New diagnostic technology and hidden pits and fissures caries

Directory of Open Access Journals (Sweden)

Fabrizio Guerra

2015-10-01

Full Text Available The accuracy in pits and fissures caries detection is of paramount importance in dental caries primary and secondary prevention. A combination of visual examination and probing is currently the mainstay of occlusal caries diagnosis. Unfortunately, these types of inspection alone may leave a certain number of pit and fissure caries undetected. The Vista Cam iX fluorescence camera (Durr Dental, Bietigheim-Bissingen, Germany is a novel dental diagnostic tool for quantitative assessment of dental caries with high specificity for carious lesions detection. In the presented cases photographic images, representing the visual diagnostic approach, are applied as integration to VistaCam iX Proof images. A step-by-step sequence of inspection and assessment of operative treatment need is presented in a case of hidden pit and fissure caries on a permanent molar. Based on the reported case, it could be observed that VistaCam iX Proof shows promising results in hidden pits and fissures caries detection and could be considered a non-invasive examination method that facilitate the detection of early lesions and a potential diagnostic aid.

24 CFR 3280.611 - Vents and venting.

Science.gov (United States)

2010-04-01

...) Materials—(1) Pipe. Vent piping shall be standard weight steel, wrought iron, brass, copper tube DWV, listed...) Size of vent piping—(1) Main vent. The drain piping for each toilet shall be vented by a 11/2 inch... venting cross section of a 11/2 inch diameter vent, connected to the toilet drain by one of the following...

Flow in fissured porous media

International Nuclear Information System (INIS)

Stichel, Sabine

2014-01-01

The flow simulation in fissured porous media is of importance for hydro-geological applications like ground water contamination in the neighborhood of waste disposal sites, radioactive waste repositories, fossil fuel mining or underground CO2 storage facilities. The permeability within the fissures - that are preferred transport paths - could influence the flow profile. The anisotropic geometry and the excursive parameter changes produce enormous challenges to numerical methods. A low-dimensional approach is used to model then processes within the fissures, acceptable results were reached. Based on the properties of the fissure and flow parameters a criterion was defined that allows to judge whether the application of the low-dimensional approach is sufficient. A dimension-adapting approach is presented that allow the change tp a full-dimensional model according to the criterion.

Radionuclide transport in a single fissure

International Nuclear Information System (INIS)

Eriksen, T.E.

1983-01-01

Radionuclide migration have been studied in natural fissures orieted parallel to the axis of granite drill cores. A short pulse of the radionuclides solution was injected at one end of the fissure and the temporal change in radionuclide concentration of the eluate measured. After several hundred fissure volumes water had been pumped through the fissure following the radionuclide pulse the activity distribution on the fissure surfaces was measured. From the retardation of 152 Eu, 235 Np and 237 Pu it is concluded that these radionuclides are transported in the oxidation states Eu(III), Pu(IV) and Np(V). The distribution coefficients K sub (d) calculated from flow and activity distribution data on the basis of geometric surface area/volume ratios are of the same order as published K sub (d) values obtained from batch equilibrium experiments. (Author)

Radionuclide transport in a single fissure

International Nuclear Information System (INIS)

Eriksen, T.E.

1984-01-01

Radionuclide migration has been studied in natural fissures running parallel to the axes of granitic drill cores. A short pulse of radionuclide solution was injected at one end of the fissure and the temporal change in radionuclide concentration of the eluate measured. At the end of each experiment the fissure was opened and the radionuclide distribution on the fissure surfaces measured. The retardation of 241 Am(III) at pH 8.2 as well as the variation in 235 Np(V) retardation with pH are found to be in good agreement with K d-values obtained in batch experiments. The reduction of (TcO - 4 ) to Tc(IV) leads as expected to increasing retardation.(author)

Hydrodynamic calculation of a filter sand bed type used in the containment venting systems

International Nuclear Information System (INIS)

Cuevas V, D.; Sainz M, E.; Ortiz V, J.

2015-09-01

The filtered venting of the containment has been adopted in European countries to mitigate the consequences of excess pressure containment during a severe accident. When venting has taken place, the fission products are released directly into the environment, unless a filter on the same path is placed, so that various types of filters are used to trap the fission products. The venting filters of the containment currently installed use different filtration technologies that involve more than one medium. Those using water as the first stage of filtration are called wet systems and are equipped with additional steps to remove water drops and fine aerosols emissions. And even they may also be equipped with an element containing certain absorption means for the filtration of gaseous iodine species. Other designs based on filtration of deep bed as the primary retention step; called dry filters, use filtration media of metal fiber, ceramic or sand to trap aerosols. This paper evaluates the hydraulic characteristics of the filter sand bed type designed by EDF as a candidate to be installed in the containment of BWR Mark II (type of primary containment of the nuclear power plant of Laguna Verde). The evaluation of filter sand bed type was performed using the software package of open source OpenFOAM. Models of each zone of the filtered device were generated and through a series of parametric calculations of computational fluid mechanics relevant hydrodynamic characteristics of the device were obtained, such as pressure drops against mass flow rate and pressure fields and speed at different operating conditions. On the other hand, the model validation of the sand bed filter when comparing the results of experimental tests on a sand column of PITEAS program (1985-1986) against OpenFOAM simulation was realized. The results are very close to those obtained experimentally. (Author)

14 CFR 25.975 - Fuel tank vents and carburetor vapor vents.

Science.gov (United States)

2010-01-01

... TRANSPORTATION AIRCRAFT AIRWORTHINESS STANDARDS: TRANSPORT CATEGORY AIRPLANES Powerplant Fuel System § 25.975 Fuel tank vents and carburetor vapor vents. (a) Fuel tank vents. Each fuel tank must be vented from the... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false Fuel tank vents and carburetor vapor vents...

14 CFR 29.975 - Fuel tank vents and carburetor vapor vents.

Science.gov (United States)

2010-01-01

... TRANSPORTATION AIRCRAFT AIRWORTHINESS STANDARDS: TRANSPORT CATEGORY ROTORCRAFT Powerplant Fuel System § 29.975 Fuel tank vents and carburetor vapor vents. (a) Fuel tank vents. Each fuel tank must be vented from the... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false Fuel tank vents and carburetor vapor vents...

European type NPP electric power and vent systems. For safety improvement and proposal of international center

International Nuclear Information System (INIS)

Sugiyama, Kenichiro

2011-01-01

For prevention of reactor accidents of nuclear power plants, multiplicity and redundancy of emergency power would be most important. At station blackout accident, European type manually operated vent operation could minimize release amount of radioactive materials and keep safety of neighboring residents. After Fukushima Daiichi accident, nuclear power plants could not restart operation even after completion of periodical inspection. This article introduced European type emergency power and vent systems in Swiss, Sweden and Germany with state of nuclear power phaseout for reference at considering to upgrade safety and accident mitigation measures for better understanding of the public. In addition, it would be important to recover trust of nuclear technology to continue to disseminate latest information on new knowledge of accident site and decontamination technologies to domestic and overseas people. As its implementation, establishment of Fukushima international center was proposed. (T. Tanaka)

Factors affecting coke size and fissuring during cokemaking part 2

Energy Technology Data Exchange (ETDEWEB)

Merrick Mahoney; Jeff Keating; Susan Woodhouse [BHP Billiton Newcastle Technology Centre (Australia)

2007-12-15

This work addressed the mechanism of fissuring during metallurgical cokemaking and extends on a previous ACARP project. Considerable progress has been made in understanding the mechanism by an integrated modelling work; experimental program. The work points to opportunities for controlling the carbonisation process to achieve required outcomes in terms of coke lump size and distribution. Key outcomes of the work included: A methodology for determination of the minimum spacing between fissures, and the time at which period doublings (i.e. every second fissure stopping) occur, has been developed and implemented. Implementation of the methodology allows the determination of the complete fissure pattern (at least those perpendicular to the oven walls) for a given coke oven/charge configuration. A plausible mechanistic explanation of the formation of lateral fissures (those that are parallel to the oven walls) has been developed. Knowledge of the fissure pattern, combined with the lateral fissuring explanation, enables the determination of typical size and shape of lumps after stabilisation of the coke.

14 CFR 23.975 - Fuel tank vents and carburetor vapor vents.

Science.gov (United States)

2010-01-01

... TRANSPORTATION AIRCRAFT AIRWORTHINESS STANDARDS: NORMAL, UTILITY, ACROBATIC, AND COMMUTER CATEGORY AIRPLANES Powerplant Fuel System § 23.975 Fuel tank vents and carburetor vapor vents. (a) Each fuel tank must be vented... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false Fuel tank vents and carburetor vapor vents...

Chronology and volcanology of the 1949 multi-vent rift-zone eruption on La Palma (Canary Islands)

Science.gov (United States)

Klügel, A.; Schmincke, H.-U.; White, J. D. L.; Hoernle, K. A.

1999-12-01

The compositionally zoned San Juan eruption on La Palma emanated from three eruptive centers located along a north-south-trending rift zone in the south of the island. Seismic precursors began weakly in 1936 and became strong in March 1949, with their foci progressing from the north of the rift zone towards its south. This suggests that magma ascended beneath the old Taburiente shield volcano and moved southward along the rift. The eruption began on June 24, 1949, with phreatomagmatic activity at Duraznero crater on the ridgetop (ca. 1880 m above sea level), where five vents erupted tephritic lava along a 400-m-long fissure. On June 8, the Duraznero vents shut down abruptly, and the activity shifted to an off-rift fissure at Llano del Banco, located at ca. 550 m lower elevation and 3 km to the northwest. This eruptive center issued initially tephritic aa and later basanitic pahoehoe lava at high rates, producing a lava flow that entered the sea. Two days after basanite began to erupt at Llano del Banco, Hoyo Negro crater (ca. 1880 m asl), located 700 m north of Duraznero along the rift, opened on July 12 and produced ash and bombs of basanitic to phonotephritic composition in violent phreatomagmatic explosions ( White and Schmincke, 1999). Llano del Banco and Hoyo Negro were simultaneously active for 11 days and showed a co-variance of their eruption rates indicating a shallow hydraulic connection. On July 30, after 3 days of quiescence at all vents, Duraznero and Hoyo Negro became active again during a final eruptive phase. Duraznero issued basanitic lava at high rates for 12 h and produced a lava flow that descended towards the east coast. The lava contains ca. 1 vol.% crustal and mantle xenoliths consisting of 40% tholeiitic gabbros from the oceanic crust, 35% alkaline gabbros, and 20% ultramafic cumulates. The occurrence of xenoliths almost exclusively in the final lava is consistent with their origin by wall-rock collapse at depth near the end of the eruption

Types of collapse calderas

Energy Technology Data Exchange (ETDEWEB)

Aguirre-Diaz, Gerardo J [Centro de Geociencias, Universidad Nacional Autonoma de Mexico, Campus Juriquilla, Queretaro, Qro., 76230 (Mexico)], E-mail: ger@geociencias.unam.mx

2008-10-01

Three main types of collapse calderas can be defined, 1) summit caldera: those formed at the top of large volcanoes, 2) classic caldera: semi-circular to irregular-shaped large structures, several km in diameter and related to relatively large-volume pyroclastic products, and 3) graben caldera: explosive volcano-tectonic collapse structures from which large-volume, ignimbrite-forming eruptions occurred through several fissural vents along the graben master faults and the intra-graben block faults. These in turn can collapse at least with three styles: 1) Piston: when the collapse occurs as a single crustal block; 2) Trap-door: when collapse occurs unevenly along one side while the opposite side remains with no collapse; 3) Piece-meal: when collapse occurs as broken pieces of the crust on top of the magma chamber.

Research on Integrated Geophysics Detect Potential Ground Fissure in City

Science.gov (United States)

Qian, R.

2017-12-01

North China confined aquifer lied 70 to 200 meters below the earth's surface has been exploited for several decades, which resulted in confined water table declining and has generated a mass of ground fissure. Some of them has reached the surface and the other is developing. As it is very difficult to stop the ground fissure coming into being, measures of avoiding are often taken. It brings great potential risk to urban architecture and municipal engineering. It is very important to find out specific distribution and characteristic of potential ground fissure in city with high resolution. The ground fissure is concealed, therefor, geophysical method is an important technology to detecting concealed ground fissure. However, it is very difficult to detect the characteristics of the superficial part of ground fissure directly, as it lies dozens of meters below and has only scores of centimeters fault displacement. This paper studies applied ground penetration radar, surface wave and shallow refleciton seismic to detect ground fissure. It sets up model of surface by taking advantage of high resolution of ground penetrating radar data, constrains Reilay wave inversion and improves its resolution. The high resolution reflection seismic is good at detecting the geology structure. The data processing and interpretation technique is developmented to avoid the pitfall and improve the aliability of the rusult. The experiment has been conducted in Shunyi District, Beijing in 2016. 5 lines were settled to collect data of integrated geophysical method. Development zone of concealed ground fissure was found and its ultra shallow layer location was detected by ground penetrating radar. A trial trench of 6 meters in depth was dug and obvious ground fissure development was found. Its upper end was 1.5 meters beneath the earth's surface with displacement of 0.3 meters. The favorable effect of this detection has provided a new way for detecting ground fissure in cities of China, such

Treatment of fissure in ano-revisited | Gupta | African Health Sciences

African Journals Online (AJOL)

Methods: This paper outlines a brief account of the present scenario of different techniques available for the treatment of chronic anal fissure. Conclusion: Medical manipulation of the internal sphincter should be a first-line treatment in anal fissure. When this fails or fissures recur, lateral subcutaneous internal sphincterotomy ...

Intracranial lipoma in the sylvian fissure

International Nuclear Information System (INIS)

Ogasawara, Kuniaki; Kinjo, Toshihiko; Onuma, Takehide

1988-01-01

An experience with an operation on a case of intracranial lipoma in the sylvian fissure is reported. A 14-year-old man had complained of attacks of abnormal behavior for 2 years and was diagnosed by a psychiatrist as suffering from temporal epilepsy. A computed tomography (CT) scan indicated an abnormal shadow on the brain, and so he was admitted to our hospital. On admission, the results of physical and neurological examinations were normal. An electroencephalogram recorded irregular δ waves and sharp waves over the right frontotemporal region, however. A CT scan showed a round-shaped, extremely low-density area, with calcification of the wall and without contrast-enhancement, in the left sylvian fissure. No abnormal finding was seen in plain skull X-P or in left-carotid angiography. Left-frontotemporal craniotomy was performed to remove the tumor. A solid yellowish tumor was found in the sylvian fissure and totally removed. Histologically, it proved to be a lipoma. The postoperative course was uneventful, and the patient was discharged without any neurological deficit. We discussed the neuroradiological findings of sylvian lipomas. As far as we have learned in an extensive review of the literature, there have been nine reports on intracranial lipomas in the sylvian fissure; as for sylvian lipomas which were detected on a CT scan during life, there have been only six cases other than the present one. (author)

Methods for monitoring land subsidence and earth fissures in the Western USA

Directory of Open Access Journals (Sweden)

K. C. Fergason

2015-11-01

Full Text Available Depletion of groundwater resources in many deep alluvial basin aquifers in the Western USA is causing land subsidence, as it does in many regions worldwide. Land subsidence can severely and adversely impact infrastructure by changing the ground elevation, ground slope (grade and through the development of ground cracks known as earth fissures that can erode into large gullies. Earth fissures have the potential to compromise the foundations of dams, levees, and other infrastructure and cause failure. Subsequent to an evaluation of the overall subsidence experienced in the vicinity of subsidence-impacted infrastructure, a detailed investigation to search for earth fissures, and design and/or mitigation of potentially effected infrastructure, a focused monitoring system should be designed and implemented. Its purpose is to provide data, and ultimately knowledge, to reduce the potential adverse impacts of land subsidence and earth fissure development to the pertinent infrastructure. This risk reduction is realized by quantifying the rate and distribution of ground deformation, and to detect ground rupture if it occurs, in the vicinity of the infrastructure. The authors have successfully designed and implemented monitoring systems capable of quantifying rates and distributions of ground subsidence and detection of ground rupture at multiple locations throughout the Western USA for several types of infrastructure including dams, levees, channels, basins, roadways, and mining facilities. Effective subsidence and earth fissure monitoring requires understanding and quantification of historic subsidence, estimation of potential future subsidence, delineation of the risk for earth fissures that could impact infrastructure, and motivation and resources to continue monitoring through time. A successful monitoring system provides the means to measure ground deformation, grade changes, displacement, and anticipate and assess the potential for earth fissuring

Interlobar fissures involvement by lung cancer. Evaluation with thin-section computed tomography images

International Nuclear Information System (INIS)

Kato, Yuji; Yamada, Kouzo; Nomura, Ikuo; Noda, Kazumasa; Ishiwa, Naoki; Maehara, Takamitsu; Kameda, Youichi

1998-01-01

Pleural involvement of interlobar fissure by a tumor is one of the most important factors in the clinical diagnosis of lung cancer. A positive finding of incomplete interlobar fissure of the lung influences not only the surgical procedure but also the prognosis. The aim of this retrospective study was to investigate the usefulness of thin-section computed tomography (CT) compared with conventional CT in the detection of pleural invasion of the interlobar fissure by lung cancer or incomplete interlobar fissure, and the results of surgery, according to the involvement of the pleural surface. We reviewed 90 patients whose tumors were adjacent to the interlobar fissure of the lung through conventional CT scans and subsequent thoracotomy. A comparison of diagnoses based on the findings of thin-section CT and pathologic examination showed that thin-section CT was 94% accurate for pleural invasion of the interlobar fissure, and 100% for incomplete interlobar fissure. Conventional CT, however, was only 63% accurate for pleural invasion of the interlobar fissure and 31% for incomplete interlobar fissure. This leads us to conclude that thin-section CT is helpful in the accurate evaluation of pleural invasion of the interlobar fissure and in the findings of incomplete interlobar fissure in lung cancer for patients in whom tumors are adjacent to the interlobar fissure on conventional CT findings. (author)

Horizontal fissure on neonatal plain chest radiographs: clinical implications

International Nuclear Information System (INIS)

Konarzewska, J.; Zawadzka-Kepczynska, A.; Bianek-Bodzak, A.; Kawinska-Kilianczyk, A.; Domzalska-Popadiuk, I.

2005-01-01

Regardless of etiology, pleural fluid, even in small amounts, can be visualized on the neonatal chest x-ray picture within pulmonary fissures. It remains unclear whether a marked horizontal fissure unaccompanied by any other radiological symptoms is of diagnostic value or not. Ninety-one consecutive neonatal chest radiographs with marked horizontal fissure were retrospectively analyzed. The images were made between 1999 and 2005 on 69 newborns admitted to the Neonatology Department, Institute of Obstetrics and Gynecology, Medical University of Gdansk. Analysis of the radiographs was conducted independently by three radiologists based on the following criteria: fissure thickness (marked or thickened), bronchovascular markings (increased or normal), size and shape of the heart (normal or abnormal), presence or absence of pulmonary infiltration, atelectasis, and changes related to wet lung syndrome. Due to divergent interpretations, the ultimate interpretation was established by consensus in 25 cases. The radiological findings were compared with clinical data. The compatibility of the three independent interpreters was statistically significant (p<0.0001). Marked transverse fissure was the only radiological finding on 66 x-rays. In 63 cases (69.2%) the children were asymptomatic as well. In 3 cases (3.3%) clinical symptoms of respiratory tract infection occurred. On the other 25 images, horizontal fissure was accompanied by other radiological symptoms. Chest x-ray results corresponded with clinical symptoms in 24 cases (26.4%). One child (1.1%) with radiological evidence of wet lung syndrome did not present any typical clinical symptoms of it. Horizontal fissure noted on a neonatal chest x-ray seems to be of minor diagnostic value if not accompanied by any other radiological symptoms. (author)

Cell Behaviors during Closure of the Choroid Fissure in the Developing Eye

Directory of Open Access Journals (Sweden)

Gaia Gestri

2018-02-01

Full Text Available Coloboma is a defect in the morphogenesis of the eye that is a consequence of failure of choroid fissure fusion. It is among the most common congenital defects in humans and can significantly impact vision. However, very little is known about the cellular mechanisms that regulate choroid fissure closure. Using high-resolution confocal imaging of the zebrafish optic cup, we find that apico-basal polarity is re-modeled in cells lining the fissure in proximal to distal and inner to outer gradients during fusion. This process is accompanied by cell proliferation, displacement of vasculature, and contact between cells lining the choroid fissure and periocular mesenchyme (POM. To investigate the role of POM cells in closure of the fissure, we transplanted optic vesicles onto the yolk, allowing them to develop in a situation where they are depleted of POM. The choroid fissure forms normally in ectopic eyes but fusion fails in this condition, despite timely apposition of the nasal and temporal lips of the retina. This study resolves some of the cell behaviors underlying choroid fissure fusion and supports a role for POM in choroid fissure fusion.

Research of compression strength of fissured rock mass

Directory of Open Access Journals (Sweden)

А. Г. Протосеня

2017-03-01

Full Text Available The article examines a method of forecasting strength properties and their scale effect in fissured rock mass using computational modelling with final elements method in ABAQUS software. It shows advantages of this approach for solving tasks of determining mechanical properties of fissured rock mass, main stages of creating computational geomechanic model of rock mass and conducting a numerical experiment. The article presents connections between deformation during loading of numerical model, inclination angle of main fracture system from uniaxial and biaxial compression strength value, size of the sample of fissured rock mass and biaxial compression strength value under conditions of apatite-nepheline rock deposit at Plateau Rasvumchorr OAO «Apatit» in Kirovsky region of Murmanskaya oblast. We have conducted computational modelling of rock mass blocks testing in discontinuities based on real experiment using non-linear shear strength criterion of Barton – Bandis and compared results of computational experiments with data from field studies and laboratory tests. The calculation results have a high-quality match to laboratory results when testing fissured rock mass samples.

Modeling of earth fissures caused by land subsidence due to groundwater withdrawal

Directory of Open Access Journals (Sweden)

B. B. Panda

2015-11-01

Full Text Available Land subsidence and earth fissures are phenomena related to groundwater withdrawal in a sedimentary basin. If the rock basement or basin lithology is irregular, both vertical and horizontal displacements can be induced due to differential settlement and tensile stresses appearing in the soil mass. If the differential settlement is of sufficient magnitude, earth fissuring can occur within tensile zones. The magnitudes of compaction and fissure geometry are closely related to the thickness and skeletal compressibility of fine-grained sediments within the aquifer system. Land subsidence and earth fissuring were modeled by employing a two-dimensional (2-D coupled seepage and stress-strain finite element analysis. The basin bedrock geometry, lithological variation, measurements of surface displacements, and changes in hydraulic head were the critical input parameter for the subsidence modeling. Simulation results indicate that strain had exceeded the approximate threshold for fissure formation of 0.02 to 0.06 % in the area of the identified fissures. The numerical model was used to predict future subsidence and potential earth fissures for flood control structures within the metro Phoenix area.

Fissure fillings from Gideaa, central Sweden

International Nuclear Information System (INIS)

Tullborg, E.L.; Larsson, S.Aa.

1983-08-01

The most frequent fissure filling minerals at Gideaa are calcite, chlorite, pyrite, laumontite, stilbite, smectite, quartz and epidote. Potentially young minerals, i.e. minerals which can be formed during present conditions, are smectite, calcite and quartz, Equilibrium calculations show that these minerals can be stable in the water analysed from Gideaa. In borehole Gi 2, the water exhibits a greater equilibrium with existing minerals in the fissures than water from Gi 4. This is due to the recharge of the water in Gi 4 and discharge of the water in Gi 2. When carbonate saturated water penetrated through the bedrock, calcite precipitated within the more superficial portions of the rock. However, both calcite and zeolite fissures fillings are associated with certain zones in the drill holes. A large number of fractures can be concluded to be of post-Jotnian age. Stilbite, calcite and smectite are associated with these fractures. Laumontite can also be assumed to belong here. The dolerites in the area exhibit a high fracture frequency but a relatively low hydraulic conductivity. This is due to the fact that smectite is very prevalent in the dolerite fractures, Several generations of fracturefilling minerals (above all calcite) have been found in a single fracture. Stable isotope analyses of fissure filling calcites indicate that there are three different groups of calcite. Most of the calcites could not have been precipitated from water of present-day isotope composition at Gideaa, whereas recent calcite may be found in one of the groups. Another group of calcite was precipitated during hydro-thermal conditions.(author)

Experimental study of strontium sorption on fissure filling material

Energy Technology Data Exchange (ETDEWEB)

Eriksen, T E; Cui, Daqing [Royal Institute of Technology, Stockholm (Sweden). Dept. of Chemistry

1994-12-01

We have carried out a comparative study of sorption and desorption of strontium in groundwater on separated magnetic and size fractions of fissure filling material taken from natural fissures in granitic rock. Complete reversibility of the sorption process was demonstrated by identical Freundlich isotherms, isotopic exchangeability and pH dependence of the distribution coefficients Rd. The sorption was found to be strongly pH dependent in the range 3-11. The pH effect can be accommodated in the sorption model by considering the surface areas and surface charges of the minerals in the fissure filling material. 20 refs, 9 figs, 3 tabs.

Experimental study of strontium sorption on fissure filling material

International Nuclear Information System (INIS)

Eriksen, T.E.; Cui, Daqing

1994-12-01

We have carried out a comparative study of sorption and desorption of strontium in groundwater on separated magnetic and size fractions of fissure filling material taken from natural fissures in granitic rock. Complete reversibility of the sorption process was demonstrated by identical Freundlich isotherms, isotopic exchangeability and pH dependence of the distribution coefficients Rd. The sorption was found to be strongly pH dependent in the range 3-11. The pH effect can be accommodated in the sorption model by considering the surface areas and surface charges of the minerals in the fissure filling material. 20 refs, 9 figs, 3 tabs

Pressure suppression pool hydrodynamic studies for horizontal vent exit of Indian PHWR containment

International Nuclear Information System (INIS)

Mohan, N.; Bajaj, S.S.; Saha, P.

1994-01-01

The standard Indian PHWR incorporates a pressure suppression type of containment system with a suppression pool.The design of KAPS (Kakrapar Atomic Power Station) suppression pool system adopts a modified system of downcomers having horizontal vents as compared to vertical vents of NAPS (Narora Atomic Power Station). Hydrodynamic studies for vertical vents have been reported earlier. This paper presents hydrodynamic studies for horizontal type vent system during LOCA. These studies include the phenomenon of vent clearing (where the water slug standing in downcomer initially is injected to wetwell due to rapid pressurization of drywell) followed by pool swell (elevation of pool water due to formation of bubbles due to air mass entering pool at the exit of horizontal vents from drywell). The analysis performed for vent clearing and pool swell is based on rigorous thermal hydraulic calculation consisting of conservation of air-steam mixture mass, momentum and thermal energy and mass of air. Horizontal vent of downcomer is modelled in such a way that during steam-air flow, variation of flow area due to oscillating water surface in downcomer could be considered. Calculation predicts that the vent gets cleared in about 1.0 second and the corresponding downward slug velocity in the downcomer is 4.61 m/sec. The maximum pool swell for a conservative lateral expansion is calculated to be 0.56 m. (author). 3 refs., 12 figs

Analysis of the implementation of a sand bed type filter for the venting of a nuclear power plant

International Nuclear Information System (INIS)

Cuevas V, D.; Sainz M, E.; Ortiz V, J.

2017-09-01

The filtered venting of the containment has been adopted in European countries to mitigate the consequences derived from the excess pressure of the containment during a severe accident. When venting has taken place, the fission products are released directly into the environment, unless a filter is placed in the path of the same, so various types of filters are used to trap the fission products. The containment venting filters currently installed use different filtering technologies that involve more than one medium. Those who use water as the first stage of filtration are called wet systems, are equipped with additional stages to eliminate water drops and emissions of fine aerosols, and may even be equipped with an element that contains certain means of absorption for the gaseous iodine species filtration. Other designs, based on deep bed filtration as the main retention stage, called dry filters; use metal fiber, ceramic or sand filtration media to trap aerosols. The present work evaluates the hydraulic characteristics of the sand bed type filter designed by EDF as a candidate to be installed in the containment of the BWR Mark II (primary containment type of the Laguna Verde nuclear power plant). The evaluation of the sand bed filter was performed using the OpenFOAM open source software package. Models of each zone of the filtering device were generated and by means of a series of parametric calculations of computational fluid mechanics, the relevant hydrodynamic characteristics of the device were obtained, such as pressure drops against mass flow and pressure fields and velocity under different operating conditions. On the other hand, the validation of the sand bed filter model was made when comparing the results of experimental tests carried out in a sand column of the PITEAS program (1985-1986) against the simulation in OpenFOAM. The results obtained are very close to those obtained experimentally. (Author)

On Small Disturbance Ascent Vent Behavior

Science.gov (United States)

Woronowicz, Michael

2015-01-01

As a spacecraft undergoes ascent in a launch vehicle, its ambient pressure environment transitions from one atmosphere to high vacuum in a matter of a few minutes. Venting of internal cavities is necessary to prevent the buildup of pressure differentials across cavity walls. These pressure differentials are often restricted to low levels to prevent violation of container integrity. Such vents usually consist of fixed orifices, ducts, or combinations of both. Duct conductance behavior is fundamentally different from that for orifices in pressure driven flows governing the launch vehicle ascent depressurization environment. Duct conductance is governed by the average pressure across its length, while orifice conductance is dictated by a pressure ratio. Hence, one cannot define a valid equivalent orifice for a given duct across a range of pressure levels. This presentation discusses development of expressions for these two types of vent elements in the limit of small pressure differentials, explores conditions for their validity, and compares their features regarding ascent depressurization performance.

Vision in hydrothermal vent shrimp.

OpenAIRE

Chamberlain, S C

2000-01-01

Bresiliid shrimp from hydrothermal vents on the Mid-Atlantic Ridge have non-imaging eyes adapted for photodetection in light environments of very low intensity. Comparison of retinal structures between both vent shrimp and surface-dwelling shrimp with imaging eyes, and between juvenile and adult vent shrimp, suggests that vent shrimp have evolved from ancestors that lived in a light environment with bright cyclic lighting. Whether the vent shrimp live in swarms and have large dorsal eyes or l...

Diagnostic problems in the identification of fissures (incomplete fractures) in horses

International Nuclear Information System (INIS)

Huskamp, B.; Stadtbaeumer, G.; Mengeler, U.; Nowak, M.

1994-01-01

Diagnosing bone-fissures as part of examinations of lameness often confronts the examining veterinarian with problems, which can end on being forensic matters. A fissure which is an incomplete fracture, whereby the division of the continuity ends in healthy bone tissue may in some cases initially not be shown radiologically. Initially strong superior-lameness combined with part sensitivity of pressure are apparent in the area of the line of fissure without soft-tissue swelling. Depending on the localisation of the fracture minor lameness can be apparent. If a fissure has initially been diagnosed, it is necessary to examine the affected limb radiologically from at least two projections appealing the corresponding date for exposure. If the initial diagnosis can not be confirmed radiologically, diagnostic anaesthesia is permitted in exceptional cases. If there is any doubt about the result, the affected limb must be held at rest until the possibility of a fissure can be excluded. The owner of the horse must be informed about problems of diagnostics and their risks [de

The Use of Pit and Fissure Sealants—A Literature Review

Directory of Open Access Journals (Sweden)

Reem Naaman

2017-12-01

Full Text Available This paper reviews the literature and discusses the latest updates on the use of pit and fissure sealants. It demonstrates the effectiveness of pit and fissure sealants in preventing caries and the management of early carious lesions. It compares the use of different sealant materials and their indications. It describes the application technique for sealants. It also reviews the cost-effectiveness of sealants as a preventive strategy. From this review and after the discussion of recently published studies on pit and fissure sealants, it is evident that sealants are effective in caries prevention and in preventing the progression of incipient lesions. It is therefore recommended that pit and fissure sealant be applied to high-caries-risk children for optimum cost-effectiveness. It is a highly sensitive technique that needs optimum isolation, cleaning of the tooth surface, etching, and the application of a thin bonding layer for maximum benefit. Recall and repair, when needed, are important to maximize the effectiveness of such sealant use.

The Use of Pit and Fissure Sealants—A Literature Review

Science.gov (United States)

Naaman, Reem; El-Housseiny, Azza A.; Alamoudi, Najlaa

2017-01-01

This paper reviews the literature and discusses the latest updates on the use of pit and fissure sealants. It demonstrates the effectiveness of pit and fissure sealants in preventing caries and the management of early carious lesions. It compares the use of different sealant materials and their indications. It describes the application technique for sealants. It also reviews the cost-effectiveness of sealants as a preventive strategy. From this review and after the discussion of recently published studies on pit and fissure sealants, it is evident that sealants are effective in caries prevention and in preventing the progression of incipient lesions. It is therefore recommended that pit and fissure sealant be applied to high-caries-risk children for optimum cost-effectiveness. It is a highly sensitive technique that needs optimum isolation, cleaning of the tooth surface, etching, and the application of a thin bonding layer for maximum benefit. Recall and repair, when needed, are important to maximize the effectiveness of such sealant use. PMID:29563440

Preferential flow in fissured sediments in desert soils related to radioactive waste disposal

International Nuclear Information System (INIS)

Scanlon, B.R.; Raney, J.A.

1992-01-01

Unsaturated flow in fissured sediments in the Chihuahuan Desert of Texas was examined to determine if these features act as preferred pathways for water and solute transport. Fissures are surface features, or gulleys, that are underlain by fractures filled with sediment derived from surrounding areas. Hydraulic and chemical approaches were used to investigate unsaturated flow processes beneath and adjacent to fissures, and the results were compared with data from surrounding geomorphic systems such as arroyos, ephemeral streams, and interstreams. Typically, high water potentials in surficial sediments result from infiltration of recent precipitation. Below this surficial zone of high water potentials lies a zone of low water potentials that is much thinner beneath the fissure than in adjacent sediments or in sediments beneath ephemeral streams and interstreams. Maximum chloride concentrations in profiles in the near-surface fissured sediments were much lower than those measured in all other geomorphic systems. The corresponding moisture velocities in the fissured sediments ranged from 10 to 70 mm/yr. A tracer experiment demonstrated higher downward water and solute transport in the fracture fill beneath the fissure relative to adjacent sediments. Numerical simulations of the tracer experiment with the computer code TRACR3D reproduced the overall shape of the tracer plume. Sensitivity analyses demonstrated that the tracer plume is most sensitive to spatial variability in soil texture and the corresponding hydraulic parameters. The results from this study suggest that sediments in the fissured area act as preferred pathways in the shallow subsurface because surface runoff is concentrated in the fissures and because underlying fractures and cavities provide avenues for moisture and solute transport

Recent Advances in the Pharmacotherapy of Chronic Anal Fissure: An Update

Directory of Open Access Journals (Sweden)

Bikash Medhi

2008-07-01

Full Text Available Surgical sphincterotomy reduces anal tone and sphincter spasm and promotes ulcer healing. Because the surgery is associated with the side effect of faecal incontinence, pharmacological agents to treat chronic anal fissure have been explored recently. Glyceryl trinitrate (GTN ointment (0.2% has an efficacy of up to 68% in healing chronic anal fissure, but it is associated with headache as the major and most common side effect. Though botulinum toxin injected into the anal sphincter healed over 80% of chronic anal fis-sures, it is more invasive and expensive than GTN therapy. Diltiazem ointment achieved healing of chronic anal fissure comparable to 0.2% GTN ointment but was associated with fewer side effects. Other drugs that have been tried are lidocaine, the alpha-adrenergic antagonist indoramin, and the potassium channel opener minoxidil.

Filtered atmospheric venting of light water reactor containments

International Nuclear Information System (INIS)

Hedgran, A.; Ahlstroem, P.E.; Nilsson, L.; Persson, Aa.

1982-11-01

The aim of filtered venting is to improve the function of the reactor containment in connection with very severe accidents. By equipping the containment with a safety valve for pressure relief and allowing the released gases to pass through an effective filter, it should be possible to achieve a considerable protective effect. The work has involved detailed studies of the core meltdown sequence, how the molten core material runs out of the reactor vessel, what effect it has on concrete and other structures and how final cooling of the molten core material takes place. On the basis of previous Swedish studies, the project has chosen to study a filter concept that consists of a gravel bed of large volume. This filter plant shall not only retain the radioactive particles that escape from the containment through the vent line, but shall also condense the accompanying steam. After the government decided in 1981 that Barsebaeck was to be equipped with filtered venting and issued specifications regarding its performance, the project aimed at obtaining results that could be used to design and verify a plant for filtered venting at the Barsebaeck nuclear power station. As far as the other Swedish nuclear power plants at Oskarshamn, Ringhals and Forsmark are concerned, the results are only applicable to a limited extent. Additional studies are required for these nuclear power plants before the value of filtered venting can be assessed. Based on the results of experiments and analyses, the project has made a safety analysis with Barsebaeck as a reference plant in order to study how the introduction of filtered venting affects the safety level at a station. In summary, the venting function appears to entail a not insignificant reduction of risks for boiling water reactors of the Barsebaeck type. For a number of types of such very severe core accident cases, the filter design studied ensures a substantial reduction of the releases. However it has not been possible within the

Penetration of fluoride-containing self-gelling liquids into human molar occlusal fissures in vitro.

Science.gov (United States)

Bottenberg, P; Slop, D; Coomans, D

1989-01-01

In this in vitro study the ability and speed of self-gelling liquid compositions to penetrate into fissures were evaluated. Two formulations containing either tetraethylsilicate, ammonium fluoride, and sodium lauryl sulfate or tetraethylsilicate, sodium fluoride, and cetylpyridinium chloride at different concentrations were used. It is shown that fissure penetration occurs when a certain minimum content of surface-active agent is present. Fissure penetration is achieved within 3-4 s, according to the fissure morphology.

Explosive Volcanic Eruptions from Linear Vents on Earth, Venus and Mars: Comparisons with Circular Vent Eruptions

Science.gov (United States)

Glaze, Lori S.; Baloga, Stephen M.; Wimert, Jesse

2010-01-01

Conditions required to support buoyant convective plumes are investigated for explosive volcanic eruptions from circular and linear vents on Earth, Venus, and Mars. Vent geometry (linear versus circular) plays a significant role in the ability of an explosive eruption to sustain a buoyant plume. On Earth, linear and circular vent eruptions are both capable of driving buoyant plumes to equivalent maximum rise heights, however, linear vent plumes are more sensitive to vent size. For analogous mass eruption rates, linear vent plumes surpass circular vent plumes in entrainment efficiency approximately when L(sub o) > 3r(sub o) owing to the larger entrainment area relative to the control volume. Relative to circular vents, linear vents on Venus favor column collapse and the formation of pyroclastic flows because the range of conditions required to establish and sustain buoyancy is narrow. When buoyancy can be sustained, however, maximum plume heights exceed those from circular vents. For current atmospheric conditions on Mars, linear vent eruptions are capable of injecting volcanic material slightly higher than analogous circular vent eruptions. However, both geometries are more likely to produce pyroclastic fountains, as opposed to convective plumes, owing to the low density atmosphere. Due to the atmospheric density profile and water content on Earth, explosive eruptions enjoy favorable conditions for producing sustained buoyant columns, while pyroclastic flows would be relatively more prevalent on Venus and Mars. These results have implications for the injection and dispersal of particulates into the planetary atmosphere and the ability to interpret the geologic record of planetary volcanism.

Understanding vented gas explosions

Energy Technology Data Exchange (ETDEWEB)

Lautkaski, R. [VTT Energy, Espoo (Finland). Energy Systems

1997-12-31

The report is an introduction to vented gas explosions for nonspecialists, particularly designers of plants for flammable gases and liquids. The phenomena leading to pressure generation in vented gas explosions in empty and congested rooms are reviewed. The four peak model of vented gas explosions is presented with simple methods to predict the values of the individual peaks. Experimental data on the external explosion of dust and gas explosions is discussed. The empirical equation relating the internal and external peak pressures in vented dust explosions is shown to be valid for gas explosion tests in 30 m{sup 3} and 550 m{sup 3} chambers. However, the difficulty of predicting the internal peak pressure in large chambers remains. Methods of explosion relief panel design and principles of vent and equipment layout to reduce explosion overpressures are reviewed. (orig.) 65 refs.

Understanding vented gas explosions

Energy Technology Data Exchange (ETDEWEB)

Lautkaski, R [VTT Energy, Espoo (Finland). Energy Systems

1998-12-31

The report is an introduction to vented gas explosions for nonspecialists, particularly designers of plants for flammable gases and liquids. The phenomena leading to pressure generation in vented gas explosions in empty and congested rooms are reviewed. The four peak model of vented gas explosions is presented with simple methods to predict the values of the individual peaks. Experimental data on the external explosion of dust and gas explosions is discussed. The empirical equation relating the internal and external peak pressures in vented dust explosions is shown to be valid for gas explosion tests in 30 m{sup 3} and 550 m{sup 3} chambers. However, the difficulty of predicting the internal peak pressure in large chambers remains. Methods of explosion relief panel design and principles of vent and equipment layout to reduce explosion overpressures are reviewed. (orig.) 65 refs.

PERBEDAAN TOPICAL FLUORIDE APPLICATION DAN FISSURE SEALANT DALAM MENCEGAH KARIES PADAGIGI MOLAR SATU

Directory of Open Access Journals (Sweden)

Pawarti Pawarti

2017-07-01

Full Text Available Abstract: Topical Fluoride Application And Fissure Sealant To Prevent Dental Caries Permanent First Molars. Anatomy pits and fissures of teeth are caries initiation vulnerable areas of the permanent molars that grow at the age of 6 years where children can not perform oral hygiene. Caries prevention can be done by closing the pits and fissures or application of fluoride (topical fluoride application on the surface of the teeth. The purpose of this study was to analyze the difference fissure sealants and topical application of fluoride to prevent dental caries of first permanent molars. This study was a quasi-experimental study with time series, a sample was taken by purposive 117-second grade students of SDN District of North Pontianak. Data were analyzed using t-test. The result showed that fissure sealant more effective in caries prevention of first permanent molar than topical fluoride application where there were none caries teeth after and month fissure sealant, 25% sealant partially off and 11% fully off. Teeth that have done fluoride after 6 months of 3.9% of dental caries, the eighth month of 5.4% of dental caries. There was a significant difference between the effectiveness of fissure sealants with topical application of fluoride to prevent dental caries in first permanent molars p-value < 0.05, after 6-month p-value: 0.004 and after 8-month p-value: 0.001. Abstrak: Topical Fluoride Application Dan Fissure Sealant Untuk Mencegah Karies Pada Gigi Molar Satu Permanen. Anatomi pit dan fisura gigi merupakan daerah rentan inisiasi karies gigi molar satu permanen yang tumbuh pada usia 6 tahun anak belum bisa melakukan kebersihan mulutnya. Pencegahan karies dapat dilakukan dengan cara menutup pit dan fissure atau pengolesan fluor (topical fluoride application pada permukaan gigi. Tujuan penelitian ini untuk menganalisis perbedaan efektivitas fissure sealant dan topical fluoride application untuk mencegah karies gigi molar satu permanen anak

[Application of individually designed trans-fissure approach in brain surgery: analysis of 90 cases].

Science.gov (United States)

Zhao, Ji-Zong; Wang, Shuo; Zhang, Mao-Zhi; Wang, Lei; Wang, Rong; Tang, Ya-Juan

2009-01-06

To explore the feasibility and value of trans-fissure approaches in brain surgery through individually designed craniotomy. Ninety patients with intracranial space-occupying lesions, 47 males and 58 females, aged (43 +/- 14) (1 - 68), were treated by individualized trans-fissure approach surgeries. Linear scalp incision or "horseshoe shape" scalp incision were designed to perform the operation, with a bone flap 3 - 4 cm in diameter. The shortest approach to reach the lesion was decided under the guidance of neuro-navigation and real-time B-mode ultrasonography. Then the lesions were removed through natural cortical fissures. Another 79 patients with intracranial space-occupying lesions, 53 males and 51 females, aged (42 +/- 11) (15 -73), undergoing classical surgeries in the same period were used as control group. The average operation time, size of bone flap, amount of blood loss, hospitalization time, and hospitalization cost were compared between these 2 groups. The operation time of the individually designed trans-fissure approach group was (3.1 +/- 1.6) hours (1.33 - 10.83 hours), significantly shorter than that of the control group [(4.8 +/- 1.9) hrs, P trans-fissure approach group was (173 +/- 168) ml (20 m - 500 ml), significantly less than that of the control group [(410 +/- 61) ml, P trans-fissure approach group was (12 +/- 5) cm2 [(1 - 25) cm2], significantly smaller than that of the control group [(20. +/- 9) cm2, P trans-fissure approach group received retransfusion, compared to 15 in the control group, during operation. No infection or other significant complications occurred after operation in the individually designed trans-fissure approach group. The hospitalization time of the individually designed trans-fissure approach group was (20 +/- 6) days (9 - 39 days), significantly shorter than that of the control group [(24 +/- 7) days, P trans-fissure approach group was (23171 +/- 7280) yuan RMB; significantly lower than that of the control group

Demonstration of the pulmonary interlobar fissures on multiplanar reformatted images with 64-slices spiral CT

International Nuclear Information System (INIS)

Wang Yafei; Chen Yerong; Shan Xiuhong; Tang Zhiyang; Ni Enzhen; Huang Hao; Wu Shuchun

2009-01-01

Objective: To determine the optimal orientation and slice thickness of reformatted images to visualize the interlobar fissures on multiplanar reformation (MPR) images and to recommend MPR imaging protocal for visualizing interlobar fissures in clinical practise. Methods: 64-slices CT scans of chest were obtained in 300 patients without pulmonary diseases. Axial, sagittal and coronal images were reformatted at 1, 2, 3, 7 mm slice thickness respectively from the raw volume data. Three experienced radiologists evaluated all of the MPR images in the lung window and compared the differences in visualization of the interlohar fissures among the three reformatted orientations and at the different slice thicknesses with Fisher test and Friedman test. Results: Fissures on sagittal MPR images using 1, 2, 3, and 7 mm reformatted slice thickness appeared as a fine line and the preference value analysis showed the MPR images with a 3 mm reformatted slice thickness is the best for visualizing the interlobar fissure. Compared to the sagittal orientation, the coronal was not as good and the axial was the worst among the three orientations. The coronal images with a 3 mm reformatted slice thickness were slightly inferior to sagittal images. The right horizontal fissures were observed as a fine line in all coronal image in 94.0% (282)of cases and in some of the images in 6.0% (18) of cases, the right oblique fissures were displayed as a fine line in coronal images in 2.3% (7) of cases and in some images in 85.0% (255) of cases, the left oblique fissures were displayed as a fine line in some coronal images in 35.7% (107) of cases and displayed as a coarse line in 64.3% (193) of cases. On axial MPR images using 3 mm reformation slice thickness, the right oblique fissures and the left oblique fissures were displayed as a fine line in some axial images in 79.3% (238) and 81.0% (243) of cases respectively, none of the images showed horizontal fissures as a fine line. There was

Filtered atmospheric venting of LWR containments

International Nuclear Information System (INIS)

Hoegberg, L.; Ahlstroem, P.E.; Bachofner, E.; Graeslund, C.; Johansson, K.; Nilsson, L.; Persson, Aa.; Eriksson, B.

1981-03-01

The FILTRA project is a cooperative Swedish programme which started in February 1980. It is aimed at investigating the possibility of reducing the risk for a large release of radioactivity, assuming a severe reactor accident. The project has been focused on filtered venting of the reactor containment. The first stage of the project has dealt with two types of severe accident sequences, namely core meltdown as a result of the complete loss of water supplies to the reactor pressure vessel and insufficient cooling of the reactor containment. Some important conclusion are the following. The applicability of computer models used to describe various phenomena in the accident sequence must be scrutinized. The details of the design of the containment are important and must be taken into consideration in a more accurate manner than in previous analyses. A pressure relief area of less than 1 m 2 appears to be adequate. The following principles should guide the technical design of filtered venting systems, namely reduction of the risk for the release of those radioactive substances which could cause long term land contamination, provision for a passive function of the vent filter system during the first 24 hours and achievement of filtering capabilities which make leakages in severe accidents comparable to the leakages of radioactive substances in less severe accidents, which do not necessarily actuate the pressure relief system. Nothing indicates that a system for filtered venting of a BWR containment would have a significant negative effect on the safety within the framework of the design basis. Efforts should be directed towards designing a filtered venting system for a BWR such as Barsebaeck. (authors)

Hemorrhoids and anal fissures in inflammatory bowel disease.

Science.gov (United States)

D'Ugo, S; Stasi, E; Gaspari, A L; Sileri, P

2015-12-01

Perianal disease is a common complication of inflammatory bowel disease (IBD). It includes different conditions from more severe and potentially disabling ones, such as abscesses and fistulas, to more benign conditions such as hemorrhoids, skin tags and fissures. Most literature has been focused on anal sepsis and fistulae, as they carry the majority of disease burden and often alter the natural course of the disease. Hemorrhoids and anal fissures in patients with IBD have been overlooked, although they can represent a challenging problem. The management of hemorrhoids and fissures in IBD patients may be difficult and may significantly differ compared to the non-affected population. Historically surgery was firmly obstructed, and hemorrhoidectomy or sphincterotomy in patients with associated diagnosis of IBD was considered harmful, although literature data is scant and based on small series. Various authors reported an incidence of postoperative complications higher in IBD than in the general populations, with potential severe events. Considering that a spontaneous healing is possible, the first line management should be a medical therapy. In patients non-responding to conservative measures it is possible a judicious choice of surgical options on a highly selective basis; this can lead to acceptable results, but the risk of possible complications needs to be considered. In this review it is analyzed the current literature on the incidence, symptoms and treatment options of hemorrhoids and anal fissures in patients with Crohn's disease and ulcerative colitis.

Short linear shadows connecting pulmonary segmental arteries to oblique fissures in volumetric thin-section CT images: comparing CT, micro-CT and histopathology

International Nuclear Information System (INIS)

Guan, Chun-Shuang; Ma, Da-Qing; Chen, Jiang-Hong; Chen, Bu-Dong; Cui, Dun; Zhang, Yan-Song; Liu, Wei-Hua

2016-01-01

To retrospectively evaluate short linear shadows connecting pulmonary segmental arteries to oblique fissures in thin-section CT images and determine their anatomical basis. CT scanning was performed on 108 patients and 11 lung specimens with no lung diseases around the oblique fissures or hilar. Two radiologists evaluated the imaging. The parameters included length, thickness of short linear shadows, pulmonary segmental artery variations, and traction interlobar fissures, etc. The short linear shadows were not related to sex, age, or smoking history. The lengths of the short linear shadows were generally within 10 mm. The thicknesses of the short linear shadows ranged from 1 to 2 mm. Of the patients, 26.9 % showed pulmonary segmental artery variations; 66.7 % of short linear shadows pulled oblique fissures. In three-dimensional images, the short linear shadows appeared as arc planes, with one side edge connected to the oblique fissure, one side edge connected to a pulmonary segmental artery. On the tissue slices, the short linear shadow exhibited a band structure composed of connective tissues, small blood vessels, and small lymphatic vessels. Short linear shadows are a type of normal intrapulmonary membranes and can maintain the integrity of the oblique fissures and hilar structure. (orig.)

Orientation of the eruption fissures controlled by a shallow magma chamber in Miyakejima

Directory of Open Access Journals (Sweden)

Nobuo Geshi

2016-11-01

Full Text Available Orientation of the eruption fissures and composition of the lavas of the Miyakejima volcano indicate tectonic influence of a shallow magma chamber on the distribution of eruption fissures. We examined the distributions and magmatic compositions of 23 fissures that formed within the last 2800 years, based on a field survey and a new dataset of 14C ages. The dominant orientation of the eruption fissures in the central portion of the volcano was found to be NE-SW, which is perpendicular to the direction of regional maximum horizontal compressive stress (σHmax. Magmas that show evidences of magma mixing between basaltic and andesitic magmas erupted mainly from the eruption fissures with a higher offset angle from the regional σHmax direction. The presence of a shallow dike-shaped magma chamber controls the distribution of the eruption fissures. The injection of basaltic magma into the shallow andesitic magma chamber caused the temporal rise of internal magmatic pressure in the shallow magma chamber. Dikes extending from the andesitic magma chamber intrude along the local compressive stress field which is generated by the internal excess pressure of the andesitic magma chamber. As the result, the eruption fissures trend parallel to the elongation direction of the shallow magma chamber. Injection of basaltic magma into the shallow andesitic magma chamber caused the magma mixing. Some basaltic dikes from the deep-seated magma chamber reach the ground surface without intersection with the andesitic magma chamber. The patterns of the eruption fissures can be modified in the future as was observed in the case of the destruction of the shallow magma chamber during the 2000 AD eruption.

Geologic form and setting of a hydrothermal vent field at lat 10°56‧N, East Pacific Rise: A detailed study using Angus and Alvin

Science.gov (United States)

McConachy, T. F.; Ballard, R. D.; Mottl, M. J.; von Herzen, R. P.

1986-04-01

A hydrothermal vent field, here called the Feather Duster site, occurs on the eastern marginal high near the edge of a narrow (95-m) and shallow (15 20-m) axial graben, within an area dominated by sheet flows and collapse features. The sheet flows are intermediate in relative age between younger fluid-flow lavas on the floor of the axial graben and older pillow (constructional) lavas on the marginal highs. Hydrothermal activity occurs in two zones within a 65 by 45 m area. The main zone is located where a fissure system and sulfide-sulfate chimneys vent warm (9 47 °C) and hot (347 °C) hydrothermal fluids. Here, two mounds of massive sulfide totaling about 200 t are forming. One occurs at the base of a 3-m-high scarp which is the wall of a drained lava lake; the other is perched on top of the scarp. *Present address: Department of Geology, University of Toronto, Toronto, Ontario, Canada M5S 1A1

Hydrogen venting characteristics of commercial carbon-composite filters and applications to TRU waste

International Nuclear Information System (INIS)

Callis, E.L.; Marshall, R.S.; Cappis, J.H.

1997-04-01

The generation of hydrogen (by radiolysis) and of other potentially flammable gases in radioactive wastes which are in contact with hydrogenous materials is a source of concern, both from transportation and on-site storage considerations. Because very little experimental data on the generation and accumulation of hydrogen was available in actual waste materials, work was initiated to experimentally determine factors affecting the concentration of hydrogen in the waste containers, such as the hydrogen generation rate, (G-values) and the rate of loss of hydrogen through packaging and commercial filter-vents, including a new design suitable for plastic bags. This report deals only with the venting aspect of the problem. Hydrogen venting characteristics of two types of commercial carbon-composite filter-vents, and two types of PVC bag closures (heat-sealed and twist-and-tape) were measured. Techniques and equipment were developed to permit measurement of the hydrogen concentration in various layers of actual transuranic (TRU) waste packages, both with and without filter-vents. A test barrel was assembled containing known configuration and amounts of TRU wastes. Measurements of the hydrogen in the headspace verified a hydrogen release model developed by Benchmark Environmental Corporation. These data were used to calculate revised wattage Emits for TRU waste packages incorporating the new bag filter-vent

Fissure formation in coke. 2: Effect of heating rate, shrinkage and coke strength

Energy Technology Data Exchange (ETDEWEB)

D.R. Jenkins; M.R. Mahoney [CSIRO, North Ryde, NSW (Australia). Mathematical and Information Sciences

2010-07-15

We investigate the effects of the heating rate, coke shrinkage and coke breakage strength upon the fissure pattern developed in a coke oven charge during carbonisation. This is done principally using a mechanistic model of the formation of fissures, which considers them to be an array of equally spaced fissures, whose depth follows a 'period doubling' pattern based upon the time history of the fissures. The model results are compared with pilot scale coke oven experiments. The results show that the effect of heating rate on the fissure pattern is different to the effect of coke shrinkage, while the effect of coke breakage strength on the pattern is less pronounced. The results can be seen in both the shape and size of resulting coke lumps after stabilisation. The approach gives the opportunity to consider means of controlling the carbonisation process in order to tune the size of the coke lumps produced. 7 refs., 18 figs., 4 tabs.

Differential compaction mechanism for earth fissures near Casa Grande, Arizona.

Science.gov (United States)

Jachens, R.C.; Holzer, T.L.

1982-01-01

Precise gravity measurements indicate that earth fissures or tension cracks caused by ground-water withdrawal within a 10km2 area SE of Casa Grande are associated with relief on the buried interface between the alluvial aquifer and underlying bedrock. These relations suggest that the fissures are forming in response to localized differential compaction caused by localized variations of aquifer-system thickness. -from Authors

Søvind Marl - Behaviour of a plastic fissured Eocene clay

DEFF Research Database (Denmark)

Grønbech, Gitte Lyng

The thesis regards the characterisation and determination of properties of Søvind Marl, a Danish highly fissured and plastic clay. Highly fissured, plastic clays are present at great depths several places in Denmark, where extensive development activity is currently ongoing. Nonetheless...... will determine the correlation factors from field tests to undrained shear strength. Finally, the thesis is concluded with recommendations for further work within the field of plastic clays....

Impact de la preparation des anodes crues et des conditions de cuisson sur la fissuration dans des anodes denses

Science.gov (United States)

Amrani, Salah

classifier les differentes fissurations en plusieurs categories en se basant sur certains criteres tels que le type de fissures (horizontale, verticale et inclinee), leurs localisations longitudinales (bas, milieu et haut de l'anode) et transversales (gauche, centrale et droite). Les effets de la matiere premiere, les parametres de fabrication des anodes crues ainsi que les conditions de cuisson sur la fissuration ont ete etudies. La fissuration des anodes denses en carbones cause un serieux probleme pour l'industrie d'aluminium primaire. La realisation de ce projet a permis la revelation de differents mecanismes de fissuration, la classification de fissuration par plusieurs criteres (position, types localisation) et l'evaluation de l'impact de differents parametres sur la fissuration. Les etudes effectuees dans le domaine de cuisson ont donne la possibilite d'ameliorer l'operation et reduire la fissuration des anodes. Le travail consiste aussi a identifier des techniques capables d'evaluer la qualite d'anodes (l'ultrason, la tomographie et la distribution de la resistivite electrique). La fissuration des anodes en carbone est consideree comme un probleme complexe, car son apparition depend de plusieurs parametres repartis sur toute la chaine de production. Dans ce projet, plusieurs nouvelles etudes ont ete realisees, et elles permettent de donner de l'originalite aux travaux de recherches faits dans le domaine de la fissuration des anodes de carbone pour l'industrie de l'aluminium primaire. Les etudes realisees dans ce projet permettent d'ajouter d'un cote, une valeur scientifique pour mieux comprendre le probleme de fissuration des anodes et d'un autre cote, d'essayer de proposer des methodes qui peuvent reduire ce probleme a l'echelle industrielle.

Numerical simulation of earth fissures caused by overly aquifer exploitation at Guangming Village, China

Science.gov (United States)

Ye, S.; Franceschini, A.; Zhang, Y.; Janna, C.; Gong, X.; Yu, J.; Teatini, P.

2017-12-01

Earth fissures accompanying anthropogenic land subsidence due to overly aquifer exploitation create significant geohazards in China. In the framework of an efficient and safe management of groundwater, numerical models represent a unique scientific approach to predict the generation and development of earth fissures. However, the common geomechanical simulators fail to reproduce fissure development because, due to compatibility conditions, they cannot be effectively applied in discontinuous mechanics. We present an innovative modelling approach for the simulation of fissure development. Firstly, a regional 3D groundwater model is calibrated on available piezometric records; secondly, the regional outcome is used to define the boundary conditions of a local 3D groundwater model developed at the fissure scale and implementing a refined discretization of the local hydrogeologic setting; finally, the pressure change are used as forcing factor in a local 3D geomechanical model, which combines Finite Elements and Interface Elements to simulate the deformation of the continuous aquifer system and the generation and sliding/opening of earth fissures The approach has been applied to simulate the earth fissure at Guangming Village in Wuxi, China with land subsidence of more than 1 m caused by the overexploitation of the second confined aquifer. The first earth fissure was observed in 1998. It developed fast from 1998 to 2007. The domain addressed by the local simulations is 2 km wide and 5 km long. The thickness of the aquifer system ranges from 0 m, in the proximity of a mountain ridge southward, to 210 m northward and includes a phreatic aquifer, the first and second confined aquifers, and four aquitards. The simulations spanned the period from 1980, i.e. before the inception of large groundwater withdrawals, to 2015. The modelling results highlight that the earth fissures at Guangming Village have been caused by tension and shear, which developed from the land surface

Provisions for containment venting in Germany

International Nuclear Information System (INIS)

Wilhelm, J.G.

1997-01-01

In this short paper an overlook is given of the systems developed in Germany for filtered containment venting and their implementation in nuclear power plants. More information on the development can be found in the Proceedings of the DOE/NRC Aircleaning Conferences. In Germany, 28.8 % of the electric energy is produced by 19 nuclear power reactors. No new power reactor is expected to be built at least within the next ten years, but France and Germany cooperate in the development of a future European Power Reactor (ERP). This reactor type will be fitted with a core catcher and passive cooling in order to avoid serious consequences of a hypothetical core meltdown accident so that provisions for containment venting are not required. 3 refs., 6 figs., 1 tab

Provisions for containment venting in Germany

Energy Technology Data Exchange (ETDEWEB)

Wilhelm, J.G.

1997-08-01

In this short paper an overlook is given of the systems developed in Germany for filtered containment venting and their implementation in nuclear power plants. More information on the development can be found in the Proceedings of the DOE/NRC Aircleaning Conferences. In Germany, 28.8 % of the electric energy is produced by 19 nuclear power reactors. No new power reactor is expected to be built at least within the next ten years, but France and Germany cooperate in the development of a future European Power Reactor (ERP). This reactor type will be fitted with a core catcher and passive cooling in order to avoid serious consequences of a hypothetical core meltdown accident so that provisions for containment venting are not required. 3 refs., 6 figs., 1 tab.

Incomplete fissures in severe emphysematous patients evaluated with MDCT: Incidence and interobserver agreement among radiologists and pneumologists

Energy Technology Data Exchange (ETDEWEB)

Koenigkam-Santos, Marcel, E-mail: marcelk46@yahoo.com.br [Department of Diagnostic and Interventional Radiology, University of Heidelberg, Neuenheimer Feld 110, 69120 Heidelberg (Germany); Chest Clinic (Thoraxklinik), University of Heidelberg, Amalienstr. 5,69126 Heidelberg (Germany); Department of Radiology, University Hospital of the School of Medicine of Ribeirao Preto - University of Sao Paulo, Av. Bandeirantes 3900, Campus Universitario Monte Alegre, 14048 900 Ribeirao Preto, SP (Brazil); Puderbach, Michael [Department of Diagnostic and Interventional Radiology, University of Heidelberg, Neuenheimer Feld 110, 69120 Heidelberg (Germany); Chest Clinic (Thoraxklinik), University of Heidelberg, Amalienstr. 5,69126 Heidelberg (Germany); Gompelmann, Daniela; Eberhardt, Ralf; Herth, Felix [Chest Clinic (Thoraxklinik), University of Heidelberg, Amalienstr. 5,69126 Heidelberg (Germany); Kauczor, Hans-Ulrich [Department of Diagnostic and Interventional Radiology, University of Heidelberg, Neuenheimer Feld 110, 69120 Heidelberg (Germany); Heussel, Claus Peter [Department of Diagnostic and Interventional Radiology, University of Heidelberg, Neuenheimer Feld 110, 69120 Heidelberg (Germany); Chest Clinic (Thoraxklinik), University of Heidelberg, Amalienstr. 5,69126 Heidelberg (Germany)

2012-12-15

Objective: Pulmonary fissures completeness predicts efficacy in endobronchial valves (EBV) implantation, a new lobar volume reduction therapy for severe emphysematous patients. We assessed the incidence of incomplete fissures and the interobserver agreement in its evaluation with MDCT, in severe emphysematous patients prior to EBV implantation. Materials and Methods: Volumetric thin-section CT scans of 35 patients (CODP GOLD 3/4, heterogeneous emphysema) were retrospectively reviewed by 2 pneumologists, 1 general and 2 experienced chest radiologists, independently and blinded for treatment outcome, and the pulmonary fissures were classified as either complete or incomplete. Interobserver agreement was assessed with Kappa index (KI). Results: Agreement between all readers for the left oblique, right oblique and horizontal fissure was, respectively, moderate (KI = 0.53), fair (KI = 0.37) and moderate (KI = 0.42). Highest agreement (99/105 fissures) was observed among experienced radiologists, being for left oblique, right oblique and horizontal, respectively, almost perfect (KI = 0.79), perfect (KI = 1.0) and moderate (KI = 0.52). These 2 reviewers found that all of 35 patients had at least one incomplete fissure, with a proportion of incomplete fissures assigned as 74/65%, 85/85% and 91/88%, respectively for the left oblique, right oblique and horizontal fissures. Conclusions: Pneumologists and radiologists agreed fairly to moderately in fissures analysis, while the experienced chest radiologists reached the highest clinically adequate agreement of 94%. We believe that clinical routine visual analysis of the fissures integrity can be done with a good degree of confidence in MDCT images, and experienced readers might be required. Also, a higher than expected incidence of incomplete fissures was described in our studied population.

Incomplete fissures in severe emphysematous patients evaluated with MDCT: Incidence and interobserver agreement among radiologists and pneumologists

International Nuclear Information System (INIS)

Koenigkam-Santos, Marcel; Puderbach, Michael; Gompelmann, Daniela; Eberhardt, Ralf; Herth, Felix; Kauczor, Hans-Ulrich; Heussel, Claus Peter

2012-01-01

Objective: Pulmonary fissures completeness predicts efficacy in endobronchial valves (EBV) implantation, a new lobar volume reduction therapy for severe emphysematous patients. We assessed the incidence of incomplete fissures and the interobserver agreement in its evaluation with MDCT, in severe emphysematous patients prior to EBV implantation. Materials and Methods: Volumetric thin-section CT scans of 35 patients (CODP GOLD 3/4, heterogeneous emphysema) were retrospectively reviewed by 2 pneumologists, 1 general and 2 experienced chest radiologists, independently and blinded for treatment outcome, and the pulmonary fissures were classified as either complete or incomplete. Interobserver agreement was assessed with Kappa index (KI). Results: Agreement between all readers for the left oblique, right oblique and horizontal fissure was, respectively, moderate (KI = 0.53), fair (KI = 0.37) and moderate (KI = 0.42). Highest agreement (99/105 fissures) was observed among experienced radiologists, being for left oblique, right oblique and horizontal, respectively, almost perfect (KI = 0.79), perfect (KI = 1.0) and moderate (KI = 0.52). These 2 reviewers found that all of 35 patients had at least one incomplete fissure, with a proportion of incomplete fissures assigned as 74/65%, 85/85% and 91/88%, respectively for the left oblique, right oblique and horizontal fissures. Conclusions: Pneumologists and radiologists agreed fairly to moderately in fissures analysis, while the experienced chest radiologists reached the highest clinically adequate agreement of 94%. We believe that clinical routine visual analysis of the fissures integrity can be done with a good degree of confidence in MDCT images, and experienced readers might be required. Also, a higher than expected incidence of incomplete fissures was described in our studied population.

Calcul statistique du volume des blocs matriciels d'un gisement fissuré The Statistical Computing of Matrix Block Volume in a Fissured Reservoir

Directory of Open Access Journals (Sweden)

Guez F.

2006-11-01

Full Text Available La recherche des conditions optimales d'exploitation d'un gisement fissuré repose sur une bonne description de la fissuration. En conséquence il est nécessaire de définir les dimensions et volumes des blocs matriciels en chaque point d'une structure. Or la géométrie du milieu (juxtaposition et formes des blocs est généralement trop complexe pour se prêter au calcul. Aussi, dans une précédente communication, avons-nous dû tourner cette difficulté par un raisonnement sur des moyennes (pendages, azimuts, espacement des fissures qui nous a conduits à un ordre de grandeur des volumes. Cependant un volume moyen ne peut pas rendre compte d'une loi de répartition des volumes des blocs. Or c'est cette répartition qui conditionne le choix d'une ou plusieurs méthodes successives de récupération. Aussi présentons-nous ici une méthode originale de calcul statistique de la loi de distribution des volumes des blocs matriciels, applicable en tout point d'un gisement. La part de gisement concernée par les blocs de volume donné en est déduite. La connaissance générale du phénomène de la fracturation sert de base au modèle. Les observations de subsurface sur la fracturation du gisement en fournissent les données (histogramme d'orientation et d'espacement des fissures.Une application au gisement d'Eschau (Alsace, France est rapportée ici pour illustrer la méthode. The search for optimum production conditions for a fissured reservoir depends on having a good description of the fissure pattern. Hence the sizes and volumes of the matrix blocks must be defined at all points in a structure. However, the geometry of the medium (juxtaposition and shapes of blocks in usually too complex for such computation. This is why, in a previous paper, we got around this problem by reasoning on the bases of averages (clips, azimuths, fissure spacing, and thot led us to an order of magnitude of the volumes. Yet a mean volume cannot be used to explain

Fissure fillings from the Klipperaas study site

International Nuclear Information System (INIS)

Tullborg, E.L.

