WorldWideScience

Sample records for flow experiments 4th

  1. Mercury flow experiments. 4th report: Measurements of erosion rate caused by mercury flow

    International Nuclear Information System (INIS)

    Kinoshita, Hidetaka; Kaminaga, Masanori; Haga, Katsuhiro; Hino, Ryutaro

    2002-06-01

    The Japan Atomic Energy Research Institute (JAERI) and the High Energy Accelerator Research Organization (KEK) are promoting a construction plan of the Material-Life Science Facility, which is consisted of a Muon Science Facility and a Neutron Scattering Facility, in order to open up the new science fields. The Neutron Scattering Facility will be utilized for advanced fields of Material and Life science using high intensity neutron generated by the spallation reaction of a 1 MW pulsed proton beam and mercury target. Design of the spallation mercury target system aims to obtain high neutron performance with high reliability and safety. Since the target system is using mercury as the target material and contains large amount of radioactive spallation products, it is necessary to estimate reliability for strength of instruments in a mercury flow system during lifetime of the facility. Piping and components in the mercury flow system would be damaged by erosion with mercury flow, since these components will be weak by thickness decreasing. This report presents experimental results of wall thickness change by erosion using a mercury experimental loop. In the experiments, an erosion test section and coupons were installed in the mercury experimental loop, and their wall thickness was measured with an ultra sonic thickness gage after every 1000 hours. As a result, under 0.7 m/s of mercury velocity condition which is slightly higher than the practical velocity in mercury pipelines, the erosion is about 3 μm in 1000 hours. The wall thickness decrease during facility lifetime of 30 years is estimated to be less than 0.5 mm. According to the experimental result, it is confirmed that the effect of erosion on component strength is extremely small. Moreover, a measurement of residual mercury on the piping surface was carried out. As a result, 19 g/m 2 was obtained as the residual mercury for the piping surface. According to this result, estimated amount of residual mercury for

  2. Mercury flow experiments. 4th report Measurements of erosion rate caused by mercury flow

    CERN Document Server

    Kinoshita, H; Hino, R; Kaminaga, M

    2002-01-01

    The Japan Atomic Energy Research Institute (JAERI) and the High Energy Accelerator Research Organization (KEK) are promoting a construction plan of the Material-Life Science Facility, which is consisted of a Muon Science Facility and a Neutron Scattering Facility, in order to open up the new science fields. The Neutron Scattering Facility will be utilized for advanced fields of Material and Life science using high intensity neutron generated by the spallation reaction of a 1 MW pulsed proton beam and mercury target. Design of the spallation mercury target system aims to obtain high neutron performance with high reliability and safety. Since the target system is using mercury as the target material and contains large amount of radioactive spallation products, it is necessary to estimate reliability for strength of instruments in a mercury flow system during lifetime of the facility. Piping and components in the mercury flow system would be damaged by erosion with mercury flow, since these components will be we...

  3. 4th micro and nano flows conference (book of abstracts)

    OpenAIRE

    König, CS; Karayiannis, TG; Balabani, S; 4th Micro and Nano Flows Conference (MNF2014)

    2014-01-01

    This paper was presented at the 4th Micro and Nano Flows Conference (MNF2014), which was held at University College, London, UK. The conference was organised by Brunel University and supported by the Italian Union of Thermofluiddynamics, IPEM, the Process Intensification Network, the Institution of Mechanical Engineers, the Heat Transfer Society, HEXAG - the Heat Exchange Action Group, and the Energy Institute, ASME Press, LCN London Centre for Nanotechnology, UCL University College London, U...

  4. Trialling a 4th Generation Approach to the First Year Experience: The CommUniTI

    Directory of Open Access Journals (Sweden)

    Sharn Donnison

    2017-03-01

    Full Text Available In 2014, we developed a new approach to supporting first year students’ transition into higher education building on the work of Kift, Nelson, and Clarke (2010 whose 3rd Generation Approach is one of transition pedagogy foregrounded by a whole-of-institution transformation. Our 4th Generation Approach focuses on students’ social capital and extends the remit beyond the institution. Our approach recognises students’ social capital as an unexplored resource to be drawn upon to inform the membership of a Community of Practice (CoP. The CoP members collaboratively develop strategies to support the development of students’ important cultural capital, which we consider essential for successful transition. In 2015, we trialled the 4th Generation Approach with a Queensland regional university satellite campus. This paper reports on the implementation of the CoP as one element of the 4th Generation Approach and the important refinements required for future success.

  5. Calibration of a low background gas-flow proportional counter to estimate "2"3"4Th activity in coastal waters

    International Nuclear Information System (INIS)

    Cuesta, E.; Lozano, R.L.; Miguel, E.G. San; Casas-Ruiz, M.; Bolívar, J.P.

    2016-01-01

    This paper relates the calibration of a low background gas-flow proportional counter. This calibration has been used to determine low activity of "2"3"4Th in coastal water samples. Two methods were used to prepare calibration samples: Evaporation and Electrodeposition. First method was rejected due to the lack of reproducibility because the different geometry adopted by the drops of tracer once dried on the disk. On the contrary, through the second method, similar efficiencies were obtained in all detectors with an average of 0.401±0.004. In this paper, the whole procedure to obtain "2"3"4Th activity in dissolution as well as in particulate matter has been detailed, and all the algorithms needed to calculate activities and efficiencies are shown. Finally, two experiments have been designed in order to validate the calibration of the beta counter and the method to determine "2"3"4Th in coastal waters with high concentration of particulate matter. - Highlights: • This paper shows a Home-made calibration using two methods to prepare calibration samples. • The algorithms needed to obtain Th-234 activity concentrations are described in full detail. • This is the first time Th-234 has been determined in water samples from Huelva Estuary.

  6. ECMOR 4. 4th European conference on the mathematics of oil recovery. Topic D: Simulation of fluid flow. Proceedings

    Energy Technology Data Exchange (ETDEWEB)

    1994-01-01

    The report with collected proceedings from a conference, deals with mathematics of oil recovery with the focus on simulation of fluid flow. Topics of proceedings are as follow: Validity of macroscopic viscous fingering models for 2D and 3D-flows; pressure equation for fluid flow in a stochastic medium; predicting multicomponent, multiphase flow in heterogeneous systems using streamtubes; analytic techniques in pressure transient testing; global triangular structure in four-component conservation laws; exact solution of the problem on hydrodynamic interaction between noncommunicating layers under conditions of their joint development; fluid rate in flowing granular medium with moving boundary; complex variable boundary element method for tracking streamlines across fractures; transport equations for miscible displacements in heterogeneous porous media - a streamtube approach; mathematical modelling of condensate film flow by gravity drainage; effect of capillary forces on immiscible two-phase flow in strongly heterogeneous porous media; multidomain direct method and local time steps in reservoir simulation; adaptive methods for chemical flooding; flux continuous for the full tensor equation; discretization on non-orthogonal, curvilinear grids for multi-phase flow; blending finite elements and finite volumes for the solution of miscible incompressible flow. 16 papers are prepared. 240 refs., 122 figs., 6 tabs.

  7. Reforming the 4th-Year Curriculum as a Springboard to Graduate Medical Training: One School's Experiences and Lessons Learned.

    Science.gov (United States)

    Wackett, Andrew; Daroowalla, Feroza; Lu, Wei-Hsin; Chandran, Latha

    2016-01-01

    Concerns regarding the quality of training in the 4th year of medical school and preparation of graduates to enter residency education persist and are borne out in the literature. We reviewed the published literature regarding Year 4 concerns as well as institutional efforts to improve the 4th-year curriculum from several schools. Based on input from key stakeholders, we established 4 goals for our Year 4 curriculum reform: (a) standardize the curricular structure, (b) allow flexibility and individualization, (c) improve the preparation for residency, and (d) improve student satisfaction. After the reform, we evaluated the outcomes using results from the Association of American Medical Colleges Questionnaire, student focus groups, and program director surveys. This article describes the context, process, and outcomes of the reform of the Year 4 curriculum at Stony Brook University School of Medicine. We were able to achieve all four stated goals for the reform. The significant components of the change included a flexible adaptable curriculum based on individual needs and preferences, standardized learning objectives across the year, standardized competency-based evaluations regardless of discipline, reinforcement of clinical skills, and training for the transition to the workplace as an intern. The reform resulted in increased student satisfaction, increased elective time, and increased preparedness for residency training as perceived by the graduates. The Program Director survey showed significant changes in ability to perform a medical history and exam, management of common medical conditions and emergencies, clinical reasoning and problem-solving skills, working and communication with the healthcare team, and overall professionalism in meeting obligations inherent in the practice of medicine. Lessons learned from our 4th-year reform process are discussed. Listening to the needs of the stakeholders was an important step in ensuring buy-in, having an institutional

  8. Symposium on Turbulent Shear Flows (4th) Held at Karlsruhe University (Germany, F.R.), 12-14 September 1983.

    Science.gov (United States)

    1983-09-01

    investigations in ducts of constant surfaces to a rectangle (40a0 lx60+0 1mm) at the exit cross-sectional area (Humphrey et al. 1977. 1981. Enayet at after 45...k___ to the thinner inlet boundary layers. Enayet et a1(1982) (1982a). The C-shaped diffuser was assembled with the measured the developing flow in a...about 0 25 Vb measured at the 450 smaller radial velocities In the turbulent case (cf plane of the constant area duct of Enayet et al (1982) of figures

  9. Irradiation experiments of 3rd, 4th and 5th fuel assemblies by an in-pile gas loop, OGL-1

    International Nuclear Information System (INIS)

    Fukuda, Kousaku; Kobayashi, Fumiaki; Hayashi, Kimio; Minato, Kazuo; Kikuchi, Teruo; Adachi, Mamoru; Iwamoto, Kazumi; Ikawa, Katsuichi; Itami, Hiroharu.

    1986-07-01

    Three irradiation experiments for 3rd, 4th and 5th fuel assemblies which had been composed of VHTR reference coated particle fuels and graphite components were carried out by an in-pile gas loop, OGL-1 during 1979 and 1982. The main purposes of these experiments were to study on bowing of the fuel rod by irradiation for the 3rd fuel assembly, to study on fuel behavior under relatively low burnup irradiation for the 4th fuel assembly, and to study on fuel behavior up to full burnup of VHTR design for the 5th fuel assembly. For understanding in-pile fuel behavior, fractional releases of fission gases from each fuel assembly were estimated by measuring the fission gas concentrations in the primary loop of OGL-1. The post-irradiation examination (PIE) was carried out extensively on the fuel block, the fuel rods and the fuel compacts in Tokai Hot Laboratory. Also, made were the measurements of metallic fission product distributions in the fuel assemblies and the fuel rods. The results in these experiments were given as follows ; bowing of the fuel rod in the 3rd fuel assembly was 0.7 mm, but integrity of the rod was kept under irradiation. Fractional release of the fission gas from the 4th fuel assembly remained in the order of 10 -7 during irradiation, suggesting that the fuel performance was excellent. The fractional release from the 5th fuel assembly, on the other hand, was in the order of 10 -5 which was the same level in the VHTR design. (author)

  10. The not-so-sterile 4th neutrino: constraints on new gauge interactions from neutrino oscillation experiments

    Science.gov (United States)

    Kopp, Joachim; Welter, Johannes

    2014-12-01

    Sterile neutrino models with new gauge interactions in the sterile sector are phenomenologically interesting since they can lead to novel effects in neutrino oscillation experiments, in cosmology and in dark matter detectors, possibly even explaining some of the observed anomalies in these experiments. Here, we use data from neutrino oscillation experiments, in particular from MiniBooNE, MINOS and solar neutrino experiments, to constrain such models. We focus in particular on the case where the sterile sector gauge boson A ' couples also to Standard Model particles (for instance to the baryon number current) and thus induces a large Mikheyev-Smirnov-Wolfenstein potential. For eV-scale sterile neutrinos, we obtain strong constraints especially from MINOS, which restricts the strength of the new interaction to be less than ˜ 10 times that of the Standard Model weak interaction unless active-sterile neutrino mixing is very small (sin2 θ 24 ≲ 10-3). This rules out gauge forces large enough to affect short-baseline experiments like MiniBooNE and it imposes nontrivial constraints on signals from sterile neutrino scattering in dark matter experiments.

  11. Report on the 4th International Conference on monitoring, simulation, prevention and remediation of dense and debris flows - Debris Flow 2012

    Directory of Open Access Journals (Sweden)

    Daniele de Wrachien

    2012-09-01

    Full Text Available Debris and hyper-concentrated flows are amongst the most destructive of all water-related disasters. These hazards are likely to become more frequent and more important in the future due to the effects of the increase in population, urbanization, land subsidence and the impact of climate change. They affect both rural and urban environments, particularly in river basins and in mountain areas. In recent years, they have attracted more and more attention from the scientific and professional communities due to the number of lives lost, and there is growing public concern for the future. New methods and measures are required to cope with debris flow changes and to achieve a harmonious balance between the environment and economic forces.

  12. The 4th Thermodynamic Principle?

    International Nuclear Information System (INIS)

    Montero Garcia, Jose de la Luz; Novoa Blanco, Jesus Francisco

    2007-01-01

    It should be emphasized that the 4th Principle above formulated is a thermodynamic principle and, at the same time, is mechanical-quantum and relativist, as it should inevitably be and its absence has been one of main the theoretical limitations of the physical theory until today.We show that the theoretical discovery of Dimensional Primitive Octet of Matter, the 4th Thermodynamic Principle, the Quantum Hexet of Matter, the Global Hexagonal Subsystem of Fundamental Constants of Energy and the Measurement or Connected Global Scale or Universal Existential Interval of the Matter is that it is possible to be arrived at a global formulation of the four 'forces' or fundamental interactions of nature. The Einstein's golden dream is possible

  13. 4th Machining Innovations Conference

    CERN Document Server

    2014-01-01

    This contributed volume contains the research results presented at the 4th Machining Innovations Conference, Hannover, September 2013. The topic of the conference are new production technologies in aerospace industry and the focus is on energy efficient machine tools as well as sustainable process planning. The target audience primarily comprises researchers and experts in the field but the book may also be beneficial for graduate students.

  14. Experience-based teaching of acute medicine for extra motivated medical students and young physicians – 4th Emergency Medicine Course and 6th AKUTNĚ.CZ Congress

    Directory of Open Access Journals (Sweden)

    Petr Štourač

    2014-12-01

    Full Text Available Faculty of Medicine of the Masaryk University (MU, and especially its departments focusing on acute medicine, make an active effort to find and to support extra motivated students by organising courses and congresses with simulation-based learning sessions for them. 4th Emergency Medicine Course (EMC and 6th AKUTNĚ.CZ Congress were organised during 2014. EMC was held during a weekend in mid-April for 80 medical students. The congress was held on 22nd November 2014. A group of more than 700 enthusiastic professionals including physicians, nursing staff and medical students interested in acute medicine met again in Brno at the University Campus Bohunice. We also report the evaluation of effectiveness of different types of sessions, as well as its influence on practical skills and the fixation of memory footprint. The website AKUTNĚ.CZ (www.akutne.cz is freely accessible, and anyone can find and watch all the videos and presentations there.

  15. 4th International Cryocoolers Conference

    CERN Document Server

    Patton, George; Knox, Margaret

    1987-01-01

    The Cryocoolers 4 proceedings archives the contributions of leading international experts at the 4th International Cryocooler Conference that was held in Easton, Maryland on September 25-26, 1986. About 170 people attended the conference representing 11 countries, 14 universities, 21 government laboratories and 60 industrial companies. Thirty-one papers were presented describing advancements and applications of cryocoolers in the temperature range below 80K. This year's conference was sponsored by the David Taylor Naval Ship Research and Development Center of Annapolis, Maryland, and the conference proceedings reproduced here was published by them.

  16. Water Flow Experiments

    Indian Academy of Sciences (India)

    year undergraduate student at Ashoka University,. Sonipat, Haryana. This article studies how the height of water varies with time when water ... Experiment using a one-bottle system with a small bore tube at- tached to .... restricting free flow.

  17. The Leap into 4th Grade

    Science.gov (United States)

    Anderson, Mike

    2011-01-01

    Fourth grade is a pivotal year, in which students commonly face increased academic demands. According to Anderson, teachers can help students make a smooth transition to 4th grade by introducing these new challenges in ways that are in line with 4th graders' common developmental characteristics: incredible energy and emotion, industriousness and…

  18. 4th European Turbulence Conference

    CERN Document Server

    1993-01-01

    The European Turbulence Conferences have been organized under the auspices of the European Mechanics Committee (Euromech) to provide a forum for discussion and exchange of recent and new results in the field of turbulence. The first conference was organized in Lyon in 1986 with 152 participants. The second and third conferences were held in Berlin (1988) and Stockholm (1990) with 165 and 172 participants respectively. The fourth was organized in Delft from 30 June to 3 July 1992 by the J.M. Burgers Centre. There were 214 participants from 22 countries. This steadily growing number of participants demonstrates both the success and need for this type of conference. The main topics of the Fourth European Turbulence Conference were: Dynamical Systems and Transition; Statistical Physics and Turbulence; Experiments and Novel Experimental Techniques; Particles and Bubbles in Turbulence; Simulation Methods; Coherent Structures; Turbulence Modelling and Compressibility Effects. In addition a special session was held o...

  19. 4th generation light source instrumentation

    International Nuclear Information System (INIS)

    Lumpkin, A.

    1998-01-01

    This working group on 4th Generation Light Source (4GLS) Instrumentation was a follow-up to the opening-discussion on Challenges in Beam Profiling. It was in parallel with the Feedback Systems session. We filled the SSRL Conference Room with about 25 participants. The session opened with an introduction by Lumpkin. The target beam parameter values for a few-angstrom, self-amplified spontaneous emissions (SASE) experiment and for a diffraction-limited soft x-ray storage ring source were addressed. Instrument resolution would of course need to be 2-3 times better than the value measured, if possible. The nominal targeted performance parameters are emittance (1-2π mm mrad), bunch length (100 fs), peak-current (l-5 kA), beam size (10 microm), beam divergence (1 microrad), energy spread (2 x 10 -4 ), and beam energy (10's of GeV). These are mostly the SASE values, and the possible parameters for a diffraction-limited soft x-ray source would be relaxed somewhat. Beam stability and alignment specifications in the sub-micron domain for either device are anticipated

  20. Hopper Flow: Experiments and Simulation

    Science.gov (United States)

    Li, Zhusong; Shattuck, Mark

    2013-03-01

    Jamming and intermittent granular flow are important problems in industry, and the vertical hopper is a canonical example. Clogging of granular hoppers account for significant losses across many industries. We use realistic DEM simulations of gravity driven flow in a hopper to examine flow and jamming of 2D disks and compare with identical companion experiments. We use experimental data to validate simulation parameters and the form of the inter particle force law. We measure and compare flow rate, emptying times, jamming statistics, and flow fields as a function of opening angle and opening size in both experiment and simulations. Suppored by: NSF-CBET-0968013

  1. 4th Generation District Heating (4GDH)

    DEFF Research Database (Denmark)

    Lund, Henrik; Werner, Sven; Wiltshire, Robin

    2014-01-01

    This paper defines the concept of 4th Generation District Heating (4GDH) including the relations to District Cooling and the concepts of smart energy and smart thermal grids. The motive is to identify the future challenges of reaching a future renewable non-fossil heat supply as part...... of the implementation of overall sustainable energy systems. The basic assumption is that district heating and cooling has an important role to play in future sustainable energy systems – including 100 percent renewable energy systems – but the present generation of district heating and cooling technologies will have...

  2. 4th Pacific Rim Underwater Acoustics Conference

    CERN Document Server

    Xu, Wen; Cheng, Qianliu; Zhao, Hangfang

    2016-01-01

    These proceedings are a collection of 16 selected scientific papers and reviews by distinguished international experts that were presented at the 4th Pacific Rim Underwater Acoustics Conference (PRUAC), held in Hangzhou, China in October 2013. The topics discussed at the conference include internal wave observation and prediction; environmental uncertainty and coupling to sound propagation; environmental noise and ocean dynamics; dynamic modeling in acoustic fields; acoustic tomography and ocean parameter estimation; time reversal and matched field processing; underwater acoustic localization and communication as well as measurement instrumentations and platforms. These proceedings provide insights into the latest developments in underwater acoustics, promoting the exchange of ideas for the benefit of future research.

  3. Lunar heat-flow experiment

    Science.gov (United States)

    Langseth, M. G.

    1977-01-01

    The principal components of the experiment were probes, each with twelve thermometers of exceptional accuracy and stability, that recorded temperature variations at the surface and in the regolith down to 2.5 m. The Apollo 15 experiment and the Apollo 17 probes recorded lunar surface and subsurface temperatures. These data provided a unique and valuable history of the interaction of solar energy with lunar surface and the effects of heat flowing from the deep interior out through the surface of the moon. The interpretation of these data resulted in a clearer definition of the thermal and mechanical properties of the upper two meters of lunar regolith, direct measurements of the gradient in mean temperature due to heat flow from the interior and a determination of the heat flow at the Apollo 15 and Apollo 17 sites.

  4. 4th international interdisciplinary chaos symposium

    CERN Document Server

    Banerjee, Santo; Caglar, Suleyman; Ozer, Mehmet; Chaos and complex systems

    2013-01-01

    Complexity Science and Chaos Theory are fascinating areas of scientific research with wide-ranging applications.  The interdisciplinary nature and ubiquity of complexity and chaos are features that provides scientists with a motivation to pursue general theoretical tools and frameworks. Complex systems give rise to emergent behaviors, which in turn produce novel and interesting phenomena in science, engineering, as well as in the socio-economic sciences. The aim of all Symposia on Chaos and Complex Systems (CCS) is to bring together scientists, engineers, economists and social scientists, and to discuss the latest insights and results obtained in the area of corresponding nonlinear-system complex (chaotic) behavior. Especially for the “4th International Interdisciplinary Chaos Symposium on Chaos and Complex Systems,” which took place April 29th to May 2nd, 2012 in Antalya, Turkey, the scope of the symposium had been further enlarged so as to encompass the presentation of work from circuits to econophysic...

  5. 4th World Conference on Soft Computing

    CERN Document Server

    Abbasov, Ali; Yager, Ronald; Shahbazova, Shahnaz; Reformat, Marek

    2016-01-01

    This book reports on advanced theories and cutting-edge applications in the field of soft computing. The individual chapters, written by leading researchers, are based on contributions presented during the 4th World Conference on Soft Computing, held May 25-27, 2014, in Berkeley. The book covers a wealth of key topics in soft computing, focusing on both fundamental aspects and applications. The former include fuzzy mathematics, type-2 fuzzy sets, evolutionary-based optimization, aggregation and neural networks, while the latter include soft computing in data analysis, image processing, decision-making, classification, series prediction, economics, control, and modeling. By providing readers with a timely, authoritative view on the field, and by discussing thought-provoking developments and challenges, the book will foster new research directions in the diverse areas of soft computing. .

  6. 4th Conference on Microactuators and Micromechanisms

    CERN Document Server

    Corves, Burkhard; Jensen, Brian; Lovasz, Erwin-Christian

    2017-01-01

    This book brings together investigations which combine theoretical and experimental results related to such systems as capsule micromechanisms, active micro catheters, nanotube vascular stents, mechanisms for micromilling, different compliant mechanisms including grippers and compliant systems with actuators and sensors, microrobots based on vibrations, tactile sensors, tooth brackets, compliant valves, and space reflectors. This volume contains twenty-two contributions from researchers from ten countries, represented at the 4th Conference on Microactuators and Micromechanisms, which was held in 2016 in Ilmenau, Germany. The aim of the conference was to provide a special opportunity for a know-how exchange and collaboration in various disciplines concerning systems pertaining to micro-technology. This Conference was organized under the patronage of IFToMM (International Federation for the Promotion of Mechanism and Machine Science). .

  7. 4th International Conference Nanotechnology and Nanomaterials

    CERN Document Server

    Yatsenko, Leonid

    2017-01-01

    This book presents some of the latest achievements in nanotechnology and nanomaterials from leading researchers in Ukraine, Europe, and beyond. It features contributions from participants in the 4th International Science and Practice Conference Nanotechnology and Nanomaterials (NANO2016) held in Lviv, Ukraine on August 24-27, 2016. The International Conference was organized jointly by the Institute of Physics of the National Academy of Sciences of Ukraine, Ivan Franko National University of Lviv (Ukraine), University of Tartu (Estonia), University of Turin (Italy), and Pierre and Marie Curie University (France). Internationally recognized experts from a wide range of universities and research institutions share their knowledge and key results on topics ranging from nanooptics, nanoplasmonics, and interface studies to energy storage and biomedical applications. Presents cutting-edge advances in nanocomposites and carbon and silicon-based nanomaterials for a wide range of engineering and medical applications Co...

  8. European Code against Cancer 4th Edition

    DEFF Research Database (Denmark)

    Friis, Søren; Kesminiene, Ausrele; Espina, Carolina

    2015-01-01

    were given for carcinogenic drugs and medical radiation in the 4th edition of European Code against Cancer. It is crucial that the application of these measures relies on medical expertise and thorough benefit-risk evaluation. This also pertains to cancer-preventive drugs, and self...... of treatment, and initiation according to the time of menopause. Carcinogenicity has also been established for anti-neoplastic agents used in cancer therapy, immunosuppressants, oestrogen-progestogen contraceptives, and tamoxifen. Medical use of ionising radiation, an established carcinogen, can provide major...... health benefits; however, prudent practices need to be in place, with procedures and techniques providing the needed diagnostic information or therapeutic gain with the lowest possible radiation exposure. For pharmaceutical drugs and medical radiation exposure with convincing evidence...

  9. 4th International Conference on Power Transmissions

    CERN Document Server

    2013-01-01

    This books contains the Proceedings of the 4th International Conference on Power Transmissions, that was held in Sinaia, Romania from June 20 -23, 2012. Power Transmissions is a very complex and multi-disciplinary scientific field of Mechanical Engineering that covers the different types of transmissions (mechanical, hydraulic, pneumatic) as well as all the machine elements involved, such as gears, bearings, shafts, couplings and a lot more. It concerns not only their basic theory but also their design, analysis, testing, application and maintenance. The requirements set to modern power transmissions are really tough to meet: They need to be more efficient, stronger, smaller, noiseless, easier to produce and to cost less. There is a strong demand to become easier in operation and maintenance, or even automatic and in maintenance-free. Last but not least, they should be easily recycled and respect the environment. Joint efforts of specialists from both academia and industry can significantly contribute to fulf...

  10. Magendie and Luschka: Holes in the 4th ventricle

    Directory of Open Access Journals (Sweden)

    Eliasz Engelhardt

    Full Text Available ABSTRACT Cerebrospinal fluid (CSF is a complex liquid formed mainly by the choroid plexuses. After filling the ventricular system where it circulates, CSF flows out to the subarachnoid spaces through openings in the 4th ventricle. Following numerous studies on CSF pathways, these openings were first discovered in the 19th century by two notable researchers, François Magendie and Hubert von Luschka, who described the median and lateral openings subsequently named after them. Even after the studies of Axel Key and Gustav Magnus Retzius confirming these openings, their existence was questioned by many anatomists, yet acknowledged by others. Finally gaining the acceptance of all, recognition of the holes endures to the present day. Interest in these openings may be attributed to the several congenital or acquired pathological conditions that may affect them, usually associated with hydrocephalus. We report some historical aspects of these apertures and their discoverers.

  11. 4th International Conference in Software Engineering for Defence Applications

    CERN Document Server

    Sillitti, Alberto; Succi, Giancarlo; Messina, Angelo

    2016-01-01

    This book presents high-quality original contributions on new software engineering models, approaches, methods, and tools and their evaluation in the context of defence and security applications. In addition, important business and economic aspects are discussed, with a particular focus on cost/benefit analysis, new business models, organizational evolution, and business intelligence systems. The contents are based on presentations delivered at SEDA 2015, the 4th International Conference in Software Engineering for Defence Applications, which was held in Rome, Italy, in May 2015. This conference series represents a targeted response to the growing need for research that reports and debates the practical implications of software engineering within the defence environment and also for software performance evaluation in real settings through controlled experiments as well as case and field studies. The book will appeal to all with an interest in modeling, managing, and implementing defence-related software devel...

  12. 4th International Conference on Applied Computing and Information Technology

    CERN Document Server

    2017-01-01

    This edited book presents scientific results of the 4th International Conference on Applied Computing and Information Technology (ACIT 2016) which was held on December 12–14, 2016 in Las Vegas, USA. The aim of this conference was to bring together researchers and scientists, businessmen and entrepreneurs, teachers, engineers, computer users, and students to discuss the numerous fields of computer science and to share their experiences and exchange new ideas and information in a meaningful way. The aim of this conference was also to bring out the research results about all aspects (theory, applications and tools) of computer and information science, and to discuss the practical challenges encountered along the way and the solutions adopted to solve them. The conference organizers selected the best papers from those papers accepted for presentation at the conference. The papers were chosen based on review scores submitted by members of the Program Committee, and underwent further rigorous rounds of review. Th...

  13. 4th Workshop on Combinations of Intelligent Methods and Applications

    CERN Document Server

    Palade, Vasile; Prentzas, Jim

    2016-01-01

    This volume includes extended and revised versions of the papers presented at the 4th Workshop on “Combinations of Intelligent Methods and Applications” (CIMA 2014) which was intended to become a forum for exchanging experience and ideas among researchers and practitioners dealing with combinations of different intelligent methods in Artificial Intelligence. The aim is to create integrated or hybrid methods that benefit from each of their components. Some of the existing presented efforts combine soft computing methods (fuzzy logic, neural networks and genetic algorithms). Another stream of efforts integrates case-based reasoning or machine learning with soft-computing methods. Some of the combinations have been more widely explored, like neuro-symbolic methods, neuro-fuzzy methods and methods combining rule-based and case-based reasoning. CIMA 2014 was held in conjunction with the 26th IEEE International Conference on Tools with Artificial Intelligence (ICTAI 2014). .

  14. Differential diagnosis of the 4th ventricular tumors

    International Nuclear Information System (INIS)

    Lee, Sang Woo; Lee, Jong Min; Kang, Moo Song; Kim, Chul Min; Kim, Chang Soo

    1997-01-01

    To determine by analysis of MR and CT findings the points of differentiation among 4th ventricular tumors, especially the change of shape of the 4th ventricle caused by the site at which 4th ventricular tumors originate. The authors retrospectively analyzed and compared the CT(n=5) and MRI(n=12) findings of 13 pathologically proven 4th ventricular tumors comprising six medulloblastomas three ependymomas(4 cases) and three choroids plexus papillomas. On axial MRI medulloblastomas showed anterior and anterolateral CSF-clefts between the tumor mass and the 4th ventricular wall in one and five cases, respectively; on sagittal MRI, anterior beaking of the upper 4th ventricle was seen. Two ependymomas showed posterolateral CSF-cleft on axial MRI and posterior beaking of the upper 4th ventricle on sagittal MRI. Two ependymomas and all choroids plexus papillomas showed anterior, posterior and lateral CSF-clefts on axial MRI, and anterior and posterior beakings of the upper 4th ventricle on sagittal MRI. On Gd-DTPA enhanced T1WI, all medulloblastomas and ependymomas showed inhomogeneous enhancement, and all choroids plexus papillomas showed homogeneous enhancement. On CT, tow choroids plexus papillomas showed dense calcifications. The differential diagnosis of 4th ventricular tumors can be preoperatively suggested by analysis of findings such as a CSF-cleft between the tumor mass and the 4th ventricular wall on axial MR and CT images, the shape of the upper 4th ventricle on sagittal MRI, contrast enhancement pattern, necrosis and cyst, and CSF seeding

  15. Flow experiences in Shakuhachi teaching via Skype

    OpenAIRE

    How, Meng Leong

    2017-01-01

    This study examined how flow experiences contributed to the teaching practices of seven shakuhachi teachers from Australia, North America, Europe, and Japan, who were engaged in teaching their students via Skype. Findings in this study suggested that the shakuhachi teachers’ gravitas of teaching and the observed effortlessness in their practices of teaching students contributed to their experience of flow during teaching via Skype. An epi-flow conceptual model was engendered via a review ...

  16. Adubação do milho: XVIII - Ensaios com diversos fosfatos (4.ª série. Fertilizer experiments with corn: XVIII - Trials with various phosphorus sources (4th series

    Directory of Open Access Journals (Sweden)

    G.P Viégas

    1961-01-01

    Full Text Available Neste artigo os autores relatam os resultados de mais quatro ensaios de adubação do milho, realizados entre 1949-50 e 1956-57 em diferentes localidades do Estado de São Paulo, e nos quais superfosfato foi comparado com alguns fosfatos naturais, baseando-se o confronto nos seus teores totais de P2O5. Enquanto um dos ensaios foi anual, dois outros foram conduzidos por dois anos e, o quarto, por cinco anos. Em dois dêles também foi estudada a influência da adição de calcário. Tanto o calcário como os adubos só foram aplicados no primeiro ano. Em três ensaios super fosfato foi mui (o superior a Hiperfosfato e, sobretudo, a fosfato Serrote; no outro, os dois últimos fosfatos se mostraram equivalentes e foram apenas um pouco inferiores a super fosfato. Fosfato da Flórida, que só figurou em dois ensaios, comportou-se, em média, como Hiperfosfato. A superioridade de superfosfato proveio principalmente da sua maior eficiência no primeiro ano, pois a partir do segundo os efeitos residuais dos adubos estudados tenderam a se tornar iguais. No ensaio que durou cinco anos a resposta ao calcário foi pràticamente, nula nos dos primeiros anos, mas tornou-se apreciável nos seguintes. E.m outro, conduzido por dois anos em solo mais ácido, o efeito do corretivo foi sofrível no primeiro ano e muito bom no segundo. O calcário tendeu a beneficiar o efeito de superfosfato, mas influiu de modo contraditório sôbre o comportamento dos fosfatos naturais.In this fourth paper on phosphorus fertilizers for corn the authors report the results obtained in four experiments located on different sites of the State of São Paulo, in which superphosphate was compared with three ground rock phosphates, the comparison being based on their contents of total P2O5. While one experiment was annual, the others were conducted for two, two and five years. The effect of liming was also studied in two of the experiments. Lime and fertilizers were applied only in the

  17. 4th Penn State Bioinorganic Workshop

    Energy Technology Data Exchange (ETDEWEB)

    Krebs, Carsten [Pennsylvania State Univ., University Park, PA (United States)

    2017-08-22

    The research area of biological inorganic chemistry encompasses a wide variety of subfields, including molecular biology, biochemistry, biophysics, inorganic chemistry, analytical chemistry, physical chemistry, and theoretical chemistry, as well as many different methods, such as biochemical characterization of enzymes, reaction kinetics, a plethora of spectroscopic techniques, and computational methods. The above methods are combined to understand the formation, function, and regulation of the many metallo-cofactors found in Nature as well as to identify novel metallo-cofactors. Many metalloenzyme-catalyzed reactions are extremely complex, but are of fundamental importance to science and society. Examples include (i) the reduction of the chemically inert molecule, dinitrogen, to ammonia by the enzyme nitrogenase (this reaction is fundamental for the production of nitrogen fertilizers); (ii) the oxidation of water to dioxygen by the Mn4Ca cluster found in photosystem II; and (iii) myriad reactions in which aliphatic, inert C-H bonds are cleaved for subsequent functionalization of the carbon atoms (the latter reactions are important in the biosynthesis of many natural products). Because of the broad range of areas and techniques employed in this field, research in bioinorganic chemistry is typically carried out collaboratively between two or more research groups. It is of paramount importance that researchers working in this field have a good, basic, working knowledge of many methods and approaches employed in the field, in order to design and discuss experiments with collaborators. Therefore, the training of students working in bioinorganic chemistry is an important aspect of this field. Hugely successful “bioinorganic workshops” were offered in the 1990s at The University of Georgia. These workshops laid the foundation for many of the extant collaborative research efforts in this area today. The large and diverse group of bioinorganic chemists at The

  18. Building Bridges across Sectors and Scales: Exploring Systemic Solutions towards A Sustainable Management of Land —Experiences from 4th Year Status Conference on Research for Sustainable Land Management

    Directory of Open Access Journals (Sweden)

    Annegret Repp

    2015-04-01

    Full Text Available Interacting land use demands and competing interests originating from fields such as agriculture, housing, mobility and nature conservation call for integrated governance approaches that incorporate disciplinary perspectives and arbitrate between them. The German research program “Sustainable Land Management” targets this challenge and provides an umbrella for a number of regional projects involving transdisciplinary system-oriented approaches to sustainable land use, connecting researchers and practitioners. This research note gives an insight into the experiences presented at the program’s fourth year status conference, held in October 2014 in Berlin. It focuses on cross-scalar and cross-sectoral approaches to governing urban-rural interdependencies of land use and scrutinizes debates on how to implement and disseminate project results.

  19. Large-format, high-speed, X-ray pnCCDs combined with electron and ion imaging spectrometers in a multipurpose chamber for experiments at 4th generation light sources

    International Nuclear Information System (INIS)

    Strueder, Lothar; Epp, Sascha; Rolles, Daniel; Hartmann, Robert; Holl, Peter; Lutz, Gerhard; Soltau, Heike; Eckart, Rouven; Reich, Christian; Heinzinger, Klaus; Thamm, Christian; Rudenko, Artem; Krasniqi, Faton; Kuehnel, Kai-Uwe; Bauer, Christian; Schroeter, Claus-Dieter; Moshammer, Robert; Techert, Simone; Miessner, Danilo; Porro, Matteo

    2010-01-01

    Fourth generation accelerator-based light sources, such as VUV and X-ray Free Electron Lasers (FEL), deliver ultra-brilliant (∼10 12 -10 13 photons per bunch) coherent radiation in femtosecond (∼10-100 fs) pulses and, thus, require novel focal plane instrumentation in order to fully exploit their unique capabilities. As an additional challenge for detection devices, existing (FLASH, Hamburg) and future FELs (LCLS, Menlo Park; SCSS, Hyogo and the European XFEL, Hamburg) cover a broad range of photon energies from the EUV to the X-ray regime with significantly different bandwidths and pulse structures reaching up to MHz micro-bunch repetition rates. Moreover, hundreds up to trillions of fragment particles, ions, electrons or scattered photons can emerge when a single light flash impinges on matter with intensities up to 10 22 W/cm 2 . In order to meet these challenges, the Max Planck Advanced Study Group (ASG) within the Center for Free Electron Laser Science (CFEL) has designed the CFEL-ASG MultiPurpose (CAMP) chamber. It is equipped with specially developed photon and charged particle detection devices dedicated to cover large solid-angles. A variety of different targets are supported, such as atomic, (aligned) molecular and cluster jets, particle injectors for bio-samples or fixed target arrangements. CAMP houses 4π solid-angle ion and electron momentum imaging spectrometers ('reaction microscope', REMI, or 'velocity map imaging', VMI) in a unique combination with novel, large-area, broadband (50 eV-25 keV), high-dynamic-range, single-photon-counting and imaging X-ray detectors based on the pnCCDs. This instrumentation allows a new class of coherent diffraction experiments in which both electron and ion emission from the target may be simultaneously monitored. This permits the investigation of dynamic processes in this new regime of ultra-intense, high-energy radiation-matter interaction. After an introduction into the salient features of the CAMP chamber and

  20. Assessment of an Engineering Technology Outreach Program for 4th-7th Grade Girls

    Science.gov (United States)

    Dell, Elizabeth M.; Christman, Jeanne; Garrick, Robert D.

    2011-01-01

    This paper describes a workshop led by female Engineering Technology students, with support from female faculty, to provide an introduction to Engineering Technology to 4th-7th grade girls through a series of interactive laboratory experiments. This outreach program was developed to improve attitudes towards science and engineering in middle…

  1. Experiments in turbulent pipe flow

    Energy Technology Data Exchange (ETDEWEB)

    Torbergsen, Lars Even

    1998-12-31

    This thesis reports experimental results for the mean velocity and turbulence statistics in two straight pipe sections for bulk Reynolds numbers in the range 22000 to 75000. The flow was found consistent with a fully developed state. Detailed turbulence spectra were obtained for low and moderate turbulent Reynolds number. For the pipe centre line location at R{sub {lambda}} = 112, a narrow range in the streamwise power spectrum applied to the -5/3 inertial subrange. However this range was influenced both by turbulence production and viscous dissipation, and therefore did not reflect a true inertial range. The result indicates how the intermediate range between the production and dissipative scales can be misinterpreted as an inertial range for low and moderate R{sub {lambda}}. To examine the universal behaviour of the inertial range, the inertial scaling of the streamwise power spectrum is compared to the inertial scaling of the second order longitudinal velocity structure function, which relate directly by a Fourier transform. Increasing agreement between the Kolmogorov constant C{sub K} and the second order structure function scaling constant C{sub 2} was observed with increasing R{sub {lambda}}. The result indicates that a true inertial range requires several decades of separation between the energy containing and dissipative scales. A method for examining spectral anisotropy is reported and applied to turbulence spectra in fully developed pipe flow. It is found that the spectral redistribution from the streamwise to the two lateral spectra goes primarily to the circumferential component. Experimental results are reported for an axisymmetric contraction of a fully developed pipe flow. 67 refs., 75 figs., 9 tabs.

  2. CT and MRI findings of 4th ventricular tumors

    International Nuclear Information System (INIS)

    Kim, Taek Geun; Ro, Hee Jeong; Byun, Jae Young; Lee, Han Jin; Chung, Myung Hee; Choi, Kyu Ho; Shinn, Kyung Sub

    1994-01-01

    The purpose of our study is to evaluate characteristic features of 4th ventricular tumors in CT and MRI. Pathologically proved 9 patients with 4th ventricular tumor were examined by CT and/or MRI. 4th ventricular tumors were ependymoma(4 cases), medulloblastoma(2 case), choroid plexus papilloma(2 cases), and oligodendroglioma(1 cases). Include in our study were only those mass lesions that were located at surgery predominantly within 4th ventricle with or without ventricular expansion. The origin of 4th ventricular tumor was the roof (ependymoma 3 cases, medulloblastoma 2 cases), the floor (ependymoma 1 cases), and the undetermined(remaining 3 case). On MRI, all tumors were hypointense except ependymoma (3 cases) showing isointensity on T1WI. All tumors were hypointense on PDWI and T2WI. On Gd-DTPA enhanced T1WI, strong enhancement was seen in all but ependymoma(1 cases) which showed mild enhancement. On CT, as compared with MR images, various density on precontrast and postcontrast images were seen. Calcification was seen in choroid plexus papilloma(1 caes) and oligodendroglioma(1 cases). Hydrocephalus is seen in all cases except ependymoma(2 cases) and oligodendroglioma(1 case). Hemorrhage within tumor was present only in ependymoma(2 cases). Cystic change or necrosis of tumor was seen in ependymoma(3 cases), choroid plexus papilloma(1 case), and oligodendroglioma(1 case). Peritumoral edema was seen in medulloblastoma(1 case). Extension through the foramen Luschka and the Megendie was seen in ependymoma (2 cases), choroid plexus(2 cases), and medulloblastoma (1 case). Seeing along the CSF pathway was seen only in ependymoma(2 case). The results od our study may suggest that specific diagnosis of 4th ventricular tumor can be suggested preoperatively by analysing the origin in 4th ventricle, difference of CT density or MRI signal intensity, presence of extension or seeding through cerebrospinal fluid of the lesion

  3. Smart energy systems and 4th generation district heating

    DEFF Research Database (Denmark)

    Lund, Henrik; Duic, Neven; Østergaard, Poul Alberg

    2016-01-01

    scientific understanding on how we can design and implement a suitable and least-cost transformation into a sustainable energy future. The concept of Smart Energy Systems emphasizes the importance of being coherent and cross-sectoral when the best solutions are to be found and how this also calls......This editorial gives an introduction to the important relationship between Smart Energy Systems and 4th Generation District Heating and presents a number of selected papers from the 1st International Conference on the topic. All of the papers elaborate on or otherwise contribute to the theoretical...... for the active inclusion of the heating and cooling sectors. The concept of 4th Generation District Heating emphasizes that district heating and cooling are both important elements but also technologies that have to be developed further into a 4th generation version to be able to fulfil their roles in future...

  4. Modeling Dexterity Development in 2nd-4th-grade Boys by Means of Active Games

    Directory of Open Access Journals (Sweden)

    C. Марченко

    2017-06-01

    Full Text Available The objective is to optimize the mode of using game for dexterity development in the 2nd-4th-grade boys. Materials & methods: to conduct the experiment, there were eight test groups (n=48 formed in each class. The total number of such test groups was 24. The research relied on the following methods: theoretical analysis and collation of scientific and methodological literature; pedagogical testing; methods of mathematical experiment planning (complete factorial experiment 23; modeling method. Results: the research has determined that to develop dexterity, the 2nd-4th-grade boys need to participate in up to five games. The number of repetitions for the 2nd-3rd-graders is two, and for the 4th-graders – three, with 30–40-second rest intervals. The 2nd-4th-grade boys showed effective development during 40 classes, and the 3rd-grade boys – during 20 classes. After that, we recommend to use other means. The game duration varies from one to two minutes. Conclusions: the analysis of the scientific and methodological literature has revealed that the level of motor readiness, dexterity being one of its main components, largely determines the state of children’s physical and mental health. The research has found that the natural development of coordination abilities in boys aged between 7 and 10 is 22.5–80.0% (56.2% on average. Game actions play a particular role in dexterity development in junior schoolers. The 23 complete factorial experiment made it possible to study the multi-factorial structure of game load for the 2nd-4th-graders; to specify the relations between factors for their use during dexterity development in the 2nd-4th-grade boys in physical education classes. They can serve as an objective tool for the educational process optimization. The given regression equations are models that can be used to determine the optimal game means ratio in the academic process of the 2nd-4th-graders.

  5. Flowing dusty plasma experiments: generation of flow and measurement techniques

    Science.gov (United States)

    Jaiswal, S.; Bandyopadhyay, P.; Sen, A.

    2016-12-01

    A variety of experimental techniques for the generation of subsonic/supersonic dust fluid flows and means of measuring such flow velocities are presented. The experiments have been carried out in a \\Pi -shaped dusty plasma experimental device with micron size kaolin/melamine formaldehyde particles embedded in a background of argon plasma created by a direct current glow discharge. A stationary dust cloud is formed over the cathode region by precisely balancing the pumping speed and gas flow rate. A flow of dust particles/fluid is generated by additional gas injection from a single or dual locations or by altering the dust confining potential. The flow velocity is then estimated by three different techniques, namely, by super particle identification code, particle image velocimetry analysis and the excitation of dust acoustic waves. The results obtained from these three different techniques along with their merits and demerits are discussed. An estimation of the neutral drag force responsible for the generation as well as the attenuation of the dust fluid flow is made. These techniques can be usefully employed in laboratory devices to investigate linear and non-linear collective excitations in a flowing dusty plasma.

  6. 4TH Marine Division Operation Plan Number 49-44

    Science.gov (United States)

    1944-12-26

    Interpretation Squadron TWOC Pt GUAM for processing and inter- pretation. To assist in this work, one photographic interpreter each from Commander Amphibious...Annex "Ain to Division administrativo Order Nio, 43-44, (Reviej)) . (4) Repai~, section to provide 2d, 3d and 4th echelon mainteniaince for Engineer

  7. The 4th technological meeting of Tokai Reprocessing Plant

    International Nuclear Information System (INIS)

    Ohnishi, Tohru; Maki, Akira; Shibata, Satomi; Yatogi, Hideo; Nyui, Daisuke; Hashimoto, Takakazu; Fukuda, Kazuhito; Ohzeki, Tatsuya

    2001-11-01

    ''The 4th technological meeting of Tokai Reprocessing Plant (TRP)'' was held in JNFL Rokkasho site on October 11 th , 2001. The report contains the proceedings, transparencies and questionnaires of the meeting. This time, we reported about ''Maintenance and repair results of Tokai Reprocessing Plant'' based on technology and knowledge accumulated in Tokai Reprocessing Plant. (author)

  8. Proceedings of the 4th Symposium on Laser Spectroscopy

    International Nuclear Information System (INIS)

    1996-11-01

    This proceedings contains articles of the 4th Symposium on Laser Spectroscopy. It was held on Nov 8-9, 1996 in Taejeon, Korea. The main topics are as follows: Laser Isotope, Laser Spectroscopy, Laser Fusion, Laser Applications and so on. (Yi, J. H.)

  9. Improving 4th Grade Primary School Students' Reading Comprehension Skills

    Science.gov (United States)

    Bulut, Aydin

    2017-01-01

    The aim of this study was to carry out action research to investigate reading comprehension skills when using the SQ3R reading comprehension strategy. To that end, this strategy was used for improving the reading comprehension skills of 7 primary school 4th grade students who had problems with these skills. An action plan was prepared for 3hours a…

  10. CFD validation experiments for hypersonic flows

    Science.gov (United States)

    Marvin, Joseph G.

    1992-01-01

    A roadmap for CFD code validation is introduced. The elements of the roadmap are consistent with air-breathing vehicle design requirements and related to the important flow path components: forebody, inlet, combustor, and nozzle. Building block and benchmark validation experiments are identified along with their test conditions and measurements. Based on an evaluation criteria, recommendations for an initial CFD validation data base are given and gaps identified where future experiments could provide new validation data.

  11. Switched Current Micropower 4th Order Lowpass / Highpass Filter

    DEFF Research Database (Denmark)

    Bogason, Gudmundur

    1993-01-01

    This paper describes a 4th order lowpass / highpass Butterworth filter implemented in switched current technique. The filter has been designed for low power operation. A prototype implementation has been made and it operates with supply voltages down to 2V and with a total supply current of 211Â......¿A at a sampling rate of 50kHz. The chip includes a clock-generator, three current-followers, sample-and-hold and two 4th order filters. The sampling frequency is restricted to approximately 50kHz and the ratio between sampling frequency and cutoff frequency is 12.5. The dynamic-range was found to be 49d...

  12. 4th June: AIS and NICE/MAIL unique authentication

    CERN Multimedia

    AIS and NICE teams

    2007-01-01

    Over the past few years, the IT department has been in the process of streamlining CERN users' access to all central computing services. The long term goal is to converge on a unique computer account, which will increase computer security and simplify account maintenance. The next step of this process will occur on 4th June 2007, as of when authenticating on the AIS applications (EDH, HRT, CET, APT, ERT, CRA, Foundation, ...) and on NICE (Windows) and MAIL will be done using the same username and password. As a reminder, this account can also be used on EDMS, INDICO, CDS and SIMBA. So starting on 4th June 2007, authentication on the AIS applications must be done using your AIS username and your MAIL/NICE password. Thanks for your understanding, The AIS and NICE teams

  13. 4th June: AIS and NICE/MAIL unique authentication

    CERN Multimedia

    The AIS and NICE teams

    2007-01-01

    Over the past few years, the IT department has been in the process of streamlining CERN users' access to all central computing services. The long term goal is to converge on a unique computer account, which will increase computer security and simplify account maintenance. The next step of this process will occur on the 4th June 2007, as of when authenticating on the AIS applications (EDH, HRT, CET, APT, ERT, CRA, Foundation, ...) and on NICE (Windows) and MAIL will be done using the same username and password. As a reminder, this account can also be used on EDMS, INDICO, CDS and SIMBA. Thus starting on the 4th June 2007, authentication on the AIS applications must be done using your AIS username and your MAIL/NICE password. Thanks for your understanding, The AIS and NICE teams

  14. 4th international renewable energy storage conference (IRES 2009)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2009-07-01

    Within the 4th International Renewable Energy Storage Conference of The European Association for Renewable Energy (Bonn, Federal Republic of Germany) and The World Council for Renewable Energy (Bonn, Federal Republic of Germany) between 24th and 25 November, 2009, in Berlin (Federal Republic of Germany), the following lectures were held: (1) The World Wind Energy Association (A. Kane); (2) The contribution of wind power to the energy supply of tomorrow (H. Albers); (3) Intelligent energy systems for the integration of renewable energies (A.-C. Agricola); (4) 100% Renewable energies: From fossil baseload plants to renewable plants for basic supply (M. Willenbacher); (5) High-performance Li-ion technology for stationary and mobile applications (A. Gutsch); (6) Energy storage in geological underground - Competition of use at storage formations (L. Dietrich); (7) E-mobility concepts for model region ''Rhein-Ruhr'' in North Rhine Westphalia (G.-U. Funk); (8) Photovoltaic energy storage for a better energy management in residential buildings (S. Pincemin); (9) Self-consuming photovoltaic energy in Germany - Impact on energy flows, business cases, and the distribution grid (M. Braun); (10) Local energy systems -optimized for local consumption of self-produced electricity (B. Wille-Haussmann); (11) Assessing the economics of distributed storage systems at the end consumer level (K.-H. Ahlert); (12) A new transportation system for heat on a wide temperature range (S. Gschwander); (13) Latent heat storage media for cooling applications (C. Doetsch); (14) Numerical and experimental analysis of latent heat storage systems for mobile application (F. Roesler); (15) CO{sub 2}-free heat supply from waste heat (H.-W. Etzkorn); (16) Stationary Li-Ion-technology applications for dispatchable power (C. Kolligs); (17) Redox-flow batteries - Electric storage systems for renewable energy (T. Smolinka); (18) Energy storage by means of flywheels (H. Kielsein); (19

  15. 4th International Conference on Communications, Signal Processing, and Systems

    CERN Document Server

    Mu, Jiasong; Wang, Wei; Zhang, Baoju

    2016-01-01

    This book brings together papers presented at the 4th International Conference on Communications, Signal Processing, and Systems, which provides a venue to disseminate the latest developments and to discuss the interactions and links between these multidisciplinary fields. Spanning topics ranging from Communications, Signal Processing and Systems, this book is aimed at undergraduate and graduate students in Electrical Engineering, Computer Science and Mathematics, researchers and engineers from academia and industry as well as government employees (such as NSF, DOD, DOE, etc).

  16. 4th ENRI International Workshop on ATM/CNS

    CERN Document Server

    2017-01-01

    This book is a compilation of selected papers from the 4th ENRI International Workshop on ATM/CNS (EIWAC2015). The work focuses on novel techniques for aviation infrastructure in air traffic management (ATM) and communications, navigation, surveillance, and informatics (CNSI) domains. The contents make valuable contributions to academic researchers, engineers in the industry, and regulators of aviation authorities. As well, readers will encounter new ideas for realizing a more efficient and safer aviation system. .

  17. Summary of the 4th Nordic Symposium on Digital Pathology.

    Science.gov (United States)

    Lundström, Claes; Waltersson, Marie; Persson, Anders; Treanor, Darren

    2017-01-01

    The Nordic symposium on digital pathology (NDP) was created to promote knowledge exchange across stakeholders in health care, industry, and academia. In 2016, the 4 th NDP installment took place in Linköping, Sweden, promoting development and collaboration in digital pathology for the benefit of routine care advances. This article summarizes the symposium, gathering 170 attendees from 13 countries. This summary also contains results from a survey on integrated diagnostics aspects, in particular radiology-pathology collaboration.

  18. Summary of the 4th nordic symposium on digital pathology

    Directory of Open Access Journals (Sweden)

    Claes Lundström

    2017-01-01

    Full Text Available The Nordic symposium on digital pathology (NDP was created to promote knowledge exchange across stakeholders in health care, industry, and academia. In 2016, the 4th NDP installment took place in Linköping, Sweden, promoting development and collaboration in digital pathology for the benefit of routine care advances. This article summarizes the symposium, gathering 170 attendees from 13 countries. This summary also contains results from a survey on integrated diagnostics aspects, in particular radiology-pathology collaboration.

  19. 4th International Plant Biomechanics Conference Proceedings (Abstracts)

    Energy Technology Data Exchange (ETDEWEB)

    Frank W. Telewski; Lothar H. Koehler; Frank W. Ewers

    2003-07-20

    The 4th International Plant Biomechanics Conference facilitated an interdisciplinary exchange between scientists, engineers, and educators addressing the major questions encountered in the field of Plant Biomechanics. Subjects covered by the conference include: Evolution; Ecology; Mechanoreception; Cell Walls; Genetic Modification; Applied Biomechanics of Whole Plants, Plant Products, Fibers & Composites; Fluid Dynamics; Wood & Trees; Fracture Mechanics; Xylem Pressure & Water Transport; Modeling; and Introducing Plant Biomechanics in Secondary School Education.

  20. Modeling variability in porescale multiphase flow experiments

    Science.gov (United States)

    Ling, Bowen; Bao, Jie; Oostrom, Mart; Battiato, Ilenia; Tartakovsky, Alexandre M.

    2017-07-01

    Microfluidic devices and porescale numerical models are commonly used to study multiphase flow in biological, geological, and engineered porous materials. In this work, we perform a set of drainage and imbibition experiments in six identical microfluidic cells to study the reproducibility of multiphase flow experiments. We observe significant variations in the experimental results, which are smaller during the drainage stage and larger during the imbibition stage. We demonstrate that these variations are due to sub-porescale geometry differences in microcells (because of manufacturing defects) and variations in the boundary condition (i.e., fluctuations in the injection rate inherent to syringe pumps). Computational simulations are conducted using commercial software STAR-CCM+, both with constant and randomly varying injection rates. Stochastic simulations are able to capture variability in the experiments associated with the varying pump injection rate.

  1. Filamentary ion flow theory and experiments

    CERN Document Server

    Lattarulo, Francesco

    2014-01-01

    Presents all-new laboratory-tested theory for calculating more accurate ionized electric fields to aid in designing high-voltage devices and its components Understanding and accurately calculating corona originated electric fields are important issues for scientists who are involved in electromagnetic and electrostatic studies. High-voltage dc lines and equipment, in particular, can generate ion flows that can give rise to environmental inconveniences. Filamentary Ion Flow: Theory and Experiments provides interdisciplinary theoretical arguments to attain a final model for computational elect

  2. Book of abstracts: International Conference on Smart Energy Systems and 4th Generation District Heating

    DEFF Research Database (Denmark)

    , which takes a sole focus on the electricity sector, the smart energy systems approach includes the entire energy system in its identification of suitable energy infrastructure designs and operation strategies. Focusing solely on the smart electricity grid often leads to the definition of transmission......It is a great pleasure to welcome you to the first International Conference on Smart Energy Systems and 4th Generation District Heating at Aalborg University, Copenhagen Campus on 25-26 August 2015. The conference is organised by the 4DH Strategic Research Centre in collaboration with Aalborg...... University and offers more than 70 presentations in 3 parallel sessions with more than 180 participants from 25 countries around the world. The aim is to present and discuss scientific findings and industrial experiences related to the development of Smart Energy Systems and future 4th Generation District...

  3. 76 FR 37649 - Safety Zone; Northern California Annual Fireworks Events, July 4th Fireworks Display

    Science.gov (United States)

    2011-06-28

    ... Zone; Northern California Annual Fireworks Events, July 4th Fireworks Display AGENCY: Coast Guard, DHS... annual July 4th Fireworks Display (Tahoe City 4th of July Fireworks Display). This action is necessary to... INFORMATION: The Coast Guard will enforce the safety zone for the annual Tahoe City 4th of July Fireworks in...

  4. Modeling reproducibility of porescale multiphase flow experiments

    Science.gov (United States)

    Ling, B.; Tartakovsky, A. M.; Bao, J.; Oostrom, M.; Battiato, I.

    2017-12-01

    Multi-phase flow in porous media is widely encountered in geological systems. Understanding immiscible fluid displacement is crucial for processes including, but not limited to, CO2 sequestration, non-aqueous phase liquid contamination and oil recovery. Microfluidic devices and porescale numerical models are commonly used to study multiphase flow in biological, geological, and engineered porous materials. In this work, we perform a set of drainage and imbibition experiments in six identical microfluidic cells to study the reproducibility of multiphase flow experiments. We observe significant variations in the experimental results, which are smaller during the drainage stage and larger during the imbibition stage. We demonstrate that these variations are due to sub-porescale geometry differences in microcells (because of manufacturing defects) and variations in the boundary condition (i.e.,fluctuations in the injection rate inherent to syringe pumps). Computational simulations are conducted using commercial software STAR-CCM+, both with constant and randomly varying injection rate. Stochastic simulations are able to capture variability in the experiments associated with the varying pump injection rate.

  5. Report of the 4th European Zebrafish Principal Investigator Meeting.

    Science.gov (United States)

    Lopes, Susana S; Distel, Martin; Linker, Claudia; Fior, Rita; Monteiro, Rui; Bianco, Isaac H; Portugues, Ruben; Strähle, Uwe; Saúde, Leonor

    2016-12-01

    The European Zebrafish Principal Investigator Meeting (EZPM) is an ideal forum for group leaders using this fantastic animal model not only to discuss science but also to strengthen their interactions, to push forward technological advances, and to define guidelines for the use of this fish in research. The city of Lisbon (Portugal) was voted by the European group leaders to be the setting for the 4th EZPM, and the organizing committee, composed by Leonor Saúde (iMM Lisboa, PT), Susana Lopes (CEDOC, PT), Michael Orger (Champalimaud Foundation, PT), Rui Oliveira (ISPA, PT), and António Jacinto (CEDOC, PT), was very enthusiastic to organize a productive event. The 4th EZPM took place from March 15 to 19 at Pavilhão do Conhecimento, a Science Museum and Educational Center winner of The Great Prize FAD of Arquitecture 1999 and The Society for Environmental Graphic Design Award 2011. Over 5 days, 135 group leaders (89 men and 46 women) coming from 19 different European countries and also from the United States, Turkey, Israel, Chile, and Singapore presented and discussed their recent research achievements. In addition to the scientific oral and poster presentations, the group leaders gathered in very lively community sessions on morphants versus mutants (chaired by Didier Stainier, Max Planck Institute for Heart and Lung Research, DE), funding issues (chaired by Uwe Strahle, KIT-ITG, DE), and gender equality (chaired by Corinne Houart, KCL, United Kingdom). One of the highlights of the 4th EZPM was the guided visit to Oceanário de Lisboa, an international award-winning place that celebrates life with a stunning display of living aquatic creatures.

  6. Report from the 4th Workshop on Extremely Large Databases

    Directory of Open Access Journals (Sweden)

    Jacek Becla

    2011-02-01

    Full Text Available Academic and industrial users are increasingly facing the challenge of petabytes of data, but managing and analyzing such large data sets still remains a daunting task. The 4th Extremely Large Databases workshop was organized to examine the needs of communities under-represented at the past workshops facing these issues. Approaches to big data statistical analytics as well as emerging opportunities related to emerging hardware technologies were also debated. Writable extreme scale databases and the science benchmark were discussed. This paper is the final report of the discussions and activities at this workshop.

  7. A real CDIO mechanical engineering project in 4th semester

    DEFF Research Database (Denmark)

    Lauritsen, Aage Birkkjær

    In the past 6 years at the mechanical engineering study at the Engineering College of Aarhus we have been practicing project work on 4th Semester in the design of energy technology systems. In my presentation, I will give a description of the project, and the thoughts behind; pedagogic......-6 students, and will partly support the general theory being taught in the courses, but will also provide students with skills in teamwork, project work and system building. The pedagogical considerations behind the development of the project are quite simply that students learn best through active work...

  8. 4th International conference on Knowledge Discovery and Data Mining

    CERN Document Server

    Knowledge Discovery and Data Mining

    2012-01-01

    The volume includes a set of selected papers extended and revised from the 4th International conference on Knowledge Discovery and Data Mining, March 1-2, 2011, Macau, Chin.   This Volume is to provide a forum for researchers, educators, engineers, and government officials involved in the general areas of knowledge discovery and data mining and learning to disseminate their latest research results and exchange views on the future research directions of these fields. 108 high-quality papers are included in the volume.

  9. 4th International Conference on Sustainable Design and Manufacturing

    CERN Document Server

    Howlett, Robert; Setchi, Rossi; Cimatti, Barbara

    2017-01-01

    This volume includes papers presented at the 4th International Conference on Sustainable Design and Manufacturing (SDM-17) held in Bologna, Italy, in April 2017. The conference covered a wide range of topics from cutting-edge sustainable product design and service innovation, sustainable processes and technology for the manufacturing of sustainable products, sustainable manufacturing systems and enterprises, decision support for sustainability, and the study of the societal impact of sustainability including research for circular economy. Application areas are wide and varied, and the book provides an excellent overview of the latest research and development in the area of Sustainable Design and Manufacturing.

  10. 4th International Conference on Soft Computing for Problem Solving

    CERN Document Server

    Deep, Kusum; Pant, Millie; Bansal, Jagdish; Nagar, Atulya

    2015-01-01

    This two volume book is based on the research papers presented at the 4th International Conference on Soft Computing for Problem Solving (SocProS 2014) and covers a variety of topics, including mathematical modelling, image processing, optimization methods, swarm intelligence, evolutionary algorithms, fuzzy logic, neural networks, forecasting, medical and healthcare, data mining, etc. Mainly the emphasis is on Soft Computing and its applications in diverse areas. The prime objective of this book is to familiarize the reader with the latest scientific developments in various fields of Science, Engineering and Technology and is directed to the researchers and scientists engaged in various real-world applications of ‘Soft Computing’.

  11. Exploring Online Game Players' Flow Experiences and Positive Affect

    Science.gov (United States)

    Chiang, Yu-Tzu; Lin, Sunny S. J.; Cheng, Chao-Yang; Liu, Eric Zhi-Feng

    2011-01-01

    The authors conducted two studies to explore online game players' flow experiences and positive affect. Our findings indicated that online game are capable of evoking flow experiences and positive affect, and games of violent or nonviolent type may not arouse players' aggression. The players could be placed into four flow conditions: flow,…

  12. Coding Theory and Applications : 4th International Castle Meeting

    CERN Document Server

    Malonek, Paula; Vettori, Paolo

    2015-01-01

    The topics covered in this book, written by researchers at the forefront of their field, represent some of the most relevant research areas in modern coding theory: codes and combinatorial structures, algebraic geometric codes, group codes, quantum codes, convolutional codes, network coding and cryptography. The book includes a survey paper on the interconnections of coding theory with constrained systems, written by an invited speaker, as well as 37 cutting-edge research communications presented at the 4th International Castle Meeting on Coding Theory and Applications (4ICMCTA), held at the Castle of Palmela in September 2014. The event’s scientific program consisted of four invited talks and 39 regular talks by authors from 24 different countries. This conference provided an ideal opportunity for communicating new results, exchanging ideas, strengthening international cooperation, and introducing young researchers into the coding theory community.

  13. 4th International Conference on Sustainable Automotive Technologies

    CERN Document Server

    Wellnitz, Jörg; Leary, Martin; Koopmans, Lucien

    2012-01-01

    The book on Sustainable Automotive Technologies aims to draw special attention to the research and practice focused on new technologies and approaches capable of meeting the challenges to sustainable mobility. In particular, the book features incremental and radical technical advancements that are able to meet social, economic and environmental targets in both local and global contexts. These include original solutions to the problems of pollution and congestion, vehicle and public safety, sustainable vehicle design and manufacture, new structures and materials, new power-train technologies and vehicle concepts. In addition to vehicle technologies, the book is also concerned with the broader systemic issues such as sustainable supply chain systems, integrated logistics and telematics, and end-of-life vehicle management. It captures selected peer reviewed papers accepted for presentation at the 4th International Conference on Sustainable Automotive Technologies, ICSAT2012, held at the RMIT, Melbourne, Australi...

