WorldWideScience

Sample records for flow reed bed

  1. System for the Reduction of Substances in Reject Water from Reed-Bed Sludge Mineralization Plants

    DEFF Research Database (Denmark)

    2004-01-01

    the reject water via recirculation into a mixed reactor and back onto the reed-beds. The mixed rector consists of a container in which sludge (that is typically loaded directly on to reed-beds) is mixed with recirculated reject water from reed-beds. The sludge mixture has a definable hydraulic retention time...... within the container. The solution is then applied to the reed-beds, which dewaters, converts, and partially mineralize the sludge mixture. The reject water from the reed-beds is split where up to100% of the reject water is recirculated back to the mixed reactor and the remaining usually disposed......The invention is a system for the reduction of substances in reject water from reed-bed sludge mineralization plants (also referred to as sludge dewatering reed-beds). The systems utilizes the composition of substances in reject water from reed-beds and that of sludge to reduce substance mass from...

  2. Purification performances of common reed beds based on the ...

    African Journals Online (AJOL)

    SARAH

    2013-11-30

    Nov 30, 2013 ... Objective: This study aims to determine the purification performances of common reed beds in order to facilitate ... water crops. According to the INSAE (2002), Benin had a population of 6 million people in 2000; in 2012, this population would reach 9 million. ..... Physics and Chemistry of the Earth, vol.

  3. Gravity Drainage of Activated Sludge on Reed Beds

    DEFF Research Database (Denmark)

    Christensen, Morten Lykkegaard; Dominiak, Dominik Marek; Keiding, Kristian

    has therefore been developed to measure relevant quality parameters: specific cake resistance, settling velocity and cake compressibility. It has been found that activated sludge form highly compressible cake even at the low compressive pressures obtained during drainage. Numerical simulation shows...... from the wastewater treatment plant to the red beds may destroy the sludge structure and thereby reduces the dewaterability of sludge. Both the mechanical stress during pumping and anaerobic microbial activity affects the sludge quality. The quality of the sludge can be improved if I) the drying reed...... beds are placed close to the wastewater treatment plant, II) anaerobic condition is avoid e.g. by adding calcium nitrate, and III) the sludge structure is rebuild before it is poured on the reed bed e.g. by adding calcium carbonate...

  4. An introduction to constructed wetlands (reed beds) sustainable low cost wastewater treatment plants

    International Nuclear Information System (INIS)

    Ahmad, M.I.

    2005-01-01

    because it is essentially simple, cheap and sustainable. Because they achieve a natural balance, well designed reed bed systems will more or less look after themselves. They do not need much power, they do not need any chemicals, they need very little maintenance, and the water leaving such a system can be very clean - certainly clean enough to pass the National Water Quality Standards. A well designed reed bed system needs both aquatic plants and special water movement. The main plants used is still the Common reed (Pragmatism karaka - Nari), Cattail (Typha australis - Dab) and Vetiver grass (Khus). Almost all these aquatic plants are available in natural wetlands, along rivers, canals, water courses, and water logged areas in Pakistan. The constructed wetlands (Reed Beds) utilize horizontal flow system, vertical flow system or combination of both. The horizontal system includes 'free water surface (FWS)' wetlands and 'vegetated submerged bed (VSB)' wetlands. The vertical system invariably uses VSB system. The required land area depends on the wastewater flow. However, in the rural setting, the horizontal system requires about 1.0 square meter / person (or population equivalent in case of an industry) and the vertical system even less than that. A working reed bed system can be designed as a public area like a park with water cascades, bridges, shallow pools with fish, and small islands for birds. There is no smell. no flies. no noise, no chemicals. and no machines. The only regular maintenance work is harvesting the reeds once a year and occasional weeding (without poisons) There is potential for the combination of reed beds with a methane process in which the bulk of sludge is removed by settlement and fed to a methane digester to produce energy, and the supernatant is then cleaned with reed beds. This may becomes a practical solution for systems in urban areas. In flat areas like large towns can be split up into segments, each served by a separate reed bed system

  5. Does Botanical Diversity in Sewage Treatment Reed-Bed Sites Enhance Invertebrate Biodiversity?

    Directory of Open Access Journals (Sweden)

    Alan Feest

    2012-01-01

    Full Text Available (1 This study examines the effect of increasing botanical diversity, through reed-bed planting and maintenance regimes, on sewage treatment reed-bed invertebrate biodiversity and the possible enrichment of overall catchment biodiversity. (2 Reed-bed invertebrates were identified as a good indicator group of overall site biodiversity quality and were sampled at a range of sewage treatment reed-bed sites in the same geographical area between May and August 2006 (plus one natural reed-bed control site. Standardised water trapping and pitfall trapping techniques were employed throughout this sampling period. (3 Statistical analysis of the sampling results revealed that the number of plant species recorded was inversely related to terrestrial invertebrate species richness, species conservation value index and biomass within the study sites. For example, the natural reed-bed sampled had the highest botanical diversity but the lowest terrestrial invertebrate species richness. (4 This study has demonstrated that sewage treatment reed-beds support a diverse range of invertebrate species, some of them being of national conservation value. This suggests that sewage treatment reed-beds may be at least as biodiverse as naturally occurring reed-beds and will add to the overall biodiversity and ecohydrology of a catchment whilst saving energy.

  6. ADVANCES IN CLOG STATE MONITORING FOR USE IN AUTOMATED REED BED INSTALLATIONS

    Directory of Open Access Journals (Sweden)

    Theodore HUGHES-RILEY

    2014-06-01

    Full Text Available Constructed wetlands are a popular form of waste-water treatment that have proliferated across Europe and the rest of the world in recent years as an environmentally conscious form of waste water treatment. The ability to monitor the conditions in the bed and control input factors such as heating and aeration may extend the lifetime of the reed bed substantially beyond the ten year lifetime normally reached. The Autonomous Reed Bed Installation (ARBI project is an EU FP7 initiative to develop a reed bed with automated control over input parameters based on readings taken from embedded sensors. Automated remedial action may improve bed treatment efficiency, and prolong the life of the bed and avoiding the need to refurbish the bed, which is both time consuming and costly. One critical parameter to observe is the clog state of the reed bed, as this can severely impact on the efficiency of water treatment to the point of the bed becoming non-operable. Magnetic resonance (MR sensors can be a powerful tool in determining clogging levels, and has previously been explored in the literature. This work is based on a conference paper (2nd International Conference "Water resources and wetlands", 2014 and details magnetic sensors suitable for long-term embedding into a constructed wetland. Unlike previous studies this work examines a probe embedded into a wetland.

  7. Organic matter and heavy metals content modeling in sewage sludge treated with reed bed system

    Science.gov (United States)

    Boruszko, Dariusz; Dąbrowski, Wojciech; Malinowski, Paweł

    2017-11-01

    The long process of sludge stabilization (7-15 years) remarkably reduces the organic matter content and causes the process of sludge humifaction. This paper presents the results of using low-cost methods of sludge treatment in the wastewater treatment plant located in Zambrow, Podlaskie Province. The results of studies on the organic matter and heavy metals content in sewage sludge after treatment in a reed bed system are presented. The aim of the research was to evaluate and model organic matter and heavy metals concentrations during sewage stabilization in reed bed lagoons. The lowest concentration, below 1.3 mg/kg DM of the examined seven heavy metals was mercury (Hg). The highest concentration, exceeding 1300 mg/kg DM was zinc (Zn). The obtained results for the heavy metals in sewage sludge from the reed bed lagoons in Zambrow show that the average content of the analyzed heavy metals is approximately 1620 mg/kg DM. The results of the study demonstrate a high efficiency of low-cost methods used in Zambrów WWTP in terms of the quality of the processed sludge. Sewage sludge from the lowest layer of the reed lagoon (12-14 years of dewatering and transformation) is characterized by the lowest organic matter and heavy metals content. The higher a sediment layer lies, i.e. the shorter the time of processing, the higher is the heavy metals content. This indicates a great role of reeds in the accumulation of these compounds.

  8. Development of the reed bed in Matsalu wetland, Estonia: responses to neotectonic land uplift, sea level changes and human influences

    Directory of Open Access Journals (Sweden)

    Mats Meriste

    2015-05-01

    Full Text Available We studied reed bed development in Matsalu wetland and the Kasari River delta, Estonia, since the late 18th century using historical schemes, topographical maps and aerial photographs. Our aim was to understand the mechanisms controlling reed distribution in Matsalu wetland, the largest coastal wetland of the eastern Baltic Sea occupying an area of about 25 km2. Natural development of the reed bed in Matsalu Bay and the Kasari delta is mainly controlled by shoreline displacement due to post-glacial neotectonic land uplift. The dredging of the Kasari delta in the 1920s–1930s caused a rapid seaward migration of reed bed communities due to the dispersal of fragmented rhizomes on the shallow sea bottom and along the canal banks reaching Matsalu Bay, while the landward parts of the former wetland were occupied by meadow communities. The expansion of the reed bed started in between the 1951s and 1970s and a maximum extent of 27 km2 was gained by the late 1970s at the peak of eutrophication. In the last decades the reed bed development has been influenced by sea level rise and increased intensity of cyclonic activity in the Baltic Sea, which has caused the deterioration of the reed bed that was weakened by eutrophication due to nutrient inflow from agricultural landscapes mainly in the 1960s–1980s.

  9. Hydraulic and biochemical analyses on full-scale sludge consolidation reed beds in Tuscany (Italy).

    Science.gov (United States)

    Giraldi, D; Masciandaro, G; Peruzzi, E; Bianchi, V; Peruzzi, P; Ceccanti, B; Iannelli, R

    2009-01-01

    The management of sewage sludge has recently become one of the most significant challenges in wastewater management. Reed bed systems appear to be an efficient and economical solution for sludge management in small wastewater treatment plants. Four years ago, one of the holding companies for water and wastewater in central Italy adopted this technology in 6 wastewater treatment plants. Hydraulic and biochemical analyses were performed on the most representative site to asses the behaviour of reed beds with regard to dewatering, mineralization and humification of disposed sludge. Moreover, daily water content analysis were performed in the interval between subsequent sludge loadings. Results indicated a decrease of sludge volume by about 93% on a yearly basis. Biochemical analysis highlighted that mineralization processes decrease over time due to a rapid decrease of microbial activity and labile substrates, such as DHase enzyme and water-soluble carbon and ammonium, respectively. Moreover, a significant interrelationship between the parameters linked with mineralization was found: after two years of operation, the process of mineralization of organic matter is still predominant in the humification of organic matter. Daily water content data were used to define a semi empirical equation describing the dynamics of the dewatering process. Overall, the use of sludge reed beds resulted feasible, ecologically sustainable and cost-effective.

  10. [Effect of reed rhizosphere on nitrogen and COD removal efficiency in subsurface flow constructed wetlands].

    Science.gov (United States)

    Dai, Yuan-yuan; Yang, Xin-ping; Zhou, Li-xiang

    2008-12-01

    Nitrogen removal efficiency was investigated in three subsurface flow constructed wetlands (CWs) with and without reed. Root bag made of nylon sieve with 300 mesh was used to enwrap the reed root in one of reed CWs to distinguish reed rhizosphere from non-rhizosphere. The CWs with root bag enwrapped reed root (hereinafter called as mesh CWs) and other CWs were fed with artificial ammonium-rich wastewater. The results indicated that the COD and N removal occurred mainly in the front of CWs, and C and nitrogen removal occurred concurrently along the stream way. When C/N ratio of influent was 5, the removal efficiencies of NH4+ -N in control CWs, reed CWs and mesh CWs were 66.2%, 94.2% and 82.2%, respectively. TN removal efficiencies were 67.2%, 90.7% and 76.1% respectively. Simultaneous nitrification and denitrification phenomenon in this study was also observed. The removal efficiency of organic carbon was different from nitrogen removal efficiency, mesh CWs showed the highest COD removal efficiency with 80.9%, while control CWs and reed CWs were 72.2% and 56.2%, respectively. C/N ratio of wastewater throughout the bed was more than 5 in three CWs, which indicated carbon source supply was enough for denitrification. The oxidation-reduction position (ORP) and concentration of total organic carbon in rhizosphere and non-rhizosphere were detected. The ORP in the front of mesh CWs's rhizosphere was much higher than that in control CWs and non-rhizosphere in mesh CWs, which were 11-311 mV and 62-261 mV, respectively. Root exudates also showed the difference between rhizosphere and non-rhizosphere in mesh CWs, the TOC of them were 21.3-54.6 mg x L(-1) and 6.65-12.0 mg x L(-1). Due to the higher ORP and concentration of TOC, the nitrogen removal efficiency in plant CWs was much higher than that in control CWs.

  11. Nitrogen mineralisation and greenhouse gas emission from the soil application of sludge from reed bed mineralisation systems

    DEFF Research Database (Denmark)

    Gómez-Muñoz, B; Larsen, Julie Dam; Bekiaris, G

    2017-01-01

    A sludge treatment reed bed system (STRB) is a technology used for dewatering and stabilising sewage sludge via assisted biological mineralisation, which creates a sludge residue suitable for use as fertiliser on agricultural land. We evaluated the effect of sludge residue storage time (stabilisa......A sludge treatment reed bed system (STRB) is a technology used for dewatering and stabilising sewage sludge via assisted biological mineralisation, which creates a sludge residue suitable for use as fertiliser on agricultural land. We evaluated the effect of sludge residue storage time...

  12. Heavy metal fate in pilot-scale sludge drying reed beds under various design and operation conditions.

    Science.gov (United States)

    Stefanakis, Alexandros I; Tsihrintzis, Vassilios A

    2012-04-30

    Thirteen pilot-scale sludge drying reed bed (SDRB) units have been constructed and operated under various settings. The beds included a cobbles lower layer, where perforated PVC aeration tubes were placed, and two gravel layers on top. The setup included planted beds with common reeds and control units. Three sludge loading rates (SLR) were examined: 30, 60 and 75 kg dm/m(2)/yr. Heavy metal (HM) accumulation in the residual sludge layer was negligible or low, and was found to increase with sludge layer depth. Plant uptake was low; the belowground biomass accumulated significantly more HMs compared to the aboveground biomass. Less than 16% of the influent HM left the bed through drainage. HM accumulation in the gravel layer was the major metal sink in the mass balance. On the whole, the HM content of the residual sludge was below the legal limits proposed by the EU for land application. Copyright © 2012 Elsevier B.V. All rights reserved.

  13. Environmental Assessment of Sewage Sludge Management – Focusing on Sludge Treatment Reed Bed Systems

    DEFF Research Database (Denmark)

    Larsen, Julie Dam

    ; however, in the late 1980s, sludge treatment reed bed (STRB) systems were intro-duced in Denmark and in 2016, more than 100 STRB systems were operating in the country. Sludge treatment in STRB systems is often considered more environmentally friendly compared to mechanical sludge treatment technologies......, albeit only a few life cycle assess-ments (LCAs) comparing the environmental performances of sludge treatment technologies include STRB systems. Furthermore, as data on the STRB system technology suitable for LCA are scarce, the results of these LCAs are unreliable. The project aimed at generating data...... in treated sludge when applied to the land. The overall goal of the project was to perform an LCA comparing the environmental performance of the STRB system technology with a conventional technology based on mechanical dewatering of sludge on a decanter centrifuge and subsequent storage. Geographically...

  14. Gas composition of sludge residue profiles in a sludge treatment reed bed between loadings

    DEFF Research Database (Denmark)

    Larsen, Julie Dam; Nielsen, Steen M; Scheutz, Charlotte

    2017-01-01

    Treatment of sludge in sludge treatment reed bed systems includes dewatering and mineralization. The mineralization process, which is driven by microorganisms, produces different gas species as by-products. The pore space composition of the gas species provides useful information on the biological...... processes occurring in the sludge residue. In this study, we measured the change in composition of gas species in the pore space at different depth levels in vertical sludge residue profiles during a resting period of 32 days. The gas composition of the pore space in the sludge residue changed during...... the resting period. As the resting period proceeded, atmospheric air re-entered the pore space at all depth levels. The methane (CH4) concentration was at its highest during the first part of the resting period, and then declined as the sludge residue became more dewatered and thereby aerated. In the pore...

  15. Large scale application of French reed beds: municipal wastewater treatment for a 20,000 inhabitant's town in Moldova.

    Science.gov (United States)

    Masi, F; Bresciani, R; Martinuzzi, N; Cigarini, G; Rizzo, A

    2017-07-01

    A two-stage vertical flow treatment wetlands system (French reed beds) was realized in 2012-2013 for the Orhei's town in Moldova. The treatment system occupies a total area of about 5 ha and operates in cold climate conditions during winter, with air temperatures below -20 °C. The first 2 years (2013-2015) of treatment performances for this system are presented here, with a particular highlight on the analysis of the commissioning phase and the operative choices taken along this period basing on the observed results. The specific classification of this application of constructed wetlands (CWs) for the primary and secondary treatment of municipal wastewater as a medium-large size system makes this technical report a relevant reference for demonstrating the possible extension to the highest numbers of inhabitants for the common application range of this family of technologies (CWs) for municipal wastewater. The observed performances for organic carbon (both as chemical oxygen demand (COD) and biochemical oxygen demand (BOD 5 )), suspended solids and ammonia removals in the whole first operational period consistently satisfied the national limits for discharge in rivers, respectively, with average values of 86%, 96% and 66%. The treated daily flow was measured in the range of 1,000-2,000 m 3 /d.

  16. Life cycle assessment comparing the treatment of surplus activated sludge in a sludge treatment reed bed system with mechanical treatment on centrifuge

    DEFF Research Database (Denmark)

    Larsen, Julie Dam; Hoeve, Marieke ten; Nielsen, Steen

    2018-01-01

    In Denmark, the conventional method for treating sewage sludge is mechanical dewatering and subsequent storage. However, sludge treatment reed bed systems, which are holistic sludge treatment facilities combining the dewatering, mineralisation and storage of sludge, have been more common during...... the last three decades. Treatment of sludge in a sludge treatment reed bed system can be combined with post-treatment (further dewatering and mineralisation) on a stockpile area. This study aimed to compare the environmental performances of a mechanical sludge treatment method with the sludge treatment...... reed bed system strategy, using the life cycle assessment approach and a life cycle inventory based on newly generated data obtained from Danish reference facilities. The scenarios based on the different treatment methods were initiated by sludge entering the sludge treatment reed bed system...

  17. Full Scale Sludge Treatment in Reed Beds in Moderate Climate—A Case Study

    Directory of Open Access Journals (Sweden)

    Artur Mennerich

    2017-09-01

    Full Text Available The wastewater treatment plant of Wathlingen, Germany, has a design capacity of 20,500 p.e. Since 2000, the sewage sludge has been treated in four reed beds with an area of 3000 m2 each. During this time, three of the four polders were emptied once and put into operation again, which has allowed for an evaluation of complete operation cycles from startup to sludge removal. This paper comprises data on polder construction and operating results as well as an economic evaluation of construction, operation, and sludge disposal costs. Results show that sludge DS mass may be reduced by at least 23% and at most 52%. Water content was reduced, but the DS concentration of the product excavated was not higher than around 20% DS. Operation experiences proved that the system is very user-friendly and requiring limited maintenance and control work. To make the best use of this technique, it is recommended a separate area for additional storage and dewatering is provided after the sludge from the polders is removed. This allows for the possibility for the operators to determine the appropriate time and conditions for final disposal.

  18. Evaluation of Green-LiDAR Data for Mapping Extent, Density and Height of Aquatic Reed Beds at Lake Chiemsee, Bavaria—Germany

    Directory of Open Access Journals (Sweden)

    Nicolás Corti Meneses

    2017-12-01

    Full Text Available Aquatic reed is an important indicator for the ecological assessment of freshwater lakes. Monitoring is essential to document its expansion or deterioration and decline. The applicability of Green-LiDAR data for the status assessment of aquatic reed beds of Bavarian freshwater lakes was investigated. The study focused on mapping diagnostic structural parameters of aquatic reed beds by exploring 3D data provided by the Green-LiDAR system. Field observations were conducted over 14 different areas of interest along 152 cross-sections. The data indicated the morphologic and phenologic traits of aquatic reed, which were used for validation purposes. For the automatic classification of aquatic reed bed spatial extent, density and height, a rule-based algorithm was developed. LiDAR data allowed for the delimitating of the aquatic reed frontline, as well as shoreline, and therefore an accurate quantification of extents (Hausdorff distance = 5.74 m and RMSE of cross-sections length 0.69 m. The overall accuracy measured for aquatic reed bed density compared to the simultaneously recorded aerial imagery was 96% with a Kappa coefficient of 0.91 and 72% (Kappa = 0.5 compared to field measurements. Digital Surface Models (DSM, calculated from point clouds, similarly showed a high level of agreement in derived heights of flat surfaces (RMSE = 0.1 m and showed an adequate agreement of aquatic reed heights with evenly distributed errors (RMSE = 0.8 m. Compared to field measurements, aerial laser scanning delivered valuable information with no disturbance of the habitat. Analysing data with our classification procedure improved the efficiency, reproducibility, and accuracy of the quantification and monitoring of aquatic reed beds.

  19. Reed beds receiving industrial sludge containing nitroaromatic compounds. Effects of outgoing water and bed material extracts in the umu-c genotoxicity assay, DR-CALUX assay and on early life stage development in zebrafish (Danio rerio).

    Science.gov (United States)

    Gustavsson, Lillemor; Hollert, Henner; Jonsson, Sofie; van Bavel, Bert; Engwall, Magnus

    2007-05-01

    Sweden has prohibited the deposition of organic waste since January, 2005. Since 1 million tons of sludge is produced every year in Sweden and the capacity for incineration does not fill the demands, other methods of sludge management have to be introduced to a larger degree. One common method in the USA and parts of Europe is the use of wetlands to treat wastewater and sewage sludge. The capacity of reed beds to affect the toxicity of a complex mixture of nitroaromatics in sludge, however, is not fully elucidated. In this study, an industrial sludge containing explosives and pharmaceutical residues was therefore treated in artificial reed beds and the change in toxicity was studied. Nitroaromatic compounds, which are the main ingredients of many pharmaceuticals and explosives, are well known to cause cytotoxicity and genotoxicity. Recently performed studies have also showed that embryos of zebrafish (Danio rerio) are sensitive to nitroaromatic compounds. Therefore, we tested the sludge passing through constructed wetlands in order to detect any changes in levels of embryotoxicity, genotoxicity and dioxin-like activity (AhR-agonists). We also compared unplanted and planted systems in order to examine the impact of the root system on the fate of the toxicants. An industrial sludge containing a complex mixture of nitroaromatics was added daily to small-scale constructed wetlands (vertical flow), both unplanted and planted with Phragmites australis. Sludge with an average dry weight of 1.25%, was added with an average hydraulic loading rate of 1.2 L/day. Outgoing water was collected daily and stored at -20 degrees C. The artificial wetland sediment was Soxhlet extracted, followed by clean-up with multi-layer silica, or extracted by ultrasonic treatment, yielding one organic extract and one water extract of the same sample. Genotoxicity of the extracts was measured according to the ISO protocol for the umu-C genotoxicity assay (ISO/TC 147/SC 5/ WG9 N8), using

  20. Habitat selection of two Acrocephalus warblers breeding in reed beds near Malacky (Western Slovakia)

    Czech Academy of Sciences Publication Activity Database

    Prokešová, Jarmila; Kocian, Ľ.

    2004-01-01

    Roč. 59, č. 5 (2004), s. 637-644 ISSN 0006-3088 Grant - others:VEGA(SK) 1/7197/20; VEGA(SK) 1/0017/03 Institutional research plan: CEZ:AV0Z6093917 Keywords : reed warblers * breeding * habitat selection Subject RIV: EH - Ecology, Behaviour Impact factor: 0.207, year: 2004 http://biologia.savba.sk/59_5_04/Prokesova_J.pdf

  1. Flow characteristics of counter-current flow in debris bed

    International Nuclear Information System (INIS)

    Abe, Yutaka; Adachi, Hiromichi

    2004-01-01

    In the course of a severe accident, a damaged core would form a debris bed consisting of once-molten and fragmented fuel elements. It is necessary to evaluate the dryout heat flux for the judgment of the coolability of the debris bed during the severe accident. The dryout phenomena in the debris bed is dominated by the counter-current flow limitation (CCFL) in the debris bed. In this study, air-water counter-current flow behavior in the debris bed is experimentally investigated with glass particles simulating the debris beds. In this experiment, falling water flow rate and axial pressure distributions were experimentally measured. As the results, it is clarified that falling water flow rate becomes larger with the debris bed height and the pressure gradient in the upper region of the debris bed is different from that in the lower region of the debris bed. These results indicate that the dominant region for CCFL in the debris bed is identified near the top of the debris bed. Analytical results with annular flow model indicates that interfacial shear stress in the upper region of the debris bed is larger than that in the lower region of the debris bed. (author)

  2. Greenhouse gas emissions from the mineralisation process in a Sludge Treatment Reed Bed system: Seasonal variation and environmental impact

    DEFF Research Database (Denmark)

    Larsen, Julie Dam; Nielsen, Steen; Scheutz, Charlotte

    2017-01-01

    Greenhouse gas emission data from the mineralisation process in Sludge Treatment Reed Bed systems (STRB) are scarce. The aim of this study was to quantify the emission rates of carbon dioxide (CO2), methane (CH4) and nitrous oxide (N2O) and to investigate seasonal variations in order to estimate...... the annual greenhouse gas emission rate of the mineralisation process. The full-scale STRB at Helsinge wastewater treatment plant (WWTP) in Denmark was chosen as the study site. Gas emission rates were measured using static surface flux chambers. The measurements were carried out in October/November 2014......, March/April 2015, June/July 2015 and January/February 2016. We found that the emission rates of all included gas species were significantly affected by season. For CO2 and CH4, the highest emission rates were recorded in summer, being138 and 5.2 g m−2 d−1, respectively, while the lowest rates were...

  3. Nonlinear flow response of soft hair beds

    Science.gov (United States)

    Alvarado, José

    2017-11-01

    We are hairy inside: beds of passive fibers anchored to a surface and immersed in fluids are prevalent in many biological systems, including intestines, tongues, and blood vessels. Such hairs are soft enough to deform in response to stresses from fluid flows. Fluid stresses are in turn affected by hair deformation, leading to a coupled elastoviscous problem which is poorly understood. Here we investigate a biomimetic model system of elastomer hair beds subject to shear- driven Stokes flows. We characterize this system with a theoretical model which accounts for the large-deformation flow response of hair beds. Hair bending results in a drag-reducing nonlinearity because the hair tip lowers toward the base, widening the gap through which fluid flows. When hairs are cantilevered at an angle subnormal to the surface, flow against the grain bends hairs away from the base, narrowing the gap. The flow response of angled hair beds is axially asymmetric and amounts to a rectification nonlinearity. We identify an elastoviscous parameter which controls nonlinear behavior. Our study raises the hypothesis that biological hairy surfaces function to reduce fluid drag. Furthermore, angled hairs may be incorporated in the design of integrated microfluidic components, such as diodes and pumps. J.A. acknowledges support the U. S. Army Research Office under Grant Number W911NF-14-1-0396.

  4. Influences of wind flow on stopover decisions: the case of the reed warbler Acrocephalus scirpaceus in the Western Mediterranean

    Science.gov (United States)

    Barriocanal, C.; Montserrat, D.; Robson, D.

    2002-06-01

    Wind directions measured at two different heights (850 hPa and 700 hPa) and at different hours of the night were analysed during the spring migration passage at a bird stopover site located in the western Mediterranean, in order to evaluate the importance of wind components for a stopover decision. From a huge ringing campaign of bird migration in north-east Spain, data from the reed warbler Acrocephalus scirpaceus have been used for the analysis. From a total of 2,478 reed warblers captured between 1993 and 1997 data recording significant days, with a high number of captures, and decrease days, with few captures, have been selected to develop an analysis of wind direction in relation to stopover and flight resumption. On days with a high capture the winds had mainly a fourth-quadrant flow (from the north, north-west and west), these being mainly head winds. Winds with westerly component (from the north-west, west and south-west), which enhance the flight, account for the majority of the days when there was a low capture of reed warblers. Wind direction therefore appears to be a determining factor for stopover decisions and resumption of flight for the reed warblers at an intermediate stage of their spring migration where topographical characteristics govern the winds.

  5. Removal of personal care compounds from sewage sludge in reed bed container (lysimeter) studies - Effects of macrophytes

    DEFF Research Database (Denmark)

    Chen, Xijuan; Pauly, Udo; Rehfus, Stefan

    2009-01-01

    as on the bactericide Triclosan. Additionally, the capacity of different macrophytes species to affect the treatment process was examined. Three different macrophyte species were compared: bulrush (Typha latifolia), reed (Phragmites australis) and reed canary grass (Phalaris arundinacea). They were planted...... into containers (lysimeters) with a size of 1 m × 1 m × 1 m which were filled with 20 cm gravel at the bottom and 50 cm sludge on top, into which the macrophytes were planted. During the twelve months experiment reduction of 20-30% for HHCB and AHTN, 70% for Triclosan and 70% for OTNE were determined under...

  6. Experimental study of flow field characteristics on bed configurations in the pebble bed reactor

    International Nuclear Information System (INIS)

    Jia, Xinlong; Gui, Nan; Yang, Xingtuan; Tu, Jiyuan; Jia, Haijun; Jiang, Shengyao

    2017-01-01

    Highlights: • PTV study of flow fields of pebble bed reactor with different configurations are carried out. • Some criteria are proposed to quantify vertical velocity field and flow uniformity. • The effect of different pebble bed configurations is also compared by the proposed criteria. • The displacement thickness is used analogically to analyze flow field characteristics. • The effect of mass flow variation in the stagnated region of the funnel flow is measured. - Abstract: The flow field characteristics are of fundamental importance in the design work of the pebble bed high temperature gas cooled reactor (HTGR). The different effects of bed configurations on the flow characteristics of pebble bed are studied through the PTV (Particle Tracking Velocimetry) experiment. Some criteria, e.g. flow uniformity (σ) and mass flow level (α), are proposed to estimate vertical velocity field and compare the bed configurations. The distribution of the Δθ (angle difference between the individual particle velocity and the velocity vector sum of all particles) is also used to estimate the resultant motion consistency level. Moreover, for each bed configuration, the thickness of displacement is analyzed to measure the effect of the funnel flow zone based on the boundary layer theory. Detailed information shows the quantified characteristics of bed configuration effects on flow uniformity and other characteristics; and the sequence of levels of each estimation criterion is obtained for all bed configurations. In addition, a good design of the pebble bed configuration is suggested and these estimation criteria can be also applied and adopted in testing other geometry designs of pebble bed.

  7. Effect of bed configuration on pebble flow uniformity and stagnation in the pebble bed reactor

    Energy Technology Data Exchange (ETDEWEB)

    Gui, Nan; Yang, Xingtuan [Institute of Nuclear and New Energy Technology of Tsinghua University, Key Laboratory of Advanced Reactor Engineering and Safety, Ministry of Education, Beijing 100084 (China); Tu, Jiyuan [Institute of Nuclear and New Energy Technology of Tsinghua University, Key Laboratory of Advanced Reactor Engineering and Safety, Ministry of Education, Beijing 100084 (China); School of Aerospace, Mechanical and Manufacturing Engineering, RMIT University, Melbourne, VIC 3083 (Australia); Jiang, Shengyao, E-mail: jiangshy@tsinghua.edu.cn [Institute of Nuclear and New Energy Technology of Tsinghua University, Key Laboratory of Advanced Reactor Engineering and Safety, Ministry of Education, Beijing 100084 (China)

    2014-04-01

    Highlights: • Pebble flow uniformity and stagnation characteristics are very important for HTR-PM. • Arc- and brachistochrone-shaped configuration effects are studied by DEM simulation. • Best bed configurations with uniform flow and no stagnated pebbles are suggested. • Detailed quantified characteristics of bed configuration effects are shown for explanation. - Abstract: Pebble flow uniformity and stagnation characteristics are very important for the design of pebble bed high temperature gas-cooled reactor. Pebble flows inside some specifically designed contraction configurations of pebble bed are studied by discrete element method. The results show the characteristics of stagnation rates, recycling rates, radial distribution of pebble velocity and residence time. It is demonstrated clearly that the bed with a brachistochrone-shaped configuration achieves optimum levels of flow uniformity and recycling rate concentration, and almost no pebbles are stagnated in the bed. Moreover, the optimum choice among the arc-shaped bed configurations is demonstrated too. Detailed information shows the quantified characteristics of bed configuration effects on flow uniformity. In addition, a good design of the pebble bed configuration is suggested.

  8. Interaction of Ice Stream Flow with Heterogeneous Beds, Version 1

    Data.gov (United States)

    National Aeronautics and Space Administration — This data set consists of outputs of several numerical models simulating ice stream flow over undulated bed, interaction of ice stream flow, and subglacial and...

  9. Flow fields, bed shear stresses, and suspended bed sediment dynamics in bifurcations of a large river

    Science.gov (United States)

    Szupiany, R. N.; Amsler, M. L.; Hernandez, J.; Parsons, D. R.; Best, J. L.; Fornari, E.; Trento, A.

    2012-11-01

    Channel bifurcations associated with bars and islands are important nodes in braided rivers and may control flow partitioning and thus affect downstream confluences, as well as the formation and dynamics of bars. However, the morphodynamic processes associated with bar formation are poorly understood, and previous studies have largely concerned laboratory experiments, small natural streams, or numerical analyses with large Froude numbers, high slopes, and low Shields stresses. In these cases, the morphologic changes at bifurcations are relatively rapid, with predominant bed load transport and the suspended load playing a minor role. In this paper, the evolution of the flow structure and suspended bed sediment transport along four expansion-diffluence units in the Rio Paraná, Argentina, are described. The Rio Paraná is a large multichannel river with a bed composed of medium and fine sands and possesses low Froude numbers and high suspended bed material transport. Primary and secondary flow velocity components were measured with an acoustic Doppler current profiler (ADCP) along the expansion-diffluence units, and the backscatter signal of the ADCP was calibrated to allow simultaneous measurements of suspended bed sediment concentrations. The interactions between these variables show that the cores of primary flow velocity and suspended bed sediment concentration do not necessarily follow the thalweg at the bifurcation and that inertial effects on the suspended bed sediment may influence the morphodynamics of bar formation. It is suggested that changes in flow stage, as well as the presence of vegetation, may further increase the deposition of suspended bed sediment at the bar head. This study suggests that the ratio of suspended bed material to bed load is an important factor controlling the morphodynamics of bifurcations in large sand bed braided rivers.

  10. Effects of bed-load movement on flow resistance over bed forms

    Indian Academy of Sciences (India)

    Abstract. The effect of bed-load transport on flow resistance of alluvial channels with undulated bed was experimentally investigated. The experiments were carried out in a tilting flume 250mm wide and 12·5m long with glass-sides of rectan- gular cross-section and artificial dune shaped floor that was made from Plexi-glass.

  11. French Reed Bed as a Solution to Minimize the Operational and Maintenance Costs of Wastewater Treatment from a Small Settlement: An Italian Example

    Directory of Open Access Journals (Sweden)

    Anacleto Rizzo

    2018-02-01

    Full Text Available French Reed Bed (FRB is a particular constructed wetland (CW solution which receives raw wastewater. Data from the full-scale FRB wastewater treatment plant of Castelluccio di Norcia (center of Italy were collected to show the FRB capability to minimize the operational and management (O&M costs. The system was designed to treat wastewater variable from 200 person equivalent (PE in off-season up to 1000 PE. Data from 2014 up to 2016 showed high removal efficiency in line with French experiences with FRBs. An interview was conducted with the Water Utility to estimate the operational and maintenance (O&M costs faced by the WWTP, which allowed us to detail the O&M costs for energy consumption, water quality samples, and personnel for inspection. Other O&M expenditure items were estimated on the basis of parametric costs from the executive design. The FRB O&M costs in euro for 500–1000 PE (6–11 € PE−1 year−1 resulted from 5 to 13 lower in comparison to those reported for classical activated sludge systems in an Italian context (45–90 € year−1. The low O&M costs are mainly due to the limited energy consumed and to the minimized costs of sludge management.

  12. Fluid flow with heat transfer in a fix-bed

    International Nuclear Information System (INIS)

    Gasparetto, C.A.

    1982-01-01

    Tests with two different fluids, water and air, flowing in a bed with irregular particles of silica were done. The bed was confined inside a tube, which was heated by an external jacket. The bed is characterized by permeability and porosity. The tests showed a wall effect face to the relation between the tube diameter and the medium dimension of the particles. The results are presented as a relation between Nusselt number / Peclet number. (E.G.) [pt

  13. Numerical simulation of flow in fluidized beds

    Czech Academy of Sciences Publication Activity Database

    Bauer, Petr; Beneš, M.; Fučík, R.; Dieu, H.H.; Klement, V.; Máca, R.; Mach, J.; Oberhuber, T.; Strachota, P.; Žabka, V.; Havlena, V.

    2015-01-01

    Roč. 8, č. 5 (2015), s. 833-846 ISSN 1937-1632 Institutional support: RVO:61388998 Keywords : Navier-Stokes equations * multi- phase flow * combustion * turbulence * reactive flow s Subject RIV: BK - Fluid Dynamics Impact factor: 0.737, year: 2015

  14. Deleterious Thermal Effects Due To Randomized Flow Paths in Pebble Bed, and Particle Bed Style Reactors

    Science.gov (United States)

    Moran, Robert P.

    2013-01-01

    A review of literature associated with Pebble Bed and Particle Bed reactor core research has revealed a systemic problem inherent to reactor core concepts which utilize randomized rather than structured coolant channel flow paths. For both the Pebble Bed and Particle Bed Reactor designs; case studies reveal that for indeterminate reasons, regions within the core would suffer from excessive heating leading to thermal runaway and localized fuel melting. A thermal Computational Fluid Dynamics model was utilized to verify that In both the Pebble Bed and Particle Bed Reactor concepts randomized coolant channel pathways combined with localized high temperature regions would work together to resist the flow of coolant diverting it away from where it is needed the most to cooler less resistive pathways where it is needed the least. In other words given the choice via randomized coolant pathways the reactor coolant will take the path of least resistance, and hot zones offer the highest resistance. Having identified the relationship between randomized coolant channel pathways and localized fuel melting it is now safe to assume that other reactor concepts that utilize randomized coolant pathways such as the foam core reactor are also susceptible to this phenomenon.

  15. Flow resistance in a compound gravel-bed bend

    Indian Academy of Sciences (India)

    The parabolic law is the most effective method for the ... training problems. Fluid mixing between the center and sides of a bed is greater than that in a straight channel. The primary reason for this difference is that the shear stress ... The flow measurements were taken at eight consecutive cross-sections of five velocity.

  16. Interaction of slurry pipe flow with a stationary bed

    Czech Academy of Sciences Publication Activity Database

    Matoušek, Václav

    2007-01-01

    Roč. 107, č. 6 (2007), s. 365-372 ISSN 0038-223X R&D Projects: GA ČR GA103/06/0428 Institutional research plan: CEZ:AV0Z20600510 Keywords : sheet flow * particle dispersion * suspension * concentration profile * bed shear stress Subject RIV: BK - Fluid Dynamics Impact factor: 0.108, year: 2007

  17. Measurement of reed valve kinematics

    Directory of Open Access Journals (Sweden)

    Fenkl Michael

    2016-01-01

    Full Text Available The measurement of key kinematic parameters of a reed valve movement is necessary for the further development of the reed valve system. These parameters are dependent on the geometry and material properties of the valve. As they directly affect the quantity of air flowing around the valve, a simple and easy to implement measurement of various valve configuration based on the air flow has been devised and is described in this paper, along with its technical parameters and drawbacks when evaluating reed valves used in reciprocating air compressors. Results are presented for a specimen of a compressor under examination. All kinematic parameters, and timing of the opening and closing of the valve, obtained from the measurement are presented and discussed.

  18. Effect of a flow-corrective insert on the flow pattern in a pebble bed reactor

    Energy Technology Data Exchange (ETDEWEB)

    Li, Yu; Gui, Nan; Yang, Xingtuan [Institute of Nuclear and New Energy Technology, Collaborative Innovation Center of Advanced Nuclear Energy Technology, Key Laboratory of Advanced Reactor Engineering and Safety of Ministry of Education, Tsinghua University, Beijing 100084 (China); Tu, Jiyuan [Institute of Nuclear and New Energy Technology, Collaborative Innovation Center of Advanced Nuclear Energy Technology, Key Laboratory of Advanced Reactor Engineering and Safety of Ministry of Education, Tsinghua University, Beijing 100084 (China); School of Aerospace, Mechanical & Manufacturing Engineering, RMIT University, Melbourne 3083, VIC (Australia); Jiang, Shengyao, E-mail: shengyaojiang@sina.com [Institute of Nuclear and New Energy Technology, Collaborative Innovation Center of Advanced Nuclear Energy Technology, Key Laboratory of Advanced Reactor Engineering and Safety of Ministry of Education, Tsinghua University, Beijing 100084 (China)

    2016-04-15

    Highlights: • Effect of an insert on improving flow uniformity and eliminating stagnant zone is studied. • Three values concerned with the stagnant zone, radial uniformity and flow sequence are used. • Outlet diameter is a critical parameter that determines balancing mechanism of the insert. • Height/location is varied to let the insert work in unbalanced region and avoid adverse effect. - Abstract: A flow-corrective insert is adopted in the pebble-bed high temperature gas-cooled reactor (HTGR) to improve flow performance of the pebble flow for the first time. 3D discrete element method (DEM) modeling is employed to study this slow and dense granular flow. It is verified that locating a properly designed insert in the bed can help transform unsatisfactory flow field to the preferred flow pattern for pebble bed reactors. Three characteristic values on the stagnant zone, radial uniformity and flow sequence of pebble flow are defined to evaluate uniformity of the overall flow field quantitatively. The results demonstrate that the pebble bed equipped with an insert performs better than normal beds from all these three aspects. Moreover, based on numerical experiments, several universal tips for insert design on height, location and outlet diameter are suggested.

  19. Effect of a flow-corrective insert on the flow pattern in a pebble bed reactor

    International Nuclear Information System (INIS)

    Li, Yu; Gui, Nan; Yang, Xingtuan; Tu, Jiyuan; Jiang, Shengyao

    2016-01-01

    Highlights: • Effect of an insert on improving flow uniformity and eliminating stagnant zone is studied. • Three values concerned with the stagnant zone, radial uniformity and flow sequence are used. • Outlet diameter is a critical parameter that determines balancing mechanism of the insert. • Height/location is varied to let the insert work in unbalanced region and avoid adverse effect. - Abstract: A flow-corrective insert is adopted in the pebble-bed high temperature gas-cooled reactor (HTGR) to improve flow performance of the pebble flow for the first time. 3D discrete element method (DEM) modeling is employed to study this slow and dense granular flow. It is verified that locating a properly designed insert in the bed can help transform unsatisfactory flow field to the preferred flow pattern for pebble bed reactors. Three characteristic values on the stagnant zone, radial uniformity and flow sequence of pebble flow are defined to evaluate uniformity of the overall flow field quantitatively. The results demonstrate that the pebble bed equipped with an insert performs better than normal beds from all these three aspects. Moreover, based on numerical experiments, several universal tips for insert design on height, location and outlet diameter are suggested.

  20. Thermal Distribution in Axial-Flow Fixed Bed with Flowing Gas

    OpenAIRE

    Kun Lei; Hongfang Ma; Haitao Zhang; Weiyong Ying; Dingye Fang

    2013-01-01

    This paper reported an experimental research of steady-state heat transfer behaviour of a gas flowing through a fixed bed under the different operating conditions. Studies had been carried out in a fixed-bed packed methanol synthesis catalyst percolated by air at appropriate flow rate. Both radial and axial direction temperature distribution had been investigated under the different operating conditions. The effects of operating conditions including the reactor inlet air ...

  1. Soil microbial activities and solid-state {sup 1}3 CNMR to asses organic matter transformation in a reed-bed under cheese-dairy farm effluents

    Energy Technology Data Exchange (ETDEWEB)

    Farnet, A. M.; Prudent, P.; Ziarelli, F.; Domeizel, M.; Gros, R.

    2009-07-01

    In this study, we described the soil microbial activities involved in a small dairy effluent purification using a reed filter under a Mediterranean climate. We tested whether certain enzyme activities used as bio indicators of dairy waste degradation ({beta}-galactosidase and protease), vary through time which might influence organic matter degradation and to test whether specific microbial communities were selected at the contact of the effluent using community level catabolic profiles (CLCPs). (Author)

  2. Magnetohydraulic flow through a packed bed of electrically conducting spheres

    International Nuclear Information System (INIS)

    Sanders, T.L.

    1985-01-01

    The flow of an electrically conducting fluid through a packed bed of electrically conducting spheres in the presence of a strong magnetic field constitutes a very complex flow situation due to the constant turning of the fluid in and out of magnetic field lines. The interaction of the orthogonal components of the velocity and magnetic field will induce electric fields that are orthogonal to both and the electric fields in turn can cause currents that interact with the magnetic field to generate forces against the direction of flow. The strengths of these generated forces depend primarily upon the closure paths taken by the induced currents which, in turn, depend upon the relative ratio of the electrical resistance of the solid spheres to that of the fluid. Both experimental and analytical analyses of the slow flow of a eutectic mixture of sodium and potassium (NaK) through packed cylinders containing stainless steel spheres in the presence of a strong transverse magnetic field were completed. A theory of magnetohydraulic flow is developed by analogy with the development of hydraulic radius theories of flow through porous media. An exact regional analysis is successfully applied to an infinite bed of electrically conducting spheres with a conducting or non-conducting constraining wall on one side. The equations derived are solved for many different combinations of flowrate, magnetic field strength, porosity, and electrical resistance ratio

  3. Flow and sediment dynamics in bed discordant channel confluences

    OpenAIRE

    Blanckaert, Koen; Leite Ribeiro, Marcelo; Schleiss, Anton

    2011-01-01

    Confluences between small steep tributaries with dominant supply of poorly sorted sediment and larger main channels with dominant flow supply, which are characterized by a pronounced bed discordance, have not yet been considered in the literature. The hydro-morpho-sedimentary processes in such confluences are not well described by existing conceptual models of confluence dynamics. Examples of such confluences on the Upper Rhone River, Switzerland, served as prototype for the reported laborato...

  4. Biofilm effect on flow structure over a permeable bed

    Science.gov (United States)

    Kazemifar, Farzan; Blois, Gianluca; Aybar, Marcelo; Perez-Calleja, Patricia; Nerenberg, Robert; Sinha, Sumit; Hardy, Richard; Best, James; Sambrook Smith, Gregory; Christensen, Kenneth

    2017-11-01

    Biofilms constitute an important form of bacterial life in aquatic environments and are present at the fluid-solid interfaces in natural and industrial settings, such as water distribution systems and riverbeds among others. The permeable, heterogeneous, and deformable structure of biofilms can influence mass and momentum transport between the subsurface and freestream. However, this interaction is not fully understood, in part due to technical obstacles impeding quantitative experimental investigations. In this work, the effect of biofilm on flow structure over a permeable bed is studied. Experiments are conducted in a closed water channel equipped with an idealized two-dimensional permeable bed. Prior to conducting flow experiments, the models are placed within an independent recirculating reactor for biofilm growth. Once a targeted biofilm growth stage is achieved, the models are transferred to the water channel and subjected to transitional and turbulent flows. Long-distance microscopic particle image velocimetry measurements are performed to quantify the effect of biofilm on the turbulence structure of the free flow as well as the freestream-subsurface flow interaction. Funded by UK Natural Environment Research Council.

  5. Exchange between the stagnant and flowing zone in gas-flowing solids-fixed bed contactors

    Directory of Open Access Journals (Sweden)

    ALEKSANDAR P. DUDUKOVIC

    2005-02-01

    Full Text Available In countercurrent gas – flowing solids – fixed bed contactors, a fraction of the flowing solids is in motion (dynamic holdup, while the other fraction is resting on the fixed bed elements. In this study it was experimentally proved that the stagnant zone should not be considered as a dead part of the column, but that there is a dynamic exchange between these two portions of flowing solids particles. Combining a mathematical model with tracer experiments, the rate of exchange was determined and it was shown that only a small part (ca. 20 % of the stagnant region should be considered as a dead one.

  6. Cross-flow heat transfer in fixed bed

    Science.gov (United States)

    Ma, Hongfang; Zhang, Haitao; Ying, Weiyong; Fang, Dingye

    2013-06-01

    Radial flow reactor operated at cross-flow heat transfer is focused for large scale methanol synthesis. The effects of operating conditions including the reactor inlet air temperature, the heating pipe temperature and the air flow rate on the cross-flow heat transfer were investigated and results show that the temperature profile of the area in front of the heating pipe is slightly affected by all the operating conditions. The main area whose temperature profile is influenced is located behind the heating pipe. The heat transfer direction is related to the direction of the flow. In order to obtain the basic parameters for radial flow reactor designing calculation, the dimensionless number group method was used for data fitting of the bed effective thermal conductivity and the wall heat transfer coefficient which were calculated by the mathematical model with the product of Reynolds number and Prandtl number. The comparison of experimental data and calculated values shows that the calculated values fit the experimental data satisfactorily and the formulas can be used for reactor designing calculation.

  7. Solute dispersion in open channel flow with bed absorption

    Science.gov (United States)

    Wang, Ping; Chen, G. Q.

    2016-12-01

    Reactive solute dispersion is of essential significance in various ecological and environmental applications. It is only qualitatively known that boundary absorption depletes pollutant around the boundary and reduces the concentration nearby. All the existing studies on this topic have been focused on the longitudinally distributed mean concentration, far from enough to fully characterize the transport process with tremendous cross-sectional concentration nonuniformity. This work presents an analytical study of the evolution of two-dimensional concentration distribution for solute dispersion in a laminar open channel flow with bed absorption. The fourth order Aris-Gill expansion proposed in our previous study (Wang and Chen, 2016b) is further extended for the case with bed absorption to cover the transitional effects of skewness and kurtosis. Results reveal the extremely nonuniform cross-sectional concentration distribution, and demonstrate that concentration at the bed instead of the mean should be used for reliable quantification of the absorption flux. The accurate two-dimensional concentration distribution presented in this study brings important environmental implications such as risk assessment associated with peak concentration position and duration of toxic pollutant cloud in open channel waters.

  8. Sediment Resuspension and Bed Morphology in Highly Turbulent Flows

    Science.gov (United States)

    Johnson, B. A.; Cowen, E. A.

    2010-12-01

    Motivated by environmental flows where turbulence levels are set by processes other than mean shear (e.g., breaking surface and internal waves and bores) we choose to study turbulent boundary layers and sediment resuspension in the absence of mean shear using a recently-developed facility designed to generate homogeneous isotropic turbulence with low mean flows. Similar investigations have been performed with grid-stirred tanks (GSTs), though significant mean flows were found to exist in these tanks, altering the balance of fluid forces present. Significantly, we find that the interaction of turbulence with a permeable sediment boundary results in the formation of ripple patterns. Our facility uses a Randomly Actuated Synthetic Jet Array (RASJA) and allows us to control the turbulent forcing while ensuring significantly less mean flow relative to prior facilities. We performed measurements using Particle Image Velocimetry (PIV), first with a solid bottom boundary, to examine the turbulent structures and nature of the flow at the bed. We measured vertical profiles of statistical metrics such as turbulence intensity, turbulent kinetic energy, spectra, and Reynolds stresses. We then replaced the solid boundary with a layer of narrowly graded sand that has a median grain size (D50) of about 250 μm and made direct comparisons to the solid boundary measurements. Finally, in an effort to verify the ability to measure such flows in the field, we used a Nortek Aquadopp HR Profiler to measure vertical profiles over the depth of the tank and examine the Profiler’s ability to record accurate measurements at the fluid-sediment interface. Our analysis includes the determination of critical turbulent stresses responsible for sediment resuspension from the sand bed from which we develop a non-dimensional Shields-like parameter that captures incipient particle motion. We also make comparisons between simultaneous PIV and HR Profiler measurements to improve our understanding of

  9. The impact of structural development on near bed flow dynamics in gravel bed rivers: coupling flume experiments with numerical modelling

    Science.gov (United States)

    Ockelford, A.; Hardy, R. J.; Rice, S. P.; Powell, M.

    2017-12-01

    It is increasingly being recognised that gravel bed rivers develop a surface `texture' in response to changes in the flow and sediment regime. This textural response often takes the form of a bed structure which develops to ultimately stabilise the surface across a range of spatio-temporal scales and it is these topographical structures which determine the flow structures that develop over the river bed. However, our ability to measure and parameterise that structure in ways that are useful and meaningful for the prediction of flow dynamics, still remains inadequate; this paper uses a three dimensional numerical model to assess how the temporal development of structure influences the near bed flow dynamics. Using a suite of flume based experiments a unimodal grain size distribution (σg = 1.30, D50 = 8.8mm) was exposed to three different levels of constant bed shear that produced sediment transport conditions ranging from marginal transport to conditions approaching full mobility of all size fractions. Surface structuring characteristics were measured at a high spatio-temporal resolution such that the time evolution of the beds could be fully described. In total 54 surfaces were generated and run through a Reynolds averaged three dimensional numerical model with an Rng turbulence closure. The topography input included using an immersed boundary technique within a Cartesian framework. Discussion concentrates on the how the trajectory of structural evolution under the different treatments affects the near bed flow dynamics. Specifically links are made between how the scales of boundary topography influence the flow and discusses how the measured flow variability at any one point will contain both locally derived and upstream-inherited flow structures, according to the range of scales of bed topography present. Keywords: Graded, Sediment, Structure, Turbulence, Modelling

  10. Effects of Bed Forms and Large Protruding Grains on Near-Bed Flow Hydraulics in Low Relative Submergence Conditions

    Science.gov (United States)

    Monsalve, Angel; Yager, Elowyn M.; Schmeeckle, Mark W.

    2017-10-01

    In mountain rivers, bed forms, large relatively immobile grains, and bed texture and topographic variability can significantly alter local and reach-averaged flow characteristics. The low relative submergence of large immobile grains causes highly three-dimensional flow fields that may not be represented by traditional shear stress, flow velocity, and turbulence intensity equations. To explore the influence of large protruding grains and bed forms on flow properties, we conducted a set of experiments in which we varied the relative submergence while holding the sediment transport capacity and upstream sediment supply constant. Flow and bed measurements were conducted at the beginning and end of each experiment to account for the absence or presence of bed forms, respectively. Detailed information on the flow was obtained by combining our measurements with a 3-D numerical model. Commonly used velocity profile equations only performed well at the reach scale when shallow flow effects and the roughness length of the relatively mobile sediment were considered. However, at the local scale large deviations from these profiles were observed and simple methods to estimate the spatial distribution of near-bed shear stresses are likely to be inaccurate. Zones of high turbulent kinetic energy occurred near the water surface and were largely controlled by the immobile grains and plunging flow. The reach-averaged shear stress did not correlate to depth or slope, as commonly assumed, but instead was controlled by the relative boulder submergence and degree of plunging flow. For accurate flow predictions in mountain rivers, the effects of bed forms and large boulders must be considered.

  11. Flow resistance in open channels with fixed movable bed

    Science.gov (United States)

    Simoes, Francisco J.

    2010-01-01

    In spite of an increasingly large body of research by many investigators, accurate quantitative prediction of open channel flow resistance remains a challenge. In general, the relations between the elements influencing resistance (turbulence, boundary roughness, and channel shape features, such as discrete obstacles, bars, channel curvature, recirculation areas, secondary circulation, etc.) and mean flow variables are complex and poorly understood. This has resulted in numerous approaches to compute friction using many and diverse variables and equally diverse prescriptions for their use. In this paper, a new resistance law for surface (grain) resistance, the resistance due to the flow viscous effects on the channel boundary roughness elements, is presented for the cases of flow in the transition (5 friction losses in channels and natural rivers with plane beds, regardless of sediment transport conditions. This work is useful to hydraulic engineers involved with the derivation of depth-discharge relations in open channel flow and with the estimation of sediment transport rates for the case of bedload transport.

  12. Three dimensional flow field at confluent fixed-bed open channels

    OpenAIRE

    Schleiss, Anton; De Cesare, Giovanni; Franca, Mário J.; Pfister, Michael; Birjukova, Olga; Guillén Ludeña, Sebastián; Alegria, Francisco; Cardoso, Antonio H.

    2014-01-01

    River confluences are known for their marked 3D patterns and, due to the complexity of local flow features and bed morphology, they require particular consideration. Although there are studies on the flow structure in junctions of two streams, amore detailed description of the flow patterns is still required. The objective of this work is to contribute to such description at river confluence for concordant bed, where both main and tributary channel beds have the same elevation. For that purpo...

  13. Down-flow moving-bed gasifier with catalyst recycle

    Science.gov (United States)

    Halow, John S.

    1999-01-01

    The gasification of coal and other carbonaceous materials by an endothermic gasification reaction is achieved in the presence of a catalyst in a down-flow, moving-bed gasifier. Catalyst is removed along with ash from the gasifier and is then sufficiently heated in a riser/burner by the combustion of residual carbon in the ash to volatilize the catalyst. This volatilized catalyst is returned to the gasifier where it uniformly contacts and condenses on the carbonaceous material. Also, the hot gaseous combustion products resulting from the combustion of the carbon in the ash along with excess air are introduced into the gasifier for providing heat energy used in the endothermic reaction.

  14. Flow velocities and bed shear stresses in a stone cover under an oscillatory flow

    DEFF Research Database (Denmark)

    Stenanato, F.; Nielsen, Anders Wedel; Sumer, B. Mutlu

    2010-01-01

    layers of stones. The flow velocities in the pores of the stones were measured using LDA (Laser Doppler Anemometer). In addition to the velocity measurements, the bed shear stresses were also measured using a hotfilm (Constant Temperature Anemometry). It is found that the boundary layer of the outer flow...... current boundary layer without any externally generated turbulence. The bd shear stress is found to be very low, more than ten times smaller than in the case of a smooth base bottom without stone cover....

  15. 2D numerical model of particle-bed collision in fluid-particle flows over bed

    Czech Academy of Sciences Publication Activity Database

    Lukerchenko, Nikolay; Chára, Zdeněk; Vlasák, Pavel

    2006-01-01

    Roč. 44, č. 1 (2006), s. 70-78 ISSN 0022-1686 R&D Projects: GA AV ČR IAA2060201 Institutional research plan: CEZ:AV0Z20600510 Keywords : saltation * particle-bed collision * collision angle * bed roughness Subject RIV: BK - Fluid Dynamics Impact factor: 0.527, year: 2006

  16. Assessment of a Danish sludge treatment reed bed system and a stockpile area, using substance flow analysis

    DEFF Research Database (Denmark)

    Larsen, Julie Dam; Nielsen, Steen M; Scheutz, Charlotte

    2017-01-01

    of substances in an STRB system over a 12-year treatment period, followed by three months' post-treatment in a stockpile area (SPA). Samples of sludge, reject water and sludge residue of different ages were collected at two Danish STRB system facilities and analysed for content of relevant substances....... Concentrations of carbon and nitrogen in the sludge residue residing in an STRB system changed as a function of treatment time, mainly due to mineralisation; only a negligible part was lost to reject water. Considering metals and phosphorus, the main share was accumulated in the sludge residue; only minor...... fractions were lost to mineralisation or reject water. Post-treatment in an SPA resulted in an increase in dry matter content from 24% to 32%. After treatment, the concentrations of heavy metals (lead, cadmium, nickel, zinc, copper and chromium) in the sludge residue met the threshold values stated...

  17. Model investigations 3D of gas-powder two phase flow in descending bed with consideration radial distribution of flow

    Directory of Open Access Journals (Sweden)

    B. Panic

    2013-04-01

    Full Text Available The results of experimental investigations concerning radial distribution of powder accumulation in bed and static pressure were presented in this paper. To realize this research physical model of gas-powder two phase flow with descending bed was projected and constructed. Amounts of “dynamic” and “static” powder accumulated in bed, in dependence on gas velocity and of bed particles were investigated. In 3D model “static” powder (with its radial distribution at the tuyere level and in the higher part of bed was measured. The influence of bed particles, powder and gas radial distribution on values of interaction forces between flow phases in investigated system was defined.

  18. Positive feedback and momentum growth during debris-flow entrainment of wet bed sediment

    Science.gov (United States)

    Iverson, R.M.; Reid, M.E.; Logan, M.; LaHusen, R.G.; Godt, J.W.; Griswold, J.P.

    2011-01-01

    Debris flows typically occur when intense rainfall or snowmelt triggers landslides or extensive erosion on steep, debris-mantled slopes. The flows can then grow dramatically in size and speed as they entrain material from their beds and banks, but the mechanism of this growth is unclear. Indeed, momentum conservation implies that entrainment of static material should retard the motion of the flows if friction remains unchanged. Here we use data from large-scale experiments to assess the entrainment of bed material by debris flows. We find that entrainment is accompanied by increased flow momentum and speed only if large positive pore pressures develop in wet bed sediments as the sediments are overridden by debris flows. The increased pore pressure facilitates progressive scour of the bed, reduces basal friction and instigates positive feedback that causes flow speed, mass and momentum to increase. If dryer bed sediment is entrained, however, the feedback becomes negative and flow momentum declines. We infer that analogous feedbacks could operate in other types of gravity-driven mass flow that interact with erodible beds. ?? 2011 Macmillan Publishers Limited. All rights reserved.

  19. Particle flow of ceramic breeder pebble beds in bi-axial compression experiments

    International Nuclear Information System (INIS)

    Hermsmeyer, S.; Reimann, J.

    2002-01-01

    Pebble beds of Tritium breeding ceramic material are investigated within the framework of developing solid breeder blankets for future nuclear fusion power plants. For the thermo-mechanical characterisation of such pebble beds, bed compression experiments are the standard tools. New bi-axial compression experiments on 20 and 30 mm high pebble beds show pebble flow effects much more pronounced than in previous 10 mm beds. Owing to the greater bed height, conditions are reached where the bed fails in cross direction and unhindered flow of the pebbles occurs. The paper presents measurements for the orthosilicate and metatitanate breeder materials that are envisaged to be used in a solid breeder blanket. The data are compared with calculations made with a Drucker-Prager soil model within the finite-element code ABAQUS, calibrated with data from other experiments. It is investigated empirically whether internal bed friction angles can be determined from pebble beds of the considered heights, which would simplify, and broaden the data base for, the calibration of the Drucker-Prager pebble bed models

  20. Enhanced Forced Convection Heat Transfer using Small Scale Vorticity Concentrations Effected by Flow Driven, Aeroelastically Vibrating Reeds

    Science.gov (United States)

    2016-08-03

    channel was increased gradually (at a rate of about 16 cm/sec/sec) using a flow controller that is built into the air supply (cf., §III.3.1) while...integrated film heaters (operating in constant heat flux, cf, §III.3.1). The heat flux to the heaters was varied over a range of flow rates (2,000...AFRL-AFOSR-VA-TR-2016-0339 Enhanced convection heat transfer using small-scale vorticity concentrations effected by flow -driven, aeroelastically

  1. Acceleration of coupled granular flow and fluid flow simulations in pebble bed energy systems

    Energy Technology Data Exchange (ETDEWEB)

    Li, Yanheng, E-mail: liy19@rpi.edu [Department of Mechanical, Aerospace, and Nuclear Engineering, Rensselaer Polytechnic Institute, 110 8th Street, Troy, NY (United States); Ji, Wei, E-mail: jiw2@rpi.edu [Department of Mechanical, Aerospace, and Nuclear Engineering, Rensselaer Polytechnic Institute, 110 8th Street, Troy, NY (United States)

    2013-05-15

    Highlights: ► Fast simulation of coupled pebble flow and coolant flow in PBR systems is studied. ► Dimension reduction based on axisymmetric geometry shows significant speedup. ► Relaxation of coupling frequency is investigated and an optimal range is determined. ► A total of 80% efficiency increase is achieved by the two fast strategies. ► Fast strategies can be applied to simulating other general fluidized bed systems. -- Abstract: Fast and accurate approaches to simulating the coupled particle flow and fluid flow are of importance to the analysis of large particle-fluid systems. This is especially needed when one tries to simulate pebble flow and coolant flow in Pebble Bed Reactor (PBR) energy systems on a routine basis. As one of the Generation IV designs, the PBR design is a promising nuclear energy system with high fuel performance and inherent safety. A typical PBR core can be modeled as a particle-fluid system with strong interactions among pebbles, coolants and reactor walls. In previous works, the coupled Discrete Element Method (DEM)-Computational Fluid Dynamics (CFD) approach has been investigated and applied to modeling PBR systems. However, the DEM-CFD approach is computationally expensive due to large amounts of pebbles in PBR systems. This greatly restricts the PBR analysis for the real time prediction and inclusion of more physics. In this work, based on the symmetry of the PBR geometry and the slow motion characteristics of the pebble flow, two acceleration strategies are proposed. First, a simplified 3D-DEM/2D-CFD approach is proposed to speed up the DEM-CFD simulation without loss of accuracy. Pebble flow is simulated by a full 3D DEM, while the coolant flow field is calculated with a 2D CFD simulation by averaging variables along the annular direction in the cylindrical and annular geometries. Second, based on the slow motion of pebble flow, the impact of the coupling frequency on the computation accuracy and efficiency is

  2. Acceleration of coupled granular flow and fluid flow simulations in pebble bed energy systems

    International Nuclear Information System (INIS)

    Li, Yanheng; Ji, Wei

    2013-01-01

    Highlights: ► Fast simulation of coupled pebble flow and coolant flow in PBR systems is studied. ► Dimension reduction based on axisymmetric geometry shows significant speedup. ► Relaxation of coupling frequency is investigated and an optimal range is determined. ► A total of 80% efficiency increase is achieved by the two fast strategies. ► Fast strategies can be applied to simulating other general fluidized bed systems. -- Abstract: Fast and accurate approaches to simulating the coupled particle flow and fluid flow are of importance to the analysis of large particle-fluid systems. This is especially needed when one tries to simulate pebble flow and coolant flow in Pebble Bed Reactor (PBR) energy systems on a routine basis. As one of the Generation IV designs, the PBR design is a promising nuclear energy system with high fuel performance and inherent safety. A typical PBR core can be modeled as a particle-fluid system with strong interactions among pebbles, coolants and reactor walls. In previous works, the coupled Discrete Element Method (DEM)-Computational Fluid Dynamics (CFD) approach has been investigated and applied to modeling PBR systems. However, the DEM-CFD approach is computationally expensive due to large amounts of pebbles in PBR systems. This greatly restricts the PBR analysis for the real time prediction and inclusion of more physics. In this work, based on the symmetry of the PBR geometry and the slow motion characteristics of the pebble flow, two acceleration strategies are proposed. First, a simplified 3D-DEM/2D-CFD approach is proposed to speed up the DEM-CFD simulation without loss of accuracy. Pebble flow is simulated by a full 3D DEM, while the coolant flow field is calculated with a 2D CFD simulation by averaging variables along the annular direction in the cylindrical and annular geometries. Second, based on the slow motion of pebble flow, the impact of the coupling frequency on the computation accuracy and efficiency is

  3. Influence of decelerating flow on incipient motion of a gravel-bed ...

    Indian Academy of Sciences (India)

    2Department of Civil Engineering, Indian Institute of Technology,. Kharagpur 721 302. ∗ ... has applications to a wide variety of research problems, such as stable channel design, scouring of river-beds, etc. ... Song & Graf (1994) carried out research on the effect of uniform flow in open channels with movable gravel-bed.

