WorldWideScience

Sample records for field configuration measurement

  1. Internal magnetic field measurement on C-2 field-reversed configuration plasmas.

    Science.gov (United States)

    Gota, H; Thompson, M C; Knapp, K; Van Drie, A D; Deng, B H; Mendoza, R; Guo, H Y; Tuszewski, M

    2012-10-01

    A long-lived field-reversed configuration (FRC) plasma has been produced in the C-2 device by dynamically colliding and merging two oppositely directed, highly supersonic compact toroids (CTs). The reversed-field structure of the translated CTs and final merged-FRC state have been directly verified by probing the internal magnetic field structure using a multi-channel magnetic probe array near the midplane of the C-2 confinement chamber. Each of the two translated CTs exhibits significant toroidal fields (B(t)) with opposite helicity, and a relatively large B(t) remains inside the separatrix after merging.

  2. Probe measurements of the three-dimensional magnetic field structure in a rotating magnetic field sustained field-reversed configuration

    Science.gov (United States)

    Velas, K. M.; Milroy, R. D.

    2014-01-01

    A translatable three-axis probe was constructed and installed on the translation, confinement, and sustainment upgrade (TCSU) experiment. With ninety windings, the probe can simultaneously measure Br, Bθ, and Bz at 30 radial positions, and can be placed at any desired axial position within the field reversed configuration (FRC) confinement chamber. Positioning the probe at multiple axial positions and taking multiple repeatable shots allows for a full r-z map of the magnetic field. Measurements were made for odd-parity rotating magnetic field (RMF) antennas and even-parity RMF. The steady state data from applying a 10 kHz low pass filter used in conjunction with data at the RMF frequency yields a map of the full 3D rotating field structure. Comparisons will be made to the 3D magnetic structure predicted by NIMROD simulations, with parameters adjusted to match that of the TCSU experiments. The probe provides sufficient data to utilize a Maxwell stress tensor approach to directly measure the torque applied to the FRC's electrons, which combined with a resistive torque model, yields an estimate of the average FRC resistivity.

  3. A configurable component-based software system for magnetic field measurements

    Energy Technology Data Exchange (ETDEWEB)

    Nogiec, J.M.; DiMarco, J.; Kotelnikov, S.; Trombly-Freytag, K.; Walbridge, D.; Tartaglia, M.; /Fermilab

    2005-09-01

    A new software system to test accelerator magnets has been developed at Fermilab. The magnetic measurement technique involved employs a single stretched wire to measure alignment parameters and magnetic field strength. The software for the system is built on top of a flexible component-based framework, which allows for easy reconfiguration and runtime modification. Various user interface, data acquisition, analysis, and data persistence components can be configured to form different measurement systems that are tailored to specific requirements (e.g., involving magnet type or test stand). The system can also be configured with various measurement sequences or tests, each of them controlled by a dedicated script. It is capable of working interactively as well as executing a preselected sequence of tests. Each test can be parameterized to fit the specific magnet type or test stand requirements. The system has been designed with portability in mind and is capable of working on various platforms, such as Linux, Solaris, and Windows. It can be configured to use a local data acquisition subsystem or a remote data acquisition computer, such as a VME processor running VxWorks. All hardware-oriented components have been developed with a simulation option that allows for running and testing measurements in the absence of data acquisition hardware.

  4. Multi-channel Doppler backscattering measurements in the C-2 field reversed configuration

    Energy Technology Data Exchange (ETDEWEB)

    Schmitz, L., E-mail: lschmitz@ucla.edu; Peebles, W. A. [Department of Physics and Astronomy, University of California Los Angeles, Los Angeles, California 90095 (United States); Ruskov, E. [Department of Physics and Astronomy, University of California, Irvine, Irvine, California 92697 (United States); Deng, B. H.; Gota, H.; Gupta, D.; Tuszewski, M.; Douglass, J.; Binderbauer, M.; Tajima, T. [Tri Alpha Energy, Inc., P.O. Box 7010, Rancho Santa Margarita, California 92688 (United States)

    2014-11-15

    A versatile heterodyne Doppler Backscattering (DBS) system is used to measure density fluctuation levels (in the wavenumber range kρ{sub s} ≤ 50), and the toroidal E × B flow velocity in the C-2 Field-Reversed Configuration (FRC). Six tunable frequencies in three waveguide bands (26 GHz ≤ f ≤ 90 GHz) are launched using monostatic beam optics, via a quasi-optical beam combiner/polarizer and an adjustable parabolic focusing mirror (inside the vacuum enclosure) achieving Gaussian beam spot sizes of 3–5.5 cm at the X/O-mode cutoff. The DBS system covers plasma densities of 0.8 × 10{sup 13} ≤ n{sub e} ≤ 1 × 10{sup 14} cm{sup −3}, and provides access to the FRC core (up to the field null) and across the FRC separatrix into the scrape-off layer plasma.

  5. Ion rotational velocity of a field-reversed configuration plasma measured by neutral beam probe spectroscopy

    Energy Technology Data Exchange (ETDEWEB)

    Ito, Y.; Tanjyo, M.; Ohi, S.; Goto, S.; Ishimura, T.

    1987-01-01

    The ion rotational angular velocity ..cap omega.. and the ion temperature T/sub i/ of a translated field-reversed configuration (FRC) plasma are measured using neutral beam probe spectroscopy. The value of ..cap omega.. is --(1.0--1.2) x ..cap omega..* at the onset time of the n = 2 rotational instability, where ..cap omega..* is the ion diamagnetic frequency for a rigid-rotor equilibrium. The ion rotational direction is the same as the ion diamagnetic direction. The value of ..cap omega.. is smaller than the angular frequency ..omega../sub re/ of the n = 2 instability, which can yield experimental evidence of the ion kinetic effects on the n = 2 instability in the FRC plasma. When the octupole field is applied to the plasma in order to suppress the n = 2 deformation, ..cap omega.. is slightly reduced. The ion temperature T/sub i/ is --70 eV at the onset time of the n = 2 instability.

  6. Multi-channel Doppler backscattering measurements in the C-2 field reversed configuration.

    Science.gov (United States)

    Schmitz, L; Ruskov, E; Deng, B H; Gota, H; Gupta, D; Tuszewski, M; Douglass, J; Peebles, W A; Binderbauer, M; Tajima, T

    2014-11-01

    A versatile heterodyne Doppler Backscattering (DBS) system is used to measure density fluctuation levels (in the wavenumber range kρs ≤ 50), and the toroidal E × B flow velocity in the C-2 Field-Reversed Configuration (FRC). Six tunable frequencies in three waveguide bands (26 GHz ≤ f ≤ 90 GHz) are launched using monostatic beam optics, via a quasi-optical beam combiner/polarizer and an adjustable parabolic focusing mirror (inside the vacuum enclosure) achieving Gaussian beam spot sizes of 3-5.5 cm at the X/O-mode cutoff. The DBS system covers plasma densities of 0.8 × 10(13) ≤ ne ≤ 1 × 10(14) cm(-3), and provides access to the FRC core (up to the field null) and across the FRC separatrix into the scrape-off layer plasma.

  7. Measuring the performance of business model configurations: A field study from the medico tech industry

    DEFF Research Database (Denmark)

    Thomsen, Peter; Nielsen, Christian; Lund, Morten

    Purpose – This study suggests applying the lenses of Activity Systems Theory and Representation Theory in relation to the study of business models. It examines the link between the 71 business model configurations identified by Taran et al. (2016) and performance measures through the mechanisms...... ensure a link to value creation. Originality/value – Based on the understanding of value creation from the concept of business models, benchmarking of corporate performance is proposed as an agent for validating business models configurations and related KPIs....... of value drivers. Design/methodology/approach – An explorative case study of 80 case companies is conducted as a basis for this paper. From these cases, 19 distinct business model configurations are identified and the present study focuses on the 10 configurations that have more than a single datapoint...

  8. Measurements accounting for the impediment of ion spin-up in rotating magnetic field driven field reversed configurations

    Energy Technology Data Exchange (ETDEWEB)

    Deards, C. L. [Lockheed Martin, 1011 Lockheed Way, Palmdale, California 93599 (United States); Hoffman, A. L.; Steinhauer, L. C. [Redmond Plasma Physics Laboratory, University of Washington, 14700 NE 95th Street, Suite 100, Redmond, Washington 98052 (United States)

    2011-11-15

    Improved vacuum hygiene, wall conditioning, and reduced recycling in the rotating magnetic field (RMF) driven translation, confinement, and sustainment-upgrade (TCSU) field reversed configuration experiment have made possible a more accurate assessment of the forces affecting ion spin-up. This issue is critical in plasmas sustained by RMFs, such as TCSU since ion spin-up can substantially reduce or cancel the RMF current drive effect. Several diagnostics are brought to bear, including a 3-axis translatable magnetic probe allowing the first experimental measurement of the end shorting effect. These results show that the ion rotation is determined by a balance between electron-ion friction, the end shorting effect, and ion drag against neutrals.

  9. Measurements accounting for the impediment of ion spin-up in rotating magnetic field driven field reversed configurations

    Science.gov (United States)

    Deards, C. L.; Hoffman, A. L.; Steinhauer, L. C.

    2011-11-01

    Improved vacuum hygiene, wall conditioning, and reduced recycling in the rotating magnetic field (RMF) driven translation, confinement, and sustainment-upgrade (TCSU) field reversed configuration experiment have made possible a more accurate assessment of the forces affecting ion spin-up. This issue is critical in plasmas sustained by RMFs, such as TCSU since ion spin-up can substantially reduce or cancel the RMF current drive effect. Several diagnostics are brought to bear, including a 3-axis translatable magnetic probe allowing the first experimental measurement of the end shorting effect. These results show that the ion rotation is determined by a balance between electron-ion friction, the end shorting effect, and ion drag against neutrals.

  10. A method to measure specific absorption rate of nanoparticles in colloidal suspension using different configurations of radio-frequency fields

    Science.gov (United States)

    Ketharnath, Dhivya; Pande, Rohit; Xie, Leiming; Srinivasan, Srimeenakshi; Godin, Biana; Wosik, Jarek

    2012-08-01

    We report a method for characterization of the efficiency of radio-frequency (rf) heating of nanoparticles (NPs) suspended in an aqueous medium. Measurements were carried out for water suspended 5 nm superparamagnetic iron-oxide NPs with 30 nm dextran matrix for three different configurations of rf electric and magnetic fields. A 30 MHz high-Q resonator was designed to measure samples placed inside a parallel plate capacitor and solenoid coil with or without an rf electric field shield. All components of rf losses were analyzed and rf electric and magnetic field induced heating of NPs and the dispersion medium was determined and discussed.

  11. Investigation of the Three-Dimensional Structure of a Rotating Magnetic Field Driven Field-Reversed Configuration using Internal Magnetic Field Measurements

    Science.gov (United States)

    Velas, Katherine M.

    The Translation, Confinement, Sustainment Upgrade device (TCSU) used a rotating magnetic field (RMF) to form and sustain plasma in a field-reversed configuration (FRC). The physics of RMF current drive can be modeled in terms of the torque acting on the FRC. A fully translatable three-axis internal magnetic probe was built and used to generate a full r-z map of the magnetic field in the FRC and open field line region. Probe measurements are used to calculate the torques acting on the FRC formed using even-parity and odd-parity RMF antenna configurations. Odd-parity current drive was found to be more efficient and yields a plasma with lower resistivity than in even-parity current drive. An extrapolation method was developed to generate 3D magnetic field line plots which show that unlike in even-parity, field lines in odd-parity sustained FRCs make multiple transits of the FRC. Analysis using the three-axis probe data has greatly expanded our understanding of the physics of RMF driven FRCs.

  12. Jet outflow and open field line measurements on the C-2U advanced beam-driven field-reversed configuration plasma experiment

    Science.gov (United States)

    Sheftman, D.; Gupta, D.; Roche, T.; Thompson, M. C.; Giammanco, F.; Conti, F.; Marsili, P.; Moreno, C. D.

    2016-11-01

    Knowledge and control of the axial outflow of plasma particles and energy along open-magnetic-field lines are of crucial importance to the stability and longevity of the advanced beam-driven field-reversed configuration plasma. An overview of the diagnostic methods used to perform measurements on the open field line plasma on C-2U is presented, including passive Doppler impurity spectroscopy, microwave interferometry, and triple Langmuir probe measurements. Results of these measurements provide the jet ion temperature and axial velocity, electron density, and high frequency density fluctuations.

  13. Electron density measurements of a field-reversed configuration plasma using a novel compact ultrastable second-harmonic interferometer

    Energy Technology Data Exchange (ETDEWEB)

    Brandi, F.; Giammanco, F. [Department of Physics, University of Pisa, Largo B. Pontecorvo 3, 56127 Pisa (Italy); Harris, W. S.; Roche, T.; Trask, E.; Wessel, F. J. [Department of Physics and Astronomy, University of California, Irvine, California 92697 (United States)

    2009-11-15

    A compact high-sensitivity second-harmonic interferometer for line-integrated electron density measurements on a large plasma machine is presented. The device is based on a fiber coupled near-infrared continuous-wave Nd:YAG laser and is remotely controlled. The performances of the instrument are tested on the Irvine field-reversed configuration machine, and a sensitivity of few 10{sup 14} cm{sup -2} in measuring line integrated electron density is demonstrated with a time resolution of a few microseconds. The interferometer is self calibrated, has an impressive stability, and it does not require any further alignment after proper installation. These features make this device a real turn-key system suitable for electron density measurement in large plasma machines.

  14. Fluorometer with a quartz-rod waveguide-integrating sphere configuration to measure evanescent-field luminescence

    Science.gov (United States)

    A fluorometer was designed to measure evanescent-field luminescence. A quartz-rod waveguide (d = 2 mm) was installed coaxally inside a cylindrical flow-through cell (id = 2.3 mm, od = 6.3 mm, l = 116 mm). An excitation beam from a UV LED or a miniature xenon flashlamp was focused by a ball lens and ...

  15. The configuration of the Brazilian scientific field

    Directory of Open Access Journals (Sweden)

    RITA B. BARATA

    2014-03-01

    Full Text Available This article describes the configuration of the scientific field in Brazil, characterizing the scientific communities in every major area of knowledge in terms of installed capacity, ability to train new researchers, and capacity for academic production. Empirical data from several sources of information are used to characterize the different communities. Articulating the theoretical contributions of Pierre Bourdieu, Ludwik Fleck, and Thomas Kuhn, the following types of capital are analyzed for each community: social capital (scientific prestige, symbolic capital (dominant paradigm, political capital (leadership in S & T policy, and economic capital (resources. Scientific prestige is analyzed by taking into account the volume of production, activity index, citations, and other indicators. To characterize symbolic capital, the dominant paradigms that distinguish the natural sciences, the humanities, applied sciences, and technology development are analyzed theoretically. Political capital is measured by presidency in one of the main agencies in the S & T national system, and research resources and fellowships define the economic capital. The article discusses the composition of these different types of capital and their correspondence to structural capacities in various communities with the aim of describing the configuration of the Brazilian scientific field.

  16. The configuration of the Brazilian scientific field.

    Science.gov (United States)

    Barata, Rita B; Aragão, Erika; de Sousa, Luis E P Fernandes; Santana, Taris M; Barreto, Mauricio L

    2014-03-01

    This article describes the configuration of the scientific field in Brazil, characterizing the scientific communities in every major area of knowledge in terms of installed capacity, ability to train new researchers, and capacity for academic production. Empirical data from several sources of information are used to characterize the different communities. Articulating the theoretical contributions of Pierre Bourdieu, Ludwik Fleck, and Thomas Kuhn, the following types of capital are analyzed for each community: social capital (scientific prestige), symbolic capital (dominant paradigm), political capital (leadership in S & T policy), and economic capital (resources). Scientific prestige is analyzed by taking into account the volume of production, activity index, citations, and other indicators. To characterize symbolic capital, the dominant paradigms that distinguish the natural sciences, the humanities, applied sciences, and technology development are analyzed theoretically. Political capital is measured by presidency in one of the main agencies in the S & T national system, and research resources and fellowships define the economic capital. The article discusses the composition of these different types of capital and their correspondence to structural capacities in various communities with the aim of describing the configuration of the Brazilian scientific field.

  17. Improved density profile measurements in the C-2U advanced beam-driven Field-Reversed Configuration (FRC) plasmas

    Science.gov (United States)

    Beall, M.; Deng, B. H.; Gota, H.

    2016-11-01

    In the prior C-2 experiment, electron density was measured using a two-color 6-chord CO2/HeNe interferometer. Analysis shows that high-frequency common mode phase noise can be reduced by a factor of 3 by constructing a reference chord. In the system upgrade from C-2 to C-2U a 4-chord far-infrared laser interferometer was developed, which demonstrated superior sensitivity (1 × 1016 m-2 at >1 MHz bandwidth) and solved the under spatial sampling issue of the C-2 interferometer system. Improved density-profile measurement results are presented in this paper, including evidence of fast-ion modified density profile and stabilization of the n = 1 plasma wobble mode.

  18. Field Measurements

    CERN Document Server

    Bottura, L

    2004-01-01

    The measurement of the magnetic field is often the final verification of the complex design and fabrication process of a magnetic system. In several cases, when seeking high accuracy, the measurement technique and its realization can result in a considerable effort. This note describes most used measurement techniques, such as nuclear magnetic resonance, fluxmeters and Hall generators, and their typical range of application. In addition some of less commonly used techniques, such as magneto-optical, SQUIDs, or particle beams methods, are listed.

  19. A high performance field-reversed configuration

    Energy Technology Data Exchange (ETDEWEB)

    Binderbauer, M. W.; Tajima, T.; Steinhauer, L. C.; Garate, E.; Tuszewski, M.; Smirnov, A.; Gota, H.; Barnes, D.; Deng, B. H.; Thompson, M. C.; Trask, E.; Yang, X.; Putvinski, S.; Rostoker, N.; Andow, R.; Aefsky, S.; Bolte, N.; Bui, D. Q.; Ceccherini, F.; Clary, R. [Tri Alpha Energy, Inc., P.O. Box 7010, Rancho Santa Margarita, California 92688 (United States); and others

    2015-05-15

    Conventional field-reversed configurations (FRCs), high-beta, prolate compact toroids embedded in poloidal magnetic fields, face notable stability and confinement concerns. These can be ameliorated by various control techniques, such as introducing a significant fast ion population. Indeed, adding neutral beam injection into the FRC over the past half-decade has contributed to striking improvements in confinement and stability. Further, the addition of electrically biased plasma guns at the ends, magnetic end plugs, and advanced surface conditioning led to dramatic reductions in turbulence-driven losses and greatly improved stability. Together, these enabled the build-up of a well-confined and dominant fast-ion population. Under such conditions, highly reproducible, macroscopically stable hot FRCs (with total plasma temperature of ∼1 keV) with record lifetimes were achieved. These accomplishments point to the prospect of advanced, beam-driven FRCs as an intriguing path toward fusion reactors. This paper reviews key results and presents context for further interpretation.

  20. C-2-Upgrade Field Reversed Configuration Experiment

    Science.gov (United States)

    Smirnov, Artem

    2016-10-01

    In the C-2 field-reversed configuration (FRC) experiment, tangential neutral beam injection (20 - 40 keV hydrogen, 4 MW total), coupled with electrically-biased plasma guns at the plasma ends, magnetic end plugs, and advanced surface conditioning, led to dramatic reductions in turbulence-driven losses and greatly improved plasma stability. Under such conditions, highly reproducible FRCs with a significant fast-ion population and total plasma temperature of about 1 keV were achieved. The FRC's were macroscopically stable and decayed on characteristic transport time scales of a few milliseconds. In order to sustain an FRC configuration, the C-2 device was upgraded with a new neutral beam injection (NBI) system, which can deliver a total of 10 + MW of hydrogen beam power, by far the largest ever used in a compact toroid plasma experiment. Compared to C-2, the beam energy was lowered to 15 keV and angled injection geometry was adopted to provide better beam coupling to the FRC. The upgraded neutral beams produce a dominant fast ion population that makes a dramatic beneficial impact on the overall plasma performance. Specifically: (1) high-performance, advanced beam-driven FRCs were produced and sustained for times significantly longer (5 + ms) than all characteristic plasma decay times without the beams, (2) the sustainment is fully correlated with neutral beam injection, (3) confinement of fast ions is close to the classical limit, and (4) new, benign collective fast ion effects were observed. Collectively, these accomplishments represent a dramatic advance towards the scientific validation of the FRC-based approach to fusion. This talk will provide a comprehensive overview of the C-2U device and recent experimental advances.

  1. Effects of the measurement configuration in GPR prospecting

    Science.gov (United States)

    Persico, Raffaele; Soldovieri, Francesco

    2017-04-01

    The measurement configuration is an issue of great interest in problems of inverse scattering in general, and in particular in problems regarding GPR data. In particular, the measurement configuration has an influence on the amount of retrievable information [1-2] and can be a way to achieve an intrinsic two dimensional filtering of the data [3], possibly accounting for the characteristics of the exploited antennas too [4]. However, no filter is able to erase exactly the undesired contribution to the comprehensive signal while leaving unperturbed the useful part of the gathered datum. In other word, any filtering of the data (included those implicitly imposed through the measurement configuration) has some price in terms of loss or distortion of the received information, and therefore it has to be applied only when needed and only at the right degree of intensity. In particular, differential measurement configurations have been introduced in the last few years, especially with interest in the field of detection of UXO [5-6]. The filtering effects in some differential configuration are not immediately understood, but need some deep reasoning. In particular, the theory of the diffraction tomography, allows to quantify the retrievable spatial frequencies under the measurement configuration at hand, and so allows to quantify the filtering effect of the differential configurations. Examples will be shown at the conference, regarding both a horizontal and a vertical differential configuration. References [1] R. Persico, R. Bernini, F. Soldovieri, "The role of the measurement configuration in inverse scattering from buried objects under the Born approximation", IEEE Trans. On Antennas and Prop., vol. 53, n. 6, pp. 1875-1886, June 2005. [2] R. Persico, "On the role of measurement Configuration in Contactless GPR data Processing by Means of Linear Inverse Scattering, IEEE Trans. On Antennas and Prop AP, Vol. 54 n. 7 p. 2062-2071, July 2006. [3] R. Persico, F. Soldovieri

  2. Field line mapping and equilibrium reconstructions in new CNT Configuration

    Science.gov (United States)

    Traverso, Peter; Pedersen, Thomas; Brenner, Paul; Sarasola, Xabier; Durand de Gevigney, Benoit

    2010-11-01

    The Columbia Non-neutral Torus (CNT) has the useful feature of having adjustable coil geometry, creating up to three different stellarators each having a completely new shape to its magnetic surfaces and a different Iota profile. Recently the tilt angle between the two interlocking coils has been changed for the first time on CNT, allowing a study of the new magnetic geometry. In the new configuration field line mapping has been accomplished for multiple current ratios and magnetic fields to confirm the existence of good nested magnetic surfaces. At a specific current ratio a large one-three island chain is created. Plasma parameters have been measured with the new coil configuration, both in cases of a large internal island chain, and in cases without. Full 3D equilibrium reconstructions of potential and density are being performed using a modified version of the existing Poisson-Boltzmann solver. Field line mapping in this configuration will be presented, and a progress report on the equilibrium reconstructions will also be given.

  3. Nonequilibrium Dynamics Of Emergent Field Configurations

    CERN Document Server

    Howell, R C

    2003-01-01

    The processes by which nonlinear physical systems approach thermal equilibrium is of great importance in many areas of science. Central to this is the mechanism by which energy is transferred between the many degrees of freedom comprising these systems. With this in mind, in this research the nonequilibrium dynamics of nonperturbative fluctuations within Ginzburg-Landau models are investigated. In particular, two questions are addressed. In both cases the system is initially prepared in one of two minima of a double-well potential. First, within the context of a (2 + 1) dimensional field theory, we investigate whether emergent spatio-temporal coherent structures play a dynamcal role in the equilibration of the field. We find that the answer is sensitive to the initial temperature of the system. At low initial temperatures, the dynamics are well approximated with a time-dependent mean-field theory. For higher temperatures, the strong nonlinear coupling between the modes in the field does give rise to the synch...

  4. Drift-wave stability in the field-reversed configuration

    Science.gov (United States)

    Lau, C. K.; Fulton, D. P.; Holod, I.; Lin, Z.; Binderbauer, M.; Tajima, T.; Schmitz, L.

    2017-08-01

    Gyrokinetic simulations of C-2-like field-reversed configuration (FRC) find that electrostatic drift-waves are locally stable in the core. The stabilization mechanisms include finite Larmor radius effects, magnetic well (negative grad-B), and fast electron short circuit effects. In the scrape-off layer (SOL), collisionless electrostatic drift-waves in the ion-to-electron-scale are destabilized by electron temperature gradients due to the resonance with locally barely trapped electrons. Collisions can suppress this instability, but a collisional drift-wave instability still exists at realistic pressure gradients. Simulation results are in qualitative agreement with C-2 FRC experiments. In particular, the lack of ion-scale instability in the core is not inconsistent with experimental measurements of a fluctuation spectrum showing a depression at ion-scales. The pressure gradient thresholds for the SOL instability from simulations are also consistent with the critical gradient behavior observed in experiments.

  5. Stochastic multi-configurational self-consistent field theory

    CERN Document Server

    Thomas, Robert E; Alavi, Ali; Booth, George H

    2015-01-01

    The multi-configurational self-consistent field theory is considered the standard starting point for almost all multireference approaches required for strongly-correlated molecular problems. The limitation of the approach is generally given by the number of strongly-correlated orbitals in the molecule, as its cost will grow exponentially with this number. We present a new multi-configurational self-consistent field approach, wherein linear determinant coefficients of a multi-configurational wavefunction are optimized via the stochastic full configuration interaction quantum Monte Carlo technique at greatly reduced computational cost, with non-linear orbital rotation parameters updated variationally based on this sampled wavefunction. This extends this approach to strongly-correlated systems with far larger active spaces than it is possible to treat by conventional means. By comparison with this traditional approach, we demonstrate that the introduction of stochastic noise in both the determinant amplitudes an...

  6. Steady state magnetic field configurations for the earth's magnetotail

    Science.gov (United States)

    Hau, L.-N.; Wolf, R. A.; Voigt, G.-H.; Wu, C. C.

    1989-01-01

    A two-dimensional, force-balance magnetic field model is presented. The theoretical existence of a steady state magnetic field configuration that is force-balanced and consistent with slow, lossless, adiabatic, earthward convection within the limit of the ideal MHD is demonstrated. A numerical solution is obtained for a two-dimensional magnetosphere with a rectangular magnetopause and nonflaring tail. The results are consistent with the convection time sequences reported by Erickson (1985).

  7. Non Abelian TQFT and scattering of self dual field configuration

    CERN Document Server

    Gianvittorio, R; Sánchez, J F

    1999-01-01

    A non-abelian topological quantum field theory describing the scattering of self-dual field configurations over topologically non-trivial Riemann surfaces, arising from the reduction of 4-dim self-dual Yang-Mills fields, is introduced. It is shown that the phase space of the theory can be exactly quantized in terms of the space of holomorphic structures over stable vector bundles of degree zero over Riemann surfaces. The Dirac monopoles are particular static solutions of the field equations. Its relation to topological gravity is discussed.

  8. Configuration resonance in scattering scanning near-field optical microscopy

    Institute of Scientific and Technical Information of China (English)

    2007-01-01

    A theoretical model is proposed in order to study the configuration resonance in s-SNOM. The electromagnetic coupling between the sample and the probe tip is described with the quasi-electrostatic field theory. This method permits us to analyze the configurational resonance evoked by the interaction between the probe tip and the sample in s-SNOM intuitively.The resonant conditions for a certain system are presented in an explicit form. On the condition of considering the actual size of the sample dipoles and the probe dipole, we discuss the possibility of realizing the configurational resonance for various material samples. The numerical results indicate that the polarizability of the dielectric probe tip is too small to arouse this resonance, whereas, with the surface plasmon resonance emerging on the metallic nanoparticles, the enhanced polarizability of the metallic probe tip ensures the requirements of fulfilling the resonance.

  9. Transport studies in high-performance field reversed configuration plasmas

    Science.gov (United States)

    Gupta, S.; Barnes, D. C.; Dettrick, S. A.; Trask, E.; Tuszewski, M.; Deng, B. H.; Gota, H.; Gupta, D.; Hubbard, K.; Korepanov, S.; Thompson, M. C.; Zhai, K.; Tajima, T.

    2016-05-01

    A significant improvement of field reversed configuration (FRC) lifetime and plasma confinement times in the C-2 plasma, called High Performance FRC regime, has been observed with neutral beam injection (NBI), improved edge stability, and better wall conditioning [Binderbauer et al., Phys. Plasmas 22, 056110 (2015)]. A Quasi-1D (Q1D) fluid transport code has been developed and employed to carry out transport analysis of such C-2 plasma conditions. The Q1D code is coupled to a Monte-Carlo code to incorporate the effect of fast ions, due to NBI, on the background FRC plasma. Numerically, the Q1D transport behavior with enhanced transport coefficients (but with otherwise classical parametric dependencies) such as 5 times classical resistive diffusion, classical thermal ion conductivity, 20 times classical electron thermal conductivity, and classical fast ion behavior fit with the experimentally measured time evolution of the excluded flux radius, line-integrated density, and electron/ion temperature. The numerical study shows near sustainment of poloidal flux for nearly 1 ms in the presence of NBI.

  10. The Impact of Well-Field Configuration on Plume Persistence

    Science.gov (United States)

    Guo, Z.; Brusseau, M.

    2013-12-01

    It is now recognized that most sites with large groundwater contaminant plumes will require many decades before cleanup will be achieved under current methods and standards. Conceptually, the factors that contribute to plume persistence have long been established, including uncontrolled source zones, dispersed reservoirs of dissolved (present in lower-permeability zones) and sorbed contaminant, and hydraulic-related factors such as non-optimal remedial well-field performance. Of these potential factors, hydraulic phenomena associated with configuration and operation of the well field employed for remedial operations have received minimal attention. The objective of this research is to investigate the influence of well-field configuration on contaminant mass removal and reduction in contaminant mass discharge (CMD). Mathematical modeling, implemented using MODFLOW and MT3D, was conducted to simulate scenarios with different well-field configurations in both homogenous and heterogeneous aquifers. The system was designed such that contaminant was present as only aqueous and sorbed mass (no separate organic-liquid sources). The impacts of several variables on the results are investigated, including pumping rate, layer thickness, and vertical dispersivity. The results are assessed in terms of the relationship between reductions in CMD and reductions in contaminant mass.

  11. Combining configurational energies and forces for molecular force field optimization

    Science.gov (United States)

    Vlcek, Lukas; Sun, Weiwei; Kent, Paul R. C.

    2017-10-01

    While quantum chemical simulations have been increasingly used as an invaluable source of information for atomistic model development, the high computational expenses typically associated with these techniques often limit thorough sampling of the systems of interest. It is therefore of great practical importance to use all available information as efficiently as possible, and in a way that allows for consistent addition of constraints that may be provided by macroscopic experiments. Here we propose a simple approach that combines information from configurational energies and forces generated in a molecular dynamics simulation to increase the effective number of samples. Subsequently, this information is used to optimize a molecular force field by minimizing the statistical distance similarity metric. We illustrate the methodology on an example of a trajectory of configurations generated in equilibrium molecular dynamics simulations of argon and water and compare the results with those based on the force matching method.

  12. Two-Fluid Physics and Field Reversed Configurations

    Science.gov (United States)

    Hakim, Ammar

    2006-10-01

    Fluid models of plasmas are a common tool to study fusion devices. In this talk algorithms for the solution of Two-Fluid plasma equations are presented and applied to the study of Field Reversed Configurations (FRCs). The Two-Fluid model is more general than the often used magnetohydrodynamic (MHD) model. The model takes into account electron inertia, charge separation and the full electromagnetic field equations and allows for separate electron and ion motion. Finite Lamor Radii effects are taken into account by self consistently evolving the anisotropic pressure tensor. The algorithm presented is the high resolution wave propagation scheme. The wave propagation method is based on solutions to the Riemann problem at cell interfaces. Operator splitting is used to incorporate the Lorentz and electromagnetic source terms. To preserve the divergence constraints on the electric and magnetic fields the so called perfectly-hyperbolic form of Maxwell equations are used which explicitly incorporate the divergence equations into the time stepping scheme. A detailed study of Field-Reversed Configuration stability and formation is performed. The study is divided into two parts. In the first, FRC stability is studied. The simulation is initialized with various FRC equilibria and perturbed. The growth rates are calculated and compared with MHD results. It is shown that the FRCs are indeed more stable within the Two-Fluid model than the MHD model. In the second part formation of FRCs is studied. In this set of simulations a cylindrical column of plasma is initialized with a uniform axial magnetic field. The field is reversed at the walls. Via the process of magnetic reconnection FRC formation is observed. The effects of Rotating Magnetic Field (RMF) drive on the formation of FRC are also presented. Here, a set of current carrying coils apply a RMF at the plasma boundary, causing a electron flow in the R-Z plane leading to field reversal. The strong azimuthal electron flow causes

  13. Gyrokinetic particle simulation of a field reversed configuration

    Energy Technology Data Exchange (ETDEWEB)

    Fulton, D. P., E-mail: dfulton@uci.edu; Lau, C. K.; Holod, I.; Lin, Z., E-mail: zhihongl@uci.edu [Department of Physics and Astronomy, University of California, Irvine, California 92697 (United States); Dettrick, S. [Tri Alpha Energy, Inc., Rancho Santa Margarita, California 92688 (United States)

    2016-01-15

    Gyrokinetic particle simulation of the field-reversed configuration (FRC) has been developed using the gyrokinetic toroidal code (GTC). The magnetohydrodynamic equilibrium is mapped from cylindrical coordinates to Boozer coordinates for the FRC core and scrape-off layer (SOL), respectively. A field-aligned mesh is constructed for solving self-consistent electric fields using a semi-spectral solver in a partial torus FRC geometry. This new simulation capability has been successfully verified and driftwave instability in the FRC has been studied using the gyrokinetic simulation for the first time. Initial GTC simulations find that in the FRC core, the ion-scale driftwave is stabilized by the large ion gyroradius. In the SOL, the driftwave is unstable on both ion and electron scales.

  14. Hamiltonian description of closed configurations of the vacuum magnetic field

    Energy Technology Data Exchange (ETDEWEB)

    Skovoroda, A. A., E-mail: skovoroda-aa@nrcki.ru [National Research Centre Kurchatov Institute (Russian Federation)

    2015-05-15

    Methods of obtaining and using the Hamiltonians of closed vacuum magnetic configurations of fusion research systems are reviewed. Various approaches to calculate the flux functions determining the Hamiltonian are discussed. It is shown that the Hamiltonian description allows one not only to reproduce all traditional results, but also to study the behavior of magnetic field lines by using the theory of dynamic systems. The potentialities of the Hamiltonian formalism and its close relation to traditional methods are demonstrated using a large number of classical examples adopted from the fundamental works by A.I. Morozov, L.S. Solov’ev, and V.D. Shafranov.

  15. A Robust Electrode Configuration for Bioimpedance Measurement of Respiration

    Directory of Open Access Journals (Sweden)

    Hong-bin Wang

    2014-01-01

    Full Text Available Electrode configuration is an important issue in the continuous measurement of respiration using impedance pneumography (IP. The robust configuration is usually confirmed by comparing the amplitude of the IP signals acquired with different electrode configurations, while the relative change in waveform and the effects of body posture and respiratory pattern are ignored. In this study, the IP signals and respiratory volume are simultaneously acquired from 8 healthy subjects in supine, left lying, right lying and prone postures, and the subjects are asked to perform four respiratory patterns including free breathing, thoracic breathing, abdominal breathing and apnea. The IP signals are acquired with four different chest electrode configurations, and the volume are measured using pneumotachograph (PNT. Differences in correlation and absolute deviation between the IP-derived and PNT-derived respiratory volume are assessed. The influences of noise, respiratory pattern and body posture on the IP signals of different configurations have significant difference (p < 0.05. The robust electrode configuration is found on the axillary midline, which is suitable for long term respiration monitoring.

  16. A robust electrode configuration for bioimpedance measurement of respiration.

    Science.gov (United States)

    Wang, Hong-Bin; Yen, Chen-Wen; Liang, Jing-Tao; Wang, Qian; Liu, Guan-Zheng; Song, Rong

    2014-01-01

    Electrode configuration is an important issue in the continuous measurement of respiration using impedance pneumography (IP). The robust configuration is usually confirmed by comparing the amplitude of the IP signals acquired with different electrode configurations, while the relative change in waveform and the effects of body posture and respiratory pattern are ignored. In this study, the IP signals and respiratory volume are simultaneously acquired from 8 healthy subjects in supine, left lying, right lying and prone postures, and the subjects are asked to perform four respiratory patterns including free breathing, thoracic breathing, abdominal breathing and apnea. The IP signals are acquired with four different chest electrode configurations, and the volume are measured using pneumotachograph (PNT). Differences in correlation and absolute deviation between the IP-derived and PNT-derived respiratory volume are assessed. The influences of noise, respiratory pattern and body posture on the IP signals of different configurations have significant difference (p < 0.05). The robust electrode configuration is found on the axillary midline, which is suitable for long term respiration monitoring.

  17. Measuring Effects on the Clinical Practice from a Configured EHR

    DEFF Research Database (Denmark)

    Møller-Jensen, John; Simonsen, Jesper; K. Iversen, Rikke

    2006-01-01

    during a series of workshops with the clinicians after which the XML configuration files were written and deployed. In parallel with this, the participants from the University specified a number of effects related to the clinical practice to be measured. Measurements were focused on the requested effects...

  18. Optimizing the configuration patterns for heterogeneous distributed sensor fields

    Science.gov (United States)

    Wettergren, Thomas A.; Costa, Russell

    2012-06-01

    When unmanned distributed sensor fields are developed for rapid deployment in hostile areas, the deployment may consist of multiple sensor types. This occurs because of the variations in expected threats and uncertainties about the details of the local environmental conditions. As more detailed information is available at deployment, the quantity and types of sensors are given and fixed, yet the specific pattern for the configuration of their deployment is still variable. We develop a new optimization approach for planning these configurations for this resource constrained sensor application. Our approach takes into account the variety of sensors available and their respective expected performance in the environment, as well as the target uncertainty. Due to the large dimensionality of the design space for this unmanned sensor planning problem, heuristic-based optimizations will provide very sub-optimal solutions and gradient-based methods lack a good quality initialization. Instead, we utilize a robust optimization procedure that combines genetic algorithms with nonlinear programming techniques to create numerical solutions for determining the optimal spatial distribution of sensing effort for each type of sensor. We illustrate the effectiveness of the approach on numerical examples, and also illustrate the qualitative difference in the optimal patterns as a function of the relative numbers of available sensors of each type. We conclude by using the optimization results to discuss the benefits of interspersing the different sensor types, as opposed to creating area sub-segmentations for each type.

  19. The Einstein field equations for cylindrically symmetric elastic configurations

    Energy Technology Data Exchange (ETDEWEB)

    Brito, I; Vaz, E G L R [Departamento de Matematica e Aplicacoes, Universidade do Minho, 4800-058 Guimaraes (Portugal); Carot, J, E-mail: ireneb@math.uminho.pt, E-mail: jcarot@uib.cat, E-mail: evaz@math.uminho.pt [Departament de Fisica, Universitat de les Illes Balears, Cra Valdemossa pk 7.5, E-07122 Palma (Spain)

    2011-09-22

    In the context of relativistic elasticity it is interesting to study axially symmetric space-times due to their significance in modeling neutron stars and other astrophysical systems of interest. To approach this problem, here, a particular class of these space-times is considered. A cylindrically symmetric elastic space-time configuration is studied, where the material metric is taken to be flat. The components of the energy-momentum tensor for elastic matter are written in terms of the invariants of the strain tensor, here chosen to be the eigenvalues of the pulled-back material metric. The Einstein field equations are presented and a condition confirming the existence of a constitutive function is obtained. This condition leads to special cases, in one of which a new system for the metric functions and an expression for the constitutive function are deduced. The new system depends on a particular function, which builds up the constitutive equation.

  20. Profile stabilization of tilt mode in a Field Reversed Configuration

    Energy Technology Data Exchange (ETDEWEB)

    Cobb, J.W.; Tajima, T. [Texas Univ., Austin, TX (United States). Inst. for Fusion Studies; Barnes, D.C. [Los Alamos National Lab., NM (United States)

    1993-06-01

    The possibility of stabilizing the tilt mode in Field Reversed Configurations without resorting to explicit kinetic effects such as large ion orbits is investigated. Various pressure profiles, P({Psi}), are chosen, including ``hollow`` profiles where current is strongly peaked near the separatrix. Numerical equilibria are used as input for an initial value simulation which uses an extended Magnetohydrodynamic (MHD) model that includes viscous and Hall terms. Tilt stability is found for specific hollow profiles when accompanied by high values of separatrix beta, {beta}{sub sep}. The stable profiles also have moderate to large elongation, racetrack separatrix shape, and lower values of 3, average ratio of Larmor radius to device radius. The stability is unaffected by changes in viscosity, but the neglect of the Hall term does cause stable results to become marginal or unstable. Implications for interpretation of recent experiments are discussed.

  1. Gyrokinetic simulation of driftwave instability in field-reversed configuration

    Science.gov (United States)

    Fulton, D. P.; Lau, C. K.; Schmitz, L.; Holod, I.; Lin, Z.; Tajima, T.; Binderbauer, M. W.

    2016-05-01

    Following the recent remarkable progress in magnetohydrodynamic (MHD) stability control in the C-2U advanced beam driven field-reversed configuration (FRC), turbulent transport has become one of the foremost obstacles on the path towards an FRC-based fusion reactor. Significant effort has been made to expand kinetic simulation capabilities in FRC magnetic geometry. The recently upgraded Gyrokinetic Toroidal Code (GTC) now accommodates realistic magnetic geometry from the C-2U experiment at Tri Alpha Energy, Inc. and is optimized to efficiently handle the FRC's magnetic field line orientation. Initial electrostatic GTC simulations find that ion-scale instabilities are linearly stable in the FRC core for realistic pressure gradient drives. Estimated instability thresholds from linear GTC simulations are qualitatively consistent with critical gradients determined from experimental Doppler backscattering fluctuation data, which also find ion scale modes to be depressed in the FRC core. Beyond GTC, A New Code (ANC) has been developed to accurately resolve the magnetic field separatrix and address the interaction between the core and scrape-off layer regions, which ultimately determines global plasma confinement in the FRC. The current status of ANC and future development targets are discussed.

  2. Interpretation of the coronal magnetic field configuration of the Sun

    Institute of Scientific and Technical Information of China (English)

    Bo Li; Xing Li; Hui Yu

    2012-01-01

    The origin of the heliospheric magnetic flux on the Sun,and hence the origin of the solar wind,is a topic of hot debate.While the prevailing view is that the solar wind originates from outside the coronal streamer helmets,there also exists the suggestion that the open magnetic field spans a far wider region.Without the definitive measurement of the coronal magnetic field,it is difficult to unambiguously resolve the conflict between the two scenarios.We present two 2-dimensional,Alfvénic-turbulence-based models of the solar corona and solar wind,one with and the other without a closed magnetic field region in the inner corona.The purpose of the latter model is to test whether it is possible to realize a picture suggested by polarimetric measurements of the corona using the Fe ⅩⅢ 10747(A) line,where open magnetic field lines seem to penetrate the streamer base.The boundary conditions at the coronal base are able to account for important observational constraints,especially those on the magnetic flux distribution.Interestingly,the two models provide similar polarized brightness (pB) distributions in the field of view (FOV) of SOHO/LASCO C2 and C3 coronagraphs.In particular,a dome-shaped feature is present in the C2 FOV even for the model without a closed magnetic field.Moreover,both models fit the Ulysses data scaled to 1 AU equally well.We suggest that:1) The pB observations cannot be safely taken as a proxy for the magnetic field topology,as is often implicitly assumed.2) The Ulysses measurements,especially the one showing a nearly uniform distribution with heliocentric latitude of the radial magnetic field,do not rule out the ubiquity of open magnetic fields on the Sun.

  3. Inhomogeneous field configurations and the electroweak phase transition

    CERN Document Server

    Jungnickel, D U; Jungnickel, Dirk-Uwe; Walliser, Dirk

    1994-01-01

    We investigate the effects of inhomogeneous scalar field configurations on the electroweak phase transition. For this purpose we calculate the leading perturbative correction to the wave function correction term $Z(\\vph,T)$, i.e., the kinetic term in the effective action, for the electroweak Standard Model at finite temperature and the top quark self--mass. Our finding for the fermionic contribution to $Z(\\vph,T)$ is infra--red finite and disagrees with other recent results. In general, neither the order of the phase transition nor the temperature at which it occurs change, once $Z(\\vph,T)$ is included. But a non--vanishing, positive (negative) $Z(\\vph,T)$ enhances (decreases) the critical droplet surface tension and the strength of the phase transition. We find that in the range of parameter space, which allows for a first--order phase transition, the wave function correction term is negative --- indicating a weaker phase transition --- and especially for small field values so large that perturbation theory ...

  4. Exploring the magnetic field configuration in BL Lac using GMVA

    CERN Document Server

    Rani, B; Hodgson, J; Koyama, S; Zensus, J A; Fuhrmann, L; Marscher, A P; Jorstad, S G

    2016-01-01

    The high radio frequency polarization imaging of non-thermal emission from active galactic nuclei (AGN) is a direct way to probe the magnetic field strength and structure in the immediate vicinity of supermassive black holes (SMBHs) and is crucial in testing the jet-launching scenario. To explore the the magnetic field configuration at the base of jets in blazars, we took advantage of the full polarization capabilities of the Global Millimeter VLBI Array (GMVA). With an angular resolution of $\\sim$50 micro-arcseconds ($\\mu$as) at 86 GHz, one could resolve scales up to $\\sim$450 gravitational radii (for a 10$^9$ solar mass black hole at a redshift of 0.1). We present here the preliminary results of our study on the blazar BL~Lac. Our results suggest that on sub-mas scales the core and the central jet of BL Lac are significantly polarized with two distinct regions of polarized intensity. We also noted a great morphological similarity between the 7mm/3mm VLBI images at very similar angular resolution.

  5. Thick Liquid-Walled, Field-Reversed Configuration

    Energy Technology Data Exchange (ETDEWEB)

    Moir, R W; Bulmer, R H; Gulec, K; Fogarty, P; Nelson, B; Ohnishi, M; Rensink, M; Rognlien, T D; Santarious, J F; Sze, D K

    2000-09-22

    A thick flowing layer of liquid (e.g., flibe--a molten salt, or Sn{sub 80}Li{sub 20}--a liquid metal) protects the structural walls of the field-reversed configuration (FRC) so that they can last the life of the plant even with intense 14 MeV neutron bombardment from the D-T fusion reaction. The surface temperature of the liquid rises as it passes from the inlet nozzles to the exit or receiver nozzles due to absorption of line and bremsstrahlung radiation, and neutrons. The surface temperature can be reduced by enhancement of convection near the surface to transport hot surface liquid into the cooler interior. This surface temperature must be compatible with a practical heat transport and energy recovery system. The evaporative flux from the wall driven by the surface temperature must also result in an acceptable impurity level in the core plasma. The shielding of the core by the edge plasma is modeled with a 2D transport code for the resulting impurity ions; these ions are either swept out to the distant end tanks, or diffuse to the hot plasma core. An auxiliary plasma between the edge plasma and the liquid wall can further attenuate evaporating flux of atoms and molecules by ionization. The current in this auxiliary plasma might serve as the antenna for the current drive method, which produces a rotating magnetic field. Another method of current drive uses small spheromaks injected along the magnetic fields, which additionally provide fueling along with pellet fueling if necessary.

  6. Ultrasound Tomography in Circular Measurement Configuration using Nonlinear Reconstruction Method

    Directory of Open Access Journals (Sweden)

    Tran Quang-Huy

    2015-12-01

    Full Text Available Ultrasound tomography offers the potential for detecting of very small tumors whose sizes are smaller than the wavelength of the incident pressure wave without ionizing radiation. Based on inverse scattering technique, this imaging modality uses some material properties such as sound contrast and attenuation in order to detect small objects. One of the most commonly used methods in ultrasound tomography is the Distorted Born Iterative Method (DBIM. The compressed sensing technique was applied in the DBIM as a promising approach for the image reconstruction quality improvement. Nevertheless, the random measurement configuration of transducers in this method is very difficult to set up in practice. Therefore, in this paper, we take advantages of simpler sparse uniform measurement configuration set-up of transducers and high-quality image reconstruction of 1 non-linear regularization in sparse scattering domain. The simulation results demonstrate the high performance of the proposed approach in terms of tremendously reduced total runtime and normalized error.

  7. Comparing different stimulus configurations for population receptive field mapping in human fMRI

    Directory of Open Access Journals (Sweden)

    Ivan eAlvarez

    2015-02-01

    Full Text Available Population receptive field (pRF mapping is a widely used approach to measuring aggregate human visual receptive field properties by recording non-invasive signals using functional MRI. Despite growing interest, no study to date has systematically investigated the effects of different stimulus configurations on pRF estimates from human visual cortex. Here we compared the effects of three different stimulus configurations on a model-based approach to pRF estimation: size-invariant bars and eccentricity-scaled bars defined in Cartesian coordinates and traveling along the cardinal axes, and a novel simultaneous ‘wedge and ring’ stimulus defined in polar coordinates, systematically covering polar and eccentricity axes. We found that the presence or absence of eccentricity scaling had a significant effect on goodness of fit and pRF size estimates. Further, variability in pRF size estimates was directly influenced by stimulus configuration, particularly for higher visual areas including V5/MT+. Finally, we compared eccentricity estimation between phase-encoded and model-based pRF approaches. We observed a tendency for more peripheral eccentricity estimates using phase-encoded methods, independent of stimulus size. We conclude that both eccentricity scaling and polar rather than Cartesian stimulus configuration are important considerations for optimal experimental design in pRF mapping. While all stimulus configurations produce adequate estimates, simultaneous wedge and ring stimulation produced higher fit reliability, with a significant advantage in reduced acquisition time.

  8. Resonance and Chaotic Trajectories in Magnetic Field Reversed Configuration

    Energy Technology Data Exchange (ETDEWEB)

    A.S. Landsman; S.A. Cohen; M. Edelman; G.M. Zaslavsky

    2005-04-13

    The nonlinear dynamics of a single ion in a field-reversed configuration (FRC) were investigated. FRC is a toroidal fusion device which uses a specific type of magnetic field to confine ions. As a result of angular invariance, the full three-dimensional Hamiltonian system can be expressed as two coupled, highly nonlinear oscillators. Due to the high nonlinearity in the equations of motion, the behavior of the system is extremely complex, showing different regimes, depending on the values of the conserved canonical angular momentum and the geometry of the fusion vessel. Perturbation theory and averaging were used to derive the unperturbed Hamiltonian and frequencies of the two degrees of freedom. The derived equations were then used to find resonances and compare to Poincar{copyright} surface-of-section plots. A regime was found where the nonlinear resonances were clearly separated by KAM [Kolmogorov-Arnold-Mosher] curves. The structure of the observed island chains was explained. The condition for the destruction of KAM curves and the onset of strong chaos was derived, using Chirikov island overlap criterion, and shown qualitatively to depend both on the canonical angular momentum and geometry of the device. After a brief discussion of the adiabatic regime the paper goes on to explore the degenerate regime that sets in at higher values of angular momenta. In this regime, the unperturbed Hamiltonian can be approximated as two uncoupled linear oscillators. In this case, the system is near-integrable, except in cases of a universal resonance, which results in large island structures, due to the smallness of nonlinear terms, which bound the resonance. The linear force constants, dominant in this regime, were derived and the geometry for a large one-to-one resonance identified. The above analysis showed good agreement with numerical simulations and was able to explain characteristic features of the dynamics.

  9. Studies on different configurations of cobalt phthalocyanine based flexible organic field effect transistor

    Science.gov (United States)

    Kumar, A.; Jha, P.; Samanta, S.; Singh, A.; Debnath, A. K.; Aswal, D. K.; Gupta, S. K.

    2016-05-01

    Organic Field Effect Transistors (OFETs) are being investigated for a number of low-cost, large area applications; particularly those that are compatible with flexible plastic substrates. Development of low temperature processes can make way for OFETs to be integrated on flexible plastic substrates. Here we have made systematic studies on OFETs in different configurations wherein we have chosen Cobalt Phthalocyanine (CoPc) as active material. We have found the best mobility (1.86 × 10-5 cm2/V-s) in Bottom Gate Top Contact configuration. However, threshold voltage (-5V) and On off ratio (62)were found to be better in Top Gate Bottom Contact configuration The electromechanical properties of the Bottom Gate Top Contact transistors were studied by measuring the transfer characteristics of the devices in bend condition and thereby calculating mobility under different radii of bending. No significant change in the mobility of the device was observed under bent conditions.

  10. Measure Guideline: Optimizing the Configuration of Flexible Duct Junction Boxes

    Energy Technology Data Exchange (ETDEWEB)

    Beach, R.; Burdick, A.

    2014-03-01

    This measure guideline offers additional recommendations to heating, ventilation, and air conditioning (HVAC) system designers for optimizing flexible duct, constant-volume HVAC systems using junction boxes within Air Conditioning Contractors of America (ACCA) Manual D guidance (Rutkowski, H. Manual D -- Residential Duct Systems, 3rd edition, Version 1.00. Arlington, VA: Air Conditioning Contractors of America, 2009.). IBACOS used computational fluid dynamics software to explore and develop guidance to better control the airflow effects of factors that may impact pressure losses within junction boxes among various design configurations (Beach, R., Prahl, D., and Lange, R. CFD Analysis of Flexible Duct Junction Box Design. Golden, CO: National Renewable Energy Laboratory, submitted for publication 2013). These recommendations can help to ensure that a system aligns more closely with the design and the occupants' comfort expectations. Specifically, the recommendations described herein show how to configure a rectangular box with four outlets, a triangular box with three outlets, metal wyes with two outlets, and multiple configurations for more than four outlets. Designers of HVAC systems, contractors who are fabricating junction boxes on site, and anyone using the ACCA Manual D process for sizing duct runs will find this measure guideline invaluable for more accurately minimizing pressure losses when using junction boxes with flexible ducts.

  11. Measure Guideline: Optimizing the Configuration of Flexible Duct Junction Boxes

    Energy Technology Data Exchange (ETDEWEB)

    Beach, R. [IBACOS, Inc., Pittsburgh, PA (United States); Burdick, A. [IBACOS, Inc., Pittsburgh, PA (United States)

    2014-03-01

    This measure guideline offers additional recommendations to heating, ventilation, and air conditioning (HVAC) system designers for optimizing flexible duct, constant-volume HVAC systems using junction boxes within Air Conditioning Contractors of America (ACCA) Manual D guidance. IBACOS used computational fluid dynamics software to explore and develop guidance to better control the airflow effects of factors that may impact pressure losses within junction boxes among various design configurations. These recommendations can help to ensure that a system aligns more closely with the design and the occupants' comfort expectations. Specifically, the recommendations described herein show how to configure a rectangular box with four outlets, a triangular box with three outlets, metal wyes with two outlets, and multiple configurations for more than four outlets. Designers of HVAC systems, contractors who are fabricating junction boxes on site, and anyone using the ACCA Manual D process for sizing duct runs will find this measure guideline invaluable for more accurately minimizing pressure losses when using junction boxes with flexible ducts.

  12. Measurement of the Clinical Usability of a Configurable EHR

    DEFF Research Database (Denmark)

    Møller-Jensen, John; Lund Pedersen, Ivan; Simonsen, Jesper

    2006-01-01

    requested by the clinicians focused on improving their overview and assessment of patients as well as on more efficient coordination in three specific and highly cooperative situations, viz. nursing handover, ward round and patient conference. All three situations were measured before (using paper......-based medical records) as well as during the week where the configured EHR completely replaced the paper-based medical record in order to compare a ’before’ and ’after’ situation. Measurements were focused on the requested effects and acquired using various techniques including questionnaires, interviews...

  13. Interpretation of the coronal magnetic field configuration of the Sun

    CERN Document Server

    Li, Bo; Yu, Hui

    2012-01-01

    The origin of the heliospheric magnetic flux on the Sun, and hence the origin of the solar wind, is a topic of hot debate.While the prevailing view is that the solar wind originates from outside coronal streamer helmets, there also exists the suggestion that the open magnetic field spans a far wider region.Without the definitive measurement of the coronal magnetic field, it is difficult to resolve the conflict between the two scenarios without doubt.We present two 2-dimensional, Alfv\\'enic-turbulence-based models of the solar corona and solar wind, one with and the other without a closed magnetic field region in the inner corona.The purpose of the latter model is to test whether it is possible to realize a picture suggested by polarimetric measurements of the corona using the FeXIII 10747\\AA\\ line, where open magnetic field lines seem to penetrate the streamer base.The boundary conditions at the coronal base are able to account for important observational constraints, especially those on the magnetic flux dis...

  14. Magnetic Field Configuration at the Galactic Center Investigated by Wide Field Near-Infrared Polarimetry

    CERN Document Server

    Nishiyama, Shogo; Hatano, Hirofumi; Kanai, Saori; Kurita, Mikio; Sato, Shuji; Matsunaga, Noriyuki; Nagata, Tetsuya; Nagayama, Takahiro; Kandori, Ryo; Nakajima, Yasushi; Kusakabe, Nobuhiko; Sato, Yaeko; Hough, James H; Sugitani, Koji; Okuda, Haruyuki

    2008-01-01

    We present a polarimetric map of a 20'x20' area toward the Galactic center. The polarization of point sources has been measured in the J, H, and Ks bands using the near-infrared polarimetric camera SIRPOL on the 1.4 m telescope IRSF. One percent or better accuracy of polarization degree is achieved for sources with J<14.5, H<13.5, and Ks<12.0. Comparing the Stokes parameters between high extinction stars and relatively low extinction ones, we have obtained a polarization originating from magnetically aligned dust grains at the central region of our Galaxy of at most 1-2 kpc. The distribution of the position angles shows a peak at about 20 deg, nearly parallel to the Galactic plane, suggesting a toroidal magnetic configuration. The derived direction of the magnetic field is in good agreement with that obtained from far-infrared/submillimeter observations, which detect polarized thermal emission from dust in the molecular clouds at the Galactic center. Our results show that by subtracting foreground co...

  15. On the Topology of Configurations of Gauge Fields and Higgs Fields

    Science.gov (United States)

    Chaves, R.

    Starting with the topological classification of gauge fields on the sphere (Dirac monopoles) and of Higgs vacuum configurations (through the second homotopy group of the space of vacuum states), the features of minimum energy solutions to gauge theories with spontaneous symmetry breaking and in the presence of singularities (monopoles) are deduced. For each theory, this analysis reveals whether a monopole can exist isolated or must be attached to a massive string and how its flux must be distributed.

  16. Scaling of velocity and mixture fraction fields in laminar counterflow configurations

    Science.gov (United States)

    Bisetti, Fabrizio; Scribano, Gianfranco

    2015-11-01

    Counterflow configurations are widely used to characterize premixed, nonpremixed, and partially premixed laminar flames. We performed a systematic analysis of the velocity and mixture fraction fields in the counterflow configuration and obtained scaling laws, which depend on two suitable nondimensional numbers: (i) the Reynolds number based on the bulk velocity U and half the separation distance between the nozzles L, and (ii) the ratio of the separation distance H = 2 L to the nozzle diameter D. Our study combines velocity measurements via Particle Image Velocimetry, detailed two-dimensional simulations including the nozzle geometry, and an exhaustive analysis of the data based on the nondimensional numbers. The flow field is shown to be moderately sensitive to the Reynolds number and strongly affected by the ratio H / D . By describing the self-similar behavior of the flow field in counterflow configurations comprehensively, our results provide a systematic explanation of existing burner designs as well as clear guidelines for the design of counterflows for pressurized nonpremixed flames. Finally, questions related to the limitations of one-dimensional models for counterflows are addressed conclusively.

  17. Field-reversed configuration maintained by rotating magnetic field with high spatial harmonics.

    Science.gov (United States)

    Inomoto, Michiaki; Kitano, Katsuhisa; Okada, Shigefumi

    2007-10-26

    Field-reversed configurations (FRCs) driven by rotating magnetic fields (RMFs) with spatial high harmonics have been studied in the metal flux conserver of the FRC injection experiment. The experimental results show that the fundamental RMF component is observed to penetrate the plasma column, while the high harmonics are screened at the plasma edge due to their slower or reversed rotation. This selective penetration of the RMF provides good compatibility of radial and azimuthal force balances; significant radial inward force mostly from the high-harmonic components, and sufficient azimuthal torque solely provided by the fundamental component.

  18. High Fidelity Modeling of Field Reversed Configuration (FRC) Thrusters

    Science.gov (United States)

    2015-10-01

    effects as plasma impact neutral background – Fairly straightforward to model with existing fluid tools (high enough collisionality for Maxwellian ...model – Plasmas can have very complex phase space configurations and self-induced electromagnetic forces. Fundamental multiscale problem since...Approved for public release; distribution unlimited Kinetic ( non - Maxwellian ) Can implement Boltzmann equation multiple ways: • PIC (high

  19. Manipulability measure of dual-arm space robot and its application to design an optimal configuration

    Science.gov (United States)

    Zhang, Bo; Liang, Bin; Wang, Xueqian; Li, Gang; Chen, Zhang; Zhu, Xiaojun

    2016-11-01

    Coupling effect exists among different arms and the base in a multi-arm space robot. The manipulability measure of one arm can be affected by the base and the other arms, which has important effects on the configuration optimization, the singularity avoidance and the compliant control. The manipulability measure for a multi-arm space robot is more complex than that of a single-arm space robot. At present, the manipulability measure of a multi-arm space robot has not been studied. In the paper, a new concept of manipulability measure is applied to analyze the manipulability measure for a dual-arm space robot, especially for the manipulability measure of the mission arm subjecting to the influence from coupling effect of auxiliary arm and the base. Based on the manipulability measure of mission arm, a performance index is introduced and used to design and choose an optimization configuration for a dual-arm space robot. Finally, a plane dual-arm space robot is simulated, which is illustrated the influence of joint angles and the base attitude on mission arm's manipulability measure. Simulation results show that the proposed manipulability measure is useful for a multi-arm space robot and optimal configuration can be extended and applied to the coordinated soft rendezvous and docking and the target capture in the field of on-orbit servicing.

  20. A Field-Reversed Configuration Plasma Translated into a Neutral Gas Atmosphere

    Science.gov (United States)

    Sekiguchi, Jun'ichi; Asai, Tomohiko; Takahashi, Tsutomu; Ando, Hirotoshi; Arai, Mamiko; Katayama, Seri; Takahashi, Toshiki

    2014-10-01

    A field-reversed configuration (FRC) is a compact toroid dominantly with poloidal magnetic field. Because of its simply-connected configuration, an FRC can be translated axially along a gradient of guide magnetic field, and trapped in a confinement region with quasi-static external magnetic field. FRC translation experiments have been performed several facilities. Translation speed of those translated FRCs is comparable with super-Alfvenic speed of approximately 200 km/s. In this experiments, FRC translation has been performed on the FAT (FRC Amplification via Translation) facility. Achieved translation speed in the case of translation into a confinement chamber maintained as the vacuum state is in the range from 130 to 210 km/s. On the other hand, FRC translation into a statically filled deuterium gas atmosphere has also been performed. In the case of translation into filled neutral gas, FRC translation speed is approximately 80 km/s and the separatrix volume has extremely expanded compared with the case of a vacuum state. The phenomenon suggests the presence of regeneration process of translation kinetic energy back into the internal plasma energy during the translation process. This work was partially supported by ``Nihon University Symbolic Project.'' The authors gratefully acknowledge contributions from Nac Image Technology Inc. on the fast camera measurements.

  1. Measurement of carbonaceous aerosol with different sampling configurations and frequencies

    Directory of Open Access Journals (Sweden)

    Y. Cheng

    2015-03-01

    Full Text Available Carbonaceous aerosol in Beijing, China was measured with different sampling configurations (denuded vs. un-denuded and frequencies (24 vs. 48 h averaged. Our results suggest that the negative sampling artifact of a bare quartz filter could be remarkably enhanced due to the uptake of water vapor by the filter medium, indicating that the positive sampling artifact tends to be underestimated under high humidity conditions. It was also observed that the analytical artifact (i.e., the underestimation of elemental carbon by the operationally defined value of the thermal-optical method was more apparent for the low frequency samples such that their elemental carbon (EC concentrations were about 15% lower than the reference values measured by the high-frequency, denuded filters. Moreover, EC results of the low frequency samples were found to exhibit a stronger dependence on the charring correction method. In addition, optical attenuation (ATN of EC was retrieved from the carbon analyzer, and the low frequency samples were shown to be more significantly biased by the shadowing effect.

