Photoemission and photo-field-emission from photocathodes with arrays of silicon tips under continuous and pulsed lasers action; Photoemission et photoemission de champ a partir de photocathodes a reseaux de pointes de silicium sous l`action de lasers continus et pulses

Energy Technology Data Exchange (ETDEWEB)

Laguna, M.

1995-11-01

The electron machines`s development and improvement go through the discovery of new electron sources of high brightness. After reminding the interests in studying silicon cathodes with array of tips as electron sources, I describe, in the three steps model, the main phenomenological features related to photoemission and photoemission and photo-field-emission from a semi-conductor. the experimental set-ups used for the measurements reported in chapter four, five and six are described in chapter three. In chapter three. In chapter four several aspects of photo-field-emission in continuous and nanosecond regimes, studied on the Clermont-Ferrand`s test bench are tackled. We have measured quantum efficacies of 0.4 percent in the red (1.96 eV). Temporal responses in the nanoseconds range (10 ns) were observed with the Nd: YLF laser. With the laser impinging at an oblique angle we obtained ratios of photocurrent to dark current of the order of twenty. The issue of the high energy extracted photocurrent saturation is addressed and I give a preliminary explanation. In collaboration with the L.A.L. (Laboratoire de l`Accelerateur Lineaire) some tests with shortened pulsed laser beam (Nd: YAG laser 35 ps) were performed. Satisfactory response times have been obtained within the limitation of the scope (400 ps). (authors). 101 refs. 93 figs., 27 tabs., 3 photos., 1 append.

Relaxation and cross section effects in valence band photoemission spectroscopy

International Nuclear Information System (INIS)

McFeely, F.R.

1976-09-01

Various problems relating to the interpretation of valence band x-ray photoemission (XPS) spectra of solids are discussed. The experiments and calculations reported herein deal with the following questions: (1) To what extent do many-body effects manifest themselves in an XPS valence band spectrum, and thus invalidate a direct comparison between the photoemission energy distribution, I(E), and the density of states, N(E), calculated on the basis of ground-state one-electron theory. (2) The effect of the binding-energy-dependent photoemission cross section on I(E) at XPS energies. (3) In favorable cases indicated by (1) and (2) we examine the effect of the interaction of the crystal field with the apparent spin-orbit splittings of core levels observed in XPS spectra. (4) The use of tight binding band structure calculations to parameterize the electronic band structure from XPS and other data is described. (5) The use of high energy angle-resolved photoemission on oriented single crystals to gain orbital symmetry information is discussed. (6) The evolution of the shape of the photoemission energy distribution (of polycrystalline Cu) as a function of photon energy from 50 less than or equal h ω less than or equal 175 is discussed

Attosecond-controlled photoemission from metal nanowire tips in the few-electron regime

KAUST Repository

Ahn, B.

2017-02-07

Metal nanotip photoemitters have proven to be versatile in fundamental nanoplasmonics research and applications, including, e.g., the generation of ultrafast electron pulses, the adiabatic focusing of plasmons, and as light-triggered electron sources for microscopy. Here, we report the generation of high energy photoelectrons (up to 160 eV) in photoemission from single-crystalline nanowire tips in few-cycle, 750-nm laser fields at peak intensities of (2-7.3) × 1012 W/cm2. Recording the carrier-envelope phase (CEP)-dependent photoemission from the nanowire tips allows us to identify rescattering contributions and also permits us to determine the high-energy cutoff of the electron spectra as a function of laser intensity. So far these types of experiments from metal nanotips have been limited to an emission regime with less than one electron per pulse. We detect up to 13 e/shot and given the limited detection efficiency, we expect up to a few ten times more electrons being emitted from the nanowire. Within the investigated intensity range, we find linear scaling of cutoff energies. The nonlinear scaling of electron count rates is consistent with tunneling photoemission occurring in the absence of significant charge interaction. The high electron energy gain is attributed to field-induced rescattering in the enhanced nanolocalized fields at the wires apex, where a strong CEP-modulation is indicative of the attosecond control of photoemission.

Experiments recently carried out on the photoemission station at Beijing Synchrotron Radiation Facility

International Nuclear Information System (INIS)

Kurash Ibrahim; Wu Ziyu; Qian Haijie; Zhang Jing; Abbas, M.I.; Chen Zhigang; Su Run; Liu Fengqin

2003-01-01

With a sustained and steady operation of the photoemission station at Beijing Synchrotron Radiation Facility, users from different research fields have carried out their investigation on the electronic structure of metal surface-interface, metal doped fullerene as well as colossal magneto-resistance materials utilizing different experimental modes provided by the photoemission station. In this paper authors would present some representative experimental results obtained on the station

Fermi liquid character in the photoemission/inverse photoemission spectra of highly correlated electron systems

International Nuclear Information System (INIS)

Riseborough, P.S.

1990-01-01

We calculate the photoemission/inverse photoemission spectrum for an N-fold degenerate Hubbard model, in the 1/N approximation. The spectra are broadened, and for sufficiently large Coulomb interaction strengths the spectra show satellites both in the photoemission and the brehmstrahlung isochromat spectroscopy portions of the spectra. The intensity of the spectra at the fermi level are equal to the noninteracting values, in accordance with Luttinger's theorem. We show that this can result in a temperature-dependent peak at the Fermi level; the width of the peak is governed by the quasi-particle lifetime. We relate the temperature dependent peak to the Fermi-liquid properties

Inverse photoemission of uranium oxides

International Nuclear Information System (INIS)

Roussel, P.; Morrall, P.; Tull, S.J.

2009-01-01

Understanding the itinerant-localised bonding role of the 5f electrons in the light actinides will afford an insight into their unusual physical and chemical properties. In recent years, the combination of core and valance band electron spectroscopies with theoretic modelling have already made significant progress in this area. However, information of the unoccupied density of states is still scarce. When compared to the forward photoemission techniques, measurements of the unoccupied states suffer from significantly less sensitivity and lower resolution. In this paper, we report on our experimental apparatus, which is designed to measure the inverse photoemission spectra of the light actinides. Inverse photoemission spectra of UO 2 and UO 2.2 along with the corresponding core and valance electron spectra are presented in this paper. UO 2 has been reported previously, although through its inclusion here it allows us to compare and contrast results from our experimental apparatus to the previous Bremsstrahlung Isochromat Spectroscopy and Inverse Photoemission Spectroscopy investigations

Photoemission and photo-field-emission from photocathodes with arrays of silicon tips under continuous and pulsed lasers action

International Nuclear Information System (INIS)

Laguna, M.

1995-11-01

The electron machines's development and improvement go through the discovery of new electron sources of high brightness. After reminding the interests in studying silicon cathodes with array of tips as electron sources, I describe, in the three steps model, the main phenomenological features related to photoemission and photoemission and photo-field-emission from a semi-conductor. the experimental set-ups used for the measurements reported in chapter four, five and six are described in chapter three. In chapter three. In chapter four several aspects of photo-field-emission in continuous and nanosecond regimes, studied on the Clermont-Ferrand's test bench are tackled. We have measured quantum efficacies of 0.4 percent in the red (1.96 eV). Temporal responses in the nanoseconds range (10 ns) were observed with the Nd: YLF laser. With the laser impinging at an oblique angle we obtained ratios of photocurrent to dark current of the order of twenty. The issue of the high energy extracted photocurrent saturation is addressed and I give a preliminary explanation. In collaboration with the L.A.L. (Laboratoire de l'Accelerateur Lineaire) some tests with shortened pulsed laser beam (Nd: YAG laser 35 ps) were performed. Satisfactory response times have been obtained within the limitation of the scope (400 ps). (authors). 101 refs. 93 figs., 27 tabs., 3 photos., 1 append

Organic [6,6]-phenyl-C61-butyric-acid-methyl-ester field effect transistors: Analysis of the contact properties by combined photoemission spectroscopy and electrical measurements

Science.gov (United States)

Scheinert, S.; Grobosch, M.; Sprogies, J.; Hörselmann, I.; Knupfer, M.; Paasch, G.

2013-05-01

Carrier injection barriers determined by photoemission spectroscopy for organic/metal interfaces are widely accepted to determine the performance of organic field-effect transistors (OFET), which strongly depends on this interface at the source/drain contacts. This assumption is checked here in detail, and a more sophisticated connection is presented. According to the preparation process described in our recently published article [S. Scheinert, J. Appl. Phys. 111, 064502 (2012)], we prepared PCBM/Au and PCBM/Al samples to characterize the interface by photoemission and electrical measurements of PCBM based OFETs with bottom and top (TOC) contacts, respectively. The larger drain currents for TOC OFETs indicate the presence of Schottky contacts at source/drain for both metals. The hole injection barrier as determined by photoemission is 1.8 eV for both Al and Au. Therefore, the electron injection barriers are also the same. In contrast, the drain currents are orders of magnitude larger for the transistors with the Al contacts than for those with the Au contacts. We show that indeed the injection is determined by two other properties measured also by photoemission, the (reduced) work functions, and the interface dipoles, which have different sign for each contact material. In addition, we demonstrate by core-level and valence band photoemission that the deposition of gold as top contact onto PCBM results in the growth of small gold clusters. With increasing gold coverage, the clusters grow inside and begin to form a metallic, but not uniform, closed film onto PCBM.

Photoemission electron microscopy of localized surface plasmons in silver nanostructures at telecommunication wavelengths

Energy Technology Data Exchange (ETDEWEB)

Mårsell, Erik; Larsen, Esben W.; Arnold, Cord L.; Xu, Hongxing; Mauritsson, Johan; Mikkelsen, Anders, E-mail: anders.mikkelsen@sljus.lu.se [Department of Physics, Lund University, P.O. Box 118, 22 100 Lund (Sweden)

2015-02-28

We image the field enhancement at Ag nanostructures using femtosecond laser pulses with a center wavelength of 1.55 μm. Imaging is based on non-linear photoemission observed in a photoemission electron microscope (PEEM). The images are directly compared to ultra violet PEEM and scanning electron microscopy (SEM) imaging of the same structures. Further, we have carried out atomic scale scanning tunneling microscopy on the same type of Ag nanostructures and on the Au substrate. Measuring the photoelectron spectrum from individual Ag particles shows a larger contribution from higher order photoemission processes above the work function threshold than would be predicted by a fully perturbative model, consistent with recent results using shorter wavelengths. Investigating a wide selection of both Ag nanoparticles and nanowires, field enhancement is observed from 30% of the Ag nanoparticles and from none of the nanowires. No laser-induced damage is observed of the nanostructures neither during the PEEM experiments nor in subsequent SEM analysis. By direct comparison of SEM and PEEM images of the same nanostructures, we can conclude that the field enhancement is independent of the average nanostructure size and shape. Instead, we propose that the variations in observed field enhancement could originate from the wedge interface between the substrate and particles electrically connected to the substrate.

Practical Photoemission Characterization Of Molecular Films And Related Interfaces

International Nuclear Information System (INIS)

Ivanco, J.

2013-01-01

Even though the term ‘organic electronics’ evokes rather organic devices, a significant part of its scope deals with physical properties of ‘active elements’ such as organic films and interfaces. Examination of the film growth and the evolution of the interface formation are particularly needful for the understanding a mechanism controlling their final properties. Performing such experiments in an ultra-high vacuum allows both to ‘stretch’ the time scale for pseudo real-time observations and to control properties of the probed systems on the atomic level. Photoemission technique probes directly electronic and chemical structure and it has thereby established among major tools employed in the field.This review primarily focuses to electronic properties of oligomeric molecular films and their interfaces examined by photoemission. Yet, it does not aspire after a complete overview on the topic; it rather aims to otherwise standard issues encountered at the photoemission characterization and analysis of the organic materials, though requiring to consider particularities of molecular films in terms of the growth, electronic properties, and their characterization and analysis. In particular, the fundamental electronic parameters of molecular films such as the work function, the ionization energy, and the interfacial energy level alignment, and their interplay, will be pursued with considering often neglected influence of the molecular orientation. Further, the implication on the band bending in molecular films based on photoemission characterization, and a model on the driving mechanism for the interfacial energy level alignment will be addressed. (author)

Simple theoretical analysis of the photoemission from quantum confined effective mass superlattices of optoelectronic materials

Directory of Open Access Journals (Sweden)

Debashis De

2011-07-01

Full Text Available The photoemission from quantum wires and dots of effective mass superlattices of optoelectronic materials was investigated on the basis of newly formulated electron energy spectra, in the presence of external light waves, which controls the transport properties of ultra-small electronic devices under intense radiation. The effect of magnetic quantization on the photoemission from the aforementioned superlattices, together with quantum well superlattices under magnetic quantization, has also been investigated in this regard. It appears, taking HgTe/Hg1−xCdxTe and InxGa1−xAs/InP effective mass superlattices, that the photoemission from these quantized structures is enhanced with increasing photon energy in quantized steps and shows oscillatory dependences with the increasing carrier concentration. In addition, the photoemission decreases with increasing light intensity and wavelength as well as with increasing thickness exhibiting oscillatory spikes. The strong dependence of the photoemission on the light intensity reflects the direct signature of light waves on the carrier energy spectra. The content of this paper finds six different applications in the fields of low dimensional systems in general.

Photoemission studies of mixed valent systems

International Nuclear Information System (INIS)

Parks, R.D.; Raaen, S.; denBoer, M.L.; Williams, G.P.

1984-01-01

Photoemission spectroscopy has been used to study a number of aspects of the mixed valent state (corresponding to non-integral 4f occupation) in rare earth systems. Deep core photoemission (e.g., from 3d or 4d levels) allows the measurement of the 4f occupancy and surface valence shifts, and, as well, the indirect measurement of the effect of solid state environment on the energy of hybridization between 4f electrons and conduction electrons. 4f-Derived photoemission has been used to study surface valance and chemical shifts and to infer the nature of the mixed valent ground state. A combination of 4f-derived photoemission and add-electron spectroscopy provides a measurement of the rf Coulomb correlation energy, an important parameter in the mixed valent problem. A review of these approaches will be presented, with emphasis on Ce-based systems, whose behavior falls outside the usual description of 4f-unstable systems

Zen and the art of dichroic photoemission

Energy Technology Data Exchange (ETDEWEB)

Laan, Gerrit van der, E-mail: gerrit.vanderlaan@diamond.ac.uk

2015-04-15

Highlights: • General theory for angle and spin dependence of dichroic core-level photoemission. • Fundamental spectra give correlation between spin and orbital moments. • Interference term between emission channels results in MLDAD and CDAD. • Core-hole polarization is probed by resonant photoemission. - Abstract: The discovery of magnetic dichroism in photoemission is celebrating its 25th anniversary this year. Here a review of the underlying general theory for the angular and spin dependence of dichroic core-level photoemission is presented using both a single-particle model and a many-body approach. The established methods of angular momentum coupling offer an elegant and powerful way to analyse the magnetic dichroism and spin polarization in photoemission from core and localized valence levels. In the presence of core-valence interactions one can distinguish different fundamental spectra, which via sum rules are related to physical properties described by coupled tensor operators for spin and orbital moments. By separating the angular dependence from the physical information, different geometries can be distinguished to measure the magnetic circular dichroism (MCD), linear dichroism (LD), circular dichroism in the angular dependence (CDAD), and magnetic linear dichroism in the angular dependence (MLDAD). Various ways to probe the core-hole polarization are discussed, such as using the angular dependence, moment analysis of the spectral distribution, and resonant photoemission decay.

Photoemission spectroscopy using synchrotron radiation

International Nuclear Information System (INIS)

Kobayashi, K.L.I.

1980-01-01

It is an epoch making event for photoemission spectroscopy that the light sources of continuous wavelength from vacuum ultra-violet to X-ray region have become available by the advent of synchrotron radiation. Specifically the progress after stable intense light has become obtainable from storage rings is very significant. One of the features of these synchrotron radiation is its extreme polarization of radiating pattern. Though the elementary processes of photoemission out of solids are the basic themes, phenomenalistic 3-stage model is usually applied to the analysis of experiments. In this model, the process of photoemission is considered by dividing into three stages, namely the generation of photoelectrons due to optical transition between electron status -- the transportation of photoelectrons to solid surfaces -- breaking away from the surfaces. The spectrometers, the energy analyzers of photoelectrons, and sample-preparing room used for photoemission spectroscopy are described. Next, energy distribution curves are explained. At the end, photoelectron yield spectroscopy, CFS (constant final energy spectroscopy) and CIS (constant initial energy spectroscopy), Auger yield and interatomic Auger yield, the determination of surface structure by normal emission CIS, and surface EXAFS (extended X-ray absorption fine structure) are described. As seen above, the application specifically to surface physics is promising in the future. (Wakatsuki, Y.)

Photoemission in nanosecond and picosecond regimes obtained from macro and micro cathodes

International Nuclear Information System (INIS)

Boussoukaya, M.; Bergeret, H.; Chehab, R.; Leblond, B.; Franco, M.

1987-03-01

For Lasertron studies at LAL, results obtained from tests on different photocathodes are given below. Using respectively two Nd: YAG lasers (a nanosecond one and a picosecond one) we have determined the level and the intensity of pulsed photoemission and the photoelectric yield in UV, green and infrared lights. We obtained a total current of more than 1 A with nanosecond width from a single W needle, and photoconversion yield of more than 1 was reached in green and UV lights. In classical pulsed photoemission, obtained photoconversion yield from LaB 6 photocathode was of about 10 -3 in higher fields

General survey of recent development of photoemission spectroscopy

International Nuclear Information System (INIS)

Edamoto, Kazuyuki

1994-01-01

On the present state of the recent development of photoemission spectroscopy, by limiting the topics to the development of the spectroscopy proper and the development contributing to the progress of surface science, general explanation is made. As to the development that enabled to heighten spectrum resolution, surface core-level shift and the precise measurement of the Fermi surface of surface level are described, showing the example. Also a number of the developments which enabled the utilization of the light source, of which the wavelength is variable, and which was brought about by synchrotron radiation beam, were mentioned. Besides, spin polarized photoelectron spectroscopy, the development of photoelectron microscope and others are outlined. Photoemission spectroscopy is very useful for analyzing the electron condition of solid surfaces. There are two factors in heightening core level spectrum resolution, namely, heightening the resolution of an electron energy analyzer proper and the utilization of synchrotron radiation as a light source. High resolution core-level spectra, angle-resolved photoemission spectroscopy, and as the light source of which the wavelength is variable, resonance photoemission spectroscopy, constant initial state spectroscopy and soft X-ray photoemission spectroscopy, and as the recently developed spectroscopy, spin polarized photoemission spectroscopy, Auger photoelectron coincidence spectroscopy and photoelectron microscope are explained. (K.I.)

Energy-resolved attosecond interferometric photoemission from Ag(111) and Au(111) surfaces

Science.gov (United States)

Ambrosio, M. J.; Thumm, U.

2018-04-01

Photoelectron emission from solid surfaces induced by attosecond pulse trains into the electric field of delayed phase-coherent infrared (IR) pulses allows the surface-specific observation of energy-resolved electronic phase accumulations and photoemission delays. We quantum-mechanically modeled interferometric photoemission spectra from the (111) surfaces of Au and Ag, including background contributions from secondary electrons and direct emission by the IR pulse, and adjusted parameters of our model to energy-resolved photoelectron spectra recently measured at a synchrotron light source by Roth et al. [J. Electron Spectrosc. 224, 84 (2018), 10.1016/j.elspec.2017.05.008]. Our calculated spectra and photoelectron phase shifts are in fair agreement with the experimental data of Locher et al. [Optica 2, 405 (2015), 10.1364/OPTICA.2.000405]. Our model's not reproducing the measured energy-dependent oscillations of the Ag(111) photoemission phases may be interpreted as evidence for subtle band-structure effects on the final-state photoelectron-surface interaction not accounted for in our simulation.

Coherent and incoherent processes in resonant photoemission

Energy Technology Data Exchange (ETDEWEB)

Magnuson, M.; Karis, O.; Weinelt, M. [Uppsala Univ. (Sweden)] [and others

1997-04-01

In this contribution the authors present the distinction between coherent and incoherent processes in resonant photoemission. As a first step they determine whether an autoionization process is photoemission-like or Auger-like. The discussion is based on measurements for a weakly bonded adsorption system, Ar/Pt(111). This type of system is well adapted to investigate these effects since it yields distinctly shifted spectral features depending on the nature of the process. After this, the question of resonance photoemission in metallic systems is addressed. This is done in connection with measurements at the 2p edges for Ni metal. Ni has been one of the prototype systems for resonant photoemission. The resonances have been discussed in connection with the strong correlation and d-band localization effects in this system. Based on the results some general comments about the appearance of resonant effects in metallic systems are made.

Gauge invariance in the theoretical description of time-resolved angle-resolved pump/probe photoemission spectroscopy

Energy Technology Data Exchange (ETDEWEB)

Freericks, J. K.; Krishnamurthy, H. R.; Sentef, M. A.; Devereaux, T. P.

2015-10-01

Nonequilibrium calculations in the presence of an electric field are usually performed in a gauge, and need to be transformed to reveal the gauge-invariant observables. In this work, we discuss the issue of gauge invariance in the context of time-resolved angle-resolved pump/probe photoemission. If the probe is applied while the pump is still on, one must ensure that the calculations of the observed photocurrent are gauge invariant. We also discuss the requirement of the photoemission signal to be positive and the relationship of this constraint to gauge invariance. We end by discussing some technical details related to the perturbative derivation of the photoemission spectra, which involve processes where the pump pulse photoexcites electrons due to nonequilibrium effects.

Hard X-ray photoemission spectroscopy

International Nuclear Information System (INIS)

Kobayashi, Keisuke

2009-01-01

Except in the very early stage of the development of X-ray photoemission spectroscopy (XPS) by Kai Siegbahn and his coworkers, the excitation sources for XPS studies have predominantly been the Al Kα and Mg Kα emission lines. The advent of synchrotron radiation sources opened up the possibility of tuning the excitation photon energy with much higher throughputs for photoemission spectroscopy, however the excitation energy range was limited to the vacuum ultra violet and soft X-ray regions. Over the past 5-6 years, bulk-sensitive hard X-ray photoemission spectroscopy using high-brilliance high-flux X-rays from third generation synchrotron radiation facilities has been developed. This article reviews the history of HXPES covering the period from Kai Siegbahn and his coworkers' pioneering works to the present, and describes the fundamental aspects, instrumentation, applications to solid state physics, applied physics, materials science, and industrial applications of HXPES. Finally, several challenging new developments which have been conducted at SPring-8 by collaborations among several groups are introduced.

Correlation, temperature and disorder: Recent developments in the one-step description of angle-resolved photoemission

Science.gov (United States)

Braun, Jürgen; Minár, Ján; Ebert, Hubert

2018-04-01

Various apparative developments extended the potential of angle-resolved photoemission spectroscopy tremendously during the last two decades. Modern experimental arrangements consisting of new photon sources, analyzers and detectors supply not only extremely high angle and energy resolution but also spin resolution. This provides an adequate platform to study in detail new materials like low-dimensional magnetic structures, Rashba systems, topological insulator materials or high TC superconductors. The interest in such systems has grown enormously not only because of their technological relevance but even more because of exciting new physics. Furthermore, the use of photon energies from few eV up to several keV makes this experimental technique a rather unique tool to investigate the electronic properties of solids and surfaces. The following article reviews the corresponding recent theoretical developments in the field of angle-resolved photoemission with a special emphasis on correlation effects, temperature and relativistic aspects. The most successful theoretical approach to deal with angle-resolved photoemission is the so-called spectral function or one-step formulation of the photoemission process. Nowadays, the one-step model allows for photocurrent calculations for photon energies ranging from a few eV to more than 10 keV, to deal with arbitrarily ordered and disordered systems, to account for finite temperatures, and considering in addition strong correlation effects within the dynamical mean-field theory or similar advanced approaches.

Photoemission of Single Dust Grains for Heliospheric Conditions

Science.gov (United States)

Spann, James F., Jr.; Venturini, Catherine C.; Abbas, Mian M.; Comfort, Richard H.

2000-01-01

Initial results of an experiment to measure the photoemission of single dust grains as a function of far ultraviolet wavelengths are presented. Coulombic forces dominate the interaction of the dust grains in the heliosphere. Knowledge of the charge state of dust grains, whether in a dusty plasma (Debye length grains is primarily determined by primary electron and ion collisions, secondary electron emission and photoemission due to ultraviolet sunlight. We have established a unique experimental technique to measure the photoemission of individual micron-sized dust grains in vacuum. This technique resolves difficulties associated with statistical measurements of dust grain ensembles and non-static dust beams. The photoemission yield of Aluminum Oxide 3-micron grains For wavelengths from 120-300 nm with a spectral resolution of 1 nm FWHM is reported. Results are compared to interplanetary conditions.

Instrument developments for inverse photoemission

International Nuclear Information System (INIS)

Brenac, A.

1987-02-01

Experimental developments principally concerning electron sources for inverse photoemission are presented. The specifications of the electron beam are derived from experiment requirements, taking into account the limitations encountered (space charge divergence). For a wave vector resolution of 0.2 A -1 , the maximum current is 25 microA at 20 eV. The design of a gun providing such a beam in the range 5 to 50 eV is presented. Angle-resolved inverse photoemission experiments show angular effects at 30 eV. For an energy of 10 eV, angular effects should be stronger, but the low efficiency of the spectrometer in this range makes the experiments difficult. The total energy resolution of 0.3 eV is the result mainly of electron energy spread, as expected. The electron sources are based on field effect electron emission from a cathode consisting of a large number of microtips. The emission arises from a few atomic cells for each tip. The ultimate theoretical energy spread is 0.1 eV. This value is not attained because of an interface resistance problem. A partial solution of this problem allows measurement of an energy spread of 0.9 eV for a current of 100 microA emitted at 60 eV. These cathodes have a further advantage in that emission can occur at a low temperature [fr

Theoretical estimates of spherical and chromatic aberration in photoemission electron microscopy

Energy Technology Data Exchange (ETDEWEB)

Fitzgerald, J.P.S., E-mail: fit@pdx.edu; Word, R.C.; Könenkamp, R.

2016-01-15

We present theoretical estimates of the mean coefficients of spherical and chromatic aberration for low energy photoemission electron microscopy (PEEM). Using simple analytic models, we find that the aberration coefficients depend primarily on the difference between the photon energy and the photoemission threshold, as expected. However, the shape of the photoelectron spectral distribution impacts the coefficients by up to 30%. These estimates should allow more precise correction of aberration in PEEM in experimental situations where the aberration coefficients and precise electron energy distribution cannot be readily measured. - Highlights: • Spherical and chromatic aberration coefficients of the accelerating field in PEEM. • Compact, analytic expressions for coefficients depending on two emission parameters. • Effect of an aperture stop on the distribution is also considered.

Electronic Structure of the Kitaev Material α-RuCl3 Probed by Photoemission and Inverse Photoemission Spectroscopies

OpenAIRE

Soobin Sinn; Choong Hyun Kim; Beom Hyun Kim; Kyung Dong Lee; Choong Jae Won; Ji Seop Oh; Moonsup Han; Young Jun Chang; Namjung Hur; Hitoshi Sato; Byeong-Gyu Park; Changyoung Kim; Hyeong-Do Kim; Tae Won Noh

2016-01-01

Recently, $\\alpha$-$\\textrm{RuCl}_3$ has attracted much attention as a possible material realization of the honeycomb Kitaev model, which may stabilize a quantum-spin-liquid state. Compared to extensive studies on its magnetic properties, there is still a lack of understanding on its electronic structure, which is strongly related with its Kitaev physics. Here, the electronic structure of $\\alpha$-$\\textrm{RuCl}_3$ is investigated by photoemission (PE) and inverse photoemission (IPE) spectros...

Rotatable spin-polarized electron source for inverse-photoemission experiments

International Nuclear Information System (INIS)

Stolwijk, S. D.; Wortelen, H.; Schmidt, A. B.; Donath, M.

2014-01-01

We present a ROtatable Spin-polarized Electron source (ROSE) for the use in spin- and angle-resolved inverse-photoemission (SR-IPE) experiments. A key feature of the ROSE is a variable direction of the transversal electron beam polarization. As a result, the inverse-photoemission experiment becomes sensitive to two orthogonal in-plane polarization directions, and, for nonnormal electron incidence, to the out-of-plane polarization component. We characterize the ROSE and test its performance on the basis of SR-IPE experiments. Measurements on magnetized Ni films on W(110) serve as a reference to demonstrate the variable spin sensitivity. Moreover, investigations of the unoccupied spin-dependent surface electronic structure of Tl/Si(111) highlight the capability to analyze complex phenomena like spin rotations in momentum space. Essentially, the ROSE opens the way to further studies on complex spin-dependent effects in the field of surface magnetism and spin-orbit interaction at surfaces

Photoemission starting of induction rf-driven multicusp ion sources

International Nuclear Information System (INIS)

Pickard, D.S.; Leung, K.N.; Perkins, L.T.; Ponce, D.M.; Young, A.T.

1996-01-01

It has been demonstrated that pulsed and continuous wave, rf-driven hydrogen discharges can be started with photoemission. The extracted H - current from a photoemission-started plasma has been investigated and does not differ significantly from that of a filament-started plasma. The minimum pressure for photoemissive starting was found to be higher than that of filament starting, 17 mTorr compared to 7 mTorr, respectively, in this particular configuration. copyright 1996 American Institute of Physics

Attosecond-controlled photoemission from metal nanowire tips in the few-electron regime

KAUST Repository

Ahn, B.; Schö tz, J.; Kang, M.; Okell, W. A.; Mitra, S.; Fö rg, B.; Zherebtsov, S.; Sü ß mann, F.; Burger, C.; Kü bel, M.; Liu, C.; Wirth, A.; Di Fabrizio, Enzo M.; Yanagisawa, H.; Kim, D.; Kim, B.; Kling, M. F.

2017-01-01

sources for microscopy. Here, we report the generation of high energy photoelectrons (up to 160 eV) in photoemission from single-crystalline nanowire tips in few-cycle, 750-nm laser fields at peak intensities of (2-7.3) × 1012 W/cm2. Recording the carrier

Photoemission measurements for low energy x-ray detector applications

International Nuclear Information System (INIS)

Day, R.H.

1981-01-01

Photoemission has been studied for nearly 100 years as both a means of investigating quantum physics, and as a practical technique for transducing optical/x-ray photons into electrical currents. Numerous x-ray detection schemes, such as streak cameras and x-ray sensitive diodes, exploit this process because of its simplicity, adaptability, and speed. Recent emphasis on diagnostics for low temperature, high density, and short-lived, plasmas for inertial confinement fusion has stimulated interest in x-ray photoemission in the sub-kilovolt regime. In this paper, a review of x-ray photoemission measurements in the 50 eV to 10 keV x-ray region is given and the experimental techniques are reviewed. A semiempirical model of x-ray photoemission is discussed and compared to experimental measurements. Finally, examples of absolutely calibrated instruments are shown

Theory of photoemission and inverse-photoemission spectra of highly correlated electron systems: A weak-coupling 1/N expansion

International Nuclear Information System (INIS)

Riseborough, P.S.

1989-01-01

An N-fold-degenerate Hubbard model is examined in the weak-coupling regime. The one-electron Green's function is calculated from a systematic expansion of the irreducible self-energy in powers of 1/N. To lowest order in the expansion, one obtains a trivial mean-field theory. In the next leading order in 1/N, one finds that the dynamics are dominated by bosonlike collective excitations. The resulting expansion has the characteristics of the standard weak-coupling field theory, except the inclusion of the 1/N factors extends the regime of applicability to include Stoner-like enhancement factors which can be N times larger. The joint valence-band photoemission and inverse-photoemission spectrum is given by the trace of the imaginary part of the one-electron Green's function. The electronic spectrum has been calculated by truncating the series expansion for the self-energy in the lowest nontrivial order of 1/N. For small values of the Coulomb interaction between the electrons, the spectrum reduces to the form obtained by calculating the self-energy to second order in the Coulomb interaction. The spectra shows a narrowing of the band in the vicinity of the Fermi level and long high-energy band tails. When the boson spectrum softens, indicating the vicinity of a phase transition, the electronic spectrum shows the appearance of satellites. The results are compared with experimental observations of anomalies in the electronic spectra of uranium-based systems. The relation between the electronic spectrum and the thermodynamic mass enhancements is also discussed

Timing analysis of two-electron photoemission

International Nuclear Information System (INIS)

Kheifets, A S; Ivanov, I A; Bray, Igor

2011-01-01

We predict a significant delay of two-electron photoemission from the helium atom after absorption of an attosecond XUV pulse. We establish this delay by solving the time-dependent Schroedinger equation and by subsequently tracing the field-free evolution of the two-electron wave packet. This delay can also be related to the energy derivative of the phase of the complex double-photoionization (DPI) amplitude which we evaluate by using the convergent close-coupling method. Our observations indicate that future attosecond time delay measurements on DPI of He can provide information on the absolute quantum phase and elucidate various mechanisms of this strongly correlated ionization process. (fast track communication)

A New Spin on Photoemission Spectroscopy

Energy Technology Data Exchange (ETDEWEB)

Jozwiak, Chris [Univ. of California, Berkeley, CA (United States)

2008-12-01

The electronic spin degree of freedom is of general fundamental importance to all matter. Understanding its complex roles and behavior in the solid state, particularly in highly correlated and magnetic materials, has grown increasingly desirable as technology demands advanced devices and materials based on ever stricter comprehension and control of the electron spin. However, direct and efficient spin dependent probes of electronic structure are currently lacking. Angle Resolved Photoemission Spectroscopy (ARPES) has become one of the most successful experimental tools for elucidating solid state electronic structures, bolstered by-continual breakthroughs in efficient instrumentation. In contrast, spin-resolved photoemission spectroscopy has lagged behind due to a lack of similar instrumental advances. The power of photoemission spectroscopy and the pertinence of electronic spin in the current research climate combine to make breakthroughs in Spin and Angle Resolved Photoemission Spectroscopy (SARPES) a high priority . This thesis details the development of a unique instrument for efficient SARPES and represents a radical departure from conventional methods. A custom designed spin polarimeter based on low energy exchange scattering is developed, with projected efficiency gains of two orders of magnitude over current state-of-the-art polarimeters. For energy analysis, the popular hemispherical analyzer is eschewed for a custom Time-of-Flight (TOF) analyzer offering an additional order of magnitude gain in efficiency. The combined instrument signifies the breakthrough needed to perform the high resolution SARPES experiments necessary for untangling the complex spin-dependent electronic structures central to today's condensed matter physics.

Soft X-ray angle-resolved photoemission spectroscopy of heavily boron-doped superconducting diamond films

Directory of Open Access Journals (Sweden)

T. Yokoya, T. Nakamura, T. Matushita, T. Muro, H. Okazaki, M. Arita, K. Shimada, H. Namatame, M. Taniguchi, Y. Takano, M. Nagao, T. Takenouchi, H. Kawarada and T. Oguchi

2006-01-01

Full Text Available We have performed soft X-ray angle-resolved photoemission spectroscopy (SXARPES of microwave plasma-assisted chemical vapor deposition diamond films with different B concentrations in order to study the origin of the metallic behavior of superconducting diamond. SXARPES results clearly show valence band dispersions with a bandwidth of ~23 eV and with a top of the valence band at gamma point in the Brillouin zone, which are consistent with the calculated valence band dispersions of pure diamond. Boron concentration-dependent band dispersions near the Fermi level (EF exhibit a systematic shift of EF, indicating depopulation of electrons due to hole doping. These SXARPES results indicate that diamond bands retain for heavy boron doping and holes in the diamond band are responsible for the metallic states leading to superconductivity at low temperature. A high-resolution photoemission spectroscopy spectrum near EF of a heavily boron-doped diamond superconductor is also presented.

Photoemission electronic states of epitaxially grown magnetite films

International Nuclear Information System (INIS)

Zalecki, R.; Kolodziejczyk, A.; Korecki, J.; Spiridis, N.; Zajac, M.; Kozlowski, A.; Kakol, Z.; Antolak, D.

2007-01-01

The valence band photoemission spectra of epitaxially grown 300 A single crystalline magnetite films were measured by the angle-resolved ultraviolet photoemission spectroscopy (ARUPS) at 300 K. The samples were grown either on MgO(0 0 1) (B termination) or on (0 0 1) Fe (iron-rich A termination), thus intentionally presenting different surface stoichiometry, i.e. also different surface electronic states. Four main features of the electron photoemission at about -1.0, -3.0, -5.5 and -10.0 eV below a chemical potential show systematic differences for two terminations; this difference depends on the electron outgoing angle. Our studies confirm sensitivity of angle resolved PES technique on subtleties of surface states

Large Band Gap of alpha-RuCl3 Probed by Photoemission and Inverse Photoemission Spectroscopy

Science.gov (United States)

Sinn, Soobin; Kim, Choong Hyun; Sandilands, Luke; Lee, Kyungdong; Won, Choongjae; Oh, Ji Seop; Han, Moonsup; Chang, Young Jun; Hur, Namjung; Sato, Hitoshi; Park, Byeong-Gyu; Kim, Changyoung; Kim, Hyeong-Do; Noh, Tae Won

The Kitaev honeycomb lattice model has attracted great attention because of its possibility to stabilize a quantum spin liquid ground state. Recently, it was proposed that alpha-RuCl3 is its material realization and the first 4 d relativistic Mott insulator from an optical spectrum and LDA + U + SO calculations. Here, we present photoemission and inverse photoemission spectra of alpha-RuCl3. The observed band gap is about 1.8 eV, which suggests that the previously assigned optical gap of 0.3 eV is misinterpreted, and that the strong peak at about 1.2 eV in the optical spectrum may be associated with an actual optical gap. Assuming a strong excitonic effect of 0.6 eV in the optical spectrum, all the structures except for the peak at 0.3 eV are consistent with our electronic spectra. When compared with LDA + U + SO calculations, the value of U should be considerably larger than the previous one, which implies that the spin-orbit coupling is not a necessary ingredient for the insulating mechanism of alpha-RuCl3. We also present angle-resolved photoemission spectra to be compared with LDA + U + SO and LDA +DMFT calculations.

Fourier Transform Photoemission Spectroscopy

NARCIS (Netherlands)

Meinders, M.B.J.; Drabe, K.E.; Jonkman, H.T.; Sawatzky, G.A.

1996-01-01

It is shown that photoemission spectra can be obtained by exciting the electrons with two phase-correlated wave trains. The phase-correlated wave trains are obtained by sending broad-band ultra-violet light, coming from a deuterium lamp, through a Michelson interferometer. It is possible to

Fourier transform photoemission spectroscopy

NARCIS (Netherlands)

Meinders, M.B J; Drabe, K.E.; Jonkman, H.T.; Sawatzky, G.A

It is shown that photoemission spectra can be obtained by exciting the electrons with two phase-correlated wave trains. The phase-correlated wave trains are obtained by sending broad-band ultra-violet light, coming from a deuterium lamp, through a Michelson interferometer. It is possible to

Realisation of a ultra-high vacuum system and technique development of microscopical emitters preparation in silicium. First measurements of field emission current and field photoemission

International Nuclear Information System (INIS)

El Manouni, A.

1990-12-01

The development of research in the domain of photocathode (electron sources) illuminated by laser light to produce intense multiple bunches of electrons in short time is needed by many applications as linear collider e + e - , free electron laser, lasertron, etc... In this way, after a study of field emission, of photoemission and of photofield emission, we prepared microscopical emitters in silicium heavy and weakly doped a boron using a technique of microlithography. Then, we realized a system of ultra-high vacuum of studying property of emission from photocathodes realized. The experiment results obtained in field emission and photofield emission have shown that a behaviour unexpected for P-silicium tips array compared to P + -silicon tips array. With P-type silicon, a quantum yield of 21 percent has been measured for laser power of 140 mW and for applied field of 1.125 x 10 7 V/m and an instantaneous response to laser light beam has been observed. It has been noted that presence of oxyde at the surface of photocathode limits extensively the emission current. The fluctuations of emission current are due to quality of vacuum [fr

Spectroscopic imaging, diffraction, and holography with x-ray photoemission

Energy Technology Data Exchange (ETDEWEB)

1992-02-01

X-ray probes are capable of determining the spatial structure of an atom in a specific chemical state, over length scales from about a micron all the way down to atomic resolution. Examples of these probes include photoemission microscopy, energy-dependent photoemission diffraction, photoelectron holography, and X-ray absorption microspectroscopy. Although the method of image formation, chemical-state sensitivity, and length scales can be very different, these X-ray techniques share a common goal of combining a capability for structure determination with chemical-state specificity. This workshop will address recent advances in holographic, diffraction, and direct imaging techniques using X-ray photoemission on both theoretical and experimental fronts. A particular emphasis will be on novel structure determinations with atomic resolution using photoelectrons.

Spectroscopic imaging, diffraction, and holography with x-ray photoemission

International Nuclear Information System (INIS)

1992-02-01

X-ray probes are capable of determining the spatial structure of an atom in a specific chemical state, over length scales from about a micron all the way down to atomic resolution. Examples of these probes include photoemission microscopy, energy-dependent photoemission diffraction, photoelectron holography, and X-ray absorption microspectroscopy. Although the method of image formation, chemical-state sensitivity, and length scales can be very different, these X-ray techniques share a common goal of combining a capability for structure determination with chemical-state specificity. This workshop will address recent advances in holographic, diffraction, and direct imaging techniques using X-ray photoemission on both theoretical and experimental fronts. A particular emphasis will be on novel structure determinations with atomic resolution using photoelectrons

Simultaneous measurements of photoemission and morphology of various Al alloys during mechanical deformation

Science.gov (United States)

Cai, M.; Li, W.; Dickinson, J. T.

2006-11-01

We report simultaneous measurements of strain and photoelectron emission from high purity Al (1350), Al-Mg (5052), Al-Mn (3003), Al-Cu (2024), and Al-Mg-Si (6061) alloys under uniaxial tension due to pulsed excimer laser radiation (248nm). The emission of low-energy photoelectrons is sensitive to deformation-induced changes in surface morphology, including the formation of slip lines and slip bands. Alloy composition and surface treatment significantly influence the photoemission during deformation. Surface oxide enhances the signal-to-noise level during photoemission measurement. In the early stage of deformation (strain ⩽0.04), photoemission intensity increases gradually in a nonlinear fashion. While subsequent photoemission increases almost linearly with strain until failure in samples with thin oxide layer (˜31Å), there are two linear segments of photoemission for the samples with oxide of 45Å. The onset of strain localization corresponds to the intersection point of two linear segments, usually at a strain of 0.08-0.20. A constitutive model incorporating microstructure evolution and work hardening during tensile deformation is proposed to qualitatively interpret the growth of the photoemission as a function of strain. Photoemissions from various alloys are interpreted in the light of surface treatment, work function, composition, and microstructural development during deformation.

Induced photoemission from driven nonadiabatic dynamics in an avoided crossing system

Energy Technology Data Exchange (ETDEWEB)

Arasaki, Yasuki; Mizuno, Yuta; Takatsuka, Kazuo, E-mail: kaztak@mns2.c.u-tokyo.ac.jp [Department of Basic Science, Graduate School of Arts and Sciences, The University of Tokyo, Komaba, 153-8902 Tokyo (Japan); Scheit, Simona [Department of Basic Science, Graduate School of Arts and Sciences, The University of Tokyo, Komaba, 153-8902 Tokyo (Japan); Theoretische Chemie, Universität Heidelberg, Im Neuneheimer Feld 229, 69120 Heidelberg (Germany)

2014-12-21

When vibrational dynamics on an ionic state (large dipole moment) is coupled to that on a neutral state (small dipole moment) such as at an avoided crossing in the alkali halide system, the population transfer between the states cause oscillation of the molecular dipole, leading to dipole emission. Such dynamics may be driven by an external field. We study how the coupled wavepacket dynamics is affected by the parameters (intensity, frequency) of the driving field with the aim of making use of the photoemission as an alternative detection scheme of femtosecond and subfemtosecond vibrational and electronic dynamics or as a characteristic optical source.

Photoemission from solids: the transition from solid-state to atomic physics

International Nuclear Information System (INIS)

Shirley, D.A.

1980-08-01

As the photon energy is increased, photoemission from solids undergoes a slow transition from solid-state to atomic behavior. However, throughout the energy range hν = 10 to 1000 eV or higher both types of phenomena are present. Thus angle-resolved photoemission can only be understood quantitatively if each experimenter recognizes the presence of band-structure, photoelectron diffraction, and photoelectron asymmetry effects. The quest for this understanding will build some interesting bridges between solid-state and atomic physics and should also yield important new insights about the phenomena associated with photoemission

Hard X-ray photoemission spectroscopy of transition-metal oxide thin films and interfaces

International Nuclear Information System (INIS)

Wadati, H.; Fujimori, A.

2013-01-01

Highlights: •Photoemission spectroscopy is a powerful technique to study the electronic structures of transition-metal oxides. •Hard X-ray photoemission spectroscopy (HXPES) is a new type of photoemission spectroscopy which can probe bulk states. •HXPES is very suitable for studying oxide thin films such as the composition dependence and the film thickness dependence. -- Abstract: Photoemission spectroscopy is a powerful experimental technique to study the electronic structures of solids, especially of transition-metal oxides. Recently, hard X-ray photoemission spectroscopy (HXPES) has emerged as a more relevant experimental technique to obtain clear information about bulk states. Here, we describe how HXPES can be conveniently applied to study the interesting subjects on oxide thin films such as the composition dependence and the film thickness dependence of the electronic structures and the interfacial electronic structure of multilayers

Angle-resolved photoemission spectroscopy of liquid water at 29.5 eV.

Science.gov (United States)

Nishitani, Junichi; West, Christopher W; Suzuki, Toshinori

2017-07-01

Angle-resolved photoemission spectroscopy of liquid water was performed using extreme ultraviolet radiation at 29.5 eV and a time-of-flight photoelectron spectrometer. SiC/Mg coated mirrors were employed to select the single-order 19th harmonic from laser high harmonics, which provided a constant photon flux for different laser polarizations. The instrument was tested by measuring photoemission anisotropy for rare gases and water molecules and applied to a microjet of an aqueous NaI solution. The solute concentration was adjusted to eliminate an electric field gradient around the microjet. The observed photoelectron spectra were analyzed considering contributions from liquid water, water vapor, and an isotropic background. The anisotropy parameters of the valence bands (1 b 1 , 3 a 1 , and 1 b 2 ) of liquid water are considerably smaller than those of gaseous water, which is primarily attributed to electron scattering in liquid water.

Iron 1s X-ray photoemission of Fe{sub 2}O{sub 3}

Energy Technology Data Exchange (ETDEWEB)

Miedema, P.S., E-mail: p.s.miedema@gmail.com [Inorganic Chemistry and Catalysis, Debye Institute for Nanomaterials Science, Utrecht University, Universiteitsweg 99, 3584 CG Utrecht (Netherlands); Borgatti, F. [CNR-ISMN, Instituto per Io Studio di Materiali Nanostrutturati, Via Gobetti 101, I-40129 Bologna (Italy); Offi, F. [Dipartimento di Scienze, Università di Roma Tre, I-00146 Rome (Italy); Panaccione, G. [Consiglio Nazionale delle Ricerche, CNR-IOM, Laboratorio TASC, Area Science Park, I-34149 Trieste (Italy); Groot, F.M.F. de [Inorganic Chemistry and Catalysis, Debye Institute for Nanomaterials Science, Utrecht University, Universiteitsweg 99, 3584 CG Utrecht (Netherlands)

2015-08-15

Highlights: • Three peaks of 1s XPS of Fe{sub 2}O{sub 3} means use of three configurations. • 1s XPS vs 2p XPS: advantage of 1s XPS for charge transfer parameter analysis. • Charge transfer multiplet analysis with same parameters for 1s and 2p XPS. - Abstract: We present the 1s X-ray photoemission spectrum of α-Fe{sub 2}O{sub 3} in comparison with its 2p photoemission spectrum. We show that in case of transition metal oxides, because the 1s core hole is not affected by core hole spin-orbit coupling and almost not affected by core-valence multiplet effects, the Fe 1s spectrum and the complementary charge transfer multiplet calculations allow for an accurate determination of the charge transfer parameters. The consistency of the obtained parameters for the 1s photoemission was confirmed with 2p photoemission calculations and compared to 2p experimental photoemission spectra.

Angle-resolved photoemission study of NiO and CoO

International Nuclear Information System (INIS)

Shen, Z.X.; Lindberg, P.A.P.; Shih, C.K.; Spicer, W.E.; Lindau, I.

1989-01-01

The authors report an angle-resolved photoemission investigation of the electronic structures of NiO and CoO. The lattice effects on the photoemission spectra of these highly correlated materials are important. The magnitudes of dispersions of the oxygen bands agree with band calculations, but the experimental data of the localized 3d bands do not agree with the band calculations

SUM-RULES FOR MAGNETIC DICHROISM IN RARE-EARTH 4F-PHOTOEMISSION

NARCIS (Netherlands)

THOLE, BT; VANDERLAAN, G

1993-01-01

We present new sum rules for magnetic dichroism in spin polarized photoemission from partly filled shells which give the expectation values of the orbital and spin magnetic moments and their correlations in the ground state. We apply this to the 4f photoemission of rare earths, where the

Giant Cu 2p Resonances in CuO Valence-Band Photoemission

NARCIS (Netherlands)

Tjeng, L.H.; Chen, C.T.; Ghijsen, J.; Rudolf, P.; Sette, F.

1991-01-01

We report the observation of a giant resonance in the Cu 2p resonant-photoemission spectra of CuO. The study allows the unambiguous identification of the local Cu 3d8 configuration in the valence-band photoemission spectrum, providing conclusive evidence for the charge-transfer nature of the

Three-dimensional characterization of extreme ultraviolet mask blank defects by interference contrast photoemission electron microscopy.

Science.gov (United States)

Lin, Jingquan; Weber, Nils; Escher, Matthias; Maul, Jochen; Han, Hak-Seung; Merkel, Michael; Wurm, Stefan; Schönhense, Gerd; Kleineberg, Ulf

2008-09-29

A photoemission electron microscope based on a new contrast mechanism "interference contrast" is applied to characterize extreme ultraviolet lithography mask blank defects. Inspection results show that positioning of interference destructive condition (node of standing wave field) on surface of multilayer in the local region of a phase defect is necessary to obtain best visibility of the defect on mask blank. A comparative experiment reveals superiority of the interference contrast photoemission electron microscope (Extreme UV illumination) over a topographic contrast one (UV illumination with Hg discharge lamp) in detecting extreme ultraviolet mask blank phase defects. A depth-resolved detection of a mask blank defect, either by measuring anti-node peak shift in the EUV-PEEM image under varying inspection wavelength condition or by counting interference fringes with a fixed illumination wavelength, is discussed.

Quantification of plasmon excitations in core-level photoemission

International Nuclear Information System (INIS)

Yubero, F.; Tougaard, S.

2005-01-01

Calculation of photoelectron spectra (PES) based on our previous dielectric response model [A. C. Simonsen et al. Phys. Rev. B 56, 1612 (1997)] for electronic excitations in PES are compared with recently reported experimental data. It is found that the dielectric description of electron energy losses in photoemission reproduces quantitatively the angular dependence of the surface and bulk electron losses observed experimentally for the Al2s photoemission spectra of Al(111), excited with MgKα radiation. The model also allows to calculate the separate intrinsic and extrinsic effects in photoemission. Thus, the extrinsic losses account for more than 95% of the total surface excitations. Regarding the bulk excitations, both extrinsic and intrinsic contributions vary significantly with emission angle. The intrinsic contribution represents ∼35% of the intensity at the bulk plasmon position at normal emission while only 18% at 80 deg. glancing emission. The calculations presented here can easily be used to interpret PES spectra of other materials in terms of intrinsic and extrinsic effects, if their dielectric properties are known

Photoemission using femtosecond laser pulses

International Nuclear Information System (INIS)

Srinivasan-Rao, T.; Tsang, T.; Fischer, J.

1991-10-01

Successful operation of short wavelength FEL requires an electron bunch of current >100 A and normalized emittance < 1 mm-mrad. Recent experiments show that RF guns with photocathodes as the electron source may be the ideal candidate for achieving these parameters. To reduce the emittance growth due to space charge and RF dynamics effects, the gun may have to operate at high field gradient (hence at high RF frequency) and a spot size small compared to the aperture. This may necessitate the laser pulse duration to be in the subpicosecond regime to reduce the energy spread. We will present the behavior of metal photocathodes upon irradiation with femtosecond laser beams, comparison of linear and nonlinear photoemission, and scalability to high currents. Theoretical estimate of the intrinsic emittance at the photocathode in the presence of the anomalous heating of the electrons, and the tolerance on the surface roughness of the cathode material will be discussed

Evidence of the nature of core-level photoemission satellites using angle-resolved photoemission extended fine structure

International Nuclear Information System (INIS)

Moler, E.J.; Kellar, S.A.; Huff, W.R.A.

1997-01-01

The authors present a unique method of experimentally determining the angular momentum and intrinsic/extrinsic origin of core-level photoemission satellites by examining the satellite diffraction pattern in the Angle Resolved Photoemission Extended Fine Structure (ARPEFS) mode. They show for the first time that satellite peaks not associated with chemically differentiated atomic species display an ARPEFS intensity oscillation. They present ARPEFS data for the carbon 1s from (√3x√3)R30 CO/Cu(111) and p2mg(2xl)CO/Ni(110), nitrogen 1s from c(2x2) N 2 /Ni(100), cobalt 1s from p(1x1)Co/Cu(100), and nickel 3p from clean nickel (111). The satellite peaks and tails of the Doniach-Sunjic line shapes in all cases exhibit ARPEFS curves which indicate an angular momentum identical to the main peak and are of an intrinsic nature

Angle-resolved photoemission extended fine structure

International Nuclear Information System (INIS)

Barton, J.J.

1985-03-01

Measurements of the Angle-Resolved Photoemission Extended Fine Structure (ARPEFS) from the S(1s) core level of a c(2 x 2)S/Ni(001) are analyzed to determine the spacing between the S overlayer and the first and second Ni layers. ARPEFS is a type of photoelectron diffraction measurement in which the photoelectron kinetic energy is swept typically from 100 to 600 eV. By using this wide range of intermediate energies we add high precision and theoretical simplification to the advantages of the photoelectron diffraction technique for determining surface structures. We report developments in the theory of photoelectron scattering in the intermediate energy range, measurement of the experimental photoemission spectra, their reduction to ARPEFS, and the surface structure determination from the ARPEFS by combined Fourier and multiple-scattering analyses. 202 refs., 67 figs., 2 tabs

Quantitative analysis of valence photoemission spectra and quasiparticle excitations at chromophore-semiconductor interfaces.

Science.gov (United States)

Patrick, Christopher E; Giustino, Feliciano

2012-09-14

Investigating quasiparticle excitations of molecules on surfaces through photoemission spectroscopy forms a major part of nanotechnology research. Resolving spectral features at these interfaces requires a comprehensive theory of electron removal and addition processes in molecules and solids which captures the complex interplay of image charges, thermal effects, and configurational disorder. Here, we develop such a theory and calculate the quasiparticle energy-level alignment and the valence photoemission spectrum for the prototype biomimetic solar cell interface between anatase TiO(2) and the N3 chromophore. By directly matching our calculated photoemission spectrum to experimental data, we clarify the atomistic origin of the chromophore peak at low binding energy. This case study sets a new standard in the interpretation of photoemission spectroscopy at complex chromophore-semiconductor interfaces.

Angle-resolved photoemission spectroscopy of liquid water at 29.5 eV

Directory of Open Access Journals (Sweden)

Junichi Nishitani

2017-07-01

Full Text Available Angle-resolved photoemission spectroscopy of liquid water was performed using extreme ultraviolet radiation at 29.5 eV and a time-of-flight photoelectron spectrometer. SiC/Mg coated mirrors were employed to select the single-order 19th harmonic from laser high harmonics, which provided a constant photon flux for different laser polarizations. The instrument was tested by measuring photoemission anisotropy for rare gases and water molecules and applied to a microjet of an aqueous NaI solution. The solute concentration was adjusted to eliminate an electric field gradient around the microjet. The observed photoelectron spectra were analyzed considering contributions from liquid water, water vapor, and an isotropic background. The anisotropy parameters of the valence bands (1b1, 3a1, and 1b2 of liquid water are considerably smaller than those of gaseous water, which is primarily attributed to electron scattering in liquid water.

Angle-resolved photoemission extended fine structure: Multiple layers of emitters and multiple initial states

International Nuclear Information System (INIS)

Huff, W.R.A.; Kellar, S.A.; Moler, E.J.; California Univ., Berkeley, CA; Chen, Y.; Wu, H.; Shirley, D.A.; Hussain, Z.

1995-01-01

Recently, angle-resolved photoemission extended fine structure (ARPEFS) has been applied to experimental systems involving multiple layers of emitters and non-s core-level photoemission in an effort to broaden the utility of the technique. Most of the previous systems have been comprised of atomic or molecular overlayers adsorbed onto a single-crystal, metal surface and the photoemission data were taken from an s atomic core-level in the overlayer. For such a system, the acquired ARPEFS data is dominated by the p o final state wave backscattering from the substrate atoms and is well understood. In this study, we investigate ARPEFS as a surface-region structure determination technique when applied to experimental systems comprised of multiple layers of photoemitters and arbitrary initial state core-level photoemission. Understanding the data acquired from multiple layers of photoemitters is useful for studying multilayer interfaces, ''buried'' surfaces, and clean crystals in ultra- high vacuum. The ability to apply ARPEFS to arbitrary initial state core-level photoemission obviously opens up many systems to analysis. Efforts have been ongoing to understand such data in depth. We present clean Cu(111) 3s, 3p, and 3d core-level, normal photoemission data taken on a high resolution soft x-ray beamline 9.3.2 at the Advanced Light Source in Berkeley, California and clean Ni(111) 3p normal photoemission data taken at the National Synchrotron Light Source in Upton, New York, USA

Iron 1s X-ray photoemission of Fe2O3

NARCIS (Netherlands)

Miedema, P. S.; Borgatti, F.; Offi, F.; Panaccione, G.; de Groot, F. M. F.

We present the Is X-ray photoemission spectrum of alpha-Fe2O3 in comparison with its 2p photoemission spectrum. We show that in case of transition metal oxides, because the 1s core hole is not affected by core hole spin-orbit coupling and almost not affected by core-valence multiplet effects, the Fe

Evidence of the nature of core-level photoemission satellites using angle-resolved photoemission extended fine structure

Energy Technology Data Exchange (ETDEWEB)

Moler, E.J.; Kellar, S.A.; Huff, W.R.A. [Lawrence Berkeley National Lab., CA (United States)] [and others

1997-04-01

The authors present a unique method of experimentally determining the angular momentum and intrinsic/extrinsic origin of core-level photoemission satellites by examining the satellite diffraction pattern in the Angle Resolved Photoemission Extended Fine Structure (ARPEFS) mode. They show for the first time that satellite peaks not associated with chemically differentiated atomic species display an ARPEFS intensity oscillation. They present ARPEFS data for the carbon 1s from ({radical}3x{radical}3)R30 CO/Cu(111) and p2mg(2xl)CO/Ni(110), nitrogen 1s from c(2x2) N{sub 2}/Ni(100), cobalt 1s from p(1x1)Co/Cu(100), and nickel 3p from clean nickel (111). The satellite peaks and tails of the Doniach-Sunjic line shapes in all cases exhibit ARPEFS curves which indicate an angular momentum identical to the main peak and are of an intrinsic nature.

Direct angle resolved photoemission spectroscopy and ...

Indian Academy of Sciences (India)

Since 1997 we systematically perform direct angle resolved photoemission spectroscopy (ARPES) on in-situ grown thin (< 30 nm) cuprate films. Specifically, we probe low-energy electronic structure and properties of high-c superconductors (HTSC) under different degrees of epitaxial (compressive vs. tensile) strain.

Bulk sensitive hard x-ray photoemission electron microscopy

Energy Technology Data Exchange (ETDEWEB)

Patt, M., E-mail: m.patt@fz-juelich.de; Wiemann, C. [Peter Grünberg Institute (PGI-6) and JARA-FIT, Research Center Jülich, D-52425 Jülich (Germany); Weber, N.; Escher, M.; Merkel, M. [Focus GmbH, Neukirchner Str. 2, D-65510 Hünstetten (Germany); Gloskovskii, A.; Drube, W. [DESY Photon Science, Deutsches Elektronen-Synchrotron, D-22603 Hamburg (Germany); Schneider, C. M. [Peter Grünberg Institute (PGI-6) and JARA-FIT, Research Center Jülich, D-52425 Jülich (Germany); Fakultät f. Physik and Center for Nanointegration Duisburg-Essen (CeNIDE), Universität Duisburg-Essen, D-47048 Duisburg (Germany)

2014-11-15

Hard x-ray photoelectron spectroscopy (HAXPES) has now matured into a well-established technique as a bulk sensitive probe of the electronic structure due to the larger escape depth of the highly energetic electrons. In order to enable HAXPES studies with high lateral resolution, we have set up a dedicated energy-filtered hard x-ray photoemission electron microscope (HAXPEEM) working with electron kinetic energies up to 10 keV. It is based on the NanoESCA design and also preserves the performance of the instrument in the low and medium energy range. In this way, spectromicroscopy can be performed from threshold to hard x-ray photoemission. The high potential of the HAXPEEM approach for the investigation of buried layers and structures has been shown already on a layered and structured SrTiO{sub 3} sample. Here, we present results of experiments with test structures to elaborate the imaging and spectroscopic performance of the instrument and show the capabilities of the method to image bulk properties. Additionally, we introduce a method to determine the effective attenuation length of photoelectrons in a direct photoemission experiment.

Theory of tunneling and photoemission spectroscopy for high-temperature superconductors

International Nuclear Information System (INIS)

Kouznetsov, K.; Coffey, L.

1996-01-01

A comprehensive analysis is presented of the tunneling conductance and angle-resolved photoemission spectra in high-temperature superconductors. It is shown that unexplained features of the tunneling and photoemission spectra such as broad backgrounds, dips, and asymmetry of the tunneling conductance can arise in a model of spin-fluctuation mediated inelastic tunneling. Effects of directionality in tunneling play an important role in determining the behavior of the tunneling conductance. copyright 1996 The American Physical Society

Surface-plasmon enhanced photoemission of a silver nano-patterned photocathode

Science.gov (United States)

Zhang, Z.; Li, R.; To, H.; Andonian, G.; Pirez, E.; Meade, D.; Maxson, J.; Musumeci, P.

2017-09-01

Nano-patterned photocathodes (NPC) take advantage of plasmonic effects to resonantly increase absorption of light and localize electromagnetic field intensity on metal surfaces leading to surface-plasmon enhanced photoemission. In this paper, we report the status of NPC research at UCLA including in particular the optimization of the dimensions of a nanohole array on a silver wafer to enhance plasmonic response at 800 nm light, the development of a spectrally-resolved reflectivity measurement setup for quick nanopattern validation, and of a novel cathode plug to enable high power tests of NPCs on single crystal substrates in a high gradient radiofrequency gun.

Einstein's photoemission emission from heavily-doped quantized structures

CERN Document Server

Ghatak, Kamakhya Prasad

2015-01-01

This monograph solely investigates the Einstein's Photoemission(EP) from Heavily Doped(HD) Quantized Structures on the basis of newly formulated electron dispersion laws. The materials considered are quantized structures of HD non-linear optical, III-V, II-VI, Ge, Te, Platinum Antimonide, stressed materials, GaP, Gallium Antimonide, II-V, Bismuth Telluride together with various types of HD superlattices and their Quantized counterparts respectively. The EP in HD opto-electronic materials and their nanostructures is studied in the presence of strong light waves and intense electric fields  that control the studies of such quantum effect devices. The suggestions for the experimental determinations of different important physical quantities in HD 2D and 3D materials  and the importance of measurement of band gap in HD optoelectronic materials under intense built-in electric field in nano devices and strong external photo excitation (for measuring   physical properties in the presence of intense light waves w...

Extraction of the Electric Field in Field Plate Assisted RESURF Devices

NARCIS (Netherlands)

Boksteen, B.K.; Dhar, S.; Heringa, A.; Koops, G.E.J.; Hueting, Raymond Josephus Engelbart

2012-01-01

It has previously been reported that the lateral electric field (Ex) in the drain extension of thin SOI HV (700V) field plate assisted RESURF devices can be extracted from their ID-VD characteristics in the subthreshold regime. In this work the prerequisites for valid field extraction and the

Synchrotron photoemission study of (Zn,Co)O films with uniform Co distribution

DEFF Research Database (Denmark)

Guziewicz, E.; Lukasiewicz, M. I.; Wachnicki, L.

2011-01-01

of foreign phases and metal accumulations as indicated by TEM data. The electronic structure of (Zn,Co)O films was studied by Resonant Photoemission Spectroscopy across the Co3p–Co3d photoionization threshold. We have observed that the resonant enhancement of the photoemission intensity from the Co3d shell...

Femtosecond time-resolved two-photon photoemission study of organic semiconductor copper phthalocyanine film

International Nuclear Information System (INIS)

Tanaka, A.; Tohoku University; University of Rochester, NY; Yan, L.; Watkins, N.J.; Gao, Y.

