WorldWideScience

Sample records for field measurement technique

  1. Full-field wafer warpage measurement technique

    Science.gov (United States)

    Hsieh, H. L.; Lee, J. Y.; Huang, Y. G.; Liang, A. J.; Sun, B. Y.

    2017-06-01

    An innovative moiré technique for full-field wafer warpage measurement is proposed in this study. The wafer warpage measurement technique is developed based on moiré method, Talbot effect, scanning profiling method, stroboscopic, instantaneous phase-shift method, as well as four-step phase shift method, high resolution, high stability and full-field measurement capabilities can be easily achieved. According to the proposed full-field optical configuration, a laser beam is expanded into a collimated beam with a 2-inch diameter and projected onto the wafer surface. The beam is reflected by the wafer surface and forms a moiré fringe image after passing two circular gratings, which is then focused and captured on a CCD camera for computation. The corresponding moiré fringes reflected from the wafer surface are obtained by overlapping the images of the measuring grating and the reference grating. The moiré fringes will shift when wafer warpage occurs. The phase of the moiré fringes will change proportionally to the degree of warpage in the wafer, which can be measured by detecting variations in the phase shift of the moiré fringes in each detection points on the surface of the entire wafer. The phase shift variations of each detection points can be calculated via the instantaneous phase-shift method and the four-step phase-shift method. By adding up the phase shift variations of each detection points along the radii of the circular gratings, the warpage value and surface topography of the wafer can be obtained. Experiments show that the proposed method is capable of obtaining test results similar to that of a commercial sensor, as well as performing accurate measurements under high speed rotation of 1500rpm. As compared to current warpage measurement methods such as the beam optical method, confocal microscopy, laser interferometry, shadow moiré method, and structured light method, this proposed technique has the advantage of full-field measurement, high

  2. Techniques to measure complex-plane fields

    CSIR Research Space (South Africa)

    Dudley, Angela L

    2014-09-25

    Full Text Available In this work we construct coherent superpositions of Gaussian and vortex modes which can be described to occupy the complex-plane. We demonstrate how these fields can be experimentally constructed in a digital, controllable manner with a spatial...

  3. Spherical near-field antenna measurements — The most accurate antenna measurement technique

    DEFF Research Database (Denmark)

    Breinbjerg, Olav

    2016-01-01

    The spherical near-field antenna measurement technique combines several advantages and generally constitutes the most accurate technique for experimental characterization of radiation from antennas. This paper/presentation discusses these advantages, briefly reviews the early history and present...... status, and addresses future challenges for spherical near-field antenna measurements; in particular, from the viewpoint of the DTU-ESA Spherical Near-Field Antenna Test Facility....

  4. The Evolving Field of Wound Measurement Techniques: A Literature Review.

    Science.gov (United States)

    Khoo, Rachel; Jansen, Shirley

    2016-06-01

    Wound healing is a complex and multifactorial process that requires the involvement of a multidisciplinary approach. Methods of wound measurement have been developed and continually refined with the purpose of ensuring precision in wound measurement and documentation as the primary indicator of healing. This review aims to ascertain the efficacies of current wound area measurement techniques, and to highlight any perceived gaps in the literature so as to develop suggestions for future studies and practice. Med- line, PubMed, CliniKey, and CINAHL were searched using the terms "wound/ulcer measurement techniques," "wound assessment," "digi- tal planimetry," and "structured light." Articles between 2000 and 2014 were selected, and secondary searches were carried out by exam- ining the references of relevant articles. Only papers written in English were included. A universal, standardized method of wound as- sessment has not been established or proposed. At present, techniques range from the simple to the more complex - most of which have char- acteristics that allow for applicability in both rural and urban settings. Techniques covered are: ruler measurements, acetate tracings/contact planimetry, digital planimetry, and structured light devices. Conclu- sion. In reviewing the literature, the precision and reliability of digital planimetry over the more conventional methods of ruler measurements and acetate tracings are consistently demonstrated. The advent and utility of the laser or structured light approach, however, is promising, has only been analyzed by a few, and opens up the scope for further evaluation of this technique.

  5. Measurement of field-free molecular alignment by balanced weak field polarization technique

    Directory of Open Access Journals (Sweden)

    Peng Peng

    2015-12-01

    Full Text Available We demonstrate the measurement of field-free molecular alignment of air can be realized by combining the weak field polarization technique (WFPT with a balanced detection system. The measured signal is proportional to the alignment parameter. Periodic revival structures of the transient alignment and permanent alignment between revivals can be detected clearly by a single measurement with high sensitivity. Fourier transform spectrum of the measured signal agrees well with the calculation result and provides information of the populations of different J states in the rotational wave packet.

  6. Advanced spherical near-field antenna measurement techniques

    DEFF Research Database (Denmark)

    Nielsen, Jeppe Majlund; Pivnenko, Sergey; Breinbjerg, Olav

    2011-01-01

    The DTU-ESA facility has since the 1980es provided highly accurate antenna radiation pattern measurements and gain calibration by use of the probe corrected spherical nearfield technique, both for ESA (the European Space Agency) and other customers and continues to do so. Recent years activities ...

  7. Full-field laser vibration measurement in NDT techniques

    Science.gov (United States)

    Yue, Kaiduan; Li, Zhongke; Yi, Yaxing; Zhang, Fei

    2008-12-01

    Research of Non Destructive Testing (NDT) methodology has developed rapidly in recent years[1][2]. But it is rarely used for small objects such as Micro-electronic Mechanics System. Due to the small size of the MEMS, the traditional method of contact measurement seriously affects the parameter of the object measured. So a high accuracy non-contact measurement is required for optimization of MEMS designs and improvement of its reliability[3][4]. With recent advances in photonics, electronics, and computer technology, a Non Destructive Testing (NDT) laser time average interferometry is proposed in the paper. Laser interferometry has the advantages of non-contact, high accuracy, full-field and fast speed, so it can be used to detect cracks in MEMS. A time average measurement method of digital speckle pattern interferometry is proposed to measure the vibration mode of the MEMS in the paper. According to the sudden change of amplitude of vibration mode, a crack can be measured. With the speckle average technology, high accuracy phase-shift, continuous phase scanning technology, combined with optical amplification technology, the resolution of the amplitude reaches 1nm, and the resolution of the crack reaches 5μm. The measurement system being full-field, the measuring speed of the measurement system can reach 512*512 points per one minute.

  8. Advanced spherical near-field antenna measurement techniques

    DEFF Research Database (Denmark)

    Nielsen, Jeppe Majlund; Pivnenko, Sergey; Breinbjerg, Olav

    2011-01-01

    The DTU-ESA facility has since the 1980es provided highly accurate antenna radiation pattern measurements and gain calibration by use of the probe corrected spherical nearfield technique, both for ESA (the European Space Agency) and other customers and continues to do so. Recent years activities...... and showing the capabilities of each participating facility. A special campaign was carried out with the aim of establishing a reference radiation pattern for the DTU-ESA VAST-12 antenna. The on-ground calibration of the MIRAS space radiometer for ESA's SMOS mission was carried out at the DTU-ESA facility...

  9. A High-Resolution Antenna Diagnostics Technique for Spherical Nesr-Field Measurements

    DEFF Research Database (Denmark)

    Cappellin, Cecilia; Breinbjerg, Olav; Frandsen, Aksel

    2005-01-01

    A new diagnostics technique for spherical near-field antenna measurements, that can provide a high spatial resolution of the reconstructed aperture field, is presented. This technique is realized by transforming the spherical wave expansion (SWE) of the radiated field into the corresponding plane...

  10. Field Measurements

    CERN Document Server

    Bottura, L

    2004-01-01

    The measurement of the magnetic field is often the final verification of the complex design and fabrication process of a magnetic system. In several cases, when seeking high accuracy, the measurement technique and its realization can result in a considerable effort. This note describes most used measurement techniques, such as nuclear magnetic resonance, fluxmeters and Hall generators, and their typical range of application. In addition some of less commonly used techniques, such as magneto-optical, SQUIDs, or particle beams methods, are listed.

  11. Double phi-Step theta-Scanning Technique for Spherical Near-Field Antenna Measurements

    DEFF Research Database (Denmark)

    Laitinen, Tommi

    2008-01-01

    Probe-corrected spherical near-field antenna measurements with an arbitrary probe set certain requirements on an applicable scanning technique. The computational complexity of the general high-order probe correction technique for an arbitrary probe, that is based on the Phi scanning, is O(N4), wh...

  12. Study of density field measurement based on NPLS technique in supersonic flow

    Institute of Scientific and Technical Information of China (English)

    2009-01-01

    Due to the influence of shock wave and turbulence, supersonic density field exhibits strongly inhomogeneous and unsteady characteristics. Applying traditional density field measurement techniques to supersonic flows yields three problems: low spatiotemporal resolution, limitation of measuring 3D density field, and low signal to noise ratio (SNR). A new method based on Nano-based Planar Laser Scattering (NPLS) technique is proposed in this paper to measure supersonic density field. This method measures planar transient density field in 3D supersonic flow by calibrating the relationship between density and concentration of tracer particles, which would display the density fluctuation due to the influence of shock waves and vortexes. The application of this new method to density field measurement of supersonic optical bow cap is introduced in this paper, and the results reveal shock wave, turbulent boundary layer in the flow with the spatial resolution of 93.2 μm/pixel. By analyzing the results at interval of 5 μs, temporal evolution of density field can be observed.

  13. Study of density field measurement based on NPLS technique in supersonic flow

    Institute of Scientific and Technical Information of China (English)

    TIAN LiFeng; YI ShiHe; ZHAO YuXin; HE Lin; CHENG ZhongYu

    2009-01-01

    Due to the influence of shock wave and turbulence,supersonic density field exhibits strongly inho-mogeneous and unsteady characteristics.Applying traditional density field measurement techniques to supersonic flows yields three problems: low spatiotemporal resolution,limitation of measuring 3D density field,and low signal to noise ratio (SNR).A new method based on Nano-based Planar Laser Scattering (NPLS) technique is proposed in this paper to measure supersonic density field.This method measures planar transient density field in 3D supersonic flow by calibrating the relationship between density and concentration of tracer particles,which would display the density fluctuation due to the influence of shock waves and vortexes.The application of this new method to density field measurement of supersonic optical bow cap is introduced in this paper,and the results reveal shock wave,turbulent boundary layer in the flow with the spatial resolution of 93.2 pm/pixel.By analyzing the results at interval of 5 μs,temporal evolution of density field can be observed.

  14. Velocity field measurements in an evaporating sessile droplet by means of micro-PIV technique

    Directory of Open Access Journals (Sweden)

    Yagodnitsyna Anna

    2016-01-01

    Full Text Available Velocity fields are measured in evaporating sessile droplets on two substrates with different contact angles and contact angle hysteresis using micro resolution particle image velocimetry technique. Different flow patterns are observed in different stages of droplet evaporation: a flow with vortices and a radial flow. Flow structure is found to be similar for droplets on different substrates.

  15. Investigations of some rock stress measuring techniques and the stress field in Norway

    Energy Technology Data Exchange (ETDEWEB)

    Hanssen, Tor Harald

    1997-12-31

    Rock stresses are important to the safe construction and operation of all man-made structures in rock, whether In mining, civil or petroleum engineering. The crucial issue is their relative magnitude and orientation. This thesis develops equipment and methods for further rock stress assessment and reevaluates existing overcoring rock stress measurements, and relates this information to the present geological setting. Both laboratory work and field work are involved. In the field, rock stresses are measured by the overcoring and the hydraulic fracturing technique. An observation technique for assessing likely high stresses is developed. The field data refer to several hydropower projects and to some offshore hydrocarbon fields. The principal sections are: (1) Tectonic setting in the western Fennoscandia, (2) Triaxial rock stress measurements by overcoring using the NTH cell (a strain gauge cell developed at the Norwegian technical university in Trondheim and based on the CSIR cell of the South African Council for Scientific and Industrial Research), (3) Laboratory testing of the NTH cell, (4) Quality ranking of stresses measured by the NTH cell, (4) Recalculated rock stresses and implications to the regional stress field, (5) Hydraulic fracturing stress measurements. 113 refs., 98 figs., 62 tabs.

  16. About the parametrizations utilized to perform magnetic moments measurements using the transient field technique

    Science.gov (United States)

    Gómez, A. M.; Torres, D. A.

    2016-07-01

    The experimental study of nuclear magnetic moments, using the Transient Field technique, makes use of spin-orbit hyperfine interactions to generate strong magnetic fields, above the kilo-Tesla regime, capable to create a precession of the nuclear spin. A theoretical description of such magnetic fields is still under theoretical research, and the use of parametrizations is still a common way to address the lack of theoretical information. In this contribution, a review of the main parametrizations utilized in the measurements of Nuclear Magnetic Moments will be presented, the challenges to create a theoretical description from first principles will be discussed.

  17. A First/Third-Order Probe Correction Technique for Spherical Near-Field Antenna Measurements Using Three Probe Orientations

    DEFF Research Database (Denmark)

    Laitinen, Tommi; Breinbjerg, Olav

    2008-01-01

    A probe correction technique is described for spherical near-field antenna measurements based on sampling the near field for three probe orientations in each measurement direction. The technique applies to odd-order probes whose radiated field contains (significant) power only in the first (µ=±1)...

  18. Electric field measurements on Cluster: comparing the double-probe and electron drift techniques

    Directory of Open Access Journals (Sweden)

    A. I. Eriksson

    2006-03-01

    Full Text Available The four Cluster satellites each carry two instruments designed for measuring the electric field: a double-probe instrument (EFW and an electron drift instrument (EDI. We compare data from the two instruments in a representative sample of plasma regions. The complementary merits and weaknesses of the two techniques are illustrated. EDI operations are confined to regions of magnetic fields above 30 nT and where wave activity and keV electron fluxes are not too high, while EFW can provide data everywhere, and can go far higher in sampling frequency than EDI. On the other hand, the EDI technique is immune to variations in the low energy plasma, while EFW sometimes detects significant nongeophysical electric fields, particularly in regions with drifting plasma, with ion energy (in eV below the spacecraft potential (in volts. We show that the polar cap is a particularly intricate region for the double-probe technique, where large nongeophysical fields regularly contaminate EFW measurments of the DC electric field. We present a model explaining this in terms of enhanced cold plasma wake effects appearing when the ion flow energy is higher than the thermal energy but below the spacecraft potential multiplied by the ion charge. We suggest that these conditions, which are typical of the polar wind and occur sporadically in other regions containing a significant low energy ion population, cause a large cold plasma wake behind the spacecraft, resulting in spurious electric fields in EFW data. This interpretation is supported by an analysis of the direction of the spurious electric field, and by showing that use of active potential control alleviates the situation.

  19. Advancement of an Infra-Red Technique for Whole-Field Concentration Measurements in Fluidized Beds

    Science.gov (United States)

    Medrano, Jose A.; de Nooijer, Niek C. A.; Gallucci, Fausto; van Sint Annaland, Martin

    2016-01-01

    For a better understanding and description of the mass transport phenomena in dense multiphase gas-solids systems such as fluidized bed reactors, detailed and quantitative experimental data on the concentration profiles is required, which demands advanced non-invasive concentration monitoring techniques with a high spatial and temporal resolution. A novel technique based on the selective detection of a gas component in a gas mixture using infra-red properties has been further developed. The first stage development was carried out using a very small sapphire reactor and CO2 as tracer gas. Although the measuring principle was demonstrated, the real application was hindered by the small reactor dimensions related to the high costs and difficult handling of large sapphire plates. In this study, a new system has been developed, that allows working at much larger scales and yet with higher resolution. In the new system, propane is used as tracer gas and quartz as reactor material. In this study, a thorough optimization and calibration of the technique is presented which is subsequently applied for whole-field measurements with high temporal resolution. The developed technique allows the use of a relatively inexpensive configuration for the measurement of detailed concentration fields and can be applied to a large variety of important chemical engineering topics. PMID:26927127

  20. Advancement of an Infra-Red Technique for Whole-Field Concentration Measurements in Fluidized Beds

    Directory of Open Access Journals (Sweden)

    Jose A. Medrano

    2016-02-01

    Full Text Available For a better understanding and description of the mass transport phenomena in dense multiphase gas-solids systems such as fluidized bed reactors, detailed and quantitative experimental data on the concentration profiles is required, which demands advanced non-invasive concentration monitoring techniques with a high spatial and temporal resolution. A novel technique based on the selective detection of a gas component in a gas mixture using infra-red properties has been further developed. The first stage development was carried out using a very small sapphire reactor and CO2 as tracer gas. Although the measuring principle was demonstrated, the real application was hindered by the small reactor dimensions related to the high costs and difficult handling of large sapphire plates. In this study, a new system has been developed, that allows working at much larger scales and yet with higher resolution. In the new system, propane is used as tracer gas and quartz as reactor material. In this study, a thorough optimization and calibration of the technique is presented which is subsequently applied for whole-field measurements with high temporal resolution. The developed technique allows the use of a relatively inexpensive configuration for the measurement of detailed concentration fields and can be applied to a large variety of important chemical engineering topics.

  1. A gated four probe technique for field effect measurements on disordered organic semiconductors

    Energy Technology Data Exchange (ETDEWEB)

    Hauff, E. von; Spethmann, N.; Parisi, J. [Carl von Ossietzky Univ. of Oldenburg (Germany). Dept. for Energy and Semiconductor Research

    2008-09-15

    A gated four probe measurement technique to isolate contact resistances in field effect measurements on disordered organic semiconductors was investigated. Organic field effect transistors (OFETs) were prepared with two additional electrodes in the contact geometry protruding into the source-drain channel to monitor the variation in potential across the channel. Two high impedance electrometers were used to determine the potential at the contacts. This technique allows to directly determine the magnitude of the parasitic contact resistances between metal contact and organic semiconductor from the drop in potential at the contact regions. The effects of contact resistances, which can falsify measurements on bulk transport parameters such as the field effect mobility, can be then eliminated during material characterization. Additionally, the temperature and electric field dependence of the contact resistances offers valuable information about the charge injection and extraction processes between metal and organic semiconductor. The effects of the four probe geometry, specifically the effect of the channel electrodes on the current-voltage characteristics, of hole transport in a polythiophene (P3HT) OFET with Au contacts were investigated and found not to influence device performance, except at currents <<1 nA. The IV characteristics were shown to follow the expected FET behaviour. From the variation in potential along the channel it was found that contact resistances at the source contact (charge injecting contact) are minimal while contact resistances at the drain contact (charge extracting contact) are significant, resulting in a much lower effective source-drain voltage than that applied to the device. (orig.)

  2. Protein Structure: Alignment using Mean Field Techniques and Measurement of Isolated Individual Molecules

    Energy Technology Data Exchange (ETDEWEB)

    Blankenbecler, Richard

    2003-03-13

    Techniques originally developed in High Energy Physics have been applied to selected problems in genetics with promising results. First, this talk will briefly review the importance of protein structure from a physics point of view. Then Mean Field Techniques used in detector track fitting algorithms will be applied to the comparison of protein structures. The practical importance of such comparisons will be discussed. Second, the possibility of measuring the charge structure of ''single'' isolated molecules using the proposed SLAC Free Electron Laser will be outlined. This involves the development of an algorithm that determines the orientation of each of the many targeted identical molecules, constructs the 3-D transform from the many 2-D patterns, and finally performs an inverse fourier transform when only the magnitude of the transform is known, since the phase is not measurable.

  3. New experimental technique for the measurement of the velocity field in thin films falling over obstacles

    Science.gov (United States)

    Landel, Julien R.; Daglis, Ana; McEvoy, Harry; Dalziel, Stuart B.

    2014-11-01

    We present a new experimental technique to measure the surface velocity of a thin falling film. Thin falling films are important in various processes such as cooling in heat exchangers or cleaning processes. For instance, in a household dishwasher cleaning depends on the ability of a thin draining film to remove material from a substrate. We are interested in the impact of obstacles attached to a substrate on the velocity field of a thin film flowing over them. Measuring the velocity field of thin falling films is a challenging experimental problem due to the small depth of the flow and the large velocity gradient across its depth. We propose a new technique based on PIV to measure the plane components of the velocity at the surface of the film over an arbitrarily large area and an arbitrarily large resolution, depending mostly on the image acquisition technique. We perform experiments with thin films of water flowing on a flat inclined surface, made of glass or stainless steel. The typical Reynolds number of the film is of the order of 100 to 1000, computed using the surface velocity, the film thickness and the kinematic viscosity of the film. We measure the modification to the flow field, from a viscous-gravity regime, caused by small solid obstacles, such as three-dimensional hemispherical obstacles and two-dimensional steps. We compare our results with past theoretical and numerical studies. This material is based upon work supported by the Defense Threat Reduction Agency under Contract No. HDTRA1-12-D-0003-0001.

  4. A sound field separation technique based on measurements with pressure-velocity probes

    DEFF Research Database (Denmark)

    Zhang, Yong-Bin; Chen, Xin-Zhao; Jacobsen, Finn

    2009-01-01

    It has recently been shown that statistically optimized near field acoustic holography based on measurement with an array of pressure-velocity transducers makes it possible to distinguish between sources on the two sides of the array and thus suppress the influence of a disturbing source [F....... Jacobsen and V. Jaud, J. Acoust. Soc. Am. 121, 1550-1558 (2007)]. However, the suggested technique uses a transfer matrix optimized for the source under test and may be expected to perform less well when the disturbing source is not placed symmetrically on the other side of the array, and this will usually...

  5. Simultaneous measurement of droplet size and velocity field by an interferometric imaging technique in spray combustion

    Energy Technology Data Exchange (ETDEWEB)

    Fujisawa, N.; Hosokawa, A.; Tomimatsu, S. [Niigata Univ. (Japan). Dept. of Mechanical and Production Engineering

    2003-08-01

    The present paper describes an experimental technique of droplet sizing and velocity measurement for application to a luminous flame in spray combustion. The size measurement of unburnt fuel droplets in combustion is carried out by using an interferometric imaging method, while the corresponding velocity field is measured by particle tracking velocimetry (PTV) in combination with the rotary shutter to avoid the high intensity noise of the luminous flame in spray combustion. The measurements are successfully applied to the spray flow from a gun-type burner with and without combustion. The experimental results in spray combustion indicate that the smaller size of fuel droplets are almost burnt in the centre of the flame and the unburnt droplets of larger size remain in the outer region of the burner flow. It was found that the mean droplet velocity measured by the present PTV technique in combustion is almost independent of the droplet size and agrees closely with the gas velocity. However, the velocity magnitude with combustion is increased in comparison with the case without combustion, which suggests the influence of gas expansion at high temperatures. (author)

  6. Mapping Tamarix: New techniques for field measurements, spatial modeling and remote sensing

    Science.gov (United States)

    Evangelista, Paul H.

    Native riparian ecosystems throughout the southwestern United States are being altered by the rapid invasion of Tamarix species, commonly known as tamarisk. The effects that tamarisk has on ecosystem processes have been poorly quantified largely due to inadequate survey methods. I tested new approaches for field measurements, spatial models and remote sensing to improve our ability measure and to map tamarisk occurrence, and provide new methods that will assist in management and control efforts. Examining allometric relationships between basal cover and height measurements collected in the field, I was able to produce several models to accurately estimate aboveground biomass. The best two models were explained 97% of the variance (R 2 = 0.97). Next, I tested five commonly used predictive spatial models to identify which methods performed best for tamarisk using different types of data collected in the field. Most spatial models performed well for tamarisk, with logistic regression performing best with an Area Under the receiver-operating characteristic Curve (AUC) of 0.89 and overall accuracy of 85%. The results of this study also suggested that models may not perform equally with different invasive species, and that results may be influenced by species traits and their interaction with environmental factors. Lastly, I tested several approaches to improve the ability to remotely sense tamarisk occurrence. Using Landsat7 ETM+ satellite scenes and derived vegetation indices for six different months of the growing season, I examined their ability to detect tamarisk individually (single-scene analyses) and collectively (time-series). My results showed that time-series analyses were best suited to distinguish tamarisk from other vegetation and landscape features (AUC = 0.96, overall accuracy = 90%). June, August and September were the best months to detect unique phenological attributes that are likely related to the species' extended growing season and green-up during

  7. Precise Measurement of a Magnetic Field Generated by the Electromagnetic Flux Compression Technique

    CERN Document Server

    Nakamura, D; Matsuda, Y H; Takeyama, S

    2013-01-01

    The precision of the values of a magnetic field generated by electromagnetic flux compression was investigated in ultra-high magnetic fields of up to 700 T. In an attempt to calibrate the magnetic field measured by pickup coils, precise Faraday rotation (FR) measurements were conducted on optical (quartz and crown) glasses. A discernible "turn-around" phenomenon was observed in the FR signal as well as the pickup coils before the end of a liner implosion. We found that the magnetic field measured by pickup coils should be corrected by taking into account the high-frequency response of the signal transmission line. Near the peak magnetic field, however, the pickup coils failed to provide reliable values, leaving the FR measurement as the only method to precisely measure an extremely high magnetic fields.

  8. Precise measurement of a magnetic field generated by the electromagnetic flux compression technique.

    Science.gov (United States)

    Nakamura, D; Sawabe, H; Matsuda, Y H; Takeyama, S

    2013-04-01

    The precision of the values of a magnetic field generated by electromagnetic flux compression was investigated in ultra-high magnetic fields of up to 700 T. In an attempt to calibrate the magnetic field measured by pickup coils, precise Faraday rotation (FR) measurements were conducted on optical (quartz and crown) glasses. A discernible "turn-around" phenomenon was observed in the FR signal as well as the pickup coils before the end of a liner implosion. We found that the magnetic field measured by pickup coils should be corrected by taking into account the high-frequency response of the signal transmission line. Near the peak magnetic field, however, the pickup coils failed to provide reliable values, leaving the FR measurement as the only method to precisely measure extremely high magnetic fields.

  9. Measuring aortic pulse wave velocity using high-field cardiovascular magnetic resonance: comparison of techniques

    Directory of Open Access Journals (Sweden)

    Shaffer Jean M

    2010-05-01

    Full Text Available Abstract Background The assessment of arterial stiffness is increasingly used for evaluating patients with different cardiovascular diseases as the mechanical properties of major arteries are often altered. Aortic stiffness can be noninvasively estimated by measuring pulse wave velocity (PWV. Several methods have been proposed for measuring PWV using velocity-encoded cardiovascular magnetic resonance (CMR, including transit-time (TT, flow-area (QA, and cross-correlation (XC methods. However, assessment and comparison of these techniques at high field strength has not yet been performed. In this work, the TT, QA, and XC techniques were clinically tested at 3 Tesla and compared to each other. Methods Fifty cardiovascular patients and six volunteers were scanned to acquire the necessary images. The six volunteer scans were performed twice to test inter-scan reproducibility. Patient images were analyzed using the TT, XC, and QA methods to determine PWV. Two observers analyzed the images to determine inter-observer and intra-observer variabilities. The PWV measurements by the three methods were compared to each other to test inter-method variability. To illustrate the importance of PWV using CMR, the degree of aortic stiffness was assessed using PWV and related to LV dysfunction in five patients with diastolic heart failure patients and five matched volunteers. Results The inter-observer and intra-observer variability results showed no bias between the different techniques. The TT and XC results were more reproducible than the QA; the mean (SD inter-observer/intra-observer PWV differences were -0.12(1.3/-0.04(0.4 for TT, 0.2(1.3/0.09(0.9 for XC, and 0.6(1.6/0.2(1.4 m/s for QA methods, respectively. The correlation coefficients (r for the inter-observer/intra-observer comparisons were 0.94/0.99, 0.88/0.94, and 0.83/0.92 for the TT, XC, and QA methods, respectively. The inter-scan reproducibility results showed low variability between the repeated

  10. A technique of reconstructing field for measuring sound reflection coefficients at arbitrary angles of incidence

    Institute of Scientific and Technical Information of China (English)

    HE Yuanan; LI Rui; HE Zuoyong

    2001-01-01

    An improved reconstructing field method for measuring sound reflection coefficient of a large impedance surface at arbitrary incident angles is proposed in this paper. In order to get the reflection coefficient by the Spatial Transformation of Sound Fields (STSF), the complex pressure on two parallel plashes near by the material surface or the reflection surface must be measured. By the acoustic intensity measurement, the phases of complex pressure on two parallel planes are given. The results of the numerical simulations are shown that the error due to the finite size of the measurement area, and it may be reduced by using a dipole sound source.

  11. A mountain watershed hydrology field course: Experiential learning in hydrologic concepts and measurement techniques

    Science.gov (United States)

    Hogue, T. S.; Kinoshita, A. M.; Randell, J.

    2013-12-01

    A field mountainshed hydrology course was offered annually since April 2006 to investigate and quantify hydrologic processes in the Sagehen experimental watershed in the Sierra Nevada, California. This advanced field-based course was offered through the University of California, Los Angeles (UCLA) Civil and Environmental Engineering (CEE) and was primarily for upper division undergraduate students in the hydrology emphasis track. This unique ten-week course focused on the study of catchment processes in snow-dominated and mountainous regions. The course offered a range of activities, including quantifying distributed watershed fluxes, investigating geochemical properties of surface and groundwater systems, measuring channel dynamics and stream morphology, and analysis of snowpack properties. A major component of the course included an extended field trip to Sagehen where students undertook a range of observations and field experiments. Pre-field trip coursework required an in-depth analysis of historical streamflow, precipitation, snow and other regional hydroclimatological data. At Sagehen, students worked together in teams while gaining a range of field experiences. Post-field trip labs included analysis of their collected field data and comparison to previous years' data, culminating in a comprehensive final report and shared with the Sagehen Creek Field Station as part of a cooperative effort. This presentation will highlight course, laboratory and field design, a compilation of observational results, and insight on lessons learned through the course history.

  12. A comparison of TPS and different measurement techniques in small-field electron beams

    Energy Technology Data Exchange (ETDEWEB)

    Donmez Kesen, Nazmiye, E-mail: nazo94@gmail.com; Cakir, Aydin; Okutan, Murat; Bilge, Hatice

    2015-04-01

    In recent years, small-field electron beams have been used for the treatment of superficial lesions, which requires small circular fields. However, when using very small electron fields, some significant dosimetric problems may occur. In this study, dose distributions and outputs of circular fields with dimensions of 5 cm and smaller, for nominal energies of 6, 9, and 15 MeV from the Siemens ONCOR Linac, were measured and compared with data from a treatment planning system using the pencil-beam algorithm in electron beam calculations. All dose distribution measurements were performed using the Gafchromic EBT film; these measurements were compared with data that were obtained from the Computerized Medical Systems (CMS) XiO treatment planning system (TPS), using the gamma-index method in the PTW VeriSoft software program. Output measurements were performed using the Gafchromic EBT film, an Advanced Markus ion chamber, and thermoluminescent dosimetry (TLD). Although the pencil-beam algorithm is used to model electron beams in many clinics, there is no substantial amount of detailed information in the literature about its use. As the field size decreased, the point of maximum dose moved closer to the surface. Output factors were consistent; differences from the values obtained from the TPS were, at maximum, 42% for 6 and 15 MeV and 32% for 9 MeV. When the dose distributions from the TPS were compared with the measurements from the Gafchromic EBT films, it was observed that the results were consistent for 2-cm diameter and larger fields, but the outputs for fields of 1-cm diameter and smaller were not consistent. In CMS XiO TPS, calculated using the pencil-beam algorithm, the dose distributions of electron treatment fields that were created with circular cutout of a 1-cm diameter were not appropriate for patient treatment and the pencil-beam algorithm is not convenient for monitor unit (MU) calculations in electron dosimetry.

  13. Diagnostic techniques for measurement of aerodynamic noise in free field and reverberant environment of wind tunnels

    Science.gov (United States)

    El-Sum, H. M. A.; Mawardi, O. K.

    1973-01-01

    Techniques for studying aerodynamic noise generating mechanisms without disturbing the flow in a free field, and in the reverberation environment of the ARC wind tunnel were investigated along with the design and testing of an acoustic antenna with an electronic steering control. The acoustic characteristics of turbojet as a noise source, detection of direct sound from a source in a reverberant background, optical diagnostic methods, and the design characteristics of a high directivity acoustic antenna. Recommendations for further studies are included.

  14. A goal-oriented field measurement filtering technique for the identification of material model parameters

    KAUST Repository

    Lubineau, Gilles

    2009-05-16

    The post-processing of experiments with nonuniform fields is still a challenge: the information is often much richer, but its interpretation for identification purposes is not straightforward. However, this is a very promising field of development because it would pave the way for the robust identification of multiple material parameters using only a small number of experiments. This paper presents a goal-oriented filtering technique in which data are combined into new output fields which are strongly correlated with specific quantities of interest (the material parameters to be identified). Thus, this combination, which is nonuniform in space, constitutes a filter of the experimental outputs, whose relevance is quantified by a quality function based on global variance analysis. Then, this filter is optimized using genetic algorithms. © 2009 Springer-Verlag.

  15. A Magnetic Resonance Measurement Technique for Rapidly Switched Gradient Magnetic Fields in a Magnetic Resonance Tomograph

    Directory of Open Access Journals (Sweden)

    K. Bartušek

    2003-01-01

    Full Text Available This paper describes a method for measuring of the gradient magnetic field in Nuclear Magnetic Resonance (NMR tomography, which is one of the modern medical diagnostic methods. A very important prerequisite for high quality imaging is a gradient magnetic field in the instrument with exactly defined properties. Nuclear magnetic resonance enables us to measure the pulse gradient magnetic field characteristics with high accuracy. These interesting precise methods were designed, realised, and tested at the Institute of Scientific Instruments (ISI of the Academy of Sciences of the Czech Republic. The first of them was the Instantaneous Frequency (IF method, which was developed into the Instantaneous Frequency of Spin Echo (IFSE and the Instantaneous Frequency of Spin Echo Series (IFSES methods. The above named methods are described in this paper and their a comparison is also presented.

  16. Sensitivities of various probe correction techniques to noise and inaccurate channel balance in spherical near-field antenna measurements

    DEFF Research Database (Denmark)

    Laitinen, Tommi; Pivnenko, Sergey; Breinbjerg, Olav

    2005-01-01

    Sensitivities of various probe correction techniques to noise and inaccurate channel balance in the spherical near-field antenna measurements are investigated. The simulation results show the level of uncertainty in the determination of the directivity of an antenna in the presence of -60 dB noise......, and as a function of the level of error in the channel balance for the different probe correction techniques....

  17. New measurements techniques

    DEFF Research Database (Denmark)

    Torras Rosell, Antoni

    of the pressure encountered by the ‘sensing’ light when traveling through the acoustic field. Far from being a limitation, this integral principle is exploited for sound field visualization using tomography. The most innovative contribution of this PhD project is the applicability of the acousto-optic measuring......Acoustic measurements are traditionally based on transducers, and in particular, the most advanced measurement techniques are nowadays based on transducer arrays. This poses a fundamental problem, namely the influence of the transducer itself on the actual properties of sound when the transducer...... is immersed into the sound field. Typically, this influence is assumed to be negligible when the size of the transducer is small compared to the wavelength of the sound wave, or is rendered negligible by using a transducerbased correction that depends on the frequency. Either solution introduces additional...

  18. Accessing interior magnetic field vector components in neutron electric dipole moment experiments via exterior measurements, I. Boundary-value techniques

    CERN Document Server

    Plaster, B

    2013-01-01

    We propose a new concept for determining the interior magnetic field vector components in neutron electric dipole moment experiments. If a closed three-dimensional boundary surface surrounding the fiducial volume of an experiment can be defined such that its interior encloses no currents or sources of magnetization, each of the interior vector field components and the magnetic scalar potential will satisfy a Laplace equation. Therefore, if either the vector field components or the normal derivative of the scalar potential can be measured on the surface of this boundary, thus defining a Dirichlet or Neumann boundary-value problem, respectively, the interior vector field components or the scalar potential (and, thus, the field components via the gradient of the potential) can be uniquely determined via solution of the Laplace equation. We discuss the applicability of this technique to the determination of the interior magnetic field components during the operating phase of neutron electric dipole moment experim...

  19. Radar Cross-Section Measurement Using the Near-Field Single-Frequency Angular-Diversity Technique

    Institute of Scientific and Technical Information of China (English)

    2000-01-01

    Radar cross-section(RCS)measurement with the near-field electromagnetic wave illu mination of a target has been proved to be practical.The existing methods employ the multiplefrequency angular-diversity(MFAD)technique,whereas this paper considers the single-frequency angular-diversity(SFAD)technique.The paper takes into account the scattering center modeling and the limitation of higher sidelobes in reconstructing images in the SFAD technique compared to the MFAD technique.A method of combining the SFAD technique with the RELAX approach is presented for the high-resolutionextraction of scattering centers on a target.The proposed method offers an excellent RCS recovery,which is validated by numerical results.

  20. Progress Toward a Technique for Measuring Electric Field Fluctuations in Tokamak Core Plasmas

    Science.gov (United States)

    Thompson, D. S.; Bakken, M. R.; Burke, M. G.; Couto, H. P.; Fonck, R. J.; Lewicki, B. T.; Winz, G. R.

    2014-10-01

    Measurements of electric field fluctuations in magnetic confinement experiments are desired for validating turbulence and transport models. A new diagnostic to measure Ez (r , t) fluctuations is in development on the Pegasus Toroidal Experiment. The approach is based on neutral beam emission spectroscopy using a high-throughput, high-resolution spectrometer to resolve fluctuations in wavelength separation between components of the motional Stark effect spectrum. Fluctuations at mid-minor-radius, normalized to an estimated MSE field, are estimated to be δE /EMSE ~ 10-3. In order to resolve fluctuations at turbulent time scales (fNy ~ 500 kHz), beam and spectrometer designs minimize broadening and maximize signal-to-noise ratio. The diagnostic employs a Fabry-Pérot spectrometer with étendue-matched collection optics and low noise detectors. The interferometer spacing is varied across the face of the etalon to mitigate geometric Doppler broadening. An 80 keV H0 beam from PBX-M with a divergence Ω deployment on larger fusion facilities. Work supported by US DOE Grant DE-FG02-89ER53296.

  1. Velocity field measurement in gas-liquid metal two-phase flow with use of PIV and neutron radiography techniques

    Energy Technology Data Exchange (ETDEWEB)

    Saito, Y.; Mishima, K. [Kyoto Univ. Kumatori, Research Reactor Institute, Osaka (Japan); Tobita, Y.; Suzuki, T. [O-arai Engineering Center, Power Reactor and Nuclear Fuel Development Corporation (Japan); Matsubayashi, M. [Japan Atomic Energy Institute, Tokai Research Establishment (Japan)

    2001-07-01

    Neutron radiography and PIV (Particle Image Velocimetry) techniques were applied to measurements of velocity field in gas-liquid metal two-phase flow. Visualization and measurements of two-phase flow were conducted using molten lead bismuth and nitrogen gas as working fluids and particles made of gold-cadmium (AuCd{sub 3}) inter-metallic alloy were employed as the tracer. Discrimination method between bubble and tracer images in two-phase flow was developed based on the {sigma}-scaling method. Time-averaged liquid velocity fields, gas velocity fields and void profile were calculated from discriminated images, respectively. From these measurements, the basic characteristics of gas-liquid metal two-phase mixture were clarified. (author)

  2. Evaluation of single and multiple Doppler lidar techniques to measure complex flow during the XPIA field campaign

    Energy Technology Data Exchange (ETDEWEB)

    Choukulkar, Aditya; Brewer, W. Alan; Sandberg, Scott P.; Weickmann, Ann; Bonin, Timothy A.; Hardesty, R. Michael; Lundquist, Julie K.; Delgado, Ruben; Iungo, G. Valerio; Ashton, Ryan; Debnath, Mithu; Bianco, Laura; Wilczak, James M.; Oncley, Steven; Wolfe, Daniel

    2017-01-01

    Accurate three-dimensional information of wind flow fields can be an important tool in not only visualizing complex flow but also understanding the underlying physical processes and improving flow modeling. However, a thorough analysis of the measurement uncertainties is required to properly interpret results. The XPIA (eXperimental Planetary boundary layer Instrumentation Assessment) field campaign conducted at the Boulder Atmospheric Observatory (BAO) in Erie, CO, from 2 March to 31 May 2015 brought together a large suite of in situ and remote sensing measurement platforms to evaluate complex flow measurement strategies.

    In this paper, measurement uncertainties for different single and multi-Doppler strategies using simple scan geometries (conical, vertical plane and staring) are investigated. The tradeoffs (such as time–space resolution vs. spatial coverage) among the different measurement techniques are evaluated using co-located measurements made near the BAO tower. Sensitivity of the single-/multi-Doppler measurement uncertainties to averaging period are investigated using the sonic anemometers installed on the BAO tower as the standard reference. Finally, the radiometer measurements are used to partition the measurement periods as a function of atmospheric stability to determine their effect on measurement uncertainty.

    It was found that with an increase in spatial coverage and measurement complexity, the uncertainty in the wind measurement also increased. For multi-Doppler techniques, the increase in uncertainty for temporally uncoordinated measurements is possibly due to requiring additional assumptions of stationarity along with horizontal homogeneity and less representative line-of-sight velocity statistics. It was also found that wind speed measurement uncertainty was lower during stable conditions compared to unstable conditions.

  3. Evaluation of single and multiple Doppler lidar techniques to measure complex flow during the XPIA field campaign

    Science.gov (United States)

    Choukulkar, Aditya; Brewer, W. Alan; Sandberg, Scott P.; Weickmann, Ann; Bonin, Timothy A.; Hardesty, R. Michael; Lundquist, Julie K.; Delgado, Ruben; Valerio Iungo, G.; Ashton, Ryan; Debnath, Mithu; Bianco, Laura; Wilczak, James M.; Oncley, Steven; Wolfe, Daniel

    2017-01-01

    Accurate three-dimensional information of wind flow fields can be an important tool in not only visualizing complex flow but also understanding the underlying physical processes and improving flow modeling. However, a thorough analysis of the measurement uncertainties is required to properly interpret results. The XPIA (eXperimental Planetary boundary layer Instrumentation Assessment) field campaign conducted at the Boulder Atmospheric Observatory (BAO) in Erie, CO, from 2 March to 31 May 2015 brought together a large suite of in situ and remote sensing measurement platforms to evaluate complex flow measurement strategies. In this paper, measurement uncertainties for different single and multi-Doppler strategies using simple scan geometries (conical, vertical plane and staring) are investigated. The tradeoffs (such as time-space resolution vs. spatial coverage) among the different measurement techniques are evaluated using co-located measurements made near the BAO tower. Sensitivity of the single-/multi-Doppler measurement uncertainties to averaging period are investigated using the sonic anemometers installed on the BAO tower as the standard reference. Finally, the radiometer measurements are used to partition the measurement periods as a function of atmospheric stability to determine their effect on measurement uncertainty. It was found that with an increase in spatial coverage and measurement complexity, the uncertainty in the wind measurement also increased. For multi-Doppler techniques, the increase in uncertainty for temporally uncoordinated measurements is possibly due to requiring additional assumptions of stationarity along with horizontal homogeneity and less representative line-of-sight velocity statistics. It was also found that wind speed measurement uncertainty was lower during stable conditions compared to unstable conditions.

  4. SEM technique for imaging and measuring electronic transport in nanocomposites based on electric field induced contrast

    Science.gov (United States)

    Jesse, Stephen [Knoxville, TN; Geohegan, David B [Knoxville, TN; Guillorn, Michael [Brooktondale, NY

    2009-02-17

    Methods and apparatus are described for SEM imaging and measuring electronic transport in nanocomposites based on electric field induced contrast. A method includes mounting a sample onto a sample holder, the sample including a sample material; wire bonding leads from the sample holder onto the sample; placing the sample holder in a vacuum chamber of a scanning electron microscope; connecting leads from the sample holder to a power source located outside the vacuum chamber; controlling secondary electron emission from the sample by applying a predetermined voltage to the sample through the leads; and generating an image of the secondary electron emission from the sample. An apparatus includes a sample holder for a scanning electron microscope having an electrical interconnect and leads on top of the sample holder electrically connected to the electrical interconnect; a power source and a controller connected to the electrical interconnect for applying voltage to the sample holder to control the secondary electron emission from a sample mounted on the sample holder; and a computer coupled to a secondary electron detector to generate images of the secondary electron emission from the sample.

  5. Development of a spectroscopic technique for simultaneous magnetic field, electron density, and temperature measurements in ICF-relevant plasmas

    Science.gov (United States)

    Dutra, E. C.; Koch, J. A.; Presura, R.; Angermeier, W. A.; Darling, T.; Haque, S.; Mancini, R. C.; Covington, A. M.

    2016-11-01

    Spectroscopic techniques in the visible range are often used in plasma experiments to measure B-field induced Zeeman splitting, electron densities via Stark broadening, and temperatures from Doppler broadening. However, when electron densities and temperatures are sufficiently high, the broadening of the Stark and Doppler components can dominate the emission spectra and obscure the Zeeman component. In this research, we are developing a time-resolved multi-axial technique for measuring the Zeeman, Stark, and Doppler broadened line emission of dense magnetized plasmas for Z-pinch and Dense Plasma Focus (DPF) accelerators. The line emission is used to calculate the electron densities, temperatures, and B-fields. In parallel, we are developing a line-shape modeling code that incorporates the broadening effects due to Stark, Doppler, and Zeeman effects for dense magnetized plasma. This manuscript presents the details of the experimental setup and line shape code, along with the results obtained from an Al iii doublet at the University of Nevada, Reno at Nevada Terawatt Facility. Future tests are planned to further evaluate the technique and modeling on other material wire array, gas puff, and DPF platforms.

  6. A simple measuring technique of surface flow velocity to analyze the behavior of velocity fields in hydraulic engineering applications.

    Science.gov (United States)

    Tellez, Jackson; Gomez, Manuel; Russo, Beniamino; Redondo, Jose M.

    2015-04-01

    An important achievement in hydraulic engineering is the proposal and development of new techniques for the measurement of field velocities in hydraulic problems. The technological advances in digital cameras with high resolution and high speed found in the market, and the advances in digital image processing techniques now provides a tremendous potential to measure and study the behavior of the water surface flows. This technique was applied at the Laboratory of Hydraulics at the Technical University of Catalonia - Barcelona Tech to study the 2D velocity fields in the vicinity of a grate inlet. We used a platform to test grate inlets capacity with dimensions of 5.5 m long and 4 m wide allowing a zone of useful study of 5.5m x 3m, where the width is similar of the urban road lane. The platform allows you to modify the longitudinal slopes from 0% to 10% and transversal slope from 0% to 4%. Flow rates can arrive to 200 l/s. In addition a high resolution camera with 1280 x 1024 pixels resolution with maximum speed of 488 frames per second was used. A novel technique using particle image velocimetry to measure surface flow velocities has been developed and validated with the experimental data from the grate inlets capacity. In this case, the proposed methodology can become a useful tools to understand the velocity fields of the flow approaching the inlet where the traditional measuring equipment have serious problems and limitations. References DigiFlow User Guide. (2012), (June). Russo, B., Gómez, M., & Tellez, J. (2013). Methodology to Estimate the Hydraulic Efficiency of Nontested Continuous Transverse Grates. Journal of Irrigation and Drainage Engineering, 139(10), 864-871. doi:10.1061/(ASCE)IR.1943-4774.0000625 Teresa Vila (1), Jackson Tellez (1), Jesus Maria Sanchez (2), Laura Sotillos (1), Margarita Diez (3, 1), and J., & (1), M. R. (2014). Diffusion in fractal wakes and convective thermoelectric flows. Geophysical Research Abstracts - EGU General Assembly 2014

  7. SVD-Based Technique for Interference Cancellation and Noise Reduction in NMR Measurement of Time-Dependent Magnetic Fields.

    Science.gov (United States)

    Chen, Wenjun; Ma, Hong; Yu, De; Zhang, Hua

    2016-03-04

    A nuclear magnetic resonance (NMR) experiment for measurement of time-dependent magnetic fields was introduced. To improve the signal-to-interference-plus-noise ratio (SINR) of NMR data, a new method for interference cancellation and noise reduction (ICNR) based on singular value decomposition (SVD) was proposed. The singular values corresponding to the radio frequency interference (RFI) signal were identified in terms of the correlation between the FID data and the reference data, and then the RFI and noise were suppressed by setting the corresponding singular values to zero. The validity of the algorithm was verified by processing the measured NMR data. The results indicated that, this method has a significantly suppression of RFI and random noise, and can well preserve the FID signal. At present, the major limitation of the proposed SVD-based ICNR technique is that the threshold value for interference cancellation needs to be manually selected. Finally, the inversion waveform of the applied alternating magnetic field was given by fitting the processed experimental data.

  8. A digital instantaneous frequency measurement technique utilising high speed analogue to digital converters and field programmable gate arrays

    CSIR Research Space (South Africa)

    Herselman, PLR

    2007-09-01

    Full Text Available In modern information and sensor systems, the timely estimation of the carrier frequency of received signals is of critical importance. This paper presents a digital instantaneous frequency measurement (DIFM) technique, which can measure the carrier...

  9. Process measuring techniques; Prozessmesstechnik

    Energy Technology Data Exchange (ETDEWEB)

    Freudenberger, A.

    2000-07-01

    This introduction into measurement techniques for chemical and process-technical plant in science and industry describes in detail the methods used to measure basic quantities. Most prominent are modern measuring techniques by means of ultrasound, microwaves and the Coriolis effect. Alongside physical and measuring technique fundamentals, the practical applications of measuring devices are described. Calculation examples are given to illustrate the subject matter. The book addresses students of physical engineering, process engineering and environmental engineering at technical schools as well as engineers of other disciplines wishing to familiarize themselves with the subject of process measurement techniques. (orig.) [German] Diese Einfuehrung in die Messtechnik fuer chemische und verfahrens-technische Forschungs- und Produktionsanlagen beschreibt ausfuehrlich die Methoden zur Messung der Basisgroessen. Moderne Messverfahren mit Ultraschall, Mikrowellen und Coriolis-Effekt stehen dabei im Vordergrund. Beruecksichtigung finden sowohl die physikalischen und messtechnischen Grundlagen als auch die praktischen Anwendungen der Geraete. Berechnungsbeispiele dienen der Erlaeuterung und Vertiefung des Stoffes. Angesprochen sind Studenten der Ingenieurstufengaenge Physikalische Technik und Verfahrens- und Umwelttechnik an Fachhochschulen als auch Ingenieure anderer Fachrichtungen, die sich in das Gebiet der Prozessmesstechnik einarbeiten wollen. (orig.)

  10. Application of the digital volume correlation technique for the measurement of displacement and strain fields in bone: a literature review.

    Science.gov (United States)

    Roberts, Bryant C; Perilli, Egon; Reynolds, Karen J

    2014-03-21

    Digital volume correlation (DVC) provides experimental measurements of displacements and strains throughout the interior of porous materials such as trabecular bone. It can provide full-field continuum- and tissue-level measurements, desirable for validation of finite element models, by comparing image volumes from subsequent µCT scans of a sample in unloaded and loaded states. Since the first application of DVC for measurement of strain in bone tissue, subsequent reports of its application to trabecular bone cores up to whole bones have appeared within the literature. An "optimal" set of procedures capable of precise and accurate measurements of strain, however, still remains unclear, and a systematic review focussing explicitly on the increasing number of DVC algorithms applied to bone or structurally similar materials is currently unavailable. This review investigates the effects of individual parameters reported within individual studies, allowing to make recommendations for suggesting algorithms capable of achieving high accuracy and precision in displacement and strain measurements. These recommendations suggest use of subsets that are sufficiently large to encompass unique datasets (e.g. subsets of 500 µm edge length when applied to human trabecular bone cores, such as cores 10mm in height and 5mm in diameter, scanned at 15 µm voxel size), a shape function that uses full affine transformations (translation, rotation, normal strain and shear strain), the robust normalized cross-correlation coefficient objective function, and high-order interpolation schemes. As these employ computationally burdensome algorithms, researchers need to determine whether they have the necessary computational resources or time to adopt such strategies. As each algorithm is suitable for parallel programming however, the adoption of high precision techniques may become more prevalent in the future.

  11. Remote field eddy current technique for gap measurement of horizontal flux detector guide tube in pressurized heavy water reactor

    Energy Technology Data Exchange (ETDEWEB)

    Lee, Dong Hoon; Jung, Hyun Kyu; Yang, Dong Ju; Cheong, Yong Moo [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

    2004-11-15

    The fuel channels including the pressure tube(PT) and the calandria tube(CT) are important components of the pressurized heavy water reactor(PHWR). A sagging of fuel channel increases by heat and radiation exposure with the increasing operation time. The contact of fuel channel to the Horizontal flux Detector(HFD) guide tube is needed for the power plant safety. In order to solve this safety issue, the electromagnetic technique was applied to measure the status of the guide tube. The Horizontal flux Detector(HFD) guide tube and the Calandria tube(CT) in the Pressurized Heavy Water Reactor(PHWR) are cross-aligned horizontally. The remote field eddy current(RFEC) technology is applied for gap measurement between the HFD guide tube and the CT HFD guide tube can be detected by inserting the RFEC probe into pressure tube(PT) at the crossing point directly. The RFEC signals using the volume integral method(VIM) were simulated for obtaining the optimal inspection parameters. This paper shows that the simulated eddy current signals and the experimental results in variance with the CT/HFD gap.

  12. Electromagnetic model of a near-field cable-free impedance and gain measurement technique for electrically small antennas

    DEFF Research Database (Denmark)

    Zhang, Jiaying; Pivnenko, Sergey; Breinbjerg, Olav

    2011-01-01

    the signal scattered by it when it is loaded in turn with three known loads. The determination of the antenna impedance and gain is formulated by using the spherical wave expansion technique. The advantages of this measurement technique are summarized as follows. First, the limited dynamic range problem...

  13. Measurements of the unsteady flow field within the stator row of a transonic axial-flow fan. 1: Measurement and analysis technique

    Science.gov (United States)

    Suder, K. L.; Hathaway, M. D.; Okiishi, T. H.; Strazisar, A. J.; Adamczyk, J. J.

    1987-01-01

    This two-part paper presents laser anemometer measurements of the unsteady velocity field within the stator row of a transonic axial-flow fan. The objective is to provide additional insight into unsteady blade-row interactions within high speed compressors which affect stage efficiency, energy transfer, and other design considerations. Part 1 describes the measurement and analysis techniques used for resolving the unsteady flow field features. The ensemble-average and variance of the measured velocities are used to identify the rotor wake generated and unresolved unsteadiness, respectively. (Rotor wake generated unsteadiness refers to the unsteadiness generated by the rotor wake velocity deficit and the term unresolved unsteadiness refers to all remaining contributions to unsteadiness such as vortex shedding, turbulence, mass flow fluctuations, etc.). A procedure for calculating auto and cross correlations of the rotor wake generated and unresolved unsteady velocity fluctuations is described. These unsteady-velocity correlations have significance since they also result from a decomposition of the Navier-Stokes equations. This decomposition of the Navier-Stokes equations resulting in the velocity correlations used to describe the unsteady velocity field will also be outlined in this paper.

  14. Measurements of the unsteady flow field within the stator row of a transonic axial-flow fan. I - Measurement and analysis technique

    Science.gov (United States)

    Suder, K. L.; Strazisar, A. J.; Adamczyk, J. J.; Hathaway, M. D.; Okiishi, T. H.

    1987-01-01

    This two-part paper presents laser anemometer measurements of the unsteady velocity field within the stator row of a transonic axial-flow fan. The objective is to provide additional insight into unsteady blade-row interactions within highspeed compressors which affect stage efficiency, energy transfer, and other design considerations. Part 1 describes the measurement and analysis techniques used for resolving the unsteady flow field features. The ensemble-average and variance of the measured velocities are used to identify the rotor wake generated and unresolved unsteadiness, respectively. (Rotor wake generated unsteadiness refers to the unsteadiness generated by the rotor wake velocity deficit and the term unresolved unsteadiness refers to all remaining contributions to unsteadiness such as vortex shedding, turbulence, mass flow fluctutions, etc.). A procedure for calculating auto and cross correlations of the rotor wake generated and unresolved unsteady velocity fluctuations is described. These unsteady-velocity correlations have significance since they also result from a decomposition of the Navier-Stokes equations. This decomposition of the Navier-Stokes equations resulting in the velocity correlations used to describe the unsteady velocity field will also be outlined in this paper.

  15. Ambient in-situ immersion freezing measurements - findings from the ZAMBIS 2014 field campaign for three ice nucleation techniques

    Science.gov (United States)

    Kohn, Monika; Atkinson, James D.; Lohmann, Ulrike; Kanji, Zamin A.

    2015-04-01

    To estimate the influence of clouds on the Earth's radiation budget, it is crucial to understand cloud formation processes in the atmosphere. A key process, which significantly affects cloud microphysical properties and the initiation of precipitation thus contributing to the hydrological cycle, is the prevailing type of ice nucleation mechanism. In mixed-phase clouds immersion freezing is the dominant ice crystal forming mechanism, whereby ice nucleating particles (INP) first act as cloud condensation nuclei (CCN) and are activated to cloud droplets followed by freezing upon supercooling. There are a number of experimental methods and techniques to investigate the ice nucleating ability in the immersion mode, however most techniques are offline for field sampling or only suitable for laboratory measurements. In-situ atmospheric studies are needed to understand the ice formation processes of 'real world' particles. Laboratory experiments simulate conditions of atmospheric processes like ageing or coating but are still idealized. Our method is able to measure ambient in-situ immersion freezing on single immersed aerosol particles. The instrumental setup consists of the recently developed portable immersion mode cooling chamber (PIMCA) as a vertical extension to the portable ice nucleation chamber (PINC, [1]), where the frozen fraction of activated aerosol particles are detected by the ice optical depolarization detector (IODE, [2]). Two additional immersion freezing techniques based on a droplet freezing array [3,4] are used to sample ambient aerosol particles either in a suspension (fraction larger ~0.6 μm) or on PM10-filters to compare different ice nucleation techniques. Here, we present ambient in-situ measurements at an urban forest site in Zurich, Switzerland held during the Zurich ambient immersion freezing study (ZAMBIS) in spring 2014. We investigated the ice nucleating ability of natural atmospheric aerosol with the PIMCA/PINC immersion freezing setup as

  16. Comparison of the FFT/matrix inversion and system matrix techniques for higher-order probe correction in spherical near-field antenna measurements

    DEFF Research Database (Denmark)

    Pivnenko, Sergey; Nielsen, Jeppe Majlund; Breinbjerg, Olav

    2011-01-01

    Two higher-order probe-correction techniques for spherical near-field antenna measurements are compared in details for the accuracy they provide and their computational cost. The investigated techniques are the FFT/matrix inversion and the system matrix inversion. Each of these techniques allows...... and a higher-order probe....... correction of general high-order probes, including non-symmetric dual-polarized antennas with independent ports. The investigation was carried out by processing with each technique the same measurement data for a challenging case with an antenna under test significantly offset from the center of rotation...

  17. Recent Advances in Antenna Measurement Techniques at the DTU-ESA Spherical Near-Field Antenna Test Facility

    DEFF Research Database (Denmark)

    Breinbjerg, Olav; Pivnenko, Sergey; Kim, Oleksiy S.

    2014-01-01

    This paper reports recent antenna measurement projects and research at the DTU-ESA Spherical Near-Field Antenna Test Facility at the Technical University of Denmark. High-accuracy measurement projects for the SMOS, SENTINEL-1, and BIOMASS missions of the European Space Agency were driven...... by uncertainty requirements of a few hundredths of dB for the directivity and correspondingly strong requirements for gain and/or phase. Research and development of 1:3 bandwidth range probes, and the near-field to far-field transformation algorithm accounting for the higher-order azimuthal modes...

  18. Measurement of the magnetic moment of the 2$^{+}$ state in neutron-rich radioactive $^{72,74}$Zn using the transient field technique in inverse kinematics

    CERN Multimedia

    Kruecken, R; Speidel, K; Voulot, D; Neyens, G; Gernhaeuser, R A; Fraile prieto, L M; Leske, J

    We propose to measure the sign and magnitude of the g-factors of the first 2$^{+}$ states in radioactive neutron-rich $^{72,74}$Zn applying the transient field (TF) technique in inverse kinematics. The result of this experiment will allow to probe the $\

  19. Atmospheric Ice Accretion Measurement Techniques

    Directory of Open Access Journals (Sweden)

    M Virk

    2016-09-01

    Full Text Available Atmospheric icing on structures has proven to be an area of concern in many cold climate geographical regions like arctic and alpine. Difficulties encountered by the communication, construction and power industries in these areas are the subject of intense investigations for researchers from decades. Three main methods of investigation are generally employed by researchers to study atmospheric ice accretion on structures: a continuous field measurements, b lab based simulations using icing wind tunnel & c numerical modelling. This paper presents a brief review study of various techniques to understand and measure the atmospheric ice accretion on structures, anti/de icing techniques and important parameters for numerical modelling of atmospheric ice accretion.

  20. Early detection of corrosion of reinforcement: Potential field measurement and galvano-static pulse technique. Frueherkennung von Bewehrungskorrosion: Potentialfeldmessung und galvanostatische Impulstechnik

    Energy Technology Data Exchange (ETDEWEB)

    Boehni, H.; Elsener, B. (ETH Zurich (Switzerland))

    1991-01-01

    Early detection of corrosion damage in reinforced concrete buildings is not only with regard to savety of great importance but also economically. Electrochemical methods largely comply with the requirements. The focus is put on potential field measurements as nondestructive method for locating corroded areas of reinforcement in theory and with concrete examples of application. Galvanostatic pulse techniques can be used as valuable complement to potential measurements. (BWI).

