WorldWideScience

Sample records for flash smelting process

  1. Waste Heat Recovery and Utilization of Copper Smelting Flash Smelting and Flash Converting Process%铜冶炼"双闪"工艺中余热回收及利用

    Institute of Scientific and Technical Information of China (English)

    鞠霞

    2015-01-01

    Based on upgrading and renovation engineering of a certain non-ferrous copper smelting process technology, the paper discusses flue gas heat waste recovery efficiency and waste heat recovery device of flash smelting furnace, flash converting furnace in copper smelting flash smelting and flash converting process, introduces waste heat utilization system, and puts forward advantages and disadvantages of the waste heat utilization system.%基于某有色铜冶炼工艺技术升级改造工程,论述了铜冶炼"双闪"工艺中闪速熔炼炉、闪速吹炼炉烟气余热回收效率及余热回收装置,介绍了余热利用系统,并指出该余热利用系统的优缺点.

  2. Modelling of chalcopyrite oxidation reactions in the Outokumpu flash smelting process

    Energy Technology Data Exchange (ETDEWEB)

    Ahokainen, T.; Jokilaakso, A. [Helsinki Univ. of Technology, Otaniemi (Finland)

    1996-12-31

    A mathematical model for simulating oxidation reactions of chalcopyrite particles together with momentum, heat and mass transfer between particle and gas phase in a flash smelting furnace reaction shaft is presented. In simulation, the equations governing the gas flow are solved numerically with a commercial fluid flow package, Phoenics. The particle phase is introduced into the gas flow by a Particle Source In Cell (PSIC) - technique, where a number of discrete particles is tracked in a gas flow and the relevant source terms for momentum, mass, and heat transfer are added to the gas phase equations. The gas phase equations used are elliptic in nature and the fluid turbulence is described by the (k-{epsilon}) -model. Thermal gas phase radiation is simulated with a six-flux radiation model. The chemical reactions of concentrate particles are assumed to happen at two sharp interfaces, and a shrinking core model is applied to describe the mass transfer of chemical species through the reaction product layer. In a molten state, the oxygen consumption is controlled by a film penetration concept. The reacting concentrate particles are a mixture of chalcopyrite and silica. Also a certain amount of pure inert silica is fed to the process as flux. In the simulations the calculation domain includes the concentrate burner and a cylindrical reaction shaft of an industrial scale flash smelting furnace. Some examples about the simulations carried out by the combustion model are presented. (author)

  3. Influence of operation parameters on flash smelting furnace based on CFD

    Institute of Scientific and Technical Information of China (English)

    Xinfeng Li; Shiheng Peng; Xiangli Han; Chi Mei; Tianyuan Xiao

    2004-01-01

    The influence of three important operation parameters in Jinlong flash smelting furnace, including the distributing blast speed, the oxygen enrichment rate of process air and the ratio of central oxygen to overall oxygen (Oc/Oo), has been investigated using a virtual simulation system on copper flash smelting furnace. The core of this virtual simulation system is a numerical simulation of CFD (computational fluid dynamics), and this system incorporates coupling momentum transport, heat transport, mass transport,reaction kinetics between gas and particles and chemical reactions between gas and gas. A set of numerical predicted data were obtained. The CFD simulation shows that there is a sensitive zone of the distributing blast speed, and the dust content ascends when the speed exceeds 180 m-s-1. Increasing the oxygen concentration of processing air benefits the efficient production of the flash smelting furnace.

  4. From Sulfide Flash Smelting to a Novel Flash Ironmaking Technology

    Science.gov (United States)

    Sohn, Hong Yong

    A novel flash ironmaking technology is under development at the University of Utah under the support of U.S. Department of Energy (DOE) and American Iron and Steel Institute (AISI). The history of the development from the conception of the idea to the current status will be discussed. The flash ironmaking process produces iron directly from fine iron ore concentrates without requiring cokemaking and pelletization/sintering, which will enable the technology to significantly reduce energy consumption and carbon dioxide emissions compared with blast furnace ironmaking. Unlike other gas-based ironmaking processes, this technology will not suffer from the problems of solid sticking and fusion. Current work is focused on the method of supplying the energy required to maintain the necessary temperature, as an intermediate step to determine the scalability for larger, industrial-scale pilot trials.

  5. 硫化铅矿闪速熔炼过程的热力学分析%Thermodynamic analysis of lead sulfide flash smelting process

    Institute of Scientific and Technical Information of China (English)

    汪金良; 张文海; 张传福

    2011-01-01

    Based on the principle of Gibbs free energy minimization, the thermodynamic model of the lead sulfide flash smelting multi-phase equilibrium system was built. Then, the effects of the smelting temperature (7) and the oxygen volume per ton ore (Povpto) on the lead distribution rate and the equilibrium compositions of crude lead, slag and gas were studied. The results show that, for the lead sulfide with a certain amount and a certain composition, the sulfur content in the crude lead can be reduced to be less than 0.1% with the rise of T and Fovpto, but the lead content in the slag exceeds 60% and the lead distribution rate in the crude lead is less than 30% when Fovpto is excessive. The lead volatile in the gas, mainly in the form of PbS, rises with the rise of T and the decrease of Kovpto- Therefore, taking into account the recovery rate of lead and the processing difficulty of products, the lead flash direct smelting furnace should be divided into oxidation and reduction zones, and the low-sulfur lead is produced firstly in the oxidation zone, the low-lead slag is produced secondly in the later zone, and the oxidation smelting temperature should be low.%基于最小吉布斯自由能原理,建立硫化铅矿闪速熔炼过程多相平衡热力学模型,考察熔炼温度(T)、吨矿氧量(VOVPTO)对粗铅含硫量、炉渣含铅量、烟气含铅量及铅在各平衡相中分配比的影响.结果表明:对一定用量和一定成分的硫化铅矿,随着7和VOVPTO的增大,粗铅含硫量可降至0.1%(质量分数)以下,但过高的VOVPTO会使渣含铅量升至60%(质量分数)以上,铅在粗铅中的分配比低于30%(质量分数);烟气中的铅主要以PbS形式存在,其含量随着7的升高及VOVPTO降低而增高.综合考虑铅的直收率及产物处理的难易程度,闪速炉直接炼铅应采取分区分步熔炼方式,先在氧化区制“低硫铅”,然后在还原区造“低铅渣”,且氧化区熔炼温度宜较低.

  6. Effects of a reducer type on copper flash smelting slag decopperisation

    Directory of Open Access Journals (Sweden)

    B. Oleksiak

    2015-01-01

    Full Text Available In the paper, results of investigations on coke dust, anthracite dust and coal flotation concentrate application in the technology of copper flash smelting slag processing are presented. The results show that the selected reducers can be used as substitutes for the conventional coke.

  7. Numerical simulation analysis of Guixi copper flash smelting furnace

    Institute of Scientific and Technical Information of China (English)

    2002-01-01

    A numerical simulation analysis for reactions of chalcopyrite and pyrite particles coupled with momentum, heat and mass transfer between the particle and gas in a flash smelting furnace is presented. In the simulation, the equations governing the gas flow are solved numerically by Eular method. The particle phase is introduced into the gas flow by the particle-source-in-cell technique (PSIC). Predictions including the fluid flow field, temperature field, concentration field of gas phase and the tracks of particles have been obtained by the numerical simulation. The visualized results show that the reaction of sulfide particles is almost completed in the upper zone of the shaft within 1.5 m far from the central jet distributor (CJD) type concentrate burner. The simulation results are in good agreement with data obtained from a series of experiments and tests in the plant and the error is less than 2%.

  8. Numerical modeling of Jinlong CJD burner copper flash smelting furnace

    Institute of Scientific and Technical Information of China (English)

    2002-01-01

    Fluid flow, heat transfer and combustion in Jinlong CJD concentrate burner flash smelting furnace have been investigated by numerical modeling and flow visualization. The modeling is based on the Eulerian approach for the gas flow equations and the Lagrangian approach for the particles. Interaction between the gas phase and particle phase, such as frictional forces, heat and mass transfer, are included by the addition of sources and sinks. The modeling results including the fluid flow field, temperature field, concentration field of gas phase and the trajectories of particles have been obtained. The predicted results are in good agreement with the data obtained from a series of experiments and tests in the Jinlong Copper Smelter and the temperature error is less than 20 K.

  9. The aluminum smelting process.

    Science.gov (United States)

    Kvande, Halvor

    2014-05-01

    This introduction to the industrial primary aluminum production process presents a short description of the electrolytic reduction technology, the history of aluminum, and the importance of this metal and its production process to modern society. Aluminum's special qualities have enabled advances in technologies coupled with energy and cost savings. Aircraft capabilities have been greatly enhanced, and increases in size and capacity are made possible by advances in aluminum technology. The metal's flexibility for shaping and extruding has led to architectural advances in energy-saving building construction. The high strength-to-weight ratio has meant a substantial reduction in energy consumption for trucks and other vehicles. The aluminum industry is therefore a pivotal one for ecological sustainability and strategic for technological development.

  10. Simulation of moving boundary of the reaction shaft in a flash smelting furnace

    Institute of Scientific and Technical Information of China (English)

    2001-01-01

    As to solve the online monitoring of the inner temperature and freezing profile of the reaction shaft of flash smelting furnace, simulation of the wall in the reaction shaft in a flash smelting furnace was made through numerical computation. The computational results are very near the data got in site. The error of the moving boundary is approximately 3 %, and that of the temperature is less than 5 %. It is proved that the simulation software is applicable for practice to monitor the temperature and moving boundary inside the hearth online. Based on a large number of the data computed, the relation between the change of the moving boundary and inner temperature is summarized, and the great influence of the cooling system on the forming and stability of the moving boundary inside the hearth is emphasized, which provide the theoretical bases for optimizing the flash smelting operation.

  11. 铅富氧闪速熔炼的整体运行效果及评价%Production Status and Evaluation of Lead Oxygen-Enriched Flash Smelting Process

    Institute of Scientific and Technical Information of China (English)

    王成彦; 郜伟; 尹飞; 宋元张; 郑晓斌; 梁德华; 李强

    2012-01-01

    2011年5月10日,年产10万t粗铅的铅富氧闪速熔炼工程正式投料生产.在入炉料含铅25%~30%的情况下,取得了一次铅还原率大于85%、铅总回收率98.5%、金银回收率大于99.5%、铜回收率大于85%、锌回收率大于90%、脱硫率大于98%的指标;取消烟化炉,真正实现了铅、锌的一次回收;包括还原贫化电炉挥发锌的能耗在内,吨粗铅综合能耗约为213 kgce;弃渣含铅、锌小于2%(最低小于1%)、平均含银小于6 g/t、含金小于0.1 g/t、含铜小于0.1%;产出的氧化锌灰不含氟、氯,可以不经多膛炉脱氟氯而直接送锌冶炼厂回收锌.工业生产中取得的多项技术经济指标表明,铅富氧闪速熔炼新技术已经达到世界领先水平.%The first lead oxygen-enriched flash smelting plant in China, with an annual capacity of 100 kt of lead bullion, was successfully put into production on May 10, 2011. With the use of charging materials with 25%~30% lead content, it performed satisfactory technical and economical indexes,that is, the primary reduction rate of lead is more than 85%, the metal recovery rates of Pb, Au & Ag, Cu and Zn are > 98. 5%, >99. 5%, >85% and >90%, respectively, with the desulfurization rate over 98%. One-step recovering Pb &. Zn technique was realized due to cancel fuming furnace. The comprehensive energy consumption of crude lead, including the energy consumption of zinc volatilization in the reduction furnace, was about 213 kgce/t. Waste slag with Pb &. Zn <2% (average <1%), Ag<6 g/t, Au<0. 1 g/t, and Cu<0. 1% was produced. With no fluorine and chlorine,zinc oxide ash can be sent to zinc smelting plant directly to recover zinc without defluorination and dechlorination in multi-hearth furnace. Several technical and economic indexes obtained from the industry production show that lead oxygen-enriched flash smelting process has reached the leadership of world level.

  12. Reaction Mechanism and Distribution Behavior of Arsenic in the Bottom Blown Copper Smelting Process

    Directory of Open Access Journals (Sweden)

    Qinmeng Wang

    2017-08-01

    Full Text Available The control of arsenic, a toxic and carcinogenic element, is an important issue for all copper smelters. In this work, the reaction mechanism and distribution behavior of arsenic in the bottom blown copper smelting process (SKS process were investigated and compared to the flash smelting process. There are obvious differences of arsenic distribution in the SKS process and flash process, resulting from the differences of oxygen potentials, volatilizations, smelting temperatures, reaction intensities, and mass transfer processes. Under stable production conditions, the distributions of arsenic among matte, slag, and gas phases are 6%, 12%, and 82%, respectively. Less arsenic is reported in the gas phase with the flash process than with the SKS process. The main arsenic species in gas phase are AsS (g, AsO (g, and As2 (g. Arsenic exists in the slag predominantly as As2O3 (l, and in matte as As (l. High matte grade is harmful to the elimination of arsenic to gas. The changing of Fe/SiO2 has slight effects on the distributions of arsenic. In order to enhance the removal of arsenic from the SKS smelting system to the gas phase, low oxygen concentration, low ratios of oxygen/ore, and low matte grade should be chosen. In the SKS smelting process, no dust is recycled, and almost all dust is collected and further treated to eliminate arsenic and recover valuable metals by other process streams.

  13. A thermodynamic model of nickel smelting and direct high-grade nickel matte smelting processes: Part I. Model development and validation

    Science.gov (United States)

    Tan, Pengfu; Neuschütz, Dieter

    2001-04-01

    A thermodynamic model has been developed to predict the distribution behavior of Ni, Cu, Co, Fe, S, As, Sb, and Bi in the Outokumpu flash-smelting process, the Outokumpu direct high-grade matte smelting process, and the INCO flash-smelting process. In this model, as many as 16 elements (Ni, Cu, Co, Fe, As, Sb, Bi, S, O, Al, Ca, Mg, Si, N, C, and H) are considered, and two nickel sulfide species are used to allow for modeling of sulfur-deficient mattes. The compositions of the matte, slag, and gaseous phases in equilibrium are calculated using Gibbs free energies of formation and the activity coefficients of the components derived from the experimental data. The model predictions are compared with the known industrial data from the Kalgoorlie Nickel Smelter (Kalgoorlie, Australia), the Outokumpu Harjavalta Nickel Smelter (Harjavalta, Finland), the INCO Metals Company (Sudbury, Canada), and from a number of experimental data. An excellent agreement is obtained. It was found that the distribution behaviors of Ni, Co, Cu, Fe, S, As, Sb, and Bi in the nickel smelting furnace depend on process parameters such as the smelting temperature, matte grade, and partial pressure of oxygen in the process.

  14. Recovery of Copper from the Slag of Khatoonabad Flash Smelting Furnace by Flotation Method

    Science.gov (United States)

    Karimi, Nader; Vaghar, Ramez; Mohammadi, Mohammad Reza Tavakoli; Hashemi, Seyed Ahmad

    2013-04-01

    Copper loss in the slag of Khatoonabad flash smelting furnace is estimated to be about 1-3 %. At present, the electric slag cleaning furnace is used for the recovery of copper from slag. However, due to low recovery efficiency of electric furnace along with high consumption of electrical energy and water, selection of a method to enable minimum energy consumption and maximum recovery of copper seems to be essential. Therefore, the aim of this study was to investigate the possibility of copper recovery from this slag using flotation method, and to determine the effective parameters involved in the process. Based on the experiments conducted, the best results were obtained for pH 11.5, 60 g/t Z11 and R407 collectors with a weighing ratio of 3-2, 40 g/t of MIBC and A65 frothers with an equal weighting ratio and grinding time of 45 min. Under these conditions, the copper concentrate grade and recovery were 19 and 91.1 % in the rougher step, 27.4 and 96.3 % in the cleaner step, and 32 and 93 % in the recleaner step, respectively.

  15. Measurements of oxygen pressure in a copper flash smelting furnace by an EMF method

    Science.gov (United States)

    Kemori, Nobumasa; Shibata, Yukio; Tomono, Mutsuo

    1986-01-01

    Oxygen pressures in a copper flash smelting furnace were measured by means of the following galvanic cell: Fe, FeO/ZrO2 + MgO/ barO in slag or matte. Measured oxygen pressures were normalized to 1523 K with respect to the reaction: 4 FeO(l) + O2(g) = 4 FeO1.5(l). Vertical and horizontal variations of normalized oxygen pressures in the reaction shaft and in the settler were studied. The equilibrium relation between normalized oxygen pressure and the ratio of ferric to ferrous oxide content in the furnace slag was confirmed, and the activity coefficient ratio of these oxides was determined.

  16. Flash Lidar Data Processing

    Science.gov (United States)

    Bergkoetter, M. D.; Ruppert, L.; Weimer, C. S.; Ramond, T.; Lefsky, M. A.; Burke, I. C.; Hu, Y.

    2009-12-01

    Late last year, a prototype Flash LIDAR instrument flew on a series of airborne tests to demonstrate its potential for improved vegetation measurements. The prototype is a precursor to the Electronically Steerable Flash LIDAR (ESFL) currently under development at Ball Aerospace and Technology Corp. with funding from the NASA Earth Science Technology Office. ESFL may soon significantly expand our ability to measure vegetation and forests and better understand the extent of their role in global climate change and the carbon cycle - all critical science questions relating to the upcoming NASA DESDynI and ESA BIOMASS missions. In order to more efficiently exploit data returned from the experimental Flash Lidar system and plan for data exploitation from future flights, Ball funded a graduate student project (through the Ball Summer Intern Program, summer 2009) to develop and implement algorithms for post-processing of the 3-Dimensional Flash Lidar data. This effort included developing autonomous algorithms to resample the data to a uniform rectangular grid, geolocation of the data, and visual display of large swaths of data. The resampling, geolocation, surface hit detection, and aggregation of frame data are implemented with new MATLAB code, and the efficient visual display is achieved with free commercial viewing software. These efforts directly support additional tests flights planned as early as October 2009, including possible flights over Niwot Ridge, CO, for which there is ICESat data, and a sea-level coastal area in California to test the effect of higher altitude (above ground level) on the divergence of the beams and the beam spot sizes.

  17. Mathematical modeling of the flash converting process

    Energy Technology Data Exchange (ETDEWEB)

    Sohn, H.Y.; Perez-Tello, M.; Riihilahti, K.M. [Utah Univ., Salt Lake City, UT (United States)

    1996-12-31

    An axisymmetric mathematical model for the Kennecott-Outokumpu flash converting process for converting solid copper matte to copper is presented. The model is an adaptation of the comprehensive mathematical model formerly developed at the University of Utah for the flash smelting of copper concentrates. The model incorporates the transport of momentum, heat, mass, and reaction kinetics between gas and particles in a particle-laden turbulent gas jet. The standard k-{epsilon} model is used to describe gas-phase turbulence in an Eulerian framework. The particle-phase is treated from a Lagrangian viewpoint which is coupled to the gas-phase via the source terms in the Eulerian gas-phase governing equations. Matte particles were represented as Cu{sub 2}S yFeS, and assumed to undergo homogeneous oxidation to Cu{sub 2}O, Fe{sub 3}O{sub 4}, and SO{sub 2}. A reaction kinetics mechanism involving both external mass transfer of oxygen gas to the particle surface and diffusion of oxygen through the porous oxide layer is proposed to estimate the particle oxidation rate Predictions of the mathematical model were compared with the experimental data collected in a bench-scale flash converting facility. Good agreement between the model predictions and the measurements was obtained. The model was used to study the effect of different gas-injection configurations on the overall fluid dynamics in a commercial size flash converting shaft. (author)

  18. Recirculation of Chilean copper smelting dust with high impurities contents to the smelting process

    Energy Technology Data Exchange (ETDEWEB)

    Sano, H.; Fujisawa, T. [Nagoya Univ., Nagoya (Japan). EcoTopia Science Inst.; Montenegro, V. [Nagoya Univ., Nagoya (Japan). Dept. of Materials Science and Engineering

    2007-07-01

    Dust generated during the copper smelting process is generally stabilized using hydrometallurgical methods as it contains high concentrations of arsenic. In this laboratory study, dust was recirculated during the smelting process in order to recover more copper and decrease dust emissions while recovering more copper. The behaviour of impurities and their influence on matte quality was also investigated. Industrial matte, flue dust, slag, and copper concentrates from a Chilean smelter were used as test materials. Dust recirculation tests were conducted in a simulated electric furnace. Off-gases were collected in a reaction tube, and the condensed volatile matter, slag, and matte phases were analyzed for their elemental content by inductively coupled plasma atomic emission spectrometry. The distribution of arsenic (As); antimony (Sb), bismuth (Bi), lead (Pb), and zinc (Zn) were investigated by varying the amounts of dust recirculating to the smelting stage with 21 per cent of the oxygen. Results showed that distributions of all analyzed elements increased with recirculation. It was concluded that copper can be recovered using the dust recirculation technique. However, impurities may limit the efficacy of the dust recirculation process. 6 refs., 3 tabs., 4 figs.

  19. Intelligent Fault Diagnosis in Lead-zinc Smelting Process

    Institute of Scientific and Technical Information of China (English)

    Wei-Hua Gui; Chun-Hua Yang; Jing Teng

    2007-01-01

    According to the fault characteristic of the imperial smelting process (ISP), a novel intelligent integrated fault diagnostic system is developed. In the system fuzzy neural networks are utilized to extract fault symptom and expert system is employed for effective fault diagnosis of the process. Furthermore, fuzzy abductive inference is introduced to diagnose multiple faults. Feasibility of the proposed system is demonstrated through a pilot plant case study.

  20. Thermodynamic Modeling of Arsenic in Copper Smelting Processes

    Science.gov (United States)

    Chen, Chunlin; Zhang, Ling; Jahanshahi, Sharif

    2010-12-01

    Published data on the activity coefficients of arsenic in liquid copper, matte and, slag have been reviewed, assessed, and used in the development of thermodynamic databases for solution models of melts. The databases were validated against the literature data on the equilibrium distribution of arsenic between the matte and the slag. The models and databases were used in investigating the effects of matte grade, slag chemistry, SO2 partial pressure, arsenic loading, and temperature on the equilibrium distribution of arsenic between the melts and gas phase during copper smelting and converting. The results obtained show that the continuous smelting processes operates close to equilibrium between condensed phases with most arsenic reporting to the gas phase. A comparison of the batch and continuous converting processes showed a considerable difference with respect to the elimination of the arsenic from condensed phases. These results indicate batch processes to be more efficient in the removal of arsenic through the gas stream.

  1. Development of Direct Reduction Process and Smelting Reduction Processes for the Steel Production

    Directory of Open Access Journals (Sweden)

    Kožuh S.

    2006-01-01

    Full Text Available Although the blast furnace and basic oxygen furnace are going to be primary routes for steel production in future, the steelmaking industry using the electric arc furnace route will continue to grow. The importance of high-quality steel products manufactured by direct reduction of iron ore and/or by smelting reduction processes has been increasing. In the past decade the world steel production by direct reduction rose by 140 per cent, from about 20 to about 49.5 Mt/year. In this paper major industrial processes involving direct reduction and smelting reduction of iron ore are described, and their development is analysed.

  2. Recirculation effect of Chilean copper smelting dust with high impurities contents on the impurity distributions during smelting process; Efecto de la recirculacion de polvo de fundicion de cobre de Chile con altos contenidos de impurezas en la distribucion de impurezas durante el proceso de fusion

    Energy Technology Data Exchange (ETDEWEB)

    Montenegro, V.; Sano, H.; Fujisawa, T.

    2010-07-01

    Usually, dust generated during the copper smelting process by the Teniente Converter and the Flash Smelting Furnaces in Chile, contains high concentrations of copper, zinc, arsenic, antimony and other metals. In general, the dust is recirculated to the smelting process or it is directed to hydrometallurgical process for recovery and stabilization. However, in recent years the generation of dust has increased because of the degradation of the quality of the concentrate. In addition, the environmental regulations have become stricter. It is therefore desirable to understand the behavior of those elements, when the smelting process operates with recirculation of dust. In this study, the effect of dust recirculation to smelting process on the distribution among the matte, slag and gas phases was evaluated, as a function of matte grade, amount of recirculated dust, oxygen enrichment and temperature. It was found that the concentration in the matte of the impurities such as arsenic, antimony and bismuth, increased slightly with recirculation of dust. On the other hand, the concentration of lead and zinc depend of the direct recirculation of dust to the process. Additionally, it was found that high concentrations of arsenic and antimony in the dust may lead to the formation and precipitation of copper arsenates and other metals (speiss), which may generates important operational problems. (Author) 15 refs.

  3. Water model experiments of multiphase mixing in the top-blown smelting process of copper concentrate

    Institute of Scientific and Technical Information of China (English)

    Hong-liang Zhao; Pan Yin; Li-feng Zhang; and Sen Wang

    2016-01-01

    We constructed a 1:10 cold water experimental model by geometrically scaling down an Isa smelting furnace. The mixing proc-esses at different liquid heights, lance diameters, lance submersion depths, and gas flow rates were subsequently measured using the conduc-tivity method. A new criterion was proposed to determine the mixing time. On this basis, the quasi-equations of the mixing time as a function of different parameters were established. The parameters of the top-blown smelting process were optimized using high-speed photography. An excessively high gas flow rate or excessively low liquid height would enhance the fluctuation and splashing of liquid in the bath, which is unfavorable for material mixing. Simultaneously increasing the lance diameter and the lance submersion depth would promote the mixing in the bath, thereby improving the smelting efficiency.

  4. Water model experiments of multiphase mixing in the top-blown smelting process of copper concentrate

    Science.gov (United States)

    Zhao, Hong-liang; Yin, Pan; Zhang, Li-feng; Wang, Sen

    2016-12-01

    We constructed a 1:10 cold water experimental model by geometrically scaling down an Isa smelting furnace. The mixing processes at different liquid heights, lance diameters, lance submersion depths, and gas flow rates were subsequently measured using the conductivity method. A new criterion was proposed to determine the mixing time. On this basis, the quasi-equations of the mixing time as a function of different parameters were established. The parameters of the top-blown smelting process were optimized using high-speed photography. An excessively high gas flow rate or excessively low liquid height would enhance the fluctuation and splashing of liquid in the bath, which is unfavorable for material mixing. Simultaneously increasing the lance diameter and the lance submersion depth would promote the mixing in the bath, thereby improving the smelting efficiency.

  5. Distribution and Behavior of Arsenic During the Reducing-Matting Smelting Process

    Science.gov (United States)

    Yang, Weichun; Tian, Shunqi; Wu, Jianxun; Chai, Liyuan; Liao, Qi

    2017-04-01

    The distribution and behavior of arsenic during the reducing-matting smelting process were investigated with various values of the carbon addition ratio, arsenic content, CaO/SiO2 ratio, and Fe/SiO2 ratio. The carbon addition ratio significantly affected the arsenic distribution among the phases, and most arsenic could be retained in an iron-rich matte with a carbon addition ratio greater than 20%. An increasing Fe/SiO2 ratio favored the retention and stabilization of arsenic in the iron-rich matte, and an increase in the CaO/SiO2 ratio decreased the arsenic volatilization and improved arsenic stability in the iron-rich matte and slag. It may be concluded from this study that the reducing-matting smelting process could be optimized by increasing the carbon addition ratio, CaO/SiO2 ratio, and Fe/SiO2 ratio and by decreasing the arsenic content.

  6. Flash ADC data processing with correlation coefficients

    Energy Technology Data Exchange (ETDEWEB)

    Blyth, D.; Gibson, M.; Mcfarland, D.; Comfort, J.R., E-mail: Joseph.Comfort@asu.edu

    2014-02-21

    The large growth of flash ADC techniques for processing signals, especially in applications of streaming data, raises issues such as data flow through an acquisition system, long-term storage, and greater complexity in data analysis. In addition, experiments that push the limits of sensitivity need to distinguish legitimate signals from noise. The use of correlation coefficients is examined to address these issues. They are found to be quite successful well into the noise region. The methods can also be extended to Field Programmable Gate Array modules for compressing the data flow and greatly enhancing the event rate capabilities.

  7. State of the direct reduction and reduction smelting processes

    Directory of Open Access Journals (Sweden)

    Markotić A.

    2002-01-01

    Full Text Available For quite a long time efforts have been made to develop processes for producing iron i.e. steel without employing conventional procedures - from ore, coke, blast furnace, iron, electric arc furnace, converter to steel. The insufficient availability and the high price of the coking coals have forced many countries to research and adopt the non-coke-consuming reduction and metal manufacturing processes (non-coke metallurgy, direct reduction, direct processes. This paper represents a survey of the most relevant processes from this domain by the end of 2000, which display a constant increase in the modern process metallurgy.

  8. Statistical modeling of copper losses in the silicate slag of the sulfide concentrate smelting process

    OpenAIRE

    2015-01-01

    This article presents the results of the statistical modeling of copper losses in the silicate slag of the sulfide concentrates smelting process. The aim of this study was to define the correlation dependence of the degree of copper losses in the silicate slag on the following parameters of technological processes: SiO2, FeO, Fe3O4, CaO and Al2O3 content in the slag and copper content in the matte. Multiple linear regression analysis (MLRA), artificial neural networks (ANNs) and adaptive netw...

  9. Influences of Technological Parameters on Smelting-separation Process for Metallized Pellets of Vanadium-bearing Titanomagnetite Concentrates

    Institute of Scientific and Technical Information of China (English)

    En-hui WU; Rong ZHU; Shao-li YANG; Lan MA; Jun LI; Jing HOU

    2016-01-01

    The smelting-separation process for metallized pellets of vanadium-bearing titanomagnetite concentrates was studied.The influences of smelting temperature,smelting time,and the basicity of the metallized pellet on vana-dium and iron recovery were investigated.The characteristics of titanium slag were analyzed using X-ray diffraction, energy dispersive spectroscopy,and mineralographic microscopic analysis.The results demonstrate that appropriate increases in smelting temperature and smelting time can improve the vanadium and iron recovery from metallized pel-lets and are beneficial for the slag-iron separation.Although increasing the basicity of the metallized pellet can consid-erably improve the vanadium and iron recovery,the TiO2 grade of titanium slag was decreased.Under the optimal conditions,90·17% of vanadium and 92·98% of iron in the metallized pellet were recovered,and the TiO2 grade of titanium slag was 55·01%.It was found that anosovite,augite,spinel,glassiness,and metallic iron were the main mineral phases of the titanium slag.

  10. Statistical modeling of copper losses in the silicate slag of the sulfide concentrate smelting process

    Directory of Open Access Journals (Sweden)

    Savic Marija V.

    2015-09-01

    Full Text Available This article presents the results of the statistical modeling of copper losses in the silicate slag of the sulfide concentrates smelting process. The aim of this study was to define the correlation dependence of the degree of copper losses in the silicate slag on the following parameters of technological processes: SiO2, FeO, Fe3O4, CaO and Al2O3 content in the slag and copper content in the matte. Multiple linear regression analysis (MLRA, artificial neural networks (ANNs and adaptive network based fuzzy inference system (ANFIS were used as tools for mathematical analysis of the indicated problem. The best correlation coefficient (R2 = 0.719 of the final model was obtained using the ANFIS modeling approach.

  11. Microprocessor based protecting and monitoring system for transformer of electric furnace in nickel smelting process

    Institute of Scientific and Technical Information of China (English)

    廖力清; 曾可; 凌玉华; 杨欣荣; 陈燕辉

    2001-01-01

    In nickel smelting process, the working conditions and surroundings for the transformer of electric furnace are worse than general electric power transformer. It is difficult to meet the requirements on reliability and safety by the conventional centralized control protection. With the development of microcomputer and field-bus technology, it is necessary to design a new type of protection and monitoring system for transformer of electric furnace. A microprocessor-based protection and monitoring system was described, which uses the embedded high performance microprocessor 87C196KC20 as its most important micro-controller unit & the technology of CAN (Controller Area Network) making it a fully distributed microcomputer system not only to perform all sorts of the transformer protection and function of automatic coinciding and communicate with the monitoring host, but also to carry with it the function of protecting, measuring, and fault diagnosis for transformer of electric furnace.

  12. Distributed query processing in flash-based sensor networks

    Institute of Scientific and Technical Information of China (English)

    Jianliang XU; Xueyan TANG; Wang-Chien LEE

    2008-01-01

    Wireless sensor networks are used in a large array of applications to capture,collect,and analyze physical environmental data.Many existing sensor systems instruct sensor nodes to report their measurements to central repositories outside the network,which is expensive in energy cost.Recent technological advances in flash memory have given rise to the development of storagecentric sensor networks,where sensor nodes are equipped with high-capacity flash memory storage such that sensor data can b.e stored and managed inside the network to reduce expensive communication.This novel architecture calls for new data management techniques to fully exploit distributed in-network data storage.This paper describes some of our research on distributed query processing in such flash-based sensor networks.Of particular interests are the issues that arise in the design of storage management and indexing structures combining sensor system workload and read/write/erase characteristics of flash memory.

  13. Optimization of suspension smelting technology by computer simulation

    Energy Technology Data Exchange (ETDEWEB)

    Lilius, K.; Jokilaakso, A.; Ahokainen, T.; Teppo, O.; Yang Yongxiang [Helsinki Univ. of Technology, Otaniemi (Finland). Lab. of Materials Processing and Powder Metallurgy

    1994-12-31

    The flash smelting process has been extensively studied during its over 40 years existence. Laboratory or pilot scale experiments can not, however, predict all the complicated and coupled phenomena taking place in a flash smelting furnace. Development of commercial modelling software and increasingly efficient computers have brought a new tool to researchers for more comprehensive investigation of the transport and combustion processes taking place in the flash smelting process. A flash smelting furnace and a waste-heat boiler geometry have been simulated in two- and three-dimensional laboratory models which have, in turn, been modeled by using commercial Computational-Fluid-Dynamics -software. The computer simulation has then been extended to an industrial-scale furnace and waste-heat boiler. The work has proceeded from cold gas flow to heat transfer, combustion, and two-phase flow simulations. In the present approach, the modelling task has been divided into submodels. Outlet values of a model are used as inlet values in the subsequent submodel. Heat transfer calculations have been carried out starting from very basic considerations. Different options of the software and heat transfer modes have been tested, and hot gas flow through the furnace and boiler has been simulated. Validation of the models was carried out with temperature measurements from the uptake shaft. Also one geometrical variation of the uptake shaft has been simulated, namely turning the outlet of the shaft 90 degrees. Combustion of sulphides is approximated with gaseous combustion by using a built-in combustion model of the software. The waste-heat boiler has been simulated first as an empty geometry, and adding gradually approximated radiation curtains and convection tube bundles. Both convection and radiation heat transfer were considered. (orig.)

  14. Comparison the Physico-Chemical Model of Ferrosilicon Smelting Process with Results Observations of the Process under the Industrial Conditions

    Directory of Open Access Journals (Sweden)

    Machulec B.

    2016-03-01

    Full Text Available Based on the minimum Gibbs Free Enthalpy algorithm (FEM, model of the ferrosilicon smelting process has been presented. It is a system of two closed isothermal reactors: an upper one with a lower temperature T1, and a lower one with a higher temperature T2. Between the reactors and the environment as well as between the reactors inside the system, a periodical exchange of mass occurs at the moments when the equilibrium state is reached. The condensed products of chemical reactions move from the top to the bottom, and the gas phase components move in the opposite direction. It can be assumed that in the model, the Reactor 1 corresponds to the charge zone of submerged arc furnace where heat is released as a result of resistive heating, and the Reactor 2 corresponds to the zones of the furnace where heat is produced by electric arc. Using the model, a series of calculations was performed for the Fe-Si-O-C system and was determined the influence of temperatures T1, T2 on the process. The calculation results show a good agreement model with the real ferrosilicon process. It allows for the determination of the effects of temperature conditions in charge zones and arc zones of the ferrosilicon furnace on the carbothermic silica reduction process. This allows for an explanation of many characteristic states in the ferrosilicon smelting process.

  15. Optimization of suspension smelting technology by computer simulation

    Energy Technology Data Exchange (ETDEWEB)

    Lilius, K.; Jokilaakso, A.; Ahokainen, T.; Teppo, O.; Yang Yongxiang [Helsinki Univ. of Technology, Otaniemi (Finland). Lab. of Materials Processing and Powder Metallurgy

    1996-12-31

    An industrial-scale flash smelting furnace and waste-heat boilers have been modelled by using commercial Computational-Fluid-Dynamics software. The work has proceeded from cold gas flow to heat transfer, combustion, and two-phase flow simulations. In the present study, the modelling task has been divided into three sub-models: (1) the concentrate burner, (2) the flash smelting furnace (reaction shaft and uptake shaft), and (3) the waste-heat boiler. For the concentrate burner, the flow of the process gas and distribution air together with the concentrate or a feed mixture was simulated. Eulerian - Eulerian approach was used for the carrier gas-phase and the dispersed particle-phase. A large parametric study was carried out by simulating a laboratory scale burner with varying turbulence intensities and then extending the simulations to the industrial scale model. For the flash smelting furnace, the simulation work concentrated on gas and gas-particle two-phase flows, as well as the development of combustion model for sulphide concentrate particles. Both Eulerian and Lagrangian approaches have been utilised in describing the particle phase and the spreading of the concentrate in the reaction shaft as well as the particle tracks have been obtained. Combustion of sulphides was first approximated with gaseous combustion by using a built-in combustion model of the software. The real oxidation reactions of the concentrate particles were then coded as a user-defined sub-routine and that was tested with industrial flash smelting cases. For the waste-heat boiler, both flow and heat transfer calculations have been carried out for an old boiler and a modified boiler SULA 2 Research Programme; 23 refs.

  16. Smelting reduction process with a thick layer of slag for producing ferroalloys and iron

    Energy Technology Data Exchange (ETDEWEB)

    Katayama, H. (Nippon Steel Corp., Tokyo (Japan))

    1992-06-01

    Smelting reduction process with a thick layer of slag is one of the potential technologies of a flexible manufacturing system desired for the production iron and steel. Its feature is that an oxygen jet is separated from the molten metal by a thick layer of slag, and it is realized by the coexistence of carbonaceous material for controlling slag foaming and allows high post combustion operation without disturbing the reducing reaction. Experimental furnaces of 100kg, 600kg, 3t and 100t were built for the production Cr-Fe-C, Mn-Fe-C and Fe-C and the experimental production was performed successfully. The procedure of the experiments is reviewed and slag foaming and its control, the properties of the slag layer, the reducing reaction, direct supply of fine ore, the mechanism of heat transfer, post combustion and coal consumption are discussed. Though there are some problems in the decrease of post combustion in the use of coal with high volatile content, this process has no problem in enlargement of the scale, and it is promising for the flexible production of iron. It also can be applied for scrap melting. 67 refs., 15 figs., 3 tabs.

  17. Dynamic Optimization of UV Flash Processes

    DEFF Research Database (Denmark)

    Ritschel, Tobias Kasper Skovborg; Capolei, Andrea; Jørgensen, John Bagterp

    2017-01-01

    UV ash processes, also referred to as isoenergetic-isochoric ash processes, occur for dynamic simulation and optimization of vapor-liquid equilibrium processes. Dynamic optimization and nonlinear model predictive control of distillation columns, certain two-phase ow problems, as well as oil reser...... that the optimization solver, the compiler, and high-performance linear algebra software are all important for e_cient dynamic optimization of UV ash processes....

  18. Wastes from the coal-enrichment process as alternative reducers for lead smelting from lead-acid accmulator scrap

    Directory of Open Access Journals (Sweden)

    J. Lipart

    2013-10-01

    Full Text Available In the paper, results of the study on a possible utilization of coal-enrichment wastes as alternative reducers for lead smelting from acid-lead accumulator scrap are presented. For the experiments, the following alternative carboniferous reducers were selected: coal slurry, anthracite dust and coal soot. The investigations included both laboratoryscale experiments and semi-industrial tests in a rotary furnace. The findings allowed for a review of the effects of a sample type (loose material or material post a preliminary agglomeration process, loaded into the furnace, on a final process yield.

  19. Interaction mechanism between refractory and melts in iron bath smelting reduction process

    Directory of Open Access Journals (Sweden)

    Qiu G.B.

    2010-01-01

    Full Text Available The corrosion behavior of three sorts of refractories based on alumina-graphite were studied by immersion tests. The melts included smelting reduction molten slag and corresponding carbon saturated molten iron. The influence of test temperature, FeO content in slag and specimen rotative velocity on the corrosion rate of refractories was examined. By means of SEM and EDS, the microstructure change of the refractories after immersion test in kinds of melts was studied. The morphology of the deteriorated layer showed the corrosion extent of refractories. With the addition of zirconia and titania into the refractories, the corrosion rate changed to some extent. The corrosion rate of three sorts of refractories increased dramatically with the increasing FeO content in smelting reduction slag. Compared with alumina-graphite refractory and alumina-graphite-zirconia refractory, alumina-graphite-titania refractory had stronger corrosion resistance in the smelting reduction conditions. By the results of SEM and EDS, the corrosion mechanism of refractories was developed.

  20. Flash Cracking Reactor for Waste Plastic Processing

    Science.gov (United States)

    Timko, Michael T.; Wong, Hsi-Wu; Gonzalez, Lino A.; Broadbelt, Linda; Raviknishan, Vinu

    2013-01-01

    Conversion of waste plastic to energy is a growing problem that is especially acute in space exploration applications. Moreover, utilization of heavy hydrocarbon resources (wastes, waxes, etc.) as fuels and chemicals will be a growing need in the future. Existing technologies require a trade-off between product selectivity and feedstock conversion. The objective of this work was to maintain high plastic-to-fuel conversion without sacrificing the liquid yield. The developed technology accomplishes this goal with a combined understanding of thermodynamics, reaction rates, and mass transport to achieve high feed conversion without sacrificing product selectivity. The innovation requires a reaction vessel, hydrocarbon feed, gas feed, and pressure and temperature control equipment. Depending on the feedstock and desired product distribution, catalyst can be added. The reactor is heated to the desired tempera ture, pressurized to the desired pressure, and subject to a sweep flow at the optimized superficial velocity. Software developed under this project can be used to determine optimal values for these parameters. Product is vaporized, transferred to a receiver, and cooled to a liquid - a form suitable for long-term storage as a fuel or chemical. An important NASA application is the use of solar energy to convert waste plastic into a form that can be utilized during periods of low solar energy flux. Unlike previous work in this field, this innovation uses thermodynamic, mass transport, and reaction parameters to tune product distribution of pyrolysis cracking. Previous work in this field has used some of these variables, but never all in conjunction for process optimization. This method is useful for municipal waste incinerator operators and gas-to-liquids companies.

  1. Life cycle inventory analysis of CO2 and SO2 emission of imperial smelting process for Pb-Zn smelter

    Institute of Scientific and Technical Information of China (English)

    李启厚; 郭学益; 肖松文; 黄凯; 张多默

    2003-01-01

    Based on the principle of life cycle assessment, CO2 and SO2 emission of Imperial Smelting Process in a certain zinc-lead smelter was analyzed by life cycle inventory method. According to the system expansion and substitution method, the environmental impacts of co-products were allocated among the main products of zinc, lead and sulfuric acid. The related impacts were assessed by use of Global Warming Potential (GWP) and Acidification Potential (ACP). The results show that the GWP index from 1998 to 2000 is 11.53, 11.65, 10.93 tCO2-eq/tZn respectively, the ACP index decreases from 14.88 kgSO2-eq/tZn in 1998 to 10.99 kgSO2-eq/tZn in 2000. Power and electricity generation, followed by smelting and zinc distillation, are mainly responsible for GWP. Sintering individually affects ACP. Reduction in greenhouse gas emissions of the ISP may come from energy conservation measures rather than from technological developments. And recycling more secondary Pb and Zn materials effectively treated by ISP, and reducing the amount of primary metal are the main ways to put SO2 emission under control.

  2. Energy Consumption in Copper Smelting: A New Asian Horse in the Race

    Science.gov (United States)

    Coursol, P.; Mackey, P. J.; Kapusta, J. P. T.; Valencia, N. Cardona

    2015-05-01

    After a marked improvement in energy consumption in copper smelting during the past few decades, technology development has been slowing down in the Americas and in Europe. Innovation, however, is still required to further reduce energy consumption while complying with stringent environmental regulations. The bottom blowing smelting technology being developed in China shows success and promise. The general configuration of the bath smelting vessel, the design of high-pressure injectors, and the concentrate addition system are described and discussed in this article with respect to those used in other technologies. The bottom blowing technology is shown to be operating at a temperature in the range of 1160-1180°C, which is the lowest reported temperature range for a modern copper smelting process. In this article, it is suggested that top feeding of filter cake concentrate, which is also used in other technologies, has a positive effect in reducing the oxidation potential of the slag ( p(O2)) while increasing the FeS solubility in slag. This reduction in p(O2) lowers the magnetite liquidus of the slag, while the increased solubility of FeS in slag helps toward reaching very low copper levels in flotation slag tailings. The application of high-pressure injectors allows for the use of high levels of oxygen enrichment with no requirements for punching. Using a standard modeling approach from the authors' previous studies, this article discusses these aspects and compares the energy consumption of the bottom blowing technology with that of other leading flash and bath smelting technologies, namely: flash smelting, Noranda/Teniente Converter, TSL (Isasmelt [Glencore Technology Pty. Ltd., Brisbane, Queensland, Australia]/Outotec), and the Mitsubishi Process (Mitsubishi Materials Corporation, Tokyo, Japan).

  3. Audition influences color processing in the sound-induced visual flash illusion.

    Science.gov (United States)

    Mishra, Jyoti; Martinez, Antigona; Hillyard, Steven A

    2013-12-18

    Multisensory interactions can lead to illusory percepts, as exemplified by the sound-induced extra flash illusion (SIFI: Shams, Kamitani, & Shimojo, 2000, 2002). In this illusion, an audio-visual stimulus sequence consisting of two pulsed sounds and a light flash presented within a 100 ms time window generates the visual percept of two flashes. Here, we used colored visual stimuli to investigate whether concurrent auditory stimuli can affect the perceived features of the illusory flash. Zero, one or two pulsed sounds were presented concurrently with either a red or green flash or with two flashes of different colors (red followed by green) in rapid sequence. By querying both the number and color of the participants' visual percepts, we found that the double flash illusion is stimulus specific: i.e., two sounds paired with one red or one green flash generated the percept of two red or two green flashes, respectively. This implies that the illusory second flash is induced at a level of visual processing after perceived color has been encoded. In addition, we found that the presence of two sounds influenced the integration of color information from two successive flashes. In the absence of any sounds, a red and a green flash presented in rapid succession fused to form a single orange percept, but when accompanied by two sounds, this integrated orange percept was perceived to flash twice on a significant proportion of trials. In addition, the number of concurrent auditory stimuli modified the degree to which the successive flashes were integrated to an orange percept vs. maintained as separate red-green percepts. Overall, these findings show that concurrent auditory input can affect both the temporal and featural properties of visual percepts. Copyright © 2013 Elsevier Ltd. All rights reserved.

  4. Feasibility of lead extraction from waste Cathode-Ray-Tubes (CRT) funnel glass through a lead smelting process.

    Science.gov (United States)

    Lv, Jianfang; Yang, Hongying; Jin, Zhenan; Ma, Zhiyuan; Song, Yan

    2016-11-01

    A novel and effective process for extracting lead from the hazardous waste Cathode Ray Tubes (CRT) funnel glass is presented. The technological breakthrough of this process is introducing the discarded CRT funnel glass to traditional lead smelting. In this study, the influences of amount of carbon addition, calcium-silicate ratio, temperature, holding time and funnel glass addition on lead extraction efficiency were investigated to determine the optimal operational parameters. With a glass addition of less than 30wt%, a high extraction yield of 97.5% of lead from the mixture of funnel glass and lead slag was successfully obtained by controlling the C/PbO molar ratio, CaO/SiO2 ratio, temperature, treatment time at 0.9, 0.8, 1200°C, 60min, respectively. The main crystalline phases of the residues were calcium silicate slag, and an amorphous glass phase appears at a glass addition more than 30wt%. Thermodynamic calculation shows that the proportion of liquid phase in the slag first increased and then decreased, when the addition of glass is increased, while the viscosity of the slag exhibited a continuous decrease. Thus, based on all the results, it is concluded that the process proposed in this paper is an effective and promising approach for reutilization of obsolete CRT funnel glass. Copyright © 2016 Elsevier Ltd. All rights reserved.

  5. Research and Industrial Application of a Process for Direct Reduction of Molten High-Lead Smelting Slag

    Science.gov (United States)

    Li, Weifeng; Zhan, Jing; Fan, Yanqing; Wei, Chang; Zhang, Chuanfu; Hwang, Jiann-Yang

    2017-01-01

    A pyrometallurgical process for the direct reduction of molten high-lead smelting slag obtained by the Shuikoushan (SKS) method was reported in this article using solid anthracite as the fuel and reductant. The chemical composition, the lead phase composition, and the physical properties of the molten high-lead slag were examined. The effects of the process parameters on the recovery rate of valued metals were investigated in the laboratory. According to the experimental results, a new efficient bottom blow reduction furnace was employed in the pilot-scale test for high-lead slag reduction. The results showed the average recovery rate of lead was more than 96.0% with lower Pb and high Zn content of the reducing slag under the condition of reduction temperature 1100-1200°C, coal ratio 5.5-7.5%, reduction time 90-150 min, CaO/SiO2 ratio 0.35-0.45, and FeO/SiO2 ratio 1.4-1.55. Moreover, nearly 250 kg of standard coal per ton of crude Pb output was reduced compared with the blast furnace reduction process.

  6. Flash Cracking Reactor for Waste Plastic Processing Project

    Data.gov (United States)

    National Aeronautics and Space Administration — We propose to design, model, build, and test a novel flash cracking reactor to convert plastic waste, and potentially other unconventional hydrocarbon feedstocks,...

  7. 3D Flash LIDAR Real-Time Embedded Processing Project

    Data.gov (United States)

    National Aeronautics and Space Administration — 3D Flash LIDAR (3DFL) is ideal for determining real-time spacecraft trajectory, speed and orientation to the planet surface, as well as evaluating potential hazards...

  8. 3D Flash LIDAR Real-Time Embedded Processing Project

    Data.gov (United States)

    National Aeronautics and Space Administration — Advanced Scientific Concepts, Inc. (ASC) is a small business, which has developed a compact, eye-safe 3D Flash LIDARTM Camera (FLC) well suited for real-time...

  9. Recovery of iron and calcium aluminate slag from high-ferrous bauxite by high-temperature reduction and smelting process

    Institute of Scientific and Technical Information of China (English)

    Ying-yi Zhang; Wei L; Yuan-hong Qi; Zong-shu Zou

    2016-01-01

    A high-temperature reduction and smelting process was used to recover iron and calcium aluminate slag from high-ferrous bauxite. The effects of w(CaO)/w(SiO2) ratio, anthracite ratio, and reduction temperature and time on the recovery and size of iron nuggets and on the Al2O3 grade of the calcium aluminate slag were investigated through thermodynamic calculations and experiments. The optimized process conditions were the bauxite/anthracite/slaked lime weight ratio of 100:16.17:59.37, reduction temperature of 1450°C and reduction time of 20 min. Under these conditions, high-quality iron nuggets and calcium aluminate slag were obtained. The largest size and the highest recov-ery rate of iron nuggets were 11.42 mm and 92.79wt%, respectively. The calcium aluminate slag mainly comprised Ca2SiO4 and Ca12Al14O33, with small amounts of FeAl2O4, CaAl2O4, and Ca2Al2SiO7.

  10. A study on reduction of copper slag from the flash furnace with the use of anthracite dust

    Directory of Open Access Journals (Sweden)

    G. Siwiec

    2014-07-01

    Full Text Available In the paper, results of a study on reduction of blister copper flash smelting slag with the use of anthracite dust are presented. The material, following proper preparation, can be used for slag processing as a substitute for currently applied coke breeze.

  11. 高氟铍矿石熔炼过程中脱氟研究%Study on Defluorination of High Fluorine Bearing Beryllium Ore in Smelting Process

    Institute of Scientific and Technical Information of China (English)

    雷湘

    2013-01-01

    高氟铍矿石在熔炼过程中配入氢氧化铝来脱除其中的氟.结果表明,在配入5%Na2CO3、9.3%Al(OH)3、1400~1500℃熔炼20 min的情况下,BeO回收率达到96%以上,脱氟效果良好(铍玻璃F/BeO能控制在15%以内).为高氟铍矿石的工业应用探索出新的冶炼途径.%Defluorination with addition of aluminum hydroxide in smelting process of high fluorine bearing beryllium ore was investigated. The results show that BeO recovery is above 96% under the conditions including dosage of Na2CO3 of 5%, dosage of A1(OH)3 of 9.3%, smelting temperature of 1 400~1 500℃, and time of 20 min. Defluorination effect is fine in that the ratio of F/BeO of beryllium glass could be controlled below 15%. This new smelting process facilitates the industrial application of high fluorine bearing beryllium ore.

  12. Numerical Modeling of Flow Dynamics in The Aluminum Smelting Process: Comparison Between Air-Water and CO2-Cryolite Systems

    Science.gov (United States)

    Zhao, Zhibin; Feng, Yuqing; Schwarz, M. Philip; Witt, Peter J.; Wang, Zhaowen; Cooksey, Mark

    2017-04-01

    Air-water models have been widely applied as substitutes for CO2-cryolite systems in the study of the complex bubble dynamics and bubble-driven flow that occurs in the molten electrolyte phase in the aluminum electrolytic process, but the detailed difference between the two systems has not been studied. This paper makes a numerical comparison between the bubble dynamics for the two systems. Simulations of both single bubble and continuous bubbling were conducted using a three-dimensional computational fluid dynamics (3D CFD) modeling approach with a volume of fluid (VOF) method to capture the phase interfaces. In the single bubble simulations, it was found that bubbles sliding under an anode in a CO2-cryolite system have a smaller bubble thickness and a higher sliding velocity than those in the air-water system for bubbles of the same volume. Dimensionless analysis and numerical simulation show that contact angle is the dominant factor producing these differences; the effects of kinematic viscosity, surface tension, and density are very small. In the continuous bubbling simulations, the continuous stream of air bubbles detaches from the anode sidewall after a period of climbing, just as it does in the single bubble simulation, but bubbles have less tendency to migrate away from the wall. Quasi-stable state flow characteristics, i.e., time-averaged bath flow pattern, turbulence kinetic energy, turbulence dissipation rate, and gas volume fraction, show a remarkable agreement between the two systems in terms of distribution and magnitude. From the current numerical comparisons, it is believed that the air-water model is a close substitutive model for studying bubble-driven bath flow in aluminum smelting processes. However, because of the difference in bubble morphologies between the two systems, and also the reactive generation and growth of bubbles in the real system, there will likely be some differences in bubble coverage of the anode in the anode-cathode gap.

  13. Numerical Modeling of Flow Dynamics in The Aluminum Smelting Process: Comparison Between Air-Water and CO2-Cryolite Systems

    Science.gov (United States)

    Zhao, Zhibin; Feng, Yuqing; Schwarz, M. Philip; Witt, Peter J.; Wang, Zhaowen; Cooksey, Mark

    2016-12-01

    Air-water models have been widely applied as substitutes for CO2-cryolite systems in the study of the complex bubble dynamics and bubble-driven flow that occurs in the molten electrolyte phase in the aluminum electrolytic process, but the detailed difference between the two systems has not been studied. This paper makes a numerical comparison between the bubble dynamics for the two systems. Simulations of both single bubble and continuous bubbling were conducted using a three-dimensional computational fluid dynamics (3D CFD) modeling approach with a volume of fluid (VOF) method to capture the phase interfaces. In the single bubble simulations, it was found that bubbles sliding under an anode in a CO2-cryolite system have a smaller bubble thickness and a higher sliding velocity than those in the air-water system for bubbles of the same volume. Dimensionless analysis and numerical simulation show that contact angle is the dominant factor producing these differences; the effects of kinematic viscosity, surface tension, and density are very small. In the continuous bubbling simulations, the continuous stream of air bubbles detaches from the anode sidewall after a period of climbing, just as it does in the single bubble simulation, but bubbles have less tendency to migrate away from the wall. Quasi-stable state flow characteristics, i.e., time-averaged bath flow pattern, turbulence kinetic energy, turbulence dissipation rate, and gas volume fraction, show a remarkable agreement between the two systems in terms of distribution and magnitude. From the current numerical comparisons, it is believed that the air-water model is a close substitutive model for studying bubble-driven bath flow in aluminum smelting processes. However, because of the difference in bubble morphologies between the two systems, and also the reactive generation and growth of bubbles in the real system, there will likely be some differences in bubble coverage of the anode in the anode-cathode gap.

  14. Experimental Investigation and Modeling of Copper Smelting Slags

    Science.gov (United States)

    Starodub, Konstantin; Kuminova, Yaroslava; Dinsdale, Alan; Cheverikin, Vladimir; Filichkina, Vera; Saynazarov, Abdukahhar; Khvan, Alexandra; Kondratiev, Alex

    2016-10-01

    Effective extraction of copper from sulfide ores requires careful operation of a copper smelter, which in turn depends very much on chemistry of the feed and resulted slag and matte. For example, chemical composition of copper smelting slags has to be in a certain range to ensure that their properties are within specific limits. Disobeying these rules may lead to complications in smelting operation, poor quality of the copper products, and premature shutdown of the copper smelter. In the present paper the microstructure and phase composition of slags from the Almalyk copper flash smelter were investigated experimentally and then modeled thermodynamically to evaluate potential ways of improvement and optimization of the copper smelting process and its products. The slag samples were taken at different stages of the copper smelting process: on slag tapping, after slag transportation to a deposition site, and at the site. Experimental investigation included the XRD, XRF, and SEM techniques, which were also confirmed by the traditional wet chemistry analysis. Thermodynamic modeling was carried out using thermochemical software package MTDATA, which enables thermodynamic and physical properties of the matte, slag, and gas phases to be calculated in a wide range of temperatures, pressures, and chemical compositions. In addition, slag viscosities and corresponding matte settling rates were estimated using the modified Urbain and Utigard-Warczok models, and the Hadamard-Rybczynski equation, respectively. It was found that the copper content in the slags may vary significantly depending on the location of slag sampling. Cu was found to be present as sulfide particles, almost no Cu was found to be dissolved in the slag. Analysis of microstructure and phase composition showed that major phase found in the samples is fayalite, while other phases are complex spinels (based on magnetite), different sulfides, and a glass-like phase. Thermodynamic calculations demonstrated the

  15. The sulfide ore looping oxidation process: An alternative to current roasting and smelting practice

    Science.gov (United States)

    McHugh, Larry F.; Balliett, Robert; Mozolic, Jean A.

    2008-07-01

    This novel method utilizes the reactions of metal sulfides and metal oxides. It is applicable to single-metal systems such as Mo, Cu, Co, Ni, Fe, and Zn individual sulfides and to mixed sulfides such as chalcopyrite and Mo/Fe. In addition to primary ores, waste stream products such as spent catalysts can be effectively processed. The benchmark work done on MoS2/MoO3 resulted in an MoO2 product with less than 0.095 wt.% sulfur. Other sulfide concentrate materials showed similar results. In the first stage of the looping process, a highly concentrated SO2 off-gas stream is produced that could be directed to an acid plant or converted to liquid. The products from the first process step can be directed down line for further processing or can be used as is. In the second step of looping oxidation, the product is oxidized back to its fully oxidized state and is mainly looped back to drive the oxidation process in the first reaction. There are also several opportunities for energy recovery and conversion, making looping oxidation an energy-efficient process.

  16. How to avoid the `invisible gorilla' in aluminum smelting process control: Visual guidelines

    Science.gov (United States)

    Gao, Yashuang; Taylor, Mark P.; Chen, John J. J.; Hautus, Michael J.

    2011-08-01

    Over the last three decades, process control in aluminum smelters has improved significantly as it is the biggest leverage for cost and energy reduction in production and product quality improvement, as well as for meeting environmental compliance. The implementation of computerized automatic control systems two decades ago was a step change in improvement in the state of the art of process control. However, the complex and dynamic nature of the process requires human monitoring, diagnosis, and intervention from time to time. This study investigates the use of the supervisory screen of the control system of a smelter, as well as the effectiveness of visual guidelines to help the operators to identify process abnormalities. The results show that visual guidelines such as voltage patterns which are used as a reference improve the performance of the operators. Detection time and falsealarm rates were reduced in addition to increasing detection sensitivities. It is proposed that a higher level of human and system interaction would improve the overall performance process control.

  17. Evaluating Non-In-Place Update Techniques for Flash-Based Transaction Processing Systems

    Science.gov (United States)

    Wang, Yongkun; Goda, Kazuo; Kitsuregawa, Masaru

    Recently, flash memory is emerging as the storage device. With price sliding fast, the cost per capacity is approaching to that of SATA disk drives. So far flash memory has been widely deployed in consumer electronics even partly in mobile computing environments. For enterprise systems, the deployment has been studied by many researchers and developers. In terms of the access performance characteristics, flash memory is quite different from disk drives. Without the mechanical components, flash memory has very high random read performance, whereas it has a limited random write performance because of the erase-before-write design. The random write performance of flash memory is comparable with or even worse than that of disk drives. Due to such a performance asymmetry, naive deployment to enterprise systems may not exploit the potential performance of flash memory at full blast. This paper studies the effectiveness of using non-in-place-update (NIPU) techniques through the IO path of flash-based transaction processing systems. Our deliberate experiments using both open-source DBMS and commercial DBMS validated the potential benefits; x3.0 to x6.6 performance improvement was confirmed by incorporating non-in-place-update techniques into file system without any modification of applications or storage devices.

  18. Processing Trade Tariff Reductions Lead to a Decline in Copper Smelting Enterprises’ Export Cost

    Institute of Scientific and Technical Information of China (English)

    2012-01-01

    <正>The Notice of the Ministry of Finance and the State Administration of Taxation on Labor VAT and Consumption Tax Policy on Export Goods(Cai Shui 〔 2012 〕 39) was released. Three percent consolidated tax on copper concentrate processing export trade under the proc-

  19. Mineral Processing Experiment on Copper Smelting Slag%某铜冶炼渣铜选矿试验研究

    Institute of Scientific and Technical Information of China (English)

    陈杜娟; 李福兰

    2016-01-01

    针对甘肃某公司所属的铜冶炼渣成分复杂、嵌布粒度不均匀的性质特点采用优先快速浮选出一部分易浮铜矿物得到合格的铜精矿1,优先浮选尾矿经一次粗选、三次精选、一次扫选获得合格的铜精矿2,一次精选中矿及扫选中矿返回球磨机再磨的工艺流程,铜粗选二采用针对该铜冶炼渣性质研制的新型捕收起泡剂酯-11,闭路试验获得了铜品位为29.69%,铜回收率为85.62%的总铜精矿,试验指标良好,为现场工艺改进提供了技术依据。%In view of the characteristic of composition complex, uneven disseminated extent of copper smelting slag in a Gansu enterprise, the following flowsheet was adopted:a part of copper content of easy floatation was floated with rapid se⁃lective⁃flotation to acquire copper concentrate 1, then the qualified copper concentrate. 2 was acquired by once roughing, triple refined concentration and once scavenging from the preferential flotation tailings, the middings of once concentrating and scavenging was returned to ball mill. The new collecting foaming agent ester⁃11 which was developed aiming at the char⁃acteristic of this slag was adopted in the second copper roughing. Closed⁃circuit test obtained the total copper content with copper grade 29.69%, copper recovery 85.62%, the indexes was well, which provides technical basis for process improve⁃ment.

  20. Effects of Basicity and MgO in Slag on the Behaviors of Smelting Vanadium Titanomagnetite in the Direct Reduction-Electric Furnace Process

    Directory of Open Access Journals (Sweden)

    Tao Jiang

    2016-05-01

    Full Text Available The effects of basicity and MgO content on reduction behavior and separation of iron and slag during smelting vanadium titanomagnetite by electric furnace were investigated. The reduction behaviors affect the separation of iron and slag in the direct reduction-electric furnace process. The recovery rates of Fe, V, and Ti grades in iron were analyzed to determine the effects of basicity and MgO content on the reduction of iron oxides, vanadium oxides, and titanium oxides. The chemical compositions of vanadium-bearing iron and main phases of titanium slag were detected by XRF and XRD, respectively. The results show that the higher level of basicity is beneficial to the reduction ofiron oxides and vanadium oxides, and titanium content dropped in molten iron with the increasing basicity. As the content of MgO increased, the recovery rate of Fe increased slightly but the recovery rate of V increased considerably. The grades of Ti in molten iron were at a low level without significant change when MgO content was below 11%, but increased as MgO content increased to 12.75%. The optimum conditions for smelting vanadium titanomagnetite were about 11.38% content of MgO and quaternary basicity was about 1.10. The product, vanadium-bearing iron, can be applied in the converter steelmaking process, and titanium slag containing 50.34% TiO2 can be used by the acid leaching method.

  1. A novel method to alleviate flash-line defects in coining process

    KAUST Repository

    Xu, Jiangping

    2013-04-01

    We employ a finite element framework based on a dynamic explicit algorithm to predict the flash-line defects in the coining process. The distribution of the flash-line is obtained by building a radial friction work model at the element level. The elasto-plastic behavior of porous materials undergoing large deformations is considered where the constitutive level updates are the result of a local variational minimization problem. We study the material flow at different strokes of the die across the entire coining process and observe that the change in the flow direction of the material in the rim region may contribute to the flash lines. Our proposed framework shows that a part of the rim region in which the flash-line defects appear is consistent with the reported experimental results. We also propose a novel method of redesigning the rim geometry of the workpiece to alleviate the flash-line defects which also shows good agreement with experiments. © 2012 Elsevier Inc. All rights reserved.

  2. Standardization of the process of smelting for sands with self-forgeling resins in the Military Industry Santa Bárbara Factory

    Directory of Open Access Journals (Sweden)

    Lina Consuelo Carvajal-Fernández

    2014-12-01

    Full Text Available This article describes the standardization of the smelting process for sands with self-forgeling resins in the Military Industry Santa Barbara Factory. The molding process was studied in the Smelter for six months, to set standards for workforce and raw materials, so that would allow truthfully evaluate the costs per kilogram of casting. 41 pieces of civil and military sectors throughout the development of the project were worked. Finally both standards were evaluated, labor as raw material for different parts, with results was evidenced improved process, essentially in workforce, while in raw material standards did not show significantly change, in this case is corroborated that existing ones are applicable to the process

  3. 铜冶炼污酸污水处理工艺流程的优化%Process Optimization of Waste Acid and Wastewater in Copper Smelting

    Institute of Scientific and Technical Information of China (English)

    徐焰

    2013-01-01

    The processes to treat waste acid and wastewater in blister copper smelting were optimized.The processes to harmlessly discharge high arsenic-bearing waste acid and wastewater and to neutralize slag were put forward.The high arsenic-bearing waste acid and wastewater can be harmlessly discharged after process optimization.%对粗铜冶炼中污酸、污水处理工艺流程进行优化,提出了高砷污酸、污水达标排放的处理工艺以及中和渣无害化的方法.流程优化后高含砷污酸污水可以达标排放.

  4. Two-step flash light sintering process for crack-free inkjet-printed Ag films

    Science.gov (United States)

    Park, Sung-Hyeon; Jang, Shin; Lee, Dong-Jun; Oh, Jehoon; Kim, Hak-Sung

    2013-01-01

    In this paper, a two-step flash light sintering process for inkjet-printed Ag films is investigated with the aim of improving the quality of sintered Ag films. The flash light sintering process is divided into two steps: a preheating step and a main sintering step. The preheating step is used to remove the organic binder without abrupt vaporization. The main sintering step is used to complete the necking connections among the silver nanoparticles and achieve high electrical conductivity. The process minimizes the damage on the polymer substrate and the interface between the sintered Ag film and polymer substrate. The electrical conductivity is calculated by measuring the resistance and cross-sectional area with an LCR meter and 3D optical profiler, respectively. It is found that the resistivity of the optimal flash light-sintered Ag films (36.32 nΩ m), which is 228.86% of that of bulk silver, is lower than that of thermally sintered ones (40.84 nΩ m). Additionally, the polyimide film used as the substrate is preserved with the inkjet-printed pattern shape during the flash light sintering process without delamination or defects.