  2. Effects of landscape composition and configuration on pollination in a native herb: a field experiment.

    Science.gov (United States)

    Ekroos, Johan; Jakobsson, Anna; Wideen, Joel; Herbertsson, Lina; Rundlöf, Maj; Smith, Henrik G

    2015-10-01

    Bumble bee abundance in agricultural landscapes is known to decrease with increasing distance from seminatural grasslands, but whether the pollination of bumble-bee-pollinated wild plants shows a similar pattern is less well known. In addition, the relative effects of landscape composition (landscape heterogeneity) and landscape configuration (distance from seminatural grassland) on wild plant pollination, and the interaction between these landscape effects, have not been studied using landscape-level replication. We performed a field experiment to disentangle these landscape effects on the pollination of a native herb, the sticky catchfly (Lychnis viscaria), while accounting for the proportion of oilseed rape across landscapes and the local abundance of bee forage flowers. We measured pollen limitation (the degree to which seed set is pollen-limited), seed set, and seed set stability using potted plants placed in landscapes that differed in heterogeneity (composition) and distance from seminatural grassland (configuration). Pollen limitation and seed set in individual plants did not respond to landscape composition, landscape configuration, or proportion of oilseed rape. Instead, seed set increased with increasing local bee forage flower cover. However, we found within-plant variability in pollen limitation and seed set to increase with increasing distance from seminatural pasture. Our results suggest that average within-plant levels of pollen limitation and seed set respond less swiftly than the within-plant variability in pollen limitation and seed set to changes in landscape configuration. Although landscape effects on pollination were less important than predicted, we conclude that landscape configuration and local habitat characteristics play larger roles than landscape composition in the pollination of L. viscaria.

  3. Measuring Multi-Configurational Character by Orbital Entanglement

    CERN Document Server

    Stein, Christopher J

    2016-01-01

    One of the most critical tasks at the very beginning of a quantum chemical investigation is the choice of either a multi- or single-configurational method. Naturally, many proposals exist to define a suitable diagnostic of the multi-configurational character for various types of wave functions in order to assist this crucial decision. Here, we present a new orbital-entanglement based multi-configurational diagnostic termed $Z_{s(1)}$. The correspondence of orbital entanglement and static (or nondynamic) electron correlation permits the definition of such a diagnostic. We chose our diagnostic to meet important requirements such as well-defined limits for pure single-configurational and multi-configurational wave functions. The $Z_{s(1)}$ diagnostic can be evaluated from a partially converged, but qualitatively correct, and therefore inexpensive density matrix renormalization group wave function as in our recently presented automated active orbital selection protocol. Its robustness and the fact that it can be ...

  4. Passive Superconducting Flux Conservers for Rotating-Magnetic-Field-Driven Field-Reversed Configurations

    Energy Technology Data Exchange (ETDEWEB)

    Oz, E.; Myers, C. E.; Edwards, M. R.; Berlinger, B.; Brooks, A.; Cohen, S. A.

    2011-01-05

    The Princeton Field-Reversed Configuration (PFRC) experiment employs an odd-parity rotating magnetic field (RMFo) current drive and plasma heating system to form and sustain high-Β plasmas. For radial confinement, an array of coaxial, internal, passive, flux-conserving (FC) rings applies magnetic pressure to the plasma while still allowing radio-frequency RMFo from external coils to reach the plasma. The 3 ms pulse duration of the present experiment is limited by the skin time (τfc) of its room-temperature copper FC rings. To explore plasma phenomena with longer characteristic times, the pulse duration of the next-generation PFRC-2 device will exceed 100 ms, necessitating FC rings with (τfc > 300 ms. In this paper we review the physics of internal, discrete, passive FCs and describe the evolution of the PFRC's FC array. We then detail new experiments that have produced higher performance FC rings that contain embedded high-temperature superconducting (HTS) tapes. Several HTS tape winding configurations have been studied and a wide range of extended skin times, from 0.4 s to over 103 s, has been achieved. The new FC rings must carry up to 3 kA of current to balance the expected PFRC-2 plasma pressure, so the dependence of the HTS-FC critical current on the winding configuration and temperature was also studied. From these experiments, the key HTS-FC design considerations have been identified and HTS-FC rings with the desired performance characteristics have been produced.

  5. On the number of soft quanta in classical field configurations

    CERN Document Server

    Mueck, Wolfgang

    2013-01-01

    A central point in the large-N portrait of black holes proposed by Dvali and Gomez is the estimate of the number of soft quanta that make up the classical gravitational field. It is shown here that the coherent state formalism provides a way to calculate that number directly. As a consequence, the average energy of the quanta is such that the typical geometric size of the field source can be roughly interpreted as their de Broglie wavelength. The calculation is done for the electromagnetic field and for Newtonian gravity, and it is argued that the number of soft quanta should be unchanged in General Relativity due to the long range nature of gravity.

  6. Vortex configuration in the presence of local magnetic field and locally applied stress

    Science.gov (United States)

    Wissberg, Shai; Kremen, Anna; Shperber, Yishai; Kalisky, Beena

    2017-02-01

    Vortex configuration is determined by the repulsive interaction, which becomes dominant with increasing vortex density, by the pinning potential, and by other considerations such as the local magnetic fields, currents flowing in the sample, or as we showed recently, by local stress applied on the sample. In this work we describe different ways to control vortex configuration using scanning SQUID microscopy.

  7. Airflow and heat transfer measurements near a facade with different heating configurations

    Energy Technology Data Exchange (ETDEWEB)

    Karava, P.; Tzempelikos, A.; Bessoudo, M.; Candanedo, L.; Athienitis, A. [Concordia Univ., Montreal, PQ (Canada). Dept. of Building, Civil and Environmental Engineering; Handfield, L. [Hydro-Quebec, Shawinigan, PQ (Canada). Research Inst.

    2007-07-01

    The experimental results of temperature and air velocity field measurements near a glazed facade at a research laboratory in Quebec were presented. The experiment examined the air movement and heat transfer near the windows both with and without shading, and with different perimeter heating configurations. The aim of the study was to develop design recommendations for high performance facades to reduce or eliminate perimeter heating in buildings. The chamber was equipped with 3 types of heating systems: (1) a baseboard heater; (2) electrically heated windows; and (3) a radiant ceiling panel. A particle image velocimetry (PIV) system was used to perform velocity field measurements on a vertical plane perpendicular to the window surface. A motorized traverse system was used to conduct measurements at various heights and distances from the facade. Thermal stratification was monitored using a grid of thermocouples. Results showed that maximum temperature variations in the space were observed for the case of baseboard heater and windows covered by roller shades. Without shading, the baseboard heater still had a significant impact on horizontal temperature variation. A comparison between a radiant ceiling panel and the heated window showed that heated windows resulted in more uniform temperature field without vertical stratification, while the ceiling panel heated the air around it at 1.5 degrees C higher than the lower levels. It was noted that further research is now being conducted to predict the air velocity and temperature fields near glazed facades with various perimeter heating configurations and shading attachments. 7 refs., 2 tabs., 16 figs.

  8. Formation of Field-reversed-Configuration Plasma with Punctuated-betatron-orbit Electrons

    Energy Technology Data Exchange (ETDEWEB)

    Welch, D. R.; Cohen, S. A.; Genoni, T. C.; Glasser, A. H.

    2010-06-28

    We describe ab initio, self-consistent, 3D, fully electromagnetic numerical simulations of current drive and field-reversed-configuration plasma formation by odd-parity rotating magnetic fields (RMFo). Magnetic-separatrix formation and field reversal are attained from an initial mirror configuration. A population of punctuated-betatron-orbit electrons, generated by the RMFo, carries the majority of the field-normal azimuthal electrical current responsible for field reversal. Appreciable current and plasma pressure exist outside the magnetic separatrix whose shape is modulated by the RMFo phase. The predicted plasma density and electron energy distribution compare favorably with RMFo experiments. __________________________________________________

  9. Electrical modeling of the Reversed Field Pinch configuration

    Science.gov (United States)

    Cavazzana, Roberto

    2016-10-01

    Starting from the Poynting theorem, a two port equivalent formulation for the Reversed Field Pinch (RFP) is obtained. At first a general formulation applicable to any sort of underlying MHD physics is derived. Then its specialization is discussed, showing that: i) the toroidal field reversal is guided from outside the plasma by the external imposed boundary conditions; ii) the classic textbook RFP derivation with the toroidal flux Φt conserved is only a particular choice among the many possible. Here a parametric force free MHD family of equilibria is used to derive the two port equation of a realistic RFP boundary condition. The key master parameter turns out to be the edge safety factor q (a) = a / R .Bt (a) /Bp (a) , whereas Φt becomes a free variable determined by the RFP self-organization processes. As a by product a correct expression for the resistive component of the toroidal loop voltage is given. The two port model obtained is finally closed by adding the poloidal and toroidal power supply networks and evolved by means of a SPICE simulator. The results enlighten some peculiarities found in the RFP transient operations: RFP startup and formation, pulsed poloidal current drive (PPCD) and oscillating field current drive (OFCD).

  10. The Influence of Magnetic Permeability on the Configuration of Magnetic Field in Helimak Device

    Institute of Scientific and Technical Information of China (English)

    陈文革; 武松涛

    2003-01-01

    The Helimak of USA is a plasma physics experimental device designed and builtby CASIPP. Its configuration of magnetic field is of very importance during the operation of thisdevice. In this paper, the influence of magnetic permeability on configuration of magnetic field willbe discussed due to the effect of weld metal in the vacuum vessel of Helimak, and some conclusionis useful for some engineering designs of the fusion experimental device.

  11. The magnetic field configuration of a solar prominence inferred from spectropolarimetric observations in the He I 10830 A triplet

    CERN Document Server

    Suárez, David Orozco; Bueno, Javier Trujillo

    2014-01-01

    Context: The determination of the magnetic field vector in quiescent solar prominences is possible by interpreting the Hanle and Zeeman effects in spectral lines. However, observational measurements are scarce and lack high spatial resolution. Aims: To determine the magnetic field vector configuration along a quiescent solar prominence by interpreting spectropolarimetric measurements in the He I 1083.0 nm triplet obtained with the Tenerife Infrared Polarimeter installed at the German Vacuum Tower Telescope of the Observatorio del Teide. Methods. The He I 1083.0 nm triplet Stokes profiles are analyzed with an inversion code that takes into account the physics responsible of the polarization signals in this triplet. The results are put into a solar context with the help of extreme ultraviolet observations taken with the Solar Dynamic Observatory and the Solar Terrestrial Relations Observatory satellites. Results: For the most probable magnetic field vector configuration, the analysis depicts a mean field streng...

  12. Reynolds stress flow shear and turbulent energy transfer in reversed field pinch configuration

    Science.gov (United States)

    Vianello, Nicola; Spolaore, Monica; Serianni, Gianluigi; Regnoli, Giorgio; Spada, Emanuele; Antoni, Vanni; Bergsåker, Henric; Drake, James R.

    2003-10-01

    The role of Reynolds Stress tensor on flow generation in turbulent fluids and plasmas is still an open question and the comprehension of its behavior may assist the understanding of improved confinement scenario. It is generally believed that shear flow generation may occur by an interaction of the turbulent Reynolds stress with the shear flow. It is also generally believed that this mechanism may influence the generation of zonal flow shears. The evaluation of the complete Reynolds Stress tensor requires contemporary measurements of its electrostatic and magnetic part: this requirement is more restrictive for Reversed Field Pinch configuration where magnetic fluctuations are larger than in tokamak . A new diagnostic system which combines electrostatic and magnetic probes has been installed in the edge region of Extrap-T2R reversed field pinch. With this new probe the Reynolds stress tensor has been deduced and its radial profile has been reconstructed on a shot to shot basis exploring differen plasma conditions. These profiles have been compared with the naturally occurring velocity flow profile, in particular during Pulsed Poloidal Current Drive experiment, where a strong variation of ExB flow radial profile has been registered. The study of the temporal evolution of Reynolds stress reveals the appearance of strong localized bursts: these are considered in relation with global MHD relaxation phenomena, which naturally occur in the core of an RFP plasma sustaining its configuration.

  13. Extended magnetohydrodynamic simulations of field reversed configuration formation and sustainment with rotating magnetic field current drive

    Science.gov (United States)

    Milroy, R. D.; Kim, C. C.; Sovinec, C. R.

    2010-06-01

    Three-dimensional simulations of field reversed configuration (FRC) formation and sustainment with rotating magnetic field (RMF) current drive have been performed with the NIMROD code [C. R. Sovinec et al., J. Comput. Phys. 195, 355 (2004)]. The Hall term is a zeroth order effect with strong coupling between Fourier components, and recent enhancements to the NIMROD preconditioner allow much larger time steps than was previously possible. Boundary conditions to capture the effects of a finite length RMF antenna have been added, and simulations of FRC formation from a uniform background plasma have been performed with parameters relevant to the translation, confinement, and sustainment-upgrade experiment at the University of Washington [H. Y. Guo, A. L. Hoffman, and R. D. Milroy, Phys. Plasmas 14, 112502 (2007)]. The effects of both even-parity and odd-parity antennas have been investigated, and there is no evidence of a disruptive instability for either antenna type. It has been found that RMF effects extend considerably beyond the ends of the antenna, and that a large n =0 Bθ can develop in the open-field line region, producing a back torque opposing the RMF.

  14. Entanglement and coherence of a three-level atom in Λ configuration interacting with two fields

    Institute of Scientific and Technical Information of China (English)

    Zhang Jian-Song; Xu Jing-Bo

    2009-01-01

    We investigate the entanglement of a three-level atom in A configuration interacting with two quantized field modes by using logarithmic negativity. Then, we study the relationship of the atomic coherence and the entanglement between two fields which are initially prepared in vacuum or thermal states. We find that if the two fields are prepared in thermal states, the atomic coherence can induce the entanglement between two thermal fields. However, there is no coherence-induced entanglement between two vacuum fields.

  15. Principal physics of rotating magnetic-field current drive of field reversed configurations

    Science.gov (United States)

    Hoffman, A. L.; Guo, H. Y.; Miller, K. E.; Milroy, R. D.

    2006-01-01

    After extensive experimentation on the Translation, Confinement, and Sustainment rotating magnetic-field (RMF)-driven field reversed configuration (FRC) device [A. L. Hoffman et al., Fusion Sci. Technol. 41, 92 (2002)], the principal physics of RMF formation and sustainment of standard prolate FRCs inside a flux conserver is reasonably well understood. If the RMF magnitude Bω at a given frequency ω is high enough compared to other experimental parameters, it will drive the outer electrons of a plasma column into near synchronous rotation, allowing the RMF to penetrate into the plasma. If the resultant azimuthal current is strong enough to reverse an initial axial bias field Bo a FRC will be formed. A balance between the RMF applied torque and electron-ion friction will determine the peak plasma density nm∝Bω/η1/2ω1/2rs, where rs is the FRC separatrix radius and η is an effective weighted plasma resistivity. The plasma total temperature Tt is free to be any value allowed by power balance as long as the ratio of FRC diamagnetic current, I'dia≈2Be/μo, is less than the maximum possible synchronous current, I'sync=⟨ne⟩eωrs2/2. The RMF will self-consistently penetrate a distance δ* governed by the ratio ζ =I'dia/I'sync. Since the FRC is a diamagnetic entity, its peak pressure pm=nmkTt determines its external magnetic field Be≈(2μopm)1/2. Higher FRC currents, magnetic fields, and poloidal fluxes can thus be obtained, with the same RMF parameters, simply by raising the plasma temperature. Higher temperatures have also been noted to reduce the effective plasma resistivity, so that these higher currents can be supported with surprisingly little increase in absorbed RMF power.

  16. Far infrared laser polarimetry and far forward scattering diagnostics for the C-2 field reversed configuration plasmas.

    Science.gov (United States)

    Deng, B H; Kinley, J S; Knapp, K; Feng, P; Martinez, R; Weixel, C; Armstrong, S; Hayashi, R; Longman, A; Mendoza, R; Gota, H; Tuszewski, M

    2014-11-01

    A two-chord far infrared (FIR) laser polarimeter for high speed sub-degree Faraday rotation measurements in the C-2 field reversed configuration experiment is described. It is based on high power proprietary FIR lasers with line width of about 330 Hz. The exceptionally low intrinsic instrument phase error is characterized with figures of merit. Significant toroidal magnetic field with rich dynamics is observed. Simultaneously obtained density fluctuation spectra by far forward scattering are presented.

  17. Detection and Analysis of X Ray Emission from the Princeton-Field-Reversed Configuration (PFRC-2)

    Science.gov (United States)

    Bosh, Alexandra; Swanson, Charles; Jandovitz, Peter; Cohen, Samuel

    2016-10-01

    The PFRC is an odd-parity rotating-magnetic-field-driven field-reversed-configuration magnetic confinement experiment. Studying X rays produced via electron Bremsstrahlung with neutral particles is crucial to the further understanding of the energy and particle confinement of the PFRC. The data on the x rays are collected using a detector system comprised of two, spatially scannable Amptek XR-100 CR detectors and a Amptek XR-100 SDD detector that view the plasma column at two axial locations, one in the divertor and one near the axial midplane. These provide X-ray energy and arrival-time information. (Data analysis requires measurement of each detector's efficiency, a parameter that is modified by window transmission. Detector calibrations were performed with a custom-made X-ray tube that impinged 1-microamp 1-5 kV electron beams onto a carbon target.) From the analyzed data, the average electron energy, effective temperature, and electron density can be extracted. Spatial scans then allow the FRC's internal energy to be measured. We present recent measurements of the Bremsstrahlung spectrum from 0.8 to 6 keV and the inferred electron temperature in the PFRC device as functions of heating power, magnetic field and fill gas pressure. This work was supported, in part, by DOE Contract Number DE-AC02-09CH11466.

  18. A Toy Model for Magnetic Field Configurations in Black Hole Accretion Discs

    Institute of Scientific and Technical Information of China (English)

    GE Zhao-Jiang; WANG Ding-Xiong; LEI Wei-Hua

    2008-01-01

    We discuss the feature of the magnetic field configuration arising from double counter oriented electric current-rings in the accretion disc around a Kerr black hole (BH). We discuss the relevant physical quantities corresponding to this configuration: (1) the power and torque transferred by the large-scale magnetic field, (2) the angular momentum and energy fluxes transferred from the BH to the inner disc, (3) the radiation flux from the disc. In addition, we discuss the possibility that the closed magnetic field anchored at the disc probably evolves to the open magnetic field, which is helpful to produce the jet from the disc.

  19. On the Stability of Quasi-Equilibrium Self-Gravitating Configurations in a Tidal Field

    CERN Document Server

    Domínguez-Tenreiro, R

    2000-01-01

    The possibility that quasi-equilibrium self-gravitating galaxy-like configurations exist in a tidal field is analyzed in this paper. More specifically, we address the question of how to predict initial configurations modeling galaxies that are able to survive environmental effects in a dense environment for a Hubble time or so, provided thay dynamical friction is neglected. The initial quasi-equilibrium configurations have been built up taking into account the external tidal field produced by the halo. It modifies the escape velocity field of the configuration, compared with isolated configurations. The survival of the configurations as they orbit inside the halos has been studied through N-body simulations. As a general result, it has been found out that the bulk of the models is conserved along 12.5 Gyears of evolution, and that the low rates of mass losses they experience are consistent with those expected when the adiabatic protection hypothesis is at work. So, solutions for galaxy configurations in tidal...

  20. Measuring 3D Point Configurations in Pictorial Space

    Directory of Open Access Journals (Sweden)

    Johan Wagemans

    2011-01-01

    Full Text Available We propose a novel method to probe the depth structure of the pictorial space evoked by paintings. The method involves an exocentric pointing paradigm that allows one to find the slope of the geodesic connection between any pair of points in pictorial space. Since the locations of the points in the picture plane are known, this immediately yields the depth difference between the points. A set of depth differences between all pairs of points from an N-point (N > 2 configuration then yields the configuration in depth up to an arbitrary depth offset. Since an N-point configuration implies N(N-1 (ordered pairs, the number of observations typically far exceeds the number of inferred depths. This yields a powerful check on the geometrical consistency of the results. We report that the remaining inconsistencies are fully accounted for by the spread encountered in repeated observations. This implies that the concept of ‘pictorial space’ indeed has an empirical significance. The method is analyzed and empirically verified in considerable detail. We report large quantitative interobserver differences, though the results of all observers agree modulo a certain affine transformation that describes the basic cue ambiguities. This is expected on the basis of a formal analysis of monocular optical structure. The method will prove useful in a variety of potential applications.

  1. Pure Gauge Configurations and Tachyon Solutions to String Field Theories Equations of Motion

    CERN Document Server

    Aref'eva, I Ya; Grigoryev, D A; Khromov, P N; Maltsev, M V; Medvedev, P B

    2009-01-01

    In constructions of analytical solutions to open string field theories pure gauge configurations parameterized by wedge states play an essential role. These pure gauge configurations are constructed as perturbation expansions and to guaranty that these configurations are asymptotical solutions to equations of motions one needs to study convergence of the perturbation expansions. We demonstrate that for the large parameter of the perturbation expansion these pure gauge truncated configurations give divergent contributions to the equation of motion on the subspace of the wedge states. We perform this demonstration numerically for the pure gauge configurations related to tachyon solutions for the bosonic and the NS fermionic SFT. By the numerical calculations we also show that the perturbation expansions are cured by adding extra terms. These terms are nothing but the terms necessary to make valued the Sen conjectures.

  2. Vortex configuration in the presence of local magnetic field and locally applied stress

    Energy Technology Data Exchange (ETDEWEB)

    Wissberg, Shai; Kremen, Anna; Shperber, Yishai; Kalisky, Beena, E-mail: beena@biu.ac.il

    2017-02-15

    Highlights: • We discuss different ways to determine vortex configuration using a scanning SQUID. • We determined the vortex configuration by approaching the sample during cooling. • We observed an accumulation of vortices when contact was made with the sample. • We show how we can manipulate local vortex configuration using contact. - Abstract: Vortex configuration is determined by the repulsive interaction, which becomes dominant with increasing vortex density, by the pinning potential, and by other considerations such as the local magnetic fields, currents flowing in the sample, or as we showed recently, by local stress applied on the sample. In this work we describe different ways to control vortex configuration using scanning SQUID microscopy.

  3. FIELD STRENGTH MEASUREMENTS, PHASE II.

    Science.gov (United States)

    The measurement of the strength of radio frequency fields at high frequency and above has followed practices which are standard for the measurement...of field strength at medium and low frequencies. Variability of measurements made in practical situations and a lack of reproducibility of...measurements made under apparently identical conditions has prompted an investigation of equipment and methods used in the determinations. The field strength

  4. Hanle Effect Diagnostics of the Coronal Magnetic Field - A Test Using Realistic Magnetic Field Configurations

    CERN Document Server

    Raouafi, N -E; Wiegelmann, T

    2008-01-01

    Our understanding of coronal phenomena, such as coronal plasma thermodynamics, faces a major handicap caused by missing coronal magnetic field measurements. Several lines in the UV wavelength range present suitable sensitivity to determine the coronal magnetic field via the Hanle effect. The latter is a largely unexplored diagnostic of coronal magnetic fields with a very high potential. Here we study the magnitude of the Hanle-effect signal to be expected outside the solar limb due to the Hanle effect in polarized radiation from the H {\\sc{i}} Ly$\\alpha$ and $\\beta$ lines, which are among the brightest lines in the off-limb coronal FUV spectrum. For this purpose we use a magnetic field structure obtained by extrapolating the magnetic field starting from photospheric magnetograms. The diagnostic potential of these lines for determining the coronal magnetic field, as well as their limitations are studied. We show that these lines, in particular H {\\sc{i}} Ly$\\beta$, are useful for such measurements.

  5. Relativistic models of magnetars: the twisted-torus magnetic field configuration

    CERN Document Server

    Ciolfi, R; Gualtieri, L; Pons, J A

    2009-01-01

    We find general relativistic solutions of equilibrium magnetic field configurations in magnetars, extending previous results of Colaiuda et al. (2008). Our method is based on the solution of the relativistic Grad-Shafranov equation, to which Maxwell's equations can be reduced in some limit. We obtain equilibrium solutions with the toroidal magnetic field component confined into a finite region inside the star, and the poloidal component extending to the exterior. These so-called twisted-torus configurations have been found to be the final outcome of dynamical simulations in the framework of Newtonian gravity, and appear to be more stable than other configurations. The solutions include higher order multipoles, which are coupled to the dominant dipolar field. We use arguments of minimal energy to constrain the ratio of the toroidal to the poloidal field.

  6. Impact of the strong electromagnetic field on the QCD effective potential for homogeneous Abelian gluon field configurations

    CERN Document Server

    Galilo, Bogdan V

    2011-01-01

    The one-loop quark contribution to the QCD effective potential for the homogeneous Abelian gluon field in the presence of external strong electromagnetic field is evaluated. The structure of extrema of the potential as a function of the angles between chromoelectric, chromomagnetic and electromagnetic fields is analyzed. In this setup, the electromagnetic field is considered as an external one while the gluon field represents domain structured nonperturbative gluon configurations related to the QCD vacuum in the confinement phase. Two particularly interesting gluon configurations, (anti-)self-dual and crossed orthogonal chromomagnetic and chromoelectric fields, are discussed specifically. Within this simplified framework it is shown that the strong electromagnetic fields can play a catalysing role for a deconfinement transition. At the qualitative level, the present consideration can be seen as a highly simplified study of an impact of the electromagnetic fields generated in relativistic heavy ion collisions ...

  7. High-field bipolar loss measurement apparatus

    Energy Technology Data Exchange (ETDEWEB)

    Thullen, P.; Weldon, D.; Wollan, J.

    1980-01-01

    An apparatus was constructed to measure dissipation in superconducting wire in high alternating fields. The apparatus will be used to make measurements on conductors which must operate in fields up to 7.0 T and rates of field change up to 15 T/s. The magnet for this facility is wound of uninsulated, 15 strand Rutherford cable in which the strand is a 0.812 mm diameter, fully mixed matrix, Cu plus CuNi, multifilament NbTi conductor. The coil is wound in a bath cooled configuration with an overall current density of 7.8 kA/cm/sup 2/. The circuit incorporates a pair of locomotive traction motors as the capacitive circuit element for the bipolar swing. The design, construction and operating characteristics of the field coil and the associated circuitry are described.

  8. Langmuir probe diagnostic suite in the C-2 field-reversed configuration

    Science.gov (United States)

    Roche, T.; Sun, X.; Armstrong, S.; Knapp, K.; Slepchenkov, M.

    2014-11-01

    Several in situ probes have been designed and implemented into the diagnostic array of the C-2 field-reversed configuration (FRC) at Tri Alpha Energy [M. Tuszewski et al. (the TAE Team), Phys. Rev. Lett. 108, 255008 (2012)]. The probes are all variations on the traditional Langmuir probe. They include linear arrays of triple probes, linear arrays of single-tipped swept probes, a multi-faced Gundestrup probe, and an ion-sensitive probe. The probes vary from 5 to 7 mm diameter in size to minimize plasma perturbations. They also have boron nitride outer casings that prevent unwanted electrical breakdown and reduce the introduction of impurities. The probes are mounted on motorized linear-actuators allowing for programmatic scans of the various plasma parameters over the course of several shots. Each probe has a custom set of electronics that allows for measurement of the desired signals. High frequency ( > 5MHz) analog optical-isolators ensure that plasma parameters can be measured at sub-microsecond time scales while providing electrical isolation between machine and data acquisition systems. With these probes time-resolved plasma parameters (temperature, density, spatial potential, flow, and electric field) can be directly/locally measured in the FRC jet and edge/scrape-off layer.

  9. 3D magnetic field configuration of small-scale reconnection events in the solar plasma atmosphere

    Energy Technology Data Exchange (ETDEWEB)

    Shimizu, T., E-mail: shimizu@solar.isas.jaxa.jp [Institute of Space and Astronautical Science, Japan Aerospace Exploration Agency, 3-1-1 Yoshinodai, Chuo-ku, Sagamihara, Kanagawa 252-5210 (Japan); Department of Earth and Planetary Science, The University of Tokyo, 7-3-1 Hongo, Bunkyo-ku, Tokyo 113-0033 (Japan)

    2015-10-15

    The outer solar atmosphere, i.e., the corona and the chromosphere, is replete with small energy-release events, which are accompanied by transient brightening and jet-like ejections. These events are considered to be magnetic reconnection events in the solar plasma, and their dynamics have been studied using recent advanced observations from the Hinode spacecraft and other observatories in space and on the ground. These events occur at different locations in the solar atmosphere and vary in their morphology and amount of the released energy. The magnetic field configurations of these reconnection events are inferred based on observations of magnetic fields at the photospheric level. Observations suggest that these magnetic configurations can be classified into two groups. In the first group, two anti-parallel magnetic fields reconnect to each other, yielding a 2D emerging flux configuration. In the second group, helical or twisted magnetic flux tubes are parallel or at a relative angle to each other. Reconnection can occur only between anti-parallel components of the magnetic flux tubes and may be referred to as component reconnection. The latter configuration type may be more important for the larger class of small-scale reconnection events. The two types of magnetic configurations can be compared to counter-helicity and co-helicity configurations, respectively, in laboratory plasma collision experiments.

  10. FIELD STRENGTH MEASUREMENTS, PHASE I.

    Science.gov (United States)

    The program included the testing and evaluation of commercial and military field- strength meters. It also included a study of the interpretation of...field- strength measurement data taken under multipath conditions. As part of the field- strength meter evaluation, five instruments, the AN/TRM-7, NF...interpretation of the measured data is the variability of field- strength values obtained over an area. Such variability is caused by the presence of multipath

  11. ac transmission line field measurements

    Energy Technology Data Exchange (ETDEWEB)

    Kotter, F.R.; Misakian, M.

    1977-11-01

    The concern in recent years over the environmental effects of electric and magnetic fields from high voltage transmission lines has also focused attention on the accuracy of measurements of these fields. Electric field meters are discussed in terms of theory of operation, parameters affecting performance, meter performance under field and laboratory conditions, and calibration procedures. The performance and calibration of magnetic field meters is described. (LCL)

  12. 3D magnetic field configuration of small-scale reconnection events in the solar plasma atmosphere

    CERN Document Server

    Shimizu, T

    2015-01-01

    The outer solar atmosphere, i.e., the corona and the chromosphere, is replete with small energy-release events, which are accompanied by transient brightening and jet-like ejections. These events are considered to be magnetic reconnection events in the solar plasma, and their dynamics have been studied using recent advanced observations from the Hinode spacecraft and other observatories in space and on the ground. These events occur at different locations in the solar atmosphere, and vary in their morphology and amount of the released energy. The magnetic field configurations of these reconnection events are inferred based on observations of magnetic fields at the photospheric level. Observations suggest that these magnetic configurations can be classified into two groups. In the first group, two anti-parallel magnetic fields reconnect to each other, yielding a 2D emerging flux configuration. In the second group, helical or twisted magnetic flux tubes are parallel or at a relative angle to each other. Reconne...

  13. Local field distribution and configuration of CO molecules adsorbed on the nanostructure platinum surface

    Institute of Scientific and Technical Information of China (English)

    Huang Xiao-Jing; He Su-Zhen; Wu Chen-Xu

    2006-01-01

    This paper shows that the local electric field distribution near the nanostructure metallic surface is obtained by solving the Laplace equation, and furthermore, the configuration of CO molecules adsorbed on a Pt nanoparticle surface is obtained by using Monte Carlo simulation. It is found that the uneven local electric field distribution induced by the nanostructure surface can influence the configuration of carbon monoxide (CO) molecules by a force, which drags the adsorbates to the poles of the nanoparticles. This result, together with our results obtained before, may explain the experimental results that the nanostructure metallic surface can lead to abnormal phenomena such as anti-absorption infrared effects.

  14. Reliable measurements for an image-derived sample volume in an open-configuration MR system

    Science.gov (United States)

    Han, Bong Soo; Lee, Man Woo; Hong, Cheolpyo

    2016-11-01

    Open-configuration magnetic resonance (MR) systems are becoming desirable for volume measurements of off-center samples due to their non-claustrophobic system configuration, excellent soft-tissue contrast, high efficiency, and low-cost. However, geometric distortion is produced by the unwanted background magnetic field and hinders volume measurements. The present study describes the characteristics of geometric distortion in off-center samples such as the thigh muscle and adipose tissue measurements using an open-type MR system. The American Association of Physicists in Medicine uniformity and linearity phantom was used for the detection and the evaluation of the geometric distortion. The geometric distortion decreased near the isocenter and increased toward the off-center. A cylindrical phantom image was acquired at the isocenter and was used as the distortion-free, reference image. Two cylindrical phantoms were scanned off-center at a position analogous to that of the human thigh. The differences between the two cylindrical phantom volumes and the reference volume were 1.62 % ± 0.16 and 5.18 % ± 0.14. Off-center-related MR imaging requires careful consideration for image interpretation and volumetric assessment of tissue.

  15. Effects of magnetic field configuration on rf sputtering for CdS/CdTe solar cells

    Energy Technology Data Exchange (ETDEWEB)

    Compaan, A.; Shao, M.; Fischer, A.; Grecu, D.; Jayamaha, U.; Contreras-Puente, G.; Bohn, R.G. [Univ. of Toledo, OH (United States)

    1996-12-31

    The authors report studies of solar cells prepared by rf planar magnetron sputtering in which the films were deposited using magnetic field structures ranging from approximately balanced to strongly unbalanced in the type II configuration. For films grown with the unbalanced configurations, they find much stronger photoluminescence and much better cell performance than for the balanced configuration. The CdTe films show differences in electrical performance depending on magnetic field as well. These effects are interpreted as arising from the enhanced electron and ion bombardment of the film growth interface for the unbalanced magnetrons. Using two unbalanced magnetrons the authors have fabricated an all-rf-sputtered cell with NREL-verified efficiency of 11.6% at air mass 1.5 illumination.

  16. Field configuring events shaping sustainability transitions? The case of solar PV in India

    NARCIS (Netherlands)

    Jolly, Suyash; Raven, R.P.J.M.

    2016-01-01

    Abstract The sustainability transitions literature has emphasized the analytical challenges in understanding the trade-offs in protecting niche innovations. This paper builds on an emerging body of literature that argues that the concept of field-configuring events (FCE) is useful for understanding

  17. Testing Circuit Models for the Energies of Coronal Magnetic Field Configurations

    CERN Document Server

    Wheatland, M S

    2003-01-01

    Circuit models involving bulk currents and inductances are often used to estimate the energies of coronal magnetic field configurations, in particular configurations associated with solar flares. The accuracy of circuit models is tested by comparing calculated energies of linear force-free fields with specified boundary conditions with corresponding circuit estimates. The circuit models are found to provide reasonable (order of magnitude) estimates for the energies of the non-potential components of the fields, and to reproduce observed functional dependences of the energies. However, substantial departure from the circuit estimates is observed for large values of the force-free parameter, and this is attributed to the influence of the non-potential component of the field on the path taken by the current.

  18. Simulation of drift wave instability in field-reversed configurations using global magnetic geometry

    Science.gov (United States)

    Fulton, D. P.; Lau, C. K.; Lin, Z.; Tajima, T.; Holod, I.; the TAE Team

    2016-10-01

    Minimizing transport in the field-reversed configuration (FRC) is essential to enable FRC-based fusion reactors. Recently, significant progress on advanced beam-driven FRCs in C-2 and C-2U (at Tri Alpha Energy) provides opportunities to study transport properties using Doppler backscattering (DBS) measurements of turbulent fluctuations and kinetic particle-in-cell simulations of driftwaves in realistic equilibria via the Gyrokinetic Toroidal Code (GTC). Both measurements and simulations indicate relatively small fluctuations in the scrape-off layer (SOL). In the FRC core, local, single flux surface simulations reveal strong stabilization, while experiments indicate quiescent but finite fluctuations. One possible explanation is that turbulence may originate in the SOL and propagate at very low levels across the separatrix into the core. To test this hypothesis, a significant effort has been made to develop A New Code (ANC) based on GTC physics formulations, but using cylindrical coordinates which span the magnetic separatrix, including both core and SOL. Here, we present first results from global ANC simulations.

  19. Measurement of the Clinical Usability of a Configurable EHR

    DEFF Research Database (Denmark)

    Møller-Jensen, John; Lund Pedersen, Ivan; Simonsen, Jesper

    2006-01-01

    requested by the clinicians focused on improving their overview and assessment of patients as well as on more efficient coordination in three specific and highly cooperative situations, viz. nursing handover, ward round and patient conference. All three situations were measured before (using paper......, observations, and Task Load Index (TLX) ratings. In total, 15 nursing handovers, 8 ward rounds, and 11 patient conferences involving a total of 35 patients and more than 20 clinicians were included in the measurements. Data from the project has been comparatively analysed by means of the TLX scores. Our...

  20. Measuring Effects on the Clinical Practice from a Configured EHR

    DEFF Research Database (Denmark)

    Møller-Jensen, John; Simonsen, Jesper; K. Iversen, Rikke

    2006-01-01

    and acquired using various techniques including questionnaires, interviews, observations, and Task Load Index (TLX) ratings. In total, 15 nursing handovers, 8 ward rounds, and 11 patient conferences involving a total of 35 patients and more than 20 clinicians were included in the measurements. Data from...

  1. Measuring Earth's Magnetic Field Simply.

    Science.gov (United States)

    Stewart, Gay B.

    2000-01-01

    Describes a method for measuring the earth's magnetic field using an empty toilet paper tube, copper wire, clear tape, a battery, a linear variable resistor, a small compass, cardboard, a protractor, and an ammeter. (WRM)

  2. Field fluctuations measured by interferometry

    Energy Technology Data Exchange (ETDEWEB)

    Glauber, R J [Lyman Laboratory, Harvard University, Cambridge, MA 02138 (United States); Orozco, L A [Joint Quantum Institute, Department of Physics, University of Maryland and National Institute of Standards and Technology, College Park, MD 20742-4111 (United States); Vogel, K; Schleich, W P [Institut fuer Quantenphysik, Universitaet Ulm, D-89069 Ulm (Germany); Walther, H, E-mail: glauber@physics.harvard.ed, E-mail: karl.vogel@uni-ulm.d [Max-Planck-Institut fuer Quantenoptik, Hans-Kopfermann-Strasse 1, D-85748 Garching (Germany)

    2010-09-01

    We derive the complete photon count statistics of an interferometer based on two beam splitters. As a special case we consider a joint intensity-electric field measurement. Our approach is based on the transformation properties of state vectors as well as field operators at a beam splitter.

  3. Statistical-mechanics-inspired optimization of sensor field configuration for detection of mobile targets.

    Science.gov (United States)

    Mukherjee, Kushal; Gupta, Shalabh; Ray, Asok; Wettergren, Thomas A

    2011-06-01

    This paper presents a statistical-mechanics-inspired procedure for optimization of the sensor field configuration to detect mobile targets. The key idea is to capture the low-dimensional behavior of the sensor field configurations across the Pareto front in a multiobjective scenario for optimal sensor deployment, where the nondominated points are concentrated within a small region of the large-dimensional decision space. The sensor distribution is constructed using location-dependent energy-like functions and intensive temperature-like parameters in the sense of statistical mechanics. This low-dimensional representation is shown to permit rapid optimization of the sensor field distribution on a high-fidelity simulation test bed of distributed sensor networks.

  4. Optimizing bioimpedance measurement configuration for dual-gated nuclear medicine imaging: a sensitivity study.

    Science.gov (United States)

    Koivumäki, Tuomas; Vauhkonen, Marko; Kuikka, Jyrki T; Hakulinen, Mikko A

    2011-07-01

    Motion artefacts due to respiration and cardiac contractions may deteriorate the quality of nuclear medicine imaging leading to incorrect diagnosis and inadequate treatment. Motion artefacts can be minimized by simultaneous respiratory and cardiac gating, dual-gating. Currently, only cardiac gating is often performed. In this study, an optimized bioimpedance measurement configuration was determined for simultaneous respiratory and cardiac gating signal acquisition. The optimized configuration was located on anterolateral upper thorax based on sensitivity simulations utilizing a simplified thorax model. The validity of the optimized configuration was studied with six healthy volunteers. In the peak-to-peak and frequency content analyses the optimized configuration showed consistently higher peak-to-peak values and frequency content than other studied measurement configurations. This study indicates that the bioimpedance method has potential for the dual-gating in nuclear medicine imaging. The method would minimize the need of additional equipment, is easy for the technologists to use and comfortable for the patients.

  5. Non-Abelian fields in AdS$_4$ spacetime: axially symmetric, composite configurations

    CERN Document Server

    Kichakova, Olga; Radu, Eugen; Shnir, Yasha

    2014-01-01

    We construct new finite energy regular solutions in Einstein-Yang-Mills-SU(2) theory. They are static, axially symmetric and approach at infinity the anti-de Sitter spacetime background. These configurations are characterized by a pair of integers $(m, n)$, where $m$ is related to the polar angle and $n$ to the azimuthal angle, being related to the known flat space monopole-antimonopole chains and vortex rings. Generically, they describe composite configurations with several individual components, possesing a nonzero magnetic charge, even in the absence of a Higgs field. Such Yang-Mills configurations exist already in the probe limit, the AdS geometry supplying the attractive force needed to balance the repulsive force of Yang-Mills gauge interactions. The gravitating solutions are constructed by numerically solving the elliptic Einstein-DeTurck--Yang-Mills equations. The variation of the gravitational coupling constant $\\alpha$ reveals the existence of two branches of gravitating solutions which bifurcate at...

  6. Measurement of carbonaceous aerosol with different sampling configurations and frequencies

    Science.gov (United States)

    Cheng, Y.; He, K.-B.

    2015-07-01

    A common approach for measuring the mass of organic carbon (OC) and elemental carbon (EC) in airborne particulate matter involves collection on a quartz fiber filter and subsequent thermal-optical analysis. Although having been widely used in aerosol studies and in PM2.5 (fine particulate matter) chemical speciation monitoring networks in particular, this measurement approach is prone to several types of artifacts, such as the positive sampling artifact caused by the adsorption of gaseous organic compounds onto the quartz filter, the negative sampling artifact due to the evaporation of OC from the collected particles and the analytical artifact in the thermal-optical determination of OC and EC (which is strongly associated with the transformation of OC into char OC and typically results in an underestimation of EC). The presence of these artifacts introduces substantial uncertainties to observational data on OC and EC and consequently limits our ability to evaluate OC and EC estimations in air quality models. In this study, the influence of sampling frequency on the measurement of OC and EC was investigated based on PM2.5 samples collected in Beijing, China. Our results suggest that the negative sampling artifact of a bare quartz filter could be remarkably enhanced due to the uptake of water vapor by the filter medium. We also demonstrate that increasing sampling duration does not necessarily reduce the impact of positive sampling artifact, although it will enhance the analytical artifact. Due to the effect of the analytical artifact, EC concentrations of 48 h averaged samples were about 15 % lower than results from 24 h averaged ones. In addition, it was found that with the increase of sampling duration, EC results exhibited a stronger dependence on the charring correction method and, meanwhile, optical attenuation (ATN) of EC (retrieved from the carbon analyzer) was more significantly biased by the shadowing effect. Results from this study will be useful for the

  7. Intermediate regime of charged particle scattering in the field-reversal configuration

    Energy Technology Data Exchange (ETDEWEB)

    Shustov, P. I., E-mail: p.shustov@gmail.com; Yushkov, E. V. [Space Research Institute, RAS, Profsouznaya st., 84/32, GSP-7, 117997 Moscow (Russian Federation); Department of Physics, Moscow State University, 119992 Moscow (Russian Federation); Artemyev, A. V., E-mail: artemyev@iki.rssi.ru [Space Research Institute, RAS, Profsouznaya st., 84/32, GSP-7, 117997 Moscow (Russian Federation)

    2015-12-15

    In this paper, we investigate the charged particle scattering in the magnetic field configuration with stretched magnetic field lines. This scattering results from the violation of the adiabaticity of charged particle motion in the region with the strong gradient of the magnetic field. We consider the intermediate regime of charged particle dynamics, when the violation of the adiabaticity is significant enough, but particle motion is not chaotic. We demonstrate and describe the significant scattering of particles with large adiabatic invariants (magnetic moment). We discuss a possible application of obtained results for description of the peculiarities of pitch-angle diffusion of relativistic electrons in the Earth radiation belts.

  8. Field reversed configuration confinement enhancement through edge biasing and neutral beam injection.

    Science.gov (United States)

    Tuszewski, M; Smirnov, A; Thompson, M C; Korepanov, S; Akhmetov, T; Ivanov, A; Voskoboynikov, R; Schmitz, L; Barnes, D; Binderbauer, M W; Brown, R; Bui, D Q; Clary, R; Conroy, K D; Deng, B H; Dettrick, S A; Douglass, J D; Garate, E; Glass, F J; Gota, H; Guo, H Y; Gupta, D; Gupta, S; Kinley, J S; Knapp, K; Longman, A; Hollins, M; Li, X L; Luo, Y; Mendoza, R; Mok, Y; Necas, A; Primavera, S; Ruskov, E; Schroeder, J H; Sevier, L; Sibley, A; Song, Y; Sun, X; Trask, E; Van Drie, A D; Walters, J K; Wyman, M D

    2012-06-22

    Field reversed configurations (FRCs) with high confinement are obtained in the C-2 device by combining plasma gun edge biasing and neutral beam injection. The plasma gun creates an inward radial electric field that counters the usual FRC spin-up. The n = 2 rotational instability is stabilized without applying quadrupole magnetic fields. The FRCs are nearly axisymmetric, which enables fast ion confinement. The plasma gun also produces E × B shear in the FRC edge layer, which may explain the observed improved particle transport. The FRC confinement times are improved by factors 2 to 4, and the plasma lifetimes are extended from 1 to up to 4 ms.

  9. Guiding-center Hamiltonian figure-8 particles in axisymmetric field-reversed configurations

    Energy Technology Data Exchange (ETDEWEB)

    Mynick, H.E.

    1979-09-01

    The guiding-center Hamiltonian K is derived for so-called figure-8 particles which are present in field-reversed mirror configurations, using a formalism developed previously. For such particles, the gyro-orbit cannot be approximated by a circle, and standard approaches to guiding-center theory are thus totally inapplicable. K manifests this intrinsic difference by a quite different dependence on the gyroaction, and by familiar effects such as mirroring and magnetic-gradient drifts being controlled by the radial derivative of the magnetic field strength B at the point of field-reversal, rather than by B itself, as occurs in standard guiding-center theory.

  10. Fast Filtered Imaging of the C-2U Advanced Beam-Driven Field-Reversed Configuration

    Science.gov (United States)

    Granstedt, E. M.; Petrov, P.; Knapp, K.; Cordero, M.; Patel, V.; the TAE Team

    2015-11-01

    The goal of the C-2U program is to sustain a Field-Reversed Configuration (FRC) for 5+ ms using neutral beam injection, end-biasing, and various particle fueling techniques. Three high-speed, filtered cameras are used to observe visible light emission from deuterium pellet ablation and compact-toroid injection which are used for auxiliary particle fueling. The instruments are also used to view the dynamics of the macroscopic plasma evolution, identify regions of strong plasma-material interactions, and visualize non-axisymmetric perturbations. To achieve the necessary viewing geometry, imaging lenses are mounted in re-entrant viewports, two of which are mounted on bellows for retraction during gettering and removal if cleaning is necessary. Images are coupled from the imaging lens to the camera via custom lens-based optical periscopes. Each instrument contains a remote-controlled filter wheel which is set between shots to select a particular emission line from neutral D or various charge states of He, C, O, or Ti. Measurements of absolute emissivity and estimates of neutral and impurity density will be presented.

  11. Diagnosing the high density FRX-L Field Reversed Configuration plasma

    Science.gov (United States)

    Wurden, G. A.; Intrator, T. P.; Renneke, R. M.; Dorf, L. A.; Farrell, M. W.; Gray, T. K.; Hsu, S. C.; Lynn, A. G.; Ruden, E. L.

    2006-10-01

    The FRX-L plasma is a high pressure, high density, field reversed configuration (FRC), at n ˜1x10^16-1x10^17 cm-3, and hundreds of eV electron temperature. In order to study formation, equilibrium, transport, flow, and confinement issues, we have a suite of diagnostics. Standard plasma diagnostics include B-dot probes, magnetic flux loops, single and multi-channel visible spectroscopy, optical light tomography arrays, up to 8 filtered visible fibers (546 nm or 486 nm) and an 8-chord side-on HeNe interferometer. Recent diagnostic additions include AXUV bolometers, VUV spectroscopy using a methly salicylate fluorescer converter and optical multichannel analyzer (OMA), eight simultaneous axial views of visible spectra with a 0.3 meter spectrometer and Princeton Instruments PI-Max camera, two-foil end-on surface barrier diode soft x-ray measurements, a hard x-ray/neutron plastic scintillator/ PMT, and indium activation foils to detect time-integrated absolute DD neutron emission. We also discuss plans for a soft x-ray framing camera, using end-on optical access and consisting of a pinhole/fluorescer geometry coupled to a high resolution DiCam camera.

  12. High sensitivity far infrared laser diagnostics for the C-2U advanced beam-driven field-reversed configuration plasmas

    Energy Technology Data Exchange (ETDEWEB)

    Deng, B. H., E-mail: bdeng@trialphaenergy.com; Beall, M.; Schroeder, J.; Settles, G.; Feng, P.; Kinley, J. S.; Gota, H.; Thompson, M. C. [Tri Alpha Energy, Inc., P.O. Box 7010, Rancho Santa Margarita, California 92688 (United States)

    2016-11-15

    A high sensitivity multi-channel far infrared laser diagnostics with switchable interferometry and polarimetry operation modes for the advanced neutral beam-driven C-2U field-reversed configuration (FRC) plasmas is described. The interferometer achieved superior resolution of 1 × 10{sup 16} m{sup −2} at >1.5 MHz bandwidth, illustrated by measurement of small amplitude high frequency fluctuations. The polarimetry achieved 0.04° instrument resolution and 0.1° actual resolution in the challenging high density gradient environment with >0.5 MHz bandwidth, making it suitable for weak internal magnetic field measurements in the C-2U plasmas, where the maximum Faraday rotation angle is less than 1°. The polarimetry resolution data is analyzed, and high resolution Faraday rotation data in C-2U is presented together with direct evidences of field reversal in FRC magnetic structure obtained for the first time by a non-perturbative method.

  13. High sensitivity far infrared laser diagnostics for the C-2U advanced beam-driven field-reversed configuration plasmas

    Science.gov (United States)

    Deng, B. H.; Beall, M.; Schroeder, J.; Settles, G.; Feng, P.; Kinley, J. S.; Gota, H.; Thompson, M. C.

    2016-11-01

    A high sensitivity multi-channel far infrared laser diagnostics with switchable interferometry and polarimetry operation modes for the advanced neutral beam-driven C-2U field-reversed configuration (FRC) plasmas is described. The interferometer achieved superior resolution of 1 × 1016 m-2 at >1.5 MHz bandwidth, illustrated by measurement of small amplitude high frequency fluctuations. The polarimetry achieved 0.04° instrument resolution and 0.1° actual resolution in the challenging high density gradient environment with >0.5 MHz bandwidth, making it suitable for weak internal magnetic field measurements in the C-2U plasmas, where the maximum Faraday rotation angle is less than 1°. The polarimetry resolution data is analyzed, and high resolution Faraday rotation data in C-2U is presented together with direct evidences of field reversal in FRC magnetic structure obtained for the first time by a non-perturbative method.

  14. Final report for the field-reversed configuration power plant critical-issue scoping study

    Energy Technology Data Exchange (ETDEWEB)

    Santarius, John F.; Mogahed, Elsayed A.; Emmert, Gilbert A.; Khater, Hesham Y.; Nguyen, Canh N.; Ryzhkov, Sergei V.; Stubna, Michael D.; Steinhauer, Loren C.; Miley, George H.

    2001-03-01

    This report describes research in which a team from the Universities of Wisconsin, Washington, and Illinois performed a scoping study of critical issues for field-reversed configuration (FRC) power plants. The key tasks for this research were (1) systems analysis of deuterium-tritium (D-T) FRC fusion power plants, and (2) conceptual design of the blanket and shield module for an FRC fusion core.

  15. Simulation of leakage current measurement on medical devices using helmholtz coil configuration with different current flow

    Science.gov (United States)

    Sutanto, E.; Chandra, F.; Dinata, R.

    2017-05-01

    Leakage current measurement which can follow IEC standard for medical device is one of many challenges to be answered. The IEC 60601-1 has defined that the limit for a leakage current for Medical Device can be as low as 10 µA and as high as 500 µA, depending on which type of contact (applied part) connected to the patient. Most people are using ELCB (Earth-leakage circuit breaker) for safety purpose as this is the most common and available safety device in market. One type of ELCB devices is RCD (Residual Current Device) and this RCD type can measure the leakage current directly. This work will show the possibility on how Helmholtz Coil Configuration can be made to be like the RCD. The possibility is explored by comparing the magnetic field formula from each device, then it proceeds with a simulation using software EJS (Easy Java Simulation). The simulation will make sure the concept of magnetic field current cancellation follows the RCD concept. Finally, the possibility of increasing the measurement’s sensitivity is also analyzed. The sensitivity is needed to see the possibility on reaching the minimum leakage current limit defined by IEC, 0.01mA.

  16. Nonthermal plasmas around black holes, relevant collective modes, new configurations, and magnetic field amplification

    Science.gov (United States)

    Coppi, B.

    2017-03-01

    The radiation emission from Shining Black Holes is most frequently observed to have nonthermal features. It is therefore appropriate to consider relevant collective processes in plasmas surrounding black holes that contain high energy particles with nonthermal distributions in momentum space. A fluid description with significant temperature anisotropies is the simplest relevant approach. These anisotropies are shown to have a critical influence on: (a) the existence and characteristics of stationary plasma and field ring configurations, (b) the excitation of "thermo-gravitational modes" driven by temperature anisotropies and gradients that involve gravity and rotation, (c) the generation of magnetic fields over macroscopic scale distances, and (d) the transport of angular momentum.

  17. Nonthermal plasmas around black holes, relevant collective modes, new configurations, and magnetic field amplification

    Energy Technology Data Exchange (ETDEWEB)

    Coppi, B., E-mail: coppi@mit.edu [Massachusetts Institute of Technology (United States)

    2017-03-15

    The radiation emission from Shining Black Holes is most frequently observed to have nonthermal features. It is therefore appropriate to consider relevant collective processes in plasmas surrounding black holes that contain high energy particles with nonthermal distributions in momentum space. A fluid description with significant temperature anisotropies is the simplest relevant approach. These anisotropies are shown to have a critical influence on: (a) the existence and characteristics of stationary plasma and field ring configurations, (b) the excitation of “thermo-gravitational modes” driven by temperature anisotropies and gradients that involve gravity and rotation, (c) the generation of magnetic fields over macroscopic scale distances, and (d) the transport of angular momentum.

  18. Modeling of Resistive Wall Modes in Tokamak and Reversed Field Pinch Configurations of KTX

    Science.gov (United States)

    Han, Rui; Zhu, Ping; Bai, Wei; Lan, Tao; Liu, Wandong

    2016-10-01

    Resistive wall mode is believed to be one of the leading causes for macroscopic degradation of plasma confinement in tokamaks and reversed field pinches (RFP). In this study, we evaluate the linear RWM instability of Keda Torus eXperiment (KTX) in both tokamak and RFP configurations. For the tokamak configuration, the extended MHD code NIMROD is employed for calculating the dependence of the RWM growth rate on the position and conductivity of the vacuum wall for a model tokamak equilibrium of KTX in the large aspect-ratio approximation. For the RFP configuration, the standard formulation of dispersion relation for RWM based on the MHD energy principle has been evaluated for a cylindrical α- Θ model of KTX plasma equilibrium, in an effort to investigate the effects of thin wall on the RWM in KTX. Full MHD calculations of RWM in the RFP configuration of KTX using the NIMROD code are also being developed. Supported by National Magnetic Confinement Fusion Science Program of China Grant Nos. 2014GB124002, 2015GB101004, 2011GB106000, and 2011GB106003.

  19. A new high performance field reversed configuration operating regime in the C-2 device

    Energy Technology Data Exchange (ETDEWEB)

    Tuszewski, M.; Smirnov, A.; Thompson, M. C.; Barnes, D.; Binderbauer, M. W.; Brown, R.; Bui, D. Q.; Clary, R.; Conroy, K. D.; Deng, B. H.; Dettrick, S. A.; Douglass, J. D.; Garate, E.; Glass, F. J.; Gota, H.; Guo, H.Y.; Gupta, D.; Gupta, S.; Kinley, J. S.; Knapp, K. [Tri Alpha Energy, Inc., P.O. Box 7010, Rancho Santa Margarita, California 92688 (United States); and others

    2012-05-15

    Large field reversed configurations (FRCs) are produced in the C-2 device by combining dynamic formation and merging processes. The good confinement of these FRCs must be further improved to achieve sustainment with neutral beam (NB) injection and pellet fuelling. A plasma gun is installed at one end of the C-2 device to attempt electric field control of the FRC edge layer. The gun inward radial electric field counters the usual FRC spin-up and mitigates the n = 2 rotational instability without applying quadrupole magnetic fields. Better plasma centering is also obtained, presumably from line-tying to the gun electrodes. The combined effects of the plasma gun and of neutral beam injection lead to the high performance FRC operating regime, with FRC lifetimes up to 3 ms and with FRC confinement times improved by factors 2 to 4.

  20. Special ESP configurations designed to test and produce Yemen oil field. [Electric-Submersible Pump

    Energy Technology Data Exchange (ETDEWEB)

    Wilkie, D.I. (Canadian Occidental Petroleum Ltd., Calgary, Alberta (Canada))

    1993-09-27

    Innovative electric-submersible-pump (ESP) configurations were used in the exploration phase of a Yemen oil field discovered by Canadian Occidental Petroleum Ltd. Because of subnormal reservoir pressure, CanOxy developed the field with ESPs and had to install surface components that could operate at the high, 130 F., ambient temperatures common in Yemen. The field is in a remote area that has seen very little development. The reservoirs produce a medium-to-heavy crude with a low gas/oil ratio, typically less than 20 scf/bbl. Problems faced in evaluating the field included drilling through unconsolidated sands with high flow capacity and subnormal reservoir pressure. CanOxy had to develop the technology to test the wells during the exploration phase, and intends to use new, or at least uncommon technology, for producing the wells. The paper describes testing the wells, the electric generators and variable speed drives, and the use of these pumps on production wells.

  1. Self-gravitating field configurations: The role of the energy-momentum trace

    CERN Document Server

    Hod, Shahar

    2014-01-01

    Static spherically-symmetric matter distributions whose energy-momentum tensor is characterized by a non-negative trace are studied analytically within the framework of general relativity. We prove that such field configurations are necessarily highly relativistic objects. In particular, for matter fields with $T\\geq\\alpha\\cdot\\rho\\geq0$ (here $T$ and $\\rho$ are respectively the trace of the energy-momentum tensor and the energy density of the fields, and $\\alpha$ is a non-negative constant), we obtain the lower bound $\\text{max}_r\\{2m(r)/r\\}>(2+2\\alpha)/(3+2\\alpha)$ on the compactness (mass-to-radius ratio) of regular field configurations. In addition, we prove that these compact objects necessarily possess (at least) {\\it two} photon-spheres, one of which exhibits {\\it stable} trapping of null geodesics. The presence of stable photon-spheres in the corresponding curved spacetimes indicates that these compact objects may be nonlinearly unstable. We therefore conjecture that a negative trace of the energy-mom...

  2. Smart Cities as Organizational Fields: A Framework for Mapping Sustainability-Enabling Configurations

    Directory of Open Access Journals (Sweden)

    Paul Pierce

    2017-08-01

    Full Text Available Despite the impressive growth of smart city initiatives worldwide, an organizational theory of smart city has yet to be developed, and we lack models addressing the unprecedented organizational and management challenges that emerge in smart city contexts. Traditional models are often of little use, because smart cities pursue different goals than traditional organizations, are based on networked, cross-boundary activity systems, rely on distributed innovation processes, and imply adaptive policy-making. Complex combinations of factors may lead to vicious or virtuous cycles in smart city initiatives, but we know very little about how these factors may be identified and mapped. Based on an inductive study of a set of primary and secondary sources, we develop a framework for the configurational analysis of smart cities viewed as place-specific organizational fields. This framework identifies five key dimensions in the configurations of smart city fields; these five dimensions are mapped through five sub-frameworks, which can be used both separately as well as for an integrated analysis. Our contribution is conceived to support longitudinal studies, natural experiments and comparative analyses on smart city fields, and to improve our understanding of how different combinations of factors affect the capability of smart innovations to translate into city resilience, sustainability and quality of life. In addition, our results suggest that new forms of place-based entrepreneurship constitute the engine that allows for the dynamic collaboration between government, citizens and research centers in successful smart city organizational fields.

  3. Non-Linear Force-Free Field Modelling of Solar Coronal Jets in Theoretical Configurations

    Science.gov (United States)

    Savcheva, Antonia

    2017-08-01

    Coronal jets occur frequently on the Sun, and may contribute significantly to the solar wind. With the suite of instruments avilable now, e.g. on IRIS, Hinode and SDO, we can observe these phenomena in greater detail than ever before. Modeling and simulations can assist further in understanding the dynamic processes involved, but previous studies tend to consider only one mechanism (e.g. emergence or rotation) for the origin of the jet. In this study we model a series of idealised archetypaljet configurations and follow the evolution of the coronal magnetic field. This is a step towards understanding these idealised situations before considering their observational counterparts. Several simple situations are set up for the evolution of the photospheric magnetic field: a single parasitic polarity rotating or moving in a circular path; as well as opposite polarity pairs involved in flyby (shearing), cancellation or emergence; all in the presence of a uniform, open background magneticfield. The coronal magnetic field is evolved in time using a magnetofrictional relaxation method. While magnetofriction cannot accurately reproduce the dynamics of an eruptive phase, the structure of the coronal magnetic field, as well as the build up of electric currents and free magnetic energy are instructive. Certain configurations and motions produce a flux rope and allow the significant build up of free energy, reminiscent of the progenitors of so-called blowout jets, whereas other, simpler configurations are more comparable to the standard jet model. The next stage is a comparison with observed coronal jet structures and their corresponding photospheric evolution.

  4. Plasma-gun-assisted field-reversed configuration formation in a conical θ-pinch

    Science.gov (United States)

    Weber, T. E.; Intrator, T. P.; Smith, R. J.

    2015-04-01

    Injection of plasma via an annular array of coaxial plasma guns during the pre-ionization phase of field-reversed configuration (FRC) formation is shown to catalyze the bulk ionization of a neutral gas prefill in the presence of a strong axial magnetic field and change the character of outward flux flow during field-reversal from a convective process to a much slower resistive diffusion process. This approach has been found to significantly improve FRC formation in a conical θ-pinch, resulting in a ˜350% increase in trapped flux at typical operating conditions, an expansion of accessible formation parameter space to lower densities and higher temperatures, and a reduction or elimination of several deleterious effects associated with the pre-ionization phase.

  5. Plasma-gun-assisted field-reversed configuration formation in a conical θ-pinch

    Energy Technology Data Exchange (ETDEWEB)

    Weber, T. E., E-mail: tweber@lanl.gov; Intrator, T. P. [Los Alamos National Laboratory, Los Alamos, New Mexico 87545 (United States); Smith, R. J. [Department of Aeronautics and Astronautics, University of Washington, Seattle, Washington 98195 (United States)

    2015-04-15

    Injection of plasma via an annular array of coaxial plasma guns during the pre-ionization phase of field-reversed configuration (FRC) formation is shown to catalyze the bulk ionization of a neutral gas prefill in the presence of a strong axial magnetic field and change the character of outward flux flow during field-reversal from a convective process to a much slower resistive diffusion process. This approach has been found to significantly improve FRC formation in a conical θ-pinch, resulting in a ∼350% increase in trapped flux at typical operating conditions, an expansion of accessible formation parameter space to lower densities and higher temperatures, and a reduction or elimination of several deleterious effects associated with the pre-ionization phase.

  6. Space charge, plasma potential and electric field distributions in HiPIMS discharges of varying configuration

    Science.gov (United States)

    Liebig, B.; Bradley, J. W.

    2013-08-01

    An electron-emitting (emissive) probe has been used to study the temporal and spatial distribution of the plasma potential during high-power impulse magnetron sputtering (HiPIMS) discharges with various substrate and magnetic field configurations. The average power was 700 W, with a repetition frequency of 100 Hz and pulse duration of 100 µs. Strongly negative plasma potentials exceeding -300 V and electric fields up to 10 kV m-1, caused by strong separation of charges with net charge carrier densities Δn of about 1014 m-3, were observed during the ignition of the discharge. The spatial distribution of the plasma potential in the stable stage of the discharge showed values consistently 5 V more negative for a floating substrate compared with a grounded one, so enhancing electron transport around the insulated substrate to grounded walls. However, this change in the electrical configuration of the plasma does not alter significantly the fraction of ionized sputtered particles (of about 30%) that can potentially reach the substrate. By changing the degree of unbalance of the sputtering source, we find a strong correlation between the electric field strength in the magnetic trap (created through charge separation) and the absolute value (and shape) of the magnetic field. For the more unbalanced magnetron, a flattening of the plasma potential structure (decrease in the axial electric field) was observed close to the target. Our findings show in principle that manipulation of the potential barrier close to the target through changing the magnetic field can regulate the proportion of sputtered and ionized species reaching the substrate.