  4. Turbulent flow and sand transport over a cobble bed in a laboratory flume

    Science.gov (United States)

    The turbulence structure of flow over rough beds and its interaction with fine sediments in the bed are important for efforts to predict sediment transport downstream of dams. The advanced age and impending decommissioning of many dams have brought increased attention to the fate of sediments stored...

  5. Water flow across and sediment trapping in submerged macrophyte beds of contrasting growth form

    NARCIS (Netherlands)

    Vermaat, J.E.; Santamaria, L.; Roos, P.J.

    2000-01-01

    Patterns of wave amplitudes, linear flow velocity, turbidity, sedimentation and periphyton accumulation were quantified across two macrophyte beds of contrasting architecture and adjacent unvegetated sediments, in Lake Veluwe, The Netherlands. Within both a Chara aspera- and an Alisma

  6. Chemical-looping combustion in a reverse-flow fixed bed reactor

    International Nuclear Information System (INIS)

    Han, Lu; Bollas, George M.

    2016-01-01

    A reverse-flow fixed bed reactor concept for CLC (chemical-looping combustion) is explored. The limitations of conventional fixed bed reactors, as applied to CLC, are overcome by reversing the gas flow direction periodically to enhance the mixing characteristics of the bed, thus improving oxygen carrier utilization and energy efficiency with respect to power generation. The reverse-flow reactor is simulated by a dusty-gas model and compared with an equivalent fixed bed reactor without flow reversal. Dynamic optimization is used to calculate conditions at which each reactor operates at maximum energy efficiency. Several cases studies illustrate the benefits of reverse-flow operation for the CLC with CuO and NiO oxygen carriers and methane and syngas fuels. The results show that periodic reversal of the flow during reduction improves the contact between the fuel and unconverted oxygen carrier, enabling the system to suppress unwanted catalytic reactions and axial temperature and conversion gradients. The operational scheme presented reduces the fluctuations of temperature during oxidation and increases the high-temperature heat produced by the process. CLC in a reverse-flow reactor has the potential to achieve higher energy efficiency than conventional fixed bed CLC reactors, when integrated with a downstream gas turbine of a combined cycle power plant. - Highlights: • Reverse-flow fixed bed CLC reactors for combined cycle power systems. • Dynamic optimization tunes operation of batch and transient CLC systems. • The reverse-flow CLC system provides stable turbine-ready gas stream. • Reverse-flow CLC fixed bed reactor has superior CO 2 capture and thermal efficiency.

  7. The Dynamic Behavior of Water Flowing Through Packed Bed of Different Particle Shapes and Sizes

    Directory of Open Access Journals (Sweden)

    Haneen Ahmed Jasim

    2017-12-01

    Full Text Available An experimental study was conducted on pressure drop of water flow through vertical cylindrical packed beds in turbulent region and the influence of the operating parameters on its behavior. The bed packing was made of spherical and non-spherical particles (spheres, Rasching rings and intalox saddle with aspect ratio range 3.46 D/dp 8.486 obtaining bed porosities 0.396 0.84 and Reynolds number 1217 21758. The system is consisted of 5 cm inside diameter Perspex column, 50 cm long; distilled water was pumped through the bed with flow rate 875, 1000, 1125, 1250,1375 and 1500 l/h and inlet water temperature 20, 30, 40 and 50 ˚C. The packed bed system was monitored by using LabVIEW program, were the results have been obtained from Data Acquisition Adaptor (DAQ.

  8. Particle motions in oscillatory flow over a smooth bed

    DEFF Research Database (Denmark)

    Jensen, Karsten Lindegård; Sumer, B. Mutlu; Fredsøe, Jørgen

    2014-01-01

    This study investigates particle motions near the bed in an oscillating tunnel with a smooth bed. Trajectories of a heavy particle were recorded in two dimensions (horizontal and vertical) and in time. The wave boundary layer Reynolds number is Re = 520000. Kinematical quantities...... such as the probability distribution of particle position in the vertical, and the horizontal and vertical particle velocities, among others, are determined. The particle is observed to reach heights of 2.5-3d, similar to that characterizing a typical bedload particle in sediment transport....

  9. Flow resistance in a compound gravel-bed bend

    Indian Academy of Sciences (India)

    centrifugal force having a lateral momentum transfer. This force disappears after leaving a bend exit. Thus, the turbulent shear stress is the resistance that the flow has to overcome in transforming from a primary flow into a secondary flow pattern and vice versa. The increase in flow resistance in a meandering path can be ...

  10. Slow sedimentary processes on-a-chip: experiments on porous flow effects on granular bed creep

    Science.gov (United States)

    Houssais, M.; Maldarelli, C.; Shattuck, M.; Morris, J. F.

    2017-12-01

    Steep soils dynamics is hard to catch. they exhibit very slow granular creep most of the time, and sometimes, mostly under or after rain, turn into a landslide, a very fast avalanche flow.The conditions of transition from soil creep to avalanching remains a lot non-understood, and Safe Factor law (empirical criteria, function of rain intensity and duration). On another side, in marine fast deposition environments, compaction drives vertical porous flow, which makes bed shear resistance change, and form over time bed size patterns (pipes, dishes) or mechanical heterogeneities.Capturing how the slow creep dynamics depends on the porous flow would allow for much more accurate landscape evolution modeling.We present here preliminary results of an experimental investigation of one the major triggering condition for soils destabilization: rain infiltration, and more generally porous flow through a tilted granular bed. In a quasi-2D microfluidics channel, a flat sediment bed made of spherical particles is prepared, in fully submerged condition. It is thereafter tilted (at slope under critical slope of avalanching) and simultaneously put under vertical weak porous flow (well under the critical flow of liquefaction regarding positive pressure gradients). The two control parameters are varied, and local particles concentration and motion are measured. Interestingly, although staying in the sub-critical creeping regime, we observe an acceleration of the bed deformation downward, as the porous flow and the bed slope are increased, until the criteria for avalanching is reached. Those results appear to present similitudes with the case of tilted dry sediment bed under controlled vibrations. Consequently it opens the discussion about a potential universal model of landslides triggering due to frequent seismological and rainstorm events.

  11. Elementary theory of bed-sediment entrainment by debris flows and avalanches

    Science.gov (United States)

    Iverson, Richard M.

    2012-01-01

    Analyses of mass and momentum exchange between a debris flow or avalanche and an underlying sediment layer aid interpretations and predictions of bed-sediment entrainment rates. A preliminary analysis assesses the behavior of a Coulomb slide block that entrains bed material as it descends a uniform slope. The analysis demonstrates that the block's momentum can grow unstably, even in the presence of limited entrainment efficiency. A more-detailed, depth-integrated continuum analysis of interacting, deformable bodies identifies mechanical controls on entrainment efficiency, and shows that entrainment rates satisfy a jump condition that involves shear-traction and velocity discontinuities at the flow-bed boundary. Explicit predictions of the entrainment rateEresult from making reasonable assumptions about flow velocity profiles and boundary shear tractions. For Coulomb-friction tractions, predicted entrainment rates are sensitive to pore fluid pressures that develop in bed sediment as it is overridden. In the simplest scenario the bed sediment liquefies completely, and the entrainment-rate equation reduces toE = 2μ1gh1 cos θ(1 − λ1)/ , where θ is the slope angle, μ1 is the flow's Coulomb friction coefficient, h1 is its thickness, λ1 is its degree of liquefaction, and is its depth-averaged velocity. For values ofλ1ranging from 0.5 to 0.8, this equation predicts entrainment rates consistent with rates of 0.05 to 0.1 m/s measured in large-scale debris-flow experiments in which wet sediment beds liquefied almost completely. The propensity for bed liquefaction depends on several factors, including sediment porosity, permeability, and thickness, and rates of compression and shear deformation that occur when beds are overridden.

  12. Heat-transfer characteristics of flowing and stationary particle-bed-type fusion-reactor blankets

    Energy Technology Data Exchange (ETDEWEB)

    Nietert, R.E.

    1983-02-01

    The heat-transfer characteristics of flowing and stationary packed-particle beds have recently become of interest in connection with conceptual designs of fusion reactor blankets. A detailed literature survey has shown that the processes taking place in such beds are not fully understood despite their widespread use in the chemical industry and other engineering disciplines for more than five decades. In this study, two experimental investigations were pursued. In the first, a heat-transfer loop was constructed through which glass microspheres were allowed to flow by rgravity at controlled rates through an electrically heated stainless steel tubular test section. In the second, an annular packed bed was constructed in which heat was applied through the outer wall by electric heating of a stainless steel tube. Cooling occurred at the inner wall of the annular bed by flowing air through the central tube. A second air stream was allowed to flow through the voids of the packed bed. An error-minimization technique was utilized in order to obtain the two-dimensional one-parameter effective conductivity for the bed by comparing the experimental and theoretically predicted temperature profiles. Experiments were conducted for various modified Reynolds numbers less than ten.

  13. Effects of bed-load movement on flow resistance over bed forms

    Indian Academy of Sciences (India)

    Tehran, Iran. 2Department of Irrigation and Reclamation Engineering, Soil and Water Faculty,. University of Tehran, Tehran, Iran ... Steady flow of clear as against sediment-laden water with different flow depths and velocities were studied in the ..... McGraw-Hill Series In: Water Resource and Envi- ronmental Engineering.

  14. Flow Pattern in a Fluidized Bed with a Non-fluidized Zone

    DEFF Research Database (Denmark)

    Lin, Weigang; Dam-Johansen, Kim; Van den Bleek, Cor. M.

    1997-01-01

    The flow pattern of a fluidized bed with non-fluidized zones is investigated both experimentally and theoretically. Experiments were carried out in such a way that air was introduced only through part of the distributor. The results show a significant amount of air flowing to the zone where no ai...

  15. Studies for determining drain solid flow in bed silt, using radioisotope techniques

    International Nuclear Information System (INIS)

    Sanchez, W.

    1976-01-01

    A process for measuring solid flow in silt bed using isotopic technique is studied. Comparative studies for initial movement of grinded glass grains and sand grains is done. The development for determining the minimum mass of radioative grains of sand, used for flow evaluation is also studied. Further experiments in the field of reference confirm technological conditions for the method [pt

  16. Bed load size distribution and flow conditions in a high mountain catchment of Central Pyrenees

    OpenAIRE

    Martínez Castroviejo, Ricardo

    1990-01-01

    The bed load size distribution caused by different types of flow are compared in a high mountain catchment located in the upper Gallego river basin (Central Spanish’ Pyrenees). Three kinds of hydrologic events could be defined: those triggered by heavy autumn rainfalls, those originated by isolated summer rainstorms and those promoted by snowmelting. Each one is characterized by a peculiar bed load size distribution. Thus, it could be demonstrated that the coarser fractions, above 30 mm in di...

  17. Contraction rate, flow modification and bed layering impact on scour at the elliptical guide banks

    Science.gov (United States)

    Gjunsburgs, B.; Jaudzems, G.; Bizane, M.; Bulankina, V.

    2017-10-01

    Flow contraction by the bridge crossing structures, intakes, embankments, piers, abutments and guide banks leads to general scour and the local scour in the vicinity of the structures. Local scour is depending on flow, river bed and structures parameters and correct understanding of the impact of each parameter can reduce failure possibility of the structures. The paper explores hydraulic contraction, the discharge redistribution between channel and floodplain during the flood, local flow modification and river bed layering on depth, width and volume of scour hole near the elliptical guide banks on low-land rivers. Experiments in a flume, our method for scour calculation and computer modelling results confirm a considerable impact of the contraction rate of the flow, the discharge redistribution between channel and floodplain, the local velocity, backwater and river bed layering on the depth, width, and volume of scour hole in steady and unsteady flow, under clear water condition. With increase of the contraction rate of the flow, the discharge redistribution between channel and floodplain, the local velocity, backwater values, the scour depth increases. At the same contraction rate, but at a different Fr number, the scour depth is different: with increase in the Fr number, the local velocity, backwater, scour depth, width, and volume is increasing. Acceptance of the geometrical contraction of the flow, approach velocity and top sand layer of the river bed for scour depth calculation as accepted now, may be the reason of the structures failure and human life losses.

  18. Cold-Flow Circulating Fluidized-Bed Identification

    Energy Technology Data Exchange (ETDEWEB)

    Parviz Famouri

    2005-07-01

    In a variety of industrial applications, the use of a circulating fluidized bed (CFB) provides various advantages, such as reducing environmental pollution and increasing process efficiency. The application of circulating fluidized bed technology contributes to the improvement of gas-solid contact, reduction of the cross-sectional area with the use of higher superficial velocities, the use of the solids circulation rate as an additional control variable, and superior radial mixing, Grace et al. [1]. In order to improve raw material usage and utility consumption, optimization and control of CFB is very important, and an accurate, real time model is required to describe and quantify the process. Currently there is no accepted way to construct a reliable model for such a complex CFB system using traditional methods, especially at the pilot or industrial scale. Three major obstacles in characterizing the system are: 1) chaotic nature of the system; 2) non-linearity of the system, and 3) number of immeasurable unknowns internal to the system,[2]. Advanced control theories and methods have the ability to characterize the system, and can overcome all three of these obstacles. These methods will be discussed in this report.

  19. COOLOCE debris bed experiments and simulations investigating the coolability of cylindrical beds with different materials and flow modes

    Energy Technology Data Exchange (ETDEWEB)

    Takasuo, E.; Kinnunen, T.; Holmstroem, S.; Lehtikuusi, T. [VTT Technical Research Centre of Finland (Finland)

    2013-07-15

    The COOLOCE experiments aim at investigating the coolability of debris beds of different geometries, flow modes and materials. A debris bed may be formed of solidified corium as a result of a severe accident in a nuclear power reactor. The COOLOCE-8 test series consisted of experiments with a top-flooded test bed with irregular gravel as the simulant material. The objective was to produce comparison data useful in estimating the effects of different particle materials and the possible effect of the test arrangement on the results. It was found that the dryout heat flux (DHF) measured for the gravel was lower compared to previous experiments with spherical beads, and somewhat lower compared to the early STYX experiments. The difference between the beads and gravel is at least partially explained by the smaller average size of the gravel particles. The COOLOCE-9 test series included scoping experiments examining the effect of subcooling of the water pool in which the debris bed is immersed. The experiments with initially subcooled pool suggest that the subcooling may increase DHF and increase coolability. The aim of the COOLOCE-10 experiments was to investigate the effect of lateral flooding on the DHF a cylindrical test bed. The top of the test cylinder and its sidewall were open to water infiltration. It was found that the DHF is increased compared to a top-flooded cylinder by more than 50%. This suggests that coolability is notably improved. 2D simulations of the top-flooded test beds have been run with the MEWA code. Prior to the simulations, the effective particle diameter for the spherical beads and the irregular gravel was estimated by single-phase pressure loss measurements performed at KTH in Sweden. Parameter variations were done for particle size and porosity used as input in the models. It was found that with the measured effective particle diameter and porosity, the simulation models predict DHF with a relatively good accuracy in the case of spherical

  20. DEM-CFD simulation of purge gas flow in a solid breeder pebble bed

    Energy Technology Data Exchange (ETDEWEB)

    Zhang, Hao [School of Nuclear Science and Technology, University of Science and Technology of China, Hefei 230027 (China); Institute of Nuclear Physics and Chemistry, China Academy of Engineering Physics, Mianyang 621900 (China); Li, Zhenghong [Institute of Nuclear Physics and Chemistry, China Academy of Engineering Physics, Mianyang 621900 (China); University of Science and Technology of China, Hefei 230027 (China); Guo, Haibing [Institute of Nuclear Physics and Chemistry, China Academy of Engineering Physics, Mianyang 621900 (China); Ye, Minyou [School of Nuclear Science and Technology, University of Science and Technology of China, Hefei 230027 (China); Huang, Hongwen, E-mail: inpclane@sina.com [Institute of Nuclear Physics and Chemistry, China Academy of Engineering Physics, Mianyang 621900 (China)

    2016-12-15

    Solid tritium breeding blanket applying pebble bed concept is promising for fusion reactors. Tritium bred in the pebble bed is purged out by inert gas. The flow characteristics of the purge gas are important for the tritium transport from the solid breeder materials. In this study, a randomly packed pebble bed was generated by Discrete Element Method (DEM) and verified by radial porosity distribution. The flow parameters of the purge gas in channels were solved by Computational Fluid Dynamics (CFD) method. The results show that the normalized velocity magnitudes have the same damped oscillating patterns with radial porosity distribution. Besides, the bypass flow near the wall cannot be ignored in this model, and it has a slight increase with inlet velocity. Furthermore, higher purging efficiency becomes with higher inlet velocity and especially higher in near wall region.

  1. Flow visualizing study of fluidized bed for incineration and/or coal combustion technology

    Energy Technology Data Exchange (ETDEWEB)

    Ozawa, Mamoru [Kansai Univ., Suita, Osaka (Japan). Faculty of Engineering

    1997-02-01

    A simulated fluidized-bed heat exchanger was visualized using a neutron radiography system. The void fraction distribution and its fluctuation were obtained by means of an image processing technique. On the basis of the processed image, the mechanism of a large particle movement and the flow pattern in the tube bank immersed in the bed were investigated. Observed flow pattern in the tube bank indicated an importance of the tube arrangement on the void fraction fluctuation and thus the heat transfer around tubes. (author)

  2. Sediment transport capacity of concentrated flows on steep loessial slope with erodible beds.

    Science.gov (United States)

    Xiao, Hai; Liu, Gang; Liu, Puling; Zheng, Fenli; Zhang, Jiaqiong; Hu, Feinan

    2017-05-24

    Previous research on sediment transport capacity has been inadequate and incomplete in describing the detachment and transport process of concentrated flows on slope farmlands during rill development. An indoor concentrated flow scouring experiment was carried out on steep loessial soil slope with erodible bed to investigate the sediment transport capacity under different flow rates and slope gradients. The results indicated that the sediment transport capacity increases with increasing flow rate and slope gradient, and these relationships can be described by power functions and exponential functions, respectively. Multivariate, nonlinear regression analysis showed that sediment transport capacity was more sensitive to slope gradient than to flow rate, and it was more sensitive to unit discharge per unit width than to slope gradient for sediment transport capacity in this study. When similar soil was used, the results were similar to those of previous research conducted under both erodible and non-erodible bed conditions. However, the equation derived from previous research under non-erodible bed conditions with for river bed sand tends to overestimate sediment transport capacity in our experiment.

  3. Seasonal Greenland Ice Sheet ice flow variations in regions of differing bed and surface topography

    Science.gov (United States)

    Sole, A. J.; Livingstone, S. J.; Rippin, D. M.; Hill, J.; McMillan, M.; Quincey, D. J.

    2015-12-01

    The contribution of the Greenland Ice Sheet (GrIS) to future sea-level rise is uncertain. Observations reveal the important role of basal water in controlling ice-flow to the ice sheet margin. In Greenland, drainage of large volumes of surface meltwater to the ice sheet bed through moulins and hydrofracture beneath surface lakes dominates the subglacial hydrological system and provides an efficient means of moving mass and heat through the ice sheet. Ice surface and bed topography influence where meltwater can access the bed, and the nature of its subsequent flow beneath the ice. However, no systematic investigation into the influence of topographic variability on Greenland hydrology and dynamics exists. Thus, physical processes controlling storage and drainage of surface and basal meltwater, and the way these affect ice flow are not comprehensively understood. This presents a critical obstacle in efforts to predict the future evolution of the GrIS. Here we present high-resolution satellite mapping of the ice-surface drainage network (e.g. lakes, channels and moulins) and measurements of seasonal variations in ice flow in south west Greenland. The region is comprised of three distinct subglacial terrains which vary in terms of the amplitude and wavelength and thus the degree to which basal topography is reflected in the ice sheet surface. We find that the distribution of surface hydrological features is related to the transfer of bed topography to the ice sheet surface. For example, in areas of thinner ice and high bed relief, moulins occur more frequently and are more uniformly dispersed, indicating a more distributed influx of surface-derived meltwater to the ice sheet bed. We investigate the implications of such spatial variations in surface hydrology on seasonal ice flow rates.

  4. Experimental Study on Pressure Drop and Flow Dispersion in Packed Bed of Natural Zeolite

    Directory of Open Access Journals (Sweden)

    Ruya Petric Marc

    2018-01-01

    Full Text Available The use of conventional correlation for pressure drop and dispersion coefficient calculation may result in inaccurate values for zeolite packed bed as the correlations are generally developed for regularly shaped and uniformly sized particles. To support the research on the application of modified natural zeolite as tar cracking catalyst, the research on the hydrodynamic behaviour of zeolite packed bed has been conducted. Experiments were carried out using a glass column with diameter of 37.8 mm. Natural zeolite with particle size of about 2.91 to 6.4 mm was applied as packing material in the column, and the bed height was varied at 9, 19 and 29 cm. Air was used as the fluid that flows through the bed and nitrogen was used as a tracer for residence time distribution determination. Air flow rates were in the range of 20 to 100 mL/s which correspond to the laminar-transitional flow regime. The pressure drops through the bed were in the range of 1.7 to 95.6 Pa, depending on the air flow rate and bed height. From these values, the parameters in the Ergun equation were estimated, taking into account the contribution by wall effect when the ratio of column to particle diameter is low. The viscous and inertial term constants in the Ergun equation calculated ranges from 179 to 199 and 1.41 to 1.47 respectively while the particle sphericity ranges from 0.56 to 0.59. The reactor Peclet number were determined to range from 5.2 to 5.5, which indicated significant deviation from a plug flow condition.

  5. Quantitative flow visualization of fluidized-bed heat exchanger by neutron radiography

    International Nuclear Information System (INIS)

    Ozawa, M.; Umekawa, H.; Furui, S.; Hayashi, K.; Takenaka, N.

    2004-01-01

    Quantitative flow visualization of a gas-solid fluidized-bed installed vertical tube-bank has been successfully conducted using neutron radiography and image processing technique. The quantitative data of void fraction distribution as well as the fluctuation data are presented. The time-averaged void fraction is well correlated by the drift-flux model. The bubbles formed in the bed, rise along the vertical tubes and the observed bubble size is smaller than that in a free bubbling bed without tube-banks. The bubble diameter is well correlated by the modified Mori and Wen's correlation taking into account the pitch of tube arrangement. The bubble rise velocity is also well correlated by applying the drift-flux model. These results are consistent for both bed materials of Geldart's B- and A-particles, while the bubble size is significantly different between two kinds of particles

  6. Reactive Gas Solids Flow in Circulating Fluidised Beds

    DEFF Research Database (Denmark)

    Hjertager, Bjørn Helge; Solberg, Tron; Hansen, Kim Granly

    2005-01-01

    Progress in modelling and simulation of flow processes in gas/particle systems carried out at the authors? research group are presented. Emphasis is given to computational fluid dynamics (CFD) models that use the multi-dimensional multi fluid techniques. Turbulence modelling strategies for gas/pa...

  7. Hydrodynamic studies of the flow of fine particles through a fluidized dense bed of coarse solids

    Energy Technology Data Exchange (ETDEWEB)

    Talukdar, J.

    1993-12-31

    This study explains the hydrodynamics of a circulating fluidized bed (CFB) system, the Battelle Multi-Solids Fluidized Bed System (MSFB). It consists of a circulating fluidized bed of fine particles superimposed on a bubbling bed of coarse solids. One way to characterize such a system is to describe the mechanism of gas-solid flow through the bed. The gas flow in systems like these is through bubbles or slugs (regions of voids containing little or no solids). Bubbles are typically characterized by their size (length or diameter), their rise velocity, and their frequency. Another task of the initial phase of this study is to characterize an L-valve, a solids-recirculating device commonly used in an MSFB. Next, the mechanism of fine particle movement through a bubbling region of coarse fluidized solids is studied in considerable detail. Bubble characteristics are studied in a variety of systems of coarse particles with fines passing through at high velocity. Amongst numerous optical, electrical and other techniques available for the study of the passage of bubbles, the pressure fluctuation technique is the most robust. In this investigation, pressure probes are connected to pressure transducers which are in turn linked to an on-line data acquisition system supported on a microcomputer. A commercially available software package (Notebook) is used to sample pressure at specified points in the fluidized bed at extremely fast rates, of up to 200 Hz. This resulted in pressure-time traces which are analysed to give bubble length, bubble rise velocity, and bubble frequency. Another important objective of this study is to estimate the fine particle residence time in the dense bed section. A defluidization technique is utilized in experimentally measuring the solids holdup in the dense bed. A mathematical model is developed from first principles, based on a momentum balance on the fine particles.

  8. Preliminary performance analysis of a transverse flow spectrally selective two-slab packed bed volumetric receiver

    CSIR Research Space (South Africa)

    Roos, TH

    2016-05-01

    Full Text Available to the incident radiation (transverse flow). The gap between the window and slab 1 has been removed, so the bed is held in place by the sidewalls, the floor and the window, allowing arbitrary orientation and dispensing with the need for beam-down operation...

  9. Kinetic model for an up-flow anaerobic packed bed bioreactor: Dairy ...

    African Journals Online (AJOL)

    Kinetic studies of anaerobic digestion process of cheese whey were conducted in a pilot-scale up-flow anaerobic packed bed bioreactor (UAPB). An influent COD concentration of 59419 mg/l was utilized at steady state condition. Logistic and Monod kinetic models were employed to describe microbial activities of cheese ...

  10. Influence of decelerating flow on incipient motion of a gravel-bed ...

    Indian Academy of Sciences (India)

    Influence of decelerating flow on incipient motion of a gravel-bed stream. HOSSEIN AFZALIMHR. ∗,1. , SUBHASISH DEY. 2 and. POONEH RASOULIANFAR. 1. 1Department of Water Engineering, Isfahan University of Technology, Isfahan, Iran. 2Department of Civil Engineering, Indian Institute of Technology,. Kharagpur ...

  11. Dispersed plug flow model for upflow anaerobic sludge bed reactors with focus on granular sludge dynamics

    NARCIS (Netherlands)

    Kalyuzhnyi, S.V.; Fedorovich, V.V.; Lens, P.N.L.

    2006-01-01

    A new approach to model upflow anaerobic sludge bed (UASB)-reactors, referred to as a one-dimensional dispersed plug flow model, was developed. This model focusses on the granular sludge dynamics along the reactor height, based on the balance between dispersion, sedimentation and convection using

  12. PEBBLES: A COMPUTER CODE FOR MODELING PACKING, FLOW AND RECIRCULATIONOF PEBBLES IN A PEBBLE BED REACTOR

    Energy Technology Data Exchange (ETDEWEB)

    Joshua J. Cogliati; Abderrafi M. Ougouag

    2006-10-01

    A comprehensive, high fidelity model for pebble flow has been developed and embodied in the PEBBLES computer code. In this paper, a description of the physical artifacts included in the model is presented and some results from using the computer code for predicting the features of pebble flow and packing in a realistic pebble bed reactor design are shown. The sensitivity of models to various physical parameters is also discussed.

  13. Wall roughness effects on flow and scouring in curved channels with gravel bed

    OpenAIRE

    Hersberger, Daniel S.

    2002-01-01

    Wall roughness effects on flow and scouring in curved channels with gravel bed In the narrow valleys in Alpine regions, rivers frequently flow across constructed zones, passing through villages and cities. Due to limited space, the protection from high floods often needs to be ensured by protection walls. During floods, these protection walls may be endangered by scour phenomena, especially if they are located in bends. In the past, the potential danger of underscoured structures was reduced ...

  14. A Conceptual Framework for Improving Critical Care Patient Flow and Bed Use.

    Science.gov (United States)

    Mathews, Kusum S; Long, Elisa F

    2015-06-01

    High demand for intensive care unit (ICU) services and limited bed availability have prompted hospitals to address capacity planning challenges. Simulation modeling can examine ICU bed assignment policies, accounting for patient acuity, to reduce ICU admission delays. To provide a framework for data-driven modeling of ICU patient flow, identify key measurable outcomes, and present illustrative analysis demonstrating the impact of various bed allocation scenarios on outcomes. A description of key inputs for constructing a queuing model was outlined, and an illustrative simulation model was developed to reflect current triage protocol within the medical ICU and step-down unit (SDU) at a single tertiary-care hospital. Patient acuity, arrival rate, and unit length of stay, consisting of a "service time" and "time to transfer," were estimated from 12 months of retrospective data (n = 2,710 adult patients) for 36 ICU and 15 SDU staffed beds. Patient priority was based on acuity and whether the patient originated in the emergency department. The model simulated the following hypothetical scenarios: (1) varied ICU/SDU sizes, (2) reserved ICU beds as a triage strategy, (3) lower targets for time to transfer out of the ICU, and (4) ICU expansion by up to four beds. Outcomes included ICU admission wait times and unit occupancy. With current bed allocation, simulated wait time averaged 1.13 (SD, 1.39) hours. Reallocating all SDU beds as ICU decreased overall wait times by 7.2% to 1.06 (SD, 1.39) hours and increased bed occupancy from 80 to 84%. Reserving the last available bed for acute patients reduced wait times for acute patients from 0.84 (SD, 1.12) to 0.31 (SD, 0.30) hours, but tripled subacute patients' wait times from 1.39 (SD, 1.81) to 4.27 (SD, 5.44) hours. Setting transfer times to wards for all ICU/SDU patients to 1 hour decreased wait times for incoming ICU patients, comparable to building one to two additional ICU beds. Hospital queuing and simulation modeling

  15. Friction factor for water flow through packed beds of spherical and non-spherical particles

    Directory of Open Access Journals (Sweden)

    Kaluđerović-Radoičić Tatjana

    2017-01-01

    Full Text Available The aim of this work was the experimental evaluation of different friction factor correlations for water flow through packed beds of spherical and non-spherical particles at ambient temperature. The experiments were performed by measuring the pressure drop across the bed. Packed beds made of monosized glass spherical particles of seven different diameters were used, as well as beds made of 16 fractions of quartz filtration sand obtained by sieving (polydisperse non-spherical particles. The range of bed voidages was 0.359–0.486, while the range of bed particle Reynolds numbers was from 0.3 to 286 for spherical particles and from 0.1 to 50 for non-spherical particles. The obtained results were compared using a number of available literature correlations. In order to improve the correlation results for spherical particles, a new simple equation was proposed in the form of Ergun’s equation, with modified coefficients. The new correlation had a mean absolute deviation between experimental and calculated values of pressure drop of 9.04%. For non-spherical quartz filtration sand particles the best fit was obtained using Ergun’s equation, with a mean absolute deviation of 10.36%. Surface-volume diameter (dSV necessary for correlating the data for filtration sand particles was calculated based on correlations for dV = f(dm and Ψ = f(dm. [Project of the Serbian Ministry of Education, Science and Technological Development, Grant no. ON172022

  16. A CFD Study on Inlet Plenum Flow Field of Pebble Bed Reactor

    International Nuclear Information System (INIS)

    Kim, Min Hwan; Lee, Won Jae; Chang, Jong Hwa

    2005-01-01

    High temperature gas cooled reactor, largely divided into two types of PBR (Pebble Bed Reactor) and PMR (Prismatic Modular Reactor), has becomes great interest of researchers in connection with the hydrogen production. KAERI has started a project to develop the gas cooled reactor for the hydrogen production and has been doing in-depth study for selecting the reactor type between PBR and PMR. As a part of the study, PBMR (Pebble Bed Modular Reactor) was selected as a reference PBR reactor for the CFD analysis and the flow field of its inlet plenum was simulated with computational fluid dynamics program CFX5. Due to asymmetrical arrangement of pipes to the inlet plenum, non-uniform flow distribution has been expected to occur, giving rise to non-uniform power distribution at the core. Flow fields of different arrangement of inlet pipes were also investigated, as one of measures to reduce the non-uniformity

  17. Quasi-direct numerical simulation of a pebble bed configuration. Part I: Flow (velocity) field analysis

    International Nuclear Information System (INIS)

    Shams, A.; Roelofs, F.; Komen, E.M.J.; Baglietto, E.

    2013-01-01

    Highlights: ► Quasi direct numerical simulations (q-DNS) of a pebble bed configuration has been performed. ► This q-DNS database may serve as a reference for the validation of different turbulence modeling approaches. ► A wide range of qualitative and quantitative data throughout the computational domain has been generated. ► Results for mean, RMS and covariance of velocity field are extensively reported in this paper. -- Abstract: High temperature reactors (HTR) are being considered for deployment around the world because of their excellent safety features. The fuel is embedded in a graphite moderator and can sustain very high temperatures. However, the appearance of hot spots in the pebble bed cores of HTR's may affect the integrity of the pebbles. A good prediction of the flow and heat transport in such a pebble bed core is a challenge for available turbulence models and such models need to be validated. In the present article, quasi direct numerical simulations (q-DNS) of a pebble bed configuration are reported, which may serve as a reference for the validation of different turbulence modeling approaches. Such approaches can be used in order to perform calculations for a randomly arranged pebble bed. Simulations are performed at a Reynolds number of 3088, based on pebble diameter, with a porosity level of 0.42. Detailed flow analyses have shown complex physics flow behavior and make this case challenging for turbulence model validation. Hence, a wide range of qualitative and quantitative data for velocity and temperature field have been extracted for this benchmark. In the present article (part I), results related to the flow field (mean, RMS and covariance of velocity) are documented and discussed in detail. Moreover, the discussion regarding the temperature field will be published in a separate article

  18. Bed Surface Responses to Spatially Variable Flow in Low Relative Submergence Conditions

    Science.gov (United States)

    Monsalve Sepulveda, A.; Yager, E.

    2017-12-01

    Flow hydraulics and sediment fluxes in mountainous rivers are partly controlled by large relatively immobile grains and sediment patches. Generally, in these rivers the flow depth is similar to the size of these large grains (low relative submergence), and is characterized by 3D heterogeneity and plunging flow that can cause spatial distributions of bed surface elevations, textures, and sedimentation rates. Sediment patches, on the other hand, consist of distinct areas of the bed with relatively narrow grain size distributions (GSD) and greater sorting compared to that of the reach, can cause spatial distributions of flow properties, and therefore, a continuous feedback between them and flow hydraulics exists and partially controls the evolution of a river. Although sediment-water interactions are affected by sediment patches, they are rarely explicitly included in bedload transport calculations, in part because their formation and evolution are controlled by highly temporal and spatially variable mechanisms, such as shear stress fields, flow discharges, turbulence, and local GSD. To explore how the bed surface evolves and sediment patches are formed, we conducted a set of experiments in which we varied the relative submergence (RS) of staggered simulated boulders between runs. All experiments had the same average sediment transport capacity, upstream sediment supply, and initial gravel bed thickness and GSD. Different RS between experiments were achieved by simultaneously adjusting flow discharge and bed slope (2.15 - 3.7 %). To obtain a detailed flow field we combined our laboratory measurements with a 3D flow model. Around the boulders, the shear stress field was highly variable and controlled the sediment flux rates and its direction. The divergence in shear stress caused by the boulders promoted size-selective bedload deposition, which in some cases resulted in the formation of a coarse sediment patch upstream of the boulders but, for the higher slopes, a bar

  19. Gravity-driven, dry granular flows over a loose bed in stationary and homogeneous conditions

    Science.gov (United States)

    Meninno, Sabrina; Armanini, Aronne; Larcher, Michele

    2018-02-01

    Flows involving solid particulates have been widely studied in recent years, but their dynamics are still a complex issue to model because they strongly depend on the interaction with the boundary conditions. We report on laboratory investigations regarding homogeneous and steady flows of identical particles over a loose bed in a rectangular channel. Accurate measurements were carried out through imaging techniques to estimate profiles of the mean velocity, solid concentration, and granular temperature for a large set of flow rates and widths. Vertical and transversal structures observed in the flow change as interparticle interactions become more collisional, and they depend on the bottom over which the flow develops. The lateral confinement has a remarkable effect on the flow, especially for narrow channels compared with the grain size, and a hydraulic analogy is able to show how the walls influence the mechanisms of friction and energy dissipation.

  20. CFD Flow and Heat Transfer Simulation for Empty and Packed Fixed Bed Reactor in Catalytic Cracking of Naphtha

    OpenAIRE

    D. Salari; A. Niaei; P. Chitsaz Yazdi; M. Derakhshani; S. R. Nabavi

    2007-01-01

    This work aims to test the application of computational fluid dynamics (CFD) modeling to fixed bed catalytic cracking reactors. Studies of CFD with a fixed bed design commonly use a regular packing with N=2 to define bed geometry. CFD allows us to obtain a more accurate view of the fluid flow and heat transfer mechanisms present in fixed bed equipment. Naphtha was used as feedstock and the reactor length was 80cm. It is divided in three sections that catalyst bed packed in the middle section ...

  1. Heat transfer and flow characteristics around a finned-tube bank heat exchanger in fluidized bed

    Energy Technology Data Exchange (ETDEWEB)

    Honda, Ryosuke [Department of Mechanical Engineering, Kansai University, 3-3-35 Yamate-cho, Suita, Osaka 564-8680 (Japan); Umekawa, Hisashi [Department of Mechanical Engineering, Kansai University, 3-3-35 Yamate-cho, Suita, Osaka 564-8680 (Japan)], E-mail: umekawa@kansai-uac.jp; Ozawa, Mamoru [Department of Mechanical Engineering, Kansai University, 3-3-35 Yamate-cho, Suita, Osaka 564-8680 (Japan)

    2009-06-21

    Principal heat transfer mechanisms in a fluidized bed have been classified into three categories, i.e. solid convection, gas convection and radiation. Among these mechanisms, the solid convection is a dominant mechanism in the bubbling fluidized bed. This solid convection is substantially caused by the bubble movement, thus the visualization of the void fraction distribution becomes a very useful method to understand the characteristics of the fluidized-bed heat exchanger. In this study, the heat transfer coefficient and the void fraction around the heat transfer tube with annuler fin were measured. For the quantitative measurement of the void fraction, neutron radiography and image processing technique were employed. Owing to the existence of the annuler fin, the restriction of the particle movements was put. This restriction suppressed the disturbance caused by tubes, and the influence of the tube arrangement on the flow and heat transfer characteristics could be clearly expressed.

  2. Heat transfer and flow characteristics around a finned-tube bank heat exchanger in fluidized bed

    International Nuclear Information System (INIS)

    Honda, Ryosuke; Umekawa, Hisashi; Ozawa, Mamoru

    2009-01-01

    Principal heat transfer mechanisms in a fluidized bed have been classified into three categories, i.e. solid convection, gas convection and radiation. Among these mechanisms, the solid convection is a dominant mechanism in the bubbling fluidized bed. This solid convection is substantially caused by the bubble movement, thus the visualization of the void fraction distribution becomes a very useful method to understand the characteristics of the fluidized-bed heat exchanger. In this study, the heat transfer coefficient and the void fraction around the heat transfer tube with annuler fin were measured. For the quantitative measurement of the void fraction, neutron radiography and image processing technique were employed. Owing to the existence of the annuler fin, the restriction of the particle movements was put. This restriction suppressed the disturbance caused by tubes, and the influence of the tube arrangement on the flow and heat transfer characteristics could be clearly expressed.

  3. Investigation of flow mechanisms in conical models of fluidized beds and transfer of the results to high-temperature-coating beds. A study on the coating of nuclear fuel particles in fluidized beds

    International Nuclear Information System (INIS)

    Kalthoff, B.; Gyarmati, E.; Nickel, H.

    The different states of movement of the fluid-solid particle system as occurring in coating of nuclear particle fuel in conical fluidized beds determine the transfer of momentum, heat and mass in the fluidized bed. To know the flow characteristics, therefore, is essential for the understanding of the complex processes which take place during coating. As experimental studies in actual coaters initially were impossible due to the high temperature levels of up to 2000 0 C, information on characteristic behavior of the fluidized bed was obtained from geometrically similar model beds. Based on principles in the mechanics of similarity the fluid-solid particle system was selected. Hence, results obtained in model tests could be correlated to hot fluidized beds by means of a dimensionless characteristic number describing the fluid-solid system. A second combination of characteristic numbers allows the characterization of the three states of a fluidizing regime, i.e., spouting, bubbling, and slugging. For examining the model test results in hot beds, a measuring device was developed applicable to both cold model beds and actual fluidized bed coaters; pressure oscillations originating in the beds could be made visible by means of electronics and their frequency measured. Coating experiments with different batches and at different temperature levels rendered this frequency to decrease with increase in bed height. Thus the frequency is an important index for the momentary state of fluidization of the fluid-solid particle system. (U.S.)

  4. Dryout heat flux in a debris bed with forced coolant flow from below

    International Nuclear Information System (INIS)

    Bang, Kwang-Hyun; Kim, Jong-Myung

    2004-01-01

    The objective of the present study is to experimentally investigate the enhancement of dryout heat flux in debris beds with coolant flow from below. The experimental facility consists mainly of an induction heater (40 kW, 35 kHz), a double-wall quartz-tube test section containing steel-particle bed and coolant injection and recovery condensing loop. A fairly uniform heating of particle bed was achieved by induction heating. This paper reports the experimental data for 5 mm particle bed and 300 mm bed height. The dryout heat rate data were obtained of both top-flooding case and forced coolant injection from below with the injection mass flux up to 1.5 kg/m 2 s. For the top-flooded case, the volumetric dryout heat rate was about 4 MW/m 3 and it increased as the rate of coolant injection from below was increased. At the coolant injection mass flux of 1.5 kg/m 2 s, the volumetric dryout heat rate was about 10 MW/m 3 , the enhancement factor was more than two. (author)

  5. Saving reed lands by giving economic value to reed

    Directory of Open Access Journals (Sweden)

    F.W. Croon

    2014-07-01

    Full Text Available Discussions about the need for renewable energy, the need for nature conservation, the need to double the world’s food production to eliminate hunger, the need to reduce carbon dioxide emission, and the wish to reduce dependency on dwindling oil resources, show that these issues are intimately related and sometimes mutually exclusive. The use of food crops for the production of renewable fuels has resulted in the energy vs. food debate; the use of scarce land and fresh water for the dedicated production of biomass conflicts with food production and nature conservation; the collection of harvest residues and forest wastes as biomass to produce renewable fuels is complex and leaves a CO2 footprint. The several species of reed that grow naturally in deltas, river plains etc. can provide large amounts of biomass but are hardly mentioned in the debates. Harvesting reed does not threaten the nature and the natural functions of reed lands, which are carbon neutral or carbon dioxide sinks. Reed production does not need extensive infrastructure or complex cultivation and does not compete with food production for land and fresh water. Reed lands in many places are under threat of reclamation for economic activities and urbanisation. This trend can be countered if reed is seen to have a proven economic value. In this article I argue that giving a sustainable economic value to reed lands can only be realised if the exploitation is recognised as being environmentally acceptable, commercially feasible and a source of economic gains for all stakeholders. Commercial feasibility can be achieved under present economic conditions only if a reliable supply of considerable volumes of reed at a limited price can be guaranteed.

  6. Bulk stress distributions in the pore space of sphere-packed beds under Darcy flow conditions.

    Science.gov (United States)

    Pham, Ngoc H; Voronov, Roman S; Tummala, Naga Rajesh; Papavassiliou, Dimitrios V

    2014-03-01

    In this paper, bulk stress distributions in the pore space of columns packed with spheres are numerically computed with lattice Boltzmann simulations. Three different ideally packed and one randomly packed configuration of the columns are considered under Darcy flow conditions. The stress distributions change when the packing type changes. In the Darcy regime, the normalized stress distribution for a particular packing type is independent of the pressure difference that drives the flow and presents a common pattern. The three parameter (3P) log-normal distribution is found to describe the stress distributions in the randomly packed beds within statistical accuracy. In addition, the 3P log-normal distribution is still valid when highly porous scaffold geometries rather than sphere beds are examined. It is also shown that the 3P log-normal distribution can describe the bulk stress distribution in consolidated reservoir rocks like Berea sandstone.

  7. The origin of granular convection in vertically vibrated particle beds: The differential shear flow field.

    Science.gov (United States)

    Xue, Kun; Zheng, Yixin; Fan, Baolong; Li, Fangfang; Bai, Chunhua

    2013-01-01

    This paper investigates the particle scale dynamics of granular convection in vertically vibrated granular beds. The onset of the convection is found to coincide with the noticeable particle transverse migrations from the side walls towards the centre of the bed, which only take place in the wake of the gravity wave front dividing the upward moving particles and the falling ones. The mechanism driving the particle inward flows and thus sustaining the complete convection rolls can be understood in light of a convection model based on void penetration. This stochastic convection model reveals that the underlying driving force is a distinctive differential shear flow field arising from the combined effect of frictional holdback by the walls and the downward pull of gravity. The changes of the convection pattern with inceasing acceleration amplitude, in terms of the convection strength and the thickness of the bottom of the convection rolls, can be accounted for by this model.

  8. Evaluation of a commercial packed bed flow hydrogenator for reaction screening, optimization, and synthesis

    Directory of Open Access Journals (Sweden)

    Marian C. Bryan

    2011-08-01

    Full Text Available The performance of the ThalesNano H-Cube®, a commercial packed bed flow hydrogenator, was evaluated in the context of small scale reaction screening and optimization. A model reaction, the reduction of styrene to ethylbenzene through a 10% Pd/C catalyst bed, was used to examine performance at various pressure settings, over sequential runs, and with commercial catalyst cartridges. In addition, the consistency of the hydrogen flow was indirectly measured by in-line UV spectroscopy. Finally, system contamination due to catalyst leaching, and the resolution of this issue, is described. The impact of these factors on the run-to-run reproducibility of the H-Cube® reactor for screening and reaction optimization is discussed.

  9. Improving flow properties of ibuprofen by fluidized bed particle thin-coating.

    Science.gov (United States)

    Ehlers, Henrik; Räikkönen, Heikki; Antikainen, Osmo; Heinämäki, Jyrki; Yliruusi, Jouko

    2009-02-23

    The surfaces of ibuprofen particles (d(50) 42 microm) were modified by coating the particles with diluted aqueous hydroxypropyl methylcellulose (HPMC) solution in an instrumentated top-spray fluid bed granulator. The objective was to evaluate whether an extremely thin polymer coating could be an alternative to granulation in enhancing powder flow and processing properties. The studied variables were inlet air temperature and spray rate. The treated powders showed a clear improvement in flow rate as measured with a flow meter designed for powders with poor flow properties. The particle size was determined using optical microscopy and image analysis. The particle size, size distribution and circularity of the treated and untreated ibuprofen batches showed no difference from each other. Consequently, the improvement in flow properties can be attributed to the trace amounts of hydroxypropyl methylcellulose applied onto the particle surfaces. In conclusion, fluidized bed particle thin-coating (PTC) alters the surface of ibuprofen powder particles and improves the flow properties of ibuprofen powder with changes in neither particle size, size distribution nor morphology.

  10. Visualizations of the disturbed-laminar wave-induced flow above a rippled bed

    Science.gov (United States)

    Ourmières, Y.; Chaplin, J. R.

    This paper discusses visualizations of wave-induced flow over a rippled bed. Experiments were conducted in a wave tank fitted with a rigid rippled bed, and flow visualizations were carried out using a fluorescent dye filmed by a digital high speed video camera. Secondary flow regimes are classified in terms of key parameters such as the ripple slope, the ratio of the amplitude of the external flow to the ripple wavelength, and a Taylor number. For weak oscillations over gentle ripples, two-dimensional structures develop in the form of large recirculation cells, while for stronger flows over medium to steep ripples these are modified by the onset of separation and vortex shedding. Three-dimensional instabilities lead to disturbed-laminar flow structures of two different forms. The most common and stable form is a structure of rings that has a well-defined transverse wavelength that is found to be inversely proportional to a Taylor number. The other form, a brick pattern, is more transient in nature but is probably also related to the development of three-dimensional ripple shapes.

  11. On dryout heat flux and pressure drop of a submerged inductively heated bed flow from below

    International Nuclear Information System (INIS)

    Tsai, F.F.; Catton, I.

    1983-01-01

    An experimental investigation of dryout heat flux in a saturated porous medal with forced flow from below has been conducted using methanol as a coolant. The mass flux varied from 0 to 0.557 kg/m 2 sec. Particle sizes were 590-790 μm, 1.6 mm, 3.2 mm, and 4.8 mm. The dryout heat flux increases as the mass flux increases, and asymptotically goes to the total evaporation energy of the inlet flow. The pressure drop across the bed changed very rapidly near the dryout point due to the formation of dry zone

  12. CFD Modeling of Flow and Ion Exchange Kinetics in a Rotating Bed Reactor System

    DEFF Research Database (Denmark)

    Larsson, Hilde Kristina; Schjøtt Andersen, Patrick Alexander; Byström, Emil

    2017-01-01

    be achieved by making the baffles deeper. Two-phase simulations were performed, which managed to reproduce the deflection of the gas–liquid interface in an unbaffled system. A chemical reaction was implemented in the model, describing the ion-exchange phenomena in the porous material using four different......A rotating bed reactor (RBR) has been modeled using computational fluid dynamics (CFD). The flow pattern in the RBR was investigated and the flow through the porous material in it was quantified. A simplified geometry representing the more complex RBR geometry was introduced and the simplified...... model was able to reproduce the main characteristics of the flow. Alternating reactor shapes were investigated, and it was concluded that the use of baffles has a very large impact on the flows through the porous material. The simulations suggested, therefore, that even faster reaction rates could...

  13. Experimental and computational investigation of flow of pebbles in a pebble bed nuclear reactor

    Science.gov (United States)

    Khane, Vaibhav B.

    The Pebble Bed Reactor (PBR) is a 4th generation nuclear reactor which is conceptually similar to moving bed reactors used in the chemical and petrochemical industries. In a PBR core, nuclear fuel in the form of pebbles moves slowly under the influence of gravity. Due to the dynamic nature of the core, a thorough understanding about slow and dense granular flow of pebbles is required from both a reactor safety and performance evaluation point of view. In this dissertation, a new integrated experimental and computational study of granular flow in a PBR has been performed. Continuous pebble re-circulation experimental set-up, mimicking flow of pebbles in a PBR, is designed and developed. Experimental investigation of the flow of pebbles in a mimicked test reactor was carried out for the first time using non-invasive radioactive particle tracking (RPT) and residence time distribution (RTD) techniques to measure the pebble trajectory, velocity, overall/zonal residence times, flow patterns etc. The tracer trajectory length and overall/zonal residence time is found to increase with change in pebble's initial seeding position from the center towards the wall of the test reactor. Overall and zonal average velocities of pebbles are found to decrease from the center towards the wall. Discrete element method (DEM) based simulations of test reactor geometry were also carried out using commercial code EDEM(TM) and simulation results were validated using the obtained benchmark experimental data. In addition, EDEM(TM) based parametric sensitivity study of interaction properties was carried out which suggests that static friction characteristics play an important role from a packed/pebble beds structural characterization point of view. To make the RPT technique viable for practical applications and to enhance its accuracy, a novel and dynamic technique for RPT calibration was designed and developed. Preliminary feasibility results suggest that it can be implemented as a non

  14. A model for complex flows of soft glassy materials with application to flows through fixed fiber beds

    International Nuclear Information System (INIS)

    Sarkar, Arijit; Koch, Donald L.

    2015-01-01

    The soft glassy rheology (SGR) model has successfully described the time dependent simple shear rheology of a broad class of complex fluids including foams, concentrated emulsions, colloidal glasses, and solvent-free nanoparticle-organic hybrid materials (NOHMs). The model considers a distribution of mesoscopic fluid elements that hop from trap to trap at a rate which is enhanced by the work done to strain the fluid element. While an SGR fluid has a broad exponential distribution of trap energies, the rheology of NOHMs is better described by a narrower energy distribution and we consider both types of trap energy distributions in this study. We introduce a tensorial version of these models with a hopping rate that depends on the orientation of the element relative to the mean stress field, allowing a range of relative strengths of the extensional and simple shear responses of the fluid. As an application of these models we consider the flow of a soft glassy material through a dilute fixed bed of fibers. The dilute fixed bed exhibits a range of local linear flows which alternate in a chaotic manner with time in a Lagrangian reference frame. It is amenable to an analytical treatment and has been used to characterize the strong flow response of many complex fluids including fiber suspensions, dilute polymer solutions and emulsions. We show that the accumulated strain in the fluid elements has an abrupt nonlinear growth at a Deborah number of order one in a manner similar to that observed for polymer solutions. The exponential dependence of the hopping rate on strain leads to a fluid element deformation that grows logarithmically with Deborah number at high Deborah numbers. SGR fluids having a broad range of trap energies flowing through fixed beds can exhibit a range of rheological behaviors at small Deborah numbers ranging from a yield stress, to a power law response and finally to Newtonian behavior

  15. A model for complex flows of soft glassy materials with application to flows through fixed fiber beds

    KAUST Repository

    Sarkar, Arijit

    2015-11-01

    © 2015 The Society of Rheology. The soft glassy rheology (SGR) model has successfully described the time dependent simple shear rheology of a broad class of complex fluids including foams, concentrated emulsions, colloidal glasses, and solvent-free nanoparticle-organic hybrid materials (NOHMs). The model considers a distribution of mesoscopic fluid elements that hop from trap to trap at a rate which is enhanced by the work done to strain the fluid element. While an SGR fluid has a broad exponential distribution of trap energies, the rheology of NOHMs is better described by a narrower energy distribution and we consider both types of trap energy distributions in this study. We introduce a tensorial version of these models with a hopping rate that depends on the orientation of the element relative to the mean stress field, allowing a range of relative strengths of the extensional and simple shear responses of the fluid. As an application of these models we consider the flow of a soft glassy material through a dilute fixed bed of fibers. The dilute fixed bed exhibits a range of local linear flows which alternate in a chaotic manner with time in a Lagrangian reference frame. It is amenable to an analytical treatment and has been used to characterize the strong flow response of many complex fluids including fiber suspensions, dilute polymer solutions and emulsions. We show that the accumulated strain in the fluid elements has an abrupt nonlinear growth at a Deborah number of order one in a manner similar to that observed for polymer solutions. The exponential dependence of the hopping rate on strain leads to a fluid element deformation that grows logarithmically with Deborah number at high Deborah numbers. SGR fluids having a broad range of trap energies flowing through fixed beds can exhibit a range of rheological behaviors at small Deborah numbers ranging from a yield stress, to a power law response and finally to Newtonian behavior.

  16. 2-Dimensional Numerical Analysis of Flow and Bed Evolution in Open-Channel Bends with Cylindrical Roughness

    OpenAIRE

    冨永, 晃宏; 青木, 健太郎

    2001-01-01

    Vegetation in a river has a similar effect as permeable super dikes. Such an effect can be substituted by a group of cylindrical roughness. In this study, 3-dimensional flow structures and bed evolution were measured in a curved open channel with cylindrical roughness located along the outer bank. A series of cylinder decreased the scour at the outer bank. Especially submerged cylindrical roughness can reduce the bed evolution much more. Flow structures over the submerged cylindrical roughnes...

  17. Large-eddy simulation of the flow over a hydrokinetic turbine mounted on an erodible bed

    Science.gov (United States)

    Yang, Xiaolei; Khosronejad, Ali; Sotiropoulos, Fotis

    2013-11-01

    Marine and hydrokinetic (MHK) energy comprises an important source of clean and renewable energy. The beds of natural waterways are usually erodible. The hydrokinetic turbines affect the sediment transport, which, on the other hand, also influences the performance of hydrokinetic turbines. A powerful computational framework for simulating marine and hydrokinetic (MHK) turbine arrays mounted in complex river bathymetry with sediment transport has been developed and validated by our group. In this work we apply this method to simulate the turbulent flow over a hydrokinetic turbine mounted in an open channel with erodible bed. Preliminary results show qualitatively good agreement with the experiment. Detailed comparison with measurements and analysis of the simulation results will be presented in the conference. This work was supported by the University of Minnesota Initiative for Renewable Energy and the Environment IREE (grant no RO-0004-12). Computational resources were provided by the University of Minnesota Supercomputing Institute.

  18. Magnetic resonance velocity imaging of liquid and gas two-phase flow in packed beds.

    Science.gov (United States)

    Sankey, M H; Holland, D J; Sederman, A J; Gladden, L F

    2009-02-01

    Single-phase liquid flow in porous media such as bead packs and model fixed bed reactors has been well studied by MRI. To some extent this early work represents the necessary preliminary research to address the more challenging problem of two-phase flow of gas and liquid within these systems. In this paper, we present images of both the gas and liquid velocities during stable liquid-gas flow of water and SF(6) within a packing of 5mm spheres contained within columns of diameter 40 and 27 mm; images being acquired using (1)H and (19)F observation for the water and SF(6), respectively. Liquid and gas flow rates calculated from the velocity images are in agreement with macroscopic flow rate measurements to within 7% and 5%, respectively. In addition to the information obtained directly from these images, the ability to measure liquid and gas flow fields within the same sample environment will enable us to explore the validity of assumptions used in numerical modelling of two-phase flows.

  19. Numerical Simulation of a Coolant Flow and Heat Transfer in a Pebble Bed Reactor

    International Nuclear Information System (INIS)

    In, Wang-Kee; Kim, Min-Hwan; Lee, Won-Jae

    2008-01-01

    Pebble Bed Reactor(PBR) is one of the very high temperature gas cooled reactors(VHTR) which have been reviewed in the Generation IV International Forum as potential sources for future energy needs, particularly for a hydrogen production. The pebble bed modular reactor(PBMR) exhibits inherent safety features due to the low power density and the large amount of graphite present in the core. PBR uses coated fuel particles(TRISO) embedded in spherical graphite fuel pebbles. The fuel pebbles flow down through the PBR core during a reactor operation and the coolant flows around randomly distributed spheres. For the reliable operation and the safety of the PBR, it is important to understand the coolant flow structure and the fuel pebble temperature in the PBR core. There have been few experimental and numerical studies to investigate the fluid and heat transfer phenomena in the PBR core. The objective of this paper is to predict the fluid and heat transfer in the PBR core. The computational fluid dynamics (CFD) code, STAR-CCM+(V2.08) is used to perform the CFD analysis using the design data for the PBMR400

  20. Technology test bed and hydrogen cold flow facilities at the Marshall Space Flight Center

    Science.gov (United States)

    Lightfoot, Robert; Gautney, Tim

    1993-01-01

    The Technology Test Bed and Hydrogen Cold Flow facilities at NASA's Marshall Space Flight Center (MSFC) in Huntsville, Alabama provide unique testing capabilities for the aerospace community. Located at the Advanced Engine Test Facility (AETF), these facilities are operated and maintained by MSFC Propulsion Laboratory personnel. They provide a systems and components level testing platform for validating new technology concepts and advanced systems design and for gaining a better understanding of the test article internal environments. A discussion follows of the particular capabilities of each facility to provide a range of testing options for specific test articles.

  1. Evaluation of alkalinity spatial distribution in an up-flow fixed bed anaerobic digester.

    Science.gov (United States)

    Hmissi, Maha; Harmand, Jérôme; Alcaraz-Gonzalez, Victor; Shayeb, Hedi

    2018-02-01

    In this paper, an experimental study upon alkalinity and hydrodynamic behavior in an anaerobic up-flow fixed bed reactor for the treatment of tequila vinasses is presented. Measurements of volatile fatty acids, pH, alkalinity and bicarbonate were obtained at three sampling points in the reactor in the axial axis. Then, the spatial distribution of alkalinity is studied and discussed. Moreover, for further control process purposes, a hydrodynamic model based on the use of two interconnected two-steps reduced AM2 type models is proposed and its parameters are identified using experimental data.

  2. Numerical investigation of the flow at the pebble bed of the high temperature gas cooled reactors

    International Nuclear Information System (INIS)

    Costa, Franklin C.; Navarro, Moyses A.; Santos, Andre A.C.

    2011-01-01

    This paper presents a numerical investigation of the thermal and fluid dynamics among the fuel spheres and the cooling fluid, appearing in the core of pebble bed reactor (PBR-Peeble Bed Reactor) using the CFD-Computational Fluid Dynamics CFX 13.0. The paper presents the two analysis results. In the first phase it was considered two heat transfer models for the fuel spheres. In a model it was established volumetric load generation, with thermal conduction for both the fuel and coating. The other model prescribes a heat flux at the sphere surfaces. In this analysis, it was proceed two simulation in the two sphere arrangements, one considering the spheres in contact, and the other with 2 mm spacing between them. At the second analysis it was evaluated the sphere arrangement influence on the thermal and fluid dynamic behavior of the bed. The four simulations present differences in the flow and in the surface and maximum temperature profiles of the coating.(author)

  3. The study on three-dimensional mathematical model of river bed erosion for water-sediment two-phase flow

    Science.gov (United States)

    Fang, Hongwei

    1996-02-01

    Based on the tensor analysis of water-sediment two-phase flow, the basic model equations for clear water flow and sediment-laden flow are deduced in the general curve coordinates for natural water variable-density turbulent flow. Furthermore, corresponding boundary conditions are also presented in connection with the composition and movement of non-uniform bed material. The theoretical results are applied to the calculation of the float open caisson in the construction period and good results are obtained.

  4. Characterization of bed load discharge in unsteady flow events in an ephemeral channel

    Science.gov (United States)

    Halfi, Eran

    2017-04-01

    There are many methods and equations for estimating bedload flux in steady flow conditions. Yet, very little is known about the effect of very unsteady flows, such as flash floods, on bedload flux. The unpredictable nature of the floods together with many logistic difficulties and safety issues in monitoring explain this gap in knowledge. Global climate change may increase flood event occurrence, making their understanding even more crucial. This research focuses on two durations of flash floods where the flow is most rapidly changing: a) flash flood bore arriving on dry river bed and b) flash flood bore arriving on a column of moving water. The methodology of our study is based on the demonstrated ability of the Eshtemoa gauging station to automatically monitor the variation of bedload flux depending on flow and bed characteristics, along with innovative equipment including hydrophones and geophones for capturing acoustic signals of bedload sediments (1 Hz), video cameras for continuous monitoring of water surface velocity (by the LSPIV method to determine its structure and velocity) and 3-D velocimetry for characterizing turbulence (40 Hz). Additional to these, a well-planned deployment was carried out, including alerting sensors and cellular transmission, enabling to be onsite when bores arrive. During the winter of 2015-2016 two flow events were sufficiently large to transport significant amounts of bedload; the magnitude of the larger event occurs once in a few years. Calibration between the acoustic indirect sensor and the direct slot sampler allow determination of bedload flux at a frequency of 1 Hz. Analyses of the two events indicate an increase of the turbulent nature (increase of the turbulent kinetic energy and the instantaneous vertical velocities), shear stress and bedload flux during the rising limb in the first two minutes of bore arrival.

  5. Coupled dynamics of the co-evolution of gravel bed topography, flow turbulence and sediment transport in an experimental channel

    Science.gov (United States)

    Singh, Arvind; Foufoula-Georgiou, Efi; Porté-Agel, Fernando; Wilcock, Peter R.

    2012-12-01

    A series of flume experiments were conducted in a large experimental channel at the St. Anthony Falls Laboratory to understand the coupled dynamics of flow and bed forms above the sediment-water interface. Simultaneous high resolution measurements of velocity fluctuations, bed elevations and sediment flux at the downstream end of the channel, were made for a range of discharges. The probability density functions (pdfs) of bed elevation increments and instantaneous Reynolds stress reveal a power law tail behavior and a wavelet cross-correlation analysis depicts a strong dependence of these series across a range of scales, indicating a feedback between bed form dynamics and near-bed turbulence. These results complement our previous findings in which the signature of bed form evolution on the near-bed velocity fluctuations was confirmed via the presence of a spectral gap and two distinct power law scaling regimes in the spectral density of velocity fluctuations. We report herein a strong asymmetry in the probability distribution of bed elevation increments and instantaneous Reynolds stresses, the latter being further analyzed and interpreted via a quadrant analysis of velocity fluctuations in the longitudinal and vertical directions. We also report the presence of intermittency (multifractality) in bed elevation increments and interpret it, in view of the asymmetric nature of the pdfs, as the result of scale coupling. In other words, the geometric asymmetry at the bed form scale gets transferred down to a probabilistic asymmetry at all smaller scales indicating a local anisotropy in the energy transfer. Finally, we propose a predictive relationship between bed form averaged sediment transport rates and bed form averaged instantaneous Reynolds stress and validate it using our experimental data.

  6. Heat-transfer characteristics of flowing and stationary particle-bed-type fusion-reactor blankets

    Energy Technology Data Exchange (ETDEWEB)

    Nietert, R.E.

    1983-02-01

    The following five appendices are included: (1) physical properties of materials, (2) thermal entrance length Nusselt number variations, (3) stationary particle bed temperature variations, (4) falling bed experimental data and calculations, and (5) stationary bed experimental data and calculations. (MOW)

  7. Heat-transfer characteristics of flowing and stationary particle-bed-type fusion-reactor blankets

    International Nuclear Information System (INIS)

    Nietert, R.E.