  1. Effects of the search technique on the measurement of the change in quality of randomized controlled trials over time in the field of brain injury

    Directory of Open Access Journals (Sweden)

    Yamada Chisa

    2005-02-01

    Full Text Available Abstract Background To determine if the search technique that is used to sample randomized controlled trial (RCT manuscripts from a field of medical science can influence the measurement of the change in quality over time in that field. Methods RCT manuscripts in the field of brain injury were identified using two readily-available search techniques: (1 a PubMed MEDLINE search, and (2 the Cochrane Injuries Group (CIG trials registry. Seven criteria of quality were assessed in each manuscript and related to the year-of-publication of the RCT manuscripts by regression analysis. Results No change in the frequency of reporting of any individual quality criterion was found in the sample of RCT manuscripts identified by the PubMed MEDLINE search. In the RCT manuscripts of the CIG trials registry, three of the seven criteria showed significant or near-significant increases over time. Conclusions We demonstrated that measuring the change in quality over time of a sample of RCT manuscripts from the field of brain injury can be greatly affected by the search technique. This poorly recognized factor may make measurements of the change in RCT quality over time within a given field of medical science unreliable.

  2. A measurement technique for hydroxyacetone

    Energy Technology Data Exchange (ETDEWEB)

    Klotz, P.J.

    1999-10-04

    Hydroxyacetone (HA) is mainly produced in the atmosphere from oxidation of hydrocarbons of the type, CH{sub 3}(R)C{double{underscore}bond}CH{sub 2}. Tuazon and Atkinson (1990) reported HA yield of 41% from the OH-initiated oxidation of methacrolein in the presence of NOx. Since methacrolein is a major product of isoprene oxidation (Carter and Atkinson, 1996), isoprene, a key biogenic hydrocarbon, is therefore expected to be an important source for HA. Consequently, knowledge of ambient concentration of HA would provide information needed to examine the applicability of isoprene reaction mechanisms developed in laboratory and to assess the contribution of isoprene to photooxidant production. The commonly used GC-FID technique involving cryo-focusing is unsuitable for HA owing to HA's thermal instability. When subjected to a temperature of 100 C for only a few seconds, HA was found to disappear completely. Since HA is highly soluble in water, the authors developed a wet chemical technique similar in principle to the one they reported earlier, namely, derivatization following liquid scrubbing. To increase the sensitivity, they adopted a fluorescence detection scheme based on o-phthaldialdehyde (OPA) chemistry. The technique was deployed in the field during two measurement periods at a NARSTO site located on Long Island, New York. The authors report the principle and the operation of this technique and the results obtained from these field studies.

  3. Three-dimensional two-component velocity measurement of the flow field induced by the Vorticella picta microorganism using a confocal microparticle image velocimetry technique.

    Science.gov (United States)

    Nagai, Moeto; Oishi, Masamichi; Oshima, Marie; Asai, Hiroshi; Fujita, Hiroyuki

    2009-03-26

    Understanding the biological feeding strategy and characteristics of a microorganism as an actuator requires the detailed and quantitative measurement of flow velocity and flow rate induced by the microorganism. Although some velocimetry methods have been applied to examine the flow, the measured dimensions were limited to at most two-dimensional two-component measurements. Here we have developed a method to measure three-dimensional two-component flow velocity fields generated by the microorganism Vorticella picta using a piezoscanner and a confocal microscope. We obtained the two-component velocities of the flow field in a two-dimensional plane denoted as the XY plane, with an observation area of 455x341 mum(2) and the resolution of 9.09 mum per each velocity vector by a confocal microparticle image velocimetry technique. The measurement of the flow field at each height took 37.5 ms, and it was repeated in 16 planes with a 2.50 mum separation in the Z direction. We reconstructed the three-dimensional two-component flow velocity field. From the reconstructed data, the flow velocity field [u((x,y,z)),v((x,y,z))] in an arbitrary plane can be visualized. The flow rates through YZ and ZX planes were also calculated. During feeding, we examined a suction flow to the mouth of the Vorticella picta and measured it to be to 300 pls.

  4. Measurements of the effectiveness of conservation agriculture at the field scale using radioisotopic techniques and runoff plots

    Science.gov (United States)

    Mabit, L.; Klik, A.; Toloza, A.; Benmansour, M.; Geisler, A.; Gerstmann, U. C.

    2009-04-01

    Growing evidence of the cost of soil erosion on agricultural land and off site impact of associated processes has emphasized the needs for quantitative assessment of erosion rates to develop and assess erosion control technology and to allocate conservation resources and development of conservation regulation, policies and programmes. Our main study goal was to assess the magnitude of deposition rates using Fallout Radionuclides ‘FRNs' (137-Cs and 210-Pb) and the mid-term (13 years) erosion rates using conventional runoff plot measurements in a small agricultural watershed under conventional and conservation tillage practices. The tillage treatments were conventional tillage system (CT), mechanical plough to 30 cm depth (the most common tillage system within the watershed); conservation tillage (CS) with cover crops during winter; and direct seeding (DS) no tillage with cover crops during winter. The experimental design - located in Mistelbach watershed 60 km north of Vienna/Austria - consists of one 3-metre-wide and 15-metre-long runoff plot (silt loam - slope of 14%) for each tillage system (CT, CS and DS) with the plots placed in the upper part of an agricultural field. 76 soil samples were collected to evaluate the initial fallout of 137-Cs and 210-Pb in a small forested area close to the experimental field, along a systematic multi-grid design,. In the sedimentation area of the watershed and down slope the agricultural field, 2 additional soil profiles were collected to 1 m depth. All soil samples were air dried, sieved to 2mm and analysed for their 137-Cs and 210-Pb contents using gamma detector. The main results and conclusion can be summarised as following: i) The initial 137-Cs fallout as measured in the 76 forested soil samples ranged from 1123 to 3354 Bq/m2 for an average of 1954 Bq/m2 with a coefficient of variation of 20.4 %. ii) Long-term erosion measurements (1994-2006) from runoff plots located in the upper part of the agricultural field just up

  5. Remote Attitude Measurement Techniques.

    Science.gov (United States)

    1982-12-01

    are other factors which will influence the selection of the communications means. One major factor is the selection of the technology to be used. Aside...electrooptical devices with partitioned focal planes, and the char- acteristics of these techniques influence how the focal planes are partitioned. G. FOCAL...a televison camera). The incident illumination produces a non-uniformity on the scanned side of the sensitive material which can be modeled as an

  6. A MEASUREMENT TECHNIQUE FOR HYDROXYACETONE.

    Energy Technology Data Exchange (ETDEWEB)

    KLOTZ,P.J.

    1999-10-04

    Hydroxyacetone (HA) is mainly produced in the atmosphere from oxidation of hydrocarbons of the type, CH{sub 3}(R)C=CH{sub 2}. Tuazon and Atkinson (1990) reported HA yield of 41% from the OH-initiated oxidation of methacrolein in the presence of NO{sub x}. Since methacrolein is a major product of isoprene oxidation (Carter and Atkinson, 1996), isoprene, a key biogenic hydrocarbon, is therefore expected to be an important source for HA. Consequently, knowledge of ambient concentration of HA would provide information needed to examine the applicability of isoprene reaction mechanisms developed in laboratory and to assess the contribution of isoprene to photooxidant production. The commonly used GC-FID technique involving cryo-focusing is unsuitable for HA owing to HA's thermal instability. When subjected to a temperature of 100 C for only a few seconds, HA was found to disappear completely. Since HA is highly soluble in water (it's Henry's law constant being {approx}2 x 10{sup 4} M atm{sup -1} at 20 C, Zhou and Lee, unpublished data), we developed a wet chemical technique similar in principle to the one we reported earlier (Lee and Zhou, 1993), namely, based on derivatization following liquid scrubbing. To increase the sensitivity, we adopted a fluorescence detection scheme based on o-phthaldialdehyde (OPA) chemistry. The technique was deployed in the field during two measurement periods at a NARSTO site located on Long Island (LI), New York. We report the principle and the operation of this technique and the results obtained from these field studies.

  7. Advanced in-flight measurement techniques

    CERN Document Server

    Lawson, Nicholas; Jentink, Henk; Kompenhans, Jürgen

    2013-01-01

    The book presents a synopsis of the main results achieved during the 3 year EU-project "Advanced Inflight Measurement Techniques (AIM)" which applied advanced image based measurement techniques to industrial flight testing. The book is intended to be not only an overview on the AIM activities but also a guide on the application of advanced optical measurement techniques for future flight testing. Furthermore it is a useful guide for engineers in the field of experimental methods and flight testing who face the challenge of a future requirement for the development of highly accurate non-intrusive in-flight measurement techniques.

  8. Multi-scale full-field measurements and near-wall modeling of turbulent subcooled boiling flow using innovative experimental techniques

    Energy Technology Data Exchange (ETDEWEB)

    Hassan, Yassin A., E-mail: y-hassan@tamu.edu

    2016-04-01

    Highlights: • Near wall full-field velocity components under subcooled boiling were measured. • Simultaneous shadowgraphy, infrared thermometry wall temperature and particle-tracking velocimetry techniques were combined. • Near wall velocity modifications under subcooling boiling were observed. - Abstract: Multi-phase flows are one of the challenges on which the CFD simulation community has been working extensively with a relatively low success. The phenomena associated behind the momentum and heat transfer mechanisms associated to multi-phase flows are highly complex requiring resolving simultaneously for multiple scales on time and space. Part of the reasons behind the low predictive capability of CFD when studying multi-phase flows, is the scarcity of CFD-grade experimental data for validation. The complexity of the phenomena and its sensitivity to small sources of perturbations makes its measurements a difficult task. Non-intrusive and innovative measuring techniques are required to accurately measure multi-phase flow parameters while at the same time satisfying the high resolution required to validate CFD simulations. In this context, this work explores the feasible implementation of innovative measuring techniques that can provide whole-field and multi-scale measurements of two-phase flow turbulence, heat transfer, and boiling parameters. To this end, three visualization techniques are simultaneously implemented to study subcooled boiling flow through a vertical rectangular channel with a single heated wall. These techniques are listed next and are used as follow: (1) High-speed infrared thermometry (IR-T) is used to study the impact of the boiling level on the heat transfer coefficients at the heated wall, (2) Particle Tracking Velocimetry (PTV) is used to analyze the influence that boiling parameters have on the liquid phase turbulence statistics, (3) High-speed shadowgraphy with LED illumination is used to obtain the gas phase dynamics. To account

  9. Helium II level measurement techniques

    Science.gov (United States)

    Celik, D.; Hilton, D. K.; Zhang, T.; Van Sciver, S. W.

    2001-05-01

    In this paper, a survey of cryogenic liquid level measurement techniques applicable to superfluid helium (He II) is given. The survey includes both continuous and discrete measurement techniques. A number of different probes and controlling circuits for this purpose have been described in the literature. They fall into one of the following categories: capacitive liquid level gauges, superconducting wire liquid level gauges, thermodynamic (heat transfer-based) liquid level gauges, resistive gauges, ultrasound and transmission line-based level detectors. The present paper reviews these techniques and their suitability for He II service. In addition to these methods, techniques for measuring the total liquid volume and mass gauging are also discussed.

  10. Optical pulses, lasers, measuring techniques

    CERN Document Server

    Früngel, Frank B A

    1965-01-01

    High Speed Pulse Technology: Volume II: Optical Pulses - Lasers - Measuring Techniques focuses on the theoretical and engineering problems that result from the capacitor discharge technique.This book is organized into three main topics: light flash production from a capacitive energy storage; signal transmission and ranging systems by capacitor discharges and lasers; and impulse measuring technique. This text specifically discusses the air spark under atmospheric conditions, industrial equipment for laser flashing, and claims for light transmitting system. The application of light impulse sign

  11. EXTRAPOLATION TECHNIQUES EVALUATING 24 HOURS OF AVERAGE ELECTROMAGNETIC FIELD EMITTED BY RADIO BASE STATION INSTALLATIONS: SPECTRUM ANALYZER MEASUREMENTS OF LTE AND UMTS SIGNALS.

    Science.gov (United States)

    Mossetti, Stefano; de Bartolo, Daniela; Veronese, Ivan; Cantone, Marie Claire; Cosenza, Cristina; Nava, Elisa

    2016-12-01

    International and national organizations have formulated guidelines establishing limits for occupational and residential electromagnetic field (EMF) exposure at high-frequency fields. Italian legislation fixed 20 V/m as a limit for public protection from exposure to EMFs in the frequency range 0.1 MHz-3 GHz and 6 V/m as a reference level. Recently, the law was changed and the reference level must now be evaluated as the 24-hour average value, instead of the previous highest 6 minutes in a day. The law refers to a technical guide (CEI 211-7/E published in 2013) for the extrapolation techniques that public authorities have to use when assessing exposure for compliance with limits. In this work, we present measurements carried out with a vectorial spectrum analyzer to identify technical critical aspects in these extrapolation techniques, when applied to UMTS and LTE signals. We focused also on finding a good balance between statistically significant values and logistic managements in control activity, as the signal trend in situ is not known. Measurements were repeated several times over several months and for different mobile companies. The outcome presented in this article allowed us to evaluate the reliability of the extrapolation results obtained and to have a starting point for defining operating procedures.

  12. Measuring soccer technique with easy-to-administer field tasks in female soccer players from four different competitive levels.

    Science.gov (United States)

    Pedersen, Arve Vorland; Lorås, Håvard; Norvang, Ole Petter; Asplund, Jennifer

    2014-12-01

    Soccer is a multidimensional sport that requires skills in many different domains. Reports from competitions at the highest levels around the world suggest that a particularly decisive performance factor is a team's technical execution. Testing of technical skills in soccer has been infrequent compared with testing of physiological variables, and there has been a lack of consensus as to which tasks should be included in test batteries. In this study, the validity of four field tasks (heading, long pass, juggling, and hit-the-post) was examined by testing 108 female soccer players from four different competitive levels, representing a hierarchy of skill levels. Correlation analysis indicated that the tasks' results appeared statistically unrelated (Spearman's ρ ≤ .36). Statistical comparisons across competitive levels showed that task performance was closely correlated with players' competition level, with regression analysis indicating that 92% of the variance in mean rankings across tasks could be explained by competitive level. As the easily administered and low-cost tasks identified differences in technical skills across competitive levels, such tasks appear valid for inclusion in tests of technical skills.

  13. Thermal measurements and inverse techniques

    CERN Document Server

    Orlande, Helcio RB; Maillet, Denis; Cotta, Renato M

    2011-01-01

    With its uncommon presentation of instructional material regarding mathematical modeling, measurements, and solution of inverse problems, Thermal Measurements and Inverse Techniques is a one-stop reference for those dealing with various aspects of heat transfer. Progress in mathematical modeling of complex industrial and environmental systems has enabled numerical simulations of most physical phenomena. In addition, recent advances in thermal instrumentation and heat transfer modeling have improved experimental procedures and indirect measurements for heat transfer research of both natural phe

  14. Field techniques for sampling ants

    Science.gov (United States)

    Ants occur in most environments and ecologists ask a diverse array of questions involving ants. Thus, a key consideration in ant studies is to match the environment and question (and associated environmental variables) to the ant sampling technique. Since each technique has distinct limitations, usi...

  15. Optical measurement techniques - A push for digitization

    Science.gov (United States)

    Kulkarni, Rishikesh; Rastogi, Pramod

    2016-12-01

    Over the years, optical measurement techniques have been the problem-solving backbone of many engineering applications such as nondestructive testing of materials, measurement of various material properties, structural analysis and experimental mechanics [1-3]. Probably the most important advantage associated with any optical measurement system over other systems is its non-contact type of measurement capability. Apart from their non-contact nature, the optical measurement systems are capable of providing full-field measurements at scales ranging from milli-meters to nano-meters.

  16. Image processing techniques revealing the relationship between the field-measured ambient gamma dose equivalent rate and geological conditions at a granitic area, Velence Mountains, Hungary

    Science.gov (United States)

    Beltran Torres, Silvana; Petrik, Attila; Zsuzsanna Szabó, Katalin; Jordan, Gyozo; Szabó, Csaba

    2017-04-01

    In order to estimate the annual dose that the public receive from natural radioactivity, the identification of the potential risk areas is required which, in turn, necessitates understanding the relationship between the spatial distribution of natural radioactivity and the geogenic risk factors (e.g., rock types, dykes, faults, soil conditions, etc.). A detailed spatial analysis of ambient gamma dose equivalent rate was performed in the western side of Velence Mountains, the largest outcropped granitic area in Hungary. In order to assess the role of local geology in the spatial distribution of ambient gamma dose rates, field measurements were carried out at ground level at 300 sites along a 250 m x 250 m regular grid in a total surface of 14.7 km2. Digital image processing methods were applied to identify anomalies, heterogeneities and spatial patterns in the measured gamma dose rates, including local maxima and minima determination, digital cross sections, gradient magnitude and gradient direction, second derivative profile curvature, local variability, lineament density, 2D autocorrelation and directional variogram analyses. Statistical inference showed that different gamma dose rate levels are associated with the rock types (i.e., Carboniferous granite, Pleistocene colluvial, proluvial, deluvial sediments and talus, and Pannonian sand and pebble), with the highest level on the Carboniferous granite including outlying values. Moreover, digital image processing revealed that linear gamma dose rate spatial features are parallel to the SW-NE dyke system and possibly to the NW-SE main fractures. The results of this study underline the importance of understanding the role of geogenic risk factors influencing the ambient gamma dose rate received by public. The study also demonstrates the power of the image processing techniques for the identification of spatial pattern in field-measured geogenic radiation.

  17. The National Fuel End-Use Efficiency Field Test: Energy Savings and Performance of an Improved Energy Conservation Measure Selection Technique

    Energy Technology Data Exchange (ETDEWEB)

    Ternes, M.P.

    1991-01-01

    The performance of an advanced residential energy conservation measure (ECM) selection technique was tested in Buffalo, New York, to verify the energy savings and program improvements achieved from use of the technique in conservation programs and provide input into determining whether utility investments in residential gas end-use conservation are cost effective. The technique analyzes a house to identify all ECMs that are cost effective in the building envelope, space-heating system, and water-heating system. The benefit-to-cost ratio (BCR) for each ECM is determined and cost-effective ECMs (BCR > 1.0) are selected once interactions between ECMs are taken into account. Eighty-nine houses with the following characteristics were monitored for the duration of the field test: occupants were low-income, houses were single-family detached houses but not mobile homes, and primary space- and water-heating systems were gas-fired. Forty-five houses received a mix of ECMs as selected by the measure selection technique (audit houses) and 44 served as a control group. Pre-weatherization data were collected from January to April 1988 and post-weatherization data were collected from December 1988 to April 1989. Space- and waterheating gas consumption and indoor temperature were monitored weekly during the two winters. A house energy consumption model and regression analysis were employed to normalize the space-heating energy savings to average outdoor temperature conditions and a 68 F indoor temperature. Space and water-heating energy savings for the audit houses were adjusted by the savings for the control houses. The average savings of 257 therms/year for the audit houses was 17% of the average pre-weatherization house gas consumption and 78% of that predicted. Average space-heating energy savings was 252 therms/year (25% of pre-weatherization space-heating energy consumption and 85% of the predicted value) and average water-heating savings was 5 therms/year (2% of pre

  18. A simplified technique for determining the rotational motion of a satellite based on the onboard measurements of the angular velocity and magnetic field of the Earth

    Science.gov (United States)

    Abrashkin, V. I.; Voronov, K. E.; Piyakov, I. V.; Puzin, Yu. Ya.; Sazonov, V. V.; Syomkin, N. D.; Chebukov, S. Yu.

    2016-09-01

    The mathematical model, which allowed us to reconstruct the rotational motion of the Bion M-1 and Foton M-4 satellites by processing the measurements of onboard magnetometers and the angular velocity sensor, is sufficiently detailed and accurate. If we slightly lower the requirements for accuracy and transfer to a rougher model, i.e., we will not update the biases in measurements of the angular velocity component, then the measurement processing technique can be significantly simplified. The volume of calculations in minimizing the functional of the least-square technique is reduced; the most complicated part of calculations is performed using the standard procedure of computational linear algebra. This simplified technique is described below, and the examples of its application for reconstructing the rotational motion of the Foton M-4 satellite are presented. A noticeable distinction in the reconstructions of motion, constructed by simplified and more exact techniques, is revealed in processing the measurements over time intervals longer than 4 hours.

  19. Developments in luminescence measurement techniques

    DEFF Research Database (Denmark)

    Thomsen, Kristina Jørkov; Bøtter-Jensen, L.; Denby, Phil M.

    2006-01-01

    We report on our continuing investigation and development of new measurement facilities for use in irradiation, optical stimulation and luminescence signal detection; these facilities have potential application to all forms of luminescence-based retrospective dosimetry, and are particularly...... intended for use with the Riso TL/OSL reader. We have investigated the potential of new more powerful blue (455 nm) and green (530nm) LEDs, and of gated counting combined with pulsed stimulation light techniques using conventional LEDs. Measurement of time-resolved OSL has resulted in a method of real......; both types are very stable and reproducible. Other recent developments include the modification of a Riso reader to measure both thermally and optically stimulated electrons (TSE and OSE) from granular or chip phosphors. (c) 2006 Elsevier Ltd. All rights reserved....

  20. Ionospheric Measurements Using Environmental Sampling Techniques

    Science.gov (United States)

    Bourdeau, R. E.; Jackson, J. E.; Kane, J. A.; Serbu, G. P.

    1960-01-01

    Two rockets were flown to peak altitudes of 220 km in September 1959 to test various methods planned for future measurements of ionization parameters in the ionosphere, exosphere, and interplanetary plasma. The experiments used techniques which sample the ambient environment in the immediate vicinity of the research vehicle. Direct methods were chosen since indirect propagation techniques do not provide the temperatures of charged particles, are insensitive to ion densities, and cannot measure local electron densities under all conditions. Very encouraging results have been obtained from a preliminary analysis of data provided by one of the two flights. A new rf probe technique was successfully used to determine the electron density profile. This was indicated by its agreement with the results of a companion cw propagation experiment, particularly when the probe data were corrected for the effects of the ion sheath which surrounds the vehicle. The characteristics of this sheath were determined directly in flight by an electric field meter which provided the sheath field, and by a Langmuir probe which measured the total potential across the sheath. The electron temperatures deduced from the Langmuir probe data are greater than the neutral gas temperatures previously measured for the same location and season, but these measurements possibly were taken under different atmospheric conditions. Ion densities were calculated from the ion trap data for several altitudes ranging from 130 to 210 km and were found to be within 20 percent of the measured electron densities.

  1. Antenna Diagnostics using Near Field Techniques

    NARCIS (Netherlands)

    Paquay, M.H.A.

    1996-01-01

    The radiation characteristics of an antenna are fully determined by its aperture distribution. Measured Near Field data gives an impression but this is not good enough to detect small anomalies. For good antenna diagnostics, the field at the aperture plane is required. The Near Field Measurement Tec

  2. A review on creatinine measurement techniques.

    Science.gov (United States)

    Mohabbati-Kalejahi, Elham; Azimirad, Vahid; Bahrami, Manouchehr; Ganbari, Ahmad

    2012-08-15

    This paper reviews the entire recent global tendency for creatinine measurement. Creatinine biosensors involve complex relationships between biology and micro-mechatronics to which the blood is subjected. Comparison between new and old methods shows that new techniques (e.g. Molecular Imprinted Polymers based algorithms) are better than old methods (e.g. Elisa) in terms of stability and linear range. All methods and their details for serum, plasma, urine and blood samples are surveyed. They are categorized into five main algorithms: optical, electrochemical, impedometrical, Ion Selective Field-Effect Transistor (ISFET) based technique and chromatography. Response time, detection limit, linear range and selectivity of reported sensors are discussed. Potentiometric measurement technique has the lowest response time of 4-10 s and the lowest detection limit of 0.28 nmol L(-1) belongs to chromatographic technique. Comparison between various techniques of measurements indicates that the best selectivity belongs to MIP based and chromatographic techniques. Copyright © 2012 Elsevier B.V. All rights reserved.

  3. Calibration and validation of full-field techniques

    Directory of Open Access Journals (Sweden)

    Thalmann R.

    2010-06-01

    Full Text Available We review basic metrological terms related to the use of measurement equipment for verification of numerical model calculations. We address three challenges that are faced when performing measurements in experimental mechanics with optical techniques: the calibration of a measuring instrument that (i measures strain values, (ii provides full-field data, and (iii is dynamic.

  4. Improved modeling techniques for turbomachinery flow fields

    Energy Technology Data Exchange (ETDEWEB)

    Lakshminarayana, B. [Pennsylvania State Univ., University Park, PA (United States); Fagan, J.R. Jr. [Allison Engine Company, Indianapolis, IN (United States)

    1995-10-01

    This program has the objective of developing an improved methodology for modeling turbomachinery flow fields, including the prediction of losses and efficiency. Specifically, the program addresses the treatment of the mixing stress tensor terms attributed to deterministic flow field mechanisms required in steady-state Computational Fluid Dynamic (CFD) models for turbo-machinery flow fields. These mixing stress tensors arise due to spatial and temporal fluctuations (in an absolute frame of reference) caused by rotor-stator interaction due to various blade rows and by blade-to-blade variation of flow properties. These tasks include the acquisition of previously unavailable experimental data in a high-speed turbomachinery environment, the use of advanced techniques to analyze the data, and the development of a methodology to treat the deterministic component of the mixing stress tensor. Penn State will lead the effort to make direct measurements of the momentum and thermal mixing stress tensors in high-speed multistage compressor flow field in the turbomachinery laboratory at Penn State. They will also process the data by both conventional and conditional spectrum analysis to derive momentum and thermal mixing stress tensors due to blade-to-blade periodic and aperiodic components, revolution periodic and aperiodic components arising from various blade rows and non-deterministic (which includes random components) correlations. The modeling results from this program will be publicly available and generally applicable to steady-state Navier-Stokes solvers used for turbomachinery component (compressor or turbine) flow field predictions. These models will lead to improved methodology, including loss and efficiency prediction, for the design of high-efficiency turbomachinery and drastically reduce the time required for the design and development cycle of turbomachinery.

  5. POSIVA groundwater flow measuring techniques

    Energy Technology Data Exchange (ETDEWEB)

    Oehberg, A. [Saanio and Riekkola Consulting Engineers, Helsinki (Finland); Rouhiainen, P. [PRG-Tec Oy (Finland)

    2000-08-01

    Posiva Oy has carried out site characterisation for the final disposal of spent nuclear fuel in Finland since 1987. To meet the demanding needs to measure the hydraulic parameters in bedrock Posiva launched development of new flowmeter techniques including measuring methods and equipment in co-operation with PRG-Tec Oy. The techniques have been tested and used in the ongoing site investigations in Finland, in the underground Hard Rock Laboratory (HRL) at Aespoe in Sweden and in URL in Canada. The new methods are called difference flow and transverse flow methods. The difference flow method includes two modes, normal and detailed flow logging methods. In the normal mode the flow rate measurement is based on thermal pulse and thermal dilution methods, in the detailed logging mode only on thermal dilution method. The measuring ranges for flow rate with thermal pulse and dilution methods are 0.1-10 ml/min and 2-5000 ml/min, respectively. The difference flow method(normal mode) for small flows (0.1-10 ml/min) is based on measuring the pulse transit time and direction of a thermal pulse in the sensor. For high flows (2-5000 ml/min) the method is based on thermal dilution rate of a sensor. Direction is measured with monitoring thermistors. Inflow or outflow in the test interval is created due to natural or by pumping induced differences between heads in the borehole water and groundwater around the borehole. The single point resistance (and the temperature of borehole water) measurement is carried out simultaneously with the difference flow measurements, both in normal and detailed flow logging modes, while the tool is moving. The result is utilised for checking the exact depth of the tool. As the result a continuous log is obtained from which single fractures can be detected. The transverse flowmeter is able to measure the groundwater flow across a borehole. A special packer system guides the flow through the flow sensors. Four inflatable seals between conventional

  6. FIELD STRENGTH MEASUREMENTS, PHASE II.

    Science.gov (United States)

    The measurement of the strength of radio frequency fields at high frequency and above has followed practices which are standard for the measurement...of field strength at medium and low frequencies. Variability of measurements made in practical situations and a lack of reproducibility of...measurements made under apparently identical conditions has prompted an investigation of equipment and methods used in the determinations. The field strength

  7. Absolute technique for measuring internal electric fields in InGaN/GaN light-emitting diodes by electroreflectance applicable to all crystal orientations

    Science.gov (United States)

    Tanikawa, Tomoyuki; Shojiki, Kanako; Katayama, Ryuji; Kuboya, Shigeyuki; Matsuoka, Takashi; Honda, Yoshio; Amano, Hiroshi

    2017-08-01

    The internal electric fields in III-polar (0001), N-polar (000\\bar{1}), and semipolar (10\\bar{1}1) InGaN/GaN light-emitting diodes were investigated by electroreflectance (ER) spectroscopy. The ER spectra reflected the difference in the direction and strength of internal electric fields. Phase analyses of the ER signal revealed that only III-polar InGaN wells have the opposite direction of the internal electric field at zero bias voltage; this finding is in good agreement with the results of numerical analyses. Quantitative analyses of internal electric fields were conducted by the linewidth analyses of ER spectra. Our experimental results indicate that the absolute value of internal electric fields can be measured from ER spectra.

  8. Gravity field determination and error assessment techniques

    Science.gov (United States)

    Yuan, D. N.; Shum, C. K.; Tapley, B. D.

    1989-01-01

    Linear estimation theory, along with a new technique to compute relative data weights, was applied to the determination of the Earth's geopotential field and other geophysical model parameters using a combination of satellite ground-based tracking data, satellite altimetry data, and the surface gravimetry data. The relative data weights for the inhomogeneous data sets are estimated simultaneously with the gravity field and other geophysical and orbit parameters in a least squares approach to produce the University of Texas gravity field models. New techniques to perform calibration of the formal covariance matrix for the geopotential solution were developed to obtain a reliable gravity field error estimate. Different techniques, which include orbit residual analysis, surface gravity anomaly residual analysis, subset gravity solution comparisons and consider covariance analysis, were applied to investigate the reliability of the calibration.

  9. An acoustic mode measurement technique

    Science.gov (United States)

    Joppa, P. D.

    1984-10-01

    Turbomachinery noise propagates in aircraft jet engine ducts in a complicated manner. Measurement of this propagation is useful both to identify source mechanisms and to design efficient linings. A practical method of making these measurements has been developed, using linear arrays of equally spaced microphones mounted flush with the duct wall. Circumferential or axial arrays are analyzed by spatial Fourier transform, giving sound level as a function of spinning order or axial wavenumber respectively. Complex demodulation is used to acquire data in a modest bandwidth around a high frequency of interest. A joint NASA/Boeing test of the system used 32 microphones in a JT15D turbofan engine inlet. A 400-Hz bandwidth centered at blade passage frequency and at half blade passage frequency was studied. The theoretically predicted modes were clearly seen at blade passage frequency; broadband noise at half blade passage frequency was biased towards modes corotating with the fan. Interference between similar modes was not a significant problem. A lining design study indicated a 15 percent improvement in lining efficiency was possible when mode data were used, for this particular engine. The technique has proven reliable and useful for source diagnostics and lining design.

  10. Pulsed thrust measurements using electromagnetic calibration techniques

    Energy Technology Data Exchange (ETDEWEB)

    Tang Haibin; Shi Chenbo; Zhang Xin' ai; Zhang Zun; Cheng Jiao [School of Astronautics, Beijing University of Aeronautics and Astronautics, Beijing 100191 (China)

    2011-03-15

    A thrust stand for accurately measuring impulse bits, which ranged from 10-1000 {mu}N s using a noncontact electromagnetic calibration technique is described. In particular, a permanent magnet structure was designed to produce a uniform magnetic field, and a multiturn coil was made to produce a calibration force less than 10 mN. The electromagnetic calibration force for pulsed thrust measurements was linear to the coil current and changed less than 2.5% when the distance between the coil and magnet changed 6 mm. A pulsed plasma thruster was first tested on the thrust stand, and afterward five single impulse bits were measured to give a 310 {mu}N s average impulse bit. Uncertainty of the measured impulse bit was analyzed to evaluate the quality of the measurement and was found to be 10 {mu}N s with 95% credibility.

  11. FIELD STRENGTH MEASUREMENTS, PHASE I.

    Science.gov (United States)

    The program included the testing and evaluation of commercial and military field- strength meters. It also included a study of the interpretation of...field- strength measurement data taken under multipath conditions. As part of the field- strength meter evaluation, five instruments, the AN/TRM-7, NF...interpretation of the measured data is the variability of field- strength values obtained over an area. Such variability is caused by the presence of multipath

  12. ac transmission line field measurements

    Energy Technology Data Exchange (ETDEWEB)

    Kotter, F.R.; Misakian, M.

    1977-11-01

    The concern in recent years over the environmental effects of electric and magnetic fields from high voltage transmission lines has also focused attention on the accuracy of measurements of these fields. Electric field meters are discussed in terms of theory of operation, parameters affecting performance, meter performance under field and laboratory conditions, and calibration procedures. The performance and calibration of magnetic field meters is described. (LCL)

  13. Investigating High Field Gravity using Astrophysical Techniques

    Energy Technology Data Exchange (ETDEWEB)

    Bloom, Elliott D.; /SLAC

    2008-02-01

    The purpose of these lectures is to introduce particle physicists to astrophysical techniques. These techniques can help us understand certain phenomena important to particle physics that are currently impossible to address using standard particle physics experimental techniques. As the subject matter is vast, compromises are necessary in order to convey the central ideas to the reader. Many general references are included for those who want to learn more. The paragraphs below elaborate on the structure of these lectures. I hope this discussion will clarify my motivation and make the lectures easier to follow. The lectures begin with a brief review of more theoretical ideas. First, elements of general relativity are reviewed, concentrating on those aspects that are needed to understand compact stellar objects (white dwarf stars, neutron stars, and black holes). I then review the equations of state of these objects, concentrating on the simplest standard models from astrophysics. After these mathematical preliminaries, Sec. 2(c) discusses 'The End State of Stars'. Most of this section also uses the simplest standard models. However, as these lectures are for particle physicists, I also discuss some of the more recent approaches to the equation of state of very dense compact objects. These particle-physics-motivated equations of state can dramatically change how we view the formation of black holes. Section 3 focuses on the properties of the objects that we want to characterize and measure. X-ray binary systems and Active Galactic Nuclei (AGN) are stressed because the lectures center on understanding very dense stellar objects, black hole candidates (BHCs), and their accompanying high gravitational fields. The use of x-ray timing and gamma-ray experiments is also introduced in this section. Sections 4 and 5 review information from x-ray and gamma-ray experiments. These sections also discuss the current state of the art in x-ray and gamma-ray satellite

  14. Dark field electron holography for strain measurement

    Energy Technology Data Exchange (ETDEWEB)

    Beche, A., E-mail: armand.beche@fei.com [CEA-Grenoble, INAC/SP2M/LEMMA, F-38054 Grenoble (France); Rouviere, J.L. [CEA-Grenoble, INAC/SP2M/LEMMA, F-38054 Grenoble (France); Barnes, J.P.; Cooper, D. [CEA-LETI, Minatec Campus, F-38054 Grenoble (France)

    2011-02-15

    Dark field electron holography is a new TEM-based technique for measuring strain with nanometer scale resolution. Here we present the procedure to align a transmission electron microscope and obtain dark field holograms as well as the theoretical background necessary to reconstruct strain maps from holograms. A series of experimental parameters such as biprism voltage, sample thickness, exposure time, tilt angle and choice of diffracted beam are then investigated on a silicon-germanium layer epitaxially embedded in a silicon matrix in order to obtain optimal dark field holograms over a large field of view with good spatial resolution and strain sensitivity. -- Research Highlights: {yields} Step by step explanation of the dark field electron holography technique. {yields} Presentation of the theoretical equations to obtain quantitative strain map. {yields} Description of experimental parameters influencing dark field holography results. {yields} Quantitative strain measurement on a SiGe layer embedded in a silicon matrix.

  15. A New Technique For Measuring The Twist Of Photospheric Active Regions Without Recourse To The Force-Free-Field Equation: Reconfirming The Hemispheric Helicity Trend

    Science.gov (United States)

    Nandy, Dibyendu; Calhoun, A.; Windschitl, J.; Canfield, R. C.; Linton, M. G.

    2007-05-01

    The twist component of magnetic helicity in solar active regions is known to be an important indicator of sub-photospheric flux tube dynamics and solar eruptive activity. Traditionally, estimates of the parameter alpha -- appearing in the force-free-field equation -- has been used to infer the twist of photospheric active regions. However, the photosphere is not force-free and this has lead to recent concerns on the validity of using the alpha parameter for determining photospheric active region twist. We have devised a new flux-tube-fitting technique for determining the twist of active regions without recourse to the force-free-field equation. This method assumes that the underlying active region flux system is cylindrically symmetric and uniformly twisted. By using this new technique, on a statistically compelling number of photospheric active region vector magnetograms, we re-confirm the hemispheric helicity rule independent of the force-free-field assumption. This research has been supported in parts by a NASA Living With a Star grant NNG05GE47G. A.C. and J.W. were supported by a NSF Research Experience for Undergraduates grant ATM-0243923 to Montana State University. M.G.L. acknowledges support from NASA and the Office of Naval Research.

  16. Path Integral Techniques in Conformal Field Theory

    CERN Document Server

    Van Tonder, A J

    2004-01-01

    We present the theory of a two-dimensional conformal scalar field using path integral techniques. We derive the conformal anomaly using an adaptation of the method of Fujikawa, and compare the result with a derivation based on a Pauli-Villars measure, where the anomaly is shifted from the path integral measure to the energy-momentum trace. In the path integral approach the energy-momentum is a true coordinate-invariant tensor quantity, and we explain how it is related to the corresponding non-tensor object arising in the operator approach, obtaining an intuitive explanation within the context of the path integral approach for the anomalous transformation law and anomalous Ward identities of the latter. After carefully calculating nontrivial contact terms arising in certain energy-momentum products, we use these to provide a simple consistency check confirming the change of variables formula for the path integral and to review the relationship between the conformal anomaly and the energy-momentum two-point fun...

  17. Unsteady measurement techniques for turbomachinery flows

    Science.gov (United States)

    Jaffa, Nicholas Andrew

    Accurate unsteady measurements are required for studying the flows in high speed turbomachines, which rely on the interaction between rotating and stationary components. Using statistics of phase locked ensembles simplifies the problem, but accurate frequency response in the 10-100 kHz range significantly limits the applicable techniques. This research advances the state of the art for phase resolved measurement techniques using for high speed turbomachinery flows focusing on the following areas: development, validation, and uncertainty quantification. Four methods were developed and implemented: an unsteady total pressure probe, the multiple overheat hot-wire method, the slanted hot-wire method, and the phase peak yaw hot-wire method. These methods allow for the entire phase locked average flow field to be measured (temperature, pressure, and velocity components, swirl angle, etc.). No trusted reference measurement or representative canonical flow exists for comparison of the phase resolved quantities, making validation challenging. Five different validation exercises were performed to increase the confidence and explore the range of applicability. These exercises relied on checking for consistency with expected flow features, comparing independent measurements, and cross validation with CFD. The combined uncertainties for the measurements were quantified using uncertainty estimates from investigations into the elemental error sources. The frequency response uncertainty of constant temperature hot-wire system was investigated using a novel method of illuminating the wire with a laser pulse. The uncertainty analysis provided estimates for the uncertainty in the measurements as well as showing the sensitivity to various sources of error.

  18. Electromagnetic Scattered Field Evaluation and Data Compression Using Imaging Techniques

    Science.gov (United States)

    Gupta, I. J.; Burnside, W. D.

    1996-01-01

    This is the final report on Project #727625 between The Ohio State University and NASA, Lewis Research Center, Cleveland, Ohio. Under this project, a data compression technique for scattered field data of electrically large targets is developed. The technique was applied to the scattered fields of two targets of interest. The backscattered fields of the scale models of these targets were measured in a ra compact range. For one of the targets, the backscattered fields were also calculated using XPATCH computer code. Using the technique all scattered field data sets were compressed successfully. A compression ratio of the order 40 was achieved. In this report, the technique is described briefly and some sample results are included.

  19. Field Assessment Techniques for Bank Erosion Modeling

    Science.gov (United States)

    1990-11-22

    Field Assessment Techniques for Bank Erosion Modeling First Interim Report Prepared for US Army European Research Office US AR DS G-. EDISON HOUSE...SEDIMENTATION ANALYSIS SHEETS and GUIDELINES FOR THE USE OF SEDIMENTATION ANALYSIS SHEETS IN THE FIELD Prepared for US Army Engineer Waterways Experiment...Material Type 3 Material Type 4 Cobbles Toe[’ Toe Toefl Toefl Protection Status Cobbles/boulders Mid-Bnak .. Mid-na.k Mid-Bnask[ Mid-Boak

  20. Progress in automation, robotics and measuring techniques

    CERN Document Server

    Zieliński, Cezary; Kaliczyńska, Małgorzata

    2015-01-01

    This book presents recent progresses in control, automation, robotics, and measuring techniques. It includes contributions of top experts in the fields, focused on both theory and industrial practice. The particular chapters present a deep analysis of a specific technical problem which is in general followed by a numerical analysis and simulation, and results of an implementation for the solution of a real world problem. The presented theoretical results, practical solutions and guidelines will be useful for both researchers working in the area of engineering sciences and for practitioners solving industrial problems.    .

  1. Measurement of Full Field Strains in Filament Wound Composite Tubes Under Axial Compressive Loading by the Digital Image Correlation (DIC) Technique

    Science.gov (United States)

    2013-05-01

    McNeill , S. R. Determination of Displacements Using an Improved Digital Image Correlation Method. Computer Vision August 1983. 13 12. Bruck, H. A... McNeill , S. R.; Russell, S. S.; Sutton, M. A. Use of Digital Image Correlation for Determination of Displacements and Strains. Non-Destructive...Evaluation for Aerospace Requirements, 1989. 13. Sutton, M. A.; McNeill , S. R.; Helm, J. D.; Schreier, H. Full-field Non-Contacting Measurement of

  2. Seminar on Detectors and measurements techniques

    Energy Technology Data Exchange (ETDEWEB)

    Holm, E. (ed.) [Risoe National Lab., Roskilde (Denmark)

    2002-07-01

    A Nordic Seminar on detectors and radionuclide measurement techniques was held in Lund, Sweden, May 3-4, 2001. The objective was to highlight recent progress and problems for techniques to study environmental radioactivity. It covered the aspect of detector sample geometry's and methods for evaluation of gamma gamma pulse height distributions. Within the field of alpha-spectrometric techniques gridded ionisation chambers, semiconductor detectors and a general description for analysis of alpha-particle-spectra were presented. Recent development in mass spectrometric techniques, AMS (Accelerator Mass Spectrometry) and ICPMS (Inductively Coupled Plasma mass Spectrometry) for long-lived radionuclides was described. Principles for analysis of beta particle emitters, especially by liquid scintillation were presented. The seminar also covered radiochemistry such advantages and disadvantages between ion exchange, solvent extraction and extraction chromatography. The use of controlled laboratory conditions for discerning the dynamics of accumulation in organisms was demonstrated. Other techniques such as neutron activation were also shown to be useful analytical tool for certain long-lived radionuclides. The results of the intercalibration exercises within the Nordic countries showed the importance of such analytical quality control. (au)

  3. On cylindrical near-field scanning techniques

    DEFF Research Database (Denmark)

    Appel-Hansen, Jørgen

    1980-01-01

    The agreement between the coupling equations obtained in the literature by using the reciprocity theorem and the scattering matrix formulation is demonstrated. The field is expanded in cylindrical vector wave functions and the addition theorem for these functions is used. The communication may se...... serve as a tutorial introduction to the cylindrical scanning techniques....

  4. Determination of ground water flow using dilution technique. Modification of equipment and supplementary field measurements; Bestaemning av grundvattenfloedet med utspaedningsteknik. Modifiering av utrustning och kompletterande faeltmaetningar

    Energy Technology Data Exchange (ETDEWEB)

    Gustafsson, Erik [Geosigma AB, Uppsala (Sweden)

    2002-12-01

    Equipment for in-situ measurements of ground water flow was modified and improved. Performance data on the dilution sond are discussed in the report, as well as possibilities for further improvements of the equipment. The most important results and conclusions from the tests are: If an accuracy of 10% is acceptable, the lowest measurable flow rate is of the order of 10{sup -11} m/s in fractured granite. Low flows take long time to measure. Measuring the flow through a section with hydraulic conductivity 10{sup -8} at the gradient 0.01 will take 30-50 days in a 110 mm borehole. A 56 mm borehole will need half that time. The optical in-situ measurement of trace element concentration is disturbed, in particular at the beginning of the measurement, by sedimenting particles that have loosened when the sond was lowered into the borehole. The background transmission T{sub b} is a measure of the amount of disturbing particles in the measurement section and is present, as a constant, in the calibration equation. By delaying the trace element injection until the variation of T{sub b} is less than 7.5x10{sup -3} /h the disturbance from sedimenting particles is negligible. The field measurements were performed without problems in 2 m long sections with hydraulic conductivity around 10{sup -7} - 10{sup -8} m/s. The measured flow rates were in the interval 10{sup -8} - 10{sup -9} m/s. Good correlations were established between changes in ground water flow and measured changes in the hydraulic gradient in the test area. Indirect comparisons with hydraulic tests also show small differences, inside the margin of error for the methods.

  5. Metrology of vibration measurements by laser techniques

    Science.gov (United States)

    von Martens, Hans-Jürgen

    2008-06-01

    Metrology as the art of careful measurement has been understood as uniform methodology for measurements in natural sciences, covering methods for the consistent assessment of experimental data and a corpus of rules regulating application in technology and in trade and industry. The knowledge, methods and tools available for precision measurements can be exploited for measurements at any level of uncertainty in any field of science and technology. A metrological approach to the preparation, execution and evaluation (including expression of uncertainty) of measurements of translational and rotational motion quantities using laser interferometer methods and techniques will be presented. The realization and dissemination of the SI units of motion quantities (vibration and shock) have been based on laser interferometer methods specified in international documentary standards. New and upgraded ISO standards are reviewed with respect to their suitability for ensuring traceable vibration measurements and calibrations in an extended frequency range of 0.4 Hz to higher than 100 kHz. Using adequate vibration exciters to generate sufficient displacement or velocity amplitudes, the upper frequency limits of the laser interferometer methods specified in ISO 16063-11 for frequencies procedures (i.e. measurement uncertainty 0.05 % at frequencies <= 10 kHz, <= 1 % up to 100 kHz).

  6. Measuring Earth's Magnetic Field Simply.

    Science.gov (United States)

    Stewart, Gay B.

    2000-01-01

    Describes a method for measuring the earth's magnetic field using an empty toilet paper tube, copper wire, clear tape, a battery, a linear variable resistor, a small compass, cardboard, a protractor, and an ammeter. (WRM)

  7. Field fluctuations measured by interferometry

    Energy Technology Data Exchange (ETDEWEB)

    Glauber, R J [Lyman Laboratory, Harvard University, Cambridge, MA 02138 (United States); Orozco, L A [Joint Quantum Institute, Department of Physics, University of Maryland and National Institute of Standards and Technology, College Park, MD 20742-4111 (United States); Vogel, K; Schleich, W P [Institut fuer Quantenphysik, Universitaet Ulm, D-89069 Ulm (Germany); Walther, H, E-mail: glauber@physics.harvard.ed, E-mail: karl.vogel@uni-ulm.d [Max-Planck-Institut fuer Quantenoptik, Hans-Kopfermann-Strasse 1, D-85748 Garching (Germany)

    2010-09-01

    We derive the complete photon count statistics of an interferometer based on two beam splitters. As a special case we consider a joint intensity-electric field measurement. Our approach is based on the transformation properties of state vectors as well as field operators at a beam splitter.

  8. Soil Sampling Techniques For Alabama Grain Fields

    Science.gov (United States)

    Thompson, A. N.; Shaw, J. N.; Mask, P. L.; Touchton, J. T.; Rickman, D.

    2003-01-01

    Characterizing the spatial variability of nutrients facilitates precision soil sampling. Questions exist regarding the best technique for directed soil sampling based on a priori knowledge of soil and crop patterns. The objective of this study was to evaluate zone delineation techniques for Alabama grain fields to determine which method best minimized the soil test variability. Site one (25.8 ha) and site three (20.0 ha) were located in the Tennessee Valley region, and site two (24.2 ha) was located in the Coastal Plain region of Alabama. Tennessee Valley soils ranged from well drained Rhodic and Typic Paleudults to somewhat poorly drained Aquic Paleudults and Fluventic Dystrudepts. Coastal Plain s o i l s ranged from coarse-loamy Rhodic Kandiudults to loamy Arenic Kandiudults. Soils were sampled by grid soil sampling methods (grid sizes of 0.40 ha and 1 ha) consisting of: 1) twenty composited cores collected randomly throughout each grid (grid-cell sampling) and, 2) six composited cores collected randomly from a -3x3 m area at the center of each grid (grid-point sampling). Zones were established from 1) an Order 1 Soil Survey, 2) corn (Zea mays L.) yield maps, and 3) airborne remote sensing images. All soil properties were moderately to strongly spatially dependent as per semivariogram analyses. Differences in grid-point and grid-cell soil test values suggested grid-point sampling does not accurately represent grid values. Zones created by soil survey, yield data, and remote sensing images displayed lower coefficient of variations (8CV) for soil test values than overall field values, suggesting these techniques group soil test variability. However, few differences were observed between the three zone delineation techniques. Results suggest directed sampling using zone delineation techniques outlined in this paper would result in more efficient soil sampling for these Alabama grain fields.

  9. Improved modeling techniques for turbomachinery flow fields

    Energy Technology Data Exchange (ETDEWEB)

    Lakshminarayana, B.; Fagan, J.R. Jr.

    1995-12-31

    This program has the objective of developing an improved methodology for modeling turbomachinery flow fields, including the prediction of losses and efficiency. Specifically, the program addresses the treatment of the mixing stress tensor terms attributed to deterministic flow field mechanisms required in steady-state Computational Fluid Dynamic (CFD) models for turbomachinery flow fields. These mixing stress tensors arise due to spatial and temporal fluctuations (in an absolute frame of reference) caused by rotor-stator interaction due to various blade rows and by blade-to-blade variation of flow properties. This will be accomplished in a cooperative program by Penn State University and the Allison Engine Company. These tasks include the acquisition of previously unavailable experimental data in a high-speed turbomachinery environment, the use of advanced techniques to analyze the data, and the development of a methodology to treat the deterministic component of the mixing stress tenor.

  10. Surveying techniques in vibration measurement

    Directory of Open Access Journals (Sweden)

    Kuras Przemyslaw

    2015-01-01

    Full Text Available In order to determine the actual dynamic characteristics of engineering structures, it is necessary to perform direct measurements. The paper focuses on the problem of using various devices to measure vibration, with particular emphasis on surveying instruments. The main tool used in this study is the radar interferometer, which has been compared to: robotic total station, GNSS receivers and sensors (accelerometer and encoder. The results of four dynamic experiments are presented. They were performed on: industrial chimney, drilling tower, railway bridge and pedestrian footbridge. The obtained results have been discussed in terms of the requirements imposed by the standard ISO 4866:2010.

  11. Remote field Eddy Current Technique Development for Gap Measurement of Neighboring Tubes of Nuclear Fuel Channel in Pressurized Heavy Water Reactor

    Energy Technology Data Exchange (ETDEWEB)

    Jung, H. K.; Lee, D. H.; Lee, Y. S.; Huh, H.; Cheong, Y. M. [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

    2004-04-15

    Liquid Injection Nozzle(LIN) tube and Calandria tube(CT) in pressurized Heavy Water Reactor (PHWR) are cross-aligned horizontally. These neighboring tubes can contact each other due to the sag of the calandria tube resulting from the irradiation creep and thermal creep, and fuel load, etc. In order to judge the contact which might be the safety concern, the remote field eddy current (RFEC) technology is applied for the gap measurement in this paper. LIN can be detected by inserting the RFEC probe into pressure tube (PT) at the crossing point directly. To obtain the optimal conditions of the RFEC inspection, the sensitivity, penetration and noise signals are considered simultaneously. The optimal frequency and coil spacing are 1kHz and 200mm respectively. Possible noises during LIN signal acquisition are caused by lift-off, PT thickness variation, and gap variation between PT and CT. The simulated noise signals were investigated by the Volume Integral Method(VIM). Signal analysis on the voltage plane describes the amplitude and shape of LIN and possible defects at several frequencies. All the RFEC measurements in the laboratory were done in variance with the CT/LIN gap and showed the relationship between the LIN gap and the signal parameters by analyzing the voltage plane signals

  12. ASD FieldSpec Calibration Setup and Techniques

    Science.gov (United States)

    Olive, Dan

    2001-01-01

    This paper describes the Analytical Spectral Devices (ASD) Fieldspec Calibration Setup and Techniques. The topics include: 1) ASD Fieldspec FR Spectroradiometer; 2) Components of Calibration; 3) Equipment list; 4) Spectral Setup; 5) Spectral Calibration; 6) Radiometric and Linearity Setup; 7) Radiometric setup; 8) Datadets Required; 9) Data files; and 10) Field of View Measurement. This paper is in viewgraph form.

  13. Measurement Error with Different Computer Vision Techniques

    Science.gov (United States)

    Icasio-Hernández, O.; Curiel-Razo, Y. I.; Almaraz-Cabral, C. C.; Rojas-Ramirez, S. R.; González-Barbosa, J. J.

    2017-09-01

    The goal of this work is to offer a comparative of measurement error for different computer vision techniques for 3D reconstruction and allow a metrological discrimination based on our evaluation results. The present work implements four 3D reconstruction techniques: passive stereoscopy, active stereoscopy, shape from contour and fringe profilometry to find the measurement error and its uncertainty using different gauges. We measured several dimensional and geometric known standards. We compared the results for the techniques, average errors, standard deviations, and uncertainties obtaining a guide to identify the tolerances that each technique can achieve and choose the best.

  14. MEASUREMENT ERROR WITH DIFFERENT COMPUTER VISION TECHNIQUES

    Directory of Open Access Journals (Sweden)

    O. Icasio-Hernández

    2017-09-01

    Full Text Available The goal of this work is to offer a comparative of measurement error for different computer vision techniques for 3D reconstruction and allow a metrological discrimination based on our evaluation results. The present work implements four 3D reconstruction techniques: passive stereoscopy, active stereoscopy, shape from contour and fringe profilometry to find the measurement error and its uncertainty using different gauges. We measured several dimensional and geometric known standards. We compared the results for the techniques, average errors, standard deviations, and uncertainties obtaining a guide to identify the tolerances that each technique can achieve and choose the best.

  15. Studies of GRACE Gravity Field Inversion Techniques

    Science.gov (United States)

    Wang, L.; Shum, C.; Duan, J.; Schmidt, M.; Yuan, D.; Watkins, M. M.

    2008-12-01

    The geophysical inverse problem using satellite observations, such as GRACE, to estimate gravity change and mass variations at the Earth's surface is a well-known ill-posed problem. Different methods using different basis function (representing the gravity field) for different purposes (global or regional inversion) have been employed to obtain a stable solution, such as Bayesian estimation with prior information, the repro-BIQUUE of variance components and iterative least-squares estimation with simultaneous updating of a prior covariance, and to achieve enhanced spatial resolutions. The gravity field representation methods include spherical harmonics, regional gridded data (including mascons), and various wavelet representations (Poisson wavelets, Blackman band-limited regional wavelets with global representation). Finally, the use of data types (KBR range, range-rate, range-rate-rate) and data-generation methods (e.g., nonlinear orbit determination and geophysical inverse approach, energy conservation principle, etc) could also reflect relative inversion accuracy and the content of signal spectra in the resulting solution. In this contribution, we present results of a simulation experiment, which used various solution techniques and data types to attempt to quantify the relative advantage and disadvantage of each of the techniques.

  16. Ground-based intercomparison of two isoprene measurement techniques

    Directory of Open Access Journals (Sweden)

    E. Leibrock

    2003-01-01

    Full Text Available An informal intercomparison of two isoprene (C5H8 measurement techniques was carried out during Fall of 1998 at a field site located approximately 3 km west of Boulder, Colorado, USA. A new chemical ionization mass spectrometric technique (CIMS was compared to a well-established gas chromatographic technique (GC. The CIMS technique utilized benzene cation chemistry to ionize isoprene. The isoprene levels measured by the CIMS were often larger than those obtained with the GC. The results indicate that the CIMS technique suffered from an anthropogenic interference associated with air masses from the Denver, CO metropolitan area as well as an additional interference occurring in clean conditions. However, the CIMS technique is also demonstrated to be sensitive and fast. Especially after introduction of a tandem mass spectrometric technique, it is therefore a candidate for isoprene measurements in remote environments near isoprene sources.

  17. Unified Application of Vapor Screen Flow Visualization and Pressure Sensitive Paint Measurement Techniques to Vortex- and Shock Wave-Dominated Flow Fields

    Science.gov (United States)

    Erickson, Gary E.

    2010-01-01

    Laser vapor screen (LVS) flow visualization and pressure sensitive paint (PSP) techniques were applied in a unified approach to wind tunnel testing of slender wing and missile configurations dominated by vortex flows and shock waves at subsonic, transonic, and supersonic speeds. The off-surface cross-flow patterns using the LVS technique were combined with global PSP surface static pressure mappings to characterize the leading-edge vortices and shock waves that coexist and interact at high angles of attack. The synthesis of LVS and PSP techniques was also effective in identifying the significant effects of passive surface porosity and the presence of vertical tail surfaces on the flow topologies. An overview is given of LVS and PSP applications in selected experiments on small-scale models of generic slender wing and missile configurations in the NASA Langley Research Center (NASA LaRC) Unitary Plan Wind Tunnel (UPWT) and 8-Foot Transonic Pressure Tunnel (8-Foot TPT).

  18. Unified Application Vapor Screen Flow Visualization and Pressure Sensitive Paint Measurement Techniques to Vortex- and Shock Wave-Dominated Flow Fields

    Science.gov (United States)

    Erickson, Gary E.

    2008-01-01

    Laser vapor screen (LVS) flow visualization and pressure sensitive paint (PSP) techniques were applied in a unified approach to wind tunnel testing of slender wing and missile configurations dominated by vortex flows and shock waves at subsonic, transonic, and supersonic speeds. The off-surface cross-flow patterns using the LVS technique were combined with global PSP surface static pressure mappings to characterize the leading-edge vortices and shock waves that coexist and interact at high angles of attack (alpha). The synthesis of LVS and PSP techniques was also effective in identifying the significant effects of passive surface porosity and the presence of vertical tail surfaces on the flow topologies. An overview is given of LVS and PSP applications in selected experiments on small-scale models of generic slender wing and missile configurations in the NASA Langley Research Center (NASA LaRC) Unitary Plan Wind Tunnel (UPWT) and 8-Foot Transonic Pressure Tunnel (8-Foot TPT).

  19. Local electric field measurements by optical tweezers

    Directory of Open Access Journals (Sweden)

    G. Pesce

    2011-09-01

    Full Text Available We report a new technique to measure direction and amplitude of electric fields generated by microelectrodes embedded in polar liquid environment, as often used in microfluidic devices. The method is based on optical tweezers which act as sensitive force transducer while a trapped charged microsphere behaves as a probe. When an electric field is applied the particles moves from its equilibrium position and finishes in a new equilibrium position where electric and optical forces are balanced. A trapped bead is moved to explore the electric field in a wide region around the microelectrodes. In such way maps of electric fields with high spatial resolution can be reconstructed even for complex electrode geometries where numerical simulation approaches can fail. Experimental results are compared with calculations based on finite element analysis simulation.

  20. Experimental Techniques for Thermodynamic Measurements of Ceramics

    Science.gov (United States)

    Jacobson, Nathan S.; Putnam, Robert L.; Navrotsky, Alexandra

    1999-01-01

    Experimental techniques for thermodynamic measurements on ceramic materials are reviewed. For total molar quantities, calorimetry is used. Total enthalpies are determined with combustion calorimetry or solution calorimetry. Heat capacities and entropies are determined with drop calorimetry, differential thermal methods, and adiabatic calorimetry . Three major techniques for determining partial molar quantities are discussed. These are gas equilibration techniques, Knudsen cell methods, and electrochemical techniques. Throughout this report, issues unique to ceramics are emphasized. Ceramic materials encompass a wide range of stabilities and this must be considered. In general data at high temperatures is required and the need for inert container materials presents a particular challenge.