1986-07-01

The Klipperaas study site is located within the Smaaland-Vaermland granitoid belt in southern Sweden. The area investigated can be subdivided into blocks with different hydraulic character and fracture frequency of the rocks. A fissure filling, study has been carried out within the area. This includes identification of the minerals, mineral frequency, textures within the fissures and isotope analyses of calcites. Four generation of fissure fillings, within the time space c. 1600 M.a. to present, has been distinguished. These are 1) quartz; 2) epidote + muscovite and adularia + hematite; 3) calcite + chlorite +/hematite; 4) calcite, clay minerals and Fe-oxyhydroxide. It is observed that the surface water affect the uppermost part of the bedrock resulting in calcite dissolution, break down of pyrite and precipitation of Fe-oxyhydroxide. It is also obvious from the fracture calcite frequency that calcite dissolution is more intensive close to and within the fracture zones. There, Fe-oxyhydroxide can be found down to at least 400 m depth. This gives valuable information about the physic-chemical character of the groundwater within the bedrock. Several fracture zones have been reactivated. It is also suspected that relatively late movements have taken place causing crushing of the rock and only a slight cementation of the crushed material is visible. Some of the fracture zones correspond to mafic dikes. These zones exhibit lower hydraulic conductivity than other zones due to fracture sealing by clay minerals but also by chlorite and calcite. (author)

Measure Guideline: Passive Vents

Energy Technology Data Exchange (ETDEWEB)

Berger, David [Consortium for Advanced Residential Buildings, Norwalk, CT (United States); Neri, Robin [Consortium for Advanced Residential Buildings, Norwalk, CT (United States)

2016-02-05

This document addresses the use of passive vents as a source of outdoor air in multifamily buildings. The challenges associated with implementing passive vents and the factors affecting performance are outlined. A comprehensive design methodology and quantified performance metrics are provided. Two hypothetical design examples are provided to illustrate the process. This document is intended to be useful to designers, decision-makers, and contractors implementing passive ventilation strategies. It is also intended to be a resource for those responsible for setting high-performance building program requirements, especially pertaining to ventilation and outdoor air. To ensure good indoor air quality, a dedicated source of outdoor air is an integral part of high-performance buildings. Presently, there is a lack of guidance pertaining to the design and installation of passive vents, resulting in poor system performance. This report details the criteria necessary for designing, constructing, and testing passive vent systems to enable them to provide consistent and reliable levels of ventilation air from outdoors.

Simulation of the Flow Through Porous Layers Composed of Converging-Diverging Capillary Fissures or Tubes

Science.gov (United States)

Walicka, A.

2018-02-01

In this paper, a porous medium is modelled by a network of converging-diverging capillaries which may be considered as fissures or tubes. This model makes it necessary to consider flows through capillary fissures or tubes. Therefore an analytical method for deriving the relationships between pressure drops, volumetric flow rates and velocities for the following fluids: Newtonian, polar, power-law, pseudoplastic (DeHaven and Sisko types) and Shulmanian, was developed. Next, considerations on the models of pore network for Newtonian and non-Newtonian fluids were presented. The models, similar to the schemes of central finite differences may provide a good basis for transforming the governing equations of a flow through the porous medium into a set of linear or quasi-linear algebraic equations. It was shown that the some coefficients in these algebraic equations depend on the kind of the capillary convergence.

Cutting Whole Length or Partial Length of Internal Anal Sphincter in Managementof Fissure in Ano

Directory of Open Access Journals (Sweden)

Furat Shani Aoda

2017-12-01

Full Text Available A chronic anal fissure is a common painful perianal condition.The main operative procedure to treat this painful condition is a lateral internal sphincteretomy (LIS.The aim of study is to compare the outcome and complications of closed LIS up to the dentate line (whole length of internal sphincter or up to the fissure apex (partial length of internal sphincter in the treatment of anal fissure.It is a prospective comparativestudy including 100 patients with chronic fissure in ano. All patients assigned to undergo closed LIS. Those patients were randomly divided into two groups: 50 patients underwent LIS to the level of dentate line (whole length and other 50 patients underwent LIS to the level of fissure apex (partial length. Patients were followed up weekly in the 1st month, twice monthly in the second month then monthly   for next 2 months and finally after 1 year. There was satisfactory relief of pain in all patients in both groups & complete healing of the fissure occurred. Regarding post operative incontinence no major degree of incontinence occur in both group but minor degree of incontinence persists In 7 patients after whole length LIS after one year. In conclusion, both whole length & partial length LIS associated with improvement of pain, good chance of healing but whole length LIS associated with more chance of long term  flatus incontinence. Hence,we recommend partial length LIS as treatment forchronic anal fissure.

Hydrodynamic calculation of a filter washing in liquids type used in containment venting systems

International Nuclear Information System (INIS)

Reyes G, A. A.; Sainz M, E.; Ortiz V, J.

2015-09-01

From the nuclear accident of Chernobyl, the European nuclear power plants have chosen to install filters on the venting pipes of the containment, whose function is to help to mitigate the consequences of a severe accident, by controlled depressurization of the containment passively through a filtered venting of the containment system. These systems are designed to relieve the internal pressure of the containment by means of the deliberate opening of pressure relief devices, either a valve or rupture disc during a severe accident and be channeled to the filter unit. In this paper the hydraulic response of a filter system of gases washing by liquid is evaluated, due to this information is necessary to estimate the effect that has the pressure increase of the contention on the discharge capacity of the venting pipes. By simulation of computational of fluid dynamics with the programs: CAELINUX-2014 and OpenFOAM, the hydrodynamic characteristics of the Multi Venturi System for gases washing from the containment, which could be included in the general model of the venting pipe, were obtained. Representative models of the Venturi tubes of each concentric area that forming the washing system were generated; and using parametric calculations the average mass flow rate established through each venturi, depending on its size and depth in which it is located inside the tank was estimated. Also, the pressure and mass flow rate required to activate each concentric area depending on the pressure and mass load from the containment were calculated, to estimate the maximum flow that is established through the filter. Finally, the velocity profiles and the characteristic pressure at which each area operates as well as the pressure drop of local and global discharge also were calculated. (Author)

Airborne lidar detection of an underwater thermal vent

Science.gov (United States)

Roddewig, Michael R.; Churnside, James H.; Shaw, Joseph A.

2017-07-01

We report the lidar detection of an underwater feature that appears to be a thermal vent in Yellowstone Lake, Yellowstone National Park, USA, with the Montana State University Fish Lidar. The location of the detected vent was 30 m from the closest vent identified in a United States Geological Survey of Yellowstone Lake in 2008. A second possible vent is also presented, and the appearance of both vents in the lidar data is compared to descriptions of underwater thermal vents in Yellowstone Lake from the geological literature.

Retention of fissure sealants in young permanent molars affected by dental fluorosis: a 12-month clinical study.

Science.gov (United States)

Hasanuddin, S; Reddy, E R; Manjula, M; Srilaxmi, N; Rani, S T; Rajesh, A

2014-10-01

To evaluate and compare retention and caries occurance following placement of Clinpro and FUJI VII fissure sealants, by two different techniques simultaneously in unsealed, contralateral young permanent molars of 7- to 10-year-old children affected by mild to moderate dental fluorosis at various recall intervals of 1 week, 1, 3, 6 and 12 months. 80 schoolchildren with mild to moderate dental fluorosis were assigned to Group A and Group B with 40 children in each group. In Group A Clinpro fissure sealant and in Group B Fuji VII fissure sealant was used. In both the groups fissure sealants were applied by conventional fissure sealant technique (CST) on one side and enameloplasty sealant technique (EST) on the other side of the same arch. The applied fissure sealants were evaluated clinically for retention and caries incidence. Clinpro fissure sealant showed a retention rate of 95% when compared with Fuji VII (57.5%) at the end of 12 months, which was statistically significant. Regarding techniques, EST showed better results than CST in both the groups. Comparison of groups with respect to retention and techniques at different time periods was performed using Mann-Whitney U test (p < 0.05). Comparison of different time periods with respect to retention and technique in all the groups was performed using Wilcoxon matched pairs test by ranks (p < 0.05). Clinpro fissure sealant showed better retention at all treatment intervals, when compared with Fuji VII. Further follow-up is required to study the efficacy of the fissure sealant placement techniques.

Traumatic superior orbital fissure syndrome: assessment of cranial nerve recovery in 33 cases.

Science.gov (United States)

Chen, Chien-Tzung; Wang, Theresa Y; Tsay, Pei-Kwei; Huang, Faye; Lai, Jui-Pin; Chen, Yu-Ray

2010-07-01

Superior orbital fissure syndrome is a rare complication that occurs in association with craniofacial trauma. The characteristics of superior orbital fissure syndrome are attributable to a constellation of cranial nerve III, IV, and VI palsies. This is the largest series describing traumatic superior orbital fissure syndrome that assesses the recovery of individual cranial nerve function after treatment. In a review from 1988 to 2002, 33 patients with superior orbital fissure syndrome were identified from 11,284 patients (0.3 percent) with skull and facial fractures. Severity of cranial nerve injury and functional recovery were evaluated by extraocular muscle movement. Patients were evaluated on average 6 days after initial injury, and average follow-up was 11.8 months. There were 23 male patients. The average age was 31 years. The major mechanism of injury was motorcycle accident (67 percent). Twenty-two received conservative treatment, five were treated with steroids, and six patients underwent surgical decompression of the superior orbital fissure. After initial injury, cranial nerve VI suffered the most damage, whereas cranial nerve IV sustained the least. In the first 3 months, recovery was greatest in cranial nerve VI. At 9 months, function was lowest in cranial nerve VI and highest in cranial nerve IV. Eight patients (24 percent) had complete recovery of all cranial nerves. Functional recovery of all cranial nerves reached a plateau at 6 months after trauma. Cranial nerve IV suffered the least injury, whereas cranial nerve VI experienced the most neurologic deficits. Cranial nerve palsies improved to their final recovery endpoints by 6 months. Surgical decompression is considered when there is evidence of bony compression of the superior orbital fissure.

The effect of fissures on the strength of structural timber

Directory of Open Access Journals (Sweden)

Íñiguez, Guillermo

2010-06-01

Full Text Available Detailed measurements of drying fissures were carried out on 28 pieces of gross cross-section structural Scots pine timber. Different parameters have been proposed to measure their magnitude: length, depth, thickness and slope of grain, as well as an index of area in the neutral axis plane (ratio of effective to total surface. The parameters of fissures have been related to bending strength, shear strength, modulus of elasticity and rupture energy obtained from mechanical tests, considering whether rupture is due to bending or shear. All of the fissures observed allows to classify the pieces as MEG according to the UNE 56544 standard. To quantify the magnitude of fissures the index of areas is proposed, while mechanical properties can be quantified by rupture energy. Analysis of the results does not show any relation between the fissures analyzed and the mode of failure, their magnitude and mechanical properties..

Se han realizado mediciones detalladas de las fendas de secado en 28 piezas de madera de pino silvestre de gran escuadría. Se han propuesto diferentes parámetros para medir su magnitud en longitud, profundidad, grosor e inclinación, así como un índice de áreas en el plano medio de rasante (superficie eficaz respecto a superficie total. Se han relacionado los parámetros de fendas con resistencia a flexión, resistencia a cortante, módulo de elasticidad y energía de rotura obtenidos mediante ensayos mecánicos, teniendo en cuenta si la rotura se produce por flexión o por cortante. Todas las fendas observadas permiten clasificar las piezas como MEG según la norma UNE 56544. Se propone cuantificar las fendas mediante el índice de áreas y las propiedades mecánicas mediante la energía de rotura. El análisis realizado no muestra una relación significativa entre las fendas analizadas, los modos de rotura o las propiedades mecánicas.

THE EFFECT OF FISSURES IN DOLOMITE ROCK MASS ON BLASTING PROJECTS

Directory of Open Access Journals (Sweden)

Branko Božić

1989-12-01

Full Text Available Rock fractures in the form of fissures are one of more important geological features of a tectonic system. They have an effect on mechanical behaviour of rook masses exposed to the actions of surface forces. For exploitation in dolomite quarries carried out by blasting of deep shot holes it is important to know the system of fissures within a rock mass for the rock brakes along already weakened planes (the paper is published in Croatian.

Thermomechanical behavior of mica layers with lenticular fissures

Science.gov (United States)

Yang, Michael Xinyi

The thermomechanical behavior of natural phlogopite mica specimens from seven different origins is characterized. An initial heat treatment, to a temperature between 300°C and 400°C, is found to form fissures that stabilize in the material. Following the initial heat treatment, all the phlogopite specimens, regardless of their origin and polytype, exhibit the extraordinarily large thermal expansion (intumescence), more than 200% at 600°C, in the direction perpendicular to the basal planes. This phenomenon is strictly reproducible when tested under a range of thermal conditions including thermal shock, multiple thermal fatigue cycles, varying heating or cooling rates and isothermal heating over an extensive period of time at different temperatures up to 585°C. The hysteresis, associated with the thermal cycle, is increased when the specimen is heated or cooled at a faster rate. The maximum coefficient of linear thermal expansion, approximately 10 -2°C-1, is observed over the temperature range 100--120°C. This is due to the non-structural water, entrapped within the layer structure, which undergoes a phase transition and causes the mica layers to expand abruptly. A model of lenticular fissures is developed based on thin-plate mechanics and thermodynamics assumptions. The state of a lenticular fissure with water vapor molecules is determined to correlate the experimental parameters with the material properties. The average density of water vapor molecules within a lenticular fissure is calculated to be ˜1025 m 3 for the temperature interval between 100°C and 275°C. The concentration of non-structure water, based on the model calculation, is less than 0.1% by weight. Acoustic emission (AE) signals have been reported by Pranevicius et al. (1995) to correspond to the microstructure changes as the internal lenticular fissures develop in phlogopite. This technique has also been proven feasible to characterize the thermomechanical behavior of other layer structures

The economics of pit and fissure sealants in preventive dentistry: a review.

Science.gov (United States)

Kitchens, Dinah H

2005-08-15

Oral diseases are progressive, cumulative, and become more intricate to treat with advancement. While dental caries is an infectious transmissible disease with children being at the highest risk, primary prevention can reduce this risk. Primary prevention in dentistry is usually considered to be community fluoridated water supplies, professional fluoride treatments, and pit and fissure sealants. While community fluoridated water supplies have been proven to be cost-effective, the cost-effectiveness of pit and fissure sealants has primarily been studied in school-based programs of children from low socio-economic backgrounds. Dental sealant programs are just one way to help increase primary prevention in the oral health disparities of children. The purpose of this paper is to review the literature regarding the cost-effectiveness of pit and fissure sealants as a preventive strategy in preventive dentistry.

Venting of gas deflagrations through relief pipes

OpenAIRE

Ferrara, Gabriele

2006-01-01

Vent devices for gas and dust explosions are often ducted to safety locations by means of relief pipes for the discharge of hot combustion products or blast waves (NFPA 68, 2002). The presence of the duct is likely to increase the severity of the explosion with respect to simply vented vessels posing a problem for the proper design of this venting configuration. The phenomenology of the vented explosion is complicated as the interaction of combustion in the duct with primary combustion in...

Subpial Hematoma and Extravasation in the Interhemispheric Fissure with Subarachnoid Hemorrhage

Science.gov (United States)

Matsuoka, Go; Abe, Kayoko; Okada, Yoshikazu; Sakai, Shuji

2015-01-01

A recent report on computed tomography (CT) findings of contrast extravasation in subarachnoid hemorrhage (SAH) with Sylvian hematoma suggests that the occurrence of the hematoma is secondary to bleeding in the subpial space. Our patient was in his sixties and was admitted to the hospital because of loss of consciousness (Glasgow Coma Scale E4V1M4). SAH was diagnosed in plain head CT, and growing hematomas were observed in the Sylvian and interhemispheric fissures following a subarachnoid hemorrhage. CT angiography (CTA) using a dual-phase scan protocol revealed contrast extravasation in both the fissures in the latter phase, and hematoma in the interhemispheric fissure contained multiple bleeding points. This case indicates that the occurrence of subpial hematoma such as Sylvian hematoma can be a secondary event following subpial bleeding from damaged small vessels elsewhere in the cranium. Instead of four-dimensional (4D) CT, the dual-phase CTA technique may help detect minor extravasations with usual helical CT scanner. PMID:25963159

Numerical analysis on the crack propagation and failure characteristics of rocks with double fissures under the uniaxial compression

Directory of Open Access Journals (Sweden)

Leyong Chen

2015-12-01

Full Text Available The fissures and rock bridges with different dips had different contributions to crack's initiation, propagation, convergence and penetration. In this paper, based on the rock fracture theory, the crack's propagation and evolution process on rock specimen with double fissures under uniaxial compression was simulated. As a result, the crack propagation and evolution law of rocks with different fissure dips (α = 0°, 15°, 30°, 45°, 60°, 75°, 90°; β = 45° and different rock bridge dips (β = 0°, 30°, 45°, 60°, 90°; α = 45° was obtained by numerical tests. Meanwhile, the fissure and rock bridge dips influence on the macro mechanical properties of rock was analyzed. Besides, the paper investigated the influences of different fissure dips and different rock bridge dips on the bridge transfixion. The study is of great significance to reveal the impact of different dips on the mechanical mechanism of multiple-fissures rock under specific conditions, and it also has important theoretical significance for the research on multiple-fissure rock.

Land subsidence, Ground Fissures and Buried Faults: InSAR Monitoring of Ciudad Guzmán (Jalisco, Mexico

Directory of Open Access Journals (Sweden)

Carlo Alberto Brunori

2015-07-01

Full Text Available We study land subsidence processes and the associated ground fissuring, affecting an active graben filled by thick unconsolidated deposits by means of InSAR techniques and fieldwork. On 21 September 2012, Ciudad Guzmán (Jalisco, Mexico was struck by ground fissures of about 1.5 km of length, causing the deformation of the roads and the propagation of fissures in adjacent buildings. The field survey showed that fissures alignment is coincident with the escarpments produced on 19 September 1985, when a strong earthquake with magnitude 8.1 struck central Mexico. In order to detect and map the spatio-temporal features of the processes that led to the 2012 ground fissures, we applied InSAR multi-temporal techniques to process ENVISAT-ASAR and RADARSAT-2 satellite SAR images acquired between 2003 and 2012. We detect up to 20 mm/year of subsidence of the northwestern part of Ciudad Guzmán. These incremental movements are consistent with the ground fissures observed in 2012. Based on interferometric results, field data and 2D numerical model, we suggest that ground deformations and fissuring are due to the presence of areal subsidence correlated with variable sediment thickness and differential compaction, partly driven by the exploitation of the aquifers and controlled by the distribution and position of buried faults.

Three-armed rifts or masked radial pattern of eruptive fissures? The intriguing case of El Hierro volcano (Canary Islands)

Science.gov (United States)

Becerril, L.; Galindo, I.; Martí, J.; Gudmundsson, A.

2015-04-01

Using new surface structural data as well as subsurface structural data obtained from seventeen water galleries, we provide a comprehensive model of the volcano-tectonic evolution of El Hierro (Canary Islands). We have identified, measured and analysed more than 1700 volcano-structural elements including vents, eruptive fissures, dykes and faults. The new data provide important information on the main structural patterns of the island and on its stress and strain fields, all of which are crucial for reliable hazard assessments. We conducted temporal and spatial analyses of the main structural elements, focusing on their relative age and association with the three main cycles in the construction of the island: the Tiñor Edifice, the El Golfo-Las Playas Edifice, and the Rift Volcanism. A radial strike distribution, which can be related to constructive episodes, is observed in the on-land structures. A similar strike distribution is seen in the submarine eruptive fissures, which are radial with respect to the centre of the island. However, the volcano-structural elements identified onshore and reflecting the entire volcano-tectonic evolution of the island also show a predominant NE-SW strike, which coincides with the main regional trend of the Canary archipelago as a whole. Two other dominant directions of structural elements, N-S and WNW-ESE, are evident from the establishment of the El Golfo-Las Playas edifice, during the second constructive cycle. We suggest that the radial-striking structures reflect comparatively uniform stress fields during the constructive episodes, mainly conditioned by the combination of overburden pressure, gravitational spreading, and magma-induced stresses in each of the volcanic edifices. By contrast, in the shallower parts of the edifice the NE-SW, N-S and WNW-ESE-striking structures reflect local stress fields related to the formation of mega-landslides and masking the general and regional radial patterns.

In Vitro Comparison of Microleakage of Two Materials Used as Pit and Fissure Sealants

Directory of Open Access Journals (Sweden)

Zahra Bahrololoomi

2011-09-01

Full Text Available Background and aims. Marginal seal of the material is extremely important in fissure sealant therapy. The aim of this study was to investigate microleakage of flowable composite resins and conventional fissure sealants with or without dentin bonding agent. Materials and methods. The occlusal surface of 60 intact extracted human premolars, divided into four groups, were cleaned with pumice/slurry, etched with 37% phosphoric acid for 15 seconds, rinsed and dried. Groups were treated differently: Excite bonding agent followed by Helioseal F fissure sealant in group1; Helioseal F alone in group 2; Excite bonding agent followed by Tetric Flow in group 3; and Tetric Flow alone in group 4. Light-curing was done after each application. After thermocycling, the whole surface of each specimen was coated with nail varnish except for one millimeter around the fissure sealant. The teeth were immersed in 2% basic fuchsin for 24 hours and then sectioned buccolingually. The sections were analyzed for leakage under a stereomicroscope. Data was analyzed by Kruskal-Wallis and Mann-Whitney tests at a significance level of P 0.05, except for groups 2 and 4 (P = 0.002 and groups 3 and 4 (P = 0.033. Conclusion. Use of a flowable composite with bonding agent is a good alternative for sealing pits and fissures; however, further in vitro and in vivo studies are necessary.

14 CFR 27.975 - Fuel tank vents.

Science.gov (United States)

2010-01-01

... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false Fuel tank vents. 27.975 Section 27.975... STANDARDS: NORMAL CATEGORY ROTORCRAFT Powerplant Fuel System § 27.975 Fuel tank vents. (a) Each fuel tank... system must be designed to minimize spillage of fuel through the vents to an ignition source in the event...

Copepod colonization of organic and inorganic substrata at a deep-sea hydrothermal vent site on the Mid-Atlantic Ridge

Science.gov (United States)

Plum, Christoph; Pradillon, Florence; Fujiwara, Yoshihiro; Sarrazin, Jozée

2017-03-01

The few existing studies on deep-sea hydrothermal vent copepods indicate low connectivity with surrounding environments and reveal high endemism among vents. However, the finding of non-endemic copepod species in association with engineer species at different reduced ecosystems poses questions about the dispersal of copepods and the colonization of hydrothermal vents as well as their ecological connectivity. The objective of this study is to understand copepod colonization patterns at a hydrothermal vent site in response to environmental factors such as temperature and fluid flow as well as the presence of different types of substrata. To address this objective, an in situ experiment was deployed using both organic (woods, pig bones) and inorganic (slates) substrata along a gradient of hydrothermal activity at the Lucky Strike vent field (Eiffel Tower, Mid-Atlantic Ridge). The substrata were deployed in 2011 during the MoMARSAT cruise and were recovered after two years in 2013. Overall, copepod density showed significant differences between substrata types, but was similar among different hydrothermal activity regimes. Highest densities were observed on woods at sites with moderate or low fluid input, whereas bones were the most densely colonized substrata at the 2 sites with higher hydrothermal influence. Although differences in copepod diversity were not significant, the observed trends revealed overall increasing diversity with decreasing temperature and fluid input. Slates showed highest diversity compared to the organic substrata. Temperature and fluid input had a significant influence on copepod community composition, resulting in higher similarity among stations with relatively high and low fluid inputs, respectively. While vent-specialists such as dirivultids and the tegastid Smacigastes micheli dominated substrata at high vent activity, the experiment demonstrated increasing abundance and dominance of non-vent taxa with decreasing temperature and fluid

40 CFR 63.693 - Standards: Closed-vent systems and control devices.

Science.gov (United States)

2010-07-01

... concentration level, design average temperature of the condenser exhaust vent stream, and the design average... requirements specified in paragraphs (d) through (h) of this section as applicable to the type and design of... paragraphs (d) through (h) of this section as applicable to the type and design of the control device...

The Biological Deep Sea Hydrothermal Vent as a Model to Study Carbon Dioxide Capturing Enzymes

Directory of Open Access Journals (Sweden)

Premila D. Thongbam

2011-04-01

Full Text Available Deep sea hydrothermal vents are located along the mid-ocean ridge system, near volcanically active areas, where tectonic plates are moving away from each other. Sea water penetrates the fissures of the volcanic bed and is heated by magma. This heated sea water rises to the surface dissolving large amounts of minerals which provide a source of energy and nutrients to chemoautotrophic organisms. Although this environment is characterized by extreme conditions (high temperature, high pressure, chemical toxicity, acidic pH and absence of photosynthesis a diversity of microorganisms and many animal species are specially adapted to this hostile environment. These organisms have developed a very efficient metabolism for the assimilation of inorganic CO2 from the external environment. In order to develop technology for the capture of carbon dioxide to reduce greenhouse gases in the atmosphere, enzymes involved in CO2 fixation and assimilation might be very useful. This review describes some current research concerning CO2 fixation and assimilation in the deep sea environment and possible biotechnological application of enzymes for carbon dioxide capture.

Comparison of various concentrations of tricalcium phosphate nanoparticles on mechanical properties and remineralization of fissure sealants.

Directory of Open Access Journals (Sweden)

Sara Tavassoli-Hojjati

2014-08-01

Full Text Available The aim of this study was to investigate the mechanical properties (flexural strength, micro-shear bond strength and remineralizing potential of fissure sealants by adding various concentrations of β-tricalcium phosphate nanoparticles.This in-vitro study consisted of five experimental groups containing prepared nano-fisssure sealants (1-5 wt.% β-TCP nanoparticles and two control groups containing a prepared and a commercial fissure sealant. Flexural/micro-shear bond strength values were measured using Zwick test machine. Cavities on sixty healthy premolar teeth were filled with the fissure sealants containing 0-5 wt.% of nano β-TCP. The samples were assessed for remineralization under scanning electron microscopy (SEM and EDAX. Kolmogorov-Smirnov test, One-way ANOVA and Tukey's Post Hoc analysis/HSD were used to analyze the data.There was no significant difference between the flexural strengths/elastic modulus of the 0-5 wt.% nano β-TCP groups (p>0.05. The average flexural strength/elastic modulus of the prepared fissure sealant group (0% was significantly higher than the commercial fissure sealant group (Clinpro (p0.05. Examining the samples under SEM showed a significant increase in thickness of the intermediate layer with increasing concentrations of β-TCP nanoparticles (p<0.05.Addition of 1-5 wt.% β-TCP nanoparticles to the fissure sealants significantly increased the remineralization potential without affecting the mechanical properties.

A model of hydrological and mechanical feedbacks of preferential fissure flow in a slow-moving landslide

Directory of Open Access Journals (Sweden)

D. M. Krzeminska

2013-03-01

Full Text Available The importance of hydrological processes for landslide activity is generally accepted. However, the relationship between precipitation, hydrological responses and movement is not straightforward. Groundwater recharge is mostly controlled by the hydrological material properties and the structure (e.g., layering, preferential flow paths such as fissures of the unsaturated zone. In slow-moving landslides, differential displacements caused by the bedrock structure complicate the hydrological regime due to continuous opening and closing of the fissures, creating temporary preferential flow paths systems for infiltration and groundwater drainage. The consecutive opening and closing of fissure aperture control the formation of a critical pore water pressure by creating dynamic preferential flow paths for infiltration and groundwater drainage. This interaction may explain the seasonal nature of the slow-moving landslide activity, including the often observed shifts and delays in hydrological responses when compared to timing, intensity and duration of precipitation. The main objective of this study is to model the influence of fissures on the hydrological dynamics of slow-moving landslide and the dynamic feedbacks between fissures, hydrology and slope stability. For this we adapt the spatially distributed hydrological and slope stability model (STARWARS to account for geotechnical and hydrological feedbacks, linking between hydrological response of the landside and the dynamics of the fissure network and applied the model to the hydrologically controlled Super-Sauze landslide (South French Alps.

Microleakage, adaptation ability and clinical efficacy of two fluoride releasing fissure sealants

Directory of Open Access Journals (Sweden)

Marković Dejan

2012-01-01

Full Text Available Background/Aim. Retention of fissure sealants and good adaptation to enamel are essential for their success. Fluoride releasing resin-based materials are widely accepted for pit and fissure sealing, but newly designed glass ionomers can serve as a good alternative. The aim of this study was to evaluate microleakage and sealing ability in vitro, and to clinically assess two fluoride releasing fissure sealants. Methods. The sample for experimental study consisted of 20 freshly extracted intact human third molars, divided in two experimental groups according to the sealing material: fluoride releasing resin-based (Heliosel F and glass ionomer (Fuji Triage material. Digital images and scanning electron microscope were used to assess microleakage and adaptation ability. Sample for clinical study consisted of 60 children, aged 6-8 years, with high caries risk, divided in two groups according to the sealant material. Fissure sealant was applied to all erupted, caries-free first permanent molars. Sealants were evaluated after 3, 6 and 12 months using modified Ryge criteria for retention, marginal adaptation, colour match, surface smoothness and caries. Results. Microleakage was detected in more than half of the specimen, without significant differences between the two groups (p > 0.05. Both materials exhibited acceptable sealing ability. Complete retention at the end of the observation period was 81.8% for resin-based, and 21.1% for glass-ionomer fissure sealant (p < 0.001. The presence of caries in sealed molars has been detected in one patient in both groups. During the 12-month observation period, Helioseal F demonstrated better retention, marginal adaptation and surface smoothness (p < 0.001. There were no differences between the two materials regarding caries and color match (p > 0.05. Conclusion. Both tested materials demonstrate satisfactory clinical and caries prophylactic characteristics that justify their use in contemporary preventive

An MR study on widening of the anterior cerebral longitudinal fissure in patients with schizophrenia

International Nuclear Information System (INIS)

Yoshizawa, Masao; Nagumo, Ichiro; Kimura, Hiroko; Yamamoto, Setsuko; Kumagai, Hideo; Ito, Hisao.

1994-01-01

One-hundred and four schizophrenics and 27 normal controls underwent magnetic resonance imaging. The angles of the anterior cerebral longitudial (ACL) fissure on T 1 weighted images were measured on the axial slices at the level of the third ventricle. The schizophrenics had significantly larger angles of ACL fissure than controls. However, the effect of aging might be associated with this phenomenon. There was no correlation between subtype of schizophrenia and the augment of the fissure angle, nor correlation between the duration of schizophrenia and that augment. From this study, it can be concluded that if the fissure angle is larger than 12 degree the finding is regarded as abnormal, because 95% confidence region of the control group was at 11.1 degree. Twenty two schizophrenics revealed the findings and great majority of these patients were suffering from emotional withdrawal and blunted affect. (author)

24 CFR 3280.710 - Venting, ventilation and combustion air.

Science.gov (United States)

2010-04-01

... 24 Housing and Urban Development 5 2010-04-01 2010-04-01 false Venting, ventilation and combustion... Fuel Burning Systems § 3280.710 Venting, ventilation and combustion air. (a) The venting as required by... appliance listing and the appliance manufacturer's instructions. (b) Venting and combustion air systems...

Injectabilite des coulis de ciment dans des milieux fissures

Science.gov (United States)

Mnif, Thameur

Le travail presente ici est un bilan du travaux de recherche effectues sur l'injectabilite des coulis de ciment dans lu milieux fissures. Un certain nombre de coulis a base de ciment Portland et microfin ont ete selectionnes afin de caracteriser leur capacite a penetrer des milieux fissures. Une partie des essais a ete menee en laboratoire. L'etude rheologique des differents melanges a permis de tester l'influence de l'ajout de superplastifiant et/ou de fumee de silice sur la distribution granulometrique des coulis et par consequent sur leur capacite a injecter des colonnes de sable simulant un milieu fissure donne. La classe granulometrique d'un coulis, sa stabilite et sa fluidite sont apparus comme les trois facteurs principaux pour la reussite d'une injection. Un facteur de finesse a ete defini au cours de cette etude: base sur la classe granulometrique du ciment et sa stabilite, il peut entrer dans la formulation theorique du debit d'injection avant application sur chantier. La deuxieme et derniere partie de l'etude presente les resultats de deux projets de recherche sur l'injection realises sur chantier. L'injection de dalles de beton fissurees a permis le suivi de l'evolution des pressions avec la distance au point d'injection. L'injection de murs de maconnerie a caractere historique a montre l'importance de la definition de criteres de performance des coulis a utiliser pour traiter un milieu donne et pour un objectif donne. Plusieurs melanges peuvent ainsi etre predefinis et mis a disposition sur le chantier. La complementarite des ciments traditionnels et des ciments microfins devient alors un atout important. Le choix d'utilisation de ces melanges est fonction du terrain rencontre. En conclusion, cette recherche etablit une methodologie pour la selection des coulis a base de ciment et des pressions d'injection en fonction de l'ouverture des fissures ou joints de construction.

Fissure formation in coke. 3: Coke size distribution and statistical analysis

Energy Technology Data Exchange (ETDEWEB)

D.R. Jenkins; D.E. Shaw; M.R. Mahoney [CSIRO, North Ryde, NSW (Australia). Mathematical and Information Sciences

2010-07-15

A model of coke stabilization, based on a fundamental model of fissuring during carbonisation is used to demonstrate the applicability of the fissuring model to actual coke size distributions. The results indicate that the degree of stabilization is important in determining the size distribution. A modified form of the Weibull distribution is shown to provide a better representation of the whole coke size distribution compared to the Rosin-Rammler distribution, which is generally only fitted to the lump coke. A statistical analysis of a large number of experiments in a pilot scale coke oven shows reasonably good prediction of the coke mean size, based on parameters related to blend rank, amount of low rank coal, fluidity and ash. However, the prediction of measures of the spread of the size distribution is more problematic. The fissuring model, the size distribution representation and the statistical analysis together provide a comprehensive capability for understanding and predicting the mean size and distribution of coke lumps produced during carbonisation. 12 refs., 16 figs., 4 tabs.

A method for the automatic quantification of the completeness of pulmonary fissures: evaluation in a database of subjects with severe emphysema

Energy Technology Data Exchange (ETDEWEB)

Rikxoort, Eva M. van; Goldin, Jonathan G.; Galperin-Aizenberg, Maya; Abtin, Fereidoun; Kim, Hyun J.; Lu, Peiyun; Shaw, Greg; Brown, Matthew S. [University of California-Los Angeles, Center for Computer Vision and Imaging Biomarkers and Thoracic Imaging Research Group, Department of Radiological Sciences, David Geffen School of Medicine, Los Angeles, CA (United States); Ginneken, Bram van [Radboud University Nijmegen Medical Centre, Diagnostic Image Analysis Group, Department of Radiology, Nijmegen (Netherlands); University Medical Center Utrecht, Image Sciences Institute, Department of Radiology, Utrecht (Netherlands)

2012-02-15

To propose and evaluate a technique for automatic quantification of fissural completeness from chest computed tomography (CT) in a database of subjects with severe emphysema. Ninety-six CT studies of patients with severe emphysema were included. The lungs, fissures and lobes were automatically segmented. The completeness of the fissures was calculated as the percentage of the lobar border defined by a fissure. The completeness score of the automatic method was compared with a visual consensus read by three radiologists using boxplots, rank sum tests and ROC analysis. The consensus read found 49% (47/96), 15% (14/96) and 67% (64/96) of the right major, right minor and left major fissures to be complete. For all fissures visually assessed as being complete the automatic method resulted in significantly higher completeness scores (mean 92.78%) than for those assessed as being partial or absent (mean 77.16%; all p values <0.001). The areas under the curves for the automatic fissural completeness were 0.88, 0.91 and 0.83 for the right major, right minor and left major fissures respectively. An automatic method is able to quantify fissural completeness in a cohort of subjects with severe emphysema consistent with a visual consensus read of three radiologists. (orig.)

Numerical Study of Severe Accidents on Containment Venting Conditions

Energy Technology Data Exchange (ETDEWEB)

Lee, Na Rae; Bang, Young Suk; Park, Tong Kyu; Lee, Doo Yong [FNC Technology Co., Yongin (Korea, Republic of); Choi, Yu Jung; Lee, Sang Won; Kim, Hyeong Taek [KHNP-CRI, Daejeon (Korea, Republic of)

2014-10-15

Under severe accident, the containment integrity can be challenged due to over-pressurization by steam and non-condensable gas generation. According to Seismic Probabilistic Safety Assessment (PSA) result, the late containment failure by over-pressurization has been identified as the most probable containment failure mode. In addition, the analyses of Fukushima nuclear power plant accident reveal the necessity of the proper containment depressurization to prevent the large release of the radionuclide to environment. Containment venting has been considered as an effective approach to maintain the containment integrity from over-pressurization. Basic idea of containment venting is to relieve the pressure inside of the containment by establishing a flow path to the external environment. To ensure the containment integrity under over-pressure conditions, it is crucial to conduct the containment vent in a timely manner with a sufficient discharge flow rate. It is also important to optimize the vent line size to prevent additional risk of leakage and to install at the site with limited space availability. The purpose of this study is to identify the effective venting conditions for preventing the containment over-pressurization and investigate the vent flow characteristics to minimize the consequence of the containment ventilation.. In order that, thermodynamic behavior of the containment and the discharged flow depending on different vent strategies are analyzed and compared. The representative accident scenarios are identified by reviewing the Level 2 PSA result and the sensitivity analyses with varying conditions (i.e. vent line size and vent initiation pressure) are conducted. MAAP5 model for the OPR1000 Korea nuclear power plant has been used for severe accident simulations. Containment venting can be an effective strategy to prevent the significant failure of the containment due to over-pressurization. However, it should be carefully conducted because the vented

Numerical Study of Severe Accidents on Containment Venting Conditions

International Nuclear Information System (INIS)

Lee, Na Rae; Bang, Young Suk; Park, Tong Kyu; Lee, Doo Yong; Choi, Yu Jung; Lee, Sang Won; Kim, Hyeong Taek

2014-01-01

Under severe accident, the containment integrity can be challenged due to over-pressurization by steam and non-condensable gas generation. According to Seismic Probabilistic Safety Assessment (PSA) result, the late containment failure by over-pressurization has been identified as the most probable containment failure mode. In addition, the analyses of Fukushima nuclear power plant accident reveal the necessity of the proper containment depressurization to prevent the large release of the radionuclide to environment. Containment venting has been considered as an effective approach to maintain the containment integrity from over-pressurization. Basic idea of containment venting is to relieve the pressure inside of the containment by establishing a flow path to the external environment. To ensure the containment integrity under over-pressure conditions, it is crucial to conduct the containment vent in a timely manner with a sufficient discharge flow rate. It is also important to optimize the vent line size to prevent additional risk of leakage and to install at the site with limited space availability. The purpose of this study is to identify the effective venting conditions for preventing the containment over-pressurization and investigate the vent flow characteristics to minimize the consequence of the containment ventilation.. In order that, thermodynamic behavior of the containment and the discharged flow depending on different vent strategies are analyzed and compared. The representative accident scenarios are identified by reviewing the Level 2 PSA result and the sensitivity analyses with varying conditions (i.e. vent line size and vent initiation pressure) are conducted. MAAP5 model for the OPR1000 Korea nuclear power plant has been used for severe accident simulations. Containment venting can be an effective strategy to prevent the significant failure of the containment due to over-pressurization. However, it should be carefully conducted because the vented

40 CFR 63.1326 - Batch process vents-recordkeeping provisions.

Science.gov (United States)

2010-07-01

....1325(e) for aggregate batch vent streams; (ii) For a boiler or process heater, a description of the location at which the vent stream is introduced into the boiler or process heater; (iii) For a boiler or... process vents or halogenated aggregate batch vent streams, the percent reduction of total hydrogen halides...

Pit and fissure sealants versus fluoride varnishes for preventing dental decay in children and adolescents

DEFF Research Database (Denmark)

Hiiri, Anne; Ahovuo-Saloranta, Anneli; Nordblad, Anne

2010-01-01

the effectiveness of pit and fissure sealants to be statistically significantly higher than an application of fluoride varnish every 6 months in preventing occlusal decays of first molars at 23 months (with a RR of 0.74, 95% confidence interval (CI) 0.58 to 0.95); and at 4 years and 9 years (with a RR of 0.42, 95...... caries on the fluoride varnished tooth surfaces, compared to sealed plus fluoride varnished surfaces, with a RR of 0.36 (95% CI 0.21 to 0.61). AUTHORS' CONCLUSIONS: There was some evidence on the superiority of pit and fissure sealants over fluoride varnish application in the prevention of occlusal......BACKGROUND: The majority of the detected increment in dental caries among children and adolescents is confined to pit and fissure surfaces of first molars. OBJECTIVES: The objective of this study was to compare the effectiveness of pit and fissure sealants with fluoride varnishes in the prevention...

Pit and fissure sealants for preventing dental decay in permanent teeth

DEFF Research Database (Denmark)

Ahovuo-Saloranta, Anneli; Forss, Helena; Walsh, Tanya

2017-01-01

to 3 August 2016), and Embase Ovid (1980 to 3 August 2016). We searched ClinicalTrials.gov and the World Health Organization International Clinical Trials Registry Platform for ongoing trials to 3 August 2016. No restrictions were placed on language or date of publication. Selection criteria......Background: Dental sealants were introduced in the 1960s to help prevent dental caries, mainly in the pits and fissures of occlusal tooth surfaces. Sealants act to prevent bacteria growth that can lead to dental decay. Evidence suggests that fissure sealants are effective in preventing caries....... Further research with long follow-up is needed....

Thermal hydraulic analysis of BWR containment venting system

International Nuclear Information System (INIS)

Baburajan, P.K.; Sharma, Prashant; Paul, U.K.; Gaikwad, Avinash

2015-01-01

Installation of additional containment filtered venting system (CFVS) is necessary to depressurize the containment to maintain its mechanical integrity due to over pressurization during severe accident condition. A typical venting system for BWR is modelled using RELAP5 and analysed to investigate the effect of various thermal hydraulic parameters on the operational parameters of the venting system. The venting system consists of piping from the containment to the scrubber tank and exit line from the scrubber tank. The scrubber tank is partially filled with water to enable the scrubbing action to remove the particulate radionuclides from the incoming containment air. The pipe line from the containment is connected to the venturi inlet and the throat of the venturi is open to the scrubber tank water inventory at designed submergence level. The exit of the venturi is open to scrubber tank water. Filters are used in the upper air space of the scrubber tank as mist separator before venting out the air into the atmosphere through the exit vent line. The effect of thermal hydraulic parameters such as inlet fluid temperature, inlet steam content and venturi submergence in the scrubber tank on the venting flow rate, exit steam content, scrubber tank inventory, overflow line and siphon breaker flow rate is analysed. Results show that inlet steam content and the venturi nozzle submergence influence the venting system parameters. (author)

Effect of an Antibacterial Monomer on the Antibacterial Activity of a Pit-and-Fissure Sealant.

Directory of Open Access Journals (Sweden)

Fan Yu

Full Text Available Resin-based pit-and-fissure sealants are often used to form a barrier on the occlusal surface of molars to treat caries lesions; however, bacteria can remain in the pit and fissures without detection, increasing the risk of secondary caries. Sealants with antimicrobial properties or microbial repellent actions might be advantageous. The aim of this study was to assess the inhibitory effect of a 2-methacryloxylethyl dodecyl methyl ammonium bromide (MAE-DB-incorporated sealant against Streptococcus mutans. MAE-DB (4% wt was incorporated into a commercially available sealant, Eco-S resin-based pit-and-fissure sealant (Vericom Co., Ltd., Korea; a sealant without MAE-DB served as a negative control, and Clinpro™ Sealant (3M™ ESPE™, a fluoride-releasing resin, was used as a commercial control. The effects of the cured sealants and their eluents on the growth of S. mutans were determined according to colony-forming unit counts and metabolic tests. The effects of the cured sealants on the adherence and membrane integrity of S. mutans were investigated using confocal laser-scanning microscopy (CLSM in conjunction with fluorescent indicators. Compared with the negative control and commercial control, the cured MAE-DB-incorporated pit-and-fissure sealant exhibited a significant inhibitory effect on the growth of S. mutans (P < 0.05, whereas the eluents did not show any detectable antibacterial activity. The commercial control also showed no detectable bactericidal activity. Moreover, the aged experimental material retained its property of contact inhibition of biofilm formation. The fluorescence analysis of CLSM images demonstrated that the cured MAE-DB-incorporated sealant could hamper the adherence of S. mutans and exert a detrimental effect on bacterial membrane integrity. The incorporation of MAE-DB can render a pit-and-fissure sealant with contact antibacterial activity after polymerization via influencing the growth, adherence, and membrane

A bestiary of ordinary vent activities at Stromboli (and what it tells us about vent conditions)

Science.gov (United States)

Gaudin, Damien; Taddeucci, Jacopo; Scarlato, Piergiorgio

2015-04-01

Normal active degassing at Stromboli (Aeolian Islands, Italy) is traditionally divided in two classes. Puffing correspond to the frequent (~1 Hz) release of small gas pockets (0.5 - 1 m of diameter) at low exit velocities (5 - 15 m/s). Whereas, Strombolian explosions occur at a frequency of 1 - 10 per hour, and are characterized the ejection of bombs and/or ash at high velocities (50 - 400 m/s). In order to get a broader overview of two types of degassing, we used a thermal high speed FLIR SC655 camera to monitor the temperature anomalies generated by the expelled gas, ash, and/or bombs. The enhanced time and spatial resolutions of the camera (200 frames per second, 15 cm wide pixels) enables to use numerical algorithms to distinguish and characterize individual ejection events. In particular, for each explosion and puff, we compute the temperature, the volume, the exit point and the rise velocities of the expelled material. These values, as well as the frequency of the release events, are used to portray a total of 12 vent activities, observed during three field campaigns in 2012, 2013 and 2014. Sustained puffing was visible on 7 cases, with an intensity ranging on at least two orders of magnitude. Although the released gas volume is sometimes highly variable, on some cases, constant sized puffs allows to define a typical discharge frequency ranging between 0.4 and 1.5 Hz. Regular Strombolian explosions, with various duration, intensity and ash contents, are reported in 6 cases, 2 of them simultaneously presenting a puffing activity. In some cases, we noticed modifications of the vent activity just before the explosions. These precursors, usually lasting about 1 second but occasionally reaching 10 seconds, can be sorted into 1) increase of the puffing activity ; 2) emission of gas plumes ; 3) inflation of the visible vent surface. Finally, one vent activity was hybrid between puffing and Strombolian explosions, with frequent explosions (1 Hz) ejecting numerous

A COMPARATIVE STUDY OF LATERAL SPHINCTEROTOMY AND LOCAL APPLICATION OF 2% DILTIAZEM GEL IN TREATMENT OF CHRONIC ANAL FISSURE

Directory of Open Access Journals (Sweden)

Rajashekar

2015-11-01

Full Text Available BACKGROUND AND OBJECTIVES Anal fissures are commonly encountered in routine colorectal practice. Chronic fissures have traditionally been treated surgically. Developments in the pharmacological understanding of the internal anal sphincter have resulted in more conservative approaches towards treatment. In this study, we compare topical 2% Diltiazem gel and lateral internal sphincterotomy with respect to symptomatic relief, healing and side effects in the treatment of chronic fissure in ano. METHODS 60 patients with chronic fissure in ano were randomly divided into Diltiazem gel and internal sphincterotomy groups. Patients were followed up at weekly intervals for minimum of eight weeks. Data was recorded accordingly. RESULTS Fissure completely healed in 28(93.33% out of 30 patients treated with 2% Diltiazem gel between 4-8 weeks. Healing was 100% with internal sphincterotomy. The mean duration required for healing of fissure was 4.86 weeks in Diltiazem gel group and 3.66 weeks in internal sphincterotomy group. 61.5% patients were free from pain after treatment with Diltiazem gel whereas in internal sphicterotomy group 66.66% patients had pain relief at the end of 4 weeks. INTERPRETATION AND CONCLUSION Comparison between Diltiazem gel application and internal sphincterotomy did not show any significant difference in fissure healing and pain relief. No side effects were seen in Diltiazem gel therapy. Topical Diltiazem should be the initial treatment in chronic fissure in ano. It is better to reserve internal sphincterotomy for patients with relapse or therapeutic failure to prior pharmacological treatment.

The movement of solutes through aqueous fissures in porous rock

International Nuclear Information System (INIS)

Glueckauf, E.

1980-06-01

A mathematical treatment has been given for the movement of materials dissolved in water flowing through narrow fissures of a micro-porous substrate. As there is no water flow in these micro-pores, equilibrium between the aqueous solution and the micro-porous substrate proceeds only by diffusion, with the result that there arises a gross disequilibrium. Two major effects arise: first, the hold-up in the substrate - even when there is no adsorption taking place - is orders of magnitude larger than on non-porous substrate, and increases even further, if adsorption takes place. Secondly, dispersion caused by non-equilibrium is also orders of magnitude greater than dispersion arising from convection effects of the water flow in interconnecting fissures. As a result, the solutes arrive very much later at the end of the underground fissures, and in concentrations which are very much lower than have been calculated in previous modelling experiments. The significance of these effects is discussed in detail, and this can be helpful in the selection of sites for underground disposal of radioactive waste. It is now quite feasible to specify sites with conditions, where even solutes with minimal adsorption would not return to the surface within a million years, and where solutes of moderately strong adsorption would be effectively immobile. (author)

Modelling hydrothermal venting in volcanic sedimentary basins: Impact on hydrocarbon maturation and paleoclimate

Science.gov (United States)

Iyer, Karthik; Schmid, Daniel W.; Planke, Sverre; Millett, John

2017-06-01

Vent structures are intimately associated with sill intrusions in sedimentary basins globally and are thought to have been formed contemporaneously due to overpressure generated by gas generation during thermogenic breakdown of kerogen or boiling of water. Methane and other gases generated during this process may have driven catastrophic climate change in the geological past. In this study, we present a 2D FEM/FVM model that accounts for 'explosive' vent formation by fracturing of the host rock based on a case study in the Harstad Basin, offshore Norway. Overpressure generated by gas release during kerogen breakdown in the sill thermal aureole causes fracture formation. Fluid focusing and overpressure migration towards the sill tips results in vent formation after only few tens of years. The size of the vent depends on the region of overpressure accessed by the sill tip. Overpressure migration occurs in self-propagating waves before dissipating at the surface. The amount of methane generated in the system depends on TOC content and also on the type of kerogen present in the host rock. Generated methane moves with the fluids and vents at the surface through a single, large vent structure at the main sill tip matching first-order observations. Violent degassing takes place within the first couple of hundred years and occurs in bursts corresponding to the timing of overpressure waves. The amount of methane vented through a single vent is only a fraction (between 5 and 16%) of the methane generated at depth. Upscaling to the Vøring and Møre Basins, which are a part of the North Atlantic Igneous Province, and using realistic host rock carbon content and kerogen values results in a smaller amount of methane vented than previously estimated for the PETM. Our study, therefore, suggests that the negative carbon isotope excursion (CIE) observed in the fossil record could not have been caused by intrusions within the Vøring and Møre Basins alone and that a contribution

Review of containment vent filter technology

International Nuclear Information System (INIS)

Kovach, J.L.

1989-01-01

The technology applied for the design and construction of containment vent filters is compiled and reviewed. The national positions leading to the selection of venting or method of filtration are extracted from position papers. Several areas of further information needs are identified

Sonar backscatter differentiation of dominant macrohabitat types in a hydrothermal vent field.

Science.gov (United States)

Durand, Sébastien; Legendre, Pierre; Juniper, S Kim

2006-08-01

Over the past 20 years, sonar remote sensing has opened ways of acquiring new spatial information on seafloor habitat and ecosystem properties. While some researchers are presently working to improve sonar methods so that broad-scale high-definition surveys can be effectively conducted for management purposes, others are trying to use these surveying techniques in more local areas. Because ecosystem management is scale-dependent, there is a need to acquire spatiotemporal knowledge over various scales to bridge the gap between already-acquired point-source data and information available at broader scales. Using a 675-kHz single-pencil-beam sonar mounted on the remotely operated vehicle ROPOS, 2200 m deep on the Juan de Fuca Ridge, East Pacific Rise, five dominant habitat types located in a hydrothermal vent field were identified and characterized by their sonar signatures. The data, collected at different altitudes from 1 to 10 m above the seafloor, were depth-normalized. We compared three ways of handling the echoes embedded in the backscatters to detect and differentiate the five habitat types; we examined the influence of footprint size on the discrimination capacity of the three methods; and we identified key variables, derived from echoes that characterize each habitat type. The first method used a set of variables describing echo shapes, and the second method used as variables the power intensity values found within the echoes, whereas the last method combined all these variables. Canonical discriminant analysis was used to discriminate among the five habitat types using the three methods. The discriminant models were constructed using 70% of the data while the remaining 30% were used for validation. The results showed that footprints 20-30 cm in diameter included a sufficient amount of spatial variation to make the sonar signatures sensitive to the habitat types, producing on average 82% correct classification. Smaller footprints produced lower percentages of

Homogeneity and fissure determination in uranium bars with solid state nuclear track detectors

Energy Technology Data Exchange (ETDEWEB)

Castillo, F. (Universidad Nacional Autonoma de Mexico, Mexico City. Facultad de Ciencias); Gamboa, I.; Espinosa, G.; Tapia, A. (Universidad Nacional Autonoma de Mexico, Mexico City. Inst. de Fisica); Somogyi, G. (Magyar Tudomanyos Akademia, Debrecen. Atommag Kutato Intezete)

1984-01-01

A simple and efficient method for determining fissure and concentration inhomogeneity in uranium bars is the alpha-radiographic technique. In our present work uranium bars made by ININ (Mexico) were studied by using CR-39 track detectors. The space inhomogeneity in track density was measured by an optical densitometer. The presence of fissure is determined by a microfiche reader. Such a study takes only few hours and does not require sophisticated instrumentation.

Vented Capacitor

Science.gov (United States)

Brubaker, Michael Allen; Hosking, Terry Alan

2006-04-11

A technique of increasing the corona inception voltage (CIV), and thereby increasing the operating voltage, of film/foil capacitors is described. Intentional venting of the capacitor encapsulation improves the corona inception voltage by allowing internal voids to equilibrate with the ambient environment.

Different scale land subsidence and ground fissure monitoring with multiple InSAR techniques over Fenwei basin, China

Directory of Open Access Journals (Sweden)

C. Zhao

2015-11-01

Full Text Available Fenwei basin, China, composed by several sub-basins, has been suffering severe geo-hazards in last 60 years, including large scale land subsidence and small scale ground fissure, which caused serious infrastructure damages and property losses. In this paper, we apply different InSAR techniques with different SAR data to monitor these hazards. Firstly, combined small baseline subset (SBAS InSAR method and persistent scatterers (PS InSAR method is used to multi-track Envisat ASAR data to retrieve the large scale land subsidence covering entire Fenwei basin, from which different land subsidence magnitudes are analyzed of different sub-basins. Secondly, PS-InSAR method is used to monitor the small scale ground fissure deformation in Yuncheng basin, where different spatial deformation gradient can be clearly discovered. Lastly, different track SAR data are contributed to retrieve two-dimensional deformation in both land subsidence and ground fissure region, Xi'an, China, which can be benefitial to explain the occurrence of ground fissure and the correlation between land subsidence and ground fissure.

influence of drying temperature and storage duration on fissuring

African Journals Online (AJOL)

User

age duration on the cracking behaviour and head rice yield of a local rice variety - Jasmine 85. ... harvesting, processing and storage. The rice industry ... cm deep which is within the thickness consid- ered as a ..... Tracing fissure information by.

A comparison between three different pit and fissure sealants with regard to marginal integrity.

Science.gov (United States)

Fernandes, Kristlee Sabrin; Chalakkal, Paul; de Ataide, Ida de Noronha; Pavaskar, Rajdeep; Fernandes, Precylia Philo; Soni, Harleen

2012-04-01

THE AIM OF THIS STUDY IS TO COMPARE THE OCCURRENCE OF ENAMEL FRACTURES, SEALANT FRACTURES AND MARGINAL FISSURES AFTER PLACEMENT OF THREE SEALANTS: Helioseal F, Conseal F and Clinpro. Thirty individuals between 13 and 15 years of age, diagnosed with pit and fissure caries by visual and DIAGNOdent examination, were chosen for sealant placement on their mandibular molars. The sealants were placed at random, after which, impressions were made with polyvinyl siloxane and casts were fabricated. Dies were prepared, each of which were sputter coated with gold in order to be examined under a scanning electron microscope. The following morphologies were analyzed from dies from each of the sealant groups: Continuous margins, sealant fractures, marginal fissures and enamel fractures. After six months, they were recalled for impression making. Dies were prepared and microscopically analyzed as mentioned. Based on the time of evaluation, there were two groups: Initial group (soon after placement) and final group (after six months). Statistical analysis was done using the paired 't' test and One-way analysis of variance (ANOVA). Clinpro had the greatest fracture resistance, followed by Conseal F and Helioseal F. The occurrence of marginal fissure was found to be least with Clinpro.

An Experimental and Numerical Study on Cracking Behavior of Brittle Sandstone Containing Two Non-coplanar Fissures Under Uniaxial Compression

Science.gov (United States)

Yang, Sheng-Qi; Tian, Wen-Ling; Huang, Yan-Hua; Ranjith, P. G.; Ju, Yang

2016-04-01

To understand the fracture mechanism in all kinds of rock engineering, it is important to investigate the fracture evolution behavior of pre-fissured rock. In this research, we conducted uniaxial compression experiments to evaluate the influence of ligament angle on the strength, deformability, and fracture coalescence behavior of rectangular prismatic specimens (80 × 160 × 30 mm) of brittle sandstone containing two non-coplanar fissures. The experimental results show that the peak strength of sandstone containing two non-coplanar fissures depends on the ligament angle, but the elastic modulus is not closely related to the ligament angle. With the increase of ligament angle, the peak strength decreased at a ligament angle of 60°, before increasing up to our maximum ligament angle of 120°. Crack initiation, propagation, and coalescence were all observed and characterized from the inner and outer tips of pre-existing non-coplanar fissures using photographic monitoring. Based on the results, the sequence of crack evolution in sandstone containing two non-coplanar fissures was analyzed in detail. In order to fully understand the crack evolution mechanism of brittle sandstone, numerical simulations using PFC2D were performed for specimens containing two non-coplanar fissures under uniaxial compression. The results are in good agreement with the experimental results. By analyzing the stress field, the crack evolution mechanism in brittle sandstone containing two non-coplanar fissures under uniaxial compression is revealed. These experimental and numerical results are expected to improve the understanding of the unstable fracture mechanism of fissured rock engineering structures.

33 CFR 183.520 - Fuel tank vent systems.

Science.gov (United States)

2010-07-01

...) BOATING SAFETY BOATS AND ASSOCIATED EQUIPMENT Fuel Systems Equipment Standards § 183.520 Fuel tank vent systems. (a) Each fuel tank must have a vent system that prevents pressure in the tank from exceeding 80... 33 Navigation and Navigable Waters 2 2010-07-01 2010-07-01 false Fuel tank vent systems. 183.520...

Clinical Evaluation of applying a hydrophobic and a hydrophilic bonding agent on the retention and durability of fissure sealant therapy

Directory of Open Access Journals (Sweden)

Mostafa GHandi

2016-03-01

Full Text Available Background and Aims: As in fissure sealant therapy the tooth surface is mostly enamel, the use of an enamel bonding agent (hydrophobic bonding agent may be more cost effective than that of newer generations of bonding (hydrophilic bonding agents. The aim of this study was to compare the retention and durability of fissure sealant therapy when applying an enamel bonding agent, a dentin bonding agent and no bonding agent during 4 years. Materials and Methods: This study was done on the first permanent molars of the upper and lower jaws of 24 students of the first grade of a primary school (6-7 years old. On 36 teeth, a dentin bonding agent (Excite was applied under the fissure sealant and on 36 teeth an enamel bonding agent (Margin bond was applied under the fissure sealant. Then, 24 teeth were selected from these two groups and were compared with a group (including 24 teeth with no bonding agent under the fissure sealant (as control group. All the fissures of the teeth were evaluated annually for 4 years to find out the presence or absence of fissure sealant substance. Data were analyzed using Wilcoxon test. Results: From the statistical analysis, there was no significant difference in retention and durability of the fissure sealant substance comparing the group with dentin bonding agent (Excite and the group with enamel bonding agent (Margin bond. Also, using a bonding agent made no significant difference (P>0.05. Conclusion: According to the results of this study, using a bonding agent made no improvement in the retention and durability of fissure sealant substance.

Feasibility and Safety Assessment for Advanced Reactor Concepts Using Vented Fuel

International Nuclear Information System (INIS)

Klein, Andrew; Lenhof, Renae; Deason, Wesley; Harter, Jackson

2015-01-01

Recent interest in fast reactor technology has led to renewed analysis of past reactor concepts such as Gas Fast Reactors and Sodium Fast Reactors. In an effort to make these reactors more economic, the fuel is required to stay in the reactor for extended periods of time; the longer the fuel stays within the core, the more fertile material is converted into usable fissile material. However, as burnup of the fuel-rod increases, so does the internal pressure buildup due to gaseous fission products. In order to reach the 30 year lifetime requirements of some reactor designs, the fuel pins must have a vented-type design to allow the buildup of fission products to escape. The present work aims to progress the understanding of the feasibility and safety issues related to gas reactors that incorporate vented fuel. The work was separated into three different work-scopes: 1. Quantitatively determine fission gas release from uranium carbide in a representative helium cooled fast reactor; 2. Model the fission gas behavior, transport, and collection in a Fission Product Vent System; and, 3. Perform a safety analysis of the Fission Product Vent System. Each task relied on results from the previous task, culminating in a limited scope Probabilistic Risk Assessment (PRA) of the Fission Product Vent System. Within each task, many key parameters lack the fidelity needed for comprehensive or accurate analysis. In the process of completing each task, the data or methods that were lacking were identified and compiled in a Gap Analysis included at the end of the report.

Feasibility and Safety Assessment for Advanced Reactor Concepts Using Vented Fuel

Energy Technology Data Exchange (ETDEWEB)

Klein, Andrew [Oregon State Univ., Corvallis, OR (United States). Nuclear Engineering and Radiation Health Physics; Matthews, Topher [Oregon State Univ., Corvallis, OR (United States); Lenhof, Renae [Oregon State Univ., Corvallis, OR (United States); Deason, Wesley [Oregon State Univ., Corvallis, OR (United States); Harter, Jackson [Oregon State Univ., Corvallis, OR (United States)

2015-01-16

Recent interest in fast reactor technology has led to renewed analysis of past reactor concepts such as Gas Fast Reactors and Sodium Fast Reactors. In an effort to make these reactors more economic, the fuel is required to stay in the reactor for extended periods of time; the longer the fuel stays within the core, the more fertile material is converted into usable fissile material. However, as burnup of the fuel-rod increases, so does the internal pressure buildup due to gaseous fission products. In order to reach the 30 year lifetime requirements of some reactor designs, the fuel pins must have a vented-type design to allow the buildup of fission products to escape. The present work aims to progress the understanding of the feasibility and safety issues related to gas reactors that incorporate vented fuel. The work was separated into three different work-scopes: 1. Quantitatively determine fission gas release from uranium carbide in a representative helium cooled fast reactor; 2. Model the fission gas behavior, transport, and collection in a Fission Product Vent System; and, 3. Perform a safety analysis of the Fission Product Vent System. Each task relied on results from the previous task, culminating in a limited scope Probabilistic Risk Assessment (PRA) of the Fission Product Vent System. Within each task, many key parameters lack the fidelity needed for comprehensive or accurate analysis. In the process of completing each task, the data or methods that were lacking were identified and compiled in a Gap Analysis included at the end of the report.

Containment venting sliding pressure venting process for PWR and BWR plants

International Nuclear Information System (INIS)

Eckardt, B.

1991-01-01

In order to reduce the residual risk associated with hypothetical severe nuclear accidents, nuclear power plants in Germany as well as in certain other European countries have been or will be backfitted with a system for filtered containment venting. During venting system process design, particular importance is attached to the requirements regarding, for example, high aerosol loading capability, provision for decay heat removal from the scrubber unit, the aerosol spectrum to be retained and entirely passive functioning of the scrubber unit. The aerosol spectrum relevant for process design and testing varies depending on aerosol concentrations, the time at which venting is commenced and whether there is an upstream wetwell, etc. Because of this the Reactor Safety Commission in Germany has specified that SnO 2 with a mass mean diameter of approximately 0.5 μm should be used as an enveloping test aerosol. To meet the above-mentioned requirements, a combined venturi scrubber system was developed which comprises a venturi section and a filter demister section and is operated in the sliding pressure mode. This scrubber system was tested using a full-scale model and has now been installed in 14 PWR and BWR plants in Germany and Finland

Tracer movement in a single fissure in granitic rock - some experimental results and their interpretation

International Nuclear Information System (INIS)

Neretnieks, I.; Eriksen, T.; Taetinen, P.

1980-08-01

Radionuclide migration was studied in a natural fissure in a granite core. The fissure was oriented parallel to the axis in a cylindrical core 30 cm long and 20 in diameter. The traced solution was injected at one end of the core and collected at the other. Breakthrough curves were obtained for the nonsorbing tracers tritiated water, and a large molecular weight lignosulphonate molecule and the sorbing tracers cesium and strontium. From the breakthrough curves for the nonsorbing tracers it could be concluded that channeling occurs in the single fissure. A 'dispersion' model based on channeling is presented. The results from the sorbing tracers indicate that there is substantial diffusion into and sorption in the rock matrix. Sorption on the surface of the fissure also accounts for a part of the retardation effect of the sorbing species. A model which includes the mechanisms of channeling, surface sorption matrix diffusion and matrix sorption is presented. The experimental breakthrough curves can be fitted fairly well by this model by use of independently obtained data on diffusivities and matrix sorption. (author)

Tracer Movement in a Single Fissure in Granitic Rock: Some Experimental Results and Their Interpretation

Science.gov (United States)

Neretnieks, Ivars; Eriksen, Tryggve; TäHtinen, PäIvi

1982-08-01

Radionuclide migration was studied in a natural fissure in a granite core. The fissure was oriented parallel to the axis in a cylindrical core 30 cm long and 20 cm in diameter. The traced solution was injected at one end of the core and collected at the other. Breakthrough curves were obtained for the nonsorbing tracers, tritiated water, and a large-molecular-weight lignosulphonate molecule and for the sorbing tracers, cesium and strontium. From the breakthrough curves for the nonsorbing tracers it could be concluded that channeling occurs in the single fissure. A `dispersion' model based on channeling is presented. The results from the sorbing tracers indicate that there is substantial diffusion into and sorption in the rock matrix. Sorption on the surface of the fissure also accounts for a part of the retardation effect of the sorbing species. A model which includes the mechanisms of channeling, surface sorption, matrix diffusion, and matrix sorption is presented. The experimental breakthrough curves can be fitted fairly well by this model by use of independently obtained data on diffusivities and matrix sorption.

Comparative study of resin sealant and resin modified glass ionomer as pit and fissure sealant

Directory of Open Access Journals (Sweden)

Shirin Malek

2017-02-01

Full Text Available The purpose of the present study was to compare the marginal integrity of resin modified glass ionomer cement with that of resin sealant, in vitro. Forty artificial pit and fissure cavities were prepared in occlusal surface of extracted premolar teeth by using ¼ round carbide bur. Cavities were condensed with artificial organic debris followed by cleaning with prophylaxis pumice brush and paste and then separated into two treatment groups. In Group A, 15 fissure cavities were sealed by resin sealant and in Group B, 15 fissure cavities were sealed by resin modified glass ionomer sealant. These specimens were subjected to thermo-cycling followed by dye penetration test. The remaining 5 cavities from each group were analyzed for debris score by the SEM. The results of the microleakage test showed that the efficacy of preventing microleakage of samples sealed by resin modified glass ionomer sealant was higher than the samples sealed by resin sealant. However, no significant differences were found. It can be concluded that use of resin modified glass ionomer sealant is a good alternative for sealing pits and fissures.

Skin hydration of the heel with fissure in patients with diabetes: a cross-sectional observational study

Directory of Open Access Journals (Sweden)

Oe M

2018-06-01

Full Text Available Makoto Oe,1 Kimie Takehara,2 Hiroshi Noguchi,3 Yumiko Ohashi,4 Mayu Fukuda,1 Takashi Kadowaki,5 Hiromi Sanada1,6 1Global Nursing Research Center, 2Department of Advanced Nursing Technology, 3Department of Life Support Technology (Molten, Graduate School of Medicine, The University of Tokyo, 4Department of Nursing, The University of Tokyo Hospital, 5Department of Diabetes and Metabolic Diseases, 6Department of Gerontological Nursing/Wound Care Management, Graduate School of Medicine, The University of Tokyo, Tokyo, Japan Purpose: Foot fissure should be prevented in patients with diabetes due to the likelihood of subsequent diabetic ulcer. The purpose of this study was to investigate a cutoff point for skin hydration with fissure and the factors associated with low skin hydration in patients with diabetes. Subjects and methods: Subjects were patients with diabetes who visited the diabetic foot clinic and were evaluated for skin hydration on the heel between April 2008 and March 2015. Information about fissure, skin hydration, age, sex, autonomic neuropathy, angiopathy, and tinea pedis were collected from the medical charts. Skin hydration on the heel was measured using a moisture checker. Skin hydration was compared between heels with and without fissure, and a cutoff for skin hydration with fissure was determined using receiver operating characteristic analysis. Based on the determined cutoff, factors associated with lower skin hydration were analyzed using logistic regression analysis. Results: Participants comprised 693 patients. Mean±SD age was 66.8±10.8 years, and 57.0% of subjects were male. The frequency of fissures on the heels was 10.4%. Area under the receiver operating characteristic curve for skin hydration in the presence of fissure was 0.717. Twenty percent was selected as the cutoff point, offering sensitivity of 0.478 and specificity of 0.819. Logistic regression analysis showed correlations between three factors (male sex, tinea

46 CFR 56.50-85 - Tank-vent piping.

Science.gov (United States)

2010-10-01

... of the tanks to vent pipes. (2) Tanks having a comparatively small surface, such as fuel oil settling... 46 Shipping 2 2010-10-01 2010-10-01 false Tank-vent piping. 56.50-85 Section 56.50-85 Shipping... APPURTENANCES Design Requirements Pertaining to Specific Systems § 56.50-85 Tank-vent piping. (a) This section...

ANALYSIS OF VENTING OF A RESIN SLURRY

Energy Technology Data Exchange (ETDEWEB)

Laurinat, J.; Hensel, S.