  5. Smelting Oxidation Desulfurization of Copper Slags

    Institute of Scientific and Technical Information of China (English)

    LI Lei; HU Jian-hang; WANG Hua

    2012-01-01

    According to the mechanism of sulfur removal easily through oxidation, the process of smelting oxidation desulfurization of copper slags is studied, which supplies a new thinking for obtaining the molten iron of lower sulfur content by smelting reduction of copper slags. Special attention is given to the effects of the holding temperature, the holding time and CaF2, CaO addition amounts on the desulfurization rate of copper slags. The results indicate that the rate of copper slags smelting oxidation desulfurization depends on the matte mass transfer rate through the slag phase. After the oxidation treatment, sulfur of copper slags can be removed as SO2 efficiently. Amount of Ca2+ of copper slags affects the desulfurization rate greatly, and the slag desulfurization rate is reduced by adding a certain amount of CaF2 and CaO. Compared with CaF2, CaO is negative to slags sulfur removal with equal Ca2+ addition. Under the air flow of 0.3 U/min, the sulfur content of copper slags can be reduced to 0. 004 67% in the condition of the holding time of 3 min and the holding temperature of 1 500 ℃. The sulfur content of molten iron is reduced to 0. 000 8 % in the smelting reduction of treated slags, and the problem of high sulfur content of molten iron obtained by smelting reduction with copper slag has been successively solved.

  6. Smelting Process of SA-508-3-1 Steel for Nuclear Plant Reactor Pressure Vessel%核电压力容器用 SA-508-3-1钢的冶炼

    Institute of Scientific and Technical Information of China (English)

    薛永栋; 晋帅勇; 汪勇; 郭彪

    2012-01-01

      The SA-508-3-1 ingot steel smelting process of EBT smelting-LF refining-VD-VC has been put forward by analyzing the difficulties of smelting process based on the characteristics of steel structure and property requirement for nuclear plant reactor pressure vessel .The nuclear power SA-508-3-1 ingot steel has been produced successfully ac-cording to this steel smelting process .The property of the forgings has reached the requirement of NRPV forgings after forging and heat treatment processes which helped CITIC HEAVY INDUSTRIES to be certified by National Nuclear Safety Administration.%  针对核电压力容器用SA-508-3-1钢的组织与性能特点,分析出冶炼的难点,通过对冶炼工艺的深入研究,提出了采用EBT初炼—LF精炼—真空脱气—真空浇注的冶炼工艺方案,按该工艺方案成功冶炼浇注了核电SA-508-3-1钢锭。经过锻造及热处理等工序后,锻件性能达到核电压力容器锻件要求,并获得国家核安全局认证。

  7. Trace element partitioning and soil particle characterisation around mining and smelting areas at Tharsis, Riotinto and Huelva, SW Spain

    Energy Technology Data Exchange (ETDEWEB)

    Chopin, E.I.B. [School of Human and Environmental Sciences, University of Reading (United Kingdom)]. E-mail: edith.chopin@univ-reims.fr; Alloway, B.J. [School of Human and Environmental Sciences, University of Reading (United Kingdom)

    2007-02-15

    Trace elements may present an environmental hazard in the vicinity of mining and smelting activities. However, the factors controlling trace element distribution in soils around ancient and modern mining and smelting areas are not always clear. Tharsis, Riotinto and Huelva are located in the Iberian Pyrite Belt in SW Spain. Tharsis and Riotinto mines have been exploited since 2500 B.C., with intensive smelting taking place. Huelva, established in 1970 and using the Flash Furnace Outokumpu process, is currently one of the largest smelter in the world. Pyrite and chalcopyrite ore have been intensively smelted for Cu. However, unusually for smelters and mines of a similar size, the elevated trace element concentrations in soils were found to be restricted to the immediate vicinity of the mines and smelters, being found up to a maximum of 2 km from the mines and smelters at Tharsis, Riotinto and Huelva. Trace element partitioning (over 2/3 of trace elements found in the residual immobile fraction of soils at Tharsis) and soil particles examination by SEM-EDX showed that trace elements were not adsorbed onto soil particles, but were included within the matrix of large trace element-rich Fe silicate slag particles (i.e. 1 mm o at least 1 wt.% As, Cu and Zn, and 2 wt.% Pb). Slag particle large size (1 mm o) was found to control the geographically restricted trace element distribution in soils at Tharsis, Riotinto and Huelva, since large heavy particles could not have been transported long distances. Distribution and partitioning indicated that impacts to the environment as a result of mining and smelting should remain minimal in the region.

  8. Processing of 3-Dimensional Flash Lidar Terrain Images Generated From an Airborne Platform

    Science.gov (United States)

    Bulyshev, Alexander; Pierrottet, Diego; Amzajerdian, Farzin; Busch, George; Vanek, Michael; Reisse, Robert

    2009-01-01

    Data from the first Flight Test of the NASA Langley Flash Lidar system have been processed. Results of the analyses are presented and discussed. A digital elevation map of the test site is derived from the data, and is compared with the actual topography. The set of algorithms employed, starting from the initial data sorting, and continuing through to the final digital map classification is described. The accuracy, precision, and the spatial and angular resolution of the method are discussed.

  9. Smelting of Scandium by Microwave Irradiation

    Directory of Open Access Journals (Sweden)

    Satoshi Fujii

    2017-09-01

    Full Text Available Scandium is being explored as an alloying element for aluminum alloys, which are gaining importance as high-performance lightweight structural alloys in the transportation industry. A few years ago, Sc was also found to be suitable for use in electrical devices. High-Sc-content ScAlN thin films have attracted significant attention because of their strong piezoelectricity. The piezoelectric response of ScAlN suggests that ScAlN thin films formed on a hard substrate would be suitable surface acoustic wave wideband filters for next-generation wireless communication systems. However, it is often difficult to use ScAlN thin films in MEMS devices—including acoustic ones—because of the extremely high price of metallic Sc, given the difficulty associated with smelting it. Here, we propose a novel process for smelting Sc metal by microwave irradiation. Sc metal was able to be obtained successfully from ScF3 through a microwave-irradiation-based carbon reduction reaction. The reaction temperature for this reduction process was approximately 880°C, which is half of that for the conventional smelting process involving reduction with Ca. Thus, the proposed microwave irradiation process has significant potential for use in the smelting of Sc metal.

  10. Flash pyrolysis, a process for utilizing contaminated wood; Flash-Pyrolyse - eine Moeglichkeit der stofflichen Verwertung von kontaminiertem Holz

    Energy Technology Data Exchange (ETDEWEB)

    Meier, D.; Wehlte, S.; Faix, O. [Bundesforschungsanstalt fuer Forst- und Holzwirtschaft, Hamburg (Germany). Inst. fuer Holzchemie und Chemische Technologie des Holzes

    1996-12-31

    Flash pyrolysis of wood treated with common pesticides poses no technical probelms. Product yields, with a maximum oil yield at 475 C, are similar to those of untreated wood. Most of the heavy metals are retained by the coal while a small part aheres to the coal layer of the sand bed. The resulting pyrolysis oil contains neither chromium nor copper. (orig) [Deutsch] Die Flash-Pyrolyse der mit den gaengigsten Schutzmitteln behandelten Hoelzer bereitet verfahrenstechnisch keine Probleme. Auch die Produktausbeuten, mit einem oelmaximum bei 475 C, aehneln denen von naturbelassenem Holz. Der groesste Teil der Schwermetalle wurde an die Kohle gebunden, ein geringer Teil blieb auf der Kohleschicht des Sandes haften. Im Hauptprodukt Pyrolyseoel konnten weder Chrom noch Kupfer nachgewiesen werden. (orig)

  11. The Smelting Method of Blister Copperout of Copper Sulifde Concentrate%一种从硫化铜精矿中冶炼粗铜的方法

    Institute of Scientific and Technical Information of China (English)

    刘刚

    2016-01-01

    介绍了一种从硫化铜精矿中冶炼粗铜的方法,使用氧气顶吹转炉冶炼,对硫化铜精矿进行闪速熔炼产出铜锍,对铜锍采用空气吹炼产出粗铜。本方法设备投资小,工艺流程短,适应小规模铜精矿冶炼粗铜,富集有价金属的要求。%This paper introduces the smelting method of blister copper from copper sulfide concentrate by using oxygen top-blown converter. It uses oxygen top blown converter to smelt, and flash smelts the copper sulphide concentrate to produce copper matte, and then air blows copper matte to produce blister. This method is suitable for small scale blister-smelting out of copper concentrate and meets with the requirement of enriching valuable metal, in which the equipment investment is small, and the process is short.

  12. Oxidation Potentials in Matte Smelting of Copper and Nickel

    Science.gov (United States)

    Matousek, Jan W.

    2014-09-01

    The oxidation potential, given as the base-ten logarithm of the oxygen partial pressure in bars and the temperature [log pO2/ T, °C], defines the state of oxidation of pyrometallurgical extraction and refining processes. This property varies from copper making, [-6/1150]; to lead/zinc smelting, [-10/1200]; to iron smelting, [-13/1600]. The current article extends the analysis to the smelting of copper and nickel/copper sulfide concentrates to produce mattes of the type Cu(Ni)FeS(O) and iron silicate slags, FeOxSiO2—with oxidation potentials of [-7.5/1250].

  13. Applies in the non-ferrous smelting industry of process analysis integrated system%应用于有色冶炼工业的过程分析成套系统

    Institute of Scientific and Technical Information of China (English)

    周立仁; 梁明燕

    2012-01-01

    Application of process analysis systems in non-ferrous smelting industry is more and more widely, for guiding the safety process control energy saving environmental protection monitoring and improving economic efficiency plays a vital role. Based on the used in the process of smelting furnace exit flue gas analysis of complete system components discussion of the role of theory fully demonstrated the complete system in the smelting process analysis.%过程分析成套系统在有色冶炼工业中的应用越来越广泛,对于指导安全生产、工艺控制、节能降耗、环保监测以及提高企业经济效益方面都起着至关重要的作用.本文通过对应用于熔炼电炉出口烟气过程分析成套系统的组成、原理及作用的论述,论证了过程分析成套系统在熔炼电炉烟气分析中应用的可靠性和必要性.

  14. The Concept of Slag Decopperisation in the Flash Furnace Process by Use of Complex Reagents

    Directory of Open Access Journals (Sweden)

    Bydałek A.W.

    2015-04-01

    Full Text Available The article presents an outline of the new technology of pyrometallurgical processing of slag in the direct-to-blister process. The analysis is based on the example of the production process of KGHM Polish Copper SA. A new way of implementing the technology of recovery of copper from the flash furnace slag by means of different feedstocks has been proposed. The method of controlling the processes is another innovation discussed in the paper. The presented concept intensify the reduction reactions, using the Carbo-N-Ox method, of copper compounds to forms of metallic phases in the slag. The processes of coagulation are accelerated and the processes crystallization of metallic phases are under control.

  15. Study on the Behavior and Distribution of Arsenic in Tin Smelting Process in Laibin Smeltery%来冶锡系统中砷的行为和分布的研究

    Institute of Scientific and Technical Information of China (English)

    王伟

    2012-01-01

    锡冶炼过程中,杂质砷主要来源于锡精矿。杂质砷在锡冶炼流程中不及时开路,将反复积累,恶性循环,严重影响锡冶炼厂各项技术经济指标和经济效益。因此,杂质砷的及时、有效开路是提高技术经济指标,降低生产成本,提高经济效益的关键之一。文章根据广西华锡集团来宾华锡冶炼有限公司生产实践进行研究,论述了杂质砷在锡冶炼各主要工序中的行为和分布。指出了杂质砷在锡冶炼流程中大量循环对生产的影响,提出了砷开路的初步建议。%In tin smelting process, impurity arsenic mainly comes from tin concetrate. Arsenic will be accumulated, if it can't be removed from process timely, this will lead to a vicious circle and deeply effect the technical and economic index and the economic benefits of tin smeltery. Therefore, removing arsenic timely and efficaciously is the key to improve technical and economic index and reduce production cost. According the study on the production practice in Guangxi Laibin Huaxi Smelting Co., Ltd, this pape discusses the behavior and distribution of arsenic in tin smelting process and indicates the impact of abundant arsenic circulating in smelting process upon production, it also puts forward the suggestions of arsenic removal.

  16. Viscosity and structure evolution of the SiO2-MgO-FeO-CaO-Al2O3 slag in ferronickel smelting process from laterite

    Directory of Open Access Journals (Sweden)

    Lv X.M.

    2017-01-01

    Full Text Available The SiO2 fractions in laterite-nickel ores are quite high, thus certain amount of lime should be used as fluxing material to achieve good fluidity and desulfurization capacity in industrial smelting process. However, this operation leads to an additional cost of lime. In addition, the increase of slag volume decreases the effective furnace volume. To avoid such problem, partial reduction of FeO has been suggested. Therefore, the high SiO2, low MgO and FeO and very little CaO slag is formed, which was less studied in the previous literature. Therefore, the viscosity and slag structure are investigated in the present study through FT-IR and Raman analysis methods. Experimental results show that the slag is a mixture of liquid and solid phases under the experimental temperature. The FT-IR and Raman spectra show that the fractions of the complex polymerization structure decrease significantly with the increase of FeO content and slag basicity, resulting in the decrease of apparent viscosity.

  17. Foundation Flash Catalyst

    CERN Document Server

    Goralski, Greg

    2010-01-01

    This book offers an introduction to Flash Catalyst for designers with intermediate to advanced skills. It discusses where Catalyst sits within the production process and how it communicates with other programs. It covers all of the features of the Flash Catalyst workspace, teaching you how to create designs from scratch, how to build application designs and add functionality, and how to master the Catalyst/Flex workflow. * Introduces Flash Catalyst * Focuses on production process * Covers the interrelation between Flash Catalyst and Photoshop/Illustrator/Flex/Flash What you'll learn Starting f

  18. Audition influences color processing in the sound-induced visual flash illusion

    OpenAIRE

    Mishra, Jyoti; Martinez, Antigona; Hillyard, Steven A.

    2013-01-01

    Multisensory interactions can lead to illusory percepts, as exemplified by the sound-induced extra flash illusion (SIFI: Shams et al., 2000, 2002). In this illusion, an audio-visual stimulus sequence consisting of two pulsed sounds and a light flash presented within a 100 ms time window generates the visual percept of two flashes. Here, we used colored visual stimuli to investigate whether concurrent auditory stimuli can affect the perceived features of the illusory flash. Zero, one or two pu...

  19. Comparative hazard analysis of processes leading to remarkable flash floods (France, 1930-1999)

    Science.gov (United States)

    Boudou, M.; Lang, M.; Vinet, F.; Cœur, D.

    2016-10-01

    Flash flood events are responsible for large economic losses and lead to fatalities every year in France. This is especially the case in the Mediterranean and oversea territories/departments of France, characterized by extreme hydro-climatological features and with a large part of the population exposed to flood risks. The recurrence of remarkable flash flood events, associated with high hazard intensity, significant damage and socio-political consequences, therefore raises several issues for authorities and risk management policies. This study aims to improve our understanding of the hazard analysis process in the case of four remarkable flood events: March 1930, October 1940, January 1980 and November 1999. Firstly, we present the methodology used to define the remarkability score of a flood event. Then, to identify the factors leading to a remarkable flood event, we explore the main parameters of the hazard analysis process, such as the meteorological triggering conditions, the return period of the rainfall and peak discharge, as well as some additional factors (initial catchment state, flood chronology, cascade effects, etc.). The results contribute to understanding the complexity of the processes leading to flood hazard and highlight the importance for risk managers of taking additional factors into account.

  20. Plant Practice of Copper Oxygen Enrichment Side-Blowing Bath Smelting Process%铜富氧侧吹熔池熔炼的生产实践

    Institute of Scientific and Technical Information of China (English)

    葛晓鸣; 王举良

    2011-01-01

    The chemical composition of slag from oxygen enrichment side-blowing bath smelting process ( OES-BBSP) was confirmed according to the slag composition of Ausmelt furnace, Isaac furnace and Mitsubishi furnace. The problems which occurred during OESBBSP practice included high monomer sulfur content in waste gas, large vibration in furnace body and waste heat boiler, serious accretion in ascent stage and radiation area of waste heat boiler, condensation acid emerged in waste gas, lessening copper recovery due to a larger amount of smoke dust. With the effort of two years' improvement, the daily processing amount of copper concentrate, blister copper output , power and coal consumption, comprehensive energy consumption and production cost all met the design requirements.%根据奥斯麦特炉、艾萨炉、三菱炉的熔炼炉渣的化学成分,确定了富氧侧吹熔池熔炼炉渣的化学成分.富氧侧吹熔池熔炼炉投产过程中出现的问题主要有:烟气中单体硫含量高、炉体和余热锅炉振动较大、余热锅炉上升段和辐射区炉结较重、烟气产生冷凝酸、烟尘量较大降低了铜直收率和铜回收率.经过两年的改进,日处理铜精矿量、粗铜日产量、电单耗、煤单耗、综合能耗和生产成本均达到设计要求.

  1. 某含金汞冶炼渣浮选试验%Flotation Process of a Gold-bearing Mercury Smelting Slag

    Institute of Scientific and Technical Information of China (English)

    傅开彬; 涂昌能; 王维清; 冯启明; 黄阳

    2013-01-01

    某含金1.85 g/t的汞冶炼渣中金主要以游离微细金和硫化物包裹金的形式存在,对该二次资源进行了浮选回收金的试验研究.结果表明,在磨矿细度为-0.074 mm占80%的情况下,采用1粗2精2扫、中矿顺序返回流程处理该试样,可以获得金品位为28.65 g/t、回收率为68.45%的金精矿,导致金回收率不高的主要原因是金颗粒微细和被碳酸盐、褐铁矿、石英和硅酸盐等矿物包裹.%Gold exists in the form of free fine gold and gold-wrapped sulfide in mercury smelting slag with gold bearing of 1. 85 g/t. Research on recovering gold by flotation from the secondary resources was carried out. The research results showed that under grinding fineness of — 0. 074 mm 80% , gold concentrate with gold grade of 28. 65 g/t, and recovery of 68. 45% was obtained by the flow sheet of one-roughing, two-cleaning, three-scavenging and middles back to the process in order. The main reasons resulting in low gold recovery are that gold occurs in ultra-fine particles or was wrapped by carbonates, limonite, quartz and silicate.

  2. In situ monitoring of a flash light sintering process using silver nano-ink for producing flexible electronics

    Science.gov (United States)

    Chung, Wan-Ho; Hwang, Hyun-Jun; Lee, Seung-Hyun; Kim, Hak-Sung

    2013-01-01

    In this work, a flash light sintering process using silver nano-inks is investigated. A silver nano-ink pattern was printed on a flexible PET (polyethylene terephthalate) substrate using a gravure-offset printing system. The printed silver nano-ink was sintered at room temperature and under ambient conditions using a flash of light from a xenon lamp using an in-house flash light sintering system. In order to monitor the light sintering process, a Wheatstone bridge electrical circuit was devised and changes in the voltage difference of the silver nano-ink were recorded during the sintering process using an oscilloscope. The sheet resistance changes during the sintering process were monitored using the in situ monitoring system devised, under various light conditions (e.g. light energy, on-time and off-time duration, and pulse numbers). The microstructure of the sintered silver film and the interface between the silver film and the PET substrate were observed using a scanning electron microscope, a focused ion beam and an optical microscope. The electrical sheet resistances of the sintered silver films were measured using a four-point probe method. Using the in situ monitoring system devised, the flash light sintering mechanism was studied for each type of light pulse (e.g. evaporation of organic binder followed by the forming of a neck-like junction and its growth, etc). The optimal flash light sintering condition is suggested on the basis of the in situ monitoring results. The optimized flash light sintering process produces a silver film with a lower sheet resistance (0.95 Ω/sq) compared with that of the thermally sintered silver film (2.03 Ω/sq) without damaging the PET substrate or allowing interfacial delamination between the silver film and the PET substrate.

  3. Understanding processes that generate flash floods in the arid Judean Desert to the Dead Sea - a measurement network

    Science.gov (United States)

    Hennig, Hanna; Rödiger, Tino; Laronne, Jonathan B.; Geyer, Stefan; Merz, Ralf

    2016-04-01

    Flash floods in (semi-) arid regions are fascinating in their suddenness and can be harmful for humans, infrastructure, industry and tourism. Generated within minutes, an early warning system is essential. A hydrological model is required to quantify flash floods. Current models to predict flash floods are often based on simplified concepts and/or on concepts which were developed for humid regions. To more closely relate such models to local conditions, processes within catchments where flash floods occur require consideration. In this study we present a monitoring approach to decipher different flash flood generating processes in the ephemeral Wadi Arugot on the western side of the Dead Sea. To understand rainfall input a dense rain gauge network was installed. Locations of rain gauges were chosen based on land use, slope and soil cover. The spatiotemporal variation of rain intensity will also be available from radar backscatter. Level pressure sensors located at the outlet of major tributaries have been deployed to analyze in which part of the catchment water is generated. To identify the importance of soil moisture preconditions, two cosmic ray sensors have been deployed. At the outlet of the Arugot water is sampled and level is monitored. To more accurately determine water discharge, water velocity is measured using portable radar velocimetry. A first analysis of flash flood processes will be presented following the FLEX-Topo concept .(Savenije, 2010), where each landscape type is represented using an individual hydrological model according to the processes within the three hydrological response units: plateau, desert and outlet. References: Savenije, H. H. G.: HESS Opinions "Topography driven conceptual modelling (FLEX-Topo)", Hydrol. Earth Syst. Sci., 14, 2681-2692, doi:10.5194/hess-14-2681-2010, 2010.

  4. 铅冶炼技术的发展现状及旋涡闪速炼铅工艺%Development Status of Lead Smelting Technology and the Lead Vortex Flash Smelting Process

    Institute of Scientific and Technical Information of China (English)

    汪金良; 吴艳新; 张文海

    2011-01-01

    铅是发展国民经济的重要基础原材料,然而,传统的烧结-鼓风炉熔炼工艺具有能耗大和污染重等缺陷,因此,加快铅冶炼技术的科技进步对整个国民经济的可持续发展具有重要意义.文中综述了Kivcet法、QSL法、Kaldo法、Ausmelt/Isasmelt法、SKS法等国内外直接炼铅新工艺,重点介绍了具有我国自主知识产权的旋涡闪速炼铅工艺过程、主要设备及技术特点.

  5. The pH-dependent leaching behavior of slags from various stages of a copper smelting process: Environmental implications.

    Science.gov (United States)

    Jarošíková, Alice; Ettler, Vojtěch; Mihaljevič, Martin; Kříbek, Bohdan; Mapani, Ben

    2017-02-01

    The leaching behaviors of primary copper (Cu) slags originating from Ausmelt, reverbatory, and converter furnaces operating under a single technological process were compared to a residual slag tailing obtained by slag re-processing via flotation and metal recovery. The EN 12457-2 leaching test, used for assessment of the hazardous properties, was followed by the CEN/TS 14997 pH-static leaching test (pH range 3-12). Both leaching experiments were coupled with a mineralogical investigation of the primary and secondary phases as well as geochemical modeling. Metals (Cd, Cu, Pb, Zn) exhibit the highest leaching at low pH. Under acidic conditions (pH 3-6), Ausmelt slag and slag tailing exhibited higher metal leaching compared to other slag types. Very low leaching of metals (far below EU limits for non-hazardous waste) was observed at natural pH (7.9-9.0) for all the studied slag samples. In contrast, relatively high leaching of As was observed over the entire pH range, especially for Ausmelt slag (exceeding the EU limit for hazardous waste by 1.7×). However, geochemical modeling and scanning electron microscopy indicated that formation of stable Ca-Cu-Pb arsenates and the binding of As to newly formed Fe (oxyhydr)oxides play an important role in efficient As immobilization at the slag-water interface. In contrast, no controls were predicted for Sb, whose leaching was almost pH-independent. Nevertheless Sb leached concentrations at natural pH were below EU limit for hazardous waste. Re-processing of primary Cu slags for metal recovery, and subsequent co-disposal of the resulting slag tailing with dolomite-rich mine tailing and local laterite is suitable for stabilizing the remaining contaminants (except Sb) and limiting their leaching into the environment. Copyright © 2016 Elsevier Ltd. All rights reserved.

  6. Processes and Geomorphological Impacts of an Extreme Flash Flood Event in SE Spain

    Science.gov (United States)

    Hooke, J.

    2015-12-01

    A major flash flood event took place on 28 September, 2012 in SE Spain, resulting in 10 fatalities and much damage to infrastructure regionally. The flood affected long-term monitoring sites in two catchments in which morphological changes and flow dynamics of these ephemeral channels were being measured. Thus detailed data on channel state prior to the flood were available. The flood event in the Nogalte catchment was extreme in its peak flow, rate of rise and unit runoff. The catchment has steep relief and much bare soil under almond groves, resulting in high sediment supply. The channel is confined in places, but mostly wide and braided, composed of loose gravel and occupying much of the valley floor. Flow was spatially continuous, with high connectivity throughout the catchment. The flood effects were net depositional in the monitored sites, with massive sedimentation on the channel bars. Vegetation was destroyed. Bank erosion and destruction of embankments took place in some locations. Hydraulic calculations indicate very high velocities, stream power and Froude numbers. Modelling and field evidence demonstrate extremely high sediment competence and sediment loadings. The influence of the event dynamics on processes and net outcomes is discussed. The impacts are compared with other events in this and neighbouring catchments. Overall, the event in the Nogalte did not alter the morphology markedly in spite of its extreme characteristics. It is suggested that these valley floors are adapted to this type of flash flood but that flows of such force and magnitude need to be allowed for in management in such an environment.

  7. 300MW及以上汽轮机低压转子冶炼工艺研究%Smelting Process of Steam Turbine Low Pressure Rotor of 300 MW & Above

    Institute of Scientific and Technical Information of China (English)

    魏雪晴; 李奇; 管仲毅

    2014-01-01

    介绍了300 MW及以上汽轮机低压转子的冶炼工艺控制要点。对耐火材料和辅具进行了改进和优化,最终生产出合格的转子锻件。%This paper presents the smelting process control key points of 300 MV and above steam turbine low pressure rotor .Refractory materials and auxiliary tools have been improved and optimized , eventually acceptable rotor has been produced .

  8. NAND flash memory technologies

    CERN Document Server

    Aritome, Seiichi

    2016-01-01

    This book discusses basic and advanced NAND flash memory technologies, including the principle of NAND flash, memory cell technologies, multi-bits cell technologies, scaling challenges of memory cell, reliability, and 3-dimensional cell as the future technology. Chapter 1 describes the background and early history of NAND flash. The basic device structures and operations are described in Chapter 2. Next, the author discusses the memory cell technologies focused on scaling in Chapter 3, and introduces the advanced operations for multi-level cells in Chapter 4. The physical limitations for scaling are examined in Chapter 5, and Chapter 6 describes the reliability of NAND flash memory. Chapter 7 examines 3-dimensional (3D) NAND flash memory cells and discusses the pros and cons in structure, process, operations, scalability, and performance. In Chapter 8, challenges of 3D NAND flash memory are dis ussed. Finally, in Chapter 9, the author summarizes and describes the prospect of technologies and market for the fu...

  9. Electrical properties of BaZrO3 ceramic synthesized by flash pyrolysis process

    Science.gov (United States)

    Saini, Deepash S.; Bhattacharya, D.

    2016-04-01

    Barium Zirconate (BaZrO3) nanoparticles are synthesized by flash pyrolysis combustion process. Rietveld refinement of XRD pattern of calcined powder at 900 °C, 1100 °C and sintered at 1600 °C describes that a single-phase compound is formed of an Pm-3m cubic crystal structure with a lattice constant a = 4.19102, 4.192693, and 4.195276 Å respectively. Crystallize size of calcined powder at 900 °C, 1100 °C and sintered at 1600 °C is found 34.28, 37.7 and 47.14 nm respectively using Scherrer formula. The FESEM image of sintered pellet at 1600 °C for 4 h describes porous nature of the sample. The Nyquist plots indicate the dominant grain boundary effect in electrical processes in the sample. A decrease in the bulk resistance with increasing temperature demonstrates a semiconducting behavior. The temperature dependent relaxation and conduction mechanism brief involvements of different types of the charge species in the 250 to 500 °C temperature region as studied at different frequencies over 100 Hz to 1 MHz.

  10. Mass retention efficiency and i-process nucleosynthesis in He-shell flash evolution of rapidly accreting white dwarfs

    CERN Document Server

    Denissenkov, Pavel; Battino, Umberto; Ritter, Christian; Pignatari, Marco; Jones, Samuel; Paxton, Bill

    2016-01-01

    Based on stellar evolution simulations, we demonstrate that rapidly accreting white dwarfs (RAWDs) in close binary systems, like those considered in the single-degenerate progenitor channel of type Ia supernovae, experience recurrent and very strong He-shell flashes in the stable H-burning accretion regime. The He-shell flashes result in the expansion and, utimately, ejection of the newly-accreted material via super-Eddington luminosity winds or Roche-lobe overflow. The white dwarf models do not retain any significant amount of the accreted mass, with a He retention efficiency of < 10% depending on mass and convective boundary mixing assumptions. This makes the evolutionary path of such systems to supernova Ia explosion highly unlikely. Instead, we have discovered that such binary systems are an astrophysical site for the intermediate neutron-capture process. In each of the He-shell flashes H-rich material enters the He-shell flash convection zone. 1D stellar evolution simulations of RAWDs show the H-inges...

  11. Characterization of process-oriented hydrologic model behavior with temporal sensitivity analysis for flash floods in Mediterranean catchments

    Directory of Open Access Journals (Sweden)

    P. A. Garambois

    2013-06-01

    Full Text Available This paper presents a detailed analysis of 10 flash flood events in the Mediterranean region using the distributed hydrological model MARINE. Characterizing catchment response during flash flood events may provide new and valuable insight into the dynamics involved for extreme catchment response and their dependency on physiographic properties and flood severity. The main objective of this study is to analyze flash-flood-dedicated hydrologic model sensitivity with a new approach in hydrology, allowing model outputs variance decomposition for temporal patterns of parameter sensitivity analysis. Such approaches enable ranking of uncertainty sources for nonlinear and nonmonotonic mappings with a low computational cost. Hydrologic model and sensitivity analysis are used as learning tools on a large flash flood dataset. With Nash performances above 0.73 on average for this extended set of 10 validation events, the five sensitive parameters of MARINE process-oriented distributed model are analyzed. This contribution shows that soil depth explains more than 80% of model output variance when most hydrographs are peaking. Moreover, the lateral subsurface transfer is responsible for 80% of model variance for some catchment-flood events' hydrographs during slow-declining limbs. The unexplained variance of model output representing interactions between parameters reveals to be very low during modeled flood peaks and informs that model-parsimonious parameterization is appropriate to tackle the problem of flash floods. Interactions observed after model initialization or rainfall intensity peaks incite to improve water partition representation between flow components and initialization itself. This paper gives a practical framework for application of this method to other models, landscapes and climatic conditions, potentially helping to improve processes understanding and representation.

  12. Considerations for Scale-Up of Ferronickel Electric Smelting Furnaces

    Science.gov (United States)

    Hundermark, R. J.; Nelson, L. R.

    2017-02-01

    In ferronickel smelting, the selective carbothermic reduction of calcined nickel laterite ores in large electric furnaces yields a crude ferronickel product. The optimal process for nickel laterite smelting requires a fine balance between the metallurgical requirements of the process (feed composition, nickel recovery, energy consumption, product quality) and the capabilities of the feeding, tapping and off-gas systems, and especially of the furnace crucible and electrical system. The scale-up of nickel laterite smelting operations over the last 50 years has seen a tenfold increase in furnace power input. Furnace operations within the industry are examined to identify common trends and some new metrics are proposed which incorporate the combination of electrode power densities and the impact of alloy nickel grade on gas generation rates, and hence local electrode gas fluxes, which may impact on future scale-up of ferronickel furnaces.

  13. Investigation and process optimization of SONOS cell's drain disturb in 2-transistor structure flash arrays

    Science.gov (United States)

    Xu, Zhaozhao; Qian, Wensheng; Chen, Hualun; Xiong, Wei; Hu, Jun; Liu, Donghua; Duan, Wenting; Kong, Weiran; Na, Wei; Zou, Shichang

    2017-03-01

    The mechanism and distribution of drain disturb (DD) are investigated in silicon-oxide-nitride-oxide-silicon (SONOS) flash cells. It is shown that DD is the only concern in this paper. First, the distribution of trapped charge in nitride layer is found to be non-localized (trapped in entire nitride layer along the channel) after programming. Likewise, the erase is also non-localized. Then, the main disturb mechanism: Fowler Nordheim tunneling (FNT) has been confirmed in this paper with negligible disturb effect from hot-hole injection (HHI). And then, distribution of DD is confirmed to be non-localized similarly, which denotes that DD exists in entire tunneling oxide (Oxide for short). Next, four process optimization ways are proposed for minimization of DD, and VTH shift is measured. It reveals that optimized lightly doped drain (LDD), halo, and channel implant are required for the fabrication of a robust SONOS cell. Finally, data retention and endurance of the optimized SONOS are demonstrated.

  14. Breaking continuous flash suppression: A new measure of unconscious processing during interocular suppression?

    Directory of Open Access Journals (Sweden)

    Timo eStein

    2011-12-01

    Full Text Available Until recently, it has been thought that under interocular suppression high-level visual processing is strongly inhibited if not abolished. With the development of continuous flash suppression (CFS, a variant of binocular rivalry, this notion has now been challenged by a number of reports showing that even high-level aspects of visual stimuli, such as familiarity, affect the time stimuli need to overcome CFS and emerge into awareness. In this breaking CFS (b-CFS paradigm, differential unconscious processing during suppression is inferred when (a speeded detection responses to initially invisible stimuli differ, and (b no comparable differences are found in non-rivalrous control conditions supposed to measure general threshold differences between stimuli. To critically evaluate these assumptions was the aim of the present study. In six experiments we compared the time upright and inverted faces needed to be detected. We found that not only under CFS, but also in control conditions upright faces were detected faster and more accurately than inverted faces, although the effect was larger during CFS. However, reaction time (RT distributions indicated critical differences between the CFS and the control condition. When RT distributions were matched, similar effect sizes were obtained in both conditions. Moreover, subjective ratings revealed that CFS and control conditions are not perceptually comparable. These findings cast doubt on the usefulness of non-rivalrous control conditions to rule out mere detection threshold differences as a cause of shorter detection latencies during CFS. In conclusion, we acknowledge that the b-CFS paradigm can be fruitfully applied as a highly sensitive device to probe differences between stimuli in their potency to gain access to awareness. However, our current findings suggest that such differences can not unequivocally be attributed to differential unconscious processing under interocular suppression.

  15. OPTIMIZATION OF CONVERTER SMELTING PROCESS FOR HIGH-SILICON HIGH-TITANIUM HOT METAL%转炉高硅高钛铁水冶炼工艺优化

    Institute of Scientific and Technical Information of China (English)

    张锦兴; 田宝义

    2015-01-01

    To solve the problems of converter of Medium and Heavy Plate Company of Tang Steel in smelting with high-silicon high-titanium hot metal:difficult operation, converter spitting occurring some time and causing low receive efficiency of metals, the smelting process is optimized in aspects of charging system, ox-ygen feeding system and slag making system.After that the converter spitting rate is reduced from 4.3 to 1 percent, the iron and steel materials consumption lowered by 2.15 kg/t, excellent economic and environment profit got.%针对唐钢中厚板公司转炉入炉铁水硅高钛高、转炉操作难度较大、易发生转炉喷溅导致金属收得率低的问题,从装入制度、供氧制度和造渣制度等方面对高硅高钛铁水冶炼工艺进行了优化. 改进后,转炉喷溅率由4.3%降至1%,钢铁料消耗降低了2.15 kg/t,取得了显著的经济效益和环境效益.

  16. Silver Recovery from Acid Leaching Slag of Zinc Smelting with Hydrometallurgical Process%全湿法工艺回收锌冶炼酸浸渣中的银

    Institute of Scientific and Technical Information of China (English)

    王康柱; 王正民; 周熙; 周玺

    2013-01-01

    锌冶炼酸浸渣先浮选再用硫脲富集获得粗银绵,粗银绵经化学法提纯后经过电解产出纯度达99.95%以上的成品银,全流程银回收率达到70%以上.还可同时回收金和铜,含锌液返回锌冶炼系统,且无三废产生.%Crude silver powder was obtained by flotation and thiourea enrichment from acid leaching slag of zinc smelting.Crude silver powder was purified by chemical method and electrolyzed to produce silver product with purity of 99.95% plus.The silver recovery rate is more than 70%.Gold and copper are recovered simultaneously and zinc is returned to zinc smelting system.There are no three wastes in the whole process.

  17. Compositional Fragmentation Model for the Oxidation of Sulfide Particles in a Flash Reactor

    Science.gov (United States)

    Parra-Sánchez, Víctor Roberto; Pérez-Tello, Manuel; Duarte-Ruiz, Cirilo Andrés; Sohn, Hong Yong

    2014-04-01

    A mathematical model to predict the size distribution and chemical composition of a cloud of sulfide particles during high-temperature oxidation in a flash reactor is presented. The model incorporates the expansion and further fragmentation of the reacting particles along their trajectories throughout the reaction chamber. A relevant feature of the present formulation is its flexibility to treat a variety of flash reacting systems, such as the flash smelting and flash converting processes. This is accomplished by computing the chemical composition of individual particles and the size distribution and overall composition of the particle cloud in separate modules, which are coupled through a database of particle properties previously stored on disk. The flash converting of solid copper mattes is considered as an example. The model predictions showed good agreement with the experimental data collected in a large laboratory reactor in terms of particle size distribution and sulfur remaining in the population of particles. The cumulative contribution and distribution coefficients are introduced to quantify the relationship between specific particle sizes in the feed and those in the reacted products upon oxidation, the latter of which has practical implications on the amount and chemical composition of dust particles produced during the industrial operation.

  18. Rock Smelting of Copper Ores with Waste Heat Recovery

    Science.gov (United States)

    Norgate, Terry; Jahanshahi, Sharif; Haque, Nawshad

    It is generally recognised that the grades of metallic ores are falling globally. This trend can be expected to increase the life cycle-based energy requirement for primary metal production due to the additional amount of material that must be handled and treated in the mining and mineral processing stages of the metal production life cycle. Rock (or whole ore) smelting has been suggested as a possible alternative processing route for low grade ores with a potentially lower energy intensity and environmental impact than traditional processing routes. In this processing route, the beneficiation stage is eliminated along with its associated energy consumption and greenhouse gas emissions, but this is partially offset by the need for more solid material to be handled and heated up to smelting temperatures. A life cycle assessment study was carried out to assess the potential energy and greenhouse gas benefits of a conceptual flowsheet of the rock smelting process, using copper ore as an example. Recovery and utilisation of waste heat in the slag (via dry slag granulation) and offgas streams from the smelting step was also included in the study, with the waste heat being utilised either for thermal applications or electricity generation.

  19. Dual damascene BEOL processing using multilevel step and flash imprint lithography

    Science.gov (United States)

    Chao, Brook H.; Palmieri, Frank; Jen, Wei-Lun; McMichael, D. Hale; Willson, C. Grant; Owens, Jordan; Berger, Rich; Sotoodeh, Ken; Wilks, Bruce; Pham, Joseph; Carpio, Ronald; LaBelle, Ed; Wetzel, Jeff

    2008-03-01

    Step and Flash Imprint Lithography (S-FIL®) in conjunction with Sacrificial Imprint Materials (SIM) shows promise as a cost effective solution to patterning sub 45nm features and is capable of simultaneously patterning two levels of interconnect structures, which provides a high throughput and low cost BEOL process. This paper describes the integration of S-FIL into an industry standard Cu/low-k dual damascene process that is being practiced in the ATDF at Sematech in Austin. The pattern transferring reactive ion etching (RIE) process is the most critical step and was extensively explored in this study. In addition to successful process development, the results provide useful insight into the optimal design of multilevel templates which must take into account the characteristics of both the imaging material and the dielectric layer. The template used in this study incorporates both the via and trench levels of an M2 (Metal 2) test vehicle that incorporates via chains with varying via dimensions, Kelvin test structures, serpentines, etc. The smallest vias on the template are 120nm vias with an aspect ratio of 2.0 and the smallest dense lines are 125nm/175nm with an aspect ratio of 2.9. Two inter-level dielectrics (ILD), Coral® and Black Diamond® were studied. No trench etch stop was incorporated in the ILD film stack. A multi-step, in-situ etching scheme was developed that achieves faithful pattern transfer from the sacrificial imprint material (SIM) into the underlying low k ILD with surprisingly wide process latitude. This multi-step scheme includes the following etch steps: a residual layer open, a via etch, a trench descum, a trench etch, and an SIM removal ash. Among these steps, the trench etch was found to be the most challenging to develop and it holds the key to producing high aspect ratio dual damascene features. An etching chemistry based on two fluorocarbon gases, CF 4 and C 4F 8, was found to be very effective in delivering the desired etch profiles

  20. Formation and phase separation during the smelting of sulfide raw materials

    Science.gov (United States)

    Tarasov, A. V.; Paretsky, V. M.

    2009-10-01

    This paper discusses the most recent developments made at the Gintsvetmet Institute in technologies and equipment for single-stage autogenous smelting of copper sulfide raw materials to produce white metal and blister copper. In particular, the oxygen-flame smelting process and separation of highly basic calcium-containing slags are considered. This technology includes the oxygen-flame smelting process (KFP Process) to produce highly basic self-disintegrating ferrite-calcium slags with their subsequent flotation to recover copper. Also included is a sparging smelting process (FBP Process) to produce combined slags subjected to decopperizing inside the same furnace. Results of special investigations of the slag structure obtained in the KFP and FBP processes and substantiating selection of their chemical and phase composition are presented. These processes meet stringent requirements for advanced technologies with respect to energy conservation and environmental safety with different scales of production and within a wide range of specific conditions of particular operations.

  1. Hand Eczema and Its Risk Factors of Workers in Ferrous Metal Smelting and Calendering Processing Industry%黑色金属冶炼和压延加工业工人手部湿疹及其危险因素

    Institute of Scientific and Technical Information of China (English)

    贾宁; 秦汝莉; 李玉珍; 张雪艳; 李建国; 赵春香; 周久利; 王忠旭

    2012-01-01

    [目的]调查黑色金属冶炼和压延加工业工人手部湿疹的患病情况,探讨其相关危险因素. [方法]采用随机抽样方法,对某省11家黑色金属冶炼和压延加工企业工人手部湿疹的患病情况进行横断面调查,利用x2检验和多因素logistic回归进行手部湿疹的危险因素分析. [结果]该11家黑色金属冶炼和压延加工业工人手部湿疹的患病率为12.8%,其中从事热处理、造型和金属熔炼工序的工人手部湿疹的患病率较高,分别为26.8%、25.4%和25.0%.作业工人自诉生产性粉尘、金属及其盐类(锰及其化合物、铬及其化合物、镍化合物)、金属加工液、强酸(硫酸、硝酸、盐酸)、有机溶剂(苯及其同系物、三氯乙烯、四氯化碳)和高温为可能导致手部湿疹的危险因素.多元logistic 回归分析表明,金属加工液、男性、年龄、全身皮肤干燥、皮肤过敏史和哮喘史被选入模型.其中,金属加工液的OR值( 5.007)最高.[结论]黑色金属冶炼和压延加工业工人手部湿疹的患病率较高,应积极采取切实有效的防护措施,减少和预防该病的发生.%[ Objective ] To estimate the prevalence of hand eczema among workers of ferrous metal smelting and calendering processing industry, and to explore related risk factors. [ Methods ] A cross-sectional study was conducted among workers with hand eczema randomly selected from 11 ferrous metal smelting and calendering processing enterprises in a province of China. The x2 test and multivariate logistic regression analysis were used to analyze risk factors of hand eczema. [ Results ] Of the workers investigated, the prevalence rate of hand eczema was 12.8%, and higher prevalences of hand eczema were found in workers engaged in heat treatment, moulding and smelting procedures, being 26.8%, 25.4% and 25.0%, respectively. Their self-reported risk factors of hand eczema were productive dust, metals and their salts (manganese

  2. Simulation of Flash Separation in Polyethylene Industrial Processing: Comparison of SRK and SL Equations of State

    OpenAIRE

    Costa, Glória Meyberg Nunes; Guerrieri, Y.; Kislansky, S.; F.L.P. Pessoa; Melo, Silvio Alexandre Beisl Vieira de; Embiruçu, Marcelo

    2009-01-01

    Texto completo: Acesso restrito. p. 8613–8628. The Soave−Redlich−Kwong (SRK) and the Sanchez and Lacombe (SL) equations of state are applied to the flash simulation of polyethylene industrial separators, specifically low-density polyethylene (eight resins) and linear low-density polyethylene (25 resins). Three mixing rules are used in the SRK equation: van der Waals (VDW) one-fluid, Wong−Sandler, and LCVM (linear combination of the Vidal and Michelsen mixing rules). The latter two mixing r...

  3. China Curbs the Investment in Copper Smelting

    Institute of Scientific and Technical Information of China (English)

    2006-01-01

    <正>According to a recent document released by the State Development and Reform Commission (SDRC), the investment in copper smelting by China’s enterprises will be put under strict control so as to prevent the blind investment and duplication in copper smelting projects at low technical standard. The document stipulated a series of conditions including equipment, technology, energy consumption and environmental protection.

  4. Late Bronze age metallurgy in the Italian Eastern Alps: copper smelting slags and mine exploitation

    OpenAIRE

    2013-01-01

    At the end of the second millennium B.C., the extractive metallurgy of copper in Trentino (Italy) achieved a peak of technological efficiency and mass production, as evidenced by the large number of metallurgical sites and the huge amount of slags resulting from the smelting activities. Though different scholars proposed several smelting process models, so far an agreed interpretation of the whole process is lacking. Over 70 slags from the Luserna, Transacqua and Segonzano sites (all l...

  5. Flexible Design and Operation of Multi-Stage Flash (MSF Desalination Process Subject to Variable Fouling and Variable Freshwater Demand

    Directory of Open Access Journals (Sweden)

    Said Alforjani Said

    2013-10-01

    Full Text Available This work describes how the design and operation parameters of the Multi-Stage Flash (MSF desalination process are optimised when the process is subject to variation in seawater temperature, fouling and freshwater demand throughout the day. A simple polynomial based dynamic seawater temperature and variable freshwater demand correlations are developed based on actual data which are incorporated in the MSF mathematical model using gPROMS models builder 3.0.3. In addition, a fouling model based on stage temperature is considered. The fouling and the effect of noncondensable gases are incorporated into the calculation of overall heat transfer co-efficient for condensers. Finally, an optimisation problem is developed where the total daily operating cost of the MSF process is minimised by optimising the design (no of stages and the operating (seawater rejected flowrate and brine recycle flowrate parameters.

  6. Insight into the Physical and Dynamical Processes that Control Rapid Increases in Total Flash Rate

    Science.gov (United States)

    Schultz, Christopher J.; Carey, Lawrence D.; Schultz, Elise V.; Blakeslee, Richard J.; Goodman, Steven J.

    2015-01-01

    Rapid increases in total lightning (also termed "lightning jumps") have been observed for many decades. Lightning jumps have been well correlated to severe and hazardous weather occurrence. The main focus of lightning jump work has been on the development of lightning algorithms to be used in real-time assessment of storm intensity. However, in these studies it is typically assumed that the updraft "increases" without direct measurements of the vertical motion, or specification of which updraft characteristic actually increases (e.g., average speed, maximum speed, or convective updraft volume). Therefore, an end-to-end physical and dynamical basis for coupling rapid increases in total flash rate to increases in updraft speed and volume must be understood in order to ultimately relate lightning occurrence to severe storm metrics. Herein, we use polarimetric, multi-Doppler, and lightning mapping array measurements to provide physical context as to why rapid increases in total lightning are closely tied to severe and hazardous weather.

  7. Analysis of flash flood-triggering rainfall for a process-oriented hydrological model

    Science.gov (United States)

    Garambois, P. A.; Larnier, K.; Roux, H.; Labat, D.; Dartus, D.

    2014-02-01

    We propose an extended study of recent flood-triggering storms and resulting hydrological responses for catchments in the Pyrenean foothills up to the Aude region. For hydrometeorological sciences, it appears relevant to characterize flash floods and the storm that triggered them over various temporal and spatial scales. There are very few studies of extreme storm-caused floods in the literature covering the Mediterranean and highlighting, for example, the quickness and seasonality of this natural phenomenon. The present analysis is based on statistics that clarify the dependence between the spatial and temporal distributions of rainfall at catchment scale, catchment morphology and runoff response. Given the specific space and time scales of rainfall cell development, we show that the combined use of radar and a rain gauge network appears pertinent. Rainfall depth and intensity are found to be lower for catchments in the Pyrenean foothills than for the nearby Corbières or Montagne Noire regions. We highlight various hydrological behaviours and show that an increase in initial soil saturation tends to foster quicker catchment flood response times, of around 3 to 10 h. The hydrometeorological data set characterized in this paper constitutes a wealth of information to constrain a physics-based distributed model for regionalization purposes in the case of flash floods. Moreover, the use of diagnostic indices for rainfall distribution over catchment drainage networks highlights a unimodal trend in spatial temporal storm distributions for the entire flood dataset. Finally, it appears that floods in mountainous Pyrenean catchments are generally triggered by rainfall near the catchment outlet, where the topography is lower.

  8. Analyzing the transmission structures of long continuing current processes from negative ground flashes on the Qinghai-Tibetan Plateau

    Science.gov (United States)

    Fan, Xiangpeng; Zhang, Guangshu; Wang, Yanhui; Li, Yajun; Zhang, Tong; Wu, Bin

    2014-03-01

    This paper presents a new overlap and progressive method using either a one-point charge model or a point dipole model for studying the electric field change data of lightning and tests the suitability of the proposed method by analyzing the slow electric field change of the long continuing current data from two negative ground flashes. The current measurements of the ground flashes are from the Composite Observing Experiment for Lightning project carried out in the Datong region of Qinghai Province, China, in 2009, obtained from field observations synchronized through high-precision GPS clocks at seven observation stations. Analysis shows that the time-averaged current can reach 800 A, and the current intensity relates to the height of the top of the return stroke before the continuing current process. The two current processes studied in this work neutralized a large amount of negative charge, 39.5C and 60.8C, respectively. The neutralized charges from the negative charge layer are typically at 2.5-4.7 km above ground. The intracloud transition of the positive leader is a complex process, and the horizontal propagation of the positive leader plays an important role in current duration as well as horizontally influencing the center of the electrical dipole moment with an obvious change of up to 3.0 km. The proposed analysis method is very useful compared to previous methods in terms of determining infinitesimal changes in long continuing currents. This work's new analysis method will help increase understanding of the fine physical processes of long continuing current processes.

  9. Fabrication of gradient material by electron beam smelting based on scanning track control

    Institute of Scientific and Technical Information of China (English)

    YANG Shanglei; XUE Xiaohuai; LOU Songnian; LU Fenggui

    2007-01-01

    A new electron beam (EB) control system was developed in a general vacuum EB machine by equipping it with an industrial control computer, programmable logic control (PLC), deflection coil, data acquisition card, power amplifier, etc. In this control system, the scanning track and energy distribution of the EB could be edited off-line,adjusted in real-time, and controlled on-line. Ti-Mo gradient material (GM) with high temperature resistance was fabri-cated using electron beam smelting (EBS) control. The smelting processes include three steps such as preheating,smelting, and homogenizing. The results show that GM pre-pared by using smelting technology has fine appearance, and has good integrated interface with Ti alloy. The Mo and Ti elements are gradual diversification in the interface of the gradient material. The microstructure near the Ti alloy base metal is α + β basket-waver grain, and the microstructure near GM is single phase of β solid solution.

  10. 一种再生铅低温清洁冶金的绿色工艺%A Clean and Green Process of Low-Temperature for Smelting of Secondary Lead

    Institute of Scientific and Technical Information of China (English)

    胡宇杰; 唐朝波; 唐谟堂; 杨建广; 陈永明; 杨声海; 何静

    2013-01-01

    提出了一种低温、低碳、无二氧化硫烟气排放、清洁环保的绿色再生铅冶金新工艺.该工艺以纯碱为熔盐介质,含铅次氧化锌烟灰为固硫剂,以焦粉为还原剂,在800~900℃还原固硫熔炼废铅酸蓄电池胶泥生产粗铅,同时以合格的硫化锌精矿回收锌.在理论分析的基础上,考察了熔炼温度、纯碱用量、氧化锌和焦粉用量对金属铅回收率及固硫率的影响.结果表明,在880℃、纯碱与固体物的质量比为2.84、氧化锌用量为理论量的1.1倍、焦粉与胶泥的质量比为16%的优化条件下,铅直收率为96.64%,总回收率为98.06%,94.70%的元素硫被氧化锌固定.%A new green process of low-temperature,low discharge of carbon dioxide,no emission of sulfur oxide,clean and environment friendly smelting of secondary lead was proposed.In the process,with leadbearing secondary zinc oxide dusts as sulfur-fixing agent and coke powders as reducing agent,spent leadacid battery colloid sludge was reduced into crude lead and zinc was recovered as standard or marketable zinc sulfide concentrates in the molten salt of Na2CO3 at 800~900 ℃.The effects of smelting temperature,dosage of sodium carbonate,zinc oxide and coke powders on lead recovery and sulfur-fixing rate were investigated based on thermodynamic analysis.The results show that direct recovery and total recovery of lead is 96.64% and 98.06% respectively and sulfur-fixing rate is 94.70% under the optimum conditions including mass ratio of sodium carbonate and solid of 2.84,dosage of zinc oxide of 1.1 times of theoretical value,mass ratio of coke powders and colloid sludge of 16%,and temperature of 880 ℃.

  11. Influence of Smelting-Flue-Gas-Sulfuric Acid Purifying Process to Reagent Sulfuric Acid Preparation%冶炼烟气硫酸净化工艺对制取试剂硫酸的影响研究

    Institute of Scientific and Technical Information of China (English)

    张析; 余江鸿; 王进龙

    2014-01-01

    s:By using smelting-flue-gas sulfuric acid from a lead-zinc smelter as raw material to prepare reagent sulfuric acid through the process of direct distillation , it has heavy impact on quality of the reagent acid due to that lab test shows high content of impurities in the raw material acid .Therefore, raw material acid should be purified before distillatio , and experi-mental test is carried out to study raw material acid purifying process .Reagent sulfuric acid prepared from purified raw ma-terial acid meet the specifications for Chemically Pure under the National Standard GB /T625-2007.%利用某铅锌冶炼厂冶炼烟气硫酸为原料,经分析化验,原料酸中杂质含量较高,直接蒸馏对试剂硫酸的质量影响较大。因此,在蒸馏前需对原料酸进行净化处理,对原料酸的净化工艺进行了试验研究,采用经过净化的原料酸制取的试剂硫酸产品指标达到国家标准GB/T625-2007化学纯指标要求。

  12. 还原熔炼法从谦比希铜冶炼厂转炉渣中回收钴%Recovery of cobalt from converter slag of Chambishi Copper Smelter using reduction smelting process

    Institute of Scientific and Technical Information of China (English)

    翟秀静; 李乃军; 张旭; 符岩; 姜澜

    2011-01-01

    The reduction smelting process for cobalt recovery from converter slag of the Chambishi Copper Smelter in Zambia was studied.The effects of reducing agent dosage,smelting temperature and time and the addition of slag modifiers(CaO and TiO2)were investigated.In addition,the depleted slag and cobalt-beating alloy were characterized by X-ray diffraction,scanning electron microscopy and energy dispersive spectroscopy.Under the determined conditions,94.02% Co,95.76% Cu and less than 18% Fe in the converter slag were recovered.It was found that the main phases of depleted slag were fayalite and hercynite; and the cobalt-bearing alloy mainly contained metallic copper,Fe-Co-Cu alloys and a small amount of sulfide.%研究从赞比亚谦比希铜冶炼厂转炉渣中回收钴的还原熔炼过程.实验考察还原剂用量、熔炼温度、保温时间及渣型改善剂CaO和TiO2的添加对还原熔炼金属回收率的影响.采用X射线衍射、扫描电子显微镜及能谱分析对所得贫化渣和含钴合金进行表征.结果表明,在优化条件下,转炉渣中钴、铜、铁的回收率分别为94.02%,95.76%和小于18%;贫化渣的主要物相组成为铁橄榄石和铁尖晶石,含钴合金中主要含有金属铜、含钴铜的铁合金和少量的硫化物.

  13. Designing of Synergistic Waste Mixtures for Multiphase Reactive Smelting

    Directory of Open Access Journals (Sweden)

    Vaso Manojlović

    2016-06-01

    Full Text Available Electric arc furnace (EAF dust, together with a mill scale and coke were smelted in a laboratory electric arc furnace. These metallurgical wastes consist of a many different phases and elements, making the reaction process complex. Thermo-chemical analysis of the reactions in metal, slag, and gas phases was done, and used for modeling of the mixture composition and energy consumption required for smelting. Modelling was performed with the software named RikiAlC. The crude ZnO, slag, and metal phase were analyzed using the atomic absorption spectrometry (AAS, the optical emission spectrometry with inductively coupled plasma (ICP-OES, the X-ray diffraction (XRD, the scanning electron microscopy (SEM equipped with energy dispersive spectrometry (EDS, and reflected and transmitted light microscopy. Also, in order to follow the behavior of this process the exhausted gases were monitored. The synergetic effects of the designed mixture may be recognized in minimizing energy consumption for the smelting process, improving the product yield efficiency, and reducing the negative environmental effects.

  14. Final Report: Wetted Cathodes for Low-Temperature Aluminum Smelting

    Energy Technology Data Exchange (ETDEWEB)

    Brown, Craig W

    2002-09-30

    A low-temperature aluminum smelting process being developed differs from the Hall-Heroult process in several significant ways. The low-temperature process employs a more acidic electrolyte than cryolite, an alumina slurry, oxygen-generating metal anodes, and vertically suspended electrodes. Wetted and drained vertical cathodes are crucial to the new process. Such cathodes represent a significant portion of the capital costs projected for the new technology. Although studies exist of wetted cathode technology with Hall-Heoult cells, the differences make such a study desirable with the new process.

  15. Evaluation of Flash Bainite in 4130 Steel

    Science.gov (United States)

    2011-07-01

    Technical Report ARWSB-TR-11011 Evaluation of Flash Bainite in 4130 Steel G. Vigilante M. Hespos S. Bartolucci...4. TITLE AND SUBTITLE Evaluation of Flash Bainite in 4130 Steel 5a. CONTRACT NUMBER 5b. GRANT NUMBER 5c. PROGRAM ELEMENT...STATEMENT 13. SUPPLEMENTARY NOTES 14. ABSTRACT ARDEC independently evaluated a Flash Bainite process developed by Gary Cola, Jr., Sirius Protection

  16. Investigating the role of geology in the hydrological response of Mediterranean catchments prone to flash-floods: Regional modelling study and process understanding

    Science.gov (United States)

    Vannier, Olivier; Anquetin, Sandrine; Braud, Isabelle

    2016-10-01

    In this study, a regional distributed hydrological model is used to perform long-term and flash-flood event simulations, over the Cévennes-Vivarais region (south of France). The objective is to improve our understanding on the role played by geology on the hydrological processes of catchments during two past flash-flood events. This modelling work is based on Vannier et al. ("Regional estimation of catchment-scale soil properties by means of streamflow recession analysis for use in distributed hydrological models", Hydrological Processes, 2014), where streamflow recessions are analysed to estimate the thickness and hydraulic conductivity of weathered rock layers, depending on the geological nature of catchments. Weathered rock layers are thus implemented into the hydrological model CVN-p, and the contribution of these layers is assessed during flash-flood events simulations as well as during inter-event periods. The model is used without any calibration, to test hypotheses on the active hydrological processes. The results point out two different hydrological behaviours, depending on the geology: on crystalline rocks (granite and gneiss), the addition of a weathered rock layer considerably improves the simulated discharges, during flash-flood events as well as during recession periods, and makes the model able to remarkably reproduce the observed streamflow dynamics. For other geologies (schists especially), the benefits are real, but not sufficient to properly simulate the observed streamflow dynamics. These results probably underline the existence of poorly known processes (flow paths, non-linear spilling process) associated with the planar structure of schisty rocks. On a methodological point of view, this study proposes a simple way to account for the additional storage associated with each geological entity, through the addition of a weathered porous rock layer situated below the traditionally-considered upper soil horizons, and shows its applicability and

  17. Geomorphological factors of flash floods

    Science.gov (United States)

    Kuznetsova, Yulia

    2016-04-01

    Growing anthropogenic load, rise of extreme meteorological events frequency and total precipitation depth often lead to increasing danger of catastrophic fluvial processes worldwide. Flash floods are one of the most dangerous and less understood types of them. Difficulties of their study are mainly related to short duration of single events, remoteness and hard access to origin areas. Most detailed researches of flash floods focus on hydrological parameters of the flow itself and its meteorological factors. At the same time, importance of the basin geological and geomorphological structure for flash floods generation and the role they play in global sediment redistribution is yet poorly understood. However, understanding and quantitative assessment of these features is a real basis for a complete concept of factors, characteristics and dynamics of flash floods. This work is a review of published data on flash floods, and focuses on the geomorphological factors of the phenomenon. We consider both individual roles and interactions between different geomorphological features (the whole basin parameters, characteristics of the single slopes and valley bottom). Special attention is paid to critical values of certain factors. This approach also highlights the gaps or less studied factors of flash floods. Finally, all data is organized into a complex diagram that may be used for flash floods modeling. This also may help to reach a new level of flash flood predictions and risk assessment.

  18. Document Flash Thermography

    OpenAIRE

    Larsen, Cory; Baker, Doran

    2011-01-01

    This paper presents an extension of flash thermography techniques to the analysis of documents. Motivation for this research is to develop the ability to reveal covered writings in archaeological artifacts such as the Codex Selden or Egyptian Cartonnage. An emphasis is placed on evaluating several common existing signal processing techniques for their effectiveness in enhancing subsurface writings found within a set of test documents. These processing techniques include: contrast stretching, ...

  19. On multiphase negative flash for ideal solutions

    DEFF Research Database (Denmark)

    Yan, Wei; Stenby, Erling Halfdan

    2012-01-01

    coefficients. It is shown that this inner loop, named here as multiphase negative flash for ideal solutions, can be solved either by Michelsen's algorithm for multiphase normal flash, or by its variation which uses F−1 phase amounts as independent variables. In either case, the resulting algorithm is actually...... simpler than the corresponding normal flash algorithm. Unlike normal flash, multiphase negative flash for ideal solutions can diverge if the feasible domain for phase amounts is not closed. This can be judged readily during the iteration process. The algorithm can also be extended to the partial negative...

  20. A process concept for the production of benzene-ethylene-SNG from coal using flash hydropyrolysis technology

    Science.gov (United States)

    Greene, M. I.; Ladelfa, C. J.; Bivacca, S. J.

    1980-05-01

    Flash hydropyrolysis (FHP) of coal is an emerging technology for the direct production of methane, ethane and BTX in a single-stage, high throughput reactor. The FHP technique involves the short residence time (1-2 seconds), rapid heatup of coal in a dilute-phase, transport reactor. When integrated into an overall, grass-roots conversion complex, the FHP technique can be utilized to generate a product consisting of SNG, ethylene/propylene, benzene and Fischer-Tropsch-based alcohols. This paper summarizes the process engineering and economics of conceptualized facility based on an FHP reactor operation with a lignitic coal. The plant is hypothetically sited near the extensive lignite fields located in the Texas region of the United States. Utilizing utility-financing methods for the costing of SNG, and selling the chemicals cogenerated at petrochemical market prices, the 20-year average SNG cost has been computed to vary between $3-4/MM Btu, depending upon the coal costs, interest rates, debt/equity ratio, coproduct chemicals prices, etc.

  1. Optimization for Dwarf Banana with Microwave Low Temperature Carbon Dioxide Flash Puffing Process by Response Surface Methodology and Factor Analysis

    Directory of Open Access Journals (Sweden)

    Li Bao-Yu

    2016-01-01

    Full Text Available A three factors quadratic regression rotation combination design was adopted to optimize the technical conditions of microwave low temperature carbon dioxide flash puffing (MLTCDFP process for dwarf banana in the single factor’s foundation. This paper analyzed the effect of puffing temperature, puffing pressure, vacuum drying temperature and the interaction of the three factors on color, crispness, and the effect of hardness and water content. Based on the experimental data, the quadratic regression model of four indexes was deduced, then variables were analyzed with response surface methodology (RSM. The weights of four evaluation indexes was determined by factor analysis. The regression square was obtained by the comprehensive score as follow: Y=0.955+0.109X1+0.16X3−0.09X12+0.015X22 −0.15X32−0.018X1X2−0.056X1X3+0.016X2X3(R2=0.837.Through factor analysis, the range of the optimal technical conditions of MLTCDFP for dwarf banana obtained. The result indicated the four indexes were affected significantly by the puffing temperature and vacuum drying temperature, and the interactions of the three factors did not affect the product obviously. The optimal technical parameters were as follows: puffing temperature 91~95°C, puffing pressure 0.11~0.19MPa, vacuum temperature 81~85°C.

  2. The Role of Cleaner-Production in Ensuring a Cleaner Processing and Mining Environment in a Developing African Country. Case of a Midlands Steel Smelting Plant in Zimbabwe

    Directory of Open Access Journals (Sweden)

    Simon Chinguwa

    2012-08-01

    Full Text Available Mines and Mineral Processing Plants are major contributors to high dust emission. This paper explores Cleaner Production Opportunities, to ensure lower risk of dust explosion, minimum health & safety risks, reduction in environmental issues, operations closer to urban areas, reduction in maintenance and cleaning costs, minimum product shrinkage, load trucks and rail cars faster and to load stockpiles cleanly. The green methods will involve a walk through processing plant and identifying cleaner production opportunities. Characterisation of dust was also done. Dust Control Methods are going to be reviewed with the aim of minimizing dust-raising, containing it, suppressing it or extracting and collecting the dust eventually. The paper will also design and recommend specific methods of dust reduction for specific operations.

  3. 冶炼废水处理污泥中金的浸出过程动力学%Kinetics of leaching gold from processed sludge of nonferrous metal smelting waste water

    Institute of Scientific and Technical Information of China (English)

    李文婕; 陈云; 余训民; 李庆新; 关洪亮

    2012-01-01

    有色冶炼废水处理污泥中含有7.70g/t的金和90.30g/t的银,从污泥中提取金、银等有价金属,不仅可以减小污泥对环境的危害,还能较好地避免资源浪费.以硫氰酸铵为浸出剂对除砷后的二次污泥进行了浸金研究,并采用未反应核收缩模型对浸金过程的表观动力学进行了探讨,通过尝试法确定了浸出过程的控制步骤.结果表明,搅拌强度为250r/min时,该浸出过程受固体产物层扩散控制,其动力学方程为1-2η/3-(1-η)2/3=kυt,反应扩散系数为D′=10.807exp(-9855/RT),cm5.3594mol-1.1198s-1,表观活化能为9.855kJ/mol.%Processed sluge from nonferrous metal smelting waste water contains gold 7. 70 g/t and silver 90.30 g/t. Extraction of valuable metals such as gold and silver from the sludge can not only reduce the hazards of sludge on the environment, but also avoid wasting resources effectively. Ammonium thiocyanate was used as leaching reagent for extracting gold from the arsenic-free anode sludge (secondary sludge). The apparent kinetics of the gold leaching process was discussed by adopting the unreacted core contracting model and the controlling steps of the leaching process were confirmed by tentative method. The results show that the leaching process is under the diffusion control of solid product layer while the stirring intensity is 250 r/min,the kinetics equation, the diffusion coefficient and the apparent activation energy are 1-2η/3-(1-η)2/3=kυt, D′=10.807exp(-9855/RT),cm5.3594mol-1.1198s-1and 9.855kJ/mol, respectively.

