Effect of tunneling layers on the performances of floating-gate based organic thin-film transistor nonvolatile memories

Science.gov (United States)

Wang, Wei; Han, Jinhua; Ying, Jun; Xiang, Lanyi; Xie, Wenfa

2014-09-01

Two types of floating-gate based organic thin-film transistor nonvolatile memories (FG-OTFT-NVMs) were demonstrated, with poly(methyl methacrylate co glycidyl methacrylate) (P(MMA-GMA)) and tetratetracontane (TTC) as the tunneling layer, respectively. Their device performances were measured and compared. In the memory with a P(MMA-GMA) tunneling layer, typical unipolar hole transport was obtained with a relatively small mobility of 0.16 cm2/V s. The unidirectional shift of turn-on voltage (Von) due to only holes trapped/detrapped in/from the floating gate resulted in a small memory window of 12.5 V at programming/erasing voltages (VP/VE) of ±100 V and a nonzero reading voltage. Benefited from the well-ordered molecule orientation and the trap-free surface of TTC layer, a considerably high hole mobility of 1.7 cm2/V s and a visible feature of electrons accumulated in channel and trapped in floating-gate were achieved in the memory with a TTC tunneling layer. High hole mobility resulted in a high on current and a large memory on/off ratio of 600 at the VP/VE of ±100 V. Both holes and electrons were injected into floating-gate and overwritten each other, which resulted in a bidirectional Von shift. As a result, an enlarged memory window of 28.6 V at the VP/VE of ±100 V and a zero reading voltage were achieved. Based on our results, a strategy is proposed to optimize FG-OTFT-NVMs by choosing a right tunneling layer to improve the majority carrier mobility and realize ambipolar carriers injecting and trapping in the floating-gate.

Ionizing radiation effects on floating gates

International Nuclear Information System (INIS)

Cellere, G.; Paccagnella, A.; Visconti, A.; Bonanomi, M.

2004-01-01

Floating gate (FG) memories, and in particular Flash, are the dominant among modern nonvolatile memory technologies. Their performance under ionizing radiation was traditionally studied for the use in space, but has become of general interest in recent years. We are showing results on the charge loss from programmed FG arrays after 10 keV x-rays exposure. Exposure to ionizing radiation results in progressive discharge of the FG. More advanced devices, featuring smaller FG, are less sensitive to ionizing radiation that older ones. The reason is identified in the photoemission of electrons from FG, since at high doses it dominates over charge loss deriving from electron/hole pairs generation in the oxides

Effect of tunneling layers on the performances of floating-gate based organic thin-film transistor nonvolatile memories

International Nuclear Information System (INIS)

Wang, Wei; Han, Jinhua; Ying, Jun; Xiang, Lanyi; Xie, Wenfa

2014-01-01

Two types of floating-gate based organic thin-film transistor nonvolatile memories (FG-OTFT-NVMs) were demonstrated, with poly(methyl methacrylate co glycidyl methacrylate) (P(MMA-GMA)) and tetratetracontane (TTC) as the tunneling layer, respectively. Their device performances were measured and compared. In the memory with a P(MMA-GMA) tunneling layer, typical unipolar hole transport was obtained with a relatively small mobility of 0.16 cm 2 /V s. The unidirectional shift of turn-on voltage (V on ) due to only holes trapped/detrapped in/from the floating gate resulted in a small memory window of 12.5 V at programming/erasing voltages (V P /V E ) of ±100 V and a nonzero reading voltage. Benefited from the well-ordered molecule orientation and the trap-free surface of TTC layer, a considerably high hole mobility of 1.7 cm 2 /V s and a visible feature of electrons accumulated in channel and trapped in floating-gate were achieved in the memory with a TTC tunneling layer. High hole mobility resulted in a high on current and a large memory on/off ratio of 600 at the V P /V E of ±100 V. Both holes and electrons were injected into floating-gate and overwritten each other, which resulted in a bidirectional V on shift. As a result, an enlarged memory window of 28.6 V at the V P /V E of ±100 V and a zero reading voltage were achieved. Based on our results, a strategy is proposed to optimize FG-OTFT-NVMs by choosing a right tunneling layer to improve the majority carrier mobility and realize ambipolar carriers injecting and trapping in the floating-gate.

Material parameters from frequency dispersion simulation of floating gate memory with Ge nanocrystals in HfO2

Science.gov (United States)

Palade, C.; Lepadatu, A. M.; Slav, A.; Lazanu, S.; Teodorescu, V. S.; Stoica, T.; Ciurea, M. L.

2018-01-01

Trilayer memory capacitors with Ge nanocrystals (NCs) floating gate in HfO2 were obtained by magnetron sputtering deposition on p-type Si substrate followed by rapid thermal annealing at relatively low temperature of 600 °C. The frequency dispersion of capacitance and resistance was measured in accumulation regime of Al/HfO2 gate oxide/Ge NCs in HfO2 floating gate/HfO2 tunnel oxide/SiOx/p-Si/Al memory capacitors. For simulation of the frequency dispersion a complex circuit model was used considering an equivalent parallel RC circuit for each layer of the trilayer structure. A series resistance due to metallic contacts and Si substrate was necessary to be included in the model. A very good fit to the experimental data was obtained and the parameters of each layer in the memory capacitor, i.e. capacitances and resistances were determined and in turn the intrinsic material parameters, i.e. dielectric constants and resistivities of layers were evaluated. The results are very important for the study and optimization of the hysteresis behaviour of floating gate memories based on NCs embedded in oxide.

Direct probing of electron and hole trapping into nano-floating-gate in organic field-effect transistor nonvolatile memories

Energy Technology Data Exchange (ETDEWEB)

Cui, Ze-Qun; Wang, Shun; Chen, Jian-Mei; Gao, Xu; Dong, Bin, E-mail: wangsd@suda.edu.cn, E-mail: chilf@suda.edu.cn, E-mail: bdong@suda.edu.cn; Chi, Li-Feng, E-mail: wangsd@suda.edu.cn, E-mail: chilf@suda.edu.cn, E-mail: bdong@suda.edu.cn; Wang, Sui-Dong, E-mail: wangsd@suda.edu.cn, E-mail: chilf@suda.edu.cn, E-mail: bdong@suda.edu.cn [Jiangsu Key Laboratory for Carbon-Based Functional Materials and Devices, Institute of Functional Nano and Soft Materials (FUNSOM), Soochow University, Suzhou, Jiangsu 215123 (China)

2015-03-23

Electron and hole trapping into the nano-floating-gate of a pentacene-based organic field-effect transistor nonvolatile memory is directly probed by Kelvin probe force microscopy. The probing is straightforward and non-destructive. The measured surface potential change can quantitatively profile the charge trapping, and the surface characterization results are in good accord with the corresponding device behavior. Both electrons and holes can be trapped into the nano-floating-gate, with a preference of electron trapping than hole trapping. The trapped charge quantity has an approximately linear relation with the programming/erasing gate bias, indicating that the charge trapping in the device is a field-controlled process.

Direct probing of electron and hole trapping into nano-floating-gate in organic field-effect transistor nonvolatile memories

International Nuclear Information System (INIS)

Cui, Ze-Qun; Wang, Shun; Chen, Jian-Mei; Gao, Xu; Dong, Bin; Chi, Li-Feng; Wang, Sui-Dong

2015-01-01

Electron and hole trapping into the nano-floating-gate of a pentacene-based organic field-effect transistor nonvolatile memory is directly probed by Kelvin probe force microscopy. The probing is straightforward and non-destructive. The measured surface potential change can quantitatively profile the charge trapping, and the surface characterization results are in good accord with the corresponding device behavior. Both electrons and holes can be trapped into the nano-floating-gate, with a preference of electron trapping than hole trapping. The trapped charge quantity has an approximately linear relation with the programming/erasing gate bias, indicating that the charge trapping in the device is a field-controlled process

VHDL-based programming environment for Floating-Gate analog memory cell

Directory of Open Access Journals (Sweden)

Carlos Alberto dos Reis Filho

2005-02-01

Full Text Available An implementation in CMOS technology of a Floating-Gate Analog Memory Cell and Programming Environment is presented. A digital closed-loop control compares a reference value set by user and the memory output and after cycling, the memory output is updated and the new value stored. The circuit can be used as analog trimming for VLSI applications where mechanical trimming associated with postprocessing chip is prohibitive due to high costs.

Using a Floating-Gate MOS Transistor as a Transducer in a MEMS Gas Sensing System

Directory of Open Access Journals (Sweden)

Gaspar Casados-Cruz

2010-11-01

Full Text Available Floating-gate MOS transistors have been widely used in diverse analog and digital applications. One of these is as a charge sensitive device in sensors for pH measurement in solutions or using gates with metals like Pd or Pt for hydrogen sensing. Efforts are being made to monolithically integrate sensors together with controlling and signal processing electronics using standard technologies. This can be achieved with the demonstrated compatibility between available CMOS technology and MEMS technology. In this paper an in-depth analysis is done regarding the reliability of floating-gate MOS transistors when charge produced by a chemical reaction between metallic oxide thin films with either reducing or oxidizing gases is present. These chemical reactions need temperatures around 200 °C or higher to take place, so thermal insulation of the sensing area must be assured for appropriate operation of the electronics at room temperature. The operation principle of the proposal here presented is confirmed by connecting the gate of a conventional MOS transistor in series with a Fe2O3 layer. It is shown that an electrochemical potential is present on the ferrite layer when reacting with propane.

Input Stage for Low-Voltage, Low-Noise Preamplifiers Based on a Floating-Gate MOS Transistor

DEFF Research Database (Denmark)

Igor, Mucha

1997-01-01

A novel input stage for low-voltage, low-noise preamplifiers for integrated capacitive sensors is presented. The input stage of the preamplifier employs floating-gate MOS transistors which are capable of storing the operation point of the input stage over several years without any severe degradat......A novel input stage for low-voltage, low-noise preamplifiers for integrated capacitive sensors is presented. The input stage of the preamplifier employs floating-gate MOS transistors which are capable of storing the operation point of the input stage over several years without any severe...... degradation of the performance of the circuit and without the need for a repeating programming. In this way the noise originating from any resistance previously used for the definition of the operating point is avoided completely and, moreover, by avoiding the input high-pass filter both the saturation...

Low-voltage high-speed programming gate-all-around floating gate memory cell with tunnel barrier engineering

Science.gov (United States)

Hamzah, Afiq; Ezaila Alias, N.; Ismail, Razali

2018-06-01

The aim of this study is to investigate the memory performances of gate-all-around floating gate (GAA-FG) memory cell implementing engineered tunnel barrier concept of variable oxide thickness (VARIOT) of low-k/high-k for several high-k (i.e., Si3N4, Al2O3, HfO2, and ZrO2) with low-k SiO2 using three-dimensional (3D) simulator Silvaco ATLAS. The simulation work is conducted by initially determining the optimized thickness of low-k/high-k barrier-stacked and extracting their Fowler–Nordheim (FN) coefficients. Based on the optimized parameters the device performances of GAA-FG for fast program operation and data retention are assessed using benchmark set by 6 and 8 nm SiO2 tunnel layer respectively. The programming speed has been improved and wide memory window with 30% increment from conventional SiO2 has been obtained using SiO2/Al2O3 tunnel layer due to its thin low-k dielectric thickness. Furthermore, given its high band edges only 1% of charge-loss is expected after 10 years of ‑3.6/3.6 V gate stress.

A Method for Estimating the Probability of Floating Gate Prompt Charge Loss in a Radiation Environment

Science.gov (United States)

Edmonds, L. D.

2016-01-01

Since advancing technology has been producing smaller structures in electronic circuits, the floating gates in modern flash memories are becoming susceptible to prompt charge loss from ionizing radiation environments found in space. A method for estimating the risk of a charge-loss event is given.

Floating-Gate Manipulated Graphene-Black Phosphorus Heterojunction for Nonvolatile Ambipolar Schottky Junction Memories, Memory Inverter Circuits, and Logic Rectifiers.

Science.gov (United States)

Li, Dong; Chen, Mingyuan; Zong, Qijun; Zhang, Zengxing

2017-10-11

The Schottky junction is an important unit in electronics and optoelectronics. However, its properties greatly degrade with device miniaturization. The fast development of circuits has fueled a rapid growth in the study of two-dimensional (2D) crystals, which may lead to breakthroughs in the semiconductor industry. Here we report a floating-gate manipulated nonvolatile ambipolar Schottky junction memory from stacked all-2D layers of graphene-BP/h-BN/graphene (BP, black phosphorus; h-BN, hexagonal boron nitride) in a designed floating-gate field-effect Schottky barrier transistor configuration. By manipulating the voltage pulse applied to the control gate, the device exhibits ambipolar characteristics and can be tuned to act as graphene-p-BP or graphene-n-BP junctions with reverse rectification behavior. Moreover, the junction exhibits good storability properties of more than 10 years and is also programmable. On the basis of these characteristics, we further demonstrate the application of the device to dual-mode nonvolatile Schottky junction memories, memory inverter circuits, and logic rectifiers.

The GaN trench gate MOSFET with floating islands: High breakdown voltage and improved BFOM

Science.gov (United States)

Shen, Lingyan; Müller, Stephan; Cheng, Xinhong; Zhang, Dongliang; Zheng, Li; Xu, Dawei; Yu, Yuehui; Meissner, Elke; Erlbacher, Tobias

2018-02-01

A novel GaN trench gate (TG) MOSFET with P-type floating islands (FLI) in drift region, which can suppress the electric field peak at bottom of gate trench during the blocking state and prevent premature breakdown in gate oxide, is proposed and investigated by TCAD simulations. The influence of thickness, position, doping concentration and length of the FLI on breakdown voltage (BV) and specific on-resistance (Ron_sp) is studied, providing useful guidelines for design of this new type of device. Using optimized parameters for the FLI, GaN FLI TG-MOSFET obtains a BV as high as 2464 V with a Ron_sp of 3.0 mΩ cm2. Compared to the conventional GaN TG-MOSFET with the same structure parameters, the Baliga figure of merit (BFOM) is enhanced by 150%, getting closer to theoretical limit for GaN devices.

Al2O3 nanocrystals embedded in amorphous Lu2O3 high-k gate dielectric for floating gate memory application

International Nuclear Information System (INIS)

Yuan, C L; Chan, M Y; Lee, P S; Darmawan, P; Setiawan, Y

2007-01-01

The integration of nanoparticles has high potential in technological applications and opens up possibilities of the development of new devices. Compared to the conventional floating gate memory, a structure containing nanocrystals embedded in dielectrics shows high potential to produce a memory with high endurance, low operating voltage, fast write-erase speeds and better immunity to soft errors [S. Tiwari, F. Rana, H. Hanafi et al. 1996 Appl.Phys. Lett. 68, 1377]. A significant improvement on data retention [J. J. Lee, X. Wang et al. 2003 Proceedings of the VLSI Technol. Symposium, p33] can be observed when discrete nanodots are used instead of continuous floating gate as charge storage nodes because local defect related leakage can be reduced efficiently. Furthermore, using a high-k dielectric in place of the conventional SiO2 based dielectric, nanodots flash memory is able to achieve significantly improved programming efficiency and data retention [A. Thean and J. -P. Leburton, 2002 IEEE Potentials 21, 35; D. W. Kim, T. Kim and S. K. Banerjee, 2003 IEEE Trans. Electron Devices 50, 1823]. We have recently successfully developed a method to produce nanodots embedded in high-k gate dielectrics [C. L. Yuan, P. Darmawan, Y. Setiawan and P. S. Lee, 2006 Electrochemical and Solid-State Letters 9, F53; C. L. Yuan, P. Darmawan, Y. Setiawan and P. S. Lee, 2006 Europhys. Lett. 74, 177]. In this paper, we fabricated the memory structure of Al 2 O 3 nanocrystals embedded in amorphous Lu 2 O 3 high k dielectric using pulsed laser ablation. The mean size and density of the Al 2 O 3 nanocrystals are estimated to be about 5 nm and 7x1011 cm -2 , respectively. Good electrical performances in terms of large memory window and good data retention were observed. Our preparation method is simple, fast and economical

Real-time reconfigurable devices implemented in UV-light programmable floating-gate CMOS

Energy Technology Data Exchange (ETDEWEB)

Aunet, Snorre

2002-06-01

This dissertation describes using theory, computer simulations and laboratory measurements a new class of real time reconfigurable UV-programmable floating-gate circuits operating with current levels typically in the pA to {mu}A range, implemented in a standard double-poly CMOS technology. A new design method based on using the same basic two-MOSFET circuits extensively is proposed, meant for improving the opportunities to make larger FGUVMOS circuitry than previously reported. By using the same basic circuitry extensively, instead of different circuitry for basic digital functions, the goal is to ease UV-programming and test and save circuitry on chip and I/O-pads. Matching of circuitry should also be improved by using this approach. Compact circuitry can be made, reducing wiring and active components. Compared to earlier FGUVMOS approaches the number of transistors for implementing the CARRY' of a FULL-ADDER is reduced from 22 to 2. A complete FULL-ADDER can be implemented using only 8 transistors. 2-MOSFET circuits able to implement CARRY', NOR, NAND and INVERT functions are demonstrated by measurements on chip, working with power supply voltages ranging from 800 mV down to 93 mV. An 8-transistor FULL-ADDER might use 2500 times less energy than a FULL-ADDER implemented using standard cells in the same 0.6 {mu}m CMOS technology while running at 1 MHz. The circuits are also shown to be a new class of linear threshold elements, which is the basic building blocks of neural networks. Theory is developed as a help in the design of floating-gate circuits.

Dual-Gate p-GaN Gate High Electron Mobility Transistors for Steep Subthreshold Slope.

Science.gov (United States)

Bae, Jong-Ho; Lee, Jong-Ho

2016-05-01

A steep subthreshold slope characteristic is achieved through p-GaN gate HEMT with dual-gate structure. Obtained subthreshold slope is less than 120 μV/dec. Based on the measured and simulated data obtained from single-gate device, breakdown of parasitic floating-base bipolar transistor and floating gate charged with holes are responsible to increase abruptly in drain current. In the dual-gate device, on-current degrades with high temperature but subthreshold slope is not changed. To observe the switching speed of dual-gate device and transient response of drain current are measured. According to the transient responses of drain current, switching speed of the dual-gate device is about 10(-5) sec.

Theory of the synchronous motion of an array of floating flap gates oscillating wave surge converter

Science.gov (United States)

Michele, Simone; Sammarco, Paolo; d'Errico, Michele

2016-08-01

We consider a finite array of floating flap gates oscillating wave surge converter (OWSC) in water of constant depth. The diffraction and radiation potentials are solved in terms of elliptical coordinates and Mathieu functions. Generated power and capture width ratio of a single gate excited by incoming waves are given in terms of the radiated wave amplitude in the far field. Similar to the case of axially symmetric absorbers, the maximum power extracted is shown to be directly proportional to the incident wave characteristics: energy flux, angle of incidence and wavelength. Accordingly, the capture width ratio is directly proportional to the wavelength, thus giving a design estimate of the maximum efficiency of the system. We then compare the array and the single gate in terms of energy production. For regular waves, we show that excitation of the out-of-phase natural modes of the array increases the power output, while in the case of random seas we show that the array and the single gate achieve the same efficiency.

Non-volatile flash memory with discrete bionanodot floating gate assembled by protein template

International Nuclear Information System (INIS)

Miura, Atsushi; Yamashita, Ichiro; Uraoka, Yukiharu; Fuyuki, Takashi; Tsukamoto, Rikako; Yoshii, Shigeo

2008-01-01

We demonstrated non-volatile flash memory fabrication by utilizing uniformly sized cobalt oxide (Co 3 O 4 ) bionanodot (Co-BND) architecture assembled by a cage-shaped supramolecular protein template. A fabricated high-density Co-BND array was buried in a metal-oxide-semiconductor field-effect-transistor (MOSFET) structure to use as the charge storage node of a floating nanodot gate memory. We observed a clockwise hysteresis in the drain current-gate voltage characteristics of fabricated BND-embedded MOSFETs. Observed hysteresis obviously indicates a memory operation of Co-BND-embedded MOSFETs due to the charge confinement in the embedded BND and successful functioning of embedded BNDs as the charge storage nodes of the non-volatile flash memory. Fabricated Co-BND-embedded MOSFETs showed good memory properties such as wide memory windows, long charge retention and high tolerance to repeated write/erase operations. A new pathway for device fabrication by utilizing the versatile functionality of biomolecules is presented

Implementation of floating gate MOSFET in inverter for threshold voltage tunability

Directory of Open Access Journals (Sweden)

Musa F.A.S.

2017-01-01

Full Text Available This paper presents the ability of floating gate MOSFET (FGMOS threshold voltage to be programmed or tuned which is exploited to improve the performance of electronic circuit design. This special characteristic owns by FGMOS is definitely contributes towards low voltage and low power circuit design. The comparison of threshold voltage between FGMOS and conventional NMOS is done in order to prove that FGMOS is able to produce a lower threshold voltage compared to conventional NMOS. In addition, in this paper, an implementation of FGMOS into inverter circuit is also done to show the programmability of FGMOS threshold voltage. The operations of the inverter circuits are verified using Sypnopsys simulation in 0.1μm CMOS technology with supply voltage of 1.8V.

The floating-gate non-volatile semiconductor memory--from invention to the digital age.

Science.gov (United States)

Sze, S M

2012-10-01

In the past 45 years (from 1967 to 2012), the non-volatile semiconductor memory (NVSM) has emerged from a floating-gate concept to the prime technology driver of the largest industry in the world-the electronics industry. In this paper, we briefly review the historical development of NVSM and project its future trends to the year 2020. In addition, we consider NVSM's wide-range of applications from the digital cellular phone to tablet computer to digital television. As the device dimension is scaled down to the deca-nanometer regime, we expect that many innovations will be made to meet the scaling challenges, and NVSM-inspired technology will continue to enrich and improve our lives for decades to come.

Leaky Integrate-and-Fire Neuron Circuit Based on Floating-Gate Integrator

Science.gov (United States)

Kornijcuk, Vladimir; Lim, Hyungkwang; Seok, Jun Yeong; Kim, Guhyun; Kim, Seong Keun; Kim, Inho; Choi, Byung Joon; Jeong, Doo Seok

2016-01-01

The artificial spiking neural network (SNN) is promising and has been brought to the notice of the theoretical neuroscience and neuromorphic engineering research communities. In this light, we propose a new type of artificial spiking neuron based on leaky integrate-and-fire (LIF) behavior. A distinctive feature of the proposed FG-LIF neuron is the use of a floating-gate (FG) integrator rather than a capacitor-based one. The relaxation time of the charge on the FG relies mainly on the tunnel barrier profile, e.g., barrier height and thickness (rather than the area). This opens up the possibility of large-scale integration of neurons. The circuit simulation results offered biologically plausible spiking activity (circuit was subject to possible types of noise, e.g., thermal noise and burst noise. The simulation results indicated remarkable distributional features of interspike intervals that are fitted to Gamma distribution functions, similar to biological neurons in the neocortex. PMID:27242416

Ultra-Low Power Consuming Direct Radiation Sensors Based on Floating Gate Structures

Directory of Open Access Journals (Sweden)

Evgeny Pikhay

2017-07-01

Full Text Available In this paper, we report on ultra-low power consuming single poly floating gate direct radiation sensors. The developed devices are intended for total ionizing dose (TID measurements and fabricated in a standard CMOS process flow. Sensor design and operation is discussed in detail. Original array sensors were suggested and fabricated that allowed high statistical significance of the radiation measurements and radiation imaging functions. Single sensors and array sensors were analyzed in combination with the specially developed test structures. This allowed insight into the physics of sensor operations and exclusion of the phenomena related to material degradation under irradiation in the interpretation of the measurement results. Response of the developed sensors to various sources of ionizing radiation (Gamma, X-ray, UV, energetic ions was investigated. The optimal design of sensor for implementation in dosimetry systems was suggested. The roadmap for future improvement of sensor performance is suggested.

A CMOS Micro-power, Class-AB “Flipped” Voltage Follower using the quasi floating-gate technique

Directory of Open Access Journals (Sweden)

Juan Jesus Ocampo-Hidalgo

2017-05-01

Full Text Available This paper presents the design and characterization of a new analog voltage follower for low-voltage applications. The main idea is based on the “Flipped” Voltage Follower and the use of the quasi-floating gate technique for achieving class AB operation. A test cell was simulated and fabricated using a 0,5 μm CMOS technology. When the proposed circuit is supplied with VDD = 1,5 V, it presents a power consumption of only 413 μW. Measurement and experimental results show a gain bandwidth product of 10 MHz and a total harmonic distortion of 1,12 % at 1 MHz.

A gate drive circuit for gate-turn-off (GTO) devices in series stack

International Nuclear Information System (INIS)

Despe, O.

1999-01-01

A gate-turn-off (GTO) switch is under development at the Advanced Photon Source as a replacement for a thyratron switch in high power pulsed application. The high voltage in the application requires multiple GTOs connected in series. One component that is critical to the success of GTO operation is the gate drive circuit. The gate drive circuit has to provide fast high-current pulses to the GTO gate for fast turn-on and turn-off. It also has to be able to operate while floating at high voltage. This paper describes a gate drive circuit that meets these requirements

Suppressing the memory state of floating gate transistors with repeated femtosecond laser backside irradiations

Science.gov (United States)

Chambonneau, Maxime; Souiki-Figuigui, Sarra; Chiquet, Philippe; Della Marca, Vincenzo; Postel-Pellerin, Jérémy; Canet, Pierre; Portal, Jean-Michel; Grojo, David

2017-04-01

We demonstrate that infrared femtosecond laser pulses with intensity above the two-photon ionization threshold of crystalline silicon induce charge transport through the tunnel oxide in floating gate Metal-Oxide-Semiconductor transistor devices. With repeated irradiations of Flash memory cells, we show how the laser-produced free-electrons naturally redistribute on both sides of the tunnel oxide until the electric field of the transistor is suppressed. This ability enables us to determine in a nondestructive, rapid and contactless way the flat band and the neutral threshold voltages of the tested device. The physical mechanisms including nonlinear ionization, quantum tunneling of free-carriers, and flattening of the band diagram are discussed for interpreting the experiments. The possibility to control the carriers in memory transistors with ultrashort pulses holds promises for fast and remote device analyses (reliability, security, and defectivity) and for considerable developments in the growing field of ultrafast microelectronics.

Optimization of pentacene double floating gate memories based on charge injection regulated by SAM functionalization

Directory of Open Access Journals (Sweden)

S. Li

2018-02-01

Full Text Available Pentacene based double nano-floating gate memories (NFGM by using gold nanoparticles (Au NPs and reduced graphene oxide (rGO sheets as charge trapping layers are prepared and demonstrated. Particularly, the NFGM chemically treated by 2,3,4,5,6-pentafluorobenzenethiol (PFBT self-assembled monolayers (SAM exhibits excellent memory performances, including high mobility of 0.23 cm2V-1s-1, the large memory window of 51 V, and the stable retention property more than 108 s. Comparing the performances of NFGM without treating with PFBT SAM, the improving performances of the memory devices by SAM modification are explained by the increase of charge injection, which could be further investigated by XPS and UPS. In particular, the results highlight the utility of SAM modulations and controlling of charge transport in the development of organic transistor memories.

Optimization of pentacene double floating gate memories based on charge injection regulated by SAM functionalization

Science.gov (United States)

Li, S.; Guérin, D.; Lenfant, S.; Lmimouni, K.

2018-02-01

Pentacene based double nano-floating gate memories (NFGM) by using gold nanoparticles (Au NPs) and reduced graphene oxide (rGO) sheets as charge trapping layers are prepared and demonstrated. Particularly, the NFGM chemically treated by 2,3,4,5,6-pentafluorobenzenethiol (PFBT) self-assembled monolayers (SAM) exhibits excellent memory performances, including high mobility of 0.23 cm2V-1s-1, the large memory window of 51 V, and the stable retention property more than 108 s. Comparing the performances of NFGM without treating with PFBT SAM, the improving performances of the memory devices by SAM modification are explained by the increase of charge injection, which could be further investigated by XPS and UPS. In particular, the results highlight the utility of SAM modulations and controlling of charge transport in the development of organic transistor memories.

Direct label-free electrical immunodetection of transplant rejection protein biomarker in physiological buffer using floating gate AlGaN/GaN high electron mobility transistors.

Science.gov (United States)

Tulip, Fahmida S; Eteshola, Edward; Desai, Suchita; Mostafa, Salwa; Roopa, Subramanian; Evans, Boyd; Islam, Syed Kamrul

2014-06-01

Monokine induced by interferon gamma (MIG/CXCL9) is used as an immune biomarker for early monitoring of transplant or allograft rejection. This paper demonstrates a direct electrical, label-free detection method of recombinant human MIG with anti-MIG IgG molecules in physiologically relevant buffer environment. The sensor platform used is a biologically modified GaN-based high electron mobility transistor (HEMT) device. Biomolecular recognition capability was provided by using high affinity anti-MIG monoclonal antibody to form molecular affinity interface receptors on short N-hydroxysuccinimide-ester functionalized disulphide (DSP) self-assembled monolayers (SAMs) on the gold sensing gate of the HEMT device. A floating gate configuration has been adopted to eliminate the influences of external gate voltage. Preliminary test results with the proposed chemically treated GaN HEMT biosensor show that MIG can be detected for a wide range of concentration varying from 5 ng/mL to 500 ng/mL.

Study of the enhancement-mode AlGaN/GaN high electron mobility transistor with split floating gates

Science.gov (United States)

Wang, Hui; Wang, Ning; Jiang, Ling-Li; Zhao, Hai-Yue; Lin, Xin-Peng; Yu, Hong-Yu

2017-11-01

In this work, the charge storage based split floating gates (FGs) enhancement mode (E-mode) AlGaN/GaN high electron mobility transistors (HEMTs) are studied. The simulation results reveal that under certain density of two dimensional electron gas, the variation tendency of the threshold voltage (Vth) with the variation of the blocking dielectric thickness depends on the FG charge density. It is found that when the length sum and isolating spacing sum of the FGs both remain unchanged, the Vth shall decrease with the increasing FGs number but maintaining the device as E-mode. It is also reported that for the FGs HEMT, the failure of a FG will lead to the decrease of Vth as well as the increase of drain current, and the failure probability can be improved significantly with the increase of FGs number.

Non-volatile nano-floating gate memory with Pt-Fe{sub 2}O{sub 3} composite nanoparticles and indium gallium zinc oxide channel

Energy Technology Data Exchange (ETDEWEB)

Hu, Quanli [Myongji University, Department of Nano Science and Engineering (Korea, Republic of); Lee, Seung Chang; Baek, Yoon-Jae [Myongji University, Department of Materials Science and Engineering (Korea, Republic of); Lee, Hyun Ho [Myongji University, Department of Chemical Engineering (Korea, Republic of); Kang, Chi Jung [Myongji University, Department of Nano Science and Engineering (Korea, Republic of); Kim, Hyun-Mi; Kim, Ki-Bum [Seoul National University, Department of Materials Science and Engineering (Korea, Republic of); Yoon, Tae-Sik, E-mail: tsyoon@mju.ac.kr [Myongji University, Department of Nano Science and Engineering (Korea, Republic of)

2013-02-15

Non-volatile nano-floating gate memory characteristics with colloidal Pt-Fe{sub 2}O{sub 3} composite nanoparticles with a mostly core-shell structure and indium gallium zinc oxide channel layer were investigated. The Pt-Fe{sub 2}O{sub 3} nanoparticles were chemically synthesized through the preferential oxidation of Fe and subsequent pileup of Pt into the core in the colloidal solution. The uniformly assembled nanoparticles' layer could be formed with a density of {approx}3 Multiplication-Sign 10{sup 11} cm{sup -2} by a solution-based dip-coating process. The Pt core ({approx}3 nm in diameter) and Fe{sub 2}O{sub 3}-shell ({approx}6 nm in thickness) played the roles of the charge storage node and tunneling barrier, respectively. The device exhibited the hysteresis in current-voltage measurement with a threshold voltage shift of {approx}4.76 V by gate voltage sweeping to +30 V. It also showed the threshold shift of {approx}0.66 V after pulse programming at +20 V for 1 s with retention > {approx}65 % after 10{sup 4} s. These results demonstrate the feasibility of using colloidal nanoparticles with core-shell structure as gate stacks of the charge storage node and tunneling dielectric for low-temperature and solution-based processed non-volatile memory devices.

Molecular sensing using monolayer floating gate, fully depleted SOI MOSFET acting as an exponential transducer.

Science.gov (United States)

Takulapalli, Bharath R

2010-02-23

Field-effect transistor-based chemical sensors fall into two broad categories based on the principle of signal transduction-chemiresistor or Schottky-type devices and MOSFET or inversion-type devices. In this paper, we report a new inversion-type device concept-fully depleted exponentially coupled (FDEC) sensor, using molecular monolayer floating gate fully depleted silicon on insulator (SOI) MOSFET. Molecular binding at the chemical-sensitive surface lowers the threshold voltage of the device inversion channel due to a unique capacitive charge-coupling mechanism involving interface defect states, causing an exponential increase in the inversion channel current. This response of the device is in opposite direction when compared to typical MOSFET-type sensors, wherein inversion current decreases in a conventional n-channel sensor device upon addition of negative charge to the chemical-sensitive device surface. The new sensor architecture enables ultrahigh sensitivity along with extraordinary selectivity. We propose the new sensor concept with the aid of analytical equations and present results from our experiments in liquid phase and gas phase to demonstrate the new principle of signal transduction. We present data from numerical simulations to further support our theory.

Arkitekturen, Roms moderne bygningsværker

DEFF Research Database (Denmark)

Hansen, Peter Mandal

2012-01-01

Artikel om Roms moderne og nutidige arkitektur med beskrivelse og analyse af et udvalg af Roms markante bygningsværker.......Artikel om Roms moderne og nutidige arkitektur med beskrivelse og analyse af et udvalg af Roms markante bygningsværker....

New AlGaN/GaN HEMTs employing both a floating gate and a field plate

International Nuclear Information System (INIS)

Lim, Jiyong; Choi, Young-Hwan; Kim, Young-Shil; Han, Min-Koo

2010-01-01

We designed and fabricated AlGaN/GaN high-electron-mobility transistors (HEMTs) employing both a floating gate (FG) and a field plate (FP), which increase the breakdown voltage of AlGaN/GaN HEMTs significantly without sacrificing forward electric characteristics. The electric field strength at the gate-drain region of the proposed AlGaN/GaN HEMT was reduced successfully due to an increase in the number of depletion region edges. The breakdown voltage of the proposed AlGaN/GaN HEMT was 1106 V, while those of the conventional devices with only an FP or FG were 688 and 828 V, respectively. The leakage current of the proposed AlGaN/GaN HEMTs was 1.68 μA under a reverse bias of -100 V while those of the conventional devices with only an FP or FG were 3.21 and 1.91 μA, respectively, under the same condition. The forward electric characteristics of the proposed and conventional AlGaN/GaN HEMTs are similar. The maximum drain current of the proposed AlGaN/GaN HEMTs was 344 mA mm -1 while those of the conventional devices with only an FP or FG were 350 and 357 mA mm -1 , respectively. The maximum transconductance of the proposed device was 102.9 mS mm -1 , while those of the conventional devices were 97.8 and 101.9 mS mm -1 . The breakdown voltage and the leakage current of the proposed device were improved considerably without sacrificing the forward electric characteristics. It should be noted that there were no additional processing steps and mask levels compared to the conventional FP process.

HRM Cd-ROM

NARCIS (Netherlands)

drs. C.A.G. Huijsmans; ir. R.B. Opsteeg; drs. H.J.J.L. Seegers

2006-01-01

De cd-rom HRM biedt een compleet en actueel overzicht van het totale HRM-gebied. Het bevat een unieke verzameling informatie over personeelsmanagement en sociaal beleid. Deze cd-rom geeft richtlijnen, maatregelen en handige tips op het gebied van personeelsmanagement. Het is samen met het zakboek de

Cern DD4424 ROM Diode Matrix

CERN Multimedia

A diode matrix is an extremely low-density form of read-only memory. It's one of the earliest forms of ROMs (dating back to the 1950s). Each bit in the ROM is represented by the presence or absence of one diode. The ROM is easily user-writable using a soldering iron and pair of wire cutters.This diode matrix board is a floppy disk boot ROM for a PDP-11, and consists of 32 16-bit words. When you access an address on the ROM, the circuit returns the represented data from that address.

An Adaptable Neuromorphic Model of Orientation Selectivity Based On Floating Gate Dynamics

Directory of Open Access Journals (Sweden)

Priti eGupta

2014-04-01

Full Text Available The biggest challenge that the neuromorphic community faces today is to build systems that can be considered truly cognitive. Adaptation and self-organization are the two basic principles that underlie any cognitive function that the brain performs. If we can replicate this behavior in hardware, we move a step closer to our goal of having cognitive neuromorphic systems. Adaptive feature selectivity is a mechanism by which nature optimizes resources so as to have greater acuity for more abundant features. Developing neuromorphic feature maps can help design generic machines that can emulate this adaptive behavior. Most neuromorphic models that have attempted to build self-organizing systems, follow the approach of modeling abstract theoretical frameworks in hardware. While this is good from a modeling and analysis perspective, it may not lead to the most efficient hardware. On the other hand, exploiting hardware dynamics to build adaptive systems rather than forcing the hardware to behave like mathematical equations, seems to be a more robust methodology when it comes to developing actual hardware for real world applications. In this paper we use a novel time-staggered Winner Take All circuit, that exploits the adaptation dynamics of floating gate transistors, to model an adaptive cortical cell that demonstrates Orientation Selectivity, a well-known biological phenomenon observed in the visual cortex. The cell performs competitive learning, refining its weights in response to input patterns resembling different oriented bars, becoming selective to a particular oriented pattern. Different analysis performed on the cell such as orientation tuning, application of abnormal inputs, response to spatial frequency and periodic patterns reveal close similarity between our cell and its biological counterpart. Embedded in a RC grid, these cells interact diffusively exhibiting cluster formation, making way for adaptively building orientation selective maps

Creating Virtual CD-ROM Collections

Directory of Open Access Journals (Sweden)

Kam Woods

2009-10-01

Full Text Available Over the past 20 years, more than 100,000 CD-ROM titles have been published including thousands of collections of government documents and data. CD-ROMs present preservation challenges at the bit level and in ensuring usability of the preserved artifact. We present techniques we have developed to archive and support user access to a collection of approximately 2,900 CD-ROMs published under the Federal Depository Library Program (FDLP by the United States Government Printing Office (GPO. The project provides web-based access to CD-ROM contents using both migration and emulation and supports remote execution of the raw CD-ROM images. Our project incorporates off-the-shelf, primarily open-source software. The raw data and (METS metadata are made available through AFS, a standard distributed file system, to encourage sharing among libraries.

CD-ROMs in Astronomy

Science.gov (United States)

Robertson, K.

The CD-ROM has become a major data storage medium in astronomy. The release of the Digitized Sky Survey is the most recent example of this phenomena. I will summarize the large scale jukebox technologies available for making the DSS available over LANs (Local Area Networks). I will also give an overview of the developments in disciplines such as medicine, chemistry and business, where CD-ROMs have been used to distribute the full text of journals. These factors may give us insights into the future role of CD-ROMs.

Bio Organic-Semiconductor Field-Effect Transistor (BioFET) Based on Deoxyribonucleic Acid (DNA) Gate Dielectric

Science.gov (United States)

2010-03-31

floating gate devices and metal-insulator-oxide-semiconductor (MIOS) devices. First attempts to use polarizable gate insulators in combination with...bulk of the semiconductor (ii) Due to the polarizable gate dielectric (iii) dipole polarization and (iv)electret effect due to mobile ions in the...characterization was carried out under an argon environment inside the glove box. An Agilent model E5273A with a two source-measurement unit instrument was

CD-ROM-aided Databases

Science.gov (United States)

Masuyama, Keiichi

CD-ROM has rapidly evolved as a new information medium with large capacity, In the U.S. it is predicted that it will become two hundred billion yen market in three years, and thus CD-ROM is strategic target of database industry. Here in Japan the movement toward its commercialization has been active since this year. Shall CD-ROM bussiness ever conquer information market as an on-disk database or electronic publication? Referring to some cases of the applications in the U.S. the author views marketability and the future trend of this new optical disk medium.

Nonlinear Aerodynamic ROM-Structural ROM Methodology for Inflatable Aeroelasticity in Hypersonic Atmospheric Entry, Phase I

Data.gov (United States)

National Aeronautics and Space Administration — ZONA Technology proposes to develop an innovative nonlinear structural reduced order model (ROM) - nonlinear aerodynamic ROM methodology for the inflatable...

Getting the Most from Your CD-ROM Dollars: The CD-ROM Bundle [and] The Pros and Cons of CD-ROM Bundling.

Science.gov (United States)

Sarjeant, Eric W.; O'Connor, Mary Ann

1992-01-01

Discusses and reviews CD-ROM bundles--i.e., hardware, software and CD-ROM kits--including their features, specifications, drawbacks, and prices. Recommends buying through mail order for the best selection and price. The pros and cons of bundling as a marketing strategy are discussed and a list of vendors is provided. (EA)

Development of anti-biofouling methods for gate facilities

International Nuclear Information System (INIS)

Fukuoka, Mari; Akamine, Kenichi; Iai, Yuuichi; Takatoo, Norihiro; Fukushima, Noriaki

2016-01-01

In the maintenance and management of gate facilities, a large sum of money and labor are required to remove and clean organisms that attach themselves to the facilities. That is why we developed two anti-biofouling systems, one that uses a weak electric current and another that uses ultrasonic waves. We carried out basic examinations and actual environment examinations to verify the effects of these methods. As a result, it has been confirmed that these methods effectively anti-foul the parts they are applied to, and that they can be used on gate facilities. In the future, we will evaluate their adaptability to aqueducts, such as those used in thermal and nuclear power plants, and marine structures, such as floating breakwaters, in addition to gate facilities. (author)

1T Pixel Using Floating-Body MOSFET for CMOS Image Sensors

Directory of Open Access Journals (Sweden)

Guo-Neng Lu

2009-01-01

Full Text Available We present a single-transistor pixel for CMOS image sensors (CIS. It is a floating-body MOSFET structure, which is used as photo-sensing device and source-follower transistor, and can be controlled to store and evacuate charges. Our investigation into this 1T pixel structure includes modeling to obtain analytical description of conversion gain. Model validation has been done by comparing theoretical predictions and experimental results. On the other hand, the 1T pixel structure has been implemented in different configurations, including rectangular-gate and ring-gate designs, and variations of oxidation parameters for the fabrication process. The pixel characteristics are presented and discussed.

1T Pixel Using Floating-Body MOSFET for CMOS Image Sensors.

Science.gov (United States)

Lu, Guo-Neng; Tournier, Arnaud; Roy, François; Deschamps, Benoît

2009-01-01

We present a single-transistor pixel for CMOS image sensors (CIS). It is a floating-body MOSFET structure, which is used as photo-sensing device and source-follower transistor, and can be controlled to store and evacuate charges. Our investigation into this 1T pixel structure includes modeling to obtain analytical description of conversion gain. Model validation has been done by comparing theoretical predictions and experimental results. On the other hand, the 1T pixel structure has been implemented in different configurations, including rectangular-gate and ring-gate designs, and variations of oxidation parameters for the fabrication process. The pixel characteristics are presented and discussed.

MBE-grown Si and Si1−xGex quantum dots embedded within epitaxial Gd2O3 on Si(111) substrate for floating gate memory device

International Nuclear Information System (INIS)

Manna, S; Aluguri, R; Katiyar, A; Ray, S K; Das, S; Laha, A; Osten, H J

2013-01-01

Si and Si 1−x Ge x quantum dots embedded within epitaxial Gd 2 O 3 grown by molecular beam epitaxy have been studied for application in floating gate memory devices. The effect of interface traps and the role of quantum dots on the memory properties have been studied using frequency-dependent capacitance–voltage and conductance–voltage measurements. Multilayer quantum dot memory comprising four and five layers of Si quantum dots exhibits a superior memory window to that of single-layer quantum dot memory devices. It has also been observed that single-layer Si 1−x Ge x quantum dots show better memory characteristics than single-layer Si quantum dots. (paper)

ROM a primera vista = ROM at first sight

Directory of Open Access Journals (Sweden)

Hugo Ricardo, D

2006-09-01

Full Text Available RESUMEN Objetivo:Es por todos conocida la importancia en la medición delROM (Range of motion: Rango de movimiento de una articulación, como elemento diagnóstico y evolutivo, pero, falta de uniformidad existe respecto a como debería ser registrado el ROM, de manera tal que otros profesionales pudieran interpretar los mismos resultados. Es objetivo de este trabajo, presentar una nueva técnica, rápida y eficaz para medir el ROM activo de las articulaciones de muñeca y dedos, sin necesidad de recurrir a un goniómetro o sistema similar.Material y métodos: La técnica se basa en darle a cada rango articular, desde la posición extrema, un valor máximo de 1 y un mínimo de 0 . Por ejemplo, si la extensión de muñeca es total, entonces corresponde valor 1; si la extensión de muñeca, no existe, entonces corresponde un valor de 0. Si la extensión llega a un 25% , se considera valor¼. Si la extensión llega a un 50%, se considera valor ½ .Si la extensión llega a un 75%, se considera valor ¾. Además, si al valor del ROM obtenido, le adosamos luego de un guión el valor 0, indicaráausencia de dolor. Si adosamos el valor 1, indicará presencia de dolor.Discusión: Esta técnica tiene evidentemente ciertas ventajas respecto a los métodos convencionales: Es más rápida, más cómoda, más simple, más fácil de aprender y recordar, y otros profesionales pueden apropiadamente interpretar los mismos resultados ABSTRACTObjective: we all are aware of the importance of the measuring of ROM in an articulation, as an element for diagnosis and evolution. Notwithstanding, there is a lack of uniformity concerning its registration to facilitate theinterpretation of the same results by other professionals.So that, the aim of this work is presenting a new, quick and effective technique to measure the active ROM of wrist and fingers joints without resorting to a goniometer or similar device.Material and methods: this technique consists of giving each

Transparent nanoscale floating gate memory using self-assembled bismuth nanocrystals in Bi(2) Mg(2/3) Nb(4/3) O(7) (BMN) pyrochlore thin films grown at room temperature.

Science.gov (United States)

Jung, Hyun-June; Yoon, Soon-Gil; Hong, Soon-Ku; Lee, Jeong-Yong

2012-07-03

Bismuth nanocrystals for a nanoscale floating gate memory device are self-assembled in Bi(2) Mg(2/3) Nb(4/3) O(7) (BMN) dielectric films grown at room temperature by radio-frequency sputtering. The TEM cross-sectional image shows the "real" structure grown on a Si (001) substrate. The image magnified from the dotted box (red color) in the the cross-sectional image clearly shows bismuth nanoparticles at the interface between the Al(2) O(3) and HfO(2) layer (right image). Nanoparticles approximately 3 nm in size are regularly distributed at the interface. Copyright © 2012 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Annelids. A Multimedia CD-ROM. [CD-ROM].

Science.gov (United States)

2001

This CD-ROM is designed for classroom and individual use to teach and learn about annelids. Integrated animations, custom graphics, three-dimensional representations, photographs, and sound are featured for use in user-controlled activities. Interactive lessons are available to reinforce the subject material. Pre- and post-testing sections are…

CD-RW/DVD-ROM drive SD-R1002; CD-RW/DVD-ROM drive SD-R1002

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

With the availability of DVD programs increasing at a rapid rate, it has become a general practice to equip a personal computer with a DVD-ROM drive. Toshiba, with a view to meeting the sharp increase in the demand for CD-R/RW (Recordable/ReWritable) recording these days, has commercialized a CD-R/RW drive capable of DVD-ROM reproduction and thereby newly entered into the CD-R/RW drive market. The new product is characterized by (1) the height halved to 41.5mm, (2) quad-speed CD-R/RW recording, (3) 24-speed CD-ROM playback at the maximum, (4) 4.8-speed DVD-ROM playback at the maximum, (5) ATAPI (AT Packet Interface) interface, and (6) access at high speeds, 160ms for DVD and 110ms for CD. (translated by NEDO)

New fabrication technique using side-wall-type plasma-enhanced chemical-vapor deposition for a floating gate memory with a Si nanodot

Energy Technology Data Exchange (ETDEWEB)

Ichikawa, Kazunori; Punchaipetch, Prakaipetch; Yano, Hiroshi; Hatayama, Tomoaki; Uraoka, Yukiharu; Fuyuki, Takashi [Nara Institute of Science and Techonology, Ikoma, Nara (Japan); Tomyo, Atsushi; Takahashi, Eiji; Hayashi, Tsukasa; Ogata, Kiyoshi [Nissin Electric Co., Ltd., Kyoto (Japan)

2006-08-15

We have used side-wall-type plasma-enhanced chemical-vapor deposition (PECVD)to fabricate a floating gate memory using a Si nano-crystal dot on thermal SiO{sub 2} at a low temperature of 430 .deg. C. Atomic and radical hydrogen plays an important role in the low-temperature formation of the dot. Transmission electron microscopy (TEM) and atomic force microscopy (AFM) analyses revealed that the average dot size and density were approximately 5 nm and 8.5 X 10{sup 11} cm{sup -2}, respectively. The electronic properties were investigated with metal-oxide-semiconductor-field-effect transistors (MOSFETs) by embedding the nanocrystal dots into SiO{sub 2} fabricated using CVD. Electron charging and discharging were clearly confirmed at room temperature by the transient behavior of the capacitance and the transfer curve. The number of electrons confined in a single dot was approximately one. Furthermore, we evaluated the electronic behavior by varying the bias condition or the operating temperature. The critical charge density could be confirmed to be independent of the injection condition.

Analysis of the Effect of Channel Leakage on Design, Characterization and Modelling of a High Voltage Pseudo-Floating Gate Sensor-Front-End

Directory of Open Access Journals (Sweden)

Luca Marchetti

2017-10-01

Full Text Available In this paper, we analyze the effects of channel leakage on the design, modelling and characterization of a high voltage pseudo-floating gate amplifier (PFGA used as sensor front-end. Leakages are known as a major challenge in new modern CMOS technologies, which are used to bias the PFGA, and consequently affect the behavior of the amplifier. As high voltages are desired for actuation of many types of resonating sensors, especially in ultrasound applications, PFGA implemented in high voltage and low leakage technologies, such as older CMOS fabrication processes or power MOSFET can be the only option. The challenge with these technologies used to implement the PFGA is that the leakages are very low, which affect the biasing of the floating gate. However, the numerous advantages of this type of amplifier, implemented with modern fabrication processes, such as high flexibility, compactness, low power consumption , etc. encouraged the authors to research about this topic. This work provides analysis of the working principle and the design rules for this amplifier, emphasizing the major differences between PFGA implemented in low leakage and high leakage technologies. Static and dynamic analysis, input offset and non-linearity of the PFGA are the main topics of this article. Three different design approaches are presented in this paper, in order to provide a more general design procedure and offset compensation for any low leakage PFGA. The amplifier has been simulated in AMS- 0 . 35 μ m CMOS models for supply voltages of 5 V and 10 V. Two prototypes have been realized to verify the validity of the modelling and the simulation results. Both devices have been realized by using discrete components and mounted on a printed circuit board. In this work, MOSFETs are realized by using commercial IC CD4007UB and 2N7000. Measurement results of the first prototype proved that the implementation of a low leakage PFGA is possible after that the input offset of

Leaky Integrate and Fire Neuron by Charge-Discharge Dynamics in Floating-Body MOSFET.

Science.gov (United States)

Dutta, Sangya; Kumar, Vinay; Shukla, Aditya; Mohapatra, Nihar R; Ganguly, Udayan

2017-08-15

Neuro-biology inspired Spiking Neural Network (SNN) enables efficient learning and recognition tasks. To achieve a large scale network akin to biology, a power and area efficient electronic neuron is essential. Earlier, we had demonstrated an LIF neuron by a novel 4-terminal impact ionization based n+/p/n+ with an extended gate (gated-INPN) device by physics simulation. Excellent improvement in area and power compared to conventional analog circuit implementations was observed. In this paper, we propose and experimentally demonstrate a compact conventional 3-terminal partially depleted (PD) SOI- MOSFET (100 nm gate length) to replace the 4-terminal gated-INPN device. Impact ionization (II) induced floating body effect in SOI-MOSFET is used to capture LIF neuron behavior to demonstrate spiking frequency dependence on input. MHz operation enables attractive hardware acceleration compared to biology. Overall, conventional PD-SOI-CMOS technology enables very-large-scale-integration (VLSI) which is essential for biology scale (~10 11 neuron based) large neural networks.