  7. Effect of Radial Density Configuration on Wave Field and Energy Flow in Axially Uniform Helicon Plasma

    Science.gov (United States)

    Chang, Lei; Li, Qingchong; Zhang, Huijie; Li, Yinghong; Wu, Yun; Zhang, Bailing; Zhuang, Zhong

    2016-08-01

    The effect of the radial density configuration in terms of width, edge gradient and volume gradient on the wave field and energy flow in an axially uniform helicon plasma is studied in detail. A three-parameter function is employed to describe the density, covering uniform, parabolic, linear and Gaussian profiles. It finds that the fraction of power deposition near the plasma edge increases with density width and edge gradient, and decays in exponential and “bump-on-tail” profiles, respectively, away from the surface. The existence of a positive second-order derivative in the volume density configuration promotes the power deposition near the plasma core, which to our best knowledge has not been pointed out before. The transverse structures of wave field and current density remain almost the same during the variation of density width and gradient, confirming the robustness of the m=1 mode observed previously. However, the structure of the electric wave field changes significantly from a uniform density configuration, for which the coupling between the Trivelpiece-Gould (TG) mode and the helicon mode is very strong, to non-uniform ones. The energy flow in the cross section of helicon plasma is presented for the first time, and behaves sensitive to the density width and edge gradient but insensitive to the volume gradient. Interestingly, the radial distribution of power deposition resembles the radial profile of the axial component of current density, suggesting the control of the power deposition profile in the experiment by particularly designing the antenna geometry to excite a required axial current distribution. supported by National Natural Science Foundation of China (No. 11405271)

  8. Transformer configuration in three dimensional Josephson lattices at zero magnetic field

    Energy Technology Data Exchange (ETDEWEB)

    Dominguez, D.; Gronbech-Jensen, N.; Bishop, A.R. [Theoretical Division, MS B262, Los Alamos National Laboratory, Los Alamos, New Mexico 87545 (United States); Shenoy, S.R. [International Center for Theoretical Physics, P.O. Box 586, Miramare, 34100 Trieste (Italy)

    1995-07-24

    Recent experiments on Bi{sub 2}Sr{sub 2}CaCu{sub 2}O{sub 8{minus}{ital y}} superconductors at zero magnetic field have been performed with a transformer configuration of contacts. We interpret the experimental data on the basis of large-scale Langevin dynamical simulations of a three dimensional (3D) Josephson lattice with a current bias through a single plane. We show that the experimentally observed effects can be attributed to linking thermal vortex loop excitations that cause voltages in neighboring superconducting planes to lock in a narrow temperature range near the 3D phase transition.

  9. Characteristics of geometric distortion correction with increasing field-of-view in open-configuration MRI.

    Science.gov (United States)

    Hong, Cheolpyo; Lee, Dong-Hoon; Han, Bong Soo

    2014-07-01

    Open-configuration magnetic resonance imaging (MRI) systems are becoming increasingly desirable for musculoskeletal imaging and image-guided radiotherapy because of their non-claustrophobic configuration. However, geometric image distortion in large fields-of-view (FOV) due to field inhomogeneity and gradient nonlinearity hinders the practical applications of open-type MRI. We demonstrated the use of geometric distortion correction for increasing FOV in open MRI. Geometric distortion was modeled and corrected as a global polynomial function. The appropriate polynomial order was identified as the minimum difference between the coordinates of control points in the distorted MR image space and those predicted by polynomial modeling. The sixth order polynomial function was found to give the optimal value for geometric distortion correction. The area of maximum distortion was<1 pixel with an FOV of 285mm. The correction performance error was increased at most 1.2% and 2.9% for FOVs of 340mm and~400mm compared with the FOV of 285mm. In particular, unresolved distortion was generated by local deformation near the gradient coil center. Copyright © 2014 Elsevier Inc. All rights reserved.

  10. Spectral properties of a ([I])-configuration atom driven by a pair of bichromatic fields

    Institute of Scientific and Technical Information of China (English)

    Jin Kang; Xie Xiao-Tao; Jiang Zhen-Yi

    2013-01-01

    The absorption spectrum and the incoherent fluorescence spectrum of the lower transition in an ([I])-configuration three-level atomic system driven by a pair of bichromatic fields is investigated.The transmission of the absorption profile from a multipeaked feature to a single-peak feature is identified.Adjusting the relative phase between the two driving fields,the splitting effects of the spectral peaks occur both in the fluorescence and the absorption spectra.Furthermore,phase modulating can dramatically lead to a great suppression of the amplitudes of the whole absorption spectrum.Physically,this effect is attributed to the phase-sensitive nature of the populations and coherence between the atomic states of the system.

  11. Optimization of the electrostatic and magnetic field configuration in the MITICA accelerator

    Energy Technology Data Exchange (ETDEWEB)

    Chitarin, G., E-mail: giuseppe.chitarin@igi.cnr.it [Consorzio RFX, Association EURATOM-ENEA, C.so Stati Uniti 4, 35127 Padova (Italy); Univ. di Padova, Department of Engineering and Management, strad. S. Nicola 3, 36100 Vicenza (Italy); Agostinetti, P. [Consorzio RFX, Association EURATOM-ENEA, C.so Stati Uniti 4, 35127 Padova (Italy); Esch, H.P.L. de [CEA-Cadarache, IRFM, F-13108 Saint-Paul-lez-Durance (France); Marcuzzi, D.; Marconato, N.; Sartori, E.; Serianni, G.; Sonato, P.; Veltri, P.; Zaccaria, P. [Consorzio RFX, Association EURATOM-ENEA, C.so Stati Uniti 4, 35127 Padova (Italy)

    2013-10-15

    MITICA (Megavolt ITER Injector Concept Advancement) is a test facility for the development of a full-size heating and current drive neutral beam injectors for the ITER Tokamak reactor. The optimized electrostatic and magnetic configuration has been defined by means of an iterative optimization involving all the physics and the engineering aspects. The acceleration grids have been designed considering optical performances and mechanical constraints related to embedded magnets, to cooling channels, to the grid stiffness and manufacturability. A combination of “local” vertical field and horizontal “long range” field has been found to be the most effective set-up for ion extraction, beam focusing and minimization and equalization of thermo-mechanical loads and minimal number of electrons exiting the accelerator.

  12. Equilibrium configurations of a jet of an ideally conducting liquid in an external nonuniform magnetic field

    Science.gov (United States)

    Zubarev, N. M.; Zubareva, O. V.

    2016-06-01

    Possible equilibrium configurations of the free surface of a jet of an ideally conducting liquid placed in a nonuniform magnetic field are considered. The magnetic field is generated by two thin wires that are parallel to the jet and bear oppositely directed currents. Equilibrium is due to a balance between capillary and magnetic forces. For the plane symmetric case, when the jet deforms only in the plane of its cross section, two one-parameter families of exact solutions to the problem are derived using the method of conformal mapping. According to these solutions, a jet with an initially circular cross section deforms up to splitting into two separate jets. A criterion for jet splitting is derived by analyzing approximate two-parameter solutions.

  13. Global simulations of magnetorotational turbulence III: influence of field configuration and mass injection

    CERN Document Server

    Parkin, E R

    2014-01-01

    The stresses produced by magnetorotational turbulence can provide effective angular momentum transport in accretion disks. However, questions remain about the ability of simulated disks to reproduce observationally inferred stress-to-gas-pressure ratios. In this paper we present a set of high resolution global magnetohydrodynamic disk simulations which are initialised with different field configurations: purely toroidal, vertical field lines, and nested poloidal loops. A mass source term is included which allows the total disk mass to equilibrate in simulations with long run times, and also enables the impact of rapid mass injection to be explored. Notably different levels of angular momentum transport are observed during the early-time transient disk evolution. However, given sufficient time to relax, the different models evolve to a statistically similar quasi-steady state with a stress-to-gas-pressure ratio, $\\alpha \\sim 0.032-0.036$. The indication from our results is that {\\it steady, isolated} disks may...

  14. Drift-kink instability induced by beam ions in field-reversed configurations

    Energy Technology Data Exchange (ETDEWEB)

    Nishimura, Kazumi; Horiuchi, Ritoku; Sato, Tetsuya [National Inst. for Fusion Science, Toki, Gifu (Japan)

    1999-04-01

    The drift-kink instability in field-reversed configurations with a beam component is investigated by means of a three-dimensional particle simulation. The unstable mode with the toroidal mode number n=4 grows with the rate {gamma} {approx} 0.1 - 1.0{omega}{sub ci} for a strong beam current and deforms the plasma profile along the beam orbit in the vicinity of the field-null line. This mode is nonlinearly saturated as a result of the relaxation of current profile. Both the saturation level and the growth rate tend to increase as the ratio of the beam current to the plasma current I{sub b}/I{sub p} increases. It is also found that there is a threshold value of the beam velocity {upsilon}{sub b} {approx} {upsilon}{sub Ti} (ion thermal velocity) for the excitation of the instability. (author)

  15. Flow Field of Circulating Fluidized Bed Reactor with Venturi Inlet Configuration

    Institute of Scientific and Technical Information of China (English)

    HU Jinbang; LI Yanping; CHEN Anxin

    2005-01-01

    Different two-equation k-ε models were used to simulate the gas flow field generated by a new type of circulating fluidized bed reactor with venturi gas distributor. The numerical results were compared with the experimental data. It has been shown that the simulation results from the standard k-ε model have the best match with the experimental data. Based on this model, the gas flow field in the venturi diffuser and riser was analyzed by the concept of velocity nonuniformity and dead zone percentage. Both the nonuniformity of gas velocity and the dead zone percentage reach the maximum at the venturi outlet due to the effect of the vortex. At the same time, it provides a good platform for the further optimization of the inlet configuration of circulating fluidized bed reactor.

  16. A first look into the magnetic field configuration of prominence threads using spectropolarimetric data

    CERN Document Server

    Suarez, D Orozco; Bueno, J Trujillo

    2013-01-01

    We show preliminary results of an ongoing investigation aimed at determining the configuration of the magnetic field vector in the threads of a quiescent hedgerow solar prominence using high-spatial resolution spectropolarimetric observations taken in the He I 1083.0 nm multiplet. The data consist of a two-dimensional map of a quiescent hedgerow prominence showing vertical threads. The observations were obtained with the Tenerife Infrared Polarimeter attached to the German Vacuum Tower Telescope at the Observatorio del Teide (Spain). The He I 1083.0 nm Stokes signals are interpreted with an inversion code, which takes into account the key physical processes that generate and/or modify circular and linear polarization signals in the He I 1083.0 nm triplet: the Zeeman effect, anisotropic radiation pumping, and the Hanle effect. We present initial results of the inversions, i.e, the strength and orientation of the magnetic field vector along the prominence and in prominence threads.

  17. Full-field wafer warpage measurement technique

    Science.gov (United States)

    Hsieh, H. L.; Lee, J. Y.; Huang, Y. G.; Liang, A. J.; Sun, B. Y.

    2017-06-01

    An innovative moiré technique for full-field wafer warpage measurement is proposed in this study. The wafer warpage measurement technique is developed based on moiré method, Talbot effect, scanning profiling method, stroboscopic, instantaneous phase-shift method, as well as four-step phase shift method, high resolution, high stability and full-field measurement capabilities can be easily achieved. According to the proposed full-field optical configuration, a laser beam is expanded into a collimated beam with a 2-inch diameter and projected onto the wafer surface. The beam is reflected by the wafer surface and forms a moiré fringe image after passing two circular gratings, which is then focused and captured on a CCD camera for computation. The corresponding moiré fringes reflected from the wafer surface are obtained by overlapping the images of the measuring grating and the reference grating. The moiré fringes will shift when wafer warpage occurs. The phase of the moiré fringes will change proportionally to the degree of warpage in the wafer, which can be measured by detecting variations in the phase shift of the moiré fringes in each detection points on the surface of the entire wafer. The phase shift variations of each detection points can be calculated via the instantaneous phase-shift method and the four-step phase-shift method. By adding up the phase shift variations of each detection points along the radii of the circular gratings, the warpage value and surface topography of the wafer can be obtained. Experiments show that the proposed method is capable of obtaining test results similar to that of a commercial sensor, as well as performing accurate measurements under high speed rotation of 1500rpm. As compared to current warpage measurement methods such as the beam optical method, confocal microscopy, laser interferometry, shadow moiré method, and structured light method, this proposed technique has the advantage of full-field measurement, high

  18. Self-dual configurations in Abelian Higgs models with k-generalized gauge field dynamics

    Science.gov (United States)

    Casana, R.; Cavalcante, A.; da Hora, E.

    2016-12-01

    We have shown the existence of self-dual solutions in new Maxwell-Higgs scenarios where the gauge field possesses a k-generalized dynamic, i.e., the kinetic term of gauge field is a highly nonlinear function of F μν F μν . We have implemented our proposal by means of a k-generalized model displaying the spontaneous symmetry breaking phenomenon. We implement consistently the Bogomol'nyi-Prasad-Sommerfield formalism providing highly nonlinear self-dual equations whose solutions are electrically neutral possessing total energy proportional to the magnetic flux. Among the infinite set of possible configurations, we have found families of k-generalized models whose self-dual equations have a form mathematically similar to the ones arising in the Maxwell-Higgs or Chern-Simons-Higgs models. Furthermore, we have verified that our proposal also supports infinite twinlike models with | ϕ|4-potential or | ϕ|6-potential. With the aim to show explicitly that the BPS equations are able to provide well-behaved configurations, we have considered a test model in order to study axially symmetric vortices. By depending of the self-dual potential, we have shown that the k-generalized model is able to produce solutions that for long distances have a exponential decay (as Abrikosov-Nielsen-Olesen vortices) or have a power-law decay (characterizing delocalized vortices). In all cases, we observe that the generalization modifies the vortex core size, the magnetic field amplitude and the bosonic masses but the total energy remains proportional to the quantized magnetic flux.

  19. Self-dual configurations in Abelian Higgs models with k-generalized gauge field dynamics

    Energy Technology Data Exchange (ETDEWEB)

    Casana, R.; Cavalcante, A. [Departamento de Física, Universidade Federal do Maranhão,65080-805, São Luís, Maranhão (Brazil); Hora, E. da [Departamento de Física, Universidade Federal do Maranhão,65080-805, São Luís, Maranhão (Brazil); Coordenadoria Interdisciplinar de Ciência e Tecnologia, Universidade Federal do Maranhão,65080-805, São Luís, Maranhão (Brazil)

    2016-12-14

    We have shown the existence of self-dual solutions in new Maxwell-Higgs scenarios where the gauge field possesses a k-generalized dynamic, i.e., the kinetic term of gauge field is a highly nonlinear function of F{sub μν}F{sup μν}. We have implemented our proposal by means of a k-generalized model displaying the spontaneous symmetry breaking phenomenon. We implement consistently the Bogomol’nyi-Prasad-Sommerfield formalism providing highly nonlinear self-dual equations whose solutions are electrically neutral possessing total energy proportional to the magnetic flux. Among the infinite set of possible configurations, we have found families of k-generalized models whose self-dual equations have a form mathematically similar to the ones arising in the Maxwell-Higgs or Chern-Simons-Higgs models. Furthermore, we have verified that our proposal also supports infinite twinlike models with |ϕ|{sup 4}-potential or |ϕ|{sup 6}-potential. With the aim to show explicitly that the BPS equations are able to provide well-behaved configurations, we have considered a test model in order to study axially symmetric vortices. By depending of the self-dual potential, we have shown that the k-generalized model is able to produce solutions that for long distances have a exponential decay (as Abrikosov-Nielsen-Olesen vortices) or have a power-law decay (characterizing delocalized vortices). In all cases, we observe that the generalization modifies the vortex core size, the magnetic field amplitude and the bosonic masses but the total energy remains proportional to the quantized magnetic flux.

  20. Rethermalization of a field-reversed configuration plasma in translation experiments

    Science.gov (United States)

    Himura, Haruhiko; Okada, Shigefumi; Sugimoto, Satoshi; Goto, Seiichi

    1995-01-01

    A translation experiment of field-reversed configuration (FRC) plasma is performed on the FIX machine [Shiokawa and Goto, Phys. Fluids B 5, 534 (1993)]. The translated FRC bounces between magnetic mirror fields at both ends of a confinement region. The plasma loses some of its axial kinetic energy when it is reflected by the magnetic mirror field, and eventually settles down in the confinement region. In this reflection process, the plasma temperature rises significantly. Such plasma rethermalization has been observed in OCT-L1 experiments [Ito et al., Phys. Fluids 30, 168 (1987)], but rarely in FRX-C/T experiments [Rej et al., Phys. Fluids 29, 852 (1986)]. It is found that the rethermalization depends on the relation between the plasma temperature and the translation velocity. The rethermalization occurs only in the case where the translation velocity exceeds the sound velocity. This result implies the rethermalization is caused by a shock wave induced within the FRC when the plasma is reflected by the magnetic mirror field.

  1. Hall effect on a Merging Formation Process of a Field-Reversed Configuration

    Science.gov (United States)

    Kaminou, Yasuhiro; Guo, Xuehan; Inomoto, Michiaki; Ono, Yasushi; Horiuchi, Ritoku

    2015-11-01

    Counter-helicity spheromak merging is one of the formation methods of a Field-Reversed Configuration (FRC). In counter-helicity spheromak merging, two spheromaks with opposing toroidal fields merge together, through magnetic reconnection events and relax into a FRC, which has no or little toroidal field. This process contains magnetic reconnection and a relaxation phenomena, and the Hall effect has some essential effects on these process because the X-point in the magnetic reconnection or the O-point of the FRC has no or little magnetic field. However, the Hall effect as both global and local effect on counter-helicity spheromak merging has not been elucidated. In this poster, we conducted 2D/3D Hall-MHD simulations and experiments of counter-helicity spheromak merging. We find that the Hall effect enhances the reconnection rate, and reduces the generation of toroidal sheared-flow. The suppression of the ``slingshot effect'' affects the relaxation process. We will discuss details in the poster.

  2. Application of measurement configuration optimization for accurate metrology of sub-wavelength dimensions in multilayer gratings using optical scatterometry.

    Science.gov (United States)

    Zhu, Jinlong; Shi, Yating; Goddard, Lynford L; Liu, Shiyuan

    2016-09-01

    Critical dimension measurement accuracy in optical scatterometry relies not only on the systematic noise level of instruments and the reliability of forward modeling algorithms, but also heavily on the measurement configuration. To construct a set of potentially high-accuracy configurations, we apply a general measurement configuration optimization method based on error propagation theory and singular value decomposition, by which the measurement accuracy is approximated as a function of a pseudo Jacobian with respect to the measurement configurations. Simulations and experiments for the optical metrology of a sub-wavelength deep-etched multilayer grating establish the feasibility of the proposed method.

  3. Overview of C-2 field-reversed configuration experiment plasma diagnostics

    Energy Technology Data Exchange (ETDEWEB)

    Gota, H., E-mail: hgota@trialphaenergy.com; Thompson, M. C.; Tuszewski, M.; Binderbauer, M. W. [Tri Alpha Energy, Inc., Rancho Santa Margarita, California 92688 (United States)

    2014-11-15

    A comprehensive diagnostic suite for field-reversed configuration (FRC) plasmas has been developed and installed on the C-2 device at Tri Alpha Energy to investigate the dynamics of FRC formation as well as to understand key FRC physics properties, e.g., confinement and stability, throughout a discharge. C-2 is a unique, large compact-toroid merging device that produces FRC plasmas partially sustained for up to ∼5 ms by neutral-beam (NB) injection and end-on plasma-guns for stability control. Fundamental C-2 FRC properties are diagnosed by magnetics, interferometry, Thomson scattering, spectroscopy, bolometry, reflectometry, and NB-related fast-ion/neutral diagnostics. These diagnostics (totaling >50 systems) are essential to support the primary goal of developing a deep understanding of NB-driven FRCs.

  4. Improvement of the magnetic configuration in the reversed field pinch through successive bifurcationsa)

    Science.gov (United States)

    Lorenzini, R.; Agostini, M.; Alfier, A.; Antoni, V.; Apolloni, L.; Auriemma, F.; Barana, O.; Baruzzo, M.; Bettini, P.; Bonfiglio, D.; Bolzonella, T.; Bonomo, F.; Brombin, M.; Buffa, A.; Canton, A.; Cappello, S.; Carraro, L.; Cavazzana, R.; Chitarin, G.; Dal Bello, S.; De Lorenzi, A.; De Masi, G.; Escande, D. F.; Fassina, A.; Franz, P.; Gaio, E.; Gazza, E.; Giudicotti, L.; Gnesotto, F.; Gobbin, M.; Grando, L.; Guo, S. C.; Innocente, P.; Luchetta, A.; Manduchi, G.; Marchiori, G.; Marcuzzi, D.; Marrelli, L.; Martin, P.; Martini, S.; Martines, E.; Milani, F.; Moresco, M.; Novello, L.; Ortolani, S.; Paccagnella, R.; Pasqualotto, R.; Peruzzo, S.; Piovan, R.; Piovesan, P.; Piron, L.; Pizzimenti, A.; Pomaro, N.; Predebon, I.; Puiatti, M. E.; Rostagni, G.; Sattin, F.; Scarin, P.; Serianni, G.; Sonato, P.; Spada, E.; Soppelsa, A.; Spagnolo, S.; Spizzo, G.; Spolaore, M.; Taliercio, C.; Terranova, D.; Toigo, V.; Valisa, M.; Veltri, P.; Vianello, N.; Zaccaria, P.; Zaniol, B.; Zanotto, L.; Zilli, E.; Zuin, M.

    2009-05-01

    The reversed field pinch (RFP) is a magnetic configuration alternative to the tokamak that can be considered for a second generation of reactors. In this paper new remarkable results obtained in the RFP experiment RFX-mod are presented, showing that an internal transport barrier delimitates a large fraction of the plasma volume in a RFP when the current is raised to ˜1.5 MA. The formation of this transport barrier is related to a profound, spontaneous modification of the magnetic topology. Due to the occurrence of a saddle node bifurcation the plasma enters in the single helical axis state, which is theoretically known to be more resilient to chaos. This bifurcation is driven by the amplitude of the helical perturbation which dominates the mode spectrum.

  5. Field-Reversed Configuration Power Plant Critical-Issue Scoping Study

    Energy Technology Data Exchange (ETDEWEB)

    Santarius, J. F.; Mogahed, E. A.; Emmert, G. A.; Khater, H. Y.; Nguyen, C. N.; Ryzhkov, S. V.; Stubna, M. D.

    2000-03-31

    A team from the Universities of Wisconsin, Washington, and Illinois performed an engineering scoping study of critical issues for field-reversed configuration (FRC) power plants. The key tasks for this research were (1) systems analysis for deuterium-tritium (D-T) FRC fusion power plants, and (2) conceptual design of the blanket and shield module for an FRC fusion core. For the engineering conceptual design of the fusion core, the project team focused on intermediate-term technology. For example, one decision was to use steele structure. The FRC systems analysis led to a fusion power plant with attractive features including modest size, cylindrical symmetry, good thermal efficiency (52%), relatively easy maintenance, and a high ratio of electric power to fusion core mass, indicating that it would have favorable economics.

  6. Self-ignition of an advanced fuel field-reversed configuration reactor by fusion product heating

    Energy Technology Data Exchange (ETDEWEB)

    Ohnishi, M.; Ohi, S.; Okamoto, M.; Momota, H.; Wakabayashi, J.

    1987-09-01

    A self-ignition of a deuterium-deuterium (D-D)-/sup 3/He fuel field-reversed configuration (FRC) plasma by fusion product heating is studied by using the point plasma model, where an FRC plasma equilibrium is taken into account. It is numerically demonstrated that the D-D-/sup 3/He plasma can be evolved from a deuterium-tritium burning plasma in a controlled manner by means of a compression-decompression control as well as a fueling control. It is also indicated that the increase of a trapped flux is effective for suppressing the excessive elongation of a plasma during the transition. The proposed method may provide a solution to the problem on plasma heating to attain a D-D-/sup 3/He self-ignition.

  7. Field-Reversed Configuration Formation Scheme Utilizing a Spheromak and Solenoid Induction

    Energy Technology Data Exchange (ETDEWEB)

    Gerhardt, S. P.; Belova, E. V.; Yamada, M.; Ji, H.; Ren, B.; McGeehan, B.; Inomoto, M.

    2008-06-12

    A new field-reversed configuration (FRC) formation technique is described, where a spheromak transitions to a FRC with inductive current drive. The transition is accomplished only in argon and krypton plasmas, where low-n kink modes are suppressed; spheromaks with a lighter majority species, such as neon and helium, either display a terminal tilt-mode, or an n=2 kink instability, both resulting in discharge termination. The stability of argon and krypton plasmas through the transition is attributed to the rapid magnetic diffusion of the currents that drive the kink-instability. The decay of helicity during the transition is consistent with that expected from resistivity. This observation indicates a new scheme to form a FRC plasma, provided stability to low-n modes is maintained, as well as a unique situation where the FRC is a preferred state.

  8. Overview of C-2 field-reversed configuration experiment plasma diagnostics.

    Science.gov (United States)

    Gota, H; Thompson, M C; Tuszewski, M; Binderbauer, M W

    2014-11-01

    A comprehensive diagnostic suite for field-reversed configuration (FRC) plasmas has been developed and installed on the C-2 device at Tri Alpha Energy to investigate the dynamics of FRC formation as well as to understand key FRC physics properties, e.g., confinement and stability, throughout a discharge. C-2 is a unique, large compact-toroid merging device that produces FRC plasmas partially sustained for up to ∼5 ms by neutral-beam (NB) injection and end-on plasma-guns for stability control. Fundamental C-2 FRC properties are diagnosed by magnetics, interferometry, Thomson scattering, spectroscopy, bolometry, reflectometry, and NB-related fast-ion/neutral diagnostics. These diagnostics (totaling >50 systems) are essential to support the primary goal of developing a deep understanding of NB-driven FRCs.

  9. Advanced Biasing Experiments on the C-2 Field-Reversed Configuration Device

    Science.gov (United States)

    Thompson, Matthew; Korepanov, Sergey; Garate, Eusebio; Yang, Xiaokang; Gota, Hiroshi; Douglass, Jon; Allfrey, Ian; Valentine, Travis; Uchizono, Nolan; TAE Team

    2014-10-01

    The C-2 experiment seeks to study the evolution, heating and sustainment effects of neutral beam injection on field-reversed configuration (FRC) plasmas. Recently, substantial improvements in plasma performance were achieved through the application of edge biasing with coaxial plasma guns located in the divertors. Edge biasing provides rotation control that reduces instabilities and E × B shear that improves confinement. Typically, the plasma gun arcs are run at ~ 10 MW for the entire shot duration (~ 5 ms), which will become unsustainable as the plasma duration increases. We have conducted several advanced biasing experiments with reduced-average-power plasma gun operating modes and alternative biasing cathodes in an effort to develop an effective biasing scenario applicable to steady state FRC plasmas. Early results show that several techniques can potentially provide effective, long-duration edge biasing.

  10. Local electric field and configuration of CO molecules adsorbed on a nanostructured surface with nanocones

    Institute of Scientific and Technical Information of China (English)

    You Rong-Yi; Huang Xiao-Jing

    2009-01-01

    Based on the nanostructured surface model that the (platinum,Pt) nanocones grow out symmetrically from a plane substrate,the local electric field near the conical nanoparticle surface is computed and discussed. On the basis of these results,the adsorbed CO molecules are modelled as dipoles,and three kinds of interactions,I.e. Interactions between dipoles and local electric field,between dipoles and dipoles,as well as between dipoles and nanostructured substrate,are taken into account. The spatial configuration of CO molecules adsorbed on the nanocone surface is then given by Monte-Carlo simulation. Our results show that the CO molecules adsorbed on the nanocone surface cause local agglomeration under the action of an external electric field,and this agglomeration becomes more compact with decreasing conical angle,which results in a stronger interaction among molecules. These results serve as a basis for explaining abnormal phenomena such as the abnormal infrared effect (AIRE),which was found when CO molecules were adsorbed on the nancetructured transition-metal surface.

  11. The behaviour of magnetic field lines and drifts in 3D configurations

    Energy Technology Data Exchange (ETDEWEB)

    Fischer, O. [Ecole Polytechnique Federale de Lausanne, Centre de Recherches en Physique des Plasmas (CRPP), CH-1015 Lausanne (Switzerland)

    2001-04-01

    The magnetic topology and the particles drift orbits in 3D configurations are analyzed with numerical tools developed during this thesis (the MFLT3D code and the VENUS code) or with existing codes (the VMEC code and the TERPSICHORE code). We will focus our study on the effect of a magnetic perturbation in a MHD equilibrium and on the neoclassical transport in new 3D reactor designs. Firstly, the magnetic structure and particle drift orbits are studied in a monotonic q-profile and in a reversed shear TEXTOR equilibrium that is subject to a magnetic perturbation driven by the Dynamic Ergodic Divertor (DED). The main results prove that there exists a transport barrier for the magnetic field lines and for circulating particles in the reversed shear case when the DED is applied. This transport barrier occurs near the surface of minimum q-value where the KAM theory may be invalid. Moreover, we have remarked that trapped particles are lost due to the presence of the ripple and the DED does not affect their trajectories. Then, we have observed that a magnetic perturbation produced by saddle coils, for example, can control internal instabilities like tearing modes in the JET tokamak. We have shown that depending on the n mode number, the saddle coils have beneficial effects on the island width of internal instabilities. Finally, the study of neoclassical transport and Q-particles confinement are analyzed in 3D reactor designs like the QAS3, the ST/sphellamak hybrid and the sphellamak. We have observed that neither the QAS3 nor the ST/sphellamak are quasiaxisymmetric configurations. Thus the transport process is governed by the helical deformation of the magnetic field strength and these configurations do not confine the trapped Q-particles. On the other hand, the sphellamak is a nearly isodynamic structure in the plasma core which leads to good Q-particle confinement and the neoclassical transport is very similar to that obtained in a 2D equivalent tokamak. (author)

  12. The configuration of plantar pressure sensing cells for wearable measurement of COP coordinates.

    Science.gov (United States)

    Wang, Dian; Cai, Ping; Mao, Zhiyong

    2016-10-26

    Wearable measurement of center of pressure (COP) coordinates is the key of obtaining the measurement of natural gait. Plantar pressure insole is the right sensing unit for plantar pressure monitoring for long-term outdoor measurements and the control of walking assisting exoskeleton robot. It's necessary to study the configuration of pressure sensing cells. This study explored the sensing cell configuration for the plantar pressure insole. The data of plantar pressure of walking is collected for layout variants. The RMSE of COP coordinates estimations are used as the evaluation criteria. The RMSE of COP coordinates decreases from 8.00 to 3.20 mm as the amount of pressure sensing cells increases from 2 to 7. The size of pressure sensing cells contribute to reduce the RMSE of COP coordinates and 7 pressure sensing cells, with the size of 2.0-2.5 cm have the satisfying performance. Adding pressure sensing cell in the heel and hallux area increase the accuracy of estimating COP coordinates. Comparison results indicate that the configuration of 7 pressure sensing cells has a satisfying measurement performance.

  13. Development of electric currents in a magnetic field configuration containing a magnetic null point

    Science.gov (United States)

    Santos, J. C.; Büchner, J.; Otto, A.

    2011-01-01

    Context. In the past the role of magnetic null points in the generation of electric currents was investigated mainly in the close vicinity of the null, with perturbations being applied at nearby boundaries, or for a magnetic null configuration with a dome-shaped fan. In the solar atmosphere, however, electric currents are generated by perturbations originating at the photosphere, far away from coronal 3D nulls, and the occurence of magnetic nulls with a dome-shaped fan is apparently not common. Aims: We investigate the consequences of photospheric motion for the development of electric currents in a coronal magnetic field configuration containing a null, located far away from the boundaries, and the influence of topological structures on the spatial distribution of the currents. Methods: We use a 3D resistive MHD code to investigate the consequences of photospheric plasma motion for the generation of currents in a coronal magnetic field containing a null. The plasma is considered fully compressible and is initially in hydrostatic equilibrium. The initial magnetic field is potential (current free). Results: The photospheric plasma motion causes magnetic field perturbations that propagate to the corona along the field lines at the local Alfvén speed. The Alfvénic wave perturbations correspond to a propagating current directed mainly parallel to the magnetic field. Perpendicular currents connect to return currents to close the current system. The magnetic perturbations eventually reach the vicinity of the null. However, the currents forming in and around the null, near the fan surface or near the spine field lines, are not always the strongest currents developing in the simulation box. In our simulation, the strongest currents develop close to the bottom boundary, where the plasma is moved, and below the null point, in a region where field line connectivity considerably changes. Conclusions: Our simulation shows that the presence of a magnetic null point does not

  14. Backside configured surface plasmonic enhancement

    Energy Technology Data Exchange (ETDEWEB)

    Gu, Guiru; Lu, Xuejun, E-mail: xuejun-lu@uml.edu [Department of Electrical and Computer Engineering, University of Massachusetts Lowell, One University Avenue, Lowell, MA 01854 (United States); Vaillancourt, Jarrod [Applied NanoFemto Technologies, LLC, 181 Stedman St. 2, Lowell, MA 01851 (United States)

    2014-03-31

    In this work, we fabricated, measured and compared the quantum dots infrared photodetector enhancement by the top- and backside- configured plasmonic structures. The backside configured plasmonic structure can provide much higher device performance enhancement. Furthermore, the excitation of the surface plasmonic waves by the top- and backside- configured plasmonic structures was analyzed. Detailed simulation results of the electric field at different wavelength from top illumination and backside illumination were provided. The stronger electric field from the backside illumination attributed to the higher enhancement.

  15. Diagnostic suite of the C-2U advanced beam-driven field-reversed configuration plasma experiment

    Science.gov (United States)

    Thompson, M. C.; Gota, H.; Putvinski, S.; Tuszewski, M.; Binderbauer, M.

    2016-11-01

    The C-2U experiment at Tri Alpha Energy studies the evolution of field-reversed configuration (FRC) plasmas sustained by neutral beam injection. Data on the FRC plasma performance are provided by a comprehensive suite of diagnostics that includes magnetic sensors, interferometry, Thomson scattering, spectroscopy, bolometry, reflectometry, neutral particle analyzers, and fusion product detectors. While many of these diagnostic systems were inherited from the preceding experiment C-2, C-2U has a variety of new and upgraded diagnostic systems: multi-chord far-infrared polarimetry, multiple fast imaging cameras with selectable atomic line filters, proton detector arrays, and 100 channel bolometer units capable of observing multiple regions of the spectrum simultaneously. In addition, extensive ongoing work focuses on advanced methods of measuring separatrix shape and plasma current profile that will facilitate equilibrium reconstruction and active control of the FRC plasma.

  16. Diagnostic suite of the C-2U advanced beam-driven field-reversed configuration plasma experiment

    Energy Technology Data Exchange (ETDEWEB)

    Thompson, M. C., E-mail: mthompson@trialphaenergy.com; Gota, H.; Putvinski, S.; Tuszewski, M.; Binderbauer, M. [Tri Alpha Energy, Inc., Rancho Santa Margarita, California 92688 (United States)

    2016-11-15

    The C-2U experiment at Tri Alpha Energy studies the evolution of field-reversed configuration (FRC) plasmas sustained by neutral beam injection. Data on the FRC plasma performance are provided by a comprehensive suite of diagnostics that includes magnetic sensors, interferometry, Thomson scattering, spectroscopy, bolometry, reflectometry, neutral particle analyzers, and fusion product detectors. While many of these diagnostic systems were inherited from the preceding experiment C-2, C-2U has a variety of new and upgraded diagnostic systems: multi-chord far-infrared polarimetry, multiple fast imaging cameras with selectable atomic line filters, proton detector arrays, and 100 channel bolometer units capable of observing multiple regions of the spectrum simultaneously. In addition, extensive ongoing work focuses on advanced methods of measuring separatrix shape and plasma current profile that will facilitate equilibrium reconstruction and active control of the FRC plasma.

  17. Characterizing configurable transmission modes in plasma photonic crystals using scanning field mapping

    Science.gov (United States)

    Wang, Benjamin; Cappelli, Mark

    2016-10-01

    A fully tunable plasma photonic crystal is used to control the propagation of free space electromagnetic waves in the S to X band of the microwave spectrum. A structured array of discharge plasma tubes are arranged in a square crystal lattice with the individual plasma dielectric constant tuned through variation in the plasma density. Microwave field-mapping is used to characterize the transmitted electromagnetic fields of the tunable device operating in waveguiding and bending modes. These modes are obtained by introducing appropriate line defects in the photonic crystal structure by controlling the activity of individual plasma tubes. Comparisons are made of the measured fields to those simulated using commercially-available software.

  18. The measurement of the modal strain fields using digital shearography

    Science.gov (United States)

    Lopes, H.; Ribeiro, J. E.; Vaz, M.; Gomes, J. M.

    2010-06-01

    This work presents a Michelson shearography interferometer configuration associated with stroboscopic double illumination technique for the measurement of modal rotation fields and their strain fields on a clamped circular aluminium plate. The speckle pattern is frozen by the synchronization between the LASER illumination and the modal vibration of the object. The quantitative evaluation is performed for each digital shearogram using a time modulation technique. The setup of double illumination LASER with out-of-plane opposite sensitivity allows the two phase maps measurement of the modal spatial gradient. The modal rotation and strain fields are extracted by the combination of this two digital phase maps. Image processing techniques are applied on the phase maps to obtain full-field measurements using a dedicated post-processing algorithm. Finally, is presented a comparison between the experimental measurement and the numerical solution.

  19. The measurement of the modal strain fields using digital shearography

    Directory of Open Access Journals (Sweden)

    Gomes J.M.

    2010-06-01

    Full Text Available This work presents a Michelson shearography interferometer configuration associated with stroboscopic double illumination technique for the measurement of modal rotation fields and their strain fields on a clamped circular aluminium plate. The speckle pattern is frozen by the synchronization between the LASER illumination and the modal vibration of the object. The quantitative evaluation is performed for each digital shearogram using a time modulation technique. The setup of double illumination LASER with out-of-plane opposite sensitivity allows the two phase maps measurement of the modal spatial gradient. The modal rotation and strain fields are extracted by the combination of this two digital phase maps. Image processing techniques are applied on the phase maps to obtain full-field measurements using a dedicated post-processing algorithm. Finally, is presented a comparison between the experimental measurement and the numerical solution.

  20. System for controllable magnetic measurement with direct field determination

    Science.gov (United States)

    Stupakov, O.

    2012-02-01

    This work describes a specially designed setup for magnetic hysteresis and Barkhausen noise measurements. The setup combines two main elements: an improved fast algorithm to control the waveform of magnetic induction and simultaneous direct determination of the magnetic field. The digital feedback algorithm uses only the previous measurement cycle to correct the magnetization voltage without any additional correlation parameter; it usually converges after several tens of cycles. The magnetic field is measured at the sample surface using a vertically mounted array of sensitive Hall sensors. Linear extrapolation of the tangential field profile to the sample surface determines the true waveform of the magnetic field. This unique combination of physically based control for both parameters of the magnetization process provides stable and reliable results, which are independent of a specified experimental configuration. This is illustrated for the industrially attractive measurements of non-oriented electrical steels with a 50 Hz sinusoidal induction waveform.

  1. Impacts of field of view configuration of Cross-track Infrared Sounder on clear-sky observations.

    Science.gov (United States)

    Wang, Likun; Chen, Yong; Han, Yong

    2016-09-01

    Hyperspectral infrared radiance measurements from satellite sensors contain valuable information on atmospheric temperature and humidity profiles and greenhouse gases, and therefore are directly assimilated into numerical weather prediction (NWP) models as inputs for weather forecasting. However, data assimilations in current operational NWP models still mainly rely on cloud-free observations due to the challenge of simulating cloud-contaminated radiances when using hyperspectral radiances. The limited spatial coverage of the 3×3 field of views (FOVs) in one field of regard (FOR) (i.e., spatial gap among FOVs) as well as relatively large footprint size (14 km) in current Cross-track Infrared Sounder (CrIS) instruments limits the amount of clear-sky observations. This study explores the potential impacts of future CrIS FOV configuration (including FOV size and spatial coverage) on the amount of clear-sky observations by simulation experiments. The radiance measurements and cloud mask products (VCM) from the Visible Infrared Imager Radiometer Suite (VIIRS) are used to simulate CrIS clear-sky observation under different FOV configurations. The results indicate that, given the same FOV coverage (e.g., 3×3), the percentage of clear-sky FOVs and the percentage of clear-sky FORs (that contain at least one clear-sky FOV) both increase as the FOV size decreases. In particular, if the CrIS FOV size were reduced from 14 km to 7 km, the percentage of clear-sky FOVs increases from 9.02% to 13.51% and the percentage of clear-sky FORs increases from 18.24% to 27.51%. Given the same FOV size but with increasing FOV coverage in each FOR, the clear-sky FOV observations increases proportionally with the increasing sampling FOVs. Both reducing FOV size and increasing FOV coverage can result in more clear-sky FORs, which benefit data utilization of NWP data assimilation.

  2. Neutral Beam Injection System for the C-2W Field Reversed Configuration Experiment

    Science.gov (United States)

    Dunaevsky, Alexander; Ivanov, Alexander; Kolmogorov, Vyacheslav; Smirnov, Artem; Korepanov, Sergey; Binderbauer, Michl; TAE Team; BINP Team

    2016-10-01

    C-2U Field-Reversed Configuration (FRC) experiment proved substantial reduction in turbulence-driven losses via tangential neutral beam injection (NBI) coupled with electrically biased plasma guns at the plasma ends. Under such conditions, highly reproducible, advanced beam-driven FRCs were produced and sustained for times significantly longer (more than 5 ms) than all characteristic plasma decay times without beams. To further improve FRC sustainment and demonstrate the FRC ramp-up, the C-2U experimental device is undergoing a major upgrade. The upgrade, C-2W, will have a new NBI system producing a record total hydrogen beam power of 20 + MW in a 30ms pulse. The NBI system consists of eight positive-ion based injectors featuring flexible, modular design. Four out of eight NBI injectors have a capability to switch the beam energy during a shot from the initial 15 keV to 40 keV at a constant beam current. This feature allows to increase the beam energy and thereby optimize the beam-plasma coupling during the magnetic field ramp up. This presentation provides an overview of the C-2W NBI system, including the design of the switchable energy injectors, layout of the power supply system, and results of the prototype testing.

  3. Confining a closed configuration of a liquid with an electromagnetic field

    Energy Technology Data Exchange (ETDEWEB)

    Getselev, Z.N.; Martynov, G.I.

    1979-01-01

    The authors consider an arrangement for electromagnetic ingot shaping. A liquid metal mass is contained by electromagnetic forces excited in its surface layer, where the field intensity is adjusted by a shield. The mass forces which maintain the configuration of the ingot during cooling are broken down into potential and vortex forces. Surface tension forces are not considered in the analysis since the meniscus surface curvature is small and the energy of the mass forces exceeds that of the surface forces by several times. An analytical procedure for computing the potential and vortex fields of force is developed for two special cases of the liquid phase surface shape. Formulas are derived for the acting electromagnetic force, the potential of the mass forces, the vortex mass force and the maximum mechanical energy of the vortex forces at any point in the liquid phase, where the liquid phase is limited to the following cases: (a) a rectangular meniscus; (b) a meniscus of constant slope; (c) a hardened flat wall, at the surface of which the electromagnetic force is constant. The distribution and relationship of the mass potential and vortex forces acting in the melt are shown graphically.

  4. Fusion Ash Separation in the Princeton Field-Reversed Configuration Reactor

    Science.gov (United States)

    Abbate, Joseph; Yeh, Meagan; McGreivy, Nick; Cohen, Samuel

    2016-10-01

    The Princeton Field-Reversed Configuration (PFRC) concept relies on low-neutron production by D-3He fusion to enable small, safe nuclear-fusion reactors to be built, an approach requiring rapid and efficient extraction of fusion ash and energy produced by D-3He fusion reactions. The ash exhaust stream would contain energetic (0.1-1 MeV) protons, T, 3He, and 4He ions and nearly 1e5 cooler (ca. 100 eV) D ions. The T extracted from the reactor would be a valuable fusion product in that it decays into 3He, which could be used as fuel. If the T were not extracted it would be troublesome because of neutron production by the D-T reaction. This paper discusses methods to separate the various species in a PFRC reactor's exhaust stream. First, we discuss the use of curved magnetic fields to separate the energetic from the cool components. Then we discuss exploiting material properties, specifically reflection, sputtering threshold, and permeability, to allow separation of the hydrogen from the helium isotopes. DOE Contract Number DE-AC02-09CH11466.

  5. Enhanced magnetic field probe array for improved excluded flux calculations on the C-2U advanced beam-driven field-reversed configuration plasma experiment

    Energy Technology Data Exchange (ETDEWEB)

    Roche, T., E-mail: troche@trialphaenergy.com; Thompson, M. C.; Mendoza, R.; Allfrey, I.; Garate, E.; Romero, J.; Douglass, J. [Tri Alpha Energy, P.O. Box 7010, Rancho Santa Margarita, California 92688 (United States)

    2016-11-15

    External flux conserving coils were installed onto the exterior of the C-2U [M. W. Binderbauer et al., Phys. Plasmas 22, 056110 (2015)] confinement vessel to increase the flux confinement time of the system. The 0.5 in. stainless steel vessel wall has a skin time of ∼5 ms. The addition of the external copper coils effectively increases this time to ∼7 ms. This led to better-confined/longer-lived field-reversed configuration (FRC) plasmas. The fringing fields generated by the external coils have the side effect of rendering external field measurements invalid. Such measurements were key to the previous method of excluded flux calculation [M. C. Thompson et al., Rev. Sci. Instrum. 83, 10D709 (2012)]. A new array of B-dot probes and Rogowski coils were installed to better determine the amount of flux leaked out of the system and ultimately provide a more robust measurement of plasma parameters related to pressure balance including the excluded flux radius. The B-dot probes are surface mountable chip inductors with inductance of 33 μH capable of measuring the DC magnetic field and transient field, due to resistive current decay in the wall/coils, when coupled with active integrators. The Rogowski coils measure the total change in current in each external coil (150 A/2 ms). Currents were also actively driven in the external coils. This renders the assumption of total flux conservation invalid which further complicates the analysis process. The ultimate solution to these issues and the record breaking resultant FRC lifetimes will be presented.

  6. Enhanced magnetic field probe array for improved excluded flux calculations on the C-2U advanced beam-driven field-reversed configuration plasma experiment

    Science.gov (United States)

    Roche, T.; Thompson, M. C.; Mendoza, R.; Allfrey, I.; Garate, E.; Romero, J.; Douglass, J.

    2016-11-01

    External flux conserving coils were installed onto the exterior of the C-2U [M. W. Binderbauer et al., Phys. Plasmas 22, 056110 (2015)] confinement vessel to increase the flux confinement time of the system. The 0.5 in. stainless steel vessel wall has a skin time of ˜5 ms. The addition of the external copper coils effectively increases this time to ˜7 ms. This led to better-confined/longer-lived field-reversed configuration (FRC) plasmas. The fringing fields generated by the external coils have the side effect of rendering external field measurements invalid. Such measurements were key to the previous method of excluded flux calculation [M. C. Thompson et al., Rev. Sci. Instrum. 83, 10D709 (2012)]. A new array of B-dot probes and Rogowski coils were installed to better determine the amount of flux leaked out of the system and ultimately provide a more robust measurement of plasma parameters related to pressure balance including the excluded flux radius. The B-dot probes are surface mountable chip inductors with inductance of 33 μH capable of measuring the DC magnetic field and transient field, due to resistive current decay in the wall/coils, when coupled with active integrators. The Rogowski coils measure the total change in current in each external coil (150 A/2 ms). Currents were also actively driven in the external coils. This renders the assumption of total flux conservation invalid which further complicates the analysis process. The ultimate solution to these issues and the record breaking resultant FRC lifetimes will be presented.

  7. Contactless Measurement of Magnetic Nanoparticles on Lateral Flow Strips Using Tunneling Magnetoresistance (TMR Sensors in Differential Configuration

    Directory of Open Access Journals (Sweden)

    Huaming Lei

    2016-12-01

    Full Text Available Magnetic nanoparticles (MNPs are commonly used in biomedical detection due to their capability to bind with some specific antibodies. Quantification of biological entities could be realized by measuring the magnetic response of MNPs after the binding process. This paper presents a contactless scanning prototype based on tunneling magnetoresistance (TMR sensors for quantification of MNPs present in lateral flow strips (LFSs. The sensing unit of the prototype composes of two active TMR elements, which are parallel and closely arranged to form a differential sensing configuration in a perpendicular magnetic field. Geometrical parameters of the configuration are optimized according to theoretical analysis of the stray magnetic field produced by the test line (T-line while strips being scanned. A brief description of our prototype and the sample preparation is presented. Experimental results show that the prototype exhibits the performance of high sensitivity and strong anti-interference ability. Meanwhile, the detection speed has been improved compared with existing similar techniques. The proposed prototype demonstrates a good sensitivity for detecting samples containing human chorionic gonadotropin (hCG at a concentration of 25 mIU/mL. The T-line produced by the sample with low concentration is almost beyond the visual limit and produces a maximum stray magnetic field some 0.247 mOe at the sensor in the x direction.

  8. Recent Results on Field Reversed Configurations from the Translation, Confinement and Sustainment Experiment

    Institute of Scientific and Technical Information of China (English)

    郭后扬

    2005-01-01

    The field-reversed configuration (FRC) offers an attractive alternative approach to magnetically confined fusion because of its extremely highβ, simple linear geometry, and natural divertor for helium ash removal. Multi-hundred eV and high density FRCs have been produced using the standard Field Reversed Theta Pinch (RFTP) method, with a confinement scaling that leads to fusion conditions. These FRCs are, however, limited to only tens of mWb fluxes and sub-msec lifetime. Recent progress has been made in building up the flux and sustaining the FRC current using Rotating Magnetic Fields (RMF) in the Translation, Sustainment, and Confinement (TCS) facility at the University of Washington. TCS has demonstrated formation and steadystate sustainment of standard, flux-confined, prolate FRCs. The RMF also provides stability for the n = 2 rotational mode, which is the dominant global instability observed experimentally.Simple calculations show that a strong radially inward force imposed by the RMF increases proportionally to any local outward deformation of the plasma crosssection. Evidence of this hasbeen experimentally demonstrated, and the effects of various RMF antenna geometries studied.High temperature FRCs could also be produced in TCS by translating high energy plasmoids formed in the normal theta pinch manner into the confinement chamber containing the RMF antennas. Extremely interesting results were obtained for this translation and capture process. The plasmoids can survive the violent dynamics of supersonic reflections off magnetic mirror structures, producing a stable high-β, near-FRC state with substantial flux conversion from toroidal to poloidal. This is a tribute not only to the robustness of FRCs, but also to the tendency of an FRC to assume a preferred state for a magnetized plasma. The magnetic helicity, as inferred by a simple interpretive model, is approximately preserved, possibly conforming to a high-β relaxation principle.

  9. Thermal diffusivity measurements in the photoacoustic open-cell configuration using simple signal normalization techniques

    Science.gov (United States)

    Balderas-López, J. A.; Mandelis, A.

    2001-09-01

    A generalized model for the open photoacoustic cell configuration (OPC) technique, involving one-dimensional heat diffusion across two layers, is presented. The analytical results are particularly suitable for applications with dielectric solids, such as polymers and resins. Two effective normalization procedures for simple and reliable measurement of the thermal diffusivity of this kind of materials using an OPC are also presented. The thermal diffusivity of three different materials (a dental resin, an epoxy resin, and a polymer foil) was measured and excellent agreement was obtained with some values reported in the literature. 2001 American Institute of Physics.

  10. An Adaptive Scheme for Robot Localization and Mapping with Dynamically Configurable Inter-Beacon Range Measurements

    Directory of Open Access Journals (Sweden)

    Arturo Torres-González

    2014-04-01

    Full Text Available This work is motivated by robot-sensor network cooperation techniques where sensor nodes (beacons are used as landmarks for range-only (RO simultaneous localization and mapping (SLAM. This paper presents a RO-SLAM scheme that actuates over the measurement gathering process using mechanisms that dynamically modify the rate and variety of measurements that are integrated in the SLAM filter. It includes a measurement gathering module that can be configured to collect direct robot-beacon and inter-beacon measurements with different inter-beacon depth levels and at different rates. It also includes a supervision module that monitors the SLAM performance and dynamically selects the measurement gathering configuration balancing SLAM accuracy and resource consumption. The proposed scheme has been applied to an extended Kalman filter SLAM with auxiliary particle filters for beacon initialization (PF-EKF SLAM and validated with experiments performed in the CONET Integrated Testbed. It achieved lower map and robot errors (34% and 14%, respectively than traditional methods with a lower computational burden (16% and similar beacon energy consumption.

  11. An adaptive scheme for robot localization and mapping with dynamically configurable inter-beacon range measurements.

    Science.gov (United States)

    Torres-González, Arturo; Martinez-de Dios, Jose Ramiro; Ollero, Anibal

    2014-04-25

    This work is motivated by robot-sensor network cooperation techniques where sensor nodes (beacons) are used as landmarks for range-only (RO) simultaneous localization and mapping (SLAM). This paper presents a RO-SLAM scheme that actuates over the measurement gathering process using mechanisms that dynamically modify the rate and variety of measurements that are integrated in the SLAM filter. It includes a measurement gathering module that can be configured to collect direct robot-beacon and inter-beacon measurements with different inter-beacon depth levels and at different rates. It also includes a supervision module that monitors the SLAM performance and dynamically selects the measurement gathering configuration balancing SLAM accuracy and resource consumption. The proposed scheme has been applied to an extended Kalman filter SLAM with auxiliary particle filters for beacon initialization (PF-EKF SLAM) and validated with experiments performed in the CONET Integrated Testbed. It achieved lower map and robot errors (34% and 14%, respectively) than traditional methods with a lower computational burden (16%) and similar beacon energy consumption.

  12. Electromagnetic measurements in the near field

    CERN Document Server

    Bienkowski, Pawel

    2012-01-01

    This book is devoted to the specific problems of electromagnetic field (EMF) measurements in the near field and to the analysis of the main factors which impede accuracy in these measurements. It focuses on careful and accurate design of systems to measure in the near field based on a thorough understanding of the fundamental engineering principles and on an analysis of the likely system errors. Beginning with a short introduction to electromagnetic fields with an emphasis on the near field, it them presents methods of EMF measurements in near field conditions. It details the factors limiting

  13. Modeling of the merging of two colliding field reversed configuration plasmoids

    Science.gov (United States)

    Wang, Guanqiong; Wang, Xiaoguang; Li, Lulu; Yang, Xianjun

    2016-06-01

    The field reversed configuration (FRC) is one of the candidate plasma targets for the magneto-inertial fusion, and a high temperature FRC can be formed by using the collision-merging technology. Although the merging process and mechanism of FRC are quite complicated, it is thinkable to build a simple model to investigate the macroscopic equilibrium parameters including the density, the temperature and the separatrix volume, which may play an important role in the collision-merging process of FRC. It is quite interesting that the estimates of the related results based on our simple model are in agreement with the simulation results of a two-dimensional magneto-hydrodynamic code (MFP-2D), which has being developed by our group since the last couple of years, while these results can qualitatively fit the results of C-2 experiments by Tri-alpha energy company. On the other hand, the simple model can be used to investigate how to increase the density of the merged FRC. It is found that the amplification of the density depends on the poloidal flux-increase factor and the temperature increases with the translation speed of two plasmoids.

  14. Formation and sustainment of field reversed configuration (FRC) plasmas by spheromak merging and neutral beam injection

    Science.gov (United States)

    Yamada, Masaaki

    2016-03-01

    This paper briefly reviews a compact toroid reactor concept that addresses critical issues for forming, stabilizing and sustaining a field reversed configuration (FRC) with the use of plasma merging, plasma shaping, conducting shells, neutral beam injection (NBI). In this concept, an FRC plasma is generated by the merging of counter-helicity spheromaks produced by inductive discharges and sustained by the use of neutral beam injection (NBI). Plasma shaping, conducting shells, and the NBI would provide stabilization to global MHD modes. Although a specific FRC reactor design is outside the scope of the present paper, an example of a promising FRC reactor program is summarized based on the previously developed SPIRIT (Self-organized Plasmas by Induction, Reconnection and Injection Techniques) concept in order to connect this concept to the recently achieved the High Performance FRC plasmas obtained by Tri Alpha Energy [Binderbauer et al, Phys. Plasmas 22,056110, (2015)]. This paper includes a brief summary of the previous concept paper by M. Yamada et al, Plasma Fusion Res. 2, 004 (2007) and the recent experimental results from MRX.

  15. Global Perturbation Configurations in a Composite Disc System with an Isopedic Magnetic Field

    CERN Document Server

    Lou, Y Q

    2005-01-01

    We construct stationary global configurations of both aligned and unaligned logarithmic spiral perturbations in a composite disc system of stellar and isopedically magnetized gaseous singular isothermal discs (SIDs) coupled by gravity. The thin gaseous SID is threaded across by a vertical magnetic field B_z with a constant ratio of the surface gas mass density to B_z. There exist two classes of stationary magnetohydrodynamic (MHD) solutions with in-phase and out-of-phase density perturbations. For both aligned and unaligned cases with azimuthal periodicities |m|\\geq 2 (m is an integer), there may be two, one, and no solution situations, depending on the chosen parameters. For the transition criteria from an axisymmetric equilibrium to aligned secular bar-like instabilities, the corresponding T/|W| ratio can be much lower than the oft-quoted value of T/|W|\\sim 0.14, where T is the total rotational kinetic energy and W is the total gravitational potential energy plus the magnetic energy. The T/|W| ratios for th...

  16. Magnetic field measurements of JT-60SA CS model coil

    Energy Technology Data Exchange (ETDEWEB)

    Obana, Tetsuhiro, E-mail: obana.tetsuhiro@LHD.nifs.ac.jp [National Institute for Fusion Science, 322-6 Oroshi, Toki, Gifu 509-5292 (Japan); Takahata, Kazuya; Hamaguchi, Shinji; Chikaraishi, Hirotaka; Mito, Toshiyuki; Imagawa, Shinsaku [National Institute for Fusion Science, 322-6 Oroshi, Toki, Gifu 509-5292 (Japan); Kizu, Kaname; Murakami, Haruyuki; Natsume, Kyohei; Yoshida, Kiyoshi [Japan Atomic Energy Agency, 801-1 Mukoyama, Naka, Ibaraki 311-0193 (Japan)

    2015-01-15

    Highlights: • Magnetic fields of the JT-60SA CS model coil were measured. • While the coil current was held constant at 20 kA, magnetic fields varied slightly with several different long time constants. • We investigated coils consisting of CIC conductors and having long time constants. - Abstract: In a cold test of the JT-60SA CS model coil, which has a quad-pancake configuration consisting of a Nb{sub 3}Sn cable-in-conduit (CIC) conductor, magnetic fields were measured using Hall sensors. For a holding coil current of 20 kA, measured magnetic fields varied slightly with long time constants in the range 17–571 s, which was much longer than the time constant derived from a measurement using a short straight sample. To validate the measurements, the magnetic fields of the model coil were calculated using a computational model representing the positions of Nb{sub 3}Sn strands inside the CIC conductor. The calculated results were in good agreement with the measurements. Consequently, the validity of the magnetic field measurements was confirmed. Next, we investigated other coils consisting of CIC conductors and having long time constants. The only commonality among the coils was the use of CIC conductors. At present, there is no obvious way to prevent generation of such magnetic-field variations with long time constants.

  17. Torsional mode ultrasonic helical waveguide sensor for re-configurable temperature measurement

    Science.gov (United States)

    Periyannan, Suresh; Rajagopal, Prabhu; Balasubramaniam, Krishnan

    2016-06-01

    This paper introduces an ultrasonic torsional mode based technique, configured in the form of a helical "spring-like" waveguide, for multi-level temperature measurement. The multiple sensing levels can be repositioned by stretching or collapsing the spring to provide simultaneous measurements at different desired spacing in a given area/volume. The transduction is performed using piezo-electric crystals that generate and receive T(0,1) mode in a pulse echo mode. The gage lengths and positions of measurements are based on machining multiple reflector notches in the waveguide at required positions. The time of fight (TOF) measurements between the reflected signals from the notches provide local temperatures that compare well with co-located thermocouples.

  18. Torsional mode ultrasonic helical waveguide sensor for re-configurable temperature measurement

    Directory of Open Access Journals (Sweden)

    Suresh Periyannan

    2016-06-01

    Full Text Available This paper introduces an ultrasonic torsional mode based technique, configured in the form of a helical “spring-like” waveguide, for multi-level temperature measurement. The multiple sensing levels can be repositioned by stretching or collapsing the spring to provide simultaneous measurements at different desired spacing in a given area/volume. The transduction is performed using piezo-electric crystals that generate and receive T(0,1 mode in a pulse echo mode. The gage lengths and positions of measurements are based on machining multiple reflector notches in the waveguide at required positions. The time of fight (TOF measurements between the reflected signals from the notches provide local temperatures that compare well with co-located thermocouples.

  19. Analytical and numerical quantification and comparison of the local electric field in the tissue for different electrode configurations

    Directory of Open Access Journals (Sweden)

    Pavlin Mojca

    2007-10-01

    Full Text Available Abstract Background Electrochemotherapy and gene electrotransfer are novel promising treatments employing locally applied high electric pulses to introduce chemotherapeutic drugs into tumor cells or genes into target cells based on the cell membrane electroporation. The main focus of this paper was to calculate analytically and numerically local electric field distribution inside the treated tissue in two dimensional (2D models for different plate and needle electrode configurations and to compare the local electric field distribution to parameter U/d, which is widely used in electrochemotherapy and gene electrotransfer studies. We demonstrate the importance of evaluating the local electric field distribution in electrochemotherapy and gene electrotransfer. Methods We analytically and numerically analyze electric field distribution based on 2D models for electrodes and electrode configurations which are most widely used in electrochemotherapy and gene electrotransfer. Analytical calculations were performed by solving the Laplace equation and numerical calculations by means of finite element method in two dimensions. Results We determine the minimal and maximal E inside the target tissue as well as the maximal E over the entire treated tissue for the given electrode configurations. By comparing the local electric field distribution calculated for different electrode configurations to the ratio U/d, we show that the parameter U/d can differ significantly from the actual calculated values of the local electric field inside the treated tissue. By calculating the needed voltage to obtain E > U/d inside the target tissue, we showed that better electric field distribution can be obtained by increasing the number and changing the arrangement of the electrodes. Conclusion Based on our analytical and numerical models of the local electric field distribution we show that the applied voltage, configuration of the electrodes and electrode position need to be

  20. Polynomial Collocation for Handling an Inaccurately Known Measurement Configuration in Electrical Impedance Tomography

    DEFF Research Database (Denmark)

    Hyvönen, Niina; Kaarnioja, V.; Mustonen, L.

    2017-01-01

    The objective of electrical impedance tomography is to reconstruct the internal conductivity of a physical body based on measurements of current and potential at a finite number of electrodes attached to its boundary. Although the conductivity is the quantity of main interest in impedance...... tomography, a real-world measurement configuration includes other unknown parameters as well: The information on the contact resistances, electrode positions, and body shape is almost always incomplete. In this work, the dependence of the electrode measurements on all aforementioned model properties...... is parametrized via polynomial collocation. The availability of such a parametrization enables efficient simultaneous reconstruction of the conductivity and other unknowns by a Newton-type output least squares algorithm, which is demonstrated by two-dimensional numerical experiments based on both noisy simulated...

  1. Approaches for Controlling the Level in Water/steam Separators of a DSG Solar Field Configured in Recirculation Mode

    Energy Technology Data Exchange (ETDEWEB)

    Valenzuela, L.; Zarza, E.; Leon, J.

    2006-07-01

    The DISS plant located at the Plataforma Solar de Almeria (PSA) serves as test bed to investigate under real solar conditions the direct steam generation (DSG) in a parabolic trough collectors field working as the boiler and superheater of a Rankine steam cycle. This solar field can be configured in different operation modes (recirculation, once-TROUGH and injection modes) being the recirculation mode the most efficient from the stability and control points of view. Within the INDITEP project, financed by the EU Commission (2002-2005), one of the tasks performed has been testing new components for the solar field with the system configured in recirculation mode. One disadvantage of this configuration is the cost of the facility; it is needed a middle water-steam separator in the solar field, which separates evaporation and superheating sections, and a recirculation pump. Reduction of the liquid inventory in the process, i.e. the volume of the middle separator tank, will reduce the cost and parasitic loads of the solar field but it requires an efficient control of the liquid level inside the separator and, with the current layout of the solar field, that means an efficient control of the inlet water flow to the solar field, affecting also to the recirculation ratio (ratio between the recirculation flow and feed water flow) established for nominal conditions. The paper presents simulation and experimental results obtained using different classical and advanced control strategies. (Author)

  2. Twenty-channel bolometer array for studying impurity radiation and transport in the TCS field-reversed configuration

    Science.gov (United States)

    Kostora, M. R.; Hsu, S. C.; Wurden, G. A.

    2006-10-01

    A bolometer array diagnostic has been developed for the University of Washington Translation, Confinement, and Sustainment (TCS) field-reversed configuration (FRC) experiment in order to measure radially resolved total radiated power per unit length of the FRC. This will provide radiation energy loss information, useful in power balance and impurity studies. The 20-element photodiode bolometer will be mounted at the midplane of the TCS cylindrical vacuum chamber to view the rotating magnetic field (RMF) generated FRC plasma. Key features of this new bolometer array are (1) extensive electrical shielding against the RMF, (2) robust electrical isolation, (3) trans-impedance amplifiers using a microcoax interface at the array and a fiber optic interface to the screen room, and (4) a custom glass-on-metal socket for the 20-element photodiode chip to ensure high vacuum compatibility. The bolometer array can be retracted behind a gate valve using a stepper motor to protect it during vacuum chamber bakeout. The slit assembly housing is interchangeable to provide flexibility for the viewing sightlines.