  4. Bulk Ultrafine-Grained Interstitial-Free Steel Processed by Equal-Channel Angular Pressing Followed by Flash Annealing

    Science.gov (United States)

    Verma, Deepa; Pandey, Shobhit A.; Bansal, Anushka; Upadhyay, Shwetank; Mukhopadhyay, N. K.; Sastry, G. V. S.; Manna, R.

    2016-12-01

    Interstitial-free steel workpieces are deformed by equal-channel angular pressing (ECAP) for equivalent strain ɛvm = 3 and ɛvm = 21 followed by flash annealing. Microstructures are analyzed by optical microscopy, scanning electron microscopy and transmission electron microscopy. Mechanical properties are evaluated by hardness testing. Yield strength of materials is calculated from hardness values. Flash annealing (at 675 °C) of ECAPed samples for ɛvm = 3 and ɛvm = 21 results in abnormal subgrain growth and abnormal grain growth, respectively. Flash annealing at 700 °C of ECAPed (at ɛvm = 3) IF steel converts abnormally grown subgrains to grains which serve as nuclei for recrystallization and that result in bimodal grain size distribution. Bimodal grain size distribution is also produced when ECAPed IF steel for ɛvm = 21 is flash annealed at 675 °C due to abnormal grain growth or secondary recrystallization. Flash annealing of IF steel samples ECAPed for low ɛvm, in the temperature range 600-675 °C, decreases the hardness continuously with increase in the annealing temperature but it increases at high ɛvm. The former is due to annihilation of defects but the later is caused by ordering of nonequilibrium boundaries. The hardening and strengthening behaviors are similar.

  5. Visual sensitivity is a stronger determinant of illusory processes than auditory cue parameters in the sound-induced flash illusion.

    Science.gov (United States)

    Kumpik, Daniel P; Roberts, Helen E; King, Andrew J; Bizley, Jennifer K

    2014-06-24

    The sound-induced flash illusion (SIFI) is a multisensory perceptual phenomenon in which the number of brief visual stimuli perceived by an observer is influenced by the number of concurrently presented sounds. While the strength of this illusion has been shown to be modulated by the temporal congruence of the stimuli from each modality, there is conflicting evidence regarding its dependence upon their spatial congruence. We addressed this question by examining SIFIs under conditions in which the spatial reliability of the visual stimuli was degraded and different sound localization cues were presented using either free-field or closed-field stimulation. The likelihood of reporting a SIFI varied with the spatial cue composition of the auditory stimulus and was highest when binaural cues were presented over headphones. SIFIs were more common for small flashes than for large flashes, and for small flashes at peripheral locations, subjects experienced a greater number of illusory fusion events than fission events. However, the SIFI was not dependent on the spatial proximity of the audiovisual stimuli, but was instead determined primarily by differences in subjects' underlying sensitivity across the visual field to the number of flashes presented. Our findings indicate that the influence of auditory stimulation on visual numerosity judgments can occur independently of the spatial relationship between the stimuli. © 2014 ARVO.

  6. The DCRS: Dynamic compaction resistance sintering. A flash sintering process with a dynamic loading ability

    Science.gov (United States)

    Acquier, P.; Lemonnier, S.; Barraud, E.; Rusinek, A.; Grosdidier, T.; Allain-Bonnasso, N.; Terner, C.

    2012-08-01

    A homemade powder processing device combining Joule heating and dynamic compaction is presented. This device has been tested at temperatures as high as 1850 ∘C with heating rates up to 1000 ∘C/min. A detailed description of this device is given here followed by mechanical response and thermal validation tests. This highlights the reproducibility of the results on both the thermal and mechanical point of view.

  7. The DCRS: Dynamic compaction resistance sintering. A flash sintering process with a dynamic loading ability

    Directory of Open Access Journals (Sweden)

    Allain-Bonnasso N.

    2012-08-01

    Full Text Available A homemade powder processing device combining Joule heating and dynamic compaction is presented. This device has been tested at temperatures as high as 1850 ∘C with heating rates up to 1000 ∘C/min. A detailed description of this device is given here followed by mechanical response and thermal validation tests. This highlights the reproducibility of the results on both the thermal and mechanical point of view.

  8. Influence Of Temperature On The Rate Of Copper Recovery From The Slag Of The Flash Direct-To-Blister Process By A Solid Carbon Reducer

    Directory of Open Access Journals (Sweden)

    Madej P.

    2015-09-01

    Full Text Available The aim of the work was to investigate the influence of temperature on the rate of copper removal from the obtained slag from the flash direct-to-blister process by means of a carbon reducer. The slag used in this work was taken from the direct-to-blister Outokumpu flash furnace at the smelter in Głogów, and graphite penetrators were used as the slag reducers. The experiment was carried out at 1573 K, 1623 K and 1673 K. It was found that the rate of the de-coppering process of the “Głogów” slag increased with the increase of temperature.

  9. A Flash-ADC data acquisition system developed for a drift chamber array and a digital filter algorithm for signal processing

    Science.gov (United States)

    Yi, Han; Lü, Li-Ming; Zhang, Zhao; Cheng, Wen-Jing; Ji, Wei; Huang, Yan; Zhang, Yan; Li, Hong-Jie; Cui, Yin-Ping; Lin, Ming; Wang, Yi-Jie; Duan, Li-Min; Hu, Rong-Jiang; Xiao, Zhi-Gang

    2016-11-01

    A Flash-ADC data acquisition (DAQ) system has been developed for the drift chamber array designed for the External-Target-Experiment at the Cooling Storage Ring at the Heavy Ion Research Facility, Lanzhou. The simplified readout electronics system has been developed using the Flash-ADC modules and the whole waveform in the sampling window is obtained, with which the time and energy information can be deduced with an offline processing. A digital filter algorithm has been developed to discriminate the noise and the useful signal. With the digital filtering process, the signal to noise ratio (SNR) is increased and a better time and energy resolution can be obtained. Supported by National Basic Research Program of China (973) (2015CB856903 and 2014CB845405), partly by National Science Foundation of China (U1332207 and 11375094), and by Tsinghua University Initiative Scientific Research Program

  10. Flash thermal conditioning of olive pastes during the olive oil mechanical extraction process: impact on the structural modifications of pastes and oil quality.

    Science.gov (United States)

    Esposto, Sonia; Veneziani, Gianluca; Taticchi, Agnese; Selvaggini, Roberto; Urbani, Stefania; Di Maio, Ilona; Sordini, Beatrice; Minnocci, Antonio; Sebastiani, Luca; Servili, Maurizio

    2013-05-22

    The quality of virgin olive oil (VOO) is strictly related to the concentrations of phenolic and volatile compounds, which are strongly affected by the operative conditions of the VOO mechanical extraction process. The aim of this work is to study the impact of a new technology such as flash thermal conditioning (FTC) on olive paste structural modification and on VOO quality. The evaluation of olive paste structure modification by cryo-scanning electron microscopy (cryo-SEM) showed that the application of FTC after crushing produces significant differences in terms of the breaking of the parenchyma cells and aggregation of oil droplets in comparison to the crushed pastes. The virgin olive oil flash thermal conditioning (VOO-FTC) featured a higher concentration of volatile compounds compared to that in the control, particularly of all saturated and unsaturated aldehydes and esters, whereas the phenolic concentration was higher in VOO obtained from the traditional process (VOO-C).

  11. Jinde Lead lead smelting project starts construction

    Institute of Scientific and Technical Information of China (English)

    2008-01-01

    <正>On Dec.20,the lead smelting project of Jiangxi Jinde Lead started construction in Dexin as a technical renovation project on environmental treatment of Jiangxi Metallurgical Group.The project is the one with the largest investment of Provincial Metallurgical Group in non-ferrous

  12. Evaluation of the Rockwell International flash-hydroliquefaction process. Final summary report

    Energy Technology Data Exchange (ETDEWEB)

    Sirohi, V.P.

    1980-09-01

    At the request of the Department of Energy, UOP/SDC has evaluated the Rockwell Hydroliquefaction Process to determine the adequacy of the existing PDU data base and to assess the practicability and operability of the process. UOP/SDC conducted nine studies. Their findings follow: (1) A complete designed set of experiments must be run on the present PDU to make possible satisfactory analysis of the effects of variables especially the effect of diluents in the H/sub 2/ feed and the possibility of carbon deposition problems. (2) Basic improvements in the equipment and operation of the PDU should first be made (Ten specific recommendations are made). (3) A reactor design concept must be developed that looks feasible for design, fabrication, and operation. (4) A conceptual commercial design and economics should be prepared based on a realistic set of design bases and criteria. (5) If the above are accomplished successfully with attractive results, then and only then: (a) A study should be made of the refining requirements of the product, which are expected to be expensive based on the H/C ratio. (b) The PDU should be modified for continuous runs of up to one month to: Confirm the data correlations, estimate the reliability of the reactor and process, adhere to the requirements stated above, test cryogenic gas separation, study fouling and erosion, study lockhopper feeding, establish initial reliability of the coal injector and precombustion assembly head, collect scale-up and design data, and conduct a materials study and confirm materials choices. (c) Determine particle size of the char and of the solids in the oil product, the degree to which they may be separated, and how the ash should be removed from the product oil.

  13. 低合金钢冶炼过程增氮行为分析%Behavior Analysis of Nitrogen Content Increasing in Low Alloy Steel Smelting Process

    Institute of Scientific and Technical Information of China (English)

    张帆; 范植金; 丁礼权

    2014-01-01

    为提高中厚板系列低合金钢氮含量控制水平,从热力学、动力学角度全面分析冶炼过程增氮行为,并结合相关试验对影响钢液增氮的因素进行分析。结果表明,氮在钢液中的溶解度与温度、氮分压以及合金成分有关;气泡—钢液面上的吸附化学反应为限制性环节;当钢液中w(O)≥0.04%或w(S)≥0.06%,钢液吸氮基本停止;当转炉全程底吹氮强度不超过0.025 m3/(min·t)时,转炉终点氮含量可控制在10×10-6以内。%In order to improve the level of nitrogen content control of low alloy steel, the paper analyzed the behavior of nitrogen content increasing from the perspective of thermodynamics and kinetics, and illustrated the factors with related experiment. The results show that, the nitrogen solubility in liquid steel relate to temperature, nitrogen partial pressure and alloy composition;bubbles-liquid steel surface chemical reaction is restrictive link; when w(O) ≥0.04% or w(S) ≥0.06% , the increasing nitrogen process of liquid steel stopped; when the whole strength of bottom blowing nitrogen of BOF is no more than 0.025 m3/(min·t), nitrogen content of converter can be controlled within 10×10-6.

  14. Shining a light on oil sands production : spectroscopy could bring flash of insight to ore processing

    Energy Technology Data Exchange (ETDEWEB)

    Zlotnikov, D.

    2010-09-15

    Oil sands are a mixture of silts, sands and clay, and the variability poses challenges to surface mine operators. A professor of Earth and Atmospheric Sciences at the University of Alberta has been working on a spectroscopy project to provide the oil sand industry with real-time ore composition and particle size readings from the mine face. These can then be used to adjust processing conditions at the extraction plant or froth treatment facility, ensuring optimal recovery levels and smooth operation. Developing a spectrographic fingerprint of an ore sample involves shining a very narrow wavelength of light at the sample, recording the intensity of reflected light and repeating the process across a range of wavelengths. The challenges of putting the spectroscopic equipment at the mine site were described. The project is 1 of the more than 20 projects currently at the Centre for Oil Sands Innovation (COSI), a partnership between Imperial Oil and the University of Alberta. Imperial contributed $10 million in funding over the following 5 years, with the governments of Alberta and Canada contributing additional funds. Imperial Oil is not the only beneficiary of COSI research, as all work that comes out of COSI is ultimately published. 1 fig.

  15. 基于蝴蝶突变离子型稀土冶炼分离过程危险性分析%Hazard analysis of ion-adsorption rare earth ’s smelting and separation processes based on butterfly catastrophe

    Institute of Scientific and Technical Information of China (English)

    林大建; 叶慧琳

    2013-01-01

    Acid digestion, extraction, sedimentation, burning etc. are included in the ion-type rare earth sepa-ration and production processes. Characteristics of the hazardous substances used in smelting and separation process and dangers that are poisoning, burning, mechanical injuries in the production process are analyzed. The fire resistance rating of extraction workshop is low and fire prevention zone does not meet the safety re-quirements. Analyzing the dangerous and harmful factors in production process and using butterfly catastrophe theory to establish the ion-type rare earth smelting separation enterprise safety production guarantee system and the degree of risk definition and classification model of mutation series is of great significance to the en-terprise management and production of rare earth smelting separation.%离子型稀土冶炼分离生产工艺流程包含:酸溶、萃取、沉淀、灼烧等,研究分析稀土冶炼分离过程中使用的危险物质的特点,指出生产工艺中存在中毒、灼烧、机械伤害等危险性以及萃取厂房的耐火等级偏低,防火分区不符合安全要求等问题。分析生产过程中存在的危险有害因素,利用蝴蝶型突变理论,建立离子型稀土冶炼分离企业的安全生产保障体系、危险程度界定和突变级数分级模型,对稀土冶炼分离企业管理和生产具有深远的现实意义。

  16. Flash sintering of ceramic materials

    OpenAIRE

    Dancer, C. E. J.

    2016-01-01

    During flash sintering, ceramic materials can sinter to high density in a matter of seconds while subjected to electric field and elevated temperature. This process, which occurs at lower furnace temperatures and in shorter times than both conventional ceramic sintering and field-assisted methods such as spark plasma sintering, has the potential to radically reduce the power consumption required for the densification of ceramic materials. This paper reviews the experimental work on flash sint...

  17. Evaluation of the cryogenic helium recovery process from natural gas based on flash separation by advanced exergy cost method - Linde modified process

    Science.gov (United States)

    Ansarinasab, Hojat; Mehrpooya, Mehdi; Parivazh, Mohammad Mehdi

    2017-10-01

    In this paper, exergy cost analysis method is used to evaluate a new cryogenic Helium recovery process from natural gas based on flash separation. Also advanced exergoeconomic analysis was made to determine the amount of avoidable exergy destruction cost of the process component. This proposed process can extract Helium from a feed gas stream with better efficiency than other existing processes. The results indicate that according to the avoidable endogenous exergy destruction cost C-4 (287.2/hr), C-5 (257.3/hr) and C-6 (181.6/hr) compressors should be modified first, respectively. According to the endogenous investment and exergy destruction cost, the interactions between the process components are not strong. In compressors, a high proportion of the cost of exergy destruction is avoidable while in these components, investment costs are unavoidable. In heat exchangers and air coolers, a high proportion of the exergy destruction cost is unavoidable while in these components, investment costs are avoidable. Finally, three different strategies are suggested to improve performance of each component, and the sensitivity of exergoeconomic factor and cost of exergy destruction to operating variables of the process are studied.

  18. Flash Thermal Conditioning of Olive Pastes during the Oil Mechanical Extraction Process: Cultivar Impact on the Phenolic and Volatile Composition of Virgin Olive Oil.

    Science.gov (United States)

    Veneziani, Gianluca; Esposto, Sonia; Taticchi, Agnese; Selvaggini, Roberto; Urbani, Stefania; Di Maio, Ilona; Sordini, Beatrice; Servili, Maurizio

    2015-07-08

    The concentration of phenolic and volatile compounds in virgin olive oil (VOO) is closely related to the different operative conditions applied to the mechanical extraction process of the olive oil. However, the great qualitative and quantitative variability of these compounds indicates an important role played by genetic and agronomic aspects. A heat exchanger was placed in front of a traditional, covered malaxer to study the impact of flash thermal conditioning (FTC) of olive paste on the quality of VOO, which is highly influenced by phenolic release and aroma generation. The VOO flash thermal conditioning of five major Italian cultivars showed a higher concentration of phenols (range of increase percentage, 9.9-37.3%) compared to the control trials, whereas the FTC treatment featured a differentiated impact on the volatile fractions, associated with the genetic origins of the olives.

  19. 改进硫脲法浸出含硫铁矿炼锌渣中银的工艺%Leaching process of silver from zinc-smelting slag of sulfur-bearing pyrite by modified thiourea method

    Institute of Scientific and Technical Information of China (English)

    张玉; 苏静; 龙云飞; 吕小艳; 文衍宣

    2013-01-01

    采用硫脲为络合剂、双氧水为氧化剂,研究了在硝酸介质中浸出含硫铁矿炼锌渣中银的工艺.考察了搅拌速率、反应时间、反应温度、硝酸初始浓度、双氧水浓度、硫脲浓度等因素对银浸出率的影响.结果表明,银的浸出率随着搅拌速率的增大和反应时间的延长先增大然后保持不变,随反应温度、硫脲浓度、双氧水浓度和硝酸初始浓度的增加先增大后减小.当搅拌速率为200 r/min、硝酸浓度为4.11 mol/L、双氧水浓度为0.82 mol/L、硫脲浓度为3.25 mol/L、反应温度为50℃、反应时间为lh时,银浸出率可达82.0%.%The leaching process of silver from zinc-smelting slag of sulfur-bearing pyrite with thiourea as chelating agent and H2O2 as oxidant in HNO3 was studied.The effects of stirring speed,reaction time,reaction temperature,HNO3 initial concentration,H2O2 concentration,and thiourea concentration etc.on the leaching efficiency of silver were investigated.Results showed that the leaching ratio of silver first increased and then kept constant with the increase of the stirring speed and the reaction time,while it first increased and then decreased with the increase of reaction temperature,HNO3 initial concentration,H2O2 concentration,and thiourea concentration.The optimal conditions for leaching of silver with thiourea were found as follows:the stirring speed was 200 r/min,HNO3 initial concentration was 4.11 mol/L,H2O2 concentration was 0.82 mol/L,thiourea concentration was 3.25 mol/L,reaction temperature was 50 ℃,and reaction time was 1.0 h.Under these conditions,the leaching ratio of silver was up to 82.0%.

  20. 一种稀有金属冶炼伴生放射性元素的去除方法%Removing Radioactive Elements Associated with Rare Metals in the Smelting Process

    Institute of Scientific and Technical Information of China (English)

    张选旭; 张洁

    2015-01-01

    Remove radioactive elements in smelting processes can ensure product quality and reduce environmental impact due to the associated radioactive elements with rare metal ores. This paper studied the two-step removal technology of radioactive thorium, uranium associated with ion adsorption rare earth by organic extraction. Parts of the radioactive elements were concentrated in the acid residue by acid decomposition with removal rate reaching 80%~90%;the remaining was removed by precipitating thorium, uranium in the waste water with removal rate reaching 8%~18 %. Testing results showed that thorium, uranium contents in wastewater discharge were lower than 0.1 mg/L, conforming with the limit requirements in the relevant rare earth industry emission standards. The removed radioactive materials were stockpiled, avoiding the radioactive contamination of the environment.%由于稀有金属矿物中往往伴生放射性元素,因此冶炼工艺中去除放射性元素具有保证产品质量和减少环境影响的双重意义。研究针对离子型稀土冶炼工艺去除放射性元素这一课题,提出了一种湿法冶金工艺中通过有机萃取去除稀有金属冶炼伴生放射性元素钍、铀的方法;该方法为两步去除法,即通过酸分解将一部分放射性元素富集在酸溶渣中,该工序去除率达到80%~90%,剩余部分通过有机萃取进行去除,采用中和法将废水中放射性元素钍、铀沉淀下来,去除率达到8%~18%;经测定,排放的废水中钍、铀含量小于0.1 mg/L,符合稀土工业污染物排放标准相关限值要求;去除的放射性物质集中堆存于低放库中,避免了放射性元素对环境的污染。此工艺可为其他稀有金属矿种冶炼去除钍、铀提供借鉴。

  1. The Synoptic Model of Widespread Extensive Flash-Flood-Producing Rainstorm Processes in Guangxi%广西大范围致洪暴雨天气模型

    Institute of Scientific and Technical Information of China (English)

    黄香杏; 林开平; 赵江洁

    2001-01-01

    Based on the analysis of spatial and temporal distribution on the flash-flood-producing rainstorm and the features of affecting synoptic systems, the synoptic model of widespread extensive flash-flood-producing rainstorm processes was established and divided into three types, as well. The feature of circle situation and favorable conditions that probably caused the flash-flood-producing rainstorm were given in each type. As a result, the synoptic systems will be useful in forecasting the torrential rainfall processes in the future.%通过致洪暴雨时空分布特点和相应影响天气系统特征的分析,将广西大范围致洪暴雨天气模型分为3个类型,提出各类模型的环流特征、入型条件和致洪暴雨产生的有利条件,为今后制作致洪暴雨预报作出新的尝试。

  2. Notes from the Field: Acute Mercury Poisoning After Home Gold and Silver Smelting--Iowa, 2014.

    Science.gov (United States)

    Koirala, Samir; Leinenkugel, Kathy

    2015-12-18

    In March 2014, a man, aged 59 years, who lived alone and had been using different smelting techniques viewed on the Internet to recover gold and silver from computer components, was evaluated at a local emergency department for shortness of breath, tremors, anorexia, and generalized weakness. During the smelting processes, he had used hydrogen peroxide, nitric acid, muriatic acid, and sulfuric acid purchased from local stores or Internet retailers. For protection, he wore a military gas mask of unknown type. The mask was used with filter cartridges, but their effectiveness against chemical fumes was not known.

  3. Using Artificial Soil and Dry-Column Flash Chromatography to Simulate Organic Substance Leaching Process: A Colorful Environmental Chemistry Experiment

    Science.gov (United States)

    de Avellar, Isa G. J.; Cotta, Tais A. P. G.; Neder, Amarilis de V. Finageiv

    2012-01-01

    Soil is an important and complex environmental compartment and soil contamination contributes to the pollution of aquifers and other water basins. A simple and low-cost experiment is described in which the mobility of three organic compounds in an artificial soil is examined using dry-column flash chromatography. The compounds were applied on top…

  4. Flash Sintering of Alumina-based Ceramics

    OpenAIRE

    Biesuz, Mattia

    2017-01-01

    Flash sintering is an electrical field-assisted consolidation technology and represents a very novel technique for producing ceramic materials, which allows to decrease sensibly both processing temperature and time. Starting from 2010, when flash sintering was discovered, different ceramic materials with a wide range of electrical properties have been successfully densified. Up to date, the research on flash sintering has been mainly focused on ionic and electronic conductors and on semicondu...

  5. Flash calcination of kaolinite rich clay and impact of process conditions on the quality of the calcines: A way to reduce CO2 footprint from cement industry

    DEFF Research Database (Denmark)

    Gebremariam, Abraham Teklay; Yin, Chungen; Rosendahl, Lasse

    2016-01-01

    deplete metakaolin into unwanted products (e.g., mullite), which limits the use of the calcines as a supplementary cementitious material. With this regard, a dynamic model of flash calcination of kaolinite rich clay particles is developed using gPROMS (general PROcess Modeling System) to predict...... suspension calciner. The model is validated by the experimental data (e.g., the degree of dehydroxylation and the density of the calcines). Based on the model, the impacts of process conditions and feed properties on the quality of the calcination products are thoroughly examined....

  6. Modelación del proceso de calcinación flash durante la activación de arcillas // Modeling of the flash calcination process during clay activation

    Directory of Open Access Journals (Sweden)

    Rubén Borrajo‐Pérez

    2012-01-01

    Full Text Available La activación térmica ha sido usada para producir puzolanas con elevada reactividad, manifestada en losprimeros días de curado y como sustitutas del clinker. La temperatura es un parámetro de control en laactivación y se debe considerar cuál es su valor para cada materia prima. Considerando los precios delmercado mundial, nuevas materias primas para producir puzolanas se investigan continuamente. Esteartículo trata la modelación física de los procesos térmico, hidrodinámico y de dehidroxilación queexperimentan las partículas expuestas a una corriente gaseosa. El objetivo es modelar la calcinaciónutilizando un modelo físico y discutirlo. La velocidad, temperatura y avance de la dehidroxilación de laspartículas se obtiene como función de los parámetros del gas portador y se incluyen las pérdidas de calor.El modelo, resuelto explícitamente, reproduce valores de la literatura y predice el tiempo de residenciapara que las partículas alcancen su total dehidroxilación dentro del calcinador.Palabras claves: puzolana, calcinación, flash, modelación.__________________________________________________________________AbstractPuzzolanic activity in some materials can be increased by means of different processes, among them,thermal activation is one of the most promising. In the last few years, thermal activation processes havebeen used to produce puzzolans with high reactivity in early ages of concrete. Temperature is an importantparameter in the activation process, and as a consequence, different temperatures are required for eachraw materials. Taking into account the high prices of Metakaolin, new puzzolanic materials are constantlyinvestigated. Other materials, with higher levels of kaolin are being used for activation with good results.This paper is about the modeling of thermal, hydrodynamics and dehydroxilation processes undergone byparticles exposed to a hot gas stream. The models employed are discussed; the velocity and

  7. 超低碳铝镇静钢冶炼过程氮含量的控制%Nitrogen control of ultra-low-carbon Al-killed steel in a smelting process

    Institute of Scientific and Technical Information of China (English)

    王敏; 张超杰; 蔡小峰; 张思源; 郭昭桥

    2016-01-01

    Based on the fact of high nitrogen pick-up, large nitrogen fluctuation and poor control in some steel works, the main aspects of nitrogen removal and nitrogen pick-up in an ultra-low-carbon Al-killed steel smelting process were summarized by analyzing the process data and sampling. The main sections for nitrogen removal are BOF decarburization period and vacuum treatment. High decarburization amount can lower the nitrogen content at the BOF endpoint. There is just a limited effect of switching between nitrogen and argon on the final nitrogen content at the BOF endpoint before the point of 70% oxygen blowing. Free oxygen is favorable for deni-trification by promoting the reaction of carbon and oxygen under the RH mode, in contrast under the VD mode. When free oxygen in liquid steel is controlled above 200 í10 -6 , the nitrogen absorption during tapping can be controlled within 5 í10 -6 . The nitrogen introduction of furnace charge is the important factor of nitrogen pick-up during the vacuum refining process, and it is up to 11í10 -6 . The minimum of nitrogen pick-up can reduce to 1í10 -6 by adopting gasket sealing and argon blowing protection simultaneously.%针对企业冶炼超低碳铝镇静钢过程中增氮量高、波动大及控制不稳定的问题,采用工艺数据统计和现场取样的手段,系统梳理了冶炼过程钢液脱氮和增氮的主要环节和影响因素.转炉脱碳期和真空处理是脱氮的主要环节,碳氧期的总脱碳量高则终点氮含量低;转炉底吹N2/Ar切换点在吹炼70%以前对终点氮含量影响不大;VD在无氧条件下脱氮有利,RH则在有氧条件下脱氮有利.控制钢中溶解氧>200×10-6则出钢过程增氮可控制在5×10-6以下;炉料的氮带入是真空精炼环节增氮的重要因素,最高达11×10-6;采用密封垫+吹Ar的保护方式,增氮量最低为1×10-6.

  8. SmeltCam: underwater video codend for trawled nets with an application to the distribution of the imperiled delta smelt.

    Directory of Open Access Journals (Sweden)

    Frederick Feyrer

    Full Text Available Studying rare and sensitive species is a challenge in conservation biology. The problem is exemplified by the case of the imperiled delta smelt Hypomesus transpacificus, a small delicate fish species endemic to the San Francisco Estuary, California. Persistent record-low levels of abundance and relatively high sensitivity to handling stress pose considerable challenges to studying delta smelt in the wild. To attempt to overcome these and other challenges we have developed the SmeltCam, an underwater video camera codend for trawled nets. The SmeltCam functions as an open-ended codend that automatically collects information on the number and species of fishes that pass freely through a trawled net without handling. We applied the SmeltCam to study the fine-scale distribution of juvenile delta smelt in the water column in the upper San Francisco Estuary. We learned that during flood tides delta smelt were relatively abundant throughout the water column and that during ebb tides delta smelt were significantly less abundant and occurred only in the lower half and sides of the water column. The results suggest that delta smelt manipulate their position in the water column to facilitate retention in favorable habitats. With the application of the SmeltCam we increased the survival of individual delta smelt by 72% compared to using a traditional codend, where all of the fish would have likely died due to handling stress. The SmeltCam improves upon similar previously developed silhouette photography or video recording devices and demonstrates how new technology can be developed to address important questions in conservation biology as well as lessen the negative effects associated with traditional sampling methods on imperiled species.

  9. 两种冶炼工艺对作业工人健康影响的比较%Comparison of Effects of 2 Types of Smelting Processes on Health of Exposed Workers

    Institute of Scientific and Technical Information of China (English)

    冯祖辉; 李兴中; 蔡永玲

    2009-01-01

    目的 探讨2种不同冶炼生产工艺下职业病有害因素对作业工人健康的影响.方法 采用原子吸收分光光度计石墨炉法对尿铅含量进行测定,运用t和χ2检验对结果进行统计分析.结果 传统工艺所测铅烟、二氧化硫浓度分别为(1.023±0.931)、(3.753±1.631)mg/m3,新工艺则分别为(0.308±0.166)、(1.227±0.903)mg/m3,传统工艺与新工艺所测铅烟、二氧化硫浓度差异均有统计学意义(P<0.05);在所调查的63个项目中有鼻干、腹痛、乏力、牙齿松动4项接触组明显高于对照组(P<0.01);职业健康检查中有贫血、慢性支气管炎、尿潜血、慢性鼻炎、慢性结膜炎、肝功能接触组明显高于对照组(P<0.05);2组炉前工的尿铅超标人数差异有统计学意义(P<0.01).结论 通过技术改造后车间铅烟、二氧化硫等职业病危害因素浓度明显下降,职业病危害因素对作业工人的健康影响有明显改善.%[Objective]To explore the effects of occupational hazards caused by 2 types of smelting processes on health of exposed workers.[Methods]Graphite furnace atomic absorption spectrometer was applied to measure lead content of urine,t test and χ2 test were used to analyze results statistically.[Results]Measured by traditional crafts, the content of lead and sulfur dioxide concentration was (1.023±0.931) mg/m3 and (3.753±1.631) mg/m3; (0.308±0.166) mg/m3 and (1.227±0.903) mg /m3 by new techniques, the differences were significant (P<0.05). In the occupational health examination, anemia, chronic bronchitis, urinary occult blood, chronic rhinitis, chronic conjunctivitis, liver function of exposed group was more serious than that of control group significantly (P<0.05); the difference of the number of workers with excessive urine lead between 2 groups was significant(P<0.01).[Conclusion]After technical reform, concentrations of occupational hazards such as lead smoke and sulfur dioxide decrease

  10. Flash sintering of ceramic materials

    Science.gov (United States)

    Dancer, C. E. J.

    2016-10-01

    During flash sintering, ceramic materials can sinter to high density in a matter of seconds while subjected to electric field and elevated temperature. This process, which occurs at lower furnace temperatures and in shorter times than both conventional ceramic sintering and field-assisted methods such as spark plasma sintering, has the potential to radically reduce the power consumption required for the densification of ceramic materials. This paper reviews the experimental work on flash sintering methods carried out to date, and compares the properties of the materials obtained to those produced by conventional sintering. The flash sintering process is described for oxides of zirconium, yttrium, aluminium, tin, zinc, and titanium; silicon and boron carbide, zirconium diboride, materials for solid oxide fuel applications, ferroelectric materials, and composite materials. While experimental observations have been made on a wide range of materials, understanding of the underlying mechanisms responsible for the onset and latter stages of flash sintering is still elusive. Elements of the proposed theories to explain the observed behaviour include extensive Joule heating throughout the material causing thermal runaway, arrested by the current limitation in the power supply, and the formation of defect avalanches which rapidly and dramatically increase the sample conductivity. Undoubtedly, the flash sintering process is affected by the electric field strength, furnace temperature and current density limit, but also by microstructural features such as the presence of second phase particles or dopants and the particle size in the starting material. While further experimental work and modelling is still required to attain a full understanding capable of predicting the success of the flash sintering process in different materials, the technique non-etheless holds great potential for exceptional control of the ceramic sintering process.

  11. Yunnan Smelting Group Examines an Aluminum Project for Possible Investment

    Institute of Scientific and Technical Information of China (English)

    2008-01-01

    <正>Tian Yong,General Manager of Yunnan Smelt- ing Group,has gone to Zha gai NuoEr in Heilongjiang Province with a study group to conduct a full careful examination on the feasi- bility of the investment in the aluminum pro- ject.Yunnan Smelting Group is a large-scale

  12. Da Xinganling Lead Zinc Smelting Base Commencing the Construction

    Institute of Scientific and Technical Information of China (English)

    2008-01-01

    <正>The construction of the first phase of 150,000- ton lead zinc smelting base project,the largest lead zinc smelting project in Heilongjiang Province,of Da Xinganling Yunye Mining Ltd. officially started on May 24 in Jiagedaqi Indus- trial Park in Da Xinganling Region.

  13. Polychlorinated dibenzo-p-dioxin and dibenzofuran and polychlorinated biphenyl emissions from different smelting stages in secondary copper metallurgy.

    Science.gov (United States)

    Hu, Jicheng; Zheng, Minghui; Nie, Zhiqiang; Liu, Wenbin; Liu, Guorui; Zhang, Bing; Xiao, Ke

    2013-01-01

    Secondary copper production has received much attention for its high emissions of polychlorinated dibenzo-p-dioxin and dibenzofuran (PCDD/F) reported in previous studies. These studies focused on the estimation of total PCDD/F and polychlorinated biphenyl (PCB) emissions from secondary copper smelters. However, large variations in PCDD/F and PCB emissions reported in these studies were not analyzed and discussed further. In this study, stack gas samples at different smelting stages (feeding-fusion, oxidation and deoxidization) were collected from four plants to investigate variations in PCDD/F and PCB emissions and characteristics during the secondary copper smelting process. The results indicate that PCDD/F emissions occur mainly at the feeding-fusion stage and these emissions contribute to 54-88% of the total emissions from the secondary copper smelting process. The variation in feed material and operating conditions at different smelting stages leads to the variation in PCDD/F emissions during the secondary copper smelting process. The total PCDD/F and PCB discharge (stack gas emission+fly ash discharge) is consistent with the copper scrap content in the raw material in the secondary copper smelters investigated. On a production basis of 1 ton copper, the total PCDD/F and dl-PCB discharge was 102, 24.8 and 5.88 μg TEQ t(-1) for the three plants that contained 100%, 30% and 0% copper scrap in their raw material feed, respectively.

  14. Quick Guide to Flash Catalyst

    CERN Document Server

    Elmansy, Rafiq

    2011-01-01

    How do you transform user interface designs created in Photoshop or Illustrator into interactive web pages? It's easier than you think. This guide shows you how to use Adobe Flash Catalyst to create interactive UIs and website wireframes for Rich Internet Applications-without writing a single line of code. Ideal for web designers, this book introduces Flash Catalyst basics with detailed step-by-step instructions and screenshots that illustrate every part of the process. You'll learn hands-on how to turn your static design or artwork into working user interfaces that can be implemented in Fla

  15. Characterization and Recovery of Valuables from Waste Copper Smelting Slag

    Science.gov (United States)

    Prince, Sarfo; Young, Jamie; Ma, Guojun; Young, Courtney

    Silicate slags produced from smelting copper concentrates contains valuables such as Cu and Fe as well as heavy metals such as Pb and As which are considered hazardous. In this paper, various slags were characterized with several techniques: SEM-MLA, XRD, TG-DTA and ICP-MS. A recovery process was developed to separate the valuables from the silicates thereby producing value-added products and simultaneously reducing environmental concerns. Results show that the major phases in air-cooled slag are fayalite and magnetite whereas the water-cooled slag is amorphous. Thermodynamic calculations and carbothermal reduction experiments indicate that most of Cu and Fe can be recovered from both types using minor amounts of lime and alumina and treating at 1350°C (1623K) or higher for 30 min. The secondary slag can be recycled to the glass and/or ceramic industries.

  16. Recovering indium with sulfating roasting from copper-smelting ash

    Institute of Scientific and Technical Information of China (English)

    2007-01-01

    A technology for recovering indium from Jinchuan copper-smelting ash was developed. Indium in the ash was first enriched to the leaching-slag in leaching process, and then recovered by sulfating roasting. The method included mixing the leaching-slag with sulfuric acid, making them into particles, roasting the mixture, and then leaching the calcine with hot water. Above 90% of indium in calcine could be dissolved into the leaching solution. The optimized conditions were determined as follows: the mass ratio of sulfuric acid to leaching slag was 0.1, the roasting time was about 1 to 1.5 h in the temperature range of 200-250 ℃, and the calcine was leached for 1 h with 5:1 of liquid/solid ratio at 60℃. Over 99% of indium in leaching solution was finally enriched by Zn substitution or sulfide precipitation.

  17. 依托工作过程的Flash动画教学主题构思%Conception of the Teaching Themes for Flash Animation Based on Working Process

    Institute of Scientific and Technical Information of China (English)

    刘志兰

    2013-01-01

    With the rapid development of computer application industry, animation and videos bring people visual impact, and they are playing a more and more important role in daily life, therefore, the design idea and technology attract more and more attention. In view of the design of Flash two dimensional anima-tion teaching, this paper, based on working process, mainly inter-prets some ideas on the teaching of Flash two dimensional ani-mation.%  随着计算机应用行业的快速发展,动画视频给人们带来的视觉冲击效果,在日常生活中的影响越来越强大,因此,动画的设计思想和制作技术越来越受到专门行业者的高度注视。本文针对Flash二维动画课程设计,在基于工作过程的教学方面,进行了改革试水,重点阐述了Flash二维动画教学思路的几点探索。

  18. Electrical wire explosion process of copper/silver hybrid nano-particle ink and its sintering via flash white light to achieve high electrical conductivity

    Science.gov (United States)

    Chung, Wan-Ho; Hwang, Yeon-Taek; Lee, Seung-Hyun; Kim, Hak-Sung

    2016-05-01

    In this work, combined silver/copper nanoparticles were fabricated by the electrical explosion of a metal wire. In this method, a high electrical current passes through the metal wire with a high voltage. Consequently, the metal wire evaporates and metal nanoparticles are formed. The diameters of the silver and copper nanoparticles were controlled by changing the voltage conditions. The fabricated silver and copper nano-inks were printed on a flexible polyimide (PI) substrate and sintered at room temperature via a flash light process, using a xenon lamp and varying the light energy. The microstructures of the sintered silver and copper films were observed using a scanning electron microscope (SEM) and a transmission electron microscope (TEM). To investigate the crystal phases of the flash-light-sintered silver and copper films, x-ray diffraction (XRD) was performed. The absorption wavelengths of the silver and copper nano-inks were measured using ultraviolet-visible spectroscopy (UV-vis). Furthermore, the resistivity of the sintered silver and copper films was measured using the four-point probe method and an alpha step. As a result, the fabricated Cu/Ag film shows a high electrical conductivity (4.06 μΩcm), which is comparable to the resistivity of bulk copper (1.68 μΩcm). In addition, the fabricated Cu/Ag nanoparticle film shows superior oxidation stability compared to the Cu nanoparticle film.

  19. Electrical wire explosion process of copper/silver hybrid nano-particle ink and its sintering via flash white light to achieve high electrical conductivity.

    Science.gov (United States)

    Chung, Wan-Ho; Hwang, Yeon-Taek; Lee, Seung-Hyun; Kim, Hak-Sung

    2016-05-20

    In this work, combined silver/copper nanoparticles were fabricated by the electrical explosion of a metal wire. In this method, a high electrical current passes through the metal wire with a high voltage. Consequently, the metal wire evaporates and metal nanoparticles are formed. The diameters of the silver and copper nanoparticles were controlled by changing the voltage conditions. The fabricated silver and copper nano-inks were printed on a flexible polyimide (PI) substrate and sintered at room temperature via a flash light process, using a xenon lamp and varying the light energy. The microstructures of the sintered silver and copper films were observed using a scanning electron microscope (SEM) and a transmission electron microscope (TEM). To investigate the crystal phases of the flash-light-sintered silver and copper films, x-ray diffraction (XRD) was performed. The absorption wavelengths of the silver and copper nano-inks were measured using ultraviolet-visible spectroscopy (UV-vis). Furthermore, the resistivity of the sintered silver and copper films was measured using the four-point probe method and an alpha step. As a result, the fabricated Cu/Ag film shows a high electrical conductivity (4.06 μΩcm), which is comparable to the resistivity of bulk copper (1.68 μΩcm). In addition, the fabricated Cu/Ag nanoparticle film shows superior oxidation stability compared to the Cu nanoparticle film.

  20. Evolution and nucleosynthesis of extremely metal-poor and metal-free low- and intermediate-mass stars II. s-process nucleosynthesis during the core He flash

    CERN Document Server

    Campbell, Simon W; Karakas, Amanda I

    2010-01-01

    Models of primordial and hyper-metal-poor stars with masses similar to the Sun experience an ingestion of protons into the hot core during the core helium flash phase at the end of their red giant branch evolution. This produces a concurrent secondary flash powered by hydrogen burning that gives rise to further nucleosynthesis in the core. We perform post-process nucleosynthesis calculations on a one-dimensional stellar evolution calculation of a star of 1 solar mass and metallicity [Fe/H] = -6.5 that suffers a proton ingestion episode. Our network includes 320 nuclear species and 2,366 reactions and treats mixing and burning simultaneously. The mixing and burning of protons into the hot convective core leads to the production of 13C, which then burns via the 13C(alpha,n)16O reaction releasing a large number of free neutrons. During the first two years of neutron production the neutron poison 14N abundance is low, allowing the prodigious production of heavy elements such as strontium, barium, and lead via slo...

  1. Design of a low-power flash analog-to-digital converter chip for temperature sensors in 0.18 µm CMOS process

    Directory of Open Access Journals (Sweden)

    Al Al

    2015-01-01

    Full Text Available Current paper proposes a simple design of a 6-bit flash analog-to-digital converter (ADC by process in 0.18 μm CMOS. ADC is expected to be used within a temperature sensor which provides analog data output having a range of 360 mV to 560 mV. The complete system consisting of three main blocks, which are the threshold inverter quantization (TIQ-comparator, the encoder and the parallel input serial output (PISO register. The TIQ-comparator functions as quantization of the analog data to the thermometer code. The encoder converts this thermometer code to 6-bit binary code and the PISO register transforms the parallel data into a data series. The design aims to get a flash ADC on low power dissipation, small size and compatible with the temperature sensors. The method is proposed to set each of the transistor channel length to find out the threshold voltage difference of the inverter on the TIQ comparator. A portion design encoder and PISO registers circuit selected a simple circuit with the best performance from previous studies and adjusted to this system. The design has an input range of 285 to 600 mV and 6-bit resolution output. The chip area of the designed ADC is 844.48 x 764.77 µm2 and the power dissipation is 0.162 µW with 1.6 V supply voltage.

  2. Reduction Kinetics of Magnetite Concentrate Particles with Hydrogen at 1150-1600 °C Relevant to a Novel Flash Ironmaking Process

    Science.gov (United States)

    Elzohiery, Mohamed; Mohassab, Yousef; Abdelghany, Amr; Zhang, Shengqin; Chen, Feng; Sohn, Hong Yong

    A novel ironmaking process is under development at the University of Utah aimed at producing iron directly from iron oxide concentrate in a flash reactor. This process will reduce hazardous emissions and save energy. The kinetics of magnetite reduction with hydrogen was previously investigated in our laboratory in the temperature range 1150 to 1400 °C at large temperature increments ( 100 °C increments). Due to the significant melting that occurs above 1350 °C, the reduction kinetics was measured and analyzed in two distinct temperature ranges of 1150 to 1350 °C and 1350 to 1600 °C ( 50 °C increments). Experiments were performed using magnetite concentrate particles of different sizes under various hydrogen partial pressures and residence times. Reduction degrees of more than 90 % were achieved in a few seconds at temperatures as low as 1250 °G Different rate expressions were needed to obtain reliable agreement with experimental data.

  3. Efficient Removal of Arsenic and Antimony During Blast Furnace Smelting of Lead-Containing Materials

    Science.gov (United States)

    Dosmukhamedov, Nurlan; Kaplan, Valery

    2016-10-01

    The efficient removal of impurities, As and Sb, from recycled lead-containing materials is a key issue in the selection of the appropriate smelting technology for projects involving metal reuse. Volatilization of impurities such as As and Sb should occur as early as possible in the process, and preferably within the smelting furnace, so that they do not contaminate the industrial environment nor interfere with the operation of downstream equipment. Using of copper-zinc concentrates in the blast furnace process for recycling lead-containing materials achieves: (1) high copper extraction to matte; (2) high lead extraction to lead bullion; and (3) high zinc extraction to slag, while at the same time producing a more efficient volatilization of As and Sb. Based on both laboratory and industrial data and thermodynamic considerations, the advantages of this blast furnace process for the treatment of recycled lead-containing materials are discussed.

  4. Efficient Removal of Arsenic and Antimony During Blast Furnace Smelting of Lead-Containing Materials

    Science.gov (United States)

    Dosmukhamedov, Nurlan; Kaplan, Valery

    2017-02-01

    The efficient removal of impurities, As and Sb, from recycled lead-containing materials is a key issue in the selection of the appropriate smelting technology for projects involving metal reuse. Volatilization of impurities such as As and Sb should occur as early as possible in the process, and preferably within the smelting furnace, so that they do not contaminate the industrial environment nor interfere with the operation of downstream equipment. Using of copper-zinc concentrates in the blast furnace process for recycling lead-containing materials achieves: (1) high copper extraction to matte; (2) high lead extraction to lead bullion; and (3) high zinc extraction to slag, while at the same time producing a more efficient volatilization of As and Sb. Based on both laboratory and industrial data and thermodynamic considerations, the advantages of this blast furnace process for the treatment of recycled lead-containing materials are discussed.

  5. Urban RoGeR: Merging process-based high-resolution flash flood model for urban areas with long-term water balance predictions

    Science.gov (United States)

    Weiler, M.

    2016-12-01

    Heavy rain induced flash floods are still a serious hazard and generate high damages in urban areas. In particular in the spatially complex urban areas, the temporal and spatial pattern of runoff generation processes at a wide spatial range during extreme rainfall events need to be predicted including the specific effects of green infrastructure and urban forests. In addition, the initial conditions (soil moisture pattern, water storage of green infrastructure) and the effect of lateral redistribution of water (run-on effects and re-infiltration) have to be included in order realistically predict flash flood generation. We further developed the distributed, process-based model RoGeR (Runoff Generation Research) to include the relevant features and processes in urban areas in order to test the effects of different settings, initial conditions and the lateral redistribution of water on the predicted flood response. The uncalibrated model RoGeR runs at a spatial resolution of 1*1m² (LiDAR, degree of sealing, landuse), soil properties and geology (1:50.000). In addition, different green infrastructures are included into the model as well as the effect of trees on interception and transpiration. A hydraulic model was included into RoGeR to predict surface runoff, water redistribution, and re-infiltration. During rainfall events, RoGeR predicts at 5 min temporal resolution, but the model also simulates evapotranspiration and groundwater recharge during rain-free periods at a longer time step. The model framework was applied to several case studies in Germany where intense rainfall events produced flash floods causing high damage in urban areas and to a long-term research catchment in an urban setting (Vauban, Freiburg), where a variety of green infrastructures dominates the hydrology. Urban-RoGeR allowed us to study the effects of different green infrastructures on reducing the flood peak, but also its effect on the water balance (evapotranspiration and groundwater

  6. Optical Flashes Preceding GRBs

    CERN Document Server

    Paczynski, B

    2001-01-01

    Only one optical flash associated with a gamma-ray burst has been detected so far by ROTSE. There are also upper limits obtained by several groups for several bursts. Recent model calculations indicate a possibility that optical flash may precede the GRB. Such flashes are undetectable in the currently popular observing mode, with optical instruments responding to GRB triggers. There is a need to develop all sky optical monitoring system capable of recognizing flashes in real time, and more powerful instruments that could respond robotically to optical triggers and carry out follow up observations.

  7. Pro Android Flash

    CERN Document Server

    Chin, Stephen; Campesato, Oswald

    2011-01-01

    Did you know you can take your Flash skills beyond the browser, allowing you to make apps for Android, iOS and the BlackBerry Tablet OS? Build dynamic apps today starting with the easy-to-use Android smartphones and tablets. Then, take your app to other platforms without writing native code. Pro Android Flash is the definitive guide to building Flash and other rich Internet applications (RIAs) on the Android platform. It covers the most popular RIA frameworks for Android developers - Flash and Flex - and shows how to build rich, immersive user experiences on both Android smartphones and tablet

  8. Statistical Evolution of the Lightning Flash

    Science.gov (United States)

    Zoghzoghy, F. G.; Cohen, M.; Said, R.; Inan, U. S.

    2012-12-01

    Natural lightning is one of the most fascinating and powerful electrical processes on Earth. To date, the physics behind this natural phenomenon are not fully understood, due primarily to the difficulty of obtaining measurements inside thunderstorms and to the wide range of timescales involved (from nanoseconds to seconds). Our aim is to use accurate lightning geo-location data from the National Lightning Detection Network (NLDN) to study statistical patterns in lightning, taking advantage of the fact that millions of lightning flashes occur around the globe every day. We present two sets of results, one involving the patterns of flashes in a storm, and a second involving the patterns of strokes in a flash. These patterns can provide a surrogate measure of the timescales and the spatial extents of the underlying physical processes. First, we study the timescales of charge buildup inside thunderstorms. We find that, following a lightning flash, the probability of another neighboring flash decreases and takes tens of seconds to recover. We find that this suppression effect is a function of flash type, stroke peak current, cloud-to-ground (CG) stroke multiplicity, and other lightning and geographical parameters. We find that the probabilities of subsequent flashes are more suppressed following oceanic lightning, or following flashes with higher peak currents and/or higher multiplicities (for CG flashes). Second, we use NLDN data to study the evolution of the strokes within a CG flash. A CG flash typically includes multiple return strokes, which can occur in the same channel or in multiple channels within a few kilometers. We cluster NLDN stroke data into flashes and produce the probability density function of subsequent strokes as a function of distance and time-delays relative to the previous stroke. Using this technique, we investigate processes which occur during the CG lightning flash with nanosecond to millisecond timescales. For instance, our results suggest

  9. The flash-lag effect and the flash-drag effect in the same display.

    Science.gov (United States)

    Murai, Yuki; Murakami, Ikuya

    2016-09-01

    Visual motion distorts the perceived position of a stimulus. In the flash-drag effect (FDE), the perceived position of a flash appears to be shifted in the direction of nearby motion. In the flash-lag effect (FLE), a flash adjacent to a moving stimulus appears to lag behind. The FLE has been explained by several models, including the differential latency hypothesis, that a moving stimulus has a shorter processing latency than a flash does. The FDE even occurs when the flash is presented earlier than the moving stimulus, and it has been discussed whether this temporal property can be explained by the differential latency model. In the present study, we simultaneously quantified the FDE and FLE using the random jump technique (Murakami, 2001b) and compared their temporal properties. While the positional offset between a randomly jumping stimulus and a flashed stimulus determined the FLE, a drifting grating appeared next to the flash at various stimulus-onset asynchronies to induce the FDE. The grating presented up to 200 ms after the flash onset induced the FDE, whose temporal tuning was explained by a simple convolution model incorporating stochastic fluctuations of differential latency estimated from the FLE data and a transient-sustained temporal profile of motion signals. Thus, a common temporal mechanism to compute the stimulus position in reference to surrounding stimuli governs both the FDE and the FLE.

  10. 高铜铅精矿富氧底吹工业实践%Industrial Practice of Rich Oxygen Bottom Blowing Process of Smelting High Copper Content of Lead Concentrate

    Institute of Scientific and Technical Information of China (English)

    陈学兴; 欧阳坤

    2014-01-01

    A lead factory had smelted a batch of high copper content of lead concentrate , through two months of industrial practice , high copper content of lead concentrate had certain influence to the produc-tion of bottom blowing furnace and fuming furnace . The industrial test results showed that copper can be enriched in the crude lead and matte , the copper content of crude lead can reach more than 10 percent , the copper content of matte can reach more than 40 percent , the copper content of slag can be controlled under 0 .65 percent , and the recovery rate of copper can reach more than 90 percent .%某铅厂处理了一批高铜铅精矿,通过2个月的工业生产,入炉原料含铜高对底吹炉、烟化炉生产有一定影响,整个工业试验结果表明,铜可以在粗铅及锍中富集,粗铅含铜可达10%以上,锍含铜可达40%以上,弃渣含铜可控制在0.65%以下,铜的回收率可达90%。

  11. Step & flash imprint lithography

    Directory of Open Access Journals (Sweden)

    Douglas J. Resnick

    2005-02-01

    Full Text Available The escalating cost of next generation lithography (NGL is driven in part by the need for complex sources and optics. The cost for a single NGL tool could soon exceed $50 million, a prohibitive amount for many companies. As a result, several research groups are looking at alternative, low-cost methods for printing sub-100 nm features. Many of these methods are limited in their ability to do precise overlay. In 1999, Willson and Sreenivasan developed step and flash imprint lithography (S-FIL™. The use of a quartz template opens up the potential for optical alignment of the wafer and template. This paper reviews several key aspects of the S-FIL process, including template, tool, ultraviolet (UV-curable monomer, and pattern transfer. Two applications are also presented: contact holes and surface acoustic wave (SAW filters.

  12. Flash (Ultra-Rapid) Spark-Plasma Sintering of Silicon Carbide

    OpenAIRE

    Eugene A. Olevsky; Stephen M. Rolfing; Maximenko, Andrey L.

    2016-01-01

    A new ultra-rapid process of flash spark plasma sintering is developed. The idea of flash spark plasma sintering (or flash hot pressing - FHP) stems from the conducted theoretical analysis of the role of thermal runaway phenomena for material processing by flash sintering. The major purpose of the present study is to theoretically analyze the thermal runaway nature of flash sintering and to experimentally address the challenge of uncontrollable thermal conditions by the stabilization of the f...

  13. Contribution to the study and design of advanced controllers : application to smelting furnaces

    OpenAIRE

    Ojeda Sarmiento, Juan Manuel

    2013-01-01

    In this doctoral thesis, contributions to the study and design of advanced controllers and their application to metallurgical smelting furnaces are discussed. For this purpose, this kind of plants has been described in detail. The case of study is an Isasmelt plant in south Peru, which yearly processes 1.200.000 tons of copper concentrate. The current control system is implemented on a distributed control system. The main structure includes a cascade strategy to regulate the molten bath tempe...

  14. Production of Welding Fluxes Using Waste Slag Formed in Silicomanganese Smelting

    Science.gov (United States)

    Kozyrev, N. A.; Kryukov, R. E.; Kozyreva, O. E.; Lipatova, U. I.; Filonov, A. V.

    2016-04-01

    The possibility in principle of using slag, which is formed in the silicon-manganese smelting process, in producing welding fluxes is shown. The composition of and technology used for a new fused flux has been designed. A comparative evaluation of the new flux and the widely used AN-348 type flux was done. It has been proved that the new flux has high strength properties.

  15. Municipal Waste Disposal by High Temperature Smelting Technique

    Institute of Scientific and Technical Information of China (English)

    SHEN Zong-bin; ZHANG Chun-xia; ZHANG You-ping; LIU Kun

    2004-01-01

    Municipal waste disposal system by high temperature smelting has the following characteristics: ① The smelting temperature is as high as 1 700-1 800 ℃; ② The dioxin is hardly produced; ③ The secondary pollution can be avoided because of the absence of heavy metals in the flux; ④ The metals and flux after disposal can be reused for construction materials. If outdated, the idle or discarded medium and small blast furnaces can be reconstructed into a waste resource system with high temperature smelting technique, and it is possible to make full use of their existing functions to reduce the investment and exploit their social function of environmental protection. In addition, a new waste disposal system with high temperature smelting was designed based on the recycling municipal waste technology abroad.

  16. Flash-Type Discrimination

    Science.gov (United States)

    Koshak, William J.

    2010-01-01

    This viewgraph presentation describes the significant progress made in the flash-type discrimination algorithm development. The contents include: 1) Highlights of Progress for GLM-R3 Flash-Type discrimination Algorithm Development; 2) Maximum Group Area (MGA) Data; 3) Retrieval Errors from Simulations; and 4) Preliminary Global-scale Retrieval.

  17. Spurious dispersion effects at FLASH

    Energy Technology Data Exchange (ETDEWEB)

    Prat, Eduard

    2009-07-15

    The performance of the Free-Electron Laser (FEL) process imposes stringent demands on the transverse trajectory and size of the electron beam. Since transverse dispersion changes off-energy particle trajectories and increases the effective beam size, dispersion must be controlled. This thesis treats the concept of dispersion in linacs, and analyses the impact of dispersion on the electron beam and on the FEL process. It presents generation mechanisms for spurious dispersion, quantifying its importance for FLASH (Free-electron Laser in Hamburg) and the XFEL (European X-ray Free-Electron Laser). A method for measuring and correcting dispersion and its implementation in FLASH is described. Experiments of dispersion e ects on the transverse beam quality and on the FEL performance are presented. (orig.)

  18. An evaluation of chemical, physical and biological qualities of the inlet and outlet water of desalination plants by reverse osmosis and multistage flash processes in Qeshm Island during

    Directory of Open Access Journals (Sweden)

    Doleh Mohammad

    2016-01-01

    Full Text Available Background and aim: One of the most important components of community’s health is providing clean drinking water. The aim of this study is the quality evaluation of inlet and outlet water of desalination plants in Qeshm by reverse osmosis (RO and Multistage flash (MSF processes and also to compare water quality of outlet from both of process with National and International standards of drinking water. Methods: The cross-sectional descriptive study was carried out during 7 months from November 2011 to May 2012. Sampling was carried out once every two months from inlet and outlet water of desalination plants in Qeshm by RO and MSF processes. Parameters were studied included total hardness, electrical conductivity (EC, total dissolved solid (TDS, turbidity, temperature, pH, fluoride, nitrate, nitrite, chloride, sulfate and biological parameter (total coliform, fecal coliform. Finally, analytical analysis was performed by SPSS (version 16 using paired T- test. Result: Although theresults of this study showed that total hardness and fluoride concentration in the effluent of the both of the processes (RO and MSF were lower than desirable concentration and chloride concentration in RO process was higher than allowable concentration limit, the rest of parameters (chemical and physical in both of processes were in the acceptable range. There was not observed any coliform contamination in the effluent from the both processes (RO and MSF. Conclusion: Due to low fluoride and hardness concentration in the effluent of the both processes (RO and MSF, it should be compensated by adding fluoride and calcium or magnesium compounds. More importantly, the both processes have high capability in providing safe drinking water quality according to water quality standards.

  19. Machine Learning Predictions of Flash Floods

    Science.gov (United States)

    Clark, R. A., III; Flamig, Z.; Gourley, J. J.; Hong, Y.

    2016-12-01

    This study concerns the development, assessment, and use of machine learning (ML) algorithms to automatically generate predictions of flash floods around the world from numerical weather prediction (NWP) output. Using an archive of NWP outputs from the Global Forecast System (GFS) model and a historical archive of reports of flash floods across the U.S. and Europe, we developed a set of ML models that output forecasts of the probability of a flash flood given a certain set of atmospheric conditions. Using these ML models, real-time global flash flood predictions from NWP data have been generated in research mode since February 2016. These ML models provide information about which atmospheric variables are most important in the flash flood prediction process. The raw ML predictions can be calibrated against historical events to generate reliable flash flood probabilities. The automatic system was tested in a research-to-operations testbed enviroment with National Weather Service forecasters. The ML models are quite successful at incorporating large amounts of information in a computationally-efficient manner and and result in reasonably skillful predictions. The system is largely successful at identifying flash floods resulting from synoptically-forced events, but struggles with isolated flash floods that arise as a result of weather systems largely unresolvable by the coarse resolution of a global NWP system. The results from this collection of studies suggest that automatic probabilistic predictions of flash floods are a plausible way forward in operational forecasting, but that future research could focus upon applying these methods to finer-scale NWP guidance, to NWP ensembles, and to forecast lead times beyond 24 hours.

  20. Understanding Green Flashes

    Science.gov (United States)

    Young, Andrew T.

    1998-05-01

    Most astronomers learn about green flashes from either Minnaert's old book (Dover, 1954) or O'Connell's ``The Green Flash....'' Both have defects. Minnaert's account mostly represents what was known in the 1920s; it repeats Mulder's 3-fold classification, which omits Joule's second type of flash --- the one most commonly seen from mountain observatories. O'Connell searched only the astronomical literature, missing Dietze's crucially important paper (Z.f.Met. 9, 169 (1955)) showing that the ``textbook'' mechanism cannot produce flashes visible to the naked eye. He also erred in thinking that distortions of the setting Sun arise in the upper atmosphere (they are due to the marine boundary layer), and copied an error from Feenstra Kuiper's thesis that misidentified a common mirage-like phenomenon as Wegener's ``blank strip'' (Young et al., Appl. Opt. 36, 2689 (1997).) Most phenomena shown in O'Connell's book are caused by inversion layers below eye level, not above as in Wegener's phenomenon. The two commonest forms of green flash are associated with the inferior mirage and the mock mirage, corresponding to Fisher's Type A and Type B sunsets, respectively. Superrefraction, advocated by Wood and by Rayleigh as the cause of large flashes, actually suppress them: the airmass is proportional to the refraction (by Laplace's extinction theorem), so no green is transmitted when refraction is much larger than average. Although there is a physical green flash that can be photographed, the colors seen at sunset are strongly modified by bleaching of the L cones. Most ``green'' sunset flashes are actually yellow. Writers should stop representing Jules Verne's ``ancient legend'' as fact, as it was invented by Verne as a plot device for his novel ``Le Rayon Vert.'' Green-flash photos and simulations will be shown. This material is based upon work supported by the NSF under Award No. ATM-9714357.

  1. Pre-colombian mercury pollution associated with the smelting of argentiferous ores in the Bolivian Andes.

    Science.gov (United States)

    Cooke, Colin A; Balcom, Prentiss H; Kerfoot, Charles; Abbott, Mark B; Wolfe, Alexander P

    2011-02-01

    The development of the mercury (Hg) amalgamation process in the mid-sixteenth century triggered the onset of large-scale Hg mining in both the Old and New Worlds. However, ancient Hg emissions associated with amalgamation and earlier mining efforts remain poorly constrained. Using a geochemical time-series generated from lake sediments near Cerro Rico de Potosí, once the world's largest silver deposit, we demonstrate that pre-Colonial smelting of Andean silver ores generated substantial Hg emissions as early as the twelfth century. Peak sediment Hg concentrations and fluxes are associated with smelting and exceed background values by approximately 20-fold and 22-fold, respectively. The sediment inventory of this early Hg pollution more than doubles that associated with extensive amalgamation following Spanish control of the mine (1574-1900 AD). Global measurements of [Hg] from economic ores sampled world-wide indicate that the phenomenon of Hg enrichment in non-ferrous ores is widespread. The results presented here imply that indigenous smelting constitutes a previously unrecognized source of early Hg pollution, given naturally elevated [Hg] in economic silver deposits.

  2. Intelligent decision support system of operation-optimization in copper smelting converter

    Institute of Scientific and Technical Information of China (English)

    姚俊峰; 梅炽; 彭小奇; 周安梁; 吴冬华

    2002-01-01

    An artificial intelligence technique was applied to the optimization of flux-adding systems and air-blasting systems, the display of on-line parameters, forecasting of mass and compositions of slag in the slagging period, optimization of cold material-adding systems and air-blasting systems, the display of on-line parameters, and the forecasting of copper mass in the copper blow period in copper smelting converters. They were integrated to build the Intelligent Decision Support System of the Operation-Optimization of Copper Smelting Converter(IDSSOOCSC), which is self-learning and self-adaptating. Development steps, monoblock structure and basic functions of the IDSSOOCSC were introduced. After it was applied in a copper smelting converter, every production quota was clearly improved after IDSSOOCSC had been run for 4 months. Blister copper productivity is increased by 6%, processing load of cold input is increased by 8% and average converter life-span is improved from 213 to 235 furnace times.

  3. Self-assembling process of flash nanoprecipitation in a multi-inlet vortex mixer to produce drug-loaded polymeric nanoparticles

    Energy Technology Data Exchange (ETDEWEB)

    Shen Hao [University of Illinois at Chicago, Department of Chemical Engineering (United States); Hong, Seungpyo [University of Illinois at Chicago, Department of Biopharmaceutical Sciences (United States); Prud' homme, Robert K. [Princeton University, Department of Chemical Engineering (United States); Liu Ying, E-mail: liuying@uic.edu [University of Illinois at Chicago, Department of Chemical Engineering (United States)

    2011-09-15

    We present an experimental study of self-assembled polymeric nanoparticles in the process of flash nanoprecipitation using a multi-inlet vortex mixer (MIVM). {beta}-Carotene and polyethyleneimine (PEI) are used as a model drug and a macromolecule, respectively, and encapsulated in diblock copolymers. Flow patterns in the MIVM are microscopically visualized by mixing iron nitrate (Fe(NO{sub 3}){sub 3}) and potassium thiocyanate (KSCN) to precipitate Fe(SCN){sub x}{sup (3-x)+}. Effects of physical parameters, including Reynolds number, supersaturation rate, interaction force, and drug-loading rate, on size distribution of the nanoparticle suspensions are investigated. It is critical for the nanoprecipitation process to have a short mixing time, so that the solvent replacement starts homogeneously in the reactor. The properties of the nanoparticles depend on the competitive kinetics of polymer aggregation and organic solute nucleation and growth. We report the existence of a threshold Reynolds number over which nanoparticle sizes become independent of mixing. A similar value of the threshold Reynolds number is confirmed by independent measurements of particle size, flow-pattern visualization, and our previous numerical simulation along with experimental study of competitive reactions in the MIVM.

  4. Altered cross-modal processing in the primary auditory cortex of congenitally deaf adults: a visual-somatosensory fMRI study with a double-flash illusion.

    Science.gov (United States)

    Karns, Christina M; Dow, Mark W; Neville, Helen J

    2012-07-11

    The developing brain responds to the environment by using statistical correlations in input to guide functional and structural changes-that is, the brain displays neuroplasticity. Experience shapes brain development throughout life, but neuroplasticity is variable from one brain system to another. How does the early loss of a sensory modality affect this complex process? We examined cross-modal neuroplasticity in anatomically defined subregions of Heschl's gyrus, the site of human primary auditory cortex, in congenitally deaf humans by measuring the fMRI signal change in response to spatially coregistered visual, somatosensory, and bimodal stimuli. In the deaf Heschl's gyrus, signal change was greater for somatosensory and bimodal stimuli than that of hearing participants. Visual responses in Heschl's gyrus, larger in deaf than hearing, were smaller than those elicited by somatosensory stimulation. In contrast to Heschl's gyrus, in the superior-temporal cortex visual signal was comparable to somatosensory signal. In addition, deaf adults perceived bimodal stimuli differently; in contrast to hearing adults, they were susceptible to a double-flash visual illusion induced by two touches to the face. Somatosensory and bimodal signal change in rostrolateral Heschl's gyrus predicted the strength of the visual illusion in the deaf adults in line with the interpretation that the illusion is a functional consequence of the altered cross-modal organization observed in deaf auditory cortex. Our results demonstrate that congenital and profound deafness alters how vision and somatosensation are processed in primary auditory cortex.

  5. Self-assembling process of flash nanoprecipitation in a multi-inlet vortex mixer to produce drug-loaded polymeric nanoparticles

    Science.gov (United States)

    Shen, Hao; Hong, Seungpyo; Prud'homme, Robert K.; Liu, Ying

    2011-09-01

    We present an experimental study of self-assembled polymeric nanoparticles in the process of flash nanoprecipitation using a multi-inlet vortex mixer (MIVM). β-Carotene and polyethyleneimine (PEI) are used as a model drug and a macromolecule, respectively, and encapsulated in diblock copolymers. Flow patterns in the MIVM are microscopically visualized by mixing iron nitrate (Fe(NO3)3) and potassium thiocyanate (KSCN) to precipitate Fe(SCN) x (3- x)+ . Effects of physical parameters, including Reynolds number, supersaturation rate, interaction force, and drug-loading rate, on size distribution of the nanoparticle suspensions are investigated. It is critical for the nanoprecipitation process to have a short mixing time, so that the solvent replacement starts homogeneously in the reactor. The properties of the nanoparticles depend on the competitive kinetics of polymer aggregation and organic solute nucleation and growth. We report the existence of a threshold Reynolds number over which nanoparticle sizes become independent of mixing. A similar value of the threshold Reynolds number is confirmed by independent measurements of particle size, flow-pattern visualization, and our previous numerical simulation along with experimental study of competitive reactions in the MIVM.