The Novice User and CD-ROM Database Services. ERIC Digest.

Science.gov (United States)

Schamber, Linda

This digest answers the following questions that beginning or novice users may have about CD-ROM (a compact disk with read-only memory) database services: (1) What is CD-ROM? (2) What databases are available? (3) Is CD-ROM difficult to use? (4) How much does CD-ROM cost? and (5) What is the future of CD-ROM? (15 references) (MES)

The Nuclear CD-Rom

International Nuclear Information System (INIS)

James, J.Z.

1993-01-01

September 1992 will see the publication of the first open-quotes Nuclear CD-ROMclose quotes-a Compact Disk Read-Only Memory (CD-ROM) containing both the entire Evaluated Nuclear Data Files (ENDF) library and the Evaluated Nuclear Structure Data Files (ENSDF) library. The CD-ROM will also contain codes for processing and visualizing the data, and some nuclear physics codes to use the ENDF data. Finally, the data and program files will be accompanied by fully-formatted documentation that can be read on many different workstations and microcomputers

Impact of back-gate bias on the hysteresis effect in partially depleted SOI MOSFETs

International Nuclear Information System (INIS)

Luo Jie-Xin; Chen Jing; Zhou Jian-Hua; Wu Qing-Qing; Chai Zhan; Yu Tao; Wang Xi

2012-01-01

The hysteresis effect in the output characteristics, originating from the floating body effect, has been measured in partially depleted (PD) silicon-on-insulator (SOI) MOSFETs at different back-gate biases. I D hysteresis has been developed to clarify the hysteresis characteristics. The fabricated devices show the positive and negative peaks in the I D hysteresis. The experimental results show that the I D hysteresis is sensitive to the back gate bias in 0.13-μm PD SOI MOSFETs and does not vary monotonously with the back-gate bias. Based on the steady-state Shockley-Read-Hall (SRH) recombination theory, we have successfully interpreted the impact of the back-gate bias on the hysteresis effect in PD SOI MOSFETs. (condensed matter: structural, mechanical, and thermal properties)

Distributing the Wealth: Sliding CD-ROM into the Consumer Channel.

Science.gov (United States)

Bowers, Richard A.

1994-01-01

Examines retail sales of CD-ROMs. Topics addressed include the current situation in CD-ROM retailing; channel distribution options; myths and realities of CD-ROM distribution; the distributor; affiliate labels; sales representatives; copublishers; distribution options; distributing resources; and recommendations for new CD-ROM publishers. (LRW)

Bilateral Floating Hip and Floating Knee: a Rare Complex Injury ...

African Journals Online (AJOL)

We report a rare complex injury of a 45-year-old man who sustained a bilateral floating hip and floating knee and hospitalised in our service six days after a traffic accident. The floating knees were open type III and II of Cauchoix score in phase of suppuration. He also presented with a floating ankle on the right side.

Ipsilateral Floating Hip and Floating Knee – A Rare Entity

Directory of Open Access Journals (Sweden)

Yashavantha Kumar

2013-04-01

Full Text Available Introduction: Ipsilateral floating hip and floating knee are very rare injuries. These injuries so uncommon that only three cases of similar kind have been reported. These injuries are due to high velocity injuries following motor vehicle accidents. Management of such complex injuries is a challenging task even in experienced hands as there are no standard treatment guidelines for such fractures. Case Report: We hereby report a 20 yr old male who sustained ipsilateral floating hip and ipsilateral floating knee injuries following motor vehicle accident. Patient was stabilized initially and later taken up for surgery. Patient was treated with interlocking nail for femur and tibia in the same sitting whereas acetabulam fracture was managed conservatively. At five months all the fractures united well with restoration of good range of motion in both hip and knee. Conclusion: Ipsilateral floating knee and floating hip are very rare injuries seen following high velocity motor vehicle accidents. There are no standard guidelines for treatment of those fractures as only a few cases of similar kind have been reported in literature. Early fixation and aggressive mobilization ensures fracture union and fewer complications. Keywords: Floating hip, Floating Knee, Ipsilateral.

Mawul Rom Project: Openness, obligation and reconciliation

NARCIS (Netherlands)

Brigg, M.; Tonnaer, A.A.C.

2008-01-01

Aboriginal Australian initiatives to restore balanced relationships with White Australians have recently become part of reconciliation efforts. This paper provides a contextualised report on one such initiative, the Mawul Rom cross-cultural mediation project. Viewing Mawul Rom as a diplomatic

Food Chains & Webs. A Multimedia CD-ROM. [CD-ROM].

Science.gov (United States)

2001

This CD-ROM is designed for classroom and individual use to teach and learn about food chains and food webs. Integrated animations, custom graphics, three-dimensional representations, photographs, and sound are featured for use in user-controlled activities. Interactive lessons are available to reinforce the subject material. Pre- and post-testing…

Artisanal fishing net float loss and a proposal for a float design solution

Directory of Open Access Journals (Sweden)

Paulo de Tarso Chaves

2016-03-01

Full Text Available Abstract Plastic floats from fishing nets are commonly found washed up on beaches in southern Brazil. They are usually broken and show signs of having been repaired. Characteristics of floats and interviews with fishermen suggest two main causes of float loss. First, collisions between active gear, bottom trawl nets for shrimp, and passive gear, drift nets for fish, destroy nets and release fragments of them, including floats. Second, the difficulty with which floats are inserted on the float rope of the nets when they are used near the surface. Floats are inserted to replace damaged or lost floats, or they may be removed if it is desired that the nets be used in deeper waters. Floats may thus be poorly fixed to the cables and lost. Here a new float design that offers greater safety in use and for the replacement of floats is described and tested.

A 1T Dynamic Random Access Memory Cell Based on Gated Thyristor with Surrounding Gate Structure for High Scalability.

Science.gov (United States)

Kim, Hyungjin; Kim, Sihyun; Kim, Hyun-Min; Lee, Kitae; Kim, Sangwan; Pak, Byung-Gook

2018-09-01

In this study, we investigate a one-transistor (1T) dynamic random access memory (DRAM) cell based on a gated-thyristor device utilizing voltage-driven bistability to enable high-speed operations. The structural feature of the surrounding gate using a sidewall provides high scalability with regard to constructing an array architecture of the proposed devices. In addition, the operation mechanism, I-V characteristics, DRAM operations, and bias dependence are analyzed using a commercial device simulator. Unlike conventional 1T DRAM cells utilizing the floating body effect, excess carriers which are required to be stored to make two different states are not generated but injected from the n+ cathode region, giving the device high-speed operation capabilities. The findings here indicate that the proposed DRAM cell offers distinct advantages in terms of scalability and high-speed operations.

Comment scolariser les enfants Roms? Les enfants Roms dans les dispositifs mis en place à Bordeaux Métropole.

OpenAIRE

Øhlund, Ida

2016-01-01

Dans ce mémoire, je m intéresse à la scolarisation des enfants Roms en France. Je présente la place des enfants Roms dans la scolarisation en Europe et en France. Je discute les efforts qu on fait en France pour scolariser ces enfants, et je prends comme exemple les mesures d intégration prises par les autorités de Bordeaux Métropole en expliquant les rôles des différents acteurs locaux. Dans la première partie, j essaye de présenter le groupe minoritaire européen appelé « Rom ». J aborde l h...

The planetary data system educational CD-ROM

Science.gov (United States)

Guinness, E. A.; Arvidson, R. E.; Martin, M.; Dueck, S.

1993-01-01

The Planetary Data System (PDS) is producing a special educational CD-ROM that contains samples of PDS datasets and is expected to be released in 1993. The CD-ROM will provide university-level instructors with PDS-compatible materials and information that can be used to construct student problem sets using real datasets. The main purposes of the CD-ROM are to facilitate wide use of planetary data and to introduce a large community to the PDS. To meet these objectives the Educational CD-ROM will also contain software to manipulate the data, background discussions about scientific questions that can be addressed with the data, and a suite of exercises that illustrate analysis techniques. Students will also be introduced to the SPICE concept, which is a new way of maintaining geometry and instrument information. The exercises will be presented at the freshman through graduate student levels. With simplification, some of the material should also be of use at the high school level.

Noziegums un sods Grama Svifta romānā "Dienas gaisma" un Fjodora Dostojevska romānā "Noziegums un sods"

OpenAIRE

Hohlova, Marija

2008-01-01

Šis bakalaura darbs pēta nozieguma un soda tēmu Fjodora Dostojevska romānā "Noziegums un sods" un Grema Svifta romānā "Dienas gaisma". Darbs sastāv no četrām nodaļām. Pirmajā nodaļā, kura pamatīgi aplūko nozieguma folozofiju, autore piemin integrēto pieeju nozieguma parādībai folozofijas skatījumā, kā arī analīzē nozieguma metafiziskās un socioloģiskās īpatnības uz Fjodora Dostojevska romāna "Noziegums un sods" pamata. Otrā nodaļa apraksta Fjodora Dostojevska romāna "Noziegums un sods" un Gre...

Monitoring of Postoperative Bone Healing Using Smart Trauma-Fixation Device With Integrated Self-Powered Piezo-Floating-Gate Sensors.

Science.gov (United States)

Borchani, Wassim; Aono, Kenji; Lajnef, Nizar; Chakrabartty, Shantanu

2016-07-01

Achieving better surgical outcomes in cases of traumatic bone fractures requires postoperative monitoring of changes in the growth and mechanical properties of the tissue and bones during the healing process. While current in-vivo imaging techniques can provide a snapshot of the extent of bone growth, it is unable to provide a history of the healing process, which is important if any corrective surgery is required. Monitoring the time evolution of in-vivo mechanical loads using existing technology is a challenge due to the need for continuous power while maintaining patient mobility and comfort. This paper investigates the feasibility of self-powered monitoring of the bone-healing process using our previously reported piezo-floating-gate (PFG) sensors. The sensors are directly integrated with a fixation device and operate by harvesting energy from microscale strain variations in the fixation structure. We show that the sensors can record and store the statistics of the strain evolution during the healing process for offline retrieval and analysis. Additionally, we present measurement results using a biomechanical phantom comprising of a femur fracture fixation plate; bone healing is emulated by inserting different materials, with gradually increasing elastic moduli, inside a fracture gap. The PFG sensor can effectively sense, compute, and record continuously evolving statistics of mechanical loading over a typical healing period of a bone, and the statistics could be used to differentiate between different bone-healing conditions. The proposed sensor presents a reliable objective technique to assess bone-healing progress and help decide on the removal time of the fixation device.

CD-ROM Stress.

Science.gov (United States)

Bunge, Charles A.

1991-01-01

Discussion of stress in library reference departments focuses on stress caused by CD-ROM reference tools. Topics discussed include work overload; nonreference duties; patron attitudes and behavior; staff attitudes; the need for proper staff training; and the need for library administrators to be sensitive to reference staff needs. (LRW)

Educational use of World Wide Web pages on CD-ROM.

Science.gov (United States)

Engel, Thomas P; Smith, Michael

2002-01-01

The World Wide Web is increasingly important for medical education. Internet served pages may also be used on a local hard disk or CD-ROM without a network or server. This allows authors to reuse existing content and provide access to users without a network connection. CD-ROM offers several advantages over network delivery of Web pages for several applications. However, creating Web pages for CD-ROM requires careful planning. Issues include file names, relative links, directory names, default pages, server created content, image maps, other file types and embedded programming. With care, it is possible to create server based pages that can be copied directly to CD-ROM. In addition, Web pages on CD-ROM may reference Internet served pages to provide the best features of both methods.

40 CFR 65.45 - External floating roof converted into an internal floating roof.

Science.gov (United States)

2010-07-01

... External floating roof converted into an internal floating roof. The owner or operator who elects to... 40 Protection of Environment 15 2010-07-01 2010-07-01 false External floating roof converted into an internal floating roof. 65.45 Section 65.45 Protection of Environment ENVIRONMENTAL PROTECTION...

Study of hard X-ray dose enhancement effects for some kinds of semiconductor devices

CERN Document Server

Guo Hong Xia; Chen Yu Sheng; Zhou Hui; He Chao Hui; Xie Ya Ning; Huang Yu Ying; He Wei; Hu Tian Dou

2002-01-01

Experimental results of X-ray dose enhancement effects are given for CMOS4069 and floating gate ROMs irradiated in Beijing Synchrotron Radiation Facility and in cobalt source. Shift of threshold voltage vs. total dose for CMOS4069 and the errors vs. total dose for 28f256 and 29c256 have been tested on line and the equivalent relation of total dose damage under the same accumulated dose is provided comparing the response of devices irradiated by X-ray and gamma-ray source. These results can be provided for X-ray radiation hardening technology as an effective evaluation data

CD-ROM: towards a strategy for teaching and learning.

Science.gov (United States)

Aarvold, J; Walton, G

1992-12-01

Compact Disc Read Only Memory (CD-ROM) represents an exciting innovation in nurse education yet paradoxically has a potential to induce disillusionment and frustration. Purchasers of systems may well find that their investment does not bring the benefits they had been lead to expect. CD-ROM systems have the capacity to generate huge quantities of data on an equally large number of nursing topics. Arguably this very capability ensures certain 'built-in' problems. The purpose of this articles is to provide nurse teachers with information about CD-ROM, to highlight the resource implications of CD-ROM use and to consider the relative merits of various teaching and learning methods. To be worthwhile, strategies developed must be part of an information retrieval skills programme.

Nonvolatile Memories Using Quantum Dot (QD) Floating Gates Assembled on II-VI Tunnel Insulators

Science.gov (United States)

Suarez, E.; Gogna, M.; Al-Amoody, F.; Karmakar, S.; Ayers, J.; Heller, E.; Jain, F.

2010-07-01

This paper presents preliminary data on quantum dot gate nonvolatile memories using nearly lattice-matched ZnS/Zn0.95Mg0.05S/ZnS tunnel insulators. The GeO x -cladded Ge and SiO x -cladded Si quantum dots (QDs) are self-assembled site-specifically on the II-VI insulator grown epitaxially over the Si channel (formed between the source and drain region). The pseudomorphic II-VI stack serves both as a tunnel insulator and a high- κ dielectric. The effect of Mg incorporation in ZnMgS is also investigated. For the control gate insulator, we have used Si3N4 and SiO2 layers grown by plasma- enhanced chemical vapor deposition.

Energy & Environmental Issues Interactive CD-ROM. Version 2.0. [CD-ROM].

Science.gov (United States)

Florida State Univ., Tallahassee.

This CD-ROM presents various energy and environmental topics. "Great Energy Debate" uses video clips to explore the pros and cons of solar, coal, nuclear, and oil energy sources. "Energy Plant Tour" presents a virtual tour through a plant that converts solid waste into energy. "How Stuff Works" explains energy…

DNA: The Molecule of Life. A Multimedia CD-ROM. [CD-ROM].

Science.gov (United States)

2001

This CD-ROM is designed for classroom and individual use to teach and learn about DNA. Integrated animations, custom graphics, three-dimensional representations, photographs, and sound are featured for use in user-controlled activities. Interactive lessons are available to reinforce the subject material. Pre- and post-testing sections are also…

Reactive oxygen metabolites (ROMs) are associated with cardiovascular disease in chronic hemodialysis patients.

Science.gov (United States)

Bossola, Maurizio; Vulpio, Carlo; Colacicco, Luigi; Scribano, Donata; Zuppi, Cecilia; Tazza, Luigi

2012-02-11

The aim of our study was to measure reactive oxygen metabolites (ROMs) in chronic hemodialysis (HD) patients and evaluate the possible association with cardiovascular disease (CVD) and mortality. We measured ROMs in 76 HD patients and correlated with CVD, cardiovascular (CV) events in the follow-up and all-cause and CVD-related mortality. The levels of ROMs presented a median value of 270 (238.2-303.2) CARR U (interquartile range). We created a ROC curve (ROMs levels vs. CVD) and we identified a cut-off point of 273 CARR U. Patients with ROMs levels ≥273 CARR U were significantly older, had higher C-reactive protein levels and lower creatinine concentrations. The prevalence of CVD was higher in patients with ROMs levels ≥273 (87.1%) than in those with ROMs levels <273 CARR U (17.7%; p<0.0001). ROMs levels were significantly higher in patients with CVD (317±63.8) than in those without (242.7±49.1; p<0.0001). At multiple regression analysis, age, creatinine and C-reactive protein were independent factors associated with ROMs. At multiple logistic regression analysis the association between ROMs and CVD was independent (OR: 1.02, 95% CI: 1.00-1.05; p=0.03). Twenty six patients developed cardiovascular (CV) events during the follow-up. Of these, seven were in the group with ROMs levels <273 CARR U and 19 in the group with ROMs levels ≥273 CARR U. The logistic regression analysis showed that both age (OR: 1.06, 95% CI: 1.01-1.12; p=0.013) and ROMs levels (OR: 1.10, 95% CI: 1.00-1.02; p=0.045) were independently associated with CV events in the follow-up. ROMs are independently associated with CVD and predict CV events in chronic HD patients.

Enhancing Your CD-ROM Services with Signage Systems.

Science.gov (United States)

Ekhaml, Leticia

1994-01-01

Describes how to use effective signage, or visual guidance, for more efficient use of CD-ROM technology in elementary and secondary school library media centers. Setting CD-ROM policies and procedures is considered; the use of posters, brochures, flowcharts, and other formats is discussed; and examples are included. (LRW)

Syd for Rom

DEFF Research Database (Denmark)

Frandsen, Steen Bo

Bogen fortæller historien om et af Europas mest berømte vildnisser, De Pontinske Sumpe, der strakte sig i kystlandet umiddelbart syd for Rom fra romertiden til tørlægningen og forvandlingen til landbrugsland i 1930'erne. Allerede under romerne vandt sumpen uophørligt terræn og forvandlede det fla...

FLOAT Project

DEFF Research Database (Denmark)

Sørensen, Eigil V.; Aarup, Bendt

The objective of the FLOAT project is to study the reliability of high-performance fibre-reinforced concrete, also known as Compact Reinforced Composite (CRC), for the floats of wave energy converters. In order to reach a commercial breakthrough, wave energy converters need to achieve a lower price...

FPGA Based Low Power ROM Design Using Capacitance Scaling

DEFF Research Database (Denmark)

Bansal, Meenakshi; Bansal, Neha; Saini, Rishita

2015-01-01

An ideal capacitor will not dissipate any power, but a real capacitor wil l have some power dissipation. In this work, we are going to design capacitance scaling based low power ROM design. In order to test the compatibility of this ROM design with latest i7 Processor, we are operating this ROM w...... in I/O Power, saving of 0.2% occur in Leakage Power, there will be a saving of 11.54% occur in Total Power. This design is implemented on Virtex-5 FPGA using Xilinx ISE and Verilog....

Our God is Gold: Vlashika Rom at a Crossroads?

Directory of Open Access Journals (Sweden)

Andrš Zbyněk

2016-12-01

Full Text Available This article explicates the sociocultural dynamics in the changing lives of the Vlashika Rom group in the Czech and Slovak Republics and contemplates the prospective development of this Roma subculture. To provide a better insight into the endeavour of the Vlashika Rom to maintain their integrity and into their adaptation strategies, the author outlines the genesis of this subethnic group, pointing out the historical circumstances that have formed them in the past. Contrary to former descriptions, the author provides an entirely new concept for dividing the Vlashika Rom into subgroups, identifying three distinct levels that create social boundaries within this community. He describes the way of living of this subgroup in the past as well as the relationships between the Vlashika Rom and the dominant society. Frequently antagonistic, these relationships depend on their way of life, substantially determined by the way they earn their living. The author analyses the inner resources that keep sustaining the contemporary Vlashika Rom culture and, drawing on his own experience and impulses from literature, inquires how long this anachronistic yet at the same time very adaptable culture will be able to resist the assimilation pressures deriving from the very nature of the modern national state.

Gating based on internal/external signals with dynamic correlation updates

International Nuclear Information System (INIS)

Wu Huanmei; Zhao Qingya; Berbeco, Ross I; Nishioka, Seiko; Shirato, Hiroki; Jiang, Steve B

2008-01-01

Precise localization of mobile tumor positions in real time is critical to the success of gated radiotherapy. Tumor positions are usually derived from either internal or external surrogates. Fluoroscopic gating based on internal surrogates, such as implanted fiducial markers, is accurate however requiring a large amount of imaging dose. Gating based on external surrogates, such as patient abdominal surface motion, is non-invasive however less accurate due to the uncertainty in the correlation between tumor location and external surrogates. To address these complications, we propose to investigate an approach based on hybrid gating with dynamic internal/external correlation updates. In this approach, the external signal is acquired at high frequency (such as 30 Hz) while the internal signal is sparsely acquired (such as 0.5 Hz or less). The internal signal is used to validate and update the internal/external correlation during treatment. Tumor positions are derived from the external signal based on the newly updated correlation. Two dynamic correlation updating algorithms are introduced. One is based on the motion amplitude and the other is based on the motion phase. Nine patients with synchronized internal/external motion signals are simulated retrospectively to evaluate the effectiveness of hybrid gating. The influences of different clinical conditions on hybrid gating, such as the size of gating windows, the optimal timing for internal signal acquisition and the acquisition frequency are investigated. The results demonstrate that dynamically updating the internal/external correlation in or around the gating window will reduce false positive with relatively diminished treatment efficiency. This improvement will benefit patients with mobile tumors, especially greater for early stage lung cancers, for which the tumors are less attached or freely floating in the lung.

Gating based on internal/external signals with dynamic correlation updates

Energy Technology Data Exchange (ETDEWEB)

Wu Huanmei [Purdue School of Engineering and Technology, Indiana University School of Informatics, IUPUI, Indianapolis, IN (United States); Zhao Qingya [School of Health Sciences, Purdue University, West Lafayette, IN (United States); Berbeco, Ross I [Department of Radiation Oncology, Dana-Farber/Brigham and Womens Cancer Center and Harvard Medical School, Boston, MA (United States); Nishioka, Seiko [NTT East-Japan Sapporo Hospital, Sapporo (Japan); Shirato, Hiroki [Hokkaido University Graduate School of Medicine, Sapporo (Japan); Jiang, Steve B [Department of Radiation Oncology, School of Medicine, University of California, San Diego, CA (United States)], E-mail: hw9@iupui.edu, E-mail: sbjiang@ucsd.edu

2008-12-21

Precise localization of mobile tumor positions in real time is critical to the success of gated radiotherapy. Tumor positions are usually derived from either internal or external surrogates. Fluoroscopic gating based on internal surrogates, such as implanted fiducial markers, is accurate however requiring a large amount of imaging dose. Gating based on external surrogates, such as patient abdominal surface motion, is non-invasive however less accurate due to the uncertainty in the correlation between tumor location and external surrogates. To address these complications, we propose to investigate an approach based on hybrid gating with dynamic internal/external correlation updates. In this approach, the external signal is acquired at high frequency (such as 30 Hz) while the internal signal is sparsely acquired (such as 0.5 Hz or less). The internal signal is used to validate and update the internal/external correlation during treatment. Tumor positions are derived from the external signal based on the newly updated correlation. Two dynamic correlation updating algorithms are introduced. One is based on the motion amplitude and the other is based on the motion phase. Nine patients with synchronized internal/external motion signals are simulated retrospectively to evaluate the effectiveness of hybrid gating. The influences of different clinical conditions on hybrid gating, such as the size of gating windows, the optimal timing for internal signal acquisition and the acquisition frequency are investigated. The results demonstrate that dynamically updating the internal/external correlation in or around the gating window will reduce false positive with relatively diminished treatment efficiency. This improvement will benefit patients with mobile tumors, especially greater for early stage lung cancers, for which the tumors are less attached or freely floating in the lung.

CD-ROM storing JENDL-3.2 plots and data

Energy Technology Data Exchange (ETDEWEB)

Fukahori, Tokio; Iwamoto, Osamu; Nakagawa, Tsuneo; Shibata, Keiichi; Narita, Tsutomu; Katakura, Jun-ichi; Hasegawa, Akira [Japan Atomic Energy Research Inst., Tokai, Ibaraki (Japan). Tokai Research Establishment

1998-01-01

Numerical data and graphs of Japanese Evaluated Nuclear Data Library, Version 3, Revision 2 (JENDL-3.2) have been stored into CD-ROM. JENDL-3.2 is an evaluated nuclear data library which is highly rated in the world, and consists of neutron nuclear data and secondary gamma-ray data for 340 nuclides. JENDL-3.2 has been already released through World Wide Web (WWW, http://cracker.tokai.jaeri.go.jp). For users` convenience and to promote further utilization, this CD-ROM has been produced. The data stored in CD-ROM are the original data and point-wise data (0 K and 300 K) of JENDL-3.2 and graphs of cross sections in gif, PostScript and PDF formats. These data can be retrieved by users` personal computers and engineering workstations, and also can be seen by using WWW browsers. This CD-ROM makes user completely free from downloading, which takes a lot of time, and tedious management such a treating big amount of data. (author)

Fabrication of a Silicon Nanowire on a Bulk Substrate by Use of a Plasma Etching and Total Ionizing Dose Effects on a Gate-All-Around Field-Effect Transistor

Science.gov (United States)

Moon, Dong-Il; Han, Jin-Woo; Meyyappan, Meyya

2016-01-01

The gate all around transistor is investigated through experiment. The suspended silicon nanowire for the next generation is fabricated on bulk substrate by plasma etching method. The scallop pattern generated by Bosch process is utilized to form a floating silicon nanowire. By combining anisotropic and istropic silicon etch process, the shape of nanowire is accurately controlled. From the suspended nanowire, the gate all around transistor is demonstrated. As the silicon nanowire is fully surrounded by the gate, the device shows excellent electrostatic characteristics.

Offshore floating windmills

International Nuclear Information System (INIS)

1993-10-01

The aim was to produce a general survey of the profitability of establishing floating offshore wind turbine arrays and to compare this with the cost and profitability of constructing offshore arrays with fixed foundations and arrays located on land sites. Aspects of design in all cases are described, also into relation to the special demands placed on dimensioning in relation to the types of location and foundation. The costs of the offshore arrays are evaluated in relation to capacity under conditions in Danish waters. The advantage of floating arrays is that they can be placed far out to sea where they can not be seen from the coast and thus not be considered to spoil the marine view. But as the water gets deeper the cost of floating foundations rises. It was found that it would not be technologically profitable to establish floating arrays at a depth of less than 30 - 40 meters which means that only the outer Danish waters can be taken into consideration. For depths of up to 70 meters, individual floating bases are more expensive than fixed ones but would be cheaper if a number of windmills could share the same anchor. For depths of more than 70 meters floating foundations would be the cheapest. The cost is dependent on the depth and distance from the coast and also on wind conditions. The main conclusion is that currently the cost of establishing wind turbine arrays in deeper outer waters on floating foundations is comparable to that of arrays sited at inner waters on solid foundations placed on the sea bed. (AB) (20 refs.)

Handbook of floating-point arithmetic

CERN Document Server

Muller, Jean-Michel; de Dinechin, Florent; Jeannerod, Claude-Pierre; Joldes, Mioara; Lefèvre, Vincent; Melquiond, Guillaume; Revol, Nathalie; Torres, Serge

2018-01-01

This handbook is a definitive guide to the effective use of modern floating-point arithmetic, which has considerably evolved, from the frequently inconsistent floating-point number systems of early computing to the recent IEEE 754-2008 standard. Most of computational mathematics depends on floating-point numbers, and understanding their various implementations will allow readers to develop programs specifically tailored for the standard’s technical features. Algorithms for floating-point arithmetic are presented throughout the book and illustrated where possible by example programs which show how these techniques appear in actual coding and design. The volume itself breaks its core topic into four parts: the basic concepts and history of floating-point arithmetic; methods of analyzing floating-point algorithms and optimizing them; implementations of IEEE 754-2008 in hardware and software; and useful extensions to the standard floating-point system, such as interval arithmetic, double- and triple-word arithm...

Scaffolding or Distracting: CD-ROM Storybooks and Young Readers

Science.gov (United States)

Pearman, Cathy J.; Chang, Ching-Wen

2010-01-01

CD-ROM storybooks, often referred to as electronic texts, e-books, and interactive stories, are learning tools with supplemental features such as automatic reading of text, sound effects, word pronunciations, and graphic animations which support the development of reading skills and comprehension in beginning readers. Some CD-ROM storybooks also…

[Benchmarking and other functions of ROM: back to basics].

Science.gov (United States)

Barendregt, M

2015-01-01

Since 2011 outcome data in the Dutch mental health care have been collected on a national scale. This has led to confusion about the position of benchmarking in the system known as routine outcome monitoring (rom). To provide insight into the various objectives and uses of aggregated outcome data. A qualitative review was performed and the findings were analysed. Benchmarking is a strategy for finding best practices and for improving efficacy and it belongs to the domain of quality management. Benchmarking involves comparing outcome data by means of instrumentation and is relatively tolerant with regard to the validity of the data. Although benchmarking is a function of rom, it must be differentiated form other functions from rom. Clinical management, public accountability, research, payment for performance and information for patients are all functions of rom which require different ways of data feedback and which make different demands on the validity of the underlying data. Benchmarking is often wrongly regarded as being simply a synonym for 'comparing institutions'. It is, however, a method which includes many more factors; it can be used to improve quality and has a more flexible approach to the validity of outcome data and is less concerned than other rom functions about funding and the amount of information given to patients. Benchmarking can make good use of currently available outcome data.

Review of CD Rom

African Journals Online (AJOL)

"The Virtual Surgeon consists of a ground breaking series of CD-ROMs, which aims to provide surgeons with a new and powerful training tool. It provides surgeons with the most accurate and realistic model of the knee available, and our developments in animation allow them to see all aspects of the surgical procedure.

Thoracic ROM measurement system with visual bio-feedback: system design and biofeedback evaluation.

Science.gov (United States)

Ando, Takeshi; Kawamura, Kazuya; Fujitani, Junko; Koike, Tomokazu; Fujimoto, Masashi; Fujie, Masakatsu G

2011-01-01

Patients with diseases such as chronic obstructive pulmonary disease (COPD) need to improve their thorax mobility. Thoracic ROM is one of the simplest and most useful indexes to evaluate the respiratory function. In this paper, we have proposed the prototype of a simple thoracic ROM measurement system with real-time visual bio-feedback in the chest expansion test. In this system, the thoracic ROM is measured using a wire-type linear encoder whose wire is wrapped around the thorax. In this paper, firstly, the repeatability and reliability of measured thoracic ROM was confirmed as a first report of the developed prototype. Secondly, we analyzed the effect of the bio-feedback system on the respiratory function. The result of the experiment showed that it was easier to maintain a large and stable thoracic ROM during deep breathing by using the real-time visual biofeedback system of the thoracic ROM.

Floating offshore turbines

DEFF Research Database (Denmark)

Tande, John Olav Giæver; Merz, Karl; Schmidt Paulsen, Uwe

2014-01-01

metric of energy production per unit steel mass. Floating offshore wind turbines represent a promising technology. The successful operation of HyWind and WindFloat in full scale demonstrates a well advanced technology readiness level, where further development will go into refining the concepts, cost...

Environmental awareness -- An interactive multimedia CD-ROM

Energy Technology Data Exchange (ETDEWEB)

Huntelmann, A.; Petruk, M.W.

1998-07-01

As corporations move to new and innovative ways of structuring high-performance work teams, effective training is being recognized as a key to insuring success. Time and scheduling constraints tend to limit the effectiveness of traditional approaches to training. This has led Edmonton Power Inc. to explore the use of CD-ROM based multimedia as a means of delivering individualized instruction in an effective and timely manner. This session will demonstrate a multimedia CD-ROM based course on Environmental Awareness designed for workers in the electrical utilities industry. The objective of the course is to make workers aware of their roles and responsibilities with respect to their impact on the environment. This session will also describe the instructional design strategy underlying this approach to training and will present some preliminary findings with respect to the effectiveness of this approach. Individuals who are interested in improving the effectiveness of their environmental training program as well as individuals who are interested in understanding the strengths of multimedia CD-ROM based training will find this session useful and informative.

14 CFR 27.753 - Main float design.

Science.gov (United States)

2010-01-01

... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false Main float design. 27.753 Section 27.753... STANDARDS: NORMAL CATEGORY ROTORCRAFT Design and Construction Floats and Hulls § 27.753 Main float design. (a) Bag floats. Each bag float must be designed to withstand— (1) The maximum pressure differential...

14 CFR 29.753 - Main float design.

Science.gov (United States)

2010-01-01

... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false Main float design. 29.753 Section 29.753... STANDARDS: TRANSPORT CATEGORY ROTORCRAFT Design and Construction Floats and Hulls § 29.753 Main float design. (a) Bag floats. Each bag float must be designed to withstand— (1) The maximum pressure differential...

New Access Points to ERIC--CD-ROM Versions. ERIC Digest.

Science.gov (United States)

McLaughlin, Pamela W.

This digest reviews three CD-ROM (compact disc-read only memory) versions of the ERIC (Educational Resources Information Center) database currently being delivered or tested and provides information for comparison. However, no attempt is made to recommend any one product. The advantages and disadvantages of the acquisition of CD-ROM databases are…

Regional Ocean Modeling System (ROMS): CNMI

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — Regional Ocean Modeling System (ROMS) 7-day, 3-hourly forecast for the region surrounding the Commonwealth of the Northern Mariana Islands (CNMI) at approximately...

Regional Ocean Modeling System (ROMS): Samoa

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — Regional Ocean Modeling System (ROMS) 7-day, 3-hourly forecast for the region surrounding the islands of Samoa at approximately 3-km resolution. While considerable...

Regional Ocean Modeling System (ROMS): Guam

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — Regional Ocean Modeling System (ROMS) 6-day, 3-hourly forecast for the region surrounding Guam at approximately 2-km resolution. While considerable effort has been...

Regional Ocean Modeling System (ROMS): Oahu

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — Regional Ocean Modeling System (ROMS) 7-day, 3-hourly forecast for the region surrounding the island of Oahu at approximately 1-km resolution. While considerable...

Data on the environment. Accompanying brochure of the CD ROM; Daten zur Umwelt. Begleitbroschuere zur CD-ROM

Energy Technology Data Exchange (ETDEWEB)

NONE

2009-07-15

During the past 25 years, the Federal Environmental Office (UBA) has been publishing annual data on the environmental situation in Germany. This is the most recent publication; it contains data on climate protection, resources management, environment, health and quality of life, natural cycles and environmental media, and the economic importance of environmental protection. The CD-ROM contains data and facts on all of these subjects. It provides detailed and comprehensive information on the current condition of the environment in Germany, strategies and goals of environmental policy, books and other publications for further reading, and links. The CD-ROM also contains a system of key environmental indicators which illustrates successful activities and needs for action of environmental policy. Integrated internet access ensures access to current information on the internet. (orig.)

Wave attenuation charcteristics of tethered float system

Digital Repository Service at National Institute of Oceanography (India)

Vethamony, P.

incident wave height transmitted wave height G wave number float mass number of rows of floats drag power transmitted wave power incident wave power 111 112 P. Vethamony float radius wave period time velocity and acceleration of fluid... particles, respectively wave attenuation in percentage displacement, velocity and acceleration of float, respectively amplitude of float displacement added mass damping coefficient fluid particle displacement amplitude of fluid particle displacement...

FLOAT Project - Task 1

DEFF Research Database (Denmark)

Marchalot, Tanguy; Kofoed, Jens Peter; Sørensen, Eigil V.

.com, 2011). CRC floats could be a very cost-effective technology with enhanced loading capacity and environmental resistance, and very low maintenance requirements, affecting directly the final energy price. The project involves DEXA Wave Energy Ltd, Wave Star A/S, Aalborg University and Hi-Con A......The objective of the FLOAT project is to study the reliability of high-performance fibre-reinforced concrete, also known as Compact Reinforced Composite (CRC), for the floats of wave energy converters. In order to reach commercial breakthrough, wave energy converters need to achieve a lower price...

SCUTREA Conference Proceedings, 1970-1997. 25th Anniversary CD-ROM.

Science.gov (United States)

Standing Conference on Univ. Teaching and Research in the Education of Adults.

This CD-ROM contains 693 papers on university teaching and research in the education of adults that were presented during the 27-year period from 1970 through 1997. The CD-ROM is designed to be used with the Macintosh, Windows 95, and Windows 3.1 operating systems and Adobe Acrobat Portable Document Format (version 3), which is included along with…

Floating Microparticulate Oral Diltiazem Hydrochloride Delivery ...

African Journals Online (AJOL)

Purpose: To formulate and evaluate floating microparticulate oral diltiazem delivery system for possible delivery to the heart. Method: Floating microspheres were prepared using cellulose acetate and Eudragit RS100 polymers by emulsion solvent evaporation technique. The dried floating microspheres were evaluated for ...

Field programmable gate array-assigned complex-valued computation and its limits

Energy Technology Data Exchange (ETDEWEB)

Bernard-Schwarz, Maria, E-mail: maria.bernardschwarz@ni.com [National Instruments, Ganghoferstrasse 70b, 80339 Munich (Germany); Institute of Applied Physics, TU Wien, Wiedner Hauptstrasse 8, 1040 Wien (Austria); Zwick, Wolfgang; Klier, Jochen [National Instruments, Ganghoferstrasse 70b, 80339 Munich (Germany); Wenzel, Lothar [National Instruments, 11500 N MOPac Expy, Austin, Texas 78759 (United States); Gröschl, Martin [Institute of Applied Physics, TU Wien, Wiedner Hauptstrasse 8, 1040 Wien (Austria)

2014-09-15

We discuss how leveraging Field Programmable Gate Array (FPGA) technology as part of a high performance computing platform reduces latency to meet the demanding real time constraints of a quantum optics simulation. Implementations of complex-valued operations using fixed point numeric on a Virtex-5 FPGA compare favorably to more conventional solutions on a central processing unit. Our investigation explores the performance of multiple fixed point options along with a traditional 64 bits floating point version. With this information, the lowest execution times can be estimated. Relative error is examined to ensure simulation accuracy is maintained.

Electrically floating, near vertical incidence, skywave antenna

Science.gov (United States)

Anderson, Allen A.; Kaser, Timothy G.; Tremblay, Paul A.; Mays, Belva L.

2014-07-08

An Electrically Floating, Near Vertical Incidence, Skywave (NVIS) Antenna comprising an antenna element, a floating ground element, and a grounding element. At least part of said floating ground element is positioned between said antenna element and said grounding element. The antenna is separated from the floating ground element and the grounding element by one or more electrical insulators. The floating ground element is separated from said antenna and said grounding element by one or more electrical insulators.

Type 1 Diabetes in Children: A Passport to Knowledge. [CD-ROM].

Science.gov (United States)

2001

This educational CD-ROM is designed to provide a working knowledge of diabetes and its effect on children. It is intended for parents, health care professionals, pharmacists, teachers, coaches, and child care providers. The CD-ROM examines issues related to diabetes management (food, insulin, monitoring, hypoglycemia, and illness); lifestyle; and…

A condensed review of the manageral aspects of CD-ROM network system

Energy Technology Data Exchange (ETDEWEB)

Choi, Kwang

2001-10-01

This report discussed manageral aspects of CD-ROM Network system to reduce executing errors and to provide effective information services to users. The results of this study are follows. 1) Library has to decide the type fo cd-rom network system compatible to the library. 2) A way of acquiring of system purchasing budget is commom utility budgets and has to include system maintenance budget. 3) When decides a provider, it is needed to review price, maintenance ability, statistics s/w, anti-virus functions.4) System manager would be a one wide-range of knowledge about network, equipment, s/w and needs continuous education about system. 5) The system users are required to have more basic knowledge than general users other users, library has to provide various user educations and minute user manuals. 6) Purchasing of CD-ROM for network use is essential and cost-benefit analysis between on-line DB and cd-rom for one user are needed. 7) when constructing Local DB using CD-RM NETWORK SYSTEM, library give attention to copyrigths of the cd-rom. 8) To provide good services through the system, cross cooperation between library and related departments is required.

14 CFR 23.753 - Main float design.

Science.gov (United States)

2010-01-01

... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false Main float design. 23.753 Section 23.753... STANDARDS: NORMAL, UTILITY, ACROBATIC, AND COMMUTER CATEGORY AIRPLANES Design and Construction Floats and Hulls § 23.753 Main float design. Each seaplane main float must meet the requirements of § 23.521. [Doc...

NODC Standard Product: NODC Taxonomic Code on CD-ROM (NODC Accession 0050418)

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — The content of the NODC Taxonomic Code, Version 8 CD-ROM (CD-ROM NODC-68) distributed by NODC is archived in this accession. Version 7 of the NODC Taxonomic Code...

Development and Evaluation of a Multimedia CD-ROM for Exercise During Pregnancy and Postpartum

Science.gov (United States)

Hausenblas, Heather A.; Brewer, Britton W.; Van Raalte, Judy L.; Cook, Brian; Downs, Danielle Symons; Weis, Carol Ann; Nigg, Claudio; Cruz, Amelia

2008-01-01

Objective To meet the need for an interactive product on exercise during pregnancy and postpartum, we developed and evaluated a personally-tailored multimedia CD-ROM. Methods Pregnant and postpartum women, who were randomly assigned to either the experimental group (PregXercise™ CD-ROM) or the control group (CD-ROM with neutral content), navigated through the CD-ROM for 1 hour. Main outcomes were exercise self-efficacy and knowledge. Results In analyses of covariance, compared with the control group, the experimental group had significant increases in self-efficacy and knowledge. Conclusion The multimedia CD-ROM delivering information about exercise motivation, guidelines, and prescription was effective in improving exercise self-efficacy and knowledge. Practice Implications Our preliminary results illustrate that healthcare professionals and researchers may use interactive multimedia for improving exercise behavior and related outcomes with pregnant and postpartum women. PMID:18068940

Validation of accuracy and reliability of a simple measurement device for the lumber range of motion (SMD-L-ROM)

International Nuclear Information System (INIS)

Kato, Nakayuki; Fujiwara, Atsushi; Honda, Toshio; Taneichi, Hiroshi

2007-01-01

It is important to evaluate mobility of the lumbar spine for assessment of lumbar spinal disorders and their therapeutic effects. We developed a simple measurement device for the lumbar range of motion (SMD-L-ROM) which can be installed on the trunk. SMD-L-ROM allows to evaluate mobility of the lumbar spine without x-ray exposure. Accuracy and reliability of the measurement device was assessed in this article. SMD-L-ROM comprises two metallic immobilization plates (IPs) with a vertically installed bar and a rubber band for fixation of IP to the trunk. Two IPs were installed at the level of Th12 and the sacrum. Range of motion (ROM) of the lumbar spine was measured by using SMD-L-ROM and radiographic modalities (X-ray and CT). Consistency of the measured values by both of SMD-L-ROM and radiographic modalities was evaluated. Furthermore, inter- and intra-observer agreement of measured values by SMD-L-ROM was assessed. Regarding measurement of ROM, there was a high correlation between SMD-L-ROM and X-ray/CT especially in the sagittal and axial plane. There was no significant difference in the average values of ROM between the two methods. On the other hand, SMD-L-ROM did not detect accurate position of the lumbar spine in all dimensions. There were no inter- and intra-observer errors of measured values by SMD-L-ROM. ROM of the lumbar spine was simply and economically measured with SMD-L-ROM. Accuracy and reliability of SMD-L-ROM was good enough for ROM measurement in the lumbar spine. (author)

Design issues and caching strategies for CD-ROM-based multimedia storage

Science.gov (United States)

Shastri, Vijnan; Rajaraman, V.; Jamadagni, H. S.; Venkat-Rangan, P.; Sampath-Kumar, Srihari

1996-03-01

CD-ROMs have proliferated as a distribution media for desktop machines for a large variety of multimedia applications (targeted for a single-user environment) like encyclopedias, magazines and games. With CD-ROM capacities up to 3 GB being available in the near future, they will form an integral part of Video on Demand (VoD) servers to store full-length movies and multimedia. In the first section of this paper we look at issues related to the single- user desktop environment. Since these multimedia applications are highly interactive in nature, we take a pragmatic approach, and have made a detailed study of the multimedia application behavior in terms of the I/O request patterns generated to the CD-ROM subsystem by tracing these patterns. We discuss prefetch buffer design and seek time characteristics in the context of the analysis of these traces. We also propose an adaptive main-memory hosted cache that receives caching hints from the application to reduce the latency when the user moves from one node of the hyper graph to another. In the second section we look at the use of CD-ROM in a VoD server and discuss the problem of scheduling multiple request streams and buffer management in this scenario. We adapt the C-SCAN (Circular SCAN) algorithm to suit the CD-ROM drive characteristics and prove that it is optimal in terms of buffer size management. We provide computationally inexpensive relations by which this algorithm can be implemented. We then propose an admission control algorithm which admits new request streams without disrupting the continuity of playback of the previous request streams. The algorithm also supports operations such as fast forward and replay. Finally, we discuss the problem of optimal placement of MPEG streams on CD-ROMs in the third section.

Reta'maxik Qatzij--Conociendo Nuestro Idioma (Knowing Our Language). [CD-ROM].

Science.gov (United States)

Academy for Educational Development, Washington, DC.

This CD-ROM is part of an interactive and dynamic multimedia package of information and games for learning K'iche' and Ixil. This CD-ROM includes six books in electronic format with interactive exercises that support improved bilingual and intercultural education and teacher training, specifically in the languages of K'iche' and Ixil. Books…

Floating polygon soup

OpenAIRE

Colleu , Thomas; Morin , Luce; Pateux , Stéphane; Labit , Claude

2011-01-01

International audience; This paper presents a new representation called floating polygon soup for applications like 3DTV and FTV (Free Viewpoint Television). This representation is based on 3D polygons and takes as input MVD data. It extends the previously proposed polygon soup representation which is appropriate for both compression, transmission and rendering stages. The floating polygon soup conserves these advantages while also taking into account misalignments at the view synthesis stage...

Have Floating Rates Been a Success?

Science.gov (United States)

Higham, David

1983-01-01

Floating exchange rates have not lived up to all expectations, but neither have they performed as badly as some critics have suggested. Examined are the impact of floating rates on balance of payments adjustment, domestic economic policy, and inflation and the claim that floating rates have displayed excessive fluctuations. (Author/RM)

An x ray archive on your desk: The Einstein CD-ROM's

Science.gov (United States)

Prestwich, A.; Mcdowell, J.; Plummer, D.; Manning, K.; Garcia, M.

1992-01-01

Data from the Einstein Observatory imaging proportional counter (IPC) and high resolution imager (HRI) were released on several CD-ROM sets. The sets released so far include pointed IPC and HRI observations in both simple image and detailed photon event list format, as well as the IPC slew survey. With the data on these CD-ROMS's the user can perform spatial analysis (e.g., surface brightness distributions), spectral analysis (with the IPC event lists), and timing analysis (with the IPC and HRI event lists). The next CD-ROM set will contain IPC unscreened data, allowing the user to perform custom screening to recover, for instance, data during times of lost aspect data or high particle background rates.

A new assessment of floating exchange rates

OpenAIRE

Waimann, D. R.

1981-01-01

The switch to floating exchange rates during the 1970s has given economists the first comprehensive opportunity to assess the arguments for and against floating. Much new work has been done on various aspects of floating exchange rate behaviour. This article attempts a limited survey of the evidence concerning two important issues—whether floating exchange rates are inherently unstable and whether they harm international trade.

Pricing Strategies for CD-ROM Products.

Science.gov (United States)

Rowley, J. E.

1994-01-01

Pricing strategies for subscriptions and licenses for CD-ROMs are different for single users and networks. The basic components of pricing strategies are charges for subscription, connect line, display/print, telecommunication, session rate, special commands, and special services. Highlights selected supplier pricing strategies for single users…

The floating knee

DEFF Research Database (Denmark)

Muñoz Vives, Josep; Bel, Jean-Christophe; Capel Agundez, Arantxa

2016-01-01

In 1975, Blake and McBryde established the concept of 'floating knee' to describe ipsilateral fractures of the femur and tibia.1This combination is much more than a bone lesion; the mechanism is usually a high-energy trauma in a patient with multiple injuries and a myriad of other lesions...... fixation when both fractures (femoral and tibial) are extra-articular.Plates are the 'standard of care' in cases with articular fractures.A combination of implants are required by 40% of floating knees.Associated ligamentous and meniscal lesions are common, but may be irrelevant in the case of an intra......-articular fracture which gives the worst prognosis for this type of lesion. Cite this article: Muñoz Vives K, Bel J-C, Capel Agundez A, Chana Rodríguez F, Palomo Traver J, Schultz-Larsen M, Tosounidis, T. The floating knee.EFORT Open Rev2016;1:375-382. DOI: 10.1302/2058-5241.1.000042....

Control development for floating wind

International Nuclear Information System (INIS)

Savenije, Feike; Peeringa, Johan

2014-01-01

Control of a floating wind turbine has proven to be challenging, but essential for lowering the cost of floating wind energy. Topic of a recent joint R and D project by GustoMSC, MARIN and ECN, is the concept design and verification with coupled simulations and model tests of the GustoMSC Tri-Floater. Only using an integral design approach, including mooring and control design, a cost effective system can be obtained. In this project, ECN developed a general floating wind turbine control strategy and applied this in a case study to the GustoMSC Tri-Floater and the OC3Hywind spar, both equipped with the NREL 5MW RWT. The designed controller ensures stable operation, while maintaining proper speed and power regulation. The motions of the floating support are reduced and substantial load reduction has been achieved

14 CFR 25.753 - Main float design.

Science.gov (United States)

2010-01-01

... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false Main float design. 25.753 Section 25.753 Aeronautics and Space FEDERAL AVIATION ADMINISTRATION, DEPARTMENT OF TRANSPORTATION AIRCRAFT AIRWORTHINESS STANDARDS: TRANSPORT CATEGORY AIRPLANES Design and Construction Floats and Hulls § 25.753 Main float design...

IDC Reengineering Phase 2 & 3 Rough Order of Magnitude (ROM) Cost Estimate Summary (Leveraged NDC Case).

Energy Technology Data Exchange (ETDEWEB)

Harris, James M.; Prescott, Ryan; Dawson, Jericah M.; Huelskamp, Robert M.

2014-11-01

Sandia National Laboratories has prepared a ROM cost estimate for budgetary planning for the IDC Reengineering Phase 2 & 3 effort, based on leveraging a fully funded, Sandia executed NDC Modernization project. This report provides the ROM cost estimate and describes the methodology, assumptions, and cost model details used to create the ROM cost estimate. ROM Cost Estimate Disclaimer Contained herein is a Rough Order of Magnitude (ROM) cost estimate that has been provided to enable initial planning for this proposed project. This ROM cost estimate is submitted to facilitate informal discussions in relation to this project and is NOT intended to commit Sandia National Laboratories (Sandia) or its resources. Furthermore, as a Federally Funded Research and Development Center (FFRDC), Sandia must be compliant with the Anti-Deficiency Act and operate on a full-cost recovery basis. Therefore, while Sandia, in conjunction with the Sponsor, will use best judgment to execute work and to address the highest risks and most important issues in order to effectively manage within cost constraints, this ROM estimate and any subsequent approved cost estimates are on a 'full-cost recovery' basis. Thus, work can neither commence nor continue unless adequate funding has been accepted and certified by DOE.

Networking CD-ROMs: The Decision Maker's Guide to Local Area Network Solutions.

Science.gov (United States)

Elshami, Ahmed M.

In an era when patrons want access to CD-ROM resources but few libraries can afford to buy multiple copies, CD-ROM local area networks (LANs) are emerging as a cost-effective way to provide shared access. To help librarians make informed decisions, this manual offers information on: (1) the basics of LANs, a "local area network primer";…

CD-ROM-aided Databases

Science.gov (United States)

Kusama, Hideo; Matsumoto, Toshiaki

The CD-ROM system can be used independently or as a compliment to an on-line data system. It has many of the same features as an on-line system. Nippan developed the CD-NOCS system as a reinforcement or substitute for the on-line systems of the customers (bookstores). CD-NOCS is not necessarily designed just for bookstores, it is also applicable to libraries and companies. Authors would also like to emphasize that it is important to understand the development and background of the CD-NOCS system, as well as its operations.

