WorldWideScience

Sample records for ferrous metallurgy enterprises

  1. Development of structural diagram of automated dispatch control system for power consumption at non-ferrous metallurgy enterprises

    Science.gov (United States)

    Klyuev, R. V.; Bosikov, I. I.; Madaeva, M. Z.; A-V Turluev, R.

    2018-03-01

    The structural scheme of the automated control system of power consumption at the industrial enterprise is developed in the article. At the non-ferrous metallurgy enterprise, an energy inspection and a rank analysis of the electrical energy consumption of the main processing equipment were carried out. It is established that the enterprises of non-ferrous metallurgy are a complex process system consisting of a set of thousands of jointly functioning technological facilities. For the most effective estimation of power consumption of enterprises, it is reasonable to use the automated system of dispatching control of power consumption (ASDCPC). The paper presents the results of the development of the ASDCPC structural diagram that allows one to perform on-line control and management of the energy and process parameters of the main production units and the enterprise as a whole. As a result of the introduction of ASDCPC at the non-ferrous metallurgy enterprise, the consumed active power was reduced during the peak hours of the load by 20%, the specific electricity consumption - by 14%, the cost of the energy component in the cost of production of hard alloys - by 3%.

  2. Improving the effectiveness of heat use in ferrous metallurgy

    Energy Technology Data Exchange (ETDEWEB)

    Yegorichev, A P; Lisiyenko, V G; Rozin, S Ye; Shchelokov, Ya M

    1980-01-01

    Ferrous metallurgy of the USSR consumes about 10% of the total consumption of fuel in the country. The specific consumption of fuel in 100-150-T open-hearth furnaces in the scrap-process flucuate (in kilograms of conventional fuel/T of metal) from 199-206 to 244-249, in 450-T open-hearth furnaces with scrap-ore process from 108 to 135, in method furnaces with step-like beams from 70 to 123, in heating furnaces of low-grade machines ''250'' through 55.4 to 79, and on heating pits of bloomings from 32.5 to 55.3. In openhearth production, the percentage of outlays for fuel is 2.5-4.5%, in rolling 0.6-2% of the net cost of conversion. The overconsumption of fuel up to 5% will increase the net cost of conversion by 0.030.23%. In order to increase the effectiveness of conservation of fuel in ferrous metallurgy, a new method has been proposed for evaluating the energy intensity of the final product of ferrous metallurgy which makes it possible to determine comprehensive energy outlays for the manufactured product. A new system has been developed for stimulating the enterprises of ferrous metallurgy in the struggle for conservation and reduction in the specific consumption norms of fuel. It is based on the establishment of average-sector and progressive standards for single-type units of equal output.

  3. Estimation of snow pollution in the region of non-ferrous metallurgy enterprises by the neutron activation method

    International Nuclear Information System (INIS)

    Khatamov, Sh.; Khamidova, R.; Kist, A.A.

    1980-01-01

    Possibility of determination of more than 25 chemical elements in snow water selected in the region of non-ferrous metallurgy enterprises has been shown using the methods of neutron activation and γ-spectrometry of high resolution. Elements were determined from one sample by three-fold irradiation in the nuclear reactor depending on the half-life period and other nuclear activation parameters of the formed radioisotopes. The analysis of snow cover has revealed the character of pollution of surrounding medium and air basin by toxical elements

  4. State-of-the-art and main options to improve fuel-energy complex of ferrous metallurgy

    Energy Technology Data Exchange (ETDEWEB)

    Rozenblit, G I; Pashkov, V D; Romanov, G M

    1981-01-01

    In 1980, the State Institute for the Design and Planning Metallury (Gripromez), elaborated ''The main options of Fuel and energy resources conservation (FERG) in ferrous metallurgy of the USSR program of works for the period 1981-1985 and up to 1990''. The Gipromez technical committee recommended: 1) elaborating feasibility studies and reports, developing branch schemes and starting complexes to separate out FERC measures; 2) inclusion of the FERC measures at the starting complexes as the first stages of main projects construction; 3) that the Ministy of Ferrous Metallurgy of the USSR, general designers and enterprises reconsider the starting complexes of the projects constructed during the present five-year period and incorporate in them the urgent FERC actions on heat-utilizing facilities. Changing the steel smelting process structure through more extensive use of the converter process and installation of continuous blank casting allows achievement of considerable fuel conservation, some 4 m trf per year as compared with its consumption in the scheme of open-hearth furnace - blooming mill (slabbing mill). During the 11th five-year-plan period introduction of metallurgy plant. An installation with discharge of the converter gas without its afterburning and successive utilization as a fuel in the converter shop of the Novolipetsk is planned.

  5. The economic analysis of the evolution of Romanian ferrous metallurgy

    Directory of Open Access Journals (Sweden)

    I. Bostan

    2012-10-01

    Full Text Available The ferrous metallurgy represents a traditional occupation, being extremely important for the national economy. Romania has gone through all the stages foreseen for the restructuring of this industry in compliance with the provisions of the European Council’s Decision (1999/582/EC concerning the partnership for the EU adherence, which included a special chapter on ferrous metallurgy, the provisions of the Protocol no. 2 (ECSC, as well as with other significant normative acts subsequently enacted. Following the performed restructuring – privatizations, state allowances, liquidations, re-technologization – the activity of this sector has developed, still being under the potential of the Romanian metallurgic industry. Nowadays, the disadvantages relating to energy intensity and the increased need for imported raw materials are doubled by the difficulties generated by the global crisis.

  6. CURRENT STATE AND TENDENCIES OF DEVELOPMENT OF FERROUS METALLURGY IN THE EAEU COUNTRIES

    Directory of Open Access Journals (Sweden)

    N. P. Dragun

    2016-01-01

    Full Text Available The analysis of modern status and tendencies of development of ferrous metallurgy in the countries of the EAEU is described in the article. On the basis of the conducted analysis are revealed the identified systemic problems of metallurgy and the conclusions on possible ways of their solution using the potential of integration are given.

  7. [Factors of working environment and process on non-ferrous metallurgy enterprises in Bashkortostan Republic and workers' occupational health].

    Science.gov (United States)

    Bakirov, A B; Takaev, R M; Kondrova, N S; Shaĭkhlislamova, E R

    2011-01-01

    The authors studied factors of working environment and process on nonferrous metallurgy enterprises in Bashkortostan Republic and evaluated their influence on the workers' occupational health over 1997-2009, with consideration of occupation, sex, age, length of service, work conditions and characters. The article demonstrates that sanitary and hygienic characteristics of occupations connected with machinery operation are prone to increased integral evaluation of work conditions due to underestimation of actual hardiness and intensity of work.

  8. Energy conservation and efficiency in Giprokoks designs at Ukrainian ferrous-metallurgical enterprises

    Energy Technology Data Exchange (ETDEWEB)

    M.I. Fal' kov [Giprokoks, the State Institute for the Design of Coke-Industry Enterprises, Kharkov (Ukraine)

    2009-07-15

    Energy conditions at Ukrainian ferrous-metallurgical enterprises are analyzed. Measures to boost energy conservation and energy efficiency are proposed: specifically, the introduction of systems for dry slaking of coke; and steam-gas turbines that employ coke-oven gas or a mixture of gases produced at metallurgical enterprises. Such turbines may be built from Ukrainian components.

  9. Powder metallurgy ferrous synchronizer ring with brass-based friction layer; Tetsu-do niso shoketsu synchronize ring no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    Okajima, H; Yoshikawa, K; Miyajima, K; Sugiyama, M [Toyota Motor Corp., Aichi (Japan); Nakamura, M; Ito, M [Japan Powder Metallurgy Co. Ltd., Tokyo (Japan)

    1997-10-01

    Synchronizer rings for manual transmissions are generally made of brass or molybdenum coated brass. Powder metallurgy (PM) synchronizer ring was developed for the purpose of high performance and cost reduction. This synchronizer ring consists of the high strength PM ferrous ring that needs neither special densification nor heat treatment, and it has the brass-based friction layer. New joining technique was required because of that shape and two different materials. Powder of copper-phosphorus alloy are admixed with the friction material. While sintering, that melt and migrate to the interface. Then the friction layer and the ferrous ring are joined tightly. 7 refs., 9 figs., 6 tabs.

  10. [The organization of the comprehensive prevention of urolithiasis among ferrous metallurgy workers].

    Science.gov (United States)

    Egorova, A M

    2009-01-01

    The purpose of study is to evaluate the effectiveness of the set of preventive measures as applied to 321 workers of basic ferrous metallurgy specialties (steel makers, mill men, hot metal shearers). During the clinical examination all the workers were divided on three groups: the workers without any pathology (11.83%, the first group), the workers with metabolic disorders only without urolitiasis (64.81%, the second group) and the workers with urolitiasis diagnosis approved by ultrasonography (23.36%, the third group). The effectiveness of rehabilitation measures was evaluated during half a year (diet therapy, drinking regimen, medicinal plants treatment). After the course of preventive measures was applied the overall health condition of most workers ameliorated and the number of workers with urolitiasis development risk factors reliably decreased up to 6-12%.

  11. Problem concerning the use of secondary fuel energy systems in ferrous metallurgy

    Energy Technology Data Exchange (ETDEWEB)

    Shchelokov, Ia M

    1981-01-01

    Ferrous metallurgy makes available significant amount of secondary fuel energy resources: the possible output of secondary energy resources amounts to about 400 to 450 million gigajoules, the capacity of using secondary energy resources amount to 140 to 150 million gigajoules. Eighty percent of the general amount of the used secondary fuel energy resources is used in mills of open-hearth, rolling, and aneealing production. In the last twenty-five years and in connection with the change in the technological plans in the metallurgical industry, the specific output of secondary energy resources by branch decreased from 4.5 to 2.25 gigajoules per one ton of steel. The designs of mass produced boiler users does not correspond to the technical needs of the developing technology of smelting and annealing production. The Uralenergochermet together with the Ural branch of the F. Dzerzhinski All-Union Heat Engineering Institute, in 1970, introduced into use at the Orsko-Knalilov metallurgical plant, an impulse purification boiler user system. Note is made of the positive test of the operation of the Seversk pipe plant in respect to the dispersion and burning of the grease and fuel oil by products hydrated up to 30 to 40% by using the heat in the boiler users. In a number of Ural metallurgy plants, a 100% use of secondary energy resources in the course of the year was insured. Excellent results were obtained concerning the insurance of the stable operation of the system of the used thermal energy center at the Magnezit Satkin plant.

  12. Metallurgy - steel and non-ferrous metals

    International Nuclear Information System (INIS)

    Wusatowski, R.

    1999-01-01

    Several actual problems of metallurgy and processing of the chief metals and their alloys, especially of steel, copper, zinc and aluminium were discussed. The thought was given to the problems of: scientific, technical (also the energy consumption of production, the evolution of technology), organizational, economical, even political nature (influence of the state on the development of industry). (author)

  13. Promoting energy conservation in China's metallurgy industry

    International Nuclear Information System (INIS)

    Lin, Boqiang; Du, Zhili

    2017-01-01

    China is undergoing rapid industrialization and urbanization, with consequent dramatic increase in energy demand. Given energy scarcity, environmental pollution, energy security and energy cost constraints, energy conservation will be the major strategy in China's transition to a low-carbon economy. Since the metallurgy industry is a main sector of energy consumption, the efficiency of energy conservation in this industry will affect the future prospects of energy savings. This paper analyzes the energy conservation potential of China's metallurgy industry. First, seemingly unrelated regression method is applied to investigate the relationship between energy relative price, R&D input, enterprise ownership structure, enterprise scale and energy intensity of the metallurgy industry. Then, based on the SUR results, we use the scenario analysis method to predict energy consumption and savings potential in the industry in different scenarios. This paper provides references for China's government and metallurgy industry in formulating relevant energy conservation policies. - Highlights: • Seemingly unrelated regression method is applied to analyze the energy intensity of metallurgy industry. • We use the scenario analysis method to predict energy consuming and energy saving of Chinese metallurgy industry. • Provide references for China's government and metallurgy industry in formulating relevant energy conservation policies.

  14. Fast neutron activation analysis in metallurgy

    International Nuclear Information System (INIS)

    Sterlinski, S.

    1981-01-01

    Article discusses the usage of a 14 MeV neutron generator for producing fast neutrons of different energies and intensities. A complete instrumental set-up for the neutron activation analysis (NAA) is given. In metallurgy the device is mainly used in the determination of oxygen and silicon in steel and non-ferrous metal, including different alloys

  15. Guangxi non-ferrous metal industry speeding up its restructuring

    Institute of Scientific and Technical Information of China (English)

    2007-01-01

    <正>Non-ferrous metal industry in Guangxi takes an important position in China.However,the waste of resources is severe due to its simple industrial structure,small size of enterprises, sloppy technology,scattered layout,obstructed market and indiscriminate mining.Starting from last year,Guangxi began the project of building a world-influential non-ferrous metal

  16. [Atmospheric emission of PCDD/Fs from secondary aluminum metallurgy industry in the southwest area, China].

    Science.gov (United States)

    Lu, Yi; Zhang, Xiao-Ling; Guo, Zhi-Shun; Jian, Chuan; Zhu, Ming-Ji; Deng, Li; Sun, Jing; Zhang, Qin

    2014-01-01

    Five secondary aluminum metallurgy enterprises in the southwest area of China were measured for emissions of PCDD/Fs. The results indicated that the emission levels of PCDD/Fs (as TEQ) were 0.015-0.16 ng x m(-3), and the average was 0.093 ng x m(-3) from secondary aluminum metallurgy enterprises. Emission factors of PCDD/Fs (as TEQ) from the five secondary aluminum metallurgy enterprises varied between 0.041 and 4.68 microg x t(-1) aluminum, and the average was 2.01 microg x t(-1) aluminum; among them, PCDD/Fs emission factors from the crucible smelting furnace was the highest. Congener distribution of PCDD/F in stack gas from the five secondary aluminum metallurgies was very different from each other. Moreover, the R(PCDF/PCDD) was the lowest in the enterprise which was installed only with bag filters; the R(PCDF/PCDD) were 3.8-12.6 (the average, 7.7) in the others which were installed with water scrubbers. The results above indicated that the mechanism of PCDD/Fs formation was related to the types of exhaust gas treatment device. The results of this study can provide technical support for the formulation of PCDD/Fs emission standards and the best available techniques in the secondary aluminum metallurgy industry.

  17. ITRA 084 - a microprocessor controlled rapid analyzer in mining and metallurgy

    International Nuclear Information System (INIS)

    Kliem, V.; Kreher, M.; Boy, N.

    1986-01-01

    A new rapid analyzer of the ITRA series has been developed at the Freiberg Research Institute of Non-Ferrous Metals for single and multi-element analysis in mining and non-ferrous metallurgy. INTRA-08 represents an efficient microprocessor-controlled on-line X-ray fluorescence analyzer based on the main principles utilized with success hitherto in device engineering (isotope excitation, four-channel modification, balance filter method). A U880 single-chip microcomputer provides the central control of the device including the execution of an extensive program for the matrix correction. The efficiency of the analyzer is demonstrated taking measured values as a basis

  18. Мелихов А.А., Федун Е.В. Реструктуризация предприятий черной металлургии с помощью аутсорсинга промышленных газов

    OpenAIRE

    Мелихов, А. А.; Федун, К. В.

    2015-01-01

    Article is devoted to consideration of expediency of carrying out restructuring by outsourcing in modern difficult conditions of development of the domestic industrial enterprises. In article the concept of restructuring outsourcing and advantage of its using. Relevance of use of industrial outsourcing at the enterprises of ferrous metallurgy is proved. The result of carrying out restructuring in the form of increase of efficiency of activity and competitiveness of the enterprise is defined. ...

  19. Emission of PCDD/Fs and dioxin-like PCBs from metallurgy industries in S. Korea.

    Science.gov (United States)

    Yu, Byeong-Woon; Jin, Guang-Zhu; Moon, Young-Hoon; Kim, Min-Kwan; Kyoung, Jong-Dai; Chang, Yoon-Seok

    2006-01-01

    The metallurgy industry and municipal waste incinerators are considered the main sources of polychlorinated dibenzo-p-dioxin and dibenzofurans (PCDD/Fs) in many countries. This study investigated the emission factors and total emissions of PCDD/Fs and dioxin-like polychlorinated biphenyls (PCBs) emitted from metallurgy industries (including ferrous and nonferrous foundries) in Korea. The toxic equivalency (TEQ) emission factor of PCDD/Fs was the highest for secondary copper production, at 24451 ng I-TEQ/ton. The total estimated emissions of PCDD/Fs from these sources were 35.259 g I-TEQ/yr, comprising 0.088 g I-TEQ/yr from ferrous foundries, 31.713 g I-TEQ/yr from copper production, 1.716 g I-TEQ/yr from lead production, 0.111 g I-TEQ/yr from zinc production, and 1.631 g I-TEQ/yr from aluminum production. The total estimated annual amounts of dioxin-like PCBs emitted from these sources were 13.260 g WHO-TEQ/yr, comprising 0.014 g WHO-TEQ/yr from ferrous foundries, 12.675 g WHO-TEQ/yr from copper production, 0.170 g WHO-TEQ/yr from lead production, 0.017 g WHO-TEQ/yr from zinc production, and 0.384 g WHO-TEQ/yr from aluminum production. The highest emission factor was found for secondary copper smelting, at 9770 ng WHO-TEQ/ton.

  20. Metallurgical aspects of welding. Ferrous and nonferrous materials. 4. new rev. ed.; Die Metallurgie des Schweissens. Eisenwerkstoffe - nichteisenmetallische Werkstoffe

    Energy Technology Data Exchange (ETDEWEB)

    Schulze, Guenter

    2010-07-01

    This is the fourth edition of the standard work on welding metallurgy. The various problems of ferrous and nonferrous materials in the welding process are presented in great detail. In order to prevent corrosion of welded constructions, metallurgical properties and problems of all important technical materials are discussed, i.e. alloyed and unalloyed steels, cast iron materials, and the most relevant nonferrous materials. At the end of each chapter, the interested reader will find exercises for self-studies. Some of these can be solved using the material presented in the book while others are intended for deepening and further training. Easy examples (with solutions) are found all over the book; they are helpful because they provide information on underlying mechanisms and interdependences that are not obvious at first glance. The information was adapted to new EURO standards and international standards (up to March 2009) as far as these are relevant to Germany. New information is provided, e.g., on new steel standards (constructional steels according to DIN EN 10025), heat-treatable steels according to DIN EN 10025-6 and DIN EN 10083, high-alloy steels according to DIN EN 10088, and filler materials for steel welding according to DIN EN ISO 2560. The systematics of the ''law of cohabitation'' was applied to welding engineering for the first time here. (orig.) [German] Das in vierter Auflage erscheinende Buch widmet sich der Schweissmetallurgie mit ihren Besonderheiten. Die vielfaeltigen Probleme der Eisenwerkstoffe und der nichteisenmetallischen Werkstoffe bei ihrer schweisstechnischen Verarbeitung werden ausfuehrlich dargestellt. Um Korrosionsschaeden an geschweissten Konstruktionen vorzubeugen, wird die Metallurgie aller technisch bedeutsamen Werkstoffe, wie unlegierte und legierte Staehle, Eisen-Gusswerkstoffe, die wichtigsten NE-Metalle, ausfuehrlich besprochen. An den Kapitelenden findet der interessierte Leser Aufgaben, von denen ein

  1. Modernization of the Ural Metallurgy during the Great Patriotic War (1941–1945

    Directory of Open Access Journals (Sweden)

    Vladimir V. Zaparii

    2013-09-01

    Full Text Available The article characterizes the Ural industry modernization in war footing, shows the significance of evacuation of enterprises from the Western areas of the country to the region, reveals their role in the formation of a new metallurgical center of modern metallurgy in terms of human resources and manufacture. Innovations in metallurgy, the role of human factor in solving industrial restructuring problem are examined. Forms and methods of science use for the industrial modernization are considered. Solving of human resources problem is shown. The author touches upon the problem of metallurgical sector management in wartime. The role of people’s heroism in this difficult period of Russian history is discussed.

  2. Variations of 57Fe hyperfine parameters in medicaments containing ferrous fumarate and ferrous sulfate

    International Nuclear Information System (INIS)

    Oshtrakh, M. I.; Novikov, E. G.; Dubiel, S. M.; Semionkin, V. A.

    2010-01-01

    Several commercially available medicaments containing ferrous fumarate (FeC 4 H 2 O 4 ) and ferrous sulfate (FeSO 4 ), as a source of ferrous iron, were studied using a high velocity resolution Mössbauer spectroscopy. A comparison of the 57 Fe hyperfine parameters revealed small variations for the main components in both medicaments indicating some differences in the ferrous fumarates and ferrous sulfates. It was also found that all spectra contained additional minor components probably related to ferrous and ferric impurities or to partially modified main components.

  3. Production of a low young modulus titanium alloy by powder metallurgy

    Directory of Open Access Journals (Sweden)

    Dalcy Roberto dos Santos

    2005-12-01

    Full Text Available Titanium alloys have several advantages over ferrous and non-ferrous metallic materials, such as high strengthto-weight ratio and excellent corrosion resistance. A blended elemental titanium powder metallurgy process has been developed to offer low cost commercial products. The process employs hydride-dehydride (HDH powders as raw material. In this work, results of the Ti-35Nb alloy sintering are presented. This alloy due to its lower modulus of elasticity and high biocompatibility is a promising candidate for aerospace and medical use. Samples were produced by mixing of initial metallic powders followed by uniaxial and cold isostatic pressing with subsequent densification by isochronal sintering between 900 up to 1600 °C, in vacuum. Sintering behavior was studied by means of microscopy and density. Sintered samples were characterized for phase composition, microstructure and microhardness by X-ray diffraction, scanning electron microscopy and Vickers indentation, respectively. Samples sintered at high temperatures display a fine plate-like alpha structure and intergranular beta. A few remaining pores are still found and density above 90% for specimens sintered in temperatures over 1500 °C is reached.

  4. Variations of {sup 57}Fe hyperfine parameters in medicaments containing ferrous fumarate and ferrous sulfate

    Energy Technology Data Exchange (ETDEWEB)

    Oshtrakh, M. I., E-mail: oshtrakh@mail.utnet.ru; Novikov, E. G. [Ural Federal University (The former Ural State Technical University-UPI), Faculty of Physical Techniques and Devices for Quality Control (Russian Federation); Dubiel, S. M. [AGH University of Science and Technology, Faculty of Physics and Computer Science (Poland); Semionkin, V. A. [Ural Federal University (The former Ural State Technical University-UPI), Faculty of Physical Techniques and Devices for Quality Control (Russian Federation)

    2010-04-15

    Several commercially available medicaments containing ferrous fumarate (FeC{sub 4}H{sub 2}O{sub 4}) and ferrous sulfate (FeSO{sub 4}), as a source of ferrous iron, were studied using a high velocity resolution Moessbauer spectroscopy. A comparison of the {sup 57}Fe hyperfine parameters revealed small variations for the main components in both medicaments indicating some differences in the ferrous fumarates and ferrous sulfates. It was also found that all spectra contained additional minor components probably related to ferrous and ferric impurities or to partially modified main components.

  5. RESEARCH ON INVESTMENT APPEAL AND COMPETITIVE CAPACITY OF INDUSTRIAL ENTERPRISES OF UKRAINE

    Directory of Open Access Journals (Sweden)

    Olena Khadzhynova

    2017-12-01

    Full Text Available The purpose of the research is an elaboration of theoretical, methodological, and methodical approaches to forming and developing competitive capacity and investment appeal of steel industry enterprises. The achievement of the given purpose has led to the necessity of formulating such scientific research concept, which bottom line is in the relevance of using modern management methods implemented in foreign manufacturing practices. These are innovative economic, technical, organizational, and corporate methods of managing enterprises with the help of developed systems of managing strategic changes in enterprise activities, the steel industry in particular, which will contribute to achieving the high level of effectiveness and competitiveness of domestic business units. The research methodology is based on the combination of theories of managing economic systems in the globalized market economy. The empirical base for the research consists of the works by domestic and foreign scientists on problems of formation and development of strategic change management systems at industrial enterprises, statistical records, companies’ public records in the Internet, data of international information agencies, Ukrainian legislation on regulating economic activity of enterprises. In carrying out the research, such methods were used as: general academic analysis and synthesis, systemic generalization, statistic and correlation analysis (when justifying the directions of development before carrying out the economic analysis of activities of metallurgical enterprises. There is a conclusion that the industry is concentrated and, consequently, long-term trends are quite predictable, but they require additional clarifications, taking into consideration the uncertainty in the modern state of world economy. It is determined that metallurgy development depends on GBP. The analysis shows that the countries with the high GDP level have quite developed metallurgy. One

  6. RECYCLING OF FERROUS METAL SHAVINGS

    Directory of Open Access Journals (Sweden)

    S. L. Rovin

    2017-01-01

    Full Text Available The most advanced and universal way of chips recycling of ferrous metals is the technology of direct chips remelting in rotational tilting furnaces (RBF directly at the enterprises-sources of waste generation. However common practice of iron and steel chips recycling is based on its briquetting and subsequent remelting in traditional furnaces.For cost reduction when chip briquetting and organization of hot briquetting sections in places of its formation highly efficient equipment – rotational dryer and RBF is proposed. The possibility and effectiveness of developed furnaces for lowand high-temperature chip heating in briquetting lines is proved. Thermal efficiency of such furnaces when dispersed materials heating is much higher than drum or feed-through furnaces. Hot briquetting of shavings reduces the pressing force, which reduces the specific energy consumption. The use of rotary kilns can reduce technological operations and equipment of production sites for the manufacture of briquettes

  7. Physical metallurgy. Vol. 6. Corrosion, oxidation and physical metallurgy applications

    International Nuclear Information System (INIS)

    Adda, Y.; Dupuy, J.M.; Philibert, J.; Quere, Y.

    1982-12-01

    This document deals with the following subjects: oxidation, corrosion and surface treatments. Some physical metallurgy applications are presented: aluminium alloys, high elastic limit materials, materials for very high temperature, nuclear metallurgy problems, composite materials, magnetic materials, very high purity materials, and, superconductor materials [fr

  8. Ferrous alloy metallurgy, liquid lithium corrosion and welding. Final report, April 1, 1973-March 31, 1984

    International Nuclear Information System (INIS)

    Olson, D.L.; Matlock, D.K.

    1984-01-01

    This research program consists of two parts: an evaluation of the corrosion behavior of ferrous alloys in liquid lithium, and a study of microstructure development and properties of dissimilar metal weldments. A ten-year overview of the research accomplishments made is presented. The effects of liquid lithium on both uniform corrosion and grain boundary penetration in ferrous alloys has been investigated as a function of time, temperature, base metal alloy content, and liquid lithium nitrogen content. Kinetic equations for the various corrosion processes have been developed and analyzed with respect to models for corrosion and corrosion product development. The effects of liquid lithium on mechanical properties, particularly fatigue, have been studied. Results have shown that in both austenitic stainless steels and ferritic steels, liquid lithium significantly reduces the mechanical integrity of all materials by inducing liquid metal embrittlement. A model for liquid metal embrittlement induced damage during fatigue was developed and shown to correlate with the experimental results. Microstructural development in austenitic weld metal, with particular emphasis on new grades with reduced chromium contents, has been investigated. The microstructures have been correlated with alloy content and the basics of a thermodynamic model for predicting weld metal microstructure has been developed. The high temperature mechanical behavior of dissimilar metal weldments (austenitic stainless steel to ferritic steel) has been investigated with the impression-creep test technique. Observed microstructural changes with position across the weldment are shown to correlate directly with creep behavior. A model based on deformation of composite materials was developed

  9. New evidence for prehistoric copper metallurgy in the vicinity of Bor

    Directory of Open Access Journals (Sweden)

    Kapuran Aleksandar

    2016-01-01

    Full Text Available The last three years of archaeological investigations at the site Ru`ana in Banjsko Polje, in the immediate vicinity of Bor, have provided new evidence regarding the role of non-ferrous metallurgy in the economy of the prehistoric communities of north-eastern Serbia. The remains of metallurgical furnaces and a large amount of metallic slags at two neighbouring sites in the mentioned settlement reveal that locations with many installations for the thermal processing of copper ore existed in the Bronze Age. We believe, judging by the finds of material culture, that metallurgical activities in this area also continued into the Iron Age and, possibly, into the 4th century AD. [Projekat Ministarstva nauke Republike Srbije, br. 177020: Archaeology of Serbia: Cultural identity, integration factors, technological processes and the role of the central Balkans in the development of European prehistory

  10. Current programmes of Metallurgy Division (1991)

    International Nuclear Information System (INIS)

    1991-01-01

    Current research and development programmes of the Metallurgy Division are listed under the headings: 1)Thrust Areas, 2)High Temperature Materials Section, 3)Chemical Metallurgy Section, 4)Metallurgical Thermochemistry Section, 5)Physical Metallurgy Section, 6)Mechanical Metallurgy Section, 7)Corrosion Metallurgy Section, 8)Electrochemical Science and Technology Section, 9)Ceramics Section, and 10)Fabrication and Maintenance Group. A list of equipment in the Division and a list of sciientific personnel of the Division are also given. (M.G.B.)

  11. Leben heisst ein Kämpfer sein : zum Verhältnis von Wissenschaft und Öffentlichkeit am Beispiel der modernen Eisenhüttenkunde and der Technischen Hochschule Aachen

    NARCIS (Netherlands)

    Krebs, S.

    2007-01-01

    To Live is to be Fighter - On the Relatioship of Science and Public Illustrated by the Example of Modern Ferrous Metallurgy at the Technical University Aachen. - The contribution pursues the question of how Fritz Wüst, professor of ferrous metallurgy at the Technische Hochschule Aachen (1901-1921),

  12. Sinterability and microstructure evolution during sintering of ferrous powder mixtures

    Directory of Open Access Journals (Sweden)

    Kétner Bendo Demétrio

    2013-01-01

    Full Text Available The present work is focused on ferrous powder metallurgy and presents some results of a development of a suitable masteralloy for use as an additive to iron powder for the production of sintered steels. The masteralloy was produced by melting a powder mixture containing approximately Fe + 20% Ni + 20% Mn + 20% Si + 1% C (wt%, in order to obtain a cast billet that was converted into fine powder by crushing and milling. It was observed presence of SiC in the masteralloy after melting that is undesirable in the alloy. Si element should be introduced by using ferrosilicon. Sintered alloys with distinct contents of alloying elements were prepared by mixing the masteralloy powder to plain iron powder. Samples were produced by die compaction of the powder mixtures and sintering at 1200 °C in a differential dilatometer in order to record their linear dimensional behaviour during heating up and isothermal sintering, aiming at studying the sinterability of the compacts. Microstructure development during sintering was studied by SEM, XRD and microprobe analyses.

  13. Neutron radiography in metallurgy

    International Nuclear Information System (INIS)

    Rant, J.; Ilic, R.

    1977-01-01

    The review surveys microneutronographic and neutron-induced autoradiographic techniques and their applications in metallurgy. A brief survey of applications of neutron radiography as a method of non-destructive testing to some macroscopic problems in metallurgy is included. (author)

  14. NON-FERROUS EXPORTS CONCENTRATION AND GLOBAL INVESTMENTS

    Directory of Open Access Journals (Sweden)

    Brîndușa COVACI

    2016-12-01

    Full Text Available In the context of high-tech and telecommunication, non-ferrous sector has a crucial role in industries development. Cooper, nickel, aluminum, zinc, lead and tin are used, directly or indirectly, in most of the technologies, especially in high-tech production. The paper present a short index of the global investments for the non-ferrous transnational corporations listed on London Metal Exchange. The non-ferrous investment index presented in the paper refers to the most profitable corporation exports on world, European Union (EU28 and Central and Eastern Europe (CEE level. The export concentration, estimated through Herfindahl-Hirschmann index on world, EU28, CEE and Romanian level, show that the non-ferrous industry is in full process of releasing. The cases presented in the article show that the non-ferrous companies invest intensively in equipment and technologies with superior production capacities, which combat pollution given by non-ferrous processes, research and development for the non-ferrous innovative technologies, and creating new markets. Sustainable and intelligent development is the inflexion point of the non-ferrous transnational corporation investments. The research is predominant in exploration of the transnational corporations’ internet pages and reports, and statistical calculus from international trade websites.

  15. Metallography of powder metallurgy materials

    International Nuclear Information System (INIS)

    Lawley, Alan; Murphy, Thomas F.

    2003-01-01

    The primary distinction between the microstructure of an ingot metallurgy/wrought material and one fabricated by the powder metallurgy route of pressing followed by sintering is the presence of porosity in the latter. In its various morphologies, porosity affects the mechanical, physical, chemical, electrical and thermal properties of the material. Thus, it is important to be able to characterize quantitatively the microstructure of powder metallurgy parts and components. Metallographic procedures necessary for the reliable characterization of microstructures in powder metallurgy materials are reviewed, with emphasis on the intrinsic challenges presented by the presence of porosity. To illustrate the utility of these techniques, five case studies are presented involving powder metallurgy materials. These case studies demonstrate problem solving via metallography in diverse situations: failure of a tungsten carbide-coated precipitation hardening stainless steel, failure of a steel pump gear, quantification of the degree of sinter (DOS), simulation of performance of a porous filter using automated image analysis, and analysis of failure in a sinter brazed part assembly

  16. Problems of accounting, cost concerns and economic analysis in the mining enrichment industry

    Energy Technology Data Exchange (ETDEWEB)

    Slabinskiy, V T

    1980-01-01

    Mining enrichment enterprises of the ferrous and nonferrous metallurgy, coal and chemical industry have much in common in the area of technology of production, technical base, organization of labor and production. This in turn presupposes the possible development of a common procedure of accounting of expenditures for production, calculation of net cost of output and analysis of production-economic activity of enterprises. Based on scientific research and generalization of advanced experience of practical workers, means of improvement of economic operation in mining enrichment enterprises are outlined according to increasing demands of production control. An outline of analytic accounting of expenditures which provides for multitarget use of information has been developed: for organization of operational control of the formulation of net cost of output, determination of the results of self support activities of structural subdivisions of an enterprise, computation of the efficiency of scientific and technical progress. Experience of use of economic and mathematical methods in computers for this purpose is discussed.

  17. Emission profiles of polychlorinated dibenzodioxins, polychlorinated dibenzofurans (PCDD/Fs), dioxin-like PCBs and hexachlorobenzene (HCB) from secondary metallurgy industries in Portugal.

    Science.gov (United States)

    Antunes, Pedro; Viana, Paula; Vinhas, Tereza; Rivera, J; Gaspar, Elvira M S M

    2012-09-01

    This paper reports, for the first time, a study of dioxin emissions from 10 siderurgies and metallurgies, secondary copper, aluminum and lead metallurgies, in Portugal. The study reports the emission factors and total emission amounts of PCDD/Fs, dioxin-like PCBs and hexachlorobenzene (HCB). The congener patterns were characterized and are discussed. The results showed that the total amount of PCDFs is higher than PCDDs in flue gas of each industrial unit. The toxic equivalent emission factors of pollutants emitted are 3098-3338 ngI-TEQt(-1) for PCDD/Fs and 597-659 ng I-TEQt(-1) for dioxin-like PCBs in siderurgies production (total estimated emission amounts released to atmosphere of 3.9-4.5 g I-TEQyr(-1)), 50-152 ng I-TEQt(-1) for PCDD/Fs and 24-121 ng I-TEQt(-1) for dioxin-like PCBs in ferrous foundries production (total estimated emission amounts released to atmosphere of 0.0010-0.0016 g I-TEQyr(-1)) and 5.8-5715 ng I-TEQt(-1) for PCDD/Fs and 0.49-259 ng I-TEQt(-1) for dioxin-like PCBs in non-ferrous foundries production (total estimated emission amounts released to atmosphere of 0.00014-0.12 g I-TEQyr(-1)). The HCB emission from siderurgies production is 0.94-3.2 mg t(-1) (total estimated emission amounts released 0.94-3.8 g yr(-1)), being much smaller, residual, in the emissions of the other types of plants (0.0012-0.026 mg t(-1) production and total estimated emission amounts released to atmosphere of 0.013-1.7 mg yr(-1)). Copyright © 2012 Elsevier Ltd. All rights reserved.

  18. Fast and effective analysis of ferrous and non-ferrous alloys by X-ray fluorescence

    International Nuclear Information System (INIS)

    Gomez Serra, Abelardo

    1987-01-01

    An empirical method for the integral analysis of any kind of alloys, ferrous and non-ferrous, is described. The method is based on the intensities relation of the mixed elements and is independent of the size, shape and presentation of the sample. By this procedure, alloys with iron, copper, aluminium or magnesium base can be fastly classified. (S.M.) [es

  19. Superconductors by powder metallurgy techniques

    International Nuclear Information System (INIS)

    Pickus, M.R.; Wang, J.L.F.

    1976-05-01

    Fabrication methods for Nb 3 Sn type compounds are described. Information is included on the Bell Telephone process, the General Electric tape process, superconductor stability, the bronze process, powder metallurgy multifilamentary tapes and wires, and current assessment of powder metallurgy superconducting wire

  20. Metallurgi for Ingeniører

    DEFF Research Database (Denmark)

    Pedersen, Jan

    Ny gennemarbejdet udgave af den klassiske "Metallurgi for Ingeniører", først skrevet af K. Offer Andersen i 1962......Ny gennemarbejdet udgave af den klassiske "Metallurgi for Ingeniører", først skrevet af K. Offer Andersen i 1962...

  1. Development and prospect of china uranium mining and metallurgy

    International Nuclear Information System (INIS)

    Que Weimin; Wang Haifeng; Niu Yuqing; Gu Wancheng; Zhang Feifeng

    2007-01-01

    The development of industry of uranium mining and metallurgy in China has been reviewed generally, emphasizing on investigation approaches and application levels of uranium mining technologies such as in-situ leaching, heap leaching, stope leaching: on the basis of analysis on status of uranium mining and metallurgy and problems existed, also considering the specific features of deposit resources, the development orientation of uranium mining and metallurgy in China is pointed out. The industry of China uranium mining and metallurgy is faced to new opportunity of development and challenge in 21st century, the only way to realize sustainable development of uranium mining and metallurgy and harmonious development between economy and environment is to develop new technology on mining, ore beneficiation and metallurgy, increase the utilization level of uranium resources, low down impact on environment caused by mining and metallurgy. (authors)

  2. [Evaluation and prognosis of occupational risk in workers of nonferrous metallurgy enterprises].

