Fin Ray Stiffness and Fin Morphology Control Ribbon-Fin-Based Propulsion.

Science.gov (United States)

Liu, Hanlin; Taylor, Bevan; Curet, Oscar M

2017-06-01

Ribbon-fin-based propulsion has rich locomotor capabilities that can enhance the mobility and performance of underwater vehicles navigating in complex environments. Bony fishes using this type of propulsion send one or multiple traveling waves along an elongated fin with the actuation of highly flexible rays that are interconnected by an elastic membrane. In this work, we study how the use of flexible rays and different morphology can affect the performance of ribbon-fin propulsion. We developed a physical model composed of 15 rays that are interconnected with an elastic membrane. We tested four different ray flexural stiffness and four aspect ratios. The robotic model was tested in a low-turbulence flume under two flow conditions ([Formula: see text] wavelength/s). In two experimental sets, we measured fin kinematics, net surge forces, and power consumption. Using these data, we perform a thrust and power analysis of the undulating fin. We present the thrust coefficient, power coefficient, and propulsive efficiency. We find that the thrust generation was linear with the enclosed area swept by the fin, and square of the relative velocity between the incoming flow and traveling wave. The thrust coefficient levels off around 0.5. In addition, for our parameter range, we find that the power consumption scales by the cube of the effective tangential velocity of the rays [Formula: see text] (A is the amplitude of the ray oscillating motion, and [Formula: see text] is the angular velocity). We show that a decay in stiffness decreases both thrust production and power consumption. However, for rays with high flexural stiffness, the difference in thrust compared with rigid rays is minimal. Moreover, our results show that flexible rays can improve the propulsive efficiency compared with a rigid counterpart. Finally, we find that the morphology of ribbon fin affects its propulsive efficiency. For the aspect ratio considered in our experiments, [Formula: see text] was the most

Transformation de l'économie non structurée depuis la fin du conflit ...

International Development Research Centre (IDRC) Digital Library (Canada)

En 2002, l'Angola émergeait de 40 ans de conflit, l'une des plus longues guerres civiles qu'ait connues l'Afrique. Depuis, le pays est devenu le deuxième plus important producteur de pétrole et le premier fournisseur de la Chine. Cette concentration de l'activité économique dans les secteurs du pétrole et du diamant profite ...

Améliorer le rendement des zones urbaines dans le contexte du ...

International Development Research Centre (IDRC) Digital Library (Canada)

... dans la croissance des entreprises, ainsi que dans la question connexe de ... qu'il appellera l'indice de performance des zones urbaines aux fins de cette analyse. ... privé et l'utilisation efficace des ressources publiques limitées du Kenya.

Mobilisation du financement privé aux fins de l'adaptation | IDRC ...

International Development Research Centre (IDRC) Digital Library (Canada)

Le Private Financing Advisory Network (PFAN) de la Climate Technology Initiative (CTI) réalisera la recherche en collaboration avec la Frankfurt Business School et le réseau actuel du PFAN de la CTI dans les pays d'Afrique subsaharienne ciblés. Les équipes ... International Center for Environmental Technology Transfer.

Heavy sediment influx during early Holocene: Inference from clay mineral studies in a core from the western Bay of Bengal

Digital Repository Service at National Institute of Oceanography (India)

Reddy, N.P.C.; Rao, K.M.

is attributed to heavy sediment influx du r- ing Mid Termination (MT) (12,500 ? 10,000 years BP), due to i n creased precipitation and run - off resulting from high inte n sity monsoonal regime. C LAY minerals are a powerful source for the interpret a... to address to the prov e nance of the sediments in a sediment core from the western Bengal Fan. In this paper, we report clay mi n eralogy and provide an explanation for the heavy sed i ment deposition du r ing the Holocene. A sediment core of 650...

Monothéisme en Arabie du Sud préislamique

Directory of Open Access Journals (Sweden)

Iwona Gajda

2002-04-01

Full Text Available A la fin du IVe siècle de l'ère chrétienne, l'Arabie du Sud abandonne les cultes polythéistes et adopte le monothéisme. Dès lors, les inscriptions monothéistes se multiplient. Un certain nombre d'entre elles sont juives ou judaïsantes alors qu'aucune inscription royale n'est explicitement juive. Cet article présente une courte synthèse de nos connaissances sur le monothéisme en Arabie du Sud avant l'islam. L'accent est mis sur la dimension politique et non uniquement religieuse des conflits du VIe siècle qui opposèrent le roi juif Yûsuf aux Ethiopiens chrétiens essayant de conquérir l'Arabie du Sud et leurs alliées, les chrétiens /himyarites. Le caractère de la religion officielle avant les conflits du VIe siècle est discuté en fin de l'article. L'auteur suggère d'y voir un monothéisme judaïsant plutôt que le judaïsme.Monotheism in pre-Islamic South Arabia. South Arabia abandoned polytheistic cults and adopted monotheism at the end of the 4th century AD, after which time monotheistic inscriptions become more common. Some of these inscriptions are Jewish or `judaizing', although no royal inscription is explicitly Jewish. This article brief summarizes our knowledge of monotheism in pre-Islamic South Arabia, with emphasis on the political, not merely doctrinal, dimensions of the conflicts in the 6th century AD between the Jewish king Yûsuf and the Ethiopian Christians, who were trying to conquer South Arabia, and their Christian allies the Himyarites. The author proposes to interpret as `judaizing' monotheism, rather than Judaism as such, the official religion prior to these 6th century conflicts.

Effect of the Curved Fin Top Edge on the Electrical Characteristics of FinFETs.

Science.gov (United States)

Ahn, Joonsung; Kim, Tae Whan

2018-03-01

The effect of the curved fin top edge on the electrical characteristics of FinFETs was investigated. The curvature radius of the fin top edge for the FinFETs was changed from 0 to 5 nm in order to determine the optimum condition of the electrical characteristics for the devices. The on-current level of the FinFETs with a curvature radius of 5 nm of fin top edge was 24.45% larger than that of the FinFETs with a cuboid fin. The electron current density and the electron mobility of the fin top edge for the FinFETs were larger than those for the FinFETs with a cuboid fin. The electrical characteristics of the FinFETs with a curvature radius of 5 nm for the fin top edge showed the best performance due to the largest expansion of the effective channel region.

Effets du conditionnement en jours longs à la fin du cycle reproducteur sur la période d'ovulation et sur les sécrétions gonadotropes chez l'omble chevalier (Salvelinus alpinus

Directory of Open Access Journals (Sweden)

GILLET C.

1998-07-01

Full Text Available Les ombles chevaliers originaires du Léman se reproduisent à la fin de l'automne. En élevage, il est intéressant de retarder de quelques mois la période des ovulations car ce poisson a besoin d'une température inférieure à 6°C pendant l'ovulation. Il est plus facile de fournir une eau à cette température aux géniteurs retardés qui ovulent en hiver qu'à ceux qui ovulent naturellement en automne. Le conditionnement des ombles chevaliers en jours longs (17L-7N pendant l'automne permet de retarder de plusieurs mois la période des ovulations. Cette méthode a l'inconvénient de provoquer un étalement des ovulations sur plus de 3 mois. Le reconditionnement des géniteurs en jours courts en décembre supprime ce problème. L'efficacité du traitement en jours longs ne semble pas dépendre de la durée de son application pourvu que celle-ci dépasse 1,5 mois. Chez les femelles conditionnées en jours longs en automne et en hiver, les concentrations en gonadotropine plasmatique (GTH II sont très faibles. Le niveau de la GTH II plasmatique augmente trois semaines après un transfert en jours courts en janvier. Les concentrations de la GTH II plasmatique au cours de l'ovulation sont significativement plus faibles chez les femelles conditionnées en jours longs en janvier que chez les animaux reconditionnés en jours courts. A ce stade du cycle reproducteur, la GTH I plasmatique reste toujours à un niveau très faible, quel que soit le régime photopériodique. La pose d'implant de mélatonine chez les poissons ne modifie pas les sécrétions gonadotropes en jours longs comme en jours courts. La réceptivité hypophysaire des femelles à une stimulation de la sécrétion gonadotrope par une injection de GnRH n'est pas modifiée par le conditionnement des poissons en jours longs. Aucun effet du pimozide sur la sécrétion de la GTH II n'a pu être mis en évidence chez les géniteurs conditionnés en jours longs. Ces résultats permettent

Numerical Analysis of Aerodynamic Characteristics of the Finned Surfaces with Cross-inclined Fins

Directory of Open Access Journals (Sweden)

Lagutin A. E.

2016-12-01

Full Text Available This paper presents results of numerical research and analyses air-side hydraulic performance of tube bundles with cross inclined fins. The numerical simulation of the fin-tube heat exchanger was performed using the Comsol Femlab software. The results of modeling show the influence of fin inclination angle and tube pitch on hydraulic characteristics of finned surfaces. A series of numerical tests were carried out for tube bundles with different inclination angles (γ =900, 850, 650, 60, the fin pitch u=4 mm. The results indicate that tube bundles with cross inclined fins can significantly enhance the average integral value of the air flow rate in channel between fins in comparison with conventional straight fins. Aerodynamic processes on both sides of modificated channel between inclined fins were analyzed. The verification procedures for received results of numerical modeling with experimental data were performed.

Study of the behaviour of organic carbon in the soil, and carbon 14 study of podzols; Contribution a l'etude du comportement du carbone organique dans le sol et etude des podzols a l'aide du carbone 14

Energy Technology Data Exchange (ETDEWEB)

Nakhla Shawki, M [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires

1969-07-01

Using the penetration into soil of carbon 14 of thermo-nuclear origin, the behaviour and renewal rate were studied on different organic fractions of the soil. It was established that 18% of the total organic matter is renewed in about 400 years. In addition the formation of podzol-type fossil soils in France was dated from the first millenary B.C., i.e. the end of the sub-boreal period and the beginning of the atlantic period. (author) [French] En utilisant la penetration dans le sol du carbone 14 d'origine thermonucleaire, on a etudie le comportement et la vitesse de renouvellement des differentes fractions de la matiere organique du sol. On a pu preciser que 18% de la matiere organique globale se renouvelait en 400 ans environ. Par ailleurs, la formation en France des sols fossiles du type podzol a ete datee du premier millenaire avant J.C. c'est a dire a la fin de la periode subboreale et au debut de la periode atlantique. (auteur)

La redécouverte du droit : le trajet parcouru

NARCIS (Netherlands)

Hesseling, G.S.C.M.; Oomen, B.M.

2005-01-01

Au Mali, l'année 1991 marque la fin du régime autoritaire de la IIe République et le début d'une ère plus démocratique. En février 1993 est votée la loi-cadre sur la décentralisation. Au moment où, en 2001, les premiers juristes commencent leur aventure de recherche - qui aboutira à l'ouvrage

Frost behavior of a fin surface with temperature variation along heat exchanger fins

International Nuclear Information System (INIS)

Kim, Jung Soo; Kim, Min Soo; Lee, Kwan Soo; Kim, Ook Joong

2007-01-01

This paper presents a mathematical model for predicting the frost behavior formed on heat exchanger fins, considering fin heat conduction under frosting condition. The model is composed of air-side, the frost layer, and fin region, and they are coupled to the frost layer. The frost behavior is more accurately predicted with fin heat conduction considered (Case A) than with a constant fin surface temperature assumed (Case B). The results indicate that the frost thickness and heat transfer rate for Case B are over-predicted in most regions of the fin, as compared to those for Case A. Also, for Case A, the maximum frost thickness varies little with the fin length variations, and the extension of the fin length over 30 mm contributes insignificantly to heat transfer

Étude de délimitation aux fins de l'Initiative régionale pour la lutte ...

International Development Research Centre (IDRC) Digital Library (Canada)

Étude de délimitation aux fins de l'Initiative régionale pour la lutte contre le tabac en Afrique. Financée par le CRDI et la Fondation Bill et Melinda Gates, l'initiative Analyses situationnelles de la lutte antitabac en Afrique (ASTA) a pour objectif de permettre de comprendre les facteurs déterminants du succès de la lutte ...

La réaction des pays d'Islam face aux Croisades et aux États latins, fin du XIe - milieu du XIIIe siècle

OpenAIRE

Van Renterghem , Vanessa

2000-01-01

Cet article, rédigé à l'occasion de la question d'agrégation d'histoire portant sur " Les relations entre les pays d'Islam et le monde latin du milieu du Xe au milieu du XIIIe siècle " (2000-2002), examine différents aspects des relations entre Croisés et musulmans, vues des pays d'Islam. Il s'intéresse tout d'abord à l'évolution de l'image des Croisés dans les sources arabes de l'époque ainsi qu'au sort des musulmans sous domination franque. Il retrace ensuite les différentes étapes de la ré...

A biorobotic model of the sunfish pectoral fin for investigations of fin sensorimotor control

International Nuclear Information System (INIS)

Phelan, Chris; Tangorra, James; Lauder, George; Hale, Melina

2010-01-01

A comprehensive understanding of the control of flexible fins is fundamental to engineering underwater vehicles that perform like fish, since it is the fins that produce forces which control the fish's motion. However, little is known about the fin's sensory system or about how fish use sensory information to modulate the fin and to control propulsive forces. As part of a research program that involves neuromechanical and behavioral studies of the sunfish pectoral fin, a biorobotic model of the pectoral fin and of the fin's sensorimotor system was developed and used to investigate relationships between sensory information, fin ray motions and propulsive forces. This robotic fin is able to generate the motions and forces of the biological fin during steady swimming and turn maneuvers, and is instrumented with a relatively small set of sensors that represent the biological lateral line and receptors hypothesized to exist intrinsic to the pectoral fin. Results support the idea that fin ray curvature, and the pressure in the flow along the wall that represents the fish body, capture time-varying characteristics of the magnitude and direction of the force created throughout a fin beat. However, none of the sensor modalities alone are sufficient to predict the propulsive force. Knowledge of the time-varying force vector with sufficient detail for the closed-loop control of fin ray motion will result from the integration of characteristics of many sensor modalities.

A biorobotic model of the sunfish pectoral fin for investigations of fin sensorimotor control

Energy Technology Data Exchange (ETDEWEB)

Phelan, Chris; Tangorra, James [Department of Mechanical Engineering, Drexel University, Philadelphia, PA 19104 (United States); Lauder, George [Museum of Comparative Zoology, Harvard University, Cambridge, MA 02138 (United States); Hale, Melina, E-mail: tangorra@coe.drexel.ed [Department of Organismal Biology and Anatomy, University of Chicago, Chicago, IL 60637 (United States)

2010-09-15

A comprehensive understanding of the control of flexible fins is fundamental to engineering underwater vehicles that perform like fish, since it is the fins that produce forces which control the fish's motion. However, little is known about the fin's sensory system or about how fish use sensory information to modulate the fin and to control propulsive forces. As part of a research program that involves neuromechanical and behavioral studies of the sunfish pectoral fin, a biorobotic model of the pectoral fin and of the fin's sensorimotor system was developed and used to investigate relationships between sensory information, fin ray motions and propulsive forces. This robotic fin is able to generate the motions and forces of the biological fin during steady swimming and turn maneuvers, and is instrumented with a relatively small set of sensors that represent the biological lateral line and receptors hypothesized to exist intrinsic to the pectoral fin. Results support the idea that fin ray curvature, and the pressure in the flow along the wall that represents the fish body, capture time-varying characteristics of the magnitude and direction of the force created throughout a fin beat. However, none of the sensor modalities alone are sufficient to predict the propulsive force. Knowledge of the time-varying force vector with sufficient detail for the closed-loop control of fin ray motion will result from the integration of characteristics of many sensor modalities.

Mise en place de services de conseil et de dépistage volontaire du ...

International Development Research Centre (IDRC) Digital Library (Canada)

intention des couples à Durban à des fins de prévention et d'intervention. Les couples hétérosexuels constituent le plus grand groupe à risque d'infection par le VIH en Afrique subsaharienne. Les services de conseil et de dépistage volontaire du ...

Sodome à Paris : protohistoire de l’homosexualité masculine, fin XVIII– milieu XIXe siècle

Directory of Open Access Journals (Sweden)

Thierry Pastorello

2009-07-01

Full Text Available Alain Corbin, dans une étude intitulée L’Harmonie des plaisirs : les manières de jouir du siècle des lumières à l’avènement de la sexologie, note en ce qui concerne la période étudiée l’obligation d’oublier les concepts forgés par la sexologie. Pourtant, si la construction de l’homosexualité ne peut être envisagée avant la fin du XIXe siècle, les sentiments dits homosexuels furent antérieurement perçus à travers certains critères. Les hommes pratiquant ces rapports affectifs et sexuels eurent...

Methylmercury in dried shark fins and shark fin soup from American restaurants.

Science.gov (United States)

Nalluri, Deepthi; Baumann, Zofia; Abercrombie, Debra L; Chapman, Demian D; Hammerschmidt, Chad R; Fisher, Nicholas S

2014-10-15

Consumption of meat from large predatory sharks exposes human consumers to high levels of toxic monomethylmercury (MMHg). There also have been claims that shark fins, and hence the Asian delicacy shark fin soup, contain harmful levels of neurotoxic chemicals in combination with MMHg, although concentrations of MMHg in shark fins are unknown. We measured MMHg in dried, unprocessed fins (n=50) of 13 shark species that occur in the international trade of dried shark fins as well as 50 samples of shark fin soup prepared by restaurants from around the United States. Concentrations of MMHg in fins ranged from 9 to 1720 ng/g dry wt. MMHg in shark fin soup ranged from sharks such as hammerheads (Sphyrna spp.). Consumption of a 240 mL bowl of shark fin soup containing the average concentration of MMHg (4.6 ng/mL) would result in a dose of 1.1 μg MMHg, which is 16% of the U.S. EPA's reference dose (0.1 μg MMHg per 1 kg per day in adults) of 7.4 μg per day for a 74 kg person. If consumed, the soup containing the highest measured MMHg concentration would exceed the reference dose by 17%. While shark fin soup represents a potentially important source of MMHg to human consumers, other seafood products, particularly the flesh of apex marine predators, contain much higher MMHg concentrations and can result in substantially greater exposures of this contaminant for people. Copyright © 2014 Elsevier B.V. All rights reserved.

50 CFR 600.1204 - Shark finning; possession at sea and landing of shark fins.

Science.gov (United States)

2010-10-01

... 50 Wildlife and Fisheries 8 2010-10-01 2010-10-01 false Shark finning; possession at sea and landing of shark fins. 600.1204 Section 600.1204 Wildlife and Fisheries FISHERY CONSERVATION AND... PROVISIONS Shark Finning § 600.1204 Shark finning; possession at sea and landing of shark fins. (a)(1) No...

Experimental study of heat transfer and pressures drops for cans with spiral herring-bone fins; Etude experimentale du transfert de chaleur et des pertes de charges des gaines a ailettes helicoidales en chevron

Energy Technology Data Exchange (ETDEWEB)

Pelce, J; Francois, S; Houseaux, O; Pierre, B [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires

1964-07-01

Cans fitted with herring-bone fins are used for cooling uranium in certain nuclear reactor. By herring-bone is meant a staggered arrangement of the fins which have a plane of symmetry parallel to the general direction of liquid flow. The main geometrical parameter are then: the number of fins, the number of herring-bones, the angle of inclination of the fins with respect to the can axis, the dimensions of the fins, the can diameter and the channel diameter. The research is essentially experimental. The test are of three types: full size tests, in conditions approaching those in the reactor (constant flux, CO{sub 2} under pressure); full size tests but with a constant wall temperature, much easier to set up, and intended to distinguish rapidly between the merits of the various types of can; large-scale tests with air at atmospheric pressure for studying the phenomena in more detail. For each can tried out there is a corresponding pressure drop coefficient, a mean thermal exchange coefficient Mo-bar and a minimum exchange coefficient Mo{sub min} and Mo-bar are related by the expression Mo{sub min} = Mo-bar * f{sub c} * f, where f{sub c} and f are respectively circumferential and longitudinal singularity factor determined from a statistical study of all the temperatures measured for each can. The results are presented in about thirty tables and figures the most noteworthy results being summarized in the conclusion. (authors) [French] Les gaines a ailettes en chevron sont utilisees pour le refroidissement de l'uranium dans certains reacteurs nucleaires. Par chevron, on entend une disposition alternee des ailettes ayant un plan de symetrie parallele a la direction generale de l'ecoulement fluide. Les principaux parametres geometriques sont alors: le nombre des ailettes, le nombre de chevrons, l'angle d'inclinaison des ailettes par rapport a l'axe de la gaine, les dimensions des ailettes, le diametre de la gaine et le diametre du canal. L'etude est essentiellement

Guide d’indexation des travaux de fin d’étude en médecine générale

OpenAIRE

Jamoulle, Marc

2017-01-01

Le Centre de Coordination Francophone pour la Formation en Médecine Générale (CCFFMG) (www.ccffmg.be) a été chargé d’organiser la mise en ligne publique des Travaux de Fin d’Étude (TFE). Le TFE est réalisé à la fin du master de spécialité des départements de médecine générale de l’Université Libre de Bruxelles (ULB), l’Université Catholique de Louvain (UCL) et Université de Liège (ULg). Un site dédié (www.mgtfe.be) propose un guide de rédaction en ligne. Ce site offre aussi la description et ...

IntroductionLa parole des rois à la fin du Moyen Âge : les voies d’une enquête

Directory of Open Access Journals (Sweden)

Stéphane PÉQUIGNOT

2007-10-01

Full Text Available El artículo sugiere algunas propuestas para una investigación general sobre el hablar de los reyes a finales de la Edad Media. Basándose en un estado de la cuestión para el caso de la Corona de Aragón, se indaga la inscripción del hablar de los reyes en distintas temporalidades imbricadas entre sí. La transcripción de las palabras resulta de un proceso complejo, la « fábrica de la palabra », cuyos mecanismos y huellas son objeto de estudio. Por otra parte, las representaciones del hablar de los reyes hacen a menudo referencia a unos modelos traídos del pasado, a veces se dirigen a un público futuro, mientras testimonian también su necesaria adaptación a las circunstancias de cada momento. Estos « actas reales de palabra », así como los « estilos expresivos » que contribuyen a forjar, se examinan en la secunda parte del artículo. Finalmente, el tiempo dedicado o dejado a las palabras reales participa de las evoluciones a largo plazo de las relaciones a lo escrito, de los regímenes políticos y de su forma de legitimación ; constituye un modo de comunicación político importante, un recurso y, también, una toma de riesgo para el poder y la autoridad monarquica.L’article invite à une enquête générale sur la parole des rois à la fin du Moyen Âge et en esquisse plusieurs voies possibles. À l’aide d’un état de la question sur la couronne d’Aragon, c’est l’inscription de la parole des rois dans différentes temporalités imbriquées qui est visée. Sa transcription même résulte d’un processus complexe, la « fabrique de la parole », dont mécanismes et traces sont examinés. D’autre part, les représentations de la parole des rois renvoient souvent à des modèles du passé, visent parfois un public futur tout en témoignant aussi d’une nécessaire adaptation aux circonstances présentes. Ces « actes royaux de parole » et les « styles expressifs » qu’ils contribuent à consolider

Effects of ultra-thin Si-fin body widths upon SOI PMOS FinFETs

Science.gov (United States)

Liaw, Yue-Gie; Chen, Chii-Wen; Liao, Wen-Shiang; Wang, Mu-Chun; Zou, Xuecheng

2018-05-01

Nano-node tri-gate FinFET devices have been developed after integrating a 14 Å nitrided gate oxide upon the silicon-on-insulator (SOI) wafers established on an advanced CMOS logic platform. These vertical double gate (FinFET) devices with ultra-thin silicon fin (Si-fin) widths ranging from 27 nm to 17 nm and gate length down to 30 nm have been successfully developed with a 193 nm scanner lithography tool. Combining the cobalt fully silicidation and the CESL strain technology beneficial for PMOS FinFETs was incorporated into this work. Detailed analyses of Id-Vg characteristics, threshold voltage (Vt), and drain-induced barrier lowering (DIBL) illustrate that the thinnest 17 nm Si-fin width FinFET exhibits the best gate controllability due to its better suppression of short channel effect (SCE). However, higher source/drain resistance (RSD), channel mobility degradation due to dry etch steps, or “current crowding effect” will slightly limit its transconductance (Gm) and drive current.

Entretien avec M. Bernard Dormy, Président du TREF, courant novembre 2017

CERN Multimedia

Staff Association

2018-01-01

M. Bernard Dormy, Président du TREF (Tripartite Employment Conditions Forum) (voir Echo n° 242) a terminé son mandat à la fin de l'année 2017. L’Association du personnel a souhaité s’entretenir avec lui sur le CERN et son personnel et, entre autres, sur le modèle de concertation. Cette publication est également l’occasion pour l’Association du personnel de saluer M. Dormy pour l’engagement dont il a fait preuve depuis 2003, année où il a débuté au TREF comme délégué français. Il faut croire que son mandat au sein de ce forum lui a particulièrement plu, puisque M. Dormy a occupé les fonctions de Vice-président du TREF de 2007 à 2011, puis de Président de 2012 à 2017. Sous sa prési...

FinTech in Norway : the effect of FinTech on the traditional Norwegian banking sector

OpenAIRE

Omreng, Stian; Gjendem, Ida

2017-01-01

The purpose of this thesis is to investigate the effect of FinTech on the Norwegian banking industry. We investigate the drivers of FinTech, the current and potential Norwegian FinTech market, and the international competitiveness of the Norwegian FinTech movement. We identify nine segments of FinTech within the traditional banking functions Financing, Asset management, Payments and Authentication, and we find the key drivers behind the rapid growth of the FinTech market as cha...

Performance study of a fin and tube heat exchanger with different fin geometry

DEFF Research Database (Denmark)

Singh, Shobhana; Sørensen, Kim; Condra, Thomas Joseph

2016-01-01

This study analyses the effect of different fin geometries on the heat transfer and pressure loss characteristics of a fin and tube heat exchanger. A numerical investigation is carried out on liquid–gas type double-finned tube heat exchanger under cross-flow condition. Three different cross......-sections namely: a) Rectangular, b) Trapezoidal, c) Triangular are adopted to define the fin geometry. The CFD simulations are performed to incorporate coupled steady state conjugate heat transfer with the turbulent flow phenomenon for the Reynolds number in the range of 5000-13000. Dimensionless heat transfer...... models show that triangular fin geometry can provide higher heat transfer performance in comparison to the fins with rectangular and trapezoidal geometry with lower pressure loss and a bonus of 7.27% reduction in weight under similar operating conditions....

Flow and Mass Transfer Performance in Short Pin-Fin Channels with Different Fin Shapes

OpenAIRE

Goldstein, R. J.; Chen, S. B.

1998-01-01

The mass transfer (analogous to heat transfer) and pressure loss characteristics of staggered short pin-fin arrays are investigated experimentally in the range of Reynolds number 3000 to 18,000 based on fin diameter and mean approach-flow velocity. Three different shapes of fins with aspect ratio of 2 are examined: one uniform-diameter circular fin (UDCF) and two stepped-diameter circular fins (SDCF1 and SDCF2). Flow visualization using oil-lampblack reveals complex flow characteristics assoc...

De Paris à Lyon. Les mutations éditoriales du «Lancelot du Lac»

Directory of Open Access Journals (Sweden)

Gaëlle Burg

2015-07-01

Full Text Available Lancelot du Lac est le premier roman arthurien imprimé à la Renais­sance. Dans sa première édition parue en 1488, qui réunit deux imprimeurs (Jean Le Bourgeois à Rouen et Jean Du Pré à Paris, un découpage et un prologue inédits sont ajoutés par le remanieur. Le texte sera réédité six fois par divers imprimeurs-libraires parisiens jusqu’en 1533. L’édition de luxe d’Antoine Vérard (1494, destinée au roi Charles VIII, présente d’importantes modifications effectuées dans un but commercial. Après une longue période d’accalmie qui signe le début du déclin de la vogue des romans de chevalerie médiévaux, Benoît Rigaud publie à Lyon, sous une forme considérablement abrégée, la dernière édition connue du Lancelot au XVIe siècle (1591. Si elle ne présente que peu d’intérêt littéraire, elle apporte cependant des informations concernant les pratiques éditoriales et les goûts du  lecteur de la fin du XVIe siècle. De Paris à Lyon, entre renaissance et déclin, le parcours éditorial d’un incontournable roman arthurien.Lancelot du Lac is the editio princeps of an Arthurian romance in Renaissance France. The first edition in 1488, which brings together two printers (Jean Le Bourgeois from Rouen and Jean Du Pré from Paris, offers original arrangement and prologue added by the compositor. The text will be published six times by various printers and booksellers in Paris until 1533. The luxurious edition from Antoine Vérard (1494 dedicated to King Charles VIII provides interesting transformations in commercial purposes. After a long time without edition, showing the beginning of chivalry literature’s decline, Benoît Rigaud publish in Lyon, in a greatly abbreviated form, the last known edition of Lancelot in the XVIth century (1591. If it presents no literary interest, it provides nevertheless informations about editorial practices and reader’s tastes from the end of Renaissance France. From Paris to

Novel 14-nm Scallop-Shaped FinFETs (S-FinFETs) on Bulk-Si Substrate

OpenAIRE

Xu, Weijia; Yin, Huaxiang; Ma, Xiaolong; Hong, Peizhen; Xu, Miao; Meng, Lingkuan

2015-01-01

In this study, novel p-type scallop-shaped fin field-effect transistors (S-FinFETs) are fabricated using an all-last high-k/metal gate (HKMG) process on bulk-silicon (Si) substrates for the first time. In combination with the structure advantage of conventional Si nanowires, the proposed S-FinFETs provide better electrostatic integrity in the channels than normal bulk-Si FinFETs or tri-gate devices with rectangular or trapezoidal fins. It is due to formation of quasi-surrounding gate electrod...

Recherche pour le développement — Afrique du Sud | IDRC ...

International Development Research Centre (IDRC) Digital Library (Canada)

11 janv. 2011 ... À la fin de 1985, les dirigeants et le personnel du CRDI sont devenus les fers de lance d'une campagne d'envergure, très bien structurée, visant à recueillir les données qui permettraient d'analyser la situation. Ce travail a donné lieu quelque trois ans plus tard à un programme d'aide à la recherche pour le ...

L’enjeu du régionalisme dans les relations entre les pays émergents. Le cas du Brésil et de l’Afrique du Sud

Directory of Open Access Journals (Sweden)

Audrey Lauriello

2011-01-01

Full Text Available La présente contribution se penche sur la place accordée au régionalisme dans les relations entre les pays dits «émergents» que sont le Brésil et l’Afrique du Sud. La dernière décennie a vu apparaître de nouvelles puissances qui entendent participer à l’édiction des règles régissant le comportement des États sur la scène internationale au même titre que les grandes puissances industrielles traditionnelles. À cette fin, le Brésil et l’Afrique du Sud notamment ont développé une diplomatie active et multi-niveaux et s’accordent mutuellement davantage de place dans leur agenda extérieur. Parmi les différents instruments – bilatéraux, régionaux, et multilatéraux – qu’ils mobilisent, la relation interrégionale apparaît comme un outil parmi d’autres qui vise avant tout à concrétiser leurs aspirations plus globales.

Santé et hygiénisme dans les villes du canal de Suez (fin XIXe-1ère moitié du XXe siècle)

OpenAIRE

Frémaux, Céline

2008-01-01

Cet article identifie, à partir des archives de la Compagnie du canal de Suez, les problématiques qui ont favorisé l'émergence de figures de la santé dans les villes qui se sont développées sur les rives du canal de Suez. Il analyse les solutions mises en œuvre par les acteurs de la planification urbaine et de la construction, en lien avec les doctrines hygiénistes développées en Europe.

La figure héroïque d’Alexandre le Grand en Espagne à la fin du Moyen Âge comme modèle du rapport à l’étranger. El Libro Ultramarino et El Libro de las maravillas de Jean de Mandeville (XIVe et XVe siècles

Directory of Open Access Journals (Sweden)

Julia Roumier

2013-06-01

Full Text Available Déjà riche d’une longue tradition scripturaire, le cycle d’Alexandre jouit d’un regain d’intérêt à la fin du Moyen Âge qui lui apporte de nouveaux éclairages. En témoignent deux traductions hispaniques : le récit de voyages de Jean de Mandeville, traduit en aragonais vers 1380 et en castillan à la fin du XVe siècle, et la description de l’Orient de Jacques de Vitry, traduite en castillan vers 1360. Elles contiennent quelques épisodes-clefs de l’aventure orientale d’Alexandre qui offrent une représentation symbolique des rapports conflictuels de l’Orient et de l’Occident, mais aussi la possibilité d’interroger les valeurs morales de l’Occident chrétien. L’enfermement de Gog et Magog, assimilés aux dix tribus perdues d’Israël à partir du XIIe siècle, intègre Alexandre à l’eschatologie chrétienne. Sa correspondance fictive avec les Brahmanes offre la description d’une société utopique qui remplit une fonction critique face aux mœurs corrompues des Chrétiens.Tras una larga tradición textual, el interés renovado por el ciclo de Alejandro a finales de la Edad Media conlleva nuevas interpretaciones. Lo ilustran dos traducciones hispánicas de finales del siglo XIV. El relato de viajes de Juan de Mandevilla, traducido al aragonés hacia 1380 y al castellano a finales del siglo XV, y la descripción de Oriente por Jacobo de Vitry, traducida al castellano hacia 1360, presentan unos episodios claves de la aventura oriental de Alejandro. Ofrecen la representación simbólica de las relaciones conflictivas entre Oriente y Occidente así como la posibilidad de cuestionar los valores morales del Occidente cristiano. El encierro de Gog y Magog, pueblos asimilados a las diez tribus perdidas de Israel a partir del siglo XII, convierte a Alejandro en actor de la escatología cristiana. Su correspondencia ficticia con los Brahmanes presenta la descripción de una sociedad utópica que desempeña una

Investigation of material efficient fin patterns for cost-effective operation of fin and tube heat exchanger

DEFF Research Database (Denmark)

Singh, Shobhana; Sørensen, Kim; Condra, Thomas Joseph

2017-01-01

Design management of a thermal energy system is a critical part of identifying basic designs that meet large scale user demand under certain operating characteristics. Fin and tube heat exchangers are among the most commonly used thermal energy systems which are generating considerable interest...... and tube heat exchanger. Computational fluid dynamic models of fin and tube heat exchanger with different fin patterns are developed to investigate the fin pattern behavior on heat transfer and pressure loss performance data. In addition, the numerical results are utilized to analyze the engineering design...... scale-up heat exchanger configurations with each fin pattern focusing on the application of chosen fin and tube heat exchanger in marine exhaust gas boiler. The analysis highlights the impact of material efficient fin patterns investigated and predicts that the polynomial and sinusoidal fin patterns...

La dimension publicitaire du storytelling politique

Directory of Open Access Journals (Sweden)

Andreea Monica State

2016-11-01

Full Text Available Le thème général de cet article fait référence à la dimension publicitaire de la narration politique. J'ai choisi ce sujet parce que les histoires font partie de la vie humaine depuis longtemps, utilisées pour transmettre la tradition et enseigner des modèles de comportement social. Récemment, des histoires ont été utilisées de plus en plus souvent à des fins diverses telles que la publicité, la gestion ou la politique. Cet article vise à réaliser une recherche qualitative qui combine l'analyse du contenu et l'analyse du discours. En dehors de la base théorique qui vise à clarifier les concepts de base de la recherche, j’étudie la narration politique utilisée par l'ancien Président Traian Basescu et l'ancien Premier Ministre Victor Ponta dans les biographies en ligne, puis une analyse de leurs discours lors de la Fête Nationale de la Roumanie et l'Union des Principautés Roumaines.

Studi Analitik dan Numerik Perpindahan Panas pada Fin Trapesium (Studi Kasus pada Finned Tube Heat Exchanger

Directory of Open Access Journals (Sweden)

Ahmad Zaini

2013-09-01

Full Text Available Penambahan fin pada pipa penukar kalor merupakan suatu upaya memperbesar perpindahan kalor konduksi dan konveksi, dengan cara memperluas bidang geometri. Pada penelitian ini dianalisa secara analitik dan numerik perpindahan kalor pada fin dengan profil longitudinal tidak seragam atau berubah terhadap jarak dari dasar fin, dengan memvariasikan ketebalan ujung fin. Hasil dari kedua studi ini tidak jauh berbeda, pada keduanya menjelaskan bahwa fin dengan ketebalan ujung 0,9 mm (fin trapesium terbalik paling baik dari 5 variasi lainnya; serta perubahan temperatur paling besar terjadi pada sepertiga pertama dari panjang  fin, ini artinya pelepasan kalor terbesar terjadi pada daerah tersebut. Perbedaannya adalah pada persentase penurunan temperatur sepanjang  fin terhadap temperatur dasar fin, untuk ketebalan 0,9 mm pada studi analitik sebesar 91,92% dan pada studi numerik sebesar 91,78%. Hal ini berarti metode penyelesaian persamaan diferensial orde 2 dengan koefisien variabel dengan cara pembedahan koefisien variabel pada ODE, sudah benar dan valid. Namun bila ditinjau dari waktu yang diperlukan untuk komputasinya, studi analitik membutuhkan waktu lebih lama. Waktu yang diperlukan dalam komputasinya tergantung dari fungsi koefisien variabel.

Les accidents, fléaux méconnus en agriculture. De la solidarité facultative à la solidarité obligatoire : pour une histoire sociale du monde agricole

OpenAIRE

Michard, Claire-Élise

2008-01-01

À la fin du 19e siècle, un grand pas s’accomplit en matière d’accidents du travail. Toutefois, la loi du 9 avril 1898 protège les travailleurs de l’industrie, mais non pas ceux de l’agriculture. Cette situation résulte de causes diverses. L’agriculture est alors un secteur protégé par des hommes politiques qui ont besoin du vote et du soutien rural pour appuyer la République naissante. Les agriculteurs et leurs familles peuvent s’assurer contre les conséquences des accidents auprès de la Mutu...

Une masculinité en crise à la fin du XVIIe siècle ? La critique de l'efféminé chez La Bruyère

Directory of Open Access Journals (Sweden)

Cédric Corgnet

2008-07-01

Full Text Available L’efféminé est toujours un cas sexuel limite : homme aux airs féminins, il interroge l’innée de la nature sexuelle, critique les genres et leur définition explicitement physique. La fin du XVIIe siècle illustre cette tension chez les moralistes français et surtout chez La Bruyère dans ses Caractères où celui-ci interroge cette monstruosité générique à travers une analyse sémiologique. Mais cette tératologie n’est pas avant tout clinique mais sociale et morale : il nous avertit, par cet écart de genre, d’une corruption morale du monde tant par une sémiologie clinique que mythologique ovidienne ne cherchant pas le réalisme pathologique mais la filiation antique qui ante son ouvrage sur les Caractères Théophrastiens : philosophe plus que naturaliste.The effeminate is always a sexual limit case: man in the feminine sights, he questions the innate of the sexual nature, criticizes genders and their explicitly physical definition. The end of the XVIIth century illustrates this tension at the French moralists and especially in La Bruyère’s Characters where this one questions this generic monstrousness through a semiological analysis. But this teratology is not above all clinical but social and moral: he warns us, by this distance from gender, from a moral corruption of the world both by a clinical semiology and ovidian mythology not looking for the pathological realism but the antic filiation with Theophrast’s Characters : philosopher more than naturalist.

Toward quantum FinFET

CERN Document Server

Wang, Zhiming

2013-01-01

This book reviews a range of quantum phenomena in novel nanoscale transistors called FinFETs, including quantized conductance of 1D transport, single electron effect, tunneling transport, etc. The goal is to create a fundamental bridge between quantum FinFET and nanotechnology to stimulate readers' interest in developing new types of semiconductor technology. Although the rapid development of micro-nano fabrication is driving the MOSFET downscaling trend that is evolving from planar channel to nonplanar FinFET, silicon-based CMOS technology is expected to face fundamental limits in the near future. Therefore, new types of nanoscale devices are being investigated aggressively to take advantage of the quantum effect in carrier transport. The quantum confinement effect of FinFET at room temperatures was reported following the breakthrough to sub-10nm scale technology in silicon nanowires. With chapters written by leading scientists throughout the world, Toward Quantum FinFET provides a comprehensive introductio...

EQUILIBRE GLYCEMIQUE ET COMPLICATIONS MACROANGIOPATHIQUES DU DIABETE

Directory of Open Access Journals (Sweden)

Lyse BORDIER

2017-05-01

Full Text Available La question de l’efficacité d’un équilibre glycémique optimal dans la prévention des complications macroangiopathiques du diabète a fait l’objet d’une récente polémique. Si les faits sont clairs pour la microangiopathie notamment au cours du diabète de type 1, ils paraissent moins certains pour les complications cardiovasculaires du diabète de type 2. Cette constatation vient de l’intrication des autres facteurs de risque cardiovasculaires qui sont très fréquents chez ces patients. Cependant, les études de suivi sur une longue durée s’inscrivent en faveur de l’intérêt d’un bon équilibre glycémique sur les complications macroangiopathiques. Les résultats négatifs sur la mortalité de l’étude ACCORD et les inquiétudes concernant la rosiglitazone ont conduit à la mise en place d’études sur la sécurité d’utilisation des nouvelles molécules. Tous ces travaux ont abouti à la démonstration de l’absence de risque des iDPP-4 et de l’effet très positif de certaines molécules de la classe des analogues du GLP-1 et des iSGLT2.Il reste à espérer que la récente mise au point de l’Académie de Médecine soulignant que les complications du diabète de type 2 exigent une prévention multifactorielle qui passe obligatoirement par un contrôle optimisé de l'équilibre glycémique mette fin à une polémique inutile et dangereuse pour nos malades.

PHASE CHANGE AROUND A FINNED TUBE

Directory of Open Access Journals (Sweden)

Aytunç EREK

2003-01-01

Full Text Available This study presents the heat transfer enhancement in the thermal energy storage system by using radially finned tube. The solution of the system consists of the solving the equations of the heat transfer fluid (HTF, the pipe wall and fin, and the phase change material (PCM as one domain. The control volume finite difference approach and the semi implicit solver (SIS are used to solve the equations. Fully developed velocity distribution is taken in the HTF. Flow parameters (Re number and inlet temperature of coolant and fin parameters (the number of fins, fin length, fin thickness are found to influence solidification fronts and the total stored energy.

Les Cabinets de curiosités dauphinois dans les origines scientifiques du Muséum d'histoire naturelle de Grenoble (XVIII e -XIX e siècles)

OpenAIRE

Rochas , Joëlle

2008-01-01

Les actes du colloque de Poitiers concernant les cabinets de curiosités seront déposés sur le site web www.curiositas.org, site européen dédié aux cabinets de curiosités (Université de Poitiers).; Le Cabinet d'histoire naturelle de Grenoble, ancêtre du Muséum actuel, a été créé en 1773. Un premier historique de la fin du XVIIIe siècle mentionne les trois principaux cabinets d'où il était issu : un cabinet dauphinois - celui des Antonins - et deux cabinets grenoblois - celui du négociant greno...

Channels with Different Fin Shapes

Directory of Open Access Journals (Sweden)

R. J. Goldstein

1998-01-01

Full Text Available The mass transfer (analogous to heat transfer and pressure loss characteristics of staggered short pin-fin arrays are investigated experimentally in the range of Reynolds number 3000 to 18,000 based on fin diameter and mean approach-flow velocity. Three different shapes of fins with aspect ratio of 2 are examined: one uniform-diameter circular fin (UDCF and two stepped-diameter circular fins (SDCF1 and SDCF2. Flow visualization using oil-lampblack reveals complex flow characteristics associated with the repeated production of horseshoe vortices and fin wakes, and the interactions among these. The SDCF1 and SDCF2 arrays show flow characteristics different from the UDCF array due to downflow from the steps. For all arrays tested, the near-endwall flow varies row by row in the initial rows until it reaches a stable pattern after the third row. The row-averaged Sherwood numbers obtained from the naphthalene sublimation experiment also show a row-by-row variation pattern similar to the flow results. While the SDCF2 array has the highest mass transfer rate, the SDCF1 array has the smallest pressure loss at the same approach-flow velocity. The fin surfaces have higher array-averaged Sherwood number than the endwall and the ratio between these changes with fin shape and Reynolds number. The performance of the pin-fin arrays is analyzed under two different constraints: the mass[heat transfer rate at fixed pumping power, and the mass/heat transfer area and pressure loss to fulfill fixed heat load at a fixed mass flow rate. In both cases, the SDCF2 array shows the best performance.

L’industrie du luxe et la mode : du temps des créateurs au temps des communicants (fin XIXe, fin XXe siècle

Directory of Open Access Journals (Sweden)

Marc de Ferrière le Vayer

2007-05-01

Full Text Available En un siècle, le secteur de la mode en France a connu un profond bouleversement. D’un monde artisanal doté d’un grand savoir-faire, on est passé progressivement à une activité de grande production s’adressant à un marché de plus en plus large. Ainsi, les grands créateurs, tant dans la haute couture que dans le parfum, ont progressivement été remplacés par des designers touche à tout. Le marketing et la publicité deviennent les maîtres du secteur.Since the 19th century, the sector of French fashion economy has been deeply transformed. From a world of craftmen with a high know-how, it has moved to a world dominated by the industry and the mass market. The creators desappear one after another, and omnipotent designers supersede them. Today the luxury industry is ruled by marketing and advertising.

L’iconographie de l’Hymne Acathiste dans les fresques de l’église St.Onuphre du monastère Lavrov et dans la peinture extérieure moldave au temps du premier règne de Petru Rares

Directory of Open Access Journals (Sweden)

Constantin I. Ciobanu

2010-01-01

Full Text Available L’église St. Onuphre du monastère Lavrov (Ukraine occidentale, près de Staryi Sambir conserve des peintures murales qu’on a datées de la fin du XVe ou du début du XVIe siècle. Le but de la présente étude est de préciser les affinités d’ordre iconographique existentes entre les versions de l’«Hymne Acathiste» de Lavrov et des églises moldaves à peinture extérieure du temp du premier règne de Petru Rareş. Grâce à la rédaction de l’image de l’«Acathiste» de Probota, où le début du texte de la 17e strophe de l’«Hymne» est bien conservé, on peut constater qu’à Lavrov, dans l’image similaire, il ne s’agit pas de la 24e strophe de l’«Hymne» comme le croyait A. I. Rogov, maïs de la 17e strophe. Donc, on peut supposer, qu’à Lavrov il n’y avait pas de lacune dans la présentation des strophes 19–23 de l’«Hymne Acathiste».

Rendez-vous avec les oeuvres du Musée: le speed dating au MAH : quinze minutes pour convaincre

OpenAIRE

Matthey, David

2015-01-01

Tiré du site internet du blog des Musées d'art et d'histoire (http://blog.mahgeneve.ch): "Lors des soirées Afterwork tenues au MAH durant les mois d'octobre et de novembre, les séances de speed dating – un commentaire d'une quinzaine de minutes consacré à une oeuvre ou à un ensemble d'oeuvres – ont remporté un franc succès. Cet engouement nous conforte dans l'idée d'en faire le fil rouge de nos futures manifestations de fin de journée ! Mais pourquoi cette formule?".

An experimental investigation on the airside performance of fin-and-tube heat exchangers having slit fins under wet condition

International Nuclear Information System (INIS)

Kim, Nae Hyun; Kim, Tae Hun

2015-01-01

In this study, the heat transfer and friction characteristics of the 5.3 mm O.D. slit-finned heat exchangers under wet condition have been experimentally investigated. Plain-finned heat exchangers having the same 5.3 mm O.D. tubes are also tested for comparison purpose. The effect of fin pitch on j and f factor is negligible. Slit fin samples yield higher j and f factors than plain fin samples. For one row configuration, the average f factor ratio between slit fin sample and plain fin sample is 2.18. The ratio increases to 2.41 for two row configuration, and to 2.65 for three row configuration. As for the j factor, the ratios are approximately the same (1.61, 1.70 and 1.71 for one, two and three row configuration). Both j and f factor increase as the number of tube row decreases. The same trend is observed for the plain fin samples. At high Reynolds numbers, the j/f ratios of the slit fin are approximately the same as those of the plain fin. At low Reynolds numbers, the j/f ratios of the slit fin are smaller than those of plain fin. Data are compared with existing correlations.

Experimental Investigation on Effect of Fin Shape on the Thermal-Hydraulic Performance of Compact Fin-and-Tube Heat Exchangers

Science.gov (United States)

Moorthy, P.; Oumer, A. N.; Ishak, M.

2018-03-01

The aim of this paper is to investigate the effect of fin shapes on the performance of compact finned flat tube heat exchangers. Three types of fin shapes namely plain, wavy, and rectangular grooved fins attached to three by three arrays of flat tube banks were considered. Moreover, the tubes were deployed in in-line and staggered arrangements. In addition to the fin shapes, the air velocity and the tube inclination angles were varied and the thermal-hydraulic performance was analysed. On the other hand, the temperatures at the tube surfaces were kept constant to produce constant heat flux throughout the study. The results showed that as flowrate increases, the heat transfer increases, however, the friction factor decreases. Staggered arrangement produces higher heat transfer and friction factor than inline fin. Moreover, the rectangular fin is the best in terms of high heat transfer however the drawback of high friction factor leads the fin to have the least efficiency of all. On the other hand, plain fin had the least heat transfer performance however the highest efficiency was achieved. Therefore, plain fin should be used when efficiency is prioritized and rectangular fin when high heat transfer is desired.

Scenarii pour (quasi-) fin du monde traiter les dangers au CERN

CERN Document Server

Houdart, Sophie

2015-01-01

Au large de Genève court le plus grand dispositif expérimental jamais construit, le LHC, conçu pour comprendre comment s’est aggloméré l’univers. Les physiciens des particules, à l’échelle internationale, y expérimentent les théories physiques les plus avancées sur l’origine et le devenir du monde. Lové 100 mètres sous terre, et donc invisible dans le paysage, cette machine extraordinaire est, en surface, le point de mire de multiples attentions et l’objet de mesures incessantes. Ce dont elle traite (le Big Bang, les trous noirs, l’antimatière…), son envergure, son empreinte territoriale sont propres à nourrir des scénarios catastrophe que le CERN doit scrupuleusement désamorcer à mesure qu’ils surgissent en usant de procédés hétérogènes : mesures techniques, normes juridiques, monitoring de l’environnement.

Autun (Saône-et-Loire. Étude archéologique du cloître canonial de Saint-Nazaire

Directory of Open Access Journals (Sweden)

Walter Berry

2004-12-01

Full Text Available L’année 2003, qui marquait à la fois les 20 ans de recherches entreprises à l’initiative de Christian Sapin et la fin des investigations de terrain, fut très fructueuse. En effet, outre une étude complémentaire de la zone occidentale du cloître, riche en découvertes, la galerie orientale qui a particulièrement retenu notre attention, recelait des informations capitales pour comprendre de façon plus précise l’histoire du site. À l’est, justement, d’autres parties d’une vaste habitation de l’An...

Les sépultures chasséennes du sud de la France

Directory of Open Access Journals (Sweden)

Alain BEYNEIX

2009-12-01

Full Text Available ABSTRACT: A new exam of the «royal» sepulture of Saint-Michel-clu-Touch in Toulouse (dép. Haute- Garonne and a bibliographical study about chassean sepultures in southern France permit to present social aspects of the chassean communities in this area. This study shows on the one hand, a glaring diversity about mortuary practises and rituals, on the other hand, the beginning of a social hiérarchisation. Some sepultures present an architecture or else furnitures which illustre the presence of powerful people in the populations of first farmers in the end of the 5 the millenium and in the beginning of the 4 the millenium B.C. in southern France.RÉSUMÉ: Le réexamen de la sépulture dite «royale» de Saint-Michel-du-Touch à Toulouse (Haute- Garonne suivi d'une étude bibliographique des sépultures chasséennes du sud de la France permettent de relever quelques aspects sociaux des communautés du Néolithique moyen de cette région. Outre de flagrantes diversités de pratiques et de rites funéraires, l'étude de ces sépultures dénote tin début de hiérarchisation sociale. Certaines tombes par leur architecture ou par la qualité de leur mobilier apparaissent comme la preuve tangible d'un phénomène d'émergence du pouvoir au sein des populations de premiers agriculteurs dès la fin du Vo et du début du IV millénaire avant J.C. dans le sud de la France.

Advanced microchannel heat exchanger with S-shaped fins

International Nuclear Information System (INIS)

Tsuzuki, Nobuyoshi; Ishizuka, Takao; Kato, Yasuyoshi; Nikitin, Konstantin

2009-01-01

Fin shape effects on thermal-hydraulic characteristics were studied for a Microchannel Heat Exchanger (MCHE) with S-shaped fins using 3D-CFD and changing the fin parameters: fin angle, overlapping length, fin width, fin length, and edge roundness. The fin angle effect on the pressure drop is consistent with the equation obtained experimentally by Weisbach for a circular bent tube: the pressure drop in the S-shaped fin configuration results from bent flow. The overlap of fins with those located immediately downstream at the offset position provides a guide wing effect that reduces the pressure drop remarkably. The overlap was changed by changing the fin radial position and arc length. The pressure drop was minimized when the downstream fins are placed in the middle of the bent flow channels formed by the fins upstream, which differs from Ito's configuration obtained from experiments with a single bent duct. Regarding arc length, the pressure drop is minimized at the standard overlapping length, which was formed to have the longest arc without a change in channel width. Shorter arc lengths from the optimum value by 30 and 50%, respectively, give 2.4 and 4.6% decreases in the heat transfer rate and 17 and 13% increases in the pressure drop. Thinner fins show better thermal-hydraulic performance for fin widths of 0.2-0.8 mm. However, the pressure drop reduced by the longer fin and heat transfer rate was also reduced. Rounded fins with 0.1 mm radius increased the pressure drop by about 30% compared with that of the fin designed with no roundness. (author)

Fin shape thermal optimization using Bejan's constuctal theory

CERN Document Server

Lorenzini, Giulio

2011-01-01

The book contains research results obtained by applying Bejan's Constructal Theory to the study and therefore the optimization of fins, focusing on T-shaped and Y-shaped ones. Heat transfer from finned surfaces is an example of combined heat transfer natural or forced convection on the external parts of the fin, and conducting along the fin. Fin's heat exchange is rather complex, because of variation of both temperature along the fin and convective heat transfer coefficient. Furthermore possible presence of more fins invested by the same fluid flow has to be considered.Classical fin theory tri

Constitution et processus d'intégration socio-économique d'une micro-colonie chinoise dans une communauté andine à la fin du XIXe siècle: Acos - vallée du Chancay

Directory of Open Access Journals (Sweden)

1980-01-01

Full Text Available Plus de 80000 Chinois furent 'importés de force' au Pérou entre 1854 et 1874, année où le Traité de Tien Tsin mit fin à ce trafic. Le Pérou de cette seconde moitié du XIXe souffrait d'un manque de main-d'oeuvre aigu, situation aggravée par la libération des esclaves noirs d'une part et d'autre part par l'essor prit par les haciendas sucrières, la construction des premières lignes de chemin de fer et l'extraction du guano. Entre 1860 et 1870 par exemple arrivèrent au seul port de Callao plus de 38000 'coolies'. En 1876, dans la province de Chancay à Aucallama étaient employés 1225 'asiáticos' soit plus de 66% de la population locale. A la fin du siècle, beaucoup étaient morts, certains avaient réussi à retourner en Chine, et d'autres s'étaient définitivement installés, rejoints par une seconde vague de Chinois commerçants attirés par l'essor du Pérou. La plupart des Chinois s'établirent sur la côte où ils étaient arrivés et dans des centres urbains. Même parmi ceux qui travaillèrent dans la construction des chemins de fer, très peu s'installèrent définitivement dans les régions minières d'altitude. A Acos, petite communauté (300 à 400 habitants de la vallée du Chancay établie dans un fond de vallée chaude ou 'quebrada de yunga', on a retrouvé la présence d'une micro-colonie de Chinois. Dans quelles circonstances aboutirent-ils dans ce village de 'sierra' (1 550 m? Comment s'y intégrèrent-ils et quel fut leur rôle économique sont les questions que nous nous poserons dans cet article, puis dans un suivant traitant spécifiquement de leur rôle dans l'essor du village. Notons un dernier point: le village d'Acos à l'arrivée des Chinois était dominé par un groupe de familles dites 'légitimes' qui détenaient surtout un pouvoir fondé sur la propriété foncière. Les Chinois, en contribuant à développer l'économie de marché, entrèrent en conflit avec ce groupe mais surent aussi se le

Experimental Validation of Elliptical Fin-Opening Behavior

Directory of Open Access Journals (Sweden)

James M. Garner

2003-01-01

Full Text Available An effort to improve the performance of ordnance has led to the consideration of the use of folding elliptical fins for projectile stabilization. A second order differential equation was used to model elliptical fin deployment history and accounts for: deployment with respect to the geometric properties of the fin, the variation in fin aerodynamics during deployment, the initial yaw effect on fin opening, and the variation in deployment speed based on changes in projectile spin. This model supports tests conducted at the Transonic Experimental Facility, Aberdeen Proving Ground examining the opening behavior of these uniquely shaped fins. The fins use the centrifugal force from the projectile spin to deploy. During the deployment, the fin aerodynamic forces vary with angle-of-attack changes to the free stream. Model results indicate that projectile spin dominates the initial opening rates and aerodynamics dominate near the fully open state. The model results are examined to explain the observed behaviors, and suggest improvements for later designs.

Effect of Using Extra Fins on the Pin Fin Classic Geometry for Enhancement Heat Sink Performance using EGM Method

Directory of Open Access Journals (Sweden)

Kadhum Audaa Jehhef

2018-04-01

Full Text Available In the present study, the effect of new cross-section fin geometries on overall thermal/fluid performance had been investigated. The cross-section included the base original geometry of (triangular, square, circular, and elliptical pin fins by adding exterior extra fins along the sides of the origin fins. The present extra fins include rectangular extra fin of 2 mm (height and 4 mm (width and triangular extra fin of 2 mm (base 4 mm (height. The use of entropy generation minimization method (EGM allows the combined effect of thermal resistance and pressure drop to be assessed through the simultaneous interaction with the heat sink. A general dimensionless expression for the entropy generation rate is obtained by considering a control volume around the pin fin including a base plate and applying the conservations equations of mass and energy with the entropy balance. The dimensionless numbers used includes the aspect ratio (ε, Reynolds number (Re, Nusselt number (Nu, and the drag coefficients (CD. Fourteen different cross-section fin geometries are examined for the heat transfer, fluid friction, and the minimum entropy generation rate. The results showed that the Nusselt number increases with increasing the Reynolds number for all employed models. The ellipse models (ET and ER-models give the highest value in the Nusselt number as compared with the classical pin fins. The fin of the square geometry with four rectangular extra fins (SR-models gives an agreement in Nusselt number as compared with the previous study.