  6. Floods and Flash Flooding

    Science.gov (United States)

    Floods and flash flooding Now is the time to determine your area’s flood risk. If you are not sure whether you ... If you are in a floodplain, consider buying flood insurance. Do not drive around barricades. If your ...

  7. Fate of recovery boiler smelt nitrogen in the recovery cycle; Soodakattilan sulan typpiyhdisteitten kaeyttaeytyminen talteenottoprosessissa

    Energy Technology Data Exchange (ETDEWEB)

    Hupa, M.; Forssen, M.; Backman, R.; Ek, P.; Hulden, S.G.; Kilpinen, P.; Kymaelaeinen, M.; Malm, H. [Aabo Akademi, Turku (Finland). Combustion Chemistry Research Group

    1997-10-01

    The purpose of this project is to study the fate of the nitrogen bound in the inorganic smelt after it enters the dissolving tank. Of special interest is to find in what form this nitrogen can be found further down in the recovery process and especially in what form it can be removed from the process. The aim is to clarify if the nitrogen can be a potential problem in the process or if it can become a potential emission. The work is divided into choosing methods for the analysis of different nitrogen species, collection and analysis of mill samples, laboratory studies and theoretical studies on nitrogen chemistry in alkaline solutions and reporting

  8. Mercury distribution characteristics in primary manganese smelting plants.

    Science.gov (United States)

    Back, Seung-Ki; Sung, Jin-Ho; Moon, Young-Hoon; Kim, Young-Hee; Seok, Kwang-Seol; Song, Geum-Ju; Seo, Yong-Chil

    2017-08-01

    The mercury (Hg) distribution characteristics were investigated in three primary manganese smelting plants in Korea for the assessment of anthropogenic Hg released. Input and output materials were sampled from each process, and Hg concentrations in the samples were analyzed. Among the input materials, the most mercury was found in the manganese ore (83.1-99.7%) and mercury was mainly released through fly ash or off gas, depending on the condition of off gas cleaning system. As off gas temperature decreases, proportion and concentration of emitted gaseous elemental mercury (Hg(0)) in off gas decreases. Based on mass balance study from these three plants and national manganese production data, the total amount of mercury released from those Korean plants was estimated to 644 kg/yr. About half of it was emitted into the air while the rest was released to waste as fly ash. With the results of this investigation, national inventory for Hg emission and release could be updated for the response to Minamata Convention on Mercury. Copyright © 2017. Published by Elsevier Ltd.

  9. Rapid flash annealing of thermally reactive copolymers in a roll-to-roll process for polymer solar cells

    DEFF Research Database (Denmark)

    Helgesen, Martin; Carlé, Jon Eggert; Andreasen, Birgitta

    2012-01-01

    intensity pulsed light, delivered by a commercial photonic sintering system. Thermally labile ester groups are positioned on the DTZ unit of the copolymer that can be eliminated thermally for enhanced photochemical stability and advantages in terms of processing (solubility/insolubility switching......). The photonic sintering system was successfully implemented in a full roll-to-roll process on flexible PET substrates and large-area polymer solar cell modules were prepared by solution processing of five layers under ambient conditions using the photonic sintering system for thermocleaving of the active layer...

  10. Modeling on Flash Flood Disaster Induced by Bed Load

    Institute of Scientific and Technical Information of China (English)

    CAO Shuyou; LIU Xingnian; HUANG Er; YANG Keiun

    2008-01-01

    Flash floods result from a complex interaction among hydro-meteorological, hydrologi-cal, and hydraulic processes across various spatial and temporal scales. Sichuan Province suffers flash floods frequently owing to mountain weather and topography. A flash flood and gravel bed load transport are two key relative problems in mountain river engineering. Bed materials are often encountered in alternate scouring and deposition in mountain fluvial processes during a flash flood.In this circumstance, CRS-1 bed load numerical model jointly with scale physical model is em-ployed to predict water level and gravel bed scour and deposition for design of flood control dykes and flash flood disaster mitigation. A case study on the mechanism of a flash flood disaster in-duced by bed load transport for a hydropower station in Sichuan Province is conducted. Finally,suggestions to protect the hydropower station are proposed.

  11. West Mining Expanding Into Lead Zinc Smelting Industry

    Institute of Scientific and Technical Information of China (English)

    2008-01-01

    <正>West Mining,China’s 2nd largest lead zinc miner(only next to Yunnan Jinding Zinc with an annual lead and zinc output of approx. 180,000 tons in metal content),has been put- ting efforts on the control of resources for years.Additionally,it has recently increased its investment on smelting business by holding shares of Bayanzhuoer Zijin for more zinc smelting asset.West Mining has just com- pleted the construction of its 60,000-ton zinc

  12. Professional Flash Lite Mobile Development

    CERN Document Server

    Anderson, J G

    2010-01-01

    Discover how to create Flash Lite mobile apps from the ground up. Adobe Flash is an ideal choice for developing rich interactive content for "Flash-enabled" mobile devices; and with this book, you'll learn how to create unique applications with Flash Lite. Through a series of code samples and extensive example applications, you'll explore the core concepts, key features, and best practices of the Flash Lite player. Coverage reveals various ways to develop Flash mobile content, create applications with a cross-platform programming framework based on the Model, View and Controller conc

  13. All-photonic drying and sintering process via flash white light combined with deep-UV and near-infrared irradiation for highly conductive copper nano-ink

    Science.gov (United States)

    Hwang, Hyun-Jun; Oh, Kyung-Hwan; Kim, Hak-Sung

    2016-01-01

    We developed an ultra-high speed photonic sintering method involving flash white light (FWL) combined with near infrared (NIR) and deep UV light irradiation to produce highly conductive copper nano-ink film. Flash white light irradiation energy and the power of NIR/deep UV were optimized to obtain high conductivity Cu films. Several microscopic and spectroscopic characterization techniques such as scanning electron microscopy (SEM), a x-ray diffraction (XRD), and Fourier-transform infrared (FT-IR) spectroscopy were employed to characterize the Cu nano-films. Optimally sintered Cu nano-ink films produced using a deep UV-assisted flash white light sintering technique had the lowest resistivity (7.62 μΩ·cm), which was only 4.5-fold higher than that of bulk Cu film (1.68 μΩ•cm).

  14. Synthesis of cobalt alloy through smelting method and its characterization as prosthesis bone implant

    Energy Technology Data Exchange (ETDEWEB)

    Aminatun,, E-mail: ami-sofijan@yahoo.co.id; Putri, N.S Efinda, E-mail: ami-sofijan@yahoo.co.id; Indriani, Arista, E-mail: ami-sofijan@yahoo.co.id; Himawati, Umi, E-mail: ami-sofijan@yahoo.co.id; Hikmawati, Dyah, E-mail: ami-sofijan@yahoo.co.id; Suhariningsih, E-mail: ami-sofijan@yahoo.co.id [Department of physics, Faculty of Science and Technology, Airlangga University (Indonesia)

    2014-09-25

    Cobalt-based alloys are widely used as total hip and knee replacements because of their excellent properties, such as corrosion resistance, fatigue strength and biocompatibility. In this work, cobalt alloys with variation of Cr (28.5; 30; 31.5; 33, and 34.5% wt) have been synthesized by smelting method began with the process of compaction, followed by smelting process using Tri Arc Melting Furnace at 200A. Continued by homogenization process at recrystallization temperature (1250° C) for 3 hours to allow the atoms diffuses and transform into γ phase. The next process is rolling process which is accompanied by heating at 1200° C for ± 15 minutes and followed by quenching. This process is repeated until the obtained thickness of ± 1 mm. The evaluated material properties included microstructure, surface morphology, and hardness value. It was shown that microstructure of cobalt alloys with variation of Cr is dominant by γ phase, thus making the entire cobalt alloys have high hardness. It was also shown from the surface morphology of entire cobalt alloys sample indicated the whole process of synthesis that had good solubility were at flat surface area. Hardness value test showed all of cobalt alloys sample had high hardness, just variation of 33% Cr be in the range of ASTMF75, it were 345,24 VHN which is potential to be applied as an implant prosthesis.

  15. 连续电镀锌机组预镀镍设备及工艺特点%Equipment and Process Features of Ni-flash Plating in the Continuous Electro Galvanizing Line

    Institute of Scientific and Technical Information of China (English)

    陈晓晓

    2014-01-01

    介绍了连续电镀锌机组的预镀镍过程,详细说明了镀镍设备的优点和预镀镍的工艺条件。采用性能优良的镀镍槽和不溶阳极时,如何保证镀液的 PH 值在3~4是关键的工艺条件,着重介绍了阴离子交换树脂中和 SO2-4和释放 OH-去维持镀液 PH 值的原理。%Ni-flash plating process of the continuous electro galvanizing line (EGL)is described.This report mainly explains the equipment and process conditions of Ni-flash plating.When the Ni-flash plating cell of excellent performance and insoluble anode are applied,maintain the PH value between 3~4 is the key process condition which can be achieved by using anion-exchange resin to absorb SO2-4 and release OH- .

  16. Experimental Study of the Melting and Reduction Behaviour of Ore Used in the HIsarna Process

    NARCIS (Netherlands)

    Qu, Y.

    2013-01-01

    The HIsarna is a coal-based smelting reduction process for ironmaking to drastically reduce CO2 emission and is one of the most promising alternative ironmaking processes under development in the world. The furnace consists of two inter-connected reactors: i) a smelting cyclone, ii) a smelting

  17. Experimental Study of the Melting and Reduction Behaviour of Ore Used in the HIsarna Process

    NARCIS (Netherlands)

    Qu, Y.

    2013-01-01

    The HIsarna is a coal-based smelting reduction process for ironmaking to drastically reduce CO2 emission and is one of the most promising alternative ironmaking processes under development in the world. The furnace consists of two inter-connected reactors: i) a smelting cyclone, ii) a smelting reduc

  18. Foundation Flash Cartoon Animation

    CERN Document Server

    Jones, Tim; Rosson, Allan S

    2008-01-01

    One of Flash s most common uses is still animation for cartoons, games, advertising etc, and this book takes a fresh look at the topic, breaking it down pre-production, production, and post production, and looking at each section in detail, and covering topics such as storyboarding, character libraries and camera mechanics like no Flash book has before. The book is written by members of the Emmy award winning ANIMAX team, who have created work for clients such as Disney, AOL, Fox, WWE, ESPN, and Sesame workshop. This book is an opportunity for them to share their secrets, and is written to sui

  19. Kunpeng Copper:The largest Copper Smelting Company of Sichuan

    Institute of Scientific and Technical Information of China (English)

    2011-01-01

    <正>On September 9,Liangshan Mining Company’s 100,000 tons/year cathode copper project kicked off.It is another key project of the company following the successful launch of the 100,000 tons/year anode copper project.Based on ISA copper smelting technology of the largest open-cast copper mine in southwest China,

  20. General review of flashing jet studies.

    Science.gov (United States)

    Polanco, Geanette; Holdø, Arne Erik; Munday, George

    2010-01-15

    The major concern on the management of superheated liquids, in industrial environments, is the large potential hazards involved in cases of any accidental release. There is a possibility that a violent phase change could take place inside the fluid released generating a flashing jet. This violent phase change might produce catastrophic consequences, such as explosions, fires or toxic exposure, in the installations and in the surroundings. The knowledge and understanding of the mechanisms involved in those releases become an important issue in the prevention of these consequences and the minimization of their impact. This work presents a comprehensive review of information about flashing processes. The review begins with a description of the single phase jet followed by a description of the two-phase flashing jet. The concepts and implications of the thermodynamic and mechanical effects on the behaviour of the jets are considered at the beginning of the review. Following the review is devoted to the classification of the different study approaches used to understand flashing processes in the past, highlighting various critical parameters on the behaviour and the hazard consequences of flashing jets. The review also contains an extensive compilation of experimental, theoretical and numerical data relating to these phenomena, which includes information on the distinct characteristics of the jet, since type of jet, velocity distribution, expansion angle and mass phase change all require individual estimation.

  1. General review of flashing jet studies

    Energy Technology Data Exchange (ETDEWEB)

    Polanco, Geanette, E-mail: gpolanco@usb.ve [Simon Bolivar University, Caracas (Venezuela, Bolivarian Republic of); Holdo, Arne Erik, E-mail: Erik.Holdo@coventry.ac.uk [Narvik University College, Narvik (Norway); Munday, George, E-mail: G.Munday@isaaconsult.co.uk [Coventry University, Coventry (United Kingdom)

    2010-01-15

    The major concern on the management of superheated liquids, in industrial environments, is the large potential hazards involved in cases of any accidental release. There is a possibility that a violent phase change could take place inside the fluid released generating a flashing jet. This violent phase change might produce catastrophic consequences, such as explosions, fires or toxic exposure, in the installations and in the surroundings. The knowledge and understanding of the mechanisms involved in those releases become an important issue in the prevention of these consequences and the minimization of their impact. This work presents a comprehensive review of information about flashing processes. The review begins with a description of the single phase jet followed by a description of the two-phase flashing jet. The concepts and implications of the thermodynamic and mechanical effects on the behaviour of the jets are considered at the beginning of the review. Following the review is devoted to the classification of the different study approaches used to understand flashing processes in the past, highlighting various critical parameters on the behaviour and the hazard consequences of flashing jets. The review also contains an extensive compilation of experimental, theoretical and numerical data relating to these phenomena, which includes information on the distinct characteristics of the jet, since type of jet, velocity distribution, expansion angle and mass phase change all require individual estimation.

  2. Learning Flash CS4 Professional

    CERN Document Server

    Shupe, Rich

    2009-01-01

    Learning Flash CS4 Professional offers beginners and intermediate Flash developers a unique introduction to the latest version of Adobe's powerful multimedia application. This easy-to-read book is loaded with full-color examples and hands-on tasks to help you master Flash CS4's new motion editor, integrated 3D system, and character control using the new inverse kinematics bones animation system. No previous Flash experience is necessary.

  3. Digital Realization of Traditional Animation Process---Taking Flash Paperless Animation System as an Example%传统动画制作工艺的数字化实现--以Flash无纸动画系统为例

    Institute of Scientific and Technical Information of China (English)

    王丛明

    2014-01-01

    本文首先总结了传统动画生产的工艺流程,然后按照流程顺序提出数字化的设想并论述了动画生产工艺流程数字化的优势,接着设计并论述了基于Flash技术进行传统动画生产工艺流程中各环节的实现。通过动画前期、中期、后期技术环节的解析与Flash技术的结合研究,设计了基于Flash动画技术的无纸动画制作系统的解决方案。%This paper first summarizes the process of traditional animation, and then proposes digital con-ceives according to the process and describes its advantage. The paper designs and discusses the realization of each link in the production of traditional animation based on Flash technology. Combining with the analysis on different steps of the animation technology and the Flash technology, we come to the Flash paperless animation system.

  4. Flash Builder and Flash Catalyst The New Workflow

    CERN Document Server

    Peeters, Steven

    2010-01-01

    The Flash Platform is changing. Flash Builder and Flash Catalyst have brought a new separation of design and coding to web development that enables a much more efficient and streamlined workflow. For designers and developers used to the close confines of Flash, this is a hugely liberating but at first alien concept. This book teaches you the new workflow for the Flash platform. It gives an overview of the technologies involved and provides you with real-world project examples and best-practice guidelines to get from design to implementation with the tools at hand. * Includes many examples* Foc

  5. Reactive Flash Simulation of the Continuous Melt Transesterification Process of Polycarbonate%聚碳酸酯连续熔融酯交换过程的反应闪蒸模拟

    Institute of Scientific and Technical Information of China (English)

    秦吉臣; 谢小莉; 曹贤武; 瞿金平

    2007-01-01

    A model of the continuous melt transesterification process of bisphenol-A and diphenyl carbonate in a continuous stirred tank reactor to produce polycarbonate is presented. The model is developed by using the molecular species model of polycarbonate melt polycondensation and the modeling method of reactive flash. Liquid phase is treated as perfect mixed flow and the vapor phase is assumed following the ideal gas law. With this model,the continuous melt transesterification process of bisphenol-A and diphenyl carbonate is examined with respect to different process parameters.

  6. Jaan Toomik Flash Artis

    Index Scriptorium Estoniae

    1999-01-01

    1999. a. mai-juuni 'Flash Artis' on ajakirja Eesti korrespondendi Ando Keskküla artikkel Jaan Toomikust. Jaan Toomik on kutsutud esinema Londoni The Photographers' Gallery grupinäitusele, tema videot 'Father and Son' näidatakse Londonis avataval näitusel 'Near and Elsewhere' 11.-24. juunini

  7. Inessa Josing Flash Artis

    Index Scriptorium Estoniae

    1999-01-01

    'Flash Art'i' 1998. a. nov.-dets. numbris Rosa Martínezi artiklis suvisest Manifesta II näitusest Luxembourg'is on positiivselt mainitud ka Inessa Josingut. Illustratsiooniks toodud seitsmest fotost ühel on I. Josingu aknakujundus 'What Must I Do to be Saved?'

  8. Inessa Josing Flash Artis

    Index Scriptorium Estoniae

    1999-01-01

    'Flash Art'i' 1998. a. nov.-dets. numbris Rosa Martínezi artiklis suvisest Manifesta II näitusest Luxembourg'is on positiivselt mainitud ka Inessa Josingut. Illustratsiooniks toodud seitsmest fotost ühel on I. Josingu aknakujundus 'What Must I Do to be Saved?'

  9. Jaan Toomik Flash Artis

    Index Scriptorium Estoniae

    1999-01-01

    1999. a. mai-juuni 'Flash Artis' on ajakirja Eesti korrespondendi Ando Keskküla artikkel Jaan Toomikust. Jaan Toomik on kutsutud esinema Londoni The Photographers' Gallery grupinäitusele, tema videot 'Father and Son' näidatakse Londonis avataval näitusel 'Near and Elsewhere' 11.-24. juunini

  10. A Coupling Dynamic Model for Dissolution and Reduction of Chromium Ore in a Smelting Reduction Converter%A Coupling Dynamic Model for Dissolution and Reduction of Chromium Ore in a Smelting Reduction Converter

    Institute of Scientific and Technical Information of China (English)

    LIU Yan; JIANG Mao-fa; XU Li-xian; WANG De-yong

    2012-01-01

    For describing and resolving the process of chromium ore smelting reduction in a converter preferably, the coupling dynamic model was established based on the kinetic models of chromium ore dissolution and interfacial re- ducing reaction between the slag and metal. When 150 t stainless steel crude melts with chromium of 12% are produced in a smelting reduction converter with no initial chromium in metal at 1 560℃, the results of the coupling dynamic model show that the mean reduction rate and injection rate of chromium ore are 0. 091% ·min^-1 and 467 kg · min^-1 , respectively. The foundation of the coupling dynamic model provides a reference and basis on the constitution of rational processing route for a practical stainless steelmaking.

  11. Mental models of flash floods and landslides.

    Science.gov (United States)

    Wagner, Klaus

    2007-06-01

    Perceptions of flash floods and landslides were analyzed in four communities of the Bavarian Alps using the mental model approach. Thirty-eight qualitative interviews, two telephone surveys with 600 respondents, and two onsite interviews (74/95 respondents) were conducted. Mental models concerning flash floods are much better developed than those for landslides because the key physical processes for flash floods are easier for the general public to recognize and understand. Mental models are influenced by the local conditions. People who have a better knowledge about the hazards are those who use many different sources to inform themselves, express fear about natural hazards, or have previous experience with hazards. Conclusions for how to improve information for the general public are discussed.

  12. 高硅白云石皮江法炼镁实验%High Silica Dolomite Pidgeon Smelt Magnesium Experiment

    Institute of Scientific and Technical Information of China (English)

    李波; 褚丙武

    2015-01-01

    Magnesium smelting by Pidgeon process requirements SiO2 should be less than 0 .5% in dolomite . Previous studies that SiO2 with MgO style in the high temperature generated 2MgO.SiO2 , It's a kind of low melting point compound . It can make the dolomite sintering . It lets the calcined dolomite could not reach the requirements of smelting magnesium , a certain extent , reduce the yield .This paper studies the reason of low yield in magnesium smelting by Pidgeon process used high silica ( SiO 2 4 .51% ) dolomite . And proposed and verified by the experimental it can achieve high magnesium yield high by Pidgeon process used high silica ( SiO2 4 .51% ) dolomite . It is possible of magnesium smelting by Pidgeon process used high silica dolomite .%皮江法炼镁要求白云石中SiO2应小于0.5%。前人研究认为SiO2在高温时与MgO生成2M gO · SiO2,这是一种低熔点化合物,它会使白云石烧结,使煅烧后的白云石达不到炼镁的要求,在一定程度上降低收得率。本文研究了高硅(SiO2为4.51%)白云石皮江法炼镁镁收率低的原因,提出并通过实验验证了高硅白云石采用皮江法炼镁,也可以达到高的镁收率。使高硅白云石采用皮江法炼镁成为可能。

  13. The Exact Art and Subtle Science of DC Smelting: Practical Perspectives on the Hot Zone

    Science.gov (United States)

    Geldenhuys, Isabel J.

    2017-02-01

    Increasingly, sustainable smelting requires technology that can process metallurgically complex, low-grade, ultra-fine and waste materials. It is likely that more applications for direct current (DC) technology will inevitably follow in the future as DC open-arc furnaces have some wonderful features that facilitate processing of a variety of materials in an open-arc open-bath configuration. A DC open-arc furnace allows for optimization and choice of chemistry to benefit the process, rather than being constrained by the electrical or physical properties of the material. In a DC configuration, the power is typically supplied by an open arc, providing relative independence and thus an extra degree of freedom. However, if the inherent features of the technology are misunderstood, much of the potential may never be realised. It is thus important to take cognisance of the freedom an operator will have as a result of the open arc and ensure that operating strategies are implemented. This extra degree of freedom hands an operator a very flexible tool, namely virtually unlimited power. Successful open-arc smelting is about properly managing the balance between power and feed, and practical perspectives on the importance of power and feed balance are presented to highlight this aspect as the foundation of proper open-arc furnace control.

  14. The lightning flash

    CERN Document Server

    Cooray, Vernon

    2014-01-01

    With contributions from today's leading lightning engineers and researchers, this updated 2nd edition of Vernon Cooray's classic text, The Lightning Flash provides the reader with an essential introduction to lightning and its impact on electrical and electronic equipment. Providing the reader with a thorough background into almost every aspect of lightning and its impact on electrical and electronic equipment, this new edition is updated throughout and features eight new chapters that bring the science up to date.

  15. Physics Flash December 2016

    Energy Technology Data Exchange (ETDEWEB)

    Kippen, Karen Elizabeth [Los Alamos National Lab. (LANL), Los Alamos, NM (United States). ADEPS Communications

    2016-12-01

    This is the December 2016 issue of Physics Flash, the newsletter of the Physics Division of Los Alamos National Laboratory (LANL). In this issue, the following topics are covered: Novel liquid helium technique to aid highly sensitive search for a neutron electrical dipole moment; Silverleaf: Prototype Red Sage experiments performed at Q-site; John L. Kline named 2016 APS Fellow; Physics students in the news; First Entropy Engine quantum random number generator hits the market; and celebrating service.

  16. Physics Flash August 2016

    Energy Technology Data Exchange (ETDEWEB)

    Kippen, Karen Elizabeth [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

    2016-08-25

    Physics Flash is the newsletter for the Physics Division at Los Alamos National Laboratory. This newsletter is for August 2016. The following topics are covered: "Accomplishments in the Trident Laser Facility", "David Meyerhofer elected as chair-elect APS Nominating Committee", "HAWC searches for gamma rays from dark matter", "Proton Radiography Facility commissions electromagnetic magnifier", and "Cosmic ray muon computed tomography of spent nuclear fuel in dry storage casks."

  17. Smelting reduction and kinetics analysis of magnetic iron in copper slag using waste cooking oil.

    Science.gov (United States)

    Li, Bo; Wang, Xubin; Wang, Hua; Wei, Yonggang; Hu, Jianhang

    2017-05-25

    To improve the recovery of copper, the viscosity of copper molten slag is decreased by the reduction of magnetic iron, which, in turn, accelerates the settling and separation of copper droplets from the slag. A new technology is proposed in which waste cooking oil is used as a reductant to reduce magnetic iron in the copper smelting slag and consequently reduce carbon emissions in the copper smelting process. A kinetic model of the reduction of magnetic iron in copper slag by waste cooking oil was built using experimental data, and the accuracy of the model was verified. The results indicated that the magnetic iron content in the copper slag decreased with increasing reduction time and an increase in temperature more efficiently reduced magnetic iron in the copper slag. The magnetic iron in the copper slag gradually transformed to fayalite, and the viscosity of the copper molten slag decreased as the magnetic iron content decreased during the reduction process. The reduction of magnetic iron in the copper molten slag using waste cooking oil was a first-order reaction, and the rate-limiting step was the mass transfer of Fe3O4 through the liquid boundary layer.

  18. Rh-flash acquisition card

    CERN Document Server

    Bourrion, O

    2003-01-01

    The rh-flash card main purpose is to convert and store the image of the analog data present at input into an output buffer, namely in a given timing window besides a stop signal (like a digital oscilloscope). It is conceived in VME format 1U wide with an additional connector. Novelty of this card is its ability to sample at a high frequency, due to flash coders, and this at a high repetition rate. To do that the card allows the storage of the data considered 'useful' and that is done by storing only the data exceeding a certain threshold. This can be useful for instance for viewing peaks in a spectrum, and obtaining their relative location. The goal is to stock and process the data sampled before and after the arrival of a stop signal (what entails a storage depth). A threshold is defined and any peak exceeding its level will really be stored in the output buffer which is readable through the VME bus. The peak values will be stored as well as m preceding and n subsequent values (both programmable). Obviously,...

  19. Extracting phosphoric iron under laboratorial conditions smelting bog iron ores

    Science.gov (United States)

    Török, B.; Thiele, A.

    2013-12-01

    In recent years it has been indicated by archaeometric investigations that phosphoric-iron (P-iron, low carbon steel with 0,5-1,5wt% P), which is an unknown and unused kind of steel in the modern industry, was widely used in different parts of the world in medieval times. In this study we try to explore the role of phosphorus in the arhaeometallurgy of iron and answer some questions regarding the smelting bog iron ores with high P-content. XRF analyses were performed on bog iron ores collected in Somogy county. Smelting experiments were carried out on bog iron ores using a laboratory model built on the basis of previously conducted reconstructed smelting experiments in copies of excavated furnaces. The effect of technological parameters on P-content of the resulted iron bloom was studied. OM and SEM-EDS analyses were carried out on the extracted iron and slag samples. On the basis of the material analyses it can be stated that P-iron is usually extracted but the P-content is highly affected by technological parameters. Typical microstructures of P-iron and of slag could also be identified. It could also be established that arsenic usually solved in high content in iron as well.

  20. Features of positive ground flashes observed in Kathmandu Nepal

    Science.gov (United States)

    Adhikari, Pitri Bhakta; Sharma, Shriram; Baral, Kedarnath

    2016-07-01

    Lightning vertical electric fields pertinent to the subtropical thunderstorms occurring over the rugged terrain have been measured and recorded at a hilly station Kathmandu, Nepal. In the present work, waveforms of the positive ground flashes have been selected from all the records and were analyzed. To the best of our knowledge, this is the first time that fine structure of electric field signature pertinent to the positive return stroke; have been analyzed and presented from Nepal. One hundred and thirty three (133) of the total of four hundred twenty-five (425) flashes were selected from seven thunderstorm days and analyzed. Of the data recorded for seven days, 133 flashes (31.3%) were positive flashes and 276 flashes (64.9%) were cloud flashes. Majority of the positive ground flashes were found to be single stroke ones, whereas, the average number of strokes per flash is found to be 1.1 with a maximum value of 4. Majority of the positive ground flashes were found either lacking the initial breakdown process and the leader stage or these processes could not be detected. The return strokes are found to be succeeded by large in cloud activity in the continuing current portion of the flash. The average zero-crossing time of the positive return strokes was found to be 60.45 μs with a range of 447.81 μs and the average rise time was found to be 9.44 μs with a range of 42.56 μs.

  1. 应用遗传算法求解AOD全铁水冶炼和电炉钢水冶炼不锈钢混合流程的最优调度问题%Applying Genetic Algorithm for Solving the Scheduling Problem of Stainless Steel Smelting Hybrid Process Combined All Hot Metal in AOD With Molten Steel in EAF

    Institute of Scientific and Technical Information of China (English)

    冯凯; 汪红兵; 田乃媛; 贺东风; 徐安军

    2012-01-01

    The optimized scheduling about both all hot metal in AOD and molten steel in EAF stainless steel smel ting process was investigated. The results show that the deficiency of the longer tap to tap time of EAF in the flow with molten steel in EAF can be solved by introducing the flow with all hot metal in AOD. The stainless steel smelting hybrid flow combined all hot metal in AOD with molten steel in EAF was provided. The optimized sched uling aiming at the longest ladle track time between production processes minimizing was proposed. The longest ladle track time between production processes for a minimum of 60 min was calculated by using the genetic algo-rithm and less than the time of the production scheduling as the center of continuous casting. The conventional ladle track time was ensured and regulated with enough time. The Gantt chart of optimized scheduling about the hy- brid flow was proposed. The temperature schedule was given based on the temperature decrease empirical formula.%研究了AOD全铁水冶炼和电炉钢水冶炼两种不锈钢冶炼流程,结果表明,AOD全铁水冶炼不锈钢可以弥补电炉钢水冶炼流程中电炉产能小于连铸产能的缺陷。提出了一种结合AOD全铁水冶炼和电炉钢水冶炼的混合流程。提出了各个工序间钢包最长传搁时间最短为调度目标是更加合理的调度方式,应用遗传算法求解混合流程最长钢包传搁时间最小为60min,小于单纯以连铸机为中心的组织生产调度,既保证了钢包正常的运输,又有足够的时间进行必要的调度和调整。最后,给出混合流程最优调度的甘特图,并基于最优调度并采用统计分析的方法得出:亡序问传搁过程温降的经验公式,由此给出混合流程最优调度的温度制度。

  2. 纳雍钼镍矿的熔池熔炼%Bath Smelting of Nayong Molybdenum Nickel Ore

    Institute of Scientific and Technical Information of China (English)

    周方栋; 伍耀明

    2012-01-01

    In this paper, analysis and concrete terms of the nature and composition of a detailed theoretical of nickel-molybdenum mineral of Nayong, to clarify the various elements in the mineral bath smelting process behavior. Analysis to achieve separation of molybdenum pyrometallurgical nickel smelting favorable conditions and mature furnace. That as long as the measures taken to collecting reliable smelting slag and enhanced leaching method, to obtain a high yield of Mo-Ni, high-quality products and to provide arsenic-free sulfuric acid and sulfur dioxide gas is possible.%文章对纳雍钼镍矿的矿物性质和成分进行了详细的理论分析和具体计算,阐明了矿物中各元素在熔池熔炼过程中的行为。分析了实现火法冶炼分离钼镍的有利条件和成熟的冶炼炉型。指出只要采取可靠的收尘措施和强化浸出熔炼渣的方法,获得钼镍的高收率、高品质的产品以及提供无砷的二氧化硫烟气制硫酸是可能的。

  3. Photosynthetic efficiency of Chlamydomonas reinhardtii in flashing light

    NARCIS (Netherlands)

    Vejrazka, C.; Janssen, M.G.J.; Streefland, M.; Wijffels, R.H.

    2011-01-01

    Efficient light to biomass conversion in photobioreactors is crucial for economically feasible microalgae production processes. It has been suggested that photosynthesis is enhanced in short light path photobioreactors by mixing-induced flashing light regimes. In this study, photosynthetic efficienc

  4. Photosynthetic efficiency of Chlamydomonas reinhardtii in flashing light

    NARCIS (Netherlands)

    Vejrazka, C.; Janssen, M.G.J.; Streefland, M.; Wijffels, R.H.

    2011-01-01

    Efficient light to biomass conversion in photobioreactors is crucial for economically feasible microalgae production processes. It has been suggested that photosynthesis is enhanced in short light path photobioreactors by mixing-induced flashing light regimes. In this study, photosynthetic

  5. Reassessment of the predatory effects of rainbow smelt on ciscoes in Lake Superior

    Science.gov (United States)

    Myers, Jared T.; Jones, Michael L.; Stockwell, Jason D.; Yule, Daniel L.

    2009-01-01

    Evidence from small lakes suggests that predation on larval ciscoes Coregonus artedi by nonnative rainbow smelt Osmerus mordax can lead to cisco suppression or extirpation. However, evidence from larger lakes has led to equivocal conclusions. In this study, we examine the potential predation effects of rainbow smelt in two adjacent but contrasting embayments in Lake Superior (Thunder and Black bays, Ontario). During May 2006, we sampled the ichthyoplankton, pelagic fish communities, and diet composition of rainbow smelt in both bays. Using acoustics and midwater trawling, we estimated rainbow smelt densities to be 476 ± 34/ha (mean ± SE) in Thunder Bay and 3,435 ± 460/ha in Black Bay. We used a bioenergetics model to estimate the proportion of cisco larvae consumed by rainbow smelt. Our results suggest that predation by rainbow smelt accounts for 15–52% and 37–100% of the mortality of larval ciscoes in Thunder and Black bays, respectively, depending on the predator feeding rate and the scale of predator–prey overlap. We also examined the sensitivity of past conclusions (based on 1974 field collections) to assumptions of temporal overlap between rainbow smelt and larval ciscoes and estimates of rainbow smelt abundance derived from bottom trawl samples. After adjusting these parameters to reflect current understanding, we found that the previous predation estimates may have been conservative. We conclude that rainbow smelt may have been a more important contributor to the demise and slow recovery of ciscoes in Lake Superior than previously thought.

  6. Flash Point Performance Evaluation

    Science.gov (United States)

    2014-03-01

    7094 Grabner D3828B Seta Flash CL12-3453 42.5 43.8 43.8 47.7 44.3 47.3 42.0 42.5 43.8 43.8 47.7 45.3 47.2 42.0 CL12-3475 58.5 61.7 58.7 59.7 61.3...division of Petroleum Analyzers Company (PAC) Houston, TX 14. Herzog is division of PAC 15. Stanhope- Seta , London, UK 16. Grabner Instruments is a

  7. Methods of flash sintering

    Energy Technology Data Exchange (ETDEWEB)

    Raj, Rishi; Cologna, Marco; Francis, John S.

    2016-05-10

    This disclosure provides methods of flash sintering and compositions created by these methods. Methods for sintering multilayered bodies are provided in which a sintered body is produced in less than one minute. In one aspect, each layer is of a different composition, and may be constituted wholly from a ceramic or from a combination of ceramic and metallic particles. When the body includes a layer of an anode composition, a layer of an electrolyte composition and a layer of a cathode composition, the sintered body can be used to produce a solid oxide fuel cell.

  8. High-fidelity flash lidar model development

    Science.gov (United States)

    Hines, Glenn D.; Pierrottet, Diego F.; Amzajerdian, Farzin

    2014-06-01

    NASA's Autonomous Landing and Hazard Avoidance Technologies (ALHAT) project is currently developing the critical technologies to safely and precisely navigate and land crew, cargo and robotic spacecraft vehicles on and around planetary bodies. One key element of this project is a high-fidelity Flash Lidar sensor that can generate three-dimensional (3-D) images of the planetary surface. These images are processed with hazard detection and avoidance and hazard relative navigation algorithms, and then are subsequently used by the Guidance, Navigation and Control subsystem to generate an optimal navigation solution. A complex, high-fidelity model of the Flash Lidar was developed in order to evaluate the performance of the sensor and its interaction with the interfacing ALHAT components on vehicles with different configurations and under different flight trajectories. The model contains a parameterized, general approach to Flash Lidar detection and reflects physical attributes such as range and electronic noise sources, and laser pulse temporal and spatial profiles. It also provides the realistic interaction of the laser pulse with terrain features that include varying albedo, boulders, craters slopes and shadows. This paper gives a description of the Flash Lidar model and presents results from the Lidar operating under different scenarios.

  9. Recovery of aluminium from secondary aluminum dross using low-temperature alkaline smelting%二次铝灰低温碱性熔炼研究

    Institute of Scientific and Technical Information of China (English)

    郭学益; 李菲; 田庆华; 计坤

    2012-01-01

    The process of extracting aluminum from secondary aluminum dross vising low-temperature alkaline smelting was studied. The factors, including alkali dross ratio, the addition of different addictive, salt dross ratio, smelting temperature, smelting time, and different mix methods in smelting, were addressed during the transfer of AI into water soluble salt. The results show that the optimum conditions of the process are determined as follows: alkali dross ratio 1.3, salt dross ratio 0.7 (NaNO3) or 0.4 (Na2O2), smelting temperature 500 ℃, smelting time 60 min. Wet mixture of the sample can improve the leaching efficiency of aluminum. 87.52% of Al might be leached in water with dry mixing of the sample, while 92.71% of Al may be leached with wet mixing by using NaNO3 as addictive in smelting process, and 92.76% of Al can be dissolved with Na2O2 as additive.%研究利用低温碱性熔炼法提取二次铝灰中铝的过程.探讨碱灰质量比、盐灰质量比、熔炼温度、熔炼时间、不同添加剂和不同混料方式等因素对铝浸出率的影响.研究结果表明:优化条件为:碱灰质量比1.3、盐灰质量比0.7(NaNO3)或0.4(Na2O2)、熔炼温度500℃、熔炼时间60 min.湿混料可以提高铝浸出率,以NaNO3为添加剂干混料铝浸出率最高可达87.52%,以NaNO3为添加剂湿混料铝浸出率最高可达92.71%,以Na2O2为添加剂湿混料铝浸出率最高可达92.76%.

  10. Ecological factors affecting Rainbow Smelt recruitment in the main basin of Lake Huron, 1976-2010

    Science.gov (United States)

    O'Brien, Timothy P.; Taylor, William W.; Roseman, Edward F.; Madenjian, Charles P.; Riley, Stephen C.

    2014-01-01

    Rainbow Smelt Osmerus mordax are native to northeastern Atlantic and Pacific–Arctic drainages and have been widely introduced throughout North America. In the Great Lakes region, Rainbow Smelt are known predators and competitors of native fish and a primary prey species in pelagic food webs. Despite their widespread distribution, importance as a prey species, and potential to negatively interact with native fish species, there is limited information concerning stock–recruitment relationships for Rainbow Smelt. To better understand recruitment mechanisms, we evaluated potential ecological factors determining recruitment dynamics for Rainbow Smelt in Lake Huron using data from bottom trawl catches. We specifically evaluated influence of stock size, environmental factors (water temperature, lake levels, and precipitation), and salmonine predation on the production of age-0 recruits from 1976 to 2010. Rainbow Smelt recruitment was negatively related to stock size exceeding 10 kg/ha, indicating that compensatory, density-dependent mortality from cannibalism or intraspecific competition was an important factor related to the production of age-0 recruits. Recruitment was positively related to spring precipitation suggesting that the amount of stream-spawning habitat as determined by precipitation was important for the production of strong Rainbow Smelt recruitment. Additionally, density of age-0 Rainbow Smelt was positively related to Lake Trout Salvelinus namaycush abundance. However, spawning stock biomass of Rainbow Smelt, which declined substantially from 1989 to 2010, was negatively associated with Lake Trout catch per effort suggesting predation was an important factor related to the decline of age-2 and older Rainbow Smelt in Lake Huron. As such, we found that recruitment of Rainbow Smelt in Lake Huron was regulated by competition with or cannibalism by older conspecifics, spring precipitation influencing stream spawning habitats, and predation by Lake Trout on

  11. Metamodeling and Optimization of a Blister Copper Two-Stage Production Process

    Science.gov (United States)

    Jarosz, Piotr; Kusiak, Jan; Małecki, Stanisław; Morkisz, Paweł; Oprocha, Piotr; Pietrucha, Wojciech; Sztangret, Łukasz

    2016-06-01

    It is often difficult to estimate parameters for a two-stage production process of blister copper (containing 99.4 wt.% of Cu metal) as well as those for most industrial processes with high accuracy, which leads to problems related to process modeling and control. The first objective of this study was to model flash smelting and converting of Cu matte stages using three different techniques: artificial neural networks, support vector machines, and random forests, which utilized noisy technological data. Subsequently, more advanced models were applied to optimize the entire process (which was the second goal of this research). The obtained optimal solution was a Pareto-optimal one because the process consisted of two stages, making the optimization problem a multi-criteria one. A sequential optimization strategy was employed, which aimed for optimal control parameters consecutively for both stages. The obtained optimal output parameters for the first smelting stage were used as input parameters for the second converting stage. Finally, a search for another optimal set of control parameters for the second stage of a Kennecott-Outokumpu process was performed. The optimization process was modeled using a Monte-Carlo method, and both modeling parameters and computed optimal solutions are discussed.

  12. Flashing LEDs for Microalgal Production.

    Science.gov (United States)

    Schulze, Peter S C; Guerra, Rui; Pereira, Hugo; Schüler, Lisa M; Varela, João C S

    2017-08-30

    Flashing lights are next-generation tools to mitigate light attenuation and increase the photosynthetic efficiency of microalgal cultivation systems illuminated by light-emitting diodes (LEDs). Optimal flashing light conditions depend on the reaction kinetics and properties of the linear electron transfer chain, energy dissipation, and storage mechanisms of a phototroph. In particular, extremely short and intense light flashes potentially mitigate light attenuation in photobioreactors without impairing photosynthesis. Intelligently controlling flashing light units and selecting electronic components can maximize light emission and energy efficiency. We discuss the biological, physical, and technical properties of flashing lights for algal production. We combine recent findings about photosynthetic pathways, self-shading in photobioreactors, and developments in solid-state technology towards the biotechnological application of LEDs to microalgal production. Copyright © 2017 Elsevier Ltd. All rights reserved.

  13. 浅淡盐硝联产无闪发罐专利工艺的应用%Brief Discussion on the Application of Patented Process in the Co-Production of Salt and Sodium Sulfate without Flash Evaporator

    Institute of Scientific and Technical Information of China (English)

    龙国平

    2012-01-01

    According to the process analysis of the imported facility of co-production of salt and sodium sulfate in vacuum salt making and in combination with the process of the co-production of salt and sodium sulfate in Xuzhou Fengcheng Salt and Chemical Co.,Ltd,this paper briefly discusses the patented process of the co-production of salt and sodium sulfate without flash evaporator which is of references for colleagues.%根据国内引进的真空制盐盐硝联产工艺分析,结合徐州丰成盐化工有限公司真空制盐盐硝联产工艺,浅淡取消闪发罐的盐硝联产专利工艺,仅供同行参考。

  14. Intelligent predictive model of ventilating capacity of imperial smelt furnace

    Institute of Scientific and Technical Information of China (English)

    唐朝晖; 胡燕瑜; 桂卫华; 吴敏

    2003-01-01

    In order to know the ventilating capacity of imperial smelt furnace (ISF), and increase the output of plumbum, an intelligent modeling method based on gray theory and artificial neural networks(ANN) is proposed, in which the weight values in the integrated model can be adjusted automatically. An intelligent predictive model of the ventilating capacity of the ISF is established and analyzed by the method. The simulation results and industrial applications demonstrate that the predictive model is close to the real plant, the relative predictive error is 0.72%, which is 50% less than the single model, leading to a notable increase of the output of plumbum.

  15. The Advancement in Intensified Smelting Technology of Baosteel Blast Furnace

    Institute of Scientific and Technical Information of China (English)

    LinChengcheng; ZhangLonglai

    2005-01-01

    Baosteel always aims at becoming one of the most profitable enterprises in the world, enjoying international competence,benchmarking with the world advanced level, pursuing innovation sustainable development. Recent years, Baosteel Iron-making Department has caught the opportunity of increasing steel demand; conquering disadvantages such as changeable up-stream market, fuel and raw material's fight supplies and lower quality, etc. In our department, Major technical problems have been overcome, blast furnace intensified smelting technology improved, the cost of molten iron under control, blast fttmace long-life span control technology made breakthrough, and Baosteel's ironmaking capacity improved further.

  16. The 20 February 2010 Madeira Island flash-floods: VHR satellite imagery processing in support of landslide inventory and sediment budget assessment

    Directory of Open Access Journals (Sweden)

    C. Lira

    2013-03-01

    Full Text Available On 20 February 2010, an extreme rainfall episode occurred on Madeira Island, which caused an exceptionally strong flash flood and several soil slip-debris flows, producing 45 confirmed deaths and 6 persons declared missing, as well as extensive material damages. In order to understand and quantify the importance of landsliding in routing sediment through mountainous drainage, such as Madeira Island's landscape, it was essential to perform extensive landslide analysis. This study describes the methodology used to semi-automatically detect the landslides, produce the landslide inventory maps and estimate the sediment volume produced during this particular event which ranged from 217 000 m3 to 344 000 m3 and 605 000 m3 to 984 000 m3 for the Funchal and Ribeira Brava basins, respectively. These results contributed to the design and implementation of measures to prevent damages caused by landslides in Madeira Island.

  17. Recovery of Ductility in Ultrafine-Grained Low-Carbon Steel Processed Through Equal-Channel Angular Pressing Followed by Cold Rolling and Flash Annealing

    Science.gov (United States)

    Singh, Raj Bahadur; Mukhopadhyay, N. K.; Sastry, G. V. S.; Manna, R.

    2017-01-01

    The low-carbon steel workpieces are deformed by equal-channel angular pressing at 293 K (20 °C) up to an equivalent strain of 12 using route B c, which results in the bulk ultrafine-grained (UFG) structure with high dislocation density and partial dissolution of cementite. The yield strength (YS) is enhanced from 208 (as-received) to 872 MPa and the tensile strength is increased from 362 to 996 MPa, but the material loses total elongation (TE) from 36.2 to 2.9 pct. Cold rolling of equal-channel angular pressed steel produces the refined structure of grain size 0.11 μm. The YS increases further to 924 MPa with a marginal gain in ductility due to the reappearance of the γ fiber component. Flash annealing the samples, which were equal-channel angular pressed followed by cold rolling, at 873 K (600 °C) results in 27 pct of micron-sized (9 µm) ferrite grains in submicron-sized (<1 µm) matrix with a reduced defect density and small amount of precipitation of cementite. TE increases from 2.9 to 23.3 pct. The material retains a YS of 484 MPa and tensile strength of 517 MPa, which are higher than those of the as-received material. The UFG grains are failed by cleavage, but the micron-sized grains display ductile fracture. The ductility of the flash-annealed material is recovered significantly due to bimodal grain size distribution in ferrite and the development of a good amount of γ fiber texture components. The major contribution toward recovery of ductility comes from the bimodal grain size distribution in ferrite rather the precipitation of cementite.

  18. Two-step flash light sintering process for enhanced adhesion between copper complex ion/silane ink and a flexible substrate

    Energy Technology Data Exchange (ETDEWEB)

    Jeon, Eun-Beom; Joo, Sung-Jun [Department of Mechanical Convergence Engineering, Hanyang University, Haengdang-dong, Seongdong-gu, Seoul 133-791 (Korea, Republic of); Ahn, Heejoon [Department of Organic and Nano Engineering, Hanyang University, Haengdang-dong, Seongdong-gu, Seoul 133-791 (Korea, Republic of); Kim, Hak-Sung, E-mail: kima@hanyang.ac.kr [Department of Mechanical Convergence Engineering, Hanyang University, Haengdang-dong, Seongdong-gu, Seoul 133-791 (Korea, Republic of); Institute of Nano Science and Technology, Hanyang University, Seoul 133-791 (Korea, Republic of)

    2016-03-31

    A copper complex ion ink (including copper nanoparticles, a copper precursor and a silane coupling agent) was synthesized to enhance the adhesion between the copper pattern and a polyimide (PI) substrate. Oxygen plasma treatment was performed on the polyimide substrate to initiate a chemical reaction between the complex ion ink and the polyimide. Then, a two-step flash light sintering method (consisting of preheating and main sintering) was used to sinter the copper complex ion ink. The copper complex ion patterns were characterized as a function of the weight fraction of silane coupling agent using scanning electron microscopy (SEM), a four-point probe method and adhesion testing. In addition, a bending fatigue test was performed to evaluate the reliability of the conductive copper pattern under cyclic bending. The copper pattern fabricated with copper complex ion ink containing 3 wt% silane coupling agent exhibited the highest adhesion level (5B), the lowest resistivity (7.6 μΩ·cm) and a low resistance change (18%) after the bending fatigue test. The two-step sintering method used to enhance the adhesion between the copper complex ion ink and polyimide substrate was also studied using X-ray diffraction (XRD) and Fourier transform infrared spectroscopy (FT-IR). - Highlights: • The copper complex ion ink with copper nanoparticles and copper precursor was fabricated. • The copper complex ion ink was sintered by two-step flash light sintering method. • The sintered copper pattern exhibited the highest adhesion level (5B). • The resistivity of sintered copper pattern was 7.6 μΩ·cm.

  19. Phase analytical studies of industrial copper smelting slags. Part I: Silicate slags

    Science.gov (United States)

    Rüffler, R.; Dávalos, J.

    1998-12-01

    The pyrometallurgical extraction of copper from sulfide ore concentrates is determined by the behaviour of the associated iron during smelting. Hence, 57Fe Mössbauer spectroscopy is an attractive tool for studying the phases in silicate slags from German and Chilean smelting plants. Other methods used were ore microscopy, electron microprobe analysis, and X-ray powder diffraction.

  20. Flash ionization signature in coherent cyclotron emission from brown dwarfs

    Science.gov (United States)

    Vorgul, I.; Helling, Ch.

    2016-05-01

    Brown dwarfs (BDs) form mineral clouds in their atmospheres, where charged particles can produce large-scale discharges in the form of lightning resulting in substantial sudden increase of local ionization. BDs are observed to emit cyclotron radio emission. We show that signatures of strong transient atmospheric ionization events (flash ionization) can be imprinted on a pre-existing radiation. Detection of such flash ionization events will open investigations into the ionization state and atmospheric dynamics. Such events can also result from explosion shock waves, material outbursts or (volcanic) eruptions. We present an analytical model that describes the modulation of a pre-existing electromagnetic radiation by a time-dependent (flash) conductivity that is characteristic for flash ionization events like lightning. Our conductivity model reproduces the conductivity function derived from observations of terrestrial gamma-ray flashes, and is applicable to astrophysical objects with strong temporal variations in the local ionization, as in planetary atmospheres and protoplanetary discs. We show that the field responds with a characteristic flash-shaped pulse to a conductivity flash of intermediate intensity. More powerful ionization events result in smaller variations of the initial radiation, or in its damping. We show that the characteristic damping of the response field for high-power initial radiation carries information about the ionization flash magnitude and duration. The duration of the pulse amplification or the damping is consistently shorter for larger conductivity variations and can be used to evaluate the intensity of the flash ionization. Our work suggests that cyclotron emission could be probe signals for electrification processes inside BD atmosphere.

  1. Copper hydrometallurgy-current status,preliminary economics,future direction and positioning versus smelting

    Institute of Scientific and Technical Information of China (English)

    J.Peacey; GUO Xian-jian; E.Robles

    2004-01-01

    The heap leaching of oxide copper ores with copper cathode recovery by solvent extraction and electrowinning is now well established as a low-cost method of copper recovery. This technology has recently been applied successfully to mixed oxide and chalcocite ores, notably in Chile at Cerro Colorado, Quebrada Blanca and Zaldivar.Currently, there are significant development efforts underway to try to extend heap leaching to chalcopyrite ores.The success of heap leaching/SX/EW has also led to a revival in the development of hydrometallurgical processes to recover copper from chalcopyrite and other copper concentrates. The current status of copper hydrometallurgy is reviewed and the most commercially attractive potential applications are explored. The advantages and disadvantages of the hydrometallurgical treatment of chalcopyrite concentrates and its preliminary economics are compared with those for the current best practices in copper smelting and refining.

  2. Smelting chlorination method applied to removal of copper from copper slags

    Institute of Scientific and Technical Information of China (English)

    李磊; 王华; 胡建杭

    2015-01-01

    In order to reasonably utilize the iron resources of copper slags, the smelting chlorination process was used to remove copper from copper slags. Higher holding temperature and O2 flow rate are beneficial to increasing copper removal rate. However, the Cu2O mode is formed by the reaction of surplus O2 and CuCl with O2 flow rate increasing over 0.4 L/min, causing CuCl volatilization rate and copper removal rate to decrease. The resulting copper removal rate of 84.34%is obtained under the optimum conditions of holding temperature of 1573 K, residence time of 10 min, CaCl2 addition amount of 0.1 (mass ratio of CaCl2 and the copper slag) and oxygen flow rate of 0.4 L/min. The efficient removal of copper from copper slags through chlorination is feasible.

  3. Efecto de la recirculación de polvo de fundición de cobre de Chile con altos contenidos de impurezas en la distribución de impurezas durante el proceso de fusión

    National Research Council Canada - National Science Library

    Montenegro, V; Sano, H; Fujisawa, T

    2010-01-01

    Usually, dust generated during the copper smelting process by the Teniente Converter and the Flash Smelting Furnaces in Chile, contains high concentrations of copper, zinc, arsenic, antimony and other metals...

  4. Flash droughts in a typical humid and subtropical basin: A case study in the Gan River Basin, China

    Science.gov (United States)

    Zhang, Yuqing; You, Qinglong; Chen, Changchun; Li, Xin

    2017-08-01

    As opposed to traditional drought events, flash droughts evolve rapidly and are characterized by soil moisture deficits. The general lack of high resolution soil moisture and evapotranspiration data makes identifying flash droughts at short-term scales (pentads or weeks) nearly impossible, particularly at the basin scale. In this study, we investigated the spatial patterns, temporal characteristics, and related mechanisms of flash droughts in a humid and subtropical basin (Gan River Basin) in China. The variable infiltration capacity (VIC) model can accurately reflect hydrological processes in the Gan River Basin at daily and monthly time scales; here, flash droughts were determined based on VIC outputs (soil moisture and evapotranspiration) and meteorological observations (maximum temperature and precipitation) during the growing season (March-October) from 1961 to 2013. We classified flash droughts into two categories (heat wave and precipitation deficit flash droughts) based on the formation mechanisms. Heat wave flash droughts are high temperature driven events, high temperatures (heat waves) cause evapotranspiration to increase and soil moisture to decrease rapidly. The main driver of precipitation deficit flash droughts is precipitation deficits, which cause soil moisture to drop and in turn cause evapotranspiration anomalies to decrease and temperature to increase. The northern part of the basin is apparently vulnerable to heat wave flash droughts, whereas precipitation deficit flash droughts tend to occur across the central and southern parts of the basin. Precipitation deficit flash droughts are more common than heat wave flash droughts in general. Both types of flash droughts became significantly more frequent from 1997 to 2013. These increases in both types of flash droughts are likely attributable to climate-related variables such as temperature, precipitation, evapotranspiration, and soil moisture during 1997-2013. As evidenced by our investigation of

  5. Tracking the history of metal smelting in Southeastern Europe throughout the Holocene

    Science.gov (United States)

    Veres, Daniel; Chauvel, Catherine; Longman, Jack; Atlas, Zachary; Haliuc, Aritina; Ersek, Vasile; Tomas; Gabriel, Colin; Gogaltan, Florin; Magyari, Enikö; Schäbitz, Frank

    2016-04-01

    The exploitation of mineral resources, an essential driver of societal development, also induces long lasting impacts on the global ecosystem. Aerosols are released during mining, smelting and combustion (including volatilized elements and chemical aggregates) and they are deposited further away onto peats or lake sediments. The geochemical study of such proxies coupled with isotopic tracing of pollution sources and ore bodies provides an indirect, albeit fundamental view on such past human activities. Here we present newly acquired high-resolution geochemical (major and trace elements), lead isotopic ratios (206-207-208Pb/204Pb) and sedimentological data on several peat records from the Romanian Carpathians that cover a time frame longer than 8000 years, with a special focus over periods with enhanced human impact on the environment, such as the Early Metal Ages, the Antiquity, Medieval and the recent past. We distinguish signatures related to the natural cycling of elements from the anthropogenic contributions due to natural resource exploitation (land, forestry), mining, and smelting activities. Together with existing geological, archaeological, and archaeometric evidences, our results provide the first comprehensive record on the long-term history of metal-use development in the Carpathian region. Through a comparison with records from other parts of Europe we document the existence of strong regional differences in the magnitude, temporal, as well as spatial shifts in our understanding of past emission sources. We therefore show that the existing picture of past pollution load and temporal variability at the European scale is incomplete because it is mainly based on western records without considering the long-term pollution inputs from southeastern Europe, a region with significant mineral endowment and long-lasting human impact on the environment driven by the early rise of agricultural and metal processing activities. The authors acknowledge financial

  6. Flash floods in the Tatra Mountain streams: frequency and triggers.

    Science.gov (United States)

    Ballesteros-Cánovas, J A; Czajka, B; Janecka, K; Lempa, M; Kaczka, R J; Stoffel, M

    2015-04-01

    Flash floods represent a frequently recurring natural phenomenon in the Tatra Mountains. On the northern slopes of the mountain chain, located in Poland, ongoing and expected future changes in climate are thought to further increase the adverse impacts of flash floods. Despite the repeat occurrence of major floods in the densely populated foothills of the Polish Tatras, the headwaters have been characterized by a surprising lack of data, such that any analysis of process variability or hydrometeorological triggers has been largely hampered so far. In this study, dendrogeomorphic techniques have been employed in four poorly-gauged torrential streams of the northern slope of the Tatra Mountains to reconstruct temporal and spatial patterns of past events. Using more than 1100 increment cores of trees injured by past flash floods, we reconstruct 47 events covering the last 148 years and discuss synoptic situations leading to the triggering of flash floods with the existing meteorological and flow gauge data. Tree-ring analyses have allowed highlighting the seasonality of events, providing new insights about potential hydrometeorological triggers as well as a differentiating flash flood activity between catchments. Results of this study could be useful to design future strategies to deal with flash flood risks at the foothills of the Polish Tatras and in the Vistula River catchment.

  7. Flash light sintering of nickel nanoparticles for printed electronics

    Energy Technology Data Exchange (ETDEWEB)

    Park, Sung-Hyeon [School of Mechanical Engineering, Hanyang University, 17 Haengdang-dong, Seongdong-gu, Seoul 133-791 (Korea, Republic of); Kim, Hak-Sung, E-mail: kima@hanyang.ac.kr [School of Mechanical Engineering, Hanyang University, 17 Haengdang-dong, Seongdong-gu, Seoul 133-791 (Korea, Republic of); Institute of Nano Science and Technology, Hanyang University, Seoul 133-79 (Korea, Republic of)

    2014-01-01

    In this paper, a sintering process for nickel nanoparticles using flash light irradiation was investigated for multilayer ceramic capacitors, magnetic devices and printed electronics. The existence of a small amount of 10 nm size nanoparticles in the ink significantly improved the flash light absorption and induced the melting and sintering of the nanoparticles. Due to this phenomenon, uniform diameter nickel nanoparticles (50 nm) could not be sintered, while the nickel nanoparticles with varying diameters (5–500 nm) were sintered by flash light irradiation. In order to acquire high electrical conductivity in the sintered nickel nanoparticles, several flash light sintering parameters such as light energy and pulsed light patterns were optimized. Also, the nickel nano-ink was optimized by changing the weight fractions of organic binder in the ink. - Highlights: • Nickel nanoparticle was sintered by flash light irradiation technique. • The existence of 10 nm size nanoparticles improved the flash light absorption. • The melting temperature of the 10 nm size nanoparticles is significantly decreased. • The only nickel nanoparticles with varying diameters (5–500 nm) were sintered. • Several sintering parameters were optimized for conductivity of nickel nanoparticle.

  8. Advances in flash flood monitoring using UAVs

    Science.gov (United States)

    Perks, Matthew; Russell, Andrew; Large, Andrew

    2016-04-01

    UAVs have the potential to capture information about the earth's surface in dangerous and previously inaccessible locations. Through image acquisition of flash flood events and subsequent object-based analysis, highly dynamic and oft-immeasurable hydraulic phenomenon may be quantified at previously unattainable spatial and temporal resolutions. The potential for this approach to provide valuable information about the hydraulic conditions present during dynamic, high-energy flash floods has until now not been explored. In this paper we adopt a novel approach, utilising the Kande-Lucas-Tomasi (KLT) algorithm to track features present on the water surface which are related to the free-surface velocity. Following the successful tracking of features, a method analogous to the vector correction method has enabled accurate geometric rectification of velocity vectors. Uncertainties associated with the rectification process induced by unsteady camera movements are subsequently explored. Geo-registration errors are relatively stable and occur as a result of persistent residual distortion effects following image correction. The apparent ground movement of immobile control points between measurement intervals ranges from 0.05 - 0.13m. The application of this approach to assess the hydraulic conditions present in Alyth Burn, Scotland during a 1:200 year flash flood resulted in the generation of an average 4.2 measurements/m2 at a rate of 508 measurements/s. Analysis of these vectors provide a rare insight into the complexity of channel-overbank interactions during flash floods. The uncertainty attached to the calculated velocities is relatively low with a spatial average across the area of ± 0.15m/s. Little difference is observed in the uncertainty attached to out-of-bank velocities (± 0.15m/s), and within-channel velocities (± 0.16m/s), illustrating the consistency of the approach.

  9. Thermodynamics Behavior of Titanium for BOF Smelting Bearing Steel

    Institute of Scientific and Technical Information of China (English)

    LIU Yue; WU Wei; LIU Liu; LIU Ming; LI Yang-zhou

    2006-01-01

    When titanium element appears in bearing steel, it is very easy to create titanium nitride inclusion, which reduces the fatigue life of bearing steel. Based on the production data of bearing steel produced by BOF, it is found that the titanium takes its source in bearing steel; the factors affecting titanium content, and the thermodynamics behavior of titanium under smelting condition were studied. The results show that the prime reasons of titanium content increment are the soluble aluminum content and the titanium oxide of slag. The comparison between the experimental data and theoretical ones shows that there is a big declination when the soluble aluminum content of steel is higher, which is caused by the nonequilibrium reaction of slag and steel. The apparent equilibrium distribution coefficient of titanium between slag and steel is obtained by use of experimental data.

  10. Modeling and control of copper loss in smelting slag

    Science.gov (United States)

    Tan, Pengfu

    2011-12-01

    A series of technical improvements have been implemented to address the issue of high copper losses in rotary holding furnace (RHF) slag, which were experienced at the Xstrata Copper Smelter at Mount Isa in 2007 and 2008. The copper losses in smelting slag in the RHF were more than 3% in 2006 and 2007. Thermodynamic models and viscosity models have been applied in the operation of Xstrata Copper Smelter in Australia. The theory of RHF key performance indicators has also been developed to reduce the copper losses in RHF slag. The RHF KPIs Theory has been applied in Mount Isa Copper Smelter. The copper losses in RHF slag dropped from 3.1% in 2007 to 0.76% in April 2009. The average copper loss in RHF slag in 2009 and 2010 was about 0.9%.

  11. Study of Wetting Feature on Refractories for Smelting Reuction Melts With Iron Bath

    Institute of Scientific and Technical Information of China (English)

    LIUQingcai

    1997-01-01

    The wetting feature of smelting reduction melts on the different kinds of refractories is studied in this paper.The results indicate that the activity or concentration of FeO in slag and content of carbon existing in refractory are the important factors affecting on the wetting character,The higher the activity of FeO,the stronger the wetting capacity of slag on refrac-tories ,On the other hand,the higher the crbon content in refrctories,the lower the wetting capacity of melts ,wetting feature of smelting reduction melts is th key factor that affects the corrrosion capacity of melts of smelting reduction on refractory.

  12. Impact of rainfall spatial variability on Flash Flood Forecasting

    Science.gov (United States)

    Douinot, Audrey; Roux, Hélène; Garambois, Pierre-André; Larnier, Kevin

    2014-05-01

    According to the United States National Hazard Statistics database, flooding and flash flooding have caused the largest number of deaths of any weather-related phenomenon over the last 30 years (Flash Flood Guidance Improvement Team, 2003). Like the storms that cause them, flash floods are very variable and non-linear phenomena in time and space, with the result that understanding and anticipating flash flood genesis is far from straightforward. In the U.S., the Flash Flood Guidance (FFG) estimates the average number of inches of rainfall for given durations required to produce flash flooding in the indicated county. In Europe, flash flood often occurred on small catchments (approximately 100 km2) and it has been shown that the spatial variability of rainfall has a great impact on the catchment response (Le Lay and Saulnier, 2007). Therefore, in this study, based on the Flash flood Guidance method, rainfall spatial variability information is introduced in the threshold estimation. As for FFG, the threshold is the number of millimeters of rainfall required to produce a discharge higher than the discharge corresponding to the first level (yellow) warning of the French flood warning service (SCHAPI: Service Central d'Hydrométéorologie et d'Appui à la Prévision des Inondations). The indexes δ1 and δ2 of Zoccatelli et al. (2010), based on the spatial moments of catchment rainfall, are used to characterize the rainfall spatial distribution. Rainfall spatial variability impacts on warning threshold and on hydrological processes are then studied. The spatially distributed hydrological model MARINE (Roux et al., 2011), dedicated to flash flood prediction is forced with synthetic rainfall patterns of different spatial distributions. This allows the determination of a warning threshold diagram: knowing the spatial distribution of the rainfall forecast and therefore the 2 indexes δ1 and δ2, the threshold value is read on the diagram. A warning threshold diagram is

  13. Recovery of iron, carbon and zinc from steel plant waste oxides using the AISI-DOE postcombustion smelting technology

    Energy Technology Data Exchange (ETDEWEB)

    Sarma, B. [Praxair, Inc., Tarrytown, NY (United States); Downing, K.B. [Fluor Daniel, Greenville, SC (United States); Aukrust, E.

    1996-09-01

    This report describes a process to recover steel plant waste oxides to be used in the production of hot metal. The process flowsheet used at the pilot plant. Coal/coke breeze and iron ore pellets/waste oxides are charged into the smelting reactor. The waste oxides are either agglomerated into briquettes (1 inch) using a binder or micro-agglomerated into pellets (1/4 inch) without the use of a binder. The iron oxides dissolve in the slag and are reduced by carbon to produce molten iron. The gangue oxides present in the raw materials report to the slag. Coal charged to the smelter is both the fuel as well as the reductant. Carbon present in the waste oxides is also used as the fuel/reductant resulting in a decrease in the coal requirement. Oxygen is top blown through a central, water-cooled, dual circuit lance. Nitrogen is injected through tuyeres at the bottom of the reactor for stirring purposes. The hot metal and slag produced in the smelting reactor are tapped at regular intervals through a single taphole using a mudgun and drill system. The energy requirements of the process are provided by (i) the combustion of carbon to carbon monoxide, referred to as primary combustion and (ii) the combustion of CO and H{sub 2} to CO{sub 2} and H{sub 2}O, known as postcombustion.

  14. Flash Professional CS5 Digital Classroom

    CERN Document Server

    Gerantabee, Fred

    2011-01-01

    Learn Flash in a flash with this full-color book and video training package! Adobe Flash is used by designers, game programmers, and hobbyists to create interactive Web sites, digital experiences, and mobile content. The latest release of Flash promises exciting new capabilities and this book-and-video training package makes learning the new features of Flash less intimidating. Fifteen self-paced lessons encourage you to discover essential skills and explore new aspects of Flash. The tutorials featured in the videos are each approximately five minutes long and supplement the concepts and topic

  15. Cost-Effective Test Solutions for Smart Card and Other Integrated Flash Applications

    Institute of Scientific and Technical Information of China (English)

    Thomas M. Trexler

    2004-01-01

    @@ From its emergence in the late 1980s as a lower cost alternative to early EEPROM technologies, flash memory has evolved to higher densities and speedsand rapidly growing acceptance in mobile applications.In the process, flash memory devices have placed increased test requirements on manufacturers. Today, as flash device test grows in importance in China, manufacturers face growing pressure for reduced cost-oftest, increased throughput and greater return on investment for test equipment. At the same time, the move to integrated flash packages for contactless smart card applications adds a significant further challenge to manufacturers seeking rapid, low-cost test.