    Science.gov (United States)

    Shliapnikov, D M; Kostarev, V G

    2014-01-01

    The article deals with results of a priori and a posteriori evaluation of occupational risk for workers' health. Categories of a priori occupational risk for workers are estimated as high to very high (intolerable) risk. Findings are that work conditions in nonferrous metallurgy workshop result in upper respiratory tract diseases (medium degree of occupational conditionality). Increased prevalence of such diseases among the workers is connected with length of service. The authors revealed priority factors for occupationally conditioned diseases. A promising approach in occupational medicine is creation of methods to evaluate and forecast occupational risk, that enable to specify goal parameters for prophylactic measures. For example, modelling the risk of occupationally conditioned diseases via changes in exposure to occupational factor and length of service proved that decrease of chemical concentrations in air of workplace to maximally allowable ones lowers risk of respiratory diseases from 14 to 6 cases per year, for length of service of 5 years and population risk.

  3. Fundamentals of powder metallurgy

    International Nuclear Information System (INIS)

    Khan, I.H.; Qureshi, K.A.; Minhas, J.I.

    1988-01-01

    This book is being presented to introduce the fundamentals of technology of powder metallurgy. An attempt has been made to present an overall view of powder metallurgy technology in the first chapter, whereas chapter 2 to 8 deal with the production of metal powders. The basic commercial methods of powder production are briefly described with illustrations. Chapter 9 to 12 describes briefly metal powder characteristics and principles of testing, mixing, blending, conditioning, compaction and sintering. (orig./A.B.)

  4. Powder metallurgy techniques in nuclear technology

    International Nuclear Information System (INIS)

    Mardon, P.G.

    1983-01-01

    The nuclear application of conventional powder metallurgy routes is centred on the fabrication of ceramic fuels. The stringent demands in terms of product performance required by the nuclear industry militate against the use of conventional powder metallurgy to produce metallic components such as the fuel cladding. However, the techniques developed in powder metallurgy find widespread application throughout nuclear technology. Illustrations of the use of these techniques are given in the fields of absorber materials, ceramic cladding materials, oxide fuels, cermet fuels, and the disposal of highly active waste. (author)

  5. Progress report of the Metallurgy Group

    International Nuclear Information System (INIS)

    Sundaram, C.V.; Moorthy, V.K.

    1975-01-01

    The activities of the Metallurgy Division of the Bhabha Atomic Research Centre, Bombay, during the year 1974 are reported under six sections, namely: ore dressing; extractive metallurgy; ceramics; physical metallurgy; corrosion and electrometallurgy, and radiometallurgy. The developmental programme is not only concerned with materials of nuclear interest such as uranium, thorium, plutonium, zirconium, niobium and beryllium, but also other materials of national interest such as titanium, tantalum, ceramics, corrosion-resistant alloys etc. In addition to the laboratory studies, collaborative work has also been undertaken with other units of the Department of Atomic Energy. (A.K.)

  6. Role of forgings in powder metallurgy industry

    International Nuclear Information System (INIS)

    Hayes, A.F.; DeRidder, A.J.

    1975-01-01

    Forging of powder metallurgy materials is discussed. Information and data are included on forging powder metallurgy W, Mo, In 100, Rene 95, Astroloy, Be, and Ti. It is noted that the combination of powder metallurgy and forging work provides the best product from standpoints of reproducibility, freedom from segregation, low scrap rate, and uniform mechanical properties. Experience is being used to develop contour forging from hot isostatic pressed billets or preforms. The quality of this product is under evaluation. Results show steady improvement and it is anticipated that continued effort will soon produce a reliable, less costly product. Forging can continue to be relied upon to correct subtle defects present in powder metallurgy material

  7. Ferrous Sulfate (Iron)

    Science.gov (United States)

    ... are allergic to ferrous sulfate, any other medications tartrazine (a yellow dye in some processed foods and ... in, tightly closed, and out of reach of children. Store it at room temperature and away from ...

  8. Functional dependency between the logistics security system and the MySAP ERP in metallurgy

    Directory of Open Access Journals (Sweden)

    P. Ranitović

    2013-10-01

    Full Text Available MySAP ERP - Enterprise Resource Planning (system - solution which provides a whole set of functions for the business analytics, finance, human resources management, logistics and corporate services has developed from SAP R/3. It is one of the main products of the SAP AG German multinational company and as such, it is a very important element of the international industrial and technological security system. By defining the functional dependency between the security systems (logistics security systems and the IT (My SAP ERP systems in metallurgy, a concept for designing MY SAP ERP system in metallurgic industry is defined, based on the security aspects.

  9. Bio technologies in extractive metallurgy

    International Nuclear Information System (INIS)

    Morin, D.

    1995-01-01

    The bio technologies processes used (or used in the future) in extractive metallurgy are presented. The most advanced one is the degradation of the metals sulfides (bacteria catalyzing the sulfides oxidation of Au, Cu, U). Two other applications outside the extractive metallurgy are also described: metals fixation by living or dead organic matter and the biological destruction of organic reactants such as cyanides. (A.B.)

  10. Metallurgy Department

    DEFF Research Database (Denmark)

    Risø National Laboratory, Roskilde

    The activities of the Metallurgy Department at Risø during 1981 are described. The work is presented in three chapters: General Materials Research, Technology and Materials Development, Fuel Elements. Furthermore, a survey is given of the department's participation in international collaboration...

  11. Basic metallurgy for nondestructive testing

    International Nuclear Information System (INIS)

    Abdul Nassir Ibrahim; Azali Muhammad; Ab. Razak Hamzah; Abd. Aziz Mohamed; Mohamad Pauzi Ismail

    2008-01-01

    For this chapter, reader will be served with the basic knowledge on metallurgy for nondestructive testing. One the main application of nondestructive testing is to detect discontinuity of mass defect in metal. As we already know, metal are widely used in many application such as in building as a system, component and engineering product. Steel and iron are metal that usually used in industry, especially heavy industry such as gas and petroleum industry, chemistry, electric generation, automobile, and military device. Based on this, basic knowledge on metallurgy must need by NDT practitioner. The combination between metallurgy and datas from radiography testing can make radiographer good interpretation on quality of the metal inspected and can used to make a good decision either to accept or not certain product, system or components.

  12. Biennial activity report of metallurgy programme for 1987 and 1988

    International Nuclear Information System (INIS)

    Shanmugam, V.; Rao, B.P.C.; Bhanu Sankara Rao, K.; Muralidharan, P.; Bhaduri, A.K.; Kuppusami, P.; Shyamsunder, M.T.; Sampath, N.; Sreedharan, O.M.

    1990-01-01

    The research and development (R and D) activities in the field of metallurgy at Indira Gandhi Centre for Atomic Research, Kalpakkam during 1987-1988 are reported in the form of individual summaries arranged under headings : (1) Mechanical Metallurgy Section, (2) Physical Metallurgy Section, (3) Chemical Metallurgy Section, (4) Materials Technology Section, (5) Division for PIE and NDT Development and (6) Quality Engineering Section. A list of publications by the staff scientists working in the field of metallurgy during report period is given in one of the appendices. (author). figs., tabs

  13. Technetium behavior in sulfide and ferrous iron solutions

    International Nuclear Information System (INIS)

    Lee, S.Y.; Bondietti, E.A.

    1982-01-01

    Pertechnetate oxyanion ( 99 TcO 4- ), a potentially mobile species in leachate from a breached radioactive waste repository, was removed from a brine solution by precipitation with sulfide, iron, and ferrous sulfide at environmental pH's. Maghemite (ν-Fe 2 O 3 ) and geothite (α-FeOOH) were the dominant minerals in the precipitate obtained from the TcO 4- -ferrous iron reaction. The observation of small particle size and poor crystallinity of the minerals formed in the presence of Tc suggested that the Tc was incorporated into the mineral structure after reduction to a lower valence state. Amorphous ferrous sulfide, an initial phase precipitating in the TcO 4- -ferrous iron-sulfide reaction, was transformed to goethite and hematite (α-Fe 2 O 3 ) on aging. The black precipitate obtained from the TcO 4- -sulfide reaction was poorly crystallized technetium sulfide (Tc 2 S 7 ) which was insoluble in both acid and alkaline solution in the absence of strong oxidents. The results suggested that ferrous- and/or sulfide-bearing groundwaters and minerals in host rocks or backfill barriers could reduce the mobility of Tc through the formation of less-soluble Tc-bearing iron and/or sulfide minerals

  14. Ferrous Metal Processing Plants

    Data.gov (United States)

    Department of Homeland Security — This map layer includes ferrous metal processing plants in the United States. The data represent commodities covered by the Minerals Information Team (MIT) of the...

  15. European Metals Conference

    CERN Document Server

    Vereecken, Jean

    1991-01-01

    This volume contains the papers that will be presented at 'EMC '91 '-the European Metals Conference-to be held in Brussels, Belgium, from 15 to 20 September 1991, and organized by Benelux Metallurgie, GDMB (Gesellschaft Deutscher Metallhutten­ und Bergleute) and IMM (the Institution of Mining and Metallurgy). 'EMC '91' is the first of an intended major series organized at the European level with the aim of bringing together all those who are involved with the extraction and processing of non-ferrous metals-European metallurgists and their international colleagues-to provide them with the opportunity to exchange views on the state and evolution of their industry. The programme covers all the different aspects of the metallurgy of non-ferrous metals from mining to fabricated products. Particular attention is being paid to the European non -ferrous industry with respect to changes in demand, the technology used, pressures on the environment and the competitive position of manufacturers. The contributions of the...

  16. Analysis of environment state in technogenic region and its threat to public health

    Directory of Open Access Journals (Sweden)

    Grishenko S.V.

    2014-03-01

    Full Text Available The purpose of the research is to give a complex hygienic evaluation of environment state in Donetsk region and to determine the degree of their potential danger to population health. It includes air pollution, water contamination, state of soil. Nearly 43000 samples of air, 32000 drinking water samples and 4500 soil samples were analyzed. Regions with the highest rate of environmental pollution were defined. It was found that the main sources of environment pollution in Donetsk region are ferrous and nonferrous metallurgy enterprises, power, coal, building industry and transport. All other sources ac¬count for only 5-10% of total emissions. Level of harmful technogenic pressing on population’s health was determined.

  17. 40 CFR 464.30 - Applicability; description of the ferrous casting subcategory.

    Science.gov (United States)

    2010-07-01

    ... ferrous casting subcategory. 464.30 Section 464.30 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS METAL MOLDING AND CASTING POINT SOURCE CATEGORY Ferrous Casting Subcategory § 464.30 Applicability; description of the ferrous casting subcategory. The...

  18. Proceedings of papers. 3. Balkan Metallurgical Conference; Kniga na trudovi. 3-ta Balkanska konferencija na metalurzite

    Energy Technology Data Exchange (ETDEWEB)

    Mickovski, Jovan [Faculty of Technology and Metallurgy, St. ' Cyril and Methodius' University, Skopje (Macedonia, The Former Yugoslav Republic of)

    2003-07-01

    This Conference aims to be a central event in the metallurgy research of Balkan, fulfilling the goals to present the most outstanding relevant developments in modern metallurgy; to inspire high standards of excellence in pure and applied metallurgy research; to attract outstanding scientists to present central lectures on modem metallurgical research, and on the challenges imposed by the needs of society; to inspire the young generation of metallurgists in Balkan and other countries. Following these lines, the 3. Balkan Conference on Metallurgy will provide a unique opportunity for academic and industrial metallurgists from the Balkan countries and wider, to exchange ideas, expertise, and experience on topics related to the theme of the Conference - Balkan Metallurgy in Search for New Ways of Development. The aim of the organizers was to bring together distinguished experts, not only to present their work, but also to discuss the major scientific and technological challenges facing metallurgy in this millennium.The 6 sections of the conference were entitled: Section A: Extractive metallurgy; Section B: Physical metallurgy and materials science - ferrous metals and non ferrous metals; Section C: Management, maintenance control and optimization of metallurgical processes; Section D: New technologies and techniques; Section E: Refractory and powder; Section F: Corrosion and protection of metals. Papers relevant to INIS are indexed separately.

  19. Proceedings of papers. 3. Balkan Metallurgical Conference

    International Nuclear Information System (INIS)

    Mickovski, Jovan

    2003-01-01

    This Conference aims to be a central event in the metallurgy research of Balkan, fulfilling the goals to present the most outstanding relevant developments in modern metallurgy; to inspire high standards of excellence in pure and applied metallurgy research; to attract outstanding scientists to present central lectures on modem metallurgical research, and on the challenges imposed by the needs of society; to inspire the young generation of metallurgists in Balkan and other countries. Following these lines, the 3. Balkan Conference on Metallurgy will provide a unique opportunity for academic and industrial metallurgists from the Balkan countries and wider, to exchange ideas, expertise, and experience on topics related to the theme of the Conference - Balkan Metallurgy in Search for New Ways of Development. The aim of the organizers was to bring together distinguished experts, not only to present their work, but also to discuss the major scientific and technological challenges facing metallurgy in this millennium.The 6 sections of the conference were entitled: Section A: Extractive metallurgy; Section B: Physical metallurgy and materials science - ferrous metals and non ferrous metals; Section C: Management, maintenance control and optimization of metallurgical processes; Section D: New technologies and techniques; Section E: Refractory and powder; Section F: Corrosion and protection of metals. Papers relevant to INIS are indexed separately

  20. Ideate about building green mine of uranium mining and metallurgy

    International Nuclear Information System (INIS)

    Shi Zuyuan

    2012-01-01

    Analysing the current situation of uranium mining and metallurgy; Setting up goals for green uranium mining and metallurgy, its fundamental conditions, Contents and measures. Putting forward an idea to combine green uranium mining and metallurgy with the state target for green mining, and keeping its own characteristics. (author)

  1. Metallurgy in the Czech Republic: a spatio-temporal view

    Directory of Open Access Journals (Sweden)

    J. Suchacek

    2017-01-01

    Full Text Available The objective of this paper is to introduce the stochastic input-output model of the impact of metallurgy sector on the Czech economy. Contrary to original input-output model, which is of deterministic nature, we reckon with interval estimates of the development of metallurgy sector. They help us to surpass deterministic impediments when analyzing and forecasting the possible developmental tendencies of metallurgy sector in various economies.

  2. Nuclear energy in metallurgy

    Energy Technology Data Exchange (ETDEWEB)

    Jirak, Z; Malik, J; Vrba, J

    1976-01-01

    The present power situation and its estimated development with a view to metallurgy is presented. The possibilities of the development of Czechoslovak metallurgy are described with regard to conventional fuels and to nuclear power applications. The programme of the use of nuclear power in countries with a highly developed metallurgical industry, such as Japan, the FRG, etc., is presented and the technical pre-requisites for the use of nuclear power in metallurgy, namely the use of high temperature reactors and their incorporation in nuclear metallurgical complexes are discussed. The problems are indicated of the selection of suitable materials for high temperature reactors and the experience is described with the operation of such equipment. The results are given of the analysis of 10 variants of the model of a nuclear metallurgical complex manufacturing 1000 tons of sponge iron per day and having four main technological circuits (the helium circuit, the steam circuit, the reduction gas circuit and the cycle of metallurgical processes). An estimate is given of the capital costs of building a high temperature reactor, a power plant and a metallurgical complex with the reactor. The costs are also given of steel and power production in a nuclear metallurgical complex.

  3. Inhibitive Action of Ferrous Gluconate on Aluminum Alloy in Saline Environment

    Directory of Open Access Journals (Sweden)

    Patricia Abimbola Idowu Popoola

    2013-01-01

    Full Text Available The corrosion of aluminum in saline environment in the presence of ferrous gluconate was studied using weight loss and linear polarization methods. The corrosion rates were studied in different concentrations of ferrous gluconate 0.5, 1.0, 1.5, and 2.0 g/mL at 28°C. Experimental results revealed that ferrous gluconate in saline environment reduced the corrosion rate of aluminum alloy at the different concentrations studied. The minimum inhibition efficiency was obtained at 1.5 g/mL concentration of inhibitor while the optimum inhibition efficiency was achieved with 1.0 g/mL inhibitor concentration. The results showed that adsorption of ferrous gluconate on the aluminium alloy surface fits Langmuir adsorption isotherm. The potentiodynamic polarization results showed that ferrous gluconate is a mixed type inhibitor. Ferrous gluconate acted as an effective inhibitor for aluminium alloy within the temperature and concentration range studied. The data obtained from weight loss and potentiodynamic polarization methods were in good agreement.

  4. Current programmes on physical metallurgy and related areas in BARC

    International Nuclear Information System (INIS)

    1994-01-01

    Current research and development programmes on physical metallurgy and related areas from the following Divisions of Bhabha Atomic Research Centre are included in this report : Atomic Fuels Division, High Pressure Physics Division, Metallurgy Division, Radio Metallurgy Division, Solid State Physics Division. Important publications corresponding to each activity have also been listed. (author)

  5. The extractive metallurgy of gold

    Science.gov (United States)

    Kongolo, K.; Mwema, M. D.

    1998-12-01

    Mössbauer spectroscopy has been successfully used in investigation of the gold compounds present in ores and the gold species which occur during the process metallurgy of this metal. This paper is a survey of the basic recovery methods and techniques used in extractive metallurgy of gold. Process fundamentals on mineral processing, ore leaching, zinc dust cementation, adsorption on activated carbon, electrowinning and refining are examined. The recovery of gold as a by-product of the copper industry is also described. Alternative processing methods are indicated in order to shed light on new interesting research topics where Mössbauer spectroscopy could be applied.

  6. The extractive metallurgy of gold

    International Nuclear Information System (INIS)

    Kongolo, K.; Mwema, M.D.

    1998-01-01

    Moessbauer spectroscopy has been successfully used in investigation of the gold compounds present in ores and the gold species which occur during the process metallurgy of this metal. This paper is a survey of the basic recovery methods and techniques used in extractive metallurgy of gold. Process fundamentals on mineral processing, ore leaching, zinc dust cementation, adsorption on activated carbon, electrowinning and refining are examined. The recovery of gold as a by-product of the copper industry is also described. Alternative processing methods are indicated in order to shed light on new interesting research topics where Moessbauer spectroscopy could be applied

  7. The extractive metallurgy of gold

    Energy Technology Data Exchange (ETDEWEB)

    Kongolo, K.; Mwema, M.D. [University of Lubumbashi, Zaire, Gecamines Metallurgical Research Centre, Likasi, Zaire, c/o Gecamines Brussels (Belgium)

    1998-12-15

    Moessbauer spectroscopy has been successfully used in investigation of the gold compounds present in ores and the gold species which occur during the process metallurgy of this metal. This paper is a survey of the basic recovery methods and techniques used in extractive metallurgy of gold. Process fundamentals on mineral processing, ore leaching, zinc dust cementation, adsorption on activated carbon, electrowinning and refining are examined. The recovery of gold as a by-product of the copper industry is also described. Alternative processing methods are indicated in order to shed light on new interesting research topics where Moessbauer spectroscopy could be applied.

  8. Innovative Production of Polyvinychloride on the Basis of Vertical Integration of Business and Cluster Organisation

    Science.gov (United States)

    Kudryashova, Irina; Zakharova, Natalia; Kharlampenkov, Evgeniy

    2017-11-01

    The paper presents the results of the research of the world and Russian market of polyvinyl chloride (PVC), a comparative assessment is made and the similarities and differences of these segments at the present have been identified. The theoretical possibility of considerable prospects of the development of domestic production of PVC is justified, ensure that it can achieve import substitution and export substitutionof this product in Russia. Based on the theoryof value chains and cluster organization of the enterprises of coal and chemical industries, ferrous metallurgy and other enterprises of Kuzbass have been proposed new technological solutions for the production of PVC, taking into account regional features of naturalresource base and capacity of national and world markets. It is established that the organization of production of PVC, using coal chemistry technology can be a promising growth point for the business of the Kemerovo region, will help to diversify the coal industry, to expand its product structure and export potential of the region, increase its competitiveness.

  9. Electron microscopy in metallurgy

    International Nuclear Information System (INIS)

    Loretto, M.H.

    1980-01-01

    The aim of this paper is to review briefly the contribution which (TEM) transmission electron microscopy (including high voltage electron microscopy (HVEM)) has made to metallurgy. Since it is straightforward with modern electron microscopes to extract the crystallographic information which provides the basis for any interpretation, the major problem in most metallurgical work lies in assessing how the structure (which TEM has characterised) has arisen and which properties of the specimen can be understood in terms of this structure. Radiation damage, quenching, phase transformations, grain boundaries and plastic deformation have been the main fields in which TEM has contributed significantly. After briefly summarising the role of TEM in each field, examples of recent work will be used to indicate current TEM activity in physical metallurgy. (author)

  10. Permanent magnets and its production by powder metallurgy

    Directory of Open Access Journals (Sweden)

    Enrique Herraiz Lalana

    2018-06-01

    Full Text Available In this work, the historical relationship between permanent magnets and powder metallurgy is reviewed. Powder metallurgy is a manufacturing technique based on the compaction of powders that are sintered to create a solid product. This technique was used in the production of permanent magnets for the first time in the 18th century and, nowadays, most permanent magnetic materials are manufacturing by this mean. Magnetic properties are highly dependent on the microstructure of the final product, the magnetic alignment of domains and presence of porosity, to mention a few, and powder metallurgy enables fine control of these factors.

  11. A spectroscopic and surface microhardness study of enamel exposed to beverages supplemented with ferrous fumarate and ferrous sulfate. A randomized in vitro trial.

    Science.gov (United States)

    Xavier, Arun M; Rai, Kavita; Hegde, Amitha M; Shetty, Suchetha

    2016-06-01

    To compare the efficacy between supplementing ferrous fumarate and ferrous sulfate to carbonated beverages by recording the in vitro mineral loss and surface microhardness (SMH) changes in human enamel. 120 enamel blocks each (from primary and permanent teeth) were uniformly prepared and the initial SMH was recorded. These enamel specimens were equally divided (n = 60) for their respective beverage treatment in Group 1 (2 mmol/L ferrous sulfate) and Group 2 (2 mmol/L ferrous fumarate). Each group was further divided into three subgroups as Coca-Cola, Sprite and mineral water (n= 10). The specimens were subjected to three repetitive cycles of respective treatment for a 5-minute incubation period, equally interspaced by 5-minute storage in artificial saliva. The calcium and phosphate released after each cycle were analyzed spectrophotometrically and the final SMH recorded. The results were tested using student's t-test, one-way ANOVA and Wilcoxon signed rank test (P Coca-Cola (P < 0.005).

  12. Application of tracer techniques and technical means in ferrous, non-ferrous and hydrometallurgy

    International Nuclear Information System (INIS)

    Chizhek, L.; Myshak, F.; Shtrba, J.

    1979-01-01

    Brief data are given about the results of joint investigations and developments of the problems of radioisotope methods and technical means application in ferrous and hydrometallurgy, obtained during the period of 1976-1977. Development of these problems was done in the frameworks of the plan of scientific and technical cooperation of the CMEA member-states and Yugoslavia. Results are given of the development of following themes: investigation of metallurgic processes by means of activation analysis; investidations of metallurgic processes by means of autoradiography and X-ray feuorescent analysis; control and automatization of metallurgic processes by means of radioisotope instruments; investigation of processes of melting of cast iron and steel as well as of processes of treatment of metals by means of the radioactive indicators method, activation analysis and radioisotope instruments; application of the radioisotope methods and technical means for investigation of processes of production of non-ferrous metals; application of the radioisotope methods for investigations of the hydrometallurgy processes [ru

  13. Environmental protection technologies and prospect for uranium mining and metallurgy in China

    International Nuclear Information System (INIS)

    Pan Yingjie

    2002-01-01

    Based on practices of production and environmental protection of China's uranium mining and metallurgy, control and protection of the three wastes in uranium mining and metallurgy are discussed. Prospects for environmental protection technologies of uranium mining and metallurgy is made

  14. Metallurgical aspects of welding. Ferrous and nonferrous materials. 4. new rev. ed.

    International Nuclear Information System (INIS)

    Schulze, Guenter

    2010-01-01

    This is the fourth edition of the standard work on welding metallurgy. The various problems of ferrous and nonferrous materials in the welding process are presented in great detail. In order to prevent corrosion of welded constructions, metallurgical properties and problems of all important technical materials are discussed, i.e. alloyed and unalloyed steels, cast iron materials, and the most relevant nonferrous materials. At the end of each chapter, the interested reader will find exercises for self-studies. Some of these can be solved using the material presented in the book while others are intended for deepening and further training. Easy examples (with solutions) are found all over the book; they are helpful because they provide information on underlying mechanisms and interdependences that are not obvious at first glance. The information was adapted to new EURO standards and international standards (up to March 2009) as far as these are relevant to Germany. New information is provided, e.g., on new steel standards (constructional steels according to DIN EN 10025), heat-treatable steels according to DIN EN 10025-6 and DIN EN 10083, high-alloy steels according to DIN EN 10088, and filler materials for steel welding according to DIN EN ISO 2560. The systematics of the ''law of cohabitation'' was applied to welding engineering for the first time here. (orig.) [de

  15. Introduction to powder metallurgy processes for titanium manufacturing

    International Nuclear Information System (INIS)

    Esteban, P. G.; Bolzoni, L.; Ruiz-Navas, E. M.; Gordo, E.

    2011-01-01

    The development of new extraction processes to produce titanium in powder form leads Powder Metallurgy to an advantage position among the manufacturing processes for titanium. The cost reduction of base material, coupled with the economy of the powder metallurgy processes, give titanium industry the chance to diversify its products, which could lead to production volumes able to stabilise the price of the metal. This work reviews some of the Powder Metallurgy techniques for the manufacturing of titanium parts, and describes the two typical approaches for titanium manufacturing: Blending Elemental and Prealloyed Powders. Among others, conventional pressing and sintering are described, which are compared with cold and hot isostatic pressing techniques. Real and potential applications are described. (Author) 71 refs.

  16. Advanced powder metallurgy aluminum alloys and composites

    Science.gov (United States)

    Lisagor, W. B.; Stein, B. A.

    1982-01-01

    The differences between powder and ingot metallurgy processing of aluminum alloys are outlined. The potential payoff in the use of advanced powder metallurgy (PM) aluminum alloys in future transport aircraft is indicated. The national program to bring this technology to commercial fruition and the NASA Langley Research Center role in this program are briefly outlined. Some initial results of research in 2000-series PM alloys and composites that highlight the property improvements possible are given.

  17. Method of activating an article of passive ferrous or non-ferrous metal prior to carburising, nitriding and /or nitrocarburising

    DEFF Research Database (Denmark)

    2011-01-01

    Source: US2012111456A A method of activating an article of passive ferrous or non-ferrous metal by heating at least one compound containing nitrogen and carbon, wherein the article is treated with gaseous species derived from the compound. The activated article can be subsequently carburised......, nitrided or nitrocarburised in shorter time at lower temperature and resulting superior mechanical properties compared with non-activated articles and even articles of stainless steel, nickel alloy, cobalt alloy or titanium based material can be carburised, nitrided or nitrocarburised....

  18. Copper alloys with improved properties: standard ingot metallurgy vs. powder metallurgy

    Directory of Open Access Journals (Sweden)

    Milan T. Jovanović

    2014-09-01

    Full Text Available Three copper-based alloys: two composites reinforced with Al2O3 particles and processed through powder metallurgy (P/M route, i.e. by internal oxidation (Cu-2.5Al composite and by mechanical alloying (Cu-4.7Al2O3 and Cu-0.4Cr-0.08Zr alloy produced by ingot metallurgy (vacuum melting and casting were the object of this investigation. Light microscope and scanning electron microscope (SEM equipped with electron X-ray spectrometer (EDS were used for microstructural characterization. Microhardness and electrical conductivity were also measured. Compared to composite materials, Cu-0.4Cr-0.08Zr alloy possesses highest electrical conductivity in the range from 20 to 800 ℃, whereas the lowest conductivity shows composite Cu-2.5Al processed by internal oxidation. In spite to somewhat lower electrical conductivity (probably due to inadequate density, Cu-2.5Al composite exhibits thermal stability enabling its application at much higher temperatures than materials processed by mechanical alloying or by vacuum melting and casting.

  19. Preparation of nitinol by non-conventional powder metallurgy techniques

    Czech Academy of Sciences Publication Activity Database

    Novák, P.; Moravec, H.; Salvetr, P.; Průša, F.; Drahokoupil, Jan; Kopeček, Jaromír; Karlík, M.; Kubatík, Tomáš František

    2015-01-01

    Roč. 31, č. 15 (2015), s. 1886-1893 ISSN 0267-0836 R&D Projects: GA ČR(CZ) GA14-03044S Institutional support: RVO:68378271 ; RVO:61389021 Keywords : shape memory alloys * SHS process * SEM * powder metallurgy Subject RIV: JG - Metallurgy Impact factor: 1.008, year: 2015

  20. Effect of calcium oxide on the efficiency of ferrous ion oxidation and total iron precipitation during ferrous ion oxidation in simulated acid mine drainage treatment with inoculation of Acidithiobacillus ferrooxidans.

    Science.gov (United States)

    Liu, Fenwu; Zhou, Jun; Jin, Tongjun; Zhang, Shasha; Liu, Lanlan

    2016-01-01

    Calcium oxide was added into ferrous ion oxidation system in the presence of Acidithiobacillus ferrooxidans at concentrations of 0-4.00 g/L. The pH, ferrous ion oxidation efficiency, total iron precipitation efficiency, and phase of the solid minerals harvested from different treatments were investigated during the ferrous ion oxidation process. In control check (CK) system, pH of the solution decreased from 2.81 to 2.25 when ferrous ions achieved complete oxidation after 72 h of Acidithiobacillus ferrooxidans incubation without the addition of calcium oxide, and total iron precipitation efficiency reached 20.2%. Efficiency of ferrous ion oxidation and total iron precipitation was significantly improved when the amount of calcium oxide added was ≤1.33 g/L, and the minerals harvested from systems were mainly a mixture of jarosite and schwertmannite. For example, the ferrous ion oxidation efficiency reached 100% at 60 h and total iron precipitation efficiency was increased to 32.1% at 72 h when 1.33 g/L of calcium oxide was added. However, ferrous ion oxidation and total iron precipitation for jarosite and schwertmannite formation were inhibited if the amount of calcium oxide added was above 2.67 g/L, and large amounts of calcium sulfate dihydrate were generated in systems.

  1. Structure and properties of powder metallurgy constructional steel of different densities

    International Nuclear Information System (INIS)

    Gulyaev, A.P.; Moskvina, T.P.

    1986-01-01

    A specific feature of powder metallurgy steels is porosity, the degree of which depends upon the method of their production. This article establishes the influence of a small amount of porosity on the mechanical properties of powder metallurgy constructional steel. The structure of heat-treated cast and powder metallurgy steels with different porosities are shown. The results of mechanical tests of the experimental steels with different porosities are shown. With an increase in porosity the nonmetallic inclusion rating of the powder metallurgy constructional steel increases, primarily as the result of the increase in the coarse particles, which is caused by the lower degree of plastic deformation in pressing. With an increase in porosity the mechanical properties of the powder metallurgy steel become poorer: the hardness and strength properties with a porosity of more than 3-5%, the plasticity with more than 1-2%, and the toughness even with a porosity of 1%

  2. Powder metallurgy - some economic considerations

    Energy Technology Data Exchange (ETDEWEB)

    Kassem, M.E.

    1982-01-01

    As a forming process powder metallurgy offers reductions in material and energy consumption. The engineering prerequisites and economics are discussed in relation to several industrial applications including automobile parts. 14 refs.

  3. Metallurgy Department publications 1988

    International Nuclear Information System (INIS)

    Schroeder Pedersen, A.; Bilde-Soerensen, J.B.

    1989-08-01

    A presentation (including abstracts) of scientific and technical publications and lectures by the staff of the Metallurgy Department during 1988 is given. The list comprises journal papers, conference papers, reports, lectures and poster presentations in the following catagories: Publications, Lectures and Poster Presentations. (author)

  4. Metallurgy Department publications 1989

    International Nuclear Information System (INIS)

    Horsewell, A.

    1990-08-01

    All publiclations by the staff of the Metallurgy Department during 1989 are listed. This list is divided into three sections as follows: Publications (journal and conference papers, reports); Lectures (public lecture presentations) and Posters (poster presentations at conferences and symposia). Abstracts are included. (author)

  5. Soil pollution with trace elements at selected sites in Romania studied by instrumental neutron activation analysis

    International Nuclear Information System (INIS)

    Pantelica, A.; Carmo Freitas, M. do; Ene, A.; Steinnes, E.

    2013-01-01

    Instrumental neutron activation analysis (INAA) was used to determine concentrations of 42 elements in samples of surface soil collected at seven sites polluted from various anthropogenic activities and a control site in a relatively clean area. Elements studied were Ag, Al, As, Au, Ba, Br, Ca, Cd, Ce, Co, Cr, Cs, Eu, Fe, Gd, Hf, Hg, K, La, Lu, Mg, Mn, Mo, Na, Nd, Ni, Rb, Sb, Sc, Se, Sm, Sr, Ta, Tb, Th, Ti, U, V, W, Yb, Zn, and Zr. The results are compared with data for trace elements atmospheric deposition in lichen transplants from the same sites. The most severe soil contamination was observed at Copsa Mica from non-ferrous metallurgy. Appreciable soil contamination was also indicated at Baia Mare (non-ferrous mining and metallurgy), Deva (coal-fired power plant, cement and building materials industry), Galati (ferrous metallurgy), Magurele and Afumati (general urban pollution), and Oradea (chemical and light industries). In most cases excessive levels of toxic metals in soils matched correspondingly high values in lichen transplants. Compared to Romanian norms, legal upper limits were exceeded for Zn and Cd at Copsa Mica. Also, As and Sb occurred in excessive levels at given sites. (orig.)

  6. Soil pollution with trace elements at selected sites in Romania studied by instrumental neutron activation analysis

    Energy Technology Data Exchange (ETDEWEB)

    Pantelica, A. [Horia Hulubei National Institute for Physics and Nuclear Engineering (IFIN-HH), Magurele, Ilfov County (Romania); Carmo Freitas, M. do [Technological and Nuclear Institute (ITN), Sacavem (Portugal); Ene, A. [Dunarea de Jos Univ. of Galati (Romania). Dept. of Chemistry, Physics and Environment; Steinnes, E. [Norwegian Univ. of Science and Technology, Trondheim (Norway). Dept. of Chemistry

    2013-03-01

    Instrumental neutron activation analysis (INAA) was used to determine concentrations of 42 elements in samples of surface soil collected at seven sites polluted from various anthropogenic activities and a control site in a relatively clean area. Elements studied were Ag, Al, As, Au, Ba, Br, Ca, Cd, Ce, Co, Cr, Cs, Eu, Fe, Gd, Hf, Hg, K, La, Lu, Mg, Mn, Mo, Na, Nd, Ni, Rb, Sb, Sc, Se, Sm, Sr, Ta, Tb, Th, Ti, U, V, W, Yb, Zn, and Zr. The results are compared with data for trace elements atmospheric deposition in lichen transplants from the same sites. The most severe soil contamination was observed at Copsa Mica from non-ferrous metallurgy. Appreciable soil contamination was also indicated at Baia Mare (non-ferrous mining and metallurgy), Deva (coal-fired power plant, cement and building materials industry), Galati (ferrous metallurgy), Magurele and Afumati (general urban pollution), and Oradea (chemical and light industries). In most cases excessive levels of toxic metals in soils matched correspondingly high values in lichen transplants. Compared to Romanian norms, legal upper limits were exceeded for Zn and Cd at Copsa Mica. Also, As and Sb occurred in excessive levels at given sites. (orig.)

  7. Metallurgy and Heat Treating. Welding Module 7. Instructor's Guide.

    Science.gov (United States)

    Missouri Univ., Columbia. Instructional Materials Lab.

    This guide is intended to assist vocational educators in teaching a three-unit module in metallurgy and heat treating. The module is part of a welding curriculum that has been designed to be totally integrated with Missouri's Vocational Instruction Management System. The basic principles of metallurgy and heat treatment and techniques for…

  8. Metallurgy and foundry practice. German-English. With 40,000 citations. Metallurgie und Giessereitechnik. Deutsch-Englisch. Mit etwa 40,000 Wortstellen

    Energy Technology Data Exchange (ETDEWEB)

    Stoelzel, K [ed.

    1986-01-01

    The dictionary represents the German-English terminology of the broad field of metallurgy (the dressing of ores and fluxes, pig iron and steel making, powder and nonferrous metallurgy, forming processes etc.) as well as of the broad field of foundry practice. Apart from the theoretical fundamental principles emphasis is on the problems of materials working and materials testing. Moreover, the dictionary considers a number of technical terms concerning the hardening, surface treatment and corrosion of materials.

  9. Passive Aerial Grasping of Ferrous Objects

    KAUST Repository

    Fiaz, Usman Amin

    2017-10-19

    Aerial transportation is probably the most efficient way to supply quick and effective aid especially in cases of emergency like search and rescue operations. Thus the ability to grasp and deliver objects is of vital importance in all sorts of unmanned and autonomous aerial operations. We detail a simple yet novel approach for aerial grasping of ferrous objects using a passive magnetic pickup and an impulse based drop mechanism. The design enables our gripper to grasp ferrous objects using single as well as multiple gripping pads, with visual as well as pickup and drop feedback. We describe the various components of the gripper with emphasis on its low mass and high lift capability since weight is a matter of high consideration in all aerial applications. In addition, we investigate and address the issues that may cause our design to fail. We demonstrate by experiments that the proposed design is robust and effective, based on its high payload capability, its sturdiness against possible slide during aggressive aerial maneuvers, and optimum performance of the drop mechanism for the designed range of payloads. We also show that the gripper is able to pick up and drop a single as well as multiple ferrous objects of different shapes, curvature, and inclination, which also involves picking up an object and then grasping the next, while keeping hold of the previous one.

  10. Passive Aerial Grasping of Ferrous Objects

    KAUST Repository

    Fiaz, Usman; Toumi, Noureddine; Shamma, Jeff S.