Chronologie du Yémen contemporain (1904-1970

Directory of Open Access Journals (Sweden)

Ségolène Samouiller

2001-09-01

Full Text Available De l'avènement de l'imam Yahyâ en 1904 à la fin de la guerre civile au Nord et la naissance de la RPDSY en 1969-1970, le Yémen n'a pas échappé aux secousses du XXe siècle : guerres mondiales, colonisation et décolonisation, nationalisme et revendications sociales. Le tableau chronologique qui enregistre une partie des événements entre ces deux dates pour le Yémen du Nord et du Sud, est avant tout conçu comme un outil de travail appelé à s'enrichir et à servir de support à la lecture des dynamiques politiques, particulièrement pour la décennie charnière 1960-1970.Chronology of Contemporary Yemen (1900-1970From the rise of Imam Yahyâ to the end of the civil war in the North and the birth of the PDRY in 1969-1970, Yemen did not escape the tribulations of the 20th century : World Wars, colonization and then decolonization, nationalism and social demands. This chronology relates part of the events that occurred in North and South Yemen during this seventy-year period. It is to be considered mainly as a working tool and is therefore meant to be  continuously updated and used as medium for the understanding of political change, particularly during the 1960-1970 decade.

从FinTech到RegTech

Institute of Scientific and Technical Information of China (English)

孙国峰[1,2

2017-01-01

本文分析FinTech（金融科技）监管的必要性，并介绍了FinTech监管的国际经验，在此基础上提出了我国可以探索将人工智能应用于金融监管，即以RegTech（监管科技）应对FinTech的建议。

La cuisine et la table dans la France de la fin du Moyen Âge. Colloque et exposition

Directory of Open Access Journals (Sweden)

Fabienne Ravoire

2004-12-01

Full Text Available Les 8, 9 et 10 janvier 2004, un colloque interdisciplinaire s’est tenu à Sens, au Centre de Recherche et d'Étude du Patrimoine (umr 5594 et musées de Sens. Organisé par Fabienne Ravoire (inrap, umr 5594 et Anne Dietrich (inrap, umr 7041, il avait pour objectif de présenter, par le biais d’une approche pluridisciplinaire, un état des lieux de la recherche sur l’alimentation et les manières de la table au tournant du Moyen Âge et de la Renaissance. Avec le renouvellement des données archéolo...

Thermal transport in oblique finned microminichannels

CERN Document Server

Fan, Yan; Singh, Pawan Kumar; Lee, Yong Jiun

2015-01-01

The main aim of this book is to introduce and give an overview of a novel, easy, and highly effective heat transfer augmentation technique for single-phase micro/minichannel heat sink. The specific objectives of the volume are to: Introduce a novel planar oblique fin microchannel and cylindrical oblique fin minichannel heat sink design using passive heat transfer enhancement techniques  Investigate the thermal transport in both planar and cylindrical oblique fin structures through numerical simulation and systematic experimental studies. Evaluate the feasibility of employing the proposed solution in cooling non-uniform heat fluxes and hotspot suppression Conduct the similarity analysis and parametric study to obtain empirical correlations to evaluate the total heat transfer rate of the oblique fin heat sink Investigate the flow mechanism and optimize the dimensions of cylindrical oblique fin heat sink Investigate the influence of edge effect on flow and temperature uniformity in these oblique fin chan...

UOP FIN 571 Final Exam Guide New

OpenAIRE

ADMIN

2018-01-01

UOP FIN 571 Final Exam Guide New Check this A+ tutorial guideline at http://www.fin571assignment.com/fin-571-uop/fin-571-final-exam-guide -latest For more classes visit http://www.fin571assignment.com Question 1 The underlying assumption of the dividend growth model is that a stock is worth: A. An amount computed as the next annual dividend divided by the required rate of return. B. An amount computed as the next annual dividend divided by the ma...

La fin des certitudes temps, chaos et les lois de la nature

CERN Document Server

Prigogine, Ilya

1996-01-01

« En cette fin de siècle, la question de l'avenir de la science est souvent posée. Je crois que nous sommes seulement au début de l'aventure. Nous assistons à l'émergence d'une science qui n'est plus limitée à des situations simplifiées, idéalisées, mais nous met en face de la complexité du monde réel, une science qui permet à la créativité humaine de se vivre comme l'expression singulière d'un trait fondamental de tous les niveaux de la nature. J'ai tenté de présenter cette transformation conceptuelle qui implique l'ouverture d'un nouveau chapitre dans l'histoire féconde des relations entre physique et mathématique sous une forme lisible et accessible à tout lecteur intéressé par l'évolution de nos idées sur la nature. Nous ne sommes qu'au début de ce nouveau chapitre de l'histoire de notre dialogue avec la nature. » Ilya PrigogineIlya Progogine, prix Nobel de chimie, est professeur à l'université libre de Bruxelles et à l'université du Texas à Austin.

Numerical studies on heat transfer and pressure drop characteristics of flat finned tube bundles with various fin materials

Science.gov (United States)

Peng, Y.; Zhang, S. J.; Shen, F.; Wang, X. B.; Yang, X. R.; Yang, L. J.

2017-11-01

The air-cooled heat exchanger plays an important role in the field of industry like for example in thermal power plants. On the other hand, it can be used to remove core decay heat out of containment passively in case of a severe accident circumstance. Thus, research on the performance of fins in air-cooled heat exchangers can benefit the optimal design and operation of cooling systems in nuclear power plants. In this study, a CFD (Computational Fluid Dynamic) method is implemented to investigate the effects of inlet velocity, fin spacing and tube pitch on the flow and the heat transfer characteristics of flat fins constructed of various materials (316L stainless steel, copper-nickel alloy and aluminium). A three dimensional geometric model of flat finned tube bundles with fixed longitudinal tube pitch and transverse tube pitch is established. Results for the variation of the average convective heat transfer coefficient with respect to cooling air inlet velocity, fin spacing, tube pitch and fin material are obtained, as well as for the pressure drop of the cooling air passing through finned tube. It is shown that the increase of cooling air inlet velocity results in enhanced average convective heat transfer coefficient and decreasing pressure drop. Both fin spacing and tube pitch engender positive effects on pressure drop and have negative effects on heat transfer characteristics. Concerning the fin material, the heat transfer performance of copper-nickel alloy is superior to 316L stainless steel and inferior to aluminium.

Saddle-fin cell transistors with oxide etch rate control by using tilted ion implantation (TIS-fin) for sub-50-nm DRAMs

International Nuclear Information System (INIS)

Yoo, Min Soo; Choi, Kang Sik; Sun, Woo Kyung

2010-01-01

As DRAM cell pitch size decreases, the need for a high performance transistor is increasing. Though saddle-fin (S-fin) transistors have superior characteristics, S-fin transistors are well known to be more sensitive to process variation. To make uniform S-fin transistors, for the first time, we developed a new fin formation method using tilted ion implantation along the wordline direction after a recess gate etch. Due to the increased etch rate of the oxide film by ion implantation damage, fins are made at the bottom channel of the recess gate after wet etching. The resulting tilt implanted saddle-fin (TIS-fin) transistor has remarkably improved characteristics, such as ∼8% subthreshold swing (SS) and a 40% drain induced barrier lowering (DIBL) decrease. Especially, the TIS-fin with a neutral dopant has a reduced threshold voltage (Vth) variation within a wafer (<100 mV), which is comparable with that of a mass-produced sphere-shaped recessed channel array transistor (SRCAT).

Investigation of internally finned LED heat sinks

Science.gov (United States)

Li, Bin; Xiong, Lun; Lai, Chuan; Tang, Yumei

2018-03-01

A novel heat sink is proposed, which is composed of a perforated cylinder and internally arranged fins. Numerical studies are performed on the natural convection heat transfer from internally finned heat sinks; experimental studies are carried out to validate the numerical results. To compare the thermal performances of internally finned heat sinks and externally finned heat sinks, the effects of the overall diameter, overall height, and installation direction on maximum temperature, air flow and heat transfer coefficient are investigated. The results demonstrate that internally finned heat sinks show better thermal performance than externally finned heat sinks; the maximum temperature of internally finned heat sinks decreases by up to 20% compared with the externally finned heat sinks. The existence of a perforated cylinder and the installation direction of the heat sink affect the thermal performance significantly; it is shown that the heat transfer coefficient of the heat sink with the perforated cylinder is improved greater than that with the imperforated cylinder by up to 34%, while reducing the mass of the heat sink by up to 13%. Project supported by the Scientific Research Fund of Sichuan Provincial Education Department (No. 18ZB0516) and the Sichuan University of Arts and Science (No. 2016KZ009Y).

Role of Pectoral Fin Flexibility in Robotic Fish Performance

Science.gov (United States)

Bazaz Behbahani, Sanaz; Tan, Xiaobo

2017-08-01

Pectoral fins play a vital role in the maneuvering and locomotion of fish, and they have become an important actuation mechanism for robotic fish. In this paper, we explore the effect of flexibility of robotic fish pectoral fins on the robot locomotion performance and mechanical efficiency. A dynamic model for the robotic fish is presented, where the flexible fin is modeled as multiple rigid elements connected via torsional springs and dampers. Blade element theory is used to capture the hydrodynamic force on the fin. The model is validated with experimental results obtained on a robotic fish prototype, equipped with 3D-printed fins of different flexibility. The model is then used to analyze the impacts of fin flexibility and power/recovery stroke speed ratio on the robot swimming speed and mechanical efficiency. It is found that, in general, flexible fins demonstrate advantages over rigid fins in speed and efficiency at relatively low fin-beat frequencies, while rigid fins outperform flexible fins at higher frequencies. For a given fin flexibility, the optimal frequency for speed performance differs from the optimal frequency for mechanical efficiency. In addition, for any given fin, there is an optimal power/recovery stroke speed ratio, typically in the range of 2-3, that maximizes the speed performance. Overall, the presented model offers a promising tool for fin flexibility and gait design, to achieve speed and efficiency objectives for robotic fish actuated with pectoral fins.

The shark's fin

International Nuclear Information System (INIS)

Listinsky, J.L.; Griffiths, H.J.

1989-01-01

Initial plain film studies of seven patients with facet fracture-dislocations of the cervical spine were examined retrospectively. Rotation of the cross-table lateral film from a standard vetical viewing orientation to a simulated brow-down position allowed easier appreciation of the dislocated pillar in six of the seven patients. The displaced pillar had an appearance similar to that of the dorsal fin of a shark. We conclude that the finding of a shark's fin appearance of an articular pillar in a traumatized patient warrants further radiographic studies. (author). 8 refs.; 3 figs

Room to high temperature measurements of flexible SOI FinFETs with sub-20-nm fins

KAUST Repository

Diab, Amer El Hajj

2014-12-01

We report the temperature dependence of the core electrical parameters and transport characteristics of a flexible version of fin field-effect transistor (FinFET) on silicon-on-insulator (SOI) with sub-20-nm wide fins and high-k/metal gate-stacks. For the first time, we characterize them from room to high temperature (150 °C) to show the impact of temperature variation on drain current, gate leakage current, and transconductance. Variation of extracted parameters, such as low-field mobility, subthreshold swing, threshold voltage, and ON-OFF current characteristics, is reported too. Direct comparison is made to a rigid version of the SOI FinFETs. The mobility degradation with temperature is mainly caused by phonon scattering mechanism. The overall excellent devices performance at high temperature after release is outlined proving the suitability of truly high-performance flexible inorganic electronics with such advanced architecture.

A Biologically Derived Pectoral Fin for Yaw Turn Manoeuvres

Directory of Open Access Journals (Sweden)

Jonah R. Gottlieb

2010-01-01

Full Text Available A bio-robotic fin has been developed that models the pectoral fin of the bluegill sunfish as the fish turned to avoid an obstacle. This work involved biological studies of the sunfish fin, the development of kinematic models of the motions of the fin's rays, CFD based predictions of the 3D forces and flows created by the fin, and the implementation of simplified models of the fin's kinematics and mechanical properties in a physical model. The resulting robotic fin produced the forces and flows that drove the manoeuvre and had a sufficiently high number of degrees of freedom to create a variety of non-biologically derived motions. The results indicate that for robotic fins to produce a level of performance on par with biological fins, both the kinematics and the mechanical properties of the biological fin must be modelled well.

Parametric CFD Analysis to Study the Influence of Fin Geometry on the Performance of a Fin and Tube Heat Exchanger

DEFF Research Database (Denmark)

Singh, Shobhana; Sørensen, Kim; Condra, Thomas Joseph

2016-01-01

Heat transfer and pressure loss characteristics of a fin and tube heat exchanger are numerically investigated based on parametric fin geometry. The cross-flow type heat exchanger with circular tubes and rectangular fin profile is selected as a reference design. The fin geometry is varied using...... a design aspect ratio as a variable parameter in a range of 0.1-1.0 to predict the impact on overall performance of the heat exchanger. In this paper, geometric profiles with a constant thickness of fin base are studied. Three-dimensional, steady state CFD model is developed using commercially available...... are determined. The best performed geometric fin profile based on the higher heat transfer and lower pressure loss is predicted. The study provides insights into the impact of fin geometry on the heat transfer performance which help escalate the understanding of heat exchanger designing and manufacturing...

Effect of fin pitch and number of tube rows on the air side performance of herringbone wavy fin and tube heat exchangers

International Nuclear Information System (INIS)

Wongwises, Somchai; Chokeman, Yutasak

2005-01-01

An experimental study is conducted to investigate the effects of a fin pitch and number of tube rows on the air side performance of fin and tube heat exchangers having herringbone wavy fin configuration at various fin thicknesses. A total of 10 samples of fin and tube heat exchanger with a tube outside diameter of 9.53mm, transverse tube pitch of 25.4mm and longitudinal tube pitch of 19.05mm, having various fin pitches, number of tube rows and fin thicknesses, are tested in a well insulated open wind tunnel. The heat exchangers are made from aluminium plate finned, copper tube. Ambient air is used as a working fluid in the air side while hot water is used for the tube side. The results are presented as the variation of the Colburn factor and the friction factor with the Reynolds number based on the fin collar outside diameter (Re D c ). The experimental results reveal that the fin pitch has an insignificant effect on the heat transfer characteristic. The friction factor increases with increasing fin pitch when Re D c >2500, approximately. The Colburn factor and the friction factor decrease with increasing number of tube rows when Re D c <4000, approximately. These results remain the same when the fin thickness is changed

Performance of tubes-and plate fins heat exchangers

International Nuclear Information System (INIS)

Rosman, E.C.

1979-11-01

By means of a two-dimensional analysis performance, and using local heat transfer coefficients, the plate fin temperature distribution, the air bulk temperature along the stream path and the fin efficiency can be obtained, for several Reynolds numbers and fin materials. Herein are also presented the average heat transfer coefficients for isothermal plate fins, referring to heat exchangers with central-tube and rear-tube row and to two-row tubes heat exchangers configurations. It is possible to obtain the real tax or the real area of heat transfer, using the average hea transfer coefficients for isothermal plate fins and the fin efficiency. (Author) [pt

Fish locomotion: kinematics and hydrodynamics of flexible foil-like fins

Science.gov (United States)

Lauder, George V.; Madden, Peter G. A.

2007-11-01

The fins of fishes are remarkable propulsive devices that appear at the origin of fishes about 500 million years ago and have been a key feature of fish evolutionary diversification. Most fish species possess both median (midline) dorsal, anal, and caudal fins as well as paired pectoral and pelvic fins. Fish fins are supported by jointed skeletal elements, fin rays, that in turn support a thin collagenous membrane. Muscles at the base of the fin attach to and actuate each fin ray, and fish fins thus generate their own hydrodynamic wake during locomotion, in addition to fluid motion induced by undulation of the body. In bony fishes, the jointed fin rays can be actively deformed and the fin surface can thus actively resist hydrodynamic loading. Fish fins are highly flexible, exhibit considerable deformation during locomotion, and can interact hydrodynamically during both propulsion and maneuvering. For example, the dorsal and anal fins shed a vortex wake that greatly modifies the flow environment experienced by the tail fin. New experimental kinematic and hydrodynamic data are presented for pectoral fin function in bluegill sunfish. The highly flexible sunfish pectoral fin moves in a complex manner with two leading edges, a spanwise wave of bending, and substantial changes in area through the fin beat cycle. Data from scanning particle image velocimetry (PIV) and time-resolved stereo PIV show that the pectoral fin generates thrust throughout the fin beat cycle, and that there is no time of net drag. Continuous thrust production is due to fin flexibility which enables some part of the fin to generate thrust at all times and to smooth out oscillations that might arise at the transition from outstroke to instroke during the movement cycle. Computational fluid dynamic analyses of sunfish pectoral fin function corroborate this conclusion. Future research on fish fin function will benefit considerably from close integration with studies of robotic model fins.

FinFET modeling for IC simulation and design

CERN Document Server

Hu, Chenming; Lu, Darsen D

2015-01-01

This book is the first to explain FinFET modeling for IC simulation and the industry standard - BSIM-CMG - describing the rush in demand for advancing the technology from planar to 3D architecture, as now enabled by the approved industry standard. The book gives a strong foundation on the physics and operation of FinFET, details aspects of the BSIM-CMG model such as surface potential, charge and current calculations, and includes a dedicated chapter on parameter extraction procedures, providing a step-by-step approach for the efficient extraction of model parameters. With this book you will learn: * Why you should use FinFET* The physics and operation of FinFET* Details of the FinFET standard model (BSIM-CMG)* Parameter extraction in BSIM-CMG* FinFET circuit design and simulation * Authored by the lead inventor and developer of FinFET, and developers of the BSIM-CM standard model, providing an experts' insight into the specifications of the standard* The first book on the industry-standard FinFET model - BSIM...

Enquête sur l'utilisation du téléphone mobile pour le développement ...

International Development Research Centre (IDRC) Digital Library (Canada)

Au Ghana, comme dans d'autres pays en développement, les téléphones mobiles sont omniprésents, et ils sont utilisés tant à des fins personnelles que professionnelles. Le but de ce projet sera d'établir la contribution du téléphone mobile à la croissance des petites entreprises, au moyen d'une enquête réalisée dans les ...

Soil formation on Holocene moraines in the cirque de Troumouse, Pyrenees

Directory of Open Access Journals (Sweden)

Parkinson, Robert

1991-12-01

Full Text Available Factors affecting rates and degree of soil formation on Holocene moraines are discussed with reference to moraine sequences in the Cirque de Troumouse, French Pyrenees. In particular, the role of time, slope position and post-depositional history are evaluated for three moraines ranging in age from c. 5000 to c. 1000 yr BP. Soil profile development, as determined by visual criteria, indicates differences in soil development between moraines of different age as well as between soils developed on the same moraine but occupying different slope positions. Particle size analysis and soil chemical analyses confirm that microtopography exerts a strong control on the extent and rate of soil formation, and must therefore be considered when sampling and describing soil chronosequences on glacial moraines.

[es] Se discuten los factores que afectan a las tasas y al grado de formación del suelo en morrenas Holocenas, con referencia a la secuencia de morrenas en el Circo de Troumouse, Pirineo francés. En particular, se evalúa el papel del tiempo, la posición de la pendiente y la historia postdeposicional para tres morrenas ordenadas en edad desde c. 5000 a c. 1000 años BP. El desarrollo del perfil del suelo, determinado por criterios visuales, indica diferencias de desarrollo del suelo entre morrenas de diferente edad así como entre suelos desarrollados en la misma morrena, pero ocupando diferentes posiciones de la pendiente. Análisis granulométricos y químicos del suelo confirman que la microtopografía ejerce un fuerte control en la extensión y en la tasa de formación del suelo y, por tanto, deberla ser tenida en cuenta en los muéstreos y descripciones de las cronosecuencias del suelo en morrenas glaciares.
[fr] On discute les facteurs qui affectent les taux et le degré de formation du sol en moraines Holocènes, avec référence à la séquence de moraines du Cirque de Troumouse, Pyrénées français. En particulier, on �

A biorobotic pectoral fin for autonomous undersea vehicles.

Science.gov (United States)

Tangorra, James L; Davidson, S Naomi; Madden, Peter G; Lauder, George V; Hunter, Ian W

2006-01-01

A biorobotic fin for autonomous undersea vehicles (AUVs) was developed based on studies of the anatomy, kinematics, and hydrodynamics of the bluegill sunfish pectoral fin. The biorobotic fin was able to produce many of the complex fin motions used by the sunfish during steady swimming and was used to investigate mechanisms of thrust production and control. This biorobotic fin is an excellent experimental tool and is an important first step towards developing propulsive devices that give AUVs maneuvering characteristics that match and exceed those of highly maneuverable fish.

FinTech in Denmark

OpenAIRE

Hategan, Ramona Anamaria; Mockus, Gytis; Trinkunaite, Sarune

2017-01-01

ABSTRACTThe purpose of this paper has been to seek understanding and knowledge of FinTech phenomenon, with a particular focus on the effect of its emergence on the Danish financial sector. We have attempted to answer our initial research question with the help of a theoretical and methodological framework conceived of concepts belonging to Actor-Network Theory, Diffusion of Innovation Theory and alluding to Foucault’s concepts of power, knowledge and discourses. We have followed FinTech as an...

Investigating the effect of non-similar fins in thermoeconomic optimization of plate fin heat exchanger

International Nuclear Information System (INIS)

Hajabdollahi, Hassan

2015-01-01

Thermoeconomic optimization of plate fin heat exchanger with similar (SF) and different (DF) or non-similar fin in each side is presented in this work. For this purpose, both heat exchanger effectiveness and total annual cost (TAC) are optimized simultaneously using multi-objective particle swarm optimization algorithm. The above procedure is performed for various mass flow rates in each side. The optimum results reveal that no thermoeconomic improvement is observed in the case of same mass flow rate in each side while both effectiveness and TAC are improved in the case of different mass flow rate. For example, effectiveness and TAC are improved 0.95% and 10.17% respectively, for the DF compared with SF. In fact, the fin configuration should be selected more compact in a side with lower mass flow rate compared with the other side in the thermoeconomic viewpoint. Furthermore, for the thermodynamic optimization viewpoint both SF and DF have the same optimum result while for the economic (or thermoeconomic) optimization viewpoint, the significant decrease in TAC is accessible in the case of DF compared with SF. - Highlights: • Thermoeconomic modeling of compact heat exchanger. • Selection of fin and heat exchanger geometries as nine decision variables. • Applying MOPSO algorithm for multi objective optimization. • Considering the similar and different fin specification in each side. • Investigation of optimum design parameters for various mass flow rates

Flexible nanoscale high-performance FinFETs

KAUST Repository

Sevilla, Galo T.

2014-10-28

With the emergence of the Internet of Things (IoT), flexible high-performance nanoscale electronics are more desired. At the moment, FinFET is the most advanced transistor architecture used in the state-of-the-art microprocessors. Therefore, we show a soft-etch based substrate thinning process to transform silicon-on-insulator (SOI) based nanoscale FinFET into flexible FinFET and then conduct comprehensive electrical characterization under various bending conditions to understand its electrical performance. Our study shows that back-etch based substrate thinning process is gentler than traditional abrasive back-grinding process; it can attain ultraflexibility and the electrical characteristics of the flexible nanoscale FinFET show no performance degradation compared to its rigid bulk counterpart indicating its readiness to be used for flexible high-performance electronics.

Final Pleistocene and Early Holocene at Sitio do Meio, Piauí, Brazil: Stratigraphy and comparison with Pedra Furada

Directory of Open Access Journals (Sweden)

Giulia Aimola

2014-09-01

Full Text Available English: Sitio do Meio, in southern Piaui, Brazil, is the second rock shelter presenting fully Pleistocene dates and artefacts after Pedra Furada.  Despite the anthropogenic origin of Pedra Furada artefacts has been questioned, SDM has better chances to be accepted by the scientific community because of the absence of the most relevant stone breaking agents in this kind of site, i.e. waterfalls. This paper presents a critical revision of the history of excavations (1980-2000, stratigraphy, chronology, and the archaeological content of the site (sector 2. At least 98 stone tools have been identified and described, all of them being older than 12,500 BP, i.e. belonging to the Upper Pleistocenic phase of Pedra Furada 3, as defined in the close reference site. The lithic industry of Serra Talhada phase (lower Holocene is also presented and compared with paleoindian sites of North-Eastern and Central Brazil.French:Le Sitio do meio, dans le  Piaui méridional (Brésil est le deuxième abri sous roche de la région ayant livré des dates pléistocènes en dehors du site de la Pedra Furada. L'article présente une révision critique des fouilles (1980-2000, la chronostratigraphie et le contenu archéologique du secteur 2. Une centaine d'outils lithiques sont décrits, ils sont plus anciens de 12,5 ka BP  et correspondent à la phase Pléistocène Pedra Furada 3 définie dans le site éponyme de référence. On présente aussi l' industrie lithique de la phase Serra Talhada (Holocène  ancien en la comparant aux industries paléoindiennes du Nord-Est et du centre du Brésil.

Holocene glacial fluctuations in southern South America

Science.gov (United States)

Reynhout, S.; Sagredo, E. A.; Kaplan, M. R.; Aravena, J. C.; Martini, M. A.; Strelin, J. A.; Schaefer, J. M.

2016-12-01

Understanding the timing and magnitude of former glacier fluctuations is critical to decipher long-term climatic trends and to unravel both natural cycles and human impact on the current glacial behavior. Despite more than seven decades of research efforts, a unifying model of Holocene glacial fluctuations in Southern South America remains elusive. Here, we present the state-of-the-art regarding the timing of Holocene glacial fluctuation in southern Patagonia-Tierra del Fuego, with a focus on a new generation of high-resolution radiocarbon and 10Be surface exposure dating chronologies. Recently acquired evidence suggest that after receding from advanced Late Glacial positions, Patagonian glaciers were for the most part close to, or even behind, present ice margins during the Early Holocene. On the other hand, emerging chronologies indicate that in some areas there were extensive expansions (century scale?) that punctuated the warm interval. Subsequently, we have evidence of multiple millennial timescale glacial advances starting in the middle Holocene. Several glacial maxima are defined by moraines and other landforms from 7000 years ago to the 19th century, with a gap sometime between 4,500 and 2,500 years ago. The last set of advances began around 800-600 years ago. Although glacial activity is documented in Patagonia at the same time as the European Little Ice Age, the extent of these glacial events are less prominent than those of the mid-Holocene. The causes that may explain these glacial fluctuations remain elusive. Finally, we discuss ongoing efforts to better define the timing and extent of Holocene glaciations in southern South America, and to establish the basis to test competing hypothesis of regional Holocene climate variability.

Implications of fin profiles on overall performance and weight reduction of a fin and tube heat exchanger

DEFF Research Database (Denmark)

Singh, Shobhana; Sørensen, Kim; Simonsen, Anders Schou

2017-01-01

Fin and tube heat exchangers are being used in several industrial applications by means of novel design and optimized performance. Improvements in geometric design may deliver energy efficient and cost-effective heat exchanger performance with reduced weight. In this paper, a systematic study...... on a cross-flow type fin and tube heat exchanger design for a waste heat recovery application is conducted. The geometric profile of the fin is characterized by a dimensionless design variable named aspect ratio which is parametrically varied to obtain different profiles. Two cases, case-I, and case......,000 using computational fluid dynamics. The numerical results obtained for the reference fin profile are verified with the experimental correlations. Dimensionless parameters such as Nusselt number, Euler number, and efficiency index are calculated to predict the overall performance of the heat exchanger...

FinTech in Taiwan: a case study of a Bank's strategic planning for an investment in a FinTech company

OpenAIRE

Hung, Jui-long; Luo, Binjie

2016-01-01

Introduction: Since 2015 is the year of FinTech in Taiwan, it is worth investigating the challenges that emerged when banks were encouraged to invest in FinTech companies for collaboration. This study aims to identify the strategic considerations in the process of searching for FinTech investment targets. Case description: This study used a case study investigation of a top-5 bank in Taiwan. The major data sources include the meeting notes of the FinTech investment task force and interviews w...

Undulating fins produce off-axis thrust and flow structures.

Science.gov (United States)

Neveln, Izaak D; Bale, Rahul; Bhalla, Amneet Pal Singh; Curet, Oscar M; Patankar, Neelesh A; MacIver, Malcolm A

2014-01-15

While wake structures of many forms of swimming and flying are well characterized, the wake generated by a freely swimming undulating fin has not yet been analyzed. These elongated fins allow fish to achieve enhanced agility exemplified by the forward, backward and vertical swimming capabilities of knifefish, and also have potential applications in the design of more maneuverable underwater vehicles. We present the flow structure of an undulating robotic fin model using particle image velocimetry to measure fluid velocity fields in the wake. We supplement the experimental robotic work with high-fidelity computational fluid dynamics, simulating the hydrodynamics of both a virtual fish, whose fin kinematics and fin plus body morphology are measured from a freely swimming knifefish, and a virtual rendering of our robot. Our results indicate that a series of linked vortex tubes is shed off the long edge of the fin as the undulatory wave travels lengthwise along the fin. A jet at an oblique angle to the fin is associated with the successive vortex tubes, propelling the fish forward. The vortex structure bears similarity to the linked vortex ring structure trailing the oscillating caudal fin of a carangiform swimmer, though the vortex rings are distorted because of the undulatory kinematics of the elongated fin.

Strain relaxation of germanium-tin (GeSn) fins

Science.gov (United States)

Kang, Yuye; Huang, Yi-Chiau; Lee, Kwang Hong; Bao, Shuyu; Wang, Wei; Lei, Dian; Masudy-Panah, Saeid; Dong, Yuan; Wu, Ying; Xu, Shengqiang; Tan, Chuan Seng; Gong, Xiao; Yeo, Yee-Chia

2018-02-01

Strain relaxation of biaxially strained Ge1-xSnx layer when it is patterned into Ge1-xSnx fin structures is studied. Ge1-xSnx-on-insulator (GeSnOI) substrate was realized using a direct wafer bonding (DWB) technique and Ge1-xSnx fin structures were formed by electron beam lithography (EBL) patterning and dry etching. The strain in the Ge1-xSnx fins having fin widths (WFin) ranging from 1 μm down to 80 nm was characterized using micro-Raman spectroscopy. Raman measurements show that the strain relaxation increases with decreasing WFin. Finite element (FE) simulation shows that the strain component in the transverse direction relaxes with decreasing WFin, while the strain component along the fin direction remains unchanged. For various Ge1-xSnx fin widths, transverse strain relaxation was further extracted using micro-Raman spectroscopy, which is consistent with the simulation results.

Isotope heterogeneity of Pre-Holocene groundwater in Iceland

DEFF Research Database (Denmark)

Sveinbjörnsdóttir, Á.E.; Arnorsson, S.; Heinemeier, Jan

2007-01-01

In recent years, it has been shown that groundwater with a Pre-Holocene component is more common in the Icelandic bedrock than previously thought. Some of the Pre-Holocene water samples are more depleted in delta H-2 and delta O-18 than any mean annual precipitation in Iceland today due to the cold...... climate at that time. However, most often Pre-Holocene water components cannot be detected based on the water isotopes alone due to mixing with younger and isotopically heavier water. The Cl concentration in relation to the water isotopes in specific areas has proved to be a good indicator of a Pre......-Holocene component in the groundwater. The deuterium excess value may also help to identify water from a different climate regime, if no oxygen shift has occurred. The relative abundance of a Pre-Holocene water component of the Icelandic groundwater has led to the understanding that combined interpretation of water...

Causes of early Holocene desertification in arid central Asia

Energy Technology Data Exchange (ETDEWEB)

Jin, Liya [Lanzhou University, Key Laboratory of Western China' s Environmental System, Lanzhou, Gansu (China); University of Kiel, Institute of Geosciences, Kiel (Germany); Chen, Fahu [Lanzhou University, Key Laboratory of Western China' s Environmental System, Lanzhou, Gansu (China); Morrill, Carrie [University of Colorado, Cooperative Institute for Research in Environmental Sciences, Boulder, CO (United States); NOAA' s National Climatic Data Center, Paleoclimatology Branch, Boulder, CO (United States); Otto-Bliesner, Bette L.; Rosenbloom, Nan [National Center for Atmospheric Research, Climate and Global Dynamics Division, Boulder, CO (United States)

2012-04-15

Paleoclimate records of effective moisture (precipitation minus evaporation, or P-E) show a dry (low effective moisture) period in mid-latitude arid/semi-arid central Asia during the early Holocene (11,000-8,000 years ago) relative to the middle and late Holocene, in contrast to evidence for greater-than-present precipitation at the same time in the south and east Asian monsoonal areas. To investigate the spatial differences in climate response over mid-latitude central Asia and monsoonal Asia we conducted a series of simulations with the Community Climate System Model version 3 coupled climate model for the early, middle and late Holocene. The simulations test the climatic impact of all important forcings for the early Holocene, including changes in orbital parameters, the presence of the remnant Laurentide ice sheet and deglacial freshening of the North Atlantic. Model results clearly show the early Holocene patterns indicated by proxy records, including both the decreased effective moisture in arid central Asia, which occurs in the model primarily during the winter months, and the increase in summer monsoon precipitation in south and east Asia. The model results suggest that dry conditions in the early Holocene in central Asia are closely related to decreased water vapor advection due to reduced westerly wind speed and less evaporation upstream from the Mediterranean, Black, and Caspian Seas in boreal winter. As an extra forcing to the early Holocene climate system, the Laurentide ice sheet and meltwater fluxes have a substantial cooling effect over high latitudes, especially just over and downstream of the ice sheets, but contribute only to a small degree to the early Holocene aridity in central Asia. Instead, most of the effective moisture signal can be explained by orbital forcing decreasing the early Holocene latitudinal temperature gradient and wintertime surface temperature. We find little evidence for regional subsidence related to a stronger summer Asian

Steady-state and transient heat transfer through fins of complex geometry

Directory of Open Access Journals (Sweden)

Taler Dawid

2014-06-01

Full Text Available Various methods for steady-state and transient analysis of temperature distribution and efficiency of continuous-plate fins are presented. For a constant heat transfer coefficient over the fin surface, the plate fin can be divided into imaginary rectangular or hexangular fins. At first approximate methods for determining the steady-state fin efficiency like the method of equivalent circular fin and the sector method are discussed. When the fin geometry is complex, thus transient temperature distribution and fin efficiency can be determined using numerical methods. A numerical method for transient analysis of fins with complex geometry is developed. Transient temperature distributions in continuous fins attached to oval tubes is computed using the finite volume - finite element methods. The developed method can be used in the transient analysis of compact heat exchangers to calculate correctly the heat flow rate transferred from the finned tubes to the fluid.

Holocene palaeoenvironmental history of the Amazonian mangrove belt

Science.gov (United States)

Cohen, Marcelo Cancela Lisboa; Pessenda, Luiz Carlos Ruiz; Behling, Hermann; de Fátima Rossetti, Dilce; França, Marlon Carlos; Guimarães, José Tasso Felix; Friaes, Yuri; Smith, Clarisse Beltrão

2012-11-01

Wetland dynamic in the northern Brazilian Amazon region during the Holocene was reviewed using palynological, carbon and nitrogen isotopes records, and C/N ratio previously published. The integration of 72 radiocarbon dates recorded in 34 sediment cores sampled along the marine and fluvial littoral, and mainly influenced by the Amazon River, reveals that marine influence and mangrove vegetation were wider than today on the mouth of Amazon River between >8990-8690 and 2300-2230 cal yr BP, forming a continuous mangrove belt along the northern Brazilian Amazon littoral. The establishment of this mangrove strip is a direct consequence of the marine incursion caused by post-glacial sea-level rise possibly associated with tectonic subsidence during the Early and Middle Holocene. In the Late Holocene, in areas influenced by the Amazon River discharge, the mangroves were replaced by freshwater vegetation, and the coast morphology evolved from an estuarine dominated into a rectilinear coast due to coastal progradation. Nevertheless, the marine-influenced littoral, which is currently dominated by mangroves and salt-marsh vegetation, has persistently had brackish water vegetation over tidal mud flats throughout the entire Holocene. Likely, the fragmentation of this continuous mangrove line during the Late Holocene was caused by the increase of river freshwater discharge associated to the change from dry into wet climates in the Late Holocene. This caused a significant decrease of tidal water salinity in areas near the mouth of Amazon River. These changes in the Amazon discharge are probably associated with dry and wet periods in the northern Amazon region during the Holocene.

Antioxidant and Antiproliferative Activities of Heated Sterilized Pepsin Hydrolysate Derived from Half-Fin Anchovy (Setipinna taty

Directory of Open Access Journals (Sweden)

Dongfeng Wang

2011-06-01

Full Text Available In this paper we studied the antioxidant and antiproliferative activities of the heated pepsin hydrolysate from a marine fish half-fin anchovy (HAHp-H. Furthermore, we compared the chemical profiles including the amino acid composition, the browning intensity, the IR and UV-visible spectra, and the molecular weight distribution between the half-fin anchovy pepsin hydrolysate (HAHp and HAHp-H. Results showed that heat sterilization on HAHp improved the 1,1-diphenyl-2-picryl-hydrazil (DPPH radical-scavenging activity and reducing power. In addition, the antiproliferative activities were all increased for HAHp-H on DU-145 human prostate cancer cell line, 1299 human lung cancer cell line and 109 human esophagus cancer cell line. The contents of free amino acid and reducing sugar of HAHp-H were decreased (P < 0.05. However, hydrophobic amino acid residues and the browning intensity of HAHp-H were increased. FT-IR spectroscopy indicated that amide I and amide III bands of HAHp-H were slightly modified, whereas band intensity of amide II was reduced dramatically. Thermal sterilization resulted in the increased fractions of HAHp-H with molecular weight of 3000–5000 Da and below 500 Da. The enhanced antioxidant and antiproliferative activities of HAHp-H might be attributed to the Maillard reaction.

Dreamlands : des parcs d’attractions aux cités du futur

OpenAIRE

Didelon, Valéry

2012-01-01

Comme l’exposition éponyme qui s’est tenue au Centre Pompidou au printemps et à l’été 2010, le catalogue Dreamlands entend nous éclairer sur ce qu’ont en commun les premières expositions universelles, Disneyland, Las Vegas et Dubaï. L’hypothèse est ainsi posée : depuis la fin du XIXe siècle, le parc d’attractions serait devenu aux yeux des artistes, des architectes et des urbanistes un modèle pour imaginer et construire la ville de demain. Comme le champ de foire avant lui, il est de facto un...

Open Channel Natural Convection Heat Transfer on a Vertical Finned Plate

International Nuclear Information System (INIS)

Park, Joo Hyun; Heo, Jeong Hwan; Chung, Bum Jin

2013-01-01

The natural convection heat transfer of vertical plate fin was investigated experimentally. Heat transfer systems were replaced by mass-transfer systems, based on the analogy concept. The experimental results lie within the predictions of the existing heat transfer correlations of plate-fin for the natural convections. An overlapped thermal boundary layers caused increasing heat transfer, and an overlapped momentum boundary layers caused decreasing heat transfer. As the fin height increases, heat transfer was enhanced due to increased inflow from the open side of the fin spacing. When fin spacing and fin height are large, heat transfer was unaffected by the fin spacing and fin height. Passive cooling by natural convection becomes more and more important for the nuclear systems as the station black out really happened at the Fukushima NPPs. In the RCCS (Reactor Cavity Cooling System) of a VHTR (Very High Temperature Reactor), natural convection cooling through duct system is adopted. In response to the stack failure event, extra cooling capacity adopting the fin array has to be investigated. The finned plate increases the surface area and the heat transfer increases. However, the plate of fin arrays may increase the pressure drop and the heat transfer decreases. Therefore, in order to enhance the passive cooling with fin arrays, the parameters for the fin arrays should be optimized. According to Welling and Wooldridge, a natural convection on vertical plate fin is function of Gr, Pr, L, t, S, and H. The present work investigated the natural convection heat transfer of a vertical finned plate with varying the fin height and the fin spacing. In order achieve high Rayleigh numbers, an electroplating system was employed and the mass transfer rates were measured using a copper sulfate electroplating system based on the analogy concept

Plate-fin array cooling using a finger-like piezoelectric fan

International Nuclear Information System (INIS)

Shyu, Jin-Cherng; Syu, Jhih-Zong

2014-01-01

In this study, the heat transfer of a plate-fin array cooled by a vibrating finger-like piezoelectric fan comprising four flexible rectangular blades was investigated. The results indicated that the heat transfer enhancement of the fin array cooled by a vibrating piezoelectric fan at x/L = 0.5 and H = 5 mm ranged between 1.5 and 3.3, regardless of the fin array orientation. However, the heat transfer enhancement caused by a fan being placed at either edge of the fin array yielded a dissimilar result between both of the fin array orientations because of the superimposed effects of the boundary layer development and the air flow induced by the fan. This dissimilarity was especially noticeable when the piezoelectric fan was composed of aluminum blades to accommodate the moderate Reynolds number. In addition to the Reynolds number, the ratio of the fan blade vibration envelope to the source area determined the Nu number of the piezoelectric fan-cooled fin array. This design enhanced the fin array heat transfer and reduced cooler volume by embedding multiple vibrating beams into the fin array. -- Highlights: • Heat transfer of a piezoelectric fan-cooled plate-fin array was investigated. • Effects of fan position, fan height and fan material on heat transfer were examined. • Similar heat transfer enhancement range was shown for both fin array orientations. • Fin heat transfer with a running Al fan at x = 0 was higher than that at x = 0.25L. • Besides fan Reynolds number, the area ratio also determined Nu of the fin array

A note on the heat transfer in convective fins

International Nuclear Information System (INIS)

Razelos, P.

1979-01-01

In this paper a generalized approach to the problem of heat transfer through convective fins is given. The proper dimensionless variables, which specify the general problem are identified, and upper bounds of the values of the dimensionless number Nsub(r) defined as 'the ratio of the heat transferred by the fin to that of the corresponding bare surface' are derived. It was shown that these limiting values of the Nsub(r) are 1/√B 1 and √2/B 1 for longitudinal fins and spines respectively, where B 1 is the Biot number hb/k, while for annular fins of constant thickness and hyperbolic profile, Nsub(r) 1 , where K(β) is a number determined by the profile of the fin and the ratio β = x 2 /x 1 of the outside to the inside radii. It was also shown that for longitudinal fins and spinces the possible adverse insulating effect by the use of the fin is avoided, if one selects the value of √hA/kC [de

Criteria for analysis and optimization of longitudinal fins with convective tip

International Nuclear Information System (INIS)

Gomes, E.S.

1983-01-01

The problem of heat transfer in longitudinal fins with the main geometries used in equipaments of heat transfer by convection is analyzed. The equation of energy is solved analytically of several geometries fins, with unidimensional formulation, through the use of the convective heat transfer coefficient. The problem of fin optimization is approached analytically yielding the parameters which allow the maximum heat transfer for each particular material waste in the fin. The use of the insulated tip model suggests the use of fins and its optimization for any Biot number of the fin. The use of the convective tip model allows us to determine when is vantageous or disadvantageous to use fins and when fin optimization is possible according to the value of the Biot number and to a convection parameter on the fin tip. (Author) [pt

Effet de la nutrition minérale azotée sur le gain en biomasse de l'if du canada et sur le contenu en taxanes

OpenAIRE

Jollez, Pierre-Antoine

2008-01-01

Dans le cadre d'un vaste programme de domestication de l'if du Canada (Taxus canadensis Marsh.) à des fins de production de taxanes, de jeunes plants en première, deuxième ou troisième années de culture en contenants ont été soumis à différentes sources d'azote (nitrate d'ammonium, nitrate de calcium, nitrate de sodium, sulfate d'ammonium et urée), appliquées à différentes doses, et à divers pH du substrat pour étudier leur influence sur la croissance des plants, sur la teneur en éléments min...

Actuation of a robotic fish caudal fin for low reaction torque

Science.gov (United States)

Yun, Dongwon; Kim, Kyung-Soo; Kim, Soohyun; Kyung, Jinho; Lee, Sunghee

2011-07-01

In this paper, a novel caudal fin for actuating a robotic fish is presented. The proposed caudal fin waves in a vertical direction with a specific spatial shape, which is determined by a so-called shape factor. For a specific shape factor, a traveling wave with a vertical phase difference is formed on a caudal fin during fin motion. It will be shown by the analysis that the maximum reaction torque at the joint of a caudal fin varies depending on the shape factors. Compared with a conventional plate type caudal fin, the proposed fin with a shape factor of 2π can eliminate the reaction torque perfectly, while keeping the propulsion force unchanged. The benefits of the proposed fin will be demonstrated by experiments.

The Mt Logan Holocene-late Wisconsinan isotope record

DEFF Research Database (Denmark)

Dahl-Jensen, Dorthe; Fisher, David; Osterberg, Erich

2008-01-01

Mt Logan • stable isotopes • Holocene • ENSO • peat • N Pacific • sudden change Udgivelsesdato: August......Mt Logan • stable isotopes • Holocene • ENSO • peat • N Pacific • sudden change Udgivelsesdato: August...

3D modeling of dual-gate FinFET.

Science.gov (United States)

Mil'shtein, Samson; Devarakonda, Lalitha; Zanchi, Brian; Palma, John

2012-11-13

The tendency to have better control of the flow of electrons in a channel of field-effect transistors (FETs) did lead to the design of two gates in junction field-effect transistors, field plates in a variety of metal semiconductor field-effect transistors and high electron mobility transistors, and finally a gate wrapping around three sides of a narrow fin-shaped channel in a FinFET. With the enhanced control, performance trends of all FETs are still challenged by carrier mobility dependence on the strengths of the electrical field along the channel. However, in cases when the ratio of FinFET volume to its surface dramatically decreases, one should carefully consider the surface boundary conditions of the device. Moreover, the inherent non-planar nature of a FinFET demands 3D modeling for accurate analysis of the device performance. Using the Silvaco modeling tool with quantization effects, we modeled a physical FinFET described in the work of Hisamoto et al. (IEEE Tran. Elec. Devices 47:12, 2000) in 3D. We compared it with a 2D model of the same device. We demonstrated that 3D modeling produces more accurate results. As 3D modeling results came close to experimental measurements, we made the next step of the study by designing a dual-gate FinFET biased at Vg1 >Vg2. It is shown that the dual-gate FinFET carries higher transconductance than the single-gate device.

Constructal design of finned tubes used in air-cooled heat exchangers

Energy Technology Data Exchange (ETDEWEB)

Shokouhmand, Hossein; Mahjoub, Shoeib [University of Tehran, Tehran (Iran, Islamic Republic of); Salimpour, Mohammad Reza [Isfahan University of Technology, Isfahan (Iran, Islamic Republic of)

2014-06-15

The present study documents the constructal design and optimization of finned tubes used in air-cooled heat exchangers. The considered tubes are equipped with annular fins. The aim is to minimize the overall thermal resistance by morphing the geometry. The geometrical and thermo-physical parameters considered are the number of fins, ratio of fin height to tube diameter, Stanton number, ratio of fin conductivity to air conductivity, ratio of in-tube fluid conductivity to air conductivity and dimensionless pressure drop. Two constraints are applied in the optimization process: fixed overall volume of heat exchanger and fixed volume fraction of fin material. It is found that there exist optimal values for the number and the height of fins. Moreover, the optimal heat transfer has an extremum in a special volume fraction of fin material.

Constructal design of finned tubes used in air-cooled heat exchangers

International Nuclear Information System (INIS)

Shokouhmand, Hossein; Mahjoub, Shoeib; Salimpour, Mohammad Reza

2014-01-01

The present study documents the constructal design and optimization of finned tubes used in air-cooled heat exchangers. The considered tubes are equipped with annular fins. The aim is to minimize the overall thermal resistance by morphing the geometry. The geometrical and thermo-physical parameters considered are the number of fins, ratio of fin height to tube diameter, Stanton number, ratio of fin conductivity to air conductivity, ratio of in-tube fluid conductivity to air conductivity and dimensionless pressure drop. Two constraints are applied in the optimization process: fixed overall volume of heat exchanger and fixed volume fraction of fin material. It is found that there exist optimal values for the number and the height of fins. Moreover, the optimal heat transfer has an extremum in a special volume fraction of fin material.

Computational thermal analysis of cylindrical fin design parameters and a new methodology for defining fin structure in LED automobile headlamp cooling applications

International Nuclear Information System (INIS)

Sökmen, Kemal Furkan; Yürüklü, Emrah; Yamankaradeniz, Nurettin

2016-01-01

Highlights: • In the study, cooling of LED headlamps in automotive is investigated. • The study is based on free convection cooling of LED module. • Besides free convection, Monte Carlo model is used as radiation model as well. • A new algorithm is presented for designing optimum fin structure. • Suggested algorithm for optimum design is verified by various simulations. - Abstract: In this study, the effects of fin design, fin material, and free and forced convection on junction temperature in automotive headlamp cooling applications of LED lights are researched by using ANSYS CFX 14 software. Furthermore a new methodology is presented for defining the optimum cylindrical fin structure within the given limits. For measuring the performance of methodology, analyses are carried out for various ambient temperatures (25 °C, 50 °C and 80 °C) and different LED power dissipations (0.5 W, 0.75 W, 1 W and 1.25 W). Then, analyses are repeated at different heat transfer coefficients and different fin materials in order to calculate LED junction temperature in order to see if the fin structure proposed by the methodology is appropriate for staying below the given safety temperature limit. As a result, the suggested method has always proposed proper fin structures with optimum characteristics for given LED designs. As another result, for safe junction temperature ranges, it is seen that for all LED power dissipations, adding aluminum or copper plate behind the printed circuit board at low ambient temperatures is sufficient. Also, as the ambient temperature increases, especially in high powered LED lights, addition of aluminum is not sufficient and fin usage becomes essential. High heat transfer coefficient and using copper fin affect the junction temperature positively.

Heat transfer enhancement for fin-tube heat exchanger using vortex generators

International Nuclear Information System (INIS)

Yoo, Seong Yeon; Park, Dong Seong; Chung, Min Ho; Lee, Sang Yun

2002-01-01

Vortex generators are fabricated on the fin surface of a fin-tube heat exchanger to augment the convective heat transfer. In addition to horseshoe vortices formed naturally around the tube of the fin-tube heat exchanger, longitudinal vortices are artificially created on the fin surface by vortex generators. The purpose of this study is to investigate the local heat transfer phenomena in the fin-tube heat exchangers with and without vortex generators, and to evaluate the effect of vortices on the heat transfer enhancement. Naphthalene sublimation technique is employed to measure local mass transfer coefficients, then analogy equation between heat and mass transfer is used to calculate heat transfer coefficients. Experiments are performed for the model of fin-circular tube heat exchangers with and without vortex generators, and of fin-flat tube heat exchangers with and without vortex generators. Average heat transfer coefficients of fin-flat tube heat exchanger without vortex generator are much lower than those of fin-circular tube heat exchanger. On the other hand, fin-flat tube heat exchanger with vortex generators has much higher heat transfer value than conventional fin-circular tube heat exchanger. At the same time, pressure losses for four types of heat exchanger is measured and compared

Numerical study of an innovative design of a finned double-pipe heat exchanger with variable fin-tip thickness

International Nuclear Information System (INIS)

Syed, K.S.; Ishaq, Muhammad; Iqbal, Zafar; Hassan, Ahmad

2015-01-01

Highlights: • Variable fin tip angle significantly effect the velocity and temperature distribution. • Significant gain in the thermal performance with decrease in the friction factor. • Variable fin tip angle must be considered an important parameter in designing finned annulus. - Abstract: The analysis of fully developed laminar convective heat transfer in an innovate design of a finned double-pipe heat exchanger (DPHE) with longitudinal fins of variable thickness of the tip subjected to the constant heat transfer rate boundary conditions is investigated here. The tip thickness is controlled by the ratio of tip to base angles as a parameter whose values varying from 0 to 1 correspond to the fin shapes varying from the triangular to the rectangular cross-section. Upto the knowledge of the authors, this parameter is being introduced for the first time in the literature. Discontinuous Galerkin finite element method (DG-FEM) has been employed in the present work. The overall performance of the proposed DPHE has been investigated by considering the friction factor, the Nusselt number and the j-factor. Upto 178% gain in the Nusselt number and 89% gain in the j-factor have been achieved relative to the rectangular cross-section. Such gains relative to the triangular cross-section are respectively 9.5% and 19%. The results indicate that the newly introduced parameter the ratio of tip to base angles has proved to play significant role in the design of a double-pipe heat exchanger in reducing the cost, weight and frictional loss, in improving the heat transfer rate and making the exchanger energy-efficient. Therefore, it must be considered as an important design parameter for heat exchanger design

High performance flexible CMOS SOI FinFETs

KAUST Repository

Fahad, Hossain M.; Sevilla, Galo T.; Ghoneim, Mohamed T.; Hussain, Muhammad Mustafa

2014-01-01

We demonstrate the first ever CMOS compatible soft etch back based high performance flexible CMOS SOI FinFETs. The move from planar to non-planar FinFETs has enabled continued scaling down to the 14 nm technology node. This has been possible due

De la prédication mendiante à la prédication protestante d’après une chronique du xvie siècle, celle d’Estienne Médicis, bourgeois du Puy

OpenAIRE

Courtemanche, Danielle

2015-01-01

La prédication des indulgences et les quêtes itinérantes dans le royaume de Castille, à la fin du Moyen Âge, occupent peu de place dans la production historiographique récente. Depuis les années 1950 et les travaux de José Goñi Gaztambide ou de Justo Fernández Alonso, le thème n’a plus été abordé que dans sa dimension économique à l’occasion de travaux consacrés au financement des campagnes contre les musulmans ou au développement de la fiscalité royale. Il serait pourtant erroné de penser qu...

Ice nucleating particles measured during the laboratory and field intercomparisons FIN-2 and FIN-3 by the diffusion chamber FRIDGE

Science.gov (United States)

Weber, Daniel; Schrod, Jann; Curtius, Joachim; Haunold, Werner; Thomson, Erik; Bingemer, Heinz

2016-04-01

The measurement of atmospheric ice nucleating particles (INP) is still challenging. In the absence of easily applicable INP standards the intercomparison of different methods during collaborative laboratory and field workshops is a valuable tool that can shine light on the performance of individual methods for the measurement of INP [1]. FIN-2 was conducted in March 2015 at the AIDA facility in Karlsruhe as an intercomparison of mobile instruments for measuring INP [2]. FIN-3 was a field campaign at the Desert Research Institutes Storm Peak Laboratory in Colorado in September 2015 [3]. The FRankfurt Ice nucleation Deposition freezinG Experiment (FRIDGE) participated in both experiments. FRIDGE measures ice nucleating particles by electrostatic precipitation of aerosol particles onto Si-wafers in a collection unit, followed by activation, growth, and optical detection of ice crystals on the substrate in an isostatic diffusion chamber [4,5]. We will present and discuss results of our measurements of deposition/condensation INP and of immersion INP with FRIDGE during FIN-2 and FIN-3. Acknowledgements: The valuable contributions of the FIN organizers and their institutions, and of the FIN Workshop Science team are gratefully acknowledged. Our work was supported by Deutsche Forschungsgemeinschaft (DFG) under the Research Unit FOR 1525 (INUIT) and the EU FP7-ENV- 2013 BACCHUS project under Grant Agreement 603445.

Holocene sea level, a semi-empirical contemplation

Science.gov (United States)

Bittermann, K.; Kemp, A.; Vermeer, M.; Rahmstorf, S.

2017-12-01

Holocene eustatic sea level from approximately -10,000-1800 CE was characterized by an increase of about 60m, with the rate progressively slowing down until sea level almost stabilizes between 500-1800 CE. Global and northern-hemisphere temperatures rose from the last glacial termination until the `Holocene Optimum'. From ­­there, up to the start of the recent anthropogenic rise, they almost steadily decline. How are the sea-level and temperature evolutions linked? We investigate this with semi-empirical sea-level models. We found that, due to the nature of Milankovitch forcing, northern-hemisphere temperature (we used the Greenland temperature by Vinther et al., 2009) is a better model driver than global mean temperature because the evolving mass of northern-hemisphere land ice was the dominant cause of Holocene global sea-level trends. The adjustment timescale for this contribution is 1200 years (900-1500 years; 90% confidence interval). To fit the observed sea-level history, the model requires a small additional constant rate (Bittermann 2016). This rate turns out to be of the same order of magnitude as reconstructions of Antarctic sea-level contributions (Briggs et al. 2014, Golledge et al. 2014). In reality this contribution is unlikely to be constant but rather has a dominant timescale that is large compared to the time considered. We thus propose that Holocene sea level can be described by a linear combination of a temperature driven rate, which becomes negative in the late Holocene (as Northern Hemisphere ice masses are diminished), and a positive, approximately constant term (possibly from Antarctica), which starts to dominate from the middle of the Holocene until the start of industrialization. Bibliography: Bittermann, K. 2016. Semi-empirical sea-level modelling. PhD Thesis University of Potsdam. Briggs, R.D., et al. 2014. A data-constrained large ensemble analysis of Antarctic evolution since the Eemian. Quaternary science reviews, 103, 91

Numerical simulation of heat exchangers elliptical tubes and corrugated fins

International Nuclear Information System (INIS)

Borrajo Pérez, Rubén; González Bayón, Juan José; Menéndez Pérez, Alberto

2015-01-01

The intensified heat exchangers fins are widely used in the automotive and domestic industry. The low heat transfer coefficients on the air side are the main reason why these fins of heat exchangers need to be intensified. In this paper, the numerical simulation of a wavy fin type is made with elliptical tubes. The dimensions of the fin is in the range of those used in air conditioning equipment. The friction factor and the mass transfer coefficient as a function of the Reynolds number for this type of fin, always within the laminar regime is determined. The numerical model against experimental results published in the literature is validated. In addition the mechanisms that produce intensified heat transfer fin in such occur. (full text)

Aux membres du personnel français détachés au CERN - French version only

CERN Multimedia

2003-01-01

Affiliation au régime de retraite français Le CERN a reçu la lettre suivante de la Mission permanente de la France auprès des Organisations Internationales à Genève au sujet de la récente publication d'un décret concernant la retraite des fonctionnaires français détachés dans les organisations internationales : " .. l'article 20 de la loi 2002-73 du 17 janvier 2002 a mis fin au caractère obligatoire de l'affiliation au régime de retraite français pour les fonctionnaires détachés à l'étranger ou dans les organisations internationales. Le décret 2002-1391 du 21 novembre 2002, publié au Journal Officiel du 28 novembre 2002, a prévu que les fonctionnaires concernés disposent d'un délai de quatre mois à partir de la notification de leur arrêté de détachement pour faire part à leur administration d'origine de leur volonté de continuer à cotiser au régime national. Pour les fonctionnaires ayant déjà reçu la notification de leur arrêté de détachement à la date du 1er décembre 20...