2004-01-01

Full text: Organic semiconductors are recently attracting much interest from the viewpoints of both device and fundamental physics. These organic semiconductors are considered to be important constituents of the future devices, such as organic light-emitting diode, organic field effect transistor, and organic solid-state injection laser. In order to elucidate their detailed physical properties and to develop the future devices, it is indispensable to understand their excited-state dynamics as well as their electronic structures. The femtosecond time-resolved two-photon photoemission (TR-2PPE) spectroscopy is attracting much interest because of its capability to observe the energy-resolved excited electron dynamics. In this work, we have carried out a TR-2PPE study of the organic semiconductor copper phthalocyanine (CuPc) film. Furthermore, we have investigated the detailed electronic structure of CuPc film using the photoemission (PES) and inverse photoemission (IPES) spectroscopies. From the simultaneous PES and IPES measurements for CuPc film with a thickness of 100 nm, the lowest unoccupied molecular orbital (LUMO), highest occupied molecular orbital, and ionization potential of CuPc film have been directly determined. The observed two-photon photoemission (2PPE) spectrum of the present CuPc film, measured with photon energy of about hv=3.3 eV, exhibits a broad feature. From the energy diagram of CuPc film determined by the PES and IPES measurements, the intermediate state observed in the present 2PPE spectrum of CuPc film corresponds to the energy region between about 0.4 and 1.7 eV above the LUMO energy. From the time-resolved pump-probe measurements, it is found that the relaxation lifetimes of excited states in the present CuPc films are very short (all below 50 fs) and monotonously become faster with increasing excitation energy. We attribute this extremely fast relaxation process of photoexcitation to a rapid internal conversion process. From these results

Low-temperature synthesis of diamond films by photoemission-assisted plasma-enhanced chemical vapor deposition

Energy Technology Data Exchange (ETDEWEB)

Kawata, Mayuri, E-mail: kawata@mail.tagen.tohoku.ac.jp; Ojiro, Yoshihiro; Ogawa, Shuichi; Takakuwa, Yuji [Institute of Multidisciplinary Research for Advanced Materials, Tohoku University, 2-1-1 Katahira, Aoba-ku, Sendai 980-8577 (Japan); Masuzawa, Tomoaki; Okano, Ken [International Christian University, 3-10-2 Osawa, Mitaka 181-8585 (Japan)

2014-03-15

Photoemission-assisted plasma-enhanced chemical vapor deposition (PA-PECVD), a process in which photoelectrons emitted from a substrate irradiated with ultraviolet light are utilized as a trigger for DC discharge, was investigated in this study; specifically, the DC discharge characteristics of PA-PECVD were examined for an Si substrate deposited in advance through hot-filament chemical vapor deposition with a nitrogen-doped diamond layer of thickness ∼1 μm. Using a commercially available Xe excimer lamp (hν = 7.2 eV) to illuminate the diamond surface with and without hydrogen termination, the photocurrents were found to be 3.17 × 10{sup 12} and 2.11 × 10{sup 11} electrons/cm{sup 2}/s, respectively. The 15-fold increase in photocurrent was ascribed to negative electron affinity (NEA) caused by hydrogen termination on the diamond surfaces. The DC discharge characteristics revealed that a transition bias voltage from a Townsend-to-glow discharge was considerably decreased because of NEA (from 490 to 373 V for H{sub 2} gas and from 330 to 200 V for Ar gas), enabling a reduction in electric power consumption needed to synthesize diamond films through PA-PECVD. In fact, the authors have succeeded in growing high-quality diamond films of area 2.0 cm{sup 2} at 540 °C with a discharge power of only 1.8 W, plasma voltage of 156.4 V, and discharge current of 11.7 mA under the glow discharge of CH{sub 4}/H{sub 2}/Ar mixed gases. In addition to having only negligible amounts of graphite and amorphous carbon, the diamond films exhibit a relatively high diamond growth rate of 0.5 μm/h at temperatures as low as 540 °C, which is attributed to Ar{sup +} ions impinging on the diamond surface, and causing the removal of hydrogen atoms from the surface through sputtering. This process leads to enhanced CH{sub x} radical adsorption, because the sample was applied with a negative potential to accelerate photoelectrons in PA-PECVD.

Photoemission study of Ca-intercalated graphite superconductor CaC6

International Nuclear Information System (INIS)

Okazaki, Hiroyuki; Yoshida, Rikiya; Iwai, Keisuke; Noami, Kengo; Muro, Takayuki; Nakamura, Tetsuya; Wakita, Takanori; Muraoka, Yuji; Hirai, Masaaki; Tomioka, Fumiaki; Takano, Yoshihiko; Takenaka, Asami; Toyoda, Masahiro; Oguchi, Tamio; Yokoya, Takayoshi

2010-01-01

In this work, we have performed resonant photoemission studies of Ca-intercalated graphite superconductor CaC 6 . Using photon energy of the Ca 2p-3d threshold, the photoemission intensity of the peak at Fermi energy (E F ) is resonantly enhanced. This result provides spectroscopic evidence for the existence of Ca 3d states at E F , and strongly supports that Ca 3d state plays a crucial role for the superconductivity of this material with relatively high T c .

Efficient photoemission from robust ferroelectric ceramics

International Nuclear Information System (INIS)

Boscolo, I.; Castellano, M.; Catani, L.; Ferrario, M.; Tazzioli, F.; Giannessi, L.

1999-01-01

Experimental results on photoemission by ferroelectric ceramic disks, with a possible interpretation, are present. Two types of lead zirconate titanate lanthanum doped, PLZT, ceramics have been used for tests. 25 ps light pulses of 532 and 355 nm were used for excitation. The intensity ranged within the interval 0.1-3 GW/cm 2. The upper limit of the intensity was established by the damage threshold tested by the onset of ion emission. At low value of the intensity the yield was comparable at the two wavelengths. At the highest intensity of green light the emitted charge was 1 nC per 10 mm 2, but it was limited by the space charge effect. In fact, the applied field was only 20 kV/cm, allowed both by the mechanical design of the apparatus and the poor vacuum, 10 - 4 mbar. No surface processing was required. The measurement of the electron pulse length under way

Photoemission study of K on graphite

NARCIS (Netherlands)

Bennich, P.; Puglia, C.; Brühwiler, P.A.; Nilsson, A.; Sandell, A.; Mårtensson, N.; Rudolf, P.

1999-01-01

The physical and electronic structure of the dispersed and (2×2) phases of K/graphite have been characterized by valence and core-level photoemission. Charge transfer from K to graphite is found to occur at all coverages, and includes transfer of charge to the second graphite layer. A rigid band

Photoemission Experiments for Charge Characteristics of Individual Dust Grains

Science.gov (United States)

Abbas, M. M.; Spann, James F., Jr.; Craven, Paul D.; West, E.; Pratico, Jared; Scheianu, D.; Tankosic, D.; Venturini, C. C.; Whitaker, Ann F. (Technical Monitor)

2001-01-01

Photoemission experiments with UV radiation have been performed to investigate the microphysics and charge characteristics of individual isolated dust grains of various compositions and sizes by using the electrodynamic balance facility at NASA Marshall Space Flight Center. Dust particles of 1 - 100 micrometer diameter are levitated in a vacuum chamber at pressures approx. 10(exp -5) torr and exposed to a collimated beam of UV radiation in the 120-300 nanometers spectral range from a deuterium lamp source with a MgF2 window. A monochromator is used to select the UV radiation wavelength with a spectral resolution of 8 nanometers. The electrodynamic facility permits measurements of the charge and diameters of particles of known composition, and monitoring of photoemission rates with the incident UV radiation. Experiments have been conducted on Al2O3 and silicate particles, and in particular on JSC-1 Mars regolith simulants, to determine the photoelectron yields and surface equilibrium potentials of dust particles when exposed to UV radiation in the 120-250 micrometers spectral range. A brief discussion of the experimental procedure, the results of photoemission experiments, and comparisons with theoretical models will be presented.

Electron beam assisted field evaporation of insulating nanowires/tubes

Energy Technology Data Exchange (ETDEWEB)

Blanchard, N. P., E-mail: nicholas.blanchard@univ-lyon1.fr; Niguès, A.; Choueib, M.; Perisanu, S.; Ayari, A.; Poncharal, P.; Purcell, S. T.; Siria, A.; Vincent, P. [Institut Lumière Matière, UMR5306 Université Lyon 1-CNRS, Université de Lyon, 69622 Villeurbanne Cedex (France)

2015-05-11

We demonstrate field evaporation of insulating materials, specifically BN nanotubes and undoped Si nanowires, assisted by a convergent electron beam. Electron irradiation leads to positive charging at the nano-object's apex and to an important increase of the local electric field thus inducing field evaporation. Experiments performed both in a transmission electron microscope and in a scanning electron microscope are presented. This technique permits the selective evaporation of individual nanowires in complex materials. Electron assisted field evaporation could be an interesting alternative or complementary to laser induced field desorption used in atom probe tomography of insulating materials.

Rb-intercalated C60 compounds studied by photoemission spectroscopies

International Nuclear Information System (INIS)

Brambilla, A.; Giovanelli, L.; Vilmercati, P.; Cattoni, A.; Biagioni, P.; Goldoni, A.; Finazzi, M.; Duo, L.

2005-01-01

We report on a combined photoemission and inverse photoemission spectroscopy analysis on Rb x C 60 compounds with different stoichiometries (0-bar x-bar 6). Apart from shifts and broadening of the spectral features associated to the different phase formed, we observe in the RbC 60 phase the presence of the highest occupied molecular orbital (HOMO) shoulder and of its symmetric (with respect to the Fermi level) empty state. According to calculations, the metallicity of this phase and the presence of these electronic states may be taken as a fingerprint of the interplay between electron-electron and electron-phonon interactions in determining the electronic behavior of alkali metal fullerides

UNCONTROLLED PHOTOMULTIPLIER CURRENT IN PHOTOEMISSION ANALYSIS

Directory of Open Access Journals (Sweden)

K. A. Viazava

2016-01-01

Full Text Available The dependence of photon energy from energy of photoelectron is base of photoemission radiation analysis. In such photoemission measurements except current of photocathode is always exist a reverse current from the collector of electrons to the photocathode in two-electrode sensors. There are various ways of reverse and uncontrolled current eliminating or reducing their influence. The constructive method is based on creating an electron-optical system of photoelectronic device, which would be a photoelectron energy analyzer. The second method – technological. However, it requires the manufacture of the photocathode and the dynode system in different vacuum chamber with subsequent connection to a single device in vacuum environment without exposure to the atmosphere. The purpose of this article is to determinate the effect of photoemission from photocathode chamber and the first dynode of photomultiplier on energy distribution of the photoelectrons from photocathode. To solve this problem authors obtained calibration curves for measuring pyrometer module ПИФ 4/2 with ФЭУ-114 as a sensor at supply voltage 1350 V and different decelerating voltages. The effect of illumination on the value of modulation coefficient on temperature k(T and wavelength k(λ is shown. In temperature measurements, this effect is evident in fact that at temperatures below 1400 K linear dependence ln k – T-1 is broken. Still this linear dependence is a necessary consequence of the fact that the measured temperature is color temperature. However, this calibration curve can be used to measure low temperature if the target measurements condition and calibration conditions are identical. In wavelength calibration, curve k(λ at λ > 760 nm is two-valued, that doesn’t allow to identify monochromatic radiation by this method and bring in errors in temperature measurements. 

Photoemission from valence bands of transition metal-phthalocyanines

International Nuclear Information System (INIS)

Shang, Ming-Hui; Nagaosa, Mayumi; Nagamatsu, Shin-ichi; Hosoumi, Shunsuke; Kera, Satoshi; Fujikawa, Takashi; Ueno, Nobuo

2011-01-01

Research highlights: → The HOMO mainly comes from the carbon atoms of Pc rings and the central metal atoms almost have no contribution on the highest occupied molecular orbital (HOMO: a 1u ) distribution of CoPc as well as NiPc. → Influence by central metal atom on the photoemission intensities from the HOMO of two single molecule systems is negligible for the major. → The modification of the distribution for π-orbital upon adsorption as well as the scattering effects of the central metal on the photoemission intensities are negligible for the major. - Abstract: Angular dependencies of ultraviolet photoelectron spectrum of transition metal-phthalocyanines (TM-Pcs), NiPc and CoPc, have been studied by using multiple-scattering theory to explore the electronic structure of the organometallic complexes influenced by central metal atom. The calculated angular distributions of photoelectrons for the highest occupied molecular orbital (HOMO: a 1u ) from the two single systems are nearly the same and represent well the experimental results obtained for the well-ordered monolayer on the highly oriented pyrolytic graphite substrate. The central metal atoms almost have no contribution on the HOMO distribution, which mainly comes from the carbon atoms of Pc ring. Moreover, the modification of the distribution for π orbital upon adsorption as well as the scattering effects of the central metal on the photoemission intensities are negligible for the major.

Effect of wave-function localization on the time delay in photoemission from surfaces

International Nuclear Information System (INIS)

Zhang, C.-H.; Thumm, U.

2011-01-01

We investigate streaking time delays in the photoemission from a solid model surface as a function of the degree of localization of the initial-state wave functions. We consider a one-dimensional slab with lattice constant a latt of attractive Gaussian-shaped core potentials of width σ. The parameter σ/a latt thus controls the overlap between adjacent core potentials and localization of the electronic eigenfunctions on the lattice points. Small values of σ/a latt latt > or approx 0.4. By numerically solving the time-dependent Schroedinger equation, we calculate photoemission spectra from which we deduce a characteristic bimodal shape of the band-averaged photoemission time delay: as the slab eigenfunctions become increasingly delocalized, the time delay quickly decreases near σ/a latt =0.3 from relatively large values below σ/a latt ∼0.2 to much smaller delays above σ/a latt ∼0.4. This change in wave-function localization facilitates the interpretation of a recently measured apparent relative time delay between the photoemission from core and conduction-band levels of a tungsten surface.

Electronic structure of beta-FeSi sub 2 obtained by maximum entropy method and photoemission spectroscopy

CERN Document Server

Kakemoto, H; Makita, Y; Kino, Y; Tsukamoto, T; Shin, S; Wada, S; Tsurumi, T

2003-01-01

The electronic structure of beta-FeSi sub 2 was investigated by maximum entropy method (MEM) and photoemission spectroscopy. The electronic structure obtained by MEM using X-ray diffraction data at room temperature (RT) showed covalent bonds of Fe-Si and Si-Si electrons. The photoemission spectra of beta-FeSi sub 2 at RT were changed by incidence photon energies. For photon energies between 50 and 100 eV, resonant photoemission spectra caused by a super Coster-Kronig transition were observed. In order to reduce resonant effect about Fe(3d) for obtained photoemission spectra, difference spectrum between 53 and 57 eV was calculated, and it was compared with ab-initio band calculation and spectra function.

Development of high current electron source using photoemission from metals with ultrashort laser pulses

International Nuclear Information System (INIS)

Tsang, T.; Srinivasan-Rao, T.; Fischer, J.

1990-10-01

We summarize the studies of photoemission from metal photocathodes using picosecond pulses in the UV (4.66 eV) wavelength and femtosecond laser pulses in the visible (2 eV) wavelengths. To achieve high current density yield from metal photocathodes, multiphoton photoemission using femtosecond laser pulses are suggested. Electron yield improvement incorporating surface photoemission and surface plasmon resonance in metals and metal films are demonstrated. We examine the possibility of the nonlinear photoemission process overtaking the linear process, and identity some possible complexity. To extract the large amount of electrons free of space charge, a pulsed high voltage is designed; the results of the preliminary test are presented. Finally, for the first time, the width of the electron temporal profiles are measured, utilizing the nonlinear photoelectric effect, to below 100 fsec time regime. The results indicated that the electron pulse duration follows the laser pulses and are not limited by the material. 8 refs., 15 figs

Angle-resolved photoemission investigation of SmB{sub 6}

Energy Technology Data Exchange (ETDEWEB)

Hlawenka, Peter; Rader, Oliver; Siemensmeyer, Konrad; Weschke, Eugen; Varykhalov, Andrei; Rienks, Emile [Helmholtz-Zentrum Berlin (Germany); Shitsevalova, Natalya [Institute for Problems of Material Science, Kiev (Ukraine); Gabani, Slavomir; Flachbart, Karol [IEP, Slovak Academy of Science, Kosice (Slovakia)

2015-07-01

Recently the mixed valence compound SmB{sub 6} has drawn great attention. Theoretically predicted surface states, which should result from a hybridisation of localised f-bands with conduction electrons and a band inversion, would make SmB{sub 6} the first realisation of a so called topological Kondo insulator. Conductivity and transport measurements, as well as spin-resolved photoemission spectroscopy seem to fortify the scenario of a topological nature of the conductive surface. We investigate the surface electronic structure of SmB{sub 6} by means of high resolution angle-resolved photoemission spectroscopy measurements below 1 K. We will present new insights into the surface states that determine the low temperature conductivity of this material.

Time-resolved magnetic imaging in an aberration-corrected, energy-filtered photoemission electron microscope

International Nuclear Information System (INIS)

Nickel, F.; Gottlob, D.M.; Krug, I.P.; Doganay, H.; Cramm, S.; Kaiser, A.M.; Lin, G.; Makarov, D.; Schmidt, O.G.

2013-01-01

We report on the implementation and usage of a synchrotron-based time-resolving operation mode in an aberration-corrected, energy-filtered photoemission electron microscope. The setup consists of a new type of sample holder, which enables fast magnetization reversal of the sample by sub-ns pulses of up to 10 mT. Within the sample holder current pulses are generated by a fast avalanche photo diode and transformed into magnetic fields by means of a microstrip line. For more efficient use of the synchrotron time structure, we developed an electrostatic deflection gating mechanism capable of beam blanking within a few nanoseconds. This allows us to operate the setup in the hybrid bunch mode of the storage ring facility, selecting one or several bright singular light pulses which are temporally well-separated from the normal high-intensity multibunch pulse pattern. - Highlights: • A new time-resolving operation mode in photoemission electron microscopy is shown. • Our setup works within an energy-filtered, aberration-corrected PEEM. • A new gating system for bunch selection using synchrotron radiation is developed. • An alternative magnetic excitation system is developed. • First tr-imaging using an energy-filtered, aberration-corrected PEEM is shown

Notes on photon assisted field ionization

International Nuclear Information System (INIS)

Niu, B.H.C.; Bryant, P.J.

1979-01-01

A response to comments by Viswanathan et al (2) on a previous publication(1) by the authors is given. It is contended that the original hypothesis of photon assisted field ionization at metal surfaces correctly explains the results reported in Ref. 1

A Dust Grain Photoemission Experiment

Science.gov (United States)

Venturini, C. C.; Spann, J. F., Jr.; Abbas, M. M.; Comfort, R. H.

2000-01-01

A laboratory experiment has been developed at Marshall Space Flight Center to study the interaction of micron-sized particles with plasmas and FUV radiation. The intent is to investigate the conditions under which particles of various compositions and sizes become charged, or discharged, while exposed to an electron beam and/or UV radiation. This experiment uses a unique laboratory where a single charged micron size particle is suspended in a quadrupole trap and then subjected to a controlled environment. Tests are performed using different materials and sizes, ranging from 10 microns to 1 micron, to determine the particle's charge while being subjected to an electron beam and /or UV radiation. The focus of this presentation will be on preliminary results from UV photoemission tests, but past results from electron beam, secondary electron emission tests will also be highlighted. A monochromator is used to spectrally resolve UV in the 120 nm to 300 nm range. This enables photoemission measurements as a function of wavelength. Electron beam tests are conducted using I to 3 micron sized aluminum oxide particles subjected to energies between 100 eV to 3 KeV. It was found that for both positive and negative particles the potential tended toward neutrality over time with possible equilibrium potentials between -0.8 Volts and 0.8 Volts.

Optical field emission from resonant gold nanorods driven by femtosecond mid-infrared pulses

Energy Technology Data Exchange (ETDEWEB)

Kusa, F. [Department of Applied Physics, Tokyo University of Agriculture and Technology, 2-24-16 Nakacho, Koganei Tokyo 184-8588 (Japan); Institute of Industrial Science, the University of Tokyo, 4-6-1 Komaba, Meguro-ku, Tokyo 153-8505 (Japan); Echternkamp, K. E.; Herink, G.; Ropers, C. [4th Physical Institute – Solids and Nanostructures, University of Göttingen, 37077 Göttingen (Germany); Ashihara, S., E-mail: ashihara@iis.u-tokyo.ac.jp [Institute of Industrial Science, the University of Tokyo, 4-6-1 Komaba, Meguro-ku, Tokyo 153-8505 (Japan)

2015-07-15

We demonstrate strong-field photoelectron emission from gold nanorods driven by femtosecond mid-infrared optical pulses. The maximum photoelectron yield is reached at the localized surface plasmon resonance, indicating that the photoemission is governed by the resonantly-enhanced optical near-field. The wavelength- and field-dependent photoemission yield allows for a noninvasive determination of local field enhancements, and we obtain intensity enhancement factors close to 1300, in good agreement with finite-difference time domain computations.

Significant relaxation of residual negative carrier in polar Alq3 film directly detected by high-sensitivity photoemission

Science.gov (United States)

Kinjo, Hiroumi; Lim, Hyunsoo; Sato, Tomoya; Noguchi, Yutaka; Nakayama, Yasuo; Ishii, Hisao

2016-02-01

Tris(8-hydroxyquinoline)aluminum (Alq3) has been widely applied as a good electron-injecting layer (EIL) in organic light-emitting diodes. High-sensitivity photoemission measurement revealed a clear photoemission by visible light, although its ionization energy is 5.7 eV. This unusual photoemission is ascribed to Alq3 anions captured by positive polarization charges. The observed electron detachment energy of the anion was about 1 eV larger than the electron affinity reported by inverse photoemission. This difference suggests that the injected electron in the Alq3 layer is energetically relaxed, leading to the reduction in injection barrier. This nature is one of the reasons why Alq3 worked well as the EIL.

A tunable low-energy photon source for high-resolution angle-resolved photoemission spectroscopy

International Nuclear Information System (INIS)

Harter, John W.; Monkman, Eric J.; Shai, Daniel E.; Nie Yuefeng; Uchida, Masaki; Burganov, Bulat; Chatterjee, Shouvik; King, Philip D. C.; Shen, Kyle M.

2012-01-01

We describe a tunable low-energy photon source consisting of a laser-driven xenon plasma lamp coupled to a Czerny-Turner monochromator. The combined tunability, brightness, and narrow spectral bandwidth make this light source useful in laboratory-based high-resolution photoemission spectroscopy experiments. The source supplies photons with energies up to ∼7 eV, delivering under typical conditions >10 12 ph/s within a 10 meV spectral bandwidth, which is comparable to helium plasma lamps and many synchrotron beamlines. We first describe the lamp and monochromator system and then characterize its output, with attention to those parameters which are of interest for photoemission experiments. Finally, we present angle-resolved photoemission spectroscopy data using the light source and compare its performance to a conventional helium plasma lamp.

Annual report of the Laboratory for Condensed Matter Physics, and the Biophysics Group

International Nuclear Information System (INIS)

1986-01-01

Research on photoemission and photoluminescence in quantum wells; photoemission assisted by electric fields; the electrochemistry of the semiconductor-electrolyte interface; MESFET's; fractal physics; amorphous silicon; superionic and mixed conductors; solids chemistry and NMR; internal motion of nucleic acids; cardiophysiology; imaging of microscopic internal motions; and Ap4A metabolism is presented [fr

Nonrelativistic quantum electrodynamic approach to photoemission theory

International Nuclear Information System (INIS)

Fujikawa, Takashi; Arai, Hiroko

2005-01-01

A new nonrelativistic many-body theory to analyze X-ray photoelectron spectroscopy (XPS) spectra has been developed on the basis of quantum electrodynamic (QED) Keldysh Green's function approach. To obtain XPS current density we calculate electron Green's function g which partly includes electron-photon interactions. We first separate longitudinal and transverse parts of these Green's functions in the Coulomb gauge. The transverse electron selfenergy describes the electron-photon interaction, whereas the longitudinal electron selfenergy describes the electron-electron interaction. We derive the QED Hedin's equation from which we obtain systematic skeleton expansion in the power series of the screened Coulomb interaction W and the photon Green's function D kl . We show the present theory provides a sound theoretical tool to study complicated many-body processes such as the electron propagation damping, intrinsic, extrinsic losses and their interference, and furthermore, resonant photoemission processes. We have also found the importance of the mixed photon Green's functions D 0k and D k0 which have been supposed to be unimportant for the XPS analyses. They, however, directly describe the radiation field screening. In this work, photon field screening effects are discussed in one-step theory, where the electron-photon interaction operator Δ is proved to be replaced by ε -1 Δ beyond linear approximation. Beyond free photon Green's function approximation, photon scatterings from the electron density are incorporated within the present QED theory. These photon field effects can directly describe the microscopic photon field spatial variation specific to near the surface region and nanoparticle systems

Visualizing electron dynamics in organic materials: Charge transport through molecules and angular resolved photoemission

Science.gov (United States)

Kümmel, Stephan

Being able to visualize the dynamics of electrons in organic materials is a fascinating perspective. Simulations based on time-dependent density functional theory allow to realize this hope, as they visualize the flow of charge through molecular structures in real-space and real-time. We here present results on two fundamental processes: Photoemission from organic semiconductor molecules and charge transport through molecular structures. In the first part we demonstrate that angular resolved photoemission intensities - from both theory and experiment - can often be interpreted as a visualization of molecular orbitals. However, counter-intuitive quantum-mechanical electron dynamics such as emission perpendicular to the direction of the electrical field can substantially alter the picture, adding surprising features to the molecular orbital interpretation. In a second study we calculate the flow of charge through conjugated molecules. The calculations show in real time how breaks in the conjugation can lead to a local buildup of charge and the formation of local electrical dipoles. These can interact with neighboring molecular chains. As a consequence, collections of ''molecular electrical wires'' can show distinctly different characteristics than ''classical electrical wires''. German Science Foundation GRK 1640.

The Plate Boundary Observatory Student Field Assistant Program in Southern California

Science.gov (United States)

Seider, E. L.

2007-12-01

Each summer, UNAVCO hires students as part of the Plate Boundary Observatory (PBO) Student Field Assistant Program. PBO, the geodetic component of the NSF-funded EarthScope project, involves the reconnaissance, permitting, installation, documentation, and maintenance of 880 permanent GPS stations in five years. During the summer 2007, nine students from around the US and Puerto Rico were hired to assist PBO engineers during the busy summer field season. From June to September, students worked closely with PBO field engineers to install and maintain permanent GPS stations in all regions of PBO, including Alaska. The PBO Student Field Assistant Program provides students with professional hands-on field experience as well as continuing education in the geosciences. It also gives students a glimpse into the increasing technologies available to the science community, the scope of geophysical research utilizing these technologies, and the field techniques necessary to complete this research. Students in the PBO Field Assistant Program are involved in all aspects of GPS support, including in-warehouse preparation and in-field installations and maintenance. Students are taught practical skills such as drilling, wiring, welding, hardware configuration, documentation, and proper field safety procedures needed to construct permanent GPS stations. These real world experiences provide the students with technical and professional skills that are not always available to them in a classroom, and will benefit them greatly in their future studies and careers. The 2007 summer field season in Southern California consisted of over 35 GPS permanent station installations. To date, the Southern California region of PBO has installed over 190 GPS stations. This poster presentation will highlight the experiences gained by the Southern California student field assistants, while supporting PBO- Southern California GPS installations in the Mohave Desert and the Inyo National Forest.

Rb-intercalated C{sub 60} compounds studied by photoemission spectroscopies

Energy Technology Data Exchange (ETDEWEB)

Brambilla, A [INFM - Dipartimento di Fisica, Politecnico di Milano, p.za L. da Vinci 32, I-20133 Milan (Italy); Giovanelli, L [Sincrotrone Trieste S.C.p.A., Strada Statale 14, Km 163.5, I-34012 Basovizza, Trieste (Italy); Vilmercati, P [Sincrotrone Trieste S.C.p.A., Strada Statale 14, Km 163.5, I-34012 Basovizza, Trieste (Italy); Cattoni, A [INFM - Dipartimento di Fisica, Politecnico di Milano, p.za L. da Vinci 32, I-20133 Milan (Italy); Biagioni, P [INFM - Dipartimento di Fisica, Politecnico di Milano, p.za L. da Vinci 32, I-20133 Milan (Italy); Goldoni, A [Sincrotrone Trieste S.C.p.A., Strada Statale 14, Km 163.5, I-34012 Basovizza, Trieste (Italy); Finazzi, M [INFM - Dipartimento di Fisica, Politecnico di Milano, p.za L. da Vinci 32, I-20133 Milan (Italy); Duo, L [INFM - Dipartimento di Fisica, Politecnico di Milano, p.za L. da Vinci 32, I-20133 Milan (Italy)

2005-06-15

We report on a combined photoemission and inverse photoemission spectroscopy analysis on Rb{sub x}C{sub 60} compounds with different stoichiometries (0-bar x-bar 6). Apart from shifts and broadening of the spectral features associated to the different phase formed, we observe in the RbC{sub 60} phase the presence of the highest occupied molecular orbital (HOMO) shoulder and of its symmetric (with respect to the Fermi level) empty state. According to calculations, the metallicity of this phase and the presence of these electronic states may be taken as a fingerprint of the interplay between electron-electron and electron-phonon interactions in determining the electronic behavior of alkali metal fullerides.

Annual report of the Laboratory of Condensed Matter Physics, and the Biophysics Group, 1985

International Nuclear Information System (INIS)

1987-01-01

Research on photoemission and photoluminescence in quantum wells; photoemission assisted by electric fields; the electrochemistry of the semiconductor-electrolyte interface; transport properties of MESFET's; fractal physics; amorphous silicon; superionic and mixed conductors; solids chemistry and NMR; internal motion of nucleic acids; cardiophysiology; imaging of microscopic internal motions; and Ap4A metabolism is presented [fr

Many-body effects in X-ray photoemission spectroscopy and electronic properties of solids

International Nuclear Information System (INIS)

Kohiki, S.

1999-01-01

Photoemission from a solid is evidently a many-body process since the motion of each electron cannot be independent of the motions of other electrons. In this article we review the reported many-body effects in X-ray photoemission such as extra-atomic relaxation energy, charge transfer satellite and energy loss structure which are informative in relation to the characteristics of solids. (Copyright (c) 1999 Elsevier Science B.V., Amsterdam. All rights reserved.)

Photoemission studies of clean and adsorbate covered metal surfaces using synchrotron and uv radiation sources

International Nuclear Information System (INIS)

Apai, G.R. II.

1977-09-01

Photoemission energy distribution experiments on clean metal and adsorbate-covered surfaces were performed under ultrahigh vacuum conditions by using x-ray and ultraviolet photon sources in the laboratory as well as continuously-tunable, highly polarized synchrotron radiation obtainable at the Stanford Synchrotron Radiation Laboratory (SSRL). Studies focused on two general areas: cross-section modulation in the photoemission process was studied as a function of photon energy and orbital composition. Sharp decreases in intensity of the valence bands of several transition metals (i.e., Ag, Au, and Pt) are attributed to the radial nodes in the respective wave functions. Adsorbate photoemission studies of CO adsorbed on platinum single crystals have demonstrated a very high spectral sensitivity to the 4sigma and (1π + 5sigma) peaks of CO at photon energies of 150 eV. Angle-resolved photoemission allowed determination of the orientation of CO chemisorbed on a Pt (111) or Ni(111) surface. Prelinimary results at high photon energies (approximately 150 eV) indicated scattering from the substrate which could yield chemisorption site geometries

Zero field reversal probability in thermally assisted magnetization reversal

Science.gov (United States)

Prasetya, E. B.; Utari; Purnama, B.

2017-11-01

This paper discussed about zero field reversal probability in thermally assisted magnetization reversal (TAMR). Appearance of reversal probability in zero field investigated through micromagnetic simulation by solving stochastic Landau-Lifshitz-Gibert (LLG). The perpendicularly anisotropy magnetic dot of 50×50×20 nm3 is considered as single cell magnetic storage of magnetic random acces memory (MRAM). Thermally assisted magnetization reversal was performed by cooling writing process from near/almost Curie point to room temperature on 20 times runs for different randomly magnetized state. The results show that the probability reversal under zero magnetic field decreased with the increase of the energy barrier. The zero-field probability switching of 55% attained for energy barrier of 60 k B T and the reversal probability become zero noted at energy barrier of 2348 k B T. The higest zero-field switching probability of 55% attained for energy barrier of 60 k B T which corespond to magnetif field of 150 Oe for switching.

Photoemission study on the formation of Mo contacts to CuInSe2

International Nuclear Information System (INIS)

Nelson, A.J.; Niles, D.W.; Kazmerski, L.L.; Rioux, D.; Patel, R.; Hoechst, H.

1992-01-01

Synchrotron radiation soft-x-ray photoemission spectroscopy was used to investigate the development of the electronic structure at the Mo/CuInSe 2 interface. Mo overlayers were e-beam deposited in steps on single-crystal n-type CuInSe 2 at ambient temperature. Photoemission measurements were acquired after each growth in order to observe changes in the valence-band electronic structure as well as changes in the In 4d, Se 3d, and Mo 4d core lines. Photoemission measurements on the valence-band and core lines were also obtained after annealing. The results were used to correlate the interface chemistry with the electronic structure at this interface and to directly determine the maximum possible Schottky barrier height φ b to be ≤0.2 eV at the Mo/CuInSe 2 junction before annealing, thus showing that this contact is essentially ohmic

Time-resolved photoemission micro-spectrometer using higher-order harmonics of Ti:sapphire laser

International Nuclear Information System (INIS)

Azuma, J.; Kamada, M.; Kondo, Y.

2004-01-01

Full text: A new photoemission spectrometer is under construction for the photoemission microscopy and the time-resolved pump- probe experiment. The higher order harmonics of the Ti:sapphire laser is used as the light source of the VUV region in this system. Because the fundamental laser is focused tightly into the rare gas jet to generate the higher order harmonics, the spot size of the laser, in other words, the spot size of the VUV light source is smaller than a few tens of micrometer. This smallness of the spot size has advantage for the microscopy. In order to compensate the low flux of the laser harmonics, a multilayer-coated schwaltzshild optics was designed. The multilayers play also as the monochromatic filter. The spatial resolution of this schwaltzshild system is found to be less than 1 micrometer by the ray-tracing calculations. A main chamber of the system is equipped with a time-of-flight energy analyzer to improve the efficiency of the electron detection. The main chamber and the gas chamber are separated by a differential pumping chamber and a thin Al foil. The system is designed for the study of the clean surface. It will be capable to perform the sub-micron photoemission microscopy and the femto-second pump-probe photoemission study for the various photo-excited dynamics on clean surfaces

Optical and photoemission studies of lanthanum hydrides

International Nuclear Information System (INIS)

Peterman, D.J.; Peterson, D.T.; Weaver, J.H.

1980-01-01

The results of optical absorptivity and photoemission measurements on lanthanum hydrides, LaH/sub x/ (1.98 less than or equal to x less than or equal to 2.89) are reported. The low energy (hν less than or equal to 0.5 eV) optical features in LaH/sub x/ are attributed to the filling of octahedral sites. Higher energy interband absorption involves states within the d-band complex, analogous to other dihydrides. As x increases above 2.0, the optical features change rapidly due to the increase in the number of occupied octahedral sites. Various band structure studies suggest that LaH 3 might be a semiconductor. Photoemission results show that as x increases, the d-derived states at E/sub F/ are drawn down and that for LaH 2 89 only very weak valence band emission is observed. The hydrogen-derived bonding bands are shown centered approx. 5 eV below E/sub F/. Observed chemical shifts in the La 5p/sub 1/2 3/2/ cores are discussed for 1.98 less than or equal to x less than or equal to 2.89

Rb-intercalated C60 compounds studied by Inverse Photoemission Spectroscopy

International Nuclear Information System (INIS)

Finazzi, M.; Brambilla, A; Biagioni, P.; Cattoni, A.; Duo, L.; Ciccacci, F.; Braicovich, L.; Giovanelli, L.; Goldoni, A.

2004-01-01

Full text: Since the discovery of superconductivity in alkali-doped solid C 60 , the electronic structure of the host material (C 60 ) and the doped compounds (A x C 60 , where A is an alkali metal), has been the subject of a considerable amount of work, both theoretical and experimental. The spectroscopic investigations of the alkali-doped C 60 compounds has been mainly focussed on the valence states, while much less information is available on the unoccupied states. In particular, inverse photoemission data on the complete set of stable Rb x C 60 compounds was, so far, still missing. We have performed Inverse Photoemission (IPE) spectroscopy on Rb x C 60 compounds (x = 1, 3, 4, 6). IPE spectra were obtained using a band-pass photon detector (hv = 9.4 eV, FWHM = 0.7 eV) and scanning the kinetic energy of the electrons impinging on the sample. Rb was evaporated on C 60 films (thickness = 6-12 atomic layers) grown in situ on a Cu(100) substrate. The temperature of the substrate was kept equal to T = 100 deg C, which is lower than the C 60 sublimation temperature. The amount of Rb was checked by measuring the intensity of the C1s and Rb3d photoemission lines. After the required amount of Rb had been deposited, the samples were annealed to distillate the desired stable phase

Photoemission studies of semiconductor nanocrystals

International Nuclear Information System (INIS)

Hamad, K.S.; Roth, R.; Alivisatos, A.P.

1997-01-01

Semiconductor nanocrystals have been the focus of much attention in the last ten years due predominantly to their size dependent optical properties. Namely, the band gap of nanocrystals exhibits a shift to higher energy with decreasing size due to quantum confinement effects. Research in this field has employed primarily optical techniques to study nanocrystals, and in this respect this system has been investigated extensively. In addition, one is able to synthesize monodisperse, crystalline particles of CdS, CdSe, Si, InP, InAs, as well as CdS/HgS/CdS and CdSe/CdS composites. However, optical spectroscopies have proven ambiguous in determining the degree to which electronic excitations are interior or surface admixtures or giving a complete picture of the density of states. Photoemission is a useful technique for understanding the electronic structure of nanocrystals and the effects of quantum confinement, chemical environments of the nanocrystals, and surface coverages. Of particular interest to the authors is the surface composition and structure of these particles, for they have found that much of the behavior of nanocrystals is governed by their surface. Previously, the authors had performed x-ray photoelectron spectroscopy (XPS) on CdSe nanocrystals. XPS has proven to be a powerful tool in that it allows one to determine the composition of the nanocrystal surface

Electronic Structure of the Kitaev Material α-RuCl3 Probed by Photoemission and Inverse Photoemission Spectroscopies

Science.gov (United States)

Sinn, Soobin; Kim, Choong Hyun; Kim, Beom Hyun; Lee, Kyung Dong; Won, Choong Jae; Oh, Ji Seop; Han, Moonsup; Chang, Young Jun; Hur, Namjung; Sato, Hitoshi; Park, Byeong-Gyu; Kim, Changyoung; Kim, Hyeong-Do; Noh, Tae Won

2016-12-01

Recently, α-RuCl3 has attracted much attention as a possible material to realize the honeycomb Kitaev model of a quantum-spin-liquid state. Although the magnetic properties of α-RuCl3 have been extensively studied, its electronic structure, which is strongly related to its Kitaev physics, is poorly understood. Here, the electronic structure of α-RuCl3 was investigated by photoemission (PE) and inverse-photoemission (IPE) spectroscopies. The band gap was directly measured from the PE and IPE spectra and was found to be 1.9 eV, much larger than previously estimated values. Local density approximation (LDA) calculations showed that the on-site Coulomb interaction U could open the band gap without spin-orbit coupling (SOC). However, the SOC should also be incorporated to reproduce the proper gap size, indicating that the interplay between U and SOC plays an essential role. Several features of the PE and IPE spectra could not be explained by the results of LDA calculations. To explain such discrepancies, we performed configuration-interaction calculations for a RuCl63- cluster. The experimental data and calculations demonstrated that the 4d compound α-RuCl3 is a Jeff = 1/2 Mott insulator rather than a quasimolecular-orbital insulator. Our study also provides important physical parameters required for verifying the proposed Kitaev physics in α-RuCl3.

Smart Rotorcraft Field Assistants for Terrestrial and Planetary Science

Science.gov (United States)

Young, Larry A.; Aiken, Edwin W.; Briggs, Geoffrey A.

2004-01-01

Field science in extreme terrestrial environments is often difficult and sometimes dangerous. Field seasons are also often short in duration. Robotic field assistants, particularly small highly mobile rotary-wing platforms, have the potential to significantly augment a field season's scientific return on investment for geology and astrobiology researchers by providing an entirely new suite of sophisticated field tools. Robotic rotorcraft and other vertical lift planetary aerial vehicle also hold promise for supporting planetary science missions.

Electric Field-Assisted Pressureless Sintering of Ceramic Protonic Conductors

DEFF Research Database (Denmark)

Muccillo, R.; Esposito, Vincenzo; Zanetti De Florio, Daniel

2017-01-01

Gadolinium, yttrium and samarium-doped barium cerate (BCGd, BCY and BCSm, respectively) polycrystalline green pellets were submitted to electric field-assisted pressureless sintering experiments isothermally in the temperature range 800-1200oC under 100-200 V cm-1 electric fields, limiting to 1-5...

Field-assisted synthesis of SERS-active silver nanoparticles using conducting polymers

Science.gov (United States)

Xu, Ping; Jeon, Sea-Ho; Mack, Nathan H.; Doorn, Stephen K.; Williams, Darrick J.; Han, Xijiang; Wang, Hsing-Lin

2010-08-01

A gradient of novel silver nanostructures with widely varying sizes and morphologies is fabricated on a single conducting polyaniline-graphite (P-G) membrane with the assistance of an external electric field. It is believed that the formation of such a silver gradient is a synergetic consequence of the generation of a silver ion concentration gradient along with an electrokinetic flow of silver ions in the field-assisted model, which greatly influences the nucleation and growth mechanism of Ag particles on the P-G membrane. The produced silver dendrites, flowers and microspheres, with sharp edges, intersections and bifurcations, all present strong surface enhanced Raman spectroscopy (SERS) responses toward an organic target molecule, mercaptobenzoic acid (MBA). This facile field-assisted synthesis of Ag nanoparticles via chemical reduction presents an alternative approach to nanomaterial fabrication, which can yield a wide range of unique structures with enhanced optical properties that were previously inaccessible by other synthetic routes.A gradient of novel silver nanostructures with widely varying sizes and morphologies is fabricated on a single conducting polyaniline-graphite (P-G) membrane with the assistance of an external electric field. It is believed that the formation of such a silver gradient is a synergetic consequence of the generation of a silver ion concentration gradient along with an electrokinetic flow of silver ions in the field-assisted model, which greatly influences the nucleation and growth mechanism of Ag particles on the P-G membrane. The produced silver dendrites, flowers and microspheres, with sharp edges, intersections and bifurcations, all present strong surface enhanced Raman spectroscopy (SERS) responses toward an organic target molecule, mercaptobenzoic acid (MBA). This facile field-assisted synthesis of Ag nanoparticles via chemical reduction presents an alternative approach to nanomaterial fabrication, which can yield a wide range

Evaluation of the fluorinated antisticking layer by using photoemission and NEXAFS spectroscopies

Energy Technology Data Exchange (ETDEWEB)

Haruyama, Yuichi; Nakai, Yasuki; Matsui, Shinji [University of Hyogo, Graduate School of Science, Laboratory of Advanced Science and Technology for Industry, Ako, Hyogo (Japan)

2015-11-15

The electronic structures of four kinds of fluorinated self-assembled monolayers (F-SAMs) with different chain length, which were used for an antisticking layer, were investigated by the photoemission and the near-edge X-ray absorption fine structure (NEXAFS) spectroscopies. From the photoemission spectra in the wide and in the C 1s core-level regions, chemical compositions and components of the F-SAMs with different chain length were evaluated. By using the curve fitting analysis of the photoemission spectra in C 1s core-level region, it was found that the CF{sub 3} site is located at the top of the surface in the C sites of the F-SAM. From the C K-edge NEXAFS spectra of the F-SAMs as a function of the incidence angle of the excitation photon, it was shown that the σ*(C-F) and σ*(C-C) orbitals in the F-SAMs are parallel and perpendicular to the surface, respectively. This indicates that the C-C chain in (CF{sub 2}){sub n} part of the F-SAMs is perpendicular to the surface. Based on these results, the electronic structures of the F-SAMs are discussed. (orig.)

Photoemission and photoionization time delays and rates

Science.gov (United States)

Gallmann, L.; Jordan, I.; Wörner, H. J.; Castiglioni, L.; Hengsberger, M.; Osterwalder, J.; Arrell, C. A.; Chergui, M.; Liberatore, E.; Rothlisberger, U.; Keller, U.

2017-01-01

Ionization and, in particular, ionization through the interaction with light play an important role in fundamental processes in physics, chemistry, and biology. In recent years, we have seen tremendous advances in our ability to measure the dynamics of photo-induced ionization in various systems in the gas, liquid, or solid phase. In this review, we will define the parameters used for quantifying these dynamics. We give a brief overview of some of the most important ionization processes and how to resolve the associated time delays and rates. With regard to time delays, we ask the question: how long does it take to remove an electron from an atom, molecule, or solid? With regard to rates, we ask the question: how many electrons are emitted in a given unit of time? We present state-of-the-art results on ionization and photoemission time delays and rates. Our review starts with the simplest physical systems: the attosecond dynamics of single-photon and tunnel ionization of atoms in the gas phase. We then extend the discussion to molecular gases and ionization of liquid targets. Finally, we present the measurements of ionization delays in femto- and attosecond photoemission from the solid–vacuum interface. PMID:29308414

Photoemission and photoionization time delays and rates

Directory of Open Access Journals (Sweden)

L. Gallmann

2017-11-01

Full Text Available Ionization and, in particular, ionization through the interaction with light play an important role in fundamental processes in physics, chemistry, and biology. In recent years, we have seen tremendous advances in our ability to measure the dynamics of photo-induced ionization in various systems in the gas, liquid, or solid phase. In this review, we will define the parameters used for quantifying these dynamics. We give a brief overview of some of the most important ionization processes and how to resolve the associated time delays and rates. With regard to time delays, we ask the question: how long does it take to remove an electron from an atom, molecule, or solid? With regard to rates, we ask the question: how many electrons are emitted in a given unit of time? We present state-of-the-art results on ionization and photoemission time delays and rates. Our review starts with the simplest physical systems: the attosecond dynamics of single-photon and tunnel ionization of atoms in the gas phase. We then extend the discussion to molecular gases and ionization of liquid targets. Finally, we present the measurements of ionization delays in femto- and attosecond photoemission from the solid–vacuum interface.

Scanning photoemission microscopy with synchrotron radiation

Science.gov (United States)

Ade, Harald W.

1992-08-01

Progress in photoemission spectro-microscopy at various synchrotron radiation facilities is reviewed. Microprobe devices such as MAXIMUM at the SRC in Wisconsin, the X1-SPEM at the NSLS at BNL, as well as the ellipsoidal ring mirror microscope at DESY in Hamburg, recorded first images during the last few years. The present status of these devices which achieve their lateral resolution by focusing X-rays to a small spot is the primary focus of this paper, but work representing other approaches to spectro-microscopy is also discussed.

Spin-polarized photoemission

International Nuclear Information System (INIS)

Johnson, Peter D.

1997-01-01

Spin-polarized photoemission has developed into a versatile tool for the study of surface and thin film magnetism. In this review, we examine the methodology of the technique and its application to a number of different problems, including both valence band and core level studies. After a detailed review of spin-polarization measurement techniques and the related experimental requirements we consider in detail studies of the bulk properties both above and below the Curie temperature. This section also includes a discussion of observations relating to unique metastable phases obtained via epitaxial growth. The application of the technique to the study of surfaces, both clean and adsorbate covered, is reviewed. The report then examines, in detail, studies of the spin-polarized electronic structure of thin films and the related interfacial magnetism. Finally, observations of spin-polarized quantum well states in non-magnetic thin films are discussed with particular reference to their mediation of the oscillatory exchange coupling in related magnetic multilayers. (author)

DC photoemission electron guns as ERL sources

International Nuclear Information System (INIS)

Sinclair, Charles K.

2006-01-01

Very-high-voltage DC electron guns, delivering moderate duration bunches from photoemission cathodes, and followed by conventional drift bunching and acceleration, offer a practical solution for an ERL injector. In a variant of this scheme, a DC gun is placed in close proximity to a superconducting RF accelerator cavity, with few or no active elements between the gun and cavity. The principal technical challenge with such electron guns arises from field emission from the cathode electrode and its support structure. Field emission may result in voltage breakdown across the cathode-anode gap, or a punch-through failure of the insulator holding off the cathode potential, as well as lesser though still serious problems. Various means to mitigate these problems are described. The operational lifetime of high quantum efficiency photocathodes in these guns is determined by the vacuum conditions, through phenomena such as chemical poisoning and ion back-bombardment. Minimization of the field strength on electrode structures pushes high-voltage DC guns toward large dimensions and, correspondingly, large outgassing loads, but it is also true that these guns offer many opportunities for achieving excellent vacuum conditions. Good solutions to vacuum problems that had previously limited cathode lifetime have been demonstrated in recent years. Designs for DC guns presently in use and planned for the near future will be described. The parameters necessary for a 100 mA average current, very-high-voltage DC gun with a photocathode operational lifetime greater than 100 h appear to be within reach, but have yet to be demonstrated. A 1 A average current source with good cathode operational lifetime will require developments beyond the present state-of-the-art

A high-DC-voltage GaAs photoemission gun: Transverse emittance and momentum spread measurements

International Nuclear Information System (INIS)

Engwall, D.; Bohn, C.; Cardman, L.

1997-01-01

We have built a high-DC-voltage photoemission gun and a diagnostic beamline permitting us to measure rms transverse emittance (ε x ) and rms momentum spread (δ) of short-duration electron pulses produced by illuminating the cathode with light from a mode-locked, frequency-doubled Nd:YLF laser. The electron gun is a GaAs photocathode source designed to operate at 500kV. We have measured ε x and δ for conditions ranging from emittance-dominated to space-charge-dominated. We report these measurements as functions of microbunch charge for different beam radii, pulse lengths, and voltages/field gradients at the cathode, and compare them with PARMELA calculations

Resonant photoemission study of CeRu4Sb12

International Nuclear Information System (INIS)

Ishii, Hiroyoshi; Miyahara, Tsuneaki; Takayama, Yasuhiro; Shiozawa, Hidetsugu; Obu, Kenji; Matsuda, Tatsuma D.; Aoki, Yuji; Sugawara, Hitoshi; Sato, Hideyuki

2005-01-01

We have measured the Ce 4d-4f and Ce 3d-4f resonant photoemission spectra of CeRu 4 Sb 12 . The Ce 4f spectra show the spectral features corresponding to a weakly hybridized system. The number of 4f electrons is estimated to be ∼1.0

New developments in laser-based photoemission spectroscopy and its scientific applications: a key issues review

Science.gov (United States)

Zhou, Xingjiang; He, Shaolong; Liu, Guodong; Zhao, Lin; Yu, Li; Zhang, Wentao

2018-06-01

The significant progress in angle-resolved photoemission spectroscopy (ARPES) in last three decades has elevated it from a traditional band mapping tool to a precise probe of many-body interactions and dynamics of quasiparticles in complex quantum systems. The recent developments of deep ultraviolet (DUV, including ultraviolet and vacuum ultraviolet) laser-based ARPES have further pushed this technique to a new level. In this paper, we review some latest developments in DUV laser-based photoemission systems, including the super-high energy and momentum resolution ARPES, the spin-resolved ARPES, the time-of-flight ARPES, and the time-resolved ARPES. We also highlight some scientific applications in the study of electronic structure in unconventional superconductors and topological materials using these state-of-the-art DUV laser-based ARPES. Finally we provide our perspectives on the future directions in the development of laser-based photoemission systems.

A study: Effect of Students Peer Assisted Learning on Magnetic Field Achievement

International Nuclear Information System (INIS)

Mueanploy, Wannapa

2016-01-01

This study is the case study of Physic II Course for students of Pathumwan Institute of Technology. The purpose of this study is: 1) to develop cooperative learning method of peer assisted learning (PAL), 2) to compare the learning achievement before and after studied magnetic field lesson by cooperative learning method of peer assisted learning. The population was engineering students of Pathumwan Institute of Technology (PIT’s students) who registered Physic II Course during year 2014. The sample used in this study was selected from the 72 students who passed in Physic I Course. The control groups learning magnetic fields by Traditional Method (TM) and experimental groups learning magnetic field by method of peers assisted learning. The students do pretest before the lesson and do post-test after the lesson by 20 items achievement tests of magnetic field. The post-test higher than pretest achievement significantly at 0.01 level. (paper)

Theory of angle-resolved photoemission from the cuprate superconductors

International Nuclear Information System (INIS)

Hedegard, P.; Pedersen, M.B.

1990-01-01

We show that the photoemission spectrum for an RVB state with bosonic spins and fermionic charges consists of a peak on top of a broad background. The 'Fermi surface' corresponds to hole pockets around certain k-vectors. The theoretical predictions are compared with the available experimental data, and with the results obtained by other approaches. (orig.)

Fingerprints of entangled spin and orbital physics in itinerant ferromagnets via angle-resolved resonant photoemission

Science.gov (United States)

Da Pieve, F.

2016-01-01

A method for mapping the local spin and orbital nature of the ground state of a system via corresponding flip excitations is proposed based on angle-resolved resonant photoemission and related diffraction patterns, obtained here via an ab initio modified one-step theory of photoemission. The analysis is done on the paradigmatic weak itinerant ferromagnet bcc Fe, whose magnetism, a correlation phenomenon given by the coexistence of localized moments and itinerant electrons, and the observed non-Fermi-Liquid behavior at extreme conditions both remain unclear. The combined analysis of energy spectra and diffraction patterns offers a mapping of local pure spin-flip, entangled spin-flip-orbital-flip excitations and chiral transitions with vortexlike wave fronts of photoelectrons, depending on the valence orbital symmetry and the direction of the local magnetic moment. Such effects, mediated by the hole polarization, make resonant photoemission a promising tool to perform a full tomography of the local magnetic properties even in itinerant ferromagnets or macroscopically nonmagnetic systems.

Surface and bulk 4f-photoemission spectra of CeIn3 and CeSn3

International Nuclear Information System (INIS)

Kim, H.; Tjernberg, O.; Chiaia, G.; Kumigashira, H.; Takahashi, T.; Duo, L.; Sakai, O.; Kasaya, M.; Lindau, I.

1997-01-01

Resonant photoemission spectroscopy was performed on CeIn 3 and CeSn 3 at the 4d-4f and 3d-4f core thresholds. Using the different surface sensitivity between the two photon energies, surface and bulk 4f-photoemission spectra were derived for both compounds. With the noncrossing approximation of the Anderson impurity model, the 4d-4f resonant spectra together with the surface and bulk spectra were self-consistently analyzed to obtain the microscopic parameters such as the 4f-electron energy and the hybridization strength with conduction electrons. The result shows a substantial difference in these parameters between the surface and the bulk, indicating that it is important to take into account the surface effect in analyzing photoemission spectra of Ce compounds. It is also found that the 4f surface core-level shift is different between CeIn 3 and CeSn 3 . copyright 1997 The American Physical Society

Rb-intercalated C{sub 60} compounds studied by Inverse Photoemission Spectroscopy

Energy Technology Data Exchange (ETDEWEB)

Finazzi, M; Brambilla, A; Biagioni, P; Cattoni, A; Duo, L; Ciccacci, F; Braicovich, L [INFM and Dip di Fisica del Politecnico di Milano, Milano (Italy); Giovanelli, L; Goldoni, A [ELETTRA Basovizza (Italy)

2004-07-01

Full text: Since the discovery of superconductivity in alkali-doped solid C{sub 60}, the electronic structure of the host material (C{sub 60}) and the doped compounds (A{sub x}C{sub 60}, where A is an alkali metal), has been the subject of a considerable amount of work, both theoretical and experimental. The spectroscopic investigations of the alkali-doped C{sub 60} compounds has been mainly focussed on the valence states, while much less information is available on the unoccupied states. In particular, inverse photoemission data on the complete set of stable Rb{sub x}C{sub 60} compounds was, so far, still missing. We have performed Inverse Photoemission (IPE) spectroscopy on Rb{sub x}C{sub 60} compounds (x = 1, 3, 4, 6). IPE spectra were obtained using a band-pass photon detector (hv = 9.4 eV, FWHM = 0.7 eV) and scanning the kinetic energy of the electrons impinging on the sample. Rb was evaporated on C{sub 60} films (thickness = 6-12 atomic layers) grown in situ on a Cu(100) substrate. The temperature of the substrate was kept equal to T = 100 deg C, which is lower than the C{sub 60} sublimation temperature. The amount of Rb was checked by measuring the intensity of the C1s and Rb3d photoemission lines. After the required amount of Rb had been deposited, the samples were annealed to distillate the desired stable phase.

Photoemission and the origin of high temperature superconductivity

International Nuclear Information System (INIS)

Norman, M. R.; Randeria, M.; Janko, B.; Campuzano, J. C.

2000-01-01

The condensation energy can be shown to be a moment of the change in the occupied part of the spectral function when going from the normal to the superconducting state. As a consequence, there is a one to one correspondence between the energy gain associated with forming the superconducting ground state, and the dramatic changes seen in angle resolved photoemission spectra. Some implications this observation has are offered

Introduction of spectroscopic photoemission and low energy electron microscope in SPring-8

International Nuclear Information System (INIS)

Guo, FangZhun; Kobayashi, Keisuke; Kinoshita, Toyohiko

2005-01-01

An upright configuration SPELEEM (Spectroscopic PhotoEmission and Low Energy Electron Microscope) has been introduced in SPring-8 in the framework of the nanotechnology support project of Ministry of Education, Culture, Sport, Science and Technology (MEXT), Japan. SPELEEM combines microscopy, spectroscopy and diffraction in one system, which allows a comprehensive characterization of the specimen. The combination of SPELEEM and polarized (circularly or linearly) soft X-rays in SPring-8 is expected to realize the highest performance. The characteristics of SPELEEM and typical results, for example nano-XANES (X-ray absorption near edge structure) of Fe oxide on Fe(100) surface, nano-XPS (X-ray photoemission spectroscopy) of indium (In) on Si(111) and antiferro-magnetic domain structure images of NiO(001) single crystal, are reported. (author)

Photoemission Spectroscopy Characterization of Attempts to Deposit MoO2 Thin Film

Directory of Open Access Journals (Sweden)

Irfan

2011-01-01

Full Text Available Attempts to deposit molybdenum dioxide (MoO2 thin films have been described. Electronic structure of films, deposited by thermal evaporation of MoO2 powder, had been investigated with ultraviolet photoemission and X-ray photoemission spectroscopy (UPS and XPS. The thermally evaporated films were found to be similar to the thermally evaporated MoO3 films at the early deposition stage. XPS analysis of MoO2 powder reveals presence of +5 and +6 oxidation states in Mo 3d core level along with +4 state. The residue of MoO2 powder indicates substantial reduction in higher oxidation states while keeping +4 oxidation state almost intact. Interface formation between chloroaluminum phthalocyanine (AlPc-Cl and the thermally evaporated film was also investigated.

Study of Si-N amorphous compounds combining XPS (X photoemission) and EELS (electron energy loss spectra) optical measurements. Internal levels photoemission. Pt. 2

International Nuclear Information System (INIS)

Guraya, M.M.; Acolani, H.; Zampieri, G.E.; Silva, J.H. Dias da; Cisneros, J.I.; Cantao, M.; Marques, F.C.

1990-01-01

A Si-N non-stoichiometric hydrogenated amorphous compounds study with different N- contents is presented. The shape and shifts of the photoemission peaks corresponding to the N - 1s and Si - 2p internal levels are analyzed. Based on the latter, the homogeneity of the samples and the Si - N bonds charge transfer is discussed. (Author) [es

Relativistic acceleration and retardation effects on photoemission of intense electron short pulses, in RF-FEL photoinjectors

International Nuclear Information System (INIS)

Dolique, J.M.; Coacolo, M.

1991-01-01

In high-power free electron lasers, self-field effects in the electron beam are often the most important phenomenon on which the beam quality depends. These effects are generally conceived as space-charge effects, and described by a Poisson equation in a beam frame. In RF-FEL photoinjectors, the electrons of the intense short pulse produced by laser irradiation are submitted, just after their photoemission, to such a strong acceleration that relativistic acceleration and retardation effects are discussed, from the rigorous calculation of the Lienard-Wiechert velocity- and acceleration electric and magnetic fields, as a function of RF-electric field and beam parameters. The beam pulse is assumed to be axisymmetric, with a constant photoemitted current density. Consequences for the maximum current density that can be extracted are considered (the 'self-field limit,' a name more appropriate than 'space-charge limit' for the present conditions where electro-dynamic phenomena play an important role)

Photoemission spectroscopy of the charge-ordering transition in Pr0.5Sr0.5MnO3

International Nuclear Information System (INIS)

Chainani, A.; Kumigashira, H.; Takahashi, T.; Tomioka, Y.; Kuwahara, H.; Tokura, Y.

1996-01-01

In this paper, the electronic structure of the magnetite Pr 0.5 Sr 0.5 MnO 3 across the charge ordering transition is studied using temperature-dependent photoemission spectroscopy. Ultra-violet photoemission spectroscopy have been performed as a function of temperature (25-300K) to investigate the changes in the single-particle density of states across the metal-nonmetal and the para-ferro transitions

Polarity effects in the x-ray photoemission of ZnO and other wurtzite semiconductors

International Nuclear Information System (INIS)

Allen, M. W.; Zemlyanov, D. Y.; Waterhouse, G. I. N.; Metson, J. B.; Veal, T. D.; McConville, C. F.; Durbin, S. M.

2011-01-01

Significant polarity-related effects were observed in the near-surface atomic composition and valence band electronic structure of ZnO single crystals, investigated by x-ray photoemission spectroscopy using both Al K α (1486.6 eV) and synchrotron radiation (150 to 1486 eV). In particular, photoemission from the lowest binding energy valence band states was found to be significantly more intense on the Zn-polar face compared to the O-polar face. This is a consistent effect that can be used as a simple, nondestructive indicator of crystallographic polarity in ZnO and other wurtzite semiconductors.

X-ray photoemission electron microscopy, a tool for the investigation of complex magnetic structures

International Nuclear Information System (INIS)

Scholl, Andreas; Ohldag, Hendrik; Nolting, Frithjof; Stohr, Joachim; Padmore, Howard A.

2001-01-01

X-ray Photoemission Electron Microscopy unites the chemical specificity and magnetic sensitivity of soft x-ray absorption techniques with the high spatial resolution of electron microscopy. The discussed instrument possesses a spatial resolution of better than 50 nm and is located at a bending magnet beamline at the Advanced Light Source, providing linearly and circularly polarized radiation between 250 and 1300 eV. We will present examples which demonstrate the power of this technique applied to problems in the field of thin film magnetism. The chemical and elemental specificity is of particular importance for the study of magnetic exchange coupling because it allows separating the signal of the different layers and interfaces in complex multi-layered structures

Photoemission spectroscopy study of a multi-alkali photocathode

CERN Document Server

Ettema, A R H

2000-01-01

In this paper a photoemission study of the highest core levels of the elements and the electron escape barrier (work function) in a multi-alkali photocathode are presented. The core levels indicate that the alkali atoms are in an oxidized state and therefore the compound Na sub 2 KSb can be regarded as an ionic semiconductor. The measured escape barrier of the Cs sub 2 O surface layer is determined as 2.3 eV.

Theory of pump–probe ultrafast photoemission and X-ray absorption spectra

Energy Technology Data Exchange (ETDEWEB)

Fujikawa, Takashi, E-mail: tfujikawa@faculty.chiba-u.jp; Niki, Kaori

2016-01-15

Highlights: • Pump–probe ultrafast XAFS and XPS spectra are theoretically studied. • Keldysh Green's function theory is applied. • Important many-body effects are explicitly included. - Abstract: Keldysh Green's function approach is extensively used in order to derive practical formulas to analyze pump–probe ultrafast photoemission and X-ray absorption spectra. Here the pump pulse is strong enough whereas the probe X-ray pulse can be treated by use of a perturbation theory. We expand full Green's function in terms of renormalized Green's function without the interaction between electrons and probe pulse. The present theoretical formulas allow us to handle the intrinsic and extrinsic losses, and furthermore resonant effects in X-ray Absorption Fine Structures (XAFS). To understand the radiation field screening in XPS spectra, we have to use more sophisticated theoretical approach. In the ultrafast XPS and XAFS analyses the intrinsic and extrinsic loss effects can interfere as well. In the XAFS studies careful analyses are necessary to handle extrinsic losses in terms of damped photoelectron propagation. The nonequilibrium dynamics after the pump pulse irradiation is well described by use of the time-dependent Dyson orbitals. Well above the edge threshold, ultrafast photoelectron diffraction and extended X-ray absorption fine structure (EXAFS) provide us with transient structural change after the laser pump excitations. In addition to these slow processes, the rapid oscillation in time plays an important role related to pump electronic excitations. Near threshold detailed information could be obtained for the combined electronic and structural dynamics. In particular high-energy photoemission and EXAFS are not so influenced by the details of excited states by pump pulse. Random-Phase Approximation (RPA)-boson approach is introduced to derive some practical formulas for time-dependent intrinsic amplitudes.

Photoemission investigation of the ZnSe/CdTe heterojunction band discontinuity

International Nuclear Information System (INIS)

Nelson, A.J.