    2017-01-01

    Aerial transportation is probably the most efficient way to supply quick and effective aid especially in cases of emergency like search and rescue operations. Thus the ability to grasp and deliver objects is of vital importance in all sorts of unmanned and autonomous aerial operations. We detail a simple yet novel approach for aerial grasping of ferrous objects using a passive magnetic pickup and an impulse based drop mechanism. The design enables our gripper to grasp ferrous objects using single as well as multiple gripping pads, with visual as well as pickup and drop feedback. We describe the various components of the gripper with emphasis on its low mass and high lift capability since weight is a matter of high consideration in all aerial applications. In addition, we investigate and address the issues that may cause our design to fail. We demonstrate by experiments that the proposed design is robust and effective, based on its high payload capability, its sturdiness against possible slide during aggressive aerial maneuvers, and optimum performance of the drop mechanism for the designed range of payloads. We also show that the gripper is able to pick up and drop a single as well as multiple ferrous objects of different shapes, curvature, and inclination, which also involves picking up an object and then grasping the next, while keeping hold of the previous one.

  11. Welding Metallurgy and Weldability of Stainless Steels

    Science.gov (United States)

    Lippold, John C.; Kotecki, Damian J.

    2005-03-01

    Welding Metallurgy and Weldability of Stainless Steels, the first book in over twenty years to address welding metallurgy and weldability issues associated with stainless steel, offers the most up-to-date and comprehensive treatment of these topics currently available. The authors emphasize fundamental metallurgical principles governing microstructure evolution and property development of stainless steels, including martensistic, ferric, austenitic, duplex, and precipitation hardening grades. They present a logical and well-organized look at the history, evolution, and primary uses of each stainless steel, including detailed descriptions of the associated weldability issues.

  12. 7th european metallurgical conference EMC 2013

    Directory of Open Access Journals (Sweden)

    Srećko R. Stopić

    2014-02-01

    Full Text Available From June 23 – 26, 2013, the GDMB Society for Mining, Metallurgy, Resource and Environmental Technology organized 7th European Metallurgical Conference (EMC 2013 in Weimar, Germany. The previous European metallurgical conferences were organized by  the GDMB in Friedrichshafen (2001, Hanover (2003, Leipzig (2005, Duesseldorf (2007, Innsbruck (2009, and Duesseldorf (2011. The GDMB is a non-profit organization from Clausthal, Germany,,focused on combining science with practical experience in metallurgy, mining, materials engineering, mineral processing, recycling and refining of metals, and  manufacturing of semi- and finishing products. The European Metallurgical conference EMC is one of the most well-known conferences worldwide in the field of non-ferrous metallurgy and is attended regularly by decision makers from industry and universities. The scientific program contained 6 plenary lectures and more than 130 presentations. An extensive poster exhibition was held, during which the authors had an opportunity to introduce their posters to the entire plenum as a part of a brief presentation., The € 500 worth “Poster Award EMC 2011 was awarded to Christoph Pichler from the Montan-University in Leoben, Austria. Not only the most important European countries were represented here, but also more than one third of the lecturers were from countries outside Europe (Canada, Japan, China, USA, South Africa, Australia. The origin of the participants reflects the aim of the organizers: to make this conference a worldwide platform for the scientific exchange of experience and information. The scientific presentations of the conference are presented in Proceedings: Vol. 1: Copper, Precious Metals, Waste effluents Treatment/ Biohydrometallurgical applications; Process Metallurgy, Bridging Non-Ferrous and Ferrous Metallurgy; Vol. 2: Lead and Zinc, Light metals, Sustainable technologies, Sustainable of non-ferrous metals production, Process Control

  13. Thermogravimetric control of intermediate compounds in uranium metallurgy

    International Nuclear Information System (INIS)

    Gasco Sanchez, L.; Fernandez Cellini, R.

    1959-01-01

    The thermal decomposition of some intermediate compounds in the metallurgy of the uranium as uranium peroxide, ammonium uranate, uranium and ammonium penta-fluoride, uranium tetrafluoride and uranous oxide has been study by means of the Chevenard's thermo balance. Some data on pyrolysis of synthetic mixtures of intermediate compounds which may occasionally appear during the industrial process, are given. Thermogravimetric methods of control are suggested, usable in interesting products in the uranium metallurgy. (Author) 20 refs

  14. Biennial activity report of Metallurgy Division for 1989 and 1990

    International Nuclear Information System (INIS)

    Kamachi Mudali, U.; Muraleedharan, P.; Parameswaran, P.; Swaminathan, K.; Sreedharan, O.M.

    1993-01-01

    This is the first divisional biennial report of the Metallurgy Division of Indira Gandhi Centre for Atomic Research, for the year 1989-1990, after formation of the Metallurgy Division in September 1988. Major areas of work in the Division relate to aqueous corrosion and localised corrosion, stress corrosion cracking and liquid metal corrosion, high temperature oxidation, thermodynamic studies, physical metallurgy studies for structure-property correlations and failure analyses. The principal materials of studies have been the austenitic stainless steels, the current materials of construction in the Fast Breeder Test Reactor and the candidate materials for the Prototype Fast Breeder Reactor

  15. Biennial activity report of Metallurgy Programme - 1985 and 1986

    International Nuclear Information System (INIS)

    Mallika, C.; Sreenivasan, P.R.; Muraleedharan, P.; Shyamsunder, M.T.; Kuppuswami, P.; Sampath, N.; Bhaduri, A.K.; Sreedharan, O.M.

    1988-01-01

    The biennial activity report of the Metallurgy Programme of the Indira Gandhi Centre for Atomic Research covers the period of the years 1985 and 1986. Along with NDT, welding metallurgy, low cycle fatigue, creep and creep fatigue interactions, structure-property correlations, thermodynamics and corrosion metallurgy of alloy steels with respect to their compatibility with aqueous and liquid sodium environments continue to be the major thrust areas of the Programme. Some of the basic research contributions of the Programme are: the observation of uniform and homogeneous distribution of voids in cyclically deformed 304 SS, the role of grain boundaries and precipitation in dynamic strain ageing of 316 SS and the determination of the activities of component metals in 316 and 304 SS by metastable EMF method. (author)

  16. Industrial applications and metallurgy

    International Nuclear Information System (INIS)

    Torres M, N.; Melendrez C, G.; Morales, F.L.

    1989-01-01

    From 1961 the use of nuclear energy in the industrial field in Colombia has a big advance. Today nuclear isotopes are used by private companies in this kind of application the Area of Industrial Applications and Metallurgy was the institution section that has trained and has transferred the technology needed for this purpose

  17. Diffusion measurement in ferrous infused gel dosimeters

    International Nuclear Information System (INIS)

    Zahmatkesh, M. H.; Healy, B. J.

    2003-01-01

    Background: The compositions of Ferrous sulphate, Agarose and Xylenol orange dye and Ferrous sulphate, Gelatin and Xylenol orange dye in solution of distilled water and sulphuric acid are two tissue-equivalent gel dosimeters. Ionizing radiation causes oxidation of Fe 2+ ion to Fe 3+ ions which diffuse through the gel matrix and blur the image of absorbed dose over a period of hours after irradiation. Materials and methods: 25 m M sulphuric acid, 0.4 mm ferrous ammonium sulphate, 0.2 mm xylenol orange dye and 1% by weight agarose in distilled water named Agarose and Xylenol orange dye and 0.1 mm ferrous ammonium sulphate, 0.1 mm xylenol orange dye, 50 mm sulphuric acid and 5% by weight gelatin in distilled water named Gelatin and Xylenol orange dye are used as two gel dosimeters. All chemicals were supplied by Sigma Ald ridge Company, Germany. The gels were poured in Perspex casts and were irradiated to a beam of X ray from linear accelerators or X ray machine. Results: In this study diffusion coefficients of Agarose and Xylenol orange dye and Gelatin and Xylenol orange dye dosimeters have been measured through a computer program for different temperature. The ferric ion diffusion coefficient (D) for the Agarose and Xylenol orange dye and Gelatin and Xylenol orange dye dosimeters were measured as (1.19.±0.03) x 10 -2 cm 2 .hr -1 and (0.83±0.03) x 10 -2 cm 2 .hr -1 respectively at room temperature. Conclusion: For both dosimeters the diffusion coefficients decreased with gel storage temperatures down to 6 d ig C . Gelatin and Xylenol orange dye dosimeters have advantage of lower diffusion coefficient for a specified temperature

  18. Biennial activity report of Metallurgy Division for 1989 and 1990

    Energy Technology Data Exchange (ETDEWEB)

    Kamachi Mudali, U; Muraleedharan, P; Parameswaran, P; Swaminathan, K; Sreedharan, O M [eds.; Indira Gandhi Centre for Atomic Research, Kalpakkam (India)

    1994-12-31

    This is the first divisional biennial report of the Metallurgy Division of Indira Gandhi Centre for Atomic Research, for the year 1989-1990, after formation of the Metallurgy Division in September 1988. Major areas of work in the Division relate to aqueous corrosion and localised corrosion, stress corrosion cracking and liquid metal corrosion, high temperature oxidation, thermodynamic studies, physical metallurgy studies for structure-property correlations and failure analyses. The principal materials of studies have been the austenitic stainless steels, the current materials of construction in the Fast Breeder Test Reactor and the candidate materials for the Prototype Fast Breeder Reactor 7 figs., 6 tabs., 2 ills.

  19. Mechanical and microstructural characterization of powder metallurgy CoCrNi medium entropy alloy

    Czech Academy of Sciences Publication Activity Database

    Moravčík, I.; Čížek, Jan; Kováčová, Z.; Nejezchlebová, J.; Kitzmantel, M.; Neubauer, E.; Kuběna, Ivo; Horník, Vít; Dlouhý, I.

    2017-01-01

    Roč. 701, July (2017), s. 370-380 ISSN 0921-5093 Institutional support: RVO:61389021 ; RVO:68081723 Keywords : tensile test * mechanical alloying * plastic ity * mechanical characterization * powder metallurgy Subject RIV: JG - Metallurgy; JG - Metallurgy (UFM-A) OBOR OECD: Materials engineering; Materials engineering (UFM-A) Impact factor: 3.094, year: 2016 https://www.sciencedirect.com/science/article/pii/S0921509317308535

  20. Densification of powder metallurgy billets by a roll consolidation technique

    Science.gov (United States)

    Sellman, W. H.; Weinberger, W. R.

    1973-01-01

    Container design is used to convert partially densified powder metallurgy compacts into fully densified slabs in one processing step. Technique improves product yield, lowers costs and yields great flexibility in process scale-up. Technique is applicable to all types of fabricable metallic materials that are produced from powder metallurgy process.

  1. Radiation technologies in metallurgy and machinery

    International Nuclear Information System (INIS)

    Meshkov, I.N.

    1990-01-01

    Applications of electron beam accelerators for technologies in metallurgy and machinery are discussed. Processes described are provided with special industrial accelerators, developed in the Institute of Nuclear Physics, Novosibirsk. (author)

  2. [Respiratory diseases in metallurgy production workers].

    Science.gov (United States)

    Shliapnikov, D M; Vlasova, E M; Ponomareva, T A

    2012-01-01

    The authors identified features of respiratory diseases in workers of various metallurgy workshops. Cause-effect relationships are defined between occupational risk factors and respiratory diseases, with determining the affection level.

  3. Ferrous ammonium phosphate (FeNH₄PO₄) as a new food fortificant: iron bioavailability compared to ferrous sulfate and ferric pyrophosphate from an instant milk drink.

    Science.gov (United States)

    Walczyk, Thomas; Kastenmayer, Peter; Storcksdieck Genannt Bonsmann, Stefan; Zeder, Christophe; Grathwohl, Dominik; Hurrell, Richard F

    2013-06-01

    The main purpose of this study was to establish bioavailability data in humans for the new (Fe) fortification compound ferrous ammonium phosphate (FAP), which was specially developed for fortification of difficult-to-fortify foods where soluble Fe compounds cannot be used due to their negative impact on product stability. A double-blind, randomized clinical trial with cross-over design was conducted to obtain bioavailability data for FAP in humans. In this trial, Fe absorption from FAP-fortified full-cream milk powder was compared to that from ferric pyrophosphate (FPP) and ferrous sulfate. Fe absorption was determined in 38 young women using the erythrocyte incorporation dual stable isotope technique (⁵⁷Fe, ⁵⁸Fe). Geometric mean Fe absorption from ferrous sulfate, FAP and FPP was 10.4, 7.4 and 3.3 %, respectively. Fe from FAP was significantly better absorbed from milk than Fe from FPP (p soluble reference compound (p = 0.0002). Absorption ratios of FAP and FPP relative to ferrous sulfate as a measure of relative bioavailability were 0.71 and 0.32, respectively. The results of the present studies show that replacing FPP with FAP in full-cream milk could significantly improve iron bioavailability.

  4. DETERMINATION OF THE RATES AND PRODUCTS OF FERROUS IRON OXIDATION IN ARSENIC-CONTAMINATED POND WATER.

    Science.gov (United States)

    Dissolved ferrous iron and arsenic in the presence of insufficient oxygenated ground water is released into a pond. When the mixing of ferrous iron and oxygenated water within the pond occurs, the ferrous iron is oxidized and precipitated as an iron oxide. Groups of experiments...

  5. Problems of zirconium metal production in Czechoslovakia

    International Nuclear Information System (INIS)

    Vareka, J.; Vaclavik, E.

    1975-01-01

    The problems are summed up of the production and quality control of zirconium sponge. A survey is given of industrial applications of zirconium in form of pure metal or alloys in nuclear power production, ferrous and non-ferrous metallurgy, chemical engineering and electrical engineering. A survey is also presented of the manufacture of zirconium metal in advanced capitalist countries. (J.B.)

  6. Research of radiation protection standard system in uranium mining and metallurgy

    International Nuclear Information System (INIS)

    Lian Guoxi; Song Liquan; Xie Zhanjun

    2011-01-01

    The contents of radiation and environment protection standards used in uranium mining and metallurgy are analyzed and the existent problems in current standard system are pointed out. A new standard system is established according to theory of systematology and the actuality of uranium mining and metallurgy. Some standard checklists which need to be complemented, corrected, deleted and used during the work of perfection and complementation of standard system are presented. The procedures of establishing new standard system are described, and some suggestions on the establishment and implementation of radiation protection standard system in uranium mining and metallurgy are put forward. (authors)

  7. Ferrous bisglycinate 25 mg iron is as effective as ferrous sulfate 50 mg iron in the prophylaxis of iron deficiency and anemia during pregnancy in a randomized trial

    DEFF Research Database (Denmark)

    Milman, Nils; Jønsson, Lisbeth; Dyre, Pernille

    2014-01-01

    OBJECTIVE: To compare the effects of oral ferrous bisglycinate 25 mg iron/day vs. ferrous sulfate 50 mg iron/day in the prevention of iron deficiency (ID) and iron deficiency anemia (IDA) in pregnant women. Design: Randomized, double-blind, intention-to-treat study. Setting: Antenatal care clinic...

  8. The use of tubular belt conveyors for the industrial waste of enterprises

    Directory of Open Access Journals (Sweden)

    S. Ya. Davydov

    2017-12-01

    Full Text Available The methods of processing slag of electrolyzers and reverberatory furnaces slag of secondary aluminum production, obtained after extracting aluminum, as well as ash and slag of thermal power plants, hydro plants, waste of ferrous metallurgy in the construction industry are presented in this work. Tubular belt conveyor (TBC with the use of special expensive tapes, are widely used abroad for moving industrial raw materials. It is also used in Russia (Lebedinsky ore-dressing and processing enterprise and Reftinskaya hydro power. A tape which is rolled in a tube allows to improve the sanitary conditions of labor, to ensure the full safety of cargo, to exclude the harmful effects of aggressive chemical cargoes at the metal of the conveyor, extending its service life. There is an opportunity to convey materials under the angle of 20–25°. The main drawback of TBC, which exist today, is that they are working on an especially patented tape, which is very expensive and it is not produced in Russia. The costs of its replacement are comparable to the price of the pipeline. The Russian customers have already faced this problem. The components are not produced in Russia either, and the cost of their subsequent purchases increases dramatically. The technical parameters of TBC of the Lebedinsky ore-dressing and processing enterprise and the Reftinskaya hydro power, as well as a comparative table on the use of TBC are presented in this work. Lists of the advantages of TBC are also adduced. The characteristic of TBC Contitech are given. The use of modern anti-static and flame retardant polymeric materials in the manufacture of the rollers will allow further progress in solving the issues of safe operation of belt conveyors. Such important parameters as reliability and maintainability were taken into account while constructing these conveyors. The tests to replace the metal clips with the rollers, which are made of anti-static polymers are carried out. This

  9. Weldability of powder-metallurgy molybdenum with low oxygen content

    International Nuclear Information System (INIS)

    Hiraoka, Yutaka; Okada, Masatoshi

    1987-01-01

    Relationships between the formation of weld pores and the chemical compositions in powder-metallurgy molybdenum were investigated. It is suggested that almost 100% of Ca and Mg form oxides. In contrast, Fe, Ni, Cr and Al, Si only partly form oxides. A powder-metallurgy molybdenum containing less than 84 at.ppm oxygen did not show any large weld pores. The reduction of the oxygen content was achieved by purifying the molybdenum powder. (orig.) [de

  10. Foundations of powder metallurgy

    International Nuclear Information System (INIS)

    Libenson, G.A.

    1987-01-01

    Consideration is being given to physicochemical foundations and technology of metal powders, moulding and sintering of bars, made of them or their mixtures with nonmetal powders. Data on he design of basic equipment used in the processes of powder metallurgy and its servicing are presented. General requirements of safety engineering when fabricating metal powders and products of them are mentioned

  11. Application of powder metallurgy beryllium in Beijing spectrometer III beam pipe

    International Nuclear Information System (INIS)

    Zheng Lifang; Li Xunfeng; Wang Li; Ji Quan; Liu Jianping

    2008-01-01

    According to the requirements of Beijing Spectrometer III (BESIII) beam pipe, the physical properties of several materials were compared and powder metallurgy beryllium was chosen as the material for the central pipe of the BES III beam pipe. Weight-loss method was used to study the corrosion of powder metallurgy beryllium in No. 1 oil for electron discharge machining (EDM-1). The result shows that the anticorrosive property of powder metallurgy beryllium in EDM-1 is high. The corrosion rate, 4.18 x 10 -7 kg· m -2 ·h -1 in initial stage, becomes small with the lapse of the time and stabilizes at 1.54 x 10 -7 kg·m -2 ·h -1 at last. It can be estimated that the powder metallurgy beryllium will be corroded 19.9 μm in the depth in 10 years and it accounts for 3.32% of the smallest thickness of the central pipe, which satisfies the requirements of the BESIII. (authors)

  12. Removal of cyanide compounds from coking wastewater by ferrous sulfate: Improvement of biodegradability.

    Science.gov (United States)

    Yu, Xubiao; Xu, Ronghua; Wei, Chaohai; Wu, Haizhen

    2016-01-25

    The effect of ferrous sulfate (FeSO4) treatment on the removal of cyanide compounds and the improvement of biodegradability of coking wastewater were investigated by varying Fe:TCN molar ratios. Results suggested that the reaction between FeSO4 and coking wastewater was a two-step process. At the first step, i.e., 0≤Fe:TCN≤1.0, the reaction mechanisms were dominated by the precipitation of FeS, the complexation of CN(-), and the coagulation of organic compounds. The COD of coking wastewater decreased from 3748.1 mg/L to 3450.2 mg/L, but BOD5:COD (B/C) was improved from 0.30 to 0.51. At the second step, i.e., 1.0cyanide compounds by ferrous ions was the dominating mechanism. The COD showed a continuous increase to 3542.2 mg/L (Fe:TCN=3.2) due to the accumulated ferrous ions in coking wastewater. Moreover, B/C decreased progressively to 0.35, which was attributed to the negative effects of excess ferrous ions on biodegradability. To improve coking wastewater's biodegradability, a minimum ferrous dosage is required to complete the first step reaction. However, the optimum ferrous dosage should be determined to control a safe residual TCN in coking wastewater for the further biological treatment. Copyright © 2015 Elsevier B.V. All rights reserved.

  13. Computational thermodynamics in electric current metallurgy

    DEFF Research Database (Denmark)

    Bhowmik, Arghya; Qin, R.S.

    2015-01-01

    . The method has been validated against the analytical solution of current distribution and experimental observation of microstructure evolution. It provides a basis for the design, prediction and implementation of the electric current metallurgy. The applicability of the theory is discussed in the derivations.......A priori derivation for the extra free energy caused by the passing electric current in metal is presented. The analytical expression and its discrete format in support of the numerical calculation of thermodynamics in electric current metallurgy have been developed. This enables the calculation...... of electric current distribution, current induced temperature distribution and free energy sequence of various phase transitions in multiphase materials. The work is particularly suitable for the study of magnetic materials that contain various magnetic phases. The latter has not been considered in literature...

  14. Influence of physical culture and sports on health status of pupils of industrial city

    Directory of Open Access Journals (Sweden)

    Kapranov S.V.

    2013-08-01

    Full Text Available The aim was to study in the city with large enterprises of ferrous metallurgy and coke health of schoolchildren under the influence of physical education and sports. The research of blood pressure and heart rate (HR were 295 pupils aged 15-17 years, 390 - anthropometric study of body length, body weight, chest circumference and head, while the 584 teenagers - the prevalence of dental caries. HR assessment is made by comparing with the age norms, and indicators of physical development of pupils - centile method. It is shown that under the influence of employment morning gymnastics school students marked normalization of their heart rate. Waiver of physical exercise leads to a decrease in students in body length and circumference of the chest. Classes in morning exercises and sports are the factors antirisk caries among high school students. Proposed preventive recommendations.

  15. Tungsten and tungsten alloys by powder metallurgy

    International Nuclear Information System (INIS)

    Belhadjhamida, A.; German, R.M.

    1991-01-01

    Tungsten has a historical link with powder metallurgy and there is continued progress in expanding the available compositions and processing options. This paper starts with an introduction to the history of tungsten powder metallurgy and use this as a basis for analyzing some of the current trends. The literature base in tungsten processing is expanding and includes new alloys, microstructures, and processing routes. A few examples will be emphasize here to produce a frame work for this program, including description of sintering mechanisms for tungsten, liquid phase sintering advances, hot consolidation fundamentals, and options for complex shaping using powder injection modeling. For this base, subsequent presentations will expand on these fundamental advances

  16. Near-Net Shape Powder Metallurgy Rhenium Thruster

    Science.gov (United States)

    Leonhardt, Todd; Hamister, Mark; Carlen, Jan C.; Biaglow, James; Reed, Brian

    2001-01-01

    This paper describes the development of a method to produce a near-net shape (NNS) powder metallurgy (PM) rhenium combustion chamber of the size 445 N (100 lbf) used in a high performance liquid apogee engine. These engines are used in low earth Orbit and geostationary orbit for satellite positioning systems. The developments in near-net shape powder metallurgy rhenium combustion chambers reported in this paper will reduce manufacturing cost of the rhenium chambers by 25 percent, and reduce the manufacturing time by 30 to 40 percent. The quantity of rhenium metal powder used to produce a rhenium chamber is reduced by approximately 70 percent and the subsequent reduction in machining schedule and costs is nearly 50 percent.

  17. Application of the ecologically clean technology of mining metallurgy and power industry wastes recycling based on the use of electron beams

    International Nuclear Information System (INIS)

    Mazhrenova, N.R.; Askarova, G.Sh.

    1997-01-01

    Advantage of electron beam technologies application for industrial wastes recycling is illustrated for following trends: 1).Off gases of mining metallurgy and the thermal power plant can be refined from SO 2 and NO x toxic combination by means of their further chemical and radiation oxidation with following obtaining of acids on the base industrial accelerator ELV-8. In this method a radiation-chemical process in irradiated gas results in excited complexes, radicals and ion formation. Ion cause the activation of reaction chain which convert SO 2 and NO x toxic gases into the combination with high number of oxidation. In presence of water, coming from drip cooler, the combination of sulphuric and nitric acids neutralization results in the obtaining of ammonium solid combination which are mainly sulphates and nitrates; 2). For waste water refinement from organic pollution, for instance butyl xanthate, ions of heavy metals and etc.; 3). For non-ferrous, sparse and and dispersed metal extraction from the cinder and slag wastes. Different technological schemes for mineral extraction are elaborated

  18. Metallurgical examination of powder metallurgy uranium alloy welds

    International Nuclear Information System (INIS)

    Morrison, A.G.M.; Dobbins, A.G.; Holbert, R.K.; Doughty, M.W.

    1986-01-01

    Inertia welding provided a successful technique for joining full density, powder metallurgy uranium-6 wt pct niobium alloy. Initial joining attempts concentrated on the electron beam method, but this method failed to produce a sound weld. The electron beam welds and the inertia welds were evaluated by radiography and metallography. Electron beam welds were attempted on powder metallurgy plates which contained various levels of oxygen and nitrogen. All welds were porous. Sixteen inertia welds were made and all welds were radiographically sound. The tensile properties of the joints were found to be equivalent to the p/m base metal properties

  19. Metallurgy and properties of plasma spray formed materials

    Science.gov (United States)

    Mckechnie, T. N.; Liaw, Y. K.; Zimmerman, F. R.; Poorman, R. M.

    1992-01-01

    Understanding the fundamental metallurgy of vacuum plasma spray formed materials is the key to enhancing and developing full material properties. Investigations have shown that the microstructure of plasma sprayed materials must evolve from a powder splat morphology to a recrystallized grain structure to assure high strength and ductility. A fully, or near fully, dense material that exhibits a powder splat morphology will perform as a brittle material compared to a recrystallized grain structure for the same amount of porosity. Metallurgy and material properties of nickel, iron, and copper base alloys will be presented and correlated to microstructure.

  20. Hydrogen embrittlement of metals. A bibliography with abstracts. Search period covered: 1964--August 1975

    International Nuclear Information System (INIS)

    Smith, M.F.

    1975-10-01

    The research covers the hydrogen embrittlement of both ferrous and nonferrous metals and alloys and includes nuclear technology, aircraft metallurgy, mechanical properties, testing, electroplating, fatigue, corrosion and fracture. Contains 230 abstracts

  1. Progress report of the Metallurgy Division for the period 1978-1980

    International Nuclear Information System (INIS)

    Sharma, B.D.; Mohan, Ashok; Bose, D.K.; Rao, C.N.; Chouthai, S.S.

    1980-01-01

    The research and development (R and D) work of the Metallurgy Division of the Bhabha Atomic Research Centre at Bombay for the period 1978-1980 is reported in the form of individual summaries under the headings: extractive metallurgy section, physical metallurgy section, corrosion and electrometallurgy section, ceramics section. Progress of work of beryllium pilot plant project, programme for R-5 utilisation for materials irradiation research project, development of rare, reactive and refractory metals, and development of ceramics materials for MHD programme is surveyed. Lists of publications, deputations, visits, conferences, colloquia are given. A chart at the end shows the various sections of the Division and personnel in each section. (M.G.B.)

  2. Enterprise Architecture beyond the Enterprise

    DEFF Research Database (Denmark)

    Tambo, Torben

    2017-01-01

    of this discipline is the topic of this paper. This paper is taking a point of departure in general theories of business-to-business relationships along with inter-organisational information systems, interoperability and business ecosystems. The general theories are applied to the Extended Enterprise Architecture...... organisational boundaries. A case is presented of an enterprise engaging in technology-based business process integration that in turn is explicated as enterprise architecture initiatives with both more and less powerful partners. This paper underlines the necessity to be able to have EA spanning initiatives......As the most enterprises are relying on relations to other enterprises, it is relevant to consider enterprise architecture for inter-organisational relations particularly those relations involving technology. This has been conceptualised as Extended Enterprise Architecture, and a systematic review...

  3. Annual report of the Metallurgy Division [for the] period ending December 1977

    International Nuclear Information System (INIS)

    Elayaperumal, K.; Sridhar Rao, Ch.; Mukhopadhyay, P.; Rao, S.V.K.

    1979-01-01

    The research and development work carried out and the various programmes underway in the Metallurgy Division of the Bhabha Atomic Research Centre, Bombay, during the calendar year 1977 have been reported. The R and D work and programmes cover extraction metallurgy, physical metallurgy, alloy development, corrosion metallurgy and ceramics. Some of the major studies and programmes are: (1) development of processes for extraction of niobium, vanadium, hafnium and nickel, (2) preparation of niobium alloys, ferro-zirconium, ceramic grade zirconia, (3) electro-refining of zircaloy scrap, (4) preparation of anhydrous beryllium fluoride from Indian beryl, (5) preparation of beryllium alloys, (6) studies on phase transformation and deformation behaviour of zirconium and zirconium-oxygen alloys, (7) self-diffusion studies in dilute Zr-Fe and Zr-Cr alloys, (8) studies on corrosion and stress corrosion cracking of zirconium base alloys and (9) sintering studies on ZrO 2 -PuO 2 and BeO. (M.G.B.)

  4. Powder-Metallurgy Process And Product

    Science.gov (United States)

    Paris, Henry G.

    1988-01-01

    Rapid-solidification processing yields alloys with improved properties. Study undertaken to extend favorable property combinations of I/M 2XXX alloys through recently developed technique of rapid-solidification processing using powder metallurgy(P/M). Rapid-solidification processing involves impingement of molten metal stream onto rapidly-spinning chill block or through gas medium using gas atomization technique.

  5. Summarizing of new techniques in uranium mining and metallurgy

    International Nuclear Information System (INIS)

    Wang Delin; Zhang Fei; Su Yanru; Zeng Yijun; Meng Jin

    2010-01-01

    According to character of national resources and uranium mining and metallurgical science and technology members research achievements, new techniques in ten scientific research area of in-situ leaching, heap leaching, multi-metal comprehensive recovery, bio-metallurgy etc. for 10 years is introduced in this paper. The level of innovation ability is shown by technical index, resources recovery and reduction capital cost etc. datum. The application bound of natural uranium resource is enlarged and production ability of national uranium is increased. It is put forward renovation and development ideas for uranium mining and metallurgy. (authors)

  6. Enterprise Architecture beyond the Enterprise:Extended Enterprise Architecture Revisited

    OpenAIRE

    Tambo, Torben

    2017-01-01

    As the most enterprises are relying on relations to other enterprises, it is relevant to consider enterprise architecture for inter-organisational relations particularly those relations involving technology. This has been conceptualised as Extended Enterprise Architecture, and a systematic review of this discipline is the topic of this paper. This paper is taking a point of departure in general theories of business-to-business relationships along with inter-organisational information systems,...

  7. Extractive metallurgy. Recent advances

    International Nuclear Information System (INIS)

    Stevenson, E.J.

    1977-01-01

    Detailed technical information derived from patents issued since 1975 on extractive metallurgy is presented. In part one, concerning copper, the major areas covered are: smelting and roasting; acid leaching; ammonia leach processes; cuprous chloride and ferric chloride; and recovery of copper values from solution. Part two covers other metals, including: nickel and cobalt; ocean floor nodules; lead, zinc, molybdenum and manganese; precious metals; and uranium titanium, tantalum, rhenium, gallium, and other metals

  8. Metallurgy department publications and lectures 1987

    International Nuclear Information System (INIS)

    Schroeder Pedersen, A.; Bilde-Soerensen, J.B.

    1988-04-01

    A presentation (including abstract) of scientific and technical publications and lectures by the staff of the Metallurgy Department during 1987 is given. The list comprises journal papers, conference papers, reports, lectures and poster presentations in the following categories: Publications, Lectures and Poster Presentations. (author)

  9. Aspects of the magnetism of ferrous chloride

    International Nuclear Information System (INIS)

    Carrara, P.

    1968-01-01

    This work is a critical review of the existing work on ferrous chloride and presents, as well, a number of new experimental results. First, a careful analysis of the level structure of ferrous ions in the crystalline field shows that the crystalline anisotropy is of the same order of magnitude as the exchange interactions, a feature which gives rise to some particular effects, such as an upward curvature of the magnetization curve at 0 K in a perpendicular magnetic field. Further, the very low temperature (T > 0.4 K) thermal variation of both the specific heat and magnetic susceptibility evidences a magnetic component in elementary excitations. This result suggests the presence of a large magneto-elastic coupling. Finally, an experimental study of the H-T phase diagram near T N and of the critical behaviour of the specific heat and parallel susceptibility was performed. (author) [fr

  10. Parent-martensite interface structure in ferrous systems

    International Nuclear Information System (INIS)

    Ma, X.; Pond, R.C.

    2007-01-01

    Recently, a Topological Model of martensitic transformations has been presented wherein the habit plane is a semi-coherent structure, and the transformation mechanism is shown explicitly to be diffusionless. This approach is used here to model martensitic transformations in ferrous alloys. The habit plane comprises coherent (1 1 1) γ parallel (0 1 1) α terraces where the coherency strains are accommodated by a network of dislocations, originating in the martensite phase, and disconnections (transformation dislocations). The disconnections can move conservatively across the interface, thereby effecting the transformation. Since the disconnections exhibit step character, the overall habit plane deviates from the terrace plane. A range of network geometries is predicted corresponding to orientation relationships varying from Nishiyama-Wasserman to Kurdjumov-Sachs. This range of solutions includes habit planes close to {2 9 5}, {5 7 5} and {1 2 1}, in good agreement with experimental observations in various ferrous alloys

  11. Effects of ferrous ions on the reductive dechlorination of trichloroethylene by zero-valent iron

    International Nuclear Information System (INIS)

    Liu, C.-C.; Tseng, D.-H.; Wang, C.-Y.

    2006-01-01

    The surface characteristics of zero-valent iron (ZVI) and the efficiency of reductive dechlorination of trichloroethylene (TCE) in the presence of ferrous ions were studied. The experimental results indicated that the acid-washing of a metallic iron sample enhanced the efficiency of TCE degradation by ZVI. This occurred because acid-washing changed the conformation of oxides on the surface of iron from maghemite (γ-Fe 2 O 3 ) to the more hydrated goethite (α-FeOOH), as was confirmed by XPS analysis. However, when ferrous ions were simultaneous with TCE in water, the TCE degradation rate decreased as the concentration of ferrous ion increased. This was due to the formation of passive precipitates of ferrous hydroxide, including maghemite and magnetite (Fe 3 O 4 ), that coated on the surface of acid-washed ZVI, which as a result inhibited the electron transfer and catalytic hydrogenation mechanisms. On the other hand, in an Fe 0 -TCE system without the acid-washing pretreatment of ZVI, ferrous ions were adsorbed into the maghemite lattice which was then converted to semiconductive magnetite. Thus, the electrons were transferred from the iron surface and passed through the precipitates, allowing for the reductive dechlorination of TCE

  12. A Comparison of the Plastic Flow Response of a Powder Metallurgy Nickel Base Superalloy (Postprint)

    Science.gov (United States)

    2017-04-01

    AFRL-RX-WP-JA-2017-0225 A COMPARISON OF THE PLASTIC-FLOW RESPONSE OF A POWDER- METALLURGY NICKEL-BASE SUPERALLOY (POSTPRINT) S.L...COMPARISON OF THE PLASTIC-FLOW RESPONSE OF A POWDER- METALLURGY NICKEL-BASE SUPERALLOY (POSTPRINT) 5a. CONTRACT NUMBER IN-HOUSE 5b. GRANT...behavior at hot-working temperatures and strain rates of the powder- metallurgy superalloy LSHR was determined under nominally-isothermal and transient

  13. Discussion of the Investigation Method on the Reaction Kinetics of Metallurgical Reaction Engineering

    Science.gov (United States)

    Du, Ruiling; Wu, Keng; Zhang, Jiazhi; Zhao, Yong

    Reaction kinetics of metallurgical physical chemistry which was successfully applied in metallurgy (as ferrous metallurgy, non-ferrous metallurgy) became an important theoretical foundation for subject system of traditional metallurgy. Not only the research methods were very perfect, but also the independent structures and systems of it had been formed. One of the important tasks of metallurgical reaction engineering was the simulation of metallurgical process. And then, the mechanism of reaction process and the conversion time points of different control links should be obtained accurately. Therefore, the research methods and results of reaction kinetics in metallurgical physical chemistry were not very suitable for metallurgical reaction engineering. In order to provide the definite conditions of transmission, reaction kinetics parameters and the conversion time points of different control links for solving the transmission and reaction equations in metallurgical reaction engineering, a new method for researching kinetics mechanisms in metallurgical reaction engineering was proposed, which was named stepwise attempt method. Then the comparison of results between the two methods and the further development of stepwise attempt method were discussed in this paper. As a new research method for reaction kinetics in metallurgical reaction engineering, stepwise attempt method could not only satisfy the development of metallurgical reaction engineering, but also provide necessary guarantees for establishing its independent subject system.

  14. Nuclear science and metallurgy. Advances and interactions

    Energy Technology Data Exchange (ETDEWEB)

    Grison, E [CEA Centre d' Etudes Nucleaires de Saclay, 91 - Gif-sur-Yvette (France)

    1977-01-01

    The history of the production of atomic power by fission since 1953 is reviewed: metallurgy of uranium; the new metals zirconium and beryllium; steels and nuclear structure; nuclear reactor vessels; water corrosion; effects of radiations.