  14. 4th International Conference on Robot Intelligence Technology and Applications

    CERN Document Server

    Karray, Fakhri; Jo, Jun; Sincak, Peter; Myung, Hyun

    2017-01-01

    This book covers all aspects of robot intelligence from perception at sensor level and reasoning at cognitive level to behavior planning at execution level for each low level segment of the machine. It also presents the technologies for cognitive reasoning, social interaction with humans, behavior generation, ability to cooperate with other robots, ambience awareness, and an artificial genome that can be passed on to other robots. These technologies are to materialize cognitive intelligence, social intelligence, behavioral intelligence, collective intelligence, ambient intelligence and genetic intelligence. The book aims at serving researchers and practitioners with a timely dissemination of the recent progress on robot intelligence technology and its applications, based on a collection of papers presented at the 4th International Conference on Robot Intelligence Technology and Applications (RiTA), held in Bucheon, Korea, December 14 - 16, 2015. For better readability, this edition has the total of 49 article...

  15. 2015 4th China Academic Conference on Printing and Packaging

    CERN Document Server

    Xu, Min; Yang, Li; Ouyang, Yujie

    2016-01-01

    This book includes a selection of reviewed papers presented at the 2015, 4th China Academic Conference on Printing and Packaging, which was held on October 22-24, 2015 in Hangzhou, China. The conference was jointly organized by the China Academy of Printing Technology, Beijing Institute of Graphic Communication, and Hangzhou Dianzi University. With 3 keynote talks and 200 presented papers on graphic communications, packaging technologies and materials, the conference attracted more than 400 scientists.  These proceedings cover the recent research outcomes on color science and technology, image-processing technology, digital-media technology, printing-engineering technology, packaging-engineering technology etc. They will be of interest to university researchers, R&D engineers and graduate students in graphic communications, packaging, color science, image science, materials science, computer science, digital media and network technology fields.

  16. 4th International Conference on Computer Engineering and Networks

    CERN Document Server

    2015-01-01

    This book aims to examine innovation in the fields of computer engineering and networking. The book covers important emerging topics in computer engineering and networking, and it will help researchers and engineers improve their knowledge of state-of-art in related areas. The book presents papers from the 4th International Conference on Computer Engineering and Networks (CENet2014) held July 19-20, 2014 in Shanghai, China.  ·       Covers emerging topics for computer engineering and networking ·       Discusses how to improve productivity by using the latest advanced technologies ·       Examines innovation in the fields of computer engineering and networking  

  17. 4th International Conference on Structural Nonlinear Dynamics and Diagnosis

    CERN Document Server

    2018-01-01

    This book presents contributions on the most active lines of recent advanced research in the field of nonlinear mechanics and physics selected from the 4th International Conference on Structural Nonlinear Dynamics and Diagnosis. It includes fifteen chapters by outstanding scientists, covering various aspects of applications, including road tanker dynamics and stability, simulation of abrasive wear, energy harvesting, modeling and analysis of flexoelectric nanoactuator, periodic Fermi–Pasta–Ulam problems, nonlinear stability in Hamiltonian systems, nonlinear dynamics of rotating composites, nonlinear vibrations of a shallow arch, extreme pulse dynamics in mode-locked lasers, localized structures in a photonic crystal fiber resonator, nonlinear stochastic dynamics, linearization of nonlinear resonances, treatment of a linear delay differential equation, and fractional nonlinear damping. It appeals to a wide range of experts in the field of structural nonlinear dynamics and offers researchers and engineers a...

  18. Proceedings of the 4th workshop on WENDELSTEIN 7-X

    International Nuclear Information System (INIS)

    Junker, J.

    1991-12-01

    The 4th Workshop on WENDELSTEIN 7-x (28.-31.10.1991) treated the following topics: Coil System (optimization; ripple transport; magnetic fields, forces, stresses; analytic stellarator fields) - equilibrium and stability (computations; equilibrium with dissipation; global MHD stability; resistive ballooning modes) - transport and neutral gas (Pfirsch-Schlueter currents and anomalous transport; general solution of the ripple-averaged equation; the EIRENE neutral gas transport codes; application of DEGAS; CX-losses at NBI) - plasma parameters (alpha particle confinement in stellarators; the radical electric field in W 7) - divertor (structure of the magnetic field line diversion in Helias configurations; divertor studies for W 7; sweep coil system; the island divertor; one-dimensional fluid model and investigation of the plasma boundary layer) - engineering (W 7 status of planning; CAD/CAE applications for W 7; structural analysis of the coil system) - reactor (the Helias reactor) - concluding discussion. (AH)

  19. 4th International Conference on Frontiers in Global Optimization

    CERN Document Server

    Pardalos, Panos

    2004-01-01

    Global Optimization has emerged as one of the most exciting new areas of mathematical programming. Global optimization has received a wide attraction from many fields in the past few years, due to the success of new algorithms for addressing previously intractable problems from diverse areas such as computational chemistry and biology, biomedicine, structural optimization, computer sciences, operations research, economics, and engineering design and control. This book contains refereed invited papers submitted at the 4th international confer­ ence on Frontiers in Global Optimization held at Santorini, Greece during June 8-12, 2003. Santorini is one of the few sites of Greece, with wild beauty created by the explosion of a volcano which is in the middle of the gulf of the island. The mystic landscape with its numerous mult-extrema, was an inspiring location particularly for researchers working on global optimization. The three previous conferences on "Recent Advances in Global Opti­ mization", "State-of-the-...

  20. 4th International Conference on Dynamics in Logistics

    CERN Document Server

    Pannek, Jürgen; Thoben, Klaus-Dieter

    2016-01-01

    This contributed volume brings together research papers presented at the 4th International Conference on Dynamics in Logistics, held in Bremen, Germany in February 2014. The conference focused on the identification, analysis and description of the dynamics of logistics processes and networks. Topics covered range from the modeling and planning of processes, to innovative methods like autonomous control and knowledge management, to the latest technologies provided by radio frequency identification, mobile communication, and networking. The growing dynamic poses wholly new challenges: logistics processes and networks must be(come) able to rapidly and flexibly adapt to constantly changing conditions. The book primarily addresses the needs of researchers and practitioners from the field of logistics, but will also be beneficial for graduate students.

  1. Participants at the 4th Controlling Conference of International Public Organisations

    CERN Multimedia

    Jean-Claude Gadmer

    2010-01-01

    The 4th Controlling Conference of International Public Organisations is part of a cycle of yearly conferences which were held the previous years in Frankfurt, Munich, Luxemburg, and which will take place this year on 31 May and 1 June at CERN. The aim of these conferences is to offer a forum for Directors of Administration, Deputy CFOs, Secretary-Generals, Heads of Budget of International Organisations, to exchange experiences on selected themes related to performance management. This year’s theme is “The Reduction of Overheads in International Public Organisations”.

  2. Proceedings of the 4th Australian experimental high energy physics meeting and workshop

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-12-31

    The 4th Annual Meeting of the Australian High Energy Physics Consortium was held at ANSTO on the 11th and 12th of December, with a workshop on software development and applications held at the University f Sydney on the 13th. A wide range of talks on the progress of NOMAD and ATLAS experiments and related research were presented, plus talks on heavy ion physics which is also carried out in collaboration with CERN. Extended abstracts of the presentations are included in this volume.

  3. Proceedings of the 4th Australian experimental high energy physics meeting and workshop

    International Nuclear Information System (INIS)

    1995-01-01

    The 4th Annual Meeting of the Australian High Energy Physics Consortium was held at ANSTO on the 11th and 12th of December, with a workshop on software development and applications held at the University f Sydney on the 13th. A wide range of talks on the progress of NOMAD and ATLAS experiments and related research were presented, plus talks on heavy ion physics which is also carried out in collaboration with CERN. Extended abstracts of the presentations are included in this volume

  4. Proceedings of the 4th Australian experimental high energy physics meeting and workshop

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1995-12-31

    The 4th Annual Meeting of the Australian High Energy Physics Consortium was held at ANSTO on the 11th and 12th of December, with a workshop on software development and applications held at the University f Sydney on the 13th. A wide range of talks on the progress of NOMAD and ATLAS experiments and related research were presented, plus talks on heavy ion physics which is also carried out in collaboration with CERN. Extended abstracts of the presentations are included in this volume.

  5. 4-th EPRI International conference on the water chemistry of the organic-fuel thermal power plants

    International Nuclear Information System (INIS)

    Petrova, T.I.; Martynova, O.I.

    1995-01-01

    Most actual problems on thermal power engineering are discussed at EPRI conferences on organic fuel, conducted every two years. Experience in realization of economically beneficial, ecologically feasible modes and their monitoring, accumulated in recent years, was formulated at the 4-th conference with wide participation

  6. Human behaviour towards climatic change during the 4th millennium BC in the Swiss Alpine forelands

    DEFF Research Database (Denmark)

    Karg, Sabine

    Human behaviour towards climatic change during the 4th millennium BC in the Swiss Alpine forelands.......Human behaviour towards climatic change during the 4th millennium BC in the Swiss Alpine forelands....

  7. 77 FR 30242 - Safety Zone; City of Tonawanda July 4th Celebration, Niagara River, Tonawanda, NY

    Science.gov (United States)

    2012-05-22

    ...-AA00 Safety Zone; City of Tonawanda July 4th Celebration, Niagara River, Tonawanda, NY AGENCY: Coast... vessels from a portion of the Niagara River during the City of Tonawanda July 4th Celebration fireworks... read as follows: Sec. 165.T09-0352 Safety Zone; City of Tonawanda July 4th Celebration, Niagara River...

  8. 76 FR 37650 - Safety Zone; 4th of July Festival Berkeley Marina Fireworks Display Berkeley, CA

    Science.gov (United States)

    2011-06-28

    ...-AA00 Safety Zone; 4th of July Festival Berkeley Marina Fireworks Display Berkeley, CA AGENCY: Coast... the 4th of July Festival Berkeley Marina Fireworks Display. Unauthorized persons or vessels are... display. Background and Purpose The City of Berkeley Marina will sponsor the 4th of July Festival Berkeley...

  9. 77 FR 40266 - Safety Zone; Conneaut 4th of July Festival, Lake Erie, Conneaut, OH

    Science.gov (United States)

    2012-07-09

    ... 1625-AA00 Safety Zone; Conneaut 4th of July Festival, Lake Erie, Conneaut, OH AGENCY: Coast Guard, DHS... the Conneaut 4th of July Festival Fireworks display. This temporary safety zone is necessary to... vessels during the Conneaut 4th of July Festival Fireworks. This zone will be effective and enforced from...

  10. 77 FR 35619 - Safety Zone; Old Fashion 4th July Fireworks, Presque Isle Bay, Erie, PA

    Science.gov (United States)

    2012-06-14

    ...-AA00 Safety Zone; Old Fashion 4th July Fireworks, Presque Isle Bay, Erie, PA AGENCY: Coast Guard, DHS... during the Old Fashion 4th July Fireworks display. This temporary safety zone is necessary to protect... ensure the safety of spectators and vessels during the Old Fashion 4th July Fireworks. [[Page 35620...

  11. The 4th international colloquium on process simulation. Proceedings

    Energy Technology Data Exchange (ETDEWEB)

    Jokilaakso, A [Helsinki Univ. of Technology, Otaniemi (Finland). Dept. of Materials Science and Metallurgy

    1998-12-31

    The papers collected in this volume were presented at the 4th Colloquium on Process Simulation held at Helsinki University of Technology, Espoo, Finland, June 11-13, 1997. In the more developed industrial nations, the processes for producing chemicals, energy, and materials encounter environmental concern and laws which challenge engineers to develop the processes towards more efficient, economical and safe operation. This necessitates more thorough understanding of the processes and phenomena involved. Formerly, the development of the processes was largely based on trial and error, whereas today, the development of computer performance together with the diversification of modelling software enables simulation of the processes. The increased capacity and possibilities for modelling the processes brought by the improved hardware and software, have generated a strong demand for more accurate mathematical descriptions of the processes. Especially, the coupling of computational fluid dynamics and chemical kinetics, combustion, and thermodynamics is of current interest in process oriented technology. This colloquium attempts to give examples of modelling efforts in operation in different universities, research institutes and companies. Furthermore, the aim of this colloquium is to offer an annual opportunity to the researchers to come together and discuss their common problems and the state of their investigations

  12. Modelling of Technological Solutions to 4th Generation DH Systems

    Directory of Open Access Journals (Sweden)

    Vigants Edgars

    2017-11-01

    Full Text Available Flue gas evaporation and condensing processes are investigated in a direct contact heat exchanger - condensing unit, which is installed after a furnace. By using equations describing processes of heat and mass transfer, as well as correlation coherences for determining wet gas parameters, a model is formed to create a no-filling, direct contact heat exchanger. Results of heating equipment modelling and experimental research on the gas condensing unit show, that the capacity of the heat exchanger increases, when return temperature of the district heating network decreases. In order to explain these alterations in capacity, the character of the changes in water vapour partial pressure, in the propelling force of mass transfer, in gas and water temperatures and in the determining parameters of heat transfer are used in this article. The positive impact on the direct contact heat exchanger by the decreased district heating (DH network return temperature shows that introduction of the 4th generation DH system increases the energy efficiency of the heat exchanger. In order to make an assessment, the methodology suggested in the paper can be used in each particular situation.

  13. The 4th Civil Support Team (Weapons of Mass Destruction)

    International Nuclear Information System (INIS)

    Smith, D. L.

    2007-01-01

    The 4th CST (WMD) is a 22 person joint staffed AGR (Active Guard Reserve) unit of the Georgia National Guard. The team is one of 55 CSTs that are charged with responding to a CBRNE (Chemical, Biological, Radiological, Nuclear, and High Yield Explosive) incident within the United States and its Territories. The mission statements of the CTS is to support civil authorities at a domestic CBRNE incident by identifying CBRNE agents/substances, assessing current and projected consequences, advising on response measures, and assisting with appropriate requests for state support. The team possesses the capability to deploy by sea, air, and land in response to a terrorist attack or natural disaster. The team is comprised of seven officers and fifteen non-commissioned officers who are cross trained in a variety of military disciplines. Equipment assigned to the team includes an Analytical Lab, Communications Suite, Tactical Operations Center, closed and open circuit breathing gear, portable and handheld detectors, and decon support. The CSts are activated through a state's emergency response network.(author)

  14. The 4th international colloquium on process simulation. Proceedings

    Energy Technology Data Exchange (ETDEWEB)

    Jokilaakso, A. [Helsinki Univ. of Technology, Otaniemi (Finland). Dept. of Materials Science and Metallurgy

    1997-12-31

    The papers collected in this volume were presented at the 4th Colloquium on Process Simulation held at Helsinki University of Technology, Espoo, Finland, June 11-13, 1997. In the more developed industrial nations, the processes for producing chemicals, energy, and materials encounter environmental concern and laws which challenge engineers to develop the processes towards more efficient, economical and safe operation. This necessitates more thorough understanding of the processes and phenomena involved. Formerly, the development of the processes was largely based on trial and error, whereas today, the development of computer performance together with the diversification of modelling software enables simulation of the processes. The increased capacity and possibilities for modelling the processes brought by the improved hardware and software, have generated a strong demand for more accurate mathematical descriptions of the processes. Especially, the coupling of computational fluid dynamics and chemical kinetics, combustion, and thermodynamics is of current interest in process oriented technology. This colloquium attempts to give examples of modelling efforts in operation in different universities, research institutes and companies. Furthermore, the aim of this colloquium is to offer an annual opportunity to the researchers to come together and discuss their common problems and the state of their investigations

  15. Modelling of Technological Solutions to 4th Generation DH Systems

    Science.gov (United States)

    Vigants, Edgars; Prodanuks, Toms; Vigants, Girts; Veidenbergs, Ivars; Blumberga, Dagnija

    2017-11-01

    Flue gas evaporation and condensing processes are investigated in a direct contact heat exchanger - condensing unit, which is installed after a furnace. By using equations describing processes of heat and mass transfer, as well as correlation coherences for determining wet gas parameters, a model is formed to create a no-filling, direct contact heat exchanger. Results of heating equipment modelling and experimental research on the gas condensing unit show, that the capacity of the heat exchanger increases, when return temperature of the district heating network decreases. In order to explain these alterations in capacity, the character of the changes in water vapour partial pressure, in the propelling force of mass transfer, in gas and water temperatures and in the determining parameters of heat transfer are used in this article. The positive impact on the direct contact heat exchanger by the decreased district heating (DH) network return temperature shows that introduction of the 4th generation DH system increases the energy efficiency of the heat exchanger. In order to make an assessment, the methodology suggested in the paper can be used in each particular situation.

  16. 4th annual Safety Day: full of colour!

    CERN Multimedia

    HSE Unit

    2014-01-01

    On Thursday 10 April, more than 240 people took part in the 4th annual Safety Day, organised on the occasion of the World Day for Safety and Health at Work. The HSE Unit, in partnership with the Fire Brigade (GS/FB) and the TE and BE Departments, organised various stands and activities connected with this year’s theme, chosen by the International Labour Organization: "Safety and health in the use of chemicals at work”.   The stands, set up at lunchtime in all three of CERN’s restaurants as well as in the entrance hall of Building 500, were designed to: Remind visitors of the need to use personal protective equipment appropriate to the chemicals they are using; Make visitors aware of the potential environmental impact of using chemicals; Encourage visitors to always read the labels and safety data sheets of dangerous chemicals and everyday domestic products; Inform visitors that a safety training course called “Chemical Risk Awareness&r...

  17. 4th French-German Conference on Optimization

    CERN Document Server

    Zowe, Jochem; Hiriart-Urruty, Jean-Baptiste; Lemarechal, Claude

    1988-01-01

    This volume contains a collection of 23 papers presented at the 4th French-German Conference on Optimization, hold at Irsee, April 21 - 26, 1986. The conference was aUended by ninety scientists: about one third from France, from Germany and from third countries each. They all contributed to a highly interesting and stimulating meeting. The scientifique program consisted of four survey lectures of a more tutorical character and of 61 contributed papers covering almost all areas of optimization. In addition two informal evening sessions and a plenary discussion on further developments of optimization theory were organized. One of the main aims of the organizers was to indicate and to stress the increasing importance of optimization methods for almost all areas of science and for a fast growing number of industry branches. We hope that the conference approached this goal in a certain degree and managed to continue fruitful discussions between -theory­ and -applications-. Equally important to the official contri...

  18. Centrifuge in space fluid flow visualization experiment

    Science.gov (United States)

    Arnold, William A.; Wilcox, William R.; Regel, Liya L.; Dunbar, Bonnie J.

    1993-01-01

    A prototype flow visualization system is constructed to examine buoyancy driven flows during centrifugation in space. An axial density gradient is formed by imposing a thermal gradient between the two ends of the test cell. Numerical computations for this geometry showed that the Prandtl number plays a limited part in determining the flow.

  19. Flow boiling in microgap channels experiment, visualization and analysis

    CERN Document Server

    Alam, Tamanna; Jin, Li-Wen

    2013-01-01

    Flow Boiling in Microgap Channels: Experiment, Visualization and Analysis presents an up-to-date summary of the details of the confined to unconfined flow boiling transition criteria, flow boiling heat transfer and pressure drop characteristics, instability characteristics, two phase flow pattern and flow regime map and the parametric study of microgap dimension. Advantages of flow boiling in microgaps over microchannels are also highlighted. The objective of this Brief is to obtain a better fundamental understanding of the flow boiling processes, compare the performance between microgap and c

  20. Do Students Experience Flow Conditions Online?

    Science.gov (United States)

    Meyer, Katrina A.; Jones, Stephanie J.

    2013-01-01

    This pilot study asked graduate students enrolled in higher education programs at two institutions to ascertain whether and to what extent they experienced nine flow-related conditions in two settings: (1) online courses or (2) surfing or gaming online. In both settings, flow was experienced "sometimes," although no significant…

  1. Assessment of passive safety injection systems of ALWRs. Final report of the European Commission 4th framework programme. Project FI4I-CT95-004 (APSI)

    Energy Technology Data Exchange (ETDEWEB)

    Tuunanen, J. [VTT Energy, Espoo (Finland). Nuclear Energy; Vihavainen, J. [Lappeenranta Univ. of Technology (Finland); D' Auria, F. [Univ. of Pisa (Italy); Kimber, G. [AEA Technology (United Kingdom)

    1999-07-01

    The European Commission 4th Framework Programme project 'Assessment of Passive Safety Injection Systems of Advanced Light Water Reactors (FI4I-CT95-0004)' involved experiments on the PACTEL test facility and computer simulations of selected experiments. The experiments focused on the performance of Passive Safety Injection Systems (PSIS) of Advanced Light Water Reactors (ALWRs) in Small Break Loss-Of-Coolant Accident (SBLOCA) conditions. The PSIS consisted of a Core Make-up Tank (CMT) and two pipelines. A pressure balancing line (PBL) connected the CMT to one cold leg. The injection line (IL) connected it to the downcomer. The project involved 15 experiments in three series. The experiments provided valuable information about condensation and heat transfer processes in the CMT, thermal stratification of water in the CMT, and natural circulation flow through the PSIS lines. The experiments showed the examined PSIS works efficiently in SBLOCAs although the flow through the PSIS may stop in very small SBLOCAs, when the hot water fills the CMT. The experiments also demonstrated the importance of flow distributor (sparger) in the CMT to limit rapid condensation. The project included validation of three thermal-hydraulic computer codes (APROS, CATHARE and RELAP5). The analyses showed the codes are capable of simulating the overall behaviour of the transients. The codes predicted accurately the core heatup, which occurred when the primary coolant inventory was reduced so much that the core top became free of water. The detailed analyses of the calculation results showed that some models in the codes still need improvements. Especially, further development of models for thermal stratification, condensation and natural circulation flow with small driving forces would be necessary for accurate simulation of phenomena in the PSIS. (orig.)

  2. Assessment of passive safety injection systems of ALWRs. Final report of the European Commission 4th framework programme. Project FI4I-CT95-004 (APSI)

    International Nuclear Information System (INIS)

    Tuunanen, J.; D'Auria, F.; Kimber, G.

    1999-01-01

    The European Commission 4th Framework Programme project 'Assessment of Passive Safety Injection Systems of Advanced Light Water Reactors (FI4I-CT95-0004)' involved experiments on the PACTEL test facility and computer simulations of selected experiments. The experiments focused on the performance of Passive Safety Injection Systems (PSIS) of Advanced Light Water Reactors (ALWRs) in Small Break Loss-Of-Coolant Accident (SBLOCA) conditions. The PSIS consisted of a Core Make-up Tank (CMT) and two pipelines. A pressure balancing line (PBL) connected the CMT to one cold leg. The injection line (IL) connected it to the downcomer. The project involved 15 experiments in three series. The experiments provided valuable information about condensation and heat transfer processes in the CMT, thermal stratification of water in the CMT, and natural circulation flow through the PSIS lines. The experiments showed the examined PSIS works efficiently in SBLOCAs although the flow through the PSIS may stop in very small SBLOCAs, when the hot water fills the CMT. The experiments also demonstrated the importance of flow distributor (sparger) in the CMT to limit rapid condensation. The project included validation of three thermal-hydraulic computer codes (APROS, CATHARE and RELAP5). The analyses showed the codes are capable of simulating the overall behaviour of the transients. The codes predicted accurately the core heatup, which occurred when the primary coolant inventory was reduced so much that the core top became free of water. The detailed analyses of the calculation results showed that some models in the codes still need improvements. Especially, further development of models for thermal stratification, condensation and natural circulation flow with small driving forces would be necessary for accurate simulation of phenomena in the PSIS. (orig.)

  3. Therapeutic experiences of community gardens: putting flow in its place.

    Science.gov (United States)

    Pitt, Hannah

    2014-05-01

    This paper develops the concept of therapeutic place experiences by considering the role of activity. Research of community gardening finds that particular tasks are therapeutic and exhibit the characteristics of flow, but those who lack influence over their community gardening are less likely to benefit from flow as their sense of control is reduced. The notion of emplaced flow is proposed to locate individual experiences amongst socio-spatial factors which limit self-determinacy and therefore affect wellbeing. Emplacing flow prompts critical reflection on who is excluded from therapeutic place experiences, and whether sites offering momentary escape have an enduring impact on wellbeing. Copyright © 2014 Elsevier Ltd. All rights reserved.

  4. FLOW TESTING AND ANALYSIS OF THE FSP-1 EXPERIMENT

    Energy Technology Data Exchange (ETDEWEB)

    Hawkes, Grant L.; Jones, Warren F.; Marcum, Wade; Weiss, Aaron; Howard, Trevor

    2017-06-01

    The U.S. High Performance Research Reactor Conversions fuel development team is focused on developing and qualifying the uranium-molybdenum (U-Mo) alloy monolithic fuel to support conversion of domestic research reactors to low enriched uranium. Several previous irradiations have demonstrated the favorable behavior of the monolithic fuel. The Full Scale Plate 1 (FSP-1) fuel plate experiment will be irradiated in the northeast (NE) flux trap of the Advanced Test Reactor (ATR). This fueled experiment contains six aluminum-clad fuel plates consisting of monolithic U-Mo fuel meat. Flow testing experimentation and hydraulic analysis have been performed on the FSP-1 experiment to be irradiated in the ATR at the Idaho National Laboratory (INL). A flow test experiment mockup of the FSP-1 experiment was completed at Oregon State University. Results of several flow test experiments are compared with analyses. This paper reports and shows hydraulic analyses are nearly identical to the flow test results. A water velocity of 14.0 meters per second is targeted between the fuel plates. Comparisons between FSP-1 measurements and this target will be discussed. This flow rate dominates the flow characteristics of the experiment and model. Separate branch flows have minimal effect on the overall experiment. A square flow orifice was placed to control the flowrate through the experiment. Four different orifices were tested. A flow versus delta P curve for each orifice is reported herein. Fuel plates with depleted uranium in the fuel meat zone were used in one of the flow tests. This test was performed to evaluate flow test vibration with actual fuel meat densities and reported herein. Fuel plate deformation tests were also performed and reported.

  5. Flow transients experiments with refrigerant-12

    International Nuclear Information System (INIS)

    Celata, G.P.; D'Annibale, F.; Farello, G.E.; Setaro, T.

    1986-01-01

    Flow transients have been investigated in a wide range of thermal-hydraulics situations with Refrigerannt-12. Six pressures (including the reference to PWR and BWR characteristic liquid to vapour densities ratios), several periods of the flowrate transients coastdown during the simulated flow decays, and different specific mass flowrate have been studied emploiyng a circular duct test section (Dsub(i)=7,5 mm). Two heated lengths of the test section have been considered (L = 2300 and 1180 mm). Experimental data have shown the complete inadequacy of steady-state critical heat flux correlations in predicting the onset of boiling crisis during fast flow transients (half-flow decay time, tsub(h)lt5.0-6.0 s). The flow transient does not show dependence, in terms of DNB conditions ,upon the length of the test section: the ratio between transient and steady-state critical mass flowrate is not dependent on the tested geometry. The time interval from the start of the flowrate transient to the onset of DNB (time to crisis), has been experimentally determined for all the runs. Data analysis for a better theoretical prediction of the phenomenon has been accomplished, and a design correlation for DNB conditons and time to crisis prediction has been proposed

  6. Relationship of workplace violence and perpetrators on sleep disturbance-data from the 4th Korean working conditions survey

    OpenAIRE

    Yoo, Taejun; Ye, Byeongjin; Kim, Jung-Il; Park, Siwoo

    2016-01-01

    Objective The present study analyzed relationship of workplace violence and perpetrators of violence on sleep disturbance among wage workers in Korea. Methods The present study used data from the 4th Korean Working Conditions Survey (KWCS) of 2014 in selecting a total of 25,138wage workers as the study population, which excluded those who failed or refused to respond to questions required for the present study. The workplace violence experience group included people who satisfied at least one...

  7. 4th iTi Conference in Turbulence

    CERN Document Server

    Peinke, Joachim; Talamelli, Alessandro; Castillo, Luciano; Hölling, Michael

    2012-01-01

    This fourth issue on "progress in turbulence" is based on the fourth ITI conference (ITI interdisciplinary turbulence initiative), which took place in Bertinoro, North Italy. Leading researchers from the engineering and physical sciences presented latest results in turbulence research. Basic as well as applied research is driven by the rather notorious difficult and essentially unsolved problem of turbulence. In this collection of contributions clear progress can be seen in different aspects, ranging from new quality of numerical simulations to new concepts of experimental investigations and new theoretical developments. The importance of turbulence is shown for a wide range of applications including: combustion, energy, flow control, urban flows, are few examples found in this volume. A motivation was to bring fundamentals of turbulence in connection with renewable energy. This lead us to add a special topic relevant to the impact of turbulence on the wind energy conversion. The structure of the present book...

  8. Our experience of blood flow measurements using radioactive tracers

    International Nuclear Information System (INIS)

    Danet, Bernard.

    1974-01-01

    A critical study of blood flow measuring methods is proposed. After a review of the various diffusible and non-diffusible radioactive tracers and the corresponding detector systems, the principles which allow to measure blood flow from the data so obtained, are studied. There is a different principle of flow measurement for each type of tracer. The theory of flow measurement using non-diffusible tracers (human serum albumin labelled with 131 I or sup(99m)Tc, 113 In-labelled siderophiline) and its application to cardiac flow measurement are described first. Then the theory of flow measurement using diffusible tracers ( 133 Xe, 85 Kr) and its application to measurement of blood flow through tissues (muscles and kidney particularly) are described. A personal experience of this various flow measurements is reported. The results obtained, the difficulties encountered and the improvments proposed are developed [fr

  9. 77 FR 38486 - Safety Zone; City of Tonawanda July 4th Celebration, Niagara River, Tonawanda, NY

    Science.gov (United States)

    2012-06-28

    ... 1625-AA00 Safety Zone; City of Tonawanda July 4th Celebration, Niagara River, Tonawanda, NY AGENCY... safety zone on the Niagara River, Tonawanda, New York. This safety zone is intended to restrict vessels from a portion of the Niagara River during the City of Tonawanda July 4th Celebration fireworks on July...

  10. The school nutrition program's role in weight management of 4th grade elementary students

    Science.gov (United States)

    We are attempting to uncover the school nutrition program's role in weight management of 4th grade elementary students. Data was collected within a time frame for the food frequency questionnaire (FFQ) set at two months at the WT Cheney Elementary School and South Wood Elementary for 4th grade stud...

  11. 75 FR 35649 - Safety Zone; Northern California Annual Fireworks Events, July 4th Fireworks Display

    Science.gov (United States)

    2010-06-23

    ... Zone; Northern California Annual Fireworks Events, July 4th Fireworks Display AGENCY: Coast Guard, DHS... July Fireworks Display safety zone, from 9 a.m. through 10 p.m. on July 4, 2010 in position 39[deg]10... safety zone for the annual Tahoe City 4th of July Fireworks in 33 CFR 165.1191 on July 4, 2010, from 9 a...

  12. 4th Evian Workshop on LHC beam operation

    CERN Document Server

    Goddard, B; Dubourg, S

    2013-01-01

    The principle aims of the workshop are to: review and capture 2012 LHC beam operations experience; review system performance; examine the foreseen challenges and limitations of post long shutdown operations; have a look at possible running scenarios in the post long shutdown era.

  13. 4th Pediatric Allergy and Asthma Meeting (PAAM)

    OpenAIRE

    Yavuz, S. Tolga; Koc, Ozan; Gungor, Ali; Gok, Faysal; Hawley, Jessica; O?Brien, Christopher; Thomas, Matthew; Brodlie, Malcolm; Michaelis, Louise; Mota, In?s; Gaspar, ?ngela; Piedade, Susana; Sampaio, Gra?a; Dias, Jos? Geraldo; Paiva, Miguel

    2016-01-01

    Table of contents WORKSHOP 4: Challenging clinical scenarios (CS01?CS06) CS01 Bullous lesions in two children: solitary mastocytoma S. Tolga Yavuz, Ozan Koc, Ali Gungor, Faysal Gok CS02 Multi-System Allergy (MSA) of cystic fibrosis: our institutional experience Jessica Hawley, Christopher O?Brien, Matthew Thomas, Malcolm Brodlie, Louise Michaelis CS03 Cold urticaria in pediatric age: an invisible cause for severe reactions In?s Mota, ?ngela Gaspar, Susana Piedade, Gra?a Sampaio, Jos? Geraldo ...

  14. Microgravity Multi-Phase Flow Experiment for Suborbital Testing (MFEST)

    Data.gov (United States)

    National Aeronautics and Space Administration — The primary objective is to conduct a pathfinder, suborbital flight experiment for two-phase fluid flow and separator operations.The primary purpose of this test...

  15. Parametric analyses of planned flowing uranium hexafluoride critical experiments

    Science.gov (United States)

    Rodgers, R. J.; Latham, T. S.

    1976-01-01

    Analytical investigations were conducted to determine preliminary design and operating characteristics of flowing uranium hexafluoride (UF6) gaseous nuclear reactor experiments in which a hybrid core configuration comprised of UF6 gas and a region of solid fuel will be employed. The investigations are part of a planned program to perform a series of experiments of increasing performance, culminating in an approximately 5 MW fissioning uranium plasma experiment. A preliminary design is described for an argon buffer gas confined, UF6 flow loop system for future use in flowing critical experiments. Initial calculations to estimate the operating characteristics of the gaseous fissioning UF6 in a confined flow test at a pressure of 4 atm, indicate temperature increases of approximately 100 and 1000 K in the UF6 may be obtained for total test power levels of 100 kW and 1 MW for test times of 320 and 32 sec, respectively.

  16. 4th Pediatric Allergy and Asthma Meeting (PAAM)

    OpenAIRE

    Yavuz, S. Tolga; Koc, Ozan; Gungor, Ali; Gok, Faysal; Hawley, Jessica; O’Brien, Christopher; Thomas, Matthew; Brodlie, Malcolm; Michaelis, Louise; Mota, Inês; Gaspar, Ângela; Piedade, Susana; Sampaio, Graça; Dias, José Geraldo; Paiva, Miguel

    2016-01-01

    Table of contents WORKSHOP 4: Challenging clinical scenarios (CS01–CS06) CS01 Bullous lesions in two children: solitary mastocytoma S. Tolga Yavuz, Ozan Koc, Ali Gungor, Faysal Gok CS02 Multi-System Allergy (MSA) of cystic fibrosis: our institutional experience Jessica Hawley, Christopher O’Brien, Matthew Thomas, Malcolm Brodlie, Louise Michaelis CS03 Cold urticaria in pediatric age: an invisible cause for severe reactions Inês Mota, Ângela Gaspar, Susana Piedade, Graça Sampaio, José Geraldo ...

  17. Summary of 4th general plan of radioactive wastes

    International Nuclear Information System (INIS)

    Veganzones, A.

    1995-01-01

    The last 9th of December 1994 the Council of Ministries approved the Fourth General Plan of Radioactive Waste (PGRR). The Fourth Plan actualizes former texts taking into into account new circumstances, both technical and economical, affecting radioactive waste. Some of the steps that conform the global waste management process have been revised on the light of the Spanish experience but also considering the evolution and trends in other countries. In this work some of the most important aspects included in the Fourth general Plan are overviewed. (Author)

  18. Electrospun 4th-Generation Solid Dispersions of Poorly Water-Soluble Drug Utilizing Two Different Processes

    Directory of Open Access Journals (Sweden)

    Zhu Zhang

    2018-01-01

    Full Text Available Different from traditional solid dispersion (SD for improving the dissolution rates of poorly water-soluble drugs, the upgraded 4th SD was developed to furnish a drug sustained-release profile. In this work, two different kinds of 4th SDs were fabricated using two electrospinning processes. One is a ternary SD (nanofibers F2 that consisted of ethyl cellulose (EC, polyethylene glycol 1000 (PEG, and tamoxifen citrate (TAM from a modified coaxial process, and the other is a binary SD (nanofibers F1 which is comprised of EC and TAM from a single-fluid blending process. Scanning electronic microscopic observations demonstrated that F2 (330±50 nm showed a better quality than F1 (870±230 nm in terms of size and size distribution although both of them had a smooth surface morphology and a cross section. X-ray diffraction patterns verified that both SDs were amorphous nanocomposites owing to the favorable secondary interactions among these components, as suggested from the results of FTIR. In vitro dissolution experiments indicated that F2 could furnish an improved drug sustained-release characteristics compared to F1, exhausting all the contained TAM and having weaker leveling-off late release. The molecular behaviors of drug sustained-release from the binary 4th SD were suggested. The protocols reported here paved an alternative way for developing novel functional nanomaterials for effective delivery of poorly water-soluble drugs.

  19. Flow visualization of acoustic levitation experiment

    Science.gov (United States)

    Baroth, ED

    1987-01-01

    Acoustic levitation experiments for space applications were performed. Holographic interferometry is being used to study the heat transfer rates on a heated rod enclosed in a 6 cu in chamber. Acoustic waves at levels up to 150 db increased the heating rates to the rod by factors of three to four. High speed real time holographic interferometry was used to measure the boundary layer on the heated rod. Data reduction and digitization of the interferograms are being implemented.

  20. South Korea's Experience with International Capital Flows

    OpenAIRE

    Marcus Noland

    2005-01-01

    South Korea%u2019s experience is unparalleled in its combination of sustained prosperity, capital controls, and financial crisis. Over several decades, South Korea experienced rapid sustained growth in the presence of capital controls. These controls and the de-linking of domestic and international financial markets were an essential component of the country's state-led development strategy. As the country developed, opportunities for easy technological catch-up eroded, requiring more sophist...

  1. 4th International Conference on Software Process Improvement

    CERN Document Server

    Muñoz, Mirna; Rocha, Álvaro; Calvo-Manzano, Jose

    2016-01-01

    This book contains a selection of papers from The 2015 International Conference on Software Process Improvement (CIMPS’15), held between the 28th and 30th of October in Mazatlán, Sinaloa, México. The CIMPS’15 is a global forum for researchers and practitioners that present and discuss the most recent innovations, trends, results, experiences and concerns in the several perspectives of Software Engineering with clear relationship but not limited to software processes, Security in Information and Communication Technology and Big Data Field. The main topics covered are: Organizational Models, Standards and Methodologies, Knowledge Management, Software Systems, Applications and Tools, Information and Communication Technologies and Processes in non-software domains (Mining, automotive, aerospace, business, health care, manufacturing, etc.) with a demonstrated relationship to software process challenges.

  2. Operating experience using venturi flow meters at liquid helium temperature

    International Nuclear Information System (INIS)

    Wu, K.C.

    1992-01-01

    Experiences using commercial venturi to measure single phase helium flow near 4 K (degree Kelvin) for cooling superconducting magnets have been presented. The mass flow rate was calculated from the differential pressure and the helium density evaluated from measured pressure and temperature. The venturi flow meter, with a full range of 290 g/s (0.29 Kg/s) at design conditions, has been found to be reliable and accurate. The flow measurements have been used, with great success, for evaluating the performance of a cold centrifugal compressor, the thermal acoustic heat load of a cryogenic system and the cooling of a superconducting magnet after quench

  3. First TRUE Stage - Transport of solutes in an interpreted single fracture. Proceedings from the 4th international seminar

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-08-01

    . The outcome of the 4th International Aespoe seminar focused on the TRUE-1 experiments can be summarised in the following main points: There is a general consensus that the observed retardation observed in the TRUE-1 experiments requires diffusion into geological material to be an active process. This supported by the -3/2 slope noted in log-log BTCs. Whether this is due to diffusion (and subsequent sorption) in the altered matrix rock, or in possible fault gouge cannot be differentiated with available data; Some researchers claim that the observed enhanced retardation may be explained by diffusion into stagnant water pools, pure surface sorption, or may be due to an underestimation in the flow-wetted surface area. The latter effect may be attributed to a more complex flow path (multi-layered structure) or three-dimensional effects; A clear differentiation between the principal active process can only assessed by resin injection and subsequent excavation and analysis; It was identified that experiments of TRUE type are important for improving the understanding of retention processes. However, this type of experiment will not be part of a site characterisation programme; It was recommended to broaden the data base from the TRUE-1 site before characterising pore space with resin techniques. This includes tracer dilution tests using sinks in other features than Feature A. The seminar was divided into four sessions: 1. Detailed characterisation of transport-related properties (Three contributions separately indexed). 2. Alternative evaluation of TRUE-1 results (Five contributions separately indexed). 3. Related studies (Three contributions separately indexed). 4. Understanding of retention processes in a single fracture (Two contributions separately indexed)

  4. Fracture/matrix flow experiments results

    International Nuclear Information System (INIS)

    Constantino, M S; Wildenschild, D; Roberts, J J; Kneafsey, T J; Lin, W

    1998-01-01

    The impact of vapor diffusion and its potential enhancement are of concern with respect to the performance of the potential nuclear waste repository at Yucca Mountain. Under non-isothermal conditions, such as those prevailing in the near-field environment, gas-phase diffusion of water vapor (a condensable component) may be enhanced as compared to isothermal conditions. Two main phenomena are responsible for this enhancement (Philip and DeVries 1957, p. 226). Normally, diffusive transport of water vapor is obstructed by the presence of liquid islands in the pore throats, and diffusion is reduced at higher saturations. However, under a thermal gradient, a vapor-pressure gradient develops in the gas phase, causing water to evaporate from one side of the liquid island and to diffuse in the gas phase to a liquid island of lower temperature, where it condenses (Figure 1). Water flows through the liquid island as a result of differences in meniscus curvature between the two sides. This difference is caused by the temperature gradient between the liquid-vapor interfaces on the two ends of the liquid island. The evaporation-condensation process repeats itself on the other side of the liquid island; the result is an enhanced diffusive flux through the medium

  5. TID Test Results for 4th Generation iPad(TradeMark)

    Science.gov (United States)

    Guertin, S. M.; Allen, G. R.; McClure, S. S.; LaBel, K. A.

    2013-01-01

    TID testing of 4th generation iPads is reported. Of iPad subsystems, results indicate that the charging circuitry and display drivers fail at lowest TID levels. Details of construction are investigated for additional testing of components.

  6. Report of the 4th Workshop for Technology Transfer for Intelligent Compaction Consortium.

    Science.gov (United States)

    2016-03-01

    On October 2728, 2015, the Kentucky Transportation Cabinet (KYTC) hosted the 4th workshop for : the Technology Transfer for Intelligent Compaction Consortium (TTICC), a Transportation Pooled Fund : (TPF5(233)) initiative designed to identify, s...

  7. Flow Experience in Design Thinking and Practical Synergies with Lego Serious Play

    Science.gov (United States)

    Primus, Dirk J.; Sonnenburg, Stephan

    2018-01-01

    The flow experience can be an important precursor to high levels of creativity and innovation. Prior work has identified and conceptualized the key elements of the flow experience in cocreative activities as individual flow corridor, individual flow feeling, and group flow. Surprisingly, the flow experience is underrepresented in theory and…

  8. Painting of fourth and chromosome-wide regulation of the 4th chromosome in Drosophila melanogaster.

    Science.gov (United States)

    Johansson, Anna-Mia; Stenberg, Per; Bernhardsson, Carolina; Larsson, Jan

    2007-05-02

    Drosophila melanogaster exhibits two expression-regulating systems that target whole, specific chromosomes: the dosage compensation system whereby the male-specific lethal complex doubles transcription of genes on the male X-chromosome and the chromosome 4-specific protein Painting of fourth, POF. POF is the first example of an autosome-specific protein and its presence raises the question of the universality of chromosome-specific regulation. Here we show that POF and heterochromatin protein 1 (HP1) are involved in the global regulation of the 4th chromosome. Contrary to previous conclusions, Pof is not essential for survival of diplo-4th karyotype flies. However, Pof is essential for survival of haplo-4th individuals and expression of chromosome 4 genes in diplo-4th individuals is decreased in the absence of Pof. Mapping of POF using chromatin immunoprecipitation suggested that it binds within genes. Furthermore, we show that POF binding is dependent on heterochromatin and that POF and HP1 bind interdependently to the 4th chromosome. We propose a balancing mechanism involving POF and HP1 that provides a feedback system for fine-tuning expression status of genes on the 4th chromosome.

  9. Flow experience in teams: The role of shared leadership.

    Science.gov (United States)

    Aubé, Caroline; Rousseau, Vincent; Brunelle, Eric

    2018-04-01

    The present study tests a multilevel mediation model concerning the effect of shared leadership on team members' flow experience. Specifically, we investigate the mediating role of teamwork behaviors in the relationships between 2 complementary indicators of shared leadership (i.e., density and centralization) and flow. Based on a multisource approach, we collected data through observation and survey of 111 project teams (521 individuals) made up of university students participating in a project management simulation. The results show that density and centralization have both an additive effect and an interaction effect on teamwork behaviors, such that the relationship between density and teamwork behaviors is stronger when centralization is low. In addition, teamwork behaviors play a mediating role in the relationship between shared leadership and flow. Overall, the findings highlight the importance of promoting team-based shared leadership in organizations to favor the flow experience. (PsycINFO Database Record (c) 2018 APA, all rights reserved).

  10. The Prevention Disaster Program of Flood in 2013 for the 4th Grade Students of Kawatanaka Primary School, Tokushima Prefecture, Japan and Underflow Channels Revealed in 2016

    Science.gov (United States)

    Kawamata, Sanae; Murata, Mamoru

    2017-12-01

    The Typhoon No. 18 caused flood on September 15, 2013 in the Kawata River basin, Yoshinogawa City, Tokushima Prefecture. The Kawata River is a raised river bed of 36.7 m with banks to 40.5 m above sea level. The heavy rain did not destroy the banks but made the river level 39.4 m high and then pressed the underflow channel. As the Kawatanaka primary school is located at 36.2 m height, it was not submerged although the underflow channel overbanked the adjacent playground. An educational program on the prevention and reduction for natural disaster, which consists of science, social studies and presentation, was conducted to 18 students of the 4th grade in the period of integrated study in the Kawatanaka primary school from September 17, 2013. On the first day, flow current markings from 625 holes, 30 cm to 1 mm in diameter, on the playground were observed. The flow currents showed direction from SE to NW. On the basis of their observations on the flow currents that water runs from high to low, the students considered the phenomena as a result of tilting of the ground. They conducted activity as their homework to confirm their hypothesis to know if there is any tilt in the ground. They took plastic bottle filled with water and reviled that the ground had 1 to 2 degrees’ tilt to the NW during the experiment. On the bases of the difference between E to W flow of the Kawata River and their SE to NW estimated current flow on the playground and the fact that the bank of the river was not destroyed, the students suggested that the heavy rain had pressed the underflow channels. The suggested channels were found on the playground, where new school buildings were constructed in 2016, by one of the students who studied the program in 2013.

  11. Modeling of Synergy Between 4th and 6th Harmonic Absorptions of Fast Waves on Injected Beams in DIII-D Tokamak

    International Nuclear Information System (INIS)

    Choi, M.; Pinsker, R. I.; Chan, V. S.; Muscatello, C. M.; Jaeger, E. F.

    2011-01-01

    In recent moderate to high harmonic fast wave heating and current drive experiments in DIII-D, a synergy effect was observed when the 6 th harmonic 90 MHz fast wave power is applied to the plasma preheated by neutral beams and the 4 th harmonic 60 MHz fast wave. In this paper, we investigate how the synergy can occur using ORBIT-RF coupled with AORSA. Preliminary simulations suggest that damping of 4 th harmonic FW on beam ions accelerates them above the injection energy, which may allow significant damping of 6 th harmonic FW on beam ion tails to produce synergy.

  12. Microrelief-Controlled Overland Flow Generation: Laboratory and Field Experiments

    Directory of Open Access Journals (Sweden)

    Xuefeng Chu

    2015-01-01

    Full Text Available Surface microrelief affects overland flow generation and the related hydrologic processes. However, such influences vary depending on other factors such as rainfall characteristics, soil properties, and initial soil moisture conditions. Thus, in-depth research is needed to better understand and evaluate the combined effects of these factors on overland flow dynamics. The objective of this experimental study was to examine how surface microrelief, in conjunction with the factors of rainfall, soil, and initial moisture conditions, impacts overland flow generation and runoff processes in both laboratory and field settings. A series of overland flow experiments were conducted for rough and smooth surfaces that represented distinct microtopographic characteristics and the experimental data were analyzed and compared. Across different soil types and initial moisture conditions, both laboratory and field experiments demonstrated that a rough soil surface experienced a delayed initiation of runoff and featured a stepwise threshold flow pattern due to the microrelief-controlled puddle filling-spilling-merging dynamics. It was found from the field experiments that a smooth plot surface was more responsive to rainfall variations especially during an initial rainfall event. However, enhanced capability of overland flow generation and faster puddle connectivity of a rough field plot occurred during the subsequent rain events.

  13. Book of abstracts: 3rd International Conference on Smart Energy Systems and 4th Generation District Heating

    DEFF Research Database (Denmark)

    This year the conference is organised by two research centres/projects in collaboration with Aalborg University. The first is the 4DH Strategic Research Centre and the other is the project RE-INVEST, both supported financial by the Danish Innovation Fund. After the previous two year´s success...... everyone for your valuable contributions. The aim is to present and discuss scientific findings and industrial experiences related to the development of Smart Energy Systems and future 4th Generation District Heating Technologies and Systems (4GDH). This development is fundamental to the implementation...

  14. Analogue experiments as benchmarks for models of lava flow emplacement

    Science.gov (United States)

    Garel, F.; Kaminski, E. C.; Tait, S.; Limare, A.

    2013-12-01

    During an effusive volcanic eruption, the crisis management is mainly based on the prediction of lava flow advance and its velocity. The spreading of a lava flow, seen as a gravity current, depends on its "effective rheology" and on the effusion rate. Fast-computing models have arisen in the past decade in order to predict in near real time lava flow path and rate of advance. This type of model, crucial to mitigate volcanic hazards and organize potential evacuation, has been mainly compared a posteriori to real cases of emplaced lava flows. The input parameters of such simulations applied to natural eruptions, especially effusion rate and topography, are often not known precisely, and are difficult to evaluate after the eruption. It is therefore not straightforward to identify the causes of discrepancies between model outputs and observed lava emplacement, whereas the comparison of models with controlled laboratory experiments appears easier. The challenge for numerical simulations of lava flow emplacement is to model the simultaneous advance and thermal structure of viscous lava flows. To provide original constraints later to be used in benchmark numerical simulations, we have performed lab-scale experiments investigating the cooling of isoviscous gravity currents. The simplest experimental set-up is as follows: silicone oil, whose viscosity, around 5 Pa.s, varies less than a factor of 2 in the temperature range studied, is injected from a point source onto a horizontal plate and spreads axisymmetrically. The oil is injected hot, and progressively cools down to ambient temperature away from the source. Once the flow is developed, it presents a stationary radial thermal structure whose characteristics depend on the input flow rate. In addition to the experimental observations, we have developed in Garel et al., JGR, 2012 a theoretical model confirming the relationship between supply rate, flow advance and stationary surface thermal structure. We also provide

  15. Neural contributions to flow experience during video game playing.

    Science.gov (United States)

    Klasen, Martin; Weber, René; Kircher, Tilo T J; Mathiak, Krystyna A; Mathiak, Klaus

    2012-04-01

    Video games are an exciting part of new media. Although game play has been intensively studied, the underlying neurobiology is still poorly understood. Flow theory is a well-established model developed to describe subjective game experience. In 13 healthy male subjects, we acquired fMRI data during free play of a video game and analyzed brain activity based on the game content. In accordance with flow theory, we extracted the following factors from the game content: (i) balance between ability and challenge; (ii) concentration and focus; (iii) direct feedback of action results; (iv) clear goals; and (v) control over the situation/activity. We suggest that flow is characterized by specific neural activation patterns and that the latter can be assessed-at least partially-by content factors contributing to the emergence of flow. Each of the content factors was characterized by specific and distinguishable brain activation patterns, encompassing reward-related midbrain structures, as well as cognitive and sensorimotor networks. The activation of sensory and motor networks in the conjunction analyses underpinned the central role of simulation for flow experience. Flow factors can be validated with functional brain imaging which can improve the understanding of human emotions and motivational processes during media entertainment.

  16. Effectiveness of oxfendazole against early and later 4th-stage Strongylus vulgaris in ponies.

    Science.gov (United States)

    Slocombe, J O; McCraw, B M; Pennock, P; Ducharme, N G; Baird, J D

    1986-03-01

    Twenty pony foals (reared worm free), 6.5 to 10 weeks of age, were inoculated with Strongylus vulgaris and allocated to 5 groups, each with 4 foals. One week after inoculation, 1 group of 4 foals was given oxfendazole (OFZ) at a dosage rate of 10 mg/kg of body weight, another group was given 2 such treatments 48 hours apart, and a 3rd group was given a placebo. All treatments were administered by stomach tube. Three weeks later, foals were euthanatized and necropsied in a test for efficacy against early 4th-stage larvae. Oxfendazole was 80% and 94.9% effective against early 4th-stage S vulgaris with 1 and 2 doses, respectively. A 4th group of 4 foals was given 2 treatments of OFZ, 48 hours apart, about 8 weeks after inoculation, and a 5th group was given a placebo. These foals were euthanatized and necropsied 5 weeks after treatment in a test for efficacy against later 4th-stage larvae. Two doses of OFZ were 96.6% effective against later 4th-stage larvae.

  17. Charactering baseline shift with 4th polynomial function for portable biomedical near-infrared spectroscopy device

    Science.gov (United States)

    Zhao, Ke; Ji, Yaoyao; Pan, Boan; Li, Ting

    2018-02-01

    The continuous-wave Near-infrared spectroscopy (NIRS) devices have been highlighted for its clinical and health care applications in noninvasive hemodynamic measurements. The baseline shift of the deviation measurement attracts lots of attentions for its clinical importance. Nonetheless current published methods have low reliability or high variability. In this study, we found a perfect polynomial fitting function for baseline removal, using NIRS. Unlike previous studies on baseline correction for near-infrared spectroscopy evaluation of non-hemodynamic particles, we focused on baseline fitting and corresponding correction method for NIRS and found that the polynomial fitting function at 4th order is greater than the function at 2nd order reported in previous research. Through experimental tests of hemodynamic parameters of the solid phantom, we compared the fitting effect between the 4th order polynomial and the 2nd order polynomial, by recording and analyzing the R values and the SSE (the sum of squares due to error) values. The R values of the 4th order polynomial function fitting are all higher than 0.99, which are significantly higher than the corresponding ones of 2nd order, while the SSE values of the 4th order are significantly smaller than the corresponding ones of the 2nd order. By using the high-reliable and low-variable 4th order polynomial fitting function, we are able to remove the baseline online to obtain more accurate NIRS measurements.

  18. Heterogeneity of water flow in grassland soil during irrigation experiment

    Czech Academy of Sciences Publication Activity Database

    Lichner, Ľ.; Dušek, J.; Tesař, Miroslav; Czachor, H.; Mészároš, I.

    2014-01-01

    Roč. 69, č. 11 (2014), s. 1555-1561 ISSN 0006-3088 R&D Projects: GA TA ČR(CZ) TA0201451 Grant - others:ERDF ITMS26240120004 Institutional support: RVO:67985874 Keywords : degree of preferential flow * effective cross section * infiltration experiment * radioactive tracer technique * sandy soil Subject RIV: DA - Hydrology ; Limnology Impact factor: 0.827, year: 2014

  19. Flow Genres: The Varieties of Video Game Experience

    Czech Academy of Sciences Publication Activity Database

    Hrabec, O.; Chrz, Vladimír

    2015-01-01

    Roč. 7, č. 1 (2015), s. 1-19 ISSN 1942-3888 R&D Projects: GA ČR(CZ) GAP407/12/2432 Institutional support: RVO:68081740 Keywords : flow * optimal experience * genre * video game Subject RIV: AN - Psychology

  20. Water flow experiments and analyses on the cross-flow type mercury target model with the flow guide plates

    CERN Document Server

    Haga, K; Kaminaga, M; Hino, R

    2001-01-01

    A mercury target is used in the spallation neutron source driven by a high-intensity proton accelerator. In this study, the effectiveness of the cross-flow type mercury target structure was evaluated experimentally and analytically. Prior to the experiment, the mercury flow field and the temperature distribution in the target container were analyzed assuming a proton beam energy and power of 1.5 GeV and 5 MW, respectively, and the feasibility of the cross-flow type target was evaluated. Then the average water flow velocity field in the target mock-up model, which was fabricated from Plexiglass for a water experiment, was measured at room temperature using the PIV technique. Water flow analyses were conducted and the analytical results were compared with the experimental results. The experimental results showed that the cross-flow could be realized in most of the proton beam path area and the analytical result of the water flow velocity field showed good correspondence to the experimental results in the case w...

  1. Aerospace Thematic Workshop (4th): Fundamentals of Aerodynamic Flow and Combustion Control by Plasmas

    Science.gov (United States)

    2013-04-01

    Examples of this effect are often called diesel ignition enhancers such as ethyl-hexyl nitrate, but they can also be relatively unstable species...requirements and calibration techniques are discussed. The field sensitivity of the laser spectroscopic technique depends on the molecular and the...that grows until transitioning to a turbulent flame; this turbulent flame in a second stage propagates upstream towards the injector nozzle to

  2. Circulation system for flowing uranium hexafluoride cavity reactor experiments

    International Nuclear Information System (INIS)

    Jaminet, J.F.; Kendall, J.S.

    1976-01-01

    Accomplishment of the UF 6 critical cavity experiments, currently in progress, and planned confined flowing UF 6 initial experiments requires development of reliable techniques for handling heated UF 6 throughout extended ranges of temperature, pressure, and flow rate. The development of three laboratory-scale flow systems for handling gaseous UF 6 at temperatures up to 500 K, pressures up to approximately 40 atm, and continuous flow rates up to approximately 50 g/s is presented. A UF 6 handling system fabricated for static critical tests currently being conducted at Los Alamos Scientific Laboratory (LASL) is described. The system was designed to supply UF 6 to a double-walled aluminum core canister assembly at temperatures between 300 K and 400 K and pressures up to 4 atm. A second UF 6 handling system designed to provide a circulating flow of up to 50 g/s of gaseous UF 6 in a closed-loop through a double-walled aluminum core canister with controlled temperature and pressure is described

  3. Groundwater flow through a natural fracture. Flow experiments and numerical modelling

    Energy Technology Data Exchange (ETDEWEB)

    Larsson, Erik [Chalmers Univ. of Technology, Goeteborg (Sweden). Dept of Geology

    1997-09-01

    Groundwater flow and transport play an important role not only for groundwater exploration but also in environmental engineering problems. This report considers how the hydraulic properties of fractures in crystalline rock depend on the fracture aperture geometry. Different numerical models are discussed and a FDM computer code for two- and three- dimensional flow-modelling has been developed. Different relations between the cells in the model are tested and compared with results in the literature. A laboratory experimental work has been done to carry out flow experiments and aperture measurements on the same specimen of a natural fracture. The drilled core sample had fractures parallel to the core axis and was placed inside a biaxial cell during the experiments. The water pressure gradient and the compression stress were varied during the experiments and also a tracer test was done. After the flow experiments, the aperture distribution for a certain compression was measured by injecting an epoxy resin into the fracture. The thickness of the resin layer was then studied in saw cut sections of the sample. The results from the experiments were used to validate numerical and analytical models, based on aperture distribution, for flow and transport simulations. In the disturbed zone around a drift both water and air are present in the fractures. The gas will go to the most wide part of the fracture because the capillarity and the conductivity decrease. The dependence of the effective conductivity on the variance of the conductivity and the effect of extinction of highly conductive cells has also been studied. A discussion of how gas in fractures around a drift can cause a skin effect is modelled and an example is given of what a saturation depending on the magnitude of the flow causes. 25 refs, 17 tabs, 43 figs.

  4. Groundwater flow through a natural fracture. Flow experiments and numerical modelling

    International Nuclear Information System (INIS)

    Larsson, Erik

    1997-09-01

    Groundwater flow and transport play an important role not only for groundwater exploration but also in environmental engineering problems. This report considers how the hydraulic properties of fractures in crystalline rock depend on the fracture aperture geometry. Different numerical models are discussed and a FDM computer code for two- and three- dimensional flow-modelling has been developed. Different relations between the cells in the model are tested and compared with results in the literature. A laboratory experimental work has been done to carry out flow experiments and aperture measurements on the same specimen of a natural fracture. The drilled core sample had fractures parallel to the core axis and was placed inside a biaxial cell during the experiments. The water pressure gradient and the compression stress were varied during the experiments and also a tracer test was done. After the flow experiments, the aperture distribution for a certain compression was measured by injecting an epoxy resin into the fracture. The thickness of the resin layer was then studied in saw cut sections of the sample. The results from the experiments were used to validate numerical and analytical models, based on aperture distribution, for flow and transport simulations. In the disturbed zone around a drift both water and air are present in the fractures. The gas will go to the most wide part of the fracture because the capillarity and the conductivity decrease. The dependence of the effective conductivity on the variance of the conductivity and the effect of extinction of highly conductive cells has also been studied. A discussion of how gas in fractures around a drift can cause a skin effect is modelled and an example is given of what a saturation depending on the magnitude of the flow causes

  5. Granular flow in a rotating drum: Experiments and theory

    Science.gov (United States)

    Hung, C. Y.; Stark, C. P.; Capart, H.; Li, L.; Smith, B.; Grinspun, E.

    2015-12-01

    Erosion at the base of a debris flow fundamentally controls how large the flow will become and how far it will travel. Experimental observations of this important phenomenon are rather limited, and this lack has led theoretical treatments to making ad hoc assumptions about the basal process. In light of this, we carried out a combination of laboratory experiments and theoretical analysis of granular flow in a rotating drum, a canonical example of steady grain motion in which entrainment rates can be precisely controlled. Our main result is that basal sediment is entrained as the velocity profile adjusts to imbalance in the flow of kinetic energy.Our experimental apparatus consisted of a 40cm-diameter drum, 4cm-deep, half-filled with 2.3mm grains. Rotation rates varied from 1-70 rpm. We varied the effective scale by varying effective gravity from 1g to 70g on a geotechnical centrifuge. The field of grain motion was recorded using high-speed video and mapped using particle tracking velocimetry. In tandem we developed a depth-averaged theory using balance equations for mass, momentum and kinetic energy. We assumed a linearized GDR Midi granular rheology [da Cruz, 2005] and a Coulomb friction law along the sidewalls [Jop et al., 2005]. A scaling analysis of our equations yields a dimensionless "entrainment number" En, which neatly parametrizes the flow geometry in the drum for a wide range of variables, e.g., rotation rate and effective gravity. At low En, the flow profile is planar and kinetic energy is balanced locally in the flow layer. At high En, the flow profile is sigmoidal (yin-yang shaped) and the kinetic energy is dominated by longitudinal, streamwise transfer. We observe different scaling behavior under each of these flow regimes, e.g., between En and kinetic energy, surface slope and flow depth. Our theory correctly predicts their scaling exponents and the value of En at which the regime transition takes place. We are also able to make corrections for

  6. Scaling up debris-flow experiments on a centrifuge

    Science.gov (United States)

    Hung, C.; Capart, H.; Crone, T. J.; Grinspum, E.; Hsu, L.; Kaufman, D.; Li, L.; Ling, H.; Reitz, M. D.; Smith, B.; Stark, C. P.

    2013-12-01

    Boundary forces generated by debris flows can be powerful enough to erode bedrock and cause considerable damage to infrastructure during runout. Formulation of an erosion-rate law for debris flows is therefore a high priority, and it makes sense to build such a law around laboratory experiments. However, running experiments big enough to generate realistic boundary forces is a logistical challenge to say the least [1]. One alternative is to run table-top simulations with unnaturally weak but fast-eroding pseudo-bedrock, another is to extrapolate from micro-erosion of natural substrates driven by unnaturally weak impacts; hybrid-scale experiments have also been conducted [2]. Here we take a different approach in which we scale up granular impact forces by running our experiments under enhanced gravity in a geotechnical centrifuge [3]. Using a 40cm-diameter rotating drum [2] spun at up to 100g, we generate debris flows with an effective depth of over several meters. By varying effective gravity from 1g to 100g we explore the scaling of granular flow forces and the consequent bed and wall erosion rates. The velocity and density structure of these granular flows is monitored using laser sheets, high-speed video, and particle tracking [4], and the progressive erosion of the boundary surfaces is measured by laser scanning. The force structures and their fluctuations within the granular mass and at the boundaries are explored with contact dynamics numerical simulations that mimic the lab experimental conditions [5]. In this presentation we summarize these results and discuss how they can contribute to the formulation of debris-flow erosion law. [1] Major, J. J. (1997), Journal of Geology 105: 345-366, doi:10.1086/515930 [2] Hsu, L. (2010), Ph.D. thesis, University of California, Berkeley [3] Brucks, A., et al (2007), Physical Review E 75, 032301, doi:10.1103/PhysRevE.75.032301 [4] Spinewine, B., et al (2011), Experiments in Fluids 50: 1507-1525, doi: 10.1007/s00348

  7. Supercritical water natural circulation flow stability experiment research

    Energy Technology Data Exchange (ETDEWEB)

    Ma, Dongliang; Zhou, Tao; Li, Bing [North China Electric Power Univ., Beijing (China). School of Nuclear Science and Engineering; North China Electric Power Univ., Beijing (China). Inst. of Nuclear Thermalhydraulic Safety and Standardization; North China Electric Power Univ., Beijing (China). Beijing Key Lab. of Passive Safety Technology for Nuclear Energy; Huang, Yanping [Nuclear Power Institute of China, Chengdu (China). Science and Technology on Reactor System Design Technology Lab.

    2017-12-15

    The Thermal hydraulic characteristics of supercritical water natural circulation plays an important role in the safety of the Generation-IV supercritical water-cooled reactors. Hence it is crucial to conduct the natural circulation heat transfer experiment of supercritical water. The heat transfer characteristics have been studied under different system pressures in the natural circulation systems. Results show that the fluctuations in the subcritical flow rate (for natural circulation) is relatively small, as compared to the supercritical flow rate. By increasing the heating power, it is observed that the amplitude (and time period) of the fluctuation tends to become larger for the natural circulation of supercritical water. This tends to show the presence of flow instability in the supercritical water. It is possible to observe the flow instability phenomenon when the system pressure is suddenly reduced from the supercritical pressure state to the subcritical state. At the test outlet section, the temperature is prone to increase suddenly, whereas the blocking effect may be observed in the inlet section of the experiment.

  8. Effectiveness of Web Quest in Enhancing 4th Grade Students' Spiritual Intelligence

    Science.gov (United States)

    Jwaifell, Mustafa; Al-Mouhtadi, Reham; Aldarabah, Intisar

    2015-01-01

    Spiritual intelligence has gained great interest from a good number of the researchers and scholars, while there is a lack of using new technologies such as WebQuest as an instructional tool; which is one of the e-learning applications in education in enhancing spiritual intelligence of 4th graders in Jordanian schools. This study aimed at…

  9. Search for extra dimensions, leptoquarks, 4th generation and ttbar resonances

    CERN Document Server

    AUTHOR|(CDS)2072072

    2013-01-01

    The searches for extra-dimensions, top resonances, 4th generation quarks and leptoquark signatures are presented. The results are based on proton-proton collision data at sqrt(s) = 7 or 8 TeV, corresponding to various integrated luminosities. No signal of physics beyond the Standard Model has been observed so far.