1995-01-01

Synchrotron radiation soft x-ray photoemission spectroscopy and reflection high-energy electron diffraction were used to investigate the structural and electronic properties at the ZnSe/CdTe(100) heterojunction interface. ZnSe overlayers were sequentially grown in steps on p-type CdTe(100) single crystals at 200 degree C. In situ photoemission measurements were acquired after each growth in order to observe changes in the valence band electronic structure as well as changes in the Cd 4d, Zn 3d, and Te 4d core lines. The results were used to correlate the interfacial chemistry with the electronic structure and to directly determine the ZnSe/CdTe heterojunction valence band discontinuity and the consequent heterojunction band diagram. Results of these measurements reveal that the valence band offset is ΔE v =0.20 eV. copyright 1995 American Institute of Physics

X-ray photoemission study of plutonium metal

International Nuclear Information System (INIS)

Baptist, R.

1982-01-01

The x-ray induced photoemission from clean pure plutonium metal is described and the results for both core and valence levels are compared with previous measurements on light actinides. It is found that, as in thorium and urnaium, the configuration interaction plays an important role for core levels, in particular for those of the n=5 shell. The experimental valence-band spectrum confirms the existence of 5f states at the Fermi level and is compared with a density of states of FCC Pu derived from a recent relativistic band structure calculation. (author)

Hartmann characterization of the PEEM-3 aberration-corrected X-ray photoemission electron microscope.

Science.gov (United States)

Scholl, A; Marcus, M A; Doran, A; Nasiatka, J R; Young, A T; MacDowell, A A; Streubel, R; Kent, N; Feng, J; Wan, W; Padmore, H A

2018-05-01

Aberration correction by an electron mirror dramatically improves the spatial resolution and transmission of photoemission electron microscopes. We will review the performance of the recently installed aberration corrector of the X-ray Photoemission Electron Microscope PEEM-3 and show a large improvement in the efficiency of the electron optics. Hartmann testing is introduced as a quantitative method to measure the geometrical aberrations of a cathode lens electron microscope. We find that aberration correction leads to an order of magnitude reduction of the spherical aberrations, suggesting that a spatial resolution of below 100 nm is possible at 100% transmission of the optics when using x-rays. We demonstrate this improved performance by imaging test patterns employing element and magnetic contrast. Published by Elsevier B.V.

Ultraviolet photoemission spectroscopy of hydrogen complex deactivation on InP:Zn(1 0 0) surfaces

International Nuclear Information System (INIS)

Williams, M.D.; Williams, S.C.; Yasharahla, S.A.; Jallow, N.

2007-01-01

Ultraviolet photoemission spectroscopy is used to study the kinetics of the H-Zn complex deactivation in Zn doped InP(1 0 0). Hydrogen injected into the material electronically passivates the local carrier concentration. Reverse-biased anneals of the InP under ultra-high vacuum show a dramatic change in the work function of the material with increasing temperature. Spectral features are also shown to be sensitive to sample temperature. To our knowledge, we show the first view of hydrogen retrapping at the surface using photoemission spectroscopy. A simple photoelectron threshold energy analysis shows the state of charge compensation of the material

Optimisation of applied field pulses for microwave assisted magnetic recording

Directory of Open Access Journals (Sweden)

Simon John Greaves

2017-05-01

Full Text Available Grains in a recording medium experience field pulses from a write head during recording. In general, a short head field rise time and a square pulse shape have been viewed as optimal. This work investigates the optimum field pulse shape for microwave assisted magnetic recording on single layer and ECC media. A square pulse was found to give the best recording performance on single layer media, but an initially negative field pulse increasing at a constant rate was more suitable for ECC media.

High resolution hard X-ray photoemission using synchrotron radiation as an essential tool for characterization of thin solid films

International Nuclear Information System (INIS)

Kim, J.J.; Ikenaga, E.; Kobata, M.; Takeuchi, A.; Awaji, M.; Makino, H.; Chen, P.P.; Yamamoto, A.; Matsuoka, T.; Miwa, D.; Nishino, Y.; Yamamoto, T.; Yao, T.; Kobayashi, K.

2006-01-01

Recently, we have shown that hard X-ray photoemission spectroscopy using undulator X-rays at SPring-8 is quite feasible with both high resolution and high throughput. Here we report an application of hard X-ray photoemission spectroscopy to the characterization of electronic and chemical states of thin solid films, for which conventional PES is not applicable. As a typical example, we focus on the problem of the scatter in the reported band-gap values for InN. We show that oxygen incorporation into the InN film strongly modifies the valence and plays a crucial role in the band gap problem. The present results demonstrate the powerful applicability of high resolution photoemission spectroscopy with hard X-rays from a synchrotron source

Fingerprints of spin-orbital polarons and of their disorder in the photoemission spectra of doped Mott insulators with orbital degeneracy

Science.gov (United States)

Avella, Adolfo; Oleś, Andrzej M.; Horsch, Peter

2018-04-01

means of a complementary many-body polaron theory, which yields a similar robust spin and orbital order as the Hartree-Fock approximation. Using realistic parameters for the vanadium perovskite La1 -xCaxVO3 , we show that its soft gap is reproduced as well as the marginal doping dependence of the position of the chemical potential relative to the center of the lower Hubbard band. The present theory uncovers also the reasons why the d1→d0 satellite excitations, which directly probe the effect of the random defect fields on the polaron state, are not well resolved in the available experimental photoemission spectra for La1 -xCaxVO3 .

Photoemission and the electronic properties of heavy fermions -- limitations of the Kondo model

International Nuclear Information System (INIS)

Joyce, J.J.; Arko, A.J.; Andrews, A.B.

1993-01-01

The electronic properties of Yb-based heavy fermions have been investigated by means of high resolution synchrotron radiation photoemission and compared with predictions of the Kondo model. The Yb heavy fermion photoemission spectra show massive disagreement with the Kondo model predictions (as calculated within the Gunnarsson-Schonhammer computational method). Moreover, the Yb heavy fermion photoemission spectra give very strong indications of core-like characteristics and compare favorable to purely divalent Yb metal and core-like Lu 4f levels. The heavy fermions YbCu 2 Si 2 , YbAgCu 4 and YbAl 3 were measured and shown to have lineshapes much broader and deeper in binding energy than predicted by the Kondo model. The lineshape of the bulk component of the 4f emission for these three heavy fermion materials was compared with that from Yb metal and the Lu 4f levels in LuAl 3 , the heavy fermion materials show no substantive spectroscopic differences from simple 4f levels observed in Yb metal and LuAl 3 . Also, the variation with temperature of the 4f fineshape was measured for Yb metal and clearly demonstrates that phonon broadening plays a major role in 4f level lineshape analysis and must be accounted for before considerations of correlated electron resonance effects are presumed to be at work

Review of the theoretical description of time-resolved angle-resolved photoemission spectroscopy in electron-phonon mediated superconductors

Energy Technology Data Exchange (ETDEWEB)

Kemper, A.F. [Department of Physics, North Carolina State University, Raleigh, NC (United States); Sentef, M.A. [Max Planck Institute for the Structure and Dynamics of Matter, Center for Free Electron Laser Science, Hamburg (Germany); Moritz, B. [Stanford Institute for Materials and Energy Sciences (SIMES), SLAC National Accelerator Laboratory, Menlo Park, CA (United States); Devereaux, T.P. [Stanford Institute for Materials and Energy Sciences (SIMES), SLAC National Accelerator Laboratory, Menlo Park, CA (United States); Geballe Laboratory for Advanced Materials, Stanford University, Stanford, CA (United States); Freericks, J.K. [Department of Physics, Georgetown University, Washington, DC (United States)

2017-09-15

We review recent work on the theory for pump/probe photoemission spectroscopy of electron-phonon mediated superconductors in both the normal and the superconducting states. We describe the formal developments that allow one to solve the Migdal-Eliashberg theory in nonequilibrium for an ultrashort laser pumping field, and explore the solutions which illustrate the relaxation as energy is transferred from electrons to phonons. We focus on exact results emanating from sum rules and approximate numerical results which describe rules of thumb for relaxation processes. In addition, in the superconducting state, we describe how Anderson-Higgs oscillations can be excited due to the nonlinear coupling with the electric field and describe mechanisms where pumping the system enhances superconductivity. (copyright 2017 by WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

Magnetic dichroism in UV photoemission at off-normal emission: Study of the valence bands

International Nuclear Information System (INIS)

Venus, D.; Kuch, W.; Lin, M.; Schneider, C.M.; Ebert, H.; Kirschner, J.

1997-01-01

Magnetic dichroism of angle-resolved UV photoemission from fcc Co/Cu(001) thin films has been measured using linearly p-polarized light, and a coplanar geometry where the light and photoelectron wave vectors are antiparallel, and both are perpendicular to the in-plane sample magnetization. This geometry emphasizes information about state dispersion due to the crystalline symmetry. An orderly dispersion of the features in the magnetic dichroism over a wide range of off-normal angles of electron emission is related in detail to the bulk band structure of fcc Co. The measurements confirm the practical utility of magnetic dichroism experiments as a relatively simple complement to spin-resolved photoemission. copyright 1997 The American Physical Society

Principle and application of low energy inverse photoemission spectroscopy: A new method for measuring unoccupied states of organic semiconductors

Energy Technology Data Exchange (ETDEWEB)

Yoshida, Hiroyuki, E-mail: hyoshida@chiba-u.jp

2015-10-01

Highlights: • Principle of low energy inverse photoemission spectroscopy is described. • Instruments including electron sources and photon detectors are shown. • Recent results about organic devices and fundamental studies are reviewed. • Electron affinities of typical organic semiconductors are compiled. - Abstract: Information about the unoccupied states is crucial to both fundamental and applied physics of organic semiconductors. However, there were no available experimental methods that meet the requirement of such research. In this review, we describe a new experimental method to examine the unoccupied states, called low-energy inverse photoemission spectroscopy (LEIPS). An electron having the kinetic energy lower than the damage threshold of organic molecules is introduced to a sample film, and an emitted photon in the near-ultraviolet range is detected with high resolution and sensitivity. Unlike the previous inverse photoemission spectroscopy, the sample damage is negligible and the overall resolution is a factor of two improved to 0.25 eV. Using LEIPS, electron affinity of organic semiconductor can be determined with the same precision as photoemission spectroscopy for ionization energy. The instruments including an electron source and photon detectors as well as application to organic semiconductors are presented.

Principle and application of low energy inverse photoemission spectroscopy: A new method for measuring unoccupied states of organic semiconductors

International Nuclear Information System (INIS)

Yoshida, Hiroyuki

2015-01-01

Highlights: • Principle of low energy inverse photoemission spectroscopy is described. • Instruments including electron sources and photon detectors are shown. • Recent results about organic devices and fundamental studies are reviewed. • Electron affinities of typical organic semiconductors are compiled. - Abstract: Information about the unoccupied states is crucial to both fundamental and applied physics of organic semiconductors. However, there were no available experimental methods that meet the requirement of such research. In this review, we describe a new experimental method to examine the unoccupied states, called low-energy inverse photoemission spectroscopy (LEIPS). An electron having the kinetic energy lower than the damage threshold of organic molecules is introduced to a sample film, and an emitted photon in the near-ultraviolet range is detected with high resolution and sensitivity. Unlike the previous inverse photoemission spectroscopy, the sample damage is negligible and the overall resolution is a factor of two improved to 0.25 eV. Using LEIPS, electron affinity of organic semiconductor can be determined with the same precision as photoemission spectroscopy for ionization energy. The instruments including an electron source and photon detectors as well as application to organic semiconductors are presented.

Multiplet splitting of x-ray photoemission spectra core levels in magnetic metals

International Nuclear Information System (INIS)

Kowalczyk, S.P.; McFeely, F.R.; Ley, L.; Shirley, D.A.

1975-01-01

The results of high resolution x-ray photoemission studies of the multiplet splitting of the 3s core levels in the 3d transition metals and the 4s, 5s and 4d core levels in the lanthanide metals are reported

Resonant photoemission of La and Yb at the 3d absorption edge

CERN Document Server

Lagarde, P; Ogasawara, H; Kotani, A

2003-01-01

Resonant photoemission and resonant Auger experiments at the 3d threshold are presented for La and Yb over a binding energy domain which extends up to the 4p levels. These experimental results are well explained by calculations in the framework of full-multiplet Hartree-Fock theory with an atomic model. Strong participator and spectator Auger transitions are observed without ordinary Auger transition, indicating that the 4f wavefunction is well localized in the intermediate state even in the case of La. The 4d sub 3 sub / sub 2 and 4d sub 5 sub / sub 2 branching ratio of the 4d resonant photoemission of La at the M sub 4 and M sub 5 edges is observed experimentally and analyzed theoretically. The difference in the resonant processes behavior for La and Yb is discussed based upon the different 4f occupation number.

Enhanced photoemission from laser-excited plasmonic nano-objects in periodic arrays

Czech Academy of Sciences Publication Activity Database

Fedorov, N.; Geoffroy, G.; Duchateau, G.; Štolcová, L.; Proška, J.; Novotný, F.; Domonkos, Mária; Jouin, H.; Martin, P.; Raynaud, M.

2016-01-01

Roč. 28, č. 31 (2016), s. 1-15, č. článku 315301. ISSN 0953-8984 R&D Projects: GA ČR(CZ) GBP108/12/G108 Institutional support: RVO:68378271 Keywords : photoemission * laser excitation * surface plasmon * plasmonics Subject RIV: BH - Optics, Masers, Lasers Impact factor: 2.649, year: 2016

Enhanced performance of thermal-assisted electron field emission based on barium oxide nanowire

Energy Technology Data Exchange (ETDEWEB)

Cui, Yunkang [Department of Mathematics and Physics, Nanjing Institute of technology, Nanjing, 211167 (China); Chen, Jing, E-mail: chenjingmoon@gmail.com [School of Electronic Science & Engineering, Southeast University, Nanjing, 210096 (China); Zhang, Yuning; Zhang, Xiaobing; Lei, Wei; Di, Yunsong [School of Electronic Science & Engineering, Southeast University, Nanjing, 210096 (China); Zhang, Zichen, E-mail: zz241@ime.ac.cn [Integrated system for Laser applications Group, Institute of Microelectronics of Chinese Academy of Sciences, 100029, Beijing (China)

2017-02-28

Highlights: • A possible mechanism for thermal-assisted electric field was demonstrated. • A new path for the architecture of the novel nanomaterial and methodology for its potential application in the field emission device area was provided. • The turn-on field, the threshold field and the field emission current density were largely related to the temperature of the cathode. • The relationship between the work function of emitter material and the temperature of emitter was found. - Abstract: In this paper, thermal-assisted field emission properties of barium oxide (BaO) nanowire synthesized by a chemical bath deposition method were investigated. The morphology and composition of BaO nanowire were characterized by field emission scanning electron microscopy (FESEM), high resolution transmission electron microscopy (HRTEM), selected area electron diffraction (SED), X-ray diffraction (XRD), and energy dispersive X-ray spectrometer (EDX) respectively. The turn-on field, threshold field and the emission current density could be affected relatively due to the thermal-assisted effect when the electric field was applied, in the meanwhile, the turn-on field for BaO nanowire was measured to be decreased from 1.12 V/μm to 0.66 V/μm when the temperature was raised from 293 K to 593 K, whereas for the threshold field was found to decrease from 3.64 V/μm to 2.12 V/μm. The improved performance was demonstrated due to the reduced work function of the BaO nanowire as the agitation temperature increasing, leading to the higher probability of electrons tunneling through the energy barrier and enhancement of the field emission properties of BaO emitters.

Enhanced performance of thermal-assisted electron field emission based on barium oxide nanowire

International Nuclear Information System (INIS)

Cui, Yunkang; Chen, Jing; Zhang, Yuning; Zhang, Xiaobing; Lei, Wei; Di, Yunsong; Zhang, Zichen

2017-01-01

Highlights: • A possible mechanism for thermal-assisted electric field was demonstrated. • A new path for the architecture of the novel nanomaterial and methodology for its potential application in the field emission device area was provided. • The turn-on field, the threshold field and the field emission current density were largely related to the temperature of the cathode. • The relationship between the work function of emitter material and the temperature of emitter was found. - Abstract: In this paper, thermal-assisted field emission properties of barium oxide (BaO) nanowire synthesized by a chemical bath deposition method were investigated. The morphology and composition of BaO nanowire were characterized by field emission scanning electron microscopy (FESEM), high resolution transmission electron microscopy (HRTEM), selected area electron diffraction (SED), X-ray diffraction (XRD), and energy dispersive X-ray spectrometer (EDX) respectively. The turn-on field, threshold field and the emission current density could be affected relatively due to the thermal-assisted effect when the electric field was applied, in the meanwhile, the turn-on field for BaO nanowire was measured to be decreased from 1.12 V/μm to 0.66 V/μm when the temperature was raised from 293 K to 593 K, whereas for the threshold field was found to decrease from 3.64 V/μm to 2.12 V/μm. The improved performance was demonstrated due to the reduced work function of the BaO nanowire as the agitation temperature increasing, leading to the higher probability of electrons tunneling through the energy barrier and enhancement of the field emission properties of BaO emitters.

Electrospray deposition of fullerenes in ultra-high vacuum: in situ scanning tunneling microscopy and photoemission spectroscopy

International Nuclear Information System (INIS)

Satterley, Christopher J; Perdigao, LuIs M A; Saywell, Alex; Magnano, Graziano; Rienzo, Anna; Mayor, Louise C; Dhanak, Vinod R; Beton, Peter H; O'Shea, James N

2007-01-01

Electrospray deposition of fullerenes on gold has been successfully observed by in situ room temperature scanning tunneling microscopy and photoemission spectroscopy. Step-edge decoration and hexagonal close-packed islands with a periodicity of 1 nm are observed at low and multilayer coverages respectively, in agreement with thermal evaporation studies. Photoemission spectroscopy shows that fullerenes are being deposited in high purity and are coupling to the gold surface as for thermal evaporation. These results open a new route for the deposition of thermally labile molecules under ultra-high vacuum conditions for a range of high resolution surface science techniques

Development of high-energy resolution inverse photoemission technique

International Nuclear Information System (INIS)

Asakura, D.; Fujii, Y.; Mizokawa, T.

2005-01-01

We developed a new inverse photoemission (IPES) machine based on a new idea to improve the energy resolution: off-plane Eagle mounting of the optical system in combination with dispersion matching between incoming electron and outgoing photon. In order to achieve dispersion matching, we have employed a parallel plate electron source and have investigated whether the electron beam is obtained as expected. In this paper, we present the principle and design of the new IPES method and report the current status of the high-energy resolution IPES machine

Influence of trap-assisted tunneling on trap-assisted tunneling current in double gate tunnel field-effect transistor

International Nuclear Information System (INIS)

Jiang Zhi; Zhuang Yi-Qi; Li Cong; Wang Ping; Liu Yu-Qi

2016-01-01

Trap-assisted tunneling (TAT) has attracted more and more attention, because it seriously affects the sub-threshold characteristic of tunnel field-effect transistor (TFET). In this paper, we assess subthreshold performance of double gate TFET (DG-TFET) through a band-to-band tunneling (BTBT) model, including phonon-assisted scattering and acoustic surface phonons scattering. Interface state density profile (D it ) and the trap level are included in the simulation to analyze their effects on TAT current and the mechanism of gate leakage current. (paper)

The Fermi surface and band folding in La{sub 2-x}Sr{sub x}CuO{sub 4}, probed by angle-resolved photoemission

Energy Technology Data Exchange (ETDEWEB)

Razzoli, E; Radovic, M; Patthey, L; Shi, M [Swiss Light Source, Paul Scherrer Institut, CH-5232 Villigen PSI (Switzerland); Sassa, Y; Chang, J [Laboratory for Neutron Scattering, Paul Scherrer Institut, CH-5232 Villigen PSI (Switzerland); Drachuck, G; Keren, A; Shay, M [Department of Physics, Technion-Israel Institute of Technology, Haifa 32000 (Israel); Maansson, M; Mesot, J [Laboratory for Synchrotron and Neutron Spectroscopy, EPF Lausanne, CH-1015 Lausanne (Switzerland); Berntsen, M H; Tjernberg, O [Materials Physics, KTH Royal Institute of Technology, S-16440 Kista (Sweden); Pailhes, S [CEA, CNRS, CE Saclay, Laboratoire Leon Brillouin, F-91191 Gif Sur Yvette (France); Momono, N [Department of Applied Sciences, Muroran Institute of Technology, Muroran 050-8585 (Japan); Oda, M; Ido, M [Department of Physics, Hokkaido University, Sapporo 060-0810 (Japan); Lipscombe, O J; Hayden, S M, E-mail: ming.shi@psi.c [H H Wills Physics Laboratory, University of Bristol, Tyndall Avenue, Bristol BS8 1TL (United Kingdom)

2010-12-15

A systematic angle-resolved photoemission study of the electronic structure of La{sub 2-x}Sr{sub x}CuO{sub 4} in a wide doping range is presented in this paper. In addition to the main energy band, we observed a weaker additional band, the ({pi}, {pi}) folded band, which shows unusual doping dependence. The appearance of the folded band suggests that a Fermi surface reconstruction is doping dependent and could already occur at zero magnetic field.

The dynamics of coupled atom and field assisted by continuous external pumping

International Nuclear Information System (INIS)

Burlak, G.; Hernandez, J.A.; Starostenko, O.

2006-01-01

The dynamics of a coupled system comprising a two-level atom and cavity field assisted by a continuous external classical field (driving Jaynes-Cummings model) is studied. When the initial field is prepared in a coherent state, the dynamics strongly depends on the algebraic sum of both fields. If this sum is zero (the compensative case) in the system, only the vacuum Rabi oscillations occur. The results with dissipation and external field detuning from the cavity field are also discussed. (Author)

The dynamics of coupled atom and field assisted by continuous external pumping

Energy Technology Data Exchange (ETDEWEB)

Burlak, G.; Hernandez, J.A. [Centro de Investigacion en Ingenieria y Ciencias Aplicadas, Universidad Autonoma de Morelos, Cuernavaca, Morelos (Mexico); Starostenko, O. [Departamento de Fisica, Electronica, Sistemas y Mecatronica, Universidad de las Americas, 72820 Puebla (Mexico)

2006-07-01

The dynamics of a coupled system comprising a two-level atom and cavity field assisted by a continuous external classical field (driving Jaynes-Cummings model) is studied. When the initial field is prepared in a coherent state, the dynamics strongly depends on the algebraic sum of both fields. If this sum is zero (the compensative case) in the system, only the vacuum Rabi oscillations occur. The results with dissipation and external field detuning from the cavity field are also discussed. (Author)

Electronic structure of Mo1-x Re x alloys studied through resonant photoemission spectroscopy

Science.gov (United States)

Sundar, Shyam; Banik, Soma; Sharath Chandra, L. S.; Chattopadhyay, M. K.; Ganguli, Tapas; Lodha, G. S.; Pandey, Sudhir K.; Phase, D. M.; Roy, S. B.

2016-08-01

We studied the electronic structure of Mo-rich Mo1-x Re x alloys (0≤slant x≤slant 0.4 ) using valence band photoemission spectroscopy in the photon energy range 23-70 eV and density of states calculations. Comparison of the photoemission spectra with the density of states calculations suggests that, with respect to the Fermi level E F, the d states lie mostly in the binding energy range 0 to  -6 eV, whereas s states lie in the binding energy range  -4 to  -10 eV. We observed two resonances in the photoemission spectra of each sample, one at about 35 eV photon energy and the other at about 45 eV photon energy. Our analysis suggests that the resonance at 35 eV photon energy is related to the Mo 4p-5s transition and the resonance at 45 eV photon energy is related to the contribution from both the Mo 4p-4d transition (threshold: 42 eV) and the Re 5p-5d transition (threshold: 46 eV). In the constant initial state plot, the resonance at 35 eV incident photon energy for binding energy features in the range E F (BE  =  0) to  -5 eV becomes progressively less prominent with increasing Re concentration x and vanishes for x  >  0.2. The difference plots obtained by subtracting the valence band photoemission spectrum of Mo from that of Mo1-x Re x alloys, measured at 47 eV photon energy, reveal that the Re d-like states appear near E F when Re is alloyed with Mo. These results indicate that interband s-d interaction, which is weak in Mo, increases with increasing x and influences the nature of the superconductivity in alloys with higher x.

Modeling of Diamond Field-Emitter-Arrays for high brightness photocathode applications

Science.gov (United States)

Kwan, Thomas; Huang, Chengkun; Piryatinski, Andrei; Lewellen, John; Nichols, Kimberly; Choi, Bo; Pavlenko, Vitaly; Shchegolkov, Dmitry; Nguyen, Dinh; Andrews, Heather; Simakov, Evgenya

2017-10-01

We propose to employ Diamond Field-Emitter-Arrays (DFEAs) as high-current-density ultra-low-emittance photocathodes for compact laser-driven dielectric accelerators capable of generating ultra-high brightness electron beams for advanced applications. We develop a semi-classical Monte-Carlo photoemission model for DFEAs that includes carriers' transport to the emitter surface and tunneling through the surface under external fields. The model accounts for the electronic structure size quantization affecting the transport and tunneling process within the sharp diamond tips. We compare this first principle model with other field emission models, such as the Child-Langmuir and Murphy-Good models. By further including effects of carrier photoexcitation, we perform simulations of the DFEAs' photoemission quantum yield and the emitted electron beam. Details of the theoretical model and validation against preliminary experimental data will be presented. Work ssupported by LDRD program at LANL.

Robot-assisted biopsies in a high-field MRI system. First clinical results

International Nuclear Information System (INIS)

Schell, B.; Eichler, K.; Mack, M.G.; Mueller, C.; Kerl, J.M.; Beeres, M.; Thalhammer, A.; Vogl, T.J.; Zangos, S.; Czerny, C.

2012-01-01

Purpose: The purpose of this study was to examine the clinical use of MR-guided biopsies in patients with suspicious lesions using a new MR-compatible assistance system in a high-field MR system. Materials and Methods: Six patients with suspicious focal lesions in various anatomic regions underwent percutanous biopsy in a high-field MR system (1.5 T, Magnetom Espree, Siemens) using a new MR-compatible assistance system (Innomotion). The procedures were planned and guided using T1-weighted FLASH and TrueFISP sequences. A servopneumatic drive then moved the guiding arm automatically to the insertion point. An MRI compatible 15G biopsy system (Somatex) was introduced by a physician guided by the needle holder and multiple biopsies were performed using the coaxial technique. The feasibility, duration of the intervention and biopsy findings were analyzed. Results: The proposed new system allows accurate punctures in a high-field MR system. The assistance device did not interfere with the image quality, and guided the needle virtually exactly as planned. Histological examination could be conducted on every patient. The lesion was malignant in four cases, and an infectious etiology was diagnosed for the two remaining lesions. Regarding the differentiation of anatomical and pathological structures and position monitoring of the insertion needle, TrueFISP images are to be given preference. The average intervention time was 41 minutes. Lesions up to 15.4 cm beneath the skin surface were punctured. Conclusion: The proposed MR-guided assistance system can be successfully utilized in a high-field MR system for accurate punctures of even deep lesions in various anatomic regions. (orig.)

Core and valence level photoemission and photoabsorption study of icosahedral Al-Pd-Mn quasicrystals

International Nuclear Information System (INIS)

Horn, K; Theis, W; Paggel, J J; Barman, S R; Rotenberg, E; Ebert, Ph; Urban, K

2006-01-01

The electronic structure of quasicrystalline Al-Pd-Mn is investigated by means of valence and core level photoelectron spectroscopy. Variations of the photoionization cross section in the constituents' valence electronic levels as a function of photon energy are used to identify contributions from the different atomic species, in particular near the Pd 4d Cooper minimum. Resonant photoemission at the Mn 2p absorption edge shows the contribution of the Mn 3d states to the density of states in a region near the Fermi level. The asymmetry of Pd 3d and Mn 2p core level photoemission lines, and its difference for emission from metallic and quasicrystalline phases, are utilized to infer the contributions of the different constituents to the density of states at the Fermi level

Calculation of fluctuations and photoemission properties in a tetrahedral-cluster model for an intermediate-valence system

International Nuclear Information System (INIS)

Reich, A.; Falicov, L.M.

1986-01-01

An exact solution of a four-site tetrahedral-crystal model, the smallest face-centered-cubic crystal, is presented in the case of an intermediate-valence system. The model consists of the following: (a) one extended orbital and one localized orbital per atom, (b) an interatomic transfer term between extended orbitals, (c) an interatomic hybridization between the localized and extended orbitals, (d) strong intra-atomic Coulomb repulsion between opposite-spin localized states, and (e) intermediate-strength intra-atomic Coulomb repulsion between the localized and extended states. These competing effects are examined as they manifest themselves in the intermediate-valence, photoemission, inverse-photoemission, and thermodynamic properties

Characterizing the effects of regolith surface roughness on photoemission from surfaces in space

Science.gov (United States)

Dove, A.; Horanyi, M.; Wang, X.

2017-12-01

Surfaces of airless bodies and spacecraft in space are exposed to a variety of charging environments. A balance of currents due to plasma bombardment, photoemission, electron and ion emission and collection, and secondary electron emission determines the surface's charge. Photoelectron emission is the dominant charging process on sunlit surfaces in the inner solar system due to the intense solar UV radiation. This can result in a net positive surface potential, with a cloud of photoelectrons immediately above the surface, called the photoelectron sheath. Conversely, the unlit side of the body will charge negatively due the collection of the fast-moving solar wind electrons. The interaction of charged dust grains with these positively and negatively charged surfaces, and within the photoelectron and plasma sheaths may explain the occurrence of dust lofting, levitation and transport above the lunar surface. The surface potential of exposed objects is also dependent on the material properties of their surfaces. Composition and particle size primarily affect the quantum efficiency of photoelectron generation; however, surface roughness can also control the charging process. In order to characterize these effects, we have conducted laboratory experiments to examine the role of surface roughness in generating photoelectrons in dedicated laboratory experiments using solid and dusty surfaces of the same composition (CeO2), and initial comparisons with JSC-1 lunar simulant. Using Langmuir probe measurements, we explore the measured potentials above insulating surfaces exposed to UV and an electric field, and we show that the photoemission current from a dusty surface is largely reduced due to its higher surface roughness, which causes a significant fraction of the emitted photoelectrons to be re-absorbed within the surface. We will discuss these results in context of similar situations on planetary surfaces.

Electronic structure investigation of atomic layer deposition ruthenium(oxide) thin films using photoemission spectroscopy

Science.gov (United States)

Schaefer, Michael; Schlaf, Rudy

2015-08-01

Analyzing and manipulating the electronic band line-up of interfaces in novel micro- and nanoelectronic devices is important to achieve further advancement in this field. Such band alignment modifications can be achieved by introducing thin conformal interfacial dipole layers. Atomic layer deposition (ALD), enabling angstrom-precise control over thin film thickness, is an ideal technique for this challenge. Ruthenium (Ru0) and its oxide (RuO2) have gained interest in the past decade as interfacial dipole layers because of their favorable properties like metal-equivalent work functions, conductivity, etc. In this study, initial results of the electronic structure investigation of ALD Ru0 and RuO2 films via photoemission spectroscopy are presented. These experiments give insight into the band alignment, growth behavior, surface structure termination, and dipole formation. The experiments were performed in an integrated vacuum system attached to a home-built, stop-flow type ALD reactor without exposing the samples to the ambient in between deposition and analysis. Bis(ethylcyclopentadienyl)ruthenium(II) was used as precursor and oxygen as reactant. The analysis chamber was outfitted with X-ray photoemission spectroscopy (LIXPS, XPS). The determined growth modes are consistent with a strong growth inhibition situation with a maximum average growth rate of 0.21 Å/cycle for RuO2 and 0.04 Å/cycle for Ru.0 An interface dipole of up to -0.93 eV was observed, supporting the assumption of a strongly physisorbed interface. A separate experiment where the surface of a RuO film was sputtered suggests that the surface is terminated by an intermediate, stable, non-stoichiometric RuO2/OH compound whose surface is saturated with hydroxyl groups.

X-ray photoemission electron microscopy for the study of semiconductor materials

International Nuclear Information System (INIS)

Anders, Simone; Stammler, Thomas; Padmore, Howard A.; Terminello, Louis J.; Jankowski, Alan F.; Stoehr, Joachim; Diaz, Javier; Cossy-Favre, Aline; Singh, Sangeet

1998-01-01

Photoemission Electron Microscopy using X-rays (X-PEEM) is a novel combination of two established materials analysis techniques--PEEM using UV light, and Near Edge X-ray Absorption Fine Structure (NEXAFS) spectroscopy. This combination allows the study of elemental composition and bonding structure of the sample by NEXAFS spectroscopy with a high spatial resolution given by the microscope. A simple, two lens, 10 kV operation voltage PEEM has been used at the Stanford Synchrotron Radiation Laboratory and at the Advanced Light Source (ALS) in Berkeley to study various problems including materials of interest for the semiconductor industry. In the present paper we give a short overview over the method and the instrument which was used, and describe in detail a number of applications. These applications include the study of the different phases of titanium disilicide, various phases of boron nitride, and the analysis of small particles. A brief outlook is given on possible new fields of application of the PEEM technique, and the development of new PEEM instruments

A WebGIS-Based Teaching Assistant System for Geography Field Practice (TASGFP)

Science.gov (United States)

Wang, Jiechen; Ni, Haochen; Rui, Yikang; Cui, Can; Cheng, Liang

2016-01-01

Field practice is an important part of training geography research talents. However, traditional teaching methods may not adequately manage, share and implement instruction resources and thus may limit the instructor's ability to conduct field instruction. A possible answer is found in the rapid development of computer-assisted instruction (CAI),…

Influence of trap-assisted tunneling on trap-assisted tunneling current in double gate tunnel field-effect transistor

Science.gov (United States)

Zhi, Jiang; Yi-Qi, Zhuang; Cong, Li; Ping, Wang; Yu-Qi, Liu

2016-02-01

Trap-assisted tunneling (TAT) has attracted more and more attention, because it seriously affects the sub-threshold characteristic of tunnel field-effect transistor (TFET). In this paper, we assess subthreshold performance of double gate TFET (DG-TFET) through a band-to-band tunneling (BTBT) model, including phonon-assisted scattering and acoustic surface phonons scattering. Interface state density profile (Dit) and the trap level are included in the simulation to analyze their effects on TAT current and the mechanism of gate leakage current. Project supported by the National Natural Science Foundation of China (Grant Nos. 61574109 and 61204092).

Gas-phase photoemission with soft x-rays: cross sections and angular distributions

International Nuclear Information System (INIS)

Shirley, D.A.; Kobrin, P.H.; Truesdale, C.M.; Lindle, D.W.; Ferrett, T.A.; Heimann, P.A.; Becker, U.; Kerkhoff, H.G.; Southworth, S.H.

1983-09-01

A summary is presented of typical gas-phase photoemission studies based on synchrotron radiation in the 50-5000 eV range, using beam lines at the Stanford Synchrotron Radiation Laboratory. Three topics are addressed: atomic inner-shell photoelectron cross sections and asymmetries, correlation peaks in rare gases, and core-level shape resonances in molecules

Hot Electron Photoemission from Plasmonic Nanoparticles: Role of Transient Absorption in Surface Mechanism

DEFF Research Database (Denmark)

Uskov, Alexander V.; Protsenko, Igor E.; Ikhsanov, Renat S.

2014-01-01

We analyze and compare surface- and vol ume-based internal photoelectric effects from spherical nanoparticles, obtaining analytical expression s for the photoemission rate in both cases. Similar to results for a flat metal surface, one can show that the surface mechanism preva ils, since it is un...

Electronic properties of Nd2−xCexCuO4+δ: A hard X-ray photoemission investigation

International Nuclear Information System (INIS)

Guarino, A.; Panaccione, G.; Offi, F.; Monaco, G.; Fondacaro, A.; Torelli, P.; Fittipaldi, R.; Vecchione, A.; Pace, S.; Nigro, A.

2016-01-01

Highlights: • We grow and characterize Nd 2−x Ce x CuO 4+δ samples as thin film and single crystal. • We study the Cu 2p levels of our samples by hard X-ray photoemission spectroscopy. • We investigate bulk features of the Nd 2−x Ce x CuO 4+δ samples. • Signature of the bulk response is correlated with the crystallinity of the samples. - Abstract: Cu 2p core levels spectra measured by X-ray photoemission spectroscopy of selected as-grown Nd 2−x Ce x CuO 4+δ samples are presented and discussed. The presence of a satellite peak in the 2p core level of Nd 2−x Ce x CuO 4+δ single crystal by hard X-ray photoemission is confirmed in all non-superconducting samples, films and single crystals investigated in this work. The comparison of the spectral features of the different samples suggests that the presence and the intensity of this satellite peak is not related to the electric transport properties, but to the texture characteristics.

Pseudogap behavior of RuP probed by photoemission spectroscopy

OpenAIRE

Sato, K.; Ootsuki, D.; Wakisaka, Y.; Saini, N. L.; Mizokawa, T.; Arita, M.; Anzai, H.; Namatame, H.; Taniguchi, M.; Hirai, D.; Takagi, H.

2012-01-01

We have studied the electronic structure of RuP and related Ru pnictides using photoemission spectroscopy. Ru 3d core-level and valence-band spectra of RuP show that the Ru valence is +3 with t_{2g}^5 configuration. The photoemisson spectral weight near the Fermi level is moderately suppressed in the pseudogap phase of RuP, consistent with the pseudogap opening of 2\\Delta/k_BT_c ~ 3 (gap size \\Delta ~ 50 meV and transition temperature T_c ~ 330 K). The Ru 3d peak remains sharp in the pseudoga...

Electronic structure investigation of atomic layer deposition ruthenium(oxide) thin films using photoemission spectroscopy

Energy Technology Data Exchange (ETDEWEB)

Schaefer, Michael, E-mail: mvschaefer@mail.usf.edu, E-mail: schlaf@mail.usf.edu [Department of Physics, University of South Florida, Tampa, Florida 33620 (United States); Schlaf, Rudy, E-mail: mvschaefer@mail.usf.edu, E-mail: schlaf@mail.usf.edu [Department of Electrical Engineering, University of South Florida, Tampa, Florida 33620 (United States)

2015-08-14

Analyzing and manipulating the electronic band line-up of interfaces in novel micro- and nanoelectronic devices is important to achieve further advancement in this field. Such band alignment modifications can be achieved by introducing thin conformal interfacial dipole layers. Atomic layer deposition (ALD), enabling angstrom-precise control over thin film thickness, is an ideal technique for this challenge. Ruthenium (Ru{sup 0}) and its oxide (RuO{sub 2}) have gained interest in the past decade as interfacial dipole layers because of their favorable properties like metal-equivalent work functions, conductivity, etc. In this study, initial results of the electronic structure investigation of ALD Ru{sup 0} and RuO{sub 2} films via photoemission spectroscopy are presented. These experiments give insight into the band alignment, growth behavior, surface structure termination, and dipole formation. The experiments were performed in an integrated vacuum system attached to a home-built, stop-flow type ALD reactor without exposing the samples to the ambient in between deposition and analysis. Bis(ethylcyclopentadienyl)ruthenium(II) was used as precursor and oxygen as reactant. The analysis chamber was outfitted with X-ray photoemission spectroscopy (LIXPS, XPS). The determined growth modes are consistent with a strong growth inhibition situation with a maximum average growth rate of 0.21 Å/cycle for RuO{sub 2} and 0.04 Å/cycle for Ru.{sup 0} An interface dipole of up to −0.93 eV was observed, supporting the assumption of a strongly physisorbed interface. A separate experiment where the surface of a RuO film was sputtered suggests that the surface is terminated by an intermediate, stable, non-stoichiometric RuO{sub 2}/OH compound whose surface is saturated with hydroxyl groups.

Electronic structure investigation of atomic layer deposition ruthenium(oxide) thin films using photoemission spectroscopy

International Nuclear Information System (INIS)

Schaefer, Michael; Schlaf, Rudy

2015-01-01

Analyzing and manipulating the electronic band line-up of interfaces in novel micro- and nanoelectronic devices is important to achieve further advancement in this field. Such band alignment modifications can be achieved by introducing thin conformal interfacial dipole layers. Atomic layer deposition (ALD), enabling angstrom-precise control over thin film thickness, is an ideal technique for this challenge. Ruthenium (Ru 0 ) and its oxide (RuO 2 ) have gained interest in the past decade as interfacial dipole layers because of their favorable properties like metal-equivalent work functions, conductivity, etc. In this study, initial results of the electronic structure investigation of ALD Ru 0 and RuO 2 films via photoemission spectroscopy are presented. These experiments give insight into the band alignment, growth behavior, surface structure termination, and dipole formation. The experiments were performed in an integrated vacuum system attached to a home-built, stop-flow type ALD reactor without exposing the samples to the ambient in between deposition and analysis. Bis(ethylcyclopentadienyl)ruthenium(II) was used as precursor and oxygen as reactant. The analysis chamber was outfitted with X-ray photoemission spectroscopy (LIXPS, XPS). The determined growth modes are consistent with a strong growth inhibition situation with a maximum average growth rate of 0.21 Å/cycle for RuO 2 and 0.04 Å/cycle for Ru. 0 An interface dipole of up to −0.93 eV was observed, supporting the assumption of a strongly physisorbed interface. A separate experiment where the surface of a RuO film was sputtered suggests that the surface is terminated by an intermediate, stable, non-stoichiometric RuO 2 /OH compound whose surface is saturated with hydroxyl groups

Impact of interface charge on the electrostatics of field-plate assisted RESURF devices

NARCIS (Netherlands)

Boksteen, B.K.; Ferrara, A.; Heringa, A.; Steeneken, P.G.; Hueting, Raymond Josephus Engelbart

2014-01-01

A systematic study on the effects of arbitrary parasitic charge profiles, such as trapped or fixed charge, on the 2-D potential distribution in the drain extension of reverse-biased field-plate-assisted reduced surface field (RESURF) devices is presented. Using TCAD device simulations and analytical

Calculations of Photoemission from Rutile

Science.gov (United States)

Hjalmarson, Harold; Schultz, Peter; Moore, Chris

2015-03-01

Photoemission is a well-known mechanism for release of electrons from a surface during electrical breakdown of a gas such as air. During air breakdown, UV photons, which are emitted from the highly excited gas molecules, are absorbed in the surfaces such as the cathode and the anode. These absorbed photons create energetic electrons, and a small portion of these electrons reach the surface. Those that overcome the potential energy barrier at the surface tend to be emitted. In this talk, the Boltzmann equation that describes these phenomena is formulated. A Monte Carlo probabilistic method is used to obtain the rate of electron emission as a function of photon energy. The role of bandstructure effects will be discussed. This bandstructure information is obtained by using a density-functional theory (DFT) method. Sandia National Laboratories is a multi-program laboratory managed and operated by Sandia Corporation, a wholly owned subsidiary of Lockheed Martin Corporation, for the U.S. Department of Energy's National Nuclear Security Administration under contract DE-AC04-94AL85000.

Final state selection in the 4p photoemission of Rb by combining laser spectroscopy with soft-x-ray photoionization

International Nuclear Information System (INIS)

Schulz, J.; Tchaplyguine, M.; Rander, T.; Bergersen, H.; Lindblad, A.; Oehrwall, G.; Svensson, S.; Heinaesmaeki, S.; Sankari, R.; Osmekhin, S.; Aksela, S.; Aksela, H.

2005-01-01

Fine structure resolved 4p photoemission studies have been performed on free rubidium atoms in the ground state and after excitation into the [Kr]5p 2 P 1/2 and 2 P 3/2 states. The 4p 5 5p final states have been excited in the 4p 6 5s→4p 5 5p conjugate shakeup process from ground state atoms as well as by direct photoemission from laser excited atoms. The relative intensities differ considerably in these three excitation schemes. The differences in the laser excited spectra could be described well using calculations based on the pure jK-coupling scheme. Thereby it was possible to specify the character of the various final states. Furthermore it has been possible to resolve two of the final states whose energy separation is smaller than the experimental resolution by selectively exciting them in a two step scheme, where the laser selects the spin-orbit coupling in the intermediate state and determines the final state coupling after x-ray photoemission

Angle-resolved photoemission spectroscopy with quantum gas microscopes

Science.gov (United States)

Bohrdt, A.; Greif, D.; Demler, E.; Knap, M.; Grusdt, F.

2018-03-01

Quantum gas microscopes are a promising tool to study interacting quantum many-body systems and bridge the gap between theoretical models and real materials. So far, they were limited to measurements of instantaneous correlation functions of the form 〈O ̂(t ) 〉 , even though extensions to frequency-resolved response functions 〈O ̂(t ) O ̂(0 ) 〉 would provide important information about the elementary excitations in a many-body system. For example, single-particle spectral functions, which are usually measured using photoemission experiments in electron systems, contain direct information about fractionalization and the quasiparticle excitation spectrum. Here, we propose a measurement scheme to experimentally access the momentum and energy-resolved spectral function in a quantum gas microscope with currently available techniques. As an example for possible applications, we numerically calculate the spectrum of a single hole excitation in one-dimensional t -J models with isotropic and anisotropic antiferromagnetic couplings. A sharp asymmetry in the distribution of spectral weight appears when a hole is created in an isotropic Heisenberg spin chain. This effect slowly vanishes for anisotropic spin interactions and disappears completely in the case of pure Ising interactions. The asymmetry strongly depends on the total magnetization of the spin chain, which can be tuned in experiments with quantum gas microscopes. An intuitive picture for the observed behavior is provided by a slave-fermion mean-field theory. The key properties of the spectra are visible at currently accessible temperatures.

Increase of intrinsic emittance induced by multiphoton photoemission from copper cathodes illuminated by femtosecond laser pulses

Science.gov (United States)

An, Chenjie; Zhu, Rui; Xu, Jun; Liu, Yaqi; Hu, Xiaopeng; Zhang, Jiasen; Yu, Dapeng

2018-05-01

Electron sources driven by femtosecond laser have important applications in many aspects, and the research about the intrinsic emittance is becoming more and more crucial. The intrinsic emittance of polycrystalline copper cathode, which was illuminated by femtosecond pulses (FWHM of the pulse duration was about 100 fs) with photon energies above and below the work function, was measured with an extremely low bunch charge (single-electron pulses) based on free expansion method. A minimum emittance was obtained at the photon energy very close to the effective work function of the cathode. When the photon energy decreased below the effective work function, emittance increased rather than decreased or flattened out to a constant. By investigating the dependence of photocurrent density on the incident laser intensity, we found the emission excited by pulsed photons with sub-work-function energies contained two-photon photoemission. In addition, the portion of two-photon photoemission current increased with the reduction of photon energy. We attributed the increase of emittance to the effect of two-photon photoemission. This work shows that conventional method of reducing the photon energy of excited light source to approach the room temperature limit of the intrinsic emittance may be infeasible for femtosecond laser. There would be an optimized photon energy value near the work function to obtain the lowest emittance for pulsed laser pumped photocathode.

High-energy photoemission studies of oxide interfaces

Science.gov (United States)

Claessen, Ralph

2015-03-01

The interfaces of complex oxide heterostructures can host novel quantum phases not existing in the bulk of the constituents, with the high-mobility 2D electron system (2DES) in LaAlO3/SrTiO3 (LAO/STO) representing a prominent example. Despite extensive research the origin of the 2DES and its unusual properties - including the supposed coexistence of superconductivity and ferromagnetism - are still a matter of intense debate. Photoelectron spectroscopy, recently extended into the soft (SX-ARPES) and hard (HAXPES) X-ray regime, is a powerful method to provide detailed insight into the electronic structure of these heterostructures and, in particular, of the buried interface. This includes the identification of the orbital character of the 2DES as well as the determination of vital band structure information, such as band alignment, band bending, and even k-resolved band dispersions and Fermi surface topology. Moreover, resonant photoemission at the Ti L-edge reveals the existence of two different species of Ti 3d states, localized and itinerant, which can be distinguished and identified by their different resonance behavior. The role of oxygen vacancies is studied by controlled in-situ oxidation, which allows us to vary the composition from fully stoichiometric to strongly O-deficient. By comparison to free STO surfaces we can thus demonstrate that the metallicity of the heteointerfaces is intrinsic, i . e . it persists even in the absence of O defects. I will discuss our photoemission results on LAO/STO heterostructures in both (100) and (111) orientation as well as on the related system γ-Al2O3/STO(100), which also hosts a 2DES with an even higher mobility. Work in collaboration with J. Mannhart (MPI-FKF, Stuttgart), N. Pryds (TU Denmark), G. Rijnders (U Twente), S. Suga (U Osaka), M. Giorgoi (BESSY, HZB), W. Drube (DESY Photon Science), V.N. Strocov (Swiss Light Source), J. Denlinger (Advanced Light Source, LBNL), and T.-L. Lee (Diamond Light Source). Support by

Angle-resolved photoemission spectroscopy of band tails in lightly doped cuprates

OpenAIRE

Alexandrov, A. S.; Reynolds, K.

2007-01-01

We amend ab initio strongly-correlated band structures by taking into account the band-tailing phenomenon in doped charge-transfer Mott-Hubbard insulators. We show that the photoemission from band tails accounts for sharp "quasi-particle" peaks, rapid loss of their intensities in some directions of the Brillouin zone ("Fermi-arcs") and high-energy "waterfall" anomalies as a consequence of matrix-element effects of disorder-localised states in the charge-transfer gap of doped cuprates.

Efficient temporal shaping of electron distributions for high-brightness photoemission electron guns

Directory of Open Access Journals (Sweden)

Ivan V. Bazarov

2008-04-01

Full Text Available To achieve the lowest emittance electron bunches from photoemission electron guns, it is essential to limit the uncorrelated emittance growth due to space charge forces acting on the bunch in the vicinity of the photocathode through appropriate temporal shaping of the optical pulses illuminating the photocathode. We present measurements of the temporal profile of electron bunches from a bulk crystal GaAs photocathode illuminated with 520 nm wavelength pulses from a frequency-doubled Yb-fiber laser. A transverse deflecting rf cavity was used to make these measurements. The measured laser pulse temporal profile and the corresponding electron beam temporal profile have about 30 ps FWHM duration, with rise and fall times of a few ps. GaAs illuminated by 520 nm optical pulses is a prompt emitter within our measurement uncertainty of ∼1  ps rms. Combined with the low thermal emittance of negative electron affinity photocathodes, GaAs is a very suitable photocathode for high-brightness photoinjectors. We also report measurements of the photoemission response time for GaAsP, which show a strong dependence on the quantum efficiency of the photocathode.

Transition to intermediate valence state and x-ray photoemission in Sm/sub 1-x/Gd/sub x/S

International Nuclear Information System (INIS)

Campagna, M.; Chui, S.T.; Wertheim, G.K.; Tosatti, E.

1976-01-01

We report a systematic x-ray photoemission study of the alloys Sm 1 /sub -//subx/Gd/subx/S for 0 2+ → Sm 3+ photoemission line shape using a model which has some similarities with the Jaccarino-Walker model for magnetic alloys. It assumes the existence of only two different kinds of Sm 2+ ions in Sm 1 /sub -//subx/Gd/subx/S for x approximately-less-than 16%. We discuss possible reasons for the fact that Gd does not show the usual clustering effects known to occur in many substitutional rare-earth alloys. Lattice-constant measurements for various substituents further illustrate the importance of electronic effects in the phase transition

Layer- and lateral-resolved magnetization studies using photoemission electron microscopy

International Nuclear Information System (INIS)

Wei, D.H.; Hsu, Y.J.; Lin, C.-C.; Lai, C.-H.; Ou, J.Y.; Wu, J.C.

2004-01-01

The magnetic circular dichroism in X-ray absorption is employed to study the element-specific magnetization in a TbFe/Co bilayer system and patterned Ni 80 Fe 20 film. Taking advantage of the energy tunability as well as the penetration power of synchrotron radiation, the magnetization directions of Co and Fe deposited in different layers were examined as a function of Co film thickness. For patterned films, the photoemission electron microscope reveals a clear correlation between the magnetic configurations and geometries of the patterns

Absence of photoemission from the Fermi level in potassium intercalated picene and coronene films: structure, polaron, or correlation physics?

Science.gov (United States)

Mahns, Benjamin; Roth, Friedrich; Knupfer, Martin

2012-04-07

The electronic structure of potassium intercalated picene and coronene films has been studied using photoemission spectroscopy. Picene has additionally been intercalated using sodium. Upon alkali metal addition core level as well as valence band photoemission data signal a filling of previously unoccupied states of the two molecular materials due to charge transfer from potassium. In contrast to the observation of superconductivity in K(x)picene and K(x)coronene (x ~ 3), none of the films studied shows emission from the Fermi level, i.e., we find no indication for a metallic ground state. Several reasons for this observation are discussed.

Angle-resolved photoemission spectroscopy on iron-chalcogenide superconductors

Energy Technology Data Exchange (ETDEWEB)

Maletz, Janek; Zabolotnyy, Volodymyr; Evtushinsky, Daniil; Thirupathaiah, Setti; Wolter-Giraud, Anja; Harnagea, Luminita; Kordyuk, Alexander; Borisenko, Sergey [IFW Dresden (Germany); Yaresko, Alexander [MPI-FKF, Stuttgart (Germany); Vasiliev, Alexander [Moscow State University (Russian Federation); Chareev, Dimitri [RAS, Chernogolovka (Russian Federation); Rienks, Emile [Helmholtz-Zentrum Berlin (Germany); Buechner, Bernd [IFW Dresden (Germany); TU Dresden (Germany); Shermadini, Zurab; Luetkens, Hubertus; Sedlak, Kamil; Khasanov, Rustem; Amato, Alex; Krzton-Maziopa, Anna; Conder, Kazimierz; Pomjakushina, Ekaterina [Paul Scherrer Institute (Switzerland); Klauss, Hans-Henning [TU Dresden (Germany)

2014-07-01

The electronic structure of the iron chalcogenide superconductors FeSe{sub 1-x} and Rb{sub 0.77}Fe{sub 1.61}Se{sub 2} was investigated by high-resolution angle-resolved photoemission spectroscopy (ARPES). The results were compared to DFT calculations and μSR measurements. Both compounds share ''cigar-shaped'' Fermi surface sheets in their electronic structure, that can be found in almost all iron-pnictide superconductors. These features originate from a strong interplay of two hole- and electron-like bands in the Brillouin zone center, leading to a pronounced singularity in the density of states just below the Fermi level. This facilitates the coupling to a bosonic mode responsible for superconductivity.

Photoemission-monitored x-ray standing wave studies of molecular adsorbate surface structure

International Nuclear Information System (INIS)

Lee, John Jethro

2002-01-01

The influence of non-dipole photoemission terms on the accuracy of photoemission-monitored NIXSW structure determinations has been studied. An experimental survey has been made of values of the incoherent dipole-quadrupole parameter as a function of energy and atomic number for the Is states of elements between carbon and chlorine inclusive. These values are compared with recent theoretical calculations. The contribution of the coherent dipole-quadrupole interference terms, whose form has been theoretically derived recently, has been experimentally measured for Is photoemission from clean Al(111). The coherent dipole-quadrupole effect is found to be small and easily corrected for, while the previously-known incoherent effect is shown to result in tolerable errors in most cases. Adsorption of methyl thiol (CH 3 SH) on Pt(111), followed by annealing to ∼ 220 K is believed to result in the formation of methyl thiolate (-SCH 3 ). Two structural models are consistent with NIXSW data presented here: co-occupation of fcc and hcp sites, and a tilted atop-bonded geometry. On annealing to ∼500 K, complete dissociation occurs, and the remaining S atoms are found to lie in fcc sites, with evidence of partial occupation of a more complex phase. The adsorption of CO, NO and O on Ni(111), and the O+CO and O+NO coadsorbate systems have been investigated with NIXSW. The sites found for O, CO and NO are consistent with previous quantitative structure determinations. In the presence of a precoverage of oxygen, the conclusion of a recent photoelectron diffraction study that the preferred CO site is atop a substrate Ni atom is confirmed. In contrast, NO adsorption onto a (2 x 2)-O precovered surface is found to result in the restructuring of the oxygen layer, with NO adsorbing in the hollow sites, as in the pure-NO layer. Discrepancies in bond lengths between these NIXSW results and previous quantitative determinations are discussed. (author)

Magnetic field-assisted electrochemical discharge machining

International Nuclear Information System (INIS)

Cheng, Chih-Ping; Mai, Chao-Chuang; Wu, Kun-Ling; Hsu, Yu-Shan; Yan, Biing-Hwa

2010-01-01

Electrochemical discharge machining (ECDM) is an effective unconventional method for micromachining in non-conducting materials, such as glass, quartz and some ceramics. However, since the spark discharge performance becomes unpredictable as the machining depth increases, it is hard to achieve precision geometry and efficient machining rate in ECDM drilling. One of the main factors for this is the lack of sufficient electrolyte flow in the narrow gap between the tool and the workpiece. In this study a magnetohydrodynamic (MHD) convection, which enhances electrolyte circulation has been applied to the ECDM process in order to upgrade the machining accuracy and efficiency. During electrolysis in the presence of a magnetic field, the Lorenz force induces the charged ions to form a MHD convection. The MHD convection then forces the electrolyte into movement, thus enhancing circulation of electrolyte. Experimental results show that the MHD convection induced by the magnetic field can effectively enhance electrolyte circulation in the micro-hole, which contributes to higher machining efficiency. Micro-holes in glass with a depth of 450 µm are drilled in less than 20 s. At the same time, better electrolyte circulation can prevent deterioration of gas film quality with increasing machining depth, while ensuring stable electrochemical discharge. The improvement in the entrance diameter thus achieved was 23.8% while that in machining time reached 57.4%. The magnetic field-assisted approach proposed in the research does not require changes in the machining setup or electrolyte but has proved to achieve significant enhancement in both accuracy and efficiency of ECDM.

AC electric field assisted orientational photorefractive effect in C60-doped nematic liquid crystal

International Nuclear Information System (INIS)

Sun Xiudong; Pei Yanbo; Yao Fengfeng; Zhang Jianlong; Hou Chunfeng

2007-01-01

Photorefractive gratings were produced in a C 60 -doped nematic liquid crystal cell under the application of two coherent beams and a nonbiased sinusoidal ac electric field. The beam coupling and diffraction of the ac electric field assisted gratings were studied systematically. A stable asymmetric energy transference was obtained. Diffraction was observed when the angle (between the normal of the cell and the bisector of the writing beams) was 0 0 , and the dependence of diffraction efficiency on the peak-to-peak value of the ac voltage was similar to that at an incidence angle of 45 0 , suggesting that the role of the ac field was to facilitate the charge separation, and the space-charge field (SCF) originated predominantly from the diffusion of the ac electric field assisted photo-induced carriers under the application of nonuniform illumination and an applied ac field. The grating was produced by director reorientation induced by the cooperation of the SCF and the applied ac electric field. A self-erasing phenomenon was observed in this cell. An explanation in terms of the movement of two kinds of carriers with opposite signs was proposed

Electronic Structures of Purple Bronze KMo6O17 Studied by X-Ray Photoemission Spectra

Science.gov (United States)

Qin, Xiaokui; Wei, Junyin; Shi, Jing; Tian, Mingliang; Chen, Hong; Tian, Decheng

X-ray photoemission spectroscopy study has been performed for the purple bronze KMo6O17. The structures of conduction band and valence band are analogous to the results of ultraviolet photoemission spectra and are also consistent with the model of Travaglini et al., but the gap between conduction and valence band is insignificant. The shape of asymmetric and broadening line of O-1s is due to unresolved contributions from the many inequivalent oxygen sites in this crystal structure. Mo 3d core-level spectrum reveals that there are two kinds of valence states of Molybdenum (Mo+5 and Mo+6). The calculated average valence state is about +5.6, which is consistent with the expectation value from the composition of this material. The tail of Mo-3d spectrum toward higher binding energy is the consequence of the excitation of electron-hole pairs with singularity index of 0.21.

Electron attachment rate constant measurement by photoemission electron attachment ion mobility spectrometry (PE-EA-IMS)

International Nuclear Information System (INIS)

Su, Desheng; Niu, Wenqi; Liu, Sheng; Shen, Chengyin; Huang, Chaoqun; Wang, Hongmei; Jiang, Haihe; Chu, Yannan

2012-01-01

Photoemission electron attachment ion mobility spectrometry (PE-EA-IMS), with a source of photoelectrons induced by vacuum ultraviolet radiation on a metal surface, has been developed to study electron attachment reaction at atmospheric pressure using nitrogen as the buffer gas. Based on the negative ion mobility spectra, the rate constants for electron attachment to tetrachloromethane and chloroform were measured at ambient temperature as a function of the average electron energy in the range from 0.29 to 0.96 eV. The experimental results are in good agreement with the data reported in the literature. - Highlights: ► Photoemission electron attachment ion mobility spectrometry (PE-EA-IMS) was developed to study electron attachment reaction. ► The rate constants of electron attachment to CCl 4 and CHCl 3 were determined. ► The present experimental results are in good agreement with the previously reported data.

Multiphoton photoemission from a copper cathode illuminated by ultrashort laser pulses in an RF photoinjector.

Science.gov (United States)

Musumeci, P; Cultrera, L; Ferrario, M; Filippetto, D; Gatti, G; Gutierrez, M S; Moody, J T; Moore, N; Rosenzweig, J B; Scoby, C M; Travish, G; Vicario, C

2010-02-26

In this Letter we report on the use of ultrashort infrared laser pulses to generate a copious amount of electrons by a copper cathode in an rf photoinjector. The charge yield verifies the generalized Fowler-Dubridge theory for multiphoton photoemission. The emission is verified to be prompt using a two pulse autocorrelation technique. The thermal emittance associated with the excess kinetic energy from the emission process is comparable with the one measured using frequency tripled uv laser pulses. In the high field of the rf gun, up to 50 pC of charge can be extracted from the cathode using a 80 fs long, 2 microJ, 800 nm pulse focused to a 140 mum rms spot size. Taking into account the efficiency of harmonic conversion, illuminating a cathode directly with ir laser pulses can be the most efficient way to employ the available laser power.

Multiphoton Photoemission from a Copper Cathode Illuminated by Ultrashort Laser Pulses in an rf Photoinjector

International Nuclear Information System (INIS)

Musumeci, P.; Gutierrez, M. S.; Moody, J. T.; Moore, N.; Rosenzweig, J. B.; Scoby, C. M.; Travish, G.; Cultrera, L.; Ferrario, M.; Filippetto, D.; Gatti, G.; Vicario, C.

2010-01-01

In this Letter we report on the use of ultrashort infrared laser pulses to generate a copious amount of electrons by a copper cathode in an rf photoinjector. The charge yield verifies the generalized Fowler-Dubridge theory for multiphoton photoemission. The emission is verified to be prompt using a two pulse autocorrelation technique. The thermal emittance associated with the excess kinetic energy from the emission process is comparable with the one measured using frequency tripled uv laser pulses. In the high field of the rf gun, up to 50 pC of charge can be extracted from the cathode using a 80 fs long, 2 μJ, 800 nm pulse focused to a 140 μm rms spot size. Taking into account the efficiency of harmonic conversion, illuminating a cathode directly with ir laser pulses can be the most efficient way to employ the available laser power.

Laser-excited photoemission spectroscopy study of superconducting boron-doped diamond

Directory of Open Access Journals (Sweden)

K. Ishizaka, R. Eguchi, S. Tsuda, T. Kiss, T. Shimojima, T. Yokoya, S. Shin, T. Togashi, S. Watanabe, C.-T. Chen, C.Q. Zhang, Y. Takano, M. Nagao, I. Sakaguchi, T. Takenouchi and H. Kawarada

2006-01-01

Full Text Available We have investigated the low-energy electronic state of boron-doped diamond thin film by the laser-excited photoemission spectroscopy. A clear Fermi-edge is observed for samples doped above the semiconductor–metal boundary, together with the characteristic structures at 150×n meV possibly due to the strong electron–lattice coupling effect. In addition, for the superconducting sample, we observed a shift of the leading edge below Tc indicative of a superconducting gap opening. We discuss the electron–lattice coupling and the superconductivity in doped diamond.

Study of III-V semiconductor band structure by synchrotron photoemission

International Nuclear Information System (INIS)

Williams, G.P.; Cerrina, F.; Anderson, J.; Lapeyre, G.J.; Smith, R.J.; Hermanson, J.; Knapp, J.A.

1982-01-01

Angle-resolved synchrotron photoemission studies of six III-V semiconductors have been carried out. For emission normal to the (110) plane of these materials, peaks in the experimental spectra were identified with the bands involved in the transitions, and the critical point energies X 3 , X 5 , and Σ 1 /sup min/, were determined. The data indicate that k perpendicular is conserved in the transitions. Comparison of the data with theoretical bands permits an evaluation of k perpendicular associated with the experimentally observed transition, and from this information the bands were plotted out

Phonon-assisted hopping of an electron on a Wannier-Stark ladder in a strong electric field

International Nuclear Information System (INIS)

Emin, D.; Hart, C.F.