Intertekstualitāte Dž.K. Roulingas "Harija Potera" romānu serijā

OpenAIRE

Strunga-Raude, Aija

2009-01-01

Šī bakalaura darba tēma ir „Intertekstualitāte Dž. K. Roulingas "Harija Potera" romānu sērijā”. Es izvēlējos šo tēmu, jo 2008. gadā tika izdota pēdējā septītā grāmata šajā romānu sērijā un šīs grāmatas jau ir izraisījušas plašas diskusijas dažādās sabiedrības grupās. Šī ir lieliska iespēja izpētīt ko tieši Džoanna Ketlīna Roulinga ir izmantojusi savā romānā “Harijs Poters”. Šī darba mērķis ir ilustrēt kā Dž. K. Roulinga, rakstot „Harija Potera” romānu sēriju, ir izmantojusi intertekstualit...

Regional Ocean Modeling System (ROMS): Main Hawaiian Islands

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — Regional Ocean Modeling System (ROMS) 7-day, 3-hourly forecast for the region surrounding the main Hawaiian islands at approximately 4-km resolution. While...

Regional Ocean Modeling System (ROMS): CNMI: Data Assimilating

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — Regional Ocean Modeling System (ROMS) 3-day, 3-hourly data assimilating hindcast for the region surrounding the Commonwealth of the Northern Mariana Islands (CNMI)...

Regional Ocean Modeling System (ROMS): Samoa: Data Assimilating

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — Regional Ocean Modeling System (ROMS) 3-day, 3-hourly data assimilating hindcast for the region surrounding the islands of Samoa at approximately 3-km resolution....

Regional Ocean Modeling System (ROMS): Oahu: Data Assimilating

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — Regional Ocean Modeling System (ROMS) 2-day, 3-hourly data assimilating hindcast for the region surrounding the island of Oahu at approximately 1-km resolution....

The Basic Economics of CD-ROM Pricing.

Science.gov (United States)

Erkkila, John E.

1991-01-01

This explanation of how the basic economic model of pricing applies to the CD-ROM industry considers the supply and demand sides of the market and compares three distinct pricing strategies: (1) pricing to maximize profits; (2) average cost pricing; and (3) marginal cost pricing. (EAM)

14 CFR 29.757 - Hull and auxiliary float strength.

Science.gov (United States)

2010-01-01

... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false Hull and auxiliary float strength. 29.757... AIRCRAFT AIRWORTHINESS STANDARDS: TRANSPORT CATEGORY ROTORCRAFT Design and Construction Floats and Hulls § 29.757 Hull and auxiliary float strength. The hull, and auxiliary floats if used, must withstand the...

Regional Ocean Modeling System (ROMS): Oahu South Shore

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — Regional Ocean Modeling System (ROMS) 2-day, 3-hourly forecast for the region surrounding the south shore of the island of Oahu at approximately 200-m resolution....

Between Freedom and Constraint: ROM Hacking of Pokémon Games

OpenAIRE

Barnabé, Fanny

2018-01-01

This paper aims to study a creative practice widespread in video game cultures: “ROM hacking”. By examining with the tools of rhetoric a defined corpus of ROM hacks derived from 『Pokémon』 games, the presentation will show that the formal construction of these derivative works demonstrates less a free or subversive transformation than a fairly strict respect for the original games’ conventions. By reproducing the structure of official 『Pokémon 』games, these fan productions become mirrors revea...

Studi Korelasi Motivasi Pengguna Dengan Pemanfaatan Koleksi CD-ROM Di UPT Pusat Perpustakaan UII Yogyakarta (Study on Correlation Between The Motivation of Users and The Use of CD-ROM Collection At The Main Library of Indonesia Islamic University of Yogyakarta

Directory of Open Access Journals (Sweden)

Keni Hesti Handayani

2015-12-01

Full Text Available The research addresses three main issues: student motivation of Indonesia Islamic University of Yogyakarta, the use of CD-ROM collection at the main library of Indonesia Islamic University of Yogyakarta, and the correlation between student motivation and the use of CD-ROM collection at the library. The study uses a field research. The sample is accidental sampling which involves students using the collection of CD-ROM at the library. In the term of data collection, the writer uses some techniques those of which are documentation, observation, interview and questionnaire. The result of the research shows that, there are correlation between the motivation and the use of CD-ROM collection at the main library of Indonesia Islamic University of Yogyakarta. The research is hoped to contribute to the improvement of services of CD-ROM collection at library in particular and to the development of through collection at the library. Keyword: user motivation, the use of CD-ROM collection

Strength Tests on Hulls and Floats

Science.gov (United States)

Matthaes, K

1942-01-01

The present report deals with strength tests on hulls and floats intended in part for the collection of construction data for the design of these components and in part for the stress analysis of the finished hulls and floats.

Investigation of High-k Dielectrics and Metal Gate Electrodes for Non-volatile Memory Applications

Science.gov (United States)

Jayanti, Srikant

Due to the increasing demand of non-volatile flash memories in the portable electronics, the device structures need to be scaled down drastically. However, the scalability of traditional floating gate structures beyond 20 nm NAND flash technology node is uncertain. In this regard, the use of metal gates and high-k dielectrics as the gate and interpoly dielectrics respectively, seem to be promising substitutes in order to continue the flash scaling beyond 20nm. Furthermore, research of novel memory structures to overcome the scaling challenges need to be explored. Through this work, the use of high-k dielectrics as IPDs in a memory structure has been studied. For this purpose, IPD process optimization and barrier engineering were explored to determine and improve the memory performance. Specifically, the concept of high-k / low-k barrier engineering was studied in corroboration with simulations. In addition, a novel memory structure comprising a continuous metal floating gate was investigated in combination with high-k blocking oxides. Integration of thin metal FGs and high-k dielectrics into a dual floating gate memory structure to result in both volatile and non-volatile modes of operation has been demonstrated, for plausible application in future unified memory architectures. The electrical characterization was performed on simple MIS/MIM and memory capacitors, fabricated through CMOS compatible processes. Various analytical characterization techniques were done to gain more insight into the material behavior of the layers in the device structure. In the first part of this study, interfacial engineering was investigated by exploring La2O3 as SiO2 scavenging layer. Through the silicate formation, the consumption of low-k SiO2 was controlled and resulted in a significant improvement in dielectric leakage. The performance improvement was also gauged through memory capacitors. In the second part of the study, a novel memory structure consisting of continuous metal FG

Review of Cornaline de l'Inde/Carnelian in India CD-Rom.

Directory of Open Access Journals (Sweden)

Peter Grave

2002-10-01

Full Text Available The CD-Rom format has been around for some time now with CD-Rom readers a standard fitting on even the most basic PC. The strength of this technology is that it enables large amounts of data to be stored (650-700 MB on a reliable, portable and economical medium. The character of data stored is virtually only dependant on developments in the hardware and software used to generate and manage datasets, whether numeric arrays, databases, digital imagery or multimedia. These features have made it a popular mode for a diverse range of interactive educational, reference and entertainment software. As a medium that can hold thousand of 'pages' of text, spreadsheets, colour images, animations and digital movies, CD-Rom technology also offers obvious benefits for the delivery of the diversity of data produced by archaeological research. It is surprising then that projects such as the bilingual Cornaline de l'Inde/Carnelian in India are few and far between.

WindWaveFloat (WWF): Final Scientific Report

Energy Technology Data Exchange (ETDEWEB)

Weinstein, Alla; Roddier, Dominique; Banister, Kevin

2012-03-30

Principle Power Inc. and National Renewable Energy Lab (NREL) have completed a contract to assess the technical and economic feasibility of integrating wave energy converters into the WindFloat, resulting in a new concept called the WindWaveFloat (WWF). The concentration of several devices on one platform could offer a potential for both economic and operational advantages. Wind and wave energy converters can share the electrical cable and power transfer equipment to transport the electricity to shore. Access to multiple generation devices could be simplified, resulting in cost saving at the operational level. Overall capital costs may also be reduced, provided that the design of the foundation can be adapted to multiple devices with minimum modifications. Finally, the WindWaveFloat confers the ability to increase energy production from individual floating support structures, potentially leading to a reduction in levelized energy costs, an increase in the overall capacity factor, and greater stability of the electrical power delivered to the grid. The research conducted under this grant investigated the integration of several wave energy device types into the WindFloat platform. Several of the resulting system designs demonstrated technical feasibility, but the size and design constraints of the wave energy converters (technical and economic) make the WindWaveFloat concept economically unfeasible at this time. Not enough additional generation could be produced to make the additional expense associated with wave energy conversion integration into the WindFloat worthwhile.

Development and Utilization of Regional Oceanic Modeling System (ROMS) & Delicacy, Imprecision, and Uncertainty of Oceanic Simulations: An Investigation with ROMS

Science.gov (United States)

2010-09-30

and Ecosystems: An important community use for ROMS is biogeochemisty: chemical cycles, water quality, blooms , micro-nutrients, larval dispersal... Chile current system. J. Climate, submitted. Colas, F., X. Capet, and J. McWilliams, 2010b: Mesoscale eddy buoyancy flux and eddy-induced

Ģimene Mārgaretas Atvudas romānos

OpenAIRE

Voitiņa, Laura

2009-01-01

Mūsdienās diskusijas par ģimeni, tās vērtībām, mainīgo uzbūvi un problēmām, kas ietekmē šo institūtu, ir sastopamas ne tikai mutvārdu runā, bet arī rakstos. Dotā pētījuma mērķis bija veikt saturisku analīzi par ģimenes aprakstiem Margaretas Atvudas romānos “Istabenes Stāsts” un “Oriksa un Kreiks”, lai identificētu romānos aprakstītos ģimenes modeļus, vērtības, paražas un notikumus, kas ietekmē šo institūtu. Tika izmantotas gan teorētiskas, gan empīriskas pētījuma metodes. Lai sniegtu teorētis...

100-nm gate lithography for double-gate transistors

Science.gov (United States)

Krasnoperova, Azalia A.; Zhang, Ying; Babich, Inna V.; Treichler, John; Yoon, Jung H.; Guarini, Kathryn; Solomon, Paul M.

2001-09-01

The double gate field effect transistor (FET) is an exploratory device that promises certain performance advantages compared to traditional CMOS FETs. It can be scaled down further than the traditional devices because of the greater electrostatic control by the gates on the channel (about twice as short a channel length for the same gate oxide thickness), has steeper sub-threshold slope and about double the current for the same width. This paper presents lithographic results for double gate FET's developed at IBM's T. J. Watson Research Center. The device is built on bonded wafers with top and bottom gates self-aligned to each other. The channel is sandwiched between the top and bottom polysilicon gates and the gate length is defined using DUV lithography. An alternating phase shift mask was used to pattern gates with critical dimensions of 75 nm, 100 nm and 125 nm in photoresist. 50 nm gates in photoresist have also been patterned by 20% over-exposure of nominal 100 nm lines. No trim mask was needed because of a specific way the device was laid out. UV110 photoresist from Shipley on AR-3 antireflective layer were used. Process windows, developed and etched patterns are presented.

The systems prioritization method (SPM) CD-ROM demonstration for Waste Management '96

International Nuclear Information System (INIS)

Harris, C.L.; Boak, D.M.; Prindle, N.H.; Beyeler, W.

1996-01-01

In March 1994, the Department of Energy Carlsbad Area Office (DOE/CAO) implemented a performance-based planning method to assist in prioritization within the Waste Isolation Pilot Plant (WIPP). Probabilistic performance calculations were required for the Systems Prioritization Method (SPM) and roughly 46,700 combinations of activities were analyzed, generating a large volume of information to be documented, analyzed, and communicated. A self-contained information management system consisting of a relational database on a 600-megabyte CD-ROM was built to meet this need. The CD-ROM was used to store performance assessment results, data analysis and visualization tools, information about the activities, electronic copies of 40 ILFR 191 and 40 CFR 268, technical reference papers, and the final SPM report. Copies of the CD-ROM were distributed to interested members of the public, WIPP participants, and the Environmental Protection Agency (EPA)

Stress analysis and mitigation measures for floating pipeline

Science.gov (United States)

Wenpeng, Guo; Yuqing, Liu; Chao, Li

2017-03-01

Pipeline-floating is a kind of accident with contingency and uncertainty associated to natural gas pipeline occurring during rainy season, which is significantly harmful to the safety of pipeline. Treatment measures against pipeline floating accident are summarized in this paper on the basis of practical project cases. Stress states of pipeline upon floating are analyzed by means of Finite Element Calculation method. The effectiveness of prevention ways and subsequent mitigation measures upon pipeline-floating are verified for giving guidance to the mitigation of such accidents.

On-line vs DC-ROM delivery of information

NARCIS (Netherlands)

Waaijers, L.

1992-01-01

Considers the use of new technologies in library information delivery systems. Discusses the virtues of paper, CD-ROM, and online media in terms of accessibility, timeliness, compactness, searchability, preservability, authenticity, and appearance, as well as end user benefit. Surmises that

Use of CD-Rom databases by staff and students in the University of ...

African Journals Online (AJOL)

The focus of this study is the use of CD-ROM databases by staff and students in the university of Jos library. This is of interest as CD-ROM database services is in consonant with the vision of providing excellent and effective information services to all staff and students of university of Jos. The study was guided by six ...

Dea Computrix - another deity for the Roman Pantheon? Journeys in the Roman Empire CD-Rom

Directory of Open Access Journals (Sweden)

T. Sam N. Moorhead

2002-08-01

Full Text Available This article outlines a personal view on the content and production of a CD-Rom on the Roman world produced by The British Museum, Channel 4, Verulamium Museum and Braunarts: Journeys in the Roman Empire. I discuss some of the benefits of and problems with multimedia production and outline feedback from various evaluation projects of the CD-Rom. I also briefly discuss the future of CD-Roms in the face of a rapidly expanding internet with reference to other multimedia projects at The British Museum.

Gating-ML: XML-based gating descriptions in flow cytometry.

Science.gov (United States)

Spidlen, Josef; Leif, Robert C; Moore, Wayne; Roederer, Mario; Brinkman, Ryan R

2008-12-01

The lack of software interoperability with respect to gating due to lack of a standardized mechanism for data exchange has traditionally been a bottleneck, preventing reproducibility of flow cytometry (FCM) data analysis and the usage of multiple analytical tools. To facilitate interoperability among FCM data analysis tools, members of the International Society for the Advancement of Cytometry (ISAC) Data Standards Task Force (DSTF) have developed an XML-based mechanism to formally describe gates (Gating-ML). Gating-ML, an open specification for encoding gating, data transformations and compensation, has been adopted by the ISAC DSTF as a Candidate Recommendation. Gating-ML can facilitate exchange of gating descriptions the same way that FCS facilitated for exchange of raw FCM data. Its adoption will open new collaborative opportunities as well as possibilities for advanced analyses and methods development. The ISAC DSTF is satisfied that the standard addresses the requirements for a gating exchange standard.

Public census data on CD-ROM at Lawrence Berkeley Laboratory

Energy Technology Data Exchange (ETDEWEB)

Merrill, D.W.

1992-07-02

In connection with the Comprehensive Epidemiologic Data Resource (CEDR) and Populations at Risk to Environmental Pollution (PAREP) projects, of the Information and Computing Sciences Division (ICSD) at Lawrence Berkeley Laboratory (LBL), are using public socioeconomic and geographic data files which are available to CEDR and PAREP collaborators via LBL's computing network. At this time 67 CD-ROM diskettes (approximately 35 gigabytes) are on line via the Unix file server cedrcd.lbl.gov. Most of the files are from the US Bureau of the Census, and most pertain to the 1990 Census of Population and Housing. This paper contains a list of the CD-ROMs available.

Dispersion measurements from Sofar floats on the Iberian Abyssal plain

International Nuclear Information System (INIS)

Rees, J.M.; Gmitrowicz, M.

1989-01-01

Tracks of SOFAR floats launched on the Iberian Abyssal Plain are presented. The floats were launched in two groups in early October 1984 and mid-February 1985 to a nominal depth of 2500 m. Of these floats, 4 from the first deployment and 2 from the second functioned properly. Float signals were recorded by four autonomous listening stations at a depth of 1900 m. These preliminary results show the tracks of floats up to July 1986 and represent 3600 float days of information. The main task of the experiment was to especially study the dispersion of radioactive substances

En teoretisk utdyping av rom og materialitet som pedagogisk ressurs i barnehagen

Directory of Open Access Journals (Sweden)

Solveig Nordtømme

2015-07-01

Full Text Available Abstract: This article is a theoretical exploration with the aim of discussing an ontological basis for space and materiality as educational resources in kindergarten. Attention is directed on children’s play experiences interacting with space and materiality, and how children use and create space. The metaphors front stage, space in between, and backstage (inspired from Erving Goffman, 1969, which form the study's main findings, are used as the backdrop for the issue and analyzes. The empirical material used in this exploration has been collected with an ethnographic methodological approach in two kindergartens. Maurice Merleau-Ponty’s (1962 focus on bodily experience and presence in space, along with concepts from Latour’s (2005 actor-network theory, is used to explore the data. The article contributes with theoretical tools for professionals in kindergarten teaching, to shed light on the importance of space, materiality and play in children's everyday life in kindergarten.Sammendrag: Denne artikkelen diskuterer et ontologisk grunnlag og er en teoretisk utforskning av rom og materialitet som en pedagogisk ressurs i barnehagen. Oppmerksomheten er rettet mot barns lekeerfaringer i samspill med rom og materialitet, og hvordan barn bruker og skaper rom. Metaforene hovedrom, mellomrom, og bakrom (inspirert fra Erving Goffman, 1969, som danner studiens hovedfunn, blir brukt som et bakteppe for problemstilling og analyser av det empiriske materialet fra to barnehager. Maurice Merleau-Ponty publikasjoner The Phenomenology of Perception (Merleau-Ponty, 1962 med sitt fokus på kroppslig erfaring i levd rom, blir brukt sammen med begreper fra Latours aktør-nettverksteori (Latour 2005 til å utforske hvordan rom og materialitet kan være pedagogiske ressurser. Artikkelens kunnskapsbidrag er å presentere et teoretisk verktøy for barnehageprofesjonen og kunnskaper om lekens betydning i barns hverdag i barnehagen.

The Virtual Man Project's CD-ROM "Voice Assessment: Speech-Language Pathology and Audiology & Medicine", Vol.1

Directory of Open Access Journals (Sweden)

Millena Maria Ramalho Matta Vieira

2009-01-01

Full Text Available The CD-ROM "Voice Assessment: Speech-Language Pathology and Audiology & Medicine" was developed as a teaching tool for people interested in the production of the spoken or sung human voice. Its content comprises several subjects concerning the anatomy and physiology of spoken and sung voice. A careful assessment becomes necessary in order to ensure the effectiveness of teaching and learning educational materials, whether related to education or health, within the proposal of education mediated by technology. OBJECTIVE: This study aimed to evaluate the efficacy of the Virtual Man Project's CD-ROM "Voice Assessment: Speech-Language Pathology and Audiology & Medicine", as a self-learning material, in two different populations: Speech-Language Pathology and Audiology students and Lyrical Singing students. The participants were instructed to study the CD-ROM during 1 month and answer two questionnaires: one before and another one after studying the CD-ROM. The quantitative results were compared statistically by the Student's t-test at a significance level of 5%. RESULTS: Seventeen out of the 28 students who completed the study, were Speech-Language Pathology and Audiology students, while 11 were Lyrical Singing students (dropout rate of 44%. Comparison of the answers to the questionnaires before and after studying the CD-ROM showed a statistically significant increase of the scores for the questionnaire applied after studying the CD-ROM for both Speech-Language Pathology and Audiology and Lyrical Singing students, with p<0.001 and p<0.004, respectively. There was also a statistically significant difference in all topics of this questionnaire for both groups of students. CONCLUSION: The results concerning the evaluation of the Speech-Language Pathology and Audiology and Lyrical Singing students' knowledge before and after learning from the CD-ROM allowed concluding that the participants made significant improvement in their knowledge of the proposed

Is there a role for rifampicin, ofloxacin and minocycline (ROM) therapy in the treatment of leprosy? Systematic review and meta-analysis.

Science.gov (United States)

Setia, Maninder S; Shinde, Santosh S; Jerajani, Hemangi R; Boivin, Jean-François

2011-12-01

A combination of rifampicin, ofloxacin and minocycline (ROM) is one of the newer recommendations for treatment of leprosy. We performed a systematic review and a meta-analysis of studies that had evaluated the efficacy of ROM therapy in treatment of paucibacillary and multibacillary leprosy patients. Studies were identified by searching the PubMed, Embase, LILACS and Cochrane databases. Data were abstracted from all relevant studies, and fixed effects models were used to calculate the summary estimate of effect in paucibacillary and multibacillary leprosy patients. Six studies comparing ROM therapy to multidrug therapy and eight studies that evaluated the effect of ROM therapy alone (no comparison group) were included in the review and meta-analysis. The combined estimate for single dose ROM vs. multidrug therapy in paucibacillary leprosy patients suggested that ROM was less effective than multidrug therapy in these patients [relative risk: 0.91, 95% confidence intervals (CI): 0.86-0.97]. However, the combined estimate for multiple doses of ROM vs. multidrug therapy in multibacillary leprosy patients suggested that ROM was as effective as multidrug therapy in reducing bacillary indices in these patients (proportion change: -4%, 95% CI -31% to 23%). No major side effects were reported in either the ROM or the multidrug treatment groups. Single-dose ROM therapy was less effective than multidrug therapy in paucibacillary patients. However, there are insufficient data to come to a valid conclusion on the efficacy of multidose ROM therapy in multibacillary leprosy, and additional studies with ROM therapy in multibacillary leprosy are needed. Furthermore, multiple doses may be considered as another alternative even for paucibacillary patients, and randomised controlled trials of this therapy may be useful to understand its contribution in the treatment and control of leprosy. © 2011 Blackwell Publishing Ltd.

Utilizing the Evaluation Process in CD-ROM Development.

Science.gov (United States)

Crews, Tena B.; Chalupa, Marilyn R.

1999-01-01

While a CD-ROM on network topologies was being developed, it was evaluated formatively by 14 office systems teachers and summatively by 23 students using it in class. Improvements in ease of use, performance, and the accuracy and clarity of content were made. (SK)

Validation of salinity data from ARGO floats: Comparison between the older ARGO floats and that of later deployments

Digital Repository Service at National Institute of Oceanography (India)

Youn, Y.-H.; Lee, H.; Chang, Y.-S.; Pankajakshan, T.

Continued observation of ARGO floats or years (about 4 years) makes the conductivity sensor more vulnerable to fouling by marine life and associated drift in salinity measurements. In this paper, we address this issue by making use of floats...

Calculation method of passive tracer using regional ocean modeling system (ROMS)

International Nuclear Information System (INIS)

Tubono, Takaki; Tsumune, Daisuke; Misumi, Kazuhiro; Yoshida, Yoshikatsu

2010-01-01

A dose assessments method for packages shipping radioactive materials was developed to calculate concentrations of radioactive materials discharged from the hypothetically sinking point using Regional Ocean Modeling System (ROMS). The programs of ROMS were improved for simultaneously calculating the flow fields around Japan and the concentrations discharged from several bottom points in the continental shelf. The model domain covered the northeast pacific region around Japan, 20degN-65degN, 120degE-165degE, with 1/10 degree horizontal resolution and 30 sigma-levels. The ROMS model captured main features such as Kuroshio currents, including the separation location and the Kuroshio extension, and Oyashio currents. The calculated volume transports through the main straits such as Tokara strait, Tsushima strait and Tsugaru strait were compared well to the measured or estimated that. The calculated concentrations discharged from 12 bottom points showed mixing associated with the eddies of ocean currents. This method is available to evaluate effectively the concentrations of radioactive materials only by setting the subsidence location and the concentrations and volume discharged. (author)

A radiation-tolerant, low-power non-volatile memory based on silicon nanocrystal quantum dots

OpenAIRE

Bell, L. D.; Boer, E.; Ostraat, M.; Brongersma, M. L.; Flagan, R. C.; Atwater, H. A.; De Blauwe, J.; Green, M. L.

2001-01-01

Nanocrystal nonvolatile floating-gate memories are a good candidate for space applications - initial results suggest they are fast, more reliable and consume less power than conventional floating gate memories. In the nanocrystal based NVM device, charge is not stored on a continuous polysilicon layer (so-called floating gate), but instead on a layer of discrete nanocrystals. Charge injection and storage in dense arrays of silicon nanocrystals in SiO_2 is a critical aspect of the performance ...

Public census data on CD-ROM at Lawrence Berkeley Laboratory

Energy Technology Data Exchange (ETDEWEB)

Merrill, D.W.

1993-01-16

The Comprehensive Epidemiologic Data Resource (CEDR) and Populations at Risk to Environmental Pollution (PAREP) projects, of the Information and Computing Sciences Division (ICSD) at Lawrence Berkeley Laboratory (LBL), are using public socioeconomic and geographic data files which are available to CEDR and PAREP collaborators via LBL's computing network. At this time 72 CD-ROM diskettes (approximately 37 gigabytes) are on line via the Unix file server cedrcd.lbl.gov''. Most of the files are from the US Bureau of the Census, and many of these pertain to the 1990 Census of Population and Housing. All the CD-ROM diskettes contain documentation in the form of ASCII text files. In addition, printed documentation for most files is available for inspection at University of California Data and Technical Assistance (UC DATA), tel. (510) 642-6571, or the UC Documents Library, tel. (510) 642-2569, both located on the UC Berkeley Campus. Many of the CD-ROM diskettes distributed by the Census Bureau contain software for PC compatible computers, for easily accessing the data. Shared access to the data is maintained through a collaboration among the CEDR and PAREP projects at LBL, and UC DATA, and the UC Documents Library. LBL is grateful to UC DATA and the UC Documents Library for the use of their CD-ROM diskettes. Shared access to LBL facilities may be restricted in the future if costs become prohibitive. Via the Sun Network File System (NFS), these data can be exported to Internet computers for direct access by the user's application program(s). Due to the size of the files, this access method is preferred over File Transfer Protocol (FTP) access. Please contact Deane Merrill (dwmerrill lbl.gov) if you wish to make use of the data.

Large floating structures technological advances

CERN Document Server

Wang, BT

2015-01-01

This book surveys key projects that have seen the construction of large floating structures or have attained detailed conceptual designs. This compilation of key floating structures in a single volume captures the innovative features that mark the technological advances made in this field of engineering, and will provide a useful reference for ideas, analysis, design, and construction of these unique and emerging urban projects to offshore and marine engineers, urban planners, architects and students.

CD roms and multimedia projector as complimentary educational ...

African Journals Online (AJOL)

This paper examines the potentials of utilizing Compact Disk Read Only Memory (CD-ROM) and the multimedia projector as complimentary educational technology for teaching music in colleges of education in Nigeria. While recognizing the problem of ineffective methods of teaching in Nigeria's educational system, the ...

Influence of different types of low substituted hydroxypropyl cellulose on tableting, disintegration, and floating behaviour of floating drug delivery systems.

Science.gov (United States)

Diós, Péter; Pernecker, Tivadar; Nagy, Sándor; Pál, Szilárd; Dévay, Attila

2015-11-01

The object of the present study is to evaluate the effect of application of low-substituted hydroxypropyl cellulose (L-HPC) 11 and B1 as excipients promoting floating in gastroretentive tablets. Directly compressed tablets were formed based on experimental design. Face-centred central composite design was applied with two factors and 3 levels, where amount of sodium alginate (X 1) and L-HPC (X2 ) were the numerical factors. Applied types of L-HPCs and their 1:1 mixture were included in a categorical factor (X 3). Studied parameters were floating lag time, floating time, floating force, swelling behaviour of tablets and dissolution of paracetamol, which was used as a model active substance. Due to their physical character, L-HPCs had different water uptake and flowability. Lower flowability and lower water uptake was observed after 60 min at L-HPC 11 compared to L-HPC B1. Shorter floating times were detected at L-HPC 11 and L-HPC mixtures with 0.5% content of sodium alginate, whereas alginate was the only significant factor. Evaluating results of drug release and swelling studies on floating tablets revealed correlation, which can serve to help to understand the mechanism of action of L-HPCs in the field development of gastroretentive dosage forms.

Floating on the margins [Environmental issues for floating production platforms

International Nuclear Information System (INIS)

Grimshaw, R.

1997-01-01

The main environmental issues challenging oilfield development using floating production platforms in harsh environments such as the Atlantic frontier are discussed. These fall into two broad categories -operating conditions and biological disturbance. Particular combinations of wind and currents can lead to extremely difficult operating conditions through which floating units are expected to maintain production for economic reasons. This imposes stringent conditions on the design and construction of tanker hulls and of risers to enable them to remain connected at all times. Prediction of wind and wave forces is a crucial element of operational and safety planning. Fauna in seabed sediments disturbed by pipeline laying often relocate but some seeding back of colonies may be required in hard rock areas. Migration routes for cetaceans and the feeding grounds of marine birds must be considered and the potential long and short term damage to commercial fisheries through discharges need to be assessed. A significant risk is the interaction of sub-sea facilities and fishing gear and oil spills. Operational and accidental discharges of production chemicals, produced water containing oil, deck drainage and treated sewage, and discharges to air from flaring and utility exhausts are of major environmental concern calling for mitigation and protection measures and contingency plans. Some of the environmental issues associated with decommissioning are reduced by the use of floating platforms but there are global and national regulations governing the process. (UK)

Public census data on CD-ROM at Lawrence Berkeley Laboratory

Energy Technology Data Exchange (ETDEWEB)

Merrill, D.W.

1992-10-01

The Comprehensive Epidemiologic Data Resource (CEDR) and Populations at Risk to Environmental Pollution (PAREP) projects, of the Information and Computing Sciences Division (ICSD) at Lawrence Berkeley Laboratory (LBL), are using public socio-economic and geographic data files which are available to CEDR and PAREP collaborators via LBL's computing network. At this time 70 CD-ROM diskettes (approximately 36 gigabytes) are on line via the Unix file server cedrcd. lbl. gov. Most of the files are from the US Bureau of the Census, and most pertain to the 1990 Census of Population and Housing. All the CD-ROM diskettes contain documentation in the form of ASCII text files. Printed documentation for most files is available for inspection at University of California Data and Technical Assistance (UC DATA), or the UC Documents Library. Many of the CD-ROM diskettes distributed by the Census Bureau contain software for PC compatible computers, for easily accessing the data. Shared access to the data is maintained through a collaboration among the CEDR and PAREP projects at LBL, and UC DATA, and the UC Documents Library. Via the Sun Network File System (NFS), these data can be exported to Internet computers for direct access by the user's application program(s).

Public census data on CD-ROM at Lawrence Berkeley Laboratory

Energy Technology Data Exchange (ETDEWEB)

Merrill, D.W.

1992-10-01

The Comprehensive Epidemiologic Data Resource (CEDR) and Populations at Risk to Environmental Pollution (PAREP) projects, of the Information and Computing Sciences Division (ICSD) at Lawrence Berkeley Laboratory (LBL), are using public socio-economic and geographic data files which are available to CEDR and PAREP collaborators via LBL`s computing network. At this time 70 CD-ROM diskettes (approximately 36 gigabytes) are on line via the Unix file server cedrcd. lbl. gov. Most of the files are from the US Bureau of the Census, and most pertain to the 1990 Census of Population and Housing. All the CD-ROM diskettes contain documentation in the form of ASCII text files. Printed documentation for most files is available for inspection at University of California Data and Technical Assistance (UC DATA), or the UC Documents Library. Many of the CD-ROM diskettes distributed by the Census Bureau contain software for PC compatible computers, for easily accessing the data. Shared access to the data is maintained through a collaboration among the CEDR and PAREP projects at LBL, and UC DATA, and the UC Documents Library. Via the Sun Network File System (NFS), these data can be exported to Internet computers for direct access by the user`s application program(s).

Effects of Using Human Patient Simulator (HPS versus a CD-ROM on Cognition and Critical Thinking

Directory of Open Access Journals (Sweden)

Don Johnson, PhD

2008-01-01

Full Text Available Background: Very little prospective randomized experimental research exists on the use of simulation as a teaching method, and no studies have compared the two strategies of using the HPS and a CD-ROM. In addition, no researchers have investigated the effects of simulation on various levels of cognition, specifically lower-level and higher-level cognition or critical thinking.Objectives: A prospective pretest-posttest experimental mixed design (within and between was used to determine if there were statistically significant differences in HPS and CD-ROM educational strategies in lower-level, higher-level cognition and critical thinking.Results: A repeated measures multivariate analysis of variance (RMANOVA with LSD post-hoc tests were used to analyze the data. There were no significant differences between the HPS and CD-ROM groups on lower-level cognition scores. The HPS group did significantly better than the CD-ROM group on higher-level cognition and critical thinking scores.Conclusion: This study demonstrated that the choice of teaching strategies for lower-level cognition does not make a statistically significant difference in outcome. However, the HPS is superior to using CD-ROM and should be considered as the choice in teaching.

The Application of a Modified d-ROMs Test for Measurement of Oxidative Stress and Oxidized High-Density Lipoprotein

Directory of Open Access Journals (Sweden)

Fumiaki Ito

2017-02-01

Full Text Available Reactive oxygen species (ROS are involved in the initiation and progression of atherosclerosis. ROS-derived hydroperoxides, as an indicator of ROS production, have been measured by using the diacron reactive oxygen metabolites (d-ROMs test, which requires iron-containing transferrin in the reaction mixture. In this study we developed a modified d-ROMs test, termed the Fe-ROMs test, where iron ions were exogenously added to the reaction mixture. This modification is expected to exclude the assay variation that comes from different blood iron levels in individuals. In addition, this Fe-ROMs test was helpful for determining the class of plasma lipoproteins that are hydroperoxidized. Low-density lipoprotein/very low-density lipoprotein (LDL/VLDL and high-density lipoprotein (HDL were purified by use of an LDL/VLDL purification kit and the dextran sulfate-Mg2+ precipitation method, respectively; their hydroperoxide contents were assessed by performing the Fe-ROMs test. The majority of the hydroperoxides were detected only in the HDL fraction, not in the LDL/VLDL. Further detailed analysis of HDLs by size-exclusion high-performance liquid chromatography revealed that the hydroperoxide-containing molecules were small-sized HDLs. Because HDL was shown to be the principal vehicle for the plasma hydroperoxides, this Fe-ROMs test is a beneficial method for the assessment of oxidized-HDL levels. Indeed, Fe-ROMs levels were strongly associated with the levels of oxidized HDL, which were determined by performing the malondialdehyde-modified HDL enzyme immunoassay. In conclusion, the Fe-ROMs test using plasma itself or the HDL fraction after dextran sulfate-Mg2+ precipitation is useful to assess the functionality of HDL, because the oxidation of HDL impairs its antiatherogenic capacity.

Conserving Earth's Biodiversity. [CD-ROM and] Instructor's Manual.

Science.gov (United States)

2000

This CD-ROM is designed as an interactive learning tool to support teaching in highly interdisciplinary fields such as conservation of biodiversity. Topics introduced in the software include the impact of humans on natural landscapes, threats to biodiversity, methods and theories of conservation biology, environmental laws, and relevant economic…

Investigation of Tank 241-AW-104 Composite Floating Layer

Energy Technology Data Exchange (ETDEWEB)

Meznarich, H. K. [Washington River Protection Solutions LLC (WRPS), Richland, WA (United States); Bolling, S. D. [Washington River Protection Solutions LLC (WRPS), Richland, WA (United States); Lachut, J. S. [Washington River Protection Solutions LLC (WRPS), Richland, WA (United States); Cooke, G. A. [Washington River Protection Solutions LLC (WRPS), Richland, WA (United States)

2018-02-27

Seven grab samples and one field blank were taken from Tank 241-AW-104 (AW-104) on June 2, 2017, and received at 222-S Laboratory on June 5, 2017. A visible layer with brown solids was observed floating on the top of two surface tank waste samples (4AW-17-02 and 4AW 17 02DUP). The floating layer from both samples was collected, composited, and submitted for chemical analyses and solid phase characterization in order to understand the composition of the floating layer. Tributyl phosphate and tridecane were higher in the floating layer than in the aqueous phase. Density in the floating layer was slightly lower than the mean density of all grab samples. Sodium nitrate and sodium carbonate were major components with a trace of gibbsite and very small size agglomerates were present in the solids of the floating layer. The supernate consisted of organics, soluble salt, and particulates.

A high performance gate drive for large gate turn off thyristors

Energy Technology Data Exchange (ETDEWEB)

Szilagyi, C.P.

1993-01-01

Past approaches to gate turn-off (GTO) gating are application oriented, inefficient and dissipate power even when inactive. They allow the gate to avalanch, and do not reduce GTO turn-on and turn-off losses. A new approach is proposed which will allow modular construction and adaptability to large GTOs in the 50 amp to 2000 amp range. The proposed gate driver can be used in large voltage source and current source inverters and other power converters. The approach consists of a power metal-oxide-silicon field effect transistor (MOSFET) technology gating unit, with associated logic and supervisory circuits and an isolated flyback converter as the dc power source for the gating unit. The gate driver formed by the gating unit and the flyback converter is designed for 4000 V isolation. Control and supervisory signals are exchanged between the gate driver and the remote control system via fiber optics. The gating unit has programmable front-porch current amplitude and pulse-width, programmable closed-loop controlled back-porch current, and a turn-off switch capable of supplying negative gate current at demand as a function of peak controllable forward anode current. The GTO turn-on, turn-off and gate avalanch losses are reduced to a minimum. The gate driver itself has minimum operating losses. Analysis, design and practical realization are reported. 19 refs., 54 figs., 1 tab.

Floating venous thrombi: diagnosis with spiral-CT-venography

International Nuclear Information System (INIS)

Gartenschlaeger, M.; Schmidt, J.A.

1996-01-01

Local application of contrast agent into an ipsilateral dorsal foot vein and spiral CT were used to examine 16 consecutive cases with deep venous thrombosis proven at conventional venography; in addition, colour Doppler flow imaging was performed. At conventional venography, 8/16 thrombi appeared to be floating and the remaining 8/16 were adherent to the vessel wall. Spiral-CT showed 15/16 thrombi to be adherent to the vessel wall; the floating thrombus correlated with findings in conventional venography. At colour Doppler flow imaging 3/16 thrombi were considered floating, one of them was discordant to conventional venography. The comparison of conventional venography to spiral-CT demonstrates complete agreement for adherence to vessel wall seen in conventional venography (p=1,0) and significant discordance in cases with free-floating appearance in conventional venography. Adherence of thrombi to the wall of the vessel at conventional venography is in agreement with computed tomography. Conventional venography probably overestimates the prevalence of free floating thrombi. (orig./MG) [de

Cd-Rom and Access to Information

OpenAIRE

Chacón Alvarado, Lucía

2011-01-01

The scientific and technological advances in the world and its application in different areas of knowledge have developed a new electronic age.Computers and telecommunications have created a new scenario for libraries and information centers leading to further changes in the use of its collections and its services increased. Libraries and information centers must address these changes because users demand access to information quickly and efficiently.The CD-ROM is a new technology that has be...

Herbal carrier-based floating microparticles of diltiazem ...

African Journals Online (AJOL)

Purpose: To formulate and characterize a gastroretentive floating drug delivery system for diltiazem hydrochloride using psyllium husk and sodium alginate as natural herbal carriers to improve the therapeutic effect of the drug in cardiac patients. Methods: Floating microparticles containing diltiazem hydrochloride were ...

Cholecystosonographic findings of clonorchiasis: Floating echogenic foci

Energy Technology Data Exchange (ETDEWEB)

Kim, Ho Kyun [Choong Joo X-ray Clinic, Choongjoo (Korea, Republic of)

1989-06-15

Author analysed cholecystosonographic findings in 22 patients with clonorchiasis, suspected prospectively by ultrasound and proved subsequently by demonstration of eggs in the stools. Fifteen gallbladders had nonshadowing, fusiform, discrete echogenic foci measuring 3{approx}6 mm in the lumen. Among these, the echogenic foci floated spontaneously in three cases, while in twelve cases they floated by position change or a light blow by the transducer. In the rest of the seven gallbladders, the echogenic foci were at the dependent portion. In the in vitro study with a worm suspension in saline in a surgical glove, the same echogenic foci as those seen in the gallbladders were demonstrated. The echogenic foci were precipitated in the dependent portion but float with a light blow on the glove. Author conclude that the floating echogenic foci in the lumen of the gallbladder are due to adult worms of clonorchis sinensis.

Cholecystosonographic findings of clonorchiasis: Floating echogenic foci

International Nuclear Information System (INIS)

Kim, Ho Kyun

1989-01-01

Author analysed cholecystosonographic findings in 22 patients with clonorchiasis, suspected prospectively by ultrasound and proved subsequently by demonstration of eggs in the stools. Fifteen gallbladders had nonshadowing, fusiform, discrete echogenic foci measuring 3∼6 mm in the lumen. Among these, the echogenic foci floated spontaneously in three cases, while in twelve cases they floated by position change or a light blow by the transducer. In the rest of the seven gallbladders, the echogenic foci were at the dependent portion. In the in vitro study with a worm suspension in saline in a surgical glove, the same echogenic foci as those seen in the gallbladders were demonstrated. The echogenic foci were precipitated in the dependent portion but float with a light blow on the glove. Author conclude that the floating echogenic foci in the lumen of the gallbladder are due to adult worms of clonorchis sinensis

Adolescencia, relaciones románticas y actividad sexual: una revisión

OpenAIRE

Vargas Trujillo, Elvia; Barrera, Fernando

2008-01-01

Se presenta una revisión de algunas de las investigaciones más recientes sobre la adolescencia y los factores asociados a las relaciones románticas y la actividad sexual durante la adolescencia. Se parte de la premisa de que el análisis de la iniciación romántica y sexual durante la adolescencia requiere de modelos de causalidad múltiple que permitan dar cuenta, conjuntamente, de los factores que se encuentran en los contextos individual, familiar y social asociados con estos dos procesos. Se...

Sensitivity analysis of floating offshore wind farms

International Nuclear Information System (INIS)

Castro-Santos, Laura; Diaz-Casas, Vicente

2015-01-01

Highlights: • Develop a sensitivity analysis of a floating offshore wind farm. • Influence on the life-cycle costs involved in a floating offshore wind farm. • Influence on IRR, NPV, pay-back period, LCOE and cost of power. • Important variables: distance, wind resource, electric tariff, etc. • It helps to investors to take decisions in the future. - Abstract: The future of offshore wind energy will be in deep waters. In this context, the main objective of the present paper is to develop a sensitivity analysis of a floating offshore wind farm. It will show how much the output variables can vary when the input variables are changing. For this purpose two different scenarios will be taken into account: the life-cycle costs involved in a floating offshore wind farm (cost of conception and definition, cost of design and development, cost of manufacturing, cost of installation, cost of exploitation and cost of dismantling) and the most important economic indexes in terms of economic feasibility of a floating offshore wind farm (internal rate of return, net present value, discounted pay-back period, levelized cost of energy and cost of power). Results indicate that the most important variables in economic terms are the number of wind turbines and the distance from farm to shore in the costs’ scenario, and the wind scale parameter and the electric tariff for the economic indexes. This study will help investors to take into account these variables in the development of floating offshore wind farms in the future

OCONUS Compliance Assessment Protocols - Qatar (Army Version) (CD-ROM)

National Research Council Canada - National Science Library

Krooks, David A

2004-01-01

...: 1 CD-ROM; 4 3/4 in.; 578 KB. ABSTRACT: This environmental compliance assessment manual is based on the Final Governing Standards for Environmental Security of United States Forces in the State of Qatar, 21 May 1999, and the Overseas...

Qualitative evaluation of a colorectal cancer education CD-ROM for Community Health Aides/practitioners in Alaska.

Science.gov (United States)

Cueva, Melany; Dignan, Mark; Lanier, Anne; Kuhnley, Regina

2014-12-01

Colorectal cancer (CRC) is an important contributor to the cancer burden among Alaska Native people. CRC is the leading incident cancer and the second leading cause of cancer mortality among Alaska Native people. Completing recommended CRC screening procedures has the potential to reduce both CRC incidence and mortality. "Taking Action Colorectal Health," a multidimensional audiovisual, interactive CD-ROM, incorporates adult education learning principles to provide Alaska's Community Health Aides/Practitioners with timely, medically accurate, and culturally relevant CRC place-based education. Providing this resource on CD-ROM empowers learning within communities and places where people live or choose to learn. The dynamic process of developing, implementing, and evaluating this CRC CD-ROM was informed by a sociocultural approach to share health messages. Within this approach, cultural values, beliefs, and behaviors are affirmed as a place of wisdom and resilience and built upon to provide context and meaning for health messaging. Alaska Native values that honor family, relationships, the land, storytelling, and humor were included in CD-ROM content. Between January and May 2012, 20 interviews were conducted with individuals who had used the CD-ROM. Four categorical themes emerged from analysis of interview transcripts: likeability, utilization, helpfulness, and behavior change. As a result of self-paced learning through stories, movies, and interactive games, respondents reported healthy behavior changes they were making for themselves, with their families and in their patient care practices. This CD-ROM is a culturally based practical course that increased knowledge and activities around colorectal cancer screening by Community Health Aides/Practitioners in Alaska.

A novel optical gating method for laser gated imaging

Science.gov (United States)

Ginat, Ran; Schneider, Ron; Zohar, Eyal; Nesher, Ofer

2013-06-01

For the past 15 years, Elbit Systems is developing time-resolved active laser-gated imaging (LGI) systems for various applications. Traditional LGI systems are based on high sensitive gated sensors, synchronized to pulsed laser sources. Elbit propriety multi-pulse per frame method, which is being implemented in LGI systems, improves significantly the imaging quality. A significant characteristic of the LGI is its ability to penetrate a disturbing media, such as rain, haze and some fog types. Current LGI systems are based on image intensifier (II) sensors, limiting the system in spectral response, image quality, reliability and cost. A novel propriety optical gating module was developed in Elbit, untying the dependency of LGI system on II. The optical gating module is not bounded to the radiance wavelength and positioned between the system optics and the sensor. This optical gating method supports the use of conventional solid state sensors. By selecting the appropriate solid state sensor, the new LGI systems can operate at any desired wavelength. In this paper we present the new gating method characteristics, performance and its advantages over the II gating method. The use of the gated imaging systems is described in a variety of applications, including results from latest field experiments.

The Market Place: An Internal View of the Future of CD-ROM--The Perspective of the H. W. Wilson Company.

Science.gov (United States)

Miller, Frank W.; Loeding, Deborah Voigt

1989-01-01

Discussion of technological developments in library reference services focuses on contributions of the H. W. Wilson Company and highlights CD-ROM technology. Topics discussed include online access; menu-driven systems; CD-ROM hardware and software concerns; user response to CD-ROM; quality control of databases; pricing considerations; and future…

A Look at Dialog's First CD-ROM Product.

Science.gov (United States)

Duggan, Mary Kay

1987-01-01

Discusses reasons for selecting ERIC with the Dialog OnDisc software for training information professionals in online searching at the University of California, Berkeley, and analyzes some of the features of the CD-ROM software. Pros and cons of online and OnDisc access are summarized, and three references are listed. (Author/MES)

CD ROM 'Natural heritage of Slovakia'

International Nuclear Information System (INIS)

Uradnikova, B.

2005-01-01

Centre of Environmental Education Geopark ('Centre') applied environmental education into school and out-of-school institutions. The 'Centre' is working in the fields: environmental education, eco-tourism development, presentation of the cultural landscape and world heritage. The CD ROM 'Natural heritage of Slovakia' was created with aim enhancement of environmental awareness, pedagogy, education and development of eco-tourism on the Slovakia. It abets general review about environment, its components, legislative, history and the present day of nature and landscape protection

Potential of water surface-floating microalgae for biodiesel production: Floating-biomass and lipid productivities.

Science.gov (United States)

Muto, Masaki; Nojima, Daisuke; Yue, Liang; Kanehara, Hideyuki; Naruse, Hideaki; Ujiro, Asuka; Yoshino, Tomoko; Matsunaga, Tadashi; Tanaka, Tsuyoshi

2017-03-01

Microalgae have been accepted as a promising feedstock for biodiesel production owing to their capability of converting solar energy into lipids through photosynthesis. However, the high capital and operating costs, and high energy consumption, are hampering commercialization of microalgal biodiesel. In this study, the surface-floating microalga, strain AVFF007 (tentatively identified as Botryosphaerella sudetica), which naturally forms a biofilm on surfaces, was characterized for use in biodiesel production. The biofilm could be conveniently harvested from the surface of the water by adsorbing onto a polyethylene film. The lipid productivity of strain AVFF007 was 46.3 mg/L/day, allowing direct comparison to lipid productivities of other microalgal species. The moisture content of the surface-floating biomass was 86.0 ± 1.2%, which was much lower than that of the biomass harvested using centrifugation. These results reveal the potential of this surface-floating microalgal species as a biodiesel producer, employing a novel biomass harvesting and dewatering strategy. Copyright © 2016 The Society for Biotechnology, Japan. Published by Elsevier B.V. All rights reserved.

Floating seal system for rotary devices

Science.gov (United States)

Banasiuk, H.A.

1983-08-23

This invention relates to a floating seal system for rotary devices to reduce gas leakage around the rotary device in a duct and across the face of the rotary device to an adjacent duct. The peripheral seal bodies are made of resilient material having a generally U-shaped cross section wherein one of the legs is secured to a support member and the other of the legs forms a contacting seal against the rotary device. The legs of the peripheral seal form an extended angle of intersection of about 10[degree] to about 30[degree] in the unloaded condition to provide even sealing forces around the periphery of the rotary device. The peripheral seal extends around the periphery of the support member except where intersected by radial seals which reduce gas leakage across the face of the rotary device and between adjacent duct portions. The radial seal assembly is fabricated from channel bars, the smaller channel bar being secured to the divider of the support member and a larger inverted rigid floating channel bar having its legs freely movable over the legs of the smaller channel bar forming therewith a tubular channel. A resilient flexible tube is positioned within the tubular channel for substantially its full length to reduce gas leakage across the tubular channel. A spacer extends beyond the face of the floating channel near each end of the floating channel a distance to provide desired clearance between the floating channel and the face of the rotary device. 5 figs.

An Asynchronous IEEE Floating-Point Arithmetic Unit

Directory of Open Access Journals (Sweden)

Joel R. Noche

2007-12-01

Full Text Available An asynchronous floating-point arithmetic unit is designed and tested at the transistor level usingCadence software. It uses CMOS (complementary metal oxide semiconductor and DCVS (differentialcascode voltage switch logic in a 0.35 µm process using a 3.3 V supply voltage, with dual-rail data andsingle-rail control signals using four-phase handshaking.Using 17,085 transistors, the unit handles single-precision (32-bit addition/subtraction, multiplication,division, and remainder using the IEEE 754-1985 Standard for Binary Floating-Point Arithmetic, withrounding and other operations to be handled by separate hardware or software. Division and remainderare done using a restoring subtractive algorithm; multiplication uses an additive algorithm. Exceptionsare noted by flags (and not trap handlers and the output is in single-precision.Previous work on asynchronous floating-point arithmetic units have mostly focused on single operationssuch as division. This is the first work to the authors' knowledge that can perform floating-point addition,multiplication, division, and remainder using a common datapath.

Lab Manual & Resources for Materials Science, Engineering and Technology on CD-Rom

Science.gov (United States)

Jacobs, James A.; McKenney, Alfred E.

2001-01-01

The National Educators' Workshop (NEW:Update) series of workshops has been in existence since 1986. These annual workshops focus on technical updates and laboratory experiments for materials science, engineering and technology, involving new and traditional content in the field. Scores of educators and industrial and national laboratory personnel have contributed many useful experiments and demonstrations which were then published as NASA Conference Proceedings. This "out poring of riches" creates an ever-expanding shelf of valuable teaching tools for college, university, community college and advanced high school instruction. Now, more than 400 experiments and demonstrations, representing the first thirteen years of NEW:Updates have been selected and published on a CD-ROM, through the collaboration of this national network of materials educators, engineers, and scientists. The CD-ROM examined in this document utilizes the popular Adobe Acrobat Reader format and operates on most popular computer platforms. This presentation provides an overview of the second edition of Experiments in Materials Science, Engineering and Technology (EMSET2) CD-ROM, ISBN 0-13-030534-0.