  10. Fuels. Deliveries and consumption of fuels during 4th quarter 2002 and year 2002

    International Nuclear Information System (INIS)

    2003-01-01

    The total volume of oil product deliveries (excluded lubricants, bitumen etc.) from the oil companies was 1 per cent lower during 2002 compared with 2001. The deliveries of motor gasoline and diesel oil increased by 2 and 5 per cent. Domestic heating oil and heavy fuel oils decreased by 3 and 5 per cent compared with 2001. Under the 4th quarter 2002 the deliveries of oil products (excluded lubricants, bitumen etc.) was 10 per cent higher compared with the same quarter 2001. The deliveries of domestic heating oil and heavy fuel oils increased by 22 per cent in each case. Motor gasoline was unchanged while the deliveries of diesel oil increased by 7 per cent. The consumption of fuels in mining and manufacturing increased by 3 % during the year 2002. The consumption of hard coal and coke increased by 5 % and the rest of the fossil fuels by 7 %. Renewable fuels decreased by 1 %. During the 4th quarter 2002 increased the fuel consumption in industry by 2 % compared with same quarter 2001. Renewable fuels decreased by 7 % while fossil fuels increased by 18 %. The consumption of fuels in electricity, gas and district heating services increased by 12 % during 2002. The consumption of oils increased by 16 %. During year 2002 the renewable fuels accounts for 68 % of the final consumption. During the 4th quarter the consumption of fuels was almost twice as high as the consumption during the 4th quarter 2001

  11. Project Management and sustainability - review of the 4th IPMA Research Conference 2016

    Directory of Open Access Journals (Sweden)

    Helgi Thor Ingason

    2017-06-01

    Full Text Available The 4th IPMA research conference was held on Project Management and Sustainability in Reykjavik, Iceland from September 14th - 16th 2016. In this article, we give a general outline of the structure of the conference, the main findings and what they mean for the project management community.

  12. 4th openlab Board of Sponsors Meeting takes place at CERN on July 6, 2005

    CERN Multimedia

    Patrice Loïez

    2005-01-01

    The 4th openlab Board of Sponsors Meeting is taking place at CERN, room 513, 1-024, the 6th July 2005. The meeting will open with an Executive Session in the presence of Dr. Robert Aymar, Director General of CERN

  13. 77 FR 56208 - Filing Dates for the Kentucky Special Election in the 4th Congressional District

    Science.gov (United States)

    2012-09-12

    ... 4th Congressional District AGENCY: Federal Election Commission. ACTION: Notice of filing dates for special election. SUMMARY: Kentucky has scheduled a general election on November 6, 2012, to fill the U.S... required to file reports in connection with the Special General Election on November 6, 2012, shall file a...

  14. 33 CFR 165.166 - Safety Zone: Macy's July 4th Fireworks, East River, NY.

    Science.gov (United States)

    2010-07-01

    ... Fireworks, East River, NY. 165.166 Section 165.166 Navigation and Navigable Waters COAST GUARD, DEPARTMENT... § 165.166 Safety Zone: Macy's July 4th Fireworks, East River, NY. (a) Regulated area. The following area...) in length, carrying persons for the purpose of viewing the fireworks, may take position in an area...

  15. Restoration of the Apollo Heat Flow Experiments Metadata

    Science.gov (United States)

    Nagihara, S.; Stephens, M. K.; Taylor, P. T.; Williams, D. R.; Hills, H. K.; Nakamura, Y.

    2015-01-01

    Geothermal heat flow probes were deployed on the Apollo 15 and 17 missions as part of the Apollo Lunar Surface Experiments Package (ALSEP). At each landing site, the astronauts drilled 2 holes, 10-m apart, and installed a probe in each. The holes were 1- and 1.5-m deep at the Apollo 15 site and 2.5-m deep at the Apollo 17 sites. The probes monitored surface temperature and subsurface temperatures at different depths. At the Apollo 15 site, the monitoring continued from July 1971 to January 1977. At the Apollo 17 site, it did from December 1972 to September 1977. Based on the observations made through December 1974, Marcus Langseth, the principal investigator of the heat flow experiments (HFE), determined the thermal conductivity of the lunar regolith by mathematically modeling how the seasonal temperature fluctuation propagated down through the regolith. He also determined the temperature unaffected by diurnal and seasonal thermal waves of the regolith at different depths, which yielded the geothermal gradient. By multiplying the thermal gradient and the thermal conductivity, Langseth obtained the endogenic heat flow of the Moon as 21 mW/m(exp 2) at Site 15 and 16 mW/m(exp 2) at Site 17.

  16. Relationships between flow experience, IKIGAI, and sense of coherence in Tai chi practitioners.

    Science.gov (United States)

    Iida, Kenji; Oguma, Yuko

    2013-01-01

    The purpose of this study was to examine the mental health effects of Tai chi on regular practitioners by investigating the relationships between flow experience, IKIGAI (Japanese: "Life worth living"), and sense of coherence. The results indicated that flow experience may influence IKIGAI and IKIGAI may influence sense of coherence; this suggests that IKIGAI may act as an intermediary between flow experience and sense of coherence. The results also indicated that the longer the Tai chi experience, the higher was the flow experience.

  17. The role of flow experience in cyber-game addiction.

    Science.gov (United States)

    Chou, Ting-Jui; Ting, Chih-Chen

    2003-12-01

    Consumer habit, an important key to repetitive consumption, is an interesting yet puzzling phenomenon. Sometimes this consumption becomes obsessive--consumers will continue to act a certain way even when they feel it is not in their best interests. However, not all consumers develop such addictions. This study uses cyber-game addiction syndrome as an analogue to trace the possible causes of consumer addiction. Results from structure equation modeling show that repetition of favorite activities has a moderate effect upon addiction, which is in line with the assertion of rational addiction theory. However, flow experience--the emotional state embracing perceptional distortion and enjoyment--shows a much stronger impact on addiction. This suggests that consumers who have experienced flow are more likely to be addicted.

  18. PREFACE: 4th Global Conference on Materials Science and Engineering (CMSE 2015)

    Science.gov (United States)

    Ruda, H. E.; Khotsianovsky, A.

    2015-12-01

    IOP Conference Series: Materials Science and Engineering is publishing a volume of conference proceedings that contains a selection of papers presented at the 4th Global Conference on Materials Science and Engineering (CMSE 2015), which is an annual event that started in 2012. CMSE 2015, technically supported by the Institute of Applied Physics and Materials Engineering of University of Macau, organized by Wuhan Advance Materials Society, was successfully held at the University of Macau-new campus located on Hengqin Island from August 3rd-6th, 2015. It aims to bring together leading academic scientists, researchers and scholars to exchange and share their experience and research results on all aspects of Materials Science and Engineering, and to discuss the practical challenges encountered and the solutions adopted. Macau, one of the two special administrative regions of the People's Republic of China, where East meets West, turned out to be an ideal meeting place for domestic and overseas participants of this annual international conference. The conference program included keynote presentations, special sessions, oral and poster contributions. From several hundred submissions, 52 of the most promising and mainstream, IOP-relevant, contributions were included in this volume. The submissions present original ideas or results of general significance, supported by clear reasoning, compelling evidence and methods, theories and practices relevant to the research. The authors state clearly the problems and the significance of their research to theory and practice. Being a successful conference, this event gathered more than 200 qualified and high-level researchers and experts from over 40 countries, including 10 keynote speakers from 6 countries, which created a good platform for worldwide researchers and engineers to enjoy the academic communication. Taking advantage of this opportunity, we would like to thank all participants of this conference, and particularly the

  19. Effects of Public Preschool Expenditures on the Test Scores of 4th Graders: Evidence from TIMSS

    Science.gov (United States)

    Waldfogel, Jane; Zhai, Fuhua

    2011-01-01

    This study examines the effects of public preschool expenditures on the math and science scores of 4th graders, holding constant child, family, and school characteristics, other relevant social expenditures, and country and year effects, in seven Organization for Economic Co-operation and Development (OECD) countries -- Australia, Japan, Netherlands, New Zealand, Norway, U.K., and U.S -- using data from the 1995 and 2003 Trends in International Mathematics and Science Study (TIMSS). Our results indicate that there are small but significant positive effects of public preschool expenditures on the math and science scores of 4th graders and preschool expenditures reduce the risk of children scoring at the low level of proficiency. We also find some evidence that children from low-resource homes and homes where the test language is not always spoken may tend to gain more from increased public preschool expenditures than other children,. PMID:21442008

  20. 4th Stage Transvaginal omental herniation during VBAC complicated by shoulder dystocia: a unique presentation of uterine rupture

    Science.gov (United States)

    2013-01-01

    Background Uterine rupture is a common complication in women attempting their first virginal birth after caesarean section (VBAC) but the risk diminishes with subsequent VBACs. It occurs in rates of 0.5-9% and is influenced by various factors. Case presentation A unique case of uterine rupture in a Kenyan woman of African descent during a repeat VBAC complicated by shoulder dystocia was discovered during the 4th stage of labour when omentum was noted protruding through the vagina. She had delivered 4 years earlier by caesarean section. Conclusion It is not common to experience uterine rupture among women attempting repeat VBAC. When it occurs, it may not always follow the known pattern intra-partum and is often associated with poor foetal outcome. PMID:23521920

  1. Enabling Manufacturing Competitiveness and Economic Sustainability : Proceedings of the 4th International Conference on Changeable, Agile, Reconfigurable and Virtual production

    CERN Document Server

    2012-01-01

    The changing manufacturing environment requires more responsive and adaptable manufacturing systems. The theme of the 4th International Conference on Changeable, Agile, Reconfigurable and Virtual production (CARV2011) is “Enabling Manufacturing Competitiveness and Economic Sustainability”. Leading edge research and best implementation practices and experiences, which address these important issues and challenges, are presented. The proceedings include advances in manufacturing systems design, planning, evaluation, control and evolving paradigms such as mass customization, personalization, changeability, re-configurability and flexibility. New and important concepts such as the dynamic product families and platforms, co-evolution of products and systems, and methods for enhancing manufacturing systems’ economic sustainability and prolonging their life to produce more than one product generation are treated. Enablers of change in manufacturing systems, production volume and capability scalability and man...

  2. Mathematics Anxiety Among 4th And 5th Grade Turkish Elementary School Students

    OpenAIRE

    Fulya Yüksel-Şahin

    2008-01-01

    Using a sample of 4th and 5th graders, this study investigated whether students’ mathematics anxiety differed significantly according to a group of variables. A total of 249 students participated in the study. “The Mathematics Anxiety Scale for Elementary School Students” and “The Personal Information Form” were used for data collection. Independent samples t-tests, Oneway Anova and Schefee test were used to analyze the data. Results showed that students’ mathematics anxiety differed signific...

  3. 11th National Meeting of Organic Chemistry and 4th Meeting of Therapeutic Chemistry

    Directory of Open Access Journals (Sweden)

    Maria Emília Sousa

    2016-03-01

    Full Text Available For the first time under the auspices of Sociedade Portuguesa de Química, the competences of two important fields of Chemistry are brought together into a single event, the 11st National Organic Chemistry Meeting and the the 4th National Medicinal Chemistry Meeting, to highlight complementarities and to promote new synergies. Abstracts of plenary lectures, oral communications, and posters presented during the meeting are collected in this report.

  4. 11th National Meeting of Organic Chemistry and 4th Meeting of Therapeutic Chemistry

    Science.gov (United States)

    Sousa, Maria Emília; Araújo, Maria João; do Vale, Maria Luísa; Andrade, Paula B.; Branco, Paula; Gomes, Paula; Moreira, Rui; Pinho e Melo, Teresa M.V.D.; Freitas, Victor

    2016-01-01

    For the first time under the auspices of Sociedade Portuguesa de Química, the competences of two important fields of Chemistry are brought together into a single event, the 11st National Organic Chemistry Meeting and the the 4th National Medicinal Chemistry Meeting, to highlight complementarities and to promote new synergies. Abstracts of plenary lectures, oral communications, and posters presented during the meeting are collected in this report. PMID:27102166

  5. Awareness and Attitudes of Primary Grade Teachers (1-4thGrade) towards Inclusive Education

    OpenAIRE

    P. Maheshwari; M. Shapurkar

    2015-01-01

    The present research aimed at studying the awareness and attitudes of teachers towards inclusive education. The sample consisted of 60 teachers, teaching in the primary section (1st – 4th) of regular schools affiliated to the SSC board in Mumbai. Sample was selected by Multi-stage cluster sampling technique. A semi-structured self-constructed interview schedule and a self-constructed attitude scale was used to study the awareness of teachers about disability and Inclusive...

  6. ChemSession'07 - 4th Seminary of Warsaw PhD Students in Chemistry. Abstracts

    International Nuclear Information System (INIS)

    Dobrowolski, J.C.; Ostrowski, S.; Madura, I.; Sporzynski, A.; Szatylowicz, H.; Zubrowska, A.

    2007-01-01

    4 th Annual Seminary of Warsaw PhD Students in Chemistry presented the latest achievements in chemistry, obtained in all Warsaw universities and scientific institutes. In 2007 participants presented 4 plenary lectures, and 101 posters. Among others, posters covered four disciplines related to the nuclear sciences: (a) radiobiology and radiotherapy, (b) radiation chemistry and photochemistry, (c) isotopic effects in chemistry, and (d) chemical technology

  7. HRL Aespoe - two-phase flow experiment - gas and water flow in fractured crystalline rock

    International Nuclear Information System (INIS)

    Kull, H.; Liedtke, L.

    1998-01-01

    (The full text of the contribution follows:) Gas generated from radioactive waste may influence the hydraulic and mechanical properties of the man-made barriers and the immediate surroundings of the repository. Prediction of alteration in fractured crystalline rock is difficult. There is a lack of experimental data, and calibrated models are not yet available. Because of the general importance of this matter the German Federal Ministry for Education, Science, Research and Technology decided to conduct a two-phase flow study at HRL Aespoe within the scope of the co-operation agreement with SKB. Within the presentation an overview of field experiments and modelling studies scheduled until end of '99 are given. Conceptual models for one- and two-phase flow, methodologies and with respect to numerical calculations necessary parameter set-ups are discussed. Common objective of in-situ experiments is to calibrate flow models to improve the reliability of predictions for gas migration through fractured rock mass. Hence, in a defined dipole flow field in niche 2/715 at HRL Aespoe effective hydraulic parameters are evaluated. Numerical modelling of non-isothermal, two-phase, two-component processes is feasible only for two-dimensional representation of a porous medium. To overcome this restriction a computer program will be developed to model three-dimensional, fractured, porous media. Rational aspects of two-phase flow studies are for the designing of geotechnical barriers and for the long-term safety analysis of potential radionuclide transport in a future repository required for the licensing process

  8. Plasma flow switch and foil implosion experiments on Pegasus II

    International Nuclear Information System (INIS)

    Cochrane, J.C.; Bartsch, R.R.; Benage, J.R.; Forman, P.R.; Gribble, R.F.; Ladish, J.S.; Oona, H.; Parker, J.V.; Scudder, D.W.; Shlachter, J.S.; Wysocki, F.J.

    1993-01-01

    Pegasus II is the upgraded version of Pegasus, a pulsed power machine used in the Los Alamos AGEX (Above Ground EXperiments) program. A goal of the program is to produce an intense (> 100 TW) source of soft x-rays from the thermalization of the kinetic energy of a 1 to 10 MJ plasma implosion. The radiation pulse should have a maximum duration of several 10's of nanoseconds and will be used in the study of fusion conditions and material properties. The radiating plasma source will be generated by the thermalization of the kinetic energy of an imploding cylindrical, thin, metallic foil. This paper addresses experiments done on a capacitor bank to develop a switch (plasma flow switch) to switch the bank current into the load at peak current. This allows efficient coupling of bank energy into foil kinetic energy

  9. Energy supply the 4th quarter and the whole years 2000 and 2001, corrected version. Preliminary data

    International Nuclear Information System (INIS)

    2002-01-01

    The objective of the presented statistics is to give a total picture of the Swedish energy supply and its development. The efficiency of the final consumption is not considered in the balance sheets. The quantities (recalculated to tera joules = 10 12 joules) as reported under final consumption refer only to the total energy delivered to the consumers. The final consumption of energy in Sweden the 4th quarter 2001 increased by 5 per cent compared to the corresponding period 2000. The rise can be explained with the fact that the 4th quarter 2001 was colder compared with the same quarter 2000. The consumption within industrial sector was unchanged although the consumption within transports diminished. During the year 2001 energy consumption was unchanged compared with the year 2000. The consumption in household and service sector rose by 8 per cent. The highest rise can be find in the use of district heating and domestic fuels. The industry sector used 5 per cent less energy and mainly in the use of electric energy and domestic fuels. The gross supply of energy in Sweden the 4th quarter increased by 3,5 per cent compared to the 4th quarter 2000. The production of electricity from nuclear plants was 23 per cent higher compared with the same quarter 2000. Hydro-electric power production decreased by 4 per cent during the same period. The supply of natural gas rose by 24 per cent and the supply of domestic fuels rose by 4 %, the supply of coal and coke increased by 3 per cent and the same increase occurred in the supply of oil products. The gross supply of energy was 3 per cent higher during 2001 compared with 2000. The increase can be seen in the supply of coal and coke, 7 per cent, natural gas, 15 per cent, and production of electric energy in nuclear plants, 26 per cent. The balance sheets give both the total flow of various sources of energy and specifications of conversion and consumption in the energy producing industries. The contents of the balance sheets are

  10. 75 FR 38723 - Safety Zone; St. Ignace 4th of July Fireworks, East Moran Bay, Lake Huron, St. Ignace, MI

    Science.gov (United States)

    2010-07-06

    ...-AA00 Safety Zone; St. Ignace 4th of July Fireworks, East Moran Bay, Lake Huron, St. Ignace, MI AGENCY... safety zone on East Moran Bay, Lake Huron, St. Ignace, Michigan. This zone is intended to restrict vessels from a portion of East Moran Bay during the St. Ignace 4th of July Fireworks display, July 4, 2010...

  11. Millimeter-Gap Magnetically Insulated Transmission Line Power Flow Experiments

    Energy Technology Data Exchange (ETDEWEB)

    Hutsel, Brian Thomas [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Stoltzfus, Brian S. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Fowler, William E. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); LeChien, Keith R. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Mazarakis, Michael G. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Moore, James K. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Mulville, Thomas D. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Savage, Mark E. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Stygar, William A. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); McKenney, John L. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Jones, Peter A. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); MacRunnels, Diego J. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Long, Finis W. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Porter, John L. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States)

    2014-09-01

    An experiment platform has been designed to study vacuum power flow in magnetically insulated transmission lines (MITLs). The platform was driven by the 400-GW Mykonos-V accelerator. The experiments conducted quantify the current loss in a millimeter-gap MITL with respect to vacuum conditions in the MITL for two different gap distances, 1.0 and 1.3 mm. The current loss for each gap was measured for three different vacuum pump down times. As a ride along experiment, multiple shots were conducted with each set of hardware to determine if there was a conditioning effect to increase current delivery on subsequent shots. The experiment results revealed large differences in performance for the 1.0 and 1.3 mm gaps. The 1.0 mm gap resulted in current loss of 40%-60% of peak current. The 1.3 mm gap resulted in current losses of less than 5% of peak current. Classical MITL models that neglect plasma expansion predict that there should be zero current loss, after magnetic insulation is established, for both of these gaps. The experiments result s indicate that the vacuum pressure or pump down time did not have a significant effect on the measured current loss at vacuum pressures between 1e-4 and 1e-5 Torr. Additionally, there was not repeatable evidence of a conditioning effect that reduced current loss for subsequent full-energy shots on a given set of hardware. It should be noted that the experiments conducted likely did not have large loss contributions due to ion emission from the anode due to the relatively small current densi-ties (25-40 kA/cm) in the MITL that limited the anode temperature rise due to ohmic heating. The results and conclusions from these experiments may have limited applicability to MITLs of high current density (>400 kA/cm) used in the convolute and load region of the Z which experience temperature increases of >400° C and generate ion emission from anode surfaces.

  12. Can astronomy enhance UNESCO World Heritage recognition? The paradigm of 4th Dynasty Egyptian pyramids

    Science.gov (United States)

    Belmonte, Juan Antonio

    2015-08-01

    The pyramids of Egypt, notably those of the 4th Dinasty as Giza, have always be considered an unmistikable part of human world heritage as the only surviving wonders of the Ancient World. Their majesty, technical hability and innovative character have always beeen considered as representative of ancient Egyptian ingenuity. However, past and present fringe theories about the pyramids and astronomy have always polluted the role of our discipline in the design, construction and symbolism of these impressive monuments. This is indeed unfear. Fortunately, things have started to change in the last couple of decades and now astronomy is interpreted as a neccessary tool for the correct interpretation of the astral eschatology present in the 5th and 6th Dynasty Texts of the Pyramids. Although the pyramid complexes of the 4th Dynasty are mute, there is however recent research showing that a strong astral symbolism could be hidden in many aspects of the complex architecture and in the design of these exceptional monuments. This idea comes from several hints obtained not only from planning and construction, but also from epigraphy and the analysis of celestial and local landscapes. Chronology also plays a most relevant role on this. The pyramid complexes of the 4th Dynasty at Meidum, Dahshur, Giza and Abu Rowash -- all of which enjoy UNESCO World Heritage recognition -- willl be scrutinized. As a consequence, we will show how astronomy can certainly enhance the face value of these extraordinary monuments as a definitive proof of the ancient Egyptian quest for Ma'at, i.e. their perennial obsesion for Cosmic Order.

  13. The 4th Report of the Working Group on ECG diagnosis of Left Ventricular Hypertrophy

    DEFF Research Database (Denmark)

    Bacharova, Ljuba; Estes, Harvey E; Schocken, Douglas D

    2016-01-01

    The 4th Report provides a brief review of publications focused on the electrocardiographic diagnosis of left ventricular hypertrophy published during the period of 2010 to 2016 by the members of the Working Group on ECG diagnosis of Left Ventricular Hypertrophy. The Working Group recommended...... that ECG research and clinical attention be redirected from the estimation of LVM to the identification of electrical remodeling, to better understanding the sequence of events connecting electrical remodeling to outcomes. The need for a re-definition of terms and for a new paradigm is also stressed....

  14. APTWG: The 4th Asia-Pacific Transport Working Group Meeting

    International Nuclear Information System (INIS)

    Ida, K.; Todo, Y.; Kwon, J.M.; Leconte, M.; Ko, W.H.; Inagaki, S.; Kosuga, Y.

    2015-01-01

    This conference report summarizes the contributions to, and discussions at, the 4th Asia-Pacific Transport Working Group Meeting held at Kyushu University, Japan, during 10–13 June 2014. The topics of the meeting were organized under five main headings: turbulence suppression and transport barrier formation, effect of magnetic topology on MHD activity and transport, non-diffusive contribution of momentum and particle transport, non-local transport and turbulence spreading and coupling, energetic particles and instability. The Young Researchers' Forum which was held in this meeting is also described in this report. (conference reports)

  15. Proceedings of the 4th International Workshop on Tritium Effects in Plasma Facing Components

    International Nuclear Information System (INIS)

    Causey, R. A.

    1999-01-01

    The 4th International Workshop on Tritium Effects in Plasma Facing Components was held in Santa Fe, New Mexico on May 14-15, 1998. This workshop occurs every two years, and has previously been held in Livermore/California, Nagoya/Japan, and the JRC-Ispra Site in Italy. The purpose of the workshop is to gather researchers involved in the topic of tritium migration, retention, and recycling in materials used to line magnetic fusion reactor walls and provide a forum for presentation and discussions in this area. This document provides an overall summary of the workshop, the workshop agenda, a summary of the presentations, and a list of attendees

  16. JPRS Report, Science & Technology, Japan, 4th Intelligent Robots Symposium, Volume 1

    Science.gov (United States)

    1989-03-16

    Robots 43064062 Tokyo 4TH INTELLIGENT ROBOTS SYMPOSIUM PAPERS in Japanese 13/14 Jun 88 No 106 pp 39-44 [Article by H. Kimura , I. Shimoyama, and H. Miura...pp 237-239. 3. K. Kondo and F. Kimura , "High-Speed Orbit Planning Based on Labyrinthine Method," Ibid., pp 261-262. 4. T. Hasegawa, "Planning of...Satoshi Okada, Kazuhiro Tsumura, Hisashi Hozeki, Katsumi Kubo, and Akira Abe, Toshiba Corporation] [Text] 1. Introduction In recent years, the

  17. The photoabsorption of Eu, Eu+ and Eu2+ in the vicinity of 4 Th thresholds

    International Nuclear Information System (INIS)

    Amusia, M.Ya.; Chernysheva, L.V.; Ivanov, V.K.

    2000-01-01

    The results of calculations of the total and partial photoionisation cross-sections of neutral Europium and its ions in the photon energy range from the threshold up to 270 eV are presented. The calculations were performed within the multi-channel Spin-Polarized Random Phase Approximation with Exchange. The main attention is given to the giant autoionizing resonance associated with the 4 Th → 4 f discrete transition to vacant states in the 4f 7 subshell. The comparisons with experimental data obtained recently and the results of previous calculations are made.

  18. “Team Building: Proven Strategies for Improving Team Performance, 4th Edition”

    Directory of Open Access Journals (Sweden)

    Greg Homan

    2008-12-01

    Full Text Available Team Building is an important issue for Youth Development professionals. We utilize team-focused work to achieve our objectives in educating youth. The team building skills we integrate into programming serve to prepare youth for the dynamic, highly interpersonal work environment of today. “Team Building: Proven Strategies for Improving Team Performance, 4th Edition,” by W. Dyer, W.G. Dyer, and J. Dyer (2007, provides a practical theoretical framework for those interested in team building application, training, and practice in everyday work.

  19. Generalized effective potential in nonlinear theories of the 4-th order

    International Nuclear Information System (INIS)

    Ananikyan, N.S.; Savvidy, G.K.

    1980-01-01

    By means of the Legendre transformations in the framework of nonlinear theories of the 4-th order a generalized effective potential GITA(phi, G, H, S) is constructed. It depends on PHI, a possible expectation value of the quantum field; on G, H, possible expectation values of the 2- a.nd 3-point connected Green functions and on S= a possible expectation value of the classical action. The expansion for the functional GITA(phi, G, H, S) is obtained, which is similar to the loop expansion for the effective action GITA(phi)

  20. 4. mednarodna znanstvena konferenca Management - teorija in praksa = 4th international conference Management Theory and Practice

    Directory of Open Access Journals (Sweden)

    Ana Arzenšek

    2009-06-01

    Full Text Available At the beginning of April 2009 the second largest city of Estonia was host to the 4th international conference Management Theory and Practice. The thematic emphasis of this year’s conference was Synergy in Organisations. The conference is biannually organised by the Institute of Business Administration of the University of Tartu, Faculty of Economics and Business Administration. In a year of innovation, special attention was given to creativity and innovation in management. Altogether, 40 papers were presented and more than 50 participants participated in the conference. The next, 5th conference, will take place in 2011.

  1. Semi-brittle flow of granitoid fault rocks in experiments

    Science.gov (United States)

    Pec, Matej; Stünitz, Holger; Heilbronner, Renée.; Drury, Martyn

    2016-03-01

    Field studies and seismic data show that semi-brittle flow of fault rocks probably is the dominant deformation mechanism at the base of the seismogenic zone at the so-called frictional-viscous transition. To understand the physical and chemical processes accommodating semi-brittle flow, we have performed an experimental study on synthetic granitoid fault rocks exploring a broad parameter space (temperature, T = 300, 400, 500, and 600°C, confining pressure, Pc ≈ 300, 500, 1000, and 1500 MPa, shear strain rate, γṡ ≈ 10-3, 10-4, 10-5, and 10-6 s-1, to finite shear strains, γ = 0-5). The experiments have been carried out using a granular material with grain size smaller than 200 µm with a little H2O added (0.2 wt %). Only two experiments (performed at the fastest strain rates and lowest temperatures) have failed abruptly right after reaching peak strength (τ ~ 1400 MPa). All other samples reach high shear stresses (τ ~ 570-1600 MPa) then weaken slightly (by Δτ ~ 10-190 MPa) and continue to deform at a more or less steady state stress level. Clear temperature dependence and a weak strain rate dependence of the peak as well as steady state stress levels are observed. In order to express this relationship, the strain rate-stress sensitivity has been fit with a stress exponent, assuming γ˙ ∝ τn and yields high stress exponents (n ≈ 10-140), which decrease with increasing temperature. The microstructures show widespread comminution, strain partitioning, and localization into slip zones. The slip zones contain at first nanocrystalline and partly amorphous material. Later, during continued deformation, fully amorphous material develops in some of the slip zones. Despite the mechanical steady state conditions, the fabrics in the slip zones and outside continue to evolve and do not reach a steady state microstructure below γ = 5. Within the slip zones, the fault rock material progressively transforms from a crystalline solid to an amorphous material. We

  2. QUICK-FIRE: Plasma flow driven implosion experiments

    International Nuclear Information System (INIS)

    Baker, W.L.; Bigelow, W.S.; Degnan, J.H.

    1985-01-01

    High speed plasma implosions involving megajoules of energy, and sub-microsecond implosion times are expected to require additional stages of power conditioning between realistic primary energy sources and the implosion system. Plasma flow switches and vacuum inductive stores represent attractive alternates to the high speed fuse and atmospheric store techniques which have been previously reported for powering such plasma experiments. In experiments being conducted at the Air Force Weapons Lab, a washer shaped plasma accelerated to 7-10 cm/microsecond in a coaxial plasma gun configuration, represents the moving element in a vacuum store/power conditioning system of 16.5 nH inductance which stores 1-1.5 MJ at 12-14 MA. At the end of the coaxial gun, the moving element transits the 2cm axial length of the cylindrical implosion gap in 200-400 nS, delivering the magnetic energy to the implosion foil, accelerating the imploding plasma to speeds of 30-40 cm/microsecond in 350-450 nS, and delivering a projected 400 KJ of kinetic energy to the implosion

  3. Development of Flow Boiling and Condensation Experiment on the International Space Station- Normal and Low Gravity Flow Boiling Experiment Development and Test Results

    Science.gov (United States)

    Nahra, Henry K.; Hall, Nancy R.; Hasan, Mohammad M.; Wagner, James D.; May, Rochelle L.; Mackey, Jeffrey R.; Kolacz, John S.; Butcher, Robert L.; Frankenfield, Bruce J.; Mudawar, Issam; hide

    2013-01-01

    Flow boiling and condensation have been identified as two key mechanisms for heat transport that are vital for achieving weight and volume reduction as well as performance enhancement in future space systems. Since inertia driven flows are demanding on power usage, lower flows are desirable. However, in microgravity, lower flows are dominated by forces other than inertia (like the capillary force). It is of paramount interest to investigate limits of low flows beyond which the flow is inertial enough to be gravity independent. One of the objectives of the Flow Boiling and Condensation Flight Experiment sets to investigate these limits for flow boiling and condensation. A two-phase flow loop consisting of a Flow Boiling Module and two Condensation Modules has been developed to experimentally study flow boiling condensation heat transfer in the reduced gravity environment provided by the reduced gravity platform. This effort supports the development of a flow boiling and condensation facility for the International Space Station (ISS). The closed loop test facility is designed to deliver the test fluid, FC-72 to the inlet of any one of the test modules at specified thermodynamic and flow conditions. The zero-g-aircraft tests will provide subcooled and saturated flow boiling critical heat flux and flow condensation heat transfer data over wide range of flow velocities. Additionally, these tests will verify the performance of all gravity sensitive components, such as evaporator, condenser and accumulator associated with the two-phase flow loop. We will present in this paper the breadboard development and testing results which consist of detailed performance evaluation of the heater and condenser combination in reduced and normal gravity. We will also present the design of the reduced gravity aircraft rack and the results of the ground flow boiling heat transfer testing performed with the Flow Boiling Module that is designed to investigate flow boiling heat transfer and

  4. PREFACE: 4th International Conference on Mathematical Modeling in Physical Sciences (IC-MSquare2015)

    Science.gov (United States)

    Vlachos, Dimitrios; Vagenas, Elias C.

    2015-09-01

    The 4th International Conference on Mathematical Modeling in Physical Sciences (IC-MSQUARE) took place in Mykonos, Greece, from Friday 5th June to Monday 8th June 2015. The Conference was attended by more than 150 participants and hosted about 200 oral, poster, and virtual presentations. There were more than 600 pre-registered authors. The 4th IC-MSQUARE consisted of different and diverging workshops and thus covered various research fields where Mathematical Modeling is used, such as Theoretical/Mathematical Physics, Neutrino Physics, Non-Integrable Systems, Dynamical Systems, Computational Nanoscience, Biological Physics, Computational Biomechanics, Complex Networks, Stochastic Modeling, Fractional Statistics, DNA Dynamics, Macroeconomics etc. The scientific program was rather intense as after the Keynote and Invited Talks in the morning, three parallel oral and one poster session were running every day. However, according to all attendees, the program was excellent with a high quality of talks creating an innovative and productive scientific environment for all attendees. We would like to thank the Keynote Speaker and the Invited Speakers for their significant contribution to IC-MSQUARE. We also would like to thank the Members of the International Advisory and Scientific Committees as well as the Members of the Organizing Committee.

  5. The 2002 activities and the 4th workshop of the human resources development project in FNCA

    International Nuclear Information System (INIS)

    2003-07-01

    In 1999, the Project for Human Resources Development (HRD Project) was initiated as defined in the framework of the Forum for Nuclear Cooperation in Asia (FNCA), organized by the Atomic Energy Commission of Japan. The objective of the HRD Project is to solidify the foundation of technologies for nuclear development and utilization in Asia by promoting human resources development in Asian countries. In the Project there are two kinds of activity; In-workshop activity and Outside-of-workshop activity. The 4th Workshop on HRD Project was held on october 8-10, 2002, in Batangas, the Philippines. The Workshop was sponsored by the Department of Science and Technology (DOST) of the Philippines and the Ministry of Education, Culture, Sports, Science and Technology (MEXT) of Japan. The Philippine Nuclear Research Institute (PNRI) and the Japan Atomic Energy Research Institute (JAERI) acted as the hosts. Participating countries were China, Indonesia, Republic of Korea, Japan, Malaysia, the Phillippines, Thailand, and Vietnam. This report consists of presentation papers and materials at the 4th workshop as In-Workshop Activity, a review document of HRD Project for the 5th Coordinators Meeting of FNCA at Tokyo on March, 2003, a letter of proposal from the Project Leader of Japan to the Project Leaders of the participating countries, and training materials of participating countries as Outside-Workshop Activity. (author)

  6. Fast and Analytical EAP Approximation from a 4th-Order Tensor

    Directory of Open Access Journals (Sweden)

    Aurobrata Ghosh

    2012-01-01

    Full Text Available Generalized diffusion tensor imaging (GDTI was developed to model complex apparent diffusivity coefficient (ADC using higher-order tensors (HOTs and to overcome the inherent single-peak shortcoming of DTI. However, the geometry of a complex ADC profile does not correspond to the underlying structure of fibers. This tissue geometry can be inferred from the shape of the ensemble average propagator (EAP. Though interesting methods for estimating a positive ADC using 4th-order diffusion tensors were developed, GDTI in general was overtaken by other approaches, for example, the orientation distribution function (ODF, since it is considerably difficult to recuperate the EAP from a HOT model of the ADC in GDTI. In this paper, we present a novel closed-form approximation of the EAP using Hermite polynomials from a modified HOT model of the original GDTI-ADC. Since the solution is analytical, it is fast, differentiable, and the approximation converges well to the true EAP. This method also makes the effort of computing a positive ADC worthwhile, since now both the ADC and the EAP can be used and have closed forms. We demonstrate our approach with 4th-order tensors on synthetic data and in vivo human data.

  7. Fast and Analytical EAP Approximation from a 4th-Order Tensor.

    Science.gov (United States)

    Ghosh, Aurobrata; Deriche, Rachid

    2012-01-01

    Generalized diffusion tensor imaging (GDTI) was developed to model complex apparent diffusivity coefficient (ADC) using higher-order tensors (HOTs) and to overcome the inherent single-peak shortcoming of DTI. However, the geometry of a complex ADC profile does not correspond to the underlying structure of fibers. This tissue geometry can be inferred from the shape of the ensemble average propagator (EAP). Though interesting methods for estimating a positive ADC using 4th-order diffusion tensors were developed, GDTI in general was overtaken by other approaches, for example, the orientation distribution function (ODF), since it is considerably difficult to recuperate the EAP from a HOT model of the ADC in GDTI. In this paper, we present a novel closed-form approximation of the EAP using Hermite polynomials from a modified HOT model of the original GDTI-ADC. Since the solution is analytical, it is fast, differentiable, and the approximation converges well to the true EAP. This method also makes the effort of computing a positive ADC worthwhile, since now both the ADC and the EAP can be used and have closed forms. We demonstrate our approach with 4th-order tensors on synthetic data and in vivo human data.

  8. Crime rates and sedentary behavior among 4th grade Texas school children

    Directory of Open Access Journals (Sweden)

    Hoelscher Deanna M

    2008-05-01

    Full Text Available Abstract Introduction Although per capita crime has generally fallen over the period which coincides with the obesity epidemic, it has not fallen uniformly across communities. It also has not fallen enough to allay fears on the part of parents. Over the past 30 years, technological changes have made the indoor alternatives to playing outside, where children are more vulnerable to criminal activity, more enjoyable (cable TV, video games, and the internet and comfortable (the spread of air conditioning to low income neighborhoods. We determined whether indoor sedentary behavior patterns are associated with community crime statistics. 4th graders in the U.S. are typically 9 or 10 years old. Methods We used data from the 2004–2005 Texas School Physical Activity and Nutrition (SPAN survey linked with U.S. Department of Justice, Office of Justice Programs, Bureau of Justice Statistics data for the years 2000 through 2005 and Texas State data on sexual offenders. The probability-based sample included a total of 7,907 children in grade four. Multistage probability sampling weights were used. The dependent variables included were hours of TV watching, video game playing, computer use and total indoor sedentary behavior after school. Incremental Relative Rates were computed for community crime rates including robberies, all violent crimes, murders, assaults, property crimes, rapes, burglaries, larcenies and motor vehicle thefts as well as for sexual offenders living in the neighborhood. The neighborhood refers to the areas where the students at each school live. In the case of sexual offenders, sexual offenders per capita are estimated using the per capita rate in the zip code of the school attended; all other crime statistics are estimated by the crimes per capita in the police department jurisdiction covering the school attended. After controlling for sex, age, and African-American and Hispanic, cross-sectional associations were determined using

  9. Quick-fire: Plasma flow driven implosion experiments

    International Nuclear Information System (INIS)

    Baker, W.L.; Bigelow, W.S.; Degnan, J.H.

    1985-01-01

    High speed plasma implosions involving megajoules of energy, and sub-microsecond implosion times are expected to require additional stages of power conditioning between realistic primary energy sources and the implosion system. Plasma flow switches and vacuum inductive stores represent attractive alternates to the high speed fuse and atmospheric store techniques which have been previously reported for powering such plasma experiments. In experiments being conducted at the Air Force Weapons Lab, a washer shaped plasma accelerated to 7-10 cm/microsecond in a coaxial plasma gun configuration, represents the moving element in a vacuum store/power conditioning system of 16.5 nH inductance which stores 1-1.5 MJ at 12-14 MA. At the end of the coaxial gun, the moving element transits the 2cm axial length of the cylindrical implosion gap in 200-400 nS, delivering the magnetic energy to the implosion foil, accelerating the imploding plasma to speeds of 30-40 cm/microsecond in 350-450 nS, and delivering a projected 400 KJ of kinetic energy to the implosion. Experiments have been conducted using the SHIVA STAR capacitor bank operating at 6 MJ stored energy in which performance has been monitored by electrical diagnostics, magnetic probes, and axial and radial viewing high speed visible and X-Ray photographs to assess the performance of the coaxial run and coaxial to radial transition. Time and spectrally resolved X-Ray diagnostics are used to assess implosion quality and performance and results are compared to kinematic and MHD models

  10. Effectiveness of ivermectin against later 4th-stage Strongylus vulgaris in ponies.

    Science.gov (United States)

    Slocombe, J O; McCraw, B M; Pennock, P W; Vasey, J

    1982-09-01

    Twelve pony foals were reared worm-free and inoculated with Strongylus vulgaris. Approximately 8 weeks after they were inoculated, 6 foals were given ivermectin IM at a dosage rate of 200 micrograms/kg of body weight and 6 were given a placebo. All foals were necropsied 35 days after treatment. Ivermectin was 98.9% effective in eliminating later 4th-stage S vulgaris larvae located near the origin of major intestinal arteries and in reducing clinical signs and permitting resolution of lesions associated with verminous arteritis. One pony foal reared on pasture and with evidence of arteritis of the cranial mesenteric and ileocolic arteries on arteriography was treated with ivermectin at a dosage rate of 200 micrograms/kg of body weight. On arteriographs taken subsequently, there was evidence of regression of the lesion, and at necropsy 9 weeks after treatment, there was no arteritis or larvae in those arteries.

  11. Interviews with Michael Baxandall, February 3rd and 4th, 1994, Berkeley, CA

    Directory of Open Access Journals (Sweden)

    Allan Langdale

    2009-12-01

    Full Text Available The following interviews with Michael Baxandall were conducted in Berkeley on February 3rd and 4th of 1994. The content of these interviews include general responses about developments in art history in the years between 1960 and 1985, a period of dramatic modifications in the discipline. Among the issues are the rise of the social history of art and the sources from anthropology that informed Baxandall’s concept of the ‘Period Eye’. Baxandall talks about his own work, his personal intellectual history, and the scholars of past and current generations who influenced him. Other topics include Baxandall’s professional trajectory, the Warburg Library, and aspects of cultural history having to do with Renaissance Humanism. These interviews first appeared as an appendix to the PhD dissertation by Allan Langdale, Art History and Intellectual History: Michael Baxandall’s Work between 1963 and 1985, U. C. Santa Barbara, 1995.

  12. 4th International Workshop on Adaptive Optics for Industry and Medicine

    CERN Document Server

    Wittrock, Ulrich

    2005-01-01

    This book treats the development and application of adaptive optics for industry and medicine. The contributions describe recently developed components for adaptive-optics systems such as deformable mirrors, wavefront sensors, and mirror drivers as well as complete adaptive optical systems and their applications in industry and medicine. Applications range from laser-beam forming and adaptive aberration correction for high-power lasers to retinal imaging in ophthalmology. The contributions are based on presentations made at the 4th International Workshop on Adaptive Optics in Industry and Medicine which took place in Münster, Germany, in October 2003. This highly successful series of workshops on adaptive optics started in 1997 and continues with the 5th workshop in Beijing in 2005.

  13. [3rd and 4th generation estroprogestatives French controversy: What effect on women's behavior?].

    Science.gov (United States)

    Torres, Luis; Frapard, Christian; Daumas, Aurélie; Guibert, Nicolas; Lagouanelle-Simeoni, Marie-Claude; Rakoto, Jean-Claude; Villani, Patrick; Sambuc, Roland

    2016-04-01

    The primary objective of this study was to determine the reasons given by women who have changed or suspended their contraceptive method in 2013. What influence had the 3rd and 4th generation estroprogestatives (EP) French controversy and advices from doctors? Did they notice any consequences of the controversy on their lifestyle? Did they feel an impact on their behavior to health professionals? A study was conducted on women of childbearing age. Data collection took place between November 4 and December 16, 2013. The included subjects were between 18 and 55 years old females. Subjects were surveyed through an anonymous self-administered questionnaire distributed through pharmacies. The protocol called for the construction of clusters of subjects by having heard about, or not, of the controversy. Patients reporting having heard about the controversy have formed the "exposed" group while the others have formed the "unexposed" group. We compared two parameters between these two groups: the rate of subjects who reported having modified or suspended their contraceptive method in 2013 on one hand, and the rate of subjects who reported having made a change in their contraceptive method without or against advices from a doctor on the other hand. The sample included 988 subjects. The average age was 34 years. The level of exposure to media debates was 86.5%. Of the respondents, 19.8% were under 3rd or 4th generation EP in 2012, thus directly involved in the discussions and affected by health recommendations. Of the patients, 38.5% reported having changed their contraception in 2013. In these women, when they confirmed having heard about the controversy, 40.1% of them claimed to have conducted this process without or against advices from a doctor. This number dropped to 18.2% for those who had not heard of it. Media coverage of the 3rd and 4th generation EP vascular risk was not mentioned more by patients who suspended all medical contraceptive method than it was by

  14. 4th International Conference on Innovations in Bio-Inspired Computing and Applications

    CERN Document Server

    Krömer, Pavel; Snášel, Václav

    2014-01-01

    This volume of Advances in Intelligent Systems and Computing contains accepted papers presented at IBICA2013, the 4th International Conference on Innovations in Bio-inspired Computing and Applications. The aim of IBICA 2013 was to provide a platform for world research leaders and practitioners, to discuss the full spectrum of current theoretical developments, emerging technologies, and innovative applications of Bio-inspired Computing. Bio-inspired Computing is currently one of the most exciting research areas, and it is continuously demonstrating exceptional strength in solving complex real life problems. The main driving force of the conference is to further explore the intriguing potential of Bio-inspired Computing. IBICA 2013 was held in Ostrava, Czech Republic and hosted by the VSB - Technical University of Ostrava.

  15. 4th International Conference on Condition Monitoring of Machinery in Non-Stationary Operations

    CERN Document Server

    Zimroz, Radoslaw; Bartelmus, Walter; Haddar, Mohamed

    2016-01-01

    The book provides readers with a snapshot of recent research and technological trends in the field of condition monitoring of machinery working under a broad range of operating conditions. Each chapter, accepted after a rigorous peer-review process, reports on an original piece of work presented and discussed at the 4th International Conference on Condition Monitoring of Machinery in Non-stationary Operations, CMMNO 2014, held on December 15-16, 2014, in Lyon, France. The contributions have been grouped into three different sections according to the main subfield (signal processing, data mining, or condition monitoring techniques) they are related to. The book includes both theoretical developments as well as a number of industrial case studies, in different areas including, but not limited to: noise and vibration; vibro-acoustic diagnosis; signal processing techniques; diagnostic data analysis; instantaneous speed identification; monitoring and diagnostic systems; and dynamic and fault modeling. This book no...

  16. Searching for 4th generation fermions at high-energy e+e- machines

    International Nuclear Information System (INIS)

    Dorfan, J.; Van Kooten, R.J.

    1987-05-01

    This writeup summarizes Monte Carlo studies on the feasibility of searching for 4th family fermions at high energy e + e - machines. By high energy it is meant at energies beyond the Z 0 ; the Z 0 searches having been studied extensively by the SLC and LEP collaborations. The specific examples of √s = 200 GeV (namely LEP200) and √s = 600 GeV (in line with work being done at SLAC to investigate the potential of a future linear collider) were chosen. The studies have been performed with the four vectors produced by the models and no attempt has been made to account for the effects of finite resolution and inefficiencies due to a real detector environment

  17. Giant partially thrombosed 4 th ventricular posterior inferior cerebellar artery aneurysm; microsurgical management

    Directory of Open Access Journals (Sweden)

    Forhad Hossain Chowdhury

    2014-01-01

    Full Text Available A 42-year-old woman presented with a 3-month history of progressive occipital headache, vomiting, walking difficulty, and repeated fall. She had no history of sudden and severe headache. She had positive cerebellar signs, predominantly on the right side. Computerized tomography (CT scan, CT angiogram, and magnetic resonance image (MRI of the brain showed suspected partially thrombosed giant 4 th ventricular posterior inferior cerebellar artery aneurysm. Patient developed severe hypersensitivity reaction during both CT scan and MRI after contrast injection. Though needed, digital subtraction angiogram (DSA of cerebral vessels was not done. The aneurysm was managed by microsurgical clipping of the aneurysm neck and partial excision of thrombosed aneurysm. Here, we report the details of management of these difficult giant aneurysm without DSA.

  18. PV Performance Modeling Methods and Practices: Results from the 4th PV Performance Modeling Collaborative Workshop.

    Energy Technology Data Exchange (ETDEWEB)

    Stein, Joshua [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States)

    2017-03-01

    In 2014, the IEA PVPS Task 13 added the PVPMC as a formal activity to its technical work plan for 2014-2017. The goal of this activity is to expand the reach of the PVPMC to a broader international audience and help to reduce PV performance modeling uncertainties worldwide. One of the main deliverables of this activity is to host one or more PVPMC workshops outside the US to foster more international participation within this collaborative group. This report reviews the results of the first in a series of these joint IEA PVPS Task 13/PVPMC workshops. The 4th PV Performance Modeling Collaborative Workshop was held in Cologne, Germany at the headquarters of TÜV Rheinland on October 22-23, 2015.

  19. 4th International Conference on Frontiers in Intelligent Computing : Theory and Applications

    CERN Document Server

    Pal, Tandra; Kar, Samarjit; Satapathy, Suresh; Mandal, Jyotsna

    2016-01-01

    The proceedings of the 4th International Conference on Frontiers in Intelligent Computing: Theory and Applications 2015 (FICTA 2015) serves as the knowledge centre not only for scientists and researchers in the field of intelligent computing but also for students of post-graduate level in various engineering disciplines. The book covers a comprehensive overview of the theory, methods, applications and tools of Intelligent Computing. Researchers are now working in interdisciplinary areas and the proceedings of FICTA 2015 plays a major role to accumulate those significant works in one arena. The chapters included in the proceedings inculcates both theoretical as well as practical aspects of different areas like Nature Inspired Algorithms, Fuzzy Systems, Data Mining, Signal Processing, Image processing, Text Processing, Wireless Sensor Networks, Network Security and Cellular Automata. .

  20. 4th International Conference on Computational Collective Intel- ligence Technologies and Applications (ICCCI 2012)

    CERN Document Server

    Trawiński, Bogdan; Katarzyniak, Radosław; Jo, Geun-Sik; Advanced Methods for Computational Collective Intelligence

    2013-01-01

    The book consists of 35 extended chapters which have been selected and invited from the submissions to the 4th International Conference on Computational Collective Intelligence Technologies and Applications (ICCCI 2012) held on November 28-30, 2012 in Ho Chi Minh City, Vietnam. The book is organized into six parts, which are semantic web and ontologies, social networks and e-learning, agent and multiagent systems, data mining methods and applications, soft computing, and optimization and control, respectively. All chapters in the book discuss theoretical and practical issues connected with computational collective intelligence and related technologies. The editors hope that the book can be useful for graduate and Ph.D. students in Computer Science, in particular participants in courses on Soft Computing, Multiagent Systems, and Data Mining. This book can be also useful for researchers working on the concept of computational collective intelligence in artificial populations. It is the hope of the editors that ...

  1. Idaho National Laboratory Quarterly Occurrence Analysis 4th Quarter FY 2016

    Energy Technology Data Exchange (ETDEWEB)

    Mitchell, Lisbeth Ann [Idaho National Lab. (INL), Idaho Falls, ID (United States)

    2016-11-01

    This report is published quarterly by the Idaho National Laboratory (INL) Quality and Performance Management Organization. The Department of Energy (DOE) Occurrence Reporting and Processing System, as prescribed in DOE Order 232.2, “Occurrence Reporting and Processing of Operations Information,” requires a quarterly analysis of events, both reportable and not reportable, for the previous 12 months. This report is the analysis of 84 reportable events (29 from the 4th quarter fiscal year 2016 and 55 from the prior three reporting quarters), as well as 39 other issue reports (including events found to be not reportable and Significant Category A and B conditions) identified at INL during the past 12 months (two from this quarter and 37 from the prior three quarters).

  2. The 4th surveillance testing for Kori unit 3 reactor vessel materials

    Energy Technology Data Exchange (ETDEWEB)

    Chang, Kee Ok; Kim, Byoung Chul; Lee, Sam Lai; Choi, Kwun Jae; Gong, Un Sik; Chang, Jong Hwa; Joo, Yong Sun; Ahn, Sang Bok; Hong, Joon Hwa [Korea Atomic Energy Research Institute, Taejeon (Korea)

    2000-10-01

    Surveillance testing for reactor vessel materials is performed in order to evaluate the irradiation embrittlement due to neutrons during operation and set the condition of safe operation of nuclear reactor. The 4th surveillance testing was performed completely by Korea Atomic Energy Research Institute at Taejeon after the capsule was transported from Kori site including its removal from reactor. Fast neutron fluences for capsules were calculated and various testing including mechanical and chemistry analysis were performed in order to evaluate the integrity of Kori unit 3 reactor vessel during the operation until life time. The evaluation results are as follows; Fast neutron fluences for capsules U, V, X and W are 4.983E+18, 1.641E+19, 3.158E+19, and 4.469E+19n/cm{sup 2}, respectively. The bias factor, the ratio of calculation/measurement, was 0.840 for the 1st through 4th testing and the calculational uncertainty, 12% satisfied the requirement of USNRC Reg.Guide DG-1053, 20%. The best estimated neutron fluence for reactor vessel inside surface was 1.362E+19n/cm{sup 2} based on the end of 12th fuel cycle and it was predicted that the fluences of vessel inside surface at 32, 40, 48 and 56EFPY would reach 3.481E+19, 4.209E+19, 5.144E+19 and 5.974E+19n/cm{sup 2} based on the current calculation. The result through this analysis for Kori unit 3 showed that there would be no problem for the pressurized thermal shock(PTS) during the operation until design life. 48 refs., 35 figs., 41 tabs. (Author)

  3. 4th Circuit: asymptomatic HIV is not a disability under ADA.

    Science.gov (United States)

    1997-09-05

    The 4th U.S. Circuit Court of Appeals ruled that [name removed], who is HIV-positive, cannot continue with his lawsuit alleging that NationsBank of Maryland fired him because of his HIV status. The court decided that [name removed] did not make a case of discrimination against his employer because his work performance was substandard. Additionally, the court ruled that HIV infection in and of itself does not constitute a disability and therefore [name removed] is not protected by the Americans with Disabilities Act (ADA). The court ruled that [name removed] failed to prove that his asymptomatic HIV infection was an impairment or that it substantially limits a major life activity. When the ADA was enacted in 1990 it was presumed that anyone with HIV would be protected from discrimination and reports filed by both the House of Representatives and the Senate indicated that legislators felt that HIV infection constituted an impairment. This ruling made by the 4th Circuit seems to discount the legislation's intent. The court rejected [name removed]'s suggestion that the ability to procreate and engage in intimate sexual relations was a limitation of a major life activity. Dissenters argued that the opinion is not based on sound medical facts because HIV, even if it is asymptomatic, is an impairment. The dissent also contends that Mr. [Name removed] was not given fair and ample opportunity to prove that his HIV infection is disabling. The court was in sharp disagreement relative to [name removed]'s job performance. The court majority said that [name removed] failed to meet sales goals and engaged in unprofessional behavior. The dissent countered that [name removed]'s sales record exceeded that of another employee who was not terminated.

  4. Fuels. Deliveries and consumption of fuels during 4th quarter 2001 and during 2001

    International Nuclear Information System (INIS)

    2002-01-01

    The total volume of oil product deliveries (excluded lubricants, bitumen etc.) from the oil companies was 3 per cent higher during 2001 compared with 2000. The deliveries of motor gasoline and diesel oil increased by 1 per cent. Domestic heating oil decreased by 2 per cent and heavy fuel oils increased by 17 per cent, all compared with 2000. Under the forth quarter 2001 the deliveries of oil products (excluded lubricants bitumen etc.) was 5 per cent higher compared with the same quarter 2000. The deliveries of domestic heating oil and heavy fuel oils increased by 4 per cent and 28 per cent respectively. Motor gasoline increased by 3 per cent while the deliveries of diesel oil decreased by 1 per cent. The consumption of fuels in mining and manufacturing decreased by 5 per cent during 2001 compared with 2000. Most of the reduction came from the lower use of domestic fuel in manufacture of pulp, paper and paper products, printing and publishing. The total consumption in mining and manufacturing was unchanged during the 4 th quarter 2001 compared with the same period 2000. The consumption of domestic fuels decreased by 6 per cent and the oil consumption increased by 11 per cent. Higher consumption of fuels in electricity, gas and district heating services. The consumption of fuels in electricity, gas and district heating services increased by 14 per cent 2001 compared with 2000. The consumption of domestic fuels raised with 12 per cent and the use of fossil fuels raised with 17 per cent. The highest increasing, 27 per cent, was found within the use of oil. Electricity, gas and district heating services increased there fuel consumption with 29 per cent during the 0 quarter 2001 compared with the same period 2000. The raise can be explained with the fact that the 4th quarter 2000 was unusually warm. The increasing is found both in the use of domestic and fossil fuels

  5. Sensitivity of Velocity Picking on 4th Order Non Hyperbolic Move out Correction

    International Nuclear Information System (INIS)

    Enuma, C.; Hope, R.; Idoko, P.

    2003-01-01

    Long offset processing has become the standard for TotaFinaElf in the Deep Offshore Nigeria. The advantage of having longer offsets are numerous; higher fold of coverage, improved S/N improved AVA analysis, less multiple contamination etc. A key element in successful long offset processing is the higher order velocity picking. In classical processing of seismic data with standard 2nd order terms for NMO correction, and outer mute at approximately 27 degrees, not to include non flattened events is required. By applying 3 terms 4th order anisotropic non hyperbolic corrections, angles out to 50-60 degrees may be flattened and can be very useful. Typically in modern 3D seismic data processing velocities are picked every 1km or 0.5km. a test was carried out to study the effect of the lateral velocity pick spacing required to properly flatten events at longer offsets. The evaluation of the test w3as carried out by loading all the CMP gathers along the line on a workstation as a 3D so that the flatness on pre-stack could be studied. The analysis showed that for 2nd order NMO 0.5km spacing is adequate to properly interpolate and flatten events at all CMP gathers along the line. However it was shown that for more advanced processing, such as the 4th order anisotropic three terms non hyperbolic velocity corrections, a more dense lateral velocity picking would be advantageous in terms of flattening of reflections. This presentation show how important long offset processing is and especially the importance of velocity picking

  6. Two-phase flow experiments through intergranular stress corrosion cracks

    International Nuclear Information System (INIS)

    Collier, R.P.; Norris, D.M.

    1984-01-01

    Experimental studies of critical two-phase water flow, through simulated and actual intergranular stress corrosion cracks, were performed to obtain data to evaluate a leak flow rate model and investigate acoustic transducer effectiveness in detecting and sizing leaks. The experimental program included a parametric study of the effects of crack geometry, fluid stagnation pressure and temperature, and crack surface roughness on leak flow rate. In addition, leak detection, location, and leak size estimation capabilities of several different acoustic transducers were evaluated as functions of leak rate and transducer position. This paper presents flow rate data for several different cracks and fluid conditions. It also presents the minimum flows rate detected with the acoustic sensors and a relationship between acoustic signal strength and leak flow rate

  7. Report on the 4th Europhysics Workshop on the role of electric fields in plasma confinement and exhaust (Funchal, Madeira, 24-25 June 2001)

    International Nuclear Information System (INIS)

    Oost, G. van; Tendler, M.

    2002-01-01

    The 4th Europhysics Workshop was organized in Funchal in Madeira as a Satellite Meeting of the 28th EPS Conference on Controlled Fusion and Plasma Physics, and attended by about 45 scientists from 15 countries. It was hosted by the Portuguese Association IST-Euratom, and organized by the Czech Association Euratom/IPP.CR. The scope of the workshop is broad and includes experiments, techniques, theory and modelling pertinent to the effects of electric fields on plasmas. After refereeing, 18 of the 27 (oral) contributions were published in the October 2001 issue of Czechoslovak Journal of Physics. (author)

  8. COUNTERCURRENT FLOW LIMITATION EXPERIMENTS AND MODELING FOR IMPROVED REACTOR SAFETY

    International Nuclear Information System (INIS)

    Vierow, Karen

    2008-01-01

    This project is investigating countercurrent flow and 'flooding' phenomena in light water reactor systems to improve reactor safety of current and future reactors. To better understand the occurrence of flooding in the surge line geometry of a PWR, two experimental programs were performed. In the first, a test facility with an acrylic test section provided visual data on flooding for air-water systems in large diameter tubes. This test section also allowed for development of techniques to form an annular liquid film along the inner surface of the 'surge line' and other techniques which would be difficult to verify in an opaque test section. Based on experiences in the air-water testing and the improved understanding of flooding phenomena, two series of tests were conducted in a large-diameter, stainless steel test section. Air-water test results and steam-water test results were directly compared to note the effect of condensation. Results indicate that, as for smaller diameter tubes, the flooding phenomena is predominantly driven by the hydrodynamics. Tests with the test sections inclined were attempted but the annular film was easily disrupted. A theoretical model for steam venting from inclined tubes is proposed herein and validated against air-water data. Empirical correlations were proposed for air-water and steam-water data. Methods for developing analytical models of the air-water and steam-water systems are discussed, as is the applicability of the current data to the surge line conditions. This report documents the project results from July 1, 2005 through June 30, 2008

  9. Clearance gap flow: Simulations by discontinuous Galerkin method and experiments

    Czech Academy of Sciences Publication Activity Database

    Hála, Jindřich; Luxa, Martin; Bublík, O.; Prausová, H.; Vimmr, J.

    2016-01-01

    Roč. 92, May (2016), 02073-02073 ISSN 2100-014X. [EFM14 – Experimental Fluid Mechanics 2014. Český Krumlov, 18.11.2014-21.11.2014] Institutional support: RVO:61388998 Keywords : compressible fluid flow * narrow channel flow * discontinuous Galerkin finite element method Subject RIV: BK - Fluid Dynamics

  10. Flow Monitoring Experiences at the Ethernet-Layer

    NARCIS (Netherlands)

    Hofstede, Rick; Hofstede, R.J.; Drago, Idilio; Sperotto, Anna; Pras, Aiko; Lehnert, Ralf

    2011-01-01

    Flow monitoring is a scalable technology for providing summaries of network activity. Being deployed at the IP-layer, it uses fixed flow definitions, based on fields of the IP-layer and higher layers. Since several backbone network operators are considering the deployment of (Carrier) Ethernet in

  11. Semi-brittle flow of granitoid fault rocks in experiments

    NARCIS (Netherlands)

    Pec, Matej; Stünitz, Holger; Heilbronner, Renée; Drury, Martyn

    Field studies and seismic data show that semi-brittle flow of fault rocks probably is the dominant deformation mechanism at the base of the seismogenic zone at the so-called frictional-viscous transition. To understand the physical and chemical processes accommodating semi-brittle flow, we have

  12. Design and performance of an experiment for the investigation of open capillary channel flows. Sounding rocket experiment TEXUS-41

    Energy Technology Data Exchange (ETDEWEB)

    Rosendahl, Uwe; Dreyer, Michael E. [University of Bremen, Sounding Rocket Experiment TEXUS-41 Center of Applied Space Technology and Microgravity (ZARM), Bremen (Germany)

    2007-05-15

    In this paper we report on the set-up and the performance of an experiment for the investigation of flow-rate limitations in open capillary channels under low-gravity conditions (microgravity). The channels consist of two parallel plates bounded by free liquid surfaces along the open sides. In the case of steady flow the capillary pressure of the free surface balances the differential pressure between the liquid and the surrounding constant-pressure gas phase. A maximum flow rate is achieved when the adjusted volumetric flow rate exceeds a certain limit leading to a collapse of the free surfaces. The flow is convective (inertia) dominated, since the viscous forces are negligibly small compared to the convective forces. In order to investigate this type of flow an experiment aboard the sounding rocket TEXUS-41 was performed. The aim of the investigation was to achieve the profiles of the free liquid surfaces and to determine the maximum flow rate of the steady flow. For this purpose a new approach to the critical flow condition by enlarging the channel length was applied. The paper is focussed on the technical details of the experiment and gives a review of the set-up, the preparation of the flight procedures and the performance. Additionally the typical appearance of the flow indicated by the surface profiles is presented as a basis for a separate continuative discussion of the experimental results. (orig.)

  13. Study on parallel-channel asymmetry in supercritical flow instability experiment

    International Nuclear Information System (INIS)

    Xiong Ting; Yu Junchong; Yan Xiao; Huang Yanping; Xiao Zejun; Huang Shanfang

    2013-01-01

    Due to the urgent need for experimental study on supercritical water flow instability, the parallel-channel asymmetry which determines the feasibility of such experiments was studied with the experimental and numerical results in parallel dual channel. The evolution of flow rates in the experiments was analyzed, and the steady-state characteristics as well as transient characteristics of the system were obtained by self-developed numerical code. The results show that the asymmetry of the parallel dual channel would reduce the feasibility of experiments. The asymmetry of flow rates is aroused by geometrical asymmetry. Due to the property variation characteristics of supercritical water, the flow rate asymmetry is enlarged while rising beyond the pseudo critical point. The extent of flow rate asymmetry is affected by the bulk temperature and total flow rate; therefore the experimental feasibility can be enhanced by reducing the total flow rate. (authors)

  14. PREFACE: 4th International Conference on Safe Production and Use of Nanomaterials (Nanosafe2014)

    Science.gov (United States)

    Tardif, F.; Damlencourt, J.-F.; Schuster, F.; Gaultier, V.

    2015-05-01

    This volume contains a collection of contributions presented at the 4th International Conference on Safe Production and Use of Nanomaterials (NANOSAFE 2014) held in Grenoble, France, from 18th to 20th November 2014. The issues of fast progress in the field of Nanosafety are up to the potential benefits that nanotechnology can bring to mankind. Making more efficient - more sustainable - easier to share mineral resources, increasing the yields of new energy technologies, enabling drugs that act selectively and locally are just few examples of the wide range of nanomaterial applications that currently benefit humanity. Nevertheless, the dynamic development of nanomaterials requires the adhesion from the general public who rightly demand major progresses in Nanosafety as a prerequisite. This is our exciting responsibility and challenge! Following the successful outcome of the three past international conferences on safe production and use of nanomaterials: Nanosafe 2008, 2010 and 2012, the organizing committee has the pleasure to welcoming you again to Minatec, Grenoble with some of the most famous specialists in the field. This year, two new topics have been added dealing with the "New Application of Nanomaterials" and "Nano-responsible Development" in addition to the usual issues addressed in previous Nanosafe conferences such as Expology, Detection and Characterization, Toxicology, Environmental Interactions, Nanomaterials Release, Life Cycle Analysis, Regulation and Standardization, Risk Management. The debates in 2012 proved highly successful so this formula has been kept in 2014 with 3 round tables: Nano-Responsible Development, Risks and Benefits for the Environment, Toxicology Progress. In this 4th edition, there were more than 330 registered participants from 28 different countries including 160 oral presentation covering the whole Nanosafety issues in 12 sessions, satellite workshops and round tables. This high number of participants makes this edition one of

  15. Climate Change Mitigation in a Sustainable World - Findings of the IPCC 4th Assessment Report

    International Nuclear Information System (INIS)

    Sims, R. E. H.

    2007-01-01

    The 4th Assessment Report on climate change of the Intergovernmental Panel on Climate Change (IPCC, 2007) has recently been completed. The fi rst report in the IPCC 4th Assessment series by Working Group I outlined the latest knowledge on Climate Science. The second by Working Group 2 covered the possibilities for Adaptation of ecosystems, glaciers preceding, sea level rising, droughts etc in various regions. This paper is based on the findings of Working Group III as presented in the recently published report Climate Change 2007: Mitigation of Climate Change. The 27 paragraph Summary for Policy Makers was approved sentence by sentence over 4 days in May 2007 by 120 government delegations in Bangkok, Thailand. The three short Summaries for Policy Makers (SPM), Synthesis report, and the three full reports can be found at www.ipcc.ch. In addition the short Synthesis Report across all three working groups is soon to be released. The report on Mitigation attempted to compile the latest scientific knowledge relating to low-carbon emitting technologies; assessed their costs and potentials for greenhouse gas (GHG) emission avoidance; evaluated their long term prospects out to 2100 for stabilising atmospheric GHGs; provided a detailed list of policy options; and discussed the opportunities for sustainable development and equity linked with GHG abatement. Over the 3 year writing and review process, the author of this paper was the co-ordinating lead author of the writing team for the Working Group III chapter on Energy Supply. Of the 13 chapters, this one received the greatest attention with over 5000 review comments that were each responded to, and with the sections on nuclear and renewable energy receiving a major share of them. Since the 3rd Assessment Report (TAR) was published in 2001, the over-arching message now being delivered by Working Group III is a stronger but positive one: Action is required. The situation is urgent - but not beyond repair. Many energy

  16. Flow Mode Dependent Partitioning Processes of Preferential Flow Dynamics in Unsaturated Fractures - Findings From Analogue Percolation Experiments

    Science.gov (United States)

    Kordilla, J.; Noffz, T.; Dentz, M.; Sauter, M.