  16. Theoretical investigation of flash vaporisation in a screw expander

    Science.gov (United States)

    Vasuthevan, Hanushan; Brümmer, Andreas

    2017-08-01

    In the present study flash vaporisation of liquid injection in a twin screw expander for a Trilateral Flash Cycle (TFC) is examined theoretically. The TFC process comprises a pressure increase in the working fluid, followed by heating the liquid close to boiling point. The hot liquid is injected into the working chamber of a screw expander. During this process the pressure of the liquid drops below the saturation pressure, while the temperature of the liquid remains virtually constant. Hence the liquid is superheated and in a metastable state. The liquid jet seeks to achieve a stable state in thermodynamic equilibrium and is therefore partially vaporised. This effect is referred to as flash vaporisation. Accordingly, a two-phase mixture, consisting of vapour and liquid, exists in the working chamber. Thermodynamic simulations were carried out using water as the working fluid for representative screw expander geometry. The simulations presented are performed from two different aspects during the filling process of a screw expander. The first case is the vaporisation of the injected liquid in a state of thermodynamic equilibrium, whereby the two-phase mixture is treated entirely as a compressible and homogeneous gas. The second case considers flashing efficiency. It describes the quantity of flashed vapour and consists of a liquid and vapour domain. Both models are compared and analysed with respect to the operational behaviour of a screw expander.

  17. Flashing light in microalgae biotechnology.

    Science.gov (United States)

    Abu-Ghosh, Said; Fixler, Dror; Dubinsky, Zvy; Iluz, David

    2016-03-01

    Flashing light can enhance photosynthesis and improve the quality and quantity of microalgal biomass, as it can increase the products of interest by magnitudes. Therefore, the integration of flashing light effect into microalgal cultivation systems should be considered. However, microalgae require a balanced mix of the light/dark cycle for higher growth rates, and respond to light intensity differently according to the pigments acquired or lost during the growth. This review highlights recently published results on flashing light effect on microalgae and its applications in biotechnology, as well as the recently developed bioreactors designed to fulfill this effect. It also discusses how this knowledge can be applied in selecting the optimal light frequencies and intensities with specific technical properties for increasing biomass production and/or the yield of the chemicals of interest by microalgae belonging to different genera.

  18. Optimization of parameters for MRU desalination flash drum process based on particle size distribution%基于粒度分布的 MRU脱盐闪蒸罐工艺参数优选

    Institute of Scientific and Technical Information of China (English)

    刘康; 贺三; 刘晓明; 徐兆立; 袁宗明

    2016-01-01

    乙二醇再生脱盐装置是深水天然气开发中的核心装置之一,常采用蒸发结晶和重力沉降原理来实现高溶解度盐(如NaCl)的脱除。对脱盐闪蒸罐的主要工艺参数,过去主要从能耗的角度进行优选,只能反映工艺参数对蒸发的影响,难以直接反映对结晶与颗粒沉降分离的影响。从晶体粒度分布的角度出发,利用激光粒度仪研究了温度、压力和停留时间等因素对NaCl在乙二醇溶液中晶体粒度分布的影响规律,并据此优选工艺参数。结果表明,在同等条件下,温度越高,晶体的粒度分布越分散,平均粒度越小;真空度越高,晶体的粒度分布越分散,平均粒度越小;停留时间过长或过短都将导致晶体的平均粒度变小。对所讨论的介质,优选后的工艺参数为:闪蒸温度140℃,压力-80 kPa ,停留时间5 m in。经研制的连续实验装置验证,优选后的参数能实现稳定的沉降分离和脱盐。%Monoethylene glycol regeneration & desalination system is one of key units in deepwater gas development ,often using evaporative crystallization and sedimentation theory to achieve high solubility salt (such as NaCl ) removal . T he main process parameters on the desalting flash tank , mainly optimized from the perspective of energy in the past ,can only show the effects of process parameters on evaporation , but not directly show the effects on the crystallization and particles settling & separation .To study the main process parameters of flash separator as a crystallizer ,the influence of temperature , pressure , and residence time on the crystal size distribution of NaCl in ethylene glycol solution was studied by laser diffraction particle size analyzer .The results showed that under the same conditions ,the higher temperature ,the more dispersive crystal size distribution and the smaller average particle size ;the higher degree of vacuum , the more

  19. Flash Builder building user interaction

    CERN Document Server

    Rocchi, Cesare

    2010-01-01

    Develop a working understanding of events and components, and containers and states so you can build and deploy RIAs in Flex. Work through a demo implementation of a login panel that employs feedback from the server side, to hone your understanding. Use the validators and the debugger to inspect your code execution. Building User Interaction is the second of five articles that will be compiled in the book, Data Visualization with Flash Builder: Designing RIA and AIR Applications with Remote Data Sources. Each full-color article illustrates specific aspects of Flash Builder data visualization

  20. Flash Builder charting and multimedia

    CERN Document Server

    Rocchi, Cesare

    2010-01-01

    Charting and multimedia are two vital tools for data-driven applications. Learn about the main components of the chart library included in Flash Builder, and see how to build and customize widely used charts. Turning your attention to the multimedia capabilities of the Flex framework, you will review the multimedia components built into the Flex library, and learn how to use ActionScript to manipulate video and audio files. Charting and Multimedia is the third of five articles that will be compiled in the book, Data Visualization with Flash Builder: Designing RIA and AIR Applications with Rem

  1. Comparison of rainbow smelt age estimates from fin rays and otoliths

    Science.gov (United States)

    Walsh, M.G.; Maloy, A.P.; O'Brien, T. P.

    2008-01-01

    Rainbow smelt Osmerus mordax, although nonnative, are an important component of the offshore food web in the Laurentian Great Lakes. In Lake Ontario, we estimate ages of rainbow smelt annually to study population dynamics such as year-class strength and age-specific growth and mortality. Since the early 1980s, we have used pectoral fin rays to estimate rainbow smelt ages, but the sectioning and mounting of fin rays are time and labor intensive. Our objective was to assess the feasibility of using otoliths rather than fin rays to estimate rainbow smelt ages. Three readers interpreted the ages of 172 rainbow smelt (60-198 mm total length) based on thin sections of pectoral fin rays, whole otoliths with no preparation, and whole otoliths that had been cleared for 1 month in a 70:30 ethanol : glycerin solution. Bias was lower and precision was greater for fin rays than for otoliths; these results were consistent for comparisons within readers (first and second readings by one individual; three readers were used) and between readers (one reading for each reader within a pair). Both otolith methods appeared to misclassify age-1 rainbow smelt. Fin ray ages had the highest precision and provided the best approximation of age estimates inferred from the Lake Ontario population's length frequency distribution and from our understanding of this population. ?? American Fisheries Society 2008.

  2. Delta smelt: Life history and decline of a once abundant species in the San Francisco Estuary

    Science.gov (United States)

    Moyle, Peter B.; Brown, Larry R.; Durand, John R; Hobbs, James A.

    2016-01-01

    This paper reviews what has been learned about Delta Smelt and its status since the publication of The State of Bay-Delta Science, 2008 (Healey et al. 2008). The Delta Smelt is endemic to the upper San Francisco Estuary. Much of its historic habitat is no longer available and remaining habitat is increasingly unable to sustain the population. As a listed species living in the central node of California’s water supply system, Delta Smelt has been the focus of a large research effort to understand causes of decline and identify ways to recover the species. Since 2008, a remarkable record of innovative research on Delta Smelt has been achieved, which is summarized here. Unfortunately, research has not prevented the smelt’s continued decline, which is the result of multiple, interacting factors. A major driver of decline is change to the Delta ecosystem from water exports, resulting in reduced outflows and high levels of entrainment in the large pumps of the South Delta. Invasions of alien species, encouraged by environmental change, have also played a contributing role in the decline. Severe drought effects have pushed Delta Smelt to record low levels in 2014–2015. The rapid decline of the species and failure of recovery efforts demonstrate an inability to manage the Delta for the “co-equal goals” of maintaining a healthy ecosystem and providing a reliable water supply for Californians. Diverse and substantial management actions are needed to preserve Delta Smelt.

  3. 3D Flash LIDAR Space Laser Project

    Data.gov (United States)

    National Aeronautics and Space Administration — Advanced Scientific Concepts, Inc. (ASC) is a small business that has developed 3D Flash LIDAR systems for space and terrestrial applications. 3D Flash LIDAR is...

  4. Development of Full Automatic Flash Butt Welding with Digital Control

    Institute of Scientific and Technical Information of China (English)

    WANG Rui; SUN Hexu; WANG Hongwen

    2006-01-01

    The hardware and software design of two digital control systems based on 80C196KB MCU for flash butt welder is introduced in this paper. The welding power supply is made of six-phase half-wave rectifier. The welding outer characteristic of welding machine is realized by digital PI algorithm with the voltage close-loop feedback. The flashing curve is finished by electric-hydraulic servo valve .The process control system transfers datum with power supply system by a serial communication interface. The parameters of the control systems are collected by photoelectrical seclusion to avoid the disturbing of the electromagnetism in welding process.

  5. 铜冶炼炉渣缓冷技术研究与生产实践%Copper Smelting Slag Slow Cooling Technology Research and Practice

    Institute of Scientific and Technical Information of China (English)

    王国红

    2014-01-01

    Slow cooling process is widely used to recycle copper from slag in domestic copper smelter, which can improve copper recovery rate and adaptability of smelting furnace to raw material. After slow cooling slag beneficiation, copper concentrates return to the smelting system, tailings is to be as the raw material for cement production. In this article, the slow cooling process of copper smel-ting slag and the main problem in production practice are described, s the reasons are analyzed and solutions are proposed.%国内铜冶炼厂广泛采用缓冷工艺回收炉渣中铜,该工艺可以提高冶炼厂铜回收率和冶炼炉对原料的适应性。缓冷炉渣经过选矿后,铜精矿返回冶炼系统,尾矿作为生产水泥的原料。介绍了铜冶炼炉渣缓冷工艺及生产实践中存在的主要问题,进行了原因分析并提出了解决措施。

  6. Bipolar lightning flashes observed at the Säntis Tower: Do we need to modify the traditional classification?

    Science.gov (United States)

    Azadifar, Mohammad; Rachidi, Farhad; Rubinstein, Marcos; Rakov, Vladimir A.; Paolone, Mario; Pavanello, Davide

    2016-12-01

    We present and discuss current waveforms associated with 13 bipolar lightning flashes recorded at the Säntis Tower during the period from June 2010 to January 2015. During this period, a total of 427 flashes were recorded, of which 13 (3%) were classified as bipolar flashes. The majority of the recorded flashes (10 out of 13) exhibited a polarity reversal during the initial continuous current, therefore belonging to Category I according to the classification proposed by Rakov (2003). Of the three remaining flashes, two were characterized by different polarities of the initial stage current and the following return stroke or strokes (Category II), and one flash involved return strokes of opposite polarity within the same flash (Category III). In Category I bipolar flashes, the polarity reversal is usually assumed to be associated with in-cloud processes. However, two of our 10 Category I flashes appeared to be each a sequence of two upward discharges of opposite polarity, initiated from the tower within tens of milliseconds of each other. This is the first time that such a sequence has been observed from the same tower. We suggest that the traditional classification of bipolar flashes should be modified to distinguish between two types of Category I flashes: those in which the polarity reversal during the initial stage is associated with in-cloud processes (Category Ia) and those in which the polarity reversal is due to initiation of two opposite-polarity leaders from the tower (Category Ib).

  7. 3D flash lidar imager onboard UAV

    Science.gov (United States)

    Zhou, Guoqing; Liu, Yilong; Yang, Jiazhi; Zhang, Rongting; Su, Chengjie; Shi, Yujun; Zhou, Xiang

    2014-11-01

    A new generation of flash LiDAR sensor called GLidar-I is presented in this paper. The GLidar-I has been being developed by Guilin University of Technology in cooperating with the Guilin Institute of Optical Communications. The GLidar-I consists of control and process system, transmitting system and receiving system. Each of components has been designed and implemented. The test, experiments and validation for each component have been conducted. The experimental results demonstrate that the researched and developed GLiDAR-I can effectively measure the distance about 13 m at the accuracy level about 11cm in lab.

  8. Flash CS4: The Missing Manual

    CERN Document Server

    Grover, Chris

    2008-01-01

    Unlock the power of Flash and bring gorgeous animations to life onscreen. Flash CS4: The Missing Manual includes a complete primer on animation, a guided tour of the program's tools and capabilities, lots of new illustrations, and more details on working with video. Beginners will learn to use the software in no time, and experienced Flash designers will improve their skills.

  9. Jaan Toomik ajakirjas Flash Art

    Index Scriptorium Estoniae

    1999-01-01

    Kunstiajakirja "Flash Art" maikuu numbris Ando Keskküla artikkel, mis annab ülevaate J. Toomiku loomingust ja peatub pikemalt tema olulisematel töödel. 10. juunist J. Toomiku isiknäitus Londoni fotograafide galeriis. Eksponeeritud video "Uisutaja"

  10. Ingmar Muusikuse foto Flash Artis

    Index Scriptorium Estoniae

    1999-01-01

    Flash Arti 1999. a. oktoobrinumbris virtuaalse näituse rubriigis Ando Keskküla artikkel radikaalsemast eesti kunstist ja kunstielust postsotsialistlikul ajastul. Illustratsiooniks Liina Siibi fotokompositsioonid, Ingmar Muusikuse foto Raoul Kurvitza, Ene-Liis Semperi ja Kiwa Eesti Panga performance'ist

  11. Ingmar Muusikuse foto Flash Artis

    Index Scriptorium Estoniae

    1999-01-01

    Flash Arti 1999. a. oktoobrinumbris virtuaalse näituse rubriigis Ando Keskküla artikkel radikaalsemast eesti kunstist ja kunstielust postsotsialistlikul ajastul. Illustratsiooniks Liina Siibi fotokompositsioonid, Ingmar Muusikuse foto Raoul Kurvitza, Ene-Liis Semperi ja Kiwa Eesti Panga performance'ist

  12. Jaan Toomik ajakirjas Flash Art

    Index Scriptorium Estoniae

    1999-01-01

    Kunstiajakirja "Flash Art" maikuu numbris Ando Keskküla artikkel, mis annab ülevaate J. Toomiku loomingust ja peatub pikemalt tema olulisematel töödel. 10. juunist J. Toomiku isiknäitus Londoni fotograafide galeriis. Eksponeeritud video "Uisutaja"

  13. Occupational injury surveillance: A study in a metal smelting industry

    Directory of Open Access Journals (Sweden)

    Saha Asim

    2007-01-01

    Full Text Available An investigation of occupational injury was undertaken in a metal smelting industry to examine the occurrence and nature of occupational accidents where analysis of occupational injury records was carried out. At the same time, all the workers were interviewed to collect data in relation to personal and occupational characteristics. With this information, the study aimed to examine the role of different factors in the causation of occupational accidents. High incidence of superficial injuries of limbs due mostly to stepping / striking against objects and overexertion / wrong movements of the workers and the frequent association of handling of small tools with work injuries, observed in this study indicated the role of human error in these accidents and highlighted the necessity of proper safety training of the workers. This study also highlighted the need of elevated safety status during summer months and in evening and night shifts (more so in the second half. Moreover, this study could categorize some high-risk groups e.g. young workers, less-experienced workers, obese workers, workers having smoking / chewing habits etc, who need special attention so far as workplace safety is concerned.

  14. Technogenic magnetic particles in soils as evidence of historical mining and smelting activity: A case of the Brynica River Valley, Poland.

    Science.gov (United States)

    Magiera, Tadeusz; Mendakiewicz, Maria; Szuszkiewicz, Marcin; Jabłońska, Mariola; Chróst, Leszek

    2016-10-01

    In the area of Brynica River basin (Upper Silesia, southern Poland) the exploitation and smelting of iron, silver and lead ores was historically documented since early Middle Ages. First investigations showed that metallurgy industry had a large impact from 9th century (AD) until the Second World War. The aim of the study was to use magnetic prospection to detect traces of past mining and ore smelting in Brynica River Valley located in Upper Silesia (southern Poland). The field screening was performed by measurement magnetic susceptibility (κ) on surface and in vertical profiles and was supported locally by gradiometric measurements. Vertical distribution of magnetic susceptibility values was closely associated with the type of soil use. Historical technogenic magnetic particles resulting from exploitation, processing, and smelting of iron, silver, and lead ores were accumulated in the soil layer at the depth 10 to 25cm. They were represented by sharp-edged particles of slag, coke, as well as various mineralogical forms of iron minerals and aggregates composed of carbon particles, aluminosilicate glass, and single particles of metallic iron. The additional geochemical study in adjacent peat bog supported by radiocarbon dating was also performed. The application of integrated geochemical-magnetic methods to reconstruct the historical accumulation of pollutants in the studied peat bog was effective. The magnetic peak, which was pointed out by magnetic analyses, is consistent with the presence of charcoal and pollution from heavy metals, such as Ag, Cd, Cu, Fe, Pb, or Sn. The results of this work will be helpful for the further study of human's impact on the environment related to the historical and even pre-historical ore exploitation and smelting and also used for better targeting the archeological excavations on such areas.

  15. Observers can reliably identify illusory flashes in the illusory flash paradigm.

    Science.gov (United States)

    van Erp, Jan B F; Philippi, Tom G; Werkhoven, Peter

    2013-04-01

    In the illusory flash paradigm, a single flash may be experienced as two flashes when accompanied by two beeps or taps, and two flashes may be experienced as a single flash when accompanied by one beep or tap. The classic paradigm restricts responses to '1' and '2' (2-AFC), ignoring possible qualitative differences between real and illusory flashes and implicitly assuming that illusory flashes are indistinguishable from real flashes. We added a third response category 'different from that of either 1 or 2 flashes' (3-AFC). Eight naïve and 6 experienced observers responded to 160 real and 160 illusory flash trials. Experienced observers were exposed to 1,200 trials before the experiment but without receiving feedback on their performance. The third response category was used for only 4 % of the real flash trials and for 44 % of the illusory flash trials. Experienced observers did so more often (78 %) than naïve observers (18 %). This shows that observers can reliably identify illusory flashes and indicates that mere exposure to illusory flash trials (without feedback) is enough to detect and classify potential qualitative differences between real and illusory flashes.

  16. Geochemical anomalies of toxic elements and arsenic speciation in airborne particles from Cu mining and smelting activities: influence on air quality.

    Science.gov (United States)

    Sánchez de la Campa, Ana M; Sánchez-Rodas, Daniel; González Castanedo, Yolanda; de la Rosa, Jesús D

    2015-06-30

    A characterization of chemical composition and source contribution of PM10 in three representative environments of southwest Spain related to mining activities (mineral extraction, mining waste and Cu-smelting) has been performed. A study of geochemical anomalies was conducted in the samples collected at the three stations between July 2012 and October 2013. The influence of Cu-smelting processes was compared to other mining activities, where common tracers were identified. The Cu and As concentrations in the study area are higher than in other rural and urban stations of Spain, in which geochemical anomalies of As, Se, Bi, Cd, and Pb have been reported. The results of source contribution showed similar geochemical signatures in the industrial and mining factors. However, the contribution to PM10 is different according to the type of industrial activity. These results have been confirmed performing an arsenic speciation analysis of the PM10 samples, in which the mean extraction efficiency of arsenic depended on the origin of the samples. These finding indicate that the atmospheric particulate matter emitted from Cu-smelting has a high residence time in the atmosphere. This indicates that the Cu-smelter can impact areas of high ecological interest and considered as clean air.

  17. Size-Resolved Dust and Aerosol Contaminants Associated with Copper and Lead Smelting Emissions: Implications for Emissions Management and Human Health

    Science.gov (United States)

    Csavina, Janae; Taylor, Mark P.; Félix, Omar; Rine, Kyle P.; Sáez, A. Eduardo; Betterton, Eric A.

    2014-01-01

    Mining operations, including crushing, grinding, smelting, refining, and tailings management, are a significant source of airborne metal and metalloid contaminants such as As, Pb and other potentially toxic elements. In this work, we show that size-resolved concentrations of As and Pb generally follow a bimodal distribution with the majority of contaminants in the fine size fraction (< 1 μm) around mining activities that include smelting operations at various sites in Australia and Arizona. This evidence suggests that contaminated fine particles (< 1 μm) are the result of vapor condensation and coagulation from smelting operations while coarse particles are most likely the result of windblown dust from contaminated mine tailings and fugitive emissions from crushing and grinding activities. These results on the size distribution of contaminants around mining operations are reported to demonstrate the ubiquitous nature of this phenomenon so that more effective emissions management and practices that minimize health risks associated with metal extraction and processing can be developed. PMID:24995641

  18. Flash (Ultra-Rapid) Spark-Plasma Sintering of Silicon Carbide

    Science.gov (United States)

    Olevsky, Eugene A.; Rolfing, Stephen M.; Maximenko, Andrey L.

    2016-09-01

    A new ultra-rapid process of flash spark plasma sintering is developed. The idea of flash spark plasma sintering (or flash hot pressing - FHP) stems from the conducted theoretical analysis of the role of thermal runaway phenomena for material processing by flash sintering. The major purpose of the present study is to theoretically analyze the thermal runaway nature of flash sintering and to experimentally address the challenge of uncontrollable thermal conditions by the stabilization of the flash sintering process through the application of the external pressure. The effectiveness of the developed FHP technique is demonstrated by the few seconds-long consolidation of SiC powder in an industrial spark plasma sintering device. Specially designed sacrificial dies heat the pre-compacted SiC powder specimens to a critical temperature before applying any voltage to the powder volume and allowing the electrode-punches of the SPS device setup to contact the specimens and pass electric current through them under elevated temperatures. The experimental results demonstrate that flash sintering phenomena can be realized using conventional SPS devices. The usage of hybrid heating SPS devices is pointed out as the mainstream direction for the future studies and utilization of the new flash hot pressing (ultra-rapid spark plasma sintering) technique.

  19. Foundation Flash CS4 for Designers

    CERN Document Server

    Green, Tom

    2008-01-01

    In this book, you'll learn:* How to create effective animations using the new Motion Editor and animation tools * How to use the new 3D features to animate objects in 3D space * Best-practice tips and techniques from some of the top Flash practitioners on the planet * How to create captioned video and full-screen video, and deploy HD video using Flash * Techniques for using the Flash UI components as well as XML documents to create stunning,interactive presentations If you're a Flash designer looking for a solid overview of Flash CS4, this book is for you. Through the use of solid and practica

  20. uFlip: Understanding Flash IO Patterns

    DEFF Research Database (Denmark)

    Bouganim, Luc; Jonsson, Bjørn; Bonnet, Philippe

    2009-01-01

    want to establish what kind of IOs should be favored (or avoided) when designing algorithms and architectures for flash-based systems. In this paper, we focus on flash IO patterns, that capture relevant distribution of IOs in time and space, and our goal is to quantify their performance. We define u......FLIP, a benchmark for measuring the response time of flash IO patterns. We also present a benchmarking methodology which takes into account the particular characteristics of flash devices. Finally, we present the results obtained by measuring eleven flash devices, and derive a set of design hints that should drive...

  1. Novel approach for low-cost muzzle flash detection system

    Science.gov (United States)

    Voskoboinik, Asher

    2008-04-01

    A low-cost muzzle flash detection based on CMOS sensor technology is proposed. This low-cost technology makes it possible to detect various transient events with characteristic times between dozens of microseconds up to dozens of milliseconds while sophisticated algorithms successfully separate them from false alarms by utilizing differences in geometrical characteristics and/or temporal signatures. The proposed system consists of off-the-shelf smart CMOS cameras with built-in signal and image processing capabilities for pre-processing together with allocated memory for storing a buffer of images for further post-processing. Such a sensor does not require sending giant amounts of raw data to a real-time processing unit but provides all calculations in-situ where processing results are the output of the sensor. This patented CMOS muzzle flash detection concept exhibits high-performance detection capability with very low false-alarm rates. It was found that most false-alarms due to sun glints are from sources at distances of 500-700 meters from the sensor and can be distinguished by time examination techniques from muzzle flash signals. This will enable to eliminate up to 80% of falsealarms due to sun specular reflections in the battle field. Additional effort to distinguish sun glints from suspected muzzle flash signal is made by optimization of the spectral band in Near-IR region. The proposed system can be used for muzzle detection of small arms, missiles and rockets and other military applications.

  2. Nanocrystalline magnetic materials obtained by flash annealing

    Directory of Open Access Journals (Sweden)

    R.K. Murakami

    1999-04-01

    Full Text Available The aim of the present work was to produce enhanced-remanence nanocrystalline magnetic material by crystallizing amorphous or partially amorphous Pr4.5Fe77B18.5 alloys by the flash annealing process, also known as the dc-Joule heating process, and to determine the optimal conditions for obtaining good magnetic coupling between the magnetic phases present in this material. Ribbons of Pr4.5Fe77B18.5 were produced by melt spinning and then annealed for 10-30 s at temperatures 500 - 640 °C by passing current through the sample to develop the enhanced-remanence nanocrystalline magnetic material. These materials were studied by X-ray diffraction, differential thermal analysis and magnetic measurements. Coercivity increases of up to 15% were systematically observed in relation to furnace-annealed material. Two different samples were carefully examined: (i a sample annealed at 600 °C which showed the highest coercive field Hc and remanence ratio Mr/Ms and (ii a sample annealed at 520 °C which showed phase separation in the second quadrant demagnetization curve. Our results are in agreement with other studies which show that flash annealing improves the magnetic properties of some amorphous ferromagnetic ribbons.

  3. Document Flash Thermography

    OpenAIRE

    Larsen, Cory A.

    2011-01-01

    This thesis presents the application of ash thermography techniques to the analysis of documents. The motivation for this research is to develop the ability to non-destructively reveal covered writings in archaeological artifacts such as the Codex Selden or Egyptian car- tonnage. Current common signal processing techniques are evaluated for their effectiveness in enhancing subsurface writings found within a set of test documents. These processing techniques include: false colorization, contra...

  4. 氧压浸出炼锌渣处理工艺研究%The Treatment Technology on Waste Residues from Zinc Smelting byOxygen Pressure Acid Leaching

    Institute of Scientific and Technical Information of China (English)

    陈锋

    2016-01-01

    According to the harmless treatment of waste residues and the comprehensive recovery of valuable metal which are produced by oxygen pressure acid leaching of zinc smelting, the analysis are carried out for waste residues from zinc smelting by oxygen pressure acid leaching technology, such as the rotary kiln volatilization, rotary kiln reducing roasting, oxygen-enriched bath smelting, oxygen-enriched stock column smelting. Thereby the treatment process and process flow, technology parameters, economic indicators for the different waste residues are proposed.%针对氧压浸出炼锌产出的废渣进行无害化处理和有价金属综合回收问题,对回转窑挥发、回转窑还原焙烧、富氧熔池熔炼、富氧料柱熔炼处理氧压浸出炼锌渣工艺技术进行分析研究,提出不同情况的废渣可以采用的处理工艺及其工艺流程、技术参数、经济指标等.

  5. Differentiation of debris-flow and flash-flood deposits: implications for paleoflood investigations

    Science.gov (United States)

    Waythomas, Christopher F.; Jarrett, Robert D.; ,

    1993-01-01

    Debris flows and flash floods are common geomorphic processes in the Colorado Rocky Mountain Front Range and foothills. Usually, debris flows and flash floods are associated with excess summer rainfall or snowmelt, in areas were unconsolidated surficial deposits are relatively thick and slopes are steep. In the Front Range and foothills, flash flooding is limited to areas below about 2300m whereas, debris flow activity is common throughout the foothill and alpine zones and is not necessarily elevation limited. Because flash floods and debris flows transport large quantities of bouldery sediment, the resulting deposits appear somewhat similar even though such deposits were produced by different processes. Discharge estimates based on debris-flow deposits interpreted as flash-flood deposits have large errors because techniques for discharge retrodiction were developed for water floods with negligible sediment concentrations. Criteria for differentiating between debris-flow and flash-flood deposits are most useful for deposits that are fresh and well-exposed. However, with the passage of time, both debris-flow and flash-flood deposits become modified by the combined effects of weathering, colluviation, changes in surface morphology, and in some instances removal of interstitial sediment. As a result, some of the physical characteristics of the deposits become more alike. Criteria especially applicable to older deposits are needed. We differentiate flash-flood from debris-flow and other deposits using clast fabric measurements and other morphologic and sedimentologic techniques (e.g., deposit morphology, clast lithology, particle size and shape, geomorphic setting).

  6. Flashing Slurry Releases

    Energy Technology Data Exchange (ETDEWEB)

    Schmitt, Bruce E.; Young, Jonathan

    2007-03-14

    The Hanford K Basin Closure Project involves the retrieval, transfer and processing of radioactive contaminated slurries containing partially corroded spent nuclear fuel from the K Basin spent fuel pools. The spent fuel is primarily metallic fuel from the operation of the Hanford reactors. The Sludge Treatment Project is being designed to treat and package this material in preparation for ultimate disposal. The processing of the contaminated slurries includes further corrosion of the remaining uncorroded uranium metal in a large heated vessel to form a more stable metal oxide for packaging and storage.

  7. Temporal Binding Window of the Sound-Induced Flash Illusion in Amblyopia.

    Science.gov (United States)

    Narinesingh, Cindy; Goltz, Herbert C; Wong, Agnes M F

    2017-03-01

    Amblyopia is a neurodevelopmental visual disorder caused by abnormal visual experience in childhood. In addition to known visual deficits, there is evidence for changes in audiovisual integration in amblyopia using explicit tasks. We examined audiovisual integration in amblyopia using an implicit task that is more relevant in a real-world context. A total of 11 participants with amblyopia and 16 controls were tested binocularly and monocularly on the sound-induced flash illusion, in which flashes and beeps are presented concurrently and the perceived number of flashes is influenced by the number of beeps. The task used 1 to 2 rapid peripheral flashes presented with 0 to 2 beeps, at 5 stimulus onset asynchronies, that is, beep (-200 milliseconds, -100 milliseconds) or flash leading (100 milliseconds, 200 milliseconds) or simultaneous (0 milliseconds). Participants reported the number of perceived flashes. Susceptibility was indicated by a "2 flashes" response to "fission" (1 flash, 2 beeps) or "1 flash" to "fusion" (2 flashes, 1 beep). For fission with the beep leading during binocular viewing, controls showed an expected decrease in illusion strength as stimulus onset asynchronies increased, whereas the illusion strength remained constant in participants with amblyopia, indicating a wider temporal binding window in amblyopia (P = 0.007). For fusion, participants with amblyopia showed reduced illusion strength during amblyopic eye viewing (P = 0.044) with the flash leading. Amblyopia is associated with the widening of the temporal binding window, specifically for fission when viewing binocularly with the beep leading. This suggests a developmental adaptation to delayed amblyopic eye visual processing to optimize audiovisual integration.

  8. 铜冶炼行业节能减排先进适用技术评估方法研究%Study on Evaluation Method of Advanced and Appropriate Technologies for Energy Saving and Emission Reduction of Copper Smelting Industry

    Institute of Scientific and Technical Information of China (English)

    赵吝加; 曾维华; 许乃中; 温宗国

    2012-01-01

    针对目前国内环境技术评估以专家定性判断为主、缺乏定量技术评估手段的现状,通过设置节能减排先进适用技术指标体系、确定指标权重、构建评估因素集及其隶属函数等过程,建立定性与定量方法相结合的基于层次分析和模糊综合评估的铜冶炼行业节能减排先进适用技术评估方法,综合评估铜冶炼技术.应用该方法,从闪速熔炼、富氧侧吹熔池熔炼、艾萨/奥斯麦特熔炼、氧气底吹熔炼、白银炼铜、诺兰达炼铜等6项技术中,筛选出前4种作为铜冶炼行业重点推广的节能减排先进适用技术.%To improve the current practice of environmental technologies evaluation through experts' qualitative estimate and address the lack of quantitative evaluation methods, an qualitative and quantitative evaluation method, based on AHP and Fuzzy comprehensive evaluation, of advanced and appropriate technologies for energy saving and emission reduction of copper smelting industry was established including the setting of an indicator system of energy saving and emission reduction , determining the indicator weight factor, and structuring the evaluation factors set and its membership function. With this evaluation method, top four of six technologies including Flash Smelting, Oxygen Enrichment Side Blowing Bath Melting, Isasmelt/Ausmelt Smelting, Oxygen Bottom Blowing Smelting, Baiyin Copper Smelting and Noranda Copper Smelting, are generalized as the advanced and appropriate technologies for energy saving and emission reduction of copper smelting industry.

  9. Study on Apparent Kinetic Prediction Model of the Smelting Reduction Based on the Time-Series

    Directory of Open Access Journals (Sweden)

    Guo-feng Fan

    2012-01-01

    Full Text Available A series of direct smelting reduction experiment has been carried out with high phosphorous iron ore of the different bases by thermogravimetric analyzer. The derivative thermogravimetric (DTG data have been obtained from the experiments. One-step forward local weighted linear (LWL method , one of the most suitable ways of predicting chaotic time-series methods which focus on the errors, is used to predict DTG. In the meanwhile, empirical mode decomposition-autoregressive (EMD-AR, a data mining technique in signal processing, is also used to predict DTG. The results show that (1 EMD-AR(4 is the most appropriate and its error is smaller than the former; (2 root mean square error (RMSE has decreased about two-thirds; (3 standardized root mean square error (NMSE has decreased in an order of magnitude. Finally in this paper, EMD-AR method has been improved by golden section weighting; its error would be smaller than before. Therefore, the improved EMD-AR model is a promising alternative for apparent reaction rate (DTG. The analytical results have been an important reference in the field of industrial control.

  10. Arsenic Speciation in Wastes Resulting From Pressure Oxidation, Roasting and Smelting

    Energy Technology Data Exchange (ETDEWEB)

    Paktunc, D. (CCM)

    2010-11-01

    Arsenic commonly occurs in elevated concentrations in some gold and base-metal deposits. Mining and metallurgical processing of gold and base-metal ores results in solid wastes, effluents, and air emissions containing high concentrations of arsenic. Such wastes form an important source of anthropogenic arsenic in the environment. The nature and occurrence of arsenic in solid wastes are complex and highly variable. A combination of microanalytical tools and techniques including XAFS were used to determine the form and speciation of arsenic in wastes resulting from pressure oxidation, roasting and smelting, and impacted soil. As K-edge and Fe K-edge XAFS analyses of the pressure oxidation residues indicate that arsenic in tetrahedral coordination is corner-linked to 5 to 6 FeO{sub 6} octahedra that are edge- and perhaps face-sharing. During roasting of refractory gold ores, oxidation of As to As{sub 2}O{sub 5} species may be incomplete, which is detrimental to not only gold recovery but also the tailings management options. As K-edge XANES spectra indicate that more than one-third of the arsenic released from a copper smelter stack is composed of As{sup 3+} species. Most likely arsenic species in the smelter-impacted soil include arsenolite, goethite with adsorbed As{sup 5+}, monomethylarsonic acidm, and tetramethylarsonium iodide.

  11. Thermodynamic Properties of Lead Oxide in a Mixture of Stainless Steelmaking and Nonferrous Smelting Slags

    Science.gov (United States)

    Maruoka, Nobuhiro; Ueda, Shigeru; Shibata, Hiroyuki; Yamaguchi, Katsunori; Kitamura, Shin-ya

    2012-06-01

    In our previous paper, a slag modification process involving the mixing of stainless steelmaking and nonferrous smelting slags was proposed for preventing the disintegration of the stainless steelmaking slag. In order to use this method, the behavior of heavy metals especially PbO contained in the nonferrous slag has to be assessed. In the present study, the activity coefficient of PbO in CaO-SiO2-FetO-Al2O3-MgO and CaO-SiO2-FetO slags saturated with iron was measured at 1673 K. The results showed that the activity coefficient of PbO increased with basicity and had a maximum value when the basicity was approximately 1.0. The equilibrium PbO content in the modified slag had a minimum value that corresponded to a mixing ratio of 0.6. The trend was similar to the change in the removal ratio of PbO observed in the previous study. Therefore, the change in the oxygen potential and the change in the activity coefficient of PbO can be considered the cause of this trend.

  12. Immobilisation of lead smelting slag within spent aluminate-fly ash based geopolymers.

    Science.gov (United States)

    Ogundiran, M B; Nugteren, H W; Witkamp, G J

    2013-03-15

    This study presents the solidification/stabilisation and immobilisation of lead smelting slag (LSS) by its incorporation in coal fly ash - blast furnace slag based geopolymers. It also explores the use of a spent aluminium etching solution (AES) as geopolymer activator instead of the commonly used silicate solutions. The compressive strength of the geopolymers produced with the AES was lower than when applying a K-silicate solution as activator (100MPa versus 80MPa after 28 days). Compressive strength was not affected when up to 10% of the FA was replaced by LSS. NEN 12457-4, TCLP, SPLP and NEN 7375 leaching tests indicated that mobile Pb from LSS was highly immobilised. The diffusion leaching test NEN 7375 revealed exceeding of the Dutch Soil Quality Regulation threshold limits only for Se and Sb. On the condition that the remaining excess leaching can be reduced by further refinement of the mixture recipes, the proposed process will have the potential of producing waste-based construction materials that may be applied under controlled conditions in specific situations.

  13. Primary Phases and Natural Weathering of Smelting Slag at an Abandoned Mine Site in Southwest Japan

    Directory of Open Access Journals (Sweden)

    Yuri Sueoka

    2013-12-01

    Full Text Available Artisanal metallurgical slag produced more than 50 years ago at a mine site in southwest Japan is rich in toxic metals and metalloids. Some of the slag remains on a waste dump and could contaminate the surrounding area through the dissolution of heavy metals and metalloids during weathering. To assess this risk, this study has investigated the behavior of the toxic elements in the smelting slag during weathering. Most of the potentially toxic elements are contained in willemite and/or matte drops. Maximum metal and metalloid concentrations in the slag are 28.1 wt % Fe, 22.7 wt % Zn, 1.63 wt % Cu, 3450 mg/kg Sn, 826 mg/kg Pb, 780 mg/kg As, and 116 mg/kg Cd. Zn is mainly contained in willemite, whereas other metals and metalloids are mainly concentrated in matte drops. The willemite and matte drops are converted to Fe-hydroxides during weathering, indicating that potentially toxic metals and metalloids contained in these phases are released by weathering processes. Therefore, weathering of the artisanal metallurgical slag, containing large amounts of willemite and matte drops, may pollute the surrounding environment.

  14. Multi-stage flash degaser

    Science.gov (United States)

    Rapier, Pascal M.

    1982-01-01

    A multi-stage flash degaser (18) is incorporated in an energy conversion system (10) having a direct-contact, binary-fluid heat exchanger to remove essentially all of the noncondensable gases from geothermal brine ahead of the direct-contact binary-fluid heat exchanger (22) in order that the heat exchanger (22) and a turbine (48) and condenser (32) of the system (10) can operate at optimal efficiency.

  15. Trajectory Codes for Flash Memory

    CERN Document Server

    Anxiao,; Langberg, Michael; Schwartz, Moshe; Bruck, Jehoshua

    2010-01-01

    Flash memory is well-known for its inherent asymmetry: the flash-cell charge levels are easy to increase but are hard to decrease. In a general rewriting model, the stored data changes its value with certain patterns. The patterns of data updates are determined by the data structure and the application, and are independent of the constraints imposed by the storage medium. Thus, an appropriate coding scheme is needed so that the data changes can be updated and stored efficiently under the storage-medium's constraints. In this paper, we define the general rewriting problem using a graph model. It extends many known rewriting models such as floating codes, WOM codes, buffer codes, etc. We present a new rewriting scheme for flash memories, called the trajectory code, for rewriting the stored data as many times as possible without block erasures. We prove that the trajectory code is asymptotically optimal in a wide range of scenarios. We also present randomized rewriting codes optimized for expected performance (g...

  16. Annual Report Ant Smelt 2010: A changing role for smelt Osmerus eperlanus in the Lake IJsselmeer and Lake Markermeer foodweb? Climate- and nutrient-induced changes in ecoystem functioning

    NARCIS (Netherlands)

    Graaf, de M.; Keller, A.M.

    2010-01-01

    The smelt project is part of a larger research project that aims at generating, exploring and testing different possible explanations for the observed Autonomous Negative Trends (ANT) in water fowl in Lake Markermeer and Lake IJsselmeer. The smelt populations in both lakes have been in severe declin

  17. Flash Vacuum Pyrolysis - Techniques and Reactions.

    Science.gov (United States)

    Wentrup, Curt

    2017-07-04

    While pyrolysis reactions have been performed since ancient times and been crucial for the invention of several technologies, the methodology now commonly known as flash vacuum pyrolysis, FVP (or flash vacuum thermolysis, FVT) had its early beginnings in the 1940s and1950s, mainly through mass spectrometric detection of pyrolytically formed free radicals. In the 1960s many organic chemists started performing FVP experiments with the purpose of isolating new and interesting compounds and understanding pyrolysis processes. Meanwhile, many different types of apparatus and techniques have been developed, and it is the purpose of this review to present the most important methods as well as a survey of typical reactions and observations that can be achieved with the various techniques. This includes preparative FVP, chemical trapping reactions, matrix isolation and low temperature spectroscopy of reactive intermediates and unstable molecules, the use of online mass, photoelectron, microwave and millimeterwave spectroscopies, gas-phase laser pyrolysis, pulsed pyrolysis with supersonic jet expansion, very low pressure pyrolysis for kinetic investigations, solution-spray and falling-solid FVP for involatile compounds, and pyrolysis over solid supports and reagents. Moreover, the combination of FVP with matrix isolation and photochemistry is a powerful tool for investigations of reaction mechanism. © 2017 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  18. Honeywell optical investigations on FLASH program

    Science.gov (United States)

    O'Rourke, Ken; Peterson, Eric; Yount, Larry

    1995-05-01

    The increasing performance and reduction of life cycle cost requirements placed on commercial and military transport aircraft are resulting in more complex, highly integrated aircraft control and management systems. The use of fiber optic data transmission media can make significant contributions in achieving these performance and cost goals. The Honeywell portion of Task 2A on the Fly-by-Light Advanced System Hardware (FLASH) program is evaluating a Primary Flight Control System (PFCS) using pilot and copilot inputs from Active Hand Controllers (AHC) which are optically linked to the primary flight Control Computers (PFCC). Customer involvement is an important element of the Task 2A activity. Establishing customer requirements and perspectives on productization of systems developed under FLASH are key to future product success. The Honeywell elements of the PFCS demonstrator provide a command path that is optically interfaced from crew inputs to commands of distributed, smart actuation subsystems commands. Optical communication architectures are implemented using several protocols including the new AS-1773A 20 Mbps data bus standard. The interconnecting fiber optic cable plant is provided by our Task 1A teammate McDonnell Douglas Aerospace (West). Fiber optic cable plant fabrication uses processed, tools and materials reflecting necessary advances in manufacturing required to make fly-by-light avionics systems marketable.

  19. Work Process-oriented Practice Teaching Reform — FLASH Technology Courses, For Example%基于工作过程导向的实践教学改革研究——以FLASH技术课程为例

    Institute of Scientific and Technical Information of China (English)

    蒋燕

    2013-01-01

    国家教育部在关于推进高等职业教育改革创新引领职业教育科学发展的若干意见中指出,高等职业教育人才培养中要改革培养模式,增强学生可持续发展能力,要把现代企业优秀文化理念融入人才培养全过程,强化学生职业道德和职业精神培养.该文主要以Flash技术课程为例,分析了以工作过程为导向从教学目标定位、重组教学内容、转变教学方式、调整考核评定、实践教学实施的保障等方面入手的教学改革研究.%National Ministry of Education, pointed out in a number of opinions on the promotion of vocational education re?form and innovation to lead the development of vocational education in science, to reform the personnel training in vocational education training mode to enhance students' capacity for sustainable development, it is necessary the outstanding cultural ideas of the modern enterprise financialthe whole process into personnel training, strengthening students' professional ethics and profes?sionalism training. In this paper, Flash technology courses, for example, the analysis of the work process-oriented teaching target?ing, recombinant teaching content, change teaching methods to adjust for the evaluation, and implementation of practice teach?ing security aspects of teaching reform research.

  20. FLASH2: Operation, beamlines, and photon diagnostics

    Energy Technology Data Exchange (ETDEWEB)

    Plönjes, Elke, E-mail: elke.ploenjes@desy.de; Faatz, Bart; Kuhlmann, Marion; Treusch, Rolf [Deutsches Elektronen-Synchrotron DESY, Notkestr. 85, 22607 Hamburg (Germany)

    2016-07-27

    FLASH2, a major extension of the soft X-ray free-electron laser FLASH at DESY, turns FLASH into a multi-user FEL facility. A new undulator line is located in a separate accelerator tunnel and driven additionally by the FLASH linear accelerator. First lasing of FLASH2 was achieved in August 2014 with simultaneous user operation at FLASH1. The new FLASH2 experimental hall offers space for up to six experimental end stations, some of which will be installed permanently. The wide wavelength range spans from 4-60 nm and 0.8 nm in the 5{sup th} harmonic and in the future deep into the water window in the fundamental. While this is of high interest to users, it is challenging from the beamline instrumentation point of view. Online diagnostics - which are mostly pulse resolved - for beam intensity, position, wavelength, wave front, and pulse length have been to a large extent developed at FLASH(1) and have now been optimized for FLASH2. Pump-probe facilities for XUV-XUV, XUV optical and XUV-THz experiments will complete the FLASH2 user facility.

  1. Design of 6-Bit Flash Analog to Digital Converter Using Variable Switching Voltage CMOS Comparator

    Directory of Open Access Journals (Sweden)

    Gulrej Ahmed

    2014-04-01

    Full Text Available This paper presents the design of 6-bit flash analog to digital Converter (ADC using the new variable switching voltage (VSV comparator. In general, Flash ADCs attain the highest conversion speed at the cost of high power consumption. By using the new VSV comparator, the designed 6-bit Flash ADC exhibits significant improvement in terms of power and speed of previously reported Flash ADCs. The simulation result shows that the converter consumes peak power 2.1 mW from a 1.2 V supply and achieves the speed of 1 GHz in a 65nm standard CMOS process. The measurement of maximum differential and integral nonlinearities (DNL and INL of the Flash ADC are 0.3 LSB and 0.6 LSB respectively.

  2. Technogenic magnetic particles in soils as evidence of historical mining and smelting activity: A case of the Brynica River Valley, Poland

    Energy Technology Data Exchange (ETDEWEB)

    Magiera, Tadeusz, E-mail: tadeusz.magiera@ipis.zabrze.pl [Institute of Environmental Engineering, Polish Academy of Sciences, Skłodowskiej-Curie 34, Zabrze (Poland); Mendakiewicz, Maria; Szuszkiewicz, Marcin [Institute of Environmental Engineering, Polish Academy of Sciences, Skłodowskiej-Curie 34, Zabrze (Poland); Jabłońska, Mariola [Department of Geochemistry, Mineralogy and Petrology, Faculty of Earth Sciences, University of Silesia, Sosnowiec (Poland); Chróst, Leszek [Laboratory for Ecological Research, Ekopomiar, Gliwice (Poland)

    2016-10-01

    In the area of Brynica River basin (Upper Silesia, southern Poland) the exploitation and smelting of iron, silver and lead ores was historically documented since early Middle Ages. First investigations showed that metallurgy industry had a large impact from 9th century (AD) until the Second World War. The aim of the study was to use magnetic prospection to detect traces of past mining and ore smelting in Brynica River Valley located in Upper Silesia (southern Poland). The field screening was performed by measurement magnetic susceptibility (κ) on surface and in vertical profiles and was supported locally by gradiometric measurements. Vertical distribution of magnetic susceptibility values was closely associated with the type of soil use. Historical technogenic magnetic particles resulting from exploitation, processing, and smelting of iron, silver, and lead ores were accumulated in the soil layer at the depth 10 to 25 cm. They were represented by sharp-edged particles of slag, coke, as well as various mineralogical forms of iron minerals and aggregates composed of carbon particles, aluminosilicate glass, and single particles of metallic iron. The additional geochemical study in adjacent peat bog supported by radiocarbon dating was also performed. The application of integrated geochemical-magnetic methods to reconstruct the historical accumulation of pollutants in the studied peat bog was effective. The magnetic peak, which was pointed out by magnetic analyses, is consistent with the presence of charcoal and pollution from heavy metals, such as Ag, Cd, Cu, Fe, Pb, or Sn. The results of this work will be helpful for the further study of human's impact on the environment related to the historical and even pre-historical ore exploitation and smelting and also used for better targeting the archeological excavations on such areas. - Highlights: • Due to ferrimagnetic properties of historical slags magnetic prospection is an efficient tool for they localization.

  3. Flash flood hazard mapping: a pilot case study in Xiapu River Basin, China

    Directory of Open Access Journals (Sweden)

    Da-wei Zhang

    2015-07-01

    Full Text Available Flash flood hazard mapping is a supporting component of non-structural measures for flash flood prevention. Pilot case studies are necessary to develop more practicable methods for the technical support systems of flash flood hazard mapping. In this study, the headwater catchment of the Xiapu River Basin in central China was selected as a pilot study area for flash flood hazard mapping. A conceptual distributed hydrological model was developed for flood calculation based on the framework of the Xinanjiang model, which is widely used in humid and semi-humid regions in China. The developed model employs the geomorphological unit hydrograph method, which is extremely valuable when simulating the overland flow process in ungauged catchments, as compared with the original Xinanjiang model. The model was tested in the pilot study area, and the results agree with the measured data on the whole. After calibration and validation, the model is shown to be a useful tool for flash flood calculation. A practicable method for flash flood hazard mapping using the calculated peak discharge and digital elevation model data was presented, and three levels of flood hazards were classified. The resulting flash flood hazard maps indicate that the method successfully predicts the spatial distribution of flash flood hazards, and it can meet the current requirements in China.

  4. Smelting reduction of MgO in molten slag by liquid ferrosilicon

    Energy Technology Data Exchange (ETDEWEB)

    Tang, Q.; Gao, J.; Chen, X.; Wei, X.

    2016-10-01

    The smelting reduction of magnesium oxide was researched in this paper. The effect of molten slag composition and reduction temperature on percent reduction of magnesium oxide were discussed, and kinetics of smelting reduction of magnesium oxide in molten slag was studied. The results showed that the reduction extent of magnesium oxide increased by increasing either one of the following factors: the initial mass ratio of Al{sub 2}O{sub 3}/SiO{sub 2}, the addition of CaF{sub 2}, the initial molar ratio of Si/2MgO, and reaction temperature. The overall smelting reduction was controlled by mass transfer in slag with an apparent activation energy 586 kJ mol{sup -}1. (Author)

  5. Xinjiang Xinxin Mining Starts to Work on a 10,O00-ton Nickel-smelting Technological Upgrading Project

    Institute of Scientific and Technical Information of China (English)

    2008-01-01

    <正>In October,Xinjiang Xinxin Mining Industry Co.,Ltd.started to work on a 10,000-ton nickel-smelting technological upgrading project at the Kalatongke copper nickel ore in Fuyun County.The technological upgrading project for 10,000-ton nickel-smelting operations that

  6. Preparation of titanium feedstock from Minnesota ilmenite by smelting and sulfation-leaching

    Energy Technology Data Exchange (ETDEWEB)

    Nafziger, R.H.; Elger, G.W.

    1987-01-01

    The Bureau of Mines smelted and sulfation-leached an ilmenite from northern Minnesota. The objective was to assess the feasibility of preparing chlorination-grade titanium feedstock. The concentrate was smelted with woodchips, coke, and soda ash in 91-kg-and -metric ton (mt)-capacity electric arc furnaces to form Ti-rich slag and commercial-grade pig iron. The final product meets charge specifications for chlorination. However, more large-scale testing is necessary. This report is based upon work performed under a Memorandum of Agreement between NICOR Mineral Ventures and the Bureau of Mines.

  7. Manufacturing and Application of Metalized Ore-Coal Pellets in Synthetic Pig Iron Smelting

    Science.gov (United States)

    Nokhrina, O. I.; Rozhikhina, I. D.; Khodosov, I. E.

    2016-08-01

    The article presents research data on manufacturing and application of metalized ore-coal pellets in synthetic pig iron smelting. A technology of pellets metallization by means of solid-phase reduction of iron from oxides using hematite-magnetite iron ore and low-caking coal as raw materials is described. Industrial testing of replacing 10, 15, and 20% of waste metal by the metalized ore-coal pellets in the coreless induction furnace IST-1 is described. Optimal temperature and time conditions of feeding the metalized pellets into the furnace in smelting pig iron of SCh-40-60 grade are determined.

  8. Rapid sintering of anisotropic, nanograined Nd-Fe-B by flash-spark plasma sintering

    Science.gov (United States)

    Castle, Elinor; Sheridan, Richard; Grasso, Salvatore; Walton, Allan; Reece, Mike

    2016-11-01

    A Spark Plasma Sintering (SPS) furnace was used to Flash-Sinter (FS) Nd-Fe-Dy-Co-B-Ga melt spun permanent magnetic material. During the 10 s "Flash" process (heating rate 2660 K min-1), sample sintering (to theoretical density) and deformation (54% height reduction) occurred. This produced texturing and significant magnetic anisotropy, comparable to conventional die-upset magnets; yet with much greater coercivities (>1600 kA m-1) due to the nanoscale characteristics of the plate-like sintered grains. These preliminary results suggest that Flash-SPS could provide a new processing route for the mass production of highly anisotropic, nanocrystalline magnetic materials with high coercivity.

  9. Production of bio-oils from wood by flash pyrolysis; Herstellung von Bio-Oelen aus Holz in einer Flash-Pyrolyseanlage

    Energy Technology Data Exchange (ETDEWEB)

    Meier, D.; Ollesch, T. [Bundesforschungsanstalt fuer Forst- und Holzwirtschaft, Hamburg (Germany). Inst. fuer Holzchemie und Chemische Technologie des Holzes; Gerdes, C.; Kaminsky, W. [Hamburg Univ. (Germany). Inst. fuer Technische und Makromolekulare Chemie (ITMCh)

    1998-09-01

    Flash pyrolysis is a medium-temperature process (around 475 C) in which biomass is heated up rapidly in the absence of oxygen. The pyrolysis products are cooled down rapidly, condensing into a reddish-brown liquid with around half the calorific value of a conventional heating oil. In contrast to conventional charcoal production, flash pyrolysis is a modern process whose process parameters enure high liquid yields. Modern fluidized-bed reactors for flash pyrolysis of biomass tend to have high heating rates and short times of residue. In the `Hamburg process`, fluidized-bed reactors are used successfully for pyrolysis of plastics. A flash pyrolysis plant for biomass treatment was constructed in cooperation with Hamburg University with funds provided by the `Bundesstiftung Umwelt`. This contribution describes the first series of experiments, mass balances and oil analyses using beech wood as material to be pyrolyzed. (orig./SR) [Deutsch] Flash-Pyrolyse ist ein Mitteltemperatur-Prozess (ca. 475 C), in dem Biomasse unter Sauerstoffausschluss sehr schnell erhitzt wird. Die entstehenden Pyrolyseprodukte werden schnell abgekuehlt und kondensieren zu einer roetlich-braunen Fluessigkeit, die etwa die Haelfte des Heizwertes eines konventionellen Heizoeles besitzt. Flash-Pyrolyse ist, im Gegensatz zur konventionellen Holzverkohlung, ein modernes Verfahren, dessen spezielle Verfahrensparameter hohe Fluessigausbeuten ermoeglichen. Hohe Aufheizraten, verbunden mit kurzen Verweilzeiten, werden mit stationaeren Wirbelbettreaktoren erzielt die gegenwaertig vorwiegend fuer die Flash-Pyrolyse von Biomasse eingesetzt werden. Im `Hamburger Verfahren` haben sich Wirbelbettreaktoren im Bereich der Kunststoffpyrolyse bewaehrt. Daher wurde in Zusammenarbeit mit der Universitaet Hamburg und finanzieller Foerderung der Bundesstiftung Umwelt eine Flash-Pyrolyseanlage fuer Biomasse gebaut: In dieser Arbeit werden erste Versuchsreihen, Massenbilanzen und Oelanalysen aus der Pyrolyse von

  10. 铜冶炼含砷污水处理%Treatment of Arsenic -Bearing Wastewater from Copper Smelting

    Institute of Scientific and Technical Information of China (English)

    龙大祥

    2000-01-01

    简述铜冶炼企业工业污水中砷的来源,讨论含砷工业污水的处理工艺及处理指标,结合生产实际分析污水处理工艺运行中的影响因素及解决办法,总结在污水处理设计工作的经验。提出污水处理工艺的发展思路。%Sources of arsenic in the industrial wastewater from copper smelting enterprises are briefly de-scribed.Technologies and indexes for the treatment of arsenic - bearing wastewater are discussed.Factors affecting theoperation of wastewater treatment processes are analysed in the light of productive practices. Experiences in the designingof wastewater treatment are summarised.Train of thought on the development of wastewater treatment technologies is ad-vanced.

  11. Search Engine Optimization for Flash Best Practices for Using Flash on the Web

    CERN Document Server

    Perkins, Todd

    2009-01-01

    Search Engine Optimization for Flash dispels the myth that Flash-based websites won't show up in a web search by demonstrating exactly what you can do to make your site fully searchable -- no matter how much Flash it contains. You'll learn best practices for using HTML, CSS and JavaScript, as well as SWFObject, for building sites with Flash that will stand tall in search rankings.

  12. Adobe Flash Professional CS6 digital classroom

    CERN Document Server

    Team, AGI Creative

    2012-01-01

    Full-color book and video package teaches you Flash in a flash! If you want to design and maintain dynamic websites with Adobe Flash, this full-color book-and-video training package from expert instructors is the perfect place to start. Fifteen self-paced, step-by-step lessons are accompanied by video tutorials, and this powerful combination helps you master the basics, acquire essential skills, and learn what's new. Making all aspects of Flash less intimidating, this superb training tool covers topics such as using layers to build animation sequences, creating interactive web

  13. Flash CS5 The Missing Manual

    CERN Document Server

    Grover, Chris

    2010-01-01

    Once you know how to use Flash, you can create everything from simple animations to high-end desktop applications, but it's a complex tool that can be difficult to master on your own-unless you have this Missing Manual. This book will help you learn all you need to know about Flash CS5 to create animations that bring your ideas to life. Learn animation basics. Find everything you need to know to get started with FlashMaster the Flash tools. Learn the animation and effects toolset, with clear explanations and hands-on examplesUse 3D effects. Rotate and put objects in motion in three dimensions

  14. GeckoFTL: Scalable Flash Translation Techniques For Very Large Flash Devices

    DEFF Research Database (Denmark)

    Dayan, Niv; Bonnet, Philippe; Idreos, Stratos

    2016-01-01

    The volume of metadata needed by a flash translation layer (FTL) is proportional to the storage capacity of a flash device. Ideally, this metadata should reside in the device's integrated RAM to enable fast access. However, as flash devices scale to terabytes, the necessary volume of metadata...

  15. Mitochondrial Flash: Integrative Reactive Oxygen Species and pH Signals in Cell and Organelle Biology.

    Science.gov (United States)

    Wang, Wang; Gong, Guohua; Wang, Xianhua; Wei-LaPierre, Lan; Cheng, Heping; Dirksen, Robert; Sheu, Shey-Shing

    2016-09-20

    Recent breakthroughs in mitochondrial research have advanced, reshaped, and revolutionized our view of the role of mitochondria in health and disease. These discoveries include the development of novel tools to probe mitochondrial biology, the molecular identification of mitochondrial functional proteins, and the emergence of new concepts and mechanisms in mitochondrial function regulation. The discovery of "mitochondrial flash" activity has provided unique insights not only into real-time visualization of individual mitochondrial redox and pH dynamics in live cells but has also advanced understanding of the excitability, autonomy, and integration of mitochondrial function in vivo. The mitochondrial flash is a transient and stochastic event confined within an individual mitochondrion and is observed in a wide range of organisms from plants to Caenorhabditis elegans to mammals. As flash events involve multiple transient concurrent changes within the mitochondrion (e.g., superoxide, pH, and membrane potential), a number of different mitochondrial targeted fluorescent indicators can detect flash activity. Accumulating evidence indicates that flash events reflect integrated snapshots of an intermittent mitochondrial process arising from mitochondrial respiration chain activity associated with the transient opening of the mitochondrial permeability transition pore. We review the history of flash discovery, summarize current understanding of flash biology, highlight controversies regarding the relative roles of superoxide and pH signals during a flash event, and bring forth the integration of both signals in flash genesis. Investigations using flash as a biomarker and establishing its role in cell signaling pathway will move the field forward. Antioxid. Redox Signal. 25, 534-549.

  16. Flash floods, hydro-geomorphic response and risk management

    Science.gov (United States)

    Braud, Isabelle; Borga, Marco; Gourley, Jonathan; Hürlimann, Marcel; Zappa, Massimilano; Gallart, Francesc

    2016-10-01

    Each year, natural disasters are responsible for fatalities and economic losses worldwide with 101 billion USD in economic losses and 7000 fatalities reported for 2014 (SwissRE, 2015). Even if earthquakes are responsible for most of these fatalities, flash floods and landslides are recognized as a significant source of threat to human lives (SwissRE, 2015). Jonkman (2005), in a global assessment of flood-related casualties, showed that flash floods lead to the highest mortality (number of fatalities divided by the number of affected people). They are also often associated with shallow landslides and geomorphic processes that can increase threat to human lives. Analysis of a global data set of fatalities from non-seismically triggered landslides (Petley, 2012) shows that 2620 fatal landslides were recorded worldwide in the period 2004-2010, causing a total of 32,322 recorded fatalities. In addition, heavy precipitation events, at the origin of flash floods and shallow landsliding are expected to increase in the future (e.g. Scoccimarro et al., 2016 for a recent study in Europe). Progress in flash floods and landslides understanding, forecasting and warning is therefore still needed to disentangle the complex interactions between hazards, exposure and vulnerability and to increase resilience (Borga et al., 2014).

  17. Permeability transition pore-mediated mitochondrial superoxide flashes regulate cortical neural progenitor differentiation.

    Science.gov (United States)

    Hou, Yan; Mattson, Mark P; Cheng, Aiwu

    2013-01-01

    In the process of neurogenesis, neural progenitor cells (NPCs) cease dividing and differentiate into postmitotic neurons that grow dendrites and an axon, become excitable, and establish synapses with other neurons. Mitochondrial biogenesis and aerobic metabolism provide energy substrates required to support the differentiation, growth and synaptic activity of neurons. Mitochondria may also serve signaling functions and, in this regard, it was recently reported that mitochondria can generate rapid bursts of superoxide (superoxide flashes), the frequency of which changes in response to environmental conditions and signals including oxygen levels and Ca(2+) fluxes. Here we show that the frequency of mitochondrial superoxide flashes increases as embryonic cerebral cortical neurons differentiate from NPCs, and provide evidence that the superoxide flashes serve a signaling function that is critical for the differentiation process. The superoxide flashes are mediated by mitochondrial permeability transition pore (mPTP) opening, and pharmacological inhibition of the mPTP suppresses neuronal differentiation. Moreover, superoxide flashes and neuronal differentiation are inhibited by scavenging of mitochondrial superoxide. Conversely, manipulations that increase superoxide flash frequency accelerate neuronal differentiation. Our findings reveal a regulatory role for mitochondrial superoxide flashes, mediated by mPTP opening, in neuronal differentiation.

  18. 76 FR 14636 - National Emission Standards for Hazardous Air Pollutants: Primary Lead Smelting

    Science.gov (United States)

    2011-03-17

    ... Air Pollutants for Primary Lead Smelting (76 FR 9410). The EPA is extending the deadline for written...-2004-0305, by one of the following methods: http://www.regulations.gov : Follow the on-line... the use of special characters, any form of encryption, and be free of any defects or viruses....

  19. RISK ASSESSMENT AND REMEDIATION OF SOILS CONTAMINATED BY MINING AND SMELTING OF LEAD, ZINC AND CADMIUM

    Science.gov (United States)

    Mining nd smelting of Pb, Zn and Cd ores have caused widespread soil contamination in many countries. In locations with severe soil contamination, and strongly acidic soil or mine waste, ecosystems are devastated. Research has shown that An phytotoxicity, Pb-induced phosphate def...

  20. Shanghang 200,000 Tonnes Copper Smelting Project Speeds up The Pace of Construction

    Institute of Scientific and Technical Information of China (English)

    2012-01-01

    <正>The 200,000 tonnes copper smelting project of Zijin Copper Co.,Ltd with a total investment of 5 billion yuan is located in Shanghang Jiaoyang Circular Economy Industrial Park,since the start of construction in June last year,

  1. Looking for Similarities Between Lowland (Flash) Floods

    Science.gov (United States)

    Brauer, C.; Teuling, R.; Torfs, P.; Hobbelt, L.; Jansen, F.; Melsen, L.; Uijlenhoet, R.

    2012-12-01

    On 26 August 2010 the eastern part of The Netherlands and the bordering part of Germany were struck by a series of rainfall events. Over an area of 740 km2 more than 120 mm of rainfall were observed in 24 h. We investigated the unprecedented flash flood triggered by this exceptionally heavy rainfall event (return period > 1000 years) in the 6.5 km2 Hupsel Brook catchment, which has been the experimental watershed employed by Wageningen University since the 1960s. This study improved our understanding of the dynamics of such lowland flash floods (Brauer et al., 2011). These observations, however, only show how our experimental catchment behaved and the results cannot be extrapolated directly to different floods in other (neighboring) lowland catchments. Therefore, it is necessary to use the information collected in one well-monitored catchment in combination with data from other, less well monitored catchments to find common signatures which could describe the runoff response during a lowland flood as a function of catchment characteristics. Because of the large spatial extent of the rainfall event in August 2010, many brooks and rivers in the Netherlands and Germany flooded. With data from several catchments we investigated the influence of rainfall and catchment characteristics (such as slope, size and land use) on the reaction of discharge to rainfall. We also investigated the runoff response in these catchments during previous floods by analyzing the relation between storage and discharge and the recession curve. In addition to the flood in August 2010, two other floods occurred in The Netherlands in recently. The three floods occurred in different parts of the country, after different types of rainfall events and with different initial conditions. We selected several catchments during each flood to compare their response and find out if these cases are fundamentally different or that they were produced by the same underlying processes and can be treated in a

  2. Oxidative damage of workers in secondary metal recovery plants affected by smoking status and joining the smelting work.

    Science.gov (United States)

    Chia, Taipau; Hsu, Ching Yi; Chen, Hsiu Ling

    2008-04-01

    In Taiwan, secondary copper smelters and zinc recovery plants primarily utilize recovering metal from scrap and dross, and handles mostly fly ash and slag with high temperature to produce ZnO from the iron and steel industry. The materials may contain organic impurities, such as plastic and organic chloride chemicals, and amounts of polychlorinated dibenzo-p-dioxins and polychlorinated dibenzofurans (PCDD/Fs) are produced during the smelting process. Therefore, secondary metal recovery industries are major emission sources of PCDD/Fs, which may have been demonstrated to elicit oxidative stress and to involve the production of plasma malondialdehyde (MDA). Many studies have also indicated that the intake of antioxidants, smoking, age and exposure to environmental pollutants may be implicated to DNA damage or lipid peroxidation. This study therefore aims to elucidate the roles of occupational exposure like joining the smelting work, age, smoking and alcohol status, and antioxidant intake on oxidative damage in secondary metal recovery workers in Taiwan. 73 workers were recruited from 2 secondary metal recovery plants. The analysis of 8-hydroxydeoxyguanosine (8-OH-dG) in urine, DNA strand breakage (comet assay) and lipid peroxidation (MDA) in blood samples were completed for all of the workers. The results showed that the older subjects exhibited significantly lower levels of 8-OH-dG and MDA than younger subjects. Our investigation also showed that working departments were in related to plasma MDA and DNA strand breakage levels of nonsmokers, however, the observation become negligible in smokers. And it is implicated that cigarette type might affect 8-OH-dG levels in secondary metal recovery workers. Since, adding to results above, the MDA level in production workers was significantly higher than those in managerial departments, it is important for the employers to make efforts on improving occupational environments or serving protective equipments to protect workers

  3. A NEW APPROACH TO DESIGN LOW POWER CMOS FLASH A/D CONVERTER

    Directory of Open Access Journals (Sweden)

    Sudakar S. Chauhan

    2011-07-01

    Full Text Available In the present paper, a 4-bit flash analog to digital converter for low power SoC application is presented.CMOS inverter has been used as a comparator and by adjusting the ratio of channel width and length, theswitching threshold of the CMOS inverter is varied to detect the input analog signal. The simulation resultsshow that this proposed 4-bit flash ADC consumes about 12.4 mW at 200M sample/s with 3.3V supplyvoltage in TSMC 0.35 μm process. Compared with the traditional flash ADC, this proposed method canreduce about 78% in power consumption.