2012-03-27

A resin slurry venting analysis was conducted to address safety issues associated with overpressurization of ion exchange columns used in the Purex process at the Savannah River Site (SRS). If flow to these columns were inadvertently interrupted, an exothermic runaway reaction could occur between the ion exchange resin and the nitric acid used in the feed stream. The nitric acid-resin reaction generates significant quantities of noncondensable gases, which would pressurize the column. To prevent the column from rupturing during such events, rupture disks are installed on the column vent lines. The venting analysis models accelerating rate calorimeter (ARC) tests and data from tests that were performed in a vented test vessel with a rupture disk. The tests showed that the pressure inside the test vessel continued to increase after the rupture disk opened, though at a slower rate than prior to the rupture. Calculated maximum discharge rates for the resin venting tests exceeded the measured rates of gas generation, so the vent size was sufficient to relieve the pressure in the test vessel if the vent flow rate was constant. The increase in the vessel pressure is modeled as a transient phenomenon associated with expansion of the resin slurry/gas mixture upon rupture of the disk. It is postulated that the maximum pressure at the end of this expansion is limited by energy minimization to approximately 1.5 times the rupture disk burst pressure. The magnitude of this pressure increase is consistent with the measured pressure transients. The results of this analysis demonstrate the need to allow for a margin between the design pressure and the rupture disk burst pressure in similar applications.

A 1-year clinical evaluation of fissure sealants on permanent first molars

Directory of Open Access Journals (Sweden)

Nupur Ninawe

2012-01-01

Full Text Available Objective : To evaluate and compare the retention, marginal discoloration, surface texture and anatomical form of pit and fissure sealants. Materials and Methods : Thirty children between the ages of 6 and 10 years, who were attending the school health program regularly, had participated in the study. A split-mouth design was used in which the two fissure sealants (Helioseal-F and Glass ionomer Fuji VII were randomly placed in 60 matched contralateral pairs of permanent molar teeth. Sealants were rated by a single trained and calibrated examiner using mouth mirrors and probes following the US Public Health Service criteria. The sealants were evaluated at 3 months, 6 months and 1 year intervals. Results : The data obtained for retention, marginal discoloration, surface texture and anatomical form of pit and fissure sealants were tabulated and compared statistically using the Chi-square test of significance. Conclusion : The Helioseal-F sealant was better than the Glass ionomer Fuji VII sealant with respect to retention, anatomical form and surface texture. Both the materials showed similar results with respect to marginal discoloration.

Diversity and distribution of microbes in deep-sea sub-vent systems, using newly designed in situ growth chambers

Science.gov (United States)

Higashi, Y.; Sunamura, M.; Utsumi, M.; Urabe, T.; Maruyama, A.

2004-12-01

Subsurface of deep-sea hydrothermal vent environments is one of the most difficult fields on the Earth to approach and collect reliable samples for microbiological study. In our Archaean Park project, we developed in situ incubation instruments to directly collect microbes from sub-vent fields through a drilled borehole. After excavation using a portable submarine driller (BMS) around deep-sea hydrothermal vents in the Suiyo Seamount on the Izu-Bonin Arc (2001, 2002) and the South Mariana (2003), microbial diversity was examined in samples collected from the boreholes, as well as natural vents, using catheter- and column-type in situ growth chambers. In the catheter samples collected from the Suiyo Seamount, several novel phylotypes of microbial SSU rRNA genes were assigned within epsilon-Proteobacteria and hyperthermophile-related Euryarchaea groups. The former novel epsilon group (SSSV-BE1) was also detected in the South Mariana, but they only appeared in the catheter samples collected just below the venting seafloor. These suggest that the group must be significant in warm, shallow and microaerobic sub-vent layers over the sea, at least in the northwest Pacific Ocean. The column-type in situ growth chamber was specially designed for creating and maintaining physico-chemical gradients in a ca. 40-cm-long column situated on an active vent. In Suiyo Seamount samples (vent temp.: ca. 30-100 degree C), a unique vertical profile was found in the diversity of Archaea. At the column bottom, most of the clones were assigned to be members within the lithoautotrophic thermophilic Ignicoccus, while heterotrophic thermophilic Thermococcus were abundant at the column top. Similar vertical profile has also been appeared in the column samples from the South Mariana. Further quantitative population analysis is now under going using these samples. Our approach to the sub-vent biosphere by the combination of drilling and in situ incubation is almost sure to give us important clues

Utility of Indocyanine Green Video Angiography for Sylvian Fissure Dissection in Subarachnoid Hemorrhage Patients - Sylvian ICG Technique.

Science.gov (United States)

Toi, Hiroyuki; Matsushita, Nobuhisa; Ogawa, Yukari; Kinoshita, Keita; Satoh, Kohei; Takai, Hiroki; Hirai, Satoshi; Hara, Keijiro; Matsubara, Shunji; Uno, Masaaki

2018-02-15

Indocyanine green (ICG) emits fluorescence in the far-red domain under light excitation. ICG video angiography (ICG-VA) has been established as a useful method to evaluate blood flow in the operative field. We report the usefulness of ICG-VA for Sylvian fissure dissection in patients with subarachnoid hemorrhage (SAH). Subjects comprised 7 patients who underwent ICG-VA before opening the Sylvian fissure during neck clipping for ruptured cerebral aneurysm. We observed contrasted Sylvian veins before opening the Sylvian fissure using surgical microscopes. This procedure was termed "Sylvian ICG". We observed ICG fluorescence quickly in all cases. Sylvian veins that appeared unclear in the standard microscopic operative field covered with subarachnoid hemorrhage were extremely clearly depicted. These Sylvian ICG findings were helpful in identifying entry points and the dissecting course of the Sylvian fissure. At the time of clipping, no residual fluorescence from Sylvian ICG was present, and aneurysm clipping was not impeded. Sylvian ICG for SAH patients is a novel technique to facilitate dissection of the Sylvian fissure. We believe that this technique will contribute to improved safety of clipping surgery for ruptured aneurysms.

Monitoring arrangement for vented nuclear fuel elements

International Nuclear Information System (INIS)

Campana, R.J.

1981-01-01

In a nuclear fuel reactor core, fuel elements are arranged in a closely packed hexagonal configuration, each fuel element having diametrically opposed vents permitting 180 0 rotation of the fuel elements to counteract bowing. A grid plate engages the fuel elements and forms passages for communicating sets of three, four or six individual vents with respective monitor lines in order to communicate vented radioactive gases from the fuel elements to suitable monitor means in a manner readily permitting detection of leakage in individual fuel elements

Maintenir la continuité des collections à l'heure d'Internet : du catalogue de vente au site web de maison de vente

OpenAIRE

Jacquet , Françoise

2014-01-01

International audience; La Bibliothèque nationale de France conserve depuis des siècles une importante collection de catalogues de vente sur support papier. Cependant avec l’apparition d’Internet on assiste à une dématérialisation des données documentaires en art. Aujourd’hui les sites des maisons de vente offrent en ligne les adjudications des ventes, récentes ou archivées et certaines ventes sont désormais annoncées uniquement sur Internet. Ces informations qui ne se trouvent pas sur les ca...

Hydrogen is an energy source for hydrothermal vent symbioses.

Science.gov (United States)

Petersen, Jillian M; Zielinski, Frank U; Pape, Thomas; Seifert, Richard; Moraru, Cristina; Amann, Rudolf; Hourdez, Stephane; Girguis, Peter R; Wankel, Scott D; Barbe, Valerie; Pelletier, Eric; Fink, Dennis; Borowski, Christian; Bach, Wolfgang; Dubilier, Nicole

2011-08-10

The discovery of deep-sea hydrothermal vents in 1977 revolutionized our understanding of the energy sources that fuel primary productivity on Earth. Hydrothermal vent ecosystems are dominated by animals that live in symbiosis with chemosynthetic bacteria. So far, only two energy sources have been shown to power chemosynthetic symbioses: reduced sulphur compounds and methane. Using metagenome sequencing, single-gene fluorescence in situ hybridization, immunohistochemistry, shipboard incubations and in situ mass spectrometry, we show here that the symbionts of the hydrothermal vent mussel Bathymodiolus from the Mid-Atlantic Ridge use hydrogen to power primary production. In addition, we show that the symbionts of Bathymodiolus mussels from Pacific vents have hupL, the key gene for hydrogen oxidation. Furthermore, the symbionts of other vent animals such as the tubeworm Riftia pachyptila and the shrimp Rimicaris exoculata also have hupL. We propose that the ability to use hydrogen as an energy source is widespread in hydrothermal vent symbioses, particularly at sites where hydrogen is abundant.

Can earthquake fissures predispose hillslopes to landslides? - Evidence from Central and East Asia

Science.gov (United States)

Sidle, Roy C.; Gomi, Takashi; Rajapbaev, Muslim; Chyngozhoev, Nurstan

2017-04-01

Factors affecting earthquake-initiated landslides include earthquake magnitude, focal depth, and seismic wave propagation and attenuation. In contrast to rainfall-initiated landslides, earthquake-induced landslides often occur on convex slopes and near ridgelines. Here we present evidence from Fergana Basin, Kyrgyzstan and Kumamoto, Japan on how fissures developed during earthquakes may promote subsequent initiation of rainfall-triggered landslides. More than 1800 recent major landslides in hilly terrain and soft sediments of the Fergana Basin have been largely attributed to accumulation of heavy rainfall and snowmelt. While no large earthquakes have occurred in the Fergana Basin, smaller earthquakes have generated fissures near ridgelines and on convex slopes. The connection of fissures, developed years or decades before slope failure, with preferential transport of rainwater and runoff into the soil has not been previously investigated. Fissures have been observed to expand with time, particularly during subsequent minor earthquakes, further promoting preferential infiltration. Because the soil mantle does not have large contrasts in permeability that would define a slip plane for landslides, it appears that the position and depth of these fissures may control the location and depth of failures. Zones in the soil where surficial inputs of water are preferentially transported, augment natural subsurface accumulation of antecedent rainfall. Many landslides in the eastern Fergana Basin occur after several months of accumulated precipitation and groundwater has been observed emerging on critical hillside locations (near ridgelines and on convex slopes) prior to slope failure. During the 2016 Kumamoto Earthquake (M 7.3), many landslides were triggered in forest and grassland hillslopes near Mount Aso. All of these earthquakes were shallow (focal depths about 10 km), causing high shaking intensity and ground rupturing. Because soils were relatively dry during these

Boiling vapour-type fluids from the Nifonea vent field (New Hebrides Back-Arc, Vanuatu, SW Pacific): Geochemistry of an early-stage, post-eruptive hydrothermal system

Science.gov (United States)

Schmidt, Katja; Garbe-Schönberg, Dieter; Hannington, Mark D.; Anderson, Melissa O.; Bühring, Benjamin; Haase, Karsten; Haruel, Christy; Lupton, John; Koschinsky, Andrea

2017-06-01

In 2013, high-temperature vent fluids were sampled in the Nifonea vent field. This field is located within the caldera of a large shield-type volcano of the Vate Trough, a young extensional rift in the New Hebrides back-arc. Hydrothermal venting occurs as clear and black smoker fluids with temperatures up to 368 °C, the hottest temperatures measured so far in the western Pacific. The physico-chemical conditions place the fluids within the two-phase field of NaCl-H2O, and venting is dominated by vapour phase fluids with Cl concentrations as low as 25 mM. The fluid composition, which differs between the individual vent sites, is interpreted to reflect the specific geochemical fluid signature of a hydrothermal system in its initial, post-eruptive stage. The strong Cl depletion is accompanied by low alkali/Cl ratios compared to more evolved hydrothermal systems, and very high Fe/Cl ratios. The concentrations of REY (180 nM) and As (21 μM) in the most Cl-depleted fluid are among the highest reported so far for submarine hydrothermal fluids, whereas the inter-element REY fractionation is only minor. The fluid signature, which has been described here for the first time in a back-arc setting, is controlled by fast fluid passage through basaltic volcanic rocks, with extremely high water-rock ratios and only limited water-rock exchange, phase separation and segregation, and (at least) two-component fluid mixing. Metals and metalloids are unexpectedly mobile in the vapour phase fluids, and the strong enrichments of Fe, REY, and As highlight the metal transport capacity of low-salinity, low-density vapours at the specific physico-chemical conditions at Nifonea. One possible scenario is that the fluids boiled before the separated vapour phase continued to react with fresh glassy lavas. The mobilization of metals is likely to occur by leaching from fresh glass and grain boundaries and is supported by the high water/rock ratios. The enrichment of B and As is further controlled

40 CFR 63.1408 - Aggregate batch vent stream provisions.

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 11 2010-07-01 2010-07-01 true Aggregate batch vent stream provisions... § 63.1408 Aggregate batch vent stream provisions. (a) Emission standards. Owners or operators of aggregate batch vent streams at a new or existing affected source shall comply with either paragraph (a)(1...

Coil spring venting arrangement

International Nuclear Information System (INIS)

McCugh, R.M.

1975-01-01

A simple venting device for trapped gas pockets in hydraulic systems is inserted through a small access passages, operated remotely, and removed completely. The device comprises a small diameter, closely wound coil spring which is pushed through a guide temporarily inserted in the access passage. The guide has a central passageway which directs the coil spring radially upward into the pocket, so that, with the guide properly positioned for depth and properly oriented, the coil spring can be pushed up into the top of the pocket to vent it. By positioning a seal around the free end of the guide, the spring and guide are removed and the passage is sealed

The effect of different enamel surface treatments on microleakage of fissure sealants

Directory of Open Access Journals (Sweden)

Asli Topaloglu-Ak

2013-11-01

Full Text Available Objective. The aim of this study was to evaluate the effects of different techniques of surface treatment on the microleakage of fissure sealants in permanent molar teeth in vitro. Materials and methods. 96 extracted impacted human third molars were randomly divided into 8 surface treatment groups (n=12/group as 1. Er: YAG laser; (Fidelis II, Fotona, Ljubljana, Slovenia (125 mj, 20Hz. 2. Er: YAG laser + 37% H3PO4 (15s; 3. ER: AG laser + 37% H3PO4+Prime&Bond NT; 4. Er: YAG laser + G Bond; 5. Er: YAG laser + Prime&Bond NT; 6. 37% H3PO4; 7. 37% H3PO4 + Prime &Bond NT; 8. G Bond. Sealant material (Clinpro, 3M ESPE, Seefeld, Germany, was applied into the fissures and light-cured for 20s with LED (Bluephase C5, Ivoclar-Vivadent, Schaan, Liechtenstein. Specimens were subjected to thermocycling (1000×, 5-55°C, dwell time: 15s and immersed in 0.5% basic fuchsin solution for 24h at 37°C. The samples were sectioned and scored on a 3 point rating scale using a light microscope with a magnification of ×20. One-way analysis of variance was used to analyze data. Multiple comparisons were analyzed using Bonferroni test (p=0.05. Results. Er:YAG laser showed the highest microleakage scores whereas Er YAG laser + 37% H3PO4 showed the lowest. Although 37% H3PO4 group showed higher scores than Er:YAG laser + 37% H3PO4, the difference was not statistically significant. Conclusion. Etching fissures with phosphoric acid is sufficient prior to fissure sealant application.

The Lobe Fissure Tracking by the Modified Ant Colony Optimization Framework in CT Images

Directory of Open Access Journals (Sweden)

Chii-Jen Chen

2014-11-01

Full Text Available Chest computed tomography (CT is the most commonly used technique for the inspection of lung lesions. However, the lobe fissures in lung CT is still difficult to observe owing to its imaging structure. Therefore, in this paper, we aimed to develop an efficient tracking framework to extract the lobe fissures by the proposed modified ant colony optimization (ACO algorithm. We used the method of increasing the consistency of pheromone on lobe fissure to improve the accuracy of path tracking. In order to validate the proposed system, we had tested our method in a database from 15 lung patients. In the experiment, the quantitative assessment shows that the proposed ACO method achieved the average F-measures of 80.9% and 82.84% in left and right lungs, respectively. The experiments indicate our method results more satisfied performance, and can help investigators detect lung lesion for further examination.

Natural Treatments for Fissure in Ano Used by Traditional Persian Scholars, Razi (Rhazes) and Ibn Sina (Avicenna).

Science.gov (United States)

Derakhshan, Ali Reza

2016-06-08

Most cases of chronic fissure do not respond to medical treatment. Razi and Ibn Sina were 2 of the best-known scientists of ancient Persia. The purpose of this study was to find out new scientific evidence in modern medicine about their recommendations, in order to find certain clues to conduct useful researches in the future. First, treatments of anal fissure mentioned by Razi and Ibn Sina were reviewed. Then, literature search was made in electronic databases including PubMed, Scopus, and Google Scholar. Management of anal fissure according to Razi's and Ibn Sina's practices is done based on 3 interventions: lifestyle modifications, drug treatments, and manual procedures. Almost all remedies suggested by Razi and Ibn Sina have shown their effects on fissure in ano via several mechanisms of action in many in vitro and in vivo studies; Still there is lack of human studies on the subject. © The Author(s) 2016.

Vents Pattern Analysis at Etna volcano (Sicily, Italy).

Science.gov (United States)

Brancato, Alfonso; Tusa, Giuseppina; Coltelli, Mauro; Proietti, Cristina; Branca, Stefano

2014-05-01

Mount Etna is a composite stratovolcano located along the Ionian coast of eastern Sicily. It is characterized by basaltic eruptions, both effusive and explosive, occurred during a complex eruptive history over the last 500 ka. Flank eruptions occur at an interval of decades, mostly concentrated along the NE, S and W rift zones. A vent clustering at various scales is a common feature in many volcanic settings. In order to identify the clusters within the studied area, a spatial point pattern analysis is undertaken using vent positions, both known and reconstructed. It reveals both clustering and spatial regularity in the Etna region at different distances. The visual inspection of the vent spatial distribution suggests a clustering on the rift zones of Etna volcano. To confirm this evidence, a coarse analysis is performed by the application of Ξ2- and t-test simple statistics. Then, a refined analysis is performed by using the Ripley K-function (Ripley, 1976), whose estimator K(d), knowing the area of the study region and the number of vents, allow us to calculate the distance among two different location of events. The above estimator can be easier transformed by using the Besag L-function (Besag, 1977); the peaks of positive L(d)=[K(d)/π]1/2 -d values indicate clustering while troughs of negative values stand for regularity for their corresponding distances d (L(d)=0 indicates complete spatial randomness). Spatial pattern of flank vents is investigated in order to model the spatial distribution of likely eruptive vents for the next event, basically in terms of relative probabilities. For this, a Gaussian kernel technique is used, and the L(d) function is adopted to generate an optimal smoothing bandwidth based on the clustering behaviour of the Etna volcano. A total of 154 vents (among which 36 are reconstructed), related to Etna flank activity of the last 4.0 ka, is used to model future vent opening. The investigated region covers an area of 850 km2, divided

46 CFR 182.450 - Vent pipes for fuel tanks.

Science.gov (United States)

2010-10-01

... 46 Shipping 7 2010-10-01 2010-10-01 false Vent pipes for fuel tanks. 182.450 Section 182.450... TONS) MACHINERY INSTALLATION Specific Machinery Requirements § 182.450 Vent pipes for fuel tanks. (a) Each unpressurized fuel tank must be fitted with a vent pipe connected to the highest point of the tank...

Comparing the etiology and treatment of skin fissure in traditional and conventional medicine; a brief review

Directory of Open Access Journals (Sweden)

A. Jedkareh

2016-01-01

Full Text Available Dry skin is a common problem which affects wound healing, severity of other skin diseases and quality of life of people. One of its undesirable effects is fissure that is a cutaneous condition in which there is a linear loss of epidermis and dermis with sharply defined, nearly vertical walls. In the present study, we have investigated the etiology of the disease and its treatments in conventional medicine and Iranian Traditional Medicine (ITM. Two traditional medicine references, current scientific data bases and medicinal texts were explored with the selected keywords such as "sheqaq-e-poosti", "skin fissure" and "dry skin" to find the etiology and treatment of skin fissure. From the view point of both conventional medicine and ITM, dry skin is the cause of skin fissure and some causes of dry skin are similar. In conventional medicine, moisturizers are mainly used for treatment of dry skin; while in ITM some herbs, oils and other natural remedies have been used. A topical dosage form which was called "qeirooti", a mixture of wax and oil, was used to treat skin fissure in ITM. It comprised of oily ingredients that acted as occlusives and also some herbal components that directly improved dry skin (similar to moisturizers. Components efficacy of traditional dosage forms for treatment of dry skin lead us to study about formulation of “qeirooti” for treatment of dry skin.

The role of CT and MRI in the assessment of dementia of Alzheimer type

International Nuclear Information System (INIS)

Zhao Hong; Wang Jun; Li Binxiang; Bai Peichen; Ma Jintang

1998-01-01

Purpose: To test the predictive value of atrophy of hippocampal formation (HF) in detecting dementia of Alzheimer type (DAT) patients with CT and MRI. Materials and methods: A total of 30 subjects (13 DAT patients and 17 normal volunteers) were studied with CT. The MR examinations were performed in 13 subjects (8 DAT and 5 normal). The width of choroidal fissure/hippocampal fissure on CT and MR imaging was measured to assess the HF volume. Results: MMSE sensitivity exceeded that of choroidal fissure/hippocampal fissure in DAT patients and the specificity of choroidal fissure/hippocampal fissure was superior to that of MMSE in normal volunteers. A significant correlation (P<0.05) between MMSE score and HF volume was observed in all DAT patients. Conclusion: Dilatation of choroidal fissure/hippocampal fissure and reduction of HF volume were a useful radiologic marker for the diagnosis of DAT

Bacterial Diets of Primary Consumers at Hydrothermal Vents

Science.gov (United States)

Govenar, B.; Shank, T. M.

2008-12-01

Chemical energy produced by mixing hydrothermal fluids and seawater supports dense biological communities on mid-ocean ridges. The base of the food web at deep-sea hydrothermal vents is formed by chemolithoautotrophic bacteria that use the energy from the oxidation of reduced chemicals to fix inorganic carbon into simple sugars. With the exception of a few species that have chemolithoautotropic bacterial symbionts, most of the vent-endemic macrofauna are heterotrophs that feed on free-living bacteria, protists, and other invertebrates. The most abundant and diverse group of primary consumers in hydrothermal vent communities belong to the Gastropoda, particularly the patellomorph limpets. Gastropod densities can be as high as 2000 individuals m-2, and there can be as many as 13 species of gastropods in a single aggregation of the siboglinid tubeworm Riftia pachyptila and more than 40 species along the East Pacific Rise. Some gastropods are ubiquitous and others are found in specific microhabitats, stages of succession, or associated with different foundation species. To determine the mechanisms of species coexistence (e.g. resource partitioning or competition) among hydrothermal vent primary consumers and to track the flow of energy in hydrothermal vent communities, we employed molecular genetic techniques to identify the gut contents of four species of co-occurring hydrothermal vent gastropods, Eulepetopsis vitrea, Lepetodrilus elevatus, Lepetodrilus ovalis and Lepetodrilus pustulosus, collected from a single diffuse-flow hydrothermal vent site on the East Pacific Rise. Unique haplotypes of the 16S gene that fell among the epsilon-proteobacteria were found in the guts of every species, and two species had gut contents that were similar only to epsilon-proteobacteria. Two species had gut contents that also included haplotypes that clustered with delta-proteobacteria, and one species had gut contents that clustered with alpha- proteobacteria. Differences in the diets

Water Stream in Bidet Toilet Commode as a Cause of Anterior Anal Fissure: A Case-Control Study

Directory of Open Access Journals (Sweden)

Pankaj Garg

2017-03-01

Full Text Available Background Water used as a single sharp stream in toilet commode for post defecation cleansing is a common practice in several countries across the globe including India. Repeated hitting of the anus by water stream could potentially cause injury to the anal canal epithelium and lead to development of fissure-in-ano. As the water stream is emanating from the backside of the toilet commode, the possible injury, if any, would be on the anterior anal canal. Objectives The present study aimed at determining whether water stream usage in toilet commodes increased the incidence of anterior fissure-in-ano; this was determined by the incidence of anterior fissure-in-ano the study and control groups. Methods All consecutive fissure-in-ano patients referring to a colorectal clinic from February 2012 to 2015 were included in the study. The patients were classified as a study group (who were using water stream for cleansing purposes in toilet commodes and a control group (patients who were not using water stream. The characteristics and location (position of the fissure-in-ano was noted. Results In this study, 165 patients were prospectively enrolled. Male/female ratio was 96/69, and the mean age was 36.3 ± 11.2 years. The anterior fissure-in-ano in the study group was 55.9% (47/84, while it was 17.3 % (14/81 in the control group (P < 0.0001, odds ratio: 6.08, 95% CI: 2.96 - 12.47]. Conclusions Water used as a single sharp stream to cleanse after defecation in toilet commodes is hazardous and should be avoided.

46 CFR 119.450 - Vent pipes for fuel tanks.

Science.gov (United States)

2010-10-01

... 46 Shipping 4 2010-10-01 2010-10-01 false Vent pipes for fuel tanks. 119.450 Section 119.450... Specific Machinery Requirements § 119.450 Vent pipes for fuel tanks. (a) Each unpressurized fuel tank must... area of the vent pipe for diesel fuel tanks must be as follows: (1) Not less than the cross sectional...

Endobronchial valves in severe emphysematous patients: CT evaluation of lung fissures completeness, treatment radiological response and quantitative emphysema analysis

Energy Technology Data Exchange (ETDEWEB)

Koenigkam-Santos, Marcel, E-mail: marcelk46@yahoo.com.br, E-mail: marcelk46@usp.b [Universidade de Sao Paulo (HCFMRP/USP), Ribeirao Preto, SP (Brazil). Hospital das Clinicas da Faculdade de Medicina; Paula, Wagner Diniz de [University of Brasilia (UnB), DF (Brazil). Brasilia University Hospital; Gompelmann, Daniela [University of Heidelberg (Germany). Department of Pneumology and Respiratory Medicine of the Chest Clinic (Thoraxklinik); Kauczor, Hans-Ulrich [University of Heidelberg (Germany). Department of Diagnostic and Interventional Radiology; Heussel, Claus Peter; Puderbach, Michael [University of Heidelberg (Germany). Department of Diagnostic and Interventional Radiology with Nuclear Medicine of the Chest Clinic (Thoraxklinik)

2013-01-15

Objective: To evaluate lung fissures completeness, post-treatment radiological response and quantitative CT analysis (QCTA) in a population of severe emphysematous patients submitted to endobronchial valves (EBV) implantation. Materials and Methods: Multi-detectors CT exams of 29 patients were studied, using thin-section low dose protocol without contrast. Two radiologists retrospectively reviewed all images in consensus; fissures completeness was estimated in 5% increments and post-EBV radiological response (target lobe atelectasis/volume loss) was evaluated. QCTA was performed in pre and post-treatment scans using a fully automated software. Results: CT response was present in 16/29 patients. In the negative CT response group, all 13 patients presented incomplete fissures, and mean oblique fissures completeness was 72.8%, against 88.3% in the other group. QCTA most significant results showed a reduced post-treatment total lung volume (LV) (mean 542 ml), reduced EBV-submitted LV (700 ml) and reduced emphysema volume (331.4 ml) in the positive response group, which also showed improved functional tests. Conclusion: EBV benefit is most likely in patients who have complete interlobar fissures and develop lobar atelectasis. In patients with no radiological response we observed a higher prevalence of incomplete fissures and a greater degree of incompleteness. The fully automated QCTA detected the post-treatment alterations, especially in the treated lung analysis. (author)

SBWR PCCS vent phenomena and suppression pool mixing

Energy Technology Data Exchange (ETDEWEB)

Coddington, P. [Thermal-Hydraulics Lab., Paul Scherrer Institute, Villigen (Switzerland); Andreani, M. [Nuclear Engineering Lab., Swiss Federal Institute of Technology, Zurich (Switzerland)

1995-09-01

The most important phenomena influencing the effectiveness of the pressure suppression capability of the water pool within the Wetwell compartment of the SBWR Containment, during the period of Passive Containment Cooling System (PCCS) venting, have been critically reviewed. In addition, calculations have been carried-out to determine the condensation of the vented steam and the distribution of the energy deposited in the liquid pool. It has been found that a large contribution to the vapour suppression is due to condensation inside the vent pipe. The condensation rate of the steam inside the bubbles, produced at the vent exit, during their rise to the surface, may however be rather low, because of the large size bubbles. This can lead to vapour channelling to the Wetwell gas space. The above comments are likely to be ameliorated if the vent exit is a distributed source or sparger. Due to the large water flow rates within the {open_quotes}bubbly two-phase plume{close_quotes} generated by the gas injection, the water in the pool above the vent exit is likely to be heated nearly isothermally (perfect mixing). The effect of the suppression pool walls would be to enhance the recirculation and, consequently to promote mixing. The large size of the bubbles therein and of the walls on pool mixing are the most severe difficulties in extrapolating the results from scaled experiments to prototypical conditions.

Newborn with Prenatally Diagnosed Choroidal Fissure Cyst and Panhypopituitarism and Review of the Literature

Directory of Open Access Journals (Sweden)

Ritu Chitkara

2011-12-01

Full Text Available Little has been reported on fetal diagnosis of choroidal fissure cysts and prediction of the clinical complications that can result. We describe the case of a near-term male infant with prenatally diagnosed choroidal fissure cyst and bilateral clubfeet. His prolonged course in the neonatal intensive care nursery was marked by severe panhypopituitarism, late-onset diabetes insipidus, placement of a cystoperitoneal shunt, and episodes of sepsis. Postnatal genetic evaluation also revealed an interstitial deletion involving most of band 10q26.12 and the proximal half of band 10q26.13. The patient had multiple readmissions for medical and surgical indications and died at 6 months of age. This case represents the severe end of the spectrum of medical complications for children with choroidal fissure cysts. It highlights not only the importance of comprehensive evaluation and multidisciplinary management and counseling in such cases, but also the need for heightened vigilance in these patients.

Insights into fluid flow and environmental conditions present in deep-sea hydrothermal vent deposits from measurements of permeability and porosity

Science.gov (United States)

Gribbin, J. L.; Zhu, W.; Tivey, M. K.

2008-12-01

Evolution of permeability-porosity relationships (EPPRs) of different seafloor vent deposit sample types provide crucial information about how fluid flows within the deposits. In this study, we conducted permeability and porosity measurements on a wide range of vent sample types recovered from many different active seafloor vent fields. The sample set includes chalcopyrite-lined black smoker chimneys, Zn-rich diffusing spires (including white smokers), flanges/slabs/crusts (i.e., plate-like deposits that overlie pooled fluid), massive anhydrite, and cores recovered from the sides of vent structures. Using a probe permeameter, permeability measurements were systematically taken of each sample along several orientations. The measured permeability ranges over 6 orders of magnitude from 10-14 to 10-8 m2. Our data indicate that in general massive anhydrite samples are the least permeable with a mean at ~10-13 m2 and the samples from Zn-rich diffusing spires that were actively venting when collected are the most permeable with a mean at ~10-11 m2. With a mean at 10-11.5 m2, permeability data of flanges/slabs/crusts span over 4 orders of magnitude from 10-13 to 10-9 m2, the largest spread among all sample types tested. Permeability values of the outer portions of relict spires, ranging from ~10-13 m2 to 10-9.5 m2, displayed clear anisotropic trends: permeability along the radial directions is higher than that along the axial direction. Black smokers exhibit a strong layered heterogeneity, where inner chalcopyrite linings were significantly less permeable than outermost layers. To conduct porosity and directional permeability measurements, cylindrical cores will be taken from these vent samples. We will examine whether different sample types, or portions of samples, exhibit distinct permeability-porosity relationships, and will then use micro-structural observations of the cores to examine chimney growth processes (e.g., mineral deposition or cracking) that likely result

Characterizing the Morphology, Distribution, and Formation Geometry of Mercury's Pyroclastic Vents

Science.gov (United States)

Jozwiak, L. M.; Head, J. W.; Wilson, L.

2018-05-01

We present a final catalog of pyroclastic vents on Mercury, identifying 104 candidate pyroclastic vents. We then assess the vent distribution, morphologic variation, and probable formation geometries.

Explosion hazards of LPG-air mixtures in vented enclosure with obstacles.

Science.gov (United States)

Zhang, Qi; Wang, Yaxing; Lian, Zhen

2017-07-15

Numerical simulations were performed to study explosion characteristics of liquefied petroleum gas (LPG) explosion in enclosure with a vent. Unlike explosion overpressure and dynamic pressure, explosion temperature of the LPG-air mixture at a given concentration in a vented enclosure has very little variation with obstacle numbers for a given blockage ratio. For an enclosure without obstacle, explosion overpressures for the stoichiometric mixtures and the fuel-lean mixtures reach their maximum within the vent and that for fuel-rich mixture reaches its maximum beyond and near the vent. Dynamic pressures produced by an indoor LPG explosion reach their maximum always beyond the vent no matter obstacles are present or not in the enclosure. A LPG explosion in a vented enclosure with built-in obstacles is strong enough to make the brick and mortar wall with a thickness of 370mm damaged. If there is no obstacle in the enclosure, the lower explosion pressure of several kPa can not break the brick and mortar wall with a thickness of 370mm. For a LPG explosion produced in an enclosure with a vent, main hazards, within the vent, are overpressure and high temperature. However main hazards are dynamic pressure, blast wind, and high temperature beyond the vent. Copyright © 2017 Elsevier B.V. All rights reserved.

A vented pump limiter for the reversed field pinch RFX

International Nuclear Information System (INIS)

Sonato, P.

1998-01-01

The reversed field pinch (RFP) plasma performance, as in the Tokamak, is strongly correlated with the edge neutral particle control. The drawbacks of the conventional magnetic divertors and throat limiters on the RFP plasma have slackened the application of an active particle control system in existing devices. An advanced solution, based on the idea of the 'vented pump limiter' experimented on Tore Supra, has been conceived for RFX. This type of pump limiter is very attractive for a RFP. In this paper, the design of a 'vented limiter' prototype for RFX is presented. Up to six modules of this limiter can be installed at the equatorial plane of RFX, allowing a particle exhaust efficiency comparable with a divertor or a throat limiter working in a Tokamak. Finally, the optimization of this concept for the next step RFP device is presented. (orig.)

Deformation at longyao ground fissure and its surroundings, north China plain, revealed by ALOS PALSAR PS-InSAR

Science.gov (United States)

Yang, Chengsheng; Lu, Zhong; Zhang, Qin; Zhao, Chaoying; Peng, Jianbing; Ji, Lingyun

2018-05-01

The Longyao ground fissure (LGF) is the longest and most active among more than 1000 ground fissures on the North China Plain. There have been many studies on the formation mechanism of the LGF, due to its scientific importance and its potential for damage to the environment. These studies have been based on both regional tectonic analysis and numerical simulations. In order to provide a better understanding of the formation mechanism, the deformation of the crack and its surrounding environment should be taken into consideration. In this paper, PS-InSAR technology was employed to assess the ground deformation of LGF and its surrounding area, using L-band ALOS-1 PALSAR images from 2007 to 2011. The characteristics of ground deformation, relationships between fissure activity and surrounding faults and groundwater exploitation were analyzed. This study shows that the north side of Longyao fault (LF) is uplifting while the south side is subsiding. This provides the tectonic conditions responsible for the activity of the ground fissure. Local groundwater exploitation also plays an important role in the development of ground fissures. InSAR observations were modeled to infer the loading depth (-2.8 km) and the slip rate (31.1 mm/yr) of LF.

Assessment of Literature Related to Combustion Appliance Venting Systems

Energy Technology Data Exchange (ETDEWEB)

Rapp, V. H.; Less, B. D.; Singer, B. C.; Stratton, J. C.; Wray, C. P.

2015-02-01

In many residential building retrofit programs, air tightening to increase energy efficiency is often constrained by safety concerns with naturally vented combustion appliances. Tighter residential buildings more readily depressurize when exhaust equipment is operated, making combustion appliances more prone to backdraft or spill combustion exhaust into the living space. Several measures, such as installation guidelines, vent sizing codes, and combustion safety diagnostics, are in place with the intent to prevent backdrafting and combustion spillage, but the diagnostics conflict and the risk mitigation objective is inconsistent. This literature review summarizes the metrics and diagnostics used to assess combustion safety, documents their technical basis, and investigates their risk mitigations. It compiles information from the following: codes for combustion appliance venting and installation; standards and guidelines for combustion safety diagnostics; research evaluating combustion safety diagnostics; research investigating wind effects on building depressurization and venting; and software for simulating vent system performance.

Analysis of some laboratory tracer runs in natural fissures

International Nuclear Information System (INIS)

Moreno, L.; Neretnieks, I.

1984-01-01

Tracer tests in natural fissures performed in the laboratory are analysed by means of fitting two different models. In the experiments, sorbing and non-sorbing tracers were injected into a natural fissure running parallel to the axis of a drill core. The models take into account advection, diffusion into the rock matrix, sorption onto the rock surface and dispersion. For the last mechanism, one of the models considers hydrodynamic dispersion while the other model assumes channeling dispersion. The models take into account time delays in the inlet and outlet channels. The dispersion characteristics and water residence time were determined from the experiments with non-sorbing tracers. Surface and volume sorption coefficients and data on diffusion into the rock matrix were determined for the sorbing tracers. The results are compared with values independently determined in the laboratory. Good agreement was obtained using either model. When these models are used for prediction of tracer transport over larger distances, the results will depend on the model. The model with channeling dispersion will show a greater dispersion than the model with hydrodynamic dispersion. (author)

Preconsolidation of Søvind Marl - a highly fissured Eocene clay

DEFF Research Database (Denmark)

Grønbech, Gitte Lyng; Ibsen, Lars Bo; Nielsen, Benjaminn Nordahl

2015-01-01

Determination of the preconsolidation stresses is a key tool in geotechnical engineering used to evaluate and estimate the behavior of soils. However, it has been proven difficult to accurately estimate the preconsolidation in highly fissured overconsolidated clays, due to the effect of the fissu...

Clinical effectiveness and cost-effectiveness of fissure sealants in children and adolescents with a high caries risk

Directory of Open Access Journals (Sweden)

Neusser, Silke

2014-10-01

Full Text Available [english] In Germany, the application of resin-based pits and fissures sealants on the occlusal surfaces of permanent molars is part of individual prophylaxis for children and adolescents between six and 18 years. The individual prophylaxis is covered by the Statutory Health Insurance since 1993.The report addresses questions on medical effectiveness, cost-effectiveness, as well as ethical, social, and legal implications of pit and fissure sealants in preventing dental caries for children and adolescents at high caries risk. The results of the studies indicate a protective effect of pit and fissure sealants, particularly for children and adolescents at high caries risk. Additionally, the economic evaluation suggests a tendency for cost savings in this group. Nevertheless, a general expansion of the intervention cannot be recommended. All studies show a risk of bias in favour of pit and fissure sealing and a limited transferability to the German health care system. Studies included in the economic evaluation revealed methodological flaws. Both the economic models and primary studies do not provide reliable results.

King's Bowl Pit Crater, Lava Field and Eruptive Fissure, Idaho - A Multipurpose Volcanic Planetary Analog

Science.gov (United States)

Hughes, S. S.; Garry, B.; Kobs-Nawotniak, S. E.; Sears, D. W. G.; Borg, C.; Elphic, R. C.; Haberle, C. W.; Kobayashi, L.; Lim, D. S. S.; Sears, H.; Skok, J. R.; Heldmann, J. L.

2014-12-01

King's Bowl (KB) and its associated eruptive fissure and lava field on the eastern Snake River Plain, is being investigated by the NASA SSERVI FINESSE (Field Investigations to Enable Solar System Science and Exploration) team as a planetary analog to similar pits on the Moon, Mars and Vesta. The 2,220 ± 100 BP basaltic eruption in Craters of the Moon National Monument and Preserve represents early stages of low shield growth, which was aborted when magma supply was cut off. Compared to mature shields, KB is miniscule, with ~0.02 km3 of lava over ~3 km2, yet the ~6 km long series of fissures, cracks and pits are well-preserved for analog studies of volcanic processes. The termination of eruption was likely related to proximity of the 2,270 ± 50 BP eruption of the much larger Wapi lava field (~5.5 km3 over 325 km2 area) on the same rift. Our investigation extends early work by R. Greeley and colleagues, focusing on imagery, compositional variations, ejecta distribution, dGPS profiles and LiDAR scans of features related to: (1) fissure eruptions - spatter ramparts, cones, feeder dikes, extension cracks; (2) lava lake formation - surface morphology, squeeze-ups, slab pahoehoe lava mounds, lava drain-back, flow lobe overlaps; and (3) phreatic steam blasts - explosion pits, ejecta blankets of ash and blocks. Preliminary results indicate multiple fissure eruptions and growth of a basin-filled lava lake up to ~ 10 m thick with outflow sheet lava flows. Remnant mounds of original lake crust reveal an early high lava lake level, which subsided as much as 5 m as the molten interior drained back into the fissure system. Rapid loss of magma supply led to the collapse of fissure walls allowing groundwater influx that triggered multiple steam blasts along at least 500 m. Early blasts occurred while lake magma pressure was still high enough to produce squeeze-ups when penetrated by ejecta blocks. The King's Bowl pit crater exemplifies processes of a small, but highly energetic

Novel QTLs affecting rice kernel fissure resistance discovered in the cultivar ‘Saber’ augment those from ‘Cybonnet’

Science.gov (United States)

Kernel fissures in rice (Oryza sativa L.) caused by pre- or post-harvest stresses are the leading cause of breakage among milled rice. Such breakage causes economic losses for producers, millers, and marketers. Five QTLs for kernel fissure resistance (FR) were identified among a set of 275 RILs de...

Comparison of botox and lateral internal sphincterotomy treatment outcomes in chronic anal fissures

Directory of Open Access Journals (Sweden)

Tolga Dinç

2014-03-01

Full Text Available Objective: Both botox and lateral internal sfinkterotomi are treatment technics used in chronic anal fissure; provide the relaxation of anal sphincter and as a result of this, healing occurs. Aim of this study is to compare efficacy of botox and LIS treatment in chronic anal fissure and discussing with the literature. Methods: 60 of 66 patients who has chronic anal fissure, that we reached, treated but not healed with medical therapy, appealed to the Dr. Sami Ulus Hospital included the study. Gender, age, fissure localization, complaints (pain, bleeding, itching, constipation, complaint length, recurrences after treatment, continence conditions and complications of patients were registered. Results: Sixty patients were enrolled the study. Of the 60 patients; 38(63.3% were male and 22 (27.7% were female. Mean age of all patients was 35.93 ± 11.45 (21 -60. Pain was the common complaint of the all patients. 10 (32.3% recurrence were detected in botox treatment group (Group-I, only 1 (3.4% recurrence was in LIS group (Group-II. There was no complication as an incontinence in group-I but 3 cases with incontinence (10.39% were obtained in group-II. In the evaluation of these 3 cases by Cleveland Clinic Continence Scoring System, 2 cases classified as gas incontinence and 1 case as moderate fecal incontinence. Conclusion: Although botulinum toxin injection seen as an alternative treatment method with low complication rates such as incontinence, high recurrence is an important shortcoming of this technic. LIS performed by experienced surgeons remained the most popular treatment modality with low complication rates and great deal of healing success.

Landslide Fissure Inference Assessment by ANFIS and Logistic Regression Using UAS-Based Photogrammetry

Directory of Open Access Journals (Sweden)

Ozgun Akcay

2015-10-01

Full Text Available Unmanned Aerial Systems (UAS are now capable of gathering high-resolution data, therefore, landslides can be explored in detail at larger scales. In this research, 132 aerial photographs were captured, and 85,456 features were detected and matched automatically using UAS photogrammetry. The root mean square (RMS values of the image coordinates of the Ground Control Points (GPCs varied from 0.521 to 2.293 pixels, whereas maximum RMS values of automatically matched features was calculated as 2.921 pixels. Using the 3D point cloud, which was acquired by aerial photogrammetry, the raster datasets of the aspect, slope, and maximally stable extremal regions (MSER detecting visual uniformity, were defined as three variables, in order to reason fissure structures on the landslide surface. In this research, an Adaptive Neuro Fuzzy Inference System (ANFIS and a Logistic Regression (LR were implemented using training datasets to infer fissure data appropriately. The accuracy of the predictive models was evaluated by drawing receiver operating characteristic (ROC curves and by calculating the area under the ROC curve (AUC. The experiments exposed that high-resolution imagery is an indispensable data source to model and validate landslide fissures appropriately.

Turbofan Engine Core Compartment Vent Aerodynamic Configuration Development Methodology

Science.gov (United States)

Hebert, Leonard J.

2006-01-01

This paper presents an overview of the design methodology used in the development of the aerodynamic configuration of the nacelle core compartment vent for a typical Boeing commercial airplane together with design challenges for future design efforts. Core compartment vents exhaust engine subsystem flows from the space contained between the engine case and the nacelle of an airplane propulsion system. These subsystem flows typically consist of precooler, oil cooler, turbine case cooling, compartment cooling and nacelle leakage air. The design of core compartment vents is challenging due to stringent design requirements, mass flow sensitivity of the system to small changes in vent exit pressure ratio, and the need to maximize overall exhaust system performance at cruise conditions.

Permeability of fissured rock - an experimental study with special regard to the water injection test

International Nuclear Information System (INIS)

Schneider, H.J.

1987-01-01

The permeability to water of fissured rock is one of the most important design parameters for many underground projects, such as, e.g. the final deposition of radioactive waste. Because the conventional water injection test according to LUGEON for the calculation of permeability to water is associated with a high degree of uncertainty, new test equipment was developed. This equipment works on the principle of the water injection tracer test and multi-level measurements, enabling detailed measurement of the flow process at injection site and in the rock. The tests were carried out in Bunter sandstone and granite. The LUGEON test concept was varied in short-term and long-term tests at identical geological boundary conditions, and with test control at constant pressure on the one hand and at constant injection volume on the other. The test results show that non-steady-state flow occurs with short injection times, whereby the range is limited to the local rock at injection site. An increasing in injection time can lead to an increase in range by a number of factors as well as to steady-state flow conditions. The permeability of the rock types investigated is inhomgeneous and anistropic as a result of the fissured structure. (orig./HP) With 114 figs., 4 tabs [de

The movement of solutes through aqueous fissures in micro-porous rock during borehole experiments

International Nuclear Information System (INIS)

Glueckauf, E.

1981-02-01

When a tracer is injected for a short period into a solution flowing through a fissure in micro-porous rock, that tracer is not only carried along by the aqueous stream, but its local concentration is also markedly affected by hydro-dynamic dispersion and by sideway diffusion and adsorption in the micro-porous rock. The process has been simulated by computer calculations and these have made it possible to obtain from the concentration-time curves observed in borehole experiments an assessment of the physical parameters involving the water velocity and the hydro-dynamic dispersion in the fissure, and the diffusion and adsorption in the micro-porous rock. With these parameters it was then possible to recalculate quantitatively the local concentration-time history. However, in actual borehole experiments, the velocity of the water stream in the fissure is not known, and numerous side effects can distort the shape of the observed tracer curves. In order to test the theoretical interpretation more thoroughly, it is therefore proposed to carry out a laboratory experiment which simulates the borehole test under strictly defined conditions. (author)

Calculational examination of the Baneberry event

International Nuclear Information System (INIS)

Terhune, R.W.; Glenn, H.D.; Burton, D.E.; McKague, H.L.; Rambo, J.T.

1977-01-01

On December 18, 1970, Baneberry, a 10-kt nuclear device, was detonated at a depth of 278 m in hole U8d at the Nevada Test Site. A shock-induced fissure near ground zero opened and vented radioactive gases and debris into the atmosphere. This report presents the calculational results describing the sequence of dynamic phenomena that produced the vent. The calculations predict the long positive velocity pulse and the surface motion that were observed experimentally. The surface fissure through which the material vented is the same radial distance from ground zero as the maximum horizontal displacement is calculated to be. The calculations predict a final cavity radius that is very close to the measured Baneberry cavity radius. Finally, the calculations indicate that an open fracture path runs from the cavity to the Baneberry Fault, up the fault to the spall region, and then vertically to the surface. This was the vent path predicted by calculations and is consistent with the vent path found from the radioactivity in postshot drill holes. Because of our extensions in computational capabilities, we believe this report advances the state of the art for numerical simulation of the containment problems associated with underground nuclear tests

Fissuring-chemical damaging on transfers in concrete

International Nuclear Information System (INIS)

Tognazzi, C.

1998-01-01

Concrete is a material often use in the nuclear wastes disposal. The safety analysis of a long time wastes disposal with concrete requires to verify the concrete behaviour in water. As concretes generally have cracks, it is necessary to study the crack propagation influence on chemical degradation. In this paper, the author presents diffusion tests on fissured and/or chemical aged cement. The chemical degradation of the material leads to a supplementary porosity by the hydrates decalcification and increases its diffusivity. The cracking impact is less important and can be experimentally concealed. (A.L.B.)

Modeling and numerical study of transfers in fissured environments; Modelisation et etude numerique des transferts en milieux fissures

Energy Technology Data Exchange (ETDEWEB)

Granet, S.

2000-01-28

Oil recovery from fractured reservoirs plays a very important role in the petroleum industry. Some of the world most productive oil fields are located in naturally fractured reservoirs. Modelling flow in such a fracture network is a very complex problem. This is conventionally done using a specific idealized model. This model is based on the Warren and Root representation and on a dual porosity, dual permeability approach. A simplified formulation of matrix-fracture fluid transfers uses a pseudo-steady-state transfer equation involving a constant exchange coefficient. Such a choice is one of the main difficulties of this approach. To get a better understanding of the simplifications involved in the dual porosity approach a reference model must be available. To obtain such a fine description, we have developed a new methodology. This technique called 'the fissure element methodology' is based on a specific gridding of the fractured medium. The fissure network is gridded with linear elements coupled with an unstructured triangular grid of matrix. An appropriate finite volume scheme has been developed to provide a good description of the flow. The numerical development of is precisely described. A simulator has been developed using this method. Several simulations have been realised. Comparisons have been done with different dual-porosity dual-permeability models. A reflexion concerning the choice of the exchange coefficient used in the dual porosity model is then proposed. This new tool has permit to have a better understanding of the production mechanisms of a complex fractured reservoir. (author)

Heavy metals from Kueishantao shallow-sea hydrothermal vents, offshore northeast Taiwan

Science.gov (United States)

Chen, Xue-Gang; Lyu, Shuang-Shuang; Garbe-Schönberg, Dieter; Lebrato, Mario; Li, Xiaohu; Zhang, Hai-Yan; Zhang, Ping-Ping; Chen, Chen-Tung Arthur; Ye, Ying

2018-04-01

Shallow water hydrothermal vents are a source of heavy metals leading to their accumulation in marine organisms that manage to live under extreme environmental conditions. This is the case at Kueishantao (KST) shallow-sea vents system offshore northeast Taiwan, where the heavy metal distribution in vent fluids and ambient seawater is poorly understood. This shallow vent is an excellent natural laboratory to understand how heavy and volatile metals behave in the nearby water column and ecosystem. Here, we investigated the submarine venting of heavy metals from KST field and its impact on ambient surface seawater. The total heavy metal concentrations in the vent fluids and vertical plumes were 1-3 orders of magnitude higher than the overlying seawater values. When compared with deep-sea hydrothermal systems, the estimated KST end-member fluids exhibited much lower concentrations of transition metals (e.g., Fe and Mn) but comparable concentrations of toxic metals such as Pb and As. This may be attributed to the lower temperature of the KST reaction zone and transporting fluids. Most of the heavy metals (Fe, Mn, As, Y, and Ba) in the plumes and seawater mainly originated from hydrothermal venting, while Cd and Pb were largely contributed by external sources such as contaminated waters (anthropogenic origin). The spatial distribution of heavy metals in the surface seawater indicated that seafloor venting impacts ambient seawater. The measurable influence of KST hydrothermal activity, however, was quite localized and limited to an area of heavy metals emanating from the yellow KST hydrothermal vent were: 430-2600 kg Fe, 24-145 kg Mn, 5-32 kg Ba, 10-60 kg As, 0.3-1.9 kg Cd, and 2-10 kg Pb. This study provides important data on heavy metals from a shallow-sea hydrothermal field, and it helps to better understand the environmental impact of submarine shallow hydrothermal venting.

Safe venting of ''red oil'' runaway reactions

International Nuclear Information System (INIS)

Paddleford, D.F.; Fauske, H.K.

1994-01-01

Calorimetry testing of Tri-n-butyl phosphate (TBP) saturated with strong nitric acid was performed to determine the relationship between vent size and pressure buildup in the event of a runaway reaction. These experiments show that runaway can occur in an open system, but that even when runaway is induced in the TBP/HN0 3 system, dangerous pressure buildup will be prevented with practical vent size

Experimental investigation of passive thermodynamic vent system (TVS) with liquid nitrogen

Science.gov (United States)

Bae, Junhyuk; Yoo, Junghyun; Jin, Lingxue; Jeong, Sangkwon

2018-01-01

Thermodynamic vent system (TVS) is an attractive technology to maintain an allowable pressure level of a cryogenic propellant storage in a spacecraft under micro-gravity condition. There are two types of TVS; active or passive. In this paper, the passive TVS which does not utilize a cryogenic liquid circulation pump is experimentally investigated with liquid nitrogen and numerically analyzed by thermodynamic and heat transfer model. A cylindrical copper tank, which is 198 mm in inner diameter and 216 mm in height, is utilized to suppress a thermal-stratification effect of inside cryogenic fluid. A coil heat exchanger, which is 3 m in length and 6.35 mm in outer diameter, and a fixed size orifice of which diameter is 0.4 mm are fabricated to remove heat from the stored fluid to the vented flow. Each vent process is initiated at 140 kPa and ended at 120 kPa with liquid nitrogen fill levels which are 30%, 50% and 70%, respectively. In the numerical model, the fluid in the tank is assumed to be homogeneous saturated liquid-vapor. Mass and energy balance equations with heat transfer conditions suggested in this research are considered to calculate the transient pressure variation in the tank and the amount of heat transfer across the heat exchanger. We achieve the average heat rejection rate of more than 9 W by TVS and conclude that the passive TVS operates satisfactorily. In addition, the prediction model is verified by experimental results. Although the model has limitation in providing accurate results, it can surely predict the tendency of pressure and temperature changes in the tank. Furthermore, the model can suggest how we can improve the heat exchanger design to enhance an overall efficiency of passive TVS. Moreover, the performance of passive TVS is compared with other cryogenic vent systems (direct vent system and active TVS) by suggested performance indicator.

The use of Remote Sensing for the Study of the Relationships Between Tectonics and Volcanism

Science.gov (United States)

Chorowicz, J.; Dhont, D.; Yanev, Y.; Bardintzeff, J.

2004-12-01

Observations of geometric relationships between tectonics and volcanism is a fruitful approach in geology. On the one hand analysis of the distribution and types of volcanic vents provides information on the geodynamics. On the other hand tectonic analysis explains the location of volcanics vents. Volcanic edifices often result from regional scale deformation, forming open structures constituting preferred pathways for the rise of magmas. Analysis of the shape and the distribution of vents can consequently provide data on the regional deformation. Remote sensing imagery gives synoptic views of the earth surface allowing the analysis of landforms of still active tectonic and volcanic features. Shape and distribution of volcanic vents, together with recent tectonic patterns are best observed by satellite data and Digital Elevation Models than in the field. The use of radar scenes for the study of the structural relationships between tectonic and volcanic features is particularly efficient because these data express sensitive changes in the morphology. In various selected areas, we show that volcanic edifices are located on tension fractures responsible for fissure eruptions, volcanic linear clusters and elongate volcanoes. Different types of volcanic emplacements can be also distinguished such as tail-crack or horse-tail features, and releasing bend basins along strike-slip faults. Caldera complexes seem to be associated to horse-tail type fault terminations. At a regional scale, the distribution of volcanic vents and their relationships with the faults is able to explain the occurrence of volcanism in collisional areas.

Effects of menthol essence and breast milk on the improvement of nipple fissures in breastfeeding women

Directory of Open Access Journals (Sweden)

Sedigheh Amir Ali Akbari

2014-01-01

Full Text Available Background: Nipple fissure is a common disorder during breastfeeding. With high prevalence of nipple fissures and its impacts on breastfeeding, as well as the existence of evidence in favor of the application of peppermint as an antiinflammatory and antiinfection herb, the purpose of this study is to determine the effect of Menthol essence on improving nipple fissures in the primiparous breastfeeding women. Materials and Methods: This study was conducted using a clinical trial method. Samples were divided randomly into two groups of 55 women. The women in the peppermint group applied four drops of Menthol essence on their nipple and areola after each feeding. The control group applied four drops of their own milk on the nipple and areola after each feeding. Then, the two groups were studied on days 10 and 14 postpartum. For intensity of pain, the visual analog scale (0-10 cm and to measure the severity of damage, Amir scale (1-10 cm were applied and the existence or lack of nipple discharge was also recorded. The data were analyzed using SPSS 17 software. Results: The mean intensity of pain and nipple fissure before treatment (8.55 ± 1.74 and day 10 after delivery (4.26 ± 1.57 and before treatment and day 14 after delivery in the case group (1.32 ± 1.02 had a significant difference (P < 0.001. Nipple discharge between the two groups, before treatment (%75.2 and day 10 after delivery (%31.6 and before treatment and day 14 after delivery (%15.7, the case group had a significant difference (P < 0.001. Conclusion: Menthol essence can improve nipple fissures in the primiparous breastfeeding women.

Management of turbidity current venting in reservoirs under different bed slopes.

Science.gov (United States)

Chamoun, Sabine; De Cesare, Giovanni; Schleiss, Anton J

2017-12-15

The lifetime and efficiency of dams is endangered by the process of sedimentation. To ensure the sustainable use of reservoirs, many sediment management techniques exist, among which venting of turbidity currents. Nevertheless, a number of practical questions remain unanswered due to a lack of systematic investigations. The present research introduces venting and evaluates its performance using an experimental model. In the latter, turbidity currents travel on a smooth bed towards the dam and venting is applied through a rectangular bottom outlet. The combined effect of outflow discharge and bed slopes on the sediment release efficiency of venting is studied based on different criteria. Several outflow discharges are tested using three different bed slopes (i.e., 0%, 2.4% and 5.0%). Steeper slopes yield higher venting efficiency. Additionally, the optimal outflow discharge leading to the largest venting efficiency with the lowest water loss increases when moving from the horizontal bed to the inclined positions. Copyright © 2017 Elsevier Ltd. All rights reserved.

Sealing effectiveness of fissure sealant bonded with universal adhesive systems on saliva-contaminated and noncontaminated enamel.

Science.gov (United States)

Memarpour, Mahtab; Shafiei, Fereshteh; Zarean, Mehran; Razmjoei, Faranak

2018-01-01

The effectiveness of sealants is dependent upon their adhesion to enamel surface. The aim of the study was to evaluate the sealing ability of a pit and fissure sealant used with a universal adhesive (etch-and-rinse vs. self-etch modes) when the site is contaminated with saliva. Adhesive properties were evaluated as microleakage and scanning electron microscopic (SEM) characteristics. A total of 72 mandibular third molars were randomly divided into 6 groups (n=12). Occlusal pits and fissures were sealed with an unfilled resin fissure sealant (FS) material with or without saliva contamination. The groups included: 1) phosphoric acid etching + FS (control), 2) phosphoric acid etching + Scotchbond Universal (etch-and-rinse) + FS, 3) phosphoric acid etching + saliva + Scotchbond Universal (etch-and-rinse) + FS, 4) Scotchbond Universal (self-etching) + FS,5) Scotchbond Universal (self-etching) + saliva + FS, and 6) Scotchbond Universal (self-etching) + saliva + Scotchbond Universal + FS. After thermocycling, the teeth were placed in 0.5% fuchsin, sectioned, and evaluated by digital microscopy. Two samples from each group were also observed by SEM. The data were analyzed with Kruskal-Wallis and Mann-Whitney tests for a significance of p universal adhesive in etch-and-rinse or self-etch modes was similar to that of conventional acid etching. Saliva contamination had a negative effect on sealant adhesion to pretreated enamel. Key words: Pit and fissure sealant, Universal adhesive, Saliva.

Are vent crab behavioral preferences adaptations for habitat choice?

Science.gov (United States)

Dahms, Hans-Uwe; Tseng, Li-Chun; Hwang, Jiang-Shiou

2017-01-01

Hydrothermal vent organisms are adapted to their extreme and patchily distributed habitats. They are expected to have evolved mechanisms that keep them in their specific habitation. Since little is known about the recruitment or habitat selection of HV organisms such as brachyurans, we examined the properties of several hydrothermal vent-associated cues on the behavior of the hydrothermal vent (HV) crab Xenograpsus testudinatus in the laboratory that were contrasted by the offering of non-vent cues. This crab species is endemic and dominates the vent fauna of Turtle Island off the NE coast of Taiwan. HV crabs were separately and in combination offered the following vent-specific cues: (1) sulfuric sediment, (3) air-bubbling, (4) elevated temperature, (5) dead settled zooplankton, (7) other crabs, and (8) shade. The non-vent-specific cues were: (2) quarz sediment, (6) dead fish, (8) light. These cues were provided on either side of a two-choice chamber. The movement of individual crabs was monitored: as initial and final choices, and as the proportion of time the crabs spent in each compartment (resident time). Cues were offered alone and no such cue as a control in the same set-up. Sulfuric sediments and dead fish were significantly more attractive to females, and other crabs irrespective of gender were significantly more attractive to males. When compared to expected distributions, crabs, irrespective of gender, significantly avoided light and tended to select other crabs, air-bubbling, sulfuric sediment, elevated temperature, dead fish, dead zooplankton, and quarz sediments in the order of decreasing importance. Data do not support the hypothesis that dead settled zooplankton was particularly attractive nor that the other gender was selected. A combination of several vent-associated cues (sulfuric sediment, elevated temperature, air-bubbling) facilitated the strongest attraction to the crabs as reflected by all response variables. The 'first choice' responses

The differences of saliva pH before and after application of Bis-GMA resin based-pit and fissure sealant

Directory of Open Access Journals (Sweden)

Ayub Irmadani Anwar

2016-06-01

Full Text Available Pit and fissure sealant applications is one way to prevent caries. One of the effective ingredient as a pit and fissure sealant is a Bis-GMA resin. One of the active components  of  Bis-GMA  resin  is  sodium  fluoride,  which is capable  of releasing fluoride ions to the tooth surface and able to improve the repair and remineralization process through the replacement  of  calcium and phosphate ions found in saliva to increase the pH of saliva. This study was to determine the effect of pit and fissure sealant applications made from Bis-GMA resin to pH of saliva in children aged 6-12 years. The study design is pre and post test with control group design. Saliva samples were derived from 15 pediatric patients has met the criteria. The pH of saliva were taken before and after the application of pit and fissure sealant made from Bis-GMA and measured with pH meter. This study used a non-parametric test, the Wilcoxon Signed Rank test. The results of this study are also supported by the results of statistical tests showed p-: 0.005 (p<0.05 value, which means that there are significant differences in pH of saliva before and after the application of pit and fissure sealant made from Bis-GMA resin.

Hydrodynamic calculation of a filter sand bed type used in the containment venting systems; Calculo hidrodinamico de un filtro tipo lecho de arena usado en los sistemas de venteo de la contencion

Energy Technology Data Exchange (ETDEWEB)

Cuevas V, D.; Sainz M, E.; Ortiz V, J., E-mail: delfy.cu@gmail.com [ININ, Carretera Mexico-Toluca s/n, 52750 Ocoyoacac, Estado de Mexico (Mexico)

2015-09-15

The filtered venting of the containment has been adopted in European countries to mitigate the consequences of excess pressure containment during a severe accident. When venting has taken place, the fission products are released directly into the environment, unless a filter on the same path is placed, so that various types of filters are used to trap the fission products. The venting filters of the containment currently installed use different filtration technologies that involve more than one medium. Those using water as the first stage of filtration are called wet systems and are equipped with additional steps to remove water drops and fine aerosols emissions. And even they may also be equipped with an element containing certain absorption means for the filtration of gaseous iodine species. Other designs based on filtration of deep bed as the primary retention step; called dry filters, use filtration media of metal fiber, ceramic or sand to trap aerosols. This paper evaluates the hydraulic characteristics of the filter sand bed type designed by EDF as a candidate to be installed in the containment of BWR Mark II (type of primary containment of the nuclear power plant of Laguna Verde). The evaluation of filter sand bed type was performed using the software package of open source OpenFOAM. Models of each zone of the filtered device were generated and through a series of parametric calculations of computational fluid mechanics relevant hydrodynamic characteristics of the device were obtained, such as pressure drops against mass flow rate and pressure fields and speed at different operating conditions. On the other hand, the model validation of the sand bed filter when comparing the results of experimental tests on a sand column of PITEAS program (1985-1986) against OpenFOAM simulation was realized. The results are very close to those obtained experimentally. (Author)

Migration of radionuclides in fissured rock - The influence of micropore diffusion and longitudinal dispersion

International Nuclear Information System (INIS)

Rasmuson, A.; Neretnieks, I.

1979-12-01

The migration of radionuclides in the fissures in the bedrock surrounding a repository is discussed. A one-dimensional transport model is presented. It includes diffusion of the nuclides into the microfissures of the rock, and linear sorption and longitudinal dispersion in the bedrock. An analytical solution to the model is given in terms of an infinite integral. The integrand is a sometimes highly oscillatory function of the system parameters. A special integration method is developed to evaluate the infinite integral. The method utilizes the oscillatory behavior of the integrand. The assessment of input parameters is discussed in some detail. Dimensionless breakthrough curves are given for the approximate range of variation of the input parameters. Calculations are made for a repository of spent fuel surrounded by fissured but fairly good rock (K(sub)p=10- 9 m/s and fissure spacing S=50 m). Longitudinal dispersion may significantly affect the amount of radioactive material reaching the biosphere. Radionuclides, which would decay completely without longitudinal dispersion, may arrive in non-negligible concentrations. Dispersion effects of the magnitude considered in this study can significantly diminish the retardation effects of matrix diffusion. (authors)

Migration of radionuclides in fissured rock: The influence of micropore diffusion and longitudinal dispersion

International Nuclear Information System (INIS)

Rasmuson, A.; Neretnieks, I.

1981-01-01

The migration of radionuclides in the fissures in the bedrock surrounding a repository is discussed. A one-dimensional transport model is presented. It includes diffusion of the nuclides into the microfissures of the rock, and linear sorption, and longitudinal dispersion in the bedrock. An analytical solution to the model is given in terms of an infinite integral. The integrand is a sometimes highly oscillatory function of the system parameters. A special integration method is developed to evaluate the infinite integral. The method utilizes the oscillatory behavior of the integrand. The assessment of input parameters is discussed in some detail. Dimensionless breakthrough curves are given for the approximate range of variation of the input parameters. Calculations are made for a repository of spent fuel surrounded by fissured but fairly good rock (K/sub p/ = 10 -9 m/s and fissure spacing S = 50 m). Longitudinal dispersion may significantly affect the amount of radioactive material reaching the biosphere. Radionuclides, which would decay completely without longitudinal dispersion, may arrive in nonnegligible concentrations. Dispersion effects of the magnitude considered in this study can significantly diminish the retardation effects of matrix diffusion

Explosive volcanism on Mercury: Analysis of vent and deposit morphology and modes of eruption

Science.gov (United States)

Jozwiak, Lauren M.; Head, James W.; Wilson, Lionel

2018-03-01

The MESSENGER mission revealed, for the first time, conclusive evidence of explosive volcanism on Mercury. Several previous works have cataloged the appearance and location of explosive volcanism on the planet using a variety of identifying characteristics, including vent presence and deposit color as seen in multispectral image mosaics. We present here a comprehensive catalog of vents of likely volcanic origin; our classification scheme emphasizes vent morphology. We have analyzed the morphologies of all vents in our catalog, and recognize three main morphologies: "simple vent", "pit vent", and "vent-with-mound". The majority of vents we identify are located within impact craters. The spatial distribution of vents does not correlate with the locations of volcanic smooth plains deposits, in contrast to the Moon, nor do vents correlate with the locations of large impact basins (except for the Caloris and Tolstoj basins). Using the degradation state of the vent host crater as a proxy for maximum age, we suggest that vent formation has been active through the Mansurian and into the Kuiperian periods, although the majority of vents were likely formed much earlier in mercurian history. The morphologies and locations of vents are used to investigate a set of plausible formation geometries. We find that the most likely and most prevalent formation geometry is that of a dike, stalled at depth, which then explosively vents to the surface. We compare the vent and deposit size of mercurian pyroclastic deposits with localized and regional lunar pyroclastic deposits, and find a range of possible eruption energies and corresponding variations in eruption style. Localized lunar pyroclastic deposits and the majority of mercurian pyroclastic deposits show evidence for eruption that is consistent with the magmatic foam at the top of a dike reaching a critical gas volume fraction. A subset of mercurian vents, including the prominent Copland-Rachmaninoff vent to the northeast of the

Tank vent processing system having a corrosion preventive device

International Nuclear Information System (INIS)

Ouchi, Shoichi; Sato, Hirofumi

1987-01-01

Purpose: To prevent corrosion of a tank vent processing device by injecting an oxygen gas. Constitution: Oxygen gas and phosphorous at high temperature are poured into a tank vent processing device and amorphous oxide layers optimum to the prevention of external corrosion are formed to the inner surface of the device. Since the corrosion preventive device using the oxygen gas injection can be constituted as a relatively simple device, it is more economical than constituting a relatively large tank vent processing device with corrosion resistant stainless steels. (Kamimura, M.)

Causes of the fissure formation with shrinkage of metal on low carbon steel slabs

International Nuclear Information System (INIS)

Ksenzuk, F.A.; Khudas, A.L.; Zelenskaya, D.P.

1977-01-01

The causes have been investigated underlying the formation of fissures with spread of metal on low-carbon steel slabs during hot rolling. Metallographic investigations of templates from various sections of work pieces from 15-ton ingots of 08 ps (kp) steels have indicated that the fissures on the slabs are formed after the metal spreads along the small plane and the work piece thins out in the course of rolling because of the opening of large thin-walled honeycomb bubbles. The phenomenon was confirmed schematically on a model in the form of a slab-shaped lead specimen with longitudinal hole of a variable diameter close to one of the edges

Fissured and geographic tongue in Williams-Beuren syndrome

Directory of Open Access Journals (Sweden)

Neeta Sharma

2014-01-01

Full Text Available Williams-Beuren Syndrome (WBS is a rare, most often sporadic, genetic disease caused by a chromosomal microdeletion at locus 7q11.23 involving 28 genes. It is characterized by congenital heart defects, neonatal hypercalcemia, skeletal and renal abnormalities, cognitive disorder, social personality disorder, and dysmorphic facies. A number of clinical findings has been reported, but none of the studies evaluated this syndrome considering oral cavity. We here report a fissured and geographic tongue in association with WBS.