  15. Evaluation of Ferric and Ferrous Iron Therapies in Women with Iron Deficiency Anaemia

    Science.gov (United States)

    Berber, Ilhami; Erkurt, Mehmet Ali; Aydogdu, Ismet; Kuku, Irfan

    2014-01-01

    Introduction. Different ferric and ferrous iron preparations can be used as oral iron supplements. Our aim was to compare the effects of oral ferric and ferrous iron therapies in women with iron deficiency anaemia. Methods. The present study included 104 women diagnosed with iron deficiency anaemia after evaluation. In the evaluations performed to detect the aetiology underlying the iron deficiency anaemia, it was found and treated. After the detection of the iron deficiency anaemia aetiology and treatment of the underlying aetiology, the ferric group consisted of 30 patients treated with oral ferric protein succinylate tablets (2 × 40 mg elemental iron/day), and the second group consisted of 34 patients treated with oral ferrous glycine sulphate tablets (2 × 40 mg elemental iron/day) for three months. In all patients, the following laboratory evaluations were performed before beginning treatment and after treatment. Results. The mean haemoglobin and haematocrit increases were 0.95 g/dL and 2.62% in the ferric group, while they were 2.25 g/dL and 5.91% in the ferrous group, respectively. A significant difference was found between the groups regarding the increase in haemoglobin and haematocrit values (P < 0.05). Conclusion. Data are submitted on the good tolerability, higher efficacy, and lower cost of the ferrous preparation used in our study. PMID:25006339

  16. Nuclear science and metallurgy. Advances and interactions

    International Nuclear Information System (INIS)

    Grison, Emmanuel

    1977-01-01

    The history of the production of atomic power by fission since 1953 is reviewed: metallurgy of uranium; the new metals zirconium and beryllium; steels and nuclear structure; nuclear reactor vessels; water corrosion; effects of radiations [fr

  17. Precipitation in Powder Metallurgy, Nickel Base Superalloys: Review of Modeling Approach and Formulation of Engineering (Postprint)

    Science.gov (United States)

    2016-12-01

    AFRL-RX-WP-JA-2016-0333 PRECIPITATION IN POWDER- METALLURGY , NICKEL-BASE SUPERALLOYS: REVIEW OF MODELING APPROACH AND FORMULATION OF...PRECIPITATION IN POWDER- METALLURGY , NICKEL- BASE SUPERALLOYS: REVIEW OF MODELING APPROACH AND FORMULATION OF ENGINEERING (POSTPRINT) 5a...and kinetic parameters required for the modeling of γ′ precipitation in powder- metallurgy (PM), nickel-base superalloys are summarized. These

  18. The metallurgy, science and engineering

    International Nuclear Information System (INIS)

    Pineau, A.; Quere, Y.

    2011-01-01

    Metallurgy, the science of metals and the technical discipline concerned with the production, shaping and assembling of metals, is one of the major assets of European economy. The French metallurgy industry - from producers (steel, light alloys, ...) to users (car, aviation, nuclear industries, ...) -- has achieved in many of its sectors a world-class level of excellence, based on high-quality research centres that are recognized both for their theoretical and experimental academic work. By contrast, public research is insufficiently concerned with engineering. In 2004, this industry employed 1 800 000 persons, 220 000 of which worked as engineers and managers in 45 000 companies, with a turnover of 420 billion euros. This state of grace is starting to decline. We are undergoing, in this sector as in others, a de-industrialization that affects upstream activities: courses in these disciplines, which have been previously outstanding, have partially disappeared; laboratories have shrunk; expertise has been dispersed; students are staying away from a discipline they consider 'unfruitful', like many other engineering sciences. Simultaneously, further up in this sector, decision centres have moved away from production centres and away from our country. France still maintains a few important R and D centres within international groups in spite of France's decreasing weight in world production. However, these groups see the future of R and D as being centred in the emerging countries (China, India...). The main users (transport, energy, ...) are losing their experts as are the technical centres on which rely a large network of small and medium businesses. The consequences are alarming in view of the already noticeable loss of technical control. This trend can and must be reversed. Because of its presence in many industrial sectors and its excellence, metallurgy - including both research and industry - is an essential activity in which France should remain a major player

  19. Effects of ferrous ions on the reductive dechlorination of trichloroethylene by zero-valent iron

    Energy Technology Data Exchange (ETDEWEB)

    Liu, C.-C. [Graduate Institute of Environmental Engineering, National Central University, Chungli, Taiwan 32001 (China); Tseng, D.-H. [Graduate Institute of Environmental Engineering, National Central University, Chungli, Taiwan 32001 (China)]. E-mail: dhtseng@ncuen.ncu.edu.tw; Wang, C.-Y. [Graduate Institute of Environmental Engineering, National Central University, Chungli, Taiwan 32001 (China)

    2006-08-25

    The surface characteristics of zero-valent iron (ZVI) and the efficiency of reductive dechlorination of trichloroethylene (TCE) in the presence of ferrous ions were studied. The experimental results indicated that the acid-washing of a metallic iron sample enhanced the efficiency of TCE degradation by ZVI. This occurred because acid-washing changed the conformation of oxides on the surface of iron from maghemite ({gamma}-Fe{sub 2}O{sub 3}) to the more hydrated goethite ({alpha}-FeOOH), as was confirmed by XPS analysis. However, when ferrous ions were simultaneous with TCE in water, the TCE degradation rate decreased as the concentration of ferrous ion increased. This was due to the formation of passive precipitates of ferrous hydroxide, including maghemite and magnetite (Fe{sub 3}O{sub 4}), that coated on the surface of acid-washed ZVI, which as a result inhibited the electron transfer and catalytic hydrogenation mechanisms. On the other hand, in an Fe{sup 0}-TCE system without the acid-washing pretreatment of ZVI, ferrous ions were adsorbed into the maghemite lattice which was then converted to semiconductive magnetite. Thus, the electrons were transferred from the iron surface and passed through the precipitates, allowing for the reductive dechlorination of TCE.

  20. Metallurgy for nuclear engineering

    International Nuclear Information System (INIS)

    Kozlov, A.F.

    1986-01-01

    Principal ways of development in metallurgy and metallurgical equipment on nuclear engineering plants are discussed. A great attention is paid to changing welded structures for casted and forged ones. These measures give the possibility to increase reliability of NPP components and decrease labour content. The following processing procedures have been introduced: vacuum carbon reduction providing small amount of nonmetallic inclusions in reactor vessel steel; manufacturing steel large-size castings (360 and 420 t) for WWER vessels; rolling at plate mill 5000 etc

  1. Physical metallurgy of titanium alloys

    International Nuclear Information System (INIS)

    Collings, E.W.

    1988-01-01

    Researches in electric, magnetic, thermophysical properties of titanium alloys in the wide range of temperatures (from helium upto elevated one), as well as stability of phases in alloys of different types are generalized. Fundamental description of physical properties of binary model alloys is given. Acoustic emission, shape memory and Bauschinger effects, pseudoelasticity, aging and other aspects of physical metallurgy of titanium alloys are considered

  2. Uranium mining and metallurgy library information service under the network environment

    International Nuclear Information System (INIS)

    Tang Lilei

    2012-01-01

    This paper analyzes the effect of the network environment on the uranium mining and metallurgy of the information service. Introduces some measures such as strengthening professional characteristic literature resources construction, changing the service mode, building up information navigation, deepening service, meet the individual needs of users, raising librarian's quality, promoting the co-construction and sharing of library information resources, and puts forward the development idea of uranium mining and metallurgy library information service under the network environment. (author)

  3. Powder metallurgy bearings for advanced rocket engines

    Science.gov (United States)

    Fleck, J. N.; Killman, B. J.; Munson, H.E.

    1985-01-01

    Traditional ingot metallurgy was pushed to the limit for many demanding applications including antifriction bearings. New systems require corrosion resistance, better fatigue resistance, and higher toughness. With conventional processing, increasing the alloying level to achieve corrosion resistance results in a decrease in other properties such as toughness. Advanced powder metallurgy affords a viable solution to this problem. During powder manufacture, the individual particle solidifies very rapidly; as a consequence, the primary carbides are very small and uniformly distributed. When properly consolidated, this uniform structure is preserved while generating a fully dense product. Element tests including rolling contact fatigue, hot hardness, wear, fracture toughness, and corrosion resistance are underway on eleven candidate P/M bearing alloys and results are compared with those for wrought 440C steel, the current SSME bearing material. Several materials which offer the promise of a significant improvement in performance were identified.

  4. Development and application of characteristic database for uranium mining and metallurgy in the library of Beijing Research Institute of Chemical Engineering and Metallurgy

    International Nuclear Information System (INIS)

    Gao Renxi

    2012-01-01

    Beijing Research Institute of Chemical Engineering and Metallurgy (BRICEM) is a multi disciplinary comprehensive research institute engaged in uranium mining, engineering design and related material researches. After 53 years of researches and development, BRICEM has accumulated a plenty of valuable data and resources. By analyzing the actual conditions of BRICEM's technological database, this thesis aims to propose the idea of building a characteristic database for uranium mining and metallurgy. It gives an in-depth analysis on content design, development status and problems of database development, in order to come up with solutions to these problems, as well as suggestions on the future development plans of the characteristic database. (author)

  5. Plutonium metallurgy: The materials science challenges bridging condensed-matter physics and chemistry

    Energy Technology Data Exchange (ETDEWEB)

    Schwartz, A.J. [Lawrence Livermore National Laboratory, Livermore, CA 94550 (United States)], E-mail: schwartz6@llnl.gov

    2007-10-11

    Although there exists evidence of metallurgical practices dating back over 6000 years, studies of Pu and Pu alloys have been conducted for barely 60 years. During the time of the Manhattan Project and extending for some time afterward, the priority to produce the metal took precedence over the fundamental understanding of the metallurgical principals. In the past decade or so, there has been a resurgence in the basic metallurgy, condensed-matter physics, and chemistry of Pu and Pu alloys. These communities have made substantial progress, both experimentally and theoretically in many areas; however, many challenges still remain. The intent of this brief overview is to highlight a number important challenges that we face in the metallurgy of Pu including phase transformations and phase stability, aging, and the connection between electronic structure and metallurgy.

  6. Manufacture of good-weldable low oxygen molybdenum by powder metallurgy

    International Nuclear Information System (INIS)

    Hiraoka, Yutaka; Okada, Masatoshi; Akiyama, Takashi; Yamafuchi, Yasuo.

    1984-01-01

    In general most of commercial molybdenum is produced by the powder metallurgy method and is utilized as a superior heat-resisting material in many fields. Moreover, molybdenum is expected to be used as the first-wall components of JT-60 (JAERI Tokamak-60). However, one of major problems on molybdenum, particularly on powder metallurgy molybdenum, is that any sound welded joint is hard to be obtainable. In many cases weld pores are formed on welding and, therefore, ductility of the welded joint is severely degraded. The object of the present work is to get a sound welded joint without any weld pores by reducing impurity levels in the material. The materials were produced by modifying one or several parts in the ordinary manufacturing process of powder metallurgy molybdenum. Oxygen, nitrogen, carbon and other principal metallic impurities were chemically analysed. The above materials were then subjected to electron-beam-welding by using a melt-run technique, and the soundness of the welded joints was examined by optical microscopy. (author)

  7. Neutrons in the field of metallurgy

    International Nuclear Information System (INIS)

    Novion, C. de

    1989-01-01

    Beams of thermal neutrons are now widely used for the study of material structure. Following a summary of the characteristics of the neutron-material interaction, and an outlook on the major uses of neutrons in metallurgy, we present some examples of application. The comparative advantages and drawbacks of neutrons and X-rays are discussed. 14 refs [fr

  8. Development and characterization of Al-Zn alloy by ingot metallurgy and powder metallurgy with improved mechanical properties

    International Nuclear Information System (INIS)

    Waseem, M.; Awais, H.B.; Zauha, M.S.; Tariq, N.H.

    2007-01-01

    Current project focuses on the production of AI-Zn alloy AA7075 used for wide range of applications like Aircraft components, missile and other structural applications. The above alloy was developed by two different routes. One was melting /casting, after which alloy was characterized by microstructural - examination (optical and SEM) and mechanical testing. Other route was the preparation of this alloy by powder metallurgy. This involves preparation of powders, mechanical alloying, compaction, sintering, rolling, solution treatment and aging then analysis. Powders of Aluminum, Zinc and powders of master alloys of AI-Cu, AI-Mg, AI-Mn, and AI-Cr were Mechanical alloyed. Then this powder was compacted by uniaxial press to form pellets. Sintering was carried out at 500 degree C and then hot rolled in Ar atmosphere. After solution and aging treatments samples were characterized. It is observed that there is about 12-21% improvement in mechanical properties such as tensile strength, yield strength, ductility and fracture toughness due to the more fine microstructure and less segregation than ingot metallurgy route. (author)

  9. THE ROLE OF ENTERPRISE PORTALS IN ENTERPRISE INTEGRATION

    Directory of Open Access Journals (Sweden)

    Gianina RIZESCU

    2006-01-01

    Full Text Available Today’s enterprises are moving business systems to the Internet - to connect people, business processes, and people to business processes in enterprise and across enterprise boundaries. The portal brings it all together: business processes, departmental sites, knowledge management resources, enterprise management systems, CRM systems, analytics, email, calendars, external content, transactions,administration, workflow, and more. The goal of this paper is to present the role of the Enterprise Portal in internal and external enterprise integration.

  10. KINETICS OF THE OXIDATION OF FERROUS CHELATES OF EDTA AND HEDTA IN AQUEOUS-SOLUTION

    NARCIS (Netherlands)

    WUBS, HJ; BEENACKERS, AACM

    1993-01-01

    The kinetics of the reaction of oxygen with ferrous chelates of EDTA and HEDTA was studied in a stirred cell reactor under industrial conditions. The temperature was varied from 20 to 60-degrees-C and the concentration of the ferrous chelate ranged from 0 to 100 mol/m3. The initial pH was 7.5. Under

  11. A Novel Process for Joining Ti Alloy and Al Alloy using Two-Stage Sintering Powder Metallurgy

    Science.gov (United States)

    Long, Luping; Liu, Wensheng; Ma, Yunzhu; Wu, Lei; Liu, Chao

    2018-04-01

    The major challenges for conventional diffusion bonding of joining Ti alloy and Al alloy are the undesirable interfacial reaction, low matrixes and joint strength. To avoid the problem in diffusion bonding, a novel two-stage sintering powder metallurgy process is developed. In the present work, the interface characterization and joint performance of the bonds obtained by powder metallurgy bonding are investigated and are compared with the diffusion bonded Ti/Al joints obtained with the same and the optimized process parameters. The results show that no intermetallic compound is visible in the Ti/Al joint obtained by powder metallurgy bonding, while a new layer formed at the joint diffusion bonded with the same parameters. The maximum tensile strength of joint obtained by diffusion bonding is 58 MPa, while a higher tensile strength reaching 111 MPa for a bond made by powder metallurgy bonding. Brittle fractures occur at all the bonds. It is shown that the powder metallurgy bonding of Ti/Al is better than diffusion bonding. The results of this study should benefit the bonding quality.

  12. Application of laser in powder metallurgy

    International Nuclear Information System (INIS)

    Tolochko, N.K.

    1995-01-01

    Modern status of works in the field of laser application in powder metallurgy (powders preparation, sintering, coatings formation, powder materials processing) is considered. The attention is paid to the new promising direction in powder products shape-formation technology - laser layer-by-layer selective powders sintering and bulk sintering of packaged layered profiles produced by laser cutting of powder-based sheet blanks. 67 refs

  13. Conflitos ambientais: uma análise da assimetria de poder entre os atores sociais envolvidos no caso do Mineroduto da Ferrous / Environmental conflict: an analysis of power asymmetry between social actors involved in the case of Ferrous Pipeline

    Directory of Open Access Journals (Sweden)

    Dayane Rouse Neves Sousa

    2015-12-01

    Full Text Available This work intends to present the environmental conflict initiated due to the installation of pipeline Ferrous Ressources S / A, in the micro region of Viçosa-MG, building an analysis of the positioning of the main social actors involved, as well as their respective relations of power. Thepipeline of Ferrous will connect the complex Beam Mine in Congonhas-MG, the port of Ferrous Ressources in Presidente Kennedy-ES in order to export iron ore. To do so, were used as methodological procedures: bibliographical research; document analysis; semi-structured interviews with different actors; and follow-up meetings of the Popular Campaign Against the Water and Pipeline Ferrous, public hearings and demonstrations taken place in the Viçosa. Furthermore, there was monitoring of the pipeline discussion in local newspapers and on blogs. Thus, this study demonstrated that the Ferrous company, which owns high economic and symbolic power, assumes the role of dominating the conflict. On the other hand, those affected and social movements against the construction of the project, are sometimes in the role of dominated, leaving them to articulate strategies of resistance to delay / stop the construction of the pipeline. The state, in turn, assumes different roles in this context, demonstrating thereby weakness in mediation and conflict management established by pipeline Ferrous mainly in the micro region of Viçosa-MG.

  14. Measurement of dynamic wedge angles and beam profiles by means of MRI ferrous sulphate gel dosimetry

    Science.gov (United States)

    Bengtsson, Magnus; Furre, Torbjørn; Rødal, Jan; Skretting, Arne; Olsen, Dag R.

    1996-02-01

    The purpose of this study is to examine the possible value of measuring the dose distribution in dynamic wedge photon beams using ferrous sulphate gel phantoms analysed by MRI. The wedge angles and dose profiles were measured for a field size of and for dynamic wedge angles of , , and using a 15 MV photon beam generated from a Clinac 2100 CD (Varian). The dose profiles obtained from MRI ferrous sulphate gel were in good agreement with the dose measurements performed with a diode detector array. Also, the wedge angles determined from the MRI ferrous sulphate gel agreed well with the values obtained by using film dosimetry and with calculations by use of TMS (treatment planning system) (Helax, Uppsala, Sweden). The study demonstrated that MRI ferrous sulphate gel dosimetry is an adequate tool for measurements of some beam characteristics of dynamic radiation fields.

  15. Near net shape of powder metallurgy rhenium parts

    International Nuclear Information System (INIS)

    Leonhardt, T.; Downs, J.

    2001-01-01

    In this paper, a description of the stages of processing necessary to produce a near-net shape (NNS) powder metallurgy (PM) rhenium component through the use of cold isostatic pressing (CIP) to form a complex shape will be explained. This method was primarily developed for the production of the 440 N and 490 N liquid apogee engine combustion chambers used in satellite positioning systems. The CIP to NNS process has been used in the manufacture and production of other rhenium aerospace components as well. Cold isostatic pressing (CIP) to a near net shape utilizing a one or two-part mandrel greatly reduces the quantity of rhenium required to produce the component, and also significantly reduces the number of secondary machining operations necessary to complete the manufacturing process. Further, the developments in near-net shape powder metallurgy rhenium manufacturing techniques have generated significant savings in the area of both time and budget. Overall, cost declined by as much as 35 % for the quantity of rhenium chambers, and manufacturing time was decreased by 30-40 %. The quantity of rhenium metal powder used to produce a rhenium chamber was reduced by approximately 70 %, with a subsequent reduction of nearly 50 % in secondary machining operation schedules. Thus, it is apparent that the overall savings provided by the production of near-net shape powder metallurgy rhenium components will be more than merely another aspect of any project involving high temperature applications, it will constitute significant benefit. (author)

  16. CORRELATION BETWEEN PUBLIC FUNDING AND NON-FERROUS INDUSTRY. EVIDENCE FROM CEE AND ROMANIA

    Directory of Open Access Journals (Sweden)

    Brîndusa COVACI

    2016-12-01

    Full Text Available The paper aims at presenting important approaches of the influence of the public funding to industry, especially non-ferrous, in the Countries from Eastern Europe (CEE and Romania. Studies presented in the paper show that the industry funding had been sustained by the European Commission in the community area, but particularly in CEE area. The impact of industry funding will never be exactly measured, but important data can be presented in order to foresee the future development of the European industry. Specific for non-ferrous industry, in the article there are presented important items, as turnover, value added cost, exports, production, which are correlated to EU funds absorption in order to measure the efficiency of the public funding for 2007-2013 period (national and EU funds and the welfare of the CEE and Romanian non-ferrous sector.

  17. THE ROLE OF ENTERPRISE PORTALS IN ENTERPRISE INTEGRATION

    OpenAIRE

    Gianina RIZESCU

    2006-01-01

    Today’s enterprises are moving business systems to the Internet - to connect people, business processes, and people to business processes in enterprise and across enterprise boundaries. The portal brings it all together: business processes, departmental sites, knowledge management resources, enterprise management systems, CRM systems, analytics, email, calendars, external content, transactions, administration, workflow, and more. The goal of this paper is to present the role of the Enterprise...

  18. Extractive metallurgy of the beryllium

    International Nuclear Information System (INIS)

    Alonso, Neusa; Capocchi, Jose Deodoro Trani

    1995-01-01

    A bibliographic review is performed on the beryllium extractive metallurgy. The work describes the main type of ores and processes applied to the metallic beryllium production, beryllium oxide production using fluoride, sulfide and direct chlorination. The thermodynamic consideration are made on beryllium reduction processes, discussing the viability of the beryllium oxide and hallide reduction processes. Under the technological viewpoint, the Cu-Be alloys main production processes are discussed, and the main toxicity problems related with beryllium are mentioned

  19. The Effect of Forging Variables on the Supersolvus Heat-Treatment Response of Powder-Metallurgy Nickel-Base Superalloys

    Science.gov (United States)

    2014-12-01

    AFRL-RX-WP-JA-2015-0160 THE EFFECT OF FORGING VARIABLES ON THE SUPERSOLVUS HEAT-TREATMENT RESPONSE OF POWDER - METALLURGY NICKEL-BASE SUPERALLOYS... POWDER - METALLURGY NICKEL- BASE SUPERALLOYS (POSTPRINT) 5a. CONTRACT NUMBER In-house 5b. GRANT NUMBER 5c. PROGRAM ELEMENT NUMBER 62102F 6. AUTHOR...treatment (SSHT) of two powder - metallurgy , gamma–gamma prime superalloys, IN-100 and LSHR, was established. For this purpose, isothermal, hot

  20. Ion implanting ferrous metals to improve corrosion resistance

    International Nuclear Information System (INIS)

    Dearnaley, G.; Goode, P.D.

    1981-01-01

    A process is described for the treatment of a surface of a ferrous article to improve its corrosion resistance, wherein the surface is subjected to ion bombardment at a temperature above one hundred degrees centigrade in an evacuated enclosure which contains a residual quantity of gaseous oxygen. (author)

  1. Fabrication of metal matrix composites by powder metallurgy: A review

    Science.gov (United States)

    Manohar, Guttikonda; Dey, Abhijit; Pandey, K. M.; Maity, S. R.

    2018-04-01

    Now a day's metal matrix components are used in may industries and it finds the applications in many fields so, to make it as better performable materials. So, the need to increase the mechanical properties of the composites is there. As seen from previous studies major problem faced by the MMC's are wetting, interface bonding between reinforcement and matrix material while they are prepared by conventional methods like stir casting, squeeze casting and other techniques which uses liquid molten metals. So many researchers adopt PM to eliminate these defects and to increase the mechanical properties of the composites. Powder metallurgy is one of the better ways to prepare composites and Nano composites. And the major problem faced by the conventional methods are uniform distribution of the reinforcement particles in the matrix alloy, many researchers tried to homogeneously dispersion of reinforcements in matrix but they find it difficult through conventional methods, among all they find ultrasonic dispersion is efficient. This review article is mainly concentrated on importance of powder metallurgy in homogeneous distribution of reinforcement in matrix by ball milling or mechanical milling and how powder metallurgy improves the mechanical properties of the composites.

  2. Industrial powder metallurgy processing for production of high field Nb3Sn

    International Nuclear Information System (INIS)

    Hecker, A.; Gregory, E.; Wong, J.; Thieme, C.L.H.; Foner, S.

    1988-01-01

    Technology transfer is discussed for fabricating Nb 3 Sn(Ti) via powder metallurgy methods from laboratory scale production at MIT to industrial production at Supercon Inc. Industrial production techniques such as hydrostatic extrusion and drawing have produced superconducting wires with promising critical current densities in preliminary field measurements. Initial steps toward process modification and optimization to improve the commercial feasibility of the powder metallurgy process are evaluated. These modifications are aimed at reducing production time and increasing process flexibility

  3. Ice-core evidence of earliest extensive copper metallurgy in the Andes 2700 years ago

    Science.gov (United States)

    Eichler, A.; Gramlich, G.; Kellerhals, T.; Tobler, L.; Rehren, Th.; Schwikowski, M.

    2017-01-01

    The importance of metallurgy for social and economic development is indisputable. Although copper (Cu) was essential for the wealth of pre- and post-colonial societies in the Andes, the onset of extensive Cu metallurgy in South America is still debated. Comprehensive archaeological findings point to first sophisticated Cu metallurgy during the Moche culture ~200-800 AD, whereas peat-bog records from southern South America suggest earliest pollution potentially from Cu smelting as far back as ~2000 BC. Here we present a 6500-years Cu emission history for the Andean Altiplano, based on ice-core records from Illimani glacier in Bolivia, providing the first complete history of large-scale Cu smelting activities in South America. We find earliest anthropogenic Cu pollution during the Early Horizon period ~700-50 BC, and attribute the onset of intensified Cu smelting in South America to the activities of the central Andean Chiripa and Chavin cultures ~2700 years ago. This study provides for the first time substantial evidence for extensive Cu metallurgy already during these early cultures.

  4. Ice-core evidence of earliest extensive copper metallurgy in the Andes 2700 years ago.

    Science.gov (United States)

    Eichler, A; Gramlich, G; Kellerhals, T; Tobler, L; Rehren, Th; Schwikowski, M

    2017-01-31

    The importance of metallurgy for social and economic development is indisputable. Although copper (Cu) was essential for the wealth of pre- and post-colonial societies in the Andes, the onset of extensive Cu metallurgy in South America is still debated. Comprehensive archaeological findings point to first sophisticated Cu metallurgy during the Moche culture ~200-800 AD, whereas peat-bog records from southern South America suggest earliest pollution potentially from Cu smelting as far back as ~2000 BC. Here we present a 6500-years Cu emission history for the Andean Altiplano, based on ice-core records from Illimani glacier in Bolivia, providing the first complete history of large-scale Cu smelting activities in South America. We find earliest anthropogenic Cu pollution during the Early Horizon period ~700-50 BC, and attribute the onset of intensified Cu smelting in South America to the activities of the central Andean Chiripa and Chavin cultures ~2700 years ago. This study provides for the first time substantial evidence for extensive Cu metallurgy already during these early cultures.

  5. Isolation and characterization of ferrous- and sulfur-oxidizing bacteria from Tengchong solfataric region, China.

    Science.gov (United States)

    Jiang, Chengying; Liu, Ying; Liu, Yanyang; Guo, Xu; Liu, Shuang-Jiang

    2009-01-01

    Microbial oxidation and reduction of iron and sulfur are important parts of biogeochemical cycles in acidic environments such as geothermal solfataric regions. Species of Acidithiobacillus and Leptospirillum are the common ferrous-iron and sulfur oxidizers from such environments. This study focused on the Tengchong sofataric region, located in Yunnan Province, Southwest China. Based on cultivation, 9 strains that grow on ferrous-iron and sulfuric compounds were obtained. Analysis of 16S rRNA genes of the 9 strains indicated that they were affiliated to Acidithiobacillus, Alicyclobacillus, Sulfobacillus, Leptospirillum and Acidiphilium. Physiological and phylogenetic studies indicated that two strains (TC-34 and TC-71) might represent two novel members of Alicyclobacillus. Strain TC-34 and TC-71 showed 94.8%-97.1% 16S rRNA gene identities to other species of Alicyclobacillus. Different from the previously described Alicyclobacillus species, strains TC-34 and TC-71 were mesophilic and their cellular fatty acids do not contain omega-cyclic fatty acids. Strain TC-71 was obligately dependent on ferrous-iron for growth. It was concluded that the ferrous-iron oxidizers were diversified and Alicyclobacillus species were proposed to take part in biochemical geocycling of iron in the Tengchong solfataric region.

  6. A novel reverse osmosis membrane by ferrous sulfate assisted controlled oxidation of polyamide layer

    Science.gov (United States)

    Raval, Hiren D.; Raviya, Mayur R.; Gauswami, Maulik V.

    2017-11-01

    With growing desalination capacity, it is very important to evaluate the performance of thin film composite reverse osmosis (TFC RO) membrane in terms of energy consumption for desalination. There is a trade-off between salt rejection and water-flux of TFC RO membrane. This article presents a novel approach of analyzing the effect of mixture of an oxidizing agent sodium hypochlorite and a reducing agent ferrous sulfate on virgin TFC RO membrane. Experiments were carried out by varying the concentrations of both sodium hypochlorite and ferrous sulfate. The negative charge was induced on the membrane due to the treatment of combination of sodium hypochlorite and ferrous sulfate, thereby resulting in higher rejection of negative ions due to repulsive force. Membrane treated with 1000 mg l-1 sodium hypochlorite and 2000 mg l-1 ferrous sulfate showed the best salt rejection i.e. 96.23%. The characterization was carried out to understand the charge on the membrane surface by Zeta potential, morphology of membrane surface by scanning electron microscope (SEM), surface roughness features by atomic force microscope (AFM) and chemical structural changes by nuclear magnetic resonance (NMR) analysis.

  7. Powder-metallurgy preparation of NiTi shape-memory alloy using mechanical alloying and spark-plasma sintering.

    Czech Academy of Sciences Publication Activity Database

    Novák, P.; Moravec, H.; Vojtěch, V.; Knaislová, A.; Školáková, A.; Kubatík, Tomáš František; Kopeček, Jaromír

    2017-01-01

    Roč. 51, č. 1 (2017), s. 141-144 ISSN 1580-2949 R&D Projects: GA ČR(CZ) GA14-03044S Institutional support: RVO:61389021 ; RVO:68378271 Keywords : mechanical alloying * spark plasma sintering * NiTi * shape memory alloy Subject RIV: JG - Metallurgy; JG - Metallurgy (FZU-D) OBOR OECD: Materials engineering ; Materials engineering (FZU-D) Impact factor: 0.436, year: 2016 https://www.researchgate.net/publication/313900224_Powder-metallurgy_preparation_of_NiTi_shape-memory_alloy_using_mechanical_alloying_and_spark-plasma_sintering

  8. A method for the separation of non-ferrous metal containing particles from a particle stream

    NARCIS (Netherlands)

    Van der Weijden, R.D.; Rem, P.C.

    2004-01-01

    The invention relates to a method for the recovery of non-ferrous metal-comprising particles from a particle stream. According to the invention, the particle stream is put onto a conveyor belt in the form of a monolayer such that with the aid of a liquid, at least the non-ferrous metal comprising

  9. The Mechanical Metallurgy of Armour Steels

    Science.gov (United States)

    2016-10-01

    plate hardness in Figure 2(a) are a result of increased resistance to plastic flow in a ductile hole formation failure mechanism. Beyond a certain...their mechanical metallurgy, and ballistic performance is explained, where such performance is primarily determined by material strength, hardness and...high strain rate behaviour. Other important topics such as toughness; the adiabatic shear phenomenon; structural cracking; and dual hardness and

  10. Introduction to powder metallurgy processes for titanium manufacturing; Introduccion al procesado pulvimetalurgico del titanio

    Energy Technology Data Exchange (ETDEWEB)

    Esteban, P. G.; Bolzoni, L.; Ruiz-Navas, E. M.; Gordo, E.

    2011-07-01

    The development of new extraction processes to produce titanium in powder form leads Powder Metallurgy to an advantage position among the manufacturing processes for titanium. The cost reduction of base material, coupled with the economy of the powder metallurgy processes, give titanium industry the chance to diversify its products, which could lead to production volumes able to stabilise the price of the metal. This work reviews some of the Powder Metallurgy techniques for the manufacturing of titanium parts, and describes the two typical approaches for titanium manufacturing: Blending Elemental and Prealloyed Powders. Among others, conventional pressing and sintering are described, which are compared with cold and hot isostatic pressing techniques. Real and potential applications are described. (Author) 71 refs.

  11. Low-Cobalt Powder-Metallurgy Superalloy

    Science.gov (United States)

    Harf, F. H.

    1986-01-01

    Highly-stressed jet-engine parts made with less cobalt. Udimet 700* (or equivalent) is common nickel-based superalloy used in hot sections of jet engines for many years. This alloy, while normally used in wrought condition, also gas-atomized into prealloyed powder-metallurgy (PM) product. Product can be consolidated by hot isostatically pressing (HIPPM condition) and formed into parts such as turbine disk. Such jet-engine disks "see" both high stresses and temperatures to 1,400 degrees F (760 degrees C).

  12. NSF: A "Populist" Pattern in Metallurgy, Materials Research?

    Science.gov (United States)

    Shapley, Deborah

    1975-01-01

    Describes the testimony of a University of Virginia professor of applied science, who charged that the National Science Foundation grants disproportionately small funds to the best university departments in the field of metallurgy and materials, while preferentially funding middle-ranked departments. (MLH)

  13. 78 FR 8202 - Meeting of the Joint ACRS Subcommittees on Thermal Hydraulic Phenomena and Materials, Metallurgy...

    Science.gov (United States)

    2013-02-05

    ... NUCLEAR REGULATORY COMMISSION Advisory Committee on Reactor Safeguards (ACRS) Meeting of the Joint ACRS Subcommittees on Thermal Hydraulic Phenomena and Materials, Metallurgy and Reactor Fuels; Notice of Meeting The Joint ACRS Subcommittees on Thermal Hydraulic Phenomena and Materials, Metallurgy and...

  14. 21. Colloquium on metallurgy. Amorphous alloys and materials

    International Nuclear Information System (INIS)

    1979-01-01

    Twenty-two papers were presented at the 21st colloquium on metallurgy of amorphous alloys and materials. They deal with the applications, the various types, the preparation methods, the structure, the magnetic and thermodynamic properties and the structure defects of the amorphous materials [fr

  15. One step HIP canning of powder metallurgy composites

    Science.gov (United States)

    Juhas, John J. (Inventor)

    1990-01-01

    A single step is relied on in the canning process for hot isostatic pressing (HIP) powder metallurgy composites. The binders are totally removed while the HIP can of compatible refractory metal is sealed at high vacuum and temperature. This eliminates outgassing during hot isostatic pressing.

  16. Powder Metallurgy characteristics and application: state of the art

    International Nuclear Information System (INIS)

    Zaid, A.I.O.

    2005-01-01

    Powder metallurgy process (P/M) is a near-net or net-shape manufacturing process that combines the features of shape making technology of powder compaction with the development of final material and design properties (physical and mechanical) during subsequent densification or consolidation processes, e.g. sintering. It utilizes the metal powder or powders of metal alloys. In this paper, the major historical developments in P/M are reviewed and discussed. The main parameters involved in the process and their effects on the product characteristics are presented and discussed, which include: powders and methods of their production, particle size and shape, compressibility and additives, sintering temperature and time and finishing processes. The advantages and limitations of powder metallurgy are also presented and discussed. Finally, applications and future developments of the process are outlined and discussed. (author)

  17. Doklady neželezné metalurgie ze sklonku 12. století z Brna, Josefské ulice

    Czech Academy of Sciences Publication Activity Database

    Procházka, Rudolf; Hložek, M.; Holubová-Závodná, B.

    2011-01-01

    Roč. 63, č. 1 (2011), s. 65-89 ISSN 0323-1267 R&D Projects: GA ČR GA404/09/1966 Institutional research plan: CEZ:AV0Z80010507 Keywords : early Middle Age * Brno * non-ferrous metallurgy Subject RIV: AC - Archeology, Anthropology, Ethnology

  18. Fabrication by powder metallurgy of the niobium based alloy Nb-1-Zr

    International Nuclear Information System (INIS)

    Marty, M.; Delaunay, C.; Walder, A.

    1989-01-01

    The Nb-1Zr alloy has been produced by the powder metallurgy technique. Production of powders was performed by centrifugal atomization with the rotating electrode process (REP) under an inert atmosphere of argon-helium. Alloy powders were characterized by granulometric spectra, oxygen content and the various types of structures which were found. After consolidation by extrusion, materials were evaluated by tensile test under vacuum at ambient temperature, 750 and 900 0 C and compared with the same alloy elaborated by ingot metallurgy. 8 refs., 9 figs. (Author)

  19. Preliminary analysis about reducing production costs in uranium mining and metallurgy at Fuzhou uranium mine

    International Nuclear Information System (INIS)

    Wu Sanmao

    1999-01-01

    The production costs in uranium ming and metallurgy have been analyzed quantitatively term by term according to present production situation for The Uranium Mining and Metallurgy Corp, which is part of Fuzhou Uranium Mine. The principal factors influencing on the production costs and the main means reducing the production costs have been found

  20. Production of ferrous sulfate from residue from the iron mining

    International Nuclear Information System (INIS)

    Cardoso, K.A; Riella, H.G.; Abreu, E.F.; Carvalho, E.F. Urano de; Durazzo, M.

    2012-01-01

    This paper was developed from a residue obtained by processing iron ore exploited by the mining company Samarco S/A. The residue was characterized and the analyses showed that it contains about 70% of the mineral hematite (Fe 2 O 3 ) and also that some economically important products could be produced. One is the ferrous sulfate that can be used in pharmaceuticals and also that can be used in the treatment of iron deficiency anemia. The iron, in addition to is importance for the industrial production of steel and parts in general, also has great biological importance in all living beings. In order to produce ferrous sulfate from the byproduct in question, it was developed a obtaining route using metallic iron as hematite reductor and sulfuric acid to form the salt. (author)

  1. Powder Metallurgy Fabrication of Molybdenum Accelerator Target Disks

    Energy Technology Data Exchange (ETDEWEB)

    Lowden, Richard Andrew [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Kiggans Jr., James O. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Nunn, Stephen D. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Parten, Randy J. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States)

    2015-07-01

    Powder metallurgy approaches for the fabrication of accelerator target disks are being examined to support the development of Mo-99 production by NorthStar Medical Technologies, LLC. An advantage of powder metallurgy is that very little material is wasted and, at present, dense, quality parts are routinely produced from molybdenum powder. The proposed targets, however, are thin wafers, 29 mm in diameter with a thickness of 0.5 mm, with very stringent dimensional tolerances. Although tooling can be machined to very high tolerance levels, the operations of powder feed, pressing and sintering involve complicated mechanisms, each of which affects green density and shrinkage, and therefore the dimensions and shape of the final product. Combinations of powder morphology, lubricants and pressing technique have been explored to produce target disks with minimal variations in thickness and little or no distortion. In addition, sintering conditions that produce densities for optimum target dissolvability are being determined.

  2. Lithium extractive metallurgy

    International Nuclear Information System (INIS)

    Josa, J.M.; Merino, J.L.

    1985-01-01

    The Nuclear Fusion National Program depends on lithium supplies. Extractive metallurgy development is subordinate to the localization and evaluation of ore resources. Nowadays lithium raw materials usable with present technology consist of pegmatite ore and brine. The Instituto Geologico y Minero Espanol (IGME) found lepidolite, ambligonite and spodrimene in pegmatite ores in different areas of Spain. However, an evaluation of resources has not been made. Different Spanish surface and underground brines are to be sampled and analyzed. If none of these contain significant levels of lithium, the Junta de Energia Nuclear (JEN) will try an agreement with IGME for ENUSA (Empresa Nacional del Uranio, S.A.) to explore pegmatite-ore bodies from different locations. Different work stages, laboratory tests, pilots plants tests and commercial plant, are foreseen, if the deposits are found. (author)

  3. Is Enterprise Education Relevant to Social Enterprise?

    Science.gov (United States)

    Bridge, Simon

    2015-01-01

    Purpose: Both enterprise education and social enterprise have become fashionable but what, if any, should be the connections between them? The purpose of this paper is to explore those connections and to reflect on what relevance the two concepts might have for each other. Design/methodology/approach: Both enterprise education and social…

  4. Scandium: its occurrence, chemistry, physics, metallurgy, biology, and technology

    International Nuclear Information System (INIS)

    Horovitz, C.T.