DETERMINATION OF THE TEMPERATURE DISTRIBUTION THE PERFORATED FINS UNDER

Directory of Open Access Journals (Sweden)

Aziz7 M. Mhamuad

2015-02-01

Full Text Available This work treats the problem of heat transfer for perforated fins under natural convection. The temperature distribution is examined for an array of rectangular fins (15 fins with uniform cross-sectional area (100x270 mm embedded with various vertical body perforations that extend through the fin thickness. The patterns of perforations include 18 circular perforations (holes. Experiments were carried out in an experimental facility that was specifically design and constructed for this purpose. The heat transfer rate and the coefficient of heat transfer increases with perforation diameter increased. 

Holocene fire dynamics in Fennoscandia

Science.gov (United States)

Clear, Jennifer; Seppa, Heikki; Kuosmanen, Niina; Molinari, Chiara; Lehsten, Veiko; Allen, Katherine; Bradshaw, Richard

2015-04-01

Prescribed burning is advocated in Fennoscandia to promote regeneration and to encourage biodiversity. This method of forest management is based on the perception that fire was much more frequent in the recent past and over a century of active fire suppression has created a boreal forest ecosystem almost free of natural fire. The absence of fire is thought to have contributed to the widespread dominance of Picea abies (Norway spruce) with the successive spruce dominated forest further reducing fire ignition potential. However, humans have altered the natural fire dynamics of Fennoscandia since the early- to mid-Holocene and disentangling the anthropogenic driven fire dynamics from the natural fire dynamics is challenging. Through palaeoecology and sedimentary charcoal deposits we are able to explore the Holocene spatial and temporal variability and changing drivers of fire and vegetation dynamics in Fennoscandia. At the local-scale, two forest hollow environments (history are compared to identify unique and mutual changes in disturbance history. Pollen derived quantitative reconstruction of vegetation at both the local- and regional-scale identifies local-scale disturbance dynamics and large-scale ecosystem response. Spatio-temporal heterogeneity and variability in biomass burning is explored throughout Fennoscandia and Denmark to identify the changing drives of fire dynamics throughout the Holocene. Palaeo-vegetation reconstructions are compared to process-based, climate driven dynamic vegetation model output to test the significance of fire frequency as a driver of vegetation composition and dynamics. Early-Holocene fire regimes in Fennoscandia are driven by natural climate variations and fuel availability. The establishment and spread of Norway spruce is driven by an increase in continentality of climate, but local natural and anthropogenic ecosystem disturbance may have aided this spread. The expansion of spruce led to a step-wise reduction in regional biomass

Chromium Is Elevated in Fin Whale (Balaenoptera physalus) Skin Tissue and Is Genotoxic to Fin Whale Skin Cells

Science.gov (United States)

Wise, Catherine F.; Wise, Sandra S.; Thompson, W. Douglas; Perkins, Christopher; Wise, John Pierce

2015-01-01

Hexavalent chromium (Cr(VI)) is present in the marine environment and is a known carcinogen and reproductive toxicant. Cr(VI) is the form of chromium that is well absorbed through the cell membrane. It is also the most prevalent form in seawater. We measured the total Cr levels in skin biopsies obtained from healthy free-ranging fin whales from the Gulf of Maine and found elevated levels relative to marine mammals in other parts of the world. The levels in fin whale biopsies ranged from 1.71 ug/g to 19.6 ug/g with an average level of 10.07 ug/g. We also measured the cytotoxicity and genotoxicity of Cr(VI) in fin whale skin cells. We found that particulate and soluble Cr(VI) are both cytotoxic and genotoxic to fin whale skin cells in a concentration-dependent manner. The concentration range used in our cell culture studies used environmentally relevant concentrations based on the biopsy measurements. These data suggest that Cr(VI) may be a concern for whales in the Gulf of Maine. PMID:25805270

Recherches géomorphologiques sur le Néogène du Sud du Pérou

Directory of Open Access Journals (Sweden)

1976-01-01

Full Text Available Pendant la première moitié du Miocène, un cycle d'érosion en partie contemporaine de la fin du volcanisme Tacaza achève l'aplanissement complet des Andes. Les produits de l'érosion se déposent en régime endoréique dans des bassins situés entre la Cordillère Occidentale et Ia chaîne côtière (formation Moquegua. Ainsi se développe une surface de régradation en direction de la Sierra ('Puna' et d'aggradation vers la niveau de base (Moquegua. Cette surface s'étend sur un domaine continental séparé du domaine pacifique par la chaîne côtière non encore aplanie. En effet, sur le flanc pacifique de celle-ci, on note la présence de sédiments continentaux (membre supérieur de la formation Camaná semblables à ceux de la formation Moquegua, mais les deux aires de sédimentation sont séparées par une ligne quasi-continue de reliefs côtiers. Ces reliefs sont en partie ennoyés en direction du Pacifique par les dépôts marins de la formation Pisco (Miocène supérieur, concordants sur le membre supérieur continental de la formation Camaná. Pendant ce même Miocène supérieur, se produit le soulèvement du voussoir andin, qui, en faisant basculer la surface de la Puna en direction du Pacifique, déclenche son rajeunissement par un nouveau cycle d'érosion en fonction d'un réseau hydrographique Incliné vers le nouveau niveau de base (celui de la transgression Pisco. Ce réseau hydrographique s'installe sur une couverture d'ignimbrites fossilisant la surface de la Puna et reposant en concordance avec la formation Moquegua. Ces ignimbrites datées de 14 à 15 millions d'années, confirment l'âge miocène de la surface de la Puna dans le Sud du Pérou. Pendant le Pliocène Inférieur l'abaissement du niveau de base vient ajouter ses effets à ceux du soulèvement des Andes et une phase générale de dissection du relief se développe en régime exoréique. Les formes dégagées par l'érosion différentielle sont d'une part des

Controverses institutionnelles et sociales autour du sang placentaire recueilli à des fins thérapeutiques1

OpenAIRE

Boileau, Claire

2003-01-01

Dans cet article, nous proposons d’exposer les résultats d’une recherche en anthropologie sociale et culturelle portant sur les enjeux du prélèvement de sang placentaire. Ce sang, riche en cellules souches, est prélevé au moment de l’accouchement sur des femmes ayant consenti au don. Il est ensuite traité puis stocké en attendant d’être greffé à des patients leucémiques. Appelé à se développer dans les années à venir, le prélèvement de cellules souches rencontre des difficultés de recueil non...

Paraître du deuil, d’un lieu à l’autre. Les veuves en Midi toulousain au XVIIIe siècle

Directory of Open Access Journals (Sweden)

Christine Dousset

2012-02-01

Full Text Available Sous l’Ancien Régime le veuvage oblige les femmes à changer d’apparence pour revêtir des habits de deuil, en particulier pendant l’année qui suit la mort du mari. À Toulouse, de la fin du XVIIe à la fin du XVIIIe siècle, se dessinent des permanences et des nouveautés qui apparaîtront de manière plus évidente dans la première partie du siècle suivant. L’importance symbolique de la tenue de la veuve est soulignée par l’obligation juridique faite aux héritiers du mari de lui fournir ses habits de deuil. Cependant, comme le montrent les inventaires après décès, les codes vestimentaires du deuil restent socialement discriminants, entre le respect d’une étiquette très élaborée par les veuves de la noblesse et les difficultés matérielles des femmes des milieux populaires urbains dont il est très difficile de préciser les pratiques. Ils se transforment cependant à la faveur des changements de la mode féminine et de la diffusion par l’imprimé, tel l’Almanach historique de la ville de Toulouse, du modèle parisien et curial dans les années 1780.Appearances of Mourning. The widows in Toulouse area in the Eighteenth century -During the "Ancien Regime", widowhood forced women to change their appearance to wear clothes of mourning, especially during the year following the death of their husband. In Toulouse, from the end of the Seventeenth century to the end of the Eightheenth century, we can see continuities and changes that will appear more prominently in the first part of the Nineteenth century. The legal obligation for the husband’s heirs to provide the widow’s « habits de deuil » shows the symbolic importance of mourning dress. However, as shown in the probate inventories, social groups use different mourning dress codes. The noble women must respect a very complicated etiquette whereas the women of the working classes are too poor and we don’t know exactly how they are dressed when they become

Holocene vegetation history from fossil rodent middens near Arequipa, Peru

Science.gov (United States)

Holmgren, C.A.; Betancourt, J.L.; Rylander, K.A.; Roque, J.; Tovar, O.; Zeballos, H.; Linares, E.; Quade, Jay

2001-01-01

Rodent (Abrocoma, Lagidium, Phyllotis) middens collected from 2350 to 2750 m elevation near Arequipa, Peru (16??S), provide an ???9600-yr vegetation history of the northern Atacama Desert, based on identification of >50 species of plant macrofossils. These midden floras show considerable stability throughout the Holocene, with slightly more mesophytic plant assemblages in the middle Holocene. Unlike the southwestern United States, rodent middens of mid-Holocene age are common. In the Arequipa area, the midden record does not reflect any effects of a mid-Holocene mega drought proposed from the extreme lowstand (100 m below modern levels, >6000 to 3500 yr B.P.) of Lake Titicaca, only 200 km east of Arequipa. This is perhaps not surprising, given other evidence for wetter summers on the Pacific slope of the Andes during the middle Holocene as well as the poor correlation of summer rainfall among modern weather stations in the central AndesAtacama Desert. The apparent difference in paleoclimatic reconstructions suggests that it is premature to relate changes observed during the Holocene to changes in El Nin??o Southern Oscillation modes. ?? 2001 University of Washington.

Atom-probe for FinFET dopant characterization

Energy Technology Data Exchange (ETDEWEB)

Kambham, A.K., E-mail: kambham@imec.be [K.U.Leuven, Instituut voor Kern-en Stralings fysika, Celestijnenlaan 200D, B-3001, Leuven (Belgium); IMEC, Kapeldreef 75, B-3001 Leuven (Belgium); Mody, J.; Gilbert, M.; Koelling, S.; Vandervorst, W. [K.U.Leuven, Instituut voor Kern-en Stralings fysika, Celestijnenlaan 200D, B-3001, Leuven (Belgium); IMEC, Kapeldreef 75, B-3001 Leuven (Belgium)

2011-05-15

With the continuous shrinking of transistors and advent of new transistor architectures to keep in pace with Moore's law and ITRS goals, there is a rising interest in multigate 3D-devices like FinFETs where the channel is surrounded by gates on multiple surfaces. The performance of these devices depends on the dimensions and the spatial distribution of dopants in source/drain regions of the device. As a result there is a need for new metrology approach/technique to characterize quantitatively the dopant distribution in these devices with nanometer precision in 3D. In recent years, atom probe tomography (APT) has shown its ability to analyze semiconductor and thin insulator materials effectively with sub-nm resolution in 3D. In this paper we will discuss the methodology used to study FinFET-based structures using APT. Whereas challenges and solutions for sample preparation linked to the limited fin dimensions already have been reported before, we report here an approach to prepare fin structures for APT, which based on their processing history (trenches filled with Si) are in principle invisible in FIB and SEM. Hence alternative solutions in locating and positioning them on the APT-tip are presented. We also report on the use of the atom probe results on FinFETs to understand the role of different dopant implantation angles (10{sup o} and 45{sup o}) when attempting conformal doping of FinFETs and provide a quantitative comparison with alternative approaches such as 1D secondary ion mass spectrometry (SIMS) and theoretical model values. -- Research highlights: {yields} This paper provides the information on how to characterize the FinFET devices using atom probe tomography (APT). {yields} Importance of this work is to assess the performance of these devices at different processing conditions by extracting the compositional profiles. {yields} The performance of these devices depends on the dimensions and the spatial distribution of dopants in source/drain regions

Atom-probe for FinFET dopant characterization

International Nuclear Information System (INIS)

Kambham, A.K.; Mody, J.; Gilbert, M.; Koelling, S.; Vandervorst, W.

2011-01-01

With the continuous shrinking of transistors and advent of new transistor architectures to keep in pace with Moore's law and ITRS goals, there is a rising interest in multigate 3D-devices like FinFETs where the channel is surrounded by gates on multiple surfaces. The performance of these devices depends on the dimensions and the spatial distribution of dopants in source/drain regions of the device. As a result there is a need for new metrology approach/technique to characterize quantitatively the dopant distribution in these devices with nanometer precision in 3D. In recent years, atom probe tomography (APT) has shown its ability to analyze semiconductor and thin insulator materials effectively with sub-nm resolution in 3D. In this paper we will discuss the methodology used to study FinFET-based structures using APT. Whereas challenges and solutions for sample preparation linked to the limited fin dimensions already have been reported before, we report here an approach to prepare fin structures for APT, which based on their processing history (trenches filled with Si) are in principle invisible in FIB and SEM. Hence alternative solutions in locating and positioning them on the APT-tip are presented. We also report on the use of the atom probe results on FinFETs to understand the role of different dopant implantation angles (10 o and 45 o ) when attempting conformal doping of FinFETs and provide a quantitative comparison with alternative approaches such as 1D secondary ion mass spectrometry (SIMS) and theoretical model values. -- Research highlights: → This paper provides the information on how to characterize the FinFET devices using atom probe tomography (APT). → Importance of this work is to assess the performance of these devices at different processing conditions by extracting the compositional profiles. → The performance of these devices depends on the dimensions and the spatial distribution of dopants in source/drain regions. → In this publication we

Study of Swept Angle Effects on Grid Fins Aerodynamics Performance

Science.gov (United States)

Faza, G. A.; Fadillah, H.; Silitonga, F. Y.; Agoes Moelyadi, Mochamad

2018-04-01

Grid fin is an aerodynamic control surface that usually used on missiles and rockets. In the recent several years many researches have conducted to develop a more efficient grid fins. There are many possibilities of geometric combination could be done to improve aerodynamics characteristic of a grid fin. This paper will only discuss about the aerodynamics characteristics of grid fins compared by another grid fins with different swept angle. The methodology that used to compare the aerodynamics is Computational Fluid Dynamics (CFD). The result of this paper might be used for future studies to answer our former question or as a reference for related studies.

Actes des 5èmes Journées Scientifiques du GDR3544 Sciences du Bois. Journées Annuelles du GDR 3544 Sciences du Bois

OpenAIRE

CHAPLAIN, Myriam; CARE, Sabine; GRIL, Joseph

2016-01-01

Le Groupement de Recherche en Sciences du bois (GDR3544 Sciences du Bois) a été créé en 2012 par le CNRS et renouvelé en 2016 pour 5 ans. La mission de ce groupement est : (1) de structurer la recherche sur le bois en France pour lui donner une visibilité nationale, (2) de contribuer au développement de la formation en sciences du bois et (3) de servir de relai aux réseaux internationaux de sciences du bois. Les 5èmes journées annuelles du GDR Bois ont été organisées à Bordeaux, au domaine du...

Optimization of Peripheral Finned-Tube Evaporators Using Entropy Generation Minimization

OpenAIRE

Pussoli, Bruno; Barbosa Jr., Jader; da Silva, Luciana; Kaviany, Massoud

2012-01-01

The peripheral finned-tube (PFT) is a new geometry for enhanced air-side heat transfer under moisture condensate blockage (evaporators). It consists of individual hexagonal (peripheral) fin arrangements with radial fins whose bases are attached to the tubes and tips are interconnected with the peripheral fins. In this paper, experimentally validated semi-empirical models for the air-side heat transfer and pressure drop are combined with the entropy generation minimization theory to determine ...

Correlated evolution of body and fin morphology in the cichlid fishes.

Science.gov (United States)

Feilich, Kara L

2016-10-01

Body and fin shapes are chief determinants of swimming performance in fishes. Different configurations of body and fin shapes can suit different locomotor specializations. The success of any configuration is dependent upon the hydrodynamic interactions between body and fins. Despite the importance of body-fin interactions for swimming, there are few data indicating whether body and fin configurations evolve in concert, or whether these structures vary independently. The cichlid fishes are a diverse family whose well-studied phylogenetic relationships make them ideal for the study of macroevolution of ecomorphology. This study measured body, and caudal and median fin morphology from radiographs of 131 cichlid genera, using morphometrics and phylogenetic comparative methods to determine whether these traits exhibit correlated evolution. Partial least squares canonical analysis revealed that body, caudal fin, dorsal fin, and anal fin shapes all exhibited strong correlated evolution consistent with locomotor ecomorphology. Major patterns included the evolution of deep body profiles with long fins, suggestive of maneuvering specialization; and the evolution of narrow, elongate caudal peduncles with concave tails, a combination that characterizes economical cruisers. These results demonstrate that body shape evolution does not occur independently of other traits, but among a suite of other morphological changes that augment locomotor specialization. © 2016 The Author(s). Evolution © 2016 The Society for the Study of Evolution.

Effets de la microdose sur la production du niébé, du mil et du ...

African Journals Online (AJOL)

Effets de la microdose sur la production du niébé, du mil et du sorgho en fonction la toposéquence. Fatimata Saba, Sibiri Jean Baptiste Taonda, Idriss Serme, Alimata A. Bandaogo, Augustin P. Sourwema, Adama Kabre ...

Fin de Copenhague

DEFF Research Database (Denmark)

Baumeister, Ruth

2016-01-01

FIN DE COPENHAGUE this book by the Danish Cobra artist Asger Jorn and the French philosopher Guy Debord, is the first in a series of two and was published in 1957, shortly before the authors founded the Situationist International. According to Jorn, upon arrival to Copenhagen, they stole some...

The optimization of longitudinal convective fins with internal heat generation

International Nuclear Information System (INIS)

Razelos, P.

1979-01-01

The solution of the optimization problem for longitudinal convective fins of constant thickness, triangular or parabolic profile, and uniform internal heat generation, is presented. The cases considered are those of a given heat generation density, total heat generation and heat generation per unit width of the fin, when either the heat dissipation or the width of the fin is prescribed. The results are set forth in a nondimensional form, which are presented graphically. The effect of the fin's thermal conductivity upon the optimum dimensions is discussed, and limiting values for the heat generation and the heat dissipation, which may be imposed on the fin for a feasible optimization, are also obtained. (Auth.)

Early-Holocene decoupled summer temperature and monsoon precipitation in southwest China

Science.gov (United States)

Wu, D.; Chen, F.; Chen, X.; Lv, F.; Zhou, A.; Chen, J.; Abbott, M. B.; Yu, J.

2017-12-01

Proxy based reconstructions of Holocene temperature have shown that both the timing and magnitude of the thermal maximum vary substantially between different regions; the simulations results from climate models also show that summers were substantially cooler over regions directly influenced by the presence of the Laurentide ice sheet during the early Holocene, whereas other regions of the Northern Hemisphere were dominated by orbital forcing. However, for lack of summer temperature reconstruction in the low latitude regions like southwestern China dominated by the Indian summer monsoon, the Holocene summer temperature variations and it underlying forcing mechanism are ambiguous. Here we present a well-dated record of pollen-based quantitative summer temperature (mean July; MJT) over the last 14000 years from Xingyun Lake, Yunnan Province, southwest China. It was found that MJT decreased during the YD event, then increased slowly until 7400 yr BP, and decreased thereafter. The MJT shows a pattern with middle Holocene maximum of MJT, indicating a different changing pattern with the carbonate oxygen isotope record (d18O) from the same core during the early Holocene (11500-7400 yr BP), which has the similar variation with speleothem d18O record from Dongge cave, both indicate the variation of monsoon precipitation with the highest precipitation occurred during the early Holocene. Therefore, we propose that the variation of summer temperature and precipitation in southwest China was decoupled during the early Holocene. However, both MJT and monsoon precipitation decreased after the middle Holocene following the boreal summer insolation. We suggest that the high precipitation with strong summer monsoon and hence higher cloud cover may depress the temperature increasing forced by increasing summer insolation during the early Holocene; while melting ice-sheet in the high latitude regions had strongly influenced the summer temperature increase during the deglacial period

Mike Davis, Génocides tropicaux. Catastrophes naturelles et famines coloniales (1870-1900. Aux origines du sous-développement, Paris, La Découverte, 2003, 479 p., trad. Late Victorian Holocausts, El Niño Famines and the Making of the Third World, 2001.

Directory of Open Access Journals (Sweden)

Cyrille Ferraton

2005-04-01

Full Text Available C’est à une histoire en grande partie négligée et méconnue qu’est consacré l’ouvrage de Mike Davis Génocides tropicaux publié en 2001 sous le titre Late Victorian Holocausts, El Niño Famines and the Making of the Third World. L’Inde, la Chine, le Brésil, l’Afrique du Nord, l’Afrique australe, les Philippines, en fait, un grand nombre de pays qu’Alfred Sauvy désignera en 1952 par pays du « tiers-monde », connurent à la fin du XIXe siècle et au tout début du XXe siècle trois périodes climatique...

Research on dynamic characteristics of new chaotic-advection fins

International Nuclear Information System (INIS)

Kong Songtao; Dong Qiwu; Liu Minshan; Zhu Qing

2007-01-01

Analysis and the numerical simulation has confirmed that the flow is of the chaotic advection in the flow channel of the new fin. The chaotic advection results in stronger mixing under low Re, and thus enhances the heat transfer and anti-scaling ability. The new fin provides the beneficial exploration to the concept of chaotic advection which applies to the plate-fin heat exchanger. (authors)

Stress analysis of plate-fin structures in recuperator

International Nuclear Information System (INIS)

Matsui, Shingo; Muto, Yasushi; Shiina, Yasuaki

2001-01-01

A high performance compact recuperator with 95% effectiveness is required to achieve a high thermal efficiency power generation of up to 50% in High Temperature Gas Cooled Reactor (HTGR) coupled with closed cycle helium gas turbine. Though a plate-fin type heat exchanger is proposed for this recuperator, much research and development works are needed to establish this high performance goal since there exists no state-of-the-art technology in such a high pressure and high temperature one. One of the important works is to establish the structural analysis and evaluation method in this plate-fin type heat exchanger. This paper describes the results of stress analysis of the plate-fin structure under the internal pressure as the first step of this work. First, the modeling of a unit plate-fin structure for the analysis was examined and a three layers model was confirmed to be most adequate. The stress distribution within the structure was clarified by using this model. Second, the three layers model was simplified to one layer model with sufficient accuracy. By using this model, both the effects of an inclined angle of fin and a thickness of separate on the strength were examined parametrically. Under the relevant design conditions, it was revealed that the optimum inclined angle of fin locates in the neighborhood of 76 degree rather than most difficult fabrication angle 90 degree and there is possibility to adopt thinner thickness than 0.5 mm in the current design. (author)

Strain characterization of FinFETs using Raman spectroscopy

International Nuclear Information System (INIS)

Kaleli, B.; Hemert, T. van; Hueting, R.J.E.; Wolters, R.A.M.

2013-01-01

Metal induced strain in the channel region of silicon (Si) fin-field effect transistor (FinFET) devices has been characterized using Raman spectroscopy. The strain originates from the difference in thermal expansion coefficient of Si and titanium-nitride. The Raman map of the device region is used to determine strain in the channel after preparing the device with the focused ion beam milling. Using the Raman peak shift relative to that of relaxed Si, compressive strain values up to – 0.88% have been obtained for a 5 nm wide silicon fin. The strain is found to increase with reducing fin width though it scales less than previously reported results from holographic interferometry. In addition, finite-element method (FEM) simulations have been utilized to analyze the amount of strain generated after thermal processing. It is shown that obtained FEM simulated strain values are in good agreement with the calculated strain values obtained from Raman spectroscopy. - Highlights: ► Strain is characterized in nanoscale devices with Raman spectroscopy. ► There is a fin width dependence of the originated strain. ► Strain levels obtained from this technique is in correlation with device simulations

L'administration du travail et la production du droit du travail (1906-1960). : Note de synthèse du rapport de recherche

OpenAIRE

Le Crom , Jean-Pierre

2007-01-01

Synthèse d'un rapport de recherche dont l'objectif est d'appréhender le rôle de l'administration centrale du travail dans la production du droit du travail. Deux dimensions sont explorées : le profil des rédacteurs et l'organisation des structures.

The Influence of Culture on the International Management of Shark Finning

Science.gov (United States)

Dell'Apa, Andrea; Chad Smith, M.; Kaneshiro-Pineiro, Mahealani Y.

2014-08-01

Shark finning is prohibited in many countries, but high prices for fins from the Asian market help maintain the international black-market and poaching. Traditional shark fin bans fail to recognize that the main driver of fin exploitation is linked to cultural beliefs about sharks in traditional Chinese culture. Therefore, shark finning should be addressed considering the social science approach as part of the fishery management scheme. This paper investigates the cultural significance of sharks in traditional Chinese and Hawaiian cultures, as valuable examples of how specific differences in cultural beliefs can drive individuals' attitudes toward the property of shark finning. We suggest the use of a social science approach that can be useful in the design of successful education campaigns to help change individuals' attitudes toward shark fin consumption. Finally, alternative management strategies for commercial fishers are provided to maintain self-sustainability of local coastal communities.

A Holocene temperature reconstruction from northern New Zealand: a test of North Atlantic Holocene climate patterns as a global template

Science.gov (United States)

van den Bos, Valerie; Rees, Andrew; Newnham, Rewi; Augustinus, Paul

2017-04-01

Holocene climate variability has been well defined in the North Atlantic (Walker et al., 2012), but the global extent of this climate change stratigraphy is debatable. If the North Atlantic serves as a global template for Holocene climate, then New Zealand (NZ) is ideally positioned to test this assertion, as it is distal from the northern drivers. Additionally, it is one of the few landmasses in the Southern Hemisphere that is influenced by both sub-tropical and extra-tropical climatic regimes, which may be more important controls in the southern mid-latitudes. Although much work has been done to characterise the Holocene in NZ using pollen, most of these records lack the resolution or sensitivity to determine whether abrupt or short-lived events occurred. The NZ-INTIMATE climate event stratigraphy lacks a type section for the Holocene (Alloway et al., 2007). Records from northern NZ typically show little change, other than a possible early Holocene warming. Here, we present a combined pollen and chironomid temperature reconstruction from Lake Pupuke (northern NZ), the first of its kind in NZ that covers the entire Holocene. By comparing mean annual temperatures reconstructed from fossil pollen and mean summer temperatures inferred from chironomid remains, we can assess changes in seasonality. Mean summer temperature was reconstructed from the chironomid record using a weighted averaging partial least squares (WA-PLS) model (n comp = 2, r2booth = 0.77, RMSEP = 1.4°C) developed from an expanded version of Dieffenbacher-Krall et al. (2007)'s chironomid training set. Preliminary results show evidence for cool summers during the early Holocene as well as around the period of the Little Ice Age as defined in the North Atlantic region. These and other climate patterns determined from the Pupuke chironomid and pollen records will be compared with other evidence from northern New Zealand and with the North Atlantic record of Holocene climate variability. References

情报研究在FinTech实践中的应用展望%The Application Prospect of Information Science in FinTech Practice

Institute of Scientific and Technical Information of China (English)

徐扬; 刘姝雯; 腾菲; 罗晶

2017-01-01

[目的/意义]针对金融科技(FinTech)发展的特征、现状及问题,探究情报学知识和技术在FinTech实践中的应用和发展方向.[方法/过程]梳理Fintech概念在国内外的发展历程和现状,并从情报学视角,讨论FinTech在特征、应用、监管等方面的研究展望,提出相应的建议.[结果/结论]研究结果表明,情报学与FinTech相辅相成,共同发展.未来,可以进一步强化FinTech业务的信息化与数字化,加强情报分析、商务智能以及情报学视角的大数据分析,为FinTech的发展注入更多的活力.

Effet du Pediococcus acidilactici sur le bilan lipidique sanguin du ...

African Journals Online (AJOL)

Les résultats relatifs aux performances zootechniques ont montré que l'addition du probiotique a amélioré significativement le gain de poids pendant la phase de croissance se traduisant par un indice de consommation meilleur. Les dosages du cholestérol total, des triglycérides, du HDL et du LDL ont été déterminés à la ...

Forced convection heat transfer correlation for finned plates in a duct

International Nuclear Information System (INIS)

Chae, Myeong-Seon; Moon, Je-Young; Chung, Bum-Jin

2014-01-01

Forced convection heat transfer experiments were conducted for plate-fin in a duct using various fin spacing, fin height, duct width, Reynolds number for Prandtl numbers 2,014. Based upon analogy concept, mass transfer rate were measured instead of heat transfer rates. The heat transfer rates were enhanced with the increase of fin height and decrease of fin spacing as they increase the heat transfer area. Meanwhile, heat transfer rates were impaired with the increase of the duct width as the bypass flows increased to tip clearance region. Forced convection heat transfer correlations were developed for laminar and turbulent flow conditions and for narrow and wide ducts. The work draws attention to the tip clearance on the heat transfer of the finned plate in a duct. (author)

Le débat sur l’euthanasie et les pratiques en fin de vie en France et en Allemagne. Une étude comparative

Directory of Open Access Journals (Sweden)

Ruth Horn

2009-12-01

Full Text Available Ce travail a pour objectif de comprendre comment la question morale du droit de déterminer le moment de sa mort émerge dans une société et comment elle est abordée, notamment dans deux pays, la France et l’Allemagne, qui interdisent l’euthanasie. En effet, bien que dans les pays occidentaux, les médecins et les patients rencontrent des problèmes semblables face à une situation de maladie grave ou de fin de vie, chaque société a son histoire propre avec des spécificités en matière de normes pr...

Externally finned circular tube immerse in a phase-change material

International Nuclear Information System (INIS)

Alves, C.L.F.; Ismail, K.A.R.

1985-01-01

In an attempt to increase the heat transfer rate and reduce the convective currents during the freezing of phase change materials (PCM) in storage tanks, externally finned circular tubes are studied experimentally. The parameters analysed in this work include number of fins, fin length, initial degree of superheat and freezing time

Investigation of thermal effects on FinFETs in the quasi-ballistic regime

Science.gov (United States)

Yin, Longxiang; Shen, Lei; Di, Shaoyan; Du, Gang; Liu, Xiaoyan

2018-04-01

In this work, the thermal effects of FinFETs in the quasi-ballistic regime are investigated using the Monte Carlo method. Bulk Si nFinFETs with the same fin structure and two different gate lengths L g = 20 and 80 nm are investigated and compared to evaluate the thermal effects on the performance of FinFETs in the quasi-ballistic regime. The on current of the 20 nm FinFET with V gs = 0.7 V does not decrease with increasing lattice temperature (T L) at a high V ds. The electrostatic properties in the 20 nm FinFET are more affected by T L than those in the 80 nm FinFET. However, the electron transport in the 20 nm FinFET is less affected by T L than that in the 80 nm FinFET. The electrostatic properties being more sensitive and the electron transport being less sensitive to thermal effects in the quasi-ballistic regime than in the diffusive regime should be considered for effective device modeling and design.

Alimentation du nouveau-ne et du nourrisson dans la region ...

African Journals Online (AJOL)

Alimentation du nouveau-ne et du nourrisson dans la region centrale du togo : pratiques familiales et communautaires avant la mise en oeuvre de la strategie « prise en charge integree des maladies de l'enfant »

Self-propelled heaving and pitching flexible fin in a quiescent flow

International Nuclear Information System (INIS)

Kim, Boyoung; Park, Sung Goon; Huang, Weixi; Sung, Hyung Jin

2016-01-01

Highlights: • A self-propelled flexible fin with heaving and pitching motions in a quiescent flow has been simulated by using the penalty immersed boundary method. • The cruising speed and the swimming efficiency of the self-propelled fin were determined as functions of the bending coefficient (γ), the heaving amplitude (A_h). • We optimized the cruising speed and the swimming efficiency with respect to γ, f, A_h, A_p, and Δϕ. - Abstract: A self-propelled flexible fin with heaving and pitching motions in a quiescent flow has been simulated by using the penalty immersed boundary method. The flexible fin can move freely in the horizontal direction and the body of the flexible fin moves passively along with the active head motion. The position of the head of the fin was described as a harmonic heaving oscillation in the vertical direction, while the inclination angle of the head was prescribed as a harmonic oscillation with a moving clamped condition for the heaving and pitching fin. The cruising speed and the swimming efficiency of the self-propelled fin were determined as functions of the bending stiffness (γ), the heaving amplitude (A_h), the pitching amplitude (A_p), the flapping frequency (f) and the phase difference (Δϕ) between A_h and A_p. We optimized the cruising speed and the swimming efficiency with respect to γ, f, A_h, A_p and Δϕ. For a certain range of A_p, the swimming efficiency of the heaving and pitching fin is larger than that of a heaving-only fin.

Vortex Shedding from Finned Circular Cylinders

Science.gov (United States)

1980-11-01

FINNED CIRCULAR CYLINDERSo ,rm"" 1..UTNOI .)R*., r. *.040, 111SPOR- / T NuMBII f.John G. elute asOHans J.’/, ugt -. . . , ,<-. -. ,:. =., .. Siil P3RPIO...fins and other sharp protuberances. These purely two-dimensional flows then may be used in a strip theory to include at least some aspects of three...boundary- layer theory . Such a prediction method, together with a technique to provide for a vortex sheet at the separation point, will be included in

Highly flexible SRAM cells based on novel tri-independent-gate FinFET

Science.gov (United States)

Liu, Chengsheng; Zheng, Fanglin; Sun, Yabin; Li, Xiaojin; Shi, Yanling

2017-10-01

In this paper, a novel tri-independent-gate (TIG) FinFET is proposed for highly flexible SRAM cells design. To mitigate the read-write conflict, two kinds of SRAM cells based on TIG FinFETs are designed, and high tradeoff are obtained between read stability and speed. Both cells can offer multi read operations for frequency requirement with single voltage supply. In the first TIG FinFET SRAM cell, the strength of single-fin access transistor (TIG FinFET) can be flexibly adjusted by selecting five different modes to meet the needs of dynamic frequency design. Compared to the previous double-independent-gate (DIG) FinFET SRAM cell, 12.16% shorter read delay can be achieved with only 1.62% read stability decrement. As for the second TIG FinFET SRAM cell, pass-gate feedback technology is applied and double-fin TIG FinFETs are used as access transistors to solve the severe write-ability degradation. Three modes exist to flexibly adjust read speed and stability, and 68.2% larger write margin and 51.7% shorter write delay are achieved at only the expense of 26.2% increase in leakage power, with the same layout area as conventional FinFET SRAM cell.

Holocene Evolution of Qing'ao Embayment, Southern China

Science.gov (United States)

Switzer, A. D.; Yu, F.; Chen, B.; Zheng, Z.; Wang, D.

2012-12-01

The Holocene evolution of the Qing'ao embayment, Nan'ao Island, southern China, is primarily the result of the interaction of tectonic activity, climate variation and changes in relative sea level. Characterizing the evolutionary history of the relatively small Qing'ao embayment during the Holocene will help improve our understanding of the driving mechanisms of coastal evolution in the area. To reconstruct the Holocene evolution history we analyzed the grain size, loss on ignition (LOI) and carbonate content of modern and core samples. Modern environmental analogs were examined in surface samples ranging from the coastal sand dunes through to offshore. The results of these modern samples suggest that dune sand (mean size of ~2.33Phi) are slightly finer than beach sand (mean size of 2.13Phi), and nearshore sediment is much coarser than offshore sediment (mean size of 5.90Phi). This modern analogs were then applied to 8 percussion cores from the Qing'ao embayment. A chronological framework obtained from 11 radiocarbon samples suggests that the embayment started to accept deposition since early Holocene, ~8500 cal. yr. BP. Three main phases of Holocene evolution were identified. A basin wide shell-rich sand sheet forms the basal Holocene facies and overlies clay rich presumably Pleistocene sediments or bedrock. This facies records an initial sedimentation phase associated with the early Holocene transgression into the embayment (~8500-6000 cal. yr. BP). The basal facies grades upward to a mixed sandy-mud facies which includes lagoonal clayey-silts, flood tide delta sands and records an estuarine phase lasting from ~6000-1000 cal. yr. BP that appears coincident with falling regional sea levels. Coincident with the estuarine phase is a period of coastal dune building recorded as yet undated massive sands that are found in the upper fill. Toward the end of the estuarine phase it is apparent that dune migration has restricted the lagoon entrance and that this was

Holocene Sea-Level Database For The Caribbean Region

Science.gov (United States)

Khan, N. S.; Horton, B.; Engelhart, S. E.; Peltier, W. R.; Scatena, F. N.; Vane, C. H.; Liu, S.

2013-12-01

Holocene relative sea-level (RSL) records from far-field locations are important for understanding the driving mechanisms controlling the nature and timing of the mid-late Holocene reduction in global meltwaters and providing background rates of late Holocene RSL change with which to compare the magnitude of 20th century RSL rise. The Caribbean region has traditionally been considered far-field (i.e., with negligible glacio-isostatic adjustment (GIA) influence), although recent investigations indicate otherwise. Here, we consider the spatial variability in glacio-isostatic, tectonic and local contributions on RSL records from the circum-Caribbean region to infer a Holocene eustatic sea-level signal. We have constructed a database of quality-controlled, spatially comprehensive, Holocene RSL observations for the circum-Caribbean region. The database contains over 500 index points, which locate the position of RSL in time and space. The database incorporates sea-level observations from a latitudinal range of 5°N to 25°N and longitudinal range of 55°W to 90°W. We include sea-level observations from 11 ka BP to present, although the majority of the index points in the database are younger than 8 ka BP. The database is sub-divided into 13 regions based on the distance from the former Laurentide Ice Sheet and regional tectonic setting. The index points were primarily derived from mangrove peat deposits, which in the Caribbean form in the upper half of the tidal range, and corals (predominantly Acropora palmata), the growth of which is constrained to the upper 5 m of water depth. The index points are classified on the basis of their susceptibility to compaction (e.g., intercalated, basal). The influence of temporal changes in tidal range on index points is also considered. The sea-level reconstructions demonstrate that RSL did not exceed the present height (0 m) during the Holocene in the majority of locations, except at sites in Suriname/Guayana and possibly Trinidad

Clinal variation of some mammals during the Holocene in Missouri

Science.gov (United States)

Purdue, James R.

1980-03-01

Eastern cottontail ( Sylvilagus floridanus), fox squirrel ( Sciurus niger), and gray squirrel ( Sciurus carolinensis) were examined for clinal variation during the Holocene. Modern samples of all three species displayed strong east-west patterns along the western edge of the eastern deciduous forest: S. floridanus and S. niger decrease and S. carolinensis increases in size. Archeological samples of S. carolinensis from Rodgers Shelter (23BE125), Benton County, Missouri, and Graham Cave (23MT2), Montgomery County, Missouri, indicated an increase in size from early to middle Holocene. Sylvilagus floridanus from Rodgers Shelter decreased in size from early to middle Holocene and then increased during the late Holocene to modern proportions. A literature survey reveals that clinal variation is a common phenomenon among modern homeotherms. In introduced species, clinal variation has developed after relatively few generations, indicating rapid adaptations to environmental conditions; often winter climatic variables are implicated. Morphological variation in the study species during the Holocene is interpreted as a response to changing climates. Studies of morphological clines may lead to another valuable data source for reconstructing past ecologies.

Portage vaginal du streptocoque du groupe B chez la femme ...

African Journals Online (AJOL)

Introduction: le streptocoque du groupe B est le principal agent impliqué dans les infections materno-fœtales, les septicémies et les méningites du nouveau-né à terme. L'objectif est de déterminer le taux de portage maternel du streptocoque du groupe B (SGB) à terme. Méthodes: un prélèvement vaginal a été réalisé de ...

Étude comparée du Liber Judiciorum et du Fuero Juzgo

Directory of Open Access Journals (Sweden)

Estelle MAINTIER-VERMOREL

2009-04-01

Full Text Available Étant donné sa situation géographique, entre l’Europe et le monde arable, la Castille a joué un rôle particulièrement important, au Moyen Âge, dans le cadre des activités de traduction - notamment avec la célèbre École de Tolède ou les ateliers d’Alphonse X. Cette étude est centrée sur l’une de ces traductions, réalisée sous le règne de Ferdinand III, qui a représenté un point de départ dans le passage des textes officiels du latin au romance. Il s’agit du Fuero Juzgo, un ensemble de lois octroyé, pour la première fois, par Ferdinand III en 1241 à la ville de Cordoue et présenté comme la simple traduction du Liber Judiciorum, élaboré cinq siècles plus tôt dans les Conciles wisigothiques. Nous n’aborderons pas ici cette traduction d’un point de vue linguistique, mais historique et politique. Par le biais d’une comparaison détaillée des prologues des deux textes - qui constituent de véritables traités politiques portant sur le rôle du roi et ses relations avec l’Eglise - nous tenterons de démontrer comment le texte a pu être adapté, au travers de changements minimes mais nombreux et systématiques. Nous essaierons également de montrer pourquoi, dans un contexte de réunion entre Castille et León et également de grande extension du territoire, due à la Reconquête, cette réélaboration subtile du contenu peut être imputée à une manipulation à des fins politiques. Une manipulation, qui plus est, dotée d’une orientation très claire, c’est-à-dire en faveur du roi et au détriment de l’Église - un phénomène qui pourrait constituer les prémices de ce que l’on a coutume d’appeler la genèse de l’État moderne.Dada su situación geográfica, entre Europa y el mundo árabe, Castilla tuvo un papel particularmente importante en el marco de las actividades de traducción durante la Edad Media - especialmente con la famosa Escuela de Toledo o los talleres de Alfonso

The Cx43-like connexin protein Cx40.8 is differentially localized during fin ontogeny and fin regeneration.

Directory of Open Access Journals (Sweden)

Sarah V Gerhart

Full Text Available Connexins (Cx are the subunits of gap junctions, membraneous protein channels that permit the exchange of small molecules between adjacent cells. Cx43 is required for cell proliferation in the zebrafish caudal fin. Previously, we found that a Cx43-like connexin, cx40.8, is co-expressed with cx43 in the population of proliferating cells during fin regeneration. Here we demonstrate that Cx40.8 exhibits novel differential subcellular localization in vivo, depending on the growth status of the fin. During fin ontogeny, Cx40.8 is found at the plasma membrane, but Cx40.8 is retained in the Golgi apparatus during regeneration. We next identified a 30 amino acid domain of Cx40.8 responsible for its dynamic localization. One possible explanation for the differential localization is that Cx40.8 contributes to the regulation of Cx43 in vivo, perhaps modifying channel activity during ontogenetic growth. However, we find that the voltage-gating properties of Cx40.8 are similar to Cx43. Together our findings reveal that Cx40.8 exhibits differential subcellular localization in vivo, dependent on a discrete domain in its carboxy terminus. We suggest that the dynamic localization of Cx40.8 differentially influences Cx43-dependent cell proliferation during ontogeny and regeneration.

Hydrodynamical analysis of the effect of fish fins morphology

Science.gov (United States)

Azwadi Che Sidik, Nor; Yen, Tey Wah

2013-12-01

The previous works on the biomechanics of fishes focuses on the locomotion effect of the fish bodies. However, there is quite a insufficiency in unveiling the respective function of fins when the fishes pose statics and exposed to fluid flow. Accordingly, this paper's focus is to investigate the hydrodynamic effect of the fins configuration to the fluid flow of shark-shaped-inspired structure. The drag and lift coefficient is computed for different cases of fish fins addition and configuration. The k-epsilon turbulence model is deployed using finite volume method with the aid of commercial software ANSYS CFX. The finding will demystify some of the functions of the fish's fins in term of their contribution to the hydrodynamic flow around the fishes.

Les anophèles et la transmission du paludisme à Ambohimena, village de la marge occidentale des Hautes-Terres Malgaches

Directory of Open Access Journals (Sweden)

Rajaonarivelo V.

2004-03-01

Full Text Available Une étude a été menée dans le Moyen-Ouest de Madagascar à 940 mètres d'altitude dans le village d'Ambohimena. Ce village est situé en dehors de la zone d'aspersions intra-domiciliaires d'insecticides rémanents. Deux vecteurs, An. funestus Giles, 1900 et An. arabiensis Patton, 1905 y sont présents. An. funestus est abondant au cours de la saison chaude et humide, avec deux pics d'abondance en décembre et avril. L'endophagie d' An. funestus est faible (taux d'endophagie = 35,3 % . C'est une espèce endophile (Taux d'endophilie = 78 % et anthropophile (taux d'anthropophilie = 64 %. Son infectivité est faible (taux d'infectivité = 0,20 %. Le taux d'inoculation spécifique de Plasmodium falciparum par l'espèce An. funestus a été de moins de 10 piqûres par homme et par an. Cette espèce présente une capacité vectrice maximale à la fin du premier tour de riz (janvier alors que son abondance maximale est observée à la fin du deuxième tour (avril-mai An. arabiensis est abondant entre décembre et janvier et est lié à la présence des gîtes pluviaux favorables au développement larvaire. C'est une espèce exophage (taux d'endophagie = 27,5 % et zoophile (taux d'anthropophilie = 7,8 %. An. arabiensis jouerait un rôle secondaire dans la transmission du paludisme car la présence des plasmodies n'a pas été mise en évidence (effectif testé = 871. Dans ce village, la stabilité du paludisme est modérée ou intermédiaire ; plus proche de l'instabilité que de la stabilité avérée. Il est suggéré que la lutte antivectorielle soit étendue aux zones de transition stabilité-instabilité qui constitueraient un réservoir de vecteurs et de plasmodies, afin de prévenir l'émergence de nouvelles épidémies sur les Hautes-Terres.

On the Hydrodynamics of Anomalocaris Tail Fins.

Science.gov (United States)

Sheppard, K A; Rival, D E; Caron, J-B

2018-04-25

Anomalocaris canadensis, a soft-bodied stem-group arthropod from the Burgess Shale, is considered the largest predator of the Cambrian period. Thanks to a series of lateral flexible lobes along its dorso-ventrally compressed body, it is generally regarded as an efficient swimmer, well-adapted to its predatory lifestyle. Previous theoretical hydrodynamic simulations have suggested a possible optimum in swimming performance when the lateral lobes performed as a single undulatory lateral fin, comparable to the pectoral fins in skates and rays. However, the role of the unusual fan-like tail of Anomalocaris has not been previously explored. Swimming efficiency and maneuverability deduced from direct hydrodynamic analysis are here studied in a towing tank facility using a three-vane physical model designed as an abstraction of the tail fin. Through direct force measurements, it was found that the model exhibited a region of steady-state lift and drag enhancement at angles of attack greater than 25° when compared to a triangular-shaped reference model. This would suggest that the resultant normal force on the tail fin of Anomalocaris made it well-suited for turning maneuvers, giving it the ability to turn quickly and through small radii of curvature. These results are consistent with an active predatory lifestyle, although detailed kinematic studies integrating the full organism, including the lateral lobes, would be required to test the effect of the tail fin on overall swimming performance. This study also highlights a possible example of evolutionary convergence between the tails of Anomalocaris and birds, which, in both cases, are well-adapted to efficient turning maneuvers.

Performance and optimum design of convective-radiative rectangular fin with convective base heating, wall conduction resistance, and contact resistance between the wall and the fin base

International Nuclear Information System (INIS)

Aziz, Abdul; Beers-Green, Arlen B.

2009-01-01

This paper investigates the performance and optimum design of a longitudinal rectangular fin attached to a convectively heated wall of finite thickness. The exposed surfaces of the fin lose heat to the environmental sink by simultaneous convection and radiation. The tip of the fin is assumed to lose heat by convection and radiation to the same sink. The analysis and optimization of the fin is conducted numerically using the symbolic algebra package Maple. The temperature distribution, the heat transfer rates, and the fin efficiency data is presented illustrating how the thermal performance of the fin is affected by the convection-conduction number, the radiation-conduction number, the base convection Biot number, the convection and radiation Biot numbers at the tip, and the dimensionless sink temperature. Charts are presented showing the relationship between the optimum convection-conduction number and the optimum radiation-conduction number for different values of the base convection Biot number and dimensionless sink temperature and fixed values of the convection and radiation Biot numbers at the tip. Unlike the few other papers which have applied the Adomian's decomposition and the differential quadrature element method to this problem but give illustrative results for specific fin geometry and thermal variables, the present graphical data are generally applicable and can be used by fin designers without delving into the mathematical details of the computational techniques.

Mid-Holocene to Present Climate Transition in Tropical South America

Science.gov (United States)

Turcq, B.; Cordeiro, R.; Sifeddine, A.; Braconnot, P.; Dias, P. S.; Costa, R.; Jorgetti, T.

2008-12-01

The classical illustration of Holocene climate changes in tropical South America is the huge rising of Titicaca lake level from 4400 to 4000 cal BP. Because the Amazon basin is the source of Andean rainfalls we have explored Amazonian data of climate changes during the Holocene to better understand the cause of this abrupt transition. Amazonian data confirm the existence of mid-Holocene dryness: (1) lacustrine level studies show a lower precipitation/evaporation budget than present, with the lowest lake levels between 8500 and 6800 cal BP; (2) although the dominant Holocene vegetation has always been the rainforest in the heart of Amazonia, this forest expanded towards the northwestern and southwestern regions from 6800 to 1550 cal BP, moreover, pioneer elements of the rainforest developed during the mid-Holocene and the best example is those of Cecropia, between 9000 and 5000 cal BP. (3) soil d13C indicates a forest expansion over savannas areas in Roraima (north), Mato Grosso and Rondonia (southwest), during the Holocene. (4) the mid-Holocene (8000- 4000 cal BP) is characterized by repeated occurrences of forest fires, marked by the presence of charcoals in soils and lacustrine sediments. However these different records are not characterized by abrupt transitions at the end of the Middle Holocene in Amazonia. In the Andean records there is a clear north-south shift in the timing of the transition. Analysis of coupled Ocean Atmosphere Model simulations suggest that convection in Amazon basin is directly controlled by insolation leading to an almost linear response of local climate to the global forcing. Differently, in the eastern and south-western regions where the rain is brought by the South American Monsoon, the climate transition appears more abrupt. It may be because the involved climate mechanisms are more complex and depend on Ocean/Atmosphere/Vegetation coupled process (ITCZ position, ZCAS formation, etc.). Tectonic movements or threshold links to

A numerical method for PCM-based pin fin heat sinks optimization

International Nuclear Information System (INIS)

Pakrouh, R.; Hosseini, M.J.; Ranjbar, A.A.; Bahrampoury, R.

2015-01-01

Highlights: • Optimization of PCM-based heat sink by using the Taguchi method. • Derivation of optimal PCM percentage to reach the maximum critical time. • Optimization is performed for four different critical temperatures. • Effective design factors are fins’ height and fins’ number. • The optimum configuration depends on geometric properties and the critical temperature. - Abstract: This paper presents a numerical investigation on geometric optimization of PCM-based pin fin heat sinks. Paraffin RT44HC is used as PCM while the fins and heat sink base is made of aluminum. The fins act as thermal conductivity enhancers (TCEs). The main goal of the study is to obtain the configurations that maximize the heat sink operational time. An approach witch couples Taguchi method with numerical simulations is utilized for this purpose. Number of fins, fins height, fins thickness and the base thickness are parameters which are studied for optimization. In this study natural convection and PCM volume variation during melting process are considered in the simulations. Optimization is performed for different critical temperatures of 50 °C, 60 °C, 70 °C and 80 °C. Results show that a complex relation exists between PCM and TCE volume percentages. The optimal case strongly depends on the fins’ number, fins’ height and thickness and also the critical temperature. The optimum PCM percentages are found to be 60.61% (corresponds to 100 pin fin heat sink with 4 mm thick fins) for critical temperature of 50 °C and 82.65% (corresponds to 100 pin fin heat sink with 2 mm thick fins) for other critical temperatures

La légalisation du cannabis au Canada: Les défis politiques

Directory of Open Access Journals (Sweden)

Line Beauchesne

Full Text Available Résumé Le gouvernement libéral du Canada élu majoritaire le 19 octobre 2015 avait dans ses promesses électorales la légalisation du cannabis. Il tiendra parole. Un Document de discussion fut publié en juin 2016 donnant les assises au Groupe de Travail sur la Légalisation et la Réglementation du Cannabis qui a rendu son rapport le 30 novembre 2016. Ce rapport, a expliqué le gouvernement, sera un des outils pour élaborer son cadre législatif et servira de base aux discussions avec les provinces et territoires, de même que les experts qui auront à gérer ce cadre réglementaire. Dans cet article, nous verrons les principaux défis politiques qui attendent le gouvernement dans ces discussions avec les provinces et territoires, de même que les experts, considérant les questions posées sur les cinq aspects de la réglementation dans le Document de discussion. Pour identifier ces défis, en plus des apprentissages retenus par les études sur la situation au Colorado et à Washington, se grefferont les apprentissages des études quant à la gestion actuelle des drogues légales. En premier lieu sont exposés les défis liés à l’arrivée même de cette loi, puis ceux qui touchent à l’objectif de santé publique, au système de production, de transformation et de distribution, au contrôle du cadre réglementaire, et enfin, à la question plus spécifique du cannabis à des fins thérapeutiques. Nous verrons pourquoi l’application de cette loi sera complexe, coûteuse et pourra aisément dévier des objectifs de départ. Une surveillance à court et à long terme sera nécessaire pour s’assurer que les différents niveaux de gouvernement conservent la primauté de la santé publique et considèrent l’usage du pénal en dernier recours.

Design, Implementation and Control of a Fish Robot with Undulating Fins

Directory of Open Access Journals (Sweden)

Mohsen Siahmansouri

2011-11-01

Full Text Available Biomimetic robots can potentially perform better than conventional robots in underwater vehicle designing. This paper describes the design of the propulsion system and depth control of a robotic fish. In this study, inspired by knife fish, we have designed and implemented an undulating fin to produce propulsive force. This undulating fin is a segmental anal fin that produces sinusoidal wave to propel the robot. The relationship between the individual fin segment and phase angles with the overall fin trajectory has also been discussed. This propulsive force can be adjusted and directed for fish robot manoeuvre by a mechanical system with two servomotors. These servomotors regulate the direction and depth of swimming. A wireless remote control system is designed to adjust the servomotors which enables us to control revolution, speed and phase differences of neighbor servomotors of fins. Finally, Field trials are conducted in an outdoor pool to demonstrate the relationship between robotic fish speed and fin parameters like phase difference, the number of phase and undulatory amplitude.

Holocene Lake-Level Fluctuations of Lake Aricota, Southern Peru

Science.gov (United States)

Placzek, Christa; Quade, Jay; Betancourt, Julio L.

2001-09-01

Lacustrine deposits exposed around Lake Aricota, Peru (17° 22‧S), a 7.5-km2 lake dammed by debris flows, provide a middle to late Holocene record of lake-level fluctuations. Chronological context for shoreline deposits was obtained from radiocarbon dating of vascular plant remains and other datable material with minimal 14C reservoir effects (<350 yr). Diatomites associated with highstands several meters above the modern lake level indicate wet episodes. Maximum Holocene lake level was attained before 6100 14C yr B.P. and ended ∼2700 14C yr B.P. Moderately high lake levels occurred at 1700 and 1300 14C yr B.P. The highstand at Lake Aricota during the middle Holocene is coeval with a major lowstand at Lake Titicaca (16°S), which is only 130 km to the northeast and shares a similar climatology. Comparisons with other marine and terrestrial records highlight emerging contradictions over the nature of mid-Holocene climate in the central Andes.

FinTech transformation: how it-enabled innovations shape the financial sector

OpenAIRE

Zavolokina, Liudmila; Dolata, Mateusz; Schwabe, Gerhard

2016-01-01

FinTech, the phenomenon which spans over the areas of information technologies and financial innovation, is currently on the rise and is gaining more and more attention from practitioners, investors and researchers. FinTech is broadly discussed by the media, which constitutes its understanding and represents social opinion, however, this perception of FinTech should be supported by empirical evidences. Therefore, we examine five Swiss FinTech companies through the lens of the conceptual frame...

Fish Pectoral Fin Hydrodynamics; Part III: Low Dimensional Models via POD Analysis

Science.gov (United States)

Bozkurttas, M.; Madden, P.

2005-11-01

The highly complex kinematics of the pectoral fin and the resulting hydrodynamics does not lend itself easily to analysis based on simple notions of pitching/heaving/paddling kinematics or lift/drag based propulsive mechanisms. A more inventive approach is needed to dissect the fin gait and gain insight into the hydrodynamic performance of the pectoral fin. The focus of the current work is on the hydrodynamics of the pectoral fin of a bluegill sunfish in steady forward motion. The 3D, time-dependent fin kinematics is obtained via a stereo-videographic technique. We employ proper orthogonal decomposition to extract the essential features of the fin gait and then use CFD to examine the hydrodynamics of simplified gaits synthesized from the POD modes. The POD spectrum shows that the first two, three and five POD modes capture 55%, 67%, and 80% of the motion respectively. The first three modes are in particular highly distinct: Mode-1 is a ``cupping'' motion where the fin cups forward as it is abducted; Mode-2 is an ``expansion'' motion where the fin expands to present a larger area during adduction and finally Mode-3 involves a ``spanwise flick'' of the dorsal edge of the fin. Numerical simulation of flow past fin gaits synthesized from these modes lead to insights into the mechanisms of thrust production; these are discussed in detail.

¿Hacia el fin de la itinerancia? Isabel I de Castilla

Directory of Open Access Journals (Sweden)

Mª Isabel DEL VAL VALDIVIESO

2009-05-01

Full Text Available Aunque ciertos organismos de la administración del reino están ya asentados en determinados lugares, y se observan algunos indicios de sedentarización, entre ellos el establecimiento de la casa del príncipe Juan en Almazán, la corte de Isabel la Católica sigue siendo itinerante como la de sus antecesores. Con el fin de constatar esta circunstancia, en el presente artículo se estudia el trayecto seguido por Isabel I de Castilla en dos ocasiones, el primer año de reinado, y el último viaje que realiza. En 1475 el espacio recorrido se extiende entre Palencia y Toledo, se trata de un periplo con ida (hacia el Sur y regreso al norte del Duero. En 1503, el viaje se desarrolla entre Alcalá de Henares y Medina del Campo, villa en la que morirá la reina Católica el 26 de noviembre de 1504. En ambas ocasiones, la reina atiende todos los asuntos del gobierno de sus reinos allí donde se encuentre.Malgré l’installation de certains organes de l’administration du royaume dans des lieux précis et quelques indices de sédentarisation, comme l’établissement de la maison du Prince Juan à Almazán, la cour d’Isabelle la Catholique est, comme celle de ses prédécesseurs, itinérante. Cet article se propose d’étudier deux trajets parcourus par Isabelle Ire de Castille : celui qu’elle réalise au cours de la première année de son règne, et le dernier. En 1475, l’espace parcouru s’étend de Palencia à Tolède ; il s’agit d’un trajet vers le sud pour l’aller et au nord du Duero pour le retour. En 1503, le voyage se déroule entre Alcalá de Henares et Medina del Campo, où la reine meurt le 26 novembre 1504. Lors de ces deux déplacements, la reine administre son royaume de l’endroit où elle se trouve.