1987-01-01

With the application of a spatially constant electric field, the degeneracy of electronic energy levels of geometrically equivalent sites of a crystal is generally lifted. As a result, the electric field causes the electronic eigenstates of a one-dimensional periodic chain to become localized. In particular, they are Wannier-Stark states. With sufficiently large electric-field strengths these states become sufficiently well localized that it becomes appropriate to consider electronic transport to occur via a succession of phonon-assisted hops between the localized Wannier-Stark states. In this paper, we present calculations of the drift velocity arising from acoustic- and optical-phonon-assisted hopping motion between Wannier-Stark states. When the intersite electronic transfer energy is sufficiently small so that the Wannier-Stark states are essentially each confined to a single atomic site, the transport reduces to that of a small polaron. In this regime, while the drift velocity initially rises with increasing electric field strength, the drift velocity ultimately falls with increasing electric-field strength at extremely large electric fields. More generally, for common values of the electronic bandwidth and electric field strength, the Wannier-Stark states span many sites. At sufficiently large electric fields, the energy separation between Wannier-Stark states exceeds the energy uncertainty associated with the carrier's interaction with phonons. Then, it is appropriate to treat the electronic transport in terms of phonon-assisted hopping between Wannier-Stark states. The resulting high-field drift velocity falls with increasing field strength in a series of steps. Thus, we find a structured negative differential mobility at large electric fields

Method to map one-dimensional electronic wave function by using multiple Brillouin zone angle resolved photoemission

Directory of Open Access Journals (Sweden)

Dong-Wook Lee

2010-10-01

Full Text Available Angle resolved photoemission spectroscopy (ARPES is a powerful tool to investigate electronic structures in solids and has been widely used in studying various materials. The electronic structure information by ARPES is obtained in the momentum space. However, in the case of one-dimensional system, we here show that we extract the real space information from ARPES data taken over multiple Brillouin zones (BZs. Intensities in the multiple BZs are proportional to the photoemission matrix element which contains information on the coefficient of the Bloch wave function. It is shown that the Bloch wave function coefficients can be extracted from ARPES data, which allows us to construct the real space wave function. As a test, we use ARPES data from proto-typical one-dimensional system SrCuO2 and construct the real space wave function.

Chirped Auger electron emission due to field-assisted post-collision interaction

Directory of Open Access Journals (Sweden)

Bonitz M.

2013-03-01

Full Text Available We have investigated the Auger decay in the temporal domain by applying a terahertz streaking light field. Xenon and krypton atoms were studied by implementing the free-electron laser in Hamburg (FLASH as well as a source of high-order harmonic radiation combined with terahertz pulses from an optical rectification source. The observed linewidth asymmetries in the streaked spectra suggest a chirped Auger electron emission which is understood in terms of field-assisted post-collision interaction. The experimentally obtained results agree well with model calculations.

Synthesis and in vacuo deposition of iron oxide nanoparticles by microplasma-assisted decomposition of ferrocene

International Nuclear Information System (INIS)

Schaefer, Michael; Kumar, Ajay; Mohan Sankaran, R.; Schlaf, Rudy

2014-01-01

Microplasma-assisted gas-phase nucleation has emerged as an important new approach to produce high-purity, nanometer-sized, and narrowly dispersed particles. This study aims to integrate this technique with vacuum conditions to enable synthesis and deposition in an ultrahigh vacuum compatible environment. The ultimate goal is to combine nanoparticle synthesis with photoemission spectroscopy-based electronic structure analysis. Such measurements require in vacuo deposition to prevent surface contamination from sample transfer, which can be deleterious for nanoscale materials. A homebuilt microplasma reactor was integrated into an existing atomic layer deposition system attached to a surface science multi-chamber system equipped with photoemission spectroscopy. As proof-of-concept, we studied the decomposition of ferrocene vapor in the microplasma to synthesize iron oxide nanoparticles. The injection parameters were optimized to achieve complete precursor decomposition under vacuum conditions, and nanoparticles were successfully deposited. The stoichiometry of the deposited samples was characterized in situ using X-ray photoelectron spectroscopy indicating that iron oxide was formed. Additional transmission electron spectroscopy characterization allowed the determination of the size, shape, and crystal lattice of the particles, confirming their structural properties.

Experimental investigation of an optimum configuration for a high-voltage photoemission gun for operation at ≥500  kV

Directory of Open Access Journals (Sweden)

Nobuyuki Nishimori

2014-05-01

Full Text Available We demonstrated the generation of a 500-keV electron beam from a high dc voltage photoemission gun for an energy recovery linac light source [N. Nishimori et al., Appl. Phys. Lett. 102, 234103 (2013]. This demonstration was achieved by addressing two discharge problems that lead to vacuum breakdown in the dc gun. One is field emission generated from a central stem electrode. We employed a segmented insulator to protect the ceramic insulator surface from the field emission. The other is microdischarge at an anode electrode or a vacuum chamber, which is triggered by microparticle transfer or field emission from a cathode electrode. An experimental investigation revealed that a larger acceleration gap, optimized mainly to reduce the surface electric field of the anode electrode, suppresses the microdischarge events that accompany gas desorption. It was also found that nonevaporable getter pumps placed around the acceleration gap greatly help to suppress those microdischarge events. The applied voltage as a function of the total gas desorption is shown to be a good measure for finding the optimum dc gun configuration.

Invited Article: High resolution angle resolved photoemission with tabletop 11 eV laser

Energy Technology Data Exchange (ETDEWEB)

He, Yu; Vishik, Inna M.; Yi, Ming; Yang, Shuolong; Lee, James J.; Chen, Sudi; Rebec, Slavko N.; Leuenberger, Dominik; Shen, Zhi-Xun [SIMES, SLAC National Accelerator Laboratory, Menlo Park, California 94025 (United States); Department of Applied Physics, Stanford University, Stanford, California 94305 (United States); Liu, Zhongkai [SIMES, SLAC National Accelerator Laboratory, Menlo Park, California 94025 (United States); Department of Physics, Stanford University, Stanford, California 94305 (United States); Zong, Alfred [Department of Physics, Stanford University, Stanford, California 94305 (United States); Jefferson, C. Michael; Merriam, Andrew J. [Lumeras LLC, 207 McPherson St, Santa Cruz, California 95060 (United States); Moore, Robert G.; Kirchmann, Patrick S. [SIMES, SLAC National Accelerator Laboratory, Menlo Park, California 94025 (United States)

2016-01-15

We developed a table-top vacuum ultraviolet (VUV) laser with 113.778 nm wavelength (10.897 eV) and demonstrated its viability as a photon source for high resolution angle-resolved photoemission spectroscopy (ARPES). This sub-nanosecond pulsed VUV laser operates at a repetition rate of 10 MHz, provides a flux of 2 × 10{sup 12} photons/s, and enables photoemission with energy and momentum resolutions better than 2 meV and 0.012 Å{sup −1}, respectively. Space-charge induced energy shifts and spectral broadenings can be reduced below 2 meV. The setup reaches electron momenta up to 1.2 Å{sup −1}, granting full access to the first Brillouin zone of most materials. Control over the linear polarization, repetition rate, and photon flux of the VUV source facilitates ARPES investigations of a broad range of quantum materials, bridging the application gap between contemporary low energy laser-based ARPES and synchrotron-based ARPES. We describe the principles and operational characteristics of this source and showcase its performance for rare earth metal tritellurides, high temperature cuprate superconductors, and iron-based superconductors.

Synchrotron-radiation photoemission study of CdS/CuInSe2 heterojunction formation

International Nuclear Information System (INIS)

Nelson, A.J.; Gebhard, S.; Rockett, A.; Colavita, E.; Engelhardt, M.; Hoechst, H.

1990-01-01

Synchrotron-radiation soft-x-ray photoemission spectroscopy was used to investigate the development of the electronic structure at the CdS/CuInSe 2 heterojunction interface. CdS overlayers were deposited in steps on single-crystal p- and n-type CuInSe 2 at 250 degree C. Results indicate that the CdS grows in registry with the substrate, initially in a two-dimensional growth mode followed by three-dimensional island growth as is corroborated by reflection high-energy electron-diffraction analysis. Photoemission measurements were acquired after each growth in order to observe changes in the valence-band electronic structure as well as changes in the In 4d, Se 3d, Cd 4d, and S 2p core lines. The results were used to correlate the interface chemistry with the electronic structure at these interfaces and to directly determine the CdS/CuInSe 2 heterojunction valence-band discontinuity and the consequent heterojunction band diagram. These results show that the Katnani-Margaritondo method is unreliable in determining offsets for heterojunctions where significant Fermi-level pinning may occur and where the local structure and chemistry of the interface depends strongly on the specific heterojunction

Image enhancement in photoemission electron microscopy by means of imaging time-of-flight analysis

International Nuclear Information System (INIS)

Oelsner, A.; Krasyuk, A.; Fecher, G.H.; Schneider, C.M.; Schoenhense, G.

2004-01-01

Photoemission electron microscopy (PEEM) is widely used in combination with synchrotron sources as a powerful tool to observe chemical and magnetic properties of metal and semiconductor surfaces. Presently, the resolution limit of these instruments using soft-X-ray excitation is limited to about 50 nm, because of the chromatic aberration of the electron optics used. Various sophisticated approaches have thus been reported for enhancing the spatial resolution in photoemission electron microscopy. This work demonstrates the use of a simple imaging energy filter based on electron time-of-flight (ToF) selection. The spatial resolution could be improved dramatically, even though the instrument was optimized using a rather large contrast aperture of 50 μm. A special (x, y, t)-resolving delayline detector was used as the imaging unit of this ToF-PEEM. It is operated in phase with the time structure of the synchrotron source, cutting time intervals from the raw image-forming data set in order to reduce the electron energy width contributing to the final images

Study on Electric field assisted low frequency (20 kHz) ultrasonic spray

Science.gov (United States)

Chae, Ilkyeong; Seong, Baekhoon; Marten, Darmawan; Byun, Doyoung

2015-11-01

Ultrasonic spray is one of the fabulous techniques to discharge small size of droplets because it utilizes ultrasonic vibration on nozzle. However, spray patterns and size of ejected droplet is hardly controlled in conventional ultrasonic spray method. Therefore, here we present electric field assisted ultrasonic spray, which combined conventional technique with electric field in order to control spray pattern and droplet size precisely. Six kinds of various liquid (D.I water, Ethanol, Acetone, Iso-propanol, Toluene, Hexane) with various dielectric constants were used to investigate the mechanism of this method. Also, PIV (Particle Image Velocimetry) was used and various variables were obtained including spray angle, amplitude of liquid vibration, current, and size distribution of ejected droplets. Our electric field assisted ultrasonic spray show that the standard deviation of atomized droplet was decreased up to 39.6%, and it shows the infinite possibility to be utilized in various applications which require precise control of high transfer efficiency. This work was supported by the Basic Science Research Program through the National Research Foundation of Korea (NRF) funded by the Ministry of Education, Science and Technology (2014-023284).

Ultrafast transmission electron microscopy using a laser-driven field emitter: Femtosecond resolution with a high coherence electron beam

Energy Technology Data Exchange (ETDEWEB)

Feist, Armin; Bach, Nora; Rubiano da Silva, Nara; Danz, Thomas; Möller, Marcel; Priebe, Katharina E.; Domröse, Till; Gatzmann, J. Gregor; Rost, Stefan; Schauss, Jakob; Strauch, Stefanie; Bormann, Reiner; Sivis, Murat; Schäfer, Sascha, E-mail: sascha.schaefer@phys.uni-goettingen.de; Ropers, Claus, E-mail: claus.ropers@uni-goettingen.de

2017-05-15

We present the development of the first ultrafast transmission electron microscope (UTEM) driven by localized photoemission from a field emitter cathode. We describe the implementation of the instrument, the photoemitter concept and the quantitative electron beam parameters achieved. Establishing a new source for ultrafast TEM, the Göttingen UTEM employs nano-localized linear photoemission from a Schottky emitter, which enables operation with freely tunable temporal structure, from continuous wave to femtosecond pulsed mode. Using this emission mechanism, we achieve record pulse properties in ultrafast electron microscopy of 9 Å focused beam diameter, 200 fs pulse duration and 0.6 eV energy width. We illustrate the possibility to conduct ultrafast imaging, diffraction, holography and spectroscopy with this instrument and also discuss opportunities to harness quantum coherent interactions between intense laser fields and free-electron beams. - Highlights: • First implementation of an ultrafast TEM employing a nanoscale photocathode. • Localized single photon-photoemission from nanoscopic field emitter yields low emittance ultrashort electron pulses. • Electron pulses focused down to ~9 Å, with a duration of 200 fs and an energy width of 0.6 eV are demonstrated. • Quantitative characterization of ultrafast electron gun emittance and brightness. • A range of applications of high coherence ultrashort electron pulses is shown.

Observation of electron polarization above 80% in photoemission from strained III-V compounds

International Nuclear Information System (INIS)

Garwin, E.L.; Maruyama, T.; Prepost, R.; Zapalac, G.H.

1992-02-01

Spin-polarized electron photoemission has been investigated for strained III--V compounds; (1) strained In x Ga 1-x As epitaxially grown on a GaAs substrate, and (2) strained GaAs grown on a GaAs 1-x P x buffer layer. The lattice mismatched heterostructure results in a highly strained epitaxial layer, and electron spin polarization as high as 90% has been observed

New type of in-gap states at a spinel/perovskite interface: combined resonant soft x-ray photoemission spectroscopy and first-principles study.

Science.gov (United States)

Borisov, Vladislav; Schuetz, Philipp; Pfaff, Florian; Scheiderer, Philipp; Dudy, Lenart; Zapf, Michael; Gabel, Judith; Christensen, Dennis Valbjorn; Chen, Yunzhong; Pryds, Nini; Strocov, Vladimir; Rogalev, Victor; Schlueter, Christoph; Lee, Tien-Lin; Jeschke, Harald O.; Valenti, Roser; Sing, Michael; Claessen, Ralph

Oxygen vacancies in oxide heterostructures create a plethora of electronic phenomena not observed in the stoichiometric systems. In this talk we will discuss the presence of a new type of in-gap states at the spinel/perovskite γ-Al2O3/SrTiO3 interface, as observed in soft x-ray resonant photoemission spectroscopy. Based on ab initio calculations and crystal-field analysis of different atomic environments, we identify the origin of this behavior and we argue on the possible origin of the extraordinarily high electron mobility measured in this heterostructure. This work was financially supported by the Deutsche Forschungsgemeinschaft SFB/TR 49 and SFB 1170.

Inner-shell photoemission from atoms and molecules using synchrotron radiation

International Nuclear Information System (INIS)

Lindle, D.W.

1983-12-01

Photoelectron spectroscopy, in conjunction with synchrotron radiation, has been used to study inner-shell photoemission from atoms and molecules. The time structure of the synchrotron radiation permits the measurements of time-of-flight (TOF) spectra of Auger and photoelectrons, thereby increasing the electron collection efficiency. The double-angle TOF method yielded angle-resolved photoelectron intensities, which were used to determine photoionization cross sections and photoelectron angular distributions in several cases. Comparison to theoretical calculations has been made where possible to help explain observed phenomena in terms of the electronic structure and photoionization dynamics of the systems studied. 154 references, 23 figures, 7 tables

Assisted of electromagnetic fields in glucose production from cassava stems

Science.gov (United States)

Lismeri, Lia; Haryati, Sri; Djoni Bustan, M.; Darni, Yuli

2018-03-01

Decrease in fossil fuel reserves that led to high price has become major problem in many countries around the world. To acquire the sustainability of energy reserves, the renewable energies obtained from plant biomass will therefore have to play an increasing role in fulfilling energy demand throughout the century. Renewable energy source must be explored by innovative techniques which is safe to the environment and low in energy consumptions. This research conducted to produce glucose from cassava stems assisted by electromagnetic field inductions process. The parameters used in this research were pretreatment solvent, concentration, temperature and electrical currents. The electromagnetic field inductions could be applied to increase glucose productivity with the maximum yield of glucose was 47.43%.

Untangling the contributions of image charge and laser profile for optimal photoemission of high-brightness electron beams

International Nuclear Information System (INIS)

Portman, J.; Zhang, H.; Makino, K.; Ruan, C. Y.; Berz, M.; Duxbury, P. M.

2014-01-01

Using our model for the simulation of photoemission of high brightness electron beams, we investigate the virtual cathode physics and the limits to spatio-temporal and spectroscopic resolution originating from the image charge on the surface and from the profile of the exciting laser pulse. By contrasting the effect of varying surface properties (leading to expanding or pinned image charge), laser profiles (Gaussian, uniform, and elliptical), and aspect ratios (pancake- and cigar-like) under different extraction field strengths and numbers of generated electrons, we quantify the effect of these experimental parameters on macroscopic pulse properties such as emittance, brightness (4D and 6D), coherence length, and energy spread. Based on our results, we outline optimal conditions of pulse generation for ultrafast electron microscope systems that take into account constraints on the number of generated electrons and on the required time resolution.

Photoemission and electron-stimulated desorption studies of H on W(110): Single- versus two-binding-site models

International Nuclear Information System (INIS)

Weng, S.

1982-01-01

The chemisorption of H on W(110) at room temperature is studied with the use of angle-integrated photoemission and electron-stimulated desorption (ESD). The ESD cross sections of H + are found to be sol low that no significant H + signals with meaningful ion energy distributions are observed. The photoemission results show, however, two types of H adatoms, referred to as β 2 and β 1 states, for this chemisorptive system. Both states are found to appear simultaneously rather than sequentially as suggested by previous studies, and exhibit a simple 1-theta adsorption kinetics with different initial sticking coefficients. The β 2 state induces two binding energy levels at -2.0 and -6.0 eV, respectively, whereas the β 1 state induces a level at -3.8 eV. The work-function change (with a maximum value of -0.45 eV) is found to follow exactly with the intensity of the β 2 state. These results are found to be compatible with the two-binding-site model, inherently suggested by the reflection high-enery electron-diffraction data. However, the results can also be consistent with a single-binding-site model suggested by a recent angle-resolved photoemission and inelastic electron scattering study. A model based on the present results is proposed and critically compared with previous studies. Unresolved problems associated with both single- and two-binding-site models are also discussed

On the excess photon noise in single-beam measurements with photo-emissive and photo-conductive cells

NARCIS (Netherlands)

Alkemade, C.T.J.

In this paper the so-called excess photon noise is theoretically considered with regard to noise power measurements with a single, illumined photo-emissive or photo-conductive cell. Starting from a modification of Mandel's stochastic association of the emission of photo-electrons with wave

Valency and type conversion in CuInSe2 with H2 plasma exposure: A photoemission investigation

International Nuclear Information System (INIS)

Nelson, A.J.; Frigo, S.P.; Rosenberg, R.

1993-01-01

The effect of H 2 plasma exposure on CuInSe 2 was studied by synchrotron radiation soft-x-ray photoemission spectroscopy. The low-power H 2 plasma was generated with a commercial electron cyclotron resonance plasma source using pure H 2 with the plasma exposure being performed at 200 degree C. In situ photoemission measurements were acquired after each plasma exposure in order to observe changes in the valence-band electronic structure as well as changes in the In 4d and Se 3d core lines. The results were correlated in order to relate changes in surface chemistry to the electronic structure. These measurements indicate that the H 2 plasma exposure type converts the CuInSe 2 surface to an n-type surface as well as converting the In +3 valency state to an In +1 valency state

Field Test of Advanced Duct-Sealing Technologies Within the Weatherization Assistance Program

Energy Technology Data Exchange (ETDEWEB)

Ternes, MP

2001-12-05

A field test of an aerosol-spray duct-sealing technology and a conventional, best-practice approach was performed in 80 homes to determine the efficacy and programmatic needs of the duct-sealing technologies as applied in the U.S. Department of Energy Weatherization Assistance Program. The field test was performed in five states: Iowa, Virginia, Washington, West Virginia, and Wyoming. The study found that, compared with the best-practice approach, the aerosol-spray technology is 50% more effective at sealing duct leaks and can potentially reduce labor time and costs for duct sealing by 70%, or almost 4 crew-hours. Further study to encourage and promote use of the aerosol-spray technology within the Weatherization Assistance Program is recommended. A pilot test of full production weatherization programs using the aerosol-spray technology is recommended to develop approaches for integrating this technology with other energy conservation measures and minimizing impacts on weatherization agency logistics. In order to allow or improve adoption of the aerosol spray technology within the Weatherization Assistance Program, issues must be addressed concerning equipment costs, use of the technology under franchise arrangements with Aeroseal, Inc. (the holders of an exclusive license to use this technology), software used to control the equipment, safety, and training. Application testing of the aerosol-spray technology in mobile homes is also recommended.

Unoccupied Surface State on Ag(110) as Revealed by Inverse Photoemission

Science.gov (United States)

Reihl, B.; Schlittler, R. R.; Neff, H.

1984-05-01

By use of the new technique of k-resolved inverse photoemission spectroscopy, an unoccupied s-like surface state on Ag(110) has been detected, which lies within the projected L2'-->L1 gap of the bulk. At the X¯ point of the surface Brillouin zone, the energy of the surface state is 1.65 eV above the Fermi level EF, and exhibits a band dispersion E(k∥) towards higher energies. The surface-state emission is immediately quenched when the surface is exposed to very small amounts of oxygen or hydrogen.

Magnetic field assisted Fenton reactions for the enhanced degradation of methyl blue

Institute of Scientific and Technical Information of China (English)

Xiao Long Hao; Lu Yi Zou; Guang Sheng Zhang; Yi Bo Zhang

2009-01-01

Magnetic field was tentatively introduced into Fenton reactions system for the degradation and discoloration of methyl blue as the represent of organic chemical dye, which was a bio-refractory organic pollutant in industry wastewater. It was found that under optimal Fenton reaction conditions, with the assistant of magnetic field in Fenton reactions, the degradation rate of methyl blue, the decomposition rate of H2O2 and the conversion rate of Fe2+ were accelerated, the extent of them would be improved by the increase of magnetic field intensity. Meanwhile, the mineralization of methyl blue (CODcr) was improved by over 10% with magnetic fiold.

Bulk electronic state of high-Tc cuprate La2-xSrxCuO4 observed by high-energy angle integrated and resolved photoemission spectroscopy

International Nuclear Information System (INIS)

Kasai, S.; Sekiyama, A.; Tsunekawa, M.; Ernst, P.T.; Shigemoto, A.; Yamasaki, A.; Irizawa, A.; Imada, S.; Sing, M.; Muro, T.; Sasagawa, T.; Takagi, H.; Suga, S.

2005-01-01

The high-energy core-level photoemission spectroscopy (PES) and angle-resolved photoemission spectroscopy (ARPES) measurements have been performed for La 2-x Sr x CuO 4 (LSCO). Polar-angle dependence of the Cu 2p core-level PES has revealed a discrepancy between bulk and surface. We have observed by the high-energy ARPES that the Fermi surface of LSCO with x=0.16 is electron-like, in contrast to previous low-energy ARPES results

Bulk electronic structures of n-type superconductor Nd1.85Ce0.15CuO4 probed by high energy angle-resolved photoemission spectroscopy

International Nuclear Information System (INIS)

Tsunekawa, M.; Sekiyama, A.; Kasai, S.; Yamasaki, A.; Fujiwara, H.; Sing, M.; Shigemoto, A.; Imada, S.; Onose, Y.; Tokura, Y.; Muro, T.; Suga, S.

2005-01-01

We report on a high-energy angle-resolved photoemission (ARPES) study of the n-type high-T C cuprate, Nd 1.85 Ce 0.15 CuO 4 (NCCO). Our bulk sensitive results suggest a hole-like Fermi surface as seen by the so far reported low-energy ARPES studies. The soft X-ray Cu 2p core-level photoemission spectra show clear polar-angle dependence, suggesting the difference in electron states between the bulk and surface

Electronic structure of Sr2RuO4 studied by angle-resolved photoemission spectroscopy

International Nuclear Information System (INIS)

Iwasawa, H.; Aiura, Y.; Saitoh, T.; Yoshida, Y.; Hase, I.; Ikeda, S.I.; Bando, H.; Kubota, M.; Ono, K.

2007-01-01

Electronic structure of the monolayer strontium ruthenate Sr 2 RuO 4 was investigated by high-resolution angle-resolved photoemission spectroscopy. We present photon-energy (hν) dependence of the electronic structure near the Fermi level along the ΓM line. The hν dependence has shown a strong spectral weight modulation of the Ru 4d xy and 4d zx bands

In situ photoemission spectroscopy using synchrotron radiation for O2 translational kinetic energy induced oxidation processes of partially-oxidized Si(001) surfaces

International Nuclear Information System (INIS)

Teraoka, Yuden; Yoshigoe, Akitaka

2001-01-01

The influence of translational kinetic energy of incident O 2 molecules for the passive oxidation process of partially-oxidized Si(001) surfaces has been studied by photoemission spectroscopy. The translational kinetic energy of O 2 molecules was controlled up to 3 eV by a supersonic seed beam technique using a high temperature nozzle. Two translational kinetic energy thresholds (1.0 eV and 2.6 eV) were found out in accordance with the first-principles calculation for the oxidation of clean surfaces. Si-2p photoemission spectra measured in representative translational kinetic energies revealed that the translational kinetic energy dependent oxidation of dimers and the second layer (subsurface) backbonds were caused by the direct dissociative chemisorption of O 2 molecules. Moreover, the difference in chemical bonds for oxygen atoms was found out to be as low and high binding energy components in O-1s photoemission spectra. Especially, the low binding energy component increased with increasing the translational kinetic energy that indicates the translational kinetic energy induced oxidation in backbonds. (author)

Time- and energy resolved photoemission electron microscopy-imaging of photoelectron time-of-flight analysis by means of pulsed excitations

International Nuclear Information System (INIS)

Oelsner, Andreas; Rohmer, Martin; Schneider, Christian; Bayer, Daniela; Schoenhense, Gerd; Aeschlimann, Martin

2010-01-01

The present work enlightens the developments in time- and energy resolved photoemission electron microscopy over the past few years. We describe basic principles of the technique and demonstrate different applications. An energy- and time-filtering photoemission electron microscopy (PEEM) for real-time spectroscopic imaging can be realized either by a retarding field or hemispherical energy analyzer or by using time-of-flight optics with a delay line detector. The latter method has the advantage of no data loss at all as all randomly incoming particles are measured not only by position but also by time. This is of particular interest for pump-probe experiments in the femtosecond and attosecond time scale where space charge processes drastically limit the maximum number of photoemitted electrons per laser pulse. This work focuses particularly on time-of-flight analysis using a novel delay line detector. Time and energy resolved PEEM instruments with delay line detectors enable 4D imaging (x, y, Δt, E Kin ) on a true counting basis. This allows a broad range of applications from real-time observation of dynamic phenomena at surfaces to fs time-of-flight spectro-microscopy and even aberration correction. By now, these time-of-flight analysis instruments achieve intrinsic time resolutions of 108 ps absolute and 13.5 ps relative. Very high permanent measurement speeds of more than 4 million events per second in random detection regimes have been realized using a standard USB2.0 interface. By means of this performance, the time-resolved PEEM technique enables to display evolutions of spatially resolved (<25 nm) and temporal sliced images life on any modern computer. The method allows dynamics investigations of variable electrical, magnetic, and optical near fields at surfaces and great prospects in dynamical adaptive photoelectron optics. For dynamical processes in the ps time scale such as magnetic domain wall movements, the time resolution of the delay line detectors

Valence band photoemission studies of clean metals

International Nuclear Information System (INIS)

Wehner, P.S.

1978-04-01

The application of Angle-Resolved Photoelectron Spectroscopy (ARPES) to crystalline solids and the utilization of such studies to illuminate several questions concerning the detailed electronic structure of such materials, are discussed. Specifically, by construction of a Direct Transition (DT) model and the utilization of energy-dependent angle-resolved normal photoemission in the photon energy range 32 eV < or = hν < or = 200 eV, the bulk band structure of copper is experimentally mapped out along three different directions in the Brillouin Zone; GAMMA to K, GAMMA to L, and GAMMA to X. In addition, various effects which influence the obtainable resolution in vector k-space, namely, thermal disorder, momentum broadening, and band mixing, are discussed and are shown to place severe limitations on the applicability of the DT model. Finally, a model for Angle-Resolved X-ray Photoelectron Spectroscopy (ARXPS) based on the symmetry of the initial-state wavefunctions is presented and compared to experimental results obtained from copper single crystals

Interfacial electronic structure of Na deposited on rubrene thin film studied by synchrotron radiation photoemission

International Nuclear Information System (INIS)

Wei, Ching-Hsuan; Cheng, Chiu-Ping; Lin, Hong-Cheu; Pi, Tun-Wen

2015-01-01

Graphical abstract: - Highlights: • Na deposited on rubrene had undergone three-stage development process via (1) atomic diffusion, (2) atomic incorporation in the surface region, (3) formation of a metallic film. • High resolution core-level photoemission was used to determine the location of the doped Na atoms, which is affiliated at the end position of the tetracene-like backbone. • Na metal was formed on the rubrene thin film. • Ionization potential of the organic molecule regulated with different Na doping concentration could be controllable and favorable in practical applications. - Abstract: The electronic structure of rubrene doped with various concentrations of Na was studied by synchrotron-radiation photoemission. Three stages of development were found with increasing Na concentration; Na penetrating deep into the organic film, followed by development of gap states, and ended with a metallic Na film. The charge transfer from Na to rubrene resulted in a vacuum-level shift. By doping Na into rubrene, we could control the IP of the organic molecule, which is favorable for application in organic semiconductor devices.

Bulk superconducting gap of V_3Si studied by low-energy ultrahigh-resolution photoemission spectroscopy

International Nuclear Information System (INIS)

Sato, T.; Souma, S.; Nakayama, K.; Sugawara, K.; Toyota, N.; Takahashi, T.

2016-01-01

Highlights: • We report ultrahigh-resolution photoemission spectroscopy of A15 compound V_3Si. • We found a sharp quasiparticle peak due to superconducting-gap opening. • The surface metallic component is negligibly small in the bulk-sensitive measurement. • We show that V_3Si is a single-gap s-wave superconductor. - Abstract: We have performed low-energy ultrahigh-resolution photoemission spectroscopy (PES) of A15 compound V_3Si with a xenon-plasma discharge lamp to elucidate the bulk superconducting gap. Below the superconducting transition temperature (T_c = 15.9 K), we found a sharp quasiparticle peak at the Fermi level in the PES spectrum. The gap spectrum is well fitted by a single s-wave superconducting-gap function together with a dip structure at ∼30 meV suggestive of a strong electron-phonon coupling. The anomalous in-gap state previously observed in the PES measurement with high-energy photons is absent or negligibly small in the present bulk-sensitive measurement. The present PES result shows that V_3Si is a single-gap s-wave superconductor.

Angle-resolved photoemission in high Tc cuprates from theoretical viewpoints

International Nuclear Information System (INIS)

Tohyama, T.; Maekawa, S.

2000-01-01

The angle-resolved photoemission (ARPES) technique has been developed rapidly over the last decade, accompanied by the improvement of energy and momentum resolutions. This technique has been established as the most powerful tool to investigate the high T c cuprate superconductors. We review recent ARPES data on the cuprates from a theoretical point of view, with emphasis on the systematic evolution of the spectral weight near the momentum (π, 0) from insulator to overdoped systems. The effects of charge stripes on the ARPES spectra are also reviewed. Some recent experimental and theoretical efforts to understand the superconducting state and the pseudogap phenomenon are discussed. (author)

Manipulation of local optical properties and structures in molybdenum-disulfide monolayers using electric field-assisted near-field techniques.

Science.gov (United States)

Nozaki, Junji; Fukumura, Musashi; Aoki, Takaaki; Maniwa, Yutaka; Yomogida, Yohei; Yanagi, Kazuhiro

2017-04-05

Remarkable optical properties, such as quantum light emission and large optical nonlinearity, have been observed in peculiar local sites of transition metal dichalcogenide monolayers, and the ability to tune such properties is of great importance for their optoelectronic applications. For that purpose, it is crucial to elucidate and tune their local optical properties simultaneously. Here, we develop an electric field-assisted near-field technique. Using this technique we can clarify and tune the local optical properties simultaneously with a spatial resolution of approximately 100 nm due to the electric field from the cantilever. The photoluminescence at local sites in molybdenum-disulfide (MoS 2 ) monolayers is reversibly modulated, and the inhomogeneity of the charge neutral points and quantum yields is suggested. We successfully etch MoS 2 crystals and fabricate nanoribbons using near-field techniques in combination with an electric field. This study creates a way to tune the local optical properties and to freely design the structural shapes of atomic monolayers using near-field optics.

Photoemission study of electronic structure of the half-metallic ferromagnet Co₃Sn₂S₂

OpenAIRE

Holder, M.; Dedkov, Y.; Kade, A.; Rosner, H.; Schnelle, W.; Leithe-Jasper, A.; Weihrich, R.; Molodtsov, S.

2009-01-01

Surface electronic structure of polycrystalline and single-crystalline samples of the half-metallic ferromagnet Co₃Sn₂S₂ was studied by means of angle-resolved and core-level photoemissions. The experiments were performed in temperature regimes both above and below a Curie temperature of 176.9 K. The spectroscopic results are compared to local-spin density approximation band-structure calculations for the bulk samples. It is found that the surface sensitive experimental data are generally rep...

Benchmarking of 3D space charge codes using direct phase space measurements from photoemission high voltage dc gun

Directory of Open Access Journals (Sweden)

Ivan V. Bazarov

2008-10-01

Full Text Available We present a comparison between space charge calculations and direct measurements of the transverse phase space of space charge dominated electron bunches from a high voltage dc photoemission gun followed by an emittance compensation solenoid magnet. The measurements were performed using a double-slit emittance measurement system over a range of bunch charge and solenoid current values. The data are compared with detailed simulations using the 3D space charge codes GPT and Parmela3D. The initial particle distributions were generated from measured transverse and temporal laser beam profiles at the photocathode. The beam brightness as a function of beam fraction is calculated for the measured phase space maps and found to approach within a factor of 2 the theoretical maximum set by the thermal energy and the accelerating field at the photocathode.

Trap assisted tunneling and its effect on subthreshold swing of tunnel field effect transistors

OpenAIRE

Sajjad, Redwan N.; Chern, Winston; Hoyt, Judy L.; Antoniadis, Dimitri A.

2016-01-01

We provide a detailed study of the interface Trap Assisted Tunneling (TAT) mechanism in tunnel field effect transistors to show how it contributes a major leakage current path before the Band To Band Tunneling (BTBT) is initiated. With a modified Shockley-Read-Hall formalism, we show that at room temperature, the phonon assisted TAT current always dominates and obscures the steep turn ON of the BTBT current for common densities of traps. Our results are applicable to top gate, double gate and...

New ambient pressure photoemission endstation at Advanced Light Source beamline 9.3.2

KAUST Repository

Grass, Michael E.; Karlsson, Patrik G.; Aksoy, Funda; Lundqvist, Måns; Wannberg, Björn; Mun, Bongjin S.; Hussain, Zahid; Liu, Zhi

2010-01-01

During the past decade, the application of ambient pressure photoemission spectroscopy (APPES) has been recognized as an important in situ tool to study environmental and materials science, energy related science, and many other fields. Several APPES endstations are currently under planning or development at the USA and international light sources, which will lead to a rapid expansion of this technique. The present work describes the design and performance of a new APPES instrument at the Advanced Light Source beamline 9.3.2 at Lawrence Berkeley National Laboratory. This new instrument, Scienta R4000 HiPP, is a result of collaboration between Advanced Light Source and its industrial partner VG-Scienta. The R4000 HiPP provides superior electron transmission as well as spectromicroscopy modes with 16 μm spatial resolution in one dimension and angle-resolved modes with simulated 0.5° angular resolution at 24° acceptance. Under maximum transmission mode, the electron detection efficiency is more than an order of magnitude better than the previous endstation at beamline 9.3.2. Herein we describe the design and performance of the system, which has been utilized to record spectra above 2 mbar. © 2010 American Institute of Physics.

CHARGE-TRANSFER SATELLITES AND MULTIPLET SPLITTING IN X-RAY PHOTOEMISSION SPECTRA OF LATE TRANSITION-METAL HALIDES

NARCIS (Netherlands)

OKADA, K; KOTANI, A; THOLE, BT

1992-01-01

Core-level X-ray photoemission spectra (XPS) are calculated for Ni and Co dihalides with an MX6 cluster model (M = Ni, Co; X = F, Cl, Br), where intra-atomic multiplet coupling as well as covalency mixing is taken into account. The effects of the intra-atomic configuration interaction between

High-resolution photoemission study of Nd1-xSrxMnO3

International Nuclear Information System (INIS)

Fujiwara, H.; Sekiyama, A.; Higashiya, A.; Konoike, K.; Tsunekawa, M.; Yamasaki, A.; Irizawa, A.; Imada, S.; Muro, T.; Noda, K.; Kuwahara, H.; Tokura, Y.; Suga, S.

2005-01-01

We have performed the bulk sensitive Mn 2p-3d resonant photoemission for Nd 1-x Sr x MnO 3 (x=0.40, 0.47, 0.50, 0.63) in order to reveal the Mn 3d electronic states. We will report the temperature and doping dependence of the Mn 3d spectral functions. The sudden spectral change for x=0.50 across the FM-COI transition shows the strong influence of the charge-ordering on the Mn 3d electronic states

Bogoliubov Angle, Particle-Hole Mixture and Angular Resolved Photoemission Spectroscopy in Superconductors

Energy Technology Data Exchange (ETDEWEB)

Balatsky, A.

2010-05-04

Superconducting excitations - Bogoliubov quasiparticles - are the quantum mechanical mixture of negatively charged electron (-e) and positively charged hole (+e). We propose a new observable for Angular Resolved Photoemission Spectroscopy (ARPES) studies that is the manifestation of the particle-hole entanglement of the superconducting quasiparticles. We call this observable a Bogoliubov angle. This angle measures the relative weight of particle and hole amplitude in the superconducting (Bogoliubov) quasiparticle. We show how this quantity can be measured by comparing the ratio of spectral intensities at positive and negative energies.

Dynamically assisted Schwinger effect beyond the spatially-uniform-field approximation

Science.gov (United States)

Aleksandrov, I. A.; Plunien, G.; Shabaev, V. M.

2018-06-01

We investigate the phenomenon of electron-positron pair production from vacuum in the presence of a strong electric field superimposed by a weak but fast varying pulse which substantially increases the total particle yield. We employ a nonperturbative numerical technique and perform the calculations beyond the spatially-uniform-field approximation, i.e., dipole approximation, taking into account the coordinate dependence of the fast component. The analysis of the main characteristics of the pair-production process (momentum spectra of particles and total amount of pairs) reveals a number of important features which are absent within the previously used approximation. In particular, the structure of the momentum distribution is modified both qualitatively and quantitatively, and the total number of pairs created as well as the enhancement factor due to dynamical assistance become significantly smaller.

Wiggler magnetic field assisted third harmonic generation in expanding clusters

Science.gov (United States)

Vij, Shivani

2018-04-01

A simple theoretical model is constructed to study the wiggler magnetic field assisted third harmonic generation of intense short pulse laser in a cluster in its expanding phase. The ponderomotive force of laser causes density perturbations in cluster electron density which couples with wiggler magnetic field to produce a nonlinear current that generates transverse third harmonic. An intense short pulse laser propagating through a gas embedded with atomic clusters, converts it into hot plasma balls via tunnel ionization. Initially, the electron plasma frequency inside the clusters ω pe > \\sqrt{3}{ω }1 (with ω 1 being the frequency of the laser). As the cluster expands under Coulomb force and hydrodynamic pressure, ω pe decreases to \\sqrt{3}{ω }1. At this time, there is resonant enhancement in the efficiency of the third harmonic generation. The efficiency of third harmonic generation is enhanced due to cluster plasmon resonance and by phase matching due to wiggler magnetic field. The effect of cluster size on the expansion rate is studied to observe that the clusters of different radii would expand differently. The impact of laser intensity and wiggler magnetic field on the efficiency of third harmonic generation is also explored.

A method for the experimental determination of surface photoemission core-level shifts for 3d transition metals

NARCIS (Netherlands)

Shamsutdinov, N.R.; Sloof, W.G.; Böttger, A.J.

2005-01-01

A method is presented to determine the photoelectron surface core-level shift (SCLS) of 3d transition metals using x-ray photoelectron spectroscopy. The experimental difficulties arising from the relatively large broadening of photoemission lines in the 3d transition series can be overcome by the

Surface type conversion of CuInSe2 with H2S plasma exposure: A photoemission investigation

International Nuclear Information System (INIS)

Nelson, A.J.; Frigo, S.P.; Rosenberg, R.

1995-01-01

Surface type conversion of CuInSe 2 by H 2 S plasma exposure was studied by synchrotron radiation soft x-ray photoemission spectroscopy. The low power H 2 S plasma was generated with a commercial electron cyclotron resonance plasma source using pure H 2 S with the plasma exposure being performed at 400 degree C. In situ photoemission measurements were acquired after each plasma exposure in order to observe changes in the valence band electronic structure as well as changes in the In 4d and Se 3d core lines. The results were correlated in order to relate changes in surface chemistry to the electronic structure. These measurements indicate that the H 2 S plasma exposure type converts the n-type CuInSe 2 surface to a p-type surface at this elevated temperature and that the magnitude of the band bending is 0.5 eV, resulting in a homojunction interface. copyright 1995 American Vacuum Society

Fermi Surface and Band Structure of (Ca,La)FeAs2 Superconductor from Angle-Resolved Photoemission Spectroscopy

International Nuclear Information System (INIS)

Liu Xu; Liu De-Fa; Zhao Lin; Guo Qi; Mu Qing-Ge; Chen Dong-Yun; Shen Bing; Yi He-Mian; Huang Jian-Wei; He Jun-Feng; Peng Ying-Ying; Liu Yan; He Shao-Long; Liu Guo-Dong; Dong Xiao-Li; Zhang Jun; Ren Zhi-An; Zhou Xing-Jiang; Chen Chuang-Tian; Xu Zu-Yan

2013-01-01

The (Ca,R)FeAs 2 (R=La, Pr, etc.) superconductors with a signature of superconductivity transition above 40 K possess a new kind of block layers that consist of zig-zag As chains. We report the electronic structure of the new (Ca,La)FeAs 2 superconductor investigated by both band structure calculations and high resolution angle-resolved photoemission spectroscopy measurements. Band structure calculations indicate that there are four hole-like bands around the zone center Γ(0,0) and two electron-like bands near the zone corner M(π, π) in CaFeAs 2 . In our angle-resolved photoemission measurements on (Ca 0.9 La 0.1 )FeAs 2 , we have observed three hole-like bands around the Γ point and one electron-like Fermi surface near the M(π, π) point. These results provide important information to compare and contrast with the electronic structure of other iron-based compounds in understanding the superconductivity mechanism in the iron-based superconductors. (express letter)

Dilution effect on the U 5f states in Au matrix: a photoemission spectroscopy study

Czech Academy of Sciences Publication Activity Database

Eloirdi, R.; Gouder, T.; Wastin, F.; Huber, F.; Shick, Alexander; Kolorenč, Jindřich

2011-01-01

Roč. 84, č. 23 (2011), 235143/1-235143/7 ISSN 1098-0121 R&D Projects: GA ČR(CZ) GAP204/10/0330; GA AV ČR IAA100100912 Institutional research plan: CEZ:AV0Z10100520 Keywords : x-ray photoemission * electronic-structure * photoelectron- spectroscopy * fermion systems Subject RIV: BM - Solid Matter Physics ; Magnetism Impact factor: 3.691, year: 2011

Environment-Assisted Speed-up of the Field Evolution in Cavity Quantum Electrodynamics.

Science.gov (United States)

Cimmarusti, A D; Yan, Z; Patterson, B D; Corcos, L P; Orozco, L A; Deffner, S

2015-06-12

We measure the quantum speed of the state evolution of the field in a weakly driven optical cavity QED system. To this end, the mode of the electromagnetic field is considered as a quantum system of interest with a preferential coupling to a tunable environment: the atoms. By controlling the environment, i.e., changing the number of atoms coupled to the optical cavity mode, an environment-assisted speed-up is realized: the quantum speed of the state repopulation in the optical cavity increases with the coupling strength between the optical cavity mode and this non-Markovian environment (the number of atoms).

Environment-Assisted Speed-up of the Field Evolution in Cavity Quantum Electrodynamics

International Nuclear Information System (INIS)

Cimmarusti, A. D.; Yan, Z.; Patterson, B. D.; Corcos, L. P.; Orozco, L. A.; Deffner, S.

2015-01-01

We measure the quantum speed of the state evolution of the field in a weakly-driven optical cavity QED system. To this end, the mode of the electromagnetic field is considered as a quantum system of interest with a preferential coupling to a tunable environment: the atoms. By controlling the environment, i.e., changing the number of atoms coupled to the optical cavity mode, an environment assisted speed-up is realized: the quantum speed of the state re-population in the optical cavity increases with the coupling strength between the optical cavity mode and this non-Markovian environment (the number of atoms)

Vacuum scanning capillary photoemission microscopy.

Science.gov (United States)

Aseyev, S A; Cherkun, A P; Mironov, B N; Petrunin, V V; Chekalin, S V

2017-08-01

We demonstrate the use of a conical capillary in a scanning probe microscopy for surface analysis. The probe can measure photoemission from a substrate by transmitting photoelectrons along the capillary as a function of probe position. The technique is demonstrated on a model substrate consisting of a gold reflecting layer on a compact disc which has been illuminated by an unfocused laser beam with a wavelength 400nm, from a femtosecond laser with a beam size of 4mm. A quartz capillary with a 2-µm aperture has been used in the experiments. The period of gold microstructure, shown to be 1.6µ, was measured by the conical probe operating in shear force mode. In shear force regime, the dielectric capillary has been used as a "classical" SPM tip, which provided images reflecting the surface topology. In a photoelectron regime photoelectrons passed through hollow tip and entered a detector. The spatial distribution of the recorded photoelectrons consisted of periodic mountain-valley strips, resembling the surface profile of the sample. Submicron spatial resolution has been achieved. This approach paves the way to study pulsed photodesorption of large organic molecular ions with high spatial and element resolution using the combination of a hollow-tip scanner with time-of-flight technique. Copyright © 2017 Elsevier B.V. All rights reserved.

Electronic properties of Nd{sub 2−x}Ce{sub x}CuO{sub 4+δ}: A hard X-ray photoemission investigation

Energy Technology Data Exchange (ETDEWEB)

Guarino, A., E-mail: guarino@sa.infn.it [CNR-SPIN-Salerno, Fisciano, SA (Italy); Dipartimento di Fisica “E. R. Caianiello” Università di Salerno, Fisciano, SA (Italy); Panaccione, G. [CNR-IOM Laboratorio TASC, AREA Science Park, 34012 Basovizza, TS (Italy); Offi, F. [CNISM and Dipartimento di Scienze, Università Roma Tre, Roma (Italy); Monaco, G. [Dipartimento di Fisica, Università di Trento, Trento (Italy); Fondacaro, A. [European Synchrotron Radiation Facility, BP 220, F-38042 Grenoble (France); Torelli, P. [CNR-IOM Laboratorio TASC, AREA Science Park, 34012 Basovizza, TS (Italy); Fittipaldi, R.; Vecchione, A. [CNR-SPIN-Salerno, Fisciano, SA (Italy); Pace, S.; Nigro, A. [CNR-SPIN-Salerno, Fisciano, SA (Italy); Dipartimento di Fisica “E. R. Caianiello” Università di Salerno, Fisciano, SA (Italy)

2016-10-15

Highlights: • We grow and characterize Nd{sub 2−x}Ce{sub x}CuO{sub 4+δ} samples as thin film and single crystal. • We study the Cu 2p levels of our samples by hard X-ray photoemission spectroscopy. • We investigate bulk features of the Nd{sub 2−x}Ce{sub x}CuO{sub 4+δ} samples. • Signature of the bulk response is correlated with the crystallinity of the samples. - Abstract: Cu 2p core levels spectra measured by X-ray photoemission spectroscopy of selected as-grown Nd{sub 2−x}Ce{sub x}CuO{sub 4+δ} samples are presented and discussed. The presence of a satellite peak in the 2p core level of Nd{sub 2−x}Ce{sub x}CuO{sub 4+δ} single crystal by hard X-ray photoemission is confirmed in all non-superconducting samples, films and single crystals investigated in this work. The comparison of the spectral features of the different samples suggests that the presence and the intensity of this satellite peak is not related to the electric transport properties, but to the texture characteristics.

High-sensitivity ultraviolet photoemission spectroscopy technique for direct detection of gap states in organic thin films

Energy Technology Data Exchange (ETDEWEB)

Bussolotti, Fabio, E-mail: fabio@ims.ac.jp

2015-10-01

Highlights: • Density of gap states in organic thin film was detected by photoemission spectroscopy. • Inert gas exposure affects the density of gap states in organic thin films. • Density of gap states controls the energy level alignment at the organic/inorganic and organic/organic interfaces. - Abstract: We developed ultrahigh sensitivity, low-background ultraviolet photoemission spectroscopy (UPS) technique which does not introduce detectable radiation damages into organic materials. The UPS allows to detect density of states of the order of ∼10{sup 16} states eV{sup −1} cm{sup −3} even for radiation-sensitive organic films, this results being comparable to electrical measurements of charge trapping centers. In this review we introduce the method of ultrahigh sensitivity photoemission measurement and we present some results on the energy distribution of gap states in pentacene (Pn) films deposited on SiO{sub 2} and Au(1 1 1) substrate. For Pn/SiO{sub 2} thin film the results show that exposure to inert gas (N{sub 2} and Ar) atmosphere produces a sharp rise in gap states from 10{sup 16} to 10{sup 18} states eV{sup −1} cm{sup −3} and pushes the Fermi level closer to the valence band (0.15–0.17 eV), as does exposure to O{sub 2} (0.20 eV), while no such gas-induced effects are observed for Pn/Au(1 1 1) system. The results demonstrate that these gap states originate from small imperfections in the Pn packing structure, which are induced by gas penetration into the film through the Pn crystal grain boundaries. Similar results were obtained for CuPc/F{sub 16}CuPc thin films, a prototypical example of donor/acceptor interface for photovoltaic application.

Athermal electron distribution probed by femtosecond multiphoton photoemission from image potential states

International Nuclear Information System (INIS)

Ferrini, Gabriele; Giannetti, Claudio; Pagliara, Stefania; Banfi, Francesco; Galimberti, Gianluca; Parmigiani, Fulvio

2005-01-01

Image potential states are populated through indirect, scattering-mediated multiphoton absorption induced by femtosecond laser pulses and revealed by single-photon photoemission. The measured effective mass is significantly different from that obtained with direct, resonant population. These features reveal a strong coupling of the electrons residing in the image potential state, outside the solid, with the underlying hot electron population created by the laser pulse. The coupling is mediated by a many-body scattering interaction between the image potential state electrons and bulk electrons in highly excited states

Optical study of HgCdTe infrared photodetectors using internal photoemission spectroscopy

International Nuclear Information System (INIS)

Lao, Yan-Feng; Unil Perera, A. G.; Wijewarnasuriya, Priyalal S.

2014-01-01

We report a study of internal photoemission spectroscopy (IPE) applied to a n-type Hg 1−x Cd x Te/Hg 1−y Cd y Te heterojunction. An exponential line-shape of the absorption tail in HgCdTe is identified by IPE fittings of the near-threshold quantum yield spectra. The reduction of quantum yield (at higher photon energy) below the fitting value is explained as a result of carrier-phonon scatterings. In addition, the obtained bias independence of the IPE threshold indicates a negligible electron barrier at the heterojunction interface

A novel probe of intrinsic electronic structure: hard X-ray photoemission spectroscopy

International Nuclear Information System (INIS)

Takata, Y.; Tamasaku, K.; Nishino, Y.; Miwa, D.; Yabashi, M.; Ikenaga, E.; Horiba, K.; Arita, M.; Shimada, K.; Namatame, H.; Nohira, H.; Hattori, T.; Soedergren, S.; Wannberg, B.; Taniguchi, M.; Shin, S.; Ishikawa, T.; Kobayashi, K.

2005-01-01

We have realized hard X-ray (HX) photoemission spectroscopy (PES) with high throughput and high-energy resolution for core level and valence band studies using high-energy and high-brilliance synchrotron radiation at SPring-8. This is a brand new method because large escape depth of high-energy photoelectrons enables us to probe intrinsic bulk states free from surface condition. By use of a newly developed electron energy analyzer and well-focused X-rays, high-energy resolution of 75 meV (E/ΔE 79,000) was realized for 5.95 keV photoelectrons

Correlation versus surface effects in photoemission of quasi-1D organic conductors

DEFF Research Database (Denmark)

Claessen, R.; Schwingenschlogl, U.; Sing, M.

2002-01-01

The absence of spectral weight at the Fermi level in photoemission spectra of quasi-1D organic conductors has been interpreted as possible evidence for an unusual many-body state. We demonstrate that great care must be exercised to draw this conclusion exclusively on the basis of a pseudogap....... A detailed surface characterization of the charge transfer salts (TMTSF)(2)PFt(6) and TTF-TCNQ shows that signatures of electronic correlations in the valence band spectra are strongly affected by surface effects and may even be completely obscured....

The impact of inverse photoemission spectroscopy measurements on regioregular poly(3-hexylthiophene) films

International Nuclear Information System (INIS)

Li, Zhi; Schlaf, Rudy; Sun, Siqi; Li, Xiao

2014-01-01

Inverse photoemission spectroscopy (IPES) enables the characterization of the density of states of unoccupied energy states above the Fermi level. However, due to the relatively high electron currents required to achieve useful signal to noise ratios, sample damage is a concern. Regioregular poly(3-hexylthiophene) (rr-P3HT) was used to systematically study the influence of electron radiation during IPES measurements on a prototypical conductive polymer. A series of IPES measurements exposing the samples to a range of electron fluxes was performed. An analysis of the electronic structure and the morphology showed that significant changes occurred in the investigated samples depending on the electron flux. X-ray diffraction results revealed that the root cause of the spectral changes is most likely related to crystallization of the film in an edge-on orientation. This was confirmed by Raman spectroscopy where both the C-C and C=C stretch modes shifted to lower frequencies after 5 IPES scans indicating a more ordered molecular structure. The observation of these stretch modes even after exposure to higher electron flux indicates that the main chemical structure of the P3HT molecules remains mostly intact during the IPES measurements. The absence of significant changes in C 1s and S 2p photoemission core level lines also confirmed this conclusion

Photoemission characteristics of thin GaAs-based heterojunction photocathodes

Energy Technology Data Exchange (ETDEWEB)

Feng, Cheng; Zhang, Yijun, E-mail: zhangyijun423@126.com; Qian, Yunsheng [Institute of Electronic Engineering and Optoelectronic Technology, Nanjing University of Science and Technology, Nanjing 210094 (China); Shi, Feng [Science and Technology on Low-Light-Level Night Vision Laboratory, Xi' an 710065 (China); Zou, Jijun [Engineering Research Center of Nuclear Technology Application (East China Institute of Technology), Ministry of Education, Nanchang 330013 (China); Zeng, Yugang [Changchun Institute of Optics, Fine Mechanics and Physics, Chinese Academy of Sciences, Changchun 130033 (China)

2015-01-14

To better understand the different photoemission mechanism of thin heterojunction photocathodes, the quantum efficiency models of reflection-mode and transmission-mode GaAs-based heterojunction photocathodes are revised based on one-dimensional continuity equations, wherein photoelectrons generated from both the emission layer and buffer layer are taken into account. By comparison of simulated results between the revised and conventional models, it is found that the electron contribution from the buffer layer to shortwave quantum efficiency is closely related to some factors, such as the thicknesses of emission layer and buffer layer and the interface recombination velocity. Besides, the experimental quantum efficiency data of reflection-mode and transmission-mode AlGaAs/GaAs photocathodes are well fitted to the revised models, which confirm the applicability of the revised quantum efficiency models.

Widespread spin polarization effects in photoemission from topological insulators

Energy Technology Data Exchange (ETDEWEB)

Jozwiak, C.; Chen, Y. L.; Fedorov, A. V.; Analytis, J. G.; Rotundu, C. R.; Schmid, A. K.; Denlinger, J. D.; Chuang, Y.-D.; Lee, D.-H.; Fisher, I. R.; Birgeneau, R. J.; Shen, Z.-X.; Hussain, Z.; Lanzara, A.

2011-06-22

High-resolution spin- and angle-resolved photoemission spectroscopy (spin-ARPES) was performed on the three-dimensional topological insulator Bi{sub 2}Se{sub 3} using a recently developed high-efficiency spectrometer. The topological surface state's helical spin structure is observed, in agreement with theoretical prediction. Spin textures of both chiralities, at energies above and below the Dirac point, are observed, and the spin structure is found to persist at room temperature. The measurements reveal additional unexpected spin polarization effects, which also originate from the spin-orbit interaction, but are well differentiated from topological physics by contrasting momentum and photon energy and polarization dependencies. These observations demonstrate significant deviations of photoelectron and quasiparticle spin polarizations. Our findings illustrate the inherent complexity of spin-resolved ARPES and demonstrate key considerations for interpreting experimental results.

Energy band dispersion in photoemission spectra of argon clusters

International Nuclear Information System (INIS)

Foerstel, Marko; Mucke, Melanie; Arion, Tiberiu; Lischke, Toralf; Barth, Silko; Ulrich, Volker; Ohrwall, Gunnar; Bjoerneholm, Olle; Hergenhahn, Uwe; Bradshaw, Alex M.

2011-01-01

Using photoemission we have investigated free argon clusters from a supersonic nozzle expansion in the photon energy range from threshold up to 28 eV. Measurements were performed both at high resolution with a hemispherical electrostatic energy analyser and at lower resolution with a magnetic bottle device. The latter experiments were performed for various mean cluster sizes. In addition to the ∼1.5 eV broad 3p-derived valence band seen in previous work, there is a sharper feature at ∼15 eV binding energy. Surprisingly for non-oriented clusters, this peak shifts smoothly in binding energy over the narrow photon energy range 15.5-17.7 eV, indicating energy band dispersion. The onset of this bulk band-like behaviour could be determined from the cluster size dependence.

Quantum Effects for a Proton in a Low-Barrier, Double-Well Potential: Core Level Photoemission Spectroscopy of Acetylacetone.

Science.gov (United States)

Feyer, Vitaliy; Prince, Kevin C; Coreno, Marcello; Melandri, Sonia; Maris, Assimo; Evangelisti, Luca; Caminati, Walther; Giuliano, Barbara M; Kjaergaard, Henrik G; Carravetta, Vincenzo

2018-02-01

We have performed core level photoemission spectroscopy of gaseous acetylacetone, its fully deuterated form, and two derivatives, benzoylacetone and dibenzoylmethane. These molecules show intramolecular hydrogen bonds, with a proton located in a double-well potential, whose barrier height is different for the three compounds. This has allowed us to examine the effect of the double-well potential on photoemission spectra. Two distinct O 1s core hole peaks are observed, previously assigned to two chemical states of oxygen. We provide an alternative assignment of the double-peak structure of O 1s spectra by taking full account of the extended nature of the wave function associated with the nuclear motion of the proton, the shape of the ground and final state potentials in which the proton is located, and the nonzero temperature of the samples. The peaks are explained in terms of an unusual Franck-Condon factor distribution.

Photoemission study of the skutterudite compounds CoSb sub 3 and RhSb sub 3

CERN Document Server

Ishii, H; Fujimori, A; Nagamoto, Y; Koyanagi, T; Sofo, J O

2002-01-01

We have studied the electronic structure of the skutterudite compounds CoSb sub 3 and Co(Sb sub 0 sub . sub 9 sub 6 Te sub 0 sub . sub 0 sub 4) sub 3 by photoemission spectroscopy. Valence-band spectra revealed that a significant amount Sb 5p states are present near the Fermi level and are hybridized with Co 3d states just below it. The spectra are well reproduced by the band-structure calculation, suggesting that the effect of electron correlations is not important. When Te is substituted for Sb and n-type carriers are doped into CoSb sub 3 , the spectra are shifted to higher binding energies as described by the rigid-band model. From this shift and the free-electron model for the conduction and valence bands, we have estimated the band gap of CoSb sub 3 to be 0.03-0.04 eV, consistent with transport measurements. Photoemission spectra of RhSb sub 3 have also been measured and revealed expected similarities to and differences from those of CoSb sub 3. Unusual temperature dependence has been observed for the s...

Dissociation of acetaldehyde in intense laser field: Coulomb explosion or field-assisted dissociation?

Science.gov (United States)

Elshakre, Mohamed E.; Gao, Lirong; Tang, Xiaoping; Wang, Sufan; Shu, Yafei; Kong, Fanao

2003-09-01

Dissociation of acetaldehyde in moderate strong laser field of 1013-1014W/cm2 was investigated. Singly charged parent ion CH3CHO+ and fragmental ions CH3+, CHO+, C2H4+, O+, CH2CHO+, and H+ were produced by 800 nm laser of 100 fs pulse duration and recorded by time-of-flight mass spectrometer. The CH3+ fragment further dissociated to CH2+, CH+, and C+ ions at higher intensity. Ab initio calculated results show that the singly-, doubly-, and triply charged parent ions are stable. So, the dissociation mechanism was not due to Coulomb explosion of multicharged ion. A field-assisted dissociation (FAD) theory, which assumes that only one bond undergoes dissociation while the rest of the molecular geometry stays unchanged, was employed to treat the dissociation dynamics. Accordingly, the dressed potential energy surfaces of the ground state for the parent and the fragment ions were calculated. Corresponding quasiclassical trajectory calculations show that the bond ruptures take place in the order of C-C, C-O, and C-H, agreeing with the observation. The observed angular dependence and charge distribution of the product ions can also be interpreted by the FAD theory.

Photoemission study of S adsorption on GaAs (0 0 1)

International Nuclear Information System (INIS)

Strasser, T; Kipp, L; Skibowski, M; Schattke, W

2005-01-01

Angle-resolved photoemission spectra have been calculated with the one-step model for S/GaAs(0 0 1) and compared with experimental distributions. The data are analysed in terms of the ideal 1 x 1 and, furthermore, of the reconstructed 2 x 6 surface which is assumed to be closest to the experimentally realized structure. Emissions are characterized by electronic structure terms such as energy bands and orbital composition, though partly also by geometric properties. In particular, the determination of the second layer as consisting of Ga atoms has been achieved because of the distinct differences in the theoretical spectra with S-Ga and those with S-As bonds

Direct subwavelength imaging and control of near-field localization in individual silver nanocubes

Energy Technology Data Exchange (ETDEWEB)

Mårsell, Erik; Svärd, Robin; Miranda, Miguel; Guo, Chen; Harth, Anne; Lorek, Eleonora; Mauritsson, Johan; Arnold, Cord L.; L' Huillier, Anne; Mikkelsen, Anders; Losquin, Arthur, E-mail: arthur.losquin@fysik.lth.se [Department of Physics, Lund University, PO Box 118, 221 00 Lund (Sweden); Xu, Hongxing [Department of Physics, Lund University, PO Box 118, 221 00 Lund (Sweden); School of Physics and Technology and Institute for Advanced Studies, Wuhan University, Wuhan 430072 (China)

2015-11-16

We demonstrate the control of near-field localization within individual silver nanocubes through photoemission electron microscopy combined with broadband, few-cycle laser pulses. We find that the near-field is concentrated at the corners of the cubes, and that it can be efficiently localized to different individual corners depending on the polarization of the incoming light. The experimental results are confirmed by finite-difference time-domain simulations, which also provide an intuitive picture of polarization dependent near-field localization in nanocubes.

Valence-band and core-level photoemission study of single-crystal Bi2CaSr2Cu2O8 superconductors

International Nuclear Information System (INIS)

Shen, Z.; Lindberg, P.A.P.; Wells, B.O.; Mitzi, D.B.; Lindau, I.; Spicer, W.E.; Kapitulnik, A.

1988-01-01

High-quality single crystals of Bi 2 CaSr 2 Cu 2 O 8 superconductors have been prepared and cleaved in ultrahigh vacuum. Low-energy electron diffraction measurements show that the surface structure is consistent with the bulk crystal structure. Ultraviolet photoemission and x-ray photoemission experiments were performed on these well-characterized sample surfaces. The valence-band and the core-level spectra obtained from the single-crystal surfaces are in agreement with spectra recorded from polycrystalline samples, justifying earlier results from polycrystalline samples. Cu satellites are observed both in the valence band and Cu 2p core level, signaling the strong correlation among the Cu 3d electrons. The O 1s core-level data exhibit a sharp, single peak at 529-eV binding energy without any clear satellite structures

An ultrafast angle-resolved photoemission apparatus for measuring complex materials

Science.gov (United States)

Smallwood, Christopher L.; Jozwiak, Christopher; Zhang, Wentao; Lanzara, Alessandra

2012-12-01

We present technical specifications for a high resolution time- and angle-resolved photoemission spectroscopy setup based on a hemispherical electron analyzer and cavity-dumped solid state Ti:sapphire laser used to generate pump and probe beams, respectively, at 1.48 and 5.93 eV. The pulse repetition rate can be tuned from 209 Hz to 54.3 MHz. Under typical operating settings the system has an overall energy resolution of 23 meV, an overall momentum resolution of 0.003 Å-1, and an overall time resolution of 310 fs. We illustrate the system capabilities with representative data on the cuprate superconductor Bi2Sr2CaCu2O8+δ. The descriptions and analyses presented here will inform new developments in ultrafast electron spectroscopy.

Charge-density-wave partial gap opening in quasi-2D KMo 6O 17 purple bronze studied by angle resolved photoemission spectroscopy

Science.gov (United States)

Valbuena, M. A.; Avila, J.; Pantin, V.; Drouard, S.; Guyot, H.; Asensio, M. C.