  4. SEMICONDUCTOR INTEGRATED CIRCUITS A low-voltage sense amplifier for high-performance embedded flash memory

    Science.gov (United States)

    Jiang, Liu; Xueqiang, Wang; Qin, Wang; Dong, Wu; Zhigang, Zhang; Liyang, Pan; Ming, Liu

    2010-10-01

    This paper presents a sense amplifier scheme for low-voltage embedded flash (eFlash) memory applications. The topology of the sense amplifier is based on current mode comparison. Moreover, an offset-voltage elimination technique is employed to improve the sensing performance under a small memory cell current. The proposed sense amplifier is designed based on a GSMC 130 nm eFlash process, and the sense time is 0.43 ns at 1.5 V, corresponding to a 46% improvement over the conventional technologies.

  5. Flash Expansion Threshold in Whirligig Swarms.

    Directory of Open Access Journals (Sweden)

    William L Romey

    Full Text Available In the selfish herd hypothesis, prey animals move toward each other to avoid the likelihood of being selected by a predator. However, many grouped animals move away from each other the moment before a predator attacks. Very little is known about this phenomenon, called flash expansion, such as whether it is triggered by one individual or a threshold and how information is transferred between group members. We performed a controlled experiment with whirligig beetles in which the ratio of sighted to unsighted individuals was systematically varied and emergent flash expansion was measured. Specifically, we examined: the percentage of individuals in a group that startled, the resulting group area, and the longevity of the flash expansion. We found that one or two sighted beetles in a group of 24 was not enough to cause a flash expansion after a predator stimulus, but four sighted beetles usually initiated a flash expansion. Also, the more beetles that were sighted the larger the resulting group area and the longer duration of the flash expansion. We conclude that flash expansion is best described as a threshold event whose adaptive value is to prevent energetically costly false alarms while quickly mobilizing an emergent predator avoidance response. This is one of the first controlled experiments of flash expansion, an important emergent property that has applications to understanding collective motion in swarms, schools, flocks, and human crowds. Also, our study is a convincing demonstration of social contagion, how the actions of one individual can pass through a group.

  6. On Coding Efficiency for Flash Memories

    CERN Document Server

    Ma, Xudong

    2012-01-01

    Recently, flash memories have become a competitive solution for mass storage. The flash memories have rather different properties compared with the rotary hard drives. That is, the writing of flash memories is constrained, and flash memories can endure only limited numbers of erases. Therefore, the design goals for the flash memory systems are quite different from these for other memory systems. In this paper, we consider the problem of coding efficiency. We define the "coding-efficiency" as the amount of information that one flash memory cell can be used to record per cost. Because each flash memory cell can endure a roughly fixed number of erases, the cost of data recording can be well-defined. We define "payload" as the amount of information that one flash memory cell can represent at a particular moment. By using information-theoretic arguments, we prove a coding theorem for achievable coding rates. We prove an upper and lower bound for coding efficiency. We show in this paper that there exists a fundamen...

  7. Heat wave flash droughts in decline

    Science.gov (United States)

    Mo, Kingtse C.; Lettenmaier, Dennis P.

    2015-04-01

    Flash drought is a term that was popularized during rapidly evolving droughts in the Central U.S. in 2012 that were associated with heat waves. We posit that there are two kinds of flash droughts, and we will focus on heat wave flash droughts, of which the 2012 events were typical. We find, based on an analysis of temperature observations and model-reconstructed soil moisture (SM) and evapotranspiration from 1916 to 2013, that heat wave flash droughts in the conterminous U.S. (CONUS) are most likely to occur over the Midwest and the Pacific Northwest during the growing season. We also find that the number of such events across the CONUS has been decreasing over the last century but rebounded after 2011. The long-term downward trends appear to be associated with generally increasing trends in SM resulting from increasing trends in precipitation over the areas where heat wave flash droughts are most likely to occur.

  8. Smelt was the likely beneficiary of an antifreeze gene laterally transferred between fishes

    Directory of Open Access Journals (Sweden)

    Graham Laurie A

    2012-09-01

    Full Text Available Abstract Background Type II antifreeze protein (AFP from the rainbow smelt, Osmerus mordax, is a calcium-dependent C-type lectin homolog, similar to the AFPs from herring and sea raven. While C-type lectins are ubiquitous, type II AFPs are only found in a few species in three widely separated branches of teleost fishes. Furthermore, several other non-homologous AFPs are found in intervening species. We have previously postulated that this sporadic distribution has resulted from lateral gene transfer. The alternative hypothesis, that the AFP evolved from a lectin present in a shared ancestor and that this gene was lost in most species, is not favored because both the exon and intron sequences are highly conserved. Results Here we have sequenced and annotated a 160 kb smelt BAC clone containing a centrally-located AFP gene along with 14 other genes. Quantitative PCR indicates that there is but a single copy of this gene within the smelt genome, which is atypical for fish AFP genes. The corresponding syntenic region has been identified and searched in a number of other species and found to be devoid of lectin or AFP sequences. Unlike the introns of the AFP gene, the intronic sequences of the flanking genes are not conserved between species. As well, the rate and pattern of mutation in the AFP gene are radically different from those seen in other smelt and herring genes. Conclusions These results provide stand-alone support for an example of lateral gene transfer between vertebrate species. They should further inform the debate about genetically modified organisms by showing that gene transfer between ‘higher’ eukaryotes can occur naturally. Analysis of the syntenic regions from several fishes strongly suggests that the smelt acquired the AFP gene from the herring.

  9. Interactions between hatch dates, growth rates, and mortality of Age-0 native Rainbow Smelt and nonnative Alewife in Lake Champlain

    Science.gov (United States)

    Parrish, Donna; Simonin, Paul W.; Rudstam, Lars G.; Pientka, Bernard; Sullivan, Patrick J.

    2016-01-01

    Timing of hatch in fish populations can be critical for first-year survival and, therefore, year-class strength and subsequent species interactions. We compared hatch timing, growth rates, and subsequent mortality of age-0 Rainbow Smelt Osmerus mordax and Alewife Alosa pseudoharengus, two common open-water fish species of northern North America. In our study site, Lake Champlain, Rainbow Smelt hatched (beginning May 26) almost a month earlier than Alewives (June 20). Abundance in the sampling area was highest in July for age-0 Rainbow Smelt and August for age-0 Alewives. Late-hatching individuals of both species grew faster than those hatching earlier (0.6 mm/d versus 0.4 for Rainbow Smelt; 0.7 mm/d versus 0.6 for Alewives). Mean mortality rate during the first 45 d of life was 3.4%/d for age-0 Rainbow Smelt and was 5.5%/d for age-0 Alewives. Alewife mortality rates did not differ with hatch timing but daily mortality rates of Rainbow Smelt were highest for early-hatching fish. Cannibalism is probably the primary mortality source for age-0 Rainbow Smelt in this lake. Therefore, hatching earlier may not be advantageous because the overlap of adult and age-0 Rainbow Smelt is highest earlier in the season. However, Alewives, first documented in Lake Champlain in 2003, may increase the mortality of age-0 Rainbow Smelt in the summer, which should favor selection for earlier hatching.

  10. Post-depositional redistribution of trace metals in reservoir sediments of a mining/smelting-impacted watershed (the Lot River, SW France)

    Energy Technology Data Exchange (ETDEWEB)

    Audry, Stephane, E-mail: audry@lmtg.obs-mip.fr [Universite de Bordeaux, UMR 5805 EPOC, Avenue des facultes, 33405 Talence cedex (France)] [Universite de Limoges, Groupement de Recherche Eau Sol Environnement, IFR 145 GEIST, FST, 123 Avenue, A. Thomas, 87060 Limoges cedex (France)] [Universite de Toulouse, UPS (OMP), LMTG, 14 Av., Edouard Belin, F-31400 Toulouse (France); Grosbois, Cecile [Universite de Limoges, Groupement de Recherche Eau Sol Environnement, IFR 145 GEIST, FST, 123 Avenue, A. Thomas, 87060 Limoges cedex (France)] [Universite Francois-Rabelais de Tours, CNRS/INSU, Universite d' Orleans, UMR 6113 ISTO, FST, Parc Grandmont, F-37200 Tours (France); Bril, Hubert [Universite de Limoges, Groupement de Recherche Eau Sol Environnement, IFR 145 GEIST, FST, 123 Avenue, A. Thomas, 87060 Limoges cedex (France); Schaefer, Joerg [Universite de Bordeaux, UMR 5805 EPOC, Avenue des facultes, 33405 Talence cedex (France); Kierczak, Jakub [Universite de Limoges, Groupement de Recherche Eau Sol Environnement, IFR 145 GEIST, FST, 123 Avenue, A. Thomas, 87060 Limoges cedex (France)] [University of Wroclaw, Institute of Geological Sciences, Cybulskiego 30, 50-205 Wroclaw (Poland); Blanc, Gerard [Universite de Bordeaux, UMR 5805 EPOC, Avenue des facultes, 33405 Talence cedex (France)

    2010-06-15

    Mining/smelting wastes and reservoir sediment cores from the Lot River watershed were studied using mineralogical (XRD, SEM-EDS, EMPA) and geochemical (redox dynamics, selective extractions) approaches to characterize the main carrier phases of trace metals. These two approaches permitted determining the role of post-depositional redistribution processes in sediments and their effects on the fate and mobility of trace metals. The mining/smelting wastes showed heterogeneous mineral compositions with highly variable contents of trace metals. The main trace metal-bearing phases include spinels affected by secondary processes, silicates and sulfates. The results indicate a clear change in the chemical partitioning of trace metals between the reservoir sediments upstream and downstream of the mining/smelting activities, with the downstream sediments showing a 2-fold to 5-fold greater contribution of the oxidizable fraction. This increase was ascribed to stronger post-depositional redistribution of trace metals related to intense early diagenetic processes, including dissolution of trace metal-bearing phases and precipitation of authigenic sulfide phases through organic matter (OM) mineralization. This redistribution is due to high inputs (derived from mining/smelting waste weathering) at the water-sediment interface of (i) dissolved SO{sub 4} promoting more efficient OM mineralization, and (ii) highly reactive trace metal-bearing particles. As a result, the main trace metal-bearing phases in the downstream sediments are represented by Zn- and Fe-sulfides, with minor occurrence of detrital zincian spinels, sulfates and Fe-oxyhydroxides. Sequestration of trace metals in sulfides at depth in reservoir sediments does not represent long term sequestration owing to possible resuspension of anoxic sediments by natural (floods) and/or anthropogenic (dredging, dam flush) events that might promote trace metal mobilization through sulfide oxidation. It is estimated that, during a

  11. Terrestrial gamma-ray flashes

    Energy Technology Data Exchange (ETDEWEB)

    Marisaldi, Martino, E-mail: marisaldi@iasfbo.inaf.it [INAF-IASF Bologna, Via Gobetti 101, I-40129 Bologna (Italy); Fuschino, Fabio; Labanti, Claudio [INAF-IASF Bologna, Via Gobetti 101, I-40129 Bologna (Italy); Tavani, Marco [INAF-IASF Roma, Via Fosso del Cavaliere 100, I-00133 Roma (Italy); Argan, Andrea [INAF, Viale del Parco Mellini 84, 00136 Roma (Italy); Del Monte, Ettore [INAF-IASF Roma, Via Fosso del Cavaliere 100, I-00133 Roma (Italy); Longo, Francesco; Barbiellini, Guido [Dipartimento di Fisica Università di Trieste and INFN Trieste, via A. Valerio 2, I-34127 Trieste (Italy); Giuliani, Andrea [INAF-IASF Milano, Via Bassini 15, I-20133 Milano (Italy); Trois, Alessio [INAF Osservatorio Astronomico di Cagliari, loc. Poggio dei Pini, strada 54, I-09012 Capoterra (Italy); Bulgarelli, Andrea; Gianotti, Fulvio; Trifoglio, Massimo [INAF-IASF Bologna, Via Gobetti 101, I-40129 Bologna (Italy)

    2013-08-21

    Lightning and thunderstorm systems in general have been recently recognized as powerful particle accelerators, capable of producing electrons, positrons, gamma-rays and neutrons with energies as high as several tens of MeV. In fact, these natural systems turn out to be the highest energy and most efficient natural particle accelerators on Earth. Terrestrial Gamma-ray Flashes (TGFs) are millisecond long, very intense bursts of gamma-rays and are one of the most intriguing manifestation of these natural accelerators. Only three currently operative missions are capable of detecting TGFs from space: the RHESSI, Fermi and AGILE satellites. In this paper we review the characteristics of TGFs, including energy spectrum, timing structure, beam geometry and correlation with lightning, and the basic principles of the associated production models. Then we focus on the recent AGILE discoveries concerning the high energy extension of the TGF spectrum up to 100 MeV, which is difficult to reconcile with current theoretical models.

  12. [Nikola Tesla: flashes of inspiration].

    Science.gov (United States)

    Villarejo-Galende, Albero; Herrero-San Martín, Alejandro

    2013-01-16

    Nikola Tesla (1856-1943) was one of the greatest inventors in history and a key player in the revolution that led to the large-scale use of electricity. He also made important contributions to such diverse fields as x-rays, remote control, radio, the theory of consciousness or electromagnetism. In his honour, the international unit of magnetic induction was named after him. Yet, his fame is scarce in comparison with that of other inventors of the time, such as Edison, with whom he had several heated arguments. He was a rather odd, reserved person who lived for his inventions, the ideas for which came to him in moments of inspiration. In his autobiography he relates these flashes with a number of neuropsychiatric manifestations, which can be seen to include migraine auras, synaesthesiae, obsessions and compulsions.

  13. Impact Flash Physics: Modeling and Comparisons With Experimental Results

    Science.gov (United States)

    Rainey, E.; Stickle, A. M.; Ernst, C. M.; Schultz, P. H.; Mehta, N. L.; Brown, R. C.; Swaminathan, P. K.; Michaelis, C. H.; Erlandson, R. E.

    2015-12-01

    Hypervelocity impacts frequently generate an observable "flash" of light with two components: a short-duration spike due to emissions from vaporized material, and a long-duration peak due to thermal emissions from expanding hot debris. The intensity and duration of these peaks depend on the impact velocity, angle, and the target and projectile mass and composition. Thus remote sensing measurements of planetary impact flashes have the potential to constrain the properties of impacting meteors and improve our understanding of impact flux and cratering processes. Interpreting impact flash measurements requires a thorough understanding of how flash characteristics correlate with impact conditions. Because planetary-scale impacts cannot be replicated in the laboratory, numerical simulations are needed to provide this insight for the solar system. Computational hydrocodes can produce detailed simulations of the impact process, but they lack the radiation physics required to model the optical flash. The Johns Hopkins University Applied Physics Laboratory (APL) developed a model to calculate the optical signature from the hot debris cloud produced by an impact. While the phenomenology of the optical signature is understood, the details required to accurately model it are complicated by uncertainties in material and optical properties and the simplifications required to numerically model radiation from large-scale impacts. Comparisons with laboratory impact experiments allow us to validate our approach and to draw insight regarding processes that occur at all scales in impact events, such as melt generation. We used Sandia National Lab's CTH shock physics hydrocode along with the optical signature model developed at APL to compare with a series of laboratory experiments conducted at the NASA Ames Vertical Gun Range. The experiments used Pyrex projectiles to impact pumice powder targets with velocities ranging from 1 to 6 km/s at angles of 30 and 90 degrees with respect to

  14. Radiometry of flashing LED sources

    Science.gov (United States)

    Gregory, Don A.; Medley, Stephanie; Roberts, Adam

    2008-08-01

    A laboratory based technique has been devised for measuring the illumination characteristics of flashing light emitting diode (LED) sources. The difference between the photopic measurement of a continuous source and a flashing source is that some analytic method must be incorporated into the measurement to account for the response of the eye. Ohno et al have devised an analytic expression for the impulse response of the eye, which closely matches existing forms used for finding effective intensity1. These other forms are the Blondel-Rey equation, the Form Factor method, and the Allard method.4,5,6 Ohno's research suggests a modified Allard method, but offers no procedure for actually making the measurement. In this research, the modified Allard1 method approach has been updated using standard laboratory equipment such as a silicon detector in conjunction with a digital multi-meter and Labview® software to make this measurement. Labview® allows exact computation of the modified Allard method. However, an approximation scheme for the conversion from radiometric units to photopic units must be adopted. The LED spectral form is approximately a Gaussian line shape with full width at half maximum of about 15 to 30nm. The Gaussian curve makes converting from radiometric to photopic units difficult. To simplify, the technique presented here estimates the spectral form of the LEDs to be a Dirac delta function situated at the peak wavelength. This allows the conversion from watts to lumens to be a simple application of the luminous efficiency curve.2 For LEDs with a full width half maximum of 20nm, this scheme is found to be accurate to +/- 5%.

  15. 有色金属复杂资源低温碱性熔炼原理与方法%Principle and method of low temperature alkaline smelting in non-ferrous metallurgy complicated resources

    Institute of Scientific and Technical Information of China (English)

    郭学益; 刘静欣; 田庆华; 李栋

    2013-01-01

      低温碱性熔炼是一种有色冶金高效清洁生产方法,可处理复杂难处理原生资源和二次资源等。根据熔炼体系的不同,将低温碱性熔炼分为直接熔炼、氧化熔炼、还原熔炼三类,并阐述了该方法的相关理论、发展概况和研究进展,具体介绍了其在铝灰、废弃电路板等二次资源回收,铋精矿、锑精矿、铅精矿、再生铅物料、多金属复杂矿冶炼,以及二氧化硅、氧化锌材料制备等方面的应用。研究表明该方法具有金属直收率高、环保、节能等优点,具有广阔的应用前景。%Low temperature alkaline smelting is an effective cleaner product method in non-ferrous metallurgy, especially in the separation and extraction of complex resources and secondary resources. Low temperature alkaline smelting is divided into direct smelting, oxidizing smelting and reducing smelting according to the different system. The basic fundamental, development status and applications of this process are introduced and summarized. The recovery of valuable metals from waste printed circuit board, aluminum dross, the smelting process of bismuth concentrate, antimony concentrate, lead concentrate, regenerated lead, and complicated metal resources, and the preparation of silicon dioxide and zinc oxide are expounded in detail. The study shows that this method has broad application prospects with great advantages, such as high straight yield, environmental protection, energy saving, etc.

  16. Mitochondrial Flash: Integrative Reactive Oxygen Species and pH Signals in Cell and Organelle Biology

    Science.gov (United States)

    Gong, Guohua; Wang, Xianhua; Wei-LaPierre, Lan; Cheng, Heping; Dirksen, Robert

    2016-01-01

    Abstract Significance: Recent breakthroughs in mitochondrial research have advanced, reshaped, and revolutionized our view of the role of mitochondria in health and disease. These discoveries include the development of novel tools to probe mitochondrial biology, the molecular identification of mitochondrial functional proteins, and the emergence of new concepts and mechanisms in mitochondrial function regulation. The discovery of “mitochondrial flash” activity has provided unique insights not only into real-time visualization of individual mitochondrial redox and pH dynamics in live cells but has also advanced understanding of the excitability, autonomy, and integration of mitochondrial function in vivo. Recent Advances: The mitochondrial flash is a transient and stochastic event confined within an individual mitochondrion and is observed in a wide range of organisms from plants to Caenorhabditis elegans to mammals. As flash events involve multiple transient concurrent changes within the mitochondrion (e.g., superoxide, pH, and membrane potential), a number of different mitochondrial targeted fluorescent indicators can detect flash activity. Accumulating evidence indicates that flash events reflect integrated snapshots of an intermittent mitochondrial process arising from mitochondrial respiration chain activity associated with the transient opening of the mitochondrial permeability transition pore. Critical Issues: We review the history of flash discovery, summarize current understanding of flash biology, highlight controversies regarding the relative roles of superoxide and pH signals during a flash event, and bring forth the integration of both signals in flash genesis. Future Directions: Investigations using flash as a biomarker and establishing its role in cell signaling pathway will move the field forward. Antioxid. Redox Signal. 25, 534–549. PMID:27245241

  17. Spatial Frequency Modulates the Degree of Illusory Second Flash Perception.

    Science.gov (United States)

    Takeshima, Yasuhiro; Gyoba, Jiro

    2015-01-01

    When a brief single flash is presented simultaneously with two brief beeps, the number of presented flashes is often perceived as two. This phenomenon is referred to as the fission illusion. Several effects related to the fission illusion have been investigated using both psychophysical and neurophysiological methods. The present study examined the effects of spatial frequency on the fission illusion. At a low spatial frequency, transient channels respond preferably; conversely, sustained channels respond preferably at a high spatial frequency. Sustained channels differ in temporal properties from transient channels and are characterized by poor temporal resolution and slow-onset responses. In our previous study, visual stimuli presented at a slow processing speed were not conducive to the fission illusion. Therefore, we hypothesized that the fission illusion would not be difficult to observe when using high spatial frequencies. The results indicated that the degree of the perceived illusory second flash was reduced when spatial frequency was high as compared to when it was is low. Furthermore, according to signal detection theory, this difference between high and low spatial frequencies was not attributed to participants' response biases. Therefore, the fission illusion likely will not occur in conditions of slow processing speed and long response latencies in sustained channels, which respond preferably to high spatial frequency stimuli. Overall, the results indicated that the fission illusion was affected by temporal characteristics of lower-order sensory processing stages.

  18. Flash memory in embedded Java programs

    DEFF Research Database (Denmark)

    Korsholm, Stephan Erbs

    2011-01-01

    This paper introduces a Java execution environment with the capability for storing constant heap data in Flash, thus saving valuable RAM. The extension is motivated by the structure of three industrial applications which demonstrate the need for storing constant data in Flash on small embedded...... devices. The paper introduces the concept of host initialization of constant data to prepare a Flash image of constant data that can be kept outside the heap during runtime. The concept is implemented in an interpreter based Java execution environment....

  19. Jiangxi Copper Lead Zinc Smelting Project with an Investment of Nearly 5 billion yuan Started Construction in Hukou

    Institute of Scientific and Technical Information of China (English)

    2010-01-01

    <正>Recently,Jiangxi Copper Group Lead Zinc Smelting Project,a key construction project of Jiangxi Province’s "Ten,Hundred,Thousand Project" (referring to the plan to have a number of leading enterprises with annual sales topping

  20. Measuring hot flashes: summary of a National Institutes of Health workshop.

    Science.gov (United States)

    Miller, Heather G; Li, Rose Maria

    2004-06-01

    The etiology and mechanism of hot flashes remain incompletely understood. Future studies of hormonal and neurologic systems may provide promising leads to improve our understanding of the basic phenomenon and perhaps also shed light on the placebo effect. However, this is likely a complex undertaking. Critical to this effort is the ability to reliably identify when a hot flash has occurred. The leading objective measure in use today--sternal skin conductance monitoring--has some limitations in ambulatory settings. However, a more severe limitation is the inability of sternal skin conductance to provide any information on duration, intensity, and interference with activities. Ultimately, researchers desire a convenient and cost-effective sensor for monitoring hot flashes without cumbersome electrodes that might become compromised if a subject experiences extensive sweating or takes a shower and one that can capture data continuously for relatively long periods of observation. However, researchers also need well-characterized methods for collecting self-reported data. If the primary concern is helping women with hot flashes find relief, then subjective measures collected through diaries or interviews cannot be dismissed. Given the importance of this information, it would make sense to undertake methodologic research to ensure that the best possible systems are used to collect valid and reliable information. The factors that we want to measure with respect to hot flashes are likely to change over time as more is learned about the underlying phenomenon. This will probably be an evolutionary process, one involving decisions about what biological factors will be most useful for the task at hand, what technologies might be available or easily adaptable, which measures should be bundled together to maximize the precision of data collected with the available technology, and the analysis of the data to generate new hypotheses and perhaps the need for new measurement tools

  1. Age, growth and sex composition of the American smelt Osmerus mordax(Mitchill), of western Lake Superior

    Science.gov (United States)

    Bailey, Merryll M.

    1964-01-01

    This study is based on 4,561 smelt collected in Chequamegon Bay, the Apostle Islands, the Brule River, and Superior Harbor, all in western Lake Superior. Commercial production in the Great Lakes (U.S. and Canada combined) reached a peak of nearly 16 million pounds in 1960. Production in Lake Superior has generally been small but increased during the 1950's to reach 948,000 pounds in 1960. All O-group and spring I-group smelt had scales with sufficient sculpturing to permit detection of the first annulus. Annulus formation began after 6 June in 1960. In 1961, all smelt had completed the annulus by 24 August. The body-scale relation is a straight line with an intercept of -0.9 inch on the axis of fish length. The weight of western Lake Superior smelt increased as the 2.952 power of the length. A large range of length in each age group and resulting overlap of age-groups II-VI made length a poor index of age. Female smelt grew faster than males after the second year and dominated strongly in age-groups IV-VII. Both sexes made their best annual growth in length (3.3 inches) during their second year of life; the largest weight increments (0.74 ounce, males; 0.85 ounce, females) came in the third year. Best production from a commercial pound net in 1961 occurred when the sex ratios of spawning smelt were nearest 50:50. Spawning male smelt were consistently shorter than females and the average lengths of both sexes decreased as the spawning season progressed. Shortest mature smelt of each sex were 5.0 to 5.2 inches but the males are probably the first to reach 100 percent maturity. All year-old smelt were immature. Among 2-year-old fish, 40.7 per cent of the males and 17.7 percent of the females had reached maturity. All smelt more than 2 years old were mature. Ovaries of 10 smelt contained an average of 31,338 eggs for fish 7.3 to 8.8 inches long.

  2. Gone in a Flash: Manipulation of Audiovisual Temporal Integration Using Transcranial Magnetic Stimulation

    Directory of Open Access Journals (Sweden)

    Roy eHamilton

    2013-09-01

    Full Text Available While converging evidence implicates the right inferior parietal lobule in audiovisual integration, its role has not been fully elucidated by direct manipulation of cortical activity. Replicating and extending an experiment initially reported by Kamke, Vieth, Cottrell, and Mattingley (2012, we employed the sound-induced flash illusion, in which a single visual flash, when accompanied by two auditory tones, is misperceived as multiple flashes (Wilson, 1987; Shams, et al., 2000. Slow repetitive (1Hz TMS administered to the right angular gyrus, but not the right supramarginal gyrus, induced a transient decrease in the Peak Perceived Flashes (PPF, reflecting reduced susceptibility to the illusion. This finding independently confirms that perturbation of networks involved in multisensory integration can result in a more veridical representation of asynchronous auditory and visual events and that cross-modal integration is an active process in which the objective is the identification of a meaningful constellation of inputs, at times at the expense of accuracy.

  3. Gone in a flash: manipulation of audiovisual temporal integration using transcranial magnetic stimulation

    Science.gov (United States)

    Hamilton, Roy H.; Wiener, Martin; Drebing, Daniel E.; Coslett, H. Branch

    2013-01-01

    While converging evidence implicates the right inferior parietal lobule in audiovisual integration, its role has not been fully elucidated by direct manipulation of cortical activity. Replicating and extending an experiment initially reported by Kamke et al. (2012), we employed the sound-induced flash illusion, in which a single visual flash, when accompanied by two auditory tones, is misperceived as multiple flashes (Wilson, 1987; Shams et al., 2000). Slow repetitive (1 Hz) TMS administered to the right angular gyrus, but not the right supramarginal gyrus, induced a transient decrease in the Peak Perceived Flashes (PPF), reflecting reduced susceptibility to the illusion. This finding independently confirms that perturbation of networks involved in multisensory integration can result in a more veridical representation of asynchronous auditory and visual events and that cross-modal integration is an active process in which the objective is the identification of a meaningful constellation of inputs, at times at the expense of accuracy. PMID:24062701

  4. Gone in a flash: manipulation of audiovisual temporal integration using transcranial magnetic stimulation.

    Science.gov (United States)

    Hamilton, Roy H; Wiener, Martin; Drebing, Daniel E; Coslett, H Branch

    2013-01-01

    While converging evidence implicates the right inferior parietal lobule in audiovisual integration, its role has not been fully elucidated by direct manipulation of cortical activity. Replicating and extending an experiment initially reported by Kamke et al. (2012), we employed the sound-induced flash illusion, in which a single visual flash, when accompanied by two auditory tones, is misperceived as multiple flashes (Wilson, 1987; Shams et al., 2000). Slow repetitive (1 Hz) TMS administered to the right angular gyrus, but not the right supramarginal gyrus, induced a transient decrease in the Peak Perceived Flashes (PPF), reflecting reduced susceptibility to the illusion. This finding independently confirms that perturbation of networks involved in multisensory integration can result in a more veridical representation of asynchronous auditory and visual events and that cross-modal integration is an active process in which the objective is the identification of a meaningful constellation of inputs, at times at the expense of accuracy.

  5. Thermal acclimation to cold alters myosin content and contractile properties of rainbow smelt, Osmerus mordax, red muscle.

    Science.gov (United States)

    Coughlin, David J; Shiels, Lisa P; Nuthakki, Seshuvardhan; Shuman, Jacie L

    2016-06-01

    Rainbow smelt (Osmerus mordax), a eurythermal fish, live in environments from -1.8 to 20°C, with some populations facing substantial annual variation in environmental temperature. These different temperature regimes pose distinct challenges to locomotion by smelt. Steady swimming performance, red muscle function and muscle myosin content were examined to assess the prediction that cold acclimation by smelt will lead to improved steady swimming performance and that any performance shift will be associated with changes in red muscle function and in its myosin heavy chain composition. Cold acclimated (4°C) smelt had a faster maximum steady swimming speed and swam with a higher tailbeat frequency than warm acclimated (10°C) smelt when tested at the same temperature (10°C). Muscle mechanics experiments demonstrated faster contractile properties in the cold acclimated fish when tested at 10°C. The red muscle of cold acclimated smelt had a shorter twitch times, a shorter relaxation times and a higher maximum shortening velocity. In addition, red muscle from cold acclimated fish displayed reduced thermal sensitivity to cold, maintaining higher force levels at 4°C compared to red muscle from warm acclimated fish. Immunohistochemistry suggests shifts in muscle myosin composition and a decrease in muscle cross-sectional area with cold acclimation. Dot blot analysis confirmed a shift in myosin content. Rainbow smelt do show a significant thermal acclimation response to cold. An examination of published values of maximum muscle shortening velocity in fishes suggests that smelt are particularly well suited to high levels of activity in very cold water. Copyright © 2016 Elsevier Inc. All rights reserved.

  6. Toxic metal levels in children residing in a smelting craft village in Vietnam: a pilot biomonitoring study

    OpenAIRE

    Sanders, Alison P.; Miller, Sloane K.; Nguyen, Viet; Kotch, Jonathan B; Fry, Rebecca C.

    2014-01-01

    Background In Vietnam, environmental pollution caused by small-scale domestic smelting of automobile batteries into lead ingot is a growing concern. The village of Nghia Lo is a smelting craft village located roughly 25 km southeast of Hanoi in the Red River Delta. Despite the concern of toxic metal exposure in the village, biomonitoring among susceptible populations, such as children, has not been previously conducted. The aim of this study was to determine the body burden of toxic metals in...

  7. AOD炉的高效化冶炼模型%Efficient Smelting Model of AOD Furnace Steelmaking

    Institute of Scientific and Technical Information of China (English)

    艾立翔; 汪红兵; 徐安军; 田乃媛; 贺东风

    2012-01-01

    The research on traditional AOD efficient smelting was focused on enhancement of oxygen supply,optimization of improving volume ratio,increasing end hitting rate.Current device should be made full of,and AOD charging structure and oxygen supply should be optimized.Process parameters of AOD should be optimized.Physical heat and chemical heat should be rational used,and efficient smelting of AOD should be realized.Based on mass balance model and energy balance model,the model of AOD efficient smelting was proposed considering process features of AOD steelmaking.The change of tap to tap time with hot metal ratio and scrap steel ratio was simulated.The charging structure was got when tap to tap time was the shortest.The results indicate that the tap to tap time increases with molten iron ratio increasing in AOD steelmaking process with EAF stainless molten iron and BF molten iron.The tap to tap time increases with scrap steel ratio increasing in AOD steelmaking process with EAF stainless molten iron and scrap steel.The tap to tap time increases with scrap steel ratio increasing in AOD steelmaking process with BF molten iron and scrap steel.The tap to tap time with ferrosilicon heating agent is shorter than the time with carbon powder heating agent.%以往的AOD炉高效化冶炼研究往往通过提高供氧强度,优化转炉的炉容比,提高终点命中率等技术缩短冶炼周期,需要充分利用现有的设备,优化炉料结构和供氧制度,对生产工艺参数进行优化,充分利用这些物理热和化学热,实现AOD炉的高效化冶炼。开发了AOD炉高效化冶炼模型,在AOD炉物料平衡和能量平衡的基础上,结合AOD炉冶炼的工艺特征,建立AOD炉耗氧量和冶炼周期模型,分析了AOD炉冶炼周期随着铁水比和废钢比的变化趋势,得出冶炼周期最短时的炉料结构。结果表明:电炉不锈钢母液加铁水冶炼时,冶炼周期随着铁水比的增加而增加。电炉不锈钢母液加废钢

  8. Total Lightning Flash Activity Response to Aerosol over China Area

    Directory of Open Access Journals (Sweden)

    Pengguo Zhao

    2017-01-01

    Full Text Available Twelve years of measurements of aerosol optical depth (AOD, cloud fraction, cloud top height, ice cloud optical thickness and lightning flash density from 2001 to 2012 have been analyzed to investigate the effect of aerosols on electrical activity over an area of China. The results show that increasing aerosol loading inspires the convective intensity, and then increases the lightning flash density. The spatial distribution of the correlation between aerosol loading and electrical activity shows a remarkable regional difference over China. The high-correlation regions embody the positive aerosol microphysical effect on the intensity of the electrical activity, while the large-scale processes may play the main role in convection development and producing lightning in low-correlation regions.

  9. Energetic and exergetic Improvement of geothermal single flash cycle

    Directory of Open Access Journals (Sweden)

    Navid Nazari

    2016-08-01

    Full Text Available This paper presents a detailed analysis of a new method for improving energetic and exergetic efficiencies of single flash cycle. The thermodynamic process of the new method consists of extracting a fraction of hot wellhead geothermal brine for the purpose of superheating saturated steam entering the turbine. Computer programming scripts were developed and optimized based on mathematical proposed models for the different components of the systems. The operating parameters such as separator temperature, geofluid wellhead enthalpy and geothermal source temperature are varied to investigate their effects on both net power output and turbine exhaust quality of the systems. Also, full exergy assessment was performed for the new design. The results of separator temperature optimization revealed that specific net power output of the new design can be boosted up to 8% and turbine exhaust quality can be diminished up to 50% as compared to common single flash cycle. In addition, for wells with higher discharge enthalpy, superheating process improve specific net power output even up to 10%. Finally, it was observed that the overall system exergy efficiency was approximately raised 3%. Article History: Received January 5th 2016; Received in revised form June 25th 2016; Accepted July 3rd 2016; Available online How to Cite This Article: Nazari, N. and Porkhial, S. (2016. Energetic and Exergetic Improvement of Geothermal Single Flash Cycle. Int. Journal of Renewable Energy Development, 5(2,129-138. http://dx.doi.org/10.14710/ijred.5.2.129-138 

  10. Modelling (flash) floods in a Dutch lowland catchment

    Science.gov (United States)

    Brauer, C. C.; Teuling, A. J.; Overeem, A.; van der Velde, Y.; Hazenberg, P.; Warmerdam, P. M. M.; Kloosterman, P.; Uijlenhoet, R.

    2012-04-01

    On 26 August 2010 the eastern part of The Netherlands and the bordering part of Germany were struck by a series of rainfall events. We investigated the unprecedented flash flood triggered by this exceptionally heavy rainfall event (return period > 1000 years) in the 6.5 km2 Hupsel Brook catchment, which has been the experimental watershed employed by Wageningen University since the 1960s. This study improved our understanding of the dynamics of such lowland flash floods and the results have been published in HESS (Brauer et al., 2011). During this extreme event some thresholds became apparent that do not play a role during average conditions and are not incorporated in rainfall-runoff models. We present a detailed analysis of this extreme event, focusing on (1) the measured soil moisture, groundwater and discharge response of the catchment, (2) the thresholds we found, (3) the manner in which these processes and thresholds are incorporated in some well-known conceptual hydrological models and (4) how well these models are able to simulate the rainfall-runoff processes during the 2010 flash flood.

  11. Prediction of the Flash Point of Binary and Ternary Straight-Chain Alkane Mixtures

    Directory of Open Access Journals (Sweden)

    X. Li

    2014-01-01

    Full Text Available The flash point is an important physical property used to estimate the fire hazard of a flammable liquid. To avoid the occurrence of fire or explosion, many models are used to predict the flash point; however, these models are complex, and the calculation process is cumbersome. For pure flammable substances, the research for predicting the flash point is systematic and comprehensive. For multicomponent mixtures, especially a hydrocarbon mixture, the current research is insufficient to predict the flash point. In this study, a model was developed to predict the flash point of straight-chain alkane mixtures using a simple calculation process. The pressure, activity coefficient, and other associated physicochemical parameters are not required for the calculation in the proposed model. A series of flash points of binary and ternary mixtures of straight-chain alkanes were determined. The results of the model present consistent experimental results with an average absolute deviation for the binary mixtures of 0.7% or lower and an average absolute deviation for the ternary mixtures of 1.03% or lower.

  12. Parietal disruption alters audiovisual binding in the sound-induced flash illusion.

    Science.gov (United States)

    Kamke, Marc R; Vieth, Harrison E; Cottrell, David; Mattingley, Jason B

    2012-09-01

    Selective attention and multisensory integration are fundamental to perception, but little is known about whether, or under what circumstances, these processes interact to shape conscious awareness. Here, we used transcranial magnetic stimulation (TMS) to investigate the causal role of attention-related brain networks in multisensory integration between visual and auditory stimuli in the sound-induced flash illusion. The flash illusion is a widely studied multisensory phenomenon in which a single flash of light is falsely perceived as multiple flashes in the presence of irrelevant sounds. We investigated the hypothesis that extrastriate regions involved in selective attention, specifically within the right parietal cortex, exert an influence on the multisensory integrative processes that cause the flash illusion. We found that disruption of the right angular gyrus, but not of the adjacent supramarginal gyrus or of a sensory control site, enhanced participants' veridical perception of the multisensory events, thereby reducing their susceptibility to the illusion. Our findings suggest that the same parietal networks that normally act to enhance perception of attended events also play a role in the binding of auditory and visual stimuli in the sound-induced flash illusion.

  13. Flash Point: Evaluation, Experimentation and Estimation

    Science.gov (United States)

    Rowley, J. R.; Freeman, D. K.; Rowley, R. L.; Oscarson, J. L.; Giles, N. F.; Wilding, W. V.

    2010-05-01

    The flash point is an important indicator of the flammability of a chemical. For safety purposes, many data compilations report the lowest value and not the most likely. This practice, combined with improper documentation and poor data storage methods, has resulted in compilations filled with fire-hazard data that are inconsistent with related properties and between members of homologous chemical series. In this study, the flash points reported in the DIPPR® 801 database and more than 1,400 other literature values were critically reviewed based on measurement method, inter-property relations, and trends in chemical series. New measurements for seven compounds illustrate the differences between experimental flash points and data commonly found in fire-hazard compilations. With a critically reviewed set of experimental data, published predictive methods for the flash point were evaluated for accuracy.

  14. 3D Flash LIDAR Space Laser Project

    Data.gov (United States)

    National Aeronautics and Space Administration — Advanced Scientific Concepts, Inc (ASC) is a small business, which has developed a compact, eye-safe 3D Flash LIDARTM Camera (FLC) well suited for real-time...

  15. Hot Flashes amd Night Sweats (PDQ)

    Science.gov (United States)

    ... Other Funding Find NCI funding for small business innovation, technology transfer, and contracts Training Cancer Training at ... remedies for hot flashes. These include dong quai , milk thistle , red clover , licorice root extract , and chaste ...

  16. Economic assessment of flash co-pyrolysis of short rotation coppice and biopolymer waste streams.

    Science.gov (United States)

    Kuppens, T; Cornelissen, T; Carleer, R; Yperman, J; Schreurs, S; Jans, M; Thewys, T

    2010-12-01

    The disposal problem associated with phytoextraction of farmland polluted with heavy metals by means of willow requires a biomass conversion technique which meets both ecological and economical needs. Combustion and gasification of willow require special and costly flue gas treatment to avoid re-emission of the metals in the atmosphere, whereas flash pyrolysis mainly results in the production of (almost) metal free bio-oil with a relatively high water content. Flash co-pyrolysis of biomass and waste of biopolymers synergistically improves the characteristics of the pyrolysis process: e.g. reduction of the water content of the bio-oil, more bio-oil and less char production and an increase of the HHV of the oil. This research paper investigates the economic consequences of the synergistic effects of flash co-pyrolysis of 1:1 w/w ratio blends of willow and different biopolymer waste streams via cost-benefit analysis and Monte Carlo simulations taking into account uncertainties. In all cases economic opportunities of flash co-pyrolysis of biomass with biopolymer waste are improved compared to flash pyrolysis of pure willow. Of all the biopolymers under investigation, polyhydroxybutyrate (PHB) is the most promising, followed by Eastar, Biopearls, potato starch, polylactic acid (PLA), corn starch and Solanyl in order of decreasing profits. Taking into account uncertainties, flash co-pyrolysis is expected to be cheaper than composting biopolymer waste streams, except for corn starch. If uncertainty increases, composting also becomes more interesting than flash co-pyrolysis for waste of Solanyl. If the investment expenditure is 15% higher in practice than estimated, the preference for flash co-pyrolysis compared to composting biopolymer waste becomes less clear. Only when the system of green current certificates is dismissed, composting clearly is a much cheaper processing technique for disposing of biopolymer waste.

  17. Method for programming a flash memory

    Science.gov (United States)

    Brosky, Alexander R.; Locke, William N.; Maher, Conrado M.

    2016-08-23

    A method of programming a flash memory is described. The method includes partitioning a flash memory into a first group having a first level of write-protection, a second group having a second level of write-protection, and a third group having a third level of write-protection. The write-protection of the second and third groups is disabled using an installation adapter. The third group is programmed using a Software Installation Device.

  18. Chukai Smelting Co.,Ltd.of Hubei Province Launched the Lead Recycling Project

    Institute of Scientific and Technical Information of China (English)

    2008-01-01

    <正>Chukai Smelting Co.,Ltd.of Hubei Province launched its recycling project of lead-acid stor- age battery in Laohekou City in July.With an annual dealing capacity of 100,000 tons of waste lead-acid storage battery,this project is expected to contribute 60,000 tons of recycled lead,5,000 tons of recycled plastic particulates, 6,000 tons of vitriol electrolyte and 9,000 tons of sodium sulfate crystal.

  19. The factors influencing urinary arsenic excretion and metabolism of workers in steel and iron smelting foundry.

    Science.gov (United States)

    Shuhua, Xi; Qingshan, Sun; Fei, Wang; Shengnan, Liu; Ling, Yan; Lin, Zhang; Yingli, Song; Nan, Yan; Guifan, Sun

    2014-01-01

    In order to evaluate the degree of arsenic (As) exposure and the factors influencing urinary As excretion and metabolism, 192 workers from a steel and iron smelting plant, with different type of work in production such as roller, steel smelting, iron smelting and metallic charge preparation, were recruited. Information about characteristics of each subject was obtained by questionnaire and inorganic As (iAs), monomethylarsonic acid (MMA), dimethylarsinic acid (DMA) in urine were determined. The results showed that steel smelters had significantly higher concentrations of DMA and total As (TAs) than rollers and metallic charge preparation workers, and iron and steel smelters had a higher value of primary methylation index and lower proportion of the iAs (iAs%) than rollers and metallic charge preparation workers. In steel smelters, urinary As level exceeded the biological exposure index (BEI) limit for urinary As of 35 μg/l by 65.52%, and higher than metallic charge preparation workers (35.14%). The individuals consumed seafood in recent 3 days had a higher TAs than the individuals without seafood consumption. Multivariate logistic regression analysis showed that different jobs, taken Chinese medicine of bezoar and seafood consumption in recent 3 days were significantly associated with urinary TAs exceeded BEI limit value 35 μg/l. Our results suggest that workers in steel and iron smelting plant had a lower level of As exposure, and seafood consumption and taking Chinese medicine of bezoar also could increase the risk of urinary TAs exceeded BEI limit value.

  20. Heavy rainfall induced flash flood management

    Science.gov (United States)

    Weiler, Markus; Steinbrich, Andreas; Stölzle, Michael; Leistert, Hannes

    2016-04-01

    Heavy rain induced flash floods are still a serious hazard. In context of climate change even a rise of threat potential of flash flood must be suspected. To improve prediction of endangered areas hydraulic models was developed in the past that implement topography information in heigh resolution, gathered by laser scan applications. To run such models it is crucial to estimate the runoff input spatial distributed. However, this information is usually derived with relatively simple models lacking the process rigour that is required for prediction in engaged basins. Though available rain runoff models are able to model runoff response integral for measured catchments they do not indicate the spatial distribution of processes. Moreover they are commonly calibrated to measured runoff data and not applicable in other environments. Since runoff generation is commonly not measured, a calibration on it is hardly possible. In this study, we present a new approach for quantification of runoff generation in height spatial and temporal resolution. A suited model needs to work without calibration in every given environment under any given conditions. It is possible to develop such a model by combining spatial distributed input data of land surface properties (e.g. soil, geology, land use, …) with worldwide findings of runoff generation research. We developed such a model for the state of Baden-Württemberg, what has an extensive pool of spatial data. E.g. a digital elevation model of 1*1m² resolution, degree of sealing of the earth surface in 1*1m² resolution, soil properties (1:50.000) and geology (1:200.000). Within the state of Baden-Württemberg different regions are situated, with distinct environmental characteristics concerning as well climate, soil properties, land use, topography and geology. The model was tested and validated by modelling 36 observed flood events in 13 mesoscale catchments representing the different regions of Baden-Württemberg as well as by

  1. Hydrodynamic simulations of the core helium flash

    CERN Document Server

    Mocak, M; Weiss, A; Kifonidis, K; 10.1017/S1743921308022813

    2009-01-01

    We describe and discuss hydrodynamic simulations of the core helium flash using an initial model of a 1.25 M_sol star with a metallicity of 0.02 near at its peak. Past research concerned with the dynamics of the core helium flash is inconclusive. Its results range from a confirmation of the standard picture, where the star remains in hydrostatic equilibrium during the flash (Deupree 1996), to a disruption or a significant mass loss of the star (Edwards 1969; Cole & Deupree 1980). However, the most recent multidimensional hydrodynamic study (Dearborn 2006) suggests a quiescent behavior of the core helium flash and seems to rule out an explosive scenario. Here we present partial results of a new comprehensive study of the core helium flash, which seem to confirm this qualitative behavior and give a better insight into operation of the convection zone powered by helium burning during the flash. The hydrodynamic evolution is followed on a computational grid in spherical coordinates using our new version of th...

  2. The free-electron laser FLASH

    Institute of Scientific and Technical Information of China (English)

    Siegfried Schreiber; Bart Faatz

    2015-01-01

    FLASH at DESY, Hamburg, Germany is the first free-electron laser(FEL) operating in the extreme ultraviolet(EUV)and soft x-ray wavelength range. FLASH is a user facility providing femtosecond short pulses with an unprecedented peak and average brilliance, opening new scientific opportunities in many disciplines. The first call for user experiments has been launched in 2005. The FLASH linear accelerator is based on TESLA superconducting technology, providing several thousands of photon pulses per second to user experiments. Probing femtosecond-scale dynamics in atomic and molecular reactions using, for instance, a combination of x-ray and optical pulses in a pump and probe arrangement,as well as single-shot diffraction imaging of biological objects and molecules, are typical experiments performed at the facility. We give an overview of the FLASH facility, and describe the basic principles of the accelerator. Recently,FLASH has been extended by a second undulator beamline(FLASH2) operated in parallel to the first beamline, extending the capacity of the facility by a factor of two.

  3. Environmental geochemistry and ecological risk of vanadium pollution in Panzhihua mining and smelting area, Sichuan, China

    Institute of Scientific and Technical Information of China (English)

    TENG Yanguo; NI Shijun; ZHANG Chengjiang; WANG Jinsheng; LIN Xueyu; HUANG Yi

    2006-01-01

    Vanadium is a trace element widely distributed in the Earth's crust. Naturally high levels of vanadium are recognized mainly in basic rocks and minerals, particularly in titaniferous magnetite. And the anthropogenic sources of vanadium include fossil fuel combustion and wastes including steel-industry slags. In the last few years, the authors have made investigations and assessments on the environmental geochemistry and ecological risk of vanadium in the Panzhihua mining and smelting area. In the study area, anthropogenic vanadium resulted from mining, extracting and smelting of V-Ti magnetite; vanadium pollution of topsoil and sediments occurs mainly in the mining and extracting area, smelting area, slag dumping area, tailing dam and coal mining area. In the soil, the chemical speciation of vanadium shows: insoluble residue>organically bound>Fe (amorphous) oxide-bound>Mn oxide-bound>soluble component. Vanadium pollution can cause potential harmful effects on ecological systems, and lead to animal poisoning and human disease. So vanadiam pollution should be monitored on a regular basis in the Panzhihua area.

  4. The impact of red light running camera flashes on younger and older drivers' attention and oculomotor control.

    Science.gov (United States)

    Wright, Timothy J; Vitale, Thomas; Boot, Walter R; Charness, Neil

    2015-12-01

    Recent empirical evidence has suggested that the flashes associated with red light running cameras (RLRCs) distract younger drivers, pulling attention away from the roadway and delaying processing of safety-relevant events. Considering the perceptual and attentional declines that occur with age, older drivers may be especially susceptible to the distracting effects of RLRC flashes, particularly in situations in which the flash is more salient (a bright flash at night compared with the day). The current study examined how age and situational factors potentially influence attention capture by RLRC flashes using covert (cuing effects) and overt (eye movement) indices of capture. We manipulated the salience of the flash by varying its luminance and contrast with respect to the background of the driving scene (either day or night scenes). Results of 2 experiments suggest that simulated RLRC flashes capture observers' attention, but, surprisingly, no age differences in capture were observed. However, an analysis examining early and late eye movements revealed that older adults may have been strategically delaying their eye movements in order to avoid capture. Additionally, older adults took longer to disengage attention following capture, suggesting at least 1 age-related disadvantage in capture situations. Findings have theoretical implications for understanding age differences in attention capture, especially with respect to capture in real-world scenes, and inform future work that should examine how the distracting effects of RLRC flashes influence driver behavior.

  5. 从锌冶炼渣中回收银试验研究%Experimental research on silver recovery from zinc smelting slag

    Institute of Scientific and Technical Information of China (English)

    许宝华; 陈晓波; 孙文祥

    2016-01-01

    某锌冶炼渣中银品位148.3 g/t,其他杂质含量较低。根据其性质,通过试验研究,采用加入碱磨矿后洗矿—氰化浸出—锌粉置换工艺处理,银的氰化浸出率达到85%以上,锌粉置换率99%以上,获得了较好试验指标;这为开发利用该锌冶炼渣提供了技术依据。%The zinc smelting slag has low content of impurities and a silver grade of 148.3 g/t.According to its property,the experimental research carried out grinding with addition of alkali before a washing-cyanide leaching-zinc replacement process.The silver leaching rate reached over 85%and the replacement rate over 99%,achieving a satisfactory index.The research provides technical reference for the utilization of zinc smelting slag.

  6. Arsenic recovery from roasting fumes of gold smelting%黄金冶炼焙烧烟气中砷的回收

    Institute of Scientific and Technical Information of China (English)

    王金生; 连海瑛; 蹇令兰; 薛树斌; 侯金刚; 董凤书

    2013-01-01

    采用二段焙烧法对含砷复杂金精矿进行预处理,且回收烟气中的As2 O3。通过潼关中金冶炼有限责任公司生产实践,介绍了黄金冶炼焙烧烟气中砷回收的工艺,分析了砷回收系统的设备特点、操作技术条件以及重要的技术参数,为含砷金精矿预处理工艺的环境保护提供了科学依据。%Complex gold concentrates are pretreated with the two-staged roasting method ,and As2 O3 in the fume is recovered.By the practice of Tongguan China National Gold Smelting Co .,Ltd.,the process of recovering arsenic from roasting fumes of gold smelting is introduced .During the introduction ,the equipment characteristics ,operational condi-tions and technical parameters that matter of the recovery system are analyzed ,providing scientific basis for the envi-ronmental protection work through pretreatment of arsenic-containing gold concentrates .

  7. Super Resolution Image Enhancement for a Flash Lidar: Back Projection Method

    Science.gov (United States)

    Bulyshev, Alexander; Hines, Glenn; Vanek, Michael; Amzajerdian, Farzin; Reisse, Robert; Pierrottet, Diego

    2010-01-01

    In this paper a new image processing technique for flash LIDAR data is presented as a potential tool to enable safe and precise spacecraft landings in future robotic or crewed lunar and planetary missions. Flash LIDARs can generate, in real-time, range data that can be interpreted as a 3-dimensional (3-D) image and transformed into a corresponding digital elevation map (DEM). The NASA Autonomous Landing and Hazard Avoidance (ALHAT) project is capitalizing on this new technology by developing, testing and analyzing flash LIDARs to detect hazardous terrain features such as craters, rocks, and slopes during the descent phase of spacecraft landings. Using a flash LIDAR for this application looks very promising, however through theoretical and simulation analysis the ALHAT team has determined that a single frame, or mosaic, of flash LIDAR data may not be sufficient to build a landing site DEM with acceptable spatial resolution, precision, size, or for a mosaic, in time, to meet current system requirements. One way to overcome this potential limitation is by enhancing the flash LIDAR output images. We propose a new super-resolution algorithm applicable to flash LIDAR range data that will create a DEM with sufficient accuracy, precision and size to meet current ALHAT requirements. The performance of our super-resolution algorithm is analyzed by processing data generated during a series of simulation runs by a high fidelity model of a flash LIDAR imaging a high resolution synthetic lunar elevation map. The flash LIDAR model is attached to a simulated spacecraft by a gimbal that points the LIDAR to a target landing site. For each simulation run, a sequence of flash LIDAR frames is recorded and processed as the spacecraft descends toward the landing site. Each run has a different trajectory profile with varying LIDAR look angles of the terrain. We process the output LIDAR frames using our SR algorithm and the results show that the achieved level of accuracy and precision of

  8. Increased Expression of CCN2 in the Red Flashing Light-Induced Myopia in Guinea Pigs

    Directory of Open Access Journals (Sweden)

    Hong Wang

    2013-01-01

    Full Text Available Visual environment plays an important role in the occurrence of myopia. We previously showed that the different flashing lights could result in distinct effects on the ocular growth and development of myopia. CCN2 has been reported to regulate various cellular functions and biological processes. However, whether CCN2 signaling was involved in the red flashing light-induced myopia still remains unknown. In the present study, we investigated the effects of the red flashing lights exposure on the refraction and axial length of the eyes in vivo and then evaluated their effects on the expression of CCN2 and TGF-β in sclera tissues. Our data showed that the eyes exposed to the red flashing light became more myopic with a significant increase of the axial length and decrease of the refraction. Both CCN2 and TGF-β, as well as p38 MAPK and PI3K, were highly expressed in the sclera tissues exposed to the red flashing light. Both CCN2 and TGF-β were found to have the same gene expression profile in vivo. In conclusion, our findings found that CCN2 signaling pathway plays an important role in the red flashing light-induced myopia in vivo. Moreover, our study establishes a useful animal model for experimental myopia research.

  9. On the Mechanism of Microwave Flash Sintering of Ceramics

    Directory of Open Access Journals (Sweden)

    Yury V. Bykov

    2016-08-01

    Full Text Available The results of a study of ultra-rapid (flash sintering of oxide ceramic materials under microwave heating with high absorbed power per unit volume of material (10–500 W/cm3 are presented. Ceramic samples of various compositions—Al2O3; Y2O3; MgAl2O4; and Yb(LaO2O3—were sintered using a 24 GHz gyrotron system to a density above 0.98–0.99 of the theoretical value in 0.5–5 min without isothermal hold. An analysis of the experimental data (microwave power; heating and cooling rates along with microstructure characterization provided an insight into the mechanism of flash sintering. Flash sintering occurs when the processing conditions—including the temperature of the sample; the properties of thermal insulation; and the intensity of microwave radiation—facilitate the development of thermal runaway due to an Arrhenius-type dependency of the material’s effective conductivity on temperature. The proper control over the thermal runaway effect is provided by fast regulation of the microwave power. The elevated concentration of defects and impurities in the boundary regions of the grains leads to localized preferential absorption of microwave radiation and results in grain boundary softening/pre-melting. The rapid densification of the granular medium with a reduced viscosity of the grain boundary phase occurs via rotation and sliding of the grains which accommodate their shape due to fast diffusion mass transport through the (quasi-liquid phase. The same mechanism based on a thermal runaway under volumetric heating can be relevant for the effect of flash sintering of various oxide ceramics under a dc/ac voltage applied to the sample.

  10. An Evaluation of Lightning Flash Rate Parameterizations Based on Observations of Colorado Storms during DC3

    Science.gov (United States)

    Basarab, B.; Fuchs, B.; Rutledge, S. A.

    2013-12-01

    Predicting lightning activity in thunderstorms is important in order to accurately quantify the production of nitrogen oxides (NOx = NO + NO2) by lightning (LNOx). Lightning is an important global source of NOx, and since NOx is a chemical precursor to ozone, the climatological impacts of LNOx could be significant. Many cloud-resolving models rely on parameterizations to predict lightning and LNOx since the processes leading to charge separation and lightning discharge are not yet fully understood. This study evaluates predicted flash rates based on existing lightning parameterizations against flash rates observed for Colorado storms during the Deep Convective Clouds and Chemistry Experiment (DC3). Evaluating lightning parameterizations against storm observations is a useful way to possibly improve the prediction of flash rates and LNOx in models. Additionally, since convective storms that form in the eastern plains of Colorado can be different thermodynamically and electrically from storms in other regions, it is useful to test existing parameterizations against observations from these storms. We present an analysis of the dynamics, microphysics, and lightning characteristics of two case studies, severe storms that developed on 6 and 7 June 2012. This analysis includes dual-Doppler derived horizontal and vertical velocities, a hydrometeor identification based on polarimetric radar variables using the CSU-CHILL radar, and insight into the charge structure using observations from the northern Colorado Lightning Mapping Array (LMA). Flash rates were inferred from the LMA data using a flash counting algorithm. We have calculated various microphysical and dynamical parameters for these storms that have been used in empirical flash rate parameterizations. In particular, maximum vertical velocity has been used to predict flash rates in some cloud-resolving chemistry simulations. We diagnose flash rates for the 6 and 7 June storms using this parameterization and compare

  11. Flash lidar performance testing: configuration and results

    Science.gov (United States)

    Poberezhskiy, Ilya; Johnson, Andrew; Chang, Daniel; Ek, Eric; Natzic, David; Spiers, Gary; Penniman, Steve; Short, Brad

    2012-06-01

    Future planetary and lunar landers can benefit from a hazard detection (HD) system that employs a lidar to create a highresolution 3D terrain map in the vicinity of the landing site and an onboard computer to process the lidar data and identify the safest landing site within the surveyed area. A divert maneuver would then be executed to land in this safe site. An HD system enables landing in regions with a relatively high hazard abundance that would otherwise be considered unacceptably risky, but are of high interest to the scientific community. A key component of a HD system is a lidar with the ability to generate a 3D terrain image with the required range precision in the prescribed time and fits within the project resource constraints. In this paper, we present the results obtained during performance testing of a prototype "GoldenEye" 3D flash lidar developed by ASC, Inc. The testing was performed at JPL with the lidar and the targets separated by 200 m. The analysis of the lidar performance obtained for different target types and albedos, pulse energies, and fields of view is presented and compared to key HD lidar requirements identified for the Mars 2018 lander.

  12. Studying white dwarf merger remnants with FLASH

    Science.gov (United States)

    Jenks, Malia

    2017-01-01

    There is still uncertainty as to the progenitor systems of type Ia supernova (SN Ia). Both single and double degenerate systems have been suggested as progenitors. In a double degenerate system a merger between the two white dwarfs, with total mass at or exceeding the Chandrasekhar mass, leads to the supernova. If the explosion occurs during the merging process it is a violent merger. If an explosion doesn't occur while the stars merge the system becomes a white dwarf of unstable mass. For mergers of this type with differing starting masses it has been shown that during the viscous evolution carbon burning starts far from the center and stably converts the star to oxygen and neon. In this case the star will eventually collapse to a neutron star and not produce an SN Ia. The case of similar mass mergers has been much less explored. Using the results of a smooth particle hydrodynamic merger we simulate the viscous evolution of models of different mass ratios with FLASH. These simulations test if a similar mass merger can lead to an SN Ia, and begin to probe where the transition from similar to dissimilar mass occurs.

  13. FPGA Flash Memory High Speed Data Acquisition

    Science.gov (United States)

    Gonzalez, April

    2013-01-01

    The purpose of this research is to design and implement a VHDL ONFI Controller module for a Modular Instrumentation System. The goal of the Modular Instrumentation System will be to have a low power device that will store data and send the data at a low speed to a processor. The benefit of such a system will give an advantage over other purchased binary IP due to the capability of allowing NASA to re-use and modify the memory controller module. To accomplish the performance criteria of a low power system, an in house auxiliary board (Flash/ADC board), FPGA development kit, debug board, and modular instrumentation board will be jointly used for the data acquisition. The Flash/ADC board contains four, 1 MSPS, input channel signals and an Open NAND Flash memory module with an analog to digital converter. The ADC, data bits, and control line signals from the board are sent to an Microsemi/Actel FPGA development kit for VHDL programming of the flash memory WRITE, READ, READ STATUS, ERASE, and RESET operation waveforms using Libero software. The debug board will be used for verification of the analog input signal and be able to communicate via serial interface with the module instrumentation. The scope of the new controller module was to find and develop an ONFI controller with the debug board layout designed and completed for manufacture. Successful flash memory operation waveform test routines were completed, simulated, and tested to work on the FPGA board. Through connection of the Flash/ADC board with the FPGA, it was found that the device specifications were not being meet with Vdd reaching half of its voltage. Further testing showed that it was the manufactured Flash/ADC board that contained a misalignment with the ONFI memory module traces. The errors proved to be too great to fix in the time limit set for the project.

  14. Single Particle Difraction at FLASH

    Energy Technology Data Exchange (ETDEWEB)

    Bogan, M.; Boutet, S.; Starodub, Dmitri; Decorwin-Martin, Philippe; /SLAC; Chapman, H.; Bajt, S.; Schulz, J.; /DESY; Hajdu, Janos; Seibert, M.M.; Iwan, Bianca; Timneanu, Nicusor; /Uppsala U.; Marchesini, Stefano; /LBL, Berkeley; Barty, Anton; Benner, W.Henry; Frank, Matthias; Hau-Riege, Stefan P.; Woods, Bruce; /LLNL, Livermore; Rohner, Urs; /Tofwerk AG, Thun

    2010-06-11

    Single-pulse coherent diffraction patterns have been collected from randomly injected single particles with a soft X-ray free-electron laser (FEL). The intense focused FEL pulse gives a high-resolution low-noise coherent diffraction pattern of the object before that object turns into a plasma and explodes. A diffraction pattern of a single particle will only be recorded when the particle arrival into the FEL interaction region coincides with FEL pulse arrival and detector integration. The properties of the experimental apparatus coinciding with these three events set the data acquisition rate. For our single particle FLASH diffraction imaging experiments: (1) an aerodynamic lens stack prepared a particle beam that consisted of particles moving at 150-200 m/s positioned randomly in space and time, (2) the 10 fs long FEL pulses were delivered at a fixed rate, and (3) the detector was set to integrate and readout once every two seconds. The effect of these experimental parameters on the rate of data acquisition using randomly injected particles will be discussed. Overall, the ultrashort FEL pulses do not set the limit of the data acquisition, more important is the effective interaction time of the particle crossing the FEL focus, the pulse sequence structure and the detector readout rate. Example diffraction patterns of randomly injected ellipsoidal iron oxide nanoparticles in different orientations are presented. This is the first single particle diffraction data set of identical particles in different orientations collected on a shot-to-shot basis. This data set will be used to test algorithms for recovering 3D structure from single particle diffraction.

  15. Karst flash floods: an example from the Dinaric karst (Croatia

    Directory of Open Access Journals (Sweden)

    O. Bonacci

    2006-01-01

    Full Text Available Flash floods constitute one of the deadliest and costliest natural disasters worldwide. This paper explains the karst flash flood phenomenon, which represents a special kind of flash flood. As the majority of flash floods karst flash floods are caused by intensive short-term precipitation in an area whose surface rarely exceeds a few square kilometres. The characteristics of all flash floods are their short duration, small areal extent, high flood peaks and rapid flows, and heavy loss of life and property. Karst flash floods have specific characteristics due to special conditions for water circulation, which exist in karst terrains. During karst flash floods a sudden rise of groundwater levels occurs, which causes the appearance of numerous, unexpected, abundant and temporary karst springs. This paper presents in detail an example of a karst flash flood in the Marina bay (Dinaric karst region of Croatia, which occurred in December 2004.

  16. Flash flood modeling with the MARINE hydrological distributed model

    Directory of Open Access Journals (Sweden)

    V. Estupina-Borrell

    2006-11-01

    Full Text Available Flash floods are characterized by their violence and the rapidity of their occurrence. Because these events are rare and unpredictable, but also fast and intense, their anticipation with sufficient lead time for warning and broadcasting is a primary subject of research. Because of the heterogeneities of the rain and of the behavior of the surface, spatially distributed hydrological models can lead to a better understanding of the processes and so on they can contribute to a better forecasting of flash flood. Our main goal here is to develop an operational and robust methodology for flash flood forecasting. This methodology should provide relevant data (information about flood evolution on short time scales, and should be applicable even in locations where direct observations are sparse (e.g. absence of historical and modern rainfalls and streamflows in small mountainous watersheds. The flash flood forecast is obtained by the physically based, space-time distributed hydrological model "MARINE'' (Model of Anticipation of Runoff and INondations for Extreme events. This model is presented and tested in this paper for a real flash flood event. The model consists in two steps, or two components: the first component is a "basin'' flood module which generates flood runoff in the upstream part of the watershed, and the second component is the "stream network'' module, which propagates the flood in the main river and its subsidiaries. The basin flash flood generation model is a rainfall-runoff model that can integrate remotely sensed data. Surface hydraulics equations are solved with enough simplifying hypotheses to allow real time exploitation. The minimum data required by the model are: (i the Digital Elevation Model, used to calculate slopes that generate runoff, it can be issued from satellite imagery (SPOT or from French Geographical Institute (IGN; (ii the rainfall data from meteorological radar, observed or

  17. A Comparative Study of Reduced-Variables-Based Flash and Conventional Flash

    DEFF Research Database (Denmark)

    Yan, Wei; Stenby, Erling Halfdan; Michelsen, Michael Locht

    2013-01-01

    the advantages of the reduced-variables methods in their recent paper. A fair comparison between the reduced-variables-based flash and the conventional flash is not straightforward because it is difficult to formulate the former as unconstrained minimization problems, and the flash calculation time is also...... related to the implementation quality. With the recent formulations by Nichita and Graciaa (2011), it is possible to code the reduced-variables methods without extensive modifications of Michelsen's conventional flash algorithm. A minimization-based reduced-variables algorithm was coded and compared...... with the conventional minimization-based flash. A test with the use of the SPE 3 example (Kenyon and Behie 1987) showed that the best reduction in time was less than 20% for the extreme situation of 25 components and just one row/column with nonzero BIPs. A better performance can be achieved by a simpler implementation...