Thermohydraulic analysis of smooth and finned annular ducts

International Nuclear Information System (INIS)

Braga, C.V.M.

1987-01-01

The present work is concerned with the turbulent heat transfer and pressure drop in smooth and finned annular ducts overage heat transfer coefficients have been obtained by means of the heat exchanger theory. In addition, friction factors have also been determined. The experiments were performed by utilizing four double-pipe heat exchangers. The flowing fluids, in the heat exchangers, were air and water. The average heat transfer coefficients, for air flowing in the annular section, were determined by measuring the overall heat transfer coefficients of the heat exchangers. In order to attain fully developed conditions, the heat exchangers had a starting length of 30 hydraulic diameters. The thermal boundary conditions consisted of uniform temperature on the inner surface, the outer surface being insulated. The heat transfer coefficients and friction factors are presented in dimensionaless forms, as functions of the Reynolds number of the flow. The results for the smooth and finned annular ducts were compared. The purpose of such comparison was to study the influence of the fins on the pressure drop and heat transfer rate. In the case of the finned nular ducts, it is shown that the fin efficiency has some fluence on the heat transfer rates. The, a two-dimensional at transfer analysis was performed in order to obtain the n efficiency and the annular region efficiency. It is also shown that the overall thermal performance of finned surfaces epends mainly on the Nusselt number and on the region eficiency. These parameters are presented as functions of the Reynolds number of the flow and the geometry of the problem. (author) [pt

Heat transfer and pressure drop characteristics of mini-fin structures

International Nuclear Information System (INIS)

Jiang Peixue; Xu Ruina

2007-01-01

Forced convection heat transfer of air and water in bronze and pure copper mini-fin structures and mini-channel structures was investigated experimentally. The mini-fin dimensions were 0.7 mm x 0.2 mm and 0.8 mm x 0.4 mm. The tests included both staggered diamond-shaped and in-line square mini-fin arrangements. The tests investigated the effects of structures, mini-fin dimensions and arrangement, test section materials, and fluid properties on the convection heat transfer and heat transfer enhancement. For the tested conditions, the convection heat transfer coefficient was increased 9-21 fold for water and 12-38 fold for air in the mini-fin structures compared with an empty plate channel. The friction factor and flow resistance in the mini-channel structures and the in-line square mini-fin arrangement were much less than in the staggered diamond-shaped mini-fin arrangement. For the small channel width, W c = 0.2 mm, the convection heat transfer with the in-line square array structure was more intense than with the staggered diamond-shaped structure, the mini-channel structure or the porous media. For the larger channel width, W c = 0.4 mm, the convection heat transfer in the staggered diamond-shaped array structure was more intense than in the others systems while the in-line square structure had the best overall thermal-hydraulic performance

Le ministre du Commerce international du Canada rencontre des ...

International Development Research Centre (IDRC) Digital Library (Canada)

17 juil. 2017 ... La promotion de l'entrepreneuriat, la façon dont le commerce peut profiter aux femmes et à leur famille, et la création d'emplois pour les plus vulnérables étaient au coeur de la discussion en table ronde du ministre du Commerce international du Canada, l'honorable François-Philippe Champagne, et des ...

Le chaos et l'harmonie la fabrication du Réel

CERN Document Server

Xuan Thuan, Trinh

1998-01-01

Cette fin de siècle a vu un véritable bouleversement dans notre façon de concevoir le monde. Après avoir dominé la pensée occidentale pendant trois cents ans, la vision newtonienne d'un univers fragmenté, mécaniste et déterministe a fait place à celle d'un monde exubérant de créativité. Le Réel n'est plus déterminé seulement par des lois naturelles appliquées à des conditions initiales particulières, mais aussi moulé et façonné par une suite d'événements contingents et historiques qui peuvent bouleverser la réalité à son niveau le plus profond. Celui du bolide rocailleux venu percuter la Terre il y a quelque 65 millions d'années et responsable de la mort des dinosaures en est un exemple. Les lois physiques ont perdu leur rigidité. Avec l'avènement de la mécanique quantique, le hasard est entré en force dans le monde subatomique. Le monde macroscopique n'a pas été épargné. Avec la théorie du chaos, le hasard et le non-déterminisme ont envahi non seulement la vie de tous le...

A Numerical Study of Natural Convection Heat Transfer in Fin Ribbed Radiator

Directory of Open Access Journals (Sweden)

Hua-Shu Dou

2015-01-01

Full Text Available This paper numerically investigates the thermal flow and heat transfer by natural convection in a cavity fixed with a fin array. The computational domain consists of both solid (copper and fluid (air areas. The finite volume method and the SIMPLE scheme are used to simulate the steady flow in the domain. Based on the numerical results, the energy gradient function K of the energy gradient theory is calculated. It is observed from contours of the temperature and energy gradient function that the position where thermal instability takes place correlates well with the region of large K values, which demonstrates that the energy gradient method reveals the physical mechanism of the flow instability. Furthermore, the effects of the fin height, the fin number, and the fin shape on the heat transfer rate are also investigated. It is found that the thermal performance of the fin array is determined by the combined effect of the fin space and fin height. It is also observed that the effect of fin shape on heat transfer is insignificant.

Application of homotopy analysis method and inverse solution of a rectangular wet fin

International Nuclear Information System (INIS)

Panda, Srikumar; Bhowmik, Arka; Das, Ranjan; Repaka, Ramjee; Martha, Subash C.

2014-01-01

Highlights: • Solution of a wet fin with is obtained by homotopy analysis method (HAM). • Present HAM results have been well-validated with literature results. • Inverse analysis is done using genetic algorithm. • Measurement error of ±10–12% (approx.) is found to yield satisfactory reconstructions. - Abstract: This paper presents the analytical solution of a rectangular fin under the simultaneous heat and mass transfer across the fin surface and the fin tip, and estimates the unknown thermal and geometrical configurations of the fin using inverse heat transfer analysis. The local temperature field is obtained by using homotopy analysis method for insulated and convective fin tip boundary conditions. Using genetic algorithm, the thermal and geometrical parameters, viz., thermal conductivity of the material, surface heat transfer coefficient and dimensions of the fin have been simultaneously estimated for the prescribed temperature field. Earlier inverse studies on wet fin have been restricted to the analysis of nonlinear governing equation with either insulated tip condition or finite tip temperature only. The present study developed a closed-form solution with the consideration of nonlinearity effects in both governing equation and boundary condition. The study on inverse optimization leads to many feasible combination of fin materials, thermal conditions and fin dimensions. Thus allows the flexibility for designing a fin under wet conditions, based on multiple combinations of fin materials, fin dimensions and thermal configurations to achieve the required heat transfer duty. It is further determined that the allowable measurement error should be limited to ±10–12% in order to achieve satisfactory reconstruction

Les bases de données pédagogiques sur Internet : le cas du programme Éducasup

Directory of Open Access Journals (Sweden)

Christine Develotte

2005-11-01

Full Text Available Ces dix dernières années, l'émergence de l'information en ligne a suscité des appels d'offres nationaux visant à la mise en place de bases de données. Nous revenons ici sur l'histoire du programme Éducasup, de sa conception en 1997 à son abandon, fin 2003. À travers une analyse sémio-linguistique des écrans d'accueil de ses différentes chartes graphiques, nous cherchons à montrer les choix politiques et techniques qui ont présidé à l'évolution de ce programme.

Dry/wet performance of a plate-fin air-cooled heat exchanger with continuous corrugated fins

International Nuclear Information System (INIS)

Hauser, S.G.; Kreid, D.K.; Johnson, B.M.

1981-01-01

The performance and operating characteristics of a plate-fin heat exchanger in dry/wet or deluge operations was experimentally determined. Development of the deluge heat/mass transfer model continued. The experiments were conducted in a specially-designed wind tunnel at the PNL. Air that was first heated and humidified to specified conditions was circulated at a controlled rate through a 2 ft x 6 ft heat exchanger module. The heat exchanger used in the tests was a wavy surface, plate fin on tube configuration. Hot water was circulated through the tubes at high flow rates to maintain an essentially isothermal condition on the tube side. Deionized water sprayed on the top of the vertically oriented plate fins was collected at the bottom of the core and recirculated. Instrumentation was provided for measurement of flow rates and thermodynamic conditions in the air, in the core circulation water, and in the deluge water. Measurements of the air side pressure drop and heat rejection rate were made as a function of air flow rate, air inlet temperature and humidity, deluge water flow rate, and the core inclination from the vertical. An overall heat transfer coefficient and an effective deluge film convective coefficient was determined. The deluge model, for predicting heat transfer from a wet finned heat exchanger was further developed and refined, and a major extension of the model was formulated that permits simultaneous calculation of both the heat transfer and evaporation rates from the wetted surface. The experiments showed an increase in the heat rejection rate due to wetting, accompanied by a proportional increase in the air side pressure drop. For operation at the same air side pressure drop, the enhancement ratio Q/sub w//Q/sub d/ varied between 2 and 5 for the conditions tested. Thus, the potential enhancement of heat transfer due to wetting can be substantial

Heat transfer from rotating finned heat exchangers with different orientation angles

Energy Technology Data Exchange (ETDEWEB)

Tawfik, Adel Abdalla [Suez Canal University, Marine Engineering and Naval Architecture Department, Faculty of Engineering, Port Said (Egypt)

2010-03-15

The local and average heat transfer characteristics of spoke like fins that extend outward from a rotating shaft have been determined experimentally. The experiments encompassed a number of geometrical parameters, including the length and chord of the fins, the number of fins deployed around the circumference of the shaft and the orientation angles of the fin. The experiments cover a wider range of rotational speeds, which varies from 25 up to 2,000 rpm. Three wire heat flux sensors have been used in conjunction with a slip ring apparatus to evaluate the local and average heat transfer coefficients. The output results indicated that, the heat transfer transition on rotating fins occurs at Reynolds number lower than encountered on the stationary rectangular fins in crossflow. In general, with non zero incidence angle, the rotating system acts as a fan and creates axial air motion, which enhance the heat transfer rate. However, the effect of orientation angle reduces with increasing the rotational speed. The Nusselt number data are independent of the number of fins in the circumferential array at high rotational speed and are weakly dependent at low Reynolds numbers. To facilitate the use of the results for design, correlations were developed which represent the fin heat transfer coefficient as a continuous function of the investigated independent parameters. (orig.)

Heat transfer and pressure drop characteristics of the tube bank fin heat exchanger with fin punched with flow redistributors and curved triangular vortex generators

Science.gov (United States)

Liu, Song; Jin, Hua; Song, KeWei; Wang, LiangChen; Wu, Xiang; Wang, LiangBi

2017-10-01

The heat transfer performance of the tube bank fin heat exchanger is limited by the air-side thermal resistance. Thus, enhancing the air-side heat transfer is an effective method to improve the performance of the heat exchanger. A new fin pattern with flow redistributors and curved triangular vortex generators is experimentally studied in this paper. The effects of the flow redistributors located in front of the tube stagnation point and the curved vortex generators located around the tube on the characteristics of heat transfer and pressure drop are discussed in detail. A performance comparison is also carried out between the fins with and without flow redistributors. The experimental results show that the flow redistributors stamped out from the fin in front of the tube stagnation points can decrease the friction factor at the cost of decreasing the heat transfer performance. Whether the combination of the flow redistributors and the curved vortex generators will present a better heat transfer performance depends on the size of the curved vortex generators. As for the studied two sizes of vortex generators, the heat transfer performance is promoted by the flow redistributors for the fin with larger size of vortex generators and the performance is suppressed by the flow redistributors for the fin with smaller vortex generators.

Control characteristics for wrap-around fins on cruise missiles configurations

Science.gov (United States)

Sawyer, W. C.; Monta, W. J.; Carter, W. V.; Alexander, W. K.

1981-01-01

This paper presents selected results of a panel loads study conducted as part of the final phase of an extensive investigation of an air-breathing missile concept employing wrap-around aerodynamic surfaces. Typical results for M = 2.36 are presented for the fin load results, plus a brief review of basic results of the previously reported tests. Vapor screen results are also discussed. The present results indicate that the fin load characteristics are nearly identical for planar and curved fins having the same projected planform and would permit the use of planar-surface predictions for supersonic speeds in the preliminary design stages of missiles employing wrap-around curved fins.

Thermal analysis of annular fins with temperature-dependent thermal properties

Institute of Scientific and Technical Information of China (English)

I. G. AKSOY

2013-01-01

The thermal analysis of the annular rectangular profile fins with variable thermal properties is investigated by using the homotopy analysis method (HAM). The thermal conductivity and heat transfer coefficient are assumed to vary with a linear and power-law function of temperature, respectively. The effects of the thermal-geometric fin parameter and the thermal conductivity parameter variations on the temperature distribution and fin efficiency are investigated for different heat transfer modes. Results from the HAM are compared with numerical results of the finite difference method (FDM). It can be seen that the variation of dimensionless parameters has a significant effect on the temperature distribution and fin efficiency.

Characteristics of a micro-fin evaporator: Theoretical analysis and experimental verification

Directory of Open Access Journals (Sweden)

Zheng Hui-Fan

2013-01-01

Full Text Available A theoretical analysis and experimental verification on the characteristics of a micro-fin evaporator using R290 and R717 as refrigerants were carried out. The heat capacity and heat transfer coefficient of the micro-fin evaporator were investigated under different water mass flow rate, different refrigerant mass flow rate, and different inner tube diameter of micro-fin evaporator. The simulation results of the heat transfer coefficient are fairly in good agreement with the experimental data. The results show that heat capacity and the heat transfer coefficient of the micro-fin evaporator increase with increasing logarithmic mean temperature difference, the water mass flow rate and the refrigerant mass flow rate. Heat capacity of the micro-fin evaporator for diameter 9.52 mm is higher than that of diameter 7.00 mm with using R290 as refrigerant. Heat capacity of the micro-fin evaporator with using R717 as refrigerant is higher than that of R290 as refrigerant. The results of this study can provide useful guidelines for optimal design and operation of micro-fin evaporator in its present or future applications.

Pectoral fin contact as a mechanism for social bonding among dolphins

Science.gov (United States)

Dudzinski, Kathleen; Ribic, Christine

2017-01-01

Bottlenose dolphins are large-brained social mammals residing in a fission-fusion society with relationships that are established and maintained over decades. We examined a decade-long data set of inter-individual pectoral fin contact exchanges to better understand how dolphins share information via tactile contact. Sex and age are significant factors in pectoral fin contact within non-kin dolphin dyads. Adult females shared more pectoral fin contacts with other adult females, while younger females showed no pattern of contact. Males shared more pectoral fin contacts with other males as juveniles and as adults, but showed no difference in the number of touches versus rubs as pectoral fin contacts with other males. Whether in the role of initiator as rubber or initiator as rubbee, male dolphins again preferred other males. These results support the notion that dolphins, especially male dolphins, might use pectoral fin contact as one tool in their repertoire for social bonding to establish, maintain and manage their inter-individual relationships. Additionally, it is also likely that the exchange of pectoral fin contact is developed and refined as individuals age, mature socially, and establish their place within a fission-fusion society.

Comparaison du filtre adaptatif RIF et du filtre a base de reseau de ...

African Journals Online (AJOL)

Comparaison du filtre adaptatif RIF et du filtre a base de reseau de neurones pour le filtrage du courant de reference pour la commande du filtre actif parallele. C Benachaiba, A Bassou, B Mazari ...

Contrasting evidence of Holocene ice margin retreat, south-western Greenland

DEFF Research Database (Denmark)

Levy, L. B.; Larsen, N. K.; Davidson, T. A.

2017-01-01

Constraining the Greenland Ice Sheet's (GrIS) response to Holocene climate change provides calibrations for ice sheet models that hindcast past ice margin fluctuations. Ice sheet models predict enhanced ice retreat in south-western Greenland during the middle Holocene; however, few geological...... observations corroborating the extensive retreat are available. We present new data from lake sediment cores from the Isua region, south-western Greenland, which provide constraints on Holocene fluctuations of the GrIS margins. Our data indicate that the main GrIS margin was 30 km west of its present...

Enhancement of heat transfer. The performance of micro-fin tubes

International Nuclear Information System (INIS)

Muzzio, A.

2001-01-01

Micro-fin tubes are characterised by numerous, very small integral fins that spiral down the inner surface. A very interesting feature of their performance in flow boiling and condensation is a large heat transfer enhancement accompanied by a low pressure drop penalty. This paper presents a general overview of micro-fin tubes and of their performance in evaporation, condensation and single-phase flow [it

A persistent Holocene wetting trend in arid central Asia, with wettest conditions in the late Holocene, revealed by multi-proxy analyses of loess-paleosol sequences in Xinjiang, China

Science.gov (United States)

Chen, Fahu; Jia, Jia; Chen, Jianhui; Li, Guoqiang; Zhang, Xiaojian; Xie, Haichao; Xia, Dunsheng; Huang, Wei; An, Chengbang

2016-08-01

There are significant differences in the interpretation of the moisture (precipitation) history of arid central Asia (ACA) during the Holocene, as inferred on one hand from speleothem oxygen isotope records, and on the other from lake sediments. Here we present the results of measurements of climatically-sensitive magnetic properties and soil color from four well-dated loess-paleosol sequences from the northern slopes of the Tienshan Mountains and the Yili River valley, Xinjiang, China, in the core area of ACA. Our results demonstrate that the characteristic Holocene paleosol, indicating relatively moist conditions, generally formed after ∼6 ka (1 ka = 1000 cal yr BP) in the study region, and that the accumulation of unweathered loess prevailed during the early Holocene, indicating a dry climate at that time. The magnetic proxies further reveal a trend of generally increasing moisture since the Last Glacial Maximum, with the wettest climate occurring during the late Holocene. This trend of increasing moisture during the Holocene is representative of the Xinjiang region and possibly of the whole of the core area of ACA, and is in marked contrast both to the mid-Holocene moisture maximum observed in the East Asian summer monsoon region and to the general decrease in the strength of the Indian summer monsoon since the early Holocene. Our findings are supported by the results of a climate simulation which indicate a trend of increasing summer and winter precipitation during the Holocene in the core area of ACA, caused mainly by an increase in the strength of the westerlies effected by an increasing latitudinal insolation gradient and by a negative trend of the Arctic Oscillation (AO) or North Atlantic Oscillation (NAO).

Mechanism of tonal noise generation from circular cylinder with spiral fin

Science.gov (United States)

Yamashita, Ryo; Hayashi, Hidechito; Okumura, Tetsuya; Hamakawa, Hiromitsu

2014-12-01

The pitch of the spiral finned tube influences seriously to the acoustic resonance in the heat exchanger. In this research, the flow characteristics in relating to the aeolian tone from the finned cylinder are studied by the numerical simulation. It is observed that the tonal noise generated from the finned tube at two pitch spaces. The ratio of the fin pitch to the cylinder diameter is changed at 0.11 and 0.27. The tone level increases and the frequency decreases with the pitch shorter. The separation flow from the cylinder generates the span-wise vortices, Karman vortices, and the separation flow from the fin generates the stream-wise vortices. When the fin pitch ratio is small, the stream-wise vortices line up to span-wise and become weak rapidly. Only the Karman vortices are remained and integrate in span. So the Karman vortex became large. This causes the low frequency and the large aeolian tone.

Fgf16 is essential for pectoral fin bud formation in zebrafish

International Nuclear Information System (INIS)

Nomura, Ryohei; Kamei, Eriko; Hotta, Yuuhei; Konishi, Morichika; Miyake, Ayumi; Itoh, Nobuyuki

2006-01-01

Zebrafish pectoral fin bud formation is an excellent model for studying morphogenesis. Fibroblast growth factors (Fgfs) and sonic hedgehog (shh) are essential for pectoral fin bud formation. We found that Fgf16 was expressed in the apical ectodermal ridge (AER) of fin buds. A knockdown of Fgf16 function resulted in no fin bud outgrowth. Fgf16 is required for cell proliferation and differentiation in the mesenchyme and the AER of the fin buds, respectively. Fgf16 functions downstream of Fgf10, a mesenchymal factor, signaling to induce the expression of Fgf4 and Fgf8 in the AER. Fgf16 in the AER and shh in the zone of polarizing activity (ZPA) interact to induce and/or maintain each other's expression. These findings have revealed that Fgf16, a newly identified AER factor, plays a crucial role in pectoral fin bud outgrowth by mediating the interactions of AER-mesenchyme and AER-ZPA

Etat Du Magnesium Dans Quelques Sols Sales Du Sud Et Du ...

African Journals Online (AJOL)

étude a été réalisée sur 86 échantillons de sols provenant du Centre et du Sud de l´Irak. L\\'expérimentation a consisté, d´une part, à calculer les différents sels dominants dans les sols salés par la méthode de combinaison hypothétique et, ...

Ontogenetic scaling of caudal fin shape in Squalus acanthias (Chondrichthyes, Elasmobranchii): a geometric morphometric analysis with implications for caudal fin functional morphology.

Science.gov (United States)

Reiss, Katie L; Bonnan, Matthew F

2010-07-01

The shark heterocercal caudal fin and its contribution to locomotion are of interest to biologists and paleontologists. Current hydrodynamic data show that the stiff dorsal lobe leads the ventral lobe, both lobes of the tail are synchronized during propulsion, and tail shape reflects its overall locomotor function. Given the difficulties surrounding the analysis of shark caudal fins in vivo, little is known about changes in tail shape related to ontogeny and sex in sharks. A quantifiable analysis of caudal fin shape may provide an acceptable proxy for inferring gross functional morphology where direct testing is difficult or impossible. We examined ontogenetic and sex-related shape changes in the caudal fins of 115 Squalus acanthias museum specimens, to test the hypothesis that significant shape changes in the caudal fin shape occur with increasing size and between the sexes. Using linear and geometric morphometrics, we examined caudal shape changes within the context of current hydrodynamic models. We found no statistically significant linear or shape difference between sexes, and near-isometric scaling trends for caudal dimensions. These results suggest that lift and thrust increase linearly with size and caudal span. Thin-plate splines results showed a significant allometric shape change associated with size and caudal span: the dorsal lobe elongates and narrows, whereas the ventral lobe broadens and expands ventrally. Our data suggest a combination of caudal fin morphology with other body morphology aspects, would refine, and better elucidate the hydrodynamic factors (if any) that underlie the significant shape changes we report here for S. acanthias.

High temperature mechanical properties on multi stage blazed fin body with ultra fine off-set fin for compact heat exchanger

International Nuclear Information System (INIS)

Ishiyama, Shintaro; Muto, Yasushi

2003-01-01

Three stage blazed plate fin body with ultra fine off-set fin (thickness x height x pitch x off-set pitch = 0.22 mm x 1.2 mm x 1.6 mm x 5 mm) for 600 MWt High Temperature Gas Cooled Reactor Gas Turbin (HTGR-GT) system was fabricated and tested on its high temperature mechanical properties and the following results were derived. (1) tested body shows almost the same strength an fatigue behavior of SUS 304 as main structural material at elevated temperatures up to 873 K, (2) static and fatigue fracture mainly occurred at ultra fine off-set and (3) high temperature strength and fatigue life are improved by blazing technique to double side walls of the fin by Ni blaze material. (author)

Flow-structure Interaction Modeling of a Fish Caudal Fin during Steady Swimming

Science.gov (United States)

Liu, Geng; Geng, Biao; Zheng, Xudong; Xue, Qian; Dong, Haibo

2017-11-01

It's widely thought that the flexibilities of fish fins play critical roles in propulsive performance enhancement (such as thrust augment and efficiency improvement) in nature. In order to explore the formation mechanisms of the fish fin's flexible morphing and its hydrodynamic benefits as well, a high-fidelity flow-structure/membrane interaction modeling of the fish caudal fin is conducted in this work. Following the realistic configuration of the fish caudal fin, a thin membrane supported by a series of beams is constructed. The material properties of the membrane and the beams are reversely determined by the realistic fin morphing obtained from the high-speed videos and the high fidelity flow-structure interaction simulations. With the accurate material property, we investigate the interplay between structure, kinematics and fluid flow in caudal fin propulsion. Detailed analyses on the relationship between the flexural stiffness, fin morphing patterns, hydrodynamic forces and vortex dynamics are then conducted.

Effects of fin shape on condensation in herringbone microfin tubes

Energy Technology Data Exchange (ETDEWEB)

Miyara, Akio [Saga University (Japan). Dept. of Mechanical Engineering; Otsubo, Yusuke; Ohtsuka, Satoshi; Mizuta, Yoshihiko [Saga University (Japan). Graduate School of Science and Engineering

2003-06-01

Effects of fin height and helix angle on condensation inside a herringbone microfin tube have been experimentally investigated with five types of herringbone microfin tubes. Heat transfer coefficients are about 2-4 times higher than that of the helical microfin tube under high mass velocity conditions. In the low mass velocity, they are equal to that of the helical microfin tube. The heat transfer enhancement increases with fin height up to 0.18 mm; higher fin heights show enhancement values similar to the 0.18 mm results. Pressure drop increases with the fin height. Larger helix angle yields higher heat transfer and higher pressure drop. For the lowest fin and/or smallest helix angle, the pressure drop is comparable with that of the helical microfin tube, while the heat transfer enhancement is higher. The enhancement mechanism is discussed from flow pattern observations. Effect of mass transfer resistance for R410A is estimated and negligible effects have been proved. (author)

Development of a Simulation Model for Swimming with Diving Fins

Directory of Open Access Journals (Sweden)

Motomu Nakashima

2018-02-01

Full Text Available The simulation model to assess the performance of diving fin was developed by extending the swimming human simulation model SWUM. A diving fin was modeled as a series of five rigid plates and connected to the human model by springs and dampers. These plates were connected to each other by virtual springs and dampers, and fin’s bending property was represented by springs and dampers as well. An actual diver’s swimming motion with fins was acquired by a motion capture experiment. In order to determine the bending property of the fin, two bending tests on land were conducted. In addition, an experiment was conducted in order to determine the fluid force coefficients in the fluid force model for the fin. Finally, using all measured and identified information, a simulation, in which the experimental situation was reproduced, was carried out. It was confirmed that the diver in the simulation propelled forward in the water successfully.

“Gloire immortelle de nos Aïeux” les armes des ancetres dans les agglomerations du sudouest europeen a la fin de l'age du Fer: les exemples de Raso de Candeleda et le Cayla de Mailhac

Directory of Open Access Journals (Sweden)

Bertaud, Alexandre

2015-12-01

Full Text Available To understand the social interaction in warfare context, and specially claim of warrior ancestors, in this paper, we are going to study remains of anachronistic weapons in two late prehistorical agglomerations in South-Western Europe: Candeleda (Spain, Ávila and Mailhac (France, Aude. Study of discovery contexts is the main point to understand the place took by weaponry in these societies. So we are going to approach the claim of warlordism by the highlighting of ancestors warlords through their weapons.Para entender las relaciones sociales en la esfera guerrera, y particularmente la reclamación de una ascendencia de señor de guerra, en este articulo, vamos a analizar restos de armas anacrónicas en dos aglomeraciones de la final de la Edad del Hierro en Europa suroeste : Candeleda (Ávila, España y Mailhac (Aude, Francia. El estudio de los contextos de descubrimiento es un factor crucial en la comprensión de la posición de armas en estas sociedades. Así, vamos a considerar la reclamación de una élite guerrera por el desarrollo de ascendientes señores de la guerra, a través de sus armas. [fr] Afin d’appréhender les rapports sociaux inhérents à la sphère guerrière, et particulièrement la revendication d’une ascendance de chef de guerre, nous allons, dans cet article, analyser les restes d’armes anachroniques dans deux agglomérations de la fin de l’âge du Fer dans le sud-ouest européen : Candeleda et Mailhac. L’étude des contextes de découvertes est alors primordiale dans la compréhension de la place de l’armement dans ces sociétés. Nous allons ainsi pouvoir approcher la revendication d’une élite guerrière par la mise en valeur des ancêtres chefs de guerre à travers leurs armes.

Le patrimoine rural en Languedoc-Roussillon : acquis et perspectives du travail d’inventaire

Directory of Open Access Journals (Sweden)

Marie-Sylvie Grandjouan

2012-04-01

Full Text Available Vingt cantons ruraux ont été traités par l’équipe de l’Inventaire en Languedoc-Roussillon. Les exemples présentés ici illustrent la variété des territoires de la région : mas de la plaine littorale avant et après l’expansion de la viticulture à fin du XIXe siècle ; maisons et villages de la vallée de l’Hérault ; fermes groupées en hameaux ou villages de la moyenne montagne qui couvre le nord du département de l’Hérault et la totalité du département de la Lozère où se dressent encore des édicules (fours à pain, travail à ferrer…, propriétés des communautés d’habitants ; habitat caussenard du Larzac méridional et du Sauveterre lié à la pratique de l’élevage ovin ; fermes bâties en terrasses dans la partie orientale des Cévennes ; enfin l’exemple de la Margeride tout au nord de la région.Twenty rural districts have been surveyed by the research workers of the Languedoc-Roussillon Inventaire. Examples shown here illustrate the wide range of territories, from the « mas » in the coastal plain, built before and after the wine-growing expansion era at the end of the 19th century, to the houses and villages in the Hérault valley. In the lower mountains covering the north of the Hérault and Lozère departments, the farms are concentrated in villages or hamlets where facilities shared by the inhabitants (bread-ovens, horse-shoeing devices… can still be seen. Distinct also are the dwellings in the Causses, south of Larzac and Sauveterre, connected with sheepfarming, farms built in terraces in the Eastern Cevennes and the Margeride, in the northern boundaries of the region.

Water flow and fin shape polymorphism in coral reef fishes.

Science.gov (United States)

Binning, Sandra A; Roche, Dominique G

2015-03-01

Water flow gradients have been linked to phenotypic differences and swimming performance across a variety of fish assemblages. However, the extent to which water motion shapes patterns of phenotypic divergence within species remains unknown. We tested the generality of the functional relationship between swimming morphology and water flow by exploring the extent of fin and body shape polymorphism in 12 widespread species from three families (Acanthuridae, Labridae, Pomacentridae) of pectoral-fin swimming (labriform) fishes living across localized wave exposure gradients. The pectoral fin shape of Labridae and Acanthuridae species was strongly related to wave exposure: individuals with more tapered, higher aspect ratio (AR) fins were found on windward reef crests, whereas individuals with rounder, lower AR fins were found on leeward, sheltered reefs. Three of seven Pomacentridae species showed similar trends, and pectoral fin shape was also strongly related to wave exposure in pomacentrids when fin aspect ratios of three species were compared across flow habitats at very small spatial scales (fish body fineless ratio across habitats or depths. Contrary to our predictions, there was no pattern relating species' abundances to polymorphism across habitats (i.e., abundance was not higher at sites where morphology is better adapted to the environment). This suggests that there are behavioral and/or physiological mechanisms enabling some species to persist across flow habitats in the absence of morphological differences. We suggest that functional relationships between swimming morphology and water flow not only structure species assemblages, but are yet another important variable contributing to phenotypic differences within species. The close links between fin shape polymorphism and local water flow conditions appear to be important for understanding species' distributions as well as patterns of diversification across environmental gradients.

Hydrodynamic function of dorsal fins in spiny dogfish and bamboo sharks during steady swimming.

Science.gov (United States)

Maia, Anabela; Lauder, George V; Wilga, Cheryl D

2017-11-01

A key feature of fish functional design is the presence of multiple fins that allow thrust vectoring and redirection of fluid momentum to contribute to both steady swimming and maneuvering. A number of previous studies have analyzed the function of dorsal fins in teleost fishes in this context, but the hydrodynamic function of dorsal fins in freely swimming sharks has not been analyzed, despite the potential for differential functional roles between the anterior and posterior dorsal fins. Previous anatomical research has suggested a primarily stabilizing role for shark dorsal fins. We evaluated the generality of this hypothesis by using time-resolved particle image velocimetry to record water flow patterns in the wake of both the anterior and posterior dorsal fins in two species of freely swimming sharks: bamboo sharks ( Chiloscyllium plagiosum ) and spiny dogfish ( Squalus acanthias ). Cross-correlation analysis of consecutive images was used to calculate stroke-averaged mean longitudinal and lateral velocity components, and vorticity. In spiny dogfish, we observed a velocity deficit in the wake of the first dorsal fin and flow acceleration behind the second dorsal fin, indicating that the first dorsal fin experiences net drag while the second dorsal fin can aid in propulsion. In contrast, the wake of both dorsal fins in bamboo sharks displayed increased net flow velocity in the majority of trials, reflecting a thrust contribution to steady swimming. In bamboo sharks, fluid flow in the wake of the second dorsal fin had higher absolute average velocity than that for first dorsal fin, and this may result from a positive vortex interaction between the first and second dorsal fins. These data suggest that the first dorsal fin in spiny dogfish has primarily a stabilizing function, while the second dorsal fin has a propulsive function. In bamboo sharks, both dorsal fins can contribute thrust and should be considered as propulsive adjuncts to the body during steady

En Defensa del Fin de Lucro en Salud.

Directory of Open Access Journals (Sweden)

Ramón Abel Castaño Yepes

2007-06-01

La quinta premisa se deriva de la cuarta y de la segunda, es decir, que si el diseño del sistema de salud introducido por la Ley 100 tiene como elemento distintivo el fin de lucro, entonces el resultado de dicho diseño tiene que ser indeseable, puesto que el fin de lucro es indeseable...

Effects of the partially movable control fin with end plate of underwater vehicle

Directory of Open Access Journals (Sweden)

Chul-Min Jung

2017-01-01

Full Text Available Underwater torpedo has control fin with very low aspect ratio due to launching from limited size of cylindrical torpedo tube. If the aspect ratio of control fin of underwater vehicle is very low three-dimensional flow around control fin largely reduces control forces. In this study, the end plate was applied to reduce the three-dimensional flow effects of partially movable control fin of underwater vehicle. Through numerical simulations the flow field around control fin was examined with and without end plate for different flap angles. The pressure, vorticity, lift and torque on the control fin were analyzed and compared to experiments. The comparison have shown a reasonable agreement between numerical and experimental results and the effect of end plate on a low aspect ratio control fin. When the end plate was attached to the movable control fin, the lift increased and the actuator shaft torque did not significantly change. As this means less consumption of the actuator shaft torque compared to the control fin that has the same control force, the inner actuator capacity can be reduced and energy consumption can be saved. Considering this, it is expected to be effectively applied to the control fin design of underwater vehicles such as torpedoes.

La légitimation du rock en URSS dans les années 1970-1980

OpenAIRE

Zaytseva, Anna

2017-01-01

RésuméL'article analyse le chemin parcouru par le rock en URSS puis en Russie, de l'état d'une (sous)culture occidentalisée anglophone, ayant trouvé refuge dans les discothèques des années 1960-1970, jusqu'au canon du russkij rok actuel, devenu presque synonyme de poésie chantée, via sa légitimation progressive dans les années 1980. Celle-ci a été amorcée à la fin des années 1970 avec l’arrivée en force d'une nouvelle génération artistique au sein de l'underground rock (« nouvelle vague » de ...

An experimental investigation into the deployment of 3-D, finned wing and shape memory alloy vortex generators in a forced air convection heat pipe fin stack

International Nuclear Information System (INIS)

Aris, M.S.; McGlen, R.; Owen, I.; Sutcliffe, C.J.

2011-01-01

Forced air convection heat pipe cooling systems play an essential role in the thermal management of electronic and power electronic devices such as microprocessors and IGBT's (Integrated Gate Bipolar Transistors). With increasing heat dissipation from these devices, novel methods of improving the thermal performance of fin stacks attached to the heat pipe condenser section are required. The current work investigates the use of a wing type surface protrusions in the form of 3-D delta wing tabs adhered to the fin surface, thin wings punched-out of the fin material and TiNi shape memory alloy delta wings which changed their angles of attack based on the fin surface temperature. The longitudinal vortices generated from the wing designs induce secondary mixing of the cooler free stream air entering the fin stack with the warmer fluid close to the fin surfaces. The change in angle of the attack of the active delta wings provide heat transfer enhancement while managing flow pressure losses across the fin stack. A heat transfer enhancement of 37% compared to a plain fin stack was obtained from the 3-D tabs in a staggered arrangement. The punched-out delta wings in the staggered and inline arrangements provided enhancements of 30% and 26% respectively. Enhancements from the active delta wings were lower at 16%. However, as these devices reduce the pressure drop through the fin stack by approximately 19% in the de-activate position, over the activated position, a reduction in fan operating cost may be achieved for systems operating with inlet air temperatures below the maximum inlet temperature specification for the device. CFD analysis was also carried out to provide additional detail of the local heat transfer enhancement effects. The CFD results corresponded well with previously published reports and were consistent with the experimental findings. - Highlights: → Heat transfer enhancements of heat pipe fin stacks was successfully achieved using fixed and active delta

Figures du sage et du savoir païens dans le Libro de buen amor

Directory of Open Access Journals (Sweden)

Olivier Biaggini

2013-06-01

Full Text Available Au-delà de la simple relation de dépendance à ses sources, le Libro de buen amor élabore diverses figures du sage antique, tantôt comme producteur et garant d’une parole d’autorité (Aristote, tantôt, au contraire, comme pur personnage au seuil de la fiction (Virgile. Dans les deux cas, le traitement est largement parodique et remet en question une révérence trop stricte face au système des autorités. Le cas d’Ovide, qui relève conjointement des deux catégories précédentes, est particulièrement intéressant car il montre comment les noms liés à la tradition ovidienne (Ovidio, Nasón, mais aussi Pánfilo, don Amor, doña Venus… sont autant de masques que l’archiprêtre peut successivement adopter et rejeter. Enfin, l’exemplum introductif des Grecs et des Romains est centré sur la transmission du savoir antique pour le placer au fondement du savoir de l’archiprêtre lui-même tout en offrant une représentation de sa part d’incertitude.Más allá de la simple relación de dependencia respecto a sus fuentes, el Libro de buen amor elabora diversas figuras del sabio antiguo, sea como productor y garante de una palabra de autoridad (Aristóteles, sea, al contrario, como mero personaje al borde de la ficción (Virgilio. En ambos casos, el tratamiento aplicado se revela sumamente paródico y pone en tela de juicio una reverencia demasiado estricta para con el sistema de las autoridades. El caso de Ovidio, que corresponde simultáneamente a las dos categorías precedentes, resulta de especial interés al enseñar cómo los nombres ligados a la tradición ovidiana (Ovidio, Nasón, pero también Pánfilo, don Amor, doña Venus… llegan a ser máscaras que el arcipreste puede sucesivamente adoptar y rechazar. Por fin, el exemplum introductorio de los griegos y los romanos se centra en la transmisión del saber antiguo presentándolo como uno de los fundamentos del saber del propio arcipreste al mismo tiempo que ofrece una

Simulation study of a 3-D device integrating FinFET and UTBFET

KAUST Repository

Fahad, Hossain M.; Hu, Chenming; Hussain, Muhammad Mustafa

2015-01-01

By integrating 3-D nonplanar fins and 2-D ultrathin bodies, wavy FinFETs merge two formerly competing technologies on a silicon-on-insulator platform to deliver enhanced transistor performance compared with conventional trigate Fin

Numerical studies of static aeroelastic effects on grid fin aerodynamic performances

Directory of Open Access Journals (Sweden)

Chengde HUANG

2017-08-01

Full Text Available The grid fin is an unconventional control surface used on missiles and rockets. Although aerodynamics of grid fin has been studied by many researchers, few considers the aeroelastic effects. In this paper, the static aeroelastic simulations are performed by the coupled viscous computational fluid dynamics with structural flexibility method in transonic and supersonic regimes. The developed coupling strategy including fluid–structure interpolation and volume mesh motion schemes is based on radial basis functions. Results are presented for a vertical and a horizontal grid fin mounted on a body. Horizontal fin results show that the deformed fin is swept backward and the axial force is increased. The deformations also induce the movement of center of pressure, causing the reduction and reversal in hinge moment for the transonic flow and the supersonic flow, respectively. For the vertical fin, the local effective incidences are increased due to the deformations so that the deformed normal force is greater than the original one. At high angles of attack, both the deformed and original normal forces experience a sudden reduction due to the interference of leeward separated vortices on the fin. Additionally, the increment in axial force is shown to correlate strongly with the increment in the square of normal force.

Holocene climatic fluctuations and periodic changes in the Asian southwest monsoon region

Science.gov (United States)

Zhang, Wenxiang; Niu, Jie; Ming, Qingzhong; Shi, Zhengtao; Lei, Guoliang; Huang, Linpei; Long, Xian'e.; Chang, Fengqin

2018-05-01

Climatic changes in the Asian southwest monsoon (ASWM) during the Holocene have become a topic of recent studies. It is important to understand the patterns and causes of Holocene climatic changes and their relationship with global changes. Based on the climate proxies and wavelet analysis of Lugu Lake in the ASWM region, the climatic fluctuations and periodic changes in the ASWM region during the Holocene have been reconstructed with a high-precision chronology. The results indicate the intensification of ASWM began to increase with Northern Hemisphere low-latitude solar insolation (LSI) and solar activity during the early Holocene, and gradually decreased during the late Holocene, exhibiting an apparent synchrony with numerous records of ASWM region. Meanwhile, an apparent 1000-a quasi-periodic signal is present in the environment proxies, and it demonstrates that the environmental change in the ASWM region has been driven mainly by LSI and solar activity.

Integrated Rudder/Fin Concise Control Based on Frequency Domain Analysis

OpenAIRE

W. Guan; Z. J. Su; G. Q. Zhang

2013-01-01

This paper describes a concise robust controller design of integrated rudder and fin control system in use of the closed loop gain shaping algorithm (CGSA) strategy. Compared with the arbitrary selection of weighting function in integrated rudder and fin H∞ mixed sensitivity control design procedures, the CGSA methods provided a relatively more straightforward and concise design method. Simulations were described that the overall performance of each CGSA rudder and fin control loop and the in...

Les Vandales en Afrique du Nord – fossoyeurs ou héritiers de la romanitas ?

OpenAIRE

Vössing, Konrad

2014-01-01

Depuis l'œuvre monumentale de Christian Courtois de 1955, les Vandales n'ont pas attiré l'attention de beaucoup de chercheurs. Au cours des dernières décennies, cependant, et bien qu’il n’existe toujours pas de monographie en langue française, les choses ont changé. En outre, des clichés historiques tels que les « invasions barbares » et la « fin du monde antique » ont fait renaître un vif intérêt scientifique et suscité de nouvelles approches. Dans ce contexte, les Vandales jouent un rôle im...

Differential induction of four msx homeobox genes during fin development and regeneration in zebrafish.

Science.gov (United States)

Akimenko, M A; Johnson, S L; Westerfield, M; Ekker, M

1995-02-01

To study the genetic regulation of growth control and pattern formation during fin development and regeneration, we have analysed the expression of four homeobox genes, msxA, msxB, msxC and msxD in zebrafish fins. The median fin fold, which gives rise to the unpaired fins, expresses these four msx genes during development. Transcripts of the genes are also present in cells of the presumptive pectoral fin buds. The most distal cells, the apical ectodermal ridge of the paired fins and the cleft and flanking cells of the median fin fold express all these msx genes with the exception of msxC. Mesenchymal cells underlying the most distal cells express all four genes. Expression of the msx genes in the fin fold and fin buds is transient and, by 3 days after fertilization, msx expression in the median fin fold falls below levels detectable by in situ hybridization. Although the fins of adult zebrafish normally have levels of msx transcripts undetectable by in situ hybridization, expression of all four genes is strongly reinduced during regeneration of both paired and unpaired fins. Induction of msx gene expression in regenerating caudal fins occurs as early as 30 hours postamputation. As the blastema forms, the levels of expression increase and reach a maximum between the third and fifth days. Then, msx expression progressively declines and disappears by day 12 when the caudal fin has grown back to its normal size. In the regenerating fin, the blastema cells that develop at the tip of each fin ray express msxB and msxC. Cells of the overlying epithelium express msxA and msxD, but do not express msxB or msxC. Amputations at various levels along the proximodistal axis of the fin suggest that msxB expression depends upon the position of the blastema, with cells of the rapidly proliferating proximal blastema expressing higher levels than the cells of the less rapidly proliferating distal blastema. Expression of msxC and msxD is independent of the position of the blastema cell

Gene expression profiles of fin regeneration in loach (Paramisgurnus dabryanu).

Science.gov (United States)

Li, Li; He, Jingya; Wang, Linlin; Chen, Weihua; Chang, Zhongjie

2017-11-01

Teleost fins can regenerate accurate position-matched structure and function after amputation. However, we still lack systematic transcriptional profiling and methodologies to understand the molecular basis of fin regeneration. After histological analysis, we established a suppression subtraction hybridization library containing 418 distinct sequences expressed differentially during the process of blastema formation and differentiation in caudal fin regeneration. Genome ontology and comparative analysis of differential distribution of our data and the reference zebrafish genome showed notable subcategories, including multi-organism processes, response to stimuli, extracellular matrix, antioxidant activity, and cell junction function. KEGG pathway analysis allowed the effective identification of relevant genes in those pathways involved in tissue morphogenesis and regeneration, including tight junction, cell adhesion molecules, mTOR and Jak-STAT signaling pathway. From relevant function subcategories and signaling pathways, 78 clones were examined for further Southern-blot hybridization. Then, 17 genes were chosen and characterized using semi-quantitative PCR. Then 4 candidate genes were identified, including F11r, Mmp9, Agr2 and one without a match to any database. After real-time quantitative PCR, the results showed obvious expression changes in different periods of caudal fin regeneration. We can assume that the 4 candidates, likely valuable genes associated with fin regeneration, deserve additional attention. Thus, our study demonstrated how to investigate the transcript profiles with an emphasis on bioinformatics intervention and how to identify potential genes related to fin regeneration processes. The results also provide a foundation or knowledge for further research into genes and molecular mechanisms of fin regeneration. Copyright © 2017 Elsevier B.V. All rights reserved.

Comprehensive performance comparison of airfoil fin PCHEs with NACA 00XX series airfoil

Energy Technology Data Exchange (ETDEWEB)

Chen, Fei, E-mail: chenfei@iet.cn [Institute of Engineering Thermophysics, Chinese Academy of Sciences, Beijing 100190 (China); Heating Technology Research and Development Center, Beijing District Heating Group, Beijing 100028 (China); Zhang, Lishen, E-mail: lishenzhang@sina.com [Heating Technology Research and Development Center, Beijing District Heating Group, Beijing 100028 (China); Huai, Xiulan, E-mail: hxl@iet.cn [Institute of Engineering Thermophysics, Chinese Academy of Sciences, Beijing 100190 (China); Li, Jufeng, E-mail: lijufeng.net@163.com [Nuclear and Radiation Safety Center, Ministry of Environmental Protection, Beijing 100082 (China); Zhang, Hang, E-mail: zhanghang@iet.cn [Institute of Engineering Thermophysics, Chinese Academy of Sciences, Beijing 100190 (China); Liu, Zhigang, E-mail: zgliu9322@163.com [Energy Research Institute of Shandong Academy of Sciences, Jinan, Shandong 250014 (China)

2017-04-15

Highlights: • Pressure drop of NACA 0020 airfoil fin PCHE reduces strikingly in comparison with the zigzag PCHE. • Pressure drop of NACA 00XX airfoil fin PCHE decreases as airfoil thickness increases. • Heat transfer performance of NACA 00XX airfoil fin PCHE increases as airfoil thickness rises. • Comprehensive performance of NACA 00XX airfoil fin PCHE degrades as airfoil thickness increases. - Abstract: Printed circuit heat exchanger (PCHE) can be used in supercritical carbon dioxide (S-CO{sub 2}) Brayton cycle. The present study compares NACA 0020 airfoil fin PCHE with conventional zigzag PCHE by numerical analysis. Pressure drop of the former has a striking reduction while maintaining excellent heat transfer performance. Comparison on four NACA 00XX series airfoil fin PCHEs is performed to investigate the influence of airfoil profile on flow and heat transfer performance. With a fixed vertical pitch, heat transfer performance of NACA series airfoil fin PCHE increases as airfoil thickness increases. However, comprehensive performance, in which both flow and heat transfer are taken into account, degrades with increasing airfoil thickness. Among four NACA airfoil fin PCHEs presented in this paper, NACA 0010 airfoil fin PCHE demonstrates the best comprehensive performance.

Comprehensive performance comparison of airfoil fin PCHEs with NACA 00XX series airfoil

International Nuclear Information System (INIS)

Chen, Fei; Zhang, Lishen; Huai, Xiulan; Li, Jufeng; Zhang, Hang; Liu, Zhigang

2017-01-01

Highlights: • Pressure drop of NACA 0020 airfoil fin PCHE reduces strikingly in comparison with the zigzag PCHE. • Pressure drop of NACA 00XX airfoil fin PCHE decreases as airfoil thickness increases. • Heat transfer performance of NACA 00XX airfoil fin PCHE increases as airfoil thickness rises. • Comprehensive performance of NACA 00XX airfoil fin PCHE degrades as airfoil thickness increases. - Abstract: Printed circuit heat exchanger (PCHE) can be used in supercritical carbon dioxide (S-CO_2) Brayton cycle. The present study compares NACA 0020 airfoil fin PCHE with conventional zigzag PCHE by numerical analysis. Pressure drop of the former has a striking reduction while maintaining excellent heat transfer performance. Comparison on four NACA 00XX series airfoil fin PCHEs is performed to investigate the influence of airfoil profile on flow and heat transfer performance. With a fixed vertical pitch, heat transfer performance of NACA series airfoil fin PCHE increases as airfoil thickness increases. However, comprehensive performance, in which both flow and heat transfer are taken into account, degrades with increasing airfoil thickness. Among four NACA airfoil fin PCHEs presented in this paper, NACA 0010 airfoil fin PCHE demonstrates the best comprehensive performance.

Necropsy report of a fin whale (Balaenoptera physalus) stranded in Denmark in 2010

DEFF Research Database (Denmark)

Alstrup, Aage K. O.; Hedayat, Abdi; Jensen, Trine Hammer

2013-01-01

There is little detailed information on stranded fin whales (Balaenoptera physalus) in the scientific literature (Notarbartolo di Sciara et al., 2003). In Denmark, at least eight fin whales stranded between the years 1603 and 1958 (Kinze, 1995). On 16 June 2010, a live subadult or adult male fin...... whale stranded in the Bay of Vejle (55º 69' N, 9º 58' E), Denmark. Despite several attempts, it was not possible to rescue the fin whale, which was only partially exposed by the water. The fin whale succumbed after 5 d stranded in shallow water. The dead fin whale was transported to a nearby pier...

FIN5 positively regulates far-red light responses in Arabidopsis thaliana

International Nuclear Information System (INIS)

Cho, D.S.; Hong, S.H.; Nam, H.G.; Soh, M.S.

2003-01-01

We report the characterization of a semi-dominant mutation fin5-1 (far-red insensitive 5-1) of Arabidopsis, which was isolated from genetic screening of phytochrome A (phyA) signaling components. Plants with the fin5-1 mutation exhibited a long hypocotyl phenotype when grown under far-red (FR) light, but not under red light. Physiological analyses implied that FIN5 might be differentially involved in diverse responses that are regulated by phyA under continuous FR light. Anthocyanin accumulation, gravitropic response of hypocotyl growth, and FR light-preconditioned blocking of greening were also impaired in the fin5-1 mutant, whereas photoperiodic floral induction was not, if at all, significantly affected. Moreover, light-regulated expression of the CHS, PORA and PsbS genes was attenuated in fin5-1 mutant plants, while the light-induced expression of CAB was normal. The mutation exhibited semi-dominance regarding control of hypocotyl growth in FR light. We suggest that FIN5 defines a novel branch in the network of phyA signaling in Arabidopsis. (author)

新加坡FinTech生态系统建设及其启示%Singapore’s FinTech Ecological System Construction and Its Enlightenment

Institute of Scientific and Technical Information of China (English)

钟鸣长

2016-01-01

Since the financial crisis, the integration of finance and technology has become a new trend in global economic development, and become a hot issue in the political, business, and academic attention. Singapore government maps out a strategy and introduces a series of policies to build FinTech ecosystem, such as financial support, establishing FinTech SUB, and implementing regulatory sandbox. Thus, Singapore will transform the existing financial system, construct the FinTech hub, and become an intelligent country of S&T and intelligent financial center. However, Internet finance in China is still at the stage of FinTech1.0 currently, which appears to be fast, slant, and disordered. So it is urgent to be transformed and upgraded. Meanwhile, we should not only be fully aware of the necessity and urgency of FinTech ecosystem development, clarify the relation between Internet financial and FinTech, but also we should learn from Singapore’s advanced experience to develop the FinTech ecosystem in all aspects, for example, setting up specialized management institutions, determining specific development goals, providing financial support, promoting “Regulatory Sandbox”, mobilizing domestic and international market resources, and exerting the role of the government, market, and enterprises.%金融危机以来，金融与科技的融合成为全球经济发展的一股新潮流和趋势，成为政、商、学界关注的热点话题。新加坡从资金支持、搭建创业加速平台、推行监管沙盒等方面推出了打造FinTech生态系统的组合拳，旨在改造现有金融体系、建设FinTech枢纽中心，立志成为世界智慧科技大国和智慧金融中心。中国互联网金融目前总体上还处于FinTech1.0阶段，呈现一种“快、偏、乱”的现象，亟需转型与升级。因此，我们不仅要充分意识到FinTech产业发展的必要性和紧迫性，厘清互联网金融与Fin

The performance of a new gas to gas heat exchanger with strip fin

NARCIS (Netherlands)

Wang, J.; Hirs, Gerard; Rollmann, P.

1999-01-01

A compact gas to gas heat exchanger needs large heat transfer areas on both fluid sides. This can be realised by adding secondary surfaces. The secondary surfaces are plate fin, strip fin, and louvered fin, etc. The fins extend the heat transfer surfaces and promote turbulence. This paper presents a

Performance Analysis of a Self-Propelling Flat Plate Fin with Joint Compliance

Science.gov (United States)

Reddy, N. Srinivasa; Sen, Soumen; Pal, Sumit; Shome, Sankar Nath

2017-12-01

Fish fin muscles are compliant and they regulate the stiffness to suit different swimming conditions. This article attempts to understand the significance of presence of compliance in fin muscle with help of a flexible joint flat plate fin model. Blade element method is employed to model hydrodynamics and to compute the forces of interaction during motion of the plate within fluid. The dynamic model of self-propelling fin is developed through multi-body dynamics approach considering the hydrodynamic forces as external forces acting on the fin. The derived hydrodynamic model is validated with experiments on rigid flat plate fin. The effect of the joint stiffness and flapping frequency on the propulsion speed and efficiency is investigated through simulations using the derived and validated model. The propulsion efficiency is found to be highly influenced by the joint stiffness at a given flapping frequency. The fin attained maximum propulsion efficiency when the joint stiffness is tuned to a value at which flapping frequency matches near natural frequency of the fin. At this tuned joint stiffness and flapping frequency, the resulted Strouhal numbers are observed to fall within the optimum range (0.2 to 0.4) for maximized propulsion efficiency of flying birds and swimming aquatic animals reported in literature.

Robotic Pectoral Fin Thrust Vectoring Using Weighted Gait Combinations

Directory of Open Access Journals (Sweden)

John S. Palmisano

2012-01-01

Full Text Available A method was devised to vector propulsion of a robotic pectoral fin by means of actively controlling fin surface curvature. Separate flapping fin gaits were designed to maximize thrust for each of three different thrust vectors: forward, reverse, and lift. By using weighted combinations of these three pre-determined main gaits, new intermediate hybrid gaits for any desired propulsion vector can be created with smooth transitioning between these gaits. This weighted gait combination (WGC method is applicable to other difficult-to-model actuators. Both 3D unsteady computational fluid dynamics (CFD and experimental results are presented.

Heat transfer in laminar flow for a finned double - tube

International Nuclear Information System (INIS)

Colle, S.

1977-01-01

An analitical study of the steady-state heat transfer in laminar flow in finned double-tube heat exchangers is presented. The fins are plane, straight and continous, equally spaced and are fixed over the external surface of the inner tube. A constant peripheral temperature distribution is assumed to apply over the inner tube surface and each fin, and a constant peripheral heat flux is assumed to apply over the outer tube surface, while the overall heat flux is suposed to be uniform in the longitudinal direction of the duct. The prediction of the thermal performance of the finned double-tube is made by means of the relationship between the Nusselt number, the boundary conditions and the geometric characteristcs of the duct. (author) [pt

Holocene reef accretion: southwest Molokai, Hawaii, U.S.A.

Science.gov (United States)

Engels, Mary S.; Fletcher, Charles H.; Field, Michael E.; Storlazzi, Curt D.; Grossman, Eric E.; Rooney, John J.B.; Conger, Christopher L.; Glenn, Craig

2004-01-01

Two reef systems off south Molokai, Hale O Lono and Hikauhi (separated by only 10 km), show strong and fundamental differences in modern ecosystem structure and Holocene accretion history that reflect the influence of wave-induced near-bed shear stresses on reef development in Hawaii. Both sites are exposed to similar impacts from south, Kona, and trade-wind swell. However, the Hale O Lono site is exposed to north swell and the Hikuahi site is not. As a result, the reef at Hale O Lono records no late Holocene net accretion while the reef at Hikauhi records consistent and robust accretion over late Holocene time. Analysis and dating of 24 cores from Hale O Lono and Hikauhi reveal the presence of five major lithofacies that reflect paleo-environmental conditions. In order of decreasing depositional energy they are: (1) coral-algal bindstone; (2) mixed skeletal rudstone; (3) massive coral framestone; (4) unconsolidated floatstone; and (5) branching coral framestone-bafflestone. At Hale O Lono, 10 cores document a backstepping reef ranging from ∼ 8,100 cal yr BP (offshore) to ∼ 4,800 cal yr BP (nearshore). A depauperate community of modern coral diminishes shoreward and seaward of ∼ 15 m depth due to wave energy, disrupted recruitment activities, and physical abrasion. Evidence suggests a change from conditions conducive to accretion during the early Holocene to conditions detrimental to accretion in the late Holocene. Reef structure at Hikauhi, reconstructed from 14 cores, reveals a thick, rapidly accreting and young reef (maximum age ∼ 900 cal yr BP). Living coral cover on this reef increases seaward with distance from the reef crest but terminates at a depth of ∼ 20 m where the reef ends in a large sand field. The primary limitation on vertical reef growth is accommodation space under wave base, not recruitment activities or energy conditions. Interpretations of cored lithofacies suggest that modern reef growth on the southwest corner of Molokai, and by

Réflexion sur l’origine du processus de segmentation du marche du travail

Directory of Open Access Journals (Sweden)

Attia Nicole

2006-01-01

Full Text Available (francuski Ce travail propose une réflexion sur l'origine du processus de segmentation du marché du travail par rapport à l'entreprise. Se situe-t-elle au sein même de l'entreprise ou en amont, c'est à dire entre les entreprises? Cela revient à se demander si on peut avoir une approche microéconomique ou macroéconomique de la segmentation et, à s'interroger sur le rôle réel tenu par les firmes dans le processus. Déterminant pour la théorie, ce rôle est à repenser selon la réponse apportée à notre question.