2006-05-01

Low dimensional (LD) metallic oxides have been a subject of continuous interest in the last two decades, mainly due to the electronic instabilities that they present at low temperatures. In particular, charge density waves (CDW) instabilities associated with a strong electron-phonon interaction have been found in Molybdenum metallic oxides such as KMo 6O 17 purple bronze. We report an angle resolved photoemission (ARPES) study from room temperature (RT) to T ˜40 K well below the Peierls transition temperature for this material, with CDW transition temperature TCDW ˜120 K. We have focused on photoemission spectra along ΓM high symmetry direction as well as photoemission measurements were taken as a function of temperature at one representative kF point in the Brillouin zone in order to look for the characteristic gap opening after the phase transition. We found out a pseudogap opening and a decrease in the density of states near the Fermi energy, EF, consistent with the partial removal of the nested portions of the Fermi surface (FS) at temperature below the CDW transition. In order to elucidate possible Fermi liquid (FL) or non-Fermi liquid (NFL) behaviour we have compared the ARPES data with that one reported on quasi-1D K 0.3MoO 3 blue bronze.

Photoemission microscopy study of picosecond magnetodynamics in spin-valve-type thin film elements

International Nuclear Information System (INIS)

Schneider, C.M.; Kaiser, A.; Wiemann, C.; Tieg, C.; Cramm, S.

2010-01-01

Exploring ultimate time scales of magnetic switching processes is an important issue in spin electronics. In spin valves or magnetic tunnelling junctions magnetic anisotropies and coupling phenomena alter the magnetodynamic response of the entire system. Understanding the role of these interactions is a key to the design of optimized devices. We have employed time-resolved X-ray photoemission microscopy to address the magnetodynamics in spin-valve-type model systems in the ns- and ps-regime. In Co/Cr/Fe(0 0 1) single crystal elements we find a strong influence of the magnetocrystalline anisotropy, which tends to suppress rotation processes. In addition, we observe a dynamic 'decoupling' of the layers. In low-anisotropy FeNi/Cr/FeCo trilayers, the interlayer coupling character determines the dynamic response. Particularly, rotational processes in the FeNi and FeCo layers are temporarily shifted to each other, which can be related to different coercivities of the individual layers. By contrast, the domain wall motion in both layers closely agrees, caused by an enhanced coupling due to the domain wall stray fields. Our examples demonstrate that the detailed magnetodynamics in coupled magnetic layers is quite complex and depends strongly on the timescale under consideration.

Directional uv photoemission from (100) and (110) molybdenum surfaces

DEFF Research Database (Denmark)

Cinti, R. C.; Khoury, E. Al; Chakraverty, B. K.

1976-01-01

A study of the (100) and (110) molybdenum surfaces by directional photoemission spectroscopy is presented. Energy distribution spectra formed by photoelectrons emitted normal to the surfaces have been measured for photon energies between 10.2 and 21.2 eV. The results are discussed in terms of cal......-transition and surface-emission processes. Two extra structures are interpreted in terms of surface states or resonances: on the (100) surface, 0.5 eV below EF; on the (110) surface, 4.5 eV below EF in the s-d hybridization gap....... of calculated band structure within the framework of the K∥-conservation assumption. A good agreement is found between the main features of the experimental spectra and the emission expected from the band structure along the corresponding symmetry line in the Brillouin zone, assuming essentially direct...

EU assistance for sustainable development of the nuclear field in Romania

International Nuclear Information System (INIS)

Geambasu, C.; Popadiuc, S.; Comsa, O.

2006-01-01

For Romania, the acceptance of the doctrine of sustainable development of the nuclear field represents the only responsible way of designing the development on medium and long term, according to the national interest and the requirements of international co-operation. Now, PHARE Program, as an opportunity for all Romanian power industry to join to EU requirements for integration, will continue to provide assistance to Romania for accelerating and completing preparations for its access to the European Union. Using EU assistance, Romania will achieve the main goals for the next years focused on: informing the officials, local administration and general public about nuclear power and its development, in direct connection with safety and environmental issues; promote new modern technologies in national industry, especially for building the second unit in Cernavoda; provide support for the national nuclear power program, according the EU integration tasks. Indicators of sustainable development in the energy sector are the subjects of present and future efforts within the EU. (author)

Soft X-ray photoemission study of organic conductors BEDT-TTF and BEDO-TTF salts

International Nuclear Information System (INIS)

Tsunekawa, M.; Sekiyama, A.; Imada, S.; Saita, T.; Maesato, M.; Yamochi, H.; Saito, G.; Suga, S.

2005-01-01

We have performed a soft X-ray photoemission (PES) study of quasi-two-dimensional organic conductors BEDT-TTF (ET) and BEDO-TTF (BO) salts. We have clarified the difference in the electronic states between the bulk and surface insulating layers. The difference of the electronic states between ET and BO molecules is also found. On the other hand, the spectral weight in the vicinity of Fermi level is suppressed as reported by the low-energy PES

A new approach for 3D reconstruction from bright field TEM imaging: Beam precession assisted electron tomography

International Nuclear Information System (INIS)

Rebled, J.M.; Yedra, Ll.; Estrade, S.; Portillo, J.; Peiro, F.

2011-01-01

The successful combination of electron beam precession and bright field electron tomography for 3D reconstruction is reported. Beam precession is demonstrated to be a powerful technique to reduce the contrast artifacts due to diffraction and curvature in thin foils. Taking advantage of these benefits, Precession assisted electron tomography has been applied to reconstruct the morphology of Sn precipitates embedded in an Al matrix, from a tilt series acquired in a range from +49 o to -61 o at intervals of 2 o and with a precession angle of 0.6 o in bright field mode. The combination of electron tomography and beam precession in conventional TEM mode is proposed as an alternative procedure to obtain 3D reconstructions of nano-objects without a scanning system or a high angle annular dark field detector. -- Highlights: → Electron beam precession reduces spurious diffraction contrast in bright field mode. → Bend contour related contrast depends on precession angle. → Electron beam precession is combined with bright field electron tomography. → Precession assisted BF tomography allowed 3D reconstruction of a Sn precipitate.

Valence-band discontinuities of wurtzite GaN, AlN, and InN heterojunctions measured by x-ray photoemission spectroscopy

International Nuclear Information System (INIS)

Martin, G.; Botchkarev, A.; Rockett, A.; Morkoc, H.

1996-01-01

The valence-band discontinuities at various wurtzite GaN, AlN, and InN heterojunctions were measured by means of x-ray photoemission spectroscopy. A significant forward endash backward asymmetry was observed in the InN/GaN endash GaN/InN and InN/AlN endash AlN/InN heterojunctions. The asymmetry was understood as a piezoelectric strain effect. We report the valence band discontinuities for InN/GaN=1.05±0.25 eV, GaN/AlN=0.70±0.24 eV, and InN/AlN=1.81±0.20 eV, all in the standard type I lineup. These values obey transitivity to within the experimental accuracy. Tables of photoemission core level binding energies are reported for wurtzite GaN, AlN, and InN. copyright 1996 American Institute of Physics

Photoemission electron microscopy for the study of ferromagnetic and antiferromagnetic materials

International Nuclear Information System (INIS)

Anders, Simone; Scholl, Andreas; Nolting, Frithjof; Padmore, Howard A.; Luening, Jan; Stoehr, Joachim; Scheinfein, Michael

2000-01-01

Photoemission electron microscopy (PEEM) is a full field imaging technique where x-ray exited electrons are used to form an image of the sample surface as a function of the x-ray photon energy and polarization. Contrast in PEEM can be due to a number of mechanisms including topographical, work function, elemental, chemical, polarization, x-ray magnetic circular and linear dichroism contrast. This wide range of contrast mechanisms together with the surface sensitivity and high spatial resolution make PEEM a very useful tool for the study of magnetic materials. PEEM-II is a new microscope installed at the bending magnet beamline 7.3.1.1 of the Advanced Light Source. In the present paper we describe the design and features of PEEM-II, and show results of our recent studies. Using PEEM and its elemental specificity, it is possible to investigate the various layers in magnetic multilayer structures independently. The experiments described here include the investigation of the switching behavior of magnetic multilayer structures that are of interest for magnetic RAM applications. The study of antiferromagnetic surfaces and thin films are of great importance for devices based on the effect of exchange bias. To date, studies at high-spatial-resolution of exchange bias systems has been difficult because of the lack of appropriate investigation methods. Here we demonstrate how PEEM has been used to image antiferromagnetic structure on surfaces with high spatial resolution

Xclaim: A graphical interface for the calculation of core-hole spectroscopies

International Nuclear Information System (INIS)

Fernández-Rodríguez, Javier; Toby, Brian; Veenendaal, Michel van

2015-01-01

Highlights: • The program Xclaim (X-ray core level atomic multiplets) calculates core-hole spectra. • Crystal field under an arbitrary point symmetry and hybridization with ligands. • X-ray absorption spectroscopy (XAS), X-ray photoemission spectroscopy (XPS), photoemission spectroscopy (PES) and inverse photoemission (IPES). - Abstract: Xclaim (X-ray core level atomic multiplets) is a graphical interface for the calculation of core-hole spectroscopy and ground state properties within a charge-transfer multiplet model taking into account a many-body Hamiltonian with Coulomb, spin–orbit, crystal-field, and hybridization interactions. Using Coulomb and spin–orbit parameters calculated in the Hartree–Fock limit and ligand field parameters (crystal-field, hybridization and charge-transfer energy) the program calculates X-ray absorption spectroscopy (XAS), X-ray photoemission spectroscopy (XPS), photoemission spectroscopy (PES) and inverse photoemission (IPES). The program runs on Linux, Windows and MacOS platforms

Xclaim: A graphical interface for the calculation of core-hole spectroscopies

Energy Technology Data Exchange (ETDEWEB)

Fernández-Rodríguez, Javier [Department of Physics, Northern Illinois University, DeKalb, IL 60115 (United States); Advanced Photon Source, Argonne National Laboratory, 9700 South Cass Avenue, Argonne, IL 60439 (United States); Toby, Brian, E-mail: toby@anl.gov [Advanced Photon Source, Argonne National Laboratory, 9700 South Cass Avenue, Argonne, IL 60439 (United States); Veenendaal, Michel van, E-mail: veenendaal@niu.edu [Department of Physics, Northern Illinois University, DeKalb, IL 60115 (United States); Advanced Photon Source, Argonne National Laboratory, 9700 South Cass Avenue, Argonne, IL 60439 (United States)

2015-07-15

Highlights: • The program Xclaim (X-ray core level atomic multiplets) calculates core-hole spectra. • Crystal field under an arbitrary point symmetry and hybridization with ligands. • X-ray absorption spectroscopy (XAS), X-ray photoemission spectroscopy (XPS), photoemission spectroscopy (PES) and inverse photoemission (IPES). - Abstract: Xclaim (X-ray core level atomic multiplets) is a graphical interface for the calculation of core-hole spectroscopy and ground state properties within a charge-transfer multiplet model taking into account a many-body Hamiltonian with Coulomb, spin–orbit, crystal-field, and hybridization interactions. Using Coulomb and spin–orbit parameters calculated in the Hartree–Fock limit and ligand field parameters (crystal-field, hybridization and charge-transfer energy) the program calculates X-ray absorption spectroscopy (XAS), X-ray photoemission spectroscopy (XPS), photoemission spectroscopy (PES) and inverse photoemission (IPES). The program runs on Linux, Windows and MacOS platforms.

Bulk superconducting gap of V{sub 3}Si studied by low-energy ultrahigh-resolution photoemission spectroscopy

Energy Technology Data Exchange (ETDEWEB)

Sato, T., E-mail: t-sato@arpes.phys.tohoku.ac.jp [Department of Physics, Tohoku University, Sendai 980-8578 (Japan); Souma, S. [WPI Research Center, Advanced Institute for Materials Research, Tohoku University, Sendai 980-8577 (Japan); Nakayama, K. [Department of Physics, Tohoku University, Sendai 980-8578 (Japan); Sugawara, K. [WPI Research Center, Advanced Institute for Materials Research, Tohoku University, Sendai 980-8577 (Japan); Toyota, N. [Department of Physics, Tohoku University, Sendai 980-8578 (Japan); Takahashi, T. [Department of Physics, Tohoku University, Sendai 980-8578 (Japan); WPI Research Center, Advanced Institute for Materials Research, Tohoku University, Sendai 980-8577 (Japan)

2016-04-15

Highlights: • We report ultrahigh-resolution photoemission spectroscopy of A15 compound V{sub 3}Si. • We found a sharp quasiparticle peak due to superconducting-gap opening. • The surface metallic component is negligibly small in the bulk-sensitive measurement. • We show that V{sub 3}Si is a single-gap s-wave superconductor. - Abstract: We have performed low-energy ultrahigh-resolution photoemission spectroscopy (PES) of A15 compound V{sub 3}Si with a xenon-plasma discharge lamp to elucidate the bulk superconducting gap. Below the superconducting transition temperature (T{sub c} = 15.9 K), we found a sharp quasiparticle peak at the Fermi level in the PES spectrum. The gap spectrum is well fitted by a single s-wave superconducting-gap function together with a dip structure at ∼30 meV suggestive of a strong electron-phonon coupling. The anomalous in-gap state previously observed in the PES measurement with high-energy photons is absent or negligibly small in the present bulk-sensitive measurement. The present PES result shows that V{sub 3}Si is a single-gap s-wave superconductor.

Reversible switching in self-assembled monolayers of azobenzene thiolates on Au (111) probed by threshold photoemission

Energy Technology Data Exchange (ETDEWEB)

Heinemann, Nils, E-mail: heinemann@physik.uni-kiel.de [Institut fuer Experimentelle und Angewandte Physik, Christian-Albrechts-Universitaet zu Kiel, Leibnizstr. 19, 24098 Kiel (Germany); Grunau, Jan; Leissner, Till; Andreyev, Oleksiy; Kuhn, Sonja; Jung, Ulrich [Institut fuer Experimentelle und Angewandte Physik, Christian-Albrechts-Universitaet zu Kiel, Leibnizstr. 19, 24098 Kiel (Germany); Zargarani, Dordaneh; Herges, Rainer [Otto-Diels-Institut fuer Organische Chemie, Christian-Albrechts-Universitaet zu Kiel, Otto-Hahn-Platz 4, 24098 Kiel (Germany); Magnussen, Olaf; Bauer, Michael [Institut fuer Experimentelle und Angewandte Physik, Christian-Albrechts-Universitaet zu Kiel, Leibnizstr. 19, 24098 Kiel (Germany)

2012-06-19

Highlights: Black-Right-Pointing-Pointer Photoelectron spectroscopy of liquid phase prepared SAMs of azobenzene derivative. Black-Right-Pointing-Pointer Photo-induced reversible switching in densely packed SAM is monitored. Black-Right-Pointing-Pointer Maximum density of switched molecules in SAM is derived from photoemission data. Black-Right-Pointing-Pointer Switching reaction only enabled at defects sites within the molecular layer. - Abstract: The reversible photo- and thermally activated isomerization of the molecular switch 3-(4-(4-Hexyl-phenylazo)-phenoxy)-propane-1-thiol (ABT, short for AzoBenzeneThiol) deposited by self-assembly from solution on Au (111) was studied using laser-based photoelectron spectroscopy. Differences in the molecular dipole moment characteristic for the trans and the cis isomer of ABT were monitored via changes in the sample work function, accessible by detection of the threshold energy for photoemission. A quantitative analysis of our data shows that the fraction of molecules within the densely packed monolayer that undergoes a switching process is of the order of 1%. This result indicates the relevance of substrate and film defects required to overcome the steric or electronic hindrance of the isomerization reaction in a densely packed monolayer.

Soft x-ray photoemission investigation of the oxidation of CuInSe/sub 2/ thin films

International Nuclear Information System (INIS)

Zurcher, P.; Nelson, A.J.; Johnson, P.; Lapeyre, G.J.; Noufi, R.

1987-01-01

CuInSe/sub 2/ films are used as absorber layers in heterojunction thin film solar cells. It has been demonstrated that, depending on the stoichiometry, oxygen annealing can make CuInSe/sub 2/ films more p-type or even convert n-type films into p-type while subsequent reduction with hydrazine will reverse such processes. Using synchrotron radiation soft x-ray photoemission spectroscopy, the authors found associated with the hydrazine reduced films an In1+ state that converts into In3+ under the influence of oxygen at elevated sample temperatures. The samples investigated were grown in a way that the top several thousand Angstroms are increasingly Cu-poor and In-rich. It is this region which is sampled by the surface sensitive technique of photoemission. The Cu-poor/In-rich top regions will most likely have a large number of intrinsic In on Cu-site defects leaving the In in a 1+ state. All the oxidation and reduction results and the associated changes in majority carrier concentrations and type conversions can be understood in terms of oxygem/In/sub Cu/-defect interactions

Photoemission spectroscopy study on interfacial energy level alignments in tandem organic light-emitting diodes

Energy Technology Data Exchange (ETDEWEB)

Ou, Qing-Dong; Li, Chi; Li, Yan-Qing, E-mail: yqli@suda.edu.cn; Tang, Jian-Xin, E-mail: jxtang@suda.edu.cn

2015-10-01

Highlights: • The interface energetics of tandem OLEDs is overviewed. • Energy level alignment in CGLs is addressed via photoemission spectroscopy. • The n-type doping effect with cesium compounds is discussed. • Hole injection barrier is dependent on oxygen vacancies in transition metal oxides. • Device lifetime of tandem OLEDs is sensitive to interfacial stability of CGLs. - Abstract: Organic light-emitting diodes (OLEDs) using a tandem structure offer a highly attractive option for the applications of next-generation flat panel displays and solid-state lighting due to the extremely high brightness and efficiency along with the long operational lifetime. In general, reliable information about interface energetics of the charge generation layers (CGLs), which plays the central role in charge generation and carrier injection into the stacked emission units, is highly desirable and advantageous for interface engineering and the performance optimization of tandem OLEDs. In this review, our recent studies on tandem OLEDs are overviewed, especially from interface energetics perspective via photoemission spectroscopy. The electronic structures of various transition metal oxide (TMO)-based CGLs and their role in charge generation process are reviewed, addressing the n-type doping impact of organic layers in CGLs, thermal annealing-induced oxygen vacancy in TMOs, and the interfacial stability of CGLs on the device operational lifetime. The resulting energy level alignments are summarized in correspondence with tandem OLED performance.

Electron Band Alignment at Interfaces of Semiconductors with Insulating Oxides: An Internal Photoemission Study

Directory of Open Access Journals (Sweden)

Valeri V. Afanas'ev

2014-01-01

Full Text Available Evolution of the electron energy band alignment at interfaces between different semiconductors and wide-gap oxide insulators is examined using the internal photoemission spectroscopy, which is based on observations of optically-induced electron (or hole transitions across the semiconductor/insulator barrier. Interfaces of various semiconductors ranging from the conventional silicon to the high-mobility Ge-based (Ge, Si1-xGex, Ge1-xSnx and AIIIBV group (GaAs, InxGa1-xAs, InAs, GaP, InP, GaSb, InSb materials were studied revealing several general trends in the evolution of band offsets. It is found that in the oxides of metals with cation radii larger than ≈0.7 Å, the oxide valence band top remains nearly at the same energy (±0.2 eV irrespective of the cation sort. Using this result, it becomes possible to predict the interface band alignment between oxides and semiconductors as well as between dissimilar insulating oxides on the basis of the oxide bandgap width which are also affected by crystallization. By contrast, oxides of light elements, for example, Be, Mg, Al, Si, and Sc exhibit significant shifts of the valence band top. General trends in band lineup variations caused by a change in the composition of semiconductor photoemission material are also revealed.

Spin-resolved photoemission of surface states of W(110)-(1x1)H

International Nuclear Information System (INIS)

Hochstrasser, M.; Tobin, J.G.; Rotenberg, Eli; Kevan, S.D.

2002-01-01

The surface electronic states of W(110)-(1x1)H have been measured using spin- and angle-resolved photoemission. We directly demonstrate that the surface bands are both split and spin-polarized by the spin-orbit interaction in association with the loss of inversion symmetry near a surface. We observe 100 percent spin polarization of the surface states, with the spins aligned in the plane of the surface and oriented in a circular fashion relative to the S-bar symmetry point. In contrast, no measurable polarization of nearby bulk states is observed

Studies on a laser driven photoemissive high-brightness electron source and novel photocathodes

International Nuclear Information System (INIS)

Geng Rongli; Song Jinhu; Yu Jin

1997-01-01

A laser driven photoemissive high-brightness electron source at Beijing University is reported. Through a DC accelerating gap of 100 kV voltage, the device is capable of delivering high-brightness electron beam of 35-100 ps pulse duration when irradiated with a mode-locked YAG laser. The geometry of the gun is optimized with the aid of simulation codes EGUN and POISSON. The results of experimental studies on ion implanted photocathode and cesium telluride photocathode are given. The proposed laser driven superconducting RF gun is also discussed

Determination of electronic states in crystalline semiconductors and metals by angle-resolved photoemission

International Nuclear Information System (INIS)

Mills, K.A.

1979-08-01

An important part of the theoretical description of the solid state is band structure, which relies on the existence of dispersion relations connecting the electronic energy and wavevector in materials with translational symmetry. These relations determine the electronic behavior of such materials. The elaboration of accurate band structures, therefore, is of considerable fundamental and practical importance. Angle-resolved photoemission (ARP) spectroscopy provides the only presently available method for the detailed experimental investigation of band structures. This work is concerned with its application to both semiconducting and metallic single crystals

Design and optimization of high-performance slot-microring Si-photodetector based on internal photoemission effect

Science.gov (United States)

Hosseinifar, Mitra; Ahmadi, Vahid; Ebnali-Heidari, Majid

2017-08-01

This paper presents the design and optimization of a microring resonator enhanced-internal photoemission effect-photodetectors (MRRE-IPE-PDs) suitable for optical communication. Two PD configurations are considered: the first consists of an MRR that is partially surrounded by a nanolayer of silicide with a single Schottky barrier on p-Si MRR; and the second consists of a silicide film buried in the width midpoints of a Si-based MRR where photoemission occurs over the two Schottky barriers. Several silicides are considered for the stripe (PtSi, Pd2Si, TaSi2 and CoSi2). The important features of the device, such as quantum efficiency (QE), responsivity, CW sensitivity and dark current are discussed and the trade-off between 3 dB bandwidth and QE are analyzed for nanoscaled absorption layer. In this regard, some design curves are presented for the optimized MRRE-IPE-PDs. Additionally, this paper reveals substantial improvement via comparisons with QE and responsivity measurements reported in the literature. Bandwidth-efficiency product of 61-71 GHz, responsivities of 0.8-0.9 and QE of 64-71% and the minimum receiver sensitivity of -65 to -66 dBm are also predicted for single and double Schottky barriers, respectively.

Synchrotron radiation photoemission spectrum study on K3C60 film

Institute of Scientific and Technical Information of China (English)

李宏年; 徐亚伯; 鲍世宁; 李海洋; 何丕模; 钱海杰; 刘风琴; 奎热西·易卜拉欣

2000-01-01

K3C60 single crystal film was prepared on the cleaved (111) surface of C60 single crystal. Synchrotron radiation angle-resolved photoemission spectra were measured at normal emission with sample temperature at - 150K. Up to four subpeaks of LUMO-derived band were observed. These sub-peaks exhibit distinct energy dispersions which resemble in general the theoretical ones calculated for K3C60 at low temperature with the so-called one-dimensional disordered structure. But there is large deviation of experimental sub-band intervals from the theoretical values. This result is meaningful for the studies of the physical properties of alkali-doped C60 solids, e.g. the mechanism for superconductivity.

Short-period oscillations in photoemission from thin films of Cr(100)

Science.gov (United States)

Vyalikh, Denis V.; Zahn, Peter; Richter, Manuel; Dedkov, Yu. S.; Molodtsov, S. L.

2005-07-01

Angle-resolved photoemission (PE) study of thin films of Cr grown on Fe(100) reveals thickness-dependent short-period oscillations of the PE intensity close to the Fermi energy at k‖˜0 . The oscillations are assigned to quantum-well states (QWS) caused by the nesting between the Fermi-surface sheets around the Γ and the X points in the Brillouin zone of antiferromagnetic Cr. The experimental data are confirmed by density-functional calculations applying a screened Korringa-Kohn-Rostoker Green’s function method. The period of the experimentally observed QWS oscillations amounts to about 2.6 monolayers and is larger than the fundamental 2-monolayer period of antiferromagnetic coupling in Cr.

Aberration correction in photoemission microscopy and applications in photonics and plasmonics

Energy Technology Data Exchange (ETDEWEB)

Koenenkamp, Rolf [Portland State Univ., Portland, OR (United States)

2017-09-28

We report on the design, assembly, operation and application of an aberration-corrected photoemission electron microscope. The instrument used novel hyperbolic mirror-correctors with two and three electrodes that allowed simultaneous correction of spherical and chromatic aberrations. A spatial resolution of 5.4nm was obtained with this instrument in 2009, and 4.7nm in subsequent years. New imaging methodology was introduced involving interferometric imaging of light diffraction. This methodology was applied in nano-photonics and in the characterization of surface-plasmon polaritons. Photonic crystals and waveguides, optical antennas and new plasmonic devices such as routers, localizers and filters were designed and demonstrated using the new capabilities offered by the microscope.

An ultrafast electron microscope gun driven by two-photon photoemission from a nanotip cathode

International Nuclear Information System (INIS)

Bormann, Reiner; Strauch, Stefanie; Schäfer, Sascha; Ropers, Claus

2015-01-01

We experimentally and numerically investigate the performance of an advanced ultrafast electron source, based on two-photon photoemission from a tungsten needle cathode incorporated in an electron microscope gun geometry. Emission properties are characterized as a function of the electrostatic gun settings, and operating conditions leading to laser-triggered electron beams of very low emittance (below 20 nm mrad) are identified. The results highlight the excellent suitability of optically driven nano-cathodes for the further development of ultrafast transmission electron microscopy

a Study on SODIUM(110) and Other Nearly Free Electron Metals Using Angle Resolved Photoemission Spectroscopy.

Science.gov (United States)

Lyo, In-Whan

Electronic properties of the epitaxially grown Na(110) film have been studied using angle resolved ultraviolet photoemission spectroscopy with synchrotron radiation as the light source. Na provides an ideal ground to study the fundamental aspects of the electron-electron interactions in metals, because of its simple Fermi surface and small pseudopotential. The absolute band structure of Na(110) using angle resolved photoemission spectroscopy has been mapped out using the extrema searching method. The advantage of this approach is that the usual assumption of the unoccupied state dispersion is not required. We have found that the dispersion of Na(1l0) is very close to the parabolic band with the effective mass 1.21 M_{rm e} at 90 K. Self-consistent calculations of the self-energy for the homogeneous electron gas have been performed using the Green's function technique within the framework of the GW approximation, in the hope of understanding the narrowing mechanism of the bandwidth observed for all the nearly-free-electron (NFE) metals. Good agreements between the experimental data and our calculated self-energy were obtained not only for our data on k-dependency from Na(l10), but also for the total bandwidth corrections for other NFE metals, only if dielectric functions beyond the random phase approximation were used. Our findings emphasize the importance of the screening by long wavelength plasmons. Off-normal spectra of angle resolved photoemission from Na(110) show strong asymmetry of the bulk peak intensity for the wide range of photon energies. Using a simple analysis, we show this asymmetry has an origin in the interference of the surface Umklapp electrons with the normal electrons. We have also performed the detailed experimental studies of the anomalous Fermi level structure observed in the forbidden gap region of Na. This was claimed by A. W. Overhauser as the evidence of the charge density wave in the alkali metal. The possibility of this hypothesis is

Photoemission studies using laboratory and synchrotron sources

International Nuclear Information System (INIS)

Phase, D.M.

2012-01-01

Synchrotron radiation sources, providing intense, polarized and stable beams of ultra violet soft and hard X-ray photons, are having great impact on physics, chemistry, biology materials science and other areas research. In particular synchrotron radiation has revolutionized photoelectron spectroscopy by enhancing its capabilities for investigating the electronic properties of solids. The first Indian synchrotron storage ring, Indus- 1 is in operation at RRCAT, Indore. The UGC-DAE CSR with the help of university scientist had designed and developed an angle integrated photoelectron spectroscopy (PES) beamline on this 450 MeV storage ring. A storage ring of this kind is most suitable for investigation in the energy range from few electron volts to around five hundred electron volts. In this lecture we will describe the details of PES beamline and its experimental station. Till date the different university users carried out photoemission measurements on variety of samples. Some of the spectra recorded by users will be presented in order to show the capability of this beamline. In the later part we will report a review of our recent research work carried out on dilute magnetic thin films using this beamline. (author)

A study of angle-resolved photoemission extended fine structure as applied to the Ni 3p, Cu 3s, and Cu 3p core levels of the respective clean (111) surfaces

Energy Technology Data Exchange (ETDEWEB)

Huff, W.R.A.; Moler, E.J.; Kellar, S.A. [Lawrence Berkeley National Lab., CA (United States)] [and others

1997-04-01

The first non-s initial state angle-resolved photoemission extended fine structure (ARPEFS) study of clean surfaces for the purpose of further understanding the technique is reported. The surface structure sensitivity of ARPEFS applied to clean surfaces and to arbitrary initial states is studied using normal photoemission data taken from the Ni 3p core levels of a Ni(111) single crystal and the Cu 3s and the Cu 3p core-levels of a Cu(111) single crystal. The Fourier transforms of these clean surface data are dominated by backscattering. Unlike the s initial state data, the p initial state data show a peak in the Fourier transform corresponding to in-plane scattering from the six nearest-neighbors to the emitter. Evidence was seen for single-scattering events from in the same plane as the emitters and double-scattering events. Using a newly developed, multiple-scattering calculation program, ARPEFS data from clean surfaces and from p initial states can be modeled to high precision. Although there are many layers of emitters when measuring photoemission from a clean surface, test calculations show that the ARPEFS signal is dominated by photoemission from atoms in the first two crystal layers. Thus, ARPEFS applied to clean surfaces is sensitive to surface reconstruction. The known contraction of the first two Cu(111) layers is confirmed. The best-fit calculation for clean Ni(111) indicates an expansion of the first two layers. To better understand the ARPEFS technique, the authors studied s and non-s initial state photoemission from clean metal surfaces.

An ultrafast angle-resolved photoemission apparatus for measuring complex materials

International Nuclear Information System (INIS)

Smallwood, Christopher L.; Lanzara, Alessandra; Jozwiak, Christopher; Zhang Wentao

2012-01-01

We present technical specifications for a high resolution time- and angle-resolved photoemission spectroscopy setup based on a hemispherical electron analyzer and cavity-dumped solid state Ti:sapphire laser used to generate pump and probe beams, respectively, at 1.48 and 5.93 eV. The pulse repetition rate can be tuned from 209 Hz to 54.3 MHz. Under typical operating settings the system has an overall energy resolution of 23 meV, an overall momentum resolution of 0.003 Å −1 , and an overall time resolution of 310 fs. We illustrate the system capabilities with representative data on the cuprate superconductor Bi 2 Sr 2 CaCu 2 O 8+δ . The descriptions and analyses presented here will inform new developments in ultrafast electron spectroscopy.

A new approach for 3D reconstruction from bright field TEM imaging: Beam precession assisted electron tomography

Energy Technology Data Exchange (ETDEWEB)

Rebled, J.M. [LENS-MIND-IN2UB, Departament d' Electronica, Universitat de Barcelona, Marti i Franques 1, 08028 Barcelona (Spain); Institut de Ciencia de Materials de Barcelona-CSIC, Campus UAB, 08193 Bellaterra (Spain); Yedra, Ll. [LENS-MIND-IN2UB, Departament d' Electronica, Universitat de Barcelona, Marti i Franques 1, 08028 Barcelona (Spain); Estrade, S.; Portillo, J. [LENS-MIND-IN2UB, Departament d' Electronica, Universitat de Barcelona, Marti i Franques 1, 08028 Barcelona (Spain); TEM-MAT, CCiT-UB, Sole i Sabaris 1, 08028 Barcelona (Spain); Peiro, F., E-mail: francesca.peiro@ub.edu [LENS-MIND-IN2UB, Departament d' Electronica, Universitat de Barcelona, Marti i Franques 1, 08028 Barcelona (Spain)

2011-08-15

The successful combination of electron beam precession and bright field electron tomography for 3D reconstruction is reported. Beam precession is demonstrated to be a powerful technique to reduce the contrast artifacts due to diffraction and curvature in thin foils. Taking advantage of these benefits, Precession assisted electron tomography has been applied to reconstruct the morphology of Sn precipitates embedded in an Al matrix, from a tilt series acquired in a range from +49{sup o} to -61{sup o} at intervals of 2{sup o} and with a precession angle of 0.6{sup o} in bright field mode. The combination of electron tomography and beam precession in conventional TEM mode is proposed as an alternative procedure to obtain 3D reconstructions of nano-objects without a scanning system or a high angle annular dark field detector. -- Highlights: {yields} Electron beam precession reduces spurious diffraction contrast in bright field mode. {yields} Bend contour related contrast depends on precession angle. {yields} Electron beam precession is combined with bright field electron tomography. {yields} Precession assisted BF tomography allowed 3D reconstruction of a Sn precipitate.

Charge-density-wave partial gap opening in quasi-2D KMo6O17 purple bronze studied by angle resolved photoemission spectroscopy

International Nuclear Information System (INIS)

Valbuena, M.A.; Avila, J.; Pantin, V.; Drouard, S.; Guyot, H.; Asensio, M.C.

2006-01-01

Low dimensional (LD) metallic oxides have been a subject of continuous interest in the last two decades, mainly due to the electronic instabilities that they present at low temperatures. In particular, charge density waves (CDW) instabilities associated with a strong electron-phonon interaction have been found in Molybdenum metallic oxides such as KMo 6 O 17 purple bronze. We report an angle resolved photoemission (ARPES) study from room temperature (RT) to T ∼40 K well below the Peierls transition temperature for this material, with CDW transition temperature T CDW ∼120 K. We have focused on photoemission spectra along ΓM high symmetry direction as well as photoemission measurements were taken as a function of temperature at one representative k F point in the Brillouin zone in order to look for the characteristic gap opening after the phase transition. We found out a pseudogap opening and a decrease in the density of states near the Fermi energy, E F , consistent with the partial removal of the nested portions of the Fermi surface (FS) at temperature below the CDW transition. In order to elucidate possible Fermi liquid (FL) or non-Fermi liquid (NFL) behaviour we have compared the ARPES data with that one reported on quasi-1D K 0.3 MoO 3 blue bronze

Phonon-assisted field emission in silicon nanomembranes for time-of-flight mass spectrometry of proteins.

Science.gov (United States)

Park, Jonghoo; Aksamija, Zlatan; Shin, Hyun-Cheol; Kim, Hyunseok; Blick, Robert H

2013-06-12

Time-of-flight (TOF) mass spectrometry has been considered as the method of choice for mass analysis of large intact biomolecules, which are ionized in low charge states by matrix-assisted-laser-desorption/ionization (MALDI). However, it remains predominantly restricted to the mass analysis of biomolecules with a mass below about 50,000 Da. This limitation mainly stems from the fact that the sensitivity of the standard detectors decreases with increasing ion mass. We describe here a new principle for ion detection in TOF mass spectrometry, which is based upon suspended silicon nanomembranes. Impinging ion packets on one side of the suspended silicon nanomembrane generate nonequilibrium phonons, which propagate quasi-diffusively and deliver thermal energy to electrons within the silicon nanomembrane. This enhances electron emission from the nanomembrane surface with an electric field applied to it. The nonequilibrium phonon-assisted field emission in the suspended nanomembrane connected to an effective cooling of the nanomembrane via field emission allows mass analysis of megadalton ions with high mass resolution at room temperature. The high resolution of the detector will give better insight into high mass proteins and their functions.

Effect of magnetic polarity on surface roughness during magnetic field assisted EDM of tool steel

Science.gov (United States)

Efendee, A. M.; Saifuldin, M.; Gebremariam, MA; Azhari, A.

2018-04-01

Electrical discharge machining (EDM) is one of the non-traditional machining techniques where the process offers wide range of parameters manipulation and machining applications. However, surface roughness, material removal rate, electrode wear and operation costs were among the topmost issue within this technique. Alteration of magnetic device around machining area offers exciting output to be investigated and the effects of magnetic polarity on EDM remain unacquainted. The aim of this research is to investigate the effect of magnetic polarity on surface roughness during magnetic field assisted electrical discharge machining (MFAEDM) on tool steel material (AISI 420 mod.) using graphite electrode. A Magnet with a force of 18 Tesla was applied to the EDM process at selected parameters. The sparks under magnetic field assisted EDM produced better surface finish than the normal conventional EDM process. At the presence of high magnetic field, the spark produced was squeezed and discharge craters generated on the machined surface was tiny and shallow. Correct magnetic polarity combination of MFAEDM process is highly useful to attain a high efficiency machining and improved quality of surface finish to meet the demand of modern industrial applications.

Common Features in Electronic Structure of the Oxypnictide Superconductors from Photoemission Spectroscopy

International Nuclear Information System (INIS)

Xiao-Wen, Jia; Hai-Yun, Liu; Wen-Tao, Zhang; Lin, Zhao; Jian-Qiao, Meng; Guo-Dong, Liu; Xiao-Li, Dong; Zhi-An, Ren; Wei, Yi; Guang-Can, Che; Zhong-Xian, Zhao; Gang, Wu; Rong-Hua, Liu; Xian-Hui, Chen; Gen-Fu, Chen; Nan-Lin, Wang; Yong, Zhu; Xiao-Yang, Wang; Gui-Ling, Wang; Yong, Zhou

2008-01-01

High resolution photoemission measurements are carried out on non-superconducting LaFeAsO parent compound and various superconducting RFeAs(O 1-x F x ) (R=La, Ce and Pr) compounds. It is found that the parent LaFeAsO compound shows a metallic character. By extensive measurements, several common features are identified in the electronic structure of these Fe-based compounds: (1) 0.2 eV feature in the valence band, (2) a universal 13-16 meV feature, (3) near Ef spectral weight suppression with decreasing temperature. These universal features can provide important information about band structure, superconducting gap and pseudogap in these Fe-based materials

A photoemission study of interfaces between organic semiconductors and Co as well as Al2O3/Co contacts

NARCIS (Netherlands)

Grobosch, M.; Schmidt, C.; Naber, W.J.M.; van der Wiel, Wilfred Gerard; Knupfer, M.

We have studied the energy-level alignment of ex situ, acetone cleaned Co and Al2O3/Co contacts to the organic semiconductors pentacene and rubrene by combined X-ray and ultraviolet photoemission spectroscopy. Our results demonstrate that the work function under these conditions is smaller than in

Development of soft x-ray time-resolved photoemission spectroscopy system with a two-dimensional angle-resolved time-of-flight analyzer at SPring-8 BL07LSU

Energy Technology Data Exchange (ETDEWEB)

Ogawa, Manami; Yamamoto, Susumu; Nakamura, Fumitaka; Yukawa, Ryu; Fukushima, Akiko; Harasawa, Ayumi; Kakizaki, Akito; Matsuda, Iwao [Institute for Solid State Physics, University of Tokyo, 5-1-5 Kashiwanoha, Chiba 277-8581 (Japan); Kousa, Yuka; Kondoh, Hiroshi [Department of Chemistry, Keio University, Yokohama 223-8522 (Japan); Tanaka, Yoshihito [RIKEN/SPring-8 Center, 1-1-1, Kouto, Sayo-cho, Sayo-gun, Hyogo 679-5148 (Japan)

2012-02-15

We have developed a soft x-ray time-resolved photoemission spectroscopy system using synchrotron radiation (SR) at SPring-8 BL07LSU and an ultrashort pulse laser system. Two-dimensional angle-resolved measurements were performed with a time-of-flight-type analyzer. The photoemission spectroscopy system is synchronized to light pulses of SR and laser using a time control unit. The performance of the instrument is demonstrated by mapping the band structure of a Si(111) crystal over the surface Brillouin zones and observing relaxation of the surface photo-voltage effect using the pump (laser) and probe (SR) method.

An experimentalist's guide to the matrix element in angle resolved photoemission

International Nuclear Information System (INIS)

Moser, Simon

2017-01-01

Highlights: • An introduction to the art of angle resolved photoemission is presented. • Matrix element effects are described by a nearly free electron final state model. • ARPES spectral weight of a Bloch band can be calculated from the Fourier transform of its Wannier orbital. • Experimental handedness and improper polarization introduce dichroism. • Instructive showcases from modern ARPES are discussed in detail. - Abstract: Angle resolved photoemission spectroscopy (ARPES) is commonly known as a powerful probe of the one-electron removal spectral function in ordered solid state. With increasing efficiency of light sources and spectrometers, experiments over a wide range of emission angles become more and more common. Consequently, the angular variation of ARPES spectral weight – often times termed “matrix element effect” – enters as an additional source of information. In this tutorial, we develop a simple but instructive free electron final state approach based on the three-step model to describe the intensity distribution in ARPES. We find a compact expression showing that the ARPES spectral weight of a given Bloch band is essentially determined by the momentum distribution (the Fourier transform) of its associated Wannier orbital – times a polarization dependent pre-factor. While the former is giving direct information on the symmetry and shape of the electronic wave function, the latter can give rise to surprising geometric effects. We discuss a variety of modern and instructive experimental showcases for which this simplistic formalism works astonishingly well and discuss the limits of this approach.

Magnetic dichroism in photoemission: a new element-specific magnetometer with atomic-layer resolution

International Nuclear Information System (INIS)

Starke, K.; Arenholz, E.; Kaindl, G.

1998-01-01

Full text: Magnetic coupling in layered metallic structures has become a key issue in thin-film magnetism since the observation of oscillatory exchange coupling across non-ferromagnetic spacer layers. Although this phenomenon was discovered in rare earths (RE) superlattices, mostly transition-metal systems have been studied and are now applied in data-storage industry. An understanding of the coupling mechanisms has been reached after a fabrication of high-quality interfaces became possible. It allowed, in particular, the experimental finding of induced ferromagnetic order in 'nonmagnetic' atomic layers near an interface, using element-specific probes such as magnetic circular dichroism in x-ray absorption. - In layered RE systems, by contrast, the well known intermiscibility has prevented a preparation of atomically sharp interfaces, and all RE superlattices studied so far showed interdiffusion zones of several atomic layers. In the present overview, we report the first fabrication of atomically flat heteromagnetic RE interfaces, their structural characterization and their magnetic analysis using magnetic dichroism in photoemission (MDPE). This new tool gives access to the magnetization of individual atomic layers near interfaces in favourite cases. Merits of MDPE as a magnetometer are demonstrated at the example of Eu/Gd(0001), where chemical shifts of core-level photoemission lines allow to spectroscopically separate up to four different atomic layers. The high surface sensitivity of MDPE, together with the well known dependence of the core-level binding energies on the coordination number of the photo emitting atom, opens the door to future site-specific studies of magnetism in sub-monolayer systems such as 'nanowires'

An experimentalist's guide to the matrix element in angle resolved photoemission

Energy Technology Data Exchange (ETDEWEB)

Moser, Simon, E-mail: skmoser@lbl.gov [Advanced Light Source (ALS), Berkeley, CA 94720 (United States); Institute of Physics (IPHYS), Ecole Polytechnique Fédérale de Lausanne (EPFL), CH-1015 Lausanne (Switzerland)

2017-01-15

Highlights: • An introduction to the art of angle resolved photoemission is presented. • Matrix element effects are described by a nearly free electron final state model. • ARPES spectral weight of a Bloch band can be calculated from the Fourier transform of its Wannier orbital. • Experimental handedness and improper polarization introduce dichroism. • Instructive showcases from modern ARPES are discussed in detail. - Abstract: Angle resolved photoemission spectroscopy (ARPES) is commonly known as a powerful probe of the one-electron removal spectral function in ordered solid state. With increasing efficiency of light sources and spectrometers, experiments over a wide range of emission angles become more and more common. Consequently, the angular variation of ARPES spectral weight – often times termed “matrix element effect” – enters as an additional source of information. In this tutorial, we develop a simple but instructive free electron final state approach based on the three-step model to describe the intensity distribution in ARPES. We find a compact expression showing that the ARPES spectral weight of a given Bloch band is essentially determined by the momentum distribution (the Fourier transform) of its associated Wannier orbital – times a polarization dependent pre-factor. While the former is giving direct information on the symmetry and shape of the electronic wave function, the latter can give rise to surprising geometric effects. We discuss a variety of modern and instructive experimental showcases for which this simplistic formalism works astonishingly well and discuss the limits of this approach.

Improving the performance of nickel-coated fluorine-doped tin oxide thin films by magnetic-field-assisted laser annealing

Energy Technology Data Exchange (ETDEWEB)

Li, Bao-jia, E-mail: li_bjia@126.com [School of Materials Science and Engineering, Jiangsu University, Zhenjiang 212013 (China); Jiangsu Provincial Key Laboratory of Center for Photon Manufacturing Science and Technology, Jiangsu University, Zhenjiang 212013 (China); Huang, Li-jing [School of Materials Science and Engineering, Jiangsu University, Zhenjiang 212013 (China); Jiangsu Provincial Key Laboratory of Center for Photon Manufacturing Science and Technology, Jiangsu University, Zhenjiang 212013 (China); Ren, Nai-fei [Jiangsu Provincial Key Laboratory of Center for Photon Manufacturing Science and Technology, Jiangsu University, Zhenjiang 212013 (China); School of Mechanical Engineering, Jiangsu University, Zhenjiang 212013 (China); Kong, Xia; Cai, Yun-long; Zhang, Jie-lu [Jiangsu Tailong Reduction Box Co. Ltd., Taixing 225400 (China)

2015-10-01

Highlights: • Ni/FTO films were prepared by sputtering Ni layers on commercial FTO glass. • The as-prepared Ni/FTO films underwent magnetic-field-assisted laser annealing. • Magnetic field and laser fluence were crucial for improving quality of the films. • All Ni/FTO films displayed enhanced compactness after magnetic laser annealing. • Magnetic laser annealing using a fluence of 0.9 J/cm{sup 2} led to the best film quality. - Abstract: Nickel-coated fluorine-doped tin oxide (Ni/FTO) thin films were prepared by sputtering Ni layers on commercial FTO glass. The as-prepared Ni/FTO films underwent nanosecond pulsed laser annealing in an external magnetic field (0.4 T). The effects of the presence of magnetic field and laser fluence on surface morphology, crystal structure and photoelectric properties of the films were investigated. All the films displayed enhanced compactness after magnetic-field-assisted laser annealing. It was notable that both crystallinity and grain size of the films gradually increased with increasing laser fluence from 0.6 to 0.9 J/cm{sup 2}, and then decreased slightly with an increase in laser fluence to 1.1 J/cm{sup 2}. As a result, the film obtained by magnetic-field-assisted laser annealing using a fluence of 0.9 J/cm{sup 2} had the best overall photoelectric property with an average transmittance of 81.2%, a sheet resistance of 5.5 Ω/sq and a figure of merit of 2.27 × 10{sup −2} Ω{sup −1}, outperforming that of the film obtained by pure laser annealing using the same fluence.

Vacancy formation in MoO3: hybrid density functional theory and photoemission experiments

KAUST Repository

Salawu, Omotayo Akande

2016-09-29

Molybdenum oxide (MoO3) is an important material that is being considered for numerous technological applications, including catalysis and electrochromism. In the present study, we apply hybrid density functional theory to investigate O and Mo vacancies in the orthorhombic phase. We determine the vacancy formation energies of different defect sites as functions of the electron chemical potential, addressing different charge states. In addition, we investigate the consequences of defects for the material properties. Ultraviolet photoemission spectroscopy is employed to study the valence band of stoichiometric and O defective MoO3. We show that O vacancies result in occupied in-gap states.

Electronic structure of superconducting Bi2212 crystal by angle resolved ultra violet photoemission

International Nuclear Information System (INIS)

Saini, N.L.; Shrivastava, P.; Garg, K.B.

1993-01-01

The electronic structure of a high quality superconducting Bi 2 Sr 2 CaCu 2 Osub(8+δ) (Bi2212) single crystal is studied by angle resolved ultra violet photoemission (ARUPS) using He I (21.2 eV). Our results appear to show two bands crossing the Fermi level in ΓX direction of the Brillouin zone as reported by Takahashi et al. The bands at higher binding energy do not show any appreciable dispersion. The nature of the states near the Fermi level is discussed and the observed band structure is compared with the band structure calculations. (author)

Vacancy formation in MoO3: hybrid density functional theory and photoemission experiments

KAUST Repository

Salawu, Omotayo Akande; Chroneos, Alexander; Vasilopoulou, Maria; Kennou, Stella; Schwingenschlö gl, Udo

2016-01-01

Molybdenum oxide (MoO3) is an important material that is being considered for numerous technological applications, including catalysis and electrochromism. In the present study, we apply hybrid density functional theory to investigate O and Mo vacancies in the orthorhombic phase. We determine the vacancy formation energies of different defect sites as functions of the electron chemical potential, addressing different charge states. In addition, we investigate the consequences of defects for the material properties. Ultraviolet photoemission spectroscopy is employed to study the valence band of stoichiometric and O defective MoO3. We show that O vacancies result in occupied in-gap states.

Local Electronic and Magnetic Structure of Ni below and above TC: A Spin-Resolved Circularly Polarized Resonant Photoemission Study

NARCIS (Netherlands)

Sinkovic, B.; Tjeng, L.H.; Brookes, N.B.; Goedkoop, J.B.; Hesper, R.; Pellegrin, E.; Groot, F.M.F. de; Altieri, S.; Hulbert, S.L.; Shekel, E.; Sawatzky, G.A.

1997-01-01

We report the measurement of the local Ni 3d spin polarization, not only below but also above the Curie temperature (TC), using the newly developed spin-resolved circularly polarized 2p (L3) resonant photoemission technique. The experiment identifies the presence of 3d8 singlets at high energies

Temperature dependence of high-resolution resonant photoemission spectra of CeSi

International Nuclear Information System (INIS)

Mimura, Kojiro; Noguchi, Satoru; Suzuki, Mitsuharu; Higashiguchi, Mitsuharu; Shimada, Kenya; Ichikawa, Kouichi; Taguchi, Yukihiro; Namatame, Hirofumi; Taniguchi, Masaki; Aita, Osamu

2005-01-01

High-resolution Ce 4d-4f resonant photoemission spectra near the Fermi level of CeSi with the Neel temperature of 5.9K have been measured at temperatures from 5.6 to 200K, in order to investigate the competition between the Ruderman-Kittel-Kasuya-Yoshida (RKKY) interaction and the Kondo effect. As temperature is decreasing down to 30K, the intensity due to the Ce 4f 5/2 1 final state increases because of the evolution of the heavy Fermion behaviour caused by the Kondo effect. The intensity, however, decreases gradually from 30 to 5.6K. This indicates that the heavy Fermion behaviour is strongly suppressed by the anti-ferromagnetic ordering due to the RKKY interaction

Structural and mechanical properties of hydroxyapatite coatings formed by ion-beam assisted deposition

Science.gov (United States)

Zykova, A.; Safonov, V.; Dudin, S.; Yakovin, S.; Donkov, N.; Ghaemi, M. H.; Szkodo, M.; Antoszkiewicz, M.; Szyfelbain, M.; Czaban, A.

2018-03-01

The ion-beam assisted deposition (IBAD) is an advanced method capable of producing crystalline coatings at low temperatures. We determined the characteristics of hydroxyapatite Ca10(PO4)6(OH)2 target and coatings formed by IBAD using X-ray photoemission spectroscopy (XPS), X-ray diffraction (XRD), scanning electron microscopy (SEM), atomic force microscopy (AFM) and energy dispersive X-ray (EDX). The composition of the coatings’ cross-section and surface was close to those of the target. The XPS spectra showed that the binding energy values of Ca (2p1/2, 2p3/2), P (2p3/2), and O 1s levels are related to the hydroxyapatite phase. The coatings demonstrate an optimal H/E ratio, and a good resistance to scratch tests.

Microlens Array Laser Transverse Shaping Technique for Photoemission Electron Source

Energy Technology Data Exchange (ETDEWEB)

Halavanau, A. [Northern Illinois Univ., DeKalb, IL (United States); Fermi National Accelerator Lab. (FNAL), Batavia, IL (United States); Ha, G. [Argonne National Lab. (ANL), Argonne, IL (United States); Pohang Univ. of Science and Technology (POSTECH) (Korea, Republic of); Qiang, G. [Argonne National Lab. (ANL), Argonne, IL (United States); Tsinghua Univ., Beijing (China); Gai, W. [Argonne National Lab. (ANL), Argonne, IL (United States); Power, J. [Argonne National Lab. (ANL), Argonne, IL (United States); Piot, P. [Northern Illinois Univ., DeKalb, IL (United States); Fermi National Accelerator Lab. (FNAL), Batavia, IL (United States); Wisniewski, E. [Argonne National Lab. (ANL), Argonne, IL (United States); Edstrom, D. [Fermi National Accelerator Lab. (FNAL), Batavia, IL (United States); Ruan, J. [Fermi National Accelerator Lab. (FNAL), Batavia, IL (United States); Santucci, J. [Fermi National Accelerator Lab. (FNAL), Batavia, IL (United States)

2016-09-06

A common issue encountered in photoemission electron sources used in electron accelerators is distortion of the laser spot due to non ideal conditions at all stages of the amplification. Such a laser spot at the cathode may produce asymmetric charged beams that will result in degradation of the beam quality due to space charge at early stages of acceleration and fail to optimally utilize the cathode surface. In this note we study the possibility of using microlens arrays to dramatically improve the transverse uniformity of the drive laser pulse on UV photocathodes at both Fermilab Accelerator Science \\& Technology (FAST) facility and Argonne Wakefield Accelerator (AWA). In particular, we discuss the experimental characterization of the homogeneity and periodic patterned formation at the photocathode. Finally, we compare the experimental results with the paraxial analysis, ray tracing and wavefront propagation software.

Molecular frame photoelectron angular distribution for oxygen 1s photoemission from CO2 molecules

International Nuclear Information System (INIS)

Saito, N; Ueda, K; De Fanis, A

2005-01-01

We have measured photoelectron angular distributions in the molecular frame (MF-PADs) for O 1s photoemission from CO 2 , using photoelectron-O + -CO + coincidence momentum imaging. Results for the molecular axis at 0, 45 and 90 0 to the electric vector of the light are reported. The major features of the MF-PADs are fairly well reproduced by calculations employing a relaxed-core Hartree-Fock approach. Weak asymmetric features are seen through a plane perpendicular to the molecular axis and attributed to symmetry lowering by anti-symmetric stretching motion. (letter to the editor)

Establishment of a nanoparticle-assisted RT-PCR assay to distinguish field strains and attenuated strains of porcine epidemic diarrhea virus.

Science.gov (United States)

Zhu, Yu; Wang, Gui-Hua; Cui, Yu-Dong; Cui, Shang-Jin

2016-09-01

Porcine epidemic diarrhea virus (PEDV) can cause serious disease and even death in neonatal piglets, resulting in serious damage to the swine industry worldwide. Open reading frame 3 (ORF3) is the only accessory gene in the PEDV genome. Previous studies have indicated that PEDV vaccine strains have a partial deletion in ORF3. In this study, a nanoparticle-assisted polymerase chain reaction (nanoparticle-assisted RT-PCR) assay targeting the ORF3 of PEDV was developed to distinguish PEDV field strains from attenuated strains by using a specific pair of primers. The PCR products of field strains and attenuated strains were 264 bp and 215 bp in length, respectively. The sensitivity and specificity of this assay were also assessed. The nanoparticle-assisted RT-PCR assay was 10-100 times more sensitive than the conventional RT-PCR assay, with no cross-reactions when amplifying porcine pseudorabies virus (PRV), porcine circovirus type 2 (PCV2), classical swine fever virus (CSFV), porcine parvovirus (PPV), porcine reproductive and respiratory syndrome virus (PRRSV), porcine rotavirus (RV), and porcine transmissible gastroenteritis virus (TGEV). The nanoparticle-assisted RT-PCR assay we describe here can be used to distinguish field strains from vaccine strains of PEDV, and it shows promise for reducing economic loss due to PEDV infection.

Electronic structure and core-level spectra of light actinide dioxides in the dynamical mean-field theory

Czech Academy of Sciences Publication Activity Database

Kolorenč, Jindřich; Shick, Alexander; Lichtenstein, A.I.

2015-01-01

Roč. 92, č. 8 (2015), "085125-1"-"085125-10" ISSN 1098-0121 R&D Projects: GA ČR GC15-05872J Institutional support: RVO:68378271 Keywords : electronic-structure calculations * dynamical mean-field theory * Mott insulators * actinides * oxides * photoemission Subject RIV: BM - Solid Matter Physics ; Magnetism Impact factor: 3.736, year: 2014

Band structure and Fermi surface of UPd2Al3 studied by angle-resolved photoemission spectroscopy

International Nuclear Information System (INIS)

Fujimori, Shin-ichi; Saitoh, Yuji; Okane, Tetsuo; Yamagami, Hiroshi; Fujimori, Atsushi; Haga, Yoshinori; Yamamoto, Etsuji; Onuki, Yoshichika

2007-01-01

We have observed the band structure and Fermi surfaces of the heavy Fermion superconductor UPd 2 Al 3 by angle-resolved photoemission experiments in the soft X-ray region. We observed renormalized quasi-particle bands in the vicinity of the Fermi level and strongly dispersive bands on the higher binding energy side. Our observation suggests that the structure previously assigned to contributions from localized states in the U 5f spectrum has strong energy dispersions

Effects of field plot size on prediction accuracy of aboveground biomass in airborne laser scanning-assisted inventories in tropical rain forests of Tanzania.

Science.gov (United States)

Mauya, Ernest William; Hansen, Endre Hofstad; Gobakken, Terje; Bollandsås, Ole Martin; Malimbwi, Rogers Ernest; Næsset, Erik

2015-12-01

Airborne laser scanning (ALS) has recently emerged as a promising tool to acquire auxiliary information for improving aboveground biomass (AGB) estimation in sample-based forest inventories. Under design-based and model-assisted inferential frameworks, the estimation relies on a model that relates the auxiliary ALS metrics to AGB estimated on ground plots. The size of the field plots has been identified as one source of model uncertainty because of the so-called boundary effects which increases with decreasing plot size. Recent research in tropical forests has aimed to quantify the boundary effects on model prediction accuracy, but evidence of the consequences for the final AGB estimates is lacking. In this study we analyzed the effect of field plot size on model prediction accuracy and its implication when used in a model-assisted inferential framework. The results showed that the prediction accuracy of the model improved as the plot size increased. The adjusted R 2 increased from 0.35 to 0.74 while the relative root mean square error decreased from 63.6 to 29.2%. Indicators of boundary effects were identified and confirmed to have significant effects on the model residuals. Variance estimates of model-assisted mean AGB relative to corresponding variance estimates of pure field-based AGB, decreased with increasing plot size in the range from 200 to 3000 m 2 . The variance ratio of field-based estimates relative to model-assisted variance ranged from 1.7 to 7.7. This study showed that the relative improvement in precision of AGB estimation when increasing field-plot size, was greater for an ALS-assisted inventory compared to that of a pure field-based inventory.

Extinction of photoemission of Mn-Doped ZnS nanofluid in weak magnetic field

Science.gov (United States)

Vu, Anh-Tuan; Bui, Hong-Van; Pham, Van-Ben; Le, Van-Hong; Hoang, Nam-Nhat

2016-08-01

The observation of extinction of photoluminescence of Mn-doped ZnS nanofluid under applying of weak magnetic field is reported. At a constant field of 270 Gauss and above, the exponential decays of photoluminescent intensity was observed in disregard of field direction. About 50% extinction was achieved after 30 minute magnetization and a total extinction after 1 hour. The memory effect preserved for more than 2 hours at room temperature. This extinction was observed in a system with no clear ferromagnetic behavior.

Near Field Communication and Health: Turning a Mobile Phone into an Interactive Multipurpose Assistant in Healthcare Scenarios

Science.gov (United States)

Benelli, Giuliano; Pozzebon, Alessandro

In this paper we discuss the introduction of the Near Field Communication (NFC) technology in the management of the assistance operations in the hospitals. NFC is a new short range communication system based on RFID technology.

The interaction of oxygen with TiC(001): Photoemission and first-principles studies

International Nuclear Information System (INIS)

Rodriguez, J.A.; Liu, P.; Dvorak, J.; Jirsak, T.; Gomes, J.; Takahashi, Y.; Nakamura, K.

2004-01-01

High-resolution photoemission and first-principles density-functional slab calculations were used to study the interaction of oxygen with a TiC(001) surface. Atomic oxygen is present on the TiC(001) substrate after small doses of O 2 at room temperature. A big positive shift (1.5-1.8 eV) was detected for the C 1s core level. These photoemission studies suggest the existence of strong O↔C interactions. A phenomenon corroborated by the results of first-principles calculations, which show a CTiTi hollow as the most stable site for the adsorption of O. Ti and C atoms are involved in the adsorption and dissociation of the O 2 molecule. In general, the bond between O and the TiC(001) surface contains a large degree of ionic character. The carbide→O charge transfer is substantial even at high coverages (>0.5 ML) of oxygen. At 500 K and large doses of O 2 , oxidation of the carbide surface occurs with the removal of C and formation of titanium oxides. There is an activation barrier for the exchange of Ti-C and Ti-O bonds which is overcome only by the formation of C-C or C-O bonds on the surface. The mechanism for the removal of a C atom as CO gas involves a minimum of two O adatoms, and three O adatoms are required for the formation of CO 2 gas. Due to the high stability of TiC, an O adatom alone cannot induce the generation of a C vacancy in a flat TiC(001) surface

Metal/silicon Interfaces and Their Oxidation Behavior - Photoemission Spectroscopy Analysis.

Science.gov (United States)

Yeh, Jyh-Jye

Synchrotron radiation photoemission spectroscopy was used to study Ni/Si and Au/Si interface properties on the atomic scale at room temperature, after high temperature annealing and after oxygen exposures. Room temperature studies of metal/Si interfaces provide background for an understanding of the interface structure after elevated temperature annealing. Oxidation studies of Si surfaces covered with metal overlayers yield insight about the effect of metal atoms in the Si oxidation mechanisms and are useful in the identification of subtle differences in bonding relations between atoms at the metal/Si interfaces. Core level and valence band spectra with variable surface sensitivities were used to study the interactions between metal, Si, and oxygen for metal coverages and oxide thickness in the monolayer region. Interface morphology at the initial stage of metal/Si interface formation and after oxidation was modeled on the basis of the evolutions of metal and Si signals at different probing depths in the photoemission experiment. Both Ni/Si and Au/Si interfaces formed at room temperature have a diffusive region at the interface. This is composed of a layer of metal-Si alloy, formed by Si outdiffusion into the metal overlayer, above a layer of interstitial metal atoms in the Si substrate. Different atomic structures of these two regions at Ni/Si interface can account for the two different growth orientations of epitaxial Ni disilicides on the Si(111) surface after thermal annealing. Annealing the Au/Si interface at high temperature depletes all the Au atoms except for one monolayer of Au on the Si(111) surface. These phenomena are attributed to differences in the metal-Si chemical bonding relations associated with specific atomic structures. After oxygen exposures, both the Ni disilicide surface and Au covered Si surfaces (with different coverages and surface orderings) show silicon in higher oxidation states, in comparison to oxidized silicon on a clean surface

Study on the shrinkage behavior and conductivity of silver microwires during electrostatic field assisted sintering

Science.gov (United States)

Shangguan, Lei; Ma, Liuhong; Li, Mengke; Peng, Wei; Zhong, Yinghui; Su, Yufeng; Duan, Zhiyong

2018-05-01

An electrostatic field was applied to sintering Ag microwires to achieve a more compact structure and better conductivity. The shrinkage behavior of Ag microwires shows anisotropy, since bigger particle sizes, less micropores and smoother surfaces were observed in the direction of the electrostatic field in comparsion with the direction perpendicular to the electrostatic field, and the shrinkage rate of Ag microwires in the direction of electrostatic field improves about 2.4% with the electrostatic field intensity of 800 V cm‑1. The electrostatic field assisted sintering model of Ag microwires is proposed according to thermal diffuse dynamics analysis and experimental research. Moreover, the grain size of Ag microwres sintered with electrostatic field increases with the electrostatic field intensity and reaches 113 nm when the electrostatic field intensity is 800 V cm‑1, and the resistivity decreases to 2.07  ×  10‑8 Ω m as well. This method may overcome the restriction of metal wires which fabricated by the pseudoplastic metal nanoparticle fluid and be used as interconnects in nanoimprint lithography.

Microspot two-photon photoemission spectroscopy for CuPc film on HOPG

International Nuclear Information System (INIS)

Yamada, T.; Yamamoto, R.; Munakata, T.

2015-01-01

Highlights: • Unoccupied levels of CuPc/HOPG are assigned by using 2PPE microspectroscopy. • Lateral distribution of unoccupied energy levels is imaged. • Modified IPS stabilized by the hole localized in the 2nd layer molecule is identified. - Abstract: Microspot two-photon photoemission (micro-2PPE) spectroscopy has been applied to measure the lateral distribution of unoccupied levels on copper phthalocyanine (CuPc) film on HOPG. In addition to the LUMO-derived level and the image potential state (IPS) on the film, we identified the modified IPS which is stabilized by the hole localized in a molecule. We show that modified IPS is observed only on bilayer area, reflecting the localization of the hole in a molecule. The modified IPS is absent on monolayer area, because the hole strongly interacts with substrate.

Photoemission study of 5f localization in UPd/sub 3-x/(Pt,Rh)/sub x/

International Nuclear Information System (INIS)

Arko, A.J.; Koelling, D.D.; Dunlap, B.D.; Mitchell, A.W.