  18. Ultra-High Speed Fabrication of TiO2 Photoanode by Flash Light for Dye-Sensitized Solar Cell.

    Science.gov (United States)

    Hwang, Hyun-Jun; Kim, Hak-Sung

    2015-07-01

    In this work, a new way to fabricate nanoporous TiO2 photoanode by flash light is demonstrated. TiO2 nanoparticles are sintered on FTO glass by flash light irradiation at room temperature in ambient condition, which is dramatically simple, ultrahigh speed and one-shot large area fabrication process compared to a conventional high temperature (120 °C) thermal sintering process. The effect of the flash light conditions (flash light energy, pulse numbers and pulse duration) on the nanostructures of sintered TiO2 layer, was studied and discussed using several microscopic and spectroscopic characterization techniques such as SEM, FT-IR, XRD and XPS. The sintered TiO2 photoanodes by flash light were used in DSSC and its performance were compared with that of DSSC fabricated by conventional thermal sintering process. It was found that a flash light sintered TiO2 photoanode has efficiency which is similar to that of the thermal sintered photoanode. It is expected that the newly developed flash light sintering technique of TiO2 nanoparticles would be a strong alternative to realize the room temperature and in-situ sintering of photoanode fabrication for outdoor solar cell fabrication.

  19. Analysis on the Courses of Blocked Pipe in the Flash Evaporator of the NaCl/Na2SO4 Evaporation Processes%盐硝联产工艺闪发器堵管成因浅析

    Institute of Scientific and Technical Information of China (English)

    万学东

    2001-01-01

    苏尔寿·埃雪维斯公司盐硝联产工艺装置,在运行过程中,硝系统闪发器结盐垢堵管,严重影响正常生产。本文从形成盐垢的现象、成因、机理进行了分析,并结合生产实际,提出了控制和防范措施。%Sulzer Escher Wyss NaCl/Na2SO4 evaporation plant on revolving pipe is blocked by scaling salt in the sulfate system's flash evaporator, it effects normal revolve. This papers analysis on the phenomenon the course and principle of scaling salt. Think operations over, author suggests control and prevent treatment.

  20. Lightning flash multiplicity in eastern Mediterranean thunderstorms

    Science.gov (United States)

    Yair, Y.; Shalev, S.; Erlich, Z.; Agrachov, A.; Katz, E.; Saaroni, H.; Price, C.; Ziv, B.

    2014-02-01

    Cloud-to-ground lightning flashes usually consist of one or several strokes coming in very short temporal succession and close spatial proximity. A commonly used method for converting stroke data into flashes is using the National Lightning Detection Network (NLDN) thresholds of maximum temporal separation of 0.5 s and maximum lateral distance of 10 km radius between successive strokes. In the present study, we tested a location-based algorithm with several spatial and temporal ranges, and analyzed stroke data obtained by the Israel Lightning Location System (ILLS) during one year (1.8.2009-31.7.2010). We computed the multiplicity, the percentage of single stroke flashes and the geographical distribution of average multiplicity values for thunderstorms in the Eastern Mediterranean region. Results show that for the NLDN thresholds, the percentage of single stroke flashes in Israel was 37% and the average multiplicity was 1.7. We reanalyzed the data with a spatial range that equals twice the ILLS location error and shorter times. For the new thresholds of maximum distance of 2.5 km and maximum allowed temporal separation of 0.2 s we find that the mean multiplicity of negative CGs is lowered to 1.4 and find a percentage of 58% of single stroke flashes. A unique severe storm from 30 October 2009 is analyzed and compared with the annual average of 2009/2010, showing that large deviations from the mean values can occur in specific events.

  1. Study on Flash-type Extraction Process for Total Flavonoids and Icariin from Herba Epimedii%淫羊藿中淫羊藿苷和总黄酮的闪式提取工艺

    Institute of Scientific and Technical Information of China (English)

    贺石麟; 牛景霞; 倪艳

    2011-01-01

    Objective: To study and optimize the extraction and preparation technics of icariin and total flavonoids by orthogonal design. Method: The best conditions of extracting icariin and total flavonoids from Herba Epimed by flash-type extraction were screened by using method of orthogonal design and selecting the amount of icariin and total flavonoids as index. Result: The effect influencing factors of flash-type extraction were as follows:extraction times > duration of extraction > ratio of solid to liquid > concentration of ethanol. The optimum extraction condition obtained was: 10 minutes and 3 times, ratio of solid to liquid 1:25, 50% ethanol. Conclusion: Flashtype extraction was found to be an efficient and rapid method for extracting total flavonoids and icariin from Herba Epimedii.%目的:研究闪式提取法对淫羊藿中淫羊霍苷和总黄酮的最佳提取工艺条件.方法:以淫羊藿苷和总黄酮含量为指标,通过正交试验得出闪式提取法提取其淫羊藿苷和总黄酮的最优条件.结果:闪式提取法各因素对总黄酮和淫羊藿苷提取效果的影响程度依次为:提取次数>提取时间>液固比>乙醇体积分数,最佳提取工艺为:加25倍量50%乙醇提取3次,每次10 min.结论:闪式提取法是一种高效、快速提取淫羊藿中总黄酮和淫羊藿苷的方法.

  2. Smelting Magnesium Metal using a Microwave Pidgeon Method

    Science.gov (United States)

    Wada, Yuji; Fujii, Satoshi; Suzuki, Eiichi; Maitani, Masato M.; Tsubaki, Shuntaro; Chonan, Satoshi; Fukui, Miho; Inazu, Naomi

    2017-04-01

    Magnesium (Mg) is a lightweight metal with applications in transportation and sustainable battery technologies, but its current production through ore reduction using the conventional Pidgeon process emits large amounts of CO2 and particulate matter (PM2.5). In this work, a novel Pidgeon process driven by microwaves has been developed to produce Mg metal with less energy consumption and no direct CO2 emission. An antenna structure consisting of dolomite as the Mg source and a ferrosilicon antenna as the reducing material was used to confine microwave energy emitted from a magnetron installed in a microwave oven to produce a practical amount of pure Mg metal. This microwave Pidgeon process with an antenna configuration made it possible to produce Mg with an energy consumption of 58.6 GJ/t, corresponding to a 68.6% reduction when compared to the conventional method.

  3. In situ monitoring of flash-light sintering of copper nanoparticle ink for printed electronics

    Science.gov (United States)

    Hwang, Hyun-Jun; Chung, Wan-Ho; Kim, Hak-Sung

    2012-12-01

    In this work, a flash-light sintering process for Cu nanoinks was studied. In order to precisely monitor the milliseconds flash-light sintering process, a real-time Wheatstone bridge electrical circuit and a high-rate data acquisition system were used. The effects of several flash-light irradiation conditions (irradiation energy, pulse number, on-time, and off-time) and the effects of the amount of poly(N-vinylpyrrolidone) in the Cu nanoink on the flash-light sintering process were investigated. The microstructures of the sintered Cu films were analyzed by scanning electron microscopy. To investigate the oxidation or reduction of the oxide-covered copper nanoparticles, a crystal phase analysis using x-ray diffraction was performed. In addition, the sheet resistance of Cu film was measured using a four-point probe method. From this study, it was found that the flash-light sintered Cu nanoink films have a conductivity of 72 Ωm/sq without any damage to the polyimide substrate. Similar nanoinks are expected to be widely used in printed and flexible electronics products in the near future.

  4. Two-step flash light sintering of copper nanoparticle ink to remove substrate warping

    Science.gov (United States)

    Ryu, Chung-Hyeon; Joo, Sung-Jun; Kim, Hak-Sung

    2016-10-01

    A two-step flash light sintering process was devised to reduce the warping of polymer substrates during the sintering of copper nanoparticle ink. To determine the optimum sintering conditions of the copper nanoparticle ink, the flash light irradiation conditions (pulse power, pulse number, on-time, and off-time) were varied and optimized. In order to monitor the flash light sintering process, in situ resistance and temperature monitoring of copper nanoink were conducted during the flash light sintering process. Also, a transient heat transfer analysis was performed by using the finite-element program ABAQUS to predict the temperature changes of copper nanoink and polymer substrate. The microstructures of the sintered copper nanoink films were analyzed by scanning electron microscopy. Additionally, an X-ray diffraction and Fourier transform infrared spectroscopy were used to characterize the crystal phase change of the sintered copper nanoparticles. The resulting two-step flash light sintered copper nanoink films exhibited a low resistivity (3.81 μΩ cm, 2.3 times of that of bulk copper) and 5B level of adhesion strength without warping of the polymer substrate.

  5. Fishing for Smelt, Osmerus eperlanus (Linnaeus, 1758 A traditional food fish – possible cuisine in postmodern Sweden?

    Directory of Open Access Journals (Sweden)

    Ingvar Svanberg

    2016-06-01

    Full Text Available For the rural population in Sweden, fishing in lakes and rivers was of great importance until recently. Many fish species served as food or animal fodder, or were used to make glue and other useful products. But the receding of lakes in the nineteenth century, and the expansion of hydropower and worsening of water pollution in the twentieth, contributed to the decline of inland fisheries. At the same time, marine fish became more competitive on the Swedish food market. In some regions, however, certain freshwater species continued to be caught for household consumption well into the twentieth century. One such species was the smelt (Osmerus eperlanus, which fifty years ago was still of economic importance. Nowadays, however, smelt is only caught in very low volumes; its role is therefore insignificant. In neighbouring countries, however – such as Estonia, Lithuania, and Russia – it is still being exploited commercially. In Germany, where water quality has improved in rivers and restaurants have shown increasing interest in smelt, a successful revival for the fish as a regional and seasonal food can be seen. Smelt fishing has dimensions which are not only culinary, but social and cultural as well. Traditional ways of food preparation can be transformed into modern haute cuisine. Smelt fishing has the potential to develop commercially in Sweden also.

  6. Reduced Comparator Flash ADC for ECG Applications

    Directory of Open Access Journals (Sweden)

    Saravanan. V. A

    2013-03-01

    Full Text Available A CMOS based low power 4-bit Flash Analog to Digital Converter (ADC design with reduced number of comparators than the conventional Flash Analog to Digital Converter and multiplexer based architecture is proposed. For improving the conversion rate, both the analog and digital parts of the ADC are fully modified and the architecture uses only 4 comparators instead of 15 as used in conventional flash ADC, thus saving considerable amount of power. The proposed 4-bit ADC is designed and simulated in TANNER tools with 1.2 V supply voltage using TSpice simulation. The proposed design consumes low power of 2.15mW and operates at a faster rate hence it is suitable for ECG applications.

  7. Investigation of Heavy Metals Concentrations in the Water Wells Close to Zanjan Zinc and Lead Smelting Plant

    Directory of Open Access Journals (Sweden)

    M Nourani

    2008-09-01

    Full Text Available Background and Objectives: Heavy metals processing industry has always been a major cause of concern which affects soils, surface waters, ground waters and river sediments contaminations. Thus, the Zanjan Zinc and Lead Smelting Plant has been considered as a potential source of contamination."nMterials and Methods: This cross-sectional study has been conducted in February 2008 in the site region .The concentrations of Lead, Zinc and Cadmium have been assessed. The samples have been taken from 17 wells and atomic absorption spectrophotometeric method has been used to assess the samples. In order to find out and locate the exact situation of the wells under study, Global Positioning System instrument has been used. The correlation between the concentration of each metal and the distance of studied well from the plant has been assessed too."nResults: The findings of this study showed that lead and cadmium concentrations were 53% and 59% respectively out of the guideline values of World Health Organization."nConclusion: The concentration of Zinc was lower than both national and international values in all samples. As the heavy metal concentration is very important for human health status, the other fields of study like heavy metal air pollution effects and related diseases and conditions should be studied and assessed.

  8. Centrally active nonhormonal hot flash therapies.

    Science.gov (United States)

    Loprinzi, Charles L; Stearns, Vered; Barton, Debra

    2005-12-19

    Given the problems associated with hormonal therapy, and the prominent problem of hot flashes in menopausal women, there is a need for nonhormonal agents to alleviate hot flashes. Several compounds that appear to act on the central nervous system have been investigated. Potential mechanisms for their effects on hot flashes have been described. Bellergal (no longer available on the US market, where it was known as Bellergal-S), a combination preparation sedative that consists of low-dose phenobarbital, ergotamine tartrate, and levorotatory alkaloids of belladonna, is an old agent that was popular approximately 20 years ago; however, there is limited suggestion of efficacy for this agent. Clonidine, an older antihypertensive drug, is another centrally active agent that has been studied. Randomized trials have demonstrated that it clearly works for reducing hot flashes, but the magnitude of efficacy is somewhat limited. Toxicity from this agent limits its utility in the clinic. Methyldopa is another centrally active agent that has been studied but to a more limited degree. It appears to have minimal efficacy and too much toxicity to make it clinically useful. Anecdotal observations from a number of sources suggested that newer antidepressants can alleviate hot flashes. This led to pilot trials of venlafaxine and paroxetine, with results suggesting benefit from both drugs. Subsequently, randomized, placebo-controlled, double-blind clinical trials of venlafaxine, paroxetine, and fluoxetine were conducted. All 3 of these clinical trials demonstrated statistically significant reductions in hot flashes with these newer antidepressants compared with placebo. Pilot trials of citalopram and mirtazapine, 2 other newer antidepressants, have also suggested efficacy. Toxicity evaluations have suggested that these agents are, again, well tolerated by the majority of patients. A recent trial, however, was unable to demonstrate any benefit for fluoxetine or citalopram over a placebo

  9. Foundation Flash CS5 for Designers

    CERN Document Server

    Green, T

    2010-01-01

    Flash is one of the most engaging, innovative, and versatile technologies available - allowing the creation of anything from animated banners and simple cartoons to Rich Internet Applications, interactive videos, and dynamic user interfaces for web sites, kiosks, devices, or DVDs. The possibilities are endless, and now it just got better. Flash CS5 boasts a host of new features, including better support for mobile devices, a whole new animation engine enabling full manipulation of tweens and paths, custom easing, improved inverse kinematics, a revamped timeline, built-in 3D, and much more. Thi

  10. Dislocation Motion and the Microphysics of Flash Heating and Weakening of Faults during Earthquakes

    Directory of Open Access Journals (Sweden)

    Elena Spagnuolo

    2016-07-01

    Full Text Available Earthquakes are the result of slip along faults and are due to the decrease of rock frictional strength (dynamic weakening with increasing slip and slip rate. Friction experiments simulating the abrupt accelerations (>>10 m/s2, slip rates (~1 m/s, and normal stresses (>>10 MPa expected at the passage of the earthquake rupture along the front of fault patches, measured large fault dynamic weakening for slip rates larger than a critical velocity of 0.01–0.1 m/s. The dynamic weakening corresponds to a decrease of the friction coefficient (defined as the ratio of shear stress vs. normal stress up to 40%–50% after few millimetres of slip (flash weakening, almost independently of rock type. The microstructural evolution of the sliding interfaces with slip may yield hints on the microphysical processes responsible for flash weakening. At the microscopic scale, the frictional strength results from the interaction of micro- to nano-scale surface irregularities (asperities which deform during fault sliding. During flash weakening, the visco-plastic and brittle work on the asperities results in abrupt frictional heating (flash heating and grain size reduction associated with mechano-chemical reactions (e.g., decarbonation in CO2-bearing minerals such as calcite and dolomite; dehydration in water-bearing minerals such as clays, serpentine, etc. and phase transitions (e.g., flash melting in silicate-bearing rocks. However, flash weakening is also associated with grain size reduction down to the nanoscale. Using focused ion beam scanning and transmission electron microscopy, we studied the micro-physical mechanisms associated with flash heating and nanograin formation in carbonate-bearing fault rocks. Experiments were conducted on pre-cut Carrara marble (99.9% calcite cylinders using a rotary shear apparatus at conditions relevant to seismic rupture propagation. Flash heating and weakening in calcite-bearing rocks is associated with a shock-like stress

  11. Smelting reduction of MgO in molten slag by liquid ferrosilicon

    Directory of Open Access Journals (Sweden)

    Tang, Qifeng

    2016-06-01

    Full Text Available The smelting reduction of magnesium oxide was researched in this paper. The effect of molten slag composition and reduction temperature on percent reduction of magnesium oxide were discussed, and kinetics of smelting reduction of magnesium oxide in molten slag was studied. The results showed that the reduction extent of magnesium oxide increased by increasing either one of the following factors: the initial mass ratio of Al2O3/SiO2, the addition of CaF2, the initial molar ratio of Si/2MgO, and reaction temperature. The overall smelting reduction was controlled by mass transfer in slag with an apparent activation energy 586 kJ mol-1.En este trabajo se estudia la reducción de óxido de magnesio. La influencia de la composición de las escorias y de la temperatura de reducción sobre el porcentaje de reducción de óxido de magnesio han sido discutidas, y asimismo se ha estudiado la cinética de la reducción del óxido de magnesio en escorias fundidas. Los resultados muestran que la reducción se incrementa al aumentar alguno de los siguientes factores: la proporción de Al2O3/SiO2, la adición de CaF2, la proporción molar de Si/2MgO y la temperatura de reacción. En general la reducción fue controlada por la transferencia de masa en la escoria con una energía aparente de 586 kJ mol-1.

  12. Assessing individual employee risk factors for occupational asthma in primary aluminium smelting

    Science.gov (United States)

    Barnard, C; McBride, D; Firth, H; Herbison, G

    2004-01-01

    Aims: To assess the significance of individual risk factors in the development of occupational asthma of aluminium smelting (OAAS). Methods: A matched case-control study nested in a cohort of 545 workers employed in areas with moderate to high levels of smelting dust and fume. The cohort comprised those who had their first pre-employment medical examination between 1 July 1982 and 1 July 1995; follow up was until 31 December 2000. Forty five cases diagnosed with OAAS and four controls per case were matched for the same year of pre-employment and age within ±5 years. The pre-employment medical questionnaires were examined, blinded as to case-control status, and information obtained on demographics and details of allergic symptoms, respiratory risk factors, respiratory symptoms, and spirometry. Data from the subsequent medical notes yielded subsequent history of hay fever, family history of asthma, full work history, date of termination or diagnosis, and tobacco smoking history at the end-point. Results: There was a significant positive association between hay fever diagnosed either at or during employment and OAAS (adjusted OR 3.58, 95% CI 1.57 to 8.21). A higher forced expiratory ratio (FEV1/FVC%) at employment reduced the risk of developing OAAS (adjusted OR 0.93, 95% CI 0.88 to 0.99). The risk of OAAS was more than three times higher in individuals with an FER of 70.0–74.9% than in individuals with an FER ⩾80.0% (adjusted OR 3.46, 95% CI 1.01 to 11.89). Conclusions: Individuals with hay fever may be more susceptible to occupational asthma when exposed to airborne irritants in aluminium smelting. The pathological basis may be reduced nasal filtration and increased bronchial hyperresponsiveness. PMID:15208376

  13. Cancer treatment: dealing with hot flashes and night sweats

    Science.gov (United States)

    ... this page: //medlineplus.gov/ency/patientinstructions/000826.htm Cancer treatment: dealing with hot flashes and night sweats To ... this page, please enable JavaScript. Certain types of cancer treatments can cause hot flashes and night sweats. Hot ...

  14. Flash3D EDL Sensor Technology Advancement Project

    Data.gov (United States)

    National Aeronautics and Space Administration — Advanced Scientific Concepts Inc. (ASC) is a small business, which has developed a number of 3D flash LADAR systems. Flash Ladar sensors are 3D video systems that...

  15. 3D Flash LIDAR EDL Resolution Improvement Project

    Data.gov (United States)

    National Aeronautics and Space Administration — Advanced Scientific Concepts, Inc. (ASC) is a small business that has developed 3D Flash LIDAR systems for space and terrestrial applications. 3D Flash LIDAR is...

  16. Sunset science. III. Visual adaptation and green flashes.

    Science.gov (United States)

    Young, A T

    2000-12-01

    Photographs of green flashes do not preclude a role for physiological effects in these phenomena. While green flashes are certainly not after-images, there is compelling evidence that adaptation in the visual system strongly affects the perceived color of most sunset green flashes. Furthermore, the retinal image of the setting Sun is usually bright enough to bleach most of the red-sensitive photopigment in a few seconds, making the yellow stage of a sunset flash appear green. Even in air so hazy that no green light reaches the eye, a yellow flash may occur and appear green. Many, but not all, visual observations of sunset green flashes are of this yellow flash. The yellow portion of sunset green flashes helps explain their reported durations, which exceed those expected for the appearance of green light alone.

  17. The influence of the silicate slag composition on copper losses during smelting of the sulfide concentrates

    Directory of Open Access Journals (Sweden)

    Živković Živan

    2009-01-01

    Full Text Available This paper presents the results of multi-linear regression analysis (MLRA of the slag composition (SiO2, FeO, Fe3O4, CaO, Al2O3 and the content of copper in the matte on resulting copper content in the slag during smelting of the sulfide concentrates in the reverberatory furnace. When comparing results obtained with MLRA model calculations with values measured at industrial level high degree of fitting is obtained (R2 = 0.974. This indicates that slag composition and content of copper in the matte influences the copper losses in the waste slag with the probability of 95 %.

  18. The influence of the silicate slag composition on copper losses during smelting of the sulfide concentrates

    OpenAIRE

    2009-01-01

    This paper presents the results of multi-linear regression analysis (MLRA) of the slag composition (SiO2, FeO, Fe3O4, CaO, Al2O3) and the content of copper in the matte on resulting copper content in the slag during smelting of the sulfide concentrates in the reverberatory furnace. When comparing results obtained with MLRA model calculations with values measured at industrial level high degree of fitting is obtained (R2 = 0.974). This indicates that slag composition and content of copper in t...

  19. Heavy metal removal from copper smelting effluent using electrochemical cylindrical flow reactor.

    Science.gov (United States)

    Ahmed Basha, C; Bhadrinarayana, N S; Anantharaman, N; Meera Sheriffa Begum, K M

    2008-03-21

    The purpose of this study is mainly to evaluate the performance of the continuous recirculation flow cell at low current density and pH (the pH at which the effluents are available) in removing heavy metals from copper smelting effluent by cathodic reduction. During the electrolysis at different pH, % removal of heavy metals removal, energy consumption and heterogeneous reaction rate constants were investigated at given flow rate and current density on the selected industrial effluent. The overall specific energy consumption at the pH 0.64 was observed to be lowest, which is 10.99kWh/kg of heavy metal removal.

  20. Small SWAP 3D imaging flash ladar for small tactical unmanned air systems

    Science.gov (United States)

    Bird, Alan; Anderson, Scott A.; Wojcik, Michael; Budge, Scott E.

    2015-05-01

    The Space Dynamics Laboratory (SDL), working with Naval Research Laboratory (NRL) and industry leaders Advanced Scientific Concepts (ASC) and Hood Technology Corporation, has developed a small SWAP (size, weight, and power) 3D imaging flash ladar (LAser Detection And Ranging) sensor system concept design for small tactical unmanned air systems (STUAS). The design utilizes an ASC 3D flash ladar camera and laser in a Hood Technology gyro-stabilized gimbal system. The design is an autonomous, intelligent, geo-aware sensor system that supplies real-time 3D terrain and target images. Flash ladar and visible camera data are processed at the sensor using a custom digitizer/frame grabber with compression. Mounted in the aft housing are power, controls, processing computers, and GPS/INS. The onboard processor controls pointing and handles image data, detection algorithms and queuing. The small SWAP 3D imaging flash ladar sensor system generates georeferenced terrain and target images with a low probability of false return and <10 cm range accuracy through foliage in real-time. The 3D imaging flash ladar is designed for a STUAS with a complete system SWAP estimate of <9 kg, <0.2 m3 and <350 W power. The system is modeled using LadarSIM, a MATLAB® and Simulink®- based ladar system simulator designed and developed by the Center for Advanced Imaging Ladar (CAIL) at Utah State University. We will present the concept design and modeled performance predictions.

  1. Mainostoimiston Flash-tuotantoprosessin kehittäminen

    OpenAIRE

    Heinonen, Toni

    2012-01-01

    Tämän opinnäytetyön tarkoituksena oli kehittää mainostoimiston Flash-tuotantoprosessia. Mainostoimiston Flash-tuotanto on pääosin display-mainonnan eli bannereiden sekä Flashmainoskampanjasivustojen luontia. Lisäksi tarkoituksena oli tutkia mahdollisuutta soveltaa ohjelmistokehityksessä toimiviksi havaittujen ketterien prosessimallien soveltamista mainostoimiston Flash-tuotantoprosessiin. Työ aloitettiin kuvaamalla mainostoimiston nykyinen Flash-tuotantoprosessi tarkoitukseen ...

  2. Ultrafast-Contactless Flash Sintering using Plasma Electrodes

    OpenAIRE

    Theo Saunders; Salvatore Grasso; Reece, Michael J.

    2016-01-01

    This paper presents a novel derivative of flash sintering, in which contactless flash sintering (CFS) is achieved using plasma electrodes. In this setup, electrical contact with the sample to be sintered is made by two arc plasma electrodes, one on either side, allowing current to pass through the sample. This opens up the possibility of continuous throughput flash sintering. Preheating, a usual precondition for flash sintering, is provided by the arc electrodes which heat the sample to 1400 ...

  3. SNR efficiency of combined bipolar gradient echoes: Comparison of three-dimensional FLASH, MPRAGE, and multiparameter mapping with VFA-FLASH and MP2RAGE.

    Science.gov (United States)

    Jutras, Jean-David; Wachowicz, Keith; Gilbert, Guillaume; De Zanche, Nicola

    2017-06-01

    High-bandwidth bipolar multiecho gradient echo sequences are increasingly popular in structural brain imaging because of reduced water-fat shifts, lower susceptibility effects, and improved signal-to-noise ratio (SNR) efficiency. In this study, we investigated the performance of three three-dimensional multiecho sequences (MPRAGE, MP2RAGE, and FLASH) with scan times technique with multiecho FLASH (VFA-FLASH). Multiecho sequences were optimized to yield equivalent contrast and improved SNR compared with their single-echo counterparts. Theoretical SNR gains were verified with measurements in a multilayered phantom. Robust image processing pipelines extracted PD, T1 , and T2* maps from MP2RAGE or VFA-FLASH, and the corresponding SNR was measured with varying SENSE accelerations (R = 1-5) and number of echoes (N = 1-12). All sequences were tested on four healthy volunteers. Multiecho sequences achieved SNR gains of 1.3-1.6 over single-echo sequences. MP2RAGE yielded comparable T1 -to-noise ratio to VFA-FLASH, but significantly lower SNR (sampling bandwidths. VFA-FLASH surpasses MP2RAGE in its ability to map three parameters with high SNR and 1-mm isotropic resolution in a clinically relevant scan time (∼8:30 min), whereas MP2RAGE yields lower intersubject variability in T1 . Magn Reson Med 77:2186-2202, 2017. © 2016 International Society for Magnetic Resonance in Medicine. © 2016 International Society for Magnetic Resonance in Medicine.

  4. Highly conductive copper nano/microparticles ink via flash light sintering for printed electronics

    Science.gov (United States)

    Joo, Sung-Jun; Hwang, Hyun-Jun; Kim, Hak-Sung

    2014-07-01

    In this study, the size effect of copper particles on the flash light sintering of copper (Cu) ink was investigated using Cu nanoparticles (20-50 nm diameter) and microparticles (2 μm diameter). Also, the mixed Cu nano-/micro-inks were fabricated, and the synergetic effects between the Cu nano-ink and micro-ink on flash light sintering were assessed. The ratio of nanoparticles to microparticles in Cu ink and the several flash light irradiation conditions (irradiation energy density, pulse number, on-time, and off-time) were optimized to obtain high conductivity of Cu films. In order to precisely monitor the milliseconds-long flash light sintering process, in situ monitoring of electrical resistance and temperature changes of Cu films was conducted during the flash light irradiation using a real-time Wheatstone bridge electrical circuit, thermocouple-based circuit, and a high-rate data acquisition system. Also, several microscopic and spectroscopic characterization techniques such as scanning electron microscopy, x-ray diffraction, x-ray photoelectron spectroscopy, and Fourier transform infrared spectroscopy were used to characterize the flash light sintered Cu nano-/micro-films. In addition, the sheet resistance of Cu film was measured using a four-point probe method. This work revealed that the optimal ratio of nanoparticles to microparticles is 50:50 wt%, and the optimally fabricated and flash light sintered Cu nano-/micro-ink films have the lowest resistivity (80 μΩ cm) among nano-ink, micro-ink, or nano-micro mixed films.

  5. Extraction of protein from high-temperature peanut meal using combination process with steam flash-explosion,alkaline-extraction and acid-precipitation%蒸汽闪爆结合碱溶酸沉法提取高温花生粕中的蛋白质

    Institute of Scientific and Technical Information of China (English)

    章玉清; 杨瑞金; 张文斌; 华霄; 赵伟

    2013-01-01

    以高温花生粕为研究对象,研究了蒸汽闪爆结合碱溶酸沉法提取花生蛋白质的工艺及其产品的功能性质.通过单因素实验和正交实验确定优化的工艺条件为:高温花生粕首先用0.3%的稀硫酸在60℃条件下搅拌浸泡2h;用清水洗去表面稀酸后沥干再进行蒸汽闪爆处理,条件为:爆破压力1.6MPa、维压时间5min;最后采用碱溶酸沉法提取蛋白质,条件为:温度60℃、pH9.5、料水比1∶12(g/mL)、浸提时间为2h.在此工艺条件下,高温花生粕中蛋白质的提取率达到52.6%,比传统碱溶酸沉工艺提高了10.8%,且所得蛋白质产品的持水性、乳化性、起泡性和起泡稳定性有了显著提高,分别增强了67.1%、141.0%、131.3%和107.4%.蒸汽闪爆技术结合碱溶酸沉法适用于从高温花生粕中提取蛋白质,不仅可以提高蛋白质的提取率,而且能够改善产品的功能性质.%A combined process with steam flash-explosion,alkaline-extraction and acid-precipitation was used to extract protein from high-temperature peanut meal.Through single factor and orthogonal test,the optimum conditions were figured out.Firstly,the high-temperature peanut meal was soaked in 0.3% sulfuric acid solution at 60℃ for 2h,then drained it and washed with water to remove the acid solution remained in the surface of the meal.The pretreated meal was treated with steam flash-explosion at 1.6MPa for 5min.The protein in the steam flash-exploded meal was extracted by alkaline-extraction and acid-precipitation process.The optimal condition for alkaline-extraction was solid to water ratio:1∶12(g/mL),pH9.5,60℃ and 2h.Under these conditions,the protein extraction rate reached 52.6%,which was 10.8% higher than conventional alkaline extraction and acid-precipitation process.The water holding capacity,emulsifying activity index,foaming capacity and foaming stability of the protein extracted using this combined process were significantly

  6. Anode characterisation and gas diffusion behaviour in aluminium smelting

    Science.gov (United States)

    Putri, Epma; Brooks, Geoffrey; Snook, Graeme; Eick, Ingo

    2017-01-01

    Over the past century, significant research on different aspects of the Hall-Héroult process has been conducted to increase energy efficiency. Bubble generation at the anode reaction and its contribution to the overall voltage drop in aluminium production holds significant potential for energy saving, yet the details of the gas transport mechanism for bubble nucleation behaviour are not completely understood. The multi-step electrochemical reaction releases predominantly CO2 gas along with CO gas, which is a reduction product formed by reaction of CO2 with the anode carbon. Complicating the reaction is the multiple paths by which the gas can diffuse (either through the porous anode or the electrolyte bath). There has been no detailed investigation of the correlation between gas diffusion as a function of anode and bath properties. In the present study, the porosity measurement techniques in the anode will be used to understand the relation of gas diffusion and anode properties. A porosimetric study was conducted for two different anode samples using mercury intrusion porosimetry (MIP) and hydrostatic method. The MIP method provides important anode properties information such as density, percent porosity, pore size distribution, permeability, and tortuosity factor which affect gas diffusion and anode performance. The Knudsen number obtained from MIP data shows both Knudsen diffusion and molecular diffusion need to be considered when predicting the effective diffusion.

  7. In Situ Flash Pyrolysis of Straw

    DEFF Research Database (Denmark)

    Bech, Niels

    In-Situ Flash Pyrolysis of Straw Ph.D. dissertation by Niels Bech Submitted: April 2007. Supervisors: Professor Kim Dam-Johansen, Associate Professor Peter Arendt Jensen Erfaringerne med forbrænding af halm opnået gennem et årti har vist, at en proces der kan koncentrere energien på marken, fjerne...

  8. Flash-Aware Page Replacement Algorithm

    Directory of Open Access Journals (Sweden)

    Guangxia Xu

    2014-01-01

    Full Text Available Due to the limited main memory resource of consumer electronics equipped with NAND flash memory as storage device, an efficient page replacement algorithm called FAPRA is proposed for NAND flash memory in the light of its inherent characteristics. FAPRA introduces an efficient victim page selection scheme taking into account the benefit-to-cost ratio for evicting each victim page candidate and the combined recency and frequency value, as well as the erase count of the block to which each page belongs. Since the dirty victim page often contains clean data that exist in both the main memory and the NAND flash memory based storage device, FAPRA only writes the dirty data within the victim page back to the NAND flash memory based storage device in order to reduce the redundant write operations. We conduct a series of trace-driven simulations and experimental results show that our proposed FAPRA algorithm outperforms the state-of-the-art algorithms in terms of page hit ratio, the number of write operations, runtime, and the degree of wear leveling.

  9. RELATIONSHIP BETWEEN FLASH POINTS OF SOME BINARY ...

    African Journals Online (AJOL)

    B. S. Chandravanshi

    and BS-150 in the formulation of engine oils, the recent mineral oils were chosen for study. On the other .... blend. Upon analysis of the data due to Figure 1 (b) it can be shown that the flash point of every. SN-150: .... complex compositions.

  10. Successional change in the Lake Superior fish community: population trends in ciscoes, rainbow smelt, and lake trout, 1958-2008

    Science.gov (United States)

    Gorman, Owen T.

    2012-01-01

    The Lake Superior fish community underwent massive changes in the second half of the 20th century. Those changes are largely reflected in changes in abundance of the adults of principal prey species, the ciscoes (Coregonus spp.), the invasive rainbow smelt (Osmerus mordax), and the principal predator, lake trout (Salvelinus namaycush). To better understand changes in species abundances, a comprehensive series of gillnet and bottom trawl data collected from 1958 to 2008 were examined. In the late 1950s/early 1960s, smelt abundance was at its maximum, wild lake trout was at its minimum, and an abundance of hatchery lake trout was increasing rapidly. The bloater (Coregonus hoyi) was the prevalent cisco in the lake; abundance was more than 300% greater than the next most abundant cisco, shortjaw cisco (C. zenithicus), followed by kiyi (C. kiyi) and lake cisco (C. artedi). By the mid-1960s, abundance of hatchery lake trout was nearing maximum, smelt abundance was beginning to decline, and abundances of all ciscoes declined, but especially that of shortjaw cisco and kiyi. By the late 1970s, recovery of wild lake trout stocks was well underway and abundances of hatchery lake trout and smelt were declining and the ciscoes were reaching their nadir. During 1980–1990, the fish community underwent a dramatic shift in organization and structure. The rapid increase in abundance of wild lake trout, concurrent with a rapid decline in hatchery lake trout, signaled the impending recovery. Rainbow smelt abundance dropped precipitously and within four years, lake cisco and bloater populations rebounded on the heels of a series of strong recruitment events. Kiyi populations showed signs of recovery by 1989, and shortjaw by 2000, though well below historic maximum abundances. High abundance of adult smelt prior to 1980 appears to be the only factor linked to recruitment failure in the ciscoes. Life history traits of the cisco species were examined to better understand their different

  11. Comparative analysis of the initial stage in two artificially-triggered lightning flashes

    Science.gov (United States)

    Yang, J.; Qie, X.; Zhang, Q.; Zhao, Y.; Feng, G.; Zhang, T.; Zhang, G.

    2009-02-01

    The initial discharge stages of two flashes during the Shandong Artificially Triggering Lightning Experiment (SHATLE) are analyzed based on the synchronous data of the current and close electromagnetic field. For a lightning flash, named 0503, the wire was connected, not electrically, but via a 5 m length of nylon, with the lightning rod; while for another, named 0602, the wire was connected with the rod directly. Results show that the discharge processes of the initial stage (IS) in flash 0503 are quite different from that of the usual classical-triggered flash 0602 and altitude-triggered flashes. A large pulse with a current of about 720 A resulted from the breakdown of the 5 m air gap during flash 0503, and the corresponding electric field at 60 m from the lightning rod was 0.38 kV/m. The upward positive leaders (UPLs) propagated continuously from the tip of the rocket after this breakdown. The geometric mean (GM) of the UPL peak current was 23.0 A. Vaporization of the wire occurred during the initial continuous current (ICC) stage and the largest current pulse was about 400 A. Compared with triggered flash 0503, the discharge processes of IS in flash 0602 were simple, only two large pulses similar to each other occurred before dart leader/return stroke sequences. The peak current of the first pulse was 2.1 kA and its corresponding electric field and magnetic field at a distance of 60 m from the lightning rod were 0.98 kV/m and 7.03 μT, respectively. During the second pulse, the wire disintegrated. The current decreased to the background level at the moment of the wire disintegration. The current of the second pulse in triggered flash 0602 was 2.8 kA, and the corresponding electric field and magnetic field at 60 m from the lightning rod were 1.22 kV/m and 9.01 μT, respectively.

  12. Ecotoxicological damage from zinc smelting at Palmerton, Pennsylvania

    Science.gov (United States)

    Beyer, W. Nelson; Storm, Gerald L.; Hoffman, David J.; Rattner, Barnett A.; Burton, G. Allen; Cairns, John

    1995-01-01

    The two zinc smelters at Palmerton, PA emitted huge amounts of contaminants ( 260,000 t of Zn, 3,300 t of Cd, 6,800 t of Pb) to the air and severely damaged the forest on Blue Mountain. The high Zn concentrations in soil killed tree seedlings by inhibiting root elongation. The result was a forest with too few young trees. When natural stresses such as fire challenged the forest, the forest failed to regenerate, and the exposed soil eroded down the steep slopes. Tree species that could sprout were favored over those that developed from seeds. As a result of high zinc concentrations, the lichen and moss communities were depauperate for at least 20 km along Blue Mountain. The denuded areas are in the process of being reclaimed with the addition of a mixture of fly ash and sewage sludge, which is seeded with grasses tolerant to the harsh conditions. In preliminary experiments, the fly ash and sewage sludge mixture was stable, despite the steepness of the slopes of the reclaimed sites on Blue Mountain. Zinc emissions reduced the decomposition rate of plant material on Blue Mountain. The partially decomposed litter, in particular, accumulated on the surface of the mineral soil. The populations of both microorganisms and arthropods were greatly reduced in soils near the smelters. Samples of litter collected from sites spanning 30 km were toxic to woodlice, and Zn was shown to be the toxic factor. A white-tailed deer examined had a very high renal Zn concentration and an articular lesion in one of its hind legs that closely resembled the lesions reported in Zn-poisoned horses. Zinc concentrations were regulated in wildlife tissues and were not reliable indicators of exposure, except in extreme cases. Two songbirds, a shrew, and several rabbits contained Pb concentrations that were suggested to be toxic. Shrews and ground-feeding songbirds accumulated relatively high concentrations of Pb. Exposure to Pb seemed to be related to the amount of soil that an animal ingests. Some

  13. Anomalous behavior of the steel alloying elements in the genetic structure of the solid metal at its smelting in electric furnaces

    Directory of Open Access Journals (Sweden)

    Олександр Михайлович Скребцов

    2016-07-01

    Full Text Available Melting process in an electric arc furnace and transformations taking place in solidified metals are not thoroughly understood yet. This article is devoted to these phenomena in liquid and solid metal and therefore is relevant at the moment. The authors sampled molten metal during all periods of mild steel smelting in an electric arc furnace beginning from melting the charge up to metal outlet out of the furnace into the ladle. Samples were analyzed for chemical elements content, and the microstructure of solidified samples (the ratio of ferrite and pearlite. It has been found that elements expanding γ – phase domain of existence (Mn, Ni during oxidation act similarly at deoxidation, but much weaker. This fact is interesting for science, it is advisable that these phenomena should be checked for the metal melted in other melting units – induction and crucible furnaces

  14. Initial electric field changes of lightning flashes in two thunderstorms

    Science.gov (United States)

    Chapman, Ryan; Marshall, Thomas; Karunarathne, Sumedhe; Stolzenburg, Maribeth

    2017-04-01

    The beginning of all 75 lightning flashes in two small thunderstorms was investigated using an array of electric field change (E-change) meters and an array of VHF sensors with the goal of determining if an initial E-change (IEC) preceded the initial breakdown (IB) pulses in each flash. IECs were found at the beginning of all 62 flashes in Storm 1 and all 13 flashes in Storm 2. Hence, it is concluded that an IEC is a fundamental part of most or all lightning initiations and that an IEC is needed prior to the first IB pulse in a flash. IEC durations averaged 0.23 ms for cloud-to-ground (CG) flashes (range 0.08-0.54 ms) and averaged 2.7 ms for normal intracloud (IC) flashes (range 0.04-9.8 ms). IEC point dipole moments averaged 26 C m for CG flashes (range 4-86 C m) and averaged -140 C m for normal IC flashes (range -8 to -650 C m). IEC current moments averaged 120 kA m for CG flashes (range 41-410 kA m) and averaged -91 kA m for normal IC flashes (range -2 to -630 kA m). E-change data support the suggestion that weak narrow bipolar event type events initiate some lightning flashes, but 41 of the 75 flashes had no detectable initiating pulse > 0.04 V m-1 range normalized to 100 km. Two flashes had two IECs; the second IEC of each flash initiated a new lightning channel that propagated in a new direction and at a higher altitude than the original development after the first IEC.

  15. The weight of flash chromatography: A tool to predict its mass intensity from thin-layer chromatography

    OpenAIRE

    Freddy Pessel; Jacques Augé; Isabelle Billault; Marie-Christine Scherrmann

    2016-01-01

    Purification by flash chromatography strongly impacts the greenness of a process. Unfortunately, due to the lack of the relevant literature data, very often this impact cannot be assessed thus preventing the comparison of the environmental factors affecting the syntheses. We developed a simple mathematical approach to evaluate the minimum mass intensity of flash chromatography from the retention factor values determined by thin-layer chromatography.

  16. The weight of flash chromatography: A tool to predict its mass intensity from thin-layer chromatography

    Directory of Open Access Journals (Sweden)

    Freddy Pessel

    2016-11-01

    Full Text Available Purification by flash chromatography strongly impacts the greenness of a process. Unfortunately, due to the lack of the relevant literature data, very often this impact cannot be assessed thus preventing the comparison of the environmental factors affecting the syntheses. We developed a simple mathematical approach to evaluate the minimum mass intensity of flash chromatography from the retention factor values determined by thin-layer chromatography.

  17. Synthesis and characterization of tenorite (CuO nanoparticles from smelting furnace dust(SFD

    Directory of Open Access Journals (Sweden)

    Darezereshki E.

    2013-01-01

    Full Text Available Tenorite (CuO nanoparticles were prepared from a dilute CuSO4 solution. The solution was obtained by leaching (pH=1.5 of smelting furnace dust of Sarcheshmeh Copper Complex, Iran. The recovery of copper from the acidic sulphate solution was carried out by solvent extraction using Lix 984-N. Tenorite nanoparticles were synthesized by direct thermal decomposition of Langite [Cu4(OH6SO4(H2O2] as a precursor which was calcinated in air for 2 h at 750°C. The Samples were characterized by X-ray diffraction, infrared spectroscopy, scanning electron microscopy, and transmission electron microscopy. The average diameter of the spherical pure CuO nanoparticles and their crystallite size were estimated to be 92 nm and 40nm, respectively. The simplicity of the present method suggests its potential application at industrial scale as a cheap and convenient way to produce pure CuO nanoparticles from dilute CuSO4 solutions obtained from leaching of smelting furnace dust.

  18. Additions and improvements to the high energy density physics capabilities in the FLASH code

    Science.gov (United States)

    Lamb, D. Q.; Flocke, N.; Graziani, C.; Tzeferacos, P.; Weide, K.

    2016-10-01

    FLASH is an open source, finite-volume Eulerian, spatially adaptive radiation magnetohydrodynamics code that has the capabilities to treat a broad range of physical processes. FLASH performs well on a wide range of computer architectures, and has a broad user base. Extensive high energy density physics (HEDP) capabilities have been added to FLASH to make it an open toolset for the academic HEDP community. We summarize these capabilities, emphasizing recent additions and improvements. In particular, we showcase the ability of FLASH to simulate the Faraday Rotation Measure produced by the presence of magnetic fields; and proton radiography, proton self-emission, and Thomson scattering diagnostics with and without the presence of magnetic fields. We also describe several collaborations with the academic HEDP community in which FLASH simulations were used to design and interpret HEDP experiments. This work was supported in part at the University of Chicago by the DOE NNSA ASC through the Argonne Institute for Computing in Science under field work proposal 57789; and the NSF under Grant PHY-0903997.

  19. Analysis of thermal stresses induced in silicon during xenon arc lamp flash annealing

    Science.gov (United States)

    Bentini, G. G.; Correra, L.

    1983-04-01

    Evaluation of thermal stresses induced on silicon wafers during flash annealing with incoherent light from a xenon lamp has been performed. The thermally induced stresses have been computed taking into account that the slip planes, in silicon crystal, are {111} and the slip directions in the plane are . The computed stresses have been compared with the yield stress of the material, to determine the threshold of damage introduction by the annealing process. For the light flash durations shorter than 500 μsec, a preheating of the sample is necessary to obtain a good annealing of a 1000 Å implanted layer without defects introduction. A relationship among flash duration, preheating temperature and flash energy density has been established allowing the identification of the best annealing conditions. The computed results have been compared with experimental annealing data obtained on silicon, phosphorus implanted at 10 keV, 1.5×1015 at/cm2 and irradiated with an original flash annealing system set up in our laboratory.

  20. Largest domestic tungsten and molybdenum deep processing project finding its home in Luan-chuan

    Institute of Scientific and Technical Information of China (English)

    2007-01-01

    <正>Recently, a tungsten and molybdenum deep processing project was formally executed with a joint investment of 300 million yuan from Luanchuan Molybdenum Mining & Smelting Co., Ltd, Beijing Tian-Long Tungsten & Mo-

  1. Two-step flash light sintering of copper nanoparticle ink to remove substrate warping

    Energy Technology Data Exchange (ETDEWEB)

    Ryu, Chung-Hyeon; Joo, Sung-Jun [Department of Mechanical Convergence Engineering, Hanyang University, Haengdang-dong, Seongdong-gu, Seoul 133-791 (Korea, Republic of); Kim, Hak-Sung, E-mail: kima@hanyang.ac.kr [Department of Mechanical Convergence Engineering, Hanyang University, Haengdang-dong, Seongdong-gu, Seoul 133-791 (Korea, Republic of); Institute of Nano Science and Technology, Hanyang University, Seoul, 133-791 (Korea, Republic of)

    2016-10-30

    Highlights: • We performed the two-step flash light sintering for copper nanoparticle ink to remove substrate warping. • 12 J/cm{sup 2} of preheating and 7 J/cm{sup 2} of main sintering energies were determined as optimum conditions to sinter the copper nanoparticle ink. • The resistivity of two-step sintered copper nanoparticle ink was 3.81 μΩ cm with 5B adhesion level, 2.3 times greater than that of bulk copper. • The two-step sintered case showed a high conductivity without any substrate warping. - Abstract: A two-step flash light sintering process was devised to reduce the warping of polymer substrates during the sintering of copper nanoparticle ink. To determine the optimum sintering conditions of the copper nanoparticle ink, the flash light irradiation conditions (pulse power, pulse number, on-time, and off-time) were varied and optimized. In order to monitor the flash light sintering process, in situ resistance and temperature monitoring of copper nanoink were conducted during the flash light sintering process. Also, a transient heat transfer analysis was performed by using the finite-element program ABAQUS to predict the temperature changes of copper nanoink and polymer substrate. The microstructures of the sintered copper nanoink films were analyzed by scanning electron microscopy. Additionally, an X-ray diffraction and Fourier transform infrared spectroscopy were used to characterize the crystal phase change of the sintered copper nanoparticles. The resulting two-step flash light sintered copper nanoink films exhibited a low resistivity (3.81 μΩ cm, 2.3 times of that of bulk copper) and 5B level of adhesion strength without warping of the polymer substrate.

  2. Integrated flash flood vulnerability assessment: Insights from East Attica, Greece

    Science.gov (United States)

    Karagiorgos, Konstantinos; Thaler, Thomas; Heiser, Micha; Hübl, Johannes; Fuchs, Sven

    2016-10-01

    In the framework of flood risk assessment, vulnerability is a key concept to assess the susceptibility of elements at risk. Besides the increasing amount of studies on flash floods available, in-depth information on vulnerability in Mediterranean countries was missing so far. Moreover, current approaches in vulnerability research are driven by a divide between social scientists who tend to view vulnerability as representing a set of socio-economic factors, and natural scientists who view vulnerability in terms of the degree of loss to an element at risk. Further, vulnerability studies in response to flash flood processes are rarely answered in the literature. In order to close this gap, this paper implemented an integrated vulnerability approach focusing on residential buildings exposed to flash floods in Greece. In general, both physical and social vulnerability was comparable low, which is interpreted as a result from (a) specific building regulations in Greece as well as general design principles leading to less structural susceptibility of elements at risk exposed, and (b) relatively low economic losses leading to less social vulnerability of citizens exposed. The population show high risk awareness and coping capacity to response to natural hazards event and in the same time the impact of the events are quite low, because of the already high use of local protection measures. The low vulnerability score for East Attica can be attributed especially to the low physical vulnerability and the moderate socio-economic well-being of the area. The consequence is to focus risk management strategies mainly in the reduction of the social vulnerability. By analysing both physical and social vulnerability an attempt was made to bridge the gap between scholars from sciences and humanities, and to integrate the results of the analysis into the broader vulnerability context.

  3. The relativistic feedback discharge model of terrestrial gamma ray flashes

    Science.gov (United States)

    Dwyer, Joseph R.

    2012-02-01

    As thunderclouds charge, the large-scale fields may approach the relativistic feedback threshold, above which the production of relativistic runaway electron avalanches becomes self-sustaining through the generation of backward propagating runaway positrons and backscattered X-rays. Positive intracloud (IC) lightning may force the large-scale electric fields inside thunderclouds above the relativistic feedback threshold, causing the number of runaway electrons, and the resulting X-ray and gamma ray emission, to grow exponentially, producing very large fluxes of energetic radiation. As the flux of runaway electrons increases, ionization eventually causes the electric field to discharge, bringing the field below the relativistic feedback threshold again and reducing the flux of runaway electrons. These processes are investigated with a new model that includes the production, propagation, diffusion, and avalanche multiplication of runaway electrons; the production and propagation of X-rays and gamma rays; and the production, propagation, and annihilation of runaway positrons. In this model, referred to as the relativistic feedback discharge model, the large-scale electric fields are calculated self-consistently from the charge motion of the drifting low-energy electrons and ions, produced from the ionization of air by the runaway electrons, including two- and three-body attachment and recombination. Simulation results show that when relativistic feedback is considered, bright gamma ray flashes are a natural consequence of upward +IC lightning propagating in large-scale thundercloud fields. Furthermore, these flashes have the same time structures, including both single and multiple pulses, intensities, angular distributions, current moments, and energy spectra as terrestrial gamma ray flashes, and produce large current moments that should be observable in radio waves.

  4. Digital post-calibration of a 5-bit 1.25 GS/s flash ADC

    Institute of Scientific and Technical Information of China (English)

    杨阳; 赵显利; 仲顺安; 李国峰

    2012-01-01

    We report a high-speed flash analog to digital converter (ADC) linearization technique employing the inverse Volterra model and digital post processing.First,a 1.25 GS/s 5-bit flash ADC is designed using a 0.18μm CMOS,and the signal is quantized by a distributed track-and-hold circuit.Second,based on the Volterra series,a proposed digital post-calibration model is introduced.Then,the model is applied to estimate and compensate the nonlinearity of the high-speed flash ADC.Simulation results indicate that the distortion is reduced effectively.Specifically,the ADC achieves gains of 4.83 effective bits for a 117.1 MHz frequency input and 4.74 effective bits for a Nyquist input at 1.25 GS/s.

  5. A NEW APPROACH TO DESIGN LOW POWER CMOS FLASH A/D CONVERTER

    Directory of Open Access Journals (Sweden)

    Sudakar S. Chauhan

    2011-06-01

    Full Text Available In the present paper, a 4-bit flash analog to digital converter for low power SoC application is presented. CMOS inverter has been used as a comparator and by adjusting the ratio of channel width and length, the switching threshold of the CMOS inverter is varied to detect the input analog signal. The simulation results show that this proposed 4-bit flash ADC consumes about 12.4 mW at 200M sample/s with 3.3V supply voltage in TSMC 0.35 μm process. Compared with the traditional flash ADC, this proposed method can reduce about 78% in power consumption.

  6. Matter Flashed at Ultra Speed

    Science.gov (United States)

    2007-06-01

    "REM observations of GRB060418 and GRB060607A: the onset of the afterglow and the initial fireball Lorentz factor determination", by E. Molinari, S. D. Vergani, D. Malesani, S. Covino, et al. The paper is available at http://dx.doi.org/10.1051/0004-6361:20077388 (A&A, 469, L13-L16, 2007). The REM team is formed by G. Chincarini, E. Molinari, F.M. Zerbi, L.A. Antonelli, S. Covino, P. Conconi, L. Nicastro, E. Palazzi, M. Stefanon, V. Testa, G. Tosti, F. Vitali, A. Monfardini, F. D'Alessio, P. D'Avanzo, D. Fugazza, G. Malaspina, S. Piranomonte, S.D. Vergani, P.A. Ward, S. Campana, P. Goldoni, D. Guetta, D. Malesani, N. Masetti, E.J.A. Meurs, L. Norci, E. Pian, A. Fernandez-Soto, L. Stella, G. Tagliaferri, G. Ihle, L. Gonzalez, A. Pizarro, P. Sinclair, and J. Valenzuela. Notes Gamma-ray bursts (GRBs) are short flashes of energetic gamma-rays lasting from less than a second to several minutes. They release a tremendous quantity of energy in this short time making them the most powerful events since the Big Bang. They come in two different flavours, long and short ones. Over the past few years, international efforts have convincingly shown that long gamma-ray bursts are linked with the ultimate explosion of massive stars (hypernovae; see e.g. ESO PR 16/03) while the short ones most likely originate from the violent collision of neutron stars and/or black holes (see e.g. ESO PR 26/05 and 32/05). Irrespective of the original source of the GRB energy, the injection of so much energy into a confined volume will cause a fireball to form. Gamma-ray photons have nearly a million times more energy than the 'visual' photons the eye can see. Strictly speaking, the Lorentz factor is the ratio between the total and rest-mass energy of the fireball. REM (Rapid Eye Mount) is a small (60 cm mirror diameter) rapid reaction automatic telescope dedicated to monitor the prompt afterglow of Gamma Ray Burst events. It is located at the ESO La Silla Observatory in Chile. For more information, see

  7. Next High Performance and Low Power Flash Memory Package Structure

    Institute of Scientific and Technical Information of China (English)

    Jung-Hoon Lee

    2007-01-01

    In general, SAND flash memory has advantages in low power consumption, storage capacity, and fast erase/write performance in contrast to NOR flash. But, main drawback of the SAND flash memory is the slow access time for random read operations. Therefore, we proposed the new SAND flash memory package for overcoming this major drawback. We present a high performance and low power SAND flash memory system with a dual cache memory. The proposed SAND flash package consists of two parts, i.e., an SAND flash memory module, and a dual cache module. The new SAND flash memory system can achieve dramatically higher performance and lower power consumption compared with any conventional NAND-type flash memory module. Our results show that the proposed system can reduce about 78% of write operations into the flash memory cell and about 70% of read operations from the flash memory cell by using only additional 3KB cache space. This value represents high potential to achieve low power consumption and high performance gain.

  8. Flash Learning Games Wow Students and Instructors: Moving Toward An Academic Gaming Portal

    Directory of Open Access Journals (Sweden)

    Dan H Lim

    2003-02-01

    Full Text Available This paper describes and discusses the rationale, background, design, and implementation of Flash learning games. The paper explains why Macromedia Flash has been selected as the authoring tool in the development of highly interactive learning games for online learning. The background evolutionary process of developing the learning games points out why it has been a daunting task to create compelling learning games that impact learning. Designing learning game objects that allow other educators to customize game content is the core of this paper. The author envisions this academic gaming project will evolve into an academic gaming portal, developed in conjunction with other major institutional partners.

  9. NUMERICAL SIMULATION OF TEMPERATURE FIELD ON FLASH BUTT WELDING FOR HIGH MANGANESE STEELS

    Institute of Scientific and Technical Information of China (English)

    B.D. Yu; W.D. Song; F.C. Zhang

    2005-01-01

    An axial symmetry finite element model coupled with electricity-thermal effect was developed to study the temperature field distribution in process of the flash butt welding (FBW) of frog highmanganese steel. The influence of temperature dependent material properties and the contact resistance were taken into account in FEMsimulation. Meanwhile, the lost materials due to splutter was resolved by using birth and death element. The result of analyzing data shows that the model in the FBW flashing is reasonable and feasible, and can exactly simulate the temperature field distribution. The modeling provides reference for analysis of welding technologies on the temperature field of high-manganese steel in FBW.

  10. Creating Flash advertising from concept to tracking-microsites, video ads and more

    CERN Document Server

    Fincanon, Jason

    2007-01-01

    Create awe-inspiring, mind-blowing Flash ads and microsites that engage consumers and demonstrate their worth to clients. The Hands-On Guide to Creating Flash Advertising delivers the nuts and bolts of the development process from initial design conception to ad completion. You'll learn the best practices for:* Mastering the myriad of ad specs, deadlines, quality and version control issues* Creating ads that balance campaign goals with design constraints* Preparing and building ads with team and QC standards* Using forms and data in ads without file bloat* File optimization techniques for swf

  11. Experimental Research on Flash Boiling Spray of Dimethyl Ether

    Institute of Scientific and Technical Information of China (English)

    Peng Zhang

    2014-01-01

    The high-speed digital imaging technique is applied to observe the developing process of flash boiling spray of dimethyl ether at low ambient pressure, and the effects of nozzle opening pressure and nozzle hole diameter on the spray shape, spray tip penetration and spray angle during the injection are investigated. The experimental results show that the time when the vortex ring structure of flash boiling spray forms and its developing process are determined by the combined action of the bubble growth and breakup in the spray and the air drag on the leading end of spray;with the enhancement of nozzle opening pressure, the spray tip penetration increases and the spray angle decreases. The influence of nozzle hole diameter on the spray tip penetration is relatively complicated, the spray tip penetration is longer with a smaller nozzle hole diameter at the early stage of injection, while the situation is just opposite at the later stage of injection. This paper establishes that the variation of spray angle is consistent with that of nozzle hole diameter.

  12. Experimental research on flash boiling spray of dimethyl ether

    Science.gov (United States)

    Zhang, Peng

    2014-12-01

    The high-speed digital imaging technique is applied to observe the developing process of flash boiling spray of dimethyl ether at low ambient pressure, and the effects of nozzle opening pressure and nozzle hole diameter on the spray shape, spray tip penetration and spray angle during the injection are investigated. The experimental results show that the time when the vortex ring structure of flash boiling spray forms and its developing process are determined by the combined action of the bubble growth and breakup in the spray and the air drag on the leading end of spray; with the enhancement of nozzle opening pressure, the spray tip penetration increases and the spray angle decreases. The influence of nozzle hole diameter on the spray tip penetration is relatively complicated, the spray tip penetration is longer with a smaller nozzle hole diameter at the early stage of injection, while the situation is just opposite at the later stage of injection. This paper establishes that the variation of spray angle is consistent with that of nozzle hole diameter.

  13. Characterization and modeling of fast programming bits in flash EEPROM

    Science.gov (United States)

    Nkansah, F.; Hatalis, M.; Olasupo, K.

    2000-11-01

    The effects of flash EEPROM floating gate (FG) morphology on the generation and density of fast programming bits in a 2Mbit flash EEPROM array has been characterized. These fast programming bits exhibit identical subthreshold characteristics similar to that of a normal bit after UV erase, thus establishing that the initial charge stored on the FG of both fast and normal bit is the same. Experimental results clearly indicates that the fast programming phenomena result from an interaction of the programming process with the FG polysilicon microstructure. An in-depth experimentation previously reported, reveals that the FG poly deposition and doping processes are crucial for controlling the desired Fowler-Nordheim tunneling. A correlation is established between the fast bit density observed in the memory arrays, the FG polysilicon grain size and tunneling field enhancement factor μ( Rc). A compact model of the fast programming bit memory threshold voltage as a function of the effective FG polysilicon grain area factor Geff, and tunneling field enhancement factor μ( Rc) has been developed for the first time.

  14. Formation of curcumin nanoparticles by flash nanoprecipitation from emulsions.

    Science.gov (United States)

    Margulis, Katherine; Magdassi, Shlomo; Lee, Han Seung; Macosko, Christopher W

    2014-11-15

    Nanometric particles of a model hydrophobic substance curcumin were prepared by a novel method, namely, flash nanoprecipitation from a coarse oil-in-water emulsion. The method employs turbulent co-mixing of water with curcumin-loaded emulsion using manually-operated confined impingement jets mixer. A clear and stable dispersion of nanoparticles was formed in this process, and could be converted to dry, easily water-dispersible powder by spray drying. The mean size of the particles was about 40 nm by DLS, confirmed by Cryo-TEM. The obtained particles contained 20.4 wt% curcumin, X-ray analysis showed it was amorphous. The significant advantages of the studied process are its feasibility, speed and low cost. It does not require any special high-energy input equipment to reduce the droplet size of the initial emulsion as required by the vast majority of other methods, and relies on rapid turbulent mixing and on flow-induced shear stress formed in the simple, manually-operated mixer. Control experiments clearly indicate that employing emulsion, instead of a plain solution and flash nanoprecipitation instead of a simple antisolvent precipitation are advantageous in terms of particle size and stability.

  15. Guangxi Nanguo Copper’s150,000 t/a Copper Smelting Project was Approval by the MEP

    Institute of Scientific and Technical Information of China (English)

    2013-01-01

    <正>In the middle of August,the environmental impact report for 150,000 t/a copper smelting project of Guangxi Nanguo Copper Industry Co.,Ltd received formal approval from the Ministry of Environmental Protection,signaling that this project’s environmental impact

  16. The “Standardization Conditions for Copper Smelting Industry” will Soon Be Published,Large Copper Manufacturers Will Become Beneficiary

    Institute of Scientific and Technical Information of China (English)

    2014-01-01

    <正>According to Chen Xuesen,Section Chief of the Department of Raw Materials,the Ministry of Industry and Information Technology,the"Standardization Conditions for Copper Smelting Industry"has completed all procedures,but has not been printed and distributed yet,"it will not be printed and distributed this week,and might be printed and

  17. 75 FR 39625 - Elimination of Flash Order Exception From Rule 602 of Regulation NMS

    Science.gov (United States)

    2010-07-09

    ... proposal originally was published in Securities Exchange Act Release No. 60684 (September 18, 2009), 74 FR...), 74 FR 48632 (September 23, 2009) (``Proposing Release''). The Proposing Release contains a detailed... execution in the flash process. \\11\\ See Securities Exchange Act Release No. 61902 (April 14, 2010), 75...

  18. Musicians have enhanced audiovisual multisensory binding: experience-dependent effects in the double-flash illusion.

    Science.gov (United States)

    Bidelman, Gavin M

    2016-10-01

    Musical training is associated with behavioral and neurophysiological enhancements in auditory processing for both musical and nonmusical sounds (e.g., speech). Yet, whether the benefits of musicianship extend beyond enhancements to auditory-specific skills and impact multisensory (e.g., audiovisual) processing has yet to be fully validated. Here, we investigated multisensory integration of auditory and visual information in musicians and nonmusicians using a double-flash illusion, whereby the presentation of multiple auditory stimuli (beeps) concurrent with a single visual object (flash) induces an illusory perception of multiple flashes. We parametrically varied the onset asynchrony between auditory and visual events (leads and lags of ±300 ms) to quantify participants' "temporal window" of integration, i.e., stimuli in which auditory and visual cues were fused into a single percept. Results show that musically trained individuals were both faster and more accurate at processing concurrent audiovisual cues than their nonmusician peers; nonmusicians had a higher susceptibility for responding to audiovisual illusions and perceived double flashes over an extended range of onset asynchronies compared to trained musicians. Moreover, temporal window estimates indicated that musicians' windows (audiovisual binding. Collectively, findings indicate a more refined binding of auditory and visual cues in musically trained individuals. We conclude that experience-dependent plasticity of intensive musical experience extends beyond simple listening skills, improving multimodal processing and the integration of multiple sensory systems in a domain-general manner.

  19. Enlarged temporal integration window in schizophrenia indicated by the double-flash illusion

    NARCIS (Netherlands)

    Haß, Katharina; Sinke, Christopher; Reese, Tanya; Roy, Mandy; Wiswede, Daniel; Dillo, Wolfgang; Oranje, Bob; Szycik, Gregor R.

    2017-01-01

    Introduction: In the present study we were interested in the processing of audio-visual integration in schizophrenia compared to healthy controls. The amount of sound-induced double-flash illusions served as an indicator of audio-visual integration. We expected an altered integration as well as a

  20. Technology for Smelting V-N Micro-alloyed Steel by Blowing Nitrogen%气体增氮法冶炼钒氮微合金钢

    Institute of Scientific and Technical Information of China (English)

    康伟; 康磊; 赵坦; 廖相巍

    2014-01-01

    从理论上分析了钢液增氮的热力学、动力学影响因素,进行了BOF+RH双联吹氮冶炼钒氮钢试验。结果表明,转炉底吹、RH喷吹均能有效增加钢液氮含量。 RH真空度两段式控制既能满足控氢要求又能实现钢液搬出时较高的氮含量。 BOF+RH双联吹氮气工艺可以不加含氮合金冶炼钒氮微合金钢。%The thermodynamic and dynamic influence factors for increasing the content of ni-trogen in molten steel are theoretically analyzed and the experiment for the smelting V-N contain-ing steel by blowing nitrogen into both BOF and RH is carried out. The results show that the con-tent of nitrogen in molten steel can be effectively increased by converter bottom blowing and RH blowing. With its characteristics of the RH blowing the two-stage control technology for RH vacu-um degree can meet the requirement for controlling the content of hydrogen and also the molten steel with relative high content of nitrogen can be available when tapping. V-N micro-alloyed steel can be smelted without adding the nitrogen-containing alloy by using BOF and RH duplex nitro-gen-blowing process.