    2017-12-01

    To assess the vulnerability of an aquifer system it is of utmost importance to recognize the high potential for a rapid mass transport offered by ow through unsaturated fracture networks. Numerical models have to reproduce complex effects of gravity-driven flow dynamics to generate accurate predictions of flow and transport. However, the non-linear characteristics of free surface flow dynamics and partitioning behaviour at unsaturated fracture intersections often exceed the capacity of classical volume-effective modelling approaches. Laboratory experiments that manage to isolate single aspects of the mass partitioning process can enhance the understanding of underlying dynamics, which ultimately influence travel time distributions on multiple scales. Our analogue fracture network consists of synthetic cubes with dimensions of 20 x 20 x 20 cm creating simple geometries of a single or a cascade of consecutive horizontal fractures. Gravity-driven free surface flow (droplets; rivulets) is established via a high precision multichannel dispenser at flow rates ranging from 1.5 to 4.5 ml/min. Single-inlet experiments show the influence of variable flow rate, atmospheric pressure and temperature on the stability of flow modes and allow to delineate a droplet and rivulet regime. The transition between these regimes exhibits mixed flow characteristics. In addition, multi-inlet setups with constant total infow rates decrease the variance induced by erratic free-surface flow dynamics. We investigate the impacts of variable aperture widths, horizontal offsets of vertical fracture surfaces, and alternating injection methods for both flow regimes. Normalized fracture inflow rates allow to demonstrate and compare the effects of variable geometric features. Firstly, the fracture filling can be described by plug flow. At later stages it transitions into a Washburn-type flow, which we compare to an analytical solution for the case of rivulet flow. Observations show a considerably

  17. The Role of Flow Experience and CAD Tools in Facilitating Creative Behaviours for Architecture Design Students

    Science.gov (United States)

    Dawoud, Husameddin M.; Al-Samarraie, Hosam; Zaqout, Fahed

    2015-01-01

    This study examined the role of flow experience in intellectual activity with an emphasis on the relationship between flow experience and creative behaviour in design using CAD. The study used confluence and psychometric approaches because of their unique abilities to depict a clear image of creative behaviour. A cross-sectional study…

  18. An Examination of Game-Based Learning from Theories of Flow Experience and Cognitive Load

    Science.gov (United States)

    Lai, Chih-Hung; Chu, Chih-Ming; Liu, Hsiang-Hsuan; Yang, Shun-Bo; Chen, Wei-Hsuan

    2013-01-01

    This study aims to discuss whether game-based learning with the integration of games and digital learning could enhance not only the flow experience in learning but achieve the same flow experience in pure games. In addition, the authors discovered that whether the game-based learning could make learners to reveal higher cognitive load. The…

  19. 4th ATLAS Physics Workshop (Athens) - Report from the Physics Sessions

    CERN Multimedia

    Kersevan, B P

    The 4th ATLAS Physics Workshop provided a showcase for studies of some of the most exciting aspects of LHC physics, both within the Standard Model and beyond. It was clear from the wide range of topics covered, from QCD studies to TeV-scale Black Hole production, that preparations are well in hand for understanding whatever Nature, and the LHC, may throw at us. The Standard Model session concentrated on QCD and Electroweak physics, which will form the core of the ATLAS physics program during the first years of LHC operation. Convenor Matt Dobbs began by summarising recent and ongoing studies and pointed out that the first ATLAS papers will aim to prove that we understand LHC physics in the regime where the Standard Model is reliable. Only then will we be able to make convincing claims for the existence of New Physics. Subsequent talks discussed our understanding of this 'bread-and-butter' physics, including minimum bias processes and underlying events (Arthur Moraes), Parton Distribution Functions (Jon Butte...

  20. Effectiveness of fenbendazole against later 4th-stage Strongylus vulgaris in ponies.

    Science.gov (United States)

    Slocombe, J O; McCraw, B M; Pennock, P W; Baird, J D

    1983-12-01

    Twelve pony foals (reared worm-free) were inoculated with Strongylus vulgaris. Approximately 8 weeks later, 4 of the foals were given fenbendazole (10% suspension) at a dosage rate of 10 mg/kg of body weight daily for 5 days and 4 foals were given the suspension at a dosage rate of 50 mg/kg daily for 3 days; the remaining foals were given a placebo. All treatments were administered by stomach tube. Fenbendazole was 99.6 and 97.9% effective in the 2 treatment groups, respectively, in eliminating later 4th-stage S vulgaris larvae located near the origin of major intestinal arteries. On microscopic examination of the ileocolic artery from fenbendazole-treated foals, a few larval remnants were found beneath the tunica intima in small organized mural thrombi overgrown with endothelium. It would appear that larvae are rapidly destroyed after administration of fenbendazole. A pony foal reared on pasture and with arteriographic evidence of arteritis of the cranial mesenteric and ileocolic arteries was treated with fenbendazole (10% suspension) by stomach tube at a dosage rate of 50 mg/kg of body weight daily for 3 days. By arteriographic examination made 4 weeks later, there was evidence of regression of the lesion, and at necropsy done a week later, there was no arteritis or larvae in the lumen of those arteries.

  1. Teaching systems thinking to 4th and 5th graders using Environmental Dashboard display technology.

    Science.gov (United States)

    Clark, Shane; Petersen, John E; Frantz, Cindy M; Roose, Deborah; Ginn, Joel; Rosenberg Daneri, Daniel

    2017-01-01

    Tackling complex environmental challenges requires the capacity to understand how relationships and interactions between parts result in dynamic behavior of whole systems. There has been convincing research that these "systems thinking" skills can be learned. However, there is little research on methods for teaching these skills to children or assessing their impact. The Environmental Dashboard is a technology that uses "sociotechnical" feedback-information feedback designed to affect thought and behavior. Environmental Dashboard (ED) combines real-time information on community resource use with images and words that reflect pro-environmental actions of community members. Prior research indicates that ED supports the development of systems thinking in adults. To assess its impact on children, the technology was installed in a primary school and children were passively exposed to ED displays. This resulted in no measurable impact on systems thinking skills. The next stage of this research examined the impact of actively integrating ED into lessons on electricity in 4th and 5th grade. This active integration enhanced both content-related systems thinking skills and content retention.

  2. A Teaching Model for Scaffolding 4th Grade Students' Scientific Explanation Writing

    Science.gov (United States)

    Yang, Hsiu-Ting; Wang, Kuo-Hua

    2014-08-01

    Improving students scientific explanations is one major goal of science education. Both writing activities and concept mapping are reported as effective strategies for enhancing student learning of science. The purpose of this study was to examine the effect of a teaching model, named the DCI model, which integrates a Descriptive explanation writing activity, Concept mapping, and an Interpretive explanation writing activity, is introduced in a 4th grade science class to see if it would improve students' scientific explanations and understanding. A quasi-experimental design, including a non-randomized comparison group and a pre- and post-test design, was adopted for this study. An experimental group of 25 students were taught using the DCI teaching model, while a comparison group received a traditional lecture teaching. A rubric and content analysis was used to assess students' scientific explanations. The independent sample t test was used to measure difference in conceptual understanding between the two groups, before and after instruction. Then, the paired t test analysis was used to understand the promotion of the DCI teaching model. The results showed that students in the experimental group performed better than students in the comparison group, both in scientific concept understanding and explanation. Suggestions for using concept mapping and writing activities (the DCI teaching model) in science classes are provided in this study.

  3. Proceedings of the 4th annual meeting of Japanese Society of Radiation Safety Management 2005 Kyoto

    International Nuclear Information System (INIS)

    2005-01-01

    This is the program and the proceedings of the 4th annual meeting of Japanese Society of Radiation Safety Management held from November 23rd through the 25th of 2005. The sessions held were: (1) Medical Exposure, (2) Environmental Measurement and Radiation Source Handling, (3) Radiation Measurement and Influence of Electromagnetic Waves, (4) Utilization of Irradiation, (5) Countermeasures against Contamination and Inspection of Contamination, (6) Imaging Plate, (7) Controlled Measurement and Dose Evaluation, (8) Working Environment Measurement 1, (9) Working Environment Measurement 2, (10) Establishment of Software and System, (11) Radiation Education 1, (12) Radiation Education 2, and (13) Exposure Reduction and Safety Control. The poster sessions held were: (1) Exposure Reduction and Radiation Evaluation, (2) Radiation Measurement and Influence of Electromagnetic Waves, (3) Education Training, (4) Safety Control, (5) Software, Data Handling, and Shielding Calculation, and (6) Environmental Radioactivity. The keynote lectures held were: (1) 'Situation of Medical Exposure' and (2) 'Cosmic Radiation While Boarding on Airplanes'. The symposia held were: (1) 'Food Irradiation' and (2) 'Life Science'. (S.K.)

  4. The 4th international comparison on EPR dosimetry with tooth enamel

    Energy Technology Data Exchange (ETDEWEB)

    Fattibene, P., E-mail: paola.fattibene@iss.it [Istituto Superiore di Sanita, Department of Technology and Health, Viale Regina Elena 299, I-00162 Rome (Italy); Wieser, A. [Helmholtz Zentrum Muenchen, Neuherberg D-85764 (Germany); Adolfsson, E. [Linkoeping University, SE-58185 Linkoeping (Sweden); Benevides, L.A. [Naval Dosimetry Center, Bethesda MD 20889-5600 (United States); Brai, M. [University of Palermo, I-90128 Palermo (Italy); Callens, F. [Ghent University, B-9000 Gent (Belgium); Chumak, V. [Research Center for Radiation Medicine AMS, 04050 Kiev (Ukraine); Ciesielski, B. [Medical University of Gdansk, 80-211 Gdansk (Poland); Della Monaca, S. [Istituto Superiore di Sanita, Department of Technology and Health, Viale Regina Elena 299, I-00162 Rome (Italy); Regina Elena Institute, I-00144 Rome (Italy); Emerich, K. [Medical University of Gdansk, 80-211 Gdansk (Poland); Department of Paediatric Dentistry, 80-208 Gdansk (Poland); Gustafsson, H. [Linkoeping University, SE-58185 Linkoeping (Sweden); Hirai, Y. [Radiation Effects Research Foundation, Minami-ku, Hiroshima 732-0815 (Japan); Hoshi, M. [Hiroshima University, Minami-ku, Hiroshima 734-8553 (Japan); Israelsson, A. [Linkoeping University, SE-58185 Linkoeping (Sweden); Ivannikov, A. [Medical Radiological Research Center, Obninsk, Kaluga region (Russian Federation); Ivanov, D. [Institute of Metal Physics, Yekaterinburg 620041 (Russian Federation); Kaminska, J. [Medical University of Gdansk, 80-211 Gdansk (Poland); Ke, Wu [Beijing Institute of Radiation Medicine, Beijing 100850 (China); Lund, E. [Linkoeping University, SE-58185 Linkoeping (Sweden); Marrale, M. [University of Palermo, I-90128 Palermo (Italy)

    2011-09-15

    This paper presents the results of the 4th International Comparison of in vitro electron paramagnetic resonance dosimetry with tooth enamel, where the performance parameters of tooth enamel dosimetry methods were compared among sixteen laboratories from all over the world. The participating laboratories were asked to determine a calibration curve with a set of tooth enamel powder samples provided by the organizers. Nine molar teeth extracted following medical indication from German donors and collected between 1997 and 2007 were prepared and irradiated at the Helmholtz Zentrum Muenchen. Five out of six samples were irradiated at 0.1, 0.2, 0.5, 1.0 and 1.5 Gy air kerma; and one unirradiated sample was kept as control. The doses delivered to the individual samples were unknown to the participants, who were asked to measure each sample nine times, and to report the EPR signal response, the mass of aliquots measured, and the parameters of EPR signal acquisition and signal evaluation. Critical dose and detection limit were calculated by the organizers on the basis of the calibration-curve parameters obtained at every laboratory. For calibration curves obtained by measuring every calibration sample three times, the mean value of the detection limit was 205 mGy, ranging from 56 to 649 mGy. The participants were also invited to provide the signal response and the nominal dose of their current dose calibration curve (wherever available), the critical dose and detection limit of which were also calculated by the organizers.

  5. The 4th ATLAS Physics Workshop in Athens: The discussions, social events, environment, atmosphere, etc.

    CERN Multimedia

    Kawagoe, K

    Over 220 people attended the 4th Atlas Software Workshop in Athens, Greece, a place with a history of thousands of years of scientific achievement. The workshop was hosted by the University of Athens, the National Technical University of Athens, and the Aristotle University of Thessalonki. The venue for the meeting was the newly opened Conference Center of the Physics Department of the University of Athens which featured very comfortable plush red chairs (too comfortable for some of the more jet-lagged workshop participants!). Fig.1. Participants gathering in front of the Conference Center. The workshop schedule was structured to allow plenty of time during breaks for the many lively discussions that developed from the presentations. Ample supplies of coffee, juice, and cookies fueled the discussions. Discussions continued over lunches featuring Greek Salads and other tasty fare. The food was so good that one speaker offered the meal tickets as prize for answering a quiz at the end of her talk! The w...

  6. Continuum Kinetic Plasma Modeling Using a Conservative 4th-Order Method with AMR

    Science.gov (United States)

    Vogman, Genia; Colella, Phillip

    2012-10-01

    When the number of particles in a Debye sphere is large, a plasma can be accurately represented by a distribution function, which can be treated as a continuous incompressible fluid in phase space. In the most general case the evolution of such a distribution function is described by the 6D Boltzmann-Maxwell partial differential equation system. To address the challenges associated with solving a 6D hyperbolic governing equation, a simpler 3D Vlasov-Poisson system is considered. A 4th-order accurate Vlasov-Poisson model has been developed in one spatial and two velocity dimensions. The governing equation is cast in conservation law form and is solved with a finite volume representation. Adaptive mesh refinement (AMR) is used to allow for efficient use of computational resources while maintaining desired levels of resolution. The model employs a flux limiter to remedy non-physical effects such as numerical dispersion. The model is tested on the two-stream, beam-plasma, and Dory-Guest-Harris instabilities. All results are compared with linear theory.

  7. Results of the 4th regular inspection in Unit 1 of the Mihama Nuclear Power Station

    International Nuclear Information System (INIS)

    1981-01-01

    The 4th regular inspection of Unit 1 in the Mihama Nuclear Power Station was made from July, 1975, to December, 1980, on its reactor and associated facilities. The respective stages of inspection during the years are described. The inspection by external appearance examination, disassembling leakage inspection and performance tests indicated crackings in piping for fuel-replacement water tank, the container penetration of recirculation pipe for residual-heat removal, and main steam-relief valve, and leakage in one fuel assembly. Radiation exposure of the personnel during the inspection was less than the permissible dose. Radiation exposure data for the personnel are given in tables. The improvements and repairs done accordingly were as follows: reapir of the piping for a fuel-replacement tank and recirculation piping for residual-heat removal, replacement of the main steam-relief valve, plugging of heating tubes for the steam-generator, replacement of pins and covers for control-rod guide pipes, improvement of safety protection system and installation of rare gas monitor. (J.P.N.)

  8. Phonological Awareness Program: A longitudinal study from Preschool to 4th Grade

    Directory of Open Access Journals (Sweden)

    Ferraz Inês

    2015-01-01

    Full Text Available This study aims to evaluate the effect of phonological awareness training program in preschool performance of 256 children in Funchal, Portugal. This is a longitudinal study from preschool (2005 to 4th grade (2011. It has an experimental design. The sample includes an Experimental Group (132 children and a Control group (124 children. We pretend to answer the following research question: To what degree does training children in phonological awareness as early as preschool have short-term and long-term effects on the evolution of students' competencies and disciplinary knowledge? A first evaluation done in 2006 on the effects of this program at the end of preschool education revealed that the Experimental Group presented significant improvements when compared to the Control Group on the considered dimensions. In 2011, the Experimental Group presented Math National Test higher significant results when compared to the Control Group. The Experimental Group's Portuguese National Test presented better results than the Control Group one, but not significantly. This seems to indicate that Phonological Awareness Program can bring benefits and prevent long-term math school failure.

  9. 4th ASEM Seminar on Knowledge Management to Enhance Nuclear Safety

    International Nuclear Information System (INIS)

    Castello, F.; Reyes, A. de los; Sobari, M. P. Mohd; Istiyanto, J. E.; Faross, P.; Delarosa, A.

    2016-01-01

    Full text: The 4th Asia-Europe Meeting (ASEM) Seminar on Nuclear Safety was convened in Madrid, Spain on 29th–30th October 2015, hosted by the Spanish Nuclear Safety Council. The seminar’s theme was “Knowledge management to enhance nuclear safety”, which aimed to continue discussing on nuclear safety to foster Asia-Europe capacity-building and cooperation in nuclear safety. The seminar was attended by representatives from national governments, nuclear regulators, energy companies, radiation protection and nuclear safety authorities, research institutes and universities. According to such model, proposed by the IAEA, the national capacity building requires an integrated approach based on four pillars: human resources development, education and training, knowledge management and knowledge networking. In this context, Nuclear Knowledge Management (KM) has become a high priority in many countries and international organizations and it has been taken into account to develop and implement specific strategies in ensuring safe and sustainable operation of nuclear facilities. At national level, a sustainable approach should include the necessary Nuclear Knowledge Management actions to ensure that every actor having a significant role in the national nuclear programmes infrastructure acquires, preserves and improves its corporate and individual knowledge. (author

  10. Natural-Scale Lava Flow Experiments on Video: Variations with Temperature, Slope, and Effusion Rate

    Science.gov (United States)

    Karson, J. A.; Wysocki, R.; Edwards, B. R.; Lev, E.

    2013-12-01

    Investigations of active basaltic lava flows and analog materials show that flow dynamics and final flow morphology are strongly determined by the rapidly evolving rheology of the lava crust which constrains the downslope advance of the lava flow. The non-dimensional factor Ψ (ratio of the time scale of crust formation to advective heat loss) provides a useful means of comparing different flows. The key parameters that control Ψ include the melt viscosity, temperature, effusion rate, and slope. Experimental lava flows, up to several meters long created in the Syracuse University Lava Project permit these variables to be investigated independently and in combination in volume-limited flows (Pele), that provide additional information on lava crust development. New, continuous flow (cooling-limited) experiments show downslope variations under constant flow conditions.

  11. Turbulent subcooled boiling flow visualization experiments through a rectangular channel

    International Nuclear Information System (INIS)

    Estrada-Perez, Carlos E.; Dominguez-Ontiveros, Elvis E.; Hassan, Yassin A.

    2008-01-01

    Full text of publication follows: Proper characterization of subcooled boiling flow is of importance in many applications. It is of exceptional significance in the development of empirical models for the design of nuclear reactors, steam generators, and refrigeration systems. Most of these models are based on experimental studies that share the characteristics of utilizing point measurement probes with high temporal resolution, e.g. Hot Film Anemometry (HFA), Laser Doppler Velocimetry (LDV), and Fiber Optic Probes (FOP). However there appears to be a scarcity of experimental studies that can capture instantaneous whole-field measurements with a fast time response. Particle Tracking Velocimetry (PTV) may be used to overcome the limitations associated with point measurement techniques. PTV is a whole-flow-field technique providing instantaneous velocity vectors capable of high spatial and temporal resolution. PTV is also an exceptional tool for the analysis of boiling flow due to its ability to differentiate between the gas and liquid phases and subsequently deliver independent velocity fields associated with each phase. In this work, using PTV, liquid velocity fields of a turbulent subcooled boiling flow in a rectangular channel were successfully obtained. The present results agree with similar studies that used point measurement probes. However, the present study provides additional information; not only averaged profiles of the velocity components were obtained, instantaneous 2-D velocity fields were also readily available with a high temporal and spatial resolution. Analysis of fluctuating velocities, Reynolds stresses, and higher order statistics of the flow are presented. This work is an attempt to enrich the database already collected on turbulent subcooled boiling flow, with the hope that it will be useful in turbulence modeling efforts. (authors)

  12. Intercooler flow path for gas turbines: CFD design and experiments

    Energy Technology Data Exchange (ETDEWEB)

    Agrawal, A.K.; Gollahalli, S.R.; Carter, F.L. [Univ. of Oklahoma, Norman, OK (United States)] [and others

    1995-10-01

    The Advanced Turbine Systems (ATS) program was created by the U.S. Department of Energy to develop ultra-high efficiency, environmentally superior, and cost competitive gas turbine systems for generating electricity. Intercooling or cooling of air between compressor stages is a feature under consideration in advanced cycles for the ATS. Intercooling entails cooling of air between the low pressure (LP) and high pressure (BP) compressor sections of the gas turbine. Lower air temperature entering the HP compressor decreases the air volume flow rate and hence, the compression work. Intercooling also lowers temperature at the HP discharge, thus allowing for more effective use of cooling air in the hot gas flow path. The thermodynamic analyses of gas turbine cycles with modifications such as intercooling, recuperating, and reheating have shown that intercooling is important to achieving high efficiency gas turbines. The gas turbine industry has considerable interest in adopting intercooling to advanced gas turbines of different capacities. This observation is reinforced by the US Navys Intercooled-Recuperative (ICR) gas turbine development program to power the surface ships. In an intercooler system, the air exiting the LP compressor must be decelerated to provide the necessary residence time in the heat exchanger. The cooler air must subsequently be accelerated towards the inlet of the HP compressor. The circumferential flow nonuniformities inevitably introduced by the heat exchanger, if not isolated, could lead to rotating stall in the compressors, and reduce the overall system performance and efficiency. Also, the pressure losses in the intercooler flow path adversely affect the system efficiency and hence, must be minimized. Thus, implementing intercooling requires fluid dynamically efficient flow path with minimum flow nonuniformities and consequent pressure losses.

  13. Vaporizing Flow in Hot Fractures: Observations from Laboratory Experiments

    International Nuclear Information System (INIS)

    Kneafsey, T.; Pruess, K.

    1998-01-01

    Understanding water seepage in hot fractured rock is important in a number of fields including geothermal energy recovery and nuclear waste disposal. Heat-generating high-level nuclear waste packages which will be emplaced in the partially saturated fractured tuffs at the potential high-level nuclear waste repository at Yucca Mountain, Nevada, if it becomes a high-level nuclear waste repository, will cause significant impacts on moisture distribution and migration. Liquid water, which occupies anywhere from 30 to 100% of the porespace, will be vaporized as the temperature reaches the boiling temperature. Flowing primarily in fractures, the vapor will condense where it encounters cooler rock, generating mobile water. This water will flow under gravitational and capillary forces and may flow back to the vicinity of the emplaced waste where it may partially escape vaporization. Water flowing down (sub-) vertical fractures may migrate considerable distances through fractured rock that is at above-boiling temperatures; thus, flowing condensate may contact waste packages, and provide a pathway for the transport of water-soluble radionuclides downward to the saturated zone. Thermally-driven flow processes induced by repository heat may be as important or even more important for repository performance than natural infiltration. For a nominal thermal loading of 57 kW/acre, vaporization may generate an average equivalent percolation flux from condensate of 23.1 mm/yr over 1,000 years, and 5.2 mm/yr over 10,000 years. These numbers are comparable to or larger than current estimates of net infiltration at Yucca Mountain. This condensate, which is generated in the immediate vicinity (meters) of the waste packages, will likely have a larger impact on waste package and repository performance than a similar amount of water introduced at the land surface

  14. Improving Organizational Citizenship Behavior based on Flow Experience

    Directory of Open Access Journals (Sweden)

    Alecxandrina Deaconu

    2016-07-01

    Full Text Available Building on previous research on Organizational Citizenship Behavior (OCB and its influence on the performance of SMEs, this article intends to expand the investigation area to the concept of Flow and its relationship with OCB. In this paper we performed an analysis of the two theoretical constructs, we highlighted similarities and complementarities and we formulated arguments supporting the need to implement strategies that promote a state of flow. Our study points out that through these strategies, employees are encouraged to perform an extra role, beyond their formal duties, which generates an increase of OCB and favorable conditions for sustainable development.

  15. Proposal of experimental setup on boiling two-phase flow on-orbit experiments onboard Japanese experiment module "KIBO"

    Science.gov (United States)

    Baba, S.; Sakai, T.; Sawada, K.; Kubota, C.; Wada, Y.; Shinmoto, Y.; Ohta, H.; Asano, H.; Kawanami, O.; Suzuki, K.; Imai, R.; Kawasaki, H.; Fujii, K.; Takayanagi, M.; Yoda, S.

    2011-12-01

    Boiling is one of the efficient modes of heat transfer due to phase change, and is regarded as promising means to be applied for the thermal management systems handling a large amount of waste heat under high heat flux. However, gravity effects on the two-phase flow phenomena and corresponding heat transfer characteristics have not been clarified in detail. The experiments onboard Japanese Experiment Module "KIBO" in International Space Station on boiling two-phase flow under microgravity conditions are proposed to clarify both of heat transfer and flow characteristics under microgravity conditions. To verify the feasibility of ISS experiments on boiling two-phase flow, the Bread Board Model is assembled and its performance and the function of components installed in a test loop are examined.

  16. Churn-annular foam flow: experiments and modelling

    NARCIS (Netherlands)

    Westende, J.M.C. van 't; Shoeibi Omrani, P.; Vercauteren, F.F.; Nennie, E.D.

    2016-01-01

    Foam assisted lift is a deliquification method in the oil and gas industry, which aims to prevent or postpone countercurrent gas-liquid flow in maturing gas wells or to assist in removing downhole accumulated liquids. The creation of foam reduces the density of the liquid that needs to be

  17. Accuracy of tracer stimulus response experiments in laminar flows

    Czech Academy of Sciences Publication Activity Database

    Chlup, Hynek; Novotný, Pavel; Žitný, R.

    2012-01-01

    Roč. 55, 23-24 (2012), s. 6458-6462 ISSN 0017-9310 Institutional research plan: CEZ:AV0Z20760514 Keywords : residence time distribution * tracer injection * laminar convective dominated flow Subject RIV: JB - Sensors, Measurment, Regulation Impact factor: 2.315, year: 2012 http://www.sciencedirect.com/science/article/pii/S001793101200470X

  18. Exploring Students' Flow Experiences in Business Simulation Games

    Science.gov (United States)

    Buil, I.; Catalán, S.; Martínez, E.

    2018-01-01

    Business simulation games are a motivational and engaging tool for teaching business management. However, relatively little is known about what factors contribute to their success. This study explores the role of flow experienced while using business simulation games. Specifically, this research investigates the influence of challenge, skills,…

  19. Dancing to "groovy" music enhances the experience of flow.

    Science.gov (United States)

    Bernardi, Nicolò F; Bellemare-Pepin, Antoine; Peretz, Isabelle

    2018-05-06

    We investigated whether dancing influences the emotional response to music, compared to when music is listened to in the absence of movement. Forty participants without previous dance training listened to "groovy" and "nongroovy" music excerpts while either dancing or refraining from movement. Participants were also tested while imitating their own dance movements, but in the absence of music as a control condition. Emotion ratings and ratings of flow were collected following each condition. Dance movements were recorded using motion capture. We found that the state of flow was increased specifically during spontaneous dance to groovy excerpts, compared with both still listening and motor imitation. Emotions in the realms of vitality (such as joy and power) and sublimity (such as wonder and nostalgia) were evoked by music in general, whether participants moved or not. Significant correlations were found between the emotional and flow responses to music and whole-body acceleration profiles. Thus, the results highlight a distinct state of flow when dancing, which may be of use to promote well-being and to address certain clinical conditions. © 2018 New York Academy of Sciences.

  20. Relationship of workplace violence and perpetrators on sleep disturbance-data from the 4th Korean working conditions survey.

    Science.gov (United States)

    Yoo, Taejun; Ye, Byeongjin; Kim, Jung-Il; Park, Siwoo

    2016-01-01

    The present study analyzed relationship of workplace violence and perpetrators of violence on sleep disturbance among wage workers in Korea. The present study used data from the 4th Korean Working Conditions Survey (KWCS) of 2014 in selecting a total of 25,138wage workers as the study population, which excluded those who failed or refused to respond to questions required for the present study. The workplace violence experience group included people who satisfied at least one of six relevant criteria (verbal abuse, unwanted sexual attention, threatening or humiliating behavior, physical violence, bullying/harassment, and sexual harassment) and the group was divided according to whether the perpetrator of violence was a client or colleague. Presence of sleep disturbance was determined based on subjective symptoms felt within the past 12 months by each individual. A multiple logistic regression analysis was performed to identify the effects on sleep distance according to general, occupational, and psychosocial characteristics, as well as the types of workplace violence and perpetrators of violence. Workplace violence was found as a factor affecting sleep disturbance (OR = 3.773, 95 % CI = 3.058-4.655), and with respect to perpetrators of violence, complaint of sleep disturbance symptoms was higher when the perpetrator was a colleague or boss (OR = 5.688, 95 % CI 4.189-7.723) than a client (OR = 2.992, 95 % CI 2.301-3.890). Workplace violence had an effect on occurrence of sleep disturbance and when the perpetrators of violence was a boss or colleague at work, the risk for symptoms such as sleep disturbance increased, which indicated the need for appropriate intervention from a workplace healthcare perspective, including preventive education of workplace violence among employees.

  1. EXAMINATION OF EFFECTS OF ARTISTIC GYMNASTICS ON MORPHOLOGICAL CHARACTERISTIC OF 3TH & 4TH GRADE PUPILS OF ELEMENTARY SCHOOLS

    Directory of Open Access Journals (Sweden)

    Vesko Milenković

    2008-08-01

    Full Text Available In this work, the subject of the research is only one segment of the anthropological area, which refers to the appearance of appropriate morphological characteristic. Assessment of the examinees’ morphological characteristics was conducted by the help of 13 anthropometrical measures, chosen according to the International Biologic Program (IBP, in order to cover the four dimensional area defined as longitudinal dimensionality, transversal dimensionality, volume and mass of the body and the subcutaneous fat tissue.During the 2005/06 academic year, a research was conducted so as to determine the effects of current program of physical education teaching on motor abilities flexibility of female pupils. The research involved a total sample of 107 girls from the 3th and 4th grade of elementary school. The subjects were classified in experimental and control groups. The experimental group was made of 59 students and they were practicing according to planning instruction where the artistic gymnastics had the primary part. The control group of 48 students was practicing according to official instructional plan and program for P.E. of the Republic of Serbia. At the beginning of the academic year, initial (first measurement was performed, followed by experimental final (second measurement at the end of experiment. The multi-variant procedures were used in this research ant those were: MANOVA, MANOCOVA and the discriminative analysis. After the experimental treatment, i.e. at the final testing, significant differences were found with female pupils in experimental and control groups concerning the 8 tests for the evaluation of morphological characteristic. The basic conclusion is that the female pupils of experimental group achieved significantly higher teaching effects than the control group, in view of partly increased morphological characteristics, being the result of the effects of the experimental treatment, as well as other external and internal

  2. Summary of the 4th workshop on the reduced-moderation water reactor

    Energy Technology Data Exchange (ETDEWEB)

    Nakatsuka, Toru; Ishikawa, Nobuyuki; Iwamura, Takamichi (eds.) [Japan Atomic Energy Research Inst., Tokai, Ibaraki (Japan). Tokai Research Establishment

    2001-09-01

    The research on Reduced-Moderation Water Reactors (RMWRs) has been performed in JAERI for the development of future innovative reactors. The workshop on the RMWRs has been held every year since fiscal 1997 aimed at information exchange between JAERI and other organizations such as universities, laboratories, utilities and vendors. The 4th workshop was held on March 2, 2001 under the joint auspices of JAERI and North Kanto branch of Atomic Energy Society of Japan. The workshop began with three lectures on recent research activities in JAERI entitled 'Recent Situation of Research on Reduced-Moderation Water Reactor', 'Analysis on Electricity Generation Costs of Reduced Moderation Water Reactors' and 'Reprocessing Technology for Spent Mixed-Oxides Fuel from LWR'. Then five lectures followed: 'Micro Reactor Physics of MOX Fueled LWR' which shows the recent results of reactor physics, Fast Reactor Cooled by Supercritical Light Water' which is another type of reduced-moderation reactor, 'Phase 1 of Feasibility Studies on Commercialized Fast Breeder Reactor Cycle System' mainly conducted by Japan Nuclear Cycle Development Institute (JNC), 'Integral Type Small PWR with Stand-alone Safety' which is intended to suit for the future consumers' needs, and Utilization of Plutonium in Reduced-Moderation Water Reactors' which dictates benefits of plutonium utilization with RMWRs. This report includes the original papers presented at the workshop and summaries of the questions and answers for each lecture, as well as presentation handouts, program and participant list as appendixes. The 8 of the presented papers are indexed individually. (J.P.N.)

  3. 4th International Conference on Energy and Environment 2013 (ICEE 2013)

    Science.gov (United States)

    Chakrabarty, Chandan Kumar; Shamsuddin, Abd Halim Bin; Ahmad, Ibrahim Bin; Desa, Mohamed Nor Bin Mohamed; Din, Norashidah Bte Md; Bte Mohd, Lariyah; Hamid, Nasri A.; See, Ong Hang; Hafiz Nagi, Farrukh; Yong, Lee Choon; Pasupuleti, Jagadeesh; Mei, Goh Su; Abdullah, Fairuz Bin; Satgunam, Meenaloshini

    2013-06-01

    The 4th International Conference on Energy & Environment 2013 (ICEE2013) was organized by the Universiti Tenaga Nasional (UNITEN) to provide a platform for creating and sharing ideas among engineers, researchers, scientists, industrialists and students in sustainable green energy and technologies. The theme 'Shaping a Sustainable Future through Advancement in Green Energy Technology' is in line with the University's vision to be a leading global energy university that shapes a sustainable future. The general scopes of the conference are renewable energy, smart grid, green technology, energy policies and economics, sustainable green energy and environment, sustainable education, international cooperation and innovation and technology transfer. Five international keynote speakers delivered their speeches in specialized areas of green energy technology and sustainability. In addition, the conference highlights several special parallel sessions by notable invited presenters in their niche areas, which are: Hybrid Energy Power Quality & Distributed Energy Smart Grid Nuclear Power & Technologies Geohazard Management Greener Environment for Sustainability Advances in Computational Fluid Dynamics The research papers presented in ICEE2013 are included in this volume of IOP Conference Series: Earth and Environmental Science (EES). EES is abstracted and indexed in SCOPUS, GeoBase, GeoRef, Compendex, Inspec, Chemical Abstracts Service, NASA Astrophysics Data System, and International Nuclear Information System (INIS). With the comprehensive programme outline, the organizing committee hopes that the ICEE2013 was a notable intellectual sharing session for the research and academic community in Malaysia and regionally. The organizing committee expresses gratitude to the ICEE2013 delegates for their great support and contributions to the event.

  4. European Code against Cancer 4th Edition: Ionising and non-ionising radiation and cancer.

    Science.gov (United States)

    McColl, Neil; Auvinen, Anssi; Kesminiene, Ausrele; Espina, Carolina; Erdmann, Friederike; de Vries, Esther; Greinert, Rüdiger; Harrison, John; Schüz, Joachim

    2015-12-01

    Ionising radiation can transfer sufficient energy to ionise molecules, and this can lead to chemical changes, including DNA damage in cells. Key evidence for the carcinogenicity of ionising radiation comes from: follow-up studies of the survivors of the atomic bombings in Japan; other epidemiological studies of groups that have been exposed to radiation from medical, occupational or environmental sources; experimental animal studies; and studies of cellular responses to radiation. Considering exposure to environmental ionising radiation, inhalation of naturally occurring radon is the major source of radiation in the population - in doses orders of magnitude higher than those from nuclear power production or nuclear fallout. Indoor exposure to radon and its decay products is an important cause of lung cancer; radon may cause approximately one in ten lung cancers in Europe. Exposures to radon in buildings can be reduced via a three-step process of identifying those with potentially elevated radon levels, measuring radon levels, and reducing exposure by installation of remediation systems. In the 4th Edition of the European Code against Cancer it is therefore recommended to: "Find out if you are exposed to radiation from naturally high radon levels in your home. Take action to reduce high radon levels". Non-ionising types of radiation (those with insufficient energy to ionise molecules) - including extremely low-frequency electric and magnetic fields as well as radiofrequency electromagnetic fields - are not an established cause of cancer and are therefore not addressed in the recommendations to reduce cancer risk. Copyright © 2015 International Agency for Research on Cancer. Published by Elsevier Ltd. All rights reserved.

  5. Summary of the 4th workshop on the reduced-moderation water reactor

    International Nuclear Information System (INIS)

    Nakatsuka, Toru; Ishikawa, Nobuyuki; Iwamura, Takamichi

    2001-09-01

    The research on Reduced-Moderation Water Reactors (RMWRs) has been performed in JAERI for the development of future innovative reactors. The workshop on the RMWRs has been held every year since fiscal 1997 aimed at information exchange between JAERI and other organizations such as universities, laboratories, utilities and vendors. The 4th workshop was held on March 2, 2001 under the joint auspices of JAERI and North Kanto branch of Atomic Energy Society of Japan. The workshop began with three lectures on recent research activities in JAERI entitled 'Recent Situation of Research on Reduced-Moderation Water Reactor', 'Analysis on Electricity Generation Costs of Reduced Moderation Water Reactors' and 'Reprocessing Technology for Spent Mixed-Oxides Fuel from LWR'. Then five lectures followed: 'Micro Reactor Physics of MOX Fueled LWR' which shows the recent results of reactor physics, Fast Reactor Cooled by Supercritical Light Water' which is another type of reduced-moderation reactor, 'Phase 1 of Feasibility Studies on Commercialized Fast Breeder Reactor Cycle System' mainly conducted by Japan Nuclear Cycle Development Institute (JNC), 'Integral Type Small PWR with Stand-alone Safety' which is intended to suit for the future consumers' needs, and Utilization of Plutonium in Reduced-Moderation Water Reactors' which dictates benefits of plutonium utilization with RMWRs. This report includes the original papers presented at the workshop and summaries of the questions and answers for each lecture, as well as presentation handouts, program and participant list as appendixes. The 8 of the presented papers are indexed individually. (J.P.N.)

  6. Proceedings of the 4th workshop on ion-beam-applied biology

    International Nuclear Information System (INIS)

    Kobayashi, Yasuhiko; Funayama, Tomoo; Wada, Seiichi; Hamada, Nobuyuki

    2005-09-01

    In order to promote research on biological application using ion beam at TIARA, we have annually hold the Workshop on Ion-beam-applied Biology at JAERI Takasaki since 2002. The 4th workshop entitled 'New Frontiers of Biological Research using microbeam - Application to Radio-microsurgery and Cellular Response to Radiations -' was held on June 22nd, 2005, aimed to overview the recent progress in microbeam-applied researches, and discuss the future direction of application of microbeam not to researches in life science and biotechnology, but also to clinical medicine. This workshop was hosted by JAERI Takasaki, with the cooperation of The Ion Beam Breeding Society, The Japan Radiation Research Society, The Japanese Society for Biological Sciences in Space, The Kanto-Kohetsu Branch of The Atomic Energy Society of Japan, and The Japan Radioisotope Association. There were 104 participants including clinicians attended from universities, public research institutions, and private companies. The papers presented in the workshop were about the ion-beam-applied biological researches at JAERI, the present status of microbeam facilities in Japan and foreign countries, and the microbeam-based analyses of damage repair machinery in insects and radiation-induced bystander effects. It was realized again that microbeam is quite useful for functional analyses by targeted disruption of specific tissues in bio-organisms, and is of critical importance in investigating biological influences of low-dose radiations as well as in its radiological application. These researches using microbeam are expected to further march on. The 13 of the presented papers are indexed individually. (J.P.N.)

  7. Support for the 4th Pan-American Congress on Plants and Bioenergy

    Energy Technology Data Exchange (ETDEWEB)

    Carpita, Nicholas C. [Purdue Univ., West Lafayette, IN (United States)

    2016-01-25

    Intellectual Merit: Following the success of the first three Pan-American Congresses on Plants and BioEnergy held biennially, the 4th congress will be held at the University of Guelph, Canada June 4-7, 2014. We aim to continue a tradition of showcasing major advances in energy crop improvement yet keep in perspective the realities of the economic drivers and pressures that govern the translation of scientific success into a commercial success. The congress is endorsed by the American Society of Plant Biologists and the Canadian Society of Plant Biologists. The program will cover a range of disciplines, including algal and plant systems for bioenergy, plant genetics and genomics, gene discovery for improvement of bioenergy production and quality, regulatory mechanisms of synthesis and degradation, strategies for 3rd generation biofuel production and the promise of synthetic biology in production of biofuels and bio-based products, cropping systems and productivity for biomass production, and mitigation of environmental impacts of bioenergy production. Broader Impacts: We are requesting support to generate stipends for domestic and permanent-resident students, post-doctorals, and pre-tenured faculty members to attend and benefit from the outstanding program. The stipends will be limited to registration and on-site lodging costs, with partial support for travel in instances of great need. So that as great a number can benefit as possible, airfare costs will be provided for only applicants with great need. ASPB has endorsed this meeting and will assist in advertising and promoting the meeting. ASPB has a long-standing commitment to increase participation and advance the careers in plant biology of women, minorities and underrepresented scientists, and they will assist us in identifying worthy candidates.

  8. Association of cognitive judgment and shyness with frequency and quality of flow experience

    Directory of Open Access Journals (Sweden)

    Hirao K

    2012-11-01

    Full Text Available Kazuki Hirao, Ryuji Kobayashi, Kenji YabuwakiDepartment of Occupational Therapy, School of Health Science and Social Welfare, Kibi International University, Takahashi City, Okayama, JapanObjective: To determine the association of cognitive judgment and shyness with frequency and quality of flow experience.Design and methods: This was a cross-sectional survey of the relationship between psychological tendency and frequency and quality of flow experience in 68 college students, undertaken in Hiroshima, Japan. The predictors were Shyness Scale scores, measure of ambiguity tolerance scores, and Life Orientation Test scores, and the outcome was the frequency and quality of flow experience.Results: The results of the binary logistic regression analysis indicated that only the measure of ambiguity tolerance (P = 0.02, odds ratio = 1.06, and 95% confidence interval = 1.01–1.11 was a predictor of the quality of flow experience, and only the Shyness Scale (P = 0.007, odds ratio = 0.95, and 95% confidence interval = 0.91–0.98 was a predictor of the frequency of flow experience.Conclusion: The findings suggest that ambiguity tolerance and shyness are associated with the frequency and quality of the flow experience.Keywords: Flow experience, positive psychology, shyness, ambiguity tolerance, life orientation

  9. Generalizing roughness: experiments with flow-oriented roughness

    Science.gov (United States)

    Trevisani, Sebastiano

    2015-04-01

    Surface texture analysis applied to High Resolution Digital Terrain Models (HRDTMs) improves the capability to characterize fine-scale morphology and permits the derivation of useful morphometric indexes. An important indicator to be taken into account in surface texture analysis is surface roughness, which can have a discriminant role in the detection of different geomorphic processes and factors. The evaluation of surface roughness is generally performed considering it as an isotropic surface parameter (e.g., Cavalli, 2008; Grohmann, 2011). However, surface texture has often an anisotropic character, which means that surface roughness could change according to the considered direction. In some applications, for example involving surface flow processes, the anisotropy of roughness should be taken into account (e.g., Trevisani, 2012; Smith, 2014). Accordingly, we test the application of a flow-oriented directional measure of roughness, computed considering surface gravity-driven flow. For the calculation of flow-oriented roughness we use both classical variogram-based roughness (e.g., Herzfeld,1996; Atkinson, 2000) as well as an ad-hoc developed robust modification of variogram (i.e. MAD, Trevisani, 2014). The presented approach, based on a D8 algorithm, shows the potential impact of considering directionality in the calculation of roughness indexes. The use of flow-oriented roughness could improve the definition of effective proxies of impedance to flow. Preliminary results on the integration of directional roughness operators with morphometric-based models, are promising and can be extended to more complex approaches. Atkinson, P.M., Lewis, P., 2000. Geostatistical classification for remote sensing: an introduction. Computers & Geosciences 26, 361-371. Cavalli, M. & Marchi, L. 2008, "Characterization of the surface morphology of an alpine alluvial fan using airborne LiDAR", Natural Hazards and Earth System Science, vol. 8, no. 2, pp. 323-333. Grohmann, C

  10. Critical heat-flux experiments under low-flow conditions in a vertical annulus

    International Nuclear Information System (INIS)

    Mishima, K.; Ishii, M.

    1982-03-01

    An experimental study was performed on critical heat flux (CHF) at low flow conditions for low pressure steam-water upward flow in an annulus. The test section was transparent, therefore, visual observations of dryout as well as various instrumentations were made. The data indicated that a premature CHF occurred due to flow regime transition from churn-turbulent to annular flow. It is shown that the critical heat flux observed in the experiment is essentially similar to a flooding-limited burnout and the critical heat flux can be well reproduced by a nondimensional correlation derived from the previously obtained criterion for flow regime transition. The observed CHF values are much smaller than the standard high quality CHF criteria at low flow, corresponding to the annular flow film dryout. This result is very significant, because the coolability of a heater surface at low flow rates can be drastically reduced by the occurrence of this mode of CHF

  11. Analysis of screeching in a cold flow jet experiment

    Science.gov (United States)

    Wang, M. E.; Slone, R. M., Jr.; Robertson, J. E.; Keefe, L.

    1975-01-01

    The screech phenomenon observed in a one-sixtieth scale model space shuttle test of the solid rocket booster exhaust flow noise has been investigated. A critical review is given of the cold flow test data representative of Space Shuttle launch configurations to define those parameters which contribute to screech generation. An acoustic feedback mechanism is found to be responsible for the generation of screech. A simple equation which permits prediction of screech frequency in terms of basic testing parameters such as the jet exhaust Mach number and the separating distance from nozzle exit to the surface of model launch pad is presented and is found in good agreement with the test data. Finally, techniques are recommended to eliminate or reduce the screech.

  12. Experiments in polydisperse two-phase turbulent flows

    International Nuclear Information System (INIS)

    Bachalo, W.D.; Houser, M.J.

    1985-01-01

    Aspects of turbulent two-phase flow measurements obtained with a laser Doppler velocimeter that was modified to also obtain particle size were investigated. Simultaneous measurements of the particle size and velocity allowed the determination of the lag characteristics of particles over a range of sizes. Relatively large particles were found to respond well to the turbulent fluctuations in low speed flows. Measurements of sprays were obtained at various points throughout the spray plume. Velocity measurements for each drop size class were obtained and revealed the relative velocity relaxation with downstream distance. The evolution of the rms velocities for each size class was also examined. Difficulties associated with seeding polydispersions to obtain gas phase turbulence data were discussed. Several approaches for mitigating the errors due to seed particle concentration bias were reviewed

  13. Fluid mechanics experiments in oscillatory flow. Volume 1: Report

    Science.gov (United States)

    Seume, J.; Friedman, G.; Simon, T. W.

    1992-01-01

    Results of a fluid mechanics measurement program in oscillating flow within a circular duct are presented. The program began with a survey of transition behavior over a range of oscillation frequency and magnitude and continued with a detailed study at a single operating point. Such measurements were made in support of Stirling engine development. Values of three dimensionless parameters, Re(sub max), Re(sub w), and A(sub R), embody the velocity amplitude, frequency of oscillation and mean fluid displacement of the cycle, respectively. Measurements were first made over a range of these parameters which included operating points of all Stirling engines. Next, a case was studied with values of these parameters that are representative of the heat exchanger tubes in the heater section of NASA's Stirling cycle Space Power Research Engine (SPRE). Measurements were taken of the axial and radial components of ensemble-averaged velocity and rms-velocity fluctuation and the dominant Reynolds shear stress, at various radial positions for each of four axial stations. In each run, transition from laminar to turbulent flow, and its reverse, were identified and sufficient data was gathered to propose the transition mechanism. Models of laminar and turbulent boundary layers were used to process the data into wall coordinates and to evaluate skin friction coefficients. Such data aids in validating computational models and is useful in comparing oscillatory flow characteristics to those of fully-developed steady flow. Data were taken with a contoured entry to each end of the test section and with flush square inlets so that the effects of test section inlet geometry on transition and turbulence are documented. Volume 1 contains the text of the report including figures and supporting appendices. Volume 2 contains data reduction program listings and tabulated data (including its graphical presentation).

  14. Fluid mechanics experiments in oscillatory flow. Volume 1

    International Nuclear Information System (INIS)

    Seume, J.; Friedman, G.; Simon, T.W.

    1992-03-01

    Results of a fluid mechanics measurement program is oscillating flow within a circular duct are present. The program began with a survey of transition behavior over a range of oscillation frequency and magnitude and continued with a detailed study at a single operating point. Such measurements were made in support of Stirling engine development. Values of three dimensionless parameters, Re max , Re W , and A R , embody the velocity amplitude, frequency of oscillation and mean fluid displacement of the cycle, respectively. Measurements were first made over a range of these parameters which included operating points of all Stirling engines. Next, a case was studied with values of these parameters that are representative of the heat exchanger tubes in the heater section of NASA's Stirling cycle Space Power Research Engine (SPRE). Measurements were taken of the axial and radical components of ensemble-averaged velocity and rms-velocity fluctuation and the dominant Reynolds shear stress, at various radial positions for each of four axial stations. In each run, transition from laminar to turbulent flow, and in reverse, were identified and sufficient data was gathered to propose the transition mechanism. Models of laminar and turbulent boundary layers were used to process the data into wall coordinates and to evaluate skin friction coefficients. Such data aids in validating computational models and is useful in comparing oscillatory flow characteristics to those of fully-developed steady flow. Data were taken with a contoured entry to each end of the test section and with flush square inlets so that the effects of test section inlet geometry on transition and turbulence are documented. The following is presented in two-volumes. Volume I contains the text of the report including figures and supporting appendices. Volume II contains data reduction program listings and tabulated data (including its graphical presentation)

  15. Flow widening through a Darrieus wind turbine - Theory and experiment

    Science.gov (United States)

    Comolet, R.; Harajli, I.; Mercier Des Rochettes, P.; Yeznasni, A.

    1982-11-01

    A two-dimensional multiple stream tube model is developed for the air flow through a Darrieus wind turbine. The model is configured to account for the widening of the flux tubes as they cross the interior of the actuator disk. Note is made of the lateral broadening of the flow as it moves through the area, leaving a turbulent wake. A relation is defined between the variation in the kinetic energy of the flow and the aerodynamic forces acting on the blades. The global efficiency and the power output of the machine are calculated. Experimental results are reported for a machine equipped with two NACA 0015 blades, each 110 cm long and with a 10 cm chord. The Darrieus had a 1 m diam and was tested in a wind tunnel at wind speeds of 0-18 m/sec. Soap bubbles inflated with He were used for visualization. Power output was found to match prediction. The model is recommended for use in calculating the forces acting on the machine and studying vibration and fatigue causative mechanisms.

  16. Experiments on the Taylor system with an axial flow

    International Nuclear Information System (INIS)

    Tsameret, Avraham.

    1993-02-01

    This work is an experimental study of the Taylor system with a superimposed axial flow. The convective and absolute instability lines which are associated with the propagating Taylor vortices are measured. A quantitative agreement is found with the theoretical predictions. Noise-sustained structures are found to exist in the convectively unstable region, above a critical value of the through flow. These structures are propagating Taylor vortices that are characterized by a noisy power spectrum and irregular temporal dynamics of velocity amplitude. At the absolute instability line the power spectrum of the propagating Taylor vortices exhibits transition to a sharp peak, and the amplitude of the propagating Taylor vortices becomes stationary. The mechanism that generates the noise-sustained structures is identified with a process of permanent amplification of noise that is generated mainly near the inlet boundary. The intrinsic noise in the system is studied. This study is motivated by the question of whether the noise which generates the noise-sustained structures is thermal. The intensity of the intrinsic noise is estimated by several methods, which includes a comparison of data with numerical simulations of the amplitude equation with a noise term. It is found that the intrinsic noise is not thermal, although its intensity reaches the thermal noise level at small through-flow velocities. Novel states are manifested in the system as a result of interaction between the propagating Taylor vortices and spiral modes. These states are studied and their spatial and temporal properties are analyzed. (author)

  17. Research on the flow field of undershot cross-flow water turbines using experiments and numerical analysis

    International Nuclear Information System (INIS)

    Nishi, Y; Inagaki, T; Li, Y; Omiya, R; Hatano, K

    2014-01-01

    The purpose of this research is to develop a water turbine appropriate for low-head open channels in order to effectively utilize the unused hydropower energy of rivers and agricultural waterways. The application of the cross-flow runner to open channels as an undershot water turbine has come under consideration and, to this end, a significant simplification was attained by removing the casings. However, the flow field of undershot cross-flow water turbines possesses free surfaces. This means that with the variation in the rotational speed, the water depth around the runner will change and flow field itself is significantly altered. Thus it is necessary to clearly understand the flow fields with free surfaces in order to improve the performance of this turbine. In this research, the performance of this turbine and the flow field were studied through experiments and numerical analysis. The experimental results on the performance of this turbine and the flow field were consistent with the numerical analysis. In addition, the inlet and outlet regions at the first and second stages of this water turbine were clarified

  18. Intuitional experiment and numerical analysis of flow characteristics affected by flow accelerated corrosion in elbow pipe system

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Hyung Joon [School of Mechanical and Aerospace Engineering, Seoul National University, Gwanak-gu, Seoul 151-744 (Korea, Republic of); Kim, Kyung Hoon, E-mail: kimkh@khu.ac.kr [Department of Mechanical Engineering, Kyung Hee University, Seochun 1, Yongin, Gyeonggi 446-701 (Korea, Republic of)

    2016-05-15

    Highlights: • Wall-thinning erosion of pipelines in plants leads to fatal accidents unexpectedly. • Flow Acceleration Corrosion (FAC) is a main reason of wall-thinning. • For industrial safety, it is necessary to verify the tendency of FAC. • We focused on local wall thinning by FAC with intuitional visualization experiment and numerical analysis in elbow pipe.

  19. CFD Validation with a Multi-Block Experiment to Evaluate the Core Bypass Flow in VHTR

    International Nuclear Information System (INIS)

    Yoon, Su Jong; Lee, Jeong Hun; Park, Goon Cherl; Kim, Min Hwan

    2010-01-01

    Core bypass flow of Very High Temperature Reactor (VHTR) is defined as the ineffective coolant which passes through the bypass gaps between the block columns and the crossflow gaps between the stacked blocks. This flows lead to the variation of the flow distribution in the core and affect the core thermal margin and the safety of VHTR. Therefore, bypass flow should be investigated and quantified. However, it is not a simple question, because the flow path of VHTR core is very complex. In particular, since dimensions of the bypass gap and the crossflow gap are of the order of few millimeters, it is very difficult to measure and to analyze the flow field at those gaps. Seoul National University (SNU) multi-block experiment was carried out to evaluate the bypass flow distribution and the flow characteristics. The coolant flow rate through outlet of each block column was measured, but the local flow field was measured restrictively in the experiment. Instead, CFD analysis was carried out to investigate the local phenomena of the experiment. A commercial CFD code CFX-12 was validated by comparing the simulation results and the experimental data

  20. 75 FR 38718 - Safety Zone; Sault Sainte Marie 4th of July Fireworks, St. Mary's River, Sault Sainte Marie, MI

    Science.gov (United States)

    2010-07-06

    ... temporary safety zone on the St. Mary's River, Sault Sainte Marie, Michigan. This zone is intended to..., St. Mary's River, Sault Sainte Marie, MI (a) Location. The following area is a temporary safety zone...-AA00 Safety Zone; Sault Sainte Marie 4th of July Fireworks, St. Mary's River, Sault Sainte Marie, MI...

  1. Proceedings of the International Conference on Educational Data Mining (EDM) (4th, Eindhoven, the Netherlands, July 6-8, 2011)

    Science.gov (United States)

    Pechenizkiy, Mykola; Calders, Toon; Conati, Cristina; Ventura, Sebastian; Romero, Cristobal; Stamper, John

    2011-01-01

    The 4th International Conference on Educational Data Mining (EDM 2011) brings together researchers from computer science, education, psychology, psychometrics, and statistics to analyze large datasets to answer educational research questions. The conference, held in Eindhoven, The Netherlands, July 6-9, 2011, follows the three previous editions…

  2. Analysis of Lexical Quality and Its Relation to Writing Quality for 4th Grade, Primary School Students in Chile

    Science.gov (United States)

    Gómez Vera, Gabriela; Sotomayor, Carmen; Bedwell, Percy; Domínguez, Ana María; Jéldrez, Elvira

    2016-01-01

    Few studies have addressed vocabulary quality in developing writing skill in Spanish. Even less addressed it within the Chilean educational system. The specific objective of this study was to characterize, using a comprehensive set of indicators, the quality of the vocabulary produced by Chilean 4th grade students. Based on a national writing…

  3. Widely Tunable 4th Order Switched Gm -C Band-Pass Filter Based on N-Path Filters

    NARCIS (Netherlands)

    Darvishi, M.; van der Zee, Ronan A.R.; Klumperink, Eric A.M.; Nauta, Bram

    2012-01-01

    Abstract—A widely tunable 4th order BPF based on the subtraction of two 2nd order 4-path passive-mixer filters with slightly different center frequencies is proposed. The center frequency of each 4-path filter is slightly shifted relative to its clock frequency (one upward and the other one

  4. Investigation of solutions of boundary-value singular perturbated problem for Schroedinger equation of 4th order

    International Nuclear Information System (INIS)

    Amirkhanov, I.V.; Zhidkov, E.P.; Konnova, S.V.

    2000-01-01

    For the case of spherical-symmetrical potential we have considered the convergence of the solution of singular-perturbated Schroedinger equation of the 4th order to the solution of the corresponding standard nonrelativistic Schroedinger equation by numerical and analytical methods. The questions of existence of the solutions are explored. Numerical results are given. (author)

  5. Using Inquiry-Based Instruction to Teach Research Methods to 4th-Grade Students in an Urban Setting

    Science.gov (United States)

    Hamm, Ellen M.; Cullen, Rebecca; Ciaravino, Melissa

    2013-01-01

    When a college professor who teaches research methods to graduate education students was approached by a local public urban elementary school to help them teach research skills to 4th-graders, it was thought that the process would be simple--take what we did at the college level and differentiate it for the childhood classroom. This article will…

  6. Effect of the SQ4R Technique on the Reading Comprehension of Elementary School 4th Grade Elementary School Students

    Science.gov (United States)

    Basar, Murat; Gürbüz, Mehmet

    2017-01-01

    The aim of this study is to examine the effect of SQ4R (Survey, Question, Read, Reflect, Recite, Review) technique of the reading comprehension ability of elementary school 4th grade students. The sampling was constituted by 57 students from two different branches of the Ataturk Elementary School in the center of Usak region during the 2nd…

  7. Novelly formed products of the interaction of fuel with construction materials of the 4th unit of Chernobyl NPP

    International Nuclear Information System (INIS)

    Borovoj, A.A.; Galkin, B.Ya.; Krinitsyn, A.P.; Pazukhin, Eh.M.; Kheruvimov, A.N.; Chechcherov, K.P.; Anderson, E.B.

    1991-01-01

    Radiation environment and map of sampling route in the steam distributing collector of the 4th unit of the Chernobyl NPP are described. The results of gamma- and alpha radiometric analyses as well as chemical analysis are presented. Samples of core materials taken from the depth of fuel-containing masses by drilling through reactor vault wall of the damaged power unit are described

  8. Native American Students' Understanding of Geologic Time Scale: 4th-8th Grade Ojibwe Students' Understanding of Earth's Geologic History

    Science.gov (United States)

    Nam, Younkyeong; Karahan, Engin; Roehrig, Gillian

    2016-01-01

    Geologic time scale is a very important concept for understanding long-term earth system events such as climate change. This study examines forty-three 4th-8th grade Native American--particularly Ojibwe tribe--students' understanding of relative ordering and absolute time of Earth's significant geological and biological events. This study also…

  9. An Evaluation of Factors Affecting Decision Making among 4th Grade Elementary School Students with Low Socio-Economic Status

    Science.gov (United States)

    Kaskaya, Alper; Calp, Sükran; Kuru, Oguzhan

    2017-01-01

    Decision making is one of the most important life skills. While making correct, timely, accurate and appropriate decisions lead to positive changes in one's life, making incorrect decisions may have a negative impact. It is an important issue to examine what the 4th grade students in primary school have about the decision-making ability to be…

  10. 76 FR 72957 - 4th Annual Trauma Spectrum Conference: Bridging the Gap Between Research and Clinical Practice of...

    Science.gov (United States)

    2011-11-28

    ... Conference: Bridging the Gap Between Research and Clinical Practice of Psychological Health and Traumatic... is hereby given of the ``4th Annual Trauma Spectrum Conference: Bridging the Gap Between Research and... Health (NIH), Bethesda, Maryland. This year's event focuses on bridging the gap between research and...

  11. Investigation of Academic Success, Self-Esteem and Academic Self-Concept in 4th Class Primary School Students

    Science.gov (United States)

    Çetinkaya, Seher

    2017-01-01

    In Turkey due to changes in the age starting school implemented during the 2012-2013 academic year, children ages from 60 months to 84 months were subject to the same educational program in the same class. By the 2015-2016 academic year these children were at the end of 4th class. This research aimed to investigate the Turkish and mathematic…

  12. Communicating Science to Impact Learning? A Phenomenological Inquiry into 4th and 5th Graders' Perceptions of Science Information Sources

    Science.gov (United States)

    Gelmez Burakgazi, Sevinc; Yildirim, Ali; Weeth Feinstein, Noah

    2016-01-01

    Rooted in science education and science communication studies, this study examines 4th and 5th grade students' perceptions of science information sources (SIS) and their use in communicating science to students. It combines situated learning theory with uses and gratifications theory in a qualitative phenomenological analysis. Data were gathered…

  13. An Exploration of Transition Experiences Shaping Student Veteran Life Flow

    Science.gov (United States)

    Gregg, Brian Tuan

    2016-01-01

    Educational institutions offer transformative opportunities for veterans transitioning from military service. Veteran-specific cultural supports in educational environments offer participation in occupations and development of skills needed to complete educational goals. However, veterans experience complex life circumstances atypical from…

  14. Laboratory experiments on heat-drive two-phase flows in natural and artificial rock fractures

    International Nuclear Information System (INIS)

    Kneafsey, Timothy J.; Pruess, Karsten

    1998-01-01

    Water flow in partially saturated fractures under thermal drive may lead to fast flow along preferential localized pathways and heat pipe conditions. At the potential high-level nuclear waste repository at Yucca Mountain, water flowing in fast pathways may ultimately contact waste packages and transport radionuclides to the accessible environment. Sixteen experiments were conducted to visualize heat-driven liquid flow in fracture models that included (1) assemblies of roughened glass plates, (2) epoxy replicas of rock fractures, and (3) a fractured specimen of Topopah Spring tuff. Continuous rivulet flow was observed for high liquid flow rates, intermittent rivulet flow and drop flow for intermediate flow rates, and film flow for lower flow rates and wide apertures. Heat pipe conditions (vapor-liquid counterflow with phase change) were identified in five of the seven experiments in which spatially resolved thermal monitoring was performed but not when vapor-liquid counterflow was hindered by very narrow apertures and when an inadequate working fluid volume was used

  15. Buoyant miscible displacement flow of shear-thinning fluids: Experiments and Simulations

    Science.gov (United States)

    Ale Etrati Khosroshahi, Seyed Ali; Frigaard, Ian

    2017-11-01

    We study displacement flow of two miscible fluids with density and viscosity contrast in an inclined pipe. Our focus is mainly on displacements where transverse mixing is not significant and thus a two-layer, stratified flow develops. Our experiments are carried out in a long pipe, covering a wide range of flow-rates, inclination angles and viscosity ratios. Density and viscosity contrasts are achieved by adding Glycerol and Xanthan gum to water, respectively. At each angle, flow rate and viscosity ratio are varied and density contrast is fixed. We identify and map different flow regimes, instabilities and front dynamics based on Fr , Re / Frcosβ and viscosity ratio m. The problem is also studied numerically to get a better insight into the flow structure and shear-thinning effects. Numerical simulations are completed using OpenFOAM in both pipe and channel geometries and are compared against the experiments. Schlumberger, NSERC.

  16. Thermal experiments with LMFBR subassembly models in sodium flow

    International Nuclear Information System (INIS)

    Moeller, R.; Tschoeke, H.

    1982-01-01

    Within the framework of the Fast Breeder Project research work has been undertaken at the Karlsruhe Nuclear Research Center on the thermal and fluid dynamics of nominal and distorted core subassemblies. In 19-rod bundle models (P/D=1.30, W/R=1.38) three-dimensional temperature distributions were measured in the cladding tubes exposed to sodium flow. Results of measurements of the azimuthal temperature profiles of rotated rods in the duct wall zone are indicated for different operating conditions 80 2 , evenly distributed load and oblique load; different axial positions of the spacer grids; and different positions of one bowed rod

  17. Outcomes following surgical repair using layered closure of unrepaired 4th degree perineal tear in rural western Uganda.

    Science.gov (United States)

    Goh, Judith T W; Tan, Stephanie B M; Natukunda, Harriet; Singasi, Isaac; Krause, Hannah G

    2016-11-01

    In many rural low-income countries, perineal tears at time of vaginal birth are not repaired at time of delivery. The aims of this study are to describe the surgical technique for management of the unrepaired 4th degree tear, performed without flaps, and short-term follow up on anal incontinence symptoms using a validated questionnaire. Women presenting to fistula camps in western Uganda with unrepaired 4th degree tears were interviewed using the Cleveland Clinic Continence Score. Interviews were undertaken pre-operatively, at 4-6 weeks post-operatively and 12 months following surgery. Repair of the 4th degree tear was performed in layers, with an overlapping anal sphincter repair and reconstruction of the perineal body, without flaps. All women were examined prior to discharge. 68 women completed pre-operative Cleveland Clinic Continence Scores. Prior to surgery, 59 % of women complained of daily incontinence to solid stools. Over 70 % of women complained of restriction to lifestyle due to the unrepaired 4th degree tear. About 50 % of the women are rejected by their husbands because of the condition. Only 1 woman had wound breakdown on Day 2. At 4 to 6 weeks follow-up, 61 women were contacted and all reported perfect continence. This study highlights the hidden problem of unrepaired 4th degree tears in rural areas of low-income countries where most deliveries are undertaken in the village without professional health care workers. These tears have significant impact on quality of life and anal incontinence. Short-term outcomes following surgical repair using a layered closure are promising.

  18. FOREWORD: 4th International Workshop on New Computational Methods for Inverse Problems (NCMIP2014)

    Science.gov (United States)

    2014-10-01

    This volume of Journal of Physics: Conference Series is dedicated to the scientific contributions presented during the 4th International Workshop on New Computational Methods for Inverse Problems, NCMIP 2014 (http://www.farman.ens-cachan.fr/NCMIP_2014.html). This workshop took place at Ecole Normale Supérieure de Cachan, on May 23, 2014. The prior editions of NCMIP also took place in Cachan, France, firstly within the scope of ValueTools Conference, in May 2011 (http://www.ncmip.org/2011/), and secondly at the initiative of Institut Farman, in May 2012 and May 2013, (http://www.farman.ens-cachan.fr/NCMIP_2012.html), (http://www.farman.ens-cachan.fr/NCMIP_2013.html). The New Computational Methods for Inverse Problems (NCMIP) Workshop focused on recent advances in the resolution of inverse problems. Indeed, inverse problems appear in numerous scientific areas such as geophysics, biological and medical imaging, material and structure characterization, electrical, mechanical and civil engineering, and finances. The resolution of inverse problems consists of estimating the parameters of the observed system or structure from data collected by an instrumental sensing or imaging device. Its success firstly requires the collection of relevant observation data. It also requires accurate models describing the physical interactions between the instrumental device and the observed system, as well as the intrinsic properties of the solution itself. Finally, it requires the design of robust, accurate and efficient inversion algorithms. Advanced sensor arrays and imaging devices provide high rate and high volume data; in this context, the efficient resolution of the inverse problem requires the joint development of new models and inversion methods, taking computational and implementation aspects into account. During this one-day workshop, researchers had the opportunity to bring to light and share new techniques and results in the field of inverse problems. The topics of the

  19. Fluid mechanics experiments in oscillatory flow. Volume 2: Tabulated data

    Science.gov (United States)

    Seume, J.; Friedman, G.; Simon, T. W.