Dynamic gating window for compensation of baseline shift in respiratory-gated radiation therapy

International Nuclear Information System (INIS)

Pepin, Eric W.; Wu Huanmei; Shirato, Hiroki

2011-01-01

Purpose: To analyze and evaluate the necessity and use of dynamic gating techniques for compensation of baseline shift during respiratory-gated radiation therapy of lung tumors. Methods: Motion tracking data from 30 lung tumors over 592 treatment fractions were analyzed for baseline shift. The finite state model (FSM) was used to identify the end-of-exhale (EOE) breathing phase throughout each treatment fraction. Using duty cycle as an evaluation metric, several methods of end-of-exhale dynamic gating were compared: An a posteriori ideal gating window, a predictive trend-line-based gating window, and a predictive weighted point-based gating window. These methods were evaluated for each of several gating window types: Superior/inferior (SI) gating, anterior/posterior beam, lateral beam, and 3D gating. Results: In the absence of dynamic gating techniques, SI gating gave a 39.6% duty cycle. The ideal SI gating window yielded a 41.5% duty cycle. The weight-based method of dynamic SI gating yielded a duty cycle of 36.2%. The trend-line-based method yielded a duty cycle of 34.0%. Conclusions: Dynamic gating was not broadly beneficial due to a breakdown of the FSM's ability to identify the EOE phase. When the EOE phase was well defined, dynamic gating showed an improvement over static-window gating.

Regional Ocean Modeling System (ROMS): Main Hawaiian Islands: Data Assimilating

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — Regional Ocean Modeling System (ROMS) 3-day, 3-hourly data assimilating hindcast for the region surrounding the main Hawaiian islands at approximately 4-km...

Isolated photosystem I reaction centers on a functionalized gated high electron mobility transistor.

Science.gov (United States)

Eliza, Sazia A; Lee, Ida; Tulip, Fahmida S; Mostafa, Salwa; Greenbaum, Elias; Ericson, M Nance; Islam, Syed K

2011-09-01

In oxygenic plants, photons are captured with high quantum efficiency by two specialized reaction centers (RC) called Photosystem I (PS I) and Photosystem II (PS II). The captured photon triggers rapid charge separation and the photon energy is converted into an electrostatic potential across the nanometer-scale (~6 nm) reaction centers. The exogenous photovoltages from a single PS I RC have been previously measured using the technique of Kelvin force probe microscopy (KFM). However, biomolecular photovoltaic applications require two-terminal devices. This paper presents for the first time, a micro-device for detection and characterization of isolated PS I RCs. The device is based on an AlGaN/GaN high electron mobility transistor (HEMT) structure. AlGaN/GaN HEMTs show high current throughputs and greater sensitivity to surface charges compared to other field-effect devices. PS I complexes immobilized on the floating gate of AlGaN/GaN HEMTs resulted in significant changes in the device characteristics under illumination. An analytical model has been developed to estimate the RCs of a major orientation on the functionalized gate surface of the HEMTs. © 2011 IEEE

Isolated Photosystem I Reaction Centers on a Functionalized Gated High Electron Mobility Transistor

Energy Technology Data Exchange (ETDEWEB)

Eliza, Sazia A. [University of Tennessee, Knoxville (UTK); Lee, Ida [ORNL; Tulip, Fahmida S [ORNL; Islam, Syed K [University of Tennessee, Knoxville (UTK); Mostafa, Salwa [University of Tennessee, Knoxville (UTK); Greenbaum, Elias [ORNL; Ericson, Milton Nance [ORNL

2011-01-01

In oxygenic plants, photons are captured with high quantum efficiency by two specialized reaction centers (RC) called Photosystem I (PS I) and Photosystem II (PS II). The captured photon triggers rapid charge separation and the photon energy is converted into an electrostatic potential across the nanometer-scale nm reaction centers. The exogenous photovoltages from a single PS I RC have been previously measured using the technique of Kelvin force probe microscopy (KFM). However, biomolecular photovoltaic applications require two-terminal devices. This paper presents for the first time, a micro-device for detection and characterization of isolated PS I RCs. The device is based on an AlGaN/GaN high electron mobility transistor (HEMT) structure. AlGaN/GaN HEMTs show high current throughputs and greater sensitivity to surface charges compared to other field-effect devices. PS I complexes immobilized on the floating gate of AlGaN/GaN HEMTs resulted in significant changes in the device characteristics under illumination. An analytical model has been developed to estimate the RCs of a major orientation on the functionalized gate surface of the HEMTs.

Aerodynamics and Motion Performance of the H-Type Floating Vertical Axis Wind Turbine

Directory of Open Access Journals (Sweden)

Ying Guo

2018-02-01

Full Text Available Aerodynamics and motion performance of the floating vertical wind turbine (VAWT were studied in this paper, where the wind turbine was H-type and the floating foundation was truss spar type. Based on the double-multiple-stream-tube theory, the formulae were deduced to calculate the aerodynamic loads acting on the wind turbine considering the motions of the floating foundation. The surge-heave-pitch nonlinear coupling equations of the H-type floating VAWT were established. Aerodynamics and motion performance of a 5 MW H-type floating VAWT was studied, and the effect of the floating foundation motions on the aerodynamic loads was analyzed. It is shown that the motions of the floating foundation on the aerodynamics cannot be ignored. The motion of the H-type floating VAWT was also compared with that of the Φ-type floating VAWT: they have the same floating foundation, rated output power, mooring system and total displacement. The results show that the H-type floating VAWT has better motion performance, and the mean values of surge, heave and pitch of the H-type floating VAWT are much smaller comparing with the Φ-type floating VAWT.

Position control of a floating nuclear power plant

International Nuclear Information System (INIS)

Motohashi, K.; Hamamoto, T.; Sasaki, R.; Kojima, M.

1993-01-01

In spite of the increasing demand of electricity in Japan, the sites of nuclear power plants suitable for conventional seismic regulations become severely limited. Under these circumstances, several types of advanced siting technology have been developed. Among them, floating power plants have a great advantage of seismic isolation that leads to the seismic design standardization and factory fabrication. The feasibility studies or preliminary designs of floating power plants enclosed by breakwaters in the shallow sea have been carried out last two decades in U.S. and Japan. On the other hand, there are few investigations on the dynamic behavior of floating power plants in the deep sea. The offshore floating nuclear power plants have an additional advantage in that large breakwaters are not required, although the safety checking is inevitable against wind-induced waves. The tension-leg platforms which have been constructed for oil drilling in the deep sea seem to be a promising offshore siting technology of nuclear power plants. The tension-leg mooring system can considerably restrain the heave and pitch of a floating power plant because of significant stiffness in the vertical direction. Different from seismic effects, wind-induced waves may be predicted in advance by making use of ocean weather forecasts using artificial satellites. According to the wave prediction, the position of the floating plant may be controlled by adjusting the water content in ballast tanks and the length of tension-legs before the expected load arrives. The position control system can reduce the wave force acting on the plant and to avoid the unfavorable response behavior of the plant. In this study a semi-submerged circular cylinder with tension-legs is considered as a mathematical model. The configuration of circular cylinder is effective because the dynamic behavior does not depend on incident wave directions. It is also unique in that it can obtain the closed-form solution of

Tidal simulation using regional ocean modeling systems (ROMS)

Science.gov (United States)

Wang, Xiaochun; Chao, Yi; Li, Zhijin; Dong, Changming; Farrara, John; McWilliams, James C.; Shum, C. K.; Wang, Yu; Matsumoto, Koji; Rosenfeld, Leslie K.;

The Writing Process for "Edutaining" CD-ROM Adventures.

Science.gov (United States)

Mountain, Lee

2000-01-01

Describes a CD-ROM adventure story written by the author to educate her students about the word relationships of synonyms and antonyms. Discusses how this interactive medium put a different twist on each of the stages of the writing process itself. Relates how two students enthusiastically used the program, and were inspired to write one of their…

Land and Marine Gravity Data on CD-ROM - 1999 Edition

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — The Land and Marine Gravity 1999 Edition 2-volume CD-ROM set contains observed and derived land and marine gravity data contributed by many national and...

Significance of measuring oxidative stress in lifestyle-related diseases from the viewpoint of correlation between d-ROMs and BAP in Japanese subjects

International Nuclear Information System (INIS)

Fukui, Toshiki; Yamauchi, Kazuhiro; Maruyama, Mie; Yasuda, Tadashi; Abe, Youichi; Kohno, Masakazu

2011-01-01

In recent years, oxidative stress has been postulated to be an important factor in the pathogenesis and development of lifestyle-related diseases. In this study, we investigated the association between the derivatives of reactive oxygen metabolites (d-ROMs), as an index of products of reactive oxygen species (ROS), and biological antioxidant potential (BAP), as an index of antioxidant potential. We also investigated the associations between d-ROMs or BAP and the risk factors for lifestyle-related diseases or metabolic syndrome-associated factors to evaluate their usefulness in preventive medicine. There were 442 subjects who underwent health checkup examination in our facilities. In addition to standard medical checkup items, we analyzed d-ROMs, BAP, brachial-ankle pulse wave velocity, high-sensitivity C-reactive protein level and visceral fat area (VFA) visualized on a computed tomography scan. The mean d-ROM value in females was significantly higher than that in males. There was a positive correlation between the d-ROM and VFA levels. On correlation analysis, there was a negative correlation between the d-ROM and creatinine levels. As factors that influence d-ROMs, the level of VFA was selected, suggesting the significance of oxidative stress measurement with d-ROMs. In addition, there was a positive correlation between d-ROMs and BAP values. Further research is required to resolve whether increased production of ROS or the antioxidant potential that can compensate for such an increase of ROS is more important in vivo. (author)

Nanotechnology Aerospace Applications (Applications aerospatiales de la nanotechnologie) (CD-ROM)

National Research Council Canada - National Science Library

2007-01-01

...: 1 CD-ROM; 4 3/4 in.; 116 MB. ABSTRACT: The Educational Notes contain the abstracts and the lecture material of ten presentations, which provide a general introduction into nanotechnologies with selected topics, such as nanotechnology...

Alois Riegl, Die Entstehung der Barockkunst in Rom, 1908

NARCIS (Netherlands)

Witte, A.; Bacchi, A.; Barroero, L.

2017-01-01

In 1908, Alois Riegl's unfinished text on the Italian Baroque was published by Max Dvorak and Arthur Burda; they edited part of his notes for three consecutive series of lectures at Vienna University. Riegl's book title aply reads Entstehung der Barockkunst in Rom: Akademische Vorlesungen and deals

Floating arterial thrombus related stroke treated by intravenous thrombolysis.

Science.gov (United States)

Vanacker, P; Cordier, M; Janbieh, J; Federau, C; Michel, P

2014-01-01

The effects of intravenous thrombolysis on floating thrombi in cervical and intracranial arteries of acute ischemic stroke patients are unknown. Similarly, the best prevention methods of early recurrences remain controversial. This study aimed to describe the clinical and radiological outcome of thrombolyzed strokes with floating thrombi. We retrospectively analyzed all thrombolyzed stroke patients in our institution between 2003 and 2010 with floating thrombi on acute CT-angiography before the intravenous thrombolysis. The floating thrombus was diagnosed if an elongated thrombus of at least 5 mm length, completely surrounded by contrast on supra-aortic neck or intracerebral arteries, was present on CT-angiography. Demographics, vascular risk factors, and comorbidities were recorded and stroke etiology was determined after a standardized workup. Repeat arterial imaging was performed by CTA at 24 h or before if clinical worsening was noted and then by Doppler and MRA during the first week and at four months. Of 409 thrombolyzed stroke patients undergoing acute CT Angiography, seven (1.7%) had a floating thrombus; of these seven, six had it in the anterior circulation. Demographics, risk factors and stroke severity of these patients were comparable to the other thrombolyzed patients. After intravenous thrombolysis, the floating thrombi resolved completely at 24 h in four of the patients, whereas one had an early recurrent stroke and one developed progressive worsening. One patient developed early occlusion of the carotid artery with floating thrombus and subsequently a TIA. The two patients with a stable floating thrombus had no clinical recurrences. In the literature, only one of four reported cases were found to have a thrombolysis-related early recurrence. Long-term outcome seemed similar in thrombolyzed patients with floating thrombus, despite a possible increase of very early recurrence. It remains to be established whether acute mechanical thrombectomy could be

Can flexibility help you float?

Science.gov (United States)

Burton, L. J.; Bush, J. W. M.

2012-10-01

We consider the role of flexibility in the weight-bearing characteristics of bodies floating at an interface. Specifically, we develop a theoretical model for a two-dimensional thin floating plate that yields the maximum stable plate load and optimal stiffness for weight support. Plates small relative to the capillary length are primarily supported by surface tension, and their weight-bearing potential does not benefit from flexibility. Above a critical size comparable to the capillary length, flexibility assists interfacial flotation. For plates on the order of and larger than the capillary length, deflection from an initially flat shape increases the force resulting from hydrostatic pressure, allowing the plate to support a greater load. In this large plate limit, the shape that bears the most weight is a semicircle, which displaces the most fluid above the plate for a fixed plate length. Exact results for maximum weight-bearing plate shapes are compared to analytic approximations made in the limits of large and small plate sizes. The value of flexibility for floating to a number of biological organisms is discussed in light of our study.

Nanotechnology Aerospace Applications (Applications aerospatiales de la nanotechnologie) (CD-ROM)

National Research Council Canada - National Science Library

2005-01-01

...: 1 CD-ROM; 4 3/4 in.; 59.1 MB. ABSTRACT: The Educational Notes contain the abstracts and the lecture material of ten presentations, which provide a general introduction into nanotechnologies with selected topics, such as nanotechnology...

14 CFR 25.533 - Hull and main float bottom pressures.

Science.gov (United States)

2010-01-01

... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false Hull and main float bottom pressures. 25... AIRCRAFT AIRWORTHINESS STANDARDS: TRANSPORT CATEGORY AIRPLANES Structure Water Loads § 25.533 Hull and main float bottom pressures. (a) General. The hull and main float structure, including frames and bulkheads...

14 CFR 23.529 - Hull and main float landing conditions.

Science.gov (United States)

2010-01-01

... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false Hull and main float landing conditions. 23... Water Loads § 23.529 Hull and main float landing conditions. (a) Symmetrical step, bow, and stern... directed perpendicularly to the keel line. (b) Unsymmetrical landing for hull and single float seaplanes...

Management of CD-ROM Resources in Nigeria Academic Libraries ...

African Journals Online (AJOL)

The study is on management of CD-ROM resources in Nigerian academic libraries with reference to Federal Polytechnic Nekede Library, Owerri. A descriptive survey method was adopted random sampling technique was used in selecting twenty five (25) staff from the library under study. The questionnaire was the major ...

Stretching & Flexibility: An Interactive Encyclopedia of Stretching. [CD-ROM].

Science.gov (United States)

2002

This CD-ROM offers 140 different stretches in full-motion video sequences. It focuses on the proper techniques for overall physical fitness, injury prevention and rehabilitation, and 23 different sports (e.g., golf, running, soccer, skiing, climbing, football, and baseball). Topics include stretching for sports; stretching awareness and education…

Guide Structures in CD-ROM Dic- tionaries, with Specific Reference ...

African Journals Online (AJOL)

Not all the search options in CD-ROM dictionaries necessarily maintain the boundaries ... In this article all derivatives of lase are highlighted in the microstructure, ... searches frustrates the user and should be addressed in future editions of the.

Development and Evaluation of Floating Microspheres of Curcumin ...

African Journals Online (AJOL)

Purpose: To prepare and evaluate floating microspheres of curcumin for prolonged gastric residence time and increased drug bioavailability. Methods: Floating microsphere were prepared by emulsion solvent diffusion method, using hydroxylpropyl methylcellulose (HPMC), ethyl cellulose (EC), Eudragit S 100 polymer in ...

Vertical pump with free floating check valve

International Nuclear Information System (INIS)

Lindsay, M.

1980-01-01

A vertical pump is described which has a bottom discharge with a free floating check valve disposed in the outlet plenum thereof. The free floating check valve comprises a spherical member with a hemispherical cage-like member attached thereto which is capable of allowing forward or reverse flow under appropriate conditions while preventing reverse flow under inappropriate conditions

Development of floating strip micromegas detectors

Energy Technology Data Exchange (ETDEWEB)

Bortfeldt, Jonathan

2014-04-28

Micromegas are high-rate capable, high-resolution micro-pattern gaseous detectors. Square meter sized resistive strip Micromegas are foreseen as replacement of the currently used precision tracking detectors in the Small Wheel, which is part of the forward region of the ATLAS muon spectrometer. The replacement is necessary to ensure tracking and triggering performance of the muon spectrometer after the luminosity increase of the Large Hadron Collider beyond its design value of 10{sup 34} cm{sup -2}s{sup -1} around 2020. In this thesis a novel discharge tolerant floating strip Micromegas detector is presented and described. By individually powering copper anode strips, the effects of a discharge are confined to a small region of the detector. This reduces the impact of discharges on the efficiency by three orders of magnitude, compared to a standard Micromegas. The physics of the detector is studied and discussed in detail. Several detectors are developed: A 6.4 x 6.4 cm{sup 2} floating strip Micromegas with exchangeable SMD capacitors and resistors allows for an optimization of the floating strip principle. The discharge behavior is investigated on this device in depth. The microscopic structure of discharges is quantitatively explained by a detailed detector simulation. A 48 x 50 cm{sup 2} floating strip Micromegas is studied in high energy pion beams. Its homogeneity with respect to pulse height, efficiency and spatial resolution is investigated. The good performance in high-rate background environments is demonstrated in cosmic muon tracking measurements with a 6.4 x 6.4 cm{sup 2} floating strip Micromegas under lateral irradiation with 550 kHz 20 MeV proton beams. A floating strip Micromegas doublet with low material budget is developed for ion tracking without limitations from multiple scattering in imaging applications during medical ion therapy. Highly efficient tracking of 20 MeV protons at particle rates of 550 kHz is possible. The reconstruction of the

Development of floating strip micromegas detectors

International Nuclear Information System (INIS)

Bortfeldt, Jonathan

2014-01-01

Micromegas are high-rate capable, high-resolution micro-pattern gaseous detectors. Square meter sized resistive strip Micromegas are foreseen as replacement of the currently used precision tracking detectors in the Small Wheel, which is part of the forward region of the ATLAS muon spectrometer. The replacement is necessary to ensure tracking and triggering performance of the muon spectrometer after the luminosity increase of the Large Hadron Collider beyond its design value of 10 34 cm -2 s -1 around 2020. In this thesis a novel discharge tolerant floating strip Micromegas detector is presented and described. By individually powering copper anode strips, the effects of a discharge are confined to a small region of the detector. This reduces the impact of discharges on the efficiency by three orders of magnitude, compared to a standard Micromegas. The physics of the detector is studied and discussed in detail. Several detectors are developed: A 6.4 x 6.4 cm 2 floating strip Micromegas with exchangeable SMD capacitors and resistors allows for an optimization of the floating strip principle. The discharge behavior is investigated on this device in depth. The microscopic structure of discharges is quantitatively explained by a detailed detector simulation. A 48 x 50 cm 2 floating strip Micromegas is studied in high energy pion beams. Its homogeneity with respect to pulse height, efficiency and spatial resolution is investigated. The good performance in high-rate background environments is demonstrated in cosmic muon tracking measurements with a 6.4 x 6.4 cm 2 floating strip Micromegas under lateral irradiation with 550 kHz 20 MeV proton beams. A floating strip Micromegas doublet with low material budget is developed for ion tracking without limitations from multiple scattering in imaging applications during medical ion therapy. Highly efficient tracking of 20 MeV protons at particle rates of 550 kHz is possible. The reconstruction of the track inclination in a single

Public census data on CD-ROM at Lawrence Berkeley Laboratory. Revision 4

Energy Technology Data Exchange (ETDEWEB)

Merrill, D.W.

1993-03-12

The Comprehensive Epidemiologic Data Resource (CEDR) and Populations at Risk to Environmental Pollution (PAREP) projects, of the Information and Computing sciences Division (ICSD) at Lawrence Berkeley Laboratory (LBL), are using public socioeconomic and geographic data files which are available to CEDR and PAREP collaborators via LBL`s computing network. At this time 89 CD-ROM diskettes (approximately 45 gigabytes) are on line via the Unix file server cedrcd.lbl.gov. Most of the files are from the US Bureau of the Census, and many of these pertain to the 1990 Census of Population and Housing. All the CD-ROM diskettes contain documentation in the form of ASCII text files. In addition, printed documentation for most files is available for inspection at University of California Data and Technical Assistance (UC DATA), tel. (510) 642-6571, or the UC Documents Library, tel. (510) 642-2569, both located on the UC Berkeley Campus. Many of the CD-ROM diskettes distributed by the Census Bureau contain software for PC compatible computers, for easily accessing the data. Shared access to the data is maintained through a collaboration among the CEDR and PAREP projects at LBL, and UC DATA, and the UC Documents Library. LBL is grateful to UC DATA and the UC Documents Library for the use of their CD-ROM diskettes. Shared access to LBL facilities may be restricted in the future if costs become prohibitive. Via the Sun Network File System (NFS), these data can be exported to Internet computers for direct access by the user`s application program(s). Due to the size of the files, this access method is preferred over File Transfer Protocol (FTP) access.

Floating barrier

Energy Technology Data Exchange (ETDEWEB)

1968-05-06

This floating barrier consists of relatively long elements which can be connected to form a practically continuous assembly. Each element consists of an inflatable tube with an apron of certain height, made of impregnated fabric which is resistant to ocean water and also to hydrocarbons. Means for connecting one element to the following one, and means for attaching ballast to the apron are also provided.

Micromechanisms with floating pivot

Science.gov (United States)

Garcia, Ernest J.

2001-03-06

A new class of tilting micromechanical mechanisms have been developed. These new mechanisms use floating pivot structures to relieve some of the problems encountered in the use of solid flexible pivots.

Effects of using simulation versus CD-ROM in the performance of ultrasound-guided regional anesthesia.

Science.gov (United States)

Gasko, John; Johnson, Arthur; Sherner, John; Craig, John; Gegel, Brian; Burgert, James; Sama, Samuel; Franzen, Thomas

2012-08-01

The purpose of this study was to determine which method of teaching, CD-ROM, simulation, or a combination of both, was more effective in increasing the performance of ultrasound-guided regional anesthesia. No studies have investigated these methods. The framework for this study was critical thinking. The study was a prospective, mixed (between and within) subjects, experimental design. The sample consisted of 29 student registered nurse anesthetists randomly assigned to 1 of 3 groups: CD-ROM (n = 11), simulation (n = 11), and combination (n = 7). All groups were evaluated by the use of cadavers before and 2 months after the intervention using a valid and reliable instrument of performance. A repeated-measures analysis of variance indicated that the combination was significantly better than the CD-ROM and simulation (P teaching ultrasound-guided regional anesthesia techniques.

New insights on poly(vinyl acetate)-based coated floating tablets: characterisation of hydration and CO2 generation by benchtop MRI and its relation to drug release and floating strength.

Science.gov (United States)

Strübing, Sandra; Abboud, Tâmara; Contri, Renata Vidor; Metz, Hendrik; Mäder, Karsten

2008-06-01

The purpose of this study was to investigate the mechanism of floating and drug release behaviour of poly(vinyl acetate)-based floating tablets with membrane controlled drug delivery. Propranolol HCl containing tablets with Kollidon SR as an excipient for direct compression and different Kollicoat SR 30 D/Kollicoat IR coats varying from 10 to 20mg polymer/cm2 were investigated regarding drug release in 0.1N HCl. Furthermore, the onset of floating, the floating duration and the floating strength of the device were determined. In addition, benchtop MRI studies of selected samples were performed. Coated tablets with 10mg polymer/cm2 SR/IR, 8.5:1.5 coat exhibited the shortest lag times prior to drug release and floating onset, the fastest increase in and highest maximum values of floating strength. The drug release was delayed efficiently within a time interval of 24 h by showing linear drug release characteristics. Poly(vinyl acetate) proved to be an appropriate excipient to ensure safe and reliable drug release. Floating strength measurements offered the possibility to quantify the floating ability of the developed systems and thus to compare different formulations more efficiently. Benchtop MRI studies allowed a deeper insight into drug release and floating mechanisms noninvasively and continuously.

ROMS/TOMS Tangent Linear and Adjoint Models: Testing and Applications

National Research Council Canada - National Science Library

Miller, Arthur J; Cornuelle, Bruce D

2004-01-01

... (Regional Ocean Modeling System/Terrain-Following Ocean Modeling System) that is suitable for general use by the ROMS/TOMS community and to develop computational platforms based on the TLM and ADM for 4D variational data assimilation (4DVar...

Public census data on CD-ROM at Lawrence Berkeley Laboratory. Revision 1

Energy Technology Data Exchange (ETDEWEB)

Merrill, D.W.

1992-07-02

In connection with the Comprehensive Epidemiologic Data Resource (CEDR) and Populations at Risk to Environmental Pollution (PAREP) projects, of the Information and Computing Sciences Division (ICSD) at Lawrence Berkeley Laboratory (LBL), are using public socioeconomic and geographic data files which are available to CEDR and PAREP collaborators via LBL`s computing network. At this time 67 CD-ROM diskettes (approximately 35 gigabytes) are on line via the Unix file server cedrcd.lbl.gov. Most of the files are from the US Bureau of the Census, and most pertain to the 1990 Census of Population and Housing. This paper contains a list of the CD-ROMs available.

Pengaruh Frekuensi Melihat Iklan Floating terhadap Tingkat Kesadaran Merek

Directory of Open Access Journals (Sweden)

Forddhanto Bimantoro

2013-11-01

Full Text Available Abstract: Floating ad  is online advertisement aiming to stimulate brand awareness by increasing familiarity through reexposing advertisement. This research examines the influence of ARCO Depok members’ exposure of floating ad at www.detik.com to their brand awareness about Samsung LED TV. The frequency of consuming the advertisement is differentiated into three categories, namely three times, five times and never. The result shows that the respondents’ exposure of floating ad could influence the level of brand awareness as much as 40.7%. However, this tendency was not represented in the category of five times. The result also shows that the only control variable which was able to significantly influence the level of brand awareness was the variable of respondents’ visitation to the site of detik.com. Abstrak: Iklan floating merupakan iklan di media internet yang bertujuan mencapai kesadaran merek dengan cara meningkatkan familiarity melalui frekuensi pengulangan iklan. Frekuensi melihat iklan floating dibedakan  dengan memilah kelompok responden yang dikenai frekuensi melihat iklan 3 kali, 5 kali dan tidak melihat iklan. Penelitian ini menguji pengaruh frekuensi melihat iklan floating di www.detik.com terhadap tingkat kesadaran merek Samsung LED TV pada warga ARCO Depok, Jawa Barat. Hasil penelitian menunjukkan bahwa frekuensi melihat iklan floating dapat mempengaruhi tingkat kesadaran merek sebesar 40,7%; namun tidak terbukti pada kelompok yang melihat iklan sebanyak lima kali. Variabel kontrol yang mampu mempengaruhi tingkat kesadaran merek secara signifikan hanya variabel kunjungan responden ke detik.com.Â

Capture of free-floating planets by planetary systems

Science.gov (United States)

Goulinski, Nadav; Ribak, Erez N.

2018-01-01

Evidence of exoplanets with orbits that are misaligned with the spin of the host star may suggest that not all bound planets were born in the protoplanetary disc of their current planetary system. Observations have shown that free-floating Jupiter-mass objects can exceed the number of stars in our Galaxy, implying that capture scenarios may not be so rare. To address this issue, we construct a three-dimensional simulation of a three-body scattering between a free-floating planet and a star accompanied by a Jupiter-mass bound planet. We distinguish between three different possible scattering outcomes, where the free-floating planet may get weakly captured after the brief interaction with the binary, remain unbound or 'kick out' the bound planet and replace it. The simulation was performed for different masses of the free-floating planets and stars, as well as different impact parameters, inclination angles and approach velocities. The outcome statistics are used to construct an analytical approximation of the cross-section for capturing a free-floating planet by fitting their dependence on the tested variables. The analytically approximated cross-section is used to predict the capture rate for these kinds of objects, and to estimate that about 1 per cent of all stars are expected to experience a temporary capture of a free-floating planet during their lifetime. Finally, we propose additional physical processes that may increase the capture statistics and whose contribution should be considered in future simulations in order to determine the fate of the temporarily captured planets.

Numerical study on aerodynamic damping of floating vertical axis wind turbines

Science.gov (United States)

Cheng, Zhengshun; Aagaard Madsen, Helge; Gao, Zhen; Moan, Torgeir

2016-09-01

Harvesting offshore wind energy resources using floating vertical axis wind turbines (VAWTs) has attracted an increasing interest in recent years. Due to its potential impact on fatigue damage, the aerodynamic damping should be considered in the preliminary design of a floating VAWT based on the frequency domain method. However, currently the study on aerodynamic damping of floating VAWTs is very limited. Due to the essential difference in aerodynamic load characteristics, the aerodynamic damping of a floating VAWT could be different from that of a floating horizontal axis wind turbine (HAWT). In this study, the aerodynamic damping of floating VAWTs was studied in a fully coupled manner, and its influential factors and its effects on the motions, especially the pitch motion, were demonstrated. Three straight-bladed floating VAWTs with identical solidity and with a blade number varying from two to four were considered. The aerodynamic damping under steady and turbulent wind conditions were estimated using fully coupled aero-hydro-servo-elastic time domain simulations. It is found that the aerodynamic damping ratio of the considered floating VAWTs ranges from 1.8% to 5.3%. Moreover, the aerodynamic damping is almost independent of the rotor azimuth angle, and is to some extent sensitive to the blade number.

Numerical study on aerodynamic damping of floating vertical axis wind turbines

DEFF Research Database (Denmark)

Cheng, Zhengshun; Aagaard Madsen, Helge; Gao, Zhen

2016-01-01

Harvesting offshore wind energy resources using floating vertical axis wind turbines (VAWTs) has attracted an increasing interest in recent years. Due to its potential impact on fatigue damage, the aerodynamic damping should be considered in the preliminary design of a floating VAWT based...... on the frequency domain method. However, currently the study on aerodynamic damping of floating VAWTs is very limited. Due to the essential difference in aerodynamic load characteristics, the aerodynamic damping of a floating VAWT could be different from that of a floating horizontal axis wind turbine (HAWT...... to four were considered. The aerodynamic damping under steady and turbulent wind conditions were estimated using fully coupled aero-hydro-servo-elastic time domain simulations. It is found that the aerodynamic damping ratio of the considered floating VAWTs ranges from 1.8% to 5.3%. Moreover...

A review on design and study of floating plant mooring systems

International Nuclear Information System (INIS)

Nakamura, Hideharu; Kashima, Ryoichi; Hagiwara, Yutaka; Matsuura, Shinichi; Shiojiri, Hiroo

1985-01-01

There exists a widespread anticipation among nuclear power engineers that a floating nuclear power plant (NPP) may have a couple of advantages over other types; such as seismic isolation, standardizations of design and manufacturing etc. However, it also seems that a number of problems still remain to be clarified to adopt the floating NPP in Japan. One of them is magnitude of external forces acting on floating structure, which depend on mooring system. The purpose of the present report is to survey various kinds of mooring systems, structural analyses and design criteria, and examples of the same scale floating structures taking into consideration of the floating NPP which displaces 300,000 Ton, and furthermore, to discuss the future problems in regard to the mooring system still to be investigated before the floating plants can be constructed. (author)

14 CFR 23.533 - Hull and main float bottom pressures.

Science.gov (United States)

2010-01-01

... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false Hull and main float bottom pressures. 23... Water Loads § 23.533 Hull and main float bottom pressures. (a) General. The hull and main float....00213; K2=hull station weighing factor, in accordance with figure 2 of appendix I of this part; VS1...

Quantifying the Impact of Single Bit Flips on Floating Point Arithmetic

Energy Technology Data Exchange (ETDEWEB)

Elliott, James J [ORNL; Mueller, Frank [North Carolina State University; Stoyanov, Miroslav K [ORNL; Webster, Clayton G [ORNL

2013-08-01

In high-end computing, the collective surface area, smaller fabrication sizes, and increasing density of components have led to an increase in the number of observed bit flips. If mechanisms are not in place to detect them, such flips produce silent errors, i.e. the code returns a result that deviates from the desired solution by more than the allowed tolerance and the discrepancy cannot be distinguished from the standard numerical error associated with the algorithm. These phenomena are believed to occur more frequently in DRAM, but logic gates, arithmetic units, and other circuits are also susceptible to bit flips. Previous work has focused on algorithmic techniques for detecting and correcting bit flips in specific data structures, however, they suffer from lack of generality and often times cannot be implemented in heterogeneous computing environment. Our work takes a novel approach to this problem. We focus on quantifying the impact of a single bit flip on specific floating-point operations. We analyze the error induced by flipping specific bits in the most widely used IEEE floating-point representation in an architecture-agnostic manner, i.e., without requiring proprietary information such as bit flip rates and the vendor-specific circuit designs. We initially study dot products of vectors and demonstrate that not all bit flips create a large error and, more importantly, expected value of the relative magnitude of the error is very sensitive on the bit pattern of the binary representation of the exponent, which strongly depends on scaling. Our results are derived analytically and then verified experimentally with Monte Carlo sampling of random vectors. Furthermore, we consider the natural resilience properties of solvers based on the fixed point iteration and we demonstrate how the resilience of the Jacobi method for linear equations can be significantly improved by rescaling the associated matrix.

Multifractal analysis of managed and independent float exchange rates

Science.gov (United States)

Stošić, Darko; Stošić, Dusan; Stošić, Tatijana; Stanley, H. Eugene

2015-06-01

We investigate multifractal properties of daily price changes in currency rates using the multifractal detrended fluctuation analysis (MF-DFA). We analyze managed and independent floating currency rates in eight countries, and determine the changes in multifractal spectrum when transitioning between the two regimes. We find that after the transition from managed to independent float regime the changes in multifractal spectrum (position of maximum and width) indicate an increase in market efficiency. The observed changes are more pronounced for developed countries that have a well established trading market. After shuffling the series, we find that the multifractality is due to both probability density function and long term correlations for managed float regime, while for independent float regime multifractality is in most cases caused by broad probability density function.

WindFloat Pacific Project, Final Scientific and Technical Report

Energy Technology Data Exchange (ETDEWEB)

Banister, Kevin [Principle Power, Inc., Emeryville, CA (United States)

2017-01-17

PPI’s WindFloat Pacific project (WFP) was an up to 30 MW floating offshore wind demonstration project proposed off the Coast of Oregon. The project was to be sited approximately 18 miles due west of Coos Bay, in over 1000 ft. of water, and is the first floating offshore wind array proposed in the United States, and the first offshore wind project of any kind proposed off the West Coast. PPI’s WindFloat, a semi-submersible foundation designed for high-capacity (6MW+) offshore wind turbines, is at the heart of the proposed project, and enables access to the world class wind resource at the project site and, equally, to other deep water, high wind resource areas around the country.

The Correlation of Exercise and Range of Motion (ROM on Elderly Knee Observasional Study on Elderly People in Pedurungan Semarang

Directory of Open Access Journals (Sweden)

Adhitya Putra Widyantoro

2012-06-01

Design and Method: Observastional study with a cross sectional design 80 elderly men and women were divided into 2 groups: gymnastics group in the Social Rehabilitation Unit Of Pucang Gading (n=40 and unexcercises group in the Penggaron village (n=40. In both groups, the degree of ROM of knee was assessed using the Goniometer. To evaluate the value of its significance, the data were analyzed using the Mann Withney test followed by Spearmann’s rho test. Result: ROM for gymnastic(exercised group and unexercised group were 115.50°±11.591°, 95.38°±12.780° respectively with p<0. 001. Resuts showed that doing exercise was useful for maintaining ROM of knee in elderly people. Spearmann’s rho test resulted in a strong correlation between ROM and exercise with r value of 0.652. Conclusion: exercise correlates with ROM of knee in elderly (Sains Medika, 4(1:39-45.

Linear gate

International Nuclear Information System (INIS)

Suwono.

1978-01-01

A linear gate providing a variable gate duration from 0,40μsec to 4μsec was developed. The electronic circuity consists of a linear circuit and an enable circuit. The input signal can be either unipolar or bipolar. If the input signal is bipolar, the negative portion will be filtered. The operation of the linear gate is controlled by the application of a positive enable pulse. (author)

A novel grounded to floating admittance converter with electronic control

Science.gov (United States)

Prasad, Dinesh; Ahmad, Javed; Srivastava, Mayank

2018-01-01

This article suggests a new grounded to floating admittance convertor employing only two voltage differencing transconductance amplifiers (VDTAs). The proposed circuit can convert any arbitrary grounded admittance into floating admittance with electronically controllable scaling factor. The presented converter enjoys the following beneficial: (1) no requirement of any additional passive element (2) scaling factor can be tuned electronically through bias currents of VDTAs (3) no matching constraint required (4) low values of active/passive sensitivity indexes and (5) excellent non ideal behavior that indicates no deviation in circuit behavior even under non ideal environment. Application of the proposed configuration in realization of floating resistor and floating capacitor has been presented and the workability of these floating elements has been confirmed by active filter design examples. SPICE simulations have been performed to demonstrate the performance of the proposed circuits.

Managing nuclear knowledge: IAEA activities and international coordination. Including resource material full text CD-ROM

International Nuclear Information System (INIS)

2005-06-01

The present CD-ROM summarizes some activities carried out by the Departments of Nuclear Energy and Nuclear Safety and Security in the area of nuclear knowledge management in the period 2003-2005. It comprises, as open resource, most of the relevant documents in full text, including policy level documents, reports, presentation material by Member States and meeting summaries. The collection starts with a reprint of the report to the IAEA General Conference 2004 on Nuclear Knowledge [GOV/2004/56-GC(48)/12] summarizing the developments in nuclear knowledge management since the 47th session of the General Conference in 2003 and covers Managing Nuclear Knowledge including safety issues and Information and Strengthening Education and Training for Capacity Building. It contains an excerpt on Nuclear Knowledge from the General Conference Resolution [GC(48)/RES/13] on Strengthening the Agency's Activities Related to Nuclear Science, Technology and Applications. On the CD-ROM itself, all documents can easily be accessed by clicking on their titles on the subject pages (also printed at the end of this Working Material). Part 1 of the CD-ROM covers the activities in the period 2003-2005 and part 2 presents a resource material full text CD-ROM on Managing Nuclear Knowledge issued in October 2003

CD-ROM for the PGAA-IAEA database

International Nuclear Information System (INIS)

Firestone, R.B.; Zerking, V.

2007-01-01

Both the database of prompt gamma rays from slow neutron capture for elemental analysis and the results of this CRP are available on the accompanying CD-ROM. The file index.html is the home page for the CD-ROM, and provides links to the following information: (a) The CRP - General information, papers and reports relevant to this CRP. (b) The PGAA-IAEA database viewer - An interactive program to display and search the PGAA database by isotope, energy or capture cross-section. (c) The Database of Prompt Gamma Rays from Slow Neutron Capture for Elemental Analysis - This report. (d) The PGAA database files - Adopted PGAA database and associated files in EXCEL, PDF and Text formats. The archival databases by Lone et al. and by Reedy and Frankle are also available. (e) The Evaluated Gamma-Ray Activation File (EGAF) - The adopted PGAA database in ENSDF format. Data can be viewed with the Isotope Explorer 2.2 ENSDF Viewer. (f) The PGAA database evaluation - ENSDF format versions of the adopted PGAA database, and the Budapest and ENSDF isotopic input files. Decay scheme balance and statistical analysis summaries are provided. (g) The Isotope Explorer 2.2 ENSDF viewer - Windows software for viewing the level scheme drawings and tables provided in ENSDF format. The complete ENSDF database is included, as of December 2002. The databases and viewers are discussed in greater detail in the following sections

Operating Experience with Nuclear Power Stations in Member States. 2016 Edition (CD-ROM)

International Nuclear Information System (INIS)

2016-06-01

This CD-ROM contains the 47th edition of the IAEA’s series of annual reports on operating experience with nuclear power plants in Member States. It is a direct output from the IAEA’s Power Reactor Information System (PRIS) and contains information on electricity production and overall performance of individual plants during 2015. In addition to annual information, the report contains a historical summary of performance during the lifetime of individual plants and figures illustrating worldwide performance of the nuclear industry. The CD-ROM contains also an overview of design characteristics and dashboards of all operating nuclear power plants worldwide

Public census data on CD-ROM at Lawrence Berkeley Laboratory. Revision 3

Energy Technology Data Exchange (ETDEWEB)

Merrill, D.W.

1993-01-16

The Comprehensive Epidemiologic Data Resource (CEDR) and Populations at Risk to Environmental Pollution (PAREP) projects, of the Information and Computing Sciences Division (ICSD) at Lawrence Berkeley Laboratory (LBL), are using public socioeconomic and geographic data files which are available to CEDR and PAREP collaborators via LBL`s computing network. At this time 72 CD-ROM diskettes (approximately 37 gigabytes) are on line via the Unix file server ``cedrcd.lbl.gov``. Most of the files are from the US Bureau of the Census, and many of these pertain to the 1990 Census of Population and Housing. All the CD-ROM diskettes contain documentation in the form of ASCII text files. In addition, printed documentation for most files is available for inspection at University of California Data and Technical Assistance (UC DATA), tel. (510) 642-6571, or the UC Documents Library, tel. (510) 642-2569, both located on the UC Berkeley Campus. Many of the CD-ROM diskettes distributed by the Census Bureau contain software for PC compatible computers, for easily accessing the data. Shared access to the data is maintained through a collaboration among the CEDR and PAREP projects at LBL, and UC DATA, and the UC Documents Library. LBL is grateful to UC DATA and the UC Documents Library for the use of their CD-ROM diskettes. Shared access to LBL facilities may be restricted in the future if costs become prohibitive. Via the Sun Network File System (NFS), these data can be exported to Internet computers for direct access by the user`s application program(s). Due to the size of the files, this access method is preferred over File Transfer Protocol (FTP) access. Please contact Deane Merrill (dwmerrill@lbl.gov) if you wish to make use of the data.

New gate opening hours

CERN Multimedia

GS Department

2009-01-01

Please note the new opening hours of the gates as well as the intersites tunnel from the 19 May 2009: GATE A 7h - 19h GATE B 24h/24 GATE C 7h - 9h\t17h - 19h GATE D 8h - 12h\t13h - 16h GATE E 7h - 9h\t17h - 19h Prévessin 24h/24 The intersites tunnel will be opened from 7h30 to 18h non stop. GS-SEM Group Infrastructure and General Services Department

Development and Utilization of Regional Oceanic Modeling System (ROMS). Delicacy, Imprecision, and Uncertainty of Oceanic Simulations: An Investigation with the Regional Oceanic Modeling System (ROMS). Mixing in the Ocean Surface Layer Using the Regional Oceanic Modeling System (ROMS).

Science.gov (United States)

2011-09-30

community use for ROMS is biogeochemisty: chemical cycles, water quality, blooms , micro-nutrients, larval dispersal, biome transitions, and coupling to...J.C. McWilliams, X. Capet, and J. Kurian, 2010: Heat balance and eddies in the Peru- Chile Current System. Climate Dynamics, 37, in press. doi10.1007

ISAC's Gating-ML 2.0 data exchange standard for gating description.

Science.gov (United States)

Spidlen, Josef; Moore, Wayne; Brinkman, Ryan R

2015-07-01

The lack of software interoperability with respect to gating has traditionally been a bottleneck preventing the use of multiple analytical tools and reproducibility of flow cytometry data analysis by independent parties. To address this issue, ISAC developed Gating-ML, a computer file format to encode and interchange gates. Gating-ML 1.5 was adopted and published as an ISAC Candidate Recommendation in 2008. Feedback during the probationary period from implementors, including major commercial software companies, instrument vendors, and the wider community, has led to a streamlined Gating-ML 2.0. Gating-ML has been significantly simplified and therefore easier to support by software tools. To aid developers, free, open source reference implementations, compliance tests, and detailed examples are provided to stimulate further commercial adoption. ISAC has approved Gating-ML as a standard ready for deployment in the public domain and encourages its support within the community as it is at a mature stage of development having undergone extensive review and testing, under both theoretical and practical conditions. © 2015 International Society for Advancement of Cytometry.

Determination of prospective displacement-based gate threshold for respiratory-gated radiation delivery from retrospective phase-based gate threshold selected at 4D CT simulation

International Nuclear Information System (INIS)

Vedam, S.; Archambault, L.; Starkschall, G.; Mohan, R.; Beddar, S.

2007-01-01

Four-dimensional (4D) computed tomography (CT) imaging has found increasing importance in the localization of tumor and surrounding normal structures throughout the respiratory cycle. Based on such tumor motion information, it is possible to identify the appropriate phase interval for respiratory gated treatment planning and delivery. Such a gating phase interval is determined retrospectively based on tumor motion from internal tumor displacement. However, respiratory-gated treatment is delivered prospectively based on motion determined predominantly from an external monitor. Therefore, the simulation gate threshold determined from the retrospective phase interval selected for gating at 4D CT simulation may not correspond to the delivery gate threshold that is determined from the prospective external monitor displacement at treatment delivery. The purpose of the present work is to establish a relationship between the thresholds for respiratory gating determined at CT simulation and treatment delivery, respectively. One hundred fifty external respiratory motion traces, from 90 patients, with and without audio-visual biofeedback, are analyzed. Two respiratory phase intervals, 40%-60% and 30%-70%, are chosen for respiratory gating from the 4D CT-derived tumor motion trajectory. From residual tumor displacements within each such gating phase interval, a simulation gate threshold is defined based on (a) the average and (b) the maximum respiratory displacement within the phase interval. The duty cycle for prospective gated delivery is estimated from the proportion of external monitor displacement data points within both the selected phase interval and the simulation gate threshold. The delivery gate threshold is then determined iteratively to match the above determined duty cycle. The magnitude of the difference between such gate thresholds determined at simulation and treatment delivery is quantified in each case. Phantom motion tests yielded coincidence of simulation

Biblioteca Naţională a României: obiective şi perspective în valorificarea patrimoniului cultural

Directory of Open Access Journals (Sweden)

Elena Tîrziman

2008-01-01

Biblioteca Naţională a României este implicată în proiecte internaţionale care au ca scop crearea de conţinut digital relevant pentru memoria culturală europeană: The European Library – TEL (Biblioteca europeană, Manuscriptorium şi ENRICH – European Networking Resources and Information concerning Cultural Heritage, proiecte coordonate de Biblioteca Naţională a Cehiei. Biblioteca Naţională a României a contribuit la proiectele Manuscriptorium / ENRICH prin carte românească veche din perioada corespunzătoare secolelor XVI-XVII.

Floating Inductance and FDNR Using Positive Polarity Current Conveyors

Directory of Open Access Journals (Sweden)

K. Pal

2004-01-01

Full Text Available A generalized circuit based on five positive polarity second-generation current conveyors is introduced. The circuit simulates a floating inductance, capacitor floatation circuit and floating fdnr. All these circuits use grounded capacitors.

Sabrewing: A lightweight architecture for combined floating-point and integer arithmetic

NARCIS (Netherlands)

Bruintjes, Tom; Walters, K.H.G.; Gerez, Sabih H.; Molenkamp, Egbert; Smit, Gerardus Johannes Maria

In spite of the fact that floating-point arithmetic is costly in terms of silicon area, the joint design of hardware for floating-point and integer arithmetic is seldom considered. While components like multipliers and adders can potentially be shared, floating-point and integer units in

Reservoir and civil engineering geophysics (CD-Rom); Geophysique de gisement et de genie civil (CD-Rom)

Energy Technology Data Exchange (ETDEWEB)

Mari, J.L.; Chapellier, D.

1999-07-01

This CD-Rom is a pedagogical tool developed from the book 'field and civil engineering geophysics' (Technip ed., 1998). It presents the geophysical methods (surface and well geophysical surveys, radar surveys and well logging) and their application in the study of oil fields and also in civil engineering. Several cartoons illustrate the principle of methods, their domain of use and their limitations. It covers the following topics: surface seismic surveys (waves propagation, equipments, reflexion and refraction seismic surveys, surface waves); well seismic surveys (operation, data processing, imaging); well logging (acoustic, nuclear,electrical and others, methods of interpretation); radar surveys (principle, surface, wells, possibilities and limitations). (J.S.)

Production of floating pellets using appropriate methods | Suleiman ...

African Journals Online (AJOL)

The study investigated into the use of floating materials like candle wax, yeast and baking powder to achieve pellet buoyancy. Ten diets were formulated with incorporation of floating agents; Diet I-YBCT- (yeast-baking powder in cold water -toasted), Diet II-YBCU- (yeast-baking powder in cold water -untoasted) Diet III ...

Towards Interactive Steering of a Very Large Floating Structure Code by Using HPC Parallelisation Strategies

KAUST Repository

Frisch, Jerome; Gao, Ruiping; Mundani, Ralf-Peter; Wang, Chien Ming; Rank, Ernst

2012-01-01

Very large floating structures (VLFSs) have been used for broad applications such as floating storage facilities, floating piers, floating bridges, floating airports, entertainment facilities, even habitation, and other purposes. Owing to its small

[Treatment of Persistent Somatoform Pain Disorder by Floating Needle Therapy and Duloxetine].

Science.gov (United States)

Ren, Wan-wen; Zhou, Zhi-ying; Xu, Mi-mi; Long, Sen; Tang, Guang-zheng; Mao, Hong-jing; Chen, Shu-lin

2016-02-01

To evaluate clinical effect and safety of floating needle therapy and duloxetine in treating patients with persistent somatoform pain disorder (PSPD). Totally 108 PSPD patients were randomly assigned to the floating needle treatment group, the duloxetine treatment group, and the placebo treatment group, 36 in each group. Patients in the floating needle treatment group received floating needle therapy and placebo. Those in the duloxetine treatment group received duloxetine and simulated floating needle therapy. Those in the placebo treatment group received the placebo and simulated floating needle therapy. All treatment lasted for six weeks. Efficacy and adverse reactions were evaluated using Simple McGill pain scale (SF-MPQ) and Treatment Emergent Symptom Scale (TESS) before treatment and immediately after treatment, as well as at the end of 1st, 2nd, 4th, and 6th week of treatment, respectively. Hamilton Depression Scale (HAMD, 17 items), Hamilton Anxiety Scale (HAMA) were assessed before treatment and at the end of 1st, 2nd, 4th, and 6th week of treatment, respectively. Patients in the floating needle treatment group and the duloxetine treatment group with the total reducing score rate of SF-MPQ in Pain Rating index (PRI) ≥ 50% after 6 weeks' treatment were involved in the follow-up study. (1) Compared with the same group before treatment, SF-MPQ score, HAMD score and HAMA total scores all decreased in all the three groups at the end of 1st, 2nd, 4th, and 6th week of treatment (P floating needle treatment group (P floating needle treatment group significantly decreased after 1, 2, 4, and 6 weeks of treatment (P floating needle treatment group, 17 (50.0%) in the duloxetine treatment group, and 7 (21.2%) in the placebo treatment group. Compared with the placebo treatment group, the incidence of adverse reaction increased in the duloxetine treatment group (χ² = 6.04, P floating needle treatment group (χ² = 14.9, P floating needle treatment group and 17

Development and Characterization of Novel Floating-Mucoadhesive Tablets Bearing Venlafaxine Hydrochloride

Directory of Open Access Journals (Sweden)

Raghvendra Misra

2016-01-01

Full Text Available The present investigation is concerned about the development of floating bioadhesive drug delivery system of venlafaxine hydrochloride which after oral administration exhibits a unique combination of floating and bioadhesion to prolong gastric residence time and increase drug bioavailability within the stomach. The floating bioadhesive tablets were prepared by the wet granulation method using different ratios of hydroxypropyl methyl cellulose (HPMC K4MCR and Carbopol 934PNF as polymers. Sodium bicarbonate (NaHCO3 and citric acid were used as gas (CO2 generating agents. Tablets were characterized for floating properties, in vitro drug release, detachment force, and swelling index. The concentration of hydroxypropyl methyl cellulose and Carbopol 934PNF significantly affects the in vitro drug release, floating properties, detachment force, and swelling properties of the tablets. The optimized formulation showed the floating lag time 72±2.49 seconds and duration of floating 24.50±0.74 hr. The in vitro release studies and floating behavior were studied in simulated gastric fluid (SGF at pH 1.2. Different drug release kinetics models were also applied. The in vitro drug release from tablets was sufficiently sustained (more than 18 hr and the Fickian transports of the drug from the tablets were confirmed. The radiological evidence suggests that the tablets remained buoyant and altered position in the stomach of albino rabbit and mean gastric residence time was prolonged (more than > 6 hr.

Formulation, release characteristics, and bioavailability study of gastroretentive floating matrix tablet and floating raft system of Mebeverine HCl.