    1975-01-01

    This book describes the following aspects of scandium: discovery and history, occurrence in nature, geochemistry and mineralogy, chemical, physical and technological properties, fabrication and metallurgy, its biological significance and toxicology, and its uses. (Extensive references for each chapter)

  5. Development of Cu-Be bronzes through powder metallurgy

    International Nuclear Information System (INIS)

    Abbas, M.

    2012-01-01

    Copper and copper alloys are the major group of commercial alloy. One of the important copper bronzes is Copper beryllium. This is unique among all engineering alloys. Copper beryllium alloy possesses the highest strength in all the copper base alloys. Development of copper beryllium alloy with powder metallurgy is challenging problem due to toxicity of beryllium dust. Purpose of this project to find out parameters by which copper beryllium with all unique properties should obtained. For this purpose efforts are put on development of alternative to copper beryllium system like copper-tin and copper-aluminum by powder metallurgy route. Different time of milling with uniaxial pressure of about 200 MPa and different sintering temperature according to phase diagram of alloy, with different soaking time is tried. Problems may occur like decrease in density after sintering, breaking of samples by Rockwell A, B and C indenters arid by hammering. Cold iso-static pressing at 300 MPa and sintering at above 900 degree C is used to develop copper beryllium alloy. As quenched samples are heat treated at 260 degree C, 315 degree C and 370 degree C with different soaking time of 30, 90 and 180 minutes to find out optimum time and temperature parameters. . It is observed that at aging at 260 degree C for 180 minutes, aging at 315 degree C for 180 minutes and aging at 370 degree C for 30 minutes produce optimum result. By observing these pellets by SEM, precipitates appeared in peak-aged alloy and bigger precipitates in over-aged alloy. Copper beryllium alloy developed through powder metallurgy has better prospects than other copper bronzes. (author)

  6. Preparation of Three-Dimensional Graphene Foams Using Powder Metallurgy Templates.

    Science.gov (United States)

    Sha, Junwei; Gao, Caitian; Lee, Seoung-Ki; Li, Yilun; Zhao, Naiqin; Tour, James M

    2016-01-26

    A simple and scalable method which combines traditional powder metallurgy and chemical vapor deposition is developed for the synthesis of mesoporous free-standing 3D graphene foams. The powder metallurgy templates for 3D graphene foams (PMT-GFs) consist of particle-like carbon shells which are connected by multilayered graphene that shows high specific surface area (1080 m(2) g(-1)), good crystallization, good electrical conductivity (13.8 S cm(-1)), and a mechanically robust structure. The PMT-GFs did not break under direct flushing with DI water, and they were able to recover after being compressed. These properties indicate promising applications of PMT-GFs for fields requiring 3D carbon frameworks such as in energy-based electrodes and mechanical dampening.

  7. Uranium 2000 : International symposium on the process metallurgy of uranium

    International Nuclear Information System (INIS)

    Ozberk, E.; Oliver, A.J.

    2000-01-01

    The International Symposium on the Process Metallurgy of Uranium has been organized as the thirtieth annual meeting of the Hydrometallurgy Section of the Metallurgical Society of the Canadian Institute of Mining, Metallurgy and Petroleum (CIM). This meeting is jointly organized with the Canadian Mineral Processors Division of CIM. The proceedings are a collection of papers from fifteen countries covering the latest research, development, industrial practices and regulatory issues in uranium processing, providing a concise description of the state of this industry. Topics include: uranium industry overview; current milling operations; in-situ uranium mines and processing plants; uranium recovery and further processing; uranium leaching; uranium operations effluent water treatment; tailings disposal, water treatment and decommissioning; mine decommissioning; and international regulations and decommissioning. (author)

  8. Enterprise architecture for small and medium enterprise growth

    CSIR Research Space (South Africa)

    Jacobs, D

    2011-05-01

    Full Text Available with the growth of small enterprises into medium enterprises. SMEAG combines the existing growth stage model of Scott and Bruce, the Enterprise Architecture Framework by Hoogervorst, and the EA as Foundation for Business Execution Model by Ross, Weill...

  9. Modern electrochemical processes and technologies in ionic melts

    Directory of Open Access Journals (Sweden)

    Omelchuk A.

    2003-01-01

    Full Text Available An analysis of the known methods for the electrochemical purification of non-ferrous metals in ionic melts is presented. A comparative estimation of the results of the electrochemical purification of non-ferrous metals by different methods has been performed. The main regularities of the electrochemical behavior of non-ferrous metals in conventional and electrode micro-spacing electrolysis are presented. It has been found that when electrolyzing some metals, e. g. bismuth, gallium, there is either no mass exchange between the electrodes, or it occurs under filtration conditions. It has been shown that the electrode micro-spacing processes provide a high quality of non-ferrous metals purification at low specific consumption of electric power and reagents. The use of bipolar electrodes and β-alumina diaphragms hinders the transfer of metallic impurities from the anode to the cathode. The effects revealed were used to develop new processes for the separation of non-ferrous metal alloys in ionic melts; most of them have been put into practice in non-ferrous metallurgy.

  10. Melting decontamination and recycling of radioactive polluted metals from uranium mining and metallurgy

    International Nuclear Information System (INIS)

    Chen Anquan

    2011-01-01

    Melting method is a primary method used for decontamination of radioactive polluted metal from uranium mining and metallurgy. The decontamination mechanism of the method, the way selection and its features are introduced. Taking the ten year's work of CNNC Uranium Mining and Metallurgy Radioactive Polluted Metal Melting Processing Center as example, the effects of processing radioactive polluted metals by smelting method are discussed. The surface pollution levels of radioactive polluted metal from uranium mining and metallurgy decreased from 4-48 Bq/cm 2 before decontamination to 0.004-0.016 Bq/cm 2 after decontamination, and the specific activity of its metal is less than 1 Bq/g, which is below the solution control level proposed by IAEARS-G1.7 'the application of the concepts of exclusion, immunity and solution control'. The metals after decontamination can be recycled by producing tooth plate and bucket teeth of excavator used in mines. (authors)

  11. Evaluation of iron transport from ferrous glycinate liposomes using ...

    African Journals Online (AJOL)

    Background: Iron fortification of foods is currently a strategy employed to fight iron deficiency in countries. Liposomes were assumed to be a potential carrier of iron supplements. Objective: The objective of this study was to investigate the iron transport from ferrous glycinate liposomes, and to estimate the effects of liposomal ...

  12. Part 5: Experimental periods using a ferrous-ferric chloride blend

    African Journals Online (AJOL)

    drinie

    A blend of ferrous chloride and ferric chloride (FeCl2-FeCl3) was simultaneously dosed into an activated sludge system at .... theoretical oxygen demand for this reaction is small, namely 0.15 ...... The role of bacterial extracellular polymers.

  13. Building of effluence and environment monitoring capability of uranium mining and metallurgy in China

    International Nuclear Information System (INIS)

    Li Xianjie; Hu Penghua; Duan Jianchen; Xue Jianxin

    2014-01-01

    The status of effluence and environmental monitoring capability of nine uranium mining and metallurgy corporations in operation in China was investigated and analyzed. The results show that there exist some problems in all corporations such as imperfect monitoring plan, ineligible analyst, aging equipment, insufficient analysis capacity, lack of good detection limit. In order to solve the problems, several steps have been taken by Department of Safety and Environment Protection and Department of Geology and Mining (CNNC) in three years, including establishing three-level monitoring sys- tem, equipping corresponding monitoring instrument, holding three training classes, enhancing the analyst capacity, publishing the model for effluence and environment monitoring capability of uranium mining and metallurgy and carrying out comparison on monitoring of U and Ra in water, which greatly improved effluence and environment monitoring capability of uranium mining and metallurgy. (authors)

  14. General certification procedure of enterprises and interim job enterprises

    CERN Document Server

    Int. At. Energy Agency, Wien

    2002-01-01

    This procedure defines the certification global process of enterprises employing workers of A or B category for nuclear facilities and interim job enterprises proposing workers of A or B category for nuclear facilities. This certification proves the enterprises ability to satisfy the specification ''E'' of the CEFRI and the interim job enterprises to satisfy the specification ''I'' of the CEFRI. (A.L.B.)

  15. [Hygienic evaluation of risk factors on powder metallurgy production].

    Science.gov (United States)

    2011-01-01

    Complex hygienic, clinical, sociologic and epidemiologic studies revealed reliable relationship between work conditions and arterial hypertension, locomotory system disorders, monocytosis in powder metallurgy production workers. Findings are more probable cardiovascular and respiratory diseases, digestive tract diseases due to influence of lifestyle factors.

  16. Carbon tape microsampling for non-destructive analyses of artefacts

    Czech Academy of Sciences Publication Activity Database

    Bartůněk, V.; Varadzin, Ladislav; Zavřel, Jan

    -, - (2017) ISSN 1866-9557 R&D Projects: GA ČR(CZ) GAP405/10/2334 Institutional support: RVO:67985912 Keywords : microsampling * SEM-EDS * conducting SEM carbon tape * non-ferrous metallurgy * moulds * Early Middle Ages Subject RIV: AC - Archeology, Anthropology, Ethnology OBOR OECD: Archaeology Impact factor: 1.844, year: 2016

  17. Analysis of characteristics and radiation safety situation of uranium mining and metallurgy facilities in north area of China

    International Nuclear Information System (INIS)

    Liu Ruilan; Li Jianhui; Wang Xiaoqing; Huang Mingquan

    2014-01-01

    According to the radiation safety management of uranium mining and metallurgy facilities in north area of China, features and radiation safety conditions of uranium mining and metallurgy facilities in north area of China were analyzed based on summarizing the inspection data for 2011-2013. So the main problems of radiation environment security on uranium mine were studied. The relevant management measures and recommendations were put forward, and the basis for environmental radiation safety management decision making of uranium mining and metallurgy facilities in future was provided. (authors)

  18. Possible Association of Ferrous Phosphates and Ferric Sulfates in S-rich Soil on Mars

    Science.gov (United States)

    Mao, J.; Schroeder, C.; Haderlein, S.

    2012-12-01

    NASA Mars Exploration Rover (MER) Spirit explored Gusev Crater to look for signs of ancient aqueous activity, assess past environmental conditions and suitability for life. Spirit excavated light-toned, S-rich soils at several locations. These are likely of hydrothermal, possibly fumarolic origin. At a location dubbed Paso Robles the light-toned soil was also rich in P - a signature from surrounding rock. While S is mainly bound in ferric hydrated sulfates [1], the mineralogy of P is ill-constrained [2]. P is a key element for life and its mineralogy constrains its availability. Ferrous phases observed in Paso Robles Mössbauer spectra may represent olivine and pyroxene from surrounding basaltic soil [1] or ferrous phosphate minerals [3]. Phosphate is well-known to complex and stabilize Fe 2+ against oxidation to Fe 3+ . Schröder et al. [3] proposed a formation pathway of ferrous phosphate/ferric sulfate associations: sulfuric acid reacts with basalt containing apatite, forming CaSO4 and phosphoric acid. The phosphoric and/or excess sulfuric acid reacts with olivine, forming Fe2+-phosphate and sulfate. The phosphate is less soluble and precipitates. Ferrous sulfate remains in solution and is oxidized as pH increases. To verify this pathway, we dissolved Fe2+-chloride and Na-phosphate salts in sulfuric acid inside an anoxic glovebox. The solution was titrated to pH 6 by adding NaOH when a first precipitate formed, which was ferrous phosphate according to Mössbauer spectroscopy (MB). At that point the solution was removed from the glovebox and allowed to evaporate in the presence of atmospheric oxygen, leading to the oxidation of Fe2+. The evaporation rate was controlled by keeping the suspensions at different temperatures; pH was monitored during the evaporation process. The final precipitates were analyzed by MB and X-Ray Fluorescence (XRF), comparable to MER MB and Alpha Particle X-ray Spectrometer instrument datasets, and complementary techniques such as X

  19. Ferrous Iron Oxidation by Thiobacillus ferrooxidans: Inhibition with Benzoic Acid, Sorbic Acid, and Sodium Lauryl Sulfate

    OpenAIRE

    Onysko, Steven J.; Kleinmann, Robert L. P.; Erickson, Patricia M.

    1984-01-01

    Benzoic acid, sorbic acid, and sodium lauryl sulfate at low concentrations (5 to 10 mg/liter) each effectively inhibited bacterial oxidation of ferrous iron in batch cultures of Thiobacillus ferrooxidans. The rate of chemical oxidation of ferrous iron in low-pH, sterile batch reactors was not substantially affected at the tested concentrations (5 to 50 mg/liter) of any of the compounds.

  20. Removal of chlorite by reaction with ferrous iron

    OpenAIRE

    Iatrou, Angela

    1991-01-01

    The use of chlorine dioxide as an oxidant and/or disinfectant for drinking water treatment has been an alternative considered when utilities seek to control trihalomethane concentrations. However, concern regarding residual concentrations of chlorite and chlorate have resulted in limitations on applied chlorine dioxide dosages. This study describes the use of ferrous iron as a possible reducing agent for the elimination of residual chlorite from drinking water.

  1. Advances in Powder Metallurgy Soft Magnetic Composite Materials

    Directory of Open Access Journals (Sweden)

    Bureš R.

    2017-06-01

    Full Text Available Powder metallurgy has grown with the expansion of various industry. Automotive industry had the most strong influence. Today, more than 90% of PM products are used in the transportation industry. Development of new materials such as magnetic materials is expected to meet the new trends of automotive industry, electric and hybrid vehicles.

  2. Review of the physical metallurgy of Alloy 718

    International Nuclear Information System (INIS)

    Keiser, D.D.; Brown, H.L.

    1976-02-01

    The physical metallurgy of Alloy 718 is updated to 1976 on the basis of a survey of post-1967 literature and current experimental data. Composition, microstructures, and mechanical properties are correlated with heat treatment parameters. The current state of understanding of phase stability, strengthening mechanisms, deformation modes, recovery, and recrystallization in this material is described

  3. Metals in Past Societies: A Global Perspective on Indigenous African Metallurgy Shadreck Chirikure

    Energy Technology Data Exchange (ETDEWEB)

    Devanathan, Ram [Pacific Northwest National Lab. (PNNL), Richland, WA (United States)

    2015-10-01

    This slim book (166 pages) shines a spotlight on pre-industrial African metallurgy, its global connections, and anthropological implications. It integrates seemingly disparate disciplines, such as history, geology, ethnography, archeology, and metallurgy, to illustrate the diversity and innovation in metallurgy across Africa and the role of metals in the rise of socio-economic inequalities and political power. The book has 7 chapters and the focus on metals as enablers of human needs and wants is evident in each chapter. The first chapter presents the context of the work and data sources. The second chapter focuses on the origin and development of mining and metallurgy in pre-industrial Africa. Chapter 3 is dedicated to the interaction of nature and culture in the process of mining. Chapter 4 deals with the transformation of the ore into metal by smelting and the sociocultural aspects of this process. Chapter 5 explores the social and cultural roles acquired by metals as a result of fabrication into objects. Chapter 6 examines the social role of metals, trade in metals, cultural contact, proto-globalization, and technology transfer. Finally, Chapter 7 draws lessons for global anthropology from the African experience. The sources of information are adequately cited and the long list of references at the end of each chapter will be a boon to researchers in this field. The author highlights the cultural aspects and social context of the adoption of metallurgy in Africa while drawing parallels between practices in pre-industrial Africa and those in other parts of the world. The book is peppered with delightful vignettes that offer insights into the process of transforming nature into culturally significant objects. For instance, African miners, like their counterparts in Nepal and Latin America, called upon deities, spirits and ancestors to mediate between nature and humans. Women had distinct roles in this process, but there were variations in these roles and in the

  4. Physical metallurgy and physics of solids

    International Nuclear Information System (INIS)

    Friedel, J.

    1997-01-01

    A historical review of the development of fundamental research at the Cea in the field of material science, is presented, beginning with the study of material issues for nuclear applications, such as the growth, the swelling (of uranium and its alloys) and the embrittlement of steels. Other researches led to the introduction of plutonium in uranium oxide, paving the way to MOX fuels, and the study of diffusion in fundamental metallurgy, hot plasticity especially the hexagonal metals) and steady state conditions under irradiation

  5. Ferrous arrowheads and their oil quench hardening: Some early Indian evidence

    Science.gov (United States)

    Dube, R. K.

    2008-05-01

    A wide variety of ferrous arrowheads were in use in ancient India. Several typical chemical analyses of arrowheads found from archaeological excavation carried out at Kaushambi are reported in this paper. The average carbon content of these arrowheads varied from as low as 0.1 wt.% to approximately 0.9 wt.%. Literary evidence for oil quench hardening of ferrous arrowheads, as reported in famous Sanskrit epics—the Rāmāyana and the Mahābhārata—have been discussed in this paper. This type of quench hardening was intentionally adopted as it helped in preventing distortion and formation of quench cracks in arrowheads. The oil quench-hardened arrowheads were rubbed on stones to sharpen them, which also brought about tempering of martensite due to frictional heat.

  6. A review of experiment data processing method for uranium mining and metallurgy in BRICEM

    International Nuclear Information System (INIS)

    Ye Guoqiang; Lu Kehong; Wang Congying

    1997-01-01

    The authors investigates the methods of experiment data processing in Beijing Research Institute of Chemical Engineering and Metallurgy (BRICEM). It turns out that error analysis method is used to process experiment data, single-factor transformation and orthogonal test design method are adopted for arranging test, and regression analysis and mathematical process simulation are applied to process mathematical model for uranium mining and metallurgy. The methods above-mentioned lay a foundation for the utilization of mathematical statistics in our subject

  7. Ferrous Iron Oxidation by Thiobacillus ferrooxidans: Inhibition with Benzoic Acid, Sorbic Acid, and Sodium Lauryl Sulfate

    Science.gov (United States)

    Onysko, Steven J.; Kleinmann, Robert L. P.; Erickson, Patricia M.

    1984-01-01

    Benzoic acid, sorbic acid, and sodium lauryl sulfate at low concentrations (5 to 10 mg/liter) each effectively inhibited bacterial oxidation of ferrous iron in batch cultures of Thiobacillus ferrooxidans. The rate of chemical oxidation of ferrous iron in low-pH, sterile batch reactors was not substantially affected at the tested concentrations (5 to 50 mg/liter) of any of the compounds. PMID:16346592

  8. Oxidative degradation of acid doped polybenzimidazole membranes and fuel cell durability in the presence of ferrous ions

    DEFF Research Database (Denmark)

    Liao, Jianhui; Yang, Jingshuai; Li, Qingfeng

    2013-01-01

    Phosphoric acid doped polybenzimidazole membranes have been explored as proton exchange membranes for high temperature polymer electrolyte membrane fuel cells. Long-term durability of the membrane is of critical concern and has been evaluated by accelerated degradation tests under Fenton conditions...... of the polymer. Fuel cell durability tests with contaminations of ferrous ions did show considerable performance degradation, however, primarily due to the catalyst deterioration rather than the membrane degradation........ In this study effects of phosphoric acid and ferrous ions were investigated by measurements of the weight loss, intrinsic viscosity and size exclusion chromatography (SEC) of the polymer membranes. Ferrous ions resulted in, as expected, catalytic formation of peroxide radicals and hence the accelerated polymer...

  9. Aspects of ecological radiation endocrinology and occupational pathology

    International Nuclear Information System (INIS)

    Ajtbembetov, B.M.

    1997-01-01

    The collection consists of works on radiation endocrinology and occupational pathology in different branches of industry - petroleum, mining, cotton, non-ferrous metallurgy as well as agriculture. Collection is intended for endocrinologists and occupational pathologists, for specialists of labour protection and occupational safety, for doctors examining of industrial and agricultural workers (author)

  10. Mechanical properties of AZ31 alloy processed by a green metallurgy route

    International Nuclear Information System (INIS)

    D'Enrico, F.; Garces, G.; Hofer, M.; Kim, S. K.; Perez, P.; Cabeza, S.; Adeva, P.

    2013-01-01

    Recently it has been proved that molding of defect-free components of various commercial alloys of magnesium can be carried out successfully when small amounts of CaO are added to the melt, making unnecessary the use of SF 6 coverage. In the case of AZ alloys, this process also remarkably improves their mechanical properties not only by the greater cleaning of alloys but also by the formation of CaAl 2 phase. This work, part of the Green project Metallurgy (http://www.green-metallurgy.eu) funded by the European Union (LIFE+2009), studies the influence of different CaO additions on the microstructure and mechanical properties of AZ31 Eco-Mg alloy. The alloy was processed by a conventional route involving extrusion of as-cast rods as well as by a powder metallurgy route (PM) using chips as starting material. The objective was to analyze the viability of recycling machining chips to manufacture components for the automobile industry and transportation in general, because of its low cost and environmental impact. It has been demonstrated that alloys processed from chips exhibit the highest tensile stress values, close to 320 MPa. (Author)

  11. Milling and Drilling Evaluation of Stainless Steel Powder Metallurgy Alloys

    Energy Technology Data Exchange (ETDEWEB)

    Lazarus, L.J.

    2001-12-10

    Near-net-shape components can be made with powder metallurgy (PM) processes. Only secondary operations such as milling and drilling are required to complete these components. In the past and currently production components are made from powder metallurgy (PM) stainless steel alloys. process engineers are unfamiliar with the difference in machining properties of wrought versus PM alloys and have had to make parts to develop the machining parameters. Design engineers are not generally aware that some PM alloy variations can be furnished with machining additives that greatly increase tool life. Specimens from a MANTEC PM alloy property study were made available. This study was undertaken to determine the machining properties of a number of stainless steel wrought and PM alloys under the same conditions so that comparisons of their machining properties could be made and relative tool life determined.

  12. Application of Microscopy and X-ray Diffraction in Optimization of the Production of NiTi Alloy by Powder Metallurgy

    Czech Academy of Sciences Publication Activity Database

    Novák, P.; Školáková, A.; Vojtěch, V.; Knaislová, A.; Pokorný, P.; Moravec, H.; Kopeček, Jaromír; Karlík, M.; Kubatík, Tomáš František

    2014-01-01

    Roč. 14, č. 3 (2014), s. 387-392 ISSN 1213-2489. [Mezinárodní konference „Mikroskopie a nedestruktivní zkoušení materiálů/3./. Litoměřice, 22.10.2014-24.10.2014] R&D Projects: GA ČR(CZ) GA14-03044S Institutional support: RVO:61389021 ; RVO:68378271 Keywords : powder metallurgy * NiTi, * mechanical alloying * reactive sintering Subject RIV: JG - Metallurgy; JG - Metallurgy (FZU-D) http://journal.strojirenskatechnologie.cz/templates/obalky_casopis/XIV_2014-3.pdf

  13. Peculiarities of powder metallurgy of vanadium and its alloys

    International Nuclear Information System (INIS)

    Radomysel'skij, I.D.; Solntsev, V.P.; Evtushenko, O.V.

    1987-01-01

    Literature data on preparation of vanadium powder and powder materials on the vanadium base are generalized. Application of powder metallurgy engineering, allowing simulaneously to introduce practically any strengthening and solid-lubricating components as well as to alloy vanadium, permits undoubtedly to develop composite materials on the vanadium base

  14. Preparation of Magnetite Nanocrystals from Ferrous Sulphate Solution

    International Nuclear Information System (INIS)

    Cho Yu Mon; Tint Tint Kywe; Moe Moe Kyaw

    2010-12-01

    Magnetite (Fe3O4) nanoparticle were prepared by hydrothermal process in two ways, which would be used for production of copier toner.In this investigation, the first process was made from ferrous sulphate (FeSO4 . 7H2O) by using 10 M sodium hydroxide solution. In this method, magnetite nanoparticles were prepared by changing aeration time from 1 to 3 hr and heated at 90C for 15 min. The alternative process was carried out from ferrous sulphate (FeSO4.7H2O) by using 6.6 M sodium hydroxide solution and sodium silicate solution.Magnetite (black iron oxide) was synthesized by using different aeration times and reaction times. Aeration time was changed from 1 to 2 hr and reaction time was changed from 1 to 5.5 hr at 85 C. The magnetites obtained were examined by X-ray Diffraction (XRD) analysis and Scanning Electron Microscopy (SEM) technique. The average particle size range of magnetite nanoprticles were 90-120 nm and 120-150 nm in each process. The maximum yied percentages of magnetite based on FeSO4 in both processing were found to be 46.30% and 60.72%. The precent yields of magnetite in both preparation based on theoretical yields were 91.02% and 94.83% respectively.

  15. New trends for non-ferrous metals in the electrical engineering industry

    International Nuclear Information System (INIS)

    Singer, R.F.

    1989-01-01

    The non-ferrous metals copper, aluminium and nickel are of major importance to the electrical engineering industry. Copper is used for magnet wire, underground cable and overhead contact wire, and aluminium is important for overhead power transmission lines. Nickel alloys are employed as gas turbine blades in power generation. An important new trend in the conductor area is rapid solidification for improved combinations of strength and conductivity. Another new trend is the Conform continuous extrusion process which can decrease cost and increase quality. New high temperature superconductors might change the conductor market completely, but only on the long run. Nickel base blading materials will see considerable improvements from oxide dispersion strengthening and directional solidification. In summary, non-ferrous materials technology for electrical engineering applications is on the move and considerable improvements can be expected within the next decade. (orig.) [de

  16. Metallurgy Department annual progress report for 1987

    International Nuclear Information System (INIS)

    Schroeder Pedersen, A.; Bilde-Soerensen, J.B.; Hansen, N.

    1988-05-01

    Selected activities of the Metallurgy Department at Risoe National Laboratory during 1987 are described. The work is presented in four chapters: Materials Science, Materials Engineering, Materials Technology and Energy Programmes. A survey is given of the Department's participation in international collaboration and of its activities within education and training. Furthermore, the main numbers illustrating the Departments's economy are given. Lists of staff members, visiting scientists, publications, lectures and poster presentations are included. 38 ills. (author)

  17. Proceedings of the 1985 annual powder metallurgy conference

    International Nuclear Information System (INIS)

    Sanderow, H.I.; Giebelhausen, W.L.; Kulkarni, K.M.

    1985-01-01

    This book presents the papers given at a conference on powder metallurgy. Topics considered at the conference included yttrium oxide dispersion strengthened nickel alloy made by mechanical alloying, the optimal design of regression of the additive chromium oxide in aluminium oxide-molybdenum cermets, particle size distribution effects on the sintering of spherical tungsten, and heavy metal alloys containing 30% to 90% tungsten

  18. Enterprise Android programming Android database applications for the enterprise

    CERN Document Server

    Mednieks, Zigurd; Dornin, Laird; Pan, Zane

    2013-01-01

    The definitive guide to building data-driven Android applications for enterprise systems Android devices represent a rapidly growing share of the mobile device market. With the release of Android 4, they are moving beyond consumer applications into corporate/enterprise use. Developers who want to start building data-driven Android applications that integrate with enterprise systems will learn how with this book. In the tradition of Wrox Professional guides, it thoroughly covers sharing and displaying data, transmitting data to enterprise applications, and much more. Shows Android developers w

  19. Metallurgy and purification of semiconductor materials

    International Nuclear Information System (INIS)

    Mughal, G.R.; Ali, M.M.; Ali, I.

    1996-01-01

    In this article the metallurgical aspects of semiconductor science and technology have been stressed here rather than of the physical and electronic aspect of the subject. Semiconductor technology has not merely presented the metallurgist with new challenges. The ease with which the semiconductor planes cleave make possible, the preparation and study of virgin surface. Semiconductor materials were being widely employed in the study of sub-boundaries and structures and can largely contribute to the study of certain aspects of nucleation and growth, precipitation phenomena, mechanical behaviour, in metallurgy. (A.B.)

  20. Mechanism of radiation and thermal decomposition of sulphide non-ferrous metals

    International Nuclear Information System (INIS)

    Mazhrenova, N.P.

    1998-01-01

    This paper deals with the non-ferrous metals sulfides in term of their radiative sensitivity, directed chances of their physical-chemical, and hence technological properties by radiation influence both on sulfide materials and on the processes with their participation. (author)

  1. Reaction mechanisms and evaluation of effective process operation for catalytic oxidation and coagulation by ferrous solution and hydrogen peroxide

    Energy Technology Data Exchange (ETDEWEB)

    Lee, S.H.; Moon, H.J.; Kim, Y.M. [Dept. of Environmental Engineering, Sangmyung Univ., Cheonan (Korea); Bae, W.K. [Dept. of Civil and Environmental Engineering, Hanyang Univ., Ansan, Kyounggi (Korea)

    2003-07-01

    This research was carried out to evaluate the removal efficiencies of COD{sub cr} and colour for the dyeing wastewater by ferrous solution and the different dosage of H{sub 2}O{sub 2} in Fenton process. In the case of H{sub 2}O{sub 2} divided dosage, 7:3 was more effective than 3:7 to remove COD{sub cr} and colour. The results showed that COD was mainly removed by Fenton coagulation, where the ferric ions are formed in the initial step of Fenton reaction. On the other hand colour was removed by Fenton oxidation rather than Fenton coagulation. This paper also aims at pursuing to investigate the effective removal mechanisms using ferrous ion coagulation, ferric ion coagulation and Fenton oxidation process. The removal mechanism of COD{sub cr} and colour was mainly coagulation by ferrous ion, ferric ion and Fenton oxidation. The removal efficiencies were dependent on the ferric ion amount at the beginning of the reaction. However the final removal efficiency of COD and colour was in the order of Fenton oxidation, ferric ion coagulation and ferrous ion coagulation. The reason of the highest removal efficiency by Fenton oxidation can be explained by the chain reactions with ferrous solution, ferric ion and hydrogen peroxide. (orig.)

  2. Enterprise architecture management

    DEFF Research Database (Denmark)

    Rahimi, Fatemeh; Gøtze, John; Møller, Charles

    2017-01-01

    Despite the growing interest in enterprise architecture management, researchers and practitioners lack a shared understanding of its applications in organizations. Building on findings from a literature review and eight case studies, we develop a taxonomy that categorizes applications of enterprise...... architecture management based on three classes of enterprise architecture scope. Organizations may adopt enterprise architecture management to help form, plan, and implement IT strategies; help plan and implement business strategies; or to further complement the business strategy-formation process....... The findings challenge the traditional IT-centric view of enterprise architecture management application and suggest enterprise architecture management as an approach that could support the consistent design and evolution of an organization as a whole....

  3. Enterprise architecture management

    DEFF Research Database (Denmark)

    Rahimi, Fatemeh; Gøtze, John; Møller, Charles

    2017-01-01

    architecture management based on three classes of enterprise architecture scope. Organizations may adopt enterprise architecture management to help form, plan, and implement IT strategies; help plan and implement business strategies; or to further complement the business strategy-formation process......Despite the growing interest in enterprise architecture management, researchers and practitioners lack a shared understanding of its applications in organizations. Building on findings from a literature review and eight case studies, we develop a taxonomy that categorizes applications of enterprise....... The findings challenge the traditional IT-centric view of enterprise architecture management application and suggest enterprise architecture management as an approach that could support the consistent design and evolution of an organization as a whole....

  4. A sustainable process to utilize ferrous sulfate waste from titanium oxide industry by reductive decomposition reaction with pyrite

    International Nuclear Information System (INIS)

    Huang, Penghui; Deng, Shaogang; Zhang, Zhiye; Wang, Xinlong; Chen, Xiaodong; Yang, Xiushan; Yang, Lin

    2015-01-01

    Highlights: • A newly developed treating process of ferrous sulfate was proposed. • The reaction process was discussed by thermodynamic analysis. • Thermodynamic analysis was compared with experiments results. • The kinetic model of the decomposition reaction was determined. • The reaction mechanism of autocatalytic reactions was explored. - Abstract: Ferrous sulfate waste has become a bottleneck in the sustainable development of the titanium dioxide industry in China. In this study, we propose a new method for the reductive decomposition of ferrous sulfate waste using pyrite. Thermodynamics analysis, tubular reactor experiments, and kinetics analysis were performed to analyze the reaction process. The results of the thermodynamic simulation showed that the reaction process and products were different when molar ratio of FeSO_4/FeS_2 was changed. The suitable molar ratio of FeSO_4/FeS_2 was 8–12. The reaction temperature of ferrous sulfate with pyrite was 580–770 K and the main products were Fe_3O_4 and SO_2. The simulation results agreed well with the experimental results. The desulphurization rate reached 98.55% and main solid products were Fe_3O_4 at 823.15 K when mole ratio of FeSO_4/FeS_2 was 8. Nano-sized magnetite was obtained at this condition. The kinetic model was investigated by isoconversional methods. The average E value was 244.34 kJ mol"−"1. The ferrous sulfate decomposition process can be treated as autocatalytic reaction mechanism, which corresponded to the expanded Prout–Tompson (Bna) model. The reaction mechanism of autocatalytic reactions during the process of ferrous sulfate decomposition were explored, the products of Fe oxide substances are the catalyst components.

  5. MULTIFUNCTIONAL CAGULANTS BASED ON HIDROCARBOALUMINATES CALCIUM

    Directory of Open Access Journals (Sweden)

    Ekaterina Viktorovna Siziakova

    2017-03-01

    Full Text Available The article describes harmful factors from the environmental point of view that accompany almost all stages of production of non-ferrous metals. Due to the fact that this industry requires large volume of water, these factors require special attention when cleaning wastewater. The contamination of wastewater by non-ferrous metallurgy is characterized by metal ions, particulate pollutants, acids, SAS, etc, The common feature of all these substances is harmfulness, however, they are often very aggressive and toxic also. The article focuses on the possible use of hidrocarboaluminates calcium as an active ion exchanger for cleanup wastewater metallurgical production.

  6. Iron Metallurgy: Technical Terminology Bulletin. Terminotech, Vol. 2, No. 7.

    Science.gov (United States)

    General Electric Co. of Canada, Ltd., Montreal, Quebec.

    This issue of a bulletin of technological terminology is devoted to iron metallurgy. Various aspects of iron production are described in both French and English. An English-French dictionary of terms comprises the bulk of the document. Explanatory illustrations are appended. (JB)

  7. Quantifying the properties of low-cost powder metallurgy titanium alloys

    International Nuclear Information System (INIS)

    Bolzoni, L.; Ruiz-Navas, E.M.; Gordo, E.

    2017-01-01

    The extensive industrial employment of titanium is hindered by its high production costs where reduction of these costs can be achieved using cheap alloying elements and appropriate alternative processing techniques. In this work the feasibility of the production of low-cost titanium alloys is addressed by adding steel to pure titanium and processing the alloys by powder metallurgy. In particular, a spherical 4140 LCH steel powder commonly used in metal injection moulding is blended with irregular hydride-dehydride Ti. The new low-cost alloys are cold uniaxially pressed and sintered under high vacuum and show comparable properties to other wrought-equivalent and powder metallurgy titanium alloys. Differential thermal analysis and X-ray diffraction analyses confirm that Ti can tolerate the employment of iron as primary alloying element without forming detrimental TiFe-based intermetallic phases. Thus, the newly designed α+β alloys could be used for cheaper non-critical components.

  8. Quantifying the properties of low-cost powder metallurgy titanium alloys

    Energy Technology Data Exchange (ETDEWEB)

    Bolzoni, L., E-mail: bolzoni.leandro@gmail.com [WaiCAM (Waikato Centre for Advanced Materials), The University of Waikato, Private Bag 3105, 3240 Hamilton (New Zealand); Ruiz-Navas, E.M.; Gordo, E. [Department of Materials Science and Engineering, University Carlos III of Madrid, Avda. de la Universidad, 30, 28911 Leganés, Madrid (Spain)

    2017-02-27

    The extensive industrial employment of titanium is hindered by its high production costs where reduction of these costs can be achieved using cheap alloying elements and appropriate alternative processing techniques. In this work the feasibility of the production of low-cost titanium alloys is addressed by adding steel to pure titanium and processing the alloys by powder metallurgy. In particular, a spherical 4140 LCH steel powder commonly used in metal injection moulding is blended with irregular hydride-dehydride Ti. The new low-cost alloys are cold uniaxially pressed and sintered under high vacuum and show comparable properties to other wrought-equivalent and powder metallurgy titanium alloys. Differential thermal analysis and X-ray diffraction analyses confirm that Ti can tolerate the employment of iron as primary alloying element without forming detrimental TiFe-based intermetallic phases. Thus, the newly designed α+β alloys could be used for cheaper non-critical components.

  9. Preparation of magnesium metal matrix composites by powder metallurgy process

    Science.gov (United States)

    Satish, J.; Satish, K. G., Dr.

    2018-02-01

    Magnesium is the lightest metal used as the source for constructional alloys. Today Magnesium based metal matrix composites are widely used in aerospace, structural, oceanic and automobile applications for its light weight, low density(two thirds that of aluminium), good high temperature mechanical properties and good to excellent corrosion resistance. The reason of designing metal matrix composite is to put in the attractive attributes of metals and ceramics to the base metal. In this study magnesium metal matrix hybrid composite are developed by reinforcing pure magnesium with silicon carbide (SiC) and aluminium oxide by method of powder metallurgy. This method is less expensive and very efficient. The Hardness test was performed on the specimens prepared by powder metallurgy method. The results revealed that the micro hardness of composites was increased with the addition of silicon carbide and alumina particles in magnesium metal matrix composites.

  10. Synthesis and characterization of ferrous phosphate (vivianite) and its behavior in aqueous media

    International Nuclear Information System (INIS)

    Diaz F, J.C.