  1. Measurement of solid concentration using Terahertz technique

    Institute of Scientific and Technical Information of China (English)

    Liu Yi'an; Huang Zhiyao; Ji Haifeng; Wang Baoliang; Li Haiqing

    2007-01-01

    Terahertz(THz)technique is a new measurement technique that has emerged in recent years. For the measurement of solid concentration, a radiation attenuation method and a phase delay method were developed, which are based on the Beer-Lambert law. Experimental work was carried out on a terahertz time-domain spectroscopy system (THz-TDS). Results obtained verify that the terahertz technique may provide a possible new solution to the problem of solid concentration measurement and the two proposed measurement methods are effective. Experiment results also indicate that the phase delay method is more accurate than the radiation attenuation method and the size of the particles affects the measurement results of both methods.

  2. Multidirectional mobilities: Advanced measurement techniques and applications

    Science.gov (United States)

    Ivarsson, Lars Holger

    Today high noise-and-vibration comfort has become a quality sign of products in sectors such as the automotive industry, aircraft, components, households and manufacturing. Consequently, already in the design phase of products, tools are required to predict the final vibration and noise levels. These tools have to be applicable over a wide frequency range with sufficient accuracy. During recent decades a variety of tools have been developed such as transfer path analysis (TPA), input force estimation, substructuring, coupling by frequency response functions (FRF) and hybrid modelling. While these methods have a well-developed theoretical basis, their application combined with experimental data often suffers from a lack of information concerning rotational DOFs. In order to measure response in all 6 DOFs (including rotation), a sensor has been developed, whose special features are discussed in the thesis. This transducer simplifies the response measurements, although in practice the excitation of moments appears to be more difficult. Several excitation techniques have been developed to enable measurement of multidirectional mobilities. For rapid and simple measurement of the loaded mobility matrix, a MIMO (Multiple Input Multiple Output) technique is used. The technique has been tested and validated on several structures of different complexity. A second technique for measuring the loaded 6-by-6 mobility matrix has been developed. This technique employs a model of the excitation set-up, and with this model the mobility matrix is determined from sequential measurements. Measurements on ``real'' structures show that both techniques give results of similar quality, and both are recommended for practical use. As a further step, a technique for measuring the unloaded mobilities is presented. It employs the measured loaded mobility matrix in order to calculate compensation forces and moments, which are later applied in order to compensate for the loading of the

  3. High-voltage test and measuring techniques

    Energy Technology Data Exchange (ETDEWEB)

    Hauschild, Wolfgang; Lemke, Eberhard

    2014-04-01

    Reflects the unit of both HV testing and measuring technique. Intended as an ''application guide'' for the relevant IEC standards. Refers also to future trends in HV testing and measuring technique. With numerous illustrations. It is the intent of this book to combine high-voltage (HV) engineering with HV testing technique and HV measuring technique. Based on long-term experience gained by the authors as lecturer and researcher as well as member in international organizations, such as IEC and CIGRE, the book will reflect the state of the art as well as the future trends in testing and diagnostics of HV equipment to ensure a reliable generation, transmission and distribution of electrical energy. The book is intended not only for experts but also for students in electrical engineering and high-voltage engineering.

  4. Microwave field measurement via Rabi resonances in Cs atoms

    CERN Document Server

    Sun, Fuyu; Bai, Qingsong; Huang, Xianhe; Ma, Jie; Li, Xiaofeng

    2016-01-01

    We present a technique for measuring microwave (MW) field based on Rabi resonances induced by the interaction of atoms with a phase-modulated MW field. A theoretical model of field measurement is used to calculate Rabi frequency. Single-peak feature of the measurement model makes the technique a valuable tool for simple and fast field measurement. As an example, we use the technique to determine the MW field strength inside a Cs vapor cell in the X-band rectangular cavity for applied power in the range of -21 dBm to 20 dBm. The results show that this proposed technique is capable for detecting the field over a broad dynamical range.

  5. Blood Glucose Measurement Using Bioimpedance Technique

    OpenAIRE

    2014-01-01

    Bioimpedance measurement is gaining importance in wide field of bioresearch and biomedical systems due to its noninvasive nature. Noninvasive measurement method is very important to decrease infection and physical injuries which result due to invasive measurement. This paper presents basic principle of bioimpedance along with its application for blood glucose analysis and effect of frequency on impedance measurement. Input from bioimpedance sensor is given to amplifier and signal conditioner ...

  6. Review of air flow measurement techniques

    Energy Technology Data Exchange (ETDEWEB)

    McWilliams, Jennifer

    2002-12-01

    Airflow measurement techniques are necessary to determine the most basic of indoor air quality questions: ''Is there enough fresh air to provide a healthy environment for the occupants of the building?'' This paper outlines airflow measurement techniques, but it does not make recommendations for techniques that should be used. The airflows that will be discussed are those within a room or zone, those between rooms or zones, such as through doorways (open or closed) or passive vents, those between the building and outdoors, and those through mechanical air distribution systems. Techniques that are highlighted include particle streak velocimetry, hot wire anemometry, fan pressurization (measuring flow at a given pressure), tracer gas, acoustic methods for leak size determination, the Delta Q test to determine duct leakage flows, and flow hood measurements. Because tracer gas techniques are widely used to measure airflow, this topic is broken down into sections as follows: decay, pulse injection, constant injection, constant concentration, passive sampling, and single and multiple gas measurements for multiple zones.

  7. Companding technique for high dynamic range measurements using Gafchromic films

    Energy Technology Data Exchange (ETDEWEB)

    Van den Heuvel, Frank; Crijns, Wouter; Defraene, Gilles [Department of Experimental Radiotherapy, Catholic University of Leuven, Leuven, Belgium B-3000 (Belgium)

    2011-12-15

    Purpose: To introduce a methodology to perform dose measurements using Gafchromic films which can span several decades of dose levels. Methods: The technique is based on a rescaling approach using different films irradiated at different dose levels. This is combined with a registration protocol correcting positioning and scaling factors for each film. The methodology is validated using TLD's for out-of-field doses. Furthermore, two examples are provided using the technique to characterize small sized radiosurgery cones and compared with measurements made with a pinpoint chamber. Results: Excellent agreement with TLD, planning systems and measurement was found. The superior resolution of the film technique was apparent. Conclusions: The authors have introduced a new technique allowing users to quantify very low doses in conjunction with commissioning measurements. The use of film also provides 2D information on beam characteristics in high resolution measurements.

  8. VALUATION TECHNIQUES USED IN FAIR VALUE MEASUREMENT

    OpenAIRE

    Cristina-Aurora, BUNEA-BONTAS

    2013-01-01

    Valuation of assets and liabilities involves significant judgements and estimates, especially when fair value measurement is required. Currently, IFRS 13 Fair Value Measurement offers a single and more comprehensive source of guidance that is applied to almost all fair value estimates. When measuring fair value of fixed assets, intangible assets, specified financial assets or liabilities, different valuation techniques may be used: the market approach, the cost approach and the income appr...

  9. New optical technique for bulk magnetostriction measurement

    CERN Document Server

    Samata, H; Uchida, T; Abe, S

    2000-01-01

    A new optical technique was applied to the measurement of magnetostriction in bulk samples. This technique utilizes an optical fiber bundle, AC-modulated light and lock-in detection. Deformation of the sample is determined from the ratio of the incident and reflected light intensities. Noise due to the instability of the light source is eliminated by obtaining the ratio of the incident and reflected light intensities, and the noise caused in the detector circuit can be reduced by lock-in detection. The performance of this method was characterized with a series of measurements using a gold film and crystal disks of pure iron and nickel. This technique offers a resolution of 0.5 nm and is sensitive enough to measure magnetostriction as small as 5x10 sup - sup 7 in 1 mm thick samples.

  10. VALUATION TECHNIQUES USED IN FAIR VALUE MEASUREMENT

    Directory of Open Access Journals (Sweden)

    Cristina-Aurora, BUNEA-BONTAS

    2013-12-01

    Full Text Available Valuation of assets and liabilities involves significant judgements and estimates, especially when fair value measurement is required. Currently, IFRS 13 Fair Value Measurement offers a single and more comprehensive source of guidance that is applied to almost all fair value estimates. When measuring fair value of fixed assets, intangible assets, specified financial assets or liabilities, different valuation techniques may be used: the market approach, the cost approach and the income approach. This article reviews these techniques and points out that different valuation practices may provide different results depending on the item being fair valued and on the inputs used. Also it emphasizes that, in particular circumstances, there is the possibility that a certain technique may be more appropriate than other.

  11. Solar Cell Calibration and Measurement Techniques

    Science.gov (United States)

    Bailey, Sheila; Brinker, Dave; Curtis, Henry; Jenkins, Phillip; Scheiman, Dave

    2004-01-01

    The increasing complexity of space solar cells and the increasing international markets for both cells and arrays has resulted in workshops jointly sponsored by NASDA, ESA and NASA. These workshops are designed to obtain international agreement on standardized values for the AMO spectrum and constant, recommend laboratory measurement practices and establish a set of protocols for international comparison of laboratory measurements. A working draft of an ISO standard, WD15387, "Requirements for Measurement and Calibration Procedures for Space Solar Cells" was discussed with a focus on the scope of the document, a definition of primary standard cell, and required error analysis for all measurement techniques. Working groups addressed the issues of Air Mass Zero (AMO) solar constant and spectrum, laboratory measurement techniques, and te international round robin methodology. A summary is presented of the current state of each area and the formulation of the ISO document.

  12. Data acquisition and preprocessing techniques for remote sensing field research

    Science.gov (United States)

    Biehl, L. L.; Robinson, B. F.

    1983-01-01

    A crops and soils data base has been developed at Purdue University's Laboratory for Applications of Remote Sensing using spectral and agronomic measurements made by several government and university researchers. The data are being used to (1) quantitatively determine the relationships of spectral and agronomic characteristics of crops and soils, (2) define future sensor systems, and (3) develop advanced data analysis techniques. Researchers follow defined data acquisition and preprocessing techniques to provide fully annotated and calibrated sets of spectral, agronomic, and meteorological data. These procedures enable the researcher to combine his data with that acquired by other researchers for remote sensing research. The key elements or requirements for developing a field research data base of spectral data that can be transported across sites and years are appropriate experiment design, accurate spectral data calibration, defined field procedures, and through experiment documentation.

  13. A Wireless Fluid-Level Measurement Technique

    Science.gov (United States)

    Woodard, Stanley E.; Taylor, Bryant D.

    2006-01-01

    This paper presents the application of a recently developed wireless measurement acquisition system to fluid-level measurement. This type of fluid-level measurement system alleviates many shortcomings of fluid-level measurement methods currently being used, including limited applicability of any one fluid-level sensor design. Measurement acquisition shortcomings include the necessity for power to be supplied to each sensor and for the measurement to be extracted from each sensor via a physical connection to the sensor. Another shortcoming is existing measurement systems require that a data channel and signal conditioning electronics be dedicated to each sensor. Use of wires results in other shortcomings such as logistics needed to add or replace sensors, weight, potential for electrical arcing and wire degradations. The fluid level sensor design is a simple passive inductor-capacitor circuit that is not subject to mechanical failure that is possible when float and lever-arm systems are used. Methods are presented for using the sensor in caustic, acidic or cryogenic fluids. Oscillating magnetic fields are used to power the sensor. Once electrically excited, the sensor produces a magnetic field response. The response frequency corresponds to the amount to fluid within the capacitor s electric field. The sensor design can be modified for measuring the level of any fluid or fluent substance that can be stored in a non-conductive reservoir. The interrogation method for discerning changes in the sensor response frequency is also presented.

  14. Measurements of diversity gain and radiation efficiency of the eleven antenna by using different measurement techniques

    DEFF Research Database (Denmark)

    Yang, Jian; Pivnenko, Sergey; Laitinen, Tommi

    2010-01-01

    This paper presents measurement results of diversity gain and radiation efficiency by using three different measurement techniques: reverberation chamber, spherical near-field anechoic chamber, and multi-probe anechoic chamber. The results are measured over a large 2–8 GHz bandwidth which...

  15. 脉冲交变磁场测量技术缺陷识别与定量评估%Pulsed Alternating Current Field Measurement Technique for Defect Identification and Quantification

    Institute of Scientific and Technical Information of China (English)

    胡祥超; 罗飞路; 何赟泽; 唐莺

    2011-01-01

    传统的交变磁场测量(Alternating current field measurement,ACFM)技术具有缺陷定量准确、无需接触等优点,但是不能检测深层缺陷;脉冲涡流检测技术(Pulsed eddy current testing,PECT)具有较好的深层缺陷检测能力,但由于采用瞬态响应信号分析方法,容易受到提离效应干扰,工程实际应用较为困难,并且定量能力弱于ACFM技术.结合ACFM和PECT的优势,提出了脉冲交变磁场测量技术(Pulsed alternating current field measurement,PACFM).该技术采用脉冲周期信号作为激励信号源,基于瞬态脉冲响应信号,采用三维场量测量和瞬态信号分析相结合的方法实现缺陷识别与定量评估.对瞬态响应信号中能够表征磁场变化规律的特征量进行提取,通过研究发现PACFM不仅具有与ACFM等同的表面缺陷检测能力,而且具有优异的深层缺陷识别与定最评估能力,抗干扰能力强,具有较高的应用价值和前景.%Traditional alternating current field measurement (ACFM) technique has advantages of quantitative defect detection and noncontact, but poor detective performances on deep-layer defects. Pulsed eddy current testing (PECT) has a better detectability in deep-layer defect, but poorer quantitative performances than ACFM, and moreover, it is easily interfered by lift-off due to using transient response signal analysis method so it is difficult to be applied practically. A method of alternating current filed measurement with pulsed signal excitation is proposed, which implements defect detection and quantitative evaluation by approach of transient signal analysis combined with 3D magnetic filed measurement based on pulsed response signal. Characteristics in the transient response signal which can reflect the variation law of magnetic field are extracted. Through the study it is found that the pulsed alternating current field measurement has not only the same detectability of surface defects as ACFM, but also an

  16. Comparison of cardiac output measurement techniques

    DEFF Research Database (Denmark)

    Espersen, K; Jensen, E W; Rosenborg, D;

    1995-01-01

    Simultaneously measured cardiac output obtained by thermodilution (TD), transcutaneous suprasternal ultrasonic Doppler (DOP), CO2-rebreathing (CR) and the direct Fick method (FI) were compared in eleven healthy subjects in a supine position (SU), a sitting position (SI), and during sitting exercise...... at a workload of 50 W (EX). The agreements between the techniques, two by two, were expressed as the bias calculated as the averaged differences between the techniques. Precision was expressed as the standard deviation of the bias. The overall agreement (bias +/- precision) between TD, DOP and CR respectively...... and CR, respectively, and TD were 2.5 +/- 2.2 and 2.6 +/- 1.6 l/min. The overall agreement between DOP and CR was 0.1 +/- 1.6 l/min. In conclusion, TD overestimated cardiac output compared to the other techniques and the poor agreement has to be taken into consideration especially in measures of low...

  17. Blood Glucose Measurement Using Bioimpedance Technique

    Directory of Open Access Journals (Sweden)

    D. K. Kamat

    2014-01-01

    Full Text Available Bioimpedance measurement is gaining importance in wide field of bioresearch and biomedical systems due to its noninvasive nature. Noninvasive measurement method is very important to decrease infection and physical injuries which result due to invasive measurement. This paper presents basic principle of bioimpedance along with its application for blood glucose analysis and effect of frequency on impedance measurement. Input from bioimpedance sensor is given to amplifier and signal conditioner AD5933. AD5933 is then interfaced with microcontroller LPC1768 using I2C bus for displaying reading on LCD. Results can also be stored in database using UART interface of LPC1768.

  18. Electric Field Effects in RUS Measurements

    Energy Technology Data Exchange (ETDEWEB)

    Darling, Timothy W [Los Alamos National Laboratory; Ten Cate, James A [Los Alamos National Laboratory; Allured, Bradley [UNIV NEVADA, RENO; Carpenter, Michael A [CAMBRIDGE UNIV. UK

    2009-09-21

    Much of the power of the Resonant Ultrasound Spectroscopy (RUS) technique is the ability to make mechanical resonance measurements while the environment of the sample is changed. Temperature and magnetic field are important examples. Due to the common use of piezoelectric transducers near the sample, applied electric fields introduce complications, but many materials have technologically interesting responses to applied static and RF electric fields. Non-contact optical, buffered, or shielded transducers permit the application of charge and externally applied electric fields while making RUS measurements. For conducting samples, in vacuum, charging produces a small negative pressure in the volume of the material - a state rarely explored. At very high charges we influence the electron density near the surface so the propagation of surface waves and their resonances may give us a handle on the relationship of electron density to bond strength and elasticity. Our preliminary results indicate a charge sign dependent effect, but we are studying a number of possible other effects induced by charging. In dielectric materials, external electric fields influence the strain response, particularly in ferroelectrics. Experiments to study this connection at phase transformations are planned. The fact that many geological samples contain single crystal quartz suggests a possible use of the piezoelectric response to drive vibrations using applied RF fields. In polycrystals, averaging of strains in randomly oriented crystals implies using the 'statistical residual' strain as the drive. The ability to excite vibrations in quartzite polycrystals and arenites is explored. We present results of experimental and theoretical approaches to electric field effects using RUS methods.

  19. High-voltage test and measuring techniques

    CERN Document Server

    Hauschild, Wolfgang

    2014-01-01

    It is the intent of this book to combine high-voltage (HV) engineering with HV testing technique and HV measuring technique. Based on long-term experience gained by the authors as lecturer and researcher as well as member in international organizations, such as IEC and CIGRE, the book will reflect the state of the art as well as the future trends in testing and diagnostics of HV equipment to ensure a reliable generation, transmission and distribution of electrical energy. The book is intended not only for experts but also for students in electrical engineering and high-voltage engineering.

  20. Characterization of small antennas for hearing aids by several measurement techniques

    DEFF Research Database (Denmark)

    Pivnenko, Sergey; Zhang, Jiaying; Khatun, Afroza;

    2010-01-01

    Characteristics of electrically small loop antennas were measured by different techniques and the results were compared in-between. The techniques employed were: a single-probe spherical near-field technique, a multi-probe spherical near-field technique, a reverberation chamber, and a Wheeler cap...

  1. Integration of Field and Remote Sensing Techniques For Landslides Monitoring

    Science.gov (United States)

    Allievi, J.; Ambrosi, C.; Ceriani, M.; Colesanti, C.; Crosta, G. B.; Ferretti, A.; Fossati, D.; Menegaz, A.

    The definition of the state of activity of slope movements is of major interest both at local and at regional scale. The Geological Survey of the Regione Lombardia has re- cently started a series of projects aimed to the identification of areas subjected to slope instability and to the assessment of their state of activity. Field survey, aerial photo interpretation and advanced remote sensing techniques have been applied. Some ex- amples of large rock slope instabilities have been investigated in the Valtellina area (Lombardia, Northern Italy). In particular, we demonstrate the degree of integration of the adopted techniques for one of the largest rock slope movements actually recog- nised in the area. The remote sensing approach that has been adopted is the Perma- nent Scatterers (PS) Technique. This technique has been recently developed as a new methodology for surface deformation monitoring, using ESA ERS-SAR data. Its ap- plication to large slope movements in alpine and prealpine areas, with a relatively low urban development, has been tried for the first time in order to evaluate its potential in supporting studies for landslide hazard assessment. Previous results show that this ap- proach allows to reach an accuracy very close to the theoretical limit. This study shows the very good agreement reached for displacement velocities between historical trends and recent PS measurements. Scatterers have been identified by field surveying and some of them are located close to historically monitored benchmark for topographic measurements. Furthermore, the integration of these data with field observations al- lowed us to perform a preliminary reconstrucion of the landslide mechanism and to assess the activity of different landslide structures (scarps, etc.).

  2. Laser Feedback Technique for Precise Retardation Measurements

    Institute of Scientific and Technical Information of China (English)

    FEI Li-Gang; ZHANG Shu-Lian

    2006-01-01

    @@ A simple and precise retardation measurement based on laser feedback is demonstrated. The measurement principle is based on polarization flipping induced by optical feedback from an external birefringence cavity.The measured wave plate is located in the external cavity. When the length of the external cavity is tuned,the polarization states of laser will flip between two eigenstates, and the position of polarization flipping in one period of intensity modulation will vary with retardation of the wave plate. The duty ratio of two eigenstates is used to determine the retardation. Main advantages of the technique are that it is compact, low cost, fast and flexible. Especially, it is insensitive to a fluctuation of laser intensity and is suitable for on-line measurement. The experimental results have shown that the measurement uncertainty is better than 0.03° in the range 30°-150°.

  3. Equipment for measuring radiation. Part 3. Technique of measuring radiation

    Energy Technology Data Exchange (ETDEWEB)

    Radwanowski, L.J.

    1979-01-01

    Difficulties are noted in measuring the effects of radiation because of the excessively low energy of the measured fields. In nature there are different magnetic-dynamic and magnetic-hydrodynamic generators which are sources of very low intensity which changes in time. The equipment of measurements is examined in the example of one of the generators, underground water current. The apparatus is described in detail for measuring the intensity of the electromagnetic SHF field. Under the underground water currents a change is observed in the intensity of the electromagnetic field. The possibilities are also examined of direct measurement of ultrasonic elastic fluctuations caused by the underground current, as well as the possibility of recording other physical fields (spontaneous polarization, soil temperature). A study was made of the effect of the underground water current on the occurrence of physical, chemical and biological processes: photochemical reactions, reactions of metal oxidation, Golomb effect (change in the rate of sedimentation of argillaceous particles in water under the influence of a biofield), change in air humidity and soil water content, change in intensity of the magnetic field, Hall effect, change in luminescence of certain organisms or the luminophore released by them. Basic plans are presented of certain measurement and recording devices.

  4. Techniques to measure testosterone in the elderly.

    Science.gov (United States)

    Klee, G G; Heser, D W

    2000-01-01

    In today's clinical and research settings, there is an unfortunate lack of consistency for the term "measuring testosterone status." This term is often used to refer to a measure of biologic androgen activity rather than the specific measurement of the chemical concentration of the testosterone steroid molecule. Even the measurements of chemical concentrations show considerable methodologic differences. This is true for measurements in elderly men, as well as in other populations, including women. All of the current methods for measuring total testosterone have limitations, especially with regard to low concentrations. In addition, unresolved questions concerning the active form of the hormone preclude definitive determination of which form of testosterone and which other androgen hormones are best suited for measuring androgen activity. When measurement techniques are compared, the numbers correlate with each other but certainly do not represent the same value. There is a need for a consensus as to which forms of hormones should be measured to best assess androgen status, and there is a need to standardize the procedures used to measure these hormones.

  5. PM10 source measurement methodology: Field studies

    Energy Technology Data Exchange (ETDEWEB)

    Farthing, W.E.; Martin, R.S.; Dawes, S.S.; Williamson, A.D.

    1989-05-01

    Two candidate measurement methods, Constant Sampling Rate (CSR) and Exhaust Gas Recycle (EGR), have been developed to measure emissions of in-stack PM-10 particulate matter with aerodynamic diameter less than 10 micrometers. Two field tests were performed at the clinker cooler exhaust of a Portland cement plant to quantify precision and comparability of these techniques. In addition, accuracy was determined for total particulate measurement by comparison to Method 17. Collocated sampling trains were operated parallel with two Method 17 trains. In the second test, two CSR and one EGR trains were operated parallel to two Method 17 trains. The operating procedures used for the CSR and EGR trains are described in detail. In measurement of PM-10 and total particulate matter, the precision of both the CSR and EGR techniques was found to be of the same magnitude as Method 17 (approximately 5%). A small bias was found between CSR and EGR PM-10 results (15%) and between EGR and Method 17 total particulate matter (10%). Although small, these observed differences, combined with the results of laboratory studies reported elsewhere, led to a recommendation for an increase in the length of sampling nozzles. This modification improved cyclone performance and is incorporated into the nozzle geometries described in the application guides for CSR and EGR.

  6. Surface Wear Measurement Using Optical Correlation Technique

    Science.gov (United States)

    Acinger, Kresimir

    1983-12-01

    The coherent optical correlation technique was applied for measuring the surface wear of a tappet (part of car engine), worn by friction with the camshaft. It was found that maximum correlation intensity decays exponentially with the number of wear cycles (i.e. camshaft revolutions). Tappets of the same make have an identical rate of correlation decay. Tappets of different makes have different rates of correlation decay which are in agreement with observed long term wear.

  7. Field-in-Field Technique to Improve Dose Distribution in the Junction of the Field with Head and Neck Cancer

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Seon Myeong; Lee, Yeong Cheol; Jeong, Daek Yang; Kim, Young Bum [Dept. of Radiation Oncology, Korea University Guro Hospital, Seoul (Korea, Republic of)

    2009-03-15

    In treating head and neck cancer, it is very important to irradiate uniform dose on the junction of the bilateral irradiation field of the upper head and neck and the anterior irradiation field of the lower neck. In order to improve dose distribution on the junction, this study attempted to correct non uniform dose resulting from under dose and over dose using the field-in-field technique in treating the anterior irradiation field of the lower neck and to apply the technique to the treatment of head and neck cancer through comparison with conventional treatment. In order to examine dose difference between the entry point and the exit point where beam diffusion happens in bilateral irradiation on the upper head and neck, we used an anthropomorphic phantom. Computer Tomography was applied to the anthropomorphic phantom, the dose of interest points was compared in radiation treatment planning, and it was corrected by calculating the dose ratio at the junction of the lower neck. Dose distribution on the junction of the irradiated field was determined by placing low-sensitivity film on the junction of the lower neck and measuring dose distribution on the conventional bilateral irradiation of the upper head and neck and on the anterior irradiation of the lower neck. In addition, using the field-in-field technique, which takes into account beam diffusion resulting from the bilateral irradiation of the upper head and neck, we measured difference in dose distribution on the junction in the anterior irradiation of the lower neck. In order to examine the dose at interest points on the junction, we compared and analyzed the change of dose at the interest points on the anthropomorphic phantom using a thermoluminescence dosimeter. In case of dose sum with the bilateral irradiation of the upper head and neck when the field-in-field technique is applied to the junction of the lower neck in radiation treatment planning, The dose of under dose areas increased by 4.7-8.65%. The dose

  8. Single spin measurement using cellular automata techniques

    CERN Document Server

    Perez-Delgado, C A; Cory, D G; Mosca, M; Cappellaro, Paola; Cory, David G.; Mosca, Michele; Perez-Delgado, Carlos A.

    2006-01-01

    We propose an approach for single spin measurement. Our method uses techniques from the theory of quantum cellular automata to correlate a large amount of ancillary spins to the one to be measured. It has the distinct advantage of being efficient, and to a certain extent fault-tolerant. Under ideal conditions, it requires the application of only order of cube root of N steps (each requiring a constant number of rf pulses) to create a system of N correlated spins. It is also fairly robust against pulse errors, imperfect initial polarization of the ancilla spin system, and does not rely on entanglement. We study the scalability of our scheme through numerical simulation.

  9. High resolution temperature measurement technique for measuring marine heat flow

    Institute of Scientific and Technical Information of China (English)

    QIN; YangYang; YANG; XiaoQiu; WU; BaoZhen; SUN; ZhaoHua; SHI; XiaoBin

    2013-01-01

    High resolution temperature measurement technique is one of the key techniques for measuring marine heat flow. Basing on Pt1000 platinum resistance which has the characteristics of high accuracy and good stability, we designed a bridge reversal excitation circuit for high resolution temperature measurement. And the deep ocean floor in-situ test results show that: (1) temperature deviation and peak-to-peak resolution of the first version circuit board (V1) are 1.960-1.990 mK and 0.980-0.995 m Kat 1.2-2.7°C, respectively; and temperature deviation and peak-to-peak resolution of the second circuit board (V2) are 2.260mK and 1.130 mK at 1.2-1.3°C, respectively; (2) During the 2012NSFC-IndOcean cruise, seafloor geothermal gradient at Ind2012HF03,-07 and-12 stations (water depth ranges from 3841 to 4541 m) were successfully measured, the values are 59.1,75.1 and 71.6°C/km, respectively. And the measurement errors of geothermal gradient at these three stations are less than 3.0% in terms of the peak-to-peak resolution. These indicate that the high resolution temperature measurement technique based on Pt1000 platinum resistance in this paper can be applied to marine heat flow measurement to obtain high precision geothermal parameters.

  10. Strain Measurement on the Toroidal Field (TF) Coil Cases

    Institute of Scientific and Technical Information of China (English)

    Chen Zhuomin; Long Feng; Wu Hao

    2005-01-01

    The stress-strain state of the structure is a matter of interest to designer. The strain measurement of superconducting magnets at cryogenic temperature is a specific technique. Based on strain measurement of TF coil case for EAST, this paper presents a measuring technique at cryogenic temperature and on intense magnetic field. The compensation methods for both temperature and magnetic field effects of the gauges, together with the measured results are involved, and the discussions of the measured results are given in the paper.

  11. Electromagnetic measurements in the near field

    CERN Document Server

    Bienkowski, Pawel

    2012-01-01

    This book is devoted to the specific problems of electromagnetic field (EMF) measurements in the near field and to the analysis of the main factors which impede accuracy in these measurements. It focuses on careful and accurate design of systems to measure in the near field based on a thorough understanding of the fundamental engineering principles and on an analysis of the likely system errors. Beginning with a short introduction to electromagnetic fields with an emphasis on the near field, it them presents methods of EMF measurements in near field conditions. It details the factors limiting

  12. A DGT technique for plutonium bioavailability measurements.

    Science.gov (United States)

    Cusnir, Ruslan; Steinmann, Philipp; Bochud, François; Froidevaux, Pascal

    2014-09-16

    The toxicity of heavy metals in natural waters is strongly dependent on the local chemical environment. Assessing the bioavailability of radionuclides predicts the toxic effects to aquatic biota. The technique of diffusive gradients in thin films (DGT) is largely exploited for bioavailability measurements of trace metals in waters. However, it has not been applied for plutonium speciation measurements yet. This study investigates the use of DGT technique for plutonium bioavailability measurements in chemically different environments. We used a diffusion cell to determine the diffusion coefficients (D) of plutonium in polyacrylamide (PAM) gel and found D in the range of 2.06-2.29 × 10(-6) cm(2) s(-1). It ranged between 1.10 and 2.03 × 10(-6) cm(2) s(-1) in the presence of fulvic acid and in natural waters with low DOM. In the presence of 20 ppm of humic acid of an organic-rich soil, plutonium diffusion was hindered by a factor of 5, with a diffusion coefficient of 0.50 × 10(-6) cm(2) s(-1). We also tested commercially available DGT devices with Chelex resin for plutonium bioavailability measurements in laboratory conditions and the diffusion coefficients agreed with those from the diffusion cell experiments. These findings show that the DGT methodology can be used to investigate the bioaccumulation of the labile plutonium fraction in aquatic biota.

  13. The measurement of the modal strain fields using digital shearography

    Science.gov (United States)

    Lopes, H.; Ribeiro, J. E.; Vaz, M.; Gomes, J. M.

    2010-06-01

    This work presents a Michelson shearography interferometer configuration associated with stroboscopic double illumination technique for the measurement of modal rotation fields and their strain fields on a clamped circular aluminium plate. The speckle pattern is frozen by the synchronization between the LASER illumination and the modal vibration of the object. The quantitative evaluation is performed for each digital shearogram using a time modulation technique. The setup of double illumination LASER with out-of-plane opposite sensitivity allows the two phase maps measurement of the modal spatial gradient. The modal rotation and strain fields are extracted by the combination of this two digital phase maps. Image processing techniques are applied on the phase maps to obtain full-field measurements using a dedicated post-processing algorithm. Finally, is presented a comparison between the experimental measurement and the numerical solution.

  14. The measurement of the modal strain fields using digital shearography

    Directory of Open Access Journals (Sweden)

    Gomes J.M.

    2010-06-01

    Full Text Available This work presents a Michelson shearography interferometer configuration associated with stroboscopic double illumination technique for the measurement of modal rotation fields and their strain fields on a clamped circular aluminium plate. The speckle pattern is frozen by the synchronization between the LASER illumination and the modal vibration of the object. The quantitative evaluation is performed for each digital shearogram using a time modulation technique. The setup of double illumination LASER with out-of-plane opposite sensitivity allows the two phase maps measurement of the modal spatial gradient. The modal rotation and strain fields are extracted by the combination of this two digital phase maps. Image processing techniques are applied on the phase maps to obtain full-field measurements using a dedicated post-processing algorithm. Finally, is presented a comparison between the experimental measurement and the numerical solution.

  15. Measurements of Photospheric and Chromospheric Magnetic Fields

    Science.gov (United States)

    Lagg, Andreas; Lites, Bruce; Harvey, Jack; Gosain, Sanjay; Centeno, Rebecca

    2017-09-01

    The Sun is replete with magnetic fields, with sunspots, pores and plage regions being their most prominent representatives on the solar surface. But even far away from these active regions, magnetic fields are ubiquitous. To a large extent, their importance for the thermodynamics in the solar photosphere is determined by the total magnetic flux. Whereas in low-flux quiet Sun regions, magnetic structures are shuffled around by the motion of granules, the high-flux areas like sunspots or pores effectively suppress convection, leading to a temperature decrease of up to 3000 K. The importance of magnetic fields to the conditions in higher atmospheric layers, the chromosphere and corona, is indisputable. Magnetic fields in both active and quiet regions are the main coupling agent between the outer layers of the solar atmosphere, and are therefore not only involved in the structuring of these layers, but also for the transport of energy from the solar surface through the corona to the interplanetary space. Consequently, inference of magnetic fields in the photosphere, and especially in the chromosphere, is crucial to deepen our understanding not only for solar phenomena such as chromospheric and coronal heating, flares or coronal mass ejections, but also for fundamental physical topics like dynamo theory or atomic physics. In this review, we present an overview of significant advances during the last decades in measurement techniques, analysis methods, and the availability of observatories, together with some selected results. We discuss the problems of determining magnetic fields at smallest spatial scales, connected with increasing demands on polarimetric sensitivity and temporal resolution, and highlight some promising future developments for their solution.

  16. Thermoluminescence measurement technique using millisecond temperature pulses.

    Science.gov (United States)

    Manfred, Michael E; Gabriel, Nicholas T; Yukihara, Eduardo G; Talghader, Joseph J

    2010-06-01

    A measurement technique, pulsed thermoluminescence, is described which uses short thermal pulses to excite trapped carriers leading to radiative recombination. The pulses are obtained using microstructures with approximately 500 micros thermal time constants. The technique has many of the advantages of pulsed optically stimulated luminescence without the need for optical sources and filters to isolate the luminescent signal. Charge carrier traps in alpha-Al(2)O(3):C particles on microheaters were filled using 205 nm light. Temperature pulses of 10 and 50 ms were applied to the heaters and compared with a standard thermoluminescence curve taken at a ramp rate of 5 K s(-1). This produced curves of intensity verses temperature similar to standard thermoluminescence except shifted to higher temperatures. The luminescence of single particles was read multiple times with negligible loss of population. The lower limit of the duration of useful pulses appears to be limited by particle size and thermal contact between the particle and heater.

  17. High impulse voltage and current measurement techniques fundamentals, measuring instruments, measuring methods

    CERN Document Server

    Schon, Klaus

    2013-01-01

    Equipment to be installed in electric power-transmission and distribution systems must pass acceptance tests with standardized high-voltage or high-current test impulses which simulate the stress on the insulation caused by external lightning discharges and switching operations in the grid. High impulse voltages and currents are also used in many other fields of science and engineering for various applications. Therefore, precise impulse-measurement techniques are necessary, either to prevent an over- or understressing of the insulation or to guarantee the effectiveness and quality of the application. The book deals with: principal generator circuits for generating high-voltage and high-current impulses measuring systems and their calibration according to IEC 60060 and IEC 62475 methods of estimating uncertainties of measurement mathematical and experimental basis for characterizing the transfer behavior of spatially extended systems used for measuring fast transients. This book is intended for engineers and ...

  18. Field methods for measuring concentrated flow erosion

    Science.gov (United States)

    Castillo, C.; Pérez, R.; James, M. R.; Quinton, J. N.; Taguas, E. V.; Gómez, J. A.

    2012-04-01

    Many studies have stressed the importance of gully erosion in the overall soil loss and sediment yield of agricultural catchments, for instance in recent years (Vandaele and Poesen, 1995; De Santisteban et al., 2006; Wu el al, 2008). Several techniques have been used for determining gully erosion in field studies. The conventional techniques involved the use of different devices (i.e. ruler, pole, tape, micro-topographic profilers, total station) to calculate rill and gully volumes through the determination of cross sectional areas and length of reaches (Casalí et al, 1999; Hessel and van Asch, 2003). Optical devices (i.e. laser profilemeters) have also been designed for the purpose of rapid and detailed assessment of cross sectional areas in gully networks (Giménez et al., 2009). These conventional 2d methods provide a simple and un-expensive approach for erosion evaluation, but are time consuming to carry out if a good accuracy is required. On the other hand, remote sensing techniques are being increasingly applied to gully erosion investigation such as aerial photography used for big-scale, long-term, investigations (e.g. Martínez-Casasnovas et al., 2004; Ionita, 2006), airborne and terrestrial LiDAR datasets for gully volume evaluation (James et al., 2007; Evans and Lindsay, 2010) and recently, major advances in 3D photo-reconstruction techniques (Welty et al. 2010, James et al., 2011). Despite its interest, few studies simultaneously compare the accuracies of the range of conventional and remote sensing techniques used, or define the most suitable method for a particular scale, given and time and cost constraints. That was the reason behind the International Workshop Innovations in the evaluation and measurement of rill and gully erosion, held in Cordoba in May 2011 and from which derive part of the materials presented in this abstract. The main aim of this work was to compare the accuracy and time requirements of traditional (2D) and recently developed

  19. Application of stereo photogrammetric techniques for measuring African Elephants

    Directory of Open Access Journals (Sweden)

    A. J Hall-Martin

    1979-01-01

    Full Text Available Measurements of shoulder height and back length of African elephants were obtained by means of stereo photogrammetric techniques. A pair of Zeiss UMK 10/1318 cameras, mounted on a steel frame on the back of a vehicle, were used to photograph the elephants in the Addo Elephant National Park, Republic of South Africa. Several modifications of normal photogrammetry procedure applicable to the field situation (eg. control points and the computation of results (eg. relative orientation are briefly mentioned. Six elephants were immobilised after being photographed and the measurements obtained from them agreed within a range of 1 cm-10 cm with the photogrammetric measurements.

  20. Uncertainty Analysis Technique for OMEGA Dante Measurements

    Energy Technology Data Exchange (ETDEWEB)

    May, M J; Widmann, K; Sorce, C; Park, H; Schneider, M

    2010-05-07

    The Dante is an 18 channel X-ray filtered diode array which records the spectrally and temporally resolved radiation flux from various targets (e.g. hohlraums, etc.) at X-ray energies between 50 eV to 10 keV. It is a main diagnostics installed on the OMEGA laser facility at the Laboratory for Laser Energetics, University of Rochester. The absolute flux is determined from the photometric calibration of the X-ray diodes, filters and mirrors and an unfold algorithm. Understanding the errors on this absolute measurement is critical for understanding hohlraum energetic physics. We present a new method for quantifying the uncertainties on the determined flux using a Monte-Carlo parameter variation technique. This technique combines the uncertainties in both the unfold algorithm and the error from the absolute calibration of each channel into a one sigma Gaussian error function. One thousand test voltage sets are created using these error functions and processed by the unfold algorithm to produce individual spectra and fluxes. Statistical methods are applied to the resultant set of fluxes to estimate error bars on the measurements.

  1. Alternative techniques for beam halo measurements

    CERN Document Server

    Welsch, CP; Burel, B; Lefèvre, T; Chapman, T; Pilon, MJ

    2006-01-01

    In future high intensity, high energy accelerators it must be ensured that particle losses are minimized, as activation of the vacuum chambers or other components makes maintenance and upgrade work time consuming and costly. It is imperative to have a clear understanding of the mechanisms that can lead to halo formation and to have the possibility to test available theoretical models with an adequate experimental setup. Measurements based on optical transition radiation (OTR) are a well-established technique for measurements of the transverse beam profile. However, in order to be suitable for halo measurements as well, the dynamic range of the final image acquisition system needs to be high, being able to cover at least five orders of magnitude in intensity changes. Here, the performance of a standard acquisition system as it is used in the CLIC test facility (CTF3) is compared to a step-by-step measurement with a small movable photo multiplier tube and an innovative camera system based on charge injection de...

  2. Defining and measuring transnational fields

    OpenAIRE

    Molina, J.; Petermann, S.; Herz, A.

    2012-01-01

    Transnational social fields and transnational social spaces are concepts used interchangeably in transnational literature. Although both of them refer to the complex of connections between borders, each of them represents a different – and complementary – perspective. In this paper, it will be argued that the adoption of the social networks approach by transnational studies actually inherited two different traditions for studying relational phenomena: the anthropological egocentric or persona...

  3. Erosive Burning Study Utilizing Ultrasonic Measurement Techniques

    Science.gov (United States)

    Furfaro, James A.

    2003-01-01

    A 6-segment subscale motor was developed to generate a range of internal environments from which multiple propellants could be characterized for erosive burning. The motor test bed was designed to provide a high Mach number, high mass flux environment. Propellant regression rates were monitored for each segment utilizing ultrasonic measurement techniques. These data were obtained for three propellants RSRM, ETM- 03, and Castor@ IVA, which span two propellant types, PBAN (polybutadiene acrylonitrile) and HTPB (hydroxyl terminated polybutadiene). The characterization of these propellants indicates a remarkably similar erosive burning response to the induced flow environment. Propellant burnrates for each type had a conventional response with respect to pressure up to a bulk flow velocity threshold. Each propellant, however, had a unique threshold at which it would experience an increase in observed propellant burn rate. Above the observed threshold each propellant again demonstrated a similar enhanced burn rate response corresponding to the local flow environment.

  4. Differential phase contrast 2.0-Opening new 'fields' for an established technique

    Energy Technology Data Exchange (ETDEWEB)

    Lohr, Matthias; Schregle, Ralph [Physics Faculty, Regensburg University, Universitaetsstrasse 31, D-93040 Regensburg (Germany); Jetter, Michael; Waechter, Clemens [Institute for Semiconductor Optics and Functional Interfaces, Stuttgart University, Pfaffenwaldring 57, D-70569 Stuttgart (Germany); Wunderer, Thomas; Scholz, Ferdinand [Institute for Optoelectronics, Ulm University, Albert-Einstein-Allee 45, D-89081 Ulm (Germany); Zweck, Josef, E-mail: josef.zweck@physik.uni-regensburg.de [Physics Faculty, Regensburg University, Universitaetsstrasse 31, D-93040 Regensburg (Germany)

    2012-06-15

    Differential phase contrast microscopy has become known as a high resolution imaging technique for magnetic micro-structures in the past. The method senses the local induction by measuring the deflection of the probe beam after it passes through a specimen area carrying a magnetic field. Little attention has been paid, however, to the fact that this technique is also capable of measuring electric fields. An application of the technique to measure piezoelectric polarization fields inside multi-layered structures such as quantum wells is demonstrated. For this purpose, piezoelectric fields within non-centrosymmetric crystal structures, based on GaN/InGaN/GaN quantum wells, are investigated. It can be shown that the technique is sensitive to these fields and yields detailed information about the field distribution. The specific information and experimental limitations as well as artefacts of the technique will be discussed in detail and first measurements are shown. The main advantages turn out to be high sensitivity for electric fields, combined with a very high resolution, which is limited only by the STEM probe size. Another advantage is the large achievable field of view. -- Highlights: Black-Right-Pointing-Pointer We describe a technique which allows the determination of inner electric fields in matter. Black-Right-Pointing-Pointer Inner fields are believed to be one major reason for the so-called efficiency 'droop' in green solid state lasers. Black-Right-Pointing-Pointer The technique used is differential phase contrast, used for the first time for inner electric field determination. Black-Right-Pointing-Pointer The technique is complementary to electron holography, offers a wider field of view and reveals new structures.

  5. Field scale measurements of NH3 emissions

    Science.gov (United States)

    Neftel, Albrecht; Ammann, Christof; Kuhn, Uwe; Sintermann, Jörg; Lehuger, Simon; Gärtner, Andrea; Hirschberger, Rainer

    2010-05-01

    The uncertainty in the ammonia emissions after application of organic manure contributes to a large extent to the overall uncertainties of the nitrogen budget of managed grassland systems (Ammann et al., 2009). Due to the sticky nature of the ammonia molecule and the variability of the emission fluxes the experimental determination is still a major challenge and a wide spread range of emission factors can be found in the literature. We report on two field experiments performed in August 2009 at the NitroEurope site in Oensingen, Switzerland. The ammonia emission flux after liquid manure application was investigated simultaneously by various micrometeorological methods: (1) a mass balance approach measuring the horizontal advection flux with open-path FTIR sensors (Gärtner et al., 2008), (2) aerodynamic gradient methods, and (3) eddy covariance measurements based on a novel fast ammonia analyser. Due to the sequential application of the manure and the fast decrease of the ammonia volatilisation, detailed footprint calculations (Neftel et al., 2008) and corrections with a high temporal resolution were crucial for obtaining representative emission fluxes. The plausibility of flux measurements has been evaluated with back trajectories simulations (WindTrax, Flesch et al., 2009). The results of all applied flux measurement methods confirmed the low emission levels found earlier by Spirig et al. (2009). A comparison of the field observations with results of process oriented models showed considerable differences in the temporal course of the ammonia emission indicating the need for improvements of the models. References: Ammann, C., Spirig, C., Leifeld, J. and Neftel, A.: Assessment of the nitrogen and carbon budget of two managed temperate grassland fields, Agric. Ecosyst. Environ., 133, 150-162, 2009. Flesch, T.K., Harper, L.A., Desjardins, R.L., Gao, Z., and Crenna, B.: Multi-Source Emission Determination Using an Inverse-Dispersion Technique. Boundary-Layer Meteorol

  6. Measures and dimensions of fractal sets in local fields

    Institute of Scientific and Technical Information of China (English)

    QIU Hua; SU Weiyi

    2006-01-01

    The study of fractal analysis over the local fields as underline spaces is very important since it can motivate new approaches and new ideas, and discover new techniques in the study of fractals. To study fractal sets in a local field K, in this paper, we define several kinds of fractal measures and dimensions of subsets in K. Some typical fractal sets in K are constructed. We also give out the Hausdorff dimensions and measures, Box-counting dimensions and Packing dimensions, and stress that there exist differences between fractal analysis on local fields and Euclidean spaces. Consequently, the theoretical foundation of fractal analysis on local fields is established.

  7. Antenna gain measurements in the intermediate-field zone

    Science.gov (United States)

    Anchidin, Liliana; Bari, Farida; Dumitrascu, Ana; Paun, Mirel; Deacu, Daniela; Tasu, Sorin; Danisor, Alin; Tamas, Razvan D.

    2016-12-01

    Antenna gain is usually evaluated under far-field conditions. Furthermore, Friis transmission formula can solely be applied when antenna size can be neglected with respect to the distance between the measuring antenna and the antenna under test. In this paper, we show that by applying the distance averaging technique the far-field and antenna size constraints can be overcome. Our method was validated by measuring a monopole antenna and a Vivaldi antenna in an open area test site (OATS).

  8. Emerging Raman Applications and Techniques in Biomedical and Pharmaceutical Fields

    CERN Document Server

    Morris, Michael D

    2010-01-01

    The book presents the latest technological advances in Raman spectroscopy that are presently redrawing the landscape of many fields of biomedical and pharmaceutical R&D. Numerous examples are given to illustrate the application of the new methods and compared with established and related techniques. The book is suitable for both new researchers and practitioners in this area as well as for those familiar with the Raman technique but seeking to keep abreast of the latest dramatic advances in this field.

  9. Full-field measurements and identification in solid mechanics

    CERN Document Server

    Grediac, Michel

    2008-01-01

    This timely book presents cutting-edge developments by experts in the field on the rapidly developing and scientifically challenging area of full-field measurement techniques used in solid mechanics - including photoelasticity, grid methods, deflectometry, holography, speckle interferometry and digital image correlation. The evaluation of strains and the use of the measurements in subsequent parameter identification techniques to determine material properties are also presented. Since parametric identification techniques require a close coupling of theoretical models and experimental measurements, the book focuses on specific modeling approaches that include finite element model updating, the equilibrium gap method, constitutive equation gap method, virtual field method and reciprocity gap method. In the latter part of the book, the authors discuss two particular applications of selected methods that are of special interest to many investigators: the analysis of localized phenomenon and connections between mi...

  10. Analyzing Extragalactic Magnetic Fields Using Faraday Rotation Measure Synthesis

    Science.gov (United States)

    Pare, Dylan; Wang, Q. Daniel; Kamieneski, Patrick; Sullivan, Kendall

    2017-01-01

    Extragalactic magnetic fields are a poorly understood element of galaxies that are likely to play an important role in galaxy formation and evolution. Until recently, however, there was no way to observe these fields to a high level of detail, making it difficult to map the spatial distribution of these fields to any high degree of accuracy. Fortunately, a new technique known as Faraday Rotation Measure Synthesis allows for a more precise analysis of galactic magnetism. This technique uses the observed Faraday rotation of polarized emission from background sources to map the magnetic field of a foreground galaxy. This Faraday rotation occurs when the polarized emission encounters ionized, magnetized gas within the galaxy, causing the emission to be rotated by an amount proportional the magnetic field subjected to the ionized gas. Working as part of CHANG-ES (Continuum HAlos in Nearby Galaxies - an EVLA Survey), we have applied this technique in order to learn about the distribution of magnetic fields in the disks and halos of edge-on spiral galaxies. We will present maps of the galactic magnetic fields of CHANG-ES galaxies using this technique, indicating the potential of this technique in successfully mapping these distant fields.

  11. Hybrid single-beam reconstruction technique for slow and fast varying wave fields.

    Science.gov (United States)

    Falaggis, Konstantinos; Kozacki, Tomasz; Kujawinska, Malgorzata

    2015-06-01

    An iterative single-beam wave field reconstruction technique that employs both non-paraxial, wave propagation based and paraxial deterministic phase retrieval techniques is presented. This approach overcomes two major obstacles that exist in the current state of the art techniques: iterative methods do not reconstruct slowly varying wave fields due to slow convergence and stagnation, and deterministic methods have paraxial limits, making the reconstructions of quickly varying object features impossible. In this work, a hybrid approach is reported that uses paraxial wave field corrections within iterative phase retrieval solvers. This technique is suitable for cases ranging from slow to fast varying wave fields, and unlike the currently available methods, can also reconstruct measurement objects with different regions of both slowly and quickly varying object features. It is further shown that this technique gives a higher accuracy than current single-beam phase retrieval techniques, and in comparison to the iterative methods, has a higher convergence speed.

  12. The FORS1 catalogue of stellar magnetic field measurements

    CERN Document Server

    Bagnulo, S; Landstreet, J D; Izzo, C

    2015-01-01

    The FORS1 instrument on the ESO Very Large Telescope was used to obtain low-resolution circular polarised spectra of nearly a thousand different stars, with the aim of measuring their mean longitudinal magnetic fields. A catalogue of FORS1 magnetic measurements would provide a valuable resource with which to better understand the strengths and limitations of this instrument and of similar low-dispersion, Cassegrain spectropolarimeters. However, FORS1 data reduction has been carried out by a number of different groups using a variety of reduction and analysis techniques. Our understanding of the instrument and our data reduction techniques have both improved over time. A full re-analysis of FORS1 archive data using a consistent and fully documented algorithm would optimise the accuracy and usefulness of a catalogue of field measurements. Based on the ESO FORS pipeline, we have developed a semi-automatic procedure for magnetic field determinations, which includes self-consistent checks for field detection relia...

  13. Sound Power Estimation by Laser Doppler Vibration Measurement Techniques

    Directory of Open Access Journals (Sweden)

    G.M. Revel

    1998-01-01

    Full Text Available The aim of this paper is to propose simple and quick methods for the determination of the sound power emitted by a vibrating surface, by using non-contact vibration measurement techniques. In order to calculate the acoustic power by vibration data processing, two different approaches are presented. The first is based on the method proposed in the Standard ISO/TR 7849, while the second is based on the superposition theorem. A laser-Doppler scanning vibrometer has been employed for vibration measurements. Laser techniques open up new possibilities in this field because of their high spatial resolution and their non-intrusivity. The technique has been applied here to estimate the acoustic power emitted by a loudspeaker diaphragm. Results have been compared with those from a commercial Boundary Element Method (BEM software and experimentally validated by acoustic intensity measurements. Predicted and experimental results seem to be in agreement (differences lower than 1 dB thus showing that the proposed techniques can be employed as rapid solutions for many practical and industrial applications. Uncertainty sources are addressed and their effect is discussed.

  14. Donnan membrane technique (DMT) for anion measurement.

    Science.gov (United States)

    Vega, Flora Alonso; Weng, Liping; Temminghoff, Erwin J M; Van Riemsdijk, Willem H

    2010-04-01

    Donnan membrane technique (DMT) is developed and tested for determination of free anion concentrations. Time needed to reach the Donnan membrane equilibrium depends on type of ions and the background. The Donnan membrane equilibrium is reached in 1 day for Cl(-), 1-2 days for NO(3)(-), 1-4 days for SO(4)(2-) and SeO(4)(2-), and 1-14 days for H(2)PO(4)(-) in a background of 2-200 mM KCl or K(2)SO(4). The strongest effect of ionic strength on equilibrium time is found for H(2)PO(4)(-), followed by SO(4)(2-) and SeO(4)(2-), and then by Cl(-) and NO(3)(-). The negatively charged organic particles of fulvic and humic acids do not pass the membrane. Two approaches for the measurement of different anion species of the same element, such as SeO(4)(2-) and HSeO(3)(-), using DMT are proposed and tested. These two approaches are based on transport kinetics or response to ionic strength difference. A transport model that was developed previously for cation DMT is applied in this work to analyze the rate-limiting step in the anion DMT. In the absence of mobile/labile complexes, transport tends to be controlled by diffusion in solution at a low ionic strength, whereas at a higher ionic strength, diffusion in the membrane starts to control the transport.

  15. Magnetic Field Measurement on a Refined Kicker

    CERN Document Server

    Fan, Tai-Ching; Lin, Fu-Yuan

    2005-01-01

    To prepare for the operation of top-up mode and increase the efficiency of injection at storage ring, National Synchrotron Radiation Research Center (NSRRC) has upgraded the kicker magnets and power supply. We have built up a new magnetic field measurement system to test the kicker. This system, including a search coil and a coil loop, can map the field and take the first integral of field automatically. We also simulate the trajectory of electron beam by pulsed wire method of field measurement. We analyze the performance of the kicker system in this paper.

  16. Basic phenomena utilised in aerosol particle measurement techniques; Hiukkasmittaustekniikoiden perusilmioet

    Energy Technology Data Exchange (ETDEWEB)

    Janka, K. [Dekati Oy, Tampere (Finland)

    2006-10-15

    The project deals with development of basic phenomena and mechanism utilised in aerosol particle measurement techniques. The areas under development are: particle-charging techniques, photoelectric charging, particle concentrating using virtual-impactor technique, and optical characterising techniques of particles. Results will be applied on detection techniques of bioaerosol attract, particle emission sensors for diesel exhaust gases, and widening the application areas of existing measurement techniques. (orig.)

  17. Attracting Students to the Field of Measurement

    Science.gov (United States)

    Finney, Sara J.; Pastor, Dena A.

    2012-01-01

    To address the shortage of professionals in measurement, it is essential that we make young career-seekers aware that measurement is an option as a profession. In this paper, we discuss how creating a strong pipeline of students into our field involves personal interactions between faculty representing the graduate programs in measurement and…

  18. Spectroscopic Measurement Techniques for Aerospace Flows

    Science.gov (United States)

    Danehy, Paul M.; Bathel, Brett F.; Johansen, Craig T.; Cutler, Andrew D.; Hurley, Samantha

    2014-01-01

    The conditions that characterize aerospace flows are so varied, that a single diagnostic technique is not sufficient for its measurement. Fluid dynamists use knowledge of similarity to help categorize and focus on different flow conditions. For example, the Reynolds number represents the ratio of inertial to viscous forces in a flow. When the velocity scales, length scales, and gas density are large and the magnitude of the molecular viscosity is low, the Reynolds number becomes large. This corresponds to large scale vehicles (e.g Airbus A380), fast moving objects (e.g. artillery projectiles), vehicles in dense fluids (e.g. submarine in water), or flows with low dynamic viscosity (e.g. skydiver in air). In each of these cases, the inertial forces dominate viscous forces, and unsteady turbulent fluctuations in the flow variables are observed. In contrast, flows with small length scales (e.g. dispersion of micro-particles in a solid rocket nozzle), slow moving objects (e.g. micro aerial vehicles), flows with low density gases (e.g. atmospheric re-entry), or fluids with a large magnitude of viscosity (e.g. engine coolant flow), all have low Reynolds numbers. In these cases, viscous forces become very important and often the flows can be steady and laminar. The Mach number, which is the ratio of the velocity to the speed of sound in the medium, also helps to differentiate types of flows. At very low Mach numbers, acoustic waves travel much faster than the object, and the flow can be assumed to be incompressible (e.g. Cessna 172 aircraft). As the object speed approaches the speed of sound, the gas density can become variable (e.g. flow over wing of Learjet 85). When the object speed is higher than the speed of sound (Ma > 1), the presences of shock waves and other gas dynamic features can become important to the vehicle performance (e.g. SR-71 Blackbird). In the hypersonic flow regime (Ma > 5), large changes in temperature begin to affect flow properties, causing real

  19. LIF Diagnostic for Measuring Beam-Transport Magnetic Fields

    Science.gov (United States)

    Jones, T. G.; Hinshelwood, D. D.; Neri, J. M.; Ottinger, P. F.; Noonan, W. A.

    1997-11-01

    A novel, spatially-resolved diagnostic is being developed to measure magnetic fields associated with intense ion beam propagation through a low-pressure gas, as is envisioned for light ion-driven ICF. The diagnostic technique uses laser-induced fluorescence (LIF) spectroscopy, and can be varied to measure either small or large fields. Small fields, as expected in ballistic transport with solenoidal lens focusing using ~ 1 Torr gas, produce Zeeman shifts, Δ λ_Z, smaller than the transition linewidth, Δ λ. High sensitivity to measure these shifts is achieved by a variation on the Babcock technique.^1 Large fields, as expected in self-pinched transport using 1--100 mTorr gas, produce Δ λZ larger than Δ λ. These Δ λZ will be resolved using an etalon as a narrowband, high-throughput optical filter. Available results from benchtop experiments using calibrated B-fields for both the small- and large-field techniques, and progress in fielding this diagnostic on the Gamble-II accelerator for beam-transport studies will be presented. Work supported by DOE through Sandia National Laboratories. ^ National Research Council Research Associate. ^ Present address University of Maryland, College Park, MD. ^1 W.A. Noonan, et al., Rev. Sci. Instrum. 68, 1032 (1997).

  20. International Conference Automation : Challenges in Automation, Robotics and Measurement Techniques

    CERN Document Server

    Zieliński, Cezary; Kaliczyńska, Małgorzata

    2016-01-01

    This book presents the set of papers accepted for presentation at the International Conference Automation, held in Warsaw, 2-4 March of 2016. It presents the research results presented by top experts in the fields of industrial automation, control, robotics and measurement techniques. Each chapter presents a thorough analysis of a specific technical problem which is usually followed by numerical analysis, simulation, and description of results of implementation of the solution of a real world problem. The presented theoretical results, practical solutions and guidelines will be valuable for both researchers working in the area of engineering sciences and for practitioners solving industrial problems. .

  1. Review of neutron calibration facilities and monitoring techniques: new needs for emerging fields.

    Science.gov (United States)

    Gressier, V

    2014-10-01

    Neutron calibration facilities and monitoring techniques have been developed since the middle of the 20th century to support research and nuclear power energy development. The technical areas needing reference neutron fields and related instruments were mainly cross section measurements, radiation protection, dosimetry and fission reactors, with energy ranging from a few millielectronvolts to about 20 MeV. The reference neutron fields and calibration techniques developed for these purposes will be presented in this paper. However, in recent years, emerging fields have brought new needs for calibration facilities and monitoring techniques. These new challenges for neutron metrology will be exposed with their technical difficulties.

  2. High-field bipolar loss measurement apparatus

    Science.gov (United States)

    Weldon, D.; Thullen, P.; Wollan, J.

    1980-09-01

    An apparatus was constructed to measure dissipation in superconducting wire in high alternating fields. The circuit incorporates a pair of locomotive traction motors as the capacitive circuit element for the bipolar swing. The design, construction and operating characteristics of the field coil and the associated circuitry are described.

  3. A method for longitudinal relaxation time measurement in inhomogeneous fields

    Science.gov (United States)

    Chen, Hao; Cai, Shuhui; Chen, Zhong

    2017-08-01

    The spin-lattice relaxation time (T1) plays a crucial role in the study of spin dynamics, signal optimization and data quantification. However, the measurement of chemical shift-specific T1 constants is hampered by the magnetic field inhomogeneity due to poorly shimmed external magnetic fields or intrinsic magnetic susceptibility heterogeneity in samples. In this study, we present a new protocol to determine chemical shift-specific T1 constants in inhomogeneous fields. Based on intermolecular double-quantum coherences, the new method can resolve overlapped peaks in inhomogeneous fields. The measurement results are in consistent with the measurements in homogeneous fields using the conventional method. Since spatial encoding technique is involved, the experimental time for the new method is very close to that for the conventional method. With the aid of T1 knowledge, some concealed information can be exploited by T1 weighting experiments.