1987-10-01

Photoemission measurements in the two systems UPd/sub 3-x/(Pt,Rh)/sub x/ show that the 5f spectra are consistent with localized 5f electrons (peak in spectral weight is below E/sub F/ for all x within the double hexagonal DO 24 phase) while at both phase transitions the 5f peaks lock in at E/sub F/ consistent with intinerancy. A satellite 5f peak representative of d-screening is observed in both localized and itinerant systems. 17 refs., 3 figs

X-ray imaging and spectroscopy of individual cobalt nanoparticles using photoemission electron microscopy

International Nuclear Information System (INIS)

Fraile Rodriguez, A.; Nolting, F.; Bansmann, J.; Kleibert, A.; Heyderman, L.J.

2007-01-01

Photoemission electron microscopy (PEEM) was employed for X-ray imaging and absorption spectroscopy of individual cobalt nanoparticles as small as 8 nm grown using an arc ion cluster source. Using lithographic markers on the samples we were able to identify the same particles with PEEM and scanning electron microscopy. Significant variations in the shape of the X-ray absorption spectra between different cobalt particles were detected. Furthermore, our data suggest that distinctive spectral information about the individual particles, such as the quenching of oxide-related features and changes in the cobalt L 3 -edge intensity, cancel out and cannot be detected in the measurement over an ensemble of particles

Measurements of Schottky barrier at the low-k SiOC:H/Cu interface using vacuum ultraviolet photoemission spectroscopy

Energy Technology Data Exchange (ETDEWEB)

Guo, X.; Pei, D.; Zheng, H.; Shohet, J. L. [Plasma Processing and Technology Laboratory and Department of Electrical and Computer Engineering, University of Wisconsin-Madison, Madison, Wisconsin 53706 (United States); King, S. W. [Logic Technology Development, Intel Corporation, Hillsboro, Oregon 97124 (United States); Lin, Y.-H.; Fung, H.-S.; Chen, C.-C. [National Synchrotron Radiation Research Center, Hsinchu 30076, Taiwan (China); Nishi, Y. [Department of Electrical Engineering, Stanford University, Stanford, California 94305 (United States)

2015-12-07

The band alignment between copper interconnects and their low-k interlayer dielectrics is critical to understanding the fundamental mechanisms involved in electrical leakage in low-k/Cu interconnects. In this work, vacuum-ultraviolet (VUV) photoemission spectroscopy is utilized to determine the potential of the Schottky barrier present at low-k a-SiOC:H/Cu interfaces. By examining the photoemission spectra before and after VUV exposure of a low-k a-SiOC:H (k = 3.3) thin film fabricated by plasma-enhanced chemical-vapor deposition on a polished Cu substrate, it was found that photons with energies of 4.9 eV or greater can deplete accumulated charge in a-SiOC:H films, while VUV photons with energies of 4.7 eV or less, did not have this effect. These critical values were identified to relate the electric potential of the interface barrier between the a-SiOC:H and the Cu layers. Using this method, the Schottky barrier at the low-k a-SiOC:H (k = 3.3)/Cu interface was determined to be 4.8 ± 0.1 eV.

Optical shaping of a nano-scale tip by femtosecond laser assisted field evaporation

Science.gov (United States)

Di Russo, E.; Houard, J.; Langolff, V.; Moldovan, S.; Rigutti, L.; Deconihout, B.; Blavette, D.; Bogdanowicz, J.; Vella, A.

2018-04-01

We have investigated the morphology of a nanotip under femtosecond laser pulse illumination and a high electric field. We show that both the symmetry and the local radius of the tip change with the direction of laser polarization as against the tip axis. The experiments were performed on the very same GaN nanotip by laser-assisted atom probe tomography and electron tomography. This allowed an accurate assessment of the tip features by following the order of evaporation of single atoms from the surface. A change of atom emission sites was observed when a change of the angle between the tip axis and the linearly polarized electric field of the laser was imposed. This enables an optical control of field-evaporation sites. A close optical control of the tip morphology on a scale below 10 nm is thus achievable. Calculations of the field at nanotip apex and absorption maps support the experimental observations. Based on the present study, methods can be developed for reshaping nanotips at the nanometer level. This finding opens perspectives for numerous applications, making use of nanotips as probes or field emitters, and for plasmonic devices.

Charge-density-wave partial gap opening in quasi-2D KMo{sub 6}O{sub 17} purple bronze studied by angle resolved photoemission spectroscopy

Energy Technology Data Exchange (ETDEWEB)

Valbuena, M.A. [LURE, Centre Universitaire Paris-Sud, Bat. 209D, B.P. 34, 91898 Orsay Cedex (France); Avila, J. [Instituto de Ciencia de Materiales de Madrid, ICMM - CSIC, 28049 Madrid (Spain); Synchrotron SOLEIL, L' Orme des Merisiers, Saint-Aubin - B.P. 48, 91192 GIF-SUR-YVETTE Cedex (France); Pantin, V. [LURE, Centre Universitaire Paris-Sud, Bat. 209D, B.P. 34, 91898 Orsay Cedex (France); Drouard, S. [LEPES-CENES, B.P. 166x, 38042 Grenoble, Cedex 9 (France); Guyot, H. [LEPES-CENES, B.P. 166x, 38042 Grenoble, Cedex 9 (France); Asensio, M.C. [Instituto de Ciencia de Materiales de Madrid, ICMM - CSIC, 28049 Madrid (Spain) and Synchrotron SOLEIL, L' Orme des Merisiers, Saint-Aubin - B.P. 48, 91192 GIF-SUR-YVETTE Cedex (France)]. E-mail: asensio@synchrotron-soleil.fr

2006-05-30

Low dimensional (LD) metallic oxides have been a subject of continuous interest in the last two decades, mainly due to the electronic instabilities that they present at low temperatures. In particular, charge density waves (CDW) instabilities associated with a strong electron-phonon interaction have been found in Molybdenum metallic oxides such as KMo{sub 6}O{sub 17} purple bronze. We report an angle resolved photoemission (ARPES) study from room temperature (RT) to T {approx}40 K well below the Peierls transition temperature for this material, with CDW transition temperature T {sub CDW} {approx}120 K. We have focused on photoemission spectra along {gamma}M high symmetry direction as well as photoemission measurements were taken as a function of temperature at one representative k {sub F} point in the Brillouin zone in order to look for the characteristic gap opening after the phase transition. We found out a pseudogap opening and a decrease in the density of states near the Fermi energy, E {sub F}, consistent with the partial removal of the nested portions of the Fermi surface (FS) at temperature below the CDW transition. In order to elucidate possible Fermi liquid (FL) or non-Fermi liquid (NFL) behaviour we have compared the ARPES data with that one reported on quasi-1D K{sub 0.3}MoO{sub 3} blue bronze.

Time- and angle-resolved photoemission spectroscopy with optimized high-harmonic pulses using frequency-doubled Ti:Sapphire lasers

International Nuclear Information System (INIS)

Eich, S.; Stange, A.; Carr, A.V.; Urbancic, J.; Popmintchev, T.; Wiesenmayer, M.; Jansen, K.; Ruffing, A.; Jakobs, S.; Rohwer, T.; Hellmann, S.; Chen, C.; Matyba, P.; Kipp, L.; Rossnagel, K.; Bauer, M.; Murnane, M.M.; Kapteyn, H.C.; Mathias, S.; Aeschlimann, M.

2014-01-01

Highlights: • We present a scheme to generate high intensity XUV pulses from HHG with variable time-bandwidth product. • Shorter-wavelength driven high-harmonic XUV trARPES provides higher photon flux and increased energy resolution. • High-quality high-harmonic XUV trARPES data with sub 150 meV energy and sub 30 fs time resolution is presented. - Abstract: Time- and angle-resolved photoemission spectroscopy (trARPES) using femtosecond extreme ultraviolet high harmonics has recently emerged as a powerful tool for investigating ultrafast quasiparticle dynamics in correlated-electron materials. However, the full potential of this approach has not yet been achieved because, to date, high harmonics generated by 800 nm wavelength Ti:Sapphire lasers required a trade-off between photon flux, energy and time resolution. Photoemission spectroscopy requires a quasi-monochromatic output, but dispersive optical elements that select a single harmonic can significantly reduce the photon flux and time resolution. Here we show that 400 nm driven high harmonic extreme-ultraviolet trARPES is superior to using 800 nm laser drivers since it eliminates the need for any spectral selection, thereby increasing photon flux and energy resolution to <150 meV while preserving excellent time resolution of about 30 fs

X-ray photoemission analysis of chemically modified TlBr surfaces for improved radiation detectors

International Nuclear Information System (INIS)

Nelson, A. J.; Voss, L. F.; Beck, P. R.; Graff, R. T.; Conway, A. M.; Nikolic, R. J.; Payne, S. A.; Lee, J.-S.; Kim, H.; Cirignano, L.; Shah, K.

2013-01-01

We subjected device-grade TlBr to various chemical treatments used in room temperature radiation detector fabrication to determine the resulting surface composition and electronic structure. As-polished TlBr was treated separately with HCl, SOCl 2 , Br:MeOH and HF solutions. High-resolution photoemission measurements on the valence band electronic structure and Tl 4f, Br 3d, Cl 2p and S 2p core lines were used to evaluate surface chemistry and shallow heterojunction formation. Surface chemistry and valence band electronic structure were correlated with the goal of optimizing the long-term stability and radiation response

Temperature-induced band shift in bulk γ-InSe by angle-resolved photoemission spectroscopy

Science.gov (United States)

Xu, Huanfeng; Wang, Wei; Zhao, Yafei; Zhang, Xiaoqian; Feng, Yue; Tu, Jian; Gu, Chenyi; Sun, Yizhe; Liu, Chang; Nie, Yuefeng; Edmond Turcu, Ion C.; Xu, Yongbing; He, Liang

2018-05-01

Indium selenide (InSe) has recently become popular research topics because of its unique layered crystal structure, direct band gap and high electron mobilities. In this work, we have acquired the electronic structure of bulk γ-InSe at various temperatures using angle-resolved photoemission spectroscopy (ARPES). We have also found that as the temperature decreases, the valence bands of γ-InSe exhibit a monotonic shift to lower binding energies. This band shift is attributed to the change of lattice parameters and has been validated by variable temperature X-ray diffraction measurements and theoretical calculations.

Simple surface structure determination from Fourier transforms of angle-resolved photoemission extended fine structure

Energy Technology Data Exchange (ETDEWEB)

Zheng, Y. [Pennsylvania State Univ., University Park, PA (United States)]|[Lawrence Berkeley Lab., CA (United States); Shirley, D.A. [Pennsylvania State Univ., University Park, PA (United States)

1995-02-01

The authors show by Fourier analyses of experimental data, with no further treatment, that the positions of all the strong peaks in Fourier transforms of angle-resolved photoemission extended fine structure (ARPEFS) from adsorbed surfaces can be explicitly predicted from a trial structure with an accuracy of about {+-} 0.3 {angstrom} based on a single-scattering cluster model together with the concept of a strong backscattering cone, and without any additional analysis. This characteristic of ARPEFS Fourier transforms can be developed as a simple method for determining the structures of adsorbed surfaces to an accuracy of about {+-} 0.1 {angstrom}.

Reduction of thermal expansion in Z-pinches by electron beam assisted magnetic field generation

International Nuclear Information System (INIS)

Heikkinen, J.A.; Karttunen, S.J.

1989-01-01

Weak radial expansion of a Z-pinch plasma column during its strong initial ohmic heating phase is expected when the generation of a confining magnetic field is assisted by a correctly formed electron beam pulse. Appropriate one-dimensional magnetohydrodynamic equations are numerically solved, and the observed increase of plasma radius as a function of time for various discharge parameters is compared to a normal Z-pinch discharge initiation. (author)

Studies on effect of europium concentration on the photoemission of laser ablated Y2O3:Eu based nano-phosphors

International Nuclear Information System (INIS)

Nissamudeen, K.M.; Krishnan, Renju R.; Rajan, Geo; Gopchandran, K.G.

2007-01-01

Full text: Phosphors are essential materials in display applications. Oxide-based phosphors are likely to emerge as the potential choice for the FED red phosphor. Among those oxide-based phosphors, there has been significant research interest in the development of Y 2 O 3 :Eu thin films as one of the most promising oxide based red phosphor systems. Yttrium oxide mixed with europium exhibit strong UV and cathode-ray-excited luminescence that are useful in lamp and display applications. Dielectric Y 2 O 3 film has recently attracted much attention for its potential application as an electric insulation layer in electroluminescent devices and high-density dynamic random access memory gate dielectrics because of its high band gap (5.8 eV) and large dielectric constant (14 to 18). Another important application of Y 2 O 3 has been in luminescent displays as a host material for rare-earth ions, specifically europium, in order to get emission of red light. In the present study thin films were deposited under a vacuum of 10 -6 mbar on fused amorphous quartz substrates using a Q-switched Nd: YAG laser, 532 nm, pulse width 9 n sec, and repetition frequency of 10 Hz, with sintered Y 2 O 3 pellets having different europium concentration as target material. Attempts were made to understand the effect of europium concentration and annealing process on the photoemission properties of the films. A europium concentration of 8 wt% and an annealing temperature of 1173 K were found to be optimum conditions for maximum photoemission. The dependence of structure and morphology of the films on the photoemission intensity are described with XRD patterns and images obtained from AFM and SEM studies

Plasma-assisted ohmic contact for AlGaN/GaN heterostructure field-effect transistors

International Nuclear Information System (INIS)

Zhang, Jiaqi; Wang, Lei; Wang, Qingpeng; Jiang, Ying; Li, Liuan; Ao, Jin-Ping; Zhu, Huichao

2016-01-01

An Al-based ohmic process assisted by an inductively coupled plasma (ICP) recess treatment is proposed for AlGaN/GaN heterostructure field-effect transistors (HFETs) to realize ohmic contact, which is only needed to anneal at 500 °C. The recess treatment was done with SiCl 4 plasma with 100 W ICP power for 20 s and annealing at 575 °C for 1 min. Under these conditions, contact resistance of 0.52 Ωmm was confirmed. To suppress the ball-up phenomenon and improve the surface morphology, an Al/TiN structure was also fabricated with the same conditions. The contact resistance was further improved to 0.30 Ωmm. By using this plasma-assisted ohmic process, a gate-first HFET was fabricated. The device showed high drain current density and high transconductance. The leakage current of the TiN-gate device decreased to 10 −9 A, which was 5 orders of magnitude lower than that of the device annealed at 800 °C. The results showed that the low-temperature ohmic contact process assisted by ICP treatment is promising for the fabrication of gate-first and self-aligned gate HFETs. (paper)

Fermi Surface Manipulation by External Magnetic Field Demonstrated for a Prototypical Ferromagnet

Directory of Open Access Journals (Sweden)

E. Młyńczak

2016-12-01

Full Text Available We consider the details of the near-surface electronic band structure of a prototypical ferromagnet, Fe(001. Using high-resolution angle-resolved photoemission spectroscopy, we demonstrate openings of the spin-orbit-induced electronic band gaps near the Fermi level. The band gaps, and thus the Fermi surface, can be manipulated by changing the remanent magnetization direction. The effect is of the order of ΔE=100  meV and Δk=0.1  Å^{−1}. We show that the observed dispersions are dominated by the bulk band structure. First-principles calculations and one-step photoemission calculations suggest that the effect is related to changes in the electronic ground state and not caused by the photoemission process itself. The symmetry of the effect indicates that the observed electronic bulk states are influenced by the presence of the surface, which might be understood as related to a Rashba-type effect. By pinpointing the regions in the electronic band structure where the switchable band gaps occur, we demonstrate the significance of spin-orbit interaction even for elements as light as 3d ferromagnets. These results set a new paradigm for the investigations of spin-orbit effects in the spintronic materials. The same methodology could be used in the bottom-up design of the devices based on the switching of spin-orbit gaps such as electric-field control of magnetic anisotropy or tunneling anisotropic magnetoresistance.

Development of a high-resolution soft x-ray (30--1500 eV) beamline at the Advanced Light Source and its use for the study of angle-resolved photoemission extended fine structure

International Nuclear Information System (INIS)

Huff, W.R.A.

1996-02-01

ALS Bending magnet beamline 9.3.2 is for high resolution spectroscopy, with circularly polarized light. Fixed included-angle SGM uses three gratings for 30--1500 eV photons; circular polarization is produced by an aperture for selecting the beam above or below the horizontal plane. Photocurrent from upper and lower jaws of entrance slit sets a piezoelectric drive feedback loop on the vertically deflecting mirror for stable beam. End station has a movable platform. With photomeission data from Stanford, structure of c(2x2)P/Fe(100) was determined using angle-resolved photoemission extended fine structure (ARPEFS). Multiple-scattering spherical-wave (MSSW) calculations indicate that P atoms adsorb in fourfold hollow sites 1.02A above the first Fe layer. Self-consistent-field Xα scattered wave calculation confirm that the Fe 1 -Fe 2 space is contracted for S/Fe but not for P/Fe; comparison is made to atomic N and O on Fe(100). Final-state effects on ARPEFS curves used literature data from the S 1s and 2p core levels of c(2x2)S/Ni(001); a generalized Ramsauer-Townsend splitting is present in the 1s but not 2p data. An approximate method for analyzing ARPEFS data from a non-s initial state using only the higher-ell partial wave was tested successfully. ARPEFS data from clean surfaces were collected normal to Ni(111) (3p core levels) and 5 degree off-normal from Cu(111)(3s, 3p). Fourier transforms (FT) resemble adsorbate systems, showing backscattering signals from atoms up to 4 layers below emitters. 3p FTs show scattering from 6 nearest neighbors in the same crystal layer as the emitters. MSSW calulation indicate that Cu 3p photoemission is mostly d-wave. FTs also indicate double-scattering and single-scattering from laterally distant atoms; calculations indicate that the signal is dominated by photoemission from the first 2 crystal layers

An Angle Resolved Photoemission Study of a Mott Insulator and Its Evolution to a High Temperature Superconductor

Energy Technology Data Exchange (ETDEWEB)

Ronning, Filip

2002-03-19

One of the most remarkable facts about the high temperature superconductors is their close proximity to an antiferromagnetically ordered Mott insulating phase. This fact suggests that to understand superconductivity in the cuprates we must first understand the insulating regime. Due to material properties the technique of angle resolved photoemission is ideally suited to study the electronic structure in the cuprates. Thus, a natural starting place to unlocking the secrets of high Tc would appears to be with a photoemission investigation of insulating cuprates. This dissertation presents the results of precisely such a study. In particular, we have focused on the compound Ca{sub 2-x}Na{sub x}CuO{sub 2}Cl{sub 2}. With increasing Na content this system goes from an antiferromagnetic Mott insulator with a Neel transition of 256K to a superconductor with an optimal transition temperature of 28K. At half filling we have found an asymmetry in the integrated spectral weight, which can be related to the occupation probability, n(k). This has led us to identify a d-wave-like dispersion in the insulator, which in turn implies that the high energy pseudogap as seen by photoemission is a remnant property of the insulator. These results are robust features of the insulator which we found in many different compounds and experimental conditions. By adding Na we were able to study the evolution of the electronic structure across the insulator to metal transition. We found that the chemical potential shifts as holes are doped into the system. This picture is in sharp contrast to the case of La{sub 2-x}Sr{sub x}CuO{sub 4} where the chemical potential remains fixed and states are created inside the gap. Furthermore, the low energy excitations (ie the Fermi surface) in metallic Ca{sub 1.9}Na{sub 0.1}CuO{sub 2}Cl{sub 2} is most well described as a Fermi arc, although the high binding energy features reveal the presence of shadow bands. Thus, the results in this dissertation provide a

Interband quasiparticle scattering in superconducting LiFeAs reconciles photoemission and tunneling measurements.

Science.gov (United States)

Hess, Christian; Sykora, Steffen; Hänke, Torben; Schlegel, Ronny; Baumann, Danny; Zabolotnyy, Volodymyr B; Harnagea, Luminita; Wurmehl, Sabine; van den Brink, Jeroen; Büchner, Bernd

2013-01-04

Several angle-resolved photoemission spectroscopy (ARPES) studies reveal a poorly nested Fermi surface of LiFeAs, far away from a spin density wave instability, and clear-cut superconducting gap anisotropies. On the other hand a very different, more nested Fermi surface and dissimilar gap anisotropies have been obtained from quasiparticle interference (QPI) data, which were interpreted as arising from intraband scattering within holelike bands. Here we show that this ARPES-QPI paradox is completely resolved by interband scattering between the holelike bands. The resolution follows from an excellent agreement between experimental quasiparticle scattering data and T-matrix QPI calculations (based on experimental band structure data), which allows disentangling interband and intraband scattering processes.

Study of adsorption states for lubricant molecule using hard X-ray photoemission spectroscopy

International Nuclear Information System (INIS)

Ikenaga, E.; Kobata, M.; Kim, J.J.; Wakabayashi, A.; Nishino, Y.; Tamasaku, K.; Sakane, Y.; Ishikawa, T.; Komiya, S.; Kobayashi, K.

2007-01-01

The adsorption states for lubricant molecules have been investigated using hard X-ray (hν = 7.95 keV) photoemission spectroscopy (HX-PES). This method has the advantage for the organic molecules to be able to measure damage few. Being aware of the fact that P atoms exist only in cyclotriphosphazene base, we measured the take-off angle dependence of the P1s spectra. Each spectrum consists from two peaks, that is, substrate NiP peak and cyclotriphosphazene P peak. The cyclotriphosphazene P peak rapidly disappears with increasing take-off angle. We have also measured C1s spectra. Combining these experimental results, we have found that the adsorption state of cyclotriphosphazene end group is undergoing

Magnetic field-assisted synthesis of wire-like Co3O4 nanostructures: Electrochemical and photocatalytic studies

International Nuclear Information System (INIS)

Zhao, Xiubin; Pang, Zhanwen; Wu, Mingzai; Liu, Xiansong; Zhang, Hui; Ma, Yongqing; Sun, Zhaoqi; Zhang, Lide; Chen, Xiaoshuang

2013-01-01

Graphical abstract: Schematic illustration for the magnetic field-assisted growth of wire-like Co 3 O 4 nanostructure. Display Omitted Highlights: ► Co 3 O 4 nanowires are prepared by magnetic field hydrothermal reduction and annealing. ► These Co 3 O 4 nanowires possess enhanced capacitance. ► The Co 3 O 4 nanowires have a good photocatalytic activity for methyl orange. -- Abstract: Wire-like Co 3 O 4 nanostructures were prepared by the combination of magnetic field-assisted hydrothermal reduction of cobalt ions and the subsequent ambient annealing at 500 °C. X-ray diffraction (XRD) and scanning electron microscopy (SEM) were used to characterize the structure and morphological evolution of the products. The results show that the wire-like nanostructures possess diameters about 250 nm and lengths over 10 μm. The possible formation mechanism of the wire-like Co 3 O 4 nanostructures is also proposed based on the SEM results. Galvanostatic methods were used to characterize the electrochemical properties. The measurements indicate that the wire-like Co 3 O 4 nanostructures show larger discharge and charge capacities than that of spherical Co 3 O 4 nanoparticles prepared in the absence of magnetic field. In addition, the photocatalytic activity of the products was investigated by measuring the photodegradation of methyl orange solution under ultraviolet radiation, which shows that both the wire-like and spherical products have a good photocatalytic activity.

Development of high-performance ER gel produced by electric-field assisted molding

International Nuclear Information System (INIS)

Kakinuma, Y; Aoyama, T; Anzai, H

2009-01-01

Electro-rheological gel (ERG) is a novel functional elastomer whose surface frictional and adhesive property varies according to the intensity of applied electric field. This peculiar phenomenon is named as Electro-adhesive effect. A generated shear stress of ERG under applied electric field is approximately 30∼40 times higher than that of ERF because of high adhesive strength. However, the performances of ERG vary widely due to its surface condition, especially density and distribution of ER particles at the surface. In order to stabilize and improve the performance of ERG, the electric- filed assisted molding process is proposed as the producing method of ERG. In this study, first, the principle of electro-adhesive effect is theoretically investigated. Second, a high-performance ERG produced by the proposed process, in which ER particles are aligned densely at the surface, is developed and its performance is evaluated experimentally. As the experimental result, the high-performance ERG shows twice higher shear stress than the conventional ERG.

Theory of the photoelectric effect assisted by an elliptically polarized laser field

International Nuclear Information System (INIS)

Li Shumin; Jentschura, Ulrich D

2009-01-01

The laser-assisted photoelectric effect in atomic hydrogen is investigated for linear, circular and general elliptic polarizations. The perturbative dressed state of the atom in an elliptically polarized nonresonant laser field is derived in the velocity gauge. The continuum state of the ejected electron is described by a Coulomb-Volkov wavefunction. Numerical results show that the ionization cross section by a vacuum ultraviolet photon is enhanced at high laser field intensities and low frequencies. At small and extremely large scattering angles (measured with respect to the wave vector of the incoming vacuum ultraviolet photon), the process for emitting a laser photon is predominant, while at medium angles, the result favours the process without a laser photon exchange. The dependence of the results on the laser polarization and on various geometries is studied, and an interesting pattern is found for the dependence on the frequency of the dressing laser; an intuitive explanation is offered.

Development of high-performance ER gel produced by electric-field assisted molding

Energy Technology Data Exchange (ETDEWEB)

Kakinuma, Y; Aoyama, T [Department of System Design Engineering, Keio University, 3-14-1 Hiyoshi Kouhoku-ku Yokohama (Japan); Anzai, H [Fujikura kasei Co., Ltd. 2-6-15 Shibakouen, Minato-ku, Tokyo (Japan)], E-mail: kakinuma@sd.keio.ac.jp

2009-02-01

Electro-rheological gel (ERG) is a novel functional elastomer whose surface frictional and adhesive property varies according to the intensity of applied electric field. This peculiar phenomenon is named as Electro-adhesive effect. A generated shear stress of ERG under applied electric field is approximately 30{approx}40 times higher than that of ERF because of high adhesive strength. However, the performances of ERG vary widely due to its surface condition, especially density and distribution of ER particles at the surface. In order to stabilize and improve the performance of ERG, the electric- filed assisted molding process is proposed as the producing method of ERG. In this study, first, the principle of electro-adhesive effect is theoretically investigated. Second, a high-performance ERG produced by the proposed process, in which ER particles are aligned densely at the surface, is developed and its performance is evaluated experimentally. As the experimental result, the high-performance ERG shows twice higher shear stress than the conventional ERG.

Angle Integrated Photoemission Study of SmO0.85F0.15FeAs

International Nuclear Information System (INIS)

Hong-Wei, Ou; Jia-Feng, Zhao; Yan, Zhang; Da-Wei, Shen; Bo, Zhou; Le-Xian, Yang; Cheng, He; Fei, Chen; Min, Xu; Yan, Chen; Dong-Lai, Feng; Tao, Wu; Xian-Hui, Chen

2008-01-01

The electronic structure of the new superconductor SmO 1-x F x FeAs (x = 0.15) is studied by angle-integrated photoemission spectroscopy. Our data show a sharp feature very close to the Fermi energy, and a relative flat distribution of the density of states between 0.5eV and 3eV binding energy, which agrees well with the band structure calculations considering an antiferromagnetic ground state. No noticeable gap opening is observed at 12K below the superconducting transition temperature, indicating the existence of large ungapped regions in the Brillouin zone. (condensed matter: electronic structure, electrical, magnetic, and optical properties)

Study of electrons photoemitted from field emission tips. Progress report, July 1, 1979-March 1, 1980

International Nuclear Information System (INIS)

Reifenberger, R.

1980-02-01

Photo-induced field emission is a technique which studies electrons that have been photoemitted from a field emission tip. This new experimental method promises to combine the proven utility of both field emission and photoemission for investigating the electronic states near a metal surface. The primary objective of the research being performed is to investigate photo-induced field emitted electrons using a tuneable cw dye laser. To fully exploit this continuously tuneable photon source, a differential energy analyzer is being constructed to allow energy resolved measurements of the photo-field emitted electrons. This report describes the progress made in implementing experiments on photo-induced field emission from July 1979 to March 1980

Stable five axes cryogenic photoemission manipulator without a differentially pumped rotary feedthrough

International Nuclear Information System (INIS)

Kim, Bum Joon; Kim, Hyeong-Do; Cho, Deok-Yong; Kim, Myongjin; Oh, S.-J.; Kim, Changyoung

2005-01-01

We report on the design and construction of an ultrahigh vacuum compatible cryogenic manipulator for angle resolved photoemission spectroscopy. Unlike designs that have been used so far, our design allows five motions (three translational and two angular) without a differentially pumped rotary feedthrough. The design greatly reduces the sample motion upon rotation, which is crucial in automatic data acquisition over a large area in the momentum space. The constructed manipulator shows smooth motions in vacuum and the lowest temperature it could reach is about 8 K at the sample position. Angular reproducibilities are found to be about 0.02 deg. for both of the angular motions. The wobbling motion from the rotation around the vertical rotation axis is found to be virtually nonexistent (less than 0.1 mm)

Contrast enhancement of microsphere-assisted super-resolution imaging in dark-field microscopy

Science.gov (United States)

Zhou, Yi; Tang, Yan; Deng, Qinyuan; Zhao, Lixin; Hu, Song

2017-08-01

We report a method of boosting the imaging contrast of microsphere-assisted super-resolution visualization by utilizing dark-field illumination (DFI). We conducted experiments on both 10-µm-diameter silica (SiO2) microspheres with refractive index n ∼ 1.46 under no and partial immersion in ethyl alcohol (n ∼ 1.36) and 20-µm-diameter barium titanate glass (BTG, n ∼ 1.9) microspheres with full immersion to show the super-resolution capability. We experimentally demonstrated that the imaging contrast and uniformity were extraordinarily improved in the DFI mode. The intensity profiles in the visualization also numerically confirm the enhanced sharpness for a better imaging quality when applying DFI.

An aberration corrected photoemission electron microscope at the advanced light source

International Nuclear Information System (INIS)

Feng, J.; MacDowell, A.A.; Duarte, R.; Doran, A.; Forest, E.; Kelez, N.; Marcus, M.; Munson, D.; Padmore, H.; Petermann, K.; Raoux, S.; Robin, D.; Scholl, A.; Schlueter, R.; Schmid, P.; Stohr, J.; Wan, W.; Wei, D.H.; Wu, Y.

2003-01-01

Design of a new aberration corrected Photoemission electron microscope PEEM3 at the Advanced Light Source is outlined. PEEM3 will be installed on an elliptically polarized undulator beamline and will be used for the study of complex materials at high spatial and spectral resolution. The critical components of PEEM3 are the electron mirror aberration corrector and aberration-free magnetic beam separator. The models to calculate the optical properties of the electron mirror are discussed. The goal of the PEEM3 project is to achieve the highest possible transmission of the system at resolutions comparable to our present PEEM2 system (50 nm) and to enable significantly higher resolution, albeit at the sacrifice of intensity. We have left open the possibility to add an energy filter at a later date, if it becomes necessary driven by scientific need to improve the resolution further

Direct characterization of the energy level alignments and molecular components in an organic hetero-junction by integrated photoemission spectroscopy and reflection electron energy loss spectroscopy analysis.

Science.gov (United States)

Yun, Dong-Jin; Shin, Weon-Ho; Bulliard, Xavier; Park, Jong Hwan; Kim, Seyun; Chung, Jae Gwan; Kim, Yongsu; Heo, Sung; Kim, Seong Heon

2016-08-26

A novel, direct method for the characterization of the energy level alignments at bulk-heterojunction (BHJ)/electrode interfaces on the basis of electronic spectroscopy measurements is proposed. The home-made in situ photoemission system is used to perform x-ray/ultraviolet photoemission spectroscopy (XPS/UPS), reflection electron energy loss spectroscopy (REELS) and inverse photoemission spectroscopy of organic-semiconductors (OSCs) deposited onto a Au substrate. Through this analysis system, we are able to obtain the electronic structures of a boron subphthalocyanine chloride:fullerene (SubPC:C60) BHJ and those of the separate OSC/electrode structures (SubPC/Au and C60/Au). Morphology and chemical composition analyses confirm that the original SubPC and C60 electronic structures remain unchanged in the electrodes prepared. Using this technique, we ascertain that the position and area of the nearest peak to the Fermi energy (EF = 0 eV) in the UPS (REELS) spectra of SubPC:C60 BHJ provide information on the highest occupied molecular orbital level (optical band gap) and combination ratio of the materials, respectively. Thus, extracting the adjusted spectrum from the corresponding SubPC:C60 BHJ UPS (REELS) spectrum reveals its electronic structure, equivalent to that of the C60 materials. This novel analytical approach allows complete energy-level determination for each combination ratio by separating its electronic structure information from the BHJ spectrum.

Robot-assisted biopsies in a high-field MRI system. First clinical results; Roboterunterstuetzte Punktion in einem Hochfeld-Kernspintomografen. Erste klinische Ergebnisse

Energy Technology Data Exchange (ETDEWEB)

Schell, B.; Eichler, K.; Mack, M.G.; Mueller, C.; Kerl, J.M.; Beeres, M.; Thalhammer, A.; Vogl, T.J.; Zangos, S. [Frankfurt Univ. (Germany). Inst. fuer Diagnostische und Interventionelle Radiologie; Czerny, C. [Frankfurt Univ. (Germany). Inst. fuer Unfall-, Hand- und Wiederherstellungschirurgie

2012-01-15

Purpose: The purpose of this study was to examine the clinical use of MR-guided biopsies in patients with suspicious lesions using a new MR-compatible assistance system in a high-field MR system. Materials and Methods: Six patients with suspicious focal lesions in various anatomic regions underwent percutanous biopsy in a high-field MR system (1.5 T, Magnetom Espree, Siemens) using a new MR-compatible assistance system (Innomotion). The procedures were planned and guided using T1-weighted FLASH and TrueFISP sequences. A servopneumatic drive then moved the guiding arm automatically to the insertion point. An MRI compatible 15G biopsy system (Somatex) was introduced by a physician guided by the needle holder and multiple biopsies were performed using the coaxial technique. The feasibility, duration of the intervention and biopsy findings were analyzed. Results: The proposed new system allows accurate punctures in a high-field MR system. The assistance device did not interfere with the image quality, and guided the needle virtually exactly as planned. Histological examination could be conducted on every patient. The lesion was malignant in four cases, and an infectious etiology was diagnosed for the two remaining lesions. Regarding the differentiation of anatomical and pathological structures and position monitoring of the insertion needle, TrueFISP images are to be given preference. The average intervention time was 41 minutes. Lesions up to 15.4 cm beneath the skin surface were punctured. Conclusion: The proposed MR-guided assistance system can be successfully utilized in a high-field MR system for accurate punctures of even deep lesions in various anatomic regions. (orig.)

High-intensity xenon plasma discharge lamp for bulk-sensitive high-resolution photoemission spectroscopy.

Science.gov (United States)

Souma, S; Sato, T; Takahashi, T; Baltzer, P

2007-12-01

We have developed a highly brilliant xenon (Xe) discharge lamp operated by microwave-induced electron cyclotron resonance (ECR) for ultrahigh-resolution bulk-sensitive photoemission spectroscopy (PES). We observed at least eight strong radiation lines from neutral or singly ionized Xe atoms in the energy region of 8.4-10.7 eV. The photon flux of the strongest Xe I resonance line at 8.437 eV is comparable to that of the He Ialpha line (21.218 eV) from the He-ECR discharge lamp. Stable operation for more than 300 h is achieved by efficient air-cooling of a ceramic tube in the resonance cavity. The high bulk sensitivity and high-energy resolution of PES using the Xe lines are demonstrated for some typical materials.

Effect of phase formation on valence band photoemission and photoresonance study of Ti/Ni multilayers using synchrotron radiation

International Nuclear Information System (INIS)

Bhatt, Pramod; Chaudhari, S.M.

2006-01-01

This paper presents investigation of Ti-Ni alloy phase formation and its effect on valence band (VB) photoemission and photoresonance study of as-deposited as well as annealed Ti/Ni multilayers (MLs) up to 600 deg. C using synchrotron radiation. For this purpose [Ti (50 A)/Ni (50 A)]X 10 ML structures were deposited by using electron-beam evaporation technique under ultra-high vacuum (UHV) conditions. Formation of different phases of Ti-Ni alloy due to annealing treatment has been confirmed by the X-ray diffraction (XRD) technique. The XRD pattern corresponding as-deposited ML sample shows crystalline nature of both Ti and Ni deposited layers, whereas 300 deg. C annealed ML sample show solid-state reaction (SSR) leading to amorphization and subsequent recrystallisation at higher temperatures of annealing (≥400 deg. C) with the formation of TiNi, TiNi 3 and Ti 2 Ni alloy phases. The survey scans corresponding to 400, 500 and 600 deg. C annealed ML sample shows interdiffusion and intermixing of Ni atoms into Ti layers leading to chemical Ti-Ni alloys phase formation at interface. The corresponding recorded VB spectra using synchrotron radiation at 134 eV on as-deposited ML sample with successive sputtering shows alternately photoemission bands due to Ti 3d and Ni 3d, respectively, indicating there is no mixing of the consequent layers and any phase formation at the interface during deposition. However, ML samples annealed at higher temperatures of annealing, particularly at 400, 500 and 600 deg. C show a clear shift in Ni 3d band and its satellite peak position to higher BE side indicates Ti-Ni alloy phase formation. In addition to this, reduction of satellite peak intensity and Ni 3d density of states (DOS) near Fermi level is also observed due to Ti-Ni phase formation with higher annealing temperatures. The variable photon energy VB measurements on as-deposited and ML samples annealed at 400 deg. C confirms existence and BE position of observed Ni 3d satellite

Field-emission from quantum-dot-in-perovskite solids.

Science.gov (United States)

García de Arquer, F Pelayo; Gong, Xiwen; Sabatini, Randy P; Liu, Min; Kim, Gi-Hwan; Sutherland, Brandon R; Voznyy, Oleksandr; Xu, Jixian; Pang, Yuangjie; Hoogland, Sjoerd; Sinton, David; Sargent, Edward

2017-03-24

Quantum dot and well architectures are attractive for infrared optoelectronics, and have led to the realization of compelling light sensors. However, they require well-defined passivated interfaces and rapid charge transport, and this has restricted their efficient implementation to costly vacuum-epitaxially grown semiconductors. Here we report solution-processed, sensitive infrared field-emission photodetectors. Using quantum-dots-in-perovskite, we demonstrate the extraction of photocarriers via field emission, followed by the recirculation of photogenerated carriers. We use in operando ultrafast transient spectroscopy to sense bias-dependent photoemission and recapture in field-emission devices. The resultant photodiodes exploit the superior electronic transport properties of organometal halide perovskites, the quantum-size-tuned absorption of the colloidal quantum dots and their matched interface. These field-emission quantum-dot-in-perovskite photodiodes extend the perovskite response into the short-wavelength infrared and achieve measured specific detectivities that exceed 10 12 Jones. The results pave the way towards novel functional photonic devices with applications in photovoltaics and light emission.

Direct observation of superconducting gaps in MgB 2 by angle-resolved photoemission spectroscopy

Science.gov (United States)

Souma, S.; Machida, Y.; Sato, T.; Takahashi, T.; Matsui, H.; Wang, S.-C.; Ding, H.; Kaminski, A.; Campuzano, J. C.; Sasaki, S.; Kadowaki, K.

2004-08-01

High-resolution angle-resolved photoemission spectroscopy has been carried out to clarify the anomalous superconductivity of MgB 2. We observed three bands crossing the Fermi level, which are ascribed to B2p-σ, π and surface bands. We have succeeded for the first time in directly observing the superconducting gaps of these bands separately. We have found that the superconducting-gap sizes of σ and surface bands are 6.5 ± 0.5 and 6.0 ± 0.5 meV, respectively, while that of the π band is much smaller (1.5 ± 0.5 meV). The present experimental result unambiguously demonstrates the validity of the two-band superconductivity in MgB 2.

Direct observation of superconducting gaps in MgB2 by angle-resolved photoemission spectroscopy

International Nuclear Information System (INIS)

Souma, S.; Machida, Y.; Sato, T.; Takahashi, T.; Matsui, H.; Wang, S.-C.; Ding, H.; Kaminski, A.; Campuzano, J.C.; Sasaki, S.; Kadowaki, K.

2004-01-01

High-resolution angle-resolved photoemission spectroscopy has been carried out to clarify the anomalous superconductivity of MgB 2 . We observed three bands crossing the Fermi level, which are ascribed to B2p-σ, π and surface bands. We have succeeded for the first time in directly observing the superconducting gaps of these bands separately. We have found that the superconducting-gap sizes of σ and surface bands are 6.5 ± 0.5 and 6.0 ± 0.5 meV, respectively, while that of the π band is much smaller (1.5 ± 0.5 meV). The present experimental result unambiguously demonstrates the validity of the two-band superconductivity in MgB 2

Photoemission studies using femtosecond pulses for high brightness electron beams

International Nuclear Information System (INIS)

Srinivasan-Rao, T.; Tsang, T.; Fischer, J.

1990-06-01

We present the results of a series of experiments where various metal photocathodes are irradiated with ultrashort laser pulses, whose characteristics are: λ = 625 nm, τ = 100 fs, PRR = 89.5 MHz, Hν = 2 eV and average power 25 mW in each of the two beams. The quantum efficiency of the metals range from ∼10 -12 to 10 -8 at a power density of 100 MW/cm 2 at normal incidence. Since all the electrons are emitted due to multiphoton processes, these efficiencies are expected to increase substantially at large intensities. The efficiency at 100 MW/cm 2 has been increased by using p-polarized light at oblique incidence by ∼20x and by mediating the electron emission through surface plasmon excitation by ∼10 3 x. For the low intensities used in these experiments, the electron pulse duration is almost the same as the laser pulse duration for both the bulk and the surface plasmon mediated photoemission. 7 refs., 8 figs., 2 tabs

Exploring the magnetic and organic microstructures with photoemission electron microscope

International Nuclear Information System (INIS)

Wei, D.H.; Chan, Yuet-Loy; Hsu, Yao-Jane

2012-01-01

Highlights: ► PEEM with polarized photon enables additional image contrasts and physical insights. ► XMCD-based images reveal the shape-dependent domains in Ni80Fe20 microstructures. ► XLD-based images confirm the success of molecular orientation controls. ► The two interfaces in Co–Pn–Co structures are magnetically and chemically different. -- Abstract: We present photoemission electron microscopy (PEEM) studies on geometrically constrained ferromagnetic, organic, and organics–ferromagnet hybrid structures. Powered by an elliptically polarized undulator, the PEEM at Taiwan Light Source (TLS) is capable of recording polarization enhanced X-ray images and has been employed to examine the domain configurations in a lithographically patterned permalloy film as well as the orientations of pentacene molecules adsorbed on self-assembled monolayers (SAMs) modified gold surfaces. In addition, magnetic images acquired on cobalt/pentacene and pentacene/cobalt bilayers reveal that in hybrid structures the order of thin film deposition can lead to distinct domain configurations. Spectroscopic evidence further suggests that there is significant orbital hybridization at the interface where metallic cobalt was deposited directly on organic pentacene.

VUV photoemission studies of candidate Large Hadron Collider vacuum chamber materials

CERN Document Server

Cimino, R; Baglin, V

1999-01-01

In the context of future accelerators and, in particular, the beam vacuum of the Large Hadron Collider (LHC), a 27 km circumference proton collider to be built at CERN, VUV synchrotron radiation (SR) has been used to study both qualitatively and quantitatively candidate vacuum chamber materials. Emphasis is given to show that angle and energy resolved photoemission is an extremely powerful tool to address important issues relevant to the LHC, such as the emission of electrons that contributes to the creation of an electron cloud which may cause serious beam instabilities and unmanageable heat loads on the cryogenic system. Here we present not only the measured photoelectron yields from the proposed materials, prepared on an industrial scale, but also the energy and in some cases the angular dependence of the emitted electrons when excited with either a white light (WL) spectrum, simulating that in the arcs of the LHC, or monochromatic light in the photon energy range of interest. The effects on the materials ...

Influence of direct and alternating current electric fields on efficiency promotion and leaching risk alleviation of chelator assisted phytoremediation.

Science.gov (United States)

Luo, Jie; Cai, Limei; Qi, Shihua; Wu, Jian; Sophie Gu, Xiaowen

2018-03-01

Direct and alternating current electric fields with various voltages were used to improve the decontamination efficiency of chelator assisted phytoremediation for multi-metal polluted soil. The alleviation effect of electric field on leaching risk caused by chelator application during phytoremediation process was also evaluated. Biomass yield, pollutant uptake and metal leaching retardation under alternating current (AC) and direct current (DC) electric fields were compared. The biomass yield of Eucalyptus globulus under AC fields with various voltages (2, 4 and 10 V) were 3.91, 4.16 and 3.67kg, respectively, significantly higher than the chelator treatment without electric field (2.71kg). Besides growth stimulation, AC fields increased the metal concentrations of plant tissues especially in aerial parts manifested by the raised translocation factor of different metals. Direct current electric fields with low and moderate voltages increased the biomass production of the species to 3.45 and 3.12kg, respectively, while high voltage on the contrary suppressed the growth of the plants (2.66kg). Under DC fields, metal concentrations elevated obviously with increasing voltages and the metal translocation factors were similar under all voltages. Metal extraction per plant achieved the maximum value under moderate voltage due to the greatest biomass production. DC field with high voltage (10V) decreased the volume of leachate from the chelator treatment without electric field from 1224 to 56mL, while the leachate gathered from AC field treatments raised from 512 to 670mL. DC field can retard the downward movement of metals caused by chelator application more effectively relative to AC field due to the constant water flow and electroosmosis direction. Alternating current field had more promotive effect on chelator assisted phytoremediation efficiency than DC field illustrated by more metal accumulation in the species. However, with the consideration of leaching risk, DC

Strain-assisted current-induced magnetization reversal in magnetic tunnel junctions: A micromagnetic study with phase-field microelasticity

International Nuclear Information System (INIS)

Huang, H. B.; Hu, J. M.; Yang, T. N.; Chen, L. Q.; Ma, X. Q.

2014-01-01

Effect of substrate misfit strain on current-induced in-plane magnetization reversal in CoFeB-MgO based magnetic tunnel junctions is investigated by combining micromagnetic simulations with phase-field microelasticity theory. It is found that the critical current density for in-plane magnetization reversal decreases dramatically with an increasing substrate strain, since the effective elastic field can drag the magnetization to one of the four in-plane diagonal directions. A potential strain-assisted multilevel bit spin transfer magnetization switching device using substrate misfit strain is also proposed.

Electronic structure of C r2AlC as observed by angle-resolved photoemission spectroscopy

Science.gov (United States)

Ito, Takahiro; Pinek, Damir; Fujita, Taishi; Nakatake, Masashi; Ideta, Shin-ichiro; Tanaka, Kiyohisa; Ouisse, Thierry

2017-11-01

We investigate the electronic band structure and Fermi surfaces (FSs) of C r2AlC single crystals with angle-resolved photoemission spectroscopy. We evidence hole bands centered around the M points and electron bands centered around the Γ point in reciprocal space. Electron and hole bands exhibit an open, tubular structure along the c axis, confirming the quasi-two-dimensional character of this highly anisotropic, nanolamellar compound. Dependence of the photoionization cross sections on beam light polarization and orientation allows us to assess the orbital character of each observed band locally. Despite some differences, density functional theory calculations show a good agreement with experiment.

Educating the Employee Assistance Professional: Cornell University's Employee Assistance Education and Research Program.

Science.gov (United States)

Quick, R. C.; And Others

1987-01-01

Outlines Cornell University's Employee Assistance Education and Research Program, which uses an academic curriculum and field experience to further develop the Employee Assistance Program (EAP) profession. Addresses the dilemma of personnel executives in ensuring quality in EAP programs and staff. (JOW)

Ga droplet morphology on GaAs(001) studied by Lloyd's mirror photoemission electron microscopy

Energy Technology Data Exchange (ETDEWEB)

Tang, W X; Jesson, D E; Pavlov, K M; Morgan, M J [School of Physics, Monash University, Victoria 3800 (Australia); Usher, B F [Department of Electronic Engineering, La Trobe University, Victoria 3086 (Australia)

2009-08-05

We apply Lloyd's mirror photoemission electron microscopy (PEEM) to study the surface shape of Ga droplets on GaAs(001). An unusual rectangular-based droplet shape is identified and the contact angle is determined in situ. It is shown that quenching does not appreciably affect droplet shape and ex situ measurements of the contact angle by atomic force microscopy are in good agreement with Lloyd's mirror PEEM. Extension of Lloyd's mirror technique to reconstruct general three-dimensional (3D) surface shapes and the potential use of synchrotron radiation to improve vertical resolution is discussed.

Photoemission perspective on pseudogap, superconducting fluctuations, and charge order in cuprates: a review of recent progress

Science.gov (United States)

Vishik, I. M.

2018-06-01

In the course of seeking the microscopic mechanism of superconductivity in cuprate high temperature superconductors, the pseudogap phase— the very abnormal ‘normal’ state on the hole-doped side— has proven to be as big of a quandary as superconductivity itself. Angle-resolved photoemission spectroscopy (ARPES) is a powerful tool for assessing the momentum-dependent phenomenology of the pseudogap, and recent technological developments have permitted a more detailed understanding. This report reviews recent progress in understanding the relationship between superconductivity and the pseudogap, the Fermi arc phenomena, and the relationship between charge order and pseudogap from the perspective of ARPES measurements.

Photoemission study of electronic structure of the half-metallic ferromagnet Co3Sn2S2

Science.gov (United States)

Holder, M.; Dedkov, Yu. S.; Kade, A.; Rosner, H.; Schnelle, W.; Leithe-Jasper, A.; Weihrich, R.; Molodtsov, S. L.

2009-05-01

Surface electronic structure of polycrystalline and single-crystalline samples of the half-metallic ferromagnet Co3Sn2S2 was studied by means of angle-resolved and core-level photoemissions. The experiments were performed in temperature regimes both above and below a Curie temperature of 176.9 K. The spectroscopic results are compared to local-spin density approximation band-structure calculations for the bulk samples. It is found that the surface sensitive experimental data are generally reproduced by the bulk computation suggesting that the theoretically predicted half-metallic properties of Co3Sn2S2 are retained at the surface.

Schottky barrier measurements on individual GaAs nanowires by X-ray photoemission microscopy

Energy Technology Data Exchange (ETDEWEB)

Di Mario, Lorenzo [IMM-CNR, via del Fosso del Cavaliere 100, 00133 Rome (Italy); Turchini, Stefano, E-mail: stefano.turchini@cnr.it [ISM-CNR, via del Fosso del Cavaliere 100, 00133 Rome (Italy); Zamborlini, Giovanni; Feyer, Vitaly [Peter Grünberg Institute (PGI-6) and JARA-FIT, Research Center Jülich, 52425 Jülich (Germany); Tian, Lin [IMM-CNR, via del Fosso del Cavaliere 100, 00133 Rome (Italy); Schneider, Claus M. [Peter Grünberg Institute (PGI-6) and JARA-FIT, Research Center Jülich, 52425 Jülich (Germany); Fakultät für Physik and Center for Nanointegration Duisburg-Essen (CENIDE), Universität Duisburg-Essen, D-47048 Duisburg (Germany); Rubini, Silvia [IOM-CNR, TASC Laboratory, Basovizza 34149, Trieste (Italy); Martelli, Faustino, E-mail: faustino.martelli@cnr.it [IMM-CNR, via del Fosso del Cavaliere 100, 00133 Rome (Italy)

2016-11-15

Highlights: • The Schottky barrier at the interface between Cu and GaAs nanowires was measured. • Individual nanowires were investigated by X-ray Photoemission Microscopy. • The Schottky barrier at different positions along the nanowire was evaluated. - Abstract: We present measurements of the Schottky barrier height on individual GaAs nanowires by means of x-ray photoelectron emission microscopy (XPEEM). Values of 0.73 and 0.51 eV, averaged over the entire wires, were measured on Cu-covered n-doped and p-doped GaAs nanowires, respectively, in agreement with results obtained on bulk material. Our measurements show that XPEEM can become a feasible and reliable investigation tool of interface formation at the nanoscale and pave the way towards the study of size-dependent effects on semiconductor-based structures.

Gas-phase photoemission with soft x-rays: Cross sections and angular distributions

International Nuclear Information System (INIS)

Shirley, D.A.; Kobrin, P.H.; Truesdale, C.M.; Lindle, D.W.; Ferrett, T.A.; Heimann, P.A.; Becker, U.; Kerkhoff, H.G.; Southworth, S.H.

1983-01-01

A summary is presented of typical gas-phase photoemission studies based on synchrotron radiation in the 50-5000 eV range, using beam lines at the Stanford Synchrotron Radiation Laboratory. Three topics are addressed: atomic inner-shell photoelectron cross sections and asymmetries, correlation peaks in rare gases, and core-level shape resonances in molecules. Photoelectron cross-section σ(n iota) and asymmetry-parameter β(n iota) studies in mercury vapor at photon energies up to 270 eV (up to 600 eV for β/sub 4f/) extend coverage of these parameters to n≤5 and iota≤3. Comparison with Dirac-Slater and relativistic random-phase approximation calculations reveals systematic discrepancies. For example, distinct Cooper minima in σ(n iota) are observed but not predicted, while predicted β(n iota) values are typically too high. Correlation satellites have been studied for the K shells of helium (hν = 68-90 eV), neon (hν = 870-960 eV) and argon (hν = 3200-3320 eV). In helium the n=2 satellite peak was shown to have mainly 2p character at threshold, and its asymmetry was measured through the autoionizing resonance region. Tentative evidence was obtained that the neon satellites are less intense near threshold than in the high-energy limit, and that their intensities stay constant or decrease with increasing energy near threshold. A new satellite was observed in argon at 24.6 eV which appears to increase in intensity with energy. Molecular core-level shape resonances were observed for the first time by photoemission, yielding σ(hν) and β(hν) for core levels from 180 eV binding energy (S 2p in SF/sub 6/ and OCS) through C 1s in CO, CO/sub 2/ and CF/sub 4/, N 1s in N/sub 2/ and NO, and O 1s in CO and CO/sub 2/ to 2490 eV (S 1s in SF/sub 6/). Several conclusions can be drawn about the photoelectron and Auger cross sections and asymmetry parameters

Field evaluation of personal digital assistant enabled by global positioning system : impact on quality of activity and diary data

NARCIS (Netherlands)

Bellemans, T.; Kochan, B.; Janssens, D.; Wets, G.; Timmermans, H.J.P.; Stopher, P.

2016-01-01

Tom Bellemans, Bruno Kochan, Davy Janssens, Geert Wets and Harry Timmermans (2008), ‘Field Evaluation of Personal Digital Assistant Enabled by Global Positioning System: Impact on Quality of Activity and Diary Data’, Transportation Research Record: Journal of the Transportation Research Board, No.

Magnetic x-ray linear dichroism in resonant and non-resonant Gd 4f photoemission

Energy Technology Data Exchange (ETDEWEB)

Mishra, S.; Gammon, W.J.; Pappas, D.P. [Virginia Commonwealth Univ., Richmond, VA (United States)] [and others

1997-04-01

The enhancement of the magnetic linear dichroism in resonant 4f photoemission (MLDRPE) is studied from a 50 monolayer film of Gd/Y(0001). The ALS at beamline 7.0.1 provided the source of linearly polarized x-rays used in this study. The polarized light was incident at an angle of 30 degrees relative to the film plane, and the sample magnetization was perpendicular to the photon polarization. The linear dichroism of the 4f core levels is measured as the photon energy is tuned through the 4d-4f resonance. The authors find that the MLDRPE asymmetry is strongest at the resonance. Near the threshold the asymmetry has several features which are out of phase with the fine structure of the total yield.

Magnetic x-ray linear dichroism in resonant and non-resonant Gd 4f photoemission

International Nuclear Information System (INIS)

Mishra, S.; Gammon, W.J.; Pappas, D.P.

1997-01-01

The enhancement of the magnetic linear dichroism in resonant 4f photoemission (MLDRPE) is studied from a 50 monolayer film of Gd/Y(0001). The ALS at beamline 7.0.1 provided the source of linearly polarized x-rays used in this study. The polarized light was incident at an angle of 30 degrees relative to the film plane, and the sample magnetization was perpendicular to the photon polarization. The linear dichroism of the 4f core levels is measured as the photon energy is tuned through the 4d-4f resonance. The authors find that the MLDRPE asymmetry is strongest at the resonance. Near the threshold the asymmetry has several features which are out of phase with the fine structure of the total yield

A Polarization-Adjustable Picosecond Deep-Ultraviolet Laser for Spin- and Angle-Resolved Photoemission Spectroscopy

International Nuclear Information System (INIS)

Zhang Feng-Feng; Yang Feng; Zhang Shen-Jin; Wang Zhi-Min; Xu Feng-Liang; Peng Qin-Jun; Zhang Jing-Yuan; Xu Zu-Yan; Wang Xiao-Yang; Chen Chuang-Tian

2012-01-01

We report on a polarization-adjustable picosecond deep-ultraviolet (DUV) laser at 177.3 nm. The DUV laser was produced by second harmonic generation from a mode-locked laser at 355 nm in nonlinear optical crystal KBBF. The laser delivered a maximum average output power of 1.1 mW at 177.3 nm. The polarization of the 177.3 nm beam was adjusted with linear and circular polarization by means of λ/4 and λ/2 wave plates. To the best of our knowledge, the laser has been employed as the circularly polarized and linearly polarized DUV light source for a spin- and angle-resolved photoemission spectroscopy with high resolution for the first time. (fundamental areas of phenomenology(including applications))

Reactive molecular beam epitaxial growth and in situ photoemission spectroscopy study of iridate superlattices

Directory of Open Access Journals (Sweden)

C. C. Fan

2017-08-01

Full Text Available High-quality (001-oriented perovskite [(SrIrO3m/(SrTiO3] superlattices (m=1/2, 1, 2, 3 and ∞ films have been grown on SrTiO3(001 epitaxially using reactive molecular beam epitaxy. Compared to previously reported superlattices synthesized by pulsed laser deposition, our superlattices exhibit superior crystalline, interface and surface structure, which have been confirmed by high-resolution X-ray diffraction, scanning transmission electron microscopy and atomic force microscopy, respectively. The transport measurements confirm a novel insulator-metal transition with the change of dimensionality in these superlattices, and our first systematic in situ photoemission spectroscopy study indicates that the increasing strength of effective correlations induced by reducing dimensionality would be the dominating origin of this transition.

Photoemission study of Kr 3d→np autoionization resonances

International Nuclear Information System (INIS)

Lindle, D.W.; Heimann, P.A.; Ferrett, T.A.; Piancastelli, M.N.; Shirley, D.A.

1987-01-01

Resonant photoelectron spectra of Kr have been taken in the photon-energy ranges of the 3d/sub 5/2/→5p,6p and 3d/sub 3/2/→5p excitations. The spectra, which closely resemble normal Kr + 3d/sup -1/ Auger spectra, illustrate the importance of ''spectator'' Auger-like decay for inner-shell resonances, in which the initially excited electron does not participate in the core-hole deexcitation process, except to respond to the change in the atomic potential. Possible assignments for some of the spectator decay channels are discussed based on photoemission intensity measurements at the different 3d resonances. These assignments suggest that shake-up (e.g., 5p→6p) of the ''spectator'' electron during the decay process is not quite as important as previously suspected. The resonance profiles of some of the more intense satellites have been determined over the 3d→np resonances. Very small resonance effects also were observed in the partial cross section for 4p subshell ionization, which produced asymmetric Fano-type profiles. The 4p angular distribution, in contrast, exhibits a pronounced effect in the resonance energy range. The 4p results demonstrate that nonspectator autoionization also is present

Study on Gap Flow Field Simulation in Small Hole Machining of Ultrasonic Assisted EDM

Science.gov (United States)

Liu, Yu; Chang, Hao; Zhang, Wenchao; Ma, Fujian; Sha, Zhihua; Zhang, Shengfang

2017-12-01

When machining a small hole with high aspect ratio in EDM, it is hard for the flushing liquid entering the bottom gap and the debris could hardly be removed, which results in the accumulation of debris and affects the machining efficiency and machining accuracy. The assisted ultrasonic vibration can improve the removal of debris in the gap. Based on dynamics simulation software Fluent, a 3D model of debris movement in the gap flow field of EDM small hole machining assisted with side flushing and ultrasonic vibration is established in this paper. When depth to ratio is 3, the laws of different amplitudes and frequencies on debris distribution and removal are quantitatively analysed. The research results show that periodic ultrasonic vibration can promote the movement of debris, which is beneficial to the removal of debris in the machining gap. Compared to traditional small hole machining in EDM, the debris in the machining gap is greatly reduced, which ensures the stability of machining process and improves the machining efficiency.

Direct observation of superconducting gaps in MgB{sub 2} by angle-resolved photoemission spectroscopy

Energy Technology Data Exchange (ETDEWEB)

Souma, S.; Machida, Y.; Sato, T.; Takahashi, T.; Matsui, H.; Wang, S.-C.; Ding, H.; Kaminski, A.; Campuzano, J.C.; Sasaki, S.; Kadowaki, K

2004-08-01

High-resolution angle-resolved photoemission spectroscopy has been carried out to clarify the anomalous superconductivity of MgB{sub 2}. We observed three bands crossing the Fermi level, which are ascribed to B2p-{sigma}, {pi} and surface bands. We have succeeded for the first time in directly observing the superconducting gaps of these bands separately. We have found that the superconducting-gap sizes of {sigma} and surface bands are 6.5 {+-} 0.5 and 6.0 {+-} 0.5 meV, respectively, while that of the {pi} band is much smaller (1.5 {+-} 0.5 meV). The present experimental result unambiguously demonstrates the validity of the two-band superconductivity in MgB{sub 2}.

Exploring the magnetic and organic microstructures with photoemission electron microscope

Energy Technology Data Exchange (ETDEWEB)

Wei, D.H., E-mail: dhw@nsrrc.org.tw [National Synchrotron Radiation Research Center, Hsinchu Science Park, 30076 Hsinchu, Taiwan (China); Chan, Yuet-Loy; Hsu, Yao-Jane [National Synchrotron Radiation Research Center, Hsinchu Science Park, 30076 Hsinchu, Taiwan (China)

2012-10-15

Highlights: Black-Right-Pointing-Pointer PEEM with polarized photon enables additional image contrasts and physical insights. Black-Right-Pointing-Pointer XMCD-based images reveal the shape-dependent domains in Ni80Fe20 microstructures. Black-Right-Pointing-Pointer XLD-based images confirm the success of molecular orientation controls. Black-Right-Pointing-Pointer The two interfaces in Co-Pn-Co structures are magnetically and chemically different. -- Abstract: We present photoemission electron microscopy (PEEM) studies on geometrically constrained ferromagnetic, organic, and organics-ferromagnet hybrid structures. Powered by an elliptically polarized undulator, the PEEM at Taiwan Light Source (TLS) is capable of recording polarization enhanced X-ray images and has been employed to examine the domain configurations in a lithographically patterned permalloy film as well as the orientations of pentacene molecules adsorbed on self-assembled monolayers (SAMs) modified gold surfaces. In addition, magnetic images acquired on cobalt/pentacene and pentacene/cobalt bilayers reveal that in hybrid structures the order of thin film deposition can lead to distinct domain configurations. Spectroscopic evidence further suggests that there is significant orbital hybridization at the interface where metallic cobalt was deposited directly on organic pentacene.

Theory of temperature dependent photoemission spectrum of heavy fermion semiconductors

International Nuclear Information System (INIS)

Riseborough, P.S.

1998-01-01

The heavy fermion semiconductors are a class of strongly correlated materials, that at high temperatures show properties similar to those of heavy fermion materials, but at low temperatures show a cross-over into a semi-conducting state. The low temperature insulating state is characterized by an anomalously small energy gap, varying between 10 and 100 K. The smallness of the gap is attributed to the result of a many-body renormalization, and is temperature dependent. The temperature dependence of the electronic spectral density of states is calculated, using the Anderson lattice model at half filling. The spectrum is calculated to second order in 1/N, where N is the degeneracy of the 'f' orbitals, using a slave boson technique. The system is an indirect gap semi-conductor, with an extremely temperature dependent electronic spectral density A(k, ω). The indirect gap is subject to a temperature dependent many-body renormalization, and leads to a sharp temperature dependent structure in the angle resolved photo-emission spectrum at the indirect threshold. The theoretical predictions are compared with experimental observations on FeSi. (Copyright (1998) World Scientific Publishing Co. Pte. Ltd)

Comparison of the Effectiveness of Water-Based Extraction of Substances from Dry Tea Leaves with the Use of Magnetic Field Assisted Extraction Techniques

Directory of Open Access Journals (Sweden)

Grzegorz Zaguła

2017-10-01

Full Text Available This article presents the findings of a study investigating the feasibility of using a magnetic field assisted technique for the water-based extraction of mineral components, polyphenols, and caffeine from dry black and green tea leaves. The authors present a concept of applying constant and variable magnetic fields in the process of producing water-based infusions from selected types of tea. Analyses investigating the effectiveness of the proposed technique in comparison with conventional infusion methods assessed the contents of selected mineral components—i.e., Al, Ca, Cu, K, Mg, P, S, and Zn—which were examined with the use of ICP-OES. The contents of caffeine and polyphenolic compounds were assessed using the HPLC. A changing magnetic field permitted an increased effectiveness of extraction of the mineral components, caffeine, and polyphenols. The findings support the conclusion that a changing magnetic field assisted extraction method is useful for obtaining biologically valuable components from tea infusions.

Deflection gating for time-resolved x-ray magnetic circular dichroism-photoemission electron microscopy using synchrotron radiation

Science.gov (United States)

Wiemann, C.; Kaiser, A. M.; Cramm, S.; Schneider, C. M.