    1992-01-01

    Results of a fluid mechanics measurement program in oscillating flow within a circular duct are presented. The program began with a survey of transition behavior over a range of oscillation frequency and magnitude and continued with a detailed study at a single operating point. Such measurements were made in support of Stirling engine development. Values of three dimensionless parameters, Re sub max, Re sub w, and A sub R, embody the velocity amplitude, frequency of oscillation, and mean fluid displacement of the cycle, respectively. Measurements were first made over a range of these parameters that are representative of the heat exchanger tubes in the heater section of NASA's Stirling cycle Space Power Research Engine (SPRE). Measurements were taken of the axial and radial components of ensemble-averaged velocity and rms velocity fluctuation and the dominant Reynolds shear stress, at various radial positions for each of four axial stations. In each run, transition from laminar to turbulent flow, and its reverse, were identified and sufficient data was gathered to propose the transition mechanism. Volume 2 contains data reduction program listings and tabulated data (including its graphics).

  20. A Stopped-Flow Kinetics Experiment for the Physical Chemistry Laboratory Using Noncorrosive Reagents

    Science.gov (United States)

    Prigodich, Richard V.

    2014-01-01

    Stopped-flow kinetics techniques are important to the study of rapid chemical and biochemical reactions. Incorporation of a stopped-flow kinetics experiment into the physical chemistry laboratory curriculum would therefore be an instructive addition. However, the usual reactions studied in such exercises employ a corrosive reagent that can over…

  1. Quantitative modelling of HDPE spurt experiments using wall slip and generalised Newtonian flow

    NARCIS (Netherlands)

    Doelder, den C.F.J.; Koopmans, R.J.; Molenaar, J.

    1998-01-01

    A quantitative model to describe capillary rheometer experiments is presented. The model can generate ‘two-branched' discontinuous flow curves and the associated pressure oscillations. Polymer compressibility in the barrel, incompressible axisymmetric generalised Newtonian flow in the die, and a

  2. The Relationship of Motivation and Flow Experience to Academic Procrastination in University Students

    Science.gov (United States)

    Lee, Eunju

    2005-01-01

    In this article, the author examined the relationships of motivation and flow experience to academic procrastination in 262 Korean undergraduate students who completed a questionnaire on procrastination, flow, and motivation. The results indicated that high procrastination was associated with lack of self-determined motivation and low incidence of…

  3. Multichannel readout ASIC design flow for high energy physics and cosmic rays experiments

    International Nuclear Information System (INIS)

    Voronin, A; Malankin, E

    2016-01-01

    In the large-scale high energy physics and astrophysics experiments multi-channel readout application specific integrated circuits (ASICs) are widely used. The ASICs for such experiments are complicated systems, which usually include both analog and digital building blocks. The complexity and large number of channels in such ASICs require the proper methodological approach to their design. The paper represents the mixed-signal design flow of the ASICs for high energy physics and cosmic rays experiments. This flow was successfully embedded to the development of the read-out ASIC prototype for the muon chambers of the CBM experiment. The approach was approved in UMC CMOS MMRF 180 nm process. The design flow enable to analyse the mixed-signal system operation on the different levels: functional, behavioural, schematic and post layout including parasitic elements. The proposed design flow allows reducing the simulation period and eliminating the functionality mismatches on the very early stage of the design. (paper)

  4. Turbulence Models: Data from Other Experiments: FAITH Hill 3-D Separated Flow

    Data.gov (United States)

    National Aeronautics and Space Administration — Exp: FAITH Hill 3-D Separated Flow. This web page provides data from experiments that may be useful for the validation of turbulence models. This resource is...

  5. The Place and Importance of Values Education in 4.th and 5th. Grade Primary School Social Studies Textbooks

    Directory of Open Access Journals (Sweden)

    Mehmet Fatih Yiğit

    2013-11-01

    varied beginning from 1970s. Superka and his colleagues (1976 argue that there are five basic approaches to values education: inculcation, moral development, analysis, values clarification and action learning. On the other hand, Sunal and Haas (2002 identified three approaches to values education: values clarification, value analysis and character education. While discussing the basic processes and principles of values education, we claim that values education should not be given only as theoretical knowledge. If the students are not supported with real-life examples and experiences, theoretical information will result in reducing the interest in values education. It is also stated that using concrete terms, instead of abstract ones, will help primary school children to get the idea more effectively. We also mention the limitation of rewarding a student for his/her good manners and actions. At this point, we analyzed several studies conducted in this area and found that rewarding a student too much will result in undermining the sense of helpfulness (Batson, et al., 1978 and hindering intrinsic motivation (Kohn, 1993; Deci&Ryan, 1985. Other basic processes and principles of values education discussed in this study are; the role of teachers in values education, group study for effective values education, promoting reasoning and logic while developing empathy, the role of self-esteem, and developing the sense of ‘us’ instead of ‘me’. Content analysis was conducted to collect data from the 2004 Social Studies program published by Ministry of Education and the 4th and 5th grade Social Studies textbooks. The researchers identified the frequencies of words and references regarding values and then categorized them to provide a meaningful content. After creating the coding frames, collected data was gathered under the relevant codes. Five main characteristic features of values are defined in the 2004 Social Studies 4th and 5th grade program. Those are: 1- Values are

  6. Flow characteristics of centrifugal gas-liquid separator. Investigation with air-water two-phase flow experiment

    International Nuclear Information System (INIS)

    Yoneda, Kimitoshi; Inada, Fumio

    2004-01-01

    Air-water two-phase flow experiment was conducted to examine the basic flow characteristics of a centrifugal gas-liquid separator. Vertical transparent test section, which is 4 m in height, was used to imitate the scale of a BWR separator. Flow rate conditions of gas and liquid were fixed at 0.1 m 3 /s and 0.033 m 3 /s, respectively. Radial distributions of two-phase flow characteristics, such as void fraction, gas velocity and bubble chord length, were measured by traversing dual optical void probes in the test section, horizontally. The flow in the standpipe reached to quasi-developed state within the height-to-diameter aspect ratio H/D=10, which in turn can mean the maximum value for an ideal height design of a standpipe. The liquid film in the barrel showed a maximum thickness at 0.5 to 1 m in height from the swirler exit, which was a common result for three different standpipe length conditions, qualitatively and quantitatively. The empirical database obtained in this study would contribute practically to the validation of numerical analyses for an actual separator in a plant, and would also be academically useful for further investigations of two-phase flow in large-diameter pipes. (author)

  7. Flow experience in game based learning – a systematic literature review

    Directory of Open Access Journals (Sweden)

    Arttu Perttula

    2017-03-01

    Full Text Available The entertaining elements implemented in a serious game are key factors in determining whether a player will be engaged in a play-learn process and able to achieve the desired learning outcomes. Thus, optimization of subjective playing experience is a crucial part of a game design process. Flow theory can be adopted for measuring user experience and analyzing the quality of serious game designs. In addition, flow seems to have a positive influence on performance enhancement, learning and engagement. The focus of this review is especially on examining the meaning of flow in the context of serious games as well as exploring the relationship between flow and learning, factors that influence occurrence of flow and how flow is operationalized. The review revealed that there are mainly conceptual considerations about flow in serious games, but no robust empirical evidence about the meaning of flow. This is in line with other studies. We argue that research on flow should focus on the specific aspects related to the very nature of serious games that combine enjoyment and learning. Furthermore, new methods to measure flow and analyse the data need to be developed and studied.

  8. Size variation and flow experience of physical game support objects

    NARCIS (Netherlands)

    Feijs, L.M.G.; Peters, P.J.F.; Eggen, J.H.

    2004-01-01

    This paper is about designing and evaluating an innovative type of computer game. Game support objects are used to enrich the gaming experience [7]. The added objects are active but are simpler than real robots. In the study reported here they are four helper ghosts connected to a traditional Pacman

  9. Interpretation of field experiments on the flow of water and tracers through crystalline rock

    International Nuclear Information System (INIS)

    Hodgkinson, D.P.; Lever, D.A.; Robinson, P.C.; Bourke, P.J.

    1983-01-01

    This paper reviews recent work at Harwell on the interpretation of field experiments on the flow of water and tracers through crystalline rock. First a model for the radial transport of tracers through an isolated fracture is outlined and used to analyse a recent Swedish experiment at Finnsjoen. Secondly, the theoretical and experimental approach that is being used to quantify flow and dispersion through networks of fractures is described

  10. International Symposium on Stratified Flows (4th) Held in Grenoble, France on June 29-July 2, 1994. Volume 4

    Science.gov (United States)

    1994-10-10

    which also involve bacteria, is quite complex and web -like and therefore often denoted the food web . There is an extremely great manifold of living and...Dr S.B. Dalziel for their helpful suggestions and comnuents, 6 References AMEN, It. & MAXWOrTIIY T. 1980 The gravitational collapse of a wixed region

  11. International Symposium on Stratified Flows (4th) Held in Grenoble, France on June 29-July 2, 1994. Volume 3

    Science.gov (United States)

    1994-10-10

    support plant and animal life . The ocean is stably stratified, which acts to inhibit vertical mixing. Munk (1966) has show that a basin-averaged...fall int a range specified batwoexi L,., wid Lr.+Ad. For each individual profile which contains uiversions , r𔃽q.2 can be used to obtain the empirical

  12. International Symposium on Stratified Flows (4th) Held in Grenoble, France on June 29-July 2, 1994. Volume 2

    Science.gov (United States)

    1994-10-10

    the thermometric expanesivity. Moreover, the Prandtl number is assumed to be equal to one. The fluctuating velocity fieldu, the pressure fi ld p, and...vortex motion. Aluminlum powder and kalliroscope particles were used in this case. The aluminium particle are almost isotropic and move together with...suspending aluminium particles in the salt water and then slit lighting the tank from the side. Photographs were taken with a 35mm camera with exposure time

  13. An efficient continuous flow helium cooling unit for Moessbauer experiments

    International Nuclear Information System (INIS)

    Herbert, I.R.; Campbell, S.J.

    1976-01-01

    A Moessbauer continuous flow cooling unit for use with liquid helium over the temperature range 4.2 to 300K is described. The cooling unit can be used for either absorber or source studies in the horizontal plane and it is positioned directly on top of a helium storage vessel. The helium transfer line forms an integral part of the cooling unit and feeds directly into the storage vessel so that helium losses are kept to the minimum. The helium consumption is 0.12 l h -1 at 4.2 K decreasing to 0.055 l h -1 at 40 K. The unit is top loading and the exchange gas cooled samples can be changed easily and quickly. (author)

  14. First Experiments with the Simulation of Particulate Flows

    Energy Technology Data Exchange (ETDEWEB)

    Uhlmann, M.

    2003-07-01

    Several variants of a Eulerian-Lagrangian method for the simulation of particulate flows are implemented in a finite-difference framework. All methods have in common that they represent the presence of the solid fraction by means of artificial volume forces in the momentum equation of the fluid phase. Thereby, explicit griddling of the moving particles is avoided and a fixed grid can be used. The computations show that the direct forcing method (Kin et a/., 2001) is not adequate for a our purposes due to large oscillations in the hydro-dynamical forces. The immersed method of Pekin (2002) does provide accurate predictions of particle motion,however at the cost of a small time step. (Author) 33 refs.

  15. First Experiments with the Simulation of Particulate Flows

    International Nuclear Information System (INIS)

    Uhlmann, M.

    2003-01-01

    Several variants of a Eulerian-Lagrangian method for the simulation of particulate flows are implemented in a finite-difference framework. All methods have in common that they represent the presence of the solid fraction by means of artificial volume forces in the momentum equation of the fluid phase. Thereby, explicit griddling of the moving particles is avoided and a fixed grid can be used. The computations show that the direct forcing method (Kin et a/., 2001) is not adequate for a our purposes due to large oscillations in the hydro-dynamical forces. The immersed method of Pekin (2002) does provide accurate predictions of particle motion,however at the cost of a small time step. (Author) 33 refs

  16. Relationships between Flow Experience, Life Meaningfulness and Subjective Well-being in Music Students

    Directory of Open Access Journals (Sweden)

    Martin Sedlár

    2014-01-01

    Full Text Available The study examines relationships between flow experience in musical activities, life meaningfulness and subjective well – being. Life meaningfulness belongs to eudaimonic good life, subjective well–being belongs to hedonic good life and flow seems to be combination of both approaches. It is supposed that flow experience in musical activity and life meaningfulness should have positive impact on subjective well –being. The research sample consisted of 96 university music students (37 males, 59 females from the Music and Dance Faculty, Academy of Performing Arts in Bratislava, Slovakia. Dispositional Flow Scale–2, which measures nine dimension of flow, was used for measuring frequency o f flow experience. Life Meaningfulness Scale, which measures three dimensions of life meaningfulness, was used for measuring meaningfulness of life. Positive and Negative Affect Schedule measured affective components of subjective well–being, and Satisfaction with Life Scale measured cognitive component of subjective well–being. Categorization revealed that the most favourite performing musical activities are creative musical activities, such as reproduction and production, during which music students relatively often experience flow. The results of correlation analysis showed that total scores of flow experience, life meaningfulness and components of subjective well–being, significantly correlate each other. Aspects of flow, clear goals and autotelic experience are positively related to cognitive and motivational dimension of life meaningfulness and also to positive affectivity. Loss of self–consciousness and autotelic experience are positively related to emotional dimension of life meaningfulness. Challenge–skill balance, action–awareness merging, clear goals, concentration on task at hand, sense of control and autotelic experience are negatively related to negative affectivity. Challenge–skill balance and autotelic experience are related to

  17. Investigation and mitigation of condensation induced water hammer by stratified flow experiments

    Science.gov (United States)

    Kadakia, Hiral J.

    This research primarily focuses on the possibility of using stratified flow in preventing an occurrence of condensation induced water hammer (CIWH) in horizontal pipe involving steam and subcooled water. A two-phase flow loop simulating the passive safety systems of an advanced light water reactor was constructed and a series of stratified flow experiments were carried out involving a system of subcooled water, saturated water, and steam. Special instruments were designed to measure steam flow rate and subcooled liquid velocity. These experiments showed that when flow field conditions meet certain criteria CIWH does occur. Flow conditions used in experiments were typically observed in passive safety systems of an advanced light water cooled reactor. This research summarizes a) literature research and other experimental data that signify an occurrence of CIWH, b) experiments in an effort to show an occurrence of CIWH and the ability to prevent CIWH, c) qualitative and quantitative results to underline the mechanism of CIWH, d) experiments that show CIWH can be prevented under certain conditions, and e) guidelines for the safe operating conditions. Based on initial experiment results it was observed that Bernoulli's effect can play an important role in wave formation and instability. A separate effect table top experiment was constructed with plexi-glass. A series of entrance effect tests and stratified experiments were carried out with different fluids to study wave formation and wave bridging. Special test series experiments were carried out to investigate the presence of a saturated layer. The effect of subcooled water and steam flow on wedge length and depth were recorded. These experiments helped create a model which calculates wedge and depth of wedge for a given condition of steam and subcooled water. A very good comparison between the experiment results and the model was obtained. These experiments also showed that the presence of saturated layer can mitigate

  18. Optimal experience in online shopping: the influence of flow

    OpenAIRE

    Sharkey, Ultan; Acton, Thomas; Conboy, Kieran

    2012-01-01

    peer-reviewed This research investigates the influences of product presentation modes, decision behaviour and the consumer experience on Internet shopping. The growth of online shopping brings with it cognitive challenges for consumers attempting to assess large numbers of options in purchase decisions. Further, there is little guidance for vendors in terms of presenting large numbers of product. In this study, online shopping is viewed as an information processing, decision ta...

  19. PREFACE: 4th Workshop on Theory, Modelling and Computational Methods for Semiconductors (TMCSIV)

    Science.gov (United States)

    Tomić, Stanko; Probert, Matt; Migliorato, Max; Pal, Joydeep

    2014-06-01

    These conference proceedings contain the written papers of the contributions presented at the 4th International Conference on Theory, Modelling and Computational Methods for Semiconductor materials and nanostructures. The conference was held at the MediaCityUK, University of Salford, Manchester, UK on 22-24 January 2014. The previous conferences in this series took place in 2012 at the University of Leeds, in 2010 at St William's College, York and in 2008 at the University of Manchester, UK. The development of high-performance computer architectures is finally allowing the routine use of accurate methods for calculating the structural, thermodynamic, vibrational, optical and electronic properties of semiconductors and their hetero- and nano-structures. The scope of this conference embraces modelling, theory and the use of sophisticated computational tools in semiconductor science and technology, where there is substantial potential for time-saving in R&D. Theoretical approaches represented in this meeting included: Density Functional Theory, Semi-empirical Electronic Structure Methods, Multi-scale Approaches, Modelling of PV devices, Electron Transport, and Graphene. Topics included, but were not limited to: Optical Properties of Quantum Nanostructures including Colloids and Nanotubes, Plasmonics, Magnetic Semiconductors, Photonic Structures, and Electronic Devices. This workshop ran for three days, with the objective of bringing together UK and international leading experts in the theoretical modelling of Group IV, III-V and II-VI semiconductors, as well as students, postdocs and early-career researchers. The first day focused on providing an introduction and overview of this vast field, aimed particularly at students, with several lectures given by recognized experts in various theoretical approaches. The following two days showcased some of the best theoretical research carried out in the UK in this field, with several contributions also from representatives of

  20. PREFACE: The 4th Symposium on the Mechanics of Slender Structures (MoSS2013)

    Science.gov (United States)

    Cao, Dengqing; Kaczmarczyk, Stefan

    2013-07-01

    This volume of Journal of Physics: Conference Series contains papers presented at the 4th Symposium on the Mechanics of Slender Structures (MoSS2013) run under the auspices of the Institute of Physics Applied Mechanics Group and hosted by Harbin Institute of Technology (China) from 7-9 January 2013. The conference has been organized in collaboration with the Technical Committee on Vibration and Sound of the American Society of Mechanical Engineers and follows a one day seminar on Ropes, Cables, Belts and Chains: Theory and Applications and the MoSS2006 symposium held at the University of Northampton (UK) in 2004 and 2006, respectively, the MoSS2008 symposium held at the University of Maryland Baltimore County (USA) in 2008 and the MoSS2010 symposium hosted by Mondragon University and held in San Sebastian (Spain) in 2010. The remit of the Symposium on the Mechanics of Slender Structures series involves a broad range of scientific areas. Applications of slender structures include terrestrial, marine and space systems. Moving elastic elements such as ropes, cables, belts and tethers are pivotal components of many engineering systems. Their lengths often vary when the system is in operation. The applications include vertical transportation installations and, more recently, space tether propulsion systems. Traction drive elevator installations employ ropes and belts of variable length as a means of suspension, and also for the compensation of tensile forces over the traction sheave. In cranes and mine hoists, cables and ropes are subject to length variation in order to carry payloads. Tethers experiencing extension and retraction are important components of offshore and marine installations, as well as being proposed for a variety of different space vehicle propulsion systems based on different applications of momentum exchange and electrodynamic interactions with planetary magnetic fields. Furthermore, cables and slender rods are used extensively in civil engineering

  1. Skills-demands compatibility as a determinant of flow experience in an inductive reasoning task.

    Science.gov (United States)

    Schiefele, Ulrich; Raabe, Andreas

    2011-10-01

    The skills-demands fit hypothesis of flow theory was examined. Based on the earlier finding that high demands in a game situation do not reduce the experience of flow, a cognitive task paradigm was used. The effect of skills-demands compatibility on the experience of flow but not of other, similar psychological states (i.e., concentration, negative and positive activation) was also investigated. Participants were 89 undergraduate students who worked on a number of inductive reasoning tasks in four successive trials with or without skills-demands compatibility. The results clearly supported the skills-demands fit hypothesis; concentration and activation were affected only by the tasks' difficulty. Inductive reasoning tasks are a useful tool for the experimental analysis of flow, and skills-demands compatibility is a significant and powerful condition of flow, but not of other, similar psychological states.

  2. Prediction of the surface roughness of AA6082 flow-formed tubes by design of experiments

    International Nuclear Information System (INIS)

    Srinivasulu, M.; Komaraiah, M.; Rao, C. S. Krishna Prasada

    2013-01-01

    Flow forming is a modern, chipless metal forming process that is employed for the production of thin-walled seamless tubes. Experiments are conducted on AA6082 alloy pre-forms to flow form into thin-walled tubes on a CNC flow-forming machine with a single roller. Design of experiments is used to predict the surface roughness of flow-formed tubes. The process parameters selected for this study are the roller axial feed, mandrel speed, and roller radius. A standard response surface methodology (RSM) called the Box Behnken design is used to perform the experimental runs. The regression model developed by RSM successfully predicts the surface roughness of AA6082 flow-formed tubes within the range of the selected process parameters.

  3. Prediction of the surface roughness of AA6082 flow-formed tubes by design of experiments

    Energy Technology Data Exchange (ETDEWEB)

    Srinivasulu, M. [Government Polytechnic for Women Badangpet, Hyderabad (India); Komaraiah, M. [Sreenidhi Institute of Science and Technology, Hyderabad (India); Rao, C. S. Krishna Prasada [Bharat Dynamics Limited, Hyderabad (India)

    2013-06-15

    Flow forming is a modern, chipless metal forming process that is employed for the production of thin-walled seamless tubes. Experiments are conducted on AA6082 alloy pre-forms to flow form into thin-walled tubes on a CNC flow-forming machine with a single roller. Design of experiments is used to predict the surface roughness of flow-formed tubes. The process parameters selected for this study are the roller axial feed, mandrel speed, and roller radius. A standard response surface methodology (RSM) called the Box Behnken design is used to perform the experimental runs. The regression model developed by RSM successfully predicts the surface roughness of AA6082 flow-formed tubes within the range of the selected process parameters.

  4. The fluid mechanics of channel fracturing flows: experiment

    Science.gov (United States)

    Rashedi, Ahmadreza; Tucker, Zachery; Ovarlez, Guillaume; Hormozi, Sarah

    2017-11-01

    We show our preliminary experimental results on the role of fluid mechanics in channel fracturing flows, particularly yield stress fracturing fluids. Recent trends in the oil industry have included the use of cyclic pumping of a proppant slurry interspersed with a yield stress fracturing fluid, which is found to increase wells productivity, if particles disperse in a certain fashion. Our experimental study aims to investigate the physical mechanisms responsible for dispersing the particles (proppant) within a yield stress carrier fluid, and to measure the dispersion of proppant slugs in various fracturing regimes. To this end we have designed and built a unique experimental setup that resembles a fracture configuration coupled with a particle image/tracking velocimetry setup operating at micro to macro dimensions. Moreover, we have designed optically engineered suspensions of complex fluids with tunable yield stress and consistency, well controlled density match-mismatch properties and refractive indices for both X-rays and visible lights. We present our experimental system and preliminary results. NSF (Grant No. CBET-1554044- CAREER), ACS PRF (Grant No. 55661-DNI9).

  5. Further development of drag bodies for the measurement of mass flow rates during blowdown experiments

    International Nuclear Information System (INIS)

    Brockmann, E.; John, H.; Reimann, J.

    1983-01-01

    Drag bodies have already been used for sometime for the measurement of mass flow rates in blowdown experiments. Former research concerning the drag body behaviour in non-homogeneous two-phase flows frequently dealt with special effects by means of theoretical models only. For pipe flows most investigations were conducted for ratios of drag plate area to pipe cross section smaller 0.02. The present paper gives the results of experiments with drag bodies in a horizontal, non-homogeneous two-phase pipe flow with slip, which were carried through under the sponsorship of the German Ministry for Research and Technology (BMFT). Special interest was layed on the behaviour of the drag coefficient in stationary flows and at various cross sectional ratios. Both design and response of various drag bodies, which were developed at the Battelle-Institut, were tested in stationary and instationary two-phase flows. The influences of density and velocity profiles as well as the drag body position were studied. The results demonstrate, that the drag body is capable of measuring mass flow rates in connection with a gamma densitometer also in non-homogeneous two-phase flows. Satisfying results could be obtained, using simply the drag coefficient which was determined from single-phase flow calibrations

  6. Flow experiences in everyday classes of Spanish college students: the fit between challenge and skill

    Directory of Open Access Journals (Sweden)

    Jordi Escartin

    2014-07-01

    Full Text Available This study is concerned with the flow state as a high intrinsic motivation experience. Following Csikszenmihalyi´s theoretical model (1990, we analyze in which contents within the social psychology subject, students experience more flow. Participants were Spanish college students from a general course on Social Psychology. They completed a diary study during 12 master classes through the academic semester. The results showed that students experienced different states of consciousness in different sessions: relaxation, apathy, flow and anxiety, respectively. These findings provide new insight into the relationship between an academic subject and students, facilitating the creation of new and innovative strategies for learning. The ultimate goal is to modify and improve the dynamics and learning activities for the teaching course, increasing the experience of flow in class (and reducing the levels of anxiety, apathy or relaxation.

  7. CFD for subcooled flow boiling: Simulation of DEBORA experiments

    International Nuclear Information System (INIS)

    Krepper, Eckhard; Rzehak, Roland

    2011-01-01

    Highlights: → In the DEBORA subcooled boiling tests using R12 are investigated. → Radial profiles of void fraction, liquid velocity, temperature and bubble sizes at the end of the heated length were measured. → The theoretical and experimental basis of correlations used in the wall boiling model are reviewed. → An assessment of the necessary recalibrations to describe the DEBORA tests is given. → With increased generated vapour the gas fraction profile changes from wall to core peaking, not captured by the present modelling. - Abstract: In this work we investigate the present capabilities of CFD for wall boiling. The computational model used combines the Euler/Euler two-phase flow description with heat flux partitioning. Very similar modelling was previously applied to boiling water under high pressure conditions relevant to nuclear power systems. Similar conditions in terms of the relevant non-dimensional numbers have been realized in the DEBORA tests using dichlorodifluoromethane (R12) as the working fluid. This facilitated measurements of radial profiles for gas volume fraction, gas velocity, liquid temperature and bubble size. After reviewing the theoretical and experimental basis of correlations used in the model, give a careful assessment of the necessary recalibrations to describe the DEBORA tests. It is then shown that within a certain range of conditions different tests can be simulated with a single set of model parameters. As the subcooling is decreased and the amount of generated vapour increases the gas fraction profile changes from wall to core peaking. This is a major effect not captured by the present modelling. Some quantitative deviations are assessed as well and directions for further model improvement are outlined.

  8. Coronal MR imaging of the normal 3rd, 4th, and 5th lumbar and 1st sacral nerve roots

    International Nuclear Information System (INIS)

    Hald, J.K.; Nakstad, P.H.; Hauglum, B.E.

    1991-01-01

    Seven healthy volunteers underwent coronal MR imaging at 1.5 tesla of the normal 3rd, 4th, and 5th lumbar, and 1st sacral nerve roots. Coronal slices, 3-mm-thick with a 0.3-mm gap between the slices were obtained (TR/TE 600/22) through the lumbar spinal canal. All the nerve roots were visible on at least one image. One can routinely expect to demonstrate the 3rd, 4th, and 5th lumbar, and 1st sacral nerve roots on T1-weighted, 3-mm-thick coronal MR scans. We found no correlation between the degree of lumbar lordosis and the lengths of the visible nerve roots. Five patients with one of the following spinal problems: anomaly, tumor, disk herniation, and failed back surgery syndrome were examined according to our protocol. In all these cases coronal MR imaging gave the correct diagnosis. (orig.)

  9. Coronal MR imaging of the normal 3rd, 4th, and 5th lumbar and 1st sacral nerve roots

    Energy Technology Data Exchange (ETDEWEB)

    Hald, J K; Nakstad, P H; Hauglum, B E [National Hospital, Oslo (Norway). Dept. of Radiology

    1991-05-01

    Seven healthy volunteers underwent coronal MR imaging at 1.5 tesla of the normal 3rd, 4th, and 5th lumbar, and 1st sacral nerve roots. Coronal slices, 3-mm-thick with a 0.3-mm gap between the slices were obtained (TR/TE 600/22) through the lumbar spinal canal. All the nerve roots were visible on at least one image. One can routinely expect to demonstrate the 3rd, 4th, and 5th lumbar, and 1st sacral nerve roots on T1-weighted, 3-mm-thick coronal MR scans. We found no correlation between the degree of lumbar lordosis and the lengths of the visible nerve roots. Five patients with one of the following spinal problems: anomaly, tumor, disk herniation, and failed back surgery syndrome were examined according to our protocol. In all these cases coronal MR imaging gave the correct diagnosis. (orig.).

  10. The Informative Dimension of the Annex to the Annual Financial Statements in the Context of the 4th European Directive

    Directory of Open Access Journals (Sweden)

    Ovidia Doinea

    2009-10-01

    Full Text Available The fundamental disposition of the CEE 4th Directive is represented by the art.2, in which is stipulated the structuring of the annualaccounts in three documents that forms a unitary whole as following: the balance sheet, the profit and loss account and the annex. The annex is aconstitutive part of the annual accounts, being a conceptual product mentioned in the art.2 of the CEE 4th Directive. This synthetic accounting hasthe role to explain or to complete the elements offered by the balance sheet and the profit and loss account. The annex represents a valuableinstrument of informing and analysis for all the users of accounting information. The informative dimension of the annex is not limited, but theinformation presentation must respect the principle of true and fair view and that of the significant importance.

  11. Dorsally exophytic glioblastoma arising from the medulla oblongata in an adult presenting as 4th ventricular mass

    Science.gov (United States)

    Das, Kuntal Kanti; Bettaswamy, Guru Prasad; Mehrotra, Anant; Jaiswal, Sushila; Jaiswal, Awadhesh Kumar; Behari, Sanjay

    2017-01-01

    Brainstem gliomas are relatively rare in adults (medulla oblongata in a 55-year-old lady who presented with a 4th ventricular mass, and present a brief review of the literature. Till now, six cases of glioblastoma arising from the medulla oblongata have been reported. So, ours is the seventh such report. To the best of our knowledge, it also happens to be the sixth reported case of dorsally exophytic brainstem glioblastoma till date. PMID:28484537

  12. R&W Club Frederick Hosts 4th Annual Golf Tournament Benefiting The Children’s Inn at NIH | Poster

    Science.gov (United States)

    The R&W Club Frederick’s 4th Annual Golf Tournament to benefit the Children’s Inn at NIH teed off on time despite cloudy weather and scattered showers. Employees from NCI at Frederick, the main NIH campus, and Leidos Biomed, along with family and friends, came to enjoy an afternoon at the beautiful Maryland National Golf Club in Middletown and to support a wonderful charity.

  13. Novelly formed products of the interaction of fuel with construction materials of the 4th unit of Chernobyl NPP

    International Nuclear Information System (INIS)

    Borovoj, A.A.; Galkin, B.Ya.; Drapchinskij, L.V.; Krinitsyn, A.P.; Pazukhin, Eh.M.; Petrov, B.F.; Pleskachevskij, L.A.; Checherov, K.P.

    1991-01-01

    Radiation environment and position of fuel-containing masses in the bubbler pond of the 4th unit of the Chernobyl NPP are described. Classification of the products of fuel interaction with structural materials is given. Amounts of fuel on the 1st and 2nd floor of the bubbler pond are estimated. Postaccident pictures of the premises of the bubbler pond are presented for the first time

  14. Abstracts for the 4th Annual Congress on Medicine & Science in Ultra-Endurance Sports, May 30, 2017, Denver, Colorado.

    Science.gov (United States)

    2017-04-01

    The 4th Annual Congress on Medicine & Science in Ultra-Endurance Sports will be held on May 30, 2017, in Denver, Colorado. While prior meetings have been multiple-day events, the 2017 Congress will be an intense 1-day preconference to the American College of Sports Medicine annual meeting. Details of this Congress, as well as past and future meetings, can be found at the Ultra Sports Science Foundation Web site: http://ultrasportsscience.us.

  15. Flow Experience as a Quality Measure in Evaluating Physically Activating Collaborative Serious Games

    Directory of Open Access Journals (Sweden)

    Kristian J. M. Kiili

    2014-09-01

    Full Text Available The measurement of the subjective playing experience is important part of the game development process. The enjoyment level that a serious game offers is a key factor in determining whether a player will be engaged in the gameplay and achieve the objectives of the game. In this paper we report the results of a game design process in which two prototypes of a collaborative exergame were studied. The main aim of the paper is to explore to what extend the measurement of flow experience can facilitate the game evaluation and design process. Alltogether 102 junior high school students participated in two user experience studies and played collaborative exergames designed to teach soft skills. Playing experience was measured with a flow questionnaire, playing behavior was observed and some of the players were interviewed. The results showed that flow experience can be used to evaluate the overall quality of the gameplay and it provides a structured approach to consider the quality of the game. However, flow does not provide detailed information about the shortages of the game and thus complementary methods is needed to identify the causes. The results also indicated that flow experience was independent of gender that supports its use in quality measurement.

  16. Experiments of steady state head and torque of centrifugal pumps in two-phase flow

    International Nuclear Information System (INIS)

    Minato, Akihiko; Tominaga, Kenji.

    1988-01-01

    Circulation pump behavior has large effect on coolant discharge flow rate in case of reactor pipe break. Experiment of two-phase pump performance was conducted as a joint study of Japanese BWR user utilities and makers. Two-phase head and torque of three centrifugal pumps in high temperature and high pressure (around 6 MPa) steam/water were measured. Head was decreased from single-phase characteristics when gas was mixed in liquid flow in condition with normal flow and normal rotation directions. When flow rate was large enough, two-phase head was about the same as single-phase one in reversal flow conditions. Two-phase head was smoothly increased as flowing steam volumetic concentration increased when flow rate was small and flow direction was reversal. Changes of torque with gas concentration were correspondent to those of head. This suggested that changes of interaction between flow and impellers due to phase slip effected on torque which caused head differences between single- and two-phase flows. Dependence of dimensionless head and torque of three test pumps on steam concentration were almost the same as each other. (author)

  17. Generation of parasitic axial flow by drift wave turbulence with broken symmetry: Theory and experiment

    Science.gov (United States)

    Hong, R.; Li, J. C.; Hajjar, R.; Chakraborty Thakur, S.; Diamond, P. H.; Tynan, G. R.

    2018-05-01

    Detailed measurements of intrinsic axial flow generation parallel to the magnetic field in the controlled shear decorrelation experiment linear plasma device with no axial momentum input are presented and compared to theory. The results show a causal link from the density gradient to drift-wave turbulence with broken spectral symmetry and development of the axial mean parallel flow. As the density gradient steepens, the axial and azimuthal Reynolds stresses increase and radially sheared azimuthal and axial mean flows develop. A turbulent axial momentum balance analysis shows that the axial Reynolds stress drives the radially sheared axial mean flow. The turbulent drive (Reynolds power) for the azimuthal flow is an order of magnitude greater than that for axial flow, suggesting that the turbulence fluctuation levels are set by azimuthal flow shear regulation. The direct energy exchange between axial and azimuthal mean flows is shown to be insignificant. Therefore, the axial flow is parasitic to the turbulence-zonal flow system and is driven primarily by the axial turbulent stress generated by that system. The non-diffusive, residual part of the axial Reynolds stress is found to be proportional to the density gradient and is formed due to dynamical asymmetry in the drift-wave turbulence.

  18. Procrastination, Flow, and Academic Performance in Real Time Using the Experience Sampling Method.

    Science.gov (United States)

    Sumaya, Isabel C; Darling, Emily

    2018-01-01

    The authors' aim was to first provide an alternative methodology in the assessment of procrastination and flow that would not reply on retrospective or prospective self-reports. Using real-time assessment of both procrastination and flow, the authors investigated how these factors impact academic performance by using the Experience Sampling Method. They assessed flow by measuring student self-reported skill versus challenge, and procrastination by measuring the days to completion of an assignment. Procrastination and flow were measured for six days before a writing assignment due date while students (n = 14) were enrolled in a research methods course. Regardless of status of flow, both the nonflow and flow groups showed high levels of procrastination. Students who experienced flow as they worked on their paper, in real time, earned significantly higher grades (M = 3.05 ± 0.30: an average grade of B) as compared with the nonflow group (M = 1.16 ± 0.33: an average grade of D; p = .007). Additionally, students experiencing flow were more accurate in predicting their grade (difference scores, flow M = 0.12 ± 0.33 vs. nonflow M = 1.39 ± 0.29; p = .015). Students in the nonflow group were nearly a grade and a half off in their prediction of their grade on the paper. To the authors' knowledge, the study is the first to provide experimental evidence showing differences in academic performance between students experiencing flow and nonflow students.

  19. An ecological study of food desert prevalence and 4th grade academic achievement in New York State school districts

    Directory of Open Access Journals (Sweden)

    Seth E. Frndak

    2014-12-01

    Full Text Available Background. This ecological study examines the relationship between food desert prevalence and academic achievement at the school district level. Design and methods. Sample included 232 suburban and urban school districts in New York State. Multiple open-source databases were merged to obtain: 4th grade science, English and math scores, school district demographic composition (NYS Report Card, regional socioeconomic indicators (American Community Survey, school district quality (US Common Core of Data, and food desert data (USDA Food Desert Atlas. Multiple regression models assessed the percentage of variation in achievement scores explained by food desert variables, after controlling for additional predictors.Results. The proportion of individuals living in food deserts significantly explained 4th grade achievement scores, after accounting for additional predictors. School districts with higher proportions of individuals living in food desert regions demonstrated lower 4th grade achievement across science, English and math. Conclusions. Food deserts appear to be related to academic achievement at the school district level among urban and suburban regions. Further research is needed to better understand how food access is associated with academic achievement at the individual level.

  20. Feasibility analysis of large length-scale thermocapillary flow experiment for the International Space Station

    Science.gov (United States)

    Alberts, Samantha J.

    The investigation of microgravity fluid dynamics emerged out of necessity with the advent of space exploration. In particular, capillary research took a leap forward in the 1960s with regards to liquid settling and interfacial dynamics. Due to inherent temperature variations in large spacecraft liquid systems, such as fuel tanks, forces develop on gas-liquid interfaces which induce thermocapillary flows. To date, thermocapillary flows have been studied in small, idealized research geometries usually under terrestrial conditions. The 1 to 3m lengths in current and future large tanks and hardware are designed based on hardware rather than research, which leaves spaceflight systems designers without the technological tools to effectively create safe and efficient designs. This thesis focused on the design and feasibility of a large length-scale thermocapillary flow experiment, which utilizes temperature variations to drive a flow. The design of a helical channel geometry ranging from 1 to 2.5m in length permits a large length-scale thermocapillary flow experiment to fit in a seemingly small International Space Station (ISS) facility such as the Fluids Integrated Rack (FIR). An initial investigation determined the proposed experiment produced measurable data while adhering to the FIR facility limitations. The computational portion of this thesis focused on the investigation of functional geometries of fuel tanks and depots using Surface Evolver. This work outlines the design of a large length-scale thermocapillary flow experiment for the ISS FIR. The results from this work improve the understanding thermocapillary flows and thus improve technological tools for predicting heat and mass transfer in large length-scale thermocapillary flows. Without the tools to understand the thermocapillary flows in these systems, engineers are forced to design larger, heavier vehicles to assure safety and mission success.

  1. Morphodynamics and sedimentary structures of bedforms under supercritical-flow conditions: new insights from flume experiments

    Science.gov (United States)

    Cartigny, Matthieu; Ventra, Dario; Postma, George; Van den Berg, Jan H.

    2014-05-01

    Supercritical-flow phenomena are fairly common in modern sedimentary environments, yet their recognition remains subordinate in the rock record. This is commonly ascribed to the poor preservation potential of deposits from supercritical flows. However, the number of documented flume datasets on supercritical-flow dynamics and sedimentary structures is very limited in comparison with available data from subcritical-flow experiments, and our inability to identify and interpret such deposits might also be due to insufficient knowledge. This article describes the results of systematic experiments spanning the full range of supercritical-flow bedforms (antidunes, chutes-and-pools, cyclic steps) developed over mobile sand beds of variable grain sizes. Flow character and related bedform patterns are constrained through time-series measurements of the bed configuration, flow depth, flow velocity and Froude number. The results allow the refinement and extension of current bedform stability diagrams in the supercritical-flow domain. The experimental dataset and the stability diagram clarify morphodynamic relationships between antidune and cyclic steps. The onset of antidunes is controlled by the flow passing a threshold value of the Froude parameter. The transition from antidunes to cyclic steps instead is completed at a threshold value of the mobility parameter, and this transition spans a wider range of values for the mobility parameter as grain size increases. Sedimentary structures associated with the development of supercritical bedforms under variable aggradation rates are revealed by means of a synthetic aggradation technique and compared with examples from field and flume studies. Aggradation rate bears an important influence on the geometry of supercritical structures, and it should be held in consideration for the identification and mutual distinction of supercritical-flow bedforms in the stratigraphic record.

  2. Something going on in Milan: a review of the 4th International PhD Student Cancer Conference.

    Science.gov (United States)

    Segré, C

    2010-01-01

    The 4th International PhD Student Cancer Conference was held at the IFOM-IEO-Campus in Milan from 19-21 May 2010 http://www.semm.it/events_researchPast.phpThe Conference covered many topics related to cancer, from basic biology to clinical aspects of the disease. All attendees presented their research, by either giving a talk or presenting a poster. This conference is an opportunity to introduce PhD students to top cancer research institutes across Europe.THE CORE PARTICIPANTING INSTITUTES INCLUDED: European School of Molecular Medicine (SEMM)-IFOM-IEO Campus, MilanBeatson Institute for Cancer Research (BICR), GlasgowCambridge Research Institute (CRI), Cambridge, UKMRC Gray Institute of Radiation Biology (GIROB), OxfordLondon Research Institute (LRI), LondonPaterson Institute for Cancer Research (PICR), ManchesterThe Netherlands Cancer Institute (NKI), Amsterdam'You organizers have crushed all my prejudices towards Italians. Congratulations, I enjoyed the conference immensely!' Even if it might have sounded like rudeness for sure this was supposed to be a genuine compliment (at least, that's how we took it), also considering that it was told by a guy who himself was the fusion of two usually antithetical concepts: fashion style and English nationality.The year 2010 has marked an important event for Italian research in the international scientific panorama: the European School of Molecular Medicine (SEMM) had the honour to host the 4th International PhD Student Cancer Conference, which was held from 19-21 May 2010 at the IFOM-IEO-Campus (http://www.semm.it/events_researchPast.php) in Milan.The conference was attended by more than one hundred students, coming from a selection of cutting edge European institutes devoted to cancer research. The rationale behind it is the promotion of cooperation among young scientists across Europe to debate about science and to exchange ideas and experiences. But that is not all, it is also designed for PhD students to get in touch

  3. The relationship between self-disgust, guilt, and flow experience among Japanese undergraduates.

    Science.gov (United States)

    Hirao, Kazuki; Kobayashi, Ryuji

    2013-01-01

    To determine the relationship between self-disgust, guilt, and flow experience. A cross-sectional survey was conducted in a convenience sample of 142 Kibi International University students (mean age, 20.09 ± 1.24 years; 85 males and 57 females). Each participant was evaluated using the Flow Experience Checklist, Self-Disgust Scale, and Situational Guilt Inventory. Correlation analysis was used to describe the strength and direction of the relationship between variables. We employed Pearson's partial correlations, adjusted for age and sex, using dummy variables (female = 0, male = 1). Analysis of the relationship between the frequency of flow experience and the Self-Disgust Scale scores showed a statistically significant negative correlation, whereas the duration of the activity and the Situational Guilt Inventory score showed a significant positive correlation. The quality of flow experience and the Situational Guilt Inventory score showed a significant positive correlation. These findings suggest that flow experience could be helpful for those who need treatment to reduce negative emotions.

  4. The relationship between self-disgust, guilt, and flow experience among Japanese undergraduates

    Directory of Open Access Journals (Sweden)

    Hirao K

    2013-07-01

    Full Text Available Kazuki Hirao, Ryuji Kobayashi Department of Occupational Therapy, School of Health Science and Social Welfare, Kibi International University, Okayama, Japan Purpose: To determine the relationship between self-disgust, guilt, and flow experience. Methods: A cross-sectional survey was conducted in a convenience sample of 142 Kibi International University students (mean age, 20.09 ± 1.24 years; 85 males and 57 females. Each participant was evaluated using the Flow Experience Checklist, Self-Disgust Scale, and Situational Guilt Inventory. Correlation analysis was used to describe the strength and direction of the relationship between variables. We employed Pearson's partial correlations, adjusted for age and sex, using dummy variables (female = 0, male = 1. Results: Analysis of the relationship between the frequency of flow experience and the Self-Disgust Scale scores showed a statistically significant negative correlation, whereas the duration of the activity and the Situational Guilt Inventory score showed a significant positive correlation. The quality of flow experience and the Situational Guilt Inventory score showed a significant positive correlation. Conclusion: These findings suggest that flow experience could be helpful for those who need treatment to reduce negative emotions. Keywords: negative emotion, mental health, positive psychology

  5. Flow structure formation in an ion-unmagnetized plasma: The HYPER-II experiments

    Science.gov (United States)

    Terasaka, K.; Tanaka, M. Y.; Yoshimura, S.; Aramaki, M.; Sakamoto, Y.; Kawazu, F.; Furuta, K.; Takatsuka, N.; Masuda, M.; Nakano, R.

    2015-01-01

    The HYPER-II device has been constructed in Kyushu University to investigate the flow structure formation in an ion-unmagnetized plasma, which is an intermediate state of plasma and consists of unmagnetized ions and magnetized electrons. High density plasmas are produced by electron cyclotron resonance heating, and the flow field structure in an inhomogeneous magnetic field is investigated with a directional Langmuir probe method and a laser-induced fluorescence method. The experimental setup has been completed and the diagnostic systems have been installed to start the experiments. A set of coaxial electrodes will be introduced to control the azimuthal plasma rotation, and the effect of plasma rotation to generation of rectilinear flow structure will be studied. The HYPER-II experiments will clarify the overall flow structure in the inhomogeneous magnetic field and contribute to understanding characteristic feature of the intermediate state of plasma.

  6. Using particle tracking to measure flow instabilities in an undergraduate laboratory experiment

    Science.gov (United States)

    Kelley, Douglas H.; Ouellette, Nicholas T.

    2011-03-01

    Much of the drama and complexity of fluid flow occurs because its governing equations lack unique solutions. The observed behavior depends on the stability of the multitude of solutions, which can change with the experimental parameters. Instabilities cause sudden global shifts in behavior. We have developed a low-cost experiment to study a classical fluid instability. By using an electromagnetic technique, students drive Kolmogorov flow in a thin fluid layer and measure it quantitatively with a webcam. They extract positions and velocities from movies of the flow using Lagrangian particle tracking and compare their measurements to several theoretical predictions, including the effect of the drive current, the spatial structure of the flow, and the parameters at which instability occurs. The experiment can be tailored to undergraduates at any level or to graduate students by appropriate emphasis on the physical phenomena and the sophisticated mathematics that govern them.

  7. International Workshop on Detection, Classification and Localization of Marine Mammals Using Passive Acoustics (4th). International Workshop on Density Estimation of Marine Mammals Using Passive Acoustics (1st)

    Science.gov (United States)

    2009-09-13

    Università degli Studi di Pavia Dipartimento di Biologia Animale Centro Interdisciplinare di Bioacustica e Ricerche Ambientali 4th International...Dipartimento di Biologia Animale Centro Interdisciplinare di Bioacustica e Ricerche Ambientali 4th International Workshop on Detection, Classification...mail: gianni.pavan@unipv.it ORGANIZED BY: Università degli Studi di Pavia - Dipartimento di Biologia Animale CIBRA CENTRO INTERDISCIPLINARE DI

  8. The Effect of Mathematical Worksheets Based on Multiple Intelligences Theory on the Academic Achievement of the Students in the 4th Grade Primary School

    Science.gov (United States)

    Inan, Cemil; Erkus, Serdar

    2017-01-01

    The aim of this research is to examine the effect of Math worksheets based on the Multiple Intelligences Theory on the academic achievement of students in the 4th grade primary school. The sample of the research consists of 64 (32 experimental and 32 control) students who are studying in the 4th grade in a primary school affiliated to the Ministry…

  9. Analysis of clad motion observed in loss of flow accident simulation experiments

    International Nuclear Information System (INIS)

    Henkel, P.R.

    1987-01-01

    The clad motion observed in the first two STAR experiments is analysed. The movies reveal that at moderate temperatures molten cladding does not wet fresh fuel (within an argon gas atmosphere). The prevailing flow regime consists of single waves contacting the fuel pins and entrained drops. Entrainment is possible already at gas velocities of order 40-50 m/s. A multichannel clad motion model is presented that accounts for both flow modes. (author)

  10. Turbulent-flow split model and supporting experiments for wire-wrapped core assemblies

    International Nuclear Information System (INIS)

    Chiu, C.; Todreas, N.; Rohsenow, W.

    1978-04-01

    A flow split model for the turbulent flow in a wire-wrapped nuclear fuel rod assembly is developed taking the form drag and sweeping flow between subchannels into consideration. This model is applicable to the flow distribution between two types of subchannels, i.e., interior and edge subchannels. The constants in this model for each type of subchannel were determined using all experimental data in the literature and the results of two tests performed as part of this study to fill a gap in the available literature. These experiments to measure flow split were performed on two wire-wrapped 61 pin bundles of pin pitch to pin diameter ratio, P/D, equal to 1.063 and wire lead to pin diameter ratios, H/D, of 4 and 8. The predictions of this model match all experimental data in the literature within +- 5%

  11. Colloidal Asphaltene Deposition and Aggregation in Capillary Flow: Experiments and Mesoscopic Simulation

    Science.gov (United States)

    Boek, Edo S.; Ladva, Hemant K.; Crawshaw, John P.; Padding, Johan T.

    2008-07-01

    The aggregation and deposition of colloidal asphaltene in reservoir rock is a significant problem in the oil industry. To obtain a fundamental understanding of this phenomenon, we have studied the deposition and aggregation of colloidal asphaltene in capillary flow by experiment and simulation. For the simulation, we have used the stochastic rotation dynamics (SRD) method, in which the solvent hydrodynamic emerges from the collisions between the solvent particles, while the Brownian motion emerges naturally from the interactions between the colloidal asphaltene particles and the solvent. The asphaltene colloids interact through a screened Coulomb potential. We vary the well depth ɛ∝ and the flow rate v to obtain Peflow≫1 (hydrodynamic interactions dominate) and Re≪1 (Stokes flow). In the simulations, we impose a pressure drop over the capillary length and measure the corresponding solvent flow rate. We observe that the transient solvent flow rate decreases when the asphaltene particles become more "sticky". For a well depth ɛ∝ = 2kBT, a monolayer deposits on the capillary wall. With an increasing well depth, the capillary becomes totally blocked. The clogging is transient for ɛ∝ = 5kBT, but appears to be permanent for ɛ∝ = 10-20 kBT. We compare our simulation results with flow experiments in glass capillaries, where we use extracted asphaltenes in toluene, reprecipitated with n-heptane. In the experiments, the dynamics of asphaltene precipitation and deposition were monitored in a slot capillary using optical microscopy under flow conditions similar to those used in the simulation. Maintaining a constant flow rate of 5 μL min-1, we found that the pressure drop across the capillary first increased slowly, followed by a sharp increase, corresponding to a complete local blockage of the capillary. Doubling the flow rate to 10 μL min-1, we observe that the initial deposition occurs faster but the deposits are subsequently entrained by the flow. We

  12. A High Performance Pulsatile Pump for Aortic Flow Experiments in 3-Dimensional Models.

    Science.gov (United States)

    Chaudhury, Rafeed A; Atlasman, Victor; Pathangey, Girish; Pracht, Nicholas; Adrian, Ronald J; Frakes, David H

    2016-06-01

    Aortic pathologies such as coarctation, dissection, and aneurysm represent a particularly emergent class of cardiovascular diseases. Computational simulations of aortic flows are growing increasingly important as tools for gaining understanding of these pathologies, as well as for planning their surgical repair. In vitro experiments are required to validate the simulations against real world data, and the experiments require a pulsatile flow pump system that can provide physiologic flow conditions characteristic of the aorta. We designed a newly capable piston-based pulsatile flow pump system that can generate high volume flow rates (850 mL/s), replicate physiologic waveforms, and pump high viscosity fluids against large impedances. The system is also compatible with a broad range of fluid types, and is operable in magnetic resonance imaging environments. Performance of the system was validated using image processing-based analysis of piston motion as well as particle image velocimetry. The new system represents a more capable pumping solution for aortic flow experiments than other available designs, and can be manufactured at a relatively low cost.

  13. Experiments on vertical gas-liquid pipe flows using ultrafast X-ray tomography

    Energy Technology Data Exchange (ETDEWEB)

    Banowski, M.; Beyer, M.; Lucas, D.; Hoppe, D.; Barthel, F. [Helmholtz-Zentrum Dresden-Rossendorf (Germany). Inst. fuer Sicherheitsforschung

    2016-12-15

    For the qualification and validation of two-phase CFD-models for medium and large-scale industrial applications dedicated experiments providing data with high temporal and spatial resolution are required. Fluid dynamic parameter like gas volume fraction, bubble size distribution, velocity or turbulent kinetic energy should be measured locally. Considering the fact, that the used measurement techniques should not affect the flow characteristics, radiation based tomographic methods are the favourite candidate for such measurements. Here the recently developed ultrafast X-ray tomography, is applied to measure the local and temporal gas volume fraction distribution in a vertical pipe. To obtain the required frame rate a rotating X-ray source by a massless electron beam and a static detector ring are used. Experiments on a vertical pipe are well suited for development and validation of closure models for two-phase flows. While vertical pipe flows are axially symmetrically, the boundary conditions are well defined. The evolution of the flow along the pipe can be investigated as well. This report documents the experiments done for co-current upwards and downwards air-water and steam-water flows as well as for counter-current air-water flows. The details of the setup, measuring technique and data evaluation are given. The report also includes a discussion on selected results obtained and on uncertainties.

  14. Flow Boiling and Condensation Experiment (FBCE) for the International Space Station

    Science.gov (United States)

    Mudawar, Issam; O'Neill, Lucas; Hasan, Mohammad; Nahra, Henry; Hall, Nancy; Balasubramaniam, R.; Mackey, Jeffrey

    2016-01-01

    An effective means to reducing the size and weight of future space vehicles is to replace present mostly single-phase thermal management systems with two-phase counterparts. By capitalizing upon both latent and sensible heat of the coolant rather than sensible heat alone, two-phase thermal management systems can yield orders of magnitude enhancement in flow boiling and condensation heat transfer coefficients. Because the understanding of the influence of microgravity on two-phase flow and heat transfer is quite limited, there is an urgent need for a new experimental microgravity facility to enable investigators to perform long-duration flow boiling and condensation experiments in pursuit of reliable databases, correlations and models. This presentation will discuss recent progress in the development of the Flow Boiling and Condensation Experiment (FBCE) for the International Space Station (ISS) in collaboration between Purdue University and NASA Glenn Research Center. Emphasis will be placed on the design of the flow boiling module and on new flow boiling data that were measured in parabolic flight, along with extensive flow visualization of interfacial features at heat fluxes up to critical heat flux (CHF). Also discussed a theoretical model that will be shown to predict CHF with high accuracy.

  15. Erosion by sliding wear in granular flows: Experiments with realistic contact forces

    Science.gov (United States)

    Stark, C. P.; Hung, C. Y.; Smith, B.; Li, L.; Grinspun, E.; Capart, H.

    2015-12-01

    Debris flow erosion is a powerful and sometimes dominant process in steep channels. Despite its importance, this phenomenon is relatively little studied in the lab. The large drum experiments of Hsu are a notable exception, in which almost-field-scale impact forces were generated at the head of a synthetic debris flow whose properties (grain size, proportion of fines, etc) were varied widely.A key challenge in these and similar experiments is to explore how erosion rate varies as a function of the scale of the flow (thereby varying inertial stresses, impact forces, etc). The geometrical limitations of most lab experiments, and their short run time, severely limit the scope of such explorations.We achieve this scale exploration in a set of drum erosion experiments by varying effective gravity across several orders of magnitude (1g, 10g, 100g) in a geotechnical centrifuge. By half-filling our 40cm-diameter drum with dry 2.3mm grains, placing a synthetic rock plate at the back and a glass plate at the front 3cm apart, and rotating the drum at 1-50rpm, we simulate wear in a channelized dry granular flow. In contrast to Hsu's experiments, we focus on sliding wear erosion at the flow boundary rather than impact/frictional wear at the flow head. By varying effective gravity from 1g-100g we can tune the pressure exerted by the grains at the boundary without having to change the scale of our apparatus. Using a recently developed depth-averaged, kinetic-energy closure theory for granular flow, we can simultaneously tune the drum rotation rate such that the flow dynamics remain invariant. We can thereby explore how changing the scale of a granular flow, and thus the contact forces of grains on the boundary, controls the rate of rock erosion. Using a small apparatus we can simulate the erosion generated by debris flows several meters deep involving grains up to 10cm in diameter.Our results suggest that sliding wear is the main erosion process, and are consistent with Archard

  16. Controls on Lava Flow Morphology and Propagation: Using Laboratory Analogue Experiments

    Science.gov (United States)

    Peters, S.; Clarke, A. B.

    2017-12-01

    The morphology of lava flows is controlled by eruption rate, composition, cooling rate, and topography [Fink and Griffiths, 1990; Gregg and Fink, 2000, 2006]. Lava flows are used to understand how volcanoes, volcanic fields, and igneous provinces formed and evolved [Gregg and Fink., 1996; Sheth, 2006]. This is particularly important for other planets where compositional data is limited and historical context is nonexistent. Numerical modeling of lava flows remains challenging, but has been aided by laboratory analog experiments [Gregg and Keszrthelyi, 2004; Soule and Cashman, 2004]. Experiments using polyethylene glycol (PEG) 600 wax have been performed to understand lava flow emplacement [Fink and Griffiths, 1990, 1992; Gregg and Fink, 2000]. These experiments established psi (hereafter denoted by Ψ), a dimensionless parameter that relates crust formation and advection timescales of a viscous gravity current. Four primary flow morphologies corresponding to discreet Ψ ranges were observed. Gregg and Fink [2000] also investigated flows on slopes and found that steeper slopes increase the effective effusion rate producing predicted morphologies at lower Ψ values. Additional work is needed to constrain the Ψ parameter space, evaluate the predictive capability of Ψ, and determine if the preserved flow morphology can be used to indicate the initial flow conditions. We performed 514 experiments to address the following controls on lava flow morphology: slope (n = 282), unsteadiness/pulsations (n = 58), slope & unsteadiness/pulsations (n = 174), distal processes, and emplacement vs. post-emplacement morphologies. Our slope experiments reveal a similar trend to Gregg and Fink [2000] with the caveat that very high and very low local & source eruption rates can reduce the apparent predictive capability of Ψ. Predicted Ψ morphologies were often produced halfway through the eruption. Our pulse experiments are expected to produce morphologies unique to each eruption rate

  17. Particle size reduction in debris flows: Laboratory experiments compared with field data from Inyo Creek, California

    Science.gov (United States)

    Arabnia, O.; Sklar, L. S.; Mclaughlin, M. K.

    2014-12-01

    Rock particles in debris flows are reduced in size through abrasion and fracture. Wear of coarse sediments results in production of finer particles, which alter the bulk material rheology and influence flow dynamics and runout distance. Particle wear also affects the size distribution of coarse particles, transforming the initial sediment size distribution produced on hillslopes into that delivered to the fluvial channel network. A better understanding of the controls on particle wear in debris flows would aid in the inferring flow conditions from debris flow deposits, in estimating the initial size of sediments entrained in the flow, and in modeling debris flow dynamics and mapping hazards. The rate of particle size reduction with distance traveled should depend on the intensity of particle interactions with other particles and the flow boundary, and on rock resistance to wear. We seek a geomorphic transport law to predict rate of particle wear with debris flow travel distance as a function of particle size distribution, flow depth, channel slope, fluid composition and rock strength. Here we use four rotating drums to create laboratory debris flows across a range of scales. Drum diameters range from 0.2 to 4.0 m, with the largest drum able to accommodate up to 2 Mg of material, including boulders. Each drum has vanes along the boundary to prevent sliding. Initial experiments use angular clasts of durable granodiorite; later experiments will use less resistant rock types. Shear rate is varied by changing drum rotational velocity. We begin experiments with well-sorted coarse particle size distributions, which are allowed to evolve through particle wear. The fluid is initially clear water, which rapidly acquires fine-grained wear products. After each travel increment all coarse particles (mass > 0.4 g) are weighed individually. We quantify particle wear rates using statistics of size and mass distributions, and by fitting various comminution functions to the data

  18. Microgravity and bone cell mechanosensitivity: FLOW experiment during the DELTA mission

    Science.gov (United States)

    Bacabac, Rommel G.; Van Loon, Jack J. W. A.; de Blieck-Hogervorst, Jolanda M. A.; Semeins, Cor M.; Zandieh-Doulabi, Behrouz; Helder, Marco N.; Smit, Theo H.; Klein-Nulend, Jenneke

    2007-09-01

    The catabolic effects of microgravity on mineral metabolism in bone organ cultures might be explained as resulting from an exceptional form of disuse. It is possible that the mechanosensitivity of bone cells is altered under near weightlessness conditions, which likely contributes to disturbed bone metabolism observed in astronauts. In the experiment "FLOW", we tested whether the production of early signaling molecules that are involved in the mechanical load-induced osteogenic response by bone cells is changed under microgravity conditions. FLOW was one of the Biological experiment entries to the Dutch Soyuz Mission "DELTA" (Dutch Expedition for Life Science, Technology and Atmospheric Research). FLOW was flown by the Soyuz craft, launched on April 19, 2004, on its way to the International Space Station. Primary osteocytes, osteoblasts, and periosteal fibroblasts were incubated in plunger boxes, developed by Centre for Concepts in Mechatronics, using plunger activation events for single pulse fluid shear stress stimulations. Due to unforeseen hardware complications, results from in-flight cultures are considered lost. Ground control experiments showed an accumulative increase of NO in medium for osteocytes (as well as for osteoblasts and periosteal fibroblasts). Data from the online-NO sensor showed that the NO produced in medium by osteocytes increased sharply after pulse shear stress stimulations. COX-2 mRNA expression revealed high levels in osteoblasts compared to the other cell types tested. In conclusion, preparations for the FLOW experiment and preliminary ground results indicate that the FLOW setup is viable for a future flight opportunity.

  19. Evaluation of Core Bypass Flow in the Prismatic VHTR with a Multi-block Experiment

    International Nuclear Information System (INIS)

    Lee, Jeong Hun; Yoon, Su Jong; Park, Goon Cherl; Kim, Min Hwan

    2010-01-01

    The core of Prismatic Modular Reactor (PMR) consists of assemblies of hexagonal graphite fuel and reflector elements. The core bypass flow of Very High Temperature Reactor (VHTR) is defined as the core flow that does not pass through the coolant channels but passes through the bypass gap between fuel elements. The increase in bypass flow makes the decrease in effective coolant flow. Since the core bypass flow has a negative impact on safety and efficiency of VHTR, core bypass phenomena have to be investigated to improve the core thermal margin of VHTR. For this purpose, the international project, I-NERI project, has been carried out since 2008. I-NERI project is collaborative project that KAERI and SNU of Korea side and INL, ANL and TAMU of U.S side are involved. In order to evaluate the core bypass flow, the multicolumn and multi-layer experimental facility is designed by SNU. In this experiment, the effect of cross-flow and local variation of bypass gap on the bypass flow distribution is investigated. Furthermore, the experimental data will be used for validation of CFD code or thermal hydraulic analysis codes such as GAMMA or GAS-NET

  20. An Evaluation of Factors Affecting Decision Making Among 4th Grade Elementary School Students with Low Socio-Economic Status

    Directory of Open Access Journals (Sweden)

    Alper KAŞKAYA

    2017-06-01

    Full Text Available Decision making is one of the most important life skills. While making correct, timely, accurate and appropriate decisions lead to positive changes in one’s life, making incorrect decisions may have a negative impact. It is an important issue to examine what the 4th grade students in primary school have about the decision-making ability to be achieved in adolescence and what qualities 4th grade primary students should have for this skill. Evaluation of 4th grade elementary school students for developmental characteristics and qualifications they need to have to be able to gain appropriate decision making ability by puberty emerges as an important issue. Even though age 9-10 is not a period when important or life changing decisions are made, it is still considered the period that individuals start to make real decisions in their life. In this age period, we believe that attempts can be made to help children use their decision making ability more effectively by identifying factors affecting this behavior. In this regard, the aim of this study is to determine factors that have impact on children’s decision making process. This study is designed as a case study and conducted according to qualitative research approach. The study was conducted with 34 elementary school students and 3 teachers. Student interview forms developed by researchers were used to collect the data. In accordance with the data obtained, interviews were conducted with the teachers. The content analysis is included during data analysis process. In our study, we have shown that TV-media, family- close family/friends, neighborhood, the teaching process and some developmental characteristics are found to have affected children’s decision making.

  1. HEAVY ION FUSION SCIENCE VIRTUAL NATIONAL LABORATORY 4th QUARTER 2008 MILESTONE REPORT

    International Nuclear Information System (INIS)

    Bieniosek, F.M.; Anders, A.; Barnard, J.J.; Dickinson, M.R.; Greenway, W.; Henestroza, E.; Katayanagi, T.; Logan, B.G.; Lee, C.W.; Leitner, M.; Lidia, S.; More, R.M.; Ni, P.; Roy, P.K.; Seidl, P.A.; Waltron, W.