Science.gov (United States)

El Nabarawi, Mohamed A; Teaima, Mahmoud H; Abd El-Monem, Rehab A; El Nabarawy, Nagla A; Gaber, Dalia A

2017-01-01

To prolong the residence time of dosage forms within the gastrointestinal tract until all drug is released at the desired rate is one of the real challenges for oral controlled-release drug delivery systems. This study was designed to develop a controlled-release floating matrix tablet and floating raft system of Mebeverine HCl (MbH) and evaluate different excipients for their floating behavior and in vitro controlled-release profiles. Oral pharmacokinetics of the optimum matrix tablet, raft system formula, and marketed Duspatalin ® 200 mg retard as reference were studied in beagle dogs. The optimized tablet formula (FT-10) and raft system formula (FRS-11) were found to float within 34±5 sec and 15±7 sec, respectively, and both remain buoyant over a period of 12 h in simulated gastric fluid. FT-10 (Compritol/HPMC K100M 1:1) showed the slowest drug release among all prepared tablet formulations, releasing about 80.2% of MbH over 8 h. In contrast, FRS-11 (Sodium alginate 3%/HPMC K100M 1%/Precirol 2%) had the greatest retardation, providing sustained release of 82.1% within 8 h. Compared with the marketed MbH product, the C max of FT-10 was almost the same, while FRS-11 maximum concentration was higher. The t max was 3.33, 2.167, and 3.0 h for marketed MbH product, FT-10, and FRS-11, respectively. In addition, the oral bioavailability experiment showed that the relative bioavailability of the MbH was 104.76 and 116.01% after oral administration of FT-10 and FRS-11, respectively, compared to marketed product. These results demonstrated that both controlled-released floating matrix tablet and raft system would be promising gastroretentive delivery systems for prolonging drug action.

OCONUS Compliance Assessment Protocols (OCAP) - Saudi Arabia (Army Version) (CD-ROM)

National Research Council Canada - National Science Library

Krooks, David A; Schell, Donna J

2004-01-01

...: 1 CD-ROM; 4 3/4 in.; 670 KB. ABSTRACT: This environmental compliance assessment manual is based on the Final Governing Standards for Environmental Security by United States Forces in the Kingdom of Saudi Arabia (FGS-SA...

Floating cultivation of marine cyanobacteria using coal fly ash

Energy Technology Data Exchange (ETDEWEB)

Matsumoto, M.; Yoshida, E.; Takeyama, H.; Matsunaga, T. [Tokyo University of Agriculture and Technology, Tokyo (Japan). Dept. of Biotetechnology

2000-07-01

The aim was to develop improved methodologies for bulk culturing of biotechnologically useful marine cyanobacteria in the open ocean. The viability of using coal fly ash (CFA) blocks as the support medium in a novel floating culture system for marine microalgae was investigated. The marine cyanobacterium Synechococcus sp. NKBC 040607 was found to adhere to floating CFA blocks in liquid culture medium. The marine cyanobacterium Synechococcus sp. NKBG 042902 weakly adhered to floating CFA blocks in BG-11 medium. Increasing the concentration of calcium ion in the culture medium enhanced adherence to CFA blocks.

Radiation-hardened bulk Si-gate CMOS microprocessor family

International Nuclear Information System (INIS)

Stricker, R.E.; Dingwall, A.G.F.; Cohen, S.; Adams, J.R.; Slemmer, W.C.

1979-01-01

RCA and Sandia Laboratories jointly developed a radiation-hardened bulk Si-gate CMOS technology which is used to fabricate the CDP-1800 series microprocessor family. Total dose hardness of 1 x 10 6 rads (Si) and transient upset hardness of 5 x 10 8 rads (Si)/sec with no latch up at any transient level was achieved. Radiation-hardened parts manufactured to date include the CDP-1802 microprocessor, the CDP-1834 ROM, the CDP-1852 8-bit I/O port, the CDP-1856 N-bit 1 of 8 decoder, and the TCC-244 256 x 4 Static RAM. The paper is divided into three parts. In the first section, the basic fundamentals of the non-hardened C 2 L technology used for the CDP-1800 series microprocessor parts is discussed along with the primary reasons for hardening this technology. The second section discusses the major changes in the fabrication sequence that are required to produce radiation-hardened devices. The final section details the electrical performance characteristics of the hardened devices as well as the effects of radiation on device performance. Also included in this section is a discussion of the TCC-244 256 x 4 Static RAM designed jointly by RCA and Sandia Laboratories for this application

Free-Floating Iris Cyst in a Patient with Recurrent Iritis

Directory of Open Access Journals (Sweden)

Joanne M.Y. Teong

2015-06-01

Full Text Available Purpose: We describe an unusual clinical finding of a free-floating iris cyst in a patient with recurrent iritis. Method: The clinical finding of a free-floating iris cyst was recorded using slit-lamp photography. Results: A 39-year-old male with a 5-year history of recurrent right iritis was found to have a small mobile iris cyst within his right anterior chamber, first identified 3 years ago. The patient did not experience any discomfort or visual symptoms resulting from the cyst. Conclusion: Surgical removal is not indicated for asymptomatic non-progressive free-floating iris cysts. The significance of a free-floating iris cyst in the setting of recurrent iritis remains unknown.

Impact of associated injuries in the Floating knee: A retrospective study

Science.gov (United States)

Rethnam, Ulfin; Yesupalan, Rajam S; Nair, Rajagopalan

2009-01-01

Background Floating knee injuries are usually associated with other significant injuries. Do these injuries have implications on the management of the floating knee and the final outcome of patients? Our study aims to assess the implications of associated injuries in the management and final outcome of floating knee. Methods 29 patients with floating knees were assessed in our institution. A retrospective analysis of medical records and radiographs were done and all associated injuries were identified. The impact of associated injuries on delay in initial surgical management, delay in rehabilitation & final outcome of the floating knee were assessed. Results 38 associated injuries were noted. 7 were associated with ipsilateral knee injuries. Lower limb injuries were most commonly associated with the floating knee. Patients with some associated injuries had a delay in surgical management and others a delay in post-operative rehabilitation. Knee ligament and vascular injuries were associated with poor outcome. Conclusion The associated injuries were quite frequent with the floating knee. Some of the associated injuries caused a delay in surgical management and post-operative rehabilitation. In assessment of the final outcome, patients with associated knee and vascular injuries had a poor prognosis. Majority of the patients with associated injuries had a good or excellent outcome. PMID:19144197

Floating Collection in an Academic Library: An Audacious Experiment That Succeeded

Science.gov (United States)

Coopey, Barbara; Eshbach, Barbara; Notartomas, Trish

2016-01-01

Can a floating collection thrive in a large multicampus academic research library? Floating collections have been successful in public libraries for some time, but it is uncommon for academic libraries and unheard of for a large academic library system. This article will discuss the investigation into the feasibility of a floating collection at…

MOSFET Electric-Charge Sensor

Science.gov (United States)

Robinson, Paul A., Jr.

1988-01-01

Charged-particle probe compact and consumes little power. Proposed modification enables metal oxide/semiconductor field-effect transistor (MOSFET) to act as detector of static electric charges or energetic charged particles. Thickened gate insulation acts as control structure. During measurements metal gate allowed to "float" to potential of charge accumulated in insulation. Stack of modified MOSFET'S constitutes detector of energetic charged particles. Each gate "floats" to potential induced by charged-particle beam penetrating its layer.

Measuring the Coefficient of Friction of a Small Floating Liquid Marble.

Science.gov (United States)

Ooi, Chin Hong; Nguyen, Anh Van; Evans, Geoffrey M; Dao, Dzung Viet; Nguyen, Nam-Trung

2016-12-02

This paper investigates the friction coefficient of a moving liquid marble, a small liquid droplet coated with hydrophobic powder and floating on another liquid surface. A floating marble can easily move across water surface due to the low friction, allowing for the transport of aqueous solutions with minimal energy input. However, the motion of a floating marble has yet to be systematically characterised due to the lack of insight into key parameters such as the coefficient of friction between the floating marble and the carrier liquid. We measured the coefficient of friction of a small floating marble using a novel experimental setup that exploits the non-wetting properties of a liquid marble. A floating liquid marble pair containing a minute amount magnetite particles were immobilised and then released in a controlled manner using permanent magnets. The capillarity-driven motion was analysed to determine the coefficient of friction of the liquid marbles. The "capillary charge" model was used to fit the experimental results. We varied the marble content and carrier liquid to establish a relationship between the friction correction factor and the meniscus angle.

The floating knee: epidemiology, prognostic indicators & outcome following surgical management

OpenAIRE

Yesupalan Rajam S; Rethnam Ulfin; Nair Rajagopalan

2007-01-01

Abstract Background Floating Knee injuries are complex injuries. The type of fractures, soft tissue and associated injuries make this a challenging problem to manage. We present the outcome of these injuries after surgical management. Methods 29 patients with floating knee injuries were managed over a 3 year period. This was a prospective study were both fractures of the floating knee injury were surgically fixed using different modalities. The associated injuries were managed appropriately. ...

Gate current for p+-poly PMOS devices under gate injection conditions

NARCIS (Netherlands)

Hof, A.J.; Holleman, J.; Woerlee, P.H.

2001-01-01

In current CMOS processing both n+-poly and p+-poly gates are used. The I-V –relationship and reliability of n+-poly devices are widely studied and well understood. Gate currents and reliability for p+-poly PMOS devices under gate injection conditions are not well understood. In this paper, the

A Community Terrain-Following Ocean Modeling System (ROMS)

Science.gov (United States)

2015-09-30

funded NOPP project titled: Toward the Development of a Coupled COAMPS-ROMS Ensemble Kalman filter and adjoint with a focus on the Indian Ocean and the...surface temperature and surface salinity daily averages for 31-Jan-2014. Similarly, Figure 3 shows the sea surface height averaged solution for 31-Jan... temperature (upper panel; Celsius) and surface salinity (lower panel) for 31-Jan-2014. The refined solution for the Hudson Canyon grid is overlaid on

Molecular Cloning, Expression and Characterization of Plasmid Encoding Rhomboid 4 (ROM4 of Tachyzoite of Toxoplasma gondii RH Strain

Directory of Open Access Journals (Sweden)

Mohammad Taghi RAHIMI

2017-12-01

Full Text Available AbstractBackground: The objective of this study was to clone, express and characterize the gene encoding rhomboid 4 (ROM4 proteins, a vital gene in surface adhesion and host cell invasion process of tachyzoite of T. gondii in an appropriate expression vector and eukaryotic cell for production of recombinant protein.Methods: Toxoplasma RNA was isolated from tachyzoites (RH strain and complementary DNA was synthesized. Oligonucleotide primer pair was designed based on Toxoplasma ROM4 gene sequence with XhoI and EcoRI restriction sites at 5´ end of forward and reverse primers, respectively. ROM4 gene was amplified by PCR, cloned into pTG19-T vector and the recombinant plasmid was sequenced. The gene was subcloned into pcDNA3 plasmid and expressed in CHO cells as eukaryotic cell. SDS-PAGE and western blotting were performed for protein determination and verification.Results: Cloning of ROM4 gene in pTG19-T vector was confirmed by colony-PCR and enzymatic digestion. The results of enzymatic digestion and gene sequencing confirmed successful cloning and subcloning procedures. The nucleotide sequence of the cloned ROM4 gene showed 99% homology compared to the corresponding sequences of original gene. SDS-PAGE and western blotting analyses of the purified protein revealed a single band having expected size of 65 kDa.Conclusion: This eukaryotic expression system is an appropriate system for high-level recombinant protein production of ROM4 gene from T. gondii tachyzoites used as antigenic component for serological assay and vaccine development.

Multiple Independent Gate FETs: How Many Gates Do We Need?

OpenAIRE

Amarù, Luca; Hills, Gage; Gaillardon, Pierre-Emmanuel; Mitra, Subhasish; De Micheli, Giovanni

2015-01-01

Multiple Independent Gate Field Effect Transistors (MIGFETs) are expected to push FET technology further into the semiconductor roadmap. In a MIGFET, supplementary gates either provide (i) enhanced conduction properties or (ii) more intelligent switching functions. In general, each additional gate also introduces a side implementation cost. To enable more efficient digital systems, MIGFETs must leverage their expressive power to realize complex logic circuits with few physical resources. Rese...

Transparently wrap-gated semiconductor nanowire arrays for studies of gate-controlled photoluminescence

Energy Technology Data Exchange (ETDEWEB)

Nylund, Gustav; Storm, Kristian; Torstensson, Henrik; Wallentin, Jesper; Borgström, Magnus T.; Hessman, Dan; Samuelson, Lars [Solid State Physics, Nanometer Structure Consortium, Lund University, Box 118, S-221 00 Lund (Sweden)

2013-12-04

We present a technique to measure gate-controlled photoluminescence (PL) on arrays of semiconductor nanowire (NW) capacitors using a transparent film of Indium-Tin-Oxide (ITO) wrapping around the nanowires as the gate electrode. By tuning the wrap-gate voltage, it is possible to increase the PL peak intensity of an array of undoped InP NWs by more than an order of magnitude. The fine structure of the PL spectrum reveals three subpeaks whose relative peak intensities change with gate voltage. We interpret this as gate-controlled state-filling of luminescing quantum dot segments formed by zincblende stacking faults in the mainly wurtzite NW crystal structure.

High voltage switches having one or more floating conductor layers

Science.gov (United States)

Werne, Roger W.; Sampayan, Stephen; Harris, John Richardson

2015-11-24

This patent document discloses high voltage switches that include one or more electrically floating conductor layers that are isolated from one another in the dielectric medium between the top and bottom switch electrodes. The presence of the one or more electrically floating conductor layers between the top and bottom switch electrodes allow the dielectric medium between the top and bottom switch electrodes to exhibit a higher breakdown voltage than the breakdown voltage when the one or more electrically floating conductor layers are not present between the top and bottom switch electrodes. This increased breakdown voltage in the presence of one or more electrically floating conductor layers in a dielectric medium enables the switch to supply a higher voltage for various high voltage circuits and electric systems.

Fear of Floating: Exchange Rate Flexibility Indices

OpenAIRE

Reinhart, Carmen

2001-01-01

Many emerging market countries have suffered financial crises. One view blames soft pegs for these crises. Adherents to that view suggest that countries move to corner solutions--hard pegs or floating exchange rates. We analyze the behavior of exchange rates, reserves, and interest rates to assess whether there is evidence that country practice is moving toward corner solutions. We focus on whether countries that claim they are floating are indeed doing so. We find that countries that say th...

Dynamic Response of a Floating Bridge Structure

OpenAIRE

Viuff, Thomas; Leira, Bernt Johan; Øiseth, Ole; Xiang, Xu

2016-01-01

A theoretical overview of the stochastic dynamic analysis of a floating bridge structure is presented. Emphasis is on the wave-induced response and the waves on the sea surface are idealized as a zero mean stationary Gaussian process. The first-order wave load processes are derived using linear potential theory and the structural idealization is based on the Finite Element Method. A frequency response calculation is presented for a simplified floating bridge structure example emphasising the ...

Arquitectura románica en la provincia de Soria, 1856-2014. Marco historiográfico y metodológico

Directory of Open Access Journals (Sweden)

Lorenzo Arribas, Josemi

2014-12-01

Full Text Available The historiography of Romanesque in the province of Soria has three different stages. The former one begins with Eduardo Saavedra’s researches (1856 and it extends until 1934, when Gaya Nuño defends his PhD Thesis (La arquitectura románica en la provincia de Soria, which will not be published until 1946. The Spanish Civil War and the post-war period mark the beginning of the second stage, which is merely transitional, lacking any important contribution. The last stage begins with the publication of the three volumes of the Enciclopedia del Románico en Castilla y León (2002. These works have largely improved the knowledge of Romanesque architectural heritage, enhanced besides by the task undertaken by the technical office of the Cultural Project Soria Románica (2007- 2012, responsible for studying and restoring more than thirty Romanesque buildings in the Southern part of province. It is within this working frame that the building recording of the churches here presented must be understood. This historiographical assessment about provincial Romanesque does not include those buildings sited in the capital city, the Cathedral of El Burgo de Osma, the Monastery of Santa Maria de Huerta and the hermitage of San Baudelio (Casillas de Berlanga.La historiografía del Románico en la provincia de Soria tiene tres etapas diferenciadas. Una inicial, que parte de los estudios de Eduardo Saavedra (1856 y se extiende hasta 1934, fecha de la lectura de la tesis doctoral de Gaya Nuño (La arquitectura románica en la provincia de Soria, cuya publicación, no obstante, se demora hasta 1946. La Guerra Civil y posguerra marcan el comienzo de la segunda etapa, transicional y sin grandes aportaciones. La última etapa se inaugura con la publicación de los tres volúmenes sorianos de la Enciclopedia del Románico en Castilla y León (2002. Esta obra ha multiplicado el conocimiento del patrimonio edilicio románico, acrecentado, después, por la labor de la

Development and evaluation of floating microspheres of curcumin in ...

African Journals Online (AJOL)

Purpose: To prepare and evaluate floating microspheres of curcumin for prolonged gastric residence and to study their effect on alloxan-induced diabetic rats. Methods: Floating microsphere were prepared by emulsion-solvent diffusion method, using hydroxylpropyl methylcellulose, chitosan and Eudragit S 100 polymer in ...

NODC Standard Product: World Ocean Circulation Experiment (WOCE) Global Data Resource (GDR), versions 1-3, on CD-ROM and DVD

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — NODC produced twelve (12) CD-ROMs containing WOCE Version 1 project data in the summer of 1998. NODC produced fifteen (15) CD-ROMs containing WOCE Version 2 project...

Economic Floating Waste Detectionfor Surface Cleaning Robots

Directory of Open Access Journals (Sweden)

Sumroengrit Jakkrit

2017-01-01

Full Text Available Removing waste out of water surface is a routine task and can be operated by using autonomous surface cleaning robots. This paper presents amethodoflaser-based floating waste detection for surface robot guidance when waste positions are unknown beforehand. Basing on concept of refraction and reflection of laser ray, the proposed laser-based technique is proven to be applicable on floating waste detection. The economic waste detector is constructed and mounted on the robot. Five DOF equations of motion are formulated for calculation of waste position incorporating distance measured by the laser and also the robot motion caused by external wind force as well as water surface tension. Experiments were conducted on a pond with calm water and results show that the presented economic waste detection successfully identify and locate position of plastic bottles floating on water surface within the range of 5 meters.

Evaluation of the acceptability of a CD-Rom as a health promotion tool for Inuit in Ottawa.

Science.gov (United States)

McShane, Kelly E; Smylie, Janet K; Hastings, Paul D; Prince, Conrad; Siedule, Connie

2013-01-01

There are few health promotion tools for urban Inuit, and there is a specific dearth of evaluations on such tools. The current study used a community-specific approach in the evaluation of a health promotion tool, based on an urban Inuit community's preferences of health knowledge sources and distribution strategies. In partnership with the Tungasuvvingat Inuit Family Health Team in Ottawa, a CD-Rom was developed featuring an Inuk Elder presenting prenatal health messages in both Inuktitut and English. Also, relevant evaluation materials were developed. Using a mixed methods approach, 40 participants completed interviews prior to viewing the CD-Rom and participated in a focus group at follow-up. Questionnaires were also completed pre- and post-viewing to assess changes between expectations and reactions in order to document acceptability. Significant increases were found on satisfaction, acceptability of medium and relevance of content ratings. Qualitative findings also included (a) interest, uncertainty and conditional interest prior to viewing; and (b) positive evaluations of the CD-Rom. This suggests that CD-Rom technology has the potential for health promotion for urban Inuit, and the community-specific evaluation approach yielded useful information.

Compound floating pivot micromechanisms

Science.gov (United States)

Garcia, Ernest J.

2001-04-24

A new class of tilting micromechanical mechanisms have been developed. These new mechanisms use compound floating pivot structures to attain far greater tilt angles than are practical using other micromechanical techniques. The new mechanisms are also capable of bi-directional tilt about multiple axes.

Formulation and evaluation of glipizide floating-bioadhesive tablets

Directory of Open Access Journals (Sweden)

Jayvadan K. Patel

2010-10-01

Full Text Available The purpose of this study was formulation and in vitro evaluation of floating-bioadhesive tablets to lengthen the stay of glipizide in its absorption area. Effervescent tablets were made using chitosan (CH, hydroxypropyl methylcellulose (HPMC, carbopolP934 (CP, polymethacrylic acid (PMA, citric acid, and sodium bicarbonate. Tablets with 5% effervescent base had longer lag time than 10%. The type of polymer had no significant effect on the floating lag time. All tablets floated atop the medium for 23-24 hr. Increasing carbopolP934 caused higher bioadhesion than chitosan (p < 0.05. All formulations showed a Higuchi, non-Fickian release mechanism. Tablets with 10% effervescent base, 80% CH/20% HPMC, or 80% CP/20% PMA seemed desirable.

Top-gate pentacene-based organic field-effect transistor with amorphous rubrene gate insulator

Science.gov (United States)

Hiroki, Mizuha; Maeda, Yasutaka; Ohmi, Shun-ichiro

2018-02-01

The scaling of organic field-effect transistors (OFETs) is necessary for high-density integration and for this, OFETs with a top-gate configuration are required. There have been several reports of damageless lithography processes for organic semiconductor or insulator layers. However, it is still difficult to fabricate scaled OFETs with a top-gate configuration. In this study, the lift-off process and the device characteristics of the OFETs with a top-gate configuration utilizing an amorphous (α) rubrene gate insulator were investigated. We have confirmed that α-rubrene shows an insulating property, and its extracted linear mobility was 2.5 × 10-2 cm2/(V·s). The gate length and width were 10 and 60 µm, respectively. From these results, the OFET with a top-gate configuration utilizing an α-rubrene gate insulator is promising for the high-density integration of scaled OFETs.

Floating Solar Photovoltaics Gaining Ground | State, Local, and Tribal

Science.gov (United States)

flotovoltaics (a trademarked term) or floating solar, represent an emerging application in which PV panels are , including efficiency gains (due to water cooling the panels), reductions in unwanted algae growth, slower 994 panels floating on 130 foam-filled pontoons atop the winery's irrigation pond and an additional

Natural Tasking of Robots Based on Human Interaction Cues (CD-ROM)

National Research Council Canada - National Science Library

Brooks, Rodney A

2005-01-01

...: 1 CD-ROM; 4 3/4 in.; 207 MB. ABSTRACT: We proposed developing the perceptual and intellectual abilities of robots so that in the field, war-fighters can interact with them in the same natural ways as they do with their human cohorts...

Analytical drain current formulation for gate dielectric engineered dual material gate-gate all around-tunneling field effect transistor

Science.gov (United States)

Madan, Jaya; Gupta, R. S.; Chaujar, Rishu

2015-09-01

In this work, an analytical drain current model for gate dielectric engineered (hetero dielectric)-dual material gate-gate all around tunnel field effect transistor (HD-DMG-GAA-TFET) has been developed. Parabolic approximation has been used to solve the two-dimensional (2D) Poisson equation with appropriate boundary conditions and continuity equations to evaluate analytical expressions for surface potential, electric field, tunneling barrier width and drain current. Further, the analog performance of the device is studied for three high-k dielectrics (Si3N4, HfO2, and ZrO2), and it has been investigated that the problem of lower ION, can be overcome by using the hetero-gate architecture. Moreover, the impact of scaling the gate oxide thickness and bias variations has also been studied. The HD-DMG-GAA-TFET shows an enhanced ION of the order of 10-4 A. The effectiveness of the proposed model is validated by comparing it with ATLAS device simulations.

Multi-span Suspension Bridge with Floating Towers

OpenAIRE

Brunstad, Orjan

2013-01-01

The Norwegian Public Roads Administration (NPRA) is currently conducting a feasible study of crossing 8 fjords on the west coast of Norway. The most challenging crossing is the 3700 m wide Sognefjord. Three main concepts are under development, and one of the concepts of this crossing is a three span suspension bridge on floating towers. The floating foundation suggested is a multi-column pontoon with mooring lines to seabed. The object of this thesis was to study this bridge concept with resp...

Current-Sensitive Path Planning for an Underactuated Free-Floating Ocean Sensorweb

Science.gov (United States)

Dahl, Kristen P.; Thompson, David R.; McLaren, David; Chao, Yi; Chien, Steve

2011-01-01

This work investigates multi-agent path planning in strong, dynamic currents using thousands of highly under-actuated vehicles. We address the specific task of path planning for a global network of ocean-observing floats. These submersibles are typified by the Argo global network consisting of over 3000 sensor platforms. They can control their buoyancy to float at depth for data collection or rise to the surface for satellite communications. Currently, floats drift at a constant depth regardless of the local currents. However, accurate current forecasts have become available which present the possibility of intentionally controlling floats' motion by dynamically commanding them to linger at different depths. This project explores the use of these current predictions to direct float networks to some desired final formation or position. It presents multiple algorithms for such path optimization and demonstrates their advantage over the standard approach of constant-depth drifting.

Hywind floating wind turbine project

Energy Technology Data Exchange (ETDEWEB)

Crome, Tim

2010-07-01

The Hywind floating wind turbine concept was developed by StatoilHydro. Technip was awarded the contract for engineering, fabrication and installation of a demonstration unit in May 2008 and the completed wind turbine was installed mid June 2009 at the west coast of Norway on 220 m water depth. The demonstration unit will generate 2,3 MW and is equipped with instrumentation for monitoring mooring forces, strains and motions. The fabrication of the SPAR type steel substructure was performed at Technip Offshore Finland facilities in Pori and was towed horizontally from Finland to Norway, where it was upended to a vertical position by water filling. The completed floating wind turbine was towed vertically to the final location west of Karmoey and connected to the pre-installed three legged anchor system using an Anchor Handling Tug type vessel. The wind turbine test period is scheduled to start in September 2009. Statoil will monitor the performance of the system for two years before decision will be taken for further development. The paper will present the main challenges and lessons learned through design, fabrication and installation of this first of its kind structure. Main emphasis will be on the special challenges experienced for this floating, catenary moored, slender unit which is highly exposed for wind induced forces in addition to current and waves in hostile North Sea environments. (Author)

Ionospheric data available on CD-ROM and on NDADS

International Nuclear Information System (INIS)

Bilitza, D.

1996-01-01

Information is provided on two CD-ROMs (for PCs) with ionospheric data: the ionosonde CD issued by NGDC/WDC-A-STP/NOAA/Boulder and the Atmosphere Explorer CD produced by NSSDC/WDC-A-R and S/NASA/Greenbelt. We also briefly describe the ionospheric/thermospheric data available through NSSDC's automated mail retrieval system (NDADS) and explain the procedure for obtaining NDADS data. (author). 3 figs

Extended onshore control of a floating wind turbine with wave disturbance reduction

DEFF Research Database (Denmark)

Christiansen, S.; Knudsen, T.; Bak, Thomas

2014-01-01

Reaching for higher wind resources floating wind turbines are being investigated. Wave induced loads significantly increase for floating wind turbines, and applying conventional onshore control strategies to floating wind turbines has been shown to impose negative damped oscillations in fore......-aft due to the low natural frequency of the floating structure. We suggest a control loop extension of the onshore controller which stabilizes the system and reduces the wave disturbance. The result is improved performance in power fluctuations, blade pitch activity, and platform oscillations...

Respiratory gating in positron emission tomography: A quantitative comparison of different gating schemes

International Nuclear Information System (INIS)

Dawood, Mohammad; Buether, Florian; Lang, Norbert; Schober, Otmar; Schaefers, Klaus P

2007-01-01

Respiratory gating is used for reducing the effects of breathing motion in a wide range of applications from radiotherapy treatment to diagnostical imaging. Different methods are feasible for respiratory gating. In this study seven gating methods were developed and tested on positron emission tomography (PET) listmode data. The results of seven patient studies were compared quantitatively with respect to motion and noise. (1) Equal and (2) variable time-based gating methods use only the time information of the breathing cycle to define respiratory gates. (3) Equal and (4) variable amplitude-based gating approaches utilize the amplitude of the respiratory signal. (5) Cycle-based amplitude gating is a combination of time and amplitude-based techniques. A baseline correction was applied to methods (3) and (4) resulting in two new approaches: Baseline corrected (6) equal and (7) variable amplitude-based gating. Listmode PET data from seven patients were acquired together with a respiratory signal. Images were reconstructed applying the seven gating methods. Two parameters were used to quantify the results: Motion was measured as the displacement of the heart due to respiration and noise was defined as the standard deviation of pixel intensities in a background region. The amplitude-based approaches (3) and (4) were superior to the time-based methods (1) and (2). The improvement in capturing the motion was more than 30% (up to 130%) in all subjects. The variable time (2) and amplitude (4) methods had a more uniform noise distribution among all respiratory gates compared to equal time (1) and amplitude (3) methods. Baseline correction did not improve the results. Out of seven different respiratory gating approaches, the variable amplitude method (4) captures the respiratory motion best while keeping a constant noise level among all respiratory phases

Canister Design for Deep Borehole Disposal of Nuclear Waste (CD-ROM)

National Research Council Canada - National Science Library

Hoag, Christopher I

2006-01-01

...: 1 CD-ROM; 4 3/4 in.; 28.7 MB. ABSTRACT: The objective of this thesis was to design a canister for the disposal of spent nuclear fuel and other high-level waste in deep borehole repositories using currently available and proven oil, gas...

[Cost-effectiveness in Dutch mental health care: future because of ROM?

NARCIS (Netherlands)

Agthoven, M. van; Kolk, A. van der; Knegtering, H.; Delespaul, P.A.; Arends, J.; Jeurissen, P.P.T.; Krabbe, P.F.M.; Huijsman, R.; Luijk, R.; Beurs, E. de; Hakkaart-van Roijen, L.; Bruggeman, R.

2015-01-01

BACKGROUND: The document reporting Dutch mental health care negotiations for 2014 - 2017 calls for a cost decrease based on cost-effectiveness. Thanks to rom, the Dutch mental health care seems well prepared for cost-effectiveness research.
AIM: Evaluate how valid cost-effectiveness research

Marketing and Selling CD-ROM Products on the World-Wide Web.

Science.gov (United States)

Walker, Becki

1995-01-01

Describes three companies' approaches to marketing and selling CD-ROM products on the World Wide Web. Benefits include low overhead for Internet-based sales, allowance for creativity, and ability to let customers preview products online. Discusses advertising, information delivery, content, information services, and security. (AEF)

Low-power DRAM-compatible Replacement Gate High-k/Metal Gate Stacks

Science.gov (United States)

Ritzenthaler, R.; Schram, T.; Bury, E.; Spessot, A.; Caillat, C.; Srividya, V.; Sebaai, F.; Mitard, J.; Ragnarsson, L.-Å.; Groeseneken, G.; Horiguchi, N.; Fazan, P.; Thean, A.

2013-06-01

In this work, the possibility of integration of High-k/Metal Gate (HKMG), Replacement Metal Gate (RMG) gate stacks for low power DRAM compatible transistors is studied. First, it is shown that RMG gate stacks used for Logic applications need to be seriously reconsidered, because of the additional anneal(s) needed in a DRAM process. New solutions are therefore developed. A PMOS stack HfO2/TiN with TiN deposited in three times combined with Work Function metal oxidations is demonstrated, featuring a very good Work Function of 4.95 eV. On the other hand, the NMOS side is shown to be a thornier problem to solve: a new solution based on the use of oxidized Ta as a diffusion barrier is proposed, and a HfO2/TiN/TaOX/TiAl/TiN/TiN gate stack featuring an aggressive Work Function of 4.35 eV (allowing a Work Function separation of 600 mV between NMOS and PMOS) is demonstrated. This work paves the way toward the integration of gate-last options for DRAM periphery transistors.

Planning and Preparation for CD-ROM Implementation: The Citadel Library.

Science.gov (United States)

Maynard, J. Edmund

Management guidelines for library planning and a strategic planning program profile based on the literature were used in the planning process for implementing access to databases on CD-ROM at the Daniel Library of the Citadel, Military College of South Carolina. According to this model, the planning process would consist of five stages: (1)…

CD-ROM technology at the EROS data center

Science.gov (United States)

Madigan, Michael E.; Weinheimer, Mary C.

1993-01-01

The vast amount of digital spatial data often required by a single user has created a demand for media alternatives to 1/2" magnetic tape. One such medium that has been recently adopted at the U.S. Geological Survey's EROS Data Center is the compact disc (CD). CD's are a versatile, dynamic, and low-cost method for providing a variety of data on a single media device and are compatible with various computer platforms. CD drives are available for personal computers, UNIX workstations, and mainframe systems, either directly connected, or through a network. This medium furnishes a quick method of reproducing and distributing large amounts of data on a single CD. Several data sets are already available on CD's, including collections of historical Landsat multispectral scanner data and biweekly composites of Advanced Very High Resolution Radiometer data for the conterminous United States. The EROS Data Center intends to provide even more data sets on CD's. Plans include specific data sets on a customized disc to fulfill individual requests, and mass production of unique data sets for large-scale distribution. Requests for a single compact disc-read only memory (CD-ROM) containing a large volume of data either for archiving or for one-time distribution can be addressed with a CD-write once (CD-WO) unit. Mass production and large-scale distribution will require CD-ROM replication and mastering.

Air Force Research Laboratorv Success Stories: A Review of 2004 (CD-ROM)

National Research Council Canada - National Science Library

2004-01-01

...). PHYSICAL DESCRIPTION: 1 CD-ROM; 4 3/4 in.; 43.5 MB. ABSTRACT: The Air Force Science and Technology Success Stories herein often represent the combined effort of several scientists and engineers working as a team...

Floating Oil-Spill Containment Device

Science.gov (United States)

Jones, Jack A.

2012-01-01

Previous oil containment booms have an open top that allows natural gas to escape, and have significant oil leakage due to wave action. Also, a subsea pyramid oil trap exists, but cannot move relative to moving oil plumes from deepsea oil leaks. The solution is to have large, moveable oil traps. One version floats on the sea surface and has a flexible tarp cover and a lower weighted skirt to completely entrap the floating oil and natural gas. The device must have at least three sides with boats pulling at each apex, and sonar or other system to track the slowly moving oil plume, so that the boats can properly locate the booms. The oil trap device must also have a means for removal of the oil and the natural gas. A second design version has a flexible pyramid cover that is attached by lines to ballast on the ocean floor. This is similar to fixed, metal pyramid oil capture devices in the Santa Barbara Channel off the coast of California. The ballast lines for the improved design, however, would have winches that can move the pyramid to always be located above the oil and gas plume. A third design is a combination of the first two. It uses a submerged pyramid to trap oil, but has no anchor and uses boats to locate the trap. It has ballast weights located along the bottom of the tarp and/or at the corners of the trap. The improved floating oil-spill containment device has a large floating boom and weighted skirt surrounding the oil and gas entrapment area. The device is triangular (or more than three sides) and has a flexible tarp cover with a raised gas vent area. Boats pull on the apex of the triangles to maintain tension and to allow the device to move to optimum locations to trap oil and gas. The gas is retrieved from a higher buoyant part of the tarp, and oil is retrieved from the floating oil layer contained in the device. These devices can be operated in relatively severe weather, since waves will break over the devices without causing oil leaking. Also, natural

Argo Float Data from the APDRC DAPPER Server, 1995-present

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — The floats are designed to drift at a fixed pressure (usually 1000 dbar) for 10 days. After this period, the floats move to a profiling pressure (usually between...

FLOAT2 WP4: Development of Materials

DEFF Research Database (Denmark)

Esteves, Luis Pedro; Aarup, Bendt

This report refers to complementary material testing to support the design and production of UHPC floaters for installation in the Wave Star Machine under FLOAT2 project. The main objective of WP4 is the characterization of mechanical properties of fiber-reinforced UHPC.......This report refers to complementary material testing to support the design and production of UHPC floaters for installation in the Wave Star Machine under FLOAT2 project. The main objective of WP4 is the characterization of mechanical properties of fiber-reinforced UHPC....

Effects of Electrolyte on Floating Water Bridge

OpenAIRE

Hideo Nishiumi; Fumitaka Honda

2009-01-01

Fuchs found phenomena that when high voltage is applied to deionized water filled in two contacted beakers, a floating water bridge forms spontaneously. In this paper, we examined flow direction of water bridge and what effects the addition of electrolytes such as NaCl, NaOH, and N H 4 C l to the floating water bridge would give. We found that ionization degree reduced the length of water bridge though insoluble electrolyte A l 2 O 3 had no effect on the length of water bridge.

The study to estimate the floating population in Seoul, Korea.

Science.gov (United States)

Lee, Geon Woo; Lee, Yong Jin; Kim, Youngeun; Hong, Seung-Han; Kim, Soohwaun; Kim, Jeong Soo; Lee, Jong Tae; Shin, Dong Chun; Lim, Youngwook

2017-01-01

Traffic-related pollutants have been reported to increase the morbidity of respiratory diseases. In order to apply management policies related to motor vehicles, studies of the floating population living in cities are important. The rate of metro rail transit system use by passengers residing in Seoul is about 54% of total public transportation use. Through the rate of metro use, the people-flow ratios in each administrative area were calculated. By applying a people-flow ratio based on the official census count, the floating population in 25 regions was calculated. The reduced level of deaths among the floating population in 14 regions having the roadside monitoring station was calculated as assuming a 20% reduction of mobile emission based on the policy. The hourly floating population size was calculated by applying the hourly population ratio to the regional population size as specified in the official census count. The number of people moving from 5 a.m. to next day 1 a.m. could not be precisely calculated when the population size was applied, but no issue was observed that would trigger a sizable shift in the rate of population change. The three patterns of increase, decrease, and no change of population in work hours were analyzed. When the concentration of particulate matter less than 10 μm in aerodynamic diameter was reduced by 20%, the number of excess deaths varied according to the difference of the floating population. The effective establishment of directions to manage the pollutants in cities should be carried out by considering the floating population. Although the number of people using the metro system is only an estimate, this disadvantage was supplemented by calculating inflow and outflow ratio of metro users per time in the total floating population in each region. Especially, 54% of metro usage in public transport causes high reliability in application.

The study to estimate the floating population in Seoul, Korea

Directory of Open Access Journals (Sweden)

Geon Woo Lee

2017-05-01

Full Text Available Traffic-related pollutants have been reported to increase the morbidity of respiratory diseases. In order to apply management policies related to motor vehicles, studies of the floating population living in cities are important. The rate of metro rail transit system use by passengers residing in Seoul is about 54% of total public transportation use. Through the rate of metro use, the people-flow ratios in each administrative area were calculated. By applying a people-flow ratio based on the official census count, the floating population in 25 regions was calculated. The reduced level of deaths among the floating population in 14 regions having the roadside monitoring station was calculated as assuming a 20% reduction of mobile emission based on the policy. The hourly floating population size was calculated by applying the hourly population ratio to the regional population size as specified in the official census count. The number of people moving from 5 a.m. to next day 1 a.m. could not be precisely calculated when the population size was applied, but no issue was observed that would trigger a sizable shift in the rate of population change. The three patterns of increase, decrease, and no change of population in work hours were analyzed. When the concentration of particulate matter less than 10 μm in aerodynamic diameter was reduced by 20%, the number of excess deaths varied according to the difference of the floating population. The effective establishment of directions to manage the pollutants in cities should be carried out by considering the floating population. Although the number of people using the metro system is only an estimate, this disadvantage was supplemented by calculating inflow and outflow ratio of metro users per time in the total floating population in each region. Especially, 54% of metro usage in public transport causes high reliability in application.

14 CFR 136.11 - Helicopter floats for over water.

Science.gov (United States)

2010-01-01

... 14 Aeronautics and Space 3 2010-01-01 2010-01-01 false Helicopter floats for over water. 136.11... TOURS AND NATIONAL PARKS AIR TOUR MANAGEMENT National Air Tour Safety Standards § 136.11 Helicopter floats for over water. (a) A helicopter used in commercial air tours over water beyond the shoreline must...

A Method for Modeling of Floating Vertical Axis Wind Turbine

DEFF Research Database (Denmark)

Wang, Kai; Hansen, Martin Otto Laver; Moan, Torgeir

2013-01-01

It is of interest to investigate the potential advantages of floating vertical axis wind turbine (FVAWT) due to its economical installation and maintenance. A novel 5MW vertical axis wind turbine concept with a Darrieus rotor mounted on a semi-submersible support structure is proposed in this paper....... In order to assess the technical and economic feasibility of this novel concept, a comprehensive simulation tool for modeling of the floating vertical axis wind turbine is needed. This work presents the development of a coupled method for modeling of the dynamics of a floating vertical axis wind turbine....... This integrated dynamic model takes into account the wind inflow, aerodynamics, hydrodynamics, structural dynamics (wind turbine, floating platform and the mooring lines) and a generator control. This approach calculates dynamic equilibrium at each time step and takes account of the interaction between the rotor...

Ambient Temperature Based Thermal Aware Energy Efficient ROM Design on FPGA

DEFF Research Database (Denmark)

Saini, Rishita; Bansal, Neha; Bansal, Meenakshi

2015-01-01

Thermal aware design is currently gaining importance in VLSI research domain. In this work, we are going to design thermal aware energy efficient ROM on Virtex-5 FPGA. Ambient Temperature, airflow, and heat sink profile play a significant role in thermal aware hardware design life cycle. Ambient...

The floating water bridge

International Nuclear Information System (INIS)

Fuchs, Elmar C; Woisetschlaeger, Jakob; Gatterer, Karl; Maier, Eugen; Pecnik, Rene; Holler, Gert; Eisenkoelbl, Helmut

2007-01-01

When high voltage is applied to distilled water filled in two glass beakers which are in contact, a stable water connection forms spontaneously, giving the impression of a floating water bridge. A detailed experimental analysis reveals static and dynamic structures as well as heat and mass transfer through this bridge

Float level indicator

International Nuclear Information System (INIS)

Grishchuk, M.Kh.; Laptev, A.G.; Pashkov, V.A.

1980-01-01

Specially developed level indicator is suggested with differential to-transformer converter of the float motion, operating in line with a movable electronic block, intended for indicating the level of the dissociating nitrogen tetroxide liquid phase. On the basis of the indicator elements the device is realized to measure the time of calibrated volume fillino. in by liquid nitrogen tetroxide in steady state operation of the experimental bench-marks [ru

In Praise of Mr. S. Platter and His Marvelous, Magnificent CD ROM Laser Disc Index for ERIC and PSYCHLIT.

Science.gov (United States)

Huffman, Robert F.

These instructions are designed to help patrons of the University of Missouri-Columbia library perform searches on PSYCHLIT, a CD-ROM (compact disc, read only memory) version of the Psych Abstracts database, and a CD-ROM version of the ERIC database, both produced by SilverPlatter Information Services. Basic information is provided about the disk…

Ranitidine Loaded Biopolymer Floats: Designing, Characterization, and Evaluation

Directory of Open Access Journals (Sweden)

Abdul Karim

2017-01-01

Full Text Available The float formulation is a strategy to improve the bioavailability of drugs by gastroretentive drug delivery system (GRDDS. A drug delivery model based on swellable and reswellable low density biopolymers has been designed to evaluate its drug release profile using ranitidine (RNT as a model drug and formulations have been prepared utilizing 32 factorial designs. The drug release (DR data has been subjected to various kinetic models to investigate the DR mechanism. A reduction in rate has been observed by expanding the amounts of PSG and LSG parts, while an expansion has been noted by increasing the concentration of tragacanth (TG and citric acid (CA with an increment in floating time. The stearic acid (SA has been used to decrease the lag time because a decrease in density of system was observed. The kinetic analysis showed that the optimized formulation (S4F3 followed zero-order kinetics and power law was found to be best fitted due to its minimum lag time and maximum floating ability. The resemblance of observed and predicted values indicated the validity of derived equations for evaluating the effect of independent variables while kinetic study demonstrated that the applied models are feasible for evaluating and developing float for RNT.

Methodology to Calculate the Costs of a Floating Offshore Renewable Energy Farm

Directory of Open Access Journals (Sweden)

Laura Castro-Santos

2016-04-01

Full Text Available This paper establishes a general methodology to calculate the life-cycle cost of floating offshore renewable energy devices, applying it to wave energy and wind energy devices. It is accounts for the contributions of the six main phases of their life-cycle: concept definition, design and development, manufacturing, installation, exploitation and dismantling, the costs of which have been defined. Moreover, the energy produced is also taken into account to calculate the Levelized Cost of Energy of a floating offshore renewable energy farm. The methodology proposed has been applied to two renewable energy devices: a floating offshore wave energy device and a floating offshore wind energy device. Two locations have been considered: Aguçadoura and São Pedro de Moel, both in Portugal. Results indicate that the most important cost in terms of the life-cycle of a floating offshore renewable energy farm is the exploitation cost, followed by the manufacturing and the installation cost. In addition, the best area in terms of costs is the same independently of the type of floating offshore renewable energy considered: Aguçadoura. However, the results in terms of Levelized Cost of Energy are different: Aguçadoura is better when considering wave energy technology and the São Pedro de Moel region is the best option when considering floating wind energy technology. The method proposed aims to give a direct approach to calculate the main life-cycle cost of a floating offshore renewable energy farm. It helps to assess its feasibility and evaluating the relevant characteristics that influence it the most.

Floating cultivation of marine cyanobacteria using coal fly ash.

Science.gov (United States)

Matsumoto, M; Yoshida, E; Takeyama, H; Matsunaga, T

2000-01-01

The aim of this study was to develop improved methodologies for bulk culturing of biotechnologically useful marine cyanobacteria in the open ocean. We have investigated the viability of using coal fly ash (CFA) blocks as the support medium in a novel floating culture system for marine micro-algae. The marine cyanobacterium Synechococcus sp. NKBG 040607 was found to adhere to floating CFA blocks in liquid culture medium. Maximum density of attached cells of 2.0 x 10(8) cells/cm2 was achieved using seawater. The marine cyanobacterium Synechococcus sp. NKBG 042902 weakly adhered to floating CFA blocks in BG-11 medium. Increasing the concentration of calcium ion in the culture medium enhanced adherence to CFA blocks.

An electrically reprogrammable 1024 bits MNOS ROM using MNOS-SOS e/d technology

International Nuclear Information System (INIS)

Mackowiak, E.; Le Goascoz, V.

1976-01-01

A 1024 bits fully decoded electrically writable and erasable non volatile ROM is described. Memory cells and peripheral circuits are made using P channel silicon on sapphire enhancement depletion technology [fr

Students' Attitudes toward ABI/INFORM on CD-ROM: A Factor Analysis.

Science.gov (United States)

Wang, Vicky; Lau, Shuk-fong

Two years after the introduction of CD-ROM bibliographic database searching in the Memphis State University libraries (Tennessee), a survey was conducted to examine students' attitudes toward the business database, ABI/INFORM. ABI/INFORM contains indexes and abstracts of articles from over 800 journals on management, accounting, banking, human…

Energy-Smart Choices for Schools. An HVAC Comparison Tool. [CD-ROM].

Science.gov (United States)

Geothermal Heat Pump Consortium, Inc., Washington, DC.

A CD ROM program provides comparison construction cost capabilities for heating, ventilation, and air conditioning (HVAC) systems in educational facilities. The program combines multiple types of systems with square footage data on low and high construction cost and school size to automatically calculate HVAC comparative construction costs. (GR)

Response estimation for a floating bridge using acceleration output only

NARCIS (Netherlands)

Petersen, Øyvind Wiig; Øiseth, Ole; Nord, Torodd Skjerve; Lourens, E.; Sas, P.; Moens, D.; van de Walle, A.

2016-01-01

The Norwegian Public Roads Administration is reviewing the possibility of using floating bridges as fjord crossings. The dynamic behaviour of very long floating bridges with novel designs are prone to uncertainties. Studying the dynamic behaviour of existing bridges is valuable for understanding

Biogeochemical sensor performance in the SOCCOM profiling float array

Science.gov (United States)

Johnson, Kenneth S.; Plant, Joshua N.; Coletti, Luke J.; Jannasch, Hans W.; Sakamoto, Carole M.; Riser, Stephen C.; Swift, Dana D.; Williams, Nancy L.; Boss, Emmanuel; Haëntjens, Nils; Talley, Lynne D.; Sarmiento, Jorge L.

2017-08-01

The Southern Ocean Carbon and Climate Observations and Modeling (SOCCOM) program has begun deploying a large array of biogeochemical sensors on profiling floats in the Southern Ocean. As of February 2016, 86 floats have been deployed. Here the focus is on 56 floats with quality-controlled and adjusted data that have been in the water at least 6 months. The floats carry oxygen, nitrate, pH, chlorophyll fluorescence, and optical backscatter sensors. The raw data generated by these sensors can suffer from inaccurate initial calibrations and from sensor drift over time. Procedures to correct the data are defined. The initial accuracy of the adjusted concentrations is assessed by comparing the corrected data to laboratory measurements made on samples collected by a hydrographic cast with a rosette sampler at the float deployment station. The long-term accuracy of the corrected data is compared to the GLODAPv2 data set whenever a float made a profile within 20 km of a GLODAPv2 station. Based on these assessments, the fleet average oxygen data are accurate to 1 ± 1%, nitrate to within 0.5 ± 0.5 µmol kg-1, and pH to 0.005 ± 0.007, where the error limit is 1 standard deviation of the fleet data. The bio-optical measurements of chlorophyll fluorescence and optical backscatter are used to estimate chlorophyll a and particulate organic carbon concentration. The particulate organic carbon concentrations inferred from optical backscatter appear accurate to with 35 mg C m-3 or 20%, whichever is larger. Factors affecting the accuracy of the estimated chlorophyll a concentrations are evaluated.Plain Language SummaryThe ocean science community must move toward greater use of autonomous platforms and sensors if we are to extend our knowledge of the effects of climate driven change within the ocean. Essential to this shift in observing strategies is an understanding of the performance that can be obtained from biogeochemical sensors on platforms deployed for years and the

Floating Microparticulate Oral Diltiazem Hydrochloride Delivery ...

African Journals Online (AJOL)

Delivery System for Improved Delivery to Heart ... Conclusion: Microparticulate floating (gastroretentive) oral drug delivery system of diltiazem prepared ..... treatment of cardiac disease. ... hydrochloride-loaded mucoadhesive microspheres.

Operating Experience with Nuclear Power Stations in Member States in 2014. 2015 Edition (CD-ROM)

International Nuclear Information System (INIS)

2015-01-01

This CD-ROM contains the 46th edition of the IAEA’s series of annual reports on operating experience with nuclear power plants in Member States. It is a direct output from the IAEA’s Power Reactor Information System (PRIS) and contains information on electricity production and overall performance of individual plants during 2014. In addition to annual information, the report contains a historical summary of performance during the lifetime of individual plants and figures illustrating worldwide performance of the nuclear industry. The CD-ROM contains also an overview of design characteristics and dashboards of all operating nuclear power plants worldwide

SM-ROM-GL (Strong Motion Romania Ground Level Database

Directory of Open Access Journals (Sweden)

Ioan Sorin BORCIA

2015-07-01

Full Text Available The SM-ROM-GL database includes data obtained by the processing of records performed at ground level by the Romanian seismic networks, namely INCERC, NIEP, NCSRR and ISPH-GEOTEC, during recent seismic events with moment magnitude Mw ≥ 5 and epicenters located in Romania. All the available seismic records were re-processed using the same basic software and the same procedures and options (filtering and baseline correction, in order to obtain a consistent dataset. The database stores computed parameters of seismic motions, i.e. peak values: PGA, PGV, PGD, effective peak values: EPA, EPV, EPD, control periods, spectral values of absolute acceleration, relative velocity and relative displacement, as well as of instrumental intensity (as defined bz Sandi and Borcia in 2011. The fields in the database include: coding of seismic events, stations and records, a number of associated fields (seismic event source parameters, geographical coordinates of seismic stations, links to the corresponding ground motion records, charts of the response spectra of absolute acceleration, relative velocity, relative displacement and instrumental intensity, as well as some other representative parameters of seismic motions. The conception of the SM-ROM-GL database allows for an easy maintenance; such that elementary knowledge of Microsoft Access 2000 is sufficient for its operation.

Fabrication of Nonvolatile Memory Effects in High-k Dielectric Thin Films Using Electron Irradiation

International Nuclear Information System (INIS)

Park, Chanrock; Cho, Daehee; Kim, Jeongeun; Hwang, Jinha

2010-01-01

Electron Irradiation can be applied towards nano-floating gate memories which are recognized as one of the next-generation nonvolatile memory semiconductors. NFGMs can overcome the preexisting limitations encountered in Dynamic Random Access Memories and Flash memories with the excellent advantages, i. e. high-density information storage, high response speed, high compactness, etc. The traditional nano-floating gate memories are fabricated through multi-layered nano structures of the dissimilar materials where the charge-trapping portions are sandwiched into the high-k dielectrics. However, this work reports the unique nonvolatile responses in single-layered high-k dielectric thin films if irradiated with highly accelerated electron beams. The implications of the electron irradiation will be discussed towards high-performance nano-floating gate memories

Collector floating potentials in a discharge plasma

International Nuclear Information System (INIS)

Cercek, M.; Gyergyek, T.

