting changes in the light, such as exit angle changes for example, that result from the changed optical property of the coating material. The fluid detector (24, 24a to 24j) may be used for such purposes as sensing toxic or explosive gases in the atmosphere, measuring ground water contamination or monitoring fluid flows in industrial processes, among other uses.

  14. Ar-40/Ar-39 laser-probe dating of diamond inclusions from the Premier kimberlite

    Science.gov (United States)

    Phillips, D.; Onstott, T. C.; Harris, J. W.

    1989-01-01

    The results of Ar-40/Ar-39 laser-probe analyses of individual eclogitic clinopyroxene inclusions from Premier diamonds are reported which yield a mean age of 1198 + or - 14 Myr. This age agrees well with Sm-Nd and Ar-40/Ar-39 analyses on similar Premier inclusions and is indistinguishable from the inferred time of emplacement of the host kimberlite, which implies that diamond formation was essentially synchronous with kimberlite generation. The extrapolated nonradiogenic Ar-40/Ar-36 ratio of 334 + or - 102 is similar to the present-day atmospheric composition. This value is inconsistent with Sr and Nd isotopic signatures from Premier eclogite inclusions, which suggest a depleted mantle source. Preentrapment equilibration of the inclusions with an Ar-36-rich fluid is the most probable explanation for the low nonradiogenic composition.

  15. A review of social inclusion measures.

    Science.gov (United States)

    Coombs, Tim; Nicholas, Angela; Pirkis, Jane

    2013-10-01

    Social inclusion is crucial to mental health and well-being and is emphasised in Australia's Fourth National Mental Health Plan. There is a recognition that a measure of social inclusion would complement the suite of outcome measures that is currently used in public sector mental health services. This paper is an initial scope of candidate measures of social inclusion and considers their suitability for this purpose. We identified potential measures through searches of PsycINFO and Medline and a more general Internet search. We extracted descriptive and evaluative information on each measure identified and compared this information with a set of eight criteria. The criteria related to the measure's inclusion of four domains of social inclusion outlined in Australia's Fourth National Mental Health Plan, its usability within the public mental health sector and its psychometric properties. We identified 10 candidate measures of social inclusion: the Activity and Participation Questionnaire (APQ-6); the Australian Community Participation Questionnaire (ACPQ); the Composite Measure of Social Inclusion (CMSI); the EMILIA Project Questionnaire (EPQ); the Evaluating Social Inclusion Questionnaire (ESIQ); the Inclusion Web (IW); the Social and Community Opportunities Profile (SCOPE); the Social Inclusion Measure (SIM); the Social Inclusion Questionnaire (SIQ); and the Staff Survey of Social Inclusion (SSSI). After comparison with the eight review criteria, we determined that the APQ-6 and the SCOPE-short form show the most potential for further testing. Social inclusion is too important not to measure. This discussion of individual-level measures of social inclusion provides a springboard for selecting an appropriate measure for use in public sector mental health services. It suggests that there are two primary candidates, but neither of these is quite fit-for-purpose in their current form. Further exploration will reveal whether one of these is suitable, whether another

  16. Metalworking and machining fluids

    Science.gov (United States)

    Erdemir, Ali; Sykora, Frank; Dorbeck, Mark

    2010-10-12

    Improved boron-based metal working and machining fluids. Boric acid and boron-based additives that, when mixed with certain carrier fluids, such as water, cellulose and/or cellulose derivatives, polyhydric alcohol, polyalkylene glycol, polyvinyl alcohol, starch, dextrin, in solid and/or solvated forms result in improved metalworking and machining of metallic work pieces. Fluids manufactured with boric acid or boron-based additives effectively reduce friction, prevent galling and severe wear problems on cutting and forming tools.