Propulsion of a fin whale (Balaenoptera physalus): why the fin whale is a fast swimmer.

Science.gov (United States)

Bose, N; Lien, J

1989-07-22

Measurements of an immature fin whale (Balaenoptera physalus), which died as a result of entrapment in fishing gear near Frenchmans Cove, Newfoundland (47 degrees 9' N, 55 degrees 25' W), were made to obtain estimates of volume and surface area of the animal. Detailed measurements of the flukes, both planform and sections, were also obtained. A strip theory was developed to calculate the hydrodynamic performance of the whale's flukes as an oscillating propeller. This method is based on linear, two-dimensional, small-amplitude, unsteady hydrofoil theory with correction factors used to account for the effects of finite span and finite amplitude motion. These correction factors were developed from theoretical results of large-amplitude heaving motion and unsteady lifting-surface theory. A model that makes an estimate of the effects of viscous flow on propeller performance was superimposed on the potential-flow results. This model estimates the drag of the hydrofoil sections by assuming that the drag is similar to that of a hydrofoil section in steady flow. The performance characteristics of the flukes of the fin whale were estimated by using this method. The effects of the different correction factors, and of the frictional drag of the fluke sections, are emphasized. Frictional effects in particular were found to reduce the hydrodynamic efficiency of the flukes significantly. The results are discussed and compared with the known characteristics of fin-whale swimming.

Nurturing a FinTech Ecosystem

DEFF Research Database (Denmark)

Leong, Carmen; Tan, Barney; Xiao, Xiao

2017-01-01

Financial technology, or FinTech, involves the design and delivery of financial products and services through technology. It impacts financial institutions, regulators, customers, and merchants across a wide range of industries. Pervasive digital technologies are challenging the fundamentals...... of the highly regulated financial sector, leading to the emergence of non-traditional payment systems, peer-to-peer money exchanges and increased turbulence in currency markets. This case study explores the development of a FinTech company in China that offers microloans to college students. Five lessons...... learned are presented for organizations to better manage the challenges and to leverage the opportunities amidst the disruption of financial sector. Our findings also shed light on how digital technology 1) offers the strategic capability for a firm to occupy a market niche in financial sector, 2) enables...

Optimization of geometric parameters of heat exchange pipes pin finning

Science.gov (United States)

Akulov, K. A.; Golik, V. V.; Voronin, K. S.; Zakirzakov, A. G.

2018-05-01

The work is devoted to optimization of geometric parameters of the pin finning of heat-exchanging pipes. Pin fins were considered from the point of view of mechanics of a deformed solid body as overhang beams with a uniformly distributed load. It was found out under what geometric parameters of the nib (diameter and length); the stresses in it from the influence of the washer fluid will not exceed the yield strength of the material (aluminum). Optimal values of the geometric parameters of nibs were obtained for different velocities of the medium washed by them. As a flow medium, water and air were chosen, and the cross section of the nibs was round and square. Pin finning turned out to be more than 3 times more compact than circumferential finning, so its use makes it possible to increase the number of fins per meter of the heat-exchanging pipe. And it is well-known that this is the main method for increasing the heat transfer of a convective surface, giving them an indisputable advantage.

Numerical simulation of natural convection in annuli with internal fins

International Nuclear Information System (INIS)

Ha, Man Yeong; Kim, Joo Goo

2004-01-01

The solution for the natural convection in internally finned horizontal annuli is obtained by using a numerical simulation of time-dependent and two-dimensional governing equations. The fins existing in annuli influence the flow pattern, temperature distribution and heat transfer rate. The variations of the fin configuration suppress or accelerate the free convective effects compared to those of the smooth tubes. The effects of fin configuration, number of fins and ratio of annulus gap width to the inner cylinder radius on the fluid flow and heat transfer in annuli are demonstrated by the distribution of the velocity vector, isotherms and streamlines. The governing equations are solved efficiently by using a parallel implementation. The technique is adopted for reduction of the computation cost. The parallelization is performed with the domain decomposition technique and message passing between sub-domains on the basis of the MPI library. The results from parallel computation reveal in consistency with those of the sequential program. Moreover, the speed-up ratio shows linearity with the number of processor

Holocene paleoclimate inferred from salinity histories of adjacent lakes in southwestern Sicily (Italy)

Science.gov (United States)

Curry, B Brandon; Henne, Paul; Mezquita-Joanes, Francesc; Marrone, Federico; Pieri, Valentina; La Mantia, Tommaso; Calo, Camilla; Tinner, Willy

2016-01-01

Marked uncertainties persist regarding the climatic evolution of the Mediterranean region during the Holocene. For instance, whether moisture availability gradually decreased, remained relatively constant, or increased during the last 7000 years remains a matter of debate. To assess Holocene limnology, hydrology and moisture dynamics, the coastal lakes Lago Preola and Gorgo Basso, located in southwestern Sicily, were investigated through several stratigraphic analyses of ostracodes, including multivariate analyses of assemblages, transfer functions of salinity, and biochemical analyses of valves (Sr/Ca, δ18O and δ13C). During the early Holocene, the Gorgo Basso and Lago Preola ostracode records are similar. After an initial period of moderate salinity (1690–6100 mg/l from ca. 10,000–8190 cal yr BP), syndepositional or diagenetic dissolution of ostracode valves suggests that salinity declined to Greek civilization took root in Sicily (2600 cal yr BP), and it completely dominates the record during Roman occupation (roughly 2100 to 1700 cal yr BP). These freshwater conditions at Gorgo Basso suggest high effective moisture when evergreen olive-oak forests collapsed in response to increased Greco-Roman land use and fire. Ostracode valve geochemistry (Sr/Ca, δ18O) suggests significant changes in early vs. late Holocene hydrochemistry, either as changes in salinity or in the seasonality of precipitation. Harmonizing the autecological and geochemical data from Gorgo Basso suggests the latter was more likely, with relatively more late Holocene precipitation falling during the spring, summer, and fall, than winter compared to the early Holocene. Our ostracode-inferred paleosalinity data indicate that moisture availability did not decline during the late Holocene in the central Mediterranean region. Instead, moisture availability was lowest during the early Holocene, and most abundant during the late Holocene.

Collector Efficiency in Downward-Type Internal-Recycle Solar Air Heaters with Attached Fins

Directory of Open Access Journals (Sweden)

Chii-Dong Ho

2013-10-01

Full Text Available The internal-recycle operation effect on collector efficiency in downward-type rectangular solar air heaters with attached fins is theoretically investigated. It is found that considerable collector efficiency is obtainable if the collector has attached fins and the operation is carried out with internal recycling. The recycling operation increases the fluid velocity to decrease the heat transfer resistance, compensating for the undesirable effect of decreasing the heat transfer driving force (temperature difference due to remixing. The attached fins provide an enlarged heat transfer area. The order of performance in a device of same size is: double pass with recycle and fins > double pass with recycle but without fins > single pass without recycle and fins.

Embedded SMA wire actuated biomimetic fin: a module for biomimetic underwater propulsion

International Nuclear Information System (INIS)

Wang Zhenlong; Hang Guanrong; Wang Yangwei; Li Jian; Du Wei

2008-01-01

An embedded shape memory alloy (SMA) wire actuated biomimetic fin is presented, and based on this module for biomimetic underwater propulsion, a micro robot fish (146 mm in length, 30 g in weight) and a robot squid (242 mm in length, 360 g in weight) were developed. Fish swim by undulating their body and/or fins. Squid and cuttlefish can also swim by undulating their fins. To simplify engineering modeling, the undulating swimming movement is assumed to be the integration of the movements of many flexible bending segments connected in parallel or in series. According to this idea, a biomimetic fin which can bend flexibly was developed. The musculature of a cuttlefish fin was investigated to aid the design of the biomimetic fin. SMA wires act as 'muscle fibers' to drive the biomimetic fin just like the transverse muscles of the cuttlefish fin. During the bending phase, elastic energy is stored in the elastic substrate and skin, and during the return phase, elastic energy is released to power the return movement. Theorem analysis of the bending angle was performed to estimate the bending performance of the biomimetic fin. Experiments were carried out on single-face fins with latex rubber skin and silicone skin (SF-L and SF-S) to compare the bending angle, return time, elastic energy storage and reliability. Silicone was found to be the better skin. A dual-face fin with silicone skin (DF-S) was tested in water to evaluate the actuating performance and to validate the reliability. Thermal analysis of the SMA temperature was performed to aid the control strategy. The micro robot fish and robot squid employ one and ten DF-S, respectively. Swimming experiments with different actuation frequencies were carried out. The speed and steering radius of the micro robot fish reached 112 mm s −1 and 136 mm, respectively, and the speed and rotary speed of the robot squid reached 40 mm s −1 and 22° s −1 , respectively

Fin field effect transistor directionality impacts printing of implantation shapes

Science.gov (United States)

Wang, Xiren; Granik, Yuri

2018-01-01

In modern integrated circuit (IC) fabrication processes, the photoresist receives considerable illumination energy that is reflected by underlying topography during optical lithography of implantation layers. Bottom antireflective coating (BARC) is helpful to mitigate the reflection. Often, however, BARC is not used, because its removal is technically challenging, in addition to its relatively high economic cost. Furthermore, the advanced technology nodes, such as 14/10-nm nodes, have introduced fin field effect transistor (FinFET), which makes reflection from nonuniform silicon substrates exceptionally complicated. Therefore, modeling reflection from topography becomes obligatory to accurately predict printing of implantation shapes. Typically, FinFET is always fixed in one direction in realistic designs. However, the same implantation rectangle may be oriented in either horizontal or vertical direction. Then, there are two types of relations between the critical dimension (CD) and FinFET, namely a parallel-to and a perpendicular-to relation. We examine the fin directionality impact on CD. We found that this impact may be considerable in some cases. We use our in-house rigorous optical topography simulator to reveal underlining physical reasons. One of the major causes of the CD differences is that in the parallel orientation, the solid sidewalls of the fins conduct considerable light reflections unlike for the perpendicular orientation. This finding can aid the compact modeling in optical proximity correction of implantation masks.

Protective Role of Comfrey Leave Extracts on UV-induced Zebrafish Fin Damage

OpenAIRE

Cheng, Chien-Chung; Chou, Chi-Yuan; Chang, Yao-Chin; Wang, Hsuan-Wen; Wen, Chi-Chung; Chen, Yau-Hung

2014-01-01

In zebrafish, UV exposure leads to fin malformation phenotypes including fin reduction or absence. The present study evaluated UV-protective activities of comfrey leaves extracts in a zebrafish model by recording fin morphological changes. Chemopreventive effects of comfrey leave extracts were evaluated using Kaplan-Meier analysis and Cox proportional hazards regression. The results showed that (1) the mean times of return to normal fin in the UV+comfrey (50 and 100 ppm) groups were 3.43 and ...

Computational investigation of heat transfer and pressure drop in a typical louver fin-and-tube heat exchanger for various louver angles and fin pitches

Directory of Open Access Journals (Sweden)

Okbaz Abdulkerim

2017-01-01

Full Text Available In this study 3-D numerical simulations on heat transfer and pressure drop characteristics for a typical louver fin-and- double-row tube heat exchanger were carried out. The heat transfer improvement and the corresponding pressure drop amounts were investigated depending on louver angles, fin pitch and Reynolds number, and reported in terms of Colburn j-factor and Fanning friction factor f. The heat transfer improvement and the corresponding pressure drop amounts were investigated depending on louver angles between 20° ≤Ө≤ 30°, louver pitch of Lp=3.8 mm and frontal velocities of U between 1.22 m/s - 3 m/s. In addition, flow visualization of detailed flow features results, such as velocity vectors, streamlines and temperature counters have been shown to understand heat transfer enhancement mechanism. The present results indicated that louver angle and fin pitch noticeably affected the thermal and hydraulic performance of heat exchanger. It has been seen that increasing louver angle, increases thermal performance while decreasing hydraulic performance associated to pressure drop for fin pitches of 3.2 mm and 2.5 mm. Fin pitch determines the flow behaviour that for fin pitch of 2 mm, increasing louver angle decreased heat transfer and pressure drop. Velocity vectors and streamlines give considerable information about the flow whether it is duct directed or louver directed. For all conditions the flow is louver directed.

Characteristics and formation mechanism for stainless steel fiber with periodic micro-fins

Science.gov (United States)

Tang, Tao; Wan, Zhenping; Lu, Longsheng; Tang, Yong

2016-05-01

Metal fibers have been widely used in many industrial applications due to their unique advantages. In certain applications, such as catalyst supports or orthopedic implants, a rough surface or tiny outshoots on the surface of metal fibers to increase surface area are needed. However, it has not been concerned about the surface morphologies of metal fiber in the current research of metal fiber manufacturing. In this paper, a special multi-tooth tool composed of a row of triangular tiny teeth is designed. The entire cutting layer of multi-tooth tool bifurcates into several thin cutting layers due to tiny teeth involved in cutting. As a result, several stainless steel fibers with periodic micro-fins are produced simultaneously. Morphology of periodic micro-fins is found to be diverse and can be classified into three categories: unilateral plane, unilateral tapering and bilateral. There are two forming mechanisms for the micro-fins. One is that periodic burrs remained on the free side of cutting layer of a tiny tooth create micro-fins of stainless steel fiber produced by the next neighboring tiny tooth; the other is that the connections between two fibers stuck together come to be micro-fins if the two fibers are finally detached. Influence of cutting conditions on formation of micro-fins is investigated. Experimental results show that cutting depth has no significant effect on micro-fin formation, high cutting speed is conducive to micro-fin formation, and feed should be between 0.12 mm/r and 0.2 mm/r to reliably obtain stainless steel fiber with micro-fins. This research presents a new pattern of stainless steel fiber characterized by periodic micro-fins formed on the edge of fiber and its manufacturing method.

Original Paper Performances comparées du HDL-cholestérol et du ...

African Journals Online (AJOL)

CT/HDL-C) et du HDL-Cholestérol est le meilleur prédicteur du SMet chez les adultes béninois. .... (Canada) et du. Ministère de la Santé du Bénin. Le consentement éclairé écrit a été obtenu de chaque participant avant leur recrutement dans.

印度尼西亚FinTech生态圈的发展及机遇%Development and Opportunities of FinTech Ecosystem in Indonesia

Institute of Scientific and Technical Information of China (English)

熊琦

2018-01-01

印尼FinTech是新兴行业,自2014年以来呈现井喷式增长,其生态圈竞争优势主要体现在需求方面:潜在市场巨大,资本投入增长迅猛,但人才优势尚显不足,政策上积极学习国际经验,已推出"监管沙盒"和针对P2P的严格管控法规,从长远看能促进FinTech包容性发展;印尼银行渗透率低,银行分支机构少,物理基础设施建设不足,且印尼人的FinTech意识较弱,中国FinTech企业在印尼的个人消贷和中小企业融资领域将大有作为;可加大对印尼的资金支持以帮助当地建设,更好地进行合作发展FinTech行业,实现共赢.

A Novel Implementation of a Flexible Robotic Fin Actuated by Shape Memory Alloy

Institute of Scientific and Technical Information of China (English)

Qin Yan; Lei Wang; Bo Liu; Jie Yang; Shiwu Zhang

2012-01-01

In this paper,study of a novel flexible robotic-fin actuated by Shape Memory Alloy (SMA) is presented.The developed robotic fin is capable of implementing various 3-Dimensional (3D) motions,which plays an important role in robot propulsion and maneuverability.Firstly,the morphological and mechanics parameters of a real pectoral fin from a carp are investigated.Secondly,a detailed design of the flexible pectoral fin driven by SMA is presented according to the previous morphological and mechanics analyses.Thirdly,a simplified theoretical model on the SMA fin plate is derived.The thermodynamics of the SMA plate and the relationship between curvature and phase transformation are analyzed.Finally,several simulations and model experiments are conducted according to the previous analyses.The results of the experiments are useful for the control of the robotic fin.The experimental results reveal that the SMA actuated fin ray has a good actuating performance.

Régionalisation du recrutement du personnel de santé au Burkina ...

International Development Research Centre (IDRC) Digital Library (Canada)

Régionalisation du recrutement du personnel de santé au Burkina Faso ... le ministère a adopté une politique de recrutement régionalisé de certaines catégories du ... de comprendre le contexte dans lequel une telle stratégie a été formulée, ...

35 Typologie des eaux de surface du bassin du Sebou par multi ...

African Journals Online (AJOL)

PR BOKO

2Service de protection de la qualité de l'eau, Agence du Bassin Hydraulique du ... pour montrer l'évolution de la qualité biologique des eaux de surface du ..... Biological Indicators of Freshwater Pollution and Environmental Management,.

Quantitative Holocene climatic reconstructions for the lower Yangtze region of China

Science.gov (United States)

Li, Jianyong; Dodson, John; Yan, Hong; Wang, Weiming; Innes, James B.; Zong, Yongqiang; Zhang, Xiaojian; Xu, Qinghai; Ni, Jian; Lu, Fengyan

2018-02-01

Quantitative proxy-based and high-resolution palaeoclimatic datasets are scarce for the lower reaches of the Yangtze River (LYR) basin. This region is in a transitional vegetation zone which is climatologically sensitive; and as a birthplace for prehistorical civilization in China, it is important to understand how palaeoclimatic dynamics played a role in affecting cultural development in the region. We present a pollen-based and regionally-averaged Holocene climatic twin-dataset for mean total annual precipitation (PANN) and mean annual temperature (TANN) covering the last 10,000 years for the LYR region. This is based on the technique of weighted averaging-partial least squares regression to establish robust calibration models for obtaining reliable climatic inferences. The pollen-based reconstructions generally show an early Holocene climatic optimum with both abundant monsoonal rainfall and warm thermal conditions, and a declining pattern of both PANN and TANN values in the middle to late Holocene. The main driving forces behind the Holocene climatic changes in the LYR area are likely summer solar insolation associated with tropical or subtropical macro-scale climatic circulations such as the Intertropical Convergence Zone (ITCZ), Western Pacific Subtropical High (WPSH), and El Niño/Southern Oscillation (ENSO). Regional multi-proxy comparisons indicate that the Holocene variations in precipitation and temperature for the LYR region display an in-phase relationship with other related proxy records from southern monsoonal China and the Indian monsoon-influenced regions, but are inconsistent with the Holocene moisture or temperature records from northern monsoonal China and the westerly-dominated region in northwestern China. Overall, our comprehensive palaeoclimatic dataset and models may be significant tools for understanding the Holocene Asian monsoonal evolution and for anticipating its future dynamics in eastern Asia.

Holocene climate variability and oceanographic changes off western South Africa

Science.gov (United States)

Zhao, Xueqin; Dupont, Lydie; E Meadows, Michael; Schefuß, Enno; Bouimetarhan, Ilham; Wefer, Gerold

2017-04-01

South Africa is located at a critical transition zone between subtropical and warm-temperate climate zones influenced by the Indian and Atlantic oceans. Presently, the seasonal changes of atmospheric and oceanic systems induce a pronounced rainfall seasonality comprised of two different rainfall zones over South Africa. How did this seasonality develop during the Holocene? To obtain a better understanding of how South African climates have evolved during the Holocene, we conduct a comprehensive spatial-temporal approach including pollen and dinoflagellate cyst records from marine sediment samples retrieved from the Namaqualand mudbelt, a Holocene terrigenous mud deposit on the shelf of western South Africa. The representation of different vegetation communities in western South Africa is assessed through pollen analysis of surface sediments. This approach allows for climate reconstructions of the summer rainfall zone (SRZ) using Group 1 (Poaceae, Cyperaceae, Phragmites-type and Typha) and winter rainfall zone (WRZ) using Group 2 (Restionaceae, Ericaceae, Anthospermum, Stoebe/Elytropappus-type, Cliffortia, Passerina, Artemisia-type and Pentzia-type) from a single marine archive. The fossil pollen data from gravity core GeoB8331-4 indicate contrasting climate patterns in the SRZ and WRZ especially during the early and middle Holocene. The rainfall amount in the SRZ is dominated by insolation forcing, while in the WRZ it is mainly attributed to the latitudinal position of the southern westerlies. Dinoflagellate cyst data show significantly different oceanographic conditions associated with climate changes on land. High percentages of autotrophic taxa like Operculodinium centrocarpum and Spiniferites spp. indicate warm and stratified conditions during the early Holocene, suggesting reduced upwelling. In contrast, the middle Holocene is characterized by a strong increase in heterotrophic taxa in particular Lejeunecysta paratenella and Echinidinium spp., indicating cool

Caractérisation des sables et morphologie du fond du lac du ...

African Journals Online (AJOL)

Une analyse sédimentologique et minéralogique réalisée sur un cycle hydrologique entre octobre 2004 et août 2005 a permis d\\'évaluer les charges solides en suspension et de caractériser les sédiments du lac du barrage de Taabo. La concentration moyenne en matières en suspension (12 mg.L-1) et la turbidité ...

Caractérisation des sables et morphologie du fond du lac du ...

African Journals Online (AJOL)

Administrateur

Une analyse sédimentologique et minéralogique réalisée sur un cycle hydrologique entre octobre 2004 et août 2005 a permis d'évaluer les charges solides en suspension et de caractériser les sédiments du lac du barrage de Taabo. La concentration moyenne en matières en suspension (12 mg.L-1) et la turbidité ...

The FLUFF code for calculating finned surface heat transfer -description and user's guide

International Nuclear Information System (INIS)

Fry, C.J.

1985-08-01

FLUFF is a computer code for calculating heat transfer from finned surfaces by convection and radiation. It can also represent heat transfer by radiation to a partially emitting and absorbing medium within the fin cavity. The FLUFF code is useful not only for studying the behaviour of finned surfaces but also for deriving heat fluxes which can be applied as boundary conditions to other heat transfer codes. In this way models of bodies with finned surfaces may be greatly simplified since the fins need not be explicitly represented. (author)

Age estimation of burbot using pectoral fin rays, brachiostegal rays, and otoliths

Science.gov (United States)

Klein, Zachary B.; Terrazas, Marc M.; Quist, Michael C.

2014-01-01

Throughout much of its native distribution, burbot (Lota lota) is a species of conservation concern. Understanding dynamic rate functions is critical for the effective management of sensitive burbot populations, which necessitates accurate and precise age estimates. Managing sensitive burbot populations requires an accurate and precise non-lethal alternative. In an effort to identify a non-lethal ageing structure, we compared the precision of age estimates obtained from otoliths, pectoral fin rays, dorsal fin rays and branchiostegal rays from 208 burbot collected from the Green River drainage, Wyoming. Additionally, we compared the accuracy of age estimates from pectoral fin rays, dorsal fin rays and branchiostegal rays to those of otoliths. Dorsal fin rays were immediately deemed a poor ageing structure and removed from further analysis. Age-bias plots of consensus ages derived from branchiostegal rays and pectoral fin rays were appreciably different from those obtained from otoliths. Exact agreement between readers and reader confidence was highest for otoliths and lowest for branchiostegal rays. Age-bias plots indicated that age estimates obtained from branchiostegal rays and pectoral fin rays were substantially different from age estimates obtained from otoliths. Our results indicate that otoliths provide the most precise age estimates for burbot.

Engagez-vous, devenez délégué(e) du personnel du CERN

CERN Multimedia

Staff Association

2017-01-01

Dans notre ECHO N° 275, nous avons annoncé les élections à venir au Conseil du personnel du CERN. Dans le présent ECHO, nous vous informons du lancement du processus des élections qui débute par le dépôt des candidatures. Tous les titulaires, boursiers et associés, qui sont aussi membres de l’Association du personnel, peuvent s’engager et déposer leur candidature entre le 11 septembre à 08 h 00 et le 13 octobre 2017 à 17 h 00. N’hésitez plus, remplissez le formulaire de candidature, présentez-vous aux élections au Conseil du personnel afin de pouvoir représenter et défendre vos collègues du personnel du CERN. ÊTRE DÉLÉGUÉ(E), C’EST QUOI ? Poser la question à plusieurs d...

Evaluation of integrally finned cladding for LMFBR fuel pins

International Nuclear Information System (INIS)

Cantley, D.A.; Sutherland, W.H.

1975-01-01

An integral fin design effectively reduces the coolant temperature gradients within an LMFBR subassembly by redistributing coolant flow so as to reduce the maximum cladding temperature and increase the duct wall temperature. The reduced cladding temperatures are offset by strain concentrations resulting from the fin geometry, so there is little net effect on predicted fuel pin performance. The increased duct wall temperatures, however, significantly reduce the duct design lifetime so that the final conclusion is that the integral fin design is inferior to the standard wire wrap design. This result, however, is dependent upon the material correlations used. Advanced alloys with improved irradiation properties could alter this conclusion

Experimental study of flow friction characteristics of integral pin-fin tubes

International Nuclear Information System (INIS)

Ding Ming; Yan Changqi; Sun Licheng

2007-01-01

Friction characteristics of integral pin-fin tubes, through which lubricating-oil flowed vertically, were studied experimentally. Effects of the pitch, the height of fins and the machining direction on friction coefficient were analyzed. The experimental results showed that the friction coefficient of the integral pin-fro tube was obviously lager than that of smooth tube. Compared with other influential factors, the effect of the height of fins was dominant. Because the three-dimensional pin fin could disturb and destroy the boundary layer, when the Reynolds Number reached 200-300, the friction coefficient curve began to bend, that was, a turning point was appeared in the friction coefficient curve. (authors)

Comprehensive study of flow and heat transfer at the surface of circular cooling fin

Science.gov (United States)

Mityakov, V. Yu; Grekov, M. A.; Gusakov, A. A.; Sapozhnikov, S. Z.; Seroshtanov, V. V.; Bashkatov, A. V.; Dymkin, A. N.; Pavlov, A. V.; Milto, O. A.; Kalmykov, K. S.

2017-11-01

For the first time is proposed to combine heat flux measurements with thermal imaging and PIV (particle image velocimetry) for a comprehensive study of flow and heat transfer at the surface of the circular cooling fin. The investigated hollow fin is heated from within with saturated water steam; meanwhile the isothermal external surface simulates one of the perfect fin. Flow and heat transfer at the surface of the solid fin of the same size and shape, made of titanium alloy is investigated in the same regimes. Gradient Heat Flux Sensors (GHFS) were installed at different places of the fin surface. Velocity field around a cylinder, temperature field at the surface of the fin and heat flux for each rated time were obtained. Comprehensive method including heat flux measurement, PIV and thermal imaging allow to study flow and heat transfer at the surface of the fin in real time regime. The possibility to study flow and heat transfer for non-isothermal fins is shown; it is allow to improve traditional calculation of the cooling fins.

An IPMC-enabled bio-inspired bending/twisting fin for underwater applications

Science.gov (United States)

Palmre, Viljar; Hubbard, Joel J.; Fleming, Maxwell; Pugal, David; Kim, Sungjun; Kim, Kwang J.; Leang, Kam K.

2013-01-01

This paper discusses the design, fabrication, and characterization of an ionic polymer-metal composite (IPMC) actuator-based bio-inspired active fin capable of bending and twisting motion. It is pointed out that IPMC strip actuators are used in the simple cantilever configuration to create simple bending (flapping-like) motion for propulsion in underwater autonomous systems. However, the resulting motion is a simple 1D bending and performance is rather limited. To enable more complex deformation, such as the flapping (pitch and heaving) motion of real pectoral and caudal fish fins, a new approach which involves molding or integrating IPMC actuators into a soft boot material to create an active control surface (called a ‘fin’) is presented. The fin can be used to realize complex deformation depending on the orientation and placement of the actuators. In contrast to previously created IPMCs with patterned electrodes for the same purpose, the proposed design avoids (1) the more expensive process of electroless plating platinum all throughout the surface of the actuator and (2) the need for specially patterning the electrodes. Therefore, standard shaped IPMC actuators such as those with rectangular dimensions with varying thicknesses can be used. One unique advantage of the proposed structural design is that custom shaped fins and control surfaces can be easily created without special materials processing. The molding process is cost effective and does not require functionalizing or ‘activating’ the boot material similar to creating IPMCs. For a prototype fin (90 mm wide × 60 mm long × 1.5 mm thick), the measured maximum tip displacement was approximately 44 mm and the twist angle of the fin exceeded 10°. Lift and drag measurements in water where the prototype fin with an airfoil profile was dragged through water at a velocity of 21 cm s-1 showed that the lift and drag forces can be affected by controlling the IPMCs embedded into the fin structure. These

Contribution to the study of can deformations in the fuel elements of gas-graphite reactors during thermal cycling; Contribution a l'etude des deformations des gaines des elements combustibles de reacteur graphite-gaz au cours du cyclage thermique

Energy Technology Data Exchange (ETDEWEB)

Gauthron, M; Boudouresques, B; Delpeyroux, P [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires

1964-07-01

The cans of fuel cartridges used in reactors of the gas-graphite type have either longitudinal fins of variable thickness, short herring-bone fins, or else a mixture of the two. An important test of the strength of these cartridges is their behaviour during thermal cycling carried out in cells reproducing in-pile conditions. It has been observed during with rapid cooling that there occurs a shortening at the base of the fins which can be accompanied in particular by a compression effect at the fin type, which has a tendency to curl, and by a tractive force acting on the body of the can at the ends of the longitudinal fins; this last phenomenon can result in a fracturing of the welds at the extremities or of the ends of the cartridge. This report presents first of all the way in which the stress diagram can be drawn for a can touching the fuel, and then the effect of the ratchet along a fin fixed to a bar with or without grooves. Finally the importance is shown of the test cycling variables (temperature, heating and cooling rates). (authors) [French] Les gaines des cartouches combustibles des reacteurs de la filiere graphite-gaz comportent soit des ailettes longitudinales plus ou moins epaisses, soit de courtes ailettes a chevrons, soit un ensemble des deux. Un test important de la tenue des cartouches, est la tenue au cyclage thermique en cellule pour reproduire le comportement en pile. On a observe au cours des cyclages a refroidissement rapide, un raccourcissement a la base des ailettes qui peut s'accompagner notamment d'une mise en compression du sommet de l'ailette qui a tendance a friser, et d'une traction exercee sur le corps des gaines au bout des ailettes longitudinales; ce dernier phenomene peut se traduire par des ruptures de soudures d'extremites ou des parties terminales de la cartouche. Ce rapport presente d'abord la maniere dont peut etre trace le diagramme des contraintes dans une gaine liee au combustible, puis l'effet du rochet le long d

Evidence of Suess solar-cycle bursts in Holocene speleothem d18O records

DEFF Research Database (Denmark)

Knudsen, Mads Faurschou; Jacobsen, B. H.; Riisager, Peter

2012-01-01

Several studies indicate that changes in solar activity may have driven Holocene subtropical monsoon variability on decadal and centennial timescales, but the strength and nature of this link remains debated. In this study, we combine a recent mapping of the Holocene solar-cycle activity with four...... in driving centennial-scale changes in the hydrological cycle in the subtropics during the Holocene....

Fish's Muscles Distortion and Pectoral Fins Propulsion of Lift-Based Mode

Science.gov (United States)

Yang, S. B.; Han, X. Y.; Qiu, J.

As a sort of MPF(median and/or paired fin propulsion), pectoral fins propulsion makes fish easier to maneuver than other propulsion, according to the well-established classification scheme proposed by Webb in 1984. Pectoral fins propulsion is classified into oscillatory propulsion, undulatory propulsion and compound propulsion. Pectoral fins oscillatory propulsion, is further ascribable to two modes: drag-based mode and lift-based mode. And fish exhibits strong cruise ability by using lift-based mode. Therefore to robot fish design using pectoral fins lift-based mode will bring a new revolution to resources exploration in blue sea. On the basis of the wave plate theory, a kinematic model of fish’s pectoral fins lift-based mode is established associated with the behaviors of cownose ray (Rhinoptera bonasus) in the present work. In view of the power of fish’s locomotion from muscle distortion, it would be helpful benefit to reveal the mechanism of fish’s locomotion variation dependent on muscles distortion. So this study puts forward the pattern of muscles distortion of pectoral fins according to the character of skeletons and muscles of cownose ray in morphology and simulates the kinematics of lift-based mode using nonlinear analysis software. In the symmetrical fluid field, the model is simulated left-right symmetrically or asymmetrically. The results qualitatively show how muscles distortion determines the performance of fish locomotion. Finally the efficient muscles distortion associated with the preliminary dynamics is induced.

Performance investigation of an innovative offset strip fin arrays in compact heat exchangers

International Nuclear Information System (INIS)

Peng, Hao; Ling, Xiang; Li, Juan

2014-01-01

Highlights: • The effect of fin pitch, length and bending distance on thermal performance were presented. • The corresponding Re C values at the j and f slope changes are in the range of 2000–2100. • The numerical results showed a good agreement with the experimental data. • Local high Nu values near the channel inlet, decreasing through the flow directions. - Abstract: Experimental and numerical studies on the flow and heat transfer characteristics for an innovative offset strip fins compact heat exchangers were performed. First, five fin schemes were investigated with various air flow velocities and a constant inlet steam pressure by experiments. The Reynolds number ranged from 500 to 5000 at the air side. The experimental results indicated that the fin pitch (P f ), fin length (L f ) and fin bending distance (C f ) have a significant influence on thermal performance of fins. The Colburn factor j, friction factor f and ‘point of transition’ were calculated from the experimental data. Then, the thermal–hydraulic performances of the novel offset strip fins were analyzed numerically. The simulation results obtained are in agreement with experimental data. Based on these simulations, the maximum values for local Nu number are at the channel inlet which is due to the thermal entrance effect. The longitudinal vortexes near the fin region will increase velocity gradient and reduce the thickness of boundary layer to improve heat transfer. The main conclusion draws from this work will be helpful for future development and design of a high-efficiency heat exchangers involving offset strip fin structures

Thermoelectric generator with hinged assembly for fins

International Nuclear Information System (INIS)

Purdy, D.L.; Shapiro, Z.M.; Hursen, T.F.; Maurer, G.W.

1976-01-01

A cylindrical casing has a central shielded capsule of radioisotope fuel. A plurality of thermonuclear modules are axially arranged with their hot junctions resiliently pressed toward the shield and with their cold junctions adjacent a transition member having fins radiating heat to the environment. For each module, the assembly of transition member and fins is hinged to the casing for swinging to permit access to and removal of such module. A ceramic plate having gold layers on opposite faces prevents diffusion bonding of the hot junction to the shield

Heat transfer enhancement of phase change materials by fins under simultaneous charging and discharging

International Nuclear Information System (INIS)

Joybari, Mahmood Mastani; Haghighat, Fariborz; Seddegh, Saeid; Al-Abidi, Abduljalil A.

2017-01-01

Highlights: • CFD simulation of a finned triplex tube heat exchanger with PCM under simultaneous charging and discharging. • Developed fin configurations for SCD, compatible with natural convection. • More fins enhanced the heat transfer as long as natural convection was not suppressed. • Longer fins enhanced the heat transfer as long as natural convection was not suppressed. • The effect of fin thickness was negligible, similar to non-SCD conditions. - Abstract: Due to the inherent intermittency of renewable energy sources such as solar, latent heat thermal energy storage in phase change materials (PCMs) has received considerable attention. Among several techniques to enhance PCMs’ thermal conductivity, the majority of studies have focused on fin integration due to its simplicity, ease of manufacturing, and low cost. In this study, utilization of extended surfaces (by longitudinal fins) was investigated by development of a numerical model to study the performance of a triplex tube heat exchanger (TTHX) equipped with a PCM under simultaneous charging and discharging (SCD). Governing equations were developed and numerically solved using ANSYS Fluent v16.2. Three conventional fin geometries and six developed fin configurations were compared based on the temperature, liquid fraction, and natural convection behavior under both SCD and non-SCD conditions. The intensity of natural convection was investigated for different fins for the inside heating/outside cooling scenario based on the solid–liquid interface evolution over time. The results indicated that since the buoyancy forces induce upward melted PCM motion, the inner hot tube requires fins on its lower half, while the outer cold one should be extended from its upper half. It was concluded that the case with 3 hot tube fins and 1 cold tube fin is most compatible with natural convection and provides the best performance under SCD conditions.

Ecologie du phytoplancton du lac Kivu

Directory of Open Access Journals (Sweden)

Sarmento, H.

2008-01-01

Full Text Available Speciation within the African Coffee Pathogen. Cet article analyse s'il est avantageux d'utiliser le compost au lieu de l'engrais minéral pour produire la laitue dans la zone urbaine et péri-urbaine de Yaoundé. Les résultats de terrain montrent l'obtention de rendements et profits plus élevés lorsqu'on utilise le compost. Les résultats de la fonction de production Cobb-Douglas prouvent que l'utilisation du compost est statistiquement significative pour expliquer la variation de rendement de la laitue et que le compost est l'intrant le plus productif. D'autres résultats montrent que le compost fournit la matière organique utile au sol et que les besoins d'irrigation en eau de la culture sont réduits grâce à l'utilisation du compost. Par conséquent, malgré le fait que l'application du compost demande une main-d'oeuvre beaucoup plus élevée, son utilisation est généralement bénéfique pour les agriculteurs vivant aux alentours de Yaoundé. Les programmes de vulgarisation de cet intrant pour encourager son adoption devraient donc figurer parmi les points prioritaires dans la politique agricole du gouvernement camerounais.

Resolution of ray-finned fish phylogeny and timing of diversification.

Science.gov (United States)

Near, Thomas J; Eytan, Ron I; Dornburg, Alex; Kuhn, Kristen L; Moore, Jon A; Davis, Matthew P; Wainwright, Peter C; Friedman, Matt; Smith, W Leo

2012-08-21

Ray-finned fishes make up half of all living vertebrate species. Nearly all ray-finned fishes are teleosts, which include most commercially important fish species, several model organisms for genomics and developmental biology, and the dominant component of marine and freshwater vertebrate faunas. Despite the economic and scientific importance of ray-finned fishes, the lack of a single comprehensive phylogeny with corresponding divergence-time estimates has limited our understanding of the evolution and diversification of this radiation. Our analyses, which use multiple nuclear gene sequences in conjunction with 36 fossil age constraints, result in a well-supported phylogeny of all major ray-finned fish lineages and molecular age estimates that are generally consistent with the fossil record. This phylogeny informs three long-standing problems: specifically identifying elopomorphs (eels and tarpons) as the sister lineage of all other teleosts, providing a unique hypothesis on the radiation of early euteleosts, and offering a promising strategy for resolution of the "bush at the top of the tree" that includes percomorphs and other spiny-finned teleosts. Contrasting our divergence time estimates with studies using a single nuclear gene or whole mitochondrial genomes, we find that the former underestimates ages of the oldest ray-finned fish divergences, but the latter dramatically overestimates ages for derived teleost lineages. Our time-calibrated phylogeny reveals that much of the diversification leading to extant groups of teleosts occurred between the late Mesozoic and early Cenozoic, identifying this period as the "Second Age of Fishes."

Combined natural convection heat and mass transfer from vertical fin arrays

International Nuclear Information System (INIS)

Giri, A.; Narasimham, G.S.V.L.; Krishna Murthy, M.V.

2003-01-01

Natural convection transport processes play an important role in many applications like ice-storage air-conditioning. A mathematical formulation of natural convection heat and mass transfer over a shrouded vertical fin array is developed. The base plate is maintained at a temperature below the dew point of the surrounding moist air. Hence there occurs condensation of moisture on the base plate, while the fins may be partially or fully wet. A numerical study is performed by varying the parameters of the problem. The local and average Nusselt numbers decrease in streamwise direction and tend to approach fully developed values for sufficiently large values of the fin length. The results show that beyond a certain streamwise distance, further fin length does not improve the sensible and latent heat transfer performance, and that if dry fin analysis is used under moisture condensation conditions, the overall heat transfer will be underestimated by about 50% even at low buoyancy ratios

Optimization of convective-radiative fins by using differential quadrature element method

International Nuclear Information System (INIS)

Malekzadeh, P.; Rahideh, H.; Karami, G.

2006-01-01

A first endeavor to exploit the differential quadrature element method (DQEM) as a simple, accurate and computationally efficient numerical tool for the shape optimization of convective-radiating extended surfaces or fins is made. The formulations are general so that the spatial and spatial-temperature dependent geometrical and thermal parameters can easily be implemented. The thermal conductivity of the fin is assumed to vary as a linear function of the temperature. The effects of a convective-radiative condition at the fin tip and effective convective condition at the fin base are considered. The optimization of fins with uniform and step cross-sections is investigated. The accuracy of the method is demonstrated by comparing its results with those generated by Adomian's decomposition technique, Taylor transformation technique and finite difference method. It is shown that, using few grid points, highly accurate results are obtained. Less computational effort of the method with respect to the finite difference method is shown

Numerical simulation of a plate-fin heat exchanger with offset fins using porous media approach

Science.gov (United States)

Juan, Du; Hai-Tao, Zhao

2018-03-01

In this paper, the study was focused on a double flow plate-fin heat exchanger (PFHE) whose heat transfer element was offset staggered fin. Numerical simulations have been carried out to investigate the thermodynamic characteristics of a full-size PFHE via the porous media approach. Based on the numerical model, the effects of the dynamic viscosity and the locations of the inlet and outlet tubes on flow distribution and pressure drop of the PFHE were studied. The results showed that flow distribution of the PFHE was improved by increasing the dynamic viscosity. Therefore, the relationship between flow distribution and pressure drop was analyzed under various inlet velocity, and a correlation among flow distribution, pressure drop, and Reynolds number was derived. Finally, the middle-based strategy was proposed and numerically verified to improve flow distribution of the PFHE.

Numerical Modeling of Transient Heat Transfer in Longitudinal Fin

Directory of Open Access Journals (Sweden)

Farshad Panahizadeh

2017-11-01

Full Text Available The main objective of the present numerical study is to investigate the transient heat transfer in one kind of all-purpose longitudinal fin with the triangular profile. The lateral surface of the concerned fin and the tip of it are subjected to general situations included heat flux at the base and insulation on the tip. For this study developed a one dimensional in house code written by Fortran 90 programming language by using finite difference method with an implicit scheme in unsteady state condition. Generally, the result of this study in time variation state after 700 seconds is steady. The results also show the fin efficiency by increasing the time of study decreases due to a reduction in the total heat transfer which is happened in the fin. The grid independence study shows that for the number of nodes greater than 20 the result will not be changed and same as before. Finally, the result of Fortran code verified by commercial CFD code which relies on finite difference method and it was shown have a consistent agreement

Effect of storage media and time on fin explants culture in the ...

African Journals Online (AJOL)

The effect of storage media and time was investigated on fin explants culture in the goldfish (Carassius auratus). Fin explants under sterile conditions were able to produce cells at different storage media and time. On the outgrowth of cells, fin explants stored for seven days before culturing showed significantly higher growth ...

A thermal study of pipes with outer transverse fins

Directory of Open Access Journals (Sweden)

S. Gil

2016-10-01

Full Text Available This paper provides results of thermal investigations on pipes with outer transverse fins produced by placing a strip, being a form of helical spring which functions as a radiator, on the basis pipe. The investigations were carried out at the facility that enables measurements with respect to both natural and forced convection. Performance of the investigated pipes was assessed in relation to a non-finned pipe and a pipe welded with the use of Metal Active Gas (MAG technology. The experiments have shown that the finned pipe welding technology does not markedly affect their thermal efficiency, which has been confirmed by performed model calculations, while the welding technology has a crucial impact on their operating performance.

Fiche technique du spermogramme et du spermocytogramme ...

African Journals Online (AJOL)

En Afrique la stérilité du couple constitue un drame social. Selon l'OMS, environ 8 à 12 % des couples africains sont touchés par une infertilité. La responsabilité masculine dans la stérilité est comprise entre 30 à 40%. Les causes de l'infertilité masculine peuvent être l'impuissance et/ ou l'altération du sperme. L'étude de ...

High performance flexible CMOS SOI FinFETs

KAUST Repository

Fahad, Hossain M.

2014-06-01

We demonstrate the first ever CMOS compatible soft etch back based high performance flexible CMOS SOI FinFETs. The move from planar to non-planar FinFETs has enabled continued scaling down to the 14 nm technology node. This has been possible due to the reduction in off-state leakage and reduced short channel effects on account of the superior electrostatic charge control of multiple gates. At the same time, flexible electronics is an exciting expansion opportunity for next generation electronics. However, a fully integrated low-cost system will need to maintain ultra-large-scale-integration density, high performance and reliability - same as today\\'s traditional electronics. Up until recently, this field has been mainly dominated by very weak performance organic electronics enabled by low temperature processes, conducive to low melting point plastics. Now however, we show the world\\'s highest performing flexible version of 3D FinFET CMOS using a state-of-the-art CMOS compatible fabrication technique for high performance ultra-mobile consumer applications with stylish design. © 2014 IEEE.

Early and late Holocene glacial fluctuations and tephrostratigraphy, Cabin Lake, Alaska

Science.gov (United States)

Zander, Paul D.; Kaufman, Darrell S.; Kuehn, Stephen C.; Wallace, Kristi L.; Anderson, R. Scott

2013-01-01

Marked changes in sediment types deposited in Cabin Lake, near Cordova, Alaska, represent environmental shifts during the early and late Holocene, including fluctuations in the terminal position of Sheridan Glacier. Cabin Lake is situated to receive meltwater during periods when the outwash plain of the advancing Sheridan Glacier had aggraded. A brief early Holocene advance from 11.2 to 11.0 cal ka is represented by glacial rock flour near the base of the sediment core. Non-glacial lake conditions were restored for about 1000 years before the water level in Cabin Lake lowered and the core site became a fen. The fen indicates drier-than-present conditions leading up to the Holocene thermal maximum. An unconformity spanning 5400 years during the mid-Holocene is overlain by peat until 1110 CE when meltwater from Sheridan Glacier returned to the basin. Three intervals of an advanced Sheridan Glacier are recorded in the Cabin Lake sediments during the late Holocene: 1110–1180, 1260–1540 and 1610–1780 CE. The sedimentary sequence also contains the first five reported tephra deposits from the Copper River delta region, and their geochemical signatures suggest that the sources are the Cook Inlet volcanoes Redoubt, Augustine and Crater Peak, and possibly Mt Churchill in the Wrangell Volcanic field.

NW Pacific mid-depth ventilation changes during the Holocene

Science.gov (United States)

Rella, S.; Uchida, M.

2010-12-01

During the last 50 years the oxygen content of North Pacific Intermediate Water primarily originating in the Okhotsk Sea has declined suggesting decreased mid-depth water circulation, likely leading to changes in biological productivity in the NW Pacific realm and a decrease in CO2 drawdown. It is therefore of high interest to elucidate the climate-oceanic interconnections of the present interglacial period (Holocene) in the NW Pacific, in order to predict possible future climate and surface productivity changes associated with a decrease in mid-depth ventilation in this ecologically sensitive region. However, such efforts have been hampered so far by the lack of appropriate sediment cores with fast sedimentation rates during the Holocene. Core CK05-04 that was recovered in 2005 from off Shimokita peninsula, Japan, at ~1000 m depth shows sedimentation rates of ~80 cm/kyr during the Holocene and therefore presents an ideal opportunity to reconstruct for the first time the Holocene ventilation history of the NW Pacific Ocean. We employ Accelerator Mass Spectroscopy (NIES-TERRA, Tsukuba) radiocarbon analysis of co-existing benthic and planktonic foraminifera to conclude on the ventilation age of the mid-depth water using benthic-planktonic radiocarbon age differences. At the conference we would like to present the results.

Holocene sea-level changes in the Falkland Islands

Science.gov (United States)

Newton, Tom; Gehrels, Roland; Daley, Tim; Long, Antony; Bentley, Mike

2014-05-01

In many locations in the southern hemisphere, relative sea level (RSL) reached its maximum position during the middle Holocene. This highstand is used by models of glacial isostatic adjustment (GIA) to constrain the melt histories of the large ice sheets, particularly Antarctica. In this paper we present the first Holocene sea-level record from the Falkland Islands (Islas Malvinas), an archipelago located on the Patagonian continental shelf about 500 km east of mainland South America at a latitude of ca. 52 degrees. Unlike coastal locations in southernmost South America, Holocene sea-level data from the Falklands are not influenced by tectonics, local ice loading effects and large tidal ranges such that GIA and ice-ocean mass flux are the dominant drivers of RSL change. Our study site is a salt marsh located in Swan Inlet in East Falkland, around 50 km southwest of Stanley. This is the largest and best developed salt marsh in the Falkland Islands. Cores were collected in 2005 and 2013. Lithostratigraphic analyses were complemented by analyses of foraminifera, testate amoebae and diatoms to infer palaeoenvironments. The bedrock, a Permian black shale, is overlain by grey-brown organic salt-marsh clay, up to 90 cm thick, which, in a landward direction, is replaced by freshwater organic sediments. Overlying these units are medium-coarse sands with occasional pebbles, up to 115 cm thick, containing tidal flat foraminifera. The sandy unit is erosively overlain by a grey-brown organic salt-marsh peat which extends up to the present surface. Further away from the sea this unit is predominantly of freshwater origin. Based on 13 radiocarbon dates we infer that prior to ~9.5 ka sea level was several metres below present. Under rising sea levels a salt marsh developed which was suddenly drowned around 8.4 ka, synchronous with a sea-level jump known from northern hemisphere locations. Following the drowning, RSL rose to its maximum position around 7 ka, less than 0.5 m above

Characteristics of a micro-fin evaporator: Theoretical analysis and experimental verification

OpenAIRE

Zheng Hui-Fan; Fan Xiao-Wei; Wang Fang; Liang Yao-Hua

2013-01-01

A theoretical analysis and experimental verification on the characteristics of a micro-fin evaporator using R290 and R717 as refrigerants were carried out. The heat capacity and heat transfer coefficient of the micro-fin evaporator were investigated under different water mass flow rate, different refrigerant mass flow rate, and different inner tube diameter of micro-fin evaporator. The simulation results of the heat transfer coefficient are fairly in good a...

Influence de la présence de contaminants lors du recyclage des thermoplastiques Influence of contaminants during the recycling of thermoplastics

Directory of Open Access Journals (Sweden)

Casetta Mathilde

2013-11-01

Full Text Available Le recyclage des matières plastiques constitue un enjeu environnemental majeur en raison de la diminution des ressources pétrolières et du problème de la gestion des déchets en fin de vie. Toutefois, ce recyclage est rendu difficile par la présence d'additifs ou de pollutions au sein des polymères. L'objectif de cette communication est de présenter et de commenter deux principaux exemples permettant d'illustrer l'influence de la présence de contaminants sur les propriétés du matériau recyclé. Dans un cas, on étudiera l'influence de la méthode de recyclage sur les propriétés finales du matériau et dans l'autre cas, on cherchera à remédier à la diminution des propriétés mécaniques du polymère recyclé en compatibilisant le contaminant au sein du matériau plastique. The recycling of plastic materials represents a major environmental challenge due to the decrease of petroleum resources and the problem of end-of-life products management. However, the presence of additives or pollutants inside polymers generally makes the recycling more difficult. The aim of the presentation is to describe two main examples illustrating the influence of the presence of contaminants on the properties of recycled polymers. First, the influence of the recycling method on the final properties of the material will be studied. Then, the decrease of the mechanical properties of the recycled polymer will be overcome by compatibilizing the contaminant inside the plastic material.

Optimization design of LED heat dissipation structure based on strip fins

Science.gov (United States)

Xue, Lingyun; Wan, Wenbin; Chen, Qingguang; Rao, Huanle; Xu, Ping

2018-03-01

To solve the heat dissipation problem of LED, a radiator structure based on strip fins is designed and the method to optimize the structure parameters of strip fins is proposed in this paper. The combination of RBF neural networks and particle swarm optimization (PSO) algorithm is used for modeling and optimization respectively. During the experiment, the 150 datasets of LED junction temperature when structure parameters of number of strip fins, length, width and height of the fins have different values are obtained by ANSYS software. Then RBF neural network is applied to build the non-linear regression model and the parameters optimization of structure based on particle swarm optimization algorithm is performed with this model. The experimental results show that the lowest LED junction temperature reaches 43.88 degrees when the number of hidden layer nodes in RBF neural network is 10, the two learning factors in particle swarm optimization algorithm are 0.5, 0.5 respectively, the inertia factor is 1 and the maximum number of iterations is 100, and now the number of fins is 64, the distribution structure is 8*8, and the length, width and height of fins are 4.3mm, 4.48mm and 55.3mm respectively. To compare the modeling and optimization results, LED junction temperature at the optimized structure parameters was simulated and the result is 43.592°C which approximately equals to the optimal result. Compared with the ordinary plate-fin-type radiator structure whose temperature is 56.38°C, the structure greatly enhances heat dissipation performance of the structure.

A novel louvered fin design to enhance thermal and drainage performances during periodic frosting/defrosting conditions

International Nuclear Information System (INIS)

Kim, Min-Hwan; Kim, Hisuk; Kim, Dong Rip; Lee, Kwan-Soo

2016-01-01

Highlights: • Thermal and drainage performances of a novel design louvered fin were investigated. • The thermal performance of the asymmetric fin was improved in the re-frosting cycle. • The asymmetric louvered fin exhibited better drainage on the leading edge of fins. • Lower surface tension between fin surface and water droplet improved the drainage. - Abstract: The retention water on fin surface can significantly degrade the thermal performance of heat exchangers under periodic frosting/defrosting conditions, which also leads to a decrease in the energy efficiency of air-source heat pumps. A novel louvered fin design was suggested to improve the drainage and the thermal performance of heat exchanger. The novel louvered fin had an asymmetric louver arrangement by flattening two louvers on the leading edge. The retention water formed on fin surface markedly decreased the heat transfer rate of the conventional symmetric louvered fins in re-frosting cycles. On the other hand, the asymmetric louvered fins improved the drainage performance of the retention water, which enhanced the heat transfer rate. To identify the reason of the difference in drainage performance between two fin geometries, additional experiments were carried out with enlargement models. The improvement in drainage performance of the asymmetric fin design originated from the lowered surface tension between the fin surface and water droplet.

Métabolisme du méthanol chez les micro-organismes méthylotrophes Metabolism of Methanol in Methylotrophic Microorganisms (Bibliographic Review

Directory of Open Access Journals (Sweden)

Ballerini D.

2006-11-01

Full Text Available De nombreux travaux portant sur l'étude du métabolisme du méthanol chez les bactéries et les levures ont été publiés depuis la fin des années cinquante, et nous permettent d'avoir une meilleure connaissance des mécanismes d'assimilation de ce substrat par les micro-organismes. Cet article précise l'état actuel des connaissances acquises sur les mécanismes d'oxydation du méthanol et sur les deux voies biosynthétiques différentes, la voie sérine et le cycle des ribose-phosphates, trouvées chez les micro-organismes capables d'une croissance méthylotrophique. A great mony research reports on studies of the methanol metabolism in bacteria and yeast has been published since the end of the 1950s and give us a better understanding of the mechanisms by which this substrate is assimulated by microorganisms. This article reviéws the state-of-the-art of knowledge about methanol oxidation mechanisms and two different biosynthesis procedures, 1. e.the serine one and the cycle of the ribose-phosphates found in microorganisms capable of methylotrophic growth.

Enhancement of heat transfer from a continuously moving porous fin exposed in convective–radiative environment

International Nuclear Information System (INIS)

Bhanja, Dipankar; Kundu, Balaram; Aziz, Abdul

2014-01-01

Highlights: • Analytical model for thermal analysis of moving porous fins. • Heat transfer from the fin surface due to convection and radiation. • For practical design aspects, optimization analysis was carried out. • Comparative study was made between the solid and porous moving fins. • Porous moving fin has more heat transfer ability than the stationary fin. - Abstract: In the present article, an exercise has been devoted to establish an analytical model for the determination of temperature distribution, fin efficiency and optimum design parameters of a porous moving fin which is losing heat by simultaneous convection and radiation to its surroundings. For the adaptation of this consideration, the governing equation becomes highly nonlinear. An analytical technique called Adomian decomposition method (ADM) is proposed for the solution methodology. The accuracy of the analytic solution is validated by using a numeric scheme called finite difference method. The results indicate that the numerical data and analytical approach are in agreement with each other. As the present study is an analytic, it is extended to the analysis for determination of optimum dimensions of said fin by satisfying either the maximization of rate of heat transfer for a given fin volume or by the minimization of fin volume for a desired heat transfer rate. The study is further extended to the porous fin in stationary condition and it is found that porous fin in moving condition transfers more heat than stationary condition. Investigation has also been made on solid moving fin to compare the outcomes of these parameters

J.-P. Giraud, F. Pons, Th. Janin, dir., Nécropoles protohistoriques de la région de Castres (Tarn. Le Causse, Gourjade, Le Martinet. Volume 1 : études et synthèses, 276 p. ; volume 2 : catalogue des ensembles funéraires, 268 p. ; volume 3 : planches du mobilier, 231 p., DAF n° 94

Directory of Open Access Journals (Sweden)

Pierre-Yves Milcent

2006-05-01

Full Text Available Entre 1987 et 1995, plusieurs campagnes de fouilles préventives ont permis l'exploration de trois importantes nécropoles à incinération de la fin de l'âge du Bronze et du premier âge du Fer dans les environs de Castres, en Midi-Pyrénées. Trois volumes, l'un de planches, un autre de description et un troisième d'analyse et de synthèse, nous apportent, dans des délais qu'il faut saluer pour leur brièveté, la publication exhaustive d'un corpus exceptionnel par la quantité des informations collec...