Effects of venting on wind noise levels measured at the eardrum.

Science.gov (United States)

Chung, King

2013-01-01

Wind noise can be a nuisance to hearing aid users. With the advent of sophisticated feedback reduction algorithms, people with higher degrees of hearing loss are fit with larger vents than previously allowed, and more people with lesser degrees of hearing loss are fit with open hearing aids. The purpose of this study was to examine the effects of venting on wind noise levels in the ear canal for hearing aids with omnidirectional and directional microphones. Two behind-the-ear hearing aids were programmed when they were worn on a Knowles Electronics Manikin for Acoustic Research. The hearing aid worn on the right ear was programmed to the omnidirectional microphone mode and the one on the left to the directional microphone mode. The hearing aids were adjusted to linear amplification with flat frequency response in an anechoic chamber. Gains below 10 dB were used to avoid output limiting of wind noise levels at low input levels. Wind noise samples were recorded at the eardrum location in a wind tunnel at wind velocities ranging from a gentle to a strong breeze. The hearing aids were coupled to #13 tubings (i.e., open vent), or conventional skeleton earmolds with no vent, pressure vents, or 3mm vents. Polar and spectral characteristics of wind noise were analyzed off-line using MatLab programs. Wind noise levels in the ear canals were mostly predicted by vent-induced frequency response changes in the conventional earmold conditions for both omnidirectional and directional hearing aids. The open vent condition, however, yielded the lowest levels, which could not be entirely predicted by the frequency response changes of the hearing aids. This indicated that a wind-related vent effect permitted an additional amount of sound reduction in the ear canal, which could not be explained by known vent effects. For the microphone location, form factor, and gain settings tested, open fit hearing aids yielded lower noise levels at the eardrum location than conventional behind

Fine mapping and introgressing qFIS1-2, a major QTL for kernel fissure resistance in rice (Oryza sativa L.)

Science.gov (United States)

Rice (Oryza sativa L.) kernel fissuring increases breakage during milling and decreases the value of processed rice. This study employed molecular gene tagging methods to fine-map a fissure resistance (FR) locus in ‘Cybonnet’, a semidwarf tropical japonica cultivar, as well as transfer this trait to...

Natural Ventilation Effectiveness of Round Wall-Mounted Vent Caps in Residential Kitchens

Directory of Open Access Journals (Sweden)

Yi-Pin Lin

2018-05-01

Full Text Available This study explores the effect of different numbers of wall-mounted vent caps and their installation locations on the indoor air environment in residential kitchens, for which limited information is available. Wind tunnel tests were performed to study the induced ventilation rates of a vent cap, and the impact of vent caps on the natural ventilation efficiency in residential kitchens was examined using computational fluid dynamics (CFD numerical simulations. The results were then applied to determine the appropriate quantity of vent caps and their proper installation location. The wind tunnel test results indicated that outdoor winds with speeds of 0–6 m/s that flow parallel to the wall with a vent cap induce indoor air to exit through the cap with ventilation rates of 0–20 m3/h; when the wind blows perpendicular to the wall, outdoor air with 0–31.9 m3/h flows indoors. CFD numerical simulations showed that the installation of kitchen vent caps can reduce the average carbon monoxide concentration in the cook’s breathing zone. A sufficient quantity of vent caps and the proper installation location are required to ensure the natural ventilation effectiveness of wall-mounted vent caps.

Effect of Intermittent Drying Conditions on Fissuring Percentage and Process Duration of Long and Medium Rough Rice Varieties

Directory of Open Access Journals (Sweden)

A. Ghasemi

2016-02-01

Full Text Available One of the factors which affect the quality of rice during milling is internal fissures created during and after drying operation. In many industrial countries intermittent drying method is hired to reduce the moisture content of rough rice in order to reduce the drying time and maintain the quality of the final product. A high percentage of rice breakage during milling process, at least in Iran, necessitates performing the intermittent drying process and optimize it for Iranian varieties. In this study, the effect of this method (drying-tempering and continuous drying method (no tempering on fissuring percentage of Hashemi (long grain and Koohsar (medium grain varieties was investigated. The experiments were carried out at constant drying and tempering temperature of 60 °C, drying durations of 20, 40 and 60 min, and tempering durations of 0 (continuous drying, 40, 80, 120, 160, 200, 240 min. The results revealed that the tempering process significantly reduced the drying time and fissured kernels percentage. Moreover, for both varieties it was observed that the rice fissuring decreased significantly by continuing the tempering process until certain durations. Overall, for optimization of intermittent drying process in terms of the considered qualitative parameters, i.e. reducing energy consumption and losses, conducting 160 and 200 min tempering process after 40 min drying was found appropriate for Hashemi and Koohsar varieties, respectively. In addition, according to the higher fissuring for Koohsar (medium grain compared to Hashemi (long grain, it can be concluded that physical properties such as kernel slenderness ratio is effective on its fissuring.

Experimentally Testing Hydrothermal Vent Origin of Life on Enceladus and Other Icy/Ocean Worlds.

Science.gov (United States)

Barge, Laura M; White, Lauren M

2017-09-01

We review various laboratory strategies and methods that can be utilized to simulate prebiotic processes and origin of life in hydrothermal vent systems on icy/ocean worlds. Crucial steps that could be simulated in the laboratory include simulations of water-rock chemistry (e.g., serpentinization) to produce hydrothermal fluids, the types of mineral catalysts and energy gradients produced in vent interfaces where hydrothermal fluids interface with the surrounding seawater, and simulations of biologically relevant chemistry in flow-through gradient systems (i.e., far-from-equilibrium experiments). We describe some examples of experimental designs in detail, which are adaptable and could be used to test particular hypotheses about ocean world energetics or mineral/organic chemistry. Enceladus among the ocean worlds provides an ideal test case, since the pressure at the ocean floor is more easily simulated in the lab. Results for Enceladus could be extrapolated with further experiments and modeling to understand other ocean worlds. Key Words: Enceladus-Ocean worlds-Icy worlds-Hydrothermal vent-Iron sulfide-Gradient. Astrobiology 17, 820-833.

Gas explosion in domestic buildings. The vented gas explosion[sub][/sub

Directory of Open Access Journals (Sweden)

Tadeusz Chyży

2014-08-01

Full Text Available In this paper, the basic information, related to the so-called vented gas explosion, has been presented. The vented explosion it is an explosion, during which the destruction of the weakest elements of the structure occurs. Through the resulting holes (decompressing surfaces can flow both combustion products and non-burned gas mixture. In consequence, reduction of the maximum explosion pressure[i] P[sub]red [/sub][/i] may be significant. Often, a gas explosion occurs inside residential buildings. In this case, natural vents are window and door openings.[b]Keywords[/b]: gas, explosion, combustion, explosion vents

On the global distribution of hydrothermal vent fields: One decade later

Science.gov (United States)

Beaulieu, S. E.; Baker, E. T.; German, C. R.

2012-12-01

Since the last global compilation one decade ago, the known number of active submarine hydrothermal vent fields has almost doubled. At the end of 2009, a total of 518 active vent fields was catalogued, with about half (245) visually confirmed and others (273) inferred active at the seafloor. About half (52%) of these vent fields are at mid-ocean ridges (MORs), 25% at volcanic arcs, 21% at back-arc spreading centers (BASCs), and 2% at intra-plate volcanoes and other settings. One third are in high seas, and the nations with the most known active vent fields within EEZs are Tonga, USA, Japan, and New Zealand. The increase in known vent fields reflects a number of factors, including increased national and commercial interests in seafloor hydrothermal deposits as mineral resources. Here, we have comprehensively documented the percentage of strike length at MORs and BASCs that has been systematically explored for hydrothermal activity. As of the end of 2009, almost 30% of the ~60,000 km of MORs had been surveyed at least with spaced vertical profiles to detect hydrothermal plumes. A majority of the vents discovered at MORs in the past decade occurred at segments with vs. weighted-average full spreading rate (u_s), we predicted 676 vent fields remaining to be discovered at MORs. Even accounting for the lower F_s at slower spreading rates, almost half of the vents that are predicted remaining to be discovered at MORs are at ultra-slow to slow spreading rates (explored tend to be at high latitudes, such as the ultra-slow to slow spreading Arctic MORs (e.g., Kolbeinsey and Mohns Ridges), the ultra-slow American-Antarctic Ridge, and the intermediate spreading Pacific-Antarctic Ridge. Although a greater percentage of the ~11,000 km of BASCs has been surveyed for hydrothermal activity, the discoveries at BASCs in the past decade were mainly at segments with intermediate to fast spreading rates. Using the same equation for F_s vs. u_s, we predicted 71 vent fields remaining to

Visualization of the air flow behind the automotive benchmark vent

OpenAIRE

Pech, Ondřej; Jedelský, Jan; Caletka, Petr; Jícha, Miroslav

2015-01-01

Passenger comfort in cars depends on appropriate function of the cabin HVAC system. A great attention is therefore paid to the effective function of automotive vents and proper formation of the flow behind the ventilation outlet. The article deals with the visualization of air flow from the automotive benchmark vent. The visualization was made for two different shapes of the inlet channel connected to the benchmark vent. The smoke visualization with the laser knife was used. The influence of ...

Enamel pretreatment with Er:YAG laser: effects on the microleakage of fissure sealant in fluorosed teeth

Directory of Open Access Journals (Sweden)

Mahtab Memarpour,

2014-08-01

Full Text Available Objectives The purpose of this in vitro study was to evaluate the microleakage and penetration of fissure sealant in permanent molar teeth with fluorosis after pretreatment of the occlusal surface. Materials and Methods A total of 120 third molars with mild dental fluorosis were randomly divided into 6 groups (n = 20. The tooth surfaces were sealed with an unfilled resin fissure sealant (FS material. The experimental groups included: 1 phosphoric acid etching (AE + FS (control; 2 AE + One-Step Plus (OS, Bisco + FS; 3 bur + AE + FS; 4 bur + AE + OS + FS; 5 Er:YAG laser + AE + FS; and 6 Er:YAG laser + AE + OS + FS. After thermocycling, the teeth were immersed in 0.5% fuchsin and sectioned. Proportions of mircoleakage (PM and unfilled area (PUA were measured by digital microscope. Results Overall, there were significant differences among all groups in the PM (p = 0.00. Group 3 showed the greatest PM, and was significantly different from groups 2 to 6 (p < 0.05. Group 6 showed the lowest PM. Pretreatment with Er:YAG with or without adhesive led to less PM than bur pretreatment. There were no significant differences among groups in PUA. Conclusions Conventional acid etching provided a similar degree of occlusal seal in teeth with fluorosis compared to those pretreated with a bur or Er:YAG laser. Pretreatment of pits and fissures with Er:YAG in teeth with fluorosis may be an alternative method before fissure sealant application.

Posterior perineal support as treatment for anal fissures--preliminary results with a new toilet seat device.

Science.gov (United States)

Tan, Kok-Yang; Seow-Choen, Francis; Hai, Chew Heng; Thye, Gan Kok

2009-03-01

Anal fissures can cause morbidity in an otherwise healthy young patient. The process of evacuation results in stretching and descent of the anoderm and perineum especially posteriorly. Posterior perineal support may provide counter pressure at the posterior aspect of the pelvic floor, balancing the pressure exerted by the faeces on the anal wall, thus improving evacuation and reducing the trauma associated with it, and reducing symptoms of anal fissures. Symptoms of constipation may also be reduced secondarily. We report the preliminary results with a novel, simple and noninvasive method of treatment provided by a toilet seat device. A prospective study was performed in 32 patients. The study was designed mainly to investigate the patients' subjective perceptions of their symptoms related to anal fissures and constipation. Questionnaires were provided to patients before, during and after treatment. The study revealed statistically significant improvement in pain, bleeding, symptoms of constipation and abdominal discomfort after 3 months usage of the device. The odds of patients perceiving an improvement in symptoms were also significantly increased after 3 months of treatment compared to 2 weeks of treatment. This preliminary study revealed that a posterior perineal support device can bring about significant improvement in the symptoms of patients with anal fissures. There may also be secondary benefits of a reduction in the symptoms of constipation. Although not conclusive, these results should serve as a springboard for further research into this area.

Genetic diversity of archaea in deep-sea hydrothermal vent environments.

Science.gov (United States)

Takai, K; Horikoshi, K

1999-08-01

Molecular phylogenetic analysis of naturally occurring archaeal communities in deep-sea hydrothermal vent environments was carried out by PCR-mediated small subunit rRNA gene (SSU rDNA) sequencing. As determined through partial sequencing of rDNA clones amplified with archaea-specific primers, the archaeal populations in deep-sea hydrothermal vent environments showed a great genetic diversity, and most members of these populations appeared to be uncultivated and unidentified organisms. In the phylogenetic analysis, a number of rDNA sequences obtained from deep-sea hydrothermal vents were placed in deep lineages of the crenarchaeotic phylum prior to the divergence of cultivated thermophilic members of the crenarchaeota or between thermophilic members of the euryarchaeota and members of the methanogen-halophile clade. Whole cell in situ hybridization analysis suggested that some microorganisms of novel phylotypes predicted by molecular phylogenetic analysis were likely present in deep-sea hydrothermal vent environments. These findings expand our view of the genetic diversity of archaea in deep-sea hydrothermal vent environments and of the phylogenetic organization of archaea.

Vent rate of superconducting magnets during quench in the Mirror Fusion Test Facility

International Nuclear Information System (INIS)

Slack, D.S.

1979-01-01

When a superconducting magnet goes normal, resistive heating in the conductor evaporates surrounding LHe, which must be vented. The nature and speed at which the magnet goes normal and He is vented are not subject to rigorous analysis. This paper presents vent data from an existing magnet. An approximate mathematical model is derived and fitted to the data to permit scaling of vent requirements to larger size magnets. The worst case models of the vent employed in Mirror Fusion Test Facility (MFTF) cryogenic system design are also presented

Ground fissures in the area of Mavropigi Village (N. Greece): Seismotectonics or mining activity?

Science.gov (United States)

Kalogirou, Eleni; Tsapanos, Theodoros; Karakostas, Vassilios; Marinos, Vassilios; Chatzipetros, Alexandros

2014-12-01

In the beginning of July 2010, a ground fissure was observed in the field near the village of Mavropigi (Northern Greece) and specifically in its NW side. Later on (early September), a second ground fissure was perceived, close and almost parallel to the first one and very close to the limits of the lignite exploitation mine (by the Public Power Corporation, PPC). It was observed that the village of Mavropigi slides away slowly towards the PPC lignite mine. Geological, seismological, as well as geotechnical survey in the field indicated that the phenomenon is related to the coal mining exploitation in the near vicinity of the village rather than to any seismotectonic activity in the surrounding area.

The filtered venting system under construction at barseback

International Nuclear Information System (INIS)

Persson, A.H.

1985-01-01

A filter venting containment system, bearing the acronym FILTRA will be installed at the Swedish nuclear power plant Barseback. The Barseback Power Plant is owned by the Southern Sweden Power Supply (Sydkraft AB) and has two 1700-MW boiling water reactors. The reactors are of ASEA-ATOM design with pressure suppression containments (Mark IItype). The installation of the filter venting system is a condition set by the Swedish government for a continued operating license after September 1, 1986. The construction work for the FILTRA plant, the first of its kind ever planned, will be completed at the end of 1985. The FILTRA is designed so that 99.9% of the core inventory of radioactivity, excluding inert gases, is retained in the reactor containment and filter system in the event of containment venting. Another design guideline is to achieve passive functioning of the FILTRA plant during the first 24 h of an accident. The FILTRA plant is common to the two reactors on the site and consists mainly of two systems, a venting system (pressure relief system) and a filtering system. The total cost is approximately U.S. $15 million

Duane retraction syndrome type 1 with Usher syndrome type 2: an unreported association.

Science.gov (United States)

Khurana, Bhawna Piplani; Khurana, Aruj Kumar; Grover, Sumit

2015-05-07

Duane retraction syndrome is characterized by globe retraction and palpebral fissure narrowing on adduction, with restriction of abduction, adduction, or both. Usher syndrome type 2 consists of congenital bilateral sensorineural hearing loss and retinitis pigmentosa. The authors present a case with a yet unreported association between Duane retraction syndrome type 1 and Usher syndrome type 2. Copyright 2015, SLACK Incorporated.

The ProVent model learns to speak French.

Science.gov (United States)

Cox, Christopher E

2014-10-20

Leroy and colleagues report on the accuracy of the Prolonged Mechanical Ventilation Prognostic Model ('ProVent') in a cohort study of patients ventilated for at least 21 days in one of three hospitals in the north of France. This study is noteworthy because it is the first to describe the performance of the ProVent model both outside the US and in a community hospital-based setting.

Land subsidence and earth fissures in south-central and southern Arizona, USA

Science.gov (United States)

Conway, Brian D.

2016-05-01

Land subsidence due to groundwater overdraft has been an ongoing problem in south-central and southern Arizona (USA) since the 1940s. The first earth fissure attributed to excessive groundwater withdrawal was discovered in the early 1950s near Picacho. In some areas of the state, groundwater-level declines of more than 150 m have resulted in extensive land subsidence and earth fissuring. Land subsidence in excess of 5.7 m has been documented in both western metropolitan Phoenix and Eloy. The Arizona Department of Water Resources (ADWR) has been monitoring land subsidence since 2002 using interferometric synthetic aperture radar (InSAR) and since 1998 using a global navigation satellite system (GNSS). The ADWR InSAR program has identified more than 25 individual land subsidence features that cover an area of more than 7,300 km2. Using InSAR data in conjunction with groundwater-level datasets, ADWR is able to monitor land subsidence areas as well as identify areas that may require additional monitoring. One area of particular concern is the Willcox groundwater basin in southeastern Arizona, which is the focus of this paper. The area is experiencing rapid groundwater declines, as much as 32.1 m during 2005-2014 (the largest land subsidence rate in Arizona State—up to 12 cm/year), and a large number of earth fissures. The declining groundwater levels in Arizona are a challenge for both future groundwater availability and mitigating land subsidence associated with these declines. ADWR's InSAR program will continue to be a critical tool for monitoring land subsidence due to excessive groundwater withdrawal.

Endoscopic endonasal anatomy of superior orbital fissure and orbital apex regions: critical considerations for clinical applications.

Science.gov (United States)

Dallan, Iacopo; Castelnuovo, Paolo; de Notaris, Matteo; Sellari-Franceschini, Stefano; Lenzi, Riccardo; Turri-Zanoni, Mario; Battaglia, Paolo; Prats-Galino, Alberto

2013-05-01

The superior orbital fissure is a critical three-dimensional space connecting the middle cranial fossa and the orbit. From an endoscopic viewpoint, only the medial aspect has a clinical significance. It presents a critical relationship with the lateral sellar compartment, the pterygopalatine fossa and the middle cranial fossa. The connective tissue layers and neural and vascular structures of this region are described. The role of Muller's muscle is confirmed, and the utility of the maxillary and optic strut is outlined. Muller's muscle extends for the whole length of the inferior orbital fissure, passes over the maxillary strut and enters the superior orbital fissure, representing a critical surgical landmark. Dividing the tendon between the medial and inferior rectus muscle allows the identification of the main trunk of the oculomotor nerve, and a little laterally, it is usually possible to visualize the first part of the ophthalmic artery. Based on a better knowledge of anatomy, we trust that this area could be readily addressed in clinical situations requiring an extended approach in proximity of the orbital apex.

Superior vesical fissure concealed by giant omphalocele: A case report

OpenAIRE

Hayek, Danial; Massanyi, Eric; Mancuso, Melissa; Krepkovich, Katherine; Garrison, Aaron

2016-01-01

Omphalocele is an abdominal wall defect characterized by exteriorization of abdominal viscera that is covered by a membrane. Omphalocele has a well-known association with chromosome abnormalities. Here we present a case of a superior vesical fissure (SVF) initially disguised as a giant omphalocele in a newborn with trisomy 18. We also show unique prenatal imaging and discuss the importance and limitations of prenatal genetic testing.

Salt geologic evaluation of the impact of cryogenic fissures and halokinetic deformation processes on the integrity of the geological barrier of the salt dome Gorleben

International Nuclear Information System (INIS)

Hammer, Joerg; Fleig, Stephanie; Mingerzahn, Gerhard

2012-07-01

In several salt domes of the area close to Hannover fissures were observed that might be caused by thermally induced fissure formation due to cold periods (cryogenic fissures). Comprehensive substantial-structural analyses are performed as an example for the salt dome Bokeloh with respect to genesis and transferability to the salt dome Gorleben. Based on recent structure-geological, mineralogical-geochemical and micro-paleontological studies and thermo-mechanical modeling a solely thermally induced fissure formation due to cold periods is unlikely for the salt dome Bokeloh. There is a direct relation between the genesis of the salt dome Bokeloh, its regional tectonic site and the fissure formation. Due to the completely different genesis and another regional-tectonic situation the existence of cryogenic fissures is excluded for the salt dome Gorleben. The salt-geologic and experimental studies on the deformation of anhydrite layers in salt domes are summarized and evaluated with respect to the long-term consequences for a potential final repository for high-level heat-generating radioactive waste in the salt dome Gorleben. The studies confirm the older BGR studies that anhydrite layers do not represent hydraulic potential ling-distance liquid paths.

Macrofauna of shallow hydrothermal vents on the Arctic Mid-Ocean Ridge at 71N

Science.gov (United States)

Schander, C.; Rapp, H. T.; Pedersen, R. B.

2007-12-01

Deep-sea hydrothermal vents are usually associated with a highly specialized fauna and since their discovery in 1977, more than 400 species of animals have been described. Specialized vent fauna includes various animal phyla, but the most conspicuous and well known are annelids, mollusks and crustaceans. We have investigated the fauna collected around newly discovered hydrothermal vents on the Mohns Ridge north of Jan Mayen. The venting fields are located at 71°N and the venting takes place within two main areas separated by 5 km. The shallowest vent area is at 500-550 m water depth and is located at the base of a normal fault. This vent field stretches approximately 1 km along the strike of the fault, and it is composed of 10-20 major vent sites each with multiple chimney constructions discharging up to 260°C hot fluids. A large area of diffuse, low- temperature venting occurs in the area surrounding the high-temperature field. Here, partly microbial mediated iron-oxide-hydroxide deposits are abundant. The hydrothermal vent sites do not show any high abundance of specialized hydrothermal vent fauna. Single groups (i.e. Porifera and Mollusca) have a few representatives but groups otherwise common in hydrothermal vent areas (e.g. vestimentifera, Alvinellid worms, mussels, clams, galathaeid and brachyuran crabs) are absent. Up until now slightly more than 200 species have been identified from the vent area. The macrofauna found in the vent area is, with few exceptions, an assortment of bathyal species known in the area. One endemic, yet undescribed, species of mollusc has been found so far, an gastropod related to Alvania incognita Warén, 1996 and A. angularis Warén, 1996 (Rissoidae), two species originally described from pieces of sunken wood north and south of Iceland. It is by far the most numerous mollusc species at the vents and was found on smokers, in the bacterial mats, and on the ferric deposits. A single specimen of an undescribed tanaidacean has also

14 CFR 34.11 - Standard for fuel venting emissions.

Science.gov (United States)

2010-01-01

... Emissions (New and In-Use Aircraft Gas Turbine Engines) § 34.11 Standard for fuel venting emissions. (a) No fuel venting emissions shall be discharged into the atmosphere from any new or in-use aircraft gas... include one of the following: (1) Incorporation of an FAA-approved system that recirculates the fuel back...

Pito Seamount revisited: the discovery and mapping of new black smoker vents

Science.gov (United States)

Cheadle, M. J.; John, B. E.; German, C. R.; Gee, J. S.; Coogan, L. A.; Gillis, K. M.; Swapp, S.

2017-12-01

In February 2017, the RV Atlantis PMaG (PaleoMagnetism and Gabbro) cruise re-visited a black smoker site originally discovered 24 years ago on Pito Seamount, by the submersible Nautile during the French Pito expedition (1993). Pito Seamount (111.639oW, 23.333oS) marks the northern tip of the propagating East Pacific Rise, bounding the east side of the Easter Microplate. There the seafloor rises to 2250mbsl and has a 900m wide, 50m deep axial valley, which hosts at least two separate fields of active hydrothermal vents. AUV Sentry mapping of the summit of Pito seamount (0.5-1m resolution) highlights over 50 active and inactive chimneys amid recent basaltic sheet flows, pillow mounds and ponded lava. The vents occur in two fields/sub-fields; the first covers an area of 800 x 200m, and lies parallel to the ridge axis, along incipient faults forming on the northeastern flank of the axial valley. The second field occurs in a 250m diameter area in the centre of the axial valley. Jason II dive 961 visited, sampled, measured vent orifice temperatures, and acquired 4k video of the chimneys, and re-discovered the active (Magnificent Village) vent first found by Nautile, in the now named Nautile vent field, together with five additional active hydrothermal vents (Jason, Medea, Sentry, Abe and Scotty's Castle). The Magnificent Village, the largest active vent, is 25m tall and has multiple active spires in three main groups surrounding a hollow amphitheater. Measured vent orifice temperatures ranged from 338oC (Magnificent Village) to 370oC (Jason). The vents host a fauna of alvinellid worms, bythograidid crabs, alvincardid shrimps, phymorhynchus gastropods, Corallimorphid anenomes and bathymodiolid mussels, but no vestimentiferan worms. Brisingid brittle stars colonize inactive chimneys.

A New Approach to Uncertainty Reduction in Launch Vehicle Compartment Venting

Data.gov (United States)

National Aeronautics and Space Administration — Launch vehicle compartments are vented to the external environment during ascent to minimize undesirable structural loading. Prediction of venting performance is an...

E-njoy the first CERN Global Network e-vent!

CERN Multimedia

CERN Bulletin

2010-01-01

Empowered by the considerable interest it received after it was launched, the CERN Global Network takes off and organizes the first e-vent, which will be a special talk on science communication that will be held on 29 June at 4.30 p.m. in the Council Chamber. You can experience it live on the Global Network site and, if you are a Member, provide feedback. Stay linked!   On the CERN Global Network webpage, you will be able to choose the topic of the next e-vents. Seven weeks after its launch, about 600 people have already joined the CERN Global Network and six thematic groups have been created. The whole idea of joining the Network is to stay connected or reconnect with life at CERN where seminars, talks and discussions are undoubtedly a very important and much appreciated part of it. This is where the e-vents come into play. “The e-vents enable members of the Global Network to participate in selected events taking place at CERN, such as lectures or panel discussions. They will...

Desenvolvimento das fissuras cerebrais fetais: avaliação com ultrassonografia tridimensional Fetal brain fissures development a three-dimensional ultrasonography study

Directory of Open Access Journals (Sweden)

Cynthia Maria Soares Alves

2011-03-01

Full Text Available OBJETIVO: avaliar a distância das fissuras cerebrais fetais à borda interna da calota craniana por meio da ultrassonografia tridimensional (US3D. MÉTODOS: realizou-se um estudo de corte transversal em 80 gestantes normais entre a 21ª e 34ª semanas de gestação. Avaliou-se a distância entre a tábua óssea interna da calota craniana fetal e as fissuras de Sylvius, parieto-occipital, hipocampo e calcarina. Para a obtenção desta distância para as três primeiras fissuras, realizou-se uma varredura tridimensional através do plano axial (nível dos ventrículos laterais. Para a obtenção da distância da fissura calcarina utilizou-se uma varredura coronal (nível dos lobos occiptais. Para avaliar a correlação entre as fissuras e a idade gestacional foram realizadas regressões de primeiro grau, sendo os ajustes calculados pelo coeficiente de determinação (R². Foram determinados percentis 5, 50 e 95 para cada fissura. Avaliou-se ainda a correlação entre a distância destas fissuras com os diâmetros biparietal (DBP e circunferência craniana (CC utilizando o coeficiente de correlação de Pearson (r. RESULTADOS: todas as medidas das fissuras apresentaram correlação linear com a idade gestacional (Sylvius: R²=0,5; parieto-occipital: R²=0,7; hipocampo: R²=0,3 e calcarina: R²=0,3. A média da distância das fissuras variou de 7,0 a 14,0 mm, 15,9 a 28,7 mm, 15,4 a 25,4 mm e 15,7 a 24,8 mm para as fissuras de Sylvius, parieto-occipital, hipocampo e calcarina, respectivamente. As fissuras de Sylvius e parieto-occipital apresentaram as maiores correlações com o DBP (r=0,8 e 0,7, respectivamente e a CC (r=0,7 e 0,8, respectivamente. CONCLUSÕES: a distância das fissuras cerebrais fetais à borda interna da calota craniana por meio da US3D apresentou correlação positiva com a idade gestacional.PURPOSE: to assess the distance of the fetal cerebral fissures from the inner edge of the skull by three-dimensional ultrasonography (3DUS

Hydrothermal Vents and Methane Seeps: Rethinking the Sphere of Influence

Directory of Open Access Journals (Sweden)

Lisa Ann Levin

2016-05-01

Full Text Available Although initially viewed as oases within a barren deep ocean, hydrothermal vent and methane seep communities are now recognized to interact with surrounding ecosystems on the sea floor and in the water column, and to affect global geochemical cycles. The importance of understanding these interactions is growing as the potential rises for disturbance from oil and gas extraction, seabed mining and bottom trawling. Here we synthesize current knowledge of the nature, extent and time and space scales of vent and seep interactions with background systems. We document an expanded footprint beyond the site of local venting or seepage with respect to elemental cycling and energy flux, habitat use, trophic interactions, and connectivity. Heat and energy are released, global biogeochemical and elemental cycles are modified, and particulates are transported widely in plumes. Hard and biotic substrates produced at vents and seeps are used by benthic background fauna for attachment substrata, shelter, and access to food via grazing or through position in the current, while particulates and fluid fluxes modify planktonic microbial communities. Chemosynthetic production provides nutrition to a host of benthic and planktonic heterotrophic background species through multiple horizontal and vertical transfer pathways assisted by flow, gamete release, animal movements, and succession, but these pathways remain poorly known. Shared species, genera and families indicate that ecological and evolutionary connectivity exists among vents, seeps, organic falls and background communities in the deep sea; the genetic linkages with inactive vents and seeps and background assemblages however, are practically unstudied. The waning of venting or seepage activity generates major transitions in space and time that create links to surrounding ecosystems, often with identifiable ecotones or successional stages. The nature of all these interactions is dependent on water depth, as

Hydrothermal vents and methane seeps: Rethinking the sphere of influence

Science.gov (United States)

Levin, Lisa A.; Baco, Amy; Bowden, David; Colaco, Ana; Cordes, Erik E.; Cunha, Marina; Demopoulos, Amanda W.J.; Gobin, Judith; Grupe, Ben; Le, Jennifer; Metaxas, Anna; Netburn, Amanda; Rouse, Greg; Thurber, Andrew; Tunnicliffe, Verena; Van Dover, Cindy L.; Vanreusel, Ann; Watling, Les

2016-01-01

Although initially viewed as oases within a barren deep ocean, hydrothermal vent and methane seep communities are now recognized to interact with surrounding ecosystems on the sea floor and in the water column, and to affect global geochemical cycles. The importance of understanding these interactions is growing as the potential rises for disturbance from oil and gas extraction, seabed mining and bottom trawling. Here we synthesize current knowledge of the nature, extent and time and space scales of vent and seep interactions with background systems. We document an expanded footprint beyond the site of local venting or seepage with respect to elemental cycling and energy flux, habitat use, trophic interactions, and connectivity. Heat and energy are released, global biogeochemical and elemental cycles are modified, and particulates are transported widely in plumes. Hard and biotic substrates produced at vents and seeps are used by “benthic background” fauna for attachment substrata, shelter, and access to food via grazing or through position in the current, while particulates and fluid fluxes modify planktonic microbial communities. Chemosynthetic production provides nutrition to a host of benthic and planktonic heterotrophic background species through multiple horizontal and vertical transfer pathways assisted by flow, gamete release, animal movements, and succession, but these pathways remain poorly known. Shared species, genera and families indicate that ecological and evolutionary connectivity exists among vents, seeps, organic falls and background communities in the deep sea; the genetic linkages with inactive vents and seeps and background assemblages however, are practically unstudied. The waning of venting or seepage activity generates major transitions in space and time that create links to surrounding ecosystems, often with identifiable ecotones or successional stages. The nature of all these interactions is dependent on water depth, as well as

Superior vesical fissure concealed by giant omphalocele: A case report

Directory of Open Access Journals (Sweden)

Danial Hayek

2016-11-01

Full Text Available Omphalocele is an abdominal wall defect characterized by exteriorization of abdominal viscera that is covered by a membrane. Omphalocele has a well-known association with chromosome abnormalities. Here we present a case of a superior vesical fissure (SVF initially disguised as a giant omphalocele in a newborn with trisomy 18. We also show unique prenatal imaging and discuss the importance and limitations of prenatal genetic testing.

Microleakage assessment of fissure sealant following fissurotomy bur or pumice prophylaxis use before etching

Directory of Open Access Journals (Sweden)

Ali Bagherian

2013-01-01

The aim of this investigation was to compare the microleakage level of fissure sealants prepared by a fissurotomy bur or pumice prophylaxis prior to acid etching. Materials and Methods: Ninety freshly extracted healthy maxillary premolar teeth were randomly selected for this investigation. Teeth were then divided into three fissure sealant preparatory groups of A: Fissurotomy bur + acid etch; B: Pumice prophylaxis + acid etch and C: Acid etch alone. Sealant was applied to the occlusal fissures of all specimens using a plastic instrument. This was to avoid any air trap under the sealant. Sample teeth were first thermocycled (1000 cycles, 20 s dwell time and then coated with two layers of nail varnish leaving 2 mm around the sealant. This was then followed by immersion in basic fuchsin 3%. Processed teeth were sectioned longitudinally and examined under a stereomicroscope for microleakage assessment using a score of 0-3. Collected data was then subjected to Kruskall-Wallis Analysis of Variance and Mann-Whitney U-test. P < 0.05 was considered as significant. Results: Teeth in fissurotomy bur and pumice prophylaxis groups had significantly reduced level of microleakage than those in acid etch alone (P = 0.005 and P = 0.003, respectively. Conclusion: Use of fissurotomy bur and pumice prophylaxis accompanied with acid etching appears to have a more successful reduction of microleakage than acid etch alone.

Biogeography of Persephonella in deep-sea hydrothermal vents of the Western Pacific.

Directory of Open Access Journals (Sweden)

Sayaka eMino

2013-04-01

Full Text Available Deep-sea hydrothermal vent fields are areas on the seafloor with high biological productivity fueled by microbial chemosynthesis. Members of the Aquificales genus Persephonella are obligately chemosynthetic bacteria, and appear to be key players in carbon, sulfur, and nitrogen cycles in high temperature habitats at deep-sea vents. Although this group of bacteria has cosmopolitan distribution in deep-sea hydrothermal ecosystem around the world, little is known about their population structure such as intraspecific genomic diversity, distribution pattern, and phenotypic diversity. We developed the multi-locus sequence analysis (MLSA scheme for their genomic characterization. Sequence variation was determined in five housekeeping genes and one functional gene of 36 P. hydrogeniphila strains originated from the Okinawa Trough and the South Mariana Trough. Although the strains share > 98.7% similarities in 16S rRNA gene sequences, MLSA revealed 35 different sequence types, indicating their extensive genomic diversity. A phylogenetic tree inferred from all concatenated gene sequences revealed the clustering of isolates according to the geographic origin. In addition, the phenotypic clustering pattern inferred from whole-cell matrix-assisted laser desorption ionization-time of flight mass spectrometry (MALDI-TOF/MS analysis can be correlated to their MLSA clustering pattern. This study represents the first MLSA combined with phenotypic analysis indicative of allopatric speciation of deep-sea hydrothermal vent bacteria.

Spatial scaling of bacterial community diversity at shallow hydrothermal vents: a global comparison

Science.gov (United States)

Pop Ristova, P.; Hassenrueck, C.; Molari, M.; Fink, A.; Bühring, S. I.

2016-02-01

Marine shallow hydrothermal vents are extreme environments, often characterized by discharge of fluids with e.g. high temperatures, low pH, and laden with elements toxic to higher organisms. They occur at continental margins around the world's oceans, but represent fragmented, isolated habitats of locally small areal coverage. Microorganisms contribute the main biomass at shallow hydrothermal vent ecosystems and build the basis of the food chain by autotrophic fixation of carbon both via chemosynthesis and photosynthesis, occurring simultaneously. Despite their importance and unique capacity to adapt to these extreme environments, little is known about the spatial scales on which the alpha- and beta-diversity of microbial communities vary at shallow vents, and how the geochemical habitat heterogeneity influences shallow vent biodiversity. Here for the first time we investigated the spatial scaling of microbial biodiversity patterns and their interconnectivity at geochemically diverse shallow vents on a global scale. This study presents data on the comparison of bacterial community structures on large (> 1000 km) and small (0.1 - 100 m) spatial scales as derived from ARISA and Illumina sequencing. Despite the fragmented global distribution of shallow hydrothermal vents, similarity of vent bacterial communities decreased with geographic distance, confirming the ubiquity of distance-decay relationship. Moreover, at all investigated vents, pH was the main factor locally structuring these communities, while temperature influenced both the alpha- and beta-diversity.

Visualization of the air flow behind the automotive benchmark vent

Science.gov (United States)

Pech, Ondrej; Jedelsky, Jan; Caletka, Petr; Jicha, Miroslav

2015-05-01

Passenger comfort in cars depends on appropriate function of the cabin HVAC system. A great attention is therefore paid to the effective function of automotive vents and proper formation of the flow behind the ventilation outlet. The article deals with the visualization of air flow from the automotive benchmark vent. The visualization was made for two different shapes of the inlet channel connected to the benchmark vent. The smoke visualization with the laser knife was used. The influence of the shape of the inlet channel to the airflow direction, its enlargement and position of air flow axis were investigated.

Visualization of the air flow behind the automotive benchmark vent

Directory of Open Access Journals (Sweden)

Pech Ondrej

2015-01-01

Full Text Available Passenger comfort in cars depends on appropriate function of the cabin HVAC system. A great attention is therefore paid to the effective function of automotive vents and proper formation of the flow behind the ventilation outlet. The article deals with the visualization of air flow from the automotive benchmark vent. The visualization was made for two different shapes of the inlet channel connected to the benchmark vent. The smoke visualization with the laser knife was used. The influence of the shape of the inlet channel to the airflow direction, its enlargement and position of air flow axis were investigated.

Arsenic speciation in food chains from mid-Atlantic hydrothermal vents

Science.gov (United States)

Taylor, Vivien F.; Jackson, Brian P.; Siegfried, Matthew R.; Navratilova, Jana; Francesconi, Kevin A.; Kirshtein, Julie; Voytek, Mary

2012-01-01

Arsenic concentration and speciation were determined in benthic fauna collected from the Mid-Atlantic Ridge hydrothermal vents. The shrimp species, Rimicaris exoculata, the vent chimney-dwelling mussel, Bathymodiolus azoricus, Branchipolynoe seepensis, a commensal worm of B. azoricus and the gastropod Peltospira smaragdina showed variations in As concentration and in stable isotope (δ13C and δ15N) signature between species, suggesting different sources of As uptake. Arsenic speciation showed arsenobetaine to be the dominant species in R. exoculata, whereas in B. azoricus and B. seepensis arsenosugars were most abundant, although arsenobetaine, dimethylarsinate and inorganic arsenic were also observed, along with several unidentified species. Scrape samples from outside the vent chimneys covered with microbial mat, which is a presumed food source for many vent organisms, contained high levels of total As, but organic species were not detectable. The formation of arsenosugars in pelagic environments is typically attributed to marine algae, and the pathway to arsenobetaine is still unknown. The occurrence of arsenosugars and arsenobetaine in these deep sea organisms, where primary production is chemolithoautotrophic and stable isotope analyses indicate food sources are of vent origin, suggests that organic arsenicals can occur in a foodweb without algae or other photosynthetic life.

Arsenic speciation in food chains from mid-Atlantic hydrothermal vents.

Science.gov (United States)

Taylor, Vivien F; Jackson, Brian P; Siegfried, Matthew; Navratilova, Jana; Francesconi, Kevin A; Kirshtein, Julie; Voytek, Mary

2012-05-04

Arsenic concentration and speciation were determined in benthic fauna collected from the Mid-Atlantic Ridge hydrothermal vents. The shrimp species, Rimicaris exoculata , the vent chimney-dwelling mussel, Bathymodiolus azoricus , Branchipolynoe seepensis , a commensal worm of B. azoricus , and the gastropod Peltospira smaragdina showed variations in As concentration and in stable isotope (δ 13 C and δ 15 N) signature between species, suggesting different sources of As uptake. Arsenic speciation showed arsenobetaine to be the dominant species in R. exoculata , whereas in B. azoricus and B. seepensis arsenosugars were most abundant, although arsenobetaine, dimethylarsinate, and inorganic arsenic were also observed, along with several unidentified species. Scrape samples from outside the vent chimneys, covered with microbial mat, which is a presumed food source for many vent organisms, contained high levels of total As, but organic species were not detectable. The formation of arsenosugars in pelagic environments is typically attributed to marine algae, and the pathway to arsenobetaine is still unknown. The occurrence of arsenosugars and arsenobetaine in these deep sea organisms, where primary production is chemolithoautotrophic and stable isotope analyses indicate food sources are of vent origin, suggests that organic arsenicals can occur in a food web without algae or other photosynthetic life.

Microbiological characterization of post-eruption "snowblower" vents at Axial Seamount, Juan de Fuca Ridge

Directory of Open Access Journals (Sweden)

Julie L Meyer

2013-06-01

Full Text Available Microbial processes within the subseafloor can be examined during the ephemeral and uncommonly observed phenomena known as snowblower venting. Snowblowers are characterized by the large quantity of white floc that is expelled from the seafloor following mid-ocean ridge eruptions. During these eruptions, rapidly cooling lava entrains seawater and hydrothermal fluids enriched in geochemical reactants, creating a natural bioreactor that supports a subseafloor microbial bloom. Previous studies hypothesized that the eruption-associated floc is made by sulfide-oxidizing bacteria; however, the microbes involved were never identified. Here we present the first molecular analysis combined with microscopy of microbial communities in snowblower vents from samples collected shortly after the 2011 eruption at Axial Seamount, an active volcano on the Juan de Fuca Ridge. We obtained fluid samples and white flocculent material from active snowblower vents as well as orange flocculent material found on top of newly formed lava flows. Both flocculent types revealed diverse cell types and particulates when examined by phase contrast and scanning electron microscopy. Distinct archaeal and bacterial communities were detected in each sample type through Illumina tag sequencing of 16S rRNA genes and through sequencing of the sulfide oxidation gene, soxB. In fluids and white floc, the dominant bacteria were sulfur-oxidizing Epsilonproteobacteria and the dominant archaea were thermophilic Methanococcales. In contrast, the dominant organisms in the orange floc were Gammaproteobacteria and Thaumarchaeota Marine Group I. In all samples, bacteria greatly outnumbered archaea. The presence of anaerobic methanogens and microaerobic Epsilonproteobacteria in snowblower communities provides evidence that these blooms are seeded by subseafloor microbes, rather than from microbes in bottom seawater. These eruptive events thus provide a unique opportunity to observe subseafloor

Geologic evolution of the Lost City Hydrothermal Field

Science.gov (United States)

Denny, Alden R.; Kelley, Deborah S.; Früh-Green, Gretchen L.

2016-02-01

The Lost City Hydrothermal Field (LCHF) is a novel serpentinite-hosted vent field located on the Atlantis Massif southern wall. Results of 2 m resolution bathymetry, side scan, and video and still imagery, integrated with direct submersible observations provide the first high-resolution geologic map of the LCHF. These data form the foundation for an evolutionary model for the vent system over the past >120,000 years. The field is located on a down-dropped bench 70 m below the summit of the massif. The bench is capped by breccia and pelagic carbonate deposits underlain by variably deformed and altered serpentinite and gabbroic rocks. Hydrothermal activity is focused at the 60 m tall, 100 m across, massive carbonate edifice "Poseidon," which is venting 91°C fluid. Hydrothermal activity declines south and west of the Poseidon complex and dies off completely at distances greater than 200 m. East of Poseidon, the most recent stage of hydrothermal flow is characterized by egress of diffuse fluids from narrow fissures within a low-angle, anastomosing mylonite zone. South of the area of current hydrothermal activity, there is evidence of two discrete previously unrecognized relict fields. Active venting sites defined by carbonate-filled fissures that cut the carbonate cap rock at the summit of the massif mark the present-day northernmost extent of venting. These spatial relationships reflect multiple stages of field development, the northward migration of venting over time, and the likely development of a nascent field at the massif summit.

Giant desiccation fissures on the Black Rock and Smoke Creek Deserts, Nevada

Science.gov (United States)

Willden, R.; Mabey, D.R.

1961-01-01

Open fissures, from 100 to several hundred feet apart, that have produced polygonal patterns on the Black Rock Desert, Nevada, are believed to be giant desiccation cracks resulting from a secular trend toward aridity in the last few decades. Similar features on the Smoke Creek Desert probably have the same origin.

Toward an integrated genetic model for vent-distal SEDEX deposits

Science.gov (United States)

Sangster, D. F.

2018-04-01

Although genetic models have been proposed for vent-proximal SEDEX deposits, an equivalent model for vent-distal deposits has not yet appeared. In view of this, it is the object of this paper to present a preliminary integrated vent-distal genetic model through exploration of four major components: (i) nature of the ore-forming fluid, (ii) role of density of the unconsolidated host sediments, (iii) dynamics of sulfate reduction and (iv) depositional environment. Two sub-groups of SEDEX Pb-Zn deposits, vent-proximal and vent-distal, are widely recognized today. Of the two, the latter is by far the largest in terms of metal content with each of the 13 largest containing in excess of 7.5 M (Zn+Pb) metal. In contrast, only one vent-proximal deposit (Sullivan) falls within this size range. Vent-proximal deposits are characteristically underlain by local networks of sulfide-filled veins (commonly regarded as feeder veins) surrounded by a discordant complex of host rock alteration. These attributes are missing in vent-distal deposits, which has led to the widespread view that vent-distal ore-forming fluids have migrated unknown distances away from their vent sites. Because of the characteristic fine grain size of ore minerals, critical fluid inclusion data are lacking for vent-distal ore-stage sulfides. Consequently, hypothetical fluids such as those which formed MVT deposits (120 °C, 20% NaCl equiv.) are considered to represent vent-distal fluids as well. Such high-salinity fluids are capable of carrying significant concentrations of Pb and Zn as chloride complexes while the relatively low temperatures preclude high Cu contents. Densities of such metalliferous brines result in bottom-hugging fluids that collect in shallow saucer-shaped depressions (collector basins). Lateral metal zoning in several deposits reveals the direction from which the brines came. Relative densities of the ore-forming fluid and sediment determine whether the ore-forming fluid stabilizes on top

40 CFR 63.113 - Process vent provisions-reference control technology.

Science.gov (United States)

2010-07-01

... § 63.113 Process vent provisions—reference control technology. (a) The owner or operator of a Group 1... 40 Protection of Environment 9 2010-07-01 2010-07-01 false Process vent provisions-reference control technology. 63.113 Section 63.113 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY...

40 CFR 63.1322 - Batch process vents-reference control technology.

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 11 2010-07-01 2010-07-01 true Batch process vents-reference control technology. 63.1322 Section 63.1322 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR... Batch process vents—reference control technology. (a) Batch process vents. The owner or operator of a...

Venting krypton-85 from the Three Mile Island Unit 2 reactor building

International Nuclear Information System (INIS)

Burton, H.M.

1981-01-01

To permit the less restricted access to the reactor building necessary to maintain instrumentation and equipment, and to proceed towad the total decontamination of the facility, General Public Utilities, operators of the facility referred to hereafter as GPU, asked the United States Nuclear Regulatory Commission, or NRC, for permission to remove the 85 Kr from the reactor building by venting it to the environment. GPU supported their request with the Safety Analysis and Environmental Assessment Report on the proposed reactor building venting plan. On June 12, 1980, after seven months of licensing deliberations and numerous public hearings, the NRC granted GPU's request. The actual venting took place between June 28 and July 11, 1980. This report presents an overview of the detailed effort involved in the TMI-2 reactor building venting program. The findings reported here are condensed from a published report entitled TMI-2 Reactor Building Purge--Kr-85 Venting

A numerical study of the effect of vent flow angle on the heat transfer rate from a cold window with a below-window hot-air vent

Energy Technology Data Exchange (ETDEWEB)

Oosthuizen, P.H. [Queen' s Univ., Kingston, ON (Canada). Dept. of Mechanical and Materials Engineering

2010-07-01

This study investigated the effects of the discharge angle on air leaving a hot air vent mounted below a window. The window was represented by a plane isothermal section recessed into a wall and was colder than air in the rest of the room. The vent was placed against the wall and had a uniform discharge velocity. Flow was assumed to be steady. Both laminar and turbulent flows were evaluated using a commercial computational fluid dynamics (CFD) simulation tool. A k-epsilon turbulence model was used to determine turbulent flow calculations. The study determined the Rayleigh number based on window height, the Reynolds number based on the vent discharge velocity, the angle of the vent discharge flow, the Prandtl number, and dimensionless vent discharge temperature differences. The study showed that a relatively thin layer of cold air adjacent to the floor is present at high Rayleigh numbers, where the downward natural convective flow over the window dominates the overall flow. At low Rayleigh numbers, the cold air flows upward towards the ceiling and temperatures in the room are nearly uniform. 47 refs., 11 figs.

Soil gas geochemistry in relation to eruptive fissures on Timanfaya volcano, Lanzarote Island (Canary Islands, Spain)

Science.gov (United States)

Padrón, Eleazar; Padilla, Germán; Hernández, Pedro A.; Pérez, Nemesio M.; Calvo, David; Nolasco, Dácil; Barrancos, José; Melián, Gladys V.; Dionis, Samara; Rodríguez, Fátima

2013-01-01

We report herein the first results of an extensive soil gas survey performed on Timanfaya volcano on May 2011. Soil gas composition at Timanfaya volcano indicates a main atmospheric source, slightly enriched in CO2 and He. Soil CO2 concentration showed a very slight deep contribution of the Timanfaya volcanic system, with no clear relation to the main eruptive fissures of the studied area. The existence of soil helium enrichments in Timanfaya indicates a shallow degassing of crustal helium and other possible deeper sources probably form cooling magma bodies at depth. The main soil helium enrichments were observed in good agreement with the main eruptive fissures of the 1730-36 eruption, with the highest values located at those areas with a higher density of recent eruptive centers, indicating an important structural control for the leakage of helium at Timanfaya volcano. Atmospheric air slightly polluted by deep-seated helium emissions, CO2 degassed from a cooling magma body, and biogenic CO2, might be the most plausible explanation for the existence of soil gas. Helium is a deep-seated gas, exhibiting important emission rates along the main eruptive fissure of the 1730-36 eruption of Timanfaya volcano.

Geophysical Signatures of cold vents on the northern Cascadia margin

Science.gov (United States)

Riedel, M.; Paull, C. K.; Spence, G.; Hyndman, R. D.; Caress, D. W.; Thomas, H.; Lundsten, E.; Ussler, W.; Schwalenberg, K.

2009-12-01

The accretionary prism of the northern Cascadia margin is a classic gas hydrate research area. Ocean Drilling Program Leg 146 and Integrated Ocean Drilling Program (IODP) Expedition 311 documented that gas hydrate is widely distributed across the margin. In recent years an increased research focus has been on cold vents, where methane gas is actively released. Two recent expeditions funded by the Monterey Bay Aquarium Research Institute (MBARI) were conducted in the area of IODP Sites U1327 and U1328. An autonomous underwater vehicle (AUV) was used to map the seafloor bathymetry followed by dives with the ROV Doc Ricketts for ground truth information of various seafloor morphological features identified. The two cruises revealed many new seafloor features indicative of methane venting that were previously unknown. Bullseye Vent (BV) has been extensively studied using seismic imaging, piston coring, heat-flow, controlled-source EM, and deep drilling. BV is seismically defined by a circular wipe-out zone but the new AUV data show that BV is rather an elongated depression. BV is associated with a shoaling in the BSR, but lacks evidence for the existence of an underlying fault in the previous data. Although a massive gas-hydrate plug was encountered within the top 40 mbsf in the IODP holes, the ROV observations only revealed some platy methane derived carbonate outcrops at the outer-most rim of the depressions, a few beds of Vesicomya clams, and no observed gas vents, which together do not indicate that BV is especially active now. Further northeast of BV, but along the same trend, active gas venting was found associated with seafloor blistering and bacterial mats suggesting that there is an underlying fault system providing a fluid flow conduit. The newly discovered vent area has few seismic line crossings; however the available seismic data surprisingly are not associated with wipe-out zones. Another prominent fault-related gas vent also was investigated during the

Emergency venting of pressure vessels

International Nuclear Information System (INIS)

Steinkamp, H.

1995-01-01

With the numerical codes developed for safety analysis the venting of steam vessel can be simulated. ATHLET especially is able to predict the void fraction depending on the vessel height. Although these codes contain a one-dimensional model they allow the description of complex geometries due to the detailed nodalization of the considered apparatus. In chemical reactors, however, the venting process is not only influenced by the flashing behaviour but additionally by the running chemical reaction in the vessel. Therefore the codes used for modelling have to consider the kinetics of the chemical reaction. Further multi-component systems and dissolving processes have to be regarded. In order to preduct the fluid- and thermodynamic process it could be helpful to use 3-dimensional codes in combination with the one-dimensional codes as used in nuclear industry to get a more detailed describtion of the running processes. (orig./HP)

Rice fissure resistance QTLs from ‘Saber’ complement those from ‘Cypress’

Science.gov (United States)

The economic value of broken rice is about half that of whole milled rice, so one goal of producers, millers, and rice breeders is to reduce grain breakage during the dehusking and milling processes. One of the primary causes of rice breakage is fissuring, or cracking, of the rice before it enters ...

Analysis of sound absorption performance of an electroacoustic absorber using a vented enclosure

Science.gov (United States)

Cho, Youngeun; Wang, Semyung; Hyun, Jaeyub; Oh, Seungjae; Goo, Seongyeol

2018-03-01

The sound absorption performance of an electroacoustic absorber (EA) is primarily influenced by the dynamic characteristics of the loudspeaker that acts as the actuator of the EA system. Therefore, the sound absorption performance of the EA is maximum at the resonance frequency of the loudspeaker and tends to degrade in the low-frequency and high-frequency bands based on this resonance frequency. In this study, to adjust the sound absorption performance of the EA system in the low-frequency band of approximately 20-80 Hz, an EA system using a vented enclosure that has previously been used to enhance the radiating sound pressure of a loudspeaker in the low-frequency band, is proposed. To verify the usefulness of the proposed system, two acoustic environments are considered. In the first acoustic environment, the vent of the vented enclosure is connected to an external sound field that is distinct from the sound field coupled to the EA. In this case, the acoustic effect of the vented enclosure on the performance of the EA is analyzed through an analytical approach using dynamic equations and an impedance-based equivalent circuit. Then, it is verified through numerical and experimental approaches. Next, in the second acoustic environment, the vent is connected to the same external sound field as the EA. In this case, the effect of the vented enclosure on the EA is investigated through an analytical approach and finally verified through a numerical approach. As a result, it is confirmed that the characteristics of the sound absorption performances of the proposed EA system using the vented enclosure in the two acoustic environments considered in this study are different from each other in the low-frequency band of approximately 20-80 Hz. Furthermore, several case studies on the change tendency of the performance of the EA using the vented enclosure according to the critical design factors or vent number for the vented enclosure are also investigated. In the future

40 CFR 63.765 - Glycol dehydration unit process vent standards.

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 10 2010-07-01 2010-07-01 false Glycol dehydration unit process vent... Facilities § 63.765 Glycol dehydration unit process vent standards. (a) This section applies to each glycol dehydration unit subject to this subpart with an actual annual average natural gas flowrate equal to or...

40 CFR 63.1275 - Glycol dehydration unit process vent standards.

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 11 2010-07-01 2010-07-01 true Glycol dehydration unit process vent... Facilities § 63.1275 Glycol dehydration unit process vent standards. (a) This section applies to each glycol dehydration unit subject to this subpart with an actual annual average natural gas flowrate equal to or...

Experimental investigation on No-Vent Fill (NVF) process using liquid Nitrogen

International Nuclear Information System (INIS)

Kim, Young Cheol; Seo, Man Su; Yoo, Dong Gyu; Jeong, Sang Kwon

2014-01-01

For a long-term space mission, filling process of cryogenic liquid propellant is operated on a space vehicle in space. A vent process during transfer and filling of cryogenic propellant is needed to maintain the fuel tank pressure at a safe level due to its volatile characteristic. It is possible that both liquid and vapor phases of the cryogenic propellant are released simultaneously to outer space when the vent process occurs under low gravity environment. As a result, the existing filling process with venting not only accompanies wasting liquid propellant, but also consumes extra fuel to compensate for the unexpected momentum originated from the vent process. No-Vent Fill (NVF) method, a filling procedure without a venting process of cryogenic liquid propellant, is an attractive technology to perform a long-term space mission. In this paper, the preliminary experimental results of the NVF process are described. The experimental set-up consists of a 9-liter cryogenic liquid receiver tank and a supply tank. Liquid nitrogen (LN2) is used to simulate the behavior of cryogenic propellant. The whole situation in the receiver tank during NVF is monitored. The major experimental parameter in the experiment is the mass flow rate of the liquid nitrogen. The experimental results demonstrate that as the mass flow rate is increased, NVF process is conducted successfully. The quality and the inlet temperature of the injected LN2 are affected by the mass flow rate. These parameters determine success of NVF.

Analysis of containment venting for the Peach Bottom Atomic Power Station

International Nuclear Information System (INIS)

Hanson, D.J.; Wright, R.E.; Jenkins, J.P.

1986-01-01

The effectiveness of containment venting as a means of preventing or mitigating the consequences of severe accidents was evaluated for Peach Bottom Atomic Power Station Units 2 and 3 (BWR-4s with Mark I containments). Results from this evaluation indicate that the effectiveness of venting in preventing containment failure is highly dependent on the severe accident sequence. Containment venting can be effective for several classes of sequences, including loss-of-coolant accidents with breaks in the containment and transients with a failure of containment heat removal. However, based on draft procedures and equipment in place at the time of the evaluation, containment venting has limited potential for further reducing the risk associated with several sequences currently identified as significant contributors to risk. Means of improving the potential for risk reduction were identified, but their influence on risk was not analyzed

Degassing during magma ascent in the Mule Creek vent (USA)

Science.gov (United States)

Stasiuk, M.V.; Barclay, J.; Carroll, M.R.; Jaupart, Claude; Ratte, J.C.; Sparks, R.S.J.; Tait, S.R.

1996-01-01

The structures and textures of the rhyolite in the Mule Creek vent (New Mexico, USA) indicate mechanisms by which volatiles escape from silicic magma during eruption. The vent outcrop is a 300-m-high canyon wall comprising a section through the top of a feeder conduit, vent and the base of an extrusive lava dome. Field relations show that eruption began with an explosive phase and ended with lava extrusion. Analyses of glass inclusions in quartz phenocrysts from the lava indicate that the magma had a pre-eruptive dissolved water content of 2.5-3.0 wt% and, during eruption, the magma would have been water-saturated over the vertical extent of the present outcrop. However, the vesicularity of the rhyolite is substantially lower than that predicted from closed-system models of vesiculation under equilibrium conditions. At a given elevation in the vent, the volume fraction of primary vesicles in the rhyolite increases from zero close to the vent margin to values of 20-40 vol.% in the central part. In the centre the vesicularity increases upward from approximately 20 vol.% at 300 m below the canyon rim to approximately 40 vol.% at 200 m, above which it shows little increase. To account for the discrepancy between observed vesicularity and measured water content, we conclude that gas escaped during ascent, probably beginning at depths greater than exposed, by flow through the vesicular magma. Gas escape was most efficient near the vent margin, and we postulate that this is due both to the slow ascent of magma there, giving the most time for gas to escape, and to shear, favouring bubble coalescence. Such shear-related permeability in erupting magma is supported by the preserved distribution of textures and vesicularity in the rhyolite: Vesicles are flattened and overlapping near the dense margins and become progressively more isolated and less deformed toward the porous centre. Local zones have textures which suggest the coalescence of bubbles to form permeable

Containment venting as a mitigation technique for BWR MARK I plant ATWS

International Nuclear Information System (INIS)

Harrington, R.M.

1987-01-01

Containment venting is studied as a mitigation strategy for preventing or delaying severe fuel damage following hypothetical BWR Anticipated Transient Without Scram (ATWS) accidents initiated by MSIV-closure, and compounded by failure of the Standby Liquid Control (SLC) system injection of sodium pentaborate solution and by the failure of manually initiated control rod insertion. The venting of primary containment after reaching 75 psia (0.52 MPa) is found to result in the release of the vented steam inside the reactor building, and to result in inadequate Net Positive Suction Head (NPSH) for any system pumping from the pressure suppression pool. CONTAIN code calculations show that personnel access to large portions of the reactor building would be lost soon after the initiation of venting and that the temperatures reached would be likely to result in independent equipment failures. It is concluded that containment venting would be more likely to cause or to hasten the onset of severe fuel damage than to prevent or to delay it. Two alternative strategies that do not require containment venting, but that could delay or prevent severe fuel damage, are analyzed. BWR-LTAS code results are presented for a successful mitigation strategy in which the reactor vessel is depressurized, and for one in which the reactor vessel remains at pressure

Impact of vent pipe diameter on characteristics of waste degradation in semi-aerobic bioreactor landfill.

Science.gov (United States)

Jiang, Guobin; Liu, Dan; Chen, Weiming; Ye, Zhicheng; Liu, Hong; Li, Qibin

2017-10-01

The evolution mechanism of a vent pipe diameter on a waste-stabilization process in semi-aerobic bioreactor landfills was analyzed from the organic-matter concentration, biodegradability, spectral characteristics of dissolved organic matter, correlations and principal-component analysis. Waste samples were collected at different distances from the vent pipe and from different landfill layers in semi-aerobic bioreactor landfills with different vent pipe diameters. An increase in vent pipe diameter favored waste degradation. Waste degradation in landfills can be promoted slightly when the vent pipe diameter increases from 25 to 50 mm. It could be promoted significantly when the vent pipe diameter was increased to 75 mm. The vent pipe diameter is important in waste degradation in the middle layer of landfills. The dissolved organic matter in the waste is composed mainly of long-wave humus (humin), short-wave humus (fulvic acid) and tryptophan. The humification levels of the waste that was located at the center of vent pipes with 25-, 50- and 75-mm diameters were 2.2682, 4.0520 and 7.6419 Raman units, respectively. The appropriate vent pipe diameter for semi-aerobic bioreactor landfills with an 800-mm diameter was 75 mm. The effect of different vent pipe diameters on the degree of waste stabilization is reflected by two main components. Component 1 is related mainly to the content of fulvic acid, biologically degradable material and organic matter. Component 2 is related mainly to the content of tryptophan and humin from the higher vascular plants.

Evaluation of microtensile bond strength of different fissure sealants to bovine enamel.

Science.gov (United States)

Sen Tunc, E; Bayrak, S; Tuloglu, N; Ertas, E

2012-03-01

The aim of this study was to evaluate the microtensile bond strength (μTBS) of a new fissure sealant and compare it with conventional sealants which are applied to enamel alone, and also with self-etch and etch-and-rinse adhesives. Enamel specimens were prepared and randomly distributed into three groups according to fissure sealant (Aegis, Helioseal F, Helioseal Clear). Each group was then subdivided according to adhesive system (Clearfil S3, Single Bond, no adhesive). A universal testing machine was used to measure μTBS, and data were analysed using one-way ANOVA and Tukey's tests. μTBS values for all Aegis subgroups were significantly lower than for comparable Helioseal F and Helioseal Clear subgroups (p 0.05). In the Helioseal Clear group, μTBS values for Single Bond were significantly higher than for Clearfil S3 (p adhesive subgroups in the Aegis or Helioseal F groups (p > 0.05). Sealant μTBS values may be affected by material content. The addition of an adhesive may improve μTBS values of sealant to enamel. © 2012 Australian Dental Association.

[Banana peel: a possible source of infection in the treatment of nipple fissures].

Science.gov (United States)

Novak, Franz Reis; de Almeida, João Aprígio Guerra; de Souza e Silva, Rosana

2003-01-01

To study the microbiology of banana peel being sold in the city of Rio de Janeiro, in an attempt to determine the possibility that the peel may represent a source of infection for women who use it to treat nipple fissures. The following microorganisms were studied in 20 banana peel samples: mesophiles, total coliforms, fecal coliforms, Pseudomonas aeruginosa, lipolytic and proteolytic microorganisms, molds and yeasts, lactic bacteria, and coagulase-positive staphylococcus. The microbiological analyses revealed the occurrence of several typical groups of microorganisms, with the following distribution of positive results being detected in banana peel samples: mesophiles, 100%; total coliforms, 20%; coagulase-positive staphylococcus, 25%; molds and yeasts, 30%; proteolytic microorganisms, 70%; lipolytic microorganisms, 30%, and lactic bacteria, 95%. Fecal coliforms and Pseudomonas aeruginosa were not isolated. The results show the presence of potentially pathogenic microorganisms in levels which could compromise the microbiological quality of the banana peel. Its use for the treatment of nipple fissures can initiate an infectious process.

A Novel Approach to Model Earth Fissure Caused by Extensive Aquifer Exploitation and its Application to the Wuxi Case, China

Science.gov (United States)

Ye, Shujun; Franceschini, Andrea; Zhang, Yan; Janna, Carlo; Gong, Xulong; Yu, Jun; Teatini, Pietro

2018-03-01

Initially observed in the semiarid basins of southwestern USA, earth fissures due to aquifer over-exploitation are presently threatening a large number of subsiding basins in various countries worldwide. Different mechanics have been proposed to explain this process, such as differential compaction, horizontal movements, and fault reactivation. Numerical modeling and prediction of this major geohazard caused by overuse of groundwater resources are challenging because of two main requirements: shifting from the classical continuous to discontinuous geomechanics and incorporating two-dimensional features (the earth fissures) into large three-dimensional (3-D) modeling domain (the subsiding basin). In this work, we proposed a novel modeling approach to simulate earth fissure generation and propagation in 3-D complex geological settings. A nested two-scale approach associated with an original nonlinear elastoplastic finite element/interface element simulator allows modeling the mechanics of earth discontinuities, in terms of both sliding and opening. The model is applied on a case study in Wuxi, China, where groundwater pumping between 1985 and 2004 has caused land subsidence larger than 2 m. The model outcomes highlight that the presence of a shallow (˜80 m deep) bedrock ridge crossing the Yangtze River delta is the key factor triggering the earth fissure development in this area. Bending of the alluvial deposits around the ridge tip and shear stress due to the uneven piezometric change and asymmetrical shape of the bedrock have caused the earth fissure to onset at the land surface and propagate downward to a maximum depth of about 20-30 m. Maximum sliding and opening are computed in the range of 10-40 cm, in agreement with the order of magnitude estimated in the field.

Groundwater flow through fissured rock: field investigations and interpretation in the Albigna dam area, Graubuenden, Switzerland

International Nuclear Information System (INIS)

Kovari, K.; Arn, Th.; Gmuender, Ch.

1989-11-01

The rock foundation of a dam was chosen as the site for repeated observations of flow patterns in a fissured rock. Our project was carried out at the Albigna Dam in the Canton of Graubuenden, Switzerland, where the greatest fluctuation in the level of the lake was approximately 100 m. In the area of the dam the rock consists of a fresh, solid granite, whose fissure systems were well known as regards position and distribution. The measurement program for assessing the flow conditions consisted of two elements: piezometric pressure measurements in boreholes and strain measurements in boreholes. Pressure measurements were accomplished to define the potential field. Strain measurements were accomplished to detect fracture opening and closing as a function of the fluctuations in the lake level. From a combination of the two sets of observations it was hoped to be able to determine the interaction between hydraulics and mechanics, i.e. the coupling of two key processes with a possible influence on a changing permeability of the rock. Using the 'sliding micrometer', the continuous strain distribution was determined along two boreholes in the measuring plane. Pressures were measured using the 'Piezodex' system. Mathematical investigations were conducted with the AQUA-ROCK finite element program on a 2D-model. From just a visual comparison of the measured and calculated values it is clear that a different model achieves the best correlation depending on the level of the lake. For the maximum lake level, however, it is essential to take account of the action of the fissures either by way of the idealization according to Snow (main model 2) or by considering the individual fissures (main model 3). (author) figs., tabs., 12 refs

GPE-BWR and the containment venting and filtering issue

International Nuclear Information System (INIS)

Palomo, J.; Santiago, J. de

1988-01-01

The Spanish Boiling Water Reactor Owner's Group (GPE-BWR) is formed by three utilities, owning four units: Santa Maria de Garona (46 MWe, BWR3, Mark I containment), Cofrentes (975 MWe, BWR6, Mark III containment) and Valdecaballeros (2x975 MWe, BWR6, Mark III containment) - all of the reactors having been supplied by General Electric. One of the GPE-BWR's several committees is the Safety and Licensing Committee, which follows up the evolution of severe accident topics and particularly the containment venting and filtering issue. In September 1987, the Consejo de Seguridad Nuclear (CSN), the Spanish Regulatory Body, asked the GPE-BWR to define its position on the installation of a containment venting system. The GPE-BWR created a Working Group which presented a Report on Containment Venting to the CSN in January 1987 gathered from: the US Nuclear Regulatory Commission (NRC); some US utilities; and several European countries, especially France, Germany and Sweden. CSN's review of the containment venting Report and the Action Plan proposed by the GPE-BWR finished in April 1988. The conclusion of the Report and the proposed Action Plan take into account the US NRC's identified open items on severe accidents and the R and D programs scheduled to close these items

CFD analysis of gas explosions vented through relief pipes.