    2003-01-01

    The synthesis and characterization of materials that can be useful in Environmental Chemistry is very important because their characteristics are exposed and its behavior in chemical phenomena as the sorption in aqueous media is understand to use it in the human being benefit. With the object of using, in a future, the octa hydrated ferrous phosphate (vivianite) as a potential candidate for matrix confinement in contention walls for the storage of radioactive waste of long half life, it was synthesized and it characterized physico chemically and their properties of surface of this compound were evaluated. Presently work was carried out the synthesis and structural characterization of the iron phosphate II by infrared spectroscopy with having Fourier transform, high vacuum scanning electron microscopy, X-ray diffraction, thermal gravimetric analysis, the BET multipoint surface area and Moessbauer spectroscopy; as well as, the determination between aqueous media of the isoelectric point and the density of sites of surface of the compound. The octa hydrated ferrous phosphate was obtained pure. The results indicate that the product corresponds to the prospective mineral, the vivianite. The thermal gravimetric analysis demonstrated that the ferrous phosphate is a stable salt after the lost of water. The isoelectric point is since an important parameter because allows to know the behavior of the surface of the material in aqueous systems, in this case the isoelectric point, of the octa hydrated ferrous phosphate, in distilled water is of pH 4.20 and in solution of potassium nitrate 0.5 M is of pH = 3.75. This indicates that the material has an amphoteric surface depending on the pH. On the other hand, the density of active sites of surface obtained by titrations acid-base is of 20 sites by nm 2 . (Author)

  11. Metallurgy Department. Annual progress report for 1988

    International Nuclear Information System (INIS)

    Schroeder Pedersen, A.; Bilde-Soerensen, J.B.; Hansen, N.

    1989-05-01

    Selected activities of the Metallurgy Department at Risoe National Laboratory during 1988 are described. The work is presented in four chapters: Materials Science, Materials Engineering, Materials Technology and Energy Programmes. A survey is given of the Department's participation in international collaboration and of its activities within education and training. Furthermore, the main numbers illustrating the Department's economy are given. Lists of staff members, visiting scientists, publications, lectures and poster presentations are included. (author) 36 ills., 81 refs

  12. Metallurgy Department. Annual progress report for 1989

    International Nuclear Information System (INIS)

    Horsewell, A.; Hansen, N.

    1990-07-01

    Selected activities of the Metallurgy Department at Risoe National Laboratory during 1989 are described. The work is presented in three chapters: Materials Science, Materials Engineering and Materials Technology. A survey is given of the Department's participation in international collaboration and of its acitivities within eduation and training. Furthermore, the main figures outlining the funding and expenditure of the Department are given. Lists of staff members, visiting scientists, publicaltions, lectures and poster presentations are included. (author) 90 refs

  13. Magnetic Resonance Imaging Dosimetry application to chemical ferrous gels

    International Nuclear Information System (INIS)

    Calmet, Ch.

    2000-10-01

    MRI dosimetry is based on the determination of relaxation parameters (T1, T2). Chemical detectors whose NMR properties are sensitive to irradiation are used. Difficulties in absolute relaxation times measure limit the use of this technique. The aim of this work first consists in the development of a quantitative method to determine T, relaxation time on irradiated ferrous gels. So, we can study processes and parameters which affect the technique sensibility. The method sensitivity first depends on imaging instrumentation. Quantitative MRI method used is able to eliminate variable imager factors. The study of instrumental parameters (coil, sequence parameters) permits to define an imaging protocol which is a function of the considered application (volume size, spatial resolution and accuracy). The method sensitivity depends on the detector sensibility too. The best composition of ferrous gel has been determined. Dose distributions are obtained in three minutes. Comparison between MRI results and conventional dosimetry methods (specially ionisation chamber and films) shows a deviation of about 5% for single irradiation with energy fields in the range of 300 keV to 25 MeV. So, the proposed method forms a suitable technique for 3D dosimetry. (author)

  14. Properties of WZ21 (%wt) alloy processed by a powder metallurgy route.

    Science.gov (United States)

    Cabeza, Sandra; Garcés, Gerardo; Pérez, Pablo; Adeva, Paloma

    2015-06-01

    Microstructure, mechanical properties and corrosion behaviour of WZ21 (%wt) alloy prepared by a powder metallurgy route from rapidly solidified powders have been studied. Results were compared to those of the same alloy prepared through a conventional route of casting and extrusion. The microstructure of the extruded ingot consisted of α-Mg grains and Mg3Zn3Y2 (W-phase) and LPSO-phase particles located at grain boundaries. Moreover, stacking faults were also observed within α-Mg grains. The alloy processed by the powder metallurgy route exhibited a more homogeneous and finer microstructure, with a grain size of 2 μm. In this case W-phase and Mg24Y5 phase were identified, but not the LPSO-phase. The microstructural refinement induced by the use of rapidly solidified powders strengthened the alloy at room temperature and promoted superplasticity at higher strain rates. Corrosion behaviour in PBS medium evidenced certain physical barrier effect of the almost continuous arrangements of second phases aligned along the extrusion direction in conventionally processed WZ21 alloy, with a stable tendency around 7 mm/year. On the other hand, powder metallurgy processing promoted significant pitting corrosion, inducing accelerated corrosion rate during prolonged immersion times. Copyright © 2015 Elsevier Ltd. All rights reserved.

  15. A millennium of metallurgy recorded by lake sediments from Morococha, Peruvian Andes.

    Science.gov (United States)

    Cooke, Colin A; Abbott, Mark B; Wolfe, Alexander P; Kittleson, John L

    2007-05-15

    To date, information concerning pre-Colonial metallurgy in South America has largely been limited to the archaeological record of artifacts. Here, we reconstruct a millennium of smelting activity in the Peruvian Andes using the lake-sediment stratigraphy of atmospherically derived metals (Pb, Zn, Cu, Ag, Sb, Bi, and Ti) and lead isotopic ratios (206Pb/ 207Pb) associated with smelting from the Morococha mining region in the central Peruvian Andes. The earliest evidence for metallurgy occurs ca. 1000 A.D., coinciding with the fall of the Wari Empire and decentralization of local populations. Smelting during this interval appears to have been aimed at copper and copper alloys, because of large increases in Zn and Cu relative to Pb. A subsequent switch to silver metallurgy under Inca control (ca. 1450 to conquest, 1533 A.D.) is indicated by increases in Pb, Sb, and Bi, a conclusion supported by further increases of these metals during Colonial mining, which targeted silver extraction. Rapid development of the central Andes during the 20th century raised metal burdens by an order of magnitude above previous levels. Our results represent the first evidence for pre-Colonial smelting in the central Peruvian Andes, and corroborate the sensitivity of lake sediments to pre-Colonial metallurgical activity suggested by earlier findings from Bolivia.

  16. VA Enterprise Design Patters - 2.5 (Enterprise Architecture)

    Data.gov (United States)

    Department of Veterans Affairs — Enterprise architectural guidelines and constraints that provide references to the use of enterprise capabilities that will enable the VA to access and exchange data...

  17. The utilization of mechanochemistry in the extractive metallurgy and at the nanocrystalline materials preparation

    Directory of Open Access Journals (Sweden)

    Boldižárová Eva

    2002-03-01

    Full Text Available The possibility of the application of mechanochemistry in the extractive metallurgy and the nanocrystalline materials preparation is studied. The aim of the experiments is the chloride leaching of a complex sulphidic CuPbZn concentrate (Hodruša-Hámre, the modification of properties of CaCO3 (Yauli, Peru for zinc sorption from model solutions and the mechanochemical reduction of copper sulphide by elemental iron.The chloride leaching of mechanically activated complex sulphidic CuPbZn concentrate is a selective process. While the recoveries of copper, lead and zinc are 65-85 %, the recoveries of silver and gold are less than 7 % and 2 %, respectively.The positive influence of CaCO3 mechanical activation for zinc sorption from ZnSO4 solution was observed. While only 58 % of zinc sorption was determined after 30 minutes for a non-activated sample, 98 % of zinc sorption was determined after 3 minutes sorption for the sample mechanically activated for 15 minutes.By the mechanochemical reduction of copper sulphide with iron, nanocrystalline copper and iron sulphide are formed. This reaction is an example of the new “solid state technology“, where chemical processes in the gaseous and liquid states are excluded.The results can serve as a contribution to the optimization of copper, lead and zinc extraction from complex sulphidic concentrates, the increase of non-ferrous metals sorption efficiency on mineral sorbents as well as to the nanocrystalline copper preparation.The application of mechanical activation has grown in the laboratory research. The Institute of Geotechnics of SAS has also achieved significant theoretical results in study of mechanical activation of sulphides and their reactivity in the different solid-phase reactions with the effect on industrial applications. The Institute has developed the technology of mechanochemical leaching (process MELT which was successfully tested in a pilot plant unit.

  18. Incorporating enterprise strategic plans into enterprise architecture

    NARCIS (Netherlands)

    Lins Borges Azevedo, Carlos

    2017-01-01

    In the last years, information technology (IT) executives have identified IT-business strategic alignment as a top management concern. In the information technology area, emphasis has been given to the Enterprise Architecture (EA) discipline with respect to enterprise management. The focus of the

  19. Prerequisites and opportunities for repositioning of the Urals metallurgy within the Industry 4.0

    Directory of Open Access Journals (Sweden)

    O. A. Romanova

    2017-12-01

    Full Text Available The authors present the modern trends in the development of metallurgy, and classify the technological structure of metallurgical industry. The article contains specific features of the development of metallurgy in the conditions of industry formation. A special role in this process plays the pace of digitalization and robotization of the industry, the development of additive technologies, Internet of things. The authors substantiate the possibility of developing the metallurgy of the Middle Urals as a science-intensive, high-tech complex that meets the requirements of Industry 4.0. This possibility interrelates with its repositioning, one of the main tasks of which is the formation of new sales markets focused on high-tech consumer industries, as well as the preservation of traditional consumption sectors under conditions of increasing competition in the construction materials market. The authors underline the importance of international cooperation in the field of environmentally safe industrial development, with applying the best available technologies and innovative development in general. The authors propose a methodological approach for assessing the repositioning of the regional metallurgical complex. This approach is the consecutive implementation of the following stages: assessment of dynamics and the forecast of development of consumer steel products sector and its structure based on identified priority areas of technological development of metallurgy in the region; construction of a factor model describing the changes in parameters of the RMC repositioning process, and approximation of the characteristics of their nonlinear elements; building a mathematical model on the basis of neural network algorithms for assessing the process of repositioning the RMC, taking into account projected values of the RMK parameters in the process of repositioning and changing the structure of consumer markets for metal products; formation of a variable

  20. Agent-based enterprise integration

    Energy Technology Data Exchange (ETDEWEB)

    N. M. Berry; C. M. Pancerella

    1998-12-01

    The authors are developing and deploying software agents in an enterprise information architecture such that the agents manage enterprise resources and facilitate user interaction with these resources. The enterprise agents are built on top of a robust software architecture for data exchange and tool integration across heterogeneous hardware and software. The resulting distributed multi-agent system serves as a method of enhancing enterprises in the following ways: providing users with knowledge about enterprise resources and applications; accessing the dynamically changing enterprise; locating enterprise applications and services; and improving search capabilities for applications and data. Furthermore, agents can access non-agents (i.e., databases and tools) through the enterprise framework. The ultimate target of the effort is the user; they are attempting to increase user productivity in the enterprise. This paper describes their design and early implementation and discusses the planned future work.

  1. Efficacy, Tolerability, and Acceptability of Iron Hydroxide Polymaltose Complex versus Ferrous Sulfate: A Randomized Trial in Pediatric Patients with Iron Deficiency Anemia

    Directory of Open Access Journals (Sweden)

    Beril Yasa

    2011-01-01

    Full Text Available Iron polymaltose complex (IPC offers similar efficacy with superior tolerability to ferrous sulfate in adults, but randomized trials in children are rare. In a prospective, open-label, 4-month study, 103 children aged >6 months with iron deficiency anemia (IDA were randomized to IPC once daily or ferrous sulfate twice daily, (both 5 mg iron/kg/day. Mean increases in Hb to months 1 and 4 with IPC were 1.2±0.9 g/dL and 2.3±1.3 g/dL, respectively, (both P=0.001 versus baseline and 1.8±1.7 g/dL and 3.0±2.3 g/dL with ferrous sulfate (both P=0.001 versus baseline (n.s. between groups. Gastrointestinal adverse events occurred in 26.9% and 50.9% of IPC and ferrous sulfate patients, respectively (P=0.012. Mean acceptability score at month 4 was superior with IPC versus ferrous sulfate (1.63±0.56 versus 2.14±0.75, P=0.001. Efficacy was comparable with IPC and ferrous sulfate over a four-month period in children with IDA, but IPC was associated with fewer gastrointestinal adverse events and better treatment acceptability.

  2. Empowerment Zones and Enterprise Districts - MDC_EnterpriseZone

    Data.gov (United States)

    NSGIC Local Govt | GIS Inventory — Polygon feature class of Miami Dade County Enterprise Zones. Enterprise Zones are special areas in the county where certain incentives from the State are available...

  3. The most essential tendencies in development of powder metallurgy

    International Nuclear Information System (INIS)

    Fedorchenko, I.M.

    1989-01-01

    A progress in the sphere of creation and application of new types of powder materials is characterized. The materials are as follows: structural, tribotechnical, composite, reinforced, precipitation-hardened, refractory, tool, materials based on light metals and others. A number of important problems whose solution will promote a further development of powder metallurgy are formulated

  4. Evaluation of powder metallurgy superalloy disk materials

    Science.gov (United States)

    Evans, D. J.

    1975-01-01

    A program was conducted to develop nickel-base superalloy disk material using prealloyed powder metallurgy techniques. The program included fabrication of test specimens and subscale turbine disks from four different prealloyed powders (NASA-TRW-VIA, AF2-1DA, Mar-M-432 and MERL 80). Based on evaluation of these specimens and disks, two alloys (AF2-1DA and Mar-M-432) were selected for scale-up evaluation. Using fabricating experience gained in the subscale turbine disk effort, test specimens and full scale turbine disks were formed from the selected alloys. These specimens and disks were then subjected to a rigorous test program to evaluate their physical properties and determine their suitability for use in advanced performance turbine engines. A major objective of the program was to develop processes which would yield alloy properties that would be repeatable in producing jet engine disks from the same powder metallurgy alloys. The feasibility of manufacturing full scale gas turbine engine disks by thermomechanical processing of pre-alloyed metal powders was demonstrated. AF2-1DA was shown to possess tensile and creep-rupture properties in excess of those of Astroloy, one of the highest temperature capability disk alloys now in production. It was determined that metallographic evaluation after post-HIP elevated temperature exposure should be used to verify the effectiveness of consolidation of hot isostatically pressed billets.

  5. Stabilization of Pb and As in soils by applying combined treatment with phosphates and ferrous iron.

    Science.gov (United States)

    Xenidis, Anthimos; Stouraiti, Christina; Papassiopi, Nymphodora

    2010-05-15

    The chemical immobilization of Pb and As in contaminated soil from Lavrion, Greece, using monocalcium phosphate and ferrous sulfate as stabilizing agents was investigated. Monocalcium phosphate was added to contaminated soil at PO(4) to Pb molar ratios equal to 0, 0.5, 1, 1.5 and 2.5, whereas ferrous sulfate was added at Fe to As molar ratios equal to 0, 2.5, 5, 10 and 20. Phosphates addition to contaminated soil decreased Pb leachability, but resulted in significant mobilization of As. Simultaneous immobilization of Pb and As was obtained only when soil was treated with mixtures of phosphates and ferrous sulfate. Arsenic uptake by plants was also seen to increase when soil was treated only with phosphates, but co-addition of ferrous sulfate was efficient in maintaining As phytoaccumulation at low levels. The addition of at least 1.5M/M phosphates and 10M/M iron sulfate to soil reduced the dissolved levels of Pb and As in the water extracts to values in compliance with the EU drinking water standards. However, both additives contributed in the acidification of soil, decreasing pH from 7.8 to values as low as 5.6 and induced the mobilization of pH sensitive elements, such as Zn and Cd. Copyright (c) 2010 Elsevier B.V. All rights reserved.

  6. The metallurgy of alloy 800

    International Nuclear Information System (INIS)

    Stone, P.G.; Orr, J.; Guest, J.C.

    1975-01-01

    Following a review of published information on the metallurgy of the iron/chromium/nickel system, attention is directed to the metallurgical significance of relatively minor compositional variations introduced in Alloy 800 to meet the stress corrosion requirements of the nuclear power industry. These include the effect of carbon, nitrogen, titanium, and aluminium restrictions in the context of Light Water Reactor, High Temperature Reactor, and Fast Reactor applications. Solubility effects are also considered in relation to heat treatment procedures, metallurgical phenomena, and associated properties. The aging behaviour is also discussed and related to fabrication and service performance; particularly stress rupture behaviour. The effect of strain at ambient and elevated temperatures on these aspects is indicated. (author)

  7. Prospects for Ukrainian ferrous metals in the post-soviet period

    Science.gov (United States)

    Levine, R.M.; Bond, A.R.

    1998-01-01

    Two specialists on the mineral industries of the countries of the former USSR survey current problems confronting producers of ferrous metals in Ukraine and future prospects for domestic production and exports. A series of observations documenting the importance of ferrous metals production to Ukraine's economy is followed by sections describing investment plans and needs in the sector, and the role played by Ukraine within the iron and steel industry of the Soviet Union. The focus then turns to assessment of the current regional and global competitive position of Ukrainian producers for each of the major commodities of the sector-iron ore, manganese ore, ferroalloys, steel, and the products of the machine manufacturing and metal working industries. In conclusion, the paper discusses a potential regional industrial integration strategy analogous to that employed in the United States' Great Lakes/Midwest region, which possesses similar types of iron ore deposits and similar transport cost advantages and metallurgical and manufacturing industries. Journal of Economic Literature, Classification Numbers: F14, L61, L72. 1 table, 26 references.

  8. Sustainable Enterprise Excellence

    DEFF Research Database (Denmark)

    Edgeman, Rick; Williams, Joseph; Eskildsen, Jacob Kjær

    , supply chain, customer-related, human capital, financial, marketplace, societal, and environmental performance. Sustainable Enterprise Excellence integrates ethical, efficient and effective (E3) enterprise governance with 3E (equity, ecology, economy) Triple Top Line strategy throughout enterprise...

  9. Chemical and Metallurgy Research (CMR) Sample Tracking System Design Document

    International Nuclear Information System (INIS)

    Bargelski, C. J.; Berrett, D. E.

    1998-01-01

    The purpose of this document is to describe the system architecture of the Chemical and Metallurgy Research (CMR) Sample Tracking System at Los Alamos National Laboratory. During the course of the document observations are made concerning the objectives, constraints and limitations, technical approaches, and the technical deliverables

  10. Influence of thermo-mechanical processing on the microstructure of Cu-based shape memory alloys produced by powder metallurgy

    International Nuclear Information System (INIS)

    Rodriguez, P.P.; Ibarra, A.; Iza-Mendia, A.; Recarte, V.; Perez-Landazabal, J.I.; San Juan, J.; No, M.L.

    2003-01-01

    Cu-Al-Ni shape memory alloys processed by powder metallurgy show very good thermo-mechanical properties, much better than those found in alloys produced by conventional casting. In this paper, we present the microstructural characterisation of these powder metallurgy alloys in order to find the microscopic mechanisms, linked to the powder metallurgy processing method, which are indeed responsible of such good thermo-mechanical behaviour. Electron microscopy studies [scanning electron microscopy (SEM), electron backscatter diffraction (EBSD) and transmission electron microscopy (TEM)] show that powder metallurgy processing creates a sub-grain structure characterised by the presence of low angle sub-boundaries. These sub-boundaries are found to be lying on {1 1 0} and {1 1 2} lattice planes and are composed by an arrangement of superdislocations. These sub-boundaries may improve ductility in two ways: acting as a sink of dislocations which promotes plastic deformation and decreasing stress concentration at grain boundaries. Moreover, since sub-boundaries act as weak obstacles for the movement of martensite plates, the improvement on ductility is accomplished by an adequate thermo-mechanical behaviour

  11. Powder metallurgy and fabricating processes of cermet and metmet fuel in Russia

    International Nuclear Information System (INIS)

    Vatulin, A.; Konovalov, I.; Savchenco, A.; Stetsky, Y.; Trifonov, Y.; Bochvar, A.A.

    2000-01-01

    Methods of powder metallurgy are widely used for manufacturing of various components of reactor core: beryllium reflectors, absorbers, parts of controlling and safety systems, fuel pellets for fuel elements of power reactors and etc. The new problems arising before atomic engineering associated with increasing requirements to safe operation of reactors, non-proliferation of the nuclear weapons and utilization of plutonium stockpile in the world, served as a push to development of new kinds of dispersion nuclear fuel CERMET, CERCER, METMET. The bases of fabricating processes of such compositions are the methods of powder metallurgy. In this report some results of research activities on the development of new kinds of CERMET and METMET fuel and fuel elements for different type reactors are presented. (author)

  12. Enterprise Social Networks

    DEFF Research Database (Denmark)

    Winkler, Till J.; Trier, Matthias

    2017-01-01

    Enterprise Social Networks (ESNs), d. h. Informationssysteme, die die Vernetzung von Mitarbeitern in Unternehmen fördern sollen, sind in verschiedenen Varianten und unter verschiedenen Bezeichnungen (etwa Enterprise Social Media, Corporate Social Software, Social Business oder Enterprise 2...

  13. Sorption of ferrous iron by EPS from the acidophilic bacterium Acidiphilium Sp.: A mechanism proposal

    Energy Technology Data Exchange (ETDEWEB)

    Tapia, J.M.; MuNoz, J.; Gonzlez, F.; Blazquez, M.L.; Ballester, A.

    2016-07-01

    The aim of this work was to assess the uptake of Fe(II) by extracellular polymeric substances (EPS) from the acidophilic bacterium Acidiphillium 3.2Sup(5). These EPS were extracted using EDTA. EPS of A. 3.2Sup(5) loaded in sorption tests with Fe(II), were characterized using the following experimental techniques: scanning electron microscopy (SEM) with energy dispersive X-ray microanalysis (EDX), X-ray diffraction (XRD) and Fourier transform infrared spectroscopy (FTIR). The experimental results indicate that EPS adsorb ferrous iron according to Freundlich model with a metal sorption uptake of K = 1.14 mg1−1/n L1/n g−1 and a sorption intensity of 1/n = 1.26. In addition, ferrous iron sorption by EPS took place by preferential interaction with the carboxyl group which promotes the formation of ferrous iron oxalates (FeC2O4). Since the interaction reaction was reversible (Log K = 0.77 ± 0.33), that means that the cation sorption can be reversed at convenience. (Author)

  14. Algebra for Enterprise Ontology: towards analysis and synthesis of enterprise models

    Science.gov (United States)

    Suga, Tetsuya; Iijima, Junichi

    2018-03-01

    Enterprise modeling methodologies have made enterprises more likely to be the object of systems engineering rather than craftsmanship. However, the current state of research in enterprise modeling methodologies lacks investigations of the mathematical background embedded in these methodologies. Abstract algebra, a broad subfield of mathematics, and the study of algebraic structures may provide interesting implications in both theory and practice. Therefore, this research gives an empirical challenge to establish an algebraic structure for one aspect model proposed in Design & Engineering Methodology for Organizations (DEMO), which is a major enterprise modeling methodology in the spotlight as a modeling principle to capture the skeleton of enterprises for developing enterprise information systems. The results show that the aspect model behaves well in the sense of algebraic operations and indeed constructs a Boolean algebra. This article also discusses comparisons with other modeling languages and suggests future work.

  15. Borax as a lubricant in powder metallurgy

    Directory of Open Access Journals (Sweden)

    Héctor Geovanny Ariza-Suarez

    2014-12-01

    were compacted at 700 MPa in a uniaxial press of 15 tons. DSC-TGA analysis of the mixture with borax was realized. The specimens were sintered in a plasma reactor at 1000 for 30 minutes, with a combined atmosphere of hydrogen and argon. Microhardness and density of the sintered samples was haracterized. XRD analysis was realized to detect possible compounds formation by interaction of borax. This paper shows that borax can be used as a lubricant in powder metallurgy.

  16. Lightweight enterprise architectures

    CERN Document Server

    Theuerkorn, Fenix

    2004-01-01

    STATE OF ARCHITECTUREArchitectural ChaosRelation of Technology and Architecture The Many Faces of Architecture The Scope of Enterprise Architecture The Need for Enterprise ArchitectureThe History of Architecture The Current Environment Standardization Barriers The Need for Lightweight Architecture in the EnterpriseThe Cost of TechnologyThe Benefits of Enterprise Architecture The Domains of Architecture The Gap between Business and ITWhere Does LEA Fit? LEA's FrameworkFrameworks, Methodologies, and Approaches The Framework of LEATypes of Methodologies Types of ApproachesActual System Environmen

  17. Thermal stability and creep behaviour of MgNiYCe-rich mischmetal alloys processed by a powder metallurgy route

    Czech Academy of Sciences Publication Activity Database

    Peréz, P.; Milička, Karel; Badia, J. M.; Garcés, G.; Antoranz, J. M.; Gonzáles, S.; Dobeš, Ferdinand; Adeva, P.

    289-292, - (2009), s. 127-136 ISSN 1012-0386. [DIMAT 2008, International Conference on Diffusion in Materials /7./. Lanzarote, Canary Islands, 28.10.2008-31.10.2008] Grant - others:Ministerio de Ciencia y Tecnologia (ES) MAT2006-11731-C02 Institutional research plan: CEZ:AV0Z20410507 Keywords : magnesium alloys * powder metallurgy * microstructure * thermal stability * creep Subject RIV: JG - Metallurgy

  18. Enterprise architecture, a blueprint for enterprise logistics rollout

    CSIR Research Space (South Africa)

    Coetzee, J

    2013-08-01

    Full Text Available In this paper it is proposed that Enterprise architecture in principle develops the Logistic Support model for systems on System Hierarchical Level 6 and higher. The Enterprise architectural model is a blue print, like the DNA for biological systems...

  19. Indexation Rules for Metallurgy in PASCAL. Original Title: Regles d'Indexation de la Metallurgie'--Technical Note Issued by Informascience--January 1980. Translated by Marie Wallin.

    Science.gov (United States)

    Royal Inst. of Tech., Stockholm (Sweden). Library.

    The indexing rules presented are designed for use with a new French-German database on metallurgy being developed under an agreement by CNRS (Centre National de la Recherche Scientifique, Paris) and BAM (Bundesanstalt fur Materialprufung, Berlin). The new database, which will feature multilingual titles and index terms (French-German-English-) and…

  20. Mathematical model of the oxidation of ferrous iron by a biofilm of Thiobacillus ferrooxidans.

    Science.gov (United States)

    Mesa, M M; Macías, M; Cantero, D

    2002-01-01

    Microbial oxidation of ferrous iron may be a viable alternative method of producing ferric sulfate, which is a reagent used for removal of H(2)S from biogas. The paper introduces a kinetic study of the biological oxidation of ferrous iron by Thiobacillus ferrooxidans immobilized on biomass support particles (BSP) composed of polyurethane foam. On the basis of the data obtained, a mathematical model for the bioreactor was subsequently developed. In the model described here, the microorganisms adhere by reversible physical adsorption to the ferric precipitates that are formed on the BSP. The model can also be considered as an expression for the erosion of microorganisms immobilized due to the agitation of the medium by aeration.

  1. Powder Metallurgy Preparation of Co-Based Alloys for Biomedical Applications

    Czech Academy of Sciences Publication Activity Database

    Marek, I.; Novák, P.; Mlynár, J.; Vojtěch, D.; Kubatík, Tomáš František; Málek, J.

    2015-01-01

    Roč. 128, č. 4 (2015), s. 597-601 ISSN 0587-4246. [International Symposium on Physics of Materials (ISPMA) /13./. Prague, 31.08.2014-04.09.2014] Institutional support: RVO:61389021 Keywords : powder metallurgy * mechanical properties * biomedical applications Subject RIV: JK - Corrosion ; Surface Treatment of Materials Impact factor: 0.525, year: 2015

  2. Oral iron therapy in human subjects, comparative absorption between ferrous salts and iron polymaltose

    International Nuclear Information System (INIS)

    Jacobs, P.; Johnson, G.; Wood, L.

    1984-01-01

    Iron absorption was directly compared between equivalent doses of ferrous salts and a polymaltose complex using a twin-isotope technique in which each individual acts as his own control. In the first study, bioavailability of iron from ferrous sulfate and the complex was defined at physiologic doses of 5 mg (Group 1: n = 14) and therapeutic doses of 50 mg (Group 2: n = 13). In Group 1, mean absorption from salt was 47.77% (SD 14.58%) and from polymaltose, 46.56% SD 17.07%). In Group 2, mean absorption from salt was 32.92% (SD 13.42%) and from polymaltose, 27.07% (SD 6.50%). In a second study, 100 mg of iron in a chewable formulation was used to compare absorption between equal doses of ferrous fumarate and the polymaltose complex. Mean absorption from salt was 10.25% (SD 6.89%) and from polymaltose 10.68% (SD 4.68%). At all three dosage levels, iron is equally available from salt or polymaltose for hemoglobin synthesis (p greater than 0.20), and absorption negatively correlated with plasma ferritin (p less than 0.01). These two materials may be used interchangeably in the treatment of patients with absolute iron deficiency

  3. The mysterious world of plutonium metallurgy: Past and future

    International Nuclear Information System (INIS)

    Hecker, S.S.; Hammel, E.F.

    1998-01-01

    The first atomic bomb detonated at the Trinity Site in New Mexico on July 16, 1945, used plutonium, a man-made element discovered < 5 yr earlier. The story of how Manhattan Project scientists and engineers tackled the mysteries of this element and fabricated it into the first atomic bomb is one of the most fascinating in the history of metallurgy and materials. The authors are currently trying to generate renewed interest in plutonium metallurgy because of the challenge posed by President Clinton, i.e., to keep the nuclear stockpile of weapons safe and reliable without nuclear testing. The stockpile stewardship challenge requires either a lifetime extension of the plutonium components or a remanufacture--neither of which can be verified by testing. In turn, this requires that one achieve a better fundamental understanding of plutonium. Of special interest is the effect of self-irradiation on the properties and on the long-term stability of plutonium and its alloys. Additional challenges arise from long-term concerns about disposing of plutonium and dealing with its environmental legacy. It is imperative to interest the next generation of students in these plutonium challenges

  4. Enterprise architecture for business success

    CERN Document Server

    Wijegunaratne, Inji; Evans-Greenwood, Peter

    2014-01-01

    Enterprise Architecture (EA) has evolved to become a prominent presence in today's information systems and technology landscape. The EA discipline is rich in frameworks, methodologies, and the like. However, the question of 'value' for business ;professionals remains largely unanswered - that is, how best can Enterprise Architecture and Enterprise Architects deliver value to the enterprise? Enterprise Architecture for Business Success answers this question. Enterprise Architecture for Business Success is primarily intended for IT professionals working in the area of Enterprise Architectu

  5. Influence of process variables on biooxidation of ferrous sulfate by an indigenous Acidithiobacillus ferrooxidans. Part I: Flask experiments

    Energy Technology Data Exchange (ETDEWEB)

    S.M. Mousavi; S. Yaghmaei; F. Salimi; A. Jafari [Sharif University of Technology, Tehran (Iran). Department of Chemical and Petroleum Engineering

    2006-12-15

    Biological oxidation of ferrous sulfate by Acidithiobacillus ferrooxidans has proved to be a significant step in the bioleaching of sulfide minerals and the treatment of acid mine drainage. The same bioreaction also has beneficial applications in the desulphurization of coal and removal of hydrogen sulfide from gaseous effluents. In this research, the effects of some process variables such as pH, temperature, elemental sulfur, amount of initial ferrous and magnesium ions on oxidation of ferrous sulfate by a native A. ferrooxidans, which was isolated from a chalcopyrite concentrate, were investigated. All experiments carried out in shake flasks at 33{sup o}C that was obtained as optimum temperature for the specific bacterial growth rate. The optimum range of pH for the maximum growth of the cells and effective biooxidation of ferrous sulfate varied from 2 to 2.3. The maximum biooxidation rate was achieved 1.2 g/L h in a culture initially containing 20.2 g/L Fe{sup 2+}. Mg{sup 2+} from 20 mg/L to 120 mg/L did not have any effect on the efficiency of the process, while the presence of elemental sulfur had negative effect on the biooxidation. 16 refs., 8 figs.

  6. COMPARATIVE STUDY OF EFFICACY OF FERROUS SULPHATE AND CARBONYL IRON IN ANEMIA OF ANTENATAL WOMEN

    Directory of Open Access Journals (Sweden)

    Radhika

    2015-03-01

    Full Text Available Iron deficiency anemia is the most common and important public health problem all over the world in the risk group of antenatal women. Research is going on to improve the iron status of the pregnant women with different forms of iron available. In this regard, Carbonyl Iron is showing promising results in improving the red cell mass with better compliance. 120 antenatal women were recruited in this study. The study comprised of 6weeks for each patient. They were given Carbonyl Iron 100 mg/day and FeS04 100gm/day . Before and after treatment all the baseline and specific investigations were one. Results were tabulated, comparison and significance were tested by unpaired student ’s’ test and their 'p' value was calculated. Results were shown graphically also. Carbonyl Iron showed improvement in hemoglobin, PCV and better than ferrous Sulphate (P <0.001. Incidence of side effects were less with Carbonyl Iron than Ferrous Sulphate, better compliance was seen with Carbonyl Iron. In conclusion, the present study s howed that Carbonyl Iron had better efficacy and safety in the management of Iron deficiency anemia in antenatal women than ferrous Sulphate

  7. Powder-metallurgy superalloy strengthened by a secondary gamma phase.

    Science.gov (United States)

    Kotval, P. S.

    1971-01-01

    Description of experiments in which prealloyed powders of superalloy compositions were consolidated by extrusion after the strengthening by precipitation of a body-centered tetragonal gamma secondary Ni3 Ta phase. Thin foil electron microscopy showed that the mechanical properties of the resultant powder-metallurgy product were correlated with its microstructure. The product exhibited high strength at 1200 F without loss of ductility, after thermomechanical treatment and aging.

  8. Microstructure and Aging of Powder-Metallurgy Al Alloys

    Science.gov (United States)

    Blackburn, L. B.

    1987-01-01

    Report describes experimental study of thermal responses and aging behaviors of three new aluminum alloys. Alloys produced from rapidly solidified powders and contain 3.20 to 5.15 percent copper, 0.24 to 1.73 percent magnesium, 0.08 to 0.92 percent iron, and smaller amounts of manganese, nickel, titanium, silicon, and zinc. Peak hardness achieved at lower aging temperatures than with standard ingot-metallurgy alloys. Alloys of interest for automobile, aircraft, and aerospace applications.

  9. Damage on 316LN stainless steel transformed by powder metallurgy

    International Nuclear Information System (INIS)

    Couturier, R.; Burlet, H.

    1998-01-01

    This study deals with the 316 LN stainless steel elaboration by powder metallurgy. This method allows the realization of structures in austenitic steel less affected by the thermal aging than the cast austenitic-ferritic components. The components are performed by the method of HIP (Hot Isostatic Pressing). Mechanical tests are provided to control mechanical properties

  10. New model of enterprises resource planning implementation planning process in manufacturing enterprises

    Directory of Open Access Journals (Sweden)

    Mirjana Misita

    2016-05-01

    Full Text Available This article presents new model of enterprises resource planning implementation planning process in manufacturing enterprises based on assessment of risk sources. This assessment was performed by applying analytic hierarchy process. Analytic hierarchy process method allows variation of relative importance of specific risk sources dependent on the section from which the risk source originates (organizational environment, technical issues, people issues, adoption process management, and external support. Survey was conducted on 85 manufacturing enterprises involved with an enterprises resource planning solution. Ranking of risk sources assessments returns most frequent risks of enterprises resource planning implementation success in manufacturing enterprises, and representative factors were isolated through factor analysis by risk source origin. Finally, results indicate that there are hidden causes of failed implementation, for example, risk source “top management training and education,” from risk origin “adoption process management.”

  11. Compatibility of Anti-Wear Additives with Non-Ferrous Engine Bearing Alloys

    Energy Technology Data Exchange (ETDEWEB)

    Qu, Jun [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Zhou, Yan [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States)

    2017-01-01

    Investigate the compatibility of engine lubricant antiwear (AW) additives, specifically conventional zinc dialkyldithiophosphate (ZDDP) and newly developed ionic liquids (ILs), with selected non-ferrous engine bearing alloys, specifically aluminum and bronze alloys that are commonly used in connecting rod end journal bearings and bushings, to gain fundamental understanding to guide future development of engine lubricants

  12. System-functional approach in enterprise''s innovation activity management

    OpenAIRE

    Olikh, L.; Maslyukivska, А.

    2012-01-01

    The article is devoted to the problems of forming management system of enterprise innovation activity. The authors pick out the enterprise's innovation subsystem main parts and generalize management functions' realization in the context of its innovation activity management.

  13. Minority Business Enterprises and Woman Business Enterprises Grant Utilization

    Science.gov (United States)

    The policy goal of the MBE/WBE Programs is to assure that minority business enterprises and woman business enterprises are given the opportunity to participate in contract and procurement for supplies, construction, equipment & services under any EPA grant

  14. Minority Business Enterprise/Women's Business Enterprise (MBE/WBE) overview

    Science.gov (United States)

    The data base allows Minority Business Enterprise/Women's Business Enterprise (MBE/WBE) Coordinators to input fair share goals negotiated by EPA and the recipient. This system also provides to all users the ability to see recipient fair share goals.

  15. Iron deficiency up-regulates iron absorption from ferrous sulphate but not ferric pyrophosphate and consequently food fortification with ferrous sulphate has relatively greater efficacy in iron-deficient individuals

    NARCIS (Netherlands)

    Zimmermann, M.B.; Biebinger, R.; Egli, I.; Zeder, C.; Hurrell, R.F.