  3. Constrained sessile drop as a new configuration to measure low surface tension in lung surfactant systems.

    Science.gov (United States)

    Yu, Laura M Y; Lu, James J; Chan, Yawen W; Ng, Amy; Zhang, Ling; Hoorfar, Mina; Policova, Zdenka; Grundke, Karina; Neumann, A Wilhelm

    2004-08-01

    Existing methodology for surface tension measurements based on drop shapes suffers from the shortcoming that it is not capable to function at very low surface tension if the liquid dispersion is opaque, such as therapeutic lung surfactants at clinically relevant concentrations. The novel configuration proposed here removes the two big restrictions, i.e., the film leakage problem that is encountered with such methods as the pulsating bubble surfactometer as well as the pendant drop arrangement, and the problem of the opaqueness of the liquid, as in the original captive bubble arrangement. A sharp knife edge is the key design feature in the constrained sessile drop that avoids film leakage at low surface tension. The use of the constrained sessile drop configuration in conjunction with axisymmetric drop shape analysis to measure surface tension allows complete automation of the setup. Dynamic studies with lung surfactant can be performed readily by changing the volume of a sessile drop, and thus the surface area, by means of a motor-driven syringe. To illustrate the validity of using this configuration, experiments were performed using an exogenous lung surfactant preparation, bovine lipid extract surfactant (BLES) at 5.0 mg/ml. A comparison of results obtained for BLES at low concentration between the constrained sessile drop and captive bubble arrangement shows excellent agreement between the two approaches. When the surface area of the BLES film (0.5 mg/ml) was compressed by about the same amount in both systems, the minimum surface tensions attained were identical within the 95% confidence limits.

  4. Plane polymer configurations enclosing a fixed area in an electric field: generating functional and statistical mechanical properties

    NARCIS (Netherlands)

    Khandekar, D.C.; Wiegel, F.W.

    1993-01-01

    The statistical mechanical properties of plane polymer configurations which enclose a fixed area and are subject to an external electric field are investigated. For this purpose an exact expression for the generating functional is obtained and subsequently used to derive: (a) the distribution functi

  5. Measuring vector magnetic fields in solar prominences

    CERN Document Server

    Suárez, D Orozco; Bueno, J Trujillo

    2012-01-01

    We present spectropolarimetric observations in the He I 1083.0 nm multiplet of a quiescent, hedgerow solar prominence. The data were taken with the Tenerife Infrared Polarimeter attached to the German Vacuum Tower Telescope at the Observatorio del Teide (Tenerife; Canary Islands; Spain). The observed He I circular and linear polarization signals are dominated by the Zeeman effect and by atomic level polarization and the Hanle effect, respectively. These observables are sensitive to the strength and orientation of the magnetic field vector at each spatial point of the field of view. We determine the magnetic field vector of the prominence by applying the HAZEL inversion code to the observed Stokes profiles. We briefly discuss the retrieved magnetic field vector configuration.

  6. Defining and measuring transnational fields

    OpenAIRE

    Molina, J.; Petermann, S.; Herz, A.

    2012-01-01

    Transnational social fields and transnational social spaces are concepts used interchangeably in transnational literature. Although both of them refer to the complex of connections between borders, each of them represents a different – and complementary – perspective. In this paper, it will be argued that the adoption of the social networks approach by transnational studies actually inherited two different traditions for studying relational phenomena: the anthropological egocentric or persona...

  7. Crystal field splitting of the 4f 5d electronic configuration of Pr 3+ ions in wide band gap fluoride dielectric crystals

    Science.gov (United States)

    Sarantopoulou, E.; Kollia, Z.; Cefalas, A. C.; Semashko, V. V.; Yu. Abdulsabirov, R.; Naumov, A. K.; Korableva, S. L.; Szczurek, T.; Kobe, S.; McGuiness, P. J.

    2002-07-01

    The absorption and the laser-induced fluorescence spectra of Pr 3+ ion in YF 3, LaF 3, KY 3 F 10 and LiLuF 4, single crystal hosts were obtained in the vacuum ultraviolet region of the spectrum. The energy position and the spacing of the levels of the 4f 5d electronic configuration depend on the host matrix. In addition, strong vacuum ultraviolet emission bands were observed, following crystal excitation at 157 nm with the molecular fluorine laser. The emission bands were due to the interconfigurational 4 f 5 d→4 f2 dipole-allowed transitions in Pr 3+ ions, and they were assigned to the transitions between the edge of the lowest Stark component of the 4f 5d electronic configuration and the levels of the 4f 2 electronic configuration. The VUV spectra can be interpreted by applying the crystal field model, and taking into consideration that lanthanide contraction of the 4f n-1 5d electronic configurations of the rare earth ions, and shielding of the positive ion charge from the electrons in the 4f n electronic configuration is taking place. Finally, a new method for monitoring the concentration of the rare earth ions in wide band gap fluoride dielectric crystals in a non-destructive way, by measuring magnetic dipole moments with the vibrating sample magnetometer (VSM) method, is presented for the first time to our knowledge for this type of crystals.

  8. Cross-field motion of plasma blob-filaments and related particle flux in an open magnetic field line configuration on QUEST

    Energy Technology Data Exchange (ETDEWEB)

    Liu, H.Q., E-mail: hqliu@ipp.ac.cn [Institute of Plasma Physics, Chinese Academy of Sciences, Hefei, Anhui 230031 (China); Interdisciplinary Graduate School of Engineering Sciences, Kyushu University, Kasuga, Fukuoka 8168580 (Japan); Hanada, K. [Research Institute for Applied Mechanics, Kyushu University, Kasuga, Fukuoka 8168580 (Japan); Nishino, N. [Graduate School of Engineering, Hiroshima University, Hiroshima 7398511 (Japan); Ogata, R.; Ishiguro, M. [Interdisciplinary Graduate School of Engineering Sciences, Kyushu University, Kasuga, Fukuoka 8168580 (Japan); Gao, X. [Institute of Plasma Physics, Chinese Academy of Sciences, Hefei, Anhui 230031 (China); Zushi, H.; Nakamura, K.; Fujisawa, A.; Idei, H.; Hasegawa, M. [Research Institute for Applied Mechanics, Kyushu University, Kasuga, Fukuoka 8168580 (Japan)

    2013-07-15

    Blob-filaments have been observed by combined measurement with a fast camera and a movable Langmuir probe in an open magnetic field line configuration of electron cyclotron resonance (ECR) heating plasma in QUEST. Blob-filaments extended along field lines do correspond to over-dense plasma structures and propagated across the field lines to the outer wall. The radial velocity of the blob structure, V{sub b}, was obtained by three methods and was dominantly driven by the E × B force. The radial velocity, size of the blob showed good agreements with the results obtained by sheath-connected interchange theoretical model. V{sub b} corresponds to roughly 0.02–0.07 of the local sound speed (C{sub s}) in QUEST. The higher moments (skewness S and kurtosis K) representing the shape of PDF of density fluctuation are studied. Their least squares fitting with quadratic polynomial is K = (1.60 ± 0.27)S{sup 2} − (0.46 ± 0.20). The larger blob structures, occurring only 10% of the time, can carry more than 60% loss of the entire radial particle flux.

  9. Optimum electrode configuration selection for electrical resistance change based damage detection in composites using an effective independence measure

    Science.gov (United States)

    Escalona, Luis; Díaz-Montiel, Paulina; Venkataraman, Satchi

    2016-04-01

    Laminated carbon fiber reinforced polymer (CFRP) composite materials are increasingly used in aerospace structures due to their superior mechanical properties and reduced weight. Assessing the health and integrity of these structures requires non-destructive evaluation (NDE) techniques to detect and measure interlaminar delamination and intralaminar matrix cracking damage. The electrical resistance change (ERC) based NDE technique uses the inherent changes in conductive properties of the composite to characterize internal damage. Several works that have explored the ERC technique have been limited to thin cross-ply laminates with simple linear or circular electrode arrangements. This paper investigates a method of optimum selection of electrode configurations for delamination detection in thick cross-ply laminates using ERC. Inverse identification of damage requires numerical optimization of the measured response with a model predicted response. Here, the electrical voltage field in the CFRP composite laminate is calculated using finite element analysis (FEA) models for different specified delamination size and locations, and location of ground and current electrodes. Reducing the number of sensor locations and measurements is needed to reduce hardware requirements, and computational effort needed for inverse identification. This paper explores the use of effective independence (EI) measure originally proposed for sensor location optimization in experimental vibration modal analysis. The EI measure is used for selecting the minimum set of resistance measurements among all possible combinations of selecting a pair of electrodes among the n electrodes. To enable use of EI to ERC required, it is proposed in this research a singular value decomposition SVD to obtain a spectral representation of the resistance measurements in the laminate. The effectiveness of EI measure in eliminating redundant electrode pairs is demonstrated by performing inverse identification of

  10. Resolution-of-identity stochastic time-dependent configuration interaction for dissipative electron dynamics in strong fields.

    Science.gov (United States)

    Klinkusch, Stefan; Tremblay, Jean Christophe

    2016-05-14

    In this contribution, we introduce a method for simulating dissipative, ultrafast many-electron dynamics in intense laser fields. The method is based on the norm-conserving stochastic unraveling of the dissipative Liouville-von Neumann equation in its Lindblad form. The N-electron wave functions sampling the density matrix are represented in the basis of singly excited configuration state functions. The interaction with an external laser field is treated variationally and the response of the electronic density is included to all orders in this basis. The coupling to an external environment is included via relaxation operators inducing transition between the configuration state functions. Single electron ionization is represented by irreversible transition operators from the ionizing states to an auxiliary continuum state. The method finds its efficiency in the representation of the operators in the interaction picture, where the resolution-of-identity is used to reduce the size of the Hamiltonian eigenstate basis. The zeroth-order eigenstates can be obtained either at the configuration interaction singles level or from a time-dependent density functional theory reference calculation. The latter offers an alternative to explicitly time-dependent density functional theory which has the advantage of remaining strictly valid for strong field excitations while improving the description of the correlation as compared to configuration interaction singles. The method is tested on a well-characterized toy system, the excitation of the low-lying charge transfer state in LiCN.

  11. Critical Configuration and Physics Measurements for Assemblies of U(93.15)O2 Fuel Rods

    Energy Technology Data Exchange (ETDEWEB)

    Margaret A. Marshall

    2013-03-01

    A series of critical experiments were completed in 1962-1965 at Oak Ridge National Laboratory’s (ORNL’s) Critical Experiments Facility (CEF) in support of the Medium-Power Reactor Experiments (MPRE) program. In the late 1950s, efforts were made to study “power plants for the production of electrical power in space vehicles.”(a) The MPRE program was a part of those efforts and studied the feasibility of a stainless-steel system, boiling potassium 1 MW(t), or about 140 kW(e), reactor. The program was carried out in [fiscal years] 1964, 1965, and 1966. A summary of the program’s effort was compiled in 1967. The delayed critical experiments were a mockup of a small, potassium-cooled space power reactor for validation of reactor calculations and reactor physics methods. Initial experiments, performed in November and December of 1962, consisted of a core of unmoderated stainless-steel tubes, each containing 26 UO2 fuel pellets, surrounded by a graphite reflector. Measurements were made to determine critical reflector arrangements, fission-rate distributions, and cadmium ratio distributions. Subsequent experiments used beryllium reflectors and also measured the reactivity for various materials placed in the core. “The [assemblies were built] on [a] vertical assembly machine so that the movable part was the core and bottom reflector.”(Reference 1) The experiment studied in this evaluation was the first of the series and had the fuel tubes packed tightly into a 22.87 cm outside diameter (OD) core tank. Two critical configurations were found by varying the amount of graphite reflector (References 1 and 2). Once the critical configurations had been achieved, various measurements of reactivity, relative axial and radial activation rates of 235U, , and cadmium ratios were performed. The cadmium ratio, reactivity, and activation rate measurements performed on the critical configurations are described in Sections 1.3, 1.4 and 1.7, respectively. Information for this

  12. Critical Configuration and Physics Measurements for Assemblies of U(93.15)O2 Fuel Rods

    Energy Technology Data Exchange (ETDEWEB)

    Margaret A. Marshall

    2012-09-01

    A series of critical experiments were completed in 1962-1965 at Oak Ridge National Laboratory’s (ORNL’s) Critical Experiments Facility (CEF) in support of the Medium-Power Reactor Experiments (MPRE) program. In the late 1950s, efforts were made to study “power plants for the production of electrical power in space vehicles.”(a) The MPRE program was a part of those efforts and studied the feasibility of a stainless-steel system, boiling potassium 1 MW(t), or about 140 kW(e), reactor. The program was carried out in [fiscal years] 1964, 1965, and 1966. A summary of the program’s effort was compiled in 1967. The delayed critical experiments were a mockup of a small, potassium-cooled space power reactor for validation of reactor calculations and reactor physics methods. Initial experiments, performed in November and December of 1962, consisted of a core of unmoderated stainless-steel tubes, each containing 26 UO2 fuel pellets, surrounded by a graphite reflector. Measurements were made to determine critical reflector arrangements, fission-rate distributions, and cadmium ratio distributions. Subsequent experiments used beryllium reflectors and also measured the reactivity for various materials placed in the core. “The [assemblies were built] on [a] vertical assembly machine so that the movable part was the core and bottom reflector.”(Reference 1) The experiment studied in this evaluation was the first of the series and had the fuel tubes packed tightly into a 22.87 cm outside diameter (OD) core tank. Two critical configurations were found by varying the amount of graphite reflector (References 1 and 2). Once the critical configurations had been achieved, various measurements of reactivity, relative axial and radial activation rates of 235U, , and cadmium ratios were performed. The cadmium ratio, reactivity, and activation rate measurements performed on the critical configurations are described in Sections 1.3, 1.4 and 1.7, respectively. Information for this

  13. Development of a Thomson scattering system and its use in a rotating magnetic field driven field-reversed configurations plasma

    Science.gov (United States)

    Lee, Kiyong

    The Thomson scattering system has been utilized on the Translation Confinement & Sustainment Upgrade (TCSU) experiment to measure the electron temperature and density. The system uses five polychromators from General Atomics attached with three pre-amplifier modules from Princeton Plasma Physics Laboratory to measure five spatial points during a single plasma discharge. The diagnostic consisting of various mechanical and optical components is introduced, followed by the calibration procedure of the system. For validating measurements, the electron temperature and the relative density obtained from Thomson scattering are compared with measurements from the Langmuir probe. Both measurements are in good agreement. A power scan was conducted by applying different voltages to the rotating magnetic field (RMF) current drive to observe the scaling properties of temperature and density for even-parity and odd-parity RMF operations. Also, a discrepancy is observed when comparing the density based on pressure-balance with localized measurements. Further analysis indicates a possibility of an ion-temperature-gradient, presumably due to ion cyclotron heating, present during steady-state operation.

  14. Design of modular coils for a quasi-axisymmetric stellarator with a flexible control of the magnetic field configuration

    Energy Technology Data Exchange (ETDEWEB)

    Shimizu, A.; Okamura, S.; Isobe, M.; Suzuki, C.; Nishimura, S.; Watari, T.; Matsuoka, K.

    2002-08-01

    A design of the modular coil system for CHS-qa has been made for the plasma configuration '2b32' with the aspect ratio 3.2. The magnetic field strength and the major radius are 1.5 T and 1.5 m, respectively. The normal component of magnetic field produced by the modular coils is minimized on the plasma boundary to obtain the optimum coil design. We put engineering constraint on the distance between adjacent modular coils and the radius of coil curvature. The dependence of the residual normal component of the field on these conditions is examined, and the realistic values for them are selected. Additional coils to control various properties of the magnetic field configuration (the rotational transform, the magnetic well depth, etc.) have been designed and a flexibility of the magnetic field configuration is realized. For the case that the rotational transform crosses the low-order rational value resulting in magnetic islands, the residues of islands are evaluated with which a further improvement of coil design can be made to eliminate magnetic islands. (author)

  15. N-body problem in $R^n$: Necessary conditions for a constant configuration measure

    Directory of Open Access Journals (Sweden)

    Kal Zare

    2008-11-01

    Full Text Available A formulation of the N-body problem is presented in which $m_{i}$ and $r_{i}in mathbb{R}^d$ are the mass and the position vector of the i-th body, $ x=(sqrt{m_{1}}r_{1},dots ,sqrt{m_{N}}r_{N}in mathbb{R}^n$ and $ n=dN$ ($d=1,2,3$. The configuration measure $ Z =|x|F $, where $F$ is the Poincare's force function, which plays an important role in this formulation. The orbit plane is a two dimensional linear subspace of $ mathbb{R}^n $ spanned by the position vector $x$ and the velocity vector $dot{x}$. The N-body motion in $mathbb{R}^n$ has been decomposed into an orbit in the orbit plane and the instantaneous orientation of the orbit plane. For a solution to stay on a level manifold of $Z$, it is necessary that the orbit in the orbit plane be elliptic ($h0$ where h is the total energy. The instantaneous orientation of the orbit plane can be obtained by integration of certain differential equations. These possible solutions include the central configuration solutions in which the orbit plane is fixed in $mathbb{R}^n$.

  16. Compensation of the magnetization current induced sextupole error at LHC injection field by short lumped permanent sextupole magnets, incorporated into the end configuration of superconducting dipoles

    CERN Document Server

    Asner, A

    1985-01-01

    Compensation of the magnetization current induced sextupole error at LHC injection field by short lumped permanent sextupole magnets, incorporated into the end configuration of superconducting dipoles

  17. Measurement of nonlinear refractive index based on multiple configuration of FBG in generating multi wavelength

    Science.gov (United States)

    Abdullah, Mohd Nizam; Shaari, Sahbudin; Ehsan, Abang Annuar; Menon, Susthitha; Zakaria, Osman

    2015-06-01

    A reliable method for measurement of the nonlinear refractive index through application of multi wavelength phenomenon. Multi wavelength realisation based on Erbium doped fibre laser (EDFL) is proposed and experimentally demonstrated. A combination of 15 m high efficiency Erbium doped fibre (EDF) and a 20 m Photonic Crystal Fibre (PCF) as main catalyst to suppress the homogenous broadening of EDF and to obtain highly stability of multi wavelength through insertion of a set of fibre Bragg gratings (FBGs) in the cavity. This PCF has zero dispersion of 1040 nm which mismatch from transmission window of 1550 nm. A reliable repeatability of multi wavelength based on multiple configuration of FBGs less than 0.2% obtained. This consistent results influence in determination of nonlinear refractive index by relation of four wave mixing (FWM).

  18. Laboratory Measurements of Astrophysical Magnetic Fields

    Science.gov (United States)

    Murphy, C. D.; Miniati, F.; Edwards, M.; Mithen, J.; Bell, A. R.; Constantin, C.; Everson, E.; Schaeffer, D.; Niemann, C.; Ravasio, A.; Brambrink, E.; Benuzzi-Mounaix, A.; Koenig, M.; Gregory, C.; Woolsey, N.; Park, H.-S.; Remington, B.; Ryutov, D.; Bingham, R.; Gargate, L.; Spitkovsky, A.; Gregori, G.

    2010-11-01

    It has been proposed that high Mach number collisionless shocks propagating in an initially unmagnetized plasma play a major role in the magnetization of large scale structures in the Universe. A detailed study of the experimental configuration necessary to scale such environments down to laboratory dimensions will be presented. We will show initial results from preliminary experiments conducted at the Phoenix laser (UCLA) and the LULI laser (Ecole Polytechnique) where collisionless shocks are generated by the expansion of exploding foils driven by energetic laser beams. The time evolution of the magnetic field is probed with induction coils placed at 10 cm from the laser focus. We will discuss various mechanisms of magnetic field generation and compare them with the experimental results.

  19. Magnetic Field Measurement on a Refined Kicker

    CERN Document Server

    Fan, Tai-Ching; Lin, Fu-Yuan

    2005-01-01

    To prepare for the operation of top-up mode and increase the efficiency of injection at storage ring, National Synchrotron Radiation Research Center (NSRRC) has upgraded the kicker magnets and power supply. We have built up a new magnetic field measurement system to test the kicker. This system, including a search coil and a coil loop, can map the field and take the first integral of field automatically. We also simulate the trajectory of electron beam by pulsed wire method of field measurement. We analyze the performance of the kicker system in this paper.

  20. Bridging particle and wave sensitivity in a configurable detector of positive operator-valued measures.

    Science.gov (United States)

    Puentes, Graciana; Lundeen, Jeff S; Branderhorst, Matthijs P A; Coldenstrodt-Ronge, Hendrik B; Smith, Brian J; Walmsley, Ian A

    2009-02-27

    We report an optical detector with tunable positive operator-valued measures. The device is based on a combination of weak-field homodyne techniques and photon-number-resolving detection. The resulting positive operator-valued measures can be continuously tuned from Fock-state projectors to a variety of phase-dependent quantum-state measurements by adjusting different system parameters such as local oscillator coupling, amplitude, and phase, allowing thus not only detection but also preparation of exotic quantum states. Experimental tomographic reconstructions of classical benchmark states are presented as a demonstration of the detector capabilities.

  1. Attracting Students to the Field of Measurement

    Science.gov (United States)

    Finney, Sara J.; Pastor, Dena A.

    2012-01-01

    To address the shortage of professionals in measurement, it is essential that we make young career-seekers aware that measurement is an option as a profession. In this paper, we discuss how creating a strong pipeline of students into our field involves personal interactions between faculty representing the graduate programs in measurement and…

  2. FRC Lifetime Studies for the Field Reversed Configuration Heating Experiment (FRCHX)

    Science.gov (United States)

    2011-06-01

    the other and that are marxed when discharged (a re-configured Shiva Star bank module). The Main bank current is crowbarred when its peak current...diffusion time would be required. The Shiva Star high-energy capacitor bank is a seventh bank for FRCHX when compression heating tests are performed...The Shiva bank is comprised of thirty six 36- F bank modules, and the bank delivers 11 ~ 12 MA of current to drive the liner implosion around the

  3. Calculation and measurement of electric field under HVDC transmission lines

    Science.gov (United States)

    Kasdi, A.; Zebboudj, Y.; Yala, H.

    2007-03-01

    A stable corona discharge in a two conductors-to-plane configuration is analysed in this paper. A linear biased probe, without end-effect, has been adapted to a linear geometry and is used for the first time to measure the ground-plane current density and electric field during the bipolar corona. The values of the electric field and the current density are maximum under the two coronating conductors and decrease when moving away from them. Furthermore, a hybrid technique is developed to obtain a general solution of the governing equations of the coupled space-charge and electric field problem. The technique is to use the finite-element method (FEM) to solve Poisson's equation, and the method of characteristic (MOC) to find the charge density from a current-continuity relation. The model avoids resorting to the Deutsch assumption. The computed values are in good agreement with experimental data.

  4. Calculated and measured fields in superferric wiggler magnets

    Energy Technology Data Exchange (ETDEWEB)

    Blum, E.B.; Solomon, L. [Brookhaven National Lab., Upton, NY (United States)

    1995-02-01

    Although Klaus Halbach is widely known and appreciated as the originator of the computer program POISSON for electromagnetic field calculation, Klaus has always believed that analytical methods can give much more insight into the performance of a magnet than numerical simulation. Analytical approximations readily show how the different aspects of a magnet`s design such as pole dimensions, current, and coil configuration contribute to the performance. These methods yield accuracies of better than 10%. Analytical methods should therefore be used when conceptualizing a magnet design. Computer analysis can then be used for refinement. A simple model is presented for the peak on-axis field of an electro-magnetic wiggler with iron poles and superconducting coils. The model is applied to the radiator section of the superconducting wiggler for the BNL Harmonic Generation Free Electron Laser. The predictions of the model are compared to the measured field and the results from POISSON.

  5. Dark field electron holography for strain measurement

    Energy Technology Data Exchange (ETDEWEB)

    Beche, A., E-mail: armand.beche@fei.com [CEA-Grenoble, INAC/SP2M/LEMMA, F-38054 Grenoble (France); Rouviere, J.L. [CEA-Grenoble, INAC/SP2M/LEMMA, F-38054 Grenoble (France); Barnes, J.P.; Cooper, D. [CEA-LETI, Minatec Campus, F-38054 Grenoble (France)

    2011-02-15

    Dark field electron holography is a new TEM-based technique for measuring strain with nanometer scale resolution. Here we present the procedure to align a transmission electron microscope and obtain dark field holograms as well as the theoretical background necessary to reconstruct strain maps from holograms. A series of experimental parameters such as biprism voltage, sample thickness, exposure time, tilt angle and choice of diffracted beam are then investigated on a silicon-germanium layer epitaxially embedded in a silicon matrix in order to obtain optimal dark field holograms over a large field of view with good spatial resolution and strain sensitivity. -- Research Highlights: {yields} Step by step explanation of the dark field electron holography technique. {yields} Presentation of the theoretical equations to obtain quantitative strain map. {yields} Description of experimental parameters influencing dark field holography results. {yields} Quantitative strain measurement on a SiGe layer embedded in a silicon matrix.

  6. High-field bipolar loss measurement apparatus

    Science.gov (United States)

    Weldon, D.; Thullen, P.; Wollan, J.

    1980-09-01

    An apparatus was constructed to measure dissipation in superconducting wire in high alternating fields. The circuit incorporates a pair of locomotive traction motors as the capacitive circuit element for the bipolar swing. The design, construction and operating characteristics of the field coil and the associated circuitry are described.

  7. Formation of uniform fringe pattern free from diffraction noise at LDA measurement volume using holographic imaging configuration

    Science.gov (United States)

    Ghosh, Abhijit; Nirala, A. K.

    2016-05-01

    In the present study we have proposed a technique for improving fringe quality at laser Doppler anemometry measurement volume in real time using single hololens imaging configuration over conventional imaging configuration with Gaussian beam optics. In order to remove interference fringe gradients as well as higher order diffraction noise formed at measurement volume in the former approach, a combined hololens imaging system has also been proposed. For qualitative as well as quantitative analysis of fringes formed at measurement volume, atomic force microscopy (AFM) analysis has been performed.

  8. Lightning Magnetic Field Measurements around Langmuir Laboratory

    Science.gov (United States)

    Stock, M.; Krehbiel, P. R.; Rison, W.; Aulich, G. D.; Edens, H. E.; Sonnenfeld, R. G.

    2010-12-01

    In the absence of artificial conductors, underground lightning transients are produced by diffusion of the horizontal surface magnetic field of a return stroke vertically downward into the conducting earth. The changing magnetic flux produces an orthogonal horizontal electric field, generating a dispersive, lossy transverse electromagnetic wave that penetrates a hundred meters or more into the ground according to the skin depth of the medium. In turn, the electric field produces currents that flow toward or away from the channel to ground depending on the stroke polarity. The underground transients can produce large radial horizontal potential gradients depending on the distance from the discharge and depth below the surface. In this study we focus on the surface excitation field. The goal of the work is to compare measurements of surface magnetic field waveforms B(t) at different distances from natural lightning discharges with simple and detailed models of the return stroke fields. In addition to providing input to the diffusion mechanism, the results should aid in further understanding return stroke field generation processes. The observational data are to be obtained using orthogonal sets of straightened Rogowski coils to measure magnetic field waveforms in N-S and E-W directions. The waveforms are sampled at 500 kS/s over 1.024 second time intervals and recorded directly onto secure digital cards. The instrument operates off of battery power for several days or weeks at a time in remote, unattended locations and measures magnetic field strengths of up to several tens of amperes/meter. The observations are being made in conjunction with collocated slow electric field change measurements and under good 3-D lightning mapping array (LMA) and fast electric field change coverage.

  9. Thermal-Diffusivity Measurements of Mexican Citrus Essential Oils Using Photoacoustic Methodology in the Transmission Configuration

    Science.gov (United States)

    Muñoz, G. A. López; González, R. F. López; López, J. A. Balderas; Martínez-Pérez, L.

    2011-05-01

    Photoacoustic methodology in the transmission configuration (PMTC) was used to study the thermophysical properties and their relation with the composition in Mexican citrus essential oils providing the viability of using photothermal techniques for quality control and for authentication of oils and their adulteration. Linear relations for the amplitude (on a semi-log scale) and phase, as functions of the sample's thickness, for the PMTC was obtained through a theoretical model fit to the experimental data for thermal-diffusivity measurements in Mexican orange, pink grapefruit, mandarin, lime type A, centrifuged essential oils, and Mexican distilled lime essential oil. Gas chromatography for distilled lime essential oil and centrifuged lime essential oil type A is reported to complement the study. Experimental results showed close thermal-diffusivity values between Mexican citrus essential oils obtained by centrifugation, but a significant difference of this physical property for distilled lime oil and the corresponding value obtained by centrifugation, which is due to their different chemical compositions involved with the extraction processes.

  10. Sampling Criterion for EMC Near Field Measurements

    DEFF Research Database (Denmark)

    Franek, Ondrej; Sørensen, Morten; Ebert, Hans;

    2012-01-01

    An alternative, quasi-empirical sampling criterion for EMC near field measurements intended for close coupling investigations is proposed. The criterion is based on maximum error caused by sub-optimal sampling of near fields in the vicinity of an elementary dipole, which is suggested as a worst......-case representative of a signal trace on a typical printed circuit board. It has been found that the sampling density derived in this way is in fact very similar to that given by the antenna near field sampling theorem, if an error less than 1 dB is required. The principal advantage of the proposed formulation is its...... parametrization with respect to the desired maximum error in measurements. This allows the engineer performing the near field scan to choose a suitable compromise between accuracy and measurement time....

  11. Development of a bio-magnetic measurement system and sensor configuration analysis for rats

    Science.gov (United States)

    Kim, Ji-Eun; Kim, In-Seon; Kim, Kiwoong; Lim, Sanghyun; Kwon, Hyukchan; Kang, Chan Seok; Ahn, San; Yu, Kwon Kyu; Lee, Yong-Ho

    2017-04-01

    Magnetoencephalography (MEG) based on superconducting quantum interference devices enables the measurement of very weak magnetic fields (10-1000 fT) generated from the human or animal brain. In this article, we introduce a small MEG system that we developed specifically for use with rats. Our system has the following characteristics: (1) variable distance between the pick-up coil and outer Dewar bottom (˜5 mm), (2) small pick-up coil (4 mm) for high spatial resolution, (3) good field sensitivity (45 ˜ 80 fT /cm/√{Hz} ) , (4) the sensor interval satisfies the Nyquist spatial sampling theorem, and (5) small source localization error for the region to be investigated. To reduce source localization error, it is necessary to establish an optimal sensor layout. To this end, we simulated confidence volumes at each point on a grid on the surface of a virtual rat head. In this simulation, we used locally fitted spheres as model rat heads. This enabled us to consider more realistic volume currents. We constrained the model such that the dipoles could have only four possible orientations: the x- and y-axes from the original coordinates, and two tangentially layered dipoles (local x- and y-axes) in the locally fitted spheres. We considered the confidence volumes according to the sensor layout and dipole orientation and positions. We then conducted a preliminary test with a 4-channel MEG system prior to manufacturing the multi-channel system. Using the 4-channel MEG system, we measured rat magnetocardiograms. We obtained well defined P-, QRS-, and T-waves in rats with a maximum value of 15 pT/cm. Finally, we measured auditory evoked fields and steady state auditory evoked fields with maximum values 400 fT/cm and 250 fT/cm, respectively.

  12. Measuring sound absorption using local field assumptions

    NARCIS (Netherlands)

    Kuipers, E.R.

    2013-01-01

    To more effectively apply acoustically absorbing materials, it is desirable to measure angle-dependent sound absorption coefficients, preferably in situ. Existing measurement methods are based on an overall model of the acoustic field in front of the absorber, and are therefore sensitive to

  13. Influence of non-aqueous phase liquid configuration on induced polarization parameters: Conceptual models applied to a time-domain field case study

    Science.gov (United States)

    Johansson, Sara; Fiandaca, Gianluca; Dahlin, Torleif

    2015-12-01

    Resistivity and induced polarization (IP) measurements on soil contaminated with non-aqueous phase liquids (NAPLs) show a great variety in results in previous research. Several laboratory studies have suggested that the presence of NAPLs in soil samples generally decrease the magnitude of the IP-effect, while others have indicated the opposite. A number of conceptual models have been proposed suggesting that NAPLs can alter the pore space in different ways, e.g. by coating the grain surfaces and thus inhibiting grain polarization, or by changing the pore throat size and thus affecting the membrane polarization mechanism. The main aim of this paper is to review previously published conceptual models and to introduce some new concepts of possible residual NAPL configurations in the pore space. Time domain induced polarization measurements were performed at a NAPL contaminated field site, and the data were inverted using the Constant Phase Angle (CPA) model and the Cole-Cole model respectively. No significant phase anomalies were observed in the source area of the contamination when the CPA inverted profiles were compared with soil sampling results of free-phase contaminant concentrations. However, relatively strong phase and normalized phase anomalies appeared next to the source area, where residual free-phase presence could be expected according to the chemical data. We conclude that depending on the NAPL configuration, different spectral IP responses can be expected. In previous research, the NAPL configurations in different samples or field sites are often unknown, and this may to some extent explain why different results have been achieved by different authors. In our field case, we believe that the NAPL forms a more or less continuous phase in the pore space of the source zone leading to an absence of IP anomalies. The increase in phase and normalized phase angle observed next to the source zone is interpreted as a degradation zone. The ongoing biodegradation

  14. Experimental results with an optimized magnetic field configuration for JET breakdown

    NARCIS (Netherlands)

    Albanese, R.; Maviglia, F.; Lomas, P. J.; Manzanares, A.; Mattei, M.; Neto, A.; Rimini, F. G.; de Vries, P. C.; JET-EFDA Contributors,

    2012-01-01

    Experiments and modelling have been carried out to optimize the magnetic field null during breakdown at JET. Such optimization may prove to be essential for reliable plasma initiation at low voltages, e.g. in ITER where the value of the electric field available will be limited to 0.33 V&

  15. Field Quality Measurements in the FNAL Twin-Aperture 11 T Dipole for LHC Upgrades

    Energy Technology Data Exchange (ETDEWEB)

    Strauss, T. [Fermilab; Apollinari, G. [Fermilab; Apollinari, G. [Fermilab; Barzi, E. [Fermilab; Chlachidze, G. [Fermilab; Di Marco, J. [Fermilab; Nobrega, F. [Fermilab; Novitski, I. [Fermilab; Stoynev, S. [Fermilab; Turrioni, D. [Fermilab; Velev, G. [Fermilab; Zlobin, A. V. [Fermilab; Auchmann, B. [CERN; Izquierdo Bermudez, S, [CERN; Karppinen, M. [CERN; Rossi, L. [CERN; Savary, F. [CERN; Smekens, D. [CERN

    2016-11-08

    FNAL and CERN are developing an 11 T Nb3Sn dipole suitable for installation in the LHC to provide room for additional collimators. Two 1 m long collared coils previously tested at FNAL in single-aperture dipole configuration were assembled into the twin-aperture configuration and tested including magnet quench performance and field quality. The results of magnetic measurements are reported and discussed in this paper.

  16. Investigation of different magnetic field configurations using an electrical, modular Zeeman slower

    Energy Technology Data Exchange (ETDEWEB)

    Ohayon, Ben; Ron, Guy, E-mail: gron@racah.phys.huji.ac.il [Racah Institute of Physics, Hebrew University of Jerusalem, Jerusalem 91904 (Israel)

    2015-10-15

    We present a method of constructing an automatically reconfigurable, modular, electronic Zeeman slower, which is remotely controlled. This setup is used to investigate the ability of different magnetic field profiles to slow thermal atoms to the capture velocity of a magneto-optical-trap. We show that a simple numerical optimization process yields better results than the commonly used approach for deciding on the appropriate field and comes close to the optimum field, found by utilizing a fast feedback loop which uses a genetic algorithm. Our new numerical method is easily adaptable to a variety of existing slower designs and may be beneficial where feedback is unavailable.

  17. Estimation of soil salinity by using Markov Chain Monte Carlo simulation for multi-configuration electromagnetic induction measurements

    Science.gov (United States)

    Jadoon, K. Z.; Altaf, M. U.; McCabe, M. F.; Hoteit, I.; Moghadas, D.

    2014-12-01

    In arid and semi-arid regions, soil salinity has a major impact on agro-ecosystems, agricultural productivity, environment and sustainability. High levels of soil salinity adversely affect plant growth and productivity, soil and water quality, and may eventually result in soil erosion and land degradation. Being essentially a hazard, it's important to monitor and map soil salinity at an early stage to effectively use soil resources and maintain soil salinity level below the salt tolerance of crops. In this respect, low frequency electromagnetic induction (EMI) systems can be used as a noninvasive method to map the distribution of soil salinity at the field scale and at a high spatial resolution. In this contribution, an EMI system (the CMD Mini-Explorer) is used to estimate soil salinity using a Bayesian approach implemented via a Markov chain Monte Carlo (MCMC) sampling for inversion of multi-configuration EMI measurements. In-situ and EMI measurements were conducted across a farm where Acacia trees are irrigated with brackish water using a drip irrigation system. The electromagnetic forward model is based on the full solution of Maxwell's equation, and the subsurface is considered as a three-layer problem. In total, five parameters (electrical conductivity of three layers and thickness of top two layers) were inverted and modeled electrical conductivities were converted into the universal standard of soil salinity measurement (i.e. using the method of electrical conductivity of a saturated soil paste extract). Simulation results demonstrate that the proposed scheme successfully recovers soil salinity and reduces the uncertainties in the prior estimate. Analysis of the resulting posterior distribution of parameters indicates that electrical conductivity of the top two layers and the thickness of the first layer are well constrained by the EMI measurements. The proposed approach allows for quantitative mapping and monitoring of the spatial electrical conductivity

  18. Plasma grid design for optimized filter field configuration for the NBI test facility ELISE

    Energy Technology Data Exchange (ETDEWEB)

    Nocentini, R. [Max-Planck-Institut fuer Plasmaphysik, EURATOM Association, D-85740 Garching (Germany)], E-mail: riccardo.nocentini@ipp.mpg.de; Gutser, R.; Heinemann, B.; Froeschle, M.; Riedl, R. [Max-Planck-Institut fuer Plasmaphysik, EURATOM Association, D-85740 Garching (Germany)

    2009-12-15

    Maintenance-free RF sources for negative hydrogen ions with moderate extraction areas (100-200 cm{sup 2}) have been successfully developed in the last years at IPP Garching in the test facilities BATMAN and MANITU. A facility with larger extraction area (1000 cm{sup 2}), ELISE, is being designed with a 'half-size' ITER-like extraction system, pulsed ion acceleration up to 60 kV for 10 s and plasma generation up to 1 h. Due to the large size of the source, the magnetic filter field (FF) cannot be produced solely by permanent magnets. Therefore, an additional magnetic field produced by current flowing through the plasma grid (PG current) is required. The filter field homogeneity and the interaction with the electron suppression magnetic field have been studied in detail by finite element method (FEM) during the ELISE design phase. Significant improvements regarding the field homogeneity have been introduced compared to the ITER reference design. Also, for the same PG current a 50% higher field in front of the grid has been achieved by optimizing the plasma grid geometry. Hollow spaces have been introduced in the plasma grid for a more homogeneous PG current distribution. The introduction of hollow spaces also allows the insertion of permanent magnets in the plasma grid.

  19. SCF and CI calculations of the dipole moment function of ozone. [Self-Consistent Field and Configuration-Interaction

    Science.gov (United States)

    Curtiss, L. A.; Langhoff, S. R.; Carney, G. D.

    1979-01-01

    The constant and linear terms in a Taylor series expansion of the dipole moment function of the ground state of ozone are calculated with Cartesian Gaussian basis sets ranging in quality from minimal to double zeta plus polarization. Results are presented at both the self-consistent field and configuration-interaction levels. Although the algebraic signs of the linear dipole moment derivatives are all established to be positive, the absolute magnitudes of these quantities, as well as the infrared intensities calculated from them, vary considerably with the level of theory.

  20. Stratospheric electric field measurements with transmediterranean balloons

    Science.gov (United States)

    de La Morena, B. A.; Alberca, L. F.; Curto, J. J.; Holzworth, R. H.

    1993-01-01

    The horizontal component of the stratospheric electric field was measured using a balloon in the ODISEA Campaign of Transmediterranean Balloon Program. The balloon flew between Trapani (Sicily) and El Arenosillo (Huelva, Spain) along the 39 deg N parallel at a height between 34 and 24 km. The high values found for the field on fair-weather and its quasi-turbulent variation, both in amplitude and direction, are difficult to explain with the classical electric field source. A new source, first described by Holzworth (1989), is considered as possibly causing them.

  1. Orthopedic and interventional applications at low field MRI with horizontally open configuration

    Energy Technology Data Exchange (ETDEWEB)

    Koskinen, S.K.; Parkkola, R.K.; Karhu, J.; Komu, M.E.S.; Kormano, M.J. [Diagnostic Radiology, Turku Univ. Hospital (Finland)

    1997-10-01

    The recently introduced horizontally open configuration imagers allow imaging of knee, hip or shoulder during whole range of motion, which is not possible in conventional MR imagers. Special joint motion devices can be used to provide accurate and reproducible studies. In cervical spine, functional MR imaging may be useful in evaluating alarligament stability in patients with late sequelae of a whiplash injury, and in patients with rheumatoid arthritis who are clinically suspected of having a cervical myelopathy or superior migration of the odontoid process. In shoulder, full range of motion abduction study may be helpful in assessing the supraspinatus tendon impingement. To evaluate patellofemoral malalignment, quadriceps loading is recommended since associated contracting muscles and related soft tissue structures can be evaluated. The position of the femoral head relative to the acetabulum during different positions can be assessed. Open-configuration scanners provide an access to patients during scanning procedure, and therefore permit interventional procedures to be monitored with MRI. Such interventions include aspiration cytology/biopsy and different drainage procedures. (orig.) [Deutsch] Die kuerzlich eingefuehrten bildgebenden Systeme mit horizontal offener Konfiguration ermoeglichen die Darstellung von Knie, Huefte oder Schulter ueber den gesamten Bewegungsbereich, war bisher mit konventionellen MR-Systemen nicht moeglich. Fuer genauere und reproduzierbare Untersuchungen koennen spezielle Gelenkbewegungsgeraete verwendet werden. Bei der Halswirbelsaeule kann die funktionelle NMR-Darstellung im Hinblick auf die Beurteilung der Stabilitaet der Ligamenta alaria bei Patienten mit Spaetfolgen eines Schleudertraumas und bei Patienten mit rheumatoider Arthritis von Nutzen sein, wenn klinisch eine zervikale Myelopathie oder superiore migration des Dens axis vermutet wird. Bei der Schulter kann eine Abduktionsstudie des vollen Bewegungsbereichs bei der Beurteilung

  2. Experimental investigation of microwave interaction with magnetoplasma in miniature multipolar configuration using impedance measurements

    Energy Technology Data Exchange (ETDEWEB)

    Dey, Indranuj, E-mail: indranuj@aees.kyushu-u.ac.jp; Toyoda, Yuji; Yamamoto, Naoji; Nakashima, Hideki [Department of Advanced Energy Engineering Science, Kyushu University, Kasuga 816-8580 (Japan)

    2014-09-15

    A miniature microwave plasma source employing both radial and axial magnetic fields for plasma confinement has been developed for micro-propulsion applications. Plasma is initiated by launching microwaves via a short monopole antenna to circumvent geometrical cutoff limitations. The amplitude and phase of the forward and reflected microwave power is measured to obtain the complex reflection coefficient from which the equivalent impedance of the plasma source is determined. Effect of critical plasma density condition is reflected in the measurements and provides insight into the working of the miniature plasma source. A basic impedance calculation model is developed to help in understanding the experimental observations. From experiment and theory, it is seen that the equivalent impedance magnitude is controlled by the coaxial discharge boundary conditions, and the phase is influenced primarily by the plasma immersed antenna impedance.

  3. Stable anisotropic plasma confinement in magnetic configurations with convex-concave field lines

    Science.gov (United States)

    Tsventoukh, M. M.

    2014-02-01

    It is shown that a combination of the convex and the concave part of a field line provides a strong stabilizing action against convective (flute-interchange) plasma instability (Tsventoukh 2011 Nucl. Fusion 51 112002). This results in internal peaking of the stable plasma pressure profile that is calculated from the collisionless kinetic stability criterion for any magnetic confinement system with combination of mirrors and cusps. Connection of the convex and concave field line parts results in a reduction of the space charge that drives the unstable E × B motion, as there is an opposite direction of the particle drift in a non-uniform field at convex and concave field lines. The pressure peaking arises at the minimum of the second adiabatic invariant J that takes place at the ‘middle’ of a tandem mirror-cusp transverse cross-section. The position of the minimum in J varies with the particle pitch angle that results in a shift of the peaking position depending on plasma anisotropy. This allows one to improve a stable peaked pressure profile at a convex-concave field by changing the plasma anisotropy over the trap cross-section. Examples of such anisotropic distribution functions are found that give an additional substantial enhancement in the maximal central pressure. Furthermore, the shape of new calculated stable profiles has a wide central plasma layer instead of a narrow peak.

  4. Electric Field Quantitative Measurement System and Method

    Science.gov (United States)

    Generazio, Edward R. (Inventor)

    2016-01-01

    A method and system are provided for making a quantitative measurement of an electric field. A plurality of antennas separated from one another by known distances are arrayed in a region that extends in at least one dimension. A voltage difference between at least one selected pair of antennas is measured. Each voltage difference is divided by the known distance associated with the selected pair of antennas corresponding thereto to generate a resulting quantity. The plurality of resulting quantities defined over the region quantitatively describe an electric field therein.

  5. Imaging interferometry to measure surface rotation field

    DEFF Research Database (Denmark)

    Travaillot, Thomas; Dohn, Søren; Boisen, Anja

    2013-01-01

    This paper describes a polarized-light imaging interferometer to measure the rotation field of reflecting surfaces. This setup is based on a homemade prism featuring a birefringence gradient. The arrangement is presented before focusing on the homemade prism and its manufacturing process....... The dependence of the measured optical phase on the rotation of the surface is derived, thus highlighting the key parameters driving the sensitivity. The system’s capabilities are illustrated by imaging the rotation field at the surface of a tip-loaded polymer specimen....

  6. APPLICATION OF MULTILAYER FILM CONFIGURATION TO PROTECT PHOTOMULTIPLIER AGAINST EXTERNAL STATIC MAGNETIC FIELDS

    Directory of Open Access Journals (Sweden)

    A. G. Batische

    2012-01-01

    Full Text Available The effectiveness of the screening constant magnetic field is multi-layered film screens system of NiFe/Cu, formed on the cylindrical housing of photomultiplier tubes, and compared with screen-based steel material – brand 80NHS permalloy. It is shown that the most effective is the screen on the basis of the multilayered film screens, which provide shielding effectiveness value 8–10 in magnetic fields with induction of 0,1–1 mT, and 80–100 – in magnetic fields with induction of 2–4 mT , which is 4–5 times higher than for the screen of the material 80NHS.

  7. Electric field measurements from Halley, Antarctica

    Science.gov (United States)

    Nicoll, Keri; Harrison, R. Giles

    2016-04-01

    Antarctica is a unique location for the study of atmospheric electricity. Not only is it one of the most pollutant free places on Earth, but its proximity to the south magnetic pole means that it is an ideal location to study the effects of solar variability on the atmospheric electric field. This is due to the reduced shielding effect of the geomagnetic field at the poles which leads to a greater flux of incoming Galactic Cosmic Rays (GCRs) as well as an increased probability of energetic particle precipitation from SEPs and relativistic electrons. To investigate such effects, two electric field mills of different design were installed at the British Antarctic Survey Halley base in February 2015 (75. 58 degrees south, 26.66 degrees west). Halley is situated on the Brunt Ice Shelf in the south east of the Weddell Sea and has snow cover all year round. Preliminary analysis has focused on selection of fair weather criteria using wind speed and visibility measurements which are vital to assess the effects of falling snow, blowing snow and freezing fog on the electric field measurements. When the effects of such adverse weather conditions are removed clear evidence of the characteristic Carnegie Curve diurnal cycle exists in the Halley electric field measurements (with a mean value of 50V/m and showing a 40% peak to peak variation in comparison to the 34% variation in the Carnegie data). Since the Carnegie Curve represents the variation in thunderstorm activity across the Earth, its presence in the Halley data confirms the presence of the global atmospheric electric circuit signal at Halley. The work presented here will discuss the details of the Halley electric field dataset, including the variability in the fair weather measurements, with a particular focus on magnetic field fluctuations.

  8. Magnetic sensor for configurable measurement of tension or elasticity with validation in animal soft tissues.

    Science.gov (United States)

    Singal, Kalpesh; Rajamani, Rajesh; Ahmadi, Mahdi; Serdar Sezen, A; Bechtold, Joan E

    2015-02-01

    This paper presents a novel Hall-effect-based magnetic sensor for handheld measurement of either elasticity or tension in soft tissues. A theoretical model is developed for the mechanical interaction of the sensor with the tissue, and conditions are established under which the separate effects of tension or elasticity can be measured. A model of the magnetic field within the sensor is developed and a technique to estimate the sensor response in the presence of multiple magnets is established. This paper then provides analytical sensor responses and compares them with experimental results obtained on synthetic materials. It is found that the sensor can measure tension values upto 100 N with a resolution of 10 N in handheld operation and elasticity of upto 0.87 MPa with a resolution of 0.02 MPa. Significant experimental characterization and statistical analysis of sensor repeatability is performed. The viability of this sensor to make tension and elasticity measurements with biological tissues is then demonstrated using turkey tendons and fresh swine tissues.

  9. Numerical Analysis of Neutral Entrainment Effect on Field-Reversed Configuration Thruster Efficiency

    Science.gov (United States)

    2014-12-01

    efficiently accelerated by the electromagnetic field. On the contrary, the electron impact ionization, being a highly endothermic reaction, takes away...The authors used, in part, the Extreme Science and Engineering Discovery Environment, which is supported by National Science Foundation grant number

  10. Study of the Synchronous Operation of an Annular Field Reversed Configuration Plasma Device

    Science.gov (United States)

    2008-05-05

    coil theta pinch (CSS) [42], multi-pole geometry ( Extrap ) [35], and rotating magnetic field (Rotamak) [24]. In total, developing a lower voltage...orbit-limited current collection. Physics of Fluids, 16(5):629–36, 1973. [35] B. Lehnert. The extrap concept. Nuclear Instruments and Methods in

  11. Magnetic Linear Birefringence Measurements Using Pulsed Fields

    CERN Document Server

    Berceau, Paul; Battesti, Remy; Rizzo, Carlo

    2011-01-01

    In this paper we present the accomplishment of the further step towards the vacuum magnetic birefringence measurement based on pulsed fields. After describing our BMV experiment, we report the calibration of our apparatus with nitrogen gas and we discuss the precision of our measurement giving a detailed error budget. Our best present vacuum sensitivity is 2.1x 10^-19 T^-2 per 5 ms magnetic pulse. We finally discuss the perspectives to reach our final goal.

  12. Configuration mixing of mean-field wave-functions projected on angular momentum and particle number; application to 24Mg

    CERN Document Server

    Valor, A; Bonche, P

    2000-01-01

    We present in this paper the general framework of a method which permits to restore the rotational and particle number symmetries of wave functions obtained in Skyrme HF+BCS calculations. This restoration is nothing but a projection of mean-field intrinsic wave functions onto good particle number and good angular momentum. The method allows also to mix projected wave functions. Such a configuration mixing is discussed for sets of HF+BCS intrinsic states generated in constrained calculations with suitable collective variables. This procedure gives collective states which are eigenstates of the particle number and the angular momentum operators and between which transition probabilities are calculated. An application to 24Mg is presented, with mean-field wave functions generated by axial quadrupole constraints. Theoretical spectra and transition probabilities are compared to the experiment.

  13. Assessment of gravity wave momentum flux measurement capabilities by meteor radars having different transmitter power and antenna configurations

    Science.gov (United States)

    Fritts, D. C.; Janches, D.; Hocking, W. K.; Mitchell, N. J.; Taylor, M. J.

    2012-05-01

    Measurement capabilities of five meteor radars are assessed and compared to determine how well radars having different transmitted power and antenna configurations perform in defining mean winds, tidal amplitudes, and gravity wave (GW) momentum fluxes. The five radars include two new-generation meteor radars on Tierra del Fuego, Argentina (53.8°S) and on King George Island in the Antarctic (62.1°S) and conventional meteor radars at Socorro, New Mexico (34.1°N, 106.9°W), Bear Lake Observatory, Utah (˜41.9°N, 111.4°W), and Yellowknife, Canada (62.5°N, 114.3°W). Our assessment employs observed meteor distributions for June of 2009, 2010, or 2011 for each radar and a set of seven test motion fields including various superpositions of mean winds, constant diurnal tides, constant and variable semidiurnal tides, and superposed GWs having various amplitudes, scales, periods, directions of propagation, momentum fluxes, and intermittencies. Radars having higher power and/or antenna patterns yielding higher meteor counts at small zenith angles perform well in defining monthly and daily mean winds, tidal amplitudes, and GW momentum fluxes, though with expected larger uncertainties in the daily estimates. Conventional radars having lower power and a single transmitting antenna are able to describe monthly mean winds and tidal amplitudes reasonably well, especially at altitudes having the highest meteor counts. They also provide reasonable estimates of GW momentum fluxes at the altitudes having the highest meteor counts; however, these estimates are subject to uncertainties of ˜20 to 50% and uncertainties rapidly become excessive at higher and lower altitudes. Estimates of all quantities degrade somewhat for more complex motion fields.

  14. Local electric field measurements by optical tweezers

    Directory of Open Access Journals (Sweden)

    G. Pesce

    2011-09-01

    Full Text Available We report a new technique to measure direction and amplitude of electric fields generated by microelectrodes embedded in polar liquid environment, as often used in microfluidic devices. The method is based on optical tweezers which act as sensitive force transducer while a trapped charged microsphere behaves as a probe. When an electric field is applied the particles moves from its equilibrium position and finishes in a new equilibrium position where electric and optical forces are balanced. A trapped bead is moved to explore the electric field in a wide region around the microelectrodes. In such way maps of electric fields with high spatial resolution can be reconstructed even for complex electrode geometries where numerical simulation approaches can fail. Experimental results are compared with calculations based on finite element analysis simulation.

  15. Steady-state configurations of Dzyaloshinskii domain walls driven by field and current

    Science.gov (United States)

    Sánchez-Tejerina, L.; Alejos, O.; Martínez, E.

    2017-02-01

    The dynamics of Dzyaloshinskii domain walls (DDW) in ultrathin ferromagnetic strips with perpendicular magnetic anisotropy, for different values of both perpendicular field and longitudinal current excitation associated to the Spin-Hall effect, has been studied, taking into account different values of the interfacial Dzyaloshinskii-Moriya interaction (DMI). This study has been carried out with the help of the q-Φ one-dimensional model and micromagnetic simulations. We have found that Walker breakdown may be avoided by applying a certain threshold current, even though the inverse effect is also possible. We have also found that, for particular values of field and current, the magnetization within the DDW experiences an abrupt change of orientation, which provokes a change on the contribution of current to the terminal DDW velocity. This effect disappears for sufficiently strong DMI, as it is expected from the model.

  16. Dosimeter configurations for the measurement of Hs(0.07) and Hp(10) from photons

    DEFF Research Database (Denmark)

    Christensen, P.; Bøtter-Jensen, L.; Ennow, K.

    1990-01-01

    The optimisation is discussed of filter/detector configurations of dosemeters for individual monitoring for photons in the energy range from 20 keV to 1.3 MeV. Experimental data are given on energy and angular responses of dosemeters with different combinations of aluminium and plastic filters. Li...

  17. Lorentz force electrical impedance tomography using magnetic field measurements.

    Science.gov (United States)

    Zengin, Reyhan; Gençer, Nevzat Güneri

    2016-08-21

    In this study, magnetic field measurement technique is investigated to image the electrical conductivity properties of biological tissues using Lorentz forces. This technique is based on electrical current induction using ultrasound together with an applied static magnetic field. The magnetic field intensity generated due to induced currents is measured using two coil configurations, namely, a rectangular loop coil and a novel xy coil pair. A time-varying voltage is picked-up and recorded while the acoustic wave propagates along its path. The forward problem of this imaging modality is defined as calculation of the pick-up voltages due to a given acoustic excitation and known body properties. Firstly, the feasibility of the proposed technique is investigated analytically. The basic field equations governing the behaviour of time-varying electromagnetic fields are presented. Secondly, the general formulation of the partial differential equations for the scalar and magnetic vector potentials are derived. To investigate the feasibility of this technique, numerical studies are conducted using a finite element method based software. To sense the pick-up voltages a novel coil configuration (xy coil pairs) is proposed. Two-dimensional numerical geometry with a 16-element linear phased array (LPA) ultrasonic transducer (1 MHz) and a conductive body (breast fat) with five tumorous tissues is modeled. The static magnetic field is assumed to be 4 Tesla. To understand the performance of the imaging system, the sensitivity matrix is analyzed. The sensitivity matrix is obtained for two different locations of LPA transducer with eleven steering angles from [Formula: see text] to [Formula: see text] at intervals of [Formula: see text]. The characteristics of the imaging system are shown with the singular value decomposition (SVD) of the sensitivity matrix. The images are reconstructed with the truncated SVD algorithm. The signal-to-noise ratio in measurements is assumed 80 d

  18. Lorentz force electrical impedance tomography using magnetic field measurements

    Science.gov (United States)

    Zengin, Reyhan; Güneri Gençer, Nevzat

    2016-08-01

    In this study, magnetic field measurement technique is investigated to image the electrical conductivity properties of biological tissues using Lorentz forces. This technique is based on electrical current induction using ultrasound together with an applied static magnetic field. The magnetic field intensity generated due to induced currents is measured using two coil configurations, namely, a rectangular loop coil and a novel xy coil pair. A time-varying voltage is picked-up and recorded while the acoustic wave propagates along its path. The forward problem of this imaging modality is defined as calculation of the pick-up voltages due to a given acoustic excitation and known body properties. Firstly, the feasibility of the proposed technique is investigated analytically. The basic field equations governing the behaviour of time-varying electromagnetic fields are presented. Secondly, the general formulation of the partial differential equations for the scalar and magnetic vector potentials are derived. To investigate the feasibility of this technique, numerical studies are conducted using a finite element method based software. To sense the pick-up voltages a novel coil configuration (xy coil pairs) is proposed. Two-dimensional numerical geometry with a 16-element linear phased array (LPA) ultrasonic transducer (1 MHz) and a conductive body (breast fat) with five tumorous tissues is modeled. The static magnetic field is assumed to be 4 Tesla. To understand the performance of the imaging system, the sensitivity matrix is analyzed. The sensitivity matrix is obtained for two different locations of LPA transducer with eleven steering angles from -{{25}\\circ} to {{25}\\circ} at intervals of {{5}\\circ} . The characteristics of the imaging system are shown with the singular value decomposition (SVD) of the sensitivity matrix. The images are reconstructed with the truncated SVD algorithm. The signal-to-noise ratio in measurements is assumed 80 dB. Simulation studies

  19. Electric Field Effects in RUS Measurements

    Energy Technology Data Exchange (ETDEWEB)

    Darling, Timothy W [Los Alamos National Laboratory; Ten Cate, James A [Los Alamos National Laboratory; Allured, Bradley [UNIV NEVADA, RENO; Carpenter, Michael A [CAMBRIDGE UNIV. UK

    2009-09-21

    Much of the power of the Resonant Ultrasound Spectroscopy (RUS) technique is the ability to make mechanical resonance measurements while the environment of the sample is changed. Temperature and magnetic field are important examples. Due to the common use of piezoelectric transducers near the sample, applied electric fields introduce complications, but many materials have technologically interesting responses to applied static and RF electric fields. Non-contact optical, buffered, or shielded transducers permit the application of charge and externally applied electric fields while making RUS measurements. For conducting samples, in vacuum, charging produces a small negative pressure in the volume of the material - a state rarely explored. At very high charges we influence the electron density near the surface so the propagation of surface waves and their resonances may give us a handle on the relationship of electron density to bond strength and elasticity. Our preliminary results indicate a charge sign dependent effect, but we are studying a number of possible other effects induced by charging. In dielectric materials, external electric fields influence the strain response, particularly in ferroelectrics. Experiments to study this connection at phase transformations are planned. The fact that many geological samples contain single crystal quartz suggests a possible use of the piezoelectric response to drive vibrations using applied RF fields. In polycrystals, averaging of strains in randomly oriented crystals implies using the 'statistical residual' strain as the drive. The ability to excite vibrations in quartzite polycrystals and arenites is explored. We present results of experimental and theoretical approaches to electric field effects using RUS methods.

  20. Control of ion gyroscale fluctuations via electrostatic biasing and sheared E×B flow in the C-2 field reversed configuration

    Science.gov (United States)

    Schmitz, L.; Ruskov, E.; Deng, B. H.; Binderbauer, M.; Tajima, T.; Gota, H.; Tuszewski, M.

    2016-03-01

    Control of radial particle and thermal transport is instrumental for achieving and sustaining well-confined high-β plasma in a Field-Reversed Configuration (FRC). Radial profiles of low frequency ion gyro-scale density fluctuations (0.5≤kρs≤40), consistent with drift- or drift-interchange modes, have been measured in the scrape-off layer (SOL) and core of the C-2 Field-Reversed Configuration (FRC), together with the toroidal E×B velocity. It is shown here that axial electrostatic SOL biasing controls and reduces gyro-scale density fluctuations, resulting in very low FRC core fluctuation levels. When the radial E×B flow shearing rate decreases below the turbulence decorrelation rate, fluctuation levels increase substantially, concomitantly with onset of the n=2 instability and rapid loss of diamagnetism. Low turbulence levels, improved energy/particle confinement and substantially increased FRC life times are achieved when E×B shear near the separatrix is maintained via axial SOL biasing using an annular washer gun.

  1. Configurational coordinate diagram of Ni{sup 2+} doped silver halide crystals, as determined by optical and luminescence measurements

    Energy Technology Data Exchange (ETDEWEB)

    Zakosky-Neuberger, I., E-mail: yifat_z2@hotmail.com [Raymond and Beverly Sackler Faculty of Exact Sciences, School of Physics and Astronomy, Tel-Aviv University, Tel-Aviv 69978 (Israel); Shafir, I.; Nagli, L.; Katzir, A. [Raymond and Beverly Sackler Faculty of Exact Sciences, School of Physics and Astronomy, Tel-Aviv University, Tel-Aviv 69978 (Israel)

    2012-08-15

    Optical and luminescence measurements were carried out on Ni{sup 2+} doped silver halide crystals. The configurational coordinates of the ground and the first excited states made it possible to explain the important optical properties, such as the Stokes shift between the ground and excited states, the broadening of the bands with temperature and the thermal quenching. Determining the configurational coordinate diagram of the ground and first excited states is the first step for the design and fabrication of solid state and fiber lasers which are based on Ni{sup 2+} doped silver halides and which operate in the middle infrared. - Highlights: Black-Right-Pointing-Pointer Optical and luminescence measurements were carried out on Ni{sup 2+} doped silver halide crystals. Black-Right-Pointing-Pointer Configurational coordinates of the ground and the first excited state were calculated. Black-Right-Pointing-Pointer Optical properties of Ni{sup 2+} doped silver halide crystals can be obtained from the configurational coordinate diagram. Black-Right-Pointing-Pointer No emission signal was found above 220 K.

  2. Performance test of dual modulator polarimeters in two different configurations for magneto-optic measurement of fusion devices

    Energy Technology Data Exchange (ETDEWEB)

    Higuchi, Kenji [Tokyo Institute of Technology, 2-12-1 O-okayama, Meguro-ku, Tokyo 152-8550 (Japan)], E-mail: 05m19220@nr.titech.ac.jp; Akiyama, Tsuyoshi [National Institute for Fusion Science, 322-6 Oroshi-cho, Toki-shi, Gifu 509-5292 (Japan); Azuma, Yoshifumi; Tsuji-Iio, Shunji; Tsutsui, Hiroaki; Shimada, Ryuichi [Tokyo Institute of Technology, 2-12-1 O-okayama, Meguro-ku, Tokyo 152-8550 (Japan)

    2007-10-15

    We proposed and tested a new configuration of a magneto-optic polarimeter with a pair of photoelastic modulators (PEMs). In the new configuration, the number of optical components including PEMs can be much smaller than that in a conventional one with PEMs. This paper describes the results of performance test and comparisons to the conventional configuration. The dependences on the light source (a He-Ne laser, 632.8 nm and a superluminescent diode, SLD, 822 nm) are also discussed. The polarization angle can be measured and angle resolution comparable to those in the conventional one was obtained. Angle resolution of 0.002 deg. and 0.07 deg. with a response time of 10 ms was achieved at an incident polarization angle of about 0 deg. and 21 deg., respectively. The resolution of 0.07 deg. corresponds to 7 G when a 40-mm-long ZnSe sensing rod is used. Linearity of the measured angle against the real one degraded, especially with He-Ne laser, increasing the numbers of the mirrors for beam transmission. On the other hand, the resolution is insensitive to the number of mirrors. Good long-time stability was confirmed with the SLD but a little deterioration was found with the He-Ne laser in the two configurations.

  3. What are the Confining Field Configurations of Strong-Coupling Lattice Gauge Theory?

    CERN Document Server

    Faber, M; Olejník, S

    2000-01-01

    Starting from the strong-coupling SU(2) Wilson action in D=3 dimensions, we derive an effective, semi-local action on a lattice of spacing L times the spacing of the original lattice. It is shown that beyond the adjoint color-screening distance, i.e. for $L \\ge 5$, thin center vortices are stable saddlepoints of the corresponding effective action. Since the entropy of these stable objects exceeds their energy, center vortices percolate throughout the lattice, and confine color charge in half-integer representations of the SU(2) gauge group. This result contradicts the folklore that confinement in strong-coupling lattice gauge theory, for D>2 dimensions, is simply due to plaquette disorder, as is the case in D=2 dimensions. It also demonstrates explicitly how the emergence and stability of center vortices is related to the existence of color screening by gluon fields.