    1983-02-01

    The following five appendices are included: (1) physical properties of materials, (2) thermal entrance length Nusselt number variations, (3) stationary particle bed temperature variations, (4) falling bed experimental data and calculations, and (5) stationary bed experimental data and calculations

  8. Measurement of flow field in the pebble bed type high temperature gas-cooled reactor

    International Nuclear Information System (INIS)

    Lee, Sa Ya; Lee, Jae Young

    2008-01-01

    In this study, flow field measurement of the Pebble Bed Reactor(PBR) for the High Temperature Gascooled Reactor(HTGR) was performed. Large number of pebbles in the core of PBR provides complicated flow channel. Due to the complicated geometries, numerical analysis has been intensively made rather than experimental observation. However, the justification of computational simulation by the experimental study is crucial to develop solid analysis of design method. In the present study, a wind tunnel installed with pebbles stacked was constructed and equipped with the Particle Image Velocimetry(PIV). We designed the system scaled up to realize the room temperature condition according to the similarity. The PIV observation gave us stagnation points, low speed region so that the suspected high temperature region can be identified. With the further supplementary experimental works, the present system may produce valuable data to justify the Computational Fluid Dynamics(CFD) simulation method

  9. Non-Fickian dispersion in open-channel flow over a porous bed

    Science.gov (United States)

    Bottacin-Busolin, Andrea

    2017-08-01

    Solute transport in rivers has been traditionally represented using one-dimensional models assuming advection and Fickian dispersion along the main flow direction and transient storage in surface and subsurface dead zones. Experimental evidence from several stream tracer studies has shown that the longitudinal scaling of the moments of the breakthrough curves (BTCs) is inconsistent with classic 1-D solute transport models. In this work, simulations of advection and diffusion in a 2-D and 3-D channel flow over a porous bed are presented assuming an exponentially attenuated profile of the transverse mixing coefficient in the porous medium, as suggested by recent experimental and numerical studies. It is shown that the longitudinal transport in the channel is superdiffusive, and the skewness of the concentration distributions can be almost constant over a broad temporal range, with no sign of approaching zero at large times. A sensitivity analysis shows that, at large times, longitudinal dispersion is controlled by the cross-sectional profile of the in-bed transverse mixing coefficient, and by the difference between the average velocity in the channel and in the porous bed. The normalized concentration distributions can be approximated by beta-distributions with time-dependent parameters, and relationships are derived between the scaling of the parameters under power-law approximation and the scaling of the spatial and temporal moments. The results provide new insights into the physical mechanisms that control the anomalous scaling of the moments observed in field tracer studies and opens new possibilities for predictive and inverse modeling of transport processes in rivers and their catchments.

  10. Flow structure through pool-riffle sequences and a conceptual model for their sustainability in gravel-bed rivers

    Science.gov (United States)

    D. Caamano; P. Goodwin; J. M. Buffington

    2010-01-01

    Detailed field measurements and simulations of three-dimensional flow structure were used to develop a conceptual model to explain the sustainability of self-formed pool-riffle sequences in gravel-bed rivers. The analysis was conducted at the Red River Wildlife Management Area in Idaho, USA, and enabled characterization of the flow structure through two consecutive...

  11. Gas-Liquid Two-Phase Flows Through Packed Bed Reactors in Microgravity

    Science.gov (United States)

    Motil, Brian J.; Balakotaiah, Vemuri

    2001-01-01

    The simultaneous flow of gas and liquid through a fixed bed of particles occurs in many unit operations of interest to the designers of space-based as well as terrestrial equipment. Examples include separation columns, gas-liquid reactors, humidification, drying, extraction, and leaching. These operations are critical to a wide variety of industries such as petroleum, pharmaceutical, mining, biological, and chemical. NASA recognizes that similar operations will need to be performed in space and on planetary bodies such as Mars if we are to achieve our goals of human exploration and the development of space. The goal of this research is to understand how to apply our current understanding of two-phase fluid flow through fixed-bed reactors to zero- or partial-gravity environments. Previous experiments by NASA have shown that reactors designed to work on Earth do not necessarily function in a similar manner in space. Two experiments, the Water Processor Assembly and the Volatile Removal Assembly have encountered difficulties in predicting and controlling the distribution of the phases (a crucial element in the operation of this type of reactor) as well as the overall pressure drop.

  12. Experimental study of gas–liquid two-phase flow through packed bed under natural circulation conditions

    International Nuclear Information System (INIS)

    Chen, Shao-Wen; Miwa, Shuichiro; Griffiths, Matt

    2016-01-01

    Dry-out phenomena in packed beds or porous media may cause a significant digression of cooling/reaction performance in heat transfer/chemical reactor systems. One of the phenomena responsible for the dry-out in packed beds is known as the counter-current flow limitation (CCFL). In order to investigate the CCFL phenomena induced by gas–liquid two-phase flow in packed beds inside a pool, a natural circulation packed bed test facility was designed and constructed. A total of 27 experimental conditions covering various packing media sizes (sphere diameters: 3.0, 6.4 and 9.5 mm), packed bed heights (15, 35 and 50 cm) and water level heights (1.0, 1.5 and 2.0 m) were tested to examine the CCFL criteria with adiabatic air–water two-phase flow under natural circulation conditions. Both CCFL and flow reversal phenomena were observed, and the experimental data including instantaneous and time-averaged void fraction, differential pressure and superficial gas–liquid velocities were collected. The CCFL criteria were determined when periodical oscillations of void fraction and differential pressure appear. In addition, the Wallis correlation for CCFL was utilized for data analysis, and the Wallis coefficient, C, was determined experimentally from the packed bed CCFL tests. Compared to the existing data-sets in literature, the higher C values obtained in the present experiment suggest a possibly higher dry-out heat flux for natural circulation debris systems, which may be due to the water supply from both top and bottom surfaces of the packed beds. Considering the effects of bed height and hydraulic diameter of the packing media, a newly developed model for the Wallis coefficient, C, under natural circulation CCFL is presented. The present model can predict the experimental data with an averaged absolute error of ±7.9%. (author)

  13. [Flow model of internal-loop granular sludge bed nitrifying reactor].

    Science.gov (United States)

    Lu, Gang; Zheng, Ping

    2003-11-01

    Internal-loop granular sludge bed nitrifying reactor is a new type of aerobic nitrifying equipment and has shown a good potential for nitrification. To study the flow pattern and construct the flow model, the tracer tests were performed using pulse stimulus-response technique. Based on the experimental results, the flow pattern in the settling section and the circulating section of reactor were analyzed by axial dispersion model and tank-in-series model, respectively. The dispersion number D/uL of 0.00148 in the settling section indicates that its flow pattern is similar to plug flow reactor (PFR), and the series number N of 1.021 in the circulating section indicates that its flow pattern is similar to continuously stirred tank reactor (CSTR). During steady state, the theoretic hydraulic retention time is 360 min, and the actual hydraulic retention time is 341.2 min. The percentage of dead space in the reactor is 5.22%, thereinto the dead space caused by biomass (db ) is 0.75 % and the hydraulic dead space (dh) is 4.47%, which shows that the structural performance of the reactor is excellent. Based on the experiments and analysis, a model of CSTR and PFR in series was constructed. The actual hydraulic retention time distribution of the reactor is in good agreement with the model predictions. Since the relative error between them is 8.56%, the model is accurate to describe the flow pattern. The results have laid a foundation for the kinetic model of the reactor and will be helpful for its design and operation.

  14. Experimental investigation on single-phase pressure losses in nuclear debris beds: Identification of flow regimes and effective diameter

    Energy Technology Data Exchange (ETDEWEB)

    Clavier, R., E-mail: remi.clavier@irsn.fr [Institut de Radioprotection et de Sûreté Nucléaire (IRSN) – PSN-RES/SEREX/LE2M, Cadarache bât. 327, 13115 St Paul-lez-Durance (France); Chikhi, N., E-mail: nourdine.chikhi@irsn.fr [Institut de Radioprotection et de Sûreté Nucléaire (IRSN) – PSN-RES/SEREX/LE2M, Cadarache bât. 327, 13115 St Paul-lez-Durance (France); Fichot, F. [Institut de Radioprotection et de Sûreté Nucléaire (IRSN) – PSN-RES/SAG/LEPC, Cadarache bât. 700, 13115 St Paul-lez-Durance (France); Quintard, M. [Université de Toulouse – INPT – UPS – Institut de Mécanique des Fluides de Toulouse (IMFT), Allée Camille Soula, F-31400 Toulouse (France); CNRS – IMFT, F-31400 Toulouse (France)

    2015-10-15

    Highlights: • Single-phase pressure drops versus flow rates in particle beds are measured. • Conditions are representative of the reflooding of a nuclear fuel debris bed. • Darcy, weak inertial, strong inertial and weak turbulent regimes are observed. • A Darcy–Forchheimer law is found to be a good approximation in this domain. • A predictive correlation is derived from new experimental data. - Abstract: During a severe nuclear power plant accident, the degradation of the reactor core can lead to the formation of debris beds. The main accident management procedure consists in injecting water inside the reactor vessel. Nevertheless, large uncertainties remain regarding the coolability of such debris beds. Motivated by the reduction of these uncertainties, experiments have been conducted on the CALIDE facility in order to investigate single-phase pressure losses in representative debris beds. In this paper, these results are presented and analyzed in order to identify a simple single-phase flow pressure loss correlation for debris-bed-like particle beds in reflooding conditions, which cover Darcean to Weakly Turbulent flow regimes. The first part of this work is dedicated to study macro-scale pressure losses generated by debris-bed-like particle beds, i.e., high sphericity (>80%) particle beds with relatively small size dispersion (from 1 mm to 10 mm). A Darcy–Forchheimer law, involving the sum of a linear term and a quadratic deviation, with respect to filtration velocity, has been found to be relevant to describe this behavior in Darcy, Strong Inertial and Weak Turbulent regimes. It has also been observed that, in a restricted domain (Re = 15 to Re = 30) between Darcy and Weak Inertial regimes, deviation is better described by a cubic term, which corresponds to the so-called Weak Inertial regime. The second part of this work aims at identifying expressions for coefficients of linear and quadratic terms in Darcy–Forchheimer law, in order to obtain a

  15. Flow instability tests for a particle bed reactor nuclear thermal rocket fuel element

    Science.gov (United States)

    Lawrence, Timothy J.

    1993-05-01

    Recent analyses have focused on the flow stability characteristics of a particle bed reactor (PBR). These laminar flow instabilities may exist in reactors with parallel paths and are caused by the heating of the gas at low Reynolds numbers. This phenomena can be described as follows: several parallel channels are connected at the plenum regions and are stabilized by some inlet temperature and pressure; a perturbation in one channel causes the temperature to rise and increases the gas viscosity and reduces the gas density; the pressure drop is fixed by the plenum regions, therefore, the mass flow rate in the channel would decrease; the decrease in flow reduces the ability to remove the energy added and the temperature increases; and finally, this process could continue until the fuel element fails. Several analyses based on different methods have derived similar curves to show that these instabilities may exist at low Reynolds numbers and high phi's ((Tfinal Tinitial)/Tinitial). These analyses need to be experimentally verified.

  16. Hydrogenotrophic denitrification in a packed bed reactor: effects of hydrogen-to-water flow rate ratio.

    Science.gov (United States)

    Lee, J W; Lee, K H; Park, K Y; Maeng, S K

    2010-06-01

    Hydrogen dissolution and hydrogenotrophic denitrification performance were investigated in a lab-scale packed bed reactor (PBR) by varying the hydrogen flow rate and hydraulic retention time (HRT). The denitrification performance was enhanced by increasing the hydrogen flow rate and HRT as a result of high dissolved hydrogen concentration (0.39mg/L) and utilization efficiencies (79%). In this study, the hydrogen-to-water flow rate ratio (Q(g)/Q(w)) was found to be a new operating factor representing the two parameters of hydrogen flow rate and HRT. Hydrogen dissolution and denitrification efficiency were nonlinearly and linearly correlated with the Q(g)/Q(w), respectively. Based on its excellent linear correlation with denitrification efficiency, Q(g)/Q(w) should be greater than 2.3 to meet the WHO's guideline of nitrate nitrogen for drinking water. This study demonstrates that Q(g)/Q(w) is a simple and robust factor to optimize hydrogen-sparged bioreactors for hydrogenotrophic denitrification. Copyright 2010 Elsevier Ltd. All rights reserved.

  17. An Experimental and Computational Study of Multiphase Flow Behaviour in Circulating Fluidized Beds

    Energy Technology Data Exchange (ETDEWEB)

    Mathiesen, Vidar

    1997-12-31

    Gas/solid flows have been studied extensively, mainly because they are important in nuclear, chemical and petroleum industries. This thesis describes an experiment done at two different circulating fluidized bed systems. Laser Doppler anemometry (LDA) and phase Doppler anemometry (PDA) were used to measure mean and fluctuating velocity, diameter and solids concentration. A typical core-annulus flow was obtained in both cases. The measurements show a relative mean velocity as well as a relative fluctuating velocity between different particle sizes. An axial segregation by size and its variation with the superficial gas velocity are demonstrated. Significant radial segregation is found in both risers. A three-dimensional Computational Fluid Dynamics model was developed based on Eulerian description of the phases where the kinetic theory of granular flow is the basis of the turbulence modelling in the solid phases. There are one gas phase and any number of solid phases. Simulations of flow behaviour in two- and three-dimensions agree well with experiments and the model is able to handle axial segregation by size for different superficial gas velocities and particle size distributions. 107 refs., 79 figs., 6 tabs.

  18. Dynamic Flow Behavior Measurements in Gas-Solid Fluidized Beds Using Different Non-Intrusive Techniques and Polyethylene Powder

    Science.gov (United States)

    Wu, Bangyou; Yu, Guang; Bellehumeur, Celine; Kantzas, Apostolos

    2007-06-01

    Pressure fluctuations and X-ray computed tomography (CT) measurements were utilized to characterize the flow behavior of gas-solid fluidized beds using polyethylene particles in three Plexiglas columns with diameters of 10cm, 20cm, and 30cm. Air was used as the gas phase. Gas-solids flow dynamic under ambient conditions was characterized from statistical analysis of pressure fluctuation data and CT images. The time-averaged voidage distribution, bubble phase area fraction, bubble diameter and bubble number distribution varying with the bed heights were extracted from all the three columns. Bed scales had significant effect on the hydrodynamics. Scale up effects on the gas-solids two-phase flow behavior were discussed.

  19. Non-local rheology of stony debris flow propagating over a cohesionless sediment bed

    Science.gov (United States)

    Lanzoni, Stefano; Gregoretti, Carlo

    2016-04-01

    normal to the flow, with particular attention to the role played by frictional stresses near to the movable bed over which the debris flow propagates.

  20. Numerical simulations and correlations on the coal -conveying gas flow in pipe for fluidized -bed coal gasification facility

    International Nuclear Information System (INIS)

    Lee, Chan; Lee, Jin Wook; Kwon, Tae Wan; Kim, Gyoo Tae

    2014-01-01

    CFD modeling and simulation are made on the key flow elements, vertical, horizontal pipes and elbow pipes , used in the pneumatic coal -transport system of fluidized -bed gasification test facility. The coal- gas flow inside the flow elements are modeled by combining Reynolds -stress Averaged Navier- Stokes equations Solver (RANS), k- ε turbulence model and Discrete Phase Model (DPM) in the ANSYS Fluent code. Using the developed coal -gas flow analysis model, computations are carried out to investigate the gas flow path, the coal particle behavior and the pressure loss characteristics in flow element at various coal/ gas loading ratio and coal mass flux. The present prediction results show the coal -gas flow behavior of each flow element is changed from dilute -flow to dense -flow pattern at a specific coal/gas loading ratio where pressure loss is abruptly increased. From the numerical results, the present study also provides the limiting coal/gas loading conditions to secure stable coal feeding and the correlations for pressure losses in horizontal, vertical and elbow pipes, which can be suitable for the design guidelines of actual fluidized -bed coal gasification. Key words : Pneumatic Coal -Transport; Coal -Gas Flow, Dense Phase Flow; Dilute Phase Flow; Pressure Loss; Coal/Gas Loading Ratio; Correlation

  1. DEVELOPMENT OF AN EXPERIMENTAL TEST BED DESIGNATED FOR MODEL STUDIES OF AERODYNAMICS OF PREMISES USING METHOD OF DIGITAL FLOW VISUALIZATION

    Directory of Open Access Journals (Sweden)

    Varapaev Vladimir Nikolaevich

    2012-12-01

    Full Text Available In the article, the authors present their findings generated at the laboratory of aerodynamic and aero-acoustic testing of structural units of MGSU. The authors provide information about the principle of operation and a brief description of the experimental test bed designated for the physical research of patterns of air flows arising inside building premises of various geometric shapes. The authors also demonstrate the basic parameters of the test bed, the principle of operation of its recording devices and some of its characteristics. The test bed is designated for the identification of characteristics of three-dimensional flows of models under research and for the verification of results of numerical studies. The measurement bed has advanced measurement and registration units. The management principle is based on the method of digital flow visualization, PIV method and Doppler flow meter implemented in the LDA anemometer. The test stand generates two or three component vector fields of turbulent gas flow velocities. It may be applicable to the study of liquids in case of research of hydraulics-related problems. Some results of the flow study are provided in the article, as well.

  2. Thresholds of flow-induced bed disturbances and their effects on stream metabolism in an agricultural river

    Science.gov (United States)

    O'Connor, Ben L.; Harvey, Judson W.; McPhillips, Lauren E.

    2012-01-01

    Storm-driven flow pulses in rivers destroy and restructure sediment habitats that affect stream metabolism. This study examined thresholds of bed disturbances that affected patch- and reach-scale sediment conditions and metabolism rates. A 4 year record of discharge and diel changes in dissolved oxygen concentrations (ΔDO) was analyzed for disturbances and recovery periods of the ΔDO signal. Disturbances to the ΔDO signal were associated with flow pulses, and the recovery times for the ΔDO signal were found to be in two categories: less than 5 days (30% of the disturbances) or greater than 15 days (70% of the disturbances). A field study was performed during the fall of 2007, which included a storm event that increased discharge from 3.1 to 6.9 m3/s over a 7 h period. During stable flow conditions before the storm, variability in patch-scale stream metabolism values were associated with sediment texture classes with values ranging from −16.4 to 2.3 g O22/d (negative sign indicates net respiration) that bounded the reach-averaged rate of −5.6 g O22/d. Hydraulic modeling of bed shear stresses demonstrated a storm-induced flow pulse mobilized approximately 25% of the bed and reach-scale metabolism rates shifted from −5 to −40 g O22/d. These results suggest that storm-induced bed disturbances led to threshold behavior with respect to stream metabolism. Small flow pulses resulted in partial-bed mobilization that disrupted stream metabolism by increased turbidity with short recovery times. Large flow pulses resulted in full-bed mobilization that disrupted stream metabolism by destroying periphyton habitats with long recovery times.

  3. Robust biological nitrogen removal by creating multiple tides in a single bed tidal flow constructed wetland.

    Science.gov (United States)

    Hu, Yuansheng; Zhao, Yaqian; Rymszewicz, Anna

    2014-02-01

    Achieving effective total nitrogen (TN) removal is one of the major challenges faced by constructed wetlands (CWs). To address this issue, multiple "tides" were proposed in a single stage tidal flow constructed wetland (TFCW). With this adoption, exceptional TN removal (85% on average) was achieved under a high nitrogen loading rate (NLR) of around 28 g Nm(-2)day(-1), which makes the proposed system an adequate option to provide advanced wastewater treatment for peri-urban communities and rural area. It was revealed that the multiple "tides" not only promoted TN removal performance, but also brought more flexibility to TFCWs. Adsorption of NH4(+)-N onto the wetland medium (during contact period) and regeneration of the adsorption capacity via nitrification (during bed resting) were validated as the key processes for NH4(+)-N conversion in TFCWs. Moreover, simultaneous nitrification denitrification (SND) was found to be significant during the bed resting period. These findings will provide a new foundation for the design and modeling of nitrogen conversion and oxygen transfer in TFCWs. © 2013.

  4. Investigation of flow regime in debris bed formation behavior with nonspherical particles

    Directory of Open Access Journals (Sweden)

    Songbai Cheng

    2018-02-01

    Full Text Available It is important to clarify the characteristics of flow regimes underlying the debris bed formation behavior that might be encountered in core disruptive accidents of sodium-cooled fast reactors. Although in our previous publications, by applying dimensional analysis technique, an empirical model, with its reasonability confirmed over a variety of parametric conditions, has been successfully developed to predict the regime transition and final bed geometry formed, so far this model is restricted to predictions of debris mixtures composed of spherical particles. Focusing on this aspect, in this study a new series of experiments using nonspherical particles have been conducted. Based on the knowledge and data obtained, an extension scheme is suggested with the purpose of extending the base model to cover the particle-shape influence. Through detailed analyses and given our current range of experimental conditions, it is found that, by coupling the base model with this scheme, respectable agreement between experiments and model predictions for the regime transition can be achieved for both spherical and nonspherical particles. Knowledge and evidence from our work might be utilized for the future improvement of design of an in-vessel core catcher as well as the development and verification of sodium-cooled fast reactor severe accident analysis codes in China.

  5. Cold flow study of liquid cooled pebble bed reactor (LC-PBR) through radioisotope techniques

    International Nuclear Information System (INIS)

    Verma, Rupesh; Upadhyay, Rajesh K.; Pant, H.J.

    2017-01-01

    As the world's demand for energy continues to increase burning of coal, oil and natural gases continue to increase which will eventually cause build-up in emission of greenhouse gasses. To overcome this challenge worldwide effort is in progress to develop an economical, more efficient and safer nuclear power. Higher thermal efficiency and enhances safety feature of Generation IV liquid cooled pebble bed reactor (LC-PBR) makes it viable option to replace existing nuclear reactor. However, this reactor is still in research stage and need detailed study before commercialization. In current work, hydrodynamics of LC-PBR is studied by using radioisotope based techniques, radioactive particle tracking and gamma-ray densitometry. Pebble flow profile and distribution are measured for different operating conditions. Optimal operating parameters are identified for operating LC-PBR based on hydrodynamics. (author)

  6. Contact detection acceleration in pebble flow simulation for pebble bed reactor systems

    Energy Technology Data Exchange (ETDEWEB)

    Li, Y.; Ji, W. [Department of Mechanical, Aerospace, and Nuclear Engineering Rensselaer, Polytechnic Institute, 110 8th street, Troy, NY 12180 (United States)

    2013-07-01

    Pebble flow simulation plays an important role in the steady state and transient analysis of thermal-hydraulics and neutronics for Pebble Bed Reactors (PBR). The Discrete Element Method (DEM) and the modified Molecular Dynamics (MD) method are widely used to simulate the pebble motion to obtain the distribution of pebble concentration, velocity, and maximum contact stress. Although DEM and MD present high accuracy in the pebble flow simulation, they are quite computationally expensive due to the large quantity of pebbles to be simulated in a typical PBR and the ubiquitous contacts and collisions between neighboring pebbles that need to be detected frequently in the simulation, which greatly restricted their applicability for large scale PBR designs such as PBMR400. Since the contact detection accounts for more than 60% of the overall CPU time in the pebble flow simulation, the acceleration of the contact detection can greatly enhance the overall efficiency. In the present work, based on the design features of PBRs, two contact detection algorithms, the basic cell search algorithm and the bounding box search algorithm are investigated and applied to pebble contact detection. The influence from the PBR system size, core geometry and the searching cell size on the contact detection efficiency is presented. Our results suggest that for present PBR applications, the bounding box algorithm is less sensitive to the aforementioned effects and has superior performance in pebble contact detection compared with basic cell search algorithm. (authors)

  7. Flow pattern analysis of a full-scale expanded granular sludge bed-type reactor under different organic loading rates.

    Science.gov (United States)

    Zheng, M X; Wang, K J; Zuo, J E; Yan, Z; Fang, H; Yu, J W

    2012-03-01

    The hydraulic characteristics of a lab-scale and a full-scale (275 m(3)) expanded granular sludge bed (EGSB)-type reactor under different organic loading rates varying from 10 kg COD m(-3)d(-1) to 45 kg COD m(-3)d(-1) were investigated. A modified combined model composed of two completely mixing regions and a plug flow region was sufficient for simulating the flow pattern of a full-scale EGSB-type reactor. Moreover, the outputs fitted the measured tracer distribution results well. The simplified model structure was in very good agreement with the physical structure of a full-scale EGSB-type reactor. The upflow (liquid+gas) velocity, high concentration of granular sludge, and gas hold-up effect may contribute to the generation of dead spaces (maximum of 19.5%). The bed expansion characteristics indicated that the sludge bed of the EGSB-type reactor performed as a suspended bed, in which the bed expansion was controlled between 20% and 30%, rather than the usually considered expanded bed. Copyright © 2011 Elsevier Ltd. All rights reserved.

  8. Hydrodynamic characteristics of a two-phase gas-liquid flow upward through a fixed bed of spherical particles

    Directory of Open Access Journals (Sweden)

    VELIZAR D. STANKOVIC

    2001-01-01

    Full Text Available The influence of an electrochemically generated gas phase on the hydrodynamic characteristics of a three-phase system has been examined. The two-phase fluid, (gas-liquid, in which the liquid phase is the continuous one, flows through a packed bed with glass spheres. The influence of the liquid velocity was examined, as well as the gas velocity and particle diameter on the pressure drop through the fixed bed. It was found that with increasing liquid velocity (wl = 0.0162–0.03 m/s, the relative pressure drop decreases through the fixed bed. With increasing current density, the pressure drop increases, since greater gas quantities stay behind in the fixed bed. Besides, it was found that with decreasing diameter of the glass particles, the relative pressure drop also decreases. The relationship betweeen the experimentally obtained friction factor and the Reynolds number was established.

  9. Bed load size distribution and flow conditions in a high mountain catchment of Central Pyrenees

    Directory of Open Access Journals (Sweden)

    Martínez-Castroviejo, Ricardo

    1990-06-01

    Full Text Available The bed load size distribution caused by different types of flow are compared in a high mountain catchment located in the upper Gallego river basin (Central Spanish’ Pyrenees. Three kinds of hydrologic events could be defined: those triggered by heavy autumn rainfalls, those originated by isolated summer rainstorms and those promoted by snowmelting. Each one is characterized by a peculiar bed load size distribution. Thus, it could be demonstrated that the coarser fractions, above 30 mm in diameter, are up to six times more abundant, in percentage of total weight, in transports caused by heavy rainfalls than in the material collected after snowmelt flows. In its turn, bed load mobilized by snowmelt flows is mainly composed by medium and fine gravel, from 2 to 8 mm. These may amount up to 60 % of total weight of bed load. The reasons for these so different size distributions are discussed.

    [es] En una cuenca de alta montaña localizada en el alto valle del río Gallego (Pirineo central se comparan las distribuciones por tamaños de los acarreos movilizados por diferentes tipos de caudal. Tres tipos de eventos hidrológicos han podido ser caracterizados: los ocasionados por intensas lluvias de otoño, los originados por tormentas estivales aisladas y los producidos por la fusión de la nieve acumulada durante el invierno. Se concluye que cada uno de ellos lleva asociada una distribución por tamaños típica de la carga de fondo. Así, se ha comprobado que las fracciones más gruesas consideradas -superiores a los 30 mm de diámetro- son hasta seis veces más abundantes -en porcentaje sobre el peso total- en las exportaciones causadas por lluvias de gran intensidad que en las generadas por caudales de fusión. A su vez, las descargas ocasionadas por la fusión arrastran principalmente gravas de calibre medio y fino -entre 2y8 mm- que llegan a suponer el 60 % en peso del volumen movilizado. Este artículo discute las razones que provocan

  10. An experimental study on coolability of a particulate bed with radial stratification or triangular shape

    International Nuclear Information System (INIS)

    Thakre, Sachin; Li, Liangxing; Ma, Weimin

    2014-01-01

    Highlights: • Dryout heat flux of a particulate bed with radial stratification is obtained. • It was found to be dominated by hydrodynamics in the bigger size of particle layer. • Coolability of a particulate bed with triangular shape is investigated. • The coolability is improved in the triangular bed due to lateral ingression of coolant. • Coolability of both beds is enhanced by a downcomer. - Abstract: This paper deals with the results of an experimental study on the coolability of particulate beds with radial stratification and triangular shape, respectively. The study is intended to get an idea on how the coolability is affected by the different features of a debris bed formed in a severe accident of light water reactors. The experiments were performed on the POMECO-HT facility which was constructed to investigate two-phase flow and heat transfer in particulate beds under either top-flooding or bottom-fed condition. A downcomer is designed to enable investigation of the effectiveness of natural circulation driven coolability. Two homogenous beds were also employed in the present study to compare their dryout power densities with those of the radially stratified bed and the triangular bed. The results show that the dryout heat fluxes of the homogeneous beds at top-flooding condition can be predicted by the Reed model. For the radially stratified bed, the dryout heat flux is dominated by two-phase flow in the columns packed with larger particles, and the dryout occurred initially near the boundary between the middle column and a side column. Given the same volume of particles under top-flooding condition, the dryout power density of the triangular bed is about 69% higher than that of the homogenous bed. The coolability of all the beds is enhanced by bottom-fed coolant driven by either forced injection or downcomer-induced natural circulation

  11. Experimental analysis of the influence of air-flow rate on wheat straw combustion in a fixed bed

    Directory of Open Access Journals (Sweden)

    Čepić Zoran M.

    2017-01-01

    Full Text Available Biomass in the form of crop residues represents a significant energy source in regions whose development is based on agricultural production. Among many possibilities of utilizing biomass for energy generation, combustion is the most common. With the aim of improving and optimizing the combustion process of crop residues, an experimental rig for straw combustion in a fixed bed was constructed. This paper gives a brief review of working characteristics of the experimental rig, as well as the results for three different measuring regimes, with the purpose to investigate the effect of air-flow rate on the wheat straw combustion in a fixed bed. For all three regimes analysed in this paper bulk density of the bed was the same, 60 kg/m3, combustion air was without preheating and air-flow rates were: 1152, 1872, and 2124 kg/m2h. The effect of air-flow rate on the ignition rate, burning rate, temperature profile of the bed and flue gas composition were analysed. It was concluded that in the regime with the lowest air-flow rate progress of combustion had two clearly conspicuous stages: the ignition propagation stage and the char and unburned material oxidation stage. At the highest air-flow rate the entire combustion occurred mostly in a single stage, due to increased air supply oxidized the char, remaining above the ignition front, simultaneously with the reactions of volatiles. Despite that, the optimal combustion process, the highest value of ignition rate, burning rate, and bed temperature was achieved with air-flow rate of 1872 kg/m2h.

  12. Temperature distribution on the MEA surface of a PEMFC with serpentine channel flow bed

    Science.gov (United States)

    Wang, Maohai; Guo, Hang; Ma, Chongfang

    Knowledge of the temperature distribution on the membrane electrode assembly (MEA) surface and heat transfer processes inside a proton exchange membrane fuel cell (PEMFC) is helpful to improvement of cell reliability, durability and performance. The temperature fields on the surface of MEA fixed inside a proton exchange membrane fuel cell with a serpentine channel flow bed were measured by infrared imaging technology under non-humidification conditions. The temperature distributions over the MEA surface under whole channel region were achieved. The experimental results show that the downstream temperatures are higher than the upstream. The hot region on the MEA surface is easy to locate from the infrared temperature image. The mean temperature on the MEA surface and the cell temperature both increase with the current density. Higher current density makes the non-uniformity of temperature distribution on the MEA surface worse. The loading time significantly affects the temperature distribution. Compared with the electrical performance of the cell, the MEA's temperatures need much more time to reach stable. The results indicate that isothermal assumption is not appropriate for a modeling of PEMFCs, and monitoring the temperature of external surface of the flow field plate or end plate cannot supply accurate reference to control the temperatures on MEA surface.

  13. Bed Evolution under Rapidly Varying Flows by a New Method for Wave Speed Estimation

    Directory of Open Access Journals (Sweden)

    Khawar Rehman

    2016-05-01

    Full Text Available This paper proposes a sediment-transport model based on coupled Saint-Venant and Exner equations. A finite volume method of Godunov type with predictor-corrector steps is used to solve a set of coupled equations. An efficient combination of approximate Riemann solvers is proposed to compute fluxes associated with sediment-laden flow. In addition, a new method is proposed for computing the water depth and velocity values along the shear wave. This method ensures smooth solutions, even for flows with high discontinuities, and on domains with highly distorted grids. The numerical model is tested for channel aggradation on a sloping bottom, dam-break cases at flume-scale and reach-scale with flat bottom configurations and varying downstream water depths. The proposed model is tested for predicting the position of hydraulic jump, wave front propagation, and for predicting magnitude of bed erosion. The comparison between results based on the proposed scheme and analytical, experimental, and published numerical results shows good agreement. Sensitivity analysis shows that the model is computationally efficient and virtually independent of mesh refinement.

  14. Dispersed plug flow model for upflow anaerobic sludge bed reactors with focus on granular sludge dynamics.

    Science.gov (United States)

    Kalyuzhnyi, Sergey V; Fedorovich, Vyacheslav V; Lens, Piet

    2006-03-01

    A new approach to model upflow anaerobic sludge bed (UASB)-reactors, referred to as a one-dimensional dispersed plug flow model, was developed. This model focusses on the granular sludge dynamics along the reactor height, based on the balance between dispersion, sedimentation and convection using one-dimensional (with regard to reactor height) equations. A universal description of both the fluid hydrodynamics and granular sludge dynamics was elaborated by applying known physical laws and empirical relations derived from experimental observations. In addition, the developed model includes: (1) multiple-reaction stoichiometry, (2) microbial growth kinetics, (3) equilibrium chemistry in the liquid phase, (4) major solid-liquid-gas interactions, and (5) material balances for dissolved and solid components along the reactor height. The integrated model has been validated with a set of experimental data on the start-up, operation performance, sludge dynamics, and solute intermediate concentration profiles of a UASB reactor treating cheese whey [Yan et al. (1989) Biol Wastes 27:289-305; Yan et al. (1993) Biotechnol Bioeng 41:700-706]. A sensitivity analysis of the model, performed with regard to the seed sludge characteristics and the key model parameters, showed that the output of the dispersed plug flow model was most influenced by the sludge settleability characteristics and the growth properties (especially mu(m)) of both protein-degrading bacteria and acetotrophic methanogens.

  15. A SPH elastic-viscoplastic model for granular flows and bed-load transport

    Science.gov (United States)

    Ghaïtanellis, Alex; Violeau, Damien; Ferrand, Martin; Abderrezzak, Kamal El Kadi; Leroy, Agnès; Joly, Antoine

    2018-01-01

    An elastic-viscoplastic model (Ulrich, 2013) is combined to a multi-phase SPH formulation (Hu and Adams, 2006; Ghaitanellis et al., 2015) to model granular flows and non-cohesive sediment transport. The soil is treated as a continuum exhibiting a viscoplastic behaviour. Thus, below a critical shear stress (i.e. the yield stress), the soil is assumed to behave as an isotropic linear-elastic solid. When the yield stress is exceeded, the soil flows and behaves as a shear-thinning fluid. A liquid-solid transition threshold based on the granular material properties is proposed, so as to make the model free of numerical parameter. The yield stress is obtained from Drucker-Prager criterion that requires an accurate computation of the effective stress in the soil. A novel method is proposed to compute the effective stress in SPH, solving a Laplace equation. The model is applied to a two-dimensional soil collapse (Bui et al., 2008) and a dam break over mobile beds (Spinewine and Zech, 2007). Results are compared with experimental data and a good agreement is obtained.

  16. Bypass flow and its role in leaching of raised beds under different land use types on an acid sulphate soil.

    NARCIS (Netherlands)

    Minh, L.Q.; Tuong, T.P.; Booltink, H.W.G.; Mensvoort, van M.E.F.; Bouma, J.

    1997-01-01

    A better understanding of leaching processes in raised beds is useful in assessing management options for acid sulphate soils. Field and laboratory studies were carried out to quantify the effects of soil physical properties and bypass flow on leaching processes of new, 1-year-old and 2-year-old

  17. Wave-frequency flows within a near-bed vegetation canopy

    Science.gov (United States)

    Henderson, Stephen M.; Norris, Benjamin K.; Mullarney, Julia C.; Bryan, Karin R.

    2017-09-01

    We study water flows and wave dissipation within near-bed pneumatophore canopies at the wave-exposed fringe of a mangrove forest on Cù Lao Dung Island, in the Mekong Delta. To evaluate canopy drag, the three-dimensional geometry of pneumatophore stems growing upward from the buried lateral roots of Sonneratia caseolaris mangroves was reconstructed from photogrammetric surveys. In cases where hydrodynamic measurements were obtained, up to 84 stems per square meter were observed, with stem heights basal diameters 0.01-0.02 m. The parameter a = (frontal area of pneumatophores blocking the flow)/(canopy volume) ranged from zero to 1.8 m-1. Within-canopy water velocity displayed a phase lead and slight attenuation relative to above-canopy flows. The phase lead was frequency-dependent, ranging from 0 to 30 degrees at the frequencies of energetic waves (> 0.1 Hz), and up to 90 degrees at lower frequencies. A model is developed for wave-induced flows within the vertically variable canopy. Scaling suggests that acceleration-induced forces and vertical mixing were negligible at wave frequencies. Consistent with theory, drag-induced vertical variability in velocity scaled with Λ =Tw / (2 πTf) , where Tw = wave period, Tf = 2 / (CD a | u |) is the frictional time scale, CD ≈ 2 is the drag coefficient, and | u | is a typical flow speed. For fixed wave conditions (| u | and Tw), theory predicts increasing dissipation with increasing vegetation density (i.e. increasing a), until a maximum is reached for order-one Λ. For larger Λ, within-canopy flow is so inhibited by drag that further increases in a reduce within-canopy dissipation. For observed cases, Λ ⩽ 0.38 at energetic wave frequencies, so wave dissipation near the forest edge is expected to increase with increasing pneumatophore canopy density. However, under different wave conditions, the most dense canopies may occasionally approach the dissipation maximum (Λ ≈ 1). Predicted dissipation by the pneumatophore

  18. Concentration profiles in the wake of a sphere buried in a granular bed through which fluid flows

    International Nuclear Information System (INIS)

    Guedes de Carvalho, J.R.F.; Delgado, J.M.P.Q.; Alves, M.A.

    2005-01-01

    The concentration distribution in the wake of a soluble sphere immersed in a granular bed of inerts has been obtained numerically, for transport by both advection and diffusion/dispersion. Fluid flow in the granular bed around the sphere was assumed to follow Darcy's law and, at each point, dispersion of solute was considered in both the cross-stream and stream-wise directions. The elliptic PDE equation, resulting from a differential material balance on the solute, has been solved numerically over a wide range of values of the relevant parameters. (authors)

  19. Concentration profiles in the wake of a sphere buried in a granular bed through which fluid flows

    Energy Technology Data Exchange (ETDEWEB)

    Guedes de Carvalho, J.R.F.; Delgado, J.M.P.Q.; Alves, M.A. [Porto Univ., Dpet. de Engenharia Quimica, Faculdade de Engenharia (Portugal)

    2005-07-01

    The concentration distribution in the wake of a soluble sphere immersed in a granular bed of inerts has been obtained numerically, for transport by both advection and diffusion/dispersion. Fluid flow in the granular bed around the sphere was assumed to follow Darcy's law and, at each point, dispersion of solute was considered in both the cross-stream and stream-wise directions. The elliptic PDE equation, resulting from a differential material balance on the solute, has been solved numerically over a wide range of values of the relevant parameters. (authors)

  20. Influence of liquid and gas flow rates on sulfuric acid mist removal from air by packed bed tower

    Directory of Open Access Journals (Sweden)

    Jafari Mohammad Javad

    2012-12-01

    Full Text Available Abstract The possible emission of sulfuric acid mists from a laboratory scale, counter-current packed bed tower operated with a caustic scrubbing solution was studied. Acid mists were applied through a local exhaust hood. The emissions from the packed bed tower were monitored in three different categories of gas flow rate as well as three liquid flow rates, while other influencing parameters were kept almost constant. Air sampling and sulfuric acid measurement were carried out iso-kinetically using USEPA method 8. The acid mists were measured by the barium-thorin titration method. According to the results when the gas flow rate increased from 10 L/s to 30 L/s, the average removal efficiency increased significantly (p 3, respectively. L/G of 2–3 was recommended for designing purposes of a packed tower for sulfuric acid mists and vapors removal from contaminated air stream.

  1. Influence of liquid and gas flow rates on sulfuric acid mist removal from air by packed bed tower

    Science.gov (United States)

    2012-01-01

    The possible emission of sulfuric acid mists from a laboratory scale, counter-current packed bed tower operated with a caustic scrubbing solution was studied. Acid mists were applied through a local exhaust hood. The emissions from the packed bed tower were monitored in three different categories of gas flow rate as well as three liquid flow rates, while other influencing parameters were kept almost constant. Air sampling and sulfuric acid measurement were carried out iso-kinetically using USEPA method 8. The acid mists were measured by the barium-thorin titration method. According to the results when the gas flow rate increased from 10 L/s to 30 L/s, the average removal efficiency increased significantly (p 3, respectively. L/G of 2–3 was recommended for designing purposes of a packed tower for sulfuric acid mists and vapors removal from contaminated air stream. PMID:23369487

  2. Bed morphology, flow structure, and sediment transport at the outlet of Lake Huron and in the upper St. Clair River

    Science.gov (United States)

    Czuba, J.A.; Best, J.L.; Oberg, K.A.; Parsons, D.R.; Jackson, P.R.; Garcia, M.H.; Ashmore, P.

    2011-01-01

    An integrated multibeam echo sounder and acoustic Doppler current profiler field survey was conducted in July 2008 to investigate the morphodynamics of the St. Clair River at the outlet of Lake Huron. The principal morphological features of the upper St. Clair River included flow-transverse bedforms that appear weakly mobile, erosive bedforms in cohesive muds, thin non-cohesive veneers of weakly mobile sediment that cover an underlying cohesive (till or glacio-lacustrine) surface, and vegetation that covers the bed. The flow was characterized by acceleration as the banks constrict from Lake Huron into the St. Clair River, an approximately 1500-m long region of flow separation downstream from the Blue Water Bridge, and secondary flow connected to: i) channel curvature; ii) forcing of the flow by local bed topography, and iii) flow wakes in the lee side of ship wrecks. Nearshore, sand-sized, sediment from Lake Huron was capable of being transported into, and principally along, the banks of the upper St. Clair River by the measured flow. A comparison of bathymetric surveys conducted in 2007 and 2008 identifies that the gravel bed does undergo slow downstream movement, but that this movement does not appear to be generated by the mean flow, and could possibly be caused by ship-propeller-induced turbulence. The study results suggest that the measured mean flow and dredging within the channel have not produced major scour of the upper St. Clair River and that the recent fall in the level of Lake Huron is unlikely to have been caused by these mechanisms. ?? 2011.

  3. Reeds diesel engine troubleshooting handbook

    CERN Document Server

    Pickthall, Barry

    2013-01-01

    Most diesel engines will develop a problem at some point in their lives, but armed with the right knowledge a skipper needn't worry. The Reeds Diesel Engine Troubleshooting Handbook is a compact, pocket-sized guide to finding solutions to all of the most common engine problems, and many of the less common ones too. The perfect format for quick reference on board, this book will help skippers fix troublesome engines themselves, avoiding costly engineer fees if the problem is simple to sort out, or enabling an emergency patch-up for a more serious problem until they can get back to port. Each to

  4. A shallow-flow model for the propagation of tsunamis over complex geometries and mobile beds

    Directory of Open Access Journals (Sweden)

    D. A. S. Conde

    2013-10-01

    Full Text Available A distinguishable feature of overland tsunami propagation is the incorporation of solids within the flow column, either sediment from the natural environment or remains from built infrastructure. This article describes a 2DH (two-dimensional horizontal mathematical model particularly suited for tsunami propagation over complex and dynamic geometries, such as river and estuarine mobile beds. The discretization scheme is based on a finite-volume method using a flux-splitting technique featuring a reviewed Roe–Riemann solver, with appropriate source-term formulations to ensure full conservativeness. The model is validated with laboratory data and paleo-tsunami evidence. As a forecasting application, it is applied to a tsunami scenario in the Tagus estuary, an effort justified by the numerous catastrophic tsunamis that are known to have struck this location over the past two millennia. The obtained results show that, despite the significant differences in Lisbon's layout and morphology, a 1755-like tsunami would still inflict a devastating impact on this major city.

  5. Numerical Simulation of the Gas-Solid Flow by DEM-CFD Approach with Application to a Spouted Bed

    Directory of Open Access Journals (Sweden)

    Jinhe FAN

    2014-02-01

    Full Text Available The paper presents a computational study of the gas-solid flow in a three- dimensional spouted bed by a combined approach of discrete element method and computational fluid dynamics (DEM-CFD.The coupling between the discrete particle and continuum gas was achieved by applying the principle of Newton’s third law of motion. As a result, it is found that the motion of particles was forming a distinct circulation between center zone and boundary zone of the 3D spouted bed in macro, and there was a stagnant zone near the bottom of the bed in which the particle velocity is almost zero near the wall, they do not move anywhere. Pressure drop will be affected by wind speed and particle density. With enhancing of wind velocity, pressure drop appears an increasing trend until it is up to a certain value, and then the curve will have a certain degree of back and keep in an extension; Adding particle density, pressure drop and its swing is increased markedly. The results of this study provide important information in the spouted bed and may be helpful for better application and modification of this type of spouted bed to the industrial process.

  6. Influence of decelerating flow on incipient motion of a gravel-bed ...

    Indian Academy of Sciences (India)

    2016-08-26

    Aug 26, 2016 ... From the observation of eleven fixed-bed and nine mobile-bed velocity profiles, it is revealed that the parabolic law method (PLM) and the Reynolds stress method are comparable for estimation of shear velocity in general. Also, the results show that the shear stress distribution adopts a convex form over ...

  7. Influence of decelerating flow on incipient motion of a gravel-bed ...

    Indian Academy of Sciences (India)

    decelerating flow is presented. Experiments were carried out in a flume with two median grain sizes, d 50 = 16·7 mm for a fixed-bed case and d 50 = 8 mm for a mobile bed case. In addition, an effort is made to determine a simplified method for ...

  8. SYNROC powder preparation: preliminary fluid bed tests in a cold-flow unit

    International Nuclear Information System (INIS)

    Peters, P.E.; Ackerman, F.J.; Grens, J.Z.

    1982-01-01

    SYNROC is a titanate-based material which is being developed as a medium for immobilizing high-level nuclear waste. The use of a fluid bed unit for production of SYNROC powder has a precedent in the use of a fluid-bed calciner for high-level waste processing at the Idaho Chemical Processing Plant (Idaho Falls, ID). In order to facilitate the design of a fluid bed and demonstrate its use for SYNROC production, two small units have been constructed, one for low temperature use and a second for actual SYNROC production at temperatures up to 800 0 C. The low-temperature unit is constructed with glass walls to allow observation of the fluidization process, including the onset of fluidization, bed and gas bubble behavior and mixing phenomena. Disturbances caused by side streams entering the bed have been examined. Side streams may represent fuel and oxidizer admission or slurry feed with subsequent flash vaporization of the carrier liquid. This report is a summary of the initial tests made with the low-temperature, glass-walled fluid bed. The tests described include: (1) the measurement of basic fluidization parameters; (2) measurement of the effect of distribution-plate design on bed fluidization; (3) observation of jet penetration, bubble formation and coalescence, and surface behavior; and (4) studies of mixing within the bed

  9. Bed particle entrainment and motion in turbulent open-channel flows: a high-resolution experimental study

    Science.gov (United States)

    Nikora, Vladimir; Cameron, Stuart; Amir, Mohammad; Stewart, Mark; Witz, Matthew

    2015-04-01

    In spite of significant efforts of geoscientists and engineers, the exact mechanics of sediment entrainment and transport by turbulent flows remains unclear and continues to be the focus of many research groups worldwide. The talk outlines current developments in this direction at the University of Aberdeen, where an extensive experimental programme has recently been completed. The experiments were conducted in the Aberdeen Open Channel Facility (AOCF, 20 m long, 1.18 m wide) over wide ranges of flow submergence (1.9-8.0), bulk Reynolds number (4400-83000), and channel aspect ratio (9-39). The flume bed was covered by hexagonally-packed glass beads 16 mm in diameter. For entrainment experiments, selected glass particles were replaced with lighter particles (nylon and delrin). Instantaneous velocity fields before, during, and after entrainment were measured with an advanced multi-mode Particle Image Velocimetry (PIV) system developed by S. Cameron. This system was also used for 3D particle tracking in the entrainment experiments. The main types of experiments included: (1) multi-mode turbulence measurements with fixed-bed conditions to assess the background flow structure (10 min to 120 min duration of velocity records); (2) simultaneous measurements of fluctuating differential pressure acting on 23 fixed particles with in-built pressure sensors, synchronously with PIV; (3) measurements of waiting times for particle entrainment, employing a specially designed system (SMC-1) for automatic placement of the particles on the bed and subsequent measurement of the time before entrainment; (4) long-term direct measurements of the instantaneous drag force acting on a single particle (attached to the bed) at different protrusions, synchronously with PIV; and (5) synchronous measurements of the flow field around a particle before, at, and during entrainment, supplemented with 3D particle tracking. The key results include: (1) the refined turbulence structure of a rough-bed

  10. Factors affecting the growth of Didymosphenia geminata in New Zealand rivers: Flow, bed disturbance, nutrients, light, and seasonal dynamics. (Invited)

    Science.gov (United States)

    Cullis, J. D.; Gillis, C.; Drummond, J. D.; Garcia, T.; Kilroy, C.; Larned, S.; Hassan, M. A.

    2010-12-01

    Didymosphenia geminata (didymo) was introduced into a New Zealand river in 2004, and since then has dramatically spread to cover the beds of many rivers with extremely dense and extensive mats. Successful management is hampered by the fact that much is still unknown about the factors affecting the growth of this nuisance species. We synthesized available data on the distribution of D. geminata in New Zealand rivers to determine how physical and chemical system conditions (flow, bed disturbance, nutrients, and light) affect the growth and persistence of this organism. Here we assess results from bi-weekly surveys performed over a full year on two rivers where didymo was first observed in New Zealand; the Oreti and Mararoa. We used the data to test the hypotheses that the development of thick, dense mats requires high light levels but is inversely proportional to nutrient levels, and that mat persistence is controlled by the frequency of flow events that produce bed sediment transport. Observed regrowth between disturbance events was found to be inversely correlated with nutrient availability. The seasonal availability of light did not correlate with variations in growth rate, but this did not account for specific characteristics of the different sites such as aspect, shading, flow depth and turbidity that will all impact on the amount of available light reaching the streambed. The results clearly indicate that the time-history of flow and nutrient levels is critical to evaluating the growth and persistence of D. geminata and that additional site specific information is necessary to determine the role of bed stability and the amount of available light reaching the streambed.

  11. A hybrid computational approach for the interactions between river flow and porous sediment bed covered with large roughness elements

    Science.gov (United States)

    Liu, X.

    2013-12-01

    In many natural and human-impacted rivers, the porous sediment beds are either fully or partially covered by large roughness elements, such as gravels and boulders. The existence of these large roughness elements, which are in direct contact with the turbulent river flow, changes the dynamics of mass and momentum transfer across the river bed. It also impacts the overall hydraulics in the river channel and over time, indirectly influences the geomorphological evolution of the system. Ideally, one should resolve each of these large roughness elements in a computational fluid model. This approach is apparently not feasible due to the prohibitive computational cost. Considering a typical river bed with armoring, the distribution of sediment sizes usually shows significant vertical variations. Computationally, it poses great challenge to resolve all the size scales. Similar multiscale problem exists in the much broader porous media flow field. To cope with this, we propose a hybrid computational approach where the large surface roughness elements are resolved using immersed boundary method and sediment layers below (usually finer) are modeled by adding extra drag terms in momentum equations. Large roughness elements are digitized using a 3D laser scanner. They are put into the computational domain using the collision detection and rigid body dynamics algorithms which guarantees realistic and physically-correct spatial arrangement of the surface elements. Simulation examples have shown the effectiveness of the hybrid approach which captures the effect of the surface roughness on the turbulent flow as well as the hyporheic flow pattern in and out of the bed.

  12. Numerical Modeling of Reactive Multiphase Flow for FCC and Hot Gas Desulfurization Circulating Fluidized Beds

    Energy Technology Data Exchange (ETDEWEB)

    Miller, Aubrey L. [WSU Research Corporation, Morgantown, WV (USA)

    2005-07-01

    This work was carried out to understand the behavior of the solid and gas phases in a CFB riser. Only the riser is modeled as a straight pipe. A model with linear algebraic approximation to solids viscosity of the form, {musubs} = 5.34{epsisubs}, ({espisubs} is the solids volume fraction) with an appropriate boundary condition at the wall obtained by approximate momentum balance solution at the wall to acount for the solids recirculation is tested against experimental results. The work done was to predict the flow patterns in the CFB risers from available experimental data, including data from a 7.5-cm-ID CFB riser at the Illinois Institute of Technology and data from a 20.0-cm-ID CFB riser at the Particulate Solid Research, Inc., facility. This research aims at modeling the removal of hydrogen sulfide from hot coal gas using zinc oxide as the sorbent in a circulating fluidized bed and in the process indentifying the parameters that affect the performance of the sulfidation reactor. Two different gas-solid reaction models, the unreacted shrinking core (USC) and the grain model were applied to take into account chemical reaction resistances. Also two different approaches were used to affect the hydrodynamics of the process streams. The first model takes into account the effect of micro-scale particle clustering by adjusting the gas-particle drag law and the second one assumes a turbulent core with pseudo-steady state boundary condition at the wall. A comparison is made with experimental results.

  13. Enhanced Small Scale Heat Transfer in Rectangular Channels using Autonomous, Aero-Elastically Fluttering Reeds

    Science.gov (United States)

    Jha, Sourabh; Crittenden, Thomas; Glezer, Ari

    2017-11-01

    The limits of low Reynolds number forced convection heat transport within rectangular, mm-scale channels that model segments of air-cooled heat sinks are overcome by the deliberate formation of unsteady small-scale vortical motions that are induced by autonomous aero-elastic fluttering of cantilevered planar thin-film reeds. The coupled flow-structure interactions between the fluttering reeds and the embedding channel flow and the formation and evolution of the induced unsteady small-scale vortical motions are explored using video imaging and PIV. Concave/convex undulations of the reed's surface that are bounded by the channel's walls lead to the formation and advection of cells of vorticity concentration and ultimately to alternate shedding of spanwise CW and CCW vortices. These vortices scale with the channel height, and result in increased turbulent kinetic energy and enhanced dissipation that persist far downstream from the reed and are reminiscent of a turbulent flow at significantly higher Reynolds numbers (e.g., at Re = 800, TKE increases by 86% ,40 channel widths downstream of reed tip). These small-scale motions lead to strong enhancement in heat transfer that increases with Re (e.g., at Re = 1,000 and 14,000, Nu increases by 36% and 91%, respectively). The utility of this approach is demonstrated in improving the thermal performance of low-Re heat sinks in air-cooled condensers of thermoelectric power plants. NSF-EPRI.

  14. Geomorphic response to flow regulation and channel and floodplain alteration in the gravel-bedded Cedar River, Washington, USA

    Science.gov (United States)

    Gendaszek, Andrew S.; Magirl, Christopher S.; Czuba, Christiana R.

    2012-01-01

    Decadal- to annual-scale analyses of changes to the fluvial form and processes of the Cedar River in Washington State, USA, reveal the effects of flow regulation, bank stabilization, and log-jam removal on a gravel-bedded river in a temperate climate. During the twentieth century, revetments were built along ~ 60% of the lower Cedar River's length and the 2-year return period flow decreased by 47% following flow regulation beginning in 1914. The formerly wide, anastomosing channel narrowed by over 50% from an average of 47 m in 1936 to 23 m in 1989 and became progressively single threaded. Subsequent high flows and localized revetment removal contributed to an increase in mean channel width to about 34 m by 2011. Channel migration rates between 1936 and 2011 were up to 8 m/year in reaches not confined by revetments or valley walls and less than analysis uncertainty throughout most of the Cedar River's length where bank armoring restricted channel movement. In unconfined reaches where large wood and sediment can be recruited, contemporary high flows, though smaller in magnitude than preregulation high flows, form and maintain geomorphic features such as pools, gravel bars, and side channels. Reaches confined by revetments remain mostly unmodified in the regulated flow regime. While high flows are important for maintaining channel dynamics in the Cedar River, their effectiveness is currently reduced by revetments, limited sediment supply, the lack of large wood available for recruitment to the channel, and decreased magnitude since flow regulation.

  15. Large Eddy Simulation of the flow in 90r angled open-channel confluences with discordant beds

    Science.gov (United States)

    Ramos, Pedro; Schindfessel, Laurent; De Mulder, Tom

    2017-04-01

    The aim of the present contribution is to investigate the effect of difference in bed elevations of the tributary and main channel in a 90˚ angled open-channel confluence onto the hydrodynamics. Large Eddy Simulations (LES) are used to investigate the three-dimensional complex flow patterns for four different discordance ratios (ΔzT/hd = 0, 0.1, 0.25 and 0.4), with geometries previously studied by other authors, whose data will be used for comparison purposes. The values of the ratio between the upstream main channel discharge and the total combined discharge varies between 0.083 and 0.917. With LES, it is possible to resolve a portion of the turbulent motions, which is beneficial to the accuracy of the simulations. This contribution develops further analysis on some findings of the aforementioned studies, mostly regarding the role of the bed discordance on the recirculation zone dimensions and on the influence of the tributary flow on the main stream. Points of interest are the orientation of the tributary's inflow angle and the dimensions of the separation zone. These parameters are important for the longitudinal momentum balance, which determines the head losses occurring at the confluence. Additionally, the distribution of Turbulent Kinetic Energy (TKE) and bed shear stresses are studied. Previous studied indicated that the presence of a bed discordance has a pronounced effect on these points of interest. The present contribution elaborates these findings and adds knowledge from time-resolved simulations. Since in a LES the flow and turbulence are for the most part resolved, it enables a thorough study of the hydrodynamics in an open-channel confluence, of which the understanding of the physical phenomena occurring in natural confluences will benefit.

  16. Entrainment of bed material by Earth-surface mass flows: review and reformulation of depth-integrated theory

    Science.gov (United States)

    Iverson, Richard M.; Chaojun Ouyang,

    2015-01-01

    Earth-surface mass flows such as debris flows, rock avalanches, and dam-break floods can grow greatly in size and destructive potential by entraining bed material they encounter. Increasing use of depth-integrated mass- and momentum-conservation equations to model these erosive flows motivates a review of the underlying theory. Our review indicates that many existing models apply depth-integrated conservation principles incorrectly, leading to spurious inferences about the role of mass and momentum exchanges at flow-bed boundaries. Model discrepancies can be rectified by analyzing conservation of mass and momentum in a two-layer system consisting of a moving upper layer and static lower layer. Our analysis shows that erosion or deposition rates at the interface between layers must in general satisfy three jump conditions. These conditions impose constraints on valid erosion formulas, and they help determine the correct forms of depth-integrated conservation equations. Two of the three jump conditions are closely analogous to Rankine-Hugoniot conditions that describe the behavior of shocks in compressible gasses, and the third jump condition describes shear traction discontinuities that necessarily exist across eroding boundaries. Grain-fluid mixtures commonly behave as compressible materials as they undergo entrainment, because changes in bulk density occur as the mixtures mobilize and merge with an overriding flow. If no bulk density change occurs, then only the shear-traction jump condition applies. Even for this special case, however, accurate formulation of depth-integrated momentum equations requires a clear distinction between boundary shear tractions that exist in the presence or absence of bed erosion.

  17. Coupled three-layer model for turbulent flow over large-scale roughness: On the hydrodynamics of boulder-bed streams

    Science.gov (United States)

    Pan, Wen-hao; Liu, Shi-he; Huang, Li

    2018-02-01

    This study developed a three-layer velocity model for turbulent flow over large-scale roughness. Through theoretical analysis, this model coupled both surface and subsurface flow. Flume experiments with flat cobble bed were conducted to examine the theoretical model. Results show that both the turbulent flow field and the total flow characteristics are quite different from that in the low gradient flow over microscale roughness. The velocity profile in a shallow stream converges to the logarithmic law away from the bed, while inflecting over the roughness layer to the non-zero subsurface flow. The velocity fluctuations close to a cobble bed are different from that of a sand bed, and it indicates no sufficiently large peak velocity. The total flow energy loss deviates significantly from the 1/7 power law equation when the relative flow depth is shallow. Both the coupled model and experiments indicate non-negligible subsurface flow that accounts for a considerable proportion of the total flow. By including the subsurface flow, the coupled model is able to predict a wider range of velocity profiles and total flow energy loss coefficients when compared with existing equations.

  18. Robust Reed Solomon Coded MPSK Modulation

    Directory of Open Access Journals (Sweden)

    Emir M. Husni

    2014-10-01

    Full Text Available In this paper, construction of partitioned Reed Solomon coded modulation (RSCM, which is robust for the additive white Gaussian noise channel and a Rayleigh fading channel, is investigated. By matching configuration of component codes with the channel characteristics, it is shown that this system is robust for the Gaussian and a Rayleigh fading channel. This approach is compared with non-partitioned RSCM, a Reed Solomon code combined with an MPSK signal set using Gray mapping; and block coded MPSK modulation using binary codes, Reed Muller codes. All codes use hard decision decoding algorithm. Simulation results for these schemes show that RSCM based on set partitioning performs better than those that are not based on set partitioning and Reed Muller Coded Modulation across a wide range of conditions. The novel idea here is that in the receiver, we use a rotated 2^(m+1-PSK detector if the transmitter uses a 2^m-PSK modulator.

  19. Influence of bed material entrainment and non-Newtonian rheology on turbulent geophysical flows dynamics. Numerical study

    Science.gov (United States)

    Eglit, M. E.; Yakubenko, A. E.; Yakubenko, T. A.

    2017-10-01

    This paper deals with the mathematical and numerical modeling of the propagation stage of geophysical gravity-driven flows, such as snow avalanches, mudflows, and rapid landslides. New mathematical models are presented which are based on full, not-depth-averaged equations of mechanics of continuous media. The models account for three important issues: non-Newtonian rheology of the moving material, entrainment of the bed material by the flow, and turbulence. The main objective is to investigate the effect of these three factors on the flow dynamics and on the value of the entrainment rate. To exclude the influence of many other factors, e.g., the complicated slope topography, only the motion down a long uniform slope with a constant inclination angle is studied numerically. Moreover, the entire flow from the front to the rear area was not modeled, but only its middle part where the flow is approximately uniform in length. One of the qualitative results is that in motion along homogeneous slope the mass entrainment increases the flow velocity and depth while the entrainment rate at large time tends to become constant which depends on the physical properties of the flow and the underlying material but not on the current values of the flow velocity and depth.

  20. Hydrodynamics of Flow Obstructed by Inline and Eccentrically-Arranged Circular Piers on a Horizontal Bed Surface

    Science.gov (United States)

    Jaman, Hasanur; Das, Subhasish; Das, Rajib; Mazumdar, Asis

    2017-06-01

    An attempt has been made to study and analyse the hydrodynamic effects of turbulent flow including its pattern and characteristics around three identical circular shaped piers. Experimentation was conducted under clear-water scour condition. Three pier groups were placed with inline and eccentric arrangement in tandem manner on a flume. Two piers were positioned inline along the flow direction and third pier was placed eccentrically in the middle of two inline piers having a transverse distance equal to three times of pier width. Three dimensional velocities were gauged at a horizontal plane located at 4% depth above the zero bed level. The readings were captured in the Cartesian coordinate-system to compute the time-mean longitudinal, transversal and vertical velocities. The hydrodynamic consequences of three piers arrangement near the horizontal bed were investigated. The contour profile and variations of time aggregated mean velocity components, kinetic energy and turbulence intensities are measured or determined and analysed. Velocity vectors and absolute velocity at horizontal plane obtained from velocity measuring areas are utilised to explain further hydrodynamic flow features. The measured depth for scour at equilibrium state for the eccentric middle pier is observed higher than the inline front and inline rear circular piers. The three pier group positioning and the interfering between the circular piers act an important function in flow characteristics and for creating and forming the larger scoured depth around the eccentric middle pier.

  1. On numerical model of one-dimensional time-dependent gas flows through bed of encapsulated phase change material

    Science.gov (United States)

    Lutsenko, N. A.; Fetsov, S. S.

    2017-10-01

    Mathematical model and numerical method are proposed for investigating the one-dimensional time-dependent gas flows through a packed bed of encapsulated Phase Change Material (PCM). The model is based on the assumption of interacting interpenetrating continua and includes equations of state, continuity, momentum conservation and energy for PCM and gas. The advantage of the method is that it does not require predicting the location of phase transition zone and can define it automatically as in a usual shock-capturing method. One of the applications of the developed numerical model is the simulation of novel Adiabatic Compressed Air Energy Storage system (A-CAES) with Thermal Energy Storage subsystem (TES) based on using the encapsulated PCM in packed bed. Preliminary test calculations give hope that the method can be effectively applied in the future for modelling the charge and discharge processes in such TES with PCM.

  2. Using Natural Boundary Conditions to Probe the Internal Dynamics of Pyroclastic Flows: Mass, Enthalpy and Momentum Transfer at the Flow-Bed Interface

    Science.gov (United States)

    Dufek, J.; Bergantz, G. W.; Manga, M.

    2006-12-01

    The interaction of pyroclastic density currents with their substrate plays a significant role in the transport and deposition of these flows. The basal particle concentration of these flows will ultimately determine the mechanism of mass, enthalpy and momentum transfer and the sensitivity of these flows to bed roughness, topography and even their ability to cross bodies of water. In order to probe the internal structure of these flows we used an Eulerian-Eulerian-Lagrangian (EEL) computational approach coupled with an examination of ignimbrite deposits of the Kos Plateau Tuff (KPT) and the near-shore deposits of the 2003 Montserrat dome collapse (Allen and Cas, 2001; Edmonds and Herd, 2005). In particular, the KPT eruption provides a unique opportunity to compare flows that have traversed a body of water (and thereby filtering out their bed-load) versus flows that have traveled over-land. The examined Montserrat pyroclastic flows also encounter the ocean, and comparison with observations of the recently produced near-shore deposits allow us to access the near-surface energy transfer required to produce the observed steam explosions and the mass transfer necessary to produce tsunami. This coupled deposit-driven and numerical investigation reveals that energy-dissipation at the basal boundary is one of the primary factors determining the run-out distance of pyroclastic flows. A significant portion of the momentum of over-land flows is transported in a bed-load region dominated by numerous particle-particle and particle-boundary interactions. Mass and energy transfer in the near shore environment produce tsunami and steam explosions, which result in preferential fining in the proximal deposits and a source of water vapor to the propagating currents. However, the simulations indicate the internal structure and head of the pyroclastic density current are not significantly impacted by the steam explosions after they have traveled several kilometers away from the shore as

  3. Flow regime map for two dimensional spouted bed and comparison with simulation by discrete element method; Nijigen funryuso no ryudo jotaizu to risan yosoho ni yoru shumyureshon kekka tono hikaku

    Energy Technology Data Exchange (ETDEWEB)

    Tsuji, T.; Chiba, T.; Shibata, T.; Uemaki, O.; Ito, H. [Hokkaido University, Hokkaido (Japan)

    1999-11-10

    A flow regime map for a two-dimensional spouted bed is constructed from the experimental conditions that cause the fixed bed, spouted bed, bubbling fluidized bed and slugging bed. The map is compared to the one that is made from the simulations using P-TAK, a general-purpose simulation code of gas and particle flow by the discrete element method. Both maps coincide very well, indicating that the discrete element method has big potential for predicting critical flow conditions such as the minimum spouting velocity or the maximum spoutable bed height. (author)

  4. Nonlinear dynamics of musical reed and brass wind instruments

    Science.gov (United States)

    Campbell, D. M.