Science.gov (United States)

Ferrara, G; Di Benedetto, A; Salzano, E; Russo, G

2006-09-21

Vent devices for gas and dust explosions are often ducted to safe locations by means of relief pipes. However, the presence of the duct increases the severity of explosion if compared to simply vented vessels (i.e. compared to cases where no duct is present). Besides, the identification of the key phenomena controlling the violence of explosion has not yet been gained. Multidimensional models coupling, mass, momentum and energy conservation equations can be valuable tools for the analysis of such complex explosion phenomena. In this work, gas explosions vented through ducts have been modelled by a two-dimensional (2D) axi-symmetric computational fluid dynamic (CFD) model based on the unsteady Reynolds Averaged Navier Stokes (RANS) approach in which the laminar, flamelet and distributed combustion models have been implemented. Numerical test have been carried out by varying ignition position, duct diameter and length. Results have evidenced that the severity of ducted explosions is mainly driven by the vigorous secondary explosion occurring in the duct (burn-up) rather than by the duct flow resistance or acoustic enhancement. Moreover, it has been found out that the burn-up affects explosion severity due to the reduction of venting rate rather than to the burning rate enhancement through turbulization.

Analysis of containment venting at the Peach Bottom atomic power station

International Nuclear Information System (INIS)

Hanson, D.J.; Blackman, H.S.; Nelson, W.R.; Wright, R.E.; Leonard, M.T.; DiSalvo, R.

1988-01-01

An analysis of the extent to which containment venting would be effective in preventing or mitigating the consequences of severe accidents has been completed for the Peach Bottom Units 2 and 3 (BWR-4s with Mark I containments). The analysis indicates that the effectiveness of venting in preventing containment overpressurization highly depends on the sequence of the severe accident. Containment venting can be effective for several classes of sequences, including transients with failure of long-term decay heat removal and loss-of-coolant accidents with breaks inside the containment. However, based on draft procedures and equipment in place at the time of the evaluation, containment venting has limited potential for further reducing the risk associated with three severe accident sequences currently identified as important risk contributors at Peach Bottom. Means of improving the potential for risk reduction is identified, but their influence on risk is not analyzed. (orig./HP)

Analysis of containment venting at the Peach Bottom Atomic Power Station

International Nuclear Information System (INIS)

Hanson, D.J.; Blackman, H.S.; Nelson, W.R.; Wright, R.E.; Leonard, M.T.; DiSalvo, R.

1986-01-01

An analysis of the extent to which containment venting would be effective in preventing or mitigating the consequences of severe accidents has been completed for the Peach Bottom Atomic Power Station, Units 2 and 3 (BWR-4s with Mark I containments). The analysis indicates that the effectiveness of venting in preventing containment overpressurization highly depends on the sequence of the severe accident. Containment venting can be effective for several classes of sequences, including transients with failure of long-term decay heat removal and loss-of-coolant accidents with breaks inside the containment. However, based on draft procedures and equipment in place at the time of the evaluation, containment venting has limited potential for further reducing the risk associated with three severe accident sequences currently identified as important risk contributors at Peach Bottom. Means of improving the potential for risk reduction is identified, but their influence on risk is not analyzed

A finite element analysis of novel vented dental abutment geometries for cement-retained crown restorations.

Science.gov (United States)

Rodriguez, Lucas C; Saba, Juliana N; Meyer, Clark A; Chung, Kwok-Hung; Wadhwani, Chandur; Rodrigues, Danieli C

2016-11-01

Recent literature indicates that the long-term success of dental implants is, in part, attributed to how dental crowns are attached to their associated implants. The commonly utilized method for crown attachment - cementation, has been criticized because of recent links between residual cement and peri-implant disease. Residual cement extrusion from crown-abutment margins post-crown seating is a growing concern. This study aimed at (1) identifying key abutment features, which would improve dental cement flow characteristics, and (2) understanding how these features would impact the mechanical stability of the abutment under functional loads. Computational fluid dynamic modeling was used to evaluate cement flow in novel abutment geometries. These models were then evaluated using 3D-printed surrogate models. Finite element analysis also provided an understanding of how the mechanical stability of these abutments was altered after key features were incorporated into the geometry. The findings demonstrated that the key features involved in improved venting of the abutment during crown seating were (1) addition of vents, (2) diameter of the vents, (3) location of the vents, (4) addition of a plastic screw insert, and (5) thickness of the abutment wall. This study culminated in a novel design for a vented abutment consisting of 8 vents located radially around the abutment neck-margin plus a plastic insert to guide the cement during seating and provide retrievability to the abutment system.Venting of the dental abutment has been shown to decrease the risk of undetected residual dental cement post-cement-retained crown seating. This article will utilize a finite element analysis approach toward optimizing dental abutment designs for improved dental cement venting. Features investigated include (1) addition of vents, (2) diameter of vents, (3) location of vents, (4) addition of plastic screw insert, and (5) thickness of abutment wall.

A finite element analysis of novel vented dental abutment geometries for cement‐retained crown restorations

Science.gov (United States)

Rodriguez, Lucas C.; Saba, Juliana N.; Meyer, Clark A.; Chung, Kwok‐Hung; Wadhwani, Chandur

2016-01-01

Abstract Recent literature indicates that the long‐term success of dental implants is, in part, attributed to how dental crowns are attached to their associated implants. The commonly utilized method for crown attachment – cementation, has been criticized because of recent links between residual cement and peri‐implant disease. Residual cement extrusion from crown‐abutment margins post‐crown seating is a growing concern. This study aimed at (1) identifying key abutment features, which would improve dental cement flow characteristics, and (2) understanding how these features would impact the mechanical stability of the abutment under functional loads. Computational fluid dynamic modeling was used to evaluate cement flow in novel abutment geometries. These models were then evaluated using 3D‐printed surrogate models. Finite element analysis also provided an understanding of how the mechanical stability of these abutments was altered after key features were incorporated into the geometry. The findings demonstrated that the key features involved in improved venting of the abutment during crown seating were (1) addition of vents, (2) diameter of the vents, (3) location of the vents, (4) addition of a plastic screw insert, and (5) thickness of the abutment wall. This study culminated in a novel design for a vented abutment consisting of 8 vents located radially around the abutment neck‐margin plus a plastic insert to guide the cement during seating and provide retrievability to the abutment system.Venting of the dental abutment has been shown to decrease the risk of undetected residual dental cement post‐cement‐retained crown seating. This article will utilize a finite element analysis approach toward optimizing dental abutment designs for improved dental cement venting. Features investigated include (1) addition of vents, (2) diameter of vents, (3) location of vents, (4) addition of plastic screw insert, and (5) thickness of abutment wall. PMID

Detection of putatively thermophilic anaerobic methanotrophs in diffuse hydrothermal vent fluids.

Science.gov (United States)

Merkel, Alexander Y; Huber, Julie A; Chernyh, Nikolay A; Bonch-Osmolovskaya, Elizaveta A; Lebedinsky, Alexander V

2013-02-01

The anaerobic oxidation of methane (AOM) is carried out by a globally distributed group of uncultivated Euryarchaeota, the anaerobic methanotrophic arachaea (ANME). In this work, we used G+C analysis of 16S rRNA genes to identify a putatively thermophilic ANME group and applied newly designed primers to study its distribution in low-temperature diffuse vent fluids from deep-sea hydrothermal vents. We found that the G+C content of the 16S rRNA genes (P(GC)) is significantly higher in the ANME-1GBa group than in other ANME groups. Based on the positive correlation between the P(GC) and optimal growth temperatures (T(opt)) of archaea, we hypothesize that the ANME-1GBa group is adapted to thrive at high temperatures. We designed specific 16S rRNA gene-targeted primers for the ANME-1 cluster to detect all phylogenetic groups within this cluster, including the deeply branching ANME-1GBa group. The primers were successfully tested both in silico and in experiments with sediment samples where ANME-1 phylotypes had previously been detected. The primers were further used to screen for the ANME-1 microorganisms in diffuse vent fluid samples from deep-sea hydrothermal vents in the Pacific Ocean, and sequences belonging to the ANME-1 cluster were detected in four individual vents. Phylotypes belonging to the ANME-1GBa group dominated in clone libraries from three of these vents. Our findings provide evidence of existence of a putatively extremely thermophilic group of methanotrophic archaea that occur in geographically and geologically distinct marine hydrothermal habitats.

Chronic anal fissure: morphometric analysis of the anal canal at 3.0 Tesla MR imaging.

Science.gov (United States)

Erden, Ayşe; Peker, Elif; Gençtürk, Zeynep Bıyıklı

2017-02-01

OBJECTıVE: To compare the morphometric data relating to the muscular structures of the anal canal, in patients with chronic anal fissure and in control group, examined at a 3.0 Tesla MR system. Forty-seven consecutive patients with chronic anal fissure and randomly selected 40 patients who had no claims for perianal disease during their life time were included in the study. T2-weighted sagittal, high-resolution (HR) T2-weighted, and contrast-enhanced fat-suppressed T1-weighted oblique axial and oblique coronal images were retrospectively analyzed by two observers in consensus. Thickness of sphincteric muscles, anal canal length, anorectal angle, thickness of anococcygeal ligament, depth of Minor triangle, width between subcutaneous sphincters, vascularity of posterior commissure, visibility of posterosuperior projection of external sphincter, and angle between the distal anal canal and posterosuperior projection of external sphincter (H angle) in patients and in controls were compared and analyzed using t test, Mann-Whitney U test, and Spearman correlation. The patients with chronic anal fissure had longer anal canal (51.50 mm ± 0.91 vs. 44.11 mm ± 0.71; p = 0.000), thicker internal anal sphincter muscle at mid-anal level (4.18 ± 0.15 vs. 3.39 ± 0.07; p = 0.007), and wider space between subcutaneous external sphincters (11.39 ± 0.50 vs. 6.89 ± 0.22; p = 0.000). In patients, there was a positive correlation between H angle and external sphincter thickness at proximal (r = 0.347; p = 0.021), middle (r = 0427; p = 0.000), and distal (r = 0.518; p = 0.000)) levels of the anal canal. CONCLUSıON: 3.0 Tesla MR imaging provides detailed information about the morphometric changes in the anal sphincter muscles in patients with chronic anal fissure.

Kilauea's 5-9 March 2011 Kamoamoa fissure eruption and its relation to 30+ years of activity from Pu'u 'Ō'ō: Chapter 18

Science.gov (United States)

Orr, Tim R.; Poland, Michael P.; Patrick, Matthew R.; Thelen, Weston A.; Sutton, A.J.; Elias, Tamar; Thornber, Carl R.; Parcheta, Carolyn; Wooten, Kelly M.; Carey, Rebecca; Cayol, Valérie; Poland, Michael P.; Weis, Dominique

2015-01-01

Lava output from Kīlauea's long-lived East Rift Zone eruption, ongoing since 1983, began waning in 2010 and was coupled with uplift, increased seismicity, and rising lava levels at the volcano's summit and Pu‘u ‘Ō‘ō vent. These changes culminated in the four-day-long Kamoamoa fissure eruption on the East Rift Zone starting on 5 March 2011. About 2.7 × 106 m3 of lava erupted, accompanied by ˜15 cm of summit subsidence, draining of Kīlauea's summit lava lake, a 113 m drop of Pu‘u ‘Ō‘ō's crater floor, ˜3 m of East Rift Zone widening, and eruptive SO2 emissions averaging 8500 tonnes/day. Lava effusion resumed at Pu‘u ‘Ō‘ō shortly after the Kamoamoa eruption ended, marking the onset of a new period of East Rift Zone activity. Multiparameter monitoring before and during the Kamoamoa eruption suggests that it was driven by an imbalance between magma supplied to and erupted from Kīlauea's East Rift Zone and that eruptive output is affected by changes in the geometry of the rift zone plumbing system. These results imply that intrusions and eruptive changes during ongoing activity at Kīlauea may be anticipated from the geophysical, geological, and geochemical manifestations of magma supply and magma plumbing system geometry.

Investigations of a novel fauna from hydrothermal vents along the Arctic Mid-Ocean Ridge (AMOR) (Invited)

Science.gov (United States)

Rapp, H.; Schander, C.; Halanych, K. M.; Levin, L. A.; Sweetman, A.; Tverberg, J.; Hoem, S.; Steen, I.; Thorseth, I. H.; Pedersen, R.

2010-12-01

The Arctic deep ocean hosts a variety of habitats ranging from fairly uniform sedimentary abyssal plains to highly variable hard bottoms on mid ocean ridges, including biodiversity hotspots like seamounts and hydrothermal vents. Deep-sea hydrothermal vents are usually associated with a highly specialized fauna, and since their discovery in 1977 more than 400 species of animals have been described. This fauna includes various animal groups of which the most conspicuous and well known are annelids, mollusks and crustaceans. The newly discovered deep sea hydrothermal vents on the Mohns-Knipovich ridge north of Iceland harbour unique biodiversity. The Jan Mayen field consists of two main areas with high-temperature white smoker venting and wide areas with low-temperature seepage, located at 5-700 m, while the deeper Loki Castle vent field at 2400 m depth consists of a large area with high temperature black smokers surrounded by a sedimentary area with more diffuse low-temperature venting and barite chimneys. The Jan Mayen sites show low abundance of specialized hydrothermal vent fauna. Single groups have a few specialized representatives but groups otherwise common in hydrothermal vent areas are absent. Slightly more than 200 macrofaunal species have been identified from this vent area, comprising mainly an assortment of bathyal species known from the surrounding area. Analysis of stable isotope data also indicates that the majority of the species present are feeding on phytodetritus and/or phytoplankton. However, the deeper Loki Castle vent field contains a much more diverse vent endemic fauna with high abundances of specialized polychaetes, gastropods and amphipods. These specializations also include symbioses with a range of chemosynthetic microorganisms. Our data show that the fauna composition is a result of high degree of local specialization with some similarities to the fauna of cold seeps along the Norwegian margin and wood-falls in the abyssal Norwegian Sea

33 CFR 159.61 - Vents.

Science.gov (United States)

2010-07-01

... 33 Navigation and Navigable Waters 2 2010-07-01 2010-07-01 false Vents. 159.61 Section 159.61 Navigation and Navigable Waters COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) POLLUTION MARINE... to minimize clogging by either the contents of the tank or climatic conditions such as snow or ice. ...

Episode 49 of the Pu'u 'Ō'ō-Kūpaianaha eruption of Kilauea volcano-breakdown of a steady-state eruptive era

Science.gov (United States)

Mangan, M.T.; Heliker, C.C.; Mattox, T.N.; Kauahikaua, J.P.; Helz, R.T.

1995-01-01

The Pu'u 'O'o-Kupaianaha eruption (1983-present) is the longest lived rift eruption of either Kilauea or neighboring Mauna Loa in recorded history. The initial fissure opening in January 1983 was followed by three years of episodic fire fountaining at the Pu'u 'O'o vent on Kilauea's east rift zone ∼19km from the summit (episodes 4–47). These spectacular events gave way in July 1986 to five and a half years of near-continuous, low-level effusion from the Kupaianaha vent, ∼ 3km to the cast (episode 48). A 49th episode began in November 1991 with the opening of a new fissure between Pu'u 'O'o and Kupaianaha. This three week long outburst heralded an era of more erratic eruptive behavior characterized by the shut down of Kupaianaha in February 1992 and subsequent intermittent eruption from vents on the west flank of Pu'u 'O'o (episodes 50 and 51). The events occurring over this period are due to progressive shrinkage of the rift-zone reservoir beneath the eruption site, and had limited impact on eruption temperatures and lava composition.

Flows of Newtonian and Power-Law Fluids in Symmetrically Corrugated Cappilary Fissures and Tubes

Science.gov (United States)

Walicka, A.

2018-02-01

In this paper, an analytical method for deriving the relationships between the pressure drop and the volumetric flow rate in laminar flow regimes of Newtonian and power-law fluids through symmetrically corrugated capillary fissures and tubes is presented. This method, which is general with regard to fluid and capillary shape, can also be used as a foundation for different fluids, fissures and tubes. It can also be a good base for numerical integration when analytical expressions are hard to obtain due to mathematical complexities. Five converging-diverging or diverging-converging geometrics, viz. wedge and cone, parabolic, hyperbolic, hyperbolic cosine and cosine curve, are used as examples to illustrate the application of this method. For the wedge and cone geometry the present results for the power-law fluid were compared with the results obtained by another method; this comparison indicates a good compatibility between both the results.

Flows of Newtonian and Power-Law Fluids in Symmetrically Corrugated Cappilary Fissures and Tubes

Directory of Open Access Journals (Sweden)

Walicka A.

2018-02-01

Full Text Available In this paper, an analytical method for deriving the relationships between the pressure drop and the volumetric flow rate in laminar flow regimes of Newtonian and power-law fluids through symmetrically corrugated capillary fissures and tubes is presented. This method, which is general with regard to fluid and capillary shape, can also be used as a foundation for different fluids, fissures and tubes. It can also be a good base for numerical integration when analytical expressions are hard to obtain due to mathematical complexities. Five converging-diverging or diverging-converging geometrics, viz. wedge and cone, parabolic, hyperbolic, hyperbolic cosine and cosine curve, are used as examples to illustrate the application of this method. For the wedge and cone geometry the present results for the power-law fluid were compared with the results obtained by another method; this comparison indicates a good compatibility between both the results.

Central extracorporeal membrane oxygenation requiring pulmonary arterial venting after near-drowning.

Science.gov (United States)

Kimura, Mitsutoshi; Kinoshita, Osamu; Fujimoto, Yoshifumi; Murakami, Arata; Shindo, Takahiro; Kashiwa, Koichi; Ono, Minoru

2014-02-01

Extracorporeal membrane oxygenation (ECMO) is an effective respiratory and circulatory support in patients in refractory cardiogenic shock or cardiac arrest. Peripheral ECMO sometimes requires left heart drainage; however, few reports state that pulmonary arterial (PA) venting is required during ECMO support. We present a case of a 14-year-old boy who required PA venting during ECMO support after resuscitation from near-drowning in freshwater. A biventricular assist device with an oxygenator implantation was intended on day 1; however, we were unable to proceed because of increasing of pulmonary vascular resistance from the acute lung injury. Central ECMO with PA venting was then performed. On day 13, central ECMO was converted to biventricular assist device with an oxygenator, which was removed on day 16. This case suggests that PA venting during ECMO support may be necessary in some cases of respiratory and circulatory failure with high pulmonary vascular resistance after near-drowning.

Groundwater drainage from fissures as a source for lahars

Science.gov (United States)

Johnson, P. J.; Valentine, G. A.; Stauffer, P. H.; Lowry, C. S.; Sonder, I.; Pulgarín, B. A.; Santacoloma, C. C.; Agudelo, A.

2018-04-01

One mechanism for generating lahars at volcanoes experiencing unrest is the disruption of internal aquifers. These disruptions can trigger releases of large quantities of groundwater. An example of such aquifer disruption occurred at Nevado del Huila Volcano, Colombia, during February and April 2007 when large fractures formed across the summit area of the volcano and lahars were emitted from them. Previous work interpreted that lahar volumes could not be accounted for by melted glacial snow or precipitation, and by elimination suggested that the primary water source was groundwater. Conceptual models have been developed for perched, confined aquifers that have been heated and pressurized by magma intrusions, followed by sudden pressure release and water emission during fracture formation. We consider an alternative end member wherein water release from large fissures at volcanoes is driven by simple gravity drainage. We apply numerical modeling to quantify water discharge from the porous medium surrounding a fissure with a low-elevation free exit. If a long fracture with high vertical extent (on the order of hundreds of meters) intersects a highly connected saturated porous medium, large volumes (on order 103 m3/m of crack length) of water may be released within tens of minutes. The drainage rates from the model may be adequate to account for the Nevado del Huila events if the medium surrounding the crack contains a large volume of water and has high horizontal permeability. This simple but poorly understood mechanism can present a hazard on its own or compound other processes releasing water from volcanoes.

Vent clearing analysis of a Mark III pressure suppression containment

International Nuclear Information System (INIS)

Quintana, R.

1979-01-01

An analysis of the vent clearing transient in a Mark III pressure suppression containment after a hypothetical LOCA is carried out. A two-dimensional numerical model solving the transient fluid dynamic equations is used. The geometry of the pressure suppression pool is represented and the pressure and velocity fields in the pool are obtained from the moment the LOCA occurs until the first vent in the drywell wall clears. The results are compared to those obtained with the one-diemensional model used for containment design, with special interest on two-dimensional effects. Some conclusions concerning the effect of the water discharged into the suppression pool through the vents on submerged structures are obtained. Future improvements to the model are suggested. (orig.)

Discovery and Distribution of Black Smokers on the Western Galapagos Spreading Center: Implications for Spatial and Temporal Controls on High Temperature Venting at Ridge/Hotspot Intersections

Science.gov (United States)

Haymon, R. M.; Anderson, P. G.; Baker, E. T.; Resing, J. A.; White, S. M.; MacDonald, K. C.

2006-12-01

Though nearly one-fifth of the mid-ocean ridge (MOR) lies on or near hotspots, it has been debated whether hotspots increase or decrease MOR hydrothermal flux, or affect vent biota. Despite hotspot enhancement of melt supply, high-temperature vent plumes are enigmatically sparse along two previously-surveyed ridge- hotspot intersections [Reykjanes Ridge (RR), Southeast Indian Ridge (SEIR)]. This has been attributed to crustal thickening by excess volcanism. During the 2005-06 GalAPAGoS expedition, we conducted nested sonar, plume, and camera surveys along a 540 km-long portion of the Galapagos Spreading Center (GSC) where the ridge intersects the Galapagos hotspot at lon. 94.5 -89.5 deg. W. Although MOR hydrothermal springs were first found along the eastern GSC crest in 1977 near lon. 86 deg. W, the GalAPAGoS smokers are the first active high-temperature vents to be found anywhere along the Cocos-Nazca plate boundary. Active and/or recently-inactive smokers were located beneath plumes at 5 sites on the seafloor between lon. 91 deg. W and 94.5 deg. W (see Anderson et al., this session) during near-bottom, real-time fiber-optic Medea camera surveys. Smokers occur along eruptive seafloor fissures atop axial volcanic ridges near the middles of ridge segments, mainly in areas underlain by relatively shallow, continuous axial magma chamber (AMC) seismic reflectors. These findings (1) support magmatic, rather than tectonic, control of GSC smoker distribution; (2) demonstrate that thick crust at MOR-hotspot intersections does not prevent high-temperature hydrothermal vents from forming; and, (3) appear to be inconsistent with models suggesting that enhanced hydrothermal cooling causes abrupt deepening of the AMC and transition from non-rifted to rifted GSC morphology near lon. 92.7 deg. W. The widely-spaced smoker sites located on different GSC segments exhibit remarkably similar characteristics and seafloor settings. Most sites are mature or extinct, and are on lava

Assessment of Literature Related to Combustion Appliance Venting Systems

Energy Technology Data Exchange (ETDEWEB)

Rapp, Vi H. [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Singer, Brett C. [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Stratton, Chris [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Wray, Craig P. [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States)

2012-06-01

In many residential building retrofit programs, air tightening to increase energy efficiency is constrained by concerns about related impacts on the safety of naturally vented combustion appliances. Tighter housing units more readily depressurize when exhaust equipment is operated, making combustion appliances more prone to backdraft or spillage. Several test methods purportedly assess the potential for depressurization-induced backdrafting and spillage, but these tests are not robustly reliable and repeatable predictors of venting performance, in part because they do not fully capture weather effects on venting performance. The purpose of this literature review is to investigate combustion safety diagnostics in existing codes, standards, and guidelines related to combustion appliances. This review summarizes existing combustion safety test methods, evaluations of these test methods, and also discusses research related to wind effects and the simulation of vent system performance. Current codes and standards related to combustion appliance installation provide little information on assessing backdrafting or spillage potential. A substantial amount of research has been conducted to assess combustion appliance backdrafting and spillage test methods, but primarily focuses on comparing short-term (stress) induced tests and monitoring results. Monitoring, typically performed over one week, indicated that combinations of environmental and house operation characteristics most conducive to combustion spillage were rare. Research, to an extent, has assessed existing combustion safety diagnostics for house depressurization, but the objectives of the diagnostics, both stress and monitoring, are not clearly defined. More research is also needed to quantify the frequency of test “failure” occurrence throughout the building stock and assess the statistical effects of weather (especially wind) on house depressurization and in turn on combustion appliance venting

Dynamics of leaching a uniformly fissured ore body

International Nuclear Information System (INIS)

Ignatov, A.A.; Proskurin, S.A.

1987-01-01

Mathematical simulation was used to study the dynamics of mass transfer during the percolation of a reagent solution through a packing of coarse ore particles. The uniformly fissured ore body was represented by a cubic packing of spherical particles of constant radius, formed from a chemically inert silicate cement with a uniformly distributed soluble mineral component. The rate of percolation of the reagent through the packing was constant. The proposed model can be used to find the conditions for underground hydrodynamic leaching. The rate of non-catalytic solid-liquid reaction was deduced on the basis of both the kinetics of dissolution of the mineral component of the ore and the rate of diffusion of the dissolved substance

40 CFR 63.115 - Process vent provisions-methods and procedures for process vent group determination.

Science.gov (United States)

2010-07-01

... this section. (2) The gas volumetric flow rate shall be determined using Method 2, 2A, 2C, or 2D of 40... accepted chemical engineering principles, measurable process parameters, or physical or chemical laws or...)(3) of this section. (i) The vent stream volumetric flow rate (Qs), in standard cubic meters per...

Analysis of design and operational effects of filtered containment venting on depressurization and fission product release

Energy Technology Data Exchange (ETDEWEB)

Park, Jong Woon; Seol, Wook-Cheol; Kim, Jisu [Dongguk Univ., Gyeongbuk (Korea, Republic of)

2017-03-15

Effects of design and operational parameters of filtered containment venting system during a specified containment depressurization and relative aero sol release amount are analyzed. The analyses is performed by using the MAAP4 code for the APR1400 reactor. Major results uniquely identified from the analyses can be noted as following: Even though containment depressurization is accelerated as the pipe size increases, the venting system solution is also depleted earlier. Elapsed times to reach lower end pressure of 2 bar are nearly identical regardless of the vent initiation pressure and thus early venting is not much beneficial than late venting. Stroke time of the isolation valves has no effect on the depressurization performance and thus slow opening is beneficial for load reduction from the vent effluent.

A model for vented deflagration of hydrogen in a volume

International Nuclear Information System (INIS)

Mulpuru, S.R.; Wilkin, G.B.

1982-02-01

A simple model was constructed to predict the property transients resulting from the deflagration of a combustible mixture in a sphere or cylinder with venting of the gas mixture to the environment. A computer program VENT, was written to solve the model equation. The model will be particularly useful for studying hydrogen burning effects in loss-of-coolant plus losss of emergency coolant accidents in CANDU reactors

Optimal Dosing of Botulinum Toxin for Treatment of Chronic Anal Fissure: A Systematic Review and Meta-Analysis.

Science.gov (United States)

Lin, Jin Xin; Krishna, Sanjeev; Su'a, Bruce; Hill, Andrew G

2016-09-01

Chronic anal fissures are associated with significant morbidity and reduced quality of life. Studies have investigated the efficacy of botulinum toxin with variable results; thus, there is currently no consensus on botulinum toxin dose or injection sites. This study aimed to systematically analyze trials studying the efficacy of botulinum toxin for treatment of chronic anal fissure to identify an optimum dosage and injection regimen. A comprehensive review of the literature was conducted according to PRISMA guidelines. PubMed/Medline, Embase, Scopus, and the Cochrane Library were searched from inception to June 2015. All clinical trials that investigated the efficacy of botulinum toxin for chronic anal fissure were selected according to specific criteria. The interventions used were various doses of botulinum toxin. Clinical outcomes, dosage, and injection site data were evaluated with weighted pooled results for each dosage and 95% confidence intervals. There were 1158 patients, with 661 in botulinum toxin treatment arms, from 18 clinical trials included in this review. The outcomes of interest were 3-month healing, incontinence, and recurrence rates. Meta-regression analysis demonstrated a small decrease in healing rate (0.34%; 95% CI, 0-0.68; p = 0.048) with each increase in dosage, a small increase in incontinence rate (1.02 times; 95% CI, 1.0002-1.049; p = 0.048) with each increase in dosage and a small increase in recurrence rate (1.037 times; 95% CI, 1.018-1.057; p = 0.0002) with each increase in dosage. The optimum injection site could not be determined. This study was limited by weaknesses in the underlying evidence, such as variable quality, short follow-up, and a limited range of doses represented. Fissure healing with lower doses of botulinum toxin is as effective as with high doses. Lower doses also reduce the risk of incontinence and recurrence in the long term.

Modelling Venting and Pressure Build-up in a 18650 LCO Cell during Thermal Runaway (ABSTRACT)

DEFF Research Database (Denmark)

Coman, Paul Tiberiu; Veje, Christian; White, Ralph

Li-ion batteries are a very popular type of electric storage devices that possess high energy density when compared to the other battery chemistries. Due to this property, when operating under abusive conditions such as high ambient temperature, the batteries can experience thermal runaway, which...... may lead to fires and explosions. To prevent this, it is therefore important to model thermal runaway considering different events such as venting and the pressure development inside the battery cell, which makes the main purpose of this paper. A model consisting of the different decomposition....... By fitting the activation energies, and measuring experimentally the mass of the ejecta during thermal runaway, the model is compared and validated against an extensive experiment performed by Golukbov et al. [1] during oven heating. When analysing the results, it is found that by including the venting...

Analysis of the implementation of a sand bed type filter for the venting of a nuclear power plant; Analisis de la implementacion de un filtro tipo lecho de arena para el venteo de una central nuclear

Energy Technology Data Exchange (ETDEWEB)

Cuevas V, D.; Sainz M, E.; Ortiz V, J., E-mail: delfy.cu@gmail.com [ININ, Carretera Mexico-Toluca s/n, 52750 Ocoyoacac, Estado de Mexico (Mexico)

2017-09-15

The filtered venting of the containment has been adopted in European countries to mitigate the consequences derived from the excess pressure of the containment during a severe accident. When venting has taken place, the fission products are released directly into the environment, unless a filter is placed in the path of the same, so various types of filters are used to trap the fission products. The containment venting filters currently installed use different filtering technologies that involve more than one medium. Those who use water as the first stage of filtration are called wet systems, are equipped with additional stages to eliminate water drops and emissions of fine aerosols, and may even be equipped with an element that contains certain means of absorption for the gaseous iodine species filtration. Other designs, based on deep bed filtration as the main retention stage, called dry filters; use metal fiber, ceramic or sand filtration media to trap aerosols. The present work evaluates the hydraulic characteristics of the sand bed type filter designed by EDF as a candidate to be installed in the containment of the BWR Mark II (primary containment type of the Laguna Verde nuclear power plant). The evaluation of the sand bed filter was performed using the OpenFOAM open source software package. Models of each zone of the filtering device were generated and by means of a series of parametric calculations of computational fluid mechanics, the relevant hydrodynamic characteristics of the device were obtained, such as pressure drops against mass flow and pressure fields and velocity under different operating conditions. On the other hand, the validation of the sand bed filter model was made when comparing the results of experimental tests carried out in a sand column of the PITEAS program (1985-1986) against the simulation in OpenFOAM. The results obtained are very close to those obtained experimentally. (Author)

Vented nuclear fuel element

International Nuclear Information System (INIS)

Oguma, M.; Hirose, Y.

1976-01-01

A description is given of a vented nuclear fuel element having a plenum for accumulation of fission product gases and plug means for delaying the release of the fission product gases from the plenum, the plug means comprising a first porous body wettable with a liquid metal and a second porous body non-wettable with the liquid metal, the first porous body being impregnated with the liquid metal and in contact with the liquid metal

Direct torus venting analysis for Chinshan BWR-4 plant with MARK-I containment

Energy Technology Data Exchange (ETDEWEB)

Yuann, Yng-Ruey, E-mail: ryyuann@iner.gov.tw

2017-03-15

Highlights: • Study the effectiveness of Direct Torus Venting System (DTVS) during extended SBO of 24 h for Chinshan MARK-I plant. • Containment response is analyzed by GOTHIC based on boundary conditions from RETRAN calculation. • Analyses are performed with and without DTVS, respectively. • Suppression pool is sub-divided and thermal stratification is observed. - Abstract: The Chinshan plant, owned by Taiwan Power Company, has twin units of BWR-4 reactor and MARK-I containment. Both units have been operating at rated core thermal power of 1840 MWt. The existing Direct Torus Venting System (DTVS) is the main system used for venting the containment during the extended station blackout event. The purpose of this paper is to study the effects of the DTVS venting on the response of the containment pressure and temperature. The reactor is depressurized by manually opening the safety relief valves (SRVs) during the SBO, which causes the mass and energy to be discharged into and heat up the suppression pool. The RETRAN model is used to calculate the Nuclear Steam Supply System (NSSS) response and generate the SRV blowdown conditions, including SRV pressure, enthalpy, and mass flow rate. These conditions are then used as the time-dependent boundary conditions for the GOTHIC code to calculate the containment pressure and temperature response. The DTVS model is established in the GOTHIC model based on the venting size, venting piping loss, venting initiation time, and venting source. The lumped volume model, 1-D coarse-mesh model, and 3-D coarse-mesh model are considered in the torus volume. The calculation is first done without DTVS venting to establish a reference basis. Then a case with DTVS available is performed. Comparison of the two cases shows that the existing DTVS design is effective in mitigating the severity of the containment pressure and temperature transients. The results also show that the 1-D coarse-mesh model may not be appropriate since a

CFD application on IRWST hydrodynamic analysis during the sparger air venting

International Nuclear Information System (INIS)

Kim, Y. I.; Hwang, Y. D.; Kim, H. Y.; Bae, Y. Y.; Park, J. K.

1998-01-01

A numerical study was performed using preleased FLUENT V4.5 to investigate the applicability of the CFD model for IRWST hydrodynamic analysis during the sparger air venting. Transient calculations were performed with the compressible VOF model on the selected ABB-Atom Unit Cell Test data. This study was mainly focused on the simulation of the bubble formation process in the water pool and time varying pressure history during the air venting from the sparger. The simulated peak pressure was over-predicted in general, but the main frequency is in good agreement with the simulated data. It was shown that there was a strong dependence on the mass discharge rate of the air trapped in the vent line. The peak pressure acceptable for the conservative evaluation of the sparger performance was obtained by reducing the air discharge velocity. This indicates that the proper estimations of the air venting velocity consistent with the sparger design and operating conditions is essential for the application of FLUENT V4.5 to the sparger performance analysis of KNGR

Arsenic speciation in shrimp and mussel from the Mid-Atlantic hydrothermal vents

DEFF Research Database (Denmark)

Larsen, Erik Huusfeldt; Quetel, C. R.; Munoz, R.

1997-01-01

Specimens of shrimp (Rimicaris exoculata) and mussel (Bathymodiolus puteoserpentis) were collected 3500 m below the ocean surface at the hydrothermal vents of the mid-Atlantic Ridge (TAG and Snake Pit sites, respectively). Arsenic, a potentially toxic element, is among the substances emitted...... by the hydrothermal vents. The hydrothermal vent shrimp, which are known to be a primary consumer of the primary producing chemolithoautotrophic bacteria, contained arsenic at 13 mu g g(-1) almost exclusively as arsenobetaine (AsB). Arsenic was present in the soft:issues of the mussel at 40 mu g g(-1) and the major...... of arsenic species found in the shrimp and mussel species in the deep-sea is similar to that found in their counterparts from the ocean surface. It is concluded that the autotrophic bacteria of the hydrothermal vent ecosystem and the symbiotic bacteria harboured in the mussel species are responsible...

Westinghouse containment filtered venting system wet scrubber technology

International Nuclear Information System (INIS)

Kristensson, S.; Nilsson, P-O.

2014-01-01

Following the Fukushima event Westinghouse has further developed and enhanced its filtered containment venting system (FCVS) product line. The filtration efficiency of the proven FILTRA-MVSS system installed at all Swedish NPPs as well as at the Muhelberg plant in Switzerland has been enhanced and a new wet scrubber design, SVEN (Safety Venting), based on the FILTRA-MVSS tradition, developed. To meet increased filtration requirements for organic iodine these two wet scrubber products have been complemented with a zeolite module. The offering of a select choice of products allows for a better adjustment to the specific constraints and needs of each nuclear power station that is planning for the installation of such a system. The FILTRA-MVSS (MVSS=Multi Venturi Scrubber System) is a wet containment filtered vent system that uses multiple venturies to create an interaction between the vent gases and the scrubber media allowing for removal of aerosols and gaseous iodines in a very efficient manner. The FILTRA-MVSS was originally developed to meet stringent requirements on autonomy and maintained filtration efficiency over a wide range of venting conditions. The system was jointly developed in the late 80's by ABB Atom and ABB Flaekt, today Westinghouse and Alstom. Following installations in Sweden and Switzerland the system was further developed by replacement of the gravel-bed moisture separator with a standard demister and by addition of a set of sintered metal fibre filter cartridges placed after the moisture separator step. The system is today offered as a modular steel tank design to simplify installation at site. To reduce complexity and delivery time Westinghouse has developed an alternative design in which the venturi module is replaced by a submerged metal fibre filter cartridges module. This new wet scrubber design, SVEN (patent pending), provides a flexible, compact, and lower weight system, while still preserving and even enhancing the filtration

Modeling of zero gravity venting: Studies of two-phase heat transfer under reduced gravity

Science.gov (United States)

Merte, H., Jr.

1986-01-01

The objective is to predict the pressure response of a saturated liquid-vapor system when undergoing a venting or depressurization process in zero gravity at low vent rates. An experimental investigation of the venting of cylindrical containers partially filled with initially saturated liquids was previously conducted under zero-gravity conditions and compared with an analytical model which incorporated the effect of interfacial mass transfer on the ullage pressure response during venting. A new model is presented to improve the estimation of the interfacial mass transfer. Duhammel's superposition integral is incorporated to approximate the transient temperature response of the interface, treating the liquid as a semi-infinite solid with conduction heat transfer. Account is also taken of the condensation taking place within the bulk of a saturated vapor as isentropic expansion takes place. Computational results are presented for the venting of R-11 from a given vessel and initial state for five different venting rates over a period of three seconds, and compared to prior NASA experiments. An improvement in the prediction of the final pressure takes place, but is still considerably below the measurements.

Fissure sealant materials: Wear resistance of flowable composite resins.

Science.gov (United States)

Asefi, Sohrab; Eskandarion, Solmaz; Hamidiaval, Shadi

2016-01-01

Background. Wear resistance of pit and fissure sealant materials can influence their retention. Wear characteristics of sealant materials may determine scheduling of check-up visits. The aim of this study was to compare wear resistance of two flowable composite resins with that of posterior composite resin materials. Methods. Thirty-five disk-shaped specimens were prepared in 5 groups, including two flowable composite resins (Estelite Flow Quick and Estelite Flow Quick High Flow), Filtek P90 and Filtek P60 and Tetric N-Ceram. The disk-shaped samples were prepared in 25-mm diameter by packing them into a two-piece aluminum mold and then light-cured. All the specimens were polished for 1minute using 600-grit sand paper. The samples were stored in distilled water at room temperature for 1 week and then worn by two-body abrasion test using "pin-on-disk" method (with distilled water under a 15-Nload at 0.05 m/s, for a distance of 100 meter with Steatite ceramic balls antagonists). A Profilometer was used for evaluating the surface wear. Data were analyzed with the one-way ANOVA. Results. Estelite Flow Quick exhibited 2708.9 ± 578.1 μm(2) and Estelite Flow Quick High Flow exhibited 3206 ± 2445.1 μm(2)of wear but there were no significant differences between the groups. They demonstrated similar wear properties. Conclusion. Estelite flowable composite resins have wear resistance similar to nano- and micro-filled and micro-hybrid composite resins. Therefore, they can be recommended as pit and fissure sealant materials in the posterior region with appropriate mechanical characteristics.

Geophysical and geochemical methods applied to investigate fissure-related hydrothermal systems on the summit area of Mt. Etna volcano (Italy)

Science.gov (United States)

Maucourant, Samuel; Giammanco, Salvatore; Greco, Filippo; Dorizon, Sophie; Del Negro, Ciro

2014-06-01

A multidisciplinary approach integrating self-potential, soil temperature, heat flux, CO2 efflux and gravity gradiometry signals was used to investigate a relatively small fissure-related hydrothermal system near the summit of Mt. Etna volcano (Italy). Measurements were performed through two different surveys carried out at the beginning and at the end of July 2009, right after the end of the long-lived 2008-2009 flank eruption and in coincidence with an increase in diffuse flank degassing related to a reactivation of the volcano, leading to the opening of a new summit vent (NSEC). The main goal was to use a multidisciplinary approach to the detection of hidden fractures in an area of evident near-surface hydrothermal activity. Despite the different methodologies used and the different geometry of the sampling grid between the surveys, all parameters concurred in confirming that the study area is crossed by faults related with the main fracture systems of the south flank of the volcano, where a continuous hydrothermal circulation is established. Results also highlighted that hydrothermal activity in this area changed both in space and in time. These changes were a clear response to variations in the magmatic system, notably to migration of magma at various depth within the main feeder system of the volcano. The results suggest that this specific area, initially chosen as the optimal test-site for the proposed approach, can be useful in order to get information on the potential reactivation of the summit craters of Mt. Etna.

The discovery of new deep-sea hydrothermal vent communities in the southern ocean and implications for biogeography.

Directory of Open Access Journals (Sweden)

Alex D Rogers

2012-01-01

Full Text Available Since the first discovery of deep-sea hydrothermal vents along the Galápagos Rift in 1977, numerous vent sites and endemic faunal assemblages have been found along mid-ocean ridges and back-arc basins at low to mid latitudes. These discoveries have suggested the existence of separate biogeographic provinces in the Atlantic and the North West Pacific, the existence of a province including the South West Pacific and Indian Ocean, and a separation of the North East Pacific, North East Pacific Rise, and South East Pacific Rise. The Southern Ocean is known to be a region of high deep-sea species diversity and centre of origin for the global deep-sea fauna. It has also been proposed as a gateway connecting hydrothermal vents in different oceans but is little explored because of extreme conditions. Since 2009 we have explored two segments of the East Scotia Ridge (ESR in the Southern Ocean using a remotely operated vehicle. In each segment we located deep-sea hydrothermal vents hosting high-temperature black smokers up to 382.8°C and diffuse venting. The chemosynthetic ecosystems hosted by these vents are dominated by a new yeti crab (Kiwa n. sp., stalked barnacles, limpets, peltospiroid gastropods, anemones, and a predatory sea star. Taxa abundant in vent ecosystems in other oceans, including polychaete worms (Siboglinidae, bathymodiolid mussels, and alvinocaridid shrimps, are absent from the ESR vents. These groups, except the Siboglinidae, possess planktotrophic larvae, rare in Antarctic marine invertebrates, suggesting that the environmental conditions of the Southern Ocean may act as a dispersal filter for vent taxa. Evidence from the distinctive fauna, the unique community structure, and multivariate analyses suggest that the Antarctic vent ecosystems represent a new vent biogeographic province. However, multivariate analyses of species present at the ESR and at other deep-sea hydrothermal vents globally indicate that vent biogeography is more

Variations in deep-sea hydrothermal vent communities on the Mid-Atlantic Ridge near the Azores plateau

Science.gov (United States)

Desbruyères, D.; Biscoito, M.; Caprais, J.-C.; Colaço, A.; Comtet, T.; Crassous, P.; Fouquet, Y.; Khripounoff, A.; Le Bris, N.; Olu, K.; Riso, R.; Sarradin, P.-M.; Segonzac, M.; Vangriesheim, A.

2001-05-01

Near the Azores Triple Junction as the Azores Plateau is approached, the ridge axis becomes shallower; its depth decreases from ca. 2400 m in the R AINBOW vent field (36°13'N) to ca. 850 m in the M ENEZ G WEN vent field (37°35'N). In this area, extensive mussel beds of the mytilid Bathymodiolus azoricus dominate the hydrothermal vent fauna, along with populations of three shrimps ( Rimicaris exoculata, Mirocaris fortunata and Chorocaris chacei). The main physical and chemical characteristics of the vent habitat were studied by discrete sampling, in situ analysis and sediment trap moorings. The vent fauna is distributed along a variable band where the vent fluids and seawater mix, with R. exoculata living in the most concentrated areas and Bathymodiolus azoricus in the most diluted zones. Various non-endemic species live at the border of the vent field. The variations observed in structure and composition of the communities along the depth gradient are most likely due to changes in vent fluid toxicity (metallic and sulphide content) and suspended mineral particles, which render the fluids harsher for species living there. The main faunal differences observed between L UCKY S TRIKE and M ENEZ G WEN hydrothermal fields are due to an impoverishment in the hydrothermal endemic species and to the penetration of bathyal species. The comparison of the three studied vent fields suggests the existence of a succession of several biogeographic islands rather than a single province.

Analysis of Gas Vent System in Overseas LILW Disposal Facilities

Energy Technology Data Exchange (ETDEWEB)

Kim, Ju Yub; Kim, Ju Youl [FNC Technology Co., Yongin (Korea, Republic of); Jung, Hae Ryong; Ha, Jae Chul [Korea Radioactive Waste Management Corporation, Daejeon (Korea, Republic of)

2012-05-15

A Low- and Intermediate-Level Radioactive Waste (LILW) disposal facility is currently under construction in Korea. It is located in the aquifer, 80{approx}130 m below the ground surface. Thus, it is expected that disposal facility will be saturated after closure and various gases will be generated from metal corrosion, microbial degradation of organic materials and radiolysis. Generated gases will move up to the upper part of the silo, and it will increase the pressure of the silo. Since the integrity of the engineered barrier could be damaged, development of effective gas vent system which can prevent the gas accumulation in the silo is essential. In order to obtain basic data needed to develop site-specific gas vent system, gas vent systems of Sweden, Finland and Switzerland, which have the disposal concept of underground facility, were analyzed

Spontaneous Cerebrospinal Fluid Otorrhea from a Persistent Tympanomeningeal Fissure Presenting as Recurrent Serous Otitis Media

DEFF Research Database (Denmark)

Zakaryan, Arman; Poulsgaard, Lars; Hollander, Camilla

2015-01-01

We describe spontaneous cerebrospinal fluid (CSF) otorrhea through a patent tympanomeningeal (Hyrtl) fissure presenting as recurrent serous otitis media. The CSF leak was observed when a drain was placed through the tympanic membrane by an otologist. The diagnosis was then confirmed by computed...

Genetic diversity of archaea in deep-sea hydrothermal vent environments.

OpenAIRE

Takai, K; Horikoshi, K

1999-01-01

Molecular phylogenetic analysis of naturally occurring archaeal communities in deep-sea hydrothermal vent environments was carried out by PCR-mediated small subunit rRNA gene (SSU rDNA) sequencing. As determined through partial sequencing of rDNA clones amplified with archaea-specific primers, the archaeal populations in deep-sea hydrothermal vent environments showed a great genetic diversity, and most members of these populations appeared to be uncultivated and unidentified organisms. In the...

Venting processes: Effects on the vicinity

International Nuclear Information System (INIS)

Hattwig, M.

1980-01-01

In the case of venting as a protective measure against explosions a dangerous pressure wave and a large flame must be expected in the neighbourhood of the vent. Moreover the recoil force which is exerted on the protected vessel can be the cause for the destruction of the plant. Therefore experiments have been made on the dependence of the pressure wave and the recoil force from well-known or easily determinable parameters. The results of the investigations allow the estimation of the maximum overpressure which must be expected at a given point outside the vessel, if the reduced explosion pressure which will be reached in the interior of the vessel is known. Beyond that it could be shown that the maximum recoil force is nearly always considerably smaller than the value given by theory. Only very rarely the theoretical value is reached. Therefore it is totally sufficient for practical purposes when the maximum recoil to be expected is calculated from the theoretical equation. (orig.) [de

MAVEN Contamination Venting and Outgassing Analysis

Science.gov (United States)

Petro, Elaine M.; Hughes, David W.; Secunda, Mark S.; Chen, Philip T.; Morrissey, James R.; Riegle, Catherine A.

2014-01-01

Mars Atmosphere and Volatile EvolutioN (MAVEN) is the first mission to focus its study on the Mars upper atmosphere. MAVEN will study the evolution of the Mars atmosphere and climate, by examining the conduit through which the atmosphere has to pass as it is lost to the upper atmosphere. An analysis was performed for the MAVEN mission to address two distinct concerns. The first goal of the analysis was to perform an outgassing study to determine where species outgassed from spacecraft materials would redistribute to and how much of the released material might accumulate on sensitive surfaces. The second portion of the analysis serves to predict what effect, if any, Mars atmospheric gases trapped within the spacecraft could have on instrument measurements when re-released through vents. The re-release of atmospheric gases is of interest to this mission because vented gases from a higher pressure spacecraft interior could bias instrument measurements of the Mars atmosphere depending on the flow rates and directions.

Analyse du vent sur l'aérodrome de Brasov-Ghimbav (Roumanie

Directory of Open Access Journals (Sweden)

Marian Ilie Briceag

2011-01-01

Full Text Available Cette analyse du vent est destinée à préciser les conditions météorologiques locales qui conditionnent le fonctionnement de l'aérodrome de Brasov-Ghimbav. En aviation, la direction et l'intensité du vent sont très importantes pour le décollage et plus encore pour l'atterrissage des aéronefs. L'étude de cet élément météorologique est réalisée à partir d'une analyse climatologique portant sur 39 années, de 1971 à 2009, et d'une analyse aérologique sur 10 années, de 2000 à 2009 (les observations météorologiques ont été fournies par l'Administration Nationale de la Météorologie. Les résultats obtenus montrent la distribution prédominante du vent selon certaines directions, les directions nord-ouest et sud-ouest, pour les observations visuelles anciennes, et les directions ouest-nord-ouest et sud-sud-ouest, pour les observations automatiques au cours des six dernières années. Quelle que soit la méthode d'observation, c'est le vent de travers (directions ouest qui atteint les vitesses les plus élevées sur la piste principale de l'aérodrome de Brasov-Ghimbav, comme du reste sur la piste projetée pour le futur aéroport international de Brasov. Cela constitue un problème pour les aéronefs les plus légers, dont les valeurs limites pour le vent de travers sont faibles. Dans ce contexte, la prévision des vents violents est très importante. La distribution horaire des vents sur la période 2000­2009, montre notamment qu'au printemps et en été, les vents de nord-ouest sont largement dominants durant le jour, en particulier pour les vitesses [10-15 m/s, avec une fréquence maximale entre 10 et 15 heures. L'analyse aérologique des situations météorologiques apporte des éléments d'explication à certaines observations. Ainsi les vitesses du vent ≥ 20 m/s ont été enregistrées majoritairement en présence du cyclone Islandais, lors du passage du front atmosphérique froid, le contraste barrique étant �

CFD Simulation of rigid venting of the containment of a BWR-5 Mark-II reactor

International Nuclear Information System (INIS)

Galindo G, I. F.; Vazquez B, A. K.; Velazquez E, L.; Tijerina S, F.; Tapia M, R.

2016-09-01

In conditions of prolonged loss of external energy or a severe accident, venting to the atmosphere is an alternative to prevent overpressure and release of fission products from the primary containment of a nuclear reactor. Due to the importance of flow determination through rigid vents, a computational fluid dynamics (CFD) model is proposed to verify the capacity of rigid vents in the primary containment of a boiling water reactor (BWR) under different operating conditions (pressure, temperature and compositions of the fluids). The model predicts and provides detailed information on variables such as mass flow and velocity of the venting gases. In the proposed model the primary containment gas is vented to the atmosphere via rigid vents (pipes) from the dry and wet pit. Is assumed that the container is pressurized because is in a defined scenario, and at one point the venting is open and the gas released into the atmosphere. The objective is to characterize the flow and validate the CFD model for the overpressure conditions that occur in an accident such as a LOCA, Sbo, etc. The model is implemented with Ansys-Fluent general-purpose CFD software based on the geometry of the venting ducts of the containment of a BWR. The model is developed three-dimensional and resolves at steady state for compressible flow and includes the effects of the turbulence represented by the Reynolds stress model. The CFD results are compared with the values of a one-dimensional and isentropic model for compressible flow. The relative similarity of results leads to the conclusion that the proposed CFD model can help to predict the rigid venting capacity of the containment of a BWR, however more information is required for full validation of the proposed model. (Author)

Botulinum toxin A injection for chronic anal fissures and anal sphincter spasm improves quality of life in recessive dystrophic epidermolysis bullosa

Directory of Open Access Journals (Sweden)

Cassandra Chaptini, MBBS

2015-12-01

Full Text Available We report a 20-year-old female with generalized, severe, recessive dystrophic epidermolysis bullosa who developed secondary chronic anal fissures. This resulted in anal sphincter spasm and severe, disabling pain. She was treated with five botulinum toxin A injections into the internal anal sphincter over a period of 2 years and gained marked improvement in her symptoms. This case demonstrates the successful use of botulinum toxin A injections to relieve anal sphincter spasm and fissuring, with long-term improvement.

Complete genome sequence of the aerobic, heterotroph Marinithermus hydrothermalis type strain (T1T) from a deep-sea hydrothermal vent chimney

Energy Technology Data Exchange (ETDEWEB)

Copeland, A [U.S. Department of Energy, Joint Genome Institute; Gu, Wei [U.S. Department of Energy, Joint Genome Institute; Yasawong, Montri [HZI - Helmholtz Centre for Infection Research, Braunschweig, Germany; Lapidus, Alla L. [U.S. Department of Energy, Joint Genome Institute; Lucas, Susan [U.S. Department of Energy, Joint Genome Institute; Deshpande, Shweta [U.S. Department of Energy, Joint Genome Institute; Pagani, Ioanna [U.S. Department of Energy, Joint Genome Institute; Tapia, Roxanne [Los Alamos National Laboratory (LANL); Cheng, Jan-Fang [U.S. Department of Energy, Joint Genome Institute; Goodwin, Lynne A. [Los Alamos National Laboratory (LANL); Pitluck, Sam [U.S. Department of Energy, Joint Genome Institute; Liolios, Konstantinos [U.S. Department of Energy, Joint Genome Institute; Ivanova, N [U.S. Department of Energy, Joint Genome Institute; Mavromatis, K [U.S. Department of Energy, Joint Genome Institute; Mikhailova, Natalia [U.S. Department of Energy, Joint Genome Institute; Pati, Amrita [U.S. Department of Energy, Joint Genome Institute; Chen, Amy [U.S. Department of Energy, Joint Genome Institute; Palaniappan, Krishna [U.S. Department of Energy, Joint Genome Institute; Land, Miriam L [ORNL; Pan, Chongle [ORNL; Brambilla, Evelyne-Marie [DSMZ - German Collection of Microorganisms and Cell Cultures GmbH, Braunschweig, Germany; Rohde, Manfred [HZI - Helmholtz Centre for Infection Research, Braunschweig, Germany; Tindall, Brian [DSMZ - German Collection of Microorganisms and Cell Cultures GmbH, Braunschweig, Germany; Sikorski, Johannes [DSMZ - German Collection of Microorganisms and Cell Cultures GmbH, Braunschweig, Germany; Goker, Markus [DSMZ - German Collection of Microorganisms and Cell Cultures GmbH, Braunschweig, Germany; Detter, J. Chris [U.S. Department of Energy, Joint Genome Institute; Bristow, James [U.S. Department of Energy, Joint Genome Institute; Eisen, Jonathan [U.S. Department of Energy, Joint Genome Institute; Markowitz, Victor [U.S. Department of Energy, Joint Genome Institute; Hugenholtz, Philip [U.S. Department of Energy, Joint Genome Institute; Kyrpides, Nikos C [U.S. Department of Energy, Joint Genome Institute; Klenk, Hans-Peter [DSMZ - German Collection of Microorganisms and Cell Cultures GmbH, Braunschweig, Germany; Woyke, Tanja [U.S. Department of Energy, Joint Genome Institute

2012-01-01

Marinithermus hydrothermalis Sako et al. 2003 is the type species of the monotypic genus Marinithermus. M. hydrothermalis T1 T was the first isolate within the phylum ThermusDeinococcus to exhibit optimal growth under a salinity equivalent to that of sea water and to have an absolute requirement for NaCl for growth. M. hydrothermalis T1 T is of interest because it may provide a new insight into the ecological significance of the aerobic, thermophilic decomposers in the circulation of organic compounds in deep-sea hydrothermal vent ecosystems. This is the first completed genome sequence of a member of the genus Marinithermus and the seventh sequence from the family Thermaceae. Here we describe the features of this organism, together with the complete genome sequence and annotation. The 2,269,167 bp long genome with its 2,251 protein-coding and 59 RNA genes is a part of the Genomic Encyclopedia of Bacteria and Archaea project.

Complete genome sequence of the aerobic, heterotroph Marinithermus hydrothermalis type strain (T1(T)) from a deep-sea hydrothermal vent chimney.

Science.gov (United States)

Copeland, Alex; Gu, Wei; Yasawong, Montri; Lapidus, Alla; Lucas, Susan; Deshpande, Shweta; Pagani, Ioanna; Tapia, Roxanne; Cheng, Jan-Fang; Goodwin, Lynne A; Pitluck, Sam; Liolios, Konstantinos; Ivanova, Natalia; Mavromatis, Konstantinos; Mikhailova, Natalia; Pati, Amrita; Chen, Amy; Palaniappan, Krishna; Land, Miriam; Pan, Chongle; Brambilla, Evelyne-Marie; Rohde, Manfred; Tindall, Brian J; Sikorski, Johannes; Göker, Markus; Detter, John C; Bristow, James; Eisen, Jonathan A; Markowitz, Victor; Hugenholtz, Philip; Kyrpides, Nikos C; Klenk, Hans-Peter; Woyke, Tanja

2012-03-19

Marinithermus hydrothermalis Sako et al. 2003 is the type species of the monotypic genus Marinithermus. M. hydrothermalis T1(T) was the first isolate within the phylum "Thermus-Deinococcus" to exhibit optimal growth under a salinity equivalent to that of sea water and to have an absolute requirement for NaCl for growth. M. hydrothermalis T1(T) is of interest because it may provide a new insight into the ecological significance of the aerobic, thermophilic decomposers in the circulation of organic compounds in deep-sea hydrothermal vent ecosystems. This is the first completed genome sequence of a member of the genus Marinithermus and the seventh sequence from the family Thermaceae. Here we describe the features of this organism, together with the complete genome sequence and annotation. The 2,269,167 bp long genome with its 2,251 protein-coding and 59 RNA genes is a part of the Genomic Encyclopedia of Bacteria and Archaea project.

40 CFR 63.487 - Batch front-end process vents-reference control technology.

Science.gov (United States)

2010-07-01

... § 63.487 Batch front-end process vents—reference control technology. (a) Batch front-end process vents... 40 Protection of Environment 9 2010-07-01 2010-07-01 false Batch front-end process vents-reference control technology. 63.487 Section 63.487 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY...

Anorectal pain and irritation: anal fissure, levator syndrome, proctalgia fugax, and pruritus ani.

Science.gov (United States)

Vincent, C

1999-03-01

Anal fissures, proctalgia fugax, levator ani syndrome, and pruritus ani are common causes of anorectal pain and irritation. The clinician who obtains a thorough history and performs a complete examination can accurately diagnose these disorders. Ancillary tests seldom are helpful and rarely are necessary. Most patients suffering from these conditions readily respond to conservative therapy provided in the primary care practitioner's office.

Identification of genetic loci underlying the kernel fissure-resistance exhibited by 'cypress' and 'saber'

Science.gov (United States)

The economic value of broken rice is about half that of whole milled rice, so one goal of producers, millers, and rice breeders is to reduce broken grains that result from the dehusking and milling processes One of the primary causes of rice breakage is fissuring, or cracking, of the rice before it ...

Tensions and Fissures: The Politics of Standardised Testing and Accountability in Ontario, 1995-2015

Science.gov (United States)

Pinto, Laura Elizabeth

2016-01-01

While Ontario has received international accolades for its enactment of province-wide standardised testing upon the formation of the Education Quality and Accountability Office (EQAO), a closer look at provincial assessments over a 20-year span reveals successes as well as systemic tensions and fissures. The purpose of this paper is twofold.…

PERFORMANCE EVALUATION OF EMPIRICAL MODELS FOR VENTED LEAN HYDROGEN EXPLOSIONS

OpenAIRE

Anubhav Sinha; Vendra C. Madhav Rao; Jennifer X. Wen

2017-01-01

Explosion venting is a method commonly used to prevent or minimize damage to an enclosure caused by an accidental explosion. An estimate of the maximum overpressure generated though explosion is an important parameter in the design of the vents. Various engineering models (Bauwens et al., 2012, Molkov and Bragin, 2015) and European (EN 14994 ) and USA standards (NFPA 68) are available to predict such overpressure. In this study, their performance is evaluated using a number of published exper...

Blast venting through blanket material in the HYLIFE ICF reactor

International Nuclear Information System (INIS)

Liu, J.C.; Peterson, P.F.; Schrock, V.E.

1992-01-01

This work presents a numerical study of blast venting through various blanket configurations in the HYLIFE ICF reactor design. The study uses TSUNAMI -- a multi-dimensional, high-resolution, shock capturing code -- to predict the momentum exchange and gas dynamics for blast venting in complex geometries. In addition, the study presents conservative predictions of wall loading by gas shock and impulse delivered to the protective liquid blanket. Configurations used in the study include both 2700 MJ and 350 MJ fusion yields per pulse for 5 meter and 3 meter radius reactor chambers. For the former, an annular jet array is used for the blanket geometry, while in the latter, both annular jet array as well as slab geometries are used. Results of the study indicate that blast venting and wall loading may be manageable in the HYLIFE-II design by a judicious choice of blanket configuration

LH2 tank pressure control by thermodynamic vent system (TVS) at zero gravity

Science.gov (United States)

Wang, B.; Huang, Y. H.; Chen, Z. C.; Wu, J. Y.; Li, P.; Sun, P. J.

2017-02-01

Thermodynamic vent system (TVS) is employed for pressure control of propellant tanks at zero gravity. An analytical lumped parameter model is developed to predict pressure variation in an 18.09 m3 liquid hydrogen tank equipped with TVS. Mathematical simulations are carried out assuming tank is filled up to 75% volume (liquid mass equals to 945 kg) and is subjected to heat flux of 0.76 W/m2. Tank pressure controls at 165.5-172.4, 165.5-179.3 and 165.5-182.2 kPa are compared with reference to number of vent cycles, vent duration per cycle and loss of hydrogen. Analysis results indicate that the number of vent cycles significantly decreases from 62 to 21 when tank pressure control increases from 6.9 to 20.4 kPa. Also, duration of vent cycle increases from 63 to 152 and cycle duration decreases from 3920 to 3200 s. Further, the analysis result suggests that LH2 evaporation loss per day decreases from 0.17 to 0.14%. Based on the results of analysis, TVS is found effective in controlling the propellant tank pressure in zero gravity.

Severe accident consequence mitigation by filtered containment venting at Canadian nuclear power plants

International Nuclear Information System (INIS)

Lebel, Luke S.; Morreale, Andrew C.; Korolevych, Volodymyr; Brown, Morgan J.; Gyepi-Garbrah, Sam

2017-01-01

Highlights: • Use of filtered containment venting during a severe accident assessed. • Severe accident simulations performed using MAAP-CANDU and ADDAM. • Flow capacity, initiation protocols, efficiency, mass and thermal loading evaluated. • Efficient, robust system drastically reduces accident consequences. - Abstract: Having the capability to use filtered containment venting during a severe nuclear accident can significantly reduce its overall consequences. This study employs the MAAP-CANDU severe accident analysis code and the ADDAM atmospheric dispersion code to study the progression of: an unmitigated station blackout accident at a generic pressurized heavy water reactor, the release of radioactive material into the environment, the subsequent dispersion of the fission products through the atmosphere and the subsequent consequences (evacuation radius). The goal is to evaluate the application of filtered venting as an accident mitigation technology. Several aspects of filtered containment venting system design, like flow capacity, initiation protocols, filter efficiency, mass loading, and thermal loading are considered. An efficient and robust filtered containment venting system can reduce the amount of radiological materials emitted during an accident by 25 times or more, and as a result considerably reduce the off-site consequences of an accident.

Dynamics of hydrocarbon vents: Focus on primary porosity

Science.gov (United States)

Johansen, C.; Shedd, W.; Abichou, T.; Pineda-Garcia, O.; Silva, M.; MacDonald, I. R.

2012-12-01

This study investigated the dynamics of hydrocarbon release by monitoring activity of a single vent at a 1215m deep site in the Gulf of Mexico (GC600). An autonomous camera, deployed by the submersible ALVIN, was programmed to capture a close-up image every 4 seconds for approximately 3.5 hours. The images provided the ability to study the gas hydrate outcrop site (that measured 5.2x16.3cm3) in an undisturbed state. The outcrop included an array of 38 tube-like vents through which dark brown oil bubbles are released at a rate ranging from 8 bubbles per minute to 0 bubbles per minute. The average release of bubbles from all the separate vents was 59.5 bubbles per minute, equating the total volume released to 106.38cm per minute. The rate of bubble release decreased toward the end of the observation interval, which coincided approximately with the tidal minimum. Ice worms (Hesiocaeca methanicola, Desbruyères & Toulmond, 1998) were abundant at the vent site. The image sequence showed the ice-worms actively moving in and out of burrows in the mound. It has been speculated that Hesiocaeca methanicola contribute to gas hydrate decomposition by creating burrows and depressions in the gas hydrate matrix (Fisher et al, 2000). Ice worm burrows could generate pathways for the passage of oil and gas through the gas hydrate mound. Gas hydrates commonly occur along active and/or passive continental margins (Kennicutt et al, 1988a). The release of oil and gas at this particular hydrocarbon seep site is along a passive continental margin, and controlled primarily by active salt tectonics as opposed to the movement of continental tectonic plates (Salvador, 1987). We propose a descriptive model governing the release of gas and oil from deep sub-bottom reservoirs at depths of 3000-5000m (MacDonald, 1998), through consolidated and unconsolidated sediments, and finally through gas hydrate deposits at the sea floor. The oil and gas escape from the source rock and/or reservoir through

Process for retention of iodine and aerosols during containment venting

International Nuclear Information System (INIS)

Eckardt, B.; Betz, R.; Greger, G.U.; Werner, K.D.

1990-05-01

A process for retention of the majority of aerosols and iodine during containment venting was optimized. For this purpose, sections of a two-stage process comprising a venturi scrubber and a metal-fiber filter demister were tested under containment venting conditions assumed to prevail during a hypothetical core - melt accident and optimized with a view to achieving high decontamination factors and loading capacity while minimizing the size of the process. The loading and retention tests performed in a scrubber operating pressure range between 1 and 10 bar, at temperatures from 50 to 200degC (also boiling pools) and in air and steam atmospheres. Under these unfavorable conditions for aerosol retention, the retention efficiencies were determined at various flow rates with soluble and non-soluble aerosols as well as gaseous iodine. The retention efficiencies for BaSO 4 , uranine and SnO 2 aerosols were determined to be 99.95% to 99.99% for venturi scrubbers with metal-fiber filter demister. The retention efficiency for elemental iodine was determined to be ≥99% including revolatization effects over a 24-hour operating period. The high loading capacity of the venturi scrubber unit was verified after process modifications with various aerosols. The use of full-scale process section together with the best possible simulation of containment venting conditions by the test parameters ensured that the results can be transferred to real venting equipment. The aim of ensuring the retention of the majority of the aerosol-borne activity and of elemental iodine activity and minimizing the process size was clearly achieved and verified by means of this optimized venting equipment under an extremely wide range of hypothetical core-melt accident conditions. (orig.) With 17 refs., 3 tabs., 35 annexes [de

An abyssal mobilome: viruses, plasmids and vesicles from deep-sea hydrothermal vents.

Science.gov (United States)

Lossouarn, Julien; Dupont, Samuel; Gorlas, Aurore; Mercier, Coraline; Bienvenu, Nadege; Marguet, Evelyne; Forterre, Patrick; Geslin, Claire

2015-12-01

Mobile genetic elements (MGEs) such as viruses, plasmids, vesicles, gene transfer agents (GTAs), transposons and transpovirions, which collectively represent the mobilome, interact with cellular organisms from all three domains of life, including those thriving in the most extreme environments. While efforts have been made to better understand deep-sea vent microbial ecology, our knowledge of the mobilome associated with prokaryotes inhabiting deep-sea hydrothermal vents remains limited. Here we focus on the abyssal mobilome by reviewing accumulating data on viruses, plasmids and vesicles associated with thermophilic and hyperthermophilic Bacteria and Archaea present in deep-sea hydrothermal vents. Copyright © 2015 Institut Pasteur. Published by Elsevier Masson SAS. All rights reserved.

Radionuclide transport in a single fissure

International Nuclear Information System (INIS)

Eriksen, T.E.

1988-12-01

The study of radionuclide migration through rock is currently of great interest due to its relevance to the possible escape paths into the biosphere of radionuclides released from high level radioactive wastes burried in deep geological repositories. While water will provide the vehicle for transportation, interaction with geological material may greatly influence the radionuclide movement relative that of water. A flow system for laboratory studies of radionuclide transport in natural fissures in granitic rock under reducing conditions is described. The system based on the use of synthetic ground water equilibrated with granitic rock in a well sealed system, allow experiments to be carried out at -240 mV reduction potential. In flow experiments with technetium the retardation was found to be dependent on the method used for reducing TcO 4 - . The preparation of the tracer solutions is crucial, as some of the redox-reactions may be very slow. The dynamics of the Tc(VII) reduction and also speciation need to be carried out in separate experiments. (4 illustrations, 5 tables)

Pit and fissure sealants for preventing dental decay in the permanent teeth of children and adolescents

DEFF Research Database (Denmark)

Ahovuo-Saloranta, Anneli; Hiiri, Anne; Nordblad, Anne

2008-01-01

BACKGROUND: Although pit and fissure sealants are effective in preventing caries, their efficacy may be related to the caries prevalence in the population. OBJECTIVES: The primary objective of this review was to evaluate the caries prevention of pit and fissure sealants in children and adolescents...... for comparison of sealant versus sealant. Five split-mouth studies and one parallel group study with 5 to 10 year old children found a significant difference in favour of second or third generation resin-based sealants on first permanent molars, compared to a control without sealant, with a pooled RR of 0.13 (95...... sealant group; 27% of sealed surfaces were decayed compared to 77% of surfaces without sealant.The results of the studies comparing different sealant materials were conflicting. AUTHORS' CONCLUSIONS: Sealing is a recommended procedure to prevent caries of the occlusal surfaces of permanent molars...