  4. Optical metrology techniques for dimensional stability measurements

    NARCIS (Netherlands)

    Ellis, Jonathan David

    2010-01-01

    This thesis work is optical metrology techniques to determine material stability. In addition to displacement interferometry, topics such as periodic nonlinearity, Fabry-Perot interferometry, refractometry, and laser stabilization are covered.

  5. Optical metrology techniques for dimensional stability measurements

    NARCIS (Netherlands)

    Ellis, Jonathan David

    2010-01-01

    This thesis work is optical metrology techniques to determine material stability. In addition to displacement interferometry, topics such as periodic nonlinearity, Fabry-Perot interferometry, refractometry, and laser stabilization are covered.

  6. Lightning Magnetic Field Measurements around Langmuir Laboratory

    Science.gov (United States)

    Stock, M.; Krehbiel, P. R.; Rison, W.; Aulich, G. D.; Edens, H. E.; Sonnenfeld, R. G.

    2010-12-01

    In the absence of artificial conductors, underground lightning transients are produced by diffusion of the horizontal surface magnetic field of a return stroke vertically downward into the conducting earth. The changing magnetic flux produces an orthogonal horizontal electric field, generating a dispersive, lossy transverse electromagnetic wave that penetrates a hundred meters or more into the ground according to the skin depth of the medium. In turn, the electric field produces currents that flow toward or away from the channel to ground depending on the stroke polarity. The underground transients can produce large radial horizontal potential gradients depending on the distance from the discharge and depth below the surface. In this study we focus on the surface excitation field. The goal of the work is to compare measurements of surface magnetic field waveforms B(t) at different distances from natural lightning discharges with simple and detailed models of the return stroke fields. In addition to providing input to the diffusion mechanism, the results should aid in further understanding return stroke field generation processes. The observational data are to be obtained using orthogonal sets of straightened Rogowski coils to measure magnetic field waveforms in N-S and E-W directions. The waveforms are sampled at 500 kS/s over 1.024 second time intervals and recorded directly onto secure digital cards. The instrument operates off of battery power for several days or weeks at a time in remote, unattended locations and measures magnetic field strengths of up to several tens of amperes/meter. The observations are being made in conjunction with collocated slow electric field change measurements and under good 3-D lightning mapping array (LMA) and fast electric field change coverage.

  7. Repeated High-Precision Gravity and GPS Measurement Techniques

    Science.gov (United States)

    Gettings, P.; Harris, R. N.; Allis, R.; Chapman, D. S.

    2003-12-01

    Repeated high-precision gravity and GPS measurements are becoming a common tool for tracking changes in subsurface reservoirs. Despite this, there is little literature which discusses measurement techniques and the expected errors. Our research has focused on improving measurement techniques to be applied to ground water and geothermal steam reservoirs, including quantifying the minimum error levels with modern equipment. We applied these methods in two studies: ground water monitoring of the southern Salt Lake valley, Utah, USA, and steam monitoring of The Geysers geothermal field, California, USA. Gravity measurements using modern relative high-precision meters, such as Scintrex CG-3Ms or L&R E series, can now be routinely made to an accuracy of 5 μ Gal. Such accuracy requires the use of time series analysis at each station, and non-linear instrument drift functions. Modern computerized meters are capable of internally storing a time series of measurements for each station; older meters can often be fitted to log such data to a field computer. This time series, typically of 10-15 minute duration in our work, can then be analyzed in several ways to produce stable estimates of the gravity reading. In particular, our research has emphasized using a weighted arithmetic average (for long occupations), or a Thiele extrapolation scheme (for shorter station occupations). Instrument drift is removed through a superposition of a linear long-term drift function, and an empirical staircase function formed from differences between repeated station occupations. To achieve high-accuracy GPS measurements while maximizing the number of field stations in a survey, rapid-static measurements are necessary. We have tested the effect of occupation time and processing schemes on the absolute accuracy of the resulting GPS position. Using a post-processing differential method with a fixed (but not necessarily continuous) base station within 15 km, positioning error of <4 cm vertical is

  8. The Virtual Fields Method Extracting Constitutive Mechanical Parameters from Full-field Deformation Measurements

    CERN Document Server

    Pierron, Fabrice

    2012-01-01

    The Virtual Fields Method: Extracting Constitutive Mechanical Parameters from Full-field Deformation Measurements is the first book on the Virtual Fields Method (VFM), a technique to identify materials mechanical properties from full-field measurements. Firmly rooted with extensive theoretical description of the method, the book presents numerous examples of application to a wide range of materials (composites, metals, welds, biomaterials) and situations (static, vibration, high strain rate). The authors give a detailed training section with examples of progressive difficulty to lead the reader to program the VFM and include a set of commented Matlab programs as well as GUI Matlab-based software for more general situations. The Virtual Fields Method: Extracting Constitutive Mechanical Parameters from Full-field Deformation Measurements is an ideal book for researchers, engineers, and students interested in applying the VFM to new situations motivated by their research.  

  9. Electromagnetic techniques for industrial plant process measurements and quality control

    Energy Technology Data Exchange (ETDEWEB)

    Bramanti, M. (Consiglio Nazionale delle Ricerche, Pisa (Italy). Ist. di Elaborazione della Informazione)

    1992-04-01

    In recent years, new real time non-destructive measuring techniques have been developed based on the use of miniaturized components capable of generating, amplifying and elaborating microwave signals (within the range of tenths of a volt and hundreds of milliamps). All these techniques for the measurement of typical process parameters or the non-destructive testing of materials are based on the interaction of radiation with the material or system under examination and make use of the most modern types of data acquisition technology. This article surveys the sensors and measuring instruments which make use of electromagnetic radiation to acquire information concerning the properties of an examined material or system based on their interactions with electromagnetic fields. A few applications are illustrated, e.g., the measurement of unburnt coal in power plant fly ash, the measurement of the quantity of solid particles present in fluidized beds and the verification of the properties of dielectric materials. In each case, the optimum degree of resolution of these devices is made evident.

  10. Sound field separation technique with double holographic planes and its applications in acoustic holography

    Institute of Scientific and Technical Information of China (English)

    YU Fei; CHEN Jian; CHEN Xinzhao

    2004-01-01

    Sound field separation technique with double holographic planes is proposed, which overcomes the limitation on applications of near-field acoustic holography (NAH) and broadband acoustic holography from intensity measurement (BAHIM). The limitation is that sound field on one side of holographic plane must be free, that is to say, all the sound sources must be confined to the other side; but it is not easy to achieve for industrial measurements. The technique builds the sound field separation formula in wave number domain according to the wave field extrapolation theorem, and the sound pressure caused by sources on one side of holographic plane can be obtained as expected by taking two-dimensional Fourier transform of the formula. The derivation of the principle verifies the technique theoretically. The numerical simulations demonstrate its feasibility and effectiveness.

  11. Field results of antifouling techniques for optical instruments

    Science.gov (United States)

    Strahle, W.J.; Hotchkiss, F.S.; Martini, M.A.

    1998-01-01

    An anti-fouling technique is developed for the protection of optical instruments from biofouling which leaches a bromide compound into a sample chamber and pumps new water into the chamber prior to measurement. The primary advantage of using bromide is that it is less toxic than the metal-based antifoulants. The drawback of the bromide technique is also discussed.

  12. Skymapping with OSSE via the Mean Field Annealing Pixon Technique

    CERN Document Server

    Dixon, D D; Zych, A D; Cheng, L X; Johnson, W N; Kurfess, J D; Pina, R K; Pütter, R C; Purcell, W R; Wheaton, W A; Wheaton, Wm. A.

    1997-01-01

    We present progress toward using scanned OSSE observations for mapping and sky survey work. To this end, we have developed a technique for detecting pointlike sources of unknown number and location, given that they appear in a background which is relatively featureless or which can be modeled. The technique, based on the newly developed concept and mean field annealing, is described, with sample reconstructions of data from the OSSE Virgo Survey. The results demonstrate the capability of reconstructing source information without any a priori information about the number and/or location of pointlike sources in the field-of-view.

  13. Wideband scalable probe for Spherical Near-Field Antenna measurements

    DEFF Research Database (Denmark)

    Kim, Oleksiy S.; Pivnenko, Sergey; Breinbjerg, Olav

    2011-01-01

    The paper presents a design of an open-boundary quad-ridged horn to be used as a wideband scalable dual-linearly polarized probe for spherical near-field antenna measurements. With a new higher-order probe correction technique developed at the Technical University of Denmark, the probe will enabl...

  14. Sampling Criterion for EMC Near Field Measurements

    DEFF Research Database (Denmark)

    Franek, Ondrej; Sørensen, Morten; Ebert, Hans;

    2012-01-01

    An alternative, quasi-empirical sampling criterion for EMC near field measurements intended for close coupling investigations is proposed. The criterion is based on maximum error caused by sub-optimal sampling of near fields in the vicinity of an elementary dipole, which is suggested as a worst......-case representative of a signal trace on a typical printed circuit board. It has been found that the sampling density derived in this way is in fact very similar to that given by the antenna near field sampling theorem, if an error less than 1 dB is required. The principal advantage of the proposed formulation is its...... parametrization with respect to the desired maximum error in measurements. This allows the engineer performing the near field scan to choose a suitable compromise between accuracy and measurement time....

  15. Diagnostic techniques for measuring suprathermal electron dynamics in plasmas (invited).

    Science.gov (United States)

    Coda, S

    2008-10-01

    Plasmas, both in the laboratory and in space, are often not in thermodynamic equilibrium, and the plasma electron distribution function is accordingly non-Maxwellian. Suprathermal electron tails can be generated by external drives, such as rf waves and electric fields, or internal ones, such as instabilities and magnetic reconnection. The variety and importance of the phenomena in which suprathermal electrons play a significant role explains an enduring interest in diagnostic techniques to investigate their properties and dynamics. X-ray bremsstrahlung emission has been studied in hot magnetized plasmas for well over two decades, flanked progressively by electron-cyclotron emission in geometries favoring the high-energy end of the distribution function (high-field-side, vertical, oblique emission), by electron-cyclotron absorption, by spectroscopic techniques, and at lower temperatures, by Langmuir probes and electrostatic analyzers. Continuous progress in detector technology and in measurement and analysis techniques, increasingly sophisticated layouts (multichannel and tomographic systems, imaging geometries), and highly controlled suprathermal generation methods (e.g., perturbative rf modulation) have all been brought to bear in recent years on an increasingly detailed, although far from complete, understanding of suprathermal electron dynamics.

  16. Wheatstone bridge technique for magnetostriction measurements.

    Science.gov (United States)

    Sullivan, M

    1980-03-01

    A basic Wheatstone bridge, with additional electronic instrumentation, has been used in the measurement of magnetostriction. This method allows a resolution of approximately 10% on measurements of magnetostrictions less than 0.75 parts per million.

  17. Field flow fractionation techniques to explore the "nano-world".

    Science.gov (United States)

    Contado, Catia

    2017-04-01

    Field flow fractionation (FFF) techniques are used to successfully characterize several nanomaterials by sizing nano-entities and producing information about the aggregation/agglomeration state of nanoparticles. By coupling FFF techniques to specific detectors, researchers can determine particle-size distributions (PSDs), expressed as mass-based or number-based PSDs. This review considers FFF applications in the food, biomedical, and environmental sectors, mostly drawn from the past 4 y. It thus underlines the prominent role of asymmetrical flow FFF within the FFF family. By concisely comparing FFF techniques with other techniques suitable for sizing nano-objects, the advantages and the disadvantages of these instruments become clear. A consideration of select recent publications illustrates the state of the art of some lesser-known FFF techniques and innovative instrumental set-ups.

  18. Measuring sound absorption using local field assumptions

    NARCIS (Netherlands)

    Kuipers, E.R.

    2013-01-01

    To more effectively apply acoustically absorbing materials, it is desirable to measure angle-dependent sound absorption coefficients, preferably in situ. Existing measurement methods are based on an overall model of the acoustic field in front of the absorber, and are therefore sensitive to

  19. Technique for Measuring Hybrid Electronic Component Reliability

    Energy Technology Data Exchange (ETDEWEB)

    Green, C.C.; Hernandez, C.L.; Hosking, F.M.; Robinson, D.; Rutherford, B.; Uribe, F.

    1999-01-01

    Materials compatibility studies of aged, engineered materials and hardware are critical to understanding and predicting component reliability, particularly for systems with extended stockpile life requirements. Nondestructive testing capabilities for component reliability would significantly enhance lifetime predictions. For example, if the detection of crack propagation through a solder joint can be demonstrated, this technique could be used to develop baseline information to statistically determine solder joint lifelengths. This report will investigate high frequency signal response techniques for nondestructively evaluating the electrical behavior of thick film hybrid transmission lines.

  20. Determination of the optimal method for the field-in-field technique in breast tangential radiotherapy.

    Science.gov (United States)

    Tanaka, Hidekazu; Hayashi, Shinya; Hoshi, Hiroaki

    2014-07-01

    Several studies have reported the usefulness of the field-in-field (FIF) technique in breast radiotherapy. However, the methods for the FIF technique used in these studies vary. These methods were classified into three categories. We simulated a radiotherapy plan with each method and analyzed the outcomes. In the first method, a pair of subfields was added to each main field: the single pair of subfields method (SSM). In the second method, three pairs of subfields were added to each main field: the multiple pairs of subfields method (MSM). In the third method, subfields were alternately added: the alternate subfields method (ASM). A total of 51 patients were enrolled in this study. The maximum dose to the planning target volume (PTV) (Dmax) and the volumes of the PTV receiving 100% of the prescription dose (V100%) were calculated. The thickness of the breast between the chest wall and skin surface was measured, and patients were divided into two groups according to the median. In the overall series, the average V100% with ASM (60.3%) was significantly higher than with SSM (52.6%) and MSM (48.7%). In the thin breast group as well, the average V100% with ASM (57.3%) and SSM (54.2%) was significantly higher than that with MSM (43.3%). In the thick breast group, the average V100% with ASM (63.4%) was significantly higher than that with SSM (51.0%) and MSM (54.4%). ASM resulted in better dose distribution, regardless of the breast size. Moreover, planning for ASM required a relatively short time. ASM was considered the most preferred method.

  1. On the theory of SODAR measurement techniques

    DEFF Research Database (Denmark)

    Antoniou, I.; Ejsing Jørgensen, Hans; Bradley, S.

    2003-01-01

    The need for alternative means to measure the wind speed for wind energy purposes has increased with the increase of the size of wind turbines. The cost and the technical difficulties for performing wind speed measurements has also increased with the sizeof the wind turbines, since it is demanded...... of measuring both the wind speed distribution with height and the wind direction. At the same time the SODAR presents a number of serious drawbacks such asthe low number of measurements per time period, the dependence of the ability to measure on the atmospheric conditions and the difficulty of measuring...... that the wind speed has to be measured at the rotor centre of the turbine and the size of both the rotor and the hub height have grown following the increase in the size of the wind turbines. The SODAR (SOundDetection And Ranging) is an alternative to the use of cup anemometers and offers the possibility...

  2. Perspective of remote optical measurement techniques

    OpenAIRE

    Gregorio, Eduard; Rocadenbosch Burillo, Francisco

    2007-01-01

    This article presents an intercomparison between four different ROMTs: differential optical absorption spectroscopy (DOAS), differential absorption LIDAR (DIAL), Fourier transform infrared spectroscopy (FTIR), and tunable diode laser absorption spectroscopy (TDLAS). The main focus is on the TDLAS technique, where the main laser-diode typologies and modulation schemes, namely, wavelength modulation spectroscopy (WMS) and frequency modulation spectroscopy (FMS), are reviewed. At present, new pr...

  3. Donnan Membrane Technique (DMT) for Anion Measurement

    NARCIS (Netherlands)

    Alonso Vega, M.F.; Weng, L.P.; Temminghoff, E.J.M.; Riemsdijk, van W.H.

    2010-01-01

    Donnan membrane technique (DMT) is developed and tested for determination of free anion concentrations. Time needed to reach the Donnan membrane equilibrium depends on type of ions and the background. The Donnan membrane equilibrium is reached in 1 day for Cl-, 1-2 days for NO3-, 1-4 days for SO42-

  4. Measurements of 222Rn, 220Rn, and CO2 Emissions in Natural CO2 Fields in Wyoming: MVA Techniques for Determining Gas Transport and Caprock Integrity

    Energy Technology Data Exchange (ETDEWEB)

    Kaszuba, John; Sims, Kenneth

    2014-09-30

    An integrated field-laboratory program evaluated the use of radon and CO2 flux measurements to constrain source and timescale of CO2 fluxes in environments proximate to CO2 storage reservoirs. By understanding the type and depth of the gas source, the integrity of a CO2 storage reservoir can be assessed and monitored. The concept is based on correlations of radon and CO2 fluxes observed in volcanic systems. This fundamental research is designed to advance the science of Monitoring, Verification, and Accounting (MVA) and to address the Carbon Storage Program goal of developing and validating technologies to ensure 99 percent storage performance. Graduate and undergraduate students conducted the research under the guidance of the Principal Investigators; in doing so they were provided with training opportunities in skills required for implementing and deploying CCS technologies. Although a final method or “tool” was not developed, significant progress was made. The field program identified issues with measuring radon in environments rich in CO2. Laboratory experiments determined a correction factor to apply to radon measurements made in CO2-bearing environments. The field program also identified issues with radon and CO2-flux measurements in soil gases at a natural CO2 analog. A systematic survey of radon and CO2 flux in soil gases at the LaBarge CO2 Field in Southwest Wyoming indicates that measurements of 222Rn (radon), 220Rn (thoron), and CO2 flux may not be a robust method for monitoring the integrity of a CO2 storage reservoir. The field program was also not able to correlate radon and CO2 flux in the CO2-charged springs of the Thermopolis hydrothermal system. However, this part of the program helped to motivate the aforementioned laboratory experiments that determined

  5. Micro analysis of fringe field formed inside LDA measuring volume

    Science.gov (United States)

    Ghosh, Abhijit; Nirala, A. K.

    2016-05-01

    In the present study we propose a technique for micro analysis of fringe field formed inside laser Doppler anemometry (LDA) measuring volume. Detailed knowledge of the fringe field obtained by this technique allows beam quality, alignment and fringe uniformity to be evaluated with greater precision and may be helpful for selection of an appropriate optical element for LDA system operation. A complete characterization of fringes formed at the measurement volume using conventional, as well as holographic optical elements, is presented. Results indicate the qualitative, as well as quantitative, improvement of fringes formed at the measurement volume by holographic optical elements. Hence, use of holographic optical elements in LDA systems may be advantageous for improving accuracy in the measurement.

  6. Development of Improved Oil Field Waste Injection Disposal Techniques

    Energy Technology Data Exchange (ETDEWEB)

    Terralog Technologies

    2002-11-25

    The goals of this project have was to: (1) assemble and analyze a comprehensive database of past waste injection operations; (2) develop improved diagnostic techniques for monitoring fracture growth and formation changes; (3) develop operating guidelines to optimize daily operations and ultimate storage capacity of the target formation; and (4) to apply these improved models and guidelines in the field.

  7. Seismic techniques of enhanced oil recovery: experimental and field results

    Energy Technology Data Exchange (ETDEWEB)

    Kuznetsov, O.L.; Simkin, E.M.; Chilingar, G.V.; Gorfunkel, M.V.; Robertson, J.O. Jr.

    2002-09-15

    Application of secondary and tertiary oil recovery techniques during late field development stages usually yields poor results. The reasons are principally due to the low efficiency of these technologies, probably because the gravity and capillary forces are not properly considered. Improved efficiency for hydrocarbon recovery produced by seismic vibration is discussed. (author)

  8. High precision simulation techniques for lattice field theory

    CERN Document Server

    Wolff, U

    1993-01-01

    An overview is given over the recently developed and now widely used Monte Carlo algorithms with reduced or eliminated critical slowing down. The basic techniques are overrelaxation, cluster algorithms and multigrid methods. With these tools one is able to probe much closer than before the universal continuum behavior of field theories on the lattice.

  9. Teaching Avalanche Safety Courses: Instructional Techniques and Field Exercises.

    Science.gov (United States)

    Watters, Ron

    This paper discusses course structure, teaching techniques, and field exercises for enhancing winter travelers' avalanche knowledge and skills. In two class sessions, the course typically consists of a historical perspective; a section on snow physics (clouds, types of snow crystals, effects of riming, identification of precipitated snow crystals,…

  10. Nonlinear ultrasonic measurements based on cross-correlation filtering techniques

    Science.gov (United States)

    Yee, Andrew; Stewart, Dylan; Bunget, Gheorghe; Kramer, Patrick; Farinholt, Kevin; Friedersdorf, Fritz; Pepi, Marc; Ghoshal, Anindya

    2017-02-01

    Cyclic loading of mechanical components promotes the formation of dislocation dipoles in metals, which can serve as precursors to crack nucleation and ultimately lead to failure. In the laboratory setting, an acoustic nonlinearity parameter has been assessed as an effective indicator for characterizing the progression of fatigue damage precursors. However, the need to use monochromatic waves of medium-to-high acoustic energy has presented a constraint, making it problematic for use in field applications. This paper presents a potential approach for field measurement of acoustic nonlinearity by using general purpose ultrasonic pulser-receivers. Nonlinear ultrasonic measurements during fatigue testing were analyzed by the using contact and immersion pulse-through method. A novel cross-correlation filtering technique was developed to extract the fundamental and higher harmonic waves from the signals. As in the case of the classic harmonic generation, the nonlinearity parameters of the second and third harmonics indicate a strong correlation with fatigue cycles. Consideration was given to potential nonlinearities in the measurement system, and tests have confirmed that measured second harmonic signals exhibit a linear dependence on the input signal strength, further affirming the conclusion that this parameter relates to damage precursor formation from cyclic loading.

  11. Mean field spin glasses treated with PDE techniques

    Science.gov (United States)

    Barra, Adriano; Del Ferraro, Gino; Tantari, Daniele

    2013-07-01

    Following an original idea of Guerra, in these notes we analyze the Sherrington-Kirkpatrick model from different perspectives, all sharing the underlying approach which consists in linking the resolution of the statistical mechanics of the model (e.g. solving for the free energy) to well-known partial differential equation (PDE) problems (in suitable spaces). The plan is then to solve the related PDE using techniques involved in their native field and lastly bringing back the solution in the proper statistical mechanics framework. Within this strand, after a streamlined test-case on the Curie-Weiss model to highlight the methods more than the physics behind, we solve the SK both at the replica symmetric and at the 1-RSB level, obtaining the correct expression for the free energy via an analogy to a Fourier equation and for the self-consistencies with an analogy to a Burger equation, whose shock wave develops exactly at critical noise level (triggering the phase transition). Our approach, beyond acting as a new alternative method (with respect to the standard routes) for tackling the complexity of spin glasses, links symmetries in PDE theory with constraints in statistical mechanics and, as a novel result from the theoretical physics perspective, we obtain a new class of polynomial identities (namely of Aizenman-Contucci type, but merged within the Guerra's broken replica measures), whose interest lies in understanding, via the recent Panchenko breakthroughs, how to force the overlap organization to the ultrametric tree predicted by Parisi.

  12. [Authentication of Trace Material Evidence in Forensic Science Field with Infrared Microscopic Technique].

    Science.gov (United States)

    Jiang, Zhi-quan; Hu, Ke-liang

    2016-03-01

    In the field of forensic science, conventional infrared spectral analysis technique is usually unable to meet the detection requirements, because only very a few trace material evidence with diverse shapes and complex compositions, can be extracted from the crime scene. Infrared microscopic technique is developed based on a combination of Fourier-transform infrared spectroscopic technique and microscopic technique. Infrared microscopic technique has a lot of advantages over conventional infrared spectroscopic technique, such as high detection sensitivity, micro-area analysisand nondestructive examination. It has effectively solved the problem of authentication of trace material evidence in the field of forensic science. Additionally, almost no external interference is introduced during measurements by infrared microscopic technique. It can satisfy the special need that the trace material evidence must be reserved for witness in court. It is illustrated in detail through real case analysis in this experimental center that, infrared microscopic technique has advantages in authentication of trace material evidence in forensic science field. In this paper, the vibration features in infrared spectra of material evidences, including paints, plastics, rubbers, fibers, drugs and toxicants, can be comparatively analyzed by means of infrared microscopic technique, in an attempt to provide powerful spectroscopic evidence for qualitative diagnosis of various criminal and traffic accident cases. The experimental results clearly suggest that infrared microscopic technique has an incomparable advantage and it has become an effective method for authentication of trace material evidence in the field of forensic science.

  13. High-field bipolar loss measurement apparatus

    Energy Technology Data Exchange (ETDEWEB)

    Thullen, P.; Weldon, D.; Wollan, J.

    1980-01-01

    An apparatus was constructed to measure dissipation in superconducting wire in high alternating fields. The apparatus will be used to make measurements on conductors which must operate in fields up to 7.0 T and rates of field change up to 15 T/s. The magnet for this facility is wound of uninsulated, 15 strand Rutherford cable in which the strand is a 0.812 mm diameter, fully mixed matrix, Cu plus CuNi, multifilament NbTi conductor. The coil is wound in a bath cooled configuration with an overall current density of 7.8 kA/cm/sup 2/. The circuit incorporates a pair of locomotive traction motors as the capacitive circuit element for the bipolar swing. The design, construction and operating characteristics of the field coil and the associated circuitry are described.

  14. A Simple Technique for High Resistance Measurement

    Science.gov (United States)

    Aguilar, Horacio Munguia; Landin, Ramon Ochoa

    2012-01-01

    A simple electronic system for the measurement of high values of resistance is shown. This system allows the measurement of resistance in the range of a few megohm up to 10[superscript 9] [omega]. We have used this system for the evaluation of CdS thin film resistance, but other practical uses in the basic physics laboratory are presented.…

  15. A Simple Technique for High Resistance Measurement

    Science.gov (United States)

    Aguilar, Horacio Munguia; Landin, Ramon Ochoa

    2012-01-01

    A simple electronic system for the measurement of high values of resistance is shown. This system allows the measurement of resistance in the range of a few megohm up to 10[superscript 9] [omega]. We have used this system for the evaluation of CdS thin film resistance, but other practical uses in the basic physics laboratory are presented.…

  16. SPEED ROLLER STAND MEASUREMENT SYSTEM CHECKING TECHNIQUE

    OpenAIRE

    Zybtsev, Y.; I. Marmut

    2011-01-01

    The study has shown that the accuracy of brakes checking by inertial stands depends upon the applied methods of measurement of braking parameters (stand slowing down, braking distance, brakes triggering time, current speed) as well as the methods of metrological checking of measuring system canals.

  17. A simple technique for individual picosecond laser pulse duration measurements

    Science.gov (United States)

    Smith, W. L.; Bechtel, J. H.

    1976-01-01

    We describe here a simple nonlinear optic technique for the measurement of the duration of individual picosecond pulses. The accuracy and relative simplicity of the technique increase with the number of pulses measured. An experimental test of the basis of the technique is described.

  18. Advanced Techniques for Power System Identification from Measured Data

    Energy Technology Data Exchange (ETDEWEB)

    Pierre, John W.; Wies, Richard; Trudnowski, Daniel

    2008-11-25

    Time-synchronized measurements provide rich information for estimating a power-system's electromechanical modal properties via advanced signal processing. This information is becoming critical for the improved operational reliability of interconnected grids. A given mode's properties are described by its frequency, damping, and shape. Modal frequencies and damping are useful indicators of power-system stress, usually declining with increased load or reduced grid capacity. Mode shape provides critical information for operational control actions. This project investigated many advanced techniques for power system identification from measured data focusing on mode frequency and damping ratio estimation. Investigators from the three universities coordinated their effort with Pacific Northwest National Laboratory (PNNL). Significant progress was made on developing appropriate techniques for system identification with confidence intervals and testing those techniques on field measured data and through simulation. Experimental data from the western area power system was provided by PNNL and Bonneville Power Administration (BPA) for both ambient conditions and for signal injection tests. Three large-scale tests were conducted for the western area in 2005 and 2006. Measured field PMU (Phasor Measurement Unit) data was provided to the three universities. A 19-machine simulation model was enhanced for testing the system identification algorithms. Extensive simulations were run with this model to test the performance of the algorithms. University of Wyoming researchers participated in four primary activities: (1) Block and adaptive processing techniques for mode estimation from ambient signals and probing signals, (2) confidence interval estimation, (3) probing signal design and injection method analysis, and (4) performance assessment and validation from simulated and field measured data. Subspace based methods have been use to improve previous results from block

  19. Apparatus and techniques for measuring bedload

    Science.gov (United States)

    Hubbell, David Wellington

    1964-01-01

    The need for accurate determinations of the total sediment discharge of particles of bedload size has prompted this investigation of available and possible measuring apparatus and procedures. The accuracy of measurements of sediment discharge made with trap-type samplers is affected by the variability of sampler efficiency, by the oscillatory variation of bedload discharge, and by sampler placement. Equations that were developed for determining total discharge from measured bedioad discharge and measured suspended-sediment discharge are simplest if the bedload apparatus measures only the true bedload. Early bedload samplers are generally unsatisfactory. Recently developed or suggested apparatus include various improved samplers of the pressure-difference type, a pumping sampler, a magnetic sampler, acoustical instruments that measure the magnitude of the sound of particle collisions, an ultrasonic bedload sampler designed to measure and integrate electronically the concentration and velocity, and a tiltmeter designed to measure the total sediment discharge from the ground tilt that results from the passage of flow. All the pressure-difference samplers are improvements over early samplers, but none are void of the inherent shortcomings of trap-type apparatus; probably the Sphinx (Dutch) and VUV (Hungarian) samplers are the most satisfactory. The acoustical instruments are capable of measuring only the relative discharge. The ultrasonic sampler and the tiltmeter are not adequate without further development. Some new possible apparatus and means for measuring or aiding in measuring bedload discharge are small pit samplers, ultrasonic sounders, pressure transducers, and photography. A small pit sampler for measuring bedload discharge was designed to provide self-placement and portability ; however, its practicability and efficiency are undetermined. Exploratory films show that by using slowmotion photography the discharge of particles larger than about pea size can be

  20. Stratospheric electric field measurements with transmediterranean balloons

    Science.gov (United States)

    de La Morena, B. A.; Alberca, L. F.; Curto, J. J.; Holzworth, R. H.

    1993-01-01

    The horizontal component of the stratospheric electric field was measured using a balloon in the ODISEA Campaign of Transmediterranean Balloon Program. The balloon flew between Trapani (Sicily) and El Arenosillo (Huelva, Spain) along the 39 deg N parallel at a height between 34 and 24 km. The high values found for the field on fair-weather and its quasi-turbulent variation, both in amplitude and direction, are difficult to explain with the classical electric field source. A new source, first described by Holzworth (1989), is considered as possibly causing them.

  1. A Comprehensive Method of Estimating Electric Fields from Vector Magnetic Field and Doppler Measurements

    CERN Document Server

    Kazachenko, Maria D; Welsch, Brian T

    2014-01-01

    Photospheric electric fields, estimated from sequences of vector magnetic field and Doppler measurements, can be used to estimate the flux of magnetic energy (the Poynting flux) into the corona and as time-dependent boundary conditions for dynamic models of the coronal magnetic field. We have modified and extended an existing method to estimate photospheric electric fields that combines a poloidal-toroidal (PTD) decomposition of the evolving magnetic field vector with Doppler and horizontal plasma velocities. Our current, more comprehensive method, which we dub the "{\\bf P}TD-{\\bf D}oppler-{\\bf F}LCT {\\bf I}deal" (PDFI) technique, can now incorporate Doppler velocities from non-normal viewing angles. It uses the \\texttt{FISHPACK} software package to solve several two-dimensional Poisson equations, a faster and more robust approach than our previous implementations. Here, we describe systematic, quantitative tests of the accuracy and robustness of the PDFI technique using synthetic data from anelastic MHD (\\te...

  2. Semantic Data And Visualization Techniques Applied To Geologic Field Mapping

    Science.gov (United States)

    Houser, P. I. Q.; Royo-Leon, M.; Munoz, R.; Estrada, E.; Villanueva-Rosales, N.; Pennington, D. D.

    2015-12-01

    Geologic field mapping involves the use of technology before, during, and after visiting a site. Geologists utilize hardware such as Global Positioning Systems (GPS) connected to mobile computing platforms such as tablets that include software such as ESRI's ArcPad and other software to produce maps and figures for a final analysis and report. Hand written field notes contain important information and drawings or sketches of specific areas within the field study. Our goal is to collect and geo-tag final and raw field data into a cyber-infrastructure environment with an ontology that allows for large data processing, visualization, sharing, and searching, aiding in connecting field research with prior research in the same area and/or aid with experiment replication. Online searches of a specific field area return results such as weather data from NOAA and QuakeML seismic data from USGS. These results that can then be saved to a field mobile device and searched while in the field where there is no Internet connection. To accomplish this we created the GeoField ontology service using the Web Ontology Language (OWL) and Protégé software. Advanced queries on the dataset can be made using reasoning capabilities can be supported that go beyond a standard database service. These improvements include the automated discovery of data relevant to a specific field site and visualization techniques aimed at enhancing analysis and collaboration while in the field by draping data over mobile views of the site using augmented reality. A case study is being performed at University of Texas at El Paso's Indio Mountains Research Station located near Van Horn, Texas, an active multi-disciplinary field study site. The user can interactively move the camera around the study site and view their data digitally. Geologist's can check their data against the site in real-time and improve collaboration with another person as both parties have the same interactive view of the data.

  3. Pulsed beams as field probes for precision measurement

    OpenAIRE

    Hudson, J. J.; Ashworth, H. T.; Kara, D. M.; Tarbutt, M. R.; Sauer, B.E.; Hinds, E. A.

    2007-01-01

    We describe a technique for mapping the spatial variation of static electric, static magnetic, and rf magnetic fields using a pulsed atomic or molecular beam. The method is demonstrated using a beam designed to measure the electric dipole moment of the electron. We present maps of the interaction region, showing sensitivity to (i) electric field variation of 1.5 V/cm at 3.3 kV/cm with a spatial resolution of 15 mm; (ii) magnetic field variation of 5 nT with 25 mm resolution; (iii) radio-frequ...

  4. Measuring verbal psychotherapeutic techniques – A systematic review of intervention characteristics and measures

    Directory of Open Access Journals (Sweden)

    Antje eGumz

    2015-11-01

    Full Text Available Language is one of the most important tools of psychotherapists. The working mechanisms of verbal therapeutic techniques, however, are still marginally understood. In part, this is due to the lack of a generally acknowledged typology as well as a gold standard for the assess-ment of verbal techniques, which limits the possibility of conducting studies focusing this topic. The present study reviews measures used in clinical research which assess directly ob-servable dimensions of verbal interventions in a reliable manner. All measures were evaluated with respect to their theoretical foundation, research goals, assessment modes, and various psychometric properties. A systematic search in databases (PubMed, PsycInfo, PsycArticles, PSYNDEX, Web of Science, Embase followed by an additional snowballing search cover-ing the years 1940-2013 yielded n=179 publications eligible for review. Within these publica-tions, 34 measures were identified showing great heterogeneity regarding the aspects under study. Only two measures reached the highest psychometric standards and can be recom-mended for clinical use without any reservation. Central problems include deficiencies in the systematization of techniques as well as their partly ambiguous and inconsistent definitions. To promote this field of research, it will be important to achieve a consensus concerning the terminology, conceptions and measures of verbal techniques.

  5. Electric Field Quantitative Measurement System and Method

    Science.gov (United States)

    Generazio, Edward R. (Inventor)

    2016-01-01

    A method and system are provided for making a quantitative measurement of an electric field. A plurality of antennas separated from one another by known distances are arrayed in a region that extends in at least one dimension. A voltage difference between at least one selected pair of antennas is measured. Each voltage difference is divided by the known distance associated with the selected pair of antennas corresponding thereto to generate a resulting quantity. The plurality of resulting quantities defined over the region quantitatively describe an electric field therein.

  6. Imaging interferometry to measure surface rotation field

    DEFF Research Database (Denmark)

    Travaillot, Thomas; Dohn, Søren; Boisen, Anja

    2013-01-01

    This paper describes a polarized-light imaging interferometer to measure the rotation field of reflecting surfaces. This setup is based on a homemade prism featuring a birefringence gradient. The arrangement is presented before focusing on the homemade prism and its manufacturing process....... The dependence of the measured optical phase on the rotation of the surface is derived, thus highlighting the key parameters driving the sensitivity. The system’s capabilities are illustrated by imaging the rotation field at the surface of a tip-loaded polymer specimen....

  7. Near-Field to Far-Field Transformation Techniques with Spiral Scannings: A Comprehensive Review

    Directory of Open Access Journals (Sweden)

    Renato Cicchetti

    2014-01-01

    Full Text Available An overview of the near-field-far-field (NF-FF transformation techniques with innovative spiral scannings, useful to derive the radiation patterns of the antennas commonly employed in the modern wireless communication systems, is provided in this paper. The theoretical background and the development of a unified theory of the spiral scannings for quasi-spherical and nonspherical antennas are described, and an optimal sampling interpolation expansion to evaluate the probe response on a quite arbitrary rotational surface from a nonredundant number of its samples, collected along a proper spiral wrapping it, is presented. This unified theory can be applied to spirals wrapping the conventional scanning surfaces and makes it possible to accurately reconstruct the NF data required by the NF-FF transformation employing the corresponding classical scanning. A remarkable reduction of the measurement time is so achieved, due to the use of continuous and synchronized movements of the positioning systems and to the reduced number of needed NF measurements. Some numerical and experimental results relevant to the spherical spiral scanning case when dealing with quasi-planar and electrically long antennas are shown.

  8. Chemonucleolysis technique. New oblique approach requires no measurements.

    Science.gov (United States)

    Romy, M

    1986-01-01

    The author describes a new technique for intradiscal therapy that eliminates the need for measurements. The new technique for entering the lumbar disk for discolysis from the oblique approach is described as simple, accurate and safe.

  9. Altertative trophy measuring techniques for African buffalo

    Directory of Open Access Journals (Sweden)

    S.E. Gandy

    2004-12-01

    Full Text Available The African buffalo is considered the classic African trophy. It is the choice of many hunters who will never go on to hunt any of the other dangerous game animals on the continent. A good trophy is perceived as that of a mature bull with a hardened boss and horn tips that lengthen into sharply pointed hooks. However, indications are that these are the bulls in their breeding prime and there is concern that the continued targeting of these individuals will negatively impact on the population dynamics of the herds, ultimately affecting the sustainability of buffalo hunting. As they age and become postreproductive, the horns broom down, reducing the trophy score under the current measurement systems. A new measuring system is needed that encourages hunters to target the older post-reproductive bulls, instead of those that are still breeding. A random sample of trophies was divided into broomed and non-broomed sub-samples. All key parameters that can be measured in the trophy were measured with a view to identifying the parameters that would allow broomed-down individuals to compete favourably with the non-broomed “classic trophy” in the primary measurement systems, those of Safari Club International and Rowland Ward. An index, created through dividing tip space by the mean of the two individual horn lengths proved to serve the purpose. This factor was then applied to the mean of the SCI and Rowland Ward measurements in the samples. These methods allowed broomed horns to score more points in the record books than non-broomed horns. Boss width and boss space are other possible measurement inclusions that could be considered.

  10. Adaptive framework for uncertainty analysis in electromagnetic field measurements.

    Science.gov (United States)

    Prieto, Javier; Alonso, Alonso A; de la Rosa, Ramón; Carrera, Albano

    2015-04-01

    Misinterpretation of uncertainty in the measurement of the electromagnetic field (EMF) strength may lead to an underestimation of exposure risk or an overestimation of required measurements. The Guide to the Expression of Uncertainty in Measurement (GUM) has internationally been adopted as a de facto standard for uncertainty assessment. However, analyses under such an approach commonly assume unrealistic static models or neglect relevant prior information, resulting in non-robust uncertainties. This study proposes a principled and systematic framework for uncertainty analysis that fuses information from current measurements and prior knowledge. Such a framework dynamically adapts to data by exploiting a likelihood function based on kernel mixtures and incorporates flexible choices of prior information by applying importance sampling. The validity of the proposed techniques is assessed from measurements performed with a broadband radiation meter and an isotropic field probe. The developed framework significantly outperforms GUM approach, achieving a reduction of 28% in measurement uncertainty.

  11. Electric field measurements from Halley, Antarctica

    Science.gov (United States)

    Nicoll, Keri; Harrison, R. Giles

    2016-04-01

    Antarctica is a unique location for the study of atmospheric electricity. Not only is it one of the most pollutant free places on Earth, but its proximity to the south magnetic pole means that it is an ideal location to study the effects of solar variability on the atmospheric electric field. This is due to the reduced shielding effect of the geomagnetic field at the poles which leads to a greater flux of incoming Galactic Cosmic Rays (GCRs) as well as an increased probability of energetic particle precipitation from SEPs and relativistic electrons. To investigate such effects, two electric field mills of different design were installed at the British Antarctic Survey Halley base in February 2015 (75. 58 degrees south, 26.66 degrees west). Halley is situated on the Brunt Ice Shelf in the south east of the Weddell Sea and has snow cover all year round. Preliminary analysis has focused on selection of fair weather criteria using wind speed and visibility measurements which are vital to assess the effects of falling snow, blowing snow and freezing fog on the electric field measurements. When the effects of such adverse weather conditions are removed clear evidence of the characteristic Carnegie Curve diurnal cycle exists in the Halley electric field measurements (with a mean value of 50V/m and showing a 40% peak to peak variation in comparison to the 34% variation in the Carnegie data). Since the Carnegie Curve represents the variation in thunderstorm activity across the Earth, its presence in the Halley data confirms the presence of the global atmospheric electric circuit signal at Halley. The work presented here will discuss the details of the Halley electric field dataset, including the variability in the fair weather measurements, with a particular focus on magnetic field fluctuations.

  12. Waste Measurement Techniques For Lean Companies

    Directory of Open Access Journals (Sweden)

    Maciej Pieńkowski

    2014-12-01

    Full Text Available The paper is dedicated to answer the problem of measuring waste in companies, which are implementing Lean Manufacturing concept. Lack of complex identification, quantification an visualization of waste significantly impedes Lean transformation efforts. This problem can be solved by a careful investigation of Muda, Muri and Mura, which represent the essence of waste in the Toyota Production System. Measuring them facilitates complete and permanent elimination of waste in processes. The paper introduces a suggestion of methodology, which should enable company to quantify and visualize waste at a shop floor level.

  13. Two Field Techniques for Estimating Relative Abundance of Galliformes

    Institute of Scientific and Technical Information of China (English)

    LuXin; CangjueZhuoma; SuolongCiren; ZhengGuang-mei

    2003-01-01

    Galliformes are often difficult to count adequately in their natural habitats due to low detectability of them. In the present study, we confirm availability of feather-count and feces-count as two useful field techniques to estimate the relative abundance of eared pheasants (Crossoptilon spp. ). The former is suitable to forest environments during the post-incubation period, whereas the latter is best in areas with dry climate conditions during the fall winter season. With the advantages of reduced survey effort and high repeatability, the two techniques are potentially applicable to other Galliform species in habitat selection studies and long-term population monitoring.

  14. Magnetic Linear Birefringence Measurements Using Pulsed Fields

    CERN Document Server

    Berceau, Paul; Battesti, Remy; Rizzo, Carlo

    2011-01-01

    In this paper we present the accomplishment of the further step towards the vacuum magnetic birefringence measurement based on pulsed fields. After describing our BMV experiment, we report the calibration of our apparatus with nitrogen gas and we discuss the precision of our measurement giving a detailed error budget. Our best present vacuum sensitivity is 2.1x 10^-19 T^-2 per 5 ms magnetic pulse. We finally discuss the perspectives to reach our final goal.

  15. Compact Models and Measurement Techniques for High-Speed Interconnects

    CERN Document Server

    Sharma, Rohit

    2012-01-01

    Compact Models and Measurement Techniques for High-Speed Interconnects provides detailed analysis of issues related to high-speed interconnects from the perspective of modeling approaches and measurement techniques. Particular focus is laid on the unified approach (variational method combined with the transverse transmission line technique) to develop efficient compact models for planar interconnects. This book will give a qualitative summary of the various reported modeling techniques and approaches and will help researchers and graduate students with deeper insights into interconnect models in particular and interconnect in general. Time domain and frequency domain measurement techniques and simulation methodology are also explained in this book.

  16. Radar Cross-section Measurement Techniques

    Directory of Open Access Journals (Sweden)

    V.G. Borkar

    2010-03-01

    Full Text Available Radar cross-section (RCS is an important study parameter for defence applications specially dealing with airborne weapon system. The RCS parameter guides the detection range for a target and is therefore studied to understand the effectiveness of a weapon system. It is not only important to understand the RCS characteristics of a target but also to look into the diagnostic mode of study where factors contributing to a particular RCS values are studied. This further opens up subject like RCS suppression and stealth. The paper discusses the RCS principle, control, and need of measurements. Classification of RCS in terms of popular usage is explained with detailed theory of RF imaging and inverse synthetic aperture radar (ISAR. The various types of RCS measurement ranges are explained with brief discussion on outdoor RCS measurement range. The RCS calibration plays a critical role in referencing the measurement to absolute values and has been described.The RCS facility at Reseach Centre Imarat, Hyderabad, is explained with some details of different activities that are carried out including RAM evaluation, scale model testing, and diagnostic imaging.Defence Science Journal, 2010, 60(2, pp.204-212, DOI:http://dx.doi.org/10.14429/dsj.60.341

  17. DIFFRACTO-ASTROMETRY MEASUREMENTS: THE TECHNIQUE

    Directory of Open Access Journals (Sweden)

    L. J. Sánchez

    2014-01-01

    Full Text Available Investigamos la posibilidad de realizar astrometr ́ıa de precisi ́on en im ́agenes estelares saturadas de la Wide Field Planetary Camera 2 (WFPC2 del Hubble Space Telescope (HST. Obtenemos la posici ́on de los fotocentros de ́estas utilizando una t ́ecnica de centrado que usa el patr ́on de difracci ́on producido por el s oporte del espejo secundario. La t ́ecnica parece ser muy prometedora en el an ́alisis astrom ́etrico. Media nte ella logramos una precisi ́on del orden de 10 milisegundos de arco en im ́agenes de la WFPC2.

  18. Techniques for measuring customers’ satisfaction in Banks

    Directory of Open Access Journals (Sweden)

    Elena Lidia MELNIC

    2016-07-01

    Full Text Available The major concern of banks today is to recover and maintain customer trust. Customers need to feel that banks are considering their best interests. Customers are seeking for easy and personalized information. They want to better understand their financial situation and to control it. They want to know both the benefits, as well as the risks. Clients want to work with banks that are concerned about them and about their personal goals. However, only an attractive offer of banks is not the key to success today if is not supported by a superior service culture, that can make notable differentiation in the market. Many banks all over the world are systematically measuring how well they treat customers, identifying the factors shaping satisfaction, and changing operations and marketing as a result. Wise banks measure customer satisfaction regularly because it is one key to customer retention.

  19. PIV MEASUREMENTS FOR GAS FLOW UNDER GRADIENT MAGNETIC FIELDS

    Institute of Scientific and Technical Information of China (English)

    RUAN Xiaodong; WU Feng; F.YAMAMOTO

    2004-01-01

    Particle Image Velocimetry (PIV) techniques were developed to measure the convective N2-air flow under gradient magnetic fields. The velocity fields were calculated by the Minimum Quadratic Difference (MQD) algorithm and spurious vectors were eliminated by Delaunay Tessellation.The N2-air flow was measured as the magnetic flux density varying from 0 ~ 1.5 T. A strengthened vortex flow of air was observed under the condition that the magnetic field was applied, and the velocity of N2 jet rose with the increase of the magnetic density. The experimental results show that the magnetic force will induce a vortex flow and cause a convection flow of the air mixture when both gradients of the O2 concentration and the magnetic field intensity exist.

  20. Techniques for measuring renal transit time

    Energy Technology Data Exchange (ETDEWEB)

    Russell, C.D. [Div. of Nuclear Medicine, Univ. of Alabama at Birmingham Medical Center, AL (United States)]|[Nuclear Medicine Service, V.A. Medical Center, Birmingham, AL (United States); Japanwalla, M. [Div. of Nuclear Medicine, Univ. of Alabama at Birmingham Medical Center, AL (United States)]|[Nuclear Medicine Service, V.A. Medical Center, Birmingham, AL (United States); Khan, S. [Div. of Nuclear Medicine, Univ. of Alabama at Birmingham Medical Center, AL (United States)]|[Nuclear Medicine Service, V.A. Medical Center, Birmingham, AL (United States); Scott, J.W. [Div. of Nuclear Medicine, Univ. of Alabama at Birmingham Medical Center, AL (United States)]|[Nuclear Medicine Service, V.A. Medical Center, Birmingham, AL (United States); Dubovsky, E.V. [Div. of Nuclear Medicine, Univ. of Alabama at Birmingham Medical Center, AL (United States)]|[Nuclear Medicine Service, V.A. Medical Center, Birmingham, AL (United States)

    1995-12-01

    A variety of techniques have been used for quantitative estimation of renal transit time. We compared different indices of transit time in a group of 30 patients having baseline and ACE inhibitor technetium-99m mercaptoacetyltriglycine (MAG{sub 3}) renography prior to arteriography: Peak time, mean transit time, and the ratio of background-subtracted counts at 20 min to those at 3 min. Each index was calculated from whole-kidney ROI, cortical ROI, and cortical factor (by factor analysis). The strongest correlations between angiographic percent of stenosis and transit time index were observed for the peak time (Spearman {rho}=0.469, n=53) and for the R20/3 (again {rho}=0.469, n=53) using the whole-kidney ROI and using only the baseline data without captopril. (Spearman`s {rho} is simply the correlation coefficient calculated from rank in list, which allows for nonlinear correlation.) Thus simple indices of transit time (whole-kidney peak time and R20/3) correlated as well with the observed pathology as did more complicated methods that required deconvolution, factor analysis, or selection of a cortical ROI. (orig./MG)

  1. POF strain sensor using phase measurement techniques

    Science.gov (United States)

    Poisel, H.

    2008-03-01

    Polymer optical fiber (POF) elongation sensors have been proposed e.g. by Doering as a low-cost alternative to FBG (single mode Fiber Bragg Gratings) sensors targeting the lower sensitivity range. A recently recovered detection system known from laser distance meters turned out to be very sensitive while staying simple and thus offering low cost potential. The approach is based on measuring the phase shift of a (e.g. sinusoidally) modulated light signal guided in a POF under different tensions resulting in different transit times and thus different phase shifts.

  2. Atmospheric flow measurements using the PIV and HWA techniques

    Directory of Open Access Journals (Sweden)

    Luciana Bassi Marinho Pires

    2010-08-01

    Full Text Available Alcântara Space Center (ASC is the Brazilian gate to the space where rockets of different sizes are launched. At ASC there is a relative topographical variation, coastal cliff, which modifies the atmospheric boundary layer characteristics and can cause interference for operations of rockets. In the present work, a simplified model (mock-up was studied in a wind tunnel. A scale factor of 1:1000 was used and the atmospheric flow was measured using the hot wire anemometer (HWA and particle image velocimetry (PIV techniques. Using of HWA it was possible to calculate values of average wind speed and fluctuations in a set of points of the section of tests that representing the region of the ASC. Through these measures, other meteorological parameters that represent the atmospheric flow, such as the friction velocity (u*, the roughness length (z0 from the logarithmic profile and the alpha exponent (ɑ of the power law were calculated. With the use of the PIV´s technique, the streamlines and the vorticity fields were obtained and it was noticed that the vorticity generated downwind of the coastal cliff has a strong turbulence (vorticities around 2000 sˉ¹. A rectangular building (simulating the mobile integration tower was inserted at the mock-up and the downwind turbulence was similar to the one generated by the coastal cliff.

  3. Remote measurement of corrosion using ultrasonic techniques

    Energy Technology Data Exchange (ETDEWEB)

    Garcia, K.M.; Porter, A.M.

    1995-02-01

    Supercritical water oxidation (SCWO) technology has the potential of meeting the US Department of Energy`s treatment requirements for mixed radioactive waste. A major technical constraint of the SCWO process is corrosion. Safe operation of a pilot plant requires monitoring of the corrosion rate of the materials of construction. A method is needed for measurement of the corrosion rate taking place during operation. One approach is to directly measure the change in wall thickness or growth of oxide layer at critical points in the SCWO process. In FY-93, a brief survey of the industry was performed to evaluate nondestructive evaluation (NDE) methods for remote corrosion monitoring in supercritical vessels. As a result of this survey, it was determined that ultrasonic testing (UT) methods would be the most cost-effective and suitable method of achieving this. Therefore, the objective for FY-94 was to prove the feasibility of using UT to monitor corrosion of supercritical vessels remotely during operation without removal of the insulation.

  4. Tear film measurement by optical reflectometry technique.

    Science.gov (United States)

    Lu, Hui; Wang, Michael R; Wang, Jianhua; Shen, Meixiao

    2014-02-01

    Evaluation of tear film is performed by an optical reflectometer system with alignment guided by a galvanometer scanner. The reflectometer system utilizes optical fibers to deliver illumination light to the tear film and collect the film reflectance as a function of wavelength. Film thickness is determined by best fitting the reflectance-wavelength curve. The spectral reflectance acquisition time is 15 ms, fast enough for detecting film thickness changes. Fast beam alignment of 1 s is achieved by the galvanometer scanner. The reflectometer was first used to evaluate artificial tear film on a model eye with and without a contact lens. The film thickness and thinning rate have been successfully quantified with the minimum measured thickness of about 0.3 μm. Tear films in human eyes, with and without a contact lens, have also been evaluated. A high-contrast spectral reflectance signal from the precontact lens tear film is clearly observed, and the thinning dynamics have been easily recorded from 3.69 to 1.31 μm with lipid layer thickness variation in the range of 41 to 67 nm. The accuracy of the measurement is better than ±0.58% of the film thickness at an estimated tear film refractive index error of ±0.001. The fiber-based reflectometer system is compact and easy to handle.

  5. Magnetopause Reconnection Impact Parameters from Multiple Spacecraft Magnetic Field Measurements

    Science.gov (United States)

    Wendel, Deirdre E.; Reiff, Patricia H.

    2009-01-01

    We present a novel technique that exploits multiple spacecraft data to determine the impact parameters of the most general form of magnetic reconnection at the magnetopause. The method consists of a superposed epoch of multiple spacecraft magnetometer measurements that yields the instantaneous magnetic spatial gradients near a magnetopause reconnection site. The gradients establish the instantaneous positions of the spacecraft relative to the reconnection site. The analysis is well suited to evaluating the spatial scales of singular field line reconnection, which is characterized by a two-dimensional x-type topology adjacent and perpendicular to a reconnecting singular field line. Application of the method to Cluster data known to lie in the vicinity of a northward IMF reconnection site establishes a field topology consistent with singular field line reconnection and a normal magnetic field component of 20 nT. The corresponding current structure consists of a 130 km sheet possibly embedding a thinner. bifurcated sheet.

  6. Remote optical sensor system for E-field measurements

    Science.gov (United States)

    Heinzelmann, Robert; Stoehr, Andreas; Alder, Thomas; Kalinowski, D.; Schmidt, Manuel; Gross, Matthias; Jaeger, Dieter

    1998-12-01

    The concept of a remote optical sensor system for frequency selective electric field measurements will be presented. The system will be applicable to field measurement problems up to frequencies in the microwave regime. Additionally, it will provide minimum interference with the measured field, due to the optical fiber coupled sensor head. The electrooptic key components within the head of this sensor system are an array of photovoltaic cells and an electroabsorption waveguide modulator. Based on experimental results these components will be discussed and evaluated for the application within the sensor system. Furthermore, a novel fiber modulator coupling technique employing the monolithic integration of the device with InP V-grooves will be presented.

  7. Measurements of 222Rn, 220Rn, and CO2 Emissions in Natural CO2 Fields in Wyoming: MVA Techniques for Determining Gas Transport and Caprock Integrity

    Energy Technology Data Exchange (ETDEWEB)

    Kaszuba, John [Univ. of Wyoming, Laramie, WY (United States); Sims, Kenneth [Univ. of Wyoming, Laramie, WY (United States)

    2014-09-30

    An integrated field-laboratory program evaluated the use of radon and CO2 flux measurements to constrain source and timescale of CO2 fluxes in environments proximate to CO2 storage reservoirs. By understanding the type and depth of the gas source, the integrity of a CO2 storage reservoir can be assessed and monitored. The concept is based on correlations of radon and CO2 fluxes observed in volcanic systems. This fundamental research is designed to advance the science of Monitoring, Verification, and Accounting (MVA) and to address the Carbon Storage Program goal of developing and validating technologies to ensure 99 percent storage performance. Graduate and undergraduate students conducted the research under the guidance of the Principal Investigators; in doing so they were provided with training opportunities in skills required for implementing and deploying CCS technologies. Although a final method or “tool” was not developed, significant progress was made. The field program identified issues with measuring radon in environments rich in CO2. Laboratory experiments determined a correction factor to apply to radon measurements made in CO2-bearing environments. The field program also identified issues with radon and CO2-flux measurements in soil gases at a natural CO2 analog. A systematic survey of radon and CO2 flux in soil gases at the LaBarge CO2 Field in Southwest Wyoming indicates that measurements of 222Rn (radon), 220Rn (thoron), and CO2 flux may not be a robust method for monitoring the integrity of a CO2 storage reservoir. The field program was also not able to correlate radon and CO2 flux in the CO2-charged springs of the Thermopolis hydrothermal system. However, this part of the program helped to motivate the aforementioned laboratory experiments that determined

  8. Evaluation of Contralateral Breast Surface Dose in FIF (Field In Field) Tangential Irradiation Technique for Patients Undergone Breast Conservative Surgery

    Energy Technology Data Exchange (ETDEWEB)

    Park, Byung Moon; Bang, Dong Wan; Bae, Yong Ki; Lee, Jeong Woo [Dept. of Radiation Oncology, Konkuk University Medical Center, Seoul (Korea, Republic of); Kim, You Hyun [Dept. of Radiological Science, College of Health Science, Korea University, Seoul (Korea, Republic of)

    2008-12-15

    The aim of this study is to evaluate contra-lateral breast (CLB) surface dose in Field-in-Field (FIF) technique for breast conserving surgery patients. For evaluation of surface dose in FIF technique, we have compared with other techniques, which were open fields (Open), metal wedge (MW), and enhanced dynamic wedge (EDW) techniques under same geometrical condition and prescribed dose. The three dimensional treatment planning system was used for dose optimization. For the verification of dose calculation, measurements using MOSFET detectors with Anderson Rando phantom were performed. The measured points for four different techniques were at the depth of 0 cm (epidermis) and 0.5 cm bolus (dermis), and spacing toward 2 cm, 4 cm, 6 cm, 8 cm, 10 cm apart from the edge of tangential medial beam. The dose calculations were done in 0.25 cm grid resolution by modified Batho method for inhomogeneity correction. In the planning results, the surface doses were differentiated in the range of 19.6-36.9, 33.2-138.2 for MW, 1.0-7.9, 1.6-37.4 for EDW, and for FIF at the depth of epidermis and dermis as compared to Open respectively. In the measurements, the surface doses were differentiated in the range of 11.1-71, 22.9-161 for MW, 4.1-15.5, 8.2-37.9 for EDW, and 4.9% for FIF at the depth of epidermis and dermis as compared to Open respectively. The surface doses were considered as underestimating in the planning calculation as compared to the measurement with MOSFET detectors. Was concluded as the lowest one among the techniques, even if it was compared with Open method. Our conclusion could be stated that the FIF technique could make the optimum dose distribution in Breast target, while effectively reduce the probability of secondary carcinogenesis due to undesirable scattered radiation to contra-lateral breast.

  9. Recent advances in automation, robotics and measuring techniques

    CERN Document Server

    Zieliński, Cezary; Kaliczyńska, Małgorzata

    2014-01-01

    This book presents the recent advances and developments in control, automation, robotics, and measuring techniques. It presents contributions of top experts in the fields, focused on both theory and industrial practice. The particular chapters present a deep analysis of a specific technical problem which is in general followed by a numerical analysis and simulation, and results of an implementation for the solution of a real world problem. The book presents the results of the International Conference AUTOMATION 2014 held 26 - 28 March, 2014 in Warsaw, Poland on Automation – Innovations and Future Prospectives The presented theoretical results, practical solutions and guidelines will be useful for both researchers working in the area of engineering sciences and for practitioners solving industrial problems.