  17. Mathematical Model for Collision-Coalescence Among Inclusions in the Bloom Continuous Caster with M-EMS

    Science.gov (United States)

    Lei, Hong; Jiang, Jimin; Yang, Bin; Zhao, Yan; Zhang, Hongwei; Wang, Weixian; Dong, Guiwen

    2018-02-01

    Mathematical simulation is an effective tool to analyze the fluid flow and the inclusion behavior in the bloom continuous caster with mold electromagnetic stirring (M-EMS). The mathematical model is applied to the modeling of magnetic field, flow field, and inclusion field. Due to the introduction of Archimedes force, the collision mechanism and inclusion's slipping velocity should be modified in the inclusion mass and population conservation model. Numerically predicted magnetic field, flow field, and the inclusion spatial distribution conform to the experimental results in the existing literature. Lorentz force plays an important role in the fluid flow, and Archimedes force plays an important role in the inclusion distribution in the continuous caster. Due to Brownian collision, Stokes collision, Archimedes collision, and turbulent collision, the coalescence among inclusions occurs in the bloom continuous caster with M-EMS. Among the four types of collisions, turbulent collision occurs most frequently, followed by Archimedes collision and Stokes collision. The frequency of Brownian collision is several orders of magnitudes smaller and is therefore negligible. The inclusion volume concentration, number density, and characteristic radius exhibit a U-shape in the continuous caster without M-EMS. However, with M-EMS, they exhibit an inverted U-shape.

  18. Mathematical Model for Collision-Coalescence Among Inclusions in the Bloom Continuous Caster with M-EMS

    Science.gov (United States)

    Lei, Hong; Jiang, Jimin; Yang, Bin; Zhao, Yan; Zhang, Hongwei; Wang, Weixian; Dong, Guiwen

    2018-04-01

    Mathematical simulation is an effective tool to analyze the fluid flow and the inclusion behavior in the bloom continuous caster with mold electromagnetic stirring (M-EMS). The mathematical model is applied to the modeling of magnetic field, flow field, and inclusion field. Due to the introduction of Archimedes force, the collision mechanism and inclusion's slipping velocity should be modified in the inclusion mass and population conservation model. Numerically predicted magnetic field, flow field, and the inclusion spatial distribution conform to the experimental results in the existing literature. Lorentz force plays an important role in the fluid flow, and Archimedes force plays an important role in the inclusion distribution in the continuous caster. Due to Brownian collision, Stokes collision, Archimedes collision, and turbulent collision, the coalescence among inclusions occurs in the bloom continuous caster with M-EMS. Among the four types of collisions, turbulent collision occurs most frequently, followed by Archimedes collision and Stokes collision. The frequency of Brownian collision is several orders of magnitudes smaller and is therefore negligible. The inclusion volume concentration, number density, and characteristic radius exhibit a U-shape in the continuous caster without M-EMS. However, with M-EMS, they exhibit an inverted U-shape.

  19. Evolution of the volcanic plumbing systemof Alicudi (Aeolian Islands - Italy: evidence from fluid and melt inclusionsin quartz xenoliths

    Directory of Open Access Journals (Sweden)

    A. Peccerillo

    2004-06-01

    Full Text Available Quartz-rich xenoliths in lavas (basalts to andesites; 90-30 ka from Alicudi contain abundant melt and fluid inclusions. Two generations of CO2-rich fluid inclusions are present in quartz-rich xenolith grains: early (Type I inclusions related to partial melting of the host xenoliths, and late Type II inclusions related to the fluid trapping during xenolith ascent. Homogenisation temperatures of fluid inclusions correspond to two density intervals: 0.93-0.68 g/cm3 (Type I and 0.47-0.26 g/cm3 (Type II. Early Type I fluid inclusions indicate trapping pressures around 6 kbar, which are representative for the levels of partial melting of crustal rocks and xenolith formation. Late Type II fluid inclusions show lower trapping pressures, between 1.7 kbar and 0.2 kbar, indicative for shallow magma rest and accumulation during ascent to the surface. Data suggest the presence of two magma reservoirs: the first is located at lower crustal depths (about 24 km, site of fractional crystallization, mixing with source derived magma, and various degrees of crustal assimilation. The second magma reservoir is located at shallow crustal depths (about 6 km, the site where magma rested for a short time before erupting.

  20. Electrorheological fluids and methods

    Science.gov (United States)

    Green, Peter F.; McIntyre, Ernest C.

    2015-06-02

    Electrorheological fluids and methods include changes in liquid-like materials that can flow like milk and subsequently form solid-like structures under applied electric fields; e.g., about 1 kV/mm. Such fluids can be used in various ways as smart suspensions, including uses in automotive, defense, and civil engineering applications. Electrorheological fluids and methods include one or more polar molecule substituted polyhedral silsesquioxanes (e.g., sulfonated polyhedral silsesquioxanes) and one or more oils (e.g., silicone oil), where the fluid can be subjected to an electric field.