  4. Onset of a Large Ejective Solar Eruption from a Typical Coronal-jet-base Field Configuration

    Science.gov (United States)

    Joshi, Navin Chandra; Sterling, Alphonse C.; Moore, Ronald L.; Magara, Tetsuya; Moon, Young-Jae

    2017-08-01

    Utilizing multiwavelength observations and magnetic field data from the Solar Dynamics Observatory (SDO)/Atmospheric Imaging Assembly (AIA), SDO/Helioseismic and Magnetic Imager (HMI), the Geostationary Operational Environmental Satellite (GOES), and RHESSI, we investigate a large-scale ejective solar eruption of 2014 December 18 from active region NOAA 12241. This event produced a distinctive “three-ribbon” flare, having two parallel ribbons corresponding to the ribbons of a standard two-ribbon flare, and a larger-scale third quasi-circular ribbon offset from the other two. There are two components to this eruptive event. First, a flux rope forms above a strong-field polarity inversion line and erupts and grows as the parallel ribbons turn on, grow, and spread apart from that polarity inversion line; this evolution is consistent with the mechanism of tether-cutting reconnection for eruptions. Second, the eruption of the arcade that has the erupting flux rope in its core undergoes magnetic reconnection at the null point of a fan dome that envelops the erupting arcade, resulting in formation of the quasi-circular ribbon; this is consistent with the breakout reconnection mechanism for eruptions. We find that the parallel ribbons begin well before (˜12 minutes) the onset of the circular ribbon, indicating that tether-cutting reconnection (or a non-ideal MHD instability) initiated this event, rather than breakout reconnection. The overall setup for this large-scale eruption (diameter of the circular ribbon ˜105 km) is analogous to that of coronal jets (base size ˜104 km), many of which, according to recent findings, result from eruptions of small-scale “minifilaments.” Thus these findings confirm that eruptions of sheared-core magnetic arcades seated in fan-spine null-point magnetic topology happen on a wide range of size scales on the Sun.

  5. High-k ZrO2/Al2O3 bilayer on hydrogenated diamond: Band configuration, breakdown field, and electrical properties of field-effect transistors

    Science.gov (United States)

    Liu, J. W.; Liao, M. Y.; Imura, M.; Koide, Y.

    2016-09-01

    A band configuration of a high-k ZrO2/Al2O3 bilayer on hydrogenated diamond (H-diamond), a breakdown field (EB) of the ZrO2/Al2O3 bilayer, and an effect of gate-drain distance (dG-D) on electrical properties of ZrO2/Al2O3/H-diamond metal-insulator-semiconductor field-effect transistors (MISFETs) have been investigated. The Al2O3 and ZrO2 layers are successively deposited on H-diamond by atomic layer deposition (ALD) and sputtering-deposition (SD) techniques, respectively. The thin ALD-Al2O3 buffer layer with 4.0 nm thickness plays a role in protecting the H-diamond surface from being damaged by the plasma discharge during SD-ZrO2 deposition. The ZrO2/Al2O3 heterojunction has a type I band structure with valence and conduction band offsets of 0.6 ± 0.2 and 1.0 ± 0.2 eV, respectively. The valence band offset between ZrO2 and H-diamond is deduced to be 2.3 ± 0.2 eV. The EB of the ZrO2/Al2O3 bilayer is measured to be 5.2 MV cm-1, which is larger than that of the single ZrO2 layer due to the existence of the ALD-Al2O3 buffer layer. The dependence of dG-D on drain-source current maximum (IDS,max), on-resistance (RON), threshold voltage (VTH), and extrinsic transconductance maximum (gm,max) of the MISFETs has been investigated. With increasing dG-D from 4 to 18 μm, the absolute IDS,max decreases from 72.7 to 40.1 mA mm-1, and the RON increases linearly from 83.3 ± 5 to 158.7 ± 5 Ω mm. Variation of VTH values of around 1.0 V is observed, and the gm,max is in the range between 8.0 ± 0.1 and 13.1 ± 0.1 mS mm-1.

  6. Measuring Propagation Speed of Coulomb Fields

    CERN Document Server

    Calcaterra, A; Finocchiaro, G; Patteri, P; Piccolo, M; Pizzella, G

    2012-01-01

    The problem of gravity propagation has been subject of discussion for quite a long time: Newton, Laplace and, in relatively more modern times, Eddington pointed out that, if gravity propagated with finite velocity, planets motion around the sun would become unstable due to a torque originating from time lag of the gravitational interactions. Such an odd behavior can be found also in electromagnetism, when one computes the propagation of the electric fields generated by a set of uniformly moving charges. As a matter of fact the Li\\'enard-Weichert retarded potential leads to a formula indistinguishable from the one obtained assuming that the electric field propagates with infinite velocity. Feyman explanation for this apparent paradox was based on the fact that uniform motions last indefinitely. To verify such an explanation, we performed an experiment to measure the time/space evolution of the electric field generated by an uniformely moving electron beam. The results we obtain on such a finite lifetime kinema...

  7. A high power impulse magnetron sputtering model to explain high deposition rate magnetic field configurations

    Science.gov (United States)

    Raman, Priya; Weberski, Justin; Cheng, Matthew; Shchelkanov, Ivan; Ruzic, David N.

    2016-10-01

    High Power Impulse Magnetron Sputtering (HiPIMS) is one of the recent developments in the field of magnetron sputtering technology that is capable of producing high performance, high quality thin films. Commercial implementation of HiPIMS technology has been a huge challenge due to its lower deposition rates compared to direct current Magnetron Sputtering. The cylindrically symmetric "TriPack" magnet pack for a 10 cm sputter magnetron that was developed at the Center for Plasma Material Interactions was able to produce higher deposition rates in HiPIMS compared to conventional pack HiPIMS for the same average power. The "TriPack" magnet pack in HiPIMS produces superior substrate uniformity without the need of substrate rotation in addition to producing higher metal ion fraction to the substrate when compared to the conventional pack HiPIMS [Raman et al., Surf. Coat. Technol. 293, 10 (2016)]. The films that are deposited using the "TriPack" magnet pack have much smaller grains compared to conventional pack DC and HiPIMS films. In this paper, the reasons behind the observed increase in HiPIMS deposition rates from the TriPack magnet pack along with a modified particle flux model is discussed.

  8. Feasibility study of microwave electron heating on the C-2 field-reversed configuration device

    Energy Technology Data Exchange (ETDEWEB)

    Yang, Xiaokang, E-mail: xyang@trialphaenergy.com; Ceccherini, Francesco; Dettrick, Sean; Binderbauer, Michl [Tri Alpha Energy, Inc., P.O. Box 7010, Rancho Santa Margarita, CA 92688 (United States); Koehn, Alf [IGVP, University of Stuttgart, Pfaffenwaldring 31, 70569 Stuttgart (Germany); Petrov, Yuri [CompX, P.O. Box 2672, Del Mar, CA 92014 (United States)

    2015-12-10

    Different microwave heating scenarios for the C-2 plasmas have been investigated recently with use of both the Genray ray-racing code and the IPF-FDMC full-wave code, and the study was focused on the excitation of the electron Bernstein wave (EBW) with O-mode launch. For a given antenna position on C-2 and the fixed 2D plasma density and equilibrium field profiles, simulations have been done for six selected frequencies (2.45 GHz, 5 GHz, 8 GHz, 18 GHz, 28 GHz, and 50 GHz). Launch angles have been optimized for each case in order to achieve high coupling efficiencies to the EBW by the O-X-B mode conversion process and high power deposition. Results show that among those six frequencies, the case of 8 GHz is the most promising scenario, which has both high mode conversion efficiency (90%) and the relatively deeper power deposition.

  9. Measurement of the ATLAS solenoid magnetic field

    CERN Document Server

    Aleksa, M; Giudici, P-A; Kehrli, A; Losasso, M; Pons, X; Sandaker, H; Miyagawa, P S; Snow, S W; Hart, J C; Chevalier, L

    2008-01-01

    ATLAS is a general purpose detector designed to explore a wide range of physics at the Large Hadron Collider. At the centre of ATLAS is a tracking detector in a 2 T solenoidal magnetic field. This paper describes the machine built to map the field, the data analysis methods, the final results, and their estimated uncertainties. The remotely controlled mapping machine used pneumatic motors with feedback from optical encoders to scan an array of Hall probes over the field volume and log data at more than 20 000 points in a few hours. The data were analysed, making full use of the physical constraints on the field and of our knowledge of the solenoid coil geometry. After a series of small corrections derived from the data itself, the resulting maps were fitted with a function obeying Maxwell's equations. The fit residuals had an r.m.s. less than 0.5 mT and the systematic error on the measurement of track sagitta due to the field uncertainty was estimated to be in the range 0.02 % to 0.12 % depending on the track...

  10. Strong-field ionization rates of linear polyenes simulated with time-dependent configuration interaction with an absorbing potential

    Science.gov (United States)

    Krause, Pascal; Schlegel, H. Bernhard

    2014-11-01

    The strong field ionization rates for ethylene, trans 1,3-butadiene, and trans,trans 1,3,5-hexatriene have been calculated using time-dependent configuration interaction with single excitations and a complex absorbing potential (TDCIS-CAP). The calculations used the aug-cc-pVTZ basis set with a large set of diffuse functions (3 s, 2 p, 3 d, and 1 f) on each atom. The absorbing boundary was placed 3.5 times the van der Waals radius from each atom. The simulations employed a seven-cycle cosine squared pulse with a wavelength of 800 nm. Ionization rates were calculated for intensities ranging from 0.3 × 1014 W/cm2 to 3.5 × 1014 W/cm2. Ionization rates along the molecular axis increased markedly with increasing conjugation length. By contrast, ionization rates perpendicular to the molecular axis were almost independent of the conjugation length.

  11. CFD prediction of the near-field sonic boom environment for two low boom HSCT configurations. [High Speed Civil Transport

    Science.gov (United States)

    Siclari, M. J.; Darden, C. M.

    1991-01-01

    Current efforts to reduce the sonic boom of a future High Speed Civil Transport (HSCT) by careful shaping have led to the need for more accurate predictions of the near-field flow conditions of the configuration. A fully three-dimensional Euler finite volume code is used to predict sonic boom pressure signatures for two low boom concepts - one designed to cruise at Mach 2 and the other at Mach 3. Calculations were carried out using a grid topology that has been modified to reduce the inaccuracies caused by grid spreading often suffered with CFD methods when calculations several body lengths downstream become necessary. Comparisons of CFD results and experimental wind tunnel signatures are shown. Ground signatures are predicted by extrapolating the pressures predicted by the Euler code with an extrapolation method based on the Whitham theory.

  12. Numerical Simulation of Fibre Suspension Flow through an Axisymmetric Contraction and Expansion Passages by Brownian Configuration Field Method

    CERN Document Server

    Lu, Zhumin; Dou, Hua-Shu; Phan-Thien, Nhan; Yeo, Khoon Seng

    2008-01-01

    In this paper, the finite element method is combined with the Brownian Configuration Field (BFC) method to simulate the fibre suspension flow in axisymmetric contraction and expansion passages. In order to solve for the high stress at high concentration, the Discrete Adaptive Viscoelastic Stress Splitting (DAVSS) method is employed. For the axisymmetric contraction and expansion passages with different geometry ratios, the results obtained are compared to available constitutive models and experiments. The predicted vortex length for dilute suspensions agrees well with experimental data in literature. Our numerical results show clearly the effect on vortex enhancement with increase of the volume fractions and the aspect ratios. Effect of aspect ratio of fibres on the vortex length is also studied. It is found that for the lower expansion ratio flows the vortex dimension in the corner region is fairly independent of fibre concentration and aspect ratio of fibres while the said vortex dimension increases with th...

  13. Analytic gradients for Mukherjee's multireference coupled-cluster method using two-configurational self-consistent-field orbitals

    Science.gov (United States)

    Jagau, Thomas-C.; Prochnow, Eric; Evangelista, Francesco A.; Gauss, Jürgen

    2010-04-01

    Analytic gradients for the state-specific multireference coupled-cluster method suggested by Mahapatra et al. [Mol. Phys. 94, 157 (1998)] (Mk-MRCC) are reported within the singles and doubles approximation using two-configurational self-consistent field (TCSCF) orbitals. The present implementation extends our previous work on Mk-MRCC gradients [E. Prochnow et al., J. Chem. Phys. 131, 064109 (2009)] which is based on restricted Hartree-Fock orbitals and consequently the main focus of the present paper is on the treatment of orbital relaxation at the TCSCF level using coupled-perturbed TCSCF theory. Geometry optimizations on m-arynes and nitrenes are presented to illustrate the influence of the orbitals on the computed equilibrium structures. The results are compared to those obtained at the single-reference coupled-cluster singles and doubles and at the Mk-MRCC singles and doubles level of theory when using restricted Hartree-Fock orbitals.

  14. Boom accomodation effects on plasma and field measurements with RPWI

    Science.gov (United States)

    Cervantes Correa, P.; Eriksson, A. I.; Wahlund, J.-E.; Odelstad, E.; Vaivads, A.; Bergman, J.

    2013-09-01

    While the JUICE spacecraft configuration and main contractor are yet to be decided, it is still possible to investigate general issues on the impact of various boom accomodation alternatives for measurements of plasma and electric fields using the Langmuir probe system of the Radio and Plasma Waves Investigation. These probes can be used as classical Langmuir probes, as electric field probes, or for mutual impedance measurements, and the impact of e.g. varying illumination and wake interference are different for each type of measurement. While there is a nominal JUICE trajectory for the main science mission, we have to do assumptions on the spacecraft pointing, e.g. nadir pointing during flybys of the various moons. The detailed spacecraft layout is not known, but we can arrive at general conclusions on the suitability of various boom accomodations by assuming a cube-like spacecraft with solar panels as rectangular wings. For disturbing structures like wakes and photoelectron clouds we use simple models based on previous simulations. Even though the detailed pointing and spacecraft design will quite certainly deviate from our assumptions, and the model has uncertainties also in other respects, we can still give some general conclusions on boom accomodation alternatives.

  15. Dual wavelength imaging of a scrape-off layer in an advanced beam-driven field-reversed configuration

    Science.gov (United States)

    Osin, D.; Schindler, T.

    2016-11-01

    A dual wavelength imaging system has been developed and installed on C-2U to capture 2D images of a He jet in the Scrape-Off Layer (SOL) of an advanced beam-driven Field-Reversed Configuration (FRC) plasma. The system was designed to optically split two identical images and pass them through 1 nm FWHM filters. Dual wavelength images are focused adjacent on a large format CCD chip and recorded simultaneously with a time resolution down to 10 μs using a gated micro-channel plate. The relatively compact optical system images a 10 cm plasma region with a spatial resolution of 0.2 cm and can be used in a harsh environment with high electro-magnetic noise and high magnetic field. The dual wavelength imaging system provides 2D images of either electron density or temperature by observing spectral line pairs emitted by He jet atoms in the SOL. A large field of view, combined with good space and time resolution of the imaging system, allows visualization of macro-flows in the SOL. First 2D images of the electron density and temperature observed in the SOL of the C-2U FRC are presented.

  16. Dual wavelength imaging of a scrape-off layer in an advanced beam-driven field-reversed configuration

    Energy Technology Data Exchange (ETDEWEB)

    Osin, D.; Schindler, T., E-mail: dosin@trialphaenergy.com [Tri Alpha Energy, Inc., P.O. Box 7010, Rancho Santa Margarita, California 92688-7010 (United States)

    2016-11-15

    A dual wavelength imaging system has been developed and installed on C-2U to capture 2D images of a He jet in the Scrape-Off Layer (SOL) of an advanced beam-driven Field-Reversed Configuration (FRC) plasma. The system was designed to optically split two identical images and pass them through 1 nm FWHM filters. Dual wavelength images are focused adjacent on a large format CCD chip and recorded simultaneously with a time resolution down to 10 μs using a gated micro-channel plate. The relatively compact optical system images a 10 cm plasma region with a spatial resolution of 0.2 cm and can be used in a harsh environment with high electro-magnetic noise and high magnetic field. The dual wavelength imaging system provides 2D images of either electron density or temperature by observing spectral line pairs emitted by He jet atoms in the SOL. A large field of view, combined with good space and time resolution of the imaging system, allows visualization of macro-flows in the SOL. First 2D images of the electron density and temperature observed in the SOL of the C-2U FRC are presented.

  17. Measurements of Photospheric and Chromospheric Magnetic Fields

    Science.gov (United States)

    Lagg, Andreas; Lites, Bruce; Harvey, Jack; Gosain, Sanjay; Centeno, Rebecca

    2017-09-01

    The Sun is replete with magnetic fields, with sunspots, pores and plage regions being their most prominent representatives on the solar surface. But even far away from these active regions, magnetic fields are ubiquitous. To a large extent, their importance for the thermodynamics in the solar photosphere is determined by the total magnetic flux. Whereas in low-flux quiet Sun regions, magnetic structures are shuffled around by the motion of granules, the high-flux areas like sunspots or pores effectively suppress convection, leading to a temperature decrease of up to 3000 K. The importance of magnetic fields to the conditions in higher atmospheric layers, the chromosphere and corona, is indisputable. Magnetic fields in both active and quiet regions are the main coupling agent between the outer layers of the solar atmosphere, and are therefore not only involved in the structuring of these layers, but also for the transport of energy from the solar surface through the corona to the interplanetary space. Consequently, inference of magnetic fields in the photosphere, and especially in the chromosphere, is crucial to deepen our understanding not only for solar phenomena such as chromospheric and coronal heating, flares or coronal mass ejections, but also for fundamental physical topics like dynamo theory or atomic physics. In this review, we present an overview of significant advances during the last decades in measurement techniques, analysis methods, and the availability of observatories, together with some selected results. We discuss the problems of determining magnetic fields at smallest spatial scales, connected with increasing demands on polarimetric sensitivity and temporal resolution, and highlight some promising future developments for their solution.

  18. Global non-axisymmetric perturbation configurations in a composite disc system with an isopedic magnetic field: relation between dark matter halo and magnetic field

    CERN Document Server

    Xiang-Gruess, M; Duschl, W J

    2009-01-01

    We study global non-axisymmetric stationary perturbations of aligned and unaligned logarithmic spiral configurations in an axisymmetric composite differentially rotating disc system of scale-free stellar and isopedically magnetized gas discs coupled by gravity. The gas disc is threaded across by a vertical magnetic field $B_z$ with a constant dimensionless isopedic ratio $\\lambda\\equiv 2\\pi\\sqrt{G} \\Sigma^{(g)}/B_z$ of surface gas mass density $\\Sigma^{(g)}$ to $B_z$ with $G$ being the gravitational constant. Our exploration focuses on the relation between $\\lambda$ and the dark matter amount represented by a ratio $f\\equiv\\bar{\\Phi}/\\Phi$ in order to sustain stationary perturbation configurations, where $\\bar{\\Phi}$ is the gravitational potential of a presumed axisymmetric halo of dark matter and $\\Phi$ is the gravitational potential of the composite disc matter. High and low $\\lambda$ values correspond to relatively weak and strong magnetic fields given the same gas surface mass density, respectively. The m...

  19. Buckling measurement in the IPEN/MB-01 nuclear reactor in cylindrical configuration of minor excess of reactivity

    Energy Technology Data Exchange (ETDEWEB)

    Purgato, Rafael Turrini; Bitelli, Ulysses d' Utra; Aredes, Vitor Ottoni; Silva, Alexandre F. Povoa da; Santos, Diogo Feliciano dos; Lima, Ana Cecilia de Souza, E-mail: ubitelli@ipen.br [Instituto de Pesquisas Energeticas e Nucleares (IPEN/CNEN-SP), Sao Paulo, SP (Brazil)

    2015-07-01

    This work presents the results of experimental Buckling in the IPEN/MB-01 nuclear reactor in its cylindrical configuration with 28 fuel rods along its diameter. The IPEN/MB-01 is a zero power reactor designed to operate at a maximum power of 100 watts. It is a versatile nuclear facility, which allows for the simulation of all the characteristics of a nuclear power reactor making it an ideal test bed for this kind of measurement. A mapping of neutron flux inside the reactor is carried out in order to determine the total Buckling of the cylindrical configuration. The reactor was operated for one hour. Then, the activity of the fuel rods is measured by gamma ray spectrometry using a HPGe solid state detector and a suitable rod scanner. Photon energies of 276.6keV from {sup 239}Np (neutron capture (n,?) nuclear reaction) and 293.3keV from {sup 143}Ce (fission (n,f) nuclear reaction on both {sup 238}U and {sup 235}U) , are respectively along both axial and radial directions. Other measurements are performed using gold wires and foils along radial and axial directions of the reactor core. The three methods above resulted in a weighted average value of 93.18 ± 8.47 m-2 for the Total Buckling of this cylindrical core configuration with 28 control rods along its diameter with 568 fuel rods and only 271 pcm of excess reactivity. (author)

  20. Ultrasound field measurement using a binary lens

    CERN Document Server

    Clement, Gregory T; Kamakura, Tomoo

    2014-01-01

    Field characterization methods using a scattering target in the absence of a point-like receiver have been well described in which scattering is recorded by a relatively large receiver located outside the field of measurement. Unfortunately, such methods are prone to artifacts due to averaging across the receiver surface. To avoid this problem while simultaneously increasing the gain of a received signal, the present study introduces a binary plate lens designed to focus spherically-spreading waves onto a planar region having a nearly-uniform phase proportional to that of the target location. The lens is similar to a zone plate, but modified to produce a bi-convex-like behavior, such that it focuses both planar and spherically spreading waves. A measurement device suitable for characterizing narrowband ultrasound signals in air is designed around this lens by coupling it to a target and planar receiver. A prototype device is constructed and used to characterize the field of a highly-focused 400 kHz air transd...

  1. Measuring propagation speed of Coulomb fields

    Energy Technology Data Exchange (ETDEWEB)

    Sangro, R. de; Finocchiaro, G.; Patteri, P.; Piccolo, M.; Pizzella, G. [Istituto Nazionale di Fisica Nucleare, Laboratori Nazionali di Frascati, Frascati (Italy)

    2015-03-01

    The problem of gravity propagation has been subject of discussion for quite a long time: Newton, Laplace and, in relatively more modern times, Eddington pointed out that, if gravity propagated with finite velocity, planet motion around the sun would become unstable due to a torque originating from time lag of the gravitational interactions. Such an odd behavior can be found also in electromagnetism, when one computes the propagation of the electric fields generated by a set of uniformly moving charges. As a matter of fact the Lienard-Weichert retarded potential leads to the same formula as the one obtained assuming that the electric field propagate with infinite velocity. The Feynman explanation for this apparent paradox was based on the fact that uniform motions last indefinitely. To verify such an explanation, we performed an experiment to measure the time/space evolution of the electric field generated by an uniformly moving electron beam. The results we obtain, on a finite lifetime kinematical state, are compatible with an electric field rigidly carried by the beam itself. (orig.)

  2. Soil Water Balance Measurement in Field Scale

    Institute of Scientific and Technical Information of China (English)

    CHENZHI-XIONG

    1992-01-01

    A 5-year experiment on water balance has been conducted in a flat rainfed wheat field with an area of 66×100m2 in Fengqiu,Henan Province in China.Based on the analysis of semi-variance functions conducted with soil moisture samples taken from 77 nodes of a 10×10m2 grid,the soil moisture distribution in the field was structural with a temporal stability.According to the autocorrelation range of the semi-variance function,6 sites were selected for the determination of soil water conditions.The characteristic of probability density function of the differences of water storage in two sets of measurements showed that the distribution of these variables in the field was a normal one.The error in the estimation of the average of 5 random samples was 14% (α=0.10),and the errors of water consumption by wheat during the experiments were estimated to be 6-13%.Sime the experimental field was large enough to avoid any edge effect,the results obtained should tally with the actual situation.Yet the soil system was heterogeneous,so we must follow the principles of statistics and geostatistics when describing the system's status with the average of the samples.

  3. Development of a High Irradiance LED Configuration for Small Field of View Motion Estimation of Fertilizer Particles.

    Science.gov (United States)

    Cool, Simon; Pieters, Jan G; Mertens, Koen C; Mora, Sergio; Cointault, Frédéric; Dubois, Julien; van de Gucht, Tim; Vangeyte, Jürgen

    2015-11-12

    Better characterization of the fertilizer spreading process, especially the fertilizer pattern distribution on the ground, requires an accurate measurement of individual particle properties and dynamics. Both 2D and 3D high speed imaging techniques have been developed for this purpose. To maximize the accuracy of the predictions, a specific illumination level is required. This paper describes the development of a high irradiance LED system for high speed motion estimation of fertilizer particles. A spectral sensitivity factor was used to select the optimal LED in relation to the used camera from a range of commercially available high power LEDs. A multiple objective genetic algorithm was used to find the optimal configuration of LEDs resulting in the most homogeneous irradiance in the target area. Simulations were carried out for different lenses and number of LEDs. The chosen configuration resulted in an average irradiance level of 452 W/m² with coefficient of variation less than 2%. The algorithm proved superior and more flexible to other approaches reported in the literature and can be used for various other applications.

  4. Development of a High Irradiance LED Configuration for Small Field of View Motion Estimation of Fertilizer Particles

    Directory of Open Access Journals (Sweden)

    Simon Cool

    2015-11-01

    Full Text Available Better characterization of the fertilizer spreading process, especially the fertilizer pattern distribution on the ground, requires an accurate measurement of individual particle properties and dynamics. Both 2D and 3D high speed imaging techniques have been developed for this purpose. To maximize the accuracy of the predictions, a specific illumination level is required. This paper describes the development of a high irradiance LED system for high speed motion estimation of fertilizer particles. A spectral sensitivity factor was used to select the optimal LED in relation to the used camera from a range of commercially available high power LEDs. A multiple objective genetic algorithm was used to find the optimal configuration of LEDs resulting in the most homogeneous irradiance in the target area. Simulations were carried out for different lenses and number of LEDs. The chosen configuration resulted in an average irradiance level of 452 W/m2 with coefficient of variation less than 2%. The algorithm proved superior and more flexible to other approaches reported in the literature and can be used for various other applications.

  5. Conceptual design of the three-dimensional magnetic field configuration relevant to the magnetopause reconnection in the SPERF

    Science.gov (United States)

    Aohua, MAO; Yang, REN; Hantao, JI; Peng, E.; Ke, HAN; Zhibin, WANG; Qingmei, XIAO; Liyi, LI

    2017-03-01

    A new ground-based experimental device, the Space Plasma Environment Research Facility (SPERF), is being designed at Harbin Institute of Technology in China, with Asymmetric REconnection eXperiment-3 Dimensional (AREX-3D) as one of the experimental components to study the asymmetric reconnection dynamics relevant to the interaction between the interplanetary and magnetospheric plasmas. The asymmetry in the designed magnetic reconnection process not only refers to the distinct plasma parameters designed for the two upstream regions across the current sheet, but also refers to the inhomogeneity in the direction along the current sheet resulting from the designed 3D magnetic field geometry. These two asymmetries are fundamental features of the reconnection process at the Earth’s magnetopause. In experiment, the reconnection process is driven by a set of flux cores through coil-current-ramp-up from the ‘magnetosheath-side’ to interact with a dipole magnetic field generated by the Dipole Research EXperiment (DREX) coil on the ‘magnetosphere-side’. The AREX-3D will be able to investigate a range of important reconnection issues in 3D magnetic field geometry that is relevant to the Earth’s magnetopause. A wide range of plasma parameters can be achieved through inductive plasma generation with flux cores on the ‘magnetosheath-side’ and electron cyclotron resonance (ECR) with microwave sources on the ‘magnetosphere-side’, e.g. high (low) plasma density at experimental magnetosheath (dipole) side. Different reconnection regimes and geometries can be produced by adjusting plasma parameters and coil setups as well as coil current waveforms. The three-dimensional magnetic field configurations in the SPERF relevant to the dayside magnetopause reconnection are discussed in detail.

  6. Use of large-scale multi-configuration EMI measurements to characterize heterogeneous subsurface structures and their impact on crop productivity

    Science.gov (United States)

    Brogi, Cosimo; Huisman, Johan Alexander; Kaufmann, Manuela Sarah; von Hebel, Christian; van der Kruk, Jan; Vereecken, Harry

    2017-04-01

    Soil subsurface structures can play a key role in crop performance, especially during water stress periods. Geophysical techniques like electromagnetic induction EMI have been shown to be able of providing information about dominant shallow subsurface features. However, previous work with EMI has typically not reached beyond the field scale. The objective of this study is to use large-scale multi-configuration EMI to characterize patterns of soil structural organization (layering and texture) and the associated impact on crop vegetation at the km2 scale. For this, we carried out an intensive measurement campaign and collected high spatial resolution multi-configuration EMI data on an agricultural area of approx. 1 km2 (102 ha) near Selhausen (North Rhine-Westphalia, Germany) with a maximum depth of investigation of around 2.5 m. We measured using two EMI instruments simultaneously with a total of nine coil configurations. The instruments were placed inside polyethylene sleds that were pulled by an all-terrain-vehicle along parallel lines with a spacing of 2 to 2.5 m. The driving speed was between 5 and 7 km h-1 and we used a 0.2 Hz sampling frequency to obtain an in-line resolution of approximately 0.3 m. The survey area consists of almost 50 different fields managed in different way. The EMI measurements were collected between April and December 2016 within a few days after the harvest of each field. After data acquisition, EMI data were automatically filtered, temperature corrected, and interpolated onto a common grid. The resulting EMI maps allowed us to identify three main areas with different subsurface heterogeneities. The differences between these areas are likely related to the late quaternary geological history (Pleistocene and Holocene) of the area that resulted in spatially variable soil texture and layering, which has a strong impact on spatio-temporal soil water content variability. The high resolution surveys also allowed us to identify small scale

  7. Application of a Solar Wind Model Driven by Turbulence Dissipation to a 2D Magnetic Field Configuration

    CERN Document Server

    Lionello, Roberto; Downs, Cooper; Linker, Jon A; Mikić, Zoran

    2014-01-01

    Although it is widely accepted that photospheric motions provide the energy source and that the magnetic field must play a key role in the process, the detailed mechanisms responsible for heating the Sun's corona and accelerating the solar wind are still not fully understood. Cranmer et al. (2007) developed a sophisticated, 1D, time-steady model of the solar wind with turbulence dissipation. By varying the coronal magnetic field, they obtain, for a single choice of wave properties, a realistic range of slow and fast wind conditions with a sharp latitudinal transition between the two streams. Using a 1D, time-dependent model of the solar wind of Lionello et al. (2014), which incorporates turbulent dissipation of Alfv\\'en waves to provide heating and acceleration of the plasma, we have explored a similar configuration, obtaining qualitatively equivalent results. However, our calculations suggest that the rapid transition between slow and fast wind suggested by this 1D model may be disrupted in multidimensional ...

  8. Configuration-averaged open shell ab initio method for crystal field levels and magnetic properties of lanthanide(III) complexes

    CERN Document Server

    Heuvel, Willem Van den; Soncini, Alessandro

    2015-01-01

    We present an ab initio methodology dedicated to the determination of the electronic structure and magnetic properties of ground and low-lying excited states, i.e., the crystal field levels, in lanthanide(III) complexes. Currently, the most popular and successful ab initio approach is the CASSCF/RASSI-SO method, consisting of the optimization of multiple complete active space self-consistent field (CASSCF) spin eigenfunctions, followed by full diagonalization of the spin--orbit coupling (SOC) Hamiltonian in the basis of the CASSCF spin states featuring spin-dependent orbitals. Based on two simple observations valid for Ln(III) complexes, namely: (i) CASSCF 4f atomic orbitals are expected to change very little when optimized for different multiconfigurational states belonging to the 4f-electronic configuration, (ii) due to strong SOC the total spin is not a good quantum number, we propose here an efficient ab initio strategy which completely avoids any multiconfigurational calculation, by optimizing a unique s...

  9. Development of a magnetized coaxial plasma gun for compact toroid injection into the C-2 field-reversed configuration device.

    Science.gov (United States)

    Matsumoto, T; Sekiguchi, J; Asai, T; Gota, H; Garate, E; Allfrey, I; Valentine, T; Morehouse, M; Roche, T; Kinley, J; Aefsky, S; Cordero, M; Waggoner, W; Binderbauer, M; Tajima, T

    2016-05-01

    A compact toroid (CT) injector was developed for the C-2 device, primarily for refueling of field-reversed configurations. The CTs are formed by a magnetized coaxial plasma gun (MCPG), which consists of coaxial cylindrical electrodes and a bias coil for creating a magnetic field. First, a plasma ring is generated by a discharge between the electrodes and is accelerated by Lorenz self-force. Then, the plasma ring is captured by an interlinkage flux (poloidal flux). Finally, the fully formed CT is ejected from the MCPG. The MCPG described herein has two gas injection ports that are arranged tangentially on the outer electrode. A tungsten-coated inner electrode has a head which can be replaced with a longer one to extend the length of the acceleration region for the CT. The developed MCPG has achieved supersonic CT velocities of ∼100 km/s. Plasma parameters for electron density, electron temperature, and the number of particles are ∼5 × 10(21) m(-3), ∼40 eV, and 0.5-1.0 × 10(19), respectively.

  10. Field scale measurements of NH3 emissions

    Science.gov (United States)

    Neftel, Albrecht; Ammann, Christof; Kuhn, Uwe; Sintermann, Jörg; Lehuger, Simon; Gärtner, Andrea; Hirschberger, Rainer

    2010-05-01

    The uncertainty in the ammonia emissions after application of organic manure contributes to a large extent to the overall uncertainties of the nitrogen budget of managed grassland systems (Ammann et al., 2009). Due to the sticky nature of the ammonia molecule and the variability of the emission fluxes the experimental determination is still a major challenge and a wide spread range of emission factors can be found in the literature. We report on two field experiments performed in August 2009 at the NitroEurope site in Oensingen, Switzerland. The ammonia emission flux after liquid manure application was investigated simultaneously by various micrometeorological methods: (1) a mass balance approach measuring the horizontal advection flux with open-path FTIR sensors (Gärtner et al., 2008), (2) aerodynamic gradient methods, and (3) eddy covariance measurements based on a novel fast ammonia analyser. Due to the sequential application of the manure and the fast decrease of the ammonia volatilisation, detailed footprint calculations (Neftel et al., 2008) and corrections with a high temporal resolution were crucial for obtaining representative emission fluxes. The plausibility of flux measurements has been evaluated with back trajectories simulations (WindTrax, Flesch et al., 2009). The results of all applied flux measurement methods confirmed the low emission levels found earlier by Spirig et al. (2009). A comparison of the field observations with results of process oriented models showed considerable differences in the temporal course of the ammonia emission indicating the need for improvements of the models. References: Ammann, C., Spirig, C., Leifeld, J. and Neftel, A.: Assessment of the nitrogen and carbon budget of two managed temperate grassland fields, Agric. Ecosyst. Environ., 133, 150-162, 2009. Flesch, T.K., Harper, L.A., Desjardins, R.L., Gao, Z., and Crenna, B.: Multi-Source Emission Determination Using an Inverse-Dispersion Technique. Boundary-Layer Meteorol

  11. PM10 source measurement methodology: Field studies

    Energy Technology Data Exchange (ETDEWEB)

    Farthing, W.E.; Martin, R.S.; Dawes, S.S.; Williamson, A.D.

    1989-05-01

    Two candidate measurement methods, Constant Sampling Rate (CSR) and Exhaust Gas Recycle (EGR), have been developed to measure emissions of in-stack PM-10 particulate matter with aerodynamic diameter less than 10 micrometers. Two field tests were performed at the clinker cooler exhaust of a Portland cement plant to quantify precision and comparability of these techniques. In addition, accuracy was determined for total particulate measurement by comparison to Method 17. Collocated sampling trains were operated parallel with two Method 17 trains. In the second test, two CSR and one EGR trains were operated parallel to two Method 17 trains. The operating procedures used for the CSR and EGR trains are described in detail. In measurement of PM-10 and total particulate matter, the precision of both the CSR and EGR techniques was found to be of the same magnitude as Method 17 (approximately 5%). A small bias was found between CSR and EGR PM-10 results (15%) and between EGR and Method 17 total particulate matter (10%). Although small, these observed differences, combined with the results of laboratory studies reported elsewhere, led to a recommendation for an increase in the length of sampling nozzles. This modification improved cyclone performance and is incorporated into the nozzle geometries described in the application guides for CSR and EGR.

  12. Information configuration?

    OpenAIRE

    Lauro Cesar Araujo; Mamede Lima-Marques

    2016-01-01

    Introduction: The term "configuration information" has emerged in the works of Information Architecture; however, there isn’t a conceptualization of “configuration” within Information Architecture. Objective: The objective is propose a definition for "configuration" and "information configuration" within the Information Architecture discipline, and indicate a teleological corpus from configuration management that can be used as paxis in Information Architecture. Methodolo...

  13. Modified methods of stellar magnetic field measurements

    CERN Document Server

    Kholtygin, A F

    2013-01-01

    The standard methods of the magnetic field measurement, based on an analysis of the relation between the Stokes $V$-parameter and the first derivative of the total line profile intensity, were modified by applying a linear integral operator $\\hat{L}$ to the both sides of this relation. As the operator $\\hat{L}$, the operator of the wavelet transform with DOG-wavelets is used. The key advantage of the proposed method is an effective suppression of the noise contribution to the line profile and the Stokes parameter $V$. The efficiency of the method has been studied using the model line profiles with various noise contributions. To test the proposed method, the spectropolarimetric observations of the A0-type star $\\alpha^2\\,$ CVn, young O-type star $\\theta^1$ Ori C and A0 supergiant HD 92207 were used. The longitudinal magnetic field strengths for these stars calculated by our method appeared to be in a good agreement with those determined by other methods.

  14. Fast imaging diagnostics on the C-2U advanced beam-driven field-reversed configuration device

    Science.gov (United States)

    Granstedt, E. M.; Petrov, P.; Knapp, K.; Cordero, M.; Patel, V.

    2016-11-01

    The C-2U device employed neutral beam injection, end-biasing, and various particle fueling techniques to sustain a Field-Reversed Configuration (FRC) plasma. As part of the diagnostic suite, two fast imaging instruments with radial and nearly axial plasma views were developed using a common camera platform. To achieve the necessary viewing geometry, imaging lenses were mounted behind re-entrant viewports attached to welded bellows. During gettering, the vacuum optics were retracted and isolated behind a gate valve permitting their removal if cleaning was necessary. The axial view incorporated a stainless-steel mirror in a protective cap assembly attached to the vacuum-side of the viewport. For each system, a custom lens-based, high-throughput optical periscope was designed to relay the plasma image about half a meter to a high-speed camera. Each instrument also contained a remote-controlled filter wheel, set between shots to isolate a particular hydrogen or impurity emission line. The design of the camera platform, imaging performance, and sample data for each view is presented.

  15. Strong-field ionization rates of linear polyenes simulated with time-dependent configuration interaction with an absorbing potential

    Energy Technology Data Exchange (ETDEWEB)

    Krause, Pascal; Schlegel, H. Bernhard [Department of Chemistry, Wayne State University, Detroit, Michigan 48202-3489 (United States)

    2014-11-07

    The strong field ionization rates for ethylene, trans 1,3-butadiene, and trans,trans 1,3,5-hexatriene have been calculated using time-dependent configuration interaction with single excitations and a complex absorbing potential (TDCIS-CAP). The calculations used the aug-cc-pVTZ basis set with a large set of diffuse functions (3 s, 2 p, 3 d, and 1 f) on each atom. The absorbing boundary was placed 3.5 times the van der Waals radius from each atom. The simulations employed a seven-cycle cosine squared pulse with a wavelength of 800 nm. Ionization rates were calculated for intensities ranging from 0.3 × 10{sup 14} W/cm{sup 2} to 3.5 × 10{sup 14} W/cm{sup 2}. Ionization rates along the molecular axis increased markedly with increasing conjugation length. By contrast, ionization rates perpendicular to the molecular axis were almost independent of the conjugation length.

  16. Fast imaging diagnostics on the C-2U advanced beam-driven field-reversed configuration device

    Energy Technology Data Exchange (ETDEWEB)

    Granstedt, E. M., E-mail: egranstedt@trialphaenergy.com; Petrov, P.; Knapp, K.; Cordero, M.; Patel, V. [Tri Alpha Energy, P.O. Box 7010, Rancho Santa Margarita, California 92688 (United States)

    2016-11-15

    The C-2U device employed neutral beam injection, end-biasing, and various particle fueling techniques to sustain a Field-Reversed Configuration (FRC) plasma. As part of the diagnostic suite, two fast imaging instruments with radial and nearly axial plasma views were developed using a common camera platform. To achieve the necessary viewing geometry, imaging lenses were mounted behind re-entrant viewports attached to welded bellows. During gettering, the vacuum optics were retracted and isolated behind a gate valve permitting their removal if cleaning was necessary. The axial view incorporated a stainless-steel mirror in a protective cap assembly attached to the vacuum-side of the viewport. For each system, a custom lens-based, high-throughput optical periscope was designed to relay the plasma image about half a meter to a high-speed camera. Each instrument also contained a remote-controlled filter wheel, set between shots to isolate a particular hydrogen or impurity emission line. The design of the camera platform, imaging performance, and sample data for each view is presented.

  17. Influence of movable test section elements configuration on its drag and flow field uniformity at transonic speeds

    Science.gov (United States)

    Glazkov, S. A.; Gorbushin, A. R.; Osipova, S. L.; Semenov, A. V.

    2016-10-01

    The report describes the results of flow field experimental research in TsAGI T-128 transonic wind tunnel. During the tests Mach number, stagnation pressure, test section wall perforation ratio, angles between the test section panels and mixing chamber flaps varied. Based on the test results one determined corrections to the free-stream Mach number related to the flow speed difference in the model location and in the zone of static pressure measurement on the test section walls, nonuniformity of the longitudinal velocity component in the model location, optimal position of the movable test section elements to provide flow field uniformity in the test section and minimize the test leg drag.

  18. Theoretical description of the photopyroelectric technique in the slanted detector configuration for thermal diffusivity measurements in fluids

    Energy Technology Data Exchange (ETDEWEB)

    Rojas-Trigos, J.B., E-mail: rjosebruno@yahoo.com.mx [Instituto Politécnico Nacional, Centro de Investigación en Ciencia Aplicada y Tecnología Avanzada, Legaría 694, Colonia Irrigación, C.P. 11500 México D. F. (Mexico); Marín, E. [Instituto Politécnico Nacional, Centro de Investigación en Ciencia Aplicada y Tecnología Avanzada, Legaría 694, Colonia Irrigación, C.P. 11500 México D. F. (Mexico); Mansanares, A.M. [Instituto de Física Gleb Wataghin, Universidade Estadual de Campinas, UNICAMP, 13083-859 Campinas, SP (Brazil); Cedeño, E.; Juárez-Gracia, G.; Calderón, A. [Instituto Politécnico Nacional, Centro de Investigación en Ciencia Aplicada y Tecnología Avanzada, Legaría 694, Colonia Irrigación, C.P. 11500 México D. F. (Mexico)

    2014-04-01

    Highlights: • A model for photopyroelectric thermal characterization of fluids is presented. • A slanted detector configuration is considered with a finite measurement cell. • The mean temperature distribution in the photopyroelectric detector, as function of the beam spot position, is calculated. • The influence of the excitation beam spot size, the thermal diffusion length and size of the sample is discussed. • The high lateral resolution of the method observed in experiments is explain. - Abstract: This work presents an extended description about the theoretical aspects related to the generation of the photopyroelectric signal in a recently proposed wedge-like heat transmission detection configuration, which recreates the well-known Angstrom method (widely used for solid samples) for accurate thermal diffusivity measurement in gases and liquids. The presented model allows for the calculation of the temperature profile detected by the pyroelectric sensor as a function of the excitation beam position, and the study of the influence on it of several parameters, such as spot size, thermal properties of the absorber layer, and geometrical parameters of the measurement cell. Through computer simulations, it has been demonstrated that a narrow temperature distribution is created at the sensor surface, independently of the lateral diffusion of heat taking place at the sample's surface.

  19. Novel technique for measuring intermodal dispersion in optical fibers using the spectral interference in the Michelson interferometer configuration

    Science.gov (United States)

    Hlubina, Petr

    1999-07-01

    The spectral interference between two modes of an optical fiber, which shows up as a periodic modulation of the source spectrum at its output, cannot be used to measure intermodal dispersion in the optical fiber when the period of modulation is too small to be resolved by a spectrometer. We proposed a novel measuring technique utilizing a tandem configuration of a dispersive Michelson interferometer and a two-mode optical fiber in which the intermodal interference can be restored, and consequently spectral interference fringes can be resolved, even if a low-resolution spectrometer is used. In the tandem configuration of the Michelson interferometer and the two-mode optical fiber, the optical path difference (OPD) in the Michelson interferometer is adjusted close to the group OPD between modes of the optical fiber so that the low-frequency spectral modulation that can be processed is produced. The feasibility of this technique has successfully been demonstrated in obtaining the wavelength dependence of the group OPD between two modes of the optical fiber. Using the Fourier transform method in processing the measured spectral modulations and subtracting the effect of the dispersive Michelson interferometer, the intermodal dispersion of the two-mode optical fiber has been obtained.

  20. Flow field measurements in the cell culture unit

    Science.gov (United States)

    Walker, Stephen; Wilder, Mike; Dimanlig, Arsenio; Jagger, Justin; Searby, Nancy

    2002-01-01

    The cell culture unit (CCU) is being designed to support cell growth for long-duration life science experiments on the International Space Station (ISS). The CCU is a perfused loop system that provides a fluid environment for controlled cell growth experiments within cell specimen chambers (CSCs), and is intended to accommodate diverse cell specimen types. Many of the functional requirements depend on the fluid flow field within the CSC (e.g., feeding and gas management). A design goal of the CCU is to match, within experimental limits, all environmental conditions, other than the effects of gravity on the cells, whether the hardware is in microgravity ( micro g), normal Earth gravity, or up to 2g on the ISS centrifuge. In order to achieve this goal, two steps are being taken. The first step is to characterize the environmental conditions of current 1g cell biology experiments being performed in laboratories using ground-based hardware. The second step is to ensure that the design of the CCU allows the fluid flow conditions found in 1g to be replicated from microgravity up to 2g. The techniques that are being used to take these steps include flow visualization, particle image velocimetry (PIV), and computational fluid dynamics (CFD). Flow visualization using the injection of dye has been used to gain a global perspective of the characteristics of the CSC flow field. To characterize laboratory cell culture conditions, PIV is being used to determine the flow field parameters of cell suspension cultures grown in Erlenmeyer flasks on orbital shakers. These measured parameters will be compared to PIV measurements in the CSCs to ensure that the flow field that cells encounter in CSCs is within the bounds determined for typical laboratory experiments. Using CFD, a detailed simulation is being developed to predict the flow field within the CSC for a wide variety of flow conditions, including microgravity environments. Results from all these measurements and analyses of the

  1. Effects of the Measurement Configuration on the Simulation of Lightning-Aircraft Interaction

    Science.gov (United States)

    1988-08-01

    microseconds to a peak current of 200 kA will have a diameter of about 2 mm and its maximum magnetic field will be about 40 Tesla , producing a...usual electronic systems such as communications, navigation, autopilot systems, system monitoring, etc., but manufacturers are incorporating all...vector (in teslas ) 431 SPEC: F!CAT.IONS Par..rnoer f MGL -3 .f G \\ -4 [ *. CL- Mr,’, -7 IMGL- SI 0 -O 0 10 - -5 3 Frenuencv Response *3 dB Porutt ,7

  2. Near-field measurements of the even-order harmonics undetectable in far-field measurements

    Science.gov (United States)

    Moiseyev, Nimrod

    2016-12-01

    Even-order harmonics (EOHs) are generated for oriented molecules and for atoms under specific conditions. Here, we focus on the most common situations where EOHs are not observed in far-field measurements. We propose an experiment to show that the EOHs are produced close to the nucleus but are not detected in the far-field measurements due to destructive interferences of the propagated EOHs of the emitted radiation. However, Rydberg gas atoms (e.g., rubidium), which are out of the focus of the laser beam, are expected to be ionized due to their weak interaction with a specific EOH of helium, which is not observed by the far-field detector. The ionization energy of the Rydberg gas atoms should be in resonance with the single-photon energy of a specific EOH.

  3. Angular configuration of the knee. Comparison of conventional measurements and the QUESTOR precision radiography system

    Energy Technology Data Exchange (ETDEWEB)

    Sanfridsson, J. [Univ. Hospital, Lund (Sweden). Dept. of Diagnostic Radiology; Ryd, L. [Univ. Hospital, Lund (Sweden). Dept. of Orthopaedics; Eklund, K. [Univ. Hospital, Lund (Sweden). Dept. of Diagnostic Radiology; Kouvaras, Y. [Asklepeion Voulas Hospital, Athens (Greece). First Orthopaedic Dept.; Jonsson, K. [Univ. Hospital, Lund (Sweden). Dept. of Diagnostic Radiology

    1996-09-01

    Purpose: The aim of this study was to assess the QUESTOR Precision Radiography system (QPR) and to compare it with the routine hip-knee-ankle (HKA) angle measurements. The main was also to evaluate the robustness of the QPR system against the osseous changes of arthrotic disease. Material and Methods: Twenty-four patients, operated on with a high tibial osteotomy for medial gonarthrosis, were examined. The alignment of the leg was measured by the conventional technique and by the QPR method. Results and Conclusion: The 2 methods correlated well. The intraobserver variation in the QPR measurements was, with the exception of the capito-midcondylar-femoral shaft angle and the tibial plateau width, not affected by the osseous changes inflicted by the arthrotic process. The patients tolerated both systems well while the staff preferred the QPR system. (orig.).

  4. Three-dimensional photogrammetric measurement of magnetic field lines in the WEGA stellarator

    Energy Technology Data Exchange (ETDEWEB)

    Drewelow, Peter; Braeuer, Torsten; Otte, Matthias; Wagner, Friedrich; Werner, Andreas [Max-Planck-Institut fuer Plasmaphysik, EURATOM Association, Wendelsteinstr. 1, D-17491 Greifswald (Germany)

    2009-12-15

    The magnetic confinement of plasmas in fusion experiments can significantly degrade due to perturbations of the magnetic field. A precise analysis of the magnetic field in a stellarator-type experiment utilizes electrons as test particles following the magnetic field line. The usual fluorescent detector for this electron beam limits the provided information to two-dimensional cut views at certain toroidal positions. However, the technique described in this article allows measuring the three-dimensional structure of the magnetic field by means of close-range photogrammetry. After testing and optimizing the main diagnostic components, measurements of the magnetic field lines were accomplished with a spatial resolution of 5 mm. The results agree with numeric calculations, qualifying this technique as an additional tool to investigate magnetic field configurations in a stellarator. For a possible future application, ways are indicated on how to reduce experimental error sources.

  5. Three-dimensional photogrammetric measurement of magnetic field lines in the WEGA stellarator.

    Science.gov (United States)

    Drewelow, Peter; Bräuer, Torsten; Otte, Matthias; Wagner, Friedrich; Werner, Andreas

    2009-12-01

    The magnetic confinement of plasmas in fusion experiments can significantly degrade due to perturbations of the magnetic field. A precise analysis of the magnetic field in a stellarator-type experiment utilizes electrons as test particles following the magnetic field line. The usual fluorescent detector for this electron beam limits the provided information to two-dimensional cut views at certain toroidal positions. However, the technique described in this article allows measuring the three-dimensional structure of the magnetic field by means of close-range photogrammetry. After testing and optimizing the main diagnostic components, measurements of the magnetic field lines were accomplished with a spatial resolution of 5 mm. The results agree with numeric calculations, qualifying this technique as an additional tool to investigate magnetic field configurations in a stellarator. For a possible future application, ways are indicated on how to reduce experimental error sources.

  6. Pressure measurements on a forward-swept wing-canard configuration

    CSIR Research Space (South Africa)

    Lombardi, G

    1994-03-01

    Full Text Available . Pressure measurements were carried out on 320 points of the wing surface, in a medium speed wind tunnel. The results show that the canard effect is significantly dependent on canard position and that very small variations in the aerodynamic characteristics...

  7. OSMOSE program : statistical review of oscillation measurements in the MINERVE reactor R1-UO2 configuration.

    Energy Technology Data Exchange (ETDEWEB)

    Stoven, G.; Klann, R.; Zhong, Z.; Nuclear Engineering Division

    2007-08-28

    The OSMOSE program is a collaboration on reactor physics experiments between the United States Department of Energy and the France Commissariat Energie Atomique. At the working level, it is a collaborative effort between the Argonne National Laboratory and the CEA Cadarache Research Center. The objective of this program is to measure very accurate integral reaction rates in representative spectra for the actinides important to future nuclear system designs, and to provide the experimental data for improving the basic nuclear data files. The main outcome of the OSMOSE measurement program will be an experimental database of reactivity-worth measurements in different neutron spectra for the heavy nuclides. This database can then be used as a benchmark to verify and validate reactor analysis codes. The OSMOSE program (Oscillation in Minerve of isotopes in Eupraxic Spectra) aims at improving neutronic predictions of advanced nuclear fuels through oscillation measurements in the MINERVE facility on samples containing the following separated actinides: {sup 232}Th, {sup 233}U, {sup 234}U, {sup 235}U, {sup 236}U, {sup 238}U, {sup 237}Np, {sup 238}Pu, {sup 239}Pu, {sup 240}Pu, {sup 241}Pu, {sup 242}Pu, {sup 241}Am, {sup 243}Am, {sup 244}Cm, and {sup 245}Cm. The first part of this report provides an overview of the experimental protocol and the typical processing of a series of experimental results which is currently performed at CEA-Cadarache. In the second part of the report, improvements to this technique are presented, as well as the program that was created to process oscillation measurement results from the MINERVE facility in the future.

  8. Preliminary Results of Performance Measurements on a Cylindrical Hall-Effect Thruster with Magnetic Field Generated by Permanent Magnets

    Science.gov (United States)

    Polzin, K. A.; Raitses, Y.; Merino, E.; Fisch, N. J.

    2008-01-01

    The performance of a low-power cylindrical Hall thruster, which more readily lends itself to miniaturization and low-power operation than a conventional (annular) Hall thruster, was measured using a planar plasma probe and a thrust stand. The field in the cylindrical thruster was produced using permanent magnets, promising a power reduction over previous cylindrical thruster iterations that employed electromagnets to generate the required magnetic field topology. Two sets of ring-shaped permanent magnets are used, and two different field configurations can be produced by reorienting the poles of one magnet relative to the other. A plasma probe measuring ion flux in the plume is used to estimate the current utilization for the two magnetic configurations. The measurements indicate that electron transport is impeded much more effectively in one configuration, implying a higher thrust efficiency. Preliminary thruster performance measurements on this configuration were obtained over a power range of 100-250 W. The thrust levels over this power range were 3.5-6.5 mN, with anode efficiencies and specific impulses spanning 14-19% and 875- 1425 s, respectively. The magnetic field in the thruster was lower for the thrust measurements than the plasma probe measurements due to heating and weakening of the permanent magnets, reducing the maximum field strength from 2 kG to roughly 750-800 G. The discharge current levels observed during thrust stand testing were anomalously high compared to those levels measured in previous experiments with this thruster.

  9. A new measurement of antineutrino oscillation with the full detector configuration at Daya Bay

    CERN Document Server

    An, F.P.; Band, H.R.; Bishai, M.; Blyth, S.; Butorov, I.; Cao, G.F.; Cao, J.; Cen, W.R.; Chan, Y.L.; Chang, J.F.; Chang, L.C.; Chang, Y.; Chen, H.S.; Chen, Q.Y.; Chen, S.M.; Chen, Y.X.; Chen, Y.; Cheng, J.H.; Cheng, J.; Cheng, Y.P.; Cherwinka, J.J.; Chu, M.C.; Cummings, J.P.; de Arcos, J.; Deng, Z.Y.; Ding, X.F.; Ding, Y.Y.; Diwan, M.V.; Draeger, E.; Dwyer, D.A.; Edwards, W.R.; Ely, S.R.; Gill, R.; Gonchar, M.; Gong, G.H.; Gong, H.; Grassi, M.; Gu, W.Q.; Guan, M.Y.; Guo, L.; Guo, X.H.; Hackenburg, R.W.; Han, R.; Hans, S.; He, M.; Heeger, K.M.; Heng, Y.K.; Hor, Y.K.; Hsiung, Y.B.; Hu, B.Z.; Hu, L.M.; Hu, L.J.; Hu, T.; Hu, W.; Huang, E.C.; Huang, H.X.; Huang, X.T.; Huber, P.; Hussain, G.; Jaffe, D.E.; Jaffke, P.; Jen, K.L.; Jetter, S.; Ji, X.P.; Ji, X.L.; Jiao, J.B.; Johnson, R.A.; Kang, L.; Kettell, S.H.; Kramer, M.; Kwan, K.K.; Kwok, M.W.; Kwok, T.; Langford, T.J.; Lau, K.; Lebanowski, L.; Lee, J.; Lei, R.T.; Leitner, R.; Leung, A.; Leung, J.K.C.; Lewis, C.A.; Li, D.J.; Li, F.; Li, G.S.; Li, Q.J.; Li, S.C.; Li, W.D.; Li, X.N.; Li, X.Q.; Li, Y.F.; Li, Z.B.; Liang, H.; Lin, C.J.; Lin, G.L.; Lin, P.Y.; Lin, S.K.; Ling, J.J.; Link, J.M.; Littenberg, L.; Littlejohn, B.R.; Liu, D.W.; Liu, H.; Liu, J.L.; Liu, J.C.; Liu, S.S.; Lu, C.; Lu, H.Q.; Lu, J.S.; Luk, K.B.; Ma, Q.M.; Ma, X.Y.; Ma, X.B.; Ma, Y.Q.; McDonald, K.T.; McKeown, R.D.; Meng, Y.; Mitchell, I.; Kebwaro, J.Monari; Nakajima, Y.; Napolitano, J.; Naumov, D.; Naumova, E.; Ngai, H.Y.; Ning, Z.; Ochoa-Ricoux, J.P.; Olshevski, A.; Patton, S.; Pec, V.; Peng, J.C.; Piilonen, L.E.; Pinsky, L.; Pun, C.S.J.; Qi, F.Z.; Qi, M.; Qian, X.; Raper, N.; Ren, B.; Ren, J.; Rosero, R.; Roskovec, B.; Ruan, X.C.; Shao, B.B.; Steiner, H.; Sun, G.X.; Sun, J.L.; Tang, W.; Themann, H.; Tsang, K.V.; Tull, C.E.; Tung, Y.C.; Viaux, N.; Viren, B.; Vorobel, V.; Wang, C.H.; Wang, M.; Wang, N.Y.; Wang, R.G.; Wang, W.; Wang, W.W.; Wang, X.; Wang, Y.F.; Wang, Z.; Wang, Z.; Wang, Z.M.; Wei, H.Y.; Wen, L.J.; Whisnant, K.; White, C.G.; Whitehead, L.; Wise, T.; Wong, H.L.H.; Wong, S.C.F.; Worcester, E.; Wu, Q.; Xia, D.M.; Xia, J.K.; Xia, X.; Xing, Z.Z.; Xu, J.Y.; Xu, J.L.; Xu, J.; Xu, Y.; Xue, T.; Yan, J.; Yang, C.G.; Yang, L.; Yang, M.S.; Yang, M.T.; Ye, M.; Yeh, M.; Yeh, Y.S.; Young, B.L.; Yu, G.Y.; Yu, Z.Y.; Zang, S.L.; Zhan, L.; Zhang, C.; Zhang, H.H.; Zhang, J.W.; Zhang, Q.M.; Zhang, Y.M.; Zhang, Y.X.; Zhang, Y.M.; Zhang, Z.J.; Zhang, Z.Y.; Zhang, Z.P.; Zhao, J.; Zhao, Q.W.; Zhao, Y.F.; Zhao, Y.B.; Zheng, L.; Zhong, W.L.; Zhou, L.; Zhou, N.; Zhuang, H.L.; Zou, J.H.

    2015-01-01

    We report a new measurement of electron antineutrino disappearance using the fully-constructed Daya Bay Reactor Neutrino Experiment. The final two of eight antineutrino detectors were installed in the summer of 2012. Including the 404 days of data collected from October 2012 to November 2013 resulted in a total exposure of 6.9$\\times$10$^5$ GW$_{\\rm th}$-ton-days, a 3.6 times increase over our previous results. Improvements in energy calibration limited variations between detectors to 0.2%. Removal of six $^{241}$Am-$^{13}$C radioactive calibration sources reduced the background by a factor of two for the detectors in the experimental hall furthest from the reactors. Direct prediction of the antineutrino signal in the far detectors based on the measurements in the near detectors explicitly minimized the dependence of the measurement on models of reactor antineutrino emission. The uncertainties in our estimates of $\\sin^{2}2\\theta_{13}$ and $|\\Delta m^2_{ee}|$ were halved as a result of these improvements. Ana...

  10. New measurement of antineutrino oscillation with the full detector configuration at Daya Bay.

    Science.gov (United States)

    An, F P; Balantekin, A B; Band, H R; Bishai, M; Blyth, S; Butorov, I; Cao, G F; Cao, J; Cen, W R; Chan, Y L; Chang, J F; Chang, L C; Chang, Y; Chen, H S; Chen, Q Y; Chen, S M; Chen, Y X; Chen, Y; Cheng, J H; Cheng, J; Cheng, Y P; Cherwinka, J J; Chu, M C; Cummings, J P; de Arcos, J; Deng, Z Y; Ding, X F; Ding, Y Y; Diwan, M V; Draeger, E; Dwyer, D A; Edwards, W R; Ely, S R; Gill, R; Gonchar, M; Gong, G H; Gong, H; Grassi, M; Gu, W Q; Guan, M Y; Guo, L; Guo, X H; Hackenburg, R W; Han, R; Hans, S; He, M; Heeger, K M; Heng, Y K; Higuera, A; Hor, Y K; Hsiung, Y B; Hu, B Z; Hu, L M; Hu, L J; Hu, T; Hu, W; Huang, E C; Huang, H X; Huang, X T; Huber, P; Hussain, G; Jaffe, D E; Jaffke, P; Jen, K L; Jetter, S; Ji, X P; Ji, X L; Jiao, J B; Johnson, R A; Kang, L; Kettell, S H; Kramer, M; Kwan, K K; Kwok, M W; Kwok, T; Langford, T J; Lau, K; Lebanowski, L; Lee, J; Lei, R T; Leitner, R; Leung, K Y; Leung, J K C; Lewis, C A; Li, D J; Li, F; Li, G S; Li, Q J; Li, S C; Li, W D; Li, X N; Li, X Q; Li, Y F; Li, Z B; Liang, H; Lin, C J; Lin, G L; Lin, P Y; Lin, S K; Ling, J J; Link, J M; Littenberg, L; Littlejohn, B R; Liu, D W; Liu, H; Liu, J L; Liu, J C; Liu, S S; Lu, C; Lu, H Q; Lu, J S; Luk, K B; Ma, Q M; Ma, X Y; Ma, X B; Ma, Y Q; Martinez Caicedo, D A; McDonald, K T; McKeown, R D; Meng, Y; Mitchell, I; Monari Kebwaro, J; Nakajima, Y; Napolitano, J; Naumov, D; Naumova, E; Ngai, H Y; Ning, Z; Ochoa-Ricoux, J P; Olshevski, A; Park, J; Patton, S; Pec, V; Peng, J C; Piilonen, L E; Pinsky, L; Pun, C S J; Qi, F Z; Qi, M; Qian, X; Raper, N; Ren, B; Ren, J; Rosero, R; Roskovec, B; Ruan, X C; Shao, B B; Steiner, H; Sun, G X; Sun, J L; Tang, W; Taychenachev, D; Themann, H; Tsang, K V; Tull, C E; Tung, Y C; Viaux, N; Viren, B; Vorobel, V; Wang, C H; Wang, M; Wang, N Y; Wang, R G; Wang, W; Wang, W W; Wang, X; Wang, Y F; Wang, Z; Wang, Z; Wang, Z M; Wei, H Y; Wen, L J; Whisnant, K; White, C G; Whitehead, L; Wise, T; Wong, H L H; Wong, S C F; Worcester, E; Wu, Q; Xia, D M; Xia, J K; Xia, X; Xing, Z Z; Xu, J Y; Xu, J L; Xu, J; Xu, Y; Xue, T; Yan, J; Yang, C G; Yang, L; Yang, M S; Yang, M T; Ye, M; Yeh, M; Yeh, Y S; Young, B L; Yu, G Y; Yu, Z Y; Zang, S L; Zhan, L; Zhang, C; Zhang, H H; Zhang, J W; Zhang, Q M; Zhang, Y M; Zhang, Y X; Zhang, Y M; Zhang, Z J; Zhang, Z Y; Zhang, Z P; Zhao, J; Zhao, Q W; Zhao, Y F; Zhao, Y B; Zheng, L; Zhong, W L; Zhou, L; Zhou, N; Zhuang, H L; Zou, J H

    2015-09-11

    We report a new measurement of electron antineutrino disappearance using the fully constructed Daya Bay Reactor Neutrino Experiment. The final two of eight antineutrino detectors were installed in the summer of 2012. Including the 404 days of data collected from October 2012 to November 2013 resulted in a total exposure of 6.9×10^{5} GW_{th}  ton days, a 3.6 times increase over our previous results. Improvements in energy calibration limited variations between detectors to 0.2%. Removal of six ^{241}Am-^{13}C radioactive calibration sources reduced the background by a factor of 2 for the detectors in the experimental hall furthest from the reactors. Direct prediction of the antineutrino signal in the far detectors based on the measurements in the near detectors explicitly minimized the dependence of the measurement on models of reactor antineutrino emission. The uncertainties in our estimates of sin^{2}2θ_{13} and |Δm_{ee}^{2}| were halved as a result of these improvements. An analysis of the relative antineutrino rates and energy spectra between detectors gave sin^{2}2θ_{13}=0.084±0.005 and |Δm_{ee}^{2}|=(2.42±0.11)×10^{-3}  eV^{2} in the three-neutrino framework.