    1999-06-01

    A musical wind instrument transforms a constant pressure input from the player's mouth into a fluctuating pressure output in the form of a radiating sound wave. In reed woodwind and brass instruments, this transformation is achieved through a nonlinear coupling between two vibrating systems: the flow control valve formed by the mechanical reed or the lips of the player, and the air column contained by the pipe. Although the basic physics of reed wind instruments was developed by Helmholtz in the nineteenth century, the application of ideas from the modern theory of nonlinear dynamics has led to recent advances in our understanding of some musically important features of wind instrument behaviour. As a first step, the nonlinear aspects of the musical oscillator can be considered to be concentrated in the flow control valve; the air column can be treated as a linear vibrating system, with a set of natural modes of vibration corresponding to the standing waves in the pipe. Recent models based on these assumptions have had reasonable success in predicting the threshold blowing pressure and sounding frequency of a clarinet, as well as explaining at least qualitatively the way in which the timbre of the sound varies with blowing pressure. The situation is more complicated for brass instruments, in which the player's lips provide the flow valve. Experiments using artificial lips have been important in permitting systematic studies of the coupling between lips and air column; the detailed nature of this coupling is still not fully understood. In addition, the assumption of linearity in the air column vibratory system sometimes breaks down for brass instruments. Nonlinear effects in the propagation of high amplitude sound waves can lead to the development of shock waves in trumpets and trombones, with important musical consequences.

  5. Purification performances of common reed beds based on the ...

    African Journals Online (AJOL)

    SARAH

    2013-11-30

    Nov 30, 2013 ... mg/L; 168 mg/L; and 4.5 mg/L respectively in Chemical Oxygen Demand (COD), Biochemical Oxygen Demand at 5 days of incubation (BOD5), Total Suspended Solid (TSS), Total Kjeldahl Nitrogen (TKN), and Total. Phosphorus (TP). At the end of the study, the treatment performance results showed the ...

  6. Purification performances of common reed beds based on the ...

    African Journals Online (AJOL)

    SARAH

    2013-11-30

    BOD5), membrane manometers. (Oxitop) were used. Pre-packed kits (DR Hach Lange) and a spectrophotometer (DR 2800) permitted the analysis of the Total Organic Carbon (TOC) and the. Dissolved Organic Carbon (DOC).

  7. Spatial distribution of impacts to channel bed mobility due to flow regulation, Kootenai River, USA

    Science.gov (United States)

    Michael Burke; Klaus Jorde; John M. Buffington; Jeffrey H. Braatne; Rohan Benjakar

    2006-01-01

    The regulated hydrograph of the Kootenai River between Libby Dam and Kootenay Lake has altered the natural flow regime, resulting in a significant decrease in maximum flows (60% net reduction in median 1-day annual maximum, and 77%-84% net reductions in median monthly flows for the historic peak flow months of May and June, respectively). Other key hydrologic...

  8. Building population balance model for fluidized bed melt granulation: lessons from kinetic theory of granular flow

    NARCIS (Netherlands)

    Tan, H.S.; Goldschmidt, M.J.V.; Boerefijn, R.; Hounslow, M.J.; Salman, A.; Kuipers, J.A.M.

    2004-01-01

    The purpose of this paper is to develop a theoretically sound basis for the equi-partition of kinetic energy (EKE) kernel recently developed by our group to describe the evolution of granule size distributions in fluidized bed granulation. The approach taken is to show first by distinct element

  9. Flow characteristics in a large jetting fluidized bed with two nozzles

    Energy Technology Data Exchange (ETDEWEB)

    Guo, Q.; Liu, Z.; Zhang, J.

    2000-03-01

    Jetting fluidized beds are widely used in a number of industrial processes because of various advantages, such as high rates of heat and mass transfer and chemical reaction. These processes include catalytic and flame processes, combustion and gasification of coal, treatment of wastes, cleaning of dusty gases, coating, and granulation. The penetration depth for millet (1.64 mm) as fluidization particles (Geldart group D) was determined in a large jetting fluidized bed of 0.5 m inner diameter and 8 m height and with two nozzles is precorded by a video camera and analyzed frame by frame. Based on experimental data, an empirical correlation for the penetration depth is proposed. Experimental results indicate that the penetration depth increases with an increase in the jetting velocity. Under the same jet gas velocity, the penetration depth decreases as the nozzle distance decreases. Meanwhile, a simple correlation for jet coalescence height is found. A radial voidage profile in the jetting fluidized bed is investigated using a PC-4 fiber optic concentration probe, the effects of jet gas velocity, and the distance between two nozzles on the radial voidage distribution, and a radial profile with unequal jet gas velocity in a jetting fluidized bed is studied.

  10. A study on one-dimensional and discontinuous river flows with mobile beds

    NARCIS (Netherlands)

    Sieben, A.

    1995-01-01

    This report focusses on discontinuous behaviour of hydraulics and morphology in rivers. The varying widths, slopes and bed levels that can be observed in mountain rivers can induce rapid, or discontinuous changes at a short lengthscale. When present, these discontinuities have a major impact on

  11. Investigation of flow dynamics of liquid phase in a pilot-scale trickle bed reactor using radiotracer technique.

    Science.gov (United States)

    Pant, H J; Sharma, V K

    2016-10-01

    A radiotracer investigation was carried out to measure residence time distribution (RTD) of liquid phase in a trickle bed reactor (TBR). The main objectives of the investigation were to investigate radial and axial mixing of the liquid phase, and evaluate performance of the liquid distributor/redistributor at different operating conditions. Mean residence times (MRTs), holdups (H) and fraction of flow flowing along different quadrants were estimated. The analysis of the measured RTD curves indicated radial non-uniform distribution of liquid phase across the beds. The overall RTD of the liquid phase, measured at the exit of the reactor was simulated using a multi-parameter axial dispersion with exchange model (ADEM), and model parameters were obtained. The results of model simulations indicated that the TBR behaved as a plug flow reactor at most of the operating conditions used in the investigation. The results of the investigation helped to improve the existing design as well as to design a full-scale industrial TBR for petroleum refining applications. Copyright © 2016 Elsevier Ltd. All rights reserved.

  12. Evaluation of the hydrological flow paths in a gravel bed filter modeling a horizontal subsurface flow wetland by using a multi-tracer experiment.

    Science.gov (United States)

    Birkigt, Jan; Stumpp, Christine; Małoszewski, Piotr; Nijenhuis, Ivonne

    2018-04-15

    In recent years, constructed wetland systems have become into focus as means of cost-efficient organic contaminant management. Wetland systems provide a highly reactive environment in which several removal pathways of organic chemicals may be present at the same time; however, specific elimination processes and hydraulic conditions are usually separately investigated and thus not fully understood. The flow system in a three dimensional pilot-scale horizontal subsurface constructed wetland was investigated applying a multi-tracer test combined with a mathematical model to evaluate the flow and transport processes. The results indicate the existence of a multiple flow system with two distinct flow paths through the gravel bed and a preferential flow at the bottom transporting 68% of tracer mass resulting from the inflow design of the model wetland system. There the removal of main contaminant chlorobenzene was up to 52% based on different calculation approaches. Determined retention times in the range of 22d to 32.5d the wetland has a heterogeneous flow pattern. Differences between simulated and measured tracer concentrations in the upper sediment indicate diffusion dominated processes due to stagnant water zones. The tracer study combining experimental evaluation with mathematical modeling demonstrated the complexity of flow and transport processes in the constructed wetlands which need to be taken into account during interpretation of the determining attenuation processes. Copyright © 2017 Elsevier B.V. All rights reserved.

  13. Modeling the methanolysis of triglyceride catalyzed by immobilized lipase in a continuous-flow packed-bed reactor

    International Nuclear Information System (INIS)

    Tran, Dang-Thuan; Lin, Yi-Jan; Chen, Ching-Lung; Chang, Jo-Shu

    2014-01-01

    Highlights: • A Burkholderia lipase was immobilized on alkyl-grafted celite carriers. • Celite-alkyl-lipase catalyzed the methanolysis of triglyceride in packed-bed reactor. • The kinetics of the enzymatic transesterification follows Ping Pong Bi Bi mechanism. • Models were developed to discuss the mass transfer and enzyme kinetics in the PBR. - Abstract: A Burkholderia lipase was immobilized on celite grafted with long alkyl groups. The immobilized lipase-catalyzed methanolysis of sunflower oil in a packed-bed reactor (PBR) follows the Ping Pong Bi Bi mechanism. The external mass transfer and enzymatic reaction that simultaneously occurred in the PBR were investigated via the mathematical models. The overall biodiesel production in the PBR was verified to work in an enzymatic reaction-limited regime. Triglyceride conversion and biodiesel yield were higher under a lower reactant feeding rate, while a larger amount of biocatalyst would be required to achieve the designated conversion rate if a higher reactant feeding rate was employed. The PBR can achieve nearly complete conversion of triglyceride at a biocatalyst bed height of 60 cm (ca. 29 g biocatalyst) and a flow rate of 0.1 ml min −1 , whereas the biodiesel yield was lower than 67%, probably due to the positional specificity of Burkholderia lipase and the accumulation of glycerol

  14. Effect of the submergence, the bed form geometry, and the speed of the surface water flow on the mitigation of pesticides in agricultural ditches

    Science.gov (United States)

    Boutron, Olivier; Margoum, Christelle; Chovelon, Jean-Marc; Guillemain, CéLine; Gouy, VéRonique

    2011-08-01

    Pesticides, which have been extensively used in agriculture, have become a major environmental issue, especially regarding surface and groundwater contamination. Of particular importance are vegetated farm drainage ditches, which can play an important role in the mitigation of pesticide contamination by adsorption onto ditch bed substrates. This role is, however, poorly understood, especially regarding the influence of hydrodynamic parameters, which make it difficult to promote best management practice of these systems. We have assessed the influence of three of these parameters (speed of the surface water flow, submergence, and geometrical characteristics of the bed forms) on the transfer and adsorption of selected pesticides (isoproturon, diuron, tebuconazole, and azoxystrobin) into the bed substrate by performing experiments with a tilted experimental flume, using hemp fibers as a standard of natural organic substrates that are found at the bottom of agricultural ditches. Results show the transfer of pesticides from surface water flow into bed substrate is favored, both regarding the amounts transferred into the bed substrate and the kinetics of the transfer, when the surface water speed and the submergence increase and when the bed forms are made of rectangular shapes. Extrapolation of flume data over a distance of several hundred meters suggests that an interesting possibility for improving the mitigation of pesticides in ditches would be to increase the submergence and to favor bed forms that tend to enhance perturbations and subsequent infiltration of the surface water flow.

  15. Low genetic differentiation among reed warbler Acrocephalus scirpaceus populations across Europe

    Czech Academy of Sciences Publication Activity Database

    Procházka, Petr; Stokke, B. G.; Jensen, H.; Fainová, Drahomíra; Bellinvia, Erica; Fossoy, F.; Vikan, J. R.; Bryja, Josef; Soler, M.

    2011-01-01

    Roč. 42, č. 2 (2011), s. 103-113 ISSN 0908-8857 R&D Projects: GA AV ČR KJB600930508; GA MŠk LC06073 Institutional research plan: CEZ:AV0Z60930519 Keywords : Acrocephalus scirpaceus * gene flow * isolation by distance * microsatellites * migration * reed warbler Subject RIV: EG - Zoology Impact factor: 2.280, year: 2011

  16. Reed Canary Grass Project. Development of a new crop production system based on delayed harvesting and a system for its combined processing to chemical pulp and bio fuel powder

    Energy Technology Data Exchange (ETDEWEB)

    Olsson, Rolf (ed.) (and others)

    2004-07-01

    content. The ash is also very voluminous and this results in difficulties to burn reed canary grass in equipment designed for wood pellet combustion. The ash fusibility temperatures of RCG are high but the initial deformation temperature is, especially in reducing conditions, very low (980 deg C) and may cause partial deformation of fuel ash. The deformation can then cause bridging between the pellets and prevent the air to pass through the bed. Special attention has to be paid to mix the fuel bed thus allowing combustion air to flow into contact with combustible matter. It is however possible to design also pellet combustion systems for RCG meal pellets but they are not on a market now. RCG is easier to burn as briquettes. The results thus show that the high ash and silica content means that specially designed boilers, which can handle the high ash amount, must be developed. [abstract truncated

  17. Magnetic fabric of sheared till: A strain indicator for evaluating the bed deformation model of glacier flow

    Science.gov (United States)

    Hooyer, T.S.; Iverson, N.R.; Lagroix, F.; Thomason, J.F.

    2008-01-01

    Wet-based portions of ice sheets may move primarily by shearing their till beds, resting in high sediment fluxes and the development of subglacial landforms. This model of glacier movement, which requires high bed shear strains, can be tested using till microstructural characteristics that evolve during till deformation. Here we examine the development of magnetic fabric using a ring shear device to defom two Wisconsin-age basal tills to shear strains as high as 70. Hysteresis experiments and the dependence of magnetic susceptibility of these tills on temperature demonstrate that anisotropy of magnetic susceptibility (AMS) develops during shear due to the rotation of primarily magnetite particles that are silt sized or smaller. At moderate shear strains (???6-25), principal axes of maximum magnetic susceptibility develop a strong fabric (S1 eignevalues of 0.83-0.96), without further strengthening at higher strains, During deformation, directions of maximum susceptibility cluster strongly in the direction of shear and plunge 'up-glacier,' consistent with the behavior of pebbles and sand particles studied in earlier experiments. In contrast, the magnitude of AMS does not vary systematically with strain and is small relative to its variability among samples; this is because most magnetite grains are contained as inclusions in larger particles and hence do not align during shear. Although processes other than pervasive bed deformation may result in strong flow parallel fabrics, AMS fabrics provide a rapid and objective means of identifying basal tills that have not been sheared sufficiently to be compatible with the bed deformation model. Copyright 2008 by the American Geophysical Union.

  18. Flow characteristics analysis of purge gas in unitary pebble beds by CFD simulation coupled with DEM geometry model for fusion blanket

    Energy Technology Data Exchange (ETDEWEB)

    Chen, Youhua [University of Science and Technology of China, Hefei, Anhui, 230027 (China); Institute of Plasma Physics, Chinese Academy of Sciences, Hefei, Anhui, 230031 (China); Chen, Lei [Institute of Plasma Physics, Chinese Academy of Sciences, Hefei, Anhui, 230031 (China); Liu, Songlin, E-mail: slliu@ipp.ac.cn [Institute of Plasma Physics, Chinese Academy of Sciences, Hefei, Anhui, 230031 (China); Luo, Guangnan [University of Science and Technology of China, Hefei, Anhui, 230027 (China); Institute of Plasma Physics, Chinese Academy of Sciences, Hefei, Anhui, 230031 (China)

    2017-01-15

    Highlights: • A unitary pebble bed was built to analyze the flow characteristics of purge gas based on DEM-CFD method. • Flow characteristics between particles were clearly displayed. • Porosity distribution, velocity field distribution, pressure field distribution, pressure drop and the wall effects on velocity distribution were studied. - Abstract: Helium is used as the purge gas to sweep tritium out when it flows through the lithium ceramic and beryllium pebble beds in solid breeder blanket for fusion reactor. The flow characteristics of the purge gas will dominate the tritium sweep capability and tritium recovery system design. In this paper, a computational model for the unitary pebble bed was conducted using DEM-CFD method to study the purge gas flow characteristics in the bed, which include porosity distribution between pebbles, velocity field distribution, pressure field distribution, pressure drop as well as the wall effects on velocity distribution. Pebble bed porosity and velocity distribution with great fluctuations were found in the near-wall region and detailed flow characteristics between pebbles were displayed clearly. The results show that the numerical simulation model has an error with about 11% for estimating pressure drop when compared with the Ergun equation.

  19. Squeeze-film flow between a flat impermeable bearing and an anisotropic porous bed

    Science.gov (United States)

    Karmakar, Timir; Raja Sekhar, G. P.

    2018-04-01

    We consider a theoretical model of the squeeze film in the presence of a porous bed. The gap between the porous bed and the bearing is assumed to be filled with a Newtonian fluid. We use the Navier-Stokes equation in the fluid region and the Darcy equation in the fluid filled porous region. Lubrication approximation is used to derive the corresponding evolution equation for the film thickness. We use G. S. Beavers and D. D. Joseph ["Boundary conditions at a naturally permeable wall," J. Fluid. Mech. 30, 197-207 (1967)] and M. Le Bars and M. G. Worster ["Interfacial conditions between a pure fluid and a porous medium: Implications for binary alloy solidification," J. Fluid. Mech. 550, 149-173 (2006)] condition at the liquid porous interface and present a detailed analysis on the corresponding impact. We assume that the porous bed is anisotropic in nature with permeabilities K2 and K1 along the principal axes. Accordingly, the anisotropic angle ϕ is taken as the angle between the horizontal direction and principal axis with permeability K2. We show that the anisotropic permeability ratio and the anisotropic angle make a significant influence on the contact time, flux, velocity, etc. Contact time to meet the porous bed when a bearing approaches under a constant prescribed load is estimated. We present some important findings (relevant to the knee joint) based on the anisotropic properties of the human cartilage. For a prescribed constant load, we have estimated the time duration, during which a healthy human knee remains fluid lubricated.

  20. Model investigations 3D of gas-powder two phase flow in descending packed bed in metallurgical shaft furnaces

    OpenAIRE

    B. Panic; K. Janiszewski

    2014-01-01

    This paper presents the second phase of model investigations of static pressure radial distribution conducted on 4 levels of bed height. During the phase the diameter of glass bed particles was increased, blast-furnace pellets were introduced as bed and iron powder was used as powder. Experiments were carried out with regard to gas velocity, bed and powder type and size of bed particles. The radial distribution of 3 fractions of powder accumulated in the bed – static powder, dynamic powder an...

  1. Adjustable reed for weaving net-shaped tailored fabrics

    Science.gov (United States)

    Farley, Gary L.

    1994-06-01

    The invention is an apparatus and method for forming woven fabrics through the use of an adjustable reed. The adjustable reed has multiple groups of reed wires that guide the warp yarns. The groups of reed wires move on reed rails parallel to the warp direction. In addition, rail expanders permit the space between the reed wires to be modified and telescoping rods attached to the rail sliders can be turned to permit the reed wires to be skewed to alter the fill yarn angle. These adjustments to the reed permit simultaneous variation of fill yarn angles and fabric widths and allow these variations to be made during fabrication, without the need to halt production.

  2. Effects of uncertain topographic input data on two-dimensional modeling of flow hydraulics, habitat suitability, and bed mobility

    Science.gov (United States)

    Legleiter, C. J.; McDonald, R.; Kyriakidis, P. C.; Nelson, J. M.

    2009-12-01

    Numerical models of flow and sediment transport increasingly are used to inform studies of aquatic habitat and river morphodynamics. Accurate topographic information is required to parameterize such models, but this fundamental input is typically subject to considerable uncertainty, which can propagate through a model to produce uncertain predictions of flow hydraulics. In this study, we examined the effects of uncertain topographic input on the output from FaSTMECH, a two-dimensional, finite difference flow model implemented on a regular, channel-centered grid; the model was applied to a simple, restored gravel-bed river. We adopted a spatially explicit stochastic simulation approach because elevation differences (i.e., perturbations) at one node of the computational grid influenced model predictions at nearby nodes, due to the strong coupling between proximal locations dictated by the governing equations of fluid flow. Geostatistical techniques provided an appropriate framework for examining the impacts of topographic uncertainty by generating many, equally likely realizations, each consistent with a statistical model summarizing the variability and spatial structure of channel morphology. By applying the model to each realization in turn, a distribution of model outputs was generated for each grid node. One set of realizations, conditioned to the available survey data and progressively thinned versions thereof, was used to quantify the effects of sampling strategy on topographic uncertainty and hence the uncertainty of model predictions. This analysis indicated that as the spacing between surveyed cross-sections increased, the reach-averaged ensemble standard deviation of water surface elevation, depth, velocity, and boundary shear stress increased as well, for both baseflow conditions and for a discharge of ~75% bankfull. A second set of realizations was generated by retaining randomly selected subsets of the original survey data and used to investigate the

  3. Simulation of gas and particle flow in a circulating fluidized bed; Kaasu- ja kiintoainevirtauksen simulointi kiertoleijukattilassa

    Energy Technology Data Exchange (ETDEWEB)

    Kallio, S. [Aabo Akademi, Turku (Finland). Inst. of Heat Engineering

    1996-12-01

    The aim of this work was to study the effects of different parameters on the flow behaviour in a CFB riser by means of empirical models based on measurement data and a computer code based on macroscopic equations for multiphase flow. The effects of primary air velocity and riser geometry have been observed in the results. Simulation of secondary air flow proved to be problematic with the software used. In the project, also analyses of measurement data from cold model experiments has been performed. Moreover, the possibilities to use commercial CFD codes for simulation of gas-solids flow were investigated. The code FLUENT seemed promising. (author)

  4. Study of Co-Current and Counter-Current Gas-Liquid Two-Phase Flow Through Packed Bed in Microgravity

    Science.gov (United States)

    Revankar, Shripad T.

    2002-11-01

    The main goal of the project is to obtain new experimental data and development of models on the co-current and counter-current gas-liquid two-phase flow through a packed bed in microgravity and characterize the flow regime transition, pressure drop, void and interfacial area distribution, and liquid hold up. Experimental data will be obtained for earth gravity and microgravity conditions. Models will be developed for the prediction of flow regime transition, void fraction distribution and interfacial area concentration, which are key parameters to characterize the packed bed performance. Thus the specific objectives of the proposed research are to: (1) Develop experiments for the study of the gas liquid two-phase flow through the packed bed with three different flow combinations: co-current down flow, co-current upflow and counter current flow. (2) Develop pore scale and bed scale two-phase instrumentation for measurement of flow regime transition, void distribution and gas-liquid interfacial area concentration in the packed bed. (3) Obtain database on flow regime transition, pressure drop, void distribution, interfacial area concentration and liquid hold up as a function of bed characteristics such as bed particle size, porosity, and liquid properties such as viscosity and surface tension. (4) Develop mathematical model for flow regime transition, void fraction distribution and interfacial area concentration for co-current gas-liquid flow through the porous bed in gravity and micro gravity conditions.(4) Develop mathematical model for the flooding phenomena in counter-current gas-liquid flow through the porous bed in gravity and micro gravity conditions. The present proposal addresses the most important topic of HEDS-specific microgravity fluid physics research identified by NASA 's one of the strategic enterprises, OBPR Enterprise. The proposed project is well defined and makes efficient use of the ground-based parabolic flight research aircraft facility. The

  5. Basal interstitial water pressure in laboratory debris flows over a rigid bed in an open channel

    Directory of Open Access Journals (Sweden)

    N. Hotta

    2012-08-01

    Full Text Available Measuring the interstitial water pressure of debris flows under various conditions gives essential information on the flow stress structure. This study measured the basal interstitial water pressure during debris flow routing experiments in a laboratory flume. Because a sensitive pressure gauge is required to measure the interstitial water pressure in shallow laboratory debris flows, a differential gas pressure gauge with an attached diaphragm was used. Although this system required calibration before and after each experiment, it showed a linear behavior and a sufficiently high temporal resolution for measuring the interstitial water pressure of debris flows. The values of the interstitial water pressure were low. However, an excess of pressure beyond the hydrostatic pressure was observed with increasing sediment particle size. The measured excess pressure corresponded to the theoretical excess interstitial water pressure, derived as a Reynolds stress in the interstitial water of boulder debris flows. Turbulence was thought to induce a strong shear in the interstitial space of sediment particles. The interstitial water pressure in boulder debris flows should be affected by the fine sediment concentration and the phase transition from laminar to turbulent debris flow; this should be the subject of future studies.

  6. Investigation of gas–solids flow in a circulating fluidized bed using 3D electrical capacitance tomography

    International Nuclear Information System (INIS)

    Mao, Mingxu; Ye, Jiamin; Wang, Haigang; Yang, Wuqiang

    2016-01-01

    The hydrodynamics of gas–solids flow in the bottom of a circulating fluidized bed (CFB) are complicated. Three-dimensional (3D) electrical capacitance tomography (ECT) has been used to investigate the hydrodynamics in risers of different shapes. Four different ECT sensors with 12 electrodes each are designed according to the dimension of risers, including two circular ECT sensors, a square ECT sensor and a rectangular ECT sensor. The electrodes are evenly arranged in three planes to obtain capacitance in different heights and to reconstruct the 3D images by linear back projection (LBP) algorithm. Experiments were carried out on the four risers using sands as the solids material. The capacitance and differential pressure are measured under the gas superficial velocity from 0.6 m s −1 to 3.0 m s −1 with a step of 0.2 m s −1 . The flow regime is investigated according to the solids concentration and differential pressure. The dynamic property of bubbling flows is analyzed theoretically and the performance of the 3D ECT sensors is evaluated. The experimental results show that 3D ECT can be used in the CFB with different risers to predict the hydrodynamics of gas–solids bubbling flows. (paper)

  7. Assessment of morphological changes induced by flow and flood pulses in a gravel bed braided river: The Tagliamento River (Italy)

    Science.gov (United States)

    Bertoldi, W.; Zanoni, L.; Tubino, M.

    2010-01-01

    Large gravel-bed braided rivers show a highly dynamic evolution, where even moderate flow pulses can produce significant morphological adjustment. An estimation of network variations is needed by river authorities as well as by ecologists for better managing river ecosystems. However, few field investigations have been performed to measure the effect of unsteady discharges in braided rivers. In this paper we report on the morphological changes induced by six different floods in a 1-km-long reach of the Tagliamento River, Italy. Topographic surveys were performed after each significant flood, and an automatic digital camera continuously monitored the planimetric configuration. Repeated measurements of cross section profiles allowed the quantification of the transported sediments volume and, in particular, provided a basis to estimate the percentage of the floodplain subject to morphological evolution. Data analysis showed a good relationship between peak flow level, active width, and mean bed level changes. Similarly, lateral channel shifting is likely to increase for larger floods. Monitoring of a range of discharges up to bankfull conditions revealed a fundamental difference between flow pulses (events on the average occurring one or more times per year) and flood pulses (with a return period larger than two years). The morphological evolution in the former case is mainly limited to a few active branches and is locally driven by bank erosion at the bend apex. On the other hand, larger floods induce a complete reworking of the network configuration, where bifurcations and confluences play a crucial role. Single morphological units (like branches, nodes, bars) are no longer recognizable after this type of event. Braided rivers are therefore characterized by the occurrence of two different spatial and temporal scales that force the ecosystem dynamics.

  8. Observation and simulation of heterogeneous 2D water and solute flow processes in ditch beds for subsequent catchment modelling

    Science.gov (United States)

    Dages, Cecile; Samouelian, Anatja; Lanoix, Marthe; Dollinger, Jeanne; Chakkour, Sara; Chovelon, Gabrielle; Trabelsi, Khouloud; Voltz, Marc

    2015-04-01

    Ditches are involved in the transfer of pesticide to surface and groundwaters (e.g. Louchart et al., 2001). Soil horizons underlying ditch beds may present specific soil characteristics compared to neighbouring field soils due to erosion/deposition processes, to the specific biological activities (rooting dynamic and animal habitat) in the ditches (e.g. Vaughan et al., 2008) and to management practices (burning, dredging, mowing,...). Moreover, in contrast to percolation processes in field soils that can be assumed to be mainly 1D vertical, those occurring in the ditch beds are by essence 2D or even 3D. Nevertheless, due to a lake of knowledge, these specific aspects of transfer within ditch beds are generally omitted for hydrological simulation at the catchment scale (Mottes et al., 2014). Accordingly, the aims of this study were i) to characterize subsurface solute transfer through ditch beds and ii) to determine equivalent hydraulic parameters of the ditch beds for use in catchment scale hydrological simulations. A complementary aim was to evaluate the error in predictions performed when percolation in ditches is assumed to be similar to that in the neighbouring field soil. First, bromide transfer experiments were performed on undisturbed soil column (15 cm long with a 15 cm inner-diameter), horizontally and vertically sampled within each soil horizon underlying a ditch bed and within the neighboring field. Columns were sampled at the Roujan catchment (Hérault, France), which belongs to the long term Mediterranean hydrological observatory OMERE (Voltz and Albergel, 2002). Second, for each column, a set of parameters was determined by inverse optimization with mobile-immobile or dual permeability models, with CXTFIT (Toride et al., 1999) or with HYDRUS (Simunek et al., 1998). Third, infiltration and percolation in the ditch was simulated by a 2D flow domain approach considering the 2D variation in hydraulic properties of the cross section of a ditch bed. Last

  9. High-resolution Digital Mapping of Historical Lava Flows as a Test-bed for Lava Flow Models

    Science.gov (United States)

    Pyle, D. M.; Parks, M.; Nomikou, P.; Mather, T. A.; Simou, E.; Kalnins, L. M.; Paulatto, M.; Watts, A. B.

    2013-12-01

    Quantitative analysis of high-resolution lava flow morphology can improve our understanding of past effusive eruptions by providing insight into eruptive processes and the rheological properties of erupted magmas. We report the results of an ongoing investigation into the young dacite lava flows of the Kameni islands, Santorini volcano, Greece, which were emplaced during both subaerial and shallow submarine eruptions over the past 3000 years. Historical eruptions of the Kameni islands since 1866 have been very carefully documented in contemporaneous scientific reports. Eruptions since 1573 appear to be time-predictable, with a close relationship between eruption length, the size of extruded lava domes, and the time elapsed since the previous eruption. A new NERC - Airborne Survey and Research Facility LiDAR survey of the Kameni islands was completed in May 2012, using a Leica ALS50 Airborne Laser Scanner mounted on a Dornier 228 aircraft. The topographic surface was mapped at an average point density of 2.1 points per square metre, and covers the entire extent of the youngest subaerial lava flow fields on Santorini. A 2-m DEM derived from the 2012 LiDAR dataset was merged with a 5-m resolution bathymetric grid, based on multibeam surveys carried out by the Hellenic Centre for Marine Research, during cruises in 2001 and 2006, using a SEABEAM 2120 hull-mounted swath system. The resultant grid provides the first high resolution map of both subaerial and submarine historic lava flows emplaced in the centre of the Santorini caldera, and includes several previously unidentified submarine flows and cones. Attribute maps were used to delineate and identify discrete lava flows both onshore and offshore; and morphometric profiles were used to compute accurate volumetric estimates for each of the historic flows, and to determine bulk rheological properties of the lavas, assuming a Bingham rheology. This ongoing work will improve our analysis of the relationship between

  10. Flow of power-law fluids in fixed beds of cylinders or spheres

    KAUST Repository

    Singh, John P.

    2012-10-29

    An ensemble average of the equations of motion for a Newtonian fluid over particle configurations in a dilute fixed bed of spheres or cylinders yields Brinkman\\'s equations of motion, where the disturbance velocity produced by a test particle is influenced by the Newtonian fluid stress and a body force representing the linear drag on the surrounding particles. We consider a similar analysis for a power-law fluid where the stress τ is related to the rate of strain e by τ = 2m en-1e, where m and n are constants. In this case, the ensemble-averaged momentum equation includes a body force resulting from the nonlinear drag exerted on the surrounding particles, a power-law stress associated with the disturbance velocity of the test particle, and a stress term that is linear with respect to the test particle\\'s disturbance velocity. The latter term results from the interaction of the test particle\\'s velocity disturbance with the random straining motions produced by the neighbouring particles and is important only in shear-thickening fluids where the velocity disturbances of the particles are long-ranged. The solutions to these equations using scaling analyses for dilute beds and numerical simulations using the finite element method are presented. We show that the drag force acting on a particle in a fixed bed can be written as a function of a particle-concentration-dependent length scale at which the fluid velocity disturbance produced by a particle is modified by hydrodynamic interactions with its neighbours. This is also true of the drag on a particle in a periodic array where the length scale is the lattice spacing. The effects of particle interactions on the drag in dilute arrays (periodic or random) of cylinders and spheres in shear-thickening fluids is dramatic, where it arrests the algebraic growth of the disturbance velocity with radial position when n≥ 1 for cylinders and n≥ 2 for spheres. For concentrated random arrays of particles, we adopt an

  11. Gas flow analysis in the sludge melting furnace with packed bed. Jutensogata gesui odei yoyuro ni okeru gas nagare no kaiseki

    Energy Technology Data Exchange (ETDEWEB)

    Wang, J.; Takahashi, R.; Yagi, J. (Tohoku Univ., Sendai (Japan). Research Inst. of Mineral Dressing and Metallurgy)

    1990-07-10

    Gas flow in a sludge melting furnace with packed bed was analyzed. As the fundamantal equation, Ergun equation with an inertial term was applied for gas flow in the packed bed and for gas flow in the freeboard of upper part of packed bed where multistage gas inlets located, turbulence model of kappa-epsilon model was applied. Two and three dimensional cold experimental equipments were prepared to measure gas flow rates and pressure distribution and to compared these results with the results of numerical simulation. The validity of theoretical model was verified from these results. It is necessary to add the inertial term to the Ergun equation at the point where gas flow line changes suddenly (discretization points). Further, when the freeboard was considered, the isobar could not be realized in some cases as the boundary condition at the top of the packed bed. In order to calculate the gas flow in a complex shape such as the sludge melting furnace, it is effective to apply the body fitted coordinate system having mesh generated along the boundary shape by solving the elliptic type equation and to carry out numerical analysis with the finite difference method. 13 refs., 8 figs., 1 tab.

  12. A field study of turbulent flows in shallow gravel-bed rivers

    OpenAIRE

    Franca, Mário Jorge Rodrigues Pereira da; Lemmin, Ulrich

    2007-01-01

    The study of turbulent flows has always been a challenge for scientists. Turbulent flows are common in nature and have an important role in several geophysical processes related to a variety of phenomena such as river morphology, landscape modeling, atmospheric dynamics and ocean currents. At present, new measurement and observation techniques suitable for fieldwork can be combined with laboratory and theoretical work in order to advance in the understanding of river processes. In this Ph.D. ...

  13. Quality indicators for woodwind reed material

    International Nuclear Information System (INIS)

    Glave, Stefan; Pallon, Jan; Bornman, Chris; Bjoern, Lars Olof; Wallen, Rita; Raastam, Jacob; Kristiansson, Per; Elfman, Mikael; Malmqvist, Klas

    1999-01-01

    For the generation of sound, some woodwind musical instruments, e.g. oboe, bassoon, clarinet and saxophone, are provided with mouthpieces made from reeds. These reeds are the culms of Arundo donax, a tall, cane-like perennial grass. A general problem is that the material is of varying quality, yet externally differences cannot be observed. Hence, large proportions of the prepared reeds are unusable. One hypothesis is that the changes in quality are correlated with differences in the chemical and anatomical structure of the tissue. Therefore, a comparison of superior and inferior mouthpieces, used by professional musicians, was undertaken to determinate potential indicators of quality. Nuclear microprobe analysis of reeds was carried out and complemented by scanning electron and light microscopy. The elemental levels of Si, P, S, Cl, K and Ca were compared between good and poor mouthpieces using appropriate statistical tests. No statistically significant differences could be identified. Microscopical observations showed that partial occlusion of vessels by tylose formation was associated with material deemed unusable

  14. Making a Joyful Noise: Teresa L. Reed

    Science.gov (United States)

    Hamilton, Kendra

    2005-01-01

    Teresa L. Reed knew as far back as she can remember that she'd be doing something in music. This document briefly describes her early years with music and her involvement with music today. She is a member of Higher Dimensions Choir, a teacher, and a writer of the book The Holy Profane: Religion in Black Popular Music. This document gives a brief…

  15. The Reed Elsevier stock price gap

    NARCIS (Netherlands)

    Kamp, B.

    1995-01-01

    This is the report of a limited study on the structural stock price differences between Reed and Elsevier. The purpose of this study is to provide an overview of the problem area and to formulate and discuss several hypotheses regarding the causes of this gap. The research was performed by

  16. Simulation of a cross-flow shrinking-bed reactor for the hydrolysis of lignocellulosics.

    Science.gov (United States)

    Converse, A O

    2002-01-01

    An idealized model is developed for the case in which biomass slurry is conveyed through an annulus, with water or steam entering through an inner porous wall and liquid product leaving through an outer porous wall. It is assumed that the ratio of occluded liquid to solid in the slurry is a constant, Rws, and that non-occluded water is immediately removed from the reactor. The goal of > 90% sugar yield with > 10% sugar in the product is almost reached (88% glucose yield, 91% xylose yield, 47 g/l glucose and 45 g/l xylose) at 240 degrees C, 1% acid. Rws = 1 and a radial wash water flow of three times the initial mass flow of solids to the reactor per meter of reactor length per g/l of sugar concentration in the occluded water. If Rws is limited to 3, the yield falls to 85% and the total sugar concentration to 61 g/l. Even without cross-flow wash, the yields can be increased by about 16 percentage points, compared to plug flow, by extracting excess liquid through the outer wall as it is formed. At 200 degrees C, where one might prefer to operate for ease of control and concern about the possibility of making fermentation inhibitors at higher temperatures, the maximum glucose yield in a plug-flow reactor is low (12-13%) whereas in a cross-flow reactor, at a high cross-flow wash rate, it can still be quite high (60-83%) but at a very low concentration (0.57-1.47%). In these simulations it is assumed that one-half of the inerts is solubilized. The formation of oligomers is neglected.

  17. Novel method for investigation and evaluation of heat transfer in fixed bed tubular reactors with gas flow

    Science.gov (United States)

    Bauer, M.; Adler, R.

    2002-08-01

    A novel concept for the investigation and evaluation of radial heat transfer in fixed bed tubular reactors in absence of a chemical reaction based on instationary measurements is presented in this work. Compared to known stationary investigational concepts one is able to get an increased informational yield from the experimental data especially for low tube-to-particle diameter ratios and small gas mass flow rates to be found typically in heterogeneous catalysis. The question discussed contrary in literature which boundary condition should be applied to the inner reactor wall is answered. A empirical correlation of the parameters for the two dimensional pseudohomogeneous model was found which allows a more accurate description of the experimental findings than known approaches from literature. The experiments were conducted for spherical particles and hollow cylinders made from steatite.

  18. Effects of solar collecting area and water flow rate on the performance of a sand bed solar collector

    International Nuclear Information System (INIS)

    Maganhar, A.L.; Memon, A.H.; Panhwar, M.I.

    2005-01-01

    The often discussed renewable sources of energy have been great interest to energy researchers and planners for quite some time. The primary of renewing all sources of energy is the sun. There have been two main problems not yet fully resolved. One is the large scale production of energy and other is the cost factor. In the present study, the cost factor is under consideration. In this regard a non-conventional solar collector using indigenous material (pit sand) as solar absorber is designed and manufactured. This paper presents the results of an investigation of the effect of solar collecting area and water flow rate on the performance of a pit sand bed solar collector especially in terms of rise in water temperature. Three pit sand solar collectors of area 1m/sup 2/ each were connected in series to enhance the collecting area and the system was tested for different flow rates. Experimental results proved that there was increase in water temperature with increase in solar collecting area an decreases in water temperature with increase in flow rate. (author)

  19. INFLUENCE OF RIVER BED ELEVATION SURVEY CONFIGURATIONS AND INTERPOLATION METHODS ON THE ACCURACY OF LIDAR DTM-BASED RIVER FLOW SIMULATIONS

    Directory of Open Access Journals (Sweden)

    J. R. Santillan

    2016-09-01

    Full Text Available In this paper, we investigated how survey configuration and the type of interpolation method can affect the accuracy of river flow simulations that utilize LIDAR DTM integrated with interpolated river bed as its main source of topographic information. Aside from determining the accuracy of the individually-generated river bed topographies, we also assessed the overall accuracy of the river flow simulations in terms of maximum flood depth and extent. Four survey configurations consisting of river bed elevation data points arranged as cross-section (XS, zig-zag (ZZ, river banks-centerline (RBCL, and river banks-centerline-zig-zag (RBCLZZ, and two interpolation methods (Inverse Distance-Weighted and Ordinary Kriging were considered. Major results show that the choice of survey configuration, rather than the interpolation method, has significant effect on the accuracy of interpolated river bed surfaces, and subsequently on the accuracy of river flow simulations. The RMSEs of the interpolated surfaces and the model results vary from one configuration to another, and depends on how each configuration evenly collects river bed elevation data points. The large RMSEs for the RBCL configuration and the low RMSEs for the XS configuration confirm that as the data points become evenly spaced and cover more portions of the river, the resulting interpolated surface and the river flow simulation where it was used also become more accurate. The XS configuration with Ordinary Kriging (OK as interpolation method provided the best river bed interpolation and river flow simulation results. The RBCL configuration, regardless of the interpolation algorithm used, resulted to least accurate river bed surfaces and simulation results. Based on the accuracy analysis, the use of XS configuration to collect river bed data points and applying the OK method to interpolate the river bed topography are the best methods to use to produce satisfactory river flow simulation outputs

  20. Hydrodynamic analysis of a three-fluidized bed reactor cold flow model for chemical looping hydrogen generation. Pressure characteristics

    Energy Technology Data Exchange (ETDEWEB)

    Xue, Zhipeng; Xiang, Wenguo; Chen, Shiyi; Wang, Dong [Southeast Univ., Nanjing (China). School of Energy and Environment

    2013-07-01

    Chemical looping hydrogen generation (CLHG) can produce pure hydrogen with inherent separation of CO{sub 2} from fossils fuel. The process involves a metal oxide, as an oxygen carrier, such as iron oxide. The CLHG system consists of three reactors: a fuel reactor (FR), a steam reactor (SR) and an air reactor (AR). In the FR, the fuel gases react with iron oxides (hematite Fe{sub 2}O{sub 3}, magnetite Fe{sub 3}O{sub 4}, wuestite FeO), generating reduced iron oxides (FeO or even Fe), and with full conversion of gaseous fuels, pure CO{sub 2} can be obtained after cooling the flue gas from the fuel reactor; in the SR, FeO and Fe reacts with steam to generate magnetite (Fe{sub 3}O{sub 4}) and H{sub 2}, the latter representing the final target product of the process; in the AR, the magnetite is oxidized back to hematite which is used in another cycle. A cold flow model of three-fluidized bed for CLHG corresponding to 50 KW hot units has been built. A major novelty of this facility is the compact fuel reactor, which integrates a bubble and a fast fluidized bed to avoid the incomplete conversion of the fuel gas caused by the thermodynamics equilibrium. In order to study the pressure characteristics and the solids concentration of the system, especially in the fuel reactor, the gas velocity of three reactors, gas flow of L-type value, total solids inventory (TSI) and the secondary air of fuel reactor were varied. Results show that the pressure and the solids concentration are strongly influenced by the fluidizing-gas velocity of three reactors. Moreover, the entrainment of the upper part of fuel reactor increases as the total solids inventory increases, and the operating range of the FR can be changed by introducing secondary air or increasing the total solids inventory.

  1. Real rock-microfluidic flow cell: A test bed for real-time in situ analysis of flow, transport, and reaction in a subsurface reactive transport environment.

    Science.gov (United States)

    Singh, Rajveer; Sivaguru, Mayandi; Fried, Glenn A; Fouke, Bruce W; Sanford, Robert A; Carrera, Martin; Werth, Charles J

    2017-09-01

    Physical, chemical, and biological interactions between groundwater and sedimentary rock directly control the fundamental subsurface properties such as porosity, permeability, and flow. This is true for a variety of subsurface scenarios, ranging from shallow groundwater aquifers to deeply buried hydrocarbon reservoirs. Microfluidic flow cells are now commonly being used to study these processes at the pore scale in simplified pore structures meant to mimic subsurface reservoirs. However, these micromodels are typically fabricated from glass, silicon, or polydimethylsiloxane (PDMS), and are therefore incapable of replicating the geochemical reactivity and complex three-dimensional pore networks present in subsurface lithologies. To address these limitations, we developed a new microfluidic experimental test bed, herein called the Real Rock-Microfluidic Flow Cell (RR-MFC). A porous 500μm-thick real rock sample of the Clair Group sandstone from a subsurface hydrocarbon reservoir of the North Sea was prepared and mounted inside a PDMS microfluidic channel, creating a dynamic flow-through experimental platform for real-time tracking of subsurface reactive transport. Transmitted and reflected microscopy, cathodoluminescence microscopy, Raman spectroscopy, and confocal laser microscopy techniques were used to (1) determine the mineralogy, geochemistry, and pore networks within the sandstone inserted in the RR-MFC, (2) analyze non-reactive tracer breakthrough in two- and (depth-limited) three-dimensions, and (3) characterize multiphase flow. The RR-MFC is the first microfluidic experimental platform that allows direct visualization of flow and transport in the pore space of a real subsurface reservoir rock sample, and holds potential to advance our understandings of reactive transport and other subsurface processes relevant to pollutant transport and cleanup in groundwater, as well as energy recovery. Copyright © 2017 Elsevier B.V. All rights reserved.

  2. Computational study of fluid flow and heat transfer in composite packed beds of spheres with low tube to particle diameter ratio

    International Nuclear Information System (INIS)

    Yang, Jian; Wu, Jiangquan; Zhou, Lang; Wang, Qiuwang

    2016-01-01

    Highlights: • Flow and heat transfer in composite packed beds with low d t /d pe are investigated. • The wall effect would be restrained with radially layered composite packing (RLM). • Heat flux and overall heat transfer efficiency can be improved with RLM packing. - Abstract: The effect of the tube wall on the fluid flow and heat transfer would be important in the packed bed with low tube to particle diameter ratio, which may lead to flow and temperature maldistributions inside, and the heat transfer performance may be lowered. In the present paper, the flow and heat transfer performances in both the composite and uniform packed beds of spheres with low tube to particle diameter were numerically investigated, where the composite packing means randomly packing with non-uniform spheres and the uniform packing means randomly packing with uniform spheres, including radially layered composite packing (RLM), axially layered composite packing (ALM), randomly composite packing (RCM) and randomly uniform packing (RPM). Both the composite and uniform packings were generated with discrete element method (DEM), and the influence of the wall effect on the flow and heat transfer in the packed beds were carefully studied and compared with each other. Firstly, it is found that, the wall effect on the velocity and temperature distributions in the randomly packed bed of uniform spheres (RPM) with low tube to particle diameter ratio were obvious. The average velocity of the near-tube-wall region is higher than that of the inner-tube region in the bed. When the tube wall is adiabatic, the average temperature of the near-tube-wall region is lower. With radially layered composite packing method (RLM), smaller pores would be formed close to the tube wall and big flow channels would be formed in the inner-tube region of the bed, which would be benefit to restrain the wall effect and improve heat transfer in the bed with low tube to particle diameter ratio. Furthermore, it is also

  3. Effect of hydraulic parameters on sediment transport capacity in overland flow over erodible beds

    NARCIS (Netherlands)

    Ali, M.; Sterk, G.; Seeger, K.M.; Boersema, M.P.; Peters, P.D.

    2012-01-01

    Sediment transport is an important component of the soil erosion process, which depends on several hydraulic parameters like unit discharge, mean flow velocity, and slope gradient. In most of the previous studies, the impact of these hydraulic parameters on transport capacity was studied for

  4. A study of dilute to dense flow in a circulating fluidized bed

    DEFF Research Database (Denmark)

    Ibsen, Claus Hübbe; Solberg, Tron; Hjertager, Bjørn H.

    2001-01-01

    This work concerns a experimental and numerical study on how the amount of particles influences the flow in the CFB. Experiments are performed with a 1D Laser and Phase doppler anemometry, whereby data of axial velocity, RMS velocity and particle diameter is obtained. The numerical simulations ar...

  5. Ventromedial prefrontal cortex damage alters resting blood flow to the bed nucleus of stria terminalis.

    Science.gov (United States)

    Motzkin, Julian C; Philippi, Carissa L; Oler, Jonathan A; Kalin, Ned H; Baskaya, Mustafa K; Koenigs, Michael

    2015-03-01

    The ventromedial prefrontal cortex (vmPFC) plays a key role in modulating emotional responses, yet the precise neural mechanisms underlying this function remain unclear. vmPFC interacts with a number of subcortical structures involved in affective processing, including the amygdala, hypothalamus, periaqueductal gray, ventral striatum, and bed nucleus of stria terminalis (BNST). While a previous study of non-human primates shows that vmPFC lesions reduce BNST activity and anxious behavior, no such causal evidence exists in humans. In this study, we used a novel application of magnetic resonance imaging (MRI) in neurosurgical patients with focal, bilateral vmPFC damage to determine whether vmPFC is indeed critical for modulating BNST function in humans. Relative to neurologically healthy subjects, who exhibited robust rest-state functional connectivity between vmPFC and BNST, the vmPFC lesion patients had significantly lower resting-state perfusion of the right BNST. No such perfusion differences were observed for the amygdala, striatum, hypothalamus, or periaqueductal gray. This study thus provides unique data on the relationship between vmPFC and BNST, suggesting that vmPFC serves to promote BNST activity in humans. This finding is relevant for neural circuitry models of mood and anxiety disorders. Copyright © 2014 Elsevier Ltd. All rights reserved.

  6. Estimation of particle velocity in moving beds based on a flow model for bulk solids. Ryudo model ni motozuita idoso no ryushi sokudo no suisan

    Energy Technology Data Exchange (ETDEWEB)

    Takahashi, H. (Muroran Inst. of Tech., Hokkaido (Japan)); Honda, Y. (Snow Brand Milk Products Co. Ltd., Sapporo (Japan))

    1992-11-10

    Based on a particle flow model (stress-shear strain velocity relational expression) which takes account of the bulk volume expansion effect during shearing deformation of particles, a new estimation method for particle velocity distribution and stress distribution is proposed. The method is applied to a crossflow moving bed and to a moving bed for comparison with the experimental values to examine its validity. The method is further extended to predict the velocity profile and stress profile of moving beds in a vertical tube (countercurrent and concurrent) accompanying gas flow. It is indicated that the bulk volume expansion effect differs according to dimensions. The velocity distribution and the stress distribution of flows in a vertical tube are greatly influenced by the nature of the flow, i.e. whether it is a counterflow or a concurrent flow, and the frictional force of solids on a wall surface increases markedly in a concurrent flow, which induces considerable lag of particle velocity. The parameter which is contained in the model and indicates the bulk volume expansion effect is a function of the particle velocity, and it is almost unaffected by the flow rate of gas moving. 7 refs., 10 figs.

  7. Wall-Roughness Effects on Flow and Scouring in Curved Channels with Gravel Beds

    OpenAIRE

    Hersberger, D.; Franca, Mário J.; Schleiss, Anton

    2016-01-01

    Due to a complex three-dimensional flow pattern, the outer banks of river bends are predisposed to erosion. When endangering civil structures, preventing measures to mitigate this erosion are thus required. Vertical ribs at protection walls for scour reduction have been applied to several flood protection projects in mountain rivers; nevertheless, no systematic and intensive study has been presented so far to evaluate their effect. This paper investigates experimentally the effect of vertical...

  8. Structural characterisation of pretreated solids from flow-through liquid hot water treatment of sugarcane bagasse in a fixed-bed reactor

    CSIR Research Space (South Africa)

    Reddy, P

    2015-05-01

    Full Text Available Untreated sugarcane bagasse and sugarcane bagasse pretreated with flow-through liquid hot water (LHW) treatment (170-207°C and 204-250 ml/min) in a fixed-bed reactor have been structurally characterised. Field emission gun scanning electron...

  9. The effect of bed roughness on the free surface of an open channel flow and implications for remotely monitoring river discharge

    Science.gov (United States)

    Johnson, Erika; Cowen, Edwin

    2013-11-01

    The effect of increased bed roughness on the free surface turbulence signature of an open channel flow is investigated with the goal of incorporating the findings into a methodology to remotely monitor volumetric flow rates. Half of a wide (B = 2 m) open channel bed is covered with a 3 cm thick layer of loose gravel (D50 = 0.6 cm). Surface PIV (particle image velocimetry) experiments are conducted for a range of flow depths (B/H = 10-30) and Reynolds numbers (ReH = 10,000-60,000). It is well established that bed roughness in wall-bounded flows enhances the vertical velocity fluctuations (e.g. Krogstad et al. 1992). When the vertical velocity fluctuations approach the free surface they are redistributed (e.g. Cowen et al. 1995) to the surface parallel component directions. It is anticipated and confirmed that the interaction of these two phenomena result in enhanced turbulence at the free surface. The effect of the rough bed on the integral length scales and the second order velocity structure functions calculated at the free surface are investigated. These findings have important implications for developing new technologies in stream gaging.

  10. Predicting bed shear stress and its role in sediment dynamics and restoration potential of the Everglades and other vegetated flow systems

    Science.gov (United States)

    Larsen, Laurel G.; Harvey, Judson; Crimaldi, John P.

    2009-01-01

    Entrainment of sediment by flowing water affects topography, habitat suitability, and nutrient cycling in vegetated floodplains and wetlands, impacting ecosystem evolution and the success of restoration projects. Nonetheless, restoration managers lack simple decision-support tools for predicting shear stresses and sediment redistribution potential in different vegetation communities. Using a field-validated numerical model, we developed state-space diagrams that provide these predictions over a range of water-surface slopes, depths, and associated velocities in Everglades ridge and slough vegetation communities. Diminished bed shear stresses and a consequent decrease in bed sediment redistribution are hypothesized causes of a recent reduction in the topographic and vegetation heterogeneity of this ecosystem. Results confirmed the inability of present-day flows to entrain bed sediment. Further, our diagrams showed bed shear stresses to be highly sensitive to emergent vegetation density and water-surface slope but less sensitive to water depth and periphyton or floating vegetation abundance. These findings suggested that instituting a pulsing flow regime could be the most effective means to restore sediment redistribution to the Everglades. However, pulsing flows will not be sufficient to erode sediment from sloughs with abundant spikerush, unless spikerush density first decreases by natural or managed processes. Our methods provide a novel tool for identifying restoration parameters and performance measures in many types of vegetated aquatic environments where sediment erosion and deposition are involved.

  11. Experimental investigation of pebble flow dynamics using radioactive particle tracking technique in a scaled-down Pebble Bed Modular Reactor (PBMR)

    Energy Technology Data Exchange (ETDEWEB)

    Khane, Vaibhav; Said, I.A.; Al-Dahhan, Muthanna H., E-mail: aldahhanm@mst.edu

    2016-06-15

    Highlights: • Pebble Flow fields at Pebble Bed Modular Reactor was investigated. • Radioactive Particle Tracking (RPT) technique has been used. • Plug flow type velocity profile is suggested at upper cylindrical region. - Abstract: The Pebble Bed Modular Reactor (PBMR) is a type of very-high-temperature reactor (VHTR) that is conceptually very similar to moving bed reactors used in the chemical and petrochemical industries. In a PBMR core, nuclear fuel is in the form of pebbles and moves slowly under the influence of gravity. In this work, an integrated experimental and computational study of granular flow in a scaled-down cold flow PBMR was performed. A continuous pebble re-circulation experimental set-up, mimicking the flow of pebbles in a PBMR was designed and developed. An experimental investigation of pebble flow dynamics in a scaled down test reactor was carried out using a non-invasive radioactive particle tracking (RPT) technique that used a cobalt-60 based tracer to mimic pebbles in terms of shape, size and density. A cross-correlation based position reconstruction algorithm and RPT calibration data were used to obtain results about Lagrangian trajectories, the velocity field, and residence time distributions. The RPT technique results a serve as a benchmark data for assessing contact force models used in the discrete element method (DEM) simulations.

  12. Experimental and Numerical Investigation of Four- Phase Flow (Water–Gasoline-Air-Solid in a Fluidized Bed Column

    Directory of Open Access Journals (Sweden)

    Riyadh S. Al-Turaihi

    2016-03-01

    Full Text Available In this paper four phase fluidized bed is experimentally built and numerically modeled to study the bed characteristics such as ratio (the static bed height of solid particle / the bed diameter (H/D, air, gasoline , and water superficial velocity. The test pipe for the experimental rig is Perspex pipe with 1 m long and 0.0254 m diameter. The 2D numerical model has been established with Ansys fluent 15.0. Pressure drop equation is found to relate the pressure drop with the bed parameters with deviation of 22%. The Four-phases was represented by air, water, gasoline and solid particle. The results show that the pressure of the bed increases as the ratio H/D increases and air, gasoline , and water superficial velocity increases. As well as the expansion of the bed increases as air, gasoline, and water superficial velocity increases.

  13. Linking the spatial distribution of bed load transport to morphological change during high-flow events in a shallow braided river

    Science.gov (United States)

    Williams, R. D.; Rennie, C. D.; Brasington, J.; Hicks, D. M.; Vericat, D.

    2015-03-01

    This paper provides novel observations linking the connections between spatially distributed bed load transport pathways, hydraulic patterns, and morphological change in a shallow, gravel bed braided river. These observations shed light on the mechanics of braiding processes and illustrate the potential to quantify coupled material fluxes using remotely sensed methods. The paper focuses upon a 300 m long segment of the Rees River, New Zealand, and utilizes spatially dense observations from a mobile acoustic Doppler current profiler (aDcp) to map depth, velocity, and channel topography through a sequence of high-flow events. Apparent bed load velocity is estimated from the bias in aDcp bottom tracking and mapped to indicate bed load transport pathways. Terrestrial laser scanning (TLS) of exposed bar surfaces is fused with the aDcp surveys to generate spatially continuous digital elevation models, which quantify morphological change through the sequence of events. Results map spatially distributed bed load pathways that were likely to link zones of erosion and deposition. The coherence between the channel thalweg, zone of maximum hydraulic forcing, and maximum apparent bed load pathways varied. This suggests that, in places, local sediment supply sources exerted a strong control on the distribution of bed load, distinct from hydraulic forcing. The principal braiding mechanisms observed were channel choking, leading to subsequent bifurcation. Results show the connection between sediment sources, pathways, and sinks and their influence on channel morphology and flow path directions. The methodology of coupling spatially dense aDcp surveys with TLS has considerable potential to understand connections between processes and morphological change in dynamic fluvial settings.

  14. Regional Energy Deployment System (ReEDS)

    Energy Technology Data Exchange (ETDEWEB)

    Short, W.; Sullivan, P.; Mai, T.; Mowers, M.; Uriarte, C.; Blair, N.; Heimiller, D.; Martinez, A.

    2011-12-01

    The Regional Energy Deployment System (ReEDS) is a deterministic optimization model of the deployment of electric power generation technologies and transmission infrastructure throughout the contiguous United States into the future. The model, developed by the National Renewable Energy Laboratory's Strategic Energy Analysis Center, is designed to analyze the critical energy issues in the electric sector, especially with respect to potential energy policies, such as clean energy and renewable energy standards or carbon restrictions. ReEDS provides a detailed treatment of electricity-generating and electrical storage technologies and specifically addresses a variety of issues related to renewable energy technologies, including accessibility and cost of transmission, regional quality of renewable resources, seasonal and diurnal generation profiles, variability of wind and solar power, and the influence of variability on the reliability of the electrical grid. ReEDS addresses these issues through a highly discretized regional structure, explicit statistical treatment of the variability in wind and solar output over time, and consideration of ancillary services' requirements and costs.

  15. The use of a rigid disc to protect exposed structures in wounds treated with negative pressure wound therapy: effects on wound bed pressure and microvascular blood flow.

    Science.gov (United States)

    Anesäter, Erik; Borgquist, Ola; Torbrand, Christian; Roupé, K Markus; Ingemansson, Richard; Lindstedt, Sandra; Malmsjö, Malin

    2012-01-01

    There are increasing reports of deaths and serious complications associated with the use of negative pressure wound therapy (NPWT). Bleeding may occur in patients when NPWT is applied to a wound with exposed blood vessels or vascular grafts, possibly due to mechanical deformation and hypoperfusion of the vessel walls. Recent evidence suggests that using a rigid barrier disc to protect underlying tissue can prevent this mechanical deformation. The aim of this study was to examine the effect of rigid discs on the tissue exposed to negative pressure with regard to tissue pressure and microvascular blood flow. Peripheral wounds were created on the backs of eight pigs. The pressure and microvascular blood flow in the wound bed were measured when NPWT was applied. The wound was filled with foam, and rigid discs of different designs were inserted between the wound bed and the foam. The discs were created with or without channels (to accommodate exposed sensitive structures such as blood vessels and nerves), perforations, or a porous dressing that covered the underside of the discs (to facilitate pressure transduction and fluid evacuation). When comparing the results for pressure transduction to the wound bed, no significant differences were found using different discs covered with dressing, whereas pressure transduction was lower with bare discs. Microvascular blood flow in the wound bed decreased by 49 ± 7% when NPWT was applied to control wounds. The reduction in blood flow was less in the presence of a protective disc (e.g., -6 ± 5% for a dressing-covered, perforated disc, p = 0.006). In conclusion, NPWT causes hypoperfusion of superficial tissue in the wound bed. The insertion of a rigid barrier counteracts this effect. The placement of a rigid disc over exposed blood vessels or nerves may protect these structures from rupture and damage. © 2012 by the Wound Healing Society.

  16. The vibrating reed frequency meter: digital investigation of an early cochlear model.

    Science.gov (United States)

    Bell, Andrew; Wit, Hero P

    2015-01-01

    The vibrating reed frequency meter, originally employed by Békésy and later by Wilson as a cochlear model, uses a set of tuned reeds to represent the cochlea's graded bank of resonant elements and an elastic band threaded between them to provide nearest-neighbour coupling. Here the system, constructed of 21 reeds progressively tuned from 45 to 55 Hz, is simulated numerically as an elastically coupled bank of passive harmonic oscillators driven simultaneously by an external sinusoidal force. To uncover more detail, simulations were extended to 201 oscillators covering the range 1-2 kHz. Calculations mirror the results reported by Wilson and show expected characteristics such as traveling waves, phase plateaus, and a response with a broad peak at a forcing frequency just above the natural frequency. The system also displays additional fine-grain features that resemble those which have only recently been recognised in the cochlea. Thus, detailed analysis brings to light a secondary peak beyond the main peak, a set of closely spaced low-amplitude ripples, rapid rotation of phase as the driving frequency is swept, frequency plateaus, clustering, and waxing and waning of impulse responses. Further investigation shows that each reed's vibrations are strongly localised, with small energy flow along the chain. The distinctive set of equally spaced ripples is an inherent feature which is found to be largely independent of boundary conditions. Although the vibrating reed model is functionally different to the standard transmission line, its cochlea-like properties make it an intriguing local oscillator model whose relevance to cochlear mechanics needs further investigation.

  17. Analysis of in situ water velocity distributions in the lowland river floodplain covered by grassland and reed marsh habitats - a case study of the bypass channel of Warta River (Western Poland

    Directory of Open Access Journals (Sweden)

    Laks Ireneusz

    2017-12-01

    Full Text Available The analysis of in situ measurements of velocity distribution in the floodplain of the lowland river has been carried out. The survey area was located on a bypass channel of the Warta River (West of Poland which is filled with water only in case of flood waves. The floodplain is covered by grassland and reed marsh habitats. The velocity measurements were performed with an acoustic Doppler current profiler (ADCP in a cross-section with a bed reinforced with concrete slabs. The measured velocities have reflected the differentiated impact of various vegetation types on the loss of water flow energy. The statistical analyses have proven a relationship between the local velocities and the type of plant communities.

  18. A collision model for grain-resolving simulations of flows over dense, mobile, polydisperse granular sediment beds

    Science.gov (United States)

    Biegert, Edward; Vowinckel, Bernhard; Meiburg, Eckart

    2017-07-01

    We present a collision model for phase-resolved Direct Numerical Simulations of sediment transport that couple the fluid and particles by the Immersed Boundary Method. Typically, a contact model for these types of simulations comprises a lubrication force for particles in close proximity to another solid object, a normal contact force to prevent particles from overlapping, and a tangential contact force to account for friction. Our model extends the work of previous authors to improve upon the time integration scheme to obtain consistent results for particle-wall collisions. Furthermore, we account for polydisperse spherical particles and introduce new criteria to account for enduring contact, which occurs in many sediment transport situations. This is done without using arbitrary values for physically-defined parameters and by maintaining the full momentum balance of a particle in enduring contact. We validate our model against several test cases for binary particle-wall collisions as well as the collective motion of a sediment bed sheared by a viscous flow, yielding satisfactory agreement with experimental data by various authors.

  19. Reduction of the suction losses through reed valves in hermetic reciprocating compressors using a magnet coil

    Science.gov (United States)

    Hopfgartner, J.; Posch, S.; Zuber, B.; Almbauer, R.; Krischan, K.; Stangl, S.

    2017-08-01

    Reed valves are widely used in hermetic reciprocating compressors and are responsible for a large part of the thermodynamic losses. Especially, the suction valve, which is opened nearly during the whole suction stroke, has a big potential for improvement. Usually, suction valves are opened only by vacuum created by the moving piston and should be closed before the compression stroke starts to avoid a reversed mass-flow through the valve. Therefore, the valves are prestressed, which results on the other hand in a higher flow resistance. In this work, a suction valve is investigated, which is not closed by the preload of the valve but by an electromagnetic coil located in the suction muffler neck. Shortly before the piston reaches its bottom dead centre, voltage is applied to the coil and a magnetic force is generated which pulls the valve shut. Thereby, the flow resistance through the valve can be reduced by changing the preload on the reed valve because it is no longer needed to close the valve. The investigation of this adapted valve and the electromagnetic coil is firstly done by numerical simulations including fluid structure interactions of the reed valves of a reciprocating compressor and secondly by experiments made on a calorimeter test bench.