    2008-01-01

    This milestone has been met. In the previous quarter (3rd quarter FY2008), the Heavy Ion Fusion Science Virtual National Laboratory (HIFS-VNL) completed the new experimental target chamber facility for future Warm Dense Matter (WDM) experiments [1]. The target chamber is operational and target experiments are now underway, using beams focused by a final focus solenoid and compressed by an improved bunching waveform. Initial experiments have demonstrated the capability of the Neutralized Drift Compression Experiment (NDCX) beam to heat bulk matter in target foils. The experiments have focused on tuning and characterizing the NDCX beam in the target chamber, implementing the target assembly, and implementing target diagnostics in the target chamber environment. We have completed a characterization and initial optimization of the compressed and uncompressed NDCX beam entering the target chamber. The neutralizing plasma has been significantly improved to increase the beam neutralization in the target chamber. Preliminary results from recent beam tests of a gold cone for concentrating beam energy on target are encouraging and indicate the potential to double beam intensity on target. Other advantages of the cone include the large amount of neutralizing secondary electrons expected from the grazing incidence at the cone walls, and the shielding of the target from the edges of the beam pulse. The first target temperature measurements with the fast optical pyrometer were made on Sep. 12, 2008. The fast optical pyrometer is a unique and significant new diagnostic. These new results demonstrate for the first time beam heating of the target to a temperature well over 2000 K. The initial experimental results are suggestive of potentially interesting physics. The rapid initial rise and subsequent decay of the target temperature during the beam pulse indicate changes in the balance of beam heating and target evaporative cooling, a behavior which may be affected by phenomena such

  2. Optimal Experience and Personal Growth: Flow and the Consolidation of Place Identity.

    Science.gov (United States)

    Bonaiuto, Marino; Mao, Yanhui; Roberts, Scott; Psalti, Anastasia; Ariccio, Silvia; Ganucci Cancellieri, Uberta; Csikszentmihalyi, Mihaly

    2016-01-01

    This study examined the relationship between flow experience and place identity, based on eudaimonistic identity theory (EIT) which prioritizes self-defining activities as important for an individual's identification of his/her goals, values, beliefs, and interests corresponding to one's own identity development or enhancement. This study focuses on place identity, the identity's features relating to a person's relation with her/his place. The study is also based on flow theory, according to which some salient features of an activity experience are important for happiness and well-being. Questionnaire surveys on Italian and Greek residents focused on their perceived flow and place identity in relation to their own specific local place experiences. The overall findings revealed that flow experience occurring in one's own preferred place is widely reported as resulting from a range of self-defining activities, irrespective of gender or age, and it is positively and significantly associated with one's own place identity. Such findings provide the first quantitative evidence about the link between flow experienced during meaningfully located self-defining activities and identity experienced at the place level, similarly to the corresponding personal and social levels that had been previously already empirically tested. Results are also discussed in terms of their implications for EIT's understanding and enrichment, especially by its generalization from the traditional, personal identity level up to that of place identity. More generally, this study has implications for maintaining or enhancing one's own place identity, and therefore people-place relations, by means of facilitating a person's flow experience within psychologically meaningful places.

  3. Optimal Experience and Personal Growth: Flow and the Consolidation of Place Identity

    Science.gov (United States)

    Bonaiuto, Marino; Mao, Yanhui; Roberts, Scott; Psalti, Anastasia; Ariccio, Silvia; Ganucci Cancellieri, Uberta; Csikszentmihalyi, Mihaly

    2016-01-01

    This study examined the relationship between flow experience and place identity, based on eudaimonistic identity theory (EIT) which prioritizes self-defining activities as important for an individual’s identification of his/her goals, values, beliefs, and interests corresponding to one’s own identity development or enhancement. This study focuses on place identity, the identity’s features relating to a person’s relation with her/his place. The study is also based on flow theory, according to which some salient features of an activity experience are important for happiness and well-being. Questionnaire surveys on Italian and Greek residents focused on their perceived flow and place identity in relation to their own specific local place experiences. The overall findings revealed that flow experience occurring in one’s own preferred place is widely reported as resulting from a range of self-defining activities, irrespective of gender or age, and it is positively and significantly associated with one’s own place identity. Such findings provide the first quantitative evidence about the link between flow experienced during meaningfully located self-defining activities and identity experienced at the place level, similarly to the corresponding personal and social levels that had been previously already empirically tested. Results are also discussed in terms of their implications for EIT’s understanding and enrichment, especially by its generalization from the traditional, personal identity level up to that of place identity. More generally, this study has implications for maintaining or enhancing one’s own place identity, and therefore people–place relations, by means of facilitating a person’s flow experience within psychologically meaningful places. PMID:27872600

  4. 4th Quarter Transportation Report FY 2014: Radioactive Waste Shipments to and from the Nevada National Security Site (NNSS)

    International Nuclear Information System (INIS)

    Gregory, Louis

    2014-01-01

    This report satisfies the U.S. Department of Energy (DOE), National Nuclear Security Administration Nevada Field Office (NNSA/NFO) commitment to prepare a quarterly summary report of radioactive waste shipments to and from the Nevada National Security Site (NNSS) Radioactive Waste Management Complex (RWMC) at Area 5. There were no shipments sent for offsite treatment and returned to the NNSS this quarter. There was one shipment of two drums sent for offsite treatment and disposal. This report summarizes the 4th quarter of Fiscal Year (FY) 2014 low-level radioactive waste (LLW) and mixed low-level radioactive waste (MLLW) shipments. This report also includes annual summaries for FY 2014.

  5. The World Health Organization Classification of dontogenic Lesions: A Summary of the Changes of the 2017 (4th Edition

    Directory of Open Access Journals (Sweden)

    Merva SOLUK-TEKKEŞİN

    2018-01-01

    Full Text Available The 4th edition of the World Health Organization (WHO Classification of Head and Neck Tumors was published in January 2017. The edition serves to provide an updated classification scheme, and extended genetic and molecular data that are useful as diagnostic tools for the lesions of the head and neck region. This review focuses on the most current update of odontogenic cysts and tumors based on the 2017 WHO edition. The updated classification has some important differences from the 3rd edition (2005, including a new classification of odontogenic cysts, ‘reclassified’ odontogenic tumors, and some new entities.

  6. 4th Global CRO Council for Bioanalysis: coadministered drugs stability, EMA/US FDA guidelines, 483s and carryover.

    Science.gov (United States)

    Lowes, Steve; Jersey, Jim; Shoup, Ronald; Garofolo, Fabio; Needham, Shane; Couerbe, Philippe; Lansing, Tim; Bhatti, Masood; Sheldon, Curtis; Hayes, Roger; Islam, Rafiq; Lin, Zhongping; Garofolo, Wei; Moussallie, Marc; Teixeira, Leonardo de Souza; Rocha, Thais; Jardieu, Paula; Truog, James; Lin, Jenny; Lundberg, Richard; Breau, Alan; Dilger, Carmen; Bouhajib, Mohammed; Levesque, Ann; Gagnon-Carignan, Sofi; Jenkins, Rand; Nicholson, Robert; Lin, Ming Hung; Karnik, Shane; DeMaio, William; Smith, Kirk; Cojocaru, Laura; Allen, Mike; Fatmi, Saadya; Sayyarpour, Farhad; Malone, Michele; Fang, Xinping

    2012-04-01

    The Global CRO Council for Bioanalysis (GCC) was formed in September 2010. Since then, the representatives of the member companies come together periodically to openly discuss bioanalysis and the regulatory challenges unique to the outsourcing industry. The 4th GCC Closed Forum brought together experts from bioanalytical CROs to share and discuss recent issues in regulated bioanalysis, such as the impact of coadministered drugs on stability, some differences between European Medicines Agency and US FDA bioanalytical guidance documents and lessons learned following recent Untitled Letters. Recent 483s and agency findings, as well as issues on method carryover, were also part of the topics discussed.

  7. The photoabsorption of Eu, Eu{sup +} and Eu{sup 2+} in the vicinity of 4 Th thresholds

    Energy Technology Data Exchange (ETDEWEB)

    Amusia, M.Ya.; Chernysheva, L.V. E-mail: larissa.chernysheva@pop.ioffe.rssi.ru; Ivanov, V.K

    2000-08-01

    The results of calculations of the total and partial photoionisation cross-sections of neutral Europium and its ions in the photon energy range from the threshold up to 270 eV are presented. The calculations were performed within the multi-channel Spin-Polarized Random Phase Approximation with Exchange. The main attention is given to the giant autoionizing resonance associated with the 4 Th {yields} 4 f discrete transition to vacant states in the 4f{sup 7} subshell. The comparisons with experimental data obtained recently and the results of previous calculations are made.

  8. TUMULI, ROADS AND PLOTS. DECODING THE MONUMENTAL FUNERARY SPACE OF THE 4TH-3RD CENTURIES BC KALLATIS

    Directory of Open Access Journals (Sweden)

    Maria Magdalena Ștefan

    2017-03-01

    Full Text Available The study focusses on the monumental elements of the 4th-3rd centuries BC cemeteries of Kallatis: the use of large tumuli, the implementation of a systematized network of funerary plots, the extent of the burial grounds, the discovery of a series of built chamber tombs under tumuli with elements of decorated architecture, including mural paintings and exceptional presence of a statue topping a tumulus. The detection and morphological characterisation of archaeological features and the recovering of the funerary landscapes’ spatial layout were based on historiographic study, remote-sensing and geophysical investigations.

  9. Laboratory setup and results of experiments on two-dimensional multiphase flow in porous media

    International Nuclear Information System (INIS)

    McBride, J.F.; Graham, D.N.

    1990-10-01

    In the event of an accidental release into earth's subsurface of an immiscible organic liquid, such as a petroleum hydrocarbon or chlorinated organic solvent, the spatial and temporal distribution of the organic liquid is of great interest when considering efforts to prevent groundwater contamination or restore contaminated groundwater. An accurate prediction of immiscible organic liquid migration requires the incorporation of relevant physical principles in models of multiphase flow in porous media; these physical principles must be determined from physical experiments. This report presents a series of such experiments performed during the 1970s at the Swiss Federal Institute of Technology (ETH) in Zurich, Switzerland. The experiments were designed to study the transient, two-dimensional displacement of three immiscible fluids in a porous medium. This experimental study appears to be the most detailed published to date. The data obtained from these experiments are suitable for the validation and test calibration of multiphase flow codes. 73 refs., 140 figs

  10. Evidence of flow stabilization in the ZaP Z pinch experiment

    International Nuclear Information System (INIS)

    Shumlak, U.; Crawford, E.; Golingo, R.P.; Nelson, B.A.; Zyrmpas, A.; Den Hartog, D.J.; Holly, D.J.

    2001-01-01

    The stabilizing effect of an axial flow on the m = 1 kink instability in Z pinches has been studied numerically with a linearized ideal MHD model to reveal that a sheared axial flow stabilizes the kink mode when the shear exceeds a threshold. The sheared flow stabilizing effect is investigated with the flow-through Z pinch experiment, ZaP. An azimuthal array of surface mounted magnetic probes located at the midplane of the 50 cm long pinch plasma measures the fluctuation levels of the azimuthal modes m=1, 2, and 3. After pinch formation a quiescent period is found where the mode activity is reduced to a few percent of the average field. Optical images from a fast framing camera and a HeNe interferometer also indicate a stable pinch plasma during this time. Doppler shift measurements of a C-III line correspond to an axial flow velocity of 9.6x10 4 m/s internal to the pinch. During the time when the axial plasma flow is high, the plasma experiences a quiescent period which lasts approximately 800 exponential growth times predicted by linear theory for a static plasma. (author)

  11. Experiments in a flighted conveyor comparing shear rates in compressed versus free surface flows

    Science.gov (United States)

    Pohlman, Nicholas; Higgins, Hannah; Krupiarz, Kamila; O'Connor, Ryan

    2017-11-01

    Uniformity of granular flow rate is critical in industry. Experiments in a flighted conveyor system aim to fill a gap in knowledge of achieving steady mass flow rate by correlating velocity profile data with mass flow rate measurements. High speed images were collected for uniformly-shaped particles in a bottom-driven flow conveyor belt system from which the velocity profiles can be generated. The correlation of mass flow rates from the velocity profiles to the time-dependent mass measurements will determine energy dissipation rates as a function of operating conditions. The velocity profiles as a function of the size of the particles, speed of the belt, and outlet size, will be compared to shear rate relationships found in past experiments that focused on gravity-driven systems. The dimension of the linear shear and type of decaying transition to the stationary bed may appear different due to the compression versus dilation space in open flows. The application of this research can serve to validate simulations in discrete element modeling and physically demonstrate a process that can be further developed and customized for industry applications, such as feeding a biomass conversion reactor. Sponsored by NIU's Office of Student Engagement and Experiential Learning.

  12. 4th National Conference on Thermophysical Properties of Materials and Devices

    CERN Document Server

    Prasanth, S; Prasad, A S

    2008-01-01

    The natural course of digital libraries is towards the semantic web. The content of digital repositories, whether books or articles or even e-learning modules, are to be related and presented to the machine to be interpreted. As the objects in a digital library do come with metadata and a kind of categorisation, digital libraries may offer a good starting point to experiment with semantic web technology. One can easily see the convergence of digital libraries and semantic web technology. The papers included in this e-book aim to address some of the pertinent questions in the area of convergenc

  13. 4th IEEE/ACIS International Conference on Computer and Information Science

    CERN Document Server

    2016-01-01

    This edited book presents scientific results of the 14th IEEE/ACIS International Conference on Computer and Information Science (ICIS 2015) which was held on June 28 – July 1, 2015 in Las Vegas, USA. The aim of this conference was to bring together researchers and scientists, businessmen and entrepreneurs, teachers, engineers, computer users, and students to discuss the numerous fields of computer science and to share their experiences and exchange new ideas and information in a meaningful way. Research results about all aspects (theory, applications and tools) of computer and information science, and to discuss the practical challenges encountered along the way and the solutions adopted to solve them.

  14. A Kinesthetic Learning Approach to Earth Science for 3rd and 4th Grade Students on the Pajarito Plateau, Los Alamos, NM

    Science.gov (United States)

    Wershow, H. N.; Green, M.; Stocker, A.; Staires, D.

    2010-12-01

    Current efforts towards Earth Science literacy in New Mexico are guided by the New Mexico Science Benchmarks [1]. We are geoscience professionals in Los Alamos, NM who believe there is an important role for non-traditional educators utilizing innovative teaching methods. We propose to further Earth Science literacy for local 3rd and 4th grade students using a kinesthetic learning approach, with the goal of fostering an interactive relationship between the students and their geologic environment. We will be working in partnership with the Pajarito Environmental Education Center (PEEC), which teaches the natural heritage of the Pajarito Plateau to 3rd and 4th grade students from the surrounding area, as well as the Family YMCA’s Adventure Programs Director. The Pajarito Plateau provides a remarkable geologic classroom because minimal structural features complicate the stratigraphy and dramatic volcanic and erosional processes are plainly on display and easily accessible. Our methodology consists of two approaches. First, we will build an interpretive display of the local geology at PEEC that will highlight prominent rock formations and geologic processes seen on a daily basis. It will include a simplified stratigraphic section with field specimens and a map linked to each specimen’s location to encourage further exploration. Second, we will develop and implement a kinesthetic curriculum for an exploratory field class. Active engagement with geologic phenomena will take place in many forms, such as a scavenger hunt for precipitated crystals in the vesicles of basalt flows and a search for progressively smaller rhyodacite clasts scattered along an actively eroding canyon. We believe students will be more receptive to origin explanations when they possess a piece of the story. Students will be provided with field books to make drawings of geologic features. This will encourage independent assessment of phenomena and introduce the skill of scientific observation. We

  15. Design and construction of an experiment for two-phase flow in fractured porous media

    Energy Technology Data Exchange (ETDEWEB)

    Ayala, R.E.G.; Aziz, K.

    1993-08-01

    In numerical reservoir simulation naturally fractured reservoirs are commonly divided into matrix and fracture systems. The high permeability fractures are usually entirely responsible for flow between blocks and flow to the wells. The flow in these fractures is modeled using Darcy`s law and its extension to multiphase flow by means of relative permeabilities. The influence and measurement of fracture relative permeability for two-phase flow in fractured porous media have not been studied extensively, and the few works presented in the literature are contradictory. Experimental and numerical work on two-phase flow in fractured porous media has been initiated. An apparatus for monitoring this type of flow was designed and constructed. It consists of an artificially fractured core inside an epoxy core holder, detailed pressure and effluent monitoring, saturation measurements by means of a CT-scanner and a computerized data acquisition system. The complete apparatus was assembled and tested at conditions similar to the conditions expected for the two-phase flow experiments. Fine grid simulations of the experimental setup-were performed in order to establish experimental conditions and to study the effects of several key variables. These variables include fracture relative permeability and fracture capillary pressure. The numerical computations show that the flow is dominated by capillary imbibition, and that fracture relative permeabilities have only a minor influence. High oil recoveries without water production are achieved due to effective water imbibition from the fracture to the matrix. When imbibition is absent, fracture relative permeabilities affect the flow behavior at early production times.

  16. Flow-induced decentering and tube support interaction for steam generator tubes: experiment and physical interpretation

    International Nuclear Information System (INIS)

    Gay, N.; Granger, S.

    1992-11-01

    Maintaining PWR components under reliable operating conditions requires a complex design to prevent various damaging processes including flow-induced vibration and wear mechanisms. To improve the prediction of tube/support interaction and wear in PWR components, EDF has undertaken a comprehensive program oriented to both experimental and computational studies. The present paper illustrates one aspect of this program, related to the determination of contact forces between steam generator tubes and anti-vibration bars (AVBs). The dynamic, nonlinear behavior of a U-tube excited by an air cross-flow is investigated on the CLAVECIN experiment. Interesting and rather unexpected results have been obtained, by varying clearances and flow velocities. The paper is focused on four main points: (i) the originality of the experiment with a force measurement device located in flow; (ii) the importance of a refined data processing for accurately measuring contact forces; (iii) the presentation of the unexpected phenomena revealed in the CLAVECIN experiment, i.e. a flow-induced decentering of the tube which changed the initial tube/AVB clearance, and the consequences on tube/support interaction; (iv) the influence of the actual tube/support clearance in flow on wear mechanisms. The work, presented in the second part of this paper, concentrates exclusively on the physical interpretation of the flow-induced decentering phenomenon and on the theoretical analysis of its consequences on dynamic tube/support interaction. We show that the flow-induced decentering phenomenon can be generated by an unstable quasi-static coupling between the flexible tube and the confined flow, in the vicinity of the support system. This phenomenon is not specific to the CLAVECIN tests and it can be expected every time that a movable obstacle is subjected to confined flow. Moreover, in single-sided impacting conditions, the theoretical analysis confirms the linear relation, found in the CLAVECIN tests

  17. Experiments and Large-Eddy Simulations of acoustically forced bluff-body flows

    Energy Technology Data Exchange (ETDEWEB)

    Ayache, S.; Dawson, J.R.; Triantafyllidis, A. [Department of Engineering, University of Cambridge (United Kingdom); Balachandran, R. [Department of Mechanical Engineering, University College London (United Kingdom); Mastorakos, E., E-mail: em257@eng.cam.ac.u [Department of Engineering, University of Cambridge (United Kingdom)

    2010-10-15

    The isothermal air flow behind an enclosed axisymmetric bluff body, with the incoming flow being forced by a loudspeaker at a single frequency and with large amplitude, has been explored with high data-rate Laser-Doppler Anemometry measurements and Large-Eddy Simulations. The comparison between experiment and simulations allows a quantification of the accuracy of LES for turbulent flows with periodicity and the results provide insights into the structure of flows relevant to combustors undergoing self-excited oscillations. At low forcing frequencies, the whole flow pulsates with the incoming flow, although at a phase lag that depends on spatial location. At high forcing frequencies, vortices are shed from the bluff body and the recirculation zone, as a whole, pulsates less. Despite the fact that the incoming flow has an oscillation that is virtually monochromatic, the velocity spectra show peaks at various harmonics, whose relative magnitudes vary with location. A sub-harmonic peak is also observed inside the recirculation zone possibly caused by merging of the shed vortices. The phase-averaged turbulent fluctuations show large temporal and spatial variations. The LES reproduces reasonably accurately the experimental findings in terms of phase-averaged mean and r.m.s. velocities, vortex formation, and spectral peaks.

  18. Experiments and Large-Eddy Simulations of acoustically forced bluff-body flows

    International Nuclear Information System (INIS)

    Ayache, S.; Dawson, J.R.; Triantafyllidis, A.; Balachandran, R.; Mastorakos, E.

    2010-01-01

    The isothermal air flow behind an enclosed axisymmetric bluff body, with the incoming flow being forced by a loudspeaker at a single frequency and with large amplitude, has been explored with high data-rate Laser-Doppler Anemometry measurements and Large-Eddy Simulations. The comparison between experiment and simulations allows a quantification of the accuracy of LES for turbulent flows with periodicity and the results provide insights into the structure of flows relevant to combustors undergoing self-excited oscillations. At low forcing frequencies, the whole flow pulsates with the incoming flow, although at a phase lag that depends on spatial location. At high forcing frequencies, vortices are shed from the bluff body and the recirculation zone, as a whole, pulsates less. Despite the fact that the incoming flow has an oscillation that is virtually monochromatic, the velocity spectra show peaks at various harmonics, whose relative magnitudes vary with location. A sub-harmonic peak is also observed inside the recirculation zone possibly caused by merging of the shed vortices. The phase-averaged turbulent fluctuations show large temporal and spatial variations. The LES reproduces reasonably accurately the experimental findings in terms of phase-averaged mean and r.m.s. velocities, vortex formation, and spectral peaks.

  19. Flow induced vibration characteristics in 2X3 bundle critical heat flux experiment

    International Nuclear Information System (INIS)

    Kim, Dae Hun; Chang, Soon Heung

    2005-01-01

    Above a certain heat flux, the liquid can no longer permanently wet the heater surface. This situation leads to an inordinate decrease in the surface heat transfer. This heat flux is commonly referred to as the critical heat flux (CHF). The CHF in nuclear reactors is one of the important thermal hydraulic parameters limiting the available power. Flow induced vibration (FIV) is the vibration caused by a fluid flowing around a body. In the fluid flowing system, FIV occurred by structures and flow condition. Many structures in nuclear power plant system are designed to prevent from structure failure due to FIV. Recently, Hibiki and Ishii (1998) carried out an experimental investigation on the effect of flow-induced vibration (FIV) on two-phase flow structure in vertical tube and reported that the FIV drastically changed the void fraction profiles. The void fraction profiles is one of the important parameter for determining CHF. Therefore, the investigation on the effect of FIV on CHF are needed. The research on FIV characteristics detection during CHF experiment in 2X3 bundle using R-134a has been carried out in KAIST. Using the results new FIV correlation in 2-pahse turbulent flow are suggested after finding out relation between CHF and dynamic pressure fluctuation value

  20. Observable Flow Experience in a Two-Year-Old Japanese Child's Violin Playing

    Science.gov (United States)

    Akutsu, Taichi

    2018-01-01

    This study investigated the flow experience of Jiro, a 2-year-old Japanese boy, regarding his violin playing in a social context. In this study, Jiro's violin playing was videotaped at home and during musical sessions for young children and families, guided by the author as a violinist-teacher-researcher. The method adopted a single case study…

  1. Empirical study on flow experience in China tourism e-commerce market

    Directory of Open Access Journals (Sweden)

    Jianling Wang

    2015-04-01

    Full Text Available Purpose: While tourism e-commerce develops rapidly in China, these channels are truly new to both web providers and web consumers, understanding the nature of these media attaches greater importance. This study investigates the mediation effects of flow experience on the relationship between motivation and behavior intention in tourism e-commerce.Design/methodology/approach: Based on the technology acceptance model, an empirical study is designed to test this relationship.we estimated the measurement model with 13 manifest indicators and 4 latent constructs by CFA to assess the reliability and validity of the construct measures, then tested hypotheses by OLS regression and a formal three-step mediation procedure.Findings: Overall, the results reveal that trust is incorporated in motivation and play it’s role together with other motivations; telepresence and concentration are confirmed in flow experience, and both partially mediated the relationship.Research limitations/implications: This study demonstrates that to improve consumers’ usage adoption, marketers should pay much attention to not only consumers’ motivation but also the areas such as flow experience.Originality/value: This study takes flow experience as a new perspective to explore china tourism e-commerce, estimates its measurement and tests its roles between motivation and behavior intention.

  2. Power and Flow Experience in Time-Intensive Business Simulation Game

    Science.gov (United States)

    Kiili, Kristian; Lainema, Timo

    2010-01-01

    Power is an influential component of social interaction and there are reasons for thinking that it may have important effects both on decision-making and psychological and interpersonal processes. The aim of this paper was to study the relations between the feeling of power, decision-making and flow experience in a collaborative business…

  3. 4th International Conference on Trapped Charged Particles and Fundamental Physics

    CERN Document Server

    Comyn, M; Thomson, J; Gwinner, G; TCP'06; TCP 2006

    2007-01-01

    The TCP06 conference in Parksville on Vancouver Island showcased the impressive progress in the study of fundamental physics using trapped charged particles. Atom and ion trapping has revolutionized atomic physics and related fields. It has proven to be particularly useful for fundamental physics experiments, as the tight control over the particles' degrees of freedom leads to increased precision and efficient use of exotic species such as radioactive atoms or anti-matter. The topics of the meeting included fundamental interactions and symmetries, quantum electrodynamics, quantum state manipulation and quantum information, precision spectroscopy and frequency standards, storage ring physics, highly charged ions in traps, traps for radioactive isotopes, plasmas and collective behaviour, and anti-hydrogen. Highlights from related fields such as fundamental physics studies with neutral, trapped atoms were also presented. The combination of overview articles by leaders in the field and detailed reports on recent ...

  4. GENDER ASPECT OF PHYSICAL EDUCATION ON THE 4TH GRADE PRIMARY SCHOOlCHILDREN

    Directory of Open Access Journals (Sweden)

    Goran Šekeljić

    2010-09-01

    Full Text Available The research was conducted in order to determine the effects that could be produced in motor space by applying different teaching technologies. The experiment was applied on a sample of 164 girls and 132 boys aged 10 lasting one school year. In order to collect the data on the initial and the final measurement, there were used the test techniques for the estimation of mobility abilities suggested by Kurelic and the co-authors (1975. After the experimantal and appropriate statistical procedure had been done, the observed regularities based on the growth of motor skills showed that the application of teaching technologies in this space could not provide priority concernig the gender,on the contrary its more likely to say that there is priority of better pupils without concernig their gender qualification.

  5. Status and Prospects of Agri-Tourism in Selected Municipalities of the 4th District of Batangas

    Directory of Open Access Journals (Sweden)

    BIANCA VENUS L. RECIO

    2014-08-01

    Full Text Available – The study was to identify the profile of the agri-tourism sites in the selected municipalities in the 4th district of Batangas. Specifically, it determines the status and prospects of agri-tourism in the selected municipalities in the 4th district of Batangas in terms of Socio-Economic and Environmental Aspects; and have proposed an action plan to promote the agri-tourism as a destination. The researchers have conducted the study to see how the agri-tourism benefits the community in terms of their economy and environmental aspects. This study have provided more awareness to the community about the Agri-tourism in the place. In addition this research educates people to be more vigilant enough on giving importance on the Agri-tourism we have in Batangas. Results showed that the three major agri-tourism farms in the fourth district of Batangas were Vilela’s Farm, British Farm and Moca Farm. Agri-tourism in Batangas has socio-economic effects to the residents of the fourth district of Batangas. Agri-tourism has no environmental effect as assessed by the residents of Batangas.

  6. The radial flow method: constraints from laboratory experiments on the evolution of hydraulic properties of fractures during frictional sliding experiments

    Science.gov (United States)

    Kewel, M.; Renner, J.

    2017-12-01

    The variation of hydraulic properties during sliding events is of importance for source mechanics and analyses of the evolution in effective stresses. We conducted laboratory experiments on samples of Padang granite to elucidate the interrelation between shear displacement on faults and their hydraulic properties. The cylindrical samples of 30 mm diameter and 75 mm length were prepared with a ground sawcut, inclined 35° to the cylindrical axis and accessed by a central bore of 3 mm diameter. The conventional triaxial compression experiments were conducted at effective pressures of 30, 50, and 70 MPa at slip rates of 2×10-4 and 8×10-4 mm s-1. The nominally constant fluid pressure of 30 MPa was modulated by oscillations with an amplitude of up to 0.5 MPa. Permeability and specific storage capacity of the fault were determined using the oscillatory radial-flow method that rests on an analysis of amplitude ratio and phase shift between the oscillatory fluid pressure and the oscillatory fluid flow from and into the fault plane. This method allowed us to continuously monitor the hydraulic evolution during elastic loading and frictional sliding. The chosen oscillation period of 60 s guaranteed a resolution of hydraulic properties for slip increments as small as 20 μm. The determined hydraulic properties show a fairly uniform dependence on normal stress at hydrostatic conditions and initial elastic loading. The samples exhibited stable frictional sliding with modest strengthening with increasing strain. Since not all phase-shift values fell inside the theoretical range for purely radial pressure diffusion during frictional sliding, the records of equivalent hydraulic properties exhibit some gaps. In the phases with evaluable phase-shift values, permeability fluctuates by almost one order of magnitude over slip intervals of as little as 100 μm. We suppose that the observed fluctuations are related to comminution and reconfiguration of asperities on the fault planes

  7. DEVELOPING AND PROPOSING A CONCEPTUAL MODEL OF THE FLOW EXPERIENCE DURING ONLINE INFORMATION SEARCH

    Directory of Open Access Journals (Sweden)

    Lazoc Alina

    2012-07-01

    Full Text Available Information search is an essential part of the consumer`s decision making process. The online medium offers new opportunities and challenges for information search activities (in and outside the marketing context. We are interested in the way human information experiences and behaviors are affected by this. Very often online games and social web activities are perceived as challenging, engaging and enjoyable, while online information search is far below this evaluation. Our research proposal implies that using the online medium for information search may provoke enjoyable experiences through the flow state, which may in turn positively influence an individual`s exploratory information behavior and encourage his/her pro-active market behavior. The present study sets out to improve the understanding of the online medium`s impact on human`s exploratory behavior. We hypothesize that the inclusion of the online flow experience in our research model will better explain exploratory information search behaviors. A 11-component conceptual framework is proposed to explain the manifestations of flow, its personal and technological determinants and its behavioral consequence in the context of online information search. Our research has the primary purpose to present an integrated online flow model. Its secondary objective is to stimulate extended research in the area of informational behaviors in the digital age. The paper is organized in three sections. In the first section we briefly report the analysis results of the most relevant online flow theory literature and, drawing on it, we are trying to identify variables and relationships among these. In the second part we propose a research model and use prior flow models to specify a range of testable hypothesis. Drawing on the conceptual model developed, the last section of our study presents the final conclusions and proposes further steps in evaluating the model`s validity. Future research directions

  8. ELABORATING A MEASUREMENT INSTRUMENT FOR THE FLOW EXPERIENCE DURING ONLINE INFORMATION SEARCH

    Directory of Open Access Journals (Sweden)

    Caraivan Luiza

    2012-12-01

    Full Text Available Flow is a construct imported in marketing research from social sciences in order to examine consumer behavior in the online medium. The construct describes a state of deep involvement in a challenging activity, most frequently characterized by high levels of enjoyment, control and concentration. Researchers found that the degree to which online experience is challenging can be defined, measured, and related well to important marketing variables. As shown by our extensive literature review, flow measurements include antecedents, dimensions and consequences of flow. The present paper represents a detailed description of the construct`s operationalization in the context of online information search. In this respect, our main goal is to produce a basic instrument to evaluate the flow experience of online search, in order to capitalize on the premises of an interactive, complex informational medium – the World Wide Web – and on the consequence of an exploratory informational behavior of users. The instrument is conceived to offer a primal possibility to collect data. The composition, source and significance of the 11 scales used to measure the multiple factors of the flow experience during online search are detailed in this study with the aim to ensure the compliance with scientific rigors and to facilitate correct reports of data related to the reliability and validity of measurements. For further research, we propose factor analysis to test the resulted instrument and to ensure that the measures employed are psychometrically sound. Factor analysis refers to a wide range of statistic techniques used to represent a set of variables in concordance with a reduced number of hypothetical variables called factors. Factorial analysis is used to solve two types of problems: reducing the number of variables to increase data processing speed and identifying hidden patterns in the existent data relations. However, we expect our scales to perform

  9. Design of a high-lift experiment in water including active flow control

    International Nuclear Information System (INIS)

    Beutel, T; Schwerter, M; Büttgenbach, S; Leester-Schädel, M; Sattler, S; El Sayed, Y; Radespiel, R; Zander, M; Sinapius, M; Wierach, P

    2014-01-01

    This paper describes the structural design of an active flow-control experiment. The aim of the experiment is to investigate the increase in efficiency of an internally blown Coanda flap using unsteady blowing. The system uses tailor-made microelectromechanical (MEMS) pressure sensors to determine the state of the oncoming flow and an actuated lip to regulate the mass flow and velocity of a stream near a wall over the internally blown flap. Sensors and actuators are integrated into a highly loaded system that is extremely compact. The sensors are connected to a bus system that feeds the data into a real-time control system. The piezoelectric actuators using the d 33 effect at a comparable low voltage of 120 V are integrated into a lip that controls the blowout slot height. The system is designed for closed-loop control that efficiently avoids flow separation on the Coanda flap. The setup is designed for water-tunnel experiments in order to reduce the free-stream velocity and the system’s control frequency by a factor of 10 compared with that in air. This paper outlines the function and verification of the system’s main components and their development. (technical note)

  10. The Capillary Flow Experiments Aboard the International Space Station: Increments 9-15

    Science.gov (United States)

    Jenson, Ryan M.; Weislogel, Mark M.; Tavan, Noel T.; Chen, Yongkang; Semerjian, Ben; Bunnell, Charles T.; Collicott, Steven H.; Klatte, Jorg; dreyer, Michael E.

    2009-01-01

    This report provides a summary of the experimental, analytical, and numerical results of the Capillary Flow Experiment (CFE) performed aboard the International Space Station (ISS). The experiments were conducted in space beginning with Increment 9 through Increment 16, beginning August 2004 and ending December 2007. Both primary and extra science experiments were conducted during 19 operations performed by 7 astronauts including: M. Fincke, W. McArthur, J. Williams, S. Williams, M. Lopez-Alegria, C. Anderson, and P. Whitson. CFE consists of 6 approximately 1 to 2 kg handheld experiment units designed to investigate a selection of capillary phenomena of fundamental and applied importance, such as large length scale contact line dynamics (CFE-Contact Line), critical wetting in discontinuous structures (CFE-Vane Gap), and capillary flows and passive phase separations in complex containers (CFE-Interior Corner Flow). Highly quantitative video from the simply performed flight experiments provide data helpful in benchmarking numerical methods, confirming theoretical models, and guiding new model development. In an extensive executive summary, a brief history of the experiment is reviewed before introducing the science investigated. A selection of experimental results and comparisons with both analytic and numerical predictions is given. The subsequent chapters provide additional details of the experimental and analytical methods developed and employed. These include current presentations of the state of the data reduction which we anticipate will continue throughout the year and culminate in several more publications. An extensive appendix is used to provide support material such as an experiment history, dissemination items to date (CFE publication, etc.), detailed design drawings, and crew procedures. Despite the simple nature of the experiments and procedures, many of the experimental results may be practically employed to enhance the design of spacecraft engineering

  11. Report on the 4th Conference on Environmental Science of the Carpathian Basin

    International Nuclear Information System (INIS)

    Kiss, A.Z.

    2008-01-01

    Complete text of publication follows. The main organizers of the conference were the Faculty of Science and Technology of the University of Debrecen and the Sapientia - Hungarian University of Transylvania, Faculty of Science and Art, Cluj-Napoca, Romania (the proposer of this series of conferences). The Institute of Nuclear Research of the Hungarian Academy of Sciences (ATOMKI) took part in the organization as its Hertelendi Ede Environmental Research Laboratory and the Ion Beam Application Laboratory are engaged in the study of the environment of the Carpathian Basin. Moreover the Department of Environmental Physics, run jointly by the University of Debrecen and ATOMKI, plays an important role in teaching environmental physics at the university. The conference was held on 28-29 March, 2008, in the building of the Regional Committee of the Hungarian Academy of Sciences (HAS) in Debrecen. The aim of the conference was to bring together scientists and students from different countries, involved in various aspects of environmental science and technology, since the common environmental problems of the Carpathian Basin to be solved make necessary the cooperation between them, living and working in different parts of the basin. The conference gave an opportunity to show the latest results in these fields, and in the same time it was an occasion for the young scientists to be introduced and to exchange experience. The scientific sections were the followings: environmental science and education, environmental chemistry, environmental physics, environmental geography, environmental protection and environmental technology, environmental biology and nature protection, landscape ecology and urban ecology. The number of registered participants (161) was the largest since the beginning (2005) of the conference series. They arrived from five countries (Hungary, Rumania, Slovakia, Croatia and Serbia), several institutions from 27 towns of the Carpathian Basin. The number of oral

  12. Three-dimensional turbulent swirling flow in a cylinder: Experiments and computations

    International Nuclear Information System (INIS)

    Gupta, Amit; Kumar, Ranganathan

    2007-01-01

    Dynamics of the three-dimensional flow in a cyclone with tangential inlet and tangential exit were studied using particle tracking velocimetry (PTV) and a three-dimensional computational model. The PTV technique is described in this paper and appears to be well suited for the current flow situation. The flow was helical in nature and a secondary recirculating flow was observed and well predicted by computations using the RNG k-ε turbulence model. The secondary flow was characterized by a single vortex which circulated around the axis and occupied a large fraction of the cylinder diameter. The locus of the vortex center meandered around the cylinder axis, making one complete revolution for a cylinder aspect ratio of 2. Tangential velocities from both experiments and computations were compared and found to be in good agreement. The general structure of the flow does not vary significantly as the Reynolds number is increased. However, slight changes in all components of velocity and pressure were seen as the inlet velocity is increased. By increasing the inlet aspect ratio it was observed that the vortex meandering changed significantly

  13. Three-dimensional turbulent swirling flow in a cylinder: Experiments and computations

    Energy Technology Data Exchange (ETDEWEB)

    Gupta, Amit [Department of Mechanical, Materials and Aerospace Engineering, University of Central Florida, Orlando, FL 32816 (United States); Kumar, Ranganathan [Department of Mechanical, Materials and Aerospace Engineering, University of Central Florida, Orlando, FL 32816 (United States)]. E-mail: rnkumar@mail.ucf.edu

    2007-04-15

    Dynamics of the three-dimensional flow in a cyclone with tangential inlet and tangential exit were studied using particle tracking velocimetry (PTV) and a three-dimensional computational model. The PTV technique is described in this paper and appears to be well suited for the current flow situation. The flow was helical in nature and a secondary recirculating flow was observed and well predicted by computations using the RNG k-{epsilon} turbulence model. The secondary flow was characterized by a single vortex which circulated around the axis and occupied a large fraction of the cylinder diameter. The locus of the vortex center meandered around the cylinder axis, making one complete revolution for a cylinder aspect ratio of 2. Tangential velocities from both experiments and computations were compared and found to be in good agreement. The general structure of the flow does not vary significantly as the Reynolds number is increased. However, slight changes in all components of velocity and pressure were seen as the inlet velocity is increased. By increasing the inlet aspect ratio it was observed that the vortex meandering changed significantly.

  14. Vibration response of a pipe subjected to two-phase flow: Analytical formulations and experiments

    Energy Technology Data Exchange (ETDEWEB)

    Ortiz-Vidal, L. Enrique, E-mail: leortiz@sc.usp.br [Department of Mechanical Engineering, Sao Carlos School of Engineering, University of Sao Paulo (USP), Av., Trabalhador São-carlense, 400, 13566-970 São Carlos, SP (Brazil); Mureithi, Njuki W., E-mail: njuki.mureithi@polymtl.ca [Department of Mechanical Engineering, Polytechnique Montreal, Département de Géniemécanique 2900, H3T 1J7 Montreal, QC (Canada); Rodriguez, Oscar M.H., E-mail: oscarmhr@sc.usp.br [Department of Mechanical Engineering, Sao Carlos School of Engineering, University of Sao Paulo (USP), Av., Trabalhador São-carlense, 400, 13566-970 São Carlos, SP (Brazil)

    2017-03-15

    Highlights: • Analytical formulations for two-phase flow-induced vibration (2-FIV) are presented. • Standard deviation of acceleration pipe response is a function of the square of shear velocity. • Peak frequency is correlated to hydrodynamic mass and consequently to void fraction. • Dynamic pipe response increases with increasing mixture velocity and void fraction. • Hydrodynamic mass in 2-FIV in horizontal pipe is proportional to mixture density. - Abstract: This paper treats the two-phase flow-induced vibration in pipes. A broad range of two-phase flow conditions, including bubbly, dispersed and slug flow, were tested in a clamped-clamped straight horizontal pipe. The vibration response of both transversal directions for two span lengths was measured. From experimental results, an in-depth discussion on the nature of the flow excitation and flow-parameters influence is presented. The hydrodynamic mass parameter is also studied. Experimental results suggest that it is proportional to mixture density. On the other hand, two analytical formulations were developed and tested against experimental results. One formulation predicts the quadratic trend between standard deviation of acceleration and shear velocity found in experiments. The other formulation indicates that the peak-frequency of vibration response depends strongly on void fraction. It provides accurate predictions of peak-frequency, predicting 97.6% of the data within ±10% error bands.

  15. The effects of gender, flow and video game experience on combat identification training.

    Science.gov (United States)

    Plummer, John Paul; Schuster, David; Keebler, Joseph R

    2017-08-01

    The present study examined the effects of gender, video game experience (VGE), and flow state on multiple indices of combat identification (CID) performance. Individuals were trained on six combat vehicles in a simulation, presented through either a stereoscopic or non-stereoscopic display. Participants then reported flow state, VGE and were tested on their ability to discriminate friend vs. foe and identify both pictures and videos of the trained vehicles. The effect of stereoscopy was not significant. There was an effect of gender across three dependent measures. For the two picture-based measures, the effect of gender was mediated by VGE. Additionally, the effect of gender was moderated by flow state on the identification measures. Overall, the study suggests that gender differences may be overcome by VGE and by achieving flow state. Selection based on these individual differences may be useful for future military simulation. Practitioner Summary: This work investigates the effect of gender, VGE and flow state on CID performance. For three measures of performance, there was a main effect of gender. Gender was mediated by previous VGE on two measures, and gender was moderated by flow state on two measures.

  16. Deformed barchans under alternating flows: Flume experiments and comparison with barchan dunes within Proctor Crater, Mars

    Science.gov (United States)

    Taniguchi, Keisuke; Endo, Noritaka

    2007-10-01

    It is generally considered that barchans, isolated crescentic-shaped dunes, develop where wind is unidirectional and the available sand is insufficient to cover the entire dune field; however, Bishop [Bishop, M.A., 2001. Seasonal variation of crescentic dune morphology and morphometry, Strzelecki Simpson desert, Australia. Earth Surface Process and Landforms 26, 783 791.] observed barchans that developed in areas where winds blow seasonally in opposite directions and described a peculiar deformation feature, the “rear slipface,” that is not found in ordinary barchans. Barchans under such bidirectional flows are poorly understood, and it is necessary to study barchans that formed under many different flow conditions. We conducted flume experiments to investigate the deformation of barchans under alternating water flow, and observed new deformation features in addition to rear slipfaces. We conclude that the deformation of barchans can be categorized into four types, one of which shows morphologies similar to barchans within Proctor Crater, Mars. The deformation type depends on the strength of the reverse flow relative to the forward flow and the absolute velocity of the forward flow. Comparison of our results with barchan dunes within Proctor Crater enable us to qualitatively estimate the wind strength and direction related to dune formation on Mars. These results are in agreement with those of Fenton et al. [Fenton, L.K., Toigo, A.D., Richardson, M.I., 2005. Aeolian processes in Proctor Crater on Mars: Mesoscale modeling of dune-forming winds. Journal of Geophysical Research 110 (E6), E06005.].

  17. MHD flow in multichannel U-bends: Screening experiments and theoretical analysis

    International Nuclear Information System (INIS)

    Reimann, J.; Molokov, S.; Platnieks, I.; Platacis, E.

    1993-02-01

    In electrically coupled multichannel ducts with a U-bend geometry magnetohydrodynamic effects are expected to cause strongly ununiform distributions of flow rates Q i and pressure drops Δp i in the individual channels. A multichannel U-bend geometry is part of the KfK self-cooled Pb-17 Li blanket design (radial-toroidal-radial channels). However, inserts are proposed which isolate electrically the radial channels (not the toroidal ones). To investigate the multichannel effect (MCE), screening experiments were performed at LAS, Riga, with different flow channel geometries and channel numbers between 1 and 5 and using InGaSn as liquid metal. These experiments were carried out with either Δp i ∼const or Q i ∼const. Hartmann Numbers were varied between 0 and ∼1600 (maximum magnetic field strength: 4.1 T) and Interaction Parameters between 0 and 10000. For experiments with electrically conducting walls between the channels, the volume flow rates in the outer channels are significantly larger than those in the inner channels in the experiments with Δp i ∼const. For Q i ∼const., this tendency is reversed, with the highest pressure drop in the middle channel and the lowest in the outer channels. The flow geometry with electrically separated radial channels, similar to the KfK-design result in a fairly even flow rate and pressure drop distribution. The single channels behave approximately like electrically separated channels; no marked MCE occurrs. A theoretical analysis was carried out to describe the MCE for the multichannel U-bend with thin electrically conducting outside walls. This analysis is based on the Core Flow Approximation (CFA), valid for infinitely large Interaction Parameters and Hartmann Numbers. The theory predicts correctly all tendencies observed for the pressure measurements. Moreover, the method is able to describe in detail the flow structure in the toroidal channel. The most essential result is that the flow rate in the layer close to the

  18. Fuel for Fun: a cluster-randomized controlled study of cooking skills, eating behaviors, and physical activity of 4th graders and their families

    Directory of Open Access Journals (Sweden)

    Leslie Cunningham-Sabo

    2016-05-01

    Full Text Available Abstract Background Childhood obesity remains a serious concern in the United States and in many other countries. Direct experience preparing and tasting healthful foods and increasing activity during the school day are promising prevention approaches. Engaging parents and families remains an important challenge. Fuel for Fun: Cooking with Kids Plus Parents and Play is a multi-component school- and family-based intervention for 4th graders and their families intended to promote positive food and activity environments, policies and behaviors at the individual, family and school levels. This paper describes the design and evaluation plan. Methods/Design Four cohorts of 4th-graders and their parents from 8 schools in 2 districts in the same Northern Colorado region are participating in a 4-arm cluster randomized controlled trial. Theory-based Fuel for Fun consists of 5 components delivered over 1 school year: 1 Cooking with Kids - Colorado; an experiential classroom-based cooking and tasting curriculum, 2 Cafeteria Connections; cafeteria-based reinforcements of classroom food experiences using behavioral economic strategies, 3 SPARK active recess; a playground intervention to engage children in moderate to vigorous activity, 4 Fuel for Fun Family; multi-element supports targeting parents to reinforce the 3 school-based components at home, and 5 About Eating; an online interactive program for parents addressing constructs of eating competence and food resource management. Outcomes include child and parent measures of fruit and vegetable preferences and intake, cooking, physical activity, sedentary behaviors and attitudes. School level data assess lunch plate waste and physical activity at recess. In-depth diet and accelerometry assessments are collected with a subsample of parent-child dyads. Data are collected at baseline, immediately post-intervention at 7 months, and at 12 month follow-up. We anticipate recruiting 1320–1584 children and their

  19. Fuel for Fun: a cluster-randomized controlled study of cooking skills, eating behaviors, and physical activity of 4th graders and their families.

    Science.gov (United States)

    Cunningham-Sabo, Leslie; Lohse, Barbara; Smith, Stephanie; Browning, Ray; Strutz, Erin; Nigg, Claudio; Balgopal, Meena; Kelly, Kathleen; Ruder, Elizabeth

    2016-05-26

    Childhood obesity remains a serious concern in the United States and in many other countries. Direct experience preparing and tasting healthful foods and increasing activity during the school day are promising prevention approaches. Engaging parents and families remains an important challenge. Fuel for Fun: Cooking with Kids Plus Parents and Play is a multi-component school- and family-based intervention for 4th graders and their families intended to promote positive food and activity environments, policies and behaviors at the individual, family and school levels. This paper describes the design and evaluation plan. Four cohorts of 4th-graders and their parents from 8 schools in 2 districts in the same Northern Colorado region are participating in a 4-arm cluster randomized controlled trial. Theory-based Fuel for Fun consists of 5 components delivered over 1 school year: 1) Cooking with Kids - Colorado; an experiential classroom-based cooking and tasting curriculum, 2) Cafeteria Connections; cafeteria-based reinforcements of classroom food experiences using behavioral economic strategies, 3) SPARK active recess; a playground intervention to engage children in moderate to vigorous activity, 4) Fuel for Fun Family; multi-element supports targeting parents to reinforce the 3 school-based components at home, and 5) About Eating; an online interactive program for parents addressing constructs of eating competence and food resource management. Outcomes include child and parent measures of fruit and vegetable preferences and intake, cooking, physical activity, sedentary behaviors and attitudes. School level data assess lunch plate waste and physical activity at recess. In-depth diet and accelerometry assessments are collected with a subsample of parent-child dyads. Data are collected at baseline, immediately post-intervention at 7 months, and at 12 month follow-up. We anticipate recruiting 1320-1584 children and their parents over the length of the project. The Fuel

  20. Flow column experiments on the 152Eu migration in systems of loose sediments and water containing humic acids

    International Nuclear Information System (INIS)

    Klotz, D.; Wolf, M.

    2001-01-01

    Humic acid transport of 152 in non-binding loose sediments of different grain sizes was investigated using a groundwater of the tertiary lignite of Northern Germany with a high humic acid concentration. The migration experiments were carried out in flow columns at natural filter flow rates and natural flow lengths [de

  1. Flow Experience During Attentional Training Improves Cognitive Functions in Patients with Traumatic Brain Injury: An Exploratory Case Study

    Directory of Open Access Journals (Sweden)

    Kazuki Yoshida

    2014-12-01

    Conclusion: The results for Patient A suggested that the flow task was more effective than general OT for improving attention deficits. Moreover, the results for Patient B suggested that the flow task was more effective than the control task. Attention training inducing flow experience may thus facilitate improvement of attention.

  2. FOREWORD: 4th International Colloquium on Atomic Spectra and Oscillator Strengths for Astrophysical and Laboratory Plasmas

    Science.gov (United States)

    Leckrone, David S.; Sugar, Jack

    1993-01-01

    or about work currently in progress. This resulted in a number of interesting exchanges, and served to facilitate the coordination of work to be done in the near term. Over the past 15 years we have witnessed the explosive growth of astrophysical spectroscopic observations in both the ultraviolet and infrared bands. Recently, with the launch of the Hubble Space Telescope, the precision and resolution of such data have reached remarkable levels, giving one the sense that the body of atomic data currently to be found in the literature lags far behind what is needed to adequately interpret the observations. Similarly, high temperature laboratory experiments in plasma physics, e.g. fusion energy and x-ray lasers, are demanding larger quantities of atomic data over a wide range of ionization states. Fortunately, the experimental and computational techniques of atomic physics have kept pace. One may cite, for example, the extraordinary precision inherent in recent laboratory work with laser-induced fluorescence spectroscopy and with Fourier transform spectrometers, and for data of highly-ionized atoms, with ion traps and tokamak plasmas. The major challenge is to nurture and support expanded activity in those sub-disciplines of atomic physics that apply such modern techniques to the production of extensive volumes of atomic data, and to reinvigorate such "old fashioned" subjects as the term analysis of new, more accurate laboratory spectra. This series of conferences has a very special character. It is not sponsored or supported by any particular institution, government organization or professional society. The meetings occur only because they serve the common scientific interests of a broad and diverse group of people from around the world. They have had the delightful effect of stimulating professional collaborations and friendships among astronomers, physicists, chemists, mathematicians, and others, who might not have initially realized that they shared so much in

  3. Modernized Approach for Generating Reproducible Heterogeneity Using Transmitted-Light for Flow Visualization Experiments

    Science.gov (United States)

    Jones, A. A.; Holt, R. M.

    2017-12-01

    Image capturing in flow experiments has been used for fluid mechanics research since the early 1970s. Interactions of fluid flow between the vadose zone and permanent water table are of great interest because this zone is responsible for all recharge waters, pollutant transport and irrigation efficiency for agriculture. Griffith, et al. (2011) developed an approach where constructed reproducible "geologically realistic" sand configurations are deposited in sandfilled experimental chambers for light-transmitted flow visualization experiments. This method creates reproducible, reverse graded, layered (stratified) thin-slab sand chambers for point source experiments visualizing multiphase flow through porous media. Reverse-graded stratification of sand chambers mimic many naturally occurring sedimentary deposits. Sandfilled chambers use light as nonintrusive tools for measuring water saturation in two-dimensions (2-D). Homogeneous and heterogeneous sand configurations can be produced to visualize the complex physics of the unsaturated zone. The experimental procedure developed by Griffith, et al. (2011) was designed using now outdated and obsolete equipment. We have modernized this approach with new Parker Deadel linear actuator and programed projects/code for multiple configurations. We have also updated the Roper CCD software and image processing software with the latest in industry standards. Modernization of transmitted-light source, robotic equipment, redesigned experimental chambers, and newly developed analytical procedures have greatly reduced time and cost per experiment. We have verified the ability of the new equipment to generate reproducible heterogeneous sand-filled chambers and demonstrated the functionality of the new equipment and procedures by reproducing several gravity-driven fingering experiments conducted by Griffith (2008).

  4. Guest Editor's introduction: Selected papers from the 4th USENIX Conference on Object-Oriented Technologies and Systems

    Science.gov (United States)

    Sventek, Joe

    1998-12-01

    Hewlett-Packard Laboratories, 1501 Page Mill Road, Palo Alto, CA 94304, USA Introduction The USENIX Conference on Object-Oriented Technologies and Systems (COOTS) is held annually in the late spring. The conference evolved from a set of C++ workshops that were held under the auspices of USENIX, the first of which met in 1989. Given the growing diverse interest in object-oriented technologies, the C++ focus of the workshop eventually became too narrow, with the result that the scope was widened in 1995 to include object-oriented technologies and systems. COOTS is intended to showcase advanced R&D efforts in object-oriented technologies and software systems. The conference emphasizes experimental research and experience gained by using object-oriented techniques and languages to build complex software systems that meet real-world needs. COOTS solicits papers in the following general areas: application of, and experiences with, object-oriented technologies in particular domains (e.g. financial, medical, telecommunication); the architecture and implementation of distributed object systems (e.g. CORBA, DCOM, RMI); object-oriented programming and specification languages; object-oriented design and analysis. The 4th meeting of COOTS was held 27 - 30 April 1998 at the El Dorado Hotel, Santa Fe, New Mexico, USA. Several tutorials were given. The technical program proper consisted of a single track of six sessions, with three paper presentations per session. A keynote address and a provocative panel session rounded out the technical program. The program committee reviewed 56 papers, selecting the best 18 for presentation in the technical sessions. While we solicit papers across the spectrum of applications of object-oriented technologies, this year there was a predominance of distributed, object-oriented papers. The accepted papers reflected this asymmetry, with 15 papers on distributed objects and 3 papers on object-oriented languages. The papers in this special issue are

  5. Salix response to different flow regimes in controlled experiments: first results

    Science.gov (United States)

    Gorla, Lorenzo; Signarbieux, Constant; Buttler, Alexandre; Perona, Paolo

    2013-04-01

    Dams and water management for hydropower production, agriculture and other human activities alter the natural flow regime of rivers. The new river hydrograph components depend on the type of impoundment and the policy of regulation but such a different flow regime will likely affect the riparian environment. The main challenge in order to define sustainable flow releases is to quantify hydrological effects in terms of geomorphology and ecosystem response. A considerable lack of knowledge still affects the link hydrology-ecology and inadequate flow rules (e.g., minimal or residual flows) are consequently still widespread: further research in this direction is urgently required. We present an experiment, which aims to investigate the effects of different water stage regimes on riparian vegetation (salix Viminalis cuttings) development in a temperate region (Switzerland). This work describes the installation setup, together with the first results concerning the first of the two scheduled seasons of campaign. Sixty Salix cuttings were planted in non-cohesive sandy-gravel sediment within 1 meter tall plastic pots installed outside in the EPFL campus. After grouping them in three batteries, the water level within them has been varying following three river regimes simulated by adjusting the water level within the pots by means of an automatic hydraulic system. The three water level regimes reproduce a natural flow regime, a minimum residual flow policy, which only conserves peaks during flooding conditions, and an artificial regime conserving only low frequencies (e.g., seasonality) of the natural dynamic. The natural flow regime of the first battery has been applied for two months to the entire system; the three regimes above said started in June 2012. This triggered a plant response transitory regime, which we monitored by measuring plant growth, soil and atmospheric variables. Particularly, measures concern with branches development leaves photosynthesis and

  6. Are large-scale flow experiments informing the science and management of freshwater ecosystems?

    Science.gov (United States)

    Olden, Julian D.; Konrad, Christopher P.; Melis, Theodore S.; Kennard, Mark J.; Freeman, Mary C.; Mims, Meryl C.; Bray, Erin N.; Gido, Keith B.; Hemphill, Nina P.; Lytle, David A.; McMullen, Laura E.; Pyron, Mark; Robinson, Christopher T.; Schmidt, John C.; Williams, John G.

    2013-01-01

    Greater scientific knowledge, changing societal values, and legislative mandates have emphasized the importance of implementing large-scale flow experiments (FEs) downstream of dams. We provide the first global assessment of FEs to evaluate their success in advancing science and informing management decisions. Systematic review of 113 FEs across 20 countries revealed that clear articulation of experimental objectives, while not universally practiced, was crucial for achieving management outcomes and changing dam-operating policies. Furthermore, changes to dam operations were three times less likely when FEs were conducted primarily for scientific purposes. Despite the recognized importance of riverine flow regimes, four-fifths of FEs involved only discrete flow events. Over three-quarters of FEs documented both abiotic and biotic outcomes, but only one-third examined multiple taxonomic responses, thus limiting how FE results can inform holistic dam management. Future FEs will present new opportunities to advance scientifically credible water policies.

  7. Experiment and Lattice Boltzmann numerical study on nanofluids flow in a micromodel as porous medium

    Science.gov (United States)

    Meghdadi Isfahani, A. H.; Afrand, Masoud

    2017-10-01

    Al2O3 nanofluids flow has been studied in etched glass micromodel which is idealization of porous media by using a pseudo 2D Lattice Boltzmann Method (LBM). The predictions were compared with experimental results. Pressure drop / flow rate relations have been measured for pure water and Al2O3 nanofluids. Because the size of Al2O3 nanoparticles is tiny enough to permit through the pore throats of the micromodel, blockage does not occur and the permeability is independent of the nanofluid volume fraction. Therefore, the nanofluid behaves as a single phase fluid, and a single phase LBM is able to simulate the results of this experiment. Although the flow in micromodels is 3D, we showed that 2D LBM can be used provided an effective viscous drag force, representing the effect of the third dimension, is considered. Good qualitative and quantitative agreement is seen between the numerical and experimental results.

  8. Hydrogen/Oxygen Reactions at High Pressures and Intermediate Temperatures: Flow Reactor Experiments and Kinetic Modeling

    DEFF Research Database (Denmark)

    Hashemi, Hamid; Christensen, Jakob Munkholt; Glarborg, Peter

    A series of experimental and numerical investigations into hydrogen oxidation at high pressures and intermediate temperatures has been conducted. The experiments were carried out in a high pressure laminar flow reactor at 50 bar pressure and a temperature range of 600–900 K. The equivalence ratio......, the mechanism is used to simulate published data on ignition delay time and laminar burning velocity of hydrogen. The flow reactor results show that at reducing, stoichiometric, and oxidizing conditions, conversion starts at temperatures of 750–775 K, 800–825 K, and 800–825 K, respectively. In oxygen atmosphere......, ignition occurs at the temperature of 775–800 K. In general, the present model provides a good agreement with the measurements in the flow reactor and with recent data on laminar burning velocity and ignition delay time....

  9. Short-range dynamics and prediction of mesoscale flow patterns in the MISTRAL field experiment

    Energy Technology Data Exchange (ETDEWEB)

    Weber, R.O.; Kaufmann, P.; Talkner, P. [Paul Scherrer Inst. (PSI), Villigen (Switzerland)

    1997-06-01

    In a limited area of about 50 km by 50 km with complex topography, wind measurements on a dense network were performed during the MISTRAL field experiment in 1991-1992. From these data the characteristic wind fields were identified by an automated classification method. The dynamics of the resulting twelve typical regional flow patterns is studied. It is discussed how transitions between the flow patterns take place and how well the transition probabilities can be described in the framework of a Markov model. Guided by this discussion, a variety of prediction models were tested which allow a short-term forecast of the flow pattern type. It is found that a prediction model which uses forecast information from the synoptic scale has the best forecast skill. (author) 2 figs., 7 refs.

  10. Laying Out Land Parcels and the Oldest Boundary Stone in Croatia from the 4th Century BC

    Directory of Open Access Journals (Sweden)

    Miljenko Solarić

    2009-12-01

    Full Text Available Geographical position of the Chora Pharos (nowadays Starogradsko polje, climate conditions and brief historical development of colonization on the island of Hvar are described in the paper. Also described is how Greek from the island of Paros established the town Pharos (today’s Stari Grad and how they constructed Chora Pharos (today’s Starogradsko polje. They divided the field Starogradsko polje into rectangular parcels with dimensions 1 Greek stage × 5 Greek stage (181 m × 905 m. The large project “Starogradsko polje” demonstrated that one Pharos foot equals 0.3026 m. They used the groma for pegging out orthogonal angles. Finally, there is a photograph of the boundary stone from the Chora Pharos (Starogradsko polje from the 4th century before Christ which is deposited in the Archaeological Museum in Zagreb. This is the oldest boundary stone in Croatia and as geodesists, we can consider it a geodetic monument.

  11. Macracanthorhynchus hirudinaceus Eggs in Canine Coprolite from the Sasanian Era in Iran (4(th/5(th Century CE.

    Directory of Open Access Journals (Sweden)

    Gholamreza Mowlavi

    2015-06-01

    Full Text Available Present paper is the second publication introducing the paleoparasitological findings from animal coprolites obtained from archeological site of Chehrabad salt mine in northwestern Iran. The current archeological site is located in northwest of Iran, dated to the Sassanian Era (4(th/5(th century CE. In the summer 2012 the carnivore coprolite was obtained within the layers in the mine and were thoroughly analyzed for parasites using TSP rehydration technique. Eggs of 0 were successfully retrieved from the examined coprolite and were confidently identified based on reliable references. Identifying of M. hirudinaceus eggs in paleofeces with clear appearance as demonstrated herein, is much due to appropriate preservation condition has been existed in the salt mine .The present finding could be regarded as the oldest acanthocephalan infection in Iran.

  12. An integral metallic-fueled and lead-cooled reactor concept for the 4th generation reactor

    International Nuclear Information System (INIS)

    Santos, Adimir dos; Nascimento, Jamil Alves do

    2002-01-01

    An Integral Lead Reactor (ILR) concept is proposed for the 4th generation reactor to be used in the future. The ILR is loaded with metallic fuel and cooled by lead. It was evaluated in the 300-1500 MWe power range with the Japanese Fast Set 2 cross sections library. This set was tested against several fast benchmarks and the criticality uncertainty was found to be 0.51 %Δk. The reactor is started with U-Zr and changes to the U-TRU-Zr-RE fuel in a stepwise way. In the equilibrium cycle, the burnup reactivity is less than β eff for a core of the order of 300 MWe, pin diameter of 10.4 mm and a pin-pinch to diameter ratio of 1.308. The lead void reactivity is negative for reactor power less than 750 MWe. There is a need to improve the nuclear data for the major actinides. (author)

  13. Determination of Gold Traces in 4th Century B.C. Silver Coins By Neutron Activation Analysis

    International Nuclear Information System (INIS)

    Ronen, Y.; Kubani, G.

    2004-01-01

    A method based on non-destructive neutron activation analysis was developed for measuring traces of gold in silver. This method requires a very small neutron source and, in this study, it was Am-Be of 5μCi. With a small neutron source, the equipment is not expensive and radiation protection problems are reduced. Our method was applied to ancient silver coins from the 4th-3rd centuries B.C. These coins were obols minted in Gaza and Yehud coins minted in Jerusalem. It was found that there is gold in all of them. Their relative gold content was found to be between 7*10 -3 and 8.9*10 - 3 with a relative accuracy of less than 7%. The gold content in silver coins can serve as a ''finger prints' for the origin of the silver

  14. An integral metallic-fueled and lead-cooled reactor concept for the 4th generation reactor

    International Nuclear Information System (INIS)

    Santos, A. dos; Nascimento, J.A. do

    2002-01-01

    An Integral Lead Reactor (ILR) concept is proposed for the 4th generation reactor to be used in the future. The ILR is loaded with metallic fuel and cooled by lead. It was evaluated in the 300-1500 MWe power range with the Japanese Fast Set 2 cross sections library. This set was tested against several fast benchmarks and the criticality uncertainty was found to be 0.51 % Δk. The reactor is started with U-Zr and changes to the U-TRU-Zr-RE fuel in a stepwise way. In the equilibrium cycle, the burnup reactivity is less than β eff for a core of the order of 300 MWe, pin diameter of 10.4 mm and a pin-pitch to diameter ratio of 1.308. The lead void reactivity is negative for reactor power less than 750 MWe. There is a need to improve the nuclear data for the major actinides. (author)

  15. Results of the independent verification of radiological remedial action at 148 East 4th South Street, Monticello, Utah (MS00087)

    International Nuclear Information System (INIS)

    Crutcher, J.W.; Smuin, M.W.

    1989-12-01

    In 1980 the site of a vanadium and uranium mill at Monticello, Utah, was accepted into the US Department of Energy's (DOE's) Surplus Facilities Management Program, with the objectives of restoring the government-owned mill site to safe levels of radioactivity, disposing of or containing the tailings in an environmentally safe manner, and performing remedial actions on off-site (vicinity) properties that had been contaminated by radioactive material resulting from mill operations. During 1984, UNC Geotech, the remedial action contractor designated by DOE, performed remedial action on the vicinity property at 148 East 4th South Street, Monticello, Utah. The Pollutant Assessments Group (PAG) of Oak Ridge National Laboratory was assigned the responsibility of verifying the data supporting the adequacy of remedial action and confirming the site's compliance with DOE guidelines. The PAG found that the site successfully meets the DOE remedial action objectives. Procedures used by PAG are described. 3 refs., 2 tabs

  16. “Apostolic” and “Imperial” discourse in the development of the Roman Primacy in the 4th century

    Directory of Open Access Journals (Sweden)

    Zakharov Georgii

    2016-07-01

    Full Text Available The article is devoted to the evolution of the Roman primacy in the 4th century. The Christianization of the Empire accelerated the process of regional consolidation of the episcopate, but did not lead to the emergence of specific «imperial ecclesiology». At the same time in the 4th century, traditional apostolic ecclesiology has maintained its position both in the West and the East. We can distinguish two different types of the apostolic ecclesiology: locally-historical (the doctrine of St. Irenaeus and Tertullian and universally-hierarchical (the concept of St. Cyprian of Carthage. The first can be fi nd in the works of pope Julius, St. Athanasius and in the letter of the council of Constantinople (382, the second — in the texts of St. Basil the Great and Palladius of Ratiara. At the same time on the council of Serdica (343 Western bishops supported the new “Roman” ecclesiological model. They proclaimed the Roman See as the Chair of Peter the only center of catholic communion and invested it with special legal prerogatives. In fact, this model was the result of ecclesiological synthesis of two early conceptions of apostolicity: the idea of apostolic origins of the Roman Church was connected with the idea of the primacy of Peter as the basis of the Church’s unity. In the future, this conception was adopted by the bishop of Rome. Pope Damasus I (366–384, developing the doctrine of the Roman See as sedes apostolica, actually put principle of Roman primacy above the principle of synodal consensus. Eastern bishops did not support this interpretation of the church order, defending the autonomy of the Eastern Churches. They proclaimed Constantinople New Rome, in fact, denying the uniqueness of the status of the Church of Rome.

  17. Validation of the TRACR3D code for soil water flow under saturated/unsaturated conditions in three experiments

    International Nuclear Information System (INIS)

    Perkins, B.; Travis, B.; DePoorter, G.