  11. VECTOR TOMOGRAPHY FOR THE CORONAL MAGNETIC FIELD. II. HANLE EFFECT MEASUREMENTS

    Energy Technology Data Exchange (ETDEWEB)

    Kramar, M. [Physics Department, The Catholic University of America, 620 Michigan Avenue NE, Washington, DC 20064 (United States); Inhester, B. [Max-Planck-Institut fuer Sonnensystemforschung, Max-Plank-Str. 2, D-37191 Katlenburg-Lindau (Germany); Lin, H. [Institute for Astronomy, University of Hawaii at Manoa, 34 Ohia Ku Street, Pukalani, Maui, HI 96768 (United States); Davila, J., E-mail: maxim.i.kramar@nasa.gov, E-mail: Joseph.M.Davila@nasa.gov, E-mail: inhester@mps.mpg.de, E-mail: lin@ifa.hawaii.edu [NASA-GSFC, Code 671, Greenbelt, MD 20771 (United States)

    2013-09-20

    In this paper, we investigate the feasibility of saturated coronal Hanle effect vector tomography or the application of vector tomographic inversion techniques to reconstruct the three-dimensional magnetic field configuration of the solar corona using linear polarization measurements of coronal emission lines. We applied Hanle effect vector tomographic inversion to artificial data produced from analytical coronal magnetic field models with equatorial and meridional currents and global coronal magnetic field models constructed by extrapolation of real photospheric magnetic field measurements. We tested tomographic inversion with only Stokes Q, U, electron density, and temperature inputs to simulate observations over large limb distances where the Stokes I parameters are difficult to obtain with ground-based coronagraphs. We synthesized the coronal linear polarization maps by inputting realistic noise appropriate for ground-based observations over a period of two weeks into the inversion algorithm. We found that our Hanle effect vector tomographic inversion can partially recover the coronal field with a poloidal field configuration, but that it is insensitive to a corona with a toroidal field. This result demonstrates that Hanle effect vector tomography is an effective tool for studying the solar corona and that it is complementary to Zeeman effect vector tomography for the reconstruction of the coronal magnetic field.

  12. Distant Measurement of Plethysmographic Signal in Various Lighting Conditions Using Configurable Frame-Rate Camera

    Directory of Open Access Journals (Sweden)

    Przybyło Jaromir

    2016-12-01

    Full Text Available Videoplethysmography is currently recognized as a promising noninvasive heart rate measurement method advantageous for ubiquitous monitoring of humans in natural living conditions. Although the method is considered for application in several areas including telemedicine, sports and assisted living, its dependence on lighting conditions and camera performance is still not investigated enough. In this paper we report on research of various image acquisition aspects including the lighting spectrum, frame rate and compression. In the experimental part, we recorded five video sequences in various lighting conditions (fluorescent artificial light, dim daylight, infrared light, incandescent light bulb using a programmable frame rate camera and a pulse oximeter as the reference. For a video sequence-based heart rate measurement we implemented a pulse detection algorithm based on the power spectral density, estimated using Welch’s technique. The results showed that lighting conditions and selected video camera settings including compression and the sampling frequency influence the heart rate detection accuracy. The average heart rate error also varies from 0.35 beats per minute (bpm for fluorescent light to 6.6 bpm for dim daylight.

  13. Configuring balanced scorecards for measuring health system performance: evidence from 5 years' evaluation in Afghanistan.

    Science.gov (United States)

    Edward, Anbrasi; Kumar, Binay; Kakar, Faizullah; Salehi, Ahmad Shah; Burnham, Gilbert; Peters, David H

    2011-07-01

    In 2004, Afghanistan pioneered a balanced scorecard (BSC) performance system to manage the delivery of primary health care services. This study examines the trends of 29 key performance indicators over a 5-year period between 2004 and 2008. Independent evaluations of performance in six domains were conducted annually through 5,500 patient observations and exit interviews and 1,500 provider interviews in >600 facilities selected by stratified random sampling in each province. Generalized estimating equation (GEE) models were used to assess trends in BSC parameters. There was a progressive improvement in the national median scores scaled from 0-100 between 2004 and 2008 in all six domains: patient and community satisfaction of services (65.3-84.5, pperformance benchmarking during the 5-year period. However, scorecard reconfigurations are needed to integrate effectiveness and efficiency measures and accommodate changes in health systems policy and strategy architecture to ensure its continued relevance and effectiveness as a comprehensive health system performance measure. The process of BSC design and implementation can serve as a valuable prototype for health policy planners managing performance in similar health care contexts. Please see later in the article for the Editors' Summary.

  14. Configuring Balanced Scorecards for Measuring Health System Performance: Evidence from 5 Years' Evaluation in Afghanistan

    Science.gov (United States)

    Edward, Anbrasi; Kumar, Binay; Kakar, Faizullah; Salehi, Ahmad Shah; Burnham, Gilbert; Peters, David H.

    2011-01-01

    Background In 2004, Afghanistan pioneered a balanced scorecard (BSC) performance system to manage the delivery of primary health care services. This study examines the trends of 29 key performance indicators over a 5-year period between 2004 and 2008. Methods and Findings Independent evaluations of performance in six domains were conducted annually through 5,500 patient observations and exit interviews and 1,500 provider interviews in >600 facilities selected by stratified random sampling in each province. Generalized estimating equation (GEE) models were used to assess trends in BSC parameters. There was a progressive improvement in the national median scores scaled from 0–100 between 2004 and 2008 in all six domains: patient and community satisfaction of services (65.3–84.5, pperformance benchmarking during the 5-year period. However, scorecard reconfigurations are needed to integrate effectiveness and efficiency measures and accommodate changes in health systems policy and strategy architecture to ensure its continued relevance and effectiveness as a comprehensive health system performance measure. The process of BSC design and implementation can serve as a valuable prototype for health policy planners managing performance in similar health care contexts. Please see later in the article for the Editors' Summary PMID:21814499

  15. Field methods for measuring concentrated flow erosion

    Science.gov (United States)

    Castillo, C.; Pérez, R.; James, M. R.; Quinton, J. N.; Taguas, E. V.; Gómez, J. A.

    2012-04-01

    Many studies have stressed the importance of gully erosion in the overall soil loss and sediment yield of agricultural catchments, for instance in recent years (Vandaele and Poesen, 1995; De Santisteban et al., 2006; Wu el al, 2008). Several techniques have been used for determining gully erosion in field studies. The conventional techniques involved the use of different devices (i.e. ruler, pole, tape, micro-topographic profilers, total station) to calculate rill and gully volumes through the determination of cross sectional areas and length of reaches (Casalí et al, 1999; Hessel and van Asch, 2003). Optical devices (i.e. laser profilemeters) have also been designed for the purpose of rapid and detailed assessment of cross sectional areas in gully networks (Giménez et al., 2009). These conventional 2d methods provide a simple and un-expensive approach for erosion evaluation, but are time consuming to carry out if a good accuracy is required. On the other hand, remote sensing techniques are being increasingly applied to gully erosion investigation such as aerial photography used for big-scale, long-term, investigations (e.g. Martínez-Casasnovas et al., 2004; Ionita, 2006), airborne and terrestrial LiDAR datasets for gully volume evaluation (James et al., 2007; Evans and Lindsay, 2010) and recently, major advances in 3D photo-reconstruction techniques (Welty et al. 2010, James et al., 2011). Despite its interest, few studies simultaneously compare the accuracies of the range of conventional and remote sensing techniques used, or define the most suitable method for a particular scale, given and time and cost constraints. That was the reason behind the International Workshop Innovations in the evaluation and measurement of rill and gully erosion, held in Cordoba in May 2011 and from which derive part of the materials presented in this abstract. The main aim of this work was to compare the accuracy and time requirements of traditional (2D) and recently developed

  16. Method and apparatus for measuring weak magnetic fields

    DEFF Research Database (Denmark)

    1995-01-01

    When measuring weak magnetic fields, a container containing a medium, such as a solution containing a stable radical, is placed in a polarising magnetic field, which is essentially at right angles to the field to be measured. The polarising field is interrupted rapidly, the interruption being...

  17. Measurement of antineutrino oscillation with the full detector configuration at Daya Bay

    CERN Document Server

    Grassi, Marco

    2016-01-01

    In this poster, we present the latest measurement of electron antineutrino disappearance using the fully constructed Daya Bay Reactor Neutrino Experiment. A total exposure of $6.9 \\times 10^5$ GW$_{\\mathrm{th}}$ ton days was achieved in November 2013 after 617 day of data taking. The most precise estimates to date of the neutrino mass and mixing parameters $|\\Delta \\mathrm{m}^2_{ee}|$ and $\\sin^2 2 \\theta_{13}$ were obtained with an analysis of the relative antineutrino rates and energy spectra between detectors. The value of the two parameters was found to be $\\sin^2 2 \\theta_{13} = 0.084 \\pm 0.005$ and $|\\Delta \\mathrm{m}^2_{ee}| = (2.42 \\pm 0.11) \\times 10^{-3}\\,\\mathrm{eV}^2$. This report focuses in particular on describing how improvements in the calibration and in the energy response model contributed to achieve this result.

  18. Configuring balanced scorecards for measuring health system performance: evidence from 5 years' evaluation in Afghanistan.

    Directory of Open Access Journals (Sweden)

    Anbrasi Edward

    2011-07-01

    Full Text Available BACKGROUND: In 2004, Afghanistan pioneered a balanced scorecard (BSC performance system to manage the delivery of primary health care services. This study examines the trends of 29 key performance indicators over a 5-year period between 2004 and 2008. METHODS AND FINDINGS: Independent evaluations of performance in six domains were conducted annually through 5,500 patient observations and exit interviews and 1,500 provider interviews in >600 facilities selected by stratified random sampling in each province. Generalized estimating equation (GEE models were used to assess trends in BSC parameters. There was a progressive improvement in the national median scores scaled from 0-100 between 2004 and 2008 in all six domains: patient and community satisfaction of services (65.3-84.5, p<0.0001; provider satisfaction (65.4-79.2, p<0.01; capacity for service provision (47.4-76.4, p<0.0001; quality of services (40.5-67.4, p<0.0001; and overall vision for pro-poor and pro-female health services (52.0-52.6. The financial domain also showed improvement until 2007 (84.4-95.7, p<0.01, after which user fees were eliminated. By 2008, all provinces achieved the upper benchmark of national median set in 2004. CONCLUSIONS: The BSC has been successfully employed to assess and improve health service capacity and service delivery using performance benchmarking during the 5-year period. However, scorecard reconfigurations are needed to integrate effectiveness and efficiency measures and accommodate changes in health systems policy and strategy architecture to ensure its continued relevance and effectiveness as a comprehensive health system performance measure. The process of BSC design and implementation can serve as a valuable prototype for health policy planners managing performance in similar health care contexts. Please see later in the article for the Editors' Summary.

  19. Shielding Characteristics Using an Ultrasonic Configurable Fan Artificial Noise Source to Generate Modes - Experimental Measurements and Analytical Predictions

    Science.gov (United States)

    Sutliff, Daniel L.; Walker, Bruce E.

    2014-01-01

    An Ultrasonic Configurable Fan Artificial Noise Source (UCFANS) was designed, built, and tested in support of the NASA Langley Research Center's 14x22 wind tunnel test of the Hybrid Wing Body (HWB) full 3-D 5.8% scale model. The UCFANS is a 5.8% rapid prototype scale model of a high-bypass turbofan engine that can generate the tonal signature of proposed engines using artificial sources (no flow). The purpose of the program was to provide an estimate of the acoustic shielding benefits possible from mounting an engine on the upper surface of a wing; a flat plate model was used as the shielding surface. Simple analytical simulations were used to preview the radiation patterns - Fresnel knife-edge diffraction was coupled with a dense phased array of point sources to compute shielded and unshielded sound pressure distributions for potential test geometries and excitation modes. Contour plots of sound pressure levels, and integrated power levels, from nacelle alone and shielded configurations for both the experimental measurements and the analytical predictions are presented in this paper.

  20. Measuring health care efficiency with a tripartite configuration under the "National" Health Insurance system

    Institute of Scientific and Technical Information of China (English)

    Victor B.Kreng; Yang Shao-wei; Lin Chien-Hsu

    2014-01-01

    Background The "National" Health Insurance (NHI) in Taiwan,China is a single-payer system that was introduced in 1995 to provide universal health care.It is worth noting that three stakeholders are involved in Taiwan's NHI,which can be seen as a triangular governance regime between the Bureau of "National" Health Insurance (BNHI),the insured and providers.Accordingly,this study intended to assess the efficiency of various different production processes that occur among these stakeholders in Taiwan's NHI system.Methods A two-stage relational Data Envelopment Analysis (DEA) model is adopted to investigate the sub-process efficiencies of the health care resources held by 23 cities and counties through stages Ⅰ or Ⅱ,where the outputs of the first stage serve the inputs of the second.The dataset was collected from the annual reports published by the Department of Health,Taiwan,China.Results Under the proposed framework,the efficiency of the whole process can be obtained from the product of productivity and allocative efficiency.Ten DMUs are efficient either in stages Ⅰ or Ⅱ,with only two DMUs being efficient with regard to both sub-processes.Conclusion The relational DEA model not only demonstrates the physical relationship between the whole process and the sub-process components,but also produces reliable outcomes in efficiency measurement among different stakeholders in Taiwan's NHI system.

  1. Velocity field measurements in the wake of a propeller model

    Science.gov (United States)

    Mukund, R.; Kumar, A. Chandan

    2016-10-01

    Turboprop configurations are being revisited for the modern-day regional transport aircrafts for their fuel efficiency. The use of laminar flow wings is an effort in this direction. One way to further improve their efficiency is by optimizing the flow over the wing in the propeller wake. Previous studies have focused on improving the gross aerodynamic characteristics of the wing. It is known that the propeller slipstream causes early transition of the boundary layer on the wing. However, an optimized design of the propeller and wing combination could delay this transition and decrease the skin friction drag. Such a wing design would require the detailed knowledge of the development of the slipstream in isolated conditions. There are very few studies in the literature addressing the requirements of transport aircraft having six-bladed propeller and cruising at a high propeller advance ratio. Low-speed wind tunnel experiments have been conducted on a powered propeller model in isolated conditions, measuring the velocity field in the vertical plane behind the propeller using two-component hot-wire anemometry. The data obtained clearly resolved the mean velocity, the turbulence, the ensemble phase averages and the structure and development of the tip vortex. The turbulence in the slipstream showed that transition could be close to the leading edge of the wing, making it a fine case for optimization. The development of the wake with distance shows some interesting flow features, and the data are valuable for flow computation and optimization.

  2. Distance measurement based on light field geometry and ray tracing.

    Science.gov (United States)

    Chen, Yanqin; Jin, Xin; Dai, Qionghai

    2017-01-09

    In this paper, we propose a geometric optical model to measure the distances of object planes in a light field image. The proposed geometric optical model is composed of two sub-models based on ray tracing: object space model and image space model. The two theoretic sub-models are derived on account of on-axis point light sources. In object space model, light rays propagate into the main lens and refract inside it following the refraction theorem. In image space model, light rays exit from emission positions on the main lens and subsequently impinge on the image sensor with different imaging diameters. The relationships between imaging diameters of objects and their corresponding emission positions on the main lens are investigated through utilizing refocusing and similar triangle principle. By combining the two sub-models together and tracing light rays back to the object space, the relationships between objects' imaging diameters and corresponding distances of object planes are figured out. The performance of the proposed geometric optical model is compared with existing approaches using different configurations of hand-held plenoptic 1.0 cameras and real experiments are conducted using a preliminary imaging system. Results demonstrate that the proposed model can outperform existing approaches in terms of accuracy and exhibits good performance at general imaging range.

  3. Joint inversion of multi-configuration electromagnetic induction measurements to estimate soil wetting patterns during surface drip irrigation

    Science.gov (United States)

    Jadoon, Khan Z.; Moghadas, Davood; Jadoon, Aurangzeb; Missimer, Thomas M.; McCabe, Matthew

    2014-05-01

    In arid and semi-arid regions, development of precise information on the soil wetting pattern is important to optimize drip irrigation system design for sustainable agricultural water management. Usually mathematical models are commonly used to describe infiltration from a point source to design and manage drip irrigation systems. The extent to which water migrates laterally and vertically away from the drip emitter depends on many factors, including dripper discharge rate, the frequency of water application, duration of drip emission, the soil hydraulic characteristics, initial conditions, evaporation, root water uptake and root distribution patterns. However, several simplified assumptions in the mathematical models affect their utility to provide useful design information. In this respect, non-invasive geophysical methods, i.e., low frequency electromagnetic induction (EMI) systems are becoming powerful tools to map spatial and temporal soil moisture patterns due to fast measurement capability and sensitivity to soil water content and salinity. In this research, a new electromagnetic system, the CMD mini-Explorer, is used for soil characterization to measure the wetting patterns of drip irrigation systems using joint inversion of multi-configuration EMI measurements. Six transects of EMI measurements were carried out in a farm where Acacia trees are irrigated with brackish water using a drip irrigation system. EMI reference data (ground-truths) were calculated using vertical soil electrical conductivity recorded in different trenches along one of the measurement transects. Reference data is used for calibration to minimize the instrumental shifts which often occur in EMI data. Global and local optimization algorithms are used sequentially, to minimize the misfit between the measured and modeled apparent electrical conductivity (δa) to reconstruct the vertical electrical conductivity profile. The electromagnetic forward model based on full solution of Maxwell

  4. Precision insolation measurement under field conditions

    Science.gov (United States)

    Reid, M. S.; Gardner, R. A.

    1977-01-01

    Work at the Jet Propulsion Laboratory had resulted in the development of a primary absolute cavity radiometer (PACRAD), which was recently accepted as an international standard of irradiance. The development of an wall-weather, field-worthy solar radiometer based on the PACRAD is discussed, and its calibration stability over a two-year period in the field is described.

  5. Field Emission Measurements from Niobium Electrodes

    Energy Technology Data Exchange (ETDEWEB)

    M. BastaniNejad, P.A. Adderley, J. Clark, S. Covert, J. Hansknecht, C. Hernandez-Garcia, R. Mammei, M. Poelker

    2011-03-01

    Increasing the operating voltage of a DC high voltage photogun serves to minimize space charge induced emittance growth and thereby preserve electron beam brightness, however, field emission from the photogun cathode electrode can pose significant problems: constant low level field emission degrades vacuum via electron stimulated desorption which in turn reduces photocathode yield through chemical poisoning and/or ion bombardment and high levels of field emission can damage the ceramic insulator. Niobium electrodes (single crystal, large grain and fine grain) were characterized using a DC high voltage field emission test stand at maximum voltage -225kV and electric field gradient > 10MV/m. Niobium electrodes appear to be superior to diamond-paste polished stainless steel electrodes.

  6. Gravimetric Measurement of Magnetic Field Gradient Spatial Distribution

    CERN Document Server

    Arutunian, S G; Egiazarian, S L; Mailian, M R; Sinenko, I G; Sinjavski, A V; Vasiniuk, I E

    1999-01-01

    Magnetic interaction between a weighing sample and an external magnetic field allows to measure characteristics of magnetic field (a sample with known magnetic characteristics), as well as the magnetic properties of a sample (a known magnetic field). Measurement of materials magnetic permeability is a well known application of this method. In this paper we restrict ourselves to the measurement of magnetic field spatial distribution, which was achieved by scanning of samples from known materials along the vertical axis. Field measurements by Hall detector were done to calibrate obtained data. Such measurements are of great interest in some branches of physics, in particular, in accelerator physics, where the quality of magnetic system parts eventually determine the quality of accelerated bunches. Development of a simple and cheep device for measurement of magnetic field spatial distribution is an urgent problem. The developed system for gravimetric measurement of magnetic field gradients partially solves this ...

  7. About the Influence of the Magnetic Field Configuration on the Levitation Characteristics of the System Superconductor - Array of Magnets

    Science.gov (United States)

    Ermolaev, Yu. S.; Rudnev, I. A.

    2014-07-01

    Interaction of a superconductor with an array of magnets having different orientations of the magnetization vector is theoretically investigated. Based on a critical state model, the interaction force arising in the system superconductor - array of magnets is calculated by the method of finite elements. Optimal configurations of the magnetic system are established in which maximum values of both attractive and repulsive forces are created.

  8. Kaluza-Klein rotating multi-black hole configurations with electromagnetic field in Einstein-Maxwell-dilaton gravity

    CERN Document Server

    Yazadjiev, S

    2012-01-01

    We present a new solution in 5D Einstein-Maxwell-dilaton gravity describing an equilibrium configuration of extremal rotating black holes with lens space horizon topologies. The basic properties of the solution are investigated and the basic physical quantities are calculated. It is shown that the black hole horizons are superconducting in the sense that they expel the magnetic flux lines.

  9. PHASE GRADIENT METHOD OF MAGNETIC FIELD MEASUREMENTS IN ELECTRIC VEHICLES

    Directory of Open Access Journals (Sweden)

    N. G. Ptitsyna

    2013-01-01

    Full Text Available Operation of electric and hybrid vehicles demands real time magnetic field control, for instance, for fire and electromagnetic safety. The article deals with a method of magnetic field measurements onboard electric cars taking into account peculiar features of these fields. The method is based on differential methods of measurements, and minimizes the quantity of magnetic sensors.

  10. Field of Temperature Measurement by Virtual Instrumentation

    Directory of Open Access Journals (Sweden)

    Libor HARGAŠ

    2009-01-01

    Full Text Available This paper introduces about temperature determination for given dot of picture through image analysis. Heat transfer is the transition of thermal energy from a heated item to a cooler item. Main method of measurement of temperature in image is Pattern Matching, color scale detection and model detection. We can measure temperature dependency at time for selected point of thermo vision images. This measurement gives idea about the heat transfer at time dependences.

  11. Measurement of the SC magnetic field

    CERN Multimedia

    CERN PhotoLab

    1973-01-01

    The 3.5-metre-arm carrying 100 Hall plates used for the measurmeent of the SC magnetic field. The arm rotates in a horizontal plane, its positioning and the data read-out are controlled by an on-line computer.

  12. Techniques to measure complex-plane fields

    CSIR Research Space (South Africa)

    Dudley, Angela L

    2014-09-25

    Full Text Available In this work we construct coherent superpositions of Gaussian and vortex modes which can be described to occupy the complex-plane. We demonstrate how these fields can be experimentally constructed in a digital, controllable manner with a spatial...

  13. Sampling Criterion for EMC Near Field Measurements

    DEFF Research Database (Denmark)

    Franek, Ondrej; Sørensen, Morten; Ebert, Hans

    2012-01-01

    -case representative of a signal trace on a typical printed circuit board. It has been found that the sampling density derived in this way is in fact very similar to that given by the antenna near field sampling theorem, if an error less than 1 dB is required. The principal advantage of the proposed formulation is its...

  14. Impact of built-in fields and contact configuration on the characteristics of ultra-thin GaAs solar cells

    CERN Document Server

    Aeberhard, Urs

    2016-01-01

    We discuss the effects of built-in fields and contact configuration on the photovoltaic characteristics of ultrathin GaAs solar cells. The investigation is based on advanced quantum-kinetic simulations reaching beyond the standard semi-classical bulk picture concerning the consideration of charge carrier states and dynamics in complex potential profiles. The thickness dependence of dark and photocurrent in the ultra-scaled regime is related to the corresponding variation of both, the built-in electric fields and associated modification of the density of states, and the optical intensity in the films. Losses in open-circuit voltage and short-circuit current due to leakage of electronically and optically injected carriers at minority carrier contacts are investigated for different contact configurations including electron and hole blocking barrier layers. The microscopic picture of leakage currents is connected to the effect of finite surface recombination velocities in the semi-classical description, and the i...

  15. Simultaneous measurement of thermal diffusivity and effusivity of solids using the flash technique in the front-face configuration

    Science.gov (United States)

    Wilbur Pech-May, Nelson; Cifuentes, Ángel; Mendioroz, Arantza; Oleaga, Alberto; Salazar, Agustín

    2015-08-01

    Both thermal diffusivity and effusivity (or conductivity) are necessary to characterize the thermal transport properties of a material. The flash method is the most recognized procedure to measure the thermal diffusivity of free-standing opaque plates. However, it fails to simultaneously obtain the thermal effusivity (or conductivity). This is due to the difficulty of knowing the total energy absorbed by the sample surface after the light pulse. In this work, we propose using the flash method in the front-face configuration on a two-layer system made of the unknown plate and a fluid of known thermal properties. We demonstrate that the surface temperature is sensitive to the thermal mismatch between the plate and the fluid, which is governed by their thermal effusivity ratio. In order to verify the validity of the method and to establish its application limits we have performed flash measurements, using a pulsed laser and an infrared camera, on a set of calibrated materials (metals, alloys, ceramics and polymers) covering a wide range of thermal transport properties. These results confirm the ability of the flash method to simultaneously retrieve thermal diffusivity and effusivity in a fast manner in samples whose effusivities are lower than three times the effusivity of the liquid used as backing fluid.

  16. Measurement Methods in the field of benchmarking

    Directory of Open Access Journals (Sweden)

    István Szűts

    2004-05-01

    Full Text Available In benchmarking we often come across with parameters being difficultto measure while executing comparisons or analyzing performance, yet they haveto be compared and measured so as to be able to choose the best practices. Thesituation is similar in the case of complex, multidimensional evaluation as well,when the relative importance and order of different dimensions, parameters to beevaluated have to be determined or when the range of similar performanceindicators have to be decreased with regard to simpler comparisons. In suchcases we can use the ordinal or interval scales of measurement elaborated by S.S.Stevens.

  17. Measuring Propagation Speed of Coulomb Fields

    OpenAIRE

    De Sangro, R.; Finocchiaro, G.; Patteri, P.; Piccolo, M.; Pizzella, G.

    2012-01-01

    The problem of gravity propagation has been subject of discussion for quite a long time: Newton, Laplace and, in relatively more modern times, Eddington pointed out that, if gravity propagated with finite velocity, planets motion around the sun would become unstable due to a torque originating from time lag of the gravitational interactions. Such an odd behavior can be found also in electromagnetism, when one computes the propagation of the electric fields generated by a set of uniformly movi...

  18. Wave directional spreading from point field measurements

    Science.gov (United States)

    McAllister, M. L.; Venugopal, V.; Borthwick, A. G. L.

    2017-04-01

    Ocean waves have multidirectional components. Most wave measurements are taken at a single point, and so fail to capture information about the relative directions of the wave components directly. Conventional means of directional estimation require a minimum of three concurrent time series of measurements at different spatial locations in order to derive information on local directional wave spreading. Here, the relationship between wave nonlinearity and directionality is utilized to estimate local spreading without the need for multiple concurrent measurements, following Adcock & Taylor (Adcock & Taylor 2009 Proc. R. Soc. A 465, 3361-3381. (doi:10.1098/rspa.2009.0031)), with the assumption that directional spreading is frequency independent. The method is applied to measurements recorded at the North Alwyn platform in the northern North Sea, and the results compared against estimates of wave spreading by conventional measurement methods and hindcast data. Records containing freak waves were excluded. It is found that the method provides accurate estimates of wave spreading over a range of conditions experienced at North Alwyn, despite the noisy chaotic signals that characterize such ocean wave data. The results provide further confirmation that Adcock and Taylor's method is applicable to metocean data and has considerable future promise as a technique to recover estimates of wave spreading from single point wave measurement devices.

  19. Analysis of the measurement field of the optical klystron

    Institute of Scientific and Technical Information of China (English)

    2000-01-01

    The measured fields of the optical klystron in NSRL (National Sychrotron Radiation Laboratory) are given, including the distribution on the axis, and the integrated field distribution. The harmonic magnet field and the spectra of the spontaneous emission are analyzed, and the multiple field is presented by fitting the diagram. The influence of the integrated field on the close orbit of the beam and on the operation parameters of the storage ring, and the compensation in the experiment are also discussed.

  20. Precise Measurement of the Thickness of a Dielectric Layer on a Metal Surface by Use of a Modified Otto Optical Configuration

    Science.gov (United States)

    Kaneoka, Yoshiki; Nishigaki, Kentaro; Mizutani, Yasuhiro; Iwata, Tetsuo

    2015-01-01

    We propose a modified method for thickness measurement of a dielectric coating layer on metal based on Otto optical configuration (O-configuration). This method enables us to estimate the coating thickness that typically ranges from several tens of nanometers to more than one micrometer with precision less than a few nanometers. The common method to measure the thickness of dielectric coating layer is to utilize the frustrated total-internal reflection. In order to measure the thickness of several tens of nanometers, one can apply the surface-plasmon-resonance (SPR) phenomenon generated by the p-polarized light. For thickness larger than one hundred nanometers, a metal-clad leaky-waveguide (MCLW) mode generated by the p- or the s-polarized light can be employed without significant changes to the optical setup. The numerical and experimental verifications of the modified O-configuration reveals its effectiveness for precise measurement of moderately-thick dielectric coating layer on the metal.

  1. Dynamic formation of a hot field reversed configuration with improved confinement by supersonic merging of two colliding high-β compact toroids.

    Science.gov (United States)

    Binderbauer, M W; Guo, H Y; Tuszewski, M; Putvinski, S; Sevier, L; Barnes, D; Rostoker, N; Anderson, M G; Andow, R; Bonelli, L; Brandi, F; Brown, R; Bui, D Q; Bystritskii, V; Ceccherini, F; Clary, R; Cheung, A H; Conroy, K D; Deng, B H; Dettrick, S A; Douglass, J D; Feng, P; Galeotti, L; Garate, E; Giammanco, F; Glass, F J; Gornostaeva, O; Gota, H; Gupta, D; Gupta, S; Kinley, J S; Knapp, K; Korepanov, S; Hollins, M; Isakov, I; Jose, V A; Li, X L; Luo, Y; Marsili, P; Mendoza, R; Meekins, M; Mok, Y; Necas, A; Paganini, E; Pegoraro, F; Pousa-Hijos, R; Primavera, S; Ruskov, E; Qerushi, A; Schmitz, L; Schroeder, J H; Sibley, A; Smirnov, A; Song, Y; Sun, X; Thompson, M C; Van Drie, A D; Walters, J K; Wyman, M D

    2010-07-23

    A hot stable field-reversed configuration (FRC) has been produced in the C-2 experiment by colliding and merging two high-β plasmoids preformed by the dynamic version of field-reversed θ-pinch technology. The merging process exhibits the highest poloidal flux amplification obtained in a magnetic confinement system (over tenfold increase). Most of the kinetic energy is converted into thermal energy with total temperature (T{i}+T{e}) exceeding 0.5 keV. The final FRC state exhibits a record FRC lifetime with flux confinement approaching classical values. These findings should have significant implications for fusion research and the physics of magnetic reconnection.

  2. Gradio - Earth gravity field measurement on Aristoteles

    Science.gov (United States)

    Pawlak, D.; Meyer, Ph.; Bernard, A.; Touboul, P.

    1991-10-01

    The design and operation of Gradio, the instrument that was specifically designed for precise gradiometry measurements during the Aristoteles mission, are described. The Gradio is based on simultaneous measurements by four three-axis ultrasensitive accelerometers performed in several locations on a rigid stable structure, called gradio plate, which are then used to compute g gradients. The operational phase of Gradio will last 6 months; the orbit will be circular, near polar, and heliosynchronous, at an altitude of 200 km. It is estimated that Gradio will measure the two main components T(yy) and T(zz) of the gravity gradient tensor in the (0.005, 0.125) Hz frequency bandwidth with an accuracy of 0.01 E.U.

  3. Table 1. Summary of Field Testing and Measurement Data

    Data.gov (United States)

    U.S. Environmental Protection Agency — Key performance parameters measured during the field demonstration such as lining thickness, compressive strength, Flexural Strength, Modulus of Elasticity, bond...

  4. Measuring the effect of field viability on wheat yield

    DEFF Research Database (Denmark)

    Olsen, Jakob Vesterlund; Schou, Jesper Sølver

    showing a significant effect on yields. Further research may involve estimating the effect of field characteristics on the aggregated economic farm performance. The field viability index has multiple applications in e.g. benchmarking, leasing or buying arrangements, and for identifying potential land...... contributes by introducing a new joint index for field shape and field size, field viability index (FVI), aiming at measuring the effect of land fragmentation on farm performance based on field characteristics. The index is calculated for Danish wheat fields and is tested on a large sample of Danish farmers...

  5. Measurements of SNAC2 area dosimeters placed in different configurations around the PROSPERO reactor and comparison with TRIPOLI-4 calculations

    Energy Technology Data Exchange (ETDEWEB)

    Rousseau, G.; Chambru, L.; Authier, N. [CEA, Centre de Valduc, 21120 Is-sur-Tille, (France)

    2015-07-01

    In the context of criticality accident alarm system tests, several experiments were carried out in 2013 on the PROSPERO reactor to study the response to neutron and gamma of different devices and dosimeters, particularly on the SNAC2 dosimeter. This article presents the results of this criticality dosimeter in different configurations, and compares the experimental measurements with the results of calculation performed with the TRIPOLI-4 Monte-Carlo Neutral Particles transport code. PROSPERO is a metallic critical assembly managed by the Criticality, Neutron Science and Measurement Department located at the French CEA Research Center of Valduc. The core, surrounded by a reflector of depleted uranium, is composed of 2 horizontal cylindrical blocks made of a highly enriched uranium alloy which can be placed in contact, and of 4 depleted uranium control rods which allow the reactor to be driven. This reactor, placed in a cell 10 m x 8 m x 6 m high, with 1.4-meter-thick concrete walls, is used as a fast neutron spectrum source and is operated at stable power level in delayed critical state, which can vary from 3 mW to 3 kW. PROSPERO is extensively used for electronic hardening or to study the effect of the neutrons on various materials. The SNAC2 criticality dosimeter is a zone dosimeter allowing the off line measurement of criticality accident neutron doses. This dosimeter consists of the pile up of seven activation foils embedded into a 23 mm diameter x 21 mm height cadmium container. The activation measurement of each foil, using a gamma spectroscopy technique, gives information about the neutron reaction rates. The SNAC2 software allows the spectrum unfolding from these values, taking into account the hypothesis of a particular spectrum shape, in three components: a Maxwell spectrum component for the thermal range, a 1/E component for the epithermal range, and a Watt spectrum component for the high energy range. Moreover, from the neutron spectrum, the SNAC

  6. Principles of planar near-field antenna measurements

    CERN Document Server

    Gregson, Stuart; Parini, Clive

    2007-01-01

    This single volume provides a comprehensive introduction and explanation of both the theory and practice of 'Planar Near-Field Antenna Measurement' from its basic postulates and assumptions, to the intricacies of its deployment in complex and demanding measurement scenarios.

  7. Field measurement and analysis of harmonic levels

    Energy Technology Data Exchange (ETDEWEB)

    Karunakara, K.; Muthu Kumar, E.; Rajesh Kumar, O.; Nambudiri, P.V.V.; Srinivasan, K.N. [Central Power Research Institute, Bangalore (India)

    1999-07-01

    The level of harmonics on the transmission and distribution network is rising over the years, due to the rapid development and usage of electronic and semiconductor devices in the industries, as these devices produce harmonic currents. As the harmonic currents produced by these devices are unproductive and affect the ideal sinusoidal waveshapes, these have to be limited to a tolerable limit at the Point of Common Coupling (PCC). Before setting a tolerable limit on harmonics it is necessary to know the level of harmonics already present in the system, so that the limits suggested are comprehensive and practicable. To have a fair idea about the current and voltage harmonics on the Indian system, Central Power Research Institute (CPRI) has carried out a lot of measurements both on the distribution network and transmission network over the past 13 years. This paper discusses the harmonic measurements carried out by CPRI on different loads and voltage levels on the Indian network. The methodology adopted for measurement and results are also discussed in this paper. (author)

  8. Side abutment pressure distribution by field measurement

    Institute of Scientific and Technical Information of China (English)

    WANG Lian-guo; SONG Yang; HE Xing-hua; ZHANG Jian

    2008-01-01

    Given the 7123 working face in the Qidong Coal Mine of the Wanbei Mining Group, nine dynamic roof monitors were installed in the crossheading to measure the amount and velocity of roof convergence in different positions and at different times and three steel bored stress sensors were installed in the return airway to measure rock stress at depth. On the basis of this arrangement, the rule of change of the distribution of the side abutment pressure with the advance of the working face and movement of overlying strata was studied. The rule of change and the stability of rock stress at depth were measured. Secondly, the affected area and stability time of the side abutment pressure were also studied. The results show that: 1) During working, the face advanced distance was from 157 m to 99 m, the process was not effected by mining induced pressure. When the distance was 82 m, the position of peak stress was 5 m away from the coal wall. When the distance was 37 m, the position of peak stress away from the coal wall was about 15 m to 20 m and finally reached a steady state; 2) the time and the range of the peak of side rock pressure obtained from stress sensors were consistent with the results from the dynamic roof monitors; 3) the position of the peak pressure was 25 m away from the coal wall.

  9. Lamb-shift and electric field measurements in plasmas

    Science.gov (United States)

    Doveil, F.; Chérigier-Kovacic, L.; Ström, P.

    2017-01-01

    The electric field is a quantity of particular relevance in plasma physics. Indeed, its fluctuations are responsible for different macroscopic phenomena such as anomalous transport in fusion plasmas. Answering a long-standing challenge, we offer a new method to locally and non-intrusively measure weak electric fields and their fluctuations in plasmas, by means of a beam of hydrogen ions or atoms. We present measurements of the electric field in vacuum and in a plasma where Debye shielding is measured. For the first time, we have used the Lamb-shift resonance to measure oscillating electric fields around 1 GHz and observed the strong enhancement of the Lyman-α signal. The measurement is both direct and non-intrusive. This method provides sensitivity (mV cm-1) and temporal resolution (ns) that are three orders higher compared to current diagnostics. It thus allows measuring fluctuations of the electric field at scales not previously reached experimentally.

  10. Measuring the Earth's Magnetic Field in a Laboratory

    Science.gov (United States)

    Cartacci, A.; Straulino, S.

    2008-01-01

    Two methods for measuring the Earth's magnetic field are described. In the former, according to Gauss, the Earth's magnetic field is compared with that of a permanent magnet; in the latter, a well-known method, the comparison is made with the magnetic field generated by a current. As all the used instruments are available off the shelf, both…

  11. Measurement of the magnetic-field parameters of the NICA Booster dipole magnet

    Science.gov (United States)

    Kostromin, S. A.; Borisov, V. V.; Bichkov, A. V.; Golubitsky, O. M.; Donyagin, A. N.; Morozov, N. A.; Samsonov, E. V.; Omelyanenko, M. M.; Khodzhibagiyan, H. G.; Shemchuk, A. V.

    2016-12-01

    Serial assembly and tests of dipole and quadrupole magnets of the NICA Booster have started at the Laboratory of High Energy Physics of the Joint Institute for Nuclear Research (JINR). The accelerator is fitted with Nuclotron-type magnets with a superconducting winding and an iron yoke for shaping the needed magnetic field. The design of magnets for NICA was optimized (based on the experience gained in constructing and operating the JINR Nuclotron) for the production of magnetic fields of the required configuration in terms of the beam dynamics in the accelerator and the collider. Measurements of parameters of the field of each magnet are expected to be performed in the process of assembly and testing of each module of the magnet-cryostat system of the NICA Booster and Collider. The results of magnetic measurements for the NICA Booster dipole magnet are presented.

  12. Microwave field measurement via Rabi resonances in Cs atoms

    CERN Document Server

    Sun, Fuyu; Bai, Qingsong; Huang, Xianhe; Ma, Jie; Li, Xiaofeng

    2016-01-01

    We present a technique for measuring microwave (MW) field based on Rabi resonances induced by the interaction of atoms with a phase-modulated MW field. A theoretical model of field measurement is used to calculate Rabi frequency. Single-peak feature of the measurement model makes the technique a valuable tool for simple and fast field measurement. As an example, we use the technique to determine the MW field strength inside a Cs vapor cell in the X-band rectangular cavity for applied power in the range of -21 dBm to 20 dBm. The results show that this proposed technique is capable for detecting the field over a broad dynamical range.

  13. Measurement of Temperature Fields in Long Span Concrete Bridges

    Directory of Open Access Journals (Sweden)

    J. Římal

    2001-01-01

    Full Text Available This paper deals with assesing of the influence of climate temperatures on deformations and stresses in a cross section of the Nusle Bridge. The main purpose is to describe the measurement of the thermal fields, to compare measured and computed temperature fields, and to provide a real estimation of the stresses that occur.

  14. Infrared measurement and simulation of magnesium alloy welding temperature field

    Institute of Scientific and Technical Information of China (English)

    LIU Liming; CHI Mingsheng; HUANG Ruisheng; SONG Gang; ZHOU Yang

    2005-01-01

    The welding temperature field of magnesium alloy AZ31 welded by TIG was measured with the uncooled infrared (IR) thermal imaging technology. The variables in the mathematic mode of welding temperature fields were revised by IR temperature data. Based on the results of simulation, the loss of temperature fields caused by arc interfered was compensated, and a whole temperature field was achieved, which provided a precise and powerful foundation for the investigation of microstructure of the joints.

  15. Measurement of electric fields and estimation of dielectric susceptibility

    Science.gov (United States)

    Nogi, Yasuyuki; Suzuki, Kiyomitsu; Ohkuma, Yasunori

    2013-05-01

    We describe a method of measuring the spatial structures of electric fields produced by charge distributions such as those on strip electrodes, small disk electrodes, and long double-plate electrodes. An electric-field sensor with high sensitivity to ac fields is fabricated for the measurement using a thin copper sheet. The reliability of the sensor is confirmed using a parallel-plate capacitor. The electric fields are oscillated at a frequency of 300 kHz to operate the electric-field sensor successfully. The structures of the measured fields coincide well with those of theoretical fields derived from Coulomb's law. When a dielectric is inserted in an electric field, polarization charges appear on the surface of the dielectric and modify the electric field in empty space. We measure the modified field and confirm the well-known linear relation between the polarization of a dielectric and the electric field. Dielectric susceptibilities are estimated from the linear relation for four types of dielectric.

  16. Stereoscopic PIV measurements of the flow field in a turbine cascade

    Science.gov (United States)

    Tian, Yangtao; Ma, Hongwei; Ma, Rong

    2017-02-01

    This paper presents experimental measurements of the flow field in a Low-speed Turbine Cascade using a stereoscopic particle-image velocimetry (SPIV). During the measurements, a pair of frame-straddling-based CCD cameras were configured at different sides of the laser light sheet, and appropriate tracing particles (DEHS) were employed. The measurements were conducted at the incidence angle of 0 degree and exit Reynolds number of 1.7 × 105 with the tip clearance 1.18% of blade chord. The tip flow features, such as the evolution and breakdown of tip leakage vortex, the horseshoe vortex, turbulence characteristics of tip leakage flow, were studied for the flow field analysis. The results showed that the tip leakage flow/vortex mainly dominate flow fields in the tip region. The tip leakage vortex performs as a concentrated vortex before its breaking down and splitting into small vortices. The highest turbulence intensity mainly occurs in the tip region along with the trajectory of tip leakage vortex, and when the vortex breaks down, the turbulence intensity reduces rapidly. Additionally, the SPIV with this configuration also shows an advantage in investigating the flow structures and mechanism inside the turbine cascade.

  17. Analytical measures of homogeneity of the photon radiation field and possible applications

    Science.gov (United States)

    Lukan, Junoš; Ambrožič, Klemen; Žerovnik, Gašper; Snoj, Luka

    2017-08-01

    For many practical applications, homogeneity of a field, whether neutron or electromagnetic, is of significance. Definitions of homogeneity or its calculation are diverse in the existing literature, however. This paper is an attempt to explore the concept of homogeneity and the ways it can be measured or calculated. The list of the measures that were considered includes: the ratio between the maximum and the minimum value, the ratio between the maximum difference and the mean value, the variance of the field and its generalization, and the mean and the variance of the field's gradient. These were applied to a realistic gamma-ray irradiation scenario, both by deriving a semi-analytical approximation and in a Monte Carlo numerical simulation. The irradiation arrangement included a hollow cylindrical irradiation channel and different numbers of spent fuel elements taken from a TRIGA reactor. By manipulating the geometry of this setup, fields of varying degrees of homogeneity were simulated and the homogeneity measures were calculated. By applying principal component analysis the maximum value to the weighted mean ratio was put forth as the most desirable measure. Finally, the application of this measure was demonstrated by choosing one of the irradiation configurations previously considered that produced a homogeneous gamma-ray field.

  18. New Limits on Extragalactic Magnetic Fields from Rotation Measures

    Science.gov (United States)

    Pshirkov, M. S.; Tinyakov, P. G.; Urban, F. R.

    2016-05-01

    We take advantage of the wealth of rotation measures data contained in the NRAO VLA Sky Survey catalog to derive new, statistically robust, upper limits on the strength of extragalactic magnetic fields. We simulate the extragalactic magnetic field contribution to the rotation measures for a given field strength and correlation length, by assuming that the electron density follows the distribution of Lyman-α clouds. Based on the observation that rotation measures from distant radio sources do not exhibit any trend with redshift, while the extragalactic contribution instead grows with distance, we constrain fields with Jeans' length coherence length to be below 1.7 nG at the 2 σ level, and fields coherent across the entire observable Universe below 0.65 nG. These limits do not depend on the particular origin of these cosmological fields.

  19. [A focused sound field measurement system by LabVIEW].

    Science.gov (United States)

    Jiang, Zhan; Bai, Jingfeng; Yu, Ying

    2014-05-01

    In this paper, according to the requirement of the focused sound field measurement, a focused sound field measurement system was established based on the LabVIEW virtual instrument platform. The system can automatically search the focus position of the sound field, and adjust the scanning path according to the size of the focal region. Three-dimensional sound field scanning time reduced from 888 hours in uniform step to 9.25 hours in variable step. The efficiency of the focused sound field measurement was improved. There is a certain deviation between measurement results and theoretical calculation results. Focal plane--6 dB width difference rate was 3.691%, the beam axis--6 dB length differences rate was 12.937%.

  20. Measures and dimensions of fractal sets in local fields

    Institute of Scientific and Technical Information of China (English)

    QIU Hua; SU Weiyi

    2006-01-01

    The study of fractal analysis over the local fields as underline spaces is very important since it can motivate new approaches and new ideas, and discover new techniques in the study of fractals. To study fractal sets in a local field K, in this paper, we define several kinds of fractal measures and dimensions of subsets in K. Some typical fractal sets in K are constructed. We also give out the Hausdorff dimensions and measures, Box-counting dimensions and Packing dimensions, and stress that there exist differences between fractal analysis on local fields and Euclidean spaces. Consequently, the theoretical foundation of fractal analysis on local fields is established.

  1. Hypertext Configurations

    DEFF Research Database (Denmark)

    Finnemann, Niels Ole

    2016-01-01

    , links, interactive processes, and time scalings, and that the hypertext configuration is a major but not sole source of the messiness of big data. The notion of hypertext will be revalidated, placed at the center of the interpretation of networked digital media, and used in the analysis of the fast...

  2. Strain Measurement on the Toroidal Field (TF) Coil Cases

    Institute of Scientific and Technical Information of China (English)

    Chen Zhuomin; Long Feng; Wu Hao

    2005-01-01

    The stress-strain state of the structure is a matter of interest to designer. The strain measurement of superconducting magnets at cryogenic temperature is a specific technique. Based on strain measurement of TF coil case for EAST, this paper presents a measuring technique at cryogenic temperature and on intense magnetic field. The compensation methods for both temperature and magnetic field effects of the gauges, together with the measured results are involved, and the discussions of the measured results are given in the paper.

  3. Measurement of the Waveguide Near-field Optical Spot

    Institute of Scientific and Technical Information of China (English)

    2003-01-01

    The characteristic of near-field spots is analyzed.The size of the near field and the heat response time of the hybrid record medium to overcome super paramagnetic effect are calculated based on the heat transfer theory. A novel measuring method for the diameter of near-field recording spot is also presented. Since the grain of the recording media is tiny enough,near-field optical lithography can be accomplished with the aid of atomic force microscope (AFM).The diameter of near-field recording spot can be obtained by specifically designed computer.So the relationship between the near-field recording spot diameter and the probe size of near-field recording system, the near field recording distance coupling between head and disc can be got.

  4. Measuring Oscillatory Velocity Fields Due to Swimming Algae

    CERN Document Server

    Guasto, Jeffrey S; Gollub, J P

    2010-01-01

    In this fluid dynamics video, we present the first time-resolved measurements of the oscillatory velocity field induced by swimming unicellular microorganisms. Confinement of the green alga C. reinhardtii in stabilized thin liquid films allows simultaneous tracking of cells and tracer particles. The measured velocity field reveals complex time-dependent flow structures, and scales inversely with distance. The instantaneous mechanical power generated by the cells is measured from the velocity fields and peaks at 15 fW. The dissipation per cycle is more than four times what steady swimming would require.

  5. Electro-optic probe measurements of electric fields in plasmas

    Science.gov (United States)

    Nishiura, M.; Yoshida, Z.; Mushiake, T.; Kawazura, Y.; Osawa, R.; Fujinami, K.; Yano, Y.; Saitoh, H.; Yamasaki, M.; Kashyap, A.; Takahashi, N.; Nakatsuka, M.; Fukuyama, A.

    2017-02-01

    The direct measurements of high-frequency electric fields in a plasma bring about significant advances in the physics and engineering of various waves. We have developed an electro-optic sensor system based on the Pockels effect. Since the signal is transmitted through an optical fiber, the system has high tolerance for electromagnetic noises. To demonstrate its applicability to plasma experiments, we report the first result of measurement of the ion-cyclotron wave excited in the RT-1 magnetosphere device. This study compares the results of experimental field measurements with simulation results of electric fields in plasmas.

  6. Magnetic rotation imaging method to measure the geomagnetic field

    Institute of Scientific and Technical Information of China (English)

    2008-01-01

    A new imaging method for measuring the geomagnetic field based on the magnetic rotation effect is put forward. With the help of polarization property of the sunlight reflected from the ground and the magnetic rotation of the atmosphere, the geomagnetic field can be measured by an optical system installed on a satellite. According to its principle, the three-dimensional image of the geomagnetic field can be obtained. The measuring speed of this method is very high, and there is no blind spot and distortion. In this paper, the principle of this method is presented, and some key problems are discussed.

  7. Gauge-invariant functional measure for gauge fields on CP2

    Science.gov (United States)

    Nair, V. P.

    2013-11-01

    We introduce a general parametrization for non-Abelian gauge fields on the four-dimensional space CP2. The volume element for the gauge-orbit space or the space of physical configurations is then investigated. The leading divergence in this volume element is obtained in terms of a higher dimensional Wess-Zumino-Witten action, which has previously been studied in the context of Kähler-Chern-Simons theories. This term, it is argued, implies that one needs to introduce a dimensional parameter to specify the integration measure, a step which is a nonperturbative version of the well-known dimensional transmutation in four-dimensional gauge theories.

  8. Direct analysis of dispersive wave fields from near-field pressure measurements

    NARCIS (Netherlands)

    Horchens, L.

    2011-01-01

    Flexural waves play a significant role for the radiation of sound from plates. The analysis of flexural wave fields enables the detection of sources and transmission paths in plate-like structures. The measurement of these wave fields can be carried out indirectly by means of near-field acoustic hol

  9. Dynamics measured in a non-Archimedean field

    NARCIS (Netherlands)

    Kool, J.

    2012-01-01

    We study dynamical systems using measures taking values in a non-Archimedean field. The underlying space for such measure is a zero-dimensional topological space. In this paper we elaborate on the natural translation of several notions, e.g., probability measures, isomorphic transformations, entropy

  10. Large eddy simulation of the unsteady flow-field in an idealized human mouth-throat configuration.

    Science.gov (United States)

    Cui, X G; Gutheil, E

    2011-11-10

    The present study concerns the simulation and analysis of the flow field in the upper human respiratory system in order to gain an improved understanding of the complex flow field with respect to the process affecting drug delivery for medical treatment of the human air system. For this purpose, large eddy simulation (LES) is chosen because of its powerful performance in the transitional range of laminar and turbulent flow fields. The average gas velocity in a constricted tube is compared with experimental data (Ahmed and Giddens, 1983) and numerical data from Reynolds-averaged Navier-Stokes (RANS) equations coupled with low Reynolds number (LRN) κ-ω model (Zhang and Kleinstreuer, 2003) and LRN shear-stress transport κ-ω model (Jayaraju et al., 2007), for model validation. The present study emphasizes on the instantaneous flow field, where the simulations capture different scales of secondary vortices in different flow zones including recirculation zones, the laryngeal jet zone, the mixing zone, and the wall shear layer. It is observed that the laryngeal jet tail breaks up, and the unsteady motion of laryngeal jet is coupled with the unsteady distribution of secondary vortices in the jet boundary. The present results show that it is essential to study the unsteady flow field since it strongly affects the particle flow in the human upper respiratory system associated with drug delivery for medical treatment.

  11. Toroidal configuration of the orbit of the electron of the hydrogen atom under strong external magnetic fields

    OpenAIRE

    Aringazin, A. K.

    2002-01-01

    In this paper we overview some results on the hydrogen atom in external static uniform magnetic fields. We focus on the case of very strong magnetic field, B>>B_0=2.3x10^9 Gauss, use various approximate models and, particularly, in the adiabatic approximation have calculated exactly the integral defining the effective potential. This potential appears to be finite at z=0. Our consideration of the problem of highly magnetized atoms and molecules is motivated by the recently developed MagneGas ...

  12. Multi-configuration electromagnetic induction measurements at long term agricultural test sites in Germany with different fertilizer and irrigation managements

    Science.gov (United States)

    Kaufmann, Manuela Sarah; von Hebel, Christian; Brogi, Cosimo; Baumecker, Michael; Döring, Thomas; Amelung, Wulf; Vereecken, Harry; van der Kruk, Jan

    2017-04-01

    Electromagnetic induction (EMI) data are often being used to investigate large scale soil properties including clay content, soil water content, and salinity changes for a wide range of applications. For agricultural sites, different management practices such as organic/mineral fertilization, tillage, and/or irrigation are important when interpreting the measured apparent electrical conductivity (ECa). Here, we present EMI data recorded at two long term field experiment (LTFE) agricultural test sites in Thyrow near Berlin (Germany), where different long term fertilizer and irrigation management practices were applied. We used two fixed-boom multi-coil EMI instruments that simultaneously measure over nine different depths of investigation (DOI), recording information ranging between the very shallow (0-0.25 m) ploughing zone including the organic matter and the surface soil (A-Horizon) down to the relatively deep (0-2.7 m) subsoil (B-Horizon) or even substratum (C-Horizon). At both test sites, the prevailing sandy to silty sand in the A- and B-Horizon is underlain by a glacial till C-Horizon resulting in generally low ECa values between 0.5 and 5 mS/m. At one test site, a "static nutrient deficiency experiment" is performed since 1937, where organic fertilizer (farm yard manure) and mineral fertilizers (nitrogen-phosphate-potassium (NPK) and liming) are applied at specific grids. Comparing the fertilizer application grid to the measured EMI data, the lowest ECa values coincide to unfertilized grids whereas the ECa values increase with liming, farm yard manure, and NPK. The visually observed correlation between ECa and the liming treatment was possibly due to the increased pH of the soil, because the fertilizer application increases ion contents that increase the soil electrical conductivity. At the second test site, a "Static Irrigation and Fertilizer Experiment" is conducted, where next to the fertilizer treatment (farm yard manure and nitrogen) part of the field

  13. New limits on extragalactic magnetic fields from rotation measures

    CERN Document Server

    Pshirkov, Maxim S; Urban, Federico R

    2015-01-01

    We take advantage of the wealth of rotation measures data contained in the NVSS catalogue to derive new, statistically robust, upper limits on the strength of extragalactic magnetic fields. We simulate the extragalactic contribution to the rotation measures for a given field strength and correlation length, by assuming that the electron density follows the distribution of Lyman-$\\alpha$ clouds. Based on the observation that rotation measures from low-luminosity distant radio sources do not exhibit any trend with redshift, while the extragalactic contribution instead grows with distance, we constrain fields with Mpc coherence length to be below 1.2 nG at the $2\\sigma$ level, and fields coherent across the entire observable Universe below 0.5 nG. These limits do not depend on the particular origin of these cosmological fields.

  14. A method for longitudinal relaxation time measurement in inhomogeneous fields

    Science.gov (United States)

    Chen, Hao; Cai, Shuhui; Chen, Zhong

    2017-08-01

    The spin-lattice relaxation time (T1) plays a crucial role in the study of spin dynamics, signal optimization and data quantification. However, the measurement of chemical shift-specific T1 constants is hampered by the magnetic field inhomogeneity due to poorly shimmed external magnetic fields or intrinsic magnetic susceptibility heterogeneity in samples. In this study, we present a new protocol to determine chemical shift-specific T1 constants in inhomogeneous fields. Based on intermolecular double-quantum coherences, the new method can resolve overlapped peaks in inhomogeneous fields. The measurement results are in consistent with the measurements in homogeneous fields using the conventional method. Since spatial encoding technique is involved, the experimental time for the new method is very close to that for the conventional method. With the aid of T1 knowledge, some concealed information can be exploited by T1 weighting experiments.

  15. Integrated optical waveguide sensor for lighting impulse electric field measurement

    Science.gov (United States)

    Zhang, Jiahong; Chen, Fushen; Sun, Bao; Chen, Kaixin

    2014-09-01

    A Lithium niobate (LiNbO3) based integrated optical E-field sensor with an optical waveguide Mach-Zehnder interferometer (MZI) and a tapered antenna has been designed and fabricated for the measurement of the pulsed electric field. The minimum detectable E-field of the sensor was 10 kV/m. The sensor showed a good linear characteristic while the input E-fields varied from 10 kV/m to 370 kV/m. Furthermore, the maximum detectable E-field of the sensor, which could be calculated from the sensor input/output characteristic, was approximately equal to 1000 kV/m. All these results suggest that such sensor can be used for the measurement of the lighting impulse electric field.

  16. 47 CFR 73.686 - Field strength measurements.

    Science.gov (United States)

    2010-10-01

    ..., or a graph on which the distribution of measured field strength values is plotted. (vi) A list of... be submitted. (iv) A list of calibrated equipment used in the field strength survey, which, for each... equipment calibration and elevation of the antenna, a check is made to determine whether the...

  17. Solar Energetic Particle Events in the 23rd Solar Cycle: Interplanetary Magnetic Field Configuration and Statistical Relationship with Flares and CMEs

    CERN Document Server

    Miteva, R; Malandraki, O; Dorrian, G

    2014-01-01

    We study the influence of the large-scale interplanetary magnetic field configuration on the solar energetic particles (SEPs) as detected at different satellites near Earth and on the correlation of their peak intensities with the parent solar activity. We selected SEP events associated with X and M-class flares at western longitudes, in order to ensure good magnetic connection to Earth. These events were classified into two categories according to the global interplanetary magnetic field (IMF) configuration present during the SEP propagation to 1AU: standard solar wind or interplanetary coronal mass ejections (ICMEs). Our analysis shows that around 20% of all particle events are detected when the spacecraft is immersed in an ICME. The correlation of the peak particle intensity with the projected speed of the SEP-associated coronal mass ejection is similar in the two IMF categories of proton and electron events, $\\approx 0.6$. The SEP events within ICMEs show stronger correlation between the peak proton inten...

  18. Beyond mean-field dynamics of ultra-cold bosonic atoms in higher dimensions: facing the challenges with a multi-configurational approach

    Science.gov (United States)

    Bolsinger, V. J.; Krönke, S.; Schmelcher, P.

    2017-02-01

    Exploring the impact of dimensionality on the quantum dynamics of interacting bosons in traps including particle correlations is an interesting but challenging task. Due to the different participating length scales, the modelling of the short-range interactions in three dimensions plays a special role. We review different approaches for the latter and elaborate that for multi-configurational computational strategies, finite-range potentials are adequate resulting in the need for large grids to resolve the relevant length scales. This results in computational challenges, which include the exponential scaling of complexity with the number of atoms. We show that the recently developed ab initio multi-layer multi-configurational time-dependent Hartee method for bosons (ML-MCTDHB) (2013 J. Chem. Phys. 139 134103) can face both numerical challenges and present an efficient numerical implementation of ML-MCTDHB in three spatial dimensions, particularly suited to describe the quantum dynamics for elongated traps. The beneficial scaling of our approach is demonstrated by studying the tunnelling dynamics of bosonic ensembles in a double well. Comparing three-dimensional with quasi-one dimensional simulations, we find dimensionality-induced effects in the density. Furthermore, we study the crossover from weak transversal confinement, where a mean-field description of the system is sufficient, towards tight transversal confinement, where particle correlations and beyond mean-field effects are pronounced.

  19. Hypertext Configurations

    DEFF Research Database (Denmark)

    Finnemann, Niels Ole

    2016-01-01

    , links, interactive processes, and time scalings, and that the hypertext configuration is a major but not sole source of the messiness of big data. The notion of hypertext will be revalidated, placed at the center of the interpretation of networked digital media, and used in the analysis of the fast......The article presents a conceptual framework for distinguishing different sorts of heterogeneous digital materials. The hypothesis is that a wide range of heterogeneous data resources can be characterized and classified due to their particular configurations of hypertext features such as scripts......-growing amounts of heterogeneous digital collections, assemblages, and corpora. The introduction summarizes the wider background of a fast-changing data landscape....

  20. Configuration mixing of mean-field wave functions projected on angular momentum and particle number: Application to sup 2 sup 4 Mg

    CERN Document Server

    Valor, A; Bonche, P

    2000-01-01

    We present in this paper the general framework of a method which permits to restore the rotational and particle number symmetries of wave functions obtained in Skyrme HF + BCS calculations. This restoration is nothing but a projection of mean-field intrinsic wave functions onto good particle number and good angular momentum. The method allows us also to mix projected wave functions. Such a configuration mixing is discussed for sets of HF + BCS intrinsic states generated in constrained calculations with suitable collective variables. This procedure gives collective states which are eigenstates of the particle number and the angular momentum operators and between which transition probabilities are calculated. An application to sup 2 sup 4 Mg is presented, with mean-field wave functions generated by axial quadrupole constraints. Theoretical spectra and transition probabilities are compared to the experiment.

  1. Study of fault configuration related mysteries through multi seismic attribute analysis technique in Zamzama gas field area, southern Indus Basin, Pakistan

    Directory of Open Access Journals (Sweden)

    Shabeer Ahmed Abbasi

    2016-03-01

    Full Text Available Seismic attribute analysis approach has been applied for the interpretation and identification of fault geometry of Zamzama Gas Field. Zamzama gas field area, which lies in the vicinity of Kirthar fold and thrust belt, Southern Indus Basin of Pakistan. The Zamzama fault and its related structure have been predicted by applying the Average Energy Attribute, Instantaneous Frequency Attribute, relative Acoustic Impedance Attribute and Chaotic Reflection Attribute on the seismic line GHPK98A.34. The results have been confirmed by applying the spectral decomposition attribute on the same seismic line that reveal the geometric configuration of Zamzama structure. The fault is reverse and started from 0 s and ended at the depth of 2.5 s on the vertical seismic section. Hanging wall moves up along the fault plane under the action of eastward oriented stress, which formed a large north–south oriented and eastward verging thrusted anticline.

  2. Antenna gain measurements in the intermediate-field zone

    Science.gov (United States)

    Anchidin, Liliana; Bari, Farida; Dumitrascu, Ana; Paun, Mirel; Deacu, Daniela; Tasu, Sorin; Danisor, Alin; Tamas, Razvan D.

    2016-12-01

    Antenna gain is usually evaluated under far-field conditions. Furthermore, Friis transmission formula can solely be applied when antenna size can be neglected with respect to the distance between the measuring antenna and the antenna under test. In this paper, we show that by applying the distance averaging technique the far-field and antenna size constraints can be overcome. Our method was validated by measuring a monopole antenna and a Vivaldi antenna in an open area test site (OATS).

  3. First measurements of error fields on W7-X using flux surface mapping

    Science.gov (United States)

    Lazerson, Samuel A.; Otte, Matthias; Bozhenkov, Sergey; Biedermann, Christoph; Pedersen, Thomas Sunn; the W7-X Team

    2016-10-01

    Error fields have been detected and quantified using the flux surface mapping diagnostic system on Wendelstein 7-X (W7-X). A low-field ‘{\\rlap- \\iota} =1/2 ’ magnetic configuration ({\\rlap- \\iota} =\\iota /2π ), sensitive to error fields, was developed in order to detect their presence using the flux surface mapping diagnostic. In this configuration, a vacuum flux surface with rotational transform of n/m  =  1/2 is created at the mid-radius of the vacuum flux surfaces. If no error fields are present a vanishingly small n/m  =  5/10 island chain should be present. Modeling indicates that if an n  =  1 perturbing field is applied by the trim coils, a large n/m  =  1/2 island chain will be opened. This island chain is used to create a perturbation large enough to be imaged by the diagnostic. Phase and amplitude scans of the applied field allow the measurement of a small ∼ 0.04 m intrinsic island chain with a {{130}\\circ} phase relative to the first module of the W7-X experiment. These error fields are determined to be small and easily correctable by the trim coil system. Notice: This manuscript has been authored by Princeton University under Contract Number DE-AC02-09CH11466 with the U.S. Department of Energy. The publisher, by accepting the article for publication acknowledges, that the United States Government retains a non-exclusive, paid-up, irrevocable, world-wide license to publish or reproduce the published form of this manuscript, or allow others to do so, for United States Government purposes.