    2011-01-01

    Fe absorption from water-soluble forms of Fe is inversely proportional to Fe status in humans. Whether this is true for poorly soluble Fe compounds is uncertain. Our objectives were therefore (1) to compare the up-regulation of Fe absorption at low Fe status from ferrous sulphate (FS) and ferric

  16. The 6th European metallurgical conference EMC 2011: Proceedings review

    Directory of Open Access Journals (Sweden)

    Srećko R. Stopić

    2011-10-01

    Full Text Available The GDMB Society for Mining, Metallurgy, Resource and Environmental Technology organized the 6th European Metallurgical Conference (2011 in Duesseldorf from June 26 to 29, 2011. The same venue hosted the most important international metallurgical trade fairs for metallurgy of iron and steel, new casting and thermochemical processes METEC, GIFA, THERMOPROCESS and NEWCAST. The previous European metallurgical conferences were organized by GDMB in Friedrichshafen (2001, Hanover (2003, Leipzig (2005, Duesseldorf (2007, Innsbruck (2009. The GDMB is a non-profit organization situated in Clausthal in Germany, which is related to combining science with the practical experience in metallurgy, mining, materials engineering, mineral processing, recycling and refining of metals, and manufacturing of semi- and finishing products. The European Metallurgical conference EMC is one of the most known conferences worldwide in the field of non-ferrous metallurgy and is attended regularly by the decision makers from the industry and universities. The scientific program contained 6 plenary lectures and more than 160 presentations from 40 countries in 5 parallel series. An extensive poster exhibition was held, during which the authors had an opportunity to introduce their posters to the entire plenum as a part of a brief presentation. The best poster from the Montan-University in Leoben, Austria, was awarded the € 500 'Poster Award EMC 2011'. Not only were the most important European countries represented here, more than one third of the lecturers were from the non-European countries (Canada, Japan, China, USA, South Africa, Australia. The origin of the participants reflects the aim of the organizers: to make this conference a worldwide platform for the scientific exchange of experience and information. More than 400 participants from all over the world participated at this conference. The scientific presentations of the conference are presented in five Proceedings

  17. Contribution of nuclear analysis methods to the certification of BCR reference materials for non-metals in non-ferrous metals

    International Nuclear Information System (INIS)

    Pauwels, J.

    1979-01-01

    A number of reference materials for oxygen in different non-ferrous metals have been certified by BCR in the frame of a multidisciplinary Community project. The contribution of nuclear analysis methods is illustrated by several examples concerning the optimization of sample preparation techniques, the analysis of low and high oxygen non-ferrous metals and the extension of the program to other non-metals, especially nitrogen and carbon. (author)

  18. [Risk and features of occupational diseases in nonferrous metallurgy workers of Kolsky Transpolar area].

    Science.gov (United States)

    Siurin, S A; Chashchin, V P; Frolova, N M

    2015-01-01

    The study covered data on 977 cases of occupational diseases in 615 workers of nonferrous metallurgy in Kolsky Transpolar area. Findings are high risk of occupational diseases in workers engaged into electrolysis production of aluminium, all nickel reprocessing and pyrometallic copper reprocessing (GR 7.02-10.0). Electrolysis operators and anode operators of aluminium production are more prone to occupational diseases, with bone and muscular disorders (46.8%) prevalent in the morbidity structure. Respiratory diseases are more prevalent (68.2-100%) in the occupational morbidity structure of copper-nickelindustry workers. Conclusion is made on mandatory improvement of the work conditions and more effective individual protective means against occupational hazards in workers of nonferrous metallurgy in Kolsky Transpolar area.

  19. Price variability and marketing method in non-ferrous metals: Slade's analysis revisited

    NARCIS (Netherlands)

    Gilbert, C.L.; Ferretti, F.

    2002-01-01

    We examine the impact of the pricing regime on price variability with reference to the non-ferrous metals industry. Theoretical arguments are ambiguous, but suggest that the extent of monopoly power is more important than the pricing regime as a determinant of variability. Slade (Quart. J. Econ. 106

  20. Thermogravimetric control of intermediate compounds in uranium metallurgy; Control termogravimetrico de productos intermedios de la metalurgia del uranio

    Energy Technology Data Exchange (ETDEWEB)

    Gasco Sanchez, L; Fernandez Cellini, R

    1959-07-01

    The thermal decomposition of some intermediate compounds in the metallurgy of the uranium as uranium peroxide, ammonium uranate, uranium and ammonium penta-fluoride, uranium tetrafluoride and uranous oxide has been study by means of the Chevenard's thermo balance. Some data on pyrolysis of synthetic mixtures of intermediate compounds which may occasionally appear during the industrial process, are given. Thermogravimetric methods of control are suggested, usable in interesting products in the uranium metallurgy. (Author) 20 refs.

  1. 26 CFR 509.106 - Control of a United States enterprise by a Swiss enterprise.

    Science.gov (United States)

    2010-04-01

    ... 26 Internal Revenue 19 2010-04-01 2010-04-01 false Control of a United States enterprise by a Swiss enterprise. 509.106 Section 509.106 Internal Revenue INTERNAL REVENUE SERVICE, DEPARTMENT OF THE... a United States enterprise by a Swiss enterprise. In effect, Article IV of the convention provides...

  2. Power metallurgy approaches to high temperature components for gas turbine engines

    Science.gov (United States)

    Probst, H. B.

    1974-01-01

    Work conducted by NASA and NASA contractors on prealloyed superalloy powders and materials strengthened by oxide dispersion is reviewed. Fabrication, tensile strength, superplasticity, grain growth control, stress rupture life, and grain-size and dispersion-level effects are covered. Distinct strength advantages of powder metallurgy superalloys over conventional wrought alloys are noted.

  3. The enterprise engineering domain

    CSIR Research Space (South Africa)

    De Vries, M

    2015-06-01

    Full Text Available Enterprise engineering (EE) is emerging as a new discipline to address the design of the enterprise in a holistic way. Although existing knowledge on enterprise design is dispersed and fragmented across different disciplines and approaches, previous...

  4. PROCESSING OF SOFT MAGNETIC MATERIALS BY POWDER METALLURGY AND ANALYSIS OF THEIR PERFORMANCE IN ELECTRICAL MACHINES

    Directory of Open Access Journals (Sweden)

    W. H. D. Luna

    2017-12-01

    Full Text Available This article presents the use of finite elements to analyze the yield of electric machines based on the use of different soft magnetic materials for the rotor and the stator, in order to verify the performance in electric machine using powder metallurgy. Traditionally, the cores of electric machines are built from rolled steel plates, thus the cores developed in this work are obtained from an alternative process known as powder metallurgy, where powders of soft magnetic materials are compacted and sintered. The properties of interest were analyzed (magnetic, electric and mechanical properties and they were introduced into the software database. The topology of the rotor used was 400 W three-phase synchronous motor manufactured by WEG Motors. The results show the feasibility to replace the metal sheets of the electric machines by solid blocks obtained by powder metallurgy process with only 0.37% yield losses. In addition, the powder metallurgical process reduces the use of raw materials and energy consumption per kg of raw material processed.

  5. [Analysis of changes in characteristics of arterial hypertension occupational risk in workers of nonferrous metallurgy].

    Science.gov (United States)

    Vlasova, E M; Shliapnikov, D M; Lebedeva, T M

    2015-01-01

    The article covers changes in occupational cardiovascular risk for workers of nonferrous,metallurgy. Findings are that exposure to noise up to 94 dB with length of service increases possible atherosclerosis and metabolic syndrome. With 5 years of service, risk of the predicted conditions increases by 40.5%. When occupational exposure lasts over 5 years, risk of arterial hypertension increases. A group of workers without exposure to occupational factors appeared to have no connection between length of service and metabolic syndrome and arterial hypertension. Risk evolution modelling proved that risk of functional disorders in nonferrous metallurgy workers becomes unacceptable after 5 years of service (cardiovascular disorders are critical).

  6. Enterprise, Entrepreneurship and Ethics

    DEFF Research Database (Denmark)

    Hjorth, Daniel; Holt, Robin

    In the wake of calls for enterprise-led recovery amid Western economies, we critically investigate the enterprise discourse. Specifically, we challenge the association of enterprise and entrepreneurial activity. Using Foucault’s concept of parrrhesia - an ethical condition of brave speech - we ar...

  7. 78 FR 48468 - Hewlett Packard Company, Hewlett Packard Enterprise Business Unit, EG HP Storage, Enterprise...

    Science.gov (United States)

    2013-08-08

    ..., Hewlett Packard Enterprise Business Unit, EG HP Storage, Enterprise Storage, Servers and Networking Storage, APP Management, Research and Development Group, Andover, Massachusetts; Notice of Investigation... Enterprise Business Unit, EG HP Storage, Enterprise Storage, Servers and Networking Storage Division, APP...

  8. Experimental determination of the diffusion coefficient in two-dimensions in ferrous sulphate gels using the finite element method

    International Nuclear Information System (INIS)

    Baldock, C.; Harris, P.J.; Piercy, A.R.; Healy, B.

    2001-01-01

    A novel two-dimensional finite element method for modelling the diffusion which occurs in Fricke or ferrous sulphate type radiation dosimetry gels is presented. In most of the previous work, the diffusion coefficient has been estimated using simple one-dimensional models. This work presents a two-dimensional model which enables the diffusion coefficient to be determined in a much wider range of experimental situations. The model includes the provision for the determination of a drift parameter. To demonstrate the technique comparative diffusion measurements between ferrous sulphate radiation dosimetry gels, with and without xylenol orange chelating agent and carbohydrate additives have been undertaken. Diffusion coefficients of 9.7±0.4, 13.3±0.6 and 9.5±0.8 10-3 cm 2 per h -1 were determined for ferrous sulphate radiation dosimetry gels with and without xylenol orange and with xylenol orange and sucrose additives respectively. Copyright (2001) Australasian College of Physical Scientists and Engineers in Medicine

  9. Characterization of strengthening mechanism and hot deformation behavior of powder metallurgy molybdenum

    International Nuclear Information System (INIS)

    Xiao, Meili; Li, Fuguo; Xie, Hangfang; Wang, Yufeng

    2012-01-01

    Highlights: → Dynamic recrystallization of powder metallurgy molybdenum occurs in the temperature region (1200-1450 o C). → The value of strain hardening index n decreases along with the temperature rising. → The value of strain-rate sensitivity exponent m increases slowly at first and achieves a peak value at 1350 o C. → Deformation strengthening is the main strengthening mechanism at low temperature. → Rheological strengthening becomes the primary strengthening mechanism at high temperature. -- Abstract: The high-temperature deformation behavior of powder metallurgy molybdenum has been investigated based on a series of isothermal hot compression tests, which were carried out on a Gleeble-1500 thermal mechanical simulator in a wide range of temperatures (900-1450 o C) and strain rates (0.01-10 s -1 ). Through the research on the experimental stress-strain curves, it reveals that dynamic recrystallization softening effect of powder metallurgy molybdenum occurs in the temperature range from 1200 o C to 1450 o C, in which the flow stress is significantly sensitive to temperature. In comparison with the value of strain hardening index n which decreases along with the temperature rising, the value of strain-rate sensitivity exponent m does not change obviously; however, it increases slowly with the increasing of temperature at first and achieves a peak value at 1350 o C. Furthermore, relying on the comparison of mean value of n and m, it is suggested that deformation strengthening is the main strengthening mechanism at low temperature while the rheological strengthening changes into the primary strengthening mechanism at high temperature.

  10. VEM: Virtual Enterprise Methodology

    DEFF Research Database (Denmark)

    Tølle, Martin; Vesterager, Johan

    2003-01-01

    This chapter presents a virtual enterprise methodology (VEM) that outlines activities to consider when setting up and managing virtual enterprises (VEs). As a methodology the VEM helps companies to ask the right questions when preparing for and setting up an enterprise network, which works...

  11. Thermogravimetric control of intermediate compounds in uranium metallurgy; Control termogravimetrico de productos intermedios de la metalurgia del uranio

    Energy Technology Data Exchange (ETDEWEB)

    Gasco Sanchez, L.; Fernandez Cellini, R.

    1959-07-01

    The thermal decomposition of some intermediate compounds in the metallurgy of the uranium as uranium peroxide, ammonium uranate, uranium and ammonium penta-fluoride, uranium tetrafluoride and uranous oxide has been study by means of the Chevenard's thermo balance. Some data on pyrolysis of synthetic mixtures of intermediate compounds which may occasionally appear during the industrial process, are given. Thermogravimetric methods of control are suggested, usable in interesting products in the uranium metallurgy. (Author) 20 refs.

  12. Inquiry and Enterprise Transformation

    Science.gov (United States)

    Bonney, Dean J.

    What really constitutes an Enterprise from an Enterprise Systems Engineering perspective? My effort to create a workable definition follows: An Enterprise is a complex system of community, individual, and semiotic systems defined by the way its authentic relationships are constructed and dependent on the ways the parties to these relationships bind to one another. The imprint of an Enterprise is projected through its spatial identity, an identity that builds and maintains its currency through the positive images and authentic relationships it embraces.

  13. Acceptance of enterprise resource planning systems by small manufacturing enterprises

    CSIR Research Space (South Africa)

    Adam, R

    2011-06-01

    Full Text Available systems by small enterprises. This paper addresses this gap by considering the strategic, business, technical and human factors that influence the acceptance of ERP systems in small manufacturing enterprises in South Africa. The consultative list...

  14. Evaluation of effects of Maṇḍurabhasma on structural and functional integrity of small intestine in comparison with ferrous sulfate using an experimental model of iron deficiency anemia

    Directory of Open Access Journals (Sweden)

    Suchita Rajanikant Gawde

    2015-01-01

    Conclusion: Rats receiving a high dose of MB have shown improvement in hematinic and lactase levels comparable to those receiving ferrous sulfate. However, it causes lesser oxidative damage as compared to ferrous sulfate. This is an encouraging finding because it indicates the potential of MB to cause lesser gastrointestinal side effects compared to ferrous sulfate.

  15. Sustainable Enterprise Excellence

    DEFF Research Database (Denmark)

    Edgeman, Rick

    2013-01-01

    Structured Abstract Purpose: Sustainable Enterprise Excellence (SEE) is defined and developed through integration and expansion of business excellence modeling and sustainability thought. The intent is to enable simple yet reliable enterprise assessment of triple bottom line (TBL) performance...... and produce actionable enterprise foresight that can enable next best practices and sources of sustainable competitive advantage through innovation. Methodology: Key elements of SEE are identified from various business excellence and sustainability reporting sources, including the Global Reporting Initiative...... assessment approach similar in structure to those behind established excellence awards are developed that enable enterprise assessment of progress toward SEE. The resulting assessment is delivered in a highly consumable, combined narrative and graphic format referred to as a SEE NEWS Report. Practical...

  16. Lesotho - Enterprise Survey

    Data.gov (United States)

    Millennium Challenge Corporation — The 2011 MCA-Lesotho baseline enterprise survey is a national survey of enterprises. The main objective of the survey was to assess the current status of businesses...

  17. Powder metallurgy approaches to high temperature components for gas turbine engines

    Science.gov (United States)

    Probst, H. B.

    1974-01-01

    Research is reported for the tensile strength, ductility, and heat performance characterisitics of powder metallurgy (p/m) superalloys. Oxide dispersion strengthened alloys were also evaluated for their strength during thermal processing. The mechanical attributes evident in both p/m supperalloys and dispersion strengthened alloys are discussed in terms of research into their possible combination.

  18. Fractionation study in bioleached metallurgy wastes using six-step sequential extraction.

    Science.gov (United States)

    Krasnodebska-Ostrega, Beata; Pałdyna, Joanna; Kowalska, Joanna; Jedynak, Łukasz; Golimowski, Jerzy

    2009-08-15

    The stored metallurgy wastes contain residues from ore processing operations that are characterized by relatively high concentrations of heavy metals. The bioleaching process makes use of bacteria to recover elements from industrial wastes and to decrease potential risk of environmental contamination. Wastes were treated by solutions containing bacteria. In this work, the optimized six-stage sequential extraction procedure was applied for the fractionation of Ni, Cr, Fe, Mn, Cu and Zn in iron-nickel metallurgy wastes deposited in Southern Poland (Szklary). Fractionation and total concentrations of elements in wastes before and after various bioleaching treatments were studied. Analyses of the extracts were performed by ICP-MS and FAAS. To achieve the most effective bioleaching of Zn, Cr, Ni, Cu, Mn, Fe the usage of both autotrophic and heterotrophic bacteria in sequence, combined with flushing of the residue after bioleaching is required. 80-100% of total metal concentrations were mobilized after the proposed treatment. Wastes treated according to this procedure could be deposited without any risk of environmental contamination and additionally the metals could be recovered for industrial purposes.

  19. Microstructural and mechanical characteristics of porous iron prepared by powder metallurgy.

    Science.gov (United States)

    Capek, Jaroslav; Vojtěch, Dalibor

    2014-10-01

    The demand for porous biodegradable load-bearing implants has been increasing recently. Based on investigations of biodegradable stents, porous iron may be a suitable material for such applications. In this study, we prepared porous iron samples with porosities of 34-51 vol.% by powder metallurgy using ammonium bicarbonate as a space-holder material. We studied sample microstructure (SEM-EDX and XRD), flexural and compressive behaviors (universal loading machine) and hardness HV5 (hardness tester) of the prepared samples. Sample porosity increased with the amount of spacer in the initial mixtures. Only the pore surfaces had insignificant oxidation and no other contamination was observed. Increasing porosity decreased the mechanical properties of the samples; although, the properties were still comparable with human bone and higher than those of porous non-metallic biomaterials and porous magnesium prepared in a similar way. Based on these results, powder metallurgy appears to be a suitable method for the preparation of porous iron for orthopedic applications. Copyright © 2014 Elsevier B.V. All rights reserved.

  20. Were mercury emission factors for Chinese non-ferrous metal smelters overestimated? Evidence from onsite measurements in six smelters

    International Nuclear Information System (INIS)

    Zhang Lei; Wang Shuxiao; Wu Qingru; Meng Yang; Yang Hai; Wang Fengyang; Hao Jiming

    2012-01-01

    Non-ferrous metal smelting takes up a large proportion of the anthropogenic mercury emission inventory in China. Zinc, lead and copper smelting are three leading sources. Onsite measurements of mercury emissions were conducted for six smelters. The mercury emission factors were 0.09–2.98 g Hg/t metal produced. Acid plants with the double-conversion double-absorption process had mercury removal efficiency of over 99%. In the flue gas after acid plants, 45–88% was oxidized mercury which can be easily scavenged in the flue gas scrubber. 70–97% of the mercury was removed from the flue gas to the waste water and 1–17% to the sulfuric acid product. Totally 0.3–13.5% of the mercury in the metal concentrate was emitted to the atmosphere. Therefore, acid plants in non-ferrous metal smelters have significant co-benefit on mercury removal, and the mercury emission factors from Chinese non-ferrous metal smelters were probably overestimated in previous studies. - Highlights: ► Acid plants in smelters provide significant co-benefits for mercury removal (over 99%). ► Most of the mercury in metal concentrates for smelting ended up in waste water. ► Previously published emission factors for Chinese metal smelters were probably overestimated. - Acid plants in smelters have high mercury removal efficiency, and thus mercury emission factors for Chinese non-ferrous metal smelters were probably overestimated.

  1. Surface grinding characteristics of ferrous metals under high-speed and speed-stroke grinding conditions

    International Nuclear Information System (INIS)

    Ghani, A.K.; Choudhury, I.A.; Ahim, M.B.

    1999-01-01

    Some ferrous metals have been ground under different conditions with high-speed and speed-stroke in surface grinding operation. The paper describes experimental investigation of grinding forces in grinding some ferrous metals with the application of cutting fluids. Grinding tests have been carried out on mild steel, assab steel and stainless steel with different combinations of down feed and cross feed. The wheel speed was 27 m/sec while the table speed was maintained at the maximum possible 25 m/min. The grindability has been evaluated by measuring the grinding forces, grinding ratio, and surface finish. Grinding forces have been plotted against down feed of the grinding wheel and cross feed of the table. It has been observed that the radial and tangential grinding forces in stainless steel were higher than those in assab steel and mild steel

  2. Biaxially textured articles formed by powder metallurgy

    Science.gov (United States)

    Goyal, Amit; Williams, Robert K.; Kroeger, Donald M.

    2003-07-29

    A biaxially textured alloy article having a magnetism less than pure Ni includes a rolled and annealed compacted and sintered powder-metallurgy preform article, the preform article having been formed from a powder mixture selected from the group of mixtures consisting of: at least 60 at % Ni powder and at least one of Cr powder, W powder, V powder, Mo powder, Cu powder, Al powder, Ce powder, YSZ powder, Y powder, Mg powder, and RE powder; the article having a fine and homogeneous grain structure; and having a dominant cube oriented {100} orientation texture; and further having a Curie temperature less than that of pure Ni.

  3. Biaxially textured articles formed by power metallurgy

    Science.gov (United States)

    Goyal, Amit; Williams, Robert K.; Kroeger, Donald M.

    2003-08-26

    A biaxially textured alloy article having a magnetism less than pure Ni includes a rolled and annealed compacted and sintered powder-metallurgy preform article, the preform article having been formed from a powder mixture selected from the group of mixtures consisting of: at least 60 at % Ni powder and at least one of Cr powder, W powder, V powder, Mo powder, Cu powder, Al powder, Ce powder, YSZ powder, Y powder, Mg powder, and RE powder; the article having a fine and homogeneous grain structure; and having a dominant cube oriented {100} orientation texture; and further having a Curie temperature less than that of pure Ni.

  4. Biaxially textured articles formed by powder metallurgy

    Science.gov (United States)

    Goyal, Amit; Williams, Robert K.; Kroeger, Donald M.

    2003-08-05

    A biaxially textured alloy article having a magnetism less than pure Ni includes a rolled and annealed compacted and sintered powder-metallurgy preform article, the preform article having been formed from a powder mixture selected from the group of ternary mixtures consisting of: Ni powder, Cu powder, and Al powder, Ni powder, Cr powder, and Al powder; Ni powder, W powder and Al powder; Ni powder, V powder, and Al powder; Ni powder, Mo powder, and Al powder; the article having a fine and homogeneous grain structure; and having a dominant cube oriented {100} orientation texture; and further having a Curie temperature less than that of pure Ni.

  5. Solid ferrous ammonium sulfate as a dosimeter at low temperatures and high doses

    International Nuclear Information System (INIS)

    Juarez-calderon, J.M.; Ramos B, S.; Negron M, A.

    2006-01-01

    This paper presents the results obtained from a study of the radiation induced oxidation of crystalline ferrous ammonium sulfate with gamma rays at 295 K, 263 K and 77 K and doses from 0 to 300 kGy. The radiation induced decomposition of ferrous ammonium sulfate has been studied by the dissolution of the irradiated salt in 0,8 N sulfuric acid. The main product is ferric ion (Fe 3+ ) and its molar concentration was determined spectrophotometrically in the UV region at 304 nm. The optical density values showed a linear dependence with dose, indicating that the data obtained might be used to create a calibrating curve. Color in irradiated salt changes from blue to green, yellow and orange according to the absorbed dose. The accuracy and the reproducibility of the system were tested. In addition, some other characteristics make possible the use of this system as a dosimeter, similar to Fricke chemical dosimeter, for studies and works at low temperatures and high doses. (authors)

  6. Solid ferrous ammonium sulfate as a dosimeter at low temperatures and high doses

    Energy Technology Data Exchange (ETDEWEB)

    Juarez-calderon, J.M.; Ramos B, S.; Negron M, A. [Mexico Univ. Nacional Autonoma, Instituto de Ciencias Nucleares (Mexico)

    2006-07-01

    This paper presents the results obtained from a study of the radiation induced oxidation of crystalline ferrous ammonium sulfate with gamma rays at 295 K, 263 K and 77 K and doses from 0 to 300 kGy. The radiation induced decomposition of ferrous ammonium sulfate has been studied by the dissolution of the irradiated salt in 0,8 N sulfuric acid. The main product is ferric ion (Fe{sup 3+}) and its molar concentration was determined spectrophotometrically in the UV region at 304 nm. The optical density values showed a linear dependence with dose, indicating that the data obtained might be used to create a calibrating curve. Color in irradiated salt changes from blue to green, yellow and orange according to the absorbed dose. The accuracy and the reproducibility of the system were tested. In addition, some other characteristics make possible the use of this system as a dosimeter, similar to Fricke chemical dosimeter, for studies and works at low temperatures and high doses. (authors)

  7. Quality-oriented production of brown-coal coke with due regard to its application in metallurgy and environmental protection; Qualitaetsgerechte Erzeugung von Braunkohlenkoks unter Beruecksichtigung der Anwendung in Metallurgie und Umweltschutz

    Energy Technology Data Exchange (ETDEWEB)

    Achtelik, M.; Erken, M.; Juessen, P.; Knapp, A. [Rheinbraun AG, Koeln (Germany)

    1998-12-31

    In the nineteen seventies the Fortuna Nord refining factory of Rheinbraun AG began to restructure its operations from domestic coal briquetting to the manufacture of industrial products. One of these products, high-temperature brown-coal coke, is produced in two hearth-type furnaces. Coke produced in these plants is mainly used in metallurgy and environmental engineering, in the latter especially for flue gas purification. Rheinbraun has succeeded in introducing a quality management system for brown-coal coke which ensures high quality and security of supply. (orig.) [Deutsch] Im Veredlungsbetrieb Fabrik Fortuna-Nord der Rheinbraun AG begann in den 70er Jahren der Strukturwandel vom Hausbrandbrikett zu Industrieprodukten. Eins dieser Produkte, der Hochtemperatur-Braunkohlenkoks, wird in zwei Herdofenanlagen erzeugt. Die Haupteinsatzbereiche des Herdofenkokses sind die Metallurgie sowie der Umweltschutz und hier insbesondere die Rauchgasreinigung. Um die hohe Produktqualitaet und die Liefersicherheit zu gewaehrleisten, hat Rheinbraun ein Qualitaetsmanagementsystem fuer Braunkohlenkoks erfolgreich eingefuehrt. (orig.)

  8. Institutional Transition from Welfare Enterprise to Social Enterprise: the Localization of Legislation and Policy in Chinese Context

    Directory of Open Access Journals (Sweden)

    Zhang Xiaomeng

    2016-03-01

    Full Text Available Welfare enterprises, which are intended to create jobs for disabled people, are the core component of China's welfare system. As the economic environment and regulations change, China's welfare enterprises, which cannot take effective measures from within and emerge strong in market competition, are stuck in a bottleneck where further development is difficult. Welfare enterprises have hit the ceiling in their development for lacking sustainable sources of capital and capabilities of capital operation, inefficient management model and uncompetitive products and services. To reverse the trend of decline and grow into strong market players, the transformation from welfare enterprise to social enterprise, embracing the features of enterprise and social objectives, as an alternative is of crucial importance. As a new hybrid economic form, social enterprise combines the efficiency of businesses and the public-good nature of welfare enterprises, representing win-win cooperation among the government, society, and business sector. Such development is an institutional transformation which boosts competitiveness and tackles tough issues welfare enterprises are facing. Shifting from welfare enterprises to social enterprises means an institutional transition, during the process of which international experience in legislation shall be learned and localized. This paper analyzes the development history of welfare enterprises by taking a comprehensive look at the salient points of existing laws, policies promulgated throughout history, implementation and performance, major problems etc. so as to explore the institutional transition from welfare enterprises to social enterprises, revealing possible legal and policy problems and making suggestions.

  9. Solvent Extraction of Copper: An Extractive Metallurgy Exercise for Undergraduate Teaching Laboratories

    Science.gov (United States)

    Smellie, Iain A.; Forgan, Ross S.; Brodie, Claire; Gavine, Jack S.; Harris, Leanne; Houston, Daniel; Hoyland, Andrew D.; McCaughan, Rory P.; Miller, Andrew J.; Wilson, Liam; Woodhall, Fiona M.

    2016-01-01

    A multidisciplinary experiment for advanced undergraduate students has been developed in the context of extractive metallurgy. The experiment serves as a model of an important modern industrial process that combines aspects of organic/inorganic synthesis and analysis. Students are tasked to prepare a salicylaldoxime ligand and samples of the…

  10. 26 CFR 521.106 - Control of a domestic enterprise by a Danish enterprise.

    Science.gov (United States)

    2010-04-01

    ... 26 Internal Revenue 19 2010-04-01 2010-04-01 false Control of a domestic enterprise by a Danish enterprise. 521.106 Section 521.106 Internal Revenue INTERNAL REVENUE SERVICE, DEPARTMENT OF THE TREASURY... Are Residents of Denmark and of Danish Corporations § 521.106 Control of a domestic enterprise by a...

  11. Enterprise Potential: Essence, Classification and Types

    Directory of Open Access Journals (Sweden)

    Turylo Anatolii M.

    2014-02-01

    Full Text Available The article considers existing approaches to classification of the enterprise potential as an economic notion. It offers own vision of classification of enterprise potential, which meets modern tendencies of enterprise development. Classification ensures a possibility of a wider description and assessment of enterprise potential and also allows identification of its most significant characteristics. Classification of the enterprise potential is developed by different criteria: by functions, by resource support, by ability to adapt, by the level of detection, by the spectrum of taking into account possibilities, by the period of coverage of possibilities and by the level of use. Analysis of components of the enterprise potential allows obtaining a complete and trustworthy assessment of the state of an enterprise. Adaptation potential of an enterprise is based on principles systemacy and dynamism, it characterises possibilities of adjustment of an enterprise to external and internal economic conditions.

  12. An architectural framework for virtual enterprise engineering

    DEFF Research Database (Denmark)

    Zwegers, Arian; Hannus, Matti; Tølle, Martin

    2001-01-01

    , especially concerning integration issues. This paper aims to lay down an architectural framework to support the set-up and operation of virtual enterprises. It supports virtual enterprise engineering. The framework might also be used to identify and position issues that play a role in the set......-up and operation of virtual enterprises. As such, it is useful to classify research projects on virtual enterprises as well.......Enterprises cooperate more extensively with other enterprises during the entire product life cycle. Temporary alliances between various enterprises emerge such as those in virtual enterprises. However, many enterprises experience difficulties in the formation and operation of virtual enterprises...

  13. Uranium mining and metallurgy library science and technology literature retrieval of network

    International Nuclear Information System (INIS)

    Tang Lilei

    2014-01-01

    This paper introduces the network resources and characteristics retrieve service of Beijing research Institute of Chemical Engineering of Metallurgy library, Analyzes the problems often encountered in the literature retrieval in science and technology, And puts forward the solution, Puts forward the thinking and Suggestions of science and technology literature retrieval. (author)

  14. Estimation and characterization of polycyclic aromatic hydrocarbons from magnesium metallurgy facilities in China.

    Science.gov (United States)

    Nie, Zhiqiang; Yang, Yufei; Tang, Zhenwu; Liu, Feng; Wang, Qi; Huang, Qifei

    2014-11-01

    Field monitoring was conducted to develop a polycyclic aromatic hydrocarbon (PAH) emission inventory for the magnesium (Mg) metallurgy industry in China. PAH emissions in stack gas and fly/bottom ash samples from different smelting units of a typical Mg smelter were measured and compared. Large variations of concentrations, congener patterns, and emission factors of PAHs during the oxidation and reduction stages in the Mg smelter were observed. The measured average emission factor (166,487 μg/t Mg) was significantly higher than those of other industrial sources. Annual emission from Mg metallurgy in 2012 in China was estimated at 116 kg (514 g BaPeq) for PAHs. The results of this study suggest that PAH emission from Mg industries should be considered by local government agencies. These data may be helpful for understanding PAH levels produced by the Mg industry and in developing a PAH inventory.

  15. Diagnostics of the Enterprise Export Potential

    Directory of Open Access Journals (Sweden)

    Skrynkovskyy Ruslan M.

    2016-11-01

    Full Text Available The aim of the article is to form and develop theoretical and methodological foundations for diagnostics of the enterprise export potential, which should be understood as a process of identification, analysis and assessment of the level of potential possibility and readiness of the enterprise to implement export activities taking into account the impact of interrelated internal variables (goals, technology, structure, tasks, educational and professional potential of the staff and factors of the enterprise external environment (customers, competitors, suppliers, intermediaries, contact audience, etc. in order to ensure a qualitatively new level of its development and formation of its prospects. It is determined that the key business indicators of the system for diagnostics of enterprise export potential are: the level of enterprises competitiveness in the international (global market; the level of competitiveness of enterprise products; the level of competitiveness of enterprise export products; the level of enterprise resource opportunities; the level of enterprise export performance. Prospects for further research in this direction are to develop a classification (specifically detailed list of objectives of the enterprise diagnostics by the level of detail (element, partial, complex, taking into account diagnostics of export potential of the enterprise as part of diagnostic objective.

  16. Profitability of wood harvesting enterprises

    Energy Technology Data Exchange (ETDEWEB)

    Penttinen, M. email: markku.penttinen@metla.fi; Mikkola, J. email: jarmo.mikkola@metla.fi; Rummukainen, A. email: arto.rummukainen@metla.fi

    2009-07-01

    The forest machine business is about 50 years old. The rapid technical development of machinery increased productivity up to the end of last century. In 2007, the total value of round and energy wood harvesting and silvicultural work operated by forest machine enterprises exceeded 570 mill. euro. According to the materials of the Vehicle Administration Finland and Statistics Finland there are about 1 600 active harvesting enterprises in the personal and business taxation system. Beside this, there are according to the Ministry of Agriculture and Forestry about 1 300 farmers who do harvesting as side business. About 1 000 enterprises working in June 2007 were studied with their retrospective economic analyses from 2001. The data includes all enterprises that had supplied closing of the accounts data. One-machine entrepreneurs represent more than a third of the number of enterprises, but only 13 percent of the turnover. Enterprises with seven or more machines represent less than ten percent of the number, but over twenty percent of the turnover. Enterprises are largest in eastern and northern Finland, where the average number of machines per enterprise exceeds three. Small enterprises are mostly singleowner business enterprises with a median turnover of 125 000 euros per annum. Partnerships and limited enterprises have double the median turnover of single-owner businesss. Limited companies turn over a median of 450 000 euro/y, representing 67 percent of total turnover. Median net profit varied between 6 and 10 percent of turnover in 2001-2007, but only between 2 and 4 percent where the wage adjustment is deducted from the profit. The wage adjustment is estimated as if the owners of single-owner businesses earn an operator's salary. Profit was highest in 2002 and lowest 2006. In the smallest enterprise class with a turnover of less than 75 000 euro/y, profit was lowest and negative in 2006 and 2007. The variation in profits between enterprises was also biggest in

  17. Research and application of enterprise resource planning system for foundry enterprises

    Directory of Open Access Journals (Sweden)

    Zhou Jianxin

    2013-01-01

    Full Text Available PPDB issues - four aspects of current management issues of foundry enterprises are discussed in this paper, including Production Management, Process Control, Duration Monitoring and Business Intelligence Data Analysis. Also a whole Enterprise Resource Planning (ERP solution for foundry enterprises is proposed. The solution contains many models, four of which are used to solve the PPDB issues. These are called SPDB models, which separately are the Single-piece management model (based on casting lifecycle, Process management model (based on task-driven technology, Duration monitoring model (based on surplus period, and Business intelligence data analysis model (based on data mining. An ERP system for foundry enterprises, named HZERP, was researched and developed, and applied to a sand casting company of single piece and small batch production. Qualitatively and quantitatively comparing the application effect before and after implementing the HZERP system, the result demonstrated that the foundry ERP system based on the SPDB models can help metal casting enterprises achieve the single-piece management, better regulate the production processes, improve production and delivery management, shorten the production cycle, reduce costs, and speed up the capital turnover to a large extent.

  18. The beginning of metallurgy in the southern Levant: a late 6th millennium CalBC copper awl from Tel Tsaf, Israel.

    Science.gov (United States)

    Garfinkel, Yosef; Klimscha, Florian; Shalev, Sariel; Rosenberg, Danny

    2014-01-01

    The beginning of metallurgy in the ancient Near East attracts much attention. The southern Levant, with the rich assemblage of copper artifacts from the Nahal Mishmar cave and the unique gold rings of the Nahal Qanah cave, is regarded as a main center of early metallurgy during the second half of the 5th millennium CalBC. However, a recently discovered copper awl from a Middle Chalcolithic burial at Tel Tsaf, Jordan Valley, Israel, suggests that cast metal technology was introduced to the region as early as the late 6th millennium CalBC. This paper examines the chemical composition of this item and reviews its context. The results indicate that it was exported from a distant source, probably in the Caucasus, and that the location where it was found is indicative of the social status of the buried individual. This rare finding indicates that metallurgy was first diffused [corrected] to the southern Levant through exchange networks and only centuries later involved local productionThis copper awl, the earliest metal artifact found in the southern Levant, indicates that the elaborate Late Chalcolithic metallurgy developed from a more ancient tradition.

  19. Reference models supporting enterprise networks and virtual enterprises

    DEFF Research Database (Denmark)

    Tølle, Martin; Bernus, Peter

    2003-01-01

    This article analyses different types of reference models applicable to support the set up and (re)configuration of Virtual Enterprises (VEs). Reference models are models capturing concepts common to VEs aiming to convert the task of setting up of VE into a configuration task, and hence reducing...... the time needed for VE creation. The reference models are analysed through a mapping onto the Virtual Enterprise Reference Architecture (VERA) based upon GERAM and created in the IMS GLOBEMEN project....

  20. Control of enterprise interfaces for supply chain enterprise modeling

    Energy Technology Data Exchange (ETDEWEB)

    Interrante, L.D. [Sandia National Labs., Albuquerque, NM (United States); Macfarlane, J.F. [Lawrence Berkeley Lab., CA (United States). Information and Computing Sciences Div.

    1995-04-01

    There is a current trend for manufacturing enterprises in a supply chain of a particular industry to join forces in an attempt to promote efficiencies and improve competitive position. Such alliances occur in the context of specific legal and business agreements such that each enterprise retains a majority of its business and manufacturing information as private and shares other information with its trading partners. Shared information may include enterprise demand projections, capacities, finished goods inventories, and aggregate production schedules. Evidence of the trend toward information sharing includes the recent emphases on vendor-managed inventories, quick response, and Electronic Data Interchange (EDI) standards. The increased competition brought on by the global marketplace is driving industries to consider the advantages of trading partner agreements. Aggregate-level forecasts, supply-chain production smoothing, and aggregate-level inventory policies can reduce holding costs, record-keeping overhead, and lead time in product development. The goal of this research is to orchestrate information exchange among trading partners to allow for aggregate-level analysis to enhance supply chain efficiency. The notion of Enterprise Interface Control (EIC) is introduced as a means of accomplishing this end.