1999-01-01

We present the results of a study on electrode floating potential formation in a hot-cathode discharge plasma. The electron component of the plasma is composed from two populations. The high temperature component develops from primary electrons and the cool component from secondary electrons born by ionisation of cold neutral gas. A static, kinetic plasma-sheath model is use to calculate the pre-sheath potential and the floating potential of the electrode. For hot primary electrons a truncated Maxwellian distribution is assumed. The plasma system is also modelled numerically with a dynamic, electrostatic particle simulation. The plasma source injects temporally equal fluxes of ions and electrons with half-Maxwellian velocities. Again, the hot electron distribution is truncated in the high velocity tail. The plasma parameters, such as ion temperature and mass, electron temperatures, discharge voltages, etc. correspond to experimental values. The experimental measurements of the electrode floating potential are performed in weakly magnetised plasma produced with hot cathode discharge in argon gas. Theoretical, simulation and experimental results are compared and they agree very well.(author)

Maiden Voyage of the Under-Ice Float

Science.gov (United States)

Shcherbina, A.; D'Asaro, E. A.; Light, B.; Deming, J. W.; Rehm, E.

2016-02-01

The Under-Ice Float (UIF) is a new autonomous platform for sea ice and upper ocean observations in the marginal ice zone (MIZ). UIF is based on the Mixed Layer Lagrangian Float design, inheriting its accurate buoyancy control and relatively heavy payload capability. A major challenge for sustained autonomous observations in the MIZ is detection of open water for navigation and telemetry surfacings. UIF employs the new surface classification algorithm based on the spectral analysis of surface roughness sensed by an upward-looking sonar. A prototype UIF was deployed in the MIZ of the central Arctic Ocean in late August 2015. The main payload of the first UIF was a bio-optical suit consisting of upward- and downward hyperspectral radiometers; temperature, salinity, chlorophyll, turbidity, and dissolved oxygen sensors, and a high-definition photo camera. In the early stages of its mission, the float successfully avoided ice, detected leads, surfaced in open water, and transmitted data and photographs. We will present the analysis of these observations from the full UIF mission extending into the freeze-up season.

a Design of the Driver Airbag Module with Floating Horn Assembly

Science.gov (United States)

Suh, Chang-Min; Lee, Young-Hoon; Suh, Duck-Young

The driver airbag system is designed as a supplemental restraint system in addition to the seatbelt, and is designed to protect the driver's head and chest against severe injury by a device that is actuated in case of vehicle's fronted impact. Deployment of an airbag module with floating horn assembly is a highly dynamic process. The concept of driver airbag module with floating horn assembly and aluminum emblem is presented as a useful parameter when the airbag deploys and the energy is evaluated as performance factor in airbag module. Floating horn assembly is also one of the major factors for driver airbag module design to perform its horn function and check the package between driver airbag module and steering wheel. This study on the design of driver airbag module with floating horn assembly proved the feasibility as a new safety device. However, the system level study is needed for decrease of passenger injury. This study can be used for the implementation of a prototype of DABM with floating horn device.

The capture rate of free-floating planets in our galaxy

Science.gov (United States)

Goulinski, N.; Ribak, E. N.

2017-09-01

We propose that planetary nebulae and supernova remnants may constitute a significant source of free-floating planets. With a large population of free-floating planets, the rate at which these planets get captured by planetary systems may be non-negligible. We predict that about one out of every 100 sub-solar stars are expected to experience a capture of a free-floating planet during their lifetime. The capture cross section calculated through three-body scattering simulations in vacuum conditions. Since planetary systems usually contain multiple planets, and dissipation processes where not included in the simulation, the capture rate may be higher.

Turbomachinery systems for floating production applications

Energy Technology Data Exchange (ETDEWEB)

Windt, Jonathan P.; Kurz, Rainer [Solar Turbines Incorporated, San Diego, CA (United States)

2008-07-01

Since 1995 there has been a dramatic increase in oil and gas exploration and production using floating platforms in deeper waters located further offshore. This exploration started with tension leg platforms, progressed through SPARs and Semi-Submersibles, and later evolved into Floating Production Storage and Offloading (FPSO) vessels. Turbomachinery equipment installed on a floating platform or vessel will be expected to operate in the same manner as a land based machine, but in a variety of climate and environmental conditions that now includes motion. To operate successfully, specific design considerations for the turbo-machinery packages are required. It is critical to take into account the type of vessel, the expected list, trim and dynamic motion angles, the dynamic forces applied, the expected deck deflection as a result of those forces, understand the applicable class requirement, and where the equipment will be located on the vessel. This information is then translated into the design conditions to determine the type of mounting method to be used to attach the turbo-machinery package to the deck, the expected accelerations for structural analysis, and oil tank and system designs for fluid management. Furthermore, compressor designs need to allow utmost flexibility to adapt to changing operating conditions. (author)

Development and testing of a CD-ROM program for improving adolescent knowledge of inflammatory bowel disease.

Science.gov (United States)

Boamah, Lynelle M; Bohren, Janet R; Pentiuk, Scott; Baker, Raymond; Yi, Michael; Moyer, M Susan

2010-05-01

The aim of this study was to design a theory-based educational program for adolescents with inflammatory bowel disease (IBD) using an interactive multimedia CD-ROM and to test its effectiveness in improving knowledge in IBD. Curriculum-based instruction using educational theory and principles was designed for adolescents on an interactive multimedia CD-ROM. Twenty subjects completed summative evaluation of the CD-ROM measuring gain in knowledge about IBD immediately and 9 months after instruction. Subjects found the CD-ROM to be informative, appealing, and easy to use. The mean baseline score of the adolescents on the Crohn's and Colitis Knowledge questionnaire was 12.2 (standard deviation 5.14, range 3-24). After an average of 30 minutes of self-directed learning, adolescent subjects increased their posttest score to a mean of 19.8, a gain of 7.6 points over baseline (95% confidence interval 5.2-10.1, P < 0.0001). Knowledge of medications, disease complications, and gastrointestinal structure and function was gained and retained upon retesting at 9 months with a mean Crohn's and Colitis Knowledge questionnaire score of 17.5 (standard deviation 3.9, range 12-26), which was still an improvement over the mean pretest knowledge score of 12.2 (P < 0.001). Adolescents with IBD have low baseline knowledge about their disease. A rigorously developed interactive educational tool is now available for instructing adolescent patients about their IBD.

The effects of neural mobilization on cervical radiculopathy patients' pain, disability, ROM, and deep flexor endurance.

Science.gov (United States)

Kim, Dong-Gyu; Chung, Sin Ho; Jung, Ho Bal

2017-09-22

Cervical radiculopathy (CR) is a disease of the cervical spine and a space-occupying lesion that occurs because of pathological problems with cervical nerve roots. Nerve root injury to produce functional disability. The purpose of this study was to examine the effects of neural mobilization with manual cervical traction (NMCT) compared with manual cervical traction (MCT) on pain, functional disability, muscle endurance, and range of motion (ROM) in individuals with CR patients. A blinded randomized clinical trial was conducted. Thirty CR patients were divided into two groups - those who received NMCT and those who received MCT. The intervention was applied three times per week for eight weeks. It was measured in order to determine the pain and functional disability in patients with CR. The numeric pain rating scale (NPRS), neck disability index (NDI), ROM, and deep flexor endurance of patients were measured prior to the experiment, four weeks, and eight weeks after the experiment to compare the time points. A repeated-measures analysis of variance was used to compare differences within each group prior to the experiment. And Bonferroni test was performed to examine the significance of each time point. There were significant differences within each group prior to the intervention, four weeks after the intervention, and eight weeks after the intervention in NPRS, NDI, ROM, and deep flexor endurance (Ppain relief, recovery from neck disability, ROM, and deep flexor endurance for patients with CR.

經由校園網路存取圖書館光碟資料庫之研究 Studies on Multiuser Access Library CD-ROM Database via Campus Network

Directory of Open Access Journals (Sweden)

Ruey-shun Chen

1992-06-01

Full Text Available 無Library CD-ROM with its enormous storage, retrieval capabilities and reasonable price. It has been gradually replacing some of its printed counterpart. But one of the greatest limitation on the use of stand-alone CD-ROM workstation is that only one user can access the CD-ROM database at a time. This paper is proposed a new method to solve this problem. The method use personal computer via standard network system Ethernet high speed fiber network FADDY and standard protocol TCP/IP can access library CD-ROM database and perform a practical CD-ROM campus network system. Its advantage reduce redundant CD-ROM purchase fee and reduce damage by handed in and out and allows multiuser to access the same CD-ROM disc simultaneously.

Expert Oracle GoldenGate

CERN Document Server

Prusinski, Ben; Chung, Richard

2011-01-01

Expert Oracle GoldenGate is a hands-on guide to creating and managing complex data replication environments using the latest in database replication technology from Oracle. GoldenGate is the future in replication technology from Oracle, and aims to be best-of-breed. GoldenGate supports homogeneous replication between Oracle databases. It supports heterogeneous replication involving other brands such as Microsoft SQL Server and IBM DB2 Universal Server. GoldenGate is high-speed, bidirectional, highly-parallelized, and makes only a light impact on the performance of databases involved in replica

Cooperative control system of the floating cranes for the dual lifting

OpenAIRE

Mihee Nam; Jinbeom Kim; Jaechang Lee; Daekyung Kim; Donghyuk Lee; Jangmyung Lee

2018-01-01

This paper proposes a dual lifting and its cooperative control system with two different kinds of floating cranes. The Mega-erection and Giga-erection in the ship building are used to handle heavier and wider blocks and modules as ships and off-shore platforms are enlarged. However, there is no equipment to handle such Tera-blocks. In order to overcome the limit on performance of existing floating cranes, the dual lifting is proposed in this research. In the dual lifting, two floating cranes ...

Cooperative control system of the floating cranes for the dual lifting

Directory of Open Access Journals (Sweden)

Mihee Nam

2018-01-01

Full Text Available This paper proposes a dual lifting and its cooperative control system with two different kinds of floating cranes. The Mega-erection and Giga-erection in the ship building are used to handle heavier and wider blocks and modules as ships and off-shore platforms are enlarged. However, there is no equipment to handle such Tera-blocks. In order to overcome the limit on performance of existing floating cranes, the dual lifting is proposed in this research. In the dual lifting, two floating cranes are well-coordinated to add up the lift capabilities of both cranes without any loss such that virtually a single crane is lifting, maneuvering and unloading. Two main constraints for the dual lifting are as follows: First, two barges of floating cranes should be constrained as a rigid body not to cause a relative motion between two barges and main hooks of the two cranes should be controlled as main hooks of a single crane. In order words, it is necessary to develop the cooperative control of two floating cranes in order to sustain a center of gravity of the module and minimize the tilting angle during the lifting and unloading by the two floating cranes. Two floating cranes are handled as a master-slave system. The master crane is able to gather information about all working conditions and make a decision to control the individual hook speed, which communicates the slave crane by TCP/IP. The developed control system has been embedded in the real floating crane systems and the dual lifting has been demonstrated five times at SHI shipyard in 2015. The moving angles of the lifting module are analyzed and verified to be suitable for hoisting control. It is verified that the dual lifting can be applied for many heavier and wider blocks and modules to shorten the construction time of ships and off-shore platforms.

Can Heavier Liquid Float on Top of a Lighter One?

International Nuclear Information System (INIS)

Ayyad, A. H.; Takrori, F.

2011-01-01

We report on a first observation of a floating spherical Hg (density 13 g/cm 3 ) drop on top of a glycerin (density 1.26 g/cm 3 ) drop, the latter is hemispherical and about four times larger in volume. This observation is clearly against nature's gravity law and has never been reported before. Here we present spectacular high resolution photos that clearly demonstrate this remarkable floating phenomenon. Using milli-Q water, the Hg drop would stay down adhered at the triple line. Instead, the coincidental use of tap water displays the same phenomenon. Increasing the volume of the supporting liquid to a certain value causes the Hg drop to sink. A 5-M NaCl aqueous solution is found enough to show the same floating phenomenon. This floating mercury as a phenomenon is puzzling. On this length scale it seems that surface tension and curvature dominate over gravity. (fundamental areas of phenomenology (including applications))

Adolescencia, relaciones románticas y actividad sexual: una revisión

Directory of Open Access Journals (Sweden)

Elvia Vargas

2002-01-01

Full Text Available Se presenta una revisión de algunas de las investigaciones más recientes sobre la adolescencia y los factores asociados a las relaciones románticas y la actividad sexual durante la adolescencia. Se parte de la premisa de que el análisis de la iniciación romántica y sexual durante la adolescencia requiere de modelos de causalidad múltiple que permitan dar cuenta, conjuntamente, de los factores que se encuentran en los contextos individual, familiar y social asociados con estos dos procesos. Se destaca el papel de los padres en el desarrollo de hijos adolescentes autónomos, capaces de manejar la influencia negativa del grupo de pares. Se hacen algunas recomendaciones a los responsables de diseñar programas de prevención y a los interesados en el estudio de la adolescencia y en el desarrollo de la disciplina

Hydroelasticity of a Floating Plate

DEFF Research Database (Denmark)

Chen, X.; Jensen, Jørgen Juncher; Cui, W.

2003-01-01

The membrane forces are included in the hydroelastic analysis of a floating plate undergoing large vertical deflections in regular monochromatic multidirectional waves. The first-order vertical displacements induced by the linear wave exciting forces are calculated by the mode expansion method in...

The impact of the night float system on internal medicine residency programs.

Science.gov (United States)

Trontell, M C; Carson, J L; Taragin, M I; Duff, A

1991-01-01

To study the design, method of implementation, perceived benefits, and problems associated with a night float system. Self-administered questionnaire completed by program directors, which included both structured and open-ended questions. The answers reflect resident and student opinions as well as those of the program directors, since program directors regularly obtain feedback from these groups. The 442 accredited internal medicine residency programs listed in the 1988-89 Directory of Graduate Medical Education Programs. Of the 442 programs, 79% responded, and 30% had experience with a night float system. The most frequent methods for initiating a night float system included: decreasing elective time (42.3%), hiring more residents (26.9%), creating a non-teaching service (12.5%), and reallocating housestaff time (9.6%). Positive effects cited include decreased fatigue, improved housestaff morale, improved recruiting, and better attitude toward internal medicine training. The quality of medical care was considered the same or better by most programs using it. The most commonly cited problems were decreased continuity of care, inadequate teaching of the night float team, and miscommunication. Residency programs using a night float system usually observe a positive effect on housestaff morale, recruitment, and working hours and no detrimental effect on the quality of patient care. Miscommunication and inadequate learning experience for the night float team are important potential problems. This survey suggests that the night float represents one solution to reducing resident working hours.

CD-ROM training course in quality assurance in diagnostic imaging

International Nuclear Information System (INIS)

Khoury, H.J.; Machado, P.; Drexler, G.

2001-01-01

This paper discusses the CD-ROM elaborated to provide a continuous professional formation and a practical guidance on the implementation and operation of routine quality assurance (QA) programme for medical physicists, regulator authorities and for those personnel concerned with the daily provision of diagnostic radiology services. The CD-ROM contains topics on the basic concepts of QA in radiodiagnostic, and it also allows the user to visualise effects on the variation of technical parameters (tube potential (kV) and current (mA), filtration) in the quality of the image. This possibility will contribute to the better understanding of the phenomena associated with the quality of the image. Besides, the program contains the procedures for the execution of the tests of the equipment and the route of implantation of program of quality assurance. It is interactive with the user, it fills a gap in the medical physics area and it allows the student's continuous formation because it assists the beginner, with the basic concepts, and the professional, with the aid in the implantation of the program of QA. The presentation is in the Portuguese language. (author)

Design and Evaluation of an Oral Floating Matrix Tablet of ...

African Journals Online (AJOL)

Purpose: To develop floating matrix tablets of salbutamol sulphate using ethyl cellulose and acrycoat S-100 as polymers, and sodium bicarbonate, citric acid and tartaric acid as gas generating agents. Methods: Twenty four formulations were prepared and segregated into four major categories, A to D. The floating tablets ...

14 CFR 25.529 - Hull and main float landing conditions.

Science.gov (United States)

2010-01-01

... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false Hull and main float landing conditions. 25... AIRCRAFT AIRWORTHINESS STANDARDS: TRANSPORT CATEGORY AIRPLANES Structure Water Loads § 25.529 Hull and main.... (b) Unsymmetrical landing for hull and single float seaplanes. Unsymmetrical step, bow, and stern...

Dynamic modeling of a spar-type floating offshore wind turbine

NARCIS (Netherlands)

Savenije, L.B.; Ashuri, T.; Van Bussel, G.J.W.; Staerdahl, J.W.

2010-01-01

The installation of floating wind farms in deeper water is encouraged by the stronger and steadier wind, the lower visibility and noise impact, the absence of road restrictions, but also the absence or shortage of shallow water. In the summer of 2009, the first large-scale floating wind turbine

Estimation of Structure-Borne Noise Reduction Effect of Steel Railway Bridge Equipped with Floating Ladder Track and Floating Reinforced-Concrete Deck

Science.gov (United States)

Watanabe, Tsutomu; Sogabe, Masamichi; Asanuma, Kiyoshi; Wakui, Hajime

A number of steel railway bridges have been constructed in Japan. Thin steel members used for the bridges easily tend to vibrate and generate structure-borne noise. Accordingly, the number of constructions of steel railway bridges tends to decrease in the urban areas from a viewpoint of environmental preservation. Then, as a countermeasure against structure-borne noise generated from steel railway bridges, we have developed a new type of the steel railway bridge equipped with a floating-ladder track and a floating reinforced-concrete (RC) deck. As a result of train-running experiment, it became apparent that the new steel railway bridge installed by double floating system has reduced a vibration velocity level by 10.5 dB(A) at main girder web as compared with a steel railway bridge installed by directly fastened track. This reduction effect was achieved by the ladder track and RC deck supported by resilient materials.

Life cycle assessment of a floating offshore wind turbine

Energy Technology Data Exchange (ETDEWEB)

Weinzettel, Jan [Department of Electrotechnology, Faculty of Electrical Engineering, Czech Technical University in Prague, Technicka 2, Praha 166 27 (Czech Republic); Charles University in Prague Environment Center, U Krize 8, Prague 158 00 (Czech Republic); Reenaas, Marte; Solli, Christian [Industrial Ecology Programme, Norwegian University of Science and Technology (NTNU), 7491 Trondheim (Norway); Hertwich, Edgar G. [Industrial Ecology Programme, Norwegian University of Science and Technology (NTNU), 7491 Trondheim (Norway); Department of Energy and Process Engineering, Norwegian University of Science and Technology (NTNU), 7491 Trondheim (Norway)

2009-03-15

A development in wind energy technology towards higher nominal power of the wind turbines is related to the shift of the turbines to better wind conditions. After the shift from onshore to offshore areas, there has been an effort to move further from the sea coast to the deep water areas, which requires floating windmills. Such a concept brings additional environmental impact through higher material demand. To evaluate additional environmental burdens and to find out whether they can be rebalanced or even offset by better wind conditions, a prospective life cycle assessment (LCA) study of one floating concept has been performed and the results are presented in this paper. A comparison with existing LCA studies of conventional offshore wind power and electricity from a natural gas combined cycle is presented. The results indicate similar environmental impacts of electricity production using floating wind power plants as using non-floating offshore wind power plants. The most important stage in the life cycle of the wind power plants is the production of materials. Credits that are connected to recycling these materials at the end-of-life of the power plant are substantial. (author)

Modelling and Simulation of Free Floating Pig for Different Pipeline Inclination Angles

Directory of Open Access Journals (Sweden)

Woldemichael Dereje Engida

2016-01-01

Full Text Available This paper presents a modelling and simulation of free floating pig to determine the flow parameters to avoid pig stalling in pigging operation. A free floating spherical shaped pig was design and equipped with necessary sensors to detect leak along the pipeline. The free floating pig does not have internal or external power supply to navigate through the pipeline. Instead, it is being driven by the flowing medium. In order to avoid stalling of the pig, it is essential to conduct simulation to determine the necessary flow parameters for different inclination angles. Accordingly, a pipeline section with inclination of 0°, 15°, 30°, 45°, 60°, 75°, and 90° were modelled and simulated using ANSYS FLUENT 15.0 with water and oil as working medium. For each case, the minimum velocity required to propel the free floating pig through the inclination were determined. In addition, the trajectory of the free floating pig has been visualized in the simulation.

GATE V6: a major enhancement of the GATE simulation platform enabling modelling of CT and radiotherapy

Energy Technology Data Exchange (ETDEWEB)

Jan, S; Becheva, E [DSV/I2BM/SHFJ, Commissariat a l' Energie Atomique, Orsay (France); Benoit, D; Rehfeld, N; Stute, S; Buvat, I [IMNC-UMR 8165 CNRS-Paris 7 and Paris 11 Universities, 15 rue Georges Clemenceau, 91406 Orsay Cedex (France); Carlier, T [INSERM U892-Cancer Research Center, University of Nantes, Nantes (France); Cassol, F; Morel, C [Centre de physique des particules de Marseille, CNRS-IN2P3 and Universite de la Mediterranee, Aix-Marseille II, 163, avenue de Luminy, 13288 Marseille Cedex 09 (France); Descourt, P; Visvikis, D [INSERM, U650, Laboratoire du Traitement de l' Information Medicale (LaTIM), CHU Morvan, Brest (France); Frisson, T; Grevillot, L; Guigues, L; Sarrut, D; Zahra, N [Universite de Lyon, CREATIS, CNRS UMR5220, Inserm U630, INSA-Lyon, Universite Lyon 1, Centre Leon Berard (France); Maigne, L; Perrot, Y [Laboratoire de Physique Corpusculaire, 24 Avenue des Landais, 63177 Aubiere Cedex (France); Schaart, D R [Delft University of Technology, Radiation Detection and Medical Imaging, Mekelweg 15, 2629 JB Delft (Netherlands); Pietrzyk, U, E-mail: buvat@imnc.in2p3.fr [Reseach Center Juelich, Institute of Neurosciences and Medicine and Department of Physics, University of Wuppertal (Germany)

2011-02-21

GATE (Geant4 Application for Emission Tomography) is a Monte Carlo simulation platform developed by the OpenGATE collaboration since 2001 and first publicly released in 2004. Dedicated to the modelling of planar scintigraphy, single photon emission computed tomography (SPECT) and positron emission tomography (PET) acquisitions, this platform is widely used to assist PET and SPECT research. A recent extension of this platform, released by the OpenGATE collaboration as GATE V6, now also enables modelling of x-ray computed tomography and radiation therapy experiments. This paper presents an overview of the main additions and improvements implemented in GATE since the publication of the initial GATE paper (Jan et al 2004 Phys. Med. Biol. 49 4543-61). This includes new models available in GATE to simulate optical and hadronic processes, novelties in modelling tracer, organ or detector motion, new options for speeding up GATE simulations, examples illustrating the use of GATE V6 in radiotherapy applications and CT simulations, and preliminary results regarding the validation of GATE V6 for radiation therapy applications. Upon completion of extensive validation studies, GATE is expected to become a valuable tool for simulations involving both radiotherapy and imaging.

Nanomechanical recognition of prognostic biomarker suPAR with DVD-ROM optical technology

DEFF Research Database (Denmark)

Bache, Michael; Bosco, Filippo; Brøgger, Anna Line

2013-01-01

In this work the use of a high-throughput nanomechanical detection system based on a DVD-ROM optical drive and cantilever sensors is presented for the detection of urokinase plasminogen activator receptor inflammatory biomarker (uPAR). Several large scale studies have linked elevated levels...

Float level switch for a nuclear power plant containment vessel

International Nuclear Information System (INIS)

Powell, J.G.

1993-01-01

This invention is a float level switch used to sense rise or drop in water level in a containment vessel of a nuclear power plant during a loss of coolant accident. The essential components of the device are a guide tube, a reed switch inside the guide tube, a float containing a magnetic portion that activates a reed switch, and metal-sheathed, ceramic-insulated conductors connecting the reed switch to a monitoring system outside the containment vessel. Special materials and special sealing techniques prevent failure of components and allow the float level switch to be connected to a monitoring system outside the containment vessel. 1 figures

Float level switch for a nuclear power plant containment vessel

Science.gov (United States)

Powell, James G.

1993-01-01

This invention is a float level switch used to sense rise or drop in water level in a containment vessel of a nuclear power plant during a loss of coolant accident. The essential components of the device are a guide tube, a reed switch inside the guide tube, a float containing a magnetic portion that activates a reed switch, and metal-sheathed, ceramic-insulated conductors connecting the reed switch to a monitoring system outside the containment vessel. Special materials and special sealing techniques prevent failure of components and allow the float level switch to be connected to a monitoring system outside the containment vessel.

Operating Experience with Nuclear Power Stations in Member States in 2013. 2014 Edition (CD-ROM)

International Nuclear Information System (INIS)

2014-07-01

This CD-ROM contains the 45th edition of the IAEA's series of annual reports on operating experience with nuclear power plants in Member States. It is a direct output from the IAEA's Power Reactor Information System (PRIS) and contains information on electricity production and overall performance of individual plants during 2013. In addition to annual information, the report contains a historical summary of performance during the lifetime of individual plants and figures illustrating worldwide performance of the nuclear industry. The CD-ROM contains also an overview of design characteristics and dashboards (not included into the web version) of all operating nuclear power plants worldwide

CLINICAL OUTCOME AFTER OPERATIVE TREATMENT IN FLOATING SHOULDER- A PROSPECTIVE STUDY

Directory of Open Access Journals (Sweden)

Nabarun Saha

2017-06-01

Full Text Available BACKGROUND The ‘floating shoulder’ is a rare injury consisting of ipsilateral fractures of the clavicle and glenoid neck. Although it may appear to be bony injury, studies suggest that ligamentous disruption associated with ipsilateral clavicle fracture and scapular neck fracture contributes to such entity. More commonly floating shoulder is defined as double disruption of the superior shoulder suspensory complex. Open reduction and internal fixation of both the fractures is the treatment of choice. We have made this study to assess clinical outcome after operative treatment of floating shoulder by DASH score. MATERIALS AND METHODS This is a study of 10 cases of floating shoulder injury operated in the same sitting by anterior approach for fracture clavicle and Judet’s posterior approach for scapula fracture from Jan 2014 to Oct 2016. All cases were assessed with DASH score at the end of six months. RESULTS Results of our study shows that majority of patients had excellent to good results with improvement in DASH score from 92.8 to 16.8 at final follow up. No major complications. All patients had radiological signs of union at the end of 1 year. CONCLUSION Surgical intervention should be considered for all floating shoulder injuries. open reduction and internal fixation not only increases stability but also to improves functional outcome of the patient. DASH score is an effective method to assess clinicofunctional outcome in post-operative cases of floating shoulder.

Differential Response of Floating and Submerged Leaves of Longleaf Pondweed to Silver Ions

Directory of Open Access Journals (Sweden)

Nisha Shabnam

2017-06-01

Full Text Available In this study, we have investigated variations in the potential of floating and submerged leaves of longleaf pondweed (Potamogeton nodosus to withstand silver ion (Ag+-toxicity. Both floating and submerged leaves changed clear colorless AgNO3 solutions to colloidal brown in the presence of light. Transmission electron microscopy revealed the presence of distinct crystalline Ag-nanoparticles (Ag-NPs in these brown solutions. Powder X-ray diffraction pattern showed that Ag-NPs were composed of Ag0 and Ag2O. Photosystem (PS II efficiency of leaves declined upon exposure to Ag+ with a significantly higher decline in the submerged leaves than in the floating leaves. Similarly, Ag+ treatment caused a significant reduction in the carboxylase activity of the ribulose bisphosphate carboxylase/oxygenase in leaves. The reduction in this carboxylase activity was significantly higher in the submerged than in the floating leaves. Ag+ treatment also resulted in a significant decline in the levels of non-enzymatic and enzymatic antioxidants; the decline was significantly lower in the floating than in submerged leaves. X-ray photoelectron spectroscopy revealed the presence of Ag2O in these leaves. Inductively coupled plasma mass spectrometry analysis revealed a three-fold higher Ag content in the submerged than in floating leaves. Our study demonstrates that floating leaves of longleaf pondweed have a superior potential to counter Ag+-toxicity compared with submerged leaves, which could be due to superior potential of floating leaves to reduce Ag+ to less/non-toxic Ag0/Ag2O-nanoparticles/nanocomplexes. We suggest that modulating the genotype of longleaf pondweed to bear higher proportion of floating leaves would help in cleaning fresh water bodies contaminated with ionic forms of heavy metals.

Investigation of Tank 241-AN-101 Floating Solids

Energy Technology Data Exchange (ETDEWEB)

Kraft, Douglas P. [Washington River Protection Solutions, LLC, Richland, VA (United States); Meznarich, H. K. [Washington River Protection Solutions, LLC, Richland, VA (United States)

2017-10-30

Tank 241-AN-101 is the receiver tank for retrieval of several C-Farms waste tanks, including Tanks 241-C-102 and 241-C-111. Tank 241 C 111 received first-cycle decontamination waste from the bismuth phosphate process and Plutonium and Uranium Extraction cladding waste, as well as hydraulic fluid. Three grab samples, 1AN-16-01, 1AN-16-01A, and 1AN-16-01B, were collected at the surface of Tank 241-AN-101 on April 25, 2016, after Tank 241-C-111 retrieval was completed. Floating solids were observed in the three grab samples in the 11A hot cell after the samples were received at the 222-S Laboratory. Routine chemical analyses, solid phase characterization on the floating and settled solids, semivolatile organic analysis mainly on the aqueous phase for identification of degradation products of hydraulic fluids were performed. Investigation of the floating solids is reported.

Multimedia CD-Rom on hydrogen and fuel cells. 2. rev. ed.; Die Multimedia CD-Rom zum Thema Wasserstoff und Brennstoffzellen

Energy Technology Data Exchange (ETDEWEB)

Anon.

2007-07-01

This CD-Rom contains well-presented information with informative illustrations, as well as a large download section with publications, reports, and presentations in.pdf form for in-depth studies. There is also a list of links to selected websites, with short explanations. [German] Die CD zum Thema ''Wasserstoff und Brennstoffzellen'' bietet sowohl gut gegliederte Informationen mit anschaulichen Bildern fuer die Lektuere am Monitor als auch eine grosse Download-Rubrik, in der zahlreiche Publikationen, Fachberichte, Praesentationen als PDF-Dateien abgelegt sind und fuers Studium bereitstehen. Ausserdem gibt es ein Link-Verzeichnis mit Verweisen und Erlaeuterungen zu ausgewaehlten Internet-Seiten.

Novel Quantum Dot Gate FETs and Nonvolatile Memories Using Lattice-Matched II-VI Gate Insulators

Science.gov (United States)

Jain, F. C.; Suarez, E.; Gogna, M.; Alamoody, F.; Butkiewicus, D.; Hohner, R.; Liaskas, T.; Karmakar, S.; Chan, P.-Y.; Miller, B.; Chandy, J.; Heller, E.

2009-08-01

This paper presents the successful use of ZnS/ZnMgS and other II-VI layers (lattice-matched or pseudomorphic) as high- k gate dielectrics in the fabrication of quantum dot (QD) gate Si field-effect transistors (FETs) and nonvolatile memory structures. Quantum dot gate FETs and nonvolatile memories have been fabricated in two basic configurations: (1) monodispersed cladded Ge nanocrystals (e.g., GeO x -cladded-Ge quantum dots) site-specifically self-assembled over the lattice-matched ZnMgS gate insulator in the channel region, and (2) ZnTe-ZnMgTe quantum dots formed by self-organization, using metalorganic chemical vapor-phase deposition (MOCVD), on ZnS-ZnMgS gate insulator layers grown epitaxially on Si substrates. Self-assembled GeO x -cladded Ge QD gate FETs, exhibiting three-state behavior, are also described. Preliminary results on InGaAs-on-InP FETs, using ZnMgSeTe/ZnSe gate insulator layers, are presented.

14 CFR 23.531 - Hull and main float takeoff condition.

Science.gov (United States)

2010-01-01

... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false Hull and main float takeoff condition. 23.531 Section 23.531 Aeronautics and Space FEDERAL AVIATION ADMINISTRATION, DEPARTMENT OF TRANSPORTATION... Water Loads § 23.531 Hull and main float takeoff condition. For the wing and its attachment to the hull...

14 CFR 25.531 - Hull and main float takeoff condition.

Science.gov (United States)

2010-01-01

... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false Hull and main float takeoff condition. 25... AIRCRAFT AIRWORTHINESS STANDARDS: TRANSPORT CATEGORY AIRPLANES Structure Water Loads § 25.531 Hull and main float takeoff condition. For the wing and its attachment to the hull or main float— (a) The aerodynamic...

Pitfalls in the Assessment, Analysis, and Interpretation of Routine Outcome Monitoring (ROM) Data : Results from an Outpatient Clinic for Integrative Mental Health

NARCIS (Netherlands)

Hoenders, Rogier H. J.; Bos, Elisabeth H.; Bartels-Velthuis, Agna A.; Vollbehr, Nina K.; van der Ploeg, Karen; de Jonge, Peter; de Jong, Joop T. V. M.

There is considerable debate about routine outcome monitoring (ROM) for scientific or benchmarking purposes. We discuss pitfalls associated with the assessment, analysis, and interpretation of ROM data, using data of 376 patients. 206 patients (55 %) completed one or more follow-up measurements.

New opening hours of the gates

CERN Multimedia

GS Department

2009-01-01

Please note the new opening hours of the gates as well as the intersites tunnel from the 19 May 2009: GATE A 7h - 19h GATE B 24h/24 GATE C 7h - 9h\t17h - 19h GATE D 8h - 12h\t13h - 16h GATE E 7h - 9h\t17h - 19h Prévessin 24h/24 The intersites tunnel will be opened from 7h30 to 18h non stop. GS-SEM Group Infrastructure and General Services Department

Wave energy absorption by a submerged air bag connected to a rigid float

DEFF Research Database (Denmark)

Kurniawan, Adi; Chaplin, J. R.; Hann, M. R.

2017-01-01

A new wave energy device features a submerged ballasted air bag connected at the top to a rigid float. Under wave action, the bag expands and contracts, creating a reciprocating air flow through a turbine between the bag and another volume housed within the float. Laboratory measurements are gene......A new wave energy device features a submerged ballasted air bag connected at the top to a rigid float. Under wave action, the bag expands and contracts, creating a reciprocating air flow through a turbine between the bag and another volume housed within the float. Laboratory measurements...

Provocarea Facebook pentru bibliotecile publice din România

Directory of Open Access Journals (Sweden)

Octavia-Luciana Madge

2014-01-01

Full Text Available Reţelele sociale şi-au câştigat rapid un loc în viaţa noastră şi în activitatea multor organizaţii şi instituţii publice şi private. La nivelul bibliotecilor, reţelele sociale şi-au demonstrat utilitatea şi rolul în calitate de instrumente de marketing pentru o mai bună comunicare cu utilizatorii. Bibliotecile publice din România au cunoscut în ultimul timp transformări mari în ceea ce priveşte modul de abordare a relaţiei cu utilizatorii şi îmbunătăţirea activităţii lor. Au lansat, de asemenea, o serie de noi servicii pentru a răspunde nevoilor comunităţii pe care o servesc şi pentru a atrage noi utilizatori. Implementarea şi utilizarea de noi aplicaţii precum reţelele de socializare online, mai exact Facebook, a fost una dintre aceste dezvoltări recente. Această lucrare analizează modul în care reţelele sociale sunt utilizate la nivelul bibliotecilor publice din România prin exemplul a trei biblioteci publice mari şi a modului în care aceste biblioteci îşi promovează serviciile prin intermediul reţelei Facebook.

Optical XOR gate

Science.gov (United States)

Vawter, G. Allen

2013-11-12

An optical XOR gate is formed as a photonic integrated circuit (PIC) from two sets of optical waveguide devices on a substrate, with each set of the optical waveguide devices including an electroabsorption modulator electrically connected in series with a waveguide photodetector. The optical XOR gate utilizes two digital optical inputs to generate an XOR function digital optical output. The optical XOR gate can be formed from III-V compound semiconductor layers which are epitaxially deposited on a III-V compound semiconductor substrate, and operates at a wavelength in the range of 0.8-2.0 .mu.m.

Intrinsic respiratory gating in small-animal CT

International Nuclear Information System (INIS)

Bartling, Soenke H.; Dinkel, Julien; Kauczor, Hans-Ulrich; Stiller, Wolfram; Semmler, Wolfhard; Grasruck, Michael; Madisch, Ijad; Gupta, Rajiv; Kiessling, Fabian

2008-01-01

Gating in small-animal CT imaging can compensate artefacts caused by physiological motion during scanning. However, all published gating approaches for small animals rely on additional hardware to derive the gating signals. In contrast, in this study a novel method of intrinsic respiratory gating of rodents was developed and tested for mice (n=5), rats (n=5) and rabbits (n=2) in a flat-panel cone-beam CT system. In a consensus read image quality was compared with that of non-gated and retrospective extrinsically gated scans performed using a pneumatic cushion. In comparison to non-gated images, image quality improved significantly using intrinsic and extrinsic gating. Delineation of diaphragm and lung structure improved in all animals. Image quality of intrinsically gated CT was judged to be equivalent to extrinsically gated ones. Additionally 4D datasets were calculated using both gating methods. Values for expiratory, inspiratory and tidal lung volumes determined with the two gating methods were comparable and correlated well with values known from the literature. We could show that intrinsic respiratory gating in rodents makes additional gating hardware and preparatory efforts superfluous. This method improves image quality and allows derivation of functional data. Therefore it bears the potential to find wide applications in small-animal CT imaging. (orig.)

Resident perceptions of the educational value of night float rotations.

Science.gov (United States)

Luks, Andrew M; Smith, C Scott; Robins, Lynne; Wipf, Joyce E

2010-07-01

Night float rotations are being increasingly used in the era of resident physician work-hour regulations, but their impact on resident education is not clear. Our objective was to clarify resident perceptions of the educational aspects of night float rotations. An anonymous survey of internal medicine residents at a university-based residency program was completed. Responses were received from 116 of 163 surveyed residents (71%). Residents attended less residents' report (0.10 +/- .43 vs. 2.70 + 0.93 sessions/week, peducational value of night float, sleep cycle adjustment issues, and impact on their personal lives, which correlated with resident evaluations from the regular program evaluation process. In free responses, residents commented that they liked the autonomy and opportunity to improve triage skills on these rotations and confirmed their negative opinions about the sleep-wake cycle and interference with personal lives. Internal medicine residents at a university-based program have negative opinions regarding the educational value of night float rotations. Further work is necessary to determine whether problems exist across programs and specialties.

Effect analysis of geometric parameters of floating raft on isolation performance

Directory of Open Access Journals (Sweden)

LI Shangda

2017-12-01

Full Text Available [Objectives] This paper focuses on the effects of the geometric parameters of a floating raft on isolation performance.[Methods] Based on the idea that the weight of a floating raft remains constant, a parametric finite element model is established using geometric parameters, and the effects of the geometric parameters when isolation performance is measured by vibration level difference are discussed.[Results] The effects of the geometric parameters of a floating raft on isolation performance are mainly reflected in the middle and high frequency areas. The most important geometric parameters which have an impact on isolation performance are the raft's height, length to width ratio and number of ribs. Adjusting the geometric parameters of the raft is one effective way to avoid the vibration frequency of mechanical equipment.[Conclusions] This paper has some practical value for the engineering design of floating raft isolation systems.

Signatures of Mechanosensitive Gating.

Science.gov (United States)

Morris, Richard G

2017-01-10

The question of how mechanically gated membrane channels open and close is notoriously difficult to address, especially if the protein structure is not available. This perspective highlights the relevance of micropipette-aspirated single-particle tracking-used to obtain a channel's diffusion coefficient, D, as a function of applied membrane tension, σ-as an indirect assay for determining functional behavior in mechanosensitive channels. While ensuring that the protein remains integral to the membrane, such methods can be used to identify not only the gating mechanism of a protein, but also associated physical moduli, such as torsional and dilational rigidity, which correspond to the protein's effective shape change. As an example, three distinct D-versus-σ "signatures" are calculated, corresponding to gating by dilation, gating by tilt, and gating by a combination of both dilation and tilt. Both advantages and disadvantages of the approach are discussed. Copyright © 2017 Biophysical Society. Published by Elsevier Inc. All rights reserved.

The New York Trade Publishers and CD-ROM: Where Are They Heading?

Science.gov (United States)

Newmark, Eileen

1994-01-01

Discusses the strategies top trade publishers, including Putnam New Media, Paramount Communications, Random House, Penguin USA, and Reader's Digest, are taking toward CD-ROM publishing. Strategies include purchasing electronic media companies; setting up an independent business; and building a new media business by integrating new efforts into the…

14 CFR 23.527 - Hull and main float load factors.

Science.gov (United States)

2010-01-01

... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false Hull and main float load factors. 23.527... Water Loads § 23.527 Hull and main float load factors. (a) Water reaction load factors nw must be...=seaplane landing weight in pounds. (6) K1=empirical hull station weighing factor, in accordance with figure...

Quantum gate decomposition algorithms.

Energy Technology Data Exchange (ETDEWEB)

Slepoy, Alexander

2006-07-01

Quantum computing algorithms can be conveniently expressed in a format of a quantum logical circuits. Such circuits consist of sequential coupled operations, termed ''quantum gates'', or quantum analogs of bits called qubits. We review a recently proposed method [1] for constructing general ''quantum gates'' operating on an qubits, as composed of a sequence of generic elementary ''gates''.

Lossy/Lossless Floating/Grounded Inductance Simulation Using One DDCC

Directory of Open Access Journals (Sweden)

M. A. Ibrahim

2012-04-01

Full Text Available In this work, we present new topologies for realizing one lossless grounded inductor and two floating, one lossless and one lossy, inductors employing a single differential difference current conveyor (DDCC and a minimum number of passive components, two resistors, and one grounded capacitor. The floating inductors are based on ordinary dual-output differential difference current conveyor (DO-DDCC while the grounded lossless inductor is based one a modified dual-output differential difference current conveyor (MDO-DDCC. The proposed lossless floating inductor is obtained from the lossy one by employing a negative impedance converter (NIC. The non-ideality effects of the active element on the simulated inductors are investigated. To demonstrate the performance of the proposed grounded inductance simulator as an example, it is used to construct a parallel resonant circuit. SPICE simulation results are given to confirm the theoretical analysis.

Optimal Control of a Ballast-Stabilized Floating Wind Turbine

DEFF Research Database (Denmark)

Christiansen, Søren; Knudsen, Torben; Bak, Thomas

2011-01-01

Offshore wind energy capitalizes on the higher and less turbulent wind speeds at sea. The use of floating structures for deeper waters is being explored. The control objective is a tradeoff between power capture and fatigue, especially that produced by the oscillations caused by the reduced...... structural stiffness of a floating installation in combination with a coupling between the fore–aft motion of the tower and the blade pitch. To address this problem, the present paper models a ballast-stabilized floating wind turbine, and suggests a linear quadratic regulator (LQR) in combination with a wind...... estimator and a state observer. The results are simulated using aero elastic code and analysed in terms of damage equivalent loads. When compared to a baseline controller, this controller clearly demonstrates better generator speed and power tracking while reducing fatigue loads....

Genetics Home Reference: Floating-Harbor syndrome

Science.gov (United States)

... Patton MA, Hurst J, Donnai D, McKeown CM, Cole T, Goodship J. Floating-Harbor syndrome. J Med ... medicine? What is newborn screening? New Pages Lyme disease Fibromyalgia White-Sutton syndrome All New & Updated Pages ...

Dynamic analysis of maritime gasbag-type floating bridge subjected to moving loads

Directory of Open Access Journals (Sweden)

Huan-huan Wang

2016-03-01

Full Text Available This paper studied the dynamic response of a new gasbag-type floating bridge under the effect of a moving load. The arbitrary Lagrangian-Eulerian (ALE method was used to simulate the movement of seawater and air, and the penalty-based method was used to study the coupling between gasbags and fluid. A three-dimensional finite element model of the floating bridge was established, and the numerical model was verified by comparing with the experimental results. In order to prevent resonance, the natural frequencies and flexural mode shapes were analyzed. Based on the initial state analysis, the dynamic responses of the floating bridge subjected to different moving loads were investigated. Vertical displacements and radial deformations of gasbags under different loads were compared, and principal stress distributions of gasbags were researched while driving. The hinge forces between adjacent modules were calculated to ensure the connection strength. Besides, the floating bridge under wave impacting was analyzed. Those results can provide references for the analysis and design of this new floating bridge.

Modeling of 4H—SiC multi-floating-junction Schottky barrier diode

International Nuclear Information System (INIS)

Hong-Bin, Pu; Lin, Cao; Zhi-Ming, Chen; Jie, Ren; Ya-Gong, Nan

2010-01-01

This paper develops a new and easy to implement analytical model for the specific on-resistance and electric field distribution along the critical path for 4H—SiC multi-floating junction Schottky barrier diode. Considering the charge compensation effects by the multilayer of buried opposite doped regions, it improves the breakdown voltage a lot in comparison with conventional one with the same on-resistance. The forward resistance of the floating junction Schottky barrier diode consists of several components and the electric field can be understood with superposition concept, both are consistent with MEDICI simulation results. Moreover, device parameters are optimized and the analyses show that in comparison with one layer floating junction, multilayer of floating junction layer is an effective way to increase the device performance when specific resistance and the breakdown voltage are traded off. The results show that the specific resistance increases 3.2 mΩ·cm 2 and breakdown voltage increases 422 V with an additional floating junction for the given structure. (condensed matter: electronic structure, electrical, magnetic, and optical properties)

Wake Influence on Dynamic Load Characteristics of Offshore Floating Wind Turbines

DEFF Research Database (Denmark)

Jeon, Minu; Lee, Soogab; Kim, Taeseong

2016-01-01

Because the flow conditions of an offshore floating wind turbine and onshore fixed wind turbine differ, it is debatable whether the aerodynamic load predictions of an offshore floating wind turbine using the conventional blade-element momentum theory, which does not consider the dynamic wake effe...

Lagrangian current measurements and large-scale long-term dispersion rates (Sofar float experiment)

International Nuclear Information System (INIS)

Gurbutt, F.A.

1984-01-01

Activity entering the water from a deep-sea disposal of radioactive waste package will be dispersed through the ocean both by the long-term circulation pattern and the eddy (mixing) motions. Sofar floats are thought to be the most cost-effective way of obtaining direct information on the circulation over a few years and the only way to obtain information, in the Lagrangian framework, on the statistics of the eddy movements. The Sofar float experiment seeks to answer questions including: (a) What is the magnitude of space and time variability of the horizontal eddy kinetic energy in the eastern bassin and is it consistent with that found in the western basin of the North Atlantic. (b) Is the deep flow inferred from incoherent arrays of moored current meters correct. The report covers the preparation stage for the Sofar float experiment whick takes place from autumn 1984 to 1986. It describes the recent results from the western North Atlantic, the design of the new deep Sofar float, the testing of the float including the range at which these new floats can be heard, the experimental design and expected results

On the proposed second law paradox in a nonzero floating potential

International Nuclear Information System (INIS)

Cruden, Brett A.

2001-01-01

A second law paradox was previously proposed for a plasma contained within an infinite blackbody. The proposed second law paradox was dependent on the plasma having a nonzero floating potential [D. P. Sheehan and J. D. Means, Phys. Plasmas 5, 2469 (1998)]. This work demonstrates that a nonzero floating potential is indicative of some energy contained within the plasma that can be withdrawn from the plasma without violation of the second law. Furthermore, it is shown from the probe theory that the plasma in this hypothetical configuration must have a floating potential of zero at steady state

Preparation and Characterization of a Gastric Floating Dosage Form of Capecitabine

Directory of Open Access Journals (Sweden)

Ehsan Taghizadeh Davoudi

2013-01-01

Full Text Available Gastrointestinal disturbances, such as nausea and vomiting, are considered amongst the main adverse effects associated with oral anticancer drugs due to their fast release in the gastrointestinal tract (GIT. Sustained release formulations with proper release profiles can overcome some side effects of conventional formulations. The current study was designed to prepare sustained release tablets of Capecitabine, which is approved by the Food and Drug Administration (FDA for the treatment of advanced breast cancer, using hydroxypropyl methylcellulose (HPMC, carbomer934P, sodium alginate, and sodium bicarbonate. Tablets were prepared using the wet granulation method and characterized such that floating lag time, total floating time, hardness, friability, drug content, weight uniformity, and in vitro drug release were investigated. The sustained release tablets showed good hardness and passed the friability test. The tablets’ floating lag time was determined to be 30–200 seconds, and it floated more than 24 hours and released the drug for 24 hours. Then, the stability test was done and compared with the initial samples. In conclusion, by adjusting the right ratios of the excipients including release-retarding gel-forming polymers like HPMC K4M, Na alginate, carbomer934P, and sodium bicarbonate, sustained release Capecitabine floating tablet was formulated.

Preparation and characterization of a gastric floating dosage form of capecitabine.

Science.gov (United States)

Taghizadeh Davoudi, Ehsan; Ibrahim Noordin, Mohamed; Kadivar, Ali; Kamalidehghan, Behnam; Farjam, Abdoreza Soleimani; Akbari Javar, Hamid

2013-01-01

Gastrointestinal disturbances, such as nausea and vomiting, are considered amongst the main adverse effects associated with oral anticancer drugs due to their fast release in the gastrointestinal tract (GIT). Sustained release formulations with proper release profiles can overcome some side effects of conventional formulations. The current study was designed to prepare sustained release tablets of Capecitabine, which is approved by the Food and Drug Administration (FDA) for the treatment of advanced breast cancer, using hydroxypropyl methylcellulose (HPMC), carbomer934P, sodium alginate, and sodium bicarbonate. Tablets were prepared using the wet granulation method and characterized such that floating lag time, total floating time, hardness, friability, drug content, weight uniformity, and in vitro drug release were investigated. The sustained release tablets showed good hardness and passed the friability test. The tablets' floating lag time was determined to be 30-200 seconds, and it floated more than 24 hours and released the drug for 24 hours. Then, the stability test was done and compared with the initial samples. In conclusion, by adjusting the right ratios of the excipients including release-retarding gel-forming polymers like HPMC K4M, Na alginate, carbomer934P, and sodium bicarbonate, sustained release Capecitabine floating tablet was formulated.

Self-gated fat-suppressed cardiac cine MRI.

Science.gov (United States)

Ingle, R Reeve; Santos, Juan M; Overall, William R; McConnell, Michael V; Hu, Bob S; Nishimura, Dwight G

2015-05-01

To develop a self-gated alternating repetition time balanced steady-state free precession (ATR-SSFP) pulse sequence for fat-suppressed cardiac cine imaging. Cardiac gating is computed retrospectively using acquired magnetic resonance self-gating data, enabling cine imaging without the need for electrocardiogram (ECG) gating. Modification of the slice-select rephasing gradients of an ATR-SSFP sequence enables the acquisition of a one-dimensional self-gating readout during the unused short repetition time (TR). Self-gating readouts are acquired during every TR of segmented, breath-held cardiac scans. A template-matching algorithm is designed to compute cardiac trigger points from the self-gating signals, and these trigger points are used for retrospective cine reconstruction. The proposed approach is compared with ECG-gated ATR-SSFP and balanced steady-state free precession in 10 volunteers and five patients. The difference of ECG and self-gating trigger times has a variability of 13 ± 11 ms (mean ± SD). Qualitative reviewer scoring and ranking indicate no statistically significant differences (P > 0.05) between self-gated and ECG-gated ATR-SSFP images. Quantitative blood-myocardial border sharpness is not significantly different among self-gated ATR-SSFP ( 0.61±0.15 mm -1), ECG-gated ATR-SSFP ( 0.61±0.15 mm -1), or conventional ECG-gated balanced steady-state free precession cine MRI ( 0.59±0.15 mm -1). The proposed self-gated ATR-SSFP sequence enables fat-suppressed cardiac cine imaging at 1.5 T without the need for ECG gating and without decreasing the imaging efficiency of ATR-SSFP. © 2014 Wiley Periodicals, Inc.