    1985-01-01

    Validation of the TRACR3D code in a one-dimensional form was obtained for flow of soil water in three experiments. In the first experiment, a pulse of water entered a crushed-tuff soil and initially moved under conditions of saturated flow, quickly followed by unsaturated flow. In the second experiment, steady-state unsaturated flow took place. In the final experiment, two slugs of water entered crushed tuff under field conditions. In all three experiments, experimentally measured data for volumetric water content agreed, within experimental errors, with the volumetric water content predicted by the code simulations. The experiments and simulations indicated the need for accurate knowledge of boundary and initial conditions, amount and duration of moisture input, and relevant material properties as input into the computer code. During the validation experiments, limitations on monitoring of water movement in waste burial sites were also noted. 5 references, 34 figures, 9 tables

  18. Experiment on smooth, circular cylinders in cross-flow in the critical Reynolds number regime

    Science.gov (United States)

    Miau, J. J.; Tsai, H. W.; Lin, Y. J.; Tu, J. K.; Fang, C. H.; Chen, M. C.

    2011-10-01

    Experiments were conducted for 2D circular cylinders at Reynolds numbers in the range of 1.73 × 105-5.86 × 105. In the experiment, two circular cylinder models made of acrylic and stainless steel, respectively, were employed, which have similar dimensions but different surface roughness. Particular attention was paid to the unsteady flow behaviors inferred by the signals obtained from the pressure taps on the cylinder models and by a hot-wire probe in the near-wake region. At Reynolds numbers pertaining to the initial transition from the subcritical to the critical regimes, pronounced pressure fluctuations were measured on the surfaces of both cylinder models, which were attributed to the excursion of unsteady flow separation over a large circumferential region. At the Reynolds numbers almost reaching the one-bubble state, it was noted that the development of separation bubble might switch from one side to the other with time. Wavelet analysis of the pressure signals measured simultaneously at θ = ±90° further revealed that when no separation bubble was developed, the instantaneous vortex-shedding frequencies could be clearly resolved, about 0.2, in terms of the Strouhal number. The results of oil-film flow visualization on the stainless steel cylinder of the one-bubble and two-bubble states showed that the flow reattachment region downstream of a separation bubble appeared not uniform along the span of the model. Thus, the three dimensionality was quite evident.

  19. Theory of current-driven instability experiments in magnetic Taylor-Couette flows.

    Science.gov (United States)

    Rüdiger, Günther; Schultz, Manfred; Shalybkov, Dima; Hollerbach, Rainer

    2007-11-01

    We consider the linear stability of dissipative magnetic Taylor-Couette flow with imposed toroidal magnetic fields. The inner and outer cylinders can be either insulating or conducting; the inner one rotates, the outer one is stationary. The magnetic Prandtl number can be as small as 10(-5) , approaching realistic liquid-metal values. The magnetic field destabilizes the flow, except for radial profiles of B(phi)(R) close to the current-free solution. The profile with B(in)=B(out) (the most uniform field) is considered in detail. For weak fields the Taylor-Couette flow is stabilized, until for moderately strong fields the m=1 azimuthal mode dramatically destabilizes the flow again so that a maximum value for the critical Reynolds number exists. For sufficiently strong fields (as measured by the Hartmann number) the toroidal field is always unstable, even for the nonrotating case with Re=0 . The electric currents needed to generate the required toroidal fields in laboratory experiments are a few kA if liquid sodium is used, somewhat more if gallium is used. Weaker currents are needed for wider gaps, so a wide-gap apparatus could succeed even with gallium. The critical Reynolds numbers are only somewhat larger than the nonmagnetic values; hence such experiments would work with only modest rotation rates.

  20. Development of the Two Phase Flow Separator Experiment for a Reduced Gravity Aircraft Flight

    Science.gov (United States)

    Golliher, Eric; Gotti, Daniel; Owens, Jay; Gilkey, Kelly; Pham, Nang; Stehno, Philip

    2016-01-01

    The recent hardware development and testing of a reduced gravity aircraft flight experiment has provided valuable insights for the future design of the Two Phase Flow Separator Experiment (TPFSE). The TPFSE is scheduled to fly within the Fluids Integration Rack (FIR) aboard the International Space Station (ISS) in 2020. The TPFSE studies the operational limits of gas and liquid separation of passive cyclonic separators. A passive cyclonic separator utilizes only the inertia of the incoming flow to accomplish the liquid-gas separation. Efficient phase separation is critical for environmental control and life support systems, such as recovery of clean water from bioreactors, for long duration human spaceflight missions. The final low gravity aircraft flight took place in December 2015 aboard NASA's C9 airplane.

  1. Is it all in the game? Flow experience and scientific practices during an INPLACE mobile game

    Science.gov (United States)

    Bressler, Denise M.

    Mobile science learning games show promise for promoting scientific practices and high engagement. Researchers have quantified this engagement according to flow theory. Using an embedded mixed methods design, this study investigated whether an INPLACE mobile game promotes flow experience, scientific practices, and effective team collaboration. Students playing the game (n=59) were compared with students in a business-as-usual control activity (n=120). Using an open-ended instrument designed to measure scientific practices and a self-report flow survey, this study empirically assessed flow and learner's scientific practices. The game players had significantly higher levels of flow and scientific practices. Using a multiple case study approach, collaboration among game teams (n=3 teams) were qualitatively compared with control teams (n=3 teams). Game teams revealed not only higher levels of scientific practices but also higher levels of engaged responses and communal language. Control teams revealed lower levels of scientific practice along with higher levels of rejecting responses and command language. Implications for these findings are discussed.

  2. Optimal Experience and Optimal Identity: A Multinational Study of the Associations Between Flow and Social Identity.

    Science.gov (United States)

    Mao, Yanhui; Roberts, Scott; Pagliaro, Stefano; Csikszentmihalyi, Mihaly; Bonaiuto, Marino

    2016-01-01

    Eudaimonistic identity theory posits a link between activity and identity, where a self-defining activity promotes the strength of a person's identity. An activity engaged in with high enjoyment, full involvement, and high concentration can facilitate the subjective experience of flow. In the present paper, we hypothesized in accordance with the theory of psychological selection that beyond the promotion of individual development and complexity at the personal level, the relationship between flow and identity at the social level is also positive through participation in self-defining activities. Three different samples (i.e., American, Chinese, and Spanish) filled in measures for flow and social identity, with reference to four previously self-reported activities, characterized by four different combinations of skills (low vs. high) and challenges (low vs. high). Findings indicated that flow was positively associated with social identity across each of the above samples, regardless of participants' gender and age. The results have implications for increasing social identity via participation in self-defining group activities that could facilitate flow.

  3. Optimal Experience and Optimal Identity: A Multinational Study of the Associations Between Flow and Social Identity

    Science.gov (United States)

    Mao, Yanhui; Roberts, Scott; Pagliaro, Stefano; Csikszentmihalyi, Mihaly; Bonaiuto, Marino

    2016-01-01

    Eudaimonistic identity theory posits a link between activity and identity, where a self-defining activity promotes the strength of a person’s identity. An activity engaged in with high enjoyment, full involvement, and high concentration can facilitate the subjective experience of flow. In the present paper, we hypothesized in accordance with the theory of psychological selection that beyond the promotion of individual development and complexity at the personal level, the relationship between flow and identity at the social level is also positive through participation in self-defining activities. Three different samples (i.e., American, Chinese, and Spanish) filled in measures for flow and social identity, with reference to four previously self-reported activities, characterized by four different combinations of skills (low vs. high) and challenges (low vs. high). Findings indicated that flow was positively associated with social identity across each of the above samples, regardless of participants’ gender and age. The results have implications for increasing social identity via participation in self-defining group activities that could facilitate flow. PMID:26924995

  4. Refrigerant flow through electronic expansion valve: Experiment and neural network modeling

    International Nuclear Information System (INIS)

    Cao, Xiang; Li, Ze-Yu; Shao, Liang-Liang; Zhang, Chun-Lu

    2016-01-01

    Highlights: • Experimental data from different sources were used in comparison of EEV models. • Artificial neural network in EEV modeling is superior to literature correlations. • Artificial neural network with 4-4-1 structure and S function is recommended. • Artificial neural network is flexible for EEV mass flow rate and opening prediction. - Abstract: Electronic expansion valve (EEV) plays a crucial role in controlling refrigerant mass flow rate of refrigeration or heat pump systems for energy savings. However, complexities in two-phase throttling process and geometry make accurate modeling of EEV flow characteristics more difficult. This paper developed an artificial neural network (ANN) model using refrigerant inlet and outlet pressures, inlet subcooling, EEV opening as ANN inputs, refrigerant mass flow rate as ANN output. Both linear and nonlinear transfer functions in hidden layer were used and compared to each other. Experimental data from multiple sources including in-house experiments of one EEV with R410A were used for ANN training and test. In addition, literature correlations were compared with ANN as well. Results showed that the ANN model with nonlinear transfer function worked well in all cases and it is much accurate than the literature correlations. In all cases, nonlinear ANN predicted refrigerant mass flow rates within ±0.4% average relative deviation (A.D.) and 2.7% standard deviation (S.D.), meanwhile it predicted the EEV opening at 0.1% A.D. and 2.1% S.D.

  5. The Relationship Between Personality Traits, Flow-Experience, and Different Aspects of Practice Behavior of Amateur Vocal Students.

    Science.gov (United States)

    Heller, Katharina; Bullerjahn, Claudia; von Georgi, Richard

    2015-01-01

    Most of the existing studies on musical practice are concerned with instrumentalists only. Since singers are seldom considered in research, the present study is based on an online-sample of amateur vocal students (N = 120; 92 female, 28 male). The study investigated the correlations between personality traits, flow-experience and several aspects of practice characteristics. Personality was represented by the three personality dimensions extraversion, neuroticism and psychoticism, assessed by Eysenck's Personality Profiler as well as the trait form of the Positive and Negative Affect Schedule. 'Flow-experience,' 'self-congruence' and 'fear of losing control over concentration,' assessed by the Practice Flow Inventory, served as variables for flow-experience. The practice motivation was measured by the Practice Motivation Questionnaire in four categories ('self,' 'group,' 'audience,' 'teacher'). In addition, the Practice Behavior Questionnaire was used to provide an insight into the practice situation and behavior of singing students. The results show significant correlations: participants with high extraversion-scores experience significantly more flow than less extraverted persons, whereas lesser flow-experience seems to be related to high neuroticism-scores. Nevertheless, there is no influence in flow-experience concerning singing style ('classical' or 'popular'). The longer the practicing time, the more likely students are to achieve flow-experience. However, older singers tend to have less flow-experience. Consequently, singers seem to differ in their personality and practice behavior compared to other musicians. Most of the findings show that having control over one's instrument is decisive for achieving a performance of high quality, especially for singers. On the other hand, certainty in handling an instrument is essential to arouse a flow-feeling. However, flow-experience seems to be common mainly with amateur singers. In conclusion, this offers a starting

  6. Potential effects of elevated base flow and midsummer spike flow experiments on riparian vegetation along the Green River

    Science.gov (United States)

    Friedman, Jonathan M.

    2018-01-01

    The Upper Colorado River Endangered Fish Recovery Program has requested experimental flow releases from Flaming Gorge Dam for (1) elevated summer base flows to promote larval endangered Colorado pikeminnow, and (2) midsummer spike flows to disadvantage spawning invasive smallmouth bass. This white paper explores the effects of these proposed flow modifications on riparian vegetation and sediment deposition downstream along the Green River. Although modest in magnitude, the elevated base flows and possible associated reductions in magnitude or duration of peak flows would exacerbate a long-term trend of flow stabilization on the Green River that is already leading to proliferation of vegetation including invasive tamarisk along the channel and associated sediment deposition, channel narrowing and channel simplification. Midsummer spike flows could promote establishment of late-flowering plants like tamarisk. Because channel narrowing and simplification threaten persistence and quality of backwater and side channel features needed by endangered fish, the proposed flow modifications could lead to degradation of fish habitat. Channel narrowing and vegetation encroachment could be countered by increases in peak flows or reductions in base flows in some years and by prescription of rapid flow declines following midsummer spike flows. These strategies for reducing vegetation encroachment would need to be balanced with flow

  7. 4th CHINA AUTOMOTIVE

    Institute of Scientific and Technical Information of China (English)

    2002-01-01

    <正> 9-10 September 2002·Shanghai JC Mandarin Hotel, Shanghai CHINA Key issues ■ Industry Updates & Consumer Insights ■ Imported Car v.s. Domestic Car: Combat Price Reduction ■ Sales Networks & Auto Finance ■ Global Sourcing & Supply Chain Management

  8. 4th Optimization Day

    CERN Document Server

    Eberhard, Andrew; Ralph, Daniel; Glover, Barney M

    1999-01-01

    Although the monograph Progress in Optimization I: Contributions from Aus­ tralasia grew from the idea of publishing a proceedings of the Fourth Optimiza­ tion Day, held in July 1997 at the Royal Melbourne Institute of Technology, the focus soon changed to a refereed volume in optimization. The intention is to publish a similar book annually, following each Optimization Day. The idea of having an annual Optimization Day was conceived by Barney Glover; the first of these Optimization Days was held in 1994 at the University of Ballarat. Barney hoped that such a yearly event would bring together the many, but widely dispersed, researchers in Australia who were publishing in optimization and related areas such as control. The first Optimization Day event was followed by similar conferences at The University of New South Wales (1995), The University of Melbourne (1996), the Royal Melbourne Institute of Technology (1997), and The University of Western Australia (1998). The 1999 conference will return to Ballarat ...

  9. 4th Abel Symposium

    CERN Document Server

    Friedlander, Eric; Jahren, Björn; Østvær, Paul

    2009-01-01

    The 2007 Abel Symposium took place at the University of Oslo in August 2007. The goal of the symposium was to bring together mathematicians whose research efforts have led to recent advances in algebraic geometry, algebraic K-theory, algebraic topology, and mathematical physics. A common theme of this symposium was the development of new perspectives and new constructions with a categorical flavor. As the lectures at the symposium and the papers of this volume demonstrate, these perspectives and constructions have enabled a broadening of vistas, a synergy between once-differentiated subjects, and solutions to mathematical problems both old and new.

  10. Particle flow of ceramic breeder pebble beds in bi-axial compression experiments

    International Nuclear Information System (INIS)

    Hermsmeyer, S.; Reimann, J.

    2002-01-01

    Pebble beds of ceramic material are investigated within the framework of developing solid breeder blankets for future fusion power plants. A thermo-mechanical characterisation of such pebble beds is mandatory for understanding the behaviour of pebble beds, and thus the overall blanket, under fusion environment conditions. The mechanical behaviour of pebble beds is typically explored with uni-axial, bi-axial and tri-axial compression experiments. The latter two types of experiment are particularly revealing since they contain explicitly, beyond a compression behaviour of the bed, information on the conditions for pebble flow, i.e. macroscopic relocation, in the pebble bed. (orig.)

  11. Investigation of Groundwater Flow Variations near a Recharge Pond with Repeat Deliberate Tracer Experiments

    Directory of Open Access Journals (Sweden)

    Jordan F Clark

    2014-06-01

    Full Text Available Determining hydraulic connections and travel times between recharge facilities and production wells has become increasingly important for permitting and operating managed aquifer recharge (MAR sites, a water supply strategy that transfers surface water into aquifers for storage and later extraction. This knowledge is critical for examining water quality changes and assessing the potential for future contamination. Deliberate tracer experiments are the best method for determining travel times and identifying preferential flow paths between recharge sites over the time scales of weeks to a few years. This paper compares the results of two deliberate tracer experiments at Kraemer Basin, Orange County, CA, USA. Results from the first experiment, which was conducted in October 1998, showed that a region of highly transmissive sedimentary material extends down gradient from the basin for more than 3 km [1]. Mean groundwater velocities were determined to be approximately 2 km/year in this region based on the arrival time of the tracer center of mass. A second experiment was initiated in January 2008 to determine if travel times from this basin to monitoring and production wells changed during the past decade in response to new recharge conditions. Results indicate that flow near Kraemer Basin was stable, and travel times to most wells determined during both experiments agree within the experimental uncertainty.

  12. Flow-induced vibration analysis of a helical coil steam generator experiment using large eddy simulation

    Energy Technology Data Exchange (ETDEWEB)

    Yuan, Haomin; Solberg, Jerome; Merzari, Elia; Kraus, Adam; Grindeanu, Iulian

    2017-10-01

    This paper describes a numerical study of flow-induced vibration in a helical coil steam generator experiment conducted at Argonne National Laboratory in the 1980s. In the experiment, a half-scale sector model of a steam generator helical coil tube bank was subjected to still and flowing air and water, and the vibrational characteristics were recorded. The research detailed in this document utilizes the multi-physics simulation toolkit SHARP developed at Argonne National Laboratory, in cooperation with Lawrence Livermore National Laboratory, to simulate the experiment. SHARP uses the spectral element code Nek5000 for fluid dynamics analysis and the finite element code DIABLO for structural analysis. The flow around the coil tubes is modeled in Nek5000 by using a large eddy simulation turbulence model. Transient pressure data on the tube surfaces is sampled and transferred to DIABLO for the structural simulation. The structural response is simulated in DIABLO via an implicit time-marching algorithm and a combination of continuum elements and structural shells. Tube vibration data (acceleration and frequency) are sampled and compared with the experimental data. Currently, only one-way coupling is used, which means that pressure loads from the fluid simulation are transferred to the structural simulation but the resulting structural displacements are not fed back to the fluid simulation

  13. Performance Evaluation of the International Space Station Flow Boiling and Condensation Experiment (FBCE) Test Facility

    Science.gov (United States)

    Hasan, Mohammad; Balasubramaniam, R.; Nahra, Henry; Mackey, Jeff; Hall, Nancy; Frankenfield, Bruce; Harpster, George; May, Rochelle; Mudawar, Issam; Kharangate, Chirag R.; hide

    2016-01-01

    A ground-based experimental facility to perform flow boiling and condensation experiments is built in support of the development of the long duration Flow Boiling and Condensation Experiment (FBCE) destined for operation on board of the International Space Station (ISS) Fluid Integrated Rack (FIR). We performed tests with the condensation test module oriented horizontally and vertically. Using FC-72 as the test fluid and water as the cooling fluid, we evaluated the operational characteristics of the condensation module and generated ground based data encompassing the range of parameters of interest to the condensation experiment to be performed on the ISS. During this testing, we also evaluated the pressure drop profile across different components of the fluid subsystem, heater performance, on-orbit degassing subsystem, and the heat loss from different components. In this presentation, we discuss representative results of performance testing of the FBCE flow loop. These results will be used in the refinement of the flight system design and build-up of the FBCE which is scheduled for flight in 2019.

  14. Ground-based PIV and numerical flow visualization results from the Surface Tension Driven Convection Experiment

    Science.gov (United States)

    Pline, Alexander D.; Werner, Mark P.; Hsieh, Kwang-Chung

    1991-01-01

    The Surface Tension Driven Convection Experiment (STDCE) is a Space Transportation System flight experiment to study both transient and steady thermocapillary fluid flows aboard the United States Microgravity Laboratory-1 (USML-1) Spacelab mission planned for June, 1992. One of the components of data collected during the experiment is a video record of the flow field. This qualitative data is then quantified using an all electric, two dimensional Particle Image Velocimetry (PIV) technique called Particle Displacement Tracking (PDT), which uses a simple space domain particle tracking algorithm. Results using the ground based STDCE hardware, with a radiant flux heating mode, and the PDT system are compared to numerical solutions obtained by solving the axisymmetric Navier Stokes equations with a deformable free surface. The PDT technique is successful in producing a velocity vector field and corresponding stream function from the raw video data which satisfactorily represents the physical flow. A numerical program is used to compute the velocity field and corresponding stream function under identical conditions. Both the PDT system and numerical results were compared to a streak photograph, used as a benchmark, with good correlation.

  15. Flow oscillations on the steam control valve in the middle opening condition. Clarification of the phenomena by steam flow experiment and CFD calculation

    International Nuclear Information System (INIS)

    Morita, Ryo; Inada, Fumio

    2006-01-01

    A steam control valve might cause vibrations of piping when the valve opening is in a middle condition. For rationalization of maintenance and management of the plant, the valve should be improved, but it is difficult to understand flow characteristics in detail by experiment because flow around the valve is complex 3D structure and becomes supersonic (M>1). Therefore, it is necessary to clarify the cause of the vibrations and to develop improvements by Computational Fluid Dynamics (CFD) technology. In previous researches, we clarified a mechanism of the pressure fluctuations in the middle opening condition and suggested the way to prevent the pressure fluctuations by experiments and CFD calculations. But, as we used air as a working fluid in our previous research instead of steam that is used in the power plant, we couldn't consider effects of condensation and difference of change of the quantity of state between air and steam. In this report, we have conducted steam flow experiments by multi-purpose steam experiment apparatus 'WISSH' and CFD calculations by steam flow code 'MATIS-SC' to clarify those effects. As a result, in the middle opening condition, we have observed rotating pressure fluctuations in the experiment and valve-attached flow and local high-pressure region in the CFD result. These results show the pressure fluctuations in steam experiments and CFD is same kind of the fluctuations found in air experiment and CFD. (author)

  16. Integrating data and mashup concepts in Hydro-Meteorological Research: the torrential rainfall event in Genoa (4th November 2011) case study.

    Science.gov (United States)

    Bedrina, T.; Parodi, A.; Quarati, A.; Clematis, A.; Rebora, N.; Laiosa, D.

    2012-04-01

    One of the critical issues in Hydro-Meteorological Research (HMR) is a better exploitation of data archives according to a multidisciplinary perspective. Different Earth science databases offer a huge amount of observational data, which often need to be assembled, processed, combined accordingly HM scientists needs. The cooperation between scientists active in HMR and Information and Communication Technologies (ICT) is essential in the development of innovative tools and applications for manipulating, aggregating and re-arranging heterogeneous information in flexible way. In this paper it is described an application devoted to the collection and integration of HM datasets, originated by public or private sources, freely exposed via Web services API. This application uses the mashup, recently become very popular in many fields, (Chow S.-W., 2007) technology concepts. Such methodology means combination of data and/or programs published by external online sources into an integrated experience. Mashup seems to be a promising methodology to respond to the multiple data-related activities into which HM researchers are daily involved (e.g. finding and retrieving high volume data; learning formats and developing readers; extracting parameters; performing filtering and mask; developing analysis and visualization tools). The specific case study of the recent extreme rainfall event, occurred over Genoa in Italy on the 4th November 2011 is shown through the integration of semi-professional weather observational networks as free available data source in addition to official weather networks.

  17. Boron dilution transients during natural circulation flow in PWR-Experiments and CFD simulations

    Energy Technology Data Exchange (ETDEWEB)

    Hoehne, Thomas [Forschungszentrum Dresden-Rossendorf (FZD)-Institute of Safety Research, P.O. Box 510119, D-01314 Dresden (Germany)], E-mail: T.Hoehne@fzd.de; Kliem, Soeren; Rohde, Ulrich; Weiss, Frank-Peter [Forschungszentrum Dresden-Rossendorf (FZD)-Institute of Safety Research, P.O. Box 510119, D-01314 Dresden (Germany)

    2008-08-15

    Coolant mixing in the cold leg, downcomer and the lower plenum of pressurized water reactors is an important phenomenon mitigating the reactivity insertion into the core. Therefore, mixing of the de-borated slugs with the ambient coolant in the reactor pressure vessel was investigated at the four loops 1:5 scaled Rossendorf coolant mixing model (ROCOM) mixing test facility. In particular thermal hydraulics analyses have shown, that weakly borated condensate can accumulate in the pump loop seal of those loops, which do not receive a safety injection. After refilling of the primary circuit, natural circulation in the stagnant loops can re-establish simultaneously and the de-borated slugs are shifted towards the reactor pressure vessel (RPV). In the ROCOM experiments, the length of the flow ramp and the initial density difference between the slugs and the ambient coolant was varied. From the test matrix experiments with 0 resp. 2% density difference between the de-borated slugs and the ambient coolant were used to validate the CFD software ANSYS CFX. To model the effects of turbulence on the mean flow a higher order Reynolds stress turbulence model was employed and a mesh consisting of 6.4 million hybrid elements was utilized. Only the experiments and CFD calculations with modeled density differences show stratification in the downcomer. Depending on the degree of density differences the less dense slugs flow around the core barrel at the top of the downcomer. At the opposite side, the lower borated coolant is entrained by the colder safety injection water and transported to the core. The validation proves that ANSYS CFX is able to simulate appropriately the flow field and mixing effects of coolant with different densities.

  18. Experiments on the flow field physics of confluent boundary layers for high-lift systems

    Science.gov (United States)

    Nelson, Robert C.; Thomas, F. O.; Chu, H. C.

    1994-01-01

    The use of sub-scale wind tunnel test data to predict the behavior of commercial transport high lift systems at in-flight Reynolds number is limited by the so-called 'inverse Reynolds number effect'. This involves an actual deterioration in the performance of a high lift device with increasing Reynolds number. A lack of understanding of the relevant flow field physics associated with numerous complicated viscous flow interactions that characterize flow over high-lift devices prohibits computational fluid dynamics from addressing Reynolds number effects. Clearly there is a need for research that has as its objective the clarification of the fundamental flow field physics associated with viscous effects in high lift systems. In this investigation, a detailed experimental investigation is being performed to study the interaction between the slat wake and the boundary layer on the primary airfoil which is known as a confluent boundary layer. This little-studied aspect of the multi-element airfoil problem deserves special attention due to its importance in the lift augmentation process. The goal of this research is is to provide an improved understanding of the flow physics associated with high lift generation. This process report will discuss the status of the research being conducted at the Hessert Center for Aerospace Research at the University of Notre Dame. The research is sponsored by NASA Ames Research Center under NASA grant NAG2-905. The report will include a discussion of the models that have been built or that are under construction, a description of the planned experiments, a description of a flow visualization apparatus that has been developed for generating colored smoke for confluent boundary layer studies and some preliminary measurements made using our new 3-component fiber optic LDV system.

  19. Prefrontal hemodynamic responses and the degree of flow experience among occupational therapy students during their performance of a cognitive task

    Directory of Open Access Journals (Sweden)

    Kazuki Hirao

    2014-09-01

    Full Text Available Purpose: Although flow experience is positively associated with motivation to learn, the biological basis of flow experience is poorly understood. Accumulation of evidence on the underlying brain mechanisms related to flow is necessary for a deeper understanding of the motivation to learn. The purpose of this study is to investigate the relationship between flow experience and brain function using near-infrared spectroscopy (NIRS during the performance of a cognitive task. Methods: Sixty right-handed occupational therapy (OT students participated in this study. These students performed a verbal fluency test (VFT while 2-channel NIRS was used to assess changes in oxygenated hemoglobin concentration (oxygenated hemoglobin [oxy-Hb] in the prefrontal cortex. Soon after that, the OT students answered the flow questionnaire (FQ to assess the degree of flow experience during the VFT. Results: Average oxy-Hb in the prefrontal cortex had a significant negative correlation with the satisfaction scores on the FQ. Conclusion: Satisfaction during the flow experience correlated with prefrontal hemodynamic suppression. This finding may assist in understanding motivation to learn and related flow experience.

  20. Flume experiments on wind induced flow in static water bodies in the presence of protruding vegetation

    Science.gov (United States)

    Banerjee, Tirtha; Muste, Marian; Katul, Gabriel

    2015-02-01

    The problem of wind-induced flow in inland waters is drawing significant research attention given its relevance to a plethora of applications in wetlands including treatment designs, pollution reduction, and biogeochemical cycling. The present work addresses the role of wind induced turbulence and waves within an otherwise static water body in the presence of rigid and flexible emergent vegetation through flume experimentation and time series analysis. Because no prior example of Particle Imaging Velocimetry (PIV) experiments involving air-water and flexible oscillating components have been found in the literature, a spectral analysis framework is needed and proposed here to guide the analysis involving noise, wave and turbulence separation. The experiments reveal that wave and turbulence effects are simultaneously produced at the air-water interface and the nature of their coexistence is found to vary with different flow parameters including water level, mean wind speed, vegetation density and its flexibility. For deep water levels, signature of fine-scaled inertial turbulence is found at deeper layers of the water system. The wave action appears stronger close to the air-water interface and damped by the turbulence deeper inside the water system. As expected, wave action is found to be dominated in a certain frequency range driven by the wind forcing, while it is also diffused to lower frequencies by means of (wind-induced) oscillations in vegetation. Regarding the mean water velocity, existence of a counter-current flow and its switching to fully forward flow in the direction of the wind under certain combinations of flow parameters were studied. The relative importance of wave and turbulence to the overall energy, degree of anisotropy in the turbulent energy components, and turbulent momentum transport at different depths from the air-water interface and flow combinations were then quantified. The flume experiments reported here differ from previous laboratory

  1. [A development of Byzantine Christian charities during the 4(th)-7(th) centuries and the birth of the hospital].

    Science.gov (United States)

    Nam, Sung Hyun

    2015-04-01

    This study aims to examine the beginning and the development of Christian Charities during the 4(th)-6(th) centuries which would eventually result in the birth of the hospital in modern sense in the first half of the 7(th) century. For this purpose, I looked carefully into various primary sources concerning the early Christian institutions for the poor and the sick. Above all, it's proper to note that the first xenodocheion where hospitality was combined with a systematic caring, is concerned with the Trinitarian debate of the 4(th) century. In 356, Eustathios, one of the leaders of homoiousios group, established xenodocheion to care for the sick and the lepers in Sebaste of Armenia, whereas his opponent Aetios, doctor and leader of the heteroousios party, was reckoned to have combined the medical treatment with his clerical activities. Then, Basil of Caesarea, disciple of Eustathios of Sebaste, also founded in 372 a magnificent benevolent complex named 'Basileias' after its founder. I scrupulously analysed several contemporary materials mentioning the charitable institution of Caesarea which was called alternatively katagogia, ptochotropheion, xenodocheion. John Chrysostome also founded several nosokomeia in Constantinople at the end of the 4(th) century and the beginning of the 5(th) century. Apparently, the contemporary sources mention that doctors existed for these Charities, but there is no sufficient proof that these 'Christian Hospitals,' Basileias or nosokomeia of Constantinople were hospitals in modern sense. Imperial constitutions began to mention ptochotropheion, xenodocheion and orphanotropheion since the second half of the 5(th) century and then some Justinian laws evoked nosokomium, brephotrophia, gerontocomia. These laws reveal that 'Christian Hospitals' were well clarified and deeply rooted in Byzantine society already in these periods. And then, new benevolent institutions emerged in the 6(th) century: nosokomeia for a specific class and

  2. Preliminary three-dimensional potential flow simulation of a five-liter flask air injection experiment

    International Nuclear Information System (INIS)

    Davis, J.E.

    1977-01-01

    The preliminary results of an unsteady three-dimensional potential flow analysis of a five-liter flask air injection experiment (small-scale model simulation of a nuclear reactor steam condensation system) are presented. The location and velocity of the free water surface in the flask as a function of time are determined during pipe venting and bubble expansion processes. The analyses were performed using an extended version of the NASA-Ames Three-Dimensional Potential Flow Analysis System (POTFAN), which uses the vortex lattice singularity method of potential flow analysis. The pressure boundary condition at the free water surface and the boundary condition along the free jet boundary near the pipe exit were ignored for the purposes of the present study. The results of the analysis indicate that large time steps can be taken without significantly reducing the accuracy of the solutions and that the assumption of inviscid flow should not have an appreciable effect on the geometry and velocity of the free water surface. In addition, the computation time required for the solutions was well within acceptable limits

  3. Comparisons of LES and RANS Computations with PIV Experiments on a Cylindrical Cavity Flow

    Directory of Open Access Journals (Sweden)

    Wen-Tao Su

    2013-01-01

    Full Text Available A comparison study on the numerical computations by large eddy simulation (LES and Reynolds-averaged Navier-Stokes (RANS methods with experiment on a cylindrical cavity flow was conducted in this paper. Numerical simulations and particle image velocimetry (PIV measurement were performed for two Reynolds numbers of the flow at a constant aspect ratio of H/R = 2.4 (R is the radius of the cylindrical cavity, and H is liquid level. The three components of velocity were extracted from 100 sequential PIV measured velocity frames with averaging, in order to illustrate the axial jet flow evolution and circulation distribution in the radial direction. The results show that LES can reproduce well the fine structure inside the swirling motions in both the meridional and the horizontal planes, as well as the distributions of velocity components and the circulation, in good agreement with experimental results, while the RANS method only provided a rough trend of inside vortex structure. Based on the analysis of velocity profiles at various locations, it indicates that LES is more suitable for predicting the complex flow characteristics inside complicated three-dimensional geometries.

  4. Further experiments for mean velocity profile of pipe flow at high Reynolds number

    Science.gov (United States)

    Furuichi, N.; Terao, Y.; Wada, Y.; Tsuji, Y.

    2018-05-01

    This paper reports further experimental results obtained in high Reynolds number actual flow facility in Japan. The experiments were performed in a pipe flow with water, and the friction Reynolds number was varied up to Reτ = 5.3 × 104. This high Reynolds number was achieved by using water as the working fluid and adopting a large-diameter pipe (387 mm) while controlling the flow rate and temperature with high accuracy and precision. The streamwise velocity was measured by laser Doppler velocimetry close to the wall, and the mean velocity profile, called log-law profile U+ = (1/κ) ln(y+) + B, is especially focused. After careful verification of the mean velocity profiles in terms of the flow rate accuracy and an evaluation of the consistency of the present results with those from previously measurements in a smaller pipe (100 mm), it was found that the value of κ asymptotically approaches a constant value of κ = 0.384.

  5. Effective Rheology of Two-Phase Flow in Three-Dimensional Porous Media: Experiment and Simulation.

    Science.gov (United States)

    Sinha, Santanu; Bender, Andrew T; Danczyk, Matthew; Keepseagle, Kayla; Prather, Cody A; Bray, Joshua M; Thrane, Linn W; Seymour, Joseph D; Codd, Sarah L; Hansen, Alex

    2017-01-01

    We present an experimental and numerical study of immiscible two-phase flow of Newtonian fluids in three-dimensional (3D) porous media to find the relationship between the volumetric flow rate ( Q ) and the total pressure difference ([Formula: see text]) in the steady state. We show that in the regime where capillary forces compete with the viscous forces, the distribution of capillary barriers at the interfaces effectively creates a yield threshold ([Formula: see text]), making the fluids reminiscent of a Bingham viscoplastic fluid in the porous medium. In this regime, Q depends quadratically on an excess pressure drop ([Formula: see text]). While increasing the flow rate, there is a transition, beyond which the overall flow is Newtonian and the relationship is linear. In our experiments, we build a model porous medium using a column of glass beads transporting two fluids, deionized water and air. For the numerical study, reconstructed 3D pore networks from real core samples are considered and the transport of wetting and non-wetting fluids through the network is modeled by tracking the fluid interfaces with time. We find agreement between our numerical and experimental results. Our results match with the mean-field results reported earlier.

  6. A feeling of flow: exploring junior scientists' experiences with dictation of scientific articles.

    Science.gov (United States)

    Spanager, Lene; Danielsen, Anne Kjaergaard; Pommergaard, Hans-Christian; Burcharth, Jakob; Rosenberg, Jacob

    2013-08-10

    Science involves publishing results, but many scientists do not master this. We introduced dictation as a method of producing a manuscript draft, participating in writing teams and attending a writing retreat to junior scientists in our department. This study aimed to explore the scientists' experiences with this process. Four focus group interviews were conducted and comprised all participating scientists (n = 14). Each transcript was transcribed verbatim and coded independently by two interviewers. The coding structure was discussed until consensus and from this the emergent themes were identified. Participants were 7 PhD students, 5 scholarship students and 2 clinical research nurses. Three main themes were identified: 'Preparing and then letting go' indicated that dictating worked best when properly prepared. 'The big dictation machine' described benefits of writing teams when junior scientists got feedback on both content and structure of their papers. 'Barriers to and drivers for participation' described flow-like states that participants experienced during the dictation. Motivation and a high level of preparation were pivotal to be able to dictate a full article in one day. The descriptions of flow-like states seemed analogous to the theoretical model of flow which is interesting, as flow is usually deemed a state reserved to skilled experts. Our findings suggest that other academic groups might benefit from using the concept including dictation of manuscripts to encourage participants' confidence in their writing skills.

  7. Simulation experiments for hot-leg U-bend two-phase flow phenomena

    International Nuclear Information System (INIS)

    Ishii, M.; Hsu, J.T.; Tucholke, D.; Lambert, G.; Kataoka, I.

    1986-01-01

    In order to study the two-phase natural circulation and flow termination during a small break loss of coolant accident in LWR, simulation experiments have been performed. Based on the two-phase flow scaling criteria developed under this program, an adiabatic hot leg U-bend simulation loop using nitrogen gas and water and a Freon 113 boiling and condensation loop were built. The nitrogen-water system has been used to isolate key hydrodynamic phenomena from heat transfer problems, whereas the Freon loop has been used to study the effect of phase changes and fluid properties. Various tests were carried out to establish the basic mechanism of the flow termination and reestablishment as well as to obtain essential information on scale effects of parameters such as the loop frictional resistance, thermal center, U-bend curvature and inlet geometry. In addition to the above experimental study, a preliminary modeling study has been carried out for two-phase flow in a large vertical pipe at relatively low gas fluxes typical of natural circulation conditions

  8. FIX-II/2032, BWR Pump Trip Experiment 2032, Simulation Mass Flow and Power Transients

    International Nuclear Information System (INIS)

    1988-01-01

    1 - Description of test facility: In the FIX-II pump trip experiments, mass flow and power transients were simulated subsequent to a total loss of power to the recirculation pumps in an internal pump boiling water reactor. The aim was to determine the initial power limit to give dryout in the fuel bundle for the specified transient. In addition, the peak cladding temperature was measured and the rewetting was studied. 2 - Description of test: Pump trip experiment 2032 was a part of test group 2, i.e. the mass flow transient was to simulate the pump coast down with a pump inertia of 11.3 kg.m -2 . The initial power in the 36-rod bundle was 4.44 MW which gave dryout after 1.4 s from the start of the flow transient. A maximum rod cladding temperature of 457 degrees C was measured. Rewetting was obtained after 7.6 s. 3 - Experimental limitations or shortcomings: No ECCS injection systems

  9. Recent experience with testing of parallel disc gate valves under accident flow conditions

    International Nuclear Information System (INIS)

    LaPointe, P.A.; Clayton, J.K.

    1992-01-01

    This paper presents the nuclear valve industry's latest and most extensive valve qualification test program experience. The test program includes a variety of 25 different gate and globe valves. All the test valves are power operated using either air, electric, or gas/hydraulic operators. The valves are categorized in size and pressure class so as to form a group of appropriate parent valve assemblies. Parent valve assembly qualification is used as the basis for qualification of candidate valve assemblies. The parent and candidate valve assemblies are representative of a nuclear plant's safety-related valve applications. The test program was performed in accordance with ANSI B16.41-1983 'Functional Qualification Requirements for Power Operated Active Valve Assemblies for Nuclear Power Plants.' The focus of this paper is on functional valve qualification test experience and specifically flow interruption testing to Annex G of the aforementioned test standard. Results of the flow test are summarized, including the coefficient of friction for each of the gate type valves reported. Information on valve size, pressure class, and actuator are given for all valves in the program. Although all valves performed extremely well, only selected test data are presented. The effects of the speed of operation and the effects of different fluid flow rates as they relate to the coefficient of friction between the valve disc and seat are discussed. The variation in the coefficient of friction based on other variables in the thrust equation, namely, differential pressure area is cited

  10. Validation of two-phase flow code THYC on VATICAN experiment

    International Nuclear Information System (INIS)

    Maurel, F.; Portesse, A.; Rimbert, P.; Thomas, B.

    1997-01-01

    As part of a comprehensive program for THYC validation (THYC is a 3-dimensional two-phase flow computer code for PWR core configuration), an experimental project > has been initiated by the Direction des Etudes et Recherches of Electricite de France. Two mock-ups tested in Refrigerant-114, VATICAN-1 (with simple space grids) and VATICAN-2 (with mixing grids) were set up to investigate void fraction distributions using a single beam gamma densitometer. First, experiments were conducted with the VATICAN-1 mock-up. A set of constitutive laws to be used in rod bundles was determined but some doubts still remain for friction losses closure laws for oblique flow over tubes. From VATICAN-2 tests, calculations were performed using the standard set of correlations. Comparison with the experimental data shows an underprediction of void fraction by THYC in disturbed regions. Analyses highlight the poor treatment of axial relative velocity in these regions. A fitting of the radial and axial relative velocity values in the disturbed region improves the prediction of void fraction by the code but without any physical explanation. More analytical experiments should be carried out to validate friction losses closure laws for oblique flows and relative velocity downstream of a mixing grid. (author)

  11. Validation of two-phase flow code THYC on VATICAN experiment

    Energy Technology Data Exchange (ETDEWEB)

    Maurel, F.; Portesse, A.; Rimbert, P.; Thomas, B. [EDF/DER, Dept. TTA, 78 - Chatou (France)

    1997-12-31

    As part of a comprehensive program for THYC validation (THYC is a 3-dimensional two-phase flow computer code for PWR core configuration), an experimental project <> has been initiated by the Direction des Etudes et Recherches of Electricite de France. Two mock-ups tested in Refrigerant-114, VATICAN-1 (with simple space grids) and VATICAN-2 (with mixing grids) were set up to investigate void fraction distributions using a single beam gamma densitometer. First, experiments were conducted with the VATICAN-1 mock-up. A set of constitutive laws to be used in rod bundles was determined but some doubts still remain for friction losses closure laws for oblique flow over tubes. From VATICAN-2 tests, calculations were performed using the standard set of correlations. Comparison with the experimental data shows an underprediction of void fraction by THYC in disturbed regions. Analyses highlight the poor treatment of axial relative velocity in these regions. A fitting of the radial and axial relative velocity values in the disturbed region improves the prediction of void fraction by the code but without any physical explanation. More analytical experiments should be carried out to validate friction losses closure laws for oblique flows and relative velocity downstream of a mixing grid. (author)

  12. The Effects of Autonomy-Supportive and Controlling Teaching Behaviour in Biology Lessons with Primary and Secondary Experiences on Students' Intrinsic Motivation and Flow-Experience

    Science.gov (United States)

    Hofferber, Natalia; Basten, Melanie; Großmann, Nadine; Wilde, Matthias

    2016-01-01

    Self-Determination Theory and Flow Theory propose that perceived autonomy fosters the positive qualities of motivation and flow-experience. Autonomy-support can help to maintain students' motivation in very interesting learning activities and may lead to an increase in the positive qualities of motivation in less interesting learning activities.…

  13. Application of the FUN3D Unstructured-Grid Navier-Stokes Solver to the 4th AIAA Drag Prediction Workshop Cases

    Science.gov (United States)

    Lee-Rausch, Elizabeth M.; Hammond, Dana P.; Nielsen, Eric J.; Pirzadeh, S. Z.; Rumsey, Christopher L.

    2010-01-01

    FUN3D Navier-Stokes solutions were computed for the 4th AIAA Drag Prediction Workshop grid convergence study, downwash study, and Reynolds number study on a set of node-based mixed-element grids. All of the baseline tetrahedral grids were generated with the VGRID (developmental) advancing-layer and advancing-front grid generation software package following the gridding guidelines developed for the workshop. With maximum grid sizes exceeding 100 million nodes, the grid convergence study was particularly challenging for the node-based unstructured grid generators and flow solvers. At the time of the workshop, the super-fine grid with 105 million nodes and 600 million elements was the largest grid known to have been generated using VGRID. FUN3D Version 11.0 has a completely new pre- and post-processing paradigm that has been incorporated directly into the solver and functions entirely in a parallel, distributed memory environment. This feature allowed for practical pre-processing and solution times on the largest unstructured-grid size requested for the workshop. For the constant-lift grid convergence case, the convergence of total drag is approximately second-order on the finest three grids. The variation in total drag between the finest two grids is only 2 counts. At the finest grid levels, only small variations in wing and tail pressure distributions are seen with grid refinement. Similarly, a small wing side-of-body separation also shows little variation at the finest grid levels. Overall, the FUN3D results compare well with the structured-grid code CFL3D. The FUN3D downwash study and Reynolds number study results compare well with the range of results shown in the workshop presentations.

  14. Flow and transport at the Las Cruces trench site: Experiment IIb

    International Nuclear Information System (INIS)

    Vinson, J.; Hills, R.G.; Wierenga, P.J.; Young, M.H.

    1997-07-01

    The US Nuclear Regulatory Commission (NRC) has been directed by Congress in the Low Level Waste Policy Act of 1980 to develop regulatory guidance and assist the individual states and compacts in siting and assessing future low level radioactive waste (LLW) disposal facilities. Three water flow and solute transport experiments were performed as part of a comprehensive field trench study near Las Cruces, New Mexico to test deterministic and stochastic models of vadose zone flow and transport. This report presents partial results from the third experiment (experiment IIb). Experiments IIa and b were conducted on the North side of the trench, on a plot 1.22 m wide by 12 m long, perpendicular to the trench. The area was drip irrigated during two time periods with water containing a variety of tracers. The advance of the water front during the two irrigation episodes was measured with tensiometers and neutron probes. Solute front positions were determined from soil solution sampling through suction samplers and from disturbed sampling. The results from experiment IIb show predominantly downward water movement through the layered unsaturated soil, as evidenced from neutron probe data and gravimetric sampling. Tritium plumes were only half as deep and half as wide as the water plumes at 310 days after the beginning of experiment IIb. Chromium, applied as Cr(VI), moved a readily as, and similar to tritium, but there was a loss of mass due to reduction of Cr(VI) to Cr(III). Chloride and nitrate, initially present at high concentrations in the soil solution, were displaced by the low concentration irrigation water, resulting in chloride and nitrate concentration distributions that looked like negative images of the tritium distributions. The extensive data presented should serve well as a data base for model testing

  15. Flow and transport at the Las Cruces trench site: Experiment IIb

    Energy Technology Data Exchange (ETDEWEB)

    Vinson, J.; Hills, R.G. [New Mexico State Univ., Las Cruces, NM (United States); Wierenga, P.J.; Young, M.H. [Arizona Univ., Tucson, AZ (United States). Dept. of Soil and Water Science

    1997-07-01

    The US Nuclear Regulatory Commission (NRC) has been directed by Congress in the Low Level Waste Policy Act of 1980 to develop regulatory guidance and assist the individual states and compacts in siting and assessing future low level radioactive waste (LLW) disposal facilities. Three water flow and solute transport experiments were performed as part of a comprehensive field trench study near Las Cruces, New Mexico to test deterministic and stochastic models of vadose zone flow and transport. This report presents partial results from the third experiment (experiment IIb). Experiments IIa and b were conducted on the North side of the trench, on a plot 1.22 m wide by 12 m long, perpendicular to the trench. The area was drip irrigated during two time periods with water containing a variety of tracers. The advance of the water front during the two irrigation episodes was measured with tensiometers and neutron probes. Solute front positions were determined from soil solution sampling through suction samplers and from disturbed sampling. The results from experiment IIb show predominantly downward water movement through the layered unsaturated soil, as evidenced from neutron probe data and gravimetric sampling. Tritium plumes were only half as deep and half as wide as the water plumes at 310 days after the beginning of experiment IIb. Chromium, applied as Cr(VI), moved a readily as, and similar to tritium, but there was a loss of mass due to reduction of Cr(VI) to Cr(III). Chloride and nitrate, initially present at high concentrations in the soil solution, were displaced by the low concentration irrigation water, resulting in chloride and nitrate concentration distributions that looked like negative images of the tritium distributions. The extensive data presented should serve well as a data base for model testing.

  16. Change of neutron flow sensors effectiveness in the course of reactor experiments

    International Nuclear Information System (INIS)

    Kurpesheva, A.M.; Kotov, V.M.; Zhotabaev, Zh.R.

    2007-01-01

    Full text: IGR reactor is a reactor of thermal capacity type. During the operation, uranium-graphite core can be heated up to 1500 deg. C and reactivity can be changed considerably. Core dimensions are comparatively small. Amount of control rods, providing required reactivity, is not big as well. Increasing of core temperature leads to the rise of neutrons path length in its basic material - graphite. Change of temperature is not even. All this causes the non-conservation of neutron flows ratio in irradiated sample and in the place of reactor power sensors installation. Deviations in this ratio were registered during the number of reactor experiments. Empiric corrections can be introduced in order to decrease influence of change of neutron flow effectiveness upon provision of required parameters of investigated matters load. However, dependence of these corrections upon many factors can lead to the increasing of instability of process control. Previous experiment-calculated experiments showed inequality of neutron field in the place of sensors location (up to tens of percent), low effectiveness of experimental works, carried out without access to the individual reactor laying elements. Imperfection during the experiment was an idea of possibility to connect distribution of out of reactor neutron flow and control rods position. Subsequent analysis showed that for the development of representative phenomenon model it is necessary to take into account reactor operation dynamic subject to unevenness of heating of individual laying parts. Elemental calculations showed that temperature laying effects in the change of neutron outer field are great. Algorithm of calculations for the change of outer filed and field of investigated fabrication includes calculation of neutron-physic reactor characteristics interlacing with calculations of thermal-physic reactor characteristics, providing correlation of temperature fields for neutron-physic calculations. In the course of such

  17. Studies of Flow in Ionized Gas: Historical Perspective, Contemporary Experiments, and Applications

    International Nuclear Information System (INIS)

    Popovic, S.; Vuskovic, L.

    2007-01-01

    Since the first observations that a very small ionized fraction (order of 1 ppm) could strongly affect the gas flow, numerous experiments with partially or fully wall-free discharges have demonstrated the dispersion of shock waves, the enhancement of lateral forces in the flow, the prospects of levitation, and other aerodynamic effects with vast potential of application. A review of physical effects and observations are given along with current status of their interpretation. Special attention will be given to the physical problems of energy efficiency in generating wall-free discharges and the phenomenology of filamentary discharges. Comments and case examples are given on the current status of availability of necessary data for modelling and simulation of the aerodynamic phenomena in weakly ionized gas

  18. Multiphase flow experiments, mathematical modeling and numerical simulation of the water - gas - solute movement

    Science.gov (United States)

    Li, Y.; Ma, X.; Su, N.

    2013-12-01

    The movement of water and solute into and through the vadose zone is, in essence, an issue of immiscible displacement in pore-space network of a soil. Therefore, multiphase flow and transport in porous media, referring to three medium: air, water, and the solute, pose one of the largest unresolved challenges for porous medium fluid seepage. However, this phenomenon has always been largely neglected. It is expected that a reliable analysis model of the multi-phase flow in soil can truly reflect the process of natural movement about the infiltration, which is impossible to be observed directly. In such cases, geophysical applications of the nuclear magnetic resonance (NMR) provides the opportunity to measure the water movements into soils directly over a large scale from tiny pore to regional scale, accordingly enable it available both on the laboratory and on the field. In addition, the NMR provides useful information about the pore space properties. In this study, we proposed both laboratory and field experiments to measure the multi-phase flow parameters, together with optimize the model in computer programming based on the fractional partial differential equations (fPDE). In addition, we establish, for the first time, an infiltration model including solute flowing with water, which has huge influence on agriculture and soil environment pollution. Afterwards, with data collected from experiments, we simulate the model and analyze the spatial variability of parameters. Simulations are also conducted according to the model to evaluate the effects of airflow on water infiltration and other effects such as solute and absorption. It has significant meaning to oxygen irrigation aiming to higher crop yield, and shed more light into the dam slope stability. In summary, our framework is a first-time model added in solute to have a mathematic analysis with the fPDE and more instructive to agriculture activities.

  19. Particle flow of ceramic breeder pebble beds in bi-axial compression experiments

    International Nuclear Information System (INIS)

    Hermsmeyer, S.; Reimann, J.

    2002-01-01

    Pebble beds of Tritium breeding ceramic material are investigated within the framework of developing solid breeder blankets for future nuclear fusion power plants. For the thermo-mechanical characterisation of such pebble beds, bed compression experiments are the standard tools. New bi-axial compression experiments on 20 and 30 mm high pebble beds show pebble flow effects much more pronounced than in previous 10 mm beds. Owing to the greater bed height, conditions are reached where the bed fails in cross direction and unhindered flow of the pebbles occurs. The paper presents measurements for the orthosilicate and metatitanate breeder materials that are envisaged to be used in a solid breeder blanket. The data are compared with calculations made with a Drucker-Prager soil model within the finite-element code ABAQUS, calibrated with data from other experiments. It is investigated empirically whether internal bed friction angles can be determined from pebble beds of the considered heights, which would simplify, and broaden the data base for, the calibration of the Drucker-Prager pebble bed models

  20. Communicating Science to Impact Learning? A Phenomenological Inquiry into 4th and 5th Graders' Perceptions of Science Information Sources

    Science.gov (United States)

    Gelmez Burakgazi, Sevinc; Yildirim, Ali; Weeth Feinstein, Noah

    2016-04-01

    Rooted in science education and science communication studies, this study examines 4th and 5th grade students' perceptions of science information sources (SIS) and their use in communicating science to students. It combines situated learning theory with uses and gratifications theory in a qualitative phenomenological analysis. Data were gathered through classroom observations and interviews in four Turkish elementary schools. Focus group interviews with 47 students and individual interviews with 17 teachers and 10 parents were conducted. Participants identified a wide range of SIS, including TV, magazines, newspapers, internet, peers, teachers, families, science centers/museums, science exhibitions, textbooks, science books, and science camps. Students reported using various SIS in school-based and non-school contexts to satisfy their cognitive, affective, personal, and social integrative needs. SIS were used for science courses, homework/project assignments, examination/test preparations, and individual science-related research. Students assessed SIS in terms of the perceived accessibility of the sources, the quality of the content, and the content presentation. In particular, some sources such as teachers, families, TV, science magazines, textbooks, and science centers/museums ("directive sources") predictably led students to other sources such as teachers, families, internet, and science books ("directed sources"). A small number of sources crossed context boundaries, being useful in both school and out. Results shed light on the connection between science education and science communication in terms of promoting science learning.

  1. Advances in urea cycle neuroimaging: Proceedings from the 4th International Symposium on urea cycle disorders, Barcelona, Spain, September 2013.

    Science.gov (United States)

    Pacheco-Colón, Ileana; Fricke, Stanley; VanMeter, John; Gropman, Andrea L

    2014-01-01

    Our previous imaging research performed as part of a Urea Cycle Rare Disorders Consortium (UCRDC) grant, has identified specific biomarkers of neurologic injury in ornithine transcarbamylase deficiency, OTCD. While characterization of mutations can be achieved in most cases, this information does not necessarily predict the severity of the underlying neurological syndrome. The biochemical consequences of any mutation may be modified additionally by a large number of factors, including contributions of other enzymes and transport systems that mediate flux through the urea cycle, diet and other environmental factors. These factors likely vary from one patient to another, and they give rise to heterogeneity of clinical severity. Affected cognitive domains include non-verbal learning, fine motor processing, reaction time, visual memory, attention, and executive function. Deficits in these capacities may be seen in symptomatic patients, as well as asymptomatic carriers with normal IQ and correlate with variances in brain structure and function in these patients. Using neuroimaging we can identify biomarkers that reflect the downstream impact of UCDs on cognition. This manuscript is a summary of the presentation from the 4th International Consortium on urea cycle disorders held in, Barcelona, Spain, September 2, 2014. Copyright © 2014 Elsevier Inc. All rights reserved.

  2. Cigarette smoking, pocket money and socioeconomic status: results from a national survey of 4th form students in 2000.

    Science.gov (United States)

    Scragg, Robert; Laugesen, Murray; Robinson, Elizabeth

    2002-07-26

    To investigate whether pocket money amount and socio-economic status are risk factors for smoking in 14 and 15 year old children. This was a national cross-sectional survey of 4th form students who answered an anonymous self-administered questionnaire in November 2000. Socio-economic status was determined from the Ministry of Education school socio-economic deciles. Questionnaires from 14793 girls and 14577 boys were analysed. Socioeconomic status (SES) was inversely associated with smoking prevalence in girls only (ppocket money than those in high SES decile schools (ppocket money >$30, $21-30, or $11-20, the adjusted relative risks for smoking > or = monthly were 1.73 (95% CI 1.61, 1.85), 1.48 (1.35, 1.62), and 1.15 (1.03, 1.28) in girls, and 1.57 (1.46, 1.70), 1.32 (1.19, 1.46), and 1.11 (1.00, 1.23) in boys, respectively. The proportion of smokers purchasing cigarettes increased with amount of pocket money received in the last 30 days (ppocket money amount in adolescents. This finding has important public health significance, but further research is required to determine if the association is causal.

  3. Particle content and degrees of freedom of a gravitational field in 4th order theories of gravity

    International Nuclear Information System (INIS)

    Moebius, K.; Akademie der Wissenschaften der DDR, Potsdam-Babelsberg. Einstein-Laboratorium fuer Theoretische Physik)

    1988-01-01

    In gravitational theories of 4-th order, the influence of certain properties of the field equations (tracelessness, conformal invariance, scale invariance respectively their breaking) for the 'particle content' (number of degrees of freedom, mass, spin) is investigated. Using the plane-wave ansatz valid in linearized theory it is possible to determine the mass content of the theory, but one cannot get assertions about the number of degrees of freedom and the spin states corresponding to the field quanta. In the linearized theory, this can be done with a spin projection formalism. Using the Cauchy initial value problem and a counting method first developed by Einstein one can get, however, a useful definition of the concept of the degrees of freedom for the full nonlinear theory. This is due to the fact that this method allows to incorporate the concrete structure of the field equations (and thus their nonlinearities). Analysing different general-relativistic field theories via these approaches the influence of the various structures of nonlinearities is discussed. It is, in particular, shown that those results obtained by the spin projection formalism can be reproduced by 'nonlinear methods'. (author)

  4. Identification of DRG-1 As a Melanoma-Associated Antigen Recognized by CD4+ Th1 Cells.

    Directory of Open Access Journals (Sweden)

    Yukiko Kiniwa

    Full Text Available Immunotherapy has emerged as a promising strategy for the treatment of metastatic melanoma. Clinical studies have demonstrated the feasibility of cancer immunotherapy using tumor antigens recognized by CD8(+ T cells. However, the overall immune responses induced by these antigens are too weak and transient to induce tumor regression in the majority of patients who received immunization. A growing body of evidence suggests that CD4(+ T helper (Th cells play an important role in antitumor immunity. Therefore, the identification of MHC class II-restricted tumor antigens capable of stimulating CD4(+ T cells may provide opportunities for developing effective cancer vaccines. To this end, we describe the identification of developmentally regulated GTP-binding protein 1 (DRG-1 as a melanoma-associated antigen recognized by HLA-DR11-restricted CD4(+ Th1 cells. Epitope mapping analysis showed that the DRG1248-268 epitope of DRG-1 was required for T cell recognition. Reverse transcription-polymerase chain reaction revealed that DRG-1 was highly expressed in melanoma cell lines but not in normal tissues. DRG-1 knockdown by lentiviral-based shRNA suppressed melanoma cell proliferation and soft agar colony formation. Taken together, these data suggest that DRG-1 plays an important role in melanoma cell growth and transformation, indicating that DRG1 may represent a novel target for CD4(+ T cell-mediated immunotherapy in melanoma.

  5. Identification of DRG-1 As a Melanoma-Associated Antigen Recognized by CD4+ Th1 Cells.

    Science.gov (United States)

    Kiniwa, Yukiko; Li, Jiang; Wang, Mingjun; Sun, Chuang; Lee, Jeffrey E; Wang, Rong-Fu; Wang, Helen Y

    2015-01-01

    Immunotherapy has emerged as a promising strategy for the treatment of metastatic melanoma. Clinical studies have demonstrated the feasibility of cancer immunotherapy using tumor antigens recognized by CD8(+) T cells. However, the overall immune responses induced by these antigens are too weak and transient to induce tumor regression in the majority of patients who received immunization. A growing body of evidence suggests that CD4(+) T helper (Th) cells play an important role in antitumor immunity. Therefore, the identification of MHC class II-restricted tumor antigens capable of stimulating CD4(+) T cells may provide opportunities for developing effective cancer vaccines. To this end, we describe the identification of developmentally regulated GTP-binding protein 1 (DRG-1) as a melanoma-associated antigen recognized by HLA-DR11-restricted CD4(+) Th1 cells. Epitope mapping analysis showed that the DRG1248-268 epitope of DRG-1 was required for T cell recognition. Reverse transcription-polymerase chain reaction revealed that DRG-1 was highly expressed in melanoma cell lines but not in normal tissues. DRG-1 knockdown by lentiviral-based shRNA suppressed melanoma cell proliferation and soft agar colony formation. Taken together, these data suggest that DRG-1 plays an important role in melanoma cell growth and transformation, indicating that DRG1 may represent a novel target for CD4(+) T cell-mediated immunotherapy in melanoma.

  6. [Associated factors to availability and use of electronic media in children from preschool to 4th grade].

    Science.gov (United States)

    Camargo, Diana Marina; Orozco, Luis Carlos

    2013-01-01

    The increased availability of electronic media has changed the behavior in children and young people by encouraging sedentary lifestile, with health effects from a very young age. To characterize the availability and use of electronic media and its associated factors in children from preschool through 4 th grade. A cross-sectional study with cluster sampling was carried out. Parents filled out the demographic survey, the availability and use of electronic media at home and in the child´s room. Log-binomial regression models were applied to estimate prevalence ratios adjusted for the sampling. Seven hundred and ten parents answered. The average age of the children was 6.7 years and 49.7% were male. Factors such as the mother working out of the house and family income were positively associated with the availability of electronic media at home and in the child´s room. The availability of a TV, computer and console in the child´s room, contributes to longer use of these electronic media. Both, the male gender and age of the child, were positively associated with the availability and use of electronic media. This is the first study in Colombia that reports the availability and use of electronic media in children. It is clear that modern life encourages sedentary behavior from the earliest years of life, which has been associated with health problems from early childhood. Intervention studies are needed aimed at reducing these behaviors in our context.

  7. Internal fixation of proximal fractures of the 2nd and 4th metacarpal and metatarsal bones using bioabsorbable screws.

    Science.gov (United States)

    Mageed, M; Steinberg, T; Drumm, N; Stubbs, N; Wegert, J; Koene, M

    2018-03-01

    Fractures involving the proximal one-third of the splint bone are relatively rare and are challenging to treat. A variety of management techniques have been reported in the literature. The aim of this retrospective case series was to describe the clinical presentation and evaluate the efficacy of bioabsorbable polylactic acid screws in internal fixation of proximal fractures of the 2nd and 4th metacarpal and metatarsal bones in horses. The medical records, diagnostic images and outcome of all horses diagnosed with a proximal fracture of the splint bones and treated with partial resection and internal fixation of the proximal stump using bioabsorbable polylactic acid screws between 2014 and 2015 were reviewed. Eight horses met the inclusion criteria. The results showed that there were no complications encountered during screw placement or postoperatively. Six horses returned to full work 3 months after the operation and two horses remained mildly lame. On follow-up radiographs 12 months postoperatively (n = 2) the screws were not completely absorbed. The screws resulted in a cone-shaped radiolucency, which was progressively replaced from the outer margins by bone sclerosis. The use of bioabsorbable screws for fixation of proximal fractures of the splint bone appears to be a safe and feasible technique and may offer several advantages over the use of traditional metallic implants. © 2018 Australian Veterinary Association.

  8. Monitoring of debris flows and landslides by wired and wireless systems. Experiences from the Catalan Pyrenees.

    Science.gov (United States)

    Hürlimann, Marcel; Abancó, Clàudia; Moya, José; Vilajosana, Ignasi; Llosa, Jordi

    2013-04-01

    Sophisticated monitoring of landslides for research purpose has started in the 1990thies in the Catalan Pyrenees. Since then several types of mass movements (large landslides, debris flows, shallow landslides and rock falls) and multiples techniques have been applied. In this contribution, special attention will be given to the debris-flow monitoring system installed since summer 2009 in the Rebaixader catchment, Central Pyrenees. The monitoring system has continuously been improved during the last years and nowadays includes devices studying the three major aspects: 1) initiation, 2) flow dynamics, and 3) accumulation. While some parts of the monitoring network include a traditional wired system, the newer parts were installed using low-power wireless devices. Two major aspects will be discussed. First, results of the Rebaixader monitoring site will be presented. Second, experience regarding the monitoring will be evaluated focussing on technical aspects and the comparison between wired and wireless techniques. In the Rebaixader catchment, 6 debris flows and 11 debris floods were observed between August 2009 and October 2012. Surprisingly, also 4 major rock falls were recorded. The rainfall analysis shows that the debris flows were triggered by short, high-intensity rainstorms with a preliminary threshold of about 15 mm during 1 hour. In addition, there was observed a positive trend between event volume and rainfall amount or intensity. The analysis of the ground vibration signals shows significant differences between the time series recorded at the different geophones. These differences are associated with the geophone location in the channel (distance and material), the mounting or the data acquisition system. For instance, the most downstream geophone, installed in bedrock, shows the clearest debris-flows vibration time series, while the uppermost is the most reliable regarding the detection of rockfalls. An evaluation of wired versus wireless monitoring

  9. Analysis of ASTEC-Na capabilities for simulating a loss of flow CABRI experiment

    International Nuclear Information System (INIS)

    Flores y Flores, A.; Matuzas, V.; Perez-Martin, S.; Bandini, G.; Ederli, S.; Ammirabile, L.; Pfrang, W.

    2016-01-01

    Highlights: • ASTEC-Na results for CABRI BI1 test have been compared with experimental data. • The ASTEC-Na calculations reached the boiling onset within the error bar of the test. • The coolant axial profile in ASTEC-Na fit almost perfectly with the experimental data. • All the calculations have a good agreement with the two-phase front downwards. • All the calculations have a worse agreement with the two-phase front upwards. - Abstract: This paper presents simulation results of the CABRI BI1 test using the code ASTEC-Na, currently under development, as well as a comparison of the results with available experimental data. The EU-JASMIN project (7th FP of EURATOM) centres on the development and validation of the new severe accident analysis code ASTEC-Na (Accident Source Term Evaluation Code) for sodium-cooled fast reactors whose owner and developer is IRSN. A series of experiments performed in the past (CABRI/SCARABEE experiments) and new experiments to be conducted in the new experimental sodium facility KASOLA have been chosen to validate the developed ASTEC-Na code. One of the in-pile experiments considered for the validation of ASTEC-Na thermal–hydraulic models is the CABRI BI1 test, a pure loss-of-flow transient using a low burnup MOX fuel pin. The experiment resulted in a channel voiding as a result of the flow coast-down leading to clad melting. Only some fuel melting took place. Results from the analysis of this test using SIMMER and SAS-SFR codes are also presented in this work to check their suitability for further code benchmarking purposes.

  10. Robust flow stability: Theory, computations and experiments in near wall turbulence

    Science.gov (United States)

    Bobba, Kumar Manoj

    Helmholtz established the field of hydrodynamic stability with his pioneering work in 1868. From then on, hydrodynamic stability became an important tool in understanding various fundamental fluid flow phenomena in engineering (mechanical, aeronautics, chemical, materials, civil, etc.) and science (astrophysics, geophysics, biophysics, etc.), and turbulence in particular. However, there are many discrepancies between classical hydrodynamic stability theory and experiments. In this thesis, the limitations of traditional hydrodynamic stability theory are shown and a framework for robust flow stability theory is formulated. A host of new techniques like gramians, singular values, operator norms, etc. are introduced to understand the role of various kinds of uncertainty. An interesting feature of this framework is the close interplay between theory and computations. It is shown that a subset of Navier-Stokes equations are globally, non-nonlinearly stable for all Reynolds number. Yet, invoking this new theory, it is shown that these equations produce structures (vortices and streaks) as seen in the experiments. The experiments are done in zero pressure gradient transiting boundary layer on a flat plate in free surface tunnel. Digital particle image velocimetry, and MEMS based laser Doppler velocimeter and shear stress sensors have been used to make quantitative measurements of the flow. Various theoretical and computational predictions are in excellent agreement with the experimental data. A closely related topic of modeling, simulation and complexity reduction of large mechanics problems with multiple spatial and temporal scales is also studied. A nice method that rigorously quantifies the important scales and automatically gives models of the problem to various levels of accuracy is introduced. Computations done using spectral methods are presented.