2012-06-01

In this paper, we present a newly developed gating technique for a time-resolving photoemission microscope. The technique makes use of an electrostatic deflector within the microscope's electron optical system for fast switching between two electron-optical paths, one of which is used for imaging, while the other is blocked by an aperture stop. The system can be operated with a switching time of 20 ns and shows superior dark current rejection. We report on the application of this new gating technique to exploit the time structure in the injection bunch pattern of the synchrotron radiation source BESSY II at Helmholtz-Zentrum Berlin for time-resolved measurements in the picosecond regime.

Photoemission study of the temperature-dependent energy-gap formation in the Kondo semiconductor CeRhAs

International Nuclear Information System (INIS)

Shimada, K.; Arita, M.; Takeda, Y.; Namatame, H.; Taniguchi, M.; Higashiguchi, M.; Oguchi, T.; Sasakawa, T.; Suemitsu, T.; Takabatake, T.

2004-01-01

Full text: The orthorhombic CeRhAs, known as a Kondo semiconductor, has attracted much interest for its unusual energy-gap formation associated with the successive 1st order phase transitions. In order to elucidate the mechanism of the energy- gap formation, we have done high-resolution temperature-dependent photoemission spectroscopy on the undulator beamlines of a compact electron-storage ring, HiSOR, at Hiroshima University. We have observed directly the energy-gap formation in the Ce 4f states and in the conduction bands. Comparing with the isostructural Kondo semimetal CeRhSb, we discuss the energy gap formation in CeRhAs

Vacuum space charge effects in sub-picosecond soft X-ray photoemission on a molecular adsorbate layer.

Science.gov (United States)

Dell'Angela, M; Anniyev, T; Beye, M; Coffee, R; Föhlisch, A; Gladh, J; Kaya, S; Katayama, T; Krupin, O; Nilsson, A; Nordlund, D; Schlotter, W F; Sellberg, J A; Sorgenfrei, F; Turner, J J; Öström, H; Ogasawara, H; Wolf, M; Wurth, W

2015-03-01

Vacuum space charge induced kinetic energy shifts of O 1s and Ru 3d core levels in femtosecond soft X-ray photoemission spectra (PES) have been studied at a free electron laser (FEL) for an oxygen layer on Ru(0001). We fully reproduced the measurements by simulating the in-vacuum expansion of the photoelectrons and demonstrate the space charge contribution of the high-order harmonics in the FEL beam. Employing the same analysis for 400 nm pump-X-ray probe PES, we can disentangle the delay dependent Ru 3d energy shifts into effects induced by space charge and by lattice heating from the femtosecond pump pulse.

Electric field-assisted formation of organically modified hydroxyapatite (ormoHAP) spheres in carboxymethylated gelatin gels.

Science.gov (United States)

Heinemann, C; Heinemann, S; Kruppke, B; Worch, H; Thomas, J; Wiesmann, H P; Hanke, T

2016-10-15

A biomimetic strategy was developed in order to prepare organically modified hydroxyapatite (ormoHAP) with spherical shape. The technical approach is based on electric field-assisted migration of calcium ions and phosphate ions into a hydrogel composed of carboxymethylated gelatin. The electric field as well as the carboxymethylation using glucuronic acid (GlcA) significantly accelerates the mineralization process, which makes the process feasible for lab scale production of ormoHAP spheres and probably beyond. A further process was developed for gentle separation of the ormoHAP spheres from the gelatin gel without compromising the morphology of the mineral. The term ormoHAP was chosen since morphological analyses using electron microscopy (SEM, TEM) and element analysis (EDX, FT-IR, XRD) confirmed that carboxymethylated gelatin molecules use to act as organic templates for the formation of nanocrystalline HAP. The hydroxyapatite (HAP) crystals self-organize to form hollow spheres with diameters ranging from 100 to 500nm. The combination of the biocompatible chemical composition and the unique structure of the nanocomposites is considered to be a useful basis for future applications in functionalized degradable biomaterials. A novel bioinspired mineralization process was developed based on electric field-assisted migration of calcium and phosphate ions into biochemically carboxymethylated gelatin acting as organic template. Advantages over conventional hydroxyapatite include particle size distribution and homogeneity as well as achievable mechanical properties of relevant composites. Moreover, specifically developed calcium ion or phosphate ion release during degradation can be useful to adjust the fate of bone cells in order to manipulate remodeling processes. The hollow structure of the spheres can be useful for embedding drugs in the core, encapsulated by the highly mineralized outer shell. In this way, controlled drug release could be achieved, which enables

High resolution photoemission study of Nd1-xSrxMnO3

International Nuclear Information System (INIS)

Togashi, T.; Osawa, H.; Shin, S.; Tanaka, K.; Isozumi, Y.; Iwazumi, T.; Nozawa, S.

2004-01-01

Full text:Nd 1-x SrxMnO 3 shows the negative colossal magnetoresistance and various electronic phases. In order to reveal their states, we have performed a high- resolution Mn 2p-3d resonance photoemission (RPES) study of Nd 1-x SrxMnO 3 with an energy resolution of 100 meV at BL25SU in SPring-8. Figure 1 shows the Mn 2p-3d RPES spectra of Nd 1-x SrxMnO 3 . It is found that the spectral line shape in the ground-state phases (GS) at low temperatures is closely related to the shape of MnO 6 octahedra depending on x due to a static Jahn- Teller (JT) effect while the line shape in the paramagnetic insulator (PI) phase near room temperature is qualitatively similar to each other irrespective of x. These results strongly suggest that the dynamical and static JT effects are responsible for the 3d electronic states at high and low temperatures, respectively

Experimental investigation of nondipole effects in photoemission at the advanced light source

International Nuclear Information System (INIS)

Guillemin, Renaud; Hemmers, Oliver; Lindle, Dennis W.; Manson, Steven T.

2005-01-01

Breakdowns in the dipole approximation in the soft-X-ray photon-energy range (hν<5keV) were first observed 30 years ago and have been studied theoretically for many years. However, only recently their significance at low energies has been appreciated when advances in gas-phase-photoemission experiments using synchrotron radiation began to highlight numerous examples of significant nondipole effects at photon energies as low as tens of eV. In a previous publication [Hemmers et al., 2004a. Radiat. Phys. Chem. 70, 123-147], we presented a description of the recent advances made in the investigation of nondipole effects in photoionization from an experimental perspective. In this article, we report the results obtained by the X-ray atomic and molecular spectroscopy (XAMS) group at the Advanced Light Source, over the last 10 years, on the limits of the dipole approximation, probed by angle-resolved photoelectron spectroscopy for atoms and molecules in gas phase

Angle-resolved photoemission spectroscopy of rare earth LaSb{sub 2}

Energy Technology Data Exchange (ETDEWEB)

Michiardi, Matteo; Arnold, Fabian; Faerch Fisher, Karl Frederik; Svane, Axel; Bianchi, Marco; Brummerstedt Iversen, Bo; Hofmann, Philip [Aarhus University (Denmark); Shwetha, G.; Kanchana, V. [IIT-Hyderabad (India); Ganapathy, Vaitheeswaran [University of Hyderabad (India)

2016-07-01

Several rare earth diantimonides have been found to exhibit intriguing electronic properties such as anisotropic linear and non-saturating magnetoresistance. Among these materials, LaSb{sub 2} is not only considered for application in magnetoresistive devices but it is also found to be superconducting at low temperatures and it is investigated as candidate material to host charge density wave phases. Despite the several studies on its transport properties, the electronic structure of LaSb{sub 2} is still largely unknown. Here we present an angle-resolved photoemission spectroscopy and ab-initio calculation study of LaSb{sub 2}(001). The observed band structure is found to be in good agreement with theoretical predictions. Our results reveal that LaSb{sub 2} is a semimetal with a strongly nested two-dimensional Fermi surface. The low energy spectrum is characterized by four massive hole pockets and by four shallow, strongly directional, electron pockets that exhibit Dirac-like dispersion. We speculate on the possibility that this peculiar electronic structure drives the magnetoresistance to its quantum limit, explaining its unconventional behavior.

Below-threshold harmonic generation from strong non-uniform fields

Science.gov (United States)

Yavuz, I.

2017-10-01

Strong-field photoemission below the ionization threshold is a rich/complex region where atomic emission and harmonic generation may coexist. We studied the mechanism of below-threshold harmonics (BTH) from spatially non-uniform local fields near the metallic nanostructures. Discrete harmonics are generated due to the broken inversion symmetry, suggesting enriched coherent emission in the vuv frequency range. Through the numerical solution of the time-dependent Schrödinger equation, we investigate wavelength and intensity dependence of BTH. Wavelength dependence identifies counter-regular resonances; individual contributions from the multi-photon emission and channel-closing effects due to quantum path interferences. In order to understand the underlying mechanism of BTH, we devised a generalized semi-classical model, including the influence of Coulomb and non-uniform field interactions. As in uniform fields, Coulomb potential in non-uniform fields is the determinant of BTH; we observed that the generation of BTH are due to returning trajectories with negative energies. Due to large distance effectiveness of the non-uniformity, only long trajectories are noticeably affected.

Investigating the Effect of Nanoscale Changes on the Chemistry and Energetics of Nanocrystals with a Novel Photoemission Spectroscopy Methodology

Science.gov (United States)

Liao, Michael W.

This dissertation explores the effect of nanometer-scale changes in structure on the energetics of photocatalytic and photovoltaic materials. Of particular interest are semiconductor nanocrystals (NCs), which have interesting chemical properties that lead to novel structures and applications. Chief among these properties are quantum confinement and the high surface area-to-volume ratio, which allow for chemical tuning of the energetics and structure of NCs. This tunable energetic landscape has led to increasing application of NCs in various areas of research, including solar energy conversion, light-emitting diode technologies, and photocatalysis. However, spectroscopic methods to determine the energetics of NCs have not been well developed, due to chemical complexities of relevant NCs such as polydispersity, capping ligand effects, core-shell structures, and other chemical modifications. In this work, we demonstrate and expand the utility of photoelectron spectroscopy (PES) to probe the energetics of NCs by considering the physical processes that lead to background and secondary photoemission to enhance photoemission from the sample of interest. A new methodology for the interpretation of UP spectra was devised in order to emphasize the minute changes to the UP spectra line shape that arise from nanoscopic changes to the NCs. We applied various established subtractions that correct for photon source satellites, secondary photoelectrons, and substrate photoemission. We then investigated the effect of ligand surface coverage on the surface chemistry and density of states at the top of valence band (VB). We systematically removed ligands by increasing numbers of purification steps for two diameters of NCs and found that doing so increased photoemission density at the top of the VB, which is due to undercoordinated surface atoms. Deeper VB structure was also altered, possibly due to reorganization of the atoms in the NC. Using the new UPS interpretation methodology

Electronic structure of the dilute magnetic semiconductor G a1 -xM nxP from hard x-ray photoelectron spectroscopy and angle-resolved photoemission

Science.gov (United States)

Keqi, A.; Gehlmann, M.; Conti, G.; Nemšák, S.; Rattanachata, A.; Minár, J.; Plucinski, L.; Rault, J. E.; Rueff, J. P.; Scarpulla, M.; Hategan, M.; Pálsson, G. K.; Conlon, C.; Eiteneer, D.; Saw, A. Y.; Gray, A. X.; Kobayashi, K.; Ueda, S.; Dubon, O. D.; Schneider, C. M.; Fadley, C. S.

2018-04-01

We have investigated the electronic structure of the dilute magnetic semiconductor (DMS) G a0.98M n0.02P and compared it to that of an undoped GaP reference sample, using hard x-ray photoelectron spectroscopy (HXPS) and hard x-ray angle-resolved photoemission spectroscopy (HARPES) at energies of about 3 keV. We present experimental data, as well as theoretical calculations, to understand the role of the Mn dopant in the emergence of ferromagnetism in this material. Both core-level spectra and angle-resolved or angle-integrated valence spectra are discussed. In particular, the HARPES experimental data are compared to free-electron final-state model calculations and to more accurate one-step photoemission theory. The experimental results show differences between G a0.98M n0.02P and GaP in both angle-resolved and angle-integrated valence spectra. The G a0.98M n0.02P bands are broadened due to the presence of Mn impurities that disturb the long-range translational order of the host GaP crystal. Mn-induced changes of the electronic structure are observed over the entire valence band range, including the presence of a distinct impurity band close to the valence-band maximum of the DMS. These experimental results are in good agreement with the one-step photoemission calculations and a prior HARPES study of G a0.97M n0.03As and GaAs [Gray et al., Nat. Mater. 11, 957 (2012), 10.1038/nmat3450], demonstrating the strong similarity between these two materials. The Mn 2 p and 3 s core-level spectra also reveal an essentially identical state in doping both GaAs and GaP.

Controllable deposition of gadolinium doped ceria electrolyte films by magnetic-field-assisted electrostatic spray deposition

International Nuclear Information System (INIS)

Ksapabutr, Bussarin; Chalermkiti, Tanapol; Wongkasemjit, Sujitra; Panapoy, Manop

2013-01-01

This paper describes a simple and low-temperature approach to fabrication of dense and crack-free gadolinium doped ceria (GDC) thin films with controllable deposition by a magnetic-field-assisted electrostatic spray deposition technique. The influences of external permanent magnets on the deposition of GDC films were investigated. The coating area deposited using two magnets with the same pole arrangement decreased in comparison with the case of no magnets, whereas the largest deposition area was obtained in the system of the opposite poles. Analysis of as-deposited films at 450 °C indicated the formation of uniform, smooth and dense thin films with a single-phase fluorite structure. The films produced in the system using same poles were thicker, smaller in crystallite size and smoother than those fabricated under other conditions. Additionally, the GDC film deposited using the same pole arrangement showed the maximum in electrical conductivity of about 2.5 × 10 −2 S/cm at a low operating temperature of 500 °C. - Highlights: • Magnetic-field-assisted electrostatic spray allows a controllable coating. • Dense, crack-free thin films were obtained at low process temperature of 450 °C. • Control of deposition, thickness and uniformity is easy to achieve simultaneously. • Films from the same pole were thicker, smaller in crystal size and smoother. • The maximum conductivity of doped ceria film was 2.5 × 10 −2 S/cm at 500 °C

Magnetization Switching of a Co /Pt Multilayered Perpendicular Nanomagnet Assisted by a Microwave Field with Time-Varying Frequency

Science.gov (United States)

Suto, Hirofumi; Kanao, Taro; Nagasawa, Tazumi; Mizushima, Koichi; Sato, Rie

2018-05-01

Microwave-assisted magnetization switching (MAS) is attracting attention as a method for reversing nanomagnets with a high magnetic anisotropy by using a small-amplitude magnetic field. We experimentally study MAS of a perpendicularly magnetized nanomagnet by applying a microwave magnetic field with a time-varying frequency. Because the microwave field frequency can follow the nonlinear decrease of the resonance frequency, larger magnetization excitation than that in a constant-frequency microwave field is induced, which enhances the MAS effect. The switching field decreases almost linearly as the start value of the time-varying microwave field frequency increases, and it becomes smaller than the minimum switching field in a constant-frequency microwave field. To obtain this enhancement of the MAS effect, the end value of the time-varying microwave field frequency needs to be almost the same as or lower than the critical frequency for MAS in a constant-frequency microwave field. In addition, the frequency change typically needs to take 1 ns or longer to make the rate of change slow enough for the magnetization to follow the frequency change. This switching behavior is qualitatively explained by the theory based on the macrospin model.

Investigation of electronic states of infinite-layer SrFeO2 epitaxial thin films by X-ray photoemission and absorption spectroscopies

International Nuclear Information System (INIS)

Chikamatsu, Akira; Matsuyama, Toshiya; Hirose, Yasushi; Kumigashira, Hiroshi; Oshima, Masaharu; Hasegawa, Tetsuya

2012-01-01

Highlights: ► Electronic states of infinite-layer SrFeO 2 films have been experimentally observed. ► Fe 3d states have higher densities of states in the valence-band region. ► Three peaks derived from Fe 3d states were observed in the conduction-band region. ► Indirect bandgap value was determined to be 1.3 eV. - Abstract: We investigated the electronic states of a single-crystal SrFeO 2 epitaxial thin film in the valence-band and conduction-band regions using synchrotron-radiation X-ray photoemission and absorption spectroscopies. Fe 2p–3d resonant photoemission measurements revealed that the Fe 3d states have higher densities of states at binding energies of 3–5 eV and 5–8.5 eV in the valence-band region. The O K-edge X-ray absorption spectrum exhibited three peaks in the Fe 3d-derived conduction band hybridized with O 2p states; these can be assigned to Fe 3d xy , 3d xz + 3d yz , and 3d x 2 –y 2 . In addition, the indirect bandgap value of the SrFeO 2 film was determined to be 1.3 eV by transmission and absorption spectroscopies.

Electric-field assisted switching of magnetization in perpendicularly magnetized (Ga,Mn)As films at high temperatures

Science.gov (United States)

Wang, Hailong; Ma, Jialin; Yu, Xueze; Yu, Zhifeng; Zhao, Jianhua

2017-01-01

The electric-field effects on the magnetism in perpendicularly magnetized (Ga,Mn)As films at high temperatures have been investigated. An electric-field as high as 0.6 V nm-1 is applied by utilizing a solid-state dielectric Al2O3 film as a gate insulator. The coercive field, saturation magnetization and magnetic anisotropy have been clearly changed by the gate electric-field, which are detected via the anomalous Hall effect. In terms of the Curie temperature, a variation of about 3 K is observed as determined by the temperature derivative of the sheet resistance. In addition, electrical switching of the magnetization assisted by a fixed external magnetic field at 120 K is demonstrated, employing the gate-controlled coercive field. The above experimental results have been attributed to the gate voltage modulation of the hole density in (Ga,Mn)As films, since the ferromagnetism in (Ga,Mn)As is carrier-mediated. The limited modulation magnitude of magnetism is found to result from the strong charge screening effect introduced by the high hole concentration up to 1.10  ×  1021 cm-3, while the variation of the hole density is only about 1.16  ×  1020 cm-3.

Development of a novel electric field-assisted modified hydrodynamic cavitation system for disintegration of waste activated sludge.

Science.gov (United States)

Jung, Kyung-Won; Hwang, Min-Jin; Yun, Yeo-Myeong; Cha, Min-Jung; Ahn, Kyu-Hong

2014-09-01

In this current study, we present a modified hydrodynamic cavitation device that combines an electric field to substitute for the chemical addition. A modified HC system is basically an orifice plate and crisscross pipe assembly, in which the crisscross pipe imparts some turbulence, which creates collision events. This study shows that for maximizing disintegration, combining HC system, which called electric field-assisted modified orifice plate hydrodynamic cavitation (EFM-HC) in this study, with an electric field is important. Various HC systems were compared in terms of disintegration of WAS, and, among them, the EFM-HC system exhibited the best performance with the highest disintegration efficiency of 47.0±2.0% as well as the destruction of WAS morphological characteristics. The experimental results clearly show that a conventional HC system was successfully modified. In addition, electric field has a great potential for efficient disintegration of WAS for as a additional option in a combination treatment. This study suggests continued research in this field may lead to an appropriate design for commercial use. Copyright © 2014 Elsevier B.V. All rights reserved.

Direct surface magnetometry with photoemission magnetic x-ray dichroism

Energy Technology Data Exchange (ETDEWEB)

Tobin, J.G.; Goodman, K.W. [Lawrence Berkeley National Lab., CA (United States); Schumann, F.O. [Pennsylvania State Univ., University Park, PA (United States)] [and others

1997-04-01

Element specific surface magnetometry remains a central goal of synchrotron radiation based studies of nanomagnetic structures. One appealing possibility is the combination of x-ray absorption dichroism measurements and the theoretical framework provided by the {open_quotes}sum rules.{close_quotes} Unfortunately, sum rule analysis are hampered by several limitations including delocalization of the final state, multi-electronic phenomena and the presence of surface dipoles. An alternative experiment, Magnetic X-Ray Dichroism in Photoelectron Spectroscopy, holds out promise based upon its elemental specificity, surface sensitivity and high resolution. Computational simulations by Tamura et al. demonstrated the relationship between exchange and spin orbit splittings and experimental data of linear and circular dichroisms. Now the authors have developed an analytical framework which allows for the direct extraction of core level exchange splittings from circular and linear dichroic photoemission data. By extending a model initially proposed by Venus, it is possible to show a linear relation between normalized dichroism peaks in the experimental data and the underlying exchange splitting. Since it is reasonable to expect that exchange splittings and magnetic moments track together, this measurement thus becomes a powerful new tool for direct surface magnetometry, without recourse to time consuming and difficult spectral simulations. The theoretical derivation will be supported by high resolution linear and circular dichroism data collected at the Spectromicroscopy Facility of the Advanced Light Source.

Angle-resolved photoemission studies of the superconducting gap symmetry in Fe-based superconductors

Directory of Open Access Journals (Sweden)

Y.-B. Huang

2012-12-01

Full Text Available The superconducting gap is the fundamental parameter that characterizes the superconducting state, and its symmetry is a direct consequence of the mechanism responsible for Cooper pairing. Here we discuss about angle-resolved photoemission spectroscopy measurements of the superconducting gap in the Fe-based high-temperature superconductors. We show that the superconducting gap is Fermi surface dependent and nodeless with small anisotropy, or more precisely, a function of the momentum location in the Brillouin zone. We show that while this observation seems inconsistent with weak coupling approaches for superconductivity in these materials, it is well supported by strong coupling models and global superconducting gaps. We also suggest that a smaller lifetime of the superconducting Cooper pairs induced by the momentum dependent interband scattering inherent to these materials could affect the residual density of states at low energies, which is critical for a proper evaluation of the superconducting gap.

Magnetic-field-assisted synthesis of Co{sub 3}O{sub 4} nanoneedles with superior electrochemical capacitance

Energy Technology Data Exchange (ETDEWEB)

Zhu, Tao; Xie, Yan; Zhang, Guoxiong; He, Zhenni; Lu, Yisheng; Guo, Haibo [Shanghai University, Department of Electronic Information Materials, School of Materials Science and Engineering (China); Lin, Chuan [GE Global Research, China Technology Center (China); Chen, Yigang, E-mail: yigangchen@shu.edu.cn [Shanghai University, Department of Electronic Information Materials, School of Materials Science and Engineering (China)

2015-12-15

Nanostructured Co{sub 3}O{sub 4} films have been deposited on nickel foam in a magnetic-field-assisted hydrothermal process followed by annealing in air. The magnetic field strength is varied to study its relationship with nanostructures, morphology, and electrochemical properties of the Co{sub 3}O{sub 4} electrodes. The Co{sub 3}O{sub 4} films synthesized in the weak magnetic fields consist of dispersed nanoneedles, which are different from clustered nanoneedles when the magnetic field is absent. Moreover, the magnetic fields (of several millitesla) induced substantial changes in the nanostructures and electrochemical properties of the Co{sub 3}O{sub 4} films. A possible formation mechanism of Co{sub 3}O{sub 4} nanoneedles is proposed by comparing the morphologies and nanostructures of the films synthesized with and without the magnetic fields. Among these electrodes, the optimal one has a high specific capacitance (970.8 F g{sup −1} at 0.5 A g{sup −1}), good power capability (847.5 F g{sup −1} at 6.0 A g{sup −1}), and an excellent retention ratio (93.7 % over 1000 cycles). All these impressive results demonstrate that magnetic fields may be an economic and effective tool in hydrothermal synthesis of Co{sub 3}O{sub 4} electrodes for high-performance supercapacitors.

Electronic structure of charge-density-wave state in quasi-2D KMo6O17 purple bronze characterized by angle resolved photoemission spectroscopy

Science.gov (United States)

Valbuena, M. A.; Avila, J.; Drouard, S.; Guyot, H.; Asensio, M. C.

2006-01-01

We report on an angle-resolved-photoemission spectroscopy (ARPES) investigation of layered quasi-two dimensional (2D) Molybdenum purple bronze KMo6O17 in order to study and characterizes the transition to a charge-density-wave (CDW) state. We have performed photoemission temperature dependent measurements cooling down from room temperature (RT) to 32 K, well below the Peierls transition for this material, with CDW transition temperature Tc =110 K. The spectra have been taken at a selected kF point of the Fermi surface (FS) that satisfies the nesting condition of the FS, looking for the characteristic pseudo-gap opening in this kind of materials. The pseudogap has been estimated and it result to be in agreement with our previous works. The shift to lower binding energy of crossing Fermi level ARPES feature have been also confirmed and studied as a function of temperature, showing a rough like BCS behaviour. Finally we have also focused on ARPES measurements along ΓM¯ high symmetry direction for both room and low temperature states finding some insight for ‘shadow’ or back folded bands indicating the new periodicity of real lattice after the CDW lattice distortion.

Electronic structure of the Ga1-xCr xN studied by high-energy photoemission spectroscopy

International Nuclear Information System (INIS)

Kim, J.J.; Makino, H.; Yao, T.; Takata, Y.; Kobayashi, K.; Yamamoto, T.; Hanada, T.; Cho, M.W.; Ikenaga, E.; Yabashi, M.; Miwa, D.; Nishino, Y.; Tamasaku, K.; Ishikawa, T.; Shin, S.

2005-01-01

Valence band spectra of Ga 1-x Cr x N have been investigated by high-energy photoemission spectroscopy at the photon energy of 5.95 keV. Cr doping does introduce a novel electronic structure in the bandgap and causes some change in valence band structure. Based on the first-principle calculation, Cr-associated electronic levels in the bandgap are assigned to nonbonding and antibonding d states while the change of the valence band suggests that the Ga 4s originated states are significantly modified through hybridization with the Cr 3d orbital. The present result evidences that the Ga valence electrons are considerably modified through the interaction with the second nearest-neighbour Cr atoms

Time-resolved photoemission spectroscopy of electronic cooling and localization in CH3NH3PbI3 crystals

Science.gov (United States)

Chen, Zhesheng; Lee, Min-i.; Zhang, Zailan; Diab, Hiba; Garrot, Damien; Lédée, Ferdinand; Fertey, Pierre; Papalazarou, Evangelos; Marsi, Marino; Ponseca, Carlito; Deleporte, Emmanuelle; Tejeda, Antonio; Perfetti, Luca

2017-09-01

We measure the surface of CH3NH3PbI3 single crystals by making use of two-photon photoemission spectroscopy. Our method monitors the electronic distribution of photoexcited electrons, explicitly discriminating the initial thermalization from slower dynamical processes. The reported results disclose the fast-dissipation channels of hot carriers (0.25 ps), set an upper bound to the surface-induced recombination velocity (PbI3 samples is consistent with the progressive reduction of photoconversion efficiency in operating devices. Minimizing the density of shallow traps and solving the aging problem may boost the macroscopic efficiency of solar cells to the theoretical limit.

Electron-electron correlation, resonant photoemission and X-ray emission spectra

International Nuclear Information System (INIS)

Parlebas, J.C.; Kotani, Akio; Tanaka, Satoshi.

1991-01-01

In this short review paper we essentially focus on the high energy spectroscopies which involve second order quantum processes, i.e., resonance photoemission, Auger and X-ray emission spectroscopies, denoted respectively by RXPS, AES and XES. First, we summarize the main 3p-RXPS and AES results obtained in Cu and Ni metals; especially we recall that the satellite near the 3p-threshold in the spectra, which arises from a d-hole pair bound state, needs a careful treatment of the electron-electron correlation. Then we analyze the RXPS spectra in a few Ce compounds (CeO 2 , Ce 2 O 3 and CeF 3 ) involving 3d or 4d core levels and we interpret the spectra consistently with the other spectroscopies, such as core XPS and XAS which are first order quantum processes. Finally within the same one-impurity model and basically with the same sets of parameters, we review a theory for the Ce 5p→3d XES, as well as for the corresponding RXES, where (1) the incident X-ray is tuned to resonate with the 3d→4f transition and (2) the X-ray emission due to the 5p→3d transition is actually observed. The paper ends with a general discussion. (author) 77 refs

Dimensional Crossover in a Charge Density Wave Material Probed by Angle-Resolved Photoemission Spectroscopy

Science.gov (United States)

Nicholson, C. W.; Berthod, C.; Puppin, M.; Berger, H.; Wolf, M.; Hoesch, M.; Monney, C.

2017-05-01

High-resolution angle-resolved photoemission spectroscopy data reveal evidence of a crossover from one-dimensional (1D) to three-dimensional (3D) behavior in the prototypical charge density wave (CDW) material NbSe3 . In the low-temperature 3D regime, gaps in the electronic structure are observed due to two incommensurate CDWs, in agreement with x-ray diffraction and electronic-structure calculations. At higher temperatures we observe a spectral weight depletion that approaches the power-law behavior expected in one dimension. From the warping of the quasi-1D Fermi surface at low temperatures, we extract the energy scale of the dimensional crossover. This is corroborated by a detailed analysis of the density of states, which reveals a change in dimensional behavior dependent on binding energy. Our results offer an important insight into the dimensionality of excitations in quasi-1D materials.

Simulation of angle-resolved photoemission spectra by approximating the final state by a plane wave: From graphene to polycyclic aromatic hydrocarbon molecules

Energy Technology Data Exchange (ETDEWEB)

Puschnig, Peter, E-mail: peter.puschnig@uni-graz.at; Lüftner, Daniel

2015-04-15

Highlights: • Computational study on angular dependent photoemission spectroscopy. • Graphene and polycyclic aromatic hydrocarbon molecules. • Plane wave final state approximation accounts for experimental findings. - Abstract: We present a computational study on the angular-resolved photoemission spectra (ARPES) from a number of polycyclic aromatic hydrocarbons and graphene. Our theoretical approach is based on ab-initio density functional theory and the one-step model where we greatly simplify the evaluation of the matrix element by assuming a plane wave for the final state. Before comparing our ARPES simulations with available experimental data, we discuss how typical approximations for the exchange-correlation energy affect orbital energies. In particular, we show that by employing a hybrid functional, considerable improvement can be obtained over semi-local functionals in terms of band widths and relative energies of π and σ states. Our ARPES simulations for graphene show that the plane wave final state approximation provides indeed an excellent description when compared to experimental band maps and constant binding energy maps. Furthermore, our ARPES simulations for a number of polycyclic aromatic molecules from the oligo-acene, oligo-phenylene, phen-anthrene families as well as for disc-shaped molecules nicely illustrate the evolution of the electronic structure from molecules with increasing size towards graphene.

Thickness-dependent change in the valence band offset of the SiO{sub 2}/Si interface studied using synchrotron-radiation photoemission spectroscopy

Energy Technology Data Exchange (ETDEWEB)

Toyoda, S., E-mail: toyoda.satoshi.4w@kyoto-u.ac.jp; Oshima, M. [Department of Applied Chemistry, The University of Tokyo, Bunkyo-ku, Tokyo 113-8656 (Japan)

2016-08-28

We have studied the thickness-dependent change in the valence band offset (VBO) of the SiO{sub 2}/Si(001) interface using synchrotron-radiation photoemission spectroscopy with soft and hard X-rays. The SiO{sub 2}-film thickness (T{sub ox}) and X-ray irradiation time (t{sub irrad}) were systematically parameterized to distinguish between the “intrinsic” T{sub ox} effects in the VBOs and the “extrinsic” differential charging phenomena in SiO{sub 2} films on Si substrates. The results revealed that at a spontaneous time (t{sub irrad} ≈ 5 s) that suppresses the differential charging phenomena as much as possible, the experimental VBO abruptly increases as a function of T{sub ox} and gradually saturates to the traditional VBO value range determined by the internal photoemission and photoconduction measurements. This effect is not attributed to the differential charging phenomena, but rather it is attributed to the “intrinsic” T{sub ox}-dependent change in the VBO. The two possible physical behaviors include electronic polarization and image charge. We have derived the electronic polarization contribution from experimental data by carefully describing the effects of the long-range image charges based on the classical dielectric-screening model.

Modeling of electron behaviors under microwave electric field in methane and air pre-mixture gas plasma assisted combustion

Science.gov (United States)

Akashi, Haruaki; Sasaki, K.; Yoshinaga, T.

2011-10-01

Recently, plasma-assisted combustion has been focused on for achieving more efficient combustion way of fossil fuels, reducing pollutants and so on. Shinohara et al has reported that the flame length of methane and air premixed burner shortened by irradiating microwave power without increase of gas temperature. This suggests that electrons heated by microwave electric field assist the combustion. They also measured emission from 2nd Positive Band System (2nd PBS) of nitrogen during the irradiation. To clarify this mechanism, electron behavior under microwave power should be examined. To obtain electron transport parameters, electron Monte Carlo simulations in methane and air mixture gas have been done. A simple model has been developed to simulate inside the flame. To make this model simple, some assumptions are made. The electrons diffuse from the combustion plasma region. And the electrons quickly reach their equilibrium state. And it is found that the simulated emission from 2nd PBS agrees with the experimental result. Recently, plasma-assisted combustion has been focused on for achieving more efficient combustion way of fossil fuels, reducing pollutants and so on. Shinohara et al has reported that the flame length of methane and air premixed burner shortened by irradiating microwave power without increase of gas temperature. This suggests that electrons heated by microwave electric field assist the combustion. They also measured emission from 2nd Positive Band System (2nd PBS) of nitrogen during the irradiation. To clarify this mechanism, electron behavior under microwave power should be examined. To obtain electron transport parameters, electron Monte Carlo simulations in methane and air mixture gas have been done. A simple model has been developed to simulate inside the flame. To make this model simple, some assumptions are made. The electrons diffuse from the combustion plasma region. And the electrons quickly reach their equilibrium state. And it is found

General theoretical description of angle-resolved photoemission spectroscopy of van der Waals structures

Science.gov (United States)

Amorim, B.

2018-04-01

We develop a general theory to model the angle-resolved photoemission spectroscopy (ARPES) of commensurate and incommensurate van der Waals (vdW) structures, formed by lattice mismatched and/or misaligned stacked layers of two-dimensional materials. The present theory is based on a tight-binding description of the structure and the concept of generalized umklapp processes, going beyond previous descriptions of ARPES in incommensurate vdW structures, which are based on continuous, low-energy models, being limited to structures with small lattice mismatch/misalignment. As applications of the general formalism, we study the ARPES bands and constant energy maps for two structures: twisted bilayer graphene and twisted bilayer MoS2. The present theory should be useful in correctly interpreting experimental results of ARPES of vdW structures and other systems displaying competition between different periodicities, such as two-dimensional materials weakly coupled to a substrate and materials with density wave phases.

First-principles photoemission spectroscopy in DNA and RNA nucleobases from Koopmans-compliant functionals

Science.gov (United States)

Nguyen, Ngoc Linh; Borghi, Giovanni; Ferretti, Andrea; Marzari, Nicola

The determination of spectral properties of the DNA and RNA nucleobases from first principles can provide theoretical interpretation for experimental data, but requires complex electronic-structure formulations that fall outside the domain of applicability of common approaches such as density-functional theory. In this work, we show that Koopmans-compliant functionals, constructed to enforce piecewise linearity in energy functionals with respect to fractional occupation-i.e., with respect to charged excitations-can predict not only frontier ionization potentials and electron affinities of the nucleobases with accuracy comparable or superior with that of many-body perturbation theory and high-accuracy quantum chemistry methods, but also the molecular photoemission spectra are shown to be in excellent agreement with experimental ultraviolet photoemsision spectroscopy data. The results highlight the role of Koopmans-compliant functionals as accurate and inexpensive quasiparticle approximations to the spectral potential, which transform DFT into a novel dynamical formalism where electronic properties, and not only total energies, can be correctly accounted for.

Start-up assist by magnetized plasma flow injection in TPE-RX reversed-field pinch

Energy Technology Data Exchange (ETDEWEB)

Asai, T. [College of Science and Technology, Nihon University, 1-8 Kanda-Surugadai, Chiyoda-ku, Tokyo 101-8308 (Japan)]. E-mail: asai@phys.cst.nihon-u.ac.jp; Nagata, M. [Graduate School of Engineering, University of Hyogo, Himeji (Japan); Koguchi, H. [National Institute of Advanced Industrial Science and Technology (AIST), Tsukuba (Japan); Hirano, Y. [National Institute of Advanced Industrial Science and Technology (AIST), Tsukuba (Japan); Sakakita, H. [National Institute of Advanced Industrial Science and Technology (AIST), Tsukuba (Japan); Yambe, K. [National Institute of Advanced Industrial Science and Technology (AIST), Tsukuba (Japan); Kiyama, S. [National Institute of Advanced Industrial Science and Technology (AIST), Tsukuba (Japan)

2006-11-15

A reversed-field pinch (RFP) start-up assisted by a magnetized plasma flow injection was demonstrated for the first time on a TPE-RX machine. This sequence of experiments aimed to establish a new method of ionization, gas-fill and helicity injection in the start-up phase of an RFP. In this start-up method, magnetized and well-ionized plasma is formed by a magnetized coaxial plasma gun and injected into the torus chamber as an initial pre-ionized plasma for RFP formation. In the initial experiments, attenuated density pump-out and comparatively slow decay of the toroidal flux and plasma current were observed as evidence of its being an effective start-up method.

Studies of magnetism and exchange scattering in solids using synchrotron radiation and spin polarized photoemission. Final technical report, June 1, 1981-May 31, 1984

International Nuclear Information System (INIS)

Rothberg, G.M.

1984-01-01

Progress has been made toward developing Spin Polarized EXAFS (SPEXAFS) as a technique for studying magnetism in solids. The first observations have been made of EXAFS by means of photoemission with sufficient data to permit a traditional Fourier-transform analysis of atomic structure. Some of the advantages of photoelectron detection of EXAFS are: (1) vuv light may be used thereby extending greatly the useable range of photon energies; (2) the number of elements that may be studied for surface EXAFS is increased; (3) the possibility exists for measurements that cannot be done in other ways. In addition to its intrinsic interest, this result is crucial to the study of the spin dependence of EXAFS. These measurements were carried out on the vuv storage ring at the National Synchrotron Light Source. Data obtained on the spin dependence of EXAFS in MnF 2 at room temperature tentatively show dependence of the Mn absorber atom phase shift on the exchange interaction within the absorber atom. This effect has not been discussed theoretically. Preliminary observations have been made of the Fano resonance in Mn 3d photoemission at the 3p to 3d threshold

A Personal Digital Assistant (PDA) system for data acquisition during shoreline assessment field surveys

International Nuclear Information System (INIS)

Lamarche, A.; Owens, E.H.; Laflamme, A.; Laforest, S.; Clement, S.

2004-01-01

The Shoreline Cleanup Assessment Technique (SCAT) is a recognized method in North America to collect shoreline information and report observations on an oil spill. The long processing time required to analyze SCAT observations sometimes causes delays in oil spill response. Computerized systems have been developed to address this problem, but data entry of SCAT within such system involves much effort and is subject to potential errors. This paper described the development of a tool dedicated to the field capture of SCAT data on a Windows CE based Personal Digital Assistant (PDA). The system is compatible with both the SCAT methodology and Global Positioning System technology. A prototype of the system was tested during oil spills in Ontario and Nova Scotia. This paper described how the field data collection system was designed, developed and tested. Details of some user interfaces were provided to demonstrate how the large paper Shoreline Oiling Summary forms were made to fit on the small display screen of pocket-size devices. 8 refs., 1 tab., 12 figs

Angle-resolved photoemission spectroscopy with 9-eV photon-energy pulses generated in a gas-filled hollow-core photonic crystal fiber

OpenAIRE

Bromberger, H.; Ermolov, A.; Belli, F.; Liu, H.; Calegari, F.; Chavez-Cervantes, M.; Li, M. T.; Lin, C. T.; Abdolvand, A.; Russell, P. St. J.; Cavalleri, A.; Travers, J. C.; Gierz, I.

2015-01-01

A recently developed source of ultraviolet radiation, based on optical soliton propagation in a gas-filled hollow-core photonic crystal fiber, is applied here to angle-resolved photoemission spectroscopy (ARPES). Near-infrared femtosecond pulses of only few {\\mu}J energy generate vacuum ultraviolet (VUV) radiation between 5.5 and 9 eV inside the gas-filled fiber. These pulses are used to measure the band structure of the topological insulator Bi2Se3 with a signal to noise ratio comparable to ...

Theoretical modeling of the plasma-assisted catalytic growth and field emission properties of graphene sheet

International Nuclear Information System (INIS)

Sharma, Suresh C.; Gupta, Neha

2015-01-01

A theoretical modeling for the catalyst-assisted growth of graphene sheet in the presence of plasma has been investigated. It is observed that the plasma parameters can strongly affect the growth and field emission properties of graphene sheet. The model developed accounts for the charging rate of the graphene sheet; number density of electrons, ions, and neutral atoms; various elementary processes on the surface of the catalyst nanoparticle; surface diffusion and accretion of ions; and formation of carbon-clusters and large graphene islands. In our investigation, it is found that the thickness of the graphene sheet decreases with the plasma parameters, number density of hydrogen ions and RF power, and consequently, the field emission of electrons from the graphene sheet surface increases. The time evolution of the height of graphene sheet with ion density and sticking coefficient of carbon species has also been examined. Some of our theoretical results are in compliance with the experimental observations

Unoccupied electronic state of delafossite-type PdCoO2 single crystal probed using inverse photoemission spectroscopy

International Nuclear Information System (INIS)

Higuchi, Tohru; Tsukamoto, Takeyo; Hasegawa, Masashi; Tanaka, Masayuki; Takei, Humihiko; Shin, Shik

2004-01-01

The unoccupied electronic state of delafossite-type PdCoO 2 has been studied using inverse-photoemission spectroscopy (IPES). The Fermi edge and the unoccupied density-of-state (DOS) at the Fermi level (E F ) are not observed in the IPES spectrum measured at the incidence electron energy (E K ) of 100 eV, which corresponds to the Cooper minimum of Pd 4d. The finite DOS at E F is observed in the IPES spectra measured at the lower E K , which the ionization cross section of Pd 4d increases. These findings indicate that the Pd 4d electron is closely related to the low electrical resistivity of PdCoO 2 . (author)

Assisted inflation from geometric tachyon

International Nuclear Information System (INIS)

Panigrahi, Kamal L.; Singh, Harvendra

2007-01-01

We study the effect of rolling of N D3-branes in the vicinity of NS5-branes. We find out that this system coupled with the four dimensional gravity gives the slow roll assisted inflation of the scalar field theory. Once again this expectation is exactly similar to that of N-tachyon assisted inflation on unstable D-branes

Personal Insights and Anecdotes about the Weatherization Assistance Program Process Field Study

Energy Technology Data Exchange (ETDEWEB)

Treitler, Inga [Anthropology Imagination, Inc., Knoxville, TN (United States)

2014-09-01

The present report is based on the research conducted for the Process Field Study between March and September 2011. The Process Field Study documents how Weatherization Assistance Program (WAP) services were delivered to clients, and the quality with which those services were delivered. The assessments were conducted by visiting 19 agencies in 19 states around the country interviewing agency managers, staff, and contractors; observing program intake along, with 43 audits, 45 measure installation and 37 final inspections; and conducting debriefing interviews with clients and weatherization staff following the observation of service delivery. In this report, we turn to detailed observations of a few field interactions. The client stories from our observations illustrate some of the ways clients and crew interact to build the success of the program, but shows there will always be unanticipated obstacles to building trust and getting the program to the public. Stories of staff and crew career paths indicate that weatherization technology and techniques are being learned and used by technicians out of the new home construction industry and that their new knowledge provides them with technical tools and methods that many hope to take back into the construction industry if and when they return. This report is organized according to the four stages of weatherization: intake, audit, installation, and inspection. It contributes to our understanding of the area where policy, environment, culture, and individual decisions influence social innovation. The anecdotes reveal the realities of implementing programs for the benefit of the greater good at minimal cost and sacrifice in times of ever restricting budgets. As the authors revisited their field notes and compiled memorable narratives to communicate the essence of the weatherization experience, they identified three key takeaways that summarize the major issues. First, in WAP as in all services there will always be

Resonant inelastic x-ray scattering and photoemission measurement of O2: Direct evidence for dependence of Rydberg-valence mixing on vibrational states in O 1s → Rydberg states

Science.gov (United States)

Gejo, T.; Oura, M.; Tokushima, T.; Horikawa, Y.; Arai, H.; Shin, S.; Kimberg, V.; Kosugi, N.

2017-07-01

High-resolution resonant inelastic x-ray scattering (RIXS) and low-energy photoemission spectra of oxygen molecules have been measured for investigating the electronic structure of Rydberg states in the O 1s → σ* energy region. The electronic characteristics of each Rydberg state have been successfully observed, and new assignments are made for several states. The RIXS spectra clearly show that vibrational excitation is very sensitive to the electronic characteristics because of Rydberg-valence mixing and vibronic coupling in O2. This observation constitutes direct experimental evidence that the Rydberg-valence mixing characteristic depends on the vibrational excitation near the avoided crossing of potential surfaces. We also measured the photoemission spectra of metastable oxygen atoms (O*) from O2 excited to 1s → Rydberg states. The broadening of the 4p Rydberg states of O* has been found with isotropic behavior, implying that excited oxygen molecules undergo dissociation with a lifetime of the order of 10 fs in 1s → Rydberg states.

Model of inductive plasma production assisted by radio-frequency wave in tokamaks

International Nuclear Information System (INIS)

Hasegawa, Makoto; Hanada, Kazuaki; Sato, Kohnosuke

2007-01-01

For initial plasma production, an induction electric field generated by applying voltage to a poloidal field (PF) coil system is used to produce a Townsend avalanche breakdown. When the avalanche margins are small, as for the International Thermonuclear Experimental Reactor (ITER) in which the induction electric field is about 0.3 V/m, the assistance of radio-frequency waves (RF) is provided to reduce the induction electric field required for reliable breakdown. However, the conditions of RF-assisted breakdown are not clear. Here, the effects of both RF and induction electric field on the RF-assisted breakdown are evaluated considering the electron loss. When traveling loss is the dominant loss, a simple model of an extended Townsend avalanche is proposed. In this model, the induction electric field required for RF-assisted breakdown can be decreased to half that required for induction breakdown. (author)

Investigation of electronic states of infinite-layer SrFeO{sub 2} epitaxial thin films by X-ray photoemission and absorption spectroscopies

Energy Technology Data Exchange (ETDEWEB)

Chikamatsu, Akira, E-mail: chikamatsu@chem.s.u-tokyo.ac.jp [Department of Chemistry, University of Tokyo, Tokyo 113-0033 (Japan); Matsuyama, Toshiya [Department of Chemistry, University of Tokyo, Tokyo 113-0033 (Japan); Hirose, Yasushi [Department of Chemistry, The University of Tokyo, Tokyo 113-0033 (Japan); Kanagawa Academy of Science and Technology (KAST), Kawasaki 213-0012 (Japan); Kumigashira, Hiroshi; Oshima, Masaharu [Department of Applied Chemistry, University of Tokyo, Tokyo 113-8656 (Japan); Hasegawa, Tetsuya [Department of Chemistry, University of Tokyo, Tokyo 113-0033 (Japan); Kanagawa Academy of Science and Technology (KAST), Kawasaki 213-0012 (Japan)

2012-01-15

Highlights: Black-Right-Pointing-Pointer Electronic states of infinite-layer SrFeO{sub 2} films have been experimentally observed. Black-Right-Pointing-Pointer Fe 3d states have higher densities of states in the valence-band region. Black-Right-Pointing-Pointer Three peaks derived from Fe 3d states were observed in the conduction-band region. Black-Right-Pointing-Pointer Indirect bandgap value was determined to be 1.3 eV. - Abstract: We investigated the electronic states of a single-crystal SrFeO{sub 2} epitaxial thin film in the valence-band and conduction-band regions using synchrotron-radiation X-ray photoemission and absorption spectroscopies. Fe 2p-3d resonant photoemission measurements revealed that the Fe 3d states have higher densities of states at binding energies of 3-5 eV and 5-8.5 eV in the valence-band region. The O K-edge X-ray absorption spectrum exhibited three peaks in the Fe 3d-derived conduction band hybridized with O 2p states; these can be assigned to Fe 3d{sub xy}, 3d{sub xz} + 3d{sub yz}, and 3d{sub x}{sup 2}{sub -y}{sup 2}. In addition, the indirect bandgap value of the SrFeO{sub 2} film was determined to be 1.3 eV by transmission and absorption spectroscopies.

Resonant photoemission at the Ga 3p photothreshold in In xGa1-xN

International Nuclear Information System (INIS)

Colakerol, L.; Glans, P.-A.; Plucinski, L.; Zhang, Y.; Smith, K.E.; Zakharov, A.A.; Nyholm, R.; Cabalu, J.; Moustakas, T.D.

2006-01-01

Resonance effects at the Ga 3p photoabsorption threshold have been observed in photoemission spectra recorded from thin film In x Ga 1-x N alloys. The spectra display satellites of the main Ga 3d emission line, and the intensity of these satellites resonate at this threshold. The satellites are associated with a 3d 8 state, and have previously been observed for the semiconductors GaN, GaAs, and GaP. The resonance behavior has been studied for a variety of In x Ga 1-x N thin films with differing In concentration and band gap. The photon energy where the maximum resonance is observed varies with band gap within the alloy system, but does not follow the trend observed for binary Ga semiconducting compounds. We also observe that the threshold resonant energy increases slightly as the In content increases

Retention Characteristics of CBTi144 Thin Films Explained by Means of X-Ray Photoemission Spectroscopy

Directory of Open Access Journals (Sweden)

G. Biasotto

2010-01-01

Full Text Available CaBi4Ti4O15 (CBTi144 thin films were grown on Pt/Ti/SiO2/Si substrates using a soft chemical solution and spin-coating method. Structure and morphology of the films were characterized by the X-ray Diffraction (XRD, Fourier-transform infrared spectroscopy (FT-IR, Raman analysis, X-ray photoemission spectroscopy (XPS, and transmission electron microscopy (TEM. The films present a single phase of layered-structured perovskite with polar axis orient. The a/b-axis orientation of the ferroelectric film is considered to be associated with the preferred orientation of the Pt bottom electrode. XPS measurements were employed to understand the nature of defects on the retention behavior of CBTi144 films. We have observed that the main source of retention-free characteristic of the capacitors is the oxygen environment in the CBTi144 lattice.

Three Paradigms of Social Assistance

Directory of Open Access Journals (Sweden)

Pierre-Marc Daigneault

2014-11-01

Full Text Available “Ideas,” which are defined as the normative and cognitive beliefs of actors, are fundamental to a full understanding of the welfare state and, in particular, of social assistance. However, policy ideas have been neglected in most typologies of social assistance regimes. Based on a selective review of the literature, this article proposes a brief but systematic analysis of policy paradigms in the field of social assistance. Three ideal types that emphasize the ideational dimension of social assistance are analyzed, namely, the entitlement, workfare, and activation paradigms. The value of the typology lies in its utility for characterizing the ideational orientation of social assistance regimes. Specifically, the typology provides a yardstick for measuring the ideas of policy actors with respect to social assistance and can facilitate the conduct of case studies, comparative research, and causal analyses on this policy sector.

Soft x-ray photoemission spectroscopy of the Ba atomic layer deposition on the ceramic multiferroic BiFeO{sub 3}

Energy Technology Data Exchange (ETDEWEB)

Benemanskaya, G.V., E-mail: galina.benemanskaya@mail.ioffe.ru [Ioffe Institute, Politekhnicheskaya str. 26, St. Petersburg, 194021 (Russian Federation); Dementev, P.A.; Lapushkin, M.N. [Ioffe Institute, Politekhnicheskaya str. 26, St. Petersburg, 194021 (Russian Federation); Timoshnev, S.N. [St Petersburg Academic University, Khlopina str.8/3, St. Petersburg, 194021 (Russian Federation); Senkovskiy, B. [Helmholts-Zentrum Berlin, Elektronenspeicherring BESSY II, Albert-Einstein-Strasse 15, D-12489 Berlin (Germany)

2017-04-01

Highlights: • Ba/BiFeO{sub 3} interface was studied by X-ray synchrotron- photoemission spectroscopy. • Ba adsorption is found to modify the Bi 4f, O 1s and Fe 2p core level spectra. • Ba induced charge transfer causes increasing in Bi-valency and O-ionicity. • Ba adsorption results in increasing the amount of Fe{sup 2+} ions in the surface region. - Abstract: Electronic structure of the ceramic multiferroic BiFeO{sub 3} and the Ba/BiFeO{sub 3} nanointerface is investigated in situ in an ultrahigh vacuum by synchrotron-based photoemission spectroscopy with the excited photon energy from 120 eV to 900 eV. The Bi 4f, O 1s, Fe 2p, and Ba 5p core-levels spectra are studied. The Ba atomic layer deposition is found to induce a significant change in spectra that is originated from the charge transfer between Ba adatoms and Bi, O surface atoms with increasing the Bi-valency and O-ionicity. The Fe 2p{sub 3/2} core level spectrum for the clean BiFeO{sub 3} is shown to contain both the Fe{sup 2+} and Fe{sup 3+} ion components with the atomic ratio of Fe{sup 2+}/Fe{sup 3+} ∼1. The Ba adsorption is found to increase the ratio up to ∼1.5. This new effect is clearly caused by recharge between Fe{sup 3+} ↔ Fe{sup 2+} ions with increasing the amount of Fe{sup 2+} ions.

Angle-resolved-photoemission study of Bi2Sr2CaCu2O8+δ: Metallicity of the Bi-O plane

International Nuclear Information System (INIS)

Wells, B.O.; Shen, Z.; Dessau, D.S.; Spicer, W.E.; Olson, C.G.; Mitzi, D.B.; Kapitulnik, A.; List, R.S.; Arko, A.

1990-01-01

We have performed high-resolution angle-resolved-photoemission experiments on Bi 2 Sr 2 CaCu 2 O 8+δ single crystals with different annealing histories. By depositing a small amount of Au on the surface, we were able to distinguish electronic states associated with the Bi-O surface layer. We found that the Bi-O atomic surface layer is metallic and superconducting for samples that were high-temperature annealed in oxygen but not for as-grown samples. The Cu-O plane is found to be superconducting in all samples

Growth of metastable fcc Mn thin film on GaAs(001) and its electronic structure studied by photoemission with synchrotron radiation

International Nuclear Information System (INIS)

Chen Yan; Dong Guosheng; Zhang Ming

1995-01-01

The epitaxial growth of metastable fcc Mn thin films on GaAs(001) surface has been achieved at a substrate temperature of 400 K. The development of the fcc Mn thin films as a function of coverage is studied by photoemission with synchrotron radiation. The electron density of states below the Fermi edge of the fcc Mn phase is measured. A significant difference of the electronic structures is observed between the metastable fcc Mn phase and the thermodynamically stable α-Mn phase. Possible mechanisms are proposed to interpret the experimental result

High-resolution angle-resolved photoemission investigation of potassium and phosphate tungsten bronzes

International Nuclear Information System (INIS)

Paul, Sanhita; Kumari, Spriha; Raj, Satyabrata

2016-01-01

Highlights: • Electronic structure of potassium and phosphate tungsten bronzes. • Origin of transport anomalies in bronzes. • Flat segments of Fermi surfaces are connected by a nesting vector, q. • Nesting driven charge-density wave is responsible for the anomalies. - Abstract: We have performed high-resolution angle-resolved photoemission spectroscopy (ARPES) and density functional ab initio theoretical calculation to study the electronic structure of potassium (K_0_._2_5WO_3) and phosphate (P_4W_1_2O_4_4) tungsten bronzes. We have experimentally determined the band dispersions and Fermi surface topology of these bronzes and compared with our theoretical calculations and a fair agreement has been seen between them. Our experimental as well as theoretical investigation elucidates the origin of transport anomalies in these bronzes. The Fermi surfaces of these bronzes consist of flat patches, which can be connected with each other by a constant nesting wave vector, q. The scattering wave vectors found from diffraction measurements match with these nesting vectors and the anomalies in the transport properties of these bronzes can be well explained by the evolution of charge-density wave with a partial nesting between the flat segments of the Fermi surfaces.

Extracting the temperature of hot carriers in time- and angle-resolved photoemission

International Nuclear Information System (INIS)

Ulstrup, Søren; Hofmann, Philip; Johannsen, Jens Christian; Grioni, Marco

2014-01-01

The interaction of light with a material's electronic system creates an out-of-equilibrium (non-thermal) distribution of optically excited electrons. Non-equilibrium dynamics relaxes this distribution on an ultrafast timescale to a hot Fermi-Dirac distribution with a well-defined temperature. The advent of time- and angle-resolved photoemission spectroscopy (TR-ARPES) experiments has made it possible to track the decay of the temperature of the excited hot electrons in selected states in the Brillouin zone, and to reveal their cooling in unprecedented detail in a variety of emerging materials. It is, however, not a straightforward task to determine the temperature with high accuracy. This is mainly attributable to an a priori unknown position of the Fermi level and the fact that the shape of the Fermi edge can be severely perturbed when the state in question is crossing the Fermi energy. Here, we introduce a method that circumvents these difficulties and accurately extracts both the temperature and the position of the Fermi level for a hot carrier distribution by tracking the occupation statistics of the carriers measured in a TR-ARPES experiment

Extracting the temperature of hot carriers in time- and angle-resolved photoemission.

Science.gov (United States)

Ulstrup, Søren; Johannsen, Jens Christian; Grioni, Marco; Hofmann, Philip

2014-01-01

The interaction of light with a material's electronic system creates an out-of-equilibrium (non-thermal) distribution of optically excited electrons. Non-equilibrium dynamics relaxes this distribution on an ultrafast timescale to a hot Fermi-Dirac distribution with a well-defined temperature. The advent of time- and angle-resolved photoemission spectroscopy (TR-ARPES) experiments has made it possible to track the decay of the temperature of the excited hot electrons in selected states in the Brillouin zone, and to reveal their cooling in unprecedented detail in a variety of emerging materials. It is, however, not a straightforward task to determine the temperature with high accuracy. This is mainly attributable to an a priori unknown position of the Fermi level and the fact that the shape of the Fermi edge can be severely perturbed when the state in question is crossing the Fermi energy. Here, we introduce a method that circumvents these difficulties and accurately extracts both the temperature and the position of the Fermi level for a hot carrier distribution by tracking the occupation statistics of the carriers measured in a TR-ARPES experiment.

A photoemission study of evaporated manganese on gallium arsenide at elevated temperatures

International Nuclear Information System (INIS)

James, D.; Tadich, A.; Riley, J.; Leckey, R.; Emtsev, K.; Seyller, T.; Ley, L.

2004-01-01

Full text: The interaction between metals and semiconductors has been extensively researched to achieve an understanding of the formation of Schottky barriers and conditions for low resistance electrical connections to devices. The possibility of the use of magnetic materials to generate spin polarised currents, so called spintronics, and has extended this interest to metals that have not traditionally been used for such contacts. Manganese has recently been used as one element in GaAs and ZnSe based devices so its interaction with such surfaces is of interest. An interest that motivates this study is the possibility of lattice-matched growth of transition metal layers on semiconductors. Lattice mismatch initially appeared to inhibit single crystal transition metal growth, but it has been reported that lattice matched growth can occur in some cases. It is thought that reactions at the interface form a buffer layer, which allows for epitaxial growth via a more comparable lattice constant. We report studies of the growth of manganese films on GaAs(100) at several substrate temperatures using angle resolved photoemission, the diffusion of the Mn in the GaAs substrates using SIMS and the morphology of the layers using AFM images

Surface properties of SmB{sub 6} from X-ray photoemission spectroscopy

Energy Technology Data Exchange (ETDEWEB)

Heming, Nadine; Treske, Uwe; Knupfer, Martin; Koitzsch, Andreas [Institute for Solid State Research, IFW Dresden (Germany); Buechner, Bernd [Institute for Solid State Research, IFW Dresden (Germany); Institut fuer Festkoerperphysik, TU Dresden (Germany); Inosov, Dmytro [Institut fuer Festkoerperphysik, TU Dresden (Germany); Shitsevalova, Natalya Y.; Filipov, Volodymyr B. [Institute for Problems of Material Science, Kiev (Ukraine); Kraus, Stephan [BESSY II, Berlin (Germany)

2015-07-01

The mixed valence compound SmB{sub 6} has been well known for its anomalous low temperature resistivity behavior for decades: At temperatures below 50 K, SmB{sub 6} transmutes from a metal to an insulator but shows residual resistivity for temperatures less than 5 K. Renewed interest in this material comes from theoretical proposals, predicting topological protected surface states making this compound the prime candidate for the new material class of ''Topological Kondo Insulators''. Indeed, elaborate transport experiments have evidenced that the residual conductivity occurs only at the surface. However, it is generally well known that the surface of f-systems undergoes valence changes and reconstructions, which may also influence the surface properties of this material. Applying surface sensitive soft X-ray photoemission spectroscopy, we have investigated the surface properties of freshly cleaved SmB{sub 6} single crystals at 15 K monitoring the Sm valance, the chemical state of boron as well as the surface stoichiometry, and also the development of these over time and with increased temperature: We have found that the surface shows an unexpected complexity stemming from both intrinsic and extrinsic changes.

Adsorption of 3,4-ethylenedioxythiophene (EDOT) on noble metal surfaces: A photoemission and X-ray absorption study

International Nuclear Information System (INIS)

Pasquali, L.; Terzi, F.; Montecchi, M.; Doyle, B.P.; Lukkari, J.; Zanfrognini, B.; Seeber, R.; Nannarone, S.

2009-01-01

The adsorption of 3,4-ethylenedioxythiophene (EDOT) on Au and Pt surfaces is studied by core level and valence band photoemission using synchrotron radiation and by near edge X-ray absorption spectroscopy. To closer simulate real applications, the films are grown from aqueous solution at room temperature and are compared to an 'ideal' film prepared by dosing the molecules from the vapour phase on a clean Au(1 1 1) single crystal. The S 2p, C 1s and O 1s levels show multiple components which are associated to molecular fragmentation. NEXAFS confirms that fragmentation takes place at the surface. Thiophene species as well as alkyl chains and S n species are identified as the most probable fragmentation products.

Surface photovoltage investigation of gold chains on Si(111) by two-photon photoemission

Energy Technology Data Exchange (ETDEWEB)

Otto, Sebastian; Biedermann, Kerstin; Fauster, Thomas [Lehrstuhl fuer Festkoerperphysik, Universitaet Erlangen-Nuernberg, Staudtstr. 7, D-91058 Erlangen (Germany)

2011-07-01

We present surface photovoltage measurements on Si(111)-(7 x 7) with monoatomic gold chains. The gold coverage was varied between zero and 0.6 ML, where the Si(111)-(5 x 2)-Au reconstruction covers the surface completely. During the two-photon photoemission experiments the p- or n-doped samples were illuminated by infrared (IR, E{sub IR}=1.55 eV) and ultraviolet (UV, E{sub UV}=4.65 eV) laser pulses. For all coverages the photovoltage was determined for sample temperatures of 90 K and 300 K by variation of the IR and UV laser power. P-doped as well as n-doped Si(111) wafers show a linear dependence of the photovoltage on gold coverage. This stands in contrast to scanning tunneling spectroscopy measurements, which show a coverage-independent photovoltage over a wide coverage range for n-doped wafers. While for p-doped wafers our experimentally determined photovoltage is in agreement with previous reports, for n-doped wafers the observed values are lower than expected.

Quantum-memory-assisted entropic uncertainty relation in a Heisenberg XYZ chain with an inhomogeneous magnetic field

Science.gov (United States)

Wang, Dong; Huang, Aijun; Ming, Fei; Sun, Wenyang; Lu, Heping; Liu, Chengcheng; Ye, Liu

2017-06-01

The uncertainty principle provides a nontrivial bound to expose the precision for the outcome of the measurement on a pair of incompatible observables in a quantum system. Therefore, it is of essential importance for quantum precision measurement in the area of quantum information processing. Herein, we investigate quantum-memory-assisted entropic uncertainty relation (QMA-EUR) in a two-qubit Heisenberg \\boldsymbol{X}\\boldsymbol{Y}\\boldsymbol{Z} spin chain. Specifically, we observe the dynamics of QMA-EUR in a realistic model there are two correlated sites linked by a thermal entanglement in the spin chain with an inhomogeneous magnetic field. It turns out that the temperature, the external inhomogeneous magnetic field and the field inhomogeneity can lift the uncertainty of the measurement due to the reduction of the thermal entanglement, and explicitly higher temperature, stronger magnetic field or larger inhomogeneity of the field can result in inflation of the uncertainty. Besides, it is found that there exists distinct dynamical behaviors of the uncertainty for ferromagnetism \\boldsymbol{}≤ft(\\boldsymbol{J}\\boldsymbol{0}\\right) chains. Moreover, we also verify that the measuring uncertainty is dramatically anti-correlated with the purity of the bipartite spin system, the greater purity can result in the reduction of the measuring uncertainty, vice versa. Therefore, our observations might provide a better understanding of the dynamics of the entropic uncertainty in the Heisenberg spin chain, and thus shed light on quantum precision measurement in the framework of versatile systems, particularly solid states.

Synchronization and Characterization of an Ultra-Short Laser for Photoemission and Electron-Beam Diagnostics Studies at a Radio Frequency Photoinjector

Energy Technology Data Exchange (ETDEWEB)

Maxwell, Timothy; Ruan, Jinhao; Piot, Philippe; Lumpkin, Alex

2012-03-01

A commercially-available titanium-sapphire laser system has recently been installed at the Fermilab A0 photoinjector laboratory in support of photoemission and electron beam diagnostics studies. The laser system is synchronized to both the 1.3-GHz master oscillator and a 1-Hz signal use to trigger the radiofrequency system and instrumentation acquisition. The synchronization scheme and performance are detailed. Long-term temporal and intensity drifts are identified and actively suppressed to within 1 ps and 1.5%, respectively. Measurement and optimization of the laser's temporal profile are accomplished using frequency-resolved optical gating.