Interaction of groundwater and fresh basalt fissure surfaces and its effect on the migration of actinides

International Nuclear Information System (INIS)

Vandegrift, G.F.; Bowers, D.L.; Gerding, T.J.; Fried, S.M.; Wilbur, C.K.; Seitz, M.G.

1983-01-01

Experiments are being performed at Argonne National Laboratory (ANL): (1) to identify interactions of radionuclides and repository components that effect nuclide migration, and (2) to assess changes in nuclide migration caused by modifications expected upon aging of the waste, clay backfill, and rock. The experiments are conducted with radioactive borosilicate glass, bentonite and mechanically fissured basalt rock in flowing water analogous to their configuration in a breach of a nuclear waste repository. Changes undergone by the groundwater as it passed through the fissure include: (1) drop in pH from 10 to 8, (2) loss of suspended particulate, and (3) loss of dissolved/suspended U, Np, and Pu. These effects, also studied as functions of radiation dose and of laboratory aging of the repository components, are related to the predicted long-term performance of a nuclear waste repository

Summary of measurements with MicroVent

DEFF Research Database (Denmark)

Dreau, Jerome Le; Heiselberg, Per Kvols; Jensen, Rasmus Lund

This summary presents the main results when MicroVent is used in the cooling case, without heat recovery. Experiments have thus been performed with relatively low inlet air temperature (below 15°C). Different solutions have been compared to decrease the risk of draught in the occupied zone: ‐ usi...

Inerting of a Vented Aircraft Fuel Tank Test Article with Nitrogen-Enriched Air

National Research Council Canada - National Science Library

Burns, Michael

2001-01-01

...) required to inert a vented aircraft fuel tank. NEA, generated by a hollow fiber membrane gas separation system, was used to inert a laboratory fuel tank with a single vent on top designed to simulate a transport category airplane fuel tank...

Clinical, manometric, and ultrasonographic results of pneumatic balloon dilatation vs. lateral internal sphincterotomy for chronic anal fissure: a prospective, randomized, controlled trial.

Science.gov (United States)

Renzi, Adolfo; Izzo, Domenico; Di Sarno, Giandomenico; Talento, Pasquale; Torelli, Francesco; Izzo, Giuseppe; Di Martino, Natale

2008-01-01

This prospective, randomized, controlled trial was designed to compare the clinical, functional, and morphologic results of pneumatic balloon dilatation with lateral internal sphincterotomy for the treatment of chronic anal fissure. All patients with symptomatic chronic anal fissure were randomly assigned to pneumatic balloon dilatation or lateral internal sphincterotomy and invited to complete a standardized questionnaire inquiring about their symptoms. Anal ultrasonography and anal manometry were performed before and six months after surgery. A proctologic examination was performed between the fifth and sixth postoperative weeks. Anal continence, scored by using a validated continence grading scale, was evaluated preoperatively at 1 and 6 weeks and at 12 and 24 months. Fifty-three patients, who satisfied selection criteria, were enrolled in the trial. Four patients (7.5 percent) were lost to follow-up. Twenty-four patients (11 males; mean age, 42 +/- 8.2 years) underwent pneumatic balloon dilatation and 25 patients (10 males; mean age, 44 +/- 7.3 years) underwent lateral internal sphincterotomy. Fissure-healing rates were 83.3 percent in the pneumatic balloon dilatation and 92 percent in the lateral internal sphincterotomy group. Recurrent anal fissure was observed in one patient (4 percent) after lateral internal sphincterotomy. At anal manometry, mean resting pressure decrements obtained after pneumatic balloon dilatation and lateral internal sphincterotomy were 30.5 and 34.3 percent, respectively. After pneumatic balloon dilatation, anal ultrasonography did not show any significant sphincter damage. At 24-month follow-up, the incidence of incontinence, irrespective of severity, was 0 percent in the pneumatic balloon dilatation group and 16 percent in the lateral internal sphincterotomy group (P < 0.0001). As lateral internal sphincterotomy, pneumatic balloon dilatation grants a high anal fissure-healing rate but with a statistically significant reduction in

Primary Formation Path of Formaldehyde in Hydrothermal Vents

Science.gov (United States)

Inaba, Satoshi

2018-03-01

Formaldehyde is abundant in the universe and one of the fundamental molecules for life. Hydrothermal vents produce a substantial amount of hydrogen molecules by serpentinization and promote reductive reactions of single carbon compounds. The abundance of formaldehyde is expected to be low due to the high Gibbs free energy in hydrothermal vents. We consider two competing formation pathways of formaldehyde: (1) the reduction of CO by H2 and (2) the reduction of HCOOH by H2 to form a methanediol, followed by the dehydration of the methanediol. We performed a number of quantum chemical simulations to examine the formation of formaldehyde in the gas phase as well as in aqueous solution. The energy barrier is significantly reduced by the catalytic effect of water molecules in aqueous solution and becomes lowest when a water cluster consisted of 5 water molecules catalyzes the reduction. The energy barrier to form a methanediol by the reduction of HCOOH is lower by 17.5 kcal/mol than that to form a formaldehyde by the reduction of CO. Considering the low energy barrier to dehydrate methanediol, the primary pathway to form formaldehyde in hydrothermal vents is concluded to be the reduction of HCOOH by H2, followed by the dehydration of methanediol.

Molecular isotopic evidence for anaerobic oxidation of methane in deep-sea hydrothermal vent environment in Okinawa Trough

Science.gov (United States)

Uchida, M.; Takai, K.; Inagaki, F.

2003-04-01

Large amount of methane in anoxic marine sediments as well as cold seeps and hydrothermal vents is recycled through for an anoxic oxidation of methane processes. Now that combined results of field and laboratory studies revealed that microbiological activity associated with syntrophic consortium of archaea performing reversed methanogenesis and sulfate-reducing bacteria is significant roles in methane recycling, anaerobic oxidation of methane (AOM). In this study, we examined the diversity of archaeal and bacterial assemblages of AOM using compound-specific stable carbon isotopic and phylogenetic analyses. "Iheya North" in Okinawa Trough is sediment-rich, back arc type hydrothermal system (27^o47'N, 126^o53'E). Sediment samples were collected from three sites where are "bubbling sites", yellow-colored microbial mats are formed with continuous bubbling from the seafloor bottom, vent mussel's colonies site together with slowly venting and simmering, and control site off 100 m distance from thermal vent. This subsea floor structure has important effect in the microbial ecosystem and interaction between their activity and geochemical processes in the subseafloor habitats. Culture-independent, molecular biological analysis clearly indicated the presence of thermophilic methanogens in deeper area having higher temperatures and potential activity of AMOs consortium in the shallower area. AMO is composed with sulfate-reducing bacterial components (Desulfosarcina spp.) and anoxic methane oxidizing archaea (ANME-2). These results were consistent with the results of compound-specific carbon analysis of archaeal biomarkers. They showed extremely depleted 13C contents (-80 ppm ˜ -100 ppm), which also appeared to be capable of directly oxidizing methane.

Potential Flammable Gas Explosion in the TRU Vent and Purge Machine

International Nuclear Information System (INIS)

Vincent, A

2006-01-01

The objective of the analysis was to determine the failure of the Vent and Purge (V and P) Machine due to potential explosion in the Transuranic (TRU) drum during its venting and/or subsequent explosion in the V and P machine from the flammable gases (e.g., hydrogen and Volatile Organic Compounds [VOCs]) vented into the V and P machine from the TRU drum. The analysis considers: (a) increase in the pressure in the V and P cabinet from the original deflagration in the TRU drum including lid ejection, (b) pressure wave impact from TRU drum failure, and (c) secondary burns or deflagrations resulting from excess, unburned gases in the cabinet area. A variety of cases were considered that maximized the pressure produced in the V and P cabinet. Also, cases were analyzed that maximized the shock wave pressure in the cabinet from TRU drum failure. The calculations were performed for various initial drum pressures (e.g., 1.5 and 6 psig) for 55 gallon TRU drum. The calculated peak cabinet pressures ranged from 16 psig to 50 psig for various flammable gas compositions. The blast on top of cabinet and in outlet duct ranged from 50 psig to 63 psig and 12 psig to 16 psig, respectively, for various flammable gas compositions. The failure pressures of the cabinet and the ducts calculated by structural analysis were higher than the pressure calculated from potential flammable gas deflagrations, thus, assuring that V and P cabinet would not fail during this event. National Fire Protection Association (NFPA) 68 calculations showed that for a failure pressure of 20 psig, the available vent area in the V and P cabinet is 1.7 to 2.6 times the required vent area depending on whether hydrogen or VOCs burn in the V and P cabinet. This analysis methodology could be used to design the process equipment needed for venting TRU waste containers at other sites across the Department of Energy (DOE) Complex

Parents' Attitude towards the Use of Fluorides and Fissure Sealants and its Effect on their Children's Oral Health.

Science.gov (United States)

Blumer, Sigalit; Ratson, Tal; Peretz, Benjamin; Dagon, Nurit

To characterize the attitudes of Israeli parents towards caries preventive measures. participating parents completed a 21-item questionnaire on their demographics, dental history, attitudes and satisfaction from fluorides and fissure sealants. One hundred parents (average age 41.62±4.9 years, 85 females) participated. Most of the parents (88% of the mothers and 84% of the fathers) had an academic education. Most of the parents (54%) had a favorable attitude towards the use of fluoridated gels, while only 37% of them had a positive opinion regarding fluoridated water. The satisfaction levels were very high regarding fissure sealants, fluoridated mouth rinses and fluoridated gels (78.1%, 73.6% and 72.5% respectively). The satisfaction from fluoridated water was split almost equally (50.8% were 'pleased' and 49.2% 'not pleased'). The main source for parental oral health knowledge was the dentist (83%). Parents' attitude towards caries preventive measures was significantly correlated to their gender, dental experience, level of education and the number of children in the family. positive attitude towards caries preventive measures was found among parents with higher awareness for preventive oral health measures and among bigger families. Mothers were more positive about fissure sealants than fathers. Mothers with up to 12 years of education tended to have a positive opinion regarding water fluoridation.

Geomicrobiology of Hydrothermal Vents in Yellowstone Lake: Phylogenetic and Functional Analysis suggest Importance of Geochemistry (Invited)

Science.gov (United States)

Inskeep, W. P.; Macur, R.; Jay, Z.; Clingenpeel, S.; Tenney, A.; Lavalvo, D.; Shanks, W. C.; McDermott, T.; Kan, J.; Gorby, Y.; Morgan, L. A.; Yooseph, S.; Varley, J.; Nealson, K.

2010-12-01

Yellowstone Lake (Yellowstone National Park, WY, USA) is a large, high-altitude, fresh-water lake that straddles the most recent Yellowstone caldera, and is situated on top of significant hydrothermal activity. An interdisciplinary study is underway to evaluate the geochemical and geomicrobiological characteristics of several hydrothermal vent environments sampled using a remotely operated vehicle, and to determine the degree to which these vents may influence the biology of this young freshwater ecosystem. Approximately six different vent systems (locations) were sampled during 2007 and 2008, and included water obtained directly from the hydrothermal vents as well as biomass and sediment associated with these high-temperature environments. Thorough geochemical analysis of these hydrothermal environments reveals variation in pH, sulfide, hydrogen and other potential electron donors that may drive primary productivity. The concentrations of dissolved hydrogen and sulfide were extremely high in numerous vents sampled, especially the deeper (30-50 m) vents located in the Inflated Plain, West Thumb, and Mary Bay. Significant dilution of hydrothermal fluids occurs due to mixing with surrounding lake water. Despite this, the temperatures observed in many of these hydrothermal vents range from 50-90 C, and elevated concentrations of constituents typically associated with geothermal activity in Yellowstone are observed in waters sampled directly from vent discharge. Microorganisms associated with elemental sulfur mats and filamentous ‘streamer’ communities of Inflated Plain and West Thumb (pH range 5-6) were dominated by members of the deeply-rooted bacterial Order Aquificales, but also contain thermophilic members of the domain Archaea. Assembly of metagenome sequence from the Inflated Plain vent biomass and to a lesser extent, West Thumb vent biomass reveal the importance of Sulfurihydrogenibium-like organisms, also important in numerous terrestrial geothermal

Method of estimating maximum VOC concentration in void volume of vented waste drums using limited sampling data: Application in transuranic waste drums

International Nuclear Information System (INIS)

Liekhus, K.J.; Connolly, M.J.

1995-01-01

A test program has been conducted at the Idaho National Engineering Laboratory to demonstrate that the concentration of volatile organic compounds (VOCs) within the innermost layer of confinement in a vented waste drum can be estimated using a model incorporating diffusion and permeation transport principles as well as limited waste drum sampling data. The model consists of a series of material balance equations describing steady-state VOC transport from each distinct void volume in the drum. The primary model input is the measured drum headspace VOC concentration. Model parameters are determined or estimated based on available process knowledge. The model effectiveness in estimating VOC concentration in the headspace of the innermost layer of confinement was examined for vented waste drums containing different waste types and configurations. This paper summarizes the experimental measurements and model predictions in vented transuranic waste drums containing solidified sludges and solid waste

Food-web complexity across hydrothermal vents on the Azores triple junction

Science.gov (United States)

Portail, Marie; Brandily, Christophe; Cathalot, Cécile; Colaço, Ana; Gélinas, Yves; Husson, Bérengère; Sarradin, Pierre-Marie; Sarrazin, Jozée

2018-01-01

The assessment and comparison of food webs across various hydrothermal vent sites can enhance our understanding of ecological processes involved in the structure and function of biodiversity. The Menez Gwen, Lucky Strike and Rainbow vent fields are located on the Azores triple junction of the Mid-Atlantic Ridge. These fields have distinct depths (from 850 to 2320 m) and geological contexts (basaltic and ultramafic), but share similar faunal assemblages defined by the presence of foundation species that include Bathymodiolus azoricus, alvinocarid shrimp and gastropods. We compared the food webs of 13 faunal assemblages at these three sites using carbon and nitrogen stable isotope analyses (SIA). Results showed that photosynthesis-derived organic matter is a negligible basal source for vent food webs, at all depths. The contribution of methanotrophy versus autotrophy based on Calvin-Benson-Bassham (CBB) or reductive tricarboxylic acid (rTCA) cycles varied between and within vent fields according to the concentrations of reduced compounds (e.g. CH4, H2S). Species that were common to vent fields showed high trophic flexibility, suggesting weak trophic links to the metabolism of chemosynthetic primary producers. At the community level, a comparison of SIA-derived metrics between mussel assemblages from two vent fields (Menez Gwen & Lucky Strike) showed that the functional structure of food webs was highly similar in terms of basal niche diversification, functional specialization and redundancy. Coupling SIA to functional trait approaches included more variability within the analyses, but the functional structures were still highly comparable. These results suggest that despite variable environmental conditions (physico-chemical factors and basal sources) and faunal community structure, functional complexity remained relatively constant among mussel assemblages. This functional similarity may be favoured by the propensity of species to adapt to fluid variations and

Multiple-vent programme to test the pressure suppression system

International Nuclear Information System (INIS)

Aust, E.; Schwan, H.; Vollbrandt, I.

1979-01-01

Three pre-tests with a multiple vent configuration have been performed at the GKSS pressure suppression test facility. First test results indicate significant chugging events with occur periodically with 0.4 to 0.2 Hz. These events appear simultaneously in less than 10 ms at the exit of the three vent pipes and cause pressure pulses in the range of 3 bar. This report gives a short description of the test facility and presents the boundary conditions of the test facility and presents the boundary conditions of the three pre-tests, test results and a first valuation of the experimental informations. (orig.) [de

Examining Design Factors for Safe and Effective Hydrogen Vents for Waste Packages

International Nuclear Information System (INIS)

Herrmann, R.C.

2009-01-01

The possibility of a nuclear renaissance, and the possibility of large scale new build to meet both the concerns of the environmental lobby and the economic imperatives created by the political hostage taking of unreliable fossil fuel markets throughout the world, coupled with the need to resolve issues still outstanding from a previous generation of wastes create the need for a widely accepted understanding of the needs for venting waste packages which are being prepared for term storage. In the US the technologies to immobilising the legacy wastes are being developed, in the UK the NDA is gearing up to decommission a range of sites and throughout Europe facilities are being demolished and the wastes taken to term storage. In several cases, the waste containers require venting, both to allow the thermal relief of the container during climatic variation and to allow the venting of generated gases from radiolysis, decomposition and corrosion of the contents, including Hydrogen and Hydrocarbons. The paper will examine the disparate demands of the market place, and propose strategies to rationalise the specification of filter breathers so that both producers and users have a common framework from which to determine their individual venting needs. Examining the mutually exclusive demands of permeability (affecting both pressure differential and Hydrogen diffusion) and filtration efficiency, the paper will explore economic solutions in an attempt to provide a framework against which the large number of waste containers requiring venting in the future can have their vent filters designed to meet both the best possible combination of efficiency and permeability, as well as exploring the limits of knowledge of corrosion of the filter media and suggesting strategies to tackle the possibility of the filter media failing before the waste container, and the consequences of such an event. (authors)

An Assessment for A Filtered Containment Venting Strategy Using Decision Tree Models

International Nuclear Information System (INIS)

Shin, Hoyoung; Jae, Moosung

2016-01-01

In this study, a probabilistic assessment of the severe accident management strategy through a filtered containment venting system was performed by using decision tree models. In Korea, the filtered containment venting system has been installed for the first time in Wolsong unit 1 as a part of Fukushima follow-up steps, and it is planned to be applied gradually for all the remaining reactors. Filtered containment venting system, one of severe accident countermeasures, prevents a gradual pressurization of the containment building exhausting noncondensable gas and vapor to the outside of the containment building. In this study, a probabilistic assessment of the filtered containment venting strategy, one of the severe accident management strategies, was performed by using decision tree models. Containment failure frequencies of each decision were evaluated by the developed decision tree model. The optimum accident management strategies were evaluated by comparing the results. Various strategies in severe accident management guidelines (SAMG) could be improved by utilizing the methodology in this study and the offsite risk analysis methodology

An Assessment for A Filtered Containment Venting Strategy Using Decision Tree Models

Energy Technology Data Exchange (ETDEWEB)

Shin, Hoyoung; Jae, Moosung [Hanyang University, Seoul (Korea, Republic of)

2016-10-15

In this study, a probabilistic assessment of the severe accident management strategy through a filtered containment venting system was performed by using decision tree models. In Korea, the filtered containment venting system has been installed for the first time in Wolsong unit 1 as a part of Fukushima follow-up steps, and it is planned to be applied gradually for all the remaining reactors. Filtered containment venting system, one of severe accident countermeasures, prevents a gradual pressurization of the containment building exhausting noncondensable gas and vapor to the outside of the containment building. In this study, a probabilistic assessment of the filtered containment venting strategy, one of the severe accident management strategies, was performed by using decision tree models. Containment failure frequencies of each decision were evaluated by the developed decision tree model. The optimum accident management strategies were evaluated by comparing the results. Various strategies in severe accident management guidelines (SAMG) could be improved by utilizing the methodology in this study and the offsite risk analysis methodology.

Isotope techniques in the study of the hydrology of fractured and fissured rocks

International Nuclear Information System (INIS)

1989-01-01

It is generally agreed that the hydrology of fractured rocks refers to the occurrence and movement of groundwater in rocks whose porosity is due to cracks, fissures and fractures in compact rocks. Until recently, crystalline rocks were considered to be impervious (the role of karst reservoirs for groundwater storage is already known). Thus, although fractured rocks cover approximately one-third of the Earth's surface, knowledge of groundwater flow dynamics still needs to be substantively improved. The Proceedings include the papers presented at the Advisory Group Meeting on the Application of Isotope Techniques in the Study of the Hydrology of Fractured and Fissured Rocks, which took place in Vienna from 17 to 21 November 1986. The meeting was attended by 21 scientists from 10 Member States. The Group agreed that the following topics should be given the highest priority: (1) Protection of groundwater resources should be incorporated into all future activities. This implies that recharge areas have to be delineated, not only using nuclear techniques but also other hydrogeological and geochemical methods. Research efforts in this direction should be intensified. (2) The Group was aware that new isotope techniques are being developed in hydrogeology and agreed that their application in fractured and fissured rocks showed promise. It was therefore suggested that information on new isotopes such as 36 Cl and 129 I should be gathered, either in the form of the various techniques currently being used by different laboratories or through the various activities that are being undertaken. Ways of co-ordinating the work being done and exchanging information at the international level should be encouraged. The Proceedings should be of interest to scientists responsible for the evaluation of water resources in crystalline rocks. It is hoped that hydrologists and hydrogeologists working in such terrains who are not familiar with the use of isotope techniques will find ideas and

Technology Solutions Case Study: Evaluation of Passive Vents in New-Construction Multifamily Buildings

Energy Technology Data Exchange (ETDEWEB)

S. Puttagunta, S. Maxwell, D. Berger, and M. Zuluaga

2015-10-01

The Consortium for Advanced Residential Buildings (CARB) conducted research to gain more insight into passive vents. Because passive vents are meant to operate in a general environment of negative apartment pressure, the research assessed whether these negative pressures prevail through a variety of environmental conditions.

Increased diversity of sessile epibenthos at subtidal hydrothermal vents: seven hypotheses based on observations at Milos Island, Aegean Sea

Directory of Open Access Journals (Sweden)

Carlo Nike Bianchi

2011-06-01

Full Text Available Research on subtidal hydrothermal vent ecosystems at Milos, Hellenic Volcanic Arc (Aegean Sea, suggested that vent activity increased the species richness of sessile epibenthic assemblages. Based on 303 species found in 6 sites (3 close to vents, 3 farther away, the present paper uses correspondence analysis and species/samples curves to examine the species composition and richness of these assemblages. Differences due to vent proximity were more important than those due to bottom depth and distance from the shore. Diversity was confirmed to be higher near the vents, although none of the 266 species found at the vent sites can be considered as obligate vent-associated species. Seven different, although not mutually exclusive, hypotheses are discussed to explain the pattern of increased epibenthic species diversity at the vent sites, namely: (i vents represent an intermediate disturbance, inducing mortality by the emission of toxic fluids; (ii higher winter temperature allows for the occurrence of warm-water species, which add to the regional background; (iii venting disrupts the homogeneity of the water bottom layer, increasing bottom roughness and hence habitat heterogeneity; (iv deposition of minerals and enhanced bioconstruction by Ca enrichment increment habitat provision; (v fluid emission induces advective mechanisms that favour recruitment; (vi vents emit CO2, nutrients and trace elements that enhance primary productivity; and (vii bacterial chemosynthesis add to photosynthesis to provide a diversity of food sources for the fauna.

Subseafloor Microbial Life in Venting Fluids from the Mid Cayman Rise Hydrothermal System

Science.gov (United States)

Huber, J. A.; Reveillaud, J.; Reddington, E.; McDermott, J. M.; Sylva, S. P.; Breier, J. A.; German, C. R.; Seewald, J.

2012-12-01

In hard rock seafloor environments, fluids emanating from hydrothermal vents are one of the best windows into the subseafloor and its resident microbial community. The functional consequences of an extensive population of microbes living in the subseafloor remains unknown, as does our understanding of how these organisms interact with one another and influence the biogeochemistry of the oceans. Here we report the abundance, activity, and diversity of microbes in venting fluids collected from two newly discovered deep-sea hydrothermal vents along the ultra-slow spreading Mid-Cayman Rise (MCR). Fluids for geochemical and microbial analysis were collected from the Von Damm and Piccard vent fields, which are located within 20 km of one another, yet have extremely different thermal, geological, and depth regimes. Geochemical data indicates that both fields are highly enriched in volatiles, in particular hydrogen and methane, important energy sources for and by-products of microbial metabolism. At both sites, total microbial cell counts in the fluids ranged in concentration from 5 x 10 4 to 3 x 10 5 cells ml-1 , with background seawater concentrations of 1-2 x 10 4 cells ml-1 . In addition, distinct cell morphologies and clusters of cells not visible in background seawater were seen, including large filaments and mineral particles colonized by microbial cells. These results indicate local enrichments of microbial communities in the venting fluids, distinct from background populations, and are consistent with previous enumerations of microbial cells in venting fluids. Stable isotope tracing experiments were used to detect utilization of acetate, formate, and dissolve inorganic carbon and generation of methane at 70 °C under anaerobic conditions. At Von Damm, a putatively ultra-mafic hosted site located at ~2200 m with a maximum temperature of 226 °C, stable isotope tracing experiments indicate methanogenesis is occurring in most fluid samples. No activity was detected

Stereoscopic particle image velocimetry investigations of the mixed convection exchange flow through a horizontal vent

Science.gov (United States)

Varrall, Kevin; Pretrel, Hugues; Vaux, Samuel; Vauquelin, Olivier

2017-10-01

The exchange flow through a horizontal vent linking two compartments (one above the other) is studied experimentally. This exchange is here governed by both the buoyant natural effect due to the temperature difference of the fluids in both compartments, and the effect of a (forced) mechanical ventilation applied in the lower compartment. Such a configuration leads to uni- or bi-directional flows through the vent. In the experiments, buoyancy is induced in the lower compartment thanks to an electrical resistor. The forced ventilation is applied in exhaust or supply modes and three different values of the vent area. To estimate both velocity fields and flow rates at the vent, measurements are realized at thermal steady state, flush the vent in the upper compartment using stereoscopic particle image velocimetry (SPIV), which is original for this kind of flow. The SPIV measurements allows the area occupied by both upward and downward flows to be determined.

Venting device for nuclear reactor container

International Nuclear Information System (INIS)

Yamashita, Masahiro; Ogata, Ken-ichi.

1994-01-01

An airtight vessel of a venting device of a nuclear reactor container is connected with a reactor container by way of a communication pipeline. A feed water tank is disposed at a position higher than the liquid surface of scrubbing water in the airtight vessel for supplying scrubbing water to the airtight vessel. In addition, a scrubbing water storage tank is disposed at a position hither than the feed water tank for supplying scrubbing water to the feed water tank. Storage water in the feed water tank is introduced into the airtight vessel by the predetermined opening operation of a valve by the pressure exerted on the liquid surface and the own weight of the storage water. Further, the storage water in the scrubbing water storage tank is led into the feed water tank by the water head pressure. The scrubbing water for keeping the performance of the venting device of the reactor container can be supplied by a highly reliable method without using AC power source or the like as a driving source. (I.N.)

Simulating Electrochemistry of Hydrothermal Vents on Enceladus and Other Ocean Worlds

Science.gov (United States)

Barge, L. M.; Krause, F. C.; Jones, J. P.; Billings, K.; Sobron, P.

2017-12-01

Gradients generated in hydrothermal systems provide a significant source of free energy for chemosynthetic life, and may play a role in present-day habitability on ocean worlds such as Enceladus that are thought to host hydrothermal activity. Hydrothermal vents are similar in some ways to typical fuel cell devices: redox/pH gradients between seawater and hydrothermal fluid are analogous to the oxidant and fuel reservoirs; conductive natural mineral deposits are analogous to electrodes; and, in hydrothermal chimneys, the porous chimney wall can function as a separator or ion-exchange membrane. Electrochemistry, founded on quantitative study of redox and other chemical disequilibria as well as the chemistry of interfaces, is uniquely suited to studying these systems. We have performed electrochemical studies to better understand the catalytic potential of seafloor minerals and vent chimneys, using samples from a black smoker vent chimney as an initial demonstration. Fuel cell experiments with electrodes made from black smoker chimney material accurately simulated the redox reactions that occur in a geological setting with this particular catalyst. Similar methods with other geo-catalysts (natural or synthetic) could be utilized to test which redox reactions or metabolisms could be driven in other hydrothermal systems, including putative vent systems on other worlds.

Hunting for Hydrothermal Vents at the Local-Scale Using AUV's and Machine-Learning Classification in the Earth's Oceans

Science.gov (United States)

White, S. M.

2018-05-01

New AUV-based mapping technology coupled with machine-learning methods for detecting individual vents and vent fields at the local-scale raise the possibility of understanding the geologic controls on hydrothermal venting.

A model for the calculation of vent clearing transients in pressure suppression systems

International Nuclear Information System (INIS)

Brosche, D.

1975-01-01

For the layout of a pressure suppression system of a light water cooled reactor (boiling water reactor) it is important to know the time dependent behavior of the vent clearing transient after a loss-of-coolant accident for two main reasons: time of the end of the vent clearing transient influences strongly the pressure and temperature maxima in the drywell and wetwell. Time-dependent behavior of the vent clearing transient influences pressure loads in the condensation pool of the wetwell and therefore pressure induced stresses to the structure. The time-dependent behavior of the water masses in the vent pipes and wetwell are described by the basic equations for a nonstationary incompressible friction flow: momentum equation, continuity equation and a correlation for the variation of the state of the gas volume in the wetwell above the water level. After many algebraic operations and integrations along the flow path, a single ordinary nonlinear differential equation for the variations of the water levels in the vent pipes and wetwell is obtained. Therefore the time-dependent velocities and accelerations of the water levels and the moment of the end clearing transient are known. The time-dependent pressure behavior in the drywell, geometrical conditions, initial submergence depth of the vent pipes and different friction and pressure loss factors are presented. The theoretical model has been tested at corresponding experiments performed at a full scale 1/48 segment of the Humboldt Bay pressure suppression containment in the USA and at the pressure suppression containment at the Marviken nuclear power station in Sweden. All these comparisons have shown good agreement between theory and experiment

Filtered atmospheric venting of LWR containments: the Swedish research programme and design concepts

International Nuclear Information System (INIS)

Graeslund, C.; Johansson, K.; Nilsson, L.; Tiren, I.

1981-01-01

An investigation of filtered atmospheric venting of LWR containments has been recommended by a governmental reactor safety committee as a means of reducing the large releases of radioactivity which it is believed could arise as a result of accidents beyond the design bases (class 9) in nuclear power plants. The purpose of the project is to provide the technical basis for evaluating the feasibility, effectiveness and costs of some vent filter design concepts. The main design objective is substantially to reduce releases to the atmosphere of those radioactive substances which could cause long-lasting contamination of large land areas resulting from accidents beyond the design basis. The degree to which that objective can be reached by applying vent-filter functions becomes the main design evaluation criterion. The governing principle for the vent filter design is to utilize passive components and functions to the greatest possible extent. The design concept is to vent the stream and gases from the containment into an underground tunnel containing a large bed of gravel where the steam is condensed. Non-condensable gases are vented through a sand filter at the outlet of the tunnel via a stack to the atmosphere. The tunnel volume envisaged is of the order of 100,000m 3 , and the length about 1000m. A deep tunnel in rock can be made to withstand the pressures from the burning of hydrogen-air mixtures. As an alternative method the condensing and filtering functions can be achieved by utilizing water pools built sub-surface in concrete structures. Concrete structures can also be built to withstand hydrogen burning. (author)

Randomized clinical trial assessing the side-effects of glyceryl trinitrate and diltiazem hydrochloride in the treatment of chronic anal fissure.

Science.gov (United States)

Kocher, H M; Steward, M; Leather, A J M; Cullen, P T

2002-04-01

Glyceryl trinitrate (GTN) ointment (0 small middle dot2 per cent) has an efficacy of up to 68 per cent in healing chronic anal fissure, but with headache as a major side-effect. Diltiazem hydrochloride (DTZ) cream (2 per cent) is expected to have fewer side-effects. A prospective double-blind randomized two-centre trial requiring at least 26 patients in each group (alpha = 0.05, beta = 0.9) was instituted after approval of the local ethics committee, to compare the incidence of side-effects (primary endpoint) with 0.2 per cent GTN ointment and 2 per cent DTZ cream in the treatment of chronic anal fissure. Treatments were applied perianally, twice daily for 6-8 weeks. All patients gave written informed consent. Both groups were comparable in patient demographics and clinical characteristics. Twelve patients violated the protocol, withdrew or did not attend follow-up. There were more side-effects with GTN (21 of 29 patients) than with DTZ (13 of 31) (relative risk (RR) 1.84 (95 per cent confidence interval (c.i.) 1.11 to 3.04), P = 0.01). In particular, more headaches occurred with GTN (17 of 29 patients) than with DTZ (eight of 31) (RR 2.06 (95 per cent c.i. 1.18 to 3.59), P = 0.01). There were no significant differences in healing and symptomatic improvement rates between patients receiving GTN (25 of 29) and DTZ (24 of 31). DTZ cream caused substantially fewer headaches than GTN ointment. There was no significant difference in the healing or improvement of chronic anal fissure between the treatments. DTZ may be the preferred first-line treatment for chronic anal fissure.

Blurring of the vessels of the interhemispheric fissure in multislice CT angiography: a sign of meningeal carcinomatosis

International Nuclear Information System (INIS)

Ertl-Wagner, Birgit B.; Hoffmann, Ralf-Thorsten; Herrmann, Karin; Reiser, Maximilian F.; Bruening, Roland; Dichgans, Martin

2004-01-01

Meningeal carcinomatosis remains a challenging diagnosis to make, with both cerebrospinal fluid (CSF) analysis and radiological methods having a limited sensitivity. We aimed at describing a possible diagnostic sign of multislice CT angiography (MS-CTA) in the diagnosis of meningeal carcinomatosis. Upon retrospective analysis of MSCT angiographies of the brain, a conspicuous sign of the vessels of the interhemispheric fissure was noted in five patients. Cranial MSCT angiographies were performed with a standardized protocol (120 kV, 200 mA s, collimation of 4 x 1 mm, table feed per rotation 4 mm). We injected 120 ml of nonionic contrast medium as a bolus, and data acquisition was started after a fixed delay of 35 s. In order to elucidate the finding, correlation with clinical follow-up and/or CSF findings was performed for all patients. In five patients there was a blurring, an increased number, and a pathologic configuration of the vessels of the interhemispheric fissure. All five patients with this sign had clinical signs and symptoms of meningeal carcinomatosis. Three patients had positive CSF cytology, one further patient had follow-up spinal MRI 6 weeks later demonstrating meningeal carcinomatosis. One patient declined lumbar puncture. MS-CTA has the capacity to demonstrate a pathologic configuration of the vessels of the interhemispheric fissure in patients with meningeal carcinomatosis. This sign may serve as an indicator of meningeal carcinomatosis and should raise the suspicion of this disease entity. (orig.)

Modelling of particles collection by vented limiters

International Nuclear Information System (INIS)

Tsitrone, E.; Pegourie, B.; Granata, G.

1995-01-01

This document deals with the use of vented limiters for the collection of neutral particles in Tore Supra. The model developed for experiments is presented together with its experimental validation. Some possible improvements to the present limiter are also proposed. (TEC). 5 refs., 3 figs

Endosonographic and manometric evaluation of internal anal sphincter in patients with chronic anal fissure and its correlation with clinical outcome after topical glyceryl trinitrate therapy.

Science.gov (United States)

Pascual, Marta; Pera, Miguel; Courtier, Ricard; Gil, Mariá José; Parés, David; Puig, Sonia; Andreu, Montserrat; Grande, Luis

2007-08-01

Anorectal pressure studies have demonstrated internal anal sphincter (IAS) hypertonia in patients with chronic anal fissure. It is unknown however, if these changes in IAS function are associated with any abnormality in sphincter morphology. The first aim was to investigate the clinical characteristics and the manometric and endosonographic findings of the IAS in a cohort of patients with chronic anal fissure. The second aim was to investigate the association between these findings and the outcome with topical Glyceryl trinitrate (GTN) therapy. All patients who presented with chronic anal fissure from November 1999 to May 2004 were included after failure of conservative therapy. Anorectal manometry and anal endosonography were performed before treatment with 0.2% GTN ointment twice daily was initiated. Patients were evaluated after 8 weeks. One hundred and twenty-four patients (66 women, mean age, 45.2 +/- 14.8 years) were included. Hypertonia of the IAS was found in 84 (68%) patients. The mean maximum IAS thickness was 3.6 +/- 0.76 mm (1.6-5.5). An abnormally thick IAS, adjusted by age, was observed in 113 (91.1%) patients. We found no correlation between resting pressure and IAS thickness (r = 0.074; p = 0.41). At 8 weeks, 52 patients (42%) had healed with complete symptoms resolution. No statistically significant differences were observed when clinical features and manometric and endosonographic findings were compared between healing and no-healing fissures. The majority of patients with chronic anal fissure present an abnormally thick IAS. Clinical, manometric and endosonographic features had no association with outcome after GTN treatment.

Water column imaging on hydrothermal vent in Central Indian Ridge

Science.gov (United States)

Koh, J.; Park, Y.

2017-12-01

Water column imaging with Multibeam echosounder systems (MBES) is recently becoming of increasing interest for oceanographic studies. Especially gas bubbles and hot water exposed from hydrothermal vents make acoustic impedance anomalies in cold seawater, water column imaging is very useful for the researchers who want to detect some kinds of hydrothermal activity. We conducted a hydrothermal exploration program, called "INVENT17", using the MBES system, KONGBERG EM122 (12kHz, 1°×1°), mounted on R/V ISABU and we deployed other equipments including video guided hydraulic grab, tow-yo CTD and general CTD with MAPR (Miniature Autonomous Plume Recorder) in 2017. First, to evaluate its capabilities of detection of hydrothermal vent, the surveys using the MBES were conducted at the Solitaire Field, previously identified hydrothermal area of the Central Indian Ridge. The bathymetric data obtained from MBES provided information about detailed morphology of seafloor, but we were not able to achieve the information from the water column imaging data. But the clue of existence of active hydrothermal vent was detected through the values of ΔNTU, dEh/dt, and OPR gained from MAPR, the data means that the hydrothermal activity affects 100m from the seafloor. It could be the reason that we can't find the hydrothermal activity because the range resolution of water column imaging is pretty rough so that the size of 100m-scaled activity has low possibility to distinguish from seafloor. The other reason is there are no sufficient objects to cause strong scattering like as CO2 bubbles or droplets unlike in the mid-Okinawa Trough. And this suggests that can be a important standard to identify properties of hydrothermal vent sites depending on the presence of scattering objects in water mass. To justify this, we should perform more chemical analysis of hot water emanating from hydrothermal vent and collected several bottles of water sample to do that.

Capillary Discourses, Fissure Points, and Tacitly Confessing the Self: Foucault's Later Work and Educational Research

Science.gov (United States)

Worthman, Christopher; Troiano, Beverly

2016-01-01

This article draws on Foucault's later work to consider in an exploratory but specific way how that work can inform educational research. It introduces the concepts of "capillary discourses" and "fissure points" to show, by way of example, how a regime of truth such as neoliberalism shapes lifelong learning theory, the pedagogy…

Environmental & Water Quality Operational Studies: Improvement of Hydropower Release Dissolved Oxygen with Turbine Venting.

Science.gov (United States)

1987-03-01

VENTED HYDROTURBINE .. 38 Model Development .......................................... 38 Model Application...mouth intake (Figures B26-B27). 37 A F -W V .0P V *W V *. V. VW . i. ~ ~ -% PART V: MODELING OF REAERATION THROUGH A VENTED HYDROTURBINE 75. Development

Food-Web Complexity in Guaymas Basin Hydrothermal Vents and Cold Seeps.

Directory of Open Access Journals (Sweden)

Marie Portail

Full Text Available In the Guaymas Basin, the presence of cold seeps and hydrothermal vents in close proximity, similar sedimentary settings and comparable depths offers a unique opportunity to assess and compare the functioning of these deep-sea chemosynthetic ecosystems. The food webs of five seep and four vent assemblages were studied using stable carbon and nitrogen isotope analyses. Although the two ecosystems shared similar potential basal sources, their food webs differed: seeps relied predominantly on methanotrophy and thiotrophy via the Calvin-Benson-Bassham (CBB cycle and vents on petroleum-derived organic matter and thiotrophy via the CBB and reductive tricarboxylic acid (rTCA cycles. In contrast to symbiotic species, the heterotrophic fauna exhibited high trophic flexibility among assemblages, suggesting weak trophic links to the metabolic diversity of chemosynthetic primary producers. At both ecosystems, food webs did not appear to be organised through predator-prey links but rather through weak trophic relationships among co-occurring species. Examples of trophic or spatial niche differentiation highlighted the importance of species-sorting processes within chemosynthetic ecosystems. Variability in food web structure, addressed through Bayesian metrics, revealed consistent trends across ecosystems. Food-web complexity significantly decreased with increasing methane concentrations, a common proxy for the intensity of seep and vent fluid fluxes. Although high fluid-fluxes have the potential to enhance primary productivity, they generate environmental constraints that may limit microbial diversity, colonisation of consumers and the structuring role of competitive interactions, leading to an overall reduction of food-web complexity and an increase in trophic redundancy. Heterogeneity provided by foundation species was identified as an additional structuring factor. According to their biological activities, foundation species may have the potential to

Adherence evaluation of vented chest seals in a swine skin model.

Science.gov (United States)

Arnaud, Françoise; Maudlin-Jeronimo, Eric; Higgins, Adam; Kheirabadi, Bijan; McCarron, Richard; Kennedy, Daniel; Housler, Greggory

2016-10-01

Perforation of the chest (open pneumothorax) with and without lung injury can cause air accumulation in the chest, positive intrapleural pressure and lead to tension pneumothorax if untreated. The performance of chest seals to prevent tension physiology depends partially on their ability to adhere to the skin and seal the chest wound. Novel non-occlusive vented chest seals were assessed for their adhesiveness on skin of live swine under normal and extreme environmental conditions to simulate austere battlefield conditions. Chest seals were applied on the back of the swine on skin that was soiled by various environmental contaminants to represent battlefield situations. A peeling (horizontal rim peeling) and detachment and breaching (vertical pulling) techniques were used to quantify the adhesive performance of vented chest seals. Among eight initially selected vented seals, five (Bolin, Russell, Fast breathe, Hyfin and SAM) were further down-selected based on their superior adherence scores at ambient temperatures. The adherence of these seals was then assessed after approximately 17h storage at extreme cold (-19.5°C) and hot (71.5°C) temperatures. Adherence scores for peeling (above 90%) and detachment scores (less than 25%) were comparable for four vented chest seals when tested at ambient temperature, except for the Bolin seal which had higher breaching. Under extreme storage temperatures, adherence peeling scores were comparable to those at ambient temperatures for four chest seals. Scores were significantly lower for the Bolin seal at extreme temperatures. This seal also had the highest detachment and breaching scores. In contrast, the Russell, Fast breathe, Hyfin and SAM seals showed similar ability to stay air tight without breaching after hot storage. No significant difference was found in skin adherence of the five vented chest seals at ambient temperature and the four seals (Russell, Fast breathe, Hyfin and SAM) maintained superior adherence even after

Open versus closed lateral internal anal sphincterotomy in the management of chronic anal fissures: A prospective randomized study

Directory of Open Access Journals (Sweden)

Vivek Gupta

2014-10-01

Conclusion: Closed lateral internal sphincterotomy is the treatment of choice for chronic fissures as it is effective, safe, less expensive, and associated with a lower rate of complications than the open sphincterotomy technique.

Hydrothermal vent fields discovered in the southern Gulf of California clarify role of habitat in augmenting regional diversity.

Science.gov (United States)

Goffredi, Shana K; Johnson, Shannon; Tunnicliffe, Verena; Caress, David; Clague, David; Escobar, Elva; Lundsten, Lonny; Paduan, Jennifer B; Rouse, Greg; Salcedo, Diana L; Soto, Luis A; Spelz-Madero, Ronald; Zierenberg, Robert; Vrijenhoek, Robert

2017-07-26

Hydrothermal vent communities are distributed along mid-ocean spreading ridges as isolated patches. While distance is a key factor influencing connectivity among sites, habitat characteristics are also critical. The Pescadero Basin (PB) and Alarcón Rise (AR) vent fields, recently discovered in the southern Gulf of California, are bounded by previously known vent localities (e.g. Guaymas Basin and 21° N East Pacific Rise); yet, the newly discovered vents differ markedly in substrata and vent fluid attributes. Out of 116 macrofaunal species observed or collected, only three species are shared among all four vent fields, while 73 occur at only one locality. Foundation species at basalt-hosted sulfide chimneys on the AR differ from the functional equivalents inhabiting sediment-hosted carbonate chimneys in the PB, only 75 km away. The dominant species of symbiont-hosting tubeworms and clams, and peripheral suspension-feeding taxa, differ between the sites. Notably, the PB vents host a limited and specialized fauna in which 17 of 26 species are unknown at other regional vents and many are new species. Rare sightings and captured larvae of the 'missing' species revealed that dispersal limitation is not responsible for differences in community composition at the neighbouring vent localities. Instead, larval recruitment-limiting habitat suitability probably favours species differentially. As scenarios develop to design conservation strategies around mining of seafloor sulfide deposits, these results illustrate that models encompassing habitat characteristics are needed to predict metacommunity structure. © 2017 The Authors.

The dry filter method for passive filtered venting of the containment

International Nuclear Information System (INIS)

Freis, Daniel; Tietsch, Wolfgang; Obenland, Ralf; Kroes, Bert; Martinsteg, Hans

2013-01-01

Filtered Venting is a mitigative emergency measure to protect the containment from pressure failure in case of a severe accident. Filtered vent systems which are based on the Dry Filter Method (DFM) are proven technology, work completely passive, meet all functional requirements and show excellent performance with respect to filter efficiency. With such a system the release of radioactive fission products to the environment can be effectively minimized. Short and long term land contaminations can be avoided. (orig.)

Geomicrobiology of sublacustrine thermal vents in Yellowstone Lake: Geochemical controls on microbial community structure and function

Directory of Open Access Journals (Sweden)

William P. Inskeep

2015-10-01

Full Text Available Yellowstone Lake (Yellowstone National Park, WY, USA is a large high-altitude (2200 m, fresh-water lake, which straddles an extensive caldera and is the center of significant geothermal activity. The primary goal of this interdisciplinary study was to evaluate the microbial populations inhabiting thermal vent communities in Yellowstone Lake (Yellowstone Lake using 16S rRNA gene and random metagenome sequencing, and to determine how geochemical attributes of vent waters influence the distribution of specific microorganisms and their metabolic potential. Thermal vent waters and associated microbial biomass were sampled during two field seasons (2007 - 2008 using a remotely operated vehicle (ROV. Sublacustrine thermal vent waters (circa 50 - 90 oC contained elevated concentrations of numerous constituents associated with geothermal activity including dissolved hydrogen, sulfide, methane and carbon dioxide. Microorganisms associated with sulfur-rich filamentous ‘streamer’ communities of Inflated Plain and West Thumb (pH range 5 - 6 were dominated by bacteria from the Aquificales, but also contained thermophilic archaea from the Crenarchaeota and Euryarchaeota. Novel groups of methanogens and members of the Korarchaeota were observed in vents from West Thumb and Elliot’s Crater (pH 5 - 6. Conversely, metagenome sequence from Mary Bay vent sediments did not yield large assemblies, and contained diverse thermophilic and nonthermophilic bacterial relatives. Analysis of functional genes associated with the major vent populations indicated a direct linkage to high concentrations of carbon dioxide, reduced sulfur (sulfide and/or elemental S, hydrogen and methane in the deep thermal ecosystems. Our observations show that sublacustrine thermal vents in Yellowstone Lake support novel thermophilic communities, which contain microorganisms with functional attributes not found to date in terrestrial geothermal systems of YNP.

Prevalence of Dental Caries and Fissure Sealants in a Portuguese Sample of Adolescents

Science.gov (United States)

Veiga, Nélio J.; Pereira, Carlos M.; Ferreira, Paula C.; Correia, Ilidio J.

2015-01-01

Introduction The aims of this study were to assess the prevalence of dental caries and the DMFT index, as well as the distribution pattern of pit and fissure sealants on permanent teeth in a Portuguese sample of adolescents, and to assess whether the existing usage of sealants and socio-demographic factors are correlated to caries prevalence on the examined sample. Materials and Methods A cross-sectional study was designed with a sample of 447 adolescents aged 12 to 18 years old, attending a public school in Sátão, Portugal. A self-administered questionnaire with questions about oral health behaviours and socio-economic status was answered by adolescents in the classroom. Clinical examination of oral health status and assessment of fissure sealants were accomplished by only one trained member of the research team. Results We obtained a DMFT index of 3.32 (2.92), which indicates a moderate level of prevalence of dental caries. When considering a DMFT = 0, we found significant statistical differences between the parents´ level of education (≤ 4th grade = 26.3 vs 5th–12th grade = 18.8 vs Portuguese adolescents. The establishment of a more targeted preventive program with better and more effective oral health education is essential, having into account socio-demographic aspects. PMID:25803849

Seafloor geomorphic manifestations of gas venting and shallow subbottom gas hydrate occurrences

Science.gov (United States)

Paull, C K; Caress, D W; Thomas, Hans; Lundsten, Eve M.; Anderson, Kayce; Gwiazda, Roberto; Riedel, M; McGann, Mary; Herguera, J C

2015-01-01

High-resolution multibeam bathymetry data collected with an autonomous underwater vehicle (AUV) complemented by compressed high-intensity radar pulse (Chirp) profiles and remotely operated vehicle (ROV) observations and sediment sampling reveal a distinctive rough topography associated with seafloor gas venting and/or near-subsurface gas hydrate accumulations. The surveys provide 1 m bathymetric grids of deep-water gas venting sites along the best-known gas venting areas along the Pacific margin of North America, which is an unprecedented level of resolution. Patches of conspicuously rough seafloor that are tens of meters to hundreds of meters across and occur on larger seafloor topographic highs characterize seepage areas. Some patches are composed of multiple depressions that range from 1 to 100 m in diameter and are commonly up to 10 m deeper than the adjacent seafloor. Elevated mounds with relief of >10 m and fractured surfaces suggest that seafloor expansion also occurs. Ground truth observations show that these areas contain broken pavements of methane-derived authigenic carbonates with intervening topographic lows. Patterns seen in Chirp profiles, ROV observations, and core data suggest that the rough topography is produced by a combination of diagenetic alteration, focused erosion, and inflation of the seafloor. This characteristic texture allows previously unknown gas venting areas to be identified within these surveys. A conceptual model for the evolution of these features suggests that these morphologies develop slowly over protracted periods of slow seepage and shows the impact of gas venting and gas hydrate development on the seafloor morphology.

10 CFR 50.46a - Acceptance criteria for reactor coolant system venting systems.

Science.gov (United States)

2010-01-01

... 10 Energy 1 2010-01-01 2010-01-01 false Acceptance criteria for reactor coolant system venting systems. 50.46a Section 50.46a Energy NUCLEAR REGULATORY COMMISSION DOMESTIC LICENSING OF PRODUCTION AND... function of these systems. High point vents are not required for the tubes in U-tube steam generators...

Loki's Castle: Discovery and geology of a black smoker vent field at the Arctic Mid-Ocean Ridge

Science.gov (United States)

Pedersen, R.; Thorseth, I. H.; Lilley, M. D.; Barriga, F. J.; Früh-Green, G.; Nakamura, K.

2010-12-01

Previous attempts to locate hydrothermal vent fields and unravel the nature of venting at the ultraslow spreading and magma starved parts of the Arctic Mid Ocean Ridge (AMOR) have been unsuccessful. A black smoker vent field was eventually discovered at the Mohns-Knipovich bend at 73.5°N in 2008, and the field was revisited in 2009 and 2010. The Loki’s Castle vent field is located on the crest of an axial volcanic ridge that is bordered by a tectonic terrain dominated by core complexes to the NW, and a ridge flank that is buried by sediments from the Bear Island Fan to the SE. Fluid compositions are anomalous to other basalt-hosted fields and indicate interactions with sediments at depths. The vent field is associated with an unusually large hydrothermal deposit, which documents that extensive venting occurs at ultraslow spreading ridges despite the strongly reduced magmatic heat budget. ROV surveys have shown that venting occurs in two areas separated by around 100 m. Micro-bathymetry acquired by a Hugin AUV documents that two 20-30 tall mounds that coalesce at the base have developed around the vent sites. The micro-bathymetry also shows that the venting is located above two normal faults that define the NW margin of a rift that runs along the crest of the volcano. The black smoker fluids reach 317 °C, with an end-member SiO2 content of 16 mmol/kg. End-member chlorinity is around 85% of seawater suggesting that the fluids have phase-separated at depth. The fluid compositions indicate that the rock-water reactions occur around 2 km below the seafloor. The crustal thickness is estimated to be 4 +/- 0.5 km in the area. Whereas the depth of the reaction zone is comparable with faster spreading ridges, the fraction of crust cooled convectively by hydrothermal circulation is two times that of vent fields at ridges with normal crustal thickness.

Calculation and analysis of hydrogen volume concentrations in the vent pipe rigid proposed for NPP-L V

International Nuclear Information System (INIS)

Gomez T, A. M.; Xolocostli M, V.; Lopez M, R.; Filio L, C.; Royl, P.

2014-10-01

In 2012 was modeled of primary and secondary container of the nuclear power plant of Laguna Verde (NPP-L V) for the CFD Gas-Flow code. These models were used to calculate hydrogen volume concentrations run release the reactor building in case of a severe accident. The results showed that the venting would produce detonation conditions in the venting level (level 33) and flammability at ground level of reload. One of the solutions to avoid reaching critical concentrations (flammable or detonable) inside the reactor building and thus safeguard the contentions is to make a rigid venting. The rigid vent is a pipe connected to the primary container could go to the level 33 of the secondary container and style fireplace climb to the top of the reactor building. The analysis of hydrogen transport inside the vent pipe can be influenced by various environmental criteria and factors vent, so a logical consequence of the 2012 analysis is the analysis of the gases transport within said pipe to define vent ideal conditions. For these evaluations the vent pipe was modeled with a fine mesh of 32 radial interior nodes and a coarse mesh of 4 radial interior nodes. With three-dimensional models were realized calculations that allow observing the influence of heat transfer in the long term, i.e. a complete analysis of exhaust (approx. 700 seconds). However, the most interesting results focus on the first milliseconds, when the H 2 coming from the atmosphere of the primary container faces the air in the vent pipe. These first milliseconds besides allowing evaluating the detonation criteria in great detail in the different tubular sections similarly allow evaluating the pressure wave that occurs in the pipe and that at some point slows to the fluid on the last tubular section and could produce a detonation inside the pipe. Results are presented for venting fixed conditions, showing possible detonations into the pipe. (Author)

Community Structure Comparisons of Hydrothermal Vent Microbial Mats Along the Mariana Arc and Back-arc

Science.gov (United States)

Hager, K. W.; Fullerton, H.; Moyer, C. L.

2015-12-01

Hydrothermal vents along the Mariana Arc and back-arc represent a hotspot of microbial diversity that has not yet been fully recognized. The Mariana Arc and back-arc contain hydrothermal vents with varied vent effluent chemistry and temperature, which translates to diverse community composition. We have focused on iron-rich sites where the dominant primary producers are iron oxidizing bacteria. Because microbes from these environments have proven elusive in culturing efforts, we performed culture independent analysis among different microbial communities found at these hydrothermal vents. Terminal-restriction fragment length polymorphism (T-RFLP) and Illumina sequencing of small subunit ribosomal gene amplicons were used to characterize community members and identify samples for shotgun metagenomics. Used in combination, these methods will better elucidate the composition and characteristics of the bacterial communities at these hydrothermal vent systems. The overarching goal of this study is to evaluate and compare taxonomic and metabolic diversity among different communities of microbial mats. We compared communities collected on a fine scale to analyze the bacterial community based on gross mat morphology, geography, and nearby vent effluent chemistry. Taxa richness and evenness are compared with rarefaction curves to visualize diversity. As well as providing a survey of diversity this study also presents a juxtaposition of three methods in which ribosomal small subunit diversity is compared with T-RFLP, next generation amplicon sequencing, and metagenomic shotgun sequencing.

40 CFR Table 4 to Subpart Vvvvvv... - Emission Limits and Compliance Requirements for Metal HAP Process Vents

Science.gov (United States)

2010-07-01

... Requirements for Metal HAP Process Vents 4 Table 4 to Subpart VVVVVV of Part 63 Protection of Environment... of Part 63—Emission Limits and Compliance Requirements for Metal HAP Process Vents As required in § 63.11496(f), you must comply with the requirements for metal HAP process vents as shown in the...

Kolanut (Cola Nitida Vent Schott of Endlicher)

African Journals Online (AJOL)

Kolanut (Cola Nitida Vent Schott of Endlicher). S.O. Agbeniyi, Otuonye, H.A. andAR. Adedeji Cocoa Research Institute of Nigeria. Abstract. The mycoflora associated with processing stages of kolanut post-harvest were evaluated at the Cocoa. Research Institute of Nigeria, Ibadan Nigeria. Several samples of healthy and ...

Tornado protection by venting

International Nuclear Information System (INIS)

Cavanagh, C.A.

1987-01-01

The purpose of this paper is to demonstrate the ability to protect a modern nuclear power plant from the effects of a tornado by the use of a system of venting in all safety-related structures outside of the containment. The paper demonstrates this by presenting a method of analysis and of equipment selection that fully complies with the intent and the letter of applicable federal regulatory guides. A report of an actual tornado in the City of Kalamazoo, Michigan, suggests that the concept of sealing a plant during a tornado may not always be applicable

Reversible Venting Stitch for Fenestrating Valve-less Glaucoma Shunts.

Science.gov (United States)

Akil, Handan; Vu, Priscilla Q; Nguyen, Anhtuan H; Nugent, Alexander; Chopra, Vikas; Francis, Brian A; Tan, James C

2017-12-01

The purpose of this is to describe a venting stitch modification for valveless glaucoma aqueous shunts and characterize early postoperative intraocular pressure (IOP) and glaucoma medication use following the modification. Retrospective chart review of 61 sequential patients undergoing Baerveldt glaucoma implant (BGI)-350 implantation at the Doheny Eye Institute. Twenty-four patients received a glaucoma shunt with venting stitch modification (modified BGI) and 37 patients received an unmodified shunt (BGI-only). IOP, number of glaucoma medications, and number of hypotony cases (intraocular pressure ≤5 mm Hg) were compared between the groups. T-tests were used for statistical analysis. At postoperative-day 1, mean IOP was significantly lower compared with preoperatively in the modified BGI group (14 mm Hg; reduced by 51%; P<0.0001) but not the BGI-only group (27 mm Hg; P=0.06). IOP difference between groups persisted till immediately before tube opening (P=0.005) and fewer IOP-lowering medications needed in the modified BGI group (P<0.0001). One case (4.2%) of postoperative hypotony was encountered with BGI modification, which resolved after the stitch was removed in clinic. The venting stitch valveless shunt modification allows for effective, reliable, and safe control of early postoperative IOP.

A helium venting model for a SSC half cell

International Nuclear Information System (INIS)

Carcagno, R.H.; McAshan, M.S.; Schiesser, W.E.

1991-01-01

When a Superconducting Super Collider (SSC) dipole magnet quenches, the quench protection system will intentionally quench other magnets in the half cell. The result is that the stored energy of all of these quenched magnets will be absorbed equally among them. These simultaneous quenches produce heat, which diffuses from the magnet coils to the main helium (He) coolant channels and thereby eventually causes an increase in the He pressure. When the quench is detected, vent valves open to minimize the He pressure increase and thus prevent damage to the magnets. The performance of the He venting system has been modeled and simulated to establish whether the venting will take place as required. The model consists of partial differential equation energy balances written radially for the magnet coils, collar, and yoke; and ordinary differential equations of energy and mass balance written for the He in the magnets and relief header. The basic algorithm is the numerical method of lines, with finite difference approximation of the spatial derivatives, and time integration by LSODES. Simulation results are presented for an SSC half cell of the Accelerator Systems String Test (ASST) facility. The results are also compared with recent string quench measurements performed at the Fermilab String Test Facility

[Evaluation of the effect of one-step self etching adhesives applied in pit and fissure sealing].

Science.gov (United States)

Su, Hong-Ru; Xu, Pei-Cheng; Qian, Wen-Hao

2016-06-01

To observe the effect of three one-step self etching adhesive systems used in fit and fissure sealant and explore the feasibility of application in caries prevention in school. Seven hundred and twenty completely erupted mandibular first molars in 360 children aged 7 to 9 years old were chosen. The split-mouth design was used to select one side as the experimental group, divided into A1(Easy One Adper), B1(Adper Easy One), and C1(iBond SE).The contra lateral teeth served as A2,B2 and C2 groups (phosphoric acid). The retention and caries status were regularly reviewed .The clinical effect of the two groups was compared using SPSS19.0 software package for Chi - square test. At 3 and 6 months, pit and fissure sealant retention rate in A1 and A2, B1 and B2,C1 and C2 group had no significant difference. At 12 months, sealant retention in A1 and B1 group was significantly lower than A2 and B2 group (P0.05). At 24 months, sealant retention rate in A1, B1 and C1 group was significantly lower than A2, B2 and C2 group (P0.05). The clinical anticariogenic effect of three kinds of one-step etching adhesives and phosphoric acid etching sealant was similar .One-step self etching adhesive system was recommended for pit and fissure sealant to improve the students' oral health. The long-term retention rate of one-step self etching adhesive system was lower than the phosphoric acid method to long term observation is needed.

Bayesian optimization analysis of containment-venting operation in a boiling water reactor severe accident

International Nuclear Information System (INIS)

Zheng, Xiaoyu; Ishikawa, Jun; Sugiyama, Tomoyuki; Maryyama, Yu

2017-01-01

Containment venting is one of several essential measures to protect the integrity of the final barrier of a nuclear reactor during severe accidents, by which the uncontrollable release of fission products can be avoided. The authors seek to develop an optimization approach to venting operations, from a simulation-based perspective, using an integrated severe accident code, THALES2/KICHE. The effectiveness of the containment-venting strategies needs to be verified via numerical simulations based on various settings of the venting conditions. The number of iterations, however, needs to be controlled to avoid cumbersome computational burden of integrated codes. Bayesian optimization is an efficient global optimization approach. By using a Gaussian process regression, a surrogate model of the “black-box” code is constructed. It can be updated simultaneously whenever new simulation results are acquired. With predictions via the surrogate model, upcoming locations of the most probable optimum can be revealed. The sampling procedure is adaptive. Compared with the case of pure random searches, the number of code queries is largely reduced for the optimum finding. One typical severe accident scenario of a boiling water reactor is chosen as an example. The research demonstrates the applicability of the Bayesian optimization approach to the design and establishment of containment-venting strategies during severe accidents

Bayesian optimization analysis of containment-venting operation in a boiling water reactor severe accident

Energy Technology Data Exchange (ETDEWEB)

Zheng, Xiaoyu; Ishikawa, Jun; Sugiyama, Tomoyuki; Maryyama, Yu [Nuclear Safety Research Center, Japan Atomic Energy Agency, Ibaraki (Japan)

2017-03-15

Containment venting is one of several essential measures to protect the integrity of the final barrier of a nuclear reactor during severe accidents, by which the uncontrollable release of fission products can be avoided. The authors seek to develop an optimization approach to venting operations, from a simulation-based perspective, using an integrated severe accident code, THALES2/KICHE. The effectiveness of the containment-venting strategies needs to be verified via numerical simulations based on various settings of the venting conditions. The number of iterations, however, needs to be controlled to avoid cumbersome computational burden of integrated codes. Bayesian optimization is an efficient global optimization approach. By using a Gaussian process regression, a surrogate model of the “black-box” code is constructed. It can be updated simultaneously whenever new simulation results are acquired. With predictions via the surrogate model, upcoming locations of the most probable optimum can be revealed. The sampling procedure is adaptive. Compared with the case of pure random searches, the number of code queries is largely reduced for the optimum finding. One typical severe accident scenario of a boiling water reactor is chosen as an example. The research demonstrates the applicability of the Bayesian optimization approach to the design and establishment of containment-venting strategies during severe accidents.

Microbial communities and chemosynthesis in Yellowstone Lake sublacustrine hydrothermal vent waters

Directory of Open Access Journals (Sweden)

Tingting eYang

2011-06-01

Full Text Available Abstract. Five sublacustrine hydrothermal vent locations from 1-109 m water depth in Yellowstone Lake were surveyed by ribosomal RNA sequencing in relation to their chemical composition and dark CO2 fixation rates. They harbor distinct chemosynthetic bacterial communities, depending on temperature (16 - 110ºC and electron donor supply (H2S <1 - >100µM; NH3 <0.5 - >10µM. Members of the Aquificales, most closely affiliated with the genus Sulfurihydrogenibium, are the most frequently recovered bacterial 16S rRNA gene phylotypes in the hottest samples; the detection of these thermophilic sulfur-oxidizing autotrophs coincided with maximal dark CO2 fixation rates reaching near 9 µM C h-1 at temperatures of 50 to 60°C. Vents at lower temperatures yielded mostly phylotypes related to the mesophilic gammaproteobacterial sulfur oxidizer Thiovirga. In contrast, cool vent water with low chemosynthetic activity yielded predominantly phylotypes related to freshwater Actinobacterial clusters with a cosmopolitan distribution.

Fissure sealants in caries prevention:a practice-based study using survival analysis

OpenAIRE

Leskinen, K. (Kaja)

2010-01-01

Abstract The purpose of this study was to analyse the effectiveness and cost of fissure sealant treatment in preventing dental caries in children in a practice-based research network using survival analysis. The survival times of first permanent molars in children were analysed in three countries: in Finland (age cohorts 1970–1972 and 1980–1982), in Sweden (1980–1982) and in Greece (1980–1982), and additionally at two municipal health centres in Finland (age cohorts 1988–1990 in Kemi...

An abyssal mobilome: Viruses, plasmids and vesicles from deep-sea hydrothermal vents

OpenAIRE

Lossouarn, Julien; Dupont, Samuel; Gorlas, Aurore; Mercier, Coraline; Bienvenu, Nadege; Marguet, Evelyne; Forterre, Patrick; Geslin, Claire

2015-01-01

Mobile genetic elements (MGEs) such as viruses, plasmids, vesicles, gene transfer agents (GTAs), transposons and transpovirions, which collectively represent the mobilome, interact with cellular organisms from all three domains of life, including those thriving in the most extreme environments. While efforts have been made to better understand deep-sea vent microbial ecology, our knowledge of the mobilome associated with prokaryotes inhabiting deep-sea hydrothermal vents remains limited. Here...

Light at deep sea hydrothermal vents

Science.gov (United States)

Van Dover, Cindy Lee; Cann, J. R.; Cavanaugh, Colleen; Chamberlain, Steven; Delaney, John R.; Janecky, David; Imhoff, Johannes; Tyson, J. Anthony

We usually think of the bottom of the sea as a dark environment, lit only by flashes of bioluminescent light. Discovery of light associated with geothermal processes at deep sea hydrothermal vents forces us to qualify our textbook descriptions of the seafloor as a uniformly dark environment. While a very dim glow emitted from high temperature (350°) vents (black smokers) at mid-oceanic ridge spreading centers has been documented [Van Dover et al, 1988], the source of this light and its role, if any, in the evolution and adaptation of photobiochemical processes have yet to be determined. Preliminary studies indicate that thermal radiation alone may account for the “glow” ]Smith and Delaney, 1989] and that a novel photoreceptor in shrimp-colonizing black smoker chimneys may detect this “glow” [Van Dover et al., 1989; Pelli and Chamberlain, 1989]. A more controversial question, posed by C. L. Van Dover, J. R. Cann, and J. R. Delaney at the 1993 LITE Workshop at the Woods Hole Oceanographic Institution in Massachusetts, is whether there may be sufficient light of appropriate wavelengths to support geothermally driven photosynthesis by microorganisms.

Superior orbital fissure syndrome in herpes zoster ophthalmicus.

LENUS (Irish Health Repository)

Kirwan, R P

2012-02-01

AIM: To report a case of superior orbital fissure syndrome (SOFS) in a patient with herpes zoster ophthalmicus (HZO). MATERIALS AND METHODS: A case report. RESULTS: A 71-year-old male with HZO presented acutely to accident and emergency complaining of right vision loss, double vision and drowsiness. The right visual acuity was counting fingers. There was no relative afferent pupillary defect. He had interstitial keratitis, ptosis, proptosis and total ophthalmoplaegia. The signs indicated HZO complicated by SOFS. Brain imaging and lumbar puncture confirmed the diagnosis of varicella zoster encephalitis. Systemic acyclovir and prednisolone led to recovery of visual acuity and ocular motility in addition to resolution of his proptosis and ptosis. CONCLUSION: SOFS is a rare complication of herpes zoster infection. With the appropriate treatment and follow-up, patients may be reassured that recovery of their visual acuity and ocular motility will occur.

Exploring the Ecology of Deep-Sea Hydrothermal Vents in a Metacommunity Framework

Directory of Open Access Journals (Sweden)

Lauren S. Mullineaux

2018-02-01

Full Text Available Species inhabiting deep-sea hydrothermal vents are strongly influenced by the geological setting, as it provides the chemical-rich fluids supporting the food web, creates the patchwork of seafloor habitat, and generates catastrophic disturbances that can eradicate entire communities. The patches of vent habitat host a network of communities (a metacommunity connected by dispersal of planktonic larvae. The dynamics of the metacommunity are influenced not only by birth rates, death rates and interactions of populations at the local site, but also by regional influences on dispersal from different sites. The connections to other communities provide a mechanism for dynamics at a local site to affect features of the regional biota. In this paper, we explore the challenges and potential benefits of applying metacommunity theory to vent communities, with a particular focus on effects of disturbance. We synthesize field observations to inform models and identify data gaps that need to be addressed to answer key questions including: (1 what is the influence of the magnitude and rate of disturbance on ecological attributes, such as time to extinction or resilience in a metacommunity; (2 what interactions between local and regional processes control species diversity, and (3 which communities are “hot spots” of key ecological significance. We conclude by assessing our ability to evaluate resilience of vent metacommunities to human disturbance (e.g., deep-sea mining. Although the resilience of a few highly disturbed vent systems in the eastern Pacific has been quantified, these values cannot be generalized to remote locales in the western Pacific or mid Atlantic where disturbance rates are different and information on local controls is missing.