  20. 77 FR 26321 - Reed College, Reed Research Nuclear Reactor, Renewed Facility Operating License No. R-112

    Science.gov (United States)

    2012-05-03

    ... Nuclear Reactor, Renewed Facility Operating License No. R-112 AGENCY: Nuclear Regulatory Commission... Commission (NRC or the Commission) has issued renewed Facility Operating License No. R- 112, held by Reed... License No. R-112 will expire 20 years from its date of issuance. The renewed facility operating license...

  1. The effect of temperature and flow rate on the clarification of the aqueous stevia-extract in a fixed-bed column with zeolites

    Directory of Open Access Journals (Sweden)

    Mantovaneli I. C. C.

    2004-01-01

    Full Text Available Stevia is being used as a sweetener due to its low calorific value and its taste, which is very similar to that of sucrose. After extraction from dried leaves, stevia extract is dark in colour so needs to be clarified for better acceptance by consumers. Adsorption is one of the most important processes in this clarification. In this work the clarification of extract stevia extract in fixed-bed columns with calcium zeolites was studied. Two temperatures (10ºC and 30ºC and six different flow rates (2, 5, 9, 12, 16 and 19 mL/min were studied. The results showed that the mass-transfer coeffcient increases with an increase in flow rate and the length of unused bed reaches a maximum at 9 mL/min for both temperatures. The fit of the Thomas model with the breakthrough data was not very good.

  2. Numerical investigation of flow and heat transfer in a novel configuration multi-tubular fixed bed reactor for propylene to acrolein process

    Science.gov (United States)

    Jiang, Bin; Hao, Li; Zhang, Luhong; Sun, Yongli; Xiao, Xiaoming

    2015-01-01

    In the present contribution, a numerical study of fluid flow and heat transfer performance in a pilot-scale multi-tubular fixed bed reactor for propylene to acrolein oxidation reaction is presented using computational fluid dynamics (CFD) method. Firstly, a two-dimensional CFD model is developed to simulate flow behaviors, catalytic oxidation reaction, heat and mass transfer adopting porous medium model on tube side to achieve the temperature distribution and investigate the effect of operation parameters on hot spot temperature. Secondly, based on the conclusions of tube-side, a novel configuration multi-tubular fixed-bed reactor comprising 790 tubes design with disk-and-doughnut baffles is proposed by comparing with segmental baffles reactor and their performance of fluid flow and heat transfer is analyzed to ensure the uniformity condition using molten salt as heat carrier medium on shell-side by three-dimensional CFD method. The results reveal that comprehensive performance of the reactor with disk-and-doughnut baffles is better than that of with segmental baffles. Finally, the effects of operating conditions to control the hot spots are investigated. The results show that the flow velocity range about 0.65 m/s is applicable and the co-current cooling system flow direction is better than counter-current flow to control the hottest temperature.

  3. Upgrated fuel from reed canary grass

    Energy Technology Data Exchange (ETDEWEB)

    Oravainen, H. [VTT Energy, Jyvaeskylae (Finland)

    1997-12-01

    Results described in this presentation are from a large EU-project - Development of a new crop production system based on delayed harvesting and system for its combined processing to chemical pulp and biofuel powder. This is a project to develop the use of Reed Canary Grass (Phalaris Arundinaceae) both for pulp industry and energy production. The main contractor of the project is Swedish University of Agricultural Sciences (coordinator), task coordinators are United Milling Systems A/S from Denmark, and Jaakko Poeyry Oy and VTT Energy from Finland In addition, there are partners from several countries participating in the project

  4. Can we predict the response of large sand bed rivers to changes in flow and sediment supply? The case of the Missouri River.

    Science.gov (United States)

    Viparelli, E.; Blum, M. D.

    2015-12-01

    In the past century engineering projects and changes in land use significantly modified the hydrology and the sediment supply of large sand bed rivers all over the world. Field studies documented the river responses to the imposed changes, which can be summarized as adjustments in channel geometry, slope, and/or characteristics of the bed material. Further, one-, two- and three-dimensional river morphodynamic models were used to predict the fluvial system response to the imposed changes at time scales ranging from few months up to several decades. Notwithstading this previous research effort, the spatial and temporal scales of river adjustment, as well as quantitative predictions of the river responses, are still a matter of debate due to the difficulties associated with the interpretation of limited field datasets and with the large scale sediment transport modeling. Here we present the preliminary results of a study of the Missouri River response to the construction of dams, i.e. reduction in flood flow and sediment supply. In particular, we first compare the numerical results of a one-dimensional model of river morphodynamics for large, low slope sand bed rivers with field data to validate the model. The validated model is then used to constrain the spatial and temporal scales of the river adjustment, i.e. bed degradation in the Missouri River case. In other words, our numerical work focuses on how the magnitude and speed of the wave of channel bed degradation changes in time and space for the Missouri River case and how these scales change for different values of the ratio between pre- and pos-dam flow rates, and pre- and post-dam sediment loads.

  5. Flow of a Bingham fluid in a porous bed under the action of a magnetic field: Application to magneto-hemorheology

    Directory of Open Access Journals (Sweden)

    J.C. Misra

    2017-06-01

    Full Text Available The study deals with an investigation of the flow of a Bingham plastic fluid in a porous bed under the action of an external magnetic field. Porosity of the bed has been described by considering Brinkman model. Both steady and pulsatile motion of this non-Newtonian fluid have been analysed. The governing equations are solved numerically by developing a suitable finite difference scheme. As an application of the theory in the field of magneto-hemorheology, the said physical variables have been computed by considering the values of the involved parameters for blood flow in a pathological state, when the system is under the action of an external magnetic field. The pathological state corresponds to a situation, where the lumen of an arterial segment has turned into a porous structure due to formation of blood clots. Numerical estimates are obtained for the velocity profile and volumetric flow rate of blood, as well as for the shear stress, in the case of blood flow in a diseased artery, both the velocity and volumetric flow rate diminish, as the strength of the external magnetic field is enhanced. The study further shows that blood velocity is maximum in the plug (core region. It decreases monotonically as the particles of blood travel towards the wall. The study also bears the potential of providing numerical estimates for many industrial fluids that follow Bingham plastic model, when the values of different parameters are chosen appropriately.

  6. On natural circulation in High Temperature Gas-Cooled Reactors and pebble bed reactors for different flow regimes and various coolant gases

    International Nuclear Information System (INIS)

    Melesed'Hospital, G.

    1983-01-01

    The use of CO 2 or N 2 (heavy gas) instead of helium during natural circulation leads to improved performance in both High Temperature Gas-Cooled Reactors (HTGR) and in Pebble Bed Reactors (PBR). For instance, the coolant temperature rise corresponding to a coolant pressure level and a rate of afterheat removal could be only 18% with CO 2 as compared to He, for laminar flow in HTGR; this value would be 40% in PBR. There is less difference between HTGR and PBR for turbulent flows; CO 2 is found to be always better than N 2 . These types of results derived from relationships between coolant properties, coolant flow, temperature rise, pressure, afterheat levels and core geometry, are obtained for HTGR and PBR for various flow regimes, both within the core and in the primary loop

  7. Design of measuring instrument with whole direct method for bed shear stress under two-dimensional water-flow co-action

    Science.gov (United States)

    Huang, Hai-long; Zuo, Qi-hua; Zhou, Yi-ren; Shen, Yu-sheng; Li, Lan-xi

    2016-12-01

    The present study aims at the design and making of measuring instrument of whole direct method for bed shear stress under two-dimensional water-flow co-action. The instrument combines the traditional strain gauge with a precise pressure gauge, and adopts the method directly measuring the difference between the lateral hydrodynamic pressure and different head pressures on both sides of the force plate. As a result, such an instrument solves a technical puzzle of the past strain gauge, i.e. the difficulty to set apart shear stress and lateral force. Static force test and sink test both prove that the instrument is precise, stable and applicable to the measurement of rough beds with different shear stresses.

  8. Development and Implementation of 3-D, High Speed Capacitance Tomography for Imaging Large-Scale, Cold-Flow Circulating Fluidized Bed

    Energy Technology Data Exchange (ETDEWEB)

    Marashdeh, Qussai [Tech4imaging LLC, Columbus, OH (United States)

    2013-02-01

    A detailed understanding of multiphase flow behavior inside a Circulating Fluidized Bed (CFB) requires a 3-D technique capable of visualizing the flow field in real-time. Electrical Capacitance Volume Tomography (ECVT) is a newly developed technique that can provide such measurements. The attractiveness of the technique is in its low profile sensors, fast imaging speed and scalability to different section sizes, low operating cost, and safety. Moreover, the flexibility of ECVT sensors enable them to be designed around virtually any geometry, rendering them suitable to be used for measurement of solid flows in exit regions of the CFB. Tech4Imaging LLC has worked under contract with the U.S. Department of Energy's National Energy Technology Laboratory (DOE NETL) to develop an ECVT system for cold flow visualization and install it on a 12 inch ID circulating fluidized bed. The objective of this project was to help advance multi-phase flow science through implementation of an ECVT system on a cold flow model at DOE NETL. This project has responded to multi-phase community and industry needs of developing a tool that can be used to develop flow models, validate computational fluid dynamics simulations, provide detailed real-time feedback of process variables, and provide a comprehensive understating of multi-phase flow behavior. In this project, a complete ECVT system was successfully developed after considering different potential electronics and sensor designs. The system was tested at various flow conditions and with different materials, yielding real-time images of flow interaction in a gas-solid flow system. The system was installed on a 12 inch ID CFB of the US Department of Energy, Morgantown Labs. Technical and economic assessment of Scale-up and Commercialization of ECVT was also conducted. Experiments conducted with larger sensors in conditions similar to industrial settings are very promising. ECVT has also the potential to be developed for imaging multi

  9. The vibrating reed frequency meter: digital investigation of an early cochlear model

    Directory of Open Access Journals (Sweden)

    Andrew Bell

    2015-10-01

    Full Text Available The vibrating reed frequency meter, originally employed by Békésy and later by Wilson as a cochlear model, uses a set of tuned reeds to represent the cochlea’s graded bank of resonant elements and an elastic band threaded between them to provide nearest-neighbour coupling. Here the system, constructed of 21 reeds progressively tuned from 45 to 55 Hz, is simulated numerically as an elastically coupled bank of passive harmonic oscillators driven simultaneously by an external sinusoidal force. To uncover more detail, simulations were extended to 201 oscillators covering the range 1–2 kHz. Calculations mirror the results reported by Wilson and show expected characteristics such as traveling waves, phase plateaus, and a response with a broad peak at a forcing frequency just above the natural frequency. The system also displays additional fine-grain features that resemble those which have only recently been recognised in the cochlea. Thus, detailed analysis brings to light a secondary peak beyond the main peak, a set of closely spaced low-amplitude ripples, rapid rotation of phase as the driving frequency is swept, frequency plateaus, clustering, and waxing and waning of impulse responses. Further investigation shows that each reed’s vibrations are strongly localised, with small energy flow along the chain. The distinctive set of equally spaced ripples is an inherent feature which is found to be largely independent of boundary conditions. Although the vibrating reed model is functionally different to the standard transmission line, its cochlea-like properties make it an intriguing local oscillator model whose relevance to cochlear mechanics needs further investigation.

  10. Flow regulation in the Swiss Alps: a river network modelling approach to investigate the impacts on bed load and grain size distribution

    Science.gov (United States)

    Costa, A.; Molnar, P.; Schmitt, R. J. P.

    2017-12-01

    The grain size distribution (GSD) of river bed sediment results from the long term balance between transport capacity and sediment supply. Changes in climate and human activities may alter the spatial distribution of transport capacity and sediment supply along channels and hence impact local bedload transport and GSD. The effects of changed flow are not easily inferable due the non-linear, threshold-based nature of the relation between discharge and sediment mobilization, and the network-scale control on local sediment supply. We present a network-scale model for fractional sediment transport to quantify the impact of hydropower (HP) operations on river network GSD. We represent the river network as a series of connected links for which we extract the geometric characteristics from satellite images and a digital elevation model. We assign surface roughness based on the channel bed GSD. Bed shear stress is estimated at link-scale under the assumptions of rectangular prismatic cross sections and normal flow. The mass balance between sediment supply and transport capacity, computed with the Wilcock and Crowe model, determines transport rates of multiple grain size classes and the resulting GSD. We apply the model to the upper Rhone basin, a large Alpine basin in Switzerland. Since 1960s, changed flow conditions due to HP operations and sediment storage behind dams have potentially altered the sediment transport of the basin. However, little is known on the magnitude and spatial distribution of these changes. We force the model with time series of daily discharge derived with a spatially distributed hydrological model for pre and post HP scenarios. We initialize GSD under the assumption that coarse grains (d90) are mobilized only during mean annual maximum flows, and on the basis of ratios between d90 and characteristic diameters estimated from field measurements. Results show that effects of flow regulation vary significantly in space and in time and are grain size

  11. The thick-bedded tail of turbidite thickness distribution as a proxy for flow confinement: Examples from tertiary basins of central and northern Apennines (Italy)

    Science.gov (United States)

    Marini, Mattia; Felletti, Fabrizio; Milli, Salvatore; Patacci, Marco

    2016-07-01

    This study reviews the thickness statistics of non-channelized turbidites from four tertiary basins of Central-Northern Apennines (Italy), where bed geometry and sedimentary character have been previously assessed. Though very different in terms of size and, arguably, character of feeder system, these basins share a common stratigraphic evolution consisting in transition from an early ponded to a late unconfined setting of deposition. Based on comparison of thickness subsets from diverse locations and stratigraphic heights within the studied turbidite fills, this paper seeks to answer the following questions: i) how data collection procedures and field operational constraints (e.g. measure location, outcrop quality, use of thicknesses data from single vs. multiple correlative sections, stratigraphic thickness of the study interval) can affect statistics of sample data? ii) how depositional controls of confined vs. unconfined turbidite basins can result in different thickness-frequency distributions?; and iii) is there in thickness statistics a 'flow confinement' signature which can be used to distinguish between confined and unconfined turbidites? Results suggest that: i) best practices of data collection are crucial to a meaningful interpretation of sample data statistics, especially in presence of stratigraphic and spatial trends of turbidite bed thickness; ii) a systematic bias against cm-thick Tcd Bouma sequence turbidites exists in sample data, which can result in the low-end tail of empirical thickness-frequency distributions to depart significantly from the actual distribution of turbidite thickness; and iii) thickness statistics of beds starting with a basal Ta/Tb Bouma division bear a coherent relationship to the transition from ponded to unconfined depositional settings, consisting in reduction of variance and mean and, consequently, parameters, or even type, of best fit model distribution. This research highlights the role of flow stripping, sediment by

  12. Performance of staged and non-staged up-flow anaerobic sludge bed (USSB and UASB) reactors treating low strength complex wastewater.

    Science.gov (United States)

    Sevilla-Espinosa, Susana; Solórzano-Campo, Maricela; Bello-Mendoza, Ricardo

    2010-09-01

    The use of anaerobic processes to treat low-strength wastewater has been increasing in recent years due to their favourable performance-costs balance. For optimal results, it is necessary to identify reactor configurations that are best suited for this kind of application. This paper reports on the comparative study carried out with two high-rate anaerobic reactor systems with the objective of evaluating their performances when used for the treatment of low-strength, complex wastewater. One of the systems is the commonly used up-flow anaerobic sludge blanket (UASB) reactor. The other is the up-flow staged sludge bed (USSB) system in which the reactor was divided longitudinally into 3, 5 and 7 compartments by the use of baffles. The reactors (9 l) were fed with a synthetic, soluble and colloidal waste (chemical oxygen demand (COD) flow hydraulics, between plug-flow and completely-mixed, in the UASB and 7 stages USSB reactors allowed efficient degradation of substrates with minimum effluent concentrations. Low number of compartments in the USSB reactors increased the levels of short-circuiting thus reducing substrate removal efficiencies. All reactors showed high COD removal efficiencies (93-98%) and thus can be regarded as suitable for the treatment of low strength, complex wastewater. Staged anaerobic reactors can be a good alternative for this kind of application provided they are fitted with a large enough (> or =7) number of compartments to fully take advantage of their strengths. Scale factors seem to have influenced importantly on the comparison between one and multi staged sludge-bed reactors and, therefore, observations made here could change at larger reactor volumes.

  13. Simulation of groundwater flow, effects of artificial recharge, and storage volume changes in the Equus Beds aquifer near the city of Wichita, Kansas well field, 1935–2008

    Science.gov (United States)

    Kelly, Brian P.; Pickett, Linda L.; Hansen, Cristi V.; Ziegler, Andrew C.

    2013-01-01

    The Equus Beds aquifer is a primary water-supply source for Wichita, Kansas and the surrounding area because of shallow depth to water, large saturated thickness, and generally good water quality. Substantial water-level declines in the Equus Beds aquifer have resulted from pumping groundwater for agricultural and municipal needs, as well as periodic drought conditions. In March 2006, the city of Wichita began construction of the Equus Beds Aquifer Storage and Recovery project to store and later recover groundwater, and to form a hydraulic barrier to the known chloride-brine plume near Burrton, Kansas. In October 2009, the U.S. Geological Survey, in cooperation with the city of Wichita, began a study to determine groundwater flow in the area of the Wichita well field, and chloride transport from the Arkansas River and Burrton oilfield to the Wichita well field. Groundwater flow was simulated for the Equus Beds aquifer using the three-dimensional finite-difference groundwater-flow model MODFLOW-2000. The model simulates steady-state and transient conditions. The groundwater-flow model was calibrated by adjusting model input data and model geometry until model results matched field observations within an acceptable level of accuracy. The root mean square (RMS) error for water-level observations for the steady-state calibration simulation is 9.82 feet. The ratio of the RMS error to the total head loss in the model area is 0.049 and the mean error for water-level observations is 3.86 feet. The difference between flow into the model and flow out of the model across all model boundaries is -0.08 percent of total flow for the steady-state calibration. The RMS error for water-level observations for the transient calibration simulation is 2.48 feet, the ratio of the RMS error to the total head loss in the model area is 0.0124, and the mean error for water-level observations is 0.03 feet. The RMS error calculated for observed and simulated base flow gains or losses for the

  14. Diagenesis and Fluid Flow Variability of Structural Heterogeneity Units in Tight Sandstone Carrier Beds of Dibei, Eastern Kuqa Depression

    Directory of Open Access Journals (Sweden)

    H. Shi

    2017-01-01

    Full Text Available Tight sand gas plays an important role in the supply of natural gas production. It has significance for predicting sweet spots to recognize the characteristics and forming of heterogeneity in tight sandstone carrier beds. Heterogeneity responsible for spatial structure, such as the combination and distribution of relatively homogeneous rock layers, is basically established by deposition and eodiagenesis that collectively affect the mesogenesis. We have investigated the structural heterogeneity units by petrofacies in tight sandstone carrier beds of Dibei, eastern Kuqa Depression, according to core, logging, and micropetrology. There are four types of main petrofacies, that is, tight compacted, tight carbonate-cemented, gas-bearing, and water-bearing sandstones. The brine-rock-hydrocarbon diagenesis changes of different heterogeneity structural units have been determined according to the pore bitumen, hydrocarbon inclusions, and quantitative grain fluorescence. Ductile grains or eogenetic calcite cements destroy the reservoir quality of tight compacted or tight carbonate-cemented sandstones. Rigid grains can resist mechanical compaction and oil emplacement before gas charging can inhibit diagenesis to preserve reservoir property of other sandstones. We propose that there is an inheritance relationship between the late gas and early oil migration pathways, which implies that the sweet spots develop in the reservoirs that experienced early oil emplacement.

  15. Upgraded fuel from reed canary grass

    Energy Technology Data Exchange (ETDEWEB)

    Heiskanen, V.P.

    1995-12-31

    The feasibility of RCG for commercial utilization depends primarily on its applicability for pulp production and its use in energy production will be based on the residue that will be available after extracting the pulp fraction of the RCG. Roughly 20 ..30% of the material will be available for energy production purposes. However, the percentage may be higher/lower depending on the quality standards of the pulp fiber material. The harvesting period has a significant effect on the fuel characteristics of RCG. For instance the contents of N, S, Cl, K are clearly lower if the RCG is harvested in the spring (delayed) instead of summer/autumn. These elements affect significantly overall emission formation and ash behaviour and its melting temperature. The combustion related research in this project has been focused on the spring-harvested RCG. The project aims to evaluate the feasibility of delayed harvested RCG for energy production. In order to reach this goal, the following combustion methods will be tested and studied: combustion of pelletized RCG; gasification; combustion of pulverized RCG. In addition, pelletizing, reactivity and NO conversion of pulverized RCG will be studied. The research described here is a part of `Reed Canary Grass` project (in AIR programme). The contractors of the project are Swedish University of Agricultural Sciences (coordinator), United Milling Systems from Denmark, Jaakko Poeyry Oy and VTT Energy. In addition, there are partners from several countries participating in the project. The project has been divided in five tasks, VTT Energy being responsible for combustion related task `Upgraded fuel` that includes the research topics discussed in this paper

  16. A Three-Dimensional Numerical Study of Gas-Particle Flow and Chemical Reactions in Circulating Fluidised Bed Reactors

    DEFF Research Database (Denmark)

    Hansen, Kim Granly

    axial velocity, and pressure drop provided as a blind test in connection with the 10th International Workshop on Two-Phase Flow Prediction held in Merseburg, Germany, 2002. The simulated profiles are in good qualitative agreement with the experiments, but the extend of the radial solid segregation...... to a blind-test in connection to the 10th international workshop on two-phase flow prediction held in Merseburg, Germany, 2002. The results are validated against experimental findings of particle mass flux across the riser and pressure profile along the riser. The calculations show good agreement...... of the particulate phase is modeled using the kinetic theory for granular flow, and the gas phase turbulence is modeled using a Sub-Grid-Scale model. A computational study of a cold flowing CFB riser has been performed. The results have been compared to experimental findings of particle volume fraction, particle...

  17. Measurement and modelling of bed shear induced by solitary waves

    Digital Repository Service at National Institute of Oceanography (India)

    JayaKumar, S.

    horizontal continental shelf. Measurements of bed shear stress, surface elevation and flow velocities were carried out. Periodic waves were also generated and the bed shear stresses measured over a horizontal bed were found to be comparable with the earlier...

  18. Turning the tide: comparison of tidal flow by periodic sea level fluctuation and by periodic bed tilting in scaled landscape experiments of estuaries

    Science.gov (United States)

    Kleinhans, Maarten G.; van der Vegt, Maarten; Leuven, Jasper; Braat, Lisanne; Markies, Henk; Simmelink, Arjan; Roosendaal, Chris; van Eijk, Arjan; Vrijbergen, Paul; van Maarseveen, Marcel

    2017-11-01

    Analogue models or scale experiments of estuaries and short tidal basins are notoriously difficult to create in the laboratory because of the difficulty to obtain currents strong enough to transport sand. Our recently discovered method to drive tidal currents by periodically tilting the entire flume leads to intense sediment transport in both the ebb and flood phase, causing dynamic channel and shoal patterns. However, it remains unclear whether tilting produces periodic flows with characteristic tidal properties that are sufficiently similar to those in nature for the purpose of landscape experiments. Moreover, it is not well understood why the flows driven by periodic sea level fluctuation, as in nature, are not sufficient for morphodynamic experiments. Here we compare for the first time the tidal currents driven by sea level fluctuations and by tilting. Experiments were run in a 20 × 3 m straight flume, the Metronome, for a range of tilting periods and with one or two boundaries open at constant head with free inflow and outflow. Also, experiments were run with flow driven by periodic sea level fluctuations. We recorded surface flow velocity along the flume with particle imaging velocimetry and measured water levels along the flume. We compared the results to a one-dimensional model with shallow flow equations for a rough bed, which was tested on the experiments and applied to a range of length scales bridging small experiments and large estuaries. We found that the Reynolds method results in negligible flows along the flume except for the first few metres, whereas flume tilting results in nearly uniform reversing flow velocities along the entire flume that are strong enough to move sand. Furthermore, tidal excursion length relative to basin length and the dominance of friction over inertia is similar in tidal experiments and reality. The sediment mobility converges between the Reynolds method and tilting for flumes hundreds of metres long, which is impractical

  19. The Clarinet Reed: AN Introduction to its Biology, Chemistry, and Physics

    Science.gov (United States)

    Casadonte, Donald Jay

    Although clarinet reeds have been used for over two-hundred years, there has been little scientific study of the reed, either from a material science or engineering perspective. This document is intended to be the first large-scale study of the clarinet reed covering its biology, chemistry and physics. The reed is made, most often, from cane--Arundo donax. We present a complete atlas of the anatomy of Arundo donax, and examine the role of each of the cellular components in the clarinet reed performance. We examine the three principal chemical components of the processed clarinet reed: cellulose, xylan, and lignin through the use of instrumental analysis. We examine the breakdown pathways of the clarinet reed, and isolate five: (1) decrystallization of the cellulose microstructure, (2) removal of xylan by saliva, (3) plasticization of the reed material due to alkalai attack in saliva, (4) the culturing of a bacterium, Staph Epidermitis, in the cell wall matrix, (5) density changes due to salival coating of the reed. The physics of the reed is examined, and a finite element model of the modal shapes is presented. We present a theoretical treatment of the two modes of excitation of the reed, a low frequency mode (normal playing mode) due to vortex shedding, and a high frequency mode which is associated with reed squeak.

  20. Variability of Bed Drag on Cohesive Beds under Wave Action

    Directory of Open Access Journals (Sweden)

    Ilgar Safak

    2016-04-01

    Full Text Available Drag force at the bed acting on water flow is a major control on water circulation and sediment transport. Bed drag has been thoroughly studied in sandy waters, but less so in muddy coastal waters. The variation of bed drag on a muddy shelf is investigated here using field observations of currents, waves, and sediment concentration collected during moderate wind and wave events. To estimate bottom shear stress and the bed drag coefficient, an indirect empirical method of logarithmic fitting to current velocity profiles (log-law, a bottom boundary layer model for combined wave-current flow, and a direct method that uses turbulent fluctuations of velocity are used. The overestimation by the log-law is significantly reduced by taking turbulence suppression due to sediment-induced stratification into account. The best agreement between the model and the direct estimates is obtained by using a hydraulic roughness of 10 - 4 m in the model. Direct estimate of bed drag on the muddy bed is found to have a decreasing trend with increasing current speed, and is estimated to be around 0.0025 in conditions where wave-induced flow is relatively weak. Bed drag shows an increase (up to fourfold with increasing wave energy. These findings can be used to test the bed drag parameterizations in hydrodynamic and sediment transport models and the skills of these models in predicting flows in muddy environments.

  1. Prediction of bed level variations in nonuniform sediment bed channel

    Indian Academy of Sciences (India)

    B R Andharia

    2018-04-12

    Apr 12, 2018 ... have been undertaken for measurements of bed and water levels in an aggrading channel due to overloading of nonuniform sediments ..... 2.4 Thickness of active bed layer. The mixing zone of sediment remaining in contact with the flow is referred as active layer (ABL). The thickness and particle size ...

  2. Variability of bed drag on cohesive beds under wave action

    Science.gov (United States)

    Safak, Ilgar

    2016-01-01

    Drag force at the bed acting on water flow is a major control on water circulation and sediment transport. Bed drag has been thoroughly studied in sandy waters, but less so in muddy coastal waters. The variation of bed drag on a muddy shelf is investigated here using field observations of currents, waves, and sediment concentration collected during moderate wind and wave events. To estimate bottom shear stress and the bed drag coefficient, an indirect empirical method of logarithmic fitting to current velocity profiles (log-law), a bottom boundary layer model for combined wave-current flow, and a direct method that uses turbulent fluctuations of velocity are used. The overestimation by the log-law is significantly reduced by taking turbulence suppression due to sediment-induced stratification into account. The best agreement between the model and the direct estimates is obtained by using a hydraulic roughness of 10 -4">−4 m in the model. Direct estimate of bed drag on the muddy bed is found to have a decreasing trend with increasing current speed, and is estimated to be around 0.0025 in conditions where wave-induced flow is relatively weak. Bed drag shows an increase (up to fourfold) with increasing wave energy. These findings can be used to test the bed drag parameterizations in hydrodynamic and sediment transport models and the skills of these models in predicting flows in muddy environments.

  3. Study on effective particle diameters and coolability of particulate beds packed with irregular multi-size particles

    International Nuclear Information System (INIS)

    Thakre, S.; Ma, W.; Kudinov, P.; Bechta, S.

    2013-08-01

    One of the key questions in severe accident research is the coolability of the debris bed, i.e., whether decay heat can be completely removed by the coolant flow into the debris bed. Extensive experimental and analytical work has been done to substantiate the coolability research. Most of the available experimental data is related to the beds packed with single size (mostly spherical) particles, and less data is available for multi-size/irregular-shape particles. There are several analytical models available, which rely on the mean particle diameter and porosity of the bed in their predictions. Two different types of particles were used to investigate coolability of particulate beds at VTT, Finland. The first type is irregular-shape Aluminum Oxide gravel particles whose sizes vary from 0.25 mm to 10 mm, which were employed in the STYX experiment programme (2001-2008). The second type is spherical beads of Zirconium silicate whose sizes vary between 0.8 mm to 1 mm, which were used in the COOLOCE tests (Takasuo et al., 2012) to study the effect of multi-dimensional flooding on coolability. In the present work, the two types of particles are used in the POMECO-FL and POMECO-HT test facility to obtain their effective particle diameters and dryout heat flux of the beds, respectively. The main idea is to check how the heaters' orientations (vertical in COOLOCE vs. horizontal in POMECO-HT) and diameters (6 mm in COOLOCE vs. 3 mm in POMECO-HT) affect the coolability (dryout heat flux) of the test beds. The tests carried out on the POMECO-FL facility using a bed packed with aluminum oxide gravel particles show the effective particle diameter of the gravel particles is 0.65 mm, by which the frictional pressure gradient can be predicted by the Ergun equation. After the water superficial velocity is higher than 0.0025 m/s, the pressure gradient is underestimated. The effective particle diameter of the zirconium particles is found as 0.8 mm. The dryout heat flux is measured on

  4. Effect of Bed Depth on Granular Flow and Homogenization in a Vertical Bladed Mixer via Discrete Element Method

    Czech Academy of Sciences Publication Activity Database

    Barczi, T.; Trávníčková, Tereza; Havlica, Jaromír; Kohout, M.

    2015-01-01

    Roč. 38, č. 7 (2015), s. 1195-1202 ISSN 0930-7516 R&D Projects: GA ČR(CZ) GAP105/12/0664 Institutional support: RVO:67985858 Keywords : granular mixing * DEM * flow patterns Subject RIV: CI - Industrial Chemistry, Chemical Engineering Impact factor: 2.385, year: 2015

  5. CFD simulation of a coolant flow and a heat transfer in a pebble bed reactor - HTR2008-58334

    International Nuclear Information System (INIS)

    In, W. K.; Lee, W. J.; Hassan, Y. A.

    2008-01-01

    This CFD study is to simulate a coolant(gas) flow and heat transfer in a PBR core during a normal operation. This study used a pebble array with direct area contacts among the pebbles which is one of the pebbles arrangements for a detailed simulation of PBR core CFD studies. A CFD model is developed to more adequately represent the pebbles randomly stacked in the PBR core. The CFD predictions showed a large variation of the temperature on the pebble surface as well as in the pebble core. The temperature drop in the outer graphite layer is smaller than that in the pebble-core region. This is because the thermal conductivity of graphite is higher than the fuel (UO, mixture) conductivity in the pebble core. Higher pebble surface temperature is predicted downstream of the pebble contact due to a reverse flow. Multiple vortices are predicted to occur downstream of the spherical pebbles due to a flow separation. The coolant flow structure and fuel temperature in the PBR core appears to largely depend on the in-core distribution of the pebbles. (authors)

  6. Elementary analysis on the bed-sediment entrainment by debris flow and its application using the TopFlowDF model

    Directory of Open Access Journals (Sweden)

    Zheng Han

    2016-03-01

    Full Text Available The Geographic Information System (GIS-based TopFlowDF model is an effective simulation tool to analyse the debris-flow propagation on the fan. It has been validated in the previous research works and shows a satisfactory accuracy. We review the framework of the model in this paper and discuss that the simulation results are rather sensitive to the input conditions (e.g. the user-defined start point and debris-flow volume. In fact, previous studies have elucidated that sediment entrainment by debris flow conspicuously influences these input conditions. In this paper, we develop an elementary static approach with a three-layer model to estimate the entrainment and determine the amplification of total mass volume and peak discharge. Subsequently a new concept of “critical line” is proposed to detect the erodible reaches in the channel. Two cases in Japan and Norway are selected to illustrate the approach; analytical results show a good agreement with the in situ survey. The presented approach can provide a better solution to the input conditions as required by TopFlowDF model.

  7. Model-Based Optimization of Scaffold Geometry and Operating Conditions of Radial Flow Packed-Bed Bioreactors for Therapeutic Applications

    Directory of Open Access Journals (Sweden)

    Danilo Donato

    2014-01-01

    Full Text Available Radial flow perfusion of cell-seeded hollow cylindrical porous scaffolds may overcome the transport limitations of pure diffusion and direct axial perfusion in the realization of bioengineered substitutes of failing or missing tissues. Little has been reported on the optimization criteria of such bioreactors. A steady-state model was developed, combining convective and dispersive transport of dissolved oxygen with Michaelis-Menten cellular consumption kinetics. Dimensional analysis was used to combine more effectively geometric and operational variables in the dimensionless groups determining bioreactor performance. The effectiveness of cell oxygenation was expressed in terms of non-hypoxic fractional construct volume. The model permits the optimization of the geometry of hollow cylindrical constructs, and direction and magnitude of perfusion flow, to ensure cell oxygenation and culture at controlled oxygen concentration profiles. This may help engineer tissues suitable for therapeutic and drug screening purposes.

  8. Investigations into the coupled fluid flow and mechanical creep closure behavior of waste disposal rooms in bedded salt

    International Nuclear Information System (INIS)

    Mendenhall, F.T.; Butcher, B.M.; Davies, P.B.

    1991-01-01

    This paper presents the results of numerical simulations of a Waste Isolation Pilot Plant (WIPP) disposal room. In particular the results show: (1) that an initially empty disposal room will consolidate in 195 years to less than 10% of is initial volume, (2) that if waste, backfill, and gas generation are allowed to generate backstress, room consolidation ceases at about 9--10 MPa backstress and room expansion can occur with backstress slightly higher than 9--10 MPa, (3) that reducing the gas generation potentials and rates by a factor of five, drops the maximum room pressure from about 22 MPa to about 18 MPa and decreases the minimum room porosity from about 0.30 to 0.09, (4) that for two-phase fluid flow, brine and gas are driven out of the disposal room into the nonhalite interbeds and that pressures build in these interbeds near the disposal room, and (5) that the interbed pressurization shown in the two-phase flow can exceed lithostatic pressure of 14.8 MPa, which has the potential of opening preexisting fractures between disposal rooms in about 270 years. This work demonstrates the complex interdependent interactions of creep closure affecting void volume, gas pressurization, brine flow, gas generation, and interbed fracture dilation. Finally, work aiming at achieving greater coupling in the simulations of WIPP disposal rooms is discussed

  9. Designing selection criteria for reed canarygrass as a bioenergy feedstock

    Science.gov (United States)

    Reed canarygrass (Phalaris arundinacea L.) is a perennial C3 grass with a circumglobal distribution in the northern hemisphere and adaptation to a wide range of environmental conditions. This species is currently under development as a bioenergy feedstock in both North America and Europe. Thus, the ...

  10. Longer is fatter: body mass changes of migrant Reed Warblers ...

    African Journals Online (AJOL)

    Ecological barriers are the riskiest phases of the annual migrations for migratory birds. Comparatively little field data exists pertaining to the ability of migratory birds to prepare for the challenges of crossing ecological barriers, or their ability to recuperate afterward. Migrating Reed Warblers (Acrocephalus scirpaceus) were ...

  11. Graph Codes with Reed-Solomon Component Codes

    DEFF Research Database (Denmark)

    Høholdt, Tom; Justesen, Jørn

    2006-01-01

    We treat a specific case of codes based on bipartite expander graphs coming from finite geometries. The code symbols are associated with the branches and the symbols connected to a given node are restricted to be codewords in a Reed-Solomon code. We give results on the parameters of the codes...

  12. Project Re-ED: From Demonstration Project to Nationwide Program.

    Science.gov (United States)

    Hobbs, Nicholas

    1983-01-01

    Project Re-ED, an educational program for emotionally disturbed children started at Vanderbilt University's George Peabody College, relies on educational, psychological, and ecological strategies to help troubled children, rather than traditional therapy. The program employs teacher-counselors, who have direct contact with children, and emphasizes…

  13. Reeds as indicators of nutrient enrichment in a small temporarily ...

    African Journals Online (AJOL)

    Nutrient (NH4 and SRP) concentrations decreased from the bank towards the main estuary channel, suggesting that nutrients introduced into the estuary in groundwater and surface runoff were taken up by the fringe of reeds. The roots, rhizomes, stems and leaves of Phragmites at the site with the greatest Phragmites ...

  14. Colour patterning in the skin of the reed-frog

    African Journals Online (AJOL)

    1985-12-08

    Dec 8, 1985 ... A collec1ion 01 37 Natal reed·frogs, HyperoJius marmoratus, from a single locality was studied for their dorsal colour pattems. Data were assembled on the spectrophotometry, the structure and distribution of ttie chromato· phores by means of light and electron microscopy, and the features of colour ...

  15. Disrupting the Education Monopoly: A Conversation with Reed Hastings

    Science.gov (United States)

    Jacobs, Joanne

    2015-01-01

    This article features an interview with Netflix CEO, Reed Hastings. In this interview, Hastings relates that he told the "Wall Street Journal" in 2008 that he started looking at education--trying to figure out why our education is lagging when our technology is increasing at great rates and there's great innovation in so many other areas…

  16. Structural characterisation of pretreated solids from flow-through liquid hot water treatment of sugarcane bagasse in a fixed-bed reactor.

    Science.gov (United States)

    Reddy, Prashant; Lekha, Prabashni; Reynolds, Wienke; Kirsch, Christian

    2015-05-01

    Untreated sugarcane bagasse and sugarcane bagasse pretreated with flow-through liquid hot water (LHW) treatment (170-207°C and 204-250 ml/min) in a fixed-bed reactor have been structurally characterised. Field emission gun scanning electron microscopy (FEG-SEM) and transmission electron microscopy (TEM) were used to investigate changes in the residues, in particular due to the fate of lignin. FEG-SEM results show that the LHW treatment modified the surface morphology of the pretreated bagasse with lignin droplets being observed on the fibre surface. TEM showed an increase in the plant cell wall porosity and lignin migration across the plant cell wall. Increases in pretreatment temperature were observed to increase the average size and density of lignin droplets on the fibre surface. The results provide evidence that for LHW flow-through treatment, just as for batch treatment, lignin repolymerisation and deposition on the surface of pretreated sugarcane bagasse is an important consideration. Copyright © 2015 Elsevier Ltd. All rights reserved.

  17. Oomycete Communities Associated with Reed Die-Back Syndrome

    Directory of Open Access Journals (Sweden)

    Martina Cerri

    2017-09-01

    Full Text Available Phragmites australis (Cav. Trin. ex Steud. die-back is a widely-studied phenomenon that was first discovered in northern Europe and that, until recently, was almost unknown in the Mediterranean basin. It has been described as a complex syndrome affecting reed populations leading to their retreat and decline, with significant impacts on valuable ecosystem services. Among the factors that cause the decline, soil-living microorganisms can be crucial. The aims of this study were to analyze the diversity of oomycetes communities associated with reed stands, and to understand whether they could play a key role in the decline. Variations in the structure of oomycetes communities were studied by metabarcoding of the internal transcribed spacer (ITS 1 region of ribosomal DNA, from the sediments of five Italian freshwater ecosystems. They were chosen to cover a large variability in terms of surface area, water depth, microclimate, and presence of documented reed retreat. From 96 samples collected from reed roots, rhizosphere, and bulk soil, we assembled 207661 ITS1 reads into 523 OTUs. We demonstrated that oomycete communities were structured by several factors, among which the most important was die-back occurrence. Our study also indicates that Pythiogeton spp. could be potentially involved in the development of die-back. The role of heavy metals in the soil was also explored, and cadmium concentration was shown to affect oomycetes distribution. This study represents a significant step forward for the characterization of microbial communities associated with reed die-back syndrome and helps to gain knowledge of the complexity of these important wet ecosystems.

  18. Support material dictates the attached biomass characteristics during the immobilization process in anaerobic continuous-flow packed-bed bioreactor.

    Science.gov (United States)

    Kerčmar, Jasmina; Pintar, Albin

    2017-12-01

    Hydrogen is considered to be an ideal energy alternative to replace environmentally burdensome fossil fuels. For its long-term production the immobilized biofilm system is the most promising and to choose the right support material the most challenging. In this respect, the anaerobic up-flow bioreactors packed with four most used support materials (polyethylene, polyurethane, activated carbon and expanded clay) were tested to investigate the crucial bacteria sensitive period-the immobilization process. Seven-day-operation was necessary and sufficient to reach metabolic and microbial stability regardless of support material used. The support material had an influence on the microbial metabolic activity as well as on quantity and quality characteristics of the immobilized microbial community, being polyethylene and expanded clay more appropriate as supports among the materials evaluated; this could be attributed to pH alteration. The obtained results suggest that the support material dictates the outcome of the immobilization process in the anaerobic continuous-flow bioreactor. Copyright © 2017. Published by Elsevier Ltd.

  19. Reed die-back, water level management and the decline of the great reed warbler Acrocephalus arundinaceus in The Netherlands

    NARCIS (Netherlands)

    Graveland, J.

    1998-01-01

    Several species of migratory marsh birds have declined in Central and Western Europe. An important question is whether this decline is primarily caused by loss of wetlands on the wintering grounds in Africa or by a decline in habitat quality in the breeding areas. Significant losses of Reed

  20. HOBOE (Head-of-Bed Optimization of Elevation) Study: association of higher angle with reduced cerebral blood flow velocity in acute ischemic stroke.

    Science.gov (United States)

    Hunter, Abigail Jade; Snodgrass, Suzanne J; Quain, Debbie; Parsons, Mark W; Levi, Christopher R

    2011-10-01

    Cerebral autoregulation can be impaired after ischemic stroke, with potential adverse effects on cerebral blood flow during early rehabilitation. The objective of this study was to assess changes in cerebral blood flow velocity with orthostatic variation at 24 hours after stroke. This investigation was an observational study comparing mean flow velocities (MFVs) at 30, 15, and 0 degrees of elevation of the head of the bed (HOB). Eight participants underwent bilateral middle cerebral artery (MCA) transcranial Doppler monitoring during orthostatic variation at 24 hours after ischemic stroke. Computed tomography angiography separated participants into recanalized (artery completely reopened) and incompletely recanalized groups. Friedman tests were used to determine MFVs at the various HOB angles. Mann-Whitney U tests were used to compare the change in MFV (from 30° to 0°) between groups and between hemispheres within groups. For stroke-affected MCAs in the incompletely recanalized group, MFVs differed at the various HOB angles (30°: median MFV=51.5 cm/s, interquartile range [IQR]=33.0 to 103.8; 15°: median MFV=55.5 cm/s, IQR=34.0 to 117.5; 0°: median MFV=85.0 cm/s, IQR=58.8 to 127.0); there were no significant differences for other MCAs. For stroke-affected MCAs in the incompletely recanalized group, MFVs increased with a change in the HOB angle from 30 degrees to 0 degrees by a median of 26.0 cm/s (IQR=21.3 to 35.3); there were no significant changes in the recanalized group (-3.5 cm/s, IQR=-12.3 to 0.8). The changes in MFV with a change in the HOB angle from 30 degrees to 0 degrees differed between hemispheres in the incompletely recanalized group but not in the recanalized group. Generalizability was limited by sample size. The incompletely recanalized group showed changes in MFVs at various HOB angles, suggesting that cerebral blood flow in this group may be sensitive to orthostatic variation, whereas the recanalized group maintained stable blood flow

  1. Simulation of Multiphase Flow of the Oil-Water Separation in a Rotating Packed Bed for Oil Purification

    Directory of Open Access Journals (Sweden)

    Xiaojun Zhang

    2013-01-01

    particle contaminant, moisture and gas simultaneously. As the major unit of HIGEE, the RPB uses centrifugal force to intensify mass transfer. Because of the special structure of RPB, the hydraulic characteristics of the RPB are very important. In this study, the multiphase flow model in porous media of the RPB is presented, and the dynamical oil-water separation in the RPB is simulated using a commercial computational fluid dynamics code. The operating conditions and configuration on the hydraulic performance of the RPB are investigated. The results have indicated that the separation efficiency of HIGEE rotating oil purifier is predominantly affected by operating conditions and the configurations. The best inlet pressure is 0.002 MPa. When the liquid inlet is placed in the outside of the lower surface of RPB; oil outlet is placed in the upper surface, where it is near the rotation axis; and water outlet is placed in the middle of the RPB, where it is far away from the oil outlet, the separating efficiency is the best.

  2. Evaluation of reed resources in Latvia and analysis of its use for energy production.

    Science.gov (United States)

    Cubars, Edgars; Noviks, Gotfrids

    2012-04-01

    The increasing demand for energy, limited resources of fossil fuel, as well as pollution of the environment and changes in the global climate have raised more interest about the renewable resources. The use of renewable resources has become a very important partof European Union policy. The aim of the paper was to analyse reed resources in Latvia, its dynamics, volume and quality to produce clean energy. The use of reeds as a renewable energy resource contributes in minimizing fossil fuel consumption. The paper presents the results of a research of reed resources in lakes of Latgale (a region in Latvia). The investigation of reed resources showed that in the region they are scattered and rational usage of them is connected with environmental aspects. The greatest amounts of reed resources are concentrated in the biggest lake in Latvia- Lubana Lake and near to it. Studies showed thatthe reed areas in Lubana Lake and Kvapanu ponds have doubled since 1997 and as a result these water reservoirs are becoming overgrown. Using direct measurement methods and metering from distance, it was stated that the total reed resources of greatest Lake - Lubanas are about 6830 tons year(-1) in area of 734 hectares and are situated in 701 reed blocks. The aggregated reed resources of Latgale region are 18 000 tons year(-1) of dry biomass. The investigation proved that reed resources of the region are sufficient to replace up to 21 thousand tons of different fossil fuels. The physical properties of the reed were measured. Carbon quantity, ash content and structure, moisture content proved that reeds are a profitable fuel for heat energy production. Balanced harvesting of reed gives a positive influence on environment.

  3. Shrubby Reed-Mustard Habitat: Parent Material, Soil, and Landscape Characteristics

    Science.gov (United States)

    Kelly, L. S.; Boettinger, J. L.

    2012-12-01

    Shrubby reed-mustard (Glaucocarpum suffrutescens, a.k.a. Schoenocrambe suffrutescens, Glaucocarpum suffrutescens, or Hesperidanthus suffrutescens) is an endangered perennial shrub endemic to the southern Uinta Basin in northeast Utah. Only seven populations of shrubby reed-mustard have been identified. The arid area where the plant grows is rich in natural gas and oil deposits, as well as oil shale. Oil wells already dot the landscape, and there is significant concern that further development of these resources will threaten the continued existence of shrubby reed-mustard. Determination of the parent material, soil and landscape characteristics associated with shrubby reed-mustard habitat is imperative to facilitate conservation management. Shrubby reed-mustard grows where little else does and, based on field observations and remotely sensed spectral data, appears to occur in a particular type of strata. Our objective is to identify the physical and chemical characteristics of shrubby reed-mustard's environment. Site characteristics such as parent material and associated vegetation have been identified and documented. Soil properties such as water-soluble and total leachable elements, particle-size distribution, organic carbon, cation exchange capacity, total nitrogen, and available phosphorus and potassium are being determined. During the course of this investigation, soils within four shrubby reed-mustard habitat areas were sampled. Soils from non-shrubby reed-mustard areas adjacent to the four shrubby reed-mustard populations were also sampled. Soil samples were collected from a total of twenty-five shrubby reed-mustard soil pits and twenty-four non-shrubby reed-mustard soil pits. The soil horizons of each pedon were delineated, and samples were collected from each horizon. Field data indicate that shrubby reed-mustard occurs exclusively in shale-derived, shallow soils on bedrock-controlled uplands. Although there is some overlap of plant species on both types

  4. An Exploratory Study on the Pathways of Cr (VI) Reduction in Sulfate-reducing Up-flow Anaerobic Sludge Bed (UASB) Reactor

    Science.gov (United States)

    Qian, Jin; Wei, Li; Liu, Rulong; Jiang, Feng; Hao, Xiaodi; Chen, Guang-Hao

    2016-01-01

    Electroplating wastewater contains both Cr (VI) and sulfate. So Cr (VI) removal under sulfate-rich condition is quite complicated. This study mainly investigates the pathways for Cr (VI) removal under biological sulfate-reducing condition in the up-flow anaerobic sludge bed (UASB) reactor. Two potential pathways are found for the removal of Cr (VI). The first one is the sulfidogenesis-induced Cr (VI) reduction pathway (for 90% Cr (VI) removal), in which Cr (VI) is reduced by sulfide generated from biological reduction of sulfate. The second one leads to direct reduction of Cr (VI) which is utilized by bacteria as the electron acceptor (for 10% Cr (VI) removal). Batch test results confirmed that sulfide was oxidized to elemental sulfur instead of sulfate during Cr (VI) reduction. The produced extracellular polymeric substances (EPS) provided protection to the microbes, resulting in effective removal of Cr (VI). Sulfate-reducing bacteria (SRB) genera accounted for 11.1% of the total bacterial community; thus they could be the major organisms mediating the sulfidogenesis-induced reduction of Cr (VI). In addition, chromate-utilizing genera (e.g. Microbacterium) were also detected, which were possibly responsible for the direct reduction of Cr (VI) using organics as the electron donor and Cr (VI) as the electron acceptor. PMID:27021522

  5. Evaluation of an up-flow anaerobic sludge bed (UASB) reactor containing diatomite and maifanite for the improved treatment of petroleum wastewater.

    Science.gov (United States)

    Chen, Chunmao; Liang, Jiahao; Yoza, Brandon A; Li, Qing X; Zhan, Yali; Wang, Qinghong

    2017-11-01

    Novel diatomite (R1) and maifanite (R2) were utilized as support materials in an up-flow anaerobic sludge bed (UASB) reactor for the treatment of recalcitrant petroleum wastewater. At high organic loadings (11kg-COD/m 3 ·d), these materials were efficient at reducing COD (92.7% and 93.0%) in comparison with controls (R0) (88.4%). Higher percentages of large granular sludge (0.6mm or larger) were observed for R1 (30.3%) and R2 (24.6%) compared with controls (22.6%). The larger portion of granular sludge provided a favorable habitat that resulted in greater microorganism diversity. Increased filamentous bacterial communities are believed to have promoted granular sludge formation promoting a conductive environment for stimulation methanogenic Archaea. These communities had enhanced pH tolerance and produced more methane. This study illustrates a new potential use of diatomite and maifanite as support materials in UASB reactors for increased efficiency when treating refractory wastewaters. Copyright © 2017 Elsevier Ltd. All rights reserved.

  6. An Exploratory Study on the Pathways of Cr (VI) Reduction in Sulfate-reducing Up-flow Anaerobic Sludge Bed (UASB) Reactor

    Science.gov (United States)

    Qian, Jin; Wei, Li; Liu, Rulong; Jiang, Feng; Hao, Xiaodi; Chen, Guang-Hao

    2016-03-01

    Electroplating wastewater contains both Cr (VI) and sulfate. So Cr (VI) removal under sulfate-rich condition is quite complicated. This study mainly investigates the pathways for Cr (VI) removal under biological sulfate-reducing condition in the up-flow anaerobic sludge bed (UASB) reactor. Two potential pathways are found for the removal of Cr (VI). The first one is the sulfidogenesis-induced Cr (VI) reduction pathway (for 90% Cr (VI) removal), in which Cr (VI) is reduced by sulfide generated from biological reduction of sulfate. The second one leads to direct reduction of Cr (VI) which is utilized by bacteria as the electron acceptor (for 10% Cr (VI) removal). Batch test results confirmed that sulfide was oxidized to elemental sulfur instead of sulfate during Cr (VI) reduction. The produced extracellular polymeric substances (EPS) provided protection to the microbes, resulting in effective removal of Cr (VI). Sulfate-reducing bacteria (SRB) genera accounted for 11.1% of the total bacterial community; thus they could be the major organisms mediating the sulfidogenesis-induced reduction of Cr (VI). In addition, chromate-utilizing genera (e.g. Microbacterium) were also detected, which were possibly responsible for the direct reduction of Cr (VI) using organics as the electron donor and Cr (VI) as the electron acceptor.

  7. Photoassisted Fenton degradation of phthalocyanine dyes from wastewater of printing industry using Fe(II)/γ-Al2O3 catalyst in up-flow fluidized-bed.

    Science.gov (United States)

    Cheng, Hsuhui; Chou, Shihjie; Chen, Shiaoshing; Yu, Chiajen

    2014-06-01

    Fe(II)/γ-Al2O3 powders synthesized using the dipping method were produced from a mixed aqueous solution containing aluminium oxide (γ-Al2O3) and iron(II)-precursor (FeSO4), and used for photo-Fenton degradation of phthalocyanine dyes (PCS) under ultraviolet (UV) irradiation in an up-flow fluidized bed. The catalysts were characterized by XRD, ESCA, BET, EDS and SEM. The results showed that Fe(2+) ion was compounded on the γ-Al2O3 carrier. The effects of different reaction parameters such as catalyst activity, dosage and solution pH on the decolorization of PCS were assessed. Results indicated that maximum decolorization (more than 95%) of PCS occurred with 20 wt% Fe(II)/γ-Al2O3 catalyst (dosage of 60 g/L) using a combination of UV irradiation and heterogeneous Fenton system. The degradation efficiency of PCS increases as pH decreases, exhibiting a maximum efficiency at pH 3.5. The recycled catalyst was capable of repeating three runs without a significant decrease in treatment efficiency, and this demonstrated the stability and reusability of catalyst. Copyright © 2014 The Research Centre for Eco-Environmental Sciences, Chinese Academy of Sciences. Published by Elsevier B.V. All rights reserved.

  8. Dorothy Reed and Hodgkin's disease: a reflection after a century

    International Nuclear Information System (INIS)

    Zwitter, Matjaz; Cohen, Joel R.; Barrett, Ann; Robinton, Elizabeth D.

    2002-01-01

    It has now been 100 years since Dorothy Reed, at the age of 28, wrote her paper on Hodgkin's disease. Her biography reveals the difficult lives of women entering the hitherto male-dominated field of medicine, let alone medical research. Her historic paper on Hodgkin's disease is remarkable for its brilliant observations and concise scientific reasoning. Nevertheless, she was told that as a woman she could not hope for a career as an academic pathologist. After marriage to Charles Elwood Mendenhall, Professor of Physics at the University of Wisconsin and after giving birth to four children, the second part of her career began. Motivated by the loss of her firstborn, she began a study of infant mortality, an interest that lasted throughout her career. In 1926, Mendenhall undertook a survey comparing infant and maternal mortality rates in Denmark and the United States. This influential study concluded that American mortality rates were higher because of unnecessary interference in the natural process of childbirth and recommended the education of midwives follow the Danish model. In 1937, her efforts were rewarded when Madison, WI received recognition for having the lowest infant mortality of any city in the United States. Reading Reed's paper on Hodgkin's disease, we see that her observations go far beyond a description of a specific cell. Her presentation of macroscopic and microscopic features is remarkable for the distinction between 'young' and 'old' growths: Reed saw Hodgkin's disease as a process, rather than the spreading of a cancer. She was the first to note that those most commonly affected are boys or young adults, especially those whose general health before the disease had been excellent. She was also the first to note anergy to tuberculin. Dorothy Reed defined Hodgkin's disease in relation to tuberculosis, described its pathologic features, and offered comments on its pathogenesis, epidemiology, and immunology that still deserve to be discussed

  9. Balanced Reed-Solomon codes for all parameters

    KAUST Repository

    Halbawi, Wael

    2016-10-27

    We construct balanced and sparsest generator matrices for cyclic Reed-Solomon codes with any length n and dimension k. By sparsest, we mean that each row has the least possible number of nonzeros, while balanced means that the number of nonzeros in any two columns differs by at most one. Codes allowing such encoding schemes are useful in distributed settings where computational load-balancing is critical. The problem was first studied by Dau et al. who showed, using probabilistic arguments, that there always exists an MDS code over a sufficiently large field such that its generator matrix is both sparsest and balanced. Motivated by the need for an explicit construction with efficient decoding, the authors of the current paper showed that the generator matrix of a cyclic Reed-Solomon code of length n and dimension k can always be transformed to one that is both sparsest and balanced, when n and k are such that k/n (n-k+1) is an integer. In this paper, we lift this condition and construct balanced and sparsest generator matrices for cyclic Reed-Solomon codes for any set of parameters.

  10. Buffer management to solve bed-blocking in the Netherlands, 2000-2010. Cooperation from an integrated care chain perspective as a key success factor for managing patient flows.

    Directory of Open Access Journals (Sweden)

    Ingrid Mur

    2011-07-01

    Full Text Available Introduction: Bed-blocking problems in hospitals reflect how difficult and complex it is to move patients smoothly through the chain of care. In the Netherlands, during the first decade of the 21st century, some hospitals attempted to tackle this problem by using an Intermediate Care Department (ICD as a buffer for bed-blockers. However, research has shown that ICDs do not sufficiently solve the bed-blocking problem and that bed-blocking is often caused by a lack of buffer management.Tool: Buffer management (BM is a tool that endeavors to balance patient flow in the hospital to nursing home chain of care. Results: Additional research has indicated that the absence of BM is not the result of providers' thinking that BM is unnecessary, unethical or impossible because of unpredictable patient flows. Instead, BM is hampered by a lack of cooperation between care providers.Conclusion: Although stakeholders recognize that cooperation is imperative, they often fail to take the actions necessary to realize cooperation. Our assumption is that this lack of willingness and ability to cooperate is the result of several impeding conditions as well as stakeholders' perceptions of these conditions and the persistence of their current routines, principles and beliefs (RPBs.Discussion: We recommend simultaneously working on improving the conditions and changing stakeholders' perceptions and RPBs.

  11. Application of subsurface vertical flow constructed wetlands to reject water treatment in dairy wastewater treatment plant.

    Science.gov (United States)

    Dąbrowski, Wojciech; Karolinczak, Beata; Gajewska, Magdalena; Wojciechowska, Ewa

    2017-01-01

    The paper presents the effects of applying subsurface vertical flow constructed wetlands (SS VF) for the treatment of reject water generated in the process of aerobic sewage sludge stabilization in the biggest dairy wastewater treatment plant (WWTP) in Poland. Two SS VF beds were built: bed (A) with 0.65 m depth and bed (B) with 1.0 m depth, planted with reeds. Beds were fed with reject water with hydraulic load of 0.1 m d -1 in order to establish the differences in treatment efficiency. During an eight-months research period, a high removal efficiency of predominant pollutants was shown: BOD 5 88.1% (A) and 90.5% (B); COD 84.5% (A) and 87.5% (B); TSS 87.6% (A) and 91.9% (B); TKN 82.4% (A) and 76.5% (B); N-NH 4 + 89.2% (A) and 85.7% (B); TP 30.2% (A) and 40.6% (B). There were not statistically significant differences in the removal efficiencies between bed (B) with 1.0 m depth and bed (A) with 0.65 m depth. The research indicated that SS VF beds could be successfully applied to reject water treatment in dairy WWTPs. The study proved that the use of SS VF beds in full scale in dairy WWTPs would result in a significant decrease in pollutants' load in reject water. In the analyzed case, decreasing the load of ammonia nitrogen was of greatest importance, as it constituted 58% of the total load treated in dairy WWTP and posed a hazard to the stability of the treatment process.

  12. Particle bed reactor modeling

    Science.gov (United States)

    Sapyta, Joe; Reid, Hank; Walton, Lew

    The topics are presented in viewgraph form and include the following: particle bed reactor (PBR) core cross section; PBR bleed cycle; fuel and moderator flow paths; PBR modeling requirements; characteristics of PBR and nuclear thermal propulsion (NTP) modeling; challenges for PBR and NTP modeling; thermal hydraulic computer codes; capabilities for PBR/reactor application; thermal/hydralic codes; limitations; physical correlations; comparison of predicted friction factor and experimental data; frit pressure drop testing; cold frit mask factor; decay heat flow rate; startup transient simulation; and philosophy of systems modeling.

  13. Fate of xenobiotic compounds and plants activity in reed bed sludge treatment

    DEFF Research Database (Denmark)

    Chen, Xijuan; Pauli, Udo; Rehfus, Stefan

    unplanted in order to distinguish the impact of the root system on the performance of the containers. After twelve months OTNE, Triclosan and DEHP were significant degraded with half-lives of 187-204 days for OTNE, 330-462 days for Triclosan and 315-533 days for DEHP.  HHCB and AHTN have half-lives of 770...

  14. Co-circulation of Usutu virus and West Nile virus in a reed bed ecosystem

    Czech Academy of Sciences Publication Activity Database

    Rudolf, Ivo; Bakonyi, T.; Šebesta, Oldřich; Mendel, Jan; Peško, Juraj; Betášová, Lenka; Blažejová, Hana; Venclíková, Kristýna; Straková, Petra; Nowotny, N.; Hubálek, Zdeněk

    2015-01-01

    Roč. 8, č. 520 (2015), s. 520 ISSN 1756-3305 EU Projects: European Commission(XE) 261504 - EDENEXT Institutional support: RVO:68081766 Keywords : Culex modestus * Usutu virus * West Nile virus * Flavivirus * Arbovirus * Surveillance * Mosquitoes Subject RIV: EE - Microbiology, Virology Impact factor: 3.234, year: 2015

  15. The Hybrid Mineral Battery: energy storage and dissolution behavior of CuFeS2 in a fixed bed flow cell.

    Science.gov (United States)

    Deen, Kashif Mairaj; Asselin, Edouard

    2018-03-08

    The development of a hybrid system, capable of storing energy, and with the additional benefit of Cu extraction is discussed in this work. A fixed bed flow cell (FBFC) was used in which a composite negative electrode containing CuFeS2 (80 wt. %) and carbon black (20 wt. %) in graphite felt was separated from a positive (graphite felt) electrode by proton exchange membrane. The anolyte (0.2M H2SO4) and catholyte (0.5M Fe2+ in 0.2M H2SO4 with or without 0.1M Cu2+ addition) were circulated in the cell. With the addition of Cu2+ in the catholyte, the electrochemical activity of the Fe2+/Fe3+ redox couple over graphite felt was significantly improved. Ultimately, in the CuFeS2||Fe2+/Cu2+ (CFeCu) FBFC system the specific capacity increased continuously to 26.4 mAh-g-1 in 500 galvanostatic charge/discharge (GCD) cycles, compared to the CuFeS2||Fe2+ (CFe) system (13.9 mAh-g-1). Interestingly, the specific discharge energy gradually increased to 3.6 Wh-kg-1 in 500 GCD cycles for the CFeCu system compared to 3.29 Wh-kg-1 for the CFe system in 150 cycles. In addition to the energy storage, 10.75 % Cu was also extracted from the mineral, which is an important feature of CFeCu system as it would allow for Cu extraction and recovery through hydrometallurgical methods. © 2018 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  16. In-Bed Accountability Development for a Passively Cooled, Electrically Heated Hydride (PACE) Bed

    International Nuclear Information System (INIS)

    Klein, J.E.

    2005-01-01

    A nominal 1500 STP-L PAssively Cooled, Electrically heated hydride (PACE) Bed has been developed for implementation into a new Savannah River Site tritium project. The 1.2 meter (four-foot) long process vessel contains on internal 'U-tube' for tritium In-Bed Accountability (IBA) measurements. IBA will be performed on six, 12.6 kg production metal hydride storage beds.IBA tests were done on a prototype bed using electric heaters to simulate the radiolytic decay of tritium. Tests had gas flows from 10 to 100 SLPM through the U-tube or 100 SLPM through the bed's vacuum jacket. IBA inventory measurement errors at the 95% confidence level were calculated using the correlation of IBA gas temperature rise, or (hydride) bed temperature rise above ambient temperature, versus simulated tritium inventory.Prototype bed IBA inventory errors at 100 SLPM were the largest for gas flows through the vacuum jacket: 15.2 grams for the bed temperature rise and 11.5 grams for the gas temperature rise. For a 100 SLPM U-tube flow, the inventory error was 2.5 grams using bed temperature rise and 1.6 grams using gas temperature rise. For 50 to 100 SLPM U-tube flows, the IBA gas temperature rise inventory errors were nominally one to two grams that increased above four grams for flows less than 50 SLPM. For 50 to 100 SLPM U-tube flows, the IBA bed temperature rise inventory errors were greater than the gas temperature rise errors, but similar errors were found for both methods at gas flows of 20, 30, and 40 SLPM.Electric heater IBA tests were done for six production hydride beds using a 45 SLPM U-tube gas flow. Of the duplicate runs performed on these beds, five of the six beds produced IBA inventory errors of approximately three grams: consistent with results obtained in the laboratory prototype tests

  17. In-Bed Accountability Development for a Passively Cooled, Electrically Heated Hydride (PACE) Bed

    International Nuclear Information System (INIS)

    KLEIN, JAMES

    2004-01-01

    A nominal 1500 STP-L PAssively Cooled, Electrically heated hydride (PACE) Bed has been developed for implementation into a new Savannah River Site tritium project. The 1.2 meter (four-foot) long process vessel contains an internal ''U-tube'' for tritium In-Bed Accountability (IBA) measurements. IBA will be performed on six, 12.6 kg production metal hydride storage beds. IBA tests were done on a prototype bed using electric heaters to simulate the radiolytic decay of tritium. Tests had gas flows from 10 to 100 SLPM through the U-tube or 100 SLPM through the bed's vacuum jacket. IBA inventory measurement errors at the 95 percent confidence level were calculated using the correlation of IBA gas temperature rise, or (hydride) bed temperature rise above ambient temperature, versus simulated tritium inventory. Prototype bed IBA inventory errors at 100 SLPM were the largest for gas flows through the vacuum jacket: 15.2 grams for the bed temperature rise and 11.5 grams for the gas temperature rise. For a 100 SLPM U-tube flow, the inventory error was 2.5 grams using bed temperature rise and 1.6 grams using gas temperature rise. For 50 to 100 SLPM U-tube flows, the IBA gas temperature rise inventory errors were nominally one to two grams that increased above four grams for flows less than 50 SLPM. For 50 to 100 SLPM U-tube flows, the IBA bed temperature rise inventory errors were greater than the gas temperature rise errors, but similar errors were found for both methods at gas flows of 20, 30, and 40 SLPM. Electric heater IBA tests were done for six production hydride beds using a 45 SLPM U-tube gas flow. Of the duplicate runs performed on these beds, five of the six beds produced IBA inventory errors of approximately three grams: consistent with results obtained in the laboratory prototype tests

  18. Islands in a desert : breeding ecology of the African Reed Warbler Acrocephalus baeticatus in Namibia

    NARCIS (Netherlands)

    Eising, CM; Komdeur, J; Buys, J; Reemer, M; Richardson, DS; Richardson, David S.