Şcoli şi biserici româneşti din Peninsula Balcanică 1864-1948. Documente de arhivă

Directory of Open Access Journals (Sweden)

Adina Berciu-Drăghicescu

2006-01-01

Full Text Available Articolul de faţă privind şcolile şi bisericile româneşti din Peninsula Balcanică în perioada 1918-1948 este realizat pe baza unor documente identificate în fonduri păstrate la Arhivele Diplomatice ale Ministerului Afacerilor Externe şi la Direcţia Arhivelor Naţioanle Istorice Centrale din Bucureşti. Au fost studiate şi selectate documente de cea mai mare semnificaţie în scopul prezentării evoluţiei situaţiei şcolilor şi bisericilor comunităţilor româneşti situate la sud de Dunăre începând cu anul 1864, când a fost înfiinţată prima şcoală în Târnova (Macedonia şi până în 1948 când statul român a abandonat acţiunea iniţiată de conducătorul Al. Ioan Cuza. Articolul prezintă această situaţie, foarte dramatică, a comunităţilor româneşti din Balcani pe baza documentelor de arhivă.

Factors Affecting Pre-Service TESOL Teachers' Attitudes towards Using CD-ROM Dictionary

Science.gov (United States)

Issa, Jinan Hatem; Jamil, Hazri

2011-01-01

Rapid technological advances in communication technologies and computational power are altering the nature of knowledge, skills, talents and the know-how of individuals. A CD-ROM dictionary is an interesting and effective teaching tool, which captures pre-service teachers' interest and does much more than just translates especially with the…

Control electronic platform based on floating-point DSP and FPGA for a NPC multilevel back-to-back converter

Energy Technology Data Exchange (ETDEWEB)

Rodriguez, Francisco J.; Cobreces, Santiago; Bueno, Emilio J.; Hernandez, Alvaro; Mateos, Raul; Espinosa, Felipe [Department of Electronics, University of Alcala, Alcala de Henares, Madrid (Spain)

2008-09-15

Modern energy concepts as Distributed Power Generation are changing the appearance of electric distribution and transmission and challenging power electronics researchers, which try to develop new solutions of electronic controllers. The aim is to enable the implementation of new and more complex control algorithms to verify the last standards related to the grid energy quality for new power converters, and, also, for equipments which nowadays are operating. This paper presents the design, implementation and test of a novel real-time controller for a Neutral Point Clamped (NPC) (three-level) multilevel converter based on a floating-point Digital Signal Processor (DSP) and on a Field-Programmable Gate Array (FPGA), by operating in a cooperative way. Although the proposed system can be readily applied to any power electronic application, in this work, it is focused on the next system: a 150 kVA back-to-back three-level NPC Voltage Source Converter (VSC) for wind power applications. (author)

Advanced grammar in use a self-study reference and practice book for advanced students of English : with answers and CD-ROM

CERN Document Server

Hewings, Martin

2013-01-01

An updated version of the highly successful Advanced Grammar in Use. This third edition, with answers and CD-ROM, is ideal for self-study. The book contains 100 units of grammar reference and practice materials, with illustrations in full colour and a user-friendly layout. It is ideal for learners preparing for the Cambridge Advanced, Proficiency or IELTS examinations, and is informed by the Cambridge International Corpus, which ensures the language is authentic and up-to-date. The CD-ROM includes 200 interactive exercises to reinforce the language learned in the book, plus customised tests and audio recordings to accompany the main exercises. Versions without answers and without the CD-ROM are available to purchase separately.

Motion Performance and Mooring System of a Floating Offshore Wind Turbine

Institute of Scientific and Technical Information of China (English)

Jing Zhao; Liang Zhang; Haitao Wu

2012-01-01

The development of offshore wind farms was originally carried out in shallow water areas with fixed (seabed mounted) structures.However,countries with limited shallow water areas require innovative floating platforms to deploy wind turbines offshore in order to harness wind energy to generate electricity in deep seas.The performances of motion and mooring system dynamics are vital to designing a cost effective and durable floating platform.This paper describes a numerical model to simulate dynamic behavior of a new semi-submersible type floating offshore wind turbine (FOWT) system.The wind turbine was modeled as a wind block with a certain thrust coefficient,and the hydrodynamics and mooring system dynamics of the platform were calculated by SESAM software.The effect of change in environmental conditions on the dynamic response of the system under wave and wind loading was examined.The results indicate that the semi-submersible concept has excellent performance and SESAM could be an effective tool for floating wind turbine design and analysis.

Motion performance and mooring system of a floating offshore wind turbine

Science.gov (United States)

Zhao, Jing; Zhang, Liang; Wu, Haitao

2012-09-01

The development of offshore wind farms was originally carried out in shallow water areas with fixed (seabed mounted) structures. However, countries with limited shallow water areas require innovative floating platforms to deploy wind turbines offshore in order to harness wind energy to generate electricity in deep seas. The performances of motion and mooring system dynamics are vital to designing a cost effective and durable floating platform. This paper describes a numerical model to simulate dynamic behavior of a new semi-submersible type floating offshore wind turbine (FOWT) system. The wind turbine was modeled as a wind block with a certain thrust coefficient, and the hydrodynamics and mooring system dynamics of the platform were calculated by SESAM software. The effect of change in environmental conditions on the dynamic response of the system under wave and wind loading was examined. The results indicate that the semi-submersible concept has excellent performance and SESAM could be an effective tool for floating wind turbine design and analysis.

Guide Structures in CD-ROM Dictionaries, with Specific Reference to the EWED and the ELHAT

Directory of Open Access Journals (Sweden)

Philip Louw

2011-10-01

Full Text Available

macro- and microstructural information. In order to evaluate the methods which lexicographers employ to improve dictionary accessibility, the concept of guide structures was introduced by Hausmann and Wiegand (1989. Since the appearance of that article, various academics have written articles and read papers on guide structures in print dictionaries, but few studies have focussed on the tremendous potential of guide structures in electronic dictionaries. In this article it will be shown that electronic dictionaries add dimensions to the implementation of guide structures not possible in print versions. The role of two of the guide structures in the transfer of infonnation in CD-ROM dictionaries will be discussed. The access and mediostructures of the Microsoft Encarta World English Dictionary and the Elektroniese Handwoordeboek van die Afrikaanse Taal will be analysed and critically evaluated to illustrate the advantages of electronic dictionaries over print dictionaries and the urgent need for metalexicographical discussion of this publication medium.

Keywords: ACCESS STRUCTURE; ACTIVE CROSS-REFERENCES; CD-ROM DICTIONARY; DICTIONARY ACCESSIBILITY; ENCYCLOPAEDIC DICTIONARY; GUIDE STRUCTURES; INNER ACCESS STRUCTURE; INNER SEARCH PATH; INTERNET; MEDIOSTRUCTURE; MULTIMEDIA; OUTER ACCESS STRUCTURE; OUTER SEARCH PATH; PASSIVE CROSSREFERENCING; USER-FRIENDLINESS

Opsomming: Gidsstrukture in CD-ROM-woordeboeke, met spesifieke verwysingna EWED en ELHA T. Die sukses van modeme woordeboeke hang grootliles af vandie toeganklikheid van hulle makro- en mikrostrukturele inligting. Hausmann en Wiegand (1989het die konsep van gidsstrukture ingevoer om die metodes te evalueer wat leksikograwe gebruikom woordeboektoeganklikheid Ie verbeter. Sedert hierdie artikel verskyn het, het verskeie akademic:i artikels gepubliseer en referate gelewer oor gidsstrukture in gedrukte woordeboeke, maarmin studies het gefokus op die geweldige potensiaal van

Low band-to-band tunnelling and gate tunnelling current in novel nanoscale double-gate architecture: simulations and investigation

International Nuclear Information System (INIS)

Datta, Deepanjan; Ganguly, Samiran; Dasgupta, S

2007-01-01

Large band-to-band tunnelling (BTBT) and gate leakage current can limit scalability of nanoscale devices. In this paper, we have proposed a novel nanoscale parallel connected heteromaterial double gate (PCHEM-DG) architecture with triple metal gate which significantly suppress BTBT leakage, making it efficient for low power design in the sub-10 nm regime. We have also proposed a triple gate device with p + poly-n + poly-p + poly gate which has substantially low gate leakage over symmetric DG MOSFET. Simulations are performed using a 2D Poisson-Schroedinger simulator and verified with a 2D device simulator ATLAS. We conclude that, due to intrinsic body doping, negligible gate leakage, suppressed BTBT over symmetric DG devices, metal gate (MG) PCHEM-DG MOSFET is efficient for low power circuit design in the nanometre regime

Water Pressure Distribution on a Twin-Float Seaplane

Science.gov (United States)

Thompson, F L

1930-01-01

This is the second of a series of investigations to determine water pressure distribution on various types of seaplane floats and hulls, and was conducted on a twin-float seaplane. It consisted of measuring water pressures and accelerations on a TS-1 seaplane during numerous landing and taxiing maneuvers at various speeds and angles. The results show that water pressures as great as 10 lbs. per sq. in.may occur at the step in various maneuvers and that pressures of approximately the same magnitude occur at the stern and near the bow in hard pancake landings with the stern way down. At the other parts of the float the pressures are less and are usually zero or slightly negative for some distance abaft the step. A maximum negative pressure of 0.87 lb. Per square inch was measured immediately abaft the step. The maximum positive pressures have a duration of approximately one-twentieth to one-hundredth second at any given location and are distributed over a very limited area at any particular instant.

Visualization of neonatal coronary arteries on multidetector row CT: ECG-gated versus non-ECG-gated technique

International Nuclear Information System (INIS)

Tsai, I.C.; Lee, Tain; Chen, Min-Chi; Fu, Yun-Ching; Jan, Sheng-Lin; Wang, Chung-Chi; Chang, Yen

2007-01-01

Multidetector CT (MDCT) seems to be a promising tool for detection of neonatal coronary arteries, but whether the ECG-gated or non-ECG-gated technique should be used has not been established. To compare the detection rate and image quality of neonatal coronary arteries on MDCT using ECG-gated and non-ECG-gated techniques. Twelve neonates with complex congenital heart disease were included. The CT scan was acquired using an ECG-gated technique, and the most quiescent phase of the RR interval was selected to represent the ECG-gated images. The raw data were then reconstructed without the ECG signal to obtain non-ECG-gated images. The detection rate and image quality of nine coronary artery segments in the two sets of images were then compared. A two-tailed paired t test was used with P values <0.05 considered as statistically significant. In all coronary segments the ECG-gated technique had a better detection rate and produced images of better quality. The difference between the two techniques ranged from 25% in the left main coronary artery to 100% in the distal right coronary artery. For neonates referred for MDCT, if evaluation of coronary artery anatomy is important for the clinical management or surgical planning, the ECG-gated technique should be used because it can reliably detect the coronary arteries. (orig.)

FLOAT - development of new flexible UHPC. Final report. [Ultra High Performance Fibre Reinforced Concrete

Energy Technology Data Exchange (ETDEWEB)

NONE

2012-11-01

The current project is a preliminary study intended to clarify the background and give a better basis for an evaluation of the risks and possible rewards of funding a full project with the overall purpose of developing and testing a new concept for wave energy floaters, made of Ultra High Performance Fibre Reinforced Concrete (UHPC), as an enabling technology for the establishment of competitive wave energy production (FLOAT). As an initial step for this preliminary study of FLOAT an investigation has been undertaken in relation to preliminary design of 2 types of floaters, essential properties of UHPFRC - and identification of necessary developments, compilation of existing data from off shore applications and analysis of effect on Cost Of Energy. Preliminary float design and economical considerations - is a theoretical and numerical study including preliminary float designs and cost estimates. It aims at making a first comparison between the different materials options for DEXA and Wave Star floats and giving a first judgement about the suitability of CRC concrete. This is done through a qualitative assessment of pros and cons of different materials for both types of floats and a design study of the Dexa Wave float. It is concluded that the requirements for the Dexa Wave float are so that CRC is not able to compete with conventional concrete for the best and most cost effective solution. The good durability (leading to low maintenance costs), the mechanical properties and the ductility of CRC are not important enough to offset the increased cost for this float. For Wave Star on the other hand, there are significant advantages in using CRC as the only other option in this case is fibre glass, which is a much more expensive product. An investigation was made of methods of optimizing the properties of CRC - customizing them for particular applications in WEC's. The method of optimization has been to change the types of fibres in the mix, and it is demonstrated

Single-Walled Carbon-Nanotubes-Based Organic Memory Structures

Directory of Open Access Journals (Sweden)

Sundes Fakher

2016-09-01

Full Text Available The electrical behaviour of organic memory structures, based on single-walled carbon-nanotubes (SWCNTs, metal–insulator–semiconductor (MIS and thin film transistor (TFT structures, using poly(methyl methacrylate (PMMA as the gate dielectric, are reported. The drain and source electrodes were fabricated by evaporating 50 nm gold, and the gate electrode was made from 50 nm-evaporated aluminium on a clean glass substrate. Thin films of SWCNTs, embedded within the insulating layer, were used as the floating gate. SWCNTs-based memory devices exhibited clear hysteresis in their electrical characteristics (capacitance–voltage (C–V for MIS structures, as well as output and transfer characteristics for transistors. Both structures were shown to produce reliable and large memory windows by virtue of high capacity and reduced charge leakage. The hysteresis in the output and transfer characteristics, the shifts in the threshold voltage of the transfer characteristics, and the flat-band voltage shift in the MIS structures were attributed to the charging and discharging of the SWCNTs floating gate. Under an appropriate gate bias (1 s pulses, the floating gate is charged and discharged, resulting in significant threshold voltage shifts. Pulses as low as 1 V resulted in clear write and erase states.

Mathematical modeling of large floating roof reservoir temperature arena

Directory of Open Access Journals (Sweden)

Liu Yang

2018-03-01

Full Text Available The current study is a simplification of related components of large floating roof tank and modeling for three dimensional temperature field of large floating roof tank. The heat transfer involves its transfer between the hot fluid in the oil tank, between the hot fluid and the tank wall and between the tank wall and the external environment. The mathematical model of heat transfer and flow of oil in the tank simulates the temperature field of oil in tank. Oil temperature field of large floating roof tank is obtained by numerical simulation, map the curve of central temperature dynamics with time and analyze axial and radial temperature of storage tank. It determines the distribution of low temperature storage tank location based on the thickness of the reservoir temperature. Finally, it compared the calculated results and the field test data; eventually validated the calculated results based on the experimental results.

Cascade Analysis of a Floating Wind Turbine Rotor

International Nuclear Information System (INIS)

Eliassen, Lene; Jakobsen, Jasna B; Knauer, Andreas; Nielsen, Finn Gunnar

2014-01-01

Mounting a wind turbine on a floating foundation introduces more complexity to the aerodynamic loading. The floater motion contains a wide range of frequencies. To study some of the basic dynamic load effect on the blades due to these motions, a two-dimensional cascade approach, combined with a potential vortex method, is used. This is an alternative method to study the aeroelastic behavior of wind turbines that is different from the traditional blade element momentum method. The analysis tool demands little computational power relative to a full three dimensional vortex method, and can handle unsteady flows. When using the cascade plane, a ''cut'' is made at a section of the wind turbine blade. The flow is viewed parallel to the blade axis at this cut. The cascade model is commonly used for analysis of turbo machineries. Due to the simplicity of the code it requires little computational resources, however it has limitations in its validity. It can only handle two-dimensional potential flow, i.e. including neither three-dimensional effects, such as the tip loss effect, nor boundary layers and stall effects are modeled. The computational tool can however be valuable in the overall analysis of floating wind turbines, and evaluation of the rotor control system. A check of the validity of the vortex panel code using an airfoil profile is performed, comparing the variation of the lift force, to the theoretically derived Wagner function. To analyse the floating wind turbine, a floating structure with hub height 90 m is chosen. An axial motion of the rotor is considered

Enhancement of Biomass and Lipid Productivities of Water Surface-Floating Microalgae by Chemical Mutagenesis.

Science.gov (United States)

Nojima, Daisuke; Ishizuka, Yuki; Muto, Masaki; Ujiro, Asuka; Kodama, Fumito; Yoshino, Tomoko; Maeda, Yoshiaki; Matsunaga, Tadashi; Tanaka, Tsuyoshi

2017-05-27

Water surface-floating microalgae have great potential for biofuel applications due to the ease of the harvesting process, which is one of the most problematic steps in conventional microalgal biofuel production. We have collected promising water surface-floating microalgae and characterized their capacity for biomass and lipid production. In this study, we performed chemical mutagenesis of two water surface-floating microalgae to elevate productivity. Floating microalgal strains AVFF007 and FFG039 (tentatively identified as Botryosphaerella sp. and Chlorococcum sp., respectively) were exposed to ethyl methane sulfonate (EMS) or 1-methyl-3-nitro-1-nitrosoguanidine (MNNG), and pale green mutants (PMs) were obtained. The most promising FFG039 PM formed robust biofilms on the surface of the culture medium, similar to those formed by wild type strains, and it exhibited 1.7-fold and 1.9-fold higher biomass and lipid productivities than those of the wild type. This study indicates that the chemical mutation strategy improves the lipid productivity of water surface-floating microalgae without inhibiting biofilm formation and floating ability.

Occupational Analysis Products: Space Systems Operations - AFSC 1C6X1 (CD-ROM)

National Research Council Canada - National Science Library

Boerstler, Robert E

2004-01-01

...: 1 CD-ROM; 4 3/4 in.; 30.4 MB. SYSTEMS DETAIL NOTE: ABSTRACT: The Space Systems Operations career ladder was surveyed to obtain current task and equipment data for use in evaluating current training programs...

Low band-to-band tunnelling and gate tunnelling current in novel nanoscale double-gate architecture: simulations and investigation

Energy Technology Data Exchange (ETDEWEB)

Datta, Deepanjan [Department of Electrical and Computer Engineering, Purdue University, West Lafayette, IN 47906 (United States); Ganguly, Samiran [Department of Electronics Engineering, Indian School of Mines, Dhanbad-826004 (India); Dasgupta, S [Department of Electronics and Computer Engineering, Indian Institute of Technology, Roorkee-247667 (India)

2007-05-30

Large band-to-band tunnelling (BTBT) and gate leakage current can limit scalability of nanoscale devices. In this paper, we have proposed a novel nanoscale parallel connected heteromaterial double gate (PCHEM-DG) architecture with triple metal gate which significantly suppress BTBT leakage, making it efficient for low power design in the sub-10 nm regime. We have also proposed a triple gate device with p{sup +} poly-n{sup +} poly-p{sup +} poly gate which has substantially low gate leakage over symmetric DG MOSFET. Simulations are performed using a 2D Poisson-Schroedinger simulator and verified with a 2D device simulator ATLAS. We conclude that, due to intrinsic body doping, negligible gate leakage, suppressed BTBT over symmetric DG devices, metal gate (MG) PCHEM-DG MOSFET is efficient for low power circuit design in the nanometre regime.

Estimating Wind and Wave Induced Forces On a Floating Wind Turbine

DEFF Research Database (Denmark)

Henriksen, Lars Christian; Natarajan, Anand; Kim, Taeseong

2013-01-01

-principles derived state space model of the floating wind turbine. The ability to estimate aero- and hydrodynamic states could prove crucial for the performance of model-based control methods applied on floating wind turbines. Furthermore, two types of water kinematics have been compared two determine whether......In this work, the basic model for a spar buoy floating wind turbine [1], used by an extended Kalman filter, is presented and results concerning wind speed and wave force estimations are shown. The wind speed and aerodynamic forces are estimated using an extended Kalman filter based on a first...... or not linear and nonlinear water kinematics lead to significantly different loads....

Sliding-gate valve for use with abrasive materials

Science.gov (United States)

Ayers, Jr., William J.; Carter, Charles R.; Griffith, Richard A.; Loomis, Richard B.; Notestein, John E.

1985-01-01

The invention is a flow and pressure-sealing valve for use with abrasive solids. The valve embodies special features which provide for long, reliable operating lifetimes in solids-handling service. The valve includes upper and lower transversely slidable gates, contained in separate chambers. The upper gate provides a solids-flow control function, whereas the lower gate provides a pressure-sealing function. The lower gate is supported by means for (a) lifting that gate into sealing engagement with its seat when the gate is in its open and closed positions and (b) lowering the gate out of contact with its seat to permit abrasion-free transit of the gate between its open and closed positions. When closed, the upper gate isolates the lower gate from the solids. Because of this shielding action, the sealing surface of the lower gate is not exposed to solids during transit or when it is being lifted or lowered. The chamber containing the lower gate normally is pressurized slightly, and a sweep gas is directed inwardly across the lower-gate sealing surface during the vertical translation of the gate.

Plant traits and environment: floating leaf blade production and turnover of waterlilies.

Science.gov (United States)

Klok, Peter F; van der Velde, Gerard

2017-01-01

Floating leaf blades of waterlilies fulfill several functions in wetland ecosystems by production, decomposition and turnover as well as exchange processes. Production and turnover rates of floating leaf blades of three waterlily species, Nuphar lutea (L.) Sm., Nymphaea alba L. and Nymphaea candida Presl, were studied in three freshwater bodies, differing in trophic status, pH and alkalinity. Length and percentages of leaf loss of marked leaf blades were measured weekly during the growing season. Area and biomass were calculated based on leaf length and were used to calculate the turnover rate of floating leaf blades. Seasonal changes in floating leaf production showed that values decreased in the order: Nymphaea alba , Nuphar lutea , Nymphaea candida . The highest production was reached for Nuphar lutea and Nymphaea alba in alkaline, eutrophic water bodies. The production per leaf was relatively high for both species in the acid water body. Nymphaea candida showed a very short vegetation period and low turnover rates. The ratio Total potential leaf biomass/Maximum potential leaf biomass (P/B max ) of the three species ranged from 1.35-2.25. The ratio Vegetation period (Period with floating leaves)/Mean leaf life span ranged from 2.94-4.63, the ratio Growth period (Period with appearance of new floating leaves)/Vegetation period from 0.53-0.73. The clear differences between Nymphaea candida versus Nuphar lutea and Nymphaea alba , may be due to adaptations of Nymphaea candida to an Euro-Siberic climate with short-lasting summer conditions.

Characterization of airborne float coal dust emitted during continuous mining, longwall mining and belt transport.

Science.gov (United States)

Shahan, M R; Seaman, C E; Beck, T W; Colinet, J F; Mischler, S E

2017-09-01

Float coal dust is produced by various mining methods, carried by ventilating air and deposited on the floor, roof and ribs of mine airways. If deposited, float dust is re-entrained during a methane explosion. Without sufficient inert rock dust quantities, this float coal dust can propagate an explosion throughout mining entries. Consequently, controlling float coal dust is of critical interest to mining operations. Rock dusting, which is the adding of inert material to airway surfaces, is the main control technique currently used by the coal mining industry to reduce the float coal dust explosion hazard. To assist the industry in reducing this hazard, the Pittsburgh Mining Research Division of the U.S. National Institute for Occupational Safety and Health initiated a project to investigate methods and technologies to reduce float coal dust in underground coal mines through prevention, capture and suppression prior to deposition. Field characterization studies were performed to determine quantitatively the sources, types and amounts of dust produced during various coal mining processes. The operations chosen for study were a continuous miner section, a longwall section and a coal-handling facility. For each of these operations, the primary dust sources were confirmed to be the continuous mining machine, longwall shearer and conveyor belt transfer points, respectively. Respirable and total airborne float dust samples were collected and analyzed for each operation, and the ratio of total airborne float coal dust to respirable dust was calculated. During the continuous mining process, the ratio of total airborne float coal dust to respirable dust ranged from 10.3 to 13.8. The ratios measured on the longwall face were between 18.5 and 21.5. The total airborne float coal dust to respirable dust ratio observed during belt transport ranged between 7.5 and 21.8.

Photon-gated spin transistor

OpenAIRE

Li, Fan; Song, Cheng; Cui, Bin; Peng, Jingjing; Gu, Youdi; Wang, Guangyue; Pan, Feng

2017-01-01

Spin-polarized field-effect transistor (spin-FET), where a dielectric layer is generally employed for the electrical gating as the traditional FET, stands out as a seminal spintronic device under the miniaturization trend of electronics. It would be fundamentally transformative if optical gating was used for spin-FET. We report a new type of spin-polarized field-effect transistor (spin-FET) with optical gating, which is fabricated by partial exposure of the (La,Sr)MnO3 channel to light-emitti...

Particle-in-Cell Simulation Study on the Floating Potential of Spacecraft in the Low Earth Orbit

International Nuclear Information System (INIS)

Tang Daotan; Yang Shengsheng; Zheng Kuohai; Qin Xiaogang; Li Detian; Liu Qing; Zhao Chengxuan; Du Shanshan

2015-01-01

In order to further understand the characteristics of the floating potential of low earth orbit spacecraft, the effects of the electron current collection area, background electron temperature, photocurrent emission, spacecraft wake, and the shape of spacecraft on spacecraft floating potential were studied here by particle-in-cell simulation in the low earth orbit. The simulation results show that the electron current collection area and background electron temperature impact on the floating potential by changing the electron current collection of spacecraft. By increasing the electron current collection area or background electron temperature, the spacecraft will float at a lower electric potential with respect to the surrounding plasma. However, the spacecraft wake affects the floating potential by increasing the ion current collected by spacecraft. The emission of the photocurrent from the spacecraft surface, which compensates for the electrons collected from background plasma, causes the floating potential to increase. The shape of the spacecraft is also an important factor influencing the floating potential. (paper)

On photonic controlled phase gates

International Nuclear Information System (INIS)

Kieling, K; Eisert, J; O'Brien, J L

2010-01-01

As primitives for entanglement generation, controlled phase gates have a central role in quantum computing. Especially in ideas realizing instances of quantum computation in linear optical gate arrays, a closer look can be rewarding. In such architectures, all effective nonlinearities are induced by measurements. Hence the probability of success is a crucial parameter of such quantum gates. In this paper, we discuss this question for controlled phase gates that implement an arbitrary phase with one and two control qubits. Within the class of post-selected gates in dual-rail encoding with vacuum ancillas, we identify the optimal success probabilities. We construct networks that allow for implementation using current experimental capabilities in detail. The methods employed here appear specifically useful with the advent of integrated linear optical circuits, providing stable interferometers on monolithic structures.

Floating point only SIMD instruction set architecture including compare, select, Boolean, and alignment operations

Science.gov (United States)

Gschwind, Michael K [Chappaqua, NY

2011-03-01

Mechanisms for implementing a floating point only single instruction multiple data instruction set architecture are provided. A processor is provided that comprises an issue unit, an execution unit coupled to the issue unit, and a vector register file coupled to the execution unit. The execution unit has logic that implements a floating point (FP) only single instruction multiple data (SIMD) instruction set architecture (ISA). The floating point vector registers of the vector register file store both scalar and floating point values as vectors having a plurality of vector elements. The processor may be part of a data processing system.

Design and preparation of controlled floating gastroretentive ...

African Journals Online (AJOL)

gastroretentive delivery systems for enhanced fexofenadine ... Abstract. Purpose: To design and prepare effervescent floating gastroretentive tablets for controlled fexofenadine ..... Complex of Carbopol with Polyvinylpyrrolidone as a. Matrix for ...

Sustainability and the future of managed floating in China

OpenAIRE

Švarc, Jiří

2009-01-01

The purpose of this thesis is to study the Balance of Payments and the Exchange Rate of the People's Republic of China, and it aims to assess whether the current performance of their Managed Floating Exchange Rate is sustainable in the future (given the equilibrium of China's Balance of Payments) and examine what effect would a Free Floating Renminbi Exchange Rate have on the Chinese economy. The work uses the method of compilation - gathering and organizing information on the development of ...

Preparation of NiFe binary alloy nanocrystals for nonvolatile memory applications

Institute of Scientific and Technical Information of China (English)

无

2010-01-01

In this work,an idea which applies binary alloy nanocrystal floating gate to nonvolatile memory application was introduced.The relationship between binary alloy’s work function and its composition was discussed theoretically.A nanocrystal floating gate structure with NiFe nanocrystals embedded in SiO2 dielectric layers was fabricated by magnetron sputtering.The micro-structure and composition deviation of the prepared NiFe nanocrystals were also investigated by TEM and EDS.

Reversible logic gates on Physarum Polycephalum

International Nuclear Information System (INIS)

Schumann, Andrew

2015-01-01

In this paper, we consider possibilities how to implement asynchronous sequential logic gates and quantum-style reversible logic gates on Physarum polycephalum motions. We show that in asynchronous sequential logic gates we can erase information because of uncertainty in the direction of plasmodium propagation. Therefore quantum-style reversible logic gates are more preferable for designing logic circuits on Physarum polycephalum

Nuclear floating power desalination complexes

International Nuclear Information System (INIS)

Panov, Y.K.; Polunichev, V.I.; Zverev, K.V.

1998-01-01

Russia is a single country in the world which possesses a powerful ice-breaker transport fleet that allows a solution of important social-economic tasks of the country's northern regions by maintaining a year-round navigation along the Arctic sea route. A total operating record of the marine nuclear reactors up until till now exceeds 150 reactor-years, with their main equipment operating life reacting 120 thousand hours. Design and constructional progresses have been made continuously during forty years of nuclear-powered ships construction in Russia. Well proven technology of all components experienced in the marine nuclear reactors give grounds to recommend marine NSSSs of KLT-40 type as energy sources for the heat and power co-generation plants and the sea water desalination complexes, particularly as a floating installation. Co-generation stations are considered for deployment in the extreme Northern Region of Russia. Nuclear floating desalination complexes can be used for drinkable water production in the coastal regions of Northern Africa, the Near East, India etc. (author)

Caspian Sea Energy: Oil, Politics and Development in the Caspian Sea Region (CD-ROM)

National Research Council Canada - National Science Library

Light, Chris

2004-01-01

...: 1 CD-ROM; 4 3/4 in.; 5.0 MB. ABSTRACT: The purpose of this paper is to present the major issues impacting Caspian hydrocarbon development Specifically, a number of topics including the regions geography, history, governments, politics...

Numerical modelling of floating debris in the world's oceans.

Science.gov (United States)

Lebreton, L C-M; Greer, S D; Borrero, J C

2012-03-01

A global ocean circulation model is coupled to a Lagrangian particle tracking model to simulate 30 years of input, transport and accumulation of floating debris in the world ocean. Using both terrestrial and maritime inputs, the modelling results clearly show the formation of five accumulation zones in the subtropical latitudes of the major ocean basins. The relative size and concentration of each clearly illustrate the dominance of the accumulation zones in the northern hemisphere, while smaller seas surrounded by densely populated areas are also shown to have a high concentration of floating debris. We also determine the relative contribution of different source regions to the total amount of material in a particular accumulation zone. This study provides a framework for describing the transport, distribution and accumulation of floating marine debris and can be continuously updated and adapted to assess scenarios reflecting changes in the production and disposal of plastic worldwide. Copyright © 2012 Elsevier Ltd. All rights reserved.

Stanford, Duke, Rice,... and Gates?

Science.gov (United States)

Carey, Kevin

2009-01-01

This article presents an open letter to Bill Gates. In his letter, the author suggests that Bill Gates should build a brand-new university, a great 21st-century institution of higher learning. This university will be unlike anything the world has ever seen. He asks Bill Gates not to stop helping existing colleges create the higher-education system…

Galvenais varonis Dž.K.Roulingas romānu sērijā "Harijs Poters"

OpenAIRE

Kalsone, Ineta

2012-01-01

Dotā bakalaura darba temats ir "Galvenais varonis Dž.K. Roulingas romānu sērijā "Harijs Poters". Pirmajā nodaļā es analizēju sērijas popularitāti, publicēšanas datus un apbalvojumus, ko saņēmusi Dž.K. Roulinga. Otrajā nodaļā tiek analizēti dažādi raksturojuma veidi. Sīkāk tiek pētīta galvenā varoņa un citu nozīmīgāko tēlu loma. Meklējuma literatūras elementi,kas dod pamatu galvenā varoņa izaugsmei, tika analizēti detalizēti. Trešajā nodaļā tiek analizēta galvenā varoņa izaugsme šajā romānu sē...

Fresh water generators onboard a floating platform

International Nuclear Information System (INIS)

Tewari, P.K.; Verma, R.K.; Misra, B.M.; Sadhulkan, H.K.

1997-01-01

A dependable supply of fresh water is essential for any ocean going vessel. The operating and maintenance personnel on offshore platforms and marine structures also require a constant and regular supply of fresh water to meet their essential daily needs. A seawater thermal desalination unit onboard delivers good quality fresh water from seawater. The desalination units developed by Bhabha Atomic Research Centre (BARC) suitable for ocean going vessels and offshore platforms have been discussed. Design considerations of such units with reference to floating platforms and corrosive environments have been presented. The feasibility of coupling a low temperature vacuum evaporation (LTVE) desalination plant suitable for an onboard floating platform to a PHWR nuclear power plant has also been discussed. (author). 1 ref., 3 figs, 2 tabs

Stress and deflection analyses of floating roofs based on a load-modifying method

International Nuclear Information System (INIS)

Sun Xiushan; Liu Yinghua; Wang Jianbin; Cen Zhangzhi

2008-01-01

This paper proposes a load-modifying method for the stress and deflection analyses of floating roofs used in cylindrical oil storage tanks. The formulations of loads and deformations are derived according to the equilibrium analysis of floating roofs. Based on these formulations, the load-modifying method is developed to conduct a geometrically nonlinear analysis of floating roofs with the finite element (FE) simulation. In the procedure with the load-modifying method, the analysis is carried out through a series of iterative computations until a convergence is achieved within the error tolerance. Numerical examples are given to demonstrate the validity and reliability of the proposed method, which provides an effective and practical numerical solution to the design and analysis of floating roofs

Fine mapping of Best`s macular dystrophy localises the gene in close proximity to, but distinct from, the D115480/ROM1

Energy Technology Data Exchange (ETDEWEB)

Graff, C.; Ahlbom, B.E.; Anneren, G. [University Hospital, Uppsala (Sweden)] [and others

1994-09-01

Best`s macular dystrophy (BMD) is an autosomal dominant disease characterized by accumulation of lipofuscin beneath the pigment epithelium of the macula, leading to early-onset impairment of central vision. The gene has previously been mapped to 11q13. Based on DNA from 191 people from a large 12-generation family, the gene now has been mapped to a 1.5 cM interval between the markers Fc{epsilon}RI and D11S480/ROM1. By disequilibrium analysis the gene was estimated to be 0.321 cM centromeric to the marker D11S480. Since this on average corresponds to 300 kb, the gene may be at a distance contained in YAC molecules. To physically characterize this region, YAC clones positive for markers flanking BMD have been identified. Sequence analysis of the candidate gene ROM1 did not reveal any mutation. However, one recombination between intragenic ROM1 polymorphisms and BMD was detected, which make it highly unlikely that mutations in ROM1 are causing BMD.

Implementing floating-point DSP

Czech Academy of Sciences Publication Activity Database

Kadlec, Jiří; Chappel, S.

2006-01-01

Roč. 2, č. 3 (2006), s. 12-14 R&D Projects: GA AV ČR 1ET400750406; GA MŠk 1M0567 EU Projects: European Commission(XE) 027611 - AETHER Program:FP6 Institutional research plan: CEZ:AV0Z10750506 Keywords : PicoBlaze * floating point * FPGA Subject RIV: JC - Computer Hardware ; Software http://www.xilinx.com/publications/ magazines /emb_03/xc_pdf/p12-14_3emb-point.pdf

Benchmarking gate-based quantum computers

Science.gov (United States)

Michielsen, Kristel; Nocon, Madita; Willsch, Dennis; Jin, Fengping; Lippert, Thomas; De Raedt, Hans

2017-11-01

With the advent of public access to small gate-based quantum processors, it becomes necessary to develop a benchmarking methodology such that independent researchers can validate the operation of these processors. We explore the usefulness of a number of simple quantum circuits as benchmarks for gate-based quantum computing devices and show that circuits performing identity operations are very simple, scalable and sensitive to gate errors and are therefore very well suited for this task. We illustrate the procedure by presenting benchmark results for the IBM Quantum Experience, a cloud-based platform for gate-based quantum computing.

Model predictive control for a dual active bridge inverter with a floating bridge

OpenAIRE

Chowdhury, Shajjad; Wheeler, Patrick W.; Gerada, C.; Patel, Chintan

2016-01-01

This paper presents a Model Predictive Control technique applied to a dual active bridge inverter where one of the bridges is floating. The proposed floating bridge topology eliminates the need for isolation transformer in a dual inverter system and therefore reduces the size, weight and losses in the system. To achieve multilevel output voltage waveforms the floating inverter DC link capacitor is charged to the half of the main DC link voltage. A finite-set Model Predictive Control technique...

An Integrated Structural Strength Analysis Method for Spar Type Floating Wind Turbine

Institute of Scientific and Technical Information of China (English)

胡志强; 刘毅; 王晋

2016-01-01

An integrated structural strength analysis method for a Spar type floating wind turbine is proposed in this paper, and technical issues related to turbine structure modeling and stress combination are also addressed. The NREL-5MW “Hywind” Spar type wind turbine is adopted as study object. Time-domain dynamic coupled simulations are performed by a fully-coupled aero-hydro-servo-elastic tool, FAST, on the purpose of obtaining the dynamic characteristics of the floating wind turbine, and determining parameters for design load cases of finite element calculation. Then design load cases are identified, and finite element analyses are performed for these design load cases. The structural stresses due to wave-induced loads and wind-induced loads are calculated, and then combined to assess the structural strength of the floating wind turbine. The feasibility of the proposed structural strength analysis method for floating wind turbines is then validated.

Ichtyofauna associated with drifting floating objects in the Balearic Islands (Western Mediterranean

Directory of Open Access Journals (Sweden)

Francisco Riera

1999-12-01

Full Text Available Species composition, size range and some behavioral notes about drifting flotsam associated fish of the Balearic Islands are presented, and more detailed observations on Seriola dumerili, Naucrates ductor, Coryphaena hippurus and Scomberesox saurus are also given. 25 fish species belonging to 18 families were identified, 12 of these species and the individuals of the family Mugilidae were recorded for the first time associated with floating objects in the western Mediterranean. Most of the specimens collected were juveniles, which suggests the importance of floating objects as a nursery, and thus in the recruitment and redistribution of fishes. Analisis of two drift floating material samples show that objects of anthropogenic origin were most abundant (83.5% and 63.5% and suggests that at present, human refuse may have taken over the role of the floating remains of marine plants for fishes in the western Mediterranean pelagic environment.

Application of a movable active vibration control system on a floating raft

Science.gov (United States)

Wang, Zhen; Mak, Cheuk Ming

2018-02-01

This paper presents a theoretical study of an inertial actuator connected to an accelerometer by a local feedback loop for active vibration control on a floating raft. On the criterion of the minimum power transmission from the vibratory machines to the flexible foundation in the floating raft, the best mounting positions for the inertial actuator on the intermediate mass of the floating raft are investigated. Simulation results indicate that the best mounting positions for the inertial actuator vary with frequency. To control time-varying excitations of vibratory machines on a floating raft effectively, an automatic control system based on real-time measurement of a cost function and automatically searching the best mounting position of the inertial actuator is proposed. To the best of our knowledge, it is the first time that an automatic control system is proposed to move an actuator automatically for controlling a time-varying excitation.

COPPER RESISTANT STRAIN CANDIDA TROPICALIS RomCu5 INTERACTION WITH SOLUBLE AND INSOLUBLE COPPER COMPOUNDS

Directory of Open Access Journals (Sweden)

Ie. P. Prekrasna

2015-10-01

Full Text Available The focus of the study was interaction of Candida tropicalis RomCu5 isolated from highland Ecuador ecosystem with soluble and insoluble copper compounds. Strain C. tropicalis RomCu5 was cultured in a liquid medium of Hiss in the presence of soluble (copper citrate and CuCl2 and insoluble (CuO and CuCO3 copper compounds. The biomass growth was determined by change in optical density of culture liquid, composition of the gas phase was measured on gas chromatograph, redox potential and pH of the culture fluid was defined potentiometrically. The concentration of soluble copper compounds was determined colorimetrically. Maximal permissible concentration of Cu2+ for C. tropicalis RomCu5 was 30 000 ppm of Cu2+ in form of copper citrate and 500 ppm of Cu2+ in form of CuCl2. C. tropicalis was metabolically active at super high concentrations of Cu2+, despite the inhibitory effect of Cu2+. C. tropicalis immobilized Cu2+ in the form of copper citrate and CuCl2 by it accumulation in the biomass. Due to medium acidification C. tropicalis dissolved CuO and CuCO3. High resistance of C. tropicalis to Cu2+ and ability to interact with soluble and insoluble copper compounds makes it biotechnologically perspective.

Design and in vitro evaluation of multiparticulate floating drug delivery system of zolpidem tartarate.

Science.gov (United States)

Amrutkar, P P; Chaudhari, P D; Patil, S B

2012-01-01

Zolpidem tartarate is a non-benzodiazepine, sedative-hypnotic, which finds its major use in various types of insomnia. The present work relates to development of multiparticulate floating drug delivery system based on gas generation technique to prolong the gastric residence time and to increase the overall bioavailability. Modified release dosage form of zolpidem tartarate adapted to release over a predetermined time period, according to biphasic profile of dissolution, where the first phase is immediate release phase for inducing the sleep and the second phase is modified release phase for maintaining the sleep up to 10 h. The system consists of zolpidem tartarate layered pellets coated with effervescent layer and polymeric membrane. The floating ability and in vitro drug release of the system were dependent on amount of the effervescent agent (sodium bicarbonate) layered onto the drug layered pellets, and coating level of the polymeric membrane (Eudragit(®) NE 30D). The system could float completely within 5 min and maintain the floating over a period of 10 h. The multiparticulate floating delivery system of zolpidem tartarate with rapid floating and modified drug release was obtained. Copyright © 2011 Elsevier B.V. All rights reserved.

RESEARCH OF USING OPEN DOUBLE T BEAMS FOR SPANS IN FLOATING BRIDGES

Directory of Open Access Journals (Sweden)

YU. M. Gorbatiuk

2014-03-01

Full Text Available Purpose. The publication presents the results of calculations of spans for floating bridges with open double T beams. The purpose of research is to analyze the suitability of spans from open double T beams for floating bridges with minimum weight under loads, which is provided by standards for modern floating bridges designing. Methodology. Comparative method, analytical calculation methods (influence lines methodology, strength calculations, endurance, maximum shear stress are used in this paper. Findings. Current loads for bridges calculations are 75% more than those, for which the spans of floating bridge from NZhM-56 property are designed. The use of open double T beams that is formed with double T beam no. 70 (the height of the open one is 104 cm reduces the cross sectional area in a weakened spot, but virtually it does not influence the strength and durability of the material. The use of open double T beams for spans of floating bridges saves up to 22 % of metal that means one in five spans will made of saved metal. Savings on each spans, such as CRP, will be 33.6 - 263 thous. grn. (considering the price of 1 ton of final product 29 thous. grn.. Originality. Research allows making next step in material saving and use of open double T beams for spans in the whole. Practical value. The obtained results give us possibility to make a number of conclusions that allow us to become more familiar and more practical with the use of open double T beams for spans of floating bridges.

Plant traits and environment: floating leaf blade production and turnover of waterlilies

Directory of Open Access Journals (Sweden)

Peter F. Klok

2017-04-01

Full Text Available Floating leaf blades of waterlilies fulfill several functions in wetland ecosystems by production, decomposition and turnover as well as exchange processes. Production and turnover rates of floating leaf blades of three waterlily species, Nuphar lutea (L. Sm., Nymphaea alba L. and Nymphaea candida Presl, were studied in three freshwater bodies, differing in trophic status, pH and alkalinity. Length and percentages of leaf loss of marked leaf blades were measured weekly during the growing season. Area and biomass were calculated based on leaf length and were used to calculate the turnover rate of floating leaf blades. Seasonal changes in floating leaf production showed that values decreased in the order: Nymphaea alba, Nuphar lutea, Nymphaea candida. The highest production was reached for Nuphar lutea and Nymphaea alba in alkaline, eutrophic water bodies. The production per leaf was relatively high for both species in the acid water body. Nymphaea candida showed a very short vegetation period and low turnover rates. The ratio Total potential leaf biomass/Maximum potential leaf biomass (P/Bmax of the three species ranged from 1.35–2.25. The ratio Vegetation period (Period with floating leaves/Mean leaf life span ranged from 2.94–4.63, the ratio Growth period (Period with appearance of new floating leaves/Vegetation period from 0.53–0.73. The clear differences between Nymphaea candida versus Nuphar lutea and Nymphaea alba, may be due to adaptations of Nymphaea candida to an Euro-Siberic climate with short-lasting summer conditions.

Year 5 Pupils Reading an "Interactive Storybook" on CD-ROM: Losing the Plot?

Science.gov (United States)

Trushell, John; Burrell, Clare; Maitland, Amanda

2001-01-01

This study examined whether small groups of grade 5 students in a London primary school, without teacher supervision, progressed linearly through an interactive storybook on CD-ROM, and whether such diversions as cued animations affected pupil comprehension. Results showed students' recall of the storyline was poor. (Author/LRW)

Setting Up CD-ROM Work Areas. Part I: Ergonomic Considerations, User Furniture, Location.

Science.gov (United States)

Vasi, John; LaGuardia, Cheryl

1992-01-01

The first of a two-part series on design of CD-ROM work areas in libraries discusses (1) space and location considerations; (2) ergonomics, including work surface, chairs, lighting, printers, other accessories, and security; and (3) other considerations, including staff assistance, reference tools, literature racks, and promotional materials. (MES)

Underwater and Floating-Leaved Plants of the United States and Canada.

Science.gov (United States)

Hotchkiss, Neil

This is the third in a series of guides to the field identification of North American marsh and water plants. Described are plants which have foliage habitually under water or floating, or which have underwater or floating forms, and which have characteristics by which they can be distinguished with the naked eye. Where genera or species cannot be…

Gate Engineering in SOI LDMOS for Device Reliability

Directory of Open Access Journals (Sweden)

Aanand

2016-01-01

Full Text Available A linearly graded doping drift region with step gate structure, used for improvement of reduced surface field (RESURF SOI LDMOS transistor performance has been simulated with 0.35µm technology in this paper. The proposed device has one poly gate and double metal gate arranged in a stepped manner, from channel to drift region. The first gate uses n+ poly (near source where as other two gates of aluminium. The first gate with thin gate oxide has good control over the channel charge. The third gate with thick gate oxide at drift region reduce gate to drain capacitance. The arrangement of second and third gates in a stepped manner in drift region spreads the electric field uniformly. Using two dimensional device simulations, the proposed SOI LDMOS is compared with conventional structure and the extended metal structure. We demonstrate that the proposed device exhibits significant enhancement in linearity, breakdown voltage, on-resistance and HCI. Double metal gate reduces the impact ionization area which helps to improve the Hot Carrier Injection effect..

Reis kosmosesse : [Floating-kambrist] / Marika Makarova

Index Scriptorium Estoniae

Makarova, Marika

2011-01-01

Ameerika psühholoogi John C. Lilly poolt kasutusele võetud Floating-kambrist ehk hõljumisvannist, mis aeglustab ajulaineid ning seeläbi aitab vähendada lihaspinget, stressi, ärevust, peavalusid, vererõhku ning parandada und, selgroo- ja kaelavigastusi, suurendada loovust ja heaolu jne

Effect of top gate potential on bias-stress for dual gate amorphous indium-gallium-zinc-oxide thin film transistor

Energy Technology Data Exchange (ETDEWEB)

Chun, Minkyu; Um, Jae Gwang; Park, Min Sang; Chowdhury, Md Delwar Hossain; Jang, Jin, E-mail: jjang@khu.ac.kr [Advanced Display Research Center and Department of Information Display, Kyung Hee University, Seoul 02447 (Korea, Republic of)

2016-07-15

We report the abnormal behavior of the threshold voltage (V{sub TH}) shift under positive bias Temperature stress (PBTS) and negative bias temperature stress (NBTS) at top/bottom gate in dual gate amorphous indium-gallium-zinc-oxide (a-IGZO) thin-film transistors (TFTs). It is found that the PBTS at top gate shows negative transfer shift and NBTS shows positive transfer shift for both top and bottom gate sweep. The shift of bottom/top gate sweep is dominated by top gate bias (V{sub TG}), while bottom gate bias (V{sub BG}) is less effect than V{sub TG}. The X-ray photoelectron spectroscopy (XPS) depth profile provides the evidence of In metal diffusion to the top SiO{sub 2}/a-IGZO and also the existence of large amount of In{sup +} under positive top gate bias around top interfaces, thus negative transfer shift is observed. On the other hand, the formation of OH{sup −} at top interfaces under the stress of negative top gate bias shows negative transfer shift. The domination of V{sub TG} both on bottom/top gate sweep after PBTS/NBTS is obviously occurred due to thin active layer.

The floating knee: epidemiology, prognostic indicators & outcome following surgical management.

Science.gov (United States)

Rethnam, Ulfin; Yesupalan, Rajam S; Nair, Rajagopalan

2007-11-26

Floating Knee injuries are complex injuries. The type of fractures, soft tissue and associated injuries make this a challenging problem to manage. We present the outcome of these injuries after surgical management. 29 patients with floating knee injuries were managed over a 3 year period. This was a prospective study were both fractures of the floating knee injury were surgically fixed using different modalities. The associated injuries were managed appropriately. Assessment of the end result was done by the Karlstrom criteria after bony union. The mechanism of injury was road traffic accident in 27/29 patients. There were 38 associated injuries. 20/29 patients had intramedullary nailing for both fractures. The complications were knee stiffness, foot drop, delayed union of tibia and superficial infection. The bony union time ranged from 15 - 22.5 weeks for femur fractures and 17 - 28 weeks for the tibia. According to the Karlstrom criteria the end results were Excellent - 15, Good - 11, Acceptable - 1 and Poor - 3. The associated injuries and the type of fracture (open, intra-articular, comminution) are prognostic indicators in the Floating knee. Appropriate management of the associated injuries, intramedullary nailing of both the fractures and post operative rehabilitation are necessary for good final outcome.

Recovery of uranium from seawater using wave power and floating offshore units

International Nuclear Information System (INIS)

Bjoerk, B.; Vallander, P.

1981-03-01

This report is the final contribution to a study of the technical and economic feasibility of floating units for the recovery of uranium from seawater. The seawater is supplied by wave energy and received by a sloping plane. An optimization was carried out which involved study of the number of storeys of adsorbent beds in a floating unit, the number and tonnage of service vessels and the number of moorings. Different absorbent bed areas, thicknesses of layers of adsorbent material, length of floating units and length of extraction cycles were considered. The annual uranium uptake was calculated for an offshore location 20 nautical miles to the south-east of South Africa. The costs of the total plant for each combination of optimization parameters were calculated and are presented. The cost of the recovered uranium for each combination of optimization parameters is shown. The most feasible offshore plant will recover uranium at a cost of about 1 900 SEK/kg. It will comprise 22 floating units, each with an adsorbent bed area of 300 m 2 per metre of the unit and an adsorbent thickness of 0.10 metres. A conceptual layout of the selected floating unit is shown in drawings. (author)

Optimal trajectory planning of free-floating space manipulator using differential evolution algorithm

Science.gov (United States)

Wang, Mingming; Luo, Jianjun; Fang, Jing; Yuan, Jianping

2018-03-01

The existence of the path dependent dynamic singularities limits the volume of available workspace of free-floating space robot and induces enormous joint velocities when such singularities are met. In order to overcome this demerit, this paper presents an optimal joint trajectory planning method using forward kinematics equations of free-floating space robot, while joint motion laws are delineated with application of the concept of reaction null-space. Bézier curve, in conjunction with the null-space column vectors, are applied to describe the joint trajectories. Considering the forward kinematics equations of the free-floating space robot, the trajectory planning issue is consequently transferred to an optimization issue while the control points to construct the Bézier curve are the design variables. A constrained differential evolution (DE) scheme with premature handling strategy is implemented to find the optimal solution of the design variables while specific objectives and imposed constraints are satisfied. Differ from traditional methods, we synthesize null-space and specialized curve to provide a novel viewpoint for trajectory planning of free-floating space robot. Simulation results are presented for trajectory planning of 7 degree-of-freedom (DOF) kinematically redundant manipulator mounted on a free-floating spacecraft and demonstrate the feasibility and effectiveness of the proposed method.

CMOS gate array characterization procedures

Science.gov (United States)

Spratt, James P.