Physical simulation and theoretical evolution for ground fissures triggered by underground coal mining.

Science.gov (United States)

Yang, Jing-Hu; Yu, Xiang; Yang, Yi; Yang, Zeng-Qiang

2018-01-01

Underground coal mining activities are prone to cause movement and breakage in geological strata and also lead to mining subsidence and even ground fissures. Along the direction working panel advancing, ground fissures may occur in roof in front and/or behind working panel. However, the investigations of previous similarity tests in lab only emphasize on the region behind working panel. By improving strata material property in construction and mounting artificial pressure devices, two physical simulation tests were conducted and successfully investigated the simulated results. Then, the mechanical model of "cantilever beam and elastic foundation beam" was proposed to calculate the stress distribution and the crack initiation angle in overlying strata and it well explains the mechanisms of ground fissures generation and propagation. Results show that, the maximum internal force in roof always occurred in front of working panel. However, because the void space in gob due to excavation is large enough to cause the bend and rotation of roof strata, compare to the triaxially compressed region in front of working panel, the roof always broke off at some positions above gob since the stress concentration resulting from such bend and rotation of strata could easily reach the limit strength of strata rocks. Also, the length of cantilever beam changed dynamically as respect to the panel advancing and the breakage intervals. Thus, the breakage position where the internal force first reached the limit tensile strength is not fixed and there will be two different kinds of relative positions between the crack initiation point and the working panel. The crack initiation direction is always perpendicular to the internal force, and the crack propagation direction is affected by the initiation angle, overburden-separation degree and the position of the hydraulic shields. If there is no overburden-separation or less, the roofs will break off as a composite beam and the propagation

Physical simulation and theoretical evolution for ground fissures triggered by underground coal mining

Science.gov (United States)

Yu, Xiang; Yang, Yi; Yang, Zeng-Qiang

2018-01-01

Underground coal mining activities are prone to cause movement and breakage in geological strata and also lead to mining subsidence and even ground fissures. Along the direction working panel advancing, ground fissures may occur in roof in front and/or behind working panel. However, the investigations of previous similarity tests in lab only emphasize on the region behind working panel. By improving strata material property in construction and mounting artificial pressure devices, two physical simulation tests were conducted and successfully investigated the simulated results. Then, the mechanical model of “cantilever beam and elastic foundation beam” was proposed to calculate the stress distribution and the crack initiation angle in overlying strata and it well explains the mechanisms of ground fissures generation and propagation. Results show that, the maximum internal force in roof always occurred in front of working panel. However, because the void space in gob due to excavation is large enough to cause the bend and rotation of roof strata, compare to the triaxially compressed region in front of working panel, the roof always broke off at some positions above gob since the stress concentration resulting from such bend and rotation of strata could easily reach the limit strength of strata rocks. Also, the length of cantilever beam changed dynamically as respect to the panel advancing and the breakage intervals. Thus, the breakage position where the internal force first reached the limit tensile strength is not fixed and there will be two different kinds of relative positions between the crack initiation point and the working panel. The crack initiation direction is always perpendicular to the internal force, and the crack propagation direction is affected by the initiation angle, overburden-separation degree and the position of the hydraulic shields. If there is no overburden-separation or less, the roofs will break off as a composite beam and the

Zero Gravity Cryogenic Vent System Concepts for Upper Stages

Science.gov (United States)

Ravex, Alain; Flachbart, Robin; Holt, Barney

The capability to vent in zero gravity without resettling is a technology need that involves practically all uses of sub-critical cryogenics in space. Venting without resettling would extend cryogenic orbital transfer vehicle capabilities. However, the lack of definition regarding liquid/ullage orientation coupled with the somewhat random nature of the thermal stratification and resulting pressure rise rates, lead to significant technical challenges. Typically a zero gravity vent concept, termed a thermodynamic vent system (TVS), consists of a tank mixer to destratify the propellant, combined with a Joule-Thomson (J-T) valve to extract thermal energy from the propellant. Marshall Space Flight Center's (MSFC's) Multipurpose Hydrogen Test Bed (MHTB) was used to test both spray bar and axial jet TVS concepts. The axial jet system consists of a recirculation pump heat exchanger unit. The spray bar system consists of a recirculation pump, a parallel flow concentric tube, heat exchanger, and a spray bar positioned close to the longitudinal axis of the tank. The operation of both concepts is similar. In the mixing mode, the recirculation pump withdraws liquid from the tank and sprays it into the tank liquid, ullage, and exposed tank surfaces. When energy extraction is required, a small portion of the recirculated liquid is passed sequentially through the J-T expansion valve, the heat exchanger, and is vented overboard. The vented vapor cools the circulated bulk fluid, thereby removing thermal energy and reducing tank pressure. The pump operates alone, cycling on and off, to destratify the tank liquid and ullage until the liquid vapor pressure reaches the lower set point. At that point, the J-T valve begins to cycle on and off with the pump. Thus, for short duration missions, only the mixer may operate, thus minimizing or even eliminating boil-off losses. TVS performance testing demonstrated that the spray bar was effective in providing tank pressure control within a 6

Modelling of vented dust explosions – empirical foundation and prospects for future validation of CFD codes

OpenAIRE

Skjold, Trygve; Wingerden, Kees van; Hansen, Olav R.; Eckhoff, Rolf Kristian

2008-01-01

Presented at: HAZARDS XX, Manchester, 23–25 November 2008 Explosion venting is the most frequently used method for mitigating the effects from accidental dust explosions in the process industry. Optimal design of vent systems and credible execution of risk assessments in powder handling plants require practical and reliable ways of predicting the course and consequences of vented dust explosions. The main parameters of interest include flame propagation and pressure build-up ...

Metatranscriptomics reveal differences in in situ energy and nitrogen metabolism among hydrothermal vent snail symbionts.

Science.gov (United States)

Sanders, J G; Beinart, R A; Stewart, F J; Delong, E F; Girguis, P R

2013-08-01

Despite the ubiquity of chemoautotrophic symbioses at hydrothermal vents, our understanding of the influence of environmental chemistry on symbiont metabolism is limited. Transcriptomic analyses are useful for linking physiological poise to environmental conditions, but recovering samples from the deep sea is challenging, as the long recovery times can change expression profiles before preservation. Here, we present a novel, in situ RNA sampling and preservation device, which we used to compare the symbiont metatranscriptomes associated with Alviniconcha, a genus of vent snail, in which specific host-symbiont combinations are predictably distributed across a regional geochemical gradient. Metatranscriptomes of these symbionts reveal key differences in energy and nitrogen metabolism relating to both environmental chemistry (that is, the relative expression of genes) and symbiont phylogeny (that is, the specific pathways employed). Unexpectedly, dramatic differences in expression of transposases and flagellar genes suggest that different symbiont types may also have distinct life histories. These data further our understanding of these symbionts' metabolic capabilities and their expression in situ, and suggest an important role for symbionts in mediating their hosts' interaction with regional-scale differences in geochemistry.

Highly sensitive avoidance plays a key role in sensory adaptation to deep-sea hydrothermal vent environments.

Directory of Open Access Journals (Sweden)

Tetsuya Ogino

Full Text Available The environments around deep-sea hydrothermal vents are very harsh conditions for organisms due to the possibility of exposure to highly toxic compounds and extremely hot venting there. Despite such extreme environments, some indigenous species have thrived there. Alvinellid worms (Annelida are among the organisms best adapted to high-temperature and oxidatively stressful venting regions. Although intensive studies of the adaptation of these worms to the environments of hydrothermal vents have been made, little is known about the worms' sensory adaptation to the severe chemical conditions there. To examine the sensitivity of the vent-endemic worm Paralvinella hessleri to low pH and oxidative stress, we determined the concentration of acetic acid and hydrogen peroxide that induced avoidance behavior of this worm, and compared these concentrations to those obtained for related species inhabiting intertidal zones, Thelepus sp. The concentrations of the chemicals that induced avoidance behavior of P. hessleri were 10-100 times lower than those for Thelepus sp. To identify the receptors for these chemicals, chemical avoidance tests were performed with the addition of ruthenium red, a blocker of transient receptor potential (TRP channels. This treatment suppressed the chemical avoidance behavior of P. hessleri, which suggests that TRP channels are involved in the chemical avoidance behavior of this species. Our results revealed for the first time hypersensitive detection systems for acid and for oxidative stress in the vent-endemic worm P. hessleri, possibly mediated by TRP channels, suggesting that such sensory systems may have facilitated the adaptation of this organism to harsh vent environments.

Blast from pressurized carbon dioxide released into a vented atmospheric chamber

Science.gov (United States)

Hansen, P. M.; Gaathaug, A. V.; Bjerketvedt, D.; Vaagsaether, K.

2018-03-01

This study describes the blast from pressurized carbon dioxide (CO2) released from a high-pressure reservoir into an openly vented atmospheric chamber. Small-scale experiments with pure vapor and liquid/vapor mixtures were conducted and compared with simulations. A motivation was to investigate the effects of vent size and liquid content on the peak overpressure and impulse response in the atmospheric chamber. The comparison of vapor-phase CO2 test results with simulations showed good agreement. This numerical code described single-phase gas dynamics inside a closed chamber, but did not model any phase transitions. Hence, the simulations described a vapor-only test into an unvented chamber. Nevertheless, the simulations reproduced the incident shock wave, the shock reflections, and the jet release inside the atmospheric chamber. The rapid phase transition did not contribute to the initial shock strength in the current test geometry. The evaporation rate was too low to contribute to the measured peak overpressure that was in the range of 15-20 kPa. The simulation results produced a calculated peak overpressure of 12 kPa. The liquid tests showed a significantly higher impulse compared to tests with pure vapor. Reducing the vent opening from 0.1 to 0.01 m2 resulted in a slightly higher impulse calculated at 100 ms. The influence of the vent area on the calculated impulse was significant in the vapor-phase tests, but not so clear in the liquid/vapor mixture tests.

Preliminary Design of Molecular Sieve for Removing Organic Iodide in Containment Filtered Venting System

Energy Technology Data Exchange (ETDEWEB)

Park, Tong Kyu; Shin, So Eun; Lee, Byung Chul [Heungdeok IT Valley Bldg., Yongin (Korea, Republic of); Kim, Hong Hyun; Lee, Kyung Jun [Gemvax and KAEL Inc., Daejeon (Korea, Republic of)

2014-05-15

In this paper, to increase the DF for gaseous iodine species, especially organic iodide, molecular sieve filled by silver exchanged zeolites is proposed and designed preliminarily. Its aerodynamic analysis is also performed and presented. In order to increase the DF for gaseous organic iodide, deep-bed type molecular sieve was proposed and designed preliminarily. Total 1,620kg of silver exchanged zeolites were filled evenly in 10 beds of the molecular sieve. The safety factor in the case of 20m{sup 3}/s will be smaller than the counterpart of the standard case (6m{sup 3}/s). However, if the adsorption capacity of the zeolites is larger than 3.09mg/g when the residence time is 0.09 second, the designed molecular sieve can be used at 20m3/s of volumetric flow rate. The removal efficiency for organic iodide should be considered as well as economical aspects in the design of molecular sieve. In the event of nuclear power plant (NPP) severe accident, the nuclear reactor containment might suffer damage resulting from overpressure caused by decay heat. In order to prevent this containment damage, containment venting has been considered as one of effective methods. However, since vented gases contain radioactive fission products, they should be filtered to be released to environment. Generally, containment filtered venting system (CFVS) is installed on NPP to achieve this aim. Even though great amount of efforts have been devoted to developing the CFVS using various filtering methods, the decontaminant factor (DF) for radioactive gaseous iodide is still unsatisfactory while DFs for radioactive aerosols and elemental iodine are very high.

ITER vent filter conceptual study. Final report ITER Task S71 TD 70 (NID-9e) EU Task SEA 3-4

Energy Technology Data Exchange (ETDEWEB)

Blomquist, R; Johansson, Kjell; Natalizio, A; Nilsson, Lars; Shen, K; Sjoeberg, A

1995-02-01

The aim of this study is to investigate vent filter technologies that could be applied to ITER in accidental situations and to discuss how effective they could be in reducing accidental releases of gases, vapors and aerosols to the atmosphere. The study`s main contents are: A description of vent filter technologies as they are used for fission reactors; A review of appropriate tritium removal technologies. The vent filter part deals mainly with aerosol removal. The tritium part includes removal of both elemental and oxidized tritium from the vent flow. An important conclusion is that current fission reactor vent filter systems do not remove elemental tritium from the vent stream. A third part of the study is scoping thermal-hydraulic and aerosol transport analyses in order to find realistic vent flow rates and aerosol transport characteristics. Theses analyses, which are based on ITER design data assumed at the time of analysis, have been performed by means of the codes RELAP5 and CONTAIN. Release estimates are also included. Suggestions and recommendations are given regarding how to design a reliable vent filter system. Suggested vent systems include: Vent ducts from vacuum vessel and heat exchanger departments, a water pool for condensation of steam, and equipment for removal of aerosols, elemental tritium and oxidized tritium. 42 refs, 6 tabs, 34 figs.

ITER vent filter conceptual study. Final report ITER Task S71 TD 70 (NID-9e) EU Task SEA 3-4

International Nuclear Information System (INIS)

Blomquist, R.; Johansson, Kjell; Natalizio, A.; Nilsson, Lars; Shen, K.; Sjoeberg, A.

1995-02-01

The aim of this study is to investigate vent filter technologies that could be applied to ITER in accidental situations and to discuss how effective they could be in reducing accidental releases of gases, vapors and aerosols to the atmosphere. The study's main contents are: A description of vent filter technologies as they are used for fission reactors; A review of appropriate tritium removal technologies. The vent filter part deals mainly with aerosol removal. The tritium part includes removal of both elemental and oxidized tritium from the vent flow. An important conclusion is that current fission reactor vent filter systems do not remove elemental tritium from the vent stream. A third part of the study is scoping thermal-hydraulic and aerosol transport analyses in order to find realistic vent flow rates and aerosol transport characteristics. Theses analyses, which are based on ITER design data assumed at the time of analysis, have been performed by means of the codes RELAP5 and CONTAIN. Release estimates are also included. Suggestions and recommendations are given regarding how to design a reliable vent filter system. Suggested vent systems include: Vent ducts from vacuum vessel and heat exchanger departments, a water pool for condensation of steam, and equipment for removal of aerosols, elemental tritium and oxidized tritium. 42 refs, 6 tabs, 34 figs

The invasive Red-vented bulbul (Pycnonotus cafer) outcompetes native birds in a tropical biodiversity hotspot.

Science.gov (United States)

Thibault, Martin; Vidal, Eric; Potter, Murray Alan; Sanchez, Thierry; Brescia, Fabrice

2018-01-01

Invasive alien species are a major cause of biodiversity loss globally, but especially on islands where high species richness and levels of endemism accentuate their impacts. The Red vented bulbul (Pycnonotus cafer), a tropical passerine bird that has been introduced widely across locations of high conservation value, is considered an extreme pest. It is currently expanding its range in New Caledonia, one of the world's biodiversity hotspots. Decisive recommendations on management strategies are required urgently to inform local managers and policy makers, but they should be based on quantitative local evidence, not just on expert opinion. The Red-vented bulbul is widely blamed for its impacts on biodiversity, especially through competition. We used data from 2,472 point counts to explore the abundance relationships between the Red-vented bulbul and 14 other species of bird. Our results revealed a negative relationship between the occurrence of the bulbul and the mean abundance of nine species, all native (or endemic, n = 3) to the New Caledonia archipelago. In contrast, the abundance of other introduced species such as Acridotheres tristis (Common myna), Passer domesticus (House sparrow) and Spilopelia chinensis (Spotted dove) were not affected by the Red-vented bulbul. Moreover, temporal trends in the abundance of impacted species suggest that the Red-vented bulbul may cause niche contractions rather than mortality for native species in man-modified habitats. Monitoring and control of the Red-vented bulbul is recommended to prevent on-going impacts on native bird communities throughout New Caledonia, and its impact on native bird communities elsewhere should be quantified.

The invasive Red-vented bulbul (Pycnonotus cafer outcompetes native birds in a tropical biodiversity hotspot.

Directory of Open Access Journals (Sweden)

Martin Thibault

Full Text Available Invasive alien species are a major cause of biodiversity loss globally, but especially on islands where high species richness and levels of endemism accentuate their impacts. The Red vented bulbul (Pycnonotus cafer, a tropical passerine bird that has been introduced widely across locations of high conservation value, is considered an extreme pest. It is currently expanding its range in New Caledonia, one of the world's biodiversity hotspots. Decisive recommendations on management strategies are required urgently to inform local managers and policy makers, but they should be based on quantitative local evidence, not just on expert opinion. The Red-vented bulbul is widely blamed for its impacts on biodiversity, especially through competition. We used data from 2,472 point counts to explore the abundance relationships between the Red-vented bulbul and 14 other species of bird. Our results revealed a negative relationship between the occurrence of the bulbul and the mean abundance of nine species, all native (or endemic, n = 3 to the New Caledonia archipelago. In contrast, the abundance of other introduced species such as Acridotheres tristis (Common myna, Passer domesticus (House sparrow and Spilopelia chinensis (Spotted dove were not affected by the Red-vented bulbul. Moreover, temporal trends in the abundance of impacted species suggest that the Red-vented bulbul may cause niche contractions rather than mortality for native species in man-modified habitats. Monitoring and control of the Red-vented bulbul is recommended to prevent on-going impacts on native bird communities throughout New Caledonia, and its impact on native bird communities elsewhere should be quantified.

Spatial and Temporal Population Genetics at Deep-Sea Hydrothermal Vents Along the East Pacific Rise and Galapagos Rift

Science.gov (United States)

2008-09-01

frequent physical disturbance. Earval dispersal among disjunct vent sites facilitates the persistence of sessile invertebrate species in these...among disjunct vent sites facilitates the persistence of sessile invertebrate species in these geologically and chemically dynamic habitats despite...the reproductive biology of the hydrothermal vent tube worm Riftia pachyptila. Marine Ecology Progress Series, 52, 89-94. Chevaldonne P, Jollivet D

The effects of venting and decompression on Yellow Tang (Zebrasoma flavescens in the marine ornamental aquarium fish trade

Directory of Open Access Journals (Sweden)

Emily S. Munday

2015-02-01

Full Text Available Each year, over 45 countries export 30 million fish from coral reefs as part of the global marine ornamental aquarium trade. This catch volume is partly influenced by collection methods that cause mortality. Barotrauma in fish resulting from forced ascent from depth can contribute to post-collection mortality. However, implementing decompression stops during ascent can prevent barotrauma. Conversely, venting (puncturing the swim bladder to release expanded internal gas following ascent can mitigate some signs of barotrauma like positive buoyancy. Here, we evaluate how decompression and venting affect stress and mortality in the Yellow Tang (Zebrasoma flavescens. We examined the effects of three ascent treatments, each with decompression stops of varying frequency and duration, coupled with or without venting, on sublethal effects and mortality using histology and serum cortisol measurements. In fish subjected to ascent without decompression stops or venting, a mean post-collection mortality of 6.2% occurred within 24 h of capture. Common collection methods in the fishery, ascent without decompression stops coupled with venting, or one long decompression stop coupled with venting, resulted in no mortality. Histopathologic examination of heart, liver, head kidney, and swim bladder tissues in fish 0d and 21d post-collection revealed no significant barotrauma- or venting-related lesions in any treatment group. Ascent without decompression stops resulted in significantly higher serum cortisol than ascent with many stops, while venting alone did not affect cortisol. Future work should examine links in the supply chain following collection to determine if further handling and transport stressors affect survivorship and sublethal effects.

Solution gas flaring and venting at Alberta primary crude bitumen operations

Energy Technology Data Exchange (ETDEWEB)

Ruff, C. [Alberta Energy and Utilities Board, Calgary, AB (Canada)

2005-11-01

The Alberta Energy and Utilities Board is mandated by the Government of Alberta to ensure fair, responsible development and delivery of energy resources and utilities services in Alberta while maintaining the best public interest. One of the agencies' priorities is the reduction of solution gas flaring and venting. The performance of solution gas flaring and venting in Alberta and best practices respecting solution gas conservation are discussed. Data was presented on solution gas production, solution gas conserved, and solution gas conservation efficiency. The paper described best practices solutions such as increased gas to oil (GOR) test frequency; predetermination of economic gas conservation; collaboration with county gas utilities; and utilization of portable and scalable gas compression. The paper also presents a discussion of the Clean Air Strategic Alliance (CASA), a non-profit multistakeholder that recommended enhancements to Guide 60. Requirements discussed include the requirement to conserve solution gas at certain sites exceeding established flare and vent volumes, gas conservation prebuild requirements, and enhanced economic evaluation process. 5 figs.

Development of a submerged gravel scrubber for containment venting applications: summary

International Nuclear Information System (INIS)

Hilliard, R.K.; McCormack, J.D.; Postma, A.K.

1981-01-01

Although hypothetical core disruptive accidents (HCDAs) are not design basis accidents for breeder reactor plants, extensive assessments of HCDA consequences have been made and design features for providing margins beyond the design base have been considered for future fast reactor plants. One feature proposed for increasing the safety margin is a containment vent and/or purge system which would mitigate the challenge to containment integrity resulting from excessive temperature and pressure or excessive hydrogen. A cleanup system would be required for removal of vented aerosols and condensible vapors to mitigate radiological consequences to the environment. A study is in progress at HEDL to select and develop a suitable air cleaning system for use in potential breeder reactor containment venting applications. A concept was conceived whereby the passiveness and high loading capacity of a water pool scrubber was combined with the high efficiency of a sand and gravel bed. It was termed a Submerged Gravel Scrubber (SGS). A schematic drawing of the concept is shown. The SGS consists of a bed of gravel (or other packing) submerged in a pool of water

Ilchulbong tuff cone, Jeju Island, Korea, revisited: A compound monogenetic volcano involving multiple magma batches, shifting vents, and discrete eruptive phases

Science.gov (United States)

Sohn, Y.; Brenna, M.; Smith, I. E.; Nemeth, K.; White, J. D.; Murtagh, R.; Jeon, Y.; Kwon, C.; Cronin, S. J.

2010-12-01

detecting potential shifts in eruption chemistry and vent location. It appears that if eruption breaks are short, successive magma batches follow the same path, whereas if pauses are greater than a critical period, conduit solidification will force vent migration for subsequent magma batches. This has important implications for examining the controls of vent migration at other monogenetic volcanoes and for emergency management planning during future similar types of eruptions.

Technical note: In vitro total gas and methane production measurements from closed or vented rumen batch culture systems.

Science.gov (United States)

Cattani, M; Tagliapietra, F; Maccarana, L; Hansen, H H; Bailoni, L; Schiavon, S

2014-03-01

This study compared measured gas production (GP) and computed CH4 production values provided by closed or vented bottles connected to gas collection bags. Two forages and 3 concentrates were incubated. Two incubations were conducted, where the 5 feeds were tested in 3 replicates in closed or vented bottles, plus 4 blanks, for a total of 64 bottles. Half of the bottles were not vented, and the others were vented at a fixed pressure (6.8 kPa) and gas was collected into one gas collection bag connected to each bottle. Each bottle (317 mL) was filled with 0.4000 ± 0.0010 g of feed sample and 60 mL of buffered rumen fluid (headspace volume = 257 mL) and incubated at 39.0°C for 24 h. At 24 h, gas samples were collected from the headspace of closed bottles or from headspace and bags of vented bottles and analyzed for CH4 concentration. Volumes of GP at 24 h were corrected for the gas dissolved in the fermentation fluid, according to Henry's law of gas solubility. Methane concentration (mL/100mL of GP) was measured and CH4 production (mL/g of incubated DM) was computed using corrected or uncorrected GP values. Data were analyzed for the effect of venting technique (T), feed (F), interaction between venting technique and feed (T × F), and incubation run as a random factor. Closed bottles provided lower uncorrected GP (-18%) compared with vented bottles, especially for concentrates. Correction for dissolved gas reduced but did not remove differences between techniques, and closed bottles (+25 mL of gas/g of incubated DM) had a greater magnitude of variation than did vented bottles (+1 mL of gas/g of incubated DM). Feeds differed in uncorrected and corrected GP, but the ranking was the same for the 2 techniques. The T × F interaction influenced uncorrected GP values, but this effect disappeared after correction. Closed bottles provided uncorrected CH4 concentrations 23% greater than that of vented bottles. Correction reduced but did not remove this difference. Methane

Request for approval, vented container annual release fraction

International Nuclear Information System (INIS)

HILL, J.S.

1999-01-01

In accordance with the approval conditions for Modification to the Central Waste Complex (CWC) Radioactive Air Emissions Notice of Construction (NOC). dated August 24,1998, a new release fraction has been developed for submittal to the Washington State Department of Health (WDOH). The proposed annual release fraction of 2.50 E-14 is proposed for use in future NOCs involving the storage and handling operations associated with vented containers on the Hanford Site. The proposed annual release fraction was the largest release fraction calculated from alpha measurements of the NucFil filters from 10 vented containers consisting of nine 55-gallon drums and one burial box with dimensions of 9.3 x 5.7 x 6.4 feet. An annual release fraction of 2.0 E-09 was used in the modification to the CWC radioactive air emissions NOC. This study confirmed that the release fraction used in the CWC radioactive air emissions NOC was conservative

Population genetic structure of Rufous-Vented Prinia (Prinia burnesii ...

African Journals Online (AJOL)

Administrator

2010-12-27

Dec 27, 2010 ... INTRODUCTION. The Rufous-vented Prinia is an endemic species of the. Indian subcontinent that is ..... considerations in listing subspecies under the U.S. Endangered. Species Act. Cons. Biol. 6: 1584-1594. Heukeshoven J ...

Shallow vent architecture of Puyehue Cordón-Caulle, as revealed by direct observation of explosive activity

Science.gov (United States)

Schipper, C. I.; Tuffen, H.; Castro, J. M.

2012-04-01

wall of the tephra cone were entrained upward into the main vertical portion of the plume. On Jan. 10, explosive activity was manifested as semi-continuous ash jetting from multiple point sources, as accommodated by a 10-20 m high incipient dome that had formed in the tephra cone. At any given time, up to 10 discrete point and linear sources of gas and ash discharge could be seen. These had variable directionality and produced plumes with spatially and temporally variable ash contents. Cycles of overpressure buildup and vent failure were still observed, but rarely produced significant bombs. Instead, failure was characterized by the simultaneous or staggered opening of many additional point discharge sources, often defining a dish-like structure around - but not disturbing - the incipient dome. During this lower-intensity activity, no defined gas-thrust region was maintained and the plume would often collapse to fill the tephra cone. Directed plumes that breached the cone continued to descend its outer slopes. Ongoing analysis of juvenile pyroclasts and video footage permits an assessment of overpressure buildup and release in the shallow conduit of the PCCVC, and an assessment of the complex shallow vent architecture. We address the ideas: (1) that to describe explosive ash jetting from a single "vent" is a gross oversimplification of what is actually a highly transient, multiple point-source vent complex subject to variations in permeability and rate/type of discharge; and (2) that gas and ash jetting and Vulcanian blasts play an important if not necessary role in generating degassed magma that erupts effusively (see Castro et al., this session).

Preoperational test report, vent building ventilation system

International Nuclear Information System (INIS)

Clifton, F.T.

1997-01-01

This represents a preoperational test report for Vent Building Ventilation Systems, Project W-030. Project W-030 provides a ventilation upgrade for the four Aging Waste Facility tanks. The system provides Heating, Ventilation, and Air Conditioning (HVAC) for the W-030 Ventilation Building. The tests verify correct system operation and correct indications displayed by the central Monitor and Control System

Analysis of radionuclide transport through fissured porous media with a perturbation method

Energy Technology Data Exchange (ETDEWEB)

Banat, M [JGC Corp., Tokyo (Japan)

1995-04-01

This paper presents a specific procedure for obtaining solutions for the transport of radionuclides in a fissured porous media. The concentration profiles are deduced for a wide range of Peclet numbers using a perturbation method with a multiscale of time. Results show clearly that because of an increase of longitudinal dispersion, the radionuclide moves faster with respect to the case of zero dispersion (i.e. an infinite Peclet number). The main purpose of this paper is to demonstrate the practical advantage of the present calculation method with respect to the classical numerical and analytical methods used for radionuclide transport. (author).

Comparison of dehumidification and heat and vent drying of hem-fir softwood

Energy Technology Data Exchange (ETDEWEB)

Mackay, J F.G.; Nielson, R W

1988-03-01

The objective of this project was to demonstrate the performance of dehumidifier kilns, compared to gas-fired, hot-air kilns in drying a commercial grade of softwood lumber. To accomplish this, drying tests were conducted with matched loads of lumber in a new test facility which was constructed to operate as a conventional heat and vent kiln or as a dehumidifier kiln. Comparisons were made of drying times, shrinkage and quality of dried product and total drying energy consumptions. Data from these tests were used in conjunction with capital, energy and other costs obtained from suppliers and operators of existing kilns to make economic comparisons between commercial-sized dehumidifier and heat and vent kilns. These comparisons were made on the basis of equivalent uniform annual costs. Dehumidification drying took about 20% longer and used about 50% of energy compared to heat and vent drying. Analysis of the test runs indicated that further improvements in the energy utilization efficiencies of dehumidifier kilns are feasible since one run indicated an energy consumption of only 36% of that in heat and vent drying. No differences in shrinkage or degrade were apparent. Economic comparisons for three sizes of kilns showed total drying costs by dehumidification to be less for a small-size kiln but more for medium- and large-size operations. Sensitivity analyses were performed to observe the effect of alternate energy prices, dehumidifier energy consumptions, dehumidifier drying times, building costs and degrade. 9 refs., 7 figs., 36 tabs.

Stratigraphic architecture of hydromagmatic volcanoes that have undergone vent migration: a review of Korean case studies

Science.gov (United States)

Sohn, Y.

2011-12-01

Recent studies show that the architecture of hydromagmatic volcanoes is far more complex than formerly expected. A number of external factors, such as paleohydrology and tectonics, in addition to magmatic processes are thought to play a role in controlling the overall characteristics and architecture of these volcanoes. One of the main consequences of these controls is the migration of the active vent during eruption. Case studies of hydromagmatic volcanoes in Korea show that those volcanoes that have undergone vent migration are characterized by superposition or juxtaposition of multiple rim deposits of partial tuff rings and/or tuff cones that have contrasting lithofacies characteristics, bed attitudes, and paleoflow directions. Various causes of vent migration are inferred from these volcanoes. Large-scale collapse of fragile substrate is interpreted to have caused vent migration in the Early Pleistocene volcanoes of Jeju Island, which were built upon still unconsolidated continental shelf sediments. Late Pleistocene to Holocene volcanoes, which were built upon a stack of rigid, shield-forming lava flows, lack features due to large-scale substrate collapse and have generally simple and circular morphologies either of a tuff ring or of a tuff cone. However, ~600 m shift of the eruptive center is inferred from one of these volcanoes (Ilchulbong tuff cone). The vent migration in this volcano is interpreted to have occurred because the eruption was sourced by multiple magma batches with significant eruptive pauses in between. The Yangpori diatreme in a Miocene terrestrial half-graben basin in SE Korea is interpreted to be a subsurface equivalent of a hydromagmatic volcano that has undergone vent migration. The vent migration here is inferred to have had both vertical and lateral components and have been caused by an abrupt tectonic activity near the basin margin. In all these cases, rimbeds or diatreme fills derived from different source vents are bounded by either

GASFLOW simulations for containment venting system of Emsland nuclear power plant

Energy Technology Data Exchange (ETDEWEB)

Xu, Zhanjie; Jordan, Thomas

2015-07-01

In a hypothetical core melt severe accident in nuclear power plants, a large amount of burnable gas, such as hydrogen and carbon monoxide, with certain amount of oxygen is released into the containment. In case of high containment pressure a filtered venting is designed as a mitigation measure. After aerosols and condensable portions of the gas mixture from the containment are purged, the remaining burnable gases flows into a chamber connected to horizontal venting pipes and further to a vertical stack, which is open to free atmosphere at the top. The main goal of the study is to investigate the chemical sensitivity of the burnable and potentially detonable gas mixture in the venting system by means of computational fluid dynamic computer simulations. Based on the calculations with different boundary conditions for different scenarios, it is concluded that the venting system has no risk of flame acceleration and detonation if the power supply of the ventilation fans can be maintained. In case of station blackout, the whole system has no risk of detonation if the scrubber - purging water pool - can get boiling in 10 minutes, owing to the heating effect resulted from the latent heat of the condensable gases into the water pool. It is because the injected steam from the boiling scrubber inerts the mixture of hydrogen, carbon monoxide plus oxygen, effectively and significantly. In this case, a gas mixture only in a very local region in the stack, as small as about 0.16 cubic meter, is in a risk of flame acceleration. It is in principle ignorable owing to the tiny volume and thus only a small amount of hydrogen and carbon monoxide.

Imprint of past environmental regimes on structure and succession of a deep-sea hydrothermal vent community.

Science.gov (United States)

Mullineaux, Lauren S; Micheli, Fiorenza; Peterson, Charles H; Lenihan, Hunter S; Markus, Nilauro

2009-08-01

Dramatic perturbations of ecological communities through rapid shifts in environmental regime do not always result in complete mortality of residents. Instead, legacy individuals may remain and influence the succession and composition of subsequent communities. We used a reciprocal transplant experiment to investigate whether a legacy effect is detectable in communities experiencing an abrupt increase or decrease in hydrothermal fluid flux at deep-sea vents. Vent habitats are characterized by strong gradients in productivity and physico-chemical stressors, both of which tend to increase with increasing vent fluid flux. In our experiments, many species survived transplantation from cool (water temperatures theory developed in the rocky intertidal that predicts the predominance of physical control at the high-stress end of an environmental gradient. Prediction of successional transitions in vents and other habitats experiencing regime shifts in which remnant species may survive must take into account the possible influence of historical effects.

Shuttle Gaseous Hydrogen Venting Risk from Flow Control Valve Failure

Science.gov (United States)

Drummond, J. Philip; Baurle, Robert A.; Gafney, Richard L.; Norris, Andrew T.; Pellett, Gerald L.; Rock, Kenneth E.

2009-01-01

This paper describes a series of studies to assess the potential risk associated with the failure of one of three gaseous hydrogen flow control valves in the orbiter's main propulsion system during the launch of Shuttle Endeavour (STS-126) in November 2008. The studies focused on critical issues associated with the possibility of combustion resulting from release of gaseous hydrogen from the external tank into the atmosphere during assent. The Shuttle Program currently assumes hydrogen venting from the external tank will result in a critical failure. The current effort was conducted to increase understanding of the risk associated with venting hydrogen given the flow control valve failure scenarios being considered in the Integrated In-Flight Anomaly Investigation being conducted by NASA.

Population subdivision of hydrothermal vent polychaete Alvinella pompejana across equatorial and Easter Microplate boundaries.

Science.gov (United States)

Jang, Sook-Jin; Park, Eunji; Lee, Won-Kyung; Johnson, Shannon B; Vrijenhoek, Robert C; Won, Yong-Jin

2016-10-28

The Equator and Easter Microplate regions of the eastern Pacific Ocean exhibit geomorphological and hydrological features that create barriers to dispersal for a number of animals associated with deep-sea hydrothermal vent habitats. This study examined effects of these boundaries on geographical subdivision of the vent polychaete Alvinella pompejana. DNA sequences from one mitochondrial and eleven nuclear genes were examined in samples collected from ten vent localities that comprise the species' known range from 23°N latitude on the East Pacific Rise to 38°S latitude on the Pacific Antarctic Ridge. Multi-locus genotypes inferred from these sequences clustered the individual worms into three metapopulation segments - the northern East Pacific Rise (NEPR), southern East Pacific Rise (SEPR), and northeastern Pacific Antarctic Ridge (PAR) - separated by the Equator and Easter Microplate boundaries. Genetic diversity estimators were negatively correlated with tectonic spreading rates. Application of the isolation-with-migration (IMa2) model provided information about divergence times and demographic parameters. The PAR and NEPR metapopulation segments were estimated to have split roughly 4.20 million years ago (Mya) (2.42-33.42 Mya, 95 % highest posterior density, (HPD)), followed by splitting of the SEPR and NEPR segments about 0.79 Mya (0.07-6.67 Mya, 95 % HPD). Estimates of gene flow between the neighboring regions were mostly low (2 Nm  SEPR > PAR. Highly effective dispersal capabilities allow A. pompejana to overcome the temporal instability and intermittent distribution of active hydrothermal vents in the eastern Pacific Ocean. Consequently, the species exhibits very high levels of genetic diversity compared with many co-distributed vent annelids and mollusks. Nonetheless, its levels of genetic diversity in partially isolated populations are inversely correlated with tectonic spreading rates. As for many other vent taxa, this pioneering colonizer is

Investigating pyroclast ejection dynamics using shock-tube experiments: temperature, grain size and vent geometry effects.

Science.gov (United States)

Cigala, V.; Kueppers, U.; Dingwell, D. B.

2015-12-01

Explosive volcanic eruptions eject large quantities of gas and particles into the atmosphere. The portion directly above the vent commonly shows characteristics of underexpanded jets. Understanding the factors that influence the initial pyroclast ejection dynamics is necessary in order to better assess the resulting near- and far-field hazards. Field observations are often insufficient for the characterization of volcanic explosions due to lack of safe access to such environments. Fortunately, their dynamics can be simulated in the laboratory where experiments are performed under controlled conditions. We ejected loose natural particles from a shock-tube while controlling temperature (25˚ and 500˚C), overpressure (15MPa), starting grain size distribution (1-2 mm, 0.5-1 mm and 0.125-0.250 mm), sample-to-vent distance and vent geometry. For each explosion we quantified the velocity of individual particles, the jet spreading angle and the production of fines. Further, we varied the setup to allow for different sample-to-gas ratios and deployed four different vent geometries: 1) cylindrical, 2) funnel with a flaring of 30˚, 3) funnel with a flaring of 15˚ and 4) nozzle. The results showed maximum particle velocities up to 296 m/s, gas spreading angles varying from 21˚ to 37˚ and particle spreading angles from 3˚ to 40˚. Moreover we observed dynamically evolving ejection characteristics and variations in the production of fines during the course of individual experiments. Our experiments mechanistically mimic the process of pyroclast ejection. Thus the capability for constraining the effects of input parameters (fragmentation conditions) and conduit/vent geometry on ballistic pyroclastic plumes has been clearly established. These data obtained in the presence of well-documented conduit and vent conditions, should greatly enhance our ability to numerically model explosive ejecta in nature.

Retention of a resin-based sealant and a glass ionomer used as a fissure sealant: A comparative clinical study

Directory of Open Access Journals (Sweden)

Subramaniam P

2008-09-01

Full Text Available Sealing occlusal pits and fissures with resin-based sealants is a proven method of preventing occlusal caries. Retention of the sealant is very essential for its efficiency. This study evaluated the retention of glass ionomer used as a fissure sealant when compared to a self-cure resin-based sealant. One hundred and seven children between the ages of 6-9 years, with all four newly erupted permanent first molars were selected. Two permanent first molars on one side of the mouth were sealed with Delton, a resin-based sealant, and the contralateral two permanent first molars were sealed with Fuji VII glass ionomer cement. Evaluation of sealant retention was performed at regular intervals over 12 months, using Simonsen′s criteria. At the end of the study period, the retention of the resin sealant was seen to be superior to that of the glass ionomer sealant.

Long-term outcomes of Botulinum toxin in the treatment of chronic anal fissure: 5 years of follow-up.

Science.gov (United States)

Barbeiro, Sandra; Atalaia-Martins, Catarina; Marcos, Pedro; Gonçalves, Cláudia; Canhoto, Manuela; Arroja, Bruno; Silva, Filipe; Cotrim, Isabel; Eliseu, Liliana; Santos, Antonieta; Vasconcelos, Helena

2017-03-01

Chronic anal fissure is a frequent and disabling disease, often affecting young adults. Botulinum toxin and lateral internal sphincterotomy are the main therapeutic options for refractory cases. Botulinum toxin is minimally invasive and safer compared with surgery, which carries a difficult post-operative recovery and fecal incontinence risk. The long-term efficacy of Botulinum toxin is not well known. The aim of this study was to evaluate the long-term efficacy and safety of Botulinum toxin in the treatment of chronic anal fissure. This was a retrospective study at a single center, including patients treated with Botulinum toxin from 2005 to 2010, followed over at least a period of 5 years. All patients were treated with injection of 25U of Botulinum toxin in the intersphincteric groove. The response was registered as complete, partial, refractory and relapse. Botulinum toxin was administered to 126 patients, 69.8% ( n  = 88) were followed over a period of 5 years. After 3 months, 46.6% ( n  = 41) had complete response, 23.9% ( n  = 21) had partial response and 29.5% ( n  = 26) were refractory. Relapse was observed in 1.2% ( n  = 1) at 6 months, 11.4% ( n  = 10) at 1 year, 2.3% ( n  = 2) at 3 years; no relapse at 5 years. The overall success rate was 64.8% at 5 years of follow-up. Botulinum toxin was well tolerated by all patients and there were no complications. The use of Botulinum toxin to treat patients with chronic anal fissure was safe and effective in long-term follow-up.

Vented fuel experiment for gas-cooled fast reactor application

International Nuclear Information System (INIS)

Longest, A.W.; Gat, U.; Conlin, J.A.; Campana, R.J.

1976-01-01

A pressure-equalized and vented fuel rod is being irradiated in an instrumented capsule designated GB-10 to approximately 100MWd/kg-heavy metal. The fuel is a sol-gel-derived 88 at.% uranium (approximately 9% 235 U) and 12 at.% plutonium oxide, and the cladding is 20% cold-worked 316 stainless steel. The capsule is being irradiated in the Oak Ridge Research Reactor (ORR) and has exceeded a burnup of 70MWd/kg. The fuel has been operated at linear power rates of 39 and 44kW/m, and peak outer cladding temperature of 565 and 630 0 C respectively. A similar fuel rod in a previous capsule (GB-9) was subjected to 48kW/m (685 0 C). Helium gas sweeps through any portion of the three regions of the fuel rod, namely: fuel, blanket, and charcoal trap. The charcoal trap is operated at about 300 0 C. An on-line Ge(Li) detector is used to analyse release rates of several gamma-emitting noble gas isotopes. Analyses are performed primarily on sweep gas flowing through the entire fuel rod, and for sweeps over the top of the charcoal trap. Sweep gas samples are analyzed for stable noble gas isotopes. Results in the form of ratios of release rate over birth rate (R/B) and venting rate over birth rate (V/B) are derived. R/B rates range from 10 -4 % to 30% while V/B ranges from 10 -6 % to 30%. Flow conductance in the capsule was monitored by recording the flow rate and pressure drop across the fuel rod and inlet sweep line. The flow conductance has been falling with increasing burnup, currently restricting the flow to about 20ml (s.t.p.)/min at a pressure difference of about 1.5MPa. Venting rates of the gaseous fission products as a function of gas pressure in the range 6.9 to 1.4MPa have also been measured. Planned future experiments include the monitoring of tritium release, venting and cladding permeation rates, and its molecular form. First measurements have been made. A simulated leak experiment will determine the mixture of fission gases as a function of flow rate and the most

Human reliability analysis for venting a BWR Mark I during a severe accident

International Nuclear Information System (INIS)

Nelson, W.R.; Blackman, H.S.

1986-01-01

A Human Reliability Analysis (HRA) was performed for the operator actions necessary to achieve containment venting for the Peach Bottom Atomic Power Station. This study was funded by the United States Nuclear Regulatory Commission (USNRC) and performed by the Idaho National Engineering Laboratory (INEL). The goal of the analysis was to estimate Human Error Probabilities (HEPs) to determine the likelihood that operators would fail to complete the venting process. The analysis was performed for two generic accident sequences: anticipated transient without scram (ATWS) and station blackout. Two major methods were used to estimate the HEPs: Technique for Human Error rate Prediction (THERP) and Success Likelihood Index Methodology (SLIM). For the ATWS scenarios analyzed, the calculated HEPs ranged from 0.23 to 0.35, depending on the number of vent paths that are required to reduce the containment pressure. It should be noted that the confidence bounds around these HEPs are large, However, even when considering the large confidence range, the failure probabilities are larger than what is typical for normal operator actions. For station blackout, the HEP is 1.0, resulting from the dangerous environmental conditions that are present, assuming that plant management would not deliberately expose personnel to a potentially fatal environment. These results are based on the analysis of draft procedures for containment venting. It is probable that careful revision of the procedures could reduce the human error probabilities

Modeling of the pollutant transport in fissured-porous media under consideration of colloids using the transport codes FRAME and COFRAME; Modellierung des Schadstofftransports in geklueftet-poroesen Medien unter Beruecksichtigung von Kolloiden mit den Transportprogrammen FRAME und COFRAME

Energy Technology Data Exchange (ETDEWEB)

Reiche, Tatiana; Noseck, Ulrich; Wolf, Jens Wilhelm

2014-05-15

For the long-term safety analysis of final nuclear waste repositories the transport of pollutants from the repository into the biosphere three mostly independent subsystems are considered: the near field, the geosphere and the biosphere. Normally rocks include fissures or other disturbances. Porous materials in the rock matrix have usually a high water content and acts as storage for pollutants due to sorption and diffusion processes. The aim of the project is the development of calculation modules for the code RepoTREND that simulate the pollutant transport in saturated fissured-porous media taking into account the effect of colloids. FRAME describes the pollutant dispersion in a fissured-porous medium and COFRAME the colloid influenced transport in a fissured-porous medium.

Caries progression in non-cavitated fissures after infiltrant application: a 3-year follow-up of a randomized controlled clinical trial

Directory of Open Access Journals (Sweden)

Camillo ANAUATE-NETTO

Full Text Available Abstract Objectives To evaluate the efficacy of a conservative treatment to prevent the progression of caries using an infiltrant on non-cavitated pit and fissures. Material and Methods This controlled clinical trial selected 23 volunteers with clinically and radiographically non-cavitated occlusal caries among patients presenting a “rather low” to “very high” caries risk. Eighty-six teeth were randomly divided into two experimental groups: teeth receiving a commercial pit-and-fissure sealant (Alpha Seal-DFL and contralateral teeth receiving Icon infiltrant (DMG. Caries progression was monitored by clinical (laser fluorescence caries detection and radiographic examination at 12-month intervals over a period of 3 years of monitored caries progression. Probing the sealing materials to detect areas of retention was also used to evaluate marginal integrity. Results Statistical analysis showed no difference in caries progression using laser fluorescence caries detection when both materials were compared, regardless of the evaluation times (p>0.05. No significance was observed when the marginal sealant integrity of both materials was compared, regardless of the evaluation time (p0.05. SEM analysis exhibited a more homogeneous sealing for the infiltrant than obtained by the sealant. Conclusions The infiltrant was effective to prevent the caries progression in non-cavitated pit-and-fissures after 3 years of clinical evaluation, comparable with the conventional sealant. The infiltrant also presented better results in terms of caries progression at the 3-year evaluation time using the radiographic analysis.

Caries progression in non-cavitated fissures after infiltrant application: a 3-year follow-up of a randomized controlled clinical trial

Science.gov (United States)

ANAUATE-NETTO, Camillo; BORELLI, Laurindo; AMORE, Ricardo; DI HIPÓLITO, Vinicius; D’ALPINO, Paulo Henrique Perlatti

2017-01-01

Abstract Objectives To evaluate the efficacy of a conservative treatment to prevent the progression of caries using an infiltrant on non-cavitated pit and fissures. Material and Methods This controlled clinical trial selected 23 volunteers with clinically and radiographically non-cavitated occlusal caries among patients presenting a “rather low” to “very high” caries risk. Eighty-six teeth were randomly divided into two experimental groups: teeth receiving a commercial pit-and-fissure sealant (Alpha Seal-DFL) and contralateral teeth receiving Icon infiltrant (DMG). Caries progression was monitored by clinical (laser fluorescence caries detection) and radiographic examination at 12-month intervals over a period of 3 years of monitored caries progression. Probing the sealing materials to detect areas of retention was also used to evaluate marginal integrity. Results Statistical analysis showed no difference in caries progression using laser fluorescence caries detection when both materials were compared, regardless of the evaluation times (p>0.05). No significance was observed when the marginal sealant integrity of both materials was compared, regardless of the evaluation time (p0.05). SEM analysis exhibited a more homogeneous sealing for the infiltrant than obtained by the sealant. Conclusions The infiltrant was effective to prevent the caries progression in non-cavitated pit-and-fissures after 3 years of clinical evaluation, comparable with the conventional sealant. The infiltrant also presented better results in terms of caries progression at the 3-year evaluation time using the radiographic analysis. PMID:28877284

Analysis of the preliminary trajectory of emergency venting of the nuclear power plant of Laguna Verde using RELAP5

International Nuclear Information System (INIS)

Cecenas F, M.; Jimenez S, R.; Ovando C, R.; Tijerina S, F.; Tapia M, R. N.

2016-09-01

For a commercial nuclear plant, the availability of a vent line to the atmosphere is an improvement to achieve the prevention and mitigation of the consequences of a severe accident. The importance of this system received greater attention after the Fukushima accident in 2011. Subsequently, in 2012 and 2013, the United States Nuclear Regulatory Commission issued documents stating that the venting must be able to dislodge 1% of the rated thermal power of the core without over pressurizing the primary container. To analyze the venting of the nuclear power plant of Laguna Verde, the line and the primary container are modeled using the thermo-hydraulic code RELAP5, simulating a release of 1% of the nominal licensed power to the container in the form of saturated steam. The vent has no problem to evacuate the energy and manages to keep the container without exceeding its design limit, and the highest percentage of thermal power that can channel the vent to the outside is approximately 3%. A sensitivity analysis increasing the diameter of the line to 14 inches allows increasing in 10% the percentage of power that can be vented to the outside without problem for the containment. (Author)

Microbial Community Structure of Deep-sea Hydrothermal Vents on the Ultraslow Spreading Southwest Indian Ridge

Directory of Open Access Journals (Sweden)

Jian Ding

2017-06-01

Full Text Available Southwest Indian Ridge (SWIR is a typical oceanic ultraslow spreading ridge with intensive hydrothermal activities. The microbial communities in hydrothermal fields including primary producers to support the entire ecosystem by utilizing geochemical energy generated from rock-seawater interactions. Here we have examined the microbial community structures on four hydrothermal vents from SWIR, representing distinct characteristics in terms of temperature, pH and metal compositions, by using Illumina sequencing of the 16S small subunit ribosomal RNA (rRNA genes, to correlate bacterial and archaeal populations with the nature of the vents influenced by ultraslow spreading features. Epsilon-, Gamma-, Alpha-, and Deltaproteobacteria and members of the phylum Bacteroidetes and Planctomycetes, as well as Thaumarchaeota, Woesearchaeota, and Euryarchaeota were dominant in all the samples. Both bacterial and archaeal community structures showed distinguished patterns compared to those in the fast-spreading East Pacific Ridge or the slow-spreading Mid-Atlantic Ridge as previously reported. Furthermore, within SWIR, the microbial communities are highly correlated with the local temperatures. For example, the sulfur-oxidizing bacteria were dominant within bacteria from low-temperature vents, but were not represented as the dominating group recovered from high temperature (over 300°C venting chimneys in SWIR. Meanwhile, Thaumarchaeota, the ammonium oxidizing archaea, only showed high relative abundance of amplicons in the vents with high-temperature in SWIR. These findings provide insights on the microbial community in ultraslow spreading hydrothermal fields, and therefore assist us in the understanding of geochemical cycling therein.

Applying psychological theories to evidence-based clinical practice: identifying factors predictive of placing preventive fissure sealants.

Science.gov (United States)

Bonetti, Debbie; Johnston, Marie; Clarkson, Jan E; Grimshaw, Jeremy; Pitts, Nigel B; Eccles, Martin; Steen, Nick; Thomas, Ruth; Maclennan, Graeme; Glidewell, Liz; Walker, Anne

2010-04-08

Psychological models are used to understand and predict behaviour in a wide range of settings, but have not been consistently applied to health professional behaviours, and the contribution of differing theories is not clear. This study explored the usefulness of a range of models to predict an evidence-based behaviour -- the placing of fissure sealants. Measures were collected by postal questionnaire from a random sample of general dental practitioners (GDPs) in Scotland. Outcomes were behavioural simulation (scenario decision-making), and behavioural intention. Predictor variables were from the Theory of Planned Behaviour (TPB), Social Cognitive Theory (SCT), Common Sense Self-regulation Model (CS-SRM), Operant Learning Theory (OLT), Implementation Intention (II), Stage Model, and knowledge (a non-theoretical construct). Multiple regression analysis was used to examine the predictive value of each theoretical model individually. Significant constructs from all theories were then entered into a 'cross theory' stepwise regression analysis to investigate their combined predictive value. Behavioural simulation - theory level variance explained was: TPB 31%; SCT 29%; II 7%; OLT 30%. Neither CS-SRM nor stage explained significant variance. In the cross theory analysis, habit (OLT), timeline acute (CS-SRM), and outcome expectancy (SCT) entered the equation, together explaining 38% of the variance. Behavioural intention - theory level variance explained was: TPB 30%; SCT 24%; OLT 58%, CS-SRM 27%. GDPs in the action stage had significantly higher intention to place fissure sealants. In the cross theory analysis, habit (OLT) and attitude (TPB) entered the equation, together explaining 68% of the variance in intention. The study provides evidence that psychological models can be useful in understanding and predicting clinical behaviour. Taking a theory-based approach enables the creation of a replicable methodology for identifying factors that may predict clinical behaviour

An analysis of containment venting as a severe accident mitigation strategy for the BWR Mark II containment

International Nuclear Information System (INIS)

Kelly, D.L.; Galyean, W.J.

1990-01-01

An evaluation of a BWR/4 reactor with a Mark-II containment has identified the effects of containment venting on core damage frequency and containment failure mode, and has performed a limited evaluation of the effects on the off-site consequences. The analysis was founded upon an existing probabilistic risk assessment (PRA) with the addition of a proposed filtered containment venting system, based on the Swedish Filtra system installed at the Barseback nuclear power station in southern Sweden. Three different containment venting strategies were examined for their effects on plant risk. These are discussed

Development of high efficiency filtered containment venting system by using AgX

International Nuclear Information System (INIS)

Narabayashi, Tadashi; Fujii, Yasuhiro; Chiba, Go; Tsuji, Masashi; Ishii, Tasuku

2014-01-01

Fukushima Daiichi NPP accident would be terminated, if sufficient accident countermeasures, such as water proof door, mobile power, etc. In case of Europe, it had already installed the heat removal system and filtered containment venting system (FCVS) from the lessons of TMI and Chernobyl Accidents. Decay heat removal system and CV spray cooling system with FCVS are ensured by using mobile generators and heat exchangers to keep the ultimate heat sink even in any natural disaster, such as large earthquake, big tsunami, sudden flooding etc. In this paper we introduce high decontamination factor FCVS that used Silver Zeolite named AgX, developed by Rasa Industries, Ltd. Hokkaido University has tested wet type FCVS using venturi scrubber in water pool and dry type FCVS using metallic filter for 1st stage, and AgX for 2nd stage. Since the AgX needs super heat steam, it is possible to heat up steam by heat exchanger. It is confirmed by TRAC analysis. (author)

Heat Source for Active Venting at the Lost City Hydrothermal Field

Science.gov (United States)

Smith, J. E.; Germanovich, L. N.; Lowell, R. P.

2014-12-01

Located at the inside corner high of the Mid-Atlantic Ridge (MAR), 30°N and the Atlantis Transform Fault (ATF), the Atlantis Massif has been uplifted over the past ~2 my. The Southern Ridge of this massif hosts the Lost City Hydrothermal Field (LCHF), an off-axis hydrothermal vent field with carbonate chimney ages surpassing 120,000 yrs. The fluids discharging at LCHF carry geochemical signals that show a direct interaction with serpentinites. However, mineralogical evidence suggests that peridotite hydration began early in the formation of oceanic core complexes and previous modeling results indicate that serpentinization is unlikely to generate the heat necessary to maintain current levels of discharge at LCHF. This work develops a model for the LCHF venting based on the evidence of tectonic strain, detachment faulting, serpentinization, and convective fluid flow. We constrain fluid flow at the LCHF by vent geochemistry, vent temperature, seismically inferred faulting, and expected geothermal gradient ≈100°C/km. Present understanding of tectonic processes at the intersection of MAR and ATF suggests that unroofing of the footwall and crustal flexing of the massif induced normal faults, which run parallel to the MAR, throughout the Southern Ridge. In the absence of the evidence of magmatism, we test the feasibility of the geothermal gradient to cause fluid circulation in the high-permeability, sub-vertical fault zone. Fluid circulation in the fault zone is complemented by the bulk porous flow driven through the Southern Ridge by the lateral temperature gradient between the cold water on the steep face along the ATF side and the hot interior of the massif. In this scenario, the high pH hydrothermal fluids pass through the serpentinized zone before discharging as both high-temperature focused flow (40°-91°C) and low-temperature (≈15°C) diffuse flow at the LCHF.

Acidophiles of saline water at thermal vents of Vulcano, Italy.

Science.gov (United States)

Simmons, Susan; Norris, R

2002-06-01

DNA was extracted from samples taken from close to acidic hydrothermal vents on shore of the Aeolian Island of Vulcano (Italy). RNA gene sequences were amplified by PCR, cloned, and sequenced. A sequence with an origin in samples at 35 degrees and 45 degrees C corresponded to that of a novel Acidithiobacillus species that was isolated from water close to the vents. Novel, iron-oxidizing mesophilic acidophiles were isolated through enrichment cultures with ferrous iron but were not represented in the clone banks of environmental rDNA. These acidophiles were related to Thiobacillus prosperus, which was isolated previously from Vulcano. The archaeal sequences that comprised a clone bank representing a high-temperature sample (75 degrees C) corresponded to those of Acidianus brierleyi and of thermophiles previously isolated from Vulcano, Thermoplasma volcanium and Acidianus infernus.

Comparison of microleakage between flowable nanocomposite, flowable Composite and Conventional sealant in fissure sealant therapy of the permanent teeth: an in- vitro study

Directory of Open Access Journals (Sweden)

Sara Maleki Kambakhsh

2016-11-01

Full Text Available Background and Aim: Novel dental materials including nanocomposites have been introduced in recent years. It is claimed that they have superior properties such as high esthetic., low wear, increased filler content resulting in better mechanical properties, and releasing ions i.e. fluoride and amorphous calcium phosphate that are important for enamel remineralization. Considering these features, if they have retention and microleakage rates comparable with conventional sealants, these materials can be appropriate alternatives to conventional resin sealants in future. The current study aimed at comparing . microleakage of a flowable nanocomposite, a flowable composite , and a conventional sealant in fissure sealant therapy of the permanent teeth. Materials and Methods: First of all ,42 extracted sound human maxillary first premolars were collected and were randomly divided into 3 equal groups. Then the teeth were embedded in self-cure acrylic resin. Occlusal fissures of the samples were cleaned using explorer, enameloplasty with ¼ round diamond bur and water/air spray was done. The prepared surfaces were etched using 36% phosphoric acid gel for 15s, rinsed and dried. Bonding agent was placed in the pits and fissures, cured for 10s after thinning with air. In the first, second , and the third group conventional sealant, flowable composite , and flowable nanocomposite were placed, respectively; and light cured for 40s. The samples were thermocycled (1000 cycles between 5-55ºC and then immersed in 2% basic Fuchsine solution for 24hs. They were then cut bucculingually and microleakage evaluation was done using stereomicroscope. The obtained data was analyzed using Kruskal wallis tests. Results: There was no significant difference in microleakage rate of the study groups. (P>0.05. Conclusion: Considering the condition of the study, it can be concluded that flowable composite and flowable nanocomposite can be used as suitable alternatives to

Frequency of remnants of sealants left behind in pits and fissures of occlusal surfaces after 2 and 3 years.

NARCIS (Netherlands)

Hu, X.; Zhang, W.; Fan, M.; Mulder, J.; Frencken, J.E.F.M.

2017-01-01

OBJECTIVES: The null-hypothesis tested was that there was no difference in the frequency of remnants of high-viscosity glass-ionomer sealants left behind in pits and fissures of occlusal surfaces of first permanent molars and that of resin composite and glass-carbomer sealants. MATERIALS AND

Vente d'artisanat

CERN Multimedia

Staff Associaiton

2014-01-01

  Éducation et Libération Vente d’artisanat du Tiers Monde Mardi 22 et mercredi 23 avril 2014 CERN, Bâtiment principal Togo, École Arc en ciel, construction des salles de classe. Appel pour le financement de ce chantier afin de libérer l’école de la charge des loyers payés pendant des années. Après nos réalisations en Amérique latine et au Bénin, nous mobilisons nos efforts pour l’école Arc en ciel de Kpémé, au Togo, sur les bords de l’Océan, à mi-chemin entre Lomé et la frontière entre le Bénin et le Togo. Il s’agit d’une école primaire privée, laïque qui a très bonne réputation en termes de résultats, notamment pour les écoliers en fin de scolar...

Population genetic structure of Rufous-Vented Prinia ( Prinia burnesii )

African Journals Online (AJOL)

The objective of the study is to ascertain genetic variation within Rufous-vented Prinia, Prinia burnesii an endemic species, by DNA fingerprinting applying random amplified polymorphic DNA (RAPD) technique. Genetic material was obtained from three distant sites along western bank of River Indus. These sites include ...

Request for approval, vented container annual release fraction; FINAL

International Nuclear Information System (INIS)

HILL, J.S.

1999-01-01

In accordance with the approval conditions for Modification to the Central Waste Complex (CWC) Radioactive Air Emissions Notice of Construction (NOC). dated August 24,1998, a new release fraction has been developed for submittal to the Washington State Department of Health (WDOH). The proposed annual release fraction of 2.50 E-14 is proposed for use in future NOCs involving the storage and handling operations associated with vented containers on the Hanford Site. The proposed annual release fraction was the largest release fraction calculated from alpha measurements of the NucFil filters from 10 vented containers consisting of nine 55-gallon drums and one burial box with dimensions of 9.3 x 5.7 x 6.4 feet. An annual release fraction of 2.0 E-09 was used in the modification to the CWC radioactive air emissions NOC. This study confirmed that the release fraction used in the CWC radioactive air emissions NOC was conservative

Electron microscopy study of microbial mat in the North Fiji basin hydrothermal vent

Science.gov (United States)

Park, H.; Kim, J. W.; Lee, J. W.

2017-12-01

Hydrothermal vent systems consisting of hydrothermal vent, hydrothermal sediment and microbial mat are widely spread around the ocean, particularly spreading axis, continental margin and back-arc basin. Scientists have perceived that the hydrothermal systems, which reflect the primeval earth environment, are one of the best places to reveal the origin of life and extensive biogeochemical process of microbe-mineral interaction. In the present study multiline of analytical methods (X-Ray Diffraction (XRD), Scanning Electron Microscopy (SEM) and Transmission Electron Microscopy (TEM)) were utilized to investigate the mineralogy/chemistry of microbe-mineral interaction in hydrothermal microbial mat. Microbial mat samples were recovered by Canadian scientific submersible ROPOS on South Pacific North Fiji basin KIOST hydrothermal vent expedition 1602. XRD analysis showed that red-colored microbial mat contains Fe-oxides and Fe-oxyhydroxides. Various morphologies of minerals in the red-colored microbial mat observed by SEM are mainly showed sheath shaped, resembled with Leptothrix microbial structure, stalks shaped, similar with Marioprofundus microbial structure and globule shaped microbial structures. They are also detected with DNA analysis. The cross sectional observation of microbial structures encrusted with Fe-oxide and Fe-oxyhydroxide at a nano scale by Transmission Electron Microscopy (TEM) and Focused Ion Beam (FIB) technique was developed to verify the structural/biogeochemical properties in the microbe-mineral interaction. Systematic nano-scale measurements on the biomineralization in the microbial mat leads the understandings of biogeochemical environments around the hydrothermal vent.

Liquid Transfer Cryogenic Test Facility: Initial hydrogen and nitrogen no-vent fill data

Science.gov (United States)

Moran, Matthew E.; Nyland, Ted W.; Papell, S. Stephen

1990-01-01

The Liquid Transfer Cryogenic Test Facility is a versatile testbed for ground-based cryogenic fluid storage, handling, and transfer experimentation. The test rig contains two well instrumented tanks, and a third interchangeable tank, designed to accommodate liquid nitrogen or liquid hydrogen testing. The internal tank volumes are approx. 18, 5, and 1.2 cu. ft. Tank pressures can be varied from 2 to 30 psia. Preliminary no vent fill tests with nitrogen and hydrogen were successfully completed with the test rig. Initial results indicate that no vent fills of nitrogen above 90 percent full are achievable using this test configuration, in a 1-g environment, and with inlet liquid temperatures as high as 143 R, and an average tank wall temperature of nearly 300 R. This inlet temperature corresponds to a saturation pressure of 19 psia for nitrogen. Hydrogen proved considerably more difficult to transfer between tanks without venting. The highest temperature conditions resulting in a fill level greater than 90 percent were with an inlet liquid temperature of 34 R, and an estimated tank wall temperature of slightly more than 100 R. Saturation pressure for hydrogen at this inlet temperature is 10 psia. All preliminary no vent fill tests were performed with a top mounted full cone nozzle for liquid injection. The nozzle produces a 120 degree conical droplet spray at a differential pressure of 10 psi. Pressure in the receiving tank was held to less than 30 psia for all tests.

Comparison of five methods for the estimation of methane production from vented in vitro systems.

Science.gov (United States)

Alvarez Hess, P S; Eckard, R J; Jacobs, J L; Hannah, M C; Moate, P J

2018-05-23

There are several methods for estimating methane production (MP) from feedstuffs in vented in vitro systems. One method (A; "gold standard") measures methane proportions in the incubation bottle's head space (HS) and in the vented gas collected in gas bags. Four other methods (B, C, D and E) measure methane proportion in a single gas sample from HS. Method B assumes the same methane proportion in the vented gas as in HS, method C assumes constant methane to carbon dioxide ratio, method D has been developed based on empirical data and method E assumes constant individual venting volumes. This study aimed to compare the MP predictions from these methods to that of the gold standard method under different incubation scenarios, to validate these methods based on their concordance with a gold standard method. Methods C, D and E had greater concordance (0.85, 0.88 and 0.81), lower root mean square error (RMSE) (0.80, 0.72 and 0.85) and lower mean bias (0.20, 0.35, -0.35) with the gold standard than did method B (concordance 0.67, RMSE 1.49 and mean bias 1.26). Methods D and E were simpler to perform than method C and method D was slightly more accurate than method E. Based on precision, accuracy and simplicity of implementation, it is recommended that, when method A cannot be used, methods D and E are preferred to estimate MP from vented in vitro systems. This article is protected by copyright. All rights reserved. This article is protected by copyright. All rights reserved.

Diversity and phylogenetic analyses of bacteria from a shallow-waterhydrothermal vent in Milos island (Greece

Directory of Open Access Journals (Sweden)

Donato eGiovannelli

2013-07-01

Full Text Available Studies of shallow-water hydrothermal vents have been lagging behind their deep-sea counterparts. Hence, the importance of these systems and their contribution to the local and regional diversity and biogeochemistry is unclear. This study analyzes the bacterial community along a transect at the shallow-water hydrothermal vent system of Milos island, Greece. The abundance and biomass of the prokaryotic community is comparable to areas not affected by hydrothermal activity and was, on average, 1.34×108 cells g-1. The abundance, biomass and diversity of the prokaryotic community increased with the distance from the center of the vent and appeared to be controlled by the temperature gradient rather than the trophic conditions. The retrieved 16S rRNA gene fragments matched sequences from a variety of geothermal environments, although the average similarity was low (94 %, revealing previously undiscovered taxa. Epsilonproteobacteria constituted the majority of the population along the transect, with an average contribution to the total diversity of 60%. The larger cluster of 16S rRNA gene sequences was related to chemolithoautotrophic Sulfurovum spp., an Epsilonproteobacterium so far detected only at deep-sea hydrothermal vents. The presence of previously unknown lineages of Epsilonproteobacteria could be related to the abundance of organic matter in these systems, which may support alternative metabolic strategies to chemolithoautotrophy. The relative contribution of Gammaproteobacteria to the Milos microbial community increased along the transect as the distance from the center of the vent increased. Further attempts to isolate key species from these ecosystems will be critical to shed light on their evolution and ecology.

Influence of Hydrodynamics on the Larval Supply to Hydrothermal Vents on the East Pacific Rise

Science.gov (United States)

2007-06-01

the species inhabiting the vents are endenic, sessile , benthic invertebrates , so recovery from large disturbances occurs primarily through the...Dubilier, N. (2007). Species identifi- cation of marine invertebrate early stages by whole-larvae in situ hybridisation of 18S ribosomal RNA. Marine Ecology...31] Tyler, P. A. & Young, C. M. (1999). Reproduction and dispersal at vents and cold seeps. Journal of the Marine Biological Association of the

Lipid Biomarkers and Molecular Carbon Isotopes for Elucidating Carbon Cycling Pathways in Hydrothermal Vents

Science.gov (United States)

Zhang, C. L.; Dai, J.; Campbell, B.; Cary, C.; Sun, M.