    The continental African Reed Warbler Acrocephalus baeticatus, like its relative the Seychelles Warbler Acrocephalus sechellensis, breeds in isolated patches. We studied the mating system of the African Reed Warbler to see whether this species, like the Seychelles Warbler, shows co-operative

  19. Ecosystem Service Value for the Common Reed Wetlands in the Liaohe Delta, Northeast China

    DEFF Research Database (Denmark)

    Ye, Siyuan; Laws, Edward A.; Costanza, Robert

    2016-01-01

    The largest reed field in the world, with an area of 1000 km2 in 1953, is located in the Liaohe Delta, which lies in the five-point-in-a-line economic strategic zone of northeastern China. However, the area of reeds has declined dramatically in recent years to accommodate oil field infrastructure...

  20. 77 FR 43369 - Lexisnexis, a Subsidiary of Reed Elsevier Customer Service Department and Fulfillment Department...

    Science.gov (United States)

    2012-07-24

    ..., a Subsidiary of Reed Elsevier Customer Service Department and Fulfillment Department, Including On... Customer Service Department and Fulfillment Department, Including On-Site Leased Workers From Manpower... subsidiary of Reed Elsevier, Inc., Customer Service Department and Fulfillment Department, including on-site...

  1. The vibrating reed frequency meter : digital investigation of an early cochlear model

    NARCIS (Netherlands)

    Bell, Andrew; Wit, Hero P.

    2015-01-01

    The vibrating reed frequency meter, originally employed by Bekesy and later by Wilson as a cochlear model, uses a set of tuned reeds to represent the cochlea's graded bank of resonant elements and an elastic band threaded between them to provide nearest-neighbour coupling. Here the system,

  2. Adsorption Behavior and Mechanism for the Uptake of Fluoride Ions by Reed Residues.

    Science.gov (United States)

    Song, Rong; Yang, Shengke; Xu, Haiyang; Wang, Zongzhou; Chen, Yangyang; Wang, Yanhua

    2018-01-09

    The adsorption behavior and mechanism for the uptake of fluoride ions by untreated and desugared reed residues (roots, stems and leaves) were studied through adsorption experiments, elemental analysis, infrared spectroscopy and surface area analysis. The results showed that the adsorption capacity of untreated and desugared reeds followed the order: desugared roots 2136 mg/kg > desugared leaves 1825 mg/kg > desugared stems 1551 mg/kg > untreated roots 191 mg/kg > untreated stems 175 mg/kg > untreated leaves 150 mg/kg, so adsorption capacity of desugared reeds was larger than that of the untreated reeds. The adsorption kinetic of fluoride ions followed a pseudo-first-order model. A Langmuir model could be used to fit the isothermal adsorption process which was a spontaneous endothermic reaction involving mainly physical adsorption. The ΔG for the uptake of fluoride by the desugared reeds was more negative, so the degree of spontaneity was higher than for the use of the untreated reeds. After samples were desugared, the specific surface area and aromaticity of the reed increased, while the polarity and hydrophilicity decreased, which explained the adsorption amount of desugared reed was higher than that of the untreated. This study enriches techniques and methods of removing fluoride ions from water.

  3. Tracing the contribution of debris flow-dominated channels to gravel-bed torrential river channel: implementing pit-tags in the upper Guil River (French Alps)

    Science.gov (United States)

    Arnaud-Fassetta, Gilles; Lissak, Candide; Fort, Monique; Bétard, François; Carlier, Benoit; Cossart, Etienne; Madelin, Malika; Viel, Vincent; Charnay, Bérengère; Bletterie, Xavier

    2014-05-01

    Morel (20 pit-tags), Bouchouse (40 pit-tags), Peyronnelle (100 pit-tags). All pit-tags were installed high upstream enough in each catchment to avoid their loss and/or burying, and permit their monitoring over several years. The grain size (D50 = 30-220 cm) of the selected blocks reflects the average size of the bed load. Smaller blocks were discarded to avoid losing their track from the first event. The blocks were positioned according to two logics: (i) Longitudinally, we implemented every 20-30 m a series of nested blocks into the channel; (ii) Transversally, we selected blocks placed in low and high position to quantify the transport dynamics during events of low (torrential) and high (debris flow) magnitude. The sites were mapped at high resolution, and blocks were spotted thanks to fluorescent painting, GPS surveys and detailed photographs. We emplaced the pit-tags in September 2013, before expected avalanches and debris flows during winter and spring 2014. Pit-tags detection, Lidar and photogrammetric surveys are planned for early summer 2014, during which we expect quantifying movement, distance and sorting of blocks along the thalwegs during "ordinary" snowmelt runoff. We intend to continue this monitoring long enough to put observed current and future dynamics in relation to short-term climatic changes.

  4. Fluidized-bed nuclear reactor

    International Nuclear Information System (INIS)

    Grimmett, E.S.; Kunze, J.F.

    1975-01-01

    A reactor vessel containing a fluidized-bed region of particulate material including both a neutron-moderating and a fertile substance is described. A gas flow including fissile material passes through the vessel at a sufficient rate to fluidize the particulate material and at a sufficient density to support a thermal fission reaction within the fluidized-bed region. The high-temperature portion of a heat transfer system is located within the fluidized-bed region of the reactor vessel in direct contact with the fluidized particles. Heat released by fission is thereby transferred at an enhanced rate to a coolant circulating within the heat transfer system. Fission products are continuously removed from the gas flow and supplemental fissile material added during the reactor operation. (U.S.)

  5. Bed topography and sand transport responses to a step change in discharge and water depth

    Science.gov (United States)

    Ephemeral streams with sand and gravel beds may inherit bed topography caused by previous flow events, resulting in bed topography that is not in equilibrium with flow conditions, complicating the modeling of flow and sediment transport. Major flow events, resulting from rainfall with high intensity...

  6. Enzymatic Saccharification and Ethanol Fermentation of Reed Pretreated with Liquid Hot Water

    Directory of Open Access Journals (Sweden)

    Jie Lu

    2012-01-01

    Full Text Available Reed is a widespread-growing, inexpensive, and readily available lignocellulosic material source in northeast China. The objective of this study is to evaluate the liquid hot water (LHW pretreatment efficiency of reed based on the enzymatic digestibility and ethanol fermentability of water-insoluble solids (WISs from reed after the LHW pretreatment. Several variables in the LHW pretreatment and enzymatic hydrolysis process were optimized. The conversion of glucan to glucose and glucose concentrations are considered as response variables in different conditions. The optimum conditions for the LHW pretreatment of reed area temperature of 180°C for 20min and a solid-to-liquid ratio of 1 : 10. These optimum conditions for the LHW pretreatment of reed resulted in a cellulose conversion rate of 82.59% in the subsequent enzymatic hydrolysis at 50°C for 72 h with a cellulase loading of 30 filter paper unit per gram of oven-dried WIS. Increasing the pretreatment temperature resulted in a higher enzymatic digestibility of the WIS from reed. Separate hydrolysis and fermentation of WIS showed that the conversion of glucan to ethanol reached 99.5% of the theoretical yield. The LHW pretreatment of reed is a suitable method to acquire a high recovery of fermentable sugars and high ethanol conversion yield.

  7. A STUDY OF RECOVERING A REED ECOSYSTEM USING POROUS CONCRETE IN THE LAKE BIWA SHORE

    Science.gov (United States)

    Takeda, Naho; Kato, Hayato; Okamoto, Takahisa; Kojima, Takayuki

    In this study, reed planting tests were carried out at the Biyo-center, an experiment station on the Lake Biwa shore, in order to evaluate the feasibility of a planting method with porous concrete (PoC method). Reed planting tests with coconut-fiber mats (mat method), which were generally used around Lake Biwa, were simultaneously carried out to compare with the PoC method. The reeds planted by the PoC method grew better than the ones planted by the mat method, and the number of reeds which were washed away by waves was smaller than that planted by the mat method. The result of the observation of reeds planted in the PoC showed plant maturation, and reeds could ta ke root into the PoC without interference with the voids of the PoC. As a result, it was shown that the reed planting tests with the PoC method was simple and effective, so it would become in harmony with the environment around Lake Biwa.

  8. An exploration of common reed (Phragmites australis bioenergy potential in North America

    Directory of Open Access Journals (Sweden)

    R. Vaičekonytė

    2014-10-01

    Full Text Available In North America, reed (Phragmites australis is typically considered to be a weed although it provides important ecosystem services. Small, sparse, patchy or mixed reedbeds are more suitable as habitat for many species than extensive dense reedbeds, whose habitat functions can be enhanced by the selective removal of biomass. We propose that above-ground reed biomass could be harvested for bioenergy, at the same time improving habitat for biodiversity by thinning or fragmenting the more extensive reedbeds. Biofuel pellets manufactured from reeds harvested at Montréal (Canada had moisture content 6.4 %, energy content 16.9 kJ g-1 (dry mass, ash content 3.44 %, and chloride content 1962 ppm. Thus, reed as a material for fuel pellet manufacture is similar to switchgrass (Panicum virgatum, which is commonly cultivated for that purpose and requires higher inputs than harvested wild reed. We discuss these findings in the context of environmental considerations and conclude that the bioenergy potential of reed could most expediently be realised in North America by combining material harvested from the widespread spontaneously occurring reedbeds with organic waste from other sources to create mixed biofuels. However, reeds with high levels of chlorine, sulphur or metals should not be burned to avoid air pollution or equipment damage unless these problems are mitigated by means of appropriate season of harvest, equipment, combustion regime, or use of a mixed feedstock.

  9. Biodegradation of Methyl Tertiary Butyl Ether (MTBE by a Microbial Consortium in a Continuous Up-Flow Packed-Bed Biofilm Reactor: Kinetic Study, Metabolite Identification and Toxicity Bioassays.

    Directory of Open Access Journals (Sweden)

    Guadalupe Alfonso-Gordillo

    Full Text Available This study investigated the aerobic biodegradation of methyl tertiary-butyl ether (MTBE by a microbial consortium in a continuous up-flow packed-bed biofilm reactor using tezontle stone particles as a supporting material for the biofilm. Although MTBE is toxic for microbial communities, the microbial consortium used here was able to resist MTBE loading rates up to 128.3 mg L-1 h-1, with removal efficiencies of MTBE and chemical oxygen demand (COD higher than 90%. A linear relationship was observed between the MTBE loading rate and the MTBE removal rate, as well as between the COD loading rate and the COD removal rate, within the interval of MTBE loading rates from 11.98 to 183.71 mg L-1 h-1. The metabolic intermediate tertiary butyl alcohol (TBA was not detected in the effluent during all reactor runs, and the intermediate 2-hydroxy butyric acid (2-HIBA was only detected at MTBE loading rates higher than 128.3 mg L-1 h-1. The results of toxicity bioassays with organisms from two different trophic levels revealed that the toxicity of the influent was significantly reduced after treatment in the packed-bed reactor. The packed-bed reactor system used in this study was highly effective for the continuous biodegradation of MTBE and is therefore a promising alternative for detoxifying MTBE-laden wastewater and groundwater.

  10. Development of control rod position indicator using reed switch for SMART CEDM

    International Nuclear Information System (INIS)

    Yoo, Jae Yong; Kim, Jong In; Kim, Ji Ho; Huh, Hyoung; Jang, Moon Hee

    2001-01-01

    The reliability and accuracy of the information on control rod position are very important to the reactor safety and the design of the core protection system. In this study, a thorough investigation on the RSPT(Reed Switch Position Transmitter) type control rod position indication system and its actual implementation in the exiting nuclear power plants in Korea was performed first. A design of the control rod position indication system using reed switch for the CEDM on the integral reactor SMART was developed based on the position indicator technology identified through the investigation. The feasibility of the design was evaluated by test of manufactured control rod position indicator using reed switch for SMART

  11. Gas Distribution in Shallow Packed Beds.

    Science.gov (United States)

    Parsons, Ian Miles

    Available from UMI in association with The British Library. Packed beds have many industrial applications and are increasingly used in the process industries due to their low pressure drop. Obtaining uniform gas distribution in such beds is of crucial importance in minimising operating costs and optimising plant performance. Since to some extent a packed bed acts as its own distributor the importance of obtaining uniform gas distribution has increased as aspect ratios (bed height to diameter) decrease. There is no rigorous design method for distributors due to a limited understanding of the fluid flow phenomena and in particular of the effect of the bed base/free fluid interface. This study is based on a combined theoretical and modelling approach. The Ergun Equation is used to determine the pressure drop over a bed where the flow is uni-directional. This equation has been used in a vectorial form so that it can be applied to maldistributed and multi -directional flows and has been realised in the Computational Fluid Dynamics code PHOENICS. The use of this equation and its application has been verified by modelling experimental measurements of maldistributed gas flows, where there is no free fluid/bed base interface. A novel, two-dimensional experiment has been designed to investigate the fluid mechanics of maldistributed gas flows in shallow packed beds. The results from this apparatus provide useful insights into the fluid mechanics of flow in and around a shallow packed bed and show the critical effect of the bed base. The PHOENICS/vectorial Ergun Equation model has been adapted to model this situation. The model has been improved by the inclusion of spatial voidage variations in the bed and the prescription of a novel bed base boundary condition. The flow in a curved bed section, which is three -dimensional in nature, is examined experimentally. The effect of the walls and the changes in gas direction on the gas flow are shown to be particularly significant

  12. Incipient motion of gravel and coal beds

    Indian Academy of Sciences (India)

    R. Narasimhan (Krishtel eMaging) 1461 1996 Oct 15 13:05:22

    turbulent regime, identified based on physical reasoning and dimensional analysis, are the Shields parameter, particle Froude number, non-dimensional particle diameter and non-dimensional flow depth. Equations of critical bed shear stress ...

  13. Anthocyanins from maize (Zea mays) and reed canarygrass (Phalaris arundinacea).

    Science.gov (United States)

    Fossen, T; Slimestad, R; Andersen, O M

    2001-05-01

    Flowers of maize, Zea mays, and reed canarygrass, Phalaris arundinacea, contain the same anthocyanins: cyanidin 3-glucoside, cyanidin 3-(6' '-malonylglucoside), cyanidin 3-(3' ',6' '-dimalonylglucoside), peonidin 3-glucoside, peonidin 3-(6' '-malonylglucoside), and peonidin 3-(dimalonylglucoside). The latter pigment has previously not been reported to occur in plants. Structure elucidations were primarily based on homo- and heteronuclear two-dimensional NMR and electrospray MS. During the isolation procedure using various mixtures of H(2)O, CF(3)CO(2)H, and CH(3)OH, and during storage in NMR solvent (CF(3)CO(2)D/CD(3)OD; 1:19, v/v) methyl esterification of the free acid function of the malonyl units of the pigments occurs. The acylated anthocyanins constitute more than 80% and 40% of the anthocyanins in P. arundinacea and Z. mays, respectively. Flowers and leaves of maize, Zea mays, contain the same anthocyanins in nearly equal relative proportions.

  14. An in situ spatially resolved analytical technique to simultaneously probe gas phase reactions and temperature within the packed bed of a plug flow reactor.

    Science.gov (United States)

    Touitou, Jamal; Burch, Robbie; Hardacre, Christopher; McManus, Colin; Morgan, Kevin; Sá, Jacinto; Goguet, Alexandre

    2013-05-21

    This paper reports the detailed description and validation of a fully automated, computer controlled analytical method to spatially probe the gas composition and thermal characteristics in packed bed systems. As an exemplar, we have examined a heterogeneously catalysed gas phase reaction within the bed of a powdered oxide supported metal catalyst. The design of the gas sampling and the temperature recording systems are disclosed. A stationary capillary with holes drilled in its wall and a moveable reactor coupled with a mass spectrometer are used to enable sampling and analysis. This method has been designed to limit the invasiveness of the probe on the reactor by using the smallest combination of thermocouple and capillary which can be employed practically. An 80 μm (O.D.) thermocouple has been inserted in a 250 μm (O.D.) capillary. The thermocouple is aligned with the sampling holes to enable both the gas composition and temperature profiles to be simultaneously measured at equivalent spatially resolved positions. This analysis technique has been validated by studying CO oxidation over a 1% Pt/Al2O3 catalyst and the spatial resolution profiles of chemical species concentrations and temperature as a function of the axial position within the catalyst bed are reported.

  15. Attempts on cardoon gasification in two different circulating fluidized beds

    Directory of Open Access Journals (Sweden)

    Chr. Christodoulou

    2014-11-01

    Full Text Available Few tests have been carried out in order to evaluate the use of cardoon in gasification and combustion applications most of the researchers dealt with agglomeration problems. The aim of this work is to deal with the agglomeration problem and to present a solution for the utilization of this biofuel at a near industrial application scale. For this reason, two experiments were conducted, one in TU Delft and one in Centre for Research and Technology Hellas (CERTH, using fuel cardoon and 50% w/w cardoon blended with 50% w/w giant reed respectively. Both experimental campaigns were carried out in similar atmospheric circulating fluidized bed gasifiers. Apart from the feedstock, the other differences were the gasification medium and the bed material used in each trial. The oxidizing agent at TUD׳s run was O2/steam, whereas CERTH׳s tests used air. When experiments with the cardoon 50% w/w–giant reed 50% w/w blend were performed no agglomeration problems were presented. Consequently, gasification could be achieved in higher temperature than that of pure cardoon which led to the reduction of tar concentration.

  16. Correlation of voidage and stress of granular materials in a packed moving bed accompanied with gas flow; Gasu nagare wo tomonau funtai idoso ni okeru kugekiritsu to funtaiatsu no kankei ni tsuite

    Energy Technology Data Exchange (ETDEWEB)

    Tomoyasu, Yoshitada. [Sanzou Energy Engineering Corp., Okayama (Japan); Yoshino, Fumio.; Iwata, Hiroshi.; Kawazoe, Hiromitsu. [Tottori University, Tottori (Japan). Dept. of Mechanical Engineering

    1999-03-10

    The flow characteristics of granular materials and gas in a vertical packed moving bed, called a [stand pipe], furnished at the bottom of the fluidized bed are investigated theoretically and experimentally. A correlation equation of axial stress {sigma}{sub z} and voidage {epsilon} of granular materials in the stand pipe is proposed through investigations of the continuity equation, the momentum balance equation, Ergun's equation for gas pressure loss and the gas pressure distribution data measured experimentally in the axial direction. Regarding the relation of the axial stress and the voidage, it was recogniged that : 1. The absolute value of d{sigma}{sub z}/d{epsilon} is large at the voidage near the minimum fluidizing condition, and at the voidage in the dense packed condition, and an inflection point of {sigma}{sub z} exists in range between the both conditions ; 2. It seems to be the wall-friction-effect of stand pipe that the absolute value of d{sigma}{sub z}/d{epsilon} is larger at the inlet of stand pipe, and ; 3. The stress is also a function of the particle diameter. The gas flow rate, axial stress distribution of granular materials, gas pressure distribution and voidage distribution in the axial direction of the stand pipe can be calculated from relating equations. (author)

  17. Paraskeva pühastest ja reede kultusest Satserinna kiriklikus traditsioonis / Kai Kuusing

    Index Scriptorium Estoniae

    Kuusing, Kai

    2005-01-01

    Saatse kirikust pärit Paraskeva pühaste (ikoonide) ikonograafia- ja hagiograafiaalasest materjalist ning Paraskeva kultusega seotud kahest erinevast traditsioonist Saatse kirikus - Ikonioni Paraskeva mälestuspäeva ja Eelija reede pühitsemisest

  18. Ultrastructural localization of Leu M1 in Reed-Sternberg cells and normal myeloid cells.

    Science.gov (United States)

    Warhol, M J; Pinkus, G S; Said, J W

    1987-08-01

    An antigen Leu M1 has been localized to myelomonocytic cells and Reed-Sternberg cells by light microscopic immunocytochemical studies. We used both pre- and post-embedding immunoelectron microscopy to define the ultrastructural distribution of this antigen. Post-embedding techniques heavily labeled the granules of polymorphonuclear leukocytes and the nonspecific granules of eosinophils. At high concentrations there was labeling of the specific granules of the eosinophil. The antibody consistently labeled the perinuclear granules and vesicles of Reed-Sternberg cells. Some Reed-Sternberg cells also exhibited labeling of the endoplasmic reticulum, suggesting that these cells have the capacity to synthesize this antigen. Although plasma membranes were labeled with the post-embedding technique, these structures were most heavily labeled with the pre-embedding method. These results indicate that Leu M1 is synthesized and packaged by Reed-Sternberg cells and represents an integral structural component of these cells.

  19. Flue gas desulfurization by rotating beds

    Energy Technology Data Exchange (ETDEWEB)

    Gardner, N.; Keyvani, M.; Coskundeniz, A.

    1992-01-01

    The operating and mass transfer characteristics of rotating foam metal beds were studied to determine the potential for flue gas desulfurization. This is a final technical report on the work supported by DOE [number sign]FG22-87-PC79924. The report is divided into two sections, Part 1 deals primarily with the operating characteristics of rotating beds, and Part 2 covers the mass transfer characteristics of S0[sub 2] absorption in water-lime slurries. Rotating foam metal beds are in essence packed towers operated in high gravitational fields. The foam metal bed is in the form of a cylindrical donut, or torus, and is rotated to produced the high centrifugal forces. The liquid phase enters the bed at the inner surface of the torus and is pulled by the field through the bed. Gas flows countercurrent to the liquid. The bed packing can have a very large specific surface areas and not flood. Possible benefits include much smaller height of a transfer unit resulting in smaller equipment and supporting structures, reduced solvent inventory, faster response with improved process control, reduced pressure drop, and shorter startup and shut-down times. This work is concerned broadly with the operating characteristics of rotating beds, the objectives being to (1) determine the pressure drop through the rotating bed; (2) determine the power required to operate the beds, (3) investigate the residence time distribution of the liquid phase in the beds; and (4) determine the mass transfer coefficients of S0[sub 2] absorption. Three packings of differing specific surface areas were studied, with areas ranging from 656 to 2952 m[sub 2]/m[sub 3]. Liquid flow rates to 36 kg/s*m[sub 2], gas flow rate to 2.2 kg/s*m[sub 2], and gravitational fields to 300 g were covered in this study.

  20. Reed-Solomon error-correction as a software patch mechanism.

    Energy Technology Data Exchange (ETDEWEB)

    Pendley, Kevin D. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States)

    2013-11-01

    This report explores how error-correction data generated by a Reed-Solomon code may be used as a mechanism to apply changes to an existing installed codebase. Using the Reed-Solomon code to generate error-correction data for a changed or updated codebase will allow the error-correction data to be applied to an existing codebase to both validate and introduce changes or updates from some upstream source to the existing installed codebase.

  1. Influence of turbulence on bed load sediment transport

    DEFF Research Database (Denmark)

    Sumer, B. Mutlu; Chua, L.; Cheng, N. S.

    2003-01-01

    -bed experiments and the ripple-covered-bed experiments. In the former case, the flow in the presence of the turbulence generator was adjusted so that the mean bed shear stress was the same as in the case without the turbulence generator in order to single out the effect of the external turbulence on the sediment...

  2. Engine Cycle Analysis of Air Breathing Microwave Rocket with Reed Valves

    Science.gov (United States)

    Fukunari, Masafumi; Komatsu, Reiji; Yamaguchi, Toshikazu; Komurasaki, Kimiya; Arakawa, Yoshihiro; Katsurayama, Hiroshi

    2011-11-01

    The Microwave Rocket is a candidate for a low cost launcher system. Pulsed plasma generated by a high power millimeter wave beam drives a blast wave, and a vehicle acquires impulsive thrust by exhausting the blast wave. The thrust generation process of the Microwave Rocket is similar to a pulse detonation engine. In order to enhance the performance of its air refreshment, the air-breathing mechanism using reed valves is under development. Ambient air is taken to the thruster through reed valves. Reed valves are closed while the inside pressure is high enough. After the time when the shock wave exhausts at the open end, an expansion wave is driven and propagates to the thrust-wall. The reed valve is opened by the negative gauge pressure induced by the expansion wave and its reflection wave. In these processes, the pressure oscillation is important parameter. In this paper, the pressure oscillation in the thruster was calculated by CFD combined with the flux through from reed valves, which is estimated analytically. As a result, the air-breathing performance is evaluated using Partial Filling Rate (PFR), the ratio of thruster length to diameter L/D, and ratio of opening area of reed valves to superficial area α. An engine cycle and predicted thrust was explained.

  3. Variability of bed mobility in natural, gravel-bed channels and adjustments to sediment load at local and reach scales

    Science.gov (United States)

    Thomas E. Lisle; Jonathan M. Nelson; John Pitlick; Mary Ann Madej; Brent L. Barkett

    2000-01-01

    Abstract - Local variations in boundary shear stress acting on bed-surface particles control patterns of bed load transport and channel evolution during varying stream discharges. At the reach scale a channel adjusts to imposed water and sediment supply through mutual interactions among channel form, local grain size, and local flow dynamics that govern bed mobility...

  4. Integrated non-food concept of rape seed, reed canary grass and flax processing for fiber, fuel oil and solid fuel

    International Nuclear Information System (INIS)

    Sipilae, K.

    1998-01-01

    The target of the project was to investigate if rape seed based fuel oil and diesel fuel component, agrofiber and solid fuel from other annual crops could be produced effectively as an alternative to existing non-economical biodiesel-RME and ethanol production. Without heavy tax incentives the biodiesel and grain ethanol can not compete with conventional liquid fuels, the present EU fuel tax legislation will not permit any permanent tax incentives for commercial scale operations. Based on several studies by VTT the rape seed oil will be 30 % cheaper than RME and the utilization as a component 10-30 % blended to heating oil or diesel fuel might the most flexible solution. Neste Oy has carried out the combustion tests with 20 kW boiler and VTT the diesel engine tests with 20 % unprocessed rape seed oil mixtures, the oil was delivered by Mildola Oy. For the co-utilization of annual crops and straw, several laboratory scale combustion and flash pyrolysis tests have been carried out by VTT with straw, reed canary grass etc. In fluid bed combustion 10-30 % addition of rape seed straw and reed canary grass, which have high ash melting point, seems to be less problematic compared to other straw species, which are used for example in Denmark. In a flash pyrolysis process, the alkalies will remain in the char and a low alkali level bio oils can be produced. As a final step in order to reach the zero subsidy target, an extensive laboratory work is carried out to produce agro fibre from flax, reed canary grass and wheat straw. The laboratory results show that a good quality pulp can be produced to be mixed with conventional wood fibres, the quality of flax pulp is even better compared to conventional pulp. During the next months an overall economic calculations will be carried out in Finnish, Danish and Italian conditions as an EU-Apas project in order to see the competitiveness of such integrated concepts to conventional RME and reed canary grass combustion. (orig.)

  5. The role of velocity, pressure, and bed stress fluctuations in bed load transport over bed forms: numerical simulation downstream of a backward-facing step

    Directory of Open Access Journals (Sweden)

    M. W. Schmeeckle

    2015-02-01

    Full Text Available Bed load transport over ripples and dunes in rivers exhibits strong spatial and temporal variability due to the complex turbulence field caused by flow separation at bedform crests. A turbulence-resolving flow model downstream of a backward-facing step, coupled with a model integrating the equations of motion of individual sand grains, is used to investigate the physical interaction between bed load motion and turbulence downstream of separated flow. Large bed load transport events are found to correspond to low-frequency positive pressure fluctuations. Episodic penetration of fluid into the bed increases the bed stress and moves grains. Fluid penetration events are larger in magnitude near the point of reattachment than farther downstream. Models of bed load transport over ripples and dunes must incorporate the effects of these penetration events of high stress and sediment flux.

  6. The role of velocity, pressure, and bed stress fluctuations in bed load transport over bed forms: numerical simulation downstream of a backward-facing step

    Science.gov (United States)

    Schmeeckle, M. W.

    2015-02-01

    Bed load transport over ripples and dunes in rivers exhibits strong spatial and temporal variability due to the complex turbulence field caused by flow separation at bedform crests. A turbulence-resolving flow model downstream of a backward-facing step, coupled with a model integrating the equations of motion of individual sand grains, is used to investigate the physical interaction between bed load motion and turbulence downstream of separated flow. Large bed load transport events are found to correspond to low-frequency positive pressure fluctuations. Episodic penetration of fluid into the bed increases the bed stress and moves grains. Fluid penetration events are larger in magnitude near the point of reattachment than farther downstream. Models of bed load transport over ripples and dunes must incorporate the effects of these penetration events of high stress and sediment flux.

  7. Efficiency of a Horizontal Sub-Surface Flow Constructed Wetland Treatment System in an Arid Area

    Directory of Open Access Journals (Sweden)

    Abeer Albalawneh

    2016-02-01

    Full Text Available The main objective of this study was to evaluate the performance and treatment efficiency of the Horizontal Sub-Surface Flow Constructed Wetland treatment system (HSF-CW in an arid climate. Seventeen sub-surface, horizontal-flow HSF-CW units have been operated for approximately three years to improve the quality of partially-treated municipal wastewater. The studied design parameters included two sizes of volcanic tuff media (i.e., fine or coarse, two different bed dimensions (i.e., long and short, and three plantation types (i.e., reed, kenaf, or no vegetation as a control. The effluent Biological Oxygen Demand (BOD5, Chemical Oxygen Demand (COD, Total Suspended Solid (TSS, and phosphorus from all of the treatments were significantly lower as compared to the influent and demonstrated a removal efficiency of 55%, 51%, 67%, and 55%, respectively. There were significant increases in Electrical Conductivity (EC, sulfate, and calcium in the effluent of most HSF-CWs due to evaporative concentration and mineral dissolution from the media. The study suggests that unplanted beds with either fine or coarse media are the most suitable combinations among all of the studied designs based on their treatment efficiency and less water loss in arid conditions.

  8. Bed-load transportmeter for find sand "Sphinx"

    NARCIS (Netherlands)

    Vinckers, J.B.; Bijker, E.W.; Schijf, J.B.

    1953-01-01

    A new bed-load transportmeter has been designed particularly for very fine bed material (below 400 micron). The basic conception is the same as for the so-called Delft-bottle used for measuring transport by turbulent suspension. The instrument is of the flow-through type. The flow enters through a

  9. Classification and Monitoring of Reed Belts Using Dual-Polarimetric TerraSAR-X Time Series

    Directory of Open Access Journals (Sweden)

    Iris Heine

    2016-06-01

    Full Text Available Synthetic aperture radar polarimetry (PolSAR and polarimetric decomposition techniques have proven to be useful tools for wetland mapping. In this study we classify reed belts and monitor their phenological changes at a natural lake in northeastern Germany using dual-co-polarized (HH, VV TerraSAR-X time series. The time series comprises 19 images, acquired between August 2014 and May 2015, in ascending and descending orbit. We calculated different polarimetric indices using the HH and VV intensities, the dual-polarimetric coherency matrix including dominant and mean alpha scattering angles, and entropy and anisotropy (normalized eigenvalue difference as well as combinations of entropy and anisotropy for the analysis of the scattering scenarios. The image classifications were performed with the random forest classifier and validated with high-resolution digital orthophotos. The time series analysis of the reed belts revealed significant seasonal changes for the double-bounce–sensitive parameters (intensity ratio HH/VV and intensity difference HH-VV, the co-polarimetric coherence phase and the dominant and mean alpha scattering angles and in the dual-polarimetric coherence (amplitude, anisotropy, entropy, and anisotropy-entropy combinations; whereas in summer dense leaves cause volume scattering, in winter, after leaves have fallen, the reed stems cause predominately double-bounce scattering. Our study showed that the five most important parameters for the classification of reed are the intensity difference HH-VV, the mean alpha scattering angle, intensity ratio HH/VV, and the coherence (phase. Due to the better separation of reed and other vegetation (deciduous forest, coniferous forest, meadow, winter acquisitions are preferred for the mapping of reed. Multi-temporal stacks of winter images performed better than summer ones. The combination of ascending and descending images also improved the result as it reduces the influence of the sensor

  10. Economic and financial analysis of harvesting and utilization of river reed in the Okavango Delta, Botswana.

    Science.gov (United States)

    Mmopelwa, G

    2006-06-01

    The Okavango Delta, the largest Ramsar wetland site, is one of the most resource-rich ecosystems in Botswana. A range of resources, including reeds, contribute in various ways to the well-being of many of the communities through subsistence and income generation. The economic value of reeds and other resources found in wetlands has been poorly understood, leading to the perception that wetlands are wastelands, and have little or no economic values. Such resources are therefore likely to receive lower priority in conservation when evaluated against other alternative activities. The aim of this research was to determine the benefit and financial and economic viability of harvesting river reed in the Okavango Delta. Primary data were collected through a structured questionnaire administered at three villages in the Okavango Delta. Secondary data were collected from existing literature. Financial and economic analysis was undertaken using static and financial models. Market prices were used to calculate the net income generated from the sale of harvested reed. The measurement criteria for static models were the annual net cash income, net annual economic benefit, and return on investment (ROI), while those under the dynamic models were the net present value (NPV), benefit cost ratio (BCR), and the net benefit investment (N/K) ratio. It was more financially profitable and economically viable to harvest and sell reeds at Shorobe village (a village relatively close to the District economic centre, Maun), than Shakawe or Etsha-13.

  11. Resistance strategies of Phragmites australis (common reed to Pb pollution in flood and drought conditions

    Directory of Open Access Journals (Sweden)

    Na Zhang

    2018-01-01

    Full Text Available Resistance strategies of clonal organs, and parent and offspring shoots of Phragmites australis (common reed to heavy metal pollution in soils are not well known. To clarify the tolerance or resistance strategies in reeds, we conducted a pot experiment with five levels of Pb concentration (0∼4,500 mg kg−1 in flood and drought conditions. Lead toxicity had no inhibitory effect on the number of offspring shoots in flood environment; however, biomass accumulation, and photosynthetic and clonal growth parameters were inhibited in both water environment. At each treatment of Pb concentration, offspring shoots had greater biomass and higher photosynthesis indicators than parent shoots. The lowest Pb allocation was found in rhizomes. More of the Pb transported to above-ground parts tended to accumulate in parent shoots rather than in offspring shoots. Biomass and photosynthesis of offspring shoots, rhizome length, and the number of buds, rhizomes and offspring shoots in the flooded treatment were significantly greater than those in the drought treatment. Our results indicated that the tolerance strategies used by reeds, including higher biomass accumulation and photosynthesis in offspring shoots, low allocation of Pb in rhizomes and offspring shoots, and stable clonal growth, maintained the stability of population propagation and productivity, improving the resistance of reeds to Pb pollution in flood environment. However, the resistance or tolerance was significantly reduced by the synergistic effect of Pb and drought, which significantly inhibited biomass accumulation, photosynthesis, and clonal growth of reeds.

  12. CHARACTERISTICS OF REED BRIQUETTES – BIOMASS RENEWABLE RESOURCE OF THE DANUBE DELTA

    Directory of Open Access Journals (Sweden)

    Dumitru LICA

    2012-03-01

    Full Text Available The paper presents the most important physical - mechanical properties of the briquettes made of reed biomass after chopping it into chips of 5-30mm length and 0.2-0.6 mm thickness. Both study on the density of the briquettes – as a physical property – and study on their perpendicular compression strength – as a mechanical characteristic – are imposed by the factthat these two characteristics show the compressinggrade of the chips and in the same time their compaction status. The experimental determination of the calorific power and the obtained results are also presented in the paper and compared with values obtained for themost used species of wood waste for briquettes so far (beech and pine wood. The experimental work is done at the laboratory level in the infrastructure of Wood Engineering Faculty. The novelty of the research is that reed biomass from Danube Delta is not exploited nowadays, being an important renewable resource Romania has and could use for heating purpose. The conclusion of the paper is the good result obtained for reed briquettes that have a value of the density very close to that of beech wood. It can be said also that good results were obtained for calorific power of the reed briquettes compared with those made of wood species as beech and pine wood. Reed is an important renewable resource in Danube Delta, unexploited so far, a possible biomass for energy purpose, which can bring a new sector of industrialization.

  13. NRC [Nuclear Regulatory Commission] staff evaluation of the General Electric Company Nuclear Reactor Study (''Reed Report'')

    International Nuclear Information System (INIS)

    1987-07-01

    In 1975, the General Electric Company (GE) published a Nuclear Reactor Study, also referred to as ''the Reed Report,'' an internal product-improvement study. GE considered the document ''proprietary'' and thus, under the regulations of the Nuclear Regulatory Commission (NRC), exempt from mandatory public disclosure. Nonetheless, members of the NRC staff reviewed the document in 1976 and determined that it did not raise any significant new safety issues. The staff also reached the same conclusion in subsequent reviews. However, in response to recent inquiries about the report, the staff reevaluated the Reed Report from a 1987 perspective. This re-evaluation, documented in this staff report, concluded that: (1) there are no issues raised in the Reed Report that support a need to curtail the operation of any GE boiling water reactor (BWR); (2) there are no new safety issues raised in the Reed Report of which the staff was unaware; and (3) although certain issues addressed by the Reed Report are still being studied by the NRC and the industry, there is no basis for suspending licensing and operation of GE BWR plants while these issues are being resolved

  14. Position indicating systems and reed contact unit assemblies for such systems

    International Nuclear Information System (INIS)

    Foxworthy, M.K.

    1980-01-01

    Specifications are given for a position indicating system for determining the position of a movable member inside a sealed container such as the position of a control rod in a nuclear reactor. The system comprises a magnetic flux producing member mounted to the movable member so as to move with it, a series of magnetic reed contact units mounted along the outside of the sealed container to be individually actuated by the flux producer as the movable member moves within the sealed container to indicate the position of this member. Each of the reed contact units is connected to a source of alternating electric current to produce a magnetic flux field to minimize the flux differential between the actuated and unactuated reed contact positions. A second aspect of the invention provides for a low operating flux differential reed contact unit assembly for a position indicating system such that it is actuated by the magnetic member at one magnetic flux level and deactivated at a second level. There is a source of alternating current connected to a coil surrounding the reed contact unit so as to produce an alternating magnetic flux with amplitude less than the difference between the two levels. Variations are given, also diagrams and benefits. (U.K.)

  15. Floodplain inundation response to climate, valley form, and flow regulation on a gravel-bed river in a Mediterranean-climate region

    Science.gov (United States)

    Cienciala, P.; Pasternack, G. B.

    2017-04-01

    Floodplain inundation regime defines hydrological connectivity between river channel and floodplain and thus strongly controls structure and function of these highly diverse and productive ecosystems. We combined an extensive LiDAR data set on topography and vegetation, long-term hydrological records, as well as the outputs of hydrological and two-dimensional hydraulic models to examine how floodplain inundation regimes in a dynamic, regulated, gravel-cobble river in a Mediterranean-climate region are controlled by reach-scale valley morphology, hydroclimatic conditions, and flow regulation. Estimated relative differences in the extent, duration, and cumulative duration of inundation events were often as large as an order of magnitude and generally greatest for large and long duration events. The relative impact of flow regulation was greatest under dry hydroclimatic conditions. Although the effects of hydroclimate and flow impairment are larger than that of valley floor topography, the latter controls sensitivity of floodplain hydroperiod to flow regime changes and should not be ignored. These quantitative estimates of the relative importance of factors that control floodplain processes in Mediterranean, semiarid rivers contributes to better understanding of hydrology and geomorphology of this important class of channels. We also discuss implications of our findings for processes that shape floodplain habitat for riparian vegetation and salmonid fish, especially in the context of ecological restoration.

  16. Fluidized bed adsorption of cephalosporin C.

    Science.gov (United States)

    Hicketier, M; Buchholz, K

    2002-02-28

    Fluidized bed adsorption can substantially simplify the recovery of products from fermentation. There are, however, several critical parameters, which have a significant influence on the performance of such systems. This paper presents experimental results on the adsorption of an antibiotic, Cephalosporin C, on macroporous adsorbents of the polystyrene type and on an ion exchanger. Internals (static mixers) were used to control bed expansion and mixing, the range of flow rates could thus be extended significantly. An integrated mathematical model was developed comprising bed expansion, residence time distribution and mixing, adsorption kinetics and equilibria.

  17. Flow

    DEFF Research Database (Denmark)

    Knoop, Hans Henrik

    2006-01-01

    FLOW. Orden i hovedet på den fede måde Oplevelsesmæssigt er flow-tilstanden kendetegnet ved at man er fuldstændig involveret, fokuseret og koncentreret; at man oplever stor indre klarhed ved at vide hvad der skal gøres, og i hvilket omfang det lykkes; at man ved at det er muligt at løse opgaven...

  18. Using aerial photography for mapping giant reed infestations along the Texas-Mexico portion of the Rio Grande.

    Science.gov (United States)

    Giant reed (Arundo donax L.) is an invasive weed throughout the southern half of the United States with the densest stands growing along the coastal rivers of southern California and the Rio Grande in Texas. The objective of this study was to use aerial photography to map giant reed infestations and...

  19. Mapping giant reed (Arundo donax) infestations along the Texas-Mexico portion of the Rio Grande using aerial photography

    Science.gov (United States)

    Giant reed is an invasive weed throughout the southern half of the United States with the densest stands growing along the coastal rivers of southern California and the Rio Grande in Texas. The objective of this study was to use aerial photography to map giant reed infestations and estimate infested...

  20. Pretreatment of Reed by Wet Oxidation and Subsequent Utilization of the Pretreated Fibers for Ethanol Production

    DEFF Research Database (Denmark)

    Szijarto, Nora; Kádár, Zsófia; Varga, Eniko

    2009-01-01

    lignocelluloses usually do. In the present study, wet oxidation was investigated as the pretreatment method to enhance the enzymatic digestibility of reed cellulose to soluble sugars and thus improve the convertibility of reed to ethanol. The most effective treatment increased the digestibility of reed cellulose...... by cellulases more than three times compared to the untreated control. During this wet oxidation, 51.7% of the hemicellulose and 58.3% of the lignin were solubilized, whereas 87.1% of the cellulose remained in the solids. After enzymatic hydrolysis of pretreated fibers from the same treatment, the conversion...... of cellulose to glucose was 82.4%. Simultaneous saccharification and fermentation of pretreated solids resulted in a final ethanol concentration as high as 8.7 g/L, yielding 73% of the theoretical....

  1. Systematic Procedure for Integrated Process Operation: Reverse Electro-Enhanced Dialysis (REED) during Lactic Acid Fermentation

    DEFF Research Database (Denmark)

    Prado Rubio, Oscar Andres; Jørgensen, Sten Bay; Jonsson, Gunnar Eigil

    2011-01-01

    structure in the REED module. The integrated system design and operation is investigated through batch production of a starter culture. Substantial productivity improvements are predicted using the REED process compared to other systems. Insights are obtained for improving the integrated design......The integration of lactic acid fermentation and Reverse Electro-Enhanced Dialysis (REED) is investigated based upon previously developed mathematical models. A goal driven process and operation design procedure is proposed and partially investigated. The conceptual analysis of the processes...... integration shows the need for an additional pH controller in the fermenten A PI controller is implemented and tested. The complete control structure for the integrated system consists of this PI controller in the fermenter plus a previously developed (Prado-Rubio et al., 2010) input resetting control...

  2. The mechanical spectra of deposited materials by a composite reed vibration method

    International Nuclear Information System (INIS)

    Ying, X.N.; Zhang, L.; Yuan, Y.H.

    2010-01-01

    Recently a composite reed vibration method has been designed to measure the mechanical spectra (complex Young's modulus) of materials from liquid to solid state. The mechanical spectra of materials can be obtained from a composite system consisting of a substrate reed and of materials deposited on it. In this report, two sets of formulas to calculate the mechanical spectra of deposited materials are further analyzed. The proof is given for the previous named 'approximate formulas' (labeled as Formula II). Then the composite reed vibration method can be safely used as an extension of the mechanical spectrum method of the thin solid film. At the same time, some comments are made on previous analytical formulas (labeled as Formula I). At last, more experiments with a small amount of deposited materials are performed. It is found that smaller quantity is more favorable to achieve the intrinsic mechanical spectra of deposited materials.

  3. The Influence of Flow and Bed Slope on Gas Transfer in Steep Streams and Their Implications for Evasion of CO2

    Science.gov (United States)

    Maurice, L.; Rawlins, B. G.; Farr, G.; Bell, R.; Gooddy, D. C.

    2017-11-01

    The evasion of greenhouse gases (including CO2, CH4, and N2O) from streams and rivers to the atmosphere is an important process in global biogeochemical cycles, but our understanding of gas transfer in steep (>10%) streams, and under varying flows, is limited. We investigated gas transfer using combined tracer injections of SF6 and salt. We used a novel experimental design in which we compared four very steep (18.4-29.4%) and four moderately steep (3.7-7.6%) streams and conducted tests in each stream under low flow conditions and during a high-discharge event. Most dissolved gas evaded over short distances ( 100 and 200-400 m, respectively), so accurate estimates of evasion fluxes will require sampling of dissolved gases at these scales to account for local sources. We calculated CO2 gas transfer coefficients (KCO2) and found statistically significant differences between larger KCO2 values for steeper (mean 0.465 min-1) streams compared to those with shallower slopes (mean 0.109 min-1). Variations in flow had an even greater influence. KCO2 was substantially larger under high (mean 0.497 min-1) compared to low flow conditions (mean 0.077 min-1). We developed a statistical model to predict KCO2 using values of streambed slope × discharge which accounted for 94% of the variation. We show that two models using slope and velocity developed by Raymond et al. (2012) for streams and rivers with shallower slopes also provide reasonable estimates of our CO2 gas transfer velocities (kCO2; m d-1). We developed a robust field protocol which could be applied in future studies.

  4. Pacemaker reed switch behavior in 0.5, 1.5, and 3.0 Tesla magnetic resonance imaging units: are reed switches always closed in strong magnetic fields?

    Science.gov (United States)

    Luechinger, Roger; Duru, Firat; Zeijlemaker, Volkert A; Scheidegger, Markus B; Boesiger, Peter; Candinas, Reto

    2002-10-01

    MRI is established as an important diagnostic tool in medicine. However, the presence of a cardiac pacemaker is usually regarded as a contraindication for MRI due to safety reasons. The aim of this study was to investigate the state of a pacemaker reed switch in different orientations and positions in the main magnetic field of 0.5-, 1.5-, and 3.0-T MRI scanners. Reed switches used in current pacemakers and ICDs were tested in 0.5-, 1.5-, and 3.0-T MRI scanners. The closure of isolated reed switches was evaluated for different orientations and positions relative to the main magnetic field. The field strengths to close and open the reed switch and the orientation dependency of the closed state inside the main magnetic field were investigated. The measurements were repeated using two intact pacemakers to evaluate the potential influence of the other magnetic components, like the battery. If the reed switches were oriented parallel to the magnetic fields, they closed at 1.0 +/- 0.2 mT and opened at 0.7 +/- 0.2 mT. Two different reed switch behaviors were observed at different magnetic field strengths. In low magnetic fields ( 200 mT), the reed switches opened in 50% of all tested orientations. No difference between the three scanners could be demonstrated. The reed switches showed the same behavior whether they were isolated or an integral part of the pacemakers. The reed switch in a pacemaker or an ICD does not necessarily remain closed in strong magnetic fields at 0.5, 1.5, or 3.0 T and the state of the reed switch may not be predictable with certainty in clinical situations.

  5. Experimental and numerical study of spouted bed fluif dynamics

    Directory of Open Access Journals (Sweden)

    C. R. Duarte

    2008-03-01

    Full Text Available Spouted beds, originally invented in Canada by Mathur and Gishler (1955 as an alternative to fluidized beds for handling coarse particles, are now widely studied in a variety of physical operations, such as drying, coating and granulation. In this work the particle velocity, minimum spouting flow rate and characteristic fluid-dynamic curves of the spouted bed were obtained using a Eulerian granular multiphase model. The computational work was significantly reduced for axisymmetric gas-solid flows. The experimental data obtained in two spouted bed configurations, conical-cylindrical and two-dimensional, were compared with the simulated results, showing good agreement

  6. A three-dimensional simulation of gas/particle flow and ozone decomposition in the riser of a circulating fluidized bed

    DEFF Research Database (Denmark)

    Hansen, Kim Granly; Solberg, Tron; Hjertager, Bjørn Helge

    2004-01-01

    concentration in the 10.85 m high riser by the use of a UV detector system. Furthermore a pressure drop profile was reported. Comparison between measured and simulated time averaged ozone concentration at different elevations in the riser shows good agreement. The 3D representation of the reactor geometry gives......The isothermal decomposition of ozone has been implemented in the CFD code FLOTRACS-MP-3D. The code is a 3D multiphase computational fluid dynamics code with an Eulerian description of both gas and particle phase. The turbulent motion of the particulate phase is modeled using the kinetic theory...... for granular flow, and the gas phase turbulence is modeled using a Sub-Grid-Scale model, cf. Ibsen et al. (2001). The decomposition reaction is studied in a 3D representation of a 0.254 m i.d. riser, which has been studied experimentally by Ouyang et al. (1993). The authors obtained profiles of ozone...

  7. Fluid-bed combustion

    Energy Technology Data Exchange (ETDEWEB)

    Hunt, G.; Schoebotham, N.

    1981-02-01

    In Energy Equipment Company's two-stage fluidized bed system, partial combustion in a fluidized bed is followed by burn-off of the generated gases above the bed. The system can be retrofitted to existing boilers, and can burn small, high ash coal efficiently. It has advantages when used as a hot gas generator for process drying. Tests on a boiler at a Cadbury Schweppes plant are reported.

  8. Coolability of volumetrically heated particle beds

    Energy Technology Data Exchange (ETDEWEB)

    Rashid, Muhammad

    2017-03-22

    In case of a severe nuclear reactor accident, with loss of coolant, a particle bed may be formed from the fragmentation of the molten core in the residual water at different stages of the accident. To avoid further propagation of the accident and maintain the integrity of the reactor pressure vessel, the decay heat of the particle bed must be removed. To better understand the various thermo-hydraulic processes within such heat-generating particle beds, the existing DEBRIS test facility at IKE has been modified to be able to perform novel boiling, dryout and quenching experiments. The essential experimental data includes the pressure gradients measured by 8 differential pressure transducers along the bed height as a function of liquid and vapour superficial velocities, the determination of local dryout heat fluxes for different system pressures as well as the local temperature distribution measured by a set of 51 thermocouples installed inside the particle bed. The experiments were carried out for two different particle beds: a polydispersed particle bed which consisted of stainless steel balls (2 mm, 3 mm and 6 mm diameters) and an irregular particle bed which consisted of a mixture of steel balls (3 mm and 6 mm) and irregularly shaped Al{sub 2}O{sub 3} particles. Additionally, all experiments were carried out for different flow conditions, such as the reference case of passive 1D top-flooding, 1D bottom flooding (driven by external pumps and different downcomer configurations) and 2D top-/bottom-/lateral flooding with a perforated downcomer. In this work, it has been observed that for both particle beds with downcomer configurations an open downcomer leads to the best coolability (dryout heat flux = 1560 kW/m{sup 2}, polydispersed particle bed, psys = 1 bar) of the particle bed, mainly due to bottom-flow with enhanced natural convection. It has also been shown that a potential lateral flow via a perforation of the downcomer does not bring any further improvements

  9. In-bed accountability of tritium in production scale metal hydride storage beds

    International Nuclear Information System (INIS)

    Klein, J.E.

    1995-01-01

    An ''in-bed accountability'' (IBA) flowing gas calorimetric measurement method has been developed and implemented to eliminate the need to remove tritium from production scale metal hydride storage beds for inventory measurement purposes. Six-point tritium IBA calibration curves have been completed for two, 390 gram tritium metal hydride storage beds. The calibration curves for the two tritium beds are similar to those obtained from the ''cold'' test program. Tritium inventory errors at the 95 percent confidence level ranged from ± 7.3 to 8.6 grams for the cold test results compared to ± 4.2 to 7.5 grams obtained for the two tritium calibrated beds

  10. Synthesis of MCM-41 nanoparticles from stem of common reed ash ...

    Indian Academy of Sciences (India)

    45

    SiO2 powder was extracted from stem of common reed ash as silica source. CTAB, graphite powder, nickel chloride, methanol, paraffin, ammonium hydroxide and sodium hydroxide were purchased from Merck. The chemical composition of the SCRA was analyzed by X-ray fluorescence spectroscopy. (XRF, 8410 Rh 60 kV) ...

  11. Is shared male assistance with antiparasitic nest defence costly in the polygynous great reed warbler?

    Czech Academy of Sciences Publication Activity Database

    Požgayová, Milica; Procházka, Petr; Honza, Marcel

    2013-01-01

    Roč. 85, č. 3 (2013), s. 615-621 ISSN 0003-3472 R&D Projects: GA AV ČR IAA600930605; GA AV ČR IAA600930903 Institutional support: RVO:68081766 Keywords : great reed warbler * aggressive behaviour * brood parasitism * common cuckoo * mating status Subject RIV: EG - Zoology Impact factor: 3.068, year: 2013

  12. Using aerial photography and image analysis to measure changes in giant reed populations

    Science.gov (United States)

    A study was conducted along the Rio Grande in southwest Texas to evaluate color-infrared aerial photography combined with supervised image analysis to quantify changes in giant reed (Arundo donax L.) populations over a 6-year period. Aerial photographs from 2002 and 2008 of the same seven study site...

  13. Indexes of the common reed's seed vitality from water-bodies of the Chernobyl exclusive zone

    International Nuclear Information System (INIS)

    Yavnuk, A.A.; Shevtsova, N.L.; Gudkov, D.I.; Levchenko, Ya.I.

    2010-01-01

    Investigation of the common reed's seed vitality (vegetation of 2009) from flood-plain water-bodies with different level of radionuclide contamination was carried out. Decrease in indexes of seed's vitality and abnormalities in seed dynamic sprouting was noticed. Dose-response relationship of germination, germinating force, survival rate of seeds of plants was determined. (authors)

  14. Cryptic species of sharp-nosed reed frogs in the Hyperolius nasutus ...

    African Journals Online (AJOL)

    The sharp-nosed reed frog is widespread in Africa. Although currently recognized as one species, suggestions have been made that more than one species might exist. We analysed 237 calls of 69 males from 19 localities in the western to southern parts of Africa. Calls fall into three groups, which we recognize as cryptic ...

  15. PROJECT RE-ED, A DEMONSTRATION PROJECT FOR THE REEDUCATION OF EMOTIONALLY DISTURBED CHILDREN.

    Science.gov (United States)

    North Carolina State Dept. of Mental Health, Raleigh.

    THE PROJECT FOR THE REEDUCATION OF EMOTIONALLY DISTURBED CHILDREN (PROJECT RE-ED), A DEMONSTRATION PROJECT (1961-1968) TO DEVELOP AND EVALUATE THE EFFECTIVENESS OF RESIDENTIAL SCHOOLS (SUNDAY THROUGH FRIDAY) FOR DISTURBED CHILDREN, IS DESCRIBED. THE PROFESSIONAL TRAINING AT GEORGE PEABODY COLLEGE, TENNESSEE, AND USE OF CAREFULLY SELECTED…

  16. Dilute oxalic acid pretreatment for biorefining giant reed (Arundo donax L.)

    Science.gov (United States)

    Danilo Scordia; Salvatore L. Cosentino; Jae-Won Lee; Thomas W. Jeffries

    2011-01-01

    Biomass pretreatment is essential to overcome recalcitrance of lignocellulose for ethanol production. In the present study we pretreated giant reed (Arundo donax L.), a perennial, rhizomatous lignocellulosic grass with dilute oxalic acid. The effects of temperature (170-190 ºC), acid loading (2-10% w/w) and reaction time (15-40 min) were handled as a single...

  17. Analisa Kinerja Pengkodean Kanal Type Reed Solomon Coding pada Kualitas Transmisi Citra

    Directory of Open Access Journals (Sweden)

    Baharuddin

    2018-03-01

    Full Text Available Dalam sistem telekomunikasi, data multimedia berupa audio, citra, dan video ditransmisikan ke penerima melalui sebuah kanal komunikasi. Pada sistem telekomunikasi yang menggunakan kanal komunikasi wireless, selain pengaruh redaman, gangguan yang paling dominan adalah noise dan fading. Fading dan noise dikanal akan menurunkan kinerja sistem telekomunikasi digital karena dapat menyebabkan terjadinya kesalahan pendeteksian sinyal, sehingga terjadi perubahan bit atau simbol pada sisi penerima. Dengan menerapkan teknik pengkodean kanal tipe Reed Solomon Code pada sisi pengirim dan penerima, maka dapat ditingkatkan kinerja dari sistem komunikasi digital tersebut. Melalui simulasi dalam penelitian ini, telah dianalisa pengaruh penerapan teknik pengkodean kanal Reed Solomon Code pada sistem yang dipengaruhi noise Additive White Gaussian Noise (AWGN dan fading Rayleigh. Besarnya pengaruh penggunaan dari teknik pengkodean kanal Reed Solomon Code dapat diketahui melalui analisa Bit Error Rate (BER dan Peak Signal to Noise Ratio (PSNR. Hasil simulasi dari penelitian ini menunjukkan bahwa adanya peningkatan perbaikan sistem dipenerima rata-rata 5dB bila dibandingkan dengan tanpa menggunakan teknik pengkodean kanal Reed Solomon Code.

  18. Reed Warbler Hosts Fine-Tune their Defenses to Track Three Decades of Cuckoo Decline

    Science.gov (United States)

    Thorogood, Rose; Davies, Nicholas B

    2013-01-01

    Interactions between avian hosts and brood parasites can provide a model for how animals adapt to a changing world. Reed warbler (Acrocephalus scirpaceus) hosts employ costly defenses to combat parasitism by common cuckoos (Cuculus canorus). During the past three decades cuckoos have declined markedly across England, reducing parasitism at our study site (Wicken Fen) from 24% of reed warbler nests in 1985 to 1% in 2012. Here we show with experiments that host mobbing and egg rejection defenses have tracked this decline in local parasitism risk: the proportion of reed warbler pairs mobbing adult cuckoos (assessed by responses to cuckoo mounts and models) has declined from 90% to 38%, and the proportion rejecting nonmimetic cuckoo eggs (assessed by responses to model eggs) has declined from 61% to 11%. This is despite no change in response to other nest enemies or mimetic model eggs. Individual variation in both defenses is predicted by parasitism risk during the host’s egg-laying period. Furthermore, the response of our study population to temporal variation in parasitism risk can also explain spatial variation in egg rejection behavior in other populations across Europe. We suggest that spatial and temporal variation in parasitism risk has led to the evolution of plasticity in reed warbler defenses. PMID:24299407

  19. Pendekodean Kanal Reed Solomon Berbasis FPGA untuk Transmisi Citra pada Sistem Komunikasi Satelit Nano

    Directory of Open Access Journals (Sweden)

    Andi Nurul Utami Husain

    2013-03-01

    Full Text Available Sistem komunikasi satelit saat ini sedang dikembangkan oleh mahasiswa-mahasiswi ITS, salah satunya yaitu Sistem komunikasi satelit nano 2,4 GHz untuk pengiriman citra. Untuk mengatasi kerusakan informasi yang diterima akibat noise selama transmisi, maka di stasiun bumi dibutuhkan pendekodean kanal Reed Solomon (255,239 untuk mendeteki dan mengoreksi informasi jika terjadi kesalahan pada informasinya. Dalam makalah ini bertujuan untuk merancang pendekodean kanal Reed Solomon(255,239 untuk diimplementasikan pada stasiun bumi. Pendekodean ini secara teori mampu mendeteksi dan mengoreksi maksimum 8 simbol error yang terjadi pada informasi. Pendekodean Reed Solomon(255,239 dirancang menggunakan bahasa pemrograman VHDL (VHSIC Hardware Description Language dan dimasukkan kedalam board FPGA (Field-Programmable Gate Array. Pengujiannya dilakukan hanya secara simulasi dengan menginjeksikan error pada data informasi yang diterima oleh Reed Solomon(255,239 karena relatif sulit diuji dengan menambahkan error saat tahap implementasi. Secara simulasi pendekodean ini telah mampu mengoreksi sebanyak 8 simbol error sesuai dengn teori. Pada tahap implementasinya juga telah berhasil karena telah mampu menerima informasi yang sesuai dengan informasi yang dikirim dengan asumsi tidak terdapat error pada informasi.

  20. Leaf composition of American bur-reed (Sparganium americanum Nutt.) to determine pesticide mitigation capability

    Science.gov (United States)

    American bur-reed (Sparganium americanum Nutt.), a common aquatic plant in the middle and eastern United States and Canada, is often located in water-retaining drainage areas. The purpose of this study was to determine the leaf composition of S. americanum, paying attention to the cuticular waxes a...

  1. Effect of reed canary grass cultivation on greenhouse gas emission from peat soil at controlled rewetting

    DEFF Research Database (Denmark)

    Karki, Sandhya; Elsgaard, Lars; Lærke, Poul Erik

    2015-01-01

    Cultivation of bioenergy crops in rewetted peatland (paludiculture) is considered as a possible land use option to mitigate greenhouse gas (GHG) emissions. However, bioenergy crops like reed canary grass (RCG) can have a complex influence on GHG fluxes. Here we determined the effect of RCG...

  2. Research on Noise Reduction of Reed Valves of a Hermetic Refrigerator Compressor

    Science.gov (United States)

    He, Zhilong; Chen, Qian; Li, Dantong; Wang, Ju; Xia, Pu; Wang, Tao

    2017-08-01

    The noise level of the refrigerator compressor has received more and more attention in recent years. As the key component of a compressor, reed valve is its main noise source. In this paper, a new noise reduction technology of coating on reed valve surface is proposed and verified by experiments. Firstly, the reed valves were coated, and their surface characteristics were checked. Then, the refrigerator compressor p-V diagram test was carried out to investigate the influence of doped diamond-like carbon (DLC) coating on power consumption. Finally, the noise test rig for the refrigerator compressor was set up. Based on the standard test method, noise spectrum was measured in a semi-anechoic room under standard working condition. Research results showed that the compressor noise was significantly reduced by 1.8dB (A) after coating. Moreover, the effect of aerodynamic noise reduction at suction side is better than that at discharge side. However, the influence of the film thickness on noise reduction value is little. The COP was reduced by 0.6% as compared to the compressor with uncoated reed valves.

  3. The effect of flooding on the recruitment of reed marsh and tall forb plant species

    NARCIS (Netherlands)

    Lenssen, J.P.M.; Ten Dolle, G.E.; Blom, C.W.P.M.

    1998-01-01

    Recruitment of plant species in wetlands dominated by Phragmites australis often results in a zonation of two vegetation types. A development of reed marshes takes place in the shallow flooded parts where the dominant P. australis becomes accompanied by interstitial marsh species. The vegetation on

  4. Simple Reed-Solomon Forward Error Correction (FEC) Scheme for FECFRAME

    OpenAIRE

    Roca, Vincent; Cunche, Mathieu; Lacan, Jérôme; Bouabdallah, Amine; Matsuzono, Kazuhisa

    2013-01-01

    Internet Engineering Task Force (IETF) Request for Comments 6865; This document describes a fully-specified simple Forward Error Correction (FEC) scheme for Reed-Solomon codes over the finite field (also known as the Galois Field) GF(2^^m), with 2

  5. Oil/water displacement in microfluidic packed beds under weakly water-wetting conditions: competition between precursor film flow and piston-like displacement

    Science.gov (United States)

    Tanino, Yukie; Zacarias-Hernandez, Xanat; Christensen, Magali

    2018-02-01

    Optical microscopy was used to measure depth-averaged oil distribution in a quasi-monolayer of crushed marble packed in a microfluidic channel as it was displaced by water. By calibrating the transmitted light intensity to oil thickness, we account for depth variation in the fluid distribution. Experiments reveal that oil saturation at water breakthrough decreases with increasing Darcy velocity, U_{ {w}}, between capillary numbers {Ca} = μ _{ {w}} U_{ {w}}/σ = 9× 10^{-7} and 9× 10^{-6}, where μ _{ {w}} is the dynamic viscosity of water and σ is the oil/water interfacial tension, under the conditions considered presently. In contrast, end-point (long-time) remaining oil saturation depends only weakly on U_{ {w}}. This transient dependence on velocity is attributed to the competition between precursor film flow, which controls early time invasion dynamics but is inefficient at displacing oil, and piston-like displacement, which controls ultimate oil recovery. These results demonstrate that microfluidic experiments using translucent grains and fluids are a convenient tool for quantitative investigation of sub-resolution liquid/liquid displacement in porous media.

  6. Filter bed systems treating domestic wastewater in the Nordic countries - Performance and reuse of filter media

    DEFF Research Database (Denmark)

    Jenssen, Petter D.; Krogstad, T.; Paruch, A.M.

    2010-01-01

    Nine filter beds have been constructed in the Nordic countries, Denmark, Finland, Norway and Sweden. Filter beds consist of a septic tank followed by an aerobic pre-treatment biofilter and a subsequent saturated flow grass-covered filter. Thus, filter beds are similar to subsurface flow construct...... with phosphorus, the light-weight aggregate, Filtralite®P used in the saturated bed is a suitable phosphorus fertilizer and additionally has a liming effect. © 2010 Elsevier B.V....