  10. MEASUREMENTS OF STELLAR MAGNETIC FIELDS USING AUTOCORRELATION OF SPECTRA

    Energy Technology Data Exchange (ETDEWEB)

    Borra, E. F.; Deschatelets, D. [Département de physique, de génie physique et d’optique. Université Laval (Canada)

    2015-11-15

    We present a novel technique that uses the autocorrelation of the spectrum of a star to measure the line broadening caused by the modulus of its average surface magnetic field. The advantage of the autocorrelation comes from the fact that it can detect very small spectral line broadening effects because it averages over many spectral lines and therefore gives an average with a very high signal-to-noise ratio. We validate the technique with the spectra of known magnetic stars and obtain autocorrelation curves that are in full agreement with published magnetic curves obtained with Zeeman splitting. The autocorrelation also gives less noisy curves so that it can be used to obtain very accurate curves. We degrade the resolution of the spectra of these magnetic stars to lower spectral resolutions where the Zeeman splitting is undetectable. At these resolutions, the autocorrelation still gives good quality curves, thereby showing that it can be used to measure magnetic fields in spectra where the Zeeman splitting is significantly smaller than the width of the spectral line. This would therefore allow observing magnetic fields in very faint Ap stars with low-resolution spectrographs, thereby greatly increasing the number of known magnetic stars. It also demonstrates that the autocorrelation can measure magnetic fields in rapidly rotating stars as well as weak magnetic fields that give a Zeeman splitting smaller than the intrinsic width of the spectral lines. Finally, it shows that the autocorrelation can be used to find unknown magnetic stars in low-resolution spectroscopic surveys.

  11. Calculation and measurement of electric field under HVDC transmission lines

    Science.gov (United States)

    Kasdi, A.; Zebboudj, Y.; Yala, H.

    2007-03-01

    A stable corona discharge in a two conductors-to-plane configuration is analysed in this paper. A linear biased probe, without end-effect, has been adapted to a linear geometry and is used for the first time to measure the ground-plane current density and electric field during the bipolar corona. The values of the electric field and the current density are maximum under the two coronating conductors and decrease when moving away from them. Furthermore, a hybrid technique is developed to obtain a general solution of the governing equations of the coupled space-charge and electric field problem. The technique is to use the finite-element method (FEM) to solve Poisson's equation, and the method of characteristic (MOC) to find the charge density from a current-continuity relation. The model avoids resorting to the Deutsch assumption. The computed values are in good agreement with experimental data.

  12. The near field acoustic holography technique for cyclostationary sound field and its experimental research

    Institute of Scientific and Technical Information of China (English)

    WAN Quan; JIANG Weikang

    2005-01-01

    One near field acoustic holography (NAH) technique is proposed for analyzing cyclostationary sound field. The signal of this kind of sound field has very serious modulation phenomenon generally, in spectrum of which obvious sidebands exist. It is difficult for the traditional NAH to possess demodulation function, so virtual power of sidebands exists in its hologram. Replacing the Fourier's transform with the second-order cyclic statistics, the proposed NAH technique uses the cyclic spectrum density (CSD) function as reconstructed physical quantity, instead of the spectrum or power spectrum density of sound pressure signal.The CSD function can demodulate cyclostationary signals, which makes no virtual power of sidebands in its hologram. The results of simulation and experiment show that the proposed NAH can extract more information about cyclostationary sound field than traditional NAH, by which sound field can be known more clearly.

  13. Techniques for transparent lattice measurement and correction

    Science.gov (United States)

    Cheng, Weixing; Li, Yongjun; Ha, Kiman

    2017-07-01

    A novel method has been successfully demonstrated at NSLS-II to characterize the lattice parameters with gated BPM turn-by-turn (TbT) capability. This method can be used at high current operation. Conventional lattice characterization and tuning are carried out at low current in dedicated machine studies which include beam-based measurement/correction of orbit, tune, dispersion, beta-beat, phase advance, coupling etc. At the NSLS-II storage ring, we observed lattice drifting during beam accumulation in user operation. Coupling and lifetime change while insertion device (ID) gaps are moved. With the new method, dynamical lattice correction is possible to achieve reliable and productive operations. A bunch-by-bunch feedback system excites a small fraction (∼1%) of bunches and gated BPMs are aligned to see those bunch motions. The gated TbT position data are used to characterize the lattice hence correction can be applied. As there are ∼1% of total charges disturbed for a short period of time (several ms), this method is transparent to general user operation. We demonstrated the effectiveness of these tools during high current user operation.

  14. Acoustic measuring techniques for suspended sediment

    Science.gov (United States)

    Gruber, P.; Felix, D.; Storti, G.; Lattuada, M.; Fleckenstein, P.; Deschwanden, F.

    2016-11-01

    Acoustic signals can be used in various ways for suspended sediment monitoring. One possibility which lends itself particularly well in the context of hydropower plants (HPPs), is to use installations for acoustic discharge measurement (ADM). Such installations already exist at waterways of many HPPs. Similar to certain turbidimeters, the attenuation of the forward scattered signal travelling through the water-sediment mixture is correlated with suspended sediment concentration (SSC). This correlation can be based on reference SSCs, e.g. from gravimetric analyses of bottle samples. Without the need of additional sensors and practically maintenance-free, this method is used successfully in the HPP Fieschertal to warn the HPP operator of high SSC to prevent excessive turbine abrasion. Acoustic methods and systems that allow for estimating both SSC and particle size distribution (PSD) are under development. The simultaneous determination of SSC and PSD is not possible using a single frequency. Therefore, multi-frequency approaches are investigated for generally scattered signals. When backscattered signals are used, a stronger frequency dependency can be exploited. However, the reliable simultaneous determination of particle size (and distribution) and concentration is still a major challenge due to a low signal-to-noise ratio and an ill- posed problem of estimating concentration and size from recorded signals. The optimal setup configuration (angles, frequencies) for such a system is not unique and further investigations are recommended.

  15. Comparing techniques for measuring corticosterone in tadpoles

    Institute of Scientific and Technical Information of China (English)

    Pablo BURRACO; Rosa ARRIBAS; Saurabh S KULKARNI; Daniel R BUCHHOLZ; Ivan GOMEZ-MESTRE

    2015-01-01

    Glucocorticoids play a key role in mediating stress responses in vertebrates. Corticosterone (CORT) is the main glu-cocorticoid produced in amphibians, birds, and reptiles, and regulates several metabolic functions. The most common methods for quantifying CORT are competitive binding immunoassays: radioimmunoassay (RIA) and enzyme immunoassay (EIA). RIA has been broadly used since the 1980’s but it requires radioactivity. Commercial EIA kits permit quantifying hormone levels without radioactivity although the requirement for a larger sample volume may be a strong limitation for measurements involving larval amphibians. Here we usedXenopus laevis tadpoles to compare the performance of three commonly used procedures for determination of CORT: RIA on a chloroform extract of whole-body homogenate, EIA on plasma, and EIA on supernatant of whole-body homogenate. We treated tadpoles with exogenous CORT at 0, 25, 50, and 100 nM. RIA could distinguish between 0 and 25 nM, and EIA on plasma between 0 and 50 nM, whereas whole-body homogenate EIA only detected significant differences between 0 and 100 nM. Each procedure presents advantages and disadvantages regarding sensitivity, the use of radioactivity, sample size, handling time, and economic cost. RIA is preferred when studying small-bodied animals from which blood samples cannot be obtained. When CORT level differences are intermediate and blood sampling is possible, EIA on plasma is a good non-radioactive alternative. EIA on whole-body homogenates may be useful to assess qualitative changes in CORT levels when considerable differences are expected. Finally, we discuss our findings in the context of previous studies on CORT in amphibians [Current Zoology 61 (5): 835–845, 2015].

  16. Key techniques of the high precision gravity field system

    Science.gov (United States)

    Xu, Weimin; Chen, Shi; Lu, Hongyan; Shi, Lei

    2017-04-01

    Ground-based gravity time series provide a direct method to monitor all sources of mass changes from local to global scale. But the effectively infinite spatial sensitivity of gravity measurements make it difficult to isolate the signal of interest. The high precision gravity field system is an alternative approach of modeling mass changes under-ground. The field system, consists of absolute gravity, gravity and gravity gradient, GNSS, leveling and climate hydrology measurements, can improve the signal-to-noise ratio for many applications by removing contributions of unwanted signal from elevation changes, air pressure changes, local hydrology, and others. The networks of field system combination, such as field-profile in more than 100 kilometers, can be used in critical zone with high seismic risk for monitoring earth dynamics, volcanic and seismic phenomena. The system is constituted by 9 typical observation stations in 3*3 array (or 4 in 2*2 array) in 60 square meters field, each station is designed for integrated measurements, including absolute gravity, gravity gradient, elevation changes, air pressure and hydrology. Time-lapse gravity changes resulting from absolute gravimeter (FG5 or A10) with standard deviation less than 2 μGal, without the contributions of Earth tides, loading and polar motion. Additional measurements such as air pressure change, local hydrology and soil moisture are indispensable. The elevation changes resulting from GNSS (on the base station) and leveling (between stations) with precision less than 10 mm. The gravity gradient is the significant measurement for delimiting the location of the related mass changes underground the station, which is measured by Scintrex CG-5 gravimeters in different height (80cm in the test field), with precision less than 10 E. It is necessary to improve the precision of gravity gradient measurements by certain method in field experiment for the high precision measurement system. Acknowledgment: This

  17. Measuring Propagation Speed of Coulomb Fields

    CERN Document Server

    Calcaterra, A; Finocchiaro, G; Patteri, P; Piccolo, M; Pizzella, G

    2012-01-01

    The problem of gravity propagation has been subject of discussion for quite a long time: Newton, Laplace and, in relatively more modern times, Eddington pointed out that, if gravity propagated with finite velocity, planets motion around the sun would become unstable due to a torque originating from time lag of the gravitational interactions. Such an odd behavior can be found also in electromagnetism, when one computes the propagation of the electric fields generated by a set of uniformly moving charges. As a matter of fact the Li\\'enard-Weichert retarded potential leads to a formula indistinguishable from the one obtained assuming that the electric field propagates with infinite velocity. Feyman explanation for this apparent paradox was based on the fact that uniform motions last indefinitely. To verify such an explanation, we performed an experiment to measure the time/space evolution of the electric field generated by an uniformely moving electron beam. The results we obtain on such a finite lifetime kinema...

  18. The Sine Method: An Alternative Height Measurement Technique

    Science.gov (United States)

    Don C. Bragg; Lee E. Frelich; Robert T. Leverett; Will Blozan; Dale J. Luthringer

    2011-01-01

    Height is one of the most important dimensions of trees, but few observers are fully aware of the consequences of the misapplication of conventional height measurement techniques. A new approach, the sine method, can improve height measurement by being less sensitive to the requirements of conventional techniques (similar triangles and the tangent method). We studied...

  19. Particle fluence measurements by activation technique for radiation damage studies

    CERN Document Server

    León-Florián, E; Furetta, C; Leroy, Claude

    1995-01-01

    High-level radiation environment can produce radiation damage in detectors and their associate electronic components. The establishment of a correlation between damage, irradiation level and absorbed dose requires a precise measurement of the fluence of particles causing the damage. The activation technique is frequently used for performing particle fluence measurements. A review of this technique is presented.

  20. An EIRP Measurement Method for Base-Station Antennas Using Field Strengths Measured along a Single Straight Line

    OpenAIRE

    Soon-Soo Oh; Young-Hwan Lee

    2013-01-01

    We describe an EIRP measurement technique for a base-station antenna. The proposed method especially can be applied to the base-station antenna installed in real environments. Fresnel region measurement method is an optimal technique to avoid the far-field multipath interference, and, furthermore, it could shorten the measurement time. For detecting only the field strengths along a single straight line, we also propose a simple phase-retrieval method. For verification, a simulation and experi...

  1. Measurement of the ATLAS solenoid magnetic field

    CERN Document Server

    Aleksa, M; Giudici, P-A; Kehrli, A; Losasso, M; Pons, X; Sandaker, H; Miyagawa, P S; Snow, S W; Hart, J C; Chevalier, L

    2008-01-01

    ATLAS is a general purpose detector designed to explore a wide range of physics at the Large Hadron Collider. At the centre of ATLAS is a tracking detector in a 2 T solenoidal magnetic field. This paper describes the machine built to map the field, the data analysis methods, the final results, and their estimated uncertainties. The remotely controlled mapping machine used pneumatic motors with feedback from optical encoders to scan an array of Hall probes over the field volume and log data at more than 20 000 points in a few hours. The data were analysed, making full use of the physical constraints on the field and of our knowledge of the solenoid coil geometry. After a series of small corrections derived from the data itself, the resulting maps were fitted with a function obeying Maxwell's equations. The fit residuals had an r.m.s. less than 0.5 mT and the systematic error on the measurement of track sagitta due to the field uncertainty was estimated to be in the range 0.02 % to 0.12 % depending on the track...

  2. A robust technique to reconstruct sound field for all wave-numbers

    Institute of Scientific and Technical Information of China (English)

    YU Fei; CHEN Jian; LI Weibing; CHEN Xinzhao

    2004-01-01

    A robust technique has been proposed for reconstructing sound field for all wave-numbers, which is suitable for the radiation analysis on an arbitrarily-shaped body.According to the wave superposition formulation, the spatial sound field of an actual radiator can be represented equivalently by superposing the fields generated by some fictitious sources interior to the actual radiator. Meanwhile, the strength density on the fictitious sources can be obtained by matching the sound pressures of a finite number of field points. Once the strength density is calculated, the acoustic information at any field point can be obtained subsequently. Finally, some typical numerical examples are given to validate the theoretical analysis, and some investigations are made to analyze the influence of sound frequency and the fictitious source position on the reconstruction precision, which are helpful to the application of the proposed technique to real industrial measurements.

  3. An appraisal of techniques and equipment for cutting force measurement

    Institute of Scientific and Technical Information of China (English)

    AUDY J.

    2006-01-01

    Current research focussed on the assessment of metal machining process parameters and on the development of adaptive control, shows that machine performance, work-piece and tool material selections, tool life, quality of machined surfaces,the geometry of cutting tool edges, and cutting conditions are closely related to the cutting forces. This information is of great interest to cutting tool manufactures and users alike. Over the years there have been significant developments and improvements in the equipment used to monitor such forces. In 1930 mechanical gauges were replaced by resistance strain gauges, and some 30 years later compact air gauge dynamometers were invented. Since this time intensive research has continued being directed towards developing new approaches to cutting force measurement. The Kistler Company, well-known manufacturer of acceleration and piezoelectrical dynamometers, has worked in this field for more than three decades, and developed very sensitive devices.While leading manufacturing research laboratories are often equipped with this technology, classical electrical strain gauges and other dynamometers of individual designs are still commonly used in industry. The present paper presents data obtained using different techniques of force measurement in metal machining processes. In particular, areas of uncertainties, illustrated through results concerning the turning process, are analysed, leading to an appraisal of the current status of these measurements and their significance.

  4. A Diagnostic for Electric Field Measurements in the Near/Far-Field Regions of ICRF Antenna

    Science.gov (United States)

    Martin, E. H.; Caughman, J. B. O.; Isler, R. C.

    2015-11-01

    The physics mechanisms of wave heating and current drive processes in the bulk hot plasma are generally well identified. However, details of the wave-plasma interaction with a material surface in the cold plasma edge are still not fully understood. The driver behind this interaction is the time-periodic wave electric field and is referred to as the near/far-field depending on the location with respect to the antenna. Various models have been formulated to capture the near/far-field physics but have not been tested experimentally. Thus, a diagnostic capable of measuring the electric field with temporal and 3D-spatial resolution is critical for confidence in the codes used to design next generation ICRF antennas. This research is focused on the development of a laser based spectroscopic technique, Doppler-free saturation spectroscopy (DFSS), and its implementation to study near/far-field physics. Using DFSS the spectra line profile of various electronic transitions are measured and fit to a quantum mechanical model incorporating both magnetic and dynamic electric field operators. The electric field direction and magnitude are extracted from the fit. The experimental setup and planned experiments will be discussed. Additionally, initial measurements of fitted Hδ spectrum under the influence of known electric and magnetic fields will be presented.

  5. MPPT Technique Based on Current and Temperature Measurements

    Directory of Open Access Journals (Sweden)

    Eduardo Moreira Vicente

    2015-01-01

    Full Text Available This paper presents a new maximum power point tracking (MPPT method based on the measurement of temperature and short-circuit current, in a simple and efficient approach. These measurements, which can precisely define the maximum power point (MPP, have not been used together in other existing techniques. The temperature is measured with a low cost sensor and the solar irradiance is estimated through the relationship of the measured short-circuit current and its reference. Fast tracking speed and stable steady-state operation are advantages of this technique, which presents higher performance when compared to other well-known techniques.

  6. Field Measurements of Black Carbon Yields from Gas Flaring.

    Science.gov (United States)

    Conrad, Bradley M; Johnson, Matthew R

    2017-02-07

    Black carbon (BC) emissions from gas flaring in the oil and gas industry are postulated to have critical impacts on climate and public health, but actual emission rates remain poorly characterized. This paper presents in situ field measurements of BC emission rates and flare gas volume-specific BC yields for a diverse range of flares. Measurements were performed during a series of field campaigns in Mexico and Ecuador using the sky-LOSA optical measurement technique, in concert with comprehensive Monte Carlo-based uncertainty analyses. Parallel on-site measurements of flare gas flow rate and composition were successfully performed at a subset of locations enabling direct measurements of fuel-specific BC yields from flares under field conditions. Quantified BC emission rates from individual flares spanned more than 4 orders of magnitude (up to 53.7 g/s). In addition, emissions during one notable ∼24-h flaring event (during which the plume transmissivity dropped to zero) would have been even larger than this maximum rate, which was measured as this event was ending. This highlights the likely importance of superemitters to global emission inventories. Flare gas volume-specific BC yields were shown to be strongly correlated with flare gas heating value. A newly derived correlation fitting current field data and previous lab data suggests that, in the context of recent studies investigating transport of flare-generated BC in the Arctic and globally, impacts of flaring in the energy industry may in fact be underestimated.

  7. Opto-thermal in-vivo skin hydration measurements - a comparison study of different measurement techniques

    Energy Technology Data Exchange (ETDEWEB)

    Xiao, P; Singh, H; Imhof, R E [Faculty of ESBE, London South Bank University, 103 Borough Road, London SE1 0AA (United Kingdom); Ciortea, L I; Berg, E P [Biox Systems Ltd, 103 Borough Road, London SE1 0AA (United Kingdom); Cui, Y, E-mail: xiaop@lsbu.ac.u [Sunrise Systems Limited, Flint Bridge Business Centre, Ely Road, Waterbeach, Cambridge CB5 9QZ (United Kingdom)

    2010-03-01

    We compared five different skin hydration measurement techniques, namely OTTER, Fingerprint sensors, Corneometer, Nova, and Moisture Checker, in order to understand the correlations between different skin hydration measurement techniques and to understand the repeatability of each technique. The measurements are performed on different in-vivo skin sites from different volunteers and at different hydration levels. The repeatability of different techniques is achieved by measuring the same skin site repeatedly. The correlations between different skin hydration measurement techniques are achieved by plotting results from different techniques against each other. The different skin hydration levels are achieved through the recovery period after a skin immersive hydration.

  8. Two Field Techniques for Estimating Relative Abundance of Galliformes

    Institute of Scientific and Technical Information of China (English)

    Lu Xin; Cangjue Zhuoma; Suolong Ciren; Zheng Guang-mei

    2003-01-01

    Galliformes are often difficult to count adequate-ly in their natural habitats due to low detectability of them. In the present study, we confirm availability of feather-count and feces-count as two useful field techniques to estimate the rela-tive abundance of eared-pheasants (Crossoptilon spp. ). The former is suitable to forest environments during the post-incu-bation period, whereas the latter is best in areas with dry cli-mate conditions during the fall-winter season. With the ad-vantages of reduced survey effort and high repeatability, the two techniques are potentially applicable to other Galliform species in habitat selection studies and long-term population monitoring.

  9. Wave directional spreading from point field measurements

    Science.gov (United States)

    McAllister, M. L.; Venugopal, V.; Borthwick, A. G. L.

    2017-04-01

    Ocean waves have multidirectional components. Most wave measurements are taken at a single point, and so fail to capture information about the relative directions of the wave components directly. Conventional means of directional estimation require a minimum of three concurrent time series of measurements at different spatial locations in order to derive information on local directional wave spreading. Here, the relationship between wave nonlinearity and directionality is utilized to estimate local spreading without the need for multiple concurrent measurements, following Adcock & Taylor (Adcock & Taylor 2009 Proc. R. Soc. A 465, 3361-3381. (doi:10.1098/rspa.2009.0031)), with the assumption that directional spreading is frequency independent. The method is applied to measurements recorded at the North Alwyn platform in the northern North Sea, and the results compared against estimates of wave spreading by conventional measurement methods and hindcast data. Records containing freak waves were excluded. It is found that the method provides accurate estimates of wave spreading over a range of conditions experienced at North Alwyn, despite the noisy chaotic signals that characterize such ocean wave data. The results provide further confirmation that Adcock and Taylor's method is applicable to metocean data and has considerable future promise as a technique to recover estimates of wave spreading from single point wave measurement devices.

  10. Micro machining techniques commonly used in manufacturing field

    Directory of Open Access Journals (Sweden)

    Adem Çiçek

    2011-06-01

    Full Text Available Developing technology and the need for high-precision parts in manufacturing industry has revealed the micro-machining. Machine tools and work pieces are miniaturized through micro-machining, materials and power consumption reduced to a minimum level. High productiveness in the use of resources and time can be obtained through this rapidly growing industry around the world. In this paper, different micro-machining techniques have been classified revising the investigations recently performed in the field of micro-machining and discussed their contributions to manufacturing process.

  11. Ultrasound field measurement using a binary lens

    CERN Document Server

    Clement, Gregory T; Kamakura, Tomoo

    2014-01-01

    Field characterization methods using a scattering target in the absence of a point-like receiver have been well described in which scattering is recorded by a relatively large receiver located outside the field of measurement. Unfortunately, such methods are prone to artifacts due to averaging across the receiver surface. To avoid this problem while simultaneously increasing the gain of a received signal, the present study introduces a binary plate lens designed to focus spherically-spreading waves onto a planar region having a nearly-uniform phase proportional to that of the target location. The lens is similar to a zone plate, but modified to produce a bi-convex-like behavior, such that it focuses both planar and spherically spreading waves. A measurement device suitable for characterizing narrowband ultrasound signals in air is designed around this lens by coupling it to a target and planar receiver. A prototype device is constructed and used to characterize the field of a highly-focused 400 kHz air transd...

  12. Measuring propagation speed of Coulomb fields

    Energy Technology Data Exchange (ETDEWEB)

    Sangro, R. de; Finocchiaro, G.; Patteri, P.; Piccolo, M.; Pizzella, G. [Istituto Nazionale di Fisica Nucleare, Laboratori Nazionali di Frascati, Frascati (Italy)

    2015-03-01

    The problem of gravity propagation has been subject of discussion for quite a long time: Newton, Laplace and, in relatively more modern times, Eddington pointed out that, if gravity propagated with finite velocity, planet motion around the sun would become unstable due to a torque originating from time lag of the gravitational interactions. Such an odd behavior can be found also in electromagnetism, when one computes the propagation of the electric fields generated by a set of uniformly moving charges. As a matter of fact the Lienard-Weichert retarded potential leads to the same formula as the one obtained assuming that the electric field propagate with infinite velocity. The Feynman explanation for this apparent paradox was based on the fact that uniform motions last indefinitely. To verify such an explanation, we performed an experiment to measure the time/space evolution of the electric field generated by an uniformly moving electron beam. The results we obtain, on a finite lifetime kinematical state, are compatible with an electric field rigidly carried by the beam itself. (orig.)

  13. Soil Water Balance Measurement in Field Scale

    Institute of Scientific and Technical Information of China (English)

    CHENZHI-XIONG

    1992-01-01

    A 5-year experiment on water balance has been conducted in a flat rainfed wheat field with an area of 66×100m2 in Fengqiu,Henan Province in China.Based on the analysis of semi-variance functions conducted with soil moisture samples taken from 77 nodes of a 10×10m2 grid,the soil moisture distribution in the field was structural with a temporal stability.According to the autocorrelation range of the semi-variance function,6 sites were selected for the determination of soil water conditions.The characteristic of probability density function of the differences of water storage in two sets of measurements showed that the distribution of these variables in the field was a normal one.The error in the estimation of the average of 5 random samples was 14% (α=0.10),and the errors of water consumption by wheat during the experiments were estimated to be 6-13%.Sime the experimental field was large enough to avoid any edge effect,the results obtained should tally with the actual situation.Yet the soil system was heterogeneous,so we must follow the principles of statistics and geostatistics when describing the system's status with the average of the samples.

  14. Analysis of rainfall inputs and runoff under an A-frame oscillating rainfall simulator in a sugarcane field, Mackay region of Queensland: Matching measurement techniques to meet project water balance objectives

    Science.gov (United States)

    Fentie, Banti; Yu, Bofu; Ciesiolka, Cyril

    2010-05-01

    A total of 11 rainfall simulations were conducted on four different plots (ranging in area from 22.10 to 26.20 m2) in a sugarcane field (with slopes varying from 1-9% and a groundcover variability of bare - 100% cover) in the Mackay region of Northern Queensland. The objectives of these rainfall simulation experiments were many, but this paper discusses the measurement methodology and data quality of rainfall generated and subsequent runoff. Rainfall amount during the simulations was measured using two different sizes of rain gauges placed at different locations on the plot (left, centre, and right sides of the experimental plot). In addition to the 203mm ordinary rain gauges, three pluviometers (300mm) were placed along the centre of the plot to measure rainfall as a function of time during the simulation. The rainfall data from these three pluviometers was collected using dataloggers and processed using a computer program called Datalog, which converted the number of tips/minute into mm/h. Due to spatial variation of rainfall intensity applied to the surface as a function of height from the nozzles of the rainfall simulators, correction factors were determined using a computer program called ERFS developed for this purpose. The rainfall from each gauge and pluviometer was subsequently corrected for distance from the nozzles of the simulator and height of the gauge by multiplying it by the corresponding correction factor. The spatial distribution of rainfall amount during each simulation was determined by spatially interpolating measured amounts in order to ascertain the best estimate of applied rainfall and its energy. Runoff data during each simulation was collected using tipping buckets connected to data loggers. Runoff amounts were also manually collected at specified intervals as a back up, and for validation of those collected using tipping buckets in determining runoff rates for each simulation. Soil cores were taken for determining soil moisture balances

  15. Large Field Photogrammetry Techniques in Aircraft and Spacecraft Impact Testing

    Science.gov (United States)

    Littell, Justin D.

    2010-01-01

    The Landing and Impact Research Facility (LandIR) at NASA Langley Research Center is a 240 ft. high A-frame structure which is used for full-scale crash testing of aircraft and rotorcraft vehicles. Because the LandIR provides a unique capability to introduce impact velocities in the forward and vertical directions, it is also serving as the facility for landing tests on full-scale and sub-scale Orion spacecraft mass simulators. Recently, a three-dimensional photogrammetry system was acquired to assist with the gathering of vehicle flight data before, throughout and after the impact. This data provides the basis for the post-test analysis and data reduction. Experimental setups for pendulum swing tests on vehicles having both forward and vertical velocities can extend to 50 x 50 x 50 foot cubes, while weather, vehicle geometry, and other constraints make each experimental setup unique to each test. This paper will discuss the specific calibration techniques for large fields of views, camera and lens selection, data processing, as well as best practice techniques learned from using the large field of view photogrammetry on a multitude of crash and landing test scenarios unique to the LandIR.

  16. Direct imaging of neural currents using ultra-low field magnetic resonance techniques

    Science.gov (United States)

    Volegov, Petr L.; Matlashov, Andrei N.; Mosher, John C.; Espy, Michelle A.; Kraus, Jr., Robert H.

    2009-08-11

    Using resonant interactions to directly and tomographically image neural activity in the human brain using magnetic resonance imaging (MRI) techniques at ultra-low field (ULF), the present inventors have established an approach that is sensitive to magnetic field distributions local to the spin population in cortex at the Larmor frequency of the measurement field. Because the Larmor frequency can be readily manipulated (through varying B.sub.m), one can also envision using ULF-DNI to image the frequency distribution of the local fields in cortex. Such information, taken together with simultaneous acquisition of MEG and ULF-NMR signals, enables non-invasive exploration of the correlation between local fields induced by neural activity in cortex and more `distant` measures of brain activity such as MEG and EEG.

  17. Techniques for measuring ammonia in fly ash, mortar, and concrete

    Energy Technology Data Exchange (ETDEWEB)

    Rathbone, R.F. [Kentucky Univ., Lexington, KY (United States). Center for Applied Energy Reseach; Majors, R.K. [Boral Material Technologies, Inc., San Antonio, TX (United States). Engineered Materials

    2003-12-01

    The presence of ammonia in fly ash that is to be used in mortar and concrete is of increasing concern in the U.S., mainly due to the installation of selective catalytic reduction (SCR) DeNOx systems. When the SCR catalyst is new, contamination of the fly ash with ammonia is generally not a concern. However, as the catalyst in the SCR ages and becomes less efficient, the ammonia slip increases and results in a greater amount of ammonium salt being precipitated on the fly ash. The increase in ammonia concentration is compounded by variability that can occur on a day-to-day basis. When marketing ammonia-laden fly ash for use in mortar and concrete it is imperative that the concentration of ammonia is known. However, there currently is no widely accepted or ''standard'' method for ammonia measurement in fly ash. This paper describes two methods that have been developed and used by the University of Kentucky Center for Applied Energy Research and Boral Material Technologies, Inc. One of the methods uses gas detection tubes and can provide an accurate determination within five to ten minutes. Thus it is suitable as a rapid field technique. The other method employs a gas-sensing electrode and requires a longer period of time to complete the measurement. However, this second method can also be used to determine the quantity of ammonia in fresh mortar and concrete. (orig.)

  18. Technique for Measuring Body Circumferences and Skinfold Thicknesses.

    Science.gov (United States)

    1984-08-01

    of the tape measure. Technique For ease and accuracy of measurement, male subjects ( persons being measured) should wear swim suits or shorts and female...are now touching the second costo -sternal joint (Figure 3a). There is usually a slight bulge or prominence on the sternum at this level. This

  19. IMAGE SEGMENTATION BASED ON MARKOV RANDOM FIELD AND WATERSHED TECHNIQUES

    Institute of Scientific and Technical Information of China (English)

    纳瑟; 刘重庆

    2002-01-01

    This paper presented a method that incorporates Markov Random Field(MRF), watershed segmentation and merging techniques for performing image segmentation and edge detection tasks. MRF is used to obtain an initial estimate of x regions in the image under process where in MRF model, gray level x, at pixel location i, in an image X, depends on the gray levels of neighboring pixels. The process needs an initial segmented result. An initial segmentation is got based on K-means clustering technique and the minimum distance, then the region process in modeled by MRF to obtain an image contains different intensity regions. Starting from this we calculate the gradient values of that image and then employ a watershed technique. When using MRF method it obtains an image that has different intensity regions and has all the edge and region information, then it improves the segmentation result by superimpose closed and an accurate boundary of each region using watershed algorithm. After all pixels of the segmented regions have been processed, a map of primitive region with edges is generated. Finally, a merge process based on averaged mean values is employed. The final segmentation and edge detection result is one closed boundary per actual region in the image.

  20. Digital technique for the simultaneous measurement of velocity and temperature.

    Science.gov (United States)

    Keffer, J F; Budny, R S; Kawall, J G

    1978-09-01

    A computer-oriented, hot-wire anemometer technique for the simultaneous measurement of velocity and temperature in heated turbulent flows is described. This technique involves conversion of analogue anemometer voltage signals into digital forms and processing of these latter on a digital computer, in accordance with the anemometer response equations, to obtain instantaneous temperature and velocity. The technique was tested with a heated plane jet and found to be satisfactory.

  1. A Survey of Advanced Microwave Frequency Measurement Techniques

    Directory of Open Access Journals (Sweden)

    Anand Swaroop Khare

    2012-06-01

    Full Text Available Microwaves are radio waves with wavelengths ranging from as long as one meter to as short as one millimeter, or equivalently, with frequencies between 300 MHz and 300 GHz. The science of photonics includes the generation, emission, modulation, signal processing, switching, transmission, amplification, detection and sensing of light. Microwave photonics has been introduced for achieving ultra broadband signal processing. Instantaneous Frequency Measurement (IFM receivers play an important role in electronic warfare. Technologies used for signal processing, include conventional direct Radio Frequency (RF techniques, digital techniques, intermediate frequency (IF techniques and photonic techniques. Direct RF techniques suffer an increased loss, high dispersion, and unwanted radiation problems in high frequencies. The systems that use traditional RF techniques can be bulky and often lack the agility required to perform advanced signal processing in rapidly changing environments. In this paper we discussed a survey of Microwave Frequency Measurement Techniques. The microwaves techniques are categorized based upon different approaches. This paper provides the major advancement in the Microwave Frequency MeasurementTechniques research; using these approaches the features and categories in the surveyed existing work.

  2. A New Technique for Measuring the Heat Loss Coefficient

    DEFF Research Database (Denmark)

    Svendsen, Sv Aa Højgaard; Rose, Jørgen

    1996-01-01

    To measure the effect of linear cold bridges in building envelope constructions the guarded hot box technique is used. A new method based on a guarded hot plate technique has been proposed and investigated with respect to errors. The results are promising and further development of the method is ...

  3. Measurement techniques for radiological characterization of contaminated sites

    Energy Technology Data Exchange (ETDEWEB)

    Loos, M.

    1996-09-18

    Once the decision is taken to characterize a contaminated site, appropriate measurement techniques must be selected. The choice will depend on the available information, on the nature and extent of the contamination, as well as on available resources (staff and budget). Some techniques are described on the basis of examples of characterization projects (e.g. Olen area in Belgium).

  4. Effects of equipment and technique on peak flow measurements

    Directory of Open Access Journals (Sweden)

    O'Driscoll B Ronan

    2006-06-01

    Full Text Available Abstract Background Different lung function equipment and different respiratory manoeuvres may produce different Peak Expiratory Flow (PEF results. Although the PEF is the most common lung function test, there have been few studies of these effects and no previous study has evaluated both factors in a single group of patients. Methods We studied 36 subjects (PEF range 80–570 l/min. All patients recorded PEF measurements using a short rapid expiration following maximal inspiration (PEF technique or a forced maximal expiration to residual volume (FVC technique. Measurements were made using a Wright's peak flow meter, a turbine spirometer and a Fleisch pneumotachograph spirometer. Results The mean PEF was 8.7% higher when the PEF technique was used (compared with FVC technique, p Conclusion Peak flow measurements are affected by the instruction given and by the device and Peak Flow scale used. Patient management decisions should not be based on PEF measurement made on different instruments.

  5. Measuring elastic constants using non-contact ultrasonic techniques

    Science.gov (United States)

    Edwards, R. S.; Perry, R.; Cleanthous, D.; Backhouse, D. J.; Moore, I. J.; Clough, A. R.; Stone, D. I.

    2012-05-01

    The use of ultrasound for measuring elastic constants and phase transitions is well established. Standard measurements use piezoelectric transducers requiring couplant and contact with the sample. Recently, non-destructive testing (NDT) has seen an increase in the use of non-contact ultrasonic techniques, for example electromagnetic acoustic transducers (EMATs) and laser ultrasound, due to their many benefits. For measurements of single crystals over a range of temperatures non-contact techniques could also bring many benefits. These techniques do not require couplant, and hence do not suffer from breaking of the bond between transducer and sample during thermal cycling, and will potentially lead to a simpler and more adaptable measurement system with lower risk of sample damage. We present recent work adapting EMAT advances from NDT to measurements of single crystals at cryogenic temperatures and illustrate this with measurements of magnetic phase transitions in Gd64Sc36 using both contact and non-contact transducers. We discuss the measurement techniques implemented to overcome noise problems, and a digital pulse-echo-overlap technique, using data analysis in the frequency domain to measure the velocity.

  6. Scale-model charge-transfer technique for measuring enhancement factors

    Science.gov (United States)

    Kositsky, J.; Nanevicz, J. E.

    1991-01-01

    Determination of aircraft electric field enhancement factors is crucial when using airborne field mill (ABFM) systems to accurately measure electric fields aloft. SRI used the scale model charge transfer technique to determine enhancement factors of several canonical shapes and a scale model Learjet 36A. The measured values for the canonical shapes agreed with known analytic solutions within about 6 percent. The laboratory determined enhancement factors for the aircraft were compared with those derived from in-flight data gathered by a Learjet 36A outfitted with eight field mills. The values agreed to within experimental error (approx. 15 percent).

  7. LIDAR Wind Speed Measurements of Evolving Wind Fields

    Energy Technology Data Exchange (ETDEWEB)

    Simley, E.; Pao, L. Y.

    2012-07-01

    Light Detection and Ranging (LIDAR) systems are able to measure the speed of incoming wind before it interacts with a wind turbine rotor. These preview wind measurements can be used in feedforward control systems designed to reduce turbine loads. However, the degree to which such preview-based control techniques can reduce loads by reacting to turbulence depends on how accurately the incoming wind field can be measured. Past studies have assumed Taylor's frozen turbulence hypothesis, which implies that turbulence remains unchanged as it advects downwind at the mean wind speed. With Taylor's hypothesis applied, the only source of wind speed measurement error is distortion caused by the LIDAR. This study introduces wind evolution, characterized by the longitudinal coherence of the wind, to LIDAR measurement simulations to create a more realistic measurement model. A simple model of wind evolution is applied to a frozen wind field used in previous studies to investigate the effects of varying the intensity of wind evolution. LIDAR measurements are also evaluated with a large eddy simulation of a stable boundary layer provided by the National Center for Atmospheric Research. Simulation results show the combined effects of LIDAR errors and wind evolution for realistic turbine-mounted LIDAR measurement scenarios.

  8. Full-field optical coherence tomography apply in sphere measurements

    Science.gov (United States)

    Shi, Wei; Li, Weiwei; li, Juncheng; Wang, Jingyu; Wang, Jianguo

    2016-10-01

    The geometry of a spherical surface, for example that of a precision optic, is completely determined by the radius -of-curvature at one point and the deviation from the perfect spherical form at all other points of the sphere. Full-field Optical Coherence Tomography (FF-OCT) is a parallel detection OCT technique that utilizes a 2D detector array. This technique avoids mechanical scanning in imaging optics, thereby speeding up the imaging process and enhancing the quality of images. The current paper presents an FF-OCT instrument that is designed to be used in sphere measurement with the principle of multiple delays (MD) OCT to evaluate the curvature and radius of curved objects in single-shot imaging. The optimum combination of the MD principle with the FF-OCT method was evaluated, and the radius of a metal ball was measured with this method. The generated 2n-1 contour lines were obtained by using an MDE with n delays in a single en-face OCT image. This method of measurement, it engaged in the measurement accuracy of spherical and enriches the means of measurement, to make a spherical scan techniques flexible application.

  9. Error reduction techniques for measuring long synchrotron mirrors

    Energy Technology Data Exchange (ETDEWEB)

    Irick, S.

    1998-07-01

    Many instruments and techniques are used for measuring long mirror surfaces. A Fizeau interferometer may be used to measure mirrors much longer than the interferometer aperture size by using grazing incidence at the mirror surface and analyzing the light reflected from a flat end mirror. Advantages of this technique are data acquisition speed and use of a common instrument. Disadvantages are reduced sampling interval, uncertainty of tangential position, and sagittal/tangential aspect ratio other than unity. Also, deep aspheric surfaces cannot be measured on a Fizeau interferometer without a specially made fringe nulling holographic plate. Other scanning instruments have been developed for measuring height, slope, or curvature profiles of the surface, but lack accuracy for very long scans required for X-ray synchrotron mirrors. The Long Trace Profiler (LTP) was developed specifically for long x-ray mirror measurement, and still outperforms other instruments, especially for aspheres. Thus, this paper focuses on error reduction techniques for the LTP.

  10. Lorentz force electrical impedance tomography using magnetic field measurements.

    Science.gov (United States)

    Zengin, Reyhan; Gençer, Nevzat Güneri

    2016-08-21

    In this study, magnetic field measurement technique is investigated to image the electrical conductivity properties of biological tissues using Lorentz forces. This technique is based on electrical current induction using ultrasound together with an applied static magnetic field. The magnetic field intensity generated due to induced currents is measured using two coil configurations, namely, a rectangular loop coil and a novel xy coil pair. A time-varying voltage is picked-up and recorded while the acoustic wave propagates along its path. The forward problem of this imaging modality is defined as calculation of the pick-up voltages due to a given acoustic excitation and known body properties. Firstly, the feasibility of the proposed technique is investigated analytically. The basic field equations governing the behaviour of time-varying electromagnetic fields are presented. Secondly, the general formulation of the partial differential equations for the scalar and magnetic vector potentials are derived. To investigate the feasibility of this technique, numerical studies are conducted using a finite element method based software. To sense the pick-up voltages a novel coil configuration (xy coil pairs) is proposed. Two-dimensional numerical geometry with a 16-element linear phased array (LPA) ultrasonic transducer (1 MHz) and a conductive body (breast fat) with five tumorous tissues is modeled. The static magnetic field is assumed to be 4 Tesla. To understand the performance of the imaging system, the sensitivity matrix is analyzed. The sensitivity matrix is obtained for two different locations of LPA transducer with eleven steering angles from [Formula: see text] to [Formula: see text] at intervals of [Formula: see text]. The characteristics of the imaging system are shown with the singular value decomposition (SVD) of the sensitivity matrix. The images are reconstructed with the truncated SVD algorithm. The signal-to-noise ratio in measurements is assumed 80 d

  11. Lorentz force electrical impedance tomography using magnetic field measurements

    Science.gov (United States)

    Zengin, Reyhan; Güneri Gençer, Nevzat

    2016-08-01

    In this study, magnetic field measurement technique is investigated to image the electrical conductivity properties of biological tissues using Lorentz forces. This technique is based on electrical current induction using ultrasound together with an applied static magnetic field. The magnetic field intensity generated due to induced currents is measured using two coil configurations, namely, a rectangular loop coil and a novel xy coil pair. A time-varying voltage is picked-up and recorded while the acoustic wave propagates along its path. The forward problem of this imaging modality is defined as calculation of the pick-up voltages due to a given acoustic excitation and known body properties. Firstly, the feasibility of the proposed technique is investigated analytically. The basic field equations governing the behaviour of time-varying electromagnetic fields are presented. Secondly, the general formulation of the partial differential equations for the scalar and magnetic vector potentials are derived. To investigate the feasibility of this technique, numerical studies are conducted using a finite element method based software. To sense the pick-up voltages a novel coil configuration (xy coil pairs) is proposed. Two-dimensional numerical geometry with a 16-element linear phased array (LPA) ultrasonic transducer (1 MHz) and a conductive body (breast fat) with five tumorous tissues is modeled. The static magnetic field is assumed to be 4 Tesla. To understand the performance of the imaging system, the sensitivity matrix is analyzed. The sensitivity matrix is obtained for two different locations of LPA transducer with eleven steering angles from -{{25}\\circ} to {{25}\\circ} at intervals of {{5}\\circ} . The characteristics of the imaging system are shown with the singular value decomposition (SVD) of the sensitivity matrix. The images are reconstructed with the truncated SVD algorithm. The signal-to-noise ratio in measurements is assumed 80 dB. Simulation studies

  12. A review of hemorheology: Measuring techniques and recent advances

    Science.gov (United States)

    Sousa, Patrícia C.; Pinho, Fernando T.; Alves, Manuel A.; Oliveira, Mónica S. N.

    2016-02-01

    Significant progress has been made over the years on the topic of hemorheology, not only in terms of the development of more accurate and sophisticated techniques, but also in terms of understanding the phenomena associated with blood components, their interactions and impact upon blood properties. The rheological properties of blood are strongly dependent on the interactions and mechanical properties of red blood cells, and a variation of these properties can bring further insight into the human health state and can be an important parameter in clinical diagnosis. In this article, we provide both a reference for hemorheological research and a resource regarding the fundamental concepts in hemorheology. This review is aimed at those starting in the field of hemodynamics, where blood rheology plays a significant role, but also at those in search of the most up-to-date findings (both qualitative and quantitative) in hemorheological measurements and novel techniques used in this context, including technical advances under more extreme conditions such as in large amplitude oscillatory shear flow or under extensional flow, which impose large deformations comparable to those found in the microcirculatory system and in diseased vessels. Given the impressive rate of increase in the available knowledge on blood flow, this review is also intended to identify areas where current knowledge is still incomplete, and which have the potential for new, exciting and useful research. We also discuss the most important parameters that can lead to an alteration of blood rheology, and which as a consequence can have a significant impact on the normal physiological behavior of blood.

  13. An ultrasonic technique for measuring stress in fasteners

    Science.gov (United States)

    Stevens, K. J.; Day, P.; Byron, D.

    1999-12-01

    High temperature bolting alloys are extensively used in the thermal power generation industry as for example, reheat ESV and Governor valve studs. Remnant life assessment methodologies and plant maintenance procedures require the monitoring of the operational stress levels in these fasteners. Some conventional ultrasonic techniques require longitudinal wave measurements to be undertaken when the nut on the bolt is loosened and then re-tightened. Other techniques use a combination of shear waves and longitudinal waves. In this paper, the problems and pitfalls associated with various ultrasonic techniques for measuring stress in bolts, is discussed. An ultrasonic technique developed for measuring the stress in Durehete 1055 bolts is presented. Material from a textured rolled bar has been used as a test bed in the development work. The technique uses shear wave birefringence and compression waves at several frequencies to measure texture, fastener length and the average stress. The technique was developed by making ultrasonic measurements on bolts tensioned in universal testing machines and a hydraulic nut. The ultrasonic measurements of residual stress have been checked against strain gauge measurements. The Durehete bolts have a hollow cylinder geometry of restricted dimensions, which significantly alters compression and shear wave velocities from bulk values and introduces hoop stresses which can be measured by rotating the polarization of the shear wave probe. Modelling of the experimental results has been undertaken using theories for the elastic wave propagation through waveguides. The dispersion equations allow the velocity and length of the fastener to be measured ultrasonically in some situations where the length of the fastener can not be measured directly with a vernier caliper or micrometer and/or where it is undesirable to loosen nuts to take calibration readings of the shear and compression wave velocities.

  14. GHz measurements of correlated electron systems in high magnetic fields

    CERN Document Server

    Edwards, R S

    2002-01-01

    This Thesis presents experiments performed on the high-frequency conductivity of materials in high magnetic fields. The angle dependence of resonances measured in the millimetre-wave absorption is studied using a rotating resonant cavity system, and the frequency dependence is measured using transmission techniques and a tuneable resonant cavity. Chapter 1 introduces the materials. These include the crystalline organic metals, the layered superconductor Sr sub 2 RUO sub 4 and the quantum Ising ferromagnet LiHoF sub 4. In Chapters 2 and 3, the necessary physics and experimental techniques for their investigation are outlined. Chapters 4 to 6 present measurements of cyclotron resonance in layered materials. Chapter 4 describes several models for the origin of cyclotron resonance harmonics, and describes the first definite measurement of the harmonics of a cyclotron resonance in an organic molecular metal, namely beta sup - (BEDT-TTF) sub 2 SF sub 5 CH sub 2 CF sub 2 SO sub 3. The angle dependence of the field p...

  15. Total Field and Scattered Field Technique for Fourth-Order Symplectic Finite Difference Time Domain Method

    Institute of Scientific and Technical Information of China (English)

    SHA Wei; HUANG Zhi-Xiang; WU Xian-Liang; CHEN Ming-Sheng

    2006-01-01

    Using symplectic integrator propagator, a three-dimensional fourth-order symplectic finite difference time domain (SFDTD) method is studied, which is of the fourth order in both the time and space domains. The method is nondissipative and can save more memory compared with the traditional FDTD method. The total field and scattered field (TF-SF) technique is derived for the SFDTD method to provide the incident wave source conditions. The bistatic radar cross section (RCS) of a dielectric sphere is computed by using the SFDTD method for the first time. Numerical results suggest that the SFDTD algorithm acquires better stability and accuracy compared with the traditional FDTD method.

  16. Modified methods of stellar magnetic field measurements

    CERN Document Server

    Kholtygin, A F

    2013-01-01

    The standard methods of the magnetic field measurement, based on an analysis of the relation between the Stokes $V$-parameter and the first derivative of the total line profile intensity, were modified by applying a linear integral operator $\\hat{L}$ to the both sides of this relation. As the operator $\\hat{L}$, the operator of the wavelet transform with DOG-wavelets is used. The key advantage of the proposed method is an effective suppression of the noise contribution to the line profile and the Stokes parameter $V$. The efficiency of the method has been studied using the model line profiles with various noise contributions. To test the proposed method, the spectropolarimetric observations of the A0-type star $\\alpha^2\\,$ CVn, young O-type star $\\theta^1$ Ori C and A0 supergiant HD 92207 were used. The longitudinal magnetic field strengths for these stars calculated by our method appeared to be in a good agreement with those determined by other methods.

  17. Blower-door techniques for measuring interzonal leakage

    Energy Technology Data Exchange (ETDEWEB)

    Hult, Erin L.; Sherman, Max H.; Walker, Iain

    2013-01-01

    Abstract The standard blower door test methods, such as ASTM E779, describe how to use a single blower door to determine the total leakage of a single-zone structure such as a detached single-family home. There are no standard test methods for measuring interzonal leakage in a two-zone or multi-zone building envelope such as might be encountered in with an attached garage or in a multifamily building. Some practitioners have been using techniques that involve making multiple measurements with a single blower door as well as combined measurements using multiple blower doors. Even for just two zones there are dozens of combinations of one-door and two-door test protocols that could conceivably be used to determine the interzonal air tightness. We examined many of these two-zone configurations using both simulation and measured data to estimate the accuracy and precision of each technique for realistic measurement scenarios. We also considered the impact of taking measurements at a single pressure versus over multiple pressures. We compared the various techniques and evaluated them for specific uses. Some techniques work better in one leakage regime; some are more sensitive to wind and other noise; some are more suited to determining only a subset of the leakage values. This paper makes recommendations on which techniques to use or not use for various cases and provides data that could be used to develop future test methods.

  18. An intensity-monitoring technique for measuring ellipsometric transients

    NARCIS (Netherlands)

    Droog, J.M.M.; Bootsma, G.A.

    1979-01-01

    Intensity-monitoring techniques make possible the measurement of rapid changes in the ellipsometric parameters. Methods used hitherto have been suitable for measuring slight changes only and require prior knowledge of the Δ and Ψ values for the initial surface. It is shown that larger changes can al

  19. Design techniques for large scale linear measurement systems

    Energy Technology Data Exchange (ETDEWEB)

    Candy, J.V.

    1979-03-01

    Techniques to design measurement schemes for systems modeled by large scale linear time invariant systems, i.e., physical systems modeled by a large number (> 5) of ordinary differential equations, are described. The techniques are based on transforming the physical system model to a coordinate system facilitating the design and then transforming back to the original coordinates. An example of a three-stage, four-species, extraction column used in the reprocessing of spent nuclear fuel elements is presented. The basic ideas are briefly discussed in the case of noisy measurements. An example using a plutonium nitrate storage vessel (reprocessing) with measurement uncertainty is also presented.

  20. Volume Measurement in Solid Objects Using Artificial Vision Technique

    Science.gov (United States)

    Cordova-Fraga, T.; Martinez-Espinosa, J. C.; Bernal, J.; Huerta-Franco, R.; Sosa-Aquino, M.; Vargas-Luna, M.

    2004-09-01

    A simple system using artificial vision technique for measuring the volume of solid objects is described. The system is based on the acquisition of an image sequence of the object while it is rotating on an automated mechanism controlled by a PC. Volumes of different objects such as a sphere, a cylinder and also a carrot were measured. The proposed algorithm was developed in environment LabView 6.1. This technique can be very useful when it is applied to measure the human body for evaluating its body composition.

  1. Optical skin friction measurement technique in hypersonic wind tunnel

    Science.gov (United States)

    Chen, Xing; Yao, Dapeng; Wen, Shuai; Pan, Junjie

    2016-10-01

    Shear-sensitive liquid-crystal coatings (SSLCCs) have an optical characteristic that they are sensitive to the applied shear stress. Based on this, a novel technique is developed to measure the applied shear stress of the model surface regarding both its magnitude and direction in hypersonic flow. The system of optical skin friction measurement are built in China Academy of Aerospace Aerodynamics (CAAA). A series of experiments of hypersonic vehicle is performed in wind tunnel of CAAA. Global skin friction distribution of the model which shows complicated flow structures is discussed, and a brief mechanism analysis and an evaluation on optical measurement technique have been made.

  2. Measurement of thermophysical properties by a pulse-heating technique

    Institute of Scientific and Technical Information of China (English)

    Peng Xiao; Jingmin Dai; Qingwei Wang

    2007-01-01

    A technique is described for the dynamic measurement of selected thermophysical properties of electrically conducting solids in the temperature range from 1100 K to the melting point. Based on rapid resistive self-heating of the specimen from room temperature to any desired high temperature in several seconds by the passage of an electical current pulse through it, this technique measures the pertinent quantities such as current, voltage, randiance temperature, with sub-millisecond time resolution. The pulse-heating technique is applied to strip specimens. The radiance temperature is measured by high-speed pyrometry,normal spectral emissivity of the strips is measured by integrating sphere reflectometry. The normal spectral emissivity results are used to compute the true temperature of the specimens. The heat capacity,electrical resistivity, total hemispherical emissivity are evaluated in the temperature range from 1100 K to the melting point.

  3. Videogrammetric Model Deformation Measurement Technique for Wind Tunnel Applications

    Science.gov (United States)

    Barrows, Danny A.

    2006-01-01

    Videogrammetric measurement technique developments at NASA Langley were driven largely by the need to quantify model deformation at the National Transonic Facility (NTF). This paper summarizes recent wind tunnel applications and issues at the NTF and other NASA Langley facilities including the Transonic Dynamics Tunnel, 31-Inch Mach 10 Tunnel, 8-Ft high Temperature Tunnel, and the 20-Ft Vertical Spin Tunnel. In addition, several adaptations of wind tunnel techniques to non-wind tunnel applications are summarized. These applications include wing deformation measurements on vehicles in flight, determining aerodynamic loads based on optical elastic deformation measurements, measurements on ultra-lightweight and inflatable space structures, and the use of an object-to-image plane scaling technique to support NASA s Space Exploration program.

  4. Linear algebraic theory of partial coherence: continuous fields and measures of partial coherence.

    Science.gov (United States)

    Ozaktas, Haldun M; Gulcu, Talha Cihad; Alper Kutay, M

    2016-11-01

    This work presents a linear algebraic theory of partial coherence for optical fields of continuous variables. This approach facilitates use of linear algebraic techniques and makes it possible to precisely define the concepts of incoherence and coherence in a mathematical way. We have proposed five scalar measures for the degree of partial coherence. These measures are zero for incoherent fields, unity for fully coherent fields, and between zero and one for partially coherent fields.

  5. Introduction of measurement techniques in ultrasonic electronics: Basic principles and recent trends

    Science.gov (United States)

    Mizutani, Koichi; Wakatsuki, Naoto; Ebihara, Tadashi

    2016-07-01

    Measurement — the act of measuring physical properties that we perform — has the potential to contribute to the successful advancement of sciences and society. To open doors in physics and other sciences, various measurement methods and related applications have been developed, and ultrasound has remained a useful probe, power source, and interesting measurement object for the past two centuries. In this paper, we first summarize the basic principles of ultrasound from the viewpoint of measurement techniques for readers who just have started studying or are interested in the field of ultrasonic electronics. Moreover, we also introduce recent studies — ultrasonic properties of materials, measurement techniques, piezoelectric devices, nonlinear acoustics, biomedical ultrasound, and ocean acoustics — and their trends related to measurement techniques in ultrasonic electronics to provide some ideas for related applications.

  6. 海洋平台钻机底座焊缝的交流电磁场检测%Detection of Critical Welds of Ocean Platform Drilling Rig Substructure Using Alternating Current Field Measurement Technique

    Institute of Scientific and Technical Information of China (English)

    葛运春; 张翼; 冷建成; 周国强; 吴泽民

    2015-01-01

    A new method using alternating current field measurement(ACFM)has been proposed in order to nondestructively inspect the critical welds of the in-service offshore platform drilling rig substructure with coatings. The detection principle of ACFM method is first introduced and is compared and analyzed with other nondestructive testing methods for surface defects,including MT and ET.Based on the structural characteristics and the special working environment of the platform drilling rig substructure,the corresponding ACFM detection system is presented,which is applied successfully to test surface or sub-surface defects of the critical welds of the rig substructure,and the scanning methods and signal recognition for the longitudinal and transversal cracks are emphatically discussed.At last,the general process and detection procedure of engineering application using ACFM method are summarized systematically,providing a good reference for ACFM inspection of other engineering structures.%为了对带有涂层的在役海洋平台钻机底座焊缝进行检测,使用了交流电磁场(ACFM)检测方法。介绍了 ACFM 检测的基本原理,并与磁粉检测、涡流检测等表面缺陷检测方法进行了对比分析。基于平台底座结构及其所处环境的特点,确定了将 ACFM 检测系统成功应用于底座关键焊缝的表面或近表面缺陷检测,重点探讨了纵向裂纹和横向裂纹的 ACFM 扫描方法和信号识别。总结了 ACFM 现场工程应用的一般流程和检测程序,对其他工程结构的 ACFM 检测具有很好的借鉴意义。

  7. A novel in-situ measuring technique for aspheric surface

    Science.gov (United States)

    Zhang, Chuan; Wang, Ping; Chen, Yaolong

    2011-11-01

    In this paper, a novel in-situ surface measuring technique for optical elements with aspheric surface is presented. It is a contact type probe, and can be used for measuring ground surfaces. The theory of this technique develops from coordinate measuring machine (CMM), and the measurement accuracy of this technique is depended on the accuracy of computer numerical controlled (CNC). By installing a special equipment with high accuracy measuring head in main spindle of CNC machine, and moving the probe along the path which is described by a mathematical aspheric expression precisely, we could get relative errors of sag height of any position in this path. With this technique, the repeat positioning error caused by traditional off-line measurement will be avoided. The author also has finished a special software with VC++ 6.0. With this software, the form error of ground work piece could be corrected rapidly. This software can calculate and handle the arrangement automatically with all parameters which are required to input in operation interface. In the correction stage, the software can analyze and process error data and generate a new NC program with corrected data for next grinding stage. After 2 or 3 times measuring and correction, the surface shape error of the aspheric optical element will be less than 1μm. The finished work piece has a very good surface finish and can be polished with high quality.

  8. Assessing the measurement of airway resistance by the interrupter technique.

    Science.gov (United States)

    Zuriarrain Reyna, Yolanda; López Neyra, Alejandro; Sanz Santiago, Verónica; Almería Gil, Esmeralda; Villa Asensi, José Ramón

    2013-12-01

    Pulmonary function tests allow an objective assessment of the degree of bronchial obstruction in collaborative subjects. The measurement of airway resistance using passive methods is very helpful in non-collaborative subjects. The objective of this study was to assess the applicability of measuring airway resistance by the interrupter technique (Rint) in pediatric subjects, determining its reproducibility, reliability and accuracy versus other techniques to measure airway resistance. Cross-sectional study in healthy children and in children with an obstructive airway disease, all aged 2-18 years old. The Rint was measured using a portable device and results were compared to airway resistance measured by oscillometry and plethysmography. The reproducibility of measurements and the infuence of the different outcome measures (use of mask or mouthpiece, cheek support, or nose clip) were assessed. Valid measurements were obtained in 82.6% of 460 children (47.6% younger than 7 years old). Reproducibility was very good (ICC= 0.9412; p measurements obtained at separate time intervals (0.75 ± 0.3 versus 0.74 ± 0.28; p= 0.435). None of the factors indicated before had an effect on the reproducibility of measurements. Resistance values obtained by plethysmography and oscillometry were higher than those obtained using the Rint, with a positive correlation between them. The higher the degree of airway obstruction, the worse the correlation with plethysmography. The Rint measurement is a plausible and reproducible technique, and has an adequate correlation with the resistance measurements obtained using oscillometry or plethysmography, thus making it useful for non-collaborative patients. In patients with airway obstruction, this technique could underestimate resistance, so it would be a hurdle to use it to follow-up subjects with a moderate to severe obstructive disease or in bronchial challenge tests.

  9. Electric Field Measurement of the Living Human Body for Biomedical Applications: Phase Measurement of the Electric Field Intensity

    Directory of Open Access Journals (Sweden)

    Ichiro Hieda

    2013-01-01

    Full Text Available The authors are developing a technique for conducting measurements inside the human body by applying a weak electric field at a radio frequency (RF. Low RF power is fed to a small antenna, and a similar antenna located 15–50 cm away measures the electric field intensity. Although the resolution of the method is low, it is simple, safe, cost-effective, and able to be used for biomedical applications. One of the technical issues suggested by the authors' previous studies was that the signal pattern acquired from measurement of a human body was essentially different from that acquired from a phantom. To trace the causes of this difference, the accuracy of the phase measurements was improved. This paper describes the new experimental system that can measure the signal phase and amplitude and reports the results of experiments measuring a human body and a phantom. The results were analyzed and then discussed in terms of their contribution to the phase measurement.