  4. The Virtual Fields Method Extracting Constitutive Mechanical Parameters from Full-field Deformation Measurements

    CERN Document Server

    Pierron, Fabrice

    2012-01-01

    The Virtual Fields Method: Extracting Constitutive Mechanical Parameters from Full-field Deformation Measurements is the first book on the Virtual Fields Method (VFM), a technique to identify materials mechanical properties from full-field measurements. Firmly rooted with extensive theoretical description of the method, the book presents numerous examples of application to a wide range of materials (composites, metals, welds, biomaterials) and situations (static, vibration, high strain rate). The authors give a detailed training section with examples of progressive difficulty to lead the reader to program the VFM and include a set of commented Matlab programs as well as GUI Matlab-based software for more general situations. The Virtual Fields Method: Extracting Constitutive Mechanical Parameters from Full-field Deformation Measurements is an ideal book for researchers, engineers, and students interested in applying the VFM to new situations motivated by their research.  

  5. Measurement of velocity field in parametrically excited solitary waves

    CERN Document Server

    Gordillo, Leonardo

    2014-01-01

    Paramerically excited solitary waves emerge as localized structures in high-aspect-ratio free surfaces subject to vertical vibrations. Herein, we provide the first experimental characterization of the hydrodynamics of thess waves using Particle Image Velocimetry. We show that the underlying velocity field of parametrically excited solitary waves is mainly composed by an oscillatory velocity field. Our results confirm the accuracy of Hamiltonian models with added dissipation in describing this field. Remarkably, our measurements also uncover the onset of a streaming velocity field which is shown to be as important as other crucial nonlinear terms in the current theory. The observed streaming pattern is particularly interesting due to the presence of oscillatory meniscii.

  6. Interfacial band configuration and electrical properties of LaAlO3/Al2O3/hydrogenated-diamond metal-oxide-semiconductor field effect transistors

    Science.gov (United States)

    Liu, J. W.; Liao, M. Y.; Imura, M.; Oosato, H.; Watanabe, E.; Tanaka, A.; Iwai, H.; Koide, Y.

    2013-08-01

    In order to search a gate dielectric with high permittivity on hydrogenated-diamond (H-diamond), LaAlO3 films with thin Al2O3 buffer layers are fabricated on the H-diamond epilayers by sputtering-deposition (SD) and atomic layer deposition (ALD) techniques, respectively. Interfacial band configuration and electrical properties of the SD-LaAlO3/ALD-Al2O3/H-diamond metal-oxide-semiconductor field effect transistors (MOSFETs) with gate lengths of 10, 20, and 30 μm have been investigated. The valence and conduction band offsets of the SD-LaAlO3/ALD-Al2O3 structure are measured by X-ray photoelectron spectroscopy to be 1.1 ± 0.2 and 1.6 ± 0.2 eV, respectively. The valence band discontinuity between H-diamond and LaAlO3 is evaluated to be 4.0 ± 0.2 eV, showing that the MOS structure acts as the gate which controls a hole carrier density. The leakage current density of the SD-LaAlO3/ALD-Al2O3/H-diamond MOS diode is smaller than 10-8 A cm-2 at gate bias from -4 to 2 V. The capacitance-voltage curve in the depletion mode shows sharp dependence, small flat band voltage, and small hysteresis shift, which implies low positive and trapped charge densities. The MOSFETs show p-type channel and complete normally off characteristics with threshold voltages changing from -3.6 ± 0.1 to -5.0 ± 0.1 V dependent on the gate length. The drain current maximum and the extrinsic transconductance of the MOSFET with gate length of 10 μm are -7.5 mA mm-1 and 2.3 ± 0.1 mS mm-1, respectively. The enhancement mode SD-LaAlO3/ALD-Al2O3/H-diamond MOSFET is concluded to be suitable for the applications of high power and high frequency electrical devices.

  7. Local self-field measurements in Tl-2223 polycrystalline superconductors

    Energy Technology Data Exchange (ETDEWEB)

    Saenz, A. [Univ. de Costa Rica, San Jose (Costa Rica). Escuela de Fisica; Niculescu, H. [Florida Agricultural and Mechanical Univ., Tallahassee, FL (United States). Dept. of Physics; Gielisse, P.J. [Dept. of Mechanical Engineering, Florida State Univ., Tallahassee, FL (United States)

    2000-07-01

    We report local self-field measurements on superconducting (Tl-2223) disks in an applied field. The axial components of the self-field generated by polycrystalline superconductors, have been measured at points above the sample using a Hall probe. The measurements were conducted with a computer controlled precision x-y scanning assembly, at liquid nitrogen temperatures. Single point and two- dimensional distributions of the local self-field above the samples immersed in a homogeneous applied field up to 16 mT, were recorded. In an increasing/decreasing magnetic field the magnetic response of the superconductors traverses hysteresis loops due to inter- and intragranular flux pinning. The field for full flux penetration and the maximum shielded field have been identified from characteristic points on the hysteresis loops. Evaluation of the average intergrain current density j{sub c}, assuming a uniform critical current density, resulted in the value 2.7 x 10{sup 6} A/m{sup 2}. (orig.)

  8. Identification of configuration and boundaries of interplanetary magnetic clouds

    Science.gov (United States)

    Feng, H. Q.; Wu, D. J.; Chao, J. K.

    2006-07-01

    To study interplanetary magnetic clouds (IMCs), it is important to find their configurations and boundaries from the observed magnetic field data. This paper presents a novel method of identifying the configuration and boundaries of IMCs, wherein the interplanetary magnetic field data, which are measured in the Geocentric Solar Ecliptic (GSE) coordinate system, are converted into an IMC natural coordinate system that can more clearly display the configuration and boundaries of the IMC as a flux tube. The establishment of the natural coordinate system is based on the idea that the IMC is a flux rope with approximately constant α force-free field configuration. We also apply this method to analyze four IMCs observed by the Wind spacecraft. Two of them are identified as having the flux rope configuration lying in the ecliptic plane, and the other two are flux ropes vertical to the ecliptic plane. The results demonstrate that our method can work well for real IMCs.

  9. The FORS1 catalogue of stellar magnetic field measurements

    CERN Document Server

    Bagnulo, S; Landstreet, J D; Izzo, C

    2015-01-01

    The FORS1 instrument on the ESO Very Large Telescope was used to obtain low-resolution circular polarised spectra of nearly a thousand different stars, with the aim of measuring their mean longitudinal magnetic fields. A catalogue of FORS1 magnetic measurements would provide a valuable resource with which to better understand the strengths and limitations of this instrument and of similar low-dispersion, Cassegrain spectropolarimeters. However, FORS1 data reduction has been carried out by a number of different groups using a variety of reduction and analysis techniques. Our understanding of the instrument and our data reduction techniques have both improved over time. A full re-analysis of FORS1 archive data using a consistent and fully documented algorithm would optimise the accuracy and usefulness of a catalogue of field measurements. Based on the ESO FORS pipeline, we have developed a semi-automatic procedure for magnetic field determinations, which includes self-consistent checks for field detection relia...

  10. Conceptual design of the 3D magnetic field configuration relevant to the magnetopause reconnection in the SPERF

    Science.gov (United States)

    Mao, Aohua; Ji, Hantao; Ren, Yang; E, Peng; Wang, Zhibin; Xiao, Qingmei; Xiao, Chijie

    2016-10-01

    A new terrella device, the Space Plasma Environment Research Facility (SPERF), is designed and under construction in China, with Asymmetric Reconnection EXperiment (AREX) as one component to study the interaction between the magnetosheath and magnetosphere plasmas. AREX will provide a unique platform for studying asymmetric magnetic reconnection relevant to the magnetopause, via a set of coils for simulating ``solar-wind-side'' magnetosheath field and a dipole field on the ``magnetosphere-side''. Thus it could be able to investigate a range of important issues in the magnetosphere geometry, such as the electron and ion-scale dynamics in the current sheet, particle and energy transfer from magnetosheath to magnetosphere, particle energization/heating during magnetic reconnection, 3D and asymmetric effects in fast reconnection, and so on. The plasma is generated by two flux cores at the ``magnetosheath-side'' and one electron cyclotron resonance source at the ``magnetosphere-side''. Different kinds of coils with specific current driven functions, as well as advanced diagnostics are designed. Motivation, overview of the AREX design and reconnection scenarios will be discussed.

  11. Free-field calibration of measurement microphones at high frequencies

    DEFF Research Database (Denmark)

    Barrera Figueroa, Salvador; Rasmussen, Knud; Torras Rosell, Antoni;

    2011-01-01

    Measurement microphones are typically calibrated in a free field at frequencies up to 50 kHz. This is a sufficiently high frequency for the most of sound measurement applications related with noise assessment. However, other applications such as assessment of the noise emitted by ultrasound clean...

  12. Research on intensity measurement in room impulse field

    Institute of Scientific and Technical Information of China (English)

    ZHAO Yueying; SHENG Shengwo; ZHAO Songling

    2008-01-01

    A new system of sound intensity measurement for impulse field in the room was proposed.This measurement system consists of a repeatable inspiriting sound source and a microphone fixed on a slowly rotating platform,which is equivalent to a circle microphone array composed of many perfectly matched microphones.The test principle was presented and typical application was described.Based upon this system the sound intensity measurement for impulse field in the room Was realized.Therefore,not only time but also spatial information of room impulse response can be obtained.

  13. Field quality measurements of a 2-Tesla transmission line magnet

    Energy Technology Data Exchange (ETDEWEB)

    Velev, G.V.; Foster, W.; Kashikhin, V.; Mazur, P.; Oleck, A.; Piekarz, H.; Schlabach, P.; Sylvester, C.; /Fermilab; Wake, M.; /KEK, Tsukuba

    2005-09-01

    A prototype 2-Tesla superconducting transmission line magnet for future hadron colliders was designed, built and tested at Fermilab. The 1.5 m long, combined-function gradient-dipole magnet has a vertical pole aperture of 20 mm. To measure the magnetic field quality in such a small magnet aperture, a specialized rotating coil of 15.2 mm diameter, 0.69 m long was fabricated. Using this probe, a program of magnetic field quality measurements was successfully performed. Results of the measurements are presented and discussed.

  14. Field Measurement for Superconducting Magnets of ADS Injector I

    CERN Document Server

    Yang, Xiangchen

    2013-01-01

    The superconducting solenoid magnet prototype for ADS injection-I had been fabricated in Beijing Qihuan Mechanical and Electric Engineer Company and tested in Haerbin Institute of Technology (HIT) in Nov, 2012. Batch magnet production was processed after some major revision from the magnet prototype, they include: removing off the perm-alloy shield, extending the iron yoke, using thin superconducting cable, etc. The first one of the batch magnets was tested in the vertical Dewar in HIT in Sept. 2013. Field measurement was carried out at the same time by the measurement platform that seated on the top of the vertical Dewar. This paper will present the field measurement system design, measurement results and discussion on the residual field from the persistent current effect.

  15. Auditory evoked field measurement using magneto-impedance sensors

    Energy Technology Data Exchange (ETDEWEB)

    Wang, K., E-mail: o-kabou@echo.nuee.nagoya-u.ac.jp; Tajima, S.; Song, D.; Uchiyama, T. [Graduate School of Engineering, Nagoya University, Nagoya (Japan); Hamada, N.; Cai, C. [Aichi Steel Corporation, Tokai (Japan)

    2015-05-07

    The magnetic field of the human brain is extremely weak, and it is mostly measured and monitored in the magnetoencephalography method using superconducting quantum interference devices. In this study, in order to measure the weak magnetic field of the brain, we constructed a Magneto-Impedance sensor (MI sensor) system that can cancel out the background noise without any magnetic shield. Based on our previous studies of brain wave measurements, we used two MI sensors in this system for monitoring both cerebral hemispheres. In this study, we recorded and compared the auditory evoked field signals of the subject, including the N100 (or N1) and the P300 (or P3) brain waves. The results suggest that the MI sensor can be applied to brain activity measurement.

  16. Adaptive framework for uncertainty analysis in electromagnetic field measurements.

    Science.gov (United States)

    Prieto, Javier; Alonso, Alonso A; de la Rosa, Ramón; Carrera, Albano

    2015-04-01

    Misinterpretation of uncertainty in the measurement of the electromagnetic field (EMF) strength may lead to an underestimation of exposure risk or an overestimation of required measurements. The Guide to the Expression of Uncertainty in Measurement (GUM) has internationally been adopted as a de facto standard for uncertainty assessment. However, analyses under such an approach commonly assume unrealistic static models or neglect relevant prior information, resulting in non-robust uncertainties. This study proposes a principled and systematic framework for uncertainty analysis that fuses information from current measurements and prior knowledge. Such a framework dynamically adapts to data by exploiting a likelihood function based on kernel mixtures and incorporates flexible choices of prior information by applying importance sampling. The validity of the proposed techniques is assessed from measurements performed with a broadband radiation meter and an isotropic field probe. The developed framework significantly outperforms GUM approach, achieving a reduction of 28% in measurement uncertainty.

  17. Measuring interstellar magnetic fields by radio synchrotron emission

    CERN Document Server

    Beck, Rainer

    2009-01-01

    Radio synchrotron emission, its polarization and its Faraday rotation are powerful tools to study the strength and structure of interstellar magnetic fields. The total intensity traces the strength and distribution of total magnetic fields. Total fields in gas-rich spiral arms and bars of nearby galaxies have strengths of 20-30 $\\mu$Gauss, due to the amplification of turbulent fields, and are dynamically important. In the Milky Way, the total field strength is about 6 $\\mu$G near the Sun and several 100 $\\mu$G in filaments near the Galactic Center. -- The polarized intensity measures ordered fields with a preferred orientation, which can be regular or anisotropic fields. Ordered fields with spiral structure exist in grand-design, barred, flocculent and even in irregular galaxies. The strongest ordered fields are found in interarm regions, sometimes forming "magnetic spiral arms" between the optical arms. Halo fields are X-shaped, probably due to outflows. -- The Faraday rotation of the polarization vectors tr...

  18. LIF Diagnostic for Measuring Beam-Transport Magnetic Fields

    Science.gov (United States)

    Jones, T. G.; Hinshelwood, D. D.; Neri, J. M.; Ottinger, P. F.; Noonan, W. A.

    1997-11-01

    A novel, spatially-resolved diagnostic is being developed to measure magnetic fields associated with intense ion beam propagation through a low-pressure gas, as is envisioned for light ion-driven ICF. The diagnostic technique uses laser-induced fluorescence (LIF) spectroscopy, and can be varied to measure either small or large fields. Small fields, as expected in ballistic transport with solenoidal lens focusing using ~ 1 Torr gas, produce Zeeman shifts, Δ λ_Z, smaller than the transition linewidth, Δ λ. High sensitivity to measure these shifts is achieved by a variation on the Babcock technique.^1 Large fields, as expected in self-pinched transport using 1--100 mTorr gas, produce Δ λZ larger than Δ λ. These Δ λZ will be resolved using an etalon as a narrowband, high-throughput optical filter. Available results from benchtop experiments using calibrated B-fields for both the small- and large-field techniques, and progress in fielding this diagnostic on the Gamble-II accelerator for beam-transport studies will be presented. Work supported by DOE through Sandia National Laboratories. ^ National Research Council Research Associate. ^ Present address University of Maryland, College Park, MD. ^1 W.A. Noonan, et al., Rev. Sci. Instrum. 68, 1032 (1997).

  19. Magnetic-Field-Response Measurement-Acquisition System

    Science.gov (United States)

    Woodward, Stanley E.; Shams, Qamar A.; Fox, Robert L.; Taylor, Bryant D.

    2006-01-01

    A measurement-acquisition system uses magnetic fields to power sensors and to acquire measurements from sensors. The system alleviates many shortcomings of traditional measurement-acquisition systems, which include a finite number of measurement channels, weight penalty associated with wires, use limited to a single type of measurement, wire degradation due to wear or chemical decay, and the logistics needed to add new sensors. Eliminating wiring for acquiring measurements can alleviate potential hazards associated with wires, such as damaged wires becoming ignition sources due to arcing. The sensors are designed as electrically passive inductive-capacitive or passive inductive-capacitive-resistive circuits that produce magnetic-field-responses. One or more electrical parameters (inductance, capacitance, and resistance) of each sensor can be variable and corresponds to a measured physical state of interest. The magnetic-field- response attributes (frequency, amplitude, and bandwidth) of the inductor correspond to the states of physical properties for which each sensor measures. For each sensor, the measurement-acquisition system produces a series of increasing magnetic-field harmonics within a frequency range dedicated to that sensor. For each harmonic, an antenna electrically coupled to an oscillating current (the frequency of which is that of the harmonic) produces an oscillating magnetic field. Faraday induction via the harmonic magnetic fields produces an electromotive force and therefore a current in the sensor. Once electrically active, the sensor produces its own harmonic magnetic field as the inductor stores and releases magnetic energy. The antenna of the measurement- acquisition system is switched from a transmitting to a receiving mode to acquire the magnetic-field response of the sensor. The rectified amplitude of the received response is compared to previous responses to prior transmitted harmonics, to ascertain if the measurement system has detected a

  20. Firewall Configuration Errors Revisited

    CERN Document Server

    Wool, Avishai

    2009-01-01

    The first quantitative evaluation of the quality of corporate firewall configurations appeared in 2004, based on Check Point FireWall-1 rule-sets. In general that survey indicated that corporate firewalls were often enforcing poorly written rule-sets, containing many mistakes. The goal of this work is to revisit the first survey. The current study is much larger. Moreover, for the first time, the study includes configurations from two major vendors. The study also introduce a novel "Firewall Complexity" (FC) measure, that applies to both types of firewalls. The findings of the current study indeed validate the 2004 study's main observations: firewalls are (still) poorly configured, and a rule-set's complexity is (still) positively correlated with the number of detected risk items. Thus we can conclude that, for well-configured firewalls, ``small is (still) beautiful''. However, unlike the 2004 study, we see no significant indication that later software versions have fewer errors (for both vendors).

  1. Computation of temperature elevation in rabbit eye irradiated by 2.45-GHz microwaves with different field configurations.

    Science.gov (United States)

    Hirata, Akimasa; Watanabe, Soichi; Taki, Masao; Fujiwara, Osamu; Kojima, Masami; Sasaki, Kazuyuki

    2008-02-01

    This study calculated the temperature elevation in the rabbit eye caused by 2.45-GHz near-field exposure systems. First, we calculated specific absorption rate distributions in the eye for different antennas and then compared them with those observed in previous studies. Next, we re-examined the temperature elevation in the rabbit eye due to a horizontally-polarized dipole antenna with a C-shaped director, which was used in a previous study. For our computational results, we found that decisive factors of the SAR distribution in the rabbit eye were the polarization of the electromagnetic wave and antenna aperture. Next, we quantified the eye average specific absorption rate as 67 W kg(-1) for the dipole antenna with an input power density at the eye surface of 150 mW cm(-2), which was specified in the previous work as the minimum cataractogenic power density. The effect of administrating anesthesia on the temperature elevation was 30% or so in the above case. Additionally, the position where maximum temperature in the lens appears is discussed due to different 2.45-GHz microwave systems. That position was found to appear around the posterior of the lens regardless of the exposure condition, which indicates that the original temperature distribution in the eye was the dominant factor.

  2. Reconstructing material properties by deconvolution of full-field measurement images: The conductivity case

    Science.gov (United States)

    Bellis, Cédric; Trabelsi, Manel; Frémy, Flavien

    2017-03-01

    This study concerns the reconstruction of material parameters from full-field measurements. In this context the typical available data is a set of digital images that is seldom handled as such when solving the inverse problem. Therefore, this work investigates a direct method to compute constitutive parameter maps from full-field measurement images. Within the prototypical framework of the periodic conductivity model, the starting point for the proposed approach is the Lippmann-Schwinger equation, which is satisfied by the fields measured internally. This integral equation is reinterpreted as a linear convolution model for the sought conductivity field. Considering that multiple experiments might be available and then combined, this problem is solved in the least-square sense. To do so, the Krylov subspace-based LSQR algorithm is employed. Full advantage is taken of the convenient expression of the featured Green’s function in Fourier space and of the intensive use of the fast Fourier transform (FFT). Moreover, a spectral-based filtering regularization scheme is implemented to tackle noisy data. Overall, the proposed reconstruction algorithm only handles image-like quantities in an efficient mesh-free approach. The performance of the method is assessed on a set of synthetic 2D numerical examples both for isotropic and anisotropic material configurations.

  3. Verification of Electromagnetic Field Measurements via Inter-laboratory Comparison Measurements

    OpenAIRE

    Mann, M.; H. Brüggemeyer; Weiß, P.

    2005-01-01

    An inter-laboratory comparison of field strength measurements was conducted in order to verify the comparability of high-frequency electromagnetic field measurements. For this purpose, 17 participating teams hosted by the working group "procedures of exposure determination" of the LAI (Länderausschuss für Immissionsschutz, state committee on immission control) determined the field strength at given stations around a hospital situation. At those stations very diffe...

  4. Spherical near-field antenna measurements — The most accurate antenna measurement technique

    DEFF Research Database (Denmark)

    Breinbjerg, Olav

    2016-01-01

    The spherical near-field antenna measurement technique combines several advantages and generally constitutes the most accurate technique for experimental characterization of radiation from antennas. This paper/presentation discusses these advantages, briefly reviews the early history and present...... status, and addresses future challenges for spherical near-field antenna measurements; in particular, from the viewpoint of the DTU-ESA Spherical Near-Field Antenna Test Facility....

  5. PIV MEASUREMENTS FOR GAS FLOW UNDER GRADIENT MAGNETIC FIELDS

    Institute of Scientific and Technical Information of China (English)

    RUAN Xiaodong; WU Feng; F.YAMAMOTO

    2004-01-01

    Particle Image Velocimetry (PIV) techniques were developed to measure the convective N2-air flow under gradient magnetic fields. The velocity fields were calculated by the Minimum Quadratic Difference (MQD) algorithm and spurious vectors were eliminated by Delaunay Tessellation.The N2-air flow was measured as the magnetic flux density varying from 0 ~ 1.5 T. A strengthened vortex flow of air was observed under the condition that the magnetic field was applied, and the velocity of N2 jet rose with the increase of the magnetic density. The experimental results show that the magnetic force will induce a vortex flow and cause a convection flow of the air mixture when both gradients of the O2 concentration and the magnetic field intensity exist.

  6. Measurement of field-free molecular alignment by balanced weak field polarization technique

    Directory of Open Access Journals (Sweden)

    Peng Peng

    2015-12-01

    Full Text Available We demonstrate the measurement of field-free molecular alignment of air can be realized by combining the weak field polarization technique (WFPT with a balanced detection system. The measured signal is proportional to the alignment parameter. Periodic revival structures of the transient alignment and permanent alignment between revivals can be detected clearly by a single measurement with high sensitivity. Fourier transform spectrum of the measured signal agrees well with the calculation result and provides information of the populations of different J states in the rotational wave packet.

  7. Magnetic field, closed orbit, and energy measurement in the Bevatron

    Energy Technology Data Exchange (ETDEWEB)

    Crebbin, K.C.

    1981-11-01

    This report provides the information necessary for a better evaluation of particle energy in the Bevatron. Previously, the nominal magnetic field value and radius were used to calculate the value for the kinetic energy of the particle. This value was good to a few percent. Today, more and more experimenters would like to know the energy to a more precise value. To this end, corrections to the measured magnetic field values and the radial closed orbit are provided.

  8. Fifth generation lithospheric magnetic field model from CHAMP satellite measurements

    OpenAIRE

    Maus, S.; Hermann Lühr; Martin Rother; Hemant, K.; Balasis, G.; Patricia Ritter; Claudia Stolle

    2007-01-01

    Six years of low-orbit CHAMP satellite magnetic measurements have provided an exceptionally high-quality data resource for lithospheric magnetic field modeling and interpretation. Here we describe the fifth-generation satellite-only magnetic field model MF5. The model extends to spherical harmonic degree 100. As a result of careful data selection, extensive corrections, filtering, and line leveling, the model has low noise levels, even if evaluated at the Earth's surface. The model is particu...

  9. submitter Generalized Harmonic Analysis of Computed and Measured Magnetic Fields

    CERN Document Server

    Auchmann, B; Petrone, C; Russenschuck, S

    2016-01-01

    In this paper, we present a generalized approach for the harmonic analysis of the magnetic field in accelerator magnets. This analysis is based on the covariant components of the computed or measured magnetic flux density. The multipole coefficients obtained in this way can be used for magnet optimization and field reconstruction in the interior of circular and elliptical boundaries in the bore of straight magnets.

  10. Field Measurements of Black Carbon Yields from Gas Flaring.

    Science.gov (United States)

    Conrad, Bradley M; Johnson, Matthew R

    2017-02-07

    Black carbon (BC) emissions from gas flaring in the oil and gas industry are postulated to have critical impacts on climate and public health, but actual emission rates remain poorly characterized. This paper presents in situ field measurements of BC emission rates and flare gas volume-specific BC yields for a diverse range of flares. Measurements were performed during a series of field campaigns in Mexico and Ecuador using the sky-LOSA optical measurement technique, in concert with comprehensive Monte Carlo-based uncertainty analyses. Parallel on-site measurements of flare gas flow rate and composition were successfully performed at a subset of locations enabling direct measurements of fuel-specific BC yields from flares under field conditions. Quantified BC emission rates from individual flares spanned more than 4 orders of magnitude (up to 53.7 g/s). In addition, emissions during one notable ∼24-h flaring event (during which the plume transmissivity dropped to zero) would have been even larger than this maximum rate, which was measured as this event was ending. This highlights the likely importance of superemitters to global emission inventories. Flare gas volume-specific BC yields were shown to be strongly correlated with flare gas heating value. A newly derived correlation fitting current field data and previous lab data suggests that, in the context of recent studies investigating transport of flare-generated BC in the Arctic and globally, impacts of flaring in the energy industry may in fact be underestimated.

  11. Using optical soliton stability for magnetic field measurement

    Science.gov (United States)

    Şchiopu, IonuÅ£ Romeo; ǎgulinescu, Andrei, Dr; Marinescu, Andrei

    2015-02-01

    In this paper we propose a novel optical method for measuring the circular magnetic field. In practice, many situations may appear in which there are difficulties in measuring the magnetic field, as inside coils, motors etc., where the magnetic field lines are circular or elliptical. The proposed method, applied for measuring the current on high voltage lines, strongly benefits from the advantages that it offers as compared to classical solutions based on the inductive principle. Some of the advantages of optoelectronic and optic measurement methods have a real importance. These advantages consist in: avoiding the use of energy intensive materials (Cu, Fe etc.), reducing the weight of the measuring system, reducing at the minimum the fire danger due to the use of paper-oil insulation in high voltage devices etc. The novelty of our proposed method consists in using the electromagnetic radiation in ultrashort pulses, having a relatively large frequency band and a much improved resistance to external perturbations, for measuring the circular magnetic field generated from the current of high voltage lines, inside power transformers or high power motors.

  12. Magnetopause Reconnection Impact Parameters from Multiple Spacecraft Magnetic Field Measurements

    Science.gov (United States)

    Wendel, Deirdre E.; Reiff, Patricia H.

    2009-01-01

    We present a novel technique that exploits multiple spacecraft data to determine the impact parameters of the most general form of magnetic reconnection at the magnetopause. The method consists of a superposed epoch of multiple spacecraft magnetometer measurements that yields the instantaneous magnetic spatial gradients near a magnetopause reconnection site. The gradients establish the instantaneous positions of the spacecraft relative to the reconnection site. The analysis is well suited to evaluating the spatial scales of singular field line reconnection, which is characterized by a two-dimensional x-type topology adjacent and perpendicular to a reconnecting singular field line. Application of the method to Cluster data known to lie in the vicinity of a northward IMF reconnection site establishes a field topology consistent with singular field line reconnection and a normal magnetic field component of 20 nT. The corresponding current structure consists of a 130 km sheet possibly embedding a thinner. bifurcated sheet.

  13. Full-field measurements and identification in solid mechanics

    CERN Document Server

    Grediac, Michel

    2008-01-01

    This timely book presents cutting-edge developments by experts in the field on the rapidly developing and scientifically challenging area of full-field measurement techniques used in solid mechanics - including photoelasticity, grid methods, deflectometry, holography, speckle interferometry and digital image correlation. The evaluation of strains and the use of the measurements in subsequent parameter identification techniques to determine material properties are also presented. Since parametric identification techniques require a close coupling of theoretical models and experimental measurements, the book focuses on specific modeling approaches that include finite element model updating, the equilibrium gap method, constitutive equation gap method, virtual field method and reciprocity gap method. In the latter part of the book, the authors discuss two particular applications of selected methods that are of special interest to many investigators: the analysis of localized phenomenon and connections between mi...

  14. Remote optical sensor system for E-field measurements

    Science.gov (United States)

    Heinzelmann, Robert; Stoehr, Andreas; Alder, Thomas; Kalinowski, D.; Schmidt, Manuel; Gross, Matthias; Jaeger, Dieter

    1998-12-01

    The concept of a remote optical sensor system for frequency selective electric field measurements will be presented. The system will be applicable to field measurement problems up to frequencies in the microwave regime. Additionally, it will provide minimum interference with the measured field, due to the optical fiber coupled sensor head. The electrooptic key components within the head of this sensor system are an array of photovoltaic cells and an electroabsorption waveguide modulator. Based on experimental results these components will be discussed and evaluated for the application within the sensor system. Furthermore, a novel fiber modulator coupling technique employing the monolithic integration of the device with InP V-grooves will be presented.

  15. Pulsed neutron fields measurements around a synchrotron storage ring

    Science.gov (United States)

    Caresana, Marco; Ballerini, Marcello; Ulfbeck, David Garf; Hertel, Niels; Manessi, Giacomo Paolo; Søgaard, Carsten

    2017-09-01

    A measurement campaign was performed for characterizing the neutron ambient dose equivalent, H*(10), in selected positions at ISA, Aarhus, Denmark, around the ASTRID and ASTRID2 storage rings. The neutron stray radiation field is characterized here by very intense radiation bursts with a low repetition rate, which result in a comparatively low average H*(10) rate. As a consequence, devices specifically conceived for operating in pulsed neutron fields must be employed for efficiently measuring in this radiation environment, in order to avoid severe underestimations of the H*(10) rate. The measurements were performed with the ELSE NUCLEAR LUPIN 5401 BF3-NP rem counter, a detector characterized by an innovative working principle that is not affected by dead time losses. This allowed characterizing both the H*(10) and the time structure of the radiation field in the pre-selected positions.

  16. Pulsed beams as field probes for precision measurement

    OpenAIRE

    Hudson, J. J.; Ashworth, H. T.; Kara, D. M.; Tarbutt, M. R.; Sauer, B.E.; Hinds, E. A.

    2007-01-01

    We describe a technique for mapping the spatial variation of static electric, static magnetic, and rf magnetic fields using a pulsed atomic or molecular beam. The method is demonstrated using a beam designed to measure the electric dipole moment of the electron. We present maps of the interaction region, showing sensitivity to (i) electric field variation of 1.5 V/cm at 3.3 kV/cm with a spatial resolution of 15 mm; (ii) magnetic field variation of 5 nT with 25 mm resolution; (iii) radio-frequ...

  17. Estimating of pulsed electric fields using optical measurements.

    Energy Technology Data Exchange (ETDEWEB)

    Flanagan, Timothy McGuire; Chantler, Gary.

    2013-09-01

    We performed optical electric field measurements ion nanosecond time scales using the electrooptic crystal beta barium borate (BBO). Tests were based on a preliminary bench top design intended to be a proofofprinciple stepping stone towards a modulardesign optical Efield diagnostic that has no metal in the interrogated environment. The long term goal is to field a modular version of the diagnostic in experiments on large scale xray source facilities, or similarly harsh environments.

  18. Evolution of the Coronal Magnetic Configurations Including a Current-Carrying Flux Rope in Response to the Change in the Background Field

    CERN Document Server

    Wang, Hong-Juan; Gong, Jian-Cun; Lin, Jun

    2014-01-01

    We investigate equilibrium height of the flux rope, and its internal equilibrium in a realistic plasma environment by carrying out numerical simulations of the evolution of systems including a current-carrying flux rope. We find that the equilibrium height of the flux rope is approximately a power-law function of the relative strength of the background field. Our simulations indicate that the flux rope can escape more easily from a weaker background field. This further confirms the catastrophe in the magnetic configuration of interest can be triggered by decrease of strength of the background field. Our results show that it takes some time to reach internal equilibrium depending on the initial state of the flux rope. The plasma flow inside the flux rope due to the adjustment for the internal equilibrium of the flux rope remains small and does not last very long when the initial state of the flux rope commences from the stable branch of the theoretical equilibrium curve. This work also confirms the influence o...

  19. Indirect measurement of the magnetocaloric effect using a novel differential scanning calorimeter with magnetic field.

    Science.gov (United States)

    Jeppesen, S; Linderoth, S; Pryds, N; Kuhn, L Theil; Jensen, J Buch

    2008-08-01

    A simple and high-sensitivity differential scanning calorimeter (DSC) unit operating under magnetic field has been built for indirect determination of the magnetocaloric effect. The principle of the measuring unit in the calorimeter is based on Peltier elements as heat flow sensors. The high sensitivity of the apparatus combined with a suitable calibration procedure allows very fast and accurate heat capacity measurements under magnetic field to be made. The device was validated from heat capacity measurements for the typical DSC reference material gallium (Ga) and a La(0.67)Ca(0.33)MnO(3) manganite system and the results were highly consistent with previous reported data for these materials. The DSC has a working range from 200 to 340 K and has been tested in magnetic fields reaching 1.8 T. The signal-to-noise ratio is in the range of 10(2)-10(3) for the described experiments. Finally the results have been compared to results from a Quantum Design(R) physical properties measuring system. The configuration of the system also has the advantage of being able to operate with other types of magnets, e.g., permanent magnets or superconducting coils, as well as the ability to be expanded to a wider temperature range.

  20. A vector-free ECG interpretation with P, QRS & T waves as unbalanced transitions between stable configurations of the heart electric field during P-R, S-T & T-P segments

    Science.gov (United States)

    2014-01-01

    Since cell membranes are weak sources of electrostatic fields, this ECG interpretation relies on the analogy between cells and electrets. It is here assumed that cell-bound electric fields unite, reach the body surface and the surrounding space and form the thoracic electric field that consists from two concentric structures: the thoracic wall and the heart. If ECG leads measure differences in electric potentials between skin electrodes, they give scalar values that define position of the electric field center along each lead. Repolarised heart muscle acts as a stable positive electric source, while depolarized heart muscle produces much weaker negative electric field. During T-P, P-R and S-T segments electric field is stable, only subtle changes are detectable by skin electrodes. Diastolic electric field forms after ventricular depolarization (T-P segments in the ECG recording). Telediastolic electric field forms after the atria have been depolarized (P-Q segments in the ECG recording). Systolic electric field forms after the ventricular depolarization (S-T segments in the ECG recording). The three ECG waves (P, QRS and T) can then be described as unbalanced transitions of the heart electric field from one stable configuration to the next and in that process the electric field center is temporarily displaced. In the initial phase of QRS, the rapidly diminishing septal electric field makes measured potentials dependent only on positive charges of the corresponding parts of the left and the right heart that lie within the lead axes. If more positive charges are near the "DOWN" electrode than near the "UP" electrode, a Q wave will be seen, otherwise an R wave is expected. Repolarization of the ventricular muscle is dampened by the early septal muscle repolarization that reduces deflection of T waves. Since the "UP" electrode of most leads is near the usually larger left ventricle muscle, T waves are in these leads positive, although of smaller amplitude and longer

  1. Out-of-field dose measurements in radiotherapy

    Energy Technology Data Exchange (ETDEWEB)

    Kaderka, Robert

    2011-07-13

    This thesis describes the results from measurements of the out-of-field dose in radiotherapy. The dose outside the treatment volume has been determined in a water phantom and an anthropomorphic phantom. Measurements were performed with linac photons, passively delivered protons, scanned protons, passively delivered carbon ions as well as scanned carbon ions. It was found that the use of charged particles for radiotherapy reduces the out-of-field dose by up to three orders of magnitude compared to conventional radiotherapy with photons.

  2. Direct field measurement of the dynamic amplification in a bridge

    Science.gov (United States)

    Carey, Ciarán; OBrien, Eugene J.; Malekjafarian, Abdollah; Lydon, Myra; Taylor, Su

    2017-02-01

    In this paper, the level of dynamics, as described by the Assessment Dynamic Ratio (ADR), is measured directly through a field test on a bridge in the United Kingdom. The bridge was instrumented using fiber optic strain sensors and piezo-polymer weigh-in-motion sensors were installed in the pavement on the approach road. Field measurements of static and static-plus-dynamic strains were taken over 45 days. The results show that, while dynamic amplification is large for many loading events, these tend not to be the critical events. ADR, the allowance that should be made for dynamics in an assessment of safety, is small.

  3. Comparison of Simulated and Measured Non-linear Ultrasound Fields

    DEFF Research Database (Denmark)

    Du, Yigang; Jensen, Henrik; Jensen, Jørgen Arendt

    2011-01-01

    In this paper results from a non-linear AS (angular spectrum) based ultrasound simulation program are compared to water-tank measurements. A circular concave transducer with a diameter of 1 inch (25.4 mm) is used as the emitting source. The measured pulses are rst compared with the linear...... simulation program Field II, which will be used to generate the source for the AS simulation. The generated non-linear ultrasound eld is measured by a hydrophone in the focal plane. The second harmonic component from the measurement is compared with the AS simulation, which is used to calculate both...

  4. A Diagnostic for Electric Field Measurements in the Near/Far-Field Regions of ICRF Antenna

    Science.gov (United States)

    Martin, E. H.; Caughman, J. B. O.; Isler, R. C.

    2015-11-01

    The physics mechanisms of wave heating and current drive processes in the bulk hot plasma are generally well identified. However, details of the wave-plasma interaction with a material surface in the cold plasma edge are still not fully understood. The driver behind this interaction is the time-periodic wave electric field and is referred to as the near/far-field depending on the location with respect to the antenna. Various models have been formulated to capture the near/far-field physics but have not been tested experimentally. Thus, a diagnostic capable of measuring the electric field with temporal and 3D-spatial resolution is critical for confidence in the codes used to design next generation ICRF antennas. This research is focused on the development of a laser based spectroscopic technique, Doppler-free saturation spectroscopy (DFSS), and its implementation to study near/far-field physics. Using DFSS the spectra line profile of various electronic transitions are measured and fit to a quantum mechanical model incorporating both magnetic and dynamic electric field operators. The electric field direction and magnitude are extracted from the fit. The experimental setup and planned experiments will be discussed. Additionally, initial measurements of fitted Hδ spectrum under the influence of known electric and magnetic fields will be presented.

  5. Analyzing Extragalactic Magnetic Fields Using Faraday Rotation Measure Synthesis

    Science.gov (United States)

    Pare, Dylan; Wang, Q. Daniel; Kamieneski, Patrick; Sullivan, Kendall

    2017-01-01

    Extragalactic magnetic fields are a poorly understood element of galaxies that are likely to play an important role in galaxy formation and evolution. Until recently, however, there was no way to observe these fields to a high level of detail, making it difficult to map the spatial distribution of these fields to any high degree of accuracy. Fortunately, a new technique known as Faraday Rotation Measure Synthesis allows for a more precise analysis of galactic magnetism. This technique uses the observed Faraday rotation of polarized emission from background sources to map the magnetic field of a foreground galaxy. This Faraday rotation occurs when the polarized emission encounters ionized, magnetized gas within the galaxy, causing the emission to be rotated by an amount proportional the magnetic field subjected to the ionized gas. Working as part of CHANG-ES (Continuum HAlos in Nearby Galaxies - an EVLA Survey), we have applied this technique in order to learn about the distribution of magnetic fields in the disks and halos of edge-on spiral galaxies. We will present maps of the galactic magnetic fields of CHANG-ES galaxies using this technique, indicating the potential of this technique in successfully mapping these distant fields.

  6. Micro analysis of fringe field formed inside LDA measuring volume

    Science.gov (United States)

    Ghosh, Abhijit; Nirala, A. K.

    2016-05-01

    In the present study we propose a technique for micro analysis of fringe field formed inside laser Doppler anemometry (LDA) measuring volume. Detailed knowledge of the fringe field obtained by this technique allows beam quality, alignment and fringe uniformity to be evaluated with greater precision and may be helpful for selection of an appropriate optical element for LDA system operation. A complete characterization of fringes formed at the measurement volume using conventional, as well as holographic optical elements, is presented. Results indicate the qualitative, as well as quantitative, improvement of fringes formed at the measurement volume by holographic optical elements. Hence, use of holographic optical elements in LDA systems may be advantageous for improving accuracy in the measurement.

  7. Full-field laser vibration measurement in NDT techniques

    Science.gov (United States)

    Yue, Kaiduan; Li, Zhongke; Yi, Yaxing; Zhang, Fei

    2008-12-01

    Research of Non Destructive Testing (NDT) methodology has developed rapidly in recent years[1][2]. But it is rarely used for small objects such as Micro-electronic Mechanics System. Due to the small size of the MEMS, the traditional method of contact measurement seriously affects the parameter of the object measured. So a high accuracy non-contact measurement is required for optimization of MEMS designs and improvement of its reliability[3][4]. With recent advances in photonics, electronics, and computer technology, a Non Destructive Testing (NDT) laser time average interferometry is proposed in the paper. Laser interferometry has the advantages of non-contact, high accuracy, full-field and fast speed, so it can be used to detect cracks in MEMS. A time average measurement method of digital speckle pattern interferometry is proposed to measure the vibration mode of the MEMS in the paper. According to the sudden change of amplitude of vibration mode, a crack can be measured. With the speckle average technology, high accuracy phase-shift, continuous phase scanning technology, combined with optical amplification technology, the resolution of the amplitude reaches 1nm, and the resolution of the crack reaches 5μm. The measurement system being full-field, the measuring speed of the measurement system can reach 512*512 points per one minute.

  8. Planetary science. Low-altitude magnetic field measurements by MESSENGER reveal Mercury's ancient crustal field.

    Science.gov (United States)

    Johnson, Catherine L; Phillips, Roger J; Purucker, Michael E; Anderson, Brian J; Byrne, Paul K; Denevi, Brett W; Feinberg, Joshua M; Hauck, Steven A; Head, James W; Korth, Haje; James, Peter B; Mazarico, Erwan; Neumann, Gregory A; Philpott, Lydia C; Siegler, Matthew A; Tsyganenko, Nikolai A; Solomon, Sean C

    2015-05-22

    Magnetized rocks can record the history of the magnetic field of a planet, a key constraint for understanding its evolution. From orbital vector magnetic field measurements of Mercury taken by the MErcury Surface, Space ENvironment, GEochemistry, and Ranging (MESSENGER) spacecraft at altitudes below 150 kilometers, we have detected remanent magnetization in Mercury's crust. We infer a lower bound on the average age of magnetization of 3.7 to 3.9 billion years. Our findings indicate that a global magnetic field driven by dynamo processes in the fluid outer core operated early in Mercury's history. Ancient field strengths that range from those similar to Mercury's present dipole field to Earth-like values are consistent with the magnetic field observations and with the low iron content of Mercury's crust inferred from MESSENGER elemental composition data. Copyright © 2015, American Association for the Advancement of Science.

  9. Work function measurements by the field emission retarding potential method.

    Science.gov (United States)

    Strayer, R. W.; Mackie, W.; Swanson, L. W.

    1973-01-01

    Description of the theoretical foundation of the field electron retarding potential method, and review of its experimental application to the measurement of single crystal face work functions. The results obtained from several substrates are discussed. An interesting and useful fallout from the experimental approach described is the ability to accurately measure the elastic and inelastic reflection coefficient for impinging electrons to near zero-volt energy.

  10. Measurement of hadronic shower punchthrough in magnetic field

    CERN Document Server

    Albajar, C; Arefev, A; Bacci, Cesare; Bencze, G L; Bergman, R; Bizzeti, A; Brouwer, C; Cardarelli, R; Casoli, P; Centro, Sandro; Ceradini, F; Choumilov, E; Chrisman, D; Ciapetti, G; Civinini, C; Cline, D; D'Alessandro, R; Della Negra, Michel; Dénes, E; Di Ciaccio, Anna; Dominik, Wojciech; Faissner, Helmut; Ferrando, A; Fouz-Iglesias, M C; Gorn, W; Górski, M; Hervé, A; Iglesias, A; Juntunen, M; Karimäki, V; Kinnunen, Ritva; Kluge, A; Kolotaev, Yu; Konecki, M; König, A C; Kólikowski, J; Lacava, F; Layter, J G; Le Coultre, P; Lyndon, C; Malinin, A; Margutti, G; Martinelli, R; Martínez-Laso, L; McNeil, R R; Meneguzzo, Anna Teresa; Meschini, M; Moers, T; Mohammadi-Baarmand, M; Nisati, A; Orestano, D; Österberg, K; Otwinowski, S; Petrolo, E; Pimiä, M; Pozhidaev, V; Pols, C L A; Pontecorvo, L; Porth, Paul; Radermacher, E; Razen, B; Reithler, H; Ribeiro, R; Rojkov, A; Sanjari, A H; Santonico, R; Sartori, P; Shank, J T; Schwarthoff, H; Seez, Christopher J; Shen, B C; Szeptycka, M; Szoncsó, F; Teykal, H F; Tolsma, H; Tuchscherer, H; Tuominiemi, Jorma; Tuuva, T; van der Graaf, H; Veneziano, Stefano; Verzocchi, M; Vesztergombi, G; Wagner, H; Walzel, G; Wijnen, T A M; Wilson, G W; Wrochna, G; Wulz, Claudia Elisabeth; Zanello, L; Zotto, P L

    1996-01-01

    The total punchthrough probability of showers produced by negative pions, positive pions, positive kaons and protons, has been measured as a function of depth in an absorber in a magnetic field ranging from 0 to 3 Tesla. The incident particle momentum varied from 10 to 300 GeV/c. The lateral shower development and particle multiplicity at several absorber depths have been determined. The measurements are compared with the predictions of Monte Carlo simulation programs.

  11. Toward a rapid 3D spectral deconvolution of EMI conductivities measured with portable multi-configuration sensors

    Science.gov (United States)

    Guillemoteau, Julien; Tronicke, Jens

    2017-04-01

    Portable loop-loop electromagnetic induction (EMI) sensors using multiple coil configurations are of growing interest in hydrological, archaeological and agricultural studies for mapping the subsurface electrical conductivity. In contrast with EMI methods employing larger scale geometries (e.g., magnetotellurics, marine EM, airborne EM, transient EM, large offset loop-loop harmonic source EM), the portable EMI multi-configuration sensors operate in the low induction number (LIN) domain as they employ a rather low frequency harmonic source (< 20 kHz) and rather small coil separations (≤ 2 m). In the LIN domain, electrical conductivity has a minor effect on the forward modelling kernel. Accordingly, we have developed an algorithm to model this kind of data, which is based on a homogeneous half-space kernel. By formulating the problem in the hybrid spectral-spatial domain (kx, ky, z), we show that it is possible to generate large data maps containing more than 100,000 stations within a minute on a standard modern laptop computer. We compared this forward modelling approach to a robust approach based on the integral equation (IE) method. Our results show that, as long as the LIN approximation is fulfilled (i.e., for the system of interest, if the electrical conductivity is smaller than 0.5 S/m), the linear theory allows to accurately and robustly handle the structural characteristics of the subsurface conductivity distribution. We therefore expect that our forward modelling procedure can be implemented in rapid multi-channel deconvolution procedures in order to rapidly extract the structural properties of the subsurface conductivity distribution from data sets acquired across rather large (hectare scale) areas.

  12. Control Configuration Selection for Multivariable Descriptor Systems

    DEFF Research Database (Denmark)

    Shaker, Hamid Reza; Stoustrup, Jakob

    2012-01-01

    is needed to be controlled, is either in the descriptor form or can be represented in the descriptor form. Singular systems and the differential algebraic equation (DAE) systems are among these systems. Descriptor systems appear in the variety of fields to describe the practical processes ranging from power...... systems, hydraulic systems to heat transfer, and chemical processes. The focus of this paper is on the problem of control configuration selection for multivariable descriptor systems. A gramian-based interaction measure for control configuration selection of such processes is described in this paper...

  13. MEASUREMENTS OF STELLAR MAGNETIC FIELDS USING AUTOCORRELATION OF SPECTRA

    Energy Technology Data Exchange (ETDEWEB)

    Borra, E. F.; Deschatelets, D. [Département de physique, de génie physique et d’optique. Université Laval (Canada)

    2015-11-15

    We present a novel technique that uses the autocorrelation of the spectrum of a star to measure the line broadening caused by the modulus of its average surface magnetic field. The advantage of the autocorrelation comes from the fact that it can detect very small spectral line broadening effects because it averages over many spectral lines and therefore gives an average with a very high signal-to-noise ratio. We validate the technique with the spectra of known magnetic stars and obtain autocorrelation curves that are in full agreement with published magnetic curves obtained with Zeeman splitting. The autocorrelation also gives less noisy curves so that it can be used to obtain very accurate curves. We degrade the resolution of the spectra of these magnetic stars to lower spectral resolutions where the Zeeman splitting is undetectable. At these resolutions, the autocorrelation still gives good quality curves, thereby showing that it can be used to measure magnetic fields in spectra where the Zeeman splitting is significantly smaller than the width of the spectral line. This would therefore allow observing magnetic fields in very faint Ap stars with low-resolution spectrographs, thereby greatly increasing the number of known magnetic stars. It also demonstrates that the autocorrelation can measure magnetic fields in rapidly rotating stars as well as weak magnetic fields that give a Zeeman splitting smaller than the intrinsic width of the spectral lines. Finally, it shows that the autocorrelation can be used to find unknown magnetic stars in low-resolution spectroscopic surveys.

  14. MESSENGER Measurements of Mercury's Magnetic Field during the First Flyby

    Science.gov (United States)

    Slavin, James A.; Boardsen, S. A.; Acuna, M. H.; Anderson, B. J.; Johnson, C. L.; Korth, H.; Krimigis, S. M.; McNutt, R. L., Jr.; Purucker, M. E.; Solomon, S. C.

    2008-01-01

    On 14 January 2008 the MESSENGER spacecraft will encounter Mercury for the first time. Depending upon the solar wind conditions, this initial flyby will return Magnetometer measurements of Mercury's magnetic field over a time interval lasting between - 30 md 60 min. Closest approach for MESSENGER is targeted for an altitude of 200 km as compared with the 707 krn and 327 km attained by Mariner 10 on 29 March 1974 and 16 March 1975, respectively. Furthermore, the differences in the MESSENGER and Mariner 10 encounter trajectories, with respect both to magnetospheric and body-fixed coordinates are highly complementary and expected to lead to significant improvements in our knowledge of Mercury's magnetic field. We present an overview of the MESSENGER magnetic field observations, an initial subtraction of the magnetic fields attributable to magnetospheric current systems from the total measured magnetic field, and an improved model of Mercury's intrinsic magnetic field. We also discuss the expected advances afforded by the two additional MESSENGER flybys, which occur in October 2008 and September 2009, as well as the orbital phase that will begin in March 201 1.

  15. A System for Acoustic Field Measurement Employing Cartesian Robot

    Directory of Open Access Journals (Sweden)

    Szczodrak Maciej

    2016-09-01

    Full Text Available A system setup for measurements of acoustic field, together with the results of 3D visualisations of acoustic energy flow are presented in the paper. Spatial sampling of the field is performed by a Cartesian robot. Automatization of the measurement process is achieved with the use of a specialized control system. The method is based on measuring the sound pressure (scalar and particle velocity(vector quantities. The aim of the system is to collect data with a high precision and repeatability. The system is employed for measurements of acoustic energy flow in the proximity of an artificial head in an anechoic chamber. In the measurement setup an algorithm for generation of the probe movement path is included. The algorithm finds the optimum path of the robot movement, taking into account a given 3D object shape present in the measurement space. The results are presented for two cases, first without any obstacle and the other - with an artificial head in the sound field.

  16. Determination of the absolute configuration of perylene quinone-derived mycotoxins by measurement and calculation of electronic circular dichroism spectra and specific rotations.

    Science.gov (United States)

    Podlech, Joachim; Fleck, Stefanie C; Metzler, Manfred; Bürck, Jochen; Ulrich, Anne S

    2014-09-01

    Altertoxins I-III, alterlosins I and II, alteichin (alterperylenol), stemphyltoxins I-IV, stemphyperylenol, stemphytriol, 7-epi-8-hydroxyaltertoxin I, and 6-epi-stemphytriol are mycotoxins derived from perylene quinone, for which the absolute configuration was not known. Electronic circular dichroism (ECD) spectra were calculated for these compounds and compared with measured spectra of altertoxins I-III, alteichin, and stemphyltoxin III and with reported Cotton effects. Specific rotations were calculated and compared with reported specific rotations. The absolute configuration of all the toxins, except for stemphyltoxin IV, could thus be determined. The validity of the assignment was high whenever reported ECD data were available for comparison, and the validity was lower when the assignment was based only on the comparison of calculated and reported specific rotations. ECD spectra are intrinsically different for toxins with a biphenyl substructure and for toxins derived from dihydroanthracene.

  17. Microspacecraft and Earth observation: Electrical Field (ELF) measurement project

    Science.gov (United States)

    1990-01-01

    There is a need for an inexpensive, extensive, long-lasting global electric field measurement system (ELF). The primary performance driver of this mission is the need to measure the attitude of each spacecraft in the Earth's electric field very accurately. In addition, it is necessary to know the electric charge generated by the satellite as it crosses the magnetic field lines (E equals V times B). In order to achieve the desired global coverage, a constellation of about 50 satellites in at least 18 different orbits will be used. To reduce the cost of each satellite, off-the-shelf, proven technology will be used whenever possible. Researchers have set a limit of $500,000 per satellite. Researchers expect the program cost, including the deployment of the entire constellation, to be less than $100 million. The minimum projected mission life is five years.

  18. Hybrid spherical particle field measurement based on interference technology

    Science.gov (United States)

    Sun, Jinlu; Zhang, Hongxia; Li, Jiao; Zhou, Ye; Jia, Dagong; Liu, Tiegen

    2017-03-01

    Interferometric particle imaging is widely used in particle size measurement. Conventional algorithms, which focus on single size particle fields, have difficulties in extracting each interference fringe in a hybrid spherical particle field due to the noise. To solve this problem, an iterative mean filter (IMF) algorithm is proposed. Instead of the specific mean filter template coefficient, the noise is reduced by iterating the calculation results under different template coefficients. The average value of the calculation results excluding the gross error is output as the final result. The effect of different template coefficients are simulated, furthermore, the value range of template coefficients has been analyzed. The interferogram of the hybrid spherical particle field from 21.3 µm to 57.9 µm is processed by the conventional algorithms with specific template coefficients of 2, 8, 12 and the IMF algorithm. The corresponding measurement errors are 17.22%, 10.69%, 9.04% and 5.11%. The experimental results show that the IMF algorithm would reduce measurement error, and could be potentially applied in particle field measurement.

  19. A.c. magnetic-field measurements using the fluxgate

    DEFF Research Database (Denmark)

    Ripka, Pavel; Primdahl, Fritz; Nielsen, Otto V

    1995-01-01

    Fluxgate sensors are mostly used in closed-loop d.c. magnetometer systems; they can also measure alternating fields up to severalkilohertz, either in open-loop mode or from an error signal in the slow-feedback loop as in the Thunderstorm rocket magnetometer, which has 0.1 nT resolution up to 3 k...

  20. Wideband scalable probe for Spherical Near-Field Antenna measurements

    DEFF Research Database (Denmark)

    Kim, Oleksiy S.; Pivnenko, Sergey; Breinbjerg, Olav

    2011-01-01

    The paper presents a design of an open-boundary quad-ridged horn to be used as a wideband scalable dual-linearly polarized probe for spherical near-field antenna measurements. With a new higher-order probe correction technique developed at the Technical University of Denmark, the probe will enabl...

  1. Simple System to Measure the Earth's Magnetic Field

    Science.gov (United States)

    Akoglu, R.; Halilsoy, M.; Mazharimousavi, S. Habib

    2010-01-01

    Our aim in this proposal is to use Faraday's law of induction as a simple lecture demonstration to measure the Earths magnetic field (B). This will also enable the students to learn about how electric power is generated from rotational motion. Obviously the idea is not original, yet it may be attractive in the sense that no sophisticated devices…

  2. Measurement of incident sound power using near field acoustic holography

    DEFF Research Database (Denmark)

    Jacobsen, Finn; Tiana Roig, Elisabet

    2009-01-01

    The conventional method of measuring the insertion loss of a partition relies on an assumption of the sound field in the source room being diffuse and the classical relation between the spatial average of the mean square pressure in the source room and the incident sound power per unit area...

  3. 47 CFR 73.314 - Field strength measurements.

    Science.gov (United States)

    2010-10-01

    ..., or a graph on which the distribution of measured field strength values is plotted. (vi) A list of... and vertical plane patterns of the transmitting antenna should be submitted. (iv) A list of calibrated... location, after equipment calibration and elevation of the antenna, a check is made to determine...

  4. Functional Measurement in the Field of Empirical Bioethics

    Science.gov (United States)

    Mullet, Etienne; Sorum, Paul C.; Teysseire, Nathalie; Nann, Stephanie; Martinez, Guadalupe Elizabeth Morales; Ahmed, Ramadan; Kamble, Shanmukh; Olivari, Cecilia; Sastre, Maria Teresa Munoz

    2012-01-01

    We present, in a synthetic way, some of the main findings from five studies that were conducted in the field of empirical bioethics, using the Functional Measurement framework. These studies were about (a) the rationing of rare treatments, (b) adolescents' abortions, (c) end-of-life decision-making regarding damaged neonates, (d) end-of-life…

  5. Planar Near-Field Measurements of Ground Penetrating Radar Antennas

    DEFF Research Database (Denmark)

    Meincke, Peter; Hansen, Thorkild

    2004-01-01

    Planar near-field measurements are formulated for a general ground penetrating radar (GPR) antenna. A total plane-wave scattering matrix is defined for the system consisting of the GPR antenna and the planar air-soil interface. The transmitting spectrum of the GPR antenna is expressed in terms...

  6. Spherical wave rotation in spherical near-field antenna measurements

    DEFF Research Database (Denmark)

    Wu, Jian; Larsen, Flemming Holm; Lemanczyk, J.

    1991-01-01

    The rotation of spherical waves in spherical near-field antenna measurement is discussed. Considering the many difficult but interesting features of the rotation coefficients, an efficient rotation scheme is derived. The main feature of the proposed scheme is to ignore the calculation of the very...

  7. Electric and magnetic field measurements. Annual report 80

    Energy Technology Data Exchange (ETDEWEB)

    McKnight, R.H.; Kotter, F.R.; Misakian, M.; Ortiz, P.

    1981-02-01

    The NBS program is concerned with developing methods for evaluating and calibrating instrumentation for use in measuring the electric field and various ion-related electrical quantities in the vicinity of high-voltage direct current (HVDC) transmission lines and in apparatus designed to simulate the transmission line environment.

  8. Preliminary field measurement of cotton fiber micronaire by portable NIR

    Science.gov (United States)

    The decline of the U.S. textile industry has led to the dramatic increase in the export of U.S. cotton. Improved quality measurement systems are needed to successfully compete in the global marketplace. One key need is the development of new breeder/producer quality tools for field and at-line mea...

  9. In-situ measurements in Vesivehmaa air field - STUK team

    Energy Technology Data Exchange (ETDEWEB)

    Markkanen, M.; Honkamaa, T.; Niskala, P. [Finnish Centre for Radiation and Nuclear Safety, Helsinki (Finland)

    1997-12-31

    Nineteen in-situ gamma-ray spectrometric measurements were performed in Vesivehmaa air field on 17th August 1995. The results for {sup 137}Cs and natural radionuclides are in good agreement with the results from soil sampling and laboratory analyses. (au).

  10. Landslide hazard assessment and mitigation measures in Philippine geothermal fields

    Energy Technology Data Exchange (ETDEWEB)

    Leynes, R.D.; Pioquinto, W.P.C.; Caranto, J.A. [PNOC Energy Development Corporation, Fort Bonifacio (Philippines)

    2005-04-01

    Simple, yet reliable, field criteria have been developed and are being used to qualitatively assess slope instability and slope failure potential in Philippine geothermal fields. Based on a hazard assessment classification of slopes along corridor facilities, sites for implementation of engineering measures are selected. Two case studies are presented. In Mindanao field, the ''very high-risk'' classification of an area resulted in the installation of pipe shelters, which subsequently shielded a section of a pipeline from landslides. Follow-up monitoring is also conducted using cheap, locally fabricated tools, such as surface extensometers. This is being done in Leyte field, where a landslide has threatened a transmission line tower. (author)

  11. Project Vanguard Magnetic-Field Instrumentation and Measurements

    Science.gov (United States)

    Heppner, J. P.; Storarik, J. D.; Shapiro, I. R.; Cain, J. C.

    1960-01-01

    The Vanguard III Satellite, 1959 Eta, placed in orbit on September 18, 1959, contained a proton precessional magnetometer for magnetic-field studies of exceptional accuracy. Throughout the 85 days of battery life, the instrumentation functioned according to plan. Measurements of the absolute total field were obtained in the meridian belts of Minitrack stations at altitudes 510 to 3750 kilometers and at latitudes +/- 33.4 degrees. Surface magnetic observatories were operated at eight of the Minitrack stations to furnish correlative information. This paper reviews briefly the instrumentation employed in these experiments, and the data collection and reduction procedures. Emphasis is given to results from a preliminary analysis. Specifically, this analysis bears on the accuracy of computed fields, the stability of the earth's field in space, the Capetown anomaly, and magnetic-storm effects.

  12. Electric Field Measurements During the Genesis and Rapid Intensification Processes (GRIP) Field Program

    Science.gov (United States)

    Bateman, Monte G.; Blakeslee, Richard J.; Mach, Douglas M.

    2010-01-01

    During the Genesis and Rapid Intensification Processes (GRIP) field program, a system of 6 electric field mills was flown on one of NASA's Global Hawk aircraft. We placed several mills on the aircraft to enable us to measure the vector electric field. We created a distributed, ethernet-connected system so that each sensor has its own embedded Linux system, complete with web server. This makes our current generation system fully "sensor web enabled." The Global Hawk has several unique qualities, but relevant to quality storm electric field measurements are high altitude (20 km) and long duration (20-30 hours) flights. There are several aircraft participating in the GRIP program, and coordinated measurements are happening. Lightning and electric field measurements will be used to study the relationships between lightning and other storm characteristics. It has been long understood that lightning can be used as a marker for strong convective activity. Past research and field programs suggest that lightning flash rate may serve as an indicator and precursor for rapid intensification change in tropical cyclones and hurricanes. We have the opportunity to sample hurricanes for many hours at a time and observe intensification (or de-intensification) periods. The electrical properties of hurricanes during such periods are not well known. American

  13. LIDAR Wind Speed Measurements of Evolving Wind Fields

    Energy Technology Data Exchange (ETDEWEB)

    Simley, E.; Pao, L. Y.

    2012-07-01

    Light Detection and Ranging (LIDAR) systems are able to measure the speed of incoming wind before it interacts with a wind turbine rotor. These preview wind measurements can be used in feedforward control systems designed to reduce turbine loads. However, the degree to which such preview-based control techniques can reduce loads by reacting to turbulence depends on how accurately the incoming wind field can be measured. Past studies have assumed Taylor's frozen turbulence hypothesis, which implies that turbulence remains unchanged as it advects downwind at the mean wind speed. With Taylor's hypothesis applied, the only source of wind speed measurement error is distortion caused by the LIDAR. This study introduces wind evolution, characterized by the longitudinal coherence of the wind, to LIDAR measurement simulations to create a more realistic measurement model. A simple model of wind evolution is applied to a frozen wind field used in previous studies to investigate the effects of varying the intensity of wind evolution. LIDAR measurements are also evaluated with a large eddy simulation of a stable boundary layer provided by the National Center for Atmospheric Research. Simulation results show the combined effects of LIDAR errors and wind evolution for realistic turbine-mounted LIDAR measurement scenarios.

  14. Stress-energy tensor of the quantized massive scalar field in spherically symmetric, topological and lukewarm black hole configurations in D =4 and D =5

    Science.gov (United States)

    Matyjasek, Jerzy

    2016-10-01

    In this paper, using the general Schwinger-DeWitt approach, we construct the approximate stress-energy tensor of the quantized massive scalar field with arbitrary curvature coupling in D =4 and D =5 classical spacetimes of the electrically charged static black holes with the cosmological constant. Depending on the sign of the cosmological constant we consider both spherically symmetric and topological spacetimes with the special emphasis put on the extremal and ultraextremal configurations. Moreover, we analyze the geometries of the closest vicinity of the degenerate horizons, which topologically are the product of the maximally symmetric subspaces. We solve the semiclassical Einstein field equations for such product spacetimes. Since the transformation k →-k and f''→-f'' leaves the equations unchanged, where k is the curvature of the (D -2 )-dimensional subspace and f'' is the second derivative of the metric potential at the degenerate horizon, it suffices to consider only the spherically symmetric case. It is shown that in four and five dimensions there are forbidden sectors of the parameter space.