1993-09-01

Present procedures are inadequate for characterizing the radiation hardness of gate array product lines prior to personalization because the selection of circuits to be used, from among all those available in the manufacturer's circuit library, is usually uncontrolled. (Some circuits are fundamentally more radiation resistant than others.) In such cases, differences in hardness can result between different designs of the same logic function. Hardness also varies because many gate arrays feature large custom-designed megacells (e.g., microprocessors and random access memories-MicroP's and RAM's). As a result, different product lines cannot be compared equally. A characterization strategy is needed, along with standardized test vehicle(s), methodology, and conditions, so that users can make informed judgments on which gate arrays are best suited for their needs. The program described developed preferred procedures for the radiation characterization of gate arrays, including a gate array evaluation test vehicle, featuring a canary circuit, designed to define the speed versus hardness envelope of the gate array. A multiplier was chosen for this role, and a baseline multiplier architecture is suggested that could be incorporated into an existing standard evaluation circuit chip.

GATE: Improving the computational efficiency

International Nuclear Information System (INIS)

Staelens, S.; De Beenhouwer, J.; Kruecker, D.; Maigne, L.; Rannou, F.; Ferrer, L.; D'Asseler, Y.; Buvat, I.; Lemahieu, I.

2006-01-01

GATE is a software dedicated to Monte Carlo simulations in Single Photon Emission Computed Tomography (SPECT) and Positron Emission Tomography (PET). An important disadvantage of those simulations is the fundamental burden of computation time. This manuscript describes three different techniques in order to improve the efficiency of those simulations. Firstly, the implementation of variance reduction techniques (VRTs), more specifically the incorporation of geometrical importance sampling, is discussed. After this, the newly designed cluster version of the GATE software is described. The experiments have shown that GATE simulations scale very well on a cluster of homogeneous computers. Finally, an elaboration on the deployment of GATE on the Enabling Grids for E-Science in Europe (EGEE) grid will conclude the description of efficiency enhancement efforts. The three aforementioned methods improve the efficiency of GATE to a large extent and make realistic patient-specific overnight Monte Carlo simulations achievable

Preparation and investigation of novel gastro-floating tablets with 3D extrusion-based printing.

Science.gov (United States)

Li, Qijun; Guan, Xiaoying; Cui, Mengsuo; Zhu, Zhihong; Chen, Kai; Wen, Haoyang; Jia, Danyang; Hou, Jian; Xu, Wenting; Yang, Xinggang; Pan, Weisan

2018-01-15

Three dimensional (3D) extrusion-based printing is a paste-based rapid prototyping process, which is capable of building complex 3D structures. The aim of this study was to explore the feasibility of 3D extrusion-based printing as a pharmaceutical manufacture technique for the fabrication of gastro-floating tablets. Novel low-density lattice internal structure gastro-floating tablets of dipyridamole were developed to prolong the gastric residence time in order to improve drug release rate and consequently, improve bioavailability and therapeutic efficacy. Excipients commonly employed in the pharmaceutical study could be efficiently applied in the room temperature 3D extrusion-based printing process. The tablets were designed with three kinds of infill percentage and prepared by hydroxypropyl methylcellulose (HPMC K4M) and hydroxypropyl methylcellulose (HPMC E15) as hydrophilic matrices and microcrystalline cellulose (MCC PH101) as extrusion molding agent. In vitro evaluation of the 3D printed gastro-floating tablets was performed by determining mechanical properties, content uniformity, and weight variation. Furthermore, re-floating ability, floating duration time, and drug release behavior were also evaluated. Dissolution profiles revealed the relationship between infill percentage and drug release behavior. The results of this study revealed the potential of 3D extrusion-based printing to fabricate gastro-floating tablets with more than 8h floating process with traditional pharmaceutical excipients and lattice internal structure design. Copyright © 2017. Published by Elsevier B.V.

Dual-gated cardiac PET-clinical feasibility study

Energy Technology Data Exchange (ETDEWEB)

Teraes, Mika; Kokki, Tommi; Noponen, Tommi; Hoppela, Erika; Sipilae, Hannu T.; Knuuti, Juhani [Turku PET Centre, PO BOX 52, Turku (Finland); Durand-Schaefer, Nicolas [General Electric Medical Systems, Buc (France); Pietilae, Mikko [Turku University Hospital, Department of Internal Medicine, Turku (Finland); Kiss, Jan [Turku University Hospital, Department of Surgery, Turku (Finland)

2010-03-15

Both respiratory and cardiac motions reduce image quality in myocardial imaging. For accurate imaging of small structures such as vulnerable coronary plaques, simultaneous cardiac and respiratory gating is warranted. This study tests the feasibility of a recently developed robust method for cardiac-respiratory gating. List-mode data with triggers from respiratory and cardiac cycles are rearranged into dual-gated segments and reconstructed with standard algorithms of a commercial PET/CT scanner. Cardiac gates were defined as three fixed phases and one variable diastolic phase. Chest motion was measured with a respiratory gating device and post-processed to determine gates. Preservation of quantification in dual-gated images was tested with an IEC whole-body phantom. Minipig and human studies were performed to evaluate the feasibility of the method. In minipig studies, a coronary catheter with radioactive tip was guided in coronary artery for in vivo and ex vivo acquisitions. Dual gating in humans with suspected cardiac disorders was performed using 18-F-FDG as a tracer. The method was found feasible for in vivo imaging and the radioactive catheter tip was better resolved in gated images. In human studies, the dual gating was found feasible and easy for clinical routine. Maximal movement of myocardial surface in cranio-caudal direction was over 20 mm. The shape of myocardium was clearly different between the gates and papillary muscles become more visible in diastolic images. The first clinical experiences using robust cardiac-respiratory dual gating are encouraging. Further testing in larger clinical populations using tracers designed especially for plaque imaging is warranted. (orig.)

Dual-gated cardiac PET-clinical feasibility study

International Nuclear Information System (INIS)

Teraes, Mika; Kokki, Tommi; Noponen, Tommi; Hoppela, Erika; Sipilae, Hannu T.; Knuuti, Juhani; Durand-Schaefer, Nicolas; Pietilae, Mikko; Kiss, Jan

2010-01-01

Both respiratory and cardiac motions reduce image quality in myocardial imaging. For accurate imaging of small structures such as vulnerable coronary plaques, simultaneous cardiac and respiratory gating is warranted. This study tests the feasibility of a recently developed robust method for cardiac-respiratory gating. List-mode data with triggers from respiratory and cardiac cycles are rearranged into dual-gated segments and reconstructed with standard algorithms of a commercial PET/CT scanner. Cardiac gates were defined as three fixed phases and one variable diastolic phase. Chest motion was measured with a respiratory gating device and post-processed to determine gates. Preservation of quantification in dual-gated images was tested with an IEC whole-body phantom. Minipig and human studies were performed to evaluate the feasibility of the method. In minipig studies, a coronary catheter with radioactive tip was guided in coronary artery for in vivo and ex vivo acquisitions. Dual gating in humans with suspected cardiac disorders was performed using 18-F-FDG as a tracer. The method was found feasible for in vivo imaging and the radioactive catheter tip was better resolved in gated images. In human studies, the dual gating was found feasible and easy for clinical routine. Maximal movement of myocardial surface in cranio-caudal direction was over 20 mm. The shape of myocardium was clearly different between the gates and papillary muscles become more visible in diastolic images. The first clinical experiences using robust cardiac-respiratory dual gating are encouraging. Further testing in larger clinical populations using tracers designed especially for plaque imaging is warranted. (orig.)

Floating nuclear energy plants for seawater desalination. Proceedings of a technical committee meeting

International Nuclear Information System (INIS)

1997-05-01

Floating nuclear desalination facilities are one of the alternatives being considered. They may offer a particularly suitable choice for remote locations and small island or coastal communities where the necessary manpower and infrastructure to support desalination plants are not available. In the interest of focusing specific attention on the technology of floating nuclear desalination, the IAEA sponsored a Technical Committee Meeting on Floating Nuclear Plants for Seawater Desalination from 29 to 31 May 1995 in Obninsk, Russian Federation. This publication documents the papers and presentations given by experts from several countries at that meeting. It is hoped that the information contained in this report will be a valuable resource for those interested in nuclear desalination, and that it will stimulate further interest in the potential for floating nuclear desalination facilities. Refs, figs, tabs

Demonstration of a Quantum Nondemolition Sum Gate

DEFF Research Database (Denmark)

Yoshikawa, J.; Miwa, Y.; Huck, Alexander

2008-01-01

The sum gate is the canonical two-mode gate for universal quantum computation based on continuous quantum variables. It represents the natural analogue to a qubit C-NOT gate. In addition, the continuous-variable gate describes a quantum nondemolition (QND) interaction between the quadrature...

Wake losses optimization of offshore wind farms with moveable floating wind turbines

NARCIS (Netherlands)

S.F. Rodrigues; R. Teixeira Pinto (Rodrigo); M. Soleimanzadeh (Maryam); P.A.N. Bosman (Peter); P. Bauer (Pavol)

2015-01-01

htmlabstractIn the future, floating wind turbines could be used to harvest energy in deep offshore areas where higher wind mean speeds are observed. Currently, several floating turbine concepts are being designed and tested in small scale projects; in particular, one concept allows the turbine to

Active pixel sensor pixel having a photodetector whose output is coupled to an output transistor gate

Science.gov (United States)

Fossum, Eric R. (Inventor); Nakamura, Junichi (Inventor); Kemeny, Sabrina E. (Inventor)

2005-01-01

An imaging device formed as a monolithic complementary metal oxide semiconductor integrated circuit in an industry standard complementary metal oxide semiconductor process, the integrated circuit including a focal plane array of pixel cells, each one of the cells including a photogate overlying the substrate for accumulating photo-generated charge in an underlying portion of the substrate and a charge coupled device section formed on the substrate adjacent the photogate having a sensing node and at least one charge coupled device stage for transferring charge from the underlying portion of the substrate to the sensing node. There is also a readout circuit, part of which can be disposed at the bottom of each column of cells and be common to all the cells in the column. A Simple Floating Gate (SFG) pixel structure could also be employed in the imager to provide a non-destructive readout and smaller pixel sizes.

CFD simulation of gas-liquid floating particles mixing in an agitated vessel

Directory of Open Access Journals (Sweden)

Li Liangchao

2017-01-01

Full Text Available Gas dispersion and floating particles suspension in an agitated vessel were studied numerically by using computational fluid dynamics (CFD. The Eulerian multi-fluid model along with standard k-ε turbulence model was used in the simulation. A multiple reference frame (MRF approach was used to solve the impeller rotation. The velocity field, gas and floating particles holdup distributions in the vessel were first obtained, and then, the effects of operating conditions on gas dispersion and solid suspension were investigated. The simulation results show that velocity field of solid phase and gas phase are quite different in the agitated vessel. Floating particles are easy to accumulate in the center of the surface region and the increasing of superficial gas velocity is in favor of floating particles off-surface suspension. With increasing solids loading, the gas dispersion becomes worse, while relative solid holdup distribution changes little. The limitations of the present modeling are discussed and further research in the future is proposed.

Recovery of uranium from seawater using wave power and floating offshore units

International Nuclear Information System (INIS)

Bjoerk, B.; Vallander, P.

1981-06-01

This report is a final contribution to a study of the technical and economic feasibility of floating units for the recovery of uranium from seawater. The seawater is supplied by wave energy and received by a sloping plane. An optimization was carried out which involved study of the number of storeys of adsorbent beds in a floating unit, the number and tonnage of service vessels and the number of moorings. Different adsorbent bed areas, thickness of layers of adsorbent material, length of floating units and length of extraction cycles were considered. The costs of a plant for each combination of optimization parameters were calculated and are presented. The most feasible offshore plant will recover uranium at a cost of about 1900 SEK/kg. It will comprise 22 floating units, each with an adsorbent bed area of 300 m 2 per metre of the unit and an adsorbent thickness of 0.10 metres. (Authors)

Towards Interactive Steering of a Very Large Floating Structure Code by Using HPC Parallelisation Strategies

KAUST Repository

Frisch, Jerome

2012-09-01

Very large floating structures (VLFSs) have been used for broad applications such as floating storage facilities, floating piers, floating bridges, floating airports, entertainment facilities, even habitation, and other purposes. Owing to its small bending rigidity, VLFS deforms elastically when subjected to wave action. This elastic deformation due to wave is called hydro elastic response and it can be obtained by solving the interaction between the surface wave and the floating structure in the frequency domain. In solving the fluid-structure interaction, the floating structure can be modelled by applying the finite element method, whereas the fluid part may be analyzed by using the Green\\'s function method. When using the Green\\'s function which satisfies the boundary condition on the free-surface, the sea bottom and that at infinite distance from the floating structure, the unknown parameters to be determined for the fluid part can be minimized to be only those associated with the wetted surface of the floating structure. However, in the evaluation of the Green\\'s function, extensive computation time O(N2) is needed (N is the number of unknowns). Therefore, acceleration techniques are necessary to tackle the computational complexity. Nowadays, standard multi-core office PCs are already quite powerful if all the cores can be used efficiently. This paper will show different parallelisation strategies for speeding up the Green\\'s function computation. A shared memory based implementation as well as a distributed memory concept will be analysed regarding speed-up and efficiency. For large computations, batch jobs can be used to compute detailed results in high resolution on a large computational cluster or supercomputer. Different speed-up computations on clusters will be included for showing strong speed-up results. © 2012 IEEE.

Helping Family Physicians Improve Their Cardiac Auscultation Skills with an Interactive CD-ROM.

Science.gov (United States)

Roy, Douglas; Sargeant, Joan; Gray, Jean; Hoyt, Brian; Allen, Michael; Fleming, Michael

2002-01-01

Physicians (n=42) studied cardiac auscultation using a 15-hour CD-ROM program. Nine months later, 21 who completed a posttest showed significant improvement in identifying heart sounds. CDs were valued for opportunities to review material at an individual pace. Lack of computer skills hindered use. (Contains 26 references.) (SK)

Whole Language, Computers and CD-ROM Technology: A Kindergarten Unit on "Benjamin Bunny."

Science.gov (United States)

Balajthy, Ernest

A kindergarten teacher, two preservice teachers, and a college consultant on educational computer technology designed and developed a 10-day whole-language integrated unit on the theme of Beatrix Potter's "Benjamin Bunny." The project was designed as a demonstration of the potential of integrating the CD-ROM-based version of…

How To Use the SilverPlatter Software To Search the ERIC CD ROM.

Science.gov (United States)

Merrill, Paul F.

This manual provides detailed instructions for using SilverPlatter software to search the ERIC CD ROM (Compact Disk Read Only Memory), a large bibliographic database relating to education which contains reference information on numerous journal articles from over 750 journals cited in the "Current Index to Journals in Education" (CIJE),…

IEEE Standard for Floating Point Numbers

Indian Academy of Sciences (India)

IAS Admin

Floating point numbers are an important data type in compu- tation which is used ... quite large! Integers are ... exp, the value of the exponent will be taken as (exp –127). The ..... bit which is truncated is 1, add 1 to the least significant bit, else.

Voltage-Controlled Floating Resistor Using DDCC

Directory of Open Access Journals (Sweden)

M. Kumngern

2011-04-01

Full Text Available This paper presents a new simple configuration to realize the voltage-controlled floating resistor, which is suitable for integrated circuit implementation. The proposed resistor is composed of three main components: MOS transistor operating in the non-saturation region, DDCC, and MOS voltage divider. The MOS transistor operating in the non-saturation region is used to configure a floating linear resistor. The DDCC and the MOS transistor voltage divider are used for canceling the nonlinear component term of MOS transistor in the non-saturation region to obtain a linear current/voltage relationship. The DDCC is employed to provide a simple summer of the circuit. This circuit offers an ease for realizing the voltage divider circuit and the temperature effect that includes in term of threshold voltage can be compensated. The proposed configuration employs only 16 MOS transistors. The performances of the proposed circuit are simulated with PSPICE to confirm the presented theory.

Floating / Travelling Gardens of (Postcolonial Time

Directory of Open Access Journals (Sweden)

Carmen Concilio

2017-11-01

Full Text Available This essay on travelling gardens of (postcolonial time opens with two iconic images of floating gardens in contemporary postcolonial literature: Will Phantom’s bio-garbage rafter, which saves him in the midst of a cyclone in Carpentaria (2008, by the Aboriginal author Alexis Wright, and Pi’s carnivore island-organism in Life of Pi (2001, which cannot save him from his shipwreck, by Canadian writer Yan Martel. These floating, hybrid gardens of the Anthropocene precede the real travelling gardens of both Michael Ondaatje’s The Cat’s Table (2011 and Amitav Ghosh’s Ibis Trilogy (2008-2015, two authors who both indirectly and directly tell the story of botanical gardens in Asia, and of plant and seed smuggling and transplantation (“displacement” also hinting at their historical and economic colonial implications. For, after all, botanical gardens imply a very specific version of care, Cura (Robert Pogue Harrison 2009, while embodying a precise, imperial scientific and economic project (Brockway 2002; Johnson 2011.

Multi-gated field emitters for a micro-column

International Nuclear Information System (INIS)

Mimura, Hidenori; Kioke, Akifumi; Aoki, Toru; Neo, Yoichiro; Yoshida, Tomoya; Nagao, Masayoshi

2011-01-01

We have developed a multi-gated field emitter (FE) such as a quadruple-gated FE with a three-stacked electrode lens and a quintuple-gated FE with a four-stacked electrode lens. Both the FEs can focus the electron beam. However, the quintuple-gated FE has a stronger electron convergence than the quadruple-gated FE, and a beam crossover is clearly observed for the quintuple-gated FE.

On the design of a radix-10 online floating-point multiplier

Science.gov (United States)

McIlhenny, Robert D.; Ercegovac, Milos D.

2009-08-01

This paper describes an approach to design and implement a radix-10 online floating-point multiplier. An online approach is considered because it offers computational flexibility not available with conventional arithmetic. The design was coded in VHDL and compiled, synthesized, and mapped onto a Virtex 5 FPGA to measure cost in terms of LUTs (look-up-tables) as well as the cycle time and total latency. The routing delay which was not optimized is the major component in the cycle time. For a rough estimate of the cost/latency characteristics, our design was compared to a standard radix-2 floating-point multiplier of equivalent precision. The results demonstrate that even an unoptimized radix-10 online design is an attractive implementation alternative for FPGA floating-point multiplication.

Multiplexed charge-locking device for large arrays of quantum devices

Energy Technology Data Exchange (ETDEWEB)

Puddy, R. K., E-mail: rkp27@cam.ac.uk; Smith, L. W; Chong, C. H.; Farrer, I.; Griffiths, J. P.; Ritchie, D. A.; Smith, C. G. [Cavendish Laboratory, University of Cambridge, Cambridge CB3 0HE (United Kingdom); Al-Taie, H.; Kelly, M. J. [Cavendish Laboratory, University of Cambridge, Cambridge CB3 0HE (United Kingdom); Centre for Advanced Photonics and Electronics, Electrical Engineering Division, Department of Engineering, 9 J. J. Thomson Avenue, University of Cambridge, Cambridge CB3 0FA (United Kingdom); Pepper, M. [Department of Electronic and Electrical Engineering, University College London, WC1E 7JE (United Kingdom)

2015-10-05

We present a method of forming and controlling large arrays of gate-defined quantum devices. The method uses an on-chip, multiplexed charge-locking system and helps to overcome the restraints imposed by the number of wires available in cryostat measurement systems. The device architecture that we describe here utilises a multiplexer-type scheme to lock charge onto gate electrodes. The design allows access to and control of gates whose total number exceeds that of the available electrical contacts and enables the formation, modulation and measurement of large arrays of quantum devices. We fabricate such devices on n-type GaAs/AlGaAs substrates and investigate the stability of the charge locked on to the gates. Proof-of-concept is shown by measurement of the Coulomb blockade peaks of a single quantum dot formed by a floating gate in the device. The floating gate is seen to drift by approximately one Coulomb oscillation per hour.

An evaluation of gating window size, delivery method, and composite field dosimetry of respiratory-gated IMRT

International Nuclear Information System (INIS)

Hugo, Geoffrey D.; Agazaryan, Nzhde; Solberg, Timothy D.

2002-01-01

A respiratory gating system has been developed based on a commercial patient positioning system. The purpose of this study is to investigate the ability of the gating system to reproduce normal, nongated IMRT operation and to quantify the errors produced by delivering a nongated IMRT treatment onto a moving target. A moving phantom capable of simultaneous two-dimensional motion was built, and an analytical liver motion function was used to drive the phantom. Studies were performed to assess the effect of gating window size and choice of delivery method (segmented and dynamic multileaf collimation). Additionally, two multiple field IMRT cases were delivered to quantify the error in gated and nongated IMRT with motion. Dosimetric error between nonmoving and moving deliveries is related to gating window size. By reducing the window size, the error can be reduced. Delivery error can be reduced for both dynamic and segmented delivery with gating. For the implementation of dynamic IMRT delivery in this study, dynamic delivery was found to generate larger delivery errors than segmented delivery in most cases studied. For multiple field IMRT delivery, the largest errors were generated in regions where high field modulation was present parallel to the axis of motion. Gating was found to reduce these large errors to clinically acceptable levels

Unsteady aerodynamic analysis for offshore floating wind turbines under different wind conditions.

Science.gov (United States)

Xu, B F; Wang, T G; Yuan, Y; Cao, J F

2015-02-28

A free-vortex wake (FVW) model is developed in this paper to analyse the unsteady aerodynamic performance of offshore floating wind turbines. A time-marching algorithm of third-order accuracy is applied in the FVW model. Owing to the complex floating platform motions, the blade inflow conditions and the positions of initial points of vortex filaments, which are different from the fixed wind turbine, are modified in the implemented model. A three-dimensional rotational effect model and a dynamic stall model are coupled into the FVW model to improve the aerodynamic performance prediction in the unsteady conditions. The effects of floating platform motions in the simulation model are validated by comparison between calculation and experiment for a small-scale rigid test wind turbine coupled with a floating tension leg platform (TLP). The dynamic inflow effect carried by the FVW method itself is confirmed and the results agree well with the experimental data of a pitching transient on another test turbine. Also, the flapping moment at the blade root in yaw on the same test turbine is calculated and compares well with the experimental data. Then, the aerodynamic performance is simulated in a yawed condition of steady wind and in an unyawed condition of turbulent wind, respectively, for a large-scale wind turbine coupled with the floating TLP motions, demonstrating obvious differences in rotor performance and blade loading from the fixed wind turbine. The non-dimensional magnitudes of loading changes due to the floating platform motions decrease from the blade root to the blade tip. © 2015 The Author(s) Published by the Royal Society. All rights reserved.

Dāvida Lodža „Mazā pasaule” un „Paradīzes jaunumi” kā piedzīvojumu romāni

OpenAIRE

Kaušakīte, Inessa

2007-01-01

Maģistra darbā „Deivida Lodža „Mazā pasaule” un „Paradīzes Jaunumi” kā piedzīvojumu romāni” mērķis ir pievērst uzmanību piedzīvojuma žanra dažādām īpatnībām mūsdienu angļu romānista darbos. Darbs arī atklāj postmodernā piedzīvojumu romāna varoņa rakstura īpatnības. Pirmā nodaļa izceļ klasiskā 16. gadsimta spāņu literatūras piedzīvojumu romāna svarīgākās īpatnības. Šī nodaļa pēta apstākļus, kas palīdzējuši žanra attīstībai Anglijā. Otrā nodaļa pievērš uzmanību Deivida Lodža liktenim, kas kā...

The Floating Upper Limb: Multiple Injuries Involving Ipsilateral, Proximal, Humeral, Supracondylar, and Distal Radial Limb.

Science.gov (United States)

Manaan, Qazi; Bashir, Adil; Zahoor, Adnan; Mokhdomi, Taseem A; Danish, Qazi

2016-09-01

Floating arm injury represents a common yet complicated injury of the childhood severely associated with limb deformation and even morbidity, if not precisely addressed and credibly operated. Here, we report a rare floating upper limb case of a 9-year-old boy with multiple injuries of ipsilateral proximal humeral, supracondylar and distal radial limb. This is the first report to document such a combined floating elbow and floating arm injury in the same limb. In this report, we discuss the surgical procedures used and recovery of the patient monitored to ascertain the effectiveness of the method in limb reorganisation.

Microclimate and architectural tectonic: vernacular floating house resilience in Seberang Ulu 1, Palembang

Science.gov (United States)

Puspitasari, P.; Kadri, T.; Indartoyo, I.; Kusumawati, L.

2018-01-01

This paper aims to describe the results of preliminary research on floating houses on the Musi River, Seberang Ulu 1, Palembang, focused on studying the influence of microclimates to the tectonics of Rumah Rakit (Floating House). The increase of water surface due to global warming will increase the need of using floating house typology in the future. The description of the inhabitants’ experiences on applying technics to create vernacular floating houses is considered as significant knowledge to develop advance technology on the basis of local characteristic. Vernacular floating houses resilience consists of natural experiences of inhabitants in adapting their daily activities to the characteristic of local climate. By using qualitative approach, the Rumah Rakit inhabitants’ verbal information in this article becomes the main aspect in exploring local knowledge. At the end, the conceptual model of vernacular Rumah Rakit in Seberang Ulu 1, Palembang is formulated, in terms of building architectural tectonic that is closely related to the local climate characteristic. The knowledge can be utilized in the context of rehabilitation or preservation of such architectural objects that are their existences tend to be extinct at this time.

Floating car data for traffic monitoring

DEFF Research Database (Denmark)

Torp, Kristian; Lahrmann, Harry Spaabæk

2005-01-01

This paper describes a complete prototype system that uses Floating Car Data (FCD) for both automatic and manual detection of queues in traffic. The system is developed under EU’s Tempo program. The systems consists of small hardware units placed in mobile traffic report units (we use taxis...

Research of design challenges and new technologies for floating LNG

Directory of Open Access Journals (Sweden)

Dong-Hyun Lee

2014-06-01

Full Text Available With the rate of worldwide LNG demand expected to grow faster than that of gas demand, most major oil companies are currently investing their resources to develop floating LNG-FLNG (i.e. LNG FSRU and LNG FPSO. The global Floating LNG (FLNG market trend will be reviewed based on demand and supply chain relationships. Typical technical issues associated with FLNG design are categorized in terms of global performance evaluation. Although many proven technologies developed through LNG carrier and oil FPSO projects are available for FLNG design, we are still faced with several technical challenges to clear for successful FLNG projects. In this study, some of the challenges encountered during development of the floating LNG facility (i.e. LNG FPSO and FSRU will be reviewed together with their investigated solution. At the same time, research of new LNG-related technologies such as combined containment system will be presented.

Experimental study on moonpool resonance of offshore floating structure

Directory of Open Access Journals (Sweden)

Seung-Ho Yang

2013-06-01

Full Text Available Offshore floating structures have so-called moonpool in the centre area for the purpose of drilling, installation of subsea structures, recovery of Remotely-Operated Vehicle (ROV and divers. However, this vertical opening has an effect on the operating performance of floating offshore structure in the vicinity of moonpool resonance frequency; piston mode and sloshing mode. Experimental study based on model test was carried out. Moonpool resonance of floating offshore structure on fixed condition and motion free condition were investigated. And, the effect of cofferdam which is representative inner structure inside moonpool was examined. Model test results showed that Molin's theoretical formula can predict moonpool resonance on fixed condition quite accurately. However, motion free condition has higher resonance frequency when it is compared with that of motion fixed. The installation of cofferdam moves resonance frequency to higher region and also generates secondary resonance at lower frequency. Furthermore, it was found that cofferdam was the cause of generating waves in the longitudinal direction when the vessel was in beam sea.

Floating liquid bridge charge dynamics

Science.gov (United States)

Teschke, Omar; Soares, David Mendez; Gomes, Whyllerson Evaristo; Valente Filho, Juracyr Ferraz

2016-01-01

The interaction of liquid with electric fields is investigated in a configuration where up to 13 kV are applied between electrodes resulting in a 106 V/m electric field in the capillaries and where there is the formation of a free-standing fluid bridge in the interelectrode gap. The Mott-Gurney equation was fitted to the measured ionization current vs applied voltage curve which indicates that the ionization rate at the high-voltage anode electrode dimethylsulfoxide (DMSO) interface and space charging in the interelectrode gap determine the floating liquid bridge current for a given cathode-to-anode voltage. Space charge effects were measured in the cathode becker and also at the liquid bridge since the ionized charges at the anode migrate to the bridge outer surface and decrease the interfacial tension from 43 mJ/m2 to 29 mJ/m2. Two distinct structural regions then form the bridge, a charged plastic (bulk modulus ˜100 MPa) conducting outer layer with a surface conductivity of ˜10-9 Ω-1, which shapes and supports the floating fluid structure, and an inner liquid cylinder, where DMSO molecules flow.

Optimal Configurations of Wave Energy Converter Arrays with a Floating Body

Directory of Open Access Journals (Sweden)

Zhang Wanchao

2016-10-01

Full Text Available An array of floating point-absorbing wave energy converters (WECs is usually employed for extracting efficiently ocean wave energy. For deep water environment, it is more feasible and convenient to connect the absorbers array with a floating body, such as a semi-submersible bottom-moored disk, whose function is to act as the virtual seabed. In the present work, an array of identical floating symmetrically distributed cylinders in a coaxial moored disk as a wave energy device is proposed The power take-off (PTO system in the wave energy device is assumed to be composed of a linear/nonlinear damper activated by the buoys heaving motion. Hydrodynamic analysis of the examined floating system is implemented in frequency domain. Hydrodynamic interferences between the oscillating bodies are accounted for in the corresponding coupled equations. The array layouts under the constraint of the disk, incidence wave directions, separating distance between the absorbers and the PTO damping are considered to optimize this kind of WECs. Numerical results with regular waves are presented and discussed for the axisymmetric system utilizing heave mode with these interaction factors, in terms of a specific numbers of cylinders and expected power production.

Frequency-domain characteristics of aerodynamic loads of offshore floating vertical axis wind turbines

DEFF Research Database (Denmark)

Borg, Michael; Collu, M.

2015-01-01

The re-emerging interest in vertical axis wind turbines for floating offshore applications has led to a need to investigate the relatively complex dynamics of such floating offshore structures. Through the use of a coupled model of dynamics this article investigates the frequency......-domain characteristics of floating vertical axis wind turbine aerodynamic loads. The impact of platform induced motion on aerodynamic loads is discussed in detail, with results indicating an increase in aerodynamic loads of several orders of magnitude over the range of frequencies usually containing significant wave...

Double optical gating

Science.gov (United States)

Gilbertson, Steve

The observation and control of dynamics in atomic and molecular targets requires the use of laser pulses with duration less than the characteristic timescale of the process which is to be manipulated. For electron dynamics, this time scale is on the order of attoseconds where 1 attosecond = 10 -18 seconds. In order to generate pulses on this time scale, different gating methods have been proposed. The idea is to extract or "gate" a single pulse from an attosecond pulse train and switch off all the other pulses. While previous methods have had some success, they are very difficult to implement and so far very few labs have access to these unique light sources. The purpose of this work is to introduce a new method, called double optical gating (DOG), and to demonstrate its effectiveness at generating high contrast single isolated attosecond pulses from multi-cycle lasers. First, the method is described in detail and is investigated in the spectral domain. The resulting attosecond pulses produced are then temporally characterized through attosecond streaking. A second method of gating, called generalized double optical gating (GDOG), is also introduced. This method allows attosecond pulse generation directly from a carrier-envelope phase un-stabilized laser system for the first time. Next the methods of DOG and GDOG are implemented in attosecond applications like high flux pulses and extreme broadband spectrum generation. Finally, the attosecond pulses themselves are used in experiments. First, an attosecond/femtosecond cross correlation is used for characterization of spatial and temporal properties of femtosecond pulses. Then, an attosecond pump, femtosecond probe experiment is conducted to observe and control electron dynamics in helium for the first time.

Multi detector computed tomography (MDCT) of the aortic root; ECG-gated verses non-ECG-gated examinations

International Nuclear Information System (INIS)

Kristiansen, Joanna; Guenther, Anne; Aalokken, Trond Mogens; Andersen, Rune

2011-01-01

Purpose: Motion artifacts may degrade a conventional CT examination of the ascending aorta and hinder accurate diagnosis. We quantitatively compared retrospectively electrocardiographic (ECG) -gated multi detector computed tomography (MDCT) with non-ECG-gated MDCT in order to demonstrate whether or not one of the methods should be preferred. Method: The study included seventeen patients with surgically reconstructed aortic root and reimplanted coronary arteries. All patients had undergone both non-gated MDCT and retrospectively ECG-gated MDCT employing a stringently modulated tube current with single phase image reconstruction. The incidence of motion artifacts in the left main coronary artery (LM), proximal right coronary artery (RCA), and aortic root and ascending aorta were rated using a four point scale. The effective dose for each scan was calculated and normalized to a 15 cm scan length. Statistical analysis of motion artifacts and radiation dose was performed using Wilcoxon matched pairs signed rank sum test. Results: A significant reduction in motion artifacts was found in all three vessels in images from the retrospectively ECG-gated scans (LM: P = 0.005, RCA: P = 0.015, aorta: P = 0.003). The mean normalized effective radiation dose was 3.69 mSv (±1.03) for the non-ECG-gated scans and 16.37 mSv (±2.53) for the ECG-gated scans. Conclusion: Retrospective ECG-gating with single phase reconstruction significantly reduces the incidence of motion artifacts in the aortic root and the proximal portion of the coronary arteries but at the expense of a fourfold increase in radiation dose.

Cardiac gated ventilation

International Nuclear Information System (INIS)

Hanson, C.W. III; Hoffman, E.A.

1995-01-01

There are several theoretic advantages to synchronizing positive pressure breaths with the cardiac cycle, including the potential for improving distribution of pulmonary and myocardial blood flow and enhancing cardiac output. The authors evaluated the effects of synchronizing respiration to the cardiac cycle using a programmable ventilator and electron beam CT (EBCT) scanning. The hearts of anesthetized dogs were imaged during cardiac gated respiration with a 50 msec scan aperture. Multi slice, short axis, dynamic image data sets spanning the apex to base of the left ventricle were evaluated to determine the volume of the left ventricular chamber at end-diastole and end-systole during apnea, systolic and diastolic cardiac gating. The authors observed an increase in cardiac output of up to 30% with inspiration gated to the systolic phase of the cardiac cycle in a non-failing model of the heart

[Five years of ROM in substance abuse treatment centres in the Netherlands].

Science.gov (United States)

Oudejans, S C C; Schippers, G M; Spits, M E; Stollenga, M; van den Brink, W

2012-01-01

Three substance abuse treatment centres set up a benchmarking project for routine outcome management (ROM) of structured cognitive behavioral treatments for outpatients with a substance use disorder. To present the results of five years benchmarking. All patients were included at intake and the follow-up assessment was performed by a call-center nine months later. Twice a year aggregated data were fed back to management and treatment teams. Since 2005, clinical outcome data, including substance abuse data, have been collected for more than half of all 15.786 treated patients. At follow-up, nine months after intake, 23% was abstinent, 28% reported moderate substance use and 49% reported excessive substance use. The Dutch centres for the treatment of substance abuse were successful in setting up ROM projects to monitor and compare the development and the effects of outpatient addiction treatments. The clinical results are acceptable and correspond to the results of the American project called match. It is not yet clear whether the biannual feedback of aggregated outcomes to management and treatment teams has contributed to the creation of learning organisations, but it has provided transparency and has made it possible for teams to learn from the outcomes.

LOYALTY – THE NUCLEUS OF BRAND CAPITAL. CASE STUDY: ROM CHOCOLATE BAR

Directory of Open Access Journals (Sweden)

Brindusa Mariana Amalancei

2013-12-01

Full Text Available It is considered that loyalty to the brand of some primary customers is the core of the brand capital. A brand, however, may have substantial value, which is given to it by its symbol and slogans, if it is continued with the purchase of a brand after the buyers have made a comparison with the competing products that have superior characteristics. Structured on several levels, which are each a different marketing challenge, the loyalty to the brand consists of many factors, among which the most important is the user experience. The paper aims to highlight, starting from a series of articles in online media, the manner in which a traditional Romanian brand, ROM chocolate bar, continuously repositions itself, attempting to maintain and even increase the loyalty of its consumers, as well as to answer the consumer’s authenticity, accessibility, credibility and modernity needs. Even though in specialized literature there are opinions according to which traditional brands are commonly old-fashioned or dull, ROM chocolate bar shows the opposite view, being considered a successful brand which is appreciated both at national and international levels.

Double-gated spectral snapshots for biomolecular fluorescence

International Nuclear Information System (INIS)

Nakamura, Ryosuke; Hamada, Norio; Ichida, Hideki; Tokunaga, Fumio; Kanematsu, Yasuo

2007-01-01

A versatile method to take femtosecond spectral snapshots of fluorescence has been developed based on a double gating technique in the combination of an optical Kerr gate and an image intensifier as an electrically driven gate set in front of a charge-coupled device detector. The application of a conventional optical-Kerr-gate method is limited to molecules with the short fluorescence lifetime up to a few hundred picoseconds, because long-lifetime fluorescence itself behaves as a source of the background signal due to insufficiency of the extinction ratio of polarizers employed for the Kerr gate. By using the image intensifier with the gate time of 200 ps, we have successfully suppressed the background signal and overcome the application limit of optical-Kerr-gate method. The system performance has been demonstrated by measuring time-resolved fluorescence spectra for laser dye solution and the riboflavin solution as a typical sample of biomolecule

Occupational Analysis Products: Operations Management- AFSC 3E6X1 (CD-ROM)

Science.gov (United States)

computer laser optical disc (CD-ROM); 4 3/4 in.; 23.4 MB. SYSTEMS DETAIL NOTE: ABSTRACT: This is a report of an occupational survey of the Operations ... Management (AFSC 3E6X1, OSSN 2560, Feb 04) career ladder, conducted by the Occupational Analysis Flight, AFOMS. The OSR reports the findings of current

Grid Simulator for Testing a Wind Turbine on Offshore Floating Platform

Energy Technology Data Exchange (ETDEWEB)

Gevorgian, V.

2012-02-01

An important aspect of such offshore testing of a wind turbine floating platform is electrical loading of the wind turbine generator. An option of interconnecting the floating wind turbine with the onshore grid via submarine power cable is limited by many factors such as costs and associated environmental aspects (i.e., an expensive and lengthy sea floor study is needed for cable routing, burial, etc). It appears to be a more cost effective solution to implement a standalone grid simulator on a floating platform itself for electrical loading of the test wind turbine. Such a grid simulator must create a stable fault-resilient voltage and frequency bus (a micro grid) for continuous operation of the test wind turbine. In this report, several electrical topologies for an offshore grid simulator were analyzed and modeled.

SOFIA - A simulation tool for bottom founded and floating offshore structures

DEFF Research Database (Denmark)

Nielsen, Morten Eggert; Ulriksen, Martin Dalgaard; Damkilde, Lars

2017-01-01

This paper presents a recently developed simulation tool, SOFIA (Simulation Of Floaters In Action), suitable for modeling slender bottom founded and moored/freely floating space frame structures exposed to environmental loads. In contrast to traditional rigid body formulations of floating...... and structure domains, which are coupled through the structural equation of motion. The structural domain is handled by means of the finite element method, while large displacements and stress stiffening effects, exhibited by moored floating structures, are inherently included due to a co-rotational element...... formulation. The fluid domain is modeled by an appropriate water wave theory, and the hydrodynamic loads are evaluated at the instantaneous fluid-structure interface by means of a relative Morison equation. The equation of motion is solved in time domain, which makes SOFIA capable of handling bottom founded...

Model-Based Control of a Ballast-Stabilized Floating Wind Turbine Exposed to Wind and Waves

DEFF Research Database (Denmark)

Christiansen, Søren

2013-01-01

wind turbine, for water depths beyond 50 meters where winds are stronger and less turbulent. A floating wind turbine is subject to not only aerodynamics and wind induced loads, but also to hy-drodynamics and wave induced loads. In contrast to a bottom fixed wind turbine, the floating structure......, the hydrodynamics and the loads change the dynamic behavior of a floating wind turbine. Consequently, conventional wind turbine control cause instabilities on floating wind turbines. This work addresses the control of a floating spar buoy wind turbine, and focuses on the impact of the additional platform dynamics....... A time varying control model is presented based on the wind speed and wave frequency. Estimates of the wind speed and wave frequency are used as scheduling variables in a gain scheduled linear quadratic controller to improve the electrical power production while reducing fatigue. To address the problem...

SEM REGRA NEM FREIOS - Loucura e criação na discussão romântica em torno do gênio

Directory of Open Access Journals (Sweden)

Yuri Cerqueira dos Anjos

2014-12-01

Full Text Available A relação entre genialidade e loucura, tópos bastante antigo, parece ganhar contornos peculiares no pensamento romântico. Inspirado, ultrassensível, isolado e visionário, o gênio romântico transita com certa frequência no campo semântico da loucura. Entre oráculo, profeta e louco, ele se caracteriza pela sua capacidade de transgredir o estado atual das coisas e criar um novo mundo de possibilidades e experiências. Nesse sentido, exploraremos no presente artigo alguns aspectos dessa relação entre o gênio e o louco no contexto do debate romântico francês do início do século XIX e no livro William Shakespeare, de Victor Hugo.

SU-E-T-350: Verification of Gating Performance of a New Elekta Gating Solution: Response Kit and Catalyst System

Energy Technology Data Exchange (ETDEWEB)

Xie, X; Cao, D; Housley, D; Mehta, V; Shepard, D [Swedish Cancer Institute, Seattle, WA (United States)

2014-06-01

Purpose: In this work, we have tested the performance of new respiratory gating solutions for Elekta linacs. These solutions include the Response gating and the C-RAD Catalyst surface mapping system.Verification measurements have been performed for a series of clinical cases. We also examined the beam on latency of the system and its impact on delivery efficiency. Methods: To verify the benefits of tighter gating windows, a Quasar Respiratory Motion Platform was used. Its vertical-motion plate acted as a respiration surrogate and was tracked by the Catalyst system to generate gating signals. A MatriXX ion-chamber array was mounted on its longitudinal-moving platform. Clinical plans are delivered to a stationary and moving Matrix array at 100%, 50% and 30% gating windows and gamma scores were calculated comparing moving delivery results to the stationary result. It is important to note that as one moves to tighter gating windows, the delivery efficiency will be impacted by the linac's beam-on latency. Using a specialized software package, we generated beam-on signals of lengths of 1000ms, 600ms, 450ms, 400ms, 350ms and 300ms. As the gating windows get tighter, one can expect to reach a point where the dose rate will fall to nearly zero, indicating that the gating window is close to beam-on latency. A clinically useful gating window needs to be significantly longer than the latency for the linac. Results: As expected, the use of tighter gating windows improved delivery accuracy. However, a lower limit of the gating window, largely defined by linac beam-on latency, exists at around 300ms. Conclusion: The Response gating kit, combined with the C-RAD Catalyst, provides an effective solution for respiratorygated treatment delivery. Careful patient selection, gating window design, even visual/audio coaching may be necessary to ensure both delivery quality and efficiency. This research project is funded by Elekta.

Integrated simulation challenges with the DeepWind floating vertical axis wind turbine concept

DEFF Research Database (Denmark)

Verelst, David; Aagaard Madsen, Helge; Borg, Michael

2015-01-01

This paper presents the experiences and challenges with concurrently carrying out numerical model development, integrated simulations and design of a novel floating vertical axis wind turbine, the DeepWind concept. The floating VAWT modelling capabilities of the aero-hydro-elastic HAWC2 simulation...

Voltage-Gated Potassium Channels: A Structural Examination of Selectivity and Gating

Science.gov (United States)

Kim, Dorothy M.; Nimigean, Crina M.

2016-01-01

Voltage-gated potassium channels play a fundamental role in the generation and propagation of the action potential. The discovery of these channels began with predictions made by early pioneers, and has culminated in their extensive functional and structural characterization by electrophysiological, spectroscopic, and crystallographic studies. With the aid of a variety of crystal structures of these channels, a highly detailed picture emerges of how the voltage-sensing domain reports changes in the membrane electric field and couples this to conformational changes in the activation gate. In addition, high-resolution structural and functional studies of K+ channel pores, such as KcsA and MthK, offer a comprehensive picture on how selectivity is achieved in K+ channels. Here, we illustrate the remarkable features of voltage-gated potassium channels and explain the mechanisms used by these machines with experimental data. PMID:27141052

Audio-visual biofeedback for respiratory-gated radiotherapy: Impact of audio instruction and audio-visual biofeedback on respiratory-gated radiotherapy

International Nuclear Information System (INIS)

George, Rohini; Chung, Theodore D.; Vedam, Sastry S.; Ramakrishnan, Viswanathan; Mohan, Radhe; Weiss, Elisabeth; Keall, Paul J.

2006-01-01

Purpose: Respiratory gating is a commercially available technology for reducing the deleterious effects of motion during imaging and treatment. The efficacy of gating is dependent on the reproducibility within and between respiratory cycles during imaging and treatment. The aim of this study was to determine whether audio-visual biofeedback can improve respiratory reproducibility by decreasing residual motion and therefore increasing the accuracy of gated radiotherapy. Methods and Materials: A total of 331 respiratory traces were collected from 24 lung cancer patients. The protocol consisted of five breathing training sessions spaced about a week apart. Within each session the patients initially breathed without any instruction (free breathing), with audio instructions and with audio-visual biofeedback. Residual motion was quantified by the standard deviation of the respiratory signal within the gating window. Results: Audio-visual biofeedback significantly reduced residual motion compared with free breathing and audio instruction. Displacement-based gating has lower residual motion than phase-based gating. Little reduction in residual motion was found for duty cycles less than 30%; for duty cycles above 50% there was a sharp increase in residual motion. Conclusions: The efficiency and reproducibility of gating can be improved by: incorporating audio-visual biofeedback, using a 30-50% duty cycle, gating during exhalation, and using displacement-based gating

Impact of floating windows on the accuracy of depth perception in games

Science.gov (United States)

Stanfield, Brodie; Zerebecki, Christopher; Hogue, Andrew; Kapralos, Bill; Collins, Karen

2013-03-01

The floating window technique is commonly employed by stereoscopic 3D filmmakers to reduce the effects of window violations by masking out portions of the screen that contain visual information that doesn't exist in one of the views. Although widely adopted in the film industry, and despite its potential benefits, the technique has not been adopted by video game developers to the same extent possibly because of the lack of understanding of how the floating window can be utilized in such an interactive medium. Here, we describe a quantitative study that investigates how the floating window technique affects users' depth perception in a simple game-like environment. Our goal is to determine how various stereoscopic 3D parameters such as the existence, shape, and size of the floating window affect the user experience and to devise a set of guidelines for game developers wishing to develop stereoscopic 3D content. Providing game designers with quantitative knowledge of how these parameters can affect user experience is invaluable when choosing to design interactive stereoscopic 3D content.

Improvement of Network Performance by In-Vehicle Routing Using Floating Car Data

Directory of Open Access Journals (Sweden)

Gerdien A. Klunder

2017-01-01

Full Text Available This paper describes a study which gives insight into the size of improvement that is possible with individual in-car routing advice based on the actual traffic situation derived from floating car data (FCD. It also gives an idea about the required penetration rate of floating car data needed to achieve a certain degree of improvement. The study uses real loop detector data from the region of Amsterdam collected for over a year, a route generating algorithm for in-car routing advice, and emulated floating car data to generate the routing advice. The case with in-car routing advice has been compared to the base case, where drivers base their routing decisions on average knowledge of travel times in the network. The improvement in total delay using the in-vehicle system is dependent on penetration rate and accuracy of the floating car data and varies from 2.0% to 3.4% for 10% penetration rate. This leads to yearly savings of about 15 million euros if delay is monetarised using standard prices for value of time (VOT.

Wake losses optimization of offshore wind farms with moveable floating wind turbines

International Nuclear Information System (INIS)

Rodrigues, S.F.; Teixeira Pinto, R.; Soleimanzadeh, M.; Bosman, Peter A.N.; Bauer, P.

2015-01-01

Highlights: • We present a layout optimization framework for wind farms with moveable turbines. • Using moveable wind turbines in optimized layouts maximizes energy production. • Turbine and wind farm designers should cooperate to optimize offshore wind projects. - Abstract: In the future, floating wind turbines could be used to harvest energy in deep offshore areas where higher wind mean speeds are observed. Currently, several floating turbine concepts are being designed and tested in small scale projects; in particular, one concept allows the turbine to move after installation. This article presents a novel layout optimization framework for wind farms composed of moveable floating turbines. The proposed framework uses an evolutionary optimization strategy in a nested configuration which simultaneously optimizes the anchoring locations and the wind turbine position within the mooring lines for each individual wind direction. The results show that maximum energy production is obtained when moveable wind turbines are deployed in an optimized layout. In conclusion, the framework represents a new design optimization tool for future offshore wind farms composed of moveable floating turbines

Prospect of floating desalination facilities using nuclear energy in Indonesia

International Nuclear Information System (INIS)

Rusli, A.; Rina, G.; Gunandjar; Subki, I.R.

1997-01-01

This paper summarizes studies on the water demand and supply problems in Indonesia in the last few years. During the dry season in 1990, it was reported that lack of fresh drinking water in Java and Bali amounted to 2.4 x 10 6 ton/month. Since Indonesia consists of more than 13,000 islands, more problems are faced by other islands. The studies are focused on certain regions (groups of islands) which may have a potential for using a floating desalination facility. Water reservoirs in each island and delivery systems from the floating desalination facilities need to be assessed to see the prospective uses of the systems. Cheap, self-forgiving and easily operated systems, using transportable ship mounted desalination facilities, may be required as a solution to the water supply shortages for these islands. Conclusions based on current problems in water demand and supply and comments on the prospective future market using floating desalination facilities in Indonesia are also given. (author). 9 refs, 10 tabs

Are the older ARGO-Floats more vulnerable to Fouling and Associated Salinity drift compared to that of later deployments?

Digital Repository Service at National Institute of Oceanography (India)

Pankajakshan, T.; Youn, Y.H.; Lee, H.

in different years Floats deployed in the East/Japan Sea and in the Indian Ocean are examined to find out float-to-float match-ups in such a way that an older float pops up simultaneously with a newer deployment (with tolerable space-time difference) A time...

Floating convection barrier for evaporation source

International Nuclear Information System (INIS)

1975-01-01

A floating matrix of titanium in an uranium evaporation source, melted by an electron beam, serves as a barrier for preventing cooler material from reaching the evaporation area. This construction allows a big volume of melted uranium to be present and new uranium to be furnished in regulated intervals without manual intervention

Evaluation of the use of CD-ROM upload into the PACS or institutional web server

NARCIS (Netherlands)

van Ooijen, P. M. A.; Roosjen, R.; de Blecourt, M. J.; van Dam, R.; Broekema, A.; Oudkerk, M.

2006-01-01

Purpose: Patient data are increasingly distributed between hospitals using CD-ROMs instead of actual films. This introduces problems because different viewers from different vendors are provided, and sometimes viewers are unusable because local software installation is not allowed. In 2004, we

Image quality in non-gated versus gated reconstruction of tongue motion using magnetic resonance imaging: a comparison using automated image processing

Energy Technology Data Exchange (ETDEWEB)

Alvey, Christopher; Orphanidou, C.; Coleman, J.; McIntyre, A.; Golding, S.; Kochanski, G. [University of Oxford, Oxford (United Kingdom)

2008-11-15

The use of gated or ECG triggered MR is a well-established technique and developments in coil technology have enabled this approach to be applied to areas other than the heart. However, the image quality of gated (ECG or cine) versus non-gated or real-time has not been extensively evaluated in the mouth. We evaluate two image sequences by developing an automatic image processing technique which compares how well the image represents known anatomy. Four subjects practised experimental poly-syllabic sentences prior to MR scanning. Using a 1.5 T MR unit, we acquired comparable gated (using an artificial trigger) and non-gated sagittal images during speech. We then used an image processing algorithm to model the image grey along lines that cross the airway. Each line involved an eight parameter non-linear equation to model of proton densities, edges, and dimensions. Gated and non-gated images show similar spatial resolution, with non-gated images being slightly sharper (10% better resolution, less than 1 pixel). However, the gated sequences generated images of substantially lower inherent noise, and substantially better discrimination between air and tissue. Additionally, the gated sequences demonstrate a very much greater temporal resolution. Overall, image quality is better with gated imaging techniques, especially given their superior temporal resolution. Gated techniques are limited by the repeatability of the motions involved, and we have shown that speech to a metronome can be sufficiently repeatable to allow high-quality gated magnetic resonance imaging images. We suggest that gated sequences may be useful for evaluating other types of repetitive movement involving the joints and limb motions. (orig.)