An IPMC-enabled bio-inspired bending/twisting fin for underwater applications

International Nuclear Information System (INIS)

Palmre, Viljar; Pugal, David; Kim, Sungjun; Kim, Kwang J; Hubbard, Joel J; Fleming, Maxwell; Leang, Kam K

2013-01-01

This paper discusses the design, fabrication, and characterization of an ionic polymer–metal composite (IPMC) actuator-based bio-inspired active fin capable of bending and twisting motion. It is pointed out that IPMC strip actuators are used in the simple cantilever configuration to create simple bending (flapping-like) motion for propulsion in underwater autonomous systems. However, the resulting motion is a simple 1D bending and performance is rather limited. To enable more complex deformation, such as the flapping (pitch and heaving) motion of real pectoral and caudal fish fins, a new approach which involves molding or integrating IPMC actuators into a soft boot material to create an active control surface (called a ‘fin’) is presented. The fin can be used to realize complex deformation depending on the orientation and placement of the actuators. In contrast to previously created IPMCs with patterned electrodes for the same purpose, the proposed design avoids (1) the more expensive process of electroless plating platinum all throughout the surface of the actuator and (2) the need for specially patterning the electrodes. Therefore, standard shaped IPMC actuators such as those with rectangular dimensions with varying thicknesses can be used. One unique advantage of the proposed structural design is that custom shaped fins and control surfaces can be easily created without special materials processing. The molding process is cost effective and does not require functionalizing or ‘activating’ the boot material similar to creating IPMCs. For a prototype fin (90 mm wide × 60 mm long × 1.5 mm thick), the measured maximum tip displacement was approximately 44 mm and the twist angle of the fin exceeded 10°. Lift and drag measurements in water where the prototype fin with an airfoil profile was dragged through water at a velocity of 21 cm s −1 showed that the lift and drag forces can be affected by controlling the IPMCs embedded into the fin structure

Session du Conseil du CERN : le ministre britannique, Robert Jackson, souligne l'intérêt de on pays pour l'avenir du CERN : décisions du Conseil pour la mise en oeuvre des recommandations du Comité d'évaluation du CERN: départ anticipé pour 200 membres au moins du personnel - mise à jour de la méthode de calcule pour les contributions des Etats Membres au budget

CERN Multimedia

CERN Press Office. Geneva

1988-01-01

Session du Conseil du CERN : le ministre britannique, Robert Jackson, souligne l'intérêt de on pays pour l'avenir du CERN : décisions du Conseil pour la mise en oeuvre des recommandations du Comité d'évaluation du CERN: départ anticipé pour 200 membres au moins du personnel - mise à jour de la méthode de calcule pour les contributions des Etats Membres au budget

Laser Welding Of Finned Tubes Made Of Austenitic Steels

Directory of Open Access Journals (Sweden)

Stolecki M.

2015-09-01

Full Text Available This paper describes the technology of welding of finned tubes made of the X5CrNi1810 (1.4301 austenitic steel, developed at Energoinstal SA, allowing one to get high quality joints that meet the requirements of the classification societies (PN-EN 15614, and at the same time to significantly reduce the manufacturing costs. The authors described an automatic technological line equipped with a Trumph disc laser and a tube production technological process. To assess the quality of the joints, one performed metallographic examinations, hardness measurements and a technological attempt to rupture the fin. Analysis of the results proved that the laser-welded finned tubes were performed correctly and that the welded joints had shown no imperfections.

Simulation study of a 3-D device integrating FinFET and UTBFET

KAUST Repository

Fahad, Hossain M.

2015-01-01

By integrating 3-D nonplanar fins and 2-D ultrathin bodies, wavy FinFETs merge two formerly competing technologies on a silicon-on-insulator platform to deliver enhanced transistor performance compared with conventional trigate FinFETs with unprecedented levels of chip-area efficiency. This makes it suitable for ultralarge-scale integration high-performance logic at and beyond the 10-nm technology node.

Investigation on flow and heat transfer characteristics in rectangular channel with drop-shaped pin fins

Directory of Open Access Journals (Sweden)

Fengming Wang

2012-12-01

Full Text Available The flow and heat transfer characteristics inside a rectangular channel embedded with pin fins were numerically and experimentally investigated. Several differently shaped pin fins (i.e., circular, elliptical, and drop-shaped with the same cross-sectional areas were compared in a staggered arrangement. The Reynolds number based on the obstructed section hydraulic diameter (defined as the ratio of the total wetted surface area to the open duct volume available for flow was varied from 4800 to 8200. The more streamlined drop-shaped pin fins were better at delaying or suppressing separation of the flow passing through them, which decreased the aerodynamic penalty compared to circular pin fins. The heat transfer enhancement of the drop-shaped pin fins was less than that of the circular pin fins. In terms of specific performance parameters, drop-shaped pin fins are a promising alternative configuration to circular pin fins.

Multi-Mode Electric Actuator Dynamic Modelling for Missile Fin Control

Directory of Open Access Journals (Sweden)

Bhimashankar Gurav

2017-06-01

Full Text Available Linear first/second order fin direct current (DC actuator model approximations for missile applications are currently limited to angular position and angular velocity state variables. Furthermore, existing literature with detailed DC motor models is decoupled from the application of interest: tail controller missile lateral acceleration (LATAX performance. This paper aims to integrate a generic DC fin actuator model with dual-mode feedforward and feedback control for tail-controlled missiles in conjunction with the autopilot system design. Moreover, the characteristics of the actuator torque information in relation to the aerodynamic fin loading for given missile trim velocities are also provided. The novelty of this paper is the integration of the missile LATAX autopilot states and actuator states including the motor torque, position and angular velocity. The advantage of such an approach is the parametric analysis and suitability of the fin actuator in relation to the missile lateral acceleration dynamic behaviour.

FINCRUSH : a computer program for impact analysis of radioactive material transport cask with fins

International Nuclear Information System (INIS)

Ikushima, Takeshi

1997-05-01

In drop impact analyses for radioactive material transport cask with cooling fins, relationship between fin plastic deformation and fin energy absorption is used. This relationship was obtained by ORNL experiments and MONSER Co. in Canada. Based on ORNL experiments, a computer program FINCRUSH has been developed for rapid safety analysis of cask drop impact to obtain the maximum impact acceleration and the maximum fin deformation. Main features of FINCRUSH are as follows: (1) annulus fins on a cylindrical shell and plate fins on a disk can be treated, (2) it is capable of graphical representations for calculation results and fin absorption energy data and (3) not only main frame computer but also work stations (OS UNIX) and personal computer (OS Windows) are available for use of the FINCRUSH. In the paper, brief illustration of calculation method of FINCRUSH is presented. The second section presents comparisons between FINCRUSH and experimental results. The third section provides a use's guide for FINCRUSH. (author)

FINCRUSH : a computer program for impact analysis of radioactive material transport cask with fins

Energy Technology Data Exchange (ETDEWEB)

Ikushima, Takeshi [Japan Atomic Energy Research Inst., Tokai, Ibaraki (Japan). Tokai Research Establishment

1997-05-01

In drop impact analyses for radioactive material transport cask with cooling fins, relationship between fin plastic deformation and fin energy absorption is used. This relationship was obtained by ORNL experiments and MONSER Co. in Canada. Based on ORNL experiments, a computer program FINCRUSH has been developed for rapid safety analysis of cask drop impact to obtain the maximum impact acceleration and the maximum fin deformation. Main features of FINCRUSH are as follows: (1) annulus fins on a cylindrical shell and plate fins on a disk can be treated, (2) it is capable of graphical representations for calculation results and fin absorption energy data and (3) not only main frame computer but also work stations (OS UNIX) and personal computer (OS Windows) are available for use of the FINCRUSH. In the paper, brief illustration of calculation method of FINCRUSH is presented. The second section presents comparisons between FINCRUSH and experimental results. The third section provides a use`s guide for FINCRUSH. (author)

Line-edge roughness induced single event transient variation in SOI FinFETs

International Nuclear Information System (INIS)

Wu Weikang; An Xia; Jiang Xiaobo; Chen Yehua; Liu Jingjing; Zhang Xing; Huang Ru

2015-01-01

The impact of process induced variation on the response of SOI FinFET to heavy ion irradiation is studied through 3-D TCAD simulation for the first time. When FinFET biased at OFF state configuration (V gs = 0, V ds = V dd ) is struck by a heavy ion, the drain collects ionizing charges under the electric field and a current pulse (single event transient, SET) is consequently formed. The results reveal that with the presence of line-edge roughness (LER), which is one of the major variation sources in nano-scale FinFETs, the device-to-device variation in terms of SET is observed. In this study, three types of LER are considered: type A has symmetric fin edges, type B has irrelevant fin edges and type C has parallel fin edges. The results show that type A devices have the largest SET variation while type C devices have the smallest variation. Further, the impact of the two main LER parameters, correlation length and root mean square amplitude, on SET variation is discussed as well. The results indicate that variation may be a concern in radiation effects with the down scaling of feature size. (paper)

Determination of optimum fin profile for a zero-G capillary drained condenser

Science.gov (United States)

Mccormick, John A.; Valenzuela, Javier A.; Choudhury, Dipanker

1990-01-01

This paper presents the analytical formulation and numerical results for heat transfer in a high heat flux condenser that relies on capillary flow along shaped fins (Gregorig surfaces) and a drainage network embedded in the condenser walls. Results are shown for a variety of fin profile shapes in order to show the geometric trade-offs involved in seeking a maximum effective heat transfer coefficient for the fin. Predictions of the model show excellent agreement with previously reported measurements for steam. Based on this work, a profile has been selected for a 2 kW ammonia condenser currently under development for use in space. In that design the fin half width is 0.5 mm and the model predicts a heat transfer coefficient referred to the base of the fin of 9 W/sq cm deg C for a heat flux of 10/W sq cm at the base.

Recherches biologiques et pisciculture expérimentale du goujon (Gobio gobio L.

Directory of Open Access Journals (Sweden)

BRUNET R.

1972-07-01

Full Text Available 1.1. Le goujon Gobio gobio L. (sous-espèce gobio est un poisson de rivières peu rapides, à instinct grégaire, vivant sur fond de gravier entre la région salmonicole et la région cyprinicole. Il peut vivre de 5 à 7 années et se reproduire dès la seconde année. 1.2. Le goujon n'est pas un poisson migrateur comme les expériences réalisées par marquage tendent à le démontrer, mais ce poisson à forte capacité reproductrice peut passer par des périodes de prolifération ou de raréfaction. 1.3. Le goujon est un poisson de type Carnivore qui s'alimente normalement durant toute l'année. Les adultes se nourissent principalement à partir du benthos ; les proies sont, en ordre d'importance décroissante, des larves d'Insectes, des Crustacés, des Mollusques, des Vers et des Algues ou détritus végétaux. Les alevins s'alimentent principalement à partir du plancton ; la nourriture est de même nature qualitativement, mais quantitativement les Crustacés y sont beaucoup plus abondants que les Insectes. 1.4. Le goujon est fréquemment parasité par le Plathelminte Monogène du genre Diplozoon ; ce parasite peut infester 90 % de la population. Il est parfois parasité par un grand Nématode du genre Philometra qui envahit la cavité générale. 1.5. Le goujon pond au printemps et en été, mais le début de la ponte est nettement lié à la température de l'eau (minimum de + 16°C à + 17°C; la ponte est fractionnée, mais peut atteindre 4 000 à 5 000 œufs par femelle et par saison. L'œuf, blanc translucide, mesure 1,5 mm de diamètre; l'incubation est de 125 degrés/jour. L'essai d'élevage en aquarium prouve qu'une alimentation artificielle adaptée doit être possible. 1.6. La pisciculture des alevins est réalisée dans la région toulousaine et permet d'indiquer les normes souhaitables. Pour la ponte, des bassins de 1 000 m2 , avec pente de 1 % et fond de gravier, peuvent recevoir 500 géniteurs. La croissance des alevins d'un �

Thermal performance of circular convective–radiative porous fins with different section shapes and materials

International Nuclear Information System (INIS)

Hatami, M.; Ganji, D.D.

2013-01-01

Graphical abstract: - Highlights: • LSM is an accurate technique for simulating heat transfer in circular porous fins. • Rectangular, convex, triangular and exponential variable sections are considered. • Radiation and convection from porous fin are considered. • Effects of material and geometry on heat transfer from fins are studied. - Abstract: In this study, heat transfer and temperature distribution equations for circular convective–radiative porous fins are presented. It’s assumed that the thickness of circular fins varies with radius so four different shapes, rectangular, convex, triangular and exponential, are considered. The heat transfer through porous media is simulated using passage velocity from the Darcy’s model. After deriving equation for each geometry, Least Square Method (LSM) and fourth order Runge–Kutta method (NUM) are applied for predicting the temperature distribution in the porous fins. The selected porous fin’s materials are Al, SiC, Cu and Si 3 N 4 . Results reveal that LSM has very effective and accurate in comparison with the numerical results. As a main outcome, Si 3 N 4 -exponential section fin has the maximum amount of transferred heat among other fins

Quelques considérations sur l’histoire du bâtiment théâtral dans les villes danubiennes

Directory of Open Access Journals (Sweden)

Daniela Gheorghe

2012-01-01

Full Text Available Vers la fin du XVIe siècle et au début du XVIIe, commence en Europe la construction des bâtiments spécifiquement dédiés au théâtre. En Angleterre et en Espagne, les premiers édifices préservent la structure simple du lieu où on jouait avant : la cour d’auberge et le patio – modèles pour le théâtre élisabéthain et pour les corrales de comedias. En Italie, l’architecture théâtrale connut une autre évolution ; à la recherche du Beau idéal, on élève des élégants bâtiments clos, où la salle est richement ornée, où les décors créent l’illusion de perspective et où l’on utilise des machineries scéniques sophistiquées. Le modèle du théâtre « à l’italienne » allait être adopté, avec des variations, partout en Europe. Mais les coûts d’un tel édifice sont bien chers ; ils exigent un certain niveau de prospérité et de développement urbain. La tradition et le goût des habitants pour l’art du spectacle jouent, eux aussi, un rôle pas négligeable. Ce papier examine l’histoire du bâtiment théâtral dans les villes portuaires danubiennes, dans la perspective de l'influence qu'exerça le développement du commerce et des activités connexes sur la vie urbaine. Artère fluviale majeure de l’Europe, le Danube fut utilisé au long du temps par plusieurs réseaux marchands ; celles-ci ont contribué à l’essor des bourgs riverains et à l’ascension des couches moyennes. Ainsi se forme une bourgeoisie qui peut financer, d’une manière ou d’une autre, des théâtres municipaux et qui fournit un nombreux public payant. Il est vrai que cette évolution ne fut pas simultanée dans tout le bassin danubien ; des circonstances historiques diverses ont généré un décalage significatif, surtout entre la région occidentale et celle orientale du fleuve. Néanmoins, des similitudes existent, et le but de cet article est de les mettre en lumière.

Optimum length of finned pipe for waste heat recovery

International Nuclear Information System (INIS)

Soeylemez, M.S.

2008-01-01

A thermoeconomic feasibility analysis is presented yielding a simple algebraic optimization formula for estimating the optimum length of a finned pipe that is used for waste heat recovery. A simple economic optimization method is used in the present study by combining it with an integrated overall heat balance method based on fin effectiveness for calculating the maximum savings from a waste heat recovery system

Lakeside cemeteries in the Sahara: 5000 years of holocene population and environmental change.

Directory of Open Access Journals (Sweden)

Paul C Sereno

Full Text Available BACKGROUND: Approximately two hundred human burials were discovered on the edge of a paleolake in Niger that provide a uniquely preserved record of human occupation in the Sahara during the Holocene ( approximately 8000 B.C.E. to the present. Called Gobero, this suite of closely spaced sites chronicles the rapid pace of biosocial change in the southern Sahara in response to severe climatic fluctuation. METHODOLOGY/PRINCIPAL FINDINGS: Two main occupational phases are identified that correspond with humid intervals in the early and mid-Holocene, based on 78 direct AMS radiocarbon dates on human remains, fauna and artifacts, as well as 9 OSL dates on paleodune sand. The older occupants have craniofacial dimensions that demonstrate similarities with mid-Holocene occupants of the southern Sahara and Late Pleistocene to early Holocene inhabitants of the Maghreb. Their hyperflexed burials compose the earliest cemetery in the Sahara dating to approximately 7500 B.C.E. These early occupants abandon the area under arid conditions and, when humid conditions return approximately 4600 B.C.E., are replaced by a more gracile people with elaborated grave goods including animal bone and ivory ornaments. CONCLUSIONS/SIGNIFICANCE: The principal significance of Gobero lies in its extraordinary human, faunal, and archaeological record, from which we conclude the following: The early Holocene occupants at Gobero (7700-6200 B.C.E. were largely sedentary hunter-fisher-gatherers with lakeside funerary sites that include the earliest recorded cemetery in the Sahara.Principal components analysis of craniometric variables closely allies the early Holocene occupants at Gobero with a skeletally robust, trans-Saharan assemblage of Late Pleistocene to mid-Holocene human populations from the Maghreb and southern Sahara.Gobero was abandoned during a period of severe aridification possibly as long as one millennium (6200-5200 B.C.E.More gracile humans arrived in the mid-Holocene

Holocene reef development where wave energy reduces accommodation

Science.gov (United States)

Grossman, Eric E.; Fletcher, Charles H.

2004-01-01

Analyses of 32 drill cores obtained from the windward reef of Kailua Bay, Oahu, Hawaii, indicate that high wave energy significantly reduced accommodation space for reef development in the Holocene and produced variable architecture because of the combined influence of sea-level history and wave exposure over a complex antecedent topography. A paleostream valley within the late Pleistocene insular limestone shelf provided accommodation space for more than 11 m of vertical accretion since sea level flooded the bay 8000 yr BP. Virtually no net accretion (pile-up of fore-reef-derived rubble (rudstone) and sparse bindstone, and (3) a final stage of catch-up bindstone accretion in depths > 6 m. Coral framestone accreted at rates of 2.5-6.0 mm/yr in water depths > 11 m during the early Holocene; it abruptly terminated at ~4500 yr BP because of wave scour as sea level stabilized. More than 4 m of rudstone derived from the upper fore reef accreted at depths of 6 to 13 m below sea level between 4000 and 1500 yr BP coincident with late Holocene relative sea-level fall. Variations in the thickness, composition, and age of these reef facies across spatial scales of 10-1000 m within Kailua Bay illustrate the importance of antecedent topography and wave-related stress in reducing accommodation space for reef development set by sea level. Although accommodation space of 6 to 17 m has existed through most of the Holocene, the Kailua reef has been unable to catch up to sea level because of persistent high wave stress.

Relying on fin erosion to identify hatchery-reared brown trout in a Tennessee river

Science.gov (United States)

Meerbeek, Jonathan R.; Bettoli, Phillip William

2012-01-01

Hatchery-induced fin erosion can be used to identify recently stocked catchable-size brown trout Salmo trutta during annual surveys to qualitatively estimate contributions to a fishery. However, little is known about the longevity of this mark and its effectiveness as a short-term (≤ 1 year) mass-marking technique. We evaluated hatchery-induced pectoral fin erosion as a mass-marking technique for short-term stocking evaluations by stocking microtagged brown trout in a tailwater and repeatedly sampling those fish to observe and measure their pectoral fins. At Dale Hollow National Fish Hatchery, 99.1% (228 of 230) of microtagged brown trout in outdoor concrete raceways had eroded pectoral fins 1 d prior to stocking. Between 34 and 68 microtagged and 26-35 wild brown trout were collected during eight subsequent electrofishing samples. In a blind test based on visual examination of pectoral fins at up to 322 d poststocking, one observer correctly identified 91.7% to 100.0% (mean of 96.9%) of microtagged brown trout prior to checking for microtags. In the laboratory, pectoral fin length and width measurements were recorded to statistically compare the fin measurements of wild and microtagged hatchery brown trout. With only one exception, all pectoral fin measurements on each date averaged significantly larger for wild trout than for microtagged brown trout. Based on the number of pectoral fin measurements falling below 95% prediction intervals, 93.7% (148 of 158) of microtagged trout were correctly identified as hatchery fish based on regression models up to 160 d poststocking. Only 72.2% (70 of 97) of microtagged trout were identified correctly after 160 d based on pectoral fin measurements and the regression models. We concluded that visual examination of pectoral fin erosion was a very effective way to identify stocked brown trout for up to 322 d poststocking.

Late Holocene higher sea level and its radiocarbon dates in Okierabu-jima, Ryukyus

International Nuclear Information System (INIS)

Koba, Motoharu; Omoto, Kunio; Takahashi, Tatsuo.

1980-01-01

Okierabu-jima of the Ryukyu Islands, which is a poly-terraced Pleistocene raised coral reef island, doesn't have a Holocene raised coral reef, but coastal erosional features showing higher sea levels in Holocene. The authors obtained some data indicating the period of one of the Holocene higher sea levels. All radiocarbon dates concerning Okierabu-jima's Holocene sea-level changes are plotted on the date-height coordinates. The paleo sea level between 5000 and 2000 y. B. P. lies above the broken line drawn from 6 m below to 2.18 m above the present sea level. The period of the highest sea level in Holocene seems to be about 3000 to 2000 y. B. P. in this island. Its height is presumably 2.4 m a. s. l. derived on an average from heights of stacks and coastal benches in the almost all coasts of the island (Koba, 1974). Beach rocks were already formed at the landward extremity of the reef flat corresponding to the almost present sea level about 1300 y. B. P. (author)

Plan de Mercadeo para una “FinTech”.

OpenAIRE

Escalante Lee, Maria Alejandra

2016-01-01

Las empresas deben contar con una misión clara, estableciendo los objetivos de apoyo, diseñando una cartera de negocio sólida y coordinar sus estrategias a futuro, con el fin de cumplir las metas propuestas para entregar e intercambiar ofertas que tienen valor para los consumidores, clientes, socios y la sociedad en general. El presente trabajo de grado tiene como objetivo proponer un plan de mercadeo para la empresa Comyno una FinTech ubicada en Frankfurt am Main, en Alemania. Este tiene ...

Integral finned heater and cooler for stirling engines

Science.gov (United States)

Corey, John A.

1984-01-01

A piston and cylinder for a Stirling engine and the like having top and bottom meshing or nesting finned conical surfaces to provide large surface areas in close proximity to the working gas for good thermal (addition and subtraction of heat) exchange to the working gas and elimination of the usual heater and cooler dead volume. The piston fins at the hot end of the cylinder are perforated to permit the gas to pass into the piston interior and through a regenerator contained therein.

La population du Moyen-Orient et de l'Afrique du Nord contribue ...

International Development Research Centre (IDRC) Digital Library (Canada)

29 avr. 2016 ... Le degré d'apport au contenu varie grandement d'une population à l'autre. Si les habitants du Moyen-Orient et de l'Afrique du Nord (région MENA) utilisent Wikipédia, ils y contribuent cependant moins que les populations d'autres régions du monde. Le contenu au sujet de la région MENA est, le plus ...

Variability of East Asian summer monsoon precipitation during the Holocene and possible forcing mechanisms

Science.gov (United States)

Lu, Fuzhi; Ma, Chunmei; Zhu, Cheng; Lu, Huayu; Zhang, Xiaojian; Huang, Kangyou; Guo, Tianhong; Li, Kaifeng; Li, Lan; Li, Bing; Zhang, Wenqing

2018-03-01

Projecting how the East Asian summer monsoon (EASM) rainfall will change with global warming is essential for human sustainability. Reconstructing Holocene climate can provide critical insight into its forcing and future variability. However, quantitative reconstructions of Holocene summer precipitation are lacking for tropical and subtropical China, which is the core region of the EASM influence. Here we present high-resolution annual and summer rainfall reconstructions covering the whole Holocene based on the pollen record at Xinjie site from the lower Yangtze region. Summer rainfall was less seasonal and 30% higher than modern values at 10-6 cal kyr BP and gradually declined thereafter, which broadly followed the Northern Hemisphere summer insolation. Over the last two millennia, however, the summer rainfall has deviated from the downward trend of summer insolation. We argue that greenhouse gas forcing might have offset summer insolation forcing and contributed to the late Holocene rainfall anomaly, which is supported by the TraCE-21 ka transient simulation. Besides, tropical sea-surface temperatures could modulate summer rainfall by affecting evaporation of seawater. The rainfall pattern concurs with stalagmite and other proxy records from southern China but differs from mid-Holocene rainfall maximum recorded in arid/semiarid northern China. Summer rainfall in northern China was strongly suppressed by high-northern-latitude ice volume forcing during the early Holocene in spite of high summer insolation. In addition, the El Niño/Southern Oscillation might be responsible for droughts of northern China and floods of southern China during the late Holocene. Furthermore, quantitative rainfall reconstructions indicate that the Paleoclimate Modeling Intercomparison Project (PMIP) simulations underestimate the magnitude of Holocene precipitation changes. Our results highlight the spatial and temporal variability of the Holocene EASM precipitation and potential forcing

Bio-inspired flexible joints with passive feathering for robotic fish pectoral fins.

Science.gov (United States)

Behbahani, Sanaz Bazaz; Tan, Xiaobo

2016-05-04

In this paper a novel flexible joint is proposed for robotic fish pectoral fins, which enables a swimming behavior emulating the fin motions of many aquatic animals. In particular, the pectoral fin operates primarily in the rowing mode, while undergoing passive feathering during the recovery stroke to reduce hydrodynamic drag on the fin. The latter enables effective locomotion even with symmetric base actuation during power and recovery strokes. A dynamic model is developed to facilitate the understanding and design of the joint, where blade element theory is used to calculate the hydrodynamic forces on the pectoral fins, and the joint is modeled as a paired torsion spring and damper. Experimental results on a robotic fish prototype are presented to illustrate the effectiveness of the joint mechanism, validate the proposed model, and indicate the utility of the proposed model for the optimal design of joint depth and stiffness in achieving the trade-off between swimming speed and mechanical efficiency.

Ostentation et refus du travail chez Veblen : le cas des jeunes chômeurs et de la spécificité militaire

Directory of Open Access Journals (Sweden)

Sébastien Schehr

2007-10-01

Full Text Available Cette contribution entend interroger la notion de « refus du travail » chez Veblen, notamment dans son rapport à l’ostentation et à la symbolique des places. Elle comportera deux parties : la première où sera exposée et revisitée la thèse de Veblen sur la fonction du refus du travail comme signe distinctif de la classe de loisir ; la deuxième où nous confronterons l’héritage de Veblen à des phénomènes sociaux contemporains. À cette fin, nous nous appuierons sur le rapport au travail des jeunes chômeurs et, dans une moindre mesure, sur celui des militaires, pour montrer que le refus du travail reste un principe opératoire de différenciation des groupes sociaux.This article intends to evaluate the notion of “work refusal” which can be found within Veblen’s work about conspicuous consumption and the symbolic of places. This article is divided in two parts. First, we will expose and revise Veblen’s thesis about the function of “work refusal” as a distinctive mark of the Leisure Class. Secondly, we will confront Veblen’s heritage to contemporary social phenomenon. For that reason, we will study the cases of the relationship of employed youth to work and the military. We will show that the refusal work stays a main principle of differentiation within social groups.

The heartstrings mutation in zebrafish causes heart/fin Tbx5 deficiency syndrome.

Science.gov (United States)

Garrity, Deborah M; Childs, Sarah; Fishman, Mark C

2002-10-01

Holt-Oram syndrome is one of the autosomal dominant human "heart-hand" disorders, with a combination of upper limb malformations and cardiac defects. Holt-Oram syndrome is caused by mutations in the TBX5 gene, a member of a large family of T-box transcription factors that play important roles in cell-type specification and morphogenesis. In a screen for mutations affecting zebrafish cardiac function, we isolated the recessive lethal mutant heartstrings, which lacks pectoral fins and exhibits severe cardiac dysfunction, beginning with a slow heart rate and progressing to a stretched, non-functional heart. We mapped and cloned the heartstrings mutation and find it to encode the zebrafish ortholog of the TBX5 gene. The heartstrings mutation causes premature termination at amino acid 316. Homozygous mutant embryos never develop pectoral fin buds and do not express several markers of early fin differentiation. The total absence of any fin bud differentiation distinguishes heartstrings from most other mutations that affect zebrafish fin development, suggesting that Tbx5 functions very early in the pectoral fin induction pathway. Moderate reduction of Tbx5 by morpholino causes fin malformations, revealing an additional early requirement for Tbx5 in coordinating the axes of fin outgrowth. The heart of heartstrings mutant embryos appears to form and function normally through the early heart tube stage, manifesting only a slight bradycardia compared with wild-type siblings. However, the heart fails to loop and then progressively deteriorates, a process affecting the ventricle as well as the atrium. Relative to mammals, fish require lower levels of Tbx5 to produce malformed appendages and display whole-heart rather than atrial-predominant cardiac defects. However, the syndromic deficiencies of tbx5 mutation are remarkably well retained between fish and mammals.

The pelvic fin and girdle of Panderichthys and the origin of tetrapod locomotion.

Science.gov (United States)

Boisvert, Catherine A

2005-12-22

One of the most marked transformations in the vertebrate transition to land was that of fins to limbs. This transformation involved not only the generation of morphological novelties (digits, sacrum) but also a shift in locomotory dominance from the pectoral to the pelvic appendage. Despite its importance, the transformation from pelvic fin to hindlimb is the least studied and least well-documented part of this transformation, which is bracketed by the osteolepiform Eusthenopteron and the early tetrapods Ichthyostega and Acanthostega, but is not directly illuminated by any intermediate form. Panderichthys is the closest tetrapod relative currently represented by complete fossils, but its pelvic fin skeleton has not been described. Here, I present the only known articulated pelvic fin endoskeleton and associated partial pelvis of Panderichthys. The pelvic girdle is even less tetrapod-like than that of the osteolepiform Eusthenopteron, but the pelvic fin endoskeleton shares derived characteristics with basal tetrapods despite being more primitive than the pectoral fin of Panderichthys. The evolution of tetrapod locomotion appears to have passed through a stage of body-flexion propulsion, in which the pelvic fins played a relatively minor anchoring part, before the emergence of hindlimb-powered propulsion in the interval between Panderichthys and Acanthostega.

Mediterranean Fin Whales (Balaenoptera physalus) Threatened by Dolphin MorbilliVirus.

Science.gov (United States)

Mazzariol, Sandro; Centelleghe, Cinzia; Beffagna, Giorgia; Povinelli, Michele; Terracciano, Giuliana; Cocumelli, Cristiano; Pintore, Antonio; Denurra, Daniele; Casalone, Cristina; Pautasso, Alessandra; Di Francesco, Cristina Esmeralda; Di Guardo, Giovanni

2016-02-01

During 2011-2013, dolphin morbillivirus was molecularly identified in 4 stranded fin whales from the Mediterranean Sea. Nucleoprotein, phosphoprotein, and hemagglutinin gene sequences of the identified strain were highly homologous with those of a morbillivirus that caused a 2006-2007 epidemic in the Mediterranean. Dolphin morbillivirus represents a serious threat for fin whales.

Néotoponymie contestée à Potchefstroom / Tlokwe (Province du Nord-Ouest, Afrique du Sud

Directory of Open Access Journals (Sweden)

Myriam Houssay-Holzschuch

2010-09-01

Full Text Available Illustration 1 - Extrait du site de la municipalité de Potchefstroom / TlokweSource : http://www.potch.co.za/newsarchive/streetnames.htmlIllustration 2- Potchefstroom (Afrique du SudAuteur : Béatrice Obry-Guyot, début décembre 2007.Illustration 3 - Extrait du plan Google Map de PotchefstroomSource : Google Map.La question toponymique en Afrique du Sud sur la longue durée porte sur deux thèmes essentiels porteurs de controverses : le plurilinguisme et le marquage symbolique et mémoriel du te...

Petrographical and Geochemical Study of a Kimmeridgian Organic Sequence (Yorkshire Area, Uk Étude pétrographique et géochimique d'une séquence organique du Kimmeridgien (région du Yorkshire, Angleterre

Directory of Open Access Journals (Sweden)

Belin S.

2006-11-01

Full Text Available A metric organic sequence from the Kimmeridge Clay Formation of Yorkshire (UK has been extensively studied with petrographical and geochemical techniques in the aim to define more precisely depositional and preservational conditions of the organic matter. The organic content is ranging from 3 to 9%. As a petrographical tool, the use of scanning electron microscopy with backscattered electron mode is emphasized, because it provides an image of all the constituents of the sediment. The sediment displays a very thin lamination, consists of clays, coccoliths (dispersed or as fecal pellets and algal organic matter. The presence of organic matter brings about diagenesis and induces carbonate dissolution, pyrite precipitation and silicification. The depositional environment was probably quiet with a fluctuating intensity of anoxia of the sea floor. The beginning of the sequence is characterized by higher sedimentation rate and primary productivity. La formation de Kimmeridge Clay, sédiment argileux comprenant des bancs carbonatés et des niveaux enrichis en matière organique, représente l'équivalent latéral des roches mères du pétrole de mer du Nord (Douglas et Williams, 1981 ; Ebukanson et Kinghorn, 1985; Williams, 1986. Les transgressions marines de la fin du Jurassique créent des petits bassins épicontinentaux séparés les uns des autres par des hauts-fonds et dont la colonne d'eau est stratifiée, ayant à la base un niveau stagnant et anoxique (Oschmann, 1988. Les échantillons étudiés proviennent d'un forage réalisé en 1987, dans le bassin de Cleveland (Yorkshire, par l'Institut Français du Pétrole. Une étude géochimique antérieure a mis en évidence des cyclicités de la teneur en carbone organique (Herbin et al. , 1991. Environ 200 cycles ont été identifiés et calés par rapport aux zones d'ammonites. Un cycle métrique a été choisi dans la zone à Eudoxus et échantillonné tous les 10cm, dans le but de mieux comprendre

Thermal-Hydraulic Performance of a Corrugated Cooling Fin with Louvered Surfaces

DEFF Research Database (Denmark)

Sønderby, Simon Kaltoft; Hosseini, Seyed Mojtaba Mir; Rezaniakolaei, Alireza

2017-01-01

The main objective of the article is to investigate thermal-hydraulic performance of a corrugated cooling fin with louvered surfaces. The investigation is carried out using the fin geometry of one most commonly used liquid-to-air heat exchangers. The investigation was carried out by numerically...... simulating the airflow with louvered fin geometry. The simulation model was verified by comparing simulated j- and f-factors with the corresponding values of several experimental correlations. The j-factors deviated less than 10.7 % from two of the experimental correlations, whereas deviations ranging...

Holocene environmental change and archaeology, Yangtze River Valley, China: Review and prospects

Directory of Open Access Journals (Sweden)

Li Wu

2012-11-01

Full Text Available Holocene environmental change and environmental archaeology are important components of an international project studying the human-earth interaction system. This paper reviews the progress of Holocene environmental change and environmental archaeology research in the Yangtze River Valley over the last three decades, that includes the evolution of large freshwater lakes, Holocene transgression and sea-level changes, Holocene climate change and East Asian monsoon variation, relationship between the rise and fall of primitive civilizations and environmental changes, cultural interruptions and palaeoflood events, as well as relationship between the origin of agriculture and climate change. These research components are underpinned by the dating of lacustrine sediments, stalagmites and peat to establish a chronology of regional environmental and cultural evolution. Interdisciplinary and other environment proxy indicators need to be used in comparative studies of archaeological site formation and natural sedimentary environment in the upper, middle and lower reaches of the Yangtze River Valley. Modern technology such as remote sensing, molecular bioarchaeology, and virtual reality, should be integrated with currently used dating, geochemical, sedimentological, and palaeobotanical methods of analysis in environmental archaeology macro- and micro-studies, so as to provide a greater comprehensive insight into Holocene environmental and cultural interaction and change in the Yangtze River Valley area.

Paleohydrology reconstruction and Holocene climate variability in the South Adriatic Sea

Directory of Open Access Journals (Sweden)

G. Siani

2013-02-01

Full Text Available Holocene paleohydrology reconstruction is derived combining planktonic and benthic stable oxygen and carbon isotopes, sea surface temperatures (SSTs and oxygen isotope composition of seawater (δ18Ow from a high sedimentation core collected in the South Adriatic Sea (SAS. Core chronology is based on 10 AMS 14C measures on planktonic foraminifera and tephra layers. Results reveal two contrasted paleohydrological periods that reflect (i a marked lowering of δ18Ow/salinity during the early to mid-Holocene (11.5 ka to 6.3 ka, including the two-step sapropel S1 deposition, followed during the mid- to upper Holocene by (ii a prevailing period of increased salinity and enhanced arid conditions in the South Adriatic Basin. Superimposed on these trends, short-term centennial-scale hydrological events punctuated the Holocene period in the SAS. During the early to mid-Holocene, two main SST coolings together with prominent δ18Ow/salinity lowering delineate the sapropel S1 interruption and the post-sapropel phase between 7.3 to 6.3 ka. After 6 ka, centennial-scale δ18Ow and G. bulloides δ13C lowering, mostly centered between 3 to 0.6 ka, reflect short-term hydrological changes related to more intensive runoff of the Po and/or Apennine rivers. These short-term events, even of lesser amplitude compared to the early to mid-Holocene period, may have induced a lowering of sea surface density and consequently reduced and/or inhibited the formation of deep bottom waters in the SAS. Comparison of the emerging centennial- to millennial-scale hydrological record with previous climatic records from the central Mediterranean area and north of the Alps reveal possible synchronicities (within the radiocarbon-dating uncertainty between phases of lower salinity in the SAS and periods of wetter climatic conditions around the north-central Adriatic Sea. Finally, wavelet analyses provide new clues about the potential origin of climate variability in the SAS, confirming

Experimental testing of the thermal performance of finned air coolers

International Nuclear Information System (INIS)

Imhof, A.; Keller, J.; Koelliker, A.

1988-05-01

Finned heat exchangers are often used as regenerators in heat recovery systems or as a heat source for heat pump installations. These exchangers are usually operating as air coolers. Heat is extracted from the air flowing through the heat exchanger. If the fin temperature lies below the dew point at the air inlet, water vapour may be condensed, increasing the thermal performance of the cooler. If the air/water heat exchanger is installed outdoors, the blower is usually mounted directly at the exchaner's case. In general this leads to non-ideal air flow conditions. For the sizing of such components the manufacturers dispose of design rules which are based either on theoretical models or on experiments using a uniform air stream. These rules which are mostly internal codes of the individual companies presumably do not take into account some non-ideal conditions such as an inhomogeneous air flow, a poorly sized blower or an increased pressure drop between the fins due to condensed water vapour. Moreover, these codes are possibly not sophisticated enough to enable a correct sizing of the products for any given condition of operation, especially in heat pumps operating under condensation conditions. Therfore, the Swiss Federal Institute for Reactor Research (EIR) carried out a research program dealing with the thermal performance of commercially available finned air coolers. The results give a strong evidence that the sizing of finned air coolers involving a phase change in one of the heat transfer fluids is not yet a procedure belonging to the common knowledge of most of the manufacturers. Moreover, the correct sizing of the blower is at least as important as the sizing of the finned exchanger itself. However, it is evident that there are companies on the Swiss market which use already reliable design tools. 25 refs., 81 figs., 12 tabs

Fin Type Variation of Lionhead Strain Goldfish (Carassius auratus Offspring

Directory of Open Access Journals (Sweden)

M. Syaifudin

2007-12-01

Full Text Available  Lionhead strain goldfish (Carassius auratus inheritance produce many variations in phenotype qualitative traits of their offspring that is not common with the parents. Lionhead is an ornamental freshwater fish, they do not have a dorsal fin, but it is a beauty finfish, is popular to the people and have a high economic value. Of the 846 offspring of lionhead is produced in this experiment, and 57,7% of them have dorsal fin (42,3% normal, 13,1% of them have anal fin which did not similar with their parents, 58,6% caudal fin of them did not have similar to their parents. It might be caused by incompletely segregation in meiosis and many gen responsible to certain phenotype trait. Another abnormalities such as no anal fin, blindness, stumped and no pigmen in their gill lamella also occurred. Key words: Inheritance, fin, phenotype, abnormality   ABSTRAK Ikan maskoki strain lionhead menghasilkan keturunan dengan fenotip yang sangat bervariasi dan berbeda dengan induknya. Ikan ini merupakan ikan hias air tawar yang tidak memiliki sirip punggung namun tetap memiliki keindahan, sehingga menjadi begitu populer di masyarakat dan memiliki nilai ekonomi yang tinggi. Sebanyak 846 keturunan (anakan telah dihasilkan dalam percobaan ini, dan sebanyak 57,7% dari populasi tersebut memiliki sirip punggung (berarti 42,3% merupakan keturunan normal, 13,1% memiliki sirip dubur yang tidak mirip dengan induknya. Variasi keturunan ikan maskoki strain lionhead ini disebabkan oleh segregasi yang tidak sempurna dalam proses meiosis dan banyaknya gen yang terlibat dalam pembentukan penotip tertentu. Abnormalitas lainnya juga terjadi pada keturunan ikan maskoki strain lionhead ini, seperti tidak adanya sirip dubur, mata buta, tubuh pendek dan tidak adanya pigmen pada lemela insang Kata kunci: Keturunan, sirip, fenotip, abnormalitas  

A Comparative Study of Conventional and Tip-Fin Propeller Performance

DEFF Research Database (Denmark)

Andersen, Poul

1997-01-01

During more than a decade several attempts have been made to obtain higher propeller efficiencies by radically modifying the geometry in the tip region of the blade. In the tip-fin propeller a tip fin or winglet is attached to the blade tip and integrated into the blade in such a way that the bla...

Eddy current test of fin tubes for a heat exchanger

International Nuclear Information System (INIS)

KIm, Young Joo; Lee, Se Kyung; Chung, Min Hwa

1992-01-01

Eddy current probes were designed for the test of fin tubes. Fin tubes, often used for heat exchangers, have uneven outer and inner surfaces to enhance the heat emission. The surface roughness make it difficult to detect flaws employing eddy current test(ECT). In order to overcome the difficulties we performed two types of works, one is the delopment of ECT probes, and the other is the signal processing including fast Fourier transform and digital filtering. In the development of ECT probes, we adopted empirical design method. Our ECT probes for fin tubes are inside diameter type. And we are specially concerned about geometric features such as the widths of the coils composing an ECT probe. We fabricated four probes with various coil widths. Eddy current test was performed using those ECT probes on specimens with artificial flaws. After analyzing the output signals, we found that, in order for the effective testing, the width of a coil should be determined considering the pitch of the fins of a tube. And we also learned that the frequency filtering could improve the s/n ratio.

Impact of line edge roughness on the performance of 14-nm FinFET: Device-circuit Co-design

Science.gov (United States)

Rathore, Rituraj Singh; Rana, Ashwani K.

2018-01-01

With the evolution of sub-20 nm FinFET technology, line edge roughness (LER) has been identified as a critical problem and may result in critical device parameter variation and performance limitation in the future VLSI circuit application. In the present work, an analytical model of fin-LER has been presented, which shows the impact of correlated and uncorrelated LER on FinFET structure. Further, the influence of correlated and uncorrelated fin- LER on all electrical performance parameters is thoroughly investigated using the three-dimensional (3-D) Technology Computer Aided Design (TCAD) simulations for 14-nm technology node. Moreover, the impact of all possible fin shapes on threshold voltage (VTH), drain induced barrier lowering (DIBL), on-current (ION), and off-current (IOFF) has been compared with the well calibrated rectangular FinFET structure. In addition, the influence of all possible fin geometries on the read stability of six-transistor (6-T) Static-Random-Access-Memory (SRAM) has been investigated. The study reveals that fin-LER plays a vital role as it directly governs the electrostatics of the FinFET structure. This has been found that there is a high degree of fluctuations in all performance parameters for uncorrelated fin-LER type FinFETs as compared to correlated fin-LER with respect to rectangular FinFET structure. This paper gives physical insight of FinFET design, especially in sub-20 nm technology nodes by concluding that the impact of LER on electrical parameters are minimum for correlated LER.

Volcanic influence on centennial to millennial Holocene Greenland temperature change.

Science.gov (United States)

Kobashi, Takuro; Menviel, Laurie; Jeltsch-Thömmes, Aurich; Vinther, Bo M; Box, Jason E; Muscheler, Raimund; Nakaegawa, Toshiyuki; Pfister, Patrik L; Döring, Michael; Leuenberger, Markus; Wanner, Heinz; Ohmura, Atsumu

2017-05-03

Solar variability has been hypothesized to be a major driver of North Atlantic millennial-scale climate variations through the Holocene along with orbitally induced insolation change. However, another important climate driver, volcanic forcing has generally been underestimated prior to the past 2,500 years partly owing to the lack of proper proxy temperature records. Here, we reconstruct seasonally unbiased and physically constrained Greenland Summit temperatures over the Holocene using argon and nitrogen isotopes within trapped air in a Greenland ice core (GISP2). We show that a series of volcanic eruptions through the Holocene played an important role in driving centennial to millennial-scale temperature changes in Greenland. The reconstructed Greenland temperature exhibits significant millennial correlations with K + and Na + ions in the GISP2 ice core (proxies for atmospheric circulation patterns), and δ 18 O of Oman and Chinese Dongge cave stalagmites (proxies for monsoon activity), indicating that the reconstructed temperature contains hemispheric signals. Climate model simulations forced with the volcanic forcing further suggest that a series of large volcanic eruptions induced hemispheric-wide centennial to millennial-scale variability through ocean/sea-ice feedbacks. Therefore, we conclude that volcanic activity played a critical role in driving centennial to millennial-scale Holocene temperature variability in Greenland and likely beyond.

Bulletin du CRDI #124

International Development Research Centre (IDRC) Digital Library (Canada)

Les femmes jouent un rôle important dans les exploitations minières artisanales et à petite échelle en Afrique subsaharienne. De concert ... Couverture du livre: Une vie saine pour les femmes et les enfants vulnérables · Couverture du livre: Entre el activismo y la intervención · Couverture du livre: Revitalizing Health for All.

Bulletin du CRDI #125

International Development Research Centre (IDRC) Digital Library (Canada)

L'IOSRS remporte le prix de la diplomatie scientifique · GrowInclusive : la plateforme tant attendue est en construction · Toutes les nouvelles. Activités à venir. Semaine du développement international 2018. Le CRDI célébrera la Semaine du développement international du 4 au 10 février 2018. Suivez-nous sur Twitter et ...

A stable-isotope tree-ring timescale of the Late Glacial/Holocene boundary

International Nuclear Information System (INIS)

Becker, Bernd; Kromer, Bernd; Trimborn, Peter

1991-01-01

Late Glacial and Holocene tree-ring chronologies, like deep-sea sediments or polar ice cores, contain information about past environments. Changes in tree-ring growth rates can be related to past climate anomalies and changes in the isotope composition of tree-ring cellulose reflect changes in the composition of the atmosphere and the hydrosphere. We have established a 9,928-year absolutely dated dendrochronological record of Holocene oak (Quercus robur, Quercus petraea)-and a 1,604-year floating Late Glacial and Early Holocene chronology of pine (Pinus sylvestris) from subfossil tree remnants deposited in alluvial terraces of south central European rivers. The pine sequence provides records of dendro-dated 14 C, 13 C and 2 H patterns for the late Younger Dryas and the entire Preboreal (10,100-9,000 yr BP). Through the use of dendrochronology, radiocarbon age calibration and stable isotope analysis, we suggest that the Late Glacial/Holocene transition may be identified and dated by 13 C and 2 H tree-ring chronologies. (author)

The Honey-lips et The Guarani : les romans de José de Alencar en langue anglaise à la fin du XIXe siècle

Directory of Open Access Journals (Sweden)

Valéria Cristina Bezerra

2016-10-01

Full Text Available Dans les dernières décennies du XIXe siècle, deux romans de José de Alencar ont été traduits et obtenu circulation dans des pays de langue anglaise. Iraçéma : the honey-lips, version de Isabel Burton, est apparue en 1886 à Londres, em suscitant la réception critique dans des journaux du Royaume-Uni. The Guarany, traduit par James William Hawes, est sorti de façon découpée en 1893 dans le jornal Overland Monthly and Out West Magazine, de San Francisco, aux États-Unis, pays où Alencar a aussi été mentionné par la presse locale. Ce travail se propose d’analyser la réception de ces ouvrages et de José de Alencar dans le Royaume-Uni et les États- Unis. Il a également pour but de vérifier le rôle des traducteurs, éditeurs, critiques et de la presse dans la configuration de l’évaluation de cet écrivain et de ses oeuvres dans ces pays, en considérant, toujours que possible, le rapport de ces passeurs avec la culture brésilienne. La réception critique de Alencar dans ces pays révèle sa bonne évaluation aussi bien que la traduction de ses romans semble avoir répondu à l’intérêt du public étranger à s’illustrer.

« Comme à l’époque de Suzie Wong ». Les mutations du red-light district de Wan Chai

OpenAIRE

Paris, Nicolas

2011-01-01

Le roman exotique Le monde de Suzie Wong et ses nombreuses adaptations immortalisent le red-light district de Wan Chai à Hong Kong à la fin des années 1950, mettant en scène marins américains, expatriés de l’Empire britannique et prostituées hongkongaises. Aujourd’hui, avec la mondialisation, Wan Chai est fréquenté par des migrantes de plusieurs pays d’Asie du Sud-Est. Pourtant, le red-light district est toujours associé dans la presse et les guides de voyage à « l’époque de Suzie Wong ». Ces...

A successful application of homotopy perturbation method for efficiency and effectiveness assessment of longitudinal porous fins

International Nuclear Information System (INIS)

Cuce, Erdem; Cuce, Pinar Mert

2015-01-01

Highlights: • Homotopy perturbation method has been applied to porous fins. • Dimensionless efficiency and effectiveness expressions have been firstly developed. • Effects of porous and convection parameters on thermal analysis have been clarified. • Ratio of porous fin to solid fin heat transfer rate has been given for various cases. • Reliability and practicality of homotopy perturbation method has been illustrated. - Abstract: In our previous works, thermal performance of straight fins with both constant and temperature-dependent thermal conductivity has been investigated in detail and dimensionless analytical expressions of fin efficiency and fin effectiveness have been developed for the first time in literature via homotopy perturbation method. In this study, previous works have been extended to porous fins. Governing equations have been formulated by performing Darcy’s model. Dimensionless temperature distribution along the length of porous fin has been determined as a function of porosity and convection parameters. The ratio of porous fin to solid fin heat transfer rate has also been evaluated as a function of thermo-geometric fin parameter. The results have been compared with those of finite difference method for a specific case and an excellent agreement has been observed. The expressions developed are beneficial for thermal engineers for preliminary assessment of thermophysical systems instead of consuming time in heat conduction problems governed by strongly nonlinear differential equations

Comparative study on thermal performance of natural draft cooling towers with finned shells

International Nuclear Information System (INIS)

Goodarzi, Mohsen

2016-01-01

The cooling efficiency of natural draft cooling towers under crosswind condition should be improved. In the present research work three different externally finned shells were considered for a typical natural draft cooling tower to investigate the cooling improvement. They were numerically simulated under normal and crosswind conditions. Numerical results show that twisting four fin plates over the tower shell along the 45 peripheral angle, could improve the cooling efficiency up to 6.5 %. Because of the periodic shape of the fin plates, the cooling efficiency of the cooling tower with finned shell is less sensitive to the change of wind.

Comparative study on thermal performance of natural draft cooling towers with finned shells

Energy Technology Data Exchange (ETDEWEB)

Goodarzi, Mohsen [Bu-Ali Sina Univ., Hamedan (Iran, Islamic Republic of). Dept. of Mechanical Engineering

2016-10-15

The cooling efficiency of natural draft cooling towers under crosswind condition should be improved. In the present research work three different externally finned shells were considered for a typical natural draft cooling tower to investigate the cooling improvement. They were numerically simulated under normal and crosswind conditions. Numerical results show that twisting four fin plates over the tower shell along the 45 peripheral angle, could improve the cooling efficiency up to 6.5 %. Because of the periodic shape of the fin plates, the cooling efficiency of the cooling tower with finned shell is less sensitive to the change of wind.

Performance measurement of plate fin heat exchanger by exploration: ANN, ANFIS, GA, and SA

OpenAIRE

A.K. Gupta; P. Kumar; R.K. Sahoo; A.K. Sahu; S.K. Sarangi

2017-01-01

An experimental work is conducted on counter flow plate fin compact heat exchanger using offset strip fin under different mass flow rates. The training, testing, and validation set of data has been collected by conducting experiments. Next, artificial neural network merged with Genetic Algorithm (GA) utilized to measure the performance of plate-fin compact heat exchanger. The main aim of present research is to measure the performance of plate-fin compact heat exchanger and to provide full exp...

Biotic turnover rates during the Pleistocene-Holocene transition

Science.gov (United States)

Stivrins, Normunds; Soininen, Janne; Amon, Leeli; Fontana, Sonia L.; Gryguc, Gražyna; Heikkilä, Maija; Heiri, Oliver; Kisielienė, Dalia; Reitalu, Triin; Stančikaitė, Miglė; Veski, Siim; Seppä, Heikki

2016-11-01

The Northern Hemisphere is currently warming at the rate which is unprecedented during the Holocene. Quantitative palaeoclimatic records show that the most recent time in the geological history with comparable warming rates was during the Pleistocene-Holocene transition (PHT) about 14,000 to 11,000 years ago. To better understand the biotic response to rapid temperature change, we explore the community turnover rates during the PHT by focusing on the Baltic region in the southeastern sector of the Scandinavian Ice Sheet, where an exceptionally dense network on microfossil and macrofossil data that reflect the biotic community history are available. We further use a composite chironomid-based summer temperature reconstruction compiled specifically for our study region to calculate the rate of temperature change during the PHT. The fastest biotic turnover in the terrestrial and aquatic communities occurred during the Younger Dryas-Holocene shift at 11,700 years ago. This general shift in species composition was accompanied by regional extinctions, including disappearance of mammoth (Mammuthus primigenius) and reindeer (Rangifer tarandus) and many arctic-alpine plant taxa, such as Dryas octopetala, Salix polaris and Saxifraga aizoides, from the region. This rapid biotic turnover rate occurred when the rate of warming was 0.17 °C/decade, thus slightly lower than the current Northern Hemisphere warming of 0.2 °C/decade. We therefore conclude that the Younger Dryas-Holocene shift with its rapid turnover rates and associated regional extinctions represents an important palaeoanalogue to the current high latitude warming and gives insights about the probable future turnover rates and patterns of the terrestrial and aquatic ecosystem change.

Profils des porteurs du VIH/SIDA au début du traitement ...

African Journals Online (AJOL)

But : Décrire les profils des porteurs de VIH/sida au début du traitement antirétroviral. Matériels et méthode: Les dossiers des porteurs du VIH/sida de la région maritime ont été analysés de mai 2008 à avril 2009 par le comité thérapeutique. Résultats: Parmi les 641 dossiers analysés, 67,40% venaient du district de Yoto.

Numerical analysis of steady state and transient analysis of high temperature ceramic plate-fin heat exchanger

International Nuclear Information System (INIS)

Nagarajan, Vijaisri; Chen, Yitung; Wang, Qiuwang; Ma, Ting

2014-01-01

Highlights: • Rip saw fin design is considered to be the best because it has thin fins and has higher heat transfer coefficient. • Minimum principal stress and maximum safety factor are obtained for the inverted bolt fin design. • Maximum principal stress and minimum safety factor are obtained for triangular fin design. • Thermal stress has significant impact than mechanical stress. • High principal stress is found at the startup and shutdown stage. - Abstract: In this study three-dimensional model of ceramic plate-fin high temperature heat exchanger with different fin designs and arrangements is analyzed numerically using ANSYS FLUENT and ANSYS structural module. The ability of ceramics to withstand high temperature and corrosion makes silicon carbide (SiC) suitable candidate material to be used in high temperature heat exchanger. The operating temperature of heat exchanger is 950 °C and the operating pressure is 1.5 MPa. The working fluids are helium, sulfur trioxide, sulfur dioxide, oxygen and the water vapor. Fluid flow and heat transfer analysis are carried out for steady and transient state in FLUENT. The obtained thermal and pressure load for the steady and transient state from ANSYS FLUENT are imported to ANSYS structural module to obtain the principal stress and the factor of safety. Different arrangements of rectangular fins, triangular fins, inverted bolt fins and ripsaw fins are studied. From the results it is found that the minimum stress and the maximum safety factor are obtained for inverted bolt fins. The triangular fins have the maximum principal stress and minimum factor of safety. However, the fluid flow and heat transfer analysis show inverted bolt fins and triangular fins produce higher pressure drop and friction factor. The steady state maximum principal stress is 10.08 MPa, 9.90 MPa and 11.43 MPa for straight, staggered and top and bottom ripsaw fin arrangement. The corresponding safety factors are 21.80, 21.95 and 19

Feasibility Study to Reduce Thermal Resistance of Finned Containment Wall in Simplified OPR1000

Energy Technology Data Exchange (ETDEWEB)

Lee, Jong Hwi; Kang, Hie Chan [Kunsan National University, Gunsan (Korea, Republic of); Noh, Hyung Gyun [Pohang University, Pohang (Korea, Republic of)

2016-05-15

This concept is securing of cooling capability by using finned containment itself, it could be another alternative for achieving decompression of containment as heat sink. The objective of this study is a feasibility test to estimate the heat transfer performance from the finned containment wall in case of OPR1000. The commercial code, ANSYS CFX 16 was used in this work. The number of grids is about 1.8 million. Therefore, 250mm rebar affects more considerable than that of 50mm to the temperature distribution. For this reasons, temperature distribution of z-axis direction was showed significant changes in (c). The heat transfer in three types of containment was 267.6W, 265.2W and 307.8W, respectively. The Type B case increased up to 15% of heat transfer than the baseline containment building. Three different types of containment wall were tested by numerical simulation to understand the cooling performance of finned containment wall. We can conclude as follows: For the finned containment wall type A that fins are installed inside and outside with the same rebar configuration of conventional containment building, the heat transfer is almost the same as conventional containment wall. The finned containment wall type B that volume fraction of rebar is increased transfer the heat 15% more compared with conventional one. The cross-sectional area or volume fraction of the rebar to attach fin is important to enhance the heat transfer. The fin efficiency of the fin is very low as 3.1% in the present cases.

Role of fin material and nanofluid in performance enhancement of automobile radiator

Science.gov (United States)

Jadar, Raju; Shashishekar, K. S.; Channa Keshava Naik, N.

2018-04-01

An effective cooling system can avoid engine and its components from overheating and helps in achieving optimum engine performance. This work deals with the fabrication and performance evaluation of an automobile radiator with i) Aluminum fins and ii) Al-MWCNT fins using 0.1 w/v% f-MWCNT nanofluid. F-MWCNT nanoparticles in the base fluid improves the rate of heat transfer in an automobile radiator integrated with Al-MWCNT fins. The enhancement of heat transfer mainly depends on the quantity of F-MWCNT nanoparticles added to the host fluid. During the study it was found that at a low weight by volume concentration of nanofluid the heat transfer enhancement of 8% was achieved using Al-MWCNT fins compared to base fluid.