2003-12-01

Increasing molecular evidence suggests that hydrothermal vents in mid-ocean ridges harbor large populations of free-living bacteria, particularly the epsilon Proteobacteria. However, pathways for carbon metabolism by these bacteria are poorly known. We are addressing this question by analyzing the lipid biomarkers and their isotope signatures in environments where the epsilon Proteobacteria are likely predominant. Solid materials were collected from hydrothermal vents in the East Pacific Rise and at the Guaymas Basin in the Gulf of California. Fatty acids extracted from these samples are dominated by 16:0 (27-41%), 18:0 (16-48%), 18:1 (11-42%), 16:1 (7-12%), and 14:0 (5-28%). In addition, 15:0 and anteiso-15:0 are significantly present (2-3%) in samples from the Guaymas Basin. The isotopic compositions of these fatty acids range from -15.0\\permil to -33.1\\permil with the most positive values occurring only in monounsaturated fatty acids (16:1 and 18:1). We are currently unable to assign these biomarkers to any of the epsilon Proteobacteria because biomarkers are poorly known for these organisms isolated from the vents. However, no polyunsaturated fatty acids were detected in these samples, which are consistent with the absence of vent animals at the sampling sites. Signature biomarkers of 20:1 and cy21:0, which are characteristic of the thermophilic chemolithoautotrophs such as Aquificales, are also absent in these samples. These results imply that the deeply branched Aquificales species do not constitute the major microbial community in these vent environments. The large range of molecular isotopic compositions suggests that these lipids are synthesized from various carbon sources with different isotopic compositions or through different biosynthetic pathways, or both. We are currently measuring the isotopic compositions of the total organic carbon in the bulk samples and will determine the fractionations between lipid biomarkers and the total organic carbon

Chemistry of a serpentinization-controlled hydrothermal system at the Lost City hydrothermal vent field

Science.gov (United States)

Ludwig, K. A.; Kelley, D. S.; Butterfield, D. A.; Nelson, B. K.; Karson, J. A.

2003-12-01

The Lost City Hydrothermal Field (LCHF), at 30° N near the Mid-Atlantic Ridge, is an off-axis, low temperature, high-pH, ultramafic-hosted vent system. Within the field, carbonate chimneys tower up to 60 m above the seafloor, making them the tallest vent structures known. The chemistry of the vent structures and fluids at the LCHF is controlled by reactions between seawater and ultramafic rocks beneath the Atlantis massif. Mixing of warm alkaline vent fluids with seawater causes precipitation of calcium carbonate and growth of the edifaces, which range from tall, graceful pinnacles to fragile flanges and colloform deposits. Geochemical and petrological analyses of the carbonate rocks reveal distinct differences between the active and extinct structures. Actively venting chimneys and flanges are extremely porous, friable formations composed predominantly of aragonite and brucite. These structures provide important niches for well-developed microbial communities that thrive on and within the chimney walls. Some of the active chimneys may also contain the mineral ikaite, an unstable, hydrated form of calcium carbonate. TIMS and ICP-MS analyses of the carbonate chimneys show that the most active chimneys have low Sr isotope values and that they are low in trace metals (e.g., Mn, Ti, Pb). Active structures emit high-pH, low-Mg fluids at 40-90° C. The fluids also have low Sr values, indicating circulation of hydrothermal solutions through the serpentinite bedrock beneath the field. In contrast to the active structures, extinct chimneys are less porous, are well lithified, and they are composed predominantly of calcite that yields Sr isotopes near seawater values. Prolonged lower temperature seawater-hydrothermal fluid interaction within the chimneys results in the conversion of aragonite to calcite and in the enrichment of some trace metals (e.g., Mn, Ti, Co, Zn). It also promotes the incorporation of foraminifera within the outer, cemented walls of the carbonate

A clinical trial to evaluate the retention of a silver cermet-ionomer cement used as a fissure sealant.

Science.gov (United States)

Mills, R W; Ball, I A

1993-01-01

A randomized clinical trial was under-taken to compare the retention of a silver cermet-ionomer cement, Ketac Silver, with a conventional, autopolymerizing BIS-GMA resin sealant, Delton, using matched pairs of fissure sites within each subject's mouth. One hundred twenty matched contralateral pairs of fissure sites in first and second permanent molars of 53 school children were sealed with the two materials. The choice of site and material was selected at random. The ages of the children ranged from five to 16 years; first permanent molars were sealed in the five- to 10-year age group, and second permanent molars in the 11- to 16-year age group. Sealants were assessed as present, partly present, or absent at 6, 12, and 24 months. The number of pairs of sites available for reassessment declined from 102 at six months to 59 at 24 months as patients were lost to the study. Retention rates were higher for the Ketac Silver sealants at all three inspection intervals (P cermet cement was better retained than conventional resin sealants in younger children.

Origins of feeding arteries of hepatocellular carcinoma located near the umbilical fissure of the left hepatic lobe: angiographic evaluation.

Science.gov (United States)

Miyayama, Shiro; Yamashiro, Masashi; Shibata, Yoshihiro; Hashimoto, Masahiro; Yoshida, Miki; Tsuji, Kazunobu; Toshima, Fumihito; Matsui, Osamu

2012-12-01

To analyze the origins of the feeding arteries of hepatocellular carcinomas (HCCs) near the umbilical fissure of the left hepatic lobe. Twenty-eight HCCs with a mean ± SD tumor diameter of 3.4 ± 1.0 cm (range 1-4.4 cm) in contact with the right or left side of the umbilical fissure were treated by superselective transcatheter arterial chemoembolization (TACE). The origins of the tumor-feeding arteries were analyzed with arteriograms and computed tomography or cone-beam computed tomography images obtained during and 1 week after TACE. Twenty-one HCC lesions were located in segment 3 and seven were located in segment 4. Of 21 tumors in segment 3, 13 (61.9%) were supplied by the lateral inferior subsegmental artery (A3), three (14.3%) by the medial subsegmental artery (A4), three (14.3%) by both A4 and A3, one (4.8%) by a branch arising from the left lateral hepatic artery, and one (4.8%) by a branch of the right gastric artery. In particular, all tumor-feeding branches arising from A4 were the first branch of A4. Of seven tumors in segment 4, four (57.1%) were supplied by A4 and three (42.9%) by A3. In particular, all tumor-feeding branches arising from A3 were the first branch of A3. This study demonstrates crossover blood supply to HCC lesions located near the umbilical fissure, in addition to direct feeding from a separate branch. In particular, the first branch of the opposite subsegmental artery may feed tumors when crossover blood supply is present.

Origins of Feeding Arteries of Hepatocellular Carcinoma Located Near the Umbilical Fissure of the Left Hepatic Lobe: Angiographic Evaluation

Energy Technology Data Exchange (ETDEWEB)

Miyayama, Shiro, E-mail: s-miyayama@fukui.saiseikai.or.jp; Yamashiro, Masashi; Shibata, Yoshihiro; Hashimoto, Masahiro; Yoshida, Miki; Tsuji, Kazunobu; Toshima, Fumihito [Fukuiken Saiseikai Hospital, Department of Diagnostic Radiology (Japan); Matsui, Osamu [Kanazawa University Graduate School of Medical Science, Department of Radiology (Japan)

2012-12-15

Purpose: To analyze the origins of the feeding arteries of hepatocellular carcinomas (HCCs) near the umbilical fissure of the left hepatic lobe. Methods: Twenty-eight HCCs with a mean {+-} SD tumor diameter of 3.4 {+-} 1.0 cm (range 1-4.4 cm) in contact with the right or left side of the umbilical fissure were treated by superselective transcatheter arterial chemoembolization (TACE). The origins of the tumor-feeding arteries were analyzed with arteriograms and computed tomography or cone-beam computed tomography images obtained during and 1 week after TACE.ResultsTwenty-one HCC lesions were located in segment 3 and seven were located in segment 4. Of 21 tumors in segment 3, 13 (61.9%) were supplied by the lateral inferior subsegmental artery (A3), three (14.3%) by the medial subsegmental artery (A4), three (14.3%) by both A4 and A3, one (4.8%) by a branch arising from the left lateral hepatic artery, and one (4.8%) by a branch of the right gastric artery. In particular, all tumor-feeding branches arising from A4 were the first branch of A4. Of seven tumors in segment 4, four (57.1%) were supplied by A4 and three (42.9%) by A3. In particular, all tumor-feeding branches arising from A3 were the first branch of A3. Conclusion: This study demonstrates crossover blood supply to HCC lesions located near the umbilical fissure, in addition to direct feeding from a separate branch. In particular, the first branch of the opposite subsegmental artery may feed tumors when crossover blood supply is present.

Technology Solutions Case Study: Design Guidance for Passive Vents in New Construction, Multifamily Buildings

Energy Technology Data Exchange (ETDEWEB)

None

2016-02-12

In an effort to improve indoor air quality in high-performance, new construction, multifamily buildings, dedicated sources of outdoor air are being implemented. Passive vents are being selected by some design teams over other strategies because of their lower first costs and operating costs. The U.S. Department of Energy’s Building America research team Consortium for Advanced Residential Buildings constructed eight steps, which outline the design and commissioning required for these passive vents to perform as intended.

Assessment and control design for steam vent noise in an oil refinery.

Science.gov (United States)

Monazzam, Mohammad Reza; Golmohammadi, Rostam; Nourollahi, Maryam; Momen Bellah Fard, Samaneh

2011-06-13

Noise is one of the most important harmful agents in work environment. Noise pollution in oil refinery industries is related to workers' health. This study aimed to determine the overall noise pollution of an oil refinery operation and its frequency analysis to determine the control plan for a vent noise in these industries. This experimental study performed in control unit of Tehran Oil Refinery in 2008. To determine the noise distributions, environmental noise measurements were carried out by lattice method according to basic information and technical process. The sound pressure level and frequency distribution was measured for each study sources subject separately was performed individually. According to the vent's specification, the measured steam noise characteristics reviewed and compared to the theoretical results of steam noise estimation. Eventually, a double expansion muffler was designed. Data analysis and graphical design were carried out using Excel software. The results of environmental noise measurements indicated that the level of sound pressure was above the national permitted level (85 dB (A)). The Mean level of sound pressure of the studied steam jet was 90.3 dB (L). The results of noise frequency analysis for the steam vents showed that the dominant frequency was 4000 Hz. To obtain 17 dB noise reductions, a double chamber aluminum muffler with 500 mm length and 200 mm diameter consisting pipe drilled was designed. The characteristics of steam vent noise were separated from other sources, a double expansion muffler was designed using a new method based on the level of steam noise, and principle sound frequency, a double expansion muffler was designed.

Field Testing of an Unvented Roof with Fibrous Insulation, Tiles, and Vapor Diffusion Venting

Energy Technology Data Exchange (ETDEWEB)

Ueno, K. [Building Science Corporation, Westford, MA (United States); Lstiburek, J. W. [Building Science Corporation, Westford, MA (United States)

2016-02-01

This research is a test implementation of an unvented tile roof assembly in a hot-humid climate (Orlando, FL; Zone 2A), insulated with air permeable insulation (netted and blown fiberglass). Given the localized moisture accumulation and failures seen in previous unvented roof field work, it was theorized that a 'diffusion vent' (water vapor open, but air barrier 'closed') at the highest points in the roof assembly might allow for the wintertime release of moisture, to safe levels. The 'diffusion vent' is an open slot at the ridge and hips, covered with a water-resistant but vapor open (500+ perm) air barrier membrane. As a control comparison, one portion of the roof was constructed as a typical unvented roof (self-adhered membrane at ridge). The data collected to date indicate that the diffusion vent roof shows greater moisture safety than the conventional, unvented roof design.

Radiological Design Summary Report for TRU Vent and Purge Process

International Nuclear Information System (INIS)

Taus, L.B.

2004-01-01

This report contains top-level requirements for the various areas of radiological protection for workers. Detailed quotations of the requirements for applicable regulatory documents can be found in the accompanying Implementation Guide. For the purposes of demonstrating compliance with these requirements, per Engineering Standard 01064, shall consider / shall evaluate indicates that the designer must examine the requirement for the design and either incorporate or provide a technical justification as to why the requirement is not incorporated. The Transuranic Vent and Purge process is not a project, but is considered a process change. This process has been performed successfully by Solid Waste on lower activity TRU drums. This summary report applies a graded approach and describes how the Transuranic Vent and Purge process meets each of the applicable radiological design criteria and requirements specified in Manual WSRC-TM-95-1, Engineering Standard Number 01064

A conservation vent is not a safe substitute for a flame arrester

Energy Technology Data Exchange (ETDEWEB)

Siestrup, Francisco Hubertus Grosse [Protego Leser do Brasil Ltda., Rio de Janeiro, RJ (Brazil)

2009-07-01

For several decades state organizations and engineering societies have published strict engineering guidelines for the design and safe management of storage tanks. Storage tanks in refineries and chemical plants can contain flammable and hazardous chemicals. Accidents in these systems resulting from explosions can cause million dollar property loss and production interruption. In severe cases lawsuits may result and companies can even be driven into bankruptcy. This article focuses on tests which have been conducted by the PROTEGO Research and Development Group in Braunschweig, Germany. Latest research, in which conservation vents have been tested in accordance to the new ISO 16852 test method, have proven that conservation vents cannot be used to substitute a flame arrester if potentially explosive atmospheres are present in storage tanks. This research was conducted during the development of ISO 28300 and the test results are considered in this standard. This paper will prove that the use of conservation vents to protect tanks from atmospheric explosion is not a reliable protection method when the vapor/air mixtures in the tank have a concentration between the Upper and Lower Explosive Limits (UEL and LEL). This is very common for Ethanol storage which is globally in evidence. (author)

The role of flooding in the design of vent and reflux condensers

International Nuclear Information System (INIS)

Sacramento, Julio C.; Heggs, Peter J.

2009-01-01

Reflux and vent condensers are vertical separators where film condensation occurs. A vapour mixture is supplied at the bottom of the tubes and encounters vertical cold surfaces. A falling film forms and exits from the bottom of the tubes, flowing counter-current to the vapour, but co-current to the coolant on the shell side. Flooding occurs when the condensate flow moves from a gravity regime to a shear regime. Vapour velocities at or above the flooding velocity will cause the liquid to exit from the top of the tubes rather than from the bottom. The main disadvantage of these condensers is the limited flooding velocity allowed. Several investigators propose correlations to predict the flooding velocity. In most cases these correlations come from isothermal experiments data, thus the general recommendation of using safety factors of at least 30%. This work compares these correlations to new experimental values of flooding in steam/air vent condensation. The experimental apparatus is a 3 m long, double-pipe condenser with an internal diameter of 0.028 m. The conclusions presented here will aid the design engineer to understand better the applicability of the discussed correlations in the design of steam/air vent condensers

Program plan for the investigation of vent-filtered containment conceptual designs for light water reactors

International Nuclear Information System (INIS)

Benjamin, A.S.

1979-10-01

The implementation of a containment venting and filtration capability has been suggested as a means for reducing the risk from fuel melt accidents in light water reactors. The risk reduction potential of such systems depends upon the dual function of venting containment to prevent overpressurization from the generation of steam and noncondensibles and filtering the effluent to limit the release of radioactive materials. This report addresses the major issues involved in such an accident mitigation system and discusses the engineering, technical, and economic questions that will have to be studied before judgments can be made regarding feasibility and effectiveness. A program plan is presented for research leading to the formulation of design requirements for vent-filter containment systems and to a comprehensive assessment of the values versus impacts of such systems

50 CFR 697.21 - Gear identification and marking, escape vent, maximum trap size, and ghost panel requirements.

Science.gov (United States)

2010-10-01

... vent, maximum trap size, and ghost panel requirements. 697.21 Section 697.21 Wildlife and Fisheries... identification and marking, escape vent, maximum trap size, and ghost panel requirements. (a) Gear identification... Administrator finds to be consistent with paragraph (c) of this section. (d) Ghost panel. (1) Lobster traps not...

The Safety and Efficacy of a Mixture of Honey, Olive Oil, and Beeswax for the Management of Hemorrhoids and Anal Fissure: A Pilot Study

Directory of Open Access Journals (Sweden)

Noori S. Al-Waili

2006-01-01

Full Text Available We have found that a mixture of honey, olive oil, and beeswax was effective for treatment of diaper dermatitis, psoriasis, eczema, and skin fungal infection. The mixture has antibacterial properties. A prospective pilot study was conducted to evaluate the therapeutic effect of topical application of the mixture on patients with anal fissure or hemorrhoids.Fifteen consecutive patients, 13 males and 2 females, median age 45 years (range: 28–70, who presented with anal fissure (5 patients or first- to third-degree hemorrhoids (4 with first degree, 4 with second degree, and 2 with third degree, were treated with a 12-h application of a natural mixture containing honey, olive oil, and beeswax in ratio of 1:1:1(v/v/v. Bleeding, itching, edema, and erythema were measured using a scoring method: 0 = none, 1 = mild, 2 = moderate, 3 = severe, and 4 = very severe. The pain score was checked using a visual analog scale (minimum = 0, maximum = 10. Efficacy of treatment was assessed by comparing the symptoms' score before and after treatment; at weekly intervals for a maximum of 4 weeks. The patients were observed for evidence of any adverse effect such as appearance of new signs and symptoms, or worsening of the existing symptoms. The honey mixture significantly reduced bleeding and relieved itching in patients with hemorrhoids. Patients with anal fissure showed significant reduction in pain, bleeding, and itching after the treatment. No side effect was reported with use of the mixture. We conclude that a mixture of honey, olive oil, and beeswax is safe and clinically effective in the treatment of hemorrhoids and anal fissure, which paves the way for further randomized double blind studies.

The uptake and excretion of partially oxidized sulfur expands the repertoire of energy resources metabolized by hydrothermal vent symbioses.

Science.gov (United States)

Beinart, R A; Gartman, A; Sanders, J G; Luther, G W; Girguis, P R

2015-05-07

Symbiotic associations between animals and chemoautotrophic bacteria crowd around hydrothermal vents. In these associations, symbiotic bacteria use chemical reductants from venting fluid for the energy to support autotrophy, providing primary nutrition for the host. At vents along the Eastern Lau Spreading Center, the partially oxidized sulfur compounds (POSCs) thiosulfate and polysulfide have been detected in and around animal communities but away from venting fluid. The use of POSCs for autotrophy, as an alternative to the chemical substrates in venting fluid, could mitigate competition in these communities. To determine whether ESLC symbioses could use thiosulfate to support carbon fixation or produce POSCs during sulfide oxidation, we used high-pressure, flow-through incubations to assess the productivity of three symbiotic mollusc genera-the snails Alviniconcha spp. and Ifremeria nautilei, and the mussel Bathymodiolus brevior-when oxidizing sulfide and thiosulfate. Via the incorporation of isotopically labelled inorganic carbon, we found that the symbionts of all three genera supported autotrophy while oxidizing both sulfide and thiosulfate, though at different rates. Additionally, by concurrently measuring their effect on sulfur compounds in the aquaria with voltammetric microelectrodes, we showed that these symbioses excreted POSCs under highly sulfidic conditions, illustrating that these symbioses could represent a source for POSCs in their habitat. Furthermore, we revealed spatial disparity in the rates of carbon fixation among the animals in our incubations, which might have implications for the variability of productivity in situ. Together, these results re-shape our thinking about sulfur cycling and productivity by vent symbioses, demonstrating that thiosulfate may be an ecologically important energy source for vent symbioses and that they also likely impact the local geochemical regime through the excretion of POSCs.

Multilayer Insulation Ascent Venting Model

Science.gov (United States)

Tramel, R. W.; Sutherlin, S. G.; Johnson, W. L.

2017-01-01

The thermal and venting transient experienced by tank-applied multilayer insulation (MLI) in the Earth-to-orbit environment is very dynamic and not well characterized. This new predictive code is a first principles-based engineering model which tracks the time history of the mass and temperature (internal energy) of the gas in each MLI layer. A continuum-based model is used for early portions of the trajectory while a kinetic theory-based model is used for the later portions of the trajectory, and the models are blended based on a reference mean free path. This new capability should improve understanding of the Earth-to-orbit transient and enable better insulation system designs for in-space cryogenic propellant systems.

Comparative composition, diversity and trophic ecology of sediment macrofauna at vents, seeps and organic falls.

Directory of Open Access Journals (Sweden)

Angelo F Bernardino

Full Text Available Sediments associated with hydrothermal venting, methane seepage and large organic falls such as whale, wood and plant detritus create deep-sea networks of soft-sediment habitats fueled, at least in part, by the oxidation of reduced chemicals. Biological studies at deep-sea vents, seeps and organic falls have looked at macrofaunal taxa, but there has yet to be a systematic comparison of the community-level attributes of sediment macrobenthos in various reducing ecosystems. Here we review key similarities and differences in the sediment-dwelling assemblages of each system with the goals of (1 generating a predictive framework for the exploration and study of newly identified reducing habitats, and (2 identifying taxa and communities that overlap across ecosystems. We show that deep-sea seep, vent and organic-fall sediments are highly heterogeneous. They sustain different geochemical and microbial processes that are reflected in a complex mosaic of habitats inhabited by a mixture of specialist (heterotrophic and symbiont-associated and background fauna. Community-level comparisons reveal that vent, seep and organic-fall macrofauna are very distinct in terms of composition at the family level, although they share many dominant taxa among these highly sulphidic habitats. Stress gradients are good predictors of macrofaunal diversity at some sites, but habitat heterogeneity and facilitation often modify community structure. The biogeochemical differences across ecosystems and within habitats result in wide differences in organic utilization (i.e., food sources and in the prevalence of chemosynthesis-derived nutrition. In the Pacific, vents, seeps and organic-falls exhibit distinct macrofaunal assemblages at broad-scales contributing to ß diversity. This has important implications for the conservation of reducing ecosystems, which face growing threats from human activities.

Genetic Susceptibility to Dental Caries on Pit and Fissure and Smooth Surfaces

Science.gov (United States)

Shaffer, J.R.; Wang, X.; DeSensi, R.S.; Wendell, S.; Weyant, R.J.; Cuenco, K.T.; Crout, R.; McNeil, D.W.; Marazita, M.L.

2012-01-01

Carious lesions are distributed nonuniformly across tooth surfaces of the complete dentition, suggesting that the effects of risk factors may be surface-specific. Whether genes differentially affect caries risk across tooth surfaces is unknown. We investigated the role of genetics on two classes of tooth surfaces, pit and fissure surfaces (PFS) and smooth surfaces (SMS), in more than 2,600 subjects from 740 families. Participants were examined for surface-level evidence of dental caries, and caries scores for permanent and/or primary teeth were generated separately for PFS and SMS. Heritability estimates (h2, i.e. the proportion of trait variation due to genes) of PFS and SMS caries scores were obtained using likelihood methods. The genetic correlations between PFS and SMS caries scores were calculated to assess the degree to which traits covary due to common genetic effects. Overall, the heritability of caries scores was similar for PFS (h2 = 19–53%; p caries scores for both PFS and SMS in the primary dentition was greater than in the permanent dentition and total dentition. With one exception, the genetic correlation between PFS and SMS caries scores was not significantly different from 100%, indicating that (mostly) common genes are involved in the risk of caries for both surface types. Genetic correlation for the primary dentition dfs (decay + filled surfaces) was significantly less than 100% (p caries risk in PFS versus SMS in the primary dentition. PMID:22286298

Clinical and manometric evaluation of women with chronic anal fissure before and after internal subcutaneous lateral sphincterotomy

Directory of Open Access Journals (Sweden)

Silvana Marques e Silva

2012-06-01

Full Text Available OBJECTIVE: To evaluate clinical and manometric parameters of chronic anal fissure females undergoing lateral internal sphincterotomy (LIS. METHODS: A total of eight women with chronic anal fissure who underwent LIS were included in this study. The preoperative assessment was performed one week before surgery and included general and anorectal examination, anorectal manometry, and Jorge Wexner questionnaire. The post operative follow up was made every 15 days until complete healing. Jorge Wexner questionnaires and anorectal manometry were repeated at 1 month and 3 months after the surgery. Time to healing, manometric changes and complications were assessed. RESULTS: All patients had preoperative increased anal resting pressure. The resting pressures and anal canal length were significantly decreased 3 months after surgery. Patients' complaints of itching and bleeding were also reduced. Fissures healed in 7 patients and median healing time was 45 days. No complications were observed due to the procedure. One patient had transient incontinence to flatus. CONCLUSION: Lateral internal sphincterotomy provided clinical improvement and reduced resting pressure of the internal anal sphincter in women with chronic anal fissure.OBJETIVO: Avaliar a evolução clínica e manométrica de mulheres com fissura anal crônica submetidas à esfincterotomia lateral interna subcutânea. MÉTODOS: Estudo prospectivo com oito pacientes. A avaliação inicial foi realizada por meio de questionários, exame físico e manometria anorretal na semana anterior ao procedimento cirúrgico. Durante o período pós-operatório, as pacientes foram avaliadas clinicamente a cada 15 dias, até a cicatrização completa. Os questionários e a manometria anorretal foram repetidos 1 mês e 3 meses após a operação. Foi avaliado o tempo para cicatrização da fissura, as alterações manométricas e as complicações decorrentes do procedimento. RESULTADOS: Todas as pacientes

Assessing Eruption Column Height in Ancient Flood Basalt Eruptions

Science.gov (United States)

Glaze, Lori S.; Self, Stephen; Schmidt, Anja; Hunter, Stephen J.

2015-01-01

A buoyant plume model is used to explore the ability of flood basalt eruptions to inject climate-relevant gases into the stratosphere. An example from the 1986 Izu-Oshima basaltic fissure eruption validates the model's ability to reproduce the observed maximum plume heights of 12-16 km above sea level, sustained above fire-fountains. The model predicts maximum plume heights of 13-17 km for source widths of between 4-16 m when 32% (by mass) of the erupted magma is fragmented and involved in the buoyant plume (effective volatile content of 6 wt%). Assuming that the Miocene-age Roza eruption (part of the Columbia River Basalt Group) sustained fire-fountains of similar height to Izu-Oshima (1.6 km above the vent), we show that the Roza eruption could have sustained buoyant ash and gas plumes that extended into the stratosphere at approximately 45 deg N. Assuming 5 km long active fissure segments and 9000 Mt of SO2 released during explosive phases over a 10-15 year duration, the approximately 180 km of known Roza fissure length could have supported approximately 36 explosive events/phases, each with a duration of 3-4 days. Each 5 km fissure segment could have emitted 62 Mt of SO2 per day into the stratosphere while actively fountaining, the equivalent of about three 1991 Mount Pinatubo eruptions per day. Each fissure segment could have had one to several vents, which subsequently produced lava without significant fountaining for a longer period within the decades-long eruption. Sensitivity of plume rise height to ancient atmospheric conditions is explored. Although eruptions in the Deccan Traps (approximately 66 Ma) may have generated buoyant plumes that rose to altitudes in excess of 18 km, they may not have reached the stratosphere because the tropopause was substantially higher in the late Cretaceous. Our results indicate that some flood basalt eruptions, such as Roza, were capable of repeatedly injecting large masses of SO2 into the stratosphere. Thus sustained

Comparison Of Vented And Absolute Pressure Transducers For Water-Level Monitoring In Hanford Site Central Plateau Wells

International Nuclear Information System (INIS)

Mcdonald, J.P.

2011-01-01

Automated water-level data collected using vented pressure transducers deployed in Hanford Site Central Plateau wells commonly display more variability than manual tape measurements in response to barometric pressure fluctuations. To explain this difference, it was hypothesized that vented pressure transducers installed in some wells are subject to barometric pressure effects that reduce water-level measurement accuracy. Vented pressure transducers use a vent tube, which is open to the atmosphere at land surface, to supply air pressure to the transducer housing for barometric compensation so the transducer measurements will represent only the water pressure. When using vented transducers, the assumption is made that the air pressure between land surface and the well bore is in equilibrium. By comparison, absolute pressure transducers directly measure the air pressure within the wellbore. Barometric compensation is achieved by subtracting the well bore air pressure measurement from the total pressure measured by a second transducer submerged in the water. Thus, no assumption of air pressure equilibrium is needed. In this study, water-level measurements were collected from the same Central Plateau wells using both vented and absolute pressure transducers to evaluate the different methods of barometric compensation. Manual tape measurements were also collected to evaluate the transducers. Measurements collected during this study demonstrated that the vented pressure transducers over-responded to barometric pressure fluctuations due to a pressure disequilibrium between the air within the wellbores and the atmosphere at land surface. The disequilibrium is thought to be caused by the relatively long time required for barometric pressure changes to equilibrate between land surface and the deep vadose zone and may be exacerbated by the restriction of air flow between the well bore and the atmosphere due to the presence of sample pump landing plates and well caps. The

Explosion testing for the container venting system

International Nuclear Information System (INIS)

Cashdollar, K.L.; Green, G.M.; Thomas, R.A.; Demiter, J.A.

1993-01-01

As part of the study of the hazards of inspecting nuclear waste stored at the Hanford Site, the US Department of Energy and Westinghouse Hanford Company have developed a container venting system to sample the gases that may be present in various metal drums and other containers. In support of this work, the US Bureau of Mines has studied the probability of ignition while drilling into drums and other containers that may contain flammable gas mixtures. The Westinghouse Hanford Company drilling procedure was simulated by tests conducted in the Bureau's 8-liter chamber, using the same type of pneumatic drill that will be used at the Hanford Site. There were no ignitions of near-stoichiometric hydrogen-air or methane-air mixtures during the drilling tests. The temperatures of the drill bits and lids were measured by an infrared video camera during the drilling tests. These measured temperatures are significantly lower than the ∼500 degree C autoignition temperature of uniformly heated hydrogen-air or the ∼600 degree C autoignition temperature of uniformly heated methane-air. The temperatures are substantially lower than the 750 degree C ignition temperature of hydrogen-air and 1,220 degree C temperature of methane-air when heated by a 1-m-diameter wire

Passive soil venting at the Chemical Waste Landfill Site at Sandia National Laboratories, Albuquerque, New Mexico

International Nuclear Information System (INIS)

Phelan, J.M.; Reavis, B.; Cheng, W.C.

1995-05-01

Passive Soil Vapor Extraction was tested at the Chemical Waste Landfill (CWL) site at Sandia National Laboratories, New Mexico (SNLIW). Data collected included ambient pressures, differential pressures between soil gas and ambient air, gas flow rates into and out of the soil and concentrations of volatile organic compounds (VOCS) in vented soil gas. From the differential pressure and flow rate data, estimates of permeability were arrived at and compared with estimates from other studies. Flow, differential pressure, and ambient pressure data were collected for nearly 30 days. VOC data were collected for two six-hour periods during this time. Total VOC emissions were calculated and found to be under the limit set by the Resource Conservation and Recovery Act (RCRA). Although a complete process evaluation is not possible with the data gathered, some of the necessary information for designing a passive venting process was determined and the important parameters for designing the process were indicated. More study is required to evaluate long-term VOC removal using passive venting and to establish total remediation costs when passive venting is used as a polishing process following active soil vapor extraction

Applying psychological theories to evidence-based clinical practice: identifying factors predictive of placing preventive fissure sealants

Directory of Open Access Journals (Sweden)

Maclennan Graeme

2010-04-01

Full Text Available Abstract Background Psychological models are used to understand and predict behaviour in a wide range of settings, but have not been consistently applied to health professional behaviours, and the contribution of differing theories is not clear. This study explored the usefulness of a range of models to predict an evidence-based behaviour -- the placing of fissure sealants. Methods Measures were collected by postal questionnaire from a random sample of general dental practitioners (GDPs in Scotland. Outcomes were behavioural simulation (scenario decision-making, and behavioural intention. Predictor variables were from the Theory of Planned Behaviour (TPB, Social Cognitive Theory (SCT, Common Sense Self-regulation Model (CS-SRM, Operant Learning Theory (OLT, Implementation Intention (II, Stage Model, and knowledge (a non-theoretical construct. Multiple regression analysis was used to examine the predictive value of each theoretical model individually. Significant constructs from all theories were then entered into a 'cross theory' stepwise regression analysis to investigate their combined predictive value Results Behavioural simulation - theory level variance explained was: TPB 31%; SCT 29%; II 7%; OLT 30%. Neither CS-SRM nor stage explained significant variance. In the cross theory analysis, habit (OLT, timeline acute (CS-SRM, and outcome expectancy (SCT entered the equation, together explaining 38% of the variance. Behavioural intention - theory level variance explained was: TPB 30%; SCT 24%; OLT 58%, CS-SRM 27%. GDPs in the action stage had significantly higher intention to place fissure sealants. In the cross theory analysis, habit (OLT and attitude (TPB entered the equation, together explaining 68% of the variance in intention. Summary The study provides evidence that psychological models can be useful in understanding and predicting clinical behaviour. Taking a theory-based approach enables the creation of a replicable methodology for

Bacterial and archaeal communities in the deep-sea sediments of inactive hydrothermal vents in the Southwest India Ridge

Science.gov (United States)

Zhang, Likui; Kang, Manyu; Xu, Jiajun; Xu, Jian; Shuai, Yinjie; Zhou, Xiaojian; Yang, Zhihui; Ma, Kesen

2016-05-01

Active deep-sea hydrothermal vents harbor abundant thermophilic and hyperthermophilic microorganisms. However, microbial communities in inactive hydrothermal vents have not been well documented. Here, we investigated bacterial and archaeal communities in the two deep-sea sediments (named as TVG4 and TVG11) collected from inactive hydrothermal vents in the Southwest India Ridge using the high-throughput sequencing technology of Illumina MiSeq2500 platform. Based on the V4 region of 16S rRNA gene, sequence analysis showed that bacterial communities in the two samples were dominated by Proteobacteria, followed by Bacteroidetes, Actinobacteria and Firmicutes. Furthermore, archaeal communities in the two samples were dominated by Thaumarchaeota and Euryarchaeota. Comparative analysis showed that (i) TVG4 displayed the higher bacterial richness and lower archaeal richness than TVG11; (ii) the two samples had more divergence in archaeal communities than bacterial communities. Bacteria and archaea that are potentially associated with nitrogen, sulfur metal and methane cycling were detected in the two samples. Overall, we first provided a comparative picture of bacterial and archaeal communities and revealed their potentially ecological roles in the deep-sea environments of inactive hydrothermal vents in the Southwest Indian Ridge, augmenting microbial communities in inactive hydrothermal vents.

49 CFR 192.187 - Vaults: Sealing, venting, and ventilation.

Science.gov (United States)

2010-10-01

... explosive mixture might be ignited, and there must be a means for testing the internal atmosphere before removing the cover; (2) If the vault or pit is vented, there must be a means of preventing external sources... ventilating effect of a pipe 4 inches (102 millimeters) in diameter; (2) The ventilation must be enough to...

Diversity and phylogenetic analyses of bacteria from a shallow-water hydrothermal vent in Milos island (Greece).

Science.gov (United States)

Giovannelli, Donato; d'Errico, Giuseppe; Manini, Elena; Yakimov, Michail; Vetriani, Costantino

2013-01-01

Studies of shallow-water hydrothermal vents have been lagging behind their deep-sea counterparts. Hence, the importance of these systems and their contribution to the local and regional diversity and biogeochemistry is unclear. This study analyzes the bacterial community along a transect at the shallow-water hydrothermal vent system of Milos island, Greece. The abundance and biomass of the prokaryotic community is comparable to areas not affected by hydrothermal activity and was, on average, 1.34 × 10(8) cells g(-1). The abundance, biomass and diversity of the prokaryotic community increased with the distance from the center of the vent and appeared to be controlled by the temperature gradient rather than the trophic conditions. The retrieved 16S rRNA gene fragments matched sequences from a variety of geothermal environments, although the average similarity was low (94%), revealing previously undiscovered taxa. Epsilonproteobacteria constituted the majority of the population along the transect, with an average contribution to the total diversity of 60%. The larger cluster of 16S rRNA gene sequences was related to chemolithoautotrophic Sulfurovum spp., an Epsilonproteobacterium so far detected only at deep-sea hydrothermal vents. The presence of previously unknown lineages of Epsilonproteobacteria could be related to the abundance of organic matter in these systems, which may support alternative metabolic strategies to chemolithoautotrophy. The relative contribution of Gammaproteobacteria to the Milos microbial community increased along the transect as the distance from the center of the vent increased. Further attempts to isolate key species from these ecosystems will be critical to shed light on their evolution and ecology.

A lumped model of venting during thermal runaway in a cylindrical Lithium Cobalt Oxide lithium-ion cell

Science.gov (United States)

Coman, Paul T.; Rayman, Sean; White, Ralph E.

2016-03-01

This paper presents a mathematical model built for analyzing the intricate thermal behavior of a 18650 LCO (Lithium Cobalt Oxide) battery cell during thermal runaway when venting of the electrolyte and contents of the jelly roll (ejecta) is considered. The model consists of different ODEs (Ordinary Differential Equations) describing reaction rates and electrochemical reactions, as well as the isentropic flow equations for describing electrolyte venting. The results are validated against experimental findings from Golubkov et al. [1] [Andrey W. Golubkov, David Fuchs, Julian Wagner, Helmar Wiltsche, Christoph Stangl, Gisela Fauler, Gernot Voitice Alexander Thaler and Viktor Hacker, RSC Advances, 4:3633-3642, 2014] for two cases - with flow and without flow. The results show that if the isentropic flow equations are not included in the model, the thermal runaway is triggered prematurely at the point where venting should occur. This shows that the heat dissipation due to ejection of electrolyte and jelly roll contents has a significant contribution. When the flow equations are included, the model shows good agreement with the experiment and therefore proving the importance of including venting.

Mitigation options : flare and vent mitigation undercuts CCS in trimming CO{sub 2} emissions

Energy Technology Data Exchange (ETDEWEB)

Smith, M.

2010-11-15

This article reported on a study aimed at reducing flaring and venting associated with conventional heavy oil production. In particular, the study analyzed parameters such as the variability in flare volumes, flare gas composition and statistical distribution of volumes flared. The objective was to determine the most viable economic solution to reducing flare and vent volumes. In particular, the study focused on various scenarios to tie-in currently flared and vented solution gas. Solution gas volume variability was found to be wide ranging, with 90 percent of sites handling less than 32 percent of the volume and 10 percent of the sites handling more than two-thirds of the volume. Composition also varied, and was difficult to measure. One scenario assumed that wells were unconnected and had to be tied in with their own compressors and pipe, while another scenario considered the wells to be individual wells. A first comprehensive analysis of flare and vent mitigation opportunities in Alberta revealed that tying in solution gas at battery sites could create emissions reductions at much lower cost than the province's carbon capture and storage (CCS) plan. The study of mitigation options primarily targeted the conventional heavy oil belt of eastern Alberta near Lloydminster. The most optimistic scenario included a $15 per tonne carbon credit, that up to 55 megatonnes could be trimmed over 10 years at no cost to the industry.1 fig.

The spatial scale of genetic subdivision in populations of Ifremeria nautilei, a hydrothermal-vent gastropod from the southwest Pacific

Directory of Open Access Journals (Sweden)

Thaler Andrew D

2011-12-01

Full Text Available Abstract Background Deep-sea hydrothermal vents provide patchy, ephemeral habitats for specialized communities of animals that depend on chemoautotrophic primary production. Unlike eastern Pacific hydrothermal vents, where population structure has been studied at large (thousands of kilometres and small (hundreds of meters spatial scales, population structure of western Pacific vents has received limited attention. This study addresses the scale at which genetic differentiation occurs among populations of a western Pacific vent-restricted gastropod, Ifremeria nautilei. Results We used mitochondrial and DNA microsatellite markers to infer patterns of gene flow and population subdivision. A nested sampling strategy was employed to compare genetic diversity in discrete patches of Ifremeria nautilei separated by a few meters within a single vent field to distances as great as several thousand kilometres between back-arc basins that encompass the known range of the species. No genetic subdivisions were detected among patches, mounds, or sites within Manus Basin. Although I. nautilei from Lau and North Fiji Basins (~1000 km apart also exhibited no evidence for genetic subdivision, these populations were genetically distinct from the Manus Basin population. Conclusions An unknown process that restricts contemporary gene flow isolates the Manus Basin population of Ifremeria nautilei from widespread populations that occupy the North Fiji and Lau Basins. A robust understanding of the genetic structure of hydrothermal vent populations at multiple spatial scales defines natural conservation units and can help minimize loss of genetic diversity in situations where human activities are proposed and managed.

Analysis of Depressurization Performance in Containment of Wolsong NPP Unit 1 through Containment Filtered Venting System

International Nuclear Information System (INIS)

Lee, Sunghan; Kim, Jinhyuck; Suh, Nam Duk; Cho, Songwon

2014-01-01

Containment filtered venting system (CFVS) is designed to open and to close isolation valves passively by an operator. CFVS is operated when the containment pressure exceeds the design pressure (225 kPa(a)) and is closed when the containment pressure decreases below 151 kPa(a). The aim of this study is to analyze the depressurization performance of Wolsong unit 1 through CFVS during SBO. The thermal-hydraulic behavior in containment of Wolsong unit 1 was evaluated using the MELCOR 1.8.6 code developed at Sandia National Laboratories (SNL) for the U.S. Nuclear Regulatory Commission (NRC). In addition, in order to evaluate the effects of the CFVS according to the venting area, a sensitivity study depending on different venting area of the CFVS was conducted. Finally, an analysis of the effects of filtering and scrubbing of radioactive material for CFVS is important but not treated in this paper. The SBO accident is chosen to analyze the thermal-hydraulic behavior of Wolsong unit 1. During SBO, the analysis of CFVS affecting on the depressurization of the containment was conducted using MELCOR 1.8.6 code. Also, a sensitivity study was carried out to evaluate the depressurization performance according to the venting area of CFVS. The results show that the containment pressure is considerably decreased and the integrity of the containment could be maintained in case of CFVS operating. Therefore, CFVS has the capacity to keep the containment pressure below the design pressure during SBO. In addition, there are large differences in the containment pressure depending on venting area. We found that the decreasing rate of the pressure in the containment and water level in CFVS depends on the venting area. In the future, a proper requirement for CFVS sizing criteria according to accident scenarios such as LBLOCA, SBLOCA and SGTR, etc. should be evaluated in order to review the licensing for CFVS. Finally, analyses of aerosols, fission product, and radioactive material

Arsenic bioaccumulation and biotransformation in deep-sea hydrothermal vent organisms from the PACMANUS hydrothermal field, Manus Basin, PNG

Science.gov (United States)

Price, Roy E.; Breuer, Christian; Reeves, Eoghan; Bach, Wolfgang; Pichler, Thomas

2016-11-01

As-Bet (42% As-Bet compared to 48% AsIII and 10% AsV), suggesting As-Bet is a metabolite. Trace arsenosugar (SO4-sug) was observed in digestive gland and gills only. The other snail, I. nautilei, was also dominated by AsIII and AsV in digestive glands (82, 10%) and gills (80, 10%), with 6-9% As-Bet, but its muscle contained 62% As-Bet and 32% AsIII, with 7% trimethylarsoniopropionate (TMAP). Trace dimethylarsinic acid (DMAV) was observed in its gills, and trace TMAP and arsenocholine (AC) was observed in digestive glands. The mussel B. manusensis was dominated by As-Bet in all three tissue types. Digestive gland and gills contained 22% AsIII, 5-10% AsV, 20-25% DMAV, along with some TMAP and tetramethylarsonium ion (TETRA). However, the muscle contained significantly more As-Bet (91.6%), with the only other species being AsIII (8.4%). Unfortunately, as is often the case in bioaccumulation and biotransformation studies, extraction efficiencies were low, limiting any rigorous interpretation of arsenic biotransformation patterns. Through process of elimination, we suggest that arsenosugars may be synthesized by H2S-oxidizing chemotrophic microbial mats, ultimately leading to the syntheses of As-Bet within vent organisms. However, because As-sugs rarely occur in deep-sea vent organisms, As-Bet, as well as TMAP, AC, and TETRA could also potentially be synthesized directly by the "Edmonds" pathway, the proposed arseno-analog to amino acid formation, without the necessity for arsenosugar formation as an intermediate. Future research should endeavor for more comprehensive extraction of organoarsenicals.

Building America Case Study: Design Guidance for Passive Vents in New Construction Multifamily Buildings, New York, New York

Energy Technology Data Exchange (ETDEWEB)

2016-02-01

This document addresses the use of passive vents as a source of outdoor air in multifamily buildings. The challenges associated with implementing passive vents and the factors affecting performance are outlined. A comprehensive design methodology and quantified performance metrics are provided. Two hypothetical design examples are provided to illustrate the process. This document is intended to be useful to designers, decision-makers, and contractors implementing passive ventilation strategies. It is also intended to be a resource for those responsible for setting high-performance building program requirements, especially pertaining to ventilation and outdoor air. To ensure good indoor air quality, a dedicated source of outdoor air is an integral part of high-performance buildings. Presently, there is a lack of guidance pertaining to the design and installation of passive vents, resulting in poor system performance. This report details the criteria necessary for designing, constructing, and testing passive vent systems to enable them to provide consistent and reliable levels of ventilation air from outdoors.

Characterizing the metatranscriptomic profile of archaeal metabolic genes at deep-sea hydrothermal vents in the Mid-Cayman Rise

Science.gov (United States)

Galambos, D.; Reveillaud, J. C.; Anderson, R.; Huber, J. A.

2017-12-01

Deep-sea hydrothermal vent systems host a wide diversity of bacteria, archaea and viruses. Although the geochemical conditions at these vents are well-documented, the relative metabolic activity of microbial lineages, especially among archaea, remains poorly characterized. The deep, slow-spreading Mid-Cayman Rise, which hosts the mafic-influenced Piccard and ultramafic-influenced Von Damm vent fields, allows for the comparison of vent sites with different geochemical characteristics. Previous metagenomic work indicated that despite the distinct geochemistry at Von Damm and Piccard, the functional profile of microbial communities between the two sites was similar. We examined relative metabolic gene activity using a metatranscriptomic analysis and observed functional similarity between Von Damm and Piccard, which is consistent with previous results. Notably, the relative expression of the methyl-coenzyme M reductase (mcr) gene was elevated in both vent fields. Additionally, we analyzed the ratio of RNA expression to DNA abundance of fifteen archaeal metagenome-assembled genomes (MAGs) across the two fields. Previous work showed higher archaeal diversity at Von Damm; our results indicate relatively even expression among archaeal lineages at Von Damm. In contrast, we observed lower archaeal diversity at Piccard, but individual archaeal lineages were very highly expressed; Thermoprotei showed elevated transcriptional activity, which is consistent with higher temperatures and sulfur levels at Piccard. At both Von Damm and Piccard, specific Methanococcus lineages were more highly expressed than others. Future analyses will more closely examine metabolic genes in these Methanococcus MAGs to determine why some lineages are more active at a vent field than others. We will conduct further statistical analyses to determine whether significant differences exist between Von Damm and Piccard and whether there are correlations between geochemical metadata and metabolic gene or

TRANSPORT OF WASTE SIMULANTS IN PJM VENT LINES

Energy Technology Data Exchange (ETDEWEB)

Qureshi, Z

2007-02-21

The experimental work was conducted to determine whether there is a potential for waste simulant to transport or 'creep' up the air link line and contaminate the pulse jet vent system, and possibly cause long term restriction of the air link line. Additionally, if simulant creep occurred, establish operating parameters for washing down the line. The amount of the addition of flush fluids and mixer downtime must be quantified.

3D imaging of vents and sand injectites produced by Lower Cretaceous hydrothermal activity in the southern North Sea

DEFF Research Database (Denmark)

Moreau, Julien

Ma. Strong amplitude anomalies present within the salt are good indication of the presence of igneous intrusions. The vents are imaged as sub-transparent agglomeration of sub-vertical pipe structures emanating above the seismic amplitude anomalies. The vents were analyzed through distinct categories......: size, shape, upper part shape and source bed. Most of the vents originate from the Lower Germanic Triassic Group (Bundsandstein). They are conical in shape and have an eye-shaped upper dome. At the top, numerous domes have been eroded. A few domes have jacked up the overburden, sometimes including...

Sweden employs a multi venturi scrubber for containment venting

International Nuclear Information System (INIS)

Elisson, K.; Waltersten, T.

1988-01-01

The Filtra-MVSS for filtered venting of containment overpressure is a flexible system capable of covering a wide range of hypothetical design basis events for BWRs and PWRs. The system encompasses a number of special features, can be optimized for a specified decontamination factor, and can accommodate a wide range of off-gas flow rates. (author)

A Comparative Evaluation of the Effect of Bonding Agent on the Tensile Bond Strength of Two Pit and Fissure Sealants Using Invasive and Non-invasive Techniques: An in-vitro Study.

Science.gov (United States)

Singh, Shamsher; Adlakha, Vivek; Babaji, Prashant; Chandna, Preetika; Thomas, Abi M; Chopra, Saroj

2013-10-01

Newer technologies and the development of pit and fissure sealants have shifted the treatment philosophy from 'drill and fill' to that of 'seal and heal'. The purpose of this in-vitro study was to evaluate the effects of bonding agents on the tensile bond strengths of two pit and fissure sealants by using invasive and non-invasive techniques. One hundred and twenty bicuspids were collected and teeth were divided into two groups: Group-I (Clinpro) and Group-II (Conseal f) with 60 teeth in each group. For evaluating tensile bond strengths, occlusal surfaces of all the teeth were flattened by reducing buccal and lingual cusps without disturbing fissures. Standardised polyvinyl tube was bonded to occlusal surfaces with respective materials. Sealants were applied, with or without bonding agents, in increments and they were light cured. Tensile bond strengths were determined by using Universal Testing Machine. Data were then statistically analysed by using Student t-test for comparison. A statistically significant difference was found in tensile bond strength in invasive with bonding agent group than in non-invasive with bonding agent group. This study revealed that invasive techniques increase the tensile bond strengths of sealants as compared to non- invasive techniques and that the use of a bonding agent as an intermediate layer between the tooth and fissure sealant is beneficial for increasing the bond strength.

Severe Accident Mitigation through Improvements in Filtered Containment Vent Systems and Containment Cooling Strategies for Water Cooled Reactors. Proceedings of a Technical Meeting

International Nuclear Information System (INIS)

2017-05-01

One of the most important lessons from the accident at the Fukushima Daiichi nuclear power plant is that a reliable containment venting system can be crucial for effective accident management during severe accidents, especially for smaller volume containments in relation to the rated nuclear power. Containment venting can enhance the capability to maintain core cooling and containment integrity as well as reduce uncontrolled radioactive releases to the environment if the venting system has a filtration capacity. In general, a filtered containment vent system increases the flexibility of plant personnel in coping with unforeseen events. This publication provides the overview of the current status of related activities with the goal to share information between Member States on actions, upgrades, and new technologies pertaining to containment cooling and venting.

Filtered containment venting in Sweden

International Nuclear Information System (INIS)

Lindau, L.; Ellisson, K.

1989-01-01

After the TMI accident, Swedish authorities decided that all Swedish nuclear power plants should be upgraded with respect to mitigation of the consequences of severe accidents. One contribution to meet these ends is filtered containment venting, i.e. means to relieve containment overpressure and to clean the relief gas from radioactive components. The first system in operation was built at the Barsebaeck site (2 BWR's) where a gravel bed filter was installed. For the remaining Swedish units (7 BWR's and 3 PWR's) a passive, self-controlling wet scrubber system, FILTRA-MVSS, is now under installation. The principle of the FILTRA-MVSS is a self-controlling, self-pumping venturi collector submerged in a pool, and it is used to filter out emissions of solid and gaseous radioactive components

Pu'u 'Ō'ō-Kūpaianaha eruption of Kilauea, November 1991-February 1994; field data and flow maps

Science.gov (United States)

Heliker, C. Christina; Mangan, Margaret T.; Mattox, Tari N.; Kauahikaua, James P.

1998-01-01

The Pu'u 'Ō'ō-Kūpaianaha eruption on the east rift zone of Kīlauea, which began in January 1983, is the longest-lived rift zone eruption of the last two centuries. By 1994, a broad field of lava, nearly 1 km3 in volume and 12 km wide at the coast, had buried 87 km2 of the volcano's south flank. The initial six months of fissure eruptions (episodes 1-3) were followed by three years of episodic lava fountaining from the Pu'u 'Ō'ō vent (episodes 4–47). In July 1986, after two days of fissure eruptions up- and downrift from Pu'u 'Ō'ō (episodes 48a and 48b), the eruption shifted to a new vent, Kūpaianaha, 3.5 km downrift. For the next five-and-a-half years (episode 48), Kūpaianaha was the site of nearly continuous low-level effusion. The 49th episode occurred in November 1991, when several fissures opened between Pu'u 'Ō'ō and Kūpaianaha (see Mangan and others, 1995, Bulletin of Volcanology, v. 57, p. 127-135). This three-week-long outburst was the result of the waning output of the Kūpaianaha vent, which finally died in February 1992 (see Kauahikaua and others, 1996, Bulletin of Volcanology, v. 57, p. 641-648). The third epoch of the eruption began ten days later, when vents opened on the uprift slope of the Pu'u 'Ō'ō cone. Several flank vents erupted over the next two years (episodes 50-53). In the first year, from February 1992 through February 1993, the low-level effusion was interrupted by 21 brief pauses. These ended with the beginning of episode 53 in February 1993, and for the next year, lava effusion was continuous. Episode 53 was ongoing at the end of the interval covered by this report. During the years that Kūpaianaha was active, the Pu'u 'Ō'ō conduit gradually evolved into a crater 300 m in diameter as the conduit walls collapsed. Beginning in 1987, an active lava pond was intermittently visible in the bottom of the crater; from 1990 on, the pond was almost continuously present. The Pu'u 'Ō‘ō pond drained at the beginning of episode

Detection of occlusal caries with impedance spectroscopy and laser fluorescence before and after placement of fissure sealants: An in vitro study

DEFF Research Database (Denmark)

Mortensen, Diana; Ekstrand, Kim; Twetman, Svante

2016-01-01

, the DIAGNOdent pen and ICDAS at baseline, after bleaching, etching and placement of a clear fissure sealant. A digital radiograph was exposed at baseline. After the assessments, the actual lesion depth was histologically determined.  Results : Bleaching did not affect the readings but significantly higher ACIS...

Propagation of dikes at Vesuvio (Italy) and the effect of Mt. Somma

Science.gov (United States)

Acocella, V.; Porreca, M.; Neri, M.; Massimi, E.; Mattei, M.

2006-04-01

Dikes provide crucial information on how magma propagates within volcanoes. Somma-Vesuvio (Italy) consists of the active Vesuvio cone, partly bordered by the older Mt. Somma edifice. Historical chronicles on the fissure eruptions in 1694-1944 are matched with an analytical solution to define the propagation path of the related dikes and to study any control of the Mt. Somma relief. The fissures always consisted of the downslope migration of vents from an open summit conduit, indicating lateral propagation as the predominant mechanism for shallow dike emplacement. No fissure emplaced beyond Mt. Somma, suggesting that its buttressing hinders the propagation of the radial dikes. An analytical solution is defined to describe the mechanism of formation of the laterally propagating dikes and to evaluate the effect of topography. The application to Somma-Vesuvio suggests that, under ordinary excess magmatic pressures, the dikes should not propagate laterally at depths >240-480 m below the surface, as the increased lithostatic pressure requires magmatic pressures higher than average. This implies that, when the conduit is open, the lateral emplacement of dikes is expectable on the S, W and E slopes. The lack of fissures N of Mt. Somma is explained by its buttressing, which hinders dike propagation.

Examination of the potential problems resulting from the settling of U5 procedure (filtered venting of the containment) on French PWR'S

International Nuclear Information System (INIS)

L'Homme, A.; Serviere, G.

1988-06-01

A filtered venting system of the containment including a sand bed (U5 procedure) is now settled on french PWR's. In this paper, one reviews the problems which are raised, concerning either the efficiency of the system or the safety of the nuclear unit. Two types of situations are examined: design situations, for which the U5 procedure is not used, and hypothetical accidental situations, for which the U5 procedure could be used

Effect of steam condensation on pressure and temperature under hydrogen jet fire in a vented enclosure

International Nuclear Information System (INIS)

Kuznetsov, Mike; Xiao, Jianjun; Travis, Jack

2017-01-01

Hydrogen release through leaks due to the LOCA and MCCI accidents and its immediate ignition leads to formation of hydrogen jet fire in a containment of reactor building. An experimental study of hydrogen jet fire in a chamber of 1x1x1 m 3 volume with different vent position, vent areas from 1 to 90 cm 2 and hydrogen mass flow rates from 0.027 to 1.087 g/s were performed in current work. Depending on hydrogen mass flow rate and vent area a well-ventilated or under-ventilated jet fire regime may occur. In the case of relatively small hydrogen release rate and large vent area, relatively stable jet fire behaviour for well-ventilated jet fire leading to over-pressure not more than 0.8 mbar was found. Three different scenarios of under-ventilated jet fire behaviour with self-extinction, re-ignition and external flame leading to relatively high overpressure of 10-100 mbar were found experimentally and numerically. Numerical simulations with GASFLOW-MPI code were performed with/without modelling heat conduction in solid walls, steam condensation, convective heat transfer and thermal radiation. With heat transfer modelling, both initial pressure peak and pressure decay were very well predicted compared to the experimental data. Numerical simulations were then compared with experimental Background Oriented Schlieren (BOS) images obtained to visualize the hydrogen combustion process. Self-extinction and re-ignition events were captured in the numerical simulation as well. An adiabatic case indicates that heat transfer and steam condensation must be included into the combustion model to accurately predict the physical phenomena of turbulent hydrogen jet flames in a vented enclosure. (author)

FLAME facility: The effect of obstacles and transverse venting on flame acceleration and transition on detonation for hydrogen-air mixtures at large scale

International Nuclear Information System (INIS)

Sherman, M.P.; Tieszen, S.R.; Benedick, W.B.

1989-04-01

This report describes research on flame acceleration and deflagration-to-detonation transition (DDT) for hydrogen-air mixtures carried out in the FLAME facility, and describes its relevance to nuclear reactor safety. Flame acceleration and DDT can generate high peak pressures that may cause failure of containment. FLAME is a large rectangular channel 30.5 m long, 2.44 m high, and 1.83 m wide. It is closed on the ignition end and open on the far end. The three test variables were hydrogen mole fraction (12--30%), degree of transverse venting (by moving steel top plates---0%, 13%, and 50%), and the absence or presence of certain obstacles in the channel (zero or 33% blockage ratio). The most important variable was the hydrogen mole fraction. The presence of the obstacles tested greatly increased the flame speeds, overpressures, and tendency for DDT compared to similar tests without obstacles. Different obstacle configurations could have greater or lesser effects on flame acceleration and DDT. Large degrees of transverse venting reduced the flame speeds, overpressures, and possibility of DDT. For small degrees of transverse venting (13% top venting), the flame speeds and overpressures were higher than for no transverse venting with reactive mixtures (>18% H 2 ), but they were lower with leaner mixtures. The effect of the turbulence generated by the flow out the vents on increasing flame speed can be larger than the effect of venting gas out of the channel and hence reducing the overpressure. With no obstacles and 50% top venting, the flame speeds and overpressures were low, and there was no DDT. For all other cases, DDT was observed above some threshold hydrogen concentration. DDT was obtained at 15% H 2 with obstacles and no transverse venting. 67 refs., 62 figs

Geochemistry of seafloor hydrothermal vent fluids at EPR 9°50'N: Time series data from 2004-2016

Science.gov (United States)

Scheuermann, P.; Pester, N. J.; Tutolo, B. M.; Simmons, S. F.; Seyfried, W. E., Jr.

2017-12-01

Hydrothermal fluids were collected from vent sites along the East Pacific Rise (EPR) at 9°50'N in 2004, 2008 and 2016 in isobaric gas-tight titanium samplers. These dates bracket the seafloor eruption that occurred at EPR 9°50'N between 2005 and 2006. The reported data focus on P vent and Bio9, as these vents were active during all three sampling periods. The concentration of aqueous volatiles reached maxima at both vents in 2008. At P vent, CO2, H2, and H2S were 124 mM/kg, 0.55 mM/kg and 12.2 mM/kg, respectively. The concentrations at Bio9 in 2008 were, 106 mM/kg CO2, 1.1 mM/kg H2, and 12.6 mM/kg H2S. Fe and Mn concentrations were the highest at both vent sites in 2004, and then decreased in 2008 and again in 2016. The range at P vent was 1.5-6.3 mM/kg Fe and 315-1212 uM/kg Mn, while at Bio9 the concentrations were 1.6-3.7 mM/kg Fe and 301-650 uM/kg Mn. The trends in CO2, H2, and H2S at P vent (2008 and 2016) and Bio9 (all years) are consistent with changes in subsurface pressure and temperature as a result of the eruption that alter the conditions at which dissolved components partition between vapor and liquid phases in the NaCl-H2O system. The trend in Fe and Mn concentrations is surprising and highlights the complex partitioning behavior of these elements in systems in which the concentrations are controlled by fluid-mineral equilibria as well as phase separation. Between 2004 and 2008, fluids at P vent transitioned from single-phase (535 mM/kg Cl) to a low-density vapor (370 mM/kg). Upon phase separation, the concentrations of H2S and H2 increased, while Fe and Mn concentrations decreased considerably. These changes highlight the importance of phase separation on controlling mass transfer from the crust to overlying ocean. In contrast to the other aqueous volatiles, CH4 concentrations in 2008 (47 µM) were lower or equal to concentrations in 2004 or 2016, 50-100 µM. CH4 is decoupled from the effects of phase separation, and is likely extracted from fluid

Testing of a Spray-Bar Zero Gravity Cryogenic Vent System for Upper Stages

Science.gov (United States)

Lak, Tibor; Flachbart, Robin; Nguyen, Han; Martin, James

1999-01-01

The capability to vent in zero gravity without resettling is a fundamental technology need that involves practically all uses of subcritical cryogenics in space. Venting without resettling would extend cryogenic orbital transfer vehicle capabilities. However, the lack of definition regarding liquid/ullage orientation coupled with the somewhat random nature of the thermal stratification and resulting pressure rise rates, lead to significant technical challenges. Typically a zero gravity vent concept, termed a thermodynamic vent system (TVS), consists of a tank mixer to destratify the propellant, combined with a Joule- Thomson (J-T) valve to extract then-nal energy from the propellant. In a cooperative effort, Marshall Space Flight Center's (MSFC's) Multipurpose Hydrogen Test Bed (N4HTB) was used to test a unique "spray bar" TVS system developed by Boeing. A schematic of this system is included in Figure 1. The system consists of a recirculation pump, a parallel flow concentric tube, heat exchanger, and a spray bar positioned close to the longitudinal axis of the tank. In the mixing mode, the recirculation pump withdraws liquid from the tank and sprays it radially into the tank liquid, ullage, and exposed tank surfaces. When energy extraction is required, a small portion of the recirculated liquid is passed sequentially through the J-T expansion valve, the spray bar heat exchanger element, and is vented overboard. The vented vapor cools the circulated bulk fluid, thereby removing thermal energy and reducing tank pressure. Figure 2 is a plot of ullage pressure (P4) and liquid vapor pressure (PSAI) versus time. The pump operates alone, cycling on and off, to destratify the tank liquid and ullage until the liquid vapor pressure reaches the lower set point. At that point, the J-T valve begins to cycle on and off with the pump. Thus, for short duration missions, only the mixer may operate, thus minimizing or even eliminating boil-off losses. The primary advantage of the

Field Testing of an Unvented Roof with Fibrous Insulation, Tiles and Vapor Diffusion Venting

Energy Technology Data Exchange (ETDEWEB)

Ueno, K. [Building Science Corporation, Westford, MA (United States); Lstiburek, J. W. [Building Science Corporation, Westford, MA (United States)

2016-02-05

This research is a test implementation of an unvented tile roof assembly in a hot-humid climate (Orlando, FL; Zone 2A), insulated with air permeable insulation (netted and blown fiberglass). Given the localized moisture accumulation and failures seen in previous unvented roof field work, it was theorized that a 'diffusion vent' (water vapor open, but air barrier 'closed') at the highest points in the roof assembly might allow for the wintertime release of moisture, to safe levels. The 'diffusion vent' is an open slot at the ridge and hips, covered with a water-resistant but vapor open (500+ perm) air barrier membrane. As a control comparison, one portion of the roof was constructed as a typical unvented roof (self-adhered membrane at ridge). The data collected to date indicate that the diffusion vent roof shows greater moisture safety than the conventional, unvented roof design. The unvented roof had extended winter periods of 95-100% RH, and wafer (wood surrogate RH sensor) measurements indicating possible condensation; high moisture levels were concentrated at the roof ridge. In contrast, the diffusion vent roofs had drier conditions, with most peak MCs (sheathing) below 20%. In the spring, as outdoor temperatures warmed, all roofs dried well into the safe range (10% MC or less). Some roof-wall interfaces showed moderately high MCs; this might be due to moisture accumulation at the highest point in the lower attic, and/or shading of the roof by the adjacent second story. Monitoring will be continued at least through spring 2016 (another winter and spring).

DUCKS: Low cost thermal monitoring units for near-vent deployment

Science.gov (United States)

Harris, Andrew; Pirie, Dawn; Horton, Keith; Garbeil, Harold; Pilger, Eric; Ramm, Hans; Hoblitt, Rick; Thornber, Carl; Ripepe, Maurizio; Marchetti, Emanuele; Poggi, Pasquale

2005-05-01

During 1999 we designed and tested a thermal monitoring system to provide a cheap, robust, modular, real-time system capable of surviving the hostile conditions encountered proximal to active volcanic vents. In November 2000 the first system was deployed at Pu'u 'O'o (Kilauea, Hawai'i) to target persistently active vents. Aside from some minor problems, such as sensor damage due to tampering, this system remained operational until January 2004. The success of the prototype system led us to use the blueprint for a second installation at Stromboli (Aeolian Islands, Italy). This was deployed, dug into a bomb-proof bunker, during May 2002 and survived the April 2003 paroxysmal eruption despite being located just 250 m from the vent. In both cases, careful waterproofing of connectors and selection of suitable protection has prevented water damage and corrosion in the harsh atmosphere encountered at the crater rim. The Pu'u 'O'o system cost ˜US10,000 and comprises four modules: sensors, transmission and power hub, repeater station and reception site. The sensor component consists of three thermal infrared thermometers housed in Pelican™ cases fitted with Germanium-Arsenide-Selenium windows. Two 1° field of view (FOV) sensors allow specific vents to be targeted and a 60° FOV sensor provides a crater floor overview. A hard wire connection links to a Pelican™-case-housed microprocessor, modem and power module. From here data are transmitted, via a repeater site, to a dedicated PC at the Hawaiian Volcano Observatory. Here data are displayed with a delay of ˜3 s between acquisition and display. The modular design allows for great flexibility. At Stromboli, 1° and 15° FOV sensor modules can be switched depending changes in activity style and crater geometry. In addition a direct line of site to the Stromboli reception center negates the repeater site requirement, reducing the cost to US5500 for a single sensor system. We have also constructed self-contained units

DUCKS: Low cost thermal monitoring units for near-vent deployment

Science.gov (United States)

Harris, A.; Pirie, D.; Horton, K.; Garbeil, H.; Pilger, E.; Ramm, H.; Hoblitt, R.; Thornber, C.; Ripepe, M.; Marchetti, E.; Poggi, P.

2005-01-01

During 1999 we designed and tested a thermal monitoring system to provide a cheap, robust, modular, real-time system capable of surviving the hostile conditions encountered proximal to active volcanic vents. In November 2000 the first system was deployed at Pu'u 'O'o (Kilauea, Hawai'i) to target persistently active vents. Aside from some minor problems, such as sensor damage due to tampering, this system remained operational until January 2004. The success of the prototype system led us to use the blueprint for a second installation at Stromboli (Aeolian Islands, Italy). This was deployed, dug into a bomb-proof bunker, during May 2002 and survived the April 2003 paroxysmal eruption despite being located just 250 m from the vent. In both cases, careful waterproofing of connectors and selection of suitable protection has prevented water damage and corrosion in the harsh atmosphere encountered at the crater rim. The Pu'u 'O'o system cost ???US$10,000 and comprises four modules: sensors, transmission and power hub, repeater station and reception site. The sensor component consists of three thermal infrared thermometers housed in Pelican??? cases fitted with Germanium-Arsenide-Selenium windows. Two 1?? field of view (FOV) sensors allow specific vents to be targeted and a 60?? FOV sensor provides a crater floor overview. A hard wire connection links to a Pelican???-case-housed microprocessor, modem and power module. From here data are transmitted, via a repeater site, to a dedicated PC at the Hawaiian Volcano Observatory. Here data are displayed with a delay of ???3 s between acquisition and display. The modular design allows for great flexibility. At Stromboli, 1?? and 15?? FOV sensor modules can be switched depending changes in activity style and crater geometry. In addition a direct line of site to the Stromboli reception center negates the repeater site requirement, reducing the cost to US$5500 for a single sensor system. We have also constructed self-contained units

High-throughput sequencing and analysis of the gill tissue transcriptome from the deep-sea hydrothermal vent mussel Bathymodiolus azoricus

Directory of Open Access Journals (Sweden)

Gomes Paula

2010-10-01

Full Text Available Abstract Background Bathymodiolus azoricus is a deep-sea hydrothermal vent mussel found in association with large faunal communities living in chemosynthetic environments at the bottom of the sea floor near the Azores Islands. Investigation of the exceptional physiological reactions that vent mussels have adopted in their habitat, including responses to environmental microbes, remains a difficult challenge for deep-sea biologists. In an attempt to reveal genes potentially involved in the deep-sea mussel innate immunity we carried out a high-throughput sequence analysis of freshly collected B. azoricus transcriptome using gills tissues as the primary source of immune transcripts given its strategic role in filtering the surrounding waterborne potentially infectious microorganisms. Additionally, a substantial EST data set was produced and from which a comprehensive collection of genes coding for putative proteins was organized in a dedicated database, "DeepSeaVent" the first deep-sea vent animal transcriptome database based on the 454 pyrosequencing technology. Results A normalized cDNA library from gills tissue was sequenced in a full 454 GS-FLX run, producing 778,996 sequencing reads. Assembly of the high quality reads resulted in 75,407 contigs of which 3,071 were singletons. A total of 39,425 transcripts were conceptually translated into amino-sequences of which 22,023 matched known proteins in the NCBI non-redundant protein database, 15,839 revealed conserved protein domains through InterPro functional classification and 9,584 were assigned with Gene Ontology terms. Queries conducted within the database enabled the identification of genes putatively involved in immune and inflammatory reactions which had not been previously evidenced in the vent mussel. Their physical counterpart was confirmed by semi-quantitative quantitative Reverse-Transcription-Polymerase Chain Reactions (RT-PCR and their RNA transcription level by quantitative PCR (q