  10. Trapped field measurements of Gd-Ba-Cu-O bulk superconductor in controlled pulse field magnetizing

    Energy Technology Data Exchange (ETDEWEB)

    Ida, T [Department of Electronic Control Engineering, Hiroshima National College of Maritime Technology, 4272-1, Higashino, Ohsakikamijima-cho, Toyota-gun, Hiroshima 725-0231 (Japan); Kimura, Y; Sano, T; Yamaguchi, K; Izumi, M [Department of Marine Electronics and Mechanical Engineering, Tokyo University of Marine Science and Technology, 2-1-6, Etchu-jima, Koto-ku, Tokyo 135-8533 (Japan); Miki, M [Kitano Seiki Co. Ltd., 7-13-7, Chuo, Ohta-ku, Tokyo 143-0024 (Japan)], E-mail: ida@hiroshima-cmt.ac.jp

    2008-02-01

    For large-scale electric power application of the melt-processed high temperature superconductor (HTS) bulks, especially at rotating machine, development of trapping much higher magnetic fields by using pulsed magnetization technique is essential. It is difficult to use static field cooling (FCM) technique that is most effective magnetizing method for the general industrial HTS applications, because the FCM requires large-scale superconducting magnets. Because the rise in temperature due to the magnetic flux motion decreases the pinning force, we controlled the magnetic flux penetrating to the bulk for the effective magnetization. A couple of vortex-type copper coils applied a magnetic field to a Gd-Ba-Cu-O bulk, which dimension was 45mm in diameter and 19 mm in thickness. HTS bulk was magnetized by the controlled pulse field without passive LCR pulse. We controlled waveform by using the discharge current that IGBT chopper in pulse magnetizer intermitted. We applied the pulse magnetic field with the various risetime to the HTS bulk in liquid nitrogen. The various conditions of the controlled waveform pulse to trap well-dressed profile magnetized the Gd-Ba-Cu-O bulk, strongly at 77K. In the present study, we show several properties which was measured in the PFM of the HTS bulk.

  11. Measurement of Thermal Expansion Coefficients with Holographic Technique

    Institute of Scientific and Technical Information of China (English)

    ZhifengZhang

    1995-01-01

    A simplified mathematical model was created for measurement of thermal expansion coefficients of thin sheet materials with holographic technique.Experimental set-ups corresponding to the mathematical model were designed and built for both tests above room temperature and at low temperatures.A fringe control technique was introduced for low temperature measurements to compensate rigid body movement,THin sheet specimens of silicon and aluminum alloy(7075) were tested with the developed technique.The tested results are in good agreement with reported data and thus verify the validity of the developed technique.The Thermal expansion coefficients of the tested materials ranged from 2.5×10-60C-1 to 23.6×10-6oC-1.

  12. Application of oil-field well log interpretation techniques to the Cerro Prieto Geothermal Field

    Energy Technology Data Exchange (ETDEWEB)

    Ershaghi, I.; Phillips, L.B.; Dougherty, E.L.; Handy, L.L.

    1979-10-01

    An example is presented of the application of oil-field techniques to the Cerro Prieto Field, Mexico. The lithology in this field (sand-shale lithology) is relatively similar to oil-field systems. The study was undertaken as a part of the first series of case studies supported by the Geothermal Log Interpretation Program (GLIP) of the US Department of Energy. The suites of logs for individual wells were far from complete. This was partly because of adverse borehole conditions but mostly because of unavailability of high-temperature tools. The most complete set of logs was a combination of Dual Induction Laterolog, Compensated Formation Density Gamma Ray, Compensated Neutron Log, and Saraband. Temperature data about the wells were sketchy, and the logs had been run under pre-cooled mud condition. A system of interpretation consisting of a combination of graphic and numerical studies was used to study the logs. From graphical studies, evidence of hydrothermal alteration may be established from the trend analysis of SP (self potential) and ILD (deep induction log). Furthermore, the cross plot techniques using data from density and neutron logs may help in establishing compaction as well as rock density profile with depth. In the numerical method, R/sub wa/ values from three different resistivity logs were computed and brought into agreement. From this approach, values of formation temperature and mud filtrate resistivity effective at the time of logging were established.

  13. Single-shot measurement of the orbital-angular-momentum spectrum of partially coherent fields

    CERN Document Server

    Kulkarni, Girish; Magana-Loaiza, Omar S; Boyd, Robert W; Jha, Anand K

    2016-01-01

    We propose an image inversion-based interferometric technique for measuring the orbital-angular- momentum (OAM) spectrum of a field that is an incoherent mixture of OAM eigenstates. The tech- nique directly encodes the angular correlation function of the input field in the azimuthal intensity profile of the output interferogram. We show that for an input field with a symmetric spectrum, a single-shot acquisition of this interferogram is sufficient to measure its OAM spectrum. We first present a proof-of-concept experimental demonstration of this technique for laboratory-produced partially coherent fields with known OAM spectra. We then use this technique to measure the intrinsic OAM spectrum of the signal-idler field from parametric down-conversion over an unprece- dented range of more than 150 modes. This technique therefore surpasses all other existing mea- surement schemes in terms of efficiency and spectral range, and can have significant implications for high-dimensional optical information processing pr...

  14. Handbook of microwave component measurements with advanced VNA techniques

    CERN Document Server

    Dunsmore, Joel P

    2012-01-01

    This book provides state-of-the-art coverage for making measurements on RF and Microwave Components, both active and passive. A perfect reference for R&D and Test Engineers, with topics ranging from the best practices for basic measurements, to an in-depth analysis of errors, correction methods, and uncertainty analysis, this book provides everything you need to understand microwave measurements. With primary focus on active and passive measurements using a Vector Network Analyzer, these techniques and analysis are equally applicable to measurements made with Spectrum Analyzers or Noise Figure

  15. Near-field measurements of the even-order harmonics undetectable in far-field measurements

    Science.gov (United States)

    Moiseyev, Nimrod

    2016-12-01

    Even-order harmonics (EOHs) are generated for oriented molecules and for atoms under specific conditions. Here, we focus on the most common situations where EOHs are not observed in far-field measurements. We propose an experiment to show that the EOHs are produced close to the nucleus but are not detected in the far-field measurements due to destructive interferences of the propagated EOHs of the emitted radiation. However, Rydberg gas atoms (e.g., rubidium), which are out of the focus of the laser beam, are expected to be ionized due to their weak interaction with a specific EOH of helium, which is not observed by the far-field detector. The ionization energy of the Rydberg gas atoms should be in resonance with the single-photon energy of a specific EOH.

  16. Measurement of fuel spray vaporisation by laser techniques

    Science.gov (United States)

    Yule, A. J.; Seng, C. A.; Felton, P. G.; Ungut, A.; Chigier, N. A.

    1980-01-01

    Comparison of fuel spray structures in heated and in cold environments is made by using a new laser tomographic technique and laser anemometry. The tomography technique is shown to give accurate and rapid 'point' measurements of droplet sizes and concentrations. Experimental results show acceleration of droplets to the local gas velocity, preferential vaporisation of the smallest droplets and the dispersion of droplets by the turbulence.

  17. Thermal properties measurements in biodiesel oils using photothermal techniques

    Science.gov (United States)

    Castro, M. P. P.; Andrade, A. A.; Franco, R. W. A.; Miranda, P. C. M. L.; Sthel, M.; Vargas, H.; Constantino, R.; Baesso, M. L.

    2005-08-01

    In this Letter, thermal lens and open cell photoacoustic techniques are used to measure the thermal properties of biodiesel oils. The absolute values of the thermal effusivity, thermal diffusivity, thermal conductivity and the temperature coefficient of the refractive index were determined for samples obtained from soy, castor bean, sunflower and turnip. The results suggest that the employed techniques may be useful as complementary methods for biodiesel certification.

  18. Sound field separation with sound pressure and particle velocity measurements

    DEFF Research Database (Denmark)

    Fernandez Grande, Efren; Jacobsen, Finn; Leclère, Quentin

    2012-01-01

    separation techniques make it possible to distinguish between outgoing and incoming waves from the two sides, and thus NAH can be applied. In this paper, a separation method based on the measurement of the particle velocity in two layers and another method based on the measurement of the pressure...... and the velocity in a single layer are proposed. The two methods use an equivalent source formulation with separate transfer matrices for the outgoing and incoming waves, so that the sound from the two sides of the array can be modeled independently. A weighting scheme is proposed to account for the distance...... pressure-velocity method, although it requires an additional measurement surface. On the whole, the separation methods can be useful when the disturbance of the incoming field is significant. Otherwise the direct reconstruction is more accurate and straightforward. © 2012 Acoustical Society of America....

  19. Measuring water-vapour and carbon-dioxide fluxes at field scales with scintillometry

    NARCIS (Netherlands)

    Kesteren, van A.J.H.

    2012-01-01

    Scintillometry is a measurement technique that has proven itself to be of great value for measuring spatial-averaged fluxes of sensible heat, momentum, and evapotranspiration. Furthermore, for crop fields (field scales), scintillometry has been shown to accurately determine the sensible-heat and mom

  20. A Monopole Antenna at Optical Frequencies: Single-Molecule Near-Field Measurements

    NARCIS (Netherlands)

    Taminiau, Tim H.; Segerink, Franciscus B.; van Hulst, N.F.

    2007-01-01

    We present a monopole antenna for optical frequencies (~600 THz) and discuss near-field measurements with single fluorescent molecules as a technique to characterize such antennas. The similarities and differences between near-field antenna measurements at optical and radio frequencies are discussed

  1. Ultrasonic Technique for Density Measurement of Liquids in Extreme Conditions

    Directory of Open Access Journals (Sweden)

    Rymantas Kazys

    2015-08-01

    Full Text Available An ultrasonic technique, invariant to temperature changes, for a density measurement of different liquids under in situ extreme conditions is presented. The influence of geometry and material parameters of the measurement system (transducer, waveguide, matching layer on measurement accuracy and reliability is analyzed theoretically along with experimental results. The proposed method is based on measurement of the amplitude of the ultrasonic wave, reflected from the interface of the solid/liquid medium under investigation. In order to enhance sensitivity, the use of a quarter wavelength acoustic matching layer is proposed. Therefore, the sensitivity of the measurement system increases significantly. Density measurements quite often must be performed in extreme conditions at high temperature (up to 220 °C and high pressure. In this case, metal waveguides between piezoelectric transducer and the measured liquid are used in order to protect the conventional transducer from the influence of high temperature and to avoid depolarization. The presented ultrasonic density measurement technique is suitable for density measurement in different materials, including liquids and polymer melts in extreme conditions. A new calibration algorithm was proposed. The metrological evaluation of the measurement method was performed. The expanded measurement uncertainty Uρ = 7.4 × 10−3 g/cm3 (1%.

  2. In-situ measurement of free trace metal concentrations in a flooded paddy soil using the Donnan Membrane Technique

    NARCIS (Netherlands)

    Pan, Y.; Koopmans, G.F.; Bonten, L.T.C.; Song, J.; Luo, Y.; Temminghoff, E.J.M.; Comans, R.N.J.

    2015-01-01

    The field Donnan Membrane Technique (DMT) has been used successfully to measure in-situ free trace metal concentrations in surface waters. However, it has not been applied previously in submerged soil systems including flooded paddy rice fields.Wetested this technique in a columnexperimentwith a flo

  3. Subpixel Target Location Techniques for 3-D Coordinate Measuring System

    Institute of Scientific and Technical Information of China (English)

    2002-01-01

    The close photogrammetric 3-D coordinate measurement is a new measuring technology in the fields of the coordinate measurement machine (CMM) in recent years. In this method, we usually place some targets on the measured object and take image of targets to determine the object coordinate. The subpixel location of target image plays an important role in high accuracy 3-D coordinate measuring procedure. In this paper, some subpixel location methods are reviewed and some factors which affect location precision are analyzed. Then we propose bilinear interpolation centroid algorithm. The experiments have shown this algorithm can improve accuracy of target centroid by increasing available pixels.

  4. Reflectometry techniques for density profile measurements on fusion plasmas

    Energy Technology Data Exchange (ETDEWEB)

    Laviron, C. [Association Euratom-CEA, Centre d`Etudes de Cadarache, 13 - Saint-Paul-lez-Durance (France). Dept. de Recherches sur la Fusion Controlee; Donne, A.J.H. [Associatie Euratom-FOM, Nieuwegein (Netherlands). FOM-Instituut voor Plasmafysica; Manso, M.E. [Instituto Superior Tecnico, Lisbon (Portugal). Lab. de Quimica Organica; Sanchez, J. [EURATOM-CIEMAT for Fusion Association, Madrid (Spain)

    1996-03-01

    Reflectometry applied to the measurement of density profiles on fusion plasmas has been subject to many recent developments. After a brief reminder of the principles of reflectometry, the theoretical accuracy of reflectometry measurements is discussed. The main difficulties limiting the performance, namely the plasma fluctuations and the quality of the transmission lines, are analysed. The different techniques used for reflectometry are then presented. The present status and achievements of actual implementations of these techniques are shown, with an analysis of their respective limitations and merits, as well as foreseen developments. (author). 70 refs.

  5. A Técnica Q - como instrumento de medida na área da educação em saúde The Q - technique as a measuring tool in the public health education field

    Directory of Open Access Journals (Sweden)

    Maria Aparecida Balduino

    1986-02-01

    Stephenson's Q-technique, was elaborated, By using this tool it was planned to carry out a study on the function perception of the public health educator on the health team. The study comprises two phases: the first dealing with the construction of the instrument it self and the second with the making of a research survey, using the same. It is described every step of the first phase which consists of: gathering of information on the function assigned to the public health educator; list of the functions; turning them into statements transcribed into cards; selection of a sample of 70 cards, by a highly specialized board of judges; tabulation of the data obtained and definition of the definitive instrument. To fulfil the requisites of validity the scaling distribution should present a certain balance among the pertinent, intermediate, and non-pertinent statements. For statistical convenience and to guarantee such a balance each judge is told to place varying numbers of cards on several piles, turning its totality into a continuum approaching a normal or nearly normal distribution. Such a balance has been attained and a distribution of the frequency statements sampled by the judges has shown an excellent internal agreement which qualifies this study as satisfactory. The statements have been proved to be definitive components of the measuring tool - Percepção da Função do Educador na Saúde Pública (Perception of the Function of the Educator in Public Health.

  6. Field in field technique in two-dimensional planning for whole brain irradiation; Tecnica field in field em planejamentos bidimensionais para irradiacao de cerebro total

    Energy Technology Data Exchange (ETDEWEB)

    Castro, A.L.S.; Campos, T.P.R., E-mail: radioterapia.andre@gmail.com [Universidade Federal de Minas Gerais (UFMG), Belo Horizonte (Brazil). Departamento de Engenharia Nuclear

    2016-11-01

    Radiotherapy is the most used clinical method used for brain metastases treatment, the most frequent secondary tumors provided by breast, lung and melanomas as primary origin. The protocols often use high daily doses and, depending on the irradiation technique there is high probability of complications in health tissues. In order to minimize adverse effects, it is important the dosimetric analysis of three-dimensional radiotherapy planning through tomographic images or, concerning to the 2D simulations, by the application of techniques that optimize dose distribution by increasing the homogeneity. The study aimed to compare the 2D and 3D conformal planning for total brain irradiation in a individual equivalent situation and evaluate the progress of these planning applying the field in field technique. The methodology consisted of simulating a two-dimensional planning, reproduce it on a set of tomographic images and compare it with the conformal plan for two fields and four fields (field in field). The results showed no significant difference between 2D and 3D planning for whole brain irradiation, and the field in field technique significantly improved the dose distribution in brain volume compared with two fields for the proposal situation. As conclusion, the two-dimensional plane for the four fields described was viable for whole brain irradiation in the treatment of brain metastases at the proposal situation. (author)

  7. SU-E-T-404: Simple Field-In-Field Technique for Total Body Irradiation in Large Patients

    Energy Technology Data Exchange (ETDEWEB)

    Chi, P; Pinnix, C; Dabaja, B; Wang, C; Aristophanous, M; Tung, S [UT MD Anderson Cancer Center, Houston, TX (United States)

    2014-06-01

    Purpose: A simple Field-in-Field technique for Total Body Irradiation (TBI) was developed for traditional AP/PA TBI treatments to improve dosimetric uniformity in patients with large separation. Methods: TBI at our institution currently utilizes an AP/PA technique at an extended source-to-surface distance (SSD) of 380cm with patients in left decubitus position during the AP beam and in right decubitus during the PA beam. Patients who have differences in thickness (separation) between the abdomen and head greater than 10cm undergo CT simulation in both left and right decubitus treatment positions. One plan for each CT is generated to evaluate dose to patient midline with both AP and PA fields, but only corresponding AP fields will be exported for treatment for patient left decubitus position and PA fields for patient right decubitus position. Subfields are added by collimating with the x-ray jaws according to separation changes at 5–7% steps to minimize hot regions to less than 10%. Finally, the monitor units (MUs) for the plans are verified with hand calculation and water phantom measurements. Results: Dose uniformity (+/−10%) is achieved with field-in-field using only asymmetric jaws. It is dosimetrically robust with respect to minor setup/patient variations inevitable due to patient conditions. MUs calculated with Pinnacle were verified in 3 clinical cases and only a 2% difference was found compared to homogeneous calculation. In-vivo dosimeters were also used to verify doses received by each patient with and confirmed dose variations less than 10%. Conclusion: We encountered several cases with separation differences that raised uniformity concerns — based on a 1% dose difference per cm separation difference assumption. This could Resultin an unintended hot spot, often in the head/neck, up to 25%. This method allows dose modulation without adding treatment complexity nor introducing radiobiological variations, providing a reasonable solution for this unique

  8. Wideband Phase Retrieval Technique from Amplitude-Only Near-Field Data

    Directory of Open Access Journals (Sweden)

    G. D. Massa

    2008-12-01

    Full Text Available A wideband frequency behavior is demonstrated for a phaseless near-field technique of basically interferometric approach, which uses two identical probes interfering each other through a microstrip circuit and performing amplitude-only near-field measurements on a single scanning surface. The phase retrieval procedure is properly formulated to take into account the frequency dependence without changing neither the microstrip circuit nor the distance between the probes. Numerical simulations on a linear array of elementary sources are presented to validate the theoretical results.

  9. Infrared Spectroscopy of Explosives Residues: Measurement Techniques and Spectral Analysis

    Energy Technology Data Exchange (ETDEWEB)

    Phillips, Mark C.; Bernacki, Bruce E.

    2015-03-11

    Infrared laser spectroscopy of explosives is a promising technique for standoff and non-contact detection applications. However, the interpretation of spectra obtained in typical standoff measurement configurations presents numerous challenges. Understanding the variability in observed spectra from explosives residues and particles is crucial for design and implementation of detection algorithms with high detection confidence and low false alarm probability. We discuss a series of infrared spectroscopic techniques applied toward measuring and interpreting the reflectance spectra obtained from explosives particles and residues. These techniques utilize the high spectral radiance, broad tuning range, rapid wavelength tuning, high scan reproducibility, and low noise of an external cavity quantum cascade laser (ECQCL) system developed at Pacific Northwest National Laboratory. The ECQCL source permits measurements in configurations which would be either impractical or overly time-consuming with broadband, incoherent infrared sources, and enables a combination of rapid measurement speed and high detection sensitivity. The spectroscopic methods employed include standoff hyperspectral reflectance imaging, quantitative measurements of diffuse reflectance spectra, reflection-absorption infrared spectroscopy, microscopic imaging and spectroscopy, and nano-scale imaging and spectroscopy. Measurements of explosives particles and residues reveal important factors affecting observed reflectance spectra, including measurement geometry, substrate on which the explosives are deposited, and morphological effects such as particle shape, size, orientation, and crystal structure.

  10. Swept frequency technique for dispersion measurement of microstrip lines

    Science.gov (United States)

    Lee, Richard Q.

    1987-01-01

    Microstrip lines used in microwave integrated circuits are dispersive. Because a microstrip line is an open structure, the dispersion can not be derived with pure TEM, TE, or TM mode analysis. Dispersion analysis has commonly been done using a spectral domain approach, and dispersion measurement has been made with high Q microstrip ring resonators. Since the dispersion of a microstrip line is fully characterized by the frequency dependent phase velocity of the line, dispersion measurement of microstrip lines requires the measurement of the line wavelength as a function of frequency. In this paper, a swept frequency technique for dispersion measurement is described.

  11. Measurement of moisture in materials. Fundamentals - measuring techniques - applications - standards; Materialfeuchtemessung. Grundlagen - Messverfahren - Applikationen - Normen

    Energy Technology Data Exchange (ETDEWEB)

    Kupfer, K.; Knoechel, R.; Menke, F.; Krus, M.; Koch, W.; Brokmann, T.; Stopp, H.; Kahle, M.; Bachmann, C.; Goeller, A.; Leschnik, W.; Hauenschild, C.; Herrmann, R.; Klein, A.; Neue, J.; Haeupl, P.; Eggers, R.; Sikora, J.; Fechner, H.; Boltze, T.; Hinz, T.; Vogt, O.

    1997-12-31

    The book deals with fundamentals of moisture measurement, the physical properties of water/solids mixtures, but also reference methods such as the drying closet method, microwave drying, infrared drying, and Karl-Fischer titration. Competent experts present current methods of conductimetry, capacitive measuring techniques, microwave measuring techniques, nuclear resonance measuring techniques, nuclear radiometry techniques, infrared measuring techniques, thermal conductivity measurement techniques and hygrometric techniques. Apart from the physical bases, the authors look at factors of interference, measuring systems, as well as applications. Microwave measuring techniques offer the advantages of non-destructive measurement, independence of salt content, and density compensation. (orig./MM) 260 figs., 19 tabs., 386 refs. [Deutsch] Das Buch behandelt Grundlagen der Feuchtemessung, physikalische Eigenschaften von Wasser-Feststoff-Gemischen, aber auch Referenzverfahren, wie Trockenschrankverfahren, Mikrowellentrocknung, Infrarottrocknung und Karl-Fischer-Titration. Von kompetenten Fachleuten werden die in der Praxis ueblichen Leitfaehigkeitsmessverfahren, kapazitiven Messverfahren, Mikrowellenmessverfahren, Kernresonanzverfahren, Kernstrahlungsverfahren, Infrarot-Messverfahren, Waermeleitfaehigkeitsmessverfahren und hydrometrischen Messverfahren vorgestellt. Es werden sowohl physikalische Grundlagen, Stoergroessen, Messsysteme, aber auch Applikationen behandelt. Mikrowellenmessverfahren bieten Vorteile einer zerstoerungsfreien Messung, der Unabhaengigkeit vom Salzgehalt und Moeglichkeiten der Dichtekompensation. (orig./MM)

  12. Chopped nonlinear magneto-optic rotation: a technique for precision measurements

    CERN Document Server

    Ravishankar, Harish; Natarajan, Vasant

    2011-01-01

    We have developed a technique for precise measurement of small magnetic fields using nonlinear magneto-optic rotation (NMOR). The technique relies on the resonant laser beam being chopped. During the on time, the atoms are optically pumped into an aligned ground state ($\\Delta m=2$ coherence). During the off time, they freely precess around the magnetic field at the Larmor frequency. If the on-off modulation frequency matches (twice) the Larmor precession frequency, the rotation is resonantly enhanced in every cycle, thereby making the process like a repeated Ramsey measurement of the Larmor frequency. We study chopped-NMOR in a paraffin-coated Cs vapor cell. The out-of-phase demodulated rotation shows a Lorentzian peak of linewidth 85 $\\mu$G, corresponding to a sensitivity of 0.15 nG/$\\sqrt{{\\rm Hz}}$. We discuss the potential of this technique for the measurement of an atomic electric-dipole moment.

  13. Method and apparatus for measuring weak magnetic fields

    DEFF Research Database (Denmark)

    1995-01-01

    When measuring weak magnetic fields, a container containing a medium, such as a solution containing a stable radical, is placed in a polarising magnetic field, which is essentially at right angles to the field to be measured. The polarising field is interrupted rapidly, the interruption being...

  14. Solar coronal magnetic fields derived using seismology techniques applied to omnipresent sunspot waves

    CERN Document Server

    Jess, D B; Ryans, R S I; Christian, D J; Keys, P H; Mathioudakis, M; Mackay, D H; Prasad, S Krishna; Banerjee, D; Grant, S D T; Yau, S; Diamond, C

    2016-01-01

    Sunspots on the surface of the Sun are the observational signatures of intense manifestations of tightly packed magnetic field lines, with near-vertical field strengths exceeding 6,000 G in extreme cases. It is well accepted that both the plasma density and the magnitude of the magnetic field strength decrease rapidly away from the solar surface, making high-cadence coronal measurements through traditional Zeeman and Hanle effects difficult since the observational signatures are fraught with low-amplitude signals that can become swamped with instrumental noise. Magneto-hydrodynamic (MHD) techniques have previously been applied to coronal structures, with single and spatially isolated magnetic field strengths estimated as 9-55 G. A drawback with previous MHD approaches is that they rely on particular wave modes alongside the detectability of harmonic overtones. Here we show, for the first time, how omnipresent magneto-acoustic waves, originating from within the underlying sunspot and propagating radially outwa...

  15. Measurements of stellar magnetic fields with the autocorrelation of spectra

    CERN Document Server

    Borra, Ermanno F

    2015-01-01

    We present a novel technique that uses the autocorrelation of the spectrum of a star to measure the line broadening caused by the modulus of its average surface magnetic field. The advantage of the autocorrelation comes from the fact that it can detect very small spectral line broadening effects because it averages over many spectral lines and therefore gives an average with a very high signal to noise ratio. We validate the technique with the spectra of known magnetic stars and obtain autocorrelation curves that are in full agreement with published magnetic curves obtained with Zeeman splitting. The autocorrelation also gives less noisy curves so that it can be used to obtain very accurate curves. We degrade the resolution of spectra of these magnetic stars to lower spectral resolutions where the Zeeman splitting is undetectable. At these resolutions, the autocorrelation still gives good quality curves, thereby showing that it can be used to measure magnetic fields in spectra where the Zeeman splitting is si...

  16. Measurement of two-dimensional Doppler wind fields using a field widened Michelson interferometer.

    Science.gov (United States)

    Langille, Jeffery A; Ward, William E; Scott, Alan; Arsenault, Dennis L

    2013-03-10

    An implementation of the field widened Michelson concept has been applied to obtain high resolution two-dimensional (2D) images of low velocity (<50 m/s) Doppler wind fields in the lab. Procedures and techniques have been developed that allow Doppler wind and irradiance measurements to be determined on a bin by bin basis with an accuracy of less than 2.5 m/s from CCD images over the observed field of view. The interferometer scanning mirror position is controlled to subangstrom precision with subnanometer repeatability using the multi-application low-voltage piezoelectric instrument control electronics developed by COM DEV Ltd.; it is the first implementation of this system as a phase stepping Michelson. In this paper the calibration and characterization of the Doppler imaging system is described and the planned implementation of this new technique for imaging 2D wind and irradiance fields using the earth's airglow is introduced. Observations of Doppler winds produced by a rotating wheel are reported and shown to be of sufficient precision for buoyancy wave observations in airglow in the mesopause region of the terrestrial atmosphere.

  17. Updates on measurements and modeling techniques for expendable countermeasures

    Science.gov (United States)

    Gignilliat, Robert; Tepfer, Kathleen; Wilson, Rebekah F.; Taczak, Thomas M.

    2016-10-01

    The potential threat of recently-advertised anti-ship missiles has instigated research at the United States (US) Naval Research Laboratory (NRL) into the improvement of measurement techniques for visual band countermeasures. The goal of measurements is the collection of radiometric imagery for use in the building and validation of digital models of expendable countermeasures. This paper will present an overview of measurement requirements unique to the visual band and differences between visual band and infrared (IR) band measurements. A review of the metrics used to characterize signatures in the visible band will be presented and contrasted to those commonly used in IR band measurements. For example, the visual band measurements require higher fidelity characterization of the background, including improved high-transmittance measurements and better characterization of solar conditions to correlate results more closely with changes in the environment. The range of relevant engagement angles has also been expanded to include higher altitude measurements of targets and countermeasures. In addition to the discussion of measurement techniques, a top-level qualitative summary of modeling approaches will be presented. No quantitative results or data will be presented.

  18. Measurement of wheelchair rolling resistance with a handle bar push technique

    NARCIS (Netherlands)

    van der Woude, L H V; Geurts, C; Winkelman, H; Veeger, DirkJan (H. E. J.)

    2003-01-01

    The purpose of this study was to evaluate a technique of pushing a wheelchair at the level of the handle bars as a method for measuring rolling resistance of wheelchair-user systems under different field conditions. Under standardized conditions on a motor driven treadmill, rolling resistance was de

  19. Measurement of wheelchair rolling resistance with a handle bar push technique

    NARCIS (Netherlands)

    van der Woude, L H V; Geurts, C; Winkelman, H; Veeger, DirkJan (H. E. J.)

    2003-01-01

    The purpose of this study was to evaluate a technique of pushing a wheelchair at the level of the handle bars as a method for measuring rolling resistance of wheelchair-user systems under different field conditions. Under standardized conditions on a motor driven treadmill, rolling resistance was

  20. Companding technique for high dynamic range measurements using gafchromic films

    CERN Document Server

    Heuvel, Frank Van den; Defraene, Gilles

    2011-01-01

    We propose a methodology to perform dose measurements using gafchromic films which can span several decades of dose levels. The technique is based on a rescaling approach using different films irradiated at different dose levels. This is combined with a registration protocol correcting positioning and scaling factors for each film.

  1. Correlation techniques for the improvement of signal-to-noise ratio in measurements with stochastic processes

    CERN Document Server

    Reddy, V R; Reddy, T G; Reddy, P Y; Reddy, K R

    2003-01-01

    An AC modulation technique is described to convert stochastic signal variations into an amplitude variation and its retrieval through Fourier analysis. It is shown that this AC detection of signals of stochastic processes when processed through auto- and cross-correlation techniques improve the signal-to-noise ratio; the correlation techniques serve a similar purpose of frequency and phase filtering as that of phase-sensitive detection. A few model calculations applied to nuclear spectroscopy measurements such as Angular Correlations, Mossbauer spectroscopy and Pulse Height Analysis reveal considerable improvement in the sensitivity of signal detection. Experimental implementation of the technique is presented in terms of amplitude variations of harmonics representing the derivatives of normal spectra. Improved detection sensitivity to spectral variations is shown to be significant. These correlation techniques are general and can be made applicable to all the fields of particle counting where measurements ar...

  2. Doppler lidar wind measurement with the edge technique

    Science.gov (United States)

    Korb, C. Laurence; Gentry, Bruce M.

    1992-01-01

    The edge technique is a new and powerful method for measuring small frequency shifts. Range resolved lidar measurements of winds can be made with high accuracy and high vertical resolution using the edge technique to measure the Doppler shift of an atmospheric backscattered signal from a pulsed laser. The edge technique can be used at near-infrared or visible wavelengths using well developed solid state lasers and detectors with various edge filters. In the edge technique, the laser frequency is located on the steep slope of the spectral response function of a high resolution optical filter. Due to the steep slope of the edge, very small frequency shifts cause large changes in measured signal. The frequency of the outgoing laser pulse is determined by measuring its location on the edge of the filter. This is accomplished by sending a small portion of the beam to the edge detection setup where the incoming light is split into two channels - an edge filter and an energy monitor channel. The energy monitor signal is used to normalize the edge filter signal for magnitude. The laser return backscattered from the atmosphere is collected by a telescope and directed through the edge detection setup to determine its frequency (location on the edge) in a similar manner for each range element. The Doppler shift, and thus the wind, is determined from a differential measurement of the frequency of the outgoing laser pulse and the frequency of the laser return backscattered from the atmosphere. We have conducted simulations of the performance of an edge lidar system using an injection seeded pulsed Nd:YAG laser at 1.06 microns. The central fringe of a Fabry-Perot etalon is used as a high resolution edge filter to measure the shift of the aerosol return.

  3. Accurate Fiber Length Measurement Using Time-of-Flight Technique

    Science.gov (United States)

    Terra, Osama; Hussein, Hatem

    2016-06-01

    Fiber artifacts of very well-measured length are required for the calibration of optical time domain reflectometers (OTDR). In this paper accurate length measurement of different fiber lengths using the time-of-flight technique is performed. A setup is proposed to measure accurately lengths from 1 to 40 km at 1,550 and 1,310 nm using high-speed electro-optic modulator and photodetector. This setup offers traceability to the SI unit of time, the second (and hence to meter by definition), by locking the time interval counter to the Global Positioning System (GPS)-disciplined quartz oscillator. Additionally, the length of a recirculating loop artifact is measured and compared with the measurement made for the same fiber by the National Physical Laboratory of United Kingdom (NPL). Finally, a method is proposed to relatively correct the fiber refractive index to allow accurate fiber length measurement.

  4. Precision insolation measurement under field conditions

    Science.gov (United States)

    Reid, M. S.; Gardner, R. A.

    1977-01-01

    Work at the Jet Propulsion Laboratory had resulted in the development of a primary absolute cavity radiometer (PACRAD), which was recently accepted as an international standard of irradiance. The development of an wall-weather, field-worthy solar radiometer based on the PACRAD is discussed, and its calibration stability over a two-year period in the field is described.

  5. A Novel Microcharacterization Technique in the Measurement of Strain and Orientation Gradient in Advanced Materials

    Science.gov (United States)

    Garmestai, H.; Harris, K.; Lourenco, L.

    1997-01-01

    Representation of morphology and evolution of the microstructure during processing and their relation to properties requires proper experimental techniques. Residual strains, lattice distortion, and texture (micro-texture) at the interface and the matrix of a layered structure or a functionally gradient material and their variation are among parameters important in materials characterization but hard to measure with present experimental techniques. Current techniques available to measure changes in interred material parameters (residual stress, micro-texture, microplasticity) produce results which are either qualitative or unreliable. This problem becomes even more complicated in the case of a temperature variation. These parameters affect many of the mechanical properties of advanced materials including stress-strain relation, ductility, creep, and fatigue. A review of some novel experimental techniques using recent advances in electron microscopy is presented here to measure internal stress, (micro)texture, interracial strength and (sub)grain formation and realignment. Two of these techniques are combined in the chamber of an Environmental Scanning Electron Microscope to measure strain and orientation gradients in advanced materials. These techniques which include Backscattered Kikuchi Diffractometry (BKD) and Microscopic Strain Field Analysis are used to characterize metallic and intermetallic matrix composites and superplastic materials. These techniques are compared with the more conventional x-ray diffraction and indentation techniques.

  6. Field Emission Measurements from Niobium Electrodes

    Energy Technology Data Exchange (ETDEWEB)

    M. BastaniNejad, P.A. Adderley, J. Clark, S. Covert, J. Hansknecht, C. Hernandez-Garcia, R. Mammei, M. Poelker

    2011-03-01

    Increasing the operating voltage of a DC high voltage photogun serves to minimize space charge induced emittance growth and thereby preserve electron beam brightness, however, field emission from the photogun cathode electrode can pose significant problems: constant low level field emission degrades vacuum via electron stimulated desorption which in turn reduces photocathode yield through chemical poisoning and/or ion bombardment and high levels of field emission can damage the ceramic insulator. Niobium electrodes (single crystal, large grain and fine grain) were characterized using a DC high voltage field emission test stand at maximum voltage -225kV and electric field gradient > 10MV/m. Niobium electrodes appear to be superior to diamond-paste polished stainless steel electrodes.

  7. An EIRP Measurement Method for Base-Station Antennas Using Field Strengths Measured along a Single Straight Line

    Directory of Open Access Journals (Sweden)

    Soon-Soo Oh

    2013-01-01

    Full Text Available We describe an EIRP measurement technique for a base-station antenna. The proposed method especially can be applied to the base-station antenna installed in real environments. Fresnel region measurement method is an optimal technique to avoid the far-field multipath interference, and, furthermore, it could shorten the measurement time. For detecting only the field strengths along a single straight line, we also propose a simple phase-retrieval method. For verification, a simulation and experiment have been performed. An anechoic chamber was utilized in this paper before the real environment test with the outdoor measurement system. The transformed far-field pattern and EIRP agree closely with the reference data within a valid angle. The proposed method can be applied for the EIRP in situ measurements without moving a vehicle loading the EIRP measurement apparatus.

  8. 4. Workshop - Measurement techniques of stationary and transient multiphase flow

    Energy Technology Data Exchange (ETDEWEB)

    Prasser, H.M. (ed.)

    2001-05-01

    In November 2000, the 4th Workshop on Measurement Techniques for Stationary and Transient Multiphase Flows took place in Rossendorf. Three previous workshops of this series were national meetings; this time participants from different countries took part. The programme comprised 14 oral presentations, 9 of which are included in these proceedings in full length. A special highlight of the meeting was the main lecture ''Ultrasonic doppler method for bubbly flow measurement'' of Professor Masanori Aritomi, Dr. Hiroshige Kikura and Dr. Yumiko Suzuki. The workshop again dealt with high-resolution phase distribution and phase velocity measurement techniques based on electrical conductivity, ultrasound, laser light and high-speed cinematography. A number of presentations were dedicated to the application of wire-mesh sensors developed by FZR for different applications used by the Technical Universities of Delft and Munich and the Tokyo Institute of Technology. (orig.)

  9. Electropyroelectric technique for measurement of the thermal effusivity of liquids

    Energy Technology Data Exchange (ETDEWEB)

    Ivanov, R; Moreno, I; Araujo, C [Facultad de Fisica, Universidad Autonoma de Zacatecas, Calz. Solidaridad Esquina Paseo de la Bufa s/n, C. P. 98060, Zacatecas, Zac. (Mexico); Marin, E, E-mail: emarin63@yahoo.e, E-mail: emarinm@ipn.m [Centro de Investigacion en Ciencia Aplicada y TecnologIa Avanzada, Instituto Politecnico Nacional, LegarIa 694, Colonia Irrigacion, C. P. 11500, Mexico D. F. (Mexico)

    2010-06-09

    The photopyroelectric method has been recognized as a reliable and useful tool for the measurement of the thermal properties of condensed matter samples. Usually the photothermal signal is generated using intensity modulated light beams, whose amplitudes are difficult to maintain stable. In this paper we describe a variant of this technique that uses amplitude modulated electrical current as excitation source, via Joule heating of the metal contact on one side of the pyroelectric sensor. The possibilities of this method, called by us the electropyroelectric technique, for thermal effusivity measurements of liquid samples are shown using test samples of distilled water, ethanol and glycerine. The results obtained for this parameter agree well with the values reported in the literature. Our measurement uncertainties are about 3%, a fact that opens several possible applications.

  10. Soil volumetric water content measurements using TDR technique

    Directory of Open Access Journals (Sweden)

    S. Vincenzi

    1996-06-01

    Full Text Available A physical model to measure some hydrological and thermal parameters in soils will to be set up. The vertical profiles of: volumetric water content, matric potential and temperature will be monitored in different soils. The volumetric soil water content is measured by means of the Time Domain Reflectometry (TDR technique. The result of a test to determine experimentally the reproducibility of the volumetric water content measurements is reported together with the methodology and the results of the analysis of the TDR wave forms. The analysis is based on the calculation of the travel time of the TDR signal in the wave guide embedded in the soil.

  11. High resolution resonant recombination measurements using evaporative cooling technique

    Energy Technology Data Exchange (ETDEWEB)

    Beilmann, C; Lopez-Urrutia, J R Crespo; Mokler, P H; Ullrich, J, E-mail: christian.beilmann@mpi-hd.mpg.d [Max-Planck-Institut fuer Kernphysik, Saupfercheckweg 1, 69117 Heidelberg (Germany)

    2010-09-15

    We report on a method significantly improving the energy resolution of dielectronic recombination (DR) measurements in electron beam ion traps (EBITs). The line width of DR resonances can be reduced to values distinctly smaller than the corresponding space charge width of the uncompensated electron beam. The experimental technique based on forced evaporative cooling is presented together with test measurements demonstrating its high efficiency. The principle for resolution improvement is elucidated and the limiting factors are discussed. This method opens access to high resolution DR measurements at high ion-electron collision energies required for innermost shell DR in highly charged ions (HCI).

  12. Vibration measurement based on the optical cross-correlation technique with femtosecond pulsed laser

    Science.gov (United States)

    Han, Jibo; Wu, Tengfei; Zhao, Chunbo; Li, Shuyi

    2016-10-01

    Two vibration measurement methods with femtosecond pulsed laser based on the optical cross-correlation technique are presented independently in this paper. The balanced optical cross-correlation technique can reflect the time jitter between the reference pluses and measurement pluses by detecting second harmonic signals using type II phase-matched nonlinear crystal and balanced amplified photo-detectors. In the first method, with the purpose of attaining the vibration displacement, the time difference of the reference pulses relative to the measurement pluses can be measured using single femtosecond pulsed laser. In the second method, there are a couple of femtosecond pulsed lasers with high pulse repetition frequency. Vibration displacement associated with cavity length can be calculated by means of precisely measuring the pulse repetition frequency. The results show that the range of measurement attains ±150μm for a 500fs pulse. These methods will be suited for vibration displacement measurement, including laboratory use, field testing and industrial application.

  13. Study on the Variational Assimilation Technique for the Retrieval of Wind Fields from Doppler Radar Data

    Institute of Scientific and Technical Information of China (English)

    WAN Qilin; XUE Jishan; ZHUANG Shiyu

    2006-01-01

    This paper introduces a variational assimilation technique for the retrieval of wind fields from Doppler radar data. The assimilated information included both the radial velocity (RV) and the movement of radar echo. In this assimilation technique, the key is transforming the movement of radar echo to a new radar measuring variable- "apparent velocity" (AV). Thus, the information of wind is added, and the indeterminacy of recovering two-dimensional wind only by AV was overcome effectively by combining RV with AV. By means of CMA GRAPES-3Dvar and CINRAD data, some experiments were performed. The results show that the method of retrieval of wind fields is useful in obtaining the construction of the weather system.

  14. Plasma scattering of electromagnetic radiation theory and measurement techniques

    CERN Document Server

    Froula, Dustin H; Luhmann, Neville C Jr; Sheffield, John

    2011-01-01

    This work presents one of the most powerful methods of plasma diagnosis in exquisite detail to guide researchers in the theory and measurement techniques of light scattering in plasmas. Light scattering in plasmas is essential in the research and development of fusion energy, environmental solutions, and electronics.Referred to as the "Bible" by researchers the work encompasses fusion and industrial applications essential in plasma research. It is the only comprehensive resource specific to the plasma scattering technique. It provides a wide-range of experimental examples and discussion of the

  15. Novel On-wafer Radiation Pattern Measurement Technique for MEMS Actuator Based Reconfigurable Patch Antennas

    Science.gov (United States)

    Simons, Rainee N.

    2002-01-01

    The paper presents a novel on-wafer, antenna far field pattern measurement technique for microelectromechanical systems (MEMS) based reconfigurable patch antennas. The measurement technique significantly reduces the time and the cost associated with the characterization of printed antennas, fabricated on a semiconductor wafer or dielectric substrate. To measure the radiation patterns, the RF probe station is modified to accommodate an open-ended rectangular waveguide as the rotating linearly polarized sampling antenna. The open-ended waveguide is attached through a coaxial rotary joint to a Plexiglas(Trademark) arm and is driven along an arc by a stepper motor. Thus, the spinning open-ended waveguide can sample the relative field intensity of the patch as a function of the angle from bore sight. The experimental results include the measured linearly polarized and circularly polarized radiation patterns for MEMS-based frequency reconfigurable rectangular and polarization reconfigurable nearly square patch antennas, respectively.

  16. Study of Influence of Experimental Technique on Measured Particle Velocity Distributions in Fluidized Bed

    Science.gov (United States)

    Gopalan, Balaji; Shaffer, Frank

    2013-11-01

    Fluid flows that are loaded with high concentration of solid particles are common in oil and chemical processing industries. However, the opaque nature of the flow fields and the complex nature of the flow have hampered the experimental and computational study of these processes. This has led to the development of a number of customized experimental techniques for high concentration particle flows for evaluation and improvement of CFD models. This includes techniques that track few individual particles, measures average particle velocity over a small sample volume and those over a large sample volume. In this work novel high speed PIV (HsPIV), with individual particle tracking, was utilized to measure velocities of individual particles in gas-particle flow fields at the walls circulating and bubbling fluidized bed. The HsPIV measurement technique has the ability to simultaneously recognize and track thousands of individual particles in flows of high particle concentration. To determine the effect of the size of the sample volume on particle velocity measurements, the PDF of Lagrangian particle velocity was compared with the PDF of Eulerian for different domain sizes over a range of flow conditions. The results will show that measured particle velocity distribution can vary from technique to technique and this bias has to be accounted in comparison with CFD simulations.

  17. A simple technique for measuring rainfall interception by small shrub: interception flow collection box

    Science.gov (United States)

    Belmonte Serrato, F.; Romero Diaz, A.

    1998-03-01

    In this paper a simple technique for field measurement of rain water loss arising from interception and water flows associated with species of small Mediterranean shrub is described: the interception flow collection box. This technique solves the problem of installing devices to control stemflow in species with a multiple trunk and demonstrates its efficiency through the results obtained from the data observed for three species of semi-arid Mediterranean shrub: Juniperus oxycedrus, Rosmarinus officinalis and Thymus vulgaris. Finally, the empirical equations for the prediction of throughfall, stemflow and rain water loss through interception are presented for the three selected species and the validity of the technique employed is established.

  18. Measuring vector magnetic fields in solar prominences

    CERN Document Server

    Suárez, D Orozco; Bueno, J Trujillo

    2012-01-01

    We present spectropolarimetric observations in the He I 1083.0 nm multiplet of a quiescent, hedgerow solar prominence. The data were taken with the Tenerife Infrared Polarimeter attached to the German Vacuum Tower Telescope at the Observatorio del Teide (Tenerife; Canary Islands; Spain). The observed He I circular and linear polarization signals are dominated by the Zeeman effect and by atomic level polarization and the Hanle effect, respectively. These observables are sensitive to the strength and orientation of the magnetic field vector at each spatial point of the field of view. We determine the magnetic field vector of the prominence by applying the HAZEL inversion code to the observed Stokes profiles. We briefly discuss the retrieved magnetic field vector configuration.

  19. Gravimetric Measurement of Magnetic Field Gradient Spatial Distribution

    CERN Document Server

    Arutunian, S G; Egiazarian, S L; Mailian, M R; Sinenko, I G; Sinjavski, A V; Vasiniuk, I E

    1999-01-01

    Magnetic interaction between a weighing sample and an external magnetic field allows to measure characteristics of magnetic field (a sample with known magnetic characteristics), as well as the magnetic properties of a sample (a known magnetic field). Measurement of materials magnetic permeability is a well known application of this method. In this paper we restrict ourselves to the measurement of magnetic field spatial distribution, which was achieved by scanning of samples from known materials along the vertical axis. Field measurements by Hall detector were done to calibrate obtained data. Such measurements are of great interest in some branches of physics, in particular, in accelerator physics, where the quality of magnetic system parts eventually determine the quality of accelerated bunches. Development of a simple and cheep device for measurement of magnetic field spatial distribution is an urgent problem. The developed system for gravimetric measurement of magnetic field gradients partially solves this ...

  20. The advance and development of damage measurement technique of rock

    Institute of Scientific and Technical Information of China (English)

    YANG Geng-she(杨更社)

    2003-01-01

    The key problem of rock damage mechanics is that determination of the variable of rock damage and the establishment of damage constitutive relation of rock, which is inevitable involved in the measurement problem of rock. In this paper, the measurement technology and method of rock damage are comprehensively narrated, analyzed and studied. On the basis of the narrating the former study, a new method (Computerized Tomography,CT for short) is introduced, which is applied to rock damage measurement. On the other hand, some newest study results and laws in the field are also introduced, which are from some scholars, the author of this paper.

  1. Unit vent airflow measurements using a tracer gas technique

    Energy Technology Data Exchange (ETDEWEB)

    Adams, D.G. [Union Electric Company, Fulton, MO (United States); Lagus, P.L. [Lagus Applied Technology, Inc., San Diego, CA (United States); Fleming, K.M. [NCS Corp., Columbus, OH (United States)

    1997-08-01

    An alternative method for assessing flowrates that does not depend on point measurements of air flow velocity is the constant tracer injection technique. In this method one injects a tracer gas at a constant rate into a duct and measures the resulting concentration downstream of the injection point. A simple equation derived from the conservation of mass allows calculation of the flowrate at the point of injection. Flowrate data obtained using both a pitot tube and a flow measuring station were compared with tracer gas flowrate measurements in the unit vent duct at the Callaway Nuclear Station during late 1995 and early 1996. These data are presented and discussed with an eye toward obtaining precise flowrate data for release rate calculations. The advantages and disadvantages of the technique are also described. In those test situations for which many flowrate combinations are required, or in large area ducts, a tracer flowrate determination requires fewer man-hours than does a conventional traverse-based technique and does not require knowledge of the duct area. 6 refs., 10 figs., 6 tabs.

  2. Measurement of epithermal neutrons by a coherent demodulation technique

    CERN Document Server

    Horiuchi, N; Takahashi, H; Kobayashi, H; Harasawa, S

    2000-01-01

    Epithermal neutrons have been measured using a neutron dosimeter via a coherent demodulation technique. This dosimeter consists of CsI(Tl)-photodiode scintillation detectors, four of which are coupled to neutron-gamma converting foils of various sizes. Neutron-gamma converting foils of In, Au and Co materials were used, each of which has a large capture cross section which peaks in the epithermal neutron energy region. The type of foil was selected according to the material properties that best correspond to the energy of the epithermal neutrons to be measured. In addition, the proposed technique was applied using Au-foils in order to measure the Cd ratio. The validity of the proposed technique was examined using an sup 2 sup 4 sup 1 Am-Be source placed in a testing stack of polyethylene blocks, and the results were compared with the theoretical values calculated by the Monte Carlo calculation. Finally, the dosimeter was applied for measuring epithermal neutrons and the Cd ratio in an experimental beam-tube o...

  3. Noble Gas Measurement and Analysis Technique for Monitoring Reprocessing Facilities

    Energy Technology Data Exchange (ETDEWEB)

    Charlton, William S [Univ. of California, Berkeley, CA (United States)

    1999-09-01

    An environmental monitoring technique using analysis of stable noble gas isotopic ratios on-stack at a reprocessing facility was developed. This technique integrates existing technologies to strengthen safeguards at reprocessing facilities. The isotopic ratios are measured using a mass spectrometry system and are compared to a database of calculated isotopic ratios using a Bayesian data analysis method to determine specific fuel parameters (e.g., burnup, fuel type, fuel age, etc.). These inferred parameters can be used by investigators to verify operator declarations. A user-friendly software application (named NOVA) was developed for the application of this technique. NOVA included a Visual Basic user interface coupling a Bayesian data analysis procedure to a reactor physics database (calculated using the Monteburns 3.01 code system). The integrated system (mass spectrometry, reactor modeling, and data analysis) was validated using on-stack measurements during the reprocessing of target fuel from a U.S. production reactor and gas samples from the processing of EBR-II fast breeder reactor driver fuel. These measurements led to an inferred burnup that matched the declared burnup with sufficient accuracy and consistency for most safeguards applications. The NOVA code was also tested using numerous light water reactor measurements from the literature. NOVA was capable of accurately determining spent fuel type, burnup, and fuel age for these experimental results. Work should continue to demonstrate the robustness of this system for production, power, and research reactor fuels.

  4. Objective techniques for psychological assessment, phase 2. [techniques for measuring human performance during space flight stress

    Science.gov (United States)

    Wortz, E. C.; Saur, A. J.; Nowlis, D. P.; Kendall, M. P.

    1974-01-01

    Results are presented of an initial experiment in a research program designed to develop objective techniques for psychological assessment of individuals and groups participating in long-duration space flights. Specifically examined is the rationale for utilizing measures of attention as an objective assessment technique. Subjects participating in the experiment performed various tasks (eg, playing matrix games which appeared on a display screen along with auditory stimuli). The psychophysiological reactions of the subjects were measured and are given. Previous research of various performance and psychophysiological methods of measuring attention is also discussed. The experiment design (independent and dependent variables) and apparatus (computers and display devices) are described and shown. Conclusions and recommendations are presented.

  5. A digital coincidence measurement system using FPGA techniques

    Energy Technology Data Exchange (ETDEWEB)

    Zhu Fengming; Hsieh, S.C.; Yen, W.W. [Department of Engineering and System Science, National Tsing Hua University, Hsinchu, 30043, Taiwan (China); Chou, H.P., E-mail: hpc@ess.nthu.edu.tw [Department of Engineering and System Science, National Tsing Hua University, Hsinchu, 30043, Taiwan (China)

    2011-10-01

    A field programmable gate array (FPGA) based digital coincidence system has been developed to use with NaI scintillators for field applications. The analog output signal from the photomultiplier anode is directly transferred into digital signals by pulse height for pulse width conversion. The digital signal contains the energy and timing information of the radiation events. The pulse width is then measured by a vernier type of time-to-digital converter (TDC). The timing information of radiation events is recorded and analyzed by a coincidence unit. Both the TDC unit and the coincidence unit are implemented using a commercial available FPGA board. The measured data is then sent to a personal computer for spectrum display. Efficiency as well as energy calibration has been performed. The system showed a timing resolution about 13 ns and an energy resolution of 12% for 0.511 MeV annihilation gammas; it also successfully demonstrated the background rejection ability through coincidence measurement.

  6. Gamma ray densitometry techniques for measuring of volume fractions

    Energy Technology Data Exchange (ETDEWEB)

    Affonso, Renato Raoni Werneck; Silva, Ademir Xavier da; Salgado, Cesar Marques, E-mail: raoniwa@yahoo.com.br, E-mail: ademir@nuclear.ufrj.br, E-mail: otero@ien.gov.br [Instituto de Engenharia Nuclear (IEN/CNEN-RJ), Rio de Janeiro, RJ (Brazil)

    2015-07-01

    Knowledge of the volume fraction in a multiphase flow is of key importance in predicting the performance of many systems and processes. It is therefore an important parameter to characterize such flows. In the context of nuclear techniques, the gamma ray densitometry is promising and this is due to its non-invasive characteristics and very reliable results. It is used in several applications for multiphase flows (water-oil-air), which are employed tools such as: computational fluid dynamics, artificial neural networks and statistical methods of radiation transport, such as the Monte Carlo method. Based on the gamma radiation techniques for measurements of volume fractions, the aim of this paper is to present several techniques developed for this purpose. (author)

  7. A new technique to measure the differential XAFS spectrum

    Science.gov (United States)

    Wu, Min; Zheng, Li-Rong; Chu, Sheng-Qi; Zhou, Ai-Yu; Zhang, Jing; Hu, Tian-Dou

    2016-04-01

    A new technique has been developed for direct measurement of the differential X-ray absorption fine structure (XAFS) spectrum by the energy-modulation method. To acquire the energy-oscillating incident X-ray beam, a piezoelectric actuator is used to control the double-crystal monochromator. A logarithmic converter circuit and a lock-in amplifier are used to extract the modulated signals. The normal and differential XAFS spectra of the Mn K-edge of Li2MnO3 have been collected. The X-ray-absorption near-edge-structure (XANES) spectra verify that the signal-to-noise ratio has been greatly improved by the new technique, and the extended X-ray absorption fine structure (EXAFS) spectra demonstrate that this new technique can efficiently enhance the signals of the backscattering atoms. Supported by NSFC (11175202)

  8. Measurements of Contaminant Dispersion in ventilated Rooms by a Passive Tracer Gas Technique

    DEFF Research Database (Denmark)

    Heiselberg, Per; Bergsøe, Niels Christian

    During recent years the interest in the passive tracer gas technique has grown rapidly. The method has mainly been used in the field for measurements of air infiltration rates in buildings. This paper describes measurements of the contaminant dispersion in a ventilated room using a passive tracer...... gas technique and the results are compared with the results from a conventional method. Vertical profiles of concentration in the middle of the room have been measured at different ventilation air flow rates and different locations of the tracer gas source. The results showed good correspondence...... between the methods within an accuracy of ± 10- 15% in large parts of the room. In regions close to the tracer gas sources the differences were larger. The results gave at the same time recommendations for the use of the passive tracer gas technique for measurements of the air infiltration rates...

  9. Fourier transform approach in modulation technique of experimental measurements.

    Science.gov (United States)

    Khazimullin, M V; Lebedev, Yu A

    2010-04-01

    An application of Fourier transform approach in modulation technique of experimental studies is considered. This method has obvious advantages compared with traditional lock-in amplifiers technique--simple experimental setup, a quickly available information on all the required harmonics, high speed of data processing using fast Fourier transform algorithm. A computationally simple, fast and accurate Fourier coefficients interpolation (FCI) method has been implemented to obtain a useful information from harmonics of a multimode signal. Our analysis shows that in this case FCI method has a systematical error (bias) of a signal parameters estimation, which became essential for the short data sets. Hence, a new differential Fourier coefficients interpolation (DFCI) method has been suggested, which is less sensitive to a presence of several modes in a signal. The analysis has been confirmed by simulations and measurements of a quartz wedge birefringence by means of the photoelastic modulator. The obtained bias, noise level, and measuring speed are comparable and even better than in lock-in amplifier technique. Moreover, presented DFCI method is expected to be promised candidate for using in actively developing imaging systems based on the modulation technique requiring fast digital signal processing of large data sets.

  10. Technique for Performing Dielectric Property Measurements at Microwave Frequencies

    Science.gov (United States)

    Barmatz, Martin B.; Jackson, Henry W.

    2010-01-01

    A paper discusses the need to perform accurate dielectric property measurements on larger sized samples, particularly liquids at microwave frequencies. These types of measurements cannot be obtained using conventional cavity perturbation methods, particularly for liquids or powdered or granulated solids that require a surrounding container. To solve this problem, a model has been developed for the resonant frequency and quality factor of a cylindrical microwave cavity containing concentric cylindrical samples. This model can then be inverted to obtain the real and imaginary dielectric constants of the material of interest. This approach is based on using exact solutions to Maxwell s equations for the resonant properties of a cylindrical microwave cavity and also using the effective electrical conductivity of the cavity walls that is estimated from the measured empty cavity quality factor. This new approach calculates the complex resonant frequency and associated electromagnetic fields for a cylindrical microwave cavity with lossy walls that is loaded with concentric, axially aligned, lossy dielectric cylindrical samples. In this approach, the calculated complex resonant frequency, consisting of real and imaginary parts, is related to the experimentally measured quantities. Because this approach uses Maxwell's equations to determine the perturbed electromagnetic fields in the cavity with the material(s) inserted, one can calculate the expected wall losses using the fields for the loaded cavity rather than just depending on the value of the fields obtained from the empty cavity quality factor. These additional calculations provide a more accurate determination of the complex dielectric constant of the material being studied. The improved approach will be particularly important when working with larger samples or samples with larger dielectric constants that will further perturb the cavity electromagnetic fields. Also, this approach enables the ability to have a

  11. 3D Distance Fields: A Survey of Techniques and Applications

    DEFF Research Database (Denmark)

    Jones, Mark; Bærentzen, Jakob Andreas; Sramek, Milos

    2006-01-01

    A distance field is a representation where at each point within the field we know the distance from that point to the closest point on any object within the domain. In addition to distance, other properties may be derived from the distance field, such as the direction to the surface, and when the...... simple are they to implement? - What is the complexity and run-time of such methods?...

  12. A new measuring technique of soil thermal inertia

    Institute of Scientific and Technical Information of China (English)

    2000-01-01

    Thermal inertia is the function of substance density,heat capacity and heat diffusivity,and is an important parameter for researching the process of surface heat balance using remote sensing technique.In this paper,using soil heat plates,infrared thermometer,data logger and other instruments,by man-controlled changing the solar radiation status on the soil samples,the authors gave a new method to measure soil thermal inertia.Using the continuously surveying data of soil heat flux and infrared radiation temperature,thermal inertia can be calculated easily.Based on the thermal inertia calculation of three soil samples with different water content,good results were abtained by the authors,so this method is feasible.Meanwhile,this measuring technique is also a new attempt.

  13. A new measuring technique of soil thermal inertia

    Institute of Scientific and Technical Information of China (English)

    孙晓敏; 朱治林; 唐新斋; 苏红波; 张仁华

    2000-01-01

    Thermal inertia is the function of substance density, heat capacity and heat diffusivity, and is an important parameter for researching the process of surface heat balance using remote sensing technique. In this paper, using soil heat plates, infrared thermometer, data logger and other instruments, by man-controlled changing the solar radiation status on the soil samples, the authors gave a new method to measure soil thermal inertia. Using the continuously surveying data of soil heat flux and infrared radiation temperature, thermal inertia can be calculated easily. Based on the thermal inertia calculation of three soil samples with different water content, good results were abtained by the authors, so this method is feasible. Meanwhile, this measuring technique is also a new attempt.

  14. Verification of long-term load measurement technique

    DEFF Research Database (Denmark)

    Schmidt Paulsen, Uwe

    The present report is the final effort of tasks carried out under UPWIND WP1B2 transmission and conversion, which describes: 1) results and recommendations developed in the course of developing the long-term load measurement technique 2) the hardware details, type of sensors and location, data...... storage and 3) data analysis technique to verify design load assumptions. The work is carried out under Contract no 019945 (SES6) "UPWIND" within the European Commission The interaction between the mechanical and electrical generator subsystems is described rudimentarily, based primarily on HAWC2...... simulations below stall of the mechanical system with simple generator and gearbox systems. The electrical system simulations were not carried out as intended in DOW[2], but indications of the conditions for establishing the interaction have been described by measurements and by argument, that this might have...