Inverse analysis of a rectangular fin using the lattice Boltzmann method

International Nuclear Information System (INIS)

Bamdad, Keivan; Ashorynejad, Hamid Reza

2015-01-01

Highlights: • Lattice Boltzmann method is used to study a transient conductive-convective fin. • LBM and Conjugate Gradient Method (CGM) are used to solve an inverse problem in fins. • LBM–ACGM estimates the unknown boundary conditions of fins accurately. • The accuracy and CPU time of LBM–ACGM are compared to IFDM–ACGM. • LBM–ACGM could be a good alternative for the conventional inverse methods. - Abstract: Inverse methods have many applications in determining unknown variables in heat transfer problems when direct measurements are impossible. As most common inverse methods are iterative and time consuming especially for complex geometries, developing more efficient methods seems necessary. In this paper, a direct transient conduction–convection heat transfer problem (fin) under several boundary conditions was solved by using lattice Boltzmann method (LBM), and then the results were successfully validated against both the finite difference method and analytical solution. Then, in the inverse problem both unknown base temperatures and heat fluxes in the rectangular fin were estimated by combining the adjoint conjugate gradient method (ACGM) and LBM. A close agreement between the exact values and estimated results confirmed the validity and accuracy of the ACGM–LBM. To compare the calculation time of ACGM–LBM, the inverse problem was solved by implicit finite difference methods as well. This comparison proved that the ACGM–LBM was an accurate and fast method to determine unknown thermal boundary conditions in transient conduction–convection heat transfer problems. The findings can efficiently determine the unknown variables in fins when a desired temperature distribution is available

Utilisation du foncier agricole à des fins de culture de Jatropha dans le Bassin arachidier sénégalais: une démarche controversée et des gains pas à la hauteur des attendus du programme

Directory of Open Access Journals (Sweden)

Aminata Ndour

2017-10-01

Full Text Available Durant les années 2000, le secteur énergétique mondial a connu un tourment décisif du fait de la diminution des réserves, de la demande importante et surtout de la fluctuation des prix du pétrole. Le Sénégal, pays dépendant encore des énergies fossiles, s’est engagé dans une politique de diversification énergétique. Par conséquent, un programme biocarburant est initié. Le Bassin Arachidier est un des espaces sollicités pour l’application des politiques de promotion des biocarburants. Une zone du production agricole a accueilli une innovation énergétique. Ce fait marquant a guidé nos interrogations sur les problèmes énergétiques qui ont incité la culture de Jatropha dans le Bassin Arachidier. De façon spécifique, notre analyse de la filière Jatropha précise les stratégies déployées. Il est questions dans ce cas d’étudier les effets de Jatropha sur l’espace de production et les conditions de vie des agriculteurs, des risques de réduction des superficies de cultures traditionnelles.

Velocity Deficits in the Wake of Model Lemon Shark Dorsal Fins Measured with Particle Image Velocimetry

Science.gov (United States)

Terry, K. N.; Turner, V.; Hackett, E.

2017-12-01

Aquatic animals' morphology provides inspiration for human technological developments, as their bodies have evolved and become adapted for efficient swimming. Lemon sharks exhibit a uniquely large second dorsal fin that is nearly the same size as the first fin, the hydrodynamic role of which is unknown. This experimental study looks at the drag forces on a scale model of the Lemon shark's unique two-fin configuration in comparison to drag forces on a more typical one-fin configuration. The experiments were performed in a recirculating water flume, where the wakes behind the scale models are measured using particle image velocimetry. The experiments are performed at three different flow speeds for both fin configurations. The measured instantaneous 2D distributions of the streamwise and wall-normal velocity components are ensemble averaged to generate streamwise velocity vertical profiles. In addition, velocity deficit profiles are computed from the difference between these mean streamwise velocity profiles and the free stream velocity, which is computed based on measured flow rates during the experiments. Results show that the mean velocities behind the fin and near the fin tip are smallest and increase as the streamwise distance from the fin tip increases. The magnitude of velocity deficits increases with increasing flow speed for both fin configurations, but at all flow speeds, the two-fin configurations generate larger velocity deficits than the one-fin configurations. Because the velocity deficit is directly proportional to the drag force, these results suggest that the two-fin configuration produces more drag.

Aménager le temps de travail en fin de carrière pour inciter à rester en emploi ?

Directory of Open Access Journals (Sweden)

Diane-Gabrielle Tremblay

2012-05-01

Full Text Available Notre recherche permet de mieux comprendre les motivations et intérêts des salariés à l’égard de la fin de carrière et la retraite. Elle repose sur des entretiens en profondeur, et a permis de constater que si le départ hâtif reste une aspiration pour plusieurs, des mesures d’aménagement du temps de travail ou le temps partiel, mais aussi d’autres mesures (mentorat, mandats, projets pourraient inciter les salariés à rester plus longtemps en emploi. Il est pertinent de souligner cet intérêt pour le changement de rôle, le passage à un rôle de formateur ou de mentor, qui a été peu documenté à ce jour comme option de fin de carrière et pourrait agir comme mesure de rétention, en plus de l’aménagement du temps de travail.Ayant également interrogé les cadres de cette organisation, ils ont pu confirmer que l’aménagement et la réduction du temps de travail ainsi que les nouveaux mandats ou rôles de mentor ou de formateur n’ont pas été envisagés à ce jour dans l’organisation, ou très peu. S’ils ont été envisagés, c’est surtout dans les postes de cadres, alors que les besoins de formation de la relève se font aussi sentir dans d’autres milieux, de sorte que cela paraît constituer une avenue possible pour retenir les employés.Our research helps better understand the motivations and interests of employees with respect to late career and retirement. It is based on in-depth interviews, and while it highlights that early retirement remains an important aspiration, we found that working time arrangements and part time, but also other measures (mentoring, mandates, project assignments could encourage employees to stay longer in employment. It is pertinent to note interest in the role change, the transition to a training role or mentor, which has been rather poorly documented to date as an option and could act as a measure of retention, in addition to the working time arrangements.Having also questioned

Les perspectives du gaz naturel dans le Monde World Natural Gas Prospects

Directory of Open Access Journals (Sweden)

Valais M.

2006-11-01

Full Text Available Dans un monde en quête de diversification énergétique, le gaz naturel apparaît comme une source d'énergie particulièrement attrayante. Par son abondance, sa facilité de substitution aux produits pétroliers dans une gamme très large d'usages, il pourrait assurément jouer un rôle beaucoup plus important dans la couverture des besoins énergétiques mondiaux. Toutefois, de nombreux obstacles semblent devoir ralentir sa progression. Cet article dégage les grands paramètres techniques et économiques qui devraient conditionner le développement de l'industrie du gaz dans le monde et présente des perspectives d'évolution de sa production et de son commerce international d'ici à la fin du siècle. For a world in search of energy diversification, natural gas is a particularly attractive source. Its abundance and its facility for being substituted for petroleum products over a wide range of uses should certainly mean that it will play a much more important rote in filling world energy needs. Nonetheless, many obstacles are hindering its progress. This article outlines the leading technical and economic parameters which should influence the development of the world gas industry, and the prospects for its production and international trade evolution between now and the end of the century.

Les effets du changement climatique dans le bassin du Congo : la ...

International Development Research Centre (IDRC) Digital Library (Canada)

22 avr. 2016 ... Dans le bassin du fleuve Congo, plus de 80 % des habitants vivent exclusivement de l'agriculture, de la pêche, de l'élevage et de la cueillette, qui sont des activités largement tributaires du climat.

Two-dimensional nonlinear transient heat transfer analysis of variable section pin fins

Energy Technology Data Exchange (ETDEWEB)

Malekzadeh, P. [Department of Mechanical Engineering, School of Engineering, Persian Gulf University, Boushehr 75168 (Iran); Rahideh, H. [Department of Chemical Engineering, School of Engineering, Persian Gulf University, Boushehr 75168 (Iran)

2009-04-15

The two-dimensional nonlinear transient heat transfer analysis of variable cross section pin-fins is studied using the incremental differential quadrature method (IDQM) as a simple, accurate, and computationally efficient numerical tool. The formulations are general so that it can easily be used for arbitrary continuously varying cross section pin fins with the spatial-temperature dependent thermal parameters. On all external surfaces of the pin fin, the convective-radiative condition is considered. The effects of two different types of boundary conditions at the base of pin fin are investigated: time and spatial dependent temperature, and the convection heat transfer. The thermal conductivity of the pin fin is assumed to vary as a linear function of the temperature. The accuracy of the method is demonstrated by comparing its results with those generated by finite difference method. It is shown that using few grid points, results in excellent agreements with those of FDM are obtained. Less computational efforts of the method with respect to finite difference method is shown. (author)

A comparison of pectoral fin contact between two different wild dolphin populations

Science.gov (United States)

Dudzinski, K.M.; Gregg, J.D.; Ribic, C.A.; Kuczaj, S.A.

2009-01-01

Contact behaviour involving the pectoral fin has been documented in a number of dolphin species, and various explanations about its function have been offered. Pectoral fin contact can take a variety of forms, and involves a number of body parts and movements, likely differing depending upon social or ecological context. For this study, we compare the pectoral fin contact behaviour of two species of wild dolphins: Indo-Pacific bottlenose dolphins (Tursiops aduncus) from around Mikura Island, Japan, and Atlantic spotted dolphins (Stenella frontalis) from The Bahamas. The two study populations exhibit surprising similarity in the ways in which pectoral fin contacts are used, despite differences in species and environmental conditions at the two sites. Differences in contact rates for calves between the two sites suggest that calf-focused aggression from adult dolphins is more prevalent at Mikura than in The Bahamas. Our results suggest that pectoral fin contact behaviour seems to be driven primarily by social pressures, and may be similar in function to allogrooming described in primates. ?? 2008 Elsevier B.V.

Protective Role of Comfrey Leave Extracts on UV-induced Zebrafish Fin Damage.

Science.gov (United States)

Cheng, Chien-Chung; Chou, Chi-Yuan; Chang, Yao-Chin; Wang, Hsuan-Wen; Wen, Chi-Chung; Chen, Yau-Hung

2014-07-01

In zebrafish, UV exposure leads to fin malformation phenotypes including fin reduction or absence. The present study evaluated UV-protective activities of comfrey leaves extracts in a zebrafish model by recording fin morphological changes. Chemopreventive effects of comfrey leave extracts were evaluated using Kaplan-Meier analysis and Cox proportional hazards regression. The results showed that (1) the mean times of return to normal fin in the UV+comfrey (50 and 100 ppm) groups were 3.43 and 2.86 days and were quicker compared with that in the UV only group (4.21 days); (2) zebrafish fins in the UV+comfrey (50 and 100 ppm) groups were 2.05 and 3.25 times more likely to return to normal than those in the UV only group; and (3) comfrey leave extracts had UV-absorbance abilities and significantly reduced ROS production in UV-exposed zebrafish embryos, which may attenuate UV-mediated apoptosis. In conclusion, comfrey leaves extracts may have the potential to be developed as UV-protective agents to protect zebrafish embryos from UV-induced damage.

3-D NUMERICAL STUDY AND COMPARISON OF ECCENTRIC AND CONCENTRIC ANNULAR-FINNED TUBE HEAT EXCHANGERS

Directory of Open Access Journals (Sweden)

FAROUK TAHROUR

2015-11-01

Full Text Available The use of 3-D computational fluid dynamics (CFD is proposed to simulate the conjugate conduction-convection of heat transfer problems in eccentric annularfinned tube heat exchangers. The numerical simulation results allow us to evaluate the heat transfer coefficient over fin surfaces, the fin efficiency and the pressure drop. The aim of the present paper is to determine the optimum tube position in the circular fin that maximizes heat dissipation and minimizes pressure drop. In addition, this study analyzes the effects of fin spacing and fin tube diameter on heat transfer and flow characteristics for a range of Reynolds numbers, 4500≤Re≤22500. A satisfactory qualitative and quantitative agreement was obtained between the numerical predictions and the results published in the literature. For small fin spacings, the eccentric annular finned tube is more efficient than the concentric one. Among the cases examined, the average heat transfer coefficient of the eccentric annular-finned tube, for a tube shift St =12 mm and a Reynolds number Re = 9923, was 7.61% greater than that of the concentric one. This gain is associated with a 43.09% reduction in pressure drop.

Flexible nanoscale high-performance FinFETs

KAUST Repository

Sevilla, Galo T.; Ghoneim, Mohamed T.; Fahad, Hossain M.; Rojas, Jhonathan Prieto; Hussain, Aftab M.; Hussain, Muhammad Mustafa

2014-01-01

With the emergence of the Internet of Things (IoT), flexible high-performance nanoscale electronics are more desired. At the moment, FinFET is the most advanced transistor architecture used in the state-of-the-art microprocessors. Therefore, we show

Latest Pleistocene and Holocene Glacier Fluctuations in southernmost Patagonia

Science.gov (United States)

Menounos, B.; Maurer, M.; Clague, J. J.; osborn, G.; Ponce, F.; Davis, P. T.; Rabassa, J.; Coronato, A.; Marr, R.

2011-12-01

Summer insolation has been proposed to explain long-term glacier fluctuations during the Holocene. If correct, the record of glacier fluctuations at high latitudes in the Southern Hemisphere should differ from that in the Northern Hemisphere. Testing this insolation hypothesis has been hampered by dating uncertainties of many Holocene glacier chronologies from Patagonia. We report on our ongoing research aimed at developing a regional glacier chronology at the southern end of the Andes north and west of Ushuaia, Argentina. We have found evidence for an advance of cirque glaciers at the end of the Pleistocene; one or locally two closely spaced moraines extend up to 2 km beyond Little Ice Age moraines. Radiocarbon dating of terrestrial macrofossils recovered from basal sediments behind two of these moraines yielded ages of 10,320 ± 25 and 10,330 ± 30 14C yr BP. These moraines may record glacier advances coeval with the Antarctic Cold Reversal; surface exposure dating of these moraines is currently in progress to test this hypothesis. We find no evidence of Holocene moraines older than 6800 14C yr BP, based on the distribution of Hudson tephra of that age. At some sites, there is evidence for an early Neoglacial advance of glaciers slightly beyond (Peru. We have documented multiple wood mats with stumps in growth position separated by till units in a 100 m section of the northeast lateral moraine at Stoppani Glacier (54.78 S, 68.98 W), 50 km west of Ushuaia. Ten radiocarbon ages on these wood mats range in age from 3510 ± 15 to 135 ± 15 14C yr BP. The mats decrease in age up-section; many overlap with published age ranges for Neoglacial advances in western Canada. Taken together, these data: a) do not support the summer insolation hypothesis for Holocene glacier fluctuations in southernmost Patagonia; b) confirm paleobotanical evidence for a warm, dry early Holocene; and c) suggest that many Neoglacial advances in southernmost Patagonia and western North America

Timing and magnitude of the Caribbean mid-Holocene highstand

Science.gov (United States)

Ashe, E.; Khan, N.; Horton, B.; Brocard, G. Y.; Dutton, A.; Engelhart, S. E.; Kopp, R. E.; Hill, D. F.; Peltier, W. R.; Scatena, F. N.

2015-12-01

We present a database of published and new relative sea-level (RSL) data for the past 13 ka, which constrains the Holocene sea-level histories of the Caribbean coast of Central and South America (Florida Keys, USA to Guyana) and the Bahamas and Greater and Lesser Antilles islands. Our evaluation of mangrove peat and Acropora palmata sea-level indicators from geological investigations provides 503 sea-level index points and 242 limiting dates. We subdivide the database into 21 regions based on the availability of data, tectonic setting, and distance from the former Laurentide ice sheet. Most index points (75%) and limiting dates (90%) are <8 ka, although there is an unusual temporal distribution with the greatest amount of the data (~28%) occurring between 6-8 ka. We reassess and screen radiocarbon and U/Th ages of mangrove peat and coral data. We use the stratigraphic position (overburden thickness) of index points account for sediment compaction, and use the paleotidal model of Hill et al. (2011) to account for Holocene changes in paleotidal range. A noisy-input Gaussian process regression model calculates that the rates of RSL change were highest during the early Holocene (3-8 mm/yr) and have decreased over time (< 2 mm/yr), which is related to the reduction of ice equivalent meltwater input and collapse of the proglacial forebulge during the Holocene. The sea-level reconstructions demonstrate that RSL did not exceed the present height (0 m) during the Holocene in the majority of locations, with the exception of a small highstand (<2 m) on the northern coast of South America along the Orinoco Delta and Suriname/Guyana located furthest away from the former Laurentide Ice Sheet. The different sea-level histories are an ongoing isostatic response to deglaciation of the Laurentide Ice Sheet and suggest subsidence resulting from collapse of the proglacial forebulge reaches further south than previously considered.

Numerical Study of Compact Plate-Fin Heat Exchanger for Rotary-Vane Gas Refrigeration Machine

Directory of Open Access Journals (Sweden)

V. V. Trandafilov

2017-10-01

Full Text Available Plate-fin heat exchangers are widely used in refrigeration technique. They are popular because of their compactness and excellent heat transfer performance. Here we present a numerical model for the development, research and optimization of a plate-fin heat exchanger for a rotary-vane gas refrigeration machine. The method of analysis by graphic method of plate - fin heat exchanger is proposed. The model describes the effects of secondary parameters such as axial thermal conductivity through a metal matrix of the heat exchanger. The influence of geometric parameters and heat transfer coefficient is studied. Graphs of dependences of length, efficiency of a fin and pressure drop in a heat exchanger on the thickness of the fin and the number of fins per meter are obtained. To analyze the results of numerical simulation, the heat exchanger was designed in the Aspen HYSYS program. The simulation results show that the total deviation from the proposed numerical model is not more than 15%. 

(Sorghum bicolor (L.) Moench) du Nord du Burkina Faso

African Journals Online (AJOL)

SARAH

29 déc. 2014 ... sorghos à grains sucrés ont un cycle court et arrivent donc à maturité avant les autres sorghos et le mil d'où leur exploitation comme aliment de soudure par les paysans. L'organisation de la diversité morphologique des accessions de sorghos à grains sucrés du Nord du. Burkina autour principalement des ...

Millennial Scale Variability of the AMOC and its Link to Climate During the Holocene

Science.gov (United States)

Thornalley, D. J.; Oppo, D.; Keigwin, L. D.; Hall, I. R.; Moffa Sanchez, P.

2014-12-01

Several proxy and modelling studies suggest that there may have been considerable change in the operation the Atlantic Meridional Overturning Circulation (AMOC) during the Holocene. Yet despite its importance for regional and global climate, the Holocene history of the AMOC is poorly constrained. Improving our knowledge of past AMOC variability will contribute to our general understanding of the dynamics of ocean circulation and the role it may play in causing or amplifying climate variability on millennial timescales. We present Holocene grain-size records in depth transects from Blake Outer Ridge and Cape Hatteras, sampling the full-depth range of the Deep Western Boundary Current (DWBC), the lower limb of the AMOC. These records will complement a depth-transect of grain-size records sampling the Iceland-Scotland (I-S) overflow, showing Holocene variations that reflect deglacial meltwater forcing in the early Holocene and insolation-forced trends from the middle-to-late Holocene (Thornalley et al., 2013, Climate of the Past). We will also present detailed grain-size records for the last 2,000 years, both in a depth transect of cores off Cape Hatteras, and from cores in the Iceland Basin, sampling the I-S overflow. Our extensive datasets enable us to provide a coherent synthesis of changes in the flow strength of key components of the AMOC on centennial-millennial and orbital timescales, which we can use to develop our understanding of past millennial-scale climate variability. Specific questions to be addressed include: How well coupled are Holocene trends in Iceland-Scotland overflow and the DWBC? How did I-S overflow and the AMOC vary during the last millennia, including the last ~150 years since the end of the Little Ice Age? Initial results suggest a long-term anti-phasing of the Nordic overflows, wherein mid-late Holocene weakening of the I-S overflow has been compensated for by a strengthening of Denmark Strait overflow. We will also report on pronounced

Holocene volcanic geology, volcanic hazard, and risk on Taveuni, Fiji

International Nuclear Information System (INIS)

Cronin, S.J.; Neall, V.E.

2001-01-01

The Holocene volcanic geology of Taveuni has been mapped in order to produce a volcanic hazard and risk assessment for the island. Taveuni is the third-largest island of the Fiji group and home to 14,500 people. At least cubic km 2.7 of olivine-alkali-basalt magma was erupted from over 100 events throughout the Holocene. Vents are concentrated along a northeast-striking rift zone that is parallel to other regional structural trends. There is an overall trend of younging southward along the rift. Holocene lavas and tephras are grouped within six newly defined eruptive periods, established on a basis of radiocarbon dating. Within these periods, 14 tephra layers, useful as local marker horizons, are recognised. At least 58% of Holocene eruptions produced lava flows, while almost all produced some tephra. Individual eruption event volumes ranged between 0.001 and cubic km 0.20 (dense rock equivalent). Many eruptions involved at least some phases of phreatic and/or phreato-magmatic activity, although dominant hydrovolcanic activity was limited to only a few events. A volcanic hazard map is presented, based on the Holocene geology map and statistical analyses of eruption recurrence. The highest levels of ground-based and near-vent hazards are concentrated along the southern portion of the island's rift axis, with the paths of initial lava flows predicted from present topography. Tephra fall hazards are based on eruption parameters interpreted from mapped Holocene tephra layers. Hawaiian explosive-style eruptions appear to be a dominant eruptive process, with prevailing low-level (<3 km) southeasterly winds dispersing most tephra to the northwestern quadrant. Vulnerable elements (population centres, infrastructure, and economy) on Taveuni have been considered in deriving a volcanic risk assessment for the island. A number of infrastructural and subdivision developments are either under way or planned for the island, driven by its highly fertile soils and availability of

Timing, cause and consequences of mid-Holocene climate transition in the Arabian Sea

Digital Repository Service at National Institute of Oceanography (India)

Saraswat, R.; Naik, Dinesh K.; Nigam, R.; Gaur, A.S.

-50,000 years cal BP. Radiocarbon 51, 1111-1150. Roberts, N., Brayshaw, D., Kuzucuoglu, C., Perez, R., Sadori, L., 2011. The mid-Holocene climatic transition in the Mediterranean: Causes and consequences. The Holocene 21, 3-13. Ruddiman, W.F., Ellis, E...

Etude de la transition ferroelectrique-ferroelastique du KD2PO4 forme du front de phase en fonction du gradient thermique

OpenAIRE

Kvítek, Zdeněk

2010-01-01

Etude de la transition ferroelectrique-ferroelastique du KD2PO4 forme du front de phase en fonction du gradient thermique The thesis explores complex process of first order transition of KD2PO4 crystal from tetragonal phase to ferroelectric - ferroelastic orthorhombic phase and back at temperature 209 K. The experimental set up of nitrogeneous cryostat allowes temperature and temperature gradient variations during simultaneous three axes optical sample observations, dielectric measurements. T...

Optimization analysis of convective–radiative longitudinal fins with temperature-dependent properties and different section shapes and materials

International Nuclear Information System (INIS)

Mosayebidorcheh, S.; Hatami, M.; Mosayebidorcheh, T.; Ganji, D.D.

2015-01-01

Graphical abstract: Temperature distribution along the fins obtained for different material and section shapes. - Highlights: • The steady state thermal analysis of longitudinal fins is presented. • The properties of fins are assumed as a function of temperature. • The rectangular, convex, triangular and concave profiles are considered for fin shape. • Least Square Method (LSM) is used for solving the governing equation. • Thermal optimization of fin geometry is presented based on maximum value of heat transfer. - Abstract: The main aim of this study is to obtain an optimum design point for fin geometry, so that heat transfer rate reaches to a maximum value in a constant fin volume. Effect of fin thicknesses ratio (τ), convection coefficient power index (m), profile power parameter (n), base thickness (δ) and fin material are evaluated in the fin optimization point for heat transfer rate, effectiveness and efficiency. It’s assumed that the thickness of longitudinal fins varies with length in a special profile, so four different shapes (rectangular, convex, triangular and concave) are considered. In present study, temperature-dependent heat generation, convection and radiation are considered and an analytical technique based on the least square method is proposed for the solution methodology. Results show that by increasing the fin thicknesses ratio, maximum heat transfer rate decreases and Copper among the other materials has the most heat transfer rate in a constant volume.

Swimming performance of a bio-inspired robotic vessel with undulating fin propulsion.

Science.gov (United States)

Liu, Hanlin; Curet, Oscar M

2018-06-18

Undulatory fin propulsion exhibits high degree of maneuver control -- an ideal for underwater vessels exploring complex environments. In this work, we developed and tested a self-contained, free-swimming robot with a single undulating fin running along the length of the robot, which controls both forward motion and directional maneuvers. We successfully replicated several maneuvers including forward swimming, reversed motion, diving, station-keeping and vertical swimming. For each maneuver, a series of experiments were performed as a function of fin frequency, wavelength and traveling wave direction to measure swimming velocities, orientation angles and mean power consumption. In addition, three-dimensional flow fields were measured during forward swimming and station-keeping using volumetric particle image velocimetry (PIV). The efficiency for forward swimming was compared using three metrics: cost of transport, wave efficiency and Strouhal number. The results indicate that the cost of transport exhibits a V-shape trend with the minimum value at low swimming velocity. The robot can reach optimal wave efficiency and locomotor performance at a range of 0.2 to 0.4 St. Volumetric PIV data reveal the shed of vortex tubes generated by the fin during forward swimming and station keeping. For forward swimming, a series of vortex tubes are shed off the fin edge with a lateral and downward direction with respect to the longitudinal axis of the fin. For station keeping, flow measurements suggest that the vortex tubes are shed at the mid-section of the fin while the posterior and anterior segment of the vortex stay attached to the fin. These results agree with the previous vortex structures based on simulations and 2D PIV. The further development of this vessel with high maneuverability and station keeping performance can be used for oceanography, coastal exploration, defense, oil industry and other marine industries where operations are unsafe or impractical for divers or

Les Cahiers du CREAD

African Journals Online (AJOL)

Admin

politique de bas prix exercée par la Russie et le Qatar vient confirmer ce constat ; s'ajoute à cela l'entrée éventuelle du gaz non conven- tionnel, dont son prix actuel de 3/4 $US, offre aux USA l'opportunité d'être exportateur de ..... les compagnies à produire en matière du gaz naturel, tels le prix du gaz naturel, le prix des ...

The stress characteristics of plate-fin structures at the different operation parameters of LNG heat exchanger

Directory of Open Access Journals (Sweden)

Ma Hongqiang

2018-01-01

Full Text Available In this paper, the stresses of plate-fin structures at the different operation parameters were analyzed in actual operation process of LNG plate-fin heat exchanger based on finite element method and thermal elastic theory. Stress characteristics of plate-fin structures were investigated at the different operation parameters of that. The results show that the structural failure of plate-fin structures is mainly induced by the maximum shear stress at the brazing filler metal layer between plate and fin while by the maximum normal stress in the region of brazed joint near the fin side. And a crack would initiate in brazed joint near the fin side. The maximum normal stress is also main factor to result in the structural failure of plate-fin structures at the different temperature difference (between Natural Gas (NG and Mixture Refrigerant (MR, MR temperature and NG pressure of LNG heat exchanger. At the same time, the peak stresses obviously increase as the temperature difference, MR temperature and NG pressure increase. These results will provide some constructive instructions in the safe operation of LNG plate-fin heat exchanger in a large-scale LNG cold-box.

Holocene aeolian activity in the Dinggye area (Southern Tibet, China)

Science.gov (United States)

Pan, Meihui; Wu, Yongqiu; Zheng, Yinghua; Tan, Lihua

2014-03-01

The Dinggye area (Southern Tibet) contains numerous aeolian sediments, including modern and ancient aeolian sand deposition. In this study, we determined the chronological sequences of several profiles of Holocene paleo-aeolian deposits using Optically Stimulate Luminescence (OSL) and radiocarbon (Accelerator Mass Spectrometry (AMS) 14C and conventional 14C) dating. Using the grain size, magnetic susceptibility, organic content and chrome characteristics of the deposits, we reconstructed the Holocene aeolian processes in the Dinggye area. The results from the paleo-aeolian depositional record indicate multiple changes in the intensity of aeolian activity and soil fixing with alternations between cool-dry and warm-humid climate conditions in the Dinggye area during the Holocene. From 12.8 ka B.P. to the present, the climate has fluctuated frequently. From 12.8 to 11.6 ka B.P. and from 9.3 to 4.9 ka B.P., the climate was warm and humid with weak aeolian activity, and a sandy paleosol developed. The peak Holocene megathermal period and the main period of pedogenesis in the study area was from 6.6 to 4.9 ka B.P. Between 11.6 and 9.3 ka B.P. and since 2.0 ka B.P., the sandlot expanded due to a cool, dry and windy climate; aeolian activity was strong and caused the development of moving dunes. The period between 4.9 and 2.0 ka B.P. was relatively cool and dry with slightly strengthened aeolian activity that developed stationary and semi-stationary dunes. In general, the Holocene events recorded by the paleo-aeolian deposits correspond well with those interpreted by other methods, such as records from ice-cores, lacustrine deposits and tree rings, but there are minor discrepancies between the methods.

Holocene Climate Variability on the Centennial and Millennial Time Scale

Directory of Open Access Journals (Sweden)

Eun Hee Lee

2014-12-01

Full Text Available There have been many suggestions and much debate about climate variability during the Holocene. However, their complex forcing factors and mechanisms have not yet been clearly identified. In this paper, we have examined the Holocene climate cycles and features based on the wavelet analyses of 14C, 10Be, and 18O records. The wavelet results of the 14C and 10Be data show that the cycles of ~2180-2310, ~970, ~500-520, ~350-360, and ~210-220 years are dominant, and the ~1720 and ~1500 year cycles are relatively weak and subdominant. In particular, the ~2180-2310 year periodicity corresponding to the Hallstatt cycle is constantly significant throughout the Holocene, while the ~970 year cycle corresponding to the Eddy cycle is mainly prominent in the early half of the Holocene. In addition, distinctive signals of the ~210-220 year period corresponding to the de Vries cycle appear recurrently in the wavelet distribution of 14C and 10Be, which coincide with the grand solar minima periods. These de Vries cycle events occurred every ~2270 years on average, implying a connection with the Hallstatt cycle. In contrast, the wavelet results of 18O data show that the cycles of ~1900-2000, ~900-1000, and ~550-560 years are dominant, while the ~2750 and ~2500 year cycles are subdominant. The periods of ~2750, ~2500, and ~1900 years being derived from the 18O records of NGRIP, GRIP and GISP2 ice cores, respectively, are rather longer or shorter than the Hallstatt cycle derived from the 14C and 10Be records. The records of these three sites all show the ~900-1000 year periodicity corresponding to the Eddy cycle in the early half of the Holocene.

Experimental research on single phase convection heat transfer in micro-fin tube

International Nuclear Information System (INIS)

Fan Guangming; Sun Zhongning; Zhu Sheng

2011-01-01

An experimental investigation of heat transfer and flow resistance characteristics of single phase water in three micro-fin tubes with different fin height was conducted. At the same time, the efficiency of micro-fin tubes within the experimental scope was evaluated and the optimal working region was determined. Based on the experimental data in the optimal working region, correlations for predicting the heat transfer and flow resistance were also given by multiple regression method. The result indicates that the micro-fin tubes can greatly enhance the single-phase heat transfer in turbulent flow, and the increase of heat transfer coefficient is higher than the increase of flow resistance. The accuracy of the correlation is very high, of which the deviation from the experimental value is very small. (authors)

Introduction

OpenAIRE

G. Garsoïan, Nina

2015-01-01

Le contact immédiat du monde arménien et de Rome, qui se connaissaient déjà de longue date, se place vers la fin de l’ère préchrétienne avec l’absorption romaine du royaume cis-euphratésien de Petite Arménie en même temps que celui du Pont, dont il semble avoir fait partie à l’époque de Mithridate. Devenue province sous Vespasien, comme partie de la Cappadoce, la Petite Arménie ne retrouva son identité, sous la forme d’une province séparée de ce nom, que sous Dioclétien à la fin du troisième ...

Glaciation in the Andes during the Lateglacial and Holocene

Science.gov (United States)

Rodbell, Donald T.; Smith, Jacqueline A.; Mark, Bryan G.

2009-10-01

This review updates the chronology of Andean glaciation during the Lateglacial and the Holocene from the numerous articles and reviews published over the past three decades. The Andes, which include some of the world's wettest and driest mountainous regions, offer an unparalleled opportunity to elucidate spatial and temporal patterns of glaciation along a continuous 68-degree meridional transect. The geographic and altitudinal extent of modern glaciers and the sensitivity of both modern and former glaciers to respond to changes in specific climatic variables reflect broad-scale atmospheric circulation and consequent regional moisture patterns. Glaciers in the tropical Andes and in the mid-latitude Andes are likely to have been far more sensitive to changes in temperature than glaciers in the dry subtropical Andes. Broad-scale temporal and spatial patterns of glaciation during the Lateglacial are apparent. In the southernmost Andes, the Lateglacial chronology appears to have a strong Antarctic signature with the best-dated moraines correlating closely with the Antarctic Cold Reversal. The southernmost Andes do not appear to have experienced a significant ice advance coeval with the Younger Dryas (YD) climatic reversal. At the other end of the Andes, from ˜0 to 9°N, a stronger YD connection may exist, but critical stratigraphic and geochronologic work is required before a YD ice advance can be fully demonstrated. In the central Andes of Peru, well-dated moraines record a significant ice readvance at the onset of the YD, but ice was retreating during much of the remaining YD interval. The spatial-temporal pattern of Holocene glaciation exhibits tantalizing but incomplete evidence for an Early to Mid-Holocene ice advance(s) in many regions, but not in the arid subtropical Andes, where moraines deposited during or slightly prior to the Little Ice Age (LIA) record the most extensive advance of the Holocene. In many regions, there is strong evidence for Neoglacial

Assessment of in vitro antifungal activity of preparation ''fin Candimis'' against Candida strains

Directory of Open Access Journals (Sweden)

Anna Głowacka

2013-12-01

Full Text Available The aim of the study was to assess the antifungal activity of preparation „fin Candimis” (oregano essential oil against yeast-like strains belonging to the genus Candida. During the investigation, there were used up nine Candida albicans strains and ten C. glabrata strains isolated from different clinical material, along with one C. albicans demonstration strain ATCC 90028. The oregano essential oil, utilized in the study, was obtained from fresh leaves of Origanum vulgare L. and bore a trade name „fin Candimis”. According to data yielded by its manufacturer, concentration of pure oregano essential oil in preparation „fin Candimis” totals up to 210 mg/ml. The susceptibility of the Candida strains to preparation „fin Candimis” was assessed by means of the disc-diffusion method, upon the Sabouraud solid medium (after a 24-hour incubation of the cultures at temperature of 37 degrees centigrade; the oregano essential oil had been diluted in 1 ml of DMSO, according to the geometrical progression. A measure of the antifungal activity of preparation „fin Candimis” was the minimal inhibitory concentration (MIC, in terms of the fungus growth. Preparation „fin Candimis” is capable of being applied in the prevention and treatment of candidiasis – alone, or as a natural adjunctive agent. The C. albicans strains are more susceptible to preparation „fin Candimis” in comparison to the C. glabrata ones.

Thermal management of electronics using phase change material based pin fin heat sinks

International Nuclear Information System (INIS)

Baby, R; Balaji, C

2012-01-01

This paper reports the results of an experimental study carried out to explore the thermal characteristics of phase change material based heat sinks for electronic equipment cooling. The phase change material (PCM) used in this study is n – eicosane. All heat sinks used in the present study are made of aluminium with dimensions of 80 × 62 mm 2 base with a height of 25 mm. Pin fins acts as the thermal conductivity enhancer (TCE) to improve the distribution of heat more uniformly as the thermal conductivity of the PCM is very low. A total of three different pin fin heat sink geometries with 33, 72 and 120 pin fins filled with phase change materials giving rise to 4%, 9% and 15% volume fractions of the TCE respectively were experimentally investigated. Baseline comparisons are done with a heat sink filled with PCM, without any fin. Studies are conducted for heat sinks on which a uniform heat load is applied at the bottom for the finned and unfinned cases. The effect of pin fins of different volume fractions with power levels ranging from 4 to 8 W corresponding to a heat flux range of 1. 59 to 3.17 kW/m 2 , was explored in this paper. The volume fraction of the PCM (PCM volume / (Total volume – fin volume)) is also varied as 0. 3, 0.6 and 1 to determine the effect of PCM volume on the overall performance of the electronic equipment.

Le mélèze en Région wallonne. Etat des lieux et stations potentielles

OpenAIRE

Claessens, Hugues; Lecomte, H.; Pauwels, D.

2002-01-01

Le mélèze a été introduit en Belgique dans la deuxième moitié du XVIIIe siècle. Il s’agissait alors du mélèze d’Europe, surtout implanté à des fins esthétiques ou d’enrichissement de forêts feuillues. Quant au mélèze du Japon, il a été importé en Europe à la fin du XIXe siècle. Ce n’est qu’à partir des années ’50 que les mélèzes ont eu du succès auprès des sylviculteurs. Ils l’ont planté le plus souvent par parquets purs après d’autres résineux ou en transformation de peuplements feuillus de ...

L'action du CRDI — le développement du secteur privé

International Development Research Centre (IDRC) Digital Library (Canada)

Cathy Egan

Le CRDI est du nombre. Il reconnaît depuis longtemps la valeur de l'industrie, des échanges et du commerce comme moteurs de la croissance économique. Grâce au soutien concret qu'il a accordé au développement du secteur privé, le CRDI a appris que deux types d'aide peuvent porter fruit : améliorer le con- texte dans ...

Burnout in the boiling of water and freon-113 on tubes with annular fins

International Nuclear Information System (INIS)

Rubin, I.R.; Pul'kin, I.N.; Roizen, L.I.

1986-01-01

This paper presents the results of numerical calculations of burnout heat flux associated with the boiling of Freon-113 and water on an annular fin of constant thickness which have been approximated by simple analytical relations. These are used to calculate the critical burnout parameters of tubes with an annular fin assembly. The calculated data may be used for the analysis of tubes with an annular fin assembly over a wide range of variation of the thermophysical properties of the material and geometrical parameters of the fin assembly

Influence of the degree of thermal contact in fin and tube heat exchanger

DEFF Research Database (Denmark)

Singh, Shobhana; Sørensen, Kim; Condra, Thomas Joseph

2016-01-01

Present work aims to investigate the significance of thermal contact area between fins and tubes in a heat exchanger. The heat exchanger type selected for the study is a liquid-gas fin and tube heat exchanger. Four different cases namely I, II, III, and IV, based on a variable degree of thermal...... contact between fins and tubes are investigated. Case-I with 100% thermal contact area between the fin and tube is set as a reference to cases-II, III, and IV with a thermal contact area of approximately 70%, 50%, and 35%, respectively. Three-dimensional (3D) steady-state numerical models based on finite...... and to compare the performance of heat exchanger design in different cases. Comparative analysis indicates a significant influence of the degree of the thermal contact area between fin and tube on the overall performance. Case-I is found to have higher overall heat transfer coefficient of 47.332 W/(m2 K), higher...

Experimental Study on Cooling Heat Transfer of Supercritical Carbon Dioxide Inside Horizontal Micro-Fin Tubes

Science.gov (United States)

Kuwahara, Ken; Higashiiu, Shinya; Ito, Daisuke; Koyama, Shigeru

This paper deals with the experimental study on cooling heat transfer of supercritical carbon dioxide inside micro-fin tubes. The geometrical parameters in micro-fin tubes used in the present study are 6.02 mm in outer diameter, 4.76 mm to 5.11 mm in average inner diameter, 0.15 mm to 0.24 mm in fin height, 5 to 25 in helix angle, 46 to 52 in number of fins and 1.4 to 2.3 in area expansion ratio. Heat transfer coefficients were measured at 8-10 MPa in pressure, 360-690 kg/(m2•s) in mass velocity and 20-75 °C in CO2 temperature. The measured heat transfer coefficients of micro-fin tubes were 1.4 to 2 times higher than those of the smooth tube having 4.42 in inner diameter. The predicted heat transfer coefficients using the correlation equation, which was developed for single-phase turbulent fluid flow inside micro-fin-tubes, showed large deviations to the measured values. The new correlation to predict cooling heat transfer coefficient of supercritical carbon dioxide inside micro-fin tubes was developed taking into account the shape of fins based on experimental data empirically. This correlation equation agreed within ±20% of almost all of the experimental data.

La mosquée et le cimetière. Espaces du sacré et pouvoir symbolique à Constantine en 1936

OpenAIRE

McDougall, James

2013-01-01

Cet essai propose une lecture de la signification d’un moment et d’un espace, vers la fin des années trente à Constantine. Deux épisodes d’affrontement entre acteurs de la société constantinoise autour du rassemblement de la communauté lors d’événements religieux (le retour des pèlerins, fêté à la Grande mosquée en avril 1936, et la zarda dite ‘de Sidi Aty’, célébrée en octobre dans le cimetière de la ville), rendent visible un ensemble d’enjeux et de conflits au sein de la société citadine à...

Les déterminants du chômage en Algérie : une analyse économétrique (1980-2009)

OpenAIRE

BOURICHE, Lahcène

2013-01-01

Cette étude montre l’existence une relation de cointégration au sens d’Engel et Granger, entre le taux de chômage et certaines variables d’ordre économiques et financières liées aux réformes économiques engagées en Algérie depuis la fin des années 80. Ces variables sont entre autres, les dépenses nationales brutes, le taux d’inflation, le taux de change et les termes de l’échange. Toutefois, il ressort de l’étude, que le taux de chômage en Algérie n’est pas corrélé avec la productivité du tra...

Small Tails Tell Tall Tales--Intra-Individual Variation in the Stable Isotope Values of Fish Fin.

Directory of Open Access Journals (Sweden)

Brian Hayden

Full Text Available Fish fin is a widely used, non-lethal sample material in studies using stable isotopes to assess the ecology of fishes. However, fish fin is composed of two distinct tissues (ray and membrane which may have different stable isotope values and are not homogeneously distributed within a fin. As such, estimates of the stable isotope values of a fish may vary according to the section of fin sampled.To assess the magnitude of this variation, we analysed carbon (δ13C, nitrogen (δ15N, hydrogen (δ2H and oxygen (δ18O stable isotopes of caudal fin from juvenile, riverine stages of Atlantic salmon (Salmo salar and brown trout (Salmo trutta. Individual fins were sub-sectioned into tip, mid and base, of which a further subset were divided into ray and membrane.Isotope variation between fin sections, evident in all four elements, was primarily related to differences between ray and membrane. Base sections were13C depleted relative to tip (~1‰ with equivalent variation evident between ray and membrane. A similar trend was evident in δ2H, though the degree of variation was far greater (~10‰. Base and ray sections were 18O enriched (~2‰ relative to tip and membrane, respectively. Ray and membrane sections displayed longitudinal variation in 15N mirroring that of composite fin (~1‰, indicating that variation in15N values was likely related to ontogenetic variation.To account for the effects of intra-fin variability in stable isotope analyses we suggest that researchers sampling fish fin, in increasing priority, 1 also analyse muscle (or liver tissue from a subsample of fish to calibrate their data, or 2 standardize sampling by selecting tissue only from the extreme tip of a fin, or 3 homogenize fins prior to analysis.

Development of plate-fin heat exchanger for intermediate heat exchanger of high-temperature gas cooled reactor. Fabrication process, high-temperature strength and creep-fatigue life prediction of plate-fin structure made of Hastelloy X

International Nuclear Information System (INIS)

Mizokami, Yorikata; Igari, Toshihide; Nakashima, Keiichi; Kawashima, Fumiko; Sakakibara, Noriyuki; Kishikawa, Ryouji; Tanihira, Masanori

2010-01-01

The helium/helium heat exchanger (i.e., intermediate heat exchanger: IHX) of a high-temperature gas-cooled reactor (HTGR) system with nuclear heat applications is installed between a primary system and a secondary system. IHX is operated at the highest temperature of 950degC and has a high capacity of up to 600 MWt. A plate-fin-type heat exchanger is the most suitable for IHX to improve construction cost. The purpose of this study is to develop an ultrafine plate-fin-type heat exchanger with a finer pitch fin than a conventional technology. In the first step, fabrication conditions of the ultrafine plate fin were optimized by press tests. In the second step, a brazing material was selected from several candidates through brazing tests of rods, and brazing conditions were optimized for plate-fin structures. In the third step, tensile strength, creep rupture, fatigue, and creep-fatigue tests were performed as typical strength tests for plate-fin structures. The obtained data were compared with those of the base metal and plate-fin element fabricated from SUS316. Finally, the accuracy of the creep-fatigue life prediction using both the linear cumulative damage rule and the equivalent homogeneous solid method was confirmed through the evaluation of creep-fatigue test results of plate-fin structures. (author)

Un établissement rural gallo-romain à Gellainville " Le Radray " (Eure-et-Loir (fin du Ier s. av. J.-C.-fin du IVe s. ap. J.-C. The development of a Gallo-Roman rural settlement over four centuries at Gellainville "Le Radray" (Eure et Loir, France (end of the 1st century BC - end of the 4th century AC

Directory of Open Access Journals (Sweden)

Hervé Delhoofs

2011-01-01

Full Text Available Le site du " Radray " sur la commune de Gellainville (28 a été fouillé en 2007. L’article présente les principaux résultats de la partie gallo-romaine du site. L’occupation se met en place à partir de la première moitié du Ier s. de notre ère. Dès les dernières décennies avant notre ère s’organise un réseau parcellaire et s’établissent les premiers bâtiments. À partir du milieu du Ier s., l’exploitation agricole se répartit selon deux ensembles : à l’est, la partie résidentielle et les dépendances, à l’ouest, la partie agricole et les bâtiments d’exploitation. L’établissement est abandonné au cours du IIIe s. Les structures du Bas-Empire ne tiennent plus compte des limites précédentes. L’occupation est matérialisée par quelques bâtiments et mares disposés à l’intérieur et en bordure d’un enclos trapézoïdal. Un petit groupe de greniers aériens est installé à l’écart, au sud-ouest. L’abandon systématique des structures d’habitation à partir de 375 ap. J.-C. montre une transformation globale de l’espace.Abstract: The site of "Radray" in the municipality of Gellainville (28 has been excavated in 2007. The article presents the main results of the Gallo-Roman part of the site. The occupation begins from the first half of the first century A.D. During the augustean period, a "parcellaire" system gets organized and the first buildings are established. Since the middle of the first century, the space is organized for the setting up of a rural settlement. On both sides of a rural path, the farming is distribued in two groups: eastwards the residential part and the outbuildings, westwards the agricultural part and the farming buildings. The settlement is abandoned during the third century. The structures of the late antiquity do not follow the former limits. The occupation is materialized by four pouds and some buildings disposed inside und south of a trapezoïdal enclosure

Understanding Fish Linear Acceleration Using an Undulatory Biorobotic Model with Soft Fluidic Elastomer Actuated Morphing Median Fins.

Science.gov (United States)

Wen, Li; Ren, Ziyu; Di Santo, Valentina; Hu, Kainan; Yuan, Tao; Wang, Tianmiao; Lauder, George V

2018-04-10

Although linear accelerations are an important common component of the diversity of fish locomotor behaviors, acceleration is one of the least-understood aspects of propulsion. Analysis of acceleration behavior in fishes with both spiny and soft-rayed median fins demonstrates that fin area is actively modulated when fish accelerate. We implemented an undulatory biomimetic robotic fish model with median fins manufactured using multimaterial three-dimensional printing-a spiny-rayed dorsal fin, soft-rayed dorsal/anal fins, and a caudal fin-whose stiffnesses span three orders of magnitude. We used an array of fluidic elastomeric soft actuators to mimic the dorsal/anal inclinator and erector/depressor muscles of fish, which allowed the soft fins to be erected or folded within 0.3 s. We experimentally show that the biomimetic soft dorsal/anal fin can withstand external loading. We found that erecting the soft dorsal/anal fins significantly enhanced the linear acceleration rate, up to 32.5% over the folded fin state. Surprisingly, even though the projected area of the body (in the lateral plane) increased 16.9% when the median fins were erected, the magnitude of the side force oscillation decreased by 24.8%, which may have led to significantly less side-to-side sway in the robotic swimmer. Visualization of fluid flow in the wake of median fins reveals that during linear acceleration, the soft dorsal fin generates a wake flow opposite in direction to that of the caudal fin, which creates propulsive jets with time-variant circulations and jet angles. Erectable/foldable fins provide a new design space for bioinspired underwater robots with structures that morph to adapt to different locomotor behaviors. This biorobotic fish model is also a potentially promising system for studying the dynamics of complex multifin fish swimming behaviors, including linear acceleration, steady swimming, and burst and coast, which are difficult to analyze in freely swimming fishes.

Zoonotic parasites associated with felines from the Patagonian Holocene

Directory of Open Access Journals (Sweden)

Martín Horacio Fugassa

2009-12-01

Full Text Available Feline coprolites were examined for parasites with the aim of studying ancient infections that occurred in the Patagonian region during the Holocene period. Eggs compatible to Trichuris sp., Calodium sp., Eucoleus sp., Nematodirus sp., Oesophagostomum sp. (Nematoda, Monoecocestus sp. (Cestoda and Eimeria macusaniensis (Coccidia were recovered from faecal samples. The results obtained from the analysis provide evidence of consumption by felids of the viscera of both rodents and camelids. This knowledge allows for improved explanations as to the distribution of parasitism and its significance to the health of humans and animals inhabiting the area under study during the Middle Holocene.

Holocene lake-level fluctuations of Lake Aricota, Southern Peru

Science.gov (United States)

Placzek, C.; Quade, Jay; Betancourt, J.L.

2001-01-01

Lacustrine deposits exposed around Lake Aricota, Peru (17?? 22???S), a 7.5-km2 lake dammed by debris flows, provide a middle to late Holocene record of lake-level fluctuations. Chronological context for shoreline deposits was obtained from radiocarbon dating of vascular plant remains and other datable material with minimal 14C reservoir effects (Titicaca (16?? S), which is only 130 km to the northeast and shares a similar climatology. Comparisons with other marine and terrestrial records highlight emerging contradictions over the nature of mid-Holocene climate in the central Andes. ?? 2001 University of Washington.

Thermal-hydraulic performance of the finned surface of a compact heat exchanger

International Nuclear Information System (INIS)

Errasti Cabrera, Michel

2015-01-01

In this work the thermal-hydraulic behavior of the finned surface of a compact heat exchanger is obtained in tube-fin configuration corrugated (wavy). Through numerical simulation are determined average values ​​of intensification of heat transfer and pressure loss in the inter-channel finned. The objective is to characterize the surface to use as a reference, to make comparisons with other heat exchange surfaces enhanced using traditional techniques combined with more current, such as vortex generators. The study is conducted in laminar flow, with Reynolds numbers below 1000. In the working model compact exchanger tubes and corrugated fins (wavy) heat is described, and the results of the coefficient of overall heat transfer and the pressure drop are explained from the local characteristics of the velocity field and temperature inside the heat exchanger. (Full text)

Identification des matériaux et étude du bâti : l’exemple du Clos du Cotentin

Directory of Open Access Journals (Sweden)

Julien Deshayes

2012-04-01

Full Text Available Partant de l’architecture vernaculaire de la Presqu’île du Cotentin, cette étude s’attache à montrer comment l'identification des matériaux de construction, replacée dans une problématique historique, peut fournir un outil d'analyse privilégié du bâti, notamment en matière de chronologie. L'identification des principaux centres carriers et de leur aire d'exportation permet de mieux appréhender l'évolution des modénatures et de raisonner sur des typologies cohérentes. L'acquisition de tels critères d'analyse, peu généralisables hors de régions très délimitées, est nécessairement liée à une expérience prolongée du terrain. L’exemple du Clos du Cotentin offre, en matière d'identification des matériaux et d'étude du bâti, un manifeste en faveur d'une approche topographique approfondie, susceptible de replacer l'architecture rurale dans le cadre d'une évolution historique.Based on the vernacular architecture of the Cotentin peninsula, this article sets out to show how the identification of construction materials, placed in a historical context, can offer a particularly useful tool for analysing buildings, notably for their chronology. The identification of the principle stone quarries and their zones of commercial influence gives information on the evolution of architectural proportions and permits the development of coherent typologies. The acquisition of such analytical criteria is difficult to generalise beyond strictly limited regions and are necessarily linked with in-depth familiarity with the territory concerned. The example that the Clos du Cotentin offers for the identification of building materials and the study of buildings may be seen as a manifesto in favour of a detailed topographical approach, capable of placing rural architecture in the framework of its historical evolution.

An Assessment of Some Watch Schedule Variants Used in Cdn Patrol Frigates: OP Nanook 2011

Science.gov (United States)

2012-12-01

évalué les horaires de garde utilisés à bord du NCSM St John’s à la fin de l’opération Nanook 2011, pendant les huit jours de la traversée du St...soit réalisée. Nous avons évalué les horaires de garde utilisés à bord du NCSM St John’s à la fin de l’opération Nanook 2011, pendant les huit jours de...FASTTM model for Subject 4 ( Bridge , bosun) ............................................................ 12  B.3  FASTTM model for Subject 7 (Operations

Patagonian and southern South Atlantic view of Holocene climate

Science.gov (United States)

Kaplan, M. R.; Schaefer, J. M.; Strelin, J. A.; Denton, G. H.; Anderson, R. F.; Vandergoes, M. J.; Finkel, R. C.; Schwartz, R.; Travis, S. G.; Garcia, J. L.; Martini, M. A.; Nielsen, S. H. H.

2016-06-01

We present a comprehensive 10Be chronology for Holocene moraines in the Lago Argentino basin, on the east side of the South Patagonian Icefield. We focus on three different areas, where prior studies show ample glacier moraine records exist because they were formed by outlet glaciers sensitive to climate change. The 10Be dated records are from the Lago Pearson, Herminita Península-Brazo Upsala, and Lago Frías areas, which span a distance of almost 100 km adjacent to the modern Icefield. New 10Be ages show that expanded glaciers and moraine building events occurred at least at 6120 ± 390 (n = 13), 4450 ± 220 (n = 7), 1450 or 1410 ± 110 (n = 18), 360 ± 30 (n = 5), and 240 ± 20 (n = 8) years ago. Furthermore, other less well-dated glacier expansions of the Upsala Glacier occurred between 1400 and ∼1000 and ∼2300 and ∼2000 years ago. The most extensive glaciers occurred over the interval from ∼6100 to ∼4500 years ago, and their margins over the last ∼600 years were well within and lower than those in the middle Holocene. The 10Be ages agree with 14C-limiting data for the glacier histories in this area. We then link southern South American, adjacent South Atlantic, and other Southern Hemisphere records to elucidate broader regional patterns of climate and their possible causes. In the early Holocene, a far southward position of the westerly winds fostered warmth, small Patagonian glaciers, and reduced sea ice coverage over the South Atlantic. Although we infer a pronounced southward displacement of the westerlies during the early Holocene, these conditions did not occur throughout the southern mid-high latitudes, an important exception being over the southwest Pacific sector. Subsequently, a northward locus and/or expansion of the winds over the Patagonia-South Atlantic sector promoted the largest glaciers between ∼6100 and ∼4500 years ago and greatest sea ice coverage. Over the last few millennia, the South Patagonian Icefield has experienced

Environmental changes and human settlement in the central Marches (Italy during the early-middle Holocene

Directory of Open Access Journals (Sweden)

Gilberto Calderoni

2007-12-01

centrales (Fig. 1 enregistrèrent une rapide amélioration du climat, caractérisée par des conditions tempérées-humides. On assiste à un vaste développement de la végétation méditerranéenne thermophile avec des forêts à latifoliées et d’épais sols bruns-calciques. Dans la haute vallée du fleuve Chienti, sur la base d’analyses polliniques de sédiments tourbeux (A. PAGANELLI, 1959, datés successivement 8260 ± 100 C14 yr BP et 7740 ± 80 C14 yr BP (G. CALDERONI et al., 1996, on a déterminé une association forestière à quercus, accompagné de carpinus et tilia, typiques d’un climat tempéré-chaud.Cette nouvelle couverture végétale a réduit drastiquement l’érosion sur les versants et la sédimentation fluviale,et a favorisé l’incision des dépôts alluviaux précédents dans les secteurs moyen-hauts des fleuves (G. CILLA et F. DRAMIS, 2000. Cependant, dans les vallées de montagne, l’érosion linéaire a été localement ralentie par le développement de barrages de travertin qui ont créé des ruptures du profil longitudinal des cours d’eau et de chutes. En amont des barrages, des étangs et des petits bassins lacustres se sont formés. Là se sont déposés des couches de sables phytoclastiques avec des niveaux argileux et tourbeux (G. CILLA et al., 1994 ; G. CALDERONI et al., 1996. La sédimentation fluviatile a continué dans de la zone orientale (Photo 1 jusqu’à environ 3500 ans BP avec la mise en place de matériaux fins (G. CILLA et al., 1996. Entre 5000 et 3500 ans BP les processus de sédimentation ont touché les systèmes hydrographiques en entier. Ensuite et jusqu’à l’époque post-romaine, l’incision fluviale a dominé de partout dans les Marches centrales, avec le développement de chenaux sinueux ou à méandre qui se sont réalisés lentement (M. COLTORTI, 1991.Après 3500 ans BP la sédimentation du travertin a subi une réduction, ce qui a provoqué l’incision des barrages et la disparition des

Contrasting pollen histories of MIS 5e and the Holocene from Lake Titicaca (Bolivia/Peru)

Science.gov (United States)

Hanselman, Jennifer A.; Gosling, William D.; Paduano, Gina M.; Bush, Mark B.

2005-10-01

Two long sediment records (cores LTO1-2B and LT01-3B) from Lake Titicaca, Bolivia/Peru, are compared with a previously analysed Holocene record from this lake (core NE98-1PC). The Holocene records of LT01-2B and NE98-1PC are similar. There are striking differences, however, between the MIS 5e sections of the long cores and the Holocene records. In these records, temperature is probably the dominant parameter that determines the total fossil pollen concentration and is used to time the onset and termination of deglaciation. In contrast, the relative and absolute abundance of specific taxa (e.g. Polylepis/Acaena, Chenopodiaceae) are indicators of relative moisture availability. Although the Holocene contains a period of aridity between ca. 8000 cal. yr BP and 4300 cal. yr BP, it is a minor event compared with the more extreme aridity of MIS 5e. Core LT01-3B showed similar trends during MIS 5e when compared to LT01-2B, as did NE98-1PC when comparing Holocene records. MIS 5e and the Holocene are markedly different interglacials, depicted by shifts in pollen concentration and taxa representation over time.