  11. CVB: the Constrained Vapor Bubble Capillary Experiment on the International Space Station MARANGONI FLOW REGION

    Science.gov (United States)

    Wayner, Peter C., Jr.; Kundan, Akshay; Plawsky, Joel

    2014-01-01

    The Constrained Vapor Bubble (CVB) is a wickless, grooved heat pipe and we report on a full- scale fluids experiment flown on the International Space Station (ISS). The CVB system consists of a relatively simple setup a quartz cuvette with sharp corners partially filled with either pentane or an ideal mixture of pentane and isohexane as the working fluids. Along with temperature and pressure measurements, the two-dimensional thickness profile of the menisci formed at the corners of the quartz cuvette was determined using the Light Microscopy Module (LMM). Even with the large, millimeter dimensions of the CVB, interfacial forces dominate in these exceedingly small Bond Number systems. The experiments were carried out at various power inputs. Although conceptually simple, the transport processes were found to be very complex with many different regions. At the heated end of the CVB, due to a high temperature gradient, we observed Marangoni flow at some power inputs. This region from the heated end to the central drop region is defined as a Marangoni dominated region. We present a simple analysis based on interfacial phenomena using only measurements from the ISS experiments that lead to a predictive equation for the thickness of the film near the heated end of the CVB. The average pressure gradient for flow in the film is assumed due to the measured capillary pressure at the two ends of the liquid film and that the pressure stress gradient due to cohesion self adjusts to a constant value over a distance L. The boundary conditions are the no slip condition at the wall interface and an interfacial shear stress at the liquid- vapor interface due to the Marangoni stress, which is due to the high temperature gradient. Although the heated end is extremely complex, since it includes three- dimensional variations in radiation, conduction, evaporation, condensation, fluid flow and interfacial forces, we find that using the above simplifying assumptions, a simple successful

  12. Localized reactive flow in carbonate rocks: Core-flood experiments and network simulations

    Science.gov (United States)

    Wang, Haoyue; Bernabé, Yves; Mok, Ulrich; Evans, Brian

    2016-11-01

    We conducted four core-flood experiments on samples of a micritic, reef limestone from Abu Dhabi under conditions of constant flow rate. The pore fluid was water in equilibrium with CO2, which, because of its lowered pH, is chemically reactive with the limestone. Flow rates were between 0.03 and 0.1 mL/min. The difference between up and downstream pore pressures dropped to final values ≪1 MPa over periods of 3-18 h. Scanning electron microscope and microtomography imaging of the starting material showed that the limestone is mostly calcite and lacks connected macroporosity and that the prevailing pores are few microns large. During each experiment, a wormhole formed by localized dissolution, an observation consistent with the decreases in pressure head between the up and downstream reservoirs. Moreover, we numerically modeled the changes in permeability during the experiments. We devised a network approach that separated the pore space into competing subnetworks of pipes. Thus, the problem was framed as a competition of flow of the reactive fluid among the adversary subnetworks. The precondition for localization within certain time is that the leading subnetwork rapidly becomes more transmissible than its competitors. This novel model successfully simulated features of the shape of the wormhole as it grew from few to about 100 µm, matched the pressure history patterns, and yielded the correct order of magnitude of the breakthrough time. Finally, we systematically studied the impact of changing the statistical parameters of the subnetworks. Larger mean radius and spatial correlation of the leading subnetwork led to faster localization.

  13. Experiments and Simulations of Fluid Flow in Heterogeneous Reservoir Models - Emphasis on Impacts from Crossbeds and Fractures

    Energy Technology Data Exchange (ETDEWEB)

    Boerresen, Knut Arne

    1996-12-31

    Hydrocarbon recovery from subsurface reservoirs has become increasingly dependent on advanced recovery techniques that require improved understanding of the physics of fluid flow within and across geological units including small-scale heterogeneities and fractures. In this thesis, impacts from heterogeneities on local fluid flow are studied experimentally by means of imaging techniques to visualize fluid flow in two dimensions during flooding of larger reservoir models. Part 1 reflects the multi-disciplinary collaboration, by briefly introducing the relevant geology, the literature on experiments on fluid flow in bedded structures, and outlining the applied numerical simulator and imaging techniques applied to visualize fluid flow. The second part contains a synopsis of displacement experiments in naturally laminated sandstones and in crossbed laboratory models, and of the impact from incipient shear fractures on oil recovery. The detailed results obtained from the experiments and simulations are described in six papers, all included. 215 refs., 108 figs., 16 tabs.

  14. Experiments and Simulations of Fluid Flow in Heterogeneous Reservoir Models - Emphasis on Impacts from Crossbeds and Fractures

    Energy Technology Data Exchange (ETDEWEB)

    Boerresen, Knut Arne

    1997-12-31

    Hydrocarbon recovery from subsurface reservoirs has become increasingly dependent on advanced recovery techniques that require improved understanding of the physics of fluid flow within and across geological units including small-scale heterogeneities and fractures. In this thesis, impacts from heterogeneities on local fluid flow are studied experimentally by means of imaging techniques to visualize fluid flow in two dimensions during flooding of larger reservoir models. Part 1 reflects the multi-disciplinary collaboration, by briefly introducing the relevant geology, the literature on experiments on fluid flow in bedded structures, and outlining the applied numerical simulator and imaging techniques applied to visualize fluid flow. The second part contains a synopsis of displacement experiments in naturally laminated sandstones and in crossbed laboratory models, and of the impact from incipient shear fractures on oil recovery. The detailed results obtained from the experiments and simulations are described in six papers, all included. 215 refs., 108 figs., 16 tabs.

  15. Permeable barrier materials for strontium immobilization: Unsaturated flow apparatus determination of hydraulic conductivity -- Column sorption experiments

    International Nuclear Information System (INIS)

    Moody, T.E.; Conca, J.

    1996-09-01

    Selected materials were tested to emulate a permeable barrier and to examine the (1) capture efficiency of these materials relating to the immobilization of strontium-90 and hexavalent chromium (Cr 6+ ) in Hanford Site groundwater; and (2) hydraulic conductivity of the barrier material relative to the surrounding area. The emplacement method investigated was a permeable reactive barrier to treat contaminated groundwater as it passes through the barrier. The hydraulic conductivity function was measured for each material, and retardation column experiments were performed for each material. Measurements determining the hydraulic conductivity at unsaturated through saturated water content were executed using the Unsaturated Flow Apparatus

  16. Linear Aerospike SR-71 Experiment (LASRE) dumps water after first in-flight cold flow test

    Science.gov (United States)

    1998-01-01

    The NASA SR-71A successfully completed its first cold flow flight as part of the NASA/Rocketdyne/Lockheed Martin Linear Aerospike SR-71 Experiment (LASRE) at NASA's Dryden Flight Research Center, Edwards, California on March 4, 1998. During a cold flow flight, gaseous helium and liquid nitrogen are cycled through the linear aerospike engine to check the engine's plumbing system for leaks and to check the engine operating characterisitics. Cold-flow tests must be accomplished successfully before firing the rocket engine experiment in flight. The SR-71 took off at 10:16 a.m. PST. The aircraft flew for one hour and fifty-seven minutes, reaching a maximum speed of Mach 1.58 before landing at Edwards at 12:13 p.m. PST. 'I think all in all we had a good mission today,' Dryden LASRE Project Manager Dave Lux said. Flight crew member Bob Meyer agreed, saying the crew 'thought it was a really good flight.' Dryden Research Pilot Ed Schneider piloted the SR-71 during the mission. Lockheed Martin LASRE Project Manager Carl Meade added, 'We are extremely pleased with today's results. This will help pave the way for the first in-flight engine data-collection flight of the LASRE.' The LASRE experiment was designed to provide in-flight data to help Lockheed Martin evaluate the aerodynamic characteristics and the handling of the SR-71 linear aerospike experiment configuration. The goal of the project was to provide in-flight data to help Lockheed Martin validate the computational predictive tools it was using to determine the aerodynamic performance of a future reusable launch vehicle. The joint NASA, Rocketdyne (now part of Boeing), and Lockheed Martin Linear Aerospike SR-71 Experiment (LASRE) completed seven initial research flights at Dryden Flight Research Center. Two initial flights were used to determine the aerodynamic characteristics of the LASRE apparatus (pod) on the back of the SR-71. Five later flights focused on the experiment itself. Two were used to cycle gaseous

  17. The effects of autonomy-supportive and controlling teaching behaviour in biology lessons with primary and secondary experiences on students' intrinsic motivation and flow-experience

    Science.gov (United States)

    Hofferber, Natalia; Basten, Melanie; Großmann, Nadine; Wilde, Matthias

    2016-09-01

    Self-Determination Theory and Flow Theory propose that perceived autonomy fosters the positive qualities of motivation and flow-experience. Autonomy-support can help to maintain students' motivation in very interesting learning activities and may lead to an increase in the positive qualities of motivation in less interesting learning activities. This paper investigates whether autonomy-supportive or controlling teaching behaviour influence students' motivation and flow-experience in biology class. In study 1, 158 students of grade six worked on the adaptations of Harvest Mice (Micromys minutus) with living animals. The 153 sixth graders of study 2 dealt with the same content but instead worked with short films on laptops. Previous studies have shown that students perceive film sequences as less interesting than working with living animals. Students' intrinsic motivation and flow-experience were measured at the end of the first and the third lesson. In study 1, autonomy-supportive teaching behaviour led to significant differences in students' intrinsic motivation and flow-experience when compared to controlling teaching behaviour. In study 2, motivation and flow-experience were not always in line with theory. The positive effects of autonomy-supportive and the non-beneficial effects of the controlling teaching behaviour seem to be dependent on the interestingness of the teaching material.

  18. Hydraulic experiment on flow and topography change in harbor due to tsunami and its numerical simulation

    International Nuclear Information System (INIS)

    Fujii, Naoki; Ikeno, Masaaki; Sakakiyama, Tsutomu; Matsuyama, Masafumi; Takao, Makoto; Mukohara, Takeshi

    2009-01-01

    Numerical model of topography change is important to examine collapse of the harbor facilities by sand transport due to tsunami. Problems for evaluation of sand transport due to tsunami with topography change model are in precision of the numerical model and topography change data. Therefore, we installed the harbor in large-scaled wave tank and carried out experiment about tsunami flow and topography change to get those detailed data. For results provided by experimental test, we applied the topography change model of Ikeno et al. (2009a) and evaluated it about the reproduction characteristics. As a result, it was confirmed that reproduction of an experiment improved by using new pickup rate formula proposed by Ikeno et al. (2009a). (author)

  19. Flow-induced and acoustically induced vibration experience in operating gas-cooled reactors

    International Nuclear Information System (INIS)

    Halvers, L.J.

    1977-03-01

    An overview has been presented of flow-induced and acoustically induced vibration failures that occurred in the past in gas-cooled graphite-moderated reactors, and the importance of this experience for the Gas-Cooled Fast-Breeder Reactor (GCFR) project has been assessed. Until now only failures in CO 2 -cooled reactors have been found. No problems with helium-cooled reactors have been encountered so far. It is shown that most of the failures occurred because flow-induced and acoustically induced dynamic loads were underestimated, while at the same time not enough was known about the influence of environmental parameters on material behavior. All problems encountered were solved. The comparison of the influence of the gas properties on acoustically induced and flow-induced vibration phenomena shows that the interaction between reactor design and the thermodynamic properties of the primary coolant precludes a general preference for either carbon dioxide or helium. The acoustic characteristics of CO 2 and He systems are different, but the difference in dynamic loadings due to the use of one rather than the other remains difficult to predict. A slight preference for helium seems, however, to be justified

  20. The Experience at Russian Nuclear Sites of Modeling Groundwater Flow on Different Scales

    Science.gov (United States)

    Zinin, A.; Zinina, G.; Samsanova, L.; Vasilkova, N.; Alexandrova, L.; Drozhko, E.

    2001-12-01

    The experience of developing models of different scales to predict contaminant plume migration in ground waters is analyzed. The method of developing a three-dimensional transient model is demonstrated to estimate high-density solutions migrating from the surface storage of liquid radioactive waste, using a two-dimensional regional model for setting boundary conditions (Lake Karachay, PA "Mayak", Russia). The model is used to calculate three-dimensional transient distribution of pressure, density and concentrations of the dissolved admixtures in the non-confined aquifers. Interpolation is also specified to calculate boundary conditions parameters of the inserted models. The method of constructing a local filtration model is described to predict the contaminant plume spreading from the operating ground of deep burial of liquid radioactive wastes (The Siberian Chemical Plant, Seversk). The local model uses smaller grid gaps over time and space and a more detailed stratiographic division of the section as compared to the regional model intended to be used for estimating groundwater resourses. The flow distribution within the local model boundaries is described as the products of an average annual flow and periodical time function (function of monthly fluctuations) and the function of spatial variables. The parameters of the distribution function, represented on the local model grid by the values, were determined by solving the inverse problem. The sensivity analysis of the target function of the inverse problem to the small variations of the average annual flows is described.

  1. Challenges in modeling unstable two-phase flow experiments in porous micromodels

    Science.gov (United States)

    Meheust, Y.; Ferrari, A.; Jimenez-Martinez, J.; Le Borgne, T.; Lunati, I.

    2014-12-01

    The simulation of unstable invasion patterns in porous media flow is challenging since small perturbations tend to grow in time, so that slight differences in geometry or initial conditions potentially give rise to significantly different solutions. Here we present a detailed comparison of pore scale simulations and experiments of unstable primary drainage in porous micromodels. The porous medium consists of a Hele-Shaw cell containing cylindrical obstacles. Two experimental flow cells have been constructed by soft lithography, with different degrees of heterogeneity in the grain size distribution. To model two-phase flow at the pore scale, we solve Navier-Stokes equations for mass and momentum conservation in the discretized pore space and employ the Volume of Fluid (VOF) method to track the evolution of the interface. During drainage, if the defending fluid is the most viscous, viscous forces destabilize the interface, giving rise to the formation of preferential flow paths, in the form of a branched fingering structure. We test different numerical models (a 2D vertical integrated model and a full 3D model) and different initial conditions, studying their impact on the simulated spatial distributions of the fluid phases. Although due to the unstable nature of the invasion, small discrepancies between the experimental setup and the numerical model can result in different fluids patterns (see figure), simulations show a satisfactory agreement with the structures observed experimentally. To estimate the ability of the numerical approach to reproduce unstable displacement, we compare several quantities in both the statistical and deterministic sense. We demonstrate the impact of three main sources of uncertainty : i) the uncertainty on the pore space geometry, ii) the interface initialization and ii) three dimensional effects [1]. Simulations in weakly heterogeneous geometries are found to be more challenging because uncertainties on pore neck widths are on the same

  2. Numerical Simulations of Counter Current Flow Experiments Using a Morphology Detection Algorithm

    Directory of Open Access Journals (Sweden)

    Thomas Höhne

    2012-09-01

    Full Text Available In order to improve the understanding of counter-current two-phase flows and to validate new physical models, CFD simulations of 1/3rd scale model of the hot leg of a German Konvoi PWR with rectangular cross section was performed. Selected counter-current flow limitation (CCFL experiments at the Helmholtz-Zentrum Dresden-Rossendorf (HZDR were calculated with ANSYS CFX 12.1 using the multi-fluid Euler-Euler modeling approach. The transient calculations were carried out using a gas/liquid inhomogeneous multiphase flow model coupled with a SST turbulence model for each phase. In the simulation, the surface drag was approached by a new correlation inside the Algebraic Interfacial Area Density (AIAD model. The AIAD model allows the detection of the morphological form of the two phase flow and the corresponding switching via a blending function of each correlation from one object pair to another. As a result this model can distinguish between bubbles, droplets and the free surface using the local liquid phase volume fraction value. A comparison with the high-speed video observations shows a good qualitative agreement. The results indicated that quantitative agreement of the CCFL characteristics between calculation and experimental data was obtained. To validate the model and to study scaling effects CFD simulations of the CCFL phenomenon in a full scale PWR hot leg of the UPTF test facility were performed. Also these results indicated a good agreement between the calculation and experimental data. The final goal is to provide an easy usable AIAD framework for all ANSYS CFX users, with the possibility of the implementation of their own correlations.

  3. Long-term animal experiments with an intraventricular axial flow blood pump.

    Science.gov (United States)

    Yamazaki, K; Kormos, R L; Litwak, P; Tagusari, O; Mori, T; Antaki, J F; Kameneva, M; Watach, M; Gordon, L; Mukuo, H; Umezu, M; Tomioka, J; Outa, E; Griffith, B P; Koyanagai, H

    1997-01-01

    A miniature intraventricular axial flow blood pump (IVAP) is undergoing in vivo evaluation in calves. The IVAP system consists of a miniature (phi 13.9 mm) axial flow pump that resides within the left ventricular (LV) chamber and a brushless DC motor. The pump is fabricated from titanium alloy, and the pump weight is 170 g. It produces a flow rate of over 5 L/min against 100 mmHg pressure at 9,000 rpm with an 8 W total power consumption. The maximum total efficiency exceeds 17%. A purged lip seal system is used in prototype no. 8, and a newly developed "Cool-Seal" (a low temperature mechanical seal) is used in prototype no. 9. In the Cool-Seal system, a large amount of purge flow is introduced behind the seal faces to augment convective heat transfer, keeping the seal face temperature at a low level for prevention of heat denaturation of blood proteins. The Cool-Seal system consumes < 10 cc purge fluid per day and has greatly extended seal life. The pumps were implanted in three calves (26, 30, and 168 days of support). The pump was inserted through a left thoracotomy at the fifth intercostal space. Two pursestring sutures were placed on the LV apex, and the apex was cored with a myocardial punch. The pump was inserted into the LV with the outlet cannula smoothly passing through the aortic valve without any difficulty. Only 5 min elapsed between the time of chest opening and initiation of pumping. Pump function remained stable throughout in all experiments. No cardiac arrhythmias were detected, even at treadmill exercise tests. The plasma free hemoglobin level remained in the acceptable range. Post mortem examination did not reveal any interference between the pump and the mitral apparatus. No major thromboembolism was detected in the vital organs in Cases 1 or 2, but a few small renal infarcts were detected in Case 3.

  4. Relationship between Long Working Hours and Suicidal Thoughts: Nationwide Data from the 4th and 5th Korean National Health and Nutrition Examination Survey.

    Science.gov (United States)

    Yoon, Jin-Ha; Jung, Pil Kyun; Roh, Jaehoon; Seok, Hongdeok; Won, Jong-Uk

    2015-01-01

    Long working hours are a worldwide problem and may increase the risk of various health issues. However, the health effects of long working hours on suicidal thoughts have not been frequently studied. Our goal was to investigate the relationship between long working hours and suicidal thoughts in the rapidly developing country of Korea. Data from 12,076 participants (7,164 men, 4,912 women) from the 4th and 5th Korean National Health and Nutrition Examination Surveys were used for the current analysis. Multivariate logistic regression models were used to estimate odds ratios and 95% confidence intervals for suicidal thoughts. Combined effects of long working hours and lower socioeconomic status or sleep disturbance were also estimated. Compared to groups who worked less than 52 hours per week, odds ratios (95% confidence intervals) for suicidal thoughts in groups who worked 60 hours or more per week were 1.36 (1.09-1.70) for males and 1.38 (1.11-1.72) for females, even after controlling for household income, marital status, history of hypertension or diabetes mellitus, health-related behaviors, and past two weeks' experience of injury, intoxication, or acute or chronic diseases, as well as type of work. The combined effects of long working hours with lower socioeconomic status, or with sleep disturbance, were also significantly higher compared to participants who worked less than 52 hours per week with higher socioeconomic status, or with 6-8 hours of nighttime sleep. In this study, long working hours were linked to suicidal thoughts for both genders. Additionally, the odds of those suicidal thoughts were higher for lower socioeconomic groups. To prevent adverse psychological health problems such as suicidal thoughts, a strategy regarding long working hours should be investigated.

  5. Relationship between Long Working Hours and Suicidal Thoughts: Nationwide Data from the 4th and 5th Korean National Health and Nutrition Examination Survey.

    Directory of Open Access Journals (Sweden)

    Jin-Ha Yoon

    Full Text Available Long working hours are a worldwide problem and may increase the risk of various health issues. However, the health effects of long working hours on suicidal thoughts have not been frequently studied. Our goal was to investigate the relationship between long working hours and suicidal thoughts in the rapidly developing country of Korea.Data from 12,076 participants (7,164 men, 4,912 women from the 4th and 5th Korean National Health and Nutrition Examination Surveys were used for the current analysis. Multivariate logistic regression models were used to estimate odds ratios and 95% confidence intervals for suicidal thoughts. Combined effects of long working hours and lower socioeconomic status or sleep disturbance were also estimated.Compared to groups who worked less than 52 hours per week, odds ratios (95% confidence intervals for suicidal thoughts in groups who worked 60 hours or more per week were 1.36 (1.09-1.70 for males and 1.38 (1.11-1.72 for females, even after controlling for household income, marital status, history of hypertension or diabetes mellitus, health-related behaviors, and past two weeks' experience of injury, intoxication, or acute or chronic diseases, as well as type of work. The combined effects of long working hours with lower socioeconomic status, or with sleep disturbance, were also significantly higher compared to participants who worked less than 52 hours per week with higher socioeconomic status, or with 6-8 hours of nighttime sleep.In this study, long working hours were linked to suicidal thoughts for both genders. Additionally, the odds of those suicidal thoughts were higher for lower socioeconomic groups. To prevent adverse psychological health problems such as suicidal thoughts, a strategy regarding long working hours should be investigated.

  6. Electrochemical reactions of the Th4+/Th couple on the tungsten, aluminum and bismuth electrodes in chloride molten salt

    International Nuclear Information System (INIS)

    Liu, Kui; Yuan, Li-Yong; Liu, Ya-Lan; Zhao, Xiu-Liang; He, Hui; Ye, Guo-An; Chai, Zhi-Fang; Shi, Wei-Qun

    2014-01-01

    This work concerns the electrochemical behaviors of Th 4+ on the tungsten, aluminum and bismuth electrodes in the LiCl-KCl eutectic, respectively, at 773 K. Cyclic voltammetry and square wave voltammetry were employed to investigate the cathodic reduction of Th 4+ . The results demonstrate that the reduction of Th 4+ is a one step process with a transfer of 4 electrons. The reversibility of the Th 4+ /Th couple on the bismuth film and tungsten electrodes is directly confirmed by the CV. The diffusion coefficient is also calculated to be (2.23 ± 0.16) × 10 −5 and (7.19 ± 0.12) × 10 −5 cm 2 /s by applying both cyclic voltammetry and chronopotentiometry, respectively. A series of redox couples were confirmed to be associated with the formation of different kinds of Al-Th intermetallic compounds. Compared to Al electrode, a cathodic shift of the reduction potential of the Th 4+ is observed on the Al film electrode which is not conducive for the potentiostatic extraction of thorium. The cathodic depolarization gives a shift of 420 mV on the Al electrode, while 490 mV on the Bi film electrode for the reduction of Th 4+ compared to the inert W electrode. The reduction potential of Th 4+ on the Bi film electrode is 70 mV more anodic than that on the Al electrode. Potentiostatic electrolyses were carried out on an Al plate and Bi liquid electrode to confirm the formation of the Th alloys. Two Al-Th alloys (Al 3 Th and Al 2 Th) and one Bi-Th alloy (Bi 2 Th) were obtained, respectively

  7. Reactive flow modeling of small scale detonation failure experiments for a baseline non-ideal explosive

    Energy Technology Data Exchange (ETDEWEB)

    Kittell, David E.; Cummock, Nick R.; Son, Steven F. [School of Mechanical Engineering, Purdue University, West Lafayette, Indiana 47907 (United States)

    2016-08-14

    Small scale characterization experiments using only 1–5 g of a baseline ammonium nitrate plus fuel oil (ANFO) explosive are discussed and simulated using an ignition and growth reactive flow model. There exists a strong need for the small scale characterization of non-ideal explosives in order to adequately survey the wide parameter space in sample composition, density, and microstructure of these materials. However, it is largely unknown in the scientific community whether any useful or meaningful result may be obtained from detonation failure, and whether a minimum sample size or level of confinement exists for the experiments. In this work, it is shown that the parameters of an ignition and growth rate law may be calibrated using the small scale data, which is obtained from a 35 GHz microwave interferometer. Calibration is feasible when the samples are heavily confined and overdriven; this conclusion is supported with detailed simulation output, including pressure and reaction contours inside the ANFO samples. The resulting shock wave velocity is most likely a combined chemical-mechanical response, and simulations of these experiments require an accurate unreacted equation of state (EOS) in addition to the calibrated reaction rate. Other experiments are proposed to gain further insight into the detonation failure data, as well as to help discriminate between the role of the EOS and reaction rate in predicting the measured outcome.

  8. Experiment study on sediment erosion of Pelton turbine flow passage component material

    Science.gov (United States)

    Liu, J.; Lu, L.; Zhu, L.

    2012-11-01

    A rotating and jet experiment system with high flow velocity is designed to study the anti-erosion performance of materials. The resultant velocity of the experiment system is high to 120 m/s. The anti-erosion performance of materials used in needle and nozzle and bucket of Pelton turbine, which is widely used in power station with high head and little discharge, was studied in detail by this experiment system. The experimental studies were carried with different resultant velocities and sediment concentrations. Multiple linear regression analysis method was applied to get the exponents of velocity and sediment concentration. The exponents for different materials are different. The exponents of velocity ranged from 3 to 3.5 for three kinds of material. And the exponents of sediment concentration ranged from 0.97 to 1.03 in this experiment. The SEM analysis on the erosion surface of different materials was also carried. On the erosion condition with high resultant impact velocity, the selective cutting loss of material is the mainly erosion mechanism for metal material.

  9. Experiment study on sediment erosion of Pelton turbine flow passage component material

    International Nuclear Information System (INIS)

    Liu, J; Lu, L; Zhu, L

    2012-01-01

    A rotating and jet experiment system with high flow velocity is designed to study the anti-erosion performance of materials. The resultant velocity of the experiment system is high to 120 m/s. The anti-erosion performance of materials used in needle and nozzle and bucket of Pelton turbine, which is widely used in power station with high head and little discharge, was studied in detail by this experiment system. The experimental studies were carried with different resultant velocities and sediment concentrations. Multiple linear regression analysis method was applied to get the exponents of velocity and sediment concentration. The exponents for different materials are different. The exponents of velocity ranged from 3 to 3.5 for three kinds of material. And the exponents of sediment concentration ranged from 0.97 to 1.03 in this experiment. The SEM analysis on the erosion surface of different materials was also carried. On the erosion condition with high resultant impact velocity, the selective cutting loss of material is the mainly erosion mechanism for metal material.

  10. Investigation of mixing enhancement in porous media under helical flow conditions: 3-D bench-scale experiments

    DEFF Research Database (Denmark)

    Chiogna, Gabriele; Ye, Yu; Cirpka, Olaf A.

    2017-01-01

    us to quantify spreading and dilution of the solute plumes at the outlet cross section. Moreover, we collected direct evidence of plume spiraling and visual proof of helical flow by freezing and slicing the porous medium at different cross sections and observing the dye-tracer distribution. Model...... performed steady-state conservative tracer experiments in a fully three-dimensional flow-through chamber to investigate the effects of helical flow on plume spiraling and deformation, as well as on its dilution [4]. Helical flow was created by packing the porous medium in angled stripes of materials...

  11. The Relationship Between Personality Traits, Flow-Experience, and Different Aspects of Practice Behavior of Amateur Vocal Students

    Science.gov (United States)

    Heller, Katharina; Bullerjahn, Claudia; von Georgi, Richard

    2015-01-01

    Most of the existing studies on musical practice are concerned with instrumentalists only. Since singers are seldom considered in research, the present study is based on an online-sample of amateur vocal students (N = 120; 92 female, 28 male). The study investigated the correlations between personality traits, flow-experience and several aspects of practice characteristics. Personality was represented by the three personality dimensions extraversion, neuroticism and psychoticism, assessed by Eysenck’s Personality Profiler as well as the trait form of the Positive and Negative Affect Schedule. ‘Flow-experience,’ ‘self-congruence’ and ‘fear of losing control over concentration,’ assessed by the Practice Flow Inventory, served as variables for flow-experience. The practice motivation was measured by the Practice Motivation Questionnaire in four categories (‘self,’ ‘group,’ ‘audience,’ ‘teacher’). In addition, the Practice Behavior Questionnaire was used to provide an insight into the practice situation and behavior of singing students. The results show significant correlations: participants with high extraversion-scores experience significantly more flow than less extraverted persons, whereas lesser flow-experience seems to be related to high neuroticism-scores. Nevertheless, there is no influence in flow-experience concerning singing style (‘classical’ or ‘popular’). The longer the practicing time, the more likely students are to achieve flow-experience. However, older singers tend to have less flow-experience. Consequently, singers seem to differ in their personality and practice behavior compared to other musicians. Most of the findings show that having control over one’s instrument is decisive for achieving a performance of high quality, especially for singers. On the other hand, certainty in handling an instrument is essential to arouse a flow-feeling. However, flow-experience seems to be common mainly with amateur singers

  12. Improved Reactive Flow Modeling of the LX-17 Double Shock Experiments

    Science.gov (United States)

    Rehagen, Thomas J.; Vitello, Peter

    2017-06-01

    Over driven double shock experiments provide a measurement of the properties of the reaction product states of the insensitive high explosive LX-17 (92.5% TATB and 7.5% Kel-F by weight). These experiments used two flyer materials mounted on the end of a projectile to send an initial shock through the LX-17, followed by a second shock of a higher magnitude into the detonation products. In the experiments, the explosive was initially driven by the flyer plate to pressures above the Chapman-Jouguet state. The particle velocity history was recorded by Photonic Doppler Velocimetry (PDV) probes pointing at an aluminum foil coated LiF window. The PDV data shows a sharp initial shock and decay, followed by a rounded second shock. Here, the experimental results are compared to 2D and 3D Cheetah reactive flow modeling. Our default Cheetah reactive flow model fails to accurately reproduce the decay of the first shock or the curvature or strength of the second shock. A new model is proposed in which the carbon condensate produced in the reaction zone is controlled by a kinetic rate. This allows the carbon condensate to be initially out of chemical equilibrium with the product gas. This new model reproduces the initial detonation peak and decay, and matches the curvature of the second shock, however, it still over-predicts the strength of the second shock. This work was performed under the auspices of the U.S. Department of Energy by Lawrence Livermore National Laboratory under Contract No. DE-AC52-07NA27344.

  13. Experiment of flow regime map and local condensing heat transfer coefficients inside three dimensional inner microfin tubes

    Science.gov (United States)

    Du, Yang; Xin, Ming Dao

    1999-03-01

    This paper developed a new type of three dimensional inner microfin tube. The experimental results of the flow patterns for the horizontal condensation inside these tubes are reported in the paper. The flow patterns for the horizontal condensation inside the new made tubes are divided into annular flow, stratified flow and intermittent flow within the test conditions. The experiments of the local heat transfer coefficients for the different flow patterns have been systematically carried out. The experiments of the local heat transfer coefficients changing with the vapor dryness fraction have also been carried out. As compared with the heat transfer coefficients of the two dimensional inner microfin tubes, those of the three dimensional inner microfin tubes increase 47-127% for the annular flow region, 38-183% for the stratified flow and 15-75% for the intermittent flow, respectively. The enhancement factor of the local heat transfer coefficients is from 1.8-6.9 for the vapor dryness fraction from 0.05 to 1.

  14. Analysis of material flow in metal forming processes by using computer simulation and experiment with model material

    International Nuclear Information System (INIS)

    Kim, Heon Young; Kim, Dong Won

    1993-01-01

    The objective of the present study is to analyze material flow in the metal forming processes by using computer simulation and experiment with model material, plasticine. A UBET program is developed to analyze the bulk flow behaviour of various metal forming problems. The elemental strain-hardening effect is considered in an incremental manner and the element system is automatically regenerated at every deforming step in the program. The material flow behaviour in closed-die forging process with rib-web type cavity are analyzed by UBET and elastic-plastic finite element method, and verified by experiments with plasticine. There were good agreements between simulation and experiment. The effect of corner rounding on material flow behavior is investigated in the analysis of backward extrusion with square die. Flat punch indentation process is simulated by UBET, and the results are compared with that of elastic-plastic finite element method. (Author)

  15. The Effect of the Conceptual Change Oriented Instruction through Cooperative Learning on 4th Grade Students' Understanding of Earth and Sky Concepts

    Science.gov (United States)

    Celikten, Oksan; Ipekcioglu, Sevgi; Ertepinar, Hamide; Geban, Omer

    2012-01-01

    The purpose of this study was to compare the effectiveness of the conceptual change oriented instruction through cooperative learning (CCICL) and traditional science instruction (TI) on 4th grade students' understanding of earth and sky concepts and their attitudes toward earth and sky concepts. In this study, 56 fourth grade students from the…

  16. The Relationship of Values in Elementary School 4th Grade Social Studies Textbook with the Attainments and Their Level of Being Included in Student Workbooks

    Science.gov (United States)

    Kilic, Abdurrahman

    2012-01-01

    In this study, the relationship of values in elementary school 4th grade Social Studies textbook with the attainments and their level of being included in student workbook are tried to be determined. Case study, which is a qualitative research method, was applied for this research. To collect data, document analysis technique, which is among the…

  17. Review of Handbook of Autopsy Practice, Brenda L. Waters (Ed.). 4th edition, Humana Press (2009). ISBN: 978-1-58829-841-6

    DEFF Research Database (Denmark)

    Leth, Peter Mygind

    2010-01-01

    This 4th edition of Handbook of Autopsy Practice is a thoroughly updated version. Autopsy practice has undergone significant changes in recent time due to technological advancements such as molecular diagnostics, immunohistochemisty and the introduction of post-mortem imaging techniques. In the s...

  18. Coefficients of Correlation of IQ's on the WAIS-R with Standard Age Scores on the Stanford-Binet, 4th Edition for Previously Identified Mentally Handicapped Adolescents.

    Science.gov (United States)

    Richardson, John C.

    This paper presents a study regarding the correlation of the Stanford-Binet: 4th Edition Intelligence Quotient (IQ) scores with the Wechsler Adult Intelligence Scale-Revised (WAIS-R) IQ scores for the purpose of improving the identification process for educable mentally handicapped (EMH) school age adolescents and young adults. The sample included…

  19. New technological developments provide deep-sea sediment density flow insights: the Monterey Coordinated Canyon Experiment

    Science.gov (United States)

    O'Reilly, T. C.; Kieft, B.; Chaffey, M. R.; Wolfson-Schwehr, M.; Herlien, R.; Bird, L.; Klimov, D.; Paull, C. K.; Gwiazda, R.; Lundsten, E. M.; Anderson, K.; Caress, D. W.; Sumner, E. J.; Simmons, S.; Parsons, D. R.; Talling, P.; Rosenberger, K. J.; Xu, J.; Maier, K. L.; Gales, J. A.

    2017-12-01

    The Monterey Coordinated Canyon Experiment (CCE) deployed an array of instruments along the Monterey Canyon floor to characterize the structure, velocity and frequency of sediment flows. CCE utilized novel technologies developed at MBARI to capture sediment flow data in unprecedented detail. 1. The Seafloor Instrument Node (SIN) at 1850 meters depth housed 3 ADCPs at 3 different frequencies, CTD, current meter, oxygen optode, fluorometer/backscatter sensor, and logged data at 10 second intervals or faster. The SIN included an acoustic modem for communication with shore through a Wave Glider relay, and provided high-resolution measurements of three flow events during three successive deployments over 1.5 years. 2. Beachball-sized Benthic Event Detectors (BEDs) were deployed on or under the seafloor to measure the characteristics of sediment density flows. Each BED recorded data from a pressure sensor and a 3-axis accelerometer and gyro to characterize motions during transport events (e.g. tumble vs rotation). An acoustic modem capable of operating through more than a meter of sediment enabled communications with a ship or autonomous surface vehicle. Multiple BEDs were deployed at various depths in the canyon during CCE, detecting and measuring many transport events; one BED moved 9 km down canyon in 50 minutes during one event. 3. Wave Glider Hot Spot (HS), equipped with acoustic and RF modems, acted as data relay between SIN, BEDs and shore, and acoustically located BEDs after sediment density flows.. In some cases HS relayed BED motion data to shore within a few hours of the event. HS provided an acoustic console to the SIN, allowing shore-based users to check SIN health and status, perform maintenance, etc. 4. Mapping operations were conducted 4 times at the SIN site to quantify depositional and erosional patterns, utilizing a prototype ultra-high-resolution mapping system on the ROV Doc Ricketts. The system consists of a 400-kHz Reson 7125 multibeam sonar, a 3

  20. Histopathology Image Analysis in Two Long-Term Animal Experiments with Helical Flow Total Artificial Heart.

    Science.gov (United States)

    Wotke, Jiri; Homolka, Pavel; Vasku, Jaromír; Dobsak, Petr; Palanova, Petra; Mrkvicova, Veronika; Konecny, Petr; Soska, Vladimir; Pohanka, Michal; Novakova, Marie; Yurimoto, Terumi; Saito, Itsuro; Inoue, Yusuke; Isoyama, Takashi; Abe, Yusuke

    2016-12-01

    Histopathological analysis can provide important information in long-term experiments with total artificial heart (TAH). Recently, a new type of blood pump, the helical flow total artificial heart (HF-TAH) was developed. This study aimed to investigate the changes in selected vital organs in animal experiments with implanted HF-TAH. Samples from lung, liver, and kidneys from two female goats (No. 1301 and No. 1304) with implanted HF-TAH were analyzed. Tissue samples were fixed in 10% formaldehyde and 4 µm thick transverse sections were stained with hematoxylin-eosin (HE). Additional staining was done for detection of connective tissue (Masson-Goldner stain) and for detection of iron (hemosiderin) deposits (Perls stain). Sections were scanned at 100× and 500× magnification with a light microscope. Experiment no. 1301 survived 100 days (cause of termination was heavy damage of the right pump); experimental goat no.1304 survived 68 days and was sacrificed due to severe right hydrodynamic bearing malfunction. Histopathological analysis of liver samples proved signs of chronic venostasis with limited focal necrotic zones. Dilated tubules, proteinaceous material in tubular lumen, and hemosiderin deposits were detected in kidney samples. Contamination of the organs by embolized micro-particles was suspected at the autopsy after discovery of visible damage (scratches) of the pump impeller surface (made from titanium alloy) in both experiments. Sporadic deposits of foreign micro-particles (presumably titanium) were observed in most of the analyzed parenchymal organs. However, the described deposits were not in direct connection with inflammatory reactions in the analyzed tissues. Histopathological analysis showed the presence of minimal contamination of the lung, kidney, and liver tissue samples by foreign material (titanium very likely). The analysis showed only limited pathological changes, especially in liver and kidneys, which might be attributed to the influence of

  1. Numerical study of SNCR application to a full-scale stoker incinerator at Daejon 4th industrial complex

    International Nuclear Information System (INIS)

    Hey-Suk Kim; Mi-Soo Shin; Dong-Soon Jang; Tae-In Ohm

    2004-01-01

    Considering the rapid variation of waste composition and the more severe regulation trend of pollutant emission in this country, the importance of the development of a reliable computer program for a full-scale, stoker-type incinerator cannot be emphasized too much, especially in the view of proper design and optimal determination of operating condition of existing and future constructed facility. To this end, a comprehensive, numerical model related with the process of the waste-off gaseous combustion with the capacity of 200 tons/day is successfully made. This includes development of several phenomenological models such as municipal waste-off gaseous reaction, NO pollutant generation and destruction in turbulence-related environment. Especially in this study a number of sound assumptions have been made for the NO reaction model, 3-D geometry of incinerator and waste-bed model to achieve the efficient incorporation of the empirical models and enhancement of the stability of calculation process. First of all, the turbulence-related, complex combustion chemistry involved with NO reaction is modeled by the harmonic mean method, which is given by the relative strength of the rates of chemistry and turbulent mixing. Further, the 3-D rectangular shape of the incinerator is simply approximated by a 3-D axi-symmetric geometry with equivalent area. And the modeling of complex waste-burning process on moving grate is described by a pure gaseous combustion process of waste off-gas. The program developed in this study is successfully validated by comparing with the experimental data such as temperature and NO concentration profiles in the incinerator located at 4th industrial complex of Daejon, S. Korea. Using the program developed, a series of parametric investigations have been made for the evaluation of SNCR process and thereby evaluate various important design and the operating variables. The major parameters considered in this parametric study are heating value of

  2. Proposal to support the 4th international conference on nitrification and related processes (ICoN4)

    International Nuclear Information System (INIS)

    Klotz, Martin Gunter

    2016-01-01

    The 4th International Conference on Nitrification and Related Processes (ICoN4) commencing between June 27 and July 1, 2015, at the University of Alberta in Edmonton, Alberta, Canada brings together an international collection of academic, government, and private sector researchers of the global biogeochemical nitrogen cycle to share their scientific discoveries, innovations and pertinent societal impacts. The classical understanding of “nitrification” describes the two-step transformation of ammonium to nitrite and nitrite to nitrate; however, we now know from the analysis genome sequences, the application of ‘omics technologies, microbial ecology, biogeochemistry, and microbial physiology that the transformation of ammonium is not performed by a few particular groups of microorganisms nor is it confined to oxic environments. Past ICoN meetings have explored the interconnections between ammonium- and nitrite-consuming processes in all ecosystems, the emission of greenhouse gases by these processes and their control, and the intersection between intermediates of the nitrification process and other elemental cycles; this has generated tremendous progress in our understanding of the global nitrogen cycle and it has generated excitement in the next generation of N cycle researchers. Nitrification research has a long-standing connection to the Community Science Program of the DOE. Between 1999 and 2001, the JGI generated the first genome sequence of an ammonia-oxidizing bacterium, Nitrosomonas europaea ATCC 19718, and it has subsequently sequenced, or is in the process of sequencing over 50 additional genomes from ammonia-oxidizing bacteria, nitrite-oxidizing bacteria, and ammonia-oxidizing archaea. Autotrophic ammonia- and nitrite-transforming microorganisms play also a critical role in carbon cycling and sequestration in nearly all ecosystems. Not only do they control the concentration and speciation of biologically available N to plants and other

  3. Proposal to support the 4th international conference on nitrification and related processes (ICoN4)

    Energy Technology Data Exchange (ETDEWEB)

    Klotz, Martin Gunter [Univ. of North Carolina, Charlotte, NC (United States)

    2016-11-04

    The 4th International Conference on Nitrification and Related Processes (ICoN4) commencing between June 27 and July 1, 2015, at the University of Alberta in Edmonton, Alberta, Canada brings together an international collection of academic, government, and private sector researchers of the global biogeochemical nitrogen cycle to share their scientific discoveries, innovations and pertinent societal impacts. The classical understanding of “nitrification” describes the two-step transformation of ammonium to nitrite and nitrite to nitrate; however, we now know from the analysis genome sequences, the application of ‘omics technologies, microbial ecology, biogeochemistry, and microbial physiology that the transformation of ammonium is not performed by a few particular groups of microorganisms nor is it confined to oxic environments. Past ICoN meetings have explored the interconnections between ammonium- and nitrite-consuming processes in all ecosystems, the emission of greenhouse gases by these processes and their control, and the intersection between intermediates of the nitrification process and other elemental cycles; this has generated tremendous progress in our understanding of the global nitrogen cycle and it has generated excitement in the next generation of N cycle researchers. Nitrification research has a long-standing connection to the Community Science Program of the DOE. Between 1999 and 2001, the JGI generated the first genome sequence of an ammonia-oxidizing bacterium, Nitrosomonas europaea ATCC 19718, and it has subsequently sequenced, or is in the process of sequencing over 50 additional genomes from ammonia-oxidizing bacteria, nitrite-oxidizing bacteria, and ammonia-oxidizing archaea. Autotrophic ammonia- and nitrite-transforming microorganisms play also a critical role in carbon cycling and sequestration in nearly all ecosystems. Not only do they control the concentration and speciation of biologically available N to plants and other

  4. Analysis of body composition of the abdomen at the level of the 4th lumbar vertebral body by CT

    International Nuclear Information System (INIS)

    Kikuchi, Tetsujiro

    1988-01-01

    Body composition of the area at the level of the 4th lumbar vertebral section was studied on X-ray CT images in 62 normal volunteers (32 men and 30 women ), whose ages ranged from 20 and 79 years. The total cross-sectional area was smallest in persons in their twenties, irrespecstive of sex, and began to increase after the age of 30. The abdominal cavity and muscles had the highest cross-sectional ratio (34%) to the total body, followed by subcutaneous fat in men. In women, the subcutaneous fat and abdominal cavity had a ratio of 34% to the total body. According to age groups, men in their twenties and thirties had the highest ratio of the muscle to the total body, followed by that of abdominal cavity and subcutaneous fat. In the group older than 40, the ratio of organs to the total body was as follows: the abdominal cavity>muscle>subcutaneous fat. Since the age of 70, each ratio of the muscle or subcutaneous fat to the total body was the same. Women between their twenties and fifties had the highest ratio of subcutaneous fat to the total body. Since the age of 60, the ratio of the abdominal cavity became highest. The subcutaneous fat and abdominal cavity tended to increase with aging; and the muscles tended to decrease. The real area of the vertebra increased slightly, but the vertebral foramen tended to decrease with aging. In men, mean areas of the muscles were as follows: abdominis lateralis>erector spinae>psoas major>quadratus lumborum and transversospinalis>rectus abdominis muscle. The same tendency was observed for women, except for the quadratus lumborum and rectus abdominis muscle. According to Rohrer index, the real areas of all components except the vertebral foramen tended to increase in the order of types A, C, and D in men. In women, the real area of the subcutaneous fat increased as well in the order of types A, C, and D. (Namekawa, K)

  5. PREFACE: 9th World Congress on Computational Mechanics and 4th Asian Pacific Congress on Computational Mechanics

    Science.gov (United States)

    Khalili, N.; Valliappan, S.; Li, Q.; Russell, A.

    2010-07-01

    The use for mathematical models of natural phenomena has underpinned science and engineering for centuries, but until the advent of modern computers and computational methods, the full utility of most of these models remained outside the reach of the engineering communities. Since World War II, advances in computational methods have transformed the way engineering and science is undertaken throughout the world. Today, theories of mechanics of solids and fluids, electromagnetism, heat transfer, plasma physics, and other scientific disciplines are implemented through computational methods in engineering analysis, design, manufacturing, and in studying broad classes of physical phenomena. The discipline concerned with the application of computational methods is now a key area of research, education, and application throughout the world. In the early 1980's, the International Association for Computational Mechanics (IACM) was founded to promote activities related to computational mechanics and has made impressive progress. The most important scientific event of IACM is the World Congress on Computational Mechanics. The first was held in Austin (USA) in 1986 and then in Stuttgart (Germany) in 1990, Chiba (Japan) in 1994, Buenos Aires (Argentina) in 1998, Vienna (Austria) in 2002, Beijing (China) in 2004, Los Angeles (USA) in 2006 and Venice, Italy; in 2008. The 9th World Congress on Computational Mechanics is held in conjunction with the 4th Asian Pacific Congress on Computational Mechanics under the auspices of Australian Association for Computational Mechanics (AACM), Asian Pacific Association for Computational Mechanics (APACM) and International Association for Computational Mechanics (IACM). The 1st Asian Pacific Congress was in Sydney (Australia) in 2001, then in Beijing (China) in 2004 and Kyoto (Japan) in 2007. The WCCM/APCOM 2010 publications consist of a printed book of abstracts given to delegates, along with 247 full length peer reviewed papers published with

  6. Longitudinal heterogeneity of flow and heat fluxes in a large lowland river: A study of the San Joaquin River, CA, USA during a large-scale flow experiment

    Science.gov (United States)

    Bray, E. N.; Dunne, T.; Dozier, J.

    2011-12-01

    Systematic downstream variation of channel characteristics, scaled by flow affects the transport and distribution of heat throughout a large river. As water moves through a river channel, streamflow and velocity may fluctuate by orders of magnitude primarily due to channel geometry, slope and resistance to flow, and the time scales of those fluctuations range from days to decades (Constantz et al., 1994; Lundquist and Cayan, 2002; McKerchar and Henderson, 2003). It is well understood that the heat budget of a river is primarily governed by surface exchanges, with the most significant surface flux coming from net shortwave radiation. The absorption of radiation at a given point in a river is determined by the wavelength-dependent index of refraction, expressed by the angle of refraction and the optical depth as a function of physical depth and the absorption coefficient (Dozier, 1980). Few studies consider the influence of hydrologic alteration to the optical properties governing net radiative heat transfer in a large lowland river, yet it is the most significant component of the heat budget and definitive to a river's thermal regime. We seek a physically based model without calibration to incorporate scale-dependent physical processes governing heat and flow dynamics in large rivers, how they change across the longitudinal profile, and how they change under different flow regimes. Longitudinal flow and heat flux analyses require synoptic flow time series from multiple sites along rivers, and few hydrometric networks meet this requirement (Larned et al, 2011). We model the energy budget in a regulated 240-km mainstem reach of the San Joaquin River California, USA equipped with multiple gaging stations from Friant Dam to its confluence with the Merced River during a large-scale flow experiment. We use detailed hydroclimatic observations distributed across the longitudinal gradient creating a non-replicable field experiment of heat fluxes across a range of flow regime

  7. Experiment for water-flow measurement by pulsed-neutron activation

    International Nuclear Information System (INIS)

    Drozdowicz, K.

    1994-08-01

    An experiment is presented which constitutes a feasibility study for applying the neutron activation method for measurement of the water mass transport in pipings, e.g. in nuclear power stations. The fast neutron generator has been used as a pulsed-neutron activation source for oxygen in water which circulated in a closed system. The γ radiation of the nitrogen product isotope has been measured by the scintillation detectors placed in two positions at the piping. The two time distributions of the pulses have been recorded by a multiscaler (a software design based on CAMAC). The water flow velocity has been estimated from the peak-to-peak time distance. The tests have been performed under different experimental conditions (the neutron pulse duration, the time channel width, the water flow velocity) to define the stability, reproducibility and reliability of the measurement. The detailed results are presented in tables and in time distribution plots. The method has been found useful for the application considered. 4 refs, 17 figs, 5 tabs

  8. A summary of computational experience at GE Aircraft Engines for complex turbulent flows in gas turbines

    Science.gov (United States)

    Zerkle, Ronald D.; Prakash, Chander

    1995-01-01

    This viewgraph presentation summarizes some CFD experience at GE Aircraft Engines for flows in the primary gaspath of a gas turbine engine and in turbine blade cooling passages. It is concluded that application of the standard k-epsilon turbulence model with wall functions is not adequate for accurate CFD simulation of aerodynamic performance and heat transfer in the primary gas path of a gas turbine engine. New models are required in the near-wall region which include more physics than wall functions. The two-layer modeling approach appears attractive because of its computational complexity. In addition, improved CFD simulation of film cooling and turbine blade internal cooling passages will require anisotropic turbulence models. New turbulence models must be practical in order to have a significant impact on the engine design process. A coordinated turbulence modeling effort between NASA centers would be beneficial to the gas turbine industry.

  9. The COSIMA-experiments, a data base for validation of two-phase flow computer codes

    International Nuclear Information System (INIS)

    Class, G.; Meyder, R.; Stratmanns, E.

    1985-12-01

    The report presents an overview on the large data base generated with COSIMA. The data base is to be used to validate and develop computer codes for two-phase flow. In terms of fuel rod behavior it was found that during blowdown under realistic conditions only small strains are reached. For clad rupture extremely high rod internal pressure is necessary. Additionally important results were found in the behavior of a fuel rod simulator and on the effect of thermocouples attached on the cladding outer surface. Post-test calculations, performed with the codes RELAP and DRUFAN show a good agreement with the experiments. This however can be improved if the phase separation models in the codes would be updated. (orig./HP) [de

  10. Performance study of the anisotropic flow and reaction plane reconstruction in the CBM experiment

    International Nuclear Information System (INIS)

    Mikhaylov, V; Kugler, A; Kushpil, V; Tlustý, P; Selyuzhenkov, I

    2016-01-01

    The Projectile Spectator Detector (PSD) is a subsystem of the CBM experiment at the future FAIR facility designed to determine centrality and reaction plane orientation in the heavy-ion collisions. It will be done by measurement of the energy distribution of the heavy nucleons and nuclei fragments emitted close to the beam rapidity in forward direction. For the anticipated beam energies of FAIR SIS100 and SIS300 accelerators, different event generators (iQMD, UrQMD, DCM-QGSM, LA-QGSM and HSD) were used for the study of directed and elliptic proton flow in Au+Au collisions. Produced particles were transported with the GEANT4 Monte-Carlo using the CBM detector geometry. Performance of the reaction plane determination is shown for different PSD setups to demonstrate effects of the detector granularity and magnetic field. Simulation results are compared with the FOPI, AGS E877, E895 and STAR experimental data. (paper)

  11. Variably Saturated Flow and Multicomponent Biogeochemical Reactive Transport Modeling of a Uranium Bioremediation Field Experiment

    International Nuclear Information System (INIS)

    Yabusaki, Steven B.; Fang, Yilin; Williams, Kenneth H.; Murray, Christopher J.; Ward, Anderson L.; Dayvault, Richard; Waichler, Scott R.; Newcomer, Darrell R.; Spane, Frank A.; Long, Philip E.

    2011-01-01

    Field experiments at a former uranium mill tailings site have identified the potential for stimulating indigenous bacteria to catalyze the conversion of aqueous uranium in the +6 oxidation state to immobile solid-associated uranium in the +4 oxidation state. This effectively removes uranium from solution resulting in groundwater concentrations below actionable standards. Three-dimensional, coupled variably-saturated flow and biogeochemical reactive transport modeling of a 2008 in situ uranium bioremediation field experiment is used to better understand the interplay of transport rates and biogeochemical reaction rates that determine the location and magnitude of key reaction products. A comprehensive reaction network, developed largely through previous 1-D modeling studies, was used to simulate the impacts on uranium behavior of pulsed acetate amendment, seasonal water table variation, spatially-variable physical (hydraulic conductivity, porosity) and geochemical (reactive surface area) material properties. A principal challenge is the mechanistic representation of biologically-mediated terminal electron acceptor process (TEAP) reactions whose products significantly alter geochemical controls on uranium mobility through increases in pH, alkalinity, exchangeable cations, and highly reactive reduction products. In general, these simulations of the 2008 Big Rusty acetate biostimulation field experiment in Rifle, Colorado confirmed previously identified behaviors including (1) initial dominance by iron reducing bacteria that concomitantly reduce aqueous U(VI), (2) sulfate reducing bacteria that become dominant after ∼30 days and outcompete iron reducers for the acetate electron donor, (3) continuing iron-reducer activity and U(VI) bioreduction during dominantly sulfate reducing conditions, and (4) lower apparent U(VI) removal from groundwater during dominantly sulfate reducing conditions. New knowledge on simultaneously active metal and sulfate reducers has been

  12. Evaluation of diffusion parameters of radon in porous material by flow-through diffusion experiment

    International Nuclear Information System (INIS)

    Chunnan Hsu; Shihchin Tsai; Shihming Liang

    1994-01-01

    The effectiveness of a material in reducing the fluence rate of Rn from soil was assessed in this study by using a flow-through diffusion experiment to evaluate the diffusion parameters -apparent diffusion coefficient and capacity factor - of radon (Rn) in a porous material. An improved method based on the nonlinear least-squares and Marquardt's method (NLSM method) was proposed to provide more reliable analyses of experimental data than the graphical method. The NLSM method was confirmed by the experimental results to be capable of estimating the diffusion parameters, even if the process was transient. This method was also demonstrated to correlate sufficiently with the results by the conventional method while the process had already reached steady-state. Natural mordenite was employed in this study as a testing material because it has more effective sorption for noble gas than any other earthen material. (author)

  13. Precipitation and Hydrology Experiment Counter-Flow Spectrometer and Impactor Field Campaign Report

    Energy Technology Data Exchange (ETDEWEB)

    Poellot, Michael [University of North Dakota

    2016-03-01

    The U.S. Department of Energy (DOE)’s Atmospheric Radiation Measurement (ARM) Climate Research Facility Aerial Facility (ARM AAF) counter-flow spectrometer and impactor (CSI) probe was flown on the University of North Dakota Cessna Citation research aircraft during the Integrated Precipitation and Hydrology Experiment (IPHEX). The field campaign took place during May and June of 2014 over North Carolina and its coastal waters as part of a National Aeronautics and Space Administration (NASA) Global Precipitation Measurement validation campaign. The CSI was added to the Citation instrument suite to support the involvement of Jay Mace through the NASA Advanced Composition Explorer (ACE) satellite program and flights of the NASA ER-2 aircraft, which is a civilian version of the Air Force’s U2-S reconnaissance platform. The ACE program funded extra ER-2 flights to focus on clouds that are weakly precipitating, which are also of interest to the Atmospheric System Research program sponsored by DOE.

  14. On generation of Alfvenic-like fluctuations by drift wave-zonal flow system in large plasma device experiments

    International Nuclear Information System (INIS)

    Horton, W.; Correa, C.; Chagelishvili, G. D.; Avsarkisov, V. S.; Lominadze, J. G.; Perez, J. C.; Kim, J.-H.; Carter, T. A.

    2009-01-01

    According to recent experiments, magnetically confined fusion plasmas with ''drift wave-zonal flow turbulence'' (DW-ZF) give rise to broadband electromagnetic waves. Sharapov et al. [Europhysics Conference Abstracts, 35th EPS Conference on Plasma Physics, Hersonissos, 2008, edited by P. Lalousis and S. Moustaizis (European Physical Society, Switzerland, 2008), Vol. 32D, p. 4.071] reported an abrupt change in the magnetic turbulence during L-H transitions in Joint European Torus [P. H. Rebut and B. E. Keen, Fusion Technol. 11, 13 (1987)] plasmas. A broad spectrum of Alfvenic-like (electromagnetic) fluctuations appears from ExB flow driven turbulence in experiments on the large plasma device (LAPD) [W. Gekelman et al., Rev. Sci. Instrum. 62, 2875 (1991)] facility at UCLA. Evidence of the existence of magnetic fluctuations in the shear flow region in the experiments is shown. We present one possible theoretical explanation of the generation of electromagnetic fluctuations in DW-ZF systems for an example of LAPD experiments. The method used is based on generalizing results on shear flow phenomena from the hydrodynamics community. In the 1990s, it was realized that fluctuation modes of spectrally stable nonuniform (sheared) flows are non-normal. That is, the linear operators of the flows modal analysis are non-normal and the corresponding eigenmodes are not orthogonal. The non-normality results in linear transient growth with bursts of the perturbations and the mode coupling, which causes the generation of electromagnetic waves from the drift wave-shear flow system. We consider shear flow that mimics tokamak zonal flow. We show that the transient growth substantially exceeds the growth of the classical dissipative trapped-particle instability of the system.

  15. Which daily experiences can foster well-being at work? A diary study on the interplay between flow experiences, affective commitment, and self-control demands.

    Science.gov (United States)

    Rivkin, Wladislaw; Diestel, Stefan; Schmidt, Klaus-Helmut

    2018-01-01

    Previous research has provided strong evidence for affective commitment as a direct predictor of employees' psychological well-being and as a resource that buffers the adverse effects of self-control demands as a stressor. However, the mechanisms that underlie the beneficial effects of affective commitment have not been examined yet. Drawing on the self-determination theory, we propose day-specific flow experiences as the mechanism that underlies the beneficial effects of affective commitment, because flow experiences as peaks of intrinsic motivation constitute manifestations of autonomous regulation. In a diary study covering 10 working days with N = 90 employees, we examine day-specific flow experiences as a mediator of the beneficial effects of interindividual affective commitment and a buffering moderator of the adverse day-specific effects of self-control demands on indicators of well-being (ego depletion, need for recovery, work engagement, and subjective vitality). Our results provide strong support for our predictions that day-specific flow experiences a) mediate the beneficial effects of affective commitment on employees' day-specific well-being and b) moderate (buffer) the adverse day-specific effects of self-control demands on well-being. That is, on days with high levels of flow experiences, employees were better able to cope with self-control demands whereas self-control demands translated into impaired well-being when employees experienced lower levels of day-specific flow experiences. We then discuss our findings and suggest practical implications. (PsycINFO Database Record (c) 2018 APA, all rights reserved).

  16. Two-phase flow experiments on Counter-Current Flow Limitation in a model of the hot leg of a pressurized water reactor (2015 test series)

    International Nuclear Information System (INIS)

    Beyer, Matthias; Lucas, Dirk; Pietruske, Heiko; Szalinski, Lutz

    2016-12-01

    Counter-Current Flow Limitation (CCFL) is of importance for PWR safety analyses in several accident scenarios connected with loss of coolant. Basing on the experiences obtained during a first series of hot leg tests now new experiments on counter-current flow limitation were conducted in the TOPFLOW pressure vessel. The test series comprises air-water tests at 1 and 2 bar as well as steam-water tests at 10, 25 and 50 bar. During the experiments the flow structure was observed along the hot leg model using a high-speed camera and web-cams. In addition pressure was measured at several positions along the horizontal part and the water levels in the reactor-simulator and steam-generator-simulator tanks were determined. This report documents the experimental setup including the description of operational and special measuring techniques, the experimental procedure and the data obtained. From these data flooding curves were obtained basing on the Wallis parameter. The results show a slight shift of the curves in dependency of the pressure. In addition a slight decrease of the slope was found with increasing pressure. Additional investigations concern the effects of hysteresis and the frequencies of liquid slugs. The latter ones show a dependency on pressure and the mass flow rate of the injected water. The data are available for CFD-model development and validation.

  17. Two-phase flow experiments on Counter-Current Flow Limitation in a model of the hot leg of a pressurized water reactor (2015 test series)

    Energy Technology Data Exchange (ETDEWEB)

    Beyer, Matthias; Lucas, Dirk; Pietruske, Heiko; Szalinski, Lutz

    2016-12-15

    Counter-Current Flow Limitation (CCFL) is of importance for PWR safety analyses in several accident scenarios connected with loss of coolant. Basing on the experiences obtained during a first series of hot leg tests now new experiments on counter-current flow limitation were conducted in the TOPFLOW pressure vessel. The test series comprises air-water tests at 1 and 2 bar as well as steam-water tests at 10, 25 and 50 bar. During the experiments the flow structure was observed along the hot leg model using a high-speed camera and web-cams. In addition pressure was measured at several positions along the horizontal part and the water levels in the reactor-simulator and steam-generator-simulator tanks were determined. This report documents the experimental setup including the description of operational and special measuring techniques, the experimental procedure and the data obtained. From these data flooding curves were obtained basing on the Wallis parameter. The results show a slight shift of the curves in dependency of the pressure. In addition a slight decrease of the slope was found with increasing pressure. Additional investigations concern the effects of hysteresis and the frequencies of liquid slugs. The latter ones show a dependency on pressure and the mass flow rate of the injected water. The data are available for CFD-model development and validation.

  18. Flow generated by an aerated rushton impeller: two-phase PIV experiments and numerical simulations

    NARCIS (Netherlands)

    Deen, N.G.; Solberg, Tron; Hjertager, H.

    2002-01-01

    A two-camera PIV technique was used to obtain angle resolved velocity and turbulence data of the flow in a lab-scale stirred tank, equipped with a Rushton turbine. Two cases were investigated: a single-phase flow and a gas-liquid flow. In the former case, the classical radial jet flow pattern

  19. Numerical modeling of first experiments on PbLi MHD flows in a rectangular duct with foam-based SiC flow channel insert

    Energy Technology Data Exchange (ETDEWEB)

    Smolentsev, S., E-mail: sergey@fusion.ucla.edu [University of California, Los Angeles (United States); Courtessole, C.; Abdou, M.; Sharafat, S. [University of California, Los Angeles (United States); Sahu, S. [Institute of Plasma Research (India); Sketchley, T. [University of California, Los Angeles (United States)

    2016-10-15

    Highlights: • Numerical studies were performed as a pre-experimental analysis to the experiment on MHD PbLi flows in a rectangular duct with a flow channel insert (FCI). • Dynamic testing of foam-based SiC foam-based CVD coated FCI has been performed using MaPLE facility at UCLA. • Two physical models were proposed to explain the experimental results and 3D and 2D computations performed using COMSOL, HIMAG and UCLA codes. • The obtained results suggest that more work on FCI development, fabrication and testing has to be done to assure good hermetic properties before the implementation in a fusion device. - Abstract: A flow channel insert (FCI) is the key element of the DCLL blanket concept. The FCI serves as electrical and thermal insulator to reduce the MHD pressure drop and to decouple the temperature-limited ferritic structure from the flowing hot lead-lithium (PbLi) alloy. The main focus of the paper is on numerical computations to simulate MHD flows in the first experiments on PbLi flows in a stainless steel rectangular duct with a foam-based silicon carbide (SiC) FCI. A single uninterrupted long-term (∼6500 h) test has recently been performed on a CVD coated FCI sample in the flowing PbLi in a magnetic field up to 1.5 T at the PbLi temperature of 300 °C using the MaPLE loop at UCLA. An unexpectedly high MHD pressure drop measured in this experiment suggests that a PbLi ingress into the FCI occurred in the course of the experiment, resulting in degradation of electroinsulating FCI properties. The ingress through the protective CVD layer was further confirmed by the post-experimental microscopic analysis of the FCI. The numerical modeling included 2D and 3D computations using HIMAG, COMSOL and a UCLA research code to address important flow features associated with the FCI finite length, fringing magnetic field, rounded FCI corners and also to predict changes in the MHD pressure drop in the unwanted event of a PbLi ingress. Two physical

  20. Turbulent heat mixing of a heavy liquid metal flow in the MEGAPIE target geometry-The heated jet experiment

    International Nuclear Information System (INIS)

    Stieglitz, Robert; Daubner, Markus; Batta, A.; Lefhalm, C.-H.

    2007-01-01

    The MEGAPIE target installed at the Paul-Scherrer Institute is an example of a spallation target using eutectic liquid lead-bismuth (Pb 45 Bi 55 ) both as coolant and neutron source. An adequate cooling of the target requires a conditioning of the flow, which is realized by a main flow transported in an annular gap downwards, u-turned at a hemispherical shell into a cylindrical riser tube. In order to avoid a stagnation point close to the lowest part of the shell a jet flow is superimposed to the main flow, which is directed towards to the stagnation point and flows tangentially along the shell. The heated jet experiment conducted in the THEADES loop of the KALLA laboratory is nearly 1:1 representation of the lower part of the MEGAPIE target. It is aimed to study the cooling capability of this specific geometry in dependence on the flow rate ratio (Q main /Q jet ) of the main flow (Q main ) to the jet flow (Q jet ). Here, a heated jet is injected into a cold main flow at MEGAPIE relevant flow rate ratios. The liquid metal experiment is accompanied by a water experiment in almost the same geometry to study the momentum field as well as a three-dimensional turbulent numerical fluid dynamic simulation (CFD). Besides a detailed study of the envisaged nominal operation of the MEGAPIE target with Q main /Q jet = 15 deviations from this mode are investigated in the range from 7.5 ≤ Q main /Q jet ≤ 20 in order to give an estimate on the safe operational threshold of the target. The experiment shows that, the flow pattern establishing in this specific design and the turbulence intensity distribution essentially depends on the flow rate ratio (Q main /Q jet ). All Q main /Q jet -ratios investigated exhibit an unstable time dependent behavior. The MEGAPIE design is highly sensitive against changes of this ratio. Mainly three completely different flow patterns were identified. A sufficient cooling of the lower target shell, however, is only ensured if Q main /Q jet ≤ 12