  1. Research on the Effect of Ammonium Ion Concentration on Nickel Smelting Technology%铵离子浓度对沉镍工艺的影响研究

    Institute of Scientific and Technical Information of China (English)

    杨小山; 魏万林

    2012-01-01

    在红土镍矿湿法浸出过程中,采用氨法沉镁提取镁盐产品后产生的大量工业废水,如直接排放会影响生态环境,一般都会回用做为镍冶炼工业用水.试验表明含铵浓度不超过0.5 g/L时,对沉镍时Ni、Mn沉淀率和耗碱量无影响,反而可以提高含镁废水中的镁含量,有利于含镁废水的氨法沉镁生产工艺.同时解决了镍冶炼过程中含镁母液氨法沉镁后的废水排放问题,达到了生产用水的循环综合利用,有效的节约了水资源,降低了生产成本.%Much quantity of waste water is discharged when magnesium product is produced by ammonia method during nickel is extracted by wet method from laterite nickel ore. The environment will be polluted if the waste water is discharged directly. Waste water is often recycled to be industrial water for nickel smelting. It is showed by experiment that there has no effect on depositing rate of Ni, Mn and the quantity of consumed alkali if the concentration of ammonium is less than 0. 5 g/L. In such a case, the magnesium contented in the waste water is improved and favorable for magnesium production by ammonia depositing method. It can solve the problem of waste water discharging during nickel smelting process because the waste water is recycled to be industrial water after magnesium is deposited by ammonia method. The water resource is saved and the production cost is decreased effectively.

  2. Effect of Calcium Oxide on the Crushing Strength, Reduction, and Smelting Performance of High-Chromium Vanadium–Titanium Magnetite Pellets

    Directory of Open Access Journals (Sweden)

    Gongjin Cheng

    2017-05-01

    Full Text Available The effect of calcium oxide on the crushing strength, reduction, and smelting performance of high-chromium vanadium–titanium magnetite pellets (HCVTMP was studied in this work. The main characterization methods of an electronic universal testing machine (EUTM, X-ray fluorescent (XRF, inductively-coupled plasma-atomic emission spectroscopy (ICP-AES, X-ray diffraction (XRD, and scanning electron microscope-energy disperse spectroscopy (SEM-EDS were employed. The crushing strength was affected by the mineral phases generated during oxidative baking and the subsequently-formed pellet microstructures owing to CaO addition. The reduction and smelting properties of HCVTMP with different CaO additives were measured and characterized with different softening-melting-dripping indices. Although HCVTMP showed the highest crushing strength with CaO addition of ca. 2 wt %, more CaO addition may be needed to achieve high permeability of the furnace burdens and a good separation condition of the slag and melted iron. In the formation process of the slag and melted iron, it can be determined that CaO could have a relationship with the transformation behavior of Cr, V, and Ti to some extent, with respect to the predominant chemical composition analysis of ICP-AES and XRF. With the microscopic examination, the restraining formation of Ti(C,N and the promoting formation of CaTiO3 are in accordance with the improved melting-dripping indices, including the decrease of the maximum external static load and gas permeability, and the increase of the melting-dripping zone and dripping difficulty.

  3. Gun muzzle flash detection using a single photon avalanche diode array in 0.18µm CMOS technology

    Science.gov (United States)

    Savuskan, Vitali; Jakobson, Claudio; Merhav, Tomer; Shoham, Avi; Brouk, Igor; Nemirovsky, Yael

    2015-05-01

    In this study, a CMOS Single Photon Avalanche Diode (SPAD) 2D array is used to record and sample muzzle flash events in the visible spectrum, from representative weapons. SPADs detect the emission peaks of alkali salts, potassium or sodium, with spectral emission lines around 769nm and 589nm, respectively. The alkali salts are included in the gunpowder to suppress secondary flashes ignited during the muzzle flash event. The SPADs possess two crucial properties for muzzle flash imaging: (i) very high photon detection sensitivity, (ii) a unique ability to convert the optical signal to a digital signal at the source pixel, thus practically eliminating readout noise. The sole noise sources are the ones prior to the readout circuitry (optical signal distribution, avalanche initiation distribution and nonphotonic generation). This enables high sampling frequencies in the kilohertz range without significant SNR degradation, in contrast to regular CMOS image sensors. This research will demonstrate the SPAD's ability to accurately sample and reconstruct the temporal behavior of the muzzle flash in the visible wavelength, in the presence of sunlight. The reconstructed signal is clearly distinguishable from background clutter, through exploitation of flash temporal characteristics and signal processing, which will be reported. The frame rate of ~16 KHz was chosen as an optimum between SNR degradation and temporal profile recognition accuracy. In contrast to a single SPAD, the 2D array allows for multiple events to be processed simultaneously. Moreover, a significant field of view is covered, enabling comprehensive surveillance and imaging.

  4. Oral bioaccessibility of inorganic contaminants in waste dusts generated by laterite Ni ore smelting.

    Science.gov (United States)

    Ettler, Vojtěch; Polák, Ladislav; Mihaljevič, Martin; Ratié, Gildas; Garnier, Jérémie; Quantin, Cécile

    2016-09-14

    The laterite Ni ore smelting operations in Niquelândia and Barro Alto (Goiás State, Brazil) have produced large amounts of fine-grained smelting wastes, which have been stockpiled on dumps and in settling ponds. We investigated granulated slag dusts (n = 5) and fly ash samples (n = 4) with a special focus on their leaching behaviour in deionised water and on the in vitro bioaccessibility in a simulated gastric fluid, to assess the potential exposure risk for humans. Bulk chemical analyses indicated that both wastes contained significant amounts of contaminants: up to 2.6 wt% Ni, 7580 mg/kg Cr, and 508 mg/kg Co. In only one fly ash sample, after 24 h of leaching in deionised water, the concentrations of leached Ni exceeded the limit for hazardous waste according to EU legislation, whereas the other dusts were classified as inert wastes. Bioaccessible fractions (BAF) of the major contaminants (Ni, Co, and Cr) were quite low for the slag dusts and accounted for less than 2 % of total concentrations. In contrast, BAF values were significantly higher for fly ash materials, which reached 13 % for Ni and 19 % for Co. Daily intakes via oral exposure, calculated for an adult (70 kg, dust ingestion rate of 50 mg/day), exceeded neither the tolerable daily intake (TDI) nor the background exposure limits for all of the studied contaminants. Only if a higher ingestion rate is assumed (e.g. 100 mg dust per day for workers in the smelter), the TDI limit for Ni recently defined by European Food Safety Authority (196 µg/day) was exceeded (324 µg/day) for one fly ash sample. Our data indicate that there is only a limited risk to human health related to the ingestion of dust materials generated by laterite Ni ore smelting operations if appropriate safety measures are adopted at the waste disposal sites and within the smelter facility.

  5. Using GHz Flash ADCs at STACEE

    Science.gov (United States)

    Zweerink, Jeffrey

    2002-04-01

    The Solar Tower Atmospheric Cherenkov Effect Experiment (STACEE) detects 50-500 GeV gamma rays by sampling the Cherenkov light wavefront generated as the gamma rays interact with the atmosphere. Using steerable heliostat mirrors and stationary secondary optics at the National Solar Thermal Test Facility in New Mexico, the Cherenkov light is recorded using fast electronics with good timing. One significant improvement of the full 64 channel STACEE detector over earlier prototypes is the addition of GHz flash ADCs on each channel. We are developing analysis techniques to extract timing and other pulse information from the flash ADCs in order to 1.) discriminate against the abundant cosmic ray background, and 2.) understand how well the shower direction and energy can be reconstructed. We describe the techniques and present results from data taken during the 2001-2002 observing season.

  6. Electrical Safety and Arc Flash Protections

    Energy Technology Data Exchange (ETDEWEB)

    R. Camp

    2008-03-04

    Over the past four years, the Electrical Safety Program at PPPL has evolved in addressing changing regulatory requirements and lessons learned from accident events, particularly in regards to arc flash hazards and implementing NFPA 70E requirements. This presentation will discuss PPPL's approaches to the areas of electrical hazards evaluation, both shock and arc flash; engineered solutions for hazards mitigation such as remote racking of medium voltage breakers, operational changes for hazards avoidance, targeted personnel training and hazard appropriate personal protective equipment. Practical solutions for nominal voltage identification and zero voltage checks for lockout/tagout will also be covered. Finally, we will review the value of a comprehensive electrical drawing program, employee attitudes expressed as a personal safety work ethic, integrated safety management, and sustained management support for continuous safety improvement.

  7. Direct flash steam geothermal power plant assessment

    Science.gov (United States)

    Alt, T. E.

    1982-01-01

    The objective was to analyze the capacity and availability factors of an operating direct flash geothermal power plant. System and component specifications, operating procedures, maintenance history, malfunctions, and outage rate are discussed. The plant studied was the 75 MW(e) geothermal power plant at Cerro Prieto, Mexico, for the years 1973 to 1979. To describe and assess the plant, the project staff reviewed documents, visited the plant, and met with staff of the operating utility. The high reliability and availability of the plant was documented and actions responsible for the good performance were identified and reported. The results are useful as guidance to US utilities considering use of hot water geothermal resources for power generation through a direct flash conversion cycle.

  8. 450mm wafer patterning with jet and flash imprint lithography

    Science.gov (United States)

    Thompson, Ecron; Hellebrekers, Paul; Hofemann, Paul; LaBrake, Dwayne L.; Resnick, Douglas J.; Sreenivasan, S. V.

    2013-09-01

    The next step in the evolution of wafer size is 450mm. Any transition in sizing is an enormous task that must account for fabrication space, environmental health and safety concerns, wafer standards, metrology capability, individual process module development and device integration. For 450mm, an aggressive goal of 2018 has been set, with pilot line operation as early as 2016. To address these goals, consortiums have been formed to establish the infrastructure necessary to the transition, with a focus on the development of both process and metrology tools. Central to any process module development, which includes deposition, etch and chemical mechanical polishing is the lithography tool. In order to address the need for early learning and advance process module development, Molecular Imprints Inc. has provided the industry with the first advanced lithography platform, the Imprio® 450, capable of patterning a full 450mm wafer. The Imprio 450 was accepted by Intel at the end of 2012 and is now being used to support the 450mm wafer process development demands as part of a multi-year wafer services contract to facilitate the semiconductor industry's transition to lower cost 450mm wafer production. The Imprio 450 uses a Jet and Flash Imprint Lithography (J-FILTM) process that employs drop dispensing of UV curable resists to assist high resolution patterning for subsequent dry etch pattern transfer. The technology is actively being used to develop solutions for markets including NAND Flash memory, patterned media for hard disk drives and displays. This paper reviews the recent performance of the J-FIL technology (including overlay, throughput and defectivity), mask development improvements provided by Dai Nippon Printing, and the application of the technology to a 450mm lithography platform.

  9. Characterization, distribution, and risk assessment of heavy metals in agricultural soil and products around mining and smelting areas of Hezhang, China.

    Science.gov (United States)

    Briki, Meryem; Ji, Hongbing; Li, Cai; Ding, Huaijian; Gao, Yang

    2015-12-01

    Mining and smelting have been releasing huge amount of toxic substances into the environment. In the present study, agricultural soil and different agricultural products (potato, Chinese cabbage, garlic bolt, corn) were analyzed to examine the source, spatial distribution, and risk of 12 elements (As, Be, Bi, Cd, Co, Cr, Cu, Hg, Ni, Pb, Sb, and Zn) in agricultural soil near mine fields, smelting fields, and mountain field around Hezhang County, west of Guizhou Province, China. Multivariate statistical analysis indicated that in mining area, As, Bi, Cd, Cu, Hg, Pb, Sb, and Zn were generated from anthropogenic sources; in smelting area, As, Be, Cd, Co, Cu, Pb, Sb, and Zn were derived from anthropogenic sources through zinc smelting ceased in 2004. The enrichment factors (EFs) and ecological risk index (RI) of soil in mining area are the most harmful, showing extremely high enrichment and very high ecological risk of As, Bi, Cd, Cu, Hg, Pb, Sb, and Zn. Zinc is the most significant enriched in the smelting area; however, mountain area has a moderate enrichment and ecological risk and do not present any ecological risk. According to spatial distribution, the concentrations depend on the nearby mining and smelting activities. Transfer factors (TFs) in the smelting area and mountain are high, implying a threat for human consumption. Therefore, further studies should be carried out taking into account the harm of those heavy metals and potential negative health effects from the consumption of agricultural products in these circumstances.

  10. How to give a science flash talk

    DEFF Research Database (Denmark)

    Veldhuis, Djuke

    2015-01-01

    Whether you are applying for funding, telling a family member about your research or engaging the public, your success will depend on how well you communicate. Persuading people that your research should be prioritised and funded relies on being a solid negotiator and developing political nous; b......; but these skills are also rooted in communication. One way to do this is by challenging yourself to summarise your research in a short, sharp, three-minute elevator pitch, or ‘flash talk’....

  11. Flash CS3 The Missing Manual

    CERN Document Server

    Grover, Chris

    2008-01-01

    Flash CS3, the latest version of the premier tool for creating web animations and interactive web sites, can be intimidating to learn. This entertaining reference tutorial provides a reader-friendly animation primer and a guided tour of all the program's tools and capabilities. Beginners will learn to use the software in no time, and experienced users will quickly take their skills to the next level.

  12. Mechanisms of Flash Sintering in Cubic Zirconia

    OpenAIRE

    Downs, John Axel

    2013-01-01

    The recently discovered flash sintering technique has shown that the application of a sufficiently large dc electric field (E-field) to a ceramic during sintering can cause sintering at temperatures several hundred degrees below conventional temperatures with sintering rates that allow for sintering in seconds rather than hours. This technique has already been demonstrated in wide range of ceramic materials including ionic conductors, electronic conductors, semi-conductors and insulators. Th...

  13. Membuat Game Kuis Menggunakan Macromedia Flash 8

    OpenAIRE

    Lumban Gaol, Cindi N

    2016-01-01

    In the final project , the author makes an application quiz games . This application is a medium of learning that helps students to study for a quiz pep contained in this application relate to the lessons in school . Methods and design a quiz game designed by using software Macromedia Flash 8 as the programming language , script editor program , and is also used to design this application . This study was made aiming to broaden how to create a quiz game simple one. Word Keys : Mac...

  14. Magnesia-Chrome Refractories for Flash Furnace

    Institute of Scientific and Technical Information of China (English)

    LI Yong; CHEN Kaixian; LU Xinghua; LIU Jianlong; SUN Jialin; HONG Yanruo

    2002-01-01

    The rapid development of our country's heavy nonferrous metallurgical technology and the revolution in new type of heavynon-ferrous metallurgical furnace have imposed more critical demand on the refractory materials ,i. e. high quality and long service life. This paper presents the domestic status of the refractories for flash furnace , briefly describes the wear of the refractory used , and it is considered that the domestic in refractories for flashfurnace can be surely realized.

  15. A Comparative Study of Reduced Variables Based Flash and Conventional Flash

    DEFF Research Database (Denmark)

    Michelsen, Michael Locht; Yan, Wei; Stenby, Erling Halfdan

    Speeding up flash calculation is a central issue in compositional reservoir simulations since phase equilibrium calculation is the most time-consuming part in those simulations. The reduced variables methods, or the reduction methods, reformulate the original phase equilibrium problem with a smal......Speeding up flash calculation is a central issue in compositional reservoir simulations since phase equilibrium calculation is the most time-consuming part in those simulations. The reduced variables methods, or the reduction methods, reformulate the original phase equilibrium problem....... Most of the studies in the last decade suggest that the reduced variables methods are much more efficient than the conventional flash method. However, Haugen and Beckner questioned the advantages of the reduced variables methods in their recent paper (SPE 141399). A fair comparison between the reduced...... variables based flash and the conventional flash is not straightforward since the former is difficult to be formulated as unconstrained minimization and involves more complicated composition derivatives. With the recent formulations by Nichita and Graciaa (2010), it is possible to code the reduced variables...

  16. Riders on the storm: selective tidal movements facilitate the spawning migration of threatened delta smelt in the San Francisco Estuary

    Science.gov (United States)

    Bennett, W.A.; Burau, Jon R.

    2015-01-01

    Migration strategies in estuarine fishes typically include behavioral adaptations for reducing energetic costs and mortality during travel to optimize reproductive success. The influence of tidal currents and water turbidity on individual movement behavior were investigated during the spawning migration of the threatened delta smelt, Hypomesus transpacificus, in the northern San Francisco Estuary, California, USA. Water current velocities and turbidity levels were measured concurrently with delta smelt occurrence at sites in the lower Sacramento River and San Joaquin River as turbidity increased due to first-flush winter rainstorms in January and December 2010. The presence/absence of fish at the shoal-channel interface and near the shoreline was quantified hourly over complete tidal cycles. Delta smelt were caught consistently at the shoal-channel interface during flood tides and near the shoreline during ebb tides in the turbid Sacramento River, but were rare in the clearer San Joaquin River. The apparent selective tidal movements by delta smelt would facilitate either maintaining position or moving upriver on flood tides, and minimizing advection down-estuary on ebb tides. These movements also may reflect responses to lateral gradients in water turbidity created by temporal lags in tidal velocities between the near-shore and mid-channel habitats. This migration strategy can minimize the energy spent swimming against strong river and tidal currents, as well as predation risks by remaining in turbid water. Selection pressure on individuals to remain in turbid water may underlie population-level observations suggesting that turbidity is a key habitat feature and cue initiating the delta smelt spawning migration.

  17. Measurement limits in flash thermography

    Science.gov (United States)

    Shepard, Steven M.; Lhota, James R.; Ahmed, Tasdiq

    2009-05-01

    Although active thermography has traditionally been regarded as a qualitative NDT method, its potential for quantitative measurement of thermophysical properties including wall thickness, flaw size and depth, thermal diffusivity or effusivity has been the subject of numerous investigations. Enabled by improvements in IR camera technology and fast, abundant and inexpensive computing power for advanced signal processing, measurement results have been reported using a variety of excitation and signal processing schemes. Results are often presented as a correlation between thermography data and nominal properties or independent measurements by another "validated" method. However, given the diffusion mechanism that underlies thermography, and the quantization and sampling conditions implicit in using an IR camera as a temperature sensor, there are definite limits to what can be achieved in a thermography measurement. While many benefits can be achieved with improved instrumentation, efficient energy insertion or optimized signal processing, ultimately, the limits imposed by diffusion and instrumentation take precedence, and cannot be circumvented. In this paper, the effects of camera frame rate and sensitivity on measurement of the thickness of a slab are examined, using basic 1-dimensional diffusion approximations.

  18. Extreme flash floods in Barcelona County

    Directory of Open Access Journals (Sweden)

    A. Barrera

    2005-01-01

    Full Text Available In this paper the catastrophic and extraordinary floods occurring in Barcelona County (Catalonia, NE Spain are studied, in order to characterise the temporal evolution of extreme flash floods in that area and their main features. These events usually cause economical losses and major problems for undertaking daily activity in Barcelona city. This kind of floods is a very common feature in the North-east of Spain and they are recorded every year in some point of Catalonia. This contribution also shows the frequency of those events, within the framework of all the floods that have occurred in Barcelona since the 14th century, but also describes the flooded area, urban evolution, impacts and the weather conditions for any of most severe events. The evolution of flood occurrence shows the existence of oscillations in the earlier and later modern age periods that can be attributed to climatic variability, evolution of the perception threshold and changes in vulnerability. A great increase of vulnerability can be assumed for the period 1850-1900. The analysis of the time evolution for the Barcelona rainfall series (1854-2000 shows that no trend exists, although, due to the changes in urban planning, flash-floods impact has changed over this time. The number of catastrophic flash floods has diminished, although the extraordinary ones have increased.

  19. The mutagenic potential of high flash aromatic naphtha.

    Science.gov (United States)

    Schreiner, C A; Edwards, D A; McKee, R H; Swanson, M; Wong, Z A; Schmitt, S; Beatty, P

    1989-06-01

    Catalytic reforming is a refining process that converts naphthenes to aromatics by dehydrogenation to make higher octane gasoline blending components. A portion of this wide boiling range hydrocarbon stream can be separated by distillation and used for other purposes. One such application is a mixture of predominantly 9-carbon aromatic molecules (C9 aromatics, primarily isomers of ethyltoluene and trimethylbenzene), which is removed and used as a solvent--high-flash aromatic naphtha. A program was initiated to assess the toxicological properties of high-flash aromatic naphtha since there may be human exposure through inhalation or external body contact. The current study was conducted partly to assess the potential for mutagenic activity and also to assist in an assessment of carcinogenic potential. The specific tests utilized included the Salmonella/mammalian microsome mutagenicity assay, the hypoxanthine-guanine phosphoribosyl transferase (HGPRT) forward mutation assay in CHO cells, in vitro chromosome aberration and sister chromatid exchange (SCE) assays in CHO cells, and an in vivo chromosome aberration assay in rat bone marrow.

  20. FLASH: A finite element computer code for variably saturated flow

    Energy Technology Data Exchange (ETDEWEB)

    Baca, R.G.; Magnuson, S.O.

    1992-05-01

    A numerical model was developed for use in performance assessment studies at the INEL. The numerical model, referred to as the FLASH computer code, is designed to simulate two-dimensional fluid flow in fractured-porous media. The code is specifically designed to model variably saturated flow in an arid site vadose zone and saturated flow in an unconfined aquifer. In addition, the code also has the capability to simulate heat conduction in the vadose zone. This report presents the following: description of the conceptual frame-work and mathematical theory; derivations of the finite element techniques and algorithms; computational examples that illustrate the capability of the code; and input instructions for the general use of the code. The FLASH computer code is aimed at providing environmental scientists at the INEL with a predictive tool for the subsurface water pathway. This numerical model is expected to be widely used in performance assessments for: (1) the Remedial Investigation/Feasibility Study process and (2) compliance studies required by the US Department of Energy Order 5820.2A.

  1. Nuclear fusion and carbon flashes on neutron stars

    Science.gov (United States)

    Taam, R. E.; Picklum, R. E.

    1978-01-01

    This paper reports on detailed calculations of the thermal evolution of the carbon-burning shells in the envelopes of accreting neutron stars for mass-accretion rates of 1 hundred-billionth to 2 billionths of a solar mass per yr and neutron-star masses of 0.56 and 1.41 solar masses. The work of Hansen and Van Horn (1975) is extended to higher densities, and a more detailed treatment of nuclear processing in the hydrogen- and helium-burning regions is included. Results of steady-state calculations are presented, and results of time-dependent computations are examined for accretion rates of 3 ten-billionths and 1 billionth of solar mass per yr. It is found that two evolutionary sequences lead to carbon flashes and that the carbon abundance at the base of the helium shell is a strong function of accretion rate. Upper limits are placed on the accretion rates at which carbon flashes will be important.

  2. Study on Predrying by Spin Flash Dryer for Granulation

    Institute of Scientific and Technical Information of China (English)

    王晓静; 叶鸣; 钱树德

    2004-01-01

    Spin flash dryer has the advantages of both fluidized bed dryer and pneumatic dryer.It has predominance in dealing with thermal sensitive materials.In this paper,the distribution of the air velocity in the spin flash dryer is discussed,which indicates that the rotating air in the dryer chamber can be divided into two areas,potential flow area and plane swirl area.Experiments show that air tangent velocity effects the process of granulation most remarkably.The radial distribution and moisture content of the particles have their intrinsic rules along either the diameter or height of the drying chamber.Besides,the operating parameters of predrying on bleaching powder are optimized.To meet the strict standard of the wet-pressing granulator on the moisture content of the feeder,a narrow lap is made at proper height in the wall of the drying chamber,where a chute and a rotating valve are installed in order to predry the filter cake and remove a part of water.Then the material is fed into the wet-pressing granulator.

  3. Miniature ambulatory skin conductance monitor and algorithm for investigating hot flash events.

    Science.gov (United States)

    Bahr, Dennis E; Webster, John G; Grady, Deborah; Kronenberg, Fredi; Creasman, Jennifer; Macer, Judy; Shults, Mark; Tyler, Mitchell; Zhou, Xin

    2014-02-01

    A skin conductance monitoring system was developed and shown to reliably acquire and record hot flash events in both supervised laboratory and unsupervised ambulatory conditions. The 7.2 × 3.8 × 1.2 cm(3) monitor consists of a disposable adhesive patch supporting two hydrogel electrodes and a reusable, miniaturized, enclosed electronic circuit board that snaps onto the electrodes. The monitor measures and records the skin conductance for seven days without external wires or telemetry and has an event marker that the subject can press whenever a hot flash is experienced. The accuracy of the system was demonstrated by comparing the number of hot flashes detected by algorithms developed during this research with the number identified by experts in hot flash studies. Three methods of detecting hot flash events were evaluated, but only two were fully developed. The two that were developed were an artificial neural network and a matched filter technique with multiple kernels implemented as a sliding form of the Pearson product-moment correlation coefficient. Both algorithms were trained on a 'development' cohort of 17 women and then validated using a second similar 'validation' cohort of 20. All subjects were between the ages of 40 and 60 and self-reported ten or more hot flashes per day over a three day period. The matched filter was the most accurate with a mean sensitivity of 0.92 and a mean specificity of 0.90 using the data from the development cohort and a mean sensitivity of 0.92 and a mean specificity of 0.87 using the data from the validation cohort. The matched filter was the method implemented in our processing software.

  4. Heavy Metal Distribution in Soils near the Almalyk Mining and Smelting Industrial Area, Uzbekistan

    Institute of Scientific and Technical Information of China (English)

    Obidjon KODIROV; Nosir SHUKUROV

    2009-01-01

    The present study demonstrates distribution and chemical forms of heavy metals in soils of the AImalyk mining and smelting industrial area along five transects. The study area is located in Almalyk, Uzbekistan, where the intensification of industrial enterprises negatively impacts the environment. The distribution of 17 heavy metals (Cu, Zn, Pb, Sc, V, Cr, Co, Ni, Ga, Rb, Sr, Y, Zr, Nb,Ba, Th, and U) were studied in 21 sampling locations (21×3=63 soil samples) along five radial transects with a total length of 60 km downwind deposition gradient. Soil samples were collected from the upper layer (0-10 cm) at 4-6 km intervals. As a result of X-ray fluorescence spectrometry analyses by using X-ray fluorescence spectroscopy (XRF, Philips Analytical Ink, USA ), a significant decrease in heavy metal (Cn, Zn, Pb) deposition was found going from the source in a downwind direction. Soil samples taken from the first location (near the pollution sources) showed higher concentrations of Cu, Zn and Pb, and lower concentrations with increasing distance from the source. Obtained data showed different impact of pollution sources to heavy metal deposition and distribution in soils. The Almalyk mining and smelting complex is the major source of Pb, Zn and Cu enrichment in soils. Distribution of other trace elements does not exceed background content and suggests lithogenic background. This allowed us to divide these elements into two groups: (1) technogenic (Cu, Zn and Pb); and (2) iithogenic (Sc, V, Cr, Co,Ni, Ga, Rb, Sr, Y, Zr, Nb, Ba, Th and U) origins.

  5. Potentially toxic element phytoavailability assessment in Technosols from former smelting and mining areas.

    Science.gov (United States)

    Qasim, Bashar; Motelica-Heino, Mikael; Joussein, Emmanuel; Soubrand, Marilyne; Gauthier, Arnaud

    2015-04-01

    This study reports the chemical bioavailability of several potentially toxic elements (Zn, Pb, Cd, As, and Sb) in contaminated Technosols from two former smelting and mining areas. Though these elements have long been recognized as potentially harmful elements, understanding of their toxicity and environmental behavior in Technosols developed on former mining and smelting sites are more limited, particularly for As and Sb. Surface soils were sampled from metallophyte grassland contaminated with Zn, Pb, and Cd located at Mortagne-du-Nord (North France) and from a former mining settling basin contaminated with As, Pb, and Sb located at la Petite Faye (Limoges, France). Various selective single extraction procedures (CaCl2, NaNO3, NH4NO3, DTPA, and EDTA) were used together with germination tests with dwarf beans whose shoots were analyzed for their potentially toxic element concentrations after 21 days of growth. The extraction capacity of the potentially toxic elements followed the order EDTA > DTPA > NH4NO3 > CaCl2 > NaNO3 for both studied areas. Pearson's correlation coefficient analysis between the concentrations of potentially toxic elements accumulated in bean primary leaves or their mineral mass with their extractable concentrations showed a positive significant correlation with dilute CaCl2 and nitrate solutions extraction procedures. In contrast, for all studied elements, except Pb, the complexing and chelating extractants (EDTA and DTPA) exhibited poor correlation with the dwarf bean leaves concentrations. Moreover, results showed that the 0.01 M CaCl2 extraction procedure was the most suitable and provided the most useful indications of metal phytoavailability for studied elements.

  6. 复杂难处理金精矿还原固硫熔炼富集金%Enriching gold from refractory gold concentrate by reducing sulfur-retention smelting

    Institute of Scientific and Technical Information of China (English)

    罗虹霖; 刘维; 覃文庆; 刘瑞增; 郑永兴; 杨康; 韩俊伟

    2014-01-01

    提出一种处理复杂难处理金精矿的新工艺,主要包括还原固硫熔炼富集金和电解分离铅金两种主要工序。研究其中还原固硫熔炼富集金,分析熔炼温度、铁加入量、铅加入量以及熔炼时间等因素对金直收率的影响,确定最佳工艺条件如下:添加四氧化三铁、废旧铅酸蓄电池胶泥、氧化钙和焦炭的质量分数分别是金精矿质量的95%、86%、22%和10%,样品在1100℃下熔炼1 h后在1200℃保温30 min,金的直收率和总收率分别达到97.02%和98.53%,金得到有效富集,由原金精矿中金含量18.05 g/t提高到铅合金中金含量49.56 g/t,含量提高约1.73倍。%A new technology composed of two main processes, namely, enriching gold by reducing sulfur-retention smelting and electrolysis to separate lead and gold, was proposed for the treatment of refractory gold concentrates. The processes of reducing sulfur-retention smelting were investigated. The effects of smelting temperature, iron addition amount, lead addition amount and smelting time on direct recovery rate of gold were analyzed. The results show that the optimum conditions are as follow:the addition amount of Fe3O4, lead-acid battery colloid sludge, CaO and metallurgical coke is 95%,86%,22% and 10% (mass fraction) of the amount of gold concentrates, respectively, and the sample was melted at 1100℃for 1 h and then at 1200℃for 30 min. Under the optimum conditions, the direct and total recovery ratios of gold are 97.02%and 98.53%, respectively, so gold is collected effectively. The gold content of 49.56 g/t in the lead alloy increases by about 1.73 times than that of 18.05 g/t in the gold concentrate.

  7. Flash memories economic principles of performance, cost and reliability optimization

    CERN Document Server

    Richter, Detlev

    2014-01-01

    The subject of this book is to introduce a model-based quantitative performance indicator methodology applicable for performance, cost and reliability optimization of non-volatile memories. The complex example of flash memories is used to introduce and apply the methodology. It has been developed by the author based on an industrial 2-bit to 4-bit per cell flash development project. For the first time, design and cost aspects of 3D integration of flash memory are treated in this book. Cell, array, performance and reliability effects of flash memories are introduced and analyzed. Key performance parameters are derived to handle the flash complexity. A performance and array memory model is developed and a set of performance indicators characterizing architecture, cost and durability is defined.   Flash memories are selected to apply the Performance Indicator Methodology to quantify design and technology innovation. A graphical representation based on trend lines is introduced to support a requirement based pr...

  8. Onset conditions for flash sintering of UO2

    Science.gov (United States)

    Raftery, Alicia M.; Pereira da Silva, João Gustavo; Byler, Darrin D.; Andersson, David A.; Uberuaga, Blas P.; Stanek, Christopher R.; McClellan, Kenneth J.

    2017-09-01

    In this work, flash sintering was demonstrated on stoichiometric and non-stoichiometric uranium dioxide pellets at temperatures ranging from room temperature (26 °C) up to 600 °C . The onset conditions for flash sintering were determined for three stoichiometries (UO2.00, UO2.08, and UO2.16) and analyzed against an established thermal runaway model. The presence of excess oxygen was found to enhance the flash sintering onset behavior of uranium dioxide, lowering the field required to flash and shortening the time required for a flash to occur. The results from this study highlight the effect of stoichiometry on the flash sintering behavior of uranium dioxide and will serve as the foundation for future studies on this material.

  9. PENGEMBANGAN MEDIA SMILE-FLASH BERPENDEKATAN CHEMO-EDUTAINMENT PADA MATERI KELARUTAN DAN HASIL KALI KELARUTAN

    Directory of Open Access Journals (Sweden)

    Yan Sandi Nurfitrasari

    2016-01-01

    Full Text Available Media smile-flash merupakan media yang di dalamnya terdapat unsur simulasi, materi, dan lagu. Dengan menyisipkan lagu dalam pembelajaran, proses pembelajaran akan lebih menyenangkan sehingga diharapkan dapat meningkatkan pemahaman siswa. Penelitian ini bertujuan untuk (1 mengetahui pengaruh penggunaan media tersebut pada peningkatan pemahaman konsep, dan (2 mengetahui respon siswa terhadap menggunakan media tersebut dalam pembelajaran. Penelitian ini merupakan penelitian pengembangan (R&D dengan subjek penelitan adalah siswa kelas XI IPA di sebuah sekolah di Magelang. Objek penelitian adalah media smile-flash dengan pendekatan chemo-edutainment pada materi kelarutan dan hasil kali kelarutan. Tahap pengembangan media smile-flash dengan pendekatan chemo-edutainment dilakukan dengan: (1 pendefinisian, (2 perancangan, dan (3 pengembangan. Instrumen penelitian berupa angket validasi, angket respon siswa dan soal-soal peningkatan pemahaman konsep. Media dinyatakan layak ditinjau dari aspek materi, media, dan bahasa dengan persentase rata-rata sebesar 82,5%. Hasil penelitian menunjukkan bahwa (1 penggunaan media berpengaruh positif terhadap pemahaman konsep siswa, terbukti thitung (12,24 lebih besar dari tkritis (2,05 dan (2 pembelajaran menggunakan media smile-flash dengan pendekatan chemo-edutainment mendapatkan respon positif dari siswa. Smile-flash media is a medium in which there is an element of simulation, material, and songs. By inserting song learning, the learning process will be more fun that is expected to increase students' understanding. This study aims to (1 know the influence of the media on an improved understanding of the concept, and (2 determine the response of students to use the media in learning. This study is a research & development (R & D with a research subject is class XI IPA at a school in Magelang. The object of research is a medium-flash smile with chemo-edutainment approach to the material solubility and solubility

  10. Multi-channel analyzer controlled by applet and flash

    Institute of Scientific and Technical Information of China (English)

    2002-01-01

    Both java applet and flash were applied to emulate virtual panel of multi-channel pulse height analyzer (MCA), and Microsoft IE browser was used to control MCA through internet to measure the γ-ray energy spectrum of 137Cs. It Was shown that most of the work completed by applet can be done by flash too, and with flash, more beautiful panel of the remote controlled instruments can be easily designed.

  11. Multi—channel analyzer controlled by applet and flash

    Institute of Scientific and Technical Information of China (English)

    HUANGWen-Da

    2002-01-01

    Both java applet and flash were applied to emulate virtual panel of multi-channel pulse height analyzer(MCA),and Microsoft IE browser was used to control MCA through internet to measure the γ-ray energy spectrum of 137Cs.It was shown that most of the work completed by applet can be done by flash too,and with flash,more beautiful panel of the remote controlled instruments can be easily designed.

  12. Improving the flash flood frequency analysis applying dendrogeomorphological evidences

    Science.gov (United States)

    Ruiz-Villanueva, V.; Ballesteros, J. A.; Bodoque, J. M.; Stoffel, M.; Bollschweiler, M.; Díez-Herrero, A.

    2009-09-01

    Flash floods are one of the natural hazards that cause major damages worldwide. Especially in Mediterranean areas they provoke high economic losses every year. In mountain areas with high stream gradients, floods events are characterized by extremely high flow and debris transport rates. Flash flood analysis in mountain areas presents specific scientific challenges. On one hand, there is a lack of information on precipitation and discharge due to a lack of spatially well distributed gauge stations with long records. On the other hand, gauge stations may not record correctly during extreme events when they are damaged or the discharge exceeds the recordable level. In this case, no systematic data allows improvement of the understanding of the spatial and temporal occurrence of the process. Since historic documentation is normally scarce or even completely missing in mountain areas, tree-ring analysis can provide an alternative approach. Flash floods may influence trees in different ways: (1) tilting of the stem through the unilateral pressure of the flowing mass or individual boulders; (2) root exposure through erosion of the banks; (3) injuries and scars caused by boulders and wood transported in the flow; (4) decapitation of the stem and resulting candelabra growth through the severe impact of boulders; (5) stem burial through deposition of material. The trees react to these disturbances with specific growth changes such as abrupt change of the yearly increment and anatomical changes like reaction wood or callus tissue. In this study, we sampled 90 cross sections and 265 increment cores of trees heavily affected by past flash floods in order to date past events and to reconstruct recurrence intervals in two torrent channels located in the Spanish Central System. The first study site is located along the Pelayo River, a torrent in natural conditions. Based on the external disturbances of trees and their geomorphological position, 114 Pinus pinaster (Ait

  13. The echo-enabled harmonic generation options for FLASH II

    CERN Document Server

    Deng, Haixiao; Faatz, Bart

    2011-01-01

    FLASH II is an upgrade to the existing free electron laser (FEL) FLASH. The echo-enabled harmonic generation (EEHG) scheme is proposed to be a potential seeding option of FLASH II. In this paper, the possibility of EEHG operation of FLASH II is investigated for the first time. With a combination of existing numerical codes, i.e. a laser-beam interaction code in an undulator (LBICU), a beam tracking code in a chicane (ELEGANT) and an universal FEL simulating code (GENESIS), the effects of beam energy chirp and coherent synchrotron radiation (CSR) on EEHG operation are studied as well. In addition, several interesting issues concerning EEHG simulation are discussed.

  14. Flash CS5.5 The Missing Manual

    CERN Document Server

    Grover, Chris

    2011-01-01

    You can build everything from simple animations to full-fledged iOS and Android apps with Flash CS5.5, but learning this complex program can be difficult-unless you have this fully updated, bestselling guide. Learn how to create gorgeous Flash effects even if you have no programming experience. With Flash CS5.5: The Missing Manual, you'll move from the basics to power-user tools with ease. Learn animation basics. Discover how to turn simple ideas into stunning animations.Master Flash's tools. Learn the animation and effects tools with clear explanations and hands-on examples.Use 3D effects. R

  15. Copper Recovery from Yimen Copper Smelting Slag%易门铜冶炼渣选铜试验

    Institute of Scientific and Technical Information of China (English)

    谢贤; 杨子轩; 童雄; 侯凯; 黎继永

    2015-01-01

    The composition of Yimen copper smelting slag was complex,with Cu grade of 1. 83%. Main copper minerals are copper sulfide,accounting for 94. 54% of total copper. In order to high efficiently recover copper,mineral processing tests were carried out. The results showed that,at the grinding fineness of the-0. 045 mm accounted for 90%,through the process of one roughing-three cleaning-two scavenging,copper concentrate with copper grade of 18. 27% and recovery of 84. 86%,and silver grade of 76. 20 g/t and recovery of 44. 06% was obtained separately. The beneficiation process selected is simple,which can better recover the copper,and comprehensively recover the silver. It is the ideal process for copper recovery from the sam-ple.%易门铜冶炼渣成分复杂,铜品位为1.83%,主要铜矿物为硫化铜,占总铜的94.54%。为高效回收其中的铜,进行了选矿试验研究。结果表明,在磨矿细度为-0.045 mm占90%的情况下,采用1粗3精2扫、中矿顺序返回浮选流程处理该试样,可获得铜品位为18.27%、含银76.20g/t、铜回收率为84.86%、银回收率为44.06%的铜精矿。试验确定的选矿工艺流程较简单,不仅对铜有较好的回收效果,而且综合回收了其中的银,是该试样中铜的理想回收工艺。

  16. The Isasmelt process

    Energy Technology Data Exchange (ETDEWEB)

    Barrett, K.R. (MIM Technology Marketing Ltd., Northfleet (United Kingdom))

    1993-01-01

    The Isasmelt process was developed at Mt Isa Mines Ltd. in Queensland. The process was initially developed for the treatment of lead concentrate. After successful application of the process to lead production a pilot plant was built for the treatment of copper concentrate to produce copper matte. This was successful and as a result Mt Isa Mines decided to build a new copper smelter with a capacity of 180,000 t copper/ a in copper matte. Further commercialisation of the process has resulted in the construction of further plants for lead, nickel and copper production. Mt Isa Mines Ltd. has been associated with CSIRO (Commonwealth Scientific Industrial Research Organisation) in the development of the Isasmelt process since 1977, when a Sirosmelt lance was tested for reducing copper converter slags. Thermodynamic modelling and cruicible scale investigations on a lead smelting process were initiated in 1978. After further work on a 120 kg/h pilot plant the Isasmelt process for lead concentrate smelting was patented jointly by Mt Isa Mines and CSIRO. Since then a 5 t/h demonstration plant was commissioned 1983/85 for smelting and reduction. Finally in 1991 a commercial scale plant with a capacity of 60,000 t/a was commissioned. (orig.).

  17. Studies on the analysis of pesticide residues in foods (XL) PCB (polychlorinated biphenyls) residues in imported smelt fished from the Canadian Great Lakes

    National Research Council Canada - National Science Library

    Sekita, H; Sasaki, K; Kawamura, Y; Takeda, M; Uchiyama, M

    1987-01-01

    The inspection of PCB (polychlorinated biphenyls) residues in pond smelt samples imported from Canada in June, 1983, fished from Lake Erie, one of the Great Lakes, was performed by gas chromatography with ECD...

  18. Flash floods in Mediterranean ephemeral streams in Valencia Region (Spain)

    Science.gov (United States)

    Camarasa-Belmonte, Ana M.

    2016-10-01

    Ephemeral streams are typical Mediterranean fluvial systems with high risk of flash flooding, and few data are available about these systems in most locales. However, the SAIH network (Automatic Hydrological Information Systems) of the Jucar River Water Authority has been providing detailed information about ephemeral streams in Spain every 5 min since 1988. Using these data, we evaluated the processes of rainfall-runoff conversion and flood generation in five Mediterranean ephemeral streams ranging in size from 25 to 450 km2. To provide a general framework for hydrological analysis, the study included 142 flash flood events registered between 1989 and 2007. A more detailed analysis was conducted for the Carraixet Basin under the dry antecedent moisture condition (AMC I) to evaluate the influence of rainfall on the basin's response. A simple index called Momentum of Maximum Intensity (MMI) was developed to describe the influence of rainfall intensity on hydrograph. Correlations between the main indicators of precipitation and flow also were assessed. Results showed that flash floods were generally generated by average accumulated rainfall of around 100 mm at high intensities that could exceed 300 mm/h. Initial abstractions and average water losses during the rainfall-runoff conversion processes were very important (runoff coefficients of 6% and runoff thresholds of 62 mm). No correlation was found between initial abstractions (Ia) calculated from the basin characteristics and runoff thresholds (P0) empirically obtained, which create some doubts about the validity of Ia method for predicting floods in ephemeral streams. Accumulated rainfall was very important for flood volume, peak flow and water balance indicators, whereas intensity indicators were more related to the response times of the basins. Rainfall intensity variables influenced lag time. Accumulated rainfall, in combination with high reduced mean intensity and low persistence, were a good predictor for

  19. Laser Flash Photolysis Studies on Gallic Acid

    Institute of Scientific and Technical Information of China (English)

    ZHU Hong-Ping; ZHAO Hong-Wei; ZHANG Zhao-Xia; WANG Wen-Feng; YAO Si-De

    2006-01-01

    The transient species of gallic acid (GA) have been studied by 266 nm nanosecond laser flash photolysis in aqueous solution and acetonitrile. The intermediate with absorption at 320 nm was identified as excited triplet state (3GA*), the decay rates of which were obtained in aqueous solution and acetonitrile respectively. Energy transfer from 3GA* to β-carotene was observed and the energy transfer rate constant kent was determined to be 2.2 × 109 mol-1·L·s-1. GA underwent photoionization during photolysis and the quantum yield of photoionization was determined to be 0.12 at room temperature with KI as a reference.

  20. Animación con Flash

    OpenAIRE

    Agelet Ordobàs, Ferran; Villar Posada, Feliciano

    2009-01-01

    Flash es una aplicación informática producida por la empresa de software norteamericana Macromedia, que se utiliza principalmente para la generación de páginas web animadas e interactivas. Este programa se está convirtiendo en un estándar para la creación de contenidos animados y altamente interactivos para ser distribuidos en la Red. Este tutorial pretende recorrer el camino necesario para llegar a conocer las posibilidades de la aplicación sin experiencia previa. El usuario interesado tiene...

  1. Influence of Pressure in Flash Sintering Technique

    Science.gov (United States)

    Pcheliakov, D. A.; Yurlova, M. S.; Grigoryev, E. G.; Olevsky, E. A.

    An innovative pressure-assisted flash-sintering technique has been developed to investigate the effect of pressure applied on microstructure and the sintering behavior of titanium dioxide. There are numerous applications for titanium dioxide in ceramics including microeletronics, glass ceramics, refractive materials, structural ceramics and titanium-containing ceramic materials and chemical intermediates. The traditional sintering of titanium dioxide usually requires several hours at over 1200 °C. The conducted research indicates that titanium dioxide can be sintered to full density in only a few seconds at 800-1000 °C, when subjected to a DC electrical field at a certain temperature moment.

  2. Incoherent-light-flash annealing of phosphorus-implanted silicon

    Science.gov (United States)

    Correra, L.; Pedulli, L.

    1980-07-01

    Incoherent light pulses emitted from a xenon flash lamp were used to anneal radiation damage in (100) silicon implanted with 2×1015 31P+/cm2 at 100 keV. Electrical carrier concentration has been determined by means of differential sheet resistivity and Hall effect together with the anodic oxidation stripping technique; the surface photovoltage technique has been used to evaluate bulk lifetime and Rutherford backscattering and transmission electron microscopy for analysis of radiation damage. Damage recovery appears to take place via a solid phase epitaxial process. Electrical activity and carrier mobility values of samples annealed by incoherent light are similar to those obtained by laser, electron beam, and furnace annealing. The bulk lifetime of minority carriers is not degraded.

  3. Operational flash flood forecasting platform based on grid technology

    Science.gov (United States)

    Thierion, V.; Ayral, P.-A.; Angelini, V.; Sauvagnargues-Lesage, S.; Nativi, S.; Payrastre, O.

    2009-04-01

    Flash flood events of south of France such as the 8th and 9th September 2002 in the Grand Delta territory caused important economic and human damages. Further to this catastrophic hydrological situation, a reform of flood warning services have been initiated (set in 2006). Thus, this political reform has transformed the 52 existing flood warning services (SAC) in 22 flood forecasting services (SPC), in assigning them territories more hydrological consistent and new effective hydrological forecasting mission. Furthermore, national central service (SCHAPI) has been created to ease this transformation and support local services in their new objectives. New functioning requirements have been identified: - SPC and SCHAPI carry the responsibility to clearly disseminate to public organisms, civil protection actors and population, crucial hydrologic information to better anticipate potential dramatic flood event, - a new effective hydrological forecasting mission to these flood forecasting services seems essential particularly for the flash floods phenomenon. Thus, models improvement and optimization was one of the most critical requirements. Initially dedicated to support forecaster in their monitoring mission, thanks to measuring stations and rainfall radar images analysis, hydrological models have to become more efficient in their capacity to anticipate hydrological situation. Understanding natural phenomenon occuring during flash floods mainly leads present hydrological research. Rather than trying to explain such complex processes, the presented research try to manage the well-known need of computational power and data storage capacities of these services. Since few years, Grid technology appears as a technological revolution in high performance computing (HPC) allowing large-scale resource sharing, computational power using and supporting collaboration across networks. Nowadays, EGEE (Enabling Grids for E-science in Europe) project represents the most important

  4. Cuinse2 Thin Film For Solar Cell By Flash Evaporation

    Directory of Open Access Journals (Sweden)

    A.H. Soepardjo

    2009-11-01

    Full Text Available Deposition of thin films for material solar cell CuInSe2 are relatively simple. In this research mainly focused on the use of flash evaporation method, and the material created can then be characterized by optical and electrical properties. The optical characterization is done by X-ray Diffraction (XRD, Energy Dispersive Spectroscopy (EDS, and transmission and reflection by UV-VIS spectrophotometry. Electrical characterization is done by utilizing the Hall effect equipment. From these characterization, the atomic structure, absorption coefficient, energy gap, material type, composition of each elements and the mobility of CuInSe2 can be measured and determined. During process evaporation were carried out at substrate temperatures the range between 20ºC-415ºC.

  5. Warm dense matter and Thomson scattering at FLASH

    Energy Technology Data Exchange (ETDEWEB)

    Faeustlin, Roland Rainer

    2010-05-15

    X-ray free electron lasers are powerful tools to investigate moderately to strongly correlated solid density low temperature plasmas, named warm dense matter. These plasmas are of most interest for astrophysics and laser plasma interaction, particularly inertial confinement fusion. This work utilizes the ultrashort soft x-ray pulse duration and high brilliance of the free electron laser in Hamburg, FLASH, to generate warm dense matter and to study its ultrafast processes. The techniques applied are absorption measurement, emission spectroscopy and Thomson scattering. Radiative hydrodynamics and Thomson scattering simulations are used to investigate the impact of temperature and density gradients in the sample and to fit the experimental data. The measurements result in a comprehensive picture of soft x-ray matter interaction related to warm dense matter and yield insight into ultrafast equilibration and relaxation mechanisms, in particular impact ionization and radiative recombination. (orig.)

  6. Multi-scale hydrometeorological observation and modelling for flash flood understanding

    OpenAIRE

    Braud, I.; Ayral, P.-A.; Bouvier, C.; Branger, F.; Delrieu, G.; Coz, J.; Nord, G.; Vandervaere, J.-P.; Anquetin, S.; Adamovic, M.; Andrieu, J.; Batiot, C.; Boudevillain, B.; Brunet, P; Carreau, J.

    2014-01-01

    This paper presents a coupled observation and modelling strategy aiming at improving the understanding of processes triggering flash floods. This strategy is illustrated for the Mediterranean area using two French catchments (Gard and Ardèche) larger than 2000 km2. The approach is based on the monitoring of nested spatial scales: (1) the hillslope scale, where processes influencing the runoff generation and its concentration can be tackled; (2) the small to medium cat...

  7. In situ monitoring of flash-light sintering of copper nanoparticle ink for printed electronics.

    Science.gov (United States)

    Hwang, Hyun-Jun; Chung, Wan-Ho; Kim, Hak-Sung

    2012-12-07

    In this work, a flash-light sintering process for Cu nanoinks was studied. In order to precisely monitor the milliseconds flash-light sintering process, a real-time Wheatstone bridge electrical circuit and a high-rate data acquisition system were used. The effects of several flash-light irradiation conditions (irradiation energy, pulse number, on-time, and off-time) and the effects of the amount of poly(N-vinylpyrrolidone) in the Cu nanoink on the flash-light sintering process were investigated. The microstructures of the sintered Cu films were analyzed by scanning electron microscopy. To investigate the oxidation or reduction of the oxide-covered copper nanoparticles, a crystal phase analysis using x-ray diffraction was performed. In addition, the sheet resistance of Cu film was measured using a four-point probe method. From this study, it was found that the flash-light sintered Cu nanoink films have a conductivity of 72 Ωm/sq without any damage to the polyimide substrate. Similar nanoinks are expected to be widely used in printed and flexible electronics products in the near future.

  8. The attentional modulation of the flash-lag effect

    Directory of Open Access Journals (Sweden)

    M.V.C. Baldo

    2002-08-01

    Full Text Available If a dot is flashed in perfect alignment with a pair of dots rotating around the visual fixation point, most observers perceive the rotating dots as being ahead of the flashing dot (flash-lag effect. This perceptual effect has been interpreted to result from the perceptual extrapolation of the moving dots, the differential visual latencies between flashing and moving stimuli, as well as the modulation of attentional mechanisms. Here we attempted to uncouple the attentional effects brought about by the spatial predictability of the flashing dot from the sensory effects dependent on its visual eccentricity. The stimulus was a pair of dots rotating clockwise around the fixation point. Another dot was flashed at either the upper right or the lower left of the visual field according to three separate blocked situations: fixed, alternate and random positions. Twenty-four participants had to judge, in all three situations, the location of the rotating dots in relation to the imaginary line connecting the flashing dot and the fixation point at the moment the dot was flashed. The flash-lag effect was observed in all three situations, and a clear influence of the spatial predictability of the flashing dot on the magnitude of the perceptual phenomenon was revealed, independently of sensory effects related to the eccentricity of the stimulus in the visual field. These findings are consistent with our proposal that, in addition to sensory factors, the attentional set modulates the magnitude of the differential latencies that give rise to the flash-lag phenomenon.

  9. Flash Thermography to Evaluate Porosity in Carbon Fiber Reinforced Polymer (CFRPs

    Directory of Open Access Journals (Sweden)

    Carosena Meola

    2014-02-01

    Full Text Available It is a fact that the presence of porosity in composites has detrimental effects on their mechanical properties. Then, due to the high probability of void formation during manufacturing processes, it is necessary to have the availability of non-destructive evaluation techniques, which may be able to discover the presence and the distribution of porosity in the final parts. In recent years, flash thermography has emerged as the most valuable method, but it is still not adequately enclosed in the industrial enterprise. The main reason of this is the lack of sufficient quantitative data for a full validation of such a technique. The intention of the present work is to supply an overview on the current state-of-the-art regarding the use of flash thermography to evaluate the porosity percentage in fiber reinforced composite materials and to present the latest results, which are gathered by the authors, on porous carbon fiber reinforced polymer laminates. To this end, several coupons of two different stacking sequences and including a different amount of porosity are fabricated and inspected with both non-destructive and destructive testing techniques. Data coming from non-destructive testing with either flash thermography or ultrasonics are plotted against the porosity percentage, which was previously estimated with the volumetric method. The new obtained results are a witness to the efficacy of flash thermography. Some key points that need further consideration are also highlighted.

  10. A Histogram-Based Static-Error Correction Technique for Flash ADCs

    Institute of Scientific and Technical Information of China (English)

    Armin Jalili; J Jacob Wikner; Sayed Masoud Sayedi; Rasoul Dehghani

    2011-01-01

    High-speed, high-accuracy data converters are attractive for use in most RF applications. Such converters allow direct conversion to occur between the digital baseband and the antenna. However, high speed and high accuracy make the analog components in a converter more complex, and this complexity causes more power to be dissipated than if a traditional approach were taken. A static calibration technique for flash analog-to-digital converters (ADCs) is discussed in this paper. The calibration is based onhistogram test methods, and equivalent errors in the flash ADC comparators are estimated in the digital domain without any significant changes being made to the ADC comparators. In the trimming process, reference voltages are adjusted to compensate for static errors. Behavioral-level simulations of a moderate-resolution 8-bit flash ADC show that, for typical errors, ADC performance is considerably improved by the proposed technique. As a result of calibration, the differential no.nlinearities (DNLs) are reduced on average from 4 LSB to 0.5 LSB, and the integral nonlinearities (INLs) are reduced on average from 4.2 LSB to 0.35 LSB. Implementation issues for this proposed technique are discussed in our subsequent paper, “A Histogram-Based Static-Error Correction Technique for Flash ADCs: Implementation Aspects. ”

  11. Study of laser preheat in magnetic liner inertial fusion using the AMR code FLASH

    Science.gov (United States)

    Adams, Marissa; Jennings, Christopher; Slutz, Stephen; Peterson, Kyle; Gourdain, Pierre-Alexandre; University of Rochester; Sandia National Laboratories Collaboration

    2016-10-01

    Magnetic Liner Inertial Fusion (MagLIF) on the Z Pulsed Power Accelerator involves three processes: magnetization, preheat, and compression. An issue with this scheme is the development of instabilities during laser preheat, where the Z-Beamlet laser system may not deposit energy into deuterium fuel uniformly. This study explores potential mixing between liner and fuel, and inner imprinting of seeds on a beryllium liner that may generate late instability growth and shear, using the Eulerian AMR code FLASH. We further investigate potential instability implications of an additional layer of deuterium-tritium ice, as has been proposed and assess the sensitivity of MagLIF implosions to axial variations in fuel preheat; meanwhile testing the expediency of FLASH for these scenarios. FLASH was developed in part by the DOE NNSA ASC and DOE Office of Science ASCR-supported Flash Center at the University of Chicago. Sandia is a multiprogram laboratory operated by Sandia Corporation, a Lockheed Martin comapny, for the U.S. Department of Energy's National Nuclear Security Administration under contract No. DE-AC04-94AL85000.

  12. Flash Flood Detection in Urban Cities Using Ultrasonic and Infrared Sensors

    KAUST Repository

    Mousa, Mustafa

    2016-07-19

    Floods are the most common type of natural disaster. Often leading to loss of lives and properties in the thousands yearly. Among these events, urban flash floods are particularly deadly because of the short timescales on which they occur, and because of the population density of cities. Since most flood casualties are caused by a lack of information on the impending flood (type, location, severity), sensing these events is critical to generate accurate and detailed warnings and short term forecasts. However, no dedicated flash flood sensing systems, that could monitor the propagation of flash floods, in real time, currently exist in cities. In the present paper, firstly a new sensing device that can simultaneously monitor urban flash floods and traffic congestion has been presented. This sensing device is based on the combination of ultrasonic range-finding with remote temperature sensing, and can sense both phenomena with a high degree of accuracy, using a combination of L1-regularized reconstruction and artificial neural networks to process measurement data. Secondly, corresponding algorithms have been implemented on a low-power wireless sensor platform, and their performance in water level estimation in a 6 months test involving four different sensors is illustrated. The results demonstrate that urban water levels can be reliably estimated with error less than 2 cm, and that the preprocessing and machine learning schemes can run in real-time on currently available wireless sensor platforms.

  13. Pollution level and inhalation exposure of ambient aerosol fluoride as affected by polymetallic rare earth mining and smelting in Baotou, north China

    Science.gov (United States)

    Zhong, Buqing; Wang, Lingqing; Liang, Tao; Xing, Baoshan

    2017-10-01

    Airborne fluoride associated with total suspended particles (TSP) and respirable particulate (PM10) in the rare earth mining and smelting areas were analyzed during August 2012 and March 2013. In March, average concentrations of fluoride bound to TSP in the mining and smelting areas were 0.598 ± 0.626 μg/m3 and 3.615 ± 4.267 μg/m3, respectively, whereas that in August were 0.699 ± 0.801 μg/m3 and 1.917 ± 2.233 μg/m3, respectively. TSP samples were classified into four categories by different sampling periods and locations using Kohonen's self-organizing map, which demonstrates that high airborne fluoride concentrations in March in the smelting area were probably attributed to industrial emissions from smelting activities and wind-blown dust from tailings pond, influenced by meteorologic parameters such as temperature, relative humidity, precipitation and wind speed. The mean daily amount of fluoride inhaled in the mining and smelting areas were estimated to be in the range of 2.77-57.61 μg/day and 3.39-64.32 μg/day, respectively. These results indicate the high potential exposure level of fluoride inhaled for local residents in the polymetallic mining and smelting areas.

  14. Heat transfer characteristics of water film flash evaporation in vacuum ice making%水膜闪蒸真空制冰的换热特性

    Institute of Scientific and Technical Information of China (English)

    纪珺; 章学来; 刘小微; 吴云云; 韩中; 杨阳

    2013-01-01

    A water film flash evaporation vacuum ice-making system is developed. The experiment was carried out to investigate the influence of flash evaporation pressure, thickness and initial temperature of water film on the flash evaporation process. The thickness of the water film was 15, 35, 55 and 75 mm. Initial temperature of water film ranged from 2℃ to 10℃ , and flash evaporation pressure varied from 100 Pa to 600 Pa. The characteristics of the flash evaporation process were recorded using a CCD camera of the visualization system. The experimental results show that under the operating conditions, lower flash evaporation pressure leads to faster change of water film temperature at constant initial temperature of water film. Higher initial temperature of water film makes the water film temperature varies more quickly at constant pressure. As water film thickness increases, the decrease rate of water film temperature reduces. Based on the experimental results, a correlation for water film temperature with flash evaporation pressure, thickness and initial temperature of water film is presented with the maximum error of 24. 19%.

  15. A study on the phenomena of flash-sintering with tetragonal zirconia

    Science.gov (United States)

    Francis, John Stanley Curtis

    accompanies flash sintering. The unusually low processing temperatures and short sintering times portend a potential for a new era in ceramic manufacturing. The energy savings can be substantial, and the tooling costs can be significantly lower. The short sintering times offer the possibility of continuous rather than batch processing of ceramics. These ideas outside the entire scope of this thesis, however, they point toward the potential for broad impact of this research.

  16. Allocation and source attribution of lead and cadmium in maize (Zea mays L.) impacted by smelting emissions.

    Science.gov (United States)

    Bi, Xiangyang; Feng, Xinbin; Yang, Yuangen; Li, Xiangdong; Shin, Grace P Y; Li, Feili; Qiu, Guangle; Li, Guanghui; Liu, Taoze; Fu, Zhiyou

    2009-03-01

    Plants grown in contaminated areas may accumulate trace metals to a toxic level via their roots and/or leaves. In the present study, we investigated the distribution and sources of Pb and Cd in maize plants (Zea mays L.) grown in a typical zinc smelting impacted area of southwestern China. Results showed that the smelting activities caused significantly elevated concentrations of Pb and Cd in the surrounding soils and maize plants. Pb isotope data revealed that the foliar uptake of atmospheric Pb was the dominant pathway for Pb to the leaf and grain tissues of maize, while Pb in the stalk and root tissues was mainly derived from root uptake. The ratio of Pb to Cd concentrations in the plants indicated that Cd had a different behavior from Pb, with most Cd in the maize plants coming from the soil via root uptake.

  17. Anthropoghenic soil contamination connected with active mines, smelting and plants in the Republic of Macedonia

    Directory of Open Access Journals (Sweden)

    Todor Serafimovski

    2014-12-01

    Full Text Available A few anthropogenic pollutants at the territory of the Republic of Macedonia, were studied, three Pb-Zn mines with three mi­lls, one copper mine with mill and copper leaching facility, one Pb-Zn smelting and several mines and factories for raw minerals such is the Usje in our capital Skopje. At the Usje factory were measured values in ranges of 1.46÷2.23% Fe, 440÷940 mg kg-1Mn, 93.4÷104.71mg kg-1Ni, 58.57÷83.1 mg kg-1Zn, 23.1÷34.9 mgkg-1 Pb, 42.30÷60.3 mg kg-1 Cu and 0.59÷1.61 mgkg-1Cd. The concentrations of heavy metals at Veles former smelting Pb-Zn plant were in the range: 20÷1823 mg kg-1Pb, 29÷2395 mg kg-1Zn, 28÷65 mgkg-1Cd, 27÷81 mg kg-1 Cu, 39÷164 mg kg-1Ni, 508÷938 mgkg-1Mn and 1.6÷3.8% Fe, all of them above reference values. Around the Feni smelting plant concentrations of particular pollution elements were in the range: 16÷31 mg kg-1Pb, 117÷286 mgkg-1Zn, 13÷30 mg kg-1Co, 43÷119 mg kg-1 Cu, 158÷292 mg kg-1Ni, 519÷903 mgkg-1Mn, 119÷236 mg kg-1 Cr and 2.24÷3.79% Fe. At the ToranicaPb-Zn mine all the measured values multiplexed above the standard values. Enri­ch­me­nt factors ranged from, low 3.75 for nickel up to 362.5 for zinc and extreme 1587.5 for lead. The Zletovo Pb-Zn mine has been characterized by all the measured values multiplexed above the standard values with an exception of nickel. Enrichment factors ranged from mediate ones such were those for copper of 20.8, cadmium of 28.7, arsenic of 32.5 up to high ones for zinc with 341.7 and lead 925. In regards to SasaPb-Zn mine all the measured values multiplexed above the standard values with an exception of nickel. Enrichment factors ranged from low for manganese of 12.14 and arsenic of 15.72, median for copper of 59.15, high for cadmium of 126 and extremely high for zinc with 892.7 and lead 1201.9. In regards to the Bucim copper mine the median values for Cu in samples were 396 mg kg-1 and the ranges from 94.8 to 1171 mg kg-1, for the Topolnica village the

  18. Environmental risk assessment on slag and iron-rich matte produced from reducing-matting smelting of lead-bearing wastes and iron-rich wastes%对含铅及高铁固体废物还原造锍熔炼炉渣和铁锍的环境评价

    Institute of Scientific and Technical Information of China (English)

    柴立元; 吴见珣; 吴延婧; 唐朝波; 杨卫春

    2015-01-01

    还原造锍熔炼技术是可综合回收利用高铁、含铅固体废物的一种新技术。其主要副产物是炉渣和铁锍。采用浸出毒性实验、BCR三步连续浸提以及Hakanson潜在生态风险评价等方法系统地对还原造锍主要副产物和进炉炉料中重金属(Cd、Zn、Pb 和 As)的环境风险进行评价。结果表明,经过还原造锍熔炼后,水淬渣和铁锍中重金属潜在的环境生态风险明显比进炉炉料的低。%A new process for utilization of hazardous lead-bearing wastes and iron-rich wastes by reducing-matting smelting has been developed. The slag (SG) and the iron-rich matte (IRM) are the main by-products from reducing-matting smelting of lead-bearing wastes and iron-rich wastes. The environmental risk of heavy metals (Cd, Zn, Pb and As) in the main by-products versus the charging material for reducing-matting smelting (CM) has been systematically assessed using leaching toxicity test, the three-stage sequential extraction procedure of European Community Bureau of Reference (BCR) and Hakanson Potential Ecological Risk Index Method (PERI). The results demonstrate that the ecological risk level of heavy metals for SG and IRM is significantly reduced after the reducing-matting smelting process compared with that for CM.

  19. Flash pyrolysis fuel oil: BIO-POK

    Energy Technology Data Exchange (ETDEWEB)

    Gust, S. [Neste Oy, Porvoo (Finland)

    1995-12-31

    Flash pyrolysis oil from Ensyn Tech., Canada and Union Fenosa, Spain was combusted with simple pressure atomisation equipment commonly used with light fuel oils in intermediate size (0.1-1 MW) boilers. With a number of modifications to the combustion system, carbon monoxide (CO) and nitrous oxide (NO{sub x}) could be reduced to acceptable levels: CO < 30 ppm and NO{sub x} < 140 ppm. Particulate emissions which were initially very high (Bacharach 4-5) were reduced (Bach. 2-3) by system changes but are still higher than from light fuel oil (Bach. <1). The modifications to the combustion system were: acid resistant progressive cavity pump, higher oil preheat temperature and higher oil pressure than for light fuel oils, refractory section between burner and boiler warmed up to at least 800 deg C. In addition, it was necessary to store pyrolysis oil samples under inert conditions to prevent oxidation and to rinse nozzles with alcohol after shutdown to prevent coking. The complexity and cost of these system modifications are considered to be too great for current grades of flash pyrolysis oil to be sold as a light fuel oil replacement. Improvements to fuel quality will be necessary. The main improvements are lowering of viscosity and improving of stability

  20. Flash Infrared Thermography Contrast Data Analysis Technique

    Science.gov (United States)

    Koshti, Ajay

    2014-01-01

    This paper provides information on an IR Contrast technique that involves extracting normalized contrast versus time evolutions from the flash thermography inspection infrared video data. The analysis calculates thermal measurement features from the contrast evolution. In addition, simulation of the contrast evolution is achieved through calibration on measured contrast evolutions from many flat-bottom holes in the subject material. The measurement features and the contrast simulation are used to evaluate flash thermography data in order to characterize delamination-like anomalies. The thermal measurement features relate to the anomaly characteristics. The contrast evolution simulation is matched to the measured contrast evolution over an anomaly to provide an assessment of the anomaly depth and width which correspond to the depth and diameter of the equivalent flat-bottom hole (EFBH) similar to that used as input to the simulation. A similar analysis, in terms of diameter and depth of an equivalent uniform gap (EUG) providing a best match with the measured contrast evolution, is also provided. An edge detection technique called the half-max is used to measure width and length of the anomaly. Results of the half-max width and the EFBH/EUG diameter are compared to evaluate the anomaly. The information provided here is geared towards explaining the IR Contrast technique. Results from a limited amount of validation data on reinforced carbon-carbon (RCC) hardware are included in this paper.