Dynamique des populations du foreur des tiges du cacaoyer ...

African Journals Online (AJOL)

Objectif : Le foreur de tiges du cacaoyer, Eulophonotus myrmeleon Felder cause aujourd'hui d'énormes dégâts dans les cacaoyères ivoiriennes. La présente étude vise à déterminer les périodes de fortes attaques de ce déprédateur dans la région du Haut-Sassandra, la deuxième plus grande région de production de ...

Effect of morphological fin curl on the swimming performance and station-holding ability of juvenile shovelnose sturgeon

Science.gov (United States)

Deslauriers, David; Johnston, Ryan; Chipps, Steven R.

2016-01-01

We assessed the effect of fin-curl on the swimming and station-holding ability of juvenile shovelnose sturgeon Scaphirhynchus platorynchus (mean fork length = 17 cm; mean weight = 16 g; n = 21) using a critical swimming speed test performed in a small swim chamber (90 L) at 20°C. We quantified fin-curl severity using the pectoral fin index. Results showed a positive relationship between pectoral fin index and critical swimming speed indicative of reduced swimming performance displayed by fish afflicted with a pectoral fin index < 8%. Fin-curl severity, however, did not affect the station-holding ability of individual fish. Rather, fish affected with severe fin-curl were likely unable to use their pectoral fins to position their body adequately in the water column, which led to the early onset of fatigue. Results generated from this study should serve as an important consideration for future stocking practices.

The FinTech phenomenon: antecedents of financial innovation perceived by the popular press

OpenAIRE

Zavolokina, Liudmila; Dolata, Mateusz; Schwabe, Gerhard

2016-01-01

The financial industry has been strongly influenced by digitalization in the past few years reflected by the emergence of 'FinTech,' which represents the marriage of 'finance' and 'information technology.' FinTech provides opportunities for the creation of new services and business models and poses challenges to traditional financial service providers. Therefore, FinTech has become a subject of debate among practitioners, investors, and researchers and is highly visible in the popular media. ...

Holocene deposition and megathrust splay fault geometries within Prince William Sound, Alaska

Science.gov (United States)

Finn, S.; Liberty, L. M.; Haeussler, P. J.; Pratt, T. L.

2011-12-01

New high resolution sparker seismic reflection data, in conjunction with reprocessed legacy seismic data, provide the basis for a new fault, fold, and Holocene sediment thickness database for Prince William Sound, Alaska. Additionally, legacy airgun seismic data in Prince William Sound and the Gulf of Alaska tie features on these new sparker data to deeper portions of megathrust splay faults. We correlate regionally extensive bathymetric lineaments within Prince William Sound to megathrust splay faults, such as the ones that ruptured in the 1964 M9.2 earthquake. Lastly, we estimate Holocene sediment thickness within Prince William Sound to better constrain the Holocene fault history throughout the region. We identify three seismic facies related to Holocene, Quaternary, and Tertiary strata that are crosscut by numerous high angle normal faults in the hanging wall of the megathrust splay faults. The crustal-scale seismic reflection profiles show splay faults emerging from 20 km depth between the Yakutat block and North American crust and surfacing as the Hanning Bay and Patton Bay faults. A change in exhumation rates, slip rates, and fault orientation appears near Hinchinbrook that we attribute to differences in subducted slab geometry. Based on our slip rate analysis, we calculate average Holocene displacements of 20 m and 100 m in eastern and western Prince William Sound, respectively. Landward of two splay faults exposed on Montague Island, we observe subsidence, faulting, and landslides that record deformation associated with the 1964 and older megathrust earthquakes.

Subcooled boiling heat transfer on a finned surface

International Nuclear Information System (INIS)

Kowalski, J.E.; Tran, V.T.; Mills, P.J.

1992-01-01

Experimental and numerical studies have been performed to determine the heat transfer coefficients from a finned cylindrical surface to subcooled boiling water. The heat transfer rates were measured in an annular test section consisting of an electrically heated fuel element simulator (FES) with eight longitudinal, rectangular fins enclosed in a glass tube. A two-dimensional finite-element heat transfer model using the Galerkin method was employed to determine the heat transfer coefficients along the periphery of the FES surface. An empirical correlation was developed to predict the heat transfer coefficients during subcooled boiling. The correlation agrees well with the measured data. (6 figures) (Author)

Effects of fin pitch and array of the frost layer growth on extended surface of a heat exchanger

International Nuclear Information System (INIS)

Yang, Dong Keun; Lee, Kwan Soo

2003-01-01

This paper presents the effects of the fin array and pitch on the frost layer growth of a heat exchanger. The numerical results are compared with experimental data of a cold plate to validate the present model, and agree well with experimental data within a maximum error of 8%. The characteristics of the frost formation on staggered fin array are somewhat different from those of in-line array. For fin pitch below 10 mm, the frost layer growth of second fin in the staggered array is affected by that of first fin. The heat transfer of single fin deteriorate with decreasing fin pitch regardless of fin array, however, the thermal performance of a heat exchanger, considering increase of heat surface area, becomes better

Optimization methodology for large scale fin geometry on the steel containment of a Public Acceptable Simple SMR (PASS)

International Nuclear Information System (INIS)

Kim, Do Yun; NO, Hee Cheon; Kim, Ho Sik

2015-01-01

Highlights: • Optimization methodology for fin geometry on the steel containment is established. • Optimum spacing is 7 cm in PASS containment. • Optimum thickness is 0.9–1.8 cm when a fin height is 10–25 cm. • Optimal fin geometry is determined in given fin height by overall effectiveness correlation. • 13% of material volume and 43% of containment volume are reduced by using fins. - Abstracts: Heat removal capability through a steel containment is important in accident situations to preserve the integrity of a nuclear power plant which adopts a steel containment concept. A heat transfer rate will be enhanced by using fins on the external surface of the steel containment. The fins, however, cause to increase flow resistance and to deteriorate the heat transfer rate at the same time. Therefore, this study investigates an optimization methodology of large scale fin geometry for a vertical base where a natural convection flow regime is turbulent. Rectangular plate fins adopted in the steel containment of a Public Acceptable Simple SMR (PASS) is used as a reference. The heat transfer rate through the fins is obtained from CFD tools. In order to optimize fin geometry, an overall effectiveness concept is introduced as a fin performance parameter. The optimizing procedure is starting from finding optimum spacing. Then, optimum thickness is calculated and finally optimal fin geometry is suggested. Scale analysis is conducted to show the existence of an optimum spacing which turns out to be 7 cm in case of PASS. Optimum thickness is obtained by the overall effectiveness correlation, which is derived from a total heat transfer coefficient correlation. The total heat transfer coefficient correlation of a vertical fin array is suggested considering both of natural convection and radiation. However, the optimum thickness is changed as a fin height varies. Therefore, optimal fin geometry is obtained as a function of a fin height. With the assumption that the heat

Anatomy and muscle activity of the dorsal fins in bamboo sharks and spiny dogfish during turning maneuvers.

Science.gov (United States)

Maia, Anabela; Wilga, Cheryl D

2013-11-01

Stability and procured instability characterize two opposing types of swimming, steady and maneuvering, respectively. Fins can be used to manipulate flow to adjust stability during swimming maneuvers either actively using muscle control or passively by structural control. The function of the dorsal fins during turning maneuvering in two shark species with different swimming modes is investigated here using musculoskeletal anatomy and muscle function. White-spotted bamboo sharks are a benthic species that inhabits complex reef habitats and thus have high requirements for maneuverability. Spiny dogfish occupy a variety of coastal and continental shelf habitats and spend relatively more time cruising in open water. These species differ in dorsal fin morphology and fin position along the body. Bamboo sharks have a larger second dorsal fin area and proportionally more muscle insertion into both dorsal fins. The basal and radial pterygiophores are plate-like structures in spiny dogfish and are nearly indistinguishable from one another. In contrast, bamboo sharks lack basal pterygiophores, while the radial pterygiophores form two rows of elongated rectangular elements that articulate with one another. The dorsal fin muscles are composed of a large muscle mass that extends over the ceratotrichia overlying the radials in spiny dogfish. However, in bamboo sharks, the muscle mass is divided into multiple distinct muscles that insert onto the ceratotrichia. During turning maneuvers, the dorsal fin muscles are active in both species with no differences in onset between fin sides. Spiny dogfish have longer burst durations on the outer fin side, which is consistent with opposing resistance to the medium. In bamboo sharks, bilateral activation of the dorsal in muscles could also be stiffening the fin throughout the turn. Thus, dogfish sharks passively stiffen the dorsal fin structurally and functionally, while bamboo sharks have more flexible dorsal fins, which result from a

Cyanobacterial Neurotoxin β-N-Methylamino-L-alanine (BMAA in Shark Fins

Directory of Open Access Journals (Sweden)

John Pablo

2012-02-01

Full Text Available Sharks are among the most threatened groups of marine species. Populations are declining globally to support the growing demand for shark fin soup. Sharks are known to bioaccumulate toxins that may pose health risks to consumers of shark products. The feeding habits of sharks are varied, including fish, mammals, crustaceans and plankton. The cyanobacterial neurotoxin β-N-methylamino-L-alanine (BMAA has been detected in species of free-living marine cyanobacteria and may bioaccumulate in the marine food web. In this study, we sampled fin clips from seven different species of sharks in South Florida to survey the occurrence of BMAA using HPLC-FD and Triple Quadrupole LC/MS/MS methods. BMAA was detected in the fins of all species examined with concentrations ranging from 144 to 1836 ng/mg wet weight. Since BMAA has been linked to neurodegenerative diseases, these results may have important relevance to human health. We suggest that consumption of shark fins may increase the risk for human exposure to the cyanobacterial neurotoxin BMAA.

Addressing FinFET metrology challenges in 1X node using tilt-beam CD-SEM

Science.gov (United States)

Zhang, Xiaoxiao; Zhou, Hua; Ge, Zhenhua; Vaid, Alok; Konduparthi, Deepasree; Osorio, Carmen; Ventola, Stefano; Meir, Roi; Shoval, Ori; Kris, Roman; Adan, Ofer; Bar-Zvi, Maayan

2014-04-01

At 1X node, 3D FinFETS raise a number of new metrology challenges. Gate height and fin height are two of the most important parameters for process control. At present there is a metrology gap in inline in-die measurement of these parameters. In order to fill this metrology gap, in-column beam tilt has been developed and implemented on Applied Materials V4i+ top-down CD-SEM for height measurement. A low tilt (5°) beam and a high tilt (14°) beam have been calibrated to obtain two sets of images providing measurement of sidewall edge width to calculate height in the host. Evaluations are done with applications in both gate height and fin height. TEM correlation with R2 being 0.89 and precision of 0.81nm have been achieved on various in-die features in gate height application. Fin height measurement shows less accuracy (R2 being 0.77) and precision (1.49 nm) due to challenges brought by fin geometry, yet still promising as first attempt. Sensitivity to DOE offset, die-to-die and in-die variation is demonstrated in both gate height and fin height. Process defect is successfully captured from inline wafers with gate height measurement implemented in production. This is the first successful demonstration of inline in-die gate height measurement for 14nm FinFET process control.

Ceramic finned-plate recuperator for industrial applications

Energy Technology Data Exchange (ETDEWEB)

Coombs, M.; Strumpf, H.; Kotchick, D.

1985-01-01

High-level recuperation of high-temperature industrial furnaces offers an economically effective means for improving both process and fuel utilization. A ceramic recuperator capable of operating in fuel gas temperatures of up to 1350/sup 0/C and providing a combustion air preheat temperature of 1100/sup 0/C can provide in excess of 50 percent savings in fuel comsumption over an unrecuperated furnace. This recuperator consists of an array of cast ceramic finned plates. The fin geometries are such that when the plates are stacked together, they form the heat transfer flow passages for both the flue gas and combustion air streams. A reference design for industrial recuperator system was created. The current development efforts conducted on this recuperator concept, as well as plans for future activities, are described.

Le Developmental Entrepreneurship Program du Massachusetts ...

International Development Research Centre (IDRC) Digital Library (Canada)

Faire en sorte que les étudiants venant des pays en développement pour étudier au MIT retournent ensuite dans leurs pays respectifs afin d'y concrétiser leurs idées est un souci majeur du MIT, des bailleurs de fonds et du milieu du développement. Ce projet palliera à ce souci en soutenant la formation des fellows du ...

Long-term forest dynamics at Gribskov, eastern Denmark with early-Holocene evidence for thermophilous broadleaved tree species

DEFF Research Database (Denmark)

Overballe-Petersen, Mette V; Nielsen, Anne Birgitte; Hannon, Gina E.

2012-01-01

two periods of the early Holocene and from c. 3000 cal. BP to present. The early-Holocene part of the record indicates a highly disturbed forest ecosystem with frequent fires and abundant macrofossils of particularly Betula sp. and Populus sp. The sediment stratigraphy and age–depth relationships give......We report on a full-Holocene pollen, charcoal and macrofossil record from a small forest hollow in Gribskov, eastern Denmark. The Fagus sylvatica pollen record suggests the establishment of a small Fagus population at Gribskov in the early Holocene together with early establishment of other...

The FinTech phenomenon: antecedents of financial innovation perceived by the popular press

OpenAIRE

Zavolokina, Liudmila; Dolata, Mateusz; Schwabe, Gerhard

2016-01-01

The financial industry has been strongly influenced by digitalization in the past few years reflected by the emergence of “FinTech,” which represents the marriage of “finance” and “information technology.” FinTech provides opportunities for the creation of new services and business models and poses challenges to traditional financial service providers. Therefore, FinTech has become a subject of debate among practitioners, investors, and researchers and is highly visible in the popular media. ...

The use of pelvic fins for benthic locomotion during foraging behavior in Potamotrygon motoro (Chondrichthyes: Potamotrygonidae

Directory of Open Access Journals (Sweden)

Akemi Shibuya

2015-06-01

Full Text Available Synchronized bipedal movements of the pelvic fins provide propulsion (punting during displacement on the substrate in batoids with benthic locomotion. In skates (Rajidae this mechanism is mainly generated by the crural cartilages. Although lacking these anatomical structures, some stingray species show modifications of their pelvic fins to aid in benthic locomotion. This study describes the use of the pelvic fins for locomotory performance and body re-orientation in the freshwater stingray Potamotrygon motoro (Müller & Henle, 1841 during foraging. Pelvic fin movements of juvenile individuals of P. motoro were recorded in ventral view by a high-speed camera at 250-500 fields/s-1. Potamotrygon motoro presented synchronous, alternating and unilateral movements of the pelvic fins, similar to those reported in skates. Synchronous movements were employed during straightforward motion for pushing the body off the substrate as well as for strike feeding, whereas unilateral movements were used to maneuver the body to the right or left during both locomotion and prey capture. Alternating movements of the pelvic fins are similar to bipedal movements in terrestrial and semi-aquatic tetrapods. The pelvic fins showed coordinated movements during feeding even when stationary, indicating that they have an important function in maintaining body posture (station holding during prey capture and manipulation. The use of pelvic fins during prey stalking may be advantageous because it results in less substrate disturbance when compared to movements generated by pectoral fin undulation. The range of pelvic fin movements indicates more complex control and coordination of the pelvic radial muscles.

Charge based DC compact modeling of bulk FinFET transistor

Science.gov (United States)

Cerdeira, A.; Garduño, I.; Tinoco, J.; Ritzenthaler, R.; Franco, J.; Togo, M.; Chiarella, T.; Claeys, C.

2013-09-01

Multiple-gate MOSFETs became an industrial reality in the last years. Due to a pragmatic trade-off between CMOS process baselines compatibility, improved performance compared to planar bulk architecture, and cost, bulk FinFETs emerged as the technological solution to provide downscaling for the 14/22 nm technological nodes. In this work, a charge based DC compact model based on the SDDG Model is demonstrated for this new generation of FinFET transistors and describes continuously the transistor characteristics in all operating regions. Validating the model against two bulk FinFET baselines (NMOS, PMOS, various gate lengths and EOT), an excellent agreement is found for transfer and output characteristics (linear and saturation regimes), transconductance/output conductance, and gm/IDS characteristics. Temperature dependence is also taken into account and validated (T range from 25 °C up to 175 °C).

Analytical solution to convection-radiation of a continuously moving fin with temperature-dependent thermal conductivity

Directory of Open Access Journals (Sweden)

Moradi Amir

2013-01-01

Full Text Available In this article, the simultaneous convection-radiation heat transfer of a moving fin of variable thermal conductivity is studied. The differential transformation method (DTM is applied for an analytic solution for heat transfer in fin with two different profiles. Fin profiles are rectangular and exponential. The accuracy of analytic solution is validated by comparing it with the numerical solution that is obtained by fourth-order Runge-Kutta method. The analytical and numerical results are shown for different values of the embedding parameters. DTM results show that series converge rapidly with high accuracy. The results indicate that the fin tip temperature increases when ambient temperature increases. Conversely, the fin tip temperature decreases with an increase in the Peclet number, convection-conduction and radiation-conduction parameters. It is shown that the fin tip temperature of the exponential profile is higher than the rectangular one. The results indicate that the numerical data and analytical method are in a good agreement with each other.

Fluid dynamics of flapping aquatic flight in the bird wrasse: three-dimensional unsteady computations with fin deformation.

Science.gov (United States)

Ramamurti, Ravi; Sandberg, William C; Löhner, Rainald; Walker, Jeffrey A; Westneat, Mark W

2002-10-01

Many fishes that swim with the paired pectoral fins use fin-stroke parameters that produce thrust force from lift in a mechanism of underwater flight. These locomotor mechanisms are of interest to behavioral biologists, biomechanics researchers and engineers. In the present study, we performed the first three-dimensional unsteady computations of fish swimming with oscillating and deforming fins. The objective of these computations was to investigate the fluid dynamics of force production associated with the flapping aquatic flight of the bird wrasse Gomphosus varius. For this computational work, we used the geometry of the wrasse and its pectoral fin, and previously measured fin kinematics, as the starting points for computational investigation of three-dimensional (3-D) unsteady fluid dynamics. We performed a 3-D steady computation and a complete set of 3-D quasisteady computations for a range of pectoral fin positions and surface velocities. An unstructured, grid-based, unsteady Navier-Stokes solver with automatic adaptive remeshing was then used to compute the unsteady flow about the wrasse through several complete cycles of pectoral fin oscillation. The shape deformation of the pectoral fin throughout the oscillation was taken from the experimental kinematics. The pressure distribution on the body of the bird wrasse and its pectoral fins was computed and integrated to give body and fin forces which were decomposed into lift and thrust. The velocity field variation on the surface of the wrasse body, on the pectoral fins and in the near-wake was computed throughout the swimming cycle. We compared our computational results for the steady, quasi-steady and unsteady cases with the experimental data on axial and vertical acceleration obtained from the pectoral fin kinematics experiments. These comparisons show that steady state computations are incapable of describing the fluid dynamics of flapping fins. Quasi-steady state computations, with correct incorporation of

"Cirque du Freak."

Science.gov (United States)

Rivett, Miriam

2002-01-01

Considers the marketing strategies that underpin the success of the "Cirque du Freak" series. Describes how "Cirque du Freak" is an account of events in the life of schoolboy Darren Shan. Notes that it is another reworking of the vampire narrative, a sub-genre of horror writing that has proved highly popular with both adult and…

Holocene eolian activity in the Minot dune field, North Dakota

Science.gov (United States)

Muhs, D.R.; Stafford, Thomas W.; Been, J.; Mahan, S.A.; Burdett, J.; Skipp, G.; Rowland, Z.M.

1997-01-01

Stabilized eolian sand is common over much of the Great Plains region of the United States and Canada, including a subhumid area of ??? 1500 km2 near Minot, North Dakota. Eolian landforms consist of sand sheets and northwest-trending parabolic dunes. Dunes and sand sheets in the Minot field are presently stabilized by a cover of prairie grasses or oak woodland. Stratigraphic studies and accelerator mass spectrometry radiocarbon dating of paleosols indicate at least two periods of eolian sand movement in the late Holocene. Pedologic data suggest that all of the dune field has experienced late Holocene dune activity, though not all parts of the dune field may have been active simultaneously. Similar immobile element (Ti, Zr, La, Ce) concentrations support the interpretation that eolian sands are derived from local glaciofluvial and glaciolacustrine sediments. However, glaciolacustrine and glaciofluvial source sediments have high Ca concentrations from carbonate minerals, whereas dune sands are depleted in Ca. Because noneolian-derived soils in the area are calcareous, these data indicate that the Minot dune field may have had extended periods of activity in the Holocene, such that eolian abrasion removed soft carbonate minerals. The southwest-facing parts of some presently stabilized dunes were active during the 1930s drought, but were revegetated during the wetter years of the 1940s. These observations indicate that severe droughts accompanied by high temperatures are the most likely cause of Holocene eolian activity.

Aluminum-based one- and two-dimensional micro fin array structures: high-throughput fabrication and heat transfer testing

International Nuclear Information System (INIS)

Primeaux, Philip A; Zhang, Bin; Zhang, Xiaoman; Miller, Jacob; Meng, W J; KC, Pratik; Moore, Arden L

2017-01-01

Microscale fin array structures were replicated onto surfaces of aluminum 1100 and aluminum 6061 alloy (Al1100/Al6061) sheet metals through room-temperature instrumented roll molding. Aluminum-based micro fin arrays were replicated at room temperature, and the fabrication process is one with high throughput and low cost. One-dimensional (1D) micro fin arrays were made through one-pass rolling, while two-dimensional (2D) micro fin arrays were made by sequential 90° cross rolling with the same roller sleeve. For roll molding of 1D micro fins, fin heights greater than 600 µ m were achieved and were shown to be proportional to the normal load force per feature width. At a given normal load force, the fin height was further shown to scale inversely with the hardness of the sheet metal. For sequential 90° cross rolling, morphologies of roll molded 2D micro fin arrays were examined, which provided clues to understand how plastic deformation occurred under cross rolling conditions. A series of pool boiling experiments on low profile Al micro fin array structures were performed within Novec 7100, a widely used commercial dielectric coolant. Results for both horizontal and vertical surface orientations show that roll molded Al micro fin arrays can increase heat flux at fixed surface temperature as compared to un-patterned Al sheet. The present results further suggest that many factors beyond just increased surface area can influence heat transfer performance, including surface finish and the important multiphase transport mechanisms in and around the fin geometry. These factors must also be considered when designing and optimizing micro fin array structures for heat transfer applications. (paper)

Suivi après le traitement du cancer du sein

Science.gov (United States)

Sisler, Jeffrey; Chaput, Geneviève; Sussman, Jonathan; Ozokwelu, Emmanuel

2016-01-01

Résumé Objectif Offrir aux médecins de famille un résumé des recommandations fondées sur les données probantes pour guider les soins aux survivantes traitées pour le cancer du sein. Qualité des données Une recherche documentaire a été effectuée dans MEDLINE entre 2000 et 2016 à l’aide des mots-clés anglais suivants : breast cancer, survivorship, follow-up care, aftercare, guidelines et survivorship care plans, en se concentrant sur la revue des lignes directrices publiées récemment par les organismes nationaux de cancérologie. Les données étaient de niveaux I à III. Message principal Les soins aux survivantes comportent 4 facettes : surveillance et dépistage, prise en charge des effets à long terme, promotion de la santé et coordination des soins. La surveillance des récidives ne se traduit que par une mammographie annuelle, et le dépistage d’autres cancers doit suivre les lignes directrices basées sur la population. La prise en charge des effets à long terme du cancer et de son traitement aborde des problèmes courants tels la douleur, la fatigue, le lymphœdème, la détresse et les effets indésirables des médicaments, de même que les préoccupations à long terme comme la santé du cœur et des os. La promotion de la santé met en relief les bienfaits de l’activité chez les survivantes du cancer, avec l’accent mis sur l’activité physique. Les soins aux survivantes sont de meilleure qualité lorsque divers services et professionnels de la santé participent aux soins, et le médecin de famille joue un rôle important dans la coordination des soins. Conclusion Les médecins de famille sont de plus en plus souvent les principaux fournisseurs de soins de suivi après le traitement du cancer du sein. Le cancer du sein doit être considéré comme une affection médicale chronique, même chez les femmes en rémission, et les patientes profitent de la même approche que celle utilisée pour les autres affections chroniques en

Performance and cost benefits analysis of double-pass solar collector with and without fins

International Nuclear Information System (INIS)

Fudholi, Ahmad; Sopian, Kamaruzzaman; Ruslan, Mohd Hafidz; Othman, Mohd Yusof

2013-01-01

Highlights: • The thermal performances and cost analysis of the double-pass solar collector with and without fins absorber were discussed. • The theoretical and experimental study on the double-pass solar air collector with and without fins absorber was conducted. • The ratio of AC/AEG or the cost benefit ratio was presented. • The double-pass solar collector with fins absorber is more cost-effective compared to without fins absorber. - Abstract: The performance and cost benefit analysis of double-pass solar collector with and without fins have been conducted. The theoretical model using steady state analysis has been developed and compared with the experimental results. The performance curves of the double-pass solar collector with and without fins, which included the effects of mass flow rate and solar intensity on the thermal efficiency of the solar collector, were obtained. Results indicated that the thermal efficiency is proportional to the solar intensity at a specific mass flow rate. The thermal efficiency increased by 9% at a solar intensity of 425–790 W/m 2 and mass flow rate of 0.09 kg/s. The theoretical and experimental analysis showed a similar trend as well as close agreement. Moreover, a cost-effectiveness model has been developed examine the cost benefit ratio of double-pass solar collector with and without fins. Evaluation of the annual cost (AC) and the annual energy gain (AEG) of the collector were also performed. The results show that the double-pass solar collector with fins is more cost-effective compared to the double-pass solar collector without fins for mass flow rate of 0.01–0.07 kg/s. Also, simulations were obtained for the double-pass solar collector with fins at Nusselt number of 5.42–36.21. The energy efficiency of collector increases with the increase of Nusselt number. The results show that by increasing the Nusselt number simultaneously would drop the outlet temperature at any solar intensity. Increase in Nusselt number

Genomic Sequence of a Ranavirus Isolated from Short-Finned Eel (Anguilla australis)

DEFF Research Database (Denmark)

Subramaniam, Kuttichantran; Toffan, Anna; Cappellozza, Elisabetta

2016-01-01

The short-finned eel ranavirus (SERV) was isolated from short-finned eel imported to Italy from New Zealand. Phylogenomic analyses revealed that SERV is a unique member of the genus Ranavirus, family Iridoviridae, branching at the base of the tree near other fish ranaviruses....

Holocene climate changes in eastern Beringia (NW North America) – A systematic review of multi-proxy evidence

Science.gov (United States)

Kaufman, Darrell S.; Axford, Yarrow L.; Henderson, Andrew C.G.; McKay, Nicolas P.; Oswald, W. Wyatt; Saenger, Casey; Anderson, R. Scott; Bailey, Hannah L.; Clegg, Benjamin; Gajewski, Konrad; Hu, Feng Sheng; Jones, Miriam C.; Massa, Charly; Routson, Cody C.; Werner, Al; Wooller, Matthew J.; Yu, Zicheng

2016-01-01

Reconstructing climates of the past relies on a variety of evidence from a large number of sites to capture the varied features of climate and the spatial heterogeneity of climate change. This review summarizes available information from diverse Holocene paleoenvironmental records across eastern Beringia (Alaska, westernmost Canada and adjacent seas), and it quantifies the primary trends of temperature- and moisture-sensitive records based in part on midges, pollen, and biogeochemical indicators (compiled in the recently published Arctic Holocene database, and updated here to v2.1). The composite time series from these proxy records are compared with new summaries of mountain-glacier and lake-level fluctuations, terrestrial water-isotope records, sea-ice and sea-surface-temperature analyses, and peatland and thaw-lake initiation frequencies to clarify multi-centennial- to millennial-scale trends in Holocene climate change. To focus the synthesis, the paleo data are used to frame specific questions that can be addressed with simulations by Earth system models to investigate the causes and dynamics of past and future climate change. This systematic review shows that, during the early Holocene (11.7–8.2 ka; 1 ka = 1000 cal yr BP), rather than a prominent thermal maximum as suggested previously, temperatures were highly variable, at times both higher and lower than present (approximate mid-20th-century average), with no clear spatial pattern. Composited pollen, midge and other proxy records average out the variability and show the overall lowest summer and mean-annual temperatures across the study region during the earliest Holocene, followed by warming over the early Holocene. The sparse data available on early Holocene glaciation show that glaciers in southern Alaska were as extensive then as they were during the late Holocene. Early Holocene lake levels were low in interior Alaska, but moisture indicators show pronounced differences across the region. The highest

Ballistic electron transport calculation of strained germanium-tin fin field-effect transistors

International Nuclear Information System (INIS)

Lan, H.-S.; Liu, C. W.

2014-01-01

The dependence of ballistic electron current on Sn content, sidewall orientations, fin width, and uniaxial stress is theoretically studied for the GeSn fin field-effect transistors. Alloying Sn increases the direct Γ valley occupancy and enhances the injection velocity at virtual source node. (112 ¯ ) sidewall gives the highest current enhancement due to the rapidly increasing Γ valley occupancy. The non-parabolicity of the Γ valley affects the occupancy significantly. However, uniaxial tensile stress and the shrinkage of fin width reduce the Γ valley occupancy, and the currents are enhanced by increasing occupancy of specific indirect L valleys with high injection velocity

Investigation of defect-induced abnormal body current in fin field-effect-transistors

International Nuclear Information System (INIS)

Liu, Kuan-Ju; Tsai, Jyun-Yu; Lu, Ying-Hsin; Liu, Xi-Wen; Chang, Ting-Chang; Chen, Ching-En; Yang, Ren-Ya; Cheng, Osbert; Huang, Cheng-Tung

2015-01-01

This letter investigates the mechanism of abnormal body current at the linear region in n-channel high-k/metal gate stack fin field effect transistors. Unlike body current, which is generated by impact ionization at high drain voltages, abnormal body current was found to increase with decreasing drain voltages. Notably, the unusual body leakage only occurs in three-dimensional structure devices. Based on measurements under different operation conditions, the abnormal body current can be attributed to fin surface defect-induced leakage current, and the mechanism is electron tunneling to the fin via the defects, resulting in holes left at the body terminal

ETUDE DU COMPORTEMENT MECANIQUE DU BETON CELLULAIRE AUTOCLAVE PRODUIT EN ALGERIE

Directory of Open Access Journals (Sweden)

R BELOUETTAR

2002-12-01

Full Text Available Ce travail présente une étude expérimentale du comportement mécanique du béton cellulaire autoclavé. L’étude est portée essentiellement sur une série d’essais mécaniques en compression quasistatique à différentes vitesses de déformation variables entre 10-4 s-1 et 10 s-1 et à deux états différents (état sec et état saturé d’eau. En général, l’augmentation de la vitesse de déformation donne une augmentation de la contrainte critique du béton cellulaire autoclavé. Le béton cellulaire autoclavé présente une sensibilité à la vitesse de déformation positive. La valeur du module d’élasticité est proche de la valeur standard (1.5 GPa pour un béton cellulaire autoclavé de masse volumique égale à 500-550 kg/m3.

Experimental studies of Savonius wind turbines with variations sizes and fin numbers towards performance

Science.gov (United States)

Utomo, Ilham Satrio; Tjahjana, Dominicus Danardono Dwi Prija; Hadi, Syamsul

2018-02-01

The use of renewable energy in Indonesia is still low. Especially the use of wind energy. Wind turbine Savonius is one turbine that can work with low wind speed. However, Savonius wind turbines still have low efficiency. Therefore it is necessary to modify. Modifications by using the fin are expected to increase the positive drag force by creating a flow that can enter the overlap ratio of the gap. This research was conducted using experimental approach scheme. Parameters generated from the experiment include: power generator, power coefficient, torque coefficient. The experimental data will be collected by variation of fin area, horizontal finning, at wind speed 3 m/s - 4,85 m/s. Experimental results show that with the addition of fin can improve the performance of wind turbine Savonius 11%, and by using the diameter of 115 mm fin is able to provide maximum performance in wind turbine Savonius.

DETERMINATION OF TEMPERATURE DISTRIBUTION FOR ANNULAR FINS WITH TEMPERATURE DEPENDENT THERMAL CONDUCTIVITY BY HPM

Directory of Open Access Journals (Sweden)

Davood Domairry Ganji

2011-01-01

Full Text Available In this paper, homotopy perturbation method has been used to evaluate the temperature distribution of annular fin with temperature-dependent thermal conductivity and to determine the temperature distribution within the fin. This method is useful and practical for solving the nonlinear heat transfer equation, which is associated with variable thermal conductivity condition. The homotopy perturbation method provides an approximate analytical solution in the form of an infinite power series. The annular fin heat transfer rate with temperature-dependent thermal conductivity has been obtained as a function of thermo-geometric fin parameter and the thermal conductivity parameter describing the variation of the thermal conductivity.

Heat transfer, erosion and acid condensation characteristics for novel H-type finned oval tube

International Nuclear Information System (INIS)

Wang, Y; Zhao, X; Tang, G

2015-01-01

Low efficiency of heat transfer, acid corrosion and erosion of economizers affect the economy and security in coal-fired power plants significantly. The H-type finned oval tube is proposed to alleviate these problems. Based on the H-type finned oval tube, we investigated three novel types of fins, including bleeding dimples, longitudinal vortex generators (LVGs), and compound dimple-LVG. We considered the three aspects together, and obtained the heat transfer, acid condensation rate and erosion loss. The results show that the tube bank with the new structured fins can improve the performance on the three aspects, and the compound dimple-LVG performs the highest comprehensive effect. (paper)

Holocene vegetation, environment, and tephra recorded from Lake Pupuke, Auckland, New Zealand

International Nuclear Information System (INIS)

Horrocks, M.; Augustinus, P.; Deng, Y.; Shane, P.; Andersson, S.

2005-01-01

Lake Pupuke provides a near-complete, high-resolution environmental record of the Holocene from northern New Zealand. Tephra beds constrain the timing of a range of proxy indicators of environmental change, and demonstrate errors in a radiocarbon chronology. Agathis australis forest progressively increases from c. 7000 yr BP and, in conjunction with indicators of reduced biomass productivity, support a model of long-term climate change to drier conditions over the Holocene. However, except for Agathis, conifer-hardwood forest dominated mainly by Dacrydium cupressinum shows little change throughout the pre-human Holocene, suggesting environmental stability. Dramatic vegetation change occurred only within the last millennium as a result of large-scale Polynesian deforestation by fire. This happened a short time before the local eruption of c. 638 cal. yr BP Rangitoto Tephra. The identification of two eruptions of tephra from Rangitoto volcano has implications for future hazard planning in the Auckland region, because the volcanoes were previously considered single event centres. Changes in atmospheric circulation since the Late Glacial, possibly causing lower frequency of distal ashfall in Auckland during the Holocene, complicates the use of long-term records in hazard frequency assessment. (author). 39 refs., 7 figs., 2 tabs

High Arctic Holocene temperature record from the Agassiz ice cap and Greenland ice sheet evolution.

Science.gov (United States)

Lecavalier, Benoit S; Fisher, David A; Milne, Glenn A; Vinther, Bo M; Tarasov, Lev; Huybrechts, Philippe; Lacelle, Denis; Main, Brittany; Zheng, James; Bourgeois, Jocelyne; Dyke, Arthur S

2017-06-06

We present a revised and extended high Arctic air temperature reconstruction from a single proxy that spans the past ∼12,000 y (up to 2009 CE). Our reconstruction from the Agassiz ice cap (Ellesmere Island, Canada) indicates an earlier and warmer Holocene thermal maximum with early Holocene temperatures that are 4-5 °C warmer compared with a previous reconstruction, and regularly exceed contemporary values for a period of ∼3,000 y. Our results show that air temperatures in this region are now at their warmest in the past 6,800-7,800 y, and that the recent rate of temperature change is unprecedented over the entire Holocene. The warmer early Holocene inferred from the Agassiz ice core leads to an estimated ∼1 km of ice thinning in northwest Greenland during the early Holocene using the Camp Century ice core. Ice modeling results show that this large thinning is consistent with our air temperature reconstruction. The modeling results also demonstrate the broader significance of the enhanced warming, with a retreat of the northern ice margin behind its present position in the mid Holocene and a ∼25% increase in total Greenland ice sheet mass loss (∼1.4 m sea-level equivalent) during the last deglaciation, both of which have implications for interpreting geodetic measurements of land uplift and gravity changes in northern Greenland.

Thermal performance of a porus radial fin with natural convection and radiative heat losses

Directory of Open Access Journals (Sweden)

Darvishi M.T.

2015-01-01

Full Text Available An analytic (series solution is developed to describe the thermal performance of a porous radial fin with natural convection in the fluid saturating the fin and radiation heat loss from the top and bottom surfaces of the fin. The HAM results for the temperature distribution and base heat flux are compared with the direct numerical results and found to be very accurate.

Dynamique des populations du foreur des tiges du cacaoyer ...

African Journals Online (AJOL)

SARAH

30 nov. 2014 ... déprédateur dans la région du Haut-Sassandra, la deuxième plus grande région de production de cacao en. Côte d'ivoire. Méthodologie et résultats : L'étude a été réalisée de 2009 à 2013 dans les plantations villageoises de la région du Haut-Sassandra en Côte d'Ivoire. Les variations des taux d'attaques ...

Performance ‘S’ Type Savonius Wind Turbine with Variation of Fin Addition on Blade

Science.gov (United States)

Pamungkas, S. F.; Wijayanto, D. S.; Saputro, H.; Widiastuti, I.

2018-01-01

Wind power has been receiving attention as the new energy resource in addressing the ecological problems of burning fossil fuels. Savonius wind rotor is a vertical axis wind turbines (VAWT) which has relatively simple structure and low operating speed. These characteristics make it suitable for areas with low average wind speed as in Indonesia. To identify the performance of Savonius rotor in generating electrical energy, this research experimentally studied the effect of fin addition for the ‘S’ shape of Savonius VAWT. The fin is added to fill the space in the blade in directing the wind flow. This rotor has two turbine blades, a rotor diameter of 1.1 m and rotor height of 1.4 m, used pulley transmission system with 1:4.2 multiplication ratio, and used a generator type PMG 200 W. The research was conducted during dry season by measuring the wind speed in the afternoon. The average wind speed in the area is 2.3 m/s with the maximum of 4.5 m/s. It was found that additional fin significantly increase the ability of Savonius rotor VAWT to generate electrical energy shown by increasing of electrical power. The highest power generated is 13.40 Watt at a wind speed of 4.5 m/s by adding 1 (one) fin in the blade. It increased by 22.71% from the rotor blade with no additional fin. However, increasing number of fins in the blade was not linearly increase the electrical power generated. The wind rotor blade with 4 additional fins is indicated has the lowest performance, generating only 10.80 Watt electrical power, accounted lower than the one generated by no fin-rotor blade. By knowing the effect of the rotor shape, the rotor dimension, the addition of fin, transmission, and generator used, it is possible to determine alternative geometry design in increasing the electrical power generated by Savonius wind turbine.

La fin de l’American Dream

OpenAIRE

Christine Rifflart

2007-01-01

Le retournement qui s’est opéré sur le marché de l’immobilier aux États-Unis depuis le début de l’année 2006 intervient après une phase de croissance exceptionnelle qui rompt avec les tendances de long terme. Engagée en 1995 et peu affectée par la récession de 2001, la dynamique s’emballe à partir de 2003, conduisant à une surchauffe dans le secteur, qu’illustrent la flambée des prix et l’accélération du taux d’endettement des ménages (100 % du revenu des ménages en 2006). Simultanément, le m...

La longue marche du mouvement sportif camerounais : l'émergence du Comité Olympique Camerounais (1946–1964

Directory of Open Access Journals (Sweden)

Charitas Pascal

2016-01-01

Dans ces conditions et selon le statut particulier de ce territoire du « pré-carré » africain de la France, il s'agit de comprendre les étapes de l'institutionnalisation du sport camerounais au sein des atermoiements de la colonisation française puis les processus à l'œuvre dans l'émergence puis la création du Comité Olympique Camerounais (COC, symbole de l'émancipation du sport camerounais et marqueur de son intégration sur la scène sportive internationale, plus particulièrement olympique. Autrement dit, de 1946 et la mise sous tutelle par l'ONU du Cameroun français pour sa partie orientale à 1964 et la première participation du CNO du Cameroun aux Jeux olympiques de Tokyo, l'objectif est de saisir ici le passage d'un sport colonial à un sport postcolonial mettant en exergue le rôle de l'influence française et le rôle des cadres camerounais du secteur sportif.

Optimum design of vaporizer fin with liquefied natural gas by numerical analysis

International Nuclear Information System (INIS)

Jeong, Hyo Min; Chung, Han Shik; Lee, Sang Chul; Kong, Tae Woo; Yi, Chung Seub

2006-01-01

Generally, the temperature drop under 0 .deg. C on vaporizer surface creates frozen dews. This problem seems to increase as the time progress and humidity rises. In addition, the frozen dews create frost deposition. Consequently, heat transfer on vaporizer decreases because frost deposition causes adiabatic condition. Therefore, it is very important to solve this problem. This paper aims to study of the optimum design of used vaporizer at local LNG station. In this paper, experimental results were compared with numerical results. Geometries of numerical and experimental vaporizers were identical. Studied parameters of vaporizer are angle between two fins (Φ) and fin thickness (TH F ). Numerical analysis results were presented through the correlations between the ice layer thickness (TH ICE ) on the vaporizer surface to the temperature distribution of inside vaporizer (T IN ), fin thickness (TH F ), and angle between two fins (Φ). Numerical result shows good agreement with experimental outcome. Finally, the correlations for optimum design of vaporizer are proposed on this paper

Heat export from the tropics drives mid to late Holocene palaeoceanographic changes offshore southern Australia

Science.gov (United States)

Perner, Kerstin; Moros, Matthias; De Deckker, Patrick; Blanz, Thomas; Wacker, Lukas; Telford, Richard; Siegel, Herbert; Schneider, Ralph; Jansen, Eystein

2018-01-01

The Leeuwin Current (LC), an eastern boundary current, transports tropical waters from the Indo-Pacific Warm Pool (IPWP) towards southern latitudes and modulates oceanic conditions offshore southern Australia. New, high-resolution planktic foraminifer assemblage data and alkenone-derived sea surface temperatures (SST) provide an in-depth view on LC variability and mechanisms driving the current's properties during the mid to late Holocene (last c. 7.4 ka BP). Our marine reconstructions highlight a longer-term mid to late Holocene reduction of tropical heat export from the IPWP area into the LC. Mid Holocene (c. 7.4 to 3.5 ka BP) occurrence of high SSTs (>19.5 °C), tropical planktic foraminifera and a well-stratified water column document an enhanced heat export from the tropics. From c. 3.5 ka BP onwards, a weaker LC and a notably reduced tropical heat export cause oceanic cooling offshore southern Australia. The observed mid to late Holocene trends likely result from large-scale changes in the IPWP's heat storage linked to the El Niño-Southern Oscillation (ENSO) phenomenon. We propose that a strong and warm LC occurs in response to a La Niña-like state of ENSO during the mid Holocene. The late Holocene LC cooling, however, results from a shift towards an El Niño-like state and a more variable ENSO system that causes cooling of the IPWP. Superimposed on these longer-term trends we find evidence of distinct late Holocene millennial-scale phases of enhanced El Niño/La Niña development, which appear synchronous with northern hemispheric climatic variability. Phases of dominant El Niño-like states occur parallel to North Atlantic cold phases: the '2800 years BP cooling event', the 'Dark Ages' and the 'Little Ice Age', whereas the 'Roman Warm Period' and the 'Medieval Climate Anomaly' parallel periods of a predominant La Niña-like state. Our findings provide further evidence of coherent interhemispheric climatic and oceanic conditions during the mid to late

Phenotypic variation in dorsal fin morphology of coastal bottlenose dolphins (Tursiops truncatus off Mexico

Directory of Open Access Journals (Sweden)

Eduardo Morteo

2017-06-01

Full Text Available Geographic variation in external morphology is thought to reflect an interplay between genotype and the environment. Morphological variation has been well-described for a number of cetacean species, including the bottlenose dolphin (Tursiops truncatus. In this study we analyzed dorsal fin morphometric variation in coastal bottlenose dolphins to search for geographic patterns at different spatial scales. A total of 533 dorsal fin images from 19 available photo-identification catalogs across the three Mexican oceanic regions (Pacific Ocean n = 6, Gulf of California n = 6 and, Gulf of Mexico n = 7 were used in the analysis. Eleven fin shape measurements were analyzed to evaluate fin polymorphism through multivariate tests. Principal Component Analysis on log-transformed standardized ratios explained 94% of the variance. Canonical Discriminant Function Analysis on factor scores showed separation among most study areas (p < 0.05 with exception of the Gulf of Mexico where a strong morphometric cline was found. Possible explanations for the observed differences are related to environmental, biological and evolutionary processes. Shape distinction between dorsal fins from the Pacific and those from the Gulf of California were consistent with previously reported differences in skull morphometrics and genetics. Although the functional advantages of dorsal fin shape remains to be assessed, it is not unlikely that over a wide range of environments, fin shape may represent a trade-off among thermoregulatory capacity, hydrodynamic performance and the swimming/hunting behavior of the species.

Sådan kan du bruge optioner og futures

DEFF Research Database (Denmark)

Kohl, Niklas

2017-01-01

Masterclass. Har du brug for at forsikre værdierne i din portefølje i en periode, hvor du forventer stor uro på finansmarkederne, kan du gøre det med optioner eller futures. Her kan du læse om de forskellige typer – og om de muligheder de giver dig.......Masterclass. Har du brug for at forsikre værdierne i din portefølje i en periode, hvor du forventer stor uro på finansmarkederne, kan du gøre det med optioner eller futures. Her kan du læse om de forskellige typer – og om de muligheder de giver dig....

Differentiation of chondrocytes and scleroblasts during dorsal fin skeletogenesis in flounder larvae.

Science.gov (United States)

Suzuki, Tohru; Haga, Yutaka; Takeuchi, Toshio; Uji, Susumu; Hashimoto, Hisashi; Kurokawa, Tadahide

2003-01-01

In teleosts, the embryonic fin fold consists of a peridermis, an underlying epidermis and a small number of mesenchymal cells. Beginning from such a simple structure, the fin skeletons, including the proximal and distal radials and lepidotrichia (finrays), develop in the dorsal fin fold at the larval stage. Their process of skeletogenesis and embryonic origin are unclear. Using flounder larvae, we report the differentiation process for chondrocytes and scleroblasts prior to fin skeletogenesis and the effects of retinoic acid (RA) on it. In early larvae, the mesenchymal cells grow between the epidermis and spinal cord to form a line of periodical condensations, which are proximal radial primordia, to produce chondrocytes. The prescleroblasts, which ossify the proximal radial cartilages, differentiate in the mesenchymal cells remaining between the cartilages. Then, mesenchymal condensations occur between the distal ends of the proximal radials, forming distal radial primordia, to produce chondrocytes. Simultaneously, condensations occur between the distal radial primordia and peridermis, which are lepidotrichia primordia, to produce prescleroblasts. Exogenous RA specifically inhibits the mesenchymal condensation prior to the proximal radial formation together with the down-regulation of sonic hedgehog (shh) and patched (pta) expression, resulting in the loss of proximal radials. Thus, it was indicated that differentiation of the precursor cells of radials and lepidotrichia begins in the proximal part of the fin fold and that the initial mesenchymal condensation prior to the proximal radial formation is highly susceptible to the effects of RA. Lepidotrichia formation does not occur where proximal radials are absent, indicating that lepidotrichia differentiation requires interaction with the radial cartilages. To examine the suggestion that neural crest cells contribute to the medial fin skeletons, we localized the HNK-1 positive cells in flounder embryos and slug and

Aeolian processes during the Holocene in Gannan Region, Eastern Tibetan Plateau

Science.gov (United States)

Yang, S.; Cheng, T.; Li, S.; Liang, M.

2016-12-01

Aeolian desertification occurring in the Tibetan Plateau has received attention recently for it has become a severe environmental problem by accelerating the grassland degradation and eco-environment damage. The Gannan Region is located in the northeastern Tibetan Plateau with a mean altitude of 3500m. It is highly sensitive to global environmental change and human disturbance. Serious soil erosion and desertification and extensive land degradation have caused heavy eco-environmental impacts. To investigate the evolution of the desertification in Holocene in the Plateau is of great importance for understanding the desertification trend under the global changes in the Tibetan Plateau. Loess and aeolian sands is a key geological archive related to desertification processes and the past environment changes. In this study a typical 8.5m-thick loess-sands profile named MQQ, was selected at the Maqu city. It is situated on the first terrace (T1) of the Yellow River. Detailed accelerator mass spectrometry (AMS) 14C dating of bulk organic matter content has shown the Aeolian sediments of the MQQ section occurring since the early Holocene. the mass-specific frequency-dependent magnetic susceptibility (χfd) and grainsize records show a clear upward increase in the contents of superparamagnetic grains and fine fractions in grain size, which indicates a gradual wetting trend during the Holocene.The sediment rates change from very high in the early Holocene to low values after 8.2 ka. The wetting process can be divided into three steps: 10.0-8.2 ka, 8.2-3.0 ka and 3.0-present. It indicates that the climate in the eastern Tibetan Plateau was dry during the early Holocene. After that the climate was getting wet gradually. The variations of the westerlies and the Asian monsoon may cause the environmental change in this region.

Onset and Multiple Fluctuations of Holocene Glaciation in the Sierra Nevada, California

Science.gov (United States)

Bowerman, N. D.; Clark, D. H.

2004-12-01

Multiple sediment cores from two paternoster tarns (First and Second lakes) in North Fork Big Pine Creek, Sierra Nevada, preserve the most detailed and complete record of Holocene glaciation yet recovered in the range; they indicate that the glacier was absent during the early Holocene, reformed in the late Holocene, and experienced several expansions and contractions, culminating with the Matthes maximum during the last ˜200 years. The lakes are fed by outwash from the Palisade Glacier, the largest ( ˜1.3 km2) and presumably longest-lived glacier in the Sierra Nevada, and capture essentially all of the rock flour produced by the glacier. Distinct late-Holocene (Matthes) and late-Pleistocene (Recess Peak) moraines lie between the modern glacier and the lakes. Thus, the lakes have received continuous sedimentation since the retreat of the Tioga glacier ( ˜15,000 yr B.P.), and therefore capture rock flour related to all subsequent advances. First and Second lakes occupy relatively deep bedrock basins at 3036 m and 3066 m asl., respectively. Third Lake, a shallow (rock flour (outwash) from the upstream Palisade Glacier, most likely related to formation and expansions of the glacier in the late Holocene. The maximum peak at the top of the cores confirms the moraine record, which indicates that the maximum Holocene advance of Sierran glaciers occurred during the late Little Ice Age (last ˜200 yr) At least one tephra layer, possibly related to the Mono/Inyo dome complexes, occurs in the middle depths of the First Lake cores. Other narrow peaks in MS may also be associated with tephra deposits. Ongoing detailed analyses of the sediments, including AMS radiocarbon dating, visual and x-ray imaging, particle size analysis, organic content, tephrochronology, diatom assemblages, and palynology will constrain the timing and character of the environmental fluctuations related to the rock-flour flux. We will present results of these analyses at the meeting.

CFD analysis of fin tube heat exchanger with a pair of delta winglet vortex generators

International Nuclear Information System (INIS)

Hwang, Seong Won; Kim, Dong Hwan; Min, June Kee; Jeong, Ji Hwan

2012-01-01

Among tubular heat exchangers, fin tube types are the most widely used in refrigeration and air-conditioning equipment. Efforts to enhance the performance of these heat exchangers included variations in the fin shape from a plain fin to a slit and louver type. In the context of heat transfer augmentation, the performance of vortex generators has also been investigated. Delta winglet vortex generators have recently attracted research interest, partly due to experimental data showing that their addition to fin-tube heat exchangers considerably reduces pressure loss at heat transfer capacity of nearly the same level. The efficiency of the delta winglet vortex generators widely varies depending on their size and shape, as well as the locations where they are implemented. In this paper, the flow field around delta winglet vortex generators in a common flow up arrangement was analyzed in terms of flow characteristics and heat transfer using computational fluid dynamics methods. Flow mixing due to vortices and delayed separation due to acceleration influence the overall fin performance. The fin with delta winglet vortex generators exhibited a pressure loss lower than that of a plain fin, and the heat transfer performance was enhanced at high air velocity or Reynolds number

CFD analysis of fin tube heat exchanger with a pair of delta winglet vortex generators

Energy Technology Data Exchange (ETDEWEB)

Hwang, Seong Won; Kim, Dong Hwan; Min, June Kee; Jeong, Ji Hwan [Pusan National Univ., Busan (Korea, Republic of)

2012-09-15

Among tubular heat exchangers, fin tube types are the most widely used in refrigeration and air-conditioning equipment. Efforts to enhance the performance of these heat exchangers included variations in the fin shape from a plain fin to a slit and louver type. In the context of heat transfer augmentation, the performance of vortex generators has also been investigated. Delta winglet vortex generators have recently attracted research interest, partly due to experimental data showing that their addition to fin-tube heat exchangers considerably reduces pressure loss at heat transfer capacity of nearly the same level. The efficiency of the delta winglet vortex generators widely varies depending on their size and shape, as well as the locations where they are implemented. In this paper, the flow field around delta winglet vortex generators in a common flow up arrangement was analyzed in terms of flow characteristics and heat transfer using computational fluid dynamics methods. Flow mixing due to vortices and delayed separation due to acceleration influence the overall fin performance. The fin with delta winglet vortex generators exhibited a pressure loss lower than that of a plain fin, and the heat transfer performance was enhanced at high air velocity or Reynolds number.

La décadence à la fin du XIXe siècle espagnol: une esthétique de la provocation

Directory of Open Access Journals (Sweden)

Xavier Escudero

2012-03-01

In what way(s do these concepts both make use of and take part in an aesthetic of transgression, or a provocative pose? What does Spanish decadentism really mean, and what are its expressions? In order to answer these questions, we shall first look at the concept of decadentism as applied to the sociocultural phenomenon of Spanish literary bohemianism, which gathers writers and artists defined by constant failure, loose morals and the "cursed" poses they adopt. Then we shall highlight the literary expressions of decadence through the writings of Manuel Machado, Rubén Darío and Ramón María del Valle-Inclán, three prominent authors of the fin-de-siècle letters. Finally we shall take a closer look at the decadent motifs of marginality and lust in the little-known field of modernist bohemian poetry.

Paysans du Brésil

Directory of Open Access Journals (Sweden)

Dominique Temple

2007-01-01

Full Text Available Eric Sabourin, « Paysans du Brésil : Entre échange marchand et réciprocité » Paris, Editions Quae, 241p, 30 euros, (préface de Maxime Haubert, 2007Dans la présentation du livre, Maxime Haubert dit :«Cet ouvrage propose une analyse socio-anthropologique et agronomique des sociétés rurales et paysannes du Brésil et des transformations qu'elles ont connues ces dernières décennies, en particulier face aux interventions de l'Etat et à l'expansion du marché capitaliste (.... «Le livre pose d'abor...

Note: Dynamic analysis of a robotic fish motion with a caudal fin with vertical phase differences

Science.gov (United States)

Yun, Dongwon; Kim, Kyung-Soo; Kim, Soohyun; Kyung, Jinho; Lee, Sunghwi

2013-03-01

In this paper, a robotic fish with a caudal fin with vertical phase differences is studied, especially focusing on the energy consumption. Energies for thrusting a conventional robotic fish and one with caudal fin with vertical phase differences are obtained and compared each other. It is shown that a robotic fish with a caudal fin with vertical phase differences can save more energy, which implies the efficient thrusting via a vertically waving caudal fin.

Sedimentary alkenone distributions reflect salinity changes in the Baltic Sea over the Holocene

NARCIS (Netherlands)

Warden, L.A.; van der Meer, M.T.J.; Moros, Matthias; Sinninghe Damsté, J.S.

2016-01-01

The Baltic Sea has had a complex salinity history since the last deglaciation. Here we show how distributions of alkenones and their δD values varied with past fluctuations in salinity in the Baltic Sea over the Holocene by examining a Holocene record (11.2–0.1 cal kyr BP) from the Arkona Basin.

State of FinTech in Europe: Mutation perspectives of the banking sector

OpenAIRE

Marasco, Marco

2017-01-01

This paper studies the relationship between FinTech start-ups and the banking sector. The aim is to assess the impact that the FinTech sector might have on the business model and profitability of banks. Master [120] en sciences de gestion (Mons), Université catholique de Louvain, 2017

Del fin de la guerra fria al comienzo de la guerra sin fin

OpenAIRE

Ferrier, Jean Pierre

2006-01-01

El Profesor Ferrier nos describe los acontecimientos de la sociedad internacional en los ultimos 15 años y señala la profunda diferencia entre "la estabilidad" durante la guerra fría y la "revolucion" que se ha producido en el escenario internacional a partir de la caida del muro de Berlin. Hace especial referencia al comportamiento de la superpotencia (Estados Unidos) y su guerra sin fin contra los "nuevos enemigos" en los diferentes teatros internacionales en su lucha por imponer el "Bien" ...

Numerical analysis on interactions between fluid flow and structure deformation in plate-fin heat exchanger by Galerkin method

Science.gov (United States)

Liu, Jing-cheng; Wei, Xiu-ting; Zhou, Zhi-yong; Wei, Zhen-wen

2018-03-01

The fluid-structure interaction performance of plate-fin heat exchanger (PFHE) with serrated fins in large scale air-separation equipment was investigated in this paper. The stress and deformation of fins were analyzed, besides, the interaction equations were deduced by Galerkin method. The governing equations of fluid flow and heat transfer in PFHE were deduced by finite volume method (FVM). The distribution of strain and stress were calculated in large scale air separation equipment and the coupling situation of serrated fins under laminar situation was analyzed. The results indicated that the interactions between fins and fluid flow in the exchanger have significant impacts on heat transfer enhancement, meanwhile, the strain and stress of fins includes dynamic pressure of the sealing head and flow impact with the increase of flow velocity. The impacts are especially significant at the conjunction of two fins because of the non-alignment fins. It can be concluded that the soldering process and channel width led to structure deformation of fins in the exchanger, and degraded heat transfer efficiency.