  7. Glycoproteomic characterization of carriers of the CD15/Lewisx epitope on Hodgkin's Reed-Sternberg cells

    Directory of Open Access Journals (Sweden)

    Hitchen Paul G

    2011-03-01

    Full Text Available Abstract Background The Lewisx trisaccharide, also referred to as the CD15 antigen, is a diagnostic marker used to distinguish Hodgkin's lymphoma from other lymphocytic cancers. However, the role of such fucosylated structures remains poorly understood, in part because carriers of Lewisx structures on Hodgkin's Reed-Sternberg cells have not been identified. Methods GalMBP, an engineered carbohydrate-recognition protein that binds selectively to oligosaccharides with paired terminal galactose and fucose residues, has been used in conjunction with proteomic and glycomic analysis to identify glycoprotein carriers of Lewisx and related glycan structures in multiple Hodgkin's Reed-Sternberg cell lines. Results Multiple glycoproteins that bind to GalMBP and carry CD15/Lewisx have been identified in a panel of six Reed-Sternberg cell lines. The most commonly identified Lewisx-bearing glycoproteins are CD98hc, which was found in all six cell lines tested, and intercellular adhesion molecule-1 and DEC-205, which were detected in five and four of the lines, respectively. Thus, several of the most prominent cell adhesion molecules on the lymphomas carry this characteristic glycan epitope. In addition, the Hodgkin's Reed-Sternberg cell lines can be grouped into subsets based on the presence or absence of less common Lewisx-bearing glycoproteins. Conclusions CD98 and intercellular adhesion molecule-1 are major carriers of CD15/Lewisx on Reed-Sternberg cells. Binding of DC-SIGN and other glycan-specific receptors to the Lewisx epitopes on CD98 and intercellular adhesion molecule-1 may facilitate interaction of the lymphoma cells with lymphocytes and myeloid cells in lymph nodes.

  8. Experimental Assessment of Recycled Diesel Spill-Contaminated Domestic Wastewater Treated by Reed Beds for Irrigation of Sweet Peppers.

    Science.gov (United States)

    Almuktar, Suhad A A A N; Scholz, Miklas

    2016-02-06

    The aim of this experimental study is to assess if urban wastewater treated by ten different greenhouse-based sustainable wetland systems can be recycled to irrigate Capsicum annuum L. (Sweet Pepper; California Wonder) commercially grown either in compost or sand within a laboratory environment. The design variables were aggregate diameter, contact time, resting time and chemical oxygen demand. The key objectives were to assess: (i) the suitability of different treated (recycled) wastewaters for irrigation; (ii) response of peppers in terms of growth when using recycled wastewater subject to different growth media and hydrocarbon contamination; and (iii) the economic viability of different experimental set-ups in terms of marketable yield. Ortho-phosphate-phosphorus, ammonia-nitrogen, potassium and manganese concentrations in the irrigation water considerably exceeded the corresponding water quality thresholds. A high yield in terms of economic return (marketable yield expressed in monetary value) was linked to raw wastewater and an organic growth medium, while the plants grown in organic medium and wetlands of large aggregate size, high contact and resting times, diesel-spill contamination and low inflow loading rate produced the best fruits in terms of their dimensions and fresh weights, indicating the role of diesel in reducing too high nitrogen concentrations.

  9. Operational strategy, economic and environmental performance of sludge treatment reed bed systems - based on 28 years of experience

    DEFF Research Database (Denmark)

    Nielsen, S.; Larsen, Julie Dam

    2016-01-01

    and hazardous organic compounds, qualities that make it suitable for recycling on agricultural land. The upfront capital cost for STRBs are often higher compared to mechanical dewatering devices. However, the operational expenses (OPEX) (including energy, chemicals, bio solid handling) are significantly lower...... compared to conventional mechanical dewatering devices, delivering an economic break-even of about 3-5 years. This paper provides an overview of the operation and maintenance costs and environmental benefits of a typical STRB based on the experiences gained from the operation of a large number of STRBs...

  10. Fluidized bed incinerator development

    International Nuclear Information System (INIS)

    Ziegler, D.L.; Johnson, A.J.

    1976-01-01

    A fluidized bed incinerator is being developed for burning rad contaminated solid and liquid waste materials. In situ neutralization of acid gases by the bed material, catalytic afterburning, and gas filtration are used to produce a clean flue gas without the use of aqueous scrubbing

  11. Environmental protection stability of river bed and banks using convex, concave, and linear bed sills.

    Science.gov (United States)

    Keshavarzi, Alireza; Noori, Lila Khaje

    2010-12-01

    River bed scourings are a major environmental problem for fish and aquatic habitat resources. In this study, to prevent river bed and banks from scouring, different types of bed sills including convex, concave and linear patterns were installed in a movable channel bed in a laboratory flume. The bed sills were tested with nine different arrangements and under different flow conditions. To find the most effective bed sill pattern, the scouring depth was measured downstream of the bed sill for a long experimental duration. The scour depth was measured at the middle and at the end of each experimental test for different ratios of the arch radius to the channel width [r/w]. The experimental results indicated that the convex pattern with r/w=0.35 produced minimum bed scouring depth at the center line whereas the concave pattern with r/w=0.23 produced the minimum scour depth at the wall banks. Therefore, the convex pattern was the most effective configuration for prevention of scouring at the center line of the river while the concave pattern was very effective to prevent scouring at the river banks. These findings can be suggested to be used in practical applications.

  12. Thermal Analysis of Fluidized Bed and Fixed Bed Latent Heat Thermal Storage System

    Science.gov (United States)

    Beemkumar, N.; Karthikeyan, A.; Shiva Keshava Reddy, Kota; Rajesh, Kona; Anderson, A.

    2017-05-01

    Thermal energy storage technology is essential because its stores available energy at low cost. Objective of the work is to store the thermal energy in a most efficient method. This work is deal with thermal analysis of fluidized bed and fixed bed latent heat thermal storage (LHTS) system with different encapsulation materials (aluminium, brass and copper). D-Mannitol has been used as phase change material (PCM). Encapsulation material which is in orbicular shape with 4 inch diameter and 2 mm thickness orbicular shaped product is used. Therminol-66 is used as a heat transfer fluid (HTF). Arrangement of encapsulation material is done in two ways namely fluidized bed and fixed bed thermal storage system. Comparison was made between the performance of fixed bed and fluidized bed with different encapsulation material. It is observed that from the economical point of view aluminium in fluidized bed LHTS System has highest efficiency than copper and brass. The thermal energy storage system can be analyzed with fixed bed by varying mass flow rate of oil paves a way to find effective heat energy transfer.

  13. Measurement and modeling of bed shear stress under solitary waves

    Digital Repository Service at National Institute of Oceanography (India)

    Jayakumar, S.; Guard, P.A.; Baldock, T.E.

    Direct measurements of bed shear stresses (using a shear cell apparatus) generated by non-breaking solitary waves are presented. The measurements were carried out over a smooth bed in laminar and transitional flow regimes (~ 10 sup (4) < R sub (e...

  14. Incipient motion of gravel and coal beds

    Indian Academy of Sciences (India)

    R. Narasimhan (Krishtel eMaging) 1461 1996 Oct 15 13:05:22

    2Department of Civil Engineering, S R K R Engineering College, Bhimavaram. 534202, India e-mail: sdey@civil.iitkgp.ernet.in. MS received 15 January 2002. Abstract. An experimental study on incipient motion of gravel and coal beds under unidirectional steady-uniform flow is presented. Experiments were carried out in a ...

  15. Live-bed scour experiments with 45 wing-wall abutments

    Indian Academy of Sciences (India)

    Normally, the live-bed scour occurs only during flood flow, and the depth of flow is expected to be high during flood, thus under live-bed scour conditions, the factor, Kh accounting approaching flow depth, may be taken equal to 1. Envelope curve in figure 7 drawn using the experimental data, defines the factor Kd accounting.

  16. Influence of turbulence on bed load sediment transport

    DEFF Research Database (Denmark)

    Sumer, B. Mutlu; Chua, L.; Cheng, N. S.

    2003-01-01

    -bed experiments and the ripple-covered-bed experiments. In the former case, the flow in the presence of the turbulence generator was adjusted so that the mean bed shear stress was the same as in the case without the turbulence generator in order to single out the effect of the external turbulence on the sediment...... transport. In the ripple-covered-bed case, the mean and turbulence quantities of the streamwise component of the velocity were measured, and the Shields parameter, due to skin friction, was determined. The Shields parameter, together with the r.m.s. value of the streamwise velocity fluctuations, were...

  17. Determination of viscosity in recirculating fluidized bed using radioactive tracer

    International Nuclear Information System (INIS)

    Silva, G.G. da.

    1986-01-01

    The use of radioactive tracer for measuring viscosity is proposed. The methodology relates the terminal velocity of a radioactive sphere in interior of fluid with the viscosity, which can be a fluidized bed or total flow of solids. The arrangement is composed by two γ detectors placed externally and along the bed. Both detectors are coupled by amplifier to electronic clock. The drop time of sphere between two detectors is measured. The bed viscosity two detectors is measured. The bed viscosity is calculated from mathematical correlations of terminal velocity of the sphere. (M.C.K.)

  18. Diversification in a biodiversity hot spot: landscape correlates of phylogeographic patterns in the African spotted reed frog.

    Science.gov (United States)

    Lawson, Lucinda P

    2013-04-01

    The Eastern Afromontane Biodiversity Hotspot is known for microendemism and exceptional population genetic structure. The region's landscape heterogeneity is thought to limit gene flow between fragmented populations and create opportunities for regional adaptation, but the processes involved are poorly understood. Using a combination of phylogeographic analyses and circuit theory, I investigate how characteristics of landscape heterogeneity including regional distributions of slope, rivers and streams, habitat and hydrological basins (drainages) impact genetic distance among populations of the endemic spotted reed frog (Hyperolius substriatus), identifying corridors of connectivity as well as barriers to dispersal. Results show that genetic distance among populations is most strongly correlated to regional and local hydrologic structure and the distribution of suitable habitat corridors, not isolation by distance. Contrary to expectations, phylogeographic structure is not coincident with the two montane systems, but instead corresponds to the split between the region's two major hydrological basins (Zambezi and East Central Coastal). This results in a paraphyletic relationship for the Malawian Highlands populations with respect to the Eastern Arc Mountains and implies that the northern Malawian Highlands are the diversity centre for H. substriatus. Although the Malawian Highlands collectively hold the greatest genetic diversity, individual populations have lower diversity than their Eastern Arc counterparts, with an overall pattern of decreasing population diversity from north to south. Through the study of intraspecific differentiation across a mosaic of ecosystem and geographic heterogeneity, we gain insight into the processes of diversification and a broader understanding of the role of landscape in evolution. © 2013 Blackwell Publishing Ltd.

  19. Bed rest during pregnancy

    Science.gov (United States)

    ... Belizán JM, Bergel E. Bed rest in singleton pregnancies for preventing preterm birth. Cochrane Database ... and Gynecology, Loma Linda University School of Medicine, Loma Linda Center for Fertility, ...

  20. Enuresis (Bed-Wetting)

    Science.gov (United States)

    ... Symptoms of enuresis Enuresis is when an older child (age 7 or older) wets the bed at night ... feel guilt and embarrassment. It’s true that your child should take responsibility for bedwetting. He or she could do this ...

  1. Particle fuel bed tests

    International Nuclear Information System (INIS)

    Horn, F.L.; Powell, J.R.; Savino, J.M.

    1985-01-01

    Gas-cooled reactors, using packed beds of small diameter coated fuel particles have been proposed for compact, high-power systems. The particulate fuel used in the tests was 800 microns in diameter, consisting of a thoria kernel coated with 200 microns of pyrocarbon. Typically, the bed of fuel particles was contained in a ceramic cylinder with porous metallic frits at each end. A dc voltage was applied to the metallic frits and the resulting electric current heated the bed. Heat was removed by passing coolant (helium or hydrogen) through the bed. Candidate frit materials, rhenium, nickel, zirconium carbide, and zirconium oxide were unaffected, while tungsten and tungsten-rhenium lost weight and strength. Zirconium-carbide particles were tested at 2000 K in H 2 for 12 hours with no visible reaction or weight loss

  2. Innovative rock bed construction

    Energy Technology Data Exchange (ETDEWEB)

    Cook, J.

    1983-06-01

    A general discussion of the use of rock beds for heating and cooling thermal storage is particularized for design and construction in Phoenix, Arizona. The rock bed parameters for three two-story condominium apartments constructed in 1982 are discussed, including sizing criteria and original construction details. A revised construction method using gabions that are self-supporting chain link cylinders provided a much more economical construction method as well as other advantages of speed and structural flexibility.

  3. General Purpose Graphics Processing Unit Based High-Rate Rice Decompression and Reed-Solomon Decoding

    Energy Technology Data Exchange (ETDEWEB)

    Loughry, Thomas A. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States)

    2015-02-01

    As the volume of data acquired by space-based sensors increases, mission data compression/decompression and forward error correction code processing performance must likewise scale. This competency development effort was explored using the General Purpose Graphics Processing Unit (GPGPU) to accomplish high-rate Rice Decompression and high-rate Reed-Solomon (RS) decoding at the satellite mission ground station. Each algorithm was implemented and benchmarked on a single GPGPU. Distributed processing across one to four GPGPUs was also investigated. The results show that the GPGPU has considerable potential for performing satellite communication Data Signal Processing, with three times or better performance improvements and up to ten times reduction in cost over custom hardware, at least in the case of Rice Decompression and Reed-Solomon Decoding.

  4. Effects of bleaching wastewater irrigation on soil quality of constructed reed wetlands

    Directory of Open Access Journals (Sweden)

    Cheng Ding

    2016-10-01

    Full Text Available Constructed reed wetland microcosms (CRWs in a lab of east China have been irrigated with bleaching wastewater per month for a reed growth season. The soil physicochemical properties, enzyme activities (i.e. urease, invertase, polyphenol oxidase, alkaline phosphatase and cellulase and soil microbial diversity were assayed before and after the exposure experiment. Compared to the river water irrigated controls (CKs, bleaching wastewater application has no marked influence on soil pH, but significantly increased soil Na+, total halogen and absorbable organic halogen (AOX contents, which induced the increasing of soil electrical conductivity. Furthermore, soil enzyme activities displayed significant variation (except for polyphenol oxidase. Bleaching wastewater irrigation decreased Sorenson’s pairwise similarity coefficient (Cs, which indicated the changes of the structure of bacterial and fungal communities. However, only the diversity of bacterial community was inhibited and has no effect on the diversity of fungal community, as evidenced by the calculated Shannon–Wiener index (H.

  5. On locality of Generalized Reed-Muller codes over the broadcast erasure channel

    KAUST Repository

    Alloum, Amira

    2016-07-28

    One to Many communications are expected to be among the killer applications for the currently discussed 5G standard. The usage of coding mechanisms is impacting broadcasting standard quality, as coding is involved at several levels of the stack, and more specifically at the application layer where Rateless, LDPC, Reed Slomon codes and network coding schemes have been extensively studied, optimized and standardized in the past. Beyond reusing, extending or adapting existing application layer packet coding mechanisms based on previous schemes and designed for the foregoing LTE or other broadcasting standards; our purpose is to investigate the use of Generalized Reed Muller codes and the value of their locality property in their progressive decoding for Broadcast/Multicast communication schemes with real time video delivery. Our results are meant to bring insight into the use of locally decodable codes in Broadcasting. © 2016 IEEE.

  6. Analysis of Iterated Hard Decision Decoding of Product Codes with Reed-Solomon Component Codes

    DEFF Research Database (Denmark)

    Justesen, Jørn; Høholdt, Tom

    2007-01-01

    Products of Reed-Solomon codes are important in applications because they offer a combination of large blocks, low decoding complexity, and good performance. A recent result on random graphs can be used to show that with high probability a large number of errors can be corrected by iterating mini...... minimum distance decoding. We present an analysis related to density evolution which gives the exact asymptotic value of the decoding threshold and also provides a closed form approximation to the distribution of errors in each step of the decoding of finite length codes.......Products of Reed-Solomon codes are important in applications because they offer a combination of large blocks, low decoding complexity, and good performance. A recent result on random graphs can be used to show that with high probability a large number of errors can be corrected by iterating...

  7. The role of UV reflection in parasite egg rejection in reed warbler (Acrocephalus scirpaceus)

    OpenAIRE

    Šulc, Michal

    2012-01-01

    One of the best ways how hosts may defend their clutch against brood parasitism is recognition and rejection of parasitic eggs. It has been documented that ability to percept UV light in birds affects their behaviour. By using a spectrophotometer we found that Reed Warbler (Acrocephalus scirpaceus) eggs and Common cuckoo (Cuculus canorus) eggs differ mainly in brightness but also in UV hue. We investigated the influence of birds' UV vision on recognition and rejection of parasitic eggs. There...

  8. The Protective Properties of Common Reed Plantations on Shores of the Lower Volga Region

    Directory of Open Access Journals (Sweden)

    Solodovnikov Denis Anatolyevich

    2014-12-01

    Full Text Available The abrasion processing of shores is a pressing problem of large water basins of the Lower Volga region and other Russian regions. About 3 km2 of shoreland is annually lost in the zone of the Volgograd water basin as a result of this process. The existing methods of shores protection are connected with the creation of concrete structures having a high level of erosion resistance. They are extremely expensive and in most cases they are not affordable for rural municipalities suffering from abrasion. The authors offer cheap and environmentally friendly way of protecting the shores of large water basins from abrasion. The method is based on the plantation of a common reed strip on a water basin’s shallow. The biological characteristics of common reed as the main component of shore protection structures are described. The terms and milestones of the work in the conditions of the Volgograd water basin are developed. The main result of applying our methodology is the complete cessation of abrasion processing of the shore at the corresponding piece of land. The authors overview the positive qualities of reed plantations, their biocenotic, barrier and waterproof role in on-shore ecosystems. The application of the described method will allow saving for the national economy dozens of hectares of valuable shore lands annually, in particular, irrigated cropland, settlement lands, infrastructure. In addition to the direct benefits associated with the conservation of land resources, the intensity of adverse processes associated with erosion of shores (water basin muddying, deterioration of sanitary qualities of water will decrease. Due to the wide geographic spread of common reed described in the present work, the technology of shores stabilization can be applied at almost all lowland water basins of Russia.

  9. The Possible Mechanism and Factors Affecting Synthetic Reactive Dye Removal by Treated Flute Reed

    OpenAIRE

    Chatchawan Singhakant

    2010-01-01

    This study investigated the ability of treated flute-reed to adsorb synthetic reactive dye solution in a batch system. The effects of particle size, contact time and adsorption isotherms at various particle sizes and temperatures were investigated. Desorption was studied to confirm the mechanism of adsorption. The results showed that the adsorption capacity increased as the particle size decreased. The smaller particle size required less contact time to reach equilibrium because it had a high...

  10. Flue gas desulfurization by rotating beds. Final technical report

    Energy Technology Data Exchange (ETDEWEB)

    Gardner, N.; Keyvani, M.; Coskundeniz, A.

    1992-12-01

    The operating and mass transfer characteristics of rotating foam metal beds were studied to determine the potential for flue gas desulfurization. This is a final technical report on the work supported by DOE {number_sign}FG22-87-PC79924. The report is divided into two sections, Part 1 deals primarily with the operating characteristics of rotating beds, and Part 2 covers the mass transfer characteristics of S0{sub 2} absorption in water-lime slurries. Rotating foam metal beds are in essence packed towers operated in high gravitational fields. The foam metal bed is in the form of a cylindrical donut, or torus, and is rotated to produced the high centrifugal forces. The liquid phase enters the bed at the inner surface of the torus and is pulled by the field through the bed. Gas flows countercurrent to the liquid. The bed packing can have a very large specific surface areas and not flood. Possible benefits include much smaller height of a transfer unit resulting in smaller equipment and supporting structures, reduced solvent inventory, faster response with improved process control, reduced pressure drop, and shorter startup and shut-down times. This work is concerned broadly with the operating characteristics of rotating beds, the objectives being to (1) determine the pressure drop through the rotating bed; (2) determine the power required to operate the beds, (3) investigate the residence time distribution of the liquid phase in the beds; and (4) determine the mass transfer coefficients of S0{sub 2} absorption. Three packings of differing specific surface areas were studied, with areas ranging from 656 to 2952 m{sub 2}/m{sub 3}. Liquid flow rates to 36 kg/s*m{sub 2}, gas flow rate to 2.2 kg/s*m{sub 2}, and gravitational fields to 300 g were covered in this study.

  11. Gene flow and genetic structure of the aquatic macrophyte Sparganium emersum in a linear unidirectional river

    NARCIS (Netherlands)

    Pollux, B.J.A.; Luteijn, A.W.W.; Van Groenendael, J.M.; Ouborg, N.J.

    2009-01-01

    1. River systems offer special environments for the dispersal of aquatic plants because of the unidirectional (downstream) flow and linear arrangement of suitable habitats. 2. To examine the effect of this flow on microevolutionary processes in the unbranched bur-reed (Sparganium emersum) we studied

  12. Reed Reactor Facility final report, September 1, 1995--August 31, 1996

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-09-01

    This report covers the period from September 1, 1995 to August 31, 1996. This report is intended to fulfill several purposes including the reporting requirements of the US Nuclear Regulatory Commission, the US Department of Energy, and the Oregon Department of Energy. Highlights of the last year include: student participation in the program is very high; the facility continues its success in obtaining donated equipment from the Portland General Electric, US Department of Energy, and other sources; the facility is developing more paid work; progress is being made in a collaborative project with Pacific Northwest National Laboratory on isotope production for medical purposes. There were over 1,500 individual visits to the Reactor Facility during the year. Most were students in classes at Reed College or area universities, colleges, and high schools. Including tours and research conducted at the facility, the Reed Reactor Facility contributed to the educational programs of six colleges and universities in addition to eighteen pre-college groups. During the year, the reactor was operated almost three hundred separate times. The total energy production was over 23 MW-hours. The reactor staff consists of a Director, an Associated Director, a contract Health Physicist, and approximately twenty Reed College undergraduate students as hourly employees. All radiation exposures to individuals during this year were well below 5% of the federal limits.

  13. Representation of the Solar Capacity Value in the ReEDS Capacity Expansion Model: Preprint

    Energy Technology Data Exchange (ETDEWEB)

    Sigrin, B.; Sullivan, P.; Ibanez, E.; Margolis, R.

    2014-08-01

    An important emerging issue is the estimation of renewables' contributions to reliably meeting system demand, or their capacity value. While the capacity value of thermal generation can be estimated easily, assessment of wind and solar requires a more nuanced approach due to resource variability. Reliability-based methods, particularly, effective load-carrying capacity (ELCC), are considered to be the most robust techniques for addressing this resource variability. The Regional Energy Deployment System (ReEDS) capacity expansion model and other long-term electricity capacity planning models require an approach to estimating CV for generalized PV and system configurations with low computational and data requirements. In this paper we validate treatment of solar photovoltaic (PV) capacity value by ReEDS capacity expansion model by comparing model results to literature for a range of energy penetration levels. Results from the ReEDS model are found to compare well with both comparisons--despite not being resolved at an hourly scale.

  14. Reed Reactor Facility final report, September 1, 1995--August 31, 1996

    International Nuclear Information System (INIS)

    1997-01-01

    This report covers the period from September 1, 1995 to August 31, 1996. This report is intended to fulfill several purposes including the reporting requirements of the US Nuclear Regulatory Commission, the US Department of Energy, and the Oregon Department of Energy. Highlights of the last year include: student participation in the program is very high; the facility continues its success in obtaining donated equipment from the Portland General Electric, US Department of Energy, and other sources; the facility is developing more paid work; progress is being made in a collaborative project with Pacific Northwest National Laboratory on isotope production for medical purposes. There were over 1,500 individual visits to the Reactor Facility during the year. Most were students in classes at Reed College or area universities, colleges, and high schools. Including tours and research conducted at the facility, the Reed Reactor Facility contributed to the educational programs of six colleges and universities in addition to eighteen pre-college groups. During the year, the reactor was operated almost three hundred separate times. The total energy production was over 23 MW-hours. The reactor staff consists of a Director, an Associated Director, a contract Health Physicist, and approximately twenty Reed College undergraduate students as hourly employees. All radiation exposures to individuals during this year were well below 5% of the federal limits

  15. Invertebrate populations in miscanthus (Miscanthusxgiganteus) and reed canary-grass (Phalaris arundinacea) fields

    Energy Technology Data Exchange (ETDEWEB)

    Semere, T.; Slater, F.M. [Llysdinam Field Centre, School of Biosciences, Cardiff University, Newbridge-on-Wye, Llandrindod Wells, Powys, LD1 6NB (United Kingdom)

    2007-01-15

    Monitoring of invertebrates at four field sites in Herefordshire, England, growing miscanthus and reed canary-grass was carried out in 2002, 2003 and 2004 to investigate the ecological impact of these crops on ground beetles, butterflies and arboreal invertebrates. Ground beetles were sampled by pitfall trapping; and arboreal invertebrates by sweep netting and stem beating. The Centre for Ecology and Hydrology's Butterflies Monitoring Scheme methodology was used to record butterflies. The effects of the biomass crops on invertebrates were indirect, through the use of weeds as food resources and habitat. The greater diversity of weed flora within miscanthus fields than within reed canary-grass fields had a greater positive effect on invertebrates. Ground beetles, butterflies and arboreal invertebrates were more abundant and diverse in the most floristically diverse miscanthus fields. The difference in crop architecture and development between miscanthus and reed canary-grass was reflected in their differences in crop height and ground cover early on in the season. However, most of the difference in arthropod abundance between the two crops was attributed to the difference in the agronomic practice of growing the crops such as plant density, and the effect of this on weed growth. Since perennial rhizomatous grasses require a single initial planting and related tillage, and also no major chemical inputs; and because the crops are harvested in the spring and the land is not disturbed by cultivation every year, the fields were used as over-wintering sites for invertebrates suggesting immediate benefits to biodiversity. (author)

  16. [Adsorption Characteristics of Norfloxacin by Biochars Derived from Reed Straw and Municipal Sludge].

    Science.gov (United States)

    Zhang, Han-yu; Wang, Zhao-wei; Gao, Jun-hong; Zhu, Jun-min; Xie, Chao-ran; Xie, Xiao-yun

    2016-02-15

    Two types of biochars were prepared by pyrolyzing reed straw and municipal sludge at the temperature of 500 degrees C. The structure and properties of biochars were characterized by BET, scanning electron microscope (SEM), energy dispersive spectroscopy (EDS) and fourier transform infrared spectroscopy ( FTIR ). The effects of pH value, adsorption time, temperature and initial concentration of norfloxacin (NOR) on the adsorption behaviors were determined by single factor experiments, which were used to preliminarily discuss adsorption mechanism. The results showed that the adsorption of NOR onto biochars derived from reed straw and municipal sludge could reach 70% and 60% of the total adsorption within 12 h, respectively; the maximum adsorption capacities of the two biochars were 2.13 mg x g(-1) (biochar derived from reed straw) and 2.09 mg x g(-1) (biochar derived from municipal sludge). The quantities of both absorptions increased with the decreasing solution pH. The two adsorption kinetics of NOR onto biochars followed the pseudo second order kinetic equations, and adsorption isotherms fitted well with the Langmuir equations. Adsorption thermodynamics parameters such as Gibbs free energy (AG), enthalpy (AH) and entropy (AS) indicated that the two adsorptions were endothermic reactions. Infrared spectroscopy analysis indicated that oxygen-containing functional groups on biochars provided NOR molecules with adsorptive sites, which facilitated the formation of hydrogen bonds between NOR and the biochars.

  17. [Radius reed osteotomy for supination deformity in children with obstetrical brachial plexus palsy].

    Science.gov (United States)

    Alkar, F; Dana, C; Salon, A; Glorion, C

    2013-12-01

    We report our experience and results in the use of reed pronating osteotomy in supination deformities secondary to obstetrical brachial plexus injury. This retrospective study involved 11 patients with paralytic supination of the forearm due to a brachial plexus injury. Other causes of paralytic supination were excluded. The surgical technique consisted of a proximal osteotomy of the ulna fixed by an intramedullary nail and a stable elastic reed osteotomy of the radius. The minimum postoperative follow-up was 2 years. Four boys and seven girls mean aged 8 years (5-12) were operated on between 2000 and 2010. The mean preoperative supination was measured at 63°. The final position average pronation was 37°. Loss of pronation was measured at 15°. No complication was observed. With a mean follow-up of 4 years (2-12), the reed osteotomy of radius associated with a proximal transverse osteotomy of ulna has proven itself effective for correction of paralytic supination of the forearm without complication or reoperation.

  18. An experimental study of the effect of collision properties on spout fluidized bed dynamics

    NARCIS (Netherlands)

    van Buijtenen, M.S.; Börner, Matthias; Deen, N.G.; Heinrich, Stefan; Antonyuk, Sergiy; Kuipers, J.A.M.

    2009-01-01

    In this paper we experimentally study the effect of collision properties of different particle systems on the bed dynamics of a spout fluidized bed. This is done in different flow regimes: the spout-fluidization regime (case A), the jet-in-fluidized-bed regime (case B) and the spouting-with-aeration

  19. Probabilistic estimation of entrainment rate in coarse sediment beds

    Science.gov (United States)

    Bottacin-Busolin, Andrea; Tregnaghi, Matteo; Cecchetto, Martina; Marion, Andrea; Tait, Simon

    2017-04-01

    Many problems in river and coastal engineering depend on sediment transport dynamics induced by turbulent flows over sediment beds. Given the chaotic nature of turbulence and the complex mechanics of granular beds, grain-scale interactions between fluid and sediment are better described using stochastic approaches. A probabilistic model is presented linking entrainment rate to the stochastic properties of the near-bed fluid velocity and the probability distribution of particle elevation. By using a simplified description of the mechanics of grain dislodgement, the distribution of particle waiting time is derived, which is linked to the entrainment rate. The predictive capability of the model and the associated uncertainty are analysed using near-bed flow field and grain motion data obtained from flume experiments at low transport stages. The model predictions are found to be in good agreement with the data. Experimental evidence of distinct entrainment mechanisms is discussed, and flow patterns are identified that cause significant fluctuations in the entrainment rate.

  20. Uso de leitos cultivados de fluxo vertical por batelada no pós-tratamento de efluente de reator anaeróbio compartimentado Post-treatment of effluent of anaerobic baffled reactor using batchwise vertical flow constructed wetland beds

    Directory of Open Access Journals (Sweden)

    Marcelo Mazzola

    2005-06-01

    Full Text Available Neste trabalho avaliou-se o desempenho de um Reator Anaeróbio Compartimentado (RAC de duas câmaras em série, seguido de três leitos cultivados (constructed wetlands de fluxo vertical por batelada. A unidade experimental, em escala piloto, foi instalada na Faculdade de Engenharia Agrícola - UNICAMP, Campinas, SP, Brasil. O volume total do reator era de 2,3 m³ (TDH de 12 h. O efluente do RAC foi tratado em três leitos, dois cultivados com macrófitas (gêneros Typha sp. e Eleocharis sp. e um utilizado como controle (não cultivado. Os leitos, com 2,0 m³ cada um e brita #2 (24 - 35 mm como meio suporte, operaram com fluxo vertical por batelada (com tempos de reação de 24, 48, 72 e 96 h. Na avaliação do RAC, observou-se tendência de estabilização dos parâmetros pH, alcalinidade, ácidos voláteis, sólidos sedimentáveis e suspensos totais, porém a remoção de DQO revelou-se limitada (50%. Nos leitos cultivados o aumento do tempo de reação (até 72 h foi acompanhado pelo aumento de remoção de turbidez, DQO, fósforo e nitrato. O melhor desempenho de remoção de fósforo total foi obtido no leito vegetado com Typha sp para os tempos de 72 e 96 h, respectivamente, de 30 e 25%.This study evaluated the performance of vertical constructed wetlands treating effluent of anaerobic baffled reactor. The anaerobic reactor volume was 2.3 m³; it was operated with daily flow of 4.6 m³ (12 hours Hydraulic Retention Time. The reactor effluent was split into three wetlands beds, two of them cultivated with macrophytes (Typha sp. and Eleocharis sp., and one control. The wetlands were operated as a batch reactor. The medium utilized was gravel, the size ranging from 7 to 12 mm. The reaction time for each cycle (filling - reaction - drainage was 24, 48, 72, and 96 h. The anaerobic reactor achieved the following removal rates: settable solids, 93%; suspended solids, 80%; and COD 39%. The increase in reaction time (up to 72 h for the constructed

  1. A Spouted Bed Reactor Monitoring System for Particulate Nuclear Fuel

    Energy Technology Data Exchange (ETDEWEB)

    D. S. Wendt; R. L. Bewley; W. E. Windes

    2007-06-01

    Conversion and coating of particle nuclear fuel is performed in spouted (fluidized) bed reactors. The reactor must be capable of operating at temperatures up to 2000°C in inert, flammable, and coating gas environments. The spouted bed reactor geometry is defined by a graphite retort with a 2.5 inch inside diameter, conical section with a 60° included angle, and a 4 mm gas inlet orifice diameter through which particles are removed from the reactor at the completion of each run. The particles may range from 200 µm to 2 mm in diameter. Maintaining optimal gas flow rates slightly above the minimum spouting velocity throughout the duration of each run is complicated by the variation of particle size and density as conversion and/or coating reactions proceed in addition to gas composition and temperature variations. In order to achieve uniform particle coating, prevent agglomeration of the particle bed, and monitor the reaction progress, a spouted bed monitoring system was developed. The monitoring system includes a high-sensitivity, low-response time differential pressure transducer paired with a signal processing, data acquisition, and process control unit which allows for real-time monitoring and control of the spouted bed reactor. The pressure transducer is mounted upstream of the spouted bed reactor gas inlet. The gas flow into the reactor induces motion of the particles in the bed and prevents the particles from draining from the reactor due to gravitational forces. Pressure fluctuations in the gas inlet stream are generated as the particles in the bed interact with the entering gas stream. The pressure fluctuations are produced by bulk movement of the bed, generation and movement of gas bubbles through the bed, and the individual motion of particles and particle subsets in the bed. The pressure fluctuations propagate upstream to the pressure transducer where they can be monitored. Pressure fluctuation, mean differential pressure, gas flow rate, reactor

  2. Influence of the convergence angle on the morphodynamics of discordant bed confluences

    OpenAIRE

    Guillén Ludeña, Sebastián; Franca, Rodrigues Pereira Da; Jorge, Mario; Schleiss, Anton; Cardoso, Antonio H.

    2013-01-01

    Within the fluvial network, confluences are particular areas characterized by great ecological value where flow dynamics and bed morphology are much influenced by local patterns. The aim of this article is to describe the influence of the convergence angle on the morphology and hydrodynamics at river channel confluences, where the tributary bed level is higher than the main channel bed (discordant bed). For that purpose, experiments were carried out in a laboratory flume running three dischar...

  3. Bed bug deterrence

    Directory of Open Access Journals (Sweden)

    Haynes Kenneth F

    2010-09-01

    Full Text Available Abstract A recent study in BMC Biology has determined that the immature stage of the bed bug (the nymph signals its reproductive status to adult males using pheromones and thus avoids the trauma associated with copulation in this species. The success of this nymphal strategy of deterrence is instructive. Against the background of increasing problems with bed bugs, this research raises the question whether pheromones might be used to control them. See research article http://www.biomedcentral.com/1741-7007/8/121

  4. Consequences for overcrowding in the emergency room of a change in bed management policy on available in-hospital beds.

    Science.gov (United States)

    Claret, Pierre-Géraud; Boudemaghe, Thierry; Bobbia, Xavier; Stowell, Andrew; Miard, Élodie; Sebbane, Mustapha; Landais, Paul; De La Coussaye, Jean-Emmanuel

    2016-09-01

    Objective Emergency rooms play an important role by providing continuous access to healthcare 24 h a day, 7 days a week, but the lack of available hospital beds has become a major difficulty. Changing bed management policy could improve patient flow. The aim of the present study was to evaluate the consequences of a change in patient prioritisation on available beds. Methods The study consisted of a computerised bed management simulation based on day-by-day data collected from 1 to 31 January 2013 in a teaching hospital. Real hospital data were used to power the computer simulation. The scenarios tested were: (1) priority for emergency and surgery; (2) priority for emergency and medicine; (3) priority for planned admissions and surgery; and (4) priority for planned admissions and medicine. The results of these scenarios were compared with each other and to actual data. Results This study included 2347 patients. The scenario that proved to be the least efficient was the one that gave priority to emergency patients presenting with a medical condition. The scenario that exhibited the best efficiency was the one that gave priority to planned admissions and surgery. Conclusions Changing policies for hospital bed management is worth exploring to improve hospital patient flow and length of stay. What is known about the topic? The lack of available hospital beds is a major difficulty in managing patient flow in emergency rooms (ERs). The ER patient flow competes against a flow of planned hospital admissions for the same beds and the lack of a clearly defined policy on either prioritising ER patient flow over planned admissions or vice versa contributes to a disordered system. What does this paper add? We compared several simulated scenarios corresponding to different bed management policies. The scenario that gave priority to planned admissions and surgery gave the most suitable results. What are the implications for practitioners? Postponing scheduled surgical patients

  5. The Safety of Hospital Beds

    Science.gov (United States)

    Gervais, Pierre; Pooler, Charlotte; Merryweather, Andrew; Doig, Alexa K.; Bloswick, Donald

    2015-01-01

    To explore the safety of the standard and the low hospital bed, we report on a microanalysis of 15 patients’ ability to ingress, move about the bed, and egress. The 15 participants were purposefully selected with various disabilities. Bed conditions were randomized with side rails up or down and one low bed with side rails down. We explored the patients’ use of the side rails, bed height, ability to lift their legs onto the mattress, and ability to turn, egress, and walk back to the chair. The standard bed was too high for some participants, both for ingress and egress. Side rails were used by most participants when entering, turning in bed, and exiting. We recommend that side rails be reconsidered as a means to facilitate in-bed movement, ingress, and egress. Furthermore, single deck height settings for all patients are not optimal. Low beds as a safety measure must be re-evaluated. PMID:28462302

  6. Tidal asymmetry and variability of bed shear stress and sediment bed flux at a site in San Francisco Bay, USA

    Science.gov (United States)

    Brennan, Matthew L.; Schoellhamer, David H.; Burau, Jon R.; Monismith, Stephen G.; Winterwerp, J.C.; Kranenburg, C.

    2002-01-01

    The relationship between sediment bed flux and bed shear stress during a pair of field experiments in a partially stratified estuary is examined in this paper. Time series of flow velocity, vertical density profiles, and suspended sediment concentration were measured continuously throughout the water column and intensely within 1 meter of the bed. These time series were analyzed to determine bed shear stress, vertical turbulent sediment flux, and mass of sediment suspended in the water column. Resuspension, as inferred from near-bed measurements of vertical turbulent sediment flux, was flood dominant, in accordance with the flood-dominant bed shear stress. Bathymetry-induced residual flow, gravitational circulation, and ebb tide salinity stratification contributed to the flood dominance. In addition to this flow-induced asymmetry, the erodibility of the sediment appears to increase during the first 2 hours of flood tide. Tidal asymmetry in bed shear stress and erodibility help explain an estuarine turbidity maximum that is present during flood tide but absent during ebb tide. Because horizontal advection was insignificant during most of the observation periods, the change in bed mass can be estimated from changes in the total suspended sediment mass. The square wave shape of the bed mass time series indicates that suspended sediment rapidly deposited in an unconsolidated or concentrated benthic suspension layer at slack tides and instantly resuspended when the shear stress became sufficiently large during a subsequent tide. The variability of bed mass associated with the spring/neap cycle (about 60 mg/cm2) is similar to that associated with the semidiurnal tidal cycle.

  7. Bed Prism Spectacles

    Science.gov (United States)

    Ribeiro, Jair Lúcio Prados

    2018-01-01

    We only became aware of the existence of bed prism spectacles when a student brought them to the classroom and asked us about how they work. The device proved to be a fertile source of curiosity among the students, and, to be properly understood, it required us to develop a comparison between reflection in a typical mirror and total internal…

  8. Practice Hospital Bed Safety

    Science.gov (United States)

    ... the mattress end Subscribe: FDA Consumer Health Information "Hospital beds are found in nearly all patient care settings or environments," says Joan Ferlo Todd, RN, a senior nurse-consultant at the Food and Drug Administration’s (FDA) Center for Devices and Radiological Health (CDRH). " ...

  9. Development of a generic engineering model for packed bed reactors using computational fluid dynamics

    NARCIS (Netherlands)

    Tuinstra, B.F.

    2008-01-01

    Packed bed reactors are used in many chemical processes. With the advent of modern computers, flow simulation (Computational Fluid Dynamics, CFD) can be an aid in the design of process equipment. For particulate systems like packed bed reactors, simulation of the flow around the particles is very

  10. Gas-particle interactions in dense gas-fluidised beds

    NARCIS (Netherlands)

    Li, J.; Kuipers, J.A.M.

    2003-01-01

    The occurrence of heterogeneous flow structures in gas-particle flows seriously affects gas¿solid contacting and transport processes in dense gas-fluidized beds. A computational study, using a discrete particle method based on Molecular Dynamics techniques, has been carried out to explore the

  11. Application of semifluidized bed bioreactor as novel bioreactor ...

    African Journals Online (AJOL)

    The conventional bioreactors such as pond digester, anaerobic filtration, up-flow anaerobic sludge blanket (UASB), up-flow anaerobic sludge fixed-film (UASFF), continuous stirred tank reactor (CSTR), anaerobic contact digestion and fluidized bed, used over the past decades are largely operated anaerobically. They have ...

  12. Fluidized bed incineration of a slurry waste from caprolactam production

    Energy Technology Data Exchange (ETDEWEB)

    Cammarota, A.; D' Amore, M.; Donsi, G.; Massimilla, L.

    1980-08-01

    Caprolactam tails are a slurry waste produced in the SNIA process for the synthesis of caprolactam. They contain about 65% water, 25% ash and 10% combustible matter. The ashes are low melting, due to the presence of sodium compounds. The incineration of this waste is carried out at temperatures below 600/sup 0/C in beds of silica sand, using a laboratory scale apparatus with a 40 mm ID fluidization column. Variables investigated include sand particle size, slurry flow rate, bed temperature, bed height. The concentrations of CO/sub 2/ and CO are determined continuously in the flue gases. Bed solids are sampled periodically to determine the carbon content. Results of experiments show that the low temperature incineration on a bed of inert solids is a useful technique for the disposal of caprolactam tails. 8 refs.

  13. Representation of Solar Capacity Value in the ReEDS Capacity Expansion Model

    Energy Technology Data Exchange (ETDEWEB)

    Sigrin, B. [National Renewable Energy Lab. (NREL), Golden, CO (United States); Sullivan, P. [National Renewable Energy Lab. (NREL), Golden, CO (United States); Ibanez, E. [National Renewable Energy Lab. (NREL), Golden, CO (United States); Margolis, R. [National Renewable Energy Lab. (NREL), Golden, CO (United States)

    2014-03-01

    An important issue for electricity system operators is the estimation of renewables' capacity contributions to reliably meeting system demand, or their capacity value. While the capacity value of thermal generation can be estimated easily, assessment of wind and solar requires a more nuanced approach due to the resource variability. Reliability-based methods, particularly assessment of the Effective Load-Carrying Capacity, are considered to be the most robust and widely-accepted techniques for addressing this resource variability. This report compares estimates of solar PV capacity value by the Regional Energy Deployment System (ReEDS) capacity expansion model against two sources. The first comparison is against values published by utilities or other entities for known electrical systems at existing solar penetration levels. The second comparison is against a time-series ELCC simulation tool for high renewable penetration scenarios in the Western Interconnection. Results from the ReEDS model are found to compare well with both comparisons, despite being resolved at a super-hourly temporal resolution. Two results are relevant for other capacity-based models that use a super-hourly resolution to model solar capacity value. First, solar capacity value should not be parameterized as a static value, but must decay with increasing penetration. This is because -- for an afternoon-peaking system -- as solar penetration increases, the system's peak net load shifts to later in the day -- when solar output is lower. Second, long-term planning models should determine system adequacy requirements in each time period in order to approximate LOLP calculations. Within the ReEDS model we resolve these issues by using a capacity value estimate that varies by time-slice. Within each time period the net load and shadow price on ReEDS's planning reserve constraint signals the relative importance of additional firm capacity.

  14. Thermal enhancement cartridge heater modified (TECH Mod) tritium hydride bed development, Part 1 - Design and fabrication

    Energy Technology Data Exchange (ETDEWEB)

    Klein, J.E.; Estochen, E.G. [Savannah River National Laboratory, Aiken, SC (United States)

    2015-03-15

    The Savannah River Site (SRS) tritium facilities have used first generation (Gen1) LaNi{sub 4.25}Al{sub 0.75} (LANA0.75) metal hydride storage beds for tritium absorption, storage, and desorption. The Gen1 design utilizes hot and cold nitrogen supplies to thermally cycle these beds. Second and third generation (Gen2 and Gen3) storage bed designs include heat conducting foam and divider plates to spatially fix the hydride within the bed. For thermal cycling, the Gen2 and Gen3 beds utilize internal electric heaters and glovebox atmosphere flow over the bed inside the bed external jacket for cooling. The currently installed Gen1 beds require replacement due to tritium aging effects on the LANA0.75 material, and cannot be replaced with Gen2 or Gen3 beds due to different designs of these beds. At the end of service life, Gen1 bed desorption efficiencies are limited by the upper temperature of hot nitrogen supply. To increase end-of-life desorption efficiency, the Gen1 bed design was modified, and a Thermal Enhancement Cartridge Heater Modified (TECH Mod) bed was developed. Internal electric cartridge heaters in the new design to improve end-of-life desorption, and also permit in-bed tritium accountability (IBA) calibration measurements to be made without the use of process tritium. Additional enhancements implemented into the TECH Mod design are also discussed. (authors)

  15. THERMAL ENHANCEMENT CARTRIDGE HEATER MODIFIED TECH MOD TRITIUM HYDRIDE BED DEVELOPMENT PART I DESIGN AND FABRICATION

    Energy Technology Data Exchange (ETDEWEB)

    Klein, J.; Estochen, E.

    2014-03-06

    The Savannah River Site (SRS) tritium facilities have used 1{sup st} generation (Gen1) LaNi{sub 4.25}Al{sub 0.75} (LANA0.75) metal hydride storage beds for tritium absorption, storage, and desorption. The Gen1 design utilizes hot and cold nitrogen supplies to thermally cycle these beds. Second and 3{sup rd} generation (Gen2 and Gen3) storage bed designs include heat conducting foam and divider plates to spatially fix the hydride within the bed. For thermal cycling, the Gen2 and Gen 3 beds utilize internal electric heaters and glovebox atmosphere flow over the bed inside the bed external jacket for cooling. The currently installed Gen1 beds require replacement due to tritium aging effects on the LANA0.75 material, and cannot be replaced with Gen2 or Gen3 beds due to different designs of these beds. At the end of service life, Gen1 bed desorption efficiencies are limited by the upper temperature of hot nitrogen supply. To increase end-of-life desorption efficiency, the Gen1 bed design was modified, and a Thermal Enhancement Cartridge Heater Modified (TECH Mod) bed was developed. Internal electric cartridge heaters in the new design to improve end-of-life desorption, and also permit in-bed tritium accountability (IBA) calibration measurements to be made without the use of process tritium. Additional enhancements implemented into the TECH Mod design are also discussed.

  16. VA National Bed Control System

    Data.gov (United States)

    Department of Veterans Affairs — The VA National Bed Control System records the levels of operating, unavailable and authorized beds at each VAMC, and it tracks requests for changes in these levels....

  17. Bed failure induced by internal solitary waves

    Science.gov (United States)

    Rivera-Rosario, Gustavo A.; Diamessis, Peter J.; Jenkins, James T.

    2017-07-01

    The pressure field inside a porous bed induced by the passage of an Internal Solitary Wave (ISW) of depression is examined using high-accuracy numerical simulations. The velocity and density fields are obtained by solving the Dubreil-Jacotin-Long Equation, for a two-layer, continuously stratified water column. The total wave-induced pressure across the surface of the bed is computed by vertically integrating for the hydrostatic and nonhydrostatic contributions. The bed is assumed to be a continuum composed of either sand or silt, with a small amount of trapped gas. Results show variations in pore-water pressure penetrating deeper into more conductive materials and remaining for a prolonged period after the wave has passed. In order to quantify the potential for failure, the vertical pressure gradient is compared against the buoyant weight of the bed. The pressure gradient exceeds this weight for weakly conductive materials. Failure is further enhanced by a decrease in bed saturation, consistent with studies in surface-wave induced failure. In deeper water, the ISW-induced pressure is stronger, causing failure only for weakly conductive materials. The pressure associated with the free-surface displacement that accompanies ISWs is significant, when the water depth is less than 100 m, but has little influence when it is greater than 100 m, where the hydrostatic pressure due to the pycnocline displacement is much larger. Since the pore-pressure gradient reduces the specific weight of the bed, results show that particles are easier for the flow to suspend, suggesting that pressure contributes to the powerful resuspension events observed in the field.

  18. Early successional stages of reed Phragmites australis vegetations and its importance for the Bearded Reedling Panurus biarmicus in Oostvaardersplassen, The Netherlands

    NARCIS (Netherlands)

    Beemster, Nico; Troost, Els; Platteeuw, Maarten

    2010-01-01

    A study on Bearded Reed ling Panurus biarmicus feeding habits in combination with a sample-wise breeding bird survey of the marshland zones of the Dutch wetland Oostvaardersplassen shows clear-cut spatial differences in densities and habitat use. The more mature stands of Reed Phragmites australis

  19. Systematic Procedure for Integrated Process Operation: Reverse Electro-Enhanced Dialysis (REED) during Lactic Acid Fermentation

    DEFF Research Database (Denmark)

    Prado Rubio, Oscar Andres; Jørgensen, Sten Bay; Jonsson, Gunnar Eigil

    2011-01-01

    The integration of lactic acid fermentation and Reverse Electro-Enhanced Dialysis (REED) is investigated based upon previously developed mathematical models. A goal driven process and operation design procedure is proposed and partially investigated. The conceptual analysis of the processes...... integration shows the need for an additional pH controller in the fermenten A PI controller is implemented and tested. The complete control structure for the integrated system consists of this PI controller in the fermenter plus a previously developed (Prado-Rubio et al., 2010) input resetting control...

  20. Simulating transmission and control of Taenia solium infections using a reed-frost stochastic model

    DEFF Research Database (Denmark)

    Kyvsgaard, Niels Chr.; Johansen, Maria Vang; Carabin, Hélène

    2007-01-01

    The transmission dynamics of the human-pig zoonotic cestode Taenia solium are explored with both deterministic and stochastic versions of a modified Reed-Frost model. This model, originally developed for microparasitic infections (i.e. bacteria, viruses and protozoa), assumes that random contacts...... humans eating under-cooked pork meat harbouring T. solium metacestodes. Deterministic models of each scenario were first run, followed by stochastic versions of the models to assess the likelihood of infection elimination in the small population modelled. The effects of three groups of interventions were...

  1. Numerical modeling of pyrolysis of sawdust in a packed bed

    Energy Technology Data Exchange (ETDEWEB)

    Meng, Qingmin; Chen, Xiaoping [Southeast Univ., Nanjing (China). School of Energy and Environment

    2013-07-01

    An unsteady, one-dimensional mathematical model has been developed to describe the pyrolysis of sawdust in a packed bed. The sawdust bed was pyrolyzed using the hot gas and an electric heater outside the bed as the source of energy. The developed model includes mass, momentum and energy conservations of gas and solid within the bed. The gas flow in the bed is modeled using Darcy's law for fluid through a porous medium. The heat transfer model includes heat conduction inside the bed and convection between the bed and the hot gas. The kinetic model consists of primary pyrolysis reaction. A finite volume fully implicit scheme is employed for solving the heat and mass transfer model equations. A Runge-Kutta fourth order method is used for the chemical kinetics model equations. The model predictions of mass loss history and temperature were validated with published experimental results, showing a good agreement. The effects of inlet temperature on the pyrolysis process have been analyzed with model simulation. A sensitivity analysis using the model suggests that the predictions could be improved by considering the second reaction which could generate volatile flowing in the void.

  2. Continuous fermentation and in-situ reed separation of butyric acid for higher sugar consumption rate and productivity

    DEFF Research Database (Denmark)

    Baroi, George Nabin; Skiadas, Ioannis; Westermann, Peter

    that disconnection of the REED system resulted to much lower (48 and 83% for glucose and xylose, respectively) sugars consumption rates and consequently lower butyric acid production rates. It was also noticeable that continuous operation, even without the REED system, resulted to higher glucose consumption rates...... than batch operation (0.85 compared to 0.31 g/L/h). Similar conclusions were drawn from the experiments with increasing concentrations of PHWS. It should also be emphasized that fermentation of 100% PHWS proceeded unhindered with just urea and K2HPO4 added (to making up for nutrient deficiency...

  3. Nail bed onychomatricoma.

    Science.gov (United States)

    Wang, Lei; Gao, Tianwen; Wang, Gang

    2014-10-01

    Onychomatricoma is a rare tumor originating from the nail matrix, and, in rare conditions, from the ventral aspect of the proximal nailfold. Here we report a rare case of a 51-year-old man presenting with melanonychia mainly involving the distal nail plate. Histopathologic examination showed typical findings of onychomatricoma mainly involving the nail bed, while the nail matrix was largely uninvolved. We also identified fungal infection in a focal area of the distal nail plate. Our findings indicate that onychomatricoma can develop in the surrounding epithelial tissue of the nail unit, including the nail bed, and suggest that fungal infection may represent a secondary phenomenon of onychomatricoma. © 2014 John Wiley & Sons A/S. Published by John Wiley & Sons Ltd.

  4. Geomechanics of bedded salt

    International Nuclear Information System (INIS)

    Serata, S.; Milnor, S.W.

    1979-01-01

    Creep data from the literature search is reinterpreted by SGI, resulting in a better understanding of the temperature and stress state dependence of the octahedral creep rate and the octahedral shear strength. The concept of a transition strength between the elastic and the plastic states is in agreement with the data. The elastic and rheological properties of salt are described, and a set of constitutive equations is presented. The dependence of material properties on parameters such as temperature is considered. Findings on the permeability of salt are summarized, and the in-situ behavior of openings in bedded salt is described based on extensive engineering experience. A stress measuring system utilizing a finite element computer code is discussed. Geological factors affecting the stability of salt openings are considered, and the Stress Control Technique for designing stable openings in bedded salt formations is explained

  5. [Nest habitat quality evaluation for the oriental great reed warbler (Acrocephalus orientalis) in Baiyangdian Wetland].

    Science.gov (United States)

    Zhao, Zhi-Xuan; Yan, Deng-Hua; Geng, Lei-Hua; Lin, Jin; Feng, Hua-Li

    2014-05-01

    The Baiyangdian Wetland Natural Reserve is an important breeding habitat for oriental great reed warbler (OGRWs), Acrocephalus orientalis, in North China Plain. We investigated the nesting sites of OGRWs by line transect method during June-July, 2011, and 112 nests were found out in total. The ecological-niche factor analysis (ENFA) was applied in nesting habitat suitability assessment for OGRWs in Baiyangdian. The results showed that OGRWs in this reserve preferred nesting in dry land reed landscapes, which located at relatively high altitudes and away from anthropocentric disturbance. In 2011, the suitable and the most suitable nesting habitats of OGRWs in this reserve were 2474.69 hm2 and 1131.19 hm2, accounting 7.6% and 3.5% of the total reserve area, respectively. The most suitable nesting habitats shaped a circle-like structure, and they all clustered together around Damai and Shaoche core area, which located in the east part of the reserve. In order to protect the nesting habitats for OGRWs within Baiyangdian wetland reserve, it was suggested that the functional zone should be reorganized, and that the Damai and Shaoche core area should be integrated into one. This new core area would be bigger and more concentrated, at the same time the buffer zone should also be established appropriately, so as to protect the natural landscapes in this reserve as much as possible.

  6. Reed Reactor Facility final report, September 1, 1994--August 31, 1995

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-09-01

    This report covers the period from September 1, 1994 to August 31, 1995. Information contained in this report is intended to fulfill several purposes including the reporting requirements of the US Nuclear Regulatory Commission (USNRC), the US Department of Energy (USDOE), and the Oregon Department of Energy (ODOE). Highlights of the last year include: student participation in the program is very high; the facility has been extraordinarily successful in obtaining donated equipment from Portland General Electric, US Department of Energy, Precision Castparts, Tektronix, and other sources; the facility is developing more paid work. There were 1,115 visits of the Reactor Facility by individuals during the year. Most of these visitors were students in classes at Reed College or area universities, colleges, and high schools. During the year, the reactor was operated 225 separate times on 116 days. The total energy production was 24.6 MW-hours. The reactor staff consists of a Director, an Associate Director, a contract Health Physicist, and approximately fifteen Reed College undergraduate students as hourly employees. All radiation exposures to individuals during this year were well below 1% of the federal limits. There were no releases of liquid radioactive material from the facility and airborne releases (primarily {sup 41}Ar) were well within regulatory limits.

  7. Reed Reactor Facility final report, September 1, 1994--August 31, 1995

    International Nuclear Information System (INIS)

    1997-01-01

    This report covers the period from September 1, 1994 to August 31, 1995. Information contained in this report is intended to fulfill several purposes including the reporting requirements of the US Nuclear Regulatory Commission (USNRC), the US Department of Energy (USDOE), and the Oregon Department of Energy (ODOE). Highlights of the last year include: student participation in the program is very high; the facility has been extraordinarily successful in obtaining donated equipment from Portland General Electric, US Department of Energy, Precision Castparts, Tektronix, and other sources; the facility is developing more paid work. There were 1,115 visits of the Reactor Facility by individuals during the year. Most of these visitors were students in classes at Reed College or area universities, colleges, and high schools. During the year, the reactor was operated 225 separate times on 116 days. The total energy production was 24.6 MW-hours. The reactor staff consists of a Director, an Associate Director, a contract Health Physicist, and approximately fifteen Reed College undergraduate students as hourly employees. All radiation exposures to individuals during this year were well below 1% of the federal limits. There were no releases of liquid radioactive material from the facility and airborne releases (primarily 41 Ar) were well within regulatory limits

  8. Dynamic transition between fixed- and mobile-bed: mathematical and numerical aspects

    Science.gov (United States)

    Zugliani, Daniel; Pasqualini, Matteo; Rosatti, Giorgio

    2017-04-01

    Free-surface flows with high sediment transport (as debris flow or hyper-concentrated flow) are composed by a mixture of fluid and solid phase, usually water and sediment. When these flows propagate over loose beds, particles constituting the mixture of water and sediments strongly interact with the ones forming the bed, leading to erosion or deposition. However, there are lots of other situations when the mixture flows over rigid bedrocks or over artificially paved transects, so there is no mass exchange between bed and mixture. The two situations are usually referred to as, respectively, mobile- and fixed-bed conditions. From a mathematical point of view, the systems of Partial Differential Equations (PDEs) that describe these flows derive from mass and momentum balance of both phases, but, the two resulting PDEs systems are different. The main difference concerns the concentration: in the mobile-bed condition, the concentration is linked to the local flow conditions by means of a suitable rheological relation, while in the fixed-bed case, the concentration is an unknown of the problem. It is quite common that a free surface flow with high sediment transport, in its path, encounters both conditions. In the recent work of Rosatti & Zugliani 2015, the mathematical and numerical description of the transition between fixed- and mobile-bed was successfully resolved, for the case of low sediment transport phenomena, by the introduction of a suitable erodibility variable and satisfactory results were obtained. The main disadvantage of the approach is related to the erodibility variable, that changes in space, based on bed characteristics, but remains constant in time. However, the nature of the bed can change dynamically as result of deposition over fixed bed or high erosion over mobile bed. With this work, we extend the applicability of the mentioned approach to the more complex PDEs describing the hyper-concentrated flow. Moreover, we introduce a strategy that allows

  9. Predicting Bed Mobility in a Simple River Channel

    Science.gov (United States)

    Wydzga, M. A.; Legleiter, C.; Dunne, T.

    2007-12-01

    Prediction of the frequency and spatial pattern of bed mobility in gravel bed rivers is central to a wide range of theoretical and applied interests ranging from sediment transport to the impacts of natural or managed floods on aquatic organisms. Although bed mobility has been investigated in numerous flume and field studies, accurate predictions of grain entrainment and transport in gravel bed rivers remain elusive. Alluvial rivers typically encompass a much wider range of hydraulic and sedimentological conditions than those that have been recreated in laboratory flume studies upon which many grain entrainment and transport models are based. These flume studies are limited to the examination of processes occurring over the short term, commonly with the absence of slower processes such as fine-grain infilling. On the other hand, in field studies key variables can not be controlled and the spatial complexity of processes and conditions complicate data collection and analysis. A unique opportunity currently exists to help bridge this gap between laboratory and field studies: a 3.2 km long, recently constructed, single thread, alternate bar, gravel bed river channel of the Merced River. This channel, constructed for ecosystem restoration purposes, is slowly developing greater complexity, but is still currently defined by a simple plan form and cross-sectional channel geometry compared to most natural gravel bed river channels. This channel can thus be considered a full-scale flume. In the six years since the channel was constructed, a wider range of sedimentological bed conditions have evolved than have been created in a laboratory flume. We are characterizing the bed grain sizes, flow field, grain entrainment, and the sedimentological or bed state conditions in this simple channel. The flow field is modeled using a calibrated, 2D hydrodynamic flow model, MD_SWMS. Grain entrainment is measured with both metal tags inserted into the bed, and painted rock tracers

  10. Direct contact condensation in packed beds

    Energy Technology Data Exchange (ETDEWEB)

    Li, Yi; Klausner, James F.; Mei, Renwei; Knight, Jessica [Department of Mechanical and Aerospace Engineering, University of Florida, Gainesville, FL 32611 (United States)

    2006-12-15

    A diffusion driven desalination process was recently described where a very effective direct contact condenser with a packed bed is used to condense water vapor out of an air/vapor mixture. A laboratory scale direct contact condenser has been fabricated as a twin tower structure with two stages, co-current and countercurrent. Experiments have been operated in each stage with respective saturated air inlet temperatures of 36, 40 and 43{sup o}C. The temperature and humidity data have been collected at the inlet and exit of the packed bed for different water to air mass flow ratios that vary between 0 and 2.5. A one-dimensional model based on conservation principles has been developed, which predicts the variation of temperature, humidity, and condensation rate through the condenser stages. Agreement between the model and experiments is very good. It is observed that the countercurrent flow stage condensation effectiveness is significantly higher than that for the co-current stage. The condensation heat and mass transfer rates were found to decrease when water blockages occur within the packed bed. Using high-speed digital cinematography, it was observed that this problem can occur at any operating condition, and is dependent on the packing surface wetting characteristics. This observation is used to explain the requirement for two different empirical constants, depending on packing diameter, suggested by Onda for the air side mass transfer coefficient correlation. (author)

  11. INVESTIGATION OF PROCESSES OF WATER CONSUMPTION BY NATURAL REEDS AND DEVELOPMENT ON ITS BASIS OF THE MATHEMATICAL MODEL OF THE PROCESS

    Directory of Open Access Journals (Sweden)

    Mukanov Ruslan Vladimirovich

    2018-01-01

    Full Text Available Subject: the article considers the possibility of using wild-growing reeds as an effective heat-insulating material in the construction of buildings for various purposes. The main advantages and disadvantages of reeds are analyzed, and it is shown that according to the thermo-technical characteristics cane can be used effectively as a heat-insulating material. Since the thermal conductivity (thermal resistance of hygroscopic heat-insulating materials depends on their moisture content, a series of experiments was conducted to assess the moisture saturation of natural reeds under conditions of high air humidity. The obtained results were processed to obtain mathematical models for consumption of moisture by reeds during the material exploitation. Research objectives: creation of a mathematical model for calculating the moisture consumption parameters of reed stalks at high humidity parameters of the ambient air. Materials and methods: to achieve the goal, an experimental plant was developed for moistening the reed stalks, in which the samples were kept for several days. Three types of reed stalks were selected: stems with a length of 70 mm and an average diameter of 10 mm: 1 - without leaves; 2 - with leaves along the entire length of the cane; 3 - with leaves and nodal septa. Laboratory samples were brought to the state of their natural weight in the author-developed chamber with infrared heaters in the medium of calcined calcium chloride to absorb the moisture. After conducting the experiments, the moistened reed was weighed to determine the moisture saturation. Results: it has been experimentally confirmed that the curves of moisture saturation of reeds have a nonlinear character. The rate of water absorption in the first two days was 7.9 % for the first type, 8.7 % for the second type and 9.8 % for the third type of reeds. After the first two days the rate of water absorption decreased and after eight days (168 hours was 15.6 % for samples of

  12. Decreased distensibility of a passive vascular bed in diabetes mellitus

    DEFF Research Database (Denmark)

    Faris, I; Agerskov, K; Henrikson, O

    1982-01-01

    This study was undertaken to determine whether the distensibility of a passive vascular bed is reduced in Type 1 (insulin-dependent) diabetic patients with microangiopathy. The change in blood flow induced by 45 degrees head-up tilting was studied in two systems: (a) following maximal ischaemic...... exercise and (b) in a vascular bed locally paralysed by the injection of papaverine. Five normal subjects, six patients with long-standing Type 1 diabetes and six non-diabetic patients with severe atherosclerosis affecting the legs were studied. Blood flow was measured in the anterior tibial muscle...... by the isotope washout technique. The median increase in blood flow produced by tilting was greater in normal subjects than in diabetic subjects in both the locally-relaxed bed (58% and 14% respectively) and after maximal ischaemic exercise (45% and 4% respectively). In the atherosclerotic subjects, the increase...