  15. APPLICATION OF NOVEL NEUTRON CORRELATION TECHNIQUES TO NUCLEAR MATERIAL MEASUREMENTS

    Energy Technology Data Exchange (ETDEWEB)

    Sale, K

    2006-06-09

    Confirmation of the fissile mass of a system containing plutonium can be done using neutron multiplicity techniques. This can be accomplished with a detector system that is smaller and less costly than a standard neutron multiplicity counter (NMC). Also the fissile mass of a uranium containing system can be confirmed by passive means. Recent work at Lawrence Livermore National Laboratory has demonstrated that simple slab neutron detectors and a novel approach to data acquisition and analysis can be used to make an accurate measurement of the mass of fissile materials. Purely passive measurement of kilogram quantities of highly enriched uranium (HEU) have also been shown to be feasible. In this paper we discuss calculational tools for assessing the application of these techniques to fissile material transparency regimes. The tools required to adequately model the correlations and their application will be discussed.

  16. 3D interferometric shape measurement technique using coherent fiber bundles

    Science.gov (United States)

    Zhang, Hao; Kuschmierz, Robert; Czarske, Jürgen

    2017-06-01

    In-situ 3-D shape measurements with submicron shape uncertainty of fast rotating objects in a cutting lathe are expected, which can be achieved by simultaneous distance and velocity measurements. Conventional tactile methods, coordinate measurement machines, only support ex-situ measurements. Optical measurement techniques such as triangulation and conoscopic holography offer only the distance, so that the absolute diameter cannot be retrieved directly. In comparison, laser Doppler distance sensors (P-LDD sensor) enable simultaneous and in-situ distance and velocity measurements for monitoring the cutting process in a lathe. In order to achieve shape measurement uncertainties below 1 μm, a P-LDD sensor with a dual camera based scattered light detection has been investigated. Coherent fiber bundles (CFB) are employed to forward the scattered light towards cameras. This enables a compact and passive sensor head in the future. Compared with a photo detector based sensor, the dual camera based sensor allows to decrease the measurement uncertainty by the order of one magnitude. As a result, the total shape uncertainty of absolute 3-D shape measurements can be reduced to about 100 nm.

  17. A comprehensive method of estimating electric fields from vector magnetic field and Doppler measurements

    Energy Technology Data Exchange (ETDEWEB)

    Kazachenko, Maria D.; Fisher, George H.; Welsch, Brian T., E-mail: kazachenko@ssl.berkeley.edu [Space Sciences Laboratory, UC Berkeley, CA 94720 (United States)

    2014-11-01

    Photospheric electric fields, estimated from sequences of vector magnetic field and Doppler measurements, can be used to estimate the flux of magnetic energy (the Poynting flux) into the corona and as time-dependent boundary conditions for dynamic models of the coronal magnetic field. We have modified and extended an existing method to estimate photospheric electric fields that combines a poloidal-toroidal decomposition (PTD) of the evolving magnetic field vector with Doppler and horizontal plasma velocities. Our current, more comprehensive method, which we dub the 'PTD-Doppler-FLCT Ideal' (PDFI) technique, can now incorporate Doppler velocities from non-normal viewing angles. It uses the FISHPACK software package to solve several two-dimensional Poisson equations, a faster and more robust approach than our previous implementations. Here, we describe systematic, quantitative tests of the accuracy and robustness of the PDFI technique using synthetic data from anelastic MHD (ANMHD) simulations, which have been used in similar tests in the past. We find that the PDFI method has less than 1% error in the total Poynting flux and a 10% error in the helicity flux rate at a normal viewing angle (θ = 0) and less than 25% and 10% errors, respectively, at large viewing angles (θ < 60°). We compare our results with other inversion methods at zero viewing angle and find that our method's estimates of the fluxes of magnetic energy and helicity are comparable to or more accurate than other methods. We also discuss the limitations of the PDFI method and its uncertainties.

  18. Measurement Techniques for Electrothermal-Chemical Gun Diagnostics

    Science.gov (United States)

    1993-12-01

    conductors of a circuit ( Askeland 1985). This technique has been successfully applied to other experimental work including the pressure measurements made in...Fe2O4 ( Askeland 1985). Ferrites are implemented by wrapping the power cords and coaxial data lines of all electronics equipment tightly for several... Askeland , D. R. The Sciece and Engineering of Materials. Prindle, Weber, and Schmidt, 1985. Burden. H. S., and D. D. Shear. "Transient Noise in Electronic

  19. PHASE GRADIENT METHOD OF MAGNETIC FIELD MEASUREMENTS IN ELECTRIC VEHICLES

    Directory of Open Access Journals (Sweden)

    N. G. Ptitsyna

    2013-01-01

    Full Text Available Operation of electric and hybrid vehicles demands real time magnetic field control, for instance, for fire and electromagnetic safety. The article deals with a method of magnetic field measurements onboard electric cars taking into account peculiar features of these fields. The method is based on differential methods of measurements, and minimizes the quantity of magnetic sensors.

  20. Applications of Effective Field Theory Techniques to Jet Physics

    Science.gov (United States)

    Freedman, Simon M.

    In this thesis we study jet production at large energies from leptonic collisions. We use the framework of effective theories of Quantum Chromodynamics (QCD) to examine the properties of jets and systematically improve calculations. We first develop a new formulation of soft-collinear effective theory (SCET), the appropriate effective theory for jets. In this formulation, soft and collinear degrees of freedom are described using QCD fields that interact with each other through light-like Wilson lines in external currents. This formulation gives a more intuitive picture of jet processes than the traditional formulation of SCET. In particular, we show how the decoupling of soft and collinear degrees of freedom that occurs at leading order in power counting is explicit to next-to-leading order and likely beyond. We then use this formulation to write the thrust rate in a factorized form at next-to-leading order in the thrust parameter. The rate involves an incomplete sum over final states due to phase space cuts that is enforced by a measurement operator. Subleading corrections require matching onto not only the next-to-next-to leading order SCET operators, but also matching onto subleading measurement operators. We derive the appropriate hard, jet, and soft functions and show they reproduce the expected subleading thrust rate. Next, we renormalize the next-to-leading order dijet operators used for the subleading thrust rate. Constraints on matching coefficients from current conservation and reparametrization invariance are shown. We also discuss the subtleties involved in regulating the infrared divergences of the individual loop diagrams in order to extract the ultraviolet divergences. The results can be used to increase the theoretical precision of the thrust rate. Finally, we study the (exclusive) k⊥ and C/A jet algorithms in SCET. Regularizing the virtualities and rapidities of the individual graphs, we are able to write the O(alpha s) dijet cross section as the

  1. Experimental Methods Using Photogrammetric Techniques for Parachute Canopy Shape Measurements

    Science.gov (United States)

    Jones, Thomas W.; Downey, James M.; Lunsford, Charles B.; Desabrais, Kenneth J.; Noetscher, Gregory

    2007-01-01

    NASA Langley Research Center in partnership with the U.S. Army Natick Soldier Center has collaborated on the development of a payload instrumentation package to record the physical parameters observed during parachute air drop tests. The instrumentation package records a variety of parameters including canopy shape, suspension line loads, payload 3-axis acceleration, and payload velocity. This report discusses the instrumentation design and development process, as well as the photogrammetric measurement technique used to provide shape measurements. The scaled model tests were conducted in the NASA Glenn Plum Brook Space Propulsion Facility, OH.

  2. Vibration frequency measurement using a local multithreshold technique.

    Science.gov (United States)

    Ferrer, Belen; Espinosa, Julian; Roig, Ana B; Perez, J; Mas, D

    2013-11-01

    In this paper, we demonstrate the use of a video camera for measuring the frequency of small-amplitude vibration movements. The method is based on image acquisition and multilevel thresholding and it only requires a video camera with high enough acquisition rate, not being necessary the use of targets or auxiliary laser beams. Our proposal is accurate and robust. We demonstrate the technique with a pocket camera recording low-resolution videos with AVI-JPEG compression and measuring different objects that vibrate in parallel or perpendicular direction to the optical sensor. Despite the low resolution and the noise, we are able to measure the main vibration modes of a tuning fork, a loudspeaker and a bridge. Results are successfully compared with design parameters and measurements with alternative devices.

  3. Data fusion techniques for incomplete measurement of trajectory

    Institute of Scientific and Technical Information of China (English)

    2001-01-01

    This paper focuses on data processing for incomplete measurementof trajectory (IMT) in aerospace mea- surement and control. The IMT means that the principal equipment loses the measured data during some intervals so that trajectory parameters (position, velocity, etc.) cannot be determined independently. Based on a joint model for trajectory estimation with reduced parameter, a fusion way is put forth by making full use of measured data from auxiliary equipment with lower precision. In the superposition intervals of measurement between principal and auxiliary equipment, the technique of diagnosing and estimating system errors is applied to improving the estimate precision of trajectory parameters (TP) and determining the precision after data fusion. In practical test, this method operates so successfully that it can not only provide complete TP but improve their precision remarkably. Meanwhile, this way is also applicable to other problems of incomplete measurement.

  4. A new distensibility technique to measure sphincter of Oddi function

    DEFF Research Database (Denmark)

    Kunwald, Peter; Drewes, Asbjørn Mohr; Kjær, D.;

    2010-01-01

    . Methods The SO probe was constructed to measure eight cross-sectional areas (CSA) along a length of 25 mm inside a saline-filled bag. To validate the technique for profiling the SO, six perspex cylinders with different CSAs were measured nine times to assess reproducibility and accuracy. Key Results...... probe and validating it for measurements in the SO. In order to get a better physiological understanding of the SO the aims were to show the sphincter profile in vivo and motility patterns of SO in pilot studies using volunteers that were experiencing biliary type pain but had normal SO manometry...... Reproducibility and accuracy for these measurements were good. The probe performed well in bench tests and was therefore tested in four humans. The data indicated that it was possible to make distensions in the human SO and that a geometric sphincter profile could be obtained. Conclusions & Inferences The probe...

  5. Application of the planar-scanning technique to the near-field dosimetry of millimeter-wave radiators.

    Science.gov (United States)

    Zhao, Jianxun; Lu, Hongmin; Deng, Jun

    2015-02-01

    The planar-scanning technique was applied to the experimental measurement of the electric field and power flux density (PFD) in the exposure area close to the millimeter-wave (MMW) radiator. In the near-field region, the field and PFD were calculated from the plane-wave spectrum of the field sampled on a scan plane far from the radiator. The measurement resolution was improved by reducing the spatial interval between the field samples to a fraction of half the wavelength and implementing multiple iterations of the fast Fourier transform. With the reference to the results from the numerical calculation, an experimental evaluation of the planar-scanning measurement was made for a 50 GHz radiator. Placing the probe 1 to 3 wavelengths from the aperture of the radiator, the direct measurement gave the near-field data with significant differences from the numerical results. The planar-scanning measurement placed the probe 9 wavelengths away from the aperture and effectively reduced the maximum and averaged differences in the near-field data by 70.6% and 65.5%, respectively. Applied to the dosimetry of an open-ended waveguide and a choke ring antenna for 60 GHz exposure, the technique proved useful to the measurement of the PFD in the near-field exposure area of MMW radiators.

  6. Field of Temperature Measurement by Virtual Instrumentation

    Directory of Open Access Journals (Sweden)

    Libor HARGAŠ

    2009-01-01

    Full Text Available This paper introduces about temperature determination for given dot of picture through image analysis. Heat transfer is the transition of thermal energy from a heated item to a cooler item. Main method of measurement of temperature in image is Pattern Matching, color scale detection and model detection. We can measure temperature dependency at time for selected point of thermo vision images. This measurement gives idea about the heat transfer at time dependences.

  7. 3D Distance Fields: A Survey of Techniques and Applications

    DEFF Research Database (Denmark)

    Jones, Mark; Bærentzen, Jakob Andreas; Sramek, Milos

    2006-01-01

    the distance field is signed, we may also determine if the point is internal or external to objects within the domain. The distance field has been found to be a useful construction within the areas of Computer Vision, Physics and Computer Graphics. This paper serves as a timely exposition of methods...

  8. Velocity field statistics and tessellation techniques : Unbiased estimators of Omega

    NARCIS (Netherlands)

    Van de Weygaert, R; Bernardeau, F; Muller,; Gottlober, S; Mucket, JP; Wambsganss, J

    1998-01-01

    We describe two new - stochastic-geometrical - methods to obtain reliable velocity field statistics from N-body simulations and from any general density and velocity fluctuation field sampled at a discrete set of locations. These methods, the Voronoi tessellation method and Delaunay tessellation met

  9. Measurement of real pulsatile blood flow using X-ray PIV technique with CO2 microbubbles.

    Science.gov (United States)

    Park, Hanwook; Yeom, Eunseop; Seo, Seung-Jun; Lim, Jae-Hong; Lee, Sang-Joon

    2015-03-06

    Synchrotron X-ray imaging technique has been used to investigate biofluid flows in a non-destructive manner. This study aims to investigate the feasibility of the X-ray PIV technique with CO2 microbubbles as flow tracer for measurement of pulsatile blood flows under in vivo conditions. The traceability of CO2 microbubbles in a pulsatile flow was demonstrated through in vitro experiment. A rat extracorporeal bypass loop was used by connecting a tube between the abdominal aorta and jugular vein of a rat to obtain hemodynamic information of actual pulsatile blood flows without changing the hemorheological properties. The decrease in image contrast of the surrounding tissue was also investigated for in vivo applications of the proposed technique. This technique could be used to accurately measure whole velocity field information of real pulsatile blood flows and has strong potential for hemodynamic diagnosis of cardiovascular diseases.

  10. Measurement of the SC magnetic field

    CERN Multimedia

    CERN PhotoLab

    1973-01-01

    The 3.5-metre-arm carrying 100 Hall plates used for the measurmeent of the SC magnetic field. The arm rotates in a horizontal plane, its positioning and the data read-out are controlled by an on-line computer.

  11. Sampling Criterion for EMC Near Field Measurements

    DEFF Research Database (Denmark)

    Franek, Ondrej; Sørensen, Morten; Ebert, Hans

    2012-01-01

    -case representative of a signal trace on a typical printed circuit board. It has been found that the sampling density derived in this way is in fact very similar to that given by the antenna near field sampling theorem, if an error less than 1 dB is required. The principal advantage of the proposed formulation is its...

  12. Improved Tandem Measurement Techniques for Aerosol Particle Analysis

    Science.gov (United States)

    Rawat, Vivek Kumar

    Non-spherical, chemically inhomogeneous (complex) nanoparticles are encountered in a number of natural and engineered environments, including combustion systems (which produces highly non-spherical aggregates), reactors used in gas-phase materials synthesis of doped or multicomponent materials, and in ambient air. These nanoparticles are often highly diverse in size, composition and shape, and hence require determination of property distribution functions for accurate characterization. This thesis focuses on development of tandem mobility-mass measurement techniques coupled with appropriate data inversion routines to facilitate measurement of two dimensional size-mass distribution functions while correcting for the non-idealities of the instruments. Chapter 1 provides the detailed background and motivation for the studies performed in this thesis. In chapter 2, the development of an inversion routine is described which is employed to determine two dimensional size-mass distribution functions from Differential Mobility Analyzer-Aerosol Particle Mass analyzer tandem measurements. Chapter 3 demonstrates the application of the two dimensional distribution function to compute cumulative mass distribution function and also evaluates the validity of this technique by comparing the calculated total mass concentrations to measured values for a variety of aerosols. In Chapter 4, this tandem measurement technique with the inversion routine is employed to analyze colloidal suspensions. Chapter 5 focuses on application of a transverse modulation ion mobility spectrometer coupled with a mass spectrometer to study the effect of vapor dopants on the mobility shifts of sub 2 nm peptide ion clusters. These mobility shifts are then compared to models based on vapor uptake theories. Finally, in Chapter 6, a conclusion of all the studies performed in this thesis is provided and future avenues of research are discussed.

  13. Measurement of the velocity field behind the automotive vent

    Directory of Open Access Journals (Sweden)

    Jedelský Jan

    2012-04-01

    Full Text Available Passenger comfort in a personal vehicle cabin strongly depends on the appropriate function of the cabin ventilation system. Great attention is therefore paid to the effective functioning of the automotive vents. Various techniques can be employed to evaluate the proper formation of the flow behind the ventilation outlet. Constant Temperature Anemometry (CTA was used in our case for accurate measurement of the velocity field and consequent assessment of jet boundaries and jet axis. A novel methodology has been developed for the simulation of realistic conditions when using just a single vent under laboratory conditions instead of the complete vehicle ventilation system. A special technique has also been developed for determination of the terminal inclination angles of vent vanes for the particular vent type, which can be completely closed by the adjustable horizontal vanes. A two wire CTA probe was used for measurement of the actual velocity over predefined planes, which were specified according to smoke visualization. Mean velocities and the turbulence intensity were evaluated on the basis of the obtained data and are presented in a form of charts. Both jet boundary and orientation of the jet for a given setup of the vent are important characteristics of particular vent type. Effectiveness of different vents could be compared using our methodology and hence contribute to development of advanced ventilation system.

  14. Measurement of the velocity field behind the automotive vent

    Science.gov (United States)

    Ležovič, Tomáš; Lízal, František; Jedelský, Jan; Jícha, Miroslav

    2012-04-01

    Passenger comfort in a personal vehicle cabin strongly depends on the appropriate function of the cabin ventilation system. Great attention is therefore paid to the effective functioning of the automotive vents. Various techniques can be employed to evaluate the proper formation of the flow behind the ventilation outlet. Constant Temperature Anemometry (CTA) was used in our case for accurate measurement of the velocity field and consequent assessment of jet boundaries and jet axis. A novel methodology has been developed for the simulation of realistic conditions when using just a single vent under laboratory conditions instead of the complete vehicle ventilation system. A special technique has also been developed for determination of the terminal inclination angles of vent vanes for the particular vent type, which can be completely closed by the adjustable horizontal vanes. A two wire CTA probe was used for measurement of the actual velocity over predefined planes, which were specified according to smoke visualization. Mean velocities and the turbulence intensity were evaluated on the basis of the obtained data and are presented in a form of charts. Both jet boundary and orientation of the jet for a given setup of the vent are important characteristics of particular vent type. Effectiveness of different vents could be compared using our methodology and hence contribute to development of advanced ventilation system.

  15. Stable isotope measurements of evapotranspiration partitioning in a maize field

    Science.gov (United States)

    Hogan, Patrick; Parajka, Juraj; Oismüller, Markus; Strauss, Peter; Heng, Lee; Blöschl, Günter

    2017-04-01

    Evapotranspiration (ET) is one of the most important processes in describing land surface - atmosphere interactions as it connects the energy and water balances. Furthermore knowledge of the individual components of evapotranspiration is important for ecohydrological modelling and agriculture, particularly for irrigation efficiency and crop productivity. In this study, we tested the application of the stable isotope method for evapotranspiration partitioning to a maize crop during the vegetative stage, using sap flow sensors as a comparison technique. Field scale ET was measured using an eddy covariance device and then partitioned using high frequency in-situ measurements of the isotopic signal of the canopy water vapor. The fraction of transpiration (Ft) calculated with the stable isotope method showed good agreement with the sap flow method. High correlation coefficient values were found between the two techniques, indicating the stable isotope method can successfully be applied in maize. The results show the changes in transpiration as a fraction of evapotranspiration after rain events and during the subsequent drying conditions as well as the relationship between transpiration and solar radiation and vapor pressure deficit.

  16. Measuring glioma volumes: A comparison of linear measurement based formulae with the manual image segmentation technique

    Directory of Open Access Journals (Sweden)

    Sanjeev A Sreenivasan

    2016-01-01

    Conclusions: Manual region of interest-based image segmentation is the standard technique for measuring glioma volumes. For routine clinical use, the simple formula v = abc/2 (or the formula for volume of an ellipsoid could be used as alternatives.

  17. Laboratory Measurements of Astrophysical Magnetic Fields

    Science.gov (United States)

    Murphy, C. D.; Miniati, F.; Edwards, M.; Mithen, J.; Bell, A. R.; Constantin, C.; Everson, E.; Schaeffer, D.; Niemann, C.; Ravasio, A.; Brambrink, E.; Benuzzi-Mounaix, A.; Koenig, M.; Gregory, C.; Woolsey, N.; Park, H.-S.; Remington, B.; Ryutov, D.; Bingham, R.; Gargate, L.; Spitkovsky, A.; Gregori, G.

    2010-11-01

    It has been proposed that high Mach number collisionless shocks propagating in an initially unmagnetized plasma play a major role in the magnetization of large scale structures in the Universe. A detailed study of the experimental configuration necessary to scale such environments down to laboratory dimensions will be presented. We will show initial results from preliminary experiments conducted at the Phoenix laser (UCLA) and the LULI laser (Ecole Polytechnique) where collisionless shocks are generated by the expansion of exploding foils driven by energetic laser beams. The time evolution of the magnetic field is probed with induction coils placed at 10 cm from the laser focus. We will discuss various mechanisms of magnetic field generation and compare them with the experimental results.

  18. Radiographic measurements of hallux angles: a review of current techniques.

    Science.gov (United States)

    Srivastava, Subodh; Chockalingam, N; El Fakhri, Tarek

    2010-03-01

    Radiographic angles are commonly used in patients with hallux valgus deformity to assess the severity, plan surgery, assess outcome and compare results. Many different manual methods have been used, but are prone to error. More recently computer-assisted methods using software have become available. To review the different methods that have been used to measure radiographic angles in hallux valgus. A general literature search using relevant key words was undertaken using databases such as Medline, Embase, Cinahl and Cochrane Library. REVIEW FINDINGS AND DISCUSSION: The manual methods used are prone to errors. The reliability can be improved by using standardised radiographic technique and measurement technique using specific reference points. Computer-assisted methods using software, might improve reliability of measurements. Further studies are needed to assess if these methods are easy to use, and to compare different software's that are available. Specifically designed software for the foot might further improve the reliability of radiographic measurements in hallux valgus. Copyright (c) 2009 Elsevier Ltd. All rights reserved.

  19. Entrance surface dose measurements in mammography using thermoluminescence technique

    Energy Technology Data Exchange (ETDEWEB)

    Rivera, T. [Centro de Investigacion en Ciencia Aplicada y Tecnologia Avanzada Unidad Legaria del IPM Av. Legaria 694, 11500 Mexico D.F. (Mexico); Vega C, H.R.; Manzanares A, E [Unidad Academica de Estudios Nucleares, Universidad Autonoma de Zacatecas, Apdo. Postal 336, 98000 Zacatecas (Mexico); Azorin, J. [Universidad Autonoma Metropolitana-lztapalapa, Av. San Rafael Atlixco 186, 09340 Mexico D.F. (Mexico); Gonzalez, P.R. [Instituto Nacional de Investigaciones Nucleares, Carretera Mexico Toluca, 52045 Salazar Estado de Mexico (Mexico)

    2007-07-01

    Full text: Of the various techniques that can be used for personnel dosimetry, thermoluminescence dosimetry (TLD) has emerged as a superior technique due to its manifold advantages over other methods of dose estimation. Various phosphors have been therefore investigated regarding their suitability for dosimetry. In this paper, a dosimetry system based on thermally stimulated luminescence (TSL) from zirconium oxide phosphors embedded in polytetrafluorethylene (ZrO{sub 2}+PTFE) was developed for entrance surface doses (ES) measurements in mammography. Small ZrO{sub 2} pellets of 5 mm in diameter and 0.8 mm in thickness were used. The reproducibility of measurements and linearity of ZrO{sub 2} were also studied. The results were compared with those obtained from LiF:Mg,Cu,P usually used for the determination of absorbed dose in mammography. Measurements both per unit air kerma and In vivo were performed using a mammography unit model DMR (General Electric). The results showed that ZrO{sub 2} TLDs can be used for the same X-ray dosimetry applications as LiF:Mg,Cu,P, with each type having the disadvantage of a response dependent on energy, particularly at low energies. These results indicate a considerable potential for use in routine control and In vivo ES measurements in mammography. (Author)

  20. Measurement Methods in the field of benchmarking

    Directory of Open Access Journals (Sweden)

    István Szűts

    2004-05-01

    Full Text Available In benchmarking we often come across with parameters being difficultto measure while executing comparisons or analyzing performance, yet they haveto be compared and measured so as to be able to choose the best practices. Thesituation is similar in the case of complex, multidimensional evaluation as well,when the relative importance and order of different dimensions, parameters to beevaluated have to be determined or when the range of similar performanceindicators have to be decreased with regard to simpler comparisons. In suchcases we can use the ordinal or interval scales of measurement elaborated by S.S.Stevens.

  1. Measuring Propagation Speed of Coulomb Fields

    OpenAIRE

    De Sangro, R.; Finocchiaro, G.; Patteri, P.; Piccolo, M.; Pizzella, G.

    2012-01-01

    The problem of gravity propagation has been subject of discussion for quite a long time: Newton, Laplace and, in relatively more modern times, Eddington pointed out that, if gravity propagated with finite velocity, planets motion around the sun would become unstable due to a torque originating from time lag of the gravitational interactions. Such an odd behavior can be found also in electromagnetism, when one computes the propagation of the electric fields generated by a set of uniformly movi...

  2. Gravity field, geoid and ocean surface by space techniques

    Science.gov (United States)

    Anderle, R. J.

    1978-01-01

    Knowledge of the earth's gravity field continued to increase during the last four years. Altimetry data from the GEOS-3 satellite has provided the geoid over most of the ocean to an accuracy of about one meter. Increasing amounts of laser data has permitted the solution for 566 terms in the gravity field with which orbits of the GEOS-3 satellite have been computed to an accuracy of about one to two meters. The combination of satellite tracking data, altimetry and gravimetry has yielded a solution for 1360 terms in the earth's gravity field. A number of problems remain to be solved to increase the accuracy of the gravity field determination. New satellite systems would provide gravity data in unsurveyed areas and correction for topographic features of the ocean and improved computational procedures together with a more extensive laser network will considerably improve the accuracy of the results.

  3. Flowing dusty plasma experiments: generation of flow and measurement techniques

    Science.gov (United States)

    Jaiswal, S.; Bandyopadhyay, P.; Sen, A.

    2016-12-01

    A variety of experimental techniques for the generation of subsonic/supersonic dust fluid flows and means of measuring such flow velocities are presented. The experiments have been carried out in a \\Pi -shaped dusty plasma experimental device with micron size kaolin/melamine formaldehyde particles embedded in a background of argon plasma created by a direct current glow discharge. A stationary dust cloud is formed over the cathode region by precisely balancing the pumping speed and gas flow rate. A flow of dust particles/fluid is generated by additional gas injection from a single or dual locations or by altering the dust confining potential. The flow velocity is then estimated by three different techniques, namely, by super particle identification code, particle image velocimetry analysis and the excitation of dust acoustic waves. The results obtained from these three different techniques along with their merits and demerits are discussed. An estimation of the neutral drag force responsible for the generation as well as the attenuation of the dust fluid flow is made. These techniques can be usefully employed in laboratory devices to investigate linear and non-linear collective excitations in a flowing dusty plasma.

  4. Comparison of stress-measuring techniques at the DNA-UTP site, Rodgers Hollow, Kentucky

    Energy Technology Data Exchange (ETDEWEB)

    Finley, R.E.

    1994-12-01

    The Defense Nuclear Agency (DNA) is developing explosives technology through its Underground Technology Program (UTP). Sandia National Laboratories (SNL) has supported the DNA by conducting research to characterize the in situ stress and rock mass deformability at one of the UTP underground sites at Rodgers Hollow, near Louisville, Kentucky on the Fort Knox Military Reservation. The purpose of SNL`s testing was to determine the in situ stress using three different measurement techniques and, if possible, to estimate the rock mass modulus near the underground opening. The three stress-measuring techniques are (1) borehole deformation measurements using overcoring, (2) Anelastic Strain Recovery (ASR) complemented by laboratory ultrasonic and mechanical properties testing, and (3) the in situ flatjack technique using cancellation pressure. Rock mass modulus around the underground opening was estimated using the load deformation history of the flatjack and surrounding rock. Borehole deformation measurements using the overcoring technique probably represent the most reliable method for in situ stress determination in boreholes up to 50 ft (15 m) deep in competent rock around an isolated excavation. The technique is used extensively by the tunneling and mining industries. The ASR technique is also a core-based technique and is used in the petroleum and natural gas industries for characterization of in situ stress from deep boreholes. The flatjack technique has also been used in the tunneling and mining industries, and until recently has been limited to measurement of the stress immediately around the excavation. Results from the flatjack technique must be further analyzed to calculate the in situ stress in the far field.

  5. Laboratory technique for quantitative thermal emissivity measurements of geological samples

    Indian Academy of Sciences (India)

    George Mathew; Archana Nair; T K Gundu Rao; Kanchan Pande

    2009-08-01

    Thermal infrared spectroscopy is a powerful technique for the compositional analysis of geological materials. The spectral feature in the mid-IR region is diagnostic of the mineralogy and spectral signatures of mixtures of minerals that add linearly, and therefore, can be used as an important tool to determine the mineralogy of rocks in the laboratory and remotely for planetary exploration. The greatest challenge in the emission measurement lies in the measurement of the weak thermal photons emitted from geological materials in a laboratory setup, and accurately records the temperature of the rock sample. The present work pertains to the details of a new Thermal Emission Spectrometer (TES) laboratory that has been developed under the ISRO Planetary Science and Exploration (PLANEX) programme, for emission related mineralogical investigations of planetary surfaces. The focus of the paper is on the acquisition and calibration technique for obtaining emissivity, and the deconvolution procedure to obtain the modal abundances of the thermal emission spectra in the range of 6–25 m using Fourier Transform Infrared (FTIR) spectroscopy. The basic technique is adopted from the work of Ruff et al (1997). This laboratory at the Department of Earth Sciences, IIT-Bombay is currently developing pure end mineral library of mineral particulates (> 65 m), and adding new end members to the existing ASU spectral library. The paper argues the need for considering Lunar Orbiter Thermal Emission Spectrometer (LOTES) for future Indian Moon mission programme (Chandrayan-II) to determine evidences of varied lithologies on the lunar surface.

  6. Hybrid PIV-PTV technique for measuring blood flow in rat mesenteric vessels.

    Science.gov (United States)

    Ha, Hojin; Nam, Kweon-Ho; Lee, Sang Joon

    2012-11-01

    The micro-particle tracking velocimetry (μ-PTV) technique is used to obtain the velocity fields of blood flow in the microvasculature under in vivo conditions because it can provide the blood velocity distribution in microvessels with high spatial resolution. The in vivo μ-PTV technique usually requires a few to tens of seconds to obtain a whole velocity profile across the vessel diameter because of the limited number density of tracer particles under in vivo conditions. Thus, the μ-PTV technique alone is limited in measuring unsteady blood flows that fluctuate irregularly due to the heart beating and muscle movement in surrounding tissues. In this study, a new hybrid PIV-PTV technique was established by combining PTV and particle image velocimetry (PIV) techniques to resolve the drawbacks of the μ-PTV method in measuring blood flow in microvessels under in vivo conditions. Images of red blood cells (RBCs) and fluorescent particles in rat mesenteric vessels were obtained simultaneously. Temporal variations of the centerline blood velocity were monitored using a fast Fourier transform-based cross-correlation PIV method. The fluorescence particle images were analyzed using the μ-PTV technique to extract the spatial distribution of the velocity vectors. Data from the μ-PTV and PIV methods were combined to obtain a better estimate of the velocity profile in actual blood flow. This technique will be useful in investigating hemodynamics in microcirculation by measuring unsteady irregular blood flows more accurately.

  7. A Comparison of Stellar Elemental Abundance Techniques and Measurements

    CERN Document Server

    Hinkel, Natalie R; Pagano, Michael D; Desch, Steven J; Anbar, Ariel D; Adibekyan, Vardan; Blanco-Cuaresma, Sergi; Carlberg, Joleen K; Mena, Elisa Delgado; Liu, Fan; Nordlander, Thomas; Sousa, Sergio G; Korn, Andreas; Gruyters, Pieter; Heiter, Ulrike; Jofre, Paula; Santos, Nuno C; Soubiran, Caroline

    2016-01-01

    Stellar elemental abundances are important for understanding the fundamental properties of a star or stellar group, such as age and evolutionary history, as well as the composition of an orbiting planet. However, as abundance measurement techniques have progressed, there has been little standardization between individual methods and their comparisons. As a result, different stellar abundance procedures determine measurements that vary beyond quoted error for the same elements within the same stars (Hinkel et al. 2014). The purpose of this paper is to better understand the systematic variations between methods and offer recommendations for producing more accurate results in the future. We have invited a number of participants from around the world (Australia, Portugal, Sweden, Switzerland, and USA) to calculate ten element abundances (C, O, Na, Mg, Al, Si, Fe, Ni, Ba, and Eu) using the same stellar spectra for four stars (HD361, HD10700, HD121504, HD202206). Each group produced measurements for each of the sta...

  8. ONLINE GRINDING WHEEL WEAR COMPENSATION BY IMAGE BASED MEASURING TECHNIQUES

    Institute of Scientific and Technical Information of China (English)

    WAN Daping; HU Dejin; WU Qi; ZHANG Yonghong

    2006-01-01

    Automatic compensation of grinding wheel wear in dry grinding is accomplished by an image based online measurement method. A kind of PC-based charge-coupled device image recognition system is schemed out, which detects the topography changes of the grinding wheel surface. Profile data, which corresponds to the wear and the topography, is measured by using a digital image processing method. The grinding wheel wear is evaluated by analyzing the position deviation of the grinding wheel edge. The online wear compensation is achieved according to the measure results. The precise detection and automatic compensation system is integrated into an open structure CNC curve grinding machine. A practical application is carried out to fulfil the precision curve grinding. The experimental results confirm the benefits of the proposed techniques, and the online detection accuracy is less than 5 μm. The grinding machine provides higher precision according to the in-process grinding wheel error compensation.

  9. Velocity of detonation (VOD measurement techniques - practical approach

    Directory of Open Access Journals (Sweden)

    Aruna Dhanraj Tete

    2013-06-01

    Full Text Available Velocity of Detonation (VOD is an important measure characteristics parameter of explosive material. The performance of explosive invariably depends on the velocity of detonation. The power/ strength of explosive to cause fragmentation of the solid structure determine the efficiency of the Blast performed. It is an established fact that measuring velocity of detonation gives a good indication of the strength and hence the performance of the explosive. In this survey various VOD measurement techniques such as electric, nonelectric and fibre optic have been discussed. To aid the discussion some commercially available VOD meter comparison are also presented. After review of the existing units available commercially and study of their respective merits and demerits, feature of an ideal system is proposed. 

  10. Computerized tomography technique for reconstruction of obstructed temperature field in infrared thermography

    Science.gov (United States)

    Sham, F. C.; Huang, Y. H.; Liu, L.; Chen, Y. S.; Hung, Y. Y.; Lo, T. Y.

    2010-01-01

    Infrared thermography is a rapid, non-invasive and full-field technique for non-destructive testing and evaluation (NDT&E). With all the achievements on IR instrumentation and image processing techniques attained, it has been extended far beyond simple hot-spot detection and becomes one of the most promising NDT&E techniques in the last decades. It has achieved increasing acceptance in different sectors include medical imaging, manufacturing component fault detection and buildings diagnostic. However, one limitation of IR thermography is that the testing results are greatly affected by object surface emissivity. Surface with various emissivities may lead to difficult discrimination between area of defect and area with different emissivity. Therefore, many studies have been carried out on eliminating emissivity, for example, the time derivative approach, lock-in processing and differential contrast measurements. In these methods, sequence of themo-data/images are recorded and being processed in order to eliminate differences of emissivity. Another problem of IR thermography is that any obstruction may limit stimulations and imaging which leads to the observation of unclear defect image. To solve this problem, this paper proposes an algorithm based on the principle of computerized tomography which permits the reconstruction of unavailable/partially available temperature distribution of the affected area using the measured surrounding temperature field. In the process, a set of imaginary rays are projected from many different directions across the area. For each ray, integration of the temperature derivatives along the ray is equals to the temperature difference between the boundary points intercepted by the ray. Therefore, a set of linear equations can be established by considering the multiple rays. Each equation expresses the unknown temperature derivatives in the affected area in terms of the measured boundary temperature data. Solution of the set of simultaneous

  11. Analysis of the measurement field of the optical klystron

    Institute of Scientific and Technical Information of China (English)

    2000-01-01

    The measured fields of the optical klystron in NSRL (National Sychrotron Radiation Laboratory) are given, including the distribution on the axis, and the integrated field distribution. The harmonic magnet field and the spectra of the spontaneous emission are analyzed, and the multiple field is presented by fitting the diagram. The influence of the integrated field on the close orbit of the beam and on the operation parameters of the storage ring, and the compensation in the experiment are also discussed.

  12. Galois Field Based Very Fast and Compact Error Correcting Technique

    Directory of Open Access Journals (Sweden)

    Alin Sindhu.A,

    2014-01-01

    Full Text Available As the technology is improving the memory devices are becoming larger, so powerful error correction codes are needed. Error correction codes are commonly used to protect memories from soft errors, which change the logical value of memory cells without damaging the circuit. These codes can correct a large number of errors, but generally require complex decoders. In order to avoid this decoding complexity, in this project it uses Euclidean geometry LDPC codes with one step majority decoding technique. This method detects words having error in the first iteration of the majority logic decoding process and reduces the decoding time by stopping the decoding process when no errors are detected as well as reduces the memory access time. And the result obtained through this technique also proves that it is an effective and compact error correcting technique.

  13. Flow field measurements in the cell culture unit

    Science.gov (United States)

    Walker, Stephen; Wilder, Mike; Dimanlig, Arsenio; Jagger, Justin; Searby, Nancy

    2002-01-01

    The cell culture unit (CCU) is being designed to support cell growth for long-duration life science experiments on the International Space Station (ISS). The CCU is a perfused loop system that provides a fluid environment for controlled cell growth experiments within cell specimen chambers (CSCs), and is intended to accommodate diverse cell specimen types. Many of the functional requirements depend on the fluid flow field within the CSC (e.g., feeding and gas management). A design goal of the CCU is to match, within experimental limits, all environmental conditions, other than the effects of gravity on the cells, whether the hardware is in microgravity ( micro g), normal Earth gravity, or up to 2g on the ISS centrifuge. In order to achieve this goal, two steps are being taken. The first step is to characterize the environmental conditions of current 1g cell biology experiments being performed in laboratories using ground-based hardware. The second step is to ensure that the design of the CCU allows the fluid flow conditions found in 1g to be replicated from microgravity up to 2g. The techniques that are being used to take these steps include flow visualization, particle image velocimetry (PIV), and computational fluid dynamics (CFD). Flow visualization using the injection of dye has been used to gain a global perspective of the characteristics of the CSC flow field. To characterize laboratory cell culture conditions, PIV is being used to determine the flow field parameters of cell suspension cultures grown in Erlenmeyer flasks on orbital shakers. These measured parameters will be compared to PIV measurements in the CSCs to ensure that the flow field that cells encounter in CSCs is within the bounds determined for typical laboratory experiments. Using CFD, a detailed simulation is being developed to predict the flow field within the CSC for a wide variety of flow conditions, including microgravity environments. Results from all these measurements and analyses of the

  14. Application of Sensing Techniques to Cellular Force Measurement

    Directory of Open Access Journals (Sweden)

    James H.-C. Wang

    2010-11-01

    Full Text Available Cell traction forces (CTFs are the forces produced by cells and exerted on extracellular matrix or an underlying substrate. CTFs function to maintain cell shape, enable cell migration, and generate and detect mechanical signals. As such, they play a vital role in many fundamental biological processes, including angiogenesis, inflammation, and wound healing. Therefore, a close examination of CTFs can enable better understanding of the cellular and molecular mechanisms of such processes. To this end, various force-sensing techniques for CTF measurement have been developed over the years. This article will provide a concise review of these sensing techniques and comment on the needs for improved force-sensing technologies for cell mechanics and biology research.

  15. Precise measurement technique for the stable acoustic cavitation bubble

    Institute of Scientific and Technical Information of China (English)

    HUANG Wei; CHEN Weizhong; LIU Yanan; GAO Xianxian; JIANG Lian; XU Junfeng; ZHU Yifei

    2005-01-01

    Based on the periodic oscillation of the stable acoustic cavitation bubble, we present a precise measurement technique for the bubble evolution. This technique comprises the lighting engineering of pulsing laser beam whose phase can be digitally shifted, and the long distance microphotographics. We used a laser, an acousto-optic modulator, a pulse generator, and a long distance microscope. The evolution of a levitated bubble can be directly shown by a series of bubble's images at different phases. Numerical simulation in the framework of the Rayleigh-Plesset bubble dynamics well supported the experimental result, and the ambient radius of the bubble, an important parameter related to the mass of the gas inside the bubble, was obtained at the same time.

  16. Gradio - Earth gravity field measurement on Aristoteles

    Science.gov (United States)

    Pawlak, D.; Meyer, Ph.; Bernard, A.; Touboul, P.

    1991-10-01

    The design and operation of Gradio, the instrument that was specifically designed for precise gradiometry measurements during the Aristoteles mission, are described. The Gradio is based on simultaneous measurements by four three-axis ultrasensitive accelerometers performed in several locations on a rigid stable structure, called gradio plate, which are then used to compute g gradients. The operational phase of Gradio will last 6 months; the orbit will be circular, near polar, and heliosynchronous, at an altitude of 200 km. It is estimated that Gradio will measure the two main components T(yy) and T(zz) of the gravity gradient tensor in the (0.005, 0.125) Hz frequency bandwidth with an accuracy of 0.01 E.U.

  17. Damage detection technique by measuring laser-based mechanical impedance

    Energy Technology Data Exchange (ETDEWEB)

    Lee, Hyeonseok; Sohn, Hoon [Department of Civil and Environmental Engineering, Korea Advanced Institute of Science and Technology (Daehak-ro 291, Yuseong-gu, Daejeon 305-701) (Korea, Republic of)

    2014-02-18

    This study proposes a method for measurement of mechanical impedance using noncontact laser ultrasound. The measurement of mechanical impedance has been of great interest in nondestructive testing (NDT) or structural health monitoring (SHM) since mechanical impedance is sensitive even to small-sized structural defects. Conventional impedance measurements, however, have been based on electromechanical impedance (EMI) using contact-type piezoelectric transducers, which show deteriorated performances induced by the effects of a) Curie temperature limitations, b) electromagnetic interference (EMI), c) bonding layers and etc. This study aims to tackle the limitations of conventional EMI measurement by utilizing laser-based mechanical impedance (LMI) measurement. The LMI response, which is equivalent to a steady-state ultrasound response, is generated by shooting the pulse laser beam to the target structure, and is acquired by measuring the out-of-plane velocity using a laser vibrometer. The formation of the LMI response is observed through the thermo-mechanical finite element analysis. The feasibility of applying the LMI technique for damage detection is experimentally verified using a pipe specimen under high temperature environment.

  18. Table 1. Summary of Field Testing and Measurement Data

    Data.gov (United States)

    U.S. Environmental Protection Agency — Key performance parameters measured during the field demonstration such as lining thickness, compressive strength, Flexural Strength, Modulus of Elasticity, bond...

  19. Experimental measurements of the thermal conductivity of ash deposits: Part 1. Measurement technique

    Energy Technology Data Exchange (ETDEWEB)

    A. L. Robinson; S. G. Buckley; N. Yang; L. L. Baxter

    2000-04-01

    This paper describes a technique developed to make in situ, time-resolved measurements of the effective thermal conductivity of ash deposits formed under conditions that closely replicate those found in the convective pass of a commercial boiler. Since ash deposit thermal conductivity is thought to be strongly dependent on deposit microstructure, the technique is designed to minimize the disturbance of the natural deposit microstructure. Traditional techniques for measuring deposit thermal conductivity generally do not preserve the sample microstructure. Experiments are described that demonstrate the technique, quantify experimental uncertainty, and determine the thermal conductivity of highly porous, unsintered deposits. The average measured conductivity of loose, unsintered deposits is 0.14 {+-} 0.03 W/(m K), approximately midway between rational theoretical limits for deposit thermal conductivity.

  20. Influence of the jaw tracking technique on the dose calculation accuracy of small field VMAT plans.

    Science.gov (United States)

    Swinnen, Ans C C; Öllers, Michel C; Roijen, Erik; Nijsten, Sebastiaan M; Verhaegen, Frank

    2017-01-01

    The aim of this study was to evaluate experimentally the accuracy of the dose calculation algorithm AcurosXB in small field highly modulated Volumetric Modulated Arc Therapy (VMAT). The 1000SRS detector array inserted in the rotational Octavius 4D phantom (PTW) was used for 3D dose verification of VMAT treatments characterized by small to very small targets. Clinical treatment plans (n = 28) were recalculated on the phantom CT data set in the Eclipse TPS. All measurements were done on a Varian TrueBeamSTx, which can provide the jaw tracking technique (JTT). The effect of disabling the JTT, thereby fixing the jaws at static field size of 3 × 3 cm(2) and applying the MLC to shape the smallest apertures, was investigated for static fields between 0.5 × 0.5-3 × 3 cm(2) and for seven VMAT patients with small brain metastases. The dose calculation accuracy has been evaluated by comparing the measured and calculated dose outputs and dose distributions. The dosimetric agreement has been presented by a local gamma evaluation criterion of 2%/2 mm. Regarding the clinical plans, the mean ± SD of the volumetric gamma evaluation scores considering the dose levels for evaluation of 10%, 50%, 80% and 95% are (96.0 ± 6.9)%, (95.2 ± 6.8)%, (86.7 ± 14.8)% and (56.3 ± 42.3)% respectively. For the smallest field VMAT treatments, discrepancies between calculated and measured doses up to 16% are obtained. The difference between the 1000SRS central chamber measurements compared to the calculated dose outputs for static fields 3 × 3, 2 × 2, 1 × 1 and 0.5 × 0.5 cm(2) collimated with MLC whereby jaws are fixed at 3 × 3 cm(2) and for static fields shaped with the collimator jaws only (MLC retracted), is on average respectively, 0.2%, 0.8%, 6.8%, 5.7% (6 MV) and 0.1%, 1.3%, 11.7%, 21.6% (10 MV). For the seven brain mets patients was found that the smaller the target volumes, the higher the improvement in agreement between measured and calculated doses after disabling the JTT

  1. Protocol of measurement techniques - Project colored solar collectors

    Energy Technology Data Exchange (ETDEWEB)

    Schueler, A.; Chambrier, E. De; Roecker, Ch.; Scartezzini, J.-L.

    2004-08-15

    This illustrated annual report for the Swiss Federal Office of Energy (SFOE) takes a look at work done at the Swiss Federal Institute of Technology in Lausanne, Switzerland, on multi-layer, thin-film interference coatings for solar collector glazing. The correct combinations of refractive indices and film thickness are discussed. The authors state that corresponding multi-layered thin film stacks will have to be realised experimentally in a controlled and reproducible way. New thin film materials are to be tailored to exhibit optimised optical and ageing properties. The development of these coatings is to be based on various measurement techniques, such as spectro-photometry, measurements of total power throughput by means of a solar simulator, spectroscopic ellipsometry, scanning electron microscopy (SEM), X-ray diffraction (XRD) and X-ray photoelectron spectroscopy (XPS). The paper provides many examples of typical data and explains which film properties can be inferred from each method and thus describes both the function and purpose of the different measurement techniques.

  2. Equipment and Experimental Technique For Temperature Measurements In Deep Boreholes

    Science.gov (United States)

    Khristoforov, A.

    The technique of temperature measurements is highly informative since any dynami- cal processes in the boreholes and in the vicinities are accompanied by thermal effects. Electronics and equipment for remote measurements in the boreholes are briefly dis- cussed in the report. It includes a deep instrument, cable winch and surface recording unit placed onboard a car. The temperature dependent frequency modulated signal is used in deep instrument. A cable of original construction was developed for chute-lift operations. It has a signal and power channel at the same time and play the depth me- ter. The surface recording unit includes power supply for deep instruments, receiver, frequency meter and indicator. A personal computer is used for the measurement nu- merical control. Energy for the electronics is supplied by a car battery. Self sufficiency and high accuracy are specialities of the equipment. Using the technique and equip- ment we made the experimental study of temperature in the boreholes of the East European platform, Middle Asia, West Siberia, Kamchatka and other regions. Most of our temperatures and temperature gradients have been used for mapping.

  3. Combined FTIR-micrometeorological techniques for long term measurements of greenhouse gas fluxes from agriculture

    Energy Technology Data Exchange (ETDEWEB)

    Petersen, Anna Katinka [Institut fuer Umweltphysik (IUP), Universitaet Bremen (Germany); Griffith, David; Naylor, Travis [Centre for Atmospheric Chemistry, University of Wollongong, NSW (Australia); Harvey, Mike; Smith, Murray [National Institute of Water and Atmospheric Research (NIWA), Wellington (New Zealand)

    2009-07-01

    Agricultural systems can be sources or sinks of atmospheric trace gases, and the measurement of the fluxes is necessary when evaluating both the environmental impact of agricultural activities and the impact of atmospheric pollution on agricultural production and sustainability. With the exception of CO{sub 2}, micrometeorological measurements of the fluxes of greenhouse gases are still mostly possible only in campaign mode due to the complexity and logistical requirements of the existing techniques. We have developed an instrument system for long-term flux measurements through a combination of micrometeorological flux measurement techniques (Relaxed Eddy Accumulation (REA) and Flux-Gradient (FG)) with FTIR spectroscopy. The combined technique is capable of simultaneous flux measurements of N{sub 2}O, CH{sub 4} and CO{sub 2} at paddock to regional scales continuously, over longer terms. The system was tested on a 3 weeks field campaign. The flux of the atmospheric CO{sub 2} was measured by Relaxed Eddy Accumulation, Flux-Gradient, and Eddy Correlation. Simultaneously, fluxes of CH{sub 4} and N{sub 2}O were measured by REA and FG technique.

  4. Three-dimensional photogrammetric measurement of magnetic field lines in the WEGA stellarator

    Energy Technology Data Exchange (ETDEWEB)

    Drewelow, Peter; Braeuer, Torsten; Otte, Matthias; Wagner, Friedrich; Werner, Andreas [Max-Planck-Institut fuer Plasmaphysik, EURATOM Association, Wendelsteinstr. 1, D-17491 Greifswald (Germany)

    2009-12-15

    The magnetic confinement of plasmas in fusion experiments can significantly degrade due to perturbations of the magnetic field. A precise analysis of the magnetic field in a stellarator-type experiment utilizes electrons as test particles following the magnetic field line. The usual fluorescent detector for this electron beam limits the provided information to two-dimensional cut views at certain toroidal positions. However, the technique described in this article allows measuring the three-dimensional structure of the magnetic field by means of close-range photogrammetry. After testing and optimizing the main diagnostic components, measurements of the magnetic field lines were accomplished with a spatial resolution of 5 mm. The results agree with numeric calculations, qualifying this technique as an additional tool to investigate magnetic field configurations in a stellarator. For a possible future application, ways are indicated on how to reduce experimental error sources.

  5. Three-dimensional photogrammetric measurement of magnetic field lines in the WEGA stellarator.

    Science.gov (United States)

    Drewelow, Peter; Bräuer, Torsten; Otte, Matthias; Wagner, Friedrich; Werner, Andreas

    2009-12-01

    The magnetic confinement of plasmas in fusion experiments can significantly degrade due to perturbations of the magnetic field. A precise analysis of the magnetic field in a stellarator-type experiment utilizes electrons as test particles following the magnetic field line. The usual fluorescent detector for this electron beam limits the provided information to two-dimensional cut views at certain toroidal positions. However, the technique described in this article allows measuring the three-dimensional structure of the magnetic field by means of close-range photogrammetry. After testing and optimizing the main diagnostic components, measurements of the magnetic field lines were accomplished with a spatial resolution of 5 mm. The results agree with numeric calculations, qualifying this technique as an additional tool to investigate magnetic field configurations in a stellarator. For a possible future application, ways are indicated on how to reduce experimental error sources.

  6. Measuring the effect of field viability on wheat yield

    DEFF Research Database (Denmark)

    Olsen, Jakob Vesterlund; Schou, Jesper Sølver

    showing a significant effect on yields. Further research may involve estimating the effect of field characteristics on the aggregated economic farm performance. The field viability index has multiple applications in e.g. benchmarking, leasing or buying arrangements, and for identifying potential land...... contributes by introducing a new joint index for field shape and field size, field viability index (FVI), aiming at measuring the effect of land fragmentation on farm performance based on field characteristics. The index is calculated for Danish wheat fields and is tested on a large sample of Danish farmers...

  7. A Comparison of Stellar Elemental Abundance Techniques and Measurements

    Science.gov (United States)

    Hinkel, Natalie R.; Young, Patrick A.; Pagano, Michael D.; Desch, Steven J.; Anbar, Ariel D.; Adibekyan, Vardan; Blanco-Cuaresma, Sergi; Carlberg, Joleen K.; Delgado Mena, Elisa; Liu, Fan; Nordlander, Thomas; Sousa, Sergio G.; Korn, Andreas; Gruyters, Pieter; Heiter, Ulrike; Jofré, Paula; Santos, Nuno C.; Soubiran, Caroline

    2016-09-01

    Stellar elemental abundances are important for understanding the fundamental properties of a star or stellar group, such as age and evolutionary history, as well as the composition of an orbiting planet. However, as abundance measurement techniques have progressed, there has been little standardization between individual methods and their comparisons. As a result, different stellar abundance procedures determine measurements that vary beyond the quoted error for the same elements within the same stars. The purpose of this paper is to better understand the systematic variations between methods and offer recommendations for producing more accurate results in the future. We invited a number of participants from around the world (Australia, Portugal, Sweden, Switzerland, and the United States) to calculate 10 element abundances (C, O, Na, Mg, Al, Si, Fe, Ni, Ba, and Eu) using the same stellar spectra for four stars (HD 361, HD 10700, HD 121504, and HD 202206). Each group produced measurements for each star using (1) their own autonomous techniques, (2) standardized stellar parameters, (3) a standardized line list, and (4) both standardized parameters and a line list. We present the resulting stellar parameters, absolute abundances, and a metric of data similarity that quantifies the homogeneity of the data. We conclude that standardization of some kind, particularly stellar parameters, improves the consistency between methods. However, because results did not converge as more free parameters were standardized, it is clear there are inherent issues within the techniques that need to be reconciled. Therefore, we encourage more conversation and transparency within the community such that stellar abundance determinations can be reproducible as well as accurate and precise.

  8. Determination of hyperfine fields orientation in nuclear probe techniques

    Science.gov (United States)

    Szymański, K.; Olszewski, W.; Satuła, D.; Gawryluk, D. J.; Krzton-Maziopa, A.; Kalska-Szostko, B.

    2017-02-01

    One of the most popular nuclear probes, 57Fe is used for the investigation of orientations of hyperfine fields and also for the determination of other important properties. In particular, the orientation of iron magnetic moments can be unambiguously determined, including its signs. Experiments with polarized radiation are presented with regard to selected systems. Orientation of electric field gradient is used for acquiring information about the shape of the texture-free spectra. Applications on the analysis of iron-based superconductors are presented.

  9. Dewatering Techniques for Gas Recovery in Sichuan Gas Fields

    Institute of Scientific and Technical Information of China (English)

    Xu Kefang

    1996-01-01

    @@ Through several years' study for geology and development behavior of the gas fields, we realized that the water-bearing gas pools in Sichuan gas fields almost belong to enclosed weak elastic water drive gas pools, whether edge water gas pools or bottom water gas pools. According to the verification of drilling and production behavior data, in the periphery of Sichuan water-bearing gas pools, a screen is formed by gypsum salt, mudstone, or tight bed rock, with very low permeability, which blocks water percolation.

  10. An Adaptive Filtering Algorithm using Mean Field Annealing Techniques

    OpenAIRE

    Persson, Per; Nordebo, Sven; Claesson, Ingvar

    2002-01-01

    We present a new approach to discrete adaptive filtering based on the mean field annealing algorithm. The main idea is to find the discrete filter vector that minimizes the matrix form of the Wiener-Hopf equations in a least-squares sense by a generalized mean field annealing algorithm. It is indicated by simulations that this approach, with complexity O(M^2) where M is the filter length, finds a solution comparable to the one obtained by the recursive least squares (RLS) algorithm but withou...

  11. A field technique for estimating aquifer parameters using flow log data

    Science.gov (United States)

    Paillet, Frederick L.

    2000-01-01

    A numerical model is used to predict flow along intervals between producing zones in open boreholes for comparison with measurements of borehole flow. The model gives flow under quasi-steady conditions as a function of the transmissivity and hydraulic head in an arbitrary number of zones communicating with each other along open boreholes. The theory shows that the amount of inflow to or outflow from the borehole under any one flow condition may not indicate relative zone transmissivity. A unique inversion for both hydraulic-head and transmissivity values is possible if flow is measured under two different conditions such as ambient and quasi-steady pumping, and if the difference in open-borehole water level between the two flow conditions is measured. The technique is shown to give useful estimates of water levels and transmissivities of two or more water-producing zones intersecting a single interval of open borehole under typical field conditions. Although the modeling technique involves some approximation, the principle limit on the accuracy of the method under field conditions is the measurement error in the flow log data. Flow measurements and pumping conditions are usually adjusted so that transmissivity estimates are most accurate for the most transmissive zones, and relative measurement error is proportionately larger for less transmissive zones. The most effective general application of the borehole-flow model results when the data are fit to models that systematically include more production zones of progressively smaller transmissivity values until model results show that all accuracy in the data set is exhausted.A numerical model is used to predict flow along intervals between producing zones in open boreholes for comparison with measurements of borehole flow. The model gives flow under quasi-steady conditions as a function of the transmissivity and hydraulic head in an arbitrary number of zones communicating with each other along open boreholes. The

  12. A review on real time physical measurement techniques and their attempt to predict wear-out status of IGBT

    DEFF Research Database (Denmark)

    Ghimire, Pramod; Beczkowski, Szymon; Munk-Nielsen, Stig;

    2013-01-01

    quality and some practical issues of those measurement techniques are discussed. Furthermore, the paper proposes the requirements for the measurement and prognostic approach to determine wear-out status of power modules in field applications. The online Vce measurement for a selected topology is also...

  13. Electrical conductivity measurements on silicate melts using the loop technique

    Science.gov (United States)

    Waff, H. S.

    1976-01-01

    A new method is described for measurement of the electrical conductivity of silicate melts under controlled oxygen partial pressure at temperatures to 1550 C. The melt samples are suspended as droplets on platinum-rhodium loops, minimizing iron loss from the melt due to alloying with platinum, and providing maximum surface exposure of the melt to the oxygen-buffering gas atmosphere. The latter provides extremely rapid equilibration of the melt with the imposed oxygen partial pressure. The loop technique involves a minimum of setup time and cost, provides reproducible results to within + or - 5% and is well suited to electrical conductivity studies on silicate melts containing redox cations.

  14. Evaluation of Two Computational Techniques of Calculating Multipath Using Global Positioning System Carrier Phase Measurements

    Science.gov (United States)

    Gomez, Susan F.; Hood, Laura; Panneton, Robert J.; Saunders, Penny E.; Adkins, Antha; Hwu, Shian U.; Lu, Ba P.

    1996-01-01

    Two computational techniques are used to calculate differential phase errors on Global Positioning System (GPS) carrier war phase measurements due to certain multipath-producing objects. The two computational techniques are a rigorous computati electromagnetics technique called Geometric Theory of Diffraction (GTD) and the other is a simple ray tracing method. The GTD technique has been used successfully to predict microwave propagation characteristics by taking into account the dominant multipath components due to reflections and diffractions from scattering structures. The ray tracing technique only solves for reflected signals. The results from the two techniques are compared to GPS differential carrier phase ns taken on the ground using a GPS receiver in the presence of typical International Space Station (ISS) interference structures. The calculations produced using the GTD code compared to the measured results better than the ray tracing technique. The agreement was good, demonstrating that the phase errors due to multipath can be modeled and characterized using the GTD technique and characterized to a lesser fidelity using the DECAT technique. However, some discrepancies were observed. Most of the discrepancies occurred at lower devations and were either due to phase center deviations of the antenna, the background multipath environment, or the receiver itself. Selected measured and predicted differential carrier phase error results are presented and compared. Results indicate that reflections and diffractions caused by the multipath producers, located near the GPS antennas, can produce phase shifts of greater than 10 mm, and as high as 95 mm. It should be noted tl the field test configuration was meant to simulate typical ISS structures, but the two environments are not identical. The GZ and DECAT techniques have been used to calculate phase errors due to multipath o the ISS configuration to quantify the expected attitude determination errors.