  15. Microscopic Faraday rotation measurement system using pulsed magnetic fields.

    Science.gov (United States)

    Egami, Shigeki; Watarai, Hitoshi

    2009-09-01

    Microscopic Faraday rotation measurement system using a pulsed magnetic field has been constructed, which can be applied to micron sized diamagnetic and paramagnetic materials. A pulsed magnetic coil could generate a maximum magnetic flux density of about 12 T. The performance of the microscopic Faraday rotation apparatus was demonstrated by the measurement of the Verdet constant V of a polystyrene particle, after the calibration of the pulsed magnetic flux density using a glass plate as a standard material. Also, the magneto-optical rotation dispersion of some diamagnetic substances have been measured and analyzed with V=alambda(-2)+b. The values of a and b were compared to their magnetic susceptibilities.

  16. Measuring cosmic magnetic fields by rotation measure-galaxy cross-correlations in cosmological simulations

    CERN Document Server

    Stasyszyn, F; Dolag, K; Beck, R; Donnert, J

    2010-01-01

    Using cosmological MHD simulations of the magnetic field in galaxy clusters and filaments we evaluate the possibility to infer the magnetic field strength in filaments by measuring cross-correlation functions between Faraday Rotation Measures (RM) and the galaxy density field. We also test the reliability of recent estimates considering the problem of data quality and Galactic foreground (GF) removal in current datasets. Besides the two self-consistent simulations of cosmological magnetic fields based on primordial seed fields and galactic outflows analyzed here, we also explore a larger range of models scaling up the resulting magnetic fields of one of the simulations. We find that, if an unnormalized estimator for the cross-correlation functions and a GF removal procedure is used, the detectability of the cosmological signal is only possible for future instruments (e.g. SKA and ASKAP). However, mapping of the observed RM signal to the underlying magnetization of the Universe (both in space and time) is an e...

  17. Assessing Counter-Terrorism field training with multiple behavioral measures.

    Science.gov (United States)

    Spiker, V Alan; Johnston, Joan H

    2013-09-01

    Development of behavioral pattern recognition and analysis skills is an essential element of Counter-Terrorism training, particularly in the field. Three classes of behavioral measures were collected in an assessment of skill acquisition during a US Joint Forces Command-sponsored course consisting of Combat Tracking and Combat Profiling segments. Measures included situational judgment tests, structured behavioral observation checklists, and qualitative assessments of the emergence of specific knowledge-skills-attitudes over the course of the training. The paper describes statistical evidence across the three types of measures that indicate that behavioral pattern recognition and analysis skills were successfully acquired by most students (a mix of Army and civilian law enforcement personnel) during the field training exercises. Implications for broader training of these critical skills are also discussed.

  18. Adhesion Force Measurements of Polymer Particles by Detachment Field Method

    Institute of Scientific and Technical Information of China (English)

    Masashi Nagayama; Nobuyasu Sakurai; Tatsuaki Wada; Manabu Takeuchi

    2004-01-01

    The adhesion force distributions of polymer particles to aluminum substrates were measured by the detachment field method. Polymer particles with conducting surface treatment were used for the measurements.Further the conventional detachment field method was modified to be applicable to the adhesion force measurements of a single particle. The adhesion force of the polymer particles increased with an increase in relative humidity. The surface roughness of the substrate influenced the adhesion forces of particles significantly. The influence of the CF4 plasma treatment of the polymer particles and thin layer coating of the substrate surface on the adhesion forces of the polymer particles was also studied, and factors affecting adhesion forces of polymer particles are discussed.

  19. Measurement of incident sound power using near field acoustic holography

    DEFF Research Database (Denmark)

    Jacobsen, Finn; Tiana Roig, Elisabet

    2009-01-01

    ; and it has always been regarded as impossible to measure the sound power that is incident on a wall directly. This paper examines a new method of determining this quantity from sound pressure measurements at positions on the wall using ‘statistically optimised near field acoustic holography’ (SONAH......The conventional method of measuring the insertion loss of a partition relies on an assumption of the sound field in the source room being diffuse and the classical relation between the spatial average of the mean square pressure in the source room and the incident sound power per unit area......). The purpose is to examine whether one should use a correction similar to the well-known ‘Waterhouse correction’ when the incident sound power is deduced from the sound pressure in the source room....

  20. New insights into chromospheric structures from vector magnetic field measurements

    Science.gov (United States)

    Lagg, A.

    During the last decade advances in instrumentation atomic physics and modeling have greatly improved the access to the chromospheric magnetic field vector High sensitivity polarimeters like the Tenerife Infrared Polarimeter TIP2 VTT or the Spectro-Polarimeter for Infrared and Optical Regions SPINOR HAO lead to reliable Zeeman measurements using the He I 10830 nm triplet Theoretical modeling of the Hanle and the Paschen Back effect helped to significantly improve the analysis of polarization measurements in this triplet allowing to directly visualize the magnetic structure of spicules polar prominences and active regions In this presentation I will summarize the results of chromospheric magnetic field measurements using this interesting triplet obtained in the last couple of years and discuss the great potential it has to further uncover the complex structure of the chromosphere

  1. Magnetic field measurements near stand-alone transformer stations.

    Science.gov (United States)

    Kandel, Shaiela; Hareuveny, Ronen; Yitzhak, Nir-Mordechay; Ruppin, Raphael

    2013-12-01

    Extremely low-frequency (ELF) magnetic field (MF) measurements around and above three stand-alone 22/0.4-kV transformer stations have been performed. The low-voltage (LV) cables between the transformer and the LV switchgear were found to be the major source of strong ELF MFs of limited spatial extent. The strong fields measured above the transformer stations support the assessment method, to be used in future epidemiological studies, of classifying apartments located right above the transformer stations as highly exposed to MFs. The results of the MF measurements above the ground around the transformer stations provide a basis for the assessment of the option of implementing precautionary procedures.

  2. Critical Configuration and Physics Measurements for Assemblies of U(93.15)O2 Fuel Rods (1.506-cm Pitch)

    Energy Technology Data Exchange (ETDEWEB)

    Margaret A. Marshall

    2013-03-01

    A series of critical experiments were completed from 1962–1965 at Oak Ridge National Laboratory’s (ORNL’s) Critical Experiments Facility (CEF) in support of the Medium-Power Reactor Experiments (MPRE) program. In the late 1950s, efforts were made to study “power plants for the production of electrical power in space vehicles.”(a) The MPRE program was a part of those efforts and studied the feasibility of a stainless-steel system, boiling potassium 1 MW(t), or about 140 kW(e), reactor. The program was carried out in [fiscal years] 1964, 1965, and 1966. A summary of the program’s effort was compiled in 1967.a The delayed critical experiments were a mockup of a small, potassium-cooled space power reactor for validation of reactor calculations and reactor physics methods. Initial experiments, performed in November and December of 1962, consisted of a core of unmoderated stainless-steel tubes, each containing 26 UO2 fuel pellets, surrounded by a graphite reflector. Measurements were performed to determine critical reflector arrangements, relative fission-rate distributions, and cadmium ratio distributions. Subsequent experiments used beryllium reflectors and also measured the reactivity for various materials placed in the core. “The [assemblies were built] on [a] vertical assembly machine so that the movable part was the core and bottom reflector” (see Reference 1). The experiment studied in this evaluation was the second of the series and had the fuel rods in a 1.506-cm-triangular pitch. One critical configuration was found (see Reference 3). Once the critical configuration had been achieved, various measurements of reactivity, relative axial and radial activation rates of 235U,bc and cadmium ratios were performed. The cadmium ratio, reactivity, and activation rate measurements performed on the critical configuration are described in Sections 1.3, 1.4, and 1.7, respectively.

  3. A Comprehensive Method of Estimating Electric Fields from Vector Magnetic Field and Doppler Measurements

    CERN Document Server

    Kazachenko, Maria D; Welsch, Brian T

    2014-01-01

    Photospheric electric fields, estimated from sequences of vector magnetic field and Doppler measurements, can be used to estimate the flux of magnetic energy (the Poynting flux) into the corona and as time-dependent boundary conditions for dynamic models of the coronal magnetic field. We have modified and extended an existing method to estimate photospheric electric fields that combines a poloidal-toroidal (PTD) decomposition of the evolving magnetic field vector with Doppler and horizontal plasma velocities. Our current, more comprehensive method, which we dub the "{\\bf P}TD-{\\bf D}oppler-{\\bf F}LCT {\\bf I}deal" (PDFI) technique, can now incorporate Doppler velocities from non-normal viewing angles. It uses the \\texttt{FISHPACK} software package to solve several two-dimensional Poisson equations, a faster and more robust approach than our previous implementations. Here, we describe systematic, quantitative tests of the accuracy and robustness of the PDFI technique using synthetic data from anelastic MHD (\\te...

  4. Measurement and Optimization of Metal-Nanoparticle-Induced Luminescence Enhancement Factors in a Crossed-Optical Fiber Configuration

    Directory of Open Access Journals (Sweden)

    Maria Veronica Rigo

    2010-01-01

    Full Text Available A crossed-optical-fiber configuration comprised of silver nanoparticles covalently attached to the core of an optical fiber and labeled with luminescent ruthenium molecules is reported. A second optical fiber was placed at right angle of the fiber containing the nanoparticle/ruthenium, to form a fiber-fiber junction, and it was used to detect the luminescence from the ruthenium molecules bound to the first fiber. To employ the effect of metal-enhanced luminescence, the ruthenium complex was kept at an appropriate distance from the nanoparticles by polyelectrolyte spacer layers. For silver nanospheres, nanotriangles and nanorods and for spacer-layer thicknesses from 2–14 nm luminescence-enhancement factors were determined. A 27-fold luminescence enhancement was found when the ruthenium complex was placed 4 nm from silver nanotriangles. Finally, a calibration curve for the oxygen dependence of luminescence intensities and lifetimes of ruthenium complex is presented suggesting that the oxygen sensing capabilities of the nanoengineered-ruthenium complex are maintained.

  5. Velocity field investigation inside a bulb turbine runner using endoscopic PIV measurements

    Science.gov (United States)

    Lemay, S.; Aeschlimann, V.; Fraser, R.; Ciocan, G. D.; Deschênes, C.

    2015-06-01

    The flow in the inter-blade channels of a bulb turbine was measured using endoscopic cameras integrated to a stereoscopic particle image velocimetry (S-PIV) system. This paper presents results from the measurement campaign and also provides some key conclusions based on the dataset. The technical aspect of the measurement configuration is addressed. The main focus is on the novelties and challenges brought by the use of endoscopic cameras to achieve S-PIV measurements between the runner blades. For the first time in hydraulic rotating machinery, velocity measurements covered 62 % of a rotor inter-blade flow. After outlining the techniques used, comparison with laser Doppler velocimetry measurements allows assessing the intrusiveness of the endoscopes. Then, some velocity field analyses are shown. First, the rotor-stator interaction is outlined as the influence of the guide vane wakes on the runner flow. The size, localization, strength and dissipation of those structures are inferred from the information coming from measurements. Finally, the PIV data allow the identification of a vortex located near the suction side of the blades and originating from the corner between the leading edge and the hub when operating the bulb turbine at part-load.

  6. Measuring the Earth's gravity field with cold atom interferometers

    CERN Document Server

    Carraz, Olivier; Massotti, Luca; Haagmans, Roger; Silvestrin, Pierluigi

    2015-01-01

    The scope of the paper is to propose different concepts for future space gravity missions using Cold Atom Interferometers (CAI) for measuring the diagonal elements of the gravity gradient tensor, the spacecraft angular velocity and the spacecraft acceleration. The aim is to achieve better performance than previous space gravity missions due to a very low white noise spectral behaviour of the CAI instrument and a very high common mode rejection, with the ultimate goals of determining the fine structures of the gravity field with higher accuracy than GOCE and detecting time-variable signals in the gravity field.

  7. Automated cyclotron magnetic field measurement at the University of Manitoba

    Science.gov (United States)

    Derenchuk, V.; Bruckshaw, J.; Gusdal, I.; Lancaster, J.; McIlwain, A.; Oh, S.; Pogson, R.; McKee, J. S. C.

    The magnetic field of the University of Manitoba compact cyclotron has been measured in high vacuum by polar scanning with 52 flip coils. This was a unique invacuo operation was required because the Curie effect on invar material is used to trim the field. The data acquisition controller was a Digital Equipment Corporation LSI-11 with CAMAC and IEEE-488 interfaces. Filtering, display and conventional equilibrium orbit analysis were performed off-line by means of a VAX-11/750 computer. A description of the apparatus and software is given.

  8. Satellite measurements of the earth's crustal magnetic field

    Science.gov (United States)

    Schnetzler, C. C.

    1989-01-01

    The literature associated with the Magsat mission has evaluated the capabilities and limitations of satellite measurements of the earth's crustal magnetic field, and demonstrated that there exists a 300-3000 km magnetic field, related to major features in the earth's crust, which is primarily caused by induction. Due to its scale and sensitivity, satellite data have been useful in the development of models for such large crustal features as subduction zones, submarine platforms, continental accretion boundaries, and rifts. Attention is presently given to the lack of agreement between laboratory and satellite estimates of lower crustal magnetization.

  9. Low magnetic Johnson noise electric field plates for precision measurement

    CERN Document Server

    Rabey, I M; Hinds, E A; Sauer, B E

    2016-01-01

    We describe a parallel pair of high voltage electric field plates designed and constructed to minimise magnetic Johnson noise. They are formed by laminating glass substrates with commercially available polyimide (Kapton) tape, covered with a thin gold film. Tested in vacuum, the outgassing rate is less than $5\\times10^{-5}$ mbar.l/s. The plates have been operated at electric fields up to 8.3 kV/cm, when the leakage current is at most a few hundred pA. The design is discussed in the context of a molecular spin precession experiment to measure the permanent electric dipole moment of the electron.

  10. Field Geologist: An Android App for Measuring Rock Outcroppings

    Science.gov (United States)

    Baird, J.; Chiu, M. T.; Huang, X.; de Lanerolle, T. R.; Morelli, R.; Gourley, J. R.

    2011-12-01

    Field geologist is a mobile Android app that measures, plots, and exports strike and data in the field. When the phone is placed on the steepest part of the rock, it automatically detects dip, string, latitude and longitude. It includes a drop-down menu to record the type of rock. The app's initial screen displays a compass with an interior dip/strike symbol that always points toward the dip direction. Tapping the compass stores a data point in the phone's database. The points can be displayed on a Google map and uploaded to a server, from where they can be retrieved in CSV format and imported into a spreadsheet.

  11. Measurement and reconstruction of the BEBC magnetic field map

    CERN Document Server

    Häbel, E; Wittgenstein, F

    1973-01-01

    The superconducting magnet of the Big European Bubble Chamber (BEBC) has been excited with currents up to 5035 A corresponding to a magnetic induction of 3.1 Tesla at the center of the chamber. Since one expected that during the charging of the magnet coils long time constant eddy currents would be induced by the varying radial field components, a system of 181 Hall-probes was installed on the boundary of the chamber body allowing to survey the magnetic field map. This Hall-probe system together with an NMR-probe (nuclear magnetic resonance) enabled us to measure and reconstruct to an accuracy of better than 0.1the field map of BEBC, which in itself is uniform to within 3 191332nside the visible fiducial volume of the Chamber. Direct evidence was also given for field map distortions due to the eddy current field which amounted to about 0.723420f the maximum recorded field values at the chamber center. (7 refs).

  12. Measurement and reconstruction of the BEBC magnetic field map

    CERN Document Server

    Häbel, E; Wittgenstein, F

    1973-01-01

    The superconducting magnet of the Big European Bubble Chamber (BEBC) has been excited with currents up to 5035 A corresponding to a magnetic induction of 3.1 Tesla at the center of the chamber. Since one expected that during the charging of the magnet coils long time constant eddy currents would be induced by the varying radial field components, a system of 181 Hall-probes was installed on the boundary of the chamber body allowing to survey the magnetic field map. This Hall-probe system together with an NMR-probe (nuclear magnetic resonance) enabled us to measure and reconstruct to an accuracy of better than 0.1% the field map of BEBC, which in itself is uniform to within 3% inside the visible fiducial volume of the Chamber. Direct evidence was also given for field map distortions due to the eddy current field which amounted to about 0.7% of the maximum recorded field values at the chamber center. (7 refs).

  13. Modal measurements and propeller field excitation on acoustic full scale mockup of SAAB 340 aircraft

    Science.gov (United States)

    Gustavsson, Lars

    1992-06-01

    The acoustic mockup of the cabin SAAB 340 aircraft was measured in an anechoic chamber concerning modal parameters and operating deflection shapes. The mockup was excited with vibration shakers at the fuselage for modal estimation and with a ring of loudspeakers around the fuselage to generate propeller fields for operating deflection shapes. Two cases of structure configuration were used at the measurements; one consisting of only the fuselage, without trimpanels and floorpanels and one case with trimpanels and floorpanels. Modal measurements were done with excitation on a frame of the fuselage at the propeller plane. The modes were estimated for the individual components; fuselage, trimpanels, floorpanels, and soundfield in the cabin. The modes of the fuselage were compared with the acoustic models in the cabin concerning possible coupling effects. With the loudspeakering, the sound field from the left and the right propeller were generated at a blade passage frequency of 81.9 Hz and its first harmonic. Operating deflection shapes of fuselage, panels, and cabin acoustic were estimated. The results from the measurements could be used to verify a finite element model and as a tool for developing acoustic noise control systems.

  14. Field Measurements and Pullout Tests of Reinforced Earth Retaining Wall

    Institute of Scientific and Technical Information of China (English)

    陈群; 何昌荣; 朱分清

    2004-01-01

    In this paper, field measurements and pullout tests of a new type of reinforced earth retaining wall, which is reinforced by trapezoid concrete blocks connected by steel bar, are described. Field measurements included settlements of the earth fill, tensile forces in the ties and earth pressures on the facing panels during the construction and at completion. Based on the measurements, the following statements can be made: ( 1 ) the tensile forces in the ties increased with the height of backfill above the tie and there is a tensile force crest in most ties; (2) at completion, the measured earth pressures along the wall face were between the values of the active earth pressures and the pressures at rest; (3) larger settlements occurred near the face of the wall where a zone of drainage sand and gravel was not compacted properly and smaller settlements occurred in the well-compacted backfill. The results of field pullout tests indicated that the magnitudes of pullout resistances as well as tensile forces induced in the ties were strongly influenced by the relative displacements between the ties and the backfill, and pullout resistances increased with the height of backfill above the ties and the length of ties.

  15. Configuration entropy of fractal landscapes

    National Research Council Canada - National Science Library

    Rodríguez‐Iturbe, Ignacio; D'Odorico, Paolo; Rinaldo, Andrea

    1998-01-01

    .... The spatial arrangement of two‐dimensional images is found to be an effective way to characterize fractal landscapes and the configurational entropy of these arrangements imposes demanding conditions for models attempting to represent these fields.

  16. Field Measurements of Terrestrial and Martian Dust Devils

    Science.gov (United States)

    Murphy, Jim; Steakley, Kathryn; Balme, Matt; Deprez, Gregoire; Esposito, Francesca; Kahanpää, Henrik; Lemmon, Mark; Lorenz, Ralph; Murdoch, Naomi; Neakrase, Lynn; Patel, Manish; Whelley, Patrick

    2016-11-01

    Surface-based measurements of terrestrial and martian dust devils/convective vortices provided from mobile and stationary platforms are discussed. Imaging of terrestrial dust devils has quantified their rotational and vertical wind speeds, translation speeds, dimensions, dust load, and frequency of occurrence. Imaging of martian dust devils has provided translation speeds and constraints on dimensions, but only limited constraints on vertical motion within a vortex. The longer mission durations on Mars afforded by long operating robotic landers and rovers have provided statistical quantification of vortex occurrence (time-of-sol, and recently seasonal) that has until recently not been a primary outcome of more temporally limited terrestrial dust devil measurement campaigns. Terrestrial measurement campaigns have included a more extensive range of measured vortex parameters (pressure, wind, morphology, etc.) than have martian opportunities, with electric field and direct measure of dust abundance not yet obtained on Mars. No martian robotic mission has yet provided contemporaneous high frequency wind and pressure measurements. Comparison of measured terrestrial and martian dust devil characteristics suggests that martian dust devils are larger and possess faster maximum rotational wind speeds, that the absolute magnitude of the pressure deficit within a terrestrial dust devil is an order of magnitude greater than a martian dust devil, and that the time-of-day variation in vortex frequency is similar. Recent terrestrial investigations have demonstrated the presence of diagnostic dust devil signals within seismic and infrasound measurements; an upcoming Mars robotic mission will obtain similar measurement types.

  17. Measuring the Earth’s Magnetic Field from Space

    DEFF Research Database (Denmark)

    Olsen, Nils; Hulot, G.; Sabaka, T. J.

    2010-01-01

    Observations of the Earth’s magnetic field from low-Earth orbiting (LEO) satellites started very early on, more than 50 years ago. Continuous such observations, relying on more advanced technology and mission concepts, have however only been available since 1999. The unprecedented time......-space coverage of this recent data set opened revolutionary new possibilities for monitoring, understanding and exploring the Earth’s magnetic field. In the near future, the three-satellite Swarm constellation concept to be launched by ESA, will not only ensure continuity of such measurements, but also provide...... enhanced possibilities to improve on our ability to characterize and understand the many sources that produce this field. In the present paper we review and discuss the advantages and drawbacks of the various LEO space magnetometry concepts that have been used so far, and report on the motivations that led...

  18. Generation and measurement of pulsed high magnetic field

    CERN Document Server

    Jana, S

    2000-01-01

    Pulsed magnetic field has been generated by discharging a capacitor bank through a 5-layer air-core solenoid. The strength of the magnetic field at its peak has been measured using the voltage induced in various pick-up coils, and also from the Zeeman splitting of an ion having a known g value. Synchronizing a xenon flash at the peak of the magnetic field, this lab-made instrument has been made well suited to study the Zeeman effect, etc. at a temperature of 25 K. As an application of this setup, we have investigated the Zeeman splitting of the sup 4 I sub 9 sub / sub 2-> sup 4 G sub 5 sub / sub 2 transition of the Nd sup 3 sup + -doped CsCdCl sub 3 crystal at 7.8 T, and determined the splitting factors.

  19. Mean field limit for bosons and propagation of Wigner measures

    CERN Document Server

    Ammari, Z

    2008-01-01

    We consider the N-body Schr\\"{o}dinger dynamics of bosons in the mean field limit with a bounded pair-interaction potential. According to the previous work \\cite{AmNi}, the mean field limit is translated into a semiclassical problem with a small parameter $\\epsilon\\to 0$, after introducing an $\\epsilon$-dependent bosonic quantization. The limit is expressed as a push-forward by a nonlinear flow (e.g. Hartree) of the associated Wigner measures. These object and their basic properties were introduced in \\cite{AmNi} in the infinite dimensional setting. The additional result presented here states that the transport by the nonlinear flow holds for rather general class of quantum states in their mean field limit.

  20. The BOES spectropolarimeter for Zeeman measurements of stellar magnetic fields

    CERN Document Server

    Kim, Kang-Min; Valyavin, Gennady G; Plachinda, Sergei; Jang, Jeong Gyun; Jang, Be-Ho; Seong, Hyeon Cheol; Lee, Byeong-Cheol; Kang, Dong-Il; Park, Byeong-Gon; Yoon, Tae Seog; Vogt, Steven S

    2007-01-01

    We introduce a new polarimeter installed on the high-resolution fiber-fed echelle spectrograph (called BOES) of the 1.8-m telescope at the Bohyunsan Optical Astronomy Observatory, Korea. The instrument is intended to measure stellar magnetic fields with high-resolution (R $\\sim$ 60000) spectropolarimetric observations of intrinsic polarization in spectral lines. In this paper we describe the spectropolarimeter and present test observations of the longitudinal magnetic fields in some well-studied F-B main sequence magnetic stars (m_v < 8.8^m). The results demonstrate that the instrument has a high precision ability of detecting the fields of these stars with typical accuracies ranged from about 2G to a few tens of gauss.

  1. Electric Field Measurement of the Living Human Body for Biomedical Applications: Phase Measurement of the Electric Field Intensity

    Directory of Open Access Journals (Sweden)

    Ichiro Hieda

    2013-01-01

    Full Text Available The authors are developing a technique for conducting measurements inside the human body by applying a weak electric field at a radio frequency (RF. Low RF power is fed to a small antenna, and a similar antenna located 15–50 cm away measures the electric field intensity. Although the resolution of the method is low, it is simple, safe, cost-effective, and able to be used for biomedical applications. One of the technical issues suggested by the authors' previous studies was that the signal pattern acquired from measurement of a human body was essentially different from that acquired from a phantom. To trace the causes of this difference, the accuracy of the phase measurements was improved. This paper describes the new experimental system that can measure the signal phase and amplitude and reports the results of experiments measuring a human body and a phantom. The results were analyzed and then discussed in terms of their contribution to the phase measurement.

  2. Evaluation of a method for heat transfer measurements and thermal visualization using a composite of a heater element and liquid crystals. [thermal performance of turbine blade cooling configurations

    Science.gov (United States)

    Hippensteele, S. A.; Russell, L. M.; Stepka, F. S.

    1981-01-01

    Commercially available elements of a composite consisting of a plastic sheet coated with liquid crystal, another sheet with a thin layer of a conducting material (gold or carbon), and copper bus bar strips were evaluated and found to provide a simple, convenient, accurate, and low-cost measuring device for use in heat transfer research. The particular feature of the composite is its ability to obtain local heat transfer coefficients and isotherm patterns that provide visual evaluation of the thermal performances of turbine blade cooling configurations. Examples of the use of the composite are presented.

  3. The laser measurement technology of combustion flow field

    Science.gov (United States)

    Wang, Mingdong; Wang, Guangyu; Qu, Dongsheng

    2014-07-01

    The parameters of combustion flow field such as temperature, velocity, pressure and mole-fraction are of significant value in engineering application. The laser spectroscopy technology which has the non-contact and non- interference properties has become the most important method and it has more advantages than conventionally contacting measurement. Planar laser induced fluorescence (PLIF/LIF) is provided with high sensibility and resolution. Filtered Rayleigh scattering (FRS) is a good measurement method for complex flow field .Tunable diode laser absorption spectroscopy (TDLAS) is prosperity on development and application. This article introduced the theoretical foundation, technical principle, system structure, merits and shortages. It is helpful for researchers to know about the latest development tendency and do the related research.

  4. Torque measurements on ferrofluid cylinders in rotating magnetic fields

    Energy Technology Data Exchange (ETDEWEB)

    Rinaldi, Carlos [Department of Chemical Engineering, University of Puerto Rico, PO Box 9046, Mayagueez, PR 00680 (United States)]. E-mail: crinaldi@uprm.edu; Gutman, Fernando [Department of Chemical Engineering, University of Puerto Rico, PO Box 9046, Mayagueez, PR 00680 (United States); He Xiaowei [Laboratory for Electromagnetic and Electronic Systems, Department of Electrical Engineering and Computer Science, Massachusetts Institute of Technology, 77 Massachusetts Avenue, Cambridge, MA, 02139 (United States); Rosenthal, Adam D. [Laboratory for Electromagnetic and Electronic Systems, Department of Electrical Engineering and Computer Science, Massachusetts Institute of Technology, 77 Massachusetts Avenue, Cambridge, MA, 02139 (United States); Zahn, Markus [Laboratory for Electromagnetic and Electronic Systems, Department of Electrical Engineering and Computer Science, Massachusetts Institute of Technology, 77 Massachusetts Avenue, Cambridge, MA, 02139 (United States)

    2005-03-15

    We study the response of magnetic nanoparticle suspensions (ferrofluids) to uniform rotating magnetic fields generated by a two-pole three-phase magnetic induction motor stator winding. Measurements of the torque required to rotate a polycarbonate spindle submerged in ferrofluid subjected to co-rotating and counter-rotating fields yield experimental observations of negative magnetoviscosity in a cylindrical Couette geometry, conceptually similar to the observations of Bacri et al. (Phys. Rev. Lett. 75 (1995) 2128) in a Poiseuille flow under an oscillating magnetic field. Further measurements are presented for the torque required to restrain a spindle when it is (i) entirely filled with ferrofluid (ii) entirely surrounded with ferrofluid, and (iii) both entirely filled and surrounded with ferrofluid. Some of the results for the spindle either entirely filled or entirely surrounded with ferrofluid are compared to theoretical expressions obtained from the ferrohydrodynamic equations using a rigorous regular perturbation expansion in the small parameter {omega}{tau}, where {omega} is the applied field frequency and {tau} is the effective magnetic relaxation time of the suspension.

  5. The Effect of a Soap Film on a Catenary: Measurement of Surface Tension from the Triangular Configuration

    Science.gov (United States)

    Behroozi, F.; Behroozi, P. S.

    2011-01-01

    A chain assumes the well-known shape known as a catenary when it hangs loosely from two points in a gravitational field. The correct solution of the catenary was one of the early triumphs of the newly invented calculus of variations at the end of the 17th century. Here we revisit the catenary and show that, for a chain hanging from a horizontal…

  6. Experimental Measurement of Asymmetric Fluctuations of Poloidal Magnetic Field in Damavand Tokomak at Different Plasma Currents

    Science.gov (United States)

    Moslehi-Fard, Mahmoud; Alinejad, Naser; Rasouli, Chapar; Sadigzadeh, Asghar

    2012-08-01

    Toroidal and Poloidal magnetic fields have an important effect on the tokomak topology. Damavand Tokomak is a small size tokomak characterized with k = 1.2, B t = 1T, R 0 = 36 cm, maximum plasma current is about 35 KA with a discharge time of 21 ms. In this experimental work, the variation of poloidal magnetic field on the torodial cross section is measured and analyzed. In order to measure the polodial magnetic field, 18 probes were installed on the edge of tokomak plasma with ∆θ = 18°, while a limiter was installed inside the torus. Plasma current, I p, induces a polodial magnetic field, B p, smaller than the torodial magnetic field B t. Magnetic lines B produced as a combination of B t and B p, are localized on the nested toroidal magnetic surfaces. The presence of polodial magnetic field is necessary for particles confinement. Mirnov oscillations are the fluctuations of polodial magnetic field, detected by magnetic probes. Disrupted instability in Tokomak typically starts with mirnov oscillations which appear as fluctuations of polodial magnetic field and is detected by magnetic probes. Minor disruptions inside the plasma can contain principal magnetic islands and their satellites can cause the annihilation of plasma confinement. Production of thin layer of turbulent magnetic field lines cause minor disruption. Magnetic limiter may cause the deformation of symmetric equilibrium configuration and chaotic magnetic islands reveal in plasma occurring in thin region of chaotic field lines close to their separatrix. The width of this chaotic layer in the right side of poloidal profile of Damavand Tokomak is smaller than the width in the left side profile because of Shafranov displacement. Ergodic region in the left side of profile develops a perturbation on the magnetic polodial field lines, B p, that are greater in magnitude than that in the right side, although the values of B p on the left side are smaller than that on the right side of the profile. The Left

  7. Experimental studies on near-field holographic antenna measurement

    Science.gov (United States)

    Zuo, Yingxi; Xu, Linfen; An, Hongye; Sun, Jixian; Lou, Zheng; Yang, Ji; Zhang, Xuguo; Li, Zhenqiang; Lu, Dengrong; Pang, Xinghai; Li, Yang

    2016-07-01

    A near-field millimeter-wave holography system operating in the 3-mm waveband have been developed as a prototype for DATE5, a 5-m terahertz telescope proposed to be deployed at Dome A, Antarctica. Experimental measurements at 92 GHz have been made on a 1.45-m test antenna. During the night time at which the ambient temperature doesn't vary rapidly, a 75-minute repeatability (repeating measurement 3 times) of 2.3 μm rms has been achieved with an aperture resolution of 46 mm. A local surface change of known value is correctly detected. After long-time repeating measurements, thermal-induced feed displacement is also detected with an accuracy of approximately 20 μm. Random error factors of the experiment system are evaluated and their contributions to the derived surface error are also simulated, showing that relative poor pointing of the test antenna is the major factor limiting the measurement repeatability.

  8. Analysis and measurement of the 3D magnetic field in a rotating magnetic field driven FRC

    Science.gov (United States)

    Velas, K. M.; Milroy, R. D.

    2012-10-01

    A translatable three-axis probe was installed on TCSU shortly before its shutdown. The probe has 90 windings that simultaneously measure Br, Bθ, and Bz at 30 radial positions. Positioning the probe at multiple axial positions and taking multiple repeatable shots allows for a full r-z map of the magnetic field. Probe measurements are used to calculate the end-shorting torque and the rotating magnetic field (RMF) torque. The torque applied to the plasma is the RMF torque reduced by the shorting torque. An estimate of the plasma resistivity is made based on the steady state balance between the applied torque and the resistive torque. The steady state data from applying a 10 kHz low pass filter used in conjunction with data at the RMF frequency yields a map of the full 3D rotating field structure. Data from even- and odd-parity experiments will be presented. The NIMROD code has been adapted to simulate the TCSU experiment using boundary conditions adjusted to match both even- and odd-parity experimental conditions. A comparison of the n=0 components of the calculated fields to the 3-axis probe measurements shows agreement in the magnetic field structure of the FRC as well as in the jet region.

  9. Neutron Field Measurements in Phantom with Foil Activation Methods.

    Science.gov (United States)

    1986-11-29

    jI25 Ii III uumu ullli~ S....- - Lb - w * .qJ’ AD-A 192 122 ulJ. IL (pj DNA-TR-87- 10 N EUTRON FIELD MEASUREMENTS IN PHANTOM WITH FOIL ACTIVATION...SAND II Measurements in Phantom 6 4 The 5-Foil Neutron Dosimetry Method 29 5 Comparison of SAND II and Simple 5-Foil Dosimetry Method 34 6 Thermal ...quite reasonable. The monkey phantom spectrum differs from the NBS U-235 fission spectrum in that the former has a I/E tail plus thermal -neutron peak

  10. Planar Near-Field Measurements of Ground Penetrating Radar Antennas

    DEFF Research Database (Denmark)

    Meincke, Peter; Hansen, Thorkild

    2004-01-01

    Planar near-field measurements are formulated for a general ground penetrating radar (GPR) antenna. A total plane-wave scattering matrix is defined for the system consisting of the GPR antenna and the planar air-soil interface. The transmitting spectrum of the GPR antenna is expressed in terms...... of measurements obtained with a buried probe as the GPR antenna moves over a scan plane on the ground. A numerical example in which the scan plane is finite validates the expressions for the spectrum of the GPR antenna....

  11. Improved Reconstruction of Dipole Directions from Spherical Magnetic Field Measurements

    CERN Document Server

    Gerhards, Christian

    2016-01-01

    Reconstructing magnetizations from measurements of the generated magnetic potential is highly non-unique. The matter of uniqueness can be improved, but not entirely resolved, by the assumption that the magnetization is locally supported. Here, we focus on the case that the magnetization is additionally assumed to be induced by an ambient magnetic dipole field, i.e., the task is to reconstruct the dipole direction as well as the susceptibility of the magnetic material. We investigate uniqueness issues and provide a reconstruction procedure from given magnetic potential measurements on a spherical surface.

  12. Verifying a Simplified Fuel Oil Flow Field Measurement Protocol

    Energy Technology Data Exchange (ETDEWEB)

    Henderson, H.; Dentz, J.; Doty, C.

    2013-07-01

    The Better Buildings program is a U.S. Department of Energy program funding energy efficiency retrofits in buildings nationwide. The program is in need of an inexpensive method for measuring fuel oil consumption that can be used in evaluating the impact that retrofits have in existing properties with oil heat. This project developed and verified a fuel oil flow field measurement protocol that is cost effective and can be performed with little training for use by the Better Buildings program as well as other programs and researchers.

  13. Verifying a Simplified Fuel Oil Field Measurement Protocol

    Energy Technology Data Exchange (ETDEWEB)

    Henderson, Hugh [Advanced Residential Integrated Energy Solutions Collaborative (ARIES), New York, NY (United States); Dentz, Jordan [Advanced Residential Integrated Energy Solutions Collaborative (ARIES), New York, NY (United States); Doty, Chris [Advanced Residential Integrated Energy Solutions Collaborative (ARIES), New York, NY (United States)

    2013-07-01

    The Better Buildings program is a U.S. Department of Energy program funding energy efficiency retrofits in buildings nationwide. The program is in need of an inexpensive method for measuring fuel oil consumption that can be used in evaluating the impact that retrofits have in existing properties with oil heat. This project developed and verified a fuel oil flow field measurement protocol that is cost effective and can be performed with little training for use by the Better Buildings program as well as other programs and researchers.

  14. FUNCTIONAL MEASUREMENT IN THE FIELD OF ETHICS IN POLITICS

    OpenAIRE

    Mullet, Etienne; Institute of Advanced Studies (EPHE); López López, Wilson; Pontificia Universidad Javeriana; Kpanake, Lonzozou; Open University of Quebec at Montreal; Mukashema, Immaculée; University of Rwanda; Armange, Roseline; Institute of Advanced Studies; Kamble, Shanmukh; University of Karnataka; Guedez, Ana Gabriela; Jean-Jaurès University; Munoz Sastre, Maria Teresa; Jean-Jaurès University; Sorum, Paul C.; Albany Medical College; Nieto, Félix; University of Oporto; Pineda, Claudia

    2016-01-01

    We present, in a synthetic way, some of the main findings from ten studies that were conducted in the field of ethics in politics, using the Functional Measurement framework. These studies were about (a) Angolan and Mozambican people’s views about the legitimacy of military-humanitarian interventions, (b) French people’s perspectives regarding the government’s responsibility for the health of consumers of illicit substances, (c) Togolese people’s views about the acceptability of political amn...

  15. Precise measurement of effective oxygen diffusivity for microporous media containing moisture by review of galvanic cell oxygen absorber configuration

    OpenAIRE

    Koresawa, Ryo; Utaka, Yoshio

    2014-01-01

    The performance of polymer electrolyte fuel cells is influenced by moisture control in their gas diffusion layer (GDL). Therefore, to achieve suitable control, it is necessary to clarify the mass transfer characteristics within a GDL by high precision measurement of oxygen diffusivity. We have previously proposed that measurement of the effective oxygen diffusivity in a GDL containing moisture can be achieved using a galvanic cell oxygen absorber and demonstrated this to be an effective techn...

  16. Flow field study in a bulb turbine runner using LDV and endoscopic S-PIV measurements

    Science.gov (United States)

    Lemay, S.; Fraser, R.; Ciocan, G. D.; Aeschlimann, V.; Deschênes, C.

    2014-03-01

    The flow in the inter-blade channels of a bulb turbine was measured using two different techniques. The first involved a classical laser Doppler velocimetry (LDV) setup whereas the second integrated endoscopic cameras to a stereoscopic particle image velocimetry (S-PIV) system. This paper presents results from both measurement campaigns and also provides some key conclusions based on the two datasets. Before getting into the thick of the data though, the technical aspect of both measurement configurations is addressed. A quick overview of the LDV setup is presented, but the main focus is on the novelties and challenges brought by the use of endoscopic cameras to achieve S-PIV measurements between the runner blades. Endoscopic PIV systems have already led to successful measurements of flow fields in a few studies concerning turbomachinery, especially in aerodynamics. However, to the author's knowledge, the realisation of such measurements in a hydraulic turbine is a first. After this outline of the techniques used, the results and conclusions are shown. First, the influence of the guide vanes wakes on the runner flow is described. The size, localisation, strength and dissipation of those structures are inferred from the information coming from both measurement techniques. Then, a flow imbalance is assessed circumferentially. On another subject, the blade tip vortices are identified and characterized using the LDV data. The size, position and direction of rotation of those structures are all extracted from the measured flow field. Finally, the PIV data allows the identification of yet another vortex located near the suction side of the blades and originating from the corner between the leading edge and the hub when operating the bulb turbine at part load.

  17. The IMCA: A field instrument for uranium enrichment measurements

    Energy Technology Data Exchange (ETDEWEB)

    Gardner, G.H.; Koskelo, M.; Moeslinger, M. [Canberra Industries, Meriden, CT (United States); Mayer, R.L. II; McGinnis, B.R. [Lockheed Martin Utility Services, Piketon, OH (United States). Portsmouth Gaseous Diffusion Plant; Wishard, B. [International Atomic Energy Agency, Vienna (Austria)

    1996-12-31

    The IMCA (Inspection Multi-Channel Analyzer) is a portable gamma-ray spectrometer designed to measure the enrichment of uranium either in a laboratory or in the field. The IMCA consists of a Canberra InSpector Multi-Channel Analyzer, sodium iodide or a planar germanium detector, and special application software. The system possesses a high degree of automation. The IMCA uses the uranium enrichment meter principle, and is designed to meet the International Atomic Energy Agency (IAEA) requirements for the verification of enriched uranium materials. The IMCA is available with MGA plutonium isotopic analysis software or MGAU uranium analysis software as well. In this paper, the authors present a detailed description of the hardware and software of the IMCA system, as well as results from preliminary measurements testing compliance of IMCA with IAEA requirements using uranium standards and UF6 cylinders. Measurements performed on UF6 cylinders in the field under variable environmental conditions (temperatures ranging from 0 to 35 C) have shown that good results can be achieved. The enrichment of UF6 contained in the cylinder is determined by using calibration constants generated from an instrument calibration, using traceable uranium oxide standards, performed in the laboratory under controlled environmental conditions. The IMCA software is designed to make the necessary matrix and container corrections to ensure that accurate results are achieved in the field.

  18. Standard target sets for field sensor performance measurements

    Science.gov (United States)

    O'Connor, John D.; O'Shea, Patrick; Palmer, John E.; Deaver, Dawne M.

    2006-05-01

    The US Army Night Vision and Electronic Sensors Directorate (NVESD) Modeling and Simulation Division develops sensors models (FLIR 92, NV Therm, NV Therm IP) that predict the comparative performance of electro-optical sensors. The NVESD modeling branch developed a 12-vehicle, 12-aspect target signature set in 1998 with a known cycle criteria. It will be referred to as the 12-target set. This 12-target set has and will continue to be the modeling "gold standard" for laboratory human perception experiments supporting sensor performance modeling, and has been employed in dozens of published experiments. The 12-target set is, however, too costly for most acquisition field tests and evaluations. The authors developed an 8-vehicle 3-aspect target set, referred to as the 8- target set, and measured its discrimination task difficulty, (N50 and V50). Target identification (ID) range performance predictions for several sensors were made based on those V50/N50 values. A field collection of the 8-target set using those sensors provided imagery for a human perception study. The human perception study found excellent agreement between predicted and measured range performance. The goal of this development is to create a "silver standard" target set that is as dependable in measuring sensor performance as the "gold standard", and is affordable for Milestone A and other field trials.

  19. Gravitational spectra from direct measurements. [of surface field

    Science.gov (United States)

    Wagner, C. A.; Colombo, O. L.

    1979-01-01

    A simple rapid method is described for determining the spectrum of a surface field (in spherical harmonics) from harmonic analysis of direct (in situ) measurements along great circle arcs. The method is shown to give excellent overall trends (smoothed spectra) to very high degree from even a few short arcs of satellite data. Three examples are taken with perfect measurements of satellite tracking over a planet made up of hundreds of point masses using (1) altimetric heights from a low-orbiting spacecraft, (2) velocity (range rate) residuals between a low and a high satellite in circular orbits, and (3) range rate data between a station at infinity and a satellite in a highly eccentric orbit. In particular, the smoothed spectrum of the earth's gravitational field is determined to about degree 400(50-km half wavelength) from 1 x 1 deg gravimetry and the equivalent of 11 revolutions of GEOS 3 and Skylab altimetry. This measurement shows that there is about 46 cm of geoid height (rms worldwide) remaining in the field beyond degree 180.

  20. Real-time temperature field measurement based on acoustic tomography

    Science.gov (United States)

    Bao, Yong; Jia, Jiabin; Polydorides, Nick

    2017-07-01

    Acoustic tomography can be used to measure the temperature field from the time-of-flight (TOF). In order to capture real-time temperature field changes and accurately yield quantitative temperature images, two improvements to the conventional acoustic tomography system are studied: simultaneous acoustic transmission and TOF collection along multiple ray paths, and an offline iteration reconstruction algorithm. During system operation, all the acoustic transceivers send modulated and filtered wideband Kasami sequences simultaneously to facilitate fast and accurate TOF measurements using cross-correlation detection. For image reconstruction, the iteration process is separated and executed offline beforehand to shorten computation time for online temperature field reconstruction. The feasibility and effectiveness of the developed methods are validated in the simulation study. The simulation results demonstrate that the proposed method can reduce the processing time per frame from 160 ms to 20 ms, while the reconstruction error remains less than 5%. Hence, the proposed method has great potential in the measurement of rapid temperature change with good temporal and spatial resolution.

  1. High frequency electric field levels: An example of determination of measurement uncertainty for broadband measurements

    Directory of Open Access Journals (Sweden)

    Vulević Branislav

    2016-01-01

    Full Text Available Determining high frequency electromagnetic field levels in urban areas represents a very complex task, having in mind the exponential growth of the number of sources embodied in public cellular telephony systems in the past twenty years. The main goal of this paper is a representation of a practical solution in the evaluation of measurement uncertainty for in-situ measurements in the case of spatial averaging. An example of the estimation of the uncertainty for electric field strength broadband measurements in the frequency range from 3 MHz to 18 GHz is presented.

  2. Heat flux and plasma flow in the scrape off layer on the spherical tokamak QUEST with inboard poloidal field null configuration

    Science.gov (United States)

    Onchi, Takumi; Zushi, Hideki; Mishra, Kishore; Hanada, Kazuaki; Idei, Hiroshi; Nakamura, Kazuo; Fujisawa, Akihide; Nagashima, Yoshihiko; Hasegawa, Makoto; Kuzmin, Arseny; Nagaoka, Kenichi; QUEST Team

    2014-10-01

    Heat flux and plasma flow in the scrape off layer (SOL) are examined in the inboard poloidal null (IPN) configuration on the spherical tokamak (ST) QUEST. In the ST, trapped energetic electrons on the low field side are widely excursed from the last closed flux surface to SOL so that significant heat loss occurs. Interestingly, plasma flows in the core and the SOL are also observed in IPN though no inductive force like ohmic heating is applied. High heat flux (>1 MW/m2) and sonic flow (M > 1) in far-SOL arise in current ramp-up phase. In quasi-steady state, sawtooth-like oscillation of plasma current with 20 Hz has been observed. Heat flux and subsonic plasma flow in far-SOL are well correlated to plasma current oscillation. The toroidal Mach number largely increases from Mφ ~ 0.1 to ~ 0.5 and drops although the amplitude of plasma current is about 10% of that. Note that such flow modification occurs before plasma current crash, there may be some possibility that phenomena in the SOL or the edge trigger reactions in the core plasma. This work is supported by Grants-in-aid for Scientific Research (S24226020), NIFS Collaboration Research Program (NIFS12KUTR081), and the Collaborative Research Program of Research Institute for Applied Mechanics, Kyushu University.

  3. Advancement of an Infra-Red Technique for Whole-Field Concentration Measurements in Fluidized Beds

    Science.gov (United States)

    Medrano, Jose A.; de Nooijer, Niek C. A.; Gallucci, Fausto; van Sint Annaland, Martin

    2016-01-01

    For a better understanding and description of the mass transport phenomena in dense multiphase gas-solids systems such as fluidized bed reactors, detailed and quantitative experimental data on the concentration profiles is required, which demands advanced non-invasive concentration monitoring techniques with a high spatial and temporal resolution. A novel technique based on the selective detection of a gas component in a gas mixture using infra-red properties has been further developed. The first stage development was carried out using a very small sapphire reactor and CO2 as tracer gas. Although the measuring principle was demonstrated, the real application was hindered by the small reactor dimensions related to the high costs and difficult handling of large sapphire plates. In this study, a new system has been developed, that allows working at much larger scales and yet with higher resolution. In the new system, propane is used as tracer gas and quartz as reactor material. In this study, a thorough optimization and calibration of the technique is presented which is subsequently applied for whole-field measurements with high temporal resolution. The developed technique allows the use of a relatively inexpensive configuration for the measurement of detailed concentration fields and can be applied to a large variety of important chemical engineering topics. PMID:26927127

  4. Advancement of an Infra-Red Technique for Whole-Field Concentration Measurements in Fluidized Beds

    Directory of Open Access Journals (Sweden)

    Jose A. Medrano

    2016-02-01

    Full Text Available For a better understanding and description of the mass transport phenomena in dense multiphase gas-solids systems such as fluidized bed reactors, detailed and quantitative experimental data on the concentration profiles is required, which demands advanced non-invasive concentration monitoring techniques with a high spatial and temporal resolution. A novel technique based on the selective detection of a gas component in a gas mixture using infra-red properties has been further developed. The first stage development was carried out using a very small sapphire reactor and CO2 as tracer gas. Although the measuring principle was demonstrated, the real application was hindered by the small reactor dimensions related to the high costs and difficult handling of large sapphire plates. In this study, a new system has been developed, that allows working at much larger scales and yet with higher resolution. In the new system, propane is used as tracer gas and quartz as reactor material. In this study, a thorough optimization and calibration of the technique is presented which is subsequently applied for whole-field measurements with high temporal resolution. The developed technique allows the use of a relatively inexpensive configuration for the measurement of detailed concentration fields and can be applied to a large variety of important chemical engineering topics.

  5. A polarisation modulation scheme for measuring vacuum magnetic birefringence with static fields

    Energy Technology Data Exchange (ETDEWEB)

    Zavattini, G.; Ejlli, A. [Universita di Ferrara, Dipt. di Fisica e Scienze della Terra (Italy); INFN, Sezione di Ferrara (Italy); Della Valle, F. [Universita di Trieste, Dipt. di Fisica, Trieste (Italy); INFN, Sezione di Trieste, TS (Italy); Ruoso, G. [INFN, Lab. Nazionali di Legnaro (Italy)

    2016-05-15

    A novel polarisation modulation scheme for polarimeters based on Fabry-Perot cavities is presented. The application to the measurement of the magnetic birefringence of vacuum with the HERA superconducting magnets in the ALPS-II configuration is discussed. (orig.)

  6. Field measurements and analyses of environmental vibrations induced by high-speed Maglev.

    Science.gov (United States)

    Li, Guo-Qiang; Wang, Zhi-Lu; Chen, Suwen; Xu, You-Lin

    2016-10-15

    Maglev, offers competitive journey-times compared to the railway and subway systems in markets for which distance between the stations is 100-1600km owing to its high acceleration and speed; however, such systems may have excessive vibration. Field measurements of Maglev train-induced vibrations were therefore performed on the world's first commercial Maglev line in Shanghai, China. Seven test sections along the line were selected according to the operating conditions, covering speeds from 150 to 430km/h. Acceleration responses of bridge pier and nearby ground were measured in three directions and analyzed in both the time and frequency domain. The effects of Maglev train speed on vibrations of the bridge pier and ground were studied in terms of their peak accelerations. Attenuation of ground vibration was investigated up to 30m from the track centerline. Effects of guideway configuration were also analyzed based on the measurements through two different test sections with same train speed of 300km/h. The results showed that peak accelerations exhibited a strong correlation with both train speed and distance off the track. Guideway configuration had a significant effect on transverse vibration, but a weak impact on vertical and longitudinal vibrations of both bridge pier and ground. Statistics indicated that, contrary to the commonly accepted theory and experience, vertical vibration is not always dominant: transverse and longitudinal vibrations should also be considered, particularly near turns in the track. Moreover, measurements of ground vibration induced by traditional high-speed railway train were carried out with the same testing devices in Bengbu in the Anhui Province. Results showed that the Maglev train generates significantly different vibration signatures as compared to the traditional high-speed train. The results obtained from this paper can provide good insights on the impact of Maglev system on the urban environment and the quality of human life

  7. GHz measurements of correlated electron systems in high magnetic fields

    CERN Document Server

    Edwards, R S

    2002-01-01

    This Thesis presents experiments performed on the high-frequency conductivity of materials in high magnetic fields. The angle dependence of resonances measured in the millimetre-wave absorption is studied using a rotating resonant cavity system, and the frequency dependence is measured using transmission techniques and a tuneable resonant cavity. Chapter 1 introduces the materials. These include the crystalline organic metals, the layered superconductor Sr sub 2 RUO sub 4 and the quantum Ising ferromagnet LiHoF sub 4. In Chapters 2 and 3, the necessary physics and experimental techniques for their investigation are outlined. Chapters 4 to 6 present measurements of cyclotron resonance in layered materials. Chapter 4 describes several models for the origin of cyclotron resonance harmonics, and describes the first definite measurement of the harmonics of a cyclotron resonance in an organic molecular metal, namely beta sup - (BEDT-TTF) sub 2 SF sub 5 CH sub 2 CF sub 2 SO sub 3. The angle dependence of the field p...

  8. Comparison of field emissivities with laboratory measurements and ASTER data

    Science.gov (United States)

    Mira, M.; Schmugge, T.; Valor, E.; Caselles, V.; Coll, C.

    2008-10-01

    Surface emissivity in the thermal infrared (TIR) region is an important parameter for determining the land surface temperature from remote sensing measurements. This work compares the emissivities measured by different field methods (the Box method and the Temperature and Emissivity Separation, TES, algorithm) as well as emissivity data from ASTER scenes and the spectra obtained from the ASTER Spectral Library. The study was performed with a field radiometer having TIR bands with central wavelengths at 11.3 μm, 10.6 μm, 9.1 μm, 8.7 μm and 8.4 μm, similar to the ASTER TIR bands. The measurements were made at two sites in southern New Mexico. The first was in the White Sands National Monument, and the second was an open shrub land in the Jornada Experimental Range, in the northern Chihuahuan Desert, New Mexico, USA. The measurements show that, in general, emissivities derived with the Box method agree within 3% with those derived with the TES method for the spectral bands centered at 10.6 μm and 11.3 μm. However, the emissivities for the shorter wavelength bands are higher when derived with the Box method than those with the TES algorithm (differences range from 2% to 7%). The field emissivities agree within 2% with the laboratory spectrum for the 8-13 μm, 11.3 μm and 10.6 μm bands. However, the field and laboratory measurements in general differ from 3% to 16% for the shorter wavelength bands, i.e., 9.1 μm, 8.6 μm and 8.4 μm. A good agreement between the experimental measurements and the ASTER TIR emissivity data is observed for White Sands, especially over the 9 - 12 μm range (agreement within 4%). The study showed an emissivity increase up to 17% in the 8 to 9 μm range and an increase of 8% in emissivity ratio of average channels (8.4 μm, 8.6 μm, 9.1 μm):(10.6 μm, 11.3 μm) for two gypsum samples with different water content.

  9. Can the analyte-triggered asymmetric autocatalytic Soai reaction serve as a universal analytical tool for measuring enantiopurity and assigning absolute configuration?

    Science.gov (United States)

    Welch, Christopher J; Zawatzky, Kerstin; Makarov, Alexey A; Fujiwara, Satoshi; Matsumoto, Arimasa; Soai, Kenso

    2016-12-20

    An investigation is reported on the use of the autocatalytic enantioselective Soai reaction, known to be influenced by the presence of a wide variety of chiral materials, as a generic tool for measuring the enantiopurity and absolute configuration of any substance. Good generality for the reaction across a small group of test analytes was observed, consistent with literature reports suggesting a diversity of compound types that can influence the stereochemical outcome of this reaction. Some trends in the absolute sense of stereochemical enrichment were noted, suggesting the possible utility of the approach for assigning absolute configuration to unknown compounds, by analogy to closely related species with known outcomes. Considerable variation was observed in the triggering strength of different enantiopure materials, an undesirable characteristic when dealing with mixtures containing minor impurities with strong triggering strength in the presence of major components with weak triggering strength. A strong tendency of the reaction toward an 'all or none' type of behavior makes the reaction most sensitive for detecting enantioenrichment close to zero. Consequently, the ability to discern modest from excellent enantioselectivity was relatively poor. While these properties limit the ability to obtain precise enantiopurity measurements in a simple single addition experiment, prospects may exist for more complex experimental setups that may potentially offer improved performance.

  10. International Accounting Convergence in the Field of Fair Value Measurement

    Directory of Open Access Journals (Sweden)

    Diana Cozma Ighian

    2015-09-01

    Full Text Available The investors’ desire for high-quality, internationally comparable financial information that is useful for decision-making in increasingly global capital markets imposed an international convergence, the ultimate goal of which is a single set of international accounting standards that companies worldwide would use for both domestic and cross-border financial reporting. The guidance, set out in IFRS 13 Fair Value Measurement and the update to Topic 820 (formerly referred to as SFAS 157, completes a major project of the boards’ joint work to improve IFRSs and US GAAP and to bring about their convergence. This article describes the controversial history of fair value measurement and the main novelties in the field of fair value measurement, arising from the international convergence process.

  11. Sound field separation with sound pressure and particle velocity measurements

    DEFF Research Database (Denmark)

    Fernandez Grande, Efren; Jacobsen, Finn; Leclère, Quentin

    2012-01-01

    separation techniques make it possible to distinguish between outgoing and incoming waves from the two sides, and thus NAH can be applied. In this paper, a separation method based on the measurement of the particle velocity in two layers and another method based on the measurement of the pressure...... and the velocity in a single layer are proposed. The two methods use an equivalent source formulation with separate transfer matrices for the outgoing and incoming waves, so that the sound from the two sides of the array can be modeled independently. A weighting scheme is proposed to account for the distance...... pressure-velocity method, although it requires an additional measurement surface. On the whole, the separation methods can be useful when the disturbance of the incoming field is significant. Otherwise the direct reconstruction is more accurate and straightforward. © 2012 Acoustical Society of America....

  12. Measurements of insolation variation over a solar collector field

    Energy Technology Data Exchange (ETDEWEB)

    1978-12-30

    The experiment described in this report makes observations to determine the direct insolation every 16 sec at corners of a quadrilateral approximately 600 meters in size located near Barstow, California. This size approximates the collector field of the solar power plant to be built near Barstow. Data from the first three months of operation of this experiment indicate cloudy conditions, capable of affecting the operation of a solar power plant, occurred during 15% of the daylight hours of some months. Patterns of insolation variation over the experiment area indicate shadows often exist with dimensions less than the projected size of the collection field for the 10 MW/sub e/ solar thermal power plant. Detailed statistical summaries of four partly cloudy events are included. Rates of insolation change on an individual sensor greater than or equal to 30 Wm/sup -2/ sec/sup -1/ have been observed, but these rate measurements have probably been limited by the response time of the experimental system. Spatial averaging of the measured insolation over the sensor field lowers the rate of insolation change.

  13. Electromagnetic field analysis and RFEC signal modeling for gap measurement between liquid injection nozzle and nuclear fuel channel

    Energy Technology Data Exchange (ETDEWEB)

    Lee, Dong Hoon; Jung, Hyun Kyu; Cheong, Yong Moo; Huh, Young; Lee, Yoon Sang [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

    2004-05-15

    Fuel channels including pressure tube(Pt) and calandria tube(CT) are important components of pressurized heavy water reactor(PHWR). A sagging of fuel channel increases by heat and radiation exposure with the increasing operation time. The contact of fuel channel to liquid injection nozzle(LIN) is thus a critical issue in power plant safety. In order to solve this safety issue, the electromagnetic technique was applied to compliment the present inspection technology. Electromagnetic fields were investigated for the gap measurement between CT and LIN using FEM computer modeling. We calculated the electromagnetic fields, such as, magnetic flux density, current density near the fuel channel and checked the adaptability of RFEC technology. The RFEC Signals using the volume integral method(VIM) were simulated for obtaining the optimal inspection parameters, including frequency, inter-coil spacing, coil size and configuration. Finally, we development the remote field eddy current sensor that can CT/LIN gap measurement efficiently.

  14. Solar Cluster: multipoint magnetic field and plasma parameter measurements in the solar wind

    Science.gov (United States)

    Vieira, L. E.; Echer, E.; dal Lago, A.; Schuch, N. J.

    allows just one line of view as the structure pass throughout the spacecraft. In order to improve our knowledge of solar wind structure and its dynamics it is necessary to measure the spatial structure of the interplanetary magnetic field and plasma parameters. We will discuss the scientific questions and objectives of the mission, possible target regions in space and the payload instrumentation and measurement requirements. The determination of the number of spacecraft, their configuration and the costs of this mission will not be discussed here.

  15. REVIEW OF HIGH FIELD Q SLOPE, CAVITY MEASUREMENTS

    Energy Technology Data Exchange (ETDEWEB)

    Gianluigi Ciovati

    2008-01-23

    One of the most interesting phenomenon occurring in superconducting radio-frequency (SRF) cavities made of bulk niobium is represented by a sharp decrease of the quality factor above peak surface magnetic field of about 90 mT and is referred to as "high field Q-slope" or "Q-drop". This phenomenon was observed first in 1997 and since then some effort was devoted to the understanding of the causes behind it. Still, no clear physical interpretation of the Q-drop has emerged, despite several attempts. In this contribution, I will review the experimental results for various cavities measured in many laboratories and I will try to identify common features and differences related to the Q-drop.

  16. Measurement of Electromagnetic Fields Emitted from Some Medical Devices

    Directory of Open Access Journals (Sweden)

    Shaker Faisel

    2013-04-01

    Full Text Available     New medical devices such as surgery devices, physiotherapy devices, cosmetological devices and Magnetic Resonance Imaging (MRI systems generate a complex electromagnetic fields, so they consider as a potential   hazard for medical personnel during surgical procedures. The aim of this research is to detect the EMFs emitted from medical devices and determine the safety ranges from these devices which emit EMF radiations in order to protect Medical staff from its risks. The research has been performed in two parts, numerical calculation and practical measurement. Practical measurements are done in Dijlah hospital at Tikrit city. Obtaining results shows that the practical measurements are consistent with the mathematical calculation results. Comparison of these results with the safety standard guideline limits shows that they   are within the acceptable exposure limits recommended by the International Commission on Non-Ionizing Radiation Protection (ICNIRP and that means there is no health risk from exposure to these fields if the exposure is for a short and not continued periods and lay within the acceptable limits.    

  17. Personal radiofrequency electromagnetic field exposure measurements in Swiss adolescents.

    Science.gov (United States)

    Roser, Katharina; Schoeni, Anna; Struchen, Benjamin; Zahner, Marco; Eeftens, Marloes; Fröhlich, Jürg; Röösli, Martin

    2017-02-01

    Adolescents belong to the heaviest users of wireless communication devices, but little is known about their personal exposure to radiofrequency electromagnetic fields (RF-EMF). The aim of this paper is to describe personal RF-EMF exposure of Swiss adolescents and evaluate exposure relevant factors. Furthermore, personal measurements were used to estimate average contributions of various sources to the total absorbed RF-EMF dose of the brain and the whole body. Personal exposure was measured using a portable RF-EMF measurement device (ExpoM-RF) measuring 13 frequency bands ranging from 470 to 3600MHz. The participants carried the device for three consecutive days and kept a time-activity diary. In total, 90 adolescents aged 13 to 17years participated in the study conducted between May 2013 and April 2014. In addition, personal measurement values were combined with dose calculations for the use of wireless communication devices to quantify the contribution of various RF-EMF sources to the daily RF-EMF dose of adolescents. Main contributors to the total personal RF-EMF measurements of 63.2μW/m(2) (0.15V/m) were exposures from mobile phones (67.2%) and from mobile phone base stations (19.8%). WLAN at school and at home had little impact on the personal measurements (WLAN accounted for 3.5% of total personal measurements). According to the dose calculations, exposure from environmental sources (broadcast transmitters, mobile phone base stations, cordless phone base stations, WLAN access points, and mobile phones in the surroundings) contributed on average 6.0% to the brain dose and 9.0% to the whole-body dose. RF-EMF exposure of adolescents is dominated by their own mobile phone use. Environmental sources such as mobile phone base stations play a minor role. Copyright © 2016 Elsevier Ltd. All rights reserved.

  18. Optical Field Measurement of Nano-Apertures with a Scanning Near-Field Optical Microscope

    Institute of Scientific and Technical Information of China (English)

    XU Tie-Jun; XU Ji-Ying; WANG Jia; TIAN Qian

    2004-01-01

    @@ We investigate optical near-field distributions of the unconventional C-apertures and the conventional square apertures in preliminary experiment with an aperture scanning near-field optical microscope. These nano-apertures are fabricated in Au film on a glass substrate with focused ion beam technology. The experimental results indicate the uptrend of output light intensity that a C-aperture enables the intensity maximum to increase at least 10times more than a square aperture with same unit length. The measured near-field light spot sizes of C-apertureand square aperture with 200-nm unit length are 439nm × 500nm and 245nm × 216nm, respectively.

  19. Measuring the complex field scattered by single submicron particles

    Directory of Open Access Journals (Sweden)

    Marco A. C. Potenza

    2015-11-01

    Full Text Available We describe a method for simultaneous measurements of the real and imaginary parts of the field scattered by single nanoparticles illuminated by a laser beam, exploiting a self-reference interferometric scheme relying on the fundamentals of the Optical Theorem. Results obtained with calibrated spheres of different materials are compared to the expected values obtained through a simplified analytical model without any free parameters, and the method is applied to a highly polydisperse water suspension of Poly(D,L-lactide-co-glycolide nanoparticles. Advantages with respect to existing methods and possible applications are discussed.

  20. Spectral reflectance measurement methodologies for TUZ Golu field campaign

    CSIR Research Space (South Africa)

    Boucher, Y

    2011-07-01

    Full Text Available MEASUREMENT METHODOLOGIES FOR TUZ GOLU FIELD CAMPAIGN Y. Bouchera, F. Viallefonta, A. Deadmanb, N. Foxb , I. Behnertb, D. Griffithc, P. Harrisb, D. Helderd, E. Knaepse, L. Leighd, Y. Lif, H. Ozeng, F. Ponzonih, S. Sterckxe a Onera - The French Aerospace... A uncertainty [4]. Thus, the variation of the reflectance between the different points is a combination of the variation at small scale and at the scale of the sampling grid, typically between 20 m and 40 m. This strategy has been chosen by Onera...