Fusion of Data from Heterogeneous Sensors with Distributed Fields of View and Situation Evaluation for Advanced Driver Assistance Systems

OpenAIRE

Otto, Carola

2013-01-01

In order to develop a driver assistance system for pedestrian protection, pedestrians in the environment of a truck are detected by radars and a camera and are tracked across distributed fields of view using a Joint Integrated Probabilistic Data Association filter. A robust approach for prediction of the system vehicles trajectory is presented. It serves the computation of a probabilistic collision risk based on reachable sets where different sources of uncertainty are taken into account.

Dynamics of spin-flip photon-assisted tunneling

NARCIS (Netherlands)

Braakman, F.R.; Danon, J.; Schreiber, L.R.; Wegscheider, W.; Vandersypen, L.M.K.

2014-01-01

We present time-resolved measurements of spin-flip photon-assisted tunneling and spin-flip relaxation in a doubly occupied double quantum dot. The photon-assisted excitation rate as a function of magnetic field indicates that spin-orbit coupling is the dominant mechanism behind the spin-flip under

[The Assistance maternelle de Montreal (1912-1961). An example of marginalization of philanthropic active women in the field of care for pregnants (French)].

Science.gov (United States)

Baillargeon, D

1999-01-01

This article examines the story of the Assistance maternelle de Montreal, an organization founded in 1912 by a group of bourgeois catholic women to provide material assistance and free medical services to poor pregnant mothers of the city. I want to show that even if the timid intervention of the Quebec state allowed the AM to survive during the almost 50 years, the rise of the experts in the health field--a phenomenon to which the AM has largely contributed--and in the philanthropic sector led to the marginalization of the female volunteers within the very institution they had created.

New developments in employee assistance programs.

Science.gov (United States)

White, R K; McDuff, D R; Schwartz, R P; Tiegel, S A; Judge, C P

1996-04-01

Employee assistance programs have developed from alcoholism assessment and referral centers to specialized behavioral health programs. Comprehensive employee assistance programs are defined by six major components: identification of problems based on job performance, consultation with supervisors, constructive confrontation, evaluation and referral, liaison with treatment providers, and substance abuse expertise. Other services have been added as enhancements to the basic model and include managed behavioral health activities and professional assistance committees, which provide services for impaired professionals and executives. Recent developments in the field are illustrated through examples from the experience of the employee assistance program at the University of Maryland Medical System in Baltimore.

Beam Dynamics Simulations of Optically-Enhanced Field Emission from Structured Cathodes

Energy Technology Data Exchange (ETDEWEB)

Seymour, A. [Northern Illinois U.; Grote, D. [LLNL, Livermore; Mihalcea, D. [Northern Illinois U.; Piot, P. [Fermilab; Vay, J.-L. [LBNL, Berkeley

2014-01-01

Structured cathodes - cathodes with a segmented emission surface - are finding an increasing number of applications and can be combined with a variety of emission mechanisms, including photoemission and field emission. These cathodes have been used to enhance the quantum efficiency of metallic cathodes when operated as plasmonic cathodes, have produced high-current electron bunches though field emission from multiple tips, and can be used to form beams with transverse segmentations necessary for improving the performance of accelerator-based light sources. In this report we present recent progress towards the development of finite-difference time-domain particle-in-cell simulations using the emission process in structured cathodes based on the WARP framework. The simulations give further insight on the localized source of the emitted electrons which could be used for additional high-fidelity start-to-end simulations of electron accelerators that employ this type of electron source.

Revisiting the role of trap-assisted-tunneling process on current-voltage characteristics in tunnel field-effect transistors

Science.gov (United States)

Omura, Yasuhisa; Mori, Yoshiaki; Sato, Shingo; Mallik, Abhijit

2018-04-01

This paper discusses the role of trap-assisted-tunneling process in controlling the ON- and OFF-state current levels and its impacts on the current-voltage characteristics of a tunnel field-effect transistor. Significant impacts of high-density traps in the source region are observed that are discussed in detail. With regard to recent studies on isoelectronic traps, it has been discovered that deep level density must be minimized to suppress the OFF-state leakage current, as is well known, whereas shallow levels can be utilized to control the ON-state current level. A possible mechanism is discussed based on simulation results.

Characterization of electronic structure of Cu2ZnSn(SxSe1−x)4 absorber layer and CdS/Cu2ZnSn(SxSe1−x)4 interfaces by in-situ photoemission and inverse photoemission spectroscopies

International Nuclear Information System (INIS)

Terada, Norio; Yoshimoto, Sho; Chochi, Kosuke; Fukuyama, Takayuki; Mitsunaga, Masahiro; Tampo, Hitoshi; Shibata, Hajime; Matsubara, Koji; Niki, Shigeru; Sakai, Noriyuki; Katou, Takuya; Sugimoto, Hiroki

2015-01-01

The dependences of electronic structure of CZTS x Se 1−x (CZTSSe) layers synthesized by sulfurization and/or selenization of the vacuum-deposited metal precursors on the anion mixing ratio x = S/(S + Se) have been studied by in-situ ultraviolet and X-ray photoemission spectroscopies (UPS, XPS) and inverse photoemission spectroscopy (IPES). The band alignment at interfaces between the CdS buffer by the sequential evaporation and the CZTSSe (x = 0.28 and 1.0) has also been investigated by the in-situ measurements of these spectroscopies. The UPS/IPES results of the CZTSSe surfaces have revealed linear expansion of band gap energy E g with an increase of x: E g(CZTSe;x=0) = 0.9-1.0 eV and E g(CZTS;x=1) = 1.5-1.6 eV. This expansion mainly originates in the rise of conduction band minimum CBM: CBM (CZTSe;x=0) = 0.45-0.50 eV and CBM (CZTS;x=1) = 0.95-1.05 eV. The in-situ measurements of the interface electronic structure have revealed that the CdS/CZTSSe (x = 0.28) interface has a so-called “type I” band alignment with a conduction band offset CBO about + 0.2 eV which is favorable to high cell performance. A negative CBO was distinguished for the CdS/CZTS (x = 1.0) interface, and the observed change in the band alignment with the anion mixing ratio was consistent with that of the variation in cell-performances. - Highlights: • The variation of electronic structure of CZTSSe films with S/(S + Se) ratio x is studied. • The monotonous rise of the conduction band minimum with x is clarified. • The band alignment at the CdS/CZTSSe interface is clarified by in-situ PES/IPES. • The change of the conduction band offset from positive to negative as an increase of x is observed. • The consistency between the band alignment and the cell performance is confirmed

Importance of semicore states in GW calculations for simulating accurately the photoemission spectra of metal phthalocyanine molecules.

Science.gov (United States)

Umari, P; Fabris, S

2012-05-07

The quasi-particle energy levels of the Zn-Phthalocyanine (ZnPc) molecule calculated with the GW approximation are shown to depend sensitively on the explicit description of the metal-center semicore states. We find that the calculated GW energy levels are in good agreement with the measured experimental photoemission spectra only when explicitly including the Zn 3s and 3p semicore states in the valence. The main origin of this effect is traced back to the exchange term in the self-energy GW approximation. Based on this finding, we propose a simplified approach for correcting GW calculations of metal phthalocyanine molecules that avoids the time-consuming explicit treatment of the metal semicore states. Our method allows for speeding up the calculations without compromising the accuracy of the computed spectra.

A high resolution photoemission study of surface core-level shifts in clean and oxygen-covered Ir(2 1 0) surfaces

Energy Technology Data Exchange (ETDEWEB)

Gladys, M.J.; Ermanoski, I.; Jackson, G.; Quinton, J.S.; Rowe, J.E.; Madey, T.E. E-mail: madey@physics.rutgers.edu

2004-04-01

High resolution soft X-ray photoemission electron spectroscopy (SXPS), using synchrotron radiation, is employed to investigate 4f core-level features of four differently-prepared Ir(2 1 0) surfaces: clean planar, oxygen-covered planar, oxygen-induced faceted, and clean faceted surfaces. Surface and bulk peak identifications are supported by measurements at different photon energies (thus probing different electron escape depths) and variable emission angles. Iridium 4f{sub 7/2} photoemission spectra are fitted with Doniach-Sunjic lineshapes. The surface components are identified with core levels positioned at lower binding energies than the bulk components, in contrast to previous reports of binding energy inversion on Ir(1 0 0) (1x1) and (5x1) surfaces. For clean planar Ir(2 1 0) three surface Ir 4f{sub 7/2} features are observed with core-level shifts of -765, -529, and -281 meV, with respect to the bulk; these are associated with the first, second and third layers of atoms, respectively, for atomically rough Ir(2 1 0). Adsorption of oxygen onto the planar Ir(2 1 0) surface is found to cause a suppression and shift of the surface features to higher binding energies. Annealing at T{>=}600 K in oxygen produces a faceted surface as verified by low energy electron diffraction (LEED). A comparison of planar and faceted oxygen-covered surfaces reveals minor differences in the normal emission SXPS spectra, while grazing emission spectra exhibit differences. The SXPS spectrum of the clean, faceted Ir(2 1 0) exhibits small differences in comparison to the clean planar case, with surface features having binding energy shifts of -710, -450, and -230 meV.

9th Ambient Assisted Living Congress

CERN Document Server

Mand, Beate

2017-01-01

In this book, leading authors in the field discuss the habitats of tomorrow. These habitats will be connected through autonomous and assistive systems, turning habitats into health resorts. This book discusses how assistance technologies enable a smooth transition from comfortable health support to medical or nursing care. The contributions have been chosen and invited at the 9th AAL congress, Frankfurt. .

Specialized instrument for radiation assistance teams

International Nuclear Information System (INIS)

Applegate, J.A.

1985-08-01

A specialized multiradiation instrument for radiation assistance teams (RAT's) has been designed; a working prototype has been constructed and field tested. The instrument detects alpha, beta, and gamma radiation simultaneously with simple red, yellow, and green meter indications and audio outputs. It is basically intended for DOE radiation assistance teams but would have application to any government, military, or industrial radiation accident team

Anomalous metallic state with strong charge fluctuations in BaxTi8O16 +δ revealed by hard x-ray photoemission spectroscopy

Science.gov (United States)

Dash, S.; Kajita, T.; Okawa, M.; Saitoh, T.; Ikenaga, E.; Saini, N. L.; Katsufuji, T.; Mizokawa, T.

2018-04-01

We have studied a charge-orbital driven metal-insulator transition (MIT) in hollandite-type BaxTi8O16 +δ by means of hard x-ray photoemission spectroscopy (HAXPES). The Ti 2 p HAXPES indicates strong Ti3 +/Ti4 + charge fluctuation in the metallic phase above the MIT temperature. The metallic phase is characterized by a power-law spectral function near the Fermi level which would be a signature of bad metal with non-Drude polaronic behavior. The power-law spectral shape is associated with the large Seebeck coefficient of the metallic phase in BaxTi8O16 +δ .

Unusually large chemical potential shift in a degenerate semiconductor: Angle-resolved photoemission study of SnSe and Na-doped SnSe

Science.gov (United States)

Maeda, M.; Yamamoto, K.; Mizokawa, T.; Saini, N. L.; Arita, M.; Namatame, H.; Taniguchi, M.; Tan, G.; Zhao, L. D.; Kanatzidis, M. G.

2018-03-01

We have studied the electronic structure of SnSe and Na-doped SnSe by means of angle-resolved photoemission spectroscopy. The valence-band top reaches the Fermi level by the Na doping, indicating that Na-doped SnSe can be viewed as a degenerate semiconductor. However, in the Na-doped system, the chemical potential shift with temperature is unexpectedly large and is apparently inconsistent with the degenerate semiconductor picture. The large chemical potential shift and anomalous spectral shape are key ingredients for an understanding of the novel metallic state with the large thermoelectric performance in Na-doped SnSe.

Atomistic modeling trap-assisted tunneling in hole tunnel field effect transistors

Science.gov (United States)

Long, Pengyu; Huang, Jun Z.; Povolotskyi, Michael; Sarangapani, Prasad; Valencia-Zapata, Gustavo A.; Kubis, Tillmann; Rodwell, Mark J. W.; Klimeck, Gerhard

2018-05-01

Tunnel Field Effect Transistors (FETs) have the potential to achieve steep Subthreshold Swing (S.S.) below 60 mV/dec, but their S.S. could be limited by trap-assisted tunneling (TAT) due to interface traps. In this paper, the effect of trap energy and location on OFF-current (IOFF) of tunnel FETs is evaluated systematically using an atomistic trap level representation in a full quantum transport simulation. Trap energy levels close to band edges cause the highest leakage. Wave function penetration into the surrounding oxide increases the TAT current. To estimate the effects of multiple traps, we assume that the traps themselves do not interact with each other and as a whole do not modify the electrostatic potential dramatically. Within that model limitation, this numerical metrology study points to the critical importance of TAT in the IOFF in tunnel FETs. The model shows that for Dit higher than 1012/(cm2 eV) IO F F is critically increased with a degraded IO N/IO F F ratio of the tunnel FET. In order to have an IO N/IO F F ratio higher than 104, the acceptable Dit near Ev should be controlled to no larger than 1012/(cm2 eV) .

Virtual tutor systems for robot-assisted instruction

Science.gov (United States)

Zhao, Zhijing; Zhao, Deyu; Zhang, Zizhen; Wei, Yongji; Qi, Bingchen; Okawa, Yoshikuni

2004-03-01

Virtual Reality technology belongs to advanced computer technology, it has been applied in instruction field and gains obvious effect. At the same time, robot assisted instruction comes true with the continuous development of Robot technology and artificial intelligence technology. This paper introduces a virtual tutor system for robot assisted instruction.

A study of Al/Si interface by photoemission, Auger electron yield and Auger electron spectroscopies

International Nuclear Information System (INIS)

Kobayashi, K.L.I.; Barth, J.; Gerken, F.; Kunz, C.; Deutsches Elektronen-Synchrotron

1980-06-01

Photoemission, Auger electron yield and Auger electron spectra were observed for Al/Si(111) interfaces with various Al coverage prepared by successive deposition using a molecular beam source. The Al 3p derived states are introduced at around the top of the valence band by the Al coverage of less than one monolayer. The Al surface layer behaves as a 'metal' and the Fermi level is stabilized in the Al 3p derived states at about 0.3 eV above the top of the valence band of Si. The Schottky barrier height in this stage is about 0.8 eV and further increase in Al coverage does not change the barrier height. A covalent bonding model of the Al/Si interface based on the experimental results is proposed. The present result favors the on-top geometry of Al atoms on Si(111) surface among the geometries used in the pseudopotential calculation by Zhang and Schlueter. (orig.)

Recent progress in energy-filtered high energy X-ray photoemission electron microscopy using a Wien filter type energy analyzer

International Nuclear Information System (INIS)

Niimi, H.; Tsutsumi, T.; Matsudaira, H.; Kawasaki, T.; Suzuki, S.; Chun, W.-J.; Kato, M.; Kitajima, Y.; Iwasawa, Y.; Asakura, K.

2004-01-01

Energy-filtered X-ray photoemission electron microscopy (EXPEEM) is a microscopy technique which has the potential to provide surface chemical mapping during surface chemical processes on the nanometer scale. We studied the possibilities of EXPEEM using a Wien filter type energy analyzer in the high energy X-ray region above 1000 eV. We have successfully observed the EXPEEM images of Au islands on a Ta sheet using Au 3d 5/2 and Ta 3d 5/2 photoelectron peaks which were excited by 2380 eV X-rays emitted from an undulator (BL2A) at Photon Factory. Our recent efforts to improve the sensitivity of the Wien filter energy analyzer will also be discussed

Space-charge effects in high-energy photoemission

Energy Technology Data Exchange (ETDEWEB)

Verna, Adriano, E-mail: adriano.verna@uniroma3.it [Dipartimento di Scienze, Università degli Studi Roma Tre, Via della Vasca Navale 84, I-00146 Roma (Italy); CNISM Unità di Roma Tre, Via della Vasca Navale 84, I-00146 Roma (Italy); Greco, Giorgia [Dipartimento di Scienze, Università degli Studi Roma Tre, Via della Vasca Navale 84, I-00146 Roma (Italy); Lollobrigida, Valerio [Dipartimento di Scienze, Università degli Studi Roma Tre, Via della Vasca Navale 84, I-00146 Roma (Italy); Scuola Dottorale in Matematica e Fisica, Università Roma Tre, Via della Vasca Navale 84, I-00146 Roma (Italy); Offi, Francesco; Stefani, Giovanni [Dipartimento di Scienze, Università degli Studi Roma Tre, Via della Vasca Navale 84, I-00146 Roma (Italy); CNISM Unità di Roma Tre, Via della Vasca Navale 84, I-00146 Roma (Italy)

2016-05-15

Highlights: • N-body simulations of interacting photoelectrons in hard X-ray experiments. • Secondary electrons have a pivotal role in determining the energy broadening. • Space charge has negligible effects on the photoelectron momentum distribution. • A simple model provides the characteristic time for energy-broadening mechanism. • The feasibility of time-resolved high-energy experiments with FELs is discussed. - Abstract: Pump-and-probe photoelectron spectroscopy (PES) with femtosecond pulsed sources opens new perspectives in the investigation of the ultrafast dynamics of physical and chemical processes at the surfaces and interfaces of solids. Nevertheless, for very intense photon pulses a large number of photoelectrons are simultaneously emitted and their mutual Coulomb repulsion is sufficiently strong to significantly modify their trajectory and kinetic energy. This phenomenon, referred as space-charge effect, determines a broadening and shift in energy for the typical PES structures and a dramatic loss of energy resolution. In this article we examine the effects of space charge in PES with a particular focus on time-resolved hard X-ray (∼10 keV) experiments. The trajectory of the electrons photoemitted from pure Cu in a hard X-ray PES experiment has been reproduced through N-body simulations and the broadening of the photoemission core-level peaks has been monitored as a function of various parameters (photons per pulse, linear dimension of the photon spot, photon energy). The energy broadening results directly proportional to the number N of electrons emitted per pulse (mainly represented by secondary electrons) and inversely proportional to the linear dimension a of the photon spot on the sample surface, in agreement with the literature data about ultraviolet and soft X-ray experiments. The evolution in time of the energy broadening during the flight of the photoelectrons is also studied. Despite its detrimental consequences on the energy

Space-charge effect in electron time-of-flight analyzer for high-energy photoemission spectroscopy

International Nuclear Information System (INIS)

Greco, G.; Verna, A.; Offi, F.; Stefani, G.

2016-01-01

Highlights: • Two methods for the simulation of space-charge effect in time-resolved PES. • Reliability and advantages in the use of the SIMION"® software. • Simulation of the space-charge effect in an electron TOF analyzer. • Feasibility of a TOF analyzer in time-resolved high-energy PES experiments at FEL. - Abstract: The space-charge effect, due to the instantaneous emission of many electrons after the absorption of a single photons pulse, causes distortion in the photoelectron energy spectrum. Two calculation methods have been applied to simulate the expansion during a free flight of clouds of mono- and bi-energetic electrons generated by a high energy pulse of light and their results have been compared. The accuracy of a widely used tool, such as SIMION"®, in predicting the energy distortion caused by the space-charge has been tested and the reliability of its results is verified. Finally we used SIMION"® to take into account the space-charge effects in the simulation of simple photoemission experiments with a time-of-flight analyzer.

High voltage performance of a dc photoemission electron gun with centrifugal barrel-polished electrodes

Science.gov (United States)

Hernandez-Garcia, C.; Bullard, D.; Hannon, F.; Wang, Y.; Poelker, M.

2017-09-01

The design and fabrication of electrodes for direct current (dc) high voltage photoemission electron guns can significantly influence their performance, most notably in terms of maximum achievable bias voltage. Proper electrostatic design of the triple-point junction shield electrode minimizes the risk of electrical breakdown (arcing) along the insulator-cable plug interface, while the electrode shape is designed to maintain work, we describe a centrifugal barrel-polishing technique commonly used for polishing the interior surface of superconducting radio frequency cavities but implemented here for the first time to polish electrodes for dc high voltage photoguns. The technique reduced polishing time from weeks to hours while providing surface roughness comparable to that obtained with diamond-paste polishing and with unprecedented consistency between different electrode samples. We present electrode design considerations and high voltage conditioning results to 360 kV (˜11 MV/m), comparing barrel-polished electrode performance to that of diamond-paste polished electrodes. Tests were performed using a dc high voltage photogun with an inverted-geometry ceramic insulator design.

Designing and Implementing an Assistive Technology Lab for Postsecondary Education

Science.gov (United States)

Jones, Beth; Williams, Nichole; Rudinger, Belinda

2018-01-01

A literature review discusses how teacher knowledge of assistive technology significantly impacts student success with assistive technology and that many teachers enter the field feeling unprepared to implement these technologies with students. This article explores one university's process in setting up an assistive technology laboratory for…

Field Testing of LIDAR-Assisted Feedforward Control Algorithms for Improved Speed Control and Fatigue Load Reduction on a 600-kW Wind Turbine: Preprint

Energy Technology Data Exchange (ETDEWEB)

Kumar, Avishek A.; Bossanyi, Ervin A.; Scholbrock, Andrew K.; Fleming, Paul; Boquet, Mathieu; Krishnamurthy, Raghu

2015-12-14

A severe challenge in controlling wind turbines is ensuring controller performance in the presence of a stochastic and unknown wind field, relying on the response of the turbine to generate control actions. Recent technologies such as LIDAR, allow sensing of the wind field before it reaches the rotor. In this work a field-testing campaign to test LIDAR Assisted Control (LAC) has been undertaken on a 600-kW turbine using a fixed, five-beam LIDAR system. The campaign compared the performance of a baseline controller to four LACs with progressively lower levels of feedback using 35 hours of collected data.

Comparison of field-enhanced and pressure-assisted field-enhanced sample injection techniques for the analysis of water-soluble vitamins using CZE.

Science.gov (United States)

Liu, Qingqing; Liu, Yaling; Guan, Yu; Jia, Li

2009-04-01

A new online concentration method, namely pressure-assisted field-enhanced sample injection (PA-FESI), was developed and compared with FESI for the analysis of water-soluble vitamins by CZE with UV detection. In PA-FESI, negative voltage and positive pressure were simultaneously applied to initialize PA-FESI. PA-FESI uses the hydrodynamic flow generated by the positive pressure to counterbalance the reverse EOF in the capillary column during electrokinetic sample injection, which allowed a longer injection time than usual FESI mode without compromising the separation efficiency. Using the PA-FESI method, the LODs of the vitamins were at ng/mL level based on the S/N of 3 and the RSDs of migration time and peak area for each vitamin (1 microg/mL) were less than 5.1%. The developed method was applied to the analysis of water-soluble vitamins in corns.

Active spectroscopic measurements of the bulk deuterium properties in the DIII-D tokamak (invited).

Science.gov (United States)

Grierson, B A; Burrell, K H; Chrystal, C; Groebner, R J; Kaplan, D H; Heidbrink, W W; Muñoz Burgos, J M; Pablant, N A; Solomon, W M; Van Zeeland, M A

2012-10-01

The neutral-beam induced D(α) emission spectrum contains a wealth of information such as deuterium ion temperature, toroidal rotation, density, beam emission intensity, beam neutral density, and local magnetic field strength magnitude |B| from the Stark-split beam emission spectrum, and fast-ion D(α) emission (FIDA) proportional to the beam-injected fast ion density. A comprehensive spectral fitting routine which accounts for all photoemission processes is employed for the spectral analysis. Interpretation of the measurements to determine physically relevant plasma parameters is assisted by the use of an optimized viewing geometry and forward modeling of the emission spectra using a Monte-Carlo 3D simulation code.

Surface-plasmon resonance-enhanced multiphoton emission of high-brightness electron beams from a nanostructured copper cathode.

Science.gov (United States)

Li, R K; To, H; Andonian, G; Feng, J; Polyakov, A; Scoby, C M; Thompson, K; Wan, W; Padmore, H A; Musumeci, P

2013-02-15

We experimentally investigate surface-plasmon assisted photoemission to enhance the efficiency of metallic photocathodes for high-brightness electron sources. A nanohole array-based copper surface was designed to exhibit a plasmonic response at 800 nm, fabricated using the focused ion beam milling technique, optically characterized and tested as a photocathode in a high power radio frequency photoinjector. Because of the larger absorption and localization of the optical field intensity, the charge yield observed under ultrashort laser pulse illumination is increased by more than 100 times compared to a flat surface. We also present the first beam characterization results (intrinsic emittance and bunch length) from a nanostructured photocathode.

Electronic properties of Mn-phthalocyanine–C60 bulk heterojunctions: Combining photoemission and electron energy-loss spectroscopy

International Nuclear Information System (INIS)

Roth, Friedrich; Herzig, Melanie; Knupfer, Martin; Lupulescu, Cosmin; Darlatt, Erik; Gottwald, Alexander; Eberhardt, Wolfgang

2015-01-01

The electronic properties of co-evaporated mixtures (blends) of manganese phthalocyanine and the fullerene C 60 (MnPc:C 60 ) have been studied as a function of the concentration of the two constituents using two supplementary electron spectroscopic methods, photoemission spectroscopy (PES) and electron energy-loss spectroscopy (EELS) in transmission. Our PES measurements provide a detailed picture of the electronic structure measured with different excitation energies as well as different mixing ratios between MnPc and C 60 . Besides a relative energy shift, the occupied electronic states of the two materials remain essentially unchanged. The observed energy level alignment is different compared to that of the related CuPc:C 60 bulk heterojunction. Moreover, the results from our EELS investigations show that, despite the rather small interface interaction, the MnPc related electronic excitation spectrum changes significantly by admixing C 60 to MnPc thin films

Electronic structure of heavy fermion system CePt2In7 from angle-resolved photoemission spectroscopy

International Nuclear Information System (INIS)

Shen Bing; Yu Li; Lyu Shou-Peng; Jia Xiao-Wen; Zhang Yan; Wang Chen-Lu; Hu Cheng; Ding Ying; Sun Xuan; Hu Yong; Liu Jing; Gao Qiang; Zhao Lin; Liu Guo-Dong; Liu Kai; Lu Zhong-Yi; Bauer, E D; Thompson, J D; Xu Zu-Yan; Chen Chuang-Tian

2017-01-01

We have carried out high-resolution angle-resolved photoemission measurements on the Ce-based heavy fermion compound CePt 2 In 7 that exhibits stronger two-dimensional character than the prototypical heavy fermion system CeCoIn 5 . Multiple Fermi surface sheets and a complex band structure are clearly resolved. We have also performed detailed band structure calculations on CePt 2 In 7 . The good agreement found between our measurements and the calculations suggests that the band renormalization effect is rather weak in CePt 2 In 7 . A comparison of the common features of the electronic structure of CePt 2 In 7 and CeCoIn 5 indicates that CeCoIn 5 shows a much stronger band renormalization effect than CePt 2 In 7 . These results provide new information for understanding the heavy fermion behaviors and unconventional superconductivity in Ce-based heavy fermion systems. (paper)

A photoemission study of Mn grown on GaAs(100)

International Nuclear Information System (INIS)

James, D.; Riley, J.; Leckey, R.; Usher, B.; Sieber, N.; Seyller, Th.; Ley, L.

2002-01-01

Full text: Metal contacts on semiconductors have been an important area for device manufacture. The possibility of lattice matched growth of magnetic metals on semiconductors was once thought to be a unobtainable goal. More recently it has been found that transition metals can react with the semiconductor substrates, forming another lattice with a more comparable lattice constant, from which epitaxial growth can then proceed. Al grows epitaxially on GaN even with a lattice mismatch greater than 10%. In this instance, Al displaces Ga being driven by a larger heat of formation to produce an AlN buffer layer, on which Al can then grow. This paper investigates the room temperature deposition of Mn onto GaAs(100) at room temperature. The Photoemission study was carried out at the UEL56/2 PGM2 beam line at BESSY II in Berlin, Germany. Synchrotron radiation was used to observe the surface as thin layers of Mn were deposited. The interaction of manganese with the substrate tends to donate electron density to neighbouring atoms, decreasing binding energy. No further segregation of substitutional or interstitial Mn and Ga can be seen from angle dependence data at this temperature, with metallic manganese eventually attenuating the bulk Ga signal to the point where it is indistinguishable from the background. It is concluded that there the metal reacts with the semiconductor surface with some indiffusion as confirmed using SIMS. Previously, the reaction was only thought to have taken place above room temperature. The resulting structure consists of a Ga-As-Mn buffer layer as with the higher temperature depositions

Spin-resolved x-ray photoemission studies of ferromagnetic metals

International Nuclear Information System (INIS)

Klebanoff, L.E.

1996-01-01

Recent spin-resolved x-ray photoelectron spectroscopy (SRXPS) studies of ferromagnetic metals are reviewed. SRXPS studies of metallic Fe, Co, Co 66 Fe 4 Ni 1 B 14 Si 15 , and Ni demonstrate that core-level photoemission, and the itinerant electron response to core-hole creation, are highly spin-dependent. The exchange splitting of the Fe 2p 3/2 level is found to be 0.48±0.05 eV. Lifetime broadening results for the Fe 2p 3/2 N↑ (majority spin) and N↓ (minority spin) components indicate conservation of spin in core-hole filling processes involving the valence band. SRXPS study of the Fe 2p 3/2 peak asymmetry α reveals a dependence of electron endash hole excitation on the spin of the core hole. Spin analysis of the Fe 3s XPS line shape shows it to be a three-component spectrum, rather than the two-component line shape assumed previously. A photon energy dependence of one of the Fe 3s components explains disagreement among previous Fe 3s XPS results. Comparisons of SRXPS from Co metal and Co 66 Fe 4 Ni 1 B 14 Si 15 directly demonstrate the effect of a reduced atomic magnetic moment on the spin dependence of core-level XPS. The behavior of lifetime broadenings for the N↑ and N↓ Co 2p 3/2 components show that the reduced Co magnetic moment found in the Co 66 Fe 4 Ni 1 B 14 Si 15 amorphous glass is due to the transfer of ↑-spin valence electron density to the ↓-spin valence band upon glass formation. SRXPS also allows investigation of spin-dependent core-hole screening processes and satellite production, as demonstrated in SRXPS studies of ferromagnetic Ni. Future directions of SRXPS are also explored. copyright 1996 American Vacuum Society

Current assisted superplastic forming of titanium alloy

Directory of Open Access Journals (Sweden)

Wang Guofeng

2015-01-01

Full Text Available Current assisted superplastic forming combines electric heating technology and superplastic forming technology, and can overcome some shortcomings of traditional superplastic forming effectively, such as slow heating rate, large energy loss, low production efficiency, etc. Since formability of titanium alloy at room temperature is poor, current assisted superplastic forming is suitable for titanium alloy. This paper mainly introduces the application of current assisted superplastic forming in the field of titanium alloy, including forming technology of double-hemisphere structure and bellows.

Performance of the inverse photoemission spectrometer with a new bandpass photon detector of narrow bandwidth and high sensitivity

International Nuclear Information System (INIS)

Ueda, Yoshifumi; Nishihara, Katsuhiro; Mimura, Kojiro; Hari, Yasuko; Taniguchi, Masaki; Fujisawa, Masami

1993-01-01

A combination of a SrF 2 entrance window and a photomultiplier with the Cu-BeO first dynode coated with KCl film realizes the bandpass photon detector with the FWHM of 0.47 eV centered at 9.43 eV and the sensitivity improved by about one order of magnitude in comparison with the detector without the KCl film. The overall energy resolution of the inverse photoemission spectrometer consisting of an electron gun with a BaO cathode and the new detector has been estimated to be 0.56 eV using polycrystalline Au. Typical counting rate is 10 2 -10 3 counts/(μA s) for unoccupied states near the Fermi level of the Au at an acceptance angle of about 0.8π sr with an Al collecting mirror. (orig.)

Real-time observation of template-assisted colloidal aggregation and colloidal dispersion under an alternating electric field

International Nuclear Information System (INIS)

Chao-Rong, Li; Shu-Wen, Li; Jie, Mei; Qing, Xu; Ying-Ying, Zheng; Wen-Jun, Dong

2011-01-01

A fascinating colloid phenomenon was observed in a specially designed template-assisted cell under an alternating electrical field. Most colloidal particles experienced the processes of aggregation, dispersion and climbing up to the plateaus of the patterns pre-lithographed on the indium tin oxide glass as the frequency of the alternating electrical field increased. Two critical frequencies f crit1 ≈ 15 kHz and f crit2 ≈ 40 kHz, corresponding to the transitions of the colloid behaviour were observed. When f < 15 kHz, the particles were forced to aggregate along the grooves of the negative photoresist patterned template. When 15 kHz < f < 40 kHz, the particle clusters became unstable and most particles started to disperse and were blocked by the fringes of the negative photoresist patterns. As the frequency increased to above 40 kHz, the majority of particles started to climb up to the plateaus of the patterns. Furthermore, the dynamics analysis for the behaviour of the colloids was given and we found out that positive or negative dielectrophoresis force, electrohydrodynamic force, particle—particle interactions and Brownian motion change with the frequency of the alternating electric field. Thus, changes of the related forces affect or control the behaviour of the colloids. (interdisciplinary physics and related areas of science and technology)

The development of photoemission spectroscopy and its application to the study of semiconductor interfaces Observations on the interplay between basic and applied research (Welch Memorial Lecture)

Science.gov (United States)

Spicer, W. E.

1985-01-01

A sketch is given of the development of photoemission electron spectroscopy (PES) with emphasis on the author's own experience. Emphasis is placed: (1) on the period between 1958-1970; (2) on the various developments which were required for PES to emerge; and (3) on the strong interactions between applied/fundamental and knowledge/empirically based research. A more detailed discussion is given of the recent (1975-present) application of PES to study the interfaces of III-V semiconductors.

Translational medicine in the field of ablative fractional laser (AFXL)-assisted drug delivery

DEFF Research Database (Denmark)

Haedersdal, Merete; Erlendsson, Andrés M; Paasch, Uwe

2016-01-01

Ablative fractional lasers enhance uptake of topical therapeutics and the concept of fractional laser-assisted drug delivery has now been taken into clinical practice. Objectives We systematically reviewed preclinical data and clinical evidence for fractional lasers to enhance drug uptake...... level of evidence was reached for actinic keratoses treated with methylaminolevulinate for photodynamic therapy (level IB, 5 randomized controlled trials), substantiating superior and long-lasting efficacy versus conventional photodynamic therapy. No adverse events were reported, but ablative fractional...... laser-assisted drug delivery implies risks of systemic drug absorption, especially when performed over large skin areas. Conclusions Fractional laser-assisted drug delivery is beneficial in enhancing preclinical and clinical outcomes for certain skin conditions....

Robotic assisted andrological surgery

Science.gov (United States)

Parekattil, Sijo J; Gudeloglu, Ahmet

2013-01-01

The introduction of the operative microscope for andrological surgery in the 1970s provided enhanced magnification and accuracy, unparalleled to any previous visual loop or magnification techniques. This technology revolutionized techniques for microsurgery in andrology. Today, we may be on the verge of a second such revolution by the incorporation of robotic assisted platforms for microsurgery in andrology. Robotic assisted microsurgery is being utilized to a greater degree in andrology and a number of other microsurgical fields, such as ophthalmology, hand surgery, plastics and reconstructive surgery. The potential advantages of robotic assisted platforms include elimination of tremor, improved stability, surgeon ergonomics, scalability of motion, multi-input visual interphases with up to three simultaneous visual views, enhanced magnification, and the ability to manipulate three surgical instruments and cameras simultaneously. This review paper begins with the historical development of robotic microsurgery. It then provides an in-depth presentation of the technique and outcomes of common robotic microsurgical andrological procedures, such as vasectomy reversal, subinguinal varicocelectomy, targeted spermatic cord denervation (for chronic orchialgia) and robotic assisted microsurgical testicular sperm extraction (microTESE). PMID:23241637

Preparation of solid-state samples of a transition metal coordination compound for synchrotron radiation photoemission studies

CERN Document Server

Crotti, C; Celestino, T; Fontana, S

2003-01-01

The aim of this research was to identify a sample preparation method suitable for the study of transition metal complexes by photoemission spectroscopy with synchrotron radiation as the X-ray source, even in the case where the compound is not evaporable. Solid-phase samples of W(CO) sub 4 (dppe) [dppe=1,2-bis(diphenylphosphino)ethane] were prepared according to different methods and their synchrotron radiation XPS spectra measured. The spectra acquired from samples prepared by spin coating show core level peaks only slightly broader than the spectrum recorded from UHV evaporated samples. Moreover, for these samples the reproducibility of the binding energy values is excellent. The dependence of the spin coating technique on parameters such as solvent and solution concentration, spinning speed and support material was studied. The same preparation method also allowed the acquisition of valence band spectra, the main peaks of which were clearly resolved. The results suggest that use of the spin coating techniqu...

Performance Evaluation Methods for Assistive Robotic Technology

Science.gov (United States)

Tsui, Katherine M.; Feil-Seifer, David J.; Matarić, Maja J.; Yanco, Holly A.

Robots have been developed for several assistive technology domains, including intervention for Autism Spectrum Disorders, eldercare, and post-stroke rehabilitation. Assistive robots have also been used to promote independent living through the use of devices such as intelligent wheelchairs, assistive robotic arms, and external limb prostheses. Work in the broad field of assistive robotic technology can be divided into two major research phases: technology development, in which new devices, software, and interfaces are created; and clinical, in which assistive technology is applied to a given end-user population. Moving from technology development towards clinical applications is a significant challenge. Developing performance metrics for assistive robots poses a related set of challenges. In this paper, we survey several areas of assistive robotic technology in order to derive and demonstrate domain-specific means for evaluating the performance of such systems. We also present two case studies of applied performance measures and a discussion regarding the ubiquity of functional performance measures across the sampled domains. Finally, we present guidelines for incorporating human performance metrics into end-user evaluations of assistive robotic technologies.

Influence of chemical composition on the X-ray photoemission, thermopower, specific heat, and magnetic properties of CeNi{sub 2}(Si{sub 1-y}Ge{sub y}){sub 2}

Energy Technology Data Exchange (ETDEWEB)

Tolinski, T.; Synoradzki, K. [Polish Academy of Sciences, Institute of Molecular Physics, Poznan (Poland); Bajorek, A.; Chelkowska, G. [Silesian University, Institute of Physics, Katowice (Poland); Koterlyn, M. [K. Wielkiego University, Institute of Physics, Bydgoszcz (Poland); Ivan Franko National University of L' viv, Faculty of Electronics, L' viv (Ukraine); Koterlyn, G. [National Academy of Sciences of Ukraine and Ministry of Education and Science of Ukraine, Western Scientific Center, L' viv (Ukraine); Yasnitskii, R. [Ivan Franko National University of L' viv, Faculty of Electronics, L' viv (Ukraine)

2017-06-15

We report our studies of the intermediate compositions between CeNi{sub 2}Si{sub 2} and CeNi{sub 2}Ge{sub 2}, i.e., the alloys CeNi{sub 2}(Si{sub 1-y}Ge{sub y}){sub 2} by means of the thermopower, electrical resistivity, specific heat, magnetic susceptibility, and X-ray photoemission measurements. CeNi{sub 2}Si{sub 2} is a fluctuating valence system and CeNi{sub 2}Ge{sub 2} is known to show the heavy fermion behaviour. The change of the temperature dependence of the resistivity towards the typical metallic behaviour occurs below y ∝ 0.25. The transition between CeNi{sub 2}Si{sub 2} and CeNi{sub 2}Ge{sub 2} is discussed in the frames of competition between the crystal electric field and Kondo interactions. It is found that valence stabilisation occurs for Ge content y > 0.25. The hybridization energy Δ determined from the XPS Ce 3d spectrum reflects well the behaviour of the parameter E{sub ex} obtained from the analysis of the magnetic susceptibility by the interconfiguration fluctuation model. It has been also shown that thermopower data can be successfully described employing the single ion model for 0.6 < y < 1.0 and two-band model including the crystal electric field splitting for y ≤ 0.25. (orig.)

32 CFR 239.15 - List of HAP field offices.

Science.gov (United States)

2010-07-01

... 32 National Defense 2 2010-07-01 2010-07-01 false List of HAP field offices. 239.15 Section 239.15...) MISCELLANEOUS HOMEOWNERS ASSISTANCE PROGRAM-APPLICATION PROCESSING § 239.15 List of HAP field offices. Homeowners Assistance Program field offices that process HAP applications for installations and applicants...

Disorder-driven metal-insulator-transition assisted by interband Coulomb repulsion in a surface transfer doped electron system

Science.gov (United States)

Francisco Sánchez-Royo, Juan

2012-12-01

The two-dimensional conducting properties of the Si(111) \\sqrt {3} \\times \\sqrt {3} surface doped by the charge surface transfer mechanism have been calculated in the frame of a semiclassical Drude-Boltzmann model considering donor scattering mechanisms. To perform these calculations, the required values of the carrier effective mass were extracted from reported angle-resolved photoemission results. The calculated doping dependence of the surface conductance reproduces experimental results reported and reveals an intricate metallization process driven by disorder and assisted by interband interactions. The system should behave as an insulator even at relatively low doping due to disorder. However, when doping increases, the system achieves to attenuate the inherent localization effects introduced by disorder and to conduct by percolation. The mechanism found by the system to conduct appears to be connected with the increasing of the carrier effective mass observed with doping, which seems to be caused by interband interactions involving the conducting band and deeper ones. This mass enhancement reduces the donor Bohr radius and, consequently, promotes the screening ability of the donor potential by the electron gas.

Photoemission study of the development of the Ti/GaAs(110) interface

International Nuclear Information System (INIS)

Ruckman, M.W.; del Giudice, M.; Joyce, J.J.; Weaver, J.H.

1986-01-01

Photoemission spectra of the Ga and As 3d core levels, the Ti 3p core levels, and the valence bands have been used to study the formation of the Ti/GaAs(110) interface. These results indicate that a multicomponent interfacial zone forms with reaction initiated at ultralow coverage and a rapid shift of E/sub F/ as the Schottky barrier forms (core-level shift 625 meV). After the onset of reaction, the Ga 3d core level shifts continuously to lower binding energy with increasing coverage (total shift of 1.66 eV by roughly-equal60 A Ti deposition). The As core-level profile indicates immediate reaction, the formation of two Ti: As bonding configurations at low coverage, and the appearance of another which persists to very high Ti coverage (> or =160 A) and is characteristic of a Ti-metal-rich environment. Core-level intensity profiles show preferential out-diffusion of As at every stage of interface formation. Core studies of the evolving Ti 3p emission show gradual convergence to bulk Ti as the overlayer becomes increasingly Ti rich. Likewise, valence-band studies reveal predominantly As-derived states below metal d states at E/sub F/. Comparison to previous results for Cr, V, Ce, and Sm overlayers on GaAs shows parallel trends in interface formation with differences related to the metal overlayer

Surface State Dynamics of Topological Insulators Investigated by Femtosecond Time- and Angle-Resolved Photoemission Spectroscopy

Directory of Open Access Journals (Sweden)

Hamoon Hedayat

2018-04-01

Full Text Available Topological insulators (TI are known for striking quantum phenomena associated with their spin-polarized topological surface state (TSS. The latter in particular forms a Dirac cone that bridges the energy gap between valence and conduction bands, providing a unique opportunity for prospective device applications. In TI of the BixSb2−xTeySe3−y (BSTS family, stoichiometry determines the morphology and position of the Dirac cone with respect to the Fermi level. In order to engineer specific transport properties, a careful tuning of the TSS is highly desired. Therefore, we have systematically explored BSTS samples with different stoichiometries by time- and angle-resolved photoemission spectroscopy (TARPES. This technique provides snapshots of the electronic structure and discloses the carrier dynamics in surface and bulk states, providing crucial information for the design of electro-spin current devices. Our results reveal the central role of doping level on the Dirac cone structure and its femtosecond dynamics. In particular, an extraordinarily long TSS lifetime is observed when the the vertex of the Dirac cone lies at the Fermi level.

The acetone bandpass detector for inverse photoemission: operation in proportional and Geiger–Müller modes

Science.gov (United States)

Thiede, Christian; Niehues, Iris; Schmidt, Anke B.; Donath, Markus

2018-06-01

Inverse photoemission is the most versatile experimental tool to study the unoccupied electronic structure at surfaces of solids. Typically, the experiments are performed in the isochromat mode with bandpass photon detectors. For gas-filled counters, the bandpass behavior is realized by the combination of the photoionization threshold of the counting gas as the high-pass filter and the ultraviolet transmission cutoff of an alkaline earth fluoride entrance window as the low-pass filter. The transmission characteristics of the entrance window determine the optical bandpass. The performance of the counter depends on the composition of the detection gas and the fill-gas pressure, the readout electronics and the counter geometry. For the well-known combination of acetone and CaF2, the detector can be operated in proportional and Geiger–Müller modes. In this work, we review aspects concerning the working principles, the counter construction and the read-out electronics. We identify optimum working parameters and provide a step-by-step recipe how to build, install and operate the device.

Crystal structure and X-ray photoemission spectroscopic study of A{sub 2}LaMO{sub 6} [A=Ba, Ca; M=Nb, Ta

Energy Technology Data Exchange (ETDEWEB)

Dutta, Alo, E-mail: alo_dutta@yahoo.com [Department of Condensed Matter Physics and Material Sciences, S. N. Bose National Centre for Basic Sciences, Block-JD, Sector-III, Salt Lake, Kolkata 700098 (India); Saha, Sujoy [Department of Physics, Bose Institute, 93/1 Acharya Prafulla Chandra Road, Kolkata 700009 (India); Kumari, Premlata [Department of Chemistry, Government P.G. College, Lansdowne, Pauri-Garhwal 246139 (India); Sinha, T.P. [Department of Physics, Bose Institute, 93/1 Acharya Prafulla Chandra Road, Kolkata 700009 (India); Shannigrahi, Santiranjan [Institute of Materials Research and Engineering, Agency for Science Technology and Research, 3 Research Link, Singapore 117602 (Singapore)

2015-09-15

The X-ray photoemission spectroscopic (XPS) study of the double perovskite oxides A{sub 2}LaMO{sub 6} [A=Ba, Ca; M=Nb, Ta] synthesized by the solid-state reaction technique has been carried out to investigate the nature of the chemical state of the constituent ions and the bonding between them. The Rietveld refinement of the X-ray diffraction patterns suggests the monoclinic crystal structure of all the materials at room temperature. The negative and positive chemical shifts of the core level XPS spectrum of O-1s and Nb-3d{sub 3/2}/Ta-4f{sub 5/2} respectively suggest the covalent bonding between Nb/Ta cations and O ion. The change of the bonding strength between the anion and the cations from one material to another has been analyzed. The vibrational property of the materials is investigated using the room temperature Raman spectra. A large covalency of Ta-based compound than Nb compound is confirmed from the relative shifting of the Raman modes of the materials. - Graphical abstract: Crystal structure of two perovskite oxides CLN and CLT is investigated. XPS study confirms the two different co-ordination environments of Ca and covalent bonding between B-site cations and O-ion. - Highlights: • Ordered perovskite structure obtained by Rietveld refinement of XRD patterns. • Study of nature of chemical bonding by X-ray photoemission spectroscopy. • Opposite chemical shift of d-states of Nb/Ta with respect to O. • Covalent bonding between d-states of Nb/Ta and O. • Relative Raman shifts of CLN and CLT substantiate the more covalent character of Ta than Nb.

Electronic properties of novel topological quantum materials studied by angle-resolved photoemission spectroscopy (ARPES)

Energy Technology Data Exchange (ETDEWEB)

Wu, Yun [Iowa State Univ., Ames, IA (United States)

2016-12-17

The discovery of quantum Hall e ect has motivated the use of topology instead of broken symmetry to classify the states of matter. Quantum spin Hall e ect has been proposed to have a separation of spin currents as an analogue of the charge currents separation in quantum Hall e ect, leading us to the era of topological insulators. Three-dimensional analogue of the Dirac state in graphene has brought us the three-dimensional Dirac states. Materials with three-dimensional Dirac states could potentially be the parent compounds for Weyl semimetals and topological insulators when time-reversal or space inversion symmetry is broken. In addition to the single Dirac point linking the two dispersion cones in the Dirac/Weyl semimetals, Dirac points can form a line in the momentum space, resulting in a topological node line semimetal. These fascinating novel topological quantum materials could provide us platforms for studying the relativistic physics in condensed matter systems and potentially lead to design of new electronic devices that run faster and consume less power than traditional, silicon based transistors. In this thesis, we present the electronic properties of novel topological quantum materials studied by angle-resolved photoemission spectroscopy (ARPES).

Synthesis and field emission properties of carbon nanotubes grown in ethanol flame based on a photoresist-assisted catalyst annealing process

International Nuclear Information System (INIS)

Yang Xiaoxia; Fang Guojia; Liu Nishuang; Wang Chong; Zheng Qiao; Zhou Hai; Zhao Dongshan; Long Hao; Liu Yuping; Zhao Xingzhong

2009-01-01

Carbon nanotubes (CNTs) have been grown directly on a Si substrate without a diffusion barrier in ethanol diffusion flame using Ni as the catalyst after a photoresist-assisted catalyst annealing process. The growth mechanism of as-synthesized CNTs is confirmed by scanning electron microscopy, high resolution transmission-electron microscopy and energy-dispersive spectroscopy. The photoresist is the key for the formation of active catalyst particles during annealing process, which then result in the growth of CNTs. The catalyst annealing temperature has been found to affect the morphologies and field electron emission properties of CNTs significantly. The field emission properties of as-grown CNTs are investigated with a diode structure and the obtained CNTs exhibit enhanced characteristics. This technique will be applicable to a low-cost fabrication process of electron-emitter arrays.

Correlation of CVD Diamond Electron Emission with Film Properties

Science.gov (United States)

Bozeman, S. P.; Baumann, P. K.; Ward, B. L.; Nemanich, R. J.; Dreifus, D. L.

1996-03-01

Electron field emission from metals is affected by surface morphology and the properties of any dielectric coating. Recent results have demonstrated low field electron emission from p-type diamond, and photoemission measurements have identified surface treatments that result in a negative electron affinity (NEA). In this study, the field emission from diamond is correlated with surface treatment, surface roughness, and film properties (doping and defects). Electron emission measurements are reported on diamond films synthesized by plasma CVD. Ultraviolet photoemission spectroscopy indicates that the CVD films exhibit a NEA after exposure to hydrogen plasma. Field emission current-voltage measurements indicate "threshold voltages" ranging from approximately 20 to 100 V/micron.

Robot-assisted urologic surgery in 2010 - Advancements and future outlook

Directory of Open Access Journals (Sweden)

Paurush Babbar

2011-01-01

Full Text Available Robotic surgery is a cutting edge and minimally invasive procedure, which has generated a great deal of excitement in the urologic community. While there has been much advancement in this emerging technology, it is safe to say that robotic urologic surgery holds tremendous potential for progress in the near future. Hence, it is paramount that urologists stay up-to-date regarding new developments in the realm of robotics with respect to novel applications, limitations and opportunities for incorporation into their practice. Robot-assisted surgery provides an enhanced 3D view, increased magnification of the surgical field, better manual dexterity, relatively bloodless field, elimination of surgeon′s tremor, reduction in a surgeon′s fatigue and mitigation of scattered light. All these factors translate into greater precision of surgical dissection, which is imperative in providing better intraoperative and postoperative outcomes. Pioneering work assessing the feasibility of robotic surgery in urology began in the early 2000′s with robot-assisted radical prostatectomy and has since expanded to procedures such as robot-assisted radical cystectomy, robot-assisted partial nephrectomy, robot-assisted nephroureterectomy and robot-assisted pyeloplasty. A MEDLINE search was used to identify recent articles (within the last two years and publications of specific importance, which highlighted the recent developments and future direction of robotics. This review will use the aforementioned urologic surgeries as vehicles to evaluate the current status and future role of robotics in the advancement of the field of urology.

Laser-assisted electron scattering in strong-field ionization of dense water vapor by ultrashort laser pulses

International Nuclear Information System (INIS)

Wilke, M; Al-Obaidi, R; Moguilevski, A; Kothe, A; Engel, N; Metje, J; Kiyan, I Yu; Aziz, E F

2014-01-01

We report on strong-field ionization of dense water gas in a short infrared laser pulse. By employing a unique combination of photoelectron spectroscopy with a liquid micro-jet technique, we observe how the character of electron emission at high kinetic energies changes with the increase of the medium density. This change is associated with the process of laser-assisted electron scattering (LAES) on neighboring particles, which becomes a dominant mechanism of hot electron emission at higher medium densities. The manifestation of this mechanism is found to require densities that are orders of magnitude lower than those considered for heating the laser-generated plasmas via the LAES process. The experimental results are supported by simulations of the LAES yield with the use of the Kroll–Watson theory. (paper)

Lending a helping hand: toward novel assistive robotic arms

NARCIS (Netherlands)

Groothuis, Stefan; Stramigioli, Stefano; Carloni, Raffaella

Assistive robotics is an increasingly popular research field, which has led to a large number of commercial and noncommercial systems aimed at assisting physically impaired or elderly users in the activities of daily living. In this article, we propose five criteria based on robotic arm usage

Pulsed electric fields

Science.gov (United States)

The concept of pulsed electric fields (PEF) was first proposed in 1967 to change the behavior or microorganisms. The electric field phenomenon was identified as membrane rupture theory in the 1980s. Increasing the membrane permeability led to the application of PEF assisted extraction of cellular co...

Transition from the adiabatic to the sudden limit in core-electron photoemission

Science.gov (United States)

Hedin, Lars; Michiels, John; Inglesfield, John

1998-12-01

Experimental results for core-electron photoemission Jk(ω) are often compared with the one-electron spectral function Ac(ɛk-ω), where ω is the photon energy, ɛk is the photoelectron energy, and the optical transition matrix elements are taken as constant. Since Jk(ω) is nonzero only for ɛk>0, we must actually compare it with Ac(ɛk-ω)θ(ɛk). For metals Ac(ω) is known to have a quasiparticle (QP) peak with an asymmetric power-law [theories of Mahan, Nozières, de Dominicis, Langreth, and others (MND)] singularity due to low-energy particle-hole excitations. The QP peak starts at the core-electron energy ɛc, and is followed by an extended satellite (shakeup) structure at smaller ω. For photon energies ω just above threshold, ωth=-ɛc, Ac(ɛk-ω)θ(ɛk) as a function of ɛk (ω constant) is cut just behind the quasiparticle peak, and neither the tail of the MND line nor the plasmon satellites are present. The sudden (high-energy) limit is given by a convolution of Ac(ω) and a loss function, i.e., by the Berglund-Spicer two-step expression. Thus Ac(ω) alone does not give the correct photoelectron spectrum, neither at low nor at high energies. We present an extension of the quantum-mechanical (QM) models developed earlier by Inglesfield, and by Bardyszewski and Hedin to calculate Jk(ω). It includes recoil and damping, as well as shakeup effects and extrinsic losses, is exact in the high-energy limit, and allows calculations of Jk(ω) including the MND line and multiple plasmon losses. The model, which involves electrons coupled to quasibosons, is motivated by detailed arguments. As an illustration we have made quantitative calculations for a semi-infinite jellium with the density of aluminum metal and an embedded atom. The coupling functions (fluctuation potentials) between the electron and the quasibosons are related to the random-phase-approximation dielectric function, and different levels of approximations are evaluated numerically. The differences

Cognitive assisted living ambient system: a survey

Directory of Open Access Journals (Sweden)

Ruijiao Li

2015-11-01

Full Text Available The demographic change towards an aging population is creating a significant impact and introducing drastic challenges to our society. We therefore need to find ways to assist older people to stay independently and prevent social isolation of these population. Information and Communication Technologies (ICT provide various solutions to help older adults to improve their quality of life, stay healthier, and live independently for a time. Ambient Assisted Living (AAL is a field to investigate innovative technologies to provide assistance as well as healthcare and rehabilitation to impaired seniors. The paper provides a review of research background and technologies of AAL.

The UHV Experimental Chamber For Optical Measurements (Reflectivity and Absorption) and Angle Resolved Photoemission of the BEAR Beamline at ELETTRA

International Nuclear Information System (INIS)

Pasquali, L.; Nannarone, S.; De Luisa, A.

2004-01-01

The experimental station of the BEAR (Bending magnet for Emission, Absorption and Reflectivity) beamline at ELETTRA (Trieste, Italy) is an UHV chamber conceived to fully exploit the spectroscopic possibilities offered by the light spot produced by the beamline. Spectroscopies include reflectivity (θ-2θ and diffuse), optical absorption, fluorescence and angle resolved photoemission. The chamber can be rotated around the beam axis to select the s (TE) or p (TM) incidence conditions and/or the position of the ellipse of polarization with respect to the sample. Photon detectors (e.g. photodiodes) and electron detector (hemispherical analyzer - 1 deg. angular resolution, 20 meV energy resolution) cover about completely the full 2π solid angle above the sample surface in any light incidence condition

Preschool teaching staff 's opinions on the importance of preschool curricular fields of activities, art genres and visual arts fields

OpenAIRE

Zupančič, Tomaž; Mulej, Matjaž; Čagran, Branka

2017-01-01

This article presents preschool teachers’ and assistant teachers’ opinions on the importance of selected fields of educational work in kindergartens. The article first highlights the importance of activities expressing artistic creativity within modern curriculums. Then, it presents an empirical study that examines the preschool teachers’ and assistant teachers’ opinions on the importance of the educational fields, art genres, and visual arts fields. In research hypotheses, we presumed that p...

Preschool Teaching Staff’s Opinions on the Importance of Preschool Curricular Fields of Activities, Art Genres and Visual Arts Fields

OpenAIRE

Tomaž Zupančič; Branka Čagran; Matjaž Mulej

2015-01-01

This article presents preschool teachers’ and assistant teachers’ opinions on the importance of selected fields of educational work in kindergartens. The article first highlights the importance of activities expressing artistic creativity within modern curriculums. Then, it presents an empirical study that examines the preschool teachers’ and assistant teachers’ opinions on the importance of the educational fields, art genres, and visual arts fields. In research hypotheses, we presumed that p...

Religious aspects of assisted reproduction

Science.gov (United States)

Sallam, H N; Sallam, N H

2016-03-28

Human response to new developments regarding birth, death, marriage and divorce is largely shaped by religious beliefs. When assisted reproduction was introduced into medical practice in the last quarter of the twentieth century, it was fiercely attacked by some religious groups and highly welcomed by others. Today, assisted reproduction is accepted in nearly all its forms by Judaism, Hinduism and Buddhism, although most Orthodox Jews refuse third party involvement. On the contrary assisted reproduction is totally unacceptable to Roman Catholicism, while Protestants, Anglicans, Coptic Christians and Sunni Muslims accept most of its forms, which do not involve gamete or embryo donation. Orthodox Christians are less strict than Catholic Christians but still refuse third party involvement. Interestingly, in contrast to Sunni Islam, Shi'a Islam accepts gamete donation and has made provisions to institutionalize it. Chinese culture is strongly influenced by Confucianism, which accepts all forms of assisted reproduction that do not involve third parties. Other communities follow the law of the land, which is usually dictated by the religious group(s) that make(s) the majority of that specific community. The debate will certainly continue as long as new developments arise in the ever-evolving field of assisted reproduction.

Active spectroscopic measurements of the bulk deuterium properties in the DIII-D tokamak (invited)

Energy Technology Data Exchange (ETDEWEB)

Grierson, B. A.; Pablant, N. A.; Solomon, W. M. [Princeton Plasma Physics Laboratory, Princeton, New Jersey 08543 (United States); Burrell, K. H.; Groebner, R. J.; Kaplan, D. H.; Van Zeeland, M. A. [General Atomics, P.O. Box 85608, San Diego, California 92186-5608 (United States); Chrystal, C. [University of California San Diego, La Jolla, California 92093 (United States); Heidbrink, W. W. [University of California Irvine, Irvine, California 92697 (United States); Munoz Burgos, J. M. [Oak Ridge Institute for Science Education, Oak Ridge, Tennessee 37831-0117 (United States)

2012-10-15

The neutral-beam induced D{sub {alpha}} emission spectrum contains a wealth of information such as deuterium ion temperature, toroidal rotation, density, beam emission intensity, beam neutral density, and local magnetic field strength magnitude Double-Vertical-Line B Double-Vertical-Line from the Stark-split beam emission spectrum, and fast-ion D{sub {alpha}} emission (FIDA) proportional to the beam-injected fast ion density. A comprehensive spectral fitting routine which accounts for all photoemission processes is employed for the spectral analysis. Interpretation of the measurements to determine physically relevant plasma parameters is assisted by the use of an optimized viewing geometry and forward modeling of the emission spectra using a Monte-Carlo 3D simulation code.

On the wide-energy-range tuning of x-ray photoemission electron microscope optics for the observation of the photoelectrons excited by several keV x-rays

International Nuclear Information System (INIS)

Yasufuku, H.; Yoshikawa, H.; Kimura, M.; Vlaicu, A.M.; Kato, M.; Kudo, M.; Fujikata, J.; Fukushima, S.

2006-01-01

We have newly developed an x-ray photoemission electron microscope (XPEEM) which uses both soft x-rays and hard x-rays at the undulator beam line BL15XU in the synchrotron radiation (SR) facility SPring-8 to observe various practical materials. In combination with an energy analyzer and high brilliant x-ray source, the detection of high kinetic energy inner-shell photoelectrons is essential for revealing the chemical properties of specimen subsurfaces or buried interfaces, owing to long inelastic mean free path of the high kinetic energy photoelectrons. The most significant result in our design is the new combined electric and magnetic field objective lens in which the magnetic field penetrates up to the sample surface. This allows the measurement with high spatial resolution of both low intensity images of inner-shell photoelectrons with high kinetic energy and high intensity images of secondary electrons. By using the sample bias scan method, we can easily change the focus condition of the objective lens in order to allow the energy filtered imaging with photoelectrons having the kinetic energy in a wide range (1-10 000 eV). By the combination of high brilliant SR x-rays, the new objective lens, and sample bias method, our XPEEM can successfully obtain the microarea x-ray photoelectron spectra and energy filtered XPEEM images of inner-shell photoelectrons, such as Si 1s, without any surface cleaning procedure. The energy filtered XPEEM image using photoelectrons from deep inner shells, Si 1s, was obtained for the first time

Employee Assistance Programs in Canada.

Science.gov (United States)

Jaffe, Peter; And Others

1988-01-01

Employee assistance programs (EAP) are evaluated in questionnaire responses from 73 of 109 (67 percent) Canadian school boards and 35 (50 percent) of the clients of the EAP in London, Ontario. Explores the nature of current programs and emerging trends in this field. (MLF)

Feasibility to apply the steam assisted gravity drainage (SAGD) technique in the country's heavy crude-oil fields

International Nuclear Information System (INIS)

Rodriguez, Edwin; Orjuela, Jaime

2004-01-01

The steam assisted gravity drainage (SAGD) processes are one of the most efficient and profitable technologies for the production of heavy crude oils and oil sands. These processes involve the drilling of a couple of parallel horizontal wells, separated by a vertical distance and located near the oil field base. The upper well is used to continuously inject steam into the zone of interest, while the lower well collects all resulting fluids (oil, condensate and formation water) and takes them to the surface (Butler, 1994). This technology has been successfully implemented in countries such as Canada, Venezuela and United States, reaching recovery factors in excess of 50%. This article provides an overview of the technique's operation mechanism and the process most relevant characteristics, as well as the various categories this technology is divided into, including all its advantages and limitations. Furthermore, the article sets the oil field's minimal conditions under which the SAGD process is efficient, which conditions, as integrated to a series of mathematical models, allow to make forecasts on production, thermal efficiency (ODR) and oil to be recovered, as long as it is feasible (from a technical point of view) to apply this technique to a defined oil field. The information and concepts compiled during this research prompted the development of software, which may be used as an information, analysis and interpretation tool to predict and quantify this technology's performance. Based on the article, preliminary studies were started for the country's heavy crude-oil fields, identifying which provide the minimum conditions for the successful development of a pilot project

Nanoscale Phase Separation and Lattice Complexity in VO2: The Metal–Insulator Transition Investigated by XANES via Auger Electron Yield at the Vanadium L23-Edge and Resonant Photoemission

Directory of Open Access Journals (Sweden)

Augusto Marcelli

2017-12-01

Full Text Available Among transition metal oxides, VO2 is a particularly interesting and challenging correlated electron material where an insulator to metal transition (MIT occurs near room temperature. Here we investigate a 16 nm thick strained vanadium dioxide film, trying to clarify the dynamic behavior of the insulator/metal transition. We measured (resonant photoemission below and above the MIT transition temperature, focusing on heating and cooling effects at the vanadium L23-edge using X-ray Absorption Near-Edge Structure (XANES. The vanadium L23-edges probe the transitions from the 2p core level to final unoccupied states with 3d orbital symmetry above the Fermi level. The dynamics of the 3d unoccupied states both at the L3- and at the L2-edge are in agreement with the hysteretic behavior of this thin film. In the first stage of the cooling, the 3d unoccupied states do not change while the transition in the insulating phase appears below 60 °C. Finally, Resonant Photoemission Spectra (ResPES point out a shift of the Fermi level of ~0.75 eV, which can be correlated to the dynamics of the 3d// orbitals, the electron–electron correlation, and the stability of the metallic state.