  15. Closure measuring technique on the datum of an end-tooth indexing table

    Science.gov (United States)

    Ling, Siying; Lou, Zhifeng; Wang, Liding

    2012-04-01

    The end-tooth indexing table (EIT) is widely used as angular reference in precision measurement or precision manufacturing fields. In order to improve the pitch accuracy of ultra-precision master gears, we designed an automatic end-tooth indexing system on a specific gear grinder. Theoretically, the indexing accuracy of an EIT can reach ±0.2″ or even more, which can meet the machining requirements of ultra-precision gears with pitch deviation up to grade 0 (ISO1328-1:1995). However, the axial and radial misalignment of an EIT to the spindle will decrease the indexing accuracy of the gear grinder. In order to solve this difficulty, precision measurement and lapping on the datum face of an EIT will be necessary. How to measure the parallelism deviation correctly at the datum of the mating face of the EIT will be another difficulty. Using the closure measuring technique which allows error separation, in this paper the measurement platform is set up, the data acquisition and handling method are presented and an experimental measurement is carried out. The maximum parallelism deviation, which is between the target face of an EIT and its mating face, was reduced from about 4 to 0.29 µm by adopting the closure measuring technique and precision lapping. It confirms that the closure measuring technique can implement precision measurement of dimensional measurands for an axisymmetric part.

  16. Pressure-field extraction from Lagrangian flow measurements: first experiences with 4D-PTV data

    Science.gov (United States)

    Neeteson, N. J.; Bhattacharya, S.; Rival, D. E.; Michaelis, D.; Schanz, D.; Schröder, A.

    2016-06-01

    As a follow-up to a previous proof-of-principle study, a novel Lagrangian pressure-extraction technique is analytically evaluated, and experimentally validated using dense 4D-PTV data. The technique is analytically evaluated using the semi-three-dimensional Taylor-Green vortex, and it is found that the Lagrangian technique out-performs the standard Eulerian technique when Dirichlet boundary conditions are enforced. However, the Lagrangian technique produces worse estimates of the pressure field when Neumann boundary conditions are enforced on boundaries with strong pressure gradients. The technique is experimentally validated using flow data obtained for the case of a free-falling, index-matched sphere at Re=2100. The experimental data were collected using a four-camera particle tracking velocimetry measurement system, and processed using 4D-PTV. The pressure field is then extracted using both the Eulerian and Lagrangian techniques, and the resulting pressure fields are compared. Qualitatively, the pressure fields agree; however, quantitative differences are found with respect to the magnitude of the pressure minima on the side of the sphere. Finally, the pressure-drag coefficient is estimated using each technique, and the two techniques are found to be in very close agreement. A comparison to a reference value from literature confirms that the drag coefficient estimates are reasonable, demonstrating the validity of the technique.

  17. Field temperature measurements at Erta'Ale Lava Lake, Ethiopia

    Science.gov (United States)

    Burgi, Pierre-Yves; Caillet, Marc; Haefeli, Steven

    2002-06-01

    The shield volcano Erta'Ale, situated in the Danakil Depression, Ethiopia, is known for its active lava lake. In February 2001, our team visited this lake, located inside an 80-m-deep pit, to perform field temperature measurements. The distribution and variation of temperature inside the lake were obtained on the basis of infrared radiation measurements performed from the rim of the pit and from the lake shores. The crust temperature was also determined from the lake shores with a thermocouple to calibrate the pyrometer. We estimated an emissivity of the basalt of 0.74 from this experiment. Through the application of the Stefan-Boltzmann law, we then obtained an estimate of the total radiative heat flux, constrained by pyrometer measurements of the pit, and visual observations of the lake activity. Taking into account the atmospheric convective heat flux, the convected magma mass flux needed to balance the energy budget was subsequently derived and found to represent between 510 and 580 kg s-1. The surface circulation of this mass flux was also analyzed through motion processing techniques applied to video images of the lake. Electronic supplementary material to this paper can be obtained by using the Springer LINK server located at http://dx.doi.org/10.1007/s00445-002-0224-3.

  18. COMPARING FIELD PERFORMANCES OF DENUDER TECHNIQUES IN THE HIGH ARCTIC

    Science.gov (United States)

    A field evaluation between two annular denuder system configurations was conducted during the spring of 2003 in the marine Arctic (Ny-Ålesund, Svalbard). The IIA annular denuder system (ADS) employs a series of five single channel annular denuders, a cyclone and a filter pack to ...

  19. Anaesthesia in the field. Spontaneous ventilation--a new technique.

    Science.gov (United States)

    Restall, J; Thompson, M C; Johnston, I G; Fenton, T C

    1990-11-01

    In recent years the British Army has used the Triservice Anaesthetic Apparatus in the field. Trichloroethylene is no longer manufactured in the United Kingdom and halothane is not recommended for closely repeated anaesthetics. A method based on existing equipment is described for patients breathing spontaneously. A background infusion of ketamine, midazolam and alfentanil supplements the inhalation of isoflurane in oxygen-enriched air.

  20. Principles of planar near-field antenna measurements

    CERN Document Server

    Gregson, Stuart; Parini, Clive

    2007-01-01

    This single volume provides a comprehensive introduction and explanation of both the theory and practice of 'Planar Near-Field Antenna Measurement' from its basic postulates and assumptions, to the intricacies of its deployment in complex and demanding measurement scenarios.

  1. Field measurement and analysis of harmonic levels

    Energy Technology Data Exchange (ETDEWEB)

    Karunakara, K.; Muthu Kumar, E.; Rajesh Kumar, O.; Nambudiri, P.V.V.; Srinivasan, K.N. [Central Power Research Institute, Bangalore (India)

    1999-07-01

    The level of harmonics on the transmission and distribution network is rising over the years, due to the rapid development and usage of electronic and semiconductor devices in the industries, as these devices produce harmonic currents. As the harmonic currents produced by these devices are unproductive and affect the ideal sinusoidal waveshapes, these have to be limited to a tolerable limit at the Point of Common Coupling (PCC). Before setting a tolerable limit on harmonics it is necessary to know the level of harmonics already present in the system, so that the limits suggested are comprehensive and practicable. To have a fair idea about the current and voltage harmonics on the Indian system, Central Power Research Institute (CPRI) has carried out a lot of measurements both on the distribution network and transmission network over the past 13 years. This paper discusses the harmonic measurements carried out by CPRI on different loads and voltage levels on the Indian network. The methodology adopted for measurement and results are also discussed in this paper. (author)

  2. Side abutment pressure distribution by field measurement

    Institute of Scientific and Technical Information of China (English)

    WANG Lian-guo; SONG Yang; HE Xing-hua; ZHANG Jian

    2008-01-01

    Given the 7123 working face in the Qidong Coal Mine of the Wanbei Mining Group, nine dynamic roof monitors were installed in the crossheading to measure the amount and velocity of roof convergence in different positions and at different times and three steel bored stress sensors were installed in the return airway to measure rock stress at depth. On the basis of this arrangement, the rule of change of the distribution of the side abutment pressure with the advance of the working face and movement of overlying strata was studied. The rule of change and the stability of rock stress at depth were measured. Secondly, the affected area and stability time of the side abutment pressure were also studied. The results show that: 1) During working, the face advanced distance was from 157 m to 99 m, the process was not effected by mining induced pressure. When the distance was 82 m, the position of peak stress was 5 m away from the coal wall. When the distance was 37 m, the position of peak stress away from the coal wall was about 15 m to 20 m and finally reached a steady state; 2) the time and the range of the peak of side rock pressure obtained from stress sensors were consistent with the results from the dynamic roof monitors; 3) the position of the peak pressure was 25 m away from the coal wall.

  3. Velocity fields as a tracer from magnetic fields in sub-alfv\\'enic regimes: The Velocity Gradient Technique

    CERN Document Server

    González-Casanova, Diego F

    2016-01-01

    Strong Alfv\\'enic turbulence develops eddy-like motions perpendicular to the local direction of magnetic fields. This local alignment induces velocity gradients perpendicular to the local direction of the magnetic field. We use this fact to propose a new technique of studying the direction of magnetic fields from observations, the Velocity Gradient Technique. We test our idea by employing the synthetic observations obtained via 3D MHD numerical simulations for different sonic and Alfv\\'en Mach numbers. We calculate the velocity gradient, $\\mathbf{\\Omega}$, using the velocity centroids. We find that $\\mathbf{\\Omega}$ traces the projected magnetic field best for the synthetic maps obtained with sub-Alfv\\'enic simulations providing good point-wise correspondence between the magnetic field direction and that of $\\mathbf{\\Omega}$. The reported alignment is much better than the alignment between the density gradients and the magnetic field and we demonstrated that it can be used to find the magnetic field strength ...

  4. A Controlled Field Pilot for Testing Near Surface CO2 Detection Techniques and Transport Models

    Science.gov (United States)

    Spangler, L. H.; Dobeck, L.

    2007-12-01

    A field facility has been developed to allow controlled studies of near surface CO2transport and detection technologies. The key component of the facility is a shallow horizontal, well slotted over 70m of its length and divided into seven zones via packers with mass flow control in each individual zone. The scale and fluxes were designed to address large scale CO2 storage projects and desired retention rates for those projects and those design parameters will be discussed. A wide variety of detection techniques were deployed by collaborators from Los Alamos National Lab, Lawrence Berkeley National Lab, the National Energy Technology Lab, Pacific Northwest National Lab, Lawrence Livermore National Lab and West Virginia University. Techniques included eddy covariance, soil gas measurements, hyperspectral imaging for plant stress detection, differential absorption LIDAR (both free space atmospheric and below surface soil gas), tracer studies, water sampling, stable isotope studies, and soil flux chambers. An overview of these results will be presented.

  5. Lamb-shift and electric field measurements in plasmas

    Science.gov (United States)

    Doveil, F.; Chérigier-Kovacic, L.; Ström, P.

    2017-01-01

    The electric field is a quantity of particular relevance in plasma physics. Indeed, its fluctuations are responsible for different macroscopic phenomena such as anomalous transport in fusion plasmas. Answering a long-standing challenge, we offer a new method to locally and non-intrusively measure weak electric fields and their fluctuations in plasmas, by means of a beam of hydrogen ions or atoms. We present measurements of the electric field in vacuum and in a plasma where Debye shielding is measured. For the first time, we have used the Lamb-shift resonance to measure oscillating electric fields around 1 GHz and observed the strong enhancement of the Lyman-α signal. The measurement is both direct and non-intrusive. This method provides sensitivity (mV cm-1) and temporal resolution (ns) that are three orders higher compared to current diagnostics. It thus allows measuring fluctuations of the electric field at scales not previously reached experimentally.

  6. Rapid Field Measurement of Dissolved Inorganic Carbon Based on CO{sub 2} Analysis

    Energy Technology Data Exchange (ETDEWEB)

    VESPER, DJ, Edenborn, Harry

    2012-01-01

    Dissolved inorganic carbon (DIC) is commonly measured in water and is an important parameter for understanding carbonate equilibrium, carbon cycling, and water-rock interaction. While accurate measurements can be made in the analytical laboratory, we have developed a rapid, portable technique that can be used to obtain accurate and precise data in the field as well.

  7. REMANENCE MEASUREMENTS ON INDIVIDUAL MAGNETOTACTIC BACTERIA USING A PULSED MAGNETIC-FIELD

    NARCIS (Netherlands)

    PENNINGA, Ietje; Waard , de Hendrik; MOSKOWITZ, BM; BAZYLINSKI, DA; FRANKEL, RB

    1995-01-01

    We describe pulsed-magnetic-field remanence measurements of individual, killed, undisrupted cells of three different types of magnetotactic bacteria. The measurement technique involved the observation of aligned, individual magnetotactic bacteria with a light microscope as they were subjected to mag

  8. Comparison of bone density measurement techniques: DXA and Archimedes' principle.

    Science.gov (United States)

    Keenan, M J; Hegsted, M; Jones, K L; Delany, J P; Kime, J C; Melancon, L E; Tulley, R T; Hong, K D

    1997-11-01

    The standard method for determination of density (g/cm3) of bones from small animals has been the application of Archimedes' principle. A recent development has been software for the determination of "density" (g/cm2) of small animal bones with dual-energy X-ray absorptiometry (DXA). We compared Archimedes' principle and DXA (Hologic QDR-2000) in the measurement of the densities of whole and hollowed femurs of 5- to 6-month-old retired female breeder rats. In an attempt to ensure detectable treatment differences, rats were used from a low-vitamin D Holtzman and a supplemental-vitamin D Sprague-Dawley colony. Whole femur densities were higher for supplemental-vitamin D colony rats than for low vitamin D rats using both techniques (Archimedes' principle, p Archimedes' principle than for DXA. Other variables such as femur ash weight and calcium content were also highly correlated to densities with both techniques. Hollowed femur density values were higher than whole femur values with Archimedes' principle but lower with DXA. Colony effects for hollowed femur densities were diminished with Archimedes' principle (p < 0.03) and eliminated with DXA (p < 0.53). Investigation of whole bones is more biologically relevant, and both techniques were effective in detecting differences between whole femurs from low-vitamin D and supplemental-vitamin D colony rats.

  9. Flowing dusty plasma experiments: Generation of flow and measurement techniques

    CERN Document Server

    Jaiswal, S; Sen, A

    2016-01-01

    A variety of experimental techniques for the generation of subsonic/supersonic dust fluid flows and means of measuring such flow velocities are presented. The experiments have been carried out in a $\\Pi-$shaped Dusty Plasma Experimental (DPEx) device with micron size kaolin/Melamine Formaldehyde (MF) particles embedded in a background of Argon plasma created by a direct current (DC) glow discharge. A stationary dust cloud is formed over the cathode region by precisely balancing the pumping speed and gas flow rate. A flow of dust particles/fluid is generated by additional gas injection from a single or dual locations or by altering the dust confining potential. The flow velocity is then estimated by three different techniques, namely, by super Particle Identification (sPIT) code, Particle Image Velocimetry (PIV) analysis and the excitation of Dust Acoustic Waves (DAWs). The results obtained from these three different techniques along with their merits and demerits are discussed. An estimation of the neutral dr...

  10. Improved technique for blood flow velocity measurement using Doppler effect

    Science.gov (United States)

    Valadares Oliveira, Eduardo J.; Nantes Button, Vera L. d. S.; Maia, Joaquim M.; Costa, Eduardo T.

    2002-04-01

    The Doppler velocimeter developed allows to determine the angle between the ultrasonic beam and the velocity vector of the flow, and to calculate the precise blood flow in a vessel. Four piezoelectric transducers constitute the Doppler velocimeter. Three of these transducers are positioned to form an equilateral triangle (base of a pyramid). When these transducers move simultaneously, backward or forward from the initial position, the emitted ultrasonic beams focalize on a position (peak of the pyramid) closer or farther from the transducers faces, according to the depth of the vessel where we intend to measure de flow. The angle between the transducers allows adjusting the height of this pyramid and the position of the focus (where the three beams meet). A forth transducer is used to determine the diameter of the vessel and monitor the position of the Doppler velocimeter relative to the vessel. Simulation results showed that with this technique is possible to accomplish precise measurement of blood flow.

  11. Single-shot spatiotemporal measurements of high-field terahertz pulses

    Energy Technology Data Exchange (ETDEWEB)

    van Tilborg, Jeroen; Schroeder, Carl; Toth, Csaba; Geddes, Cameron; Esarey, Eric; Leemans, Wim

    2011-06-17

    The electric field profiles of broad-bandwidth coherent terahertz (THz) pulses, emitted by laser-wakefield-accelerated electron bunches, are studied. The near-single-cycle THz pulses are measured with two single-shot techniques in the temporal and spatial domains. Spectra of 0-6 THz and peak fields up to {approx_equal} 0.4 MV cm{sup -1} are observed. The measured field substructure demonstrates the manifestation of spatiotemporal coupling at focus, which affects the interpretation of THz radiation as a bunch diagnostic and in high-field pump-probe experiments.

  12. Measuring the Earth's Magnetic Field in a Laboratory

    Science.gov (United States)

    Cartacci, A.; Straulino, S.

    2008-01-01

    Two methods for measuring the Earth's magnetic field are described. In the former, according to Gauss, the Earth's magnetic field is compared with that of a permanent magnet; in the latter, a well-known method, the comparison is made with the magnetic field generated by a current. As all the used instruments are available off the shelf, both…

  13. Comparisons between different techniques for measuring mass segregation

    CERN Document Server

    Parker, Richard J

    2015-01-01

    We examine the performance of four different methods which are used to measure mass segregation in star-forming regions: the radial variation of the mass function $\\mathcal{M}_{\\rm MF}$; the minimum spanning tree-based $\\Lambda_{\\rm MSR}$ method; the local surface density $\\Sigma_{\\rm LDR}$ method; and the $\\Omega_{\\rm GSR}$ technique, which isolates groups of stars and determines whether the most massive star in each group is more centrally concentrated than the average star. All four methods have been proposed in the literature as techniques for quantifying mass segregation, yet they routinely produce contradictory results as they do not all measure the same thing. We apply each method to synthetic star-forming regions to determine when and why they have shortcomings. When a star-forming region is smooth and centrally concentrated, all four methods correctly identify mass segregation when it is present. However, if the region is spatially substructured, the $\\Omega_{\\rm GSR}$ method fails because it arbitra...

  14. High frequency magnetic field technique: mathematical modelling and development of a full scale water fraction meter

    Energy Technology Data Exchange (ETDEWEB)

    Cimpan, Emil

    2004-09-15

    This work is concerned with the development of a new on-line measuring technique to be used in measurements of the water concentration in a two component oil/water or three component (i.e. multiphase) oil/water/gas flow. The technique is based on using non-intrusive coil detectors and experiments were performed both statically (medium at rest) and dynamically (medium flowing through a flow rig). The various coil detectors were constructed with either one or two coils and specially designed electronics were used. The medium was composed by air, machine oil, and water having different conductivity values, i.e. seawater and salt water with various conductivities (salt concentrations) such as 1 S/m, 4.9 S/m and 9.3 S/m. The experimental measurements done with the different mixtures were further used to mathematically model the physical principle used in the technique. This new technique is based on measuring the coil impedance and signal frequency at the self-resonance frequency of the coil to determine the water concentration in the mix. By using numerous coils it was found, experimentally, that generally both the coil impedance and the self-resonance frequency of the coil decreased as the medium conductivity increased. Both the impedance and the self-resonance frequency of the coil depended on the medium loss due to the induced eddy currents within the conductive media in the mixture, i.e. water. In order to detect relatively low values of the medium loss, the self-resonance frequency of the coil and also of the magnetic field penetrating the media should be relatively high (within the MHz range and higher). Therefore, the technique was called and referred to throughout the entire work as the high frequency magnetic field technique (HFMFT). To practically use the HFMFT, it was necessary to circumscribe an analytical frame to this technique. This was done by working out a mathematical model that relates the impedance and the self-resonance frequency of the coil to the

  15. Computation of electrostatic fields in anisotropic human tissues using the Finite Integration Technique (FIT)

    Science.gov (United States)

    Motresc, V. C.; van Rienen, U.

    2004-05-01

    The exposure of human body to electromagnetic fields has in the recent years become a matter of great interest for scientists working in the area of biology and biomedicine. Due to the difficulty of performing measurements, accurate models of the human body, in the form of a computer data set, are used for computations of the fields inside the body by employing numerical methods such as the method used for our calculations, namely the Finite Integration Technique (FIT). A fact that has to be taken into account when computing electromagnetic fields in the human body is that some tissue classes, i.e. cardiac and skeletal muscles, have higher electrical conductivity and permittivity along fibers rather than across them. This property leads to diagonal conductivity and permittivity tensors only when expressing them in a local coordinate system while in a global coordinate system they become full tensors. The Finite Integration Technique (FIT) in its classical form can handle diagonally anisotropic materials quite effectively but it needed an extension for handling fully anisotropic materials. New electric voltages were placed on the grid and a new averaging method of conductivity and permittivity on the grid was found. In this paper, we present results from electrostatic computations performed with the extended version of FIT for fully anisotropic materials.

  16. Computation of electrostatic fields in anisotropic human tissues using the Finite Integration Technique (FIT

    Directory of Open Access Journals (Sweden)

    V. C. Motresc

    2004-01-01

    Full Text Available The exposure of human body to electromagnetic fields has in the recent years become a matter of great interest for scientists working in the area of biology and biomedicine. Due to the difficulty of performing measurements, accurate models of the human body, in the form of a computer data set, are used for computations of the fields inside the body by employing numerical methods such as the method used for our calculations, namely the Finite Integration Technique (FIT. A fact that has to be taken into account when computing electromagnetic fields in the human body is that some tissue classes, i.e. cardiac and skeletal muscles, have higher electrical conductivity and permittivity along fibers rather than across them. This property leads to diagonal conductivity and permittivity tensors only when expressing them in a local coordinate system while in a global coordinate system they become full tensors. The Finite Integration Technique (FIT in its classical form can handle diagonally anisotropic materials quite effectively but it needed an extension for handling fully anisotropic materials. New electric voltages were placed on the grid and a new averaging method of conductivity and permittivity on the grid was found. In this paper, we present results from electrostatic computations performed with the extended version of FIT for fully anisotropic materials.

  17. Comparison of different antenna diagnostics techniques with limited far field data input

    DEFF Research Database (Denmark)

    Pivnenko, Sergey; Cappellin, Cecilia

    2015-01-01

    In this paper, three different antenna diagnostics techniques are compared for the case when the input far-field data represent only few complete cuts or a two-dimensional grid with a limited angular sector. The techniques are applied to several different antennas: a high-gain offset reflector...... and extreme near fields....

  18. Teach Like a Champion Field Guide: A Practical Resource to Make the 49 Techniques Your Own

    Science.gov (United States)

    Lemov, Doug

    2012-01-01

    In his acclaimed book "Teach Like a Champion", Doug Lemov shared 49 essential techniques used by excellent teachers. In his companion Field Guide, he further explores those techniques in a practical guide. With the "Teach Like a Champion Field Guide", teachers will have an indispensable resource that complements their classroom application of…

  19. Measurement of Temperature Fields in Long Span Concrete Bridges

    Directory of Open Access Journals (Sweden)

    J. Římal

    2001-01-01

    Full Text Available This paper deals with assesing of the influence of climate temperatures on deformations and stresses in a cross section of the Nusle Bridge. The main purpose is to describe the measurement of the thermal fields, to compare measured and computed temperature fields, and to provide a real estimation of the stresses that occur.

  20. Atmospheric NO2 concentration measurements using differential absorption lidar technique

    Science.gov (United States)

    Devara, P. C. S.; Raj, P. Ernest

    1992-02-01

    Using the Differential Absorption Lidar (DIAL) technique, two types of approaches, namely, reflection from retroreflector / topographic target and backscatter from atmosphere, are available for studying remotely the atmospheric NO2 concentration. The Argon ion lidar system at the Indian Institute of Tropical Meteorology (IITM), Pune, India has been used for the measurements by following both the path-averaged and range-resolved approaches. For the former, a topographic target (hill) is used for determining path-averaged surface concentration. In the latter, spectral properties of atmospheric attenuation is used for making range-resolved measurements in the surface layer. The results of the observations collected by following both approaches are presented. The average surface NO2 concentration was found to vary between 0.01 and 0.105 ppm and the range-resolved measurements exhibited higher values suggesting treatment of the lidar data for scattering and extinction effects due to atmospheric aerosols and air molecules, and atmospheric turbulence. Certain modifications that are suggested to the experimental set-up, data acquisition and analysis to improve the measurements are briefly described.

  1. Rainbow technique for multi-parameter measurement of absorbing cylinder

    Institute of Scientific and Technical Information of China (English)

    Feihu Song; Chuanlong Xu; Shimin Wang

    2013-01-01

    Rainbow refractometry is widely used to measure the radius and real part of refractive index of a cylinder.However,studies on the detection of imaginary part of the refractive index with rainbow technique were scarce.This paper presents a new method for simultaneously measuring the radius,real and imaginary part of the refractive index of a cylinder,on the basis of the Airy theory and the Bouguer theory.The rainbows produced by the illuminated cylinder at a capillary exit are captured by a CCD camera in a labscale system,and then processed by the proposed method.Experimental results showed that the radius,real and imaginary part of the refractive index can be accurately determined when the SNR (signal to noise ratio) of the ripple structure is sufficiently high.However,the SNR of the ripple structure gradually decreases with decreasing scattering intensity of the cylinder,leading to larger measurement errors of the radius and real part of the refractive index.The relative error of the imaginary part of the refractive index derived from the measurement errors of the radius and real part of the refractive index,is less than 3.4%.

  2. Downscaling wind energy resource from mesoscale to microscale model and data assimilating field measurements

    Science.gov (United States)

    Duraisamy, V. J.; Dupont, E.; Carissimo, B.

    2014-12-01

    The main objective of this research work is to develop and evaluate several coupling methods between operational Numerical Weather Prediction (NWP) model and Computational Fluid Dynamics (CFD) model and data assimilate the field measurements into the CFD model. To address the problem of high spatial variation of the topography on the domain lateral boundaries between NWP and CFD domain boundaries, 3 methods - translation, extrapolation and Cressman interpolation are used to impose the NWP model data on the CFD domain lateral boundaries. Newtonian relaxation data assimilation technique is used to incorporate the field measurement data into the CFD simulations. These techniques are studied in a complex site located in southern France. Comparison of wind profiles between the CFD simulation, measurements and CFD simulation with data assimilation are discussed. This combination of state-of-the-art techniques in NWP, CFD, and field data assimilation will provide the basis of a more accurate wind resource assessment method.

  3. Simultaneous drift, microsaccades, and ocular microtremor measurement from a single noncontact far-field optical sensor

    Science.gov (United States)

    Ryle, James P.; Vohnsen, Brian; Sheridan, John T.

    2015-02-01

    We report on the combined far-field measurement of the three involuntary eye movements, drift, microsaccades, and ocular microtremor (OMT), using a noncontact far-field optical method. We review the significance of the smallest and least measured, and thus least understood, of the three, OMT. Using modern digital imaging techniques, we perform detailed analysis, present experimental results, and examine the extracted parameters using a noncontact far-field sensor. For the first time, in vivo noncontact measurements of all three fixational in-plane movements of the human eye are reported, which simultaneously provide both the horizontal (left-right) and vertical (up-down) displacement results.

  4. Infrared measurement and simulation of magnesium alloy welding temperature field

    Institute of Scientific and Technical Information of China (English)

    LIU Liming; CHI Mingsheng; HUANG Ruisheng; SONG Gang; ZHOU Yang

    2005-01-01

    The welding temperature field of magnesium alloy AZ31 welded by TIG was measured with the uncooled infrared (IR) thermal imaging technology. The variables in the mathematic mode of welding temperature fields were revised by IR temperature data. Based on the results of simulation, the loss of temperature fields caused by arc interfered was compensated, and a whole temperature field was achieved, which provided a precise and powerful foundation for the investigation of microstructure of the joints.

  5. Measurement of electric fields and estimation of dielectric susceptibility

    Science.gov (United States)

    Nogi, Yasuyuki; Suzuki, Kiyomitsu; Ohkuma, Yasunori

    2013-05-01

    We describe a method of measuring the spatial structures of electric fields produced by charge distributions such as those on strip electrodes, small disk electrodes, and long double-plate electrodes. An electric-field sensor with high sensitivity to ac fields is fabricated for the measurement using a thin copper sheet. The reliability of the sensor is confirmed using a parallel-plate capacitor. The electric fields are oscillated at a frequency of 300 kHz to operate the electric-field sensor successfully. The structures of the measured fields coincide well with those of theoretical fields derived from Coulomb's law. When a dielectric is inserted in an electric field, polarization charges appear on the surface of the dielectric and modify the electric field in empty space. We measure the modified field and confirm the well-known linear relation between the polarization of a dielectric and the electric field. Dielectric susceptibilities are estimated from the linear relation for four types of dielectric.

  6. Physical Properties of Liquid Terbium Measured by Levitation Techniques

    Institute of Scientific and Technical Information of China (English)

    2007-01-01

    To understand the nature and behavior of rare earth metals in their liquid phases, accurate values of their physical properties are essential.However, to measure their physical properties, the samples should be maintained in liquid phases for prolonged time, and this raises a formidable challenge.This is mainly explained by their high melting temperatures (e.g., 1629 K for Tb), high vapor pressure, and the risk of melt contamination with a crucible or support.An electrostatic levitation furnace alleviated these difficulties and allowed the determination of density, surface tension, and viscosity of several metals above their melting temperature.Here, first, the levitation furnace facility and the noncontact diagnostic procedures were briefly discussed, followed by the explanation of their thermophysical property measurements over wide temperature ranges.The density was obtained using an ultraviolet-based imaging technique that allowed excellent illumination, even at elevated temperatures.Over the 1615 to 1880 K temperature span, the density measurements could be expressed as ρ(T)=7.84×103-0.47 (T-Tm) (kg·m-3) with Tm=1629 K, yielding a volume expansion coefficient α(T) =6.0×10-5 (K-1).In addition, the surface tension and the viscosity could be determined by inducing a drop oscillation to a molten sample.Using this technique, the surface tension data could be expressed as σ(T)=8.93×102-0.10 (T-Tm)(mN·m-1) and those for viscosity as η(T) =0.583 exp [4.1×104/(RT)] (MPa·s) over the 1690 to 1980 K temperature range.

  7. Method and System for Measuring Spinning YarnTension Using Image Measuring Technique

    Institute of Scientific and Technical Information of China (English)

    梅顺齐; 宋志峰; 张智明

    2004-01-01

    A non-contact method and system for measuring spinning yarn tension is developed using an image processing technique and based on the theory of yarn balloon dynamics. The theoretical basis of the measurement is the relationship among yarn tension, balloon shape, and spinning parameters. The yarn tension is determined according to the geometric parameters of the balloon, which are measured from an image of the balloon. The digital image is captured with a CCD sensor, and processed in a computer using a wavelet transform technique. A measuring system is developed, and experiments are carried out. The results show that the proposed non-contact method is effective in the on-line measurement of spinning yarn tension for improving the degree of automation of the spinning machine.

  8. A comparison of forest height prediction from FIA field measurement and LiDAR data via spatial models

    Science.gov (United States)

    Yuzhen Li

    2009-01-01

    Previous studies have shown a high correspondence between tree height measurements acquired from airborne LiDAR and that those measured using conventional field techniques. Though these results are very promising, most of the studies were conducted over small experimental areas and tree height was measured carefully or using expensive instruments in the field, which is...

  9. Investigations And Techniques In Nonperturbative Quantum Field Theory

    CERN Document Server

    Sprague, K B

    1999-01-01

    In Part I, the contributions of the dimension-3 fermion- antifermion and dimension-4 gluon vacuum-condensates to the electromagnetic (em) vertex of a condensing fermion are investigated. These nonperturbative contributions to the em vertex are modeled after perturbative calculations involving the exchange of a single virtual photon between incoming and outgoing fermions. Perturbative contributions to the anomalous magnetic moment of a QED fermion are calculated in terms of vertex correction structure functions evaluated at zero-momentum transfer. The QCD fermion-antifermion and gluon condensate contributions to the em vertex are found analogously using fermion, photon, and gluon propagators, thereby determining the corresponding contributions to the anomalous magnetic moment of a fermion in a vacuum that allows such condensation to occur. Such a correspondence is drawn through the adaptation of techniques used in QCD sum-rule applications. In Part II we exp...

  10. A laser-induced heat flux technique for convective heat transfer measurements in high speed flows

    Science.gov (United States)

    Porro, A. R.; Keith, T. G., Jr.; Hingst, W. R.

    1991-01-01

    A technique is developed to measure the local convective heat transfer coefficient on a model surface in a supersonic flow field. The technique uses a laser to apply a discrete local heat flux at the model test surface, and an infrared camera system determines the local temperature distribution due to the heating. From this temperature distribution and an analysis of the heating process, a local convective heat transfer coefficient is determined. The technique was used to measure the local surface convective heat transfer coefficient distribution on a flat plate at nominal Mach numbers of 2.5, 3.0, 3.5, and 4.0. The flat plate boundary layer initially was laminar and became transitional in the measurement region. The experimentally determined convective heat transfer coefficients were generally higher than the theoretical predictions for flat plate laminar boundary layers. However, the results indicate that this nonintrusive optical measurement technique has the potential to measure surface convective heat transfer coefficients in high-speed flowfields.

  11. Intelligent instruments for process measurement techniques (monitoring of sensors)

    Science.gov (United States)

    Bauer, B.; Hess, H. D.; Kalinski, J. R.; Leisenberg, W.; Marsch, D.

    1984-06-01

    Possibilities to extract redundant information of temperature sensors (resistance thermometers, thermocouples, semiconductor temperature sensors), and to find out which of the suggested redundancies are most suited for self controlled monitoring were investigated. Practical experience with equipment for process measurement techniques shows that sensor failures are five times more frequent than electronic malfunction. For resistance thermometers the measured values of the redundant information source (ac resistance) are too small (relative inductivity change 7 million). The information sources strain gage and propagation of ultrasonic waves are excluded because of physical properties in the sensor materials. Changes in the crystalline structure of thermocouples have the effect that there is no well defined relationship between thermoelectric voltage and the redundant information sources, resistance and coupled current impulses. A correlation of thermovoltage with these redundant values would yield a measurement uncertainty corresponding to more than + or - 50 K. Experiments with negative temperature coefficient sensors show that a failure is proceeded by a change in capacitance of the order of 0.1 pF.

  12. A laser speckle imaging technique for measuring tissue perfusion.

    Science.gov (United States)

    Forrester, Kevin R; Tulip, J; Leonard, C; Stewart, C; Bray, Robert C

    2004-11-01

    Laser Doppler imaging (LDI) has become a standard method for optical measurement of tissue perfusion, but is limited by low resolution and long measurement times. We have developed an analysis technique based on a laser speckle imaging method that generates rapid, high-resolution perfusion images. We have called it laser speckle perfusion imaging (LSPI). This paper investigates LSPI output and compares it to LDI using blood flow models designed to simulate human skin at various levels of pigmentation. Results show that LSPI parameters can be chosen such that the instrumentation exhibits a similar response to changes in red blood cell concentration (0.1%-5%, 200 microL/min) and velocity (0-800 microL/min, 1% concentration) and, given its higher resolution and quicker response time, could provide a significant advantage over LDI for some applications. Differences were observed in the LDI and LSPI response to tissue optical properties. LDI perfusion values increased with increasing tissue absorption, while LSPI perfusion values showed a slight decrease. This dependence is predictable, owing to the perfusion algorithms specific to each instrument, and, if properly compensated for, should not influence each instrument's ability to measure relative changes in tissue perfusion.

  13. New Limits on Extragalactic Magnetic Fields from Rotation Measures

    Science.gov (United States)

    Pshirkov, M. S.; Tinyakov, P. G.; Urban, F. R.

    2016-05-01

    We take advantage of the wealth of rotation measures data contained in the NRAO VLA Sky Survey catalog to derive new, statistically robust, upper limits on the strength of extragalactic magnetic fields. We simulate the extragalactic magnetic field contribution to the rotation measures for a given field strength and correlation length, by assuming that the electron density follows the distribution of Lyman-α clouds. Based on the observation that rotation measures from distant radio sources do not exhibit any trend with redshift, while the extragalactic contribution instead grows with distance, we constrain fields with Jeans' length coherence length to be below 1.7 nG at the 2 σ level, and fields coherent across the entire observable Universe below 0.65 nG. These limits do not depend on the particular origin of these cosmological fields.

  14. The effect of sensor sheltering and averaging techniques on wind measurements at the Shuttle Landing Facility

    Science.gov (United States)

    Merceret, Francis J.

    1995-01-01

    This document presents results of a field study of the effect of sheltering of wind sensors by nearby foliage on the validity of wind measurements at the Space Shuttle Landing Facility (SLF). Standard measurements are made at one second intervals from 30-feet (9.1-m) towers located 500 feet (152 m) from the SLF centerline. The centerline winds are not exactly the same as those measured by the towers. A companion study, Merceret (1995), quantifies the differences as a function of statistics of the observed winds and distance between the measurements and points of interest. This work examines the effect of nearby foliage on the accuracy of the measurements made by any one sensor, and the effects of averaging on interpretation of the measurements. The field program used logarithmically spaced portable wind towers to measure wind speed and direction over a range of conditions as a function of distance from the obstructing foliage. Appropriate statistics were computed. The results suggest that accurate measurements require foliage be cut back to OFCM standards. Analysis of averaging techniques showed that there is no significant difference between vector and scalar averages. Longer averaging periods reduce measurement error but do not otherwise change the measurement in reasonably steady flow regimes. In rapidly changing conditions, shorter averaging periods may be required to capture trends.

  15. [A focused sound field measurement system by LabVIEW].

    Science.gov (United States)

    Jiang, Zhan; Bai, Jingfeng; Yu, Ying

    2014-05-01

    In this paper, according to the requirement of the focused sound field measurement, a focused sound field measurement system was established based on the LabVIEW virtual instrument platform. The system can automatically search the focus position of the sound field, and adjust the scanning path according to the size of the focal region. Three-dimensional sound field scanning time reduced from 888 hours in uniform step to 9.25 hours in variable step. The efficiency of the focused sound field measurement was improved. There is a certain deviation between measurement results and theoretical calculation results. Focal plane--6 dB width difference rate was 3.691%, the beam axis--6 dB length differences rate was 12.937%.

  16. The Synthesis of Structural Responses Using Experimentally Measured Frequency Response Functions and Field Test Data

    Energy Technology Data Exchange (ETDEWEB)

    CAP,JEROME S.; NELSON,CURTIS F.

    2000-11-17

    This paper presents an analysis technique used to generate the structural response at locations not measured during the ejection of a captive-carried store. The ejection shock event is complicated by the fact that forces may be imparted to the store at eight distinct locations. The technique derives forcing functions by combining the initial field test data for a limited number of measurement locations with Frequency Response Functions (FRFs) measured using a traditional modal-type impact (tap) test at the same locations. The derived forcing functions were then used with tap test FRFs measured at additional locations of interest to produce the desired response data.

  17. Dark-field electron holography for the measurement of geometric phase

    Energy Technology Data Exchange (ETDEWEB)

    Hytch, M.J., E-mail: hytch@cemes.fr [CEMES-CNRS and Universite de Toulouse, 29 rue Jeanne Marvig, F-31055 Toulouse (France); Houdellier, F.; Huee, F.; Snoeck, E. [CEMES-CNRS and Universite de Toulouse, 29 rue Jeanne Marvig, F-31055 Toulouse (France)

    2011-07-15

    The genesis, theoretical basis and practical application of the new electron holographic dark-field technique for mapping strain in nanostructures are presented. The development places geometric phase within a unified theoretical framework for phase measurements by electron holography. The total phase of the transmitted and diffracted beams is described as a sum of four contributions: crystalline, electrostatic, magnetic and geometric. Each contribution is outlined briefly and leads to the proposal to measure geometric phase by dark-field electron holography (DFEH). The experimental conditions, phase reconstruction and analysis are detailed for off-axis electron holography using examples from the field of semiconductors. A method for correcting for thickness variations will be proposed and demonstrated using the phase from the corresponding bright-field electron hologram. -- Highlights: {yields} Unified description of phase measurements in electron holography. {yields} Detailed description of dark-field electron holography for geometric phase measurements. {yields} Correction procedure for systematic errors due to thickness variations.

  18. Size measurement of radioactive aerosol particles in intense radiation fields using wire screens and imaging plates

    Energy Technology Data Exchange (ETDEWEB)

    Oki, Yuichi; Tanaka, Toru; Takamiya, Koichi; Ishi, Yoshihiro; UesugI, Tomonori; Kuriyama, Yasutoshi; Sakamoto, Masaaki; Ohtsuki, Tsutomu [Kyoto University Research Reactor Institute, Osaka (Japan); Nitta, Shinnosuke [Graduate School of Engineering, Kyoto University, Kyoto (Japan); Osada, Naoyuki [Advanced Science Research Center, Okayama University, Okayama (Japan)

    2016-09-15

    Very fine radiation-induced aerosol particles are produced in intense radiation fields, such as high-intensity accelerator rooms and containment vessels such as those in the Fukushima Daiichi nuclear power plant (FDNPP). Size measurement of the aerosol particles is very important for understanding the behavior of radioactive aerosols released in the FDNPP accident and radiation safety in high-energy accelerators. A combined technique using wire screens and imaging plates was developed for size measurement of fine radioactive aerosol particles smaller than 100 nm in diameter. This technique was applied to the radiation field of a proton accelerator room, in which radioactive atoms produced in air during machine operation are incorporated into radiation-induced aerosol particles. The size of 11C-bearing aerosol particles was analyzed using the wire screen technique in distinction from other positron emitters in combination with a radioactive decay analysis. The size distribution for 11C-bearing aerosol particles was found to be ca. 70 μm in geometric mean diameter. The size was similar to that for 7Be-bearing particles obtained by a Ge detector measurement, and was slightly larger than the number-based size distribution measured with a scanning mobility particle sizer. The particle size measuring method using wire screens and imaging plates was successfully applied to the fine aerosol particles produced in an intense radiation field of a proton accelerator. This technique is applicable to size measurement of radioactive aerosol particles produced in the intense radiation fields of radiation facilities.

  19. Evaluation of three new laser spectrometer techniques for in-situ carbon monoxide measurements

    Directory of Open Access Journals (Sweden)

    C. Zellweger

    2012-07-01

    Full Text Available Long-term time series of the atmospheric composition are essential for environmental research and thus require compatible, multi-decadal monitoring activities. However, the current data quality objectives of the World Meteorological Organization (WMO for carbon monoxide (CO in the atmosphere are very challenging to meet with the measurement techniques that have been used until recently. During the past few years, new spectroscopic techniques came on the market with promising properties for trace gas analytics. The current study compares three instruments that are recently commercially available (since 2011 with the up to now best available technique (vacuum UV fluorescence and provides a link to previous comparison studies. The instruments were investigated for their performance regarding repeatability, reproducibility, drift, temperature dependence, water vapour interference and linearity. Finally, all instruments were examined during a short measurement campaign to assess their applicability for long-term field measurements. It could be shown that the new techniques provide a considerably better performance compared to previous techniques, although some issues such as temperature influence and cross sensitivities need further attention.

  20. Evaluation of new laser spectrometer techniques for in-situ carbon monoxide measurements

    Science.gov (United States)

    Zellweger, C.; Steinbacher, M.; Buchmann, B.

    2012-10-01

    Long-term time series of the atmospheric composition are essential for environmental research and thus require compatible, multi-decadal monitoring activities. The current data quality objectives of the World Meteorological Organization (WMO) for carbon monoxide (CO) in the atmosphere are very challenging to meet with the measurement techniques that have been used until recently. During the past few years, new spectroscopic techniques came to market with promising properties for trace gas analytics. The current study compares three instruments that have recently become commercially available (since 2011) with the best currently available technique (Vacuum UV Fluorescence) and provides a link to previous comparison studies. The instruments were investigated for their performance regarding repeatability, reproducibility, drift, temperature dependence, water vapour interference and linearity. Finally, all instruments were examined during a short measurement campaign to assess their applicability for long-term field measurements. It could be shown that the new techniques perform considerably better compared to previous techniques, although some issues, such as temperature influence and cross sensitivities, need further attention.

  1. Evaluation of three new laser spectrometer techniques for in-situ carbon monoxide measurements

    Science.gov (United States)

    Zellweger, C.; Steinbacher, M.; Buchmann, B.

    2012-07-01

    Long-term time series of the atmospheric composition are essential for environmental research and thus require compatible, multi-decadal monitoring activities. However, the current data quality objectives of the World Meteorological Organization (WMO) for carbon monoxide (CO) in the atmosphere are very challenging to meet with the measurement techniques that have been used until recently. During the past few years, new spectroscopic techniques came on the market with promising properties for trace gas analytics. The current study compares three instruments that are recently commercially available (since 2011) with the up to now best available technique (vacuum UV fluorescence) and provides a link to previous comparison studies. The instruments were investigated for their performance regarding repeatability, reproducibility, drift, temperature dependence, water vapour interference and linearity. Finally, all instruments were examined during a short measurement campaign to assess their applicability for long-term field measurements. It could be shown that the new techniques provide a considerably better performance compared to previous techniques, although some issues such as temperature influence and cross sensitivities need further attention.

  2. Evaluation of new laser spectrometer techniques for in-situ carbon monoxide measurements

    Directory of Open Access Journals (Sweden)

    C. Zellweger

    2012-10-01

    Full Text Available Long-term time series of the atmospheric composition are essential for environmental research and thus require compatible, multi-decadal monitoring activities. The current data quality objectives of the World Meteorological Organization (WMO for carbon monoxide (CO in the atmosphere are very challenging to meet with the measurement techniques that have been used until recently. During the past few years, new spectroscopic techniques came to market with promising properties for trace gas analytics. The current study compares three instruments that have recently become commercially available (since 2011 with the best currently available technique (Vacuum UV Fluorescence and provides a link to previous comparison studies. The instruments were investigated for their performance regarding repeatability, reproducibility, drift, temperature dependence, water vapour interference and linearity. Finally, all instruments were examined during a short measurement campaign to assess their applicability for long-term field measurements. It could be shown that the new techniques perform considerably better compared to previous techniques, although some issues, such as temperature influence and cross sensitivities, need further attention.

  3. Breast cancer regional radiation fields for supraclavicular and axillary lymph node treatment: is a posterior axillary boost field technique optimal?

    Science.gov (United States)

    Wang, Xiaochun; Yu, Tse Kuan; Salehpour, Mohammad; Zhang, Sean X; Sun, Tzouh Liang; Buchholz, Thomas A

    2009-05-01

    To assess whether using an anterior oblique supraclavicular (SCV) field with a posterior axillary boost (PAB) field is an optimal technique for targeting axillary (AX) lymph nodes compared with two computed tomography (CT)-based techniques: (1) an SCV field with an anterior boost field and (2) intensity-modulated radiotherapy (IMRT). Ten patients with CT simulation data treated with postmastectomy radiation that included an SCV field were selected for the study. Supraclavicular nodes and AX Level I-III nodes within the SCV field were contoured and defined as the treatment target. Plans using the three techniques were generated and evaluated for each patient. The anterior axillary boost field and IMRT resulted in superior dose coverage compared with PAB. Namely, treatment volumes that received 105%, 80%, and 30% of prescribed dose for IMRT plans were significantly less than those for the anterior axillary boost plans, which were significantly less than PAB. For PAB and anterior axillary boost plans, there was a linear correlation between treatment volume receiving 105% of prescribed dose and maximum target depth. Furthermore, the IMRT technique resulted in better lung sparing and dose conformity to the target than anterior axillary boost, which again was significantly better than PAB. The maximum cord dose for IMRT was small, but higher than for the other two techniques. More monitor units were required to deliver the IMRT plan than the PAB plan, which was more than the anterior axillary boost plan. The PAB technique is not optimal for treatment of AX lymph nodes in an SCV field. We conclude that CT treatment planning with dose optimization around delineated target volumes should become standard for radiation treatments of supraclavicular and AX lymph nodes.

  4. Magnetic field measurements of JT-60SA CS model coil

    Energy Technology Data Exchange (ETDEWEB)

    Obana, Tetsuhiro, E-mail: obana.tetsuhiro@LHD.nifs.ac.jp [National Institute for Fusion Science, 322-6 Oroshi, Toki, Gifu 509-5292 (Japan); Takahata, Kazuya; Hamaguchi, Shinji; Chikaraishi, Hirotaka; Mito, Toshiyuki; Imagawa, Shinsaku [National Institute for Fusion Science, 322-6 Oroshi, Toki, Gifu 509-5292 (Japan); Kizu, Kaname; Murakami, Haruyuki; Natsume, Kyohei; Yoshida, Kiyoshi [Japan Atomic Energy Agency, 801-1 Mukoyama, Naka, Ibaraki 311-0193 (Japan)

    2015-01-15

    Highlights: • Magnetic fields of the JT-60SA CS model coil were measured. • While the coil current was held constant at 20 kA, magnetic fields varied slightly with several different long time constants. • We investigated coils consisting of CIC conductors and having long time constants. - Abstract: In a cold test of the JT-60SA CS model coil, which has a quad-pancake configuration consisting of a Nb{sub 3}Sn cable-in-conduit (CIC) conductor, magnetic fields were measured using Hall sensors. For a holding coil current of 20 kA, measured magnetic fields varied slightly with long time constants in the range 17–571 s, which was much longer than the time constant derived from a measurement using a short straight sample. To validate the measurements, the magnetic fields of the model coil were calculated using a computational model representing the positions of Nb{sub 3}Sn strands inside the CIC conductor. The calculated results were in good agreement with the measurements. Consequently, the validity of the magnetic field measurements was confirmed. Next, we investigated other coils consisting of CIC conductors and having long time constants. The only commonality among the coils was the use of CIC conductors. At present, there is no obvious way to prevent generation of such magnetic-field variations with long time constants.

  5. Stress Measurement with an Improved Hollow Inclusion Technique In Jinchuan Nickel Mine

    Institute of Scientific and Technical Information of China (English)

    2000-01-01

    Borehole overcoring stress measurement with an improved hollow inclusion technique was carried out at 10 points on 3 levels in Jinchuan nickel mine which is situated in north-west of China. Through the measurement, 3-D in situ stress state at the measuring points and distribution characteristics of the stress field in the mine were obtained. The stress state in Jinchuan mine is dominated by the horizontal tectonic stress field. The maximum principal stress is horizontal which is about twice the weight of the overburden and its orientation is approximately vertical to the regional tectonic line. The difference between two horizontal principal stresses is quite large which is an important reason to cause failure of underground excavations.

  6. Blood pressure measurement in hemodialysis: The importance of the measurement technique.

    Science.gov (United States)

    Kubrusly, M; de Oliveira, Claudia Maria Costa; Silva, R P; Pinheiro, M A; Rocha, M B C; Magalhães, R M

    2016-03-01

    Systemic arterial hypertension contributes to the high cardiovascular morbidity in hemodialysis (HD) patients, but the accuracy of blood pressure (BP) measurement in this population has not been well studied. To evaluate the agreement between BP measurement using the routine measurement technique (usual method) and the technique recommended by the VII Joint (standard method). This cross-sectional study enrolled 124 patients in a single center who had undergone dialysis for more than three months and were 18 years of age or older. The BP was verified at the start of dialysis by the nursing team (usual method) and by the researchers (standard method). The agreement between the systolic and diastolic BP (SBP and DBP) measurements was tested by the Bland-Altman analysis. A difference in BP measurement higher than ±5 mm Hg was considered clinically significant. The studied group had a mean age of 53.2 years. The average difference between routine and standard BP measurement was -6 mm Hg for SBP (limits of agreement: -40.1-28 mm Hg; P measured by both methods was observed in 69.4% of the patients for SBP and in 61.3% for DBP. The disagreement between the results of different BP measurement methods in HD patients was significant and the BP was underestimated using the usual BP method. BP measurement standardization should be encouraged to avoid errors in diagnosis and therapy.

  7. High sensitivity probe absorption technique for time-of-flight measurements on cold atoms

    Indian Academy of Sciences (India)

    A K Mohapatra; C S Unnikrishnan

    2006-06-01

    We report on a phase-sensitive probe absorption technique with high sensitivity, capable of detecting a few hundred ultra-cold atoms in flight in an observation time of a few milliseconds. The large signal-to-noise ratio achieved is sufficient for reliable measurements on low intensity beams of cold atoms. We demonstrate the high sensitivity and figure of merit of the simple method by measuring the time-of-flight of atoms moving upwards from a magneto-optical trap released in the gravitational field.

  8. Measurement of the Waveguide Near-field Optical Spot

    Institute of Scientific and Technical Information of China (English)

    2003-01-01

    The characteristic of near-field spots is analyzed.The size of the near field and the heat response time of the hybrid record medium to overcome super paramagnetic effect are calculated based on the heat transfer theory. A novel measuring method for the diameter of near-field recording spot is also presented. Since the grain of the recording media is tiny enough,near-field optical lithography can be accomplished with the aid of atomic force microscope (AFM).The diameter of near-field recording spot can be obtained by specifically designed computer.So the relationship between the near-field recording spot diameter and the probe size of near-field recording system, the near field recording distance coupling between head and disc can be got.

  9. A new technique for the solution of references problem in oil pollution measurement by UVF technique

    Directory of Open Access Journals (Sweden)

    Kasım Cemal Güven

    2016-09-01

    Full Text Available In this work, the problems of references used for oil pollution measurement by UVF method were discussed. The main problem of this method is that the origin of the reference for pollutant oil is unknown. The proposed solution for this problem was based on sea water sample which was taken from contaminated area, extracted by DCM, the organic phase was distilled, its calibration curve was plotted with this residue oil and measurement was made on its equation. The oil pollution results for the sea water of K0 station by using this equation for 2013 was 15.21 mg/L and for 2014 15.25 mg/L. for the same samples determination of oil pollution by using crude oil references varies between 0.11 and 1.15 various crude oils and using chrysene reference 0.11-0.19 mg/L. These results show that pollution level varied depending on references used. The proposed method more realistically determines the oil pollution level. The proposed technique is the first for oil pollution measurement by UVF.

  10. ‘Inverted Y’ field radiotherapy planning with multi-leaf collimator: A single isocentric technique using multiple fields

    Directory of Open Access Journals (Sweden)

    Puja Sahai

    2015-01-01

    Full Text Available The purpose of our study is to describe a planning technique using multi-leaf collimator and asymmetric fields for irradiating an ‘inverted Y’ shaped geometry in a patient with testicular seminoma. The entire target area covering the para-aortic, pelvic, and inguinal nodal regions was split into three fields. Single isocenter half-beam block technique was employed. The fields were planned with antero-posterior and postero-anterior portals with a differential weightage. The dose was prescribed at the respective reference points of the fields. A uniform dose distribution for the entire portal was achieved without any under- or over-dosing at the field junctions.  

  11. Measurement techniques for in situ stresses around underground constructions in a deep clay formation

    Directory of Open Access Journals (Sweden)

    Li X.L.

    2010-06-01

    Full Text Available Disposal in deep underground geological formations is internationally recognized as the most viable option for the long-term management of high-level radioactive waste. In Belgium, the Boom clay formation is extensively studied in this context, in particular at the 225 m deep HADES Underground Research Facility in Mol. A cost-effective design of deep underground structures requires an accurate assessment of the in situ stresses; a good estimation of these stresses is also essential when interpreting in situ experiments regarding the hydro-mechanical behaviour of the host formation. Different measurement techniques are available to provide data on the stress evolution and other mechanical properties of the geological formation. The measurement can be direct (measurement of total pressure, or it can be an indirect technique, deriving the stress from related quantities such as strain (changes in structural members. Most total stress measurements are performed through permanently installed sensors; also once-only measurements are performed through specific methods (e.g. pressuremeter. Direct measurement of the stress state is challenging due to the complex mechanical behaviour of the clay, and the fact that the sensor installation inevitably disturbs the original stress field. This paper describes ways to deal with these problems and presents the results obtained using different techniques at HADES.

  12. Measuring Oscillatory Velocity Fields Due to Swimming Algae

    CERN Document Server

    Guasto, Jeffrey S; Gollub, J P

    2010-01-01

    In this fluid dynamics video, we present the first time-resolved measurements of the oscillatory velocity field induced by swimming unicellular microorganisms. Confinement of the green alga C. reinhardtii in stabilized thin liquid films allows simultaneous tracking of cells and tracer particles. The measured velocity field reveals complex time-dependent flow structures, and scales inversely with distance. The instantaneous mechanical power generated by the cells is measured from the velocity fields and peaks at 15 fW. The dissipation per cycle is more than four times what steady swimming would require.

  13. Electro-optic probe measurements of electric fields in plasmas

    Science.gov (United States)

    Nishiura, M.; Yoshida, Z.; Mushiake, T.; Kawazura, Y.; Osawa, R.; Fujinami, K.; Yano, Y.; Saitoh, H.; Yamasaki, M.; Kashyap, A.; Takahashi, N.; Nakatsuka, M.; Fukuyama, A.

    2017-02-01

    The direct measurements of high-frequency electric fields in a plasma bring about significant advances in the physics and engineering of various waves. We have developed an electro-optic sensor system based on the Pockels effect. Since the signal is transmitted through an optical fiber, the system has high tolerance for electromagnetic noises. To demonstrate its applicability to plasma experiments, we report the first result of measurement of the ion-cyclotron wave excited in the RT-1 magnetosphere device. This study compares the results of experimental field measurements with simulation results of electric fields in plasmas.

  14. Magnetic rotation imaging method to measure the geomagnetic field

    Institute of Scientific and Technical Information of China (English)

    2008-01-01

    A new imaging method for measuring the geomagnetic field based on the magnetic rotation effect is put forward. With the help of polarization property of the sunlight reflected from the ground and the magnetic rotation of the atmosphere, the geomagnetic field can be measured by an optical system installed on a satellite. According to its principle, the three-dimensional image of the geomagnetic field can be obtained. The measuring speed of this method is very high, and there is no blind spot and distortion. In this paper, the principle of this method is presented, and some key problems are discussed.

  15. Direct analysis of dispersive wave fields from near-field pressure measurements

    NARCIS (Netherlands)

    Horchens, L.

    2011-01-01

    Flexural waves play a significant role for the radiation of sound from plates. The analysis of flexural wave fields enables the detection of sources and transmission paths in plate-like structures. The measurement of these wave fields can be carried out indirectly by means of near-field acoustic hol

  16. Dynamics measured in a non-Archimedean field

    NARCIS (Netherlands)

    Kool, J.

    2012-01-01

    We study dynamical systems using measures taking values in a non-Archimedean field. The underlying space for such measure is a zero-dimensional topological space. In this paper we elaborate on the natural translation of several notions, e.g., probability measures, isomorphic transformations, entropy

  17. Techniques of body composition assessment: a review of laboratory and field methods.

    Science.gov (United States)

    Wagner, D R; Heyward, V H

    1999-06-01

    Body composition is one of the major health-related components of fitness. Thus, it is important for health and fitness professionals to have a general understanding of the most commonly used techniques for assessing body composition. This review presents the developmental background and underlying principles and theory of four laboratory (hydrodensitometry, air displacement plethysmography, isotope dilution, and dual-energy x-ray absorptiometry) and four field (bioelectrical impedance analysis, near-infrared interactance, skinfolds, and anthropometry) methods of body composition assessment. In addition to a description of the methods, the validity, and reliability, strengths, and limitations of each measurement tool are examined. Highlights of the laboratory methods include the relatively new Bod Pod air displacement device, which is a promising assessment tool more convenient than hydrodensitometry but still lacking substantial validity testing and the ability of dual-energy x-ray absorptiometry to measure regional composition making it an attractive method for clinicians. Advancements in segmental and multifrequency bioelectrical impedance for compartmental analysis have enhanced the value of this field method, but research continues to show that commercially available near-infrared interactance units are invalid. With this knowledge, the clinician and researcher should be able to make an informed decision regarding the most appropriate measurement device for their body composition assessments.

  18. Project 8: Using Radio-Frequency Techniques to Measure Neutrino Mass

    CERN Document Server

    Oblath, N S

    2013-01-01

    The Project 8 experiment aims to measure the neutrino mass using tritium beta decays. Beta-decay electron energies will be measured with a novel technique: as the electrons travel in a uniform magnetic field their cyclotron radiation will be detected. The frequency of each electron's cyclotron radiation is inversely proportional to its total relativistic energy; therefore, by observing the cyclotron radiation we can make a precise measurement of the electron energies. The advantages of this technique include scalability, excellent energy resolution, and low backgrounds. The collaboration is using a prototype experiment to study the feasibility of the technique with a $^{83m}$Kr source. Demonstrating the ability to see the 17.8 keV and 30.2 keV conversion electrons from $^{83m}$Kr will show that it may be possible to measure tritium beta-decay electron energies ($Q \\approx 18.6$ keV) with their cyclotron radiation. Progress on the prototype, analysis and signal-extraction techniques, and an estimate of the pot...

  19. Trace element measurement in Saliva by NAA and PIXE techniques

    Energy Technology Data Exchange (ETDEWEB)

    Hamidian, M.R.; Vahid Golpayegani, M.; Shojai, S. (Shahid Beheshti Medical Science Univ., Shemiran, Tehran (Iran, Islamic Republic of))

    1993-01-01

    The activity of salivary glands and the chemical and physical properties of saliva, especially in some illnesses in which the activity of salivary glands and the chemical and physical properties alter, sometimes have severe effects on sedimentation and tooth decay. Long-standing investigations have shown the relationship between salivary gland activity and saliva composition in dental carries. Many modern techniques have been employed to measure important elements in saliva. The major elements in saliva include sodium, potassium, calcium, magnesium, chlorine, phosphorus, iodine, and fluorine. It should be pointed out that the amount of minerals changes when the diet changes. The major constituent of saliva is water with a density of 1.007 g/cm[sup 3] in which 0.6% is solid, 0.3% organic material and 0.3% inorganic material. In addition to other effects, the acidity (pH) of saliva has a strong effect on tooth sedimentation. Type of work, degree of stress, and mental condition affect salivary gland activity. When the acidity of salivary fluid in the mouth and consequently over the teeth drops, sedimentation increases. In this paper, the results of trace element measurement in saliva are presented.

  20. Image based measurement techniques for aircraft propeller flow diagnostics: Propeller slipstream investigations at high-lift conditions and thrust reverse

    NARCIS (Netherlands)

    Roosenboom, E.W.M.

    2011-01-01

    The aim of the thesis is to measure the propeller slipstream properties (velocity and vorticity) and to assess the unsteady and instantaneous behavior of the propeller flow field at high disk loadings, zero thrust and thrust reverse using the image based measurement techniques. Along with its implem