  13. Application of willow and reed vegetation filters for protection of a stream passing through a zoo

    Energy Technology Data Exchange (ETDEWEB)

    Obarska-Pempkowiak, H. [Technical Univ. of Gdansk (Poland). Faculty of Hydrotechnics

    1994-12-31

    The Rynaszewski Stream (water flow 25 l/s) is the main tributary of the Jelitkowski Stream which in turn drains to the Bay of Gdansk (Baltic Sea) in an area of popular beaches and hotels. In its middle part, the Rynaszewski Stream passes through the Zoological Gardens in Oliwa, where it is used to receive loads of organic matter and nutrients originating from deer-runs (surface sources) and ponds inhabited with waterfowl, hippopotamus, seals and penguins. Major contaminants identified in water are organic nitrogen and bacteria. In order to protect the Rynaszewski Stream, several hydrobotanical constructions were created in 1992. They included areas of land along the stream planted with willow - Salix viminalis (buffer zones), localized in order to purify surface flow waters. Root zone beds (Phragmites communis), soil filters and artificial wetlands were constructed to purify water from point sources. The effects of the measures taken to protect the Rynaszewski Stream from contaminations were assessed based on results of measurements carried out in samples collected once a month during May to December, 1993. The analyses of organic matter (COD and BOD{sub 5}), nutrients (various species of phosphorus and nitrogen) and coli index were performed. A substantial improvement of water was found in 1993 as compared with 1991. This manifested itself in the decrease of total nitrogen (from 8.8 mg/l in 1991 to 1.75 mg/l in 1993), phosphate (respectively 0.2 mg/l and 0.1 mg/l) and coli index (respectively 0.04 and 0.16). The results indicate that hydrobotanical purification systems are capable of protecting streams from contamination coming from both surface and point sources. 3 refs, 6 figs, 3 tabs

  14. Isolating roughness scales of gravel-bed patches

    Science.gov (United States)

    Bertin, Stephane; Groom, Jane; Friedrich, Heide

    2017-08-01

    There is a growing consensus that gravel-bed roughness should be parameterized based on bed-surface topography, not only sediment size. One benefit is the possible identification of various spatial scales of surface roughness and evaluation of their respective contributions to flow resistance (and also to bedload transport). The absence of relationships between roughness at the different scales is apparent in previous work, which currently limits roughness parameterization from topography and application in flow modeling. This study examines the use of moving-window detrending on gravel-bed digital elevation models (DEMs) for isolating roughness scales and their respective signatures. A large data set of 35 water-worked gravel-bed patches from both the laboratory and the field was used for the analysis. The measured bed topography was separated into two distinct DEMs: one representing grains, the other representing small bedforms. For all DEMs, bed-elevation parameters measuring vertical roughness, imbrication, and spatial correlations were determined. Our results show distinct topographic signatures between grain and bedform DEMs. We show strong positive linear relationships between grain vertical roughness and the size of the bed-surface material. Surface sediment arrangement also determined bedform shape, with groupings of coarse sediment forming humps on the surface, and finer sediment sheltered in hollows. Patch-scale vertical roughness could not be estimated simply as the sum of grain and bedform vertical roughness. Instead, our results suggest weighted summation and the existence of universal weighting coefficients. Practical applications for studies on gravel-bed roughness and flow modeling using DEMs are discussed.

  15. Materials support for EPRI Fluidized-Bed Combustion Program

    International Nuclear Information System (INIS)

    Sethi, V.K.; Wright, I.G.

    1993-05-01

    This research project was intended to provide technical support for materials aspects of EPRI's U.C. Fluidized Bed Combustor Program. The scope of this support included participation in the EPRI FBC materials oversight panel, inspection of fluidized beds during forced or planned outages, analysis of materials failures and of associated deposits, participation in technical meetings involving fluidized bed materials. Volume I describes the results of exposing for approximately 5,000 hours in the Georgetown AFBC a number of surface modifications that had been reported to have promise in combating in-bed evaporator tube wastage. Some measures were applied to sample lengths of carbon-steel tubing, and installed as part of the in-bed evaporator tube bundle at Georgetown. These tubes are inspected periodically while still installed in the unit, and were finally cut out and subjected to detailed measurements and metallographic evaluation. The exposure at regular intervals throughout the bed of plain carbon-steel tubes that were honed and surface-ground allowed a baseline measurement of the wastage potential of this bed, which was high. Qualitatively, all but one of the protective measures tested reduced wastage. The unprotected tubes showed that wastage occurred mainly on the underside of the tubes, with maximum wear at the tube bottom. The protective measures that were exposed were densely studded tubes, fins and flow separators, fins and studs on the underside of the tube, and longitudinal rods. These surface modifications were exposed in the chromized and unchromized conditions, together with plain carbon-steel tubes that had been chromized. The tubes with fins and flow separators exhibited continued wastage on the underside between the flow separators, which was attributed in part to the steep inclination of the tubes in the bed. The plain, chromized tubes, together with the armored, chromized tubes, exhibited virtually no wastage of the tube surface nor of the armor

  16. Understanding and predicting bed humidity in fluidized bed granulation.

    Science.gov (United States)

    Hu, Xinhui; Cunningham, John; Winstead, Denita

    2008-04-01

    Bed humidity is a critical parameter that needs to be controlled in a fluidized bed granulation to ensure reliability. To predict and control the bed humidity during the fluidized bed granulation process, a simple model based on the mass conservation of moisture was developed. The moisture mass balance model quantitatively simulates the effects of spray rate, binder solution concentration, airflow rate, inlet air temperature, and dew point on the bed humidity. The model was validated by a series of granulations performed in different scale granulators including Glatt GPCG-1, GPCG-15, and GPCG-60. Good agreement was observed between the theoretical prediction and the measured loss on drying (LOD). The model developed in the current work enables us to choose the appropriate parameters for the fluidized bed granulation and can be used as a valuable tool in process scaling-up. 2007 Wiley-Liss, Inc

  17. Coal Bed Methane Primer

    Energy Technology Data Exchange (ETDEWEB)

    Dan Arthur; Bruce Langhus; Jon Seekins

    2005-05-25

    During the second half of the 1990's Coal Bed Methane (CBM) production increased dramatically nationwide to represent a significant new source of income and natural gas for many independent and established producers. Matching these soaring production rates during this period was a heightened public awareness of environmental concerns. These concerns left unexplained and under-addressed have created a significant growth in public involvement generating literally thousands of unfocused project comments for various regional NEPA efforts resulting in the delayed development of public and fee lands. The accelerating interest in CBM development coupled to the growth in public involvement has prompted the conceptualization of this project for the development of a CBM Primer. The Primer is designed to serve as a summary document, which introduces and encapsulates information pertinent to the development of Coal Bed Methane (CBM), including focused discussions of coal deposits, methane as a natural formed gas, split mineral estates, development techniques, operational issues, producing methods, applicable regulatory frameworks, land and resource management, mitigation measures, preparation of project plans, data availability, Indian Trust issues and relevant environmental technologies. An important aspect of gaining access to federal, state, tribal, or fee lands involves education of a broad array of stakeholders, including land and mineral owners, regulators, conservationists, tribal governments, special interest groups, and numerous others that could be impacted by the development of coal bed methane. Perhaps the most crucial aspect of successfully developing CBM resources is stakeholder education. Currently, an inconsistent picture of CBM exists. There is a significant lack of understanding on the parts of nearly all stakeholders, including industry, government, special interest groups, and land owners. It is envisioned the Primer would being used by a variety of

  18. Bed Rest Muscular Atrophy

    Science.gov (United States)

    Greenleaf, John E.

    2000-01-01

    A major debilitating response from prolonged bed rest (BR) is muscle atrophy, defined as a "decrease in size of a part of tissue after full development has been attained: a wasting away of tissue as from disuse, old age, injury or disease". Part of the complicated mechanism for the dizziness, increased body instability, and exaggerated gait in patients who arise immediately after BR may be a result of not only foot pain, but also of muscular atrophy and associated reduction in lower limb strength. Also, there seems to be a close association between muscle atrophy and bone atrophy. A discussion of many facets of the total BR homeostatic syndrome has been published. The old adage that use determines form which promotes function of bone (Wolff's law) also applies to those people exposed to prolonged BR (without exercise training) in whom muscle atrophy is a consistent finding. An extreme case involved a 16-year-old boy who was ordered to bed by his mother in 1932: after 50 years in bed he had "a lily-white frame with limbs as thin as the legs of a ladder-back chair". These findings emphasize the close relationship between muscle atrophy and bone atrophy. In addition to loss of muscle mass during deconditioning, there is a significant loss of muscle strength and a decrease in protein synthesis. Because the decreases in force (strength) are proportionately greater than those in fiber size or muscle cross-sectional area, other contributory factors must be involved; muscle fiber dehydration may be important.

  19. Does conspicuous colouration of Magpies Pica pica influence aggressive behaviour in nesting Great Reed Warblers Acrocephalus arundinaceus?

    Czech Academy of Sciences Publication Activity Database

    Trnka, A.; Požgayová, Milica

    2017-01-01

    Roč. 64, č. 1 (2017), s. 108-111 ISSN 0006-3657 Institutional support: RVO:68081766 Keywords : Magpies Pica pica * Great Reed Warblers Acrocephalus arundinaceus Subject RIV: EG - Zoology OBOR OECD: Ornithology Impact factor: 0.925, year: 2016

  20. Glow discharge electrolysis plasma initiated preparation of temperature/pH dual sensitivity reed hemicellulose-based hydrogels.

    Science.gov (United States)

    Zhang, Wenming; Zhu, Sha; Bai, Yunping; Xi, Ning; Wang, Shaoyang; Bian, Yang; Li, Xiaowei; Zhang, Yucang

    2015-05-20

    The temperature/pH dual sensitivity reed hemicellulose-based hydrogels have been prepared through glow discharge electrolysis plasma (GDEP). The effect of different discharge voltages on the temperature and pH response performance of reed hemicellulose-based hydrogels was inspected, and the formation mechanism, deswelling behaviors of reed hemicellulose-based hydrogels were also discussed. At the same time, infrared spectroscopy (FT-IR), scanning differential thermal analysis (DSC) and scanning electron microscope (SEM) were adopted to characterize the structure, phase transformation behaviors and microstructure of hydrogels. It turned out to be that all reed hemicellulose-based hydrogels had a double sensitivity to temperature and pH, and their phase transition temperatures were all approximately 33 °C, as well as the deswelling dynamics met the first model. In addition, the hydrogel (TPRH-3), under discharge voltage 600 V, was more sensitive to temperature and pH and had higher deswelling ratio. Copyright © 2015 Elsevier Ltd. All rights reserved.

  1. Annual cycle and migration strategies of a trans-Saharan migratory songbird : A geolocator study in the great reed warbler

    NARCIS (Netherlands)

    Lemke, Hilger W.; Tarka, Maja; Klaassen, Raymond H. G.; Akesson, Mikael; Bensch, Staffan; Hasselquist, Dennis; Hansson, Bengt

    2013-01-01

    Recent technological advancements now allow us to obtain geographical position data for a wide range of animal movements. Here we used light-level geolocators to study the annual migration cycle in great reed warblers (Acrocephalus arundinaceus), a passerine bird breeding in Eurasia and wintering in

  2. Prediction of biogas yield and its kinetics in reed canary grass using near infrared reflectance spectroscopy and chemometrics

    DEFF Research Database (Denmark)

    Kandel, Tanka Prasad; Gislum, René; Jørgensen, Uffe

    2013-01-01

    (SBY), specific methane yield (SMY) and kinetics of biogas yield (k-SBY) of reed canary grass (RCG) biomass. Dried and powdered RCG biomass with different level of maturity was used for biochemical composition analysis, batch assays and NIRS analysis. Calibration models were developed using partial...... to the models based on chemical composition....

  3. Integrated Canada-U.S. Power Sector Modeling with the Regional Energy Deployment System (ReEDS)

    Energy Technology Data Exchange (ETDEWEB)

    Martinez, A.; Eurek, K.; Mai, T.; Perry, A.

    2013-02-01

    The electric power system in North America is linked between the United States and Canada. Canada has historically been a net exporter of electricity to the United States. The extent to which this remains true will depend on the future evolution of power markets, technology deployment, and policies. To evaluate these and related questions, we modify the Regional Energy Deployment System (ReEDS) model to include an explicit representation of the grid-connected power system in Canada to the continental United States. ReEDS is unique among long-term capacity expansion models for its high spatial resolution and statistical treatment of the impact of variable renewable generation on capacity planning and dispatch. These unique traits are extended to new Canadian regions. We present example scenario results using the fully integrated Canada-U.S. version of ReEDS to demonstrate model capabilities. The newly developed, integrated Canada-U.S. ReEDS model can be used to analyze the dynamics of electricity transfers and other grid services between the two countries under different scenarios.

  4. A parametric study of powder holdups in a packed bed under ...

    African Journals Online (AJOL)

    Nafiisah

    coal in the form of powder accumulates in the lower part of the furnace and obstructs the gas and liquid flows. Therefore, there is an urgent need to understand the physics and aerodynamics of gas-powder flow in such systems to improve the flow conditions. In this article, the flow of gas and fines in a packed bed is studied.

  5. Giant reed (Arundo donax L. for biogas production: land use saving and nitrogen utilisation efficiency compared with arable crops

    Directory of Open Access Journals (Sweden)

    Federico Dragoni

    2015-12-01

    Full Text Available Aiming to improve the sustainability of biogas supply chains, the research for alternative feedstocks is a key issue and giant reed (Arundo donax L. is a promising no-food crop to be used in anaerobic digestion. In fact, giant reed is a perennial species characterised by low nutrient requirements and is able to provide promising biogas yields. Its suitability for anaerobic digestion is influenced by harvest time, since plant characteristics vary noticeably along the season. Moreover, ensiling is a storage technique that can assure a good preservation of the biomass over time, but also influence the methane yields. Therefore, the aim of this study was to assess the suitability for biogas production of giant reed silage, according to different cutting regimes, and to evaluate the efficiency in saving land and nitrogen for fuelling biogas plants, in comparison with maize and two sorghum varieties. Methane yields per hectare (Nm3 CH4 ha–1 were determined by multiplying the biochemical methane potential of each substrate by the aboveground biomass of the corresponding crop. The land use coefficient (LU, namely the land needed to fuel one kW power (ha kWe–1, was calculated from the estimated methane yields per hectare. Finally, nitrogen utilisation efficiency (NUtE, which is the ratio between the estimated methane yield and the nitrogen uptake per hectare (Nm3 CH4 kgN–1, was determined for each crop species and according to the harvest time and frequency of giant reed. Overall, a good suitability for ensiling was observed in giant reed. When harvested in September, the crop yielded about 9900 Nm3 CH4 ha–1, while in double harvest systems biomethane was about 12,000 Nm3 CH4 ha–1, +35% and +70% than maize and sorghum respectively. Moreover, giant reed under double harvest management was the most land-conservative option, as LU was about 0.22 ha kWe–1, while in annual crops it was about 0.35 ha kWe–1. The higher NUtE was observed in single

  6. Bed erosion control at 60 degree river confluence using vanes

    Science.gov (United States)

    Wuppukondur, Ananth; Chandra, Venu

    2017-04-01

    Confluences are common occurrences along natural rivers. Hydrodynamics at the confluence is complex due to merging of main and lateral flows with different characteristics. Bed erosion occurs at the confluence due to turbulence and also secondary circulation induced by centrifugal action of the lateral flow. The eroded sediment poses various problems in the river ecosystem including river bank failure. Reservoirs are majorly affected due to sediment deposition which reduces storage capacity. The bed erosion also endangers stability of pipeline crossings and bridge piers. The aim of this experimental study is to check the performance of vanes in controlling bed erosion at the confluence. Experiments are performed in a 600 confluence mobile bed model with a non-uniform sediment of mean particle size d50 = 0.28mm. Discharge ratio (q=ratio of lateral flow discharge to main flow discharge) is maintained as 0.5 and 0.75 with a constant average main flow depth (h) of 5cm. Vanes of width 0.3h (1.5cm) and thickness of 1 mm are placed along the mixing layer at an angle of 150, 300 and 600(with respect to main flow) to perform the experiments. Also, two different spacing of 2h and 3h (10cm and 15cm) between the vanes are used for conducting the experiments. A digital point gauge with an accuracy of ±0.1mm is used to measure bed levels and flow depths at the confluence. An Acoustic Doppler Velocitimeter (ADV) with a frequency of 25Hz and accuracy of ±1mm/s is used to measure flow velocities. Maximum scour depth ratio Rmax, which is ratio between maximum scour depth (Ds) and flow depth (h), is used to present the experimental results.From the experiments without vanes, it is observed that the velocities are increasing along the mixing layer and Rmax=0.82 and 1.06, for q=0.5 and 0.75, respectively. The velocities reduce with vanes since roughness increases along the mixing layer. For q=0.5 and 0.75, Rmax reduces to 0.62 and 0.7 with vanes at 2h spacing, respectively. Similarly

  7. Niche differentiation of two sympatric species of Microdochium colonizing the roots of common reed

    Directory of Open Access Journals (Sweden)

    Wirsel Stefan GR

    2011-10-01

    Full Text Available Abstract Background Fungal endophyte communities are often comprised of many species colonizing the same host. However, little is known about the causes of this diversity. On the one hand, the apparent coexistence of closely related species may be explained by the traditional niche differentiation hypothesis, which suggests that abiotic and/or biotic factors mediate partitioning. For endophytes, such factors are difficult to identify, and are therefore in most cases unknown. On the other hand, there is the neutral hypothesis, which suggests that stochastic factors may explain high species diversity. There is a need to investigate to what extent each of these hypotheses may apply to endophytes. Results The niche partitioning of two closely related fungal endophytes, Microdochium bolleyi and M. phragmitis, colonizing Phragmites australis, was investigated. The occurrences of each species were assessed using specific nested-PCR assays for 251 field samples of common reed from Lake Constance, Germany. These analyses revealed niche preferences for both fungi. From three niche factors assessed, i.e. host habitat, host organ and season, host habitat significantly differentiated the two species. M. bolleyi preferred dry habitats, whereas M. phragmitis prevailed in flooded habitats. In contrast, both species exhibited a significant preference for the same host organ, i.e. roots. Likewise the third factor, season, did not significantly distinguish the two species. Differences in carbon utilization and growth temperature could not conclusively explain the niches. The inclusion of three unrelated species of Ascomycota, which also colonize P. australis at the same locations, indicated spatio-temporal niche partitioning between all fungi. None of the species exhibited the same preferences for all three factors, i.e. host habitat, host organ, and time of the season. Conclusions The fungal species colonizing common reed investigated in this study seem to

  8. Giant reed growth and effects on soil biological fertility in assisted phytoremediation of an industrial polluted soil.

    Science.gov (United States)

    Fiorentino, N; Ventorino, V; Rocco, C; Cenvinzo, V; Agrelli, D; Gioia, L; Di Mola, I; Adamo, P; Pepe, O; Fagnano, M

    2017-01-01

    Phytoremediation is a cost-effective "green technology" that uses plants to improve the soil properties of polluted sites, preventing the dispersion of pollutants and reducing the mobility of potentially toxic elements (PTEs) through their adsorption and accumulation by roots or precipitation within the root zone. Being highly tolerant to pollutants and other abiotic stresses, giant reed (Arundo donax L.) is a suitable biomass crop for phytoremediation of contaminated soils. We report the results of a two-year open-air lysimeter study aimed at assessing the adaptability of giant reed to grow on industrial substrates polluted by Pb and Zn and at testing commercial humic acids from leonardite as improvers of plant performance. We evaluated giant reed potential for: 1) biomass production for energy or biomaterial recovery; 2) PTE phytoextraction and 3) soil fertility restoration. Chemical fertility was monitored by measuring soil C while soil biological fertility was estimated by quantifying the abundance of bacterial functional genes regulating nitrogen fixation (nifH) and nitrification (amoA). Giant reed above-ground growth on the polluted soils was slightly lower (-16%) than on a non-polluted soil, with a preferential storage of biomass in the rhizome acting as a survival strategy in limiting growing conditions. Humic acids improved plant stress tolerance and production levels. As aerial biomass (shoots) did not accumulate PTEs, the plant in question can be used for bioenergy or biopolymer production. In contrast, below-ground biomass (rhizomes) accumulated PTEs, and can thus be harvested and removed from soil to improve phytoremediation protocols and also used as industrial biofuel. Giant reed growth increased the abundance of N-cycling bacteria and soil C in the rhizospheric soil, as well as reduced soil Pb and Zn EDTA extractable fraction. Copyright © 2016 Elsevier B.V. All rights reserved.

  9. Coevolution of bed surface patchiness and channel morphology: 2. Numerical experiments

    Science.gov (United States)

    Nelson, Peter A.; McDonald, Richard R.; Nelson, Jonathan M.; Dietrich, William E.

    2015-01-01

    In gravel bed rivers, bed topography and the bed surface grain size distribution evolve simultaneously, but it is not clear how feedbacks between topography and grain sorting affect channel morphology. In this, the second of a pair of papers examining interactions between bed topography and bed surface sorting in gravel bed rivers, we use a two-dimensional morphodynamic model to perform numerical experiments designed to explore the coevolution of both free and forced bars and bed surface patches. Model runs were carried out on a computational grid simulating a 200 m long, 2.75 m wide, straight, rectangular channel, with an initially flat bed at a slope of 0.0137. Over five numerical experiments, we varied (a) whether an obstruction was present, (b) whether the sediment was a gravel mixture or a single size, and (c) whether the bed surface grain size feeds back on the hydraulic roughness field. Experiments with channel obstructions developed a train of alternate bars that became stationary and were connected to the obstruction. Freely migrating alternate bars formed in the experiments without channel obstructions. Simulations incorporating roughness feedbacks between the bed surface and flow field produced flatter, broader, and longer bars than simulations using constant roughness or uniform sediment. Our findings suggest that patches are not simply a by-product of bed topography, but they interact with the evolving bed and influence morphologic evolution.

  10. Experimental study of fluidized bed agglomeration of acerola powder

    Directory of Open Access Journals (Sweden)

    G. C. Dacanal

    2008-03-01

    Full Text Available The aim of this work was to study the main effects of acerola powder on fluidized bed agglomeration. A 2(4-1 fractional factoring design was used to evaluate the main operating conditions (fluidizing air temperature, fluidizing air velocity, atomizing air flow and height of nozzle in the bed. The mechanical and physicochemical product changes were determined by analysis of particle diameter, moisture content, wetting time and bed porosity. The particle enlargement by agglomeration occurred when the relative humidity in the bed increased and, thus, the moisture of the product increased. However, the excessive increase in relative humidity resulted in a decrease in yield, caused by caking and product incrustation. The consolidation of small granules resulted in an increase in the instant properties, decreasing the wetting time and increasing the solubility in a short period of agitation.

  11. Heat Transfer in a Fixed Bed of Straw Char

    DEFF Research Database (Denmark)

    Fjellerup, Jan Søren; Henriksen, Ulrik Birk; Jensen, Anker

    2003-01-01

    A model for the thermal conductivity of a straw char bed has been developed. The model extends the work of Yagi and Kunii to describe heat transfer in a bed of cylinders, using a relationship between the interparticle distance and the external porosity. To verify the model, thermal conductivity...... the experimental uncertainty over the range of conditions investigated. The heat transfer model was used in a parametric study to evaluate the effect of gas flow rate, particle diameter, porosity, and temperature on the thermal conductivity in a straw char bed....... experiments were performed on shredded and un-shredded straw char samples, varying particle size, bed packing (loose or dense), and temperature. Predictions with the model, using the measured external porosity and particle diameter as input parameters, are in agreement with measurements within...

  12. Air/water simulation of dryout in boiling particle beds

    International Nuclear Information System (INIS)

    Jones, K.

    1984-10-01

    Experimental studies of boiling in particle beds, representing reactor core debris, tend to be restricted to very small beds compared with what may be found in a real reactor accident situation. Experimental difficulties and costs are the restricting factors. There exists the possibility of getting around the problem by using air and water to simulate some of the many features of boiling in a particle bed. The idea has been examined experimentally. The results are inconclusive however, because they raise doubts about the interpretation of existing dry-out data. There is a possibility that flow maldistribution, which has not so far been allowed for, may be a key factor in the operation of a boiling bed. The subject requires further study. (author)

  13. Novel Polynomial Basis with Fast Fourier Transform and Its Application to Reed-Solomon Erasure Codes

    KAUST Repository

    Lin, Sian-Jheng

    2016-09-13

    In this paper, we present a fast Fourier transform (FFT) algorithm over extension binary fields, where the polynomial is represented in a non-standard basis. The proposed Fourier-like transform requires O(h lg(h)) field operations, where h is the number of evaluation points. Based on the proposed Fourier-like algorithm, we then develop the encoding/ decoding algorithms for (n = 2m; k) Reed-Solomon erasure codes. The proposed encoding/erasure decoding algorithm requires O(n lg(n)), in both additive and multiplicative complexities. As the complexity leading factor is small, the proposed algorithms are advantageous in practical applications. Finally, the approaches to convert the basis between the monomial basis and the new basis are proposed.

  14. The Giant Reed as an energy crop: assessing the energy requirements within its supply chain

    DEFF Research Database (Denmark)

    Rodias, Efthymis; Busato, P.; Bochtis, Dionysis

    2013-01-01

    Biomass energy is one form of renewable energy sources that are in the core of interesting for many researchers. There many different biomass sources that can be exploited for energy production, such as crop residues, waste materials, forestry residues and energy crops. Regarding energy crops......, there are many different types of crops significantly varies in terms of energy potential yields, production and provision methods, etc. To this end, a thoroughly assessment of the energy inputs and outputs of each potential energy crop is necessary. In this paper, the Giant Reed is evaluated energetically...... as a potential energy crop. The assessment regards a 10 year period. The considered energy elements include direct inputs (e.g. fuel consumption) as well as indirect inputs (e.g. embodied energy of materials and machinery). According to the results, the balance between the estimated total energy input...

  15. Sensory systems for a control rod position using reed switches for the integral reactor

    International Nuclear Information System (INIS)

    Yu, J. Y.; Choi, S.; Kim, J. H.; Lee, D. J.

    2007-01-01

    The system-integrated modular advanced reactor (SMART) currently under development at the Korea Atomic Energy Research Institute is being designed with a soluble boron free operation and the use of nuclear heating for the reactor start-up. These design features require a Control Element Drive Mechanism (CEDM) for the SMART to have a fine-step movement capability as well as a high reliability for a fine reactivity control. Also the reliability and accuracy of the information for the control rod position is very important to the reactor safety as well as the design of the core protection system. The position indicator is classified as a Class 1E component because the rod position signal of the position indicator is used in the safety related systems. Therefore it will be separated from the control systems to the extent that a failure of any single control system component of a channel and shall have sufficient independence, redundancy, and testability to perform its safety functions assuming a single failure. The position indicator is composed of a permanent magnet, reed switches and a voltage divider. Four independent position indicators around the upper pressure housing provide an indication of the position of a control rod comprising of a permanent magnet with a magnetic field concentrator which moves with the extension shaft connected to the control rod. The zigzag arranged reed switches are positioned along a line parallel to the path of the movement of the permanent magnet and it is activated selectively when the permanent magnet passes by. A voltage divider electrically connected to the reed switches provides a signal commensurate with the position of the control rod. The signal may then be transmitted to a position indicating device. In order to monitor the operating condition of the rotary step motor of CEDM, the angular position detector was installed at the top of the rotary step motor by means of connecting between the planetary gear and the rotating

  16. Error suppression via complementary gauge choices in Reed-Muller codes

    Science.gov (United States)

    Chamberland, Christopher; Jochym-O'Connor, Tomas

    2017-09-01

    Concatenation of two quantum error-correcting codes with complementary sets of transversal gates can provide a means toward universal fault-tolerant quantum computation. We first show that it is generally preferable to choose the inner code with the higher pseudo-threshold to achieve lower logical failure rates. We then explore the threshold properties of a wide range of concatenation schemes. Notably, we demonstrate that the concatenation of complementary sets of Reed-Muller codes can increase the code capacity threshold under depolarizing noise when compared to extensions of previously proposed concatenation models. We also analyze the properties of logical errors under circuit-level noise, showing that smaller codes perform better for all sampled physical error rates. Our work provides new insights into the performance of universal concatenated quantum codes for both code capacity and circuit-level noise.

  17. RAID-6 reed-solomon codes with asymptotically optimal arithmetic complexities

    KAUST Repository

    Lin, Sian-Jheng

    2016-12-24

    In computer storage, RAID 6 is a level of RAID that can tolerate two failed drives. When RAID-6 is implemented by Reed-Solomon (RS) codes, the penalty of the writing performance is on the field multiplications in the second parity. In this paper, we present a configuration of the factors of the second-parity formula, such that the arithmetic complexity can reach the optimal complexity bound when the code length approaches infinity. In the proposed approach, the intermediate data used for the first parity is also utilized to calculate the second parity. To the best of our knowledge, this is the first approach supporting the RAID-6 RS codes to approach the optimal arithmetic complexity.

  18. Gas-liquid flow filed in agitated vessels

    International Nuclear Information System (INIS)

    Hormazi, F.; Alaie, M.; Dabir, B.; Ashjaie, M.

    2001-01-01

    Agitated vessels in form of sti reed tank reactors and mixed ferment ors are being used in large numbers of industry. It is more important to develop good, and theoretically sound models for scaling up and design of agitated vessels. In this article, two phase flow (gas-liquid) in a agitated vessel has been investigated numerically. A two-dimensional computational fluid dynamics model, is used to predict the gas-liquid flow. The effects of gas phase, varying gas flow rates and variation of bubbles shape on flow filed of liquid phase are investigated. The numerical results are verified against the experimental data

  19. Reed Reactor Facility annual report, September 1, 1994--August 31, 1995

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1995-12-31

    This report covers the period from September 1, 1994 to August 31, 1995. Information contained in this report is intended to fulfill several purposes including the reporting requirements of the US Nuclear Regulatory Commission (USNRC), the US Department of Energy (USDOE), and the Oregon Department of Energy (ODOE). Highlights of the last year include: (1) The number of new licensed student operators more than replaced the number of graduating seniors. Seven Reed College seniors used the reactor as part of their thesis projects. (2) The facility has been extraordinarily successful in obtaining donated equipment from Portland General Electric, US Department of Energy, Precision Castparts, Tektronix, and other sources. Battelle (Pacific Northwest Laboratory) has been generous in lending valuable equipment to the college. (3) The facility is developing more paid work. Income in the past academic year was much greater than the previous year, and next year should increase by even more. Additionally, the US Department of Energy`s Reactor-Use Sharing grant increased significantly this year. During the year, the reactor was operated 225 separate times on 116 days. The total energy production was 24.6 MW-hours. The reactor staff consists of a Director, an Assistant Director, a contract Health Physicist, and approximately fifteen Reed College undergraduate students as hourly employees. All radiation exposures to individuals during this year were well below one percent of the federal limits. There were no releases of liquid radioactive material from the facility and airborne releases (primarily {sup 41}Ar) were well within regulatory limits. No radioactive waste was shipped from the facility during this period.

  20. The use of reed canary grass and giant miscanthus in the phytoremediation of municipal sewage sludge.

    Science.gov (United States)

    Antonkiewicz, Jacek; Kołodziej, Barbara; Bielińska, Elżbieta Jolanta

    2016-05-01

    The application of municipal sewage sludge on energy crops is an alternative form of recycling nutrients, food materials, and organic matter from waste. Municipal sewage sludge constitutes a potential source of heavy metals in soil, which can be partially removed by the cultivation of energy crops. The aim of the research was to assess the effect of municipal sewage sludge on the uptake of heavy metals by monocotyledonous energy crops. Sewage sludge was applied at doses of 0, 10, 20, 40, and 60 Mg DM · ha(-1) once, before the sowing of plants. In a 6-year field experiment, the effect of four levels of fertilisation with sewage sludge on the uptake of heavy metals by two species of energy crops, reed canary grass (Phalaris arundinacea L.) of 'Bamse' cultivar and giant miscanthus (Miscanthus × giganteus GREEF et DEU), was analysed. It was established that the increasing doses of sewage sludge had a considerable effect on the increase in biomass yield from the tested plants. Due to the increasing doses of sewage sludge, a significant increase in heavy metals content in the energy crops was recorded. The heavy metal uptake with the miscanthus yield was the highest at a dose of 20 Mg DM · ha(-1), and at a dose of 40 Mg DM · ha(-1) in the case of reed canary grass. Research results indicate that on account of higher yields, higher bioaccumulation, and higher heavy metal uptake, miscanthus can be selected for the remediation of sewage sludge.

  1. Reed Reactor Facility annual report, September 1, 1994--August 31, 1995

    International Nuclear Information System (INIS)

    1995-01-01

    This report covers the period from September 1, 1994 to August 31, 1995. Information contained in this report is intended to fulfill several purposes including the reporting requirements of the US Nuclear Regulatory Commission (USNRC), the US Department of Energy (USDOE), and the Oregon Department of Energy (ODOE). Highlights of the last year include: (1) The number of new licensed student operators more than replaced the number of graduating seniors. Seven Reed College seniors used the reactor as part of their thesis projects. (2) The facility has been extraordinarily successful in obtaining donated equipment from Portland General Electric, US Department of Energy, Precision Castparts, Tektronix, and other sources. Battelle (Pacific Northwest Laboratory) has been generous in lending valuable equipment to the college. (3) The facility is developing more paid work. Income in the past academic year was much greater than the previous year, and next year should increase by even more. Additionally, the US Department of Energy's Reactor-Use Sharing grant increased significantly this year. During the year, the reactor was operated 225 separate times on 116 days. The total energy production was 24.6 MW-hours. The reactor staff consists of a Director, an Assistant Director, a contract Health Physicist, and approximately fifteen Reed College undergraduate students as hourly employees. All radiation exposures to individuals during this year were well below one percent of the federal limits. There were no releases of liquid radioactive material from the facility and airborne releases (primarily 41 Ar) were well within regulatory limits. No radioactive waste was shipped from the facility during this period

  2. The Importance of Splat Events to the Spatiotemporal Structure of Near-Bed Fluid Velocity and Bed Load Motion Over Bed Forms: Laboratory Experiments Downstream of a Backward Facing Step

    Science.gov (United States)

    Leary, K. C. P.; Schmeeckle, M. W.

    2017-12-01

    Flow separation/reattachment on the lee side of alluvial bed forms is known to produce a complex turbulence field, but the spatiotemporal details of the associated patterns of bed load sediment transported remain largely unknown. Here we report turbulence-resolving, simultaneous measurements of bed load motion and near-bed fluid velocity downstream of a backward facing step in a laboratory flume. Two synchronized high-speed video cameras simultaneously observed bed load motion and the motion of neutrally buoyant particles in a laser light sheet 6 mm above the bed at 250 frames/s downstream of a 3.8 cm backward facing step. Particle Imaging Velocimetry (PIV) and Acoustic Doppler Velocimetry (ADV) were used to characterize fluid turbulent patterns, while manual particle tracking techniques were used to characterize bed load transport. Octant analysis, conducted using ADV data, coupled with Markovian sequence probability analysis highlights differences in the flow near reattachment versus farther downstream. Near reattachment, three distinct flow patterns are apparent. Farther downstream we see the development of a dominant flow sequence. Localized, intermittent, high-magnitude transport events are more apparent near flow reattachment. These events are composed of streamwise and cross-stream fluxes of comparable magnitudes. Transport pattern and fluid velocity data are consistent with the existence of permeable "splat events," wherein a volume of fluid moves toward and impinges on the bed (sweep) causing a radial movement of fluid in all directions around the point of impingement (outward interaction). This is congruent with flow patterns, identified with octant analysis, proximal to flow reattachment.

  3. Pyrolysis reactor and fluidized bed combustion chamber

    Science.gov (United States)

    Green, Norman W.

    1981-01-06

    A solid carbonaceous material is pyrolyzed in a descending flow pyrolysis reactor in the presence of a particulate source of heat to yield a particulate carbon containing solid residue. The particulate source of heat is obtained by educting with a gaseous source of oxygen the particulate carbon containing solid residue from a fluidized bed into a first combustion zone coupled to a second combustion zone. A source of oxygen is introduced into the second combustion zone to oxidize carbon monoxide formed in the first combustion zone to heat the solid residue to the temperature of the particulate source of heat.

  4. COMPUTATIONAL MODELING OF CIRCULATING FLUIDIZED BED REACTORS

    Energy Technology Data Exchange (ETDEWEB)

    Ibrahim, Essam A

    2013-01-09

    Details of numerical simulations of two-phase gas-solid turbulent flow in the riser section of Circulating Fluidized Bed Reactor (CFBR) using Computational Fluid Dynamics (CFD) technique are reported. Two CFBR riser configurations are considered and modeled. Each of these two riser models consist of inlet, exit, connecting elbows and a main pipe. Both riser configurations are cylindrical and have the same diameter but differ in their inlet lengths and main pipe height to enable investigation of riser geometrical scaling effects. In addition, two types of solid particles are exploited in the solid phase of the two-phase gas-solid riser flow simulations to study the influence of solid loading ratio on flow patterns. The gaseous phase in the two-phase flow is represented by standard atmospheric air. The CFD-based FLUENT software is employed to obtain steady state and transient solutions for flow modulations in the riser. The physical dimensions, types and numbers of computation meshes, and solution methodology utilized in the present work are stated. Flow parameters, such as static and dynamic pressure, species velocity, and volume fractions are monitored and analyzed. The differences in the computational results between the two models, under steady and transient conditions, are compared, contrasted, and discussed.

  5. Wave interaction with large roughness elements on an impermeable sloping bed

    DEFF Research Database (Denmark)

    Jensen, Bjarne; Christensen, Erik Damgaard; Sumer, B. Mutlu

    2012-01-01

    The present paper presents the results of an experimental and numerical investigation of the flow between large roughness elements on a steep sloping impermeable bed during wave action. The setup is designed to resemble a breakwater structure. The work is part of a study where the focus is on the......The present paper presents the results of an experimental and numerical investigation of the flow between large roughness elements on a steep sloping impermeable bed during wave action. The setup is designed to resemble a breakwater structure. The work is part of a study where the focus...... and successively repeated with a porous bed. In this paper the focus is on the impermeable bed. Results are obtained experimentally for flow and turbulence between the roughness elements on the sloping bed. Numerical simulations have reproduced the experimental results with good agreements and can hereby add more...

  6. Influence of flow velocity on the removal of faecal coliforms in horizontal subsurface flow constructed wetland.

    Science.gov (United States)

    Lohay, W S; Lyimo, T J; Njau, K N

    2012-01-01

    In order to determine the influence of flow velocity on the removal of faecal coliforms (FC) in constructed wetlands (CWs), removal rate constants of FC (k(FC)) were studied at various flow velocities (u). Membrane filtration technique was used during analysis. Values of k(FC) were determined using Reed's equation of pathogen removal; the results were compared with the plug flow equation. According to Reed's equation, k(FC) values ranged from 1.6 day⁻¹ at a velocity of 4 m/day to 34.5 day⁻¹ at a velocity of 42.9 m/day. The removal rates correlated positively with flow velocity (r = 0.84, p < 0.05). On assuming a plug flow equation, removal rates constants ranged from 0.77 to 11.69 day⁻¹; a more positive correlation (r = 0.93, p < 0.05) was observed. Optimum removal rate constants were observed for the velocity ranging 36 to 43 m/day. Generally, the increase of flow velocity improved FC removal rate constants: implying that pathogen removals are influenced by diffusion of the microorganisms into the biofilms on CW media. The velocity dependent approach together with the plug flow equation is therefore proposed for incorporation in the design of CW in a tropical climate where temperature variations are minor.

  7. Numerical investigation of bed morphodynamics due to a hydrokinetic turbine

    Science.gov (United States)

    Yang, X.; Khosronejad, A.; Sotiropoulos, F.

    2013-12-01

    Marine and hydrokinetic (MHK) energy comprises an important source of clean and renewable energy. The beds of natural waterways are usually erodible. The hydrokinetic turbines affect the sediment transport, which, on the other hand, also influences the performance of hydrokinetic turbines. A powerful computational framework for simulating marine and hydrokinetic (MHK) turbine arrays mounted in complex river bathymetry with sediment transport has been developed and validated by our group. In this work we apply this method to simulate the turbulent flow over a hydrokinetic turbine mounted in an open channel with erodible bed. Preliminary results show qualitatively good agreement with the experiment. Detailed comparison with measurements and analysis of the simulation results will be presented in the conference. Contours of the instantaneous streamwise velocity for flow past a hydrokinetic turbine mounted on an erodible bed.

  8. Effectiveness of Bed Bug Pesticides

    Science.gov (United States)

    Before EPA allows a bed bug claim on a label, the product must be supported by data showing it will kill bed bugs when applied according to the label. Also consider factors such as extent of infestation, site preparation, and insect life stages.

  9. Turning patients over in bed

    Science.gov (United States)

    ... this page: //medlineplus.gov/ency/patientinstructions/000426.htm Turning patients over in bed To use the sharing features on this page, ... Patient The following steps should be followed when turning a patient: If you can, raise the bed to a level that reduces back strain for ...

  10. Air gasification of rice husk in bubbling fluidized bed reactor with bed heating by conventional charcoal.

    Science.gov (United States)

    Makwana, J P; Joshi, Asim Kumar; Athawale, Gaurav; Singh, Dharminder; Mohanty, Pravakar

    2015-02-01

    An experimental study of air gasification of rice husk was conducted in a bench-scale fluidized bed gasifier (FBG) having 210 mm diameter and 1600 mm height. Heating of sand bed material was performed using conventional charcoal fuel. Different operating conditions like bed temperature, feeding rate and equivalence ratio (ER) varied in the range of 750-850 °C, 25-31.3 kg/h, and 0.3-0.38, respectively. Flow rate of air was kept constant (37 m(3)/h) during FBG experiments. The carbon conversion efficiencies (CCE), cold gas efficiency, and thermal efficiency were evaluated, where maximum CCE was found as 91%. By increasing ER, the carbon conversion efficiency was decreased. Drastic reduction in electric consumption for initial heating of gasifier bed with charcoal compared to ceramic heater was ∼45%. Hence rice husk is found as a potential candidate to use directly (without any processing) in FBG as an alternative renewable energy source from agricultural field. Copyright © 2014 Elsevier Ltd. All rights reserved.

  11. Business Case Analysis of the Walter Reed Army Medical Center Medical/Surgical Prime Vendor Generation III Service Level Electron Program

    National Research Council Canada - National Science Library

    Markot, Peter B

    2007-01-01

    ...) staffing and medical/surgical services offered under the Prime Vendor (PV) Generation III contract would provide the best supply chain management solution for Walter Reed Army Medical Center (WRAMC...

  12. Hatchling sex ratio and female mating status in the great reed warbler, Acrocephalus arundinaceus (Aves, Passeriformes): further evidence for offspring sex ratio manipulation

    Czech Academy of Sciences Publication Activity Database

    Trnka, A.; Prokop, P.; Kašová, M.; Sobeková, Karolina; Kocian, Ľ.

    2012-01-01

    Roč. 79, č. 2 (2012), s. 212-217 ISSN 1125-0003 Institutional support: RVO:68081766 Keywords : Great reed warbler * sex ratio * social polygyny Subject RIV: EG - Zoology Impact factor: 0.890, year: 2012

  13. Discrete element study of granulation in a spout-fluidized bed

    NARCIS (Netherlands)

    Link, J.M.; Godlieb, W.; Deen, N.G.; Kuipers, J.A.M.

    2007-01-01

    In this work a discrete element model (DEM) is presented for the description of the gas–liquid–solid flow in a spout-fluidized bed including all relevant phenomena for the study of granulation. The model is demonstrated for the case of a granulation process in a flat spout-fluidized bed, containing

  14. An analysis of mussel bed habitats in the Dutch Wadden Sea

    NARCIS (Netherlands)

    Brinkman, A.G.; Dankers, N.M.J.A.; Stralen, van M.

    2002-01-01

    A habitat suitability analysis for littoral mussel beds in the Dutch Wadden Sea was carried out. The analysis was based on the presence of mussel beds in the years 1960-1970, and a number of environmental characteristics: wave action, flow velocity, median grain size, emersion times and distance to

  15. Predicting Coarse Sediment Transport from Patchy Beds in Ephemeral Channels

    Science.gov (United States)

    2012-04-01

    basin fill of Plio-Pleistocene plutonic or volcanic clasts approaching 900 m in thickness. Surficial ERDC/GSL TR-12-17 7 sediments were likely...flow velocity, D84 is grain size in which 84% of the channel bed grains are finer. The variable a is a channel shape factor defined as h R a D

  16. The porosity in a fluidized bed heat transfer model

    NARCIS (Netherlands)

    Visser, G; Visser, G.; Valk, M.

    1993-01-01

    A mathematical model of heat transfer between a fluidized bed and an immersed surface and a model of gas flow and porosity, both recently published, were combined and further modified in the area of low velocities where the particle convective component of heat transfer is low or neglectable.

  17. Extracting Silicon Product From Fluidized-Bed Reactors

    Science.gov (United States)

    Hsu, G. C.; Rohatgi, N. K.; Morrison, A. D.

    1986-01-01

    Silicon particles continuously removed from bottom of fluidizedbed reactor when grown to large size. In reactor, silane (SiH4) flows through bed of small silicon seed particles at temperature of 650 degrees to 700 degrees C. Silane decomposes into silicon vapor and hydrogen gas, and vapor deposits as solid on seed particles. With withdrawal system, reactor operates continuously.

  18. Decreased distensibility of a passive vascular bed in diabetes mellitus

    DEFF Research Database (Denmark)

    Faris, I; Agerskov, K; Henrikson, O

    1982-01-01

    This study was undertaken to determine whether the distensibility of a passive vascular bed is reduced in Type 1 (insulin-dependent) diabetic patients with microangiopathy. The change in blood flow induced by 45 degrees head-up tilting was studied in two systems: (a) following maximal ischaemic...

  19. On the effect of segregation on intense bimodal bed load

    Directory of Open Access Journals (Sweden)

    Zrostlík Štěpán

    2017-01-01

    Full Text Available Open-channel two-phase flow above a granular mobile bed is studied experimentally and theoretically. In the two-phase flow, water serves as a carrying liquid for plastic grains transported as collisional contact load in the upper-stage plane bed regime. The investigation evaluates friction- and transport characteristics of the flow under the condition of intense collisional transport of grains and links them with the internal structure of the two-phase flow. The paper focusses on the effect of bimodal solids (mixed two fractions of grains of similar density and different size and shape on the flow characteristics and internal structure. Hence, experimental results obtained for the bimodal mixture are compared with results for individual grain fractions. The experiments show that the bimodal character of the transported solids affects the layered internal structure of the flow as a result of fraction segregation due primarily to gravity (kinetic sieving during transport. The segregation also affects the friction- and transport characteristics of intense bed load. In the paper, the effects are described and quantified.

  20. On the effect of segregation on intense bimodal bed load

    Science.gov (United States)

    Zrostlík, Štěpán; Matoušek, Václav

    Open-channel two-phase flow above a granular mobile bed is studied experimentally and theoretically. In the two-phase flow, water serves as a carrying liquid for plastic grains transported as collisional contact load in the upper-stage plane bed regime. The investigation evaluates friction- and transport characteristics of the flow under the condition of intense collisional transport of grains and links them with the internal structure of the two-phase flow. The paper focusses on the effect of bimodal solids (mixed two fractions of grains of similar density and different size and shape) on the flow characteristics and internal structure. Hence, experimental results obtained for the bimodal mixture are compared with results for individual grain fractions. The experiments show that the bimodal character of the transported solids affects the layered internal structure of the flow as a result of fraction segregation due primarily to gravity (kinetic) sieving during transport. The segregation also affects the friction- and transport characteristics of intense bed load. In the paper, the effects are described and quantified.

  1. Evaluating the Value of High Spatial Resolution in National Capacity Expansion Models using ReEDS: Preprint

    Energy Technology Data Exchange (ETDEWEB)

    Krishnan, Venkat; Cole, Wesley

    2016-07-01

    Power sector capacity expansion models (CEMs) have a broad range of spatial resolutions. This paper uses the Regional Energy Deployment System (ReEDS) model, a long-term national scale electric sector CEM, to evaluate the value of high spatial resolution for CEMs. ReEDS models the United States with 134 load balancing areas (BAs) and captures the variability in existing generation parameters, future technology costs, performance, and resource availability using very high spatial resolution data, especially for wind and solar modeled at 356 resource regions. In this paper we perform planning studies at three different spatial resolutions--native resolution (134 BAs), state-level, and NERC region level--and evaluate how results change under different levels of spatial aggregation in terms of renewable capacity deployment and location, associated transmission builds, and system costs. The results are used to ascertain the value of high geographically resolved models in terms of their impact on relative competitiveness among renewable energy resources.

  2. Contribution to harmonic balance calculations of self-sustained periodic oscillations with focus on single-reed instruments.

    Science.gov (United States)

    Farner, Snorre; Vergez, Christophe; Kergomard, Jean; Lizée, Aude

    2006-03-01

    The harmonic balance method (HBM) was originally developed for finding periodic solutions of electronical and mechanical systems under a periodic force, but has been adapted to self-sustained musical instruments. Unlike time-domain methods, this frequency-domain method does not capture transients and so is not adapted for sound synthesis. However, its independence of time makes it very useful for studying any periodic solution, whether stable or unstable, without care of particular initial conditions in time. A computer program for solving general problems involving nonlinearly coupled exciter and resonator, HARMBAL, has been developed based on the HBM. The method as well as convergence improvements and continuation facilities are thoroughly presented and discussed in the present paper. Applications of the method are demonstrated, especially on problems with severe difficulties of convergence: the Helmholtz motion (square signals) of single-reed instruments when no losses are taken into account, the reed being modeled as a simple spring.

  3. Next generation fluidized bed granulator automation.

    Science.gov (United States)

    Rantanen, J; Känsäkoski, M; Suhonen, J; Tenhunen, J; Lehtonen, S; Rajalahti, T; Mannermaa, J P; Yliruusi, J

    2000-05-06

    A system for fluidized bed granulator automation with in-line multichannel near infrared (NIR) moisture measurement and a unique air flow rate measurement design was assembled, and the information gained was investigated. The multivariate process data collected was analyzed using principal component analysis (PCA). The test materials (theophylline and microcrystalline cellulose) were granulated and the calibration behavior of the multichannel NIR set-up was evaluated against full Fourier Transform (FT) NIR spectra. Accurate and reliable process air flow rate measurement proved critical in controlling the granulation process. The process data describing the state of the process was projected in two dimensions, and the information from various trend charts was outlined simultaneously. The absorbence of test material at correction wavelengths (NIR region) and the nature of material-water interactions affected the detected in-line NIR water signal. This resulted in different calibration models for the test materials. Development of process analytical methods together with new data visualization algorithms creates new tools for in-process control of the fluidized bed granulation.

  4. Air Distributor Designs for Fluidized Bed Combustors: A Review

    Directory of Open Access Journals (Sweden)

    A. Shukrie

    2016-06-01

    Full Text Available Fluidized bed combustion (FBC has been recognized as one of the suitable technologies for converting a wide variety of biomass fuels into energy. One of the key factors affecting the successful operation of fluidized bed combustion is its distributor plate design. Therefore, the main purpose of this article is to provide a critical overview of the published studies that are relevant to the characteristics of different fluidized bed air distributor designs. The review of available works display that the type of distributor design significantly affects the operation of the fluidized bed i.e., performance characteristics, fluidization quality, air flow dynamics, solid pattern and mixing caused by the direction of air flow through the distributors. Overall it is observed that high pressure drop across the distributor is one of the major draw backs of the current distributor designs. However, fluidization was stable in a fluidized bed operated at a low perforation ratio distributor due to the pressure drop across the distributor, adequate to provide uniform gas distribution. The swirling motion produced by the inclined injection of gas promotes lateral dispersion and significantly improves fluidization quality. Lastly, the research gaps are highlighted for future improvement consideration on the development of efficient distributor designs.

  5. The state of development of multilayer sand bed filters

    International Nuclear Information System (INIS)

    Jordan, S.; Schikarski, W.

    1977-01-01

    The state of development of multilayer sand bed filters may be described as follows: 1) Sand bed filters are generally suitable for the filtration of aggressive aerosols, in particular in cases of additional thermal loads, pressure peaks (fire safety, earthquakes). 2) Sand bed filters permit high flow rates, GfK filters (GfK = Gesellschaft fuer Kernforschung) reach 10 m 3 /min x m 2 with charges of more than 1 kg/m 2 and a separating efficiency > 99%. (use as pre-filters for the separation of large amounts of aerosols). 3) With proper optimization, the separating efficiency is better than that of class S filters (99.97%), while no significant reduction of the charge is required. 4) Exchange of sand bed filters is possible with a suitable vertical arrangement of the sand layers. 5) Sand bed filters may be combined with class S filters. The experience so far with sand bed filters was gained on the basis of experiments with aerosols from metal combustion. (orig./HP) [de

  6. Long-term ionizing radiation impact on seed progeny of common reed in water bodies of the Chernobyl exclusive zone

    International Nuclear Information System (INIS)

    Shevtsova, N.L.; Yavnyuk, A.A.; Gudkov, D.Yi.

    2012-01-01

    Results of the investigation of common reed's (Phragmites australis (Trin) Ex. Steud.) biological characteristics under conditions of long-term ionizing radiation impact are represented. Indices of seeds' vitality and disorders are analyzed. Low vitality indices, significant ontogenesis disorders, and high percent of abnormalities of germs are determined in water bodies, where littoral plants receive the absorbed dose in a low-dose range of 1-12 cGy year -1 .

  7. Torsion testing of bed joints

    DEFF Research Database (Denmark)

    Hansen, Klavs Feilberg; Pedersen, Carsten Mørk

    2008-01-01

    be carried out directly in a normal testing machine. The torsion strength is believed to be the most important parameter in out-of-plane resistance of masonry walls subjected to bending about an axis perpendicular to the bed joints. The paper also contains a few test results from bending of small walls about...... an axis perpendicular to the bed joints, which indicate the close connection between these results and results from torsion tests. These characteristics make the torsion strength well suited to act as substitute parameter for the bending strength of masonry about an axis perpendicular to the bed joints....

  8. Computational fluid dynamic modeling of fluidized-bed polymerization reactors

    Energy Technology Data Exchange (ETDEWEB)

    Rokkam, Ram [Iowa State Univ., Ames, IA (United States)

    2012-01-01

    Polyethylene is one of the most widely used plastics, and over 60 million tons are produced worldwide every year. Polyethylene is obtained by the catalytic polymerization of ethylene in gas and liquid phase reactors. The gas phase processes are more advantageous, and use fluidized-bed reactors for production of polyethylene. Since they operate so close to the melting point of the polymer, agglomeration is an operational concern in all slurry and gas polymerization processes. Electrostatics and hot spot formation are the main factors that contribute to agglomeration in gas-phase processes. Electrostatic charges in gas phase polymerization fluidized bed reactors are known to influence the bed hydrodynamics, particle elutriation, bubble size, bubble shape etc. Accumulation of electrostatic charges in the fluidized-bed can lead to operational issues. In this work a first-principles electrostatic model is developed and coupled with a multi-fluid computational fluid dynamic (CFD) model to understand the effect of electrostatics on the dynamics of a fluidized-bed. The multi-fluid CFD model for gas-particle flow is based on the kinetic theory of granular flows closures. The electrostatic model is developed based on a fixed, size-dependent charge for each type of particle (catalyst, polymer, polymer fines) phase. The combined CFD model is first verified using simple test cases, validated with experiments and applied to a pilot-scale polymerization fluidized-bed reactor. The CFD model reproduced qualitative trends in particle segregation and entrainment due to electrostatic charges observed in experiments. For the scale up of fluidized bed reactor, filtered models are developed and implemented on pilot scale reactor.

  9. Intercropping of reed canary grass, phalaris arundinacea l., with legumes can cut costs for n-fertilization

    Energy Technology Data Exchange (ETDEWEB)

    Palmborg, Cecilia; Lindvall, Eva (Swedish Univ. of Agricultural Sciences, Dept. of Agricultural Research for Northern Sweden, Umeaa (Sweden)), e-mail: eva.lindvall@njv.slu.se

    2010-07-15

    In a field experiment close to Oestersund in mid Sweden reed canary grass was intercropped with barley, Alsike clover, Trifolium hybridum L., red clover, T. pratense L., goats rue, Galega orientalis L. or a combination of red clover and goats rue. There were also three fertilization treatments: A: Recommended amounts of N, P and K. B: Recommended amounts of P and K and half amount of N. C: Sewage sludge application before sowing (establishment year) and recommended amounts of P and K and half amount of N. The biomass was lower where reed canary grass had been undersown in barley, and higher with full N-fertilization than with half N-fertilization. However there were no significant differences between legume intercrops with half N-fertilization and pure reed canary grass with full Nfertilization. Alsike clover was the most productive legume, followed by red clover. The amount of nitrogen fixed by the legumes was less with full N-fertilization (29 kg/ha as a mean) than with half N-fertilization (38 kg/ha). Intercropping with legumes could substitute half of the N in fertilization but similar experiments in other parts of Sweden has shown that there is a higher risk of weed problems

  10. Short communication. Natural durability of reed (Phragmites australis) against wood decay organisms: relation to other forest species

    Energy Technology Data Exchange (ETDEWEB)

    Troya, M. T.; Rubio, F.; Prieto, M. J.; Lorenzo, D.; Fernandez-Cabo, J. L.; Schoftner, R.

    2009-07-01

    This work presents the research carried out to determine the natural durability of reed (Phragmites communis) from the Ferto region of Hungary against wood decay organisms, with the objective of obtaining information to be used as a constituent element in outdoor use, and in particular, in a viable and sustainable motor way noise barrier. Phragmites communis is a large perennial grass of considerable size which grows in temperate and tropical wetland zones throughout the world. Its growth is expansive and it frequently invades wetlands where it competes with the native species and therefore requires regular removal so that an excess of organic material is not produced in the habitat. In addition, the invasion by this plant of polluted waters also appears to have a beneficial effect, so it can be used as a natural water purifier and thus has a potential use as a purification method for wetlands contaminated by agricultural practices. Due to the need for its periodic extraction, its possible use as a construction material, although in a secondary role, gives it an added value for which further scientific study is required. In the absence of a reference Standard and being reed a lignocellulose material, the study of its natural durability has been based on the existing Standards for wood. The tests show that Hungarian reed has a high level of durability against some fungi and other wood decay organisms. (Author) 21 refs.

  11. STUCTURE OF PULSED BED

    Directory of Open Access Journals (Sweden)

    I. A. Bokun

    2014-01-01

    Full Text Available The structure of pulsed layer is proposed which can be suggested as a state of particulates that is blown by intermittent gas flow with speed which has the force to start material moving. Layer during one cycle is in a suspension, falling down and immobile state resulting in changes of particles arrangement as well as ways of gas flowing through layer. Moreover, it allows carrying out effective interphase heat exchange even adamant real granulation.The process of formation of impact flows is considered aw well as their influence on formation of air bubbles in pulsed layer. At startup of air blast the balance between the force of hydro-dynamic resistance is broken, on one side, and forces of gravity, particles inertia and their links with walls on the other side. The layer is transferred in the state of pulsed pseudo-fluidization, and presents gas-disperse mixture, inside of which impulse of pressure increasing is spreading to all sides as pressure waves (compression. These waves are the sources of impact flows’ formation, the force of which is two times more than during the stationary flow.The waves of pressure are divided into weak and strong ones depending on movement velocity within gas-disperse system. Weak waves are moving with a sound speed and strong ones in active phase of pulsed layer are moving over the speed of sound limit within gas-disperse system. The peculiarity of strong wave is that parameters of system (pressure, density and others are changing in discrete steps.The article describes the regime of layer’s falling down in the passive stage of cycle, which begins after finishing of gas impulse action. And suspension layer of moving up granular material is transferred in the state of falling resulting in change of the layer structure.

  12. Divergence at the edges: peripatric isolation in the montane spiny throated reed frog complex.

    Science.gov (United States)

    Lawson, Lucinda P; Bates, John M; Menegon, Michele; Loader, Simon P

    2015-07-01

    Peripatric speciation and peripheral isolation have uncertain importance in species accumulation, and are largely overshadowed by assumed dominance of allopatric modes of speciation. Understanding the role of different speciation mechanisms within biodiversity hotspots is central to understanding the generation of biological diversity. Here, we use a phylogeographic analysis of the spiny-throated reed frogs and examine sister pairings with unbalanced current distributional ranges for characteristics of peripatric speciation. We further investigate whether forest/grassland mosaic adapted species are more likely created through peripatric speciation due to instability of this habitat type. We reconstructed a multi-locus molecular phylogeny of spiny-throated reed frogs which we then combined with comparative morphologic data to delimit species and analyze historical demographic change; identifying three new species. Three potential peripatric speciation events were identified along with one case of allopatric speciation. Peripatric speciation is supported through uneven potential and realized distributions and uneven population size estimates based on field collections. An associated climate shift was observed in most potentially peripatric splits. Morphological variation was highest in sexually dimorphic traits such as body size and gular shape, but this variation was not limited to peripatric species pairs as hypothesized. The potentially allopatric species pair showed no niche shifts and equivalent effective population sizes, ruling out peripatry in that speciation event. Two major ecological niche shifts were recovered within this radiation, possibly as adaptations to occupy areas of grassland that became more prevalent in the last 5 million years. Restricted and fluctuating grassland mosaics within forests might promote peripatric speciation in the Eastern Arc Biodiversity Hotspot (EABH). In our case study, peripatric speciation appears to be an important driver

  13. Tracking channel bed resiliency in forested mountain catchments using high temporal resolution channel bed movement

    Science.gov (United States)

    Martin, Sarah E.; Conklin, Martha H.

    2018-01-01

    This study uses continuous-recording load cell pressure sensors in four, high-elevation (1500-1800 m), Sierra Nevada headwater streams to collect high-temporal-resolution, bedload-movement data for investigating the channel bed movement patterns within these streams for water years 2012-2014. Data show an annual pattern where channel bed material in the thalweg starts to build up in early fall, peaks around peak snow melt, and scours back to baseline levels during hydrograph drawdown and base flow. This pattern is punctuated by disturbance and recovery of channel bed material associated with short-term storm events. A conceptual model, linking sediment sources at the channel margins to patterns of channel bed fill and scour in the thalweg, is proposed building on the results of Martin et al. (2014). The material in the thalweg represents a balance between sediment supply from the channel margins and sporadic, conveyor-belt-like downstream transport in the thalweg. The conceptual model highlights not only the importance of production and transport rates but also that seasonal connectedness between the margins and thalweg is a key sediment control, determining the accumulation rate of sediment stores at the margins and the redistribution of sediment from margins to thalweg that feeds the conveyor belt. Disturbance and recovery cycles are observed at multiple temporal scales; but long term, the channel beds are stable, suggesting that the beds act as short-term storage for sediment but are in equilibrium interannually. The feasibility of use for these sensors in forested mountain stream environments is tested. Despite a high failure rate (50%), load cell pressure sensors show potential for high-temporal-resolution bedload measurements, allowing for the collection of channel bed movement data to move beyond time-integrated change measurements - where many of the subtleties of bedload movement patterns may be missed - to continuous and/or real-time measurements. This

  14. Bed Bugs: The Australian Response

    Directory of Open Access Journals (Sweden)

    Richard C. Russell

    2011-04-01

    Full Text Available Australia has experienced a sudden and unexpected resurgence in bed bug infestations from both Cimex lectularius L. and Cimex hemipterus F. A survey in 2006 revealed that infestations had increased across the nation by an average of 4,500% since the start of the decade. In response, a multi-disciplinary approach to combat the rise of this public health pest was implemented and involved the coordinated efforts of several organizations. The key components of the strategy included the introduction of a pest management standard ‘A Code of Practice for the Control of Bed Bug Infestations in Australia’ that defines and promotes ‘best practice’ in bed bug eradication, the development of a policy and procedural guide for accommodation providers, education of stakeholders in best management practices, and research. These strategies continue to evolve with developments that lead to improvements in ‘best practice’ while bed bugs remain problematic in Australia.

  15. Getting Rid of Bed Bugs

    Science.gov (United States)

    ... control is very important whether you are considering hiring a professional or planning to do it yourself. Controlling bed ... control methods, as others may cause serious harm. Hiring a pest management professional is a good option in many cases, but ...

  16. Sea bed mapping and inspection

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2006-07-01

    The conference has 24 presentations on the topics: Sea bed mapping, inspection, positioning, hydrography, marine archaeology, remote operation vehicles and computerized simulation technologies, oil field activities and plans, technological experiences and problems. (tk)

  17. Moisture diffusivity in structure of random fractal fiber bed

    Energy Technology Data Exchange (ETDEWEB)

    Zhu, Fanglong, E-mail: zhufanglong_168@163.com [College of Textile, Zhongyuan University of Technology, Zhengzhou City (China); The Chinese People' s Armed Police Forces Academy, Langfan City (China); Zhou, Yu; Feng, Qianqian [College of Textile, Zhongyuan University of Technology, Zhengzhou City (China); Xia, Dehong [School of Mechanical Engineering, University of Science and Technology, Beijing (China)

    2013-11-08

    A theoretical expression related to effective moisture diffusivity to random fiber bed is derived by using fractal theory and considering both parallel and perpendicular channels to diffusion flow direction. In this Letter, macroporous structure of hydrophobic nonwoven material is investigated, and Knudsen diffusion and surface diffusion are neglected. The effective moisture diffusivity predicted by the present fractal model are compared with water vapor transfer rate (WVTR) experiment data and calculated values obtained from other theoretical models. This verifies the validity of the present fractal diffusivity of fibrous structural beds.

  18. Thermal-hydraulic considerations for particle bed reactors

    Science.gov (United States)

    Benenati, R.; Araj, K. J.; Horn, F.

    In the design of particle bed reactor (PBR) cores, consideration must be given to the gas coolant channels and their configuration. Neutronics analysis provides the relative volume fractions of the component materials, but these must be arranged in such a manner as to allow proper cooling of all components by the gas flow at relatively low pressure drops. The thermal hydraulic aspects of this problem are addressed. A description of the computer model used in the analysis of the steady state condition is also included. Blowdown tests on hot particle bed fuel elements were carried out and are described.

  19. Numerical modeling of straw combustion in a fixed bed

    DEFF Research Database (Denmark)

    Zhou, Haosheng; Jensen, Anker; Glarborg, Peter

    2005-01-01

    are in good agreement with measurements at different operating conditions such as primary air-flow rate, pre-heating of the primary air, oxygen concentration, moisture content in straw, and bulk density of the straw in the fixed bed. A parametric study indicates that the effective heat conductivity, straw......Straw is being used as main renewable energy source in grate boilers in Denmark. For optimizing operating conditions and design parameters, a one-dimensional unsteady heterogeneous mathematical model has been developed and experiments have been carried out for straw combustion in a fixed bed...

  20. Moisture diffusivity in structure of random fractal fiber bed

    International Nuclear Information System (INIS)

    Zhu, Fanglong; Zhou, Yu; Feng, Qianqian; Xia, Dehong

    2013-01-01

    A theoretical expression related to effective moisture diffusivity to random fiber bed is derived by using fractal theory and considering both parallel and perpendicular channels to diffusion flow direction. In this Letter, macroporous structure of hydrophobic nonwoven material is investigated, and Knudsen diffusion and surface diffusion are neglected. The effective moisture diffusivity predicted by the present fractal model are compared with water vapor transfer rate (WVTR) experiment data and calculated values obtained from other theoretical models. This verifies the validity of the present fractal diffusivity of fibrous structural beds.