  1. Enterprise Pattern: integrating the business process into a unified enterprise model of modern service company

    Science.gov (United States)

    Li, Ying; Luo, Zhiling; Yin, Jianwei; Xu, Lida; Yin, Yuyu; Wu, Zhaohui

    2017-01-01

    Modern service company (MSC), the enterprise involving special domains, such as the financial industry, information service industry and technology development industry, depends heavily on information technology. Modelling of such enterprise has attracted much research attention because it promises to help enterprise managers to analyse basic business strategies (e.g. the pricing strategy) and even optimise the business process (BP) to gain benefits. While the existing models proposed by economists cover the economic elements, they fail to address the basic BP and its relationship with the economic characteristics. Those proposed in computer science regardless of achieving great success in BP modelling perform poorly in supporting the economic analysis. Therefore, the existing approaches fail to satisfy the requirement of enterprise modelling for MSC, which demands simultaneous consideration of both economic analysing and business processing. In this article, we provide a unified enterprise modelling approach named Enterprise Pattern (EP) which bridges the gap between the BP model and the enterprise economic model of MSC. Proposing a language named Enterprise Pattern Description Language (EPDL) covering all the basic language elements of EP, we formulate the language syntaxes and two basic extraction rules assisting economic analysis. Furthermore, we extend Business Process Model and Notation (BPMN) to support EPDL, named BPMN for Enterprise Pattern (BPMN4EP). The example of mobile application platform is studied in detail for a better understanding of EPDL.

  2. Six Sigma Driven Enterprise Model Transformation

    Directory of Open Access Journals (Sweden)

    Raymond Vella

    2009-10-01

    Full Text Available Enterprise architecture methods provide a structured system to understand enterprise activities. However, existing enterprise modelling methodologies take static views of the enterprise and do not naturally lead to a path of improvement during enterprise model transformation. This paper discusses the need for a methodology to facilitate changes for improvement in an enterprise. The six sigma methodology is proposed as the tool to facilitate progressive and continual Enterprise Model Transformation to allow businesses to adapt to meet increased customer expectation and global competition. An alignment of six sigma with phases of GERAM life cycle is described with inclusion of Critical-To-Satisfaction (CTS requirements. The synergies of combining the two methodologies are presented in an effort to provide a more culturally embedded framework for Enterprise Model Transformation that builds on the success of six sigma.

  3. Structural and electrical properties of copper-nickel-aluminum alloys obtained by conventional powder metallurgy method

    International Nuclear Information System (INIS)

    Monteiro, Waldemar A.; Carrio, Juan A.G.; Silveira, C.R. da; Pertile, H.K.S.

    2009-01-01

    This work looked for to search out systematically, in scale of laboratory, copper-nickel-aluminum alloys (Cu-Ni-Al) with conventional powder metallurgy processing, in view of the maintenance of the electric and mechanical properties with the intention of getting electric connectors of high performance or high mechanical damping. After cold uniaxial pressing (1000 kPa), sintering (780 deg C) and convenient homogenization treatments (500 deg C for different times) under vacuum (powder metallurgy), the obtained Cu-Ni-Al alloys were characterized by optical microscopy, electrical conductivity, Vickers hardness. X rays powder diffraction data were collected for the sintered samples in order to a structural and microstructural analysis. The comparative analysis is based on the sintered density, hardness, macrostructures and microstructures of the samples. (author)

  4. Hyperfine interactions and structures of ferrous hydroxide and green rust II in sulfated aqueous media

    International Nuclear Information System (INIS)

    Olowe, A.A.; Genin, J.M.R.; Bauer, P.

    1988-01-01

    A sulfated ferrous hydroxide is obtained by mixing NaOH with melanterite depending on the R = [SO 4 -- ]/[OH - ] ratio and leading by oxidation to the green rust II transient compound. Hyperfine parameters are presented. (orig.)

  5. Metallurgy Department. Progress Report for the Period 1 January to 31 December 1984

    DEFF Research Database (Denmark)

    Risø National Laboratory, Roskilde

    The activities of the Metallurgy Department at Risø during 1984 are described. The work is presented in three chapters: General Materials Research, Technology and Materials Development, and Fuel Elements. A survey is given of the Department's participation in international collaboration and of its...

  6. Werkstoffwoche 98. Vol. 6. Symposium 8: Metals. Symposium 14: Metals modelling

    International Nuclear Information System (INIS)

    Kopp, R.; Beiss, P.; Herfurth, K.; Boehme, D.; Bormann, R.; Arzt, E.; Riedel, H.

    1999-01-01

    The proceedings volume contains the papers of the symposia dealing with metals and the focus is on the following subjects: Deformation, powder metallurgy, forming by casting processes, joining, materials physics (ferrous materials, light metal materials, composite materials, high-temperature materials, functional materials), intermetallic phases and foams, modelling calculations. 26 of the papers have been analysed and processed for individual document retrieval from the ENERGY database. (orig/MM) [de

  7. The Changing Role of the Enterprise Architect

    DEFF Research Database (Denmark)

    Gøtze, John

    2013-01-01

    Enterprise architecture is practiced in different ways, and there are different types of enterprise architects with quite different roles. This paper looks closer at the role of enterprise architects and the importance of the enterprise architects’ understanding of boundary issues in their practice....... The paper suggests that enterprise architects must focus on problem-finding more than problem-solving, and should develop not just more dialectic skills, but also dialogic skills. The paper also argues that the enterprise architects must gain a deeper understanding of the enterprise, and need to start...... working with other enterprise disciplines....

  8. JUNOS Enterprise Switching

    CERN Document Server

    Reynolds, Harry

    2009-01-01

    JUNOS Enterprise Switching is the only detailed technical book on Juniper Networks' new Ethernet-switching EX product platform. With this book, you'll learn all about the hardware and ASIC design prowess of the EX platform, as well as the JUNOS Software that powers it. Not only is this extremely practical book a useful, hands-on manual to the EX platform, it also makes an excellent study guide for certification exams in the JNTCP enterprise tracks. The authors have based JUNOS Enterprise Switching on their own Juniper training practices and programs, as well as the configuration, maintenanc

  9. Powder metallurgy development at SRL

    International Nuclear Information System (INIS)

    Peacock, H.B.

    1978-01-01

    Fuel for Savannah River Plant (SRP) reactors consists of extruded tubes with aluminum--uranium alloy cores clad with 8001 aluminum. The 235 U in the fuel is periodically recovered and recycled in new fuel assemblies. The buildup of 236 U in the enriched uranium requires increased total uranium contents to maintain reactivity in existing assembly designs. High level waste production from these tubes is proportional to the aluminum content; therefore, appreciable radioactive waste reductions result from lower aluminum--uranium ratios and thinner clad tubes. The casting process now used for fuel cores is limited to below 40 wt % U because of the reduced fabricability of high uranium alloys. To increase tube loading and reduce aluminum, the U 3 O 8 -Al powder metallurgy (P/M) process for fuel tubes is under development. Several fabricaion and irradiaion tests have been made using production conditions. Both small scale and production tests carried out at SRL for high-density P/M fuel development are discussed

  10. Enterprise architecture intelligence

    NARCIS (Netherlands)

    Veneberg, R.K.M.; Iacob, Maria Eugenia; van Sinderen, Marten J.; Bodenstaff, L.; Reichert, M.U.; Rinderle-Ma, S.; Grossmann, G.

    2014-01-01

    Combining enterprise architecture and operational data is complex (especially when considering the actual ‘matching’ of data with enterprise architecture objects), and little has been written on how to do this. Therefore, in this paper we aim to fill this gap and propose a method to combine

  11. Automated information system for analysis and prediction of production situations in blast furnace plant

    Science.gov (United States)

    Lavrov, V. V.; Spirin, N. A.

    2016-09-01

    Advances in modern science and technology are inherently connected with the development, implementation, and widespread use of computer systems based on mathematical modeling. Algorithms and computer systems are gaining practical significance solving a range of process tasks in metallurgy of MES-level (Manufacturing Execution Systems - systems controlling industrial process) of modern automated information systems at the largest iron and steel enterprises in Russia. This fact determines the necessity to develop information-modeling systems based on mathematical models that will take into account the physics of the process, the basics of heat and mass exchange, the laws of energy conservation, and also the peculiarities of the impact of technological and standard characteristics of raw materials on the manufacturing process data. Special attention in this set of operations for metallurgic production is devoted to blast-furnace production, as it consumes the greatest amount of energy, up to 50% of the fuel used in ferrous metallurgy. The paper deals with the requirements, structure and architecture of BF Process Engineer's Automated Workstation (AWS), a computer decision support system of MES Level implemented in the ICS of the Blast Furnace Plant at Magnitogorsk Iron and Steel Works. It presents a brief description of main model subsystems as well as assumptions made in the process of mathematical modelling. Application of the developed system allows the engineering and process staff to analyze online production situations in the blast furnace plant, to solve a number of process tasks related to control of heat, gas dynamics and slag conditions of blast-furnace smelting as well as to calculate the optimal composition of blast-furnace slag, which eventually results in increasing technical and economic performance of blast-furnace production.

  12. An introduction to enterprise modeling and simulation

    Energy Technology Data Exchange (ETDEWEB)

    Ostic, J.K.; Cannon, C.E. [Los Alamos National Lab., NM (United States). Technology Modeling and Analysis Group

    1996-09-01

    As part of an ongoing effort to continuously improve productivity, quality, and efficiency of both industry and Department of Energy enterprises, Los Alamos National Laboratory is investigating various manufacturing and business enterprise simulation methods. A number of enterprise simulation software models are being developed to enable engineering analysis of enterprise activities. In this document the authors define the scope of enterprise modeling and simulation efforts, and review recent work in enterprise simulation at Los Alamos National Laboratory as well as at other industrial, academic, and research institutions. References of enterprise modeling and simulation methods and a glossary of enterprise-related terms are provided.

  13. Al/ B4C Composites with 5 and 10 wt% Reinforcement Content Prepared by Powder Metallurgy

    International Nuclear Information System (INIS)

    Yusof Abdullah; Mohd Reusmaazran Yusof; Azali Muhammad; Nadira Kamarudin; Wilfred Sylvester Paulus; Roslinda Shamsudin; Nasrat Hannah Shudin; Nurazila Mat Zali

    2012-01-01

    The preparation, physical and mechanical properties of Al/ B 4 C composites with 5 and 10 wt.% reinforcement content were investigated. In order to obtain the feedstock with a low powder loading, B 4 C mixtures containing fine powders were investigated to obtain the optimal particle packing. The experimental results indicated that the fine containing 5 and 10 wt.% particles are able to prepare the feedstock with a good flowability. The composites fabricated by powder metallurgy have low densities and homogeneous microstructures. Additionally there is no interface reaction observed between the reinforcement and matrix by XRD analysis. The hardness of Al/ B 4 C composites prepared by powder metallurgy was high. (Author)

  14. VERAM: Virtual Enterprise Reference Architecture and Methodology

    DEFF Research Database (Denmark)

    Zwegers, Arian; Tølle, Martin; Vesterager, Johan

    2003-01-01

    Nowadays, enterprises cooperate more extensively with other enterprises during the entire product life cycle. Temporary alliances between various enterprises emerge such as those in Virtual Enterprises. However, many enterprises experience difficulties in the formation and operation of virtual en...

  15. [Investigation about prevention behavior for dust workers in machinery, ceramic, and metallurgy industry].

    Science.gov (United States)

    Shen, Fu-hai; Ma, Qing-kun; Xiao, Shu-yu; Cui, Feng-tao; Meng, Qing-di; Yang, Xiu-qing; Qi, Hui-sheng; Fan, Xue-yun; Yao, San-qiao

    2011-01-01

    The purposes of this thesis were to study the behavior about workers exposed to dust and provide scientific basis for health promotion. We designed a questionnaire and carry it on the 746 dust workers in the 3 representative corporations of Machinery, Ceramic, and Metallurgy Industry. All data were input into computer. And a database was established with Excel. SPSS11.5 statistical analysis software was used to analyze the influence on protecting behavioral between the application of qualifications, different jobs, training or protection, and other aspects etc. The rates were 94.4% and 75.3% about the regular physical examination and requirements for protective equipment. The rate of choosing an effective way of protection was generally low (15.4%). There was significant difference for among different educational background workers (P Metallurgy Industry. Those who were not educated had a lower using rate about the protection behavior, regular physical examination, and requirements for protective equipment than those educated.

  16. Research on Sichuan Cuisine Enterprises Crisis

    Directory of Open Access Journals (Sweden)

    Jianfei Nan

    2014-04-01

    Full Text Available It is impossible to avoid crisis for Sichuan cuisine enterprises. On the basis of emphasizing the importance of the research of Sichuan cuisine enterprises crisis, the paper mainly analyzed the issue of Sichuan cuisine enterprises crisis from three aspects including formation mechanism of Sichuan cuisine enterprises crisis, the impact mechanism of Sichuan cuisine enterprises crisis and its response measures(such as principles, methods and strategiesin order to provide an important reference so that Sichuan cuisine enterprises have a correct understanding of the crisis, effectively response to the crisis, and strengthen crisis management so as to achieve their scientific development themselves. To some extent, the paper is helpful to cope with the crisis and promote the safety operation of the enterprises which are facing the crisis.

  17. Characterization of Powder Metallurgy Processed Pure Magnesium Materials for Biomedical Applications

    Czech Academy of Sciences Publication Activity Database

    Březina, M.; Minda, J.; Doležal, P.; Krystýnová, M.; Fintová, Stanislava; Zapletal, J.; Wasserbauer, J.; Ptáček, P.

    2017-01-01

    Roč. 7, č. 11 (2017), č. článku 461. ISSN 2075-4701 Institutional support: RVO:68081723 Keywords : magnesium * powder metallurgy * cold pressing * hot pressing * EIS (Electrochemical impedance spectroscopy) * three-point bending test * corrosion Subject RIV: JK - Corrosion ; Surface Treatment of Materials OBOR OECD: Coating and films Impact factor: 1.984, year: 2016 http://www.mdpi.com/2075-4701/7/11/461

  18. Recycling of ferrous sulfate by the synthesis of a new super oxidant material 'Referox'

    Energy Technology Data Exchange (ETDEWEB)

    Evrard, O. [Universite Henri Poincare, Vandoeuvre (France); Dupre, B.; Jeannot, C.; Kanari, N.; Gaballah, I.; Ninane, L.; Verstraete, W.; Denomme, S.; Belsue, M.

    2001-07-01

    This European Union-sponsored project was initiated to develop a process to recycle industrial ferrous sulfate by the synthesis of a superoxidant containing hexavalent (FeVI) iron. Hexavalent iron, also called ferrates, can be used in decontamination of industrial effluents, decolorisation and purification of effluents from the textile and tanning industries, oxidation of cyanide to cyanates, soil remediation, water treatment and in a variety of other processes. Dry synthesis of potassium ferrate, using calcium hypochlorite as the oxidizing agent, was successful. By using chlorine instead of calcium hypochlorite and by partially substituting sodium hydroxide for potassium hydroxide the cost of the synthesis was significantly reduced. Recycling of ferrous sulfate at room temperature by the synthesis of potassium ferrate (FeVI) using gaseous chlorine instead of solid calcium hypochlorite was also successful. The yield of the synthesis was about 65 per cent for the used industrial ferrous sulfate samples. Large scale experimentation of the potassium ferrate synthesis was also carried out, obtaining potassium ferrate that remained stable for several months. The ferrates were used in the treatment of drinking water, wastewater, soil remediation, and effluent decontamination. Encouraging results were obtained. An additional benefit found was that use of the ferrates as bactericide for water treatment instead of chlorine gas eliminates the generation of halo-organic compounds which are suspected to be carcinogenic. 2 figs.

  19. Formalization of Technological Knowledge in the Field of Metallurgy using Document Classification Tools Supported with Semantic Techniques

    Directory of Open Access Journals (Sweden)

    Regulski K.

    2017-06-01

    Full Text Available The process of knowledge formalization is an essential part of decision support systems development. Creating a technological knowledge base in the field of metallurgy encountered problems in acquisition and codifying reusable computer artifacts based on text documents. The aim of the work was to adapt the algorithms for classification of documents and to develop a method of semantic integration of a created repository. Author used artificial intelligence tools: latent semantic indexing, rough sets, association rules learning and ontologies as a tool for integration. The developed methodology allowed for the creation of semantic knowledge base on the basis of documents in natural language in the field of metallurgy.

  20. The Social Responsibility of Enterprises

    DEFF Research Database (Denmark)

    Rosdahl, Anders

    More than 20 per cent of the Danish working age population is provided for by some form of public income transfer. The goal of the present government is that enterprises should employ more of these persons: Enterprises should become more socially responsible. The paper analyses enterprises...

  1. Enterprise Portals und Enterprise Application Integration - Begriffsbestimmung und Integrationskonzeptionen

    OpenAIRE

    Schelp, Joachim; Winter, Robert

    2002-01-01

    Unter den Stichworten »Enterprise Portals« und »Enterprise Application Integration« werden neue Herausforderungen an die Applikationsarchitektur der Unternehmungen gestellt. Bei beiden spielt die Integration vorhandener und das Einfügen neuer Applikationen eine große Rolle. Beiden Themen ist gemein, dass sie die Diskussion bestimmter technischer Konzepte aus den vergangenen Jahren fortsetzen: Portale stellen das moderne Frontend dar, über das die verschiedenen E-Business-Konzepte umgesetzt we...

  2. Management and Engineering of Virtual Enterprises

    DEFF Research Database (Denmark)

    Tølle, Martin

    ) Component layer: consists of reusable components and modules. - Each layer builds on the previous one, i.e. the VE concept is captured in VERA, and the VERA can be used to structure each of the VERAM components. * C) A methodology for virtual enterprise named VEM (Virtual Enterprise Methodology) - One...... to the set up of virtual enterprises. Types of work preparation include definitions (e.g. shared terminology), ICT support (e.g. infrastructure and applications), procedures (e.g. how to set up virtual enterprises, partner selection), reference models (e.g. contract models and product structure) and the like....... * B) A framework and a reference architecture for virtual enterprises named VERAM (Virtual Enterprise Reference Architecture and Methodology) and VERA (Virtual Enterprise Reference Architecture) respectively. - VERAM is a framework that structures the body of knowledge related to preparation, set up...

  3. Minimization of radioactive solid wastes from uranium mining and metallurgy

    International Nuclear Information System (INIS)

    Zhang Xueli; Xu Lechang; Wei Guangzhi; Gao Jie; Wang Erqi

    2010-01-01

    The concept and contents of radioactive waste minimization are introduced. The principle of radioactive waste minimization involving administration optimization, source reduction, recycling and reuse as well as volume reduction are discussed. The strategies and methods to minimize radioactive solid wastes from uranium mining and metallurgy are summarized. In addition, the benefit from its application of radioactive waste minimization is analyzed. Prospects for the research on radioactive so-lid waste minimization are made in the end. (authors)

  4. Powder Metallurgy Reconditioning of Food and Processing Equipment Components

    Science.gov (United States)

    Nafikov, M. Z.; Aipov, R. S.; Konnov, A. Yu.

    2017-12-01

    A powder metallurgy method is developed to recondition the worn surfaces of food and processing equipment components. A combined additive is composed to minimize the powder losses in sintering. A technique is constructed to determine the powder consumption as a function of the required metallic coating thickness. A rapid method is developed to determine the porosity of the coating. The proposed technology is used to fabricate a wear-resistant defectless metallic coating with favorable residual stresses, and the adhesive strength of this coating is equal to the strength of the base metal.

  5. Machinability of zinc-aluminum alloy5; zamzk5; alloy produced by powder metallurgy

    International Nuclear Information System (INIS)

    Adnan, I.O.; Momani, M.A.A.

    2007-01-01

    Powder metallurgy process (P/M) is repeatedly reported as a near-net or net-shape manufacturing process with the ability of producing parts of complicated or intricate shapes with high required dimensional accuracy and high surface quality. However, some finishing and machining operations are sometimes necessary and must be done to meet dimensional tolerances or accommodate design features that can be achieved during compaction such as transverse holes, undercuts and threads. Therefore, it is necessary to study the machinability of P/M products. ZAMAK5 alloy is widely used in engineering applications in the automobile industry, particularly in the manufacturing of bushes and recently self -lubricated bearings which are manufactured by the P/M process. Therefore it is anticipated that studying the machinability of this alloy as produced by the powder metallurgy process is worthwhile investigating. In this paper, the machinability of ZAMAK5, alloy produced by powder metallurgy, under different cutting conditions of speed, depth of cut and feed rate is carried out. Surface roughness was used as a criterion for assessing machinability at the different conditions. It was found that specimens compacted at 475 MPa and having 1% addition of zinc stearates as a binder and lubricant gave better surface quality than those produced at 550 MPa compacting pressure,whereas at 1.5% addition of zinc stearates produced worse surface quality (i.e. Higher surface roughness than in case of 475 MPa compacting pressure). On the whole, the results of the experimental work revealed that the surface roughness at the different cutting conditions remained within the accepted level in industry, less than 2 microns. (author)

  6. Enterprise architecture approach to mining companies engineering

    Directory of Open Access Journals (Sweden)

    Ilin’ Igor

    2017-01-01

    Full Text Available As Russian economy is still largely oriented on commodities production, there are a lot of cities where mining and commodity-oriented enterprises are the backbone of city economy. The mentioned enterprises mostly define the life quality of citizens in such cities, thus there are high requirements for engineering of city-forming enterprises. The paper describes the enterprise architecture approach for management system engineering of the mining enterprises. The paper contains the model of the mining enterprise architecture, the approach to the development and implementation of an integrated management system based on the concept of enterprise architecture and the structure of information systems and information technology infrastructure of the mining enterprise.

  7. Stress corrosion cracking of several high strength ferrous and nickel alloys

    Science.gov (United States)

    Nelson, E. E.

    1971-01-01

    The stress corrosion cracking resistance of several high strength ferrous and nickel base alloys has been determined in a sodium chloride solution. Results indicate that under these test conditions Multiphase MP35N, Unitemp L605, Inconel 718, Carpenter 20Cb and 20Cb-3 are highly resistant to stress corrosion cracking. AISI 410 and 431 stainless steels, 18 Ni maraging steel (250 grade) and AISI 4130 steel are susceptible to stress corrosion cracking under some conditions.

  8. Study of Anti-Fatigue Effect in Rats of Ferrous Chelates Including Hairtail Protein Hydrolysates

    Directory of Open Access Journals (Sweden)

    Saibo Huang

    2015-12-01

    Full Text Available The ability of ferrous chelates including hairtail protein hydrolysates to prevent and reduce fatigue was studied in rats. After hydrolysis of hairtail surimi with papain, the hairtail protein hydrolysates (HPH were separated into three groups by range of relative molecular weight using ultrafiltration membrane separation. Hairtail proteins were then chelated with ferrous ions, and the antioxidant activity, the amino acid composition and chelation rate of the three kinds of ferrous chelates including hairtail protein hydrolysates (Fe-HPH were determined. Among the three groups, the Fe-HPH chelate showing the best conditions was selected for the anti-fatigue animal experiment. For it, experimental rats were randomly divided into seven groups. Group A was designated as the negative control group given distilled water. Group B, the positive control group, was given glutathione. Groups C, D and E were designated as the Fe-HPH chelate treatment groups and given low, medium, and high doses, respectively. Group F was designated as HPH hydrolysate treatment group, and Group G was designated as FeCl2 treatment group. The different diets were orally administered to rats for 20 days. After that time, rats were subjected to forced swimming training after 1 h of gavage. Rats given Fe-FPH chelate had higher haemoglobin regeneration efficiency (HRE, longer exhaustive swimming time and higher SOD activity. Additionally, Fe-FPH chelate was found to significantly decrease the malondialdehyde content, visibly enhance the GSH-Px activity in liver and reduce blood lactic acid of rats. Fe-HPH chelate revealed an anti-fatigue effect, similar to or better than the positive control substance and superior to HPH or Fe when provided alone.

  9. Application of powder metallurgy in production of nuclear fuels for research and power reactors

    International Nuclear Information System (INIS)

    Fukuda, Kosaku

    2000-01-01

    Powder metallurgy has been applied in many of the processes of nuclear fuel fabrication, which has contributed, to a great progress of the nuclear technology to date. Evolution of nuclear fuels still continues to meet various emerging demands in terms of enhanced safety, economical effectiveness, non-proliferation and environmental mitigation. This paper reviews recent progress of nuclear fuels of research and power reactors, in particular, focusing on the powder metallurgy application. First, the review is made on plate type fuels for research reactors, inter alia, silicide fuel which is prevailing worldwide from the viewpoint of non-proliferation. The relation between fabrication and irradiation behavior is also discussed. Next, oxide fuels including MOX are reviewed. Recent interests of UO 2 are directed toward large grain pellets and burnable absorber pellets, both of which arise from requirement of extended burnup. Finally, the MOX fuel for thermal reactors is reviewed. (author)

  10. Obtainment of the alloy Cu13Al4Ni using processed by powder metallurgy

    International Nuclear Information System (INIS)

    Grossi, L.J.; Damasceno, N.; Muterlle, P.V.

    2016-01-01

    The powder metallurgy is a technique environmentally advantageous that allows the production of many pieces, with a good superficial finishing and dimensional tolerance. For the production of pieces using technique, basics steps are carried out, as the characterization of powders, the mixing and homogenization, compacting and sintering. In this context, this work has as objective the obtainment of the Cu13Al4Ni alloy via powder metallurgy. For this, was made a high energy milling for 2, 4 and 8 hours. Then, the milled powder was compacted and posteriorly, sintered in an oven with controlled atmosphere. It was observed that the milling time affects directly in sintering of the pieces. The best results obtained were for the samples that were milled for 4 hours. This samples have showed 21, 52% of porosity and 6,382 g/cm³ of the density of sintered. (author)

  11. Crisis management in metallurgical enterprises

    Directory of Open Access Journals (Sweden)

    B. Gajdzik

    2014-07-01

    Full Text Available On the basis of report analysis which presents situation in metallurgical sector after 2008 the range of changes implemented in management of metallurgical enterprises was characterised. A definition approach to crisis management was suggested as the process when the enterprise is managed during the breakdown period in market condition of the economy in the way directed towards preventing the negative effects of crisis inside enterprises. The publication presents the key aspects of enterprise management in the period of collapse of the balance between the supply and demand on the metallurgical market.

  12. Properties of porous magnesium prepared by powder metallurgy.

    Science.gov (United States)

    Čapek, Jaroslav; Vojtěch, Dalibor

    2013-01-01

    Porous magnesium-based materials are biodegradable and promising for use in orthopaedic applications, but their applications are hampered by their difficult fabrication. This work reports the preparation of porous magnesium materials by a powder metallurgy technique using ammonium bicarbonate as spacer particles. The porosity of the materials depended on the amount of ammonium bicarbonate and was found to have strong negative effects on flexural strength and corrosion behaviour. However, the flexural strength of materials with porosities of up to 28 vol.% was higher than the flexural strength of non-metallic biomaterials and comparable with that of natural bone. Copyright © 2012 Elsevier B.V. All rights reserved.

  13. Role-Oriented Enterprise Systems

    DEFF Research Database (Denmark)

    Holst, Philip; Beringer, Joerg; Winther, Jacob

    This paper examines the concept of role-­oriented enterprise systems by investigating motivations for and approaches to constructing and reflecting predefined organizational roles in user interfaces of packaged enterprise systems. The research is conducted as case studies of Microsoft and SAP......, constructed from interviews, documents, and examples of role-­‐oriented enterprise system packages from both vendors. The research indicates that the primary motivation of the vendors for including predefined roles is to complement a function-­‐centric approach with a user-­‐centric approach to the design...... of user interfaces of enterprise systems. The research furthermore identifies strategies of an embedded and an independent approach to modeling the role concept and a unified and a componentized approach to reflecting role aggregation in user interfaces....

  14. [Ferrous sulfate in the treatment of iron deficiency anemia: The positions continue].

    Science.gov (United States)

    Dvoretsky, L I

    The paper discusses treatment strategy and tactics for iron deficiency anemia. It gives data on the comparative efficacy of different iron sulfate drugs, their bioavailability, effects on peroxidation processes, and side effects. The paper also considers the clinical significance of a dosage form of iron-containing drugs with a sustained iron release, as well as ways to reduce the frequency and magnitude of side effects when ferrous sulfate is used.

  15. Decision-making regarding restructuring in multinational enterprises.

    OpenAIRE

    Ghertman M

    1986-01-01

    ILO pub. Working paper, evaluation of three case studies of decision making regarding enterprise restructuring in multinational enterprises originating in Canada, the USA and Western Europe - examines the role of management attitude, business organization, capital resources and size of enterprise in determining subsidiary enterprise creation, enterprise takeover, plant shutdown, resource allocation, labour utilization, etc. Diagrams, organigrams, references, tables.

  16. Magnetic Glass Ceramics by Sintering of Borosilicate Glass and Inorganic Waste

    OpenAIRE

    Ponsot, In?s M. M. M.; Pontikes, Yiannis; Baldi, Giovanni; Chinnam, Rama K.; Detsch, Rainer; Boccaccini, Aldo R.; Bernardo, Enrico

    2014-01-01

    Ceramics and glass ceramics based on industrial waste have been widely recognized as competitive products for building applications; however, there is a great potential for such materials with novel functionalities. In this paper, we discuss the development of magnetic sintered glass ceramics based on two iron-rich slags, coming from non-ferrous metallurgy and recycled borosilicate glass. The substantial viscous flow of the glass led to dense products for rapid treatments at relatively low te...

  17. Flotation concentration for tellurium determination in industrial sewage

    International Nuclear Information System (INIS)

    Skripchuk, V.G.; Bormotova, L.V.; Lukoyanova, L.P.; Tret'yakova, M.I.

    1983-01-01

    Combination of the flotation of tellurium (4) precipitate with papaverine toluene and extraction-photometric determination of Te with butylrhodamine C allows one to determine 0.002-0.1 mg Te/l without its preliminary precipitation. Accompanying elements found in non-ferrous metallurgy sewage have no effect upon it. The duration of analysis of 10 samples is 1 to 1.5 h. Relative error is 12%. The method is introduced at the ''Uralelektromed'' plant

  18. Modeling of Atmospheric Transport and Deposition of Heavy Metals in the Katowice Province

    OpenAIRE

    Uliasz, M.; Olendrzynski, K.

    1996-01-01

    A large part of Poland's heavy industry, notably hard coal mining, ferrous and nonferrous metallurgy and power generation, is located in the Katowice province. Therefore, this heavy industrialized region, which is populated by four million people, experiences considerable problems with air pollution. In the METKAT study launched by the International Institute for Applied Systems Analysis we attempt to model atmospheric depositions of arsenic (As), cadmium (Cd), lead (Pb) and zinc (Zn) which a...

  19. Mechanical properties of modified low cobalt powder metallurgy Udimet 700 type alloys

    Science.gov (United States)

    Harf, Fredric H.

    1989-01-01

    Eight superalloys derived from Udimet 700 were prepared by powder metallurgy, hot isostatically pressed, heat treated and their tensile and creep rupture properties determined. Several of these alloys displayed properties superior to those of Udimet 700 similarly prepared, in one case exceeding the creep rupture life tenfold. Filter clogging by extracted gamma prime, its measurement and significance are discussed in an appendix.

  20. Annual report of the Metallurgy Division - period ending December 1975

    International Nuclear Information System (INIS)

    1976-01-01

    The R and D activities of the Metallurgy Division of the Bhabha Atomic Research Centre, Bombay (India) during 1975 are described. Some of the R and D programmes of particular interest to nuclear technology are: (1) flowsheet development for the production of rare metals and alloys of nuclear use e.g. hafnium, beryllium, zirconium (2) metallurgical, irradiation hardening and corrosion studies on Zr and Zr-base alloys and (3) studies of nuclear ceramic materials such as UO2 and beryllia. (M.G.B.)

  1. Tax Planning for Enterprises

    Institute of Scientific and Technical Information of China (English)

    Fan Weiqing

    2011-01-01

    @@ Tax planning is legal planning activities for tax savings, meaning tax payers make operation plans within the national policy framework and choose operation programs favorable to tax savings.Along with a maturing socialist market economy system in China, tax planning is becoming an integral part of enterprise management and operation.For a better tax planning, enterprises have to fully understand the meaning, get proficient at relevant strategies, and apply these methods to save taxes and realize the maximization of enterprise value while considering the actual situation.

  2. Reuse of scrap of Al and steel SAE 1045 in metal composite as alternative of recycling route powder metallurgy

    International Nuclear Information System (INIS)

    Souza, V.E.S.; Masieiro, F.R.S.; Lourenco, J.M.; Felipe, R.C.T.S.

    2009-01-01

    Full text: The process of powder metallurgy in the production of parts through application of pressure on the selected ceramic or metal powders, which are subjected to a temperature of sintering for to occur consolidation of the components. The metal-mechanical industry is responsible for the generation of inputs from their manufacturing processes. This work aims to re-use of chips of Al and SAE 1045 steel by powder metallurgy of this is a viable and effective. This work is in the manufacture of a composite using Al 6060 metal matrix and steel 1045 as reinforcement (30%, 40%, 50%), under different compaction pressures (250MPa, 400MPa and 600MPa), analyzing the influence of compressibility in hardness of the compressed. The samples were sintered at a temperature of 500 ° C in an oven using resistive atmosphere of hydrogen for 45 minutes. After the procedures of the powder metallurgy technique were analyzed of the optical microscopy, x-ray diffraction, MEV and Rockwell hardness, which was found to be evaluated as not diffusibility between the steel and aluminum. (author)

  3. Grand Challenges of Enterprise Integration

    Energy Technology Data Exchange (ETDEWEB)

    Brosey, W.D; Neal, R.E.; Marks, D.

    2001-04-01

    Enterprise Integration connects and combines people, processes, systems, and technologies to ensure that the right people and the right processes have the right information and the right resources at the right time. A consensus roadmap for Technologies for Enterprise Integration was created as part of an industry/government/academia partnership in the Integrated Manufacturing Technology Initiative (IMTI). Two of the grand challenges identified by the roadmapping effort will be addressed here--Customer Responsive Enterprises and Totally Connected Enterprises. Each of these challenges is briefly discussed as to the current state of industry and the future vision as developed in the roadmap.

  4. Effect of vanadium carbide on dry sliding wear behavior of powder metallurgy AISI M2 high speed steel processed by concentrated solar energy

    Energy Technology Data Exchange (ETDEWEB)

    García, C. [Materials Engineering. E.I.I., Universidad de Valladolid. C/Paseo del cauce 59, 47011 Valladolid (Spain); Romero, A. [E.T.S. Ingenieros Industriales. Instituto de Investigaciones Energéticas y Aplicaciones Industriales (INEI). Universidad de Castilla-La Mancha, Edificio Politécnico, Avda. Camilo José Cela s/n, 13071 Ciudad Real (Spain); Herranz, G., E-mail: gemma.herranz@uclm.es [E.T.S. Ingenieros Industriales. Instituto de Investigaciones Energéticas y Aplicaciones Industriales (INEI). Universidad de Castilla-La Mancha, Edificio Politécnico, Avda. Camilo José Cela s/n, 13071 Ciudad Real (Spain); Blanco, Y.; Martin, F. [Materials Engineering. E.I.I., Universidad de Valladolid. C/Paseo del cauce 59, 47011 Valladolid (Spain)

    2016-11-15

    Mixtures of AISI M2 high speed steel and vanadium carbide (3, 6 or 10 wt.%) were prepared by powder metallurgy and sintered by concentrated solar energy (CSE). Two different powerful solar furnaces were employed to sinter the parts and the results were compared with those obtained by conventional powder metallurgy using a tubular electric furnace. CSE allowed significant reduction of processing times and high heating rates. The wear resistance of compacts was studied by using rotating pin-on-disk and linearly reciprocating ball-on-flat methods. Wear mechanisms were investigated by means of scanning electron microscopy (SEM) observations and chemical inspections of the microstructures of the samples. Better wear properties than those obtained by conventional powder metallurgy were achieved. The refinement of the microstructure and the formation of carbonitrides were the reasons for this. - Highlights: •Powder metallurgy of mixtures of M2 high speed steel and VC are studied. •Some sintering is done by concentrated solar energy. •Rotating pin-on-disk and linearly reciprocating ball-on-flat methods are used. •The tribological properties and wear mechanisms, under dry sliding, are studied.

  5. Metallurgy of high-silicon steel parts produced using Selective Laser Melting

    International Nuclear Information System (INIS)

    Garibaldi, Michele; Ashcroft, Ian; Simonelli, Marco; Hague, Richard

    2016-01-01

    The metallurgy of high-silicon steel (6.9%wt.Si) processed using Selective Laser Melting (SLM) is presented for the first time in this study. High-silicon steel has great potential as a soft magnetic alloy, but its employment has been limited due to its poor workability. The effect of SLM-processing on the metallurgy of the alloy is investigated in this work using microscopy, X-Ray Diffraction (XRD) and Electron Backscatter Diffraction (EBSD). XRD analysis suggests that the SLM high-silicon steel is a single ferritic phase (solid solution), with no sign of phase ordering. This is expected to have beneficial effects on the material properties, since ordering has been shown to make silicon steels more brittle and electrically conductive. For near-fully dense samples, columnar grains with a high aspect ratio and oriented along the build direction are found. Most importantly, a <001> fibre-texture along the build direction can be changed into a cube-texture when the qualitative shape of the melt-pool is altered (from shallow to deep) by increasing the energy input of the scanning laser. This feature could potentially open the path to the manufacture of three-dimensional grain-oriented high-silicon steels for electromechanical applications.

  6. Pay attention to the enterprise competitive intelligence analysis research promotion enterprise scientific research production and product development

    International Nuclear Information System (INIS)

    Yang Yan

    2014-01-01

    This article covers the competitive intelligence content and five characteristics, and on the American Competitive intelligence Outstanding Company's place situation, shows fully the competitive intelligence constructs the core competitive power regarding the enterprise to have the significant function, Its contribution has already hold the pivotal status in the world famous enterprise. It is an important cornerstone for enterprises which construct the core competitive power. Along with the enterprise competition environment rapid change, the competitive intelligence importance suddenly to reveal day by day. Just like the world richest family Microsoft Corporation president Bill. Gates asserted that, How to collect, How to analysis, how to manage and how to use information, lt will decide the enterprise victory and loss. And unified the enterprise scientific research production the special details, take 'To develop the SF_6 New Product' to introduce as the example how did the enterprise competition intelligence, as well as how did the information development and using in it. (author)

  7. Better Models for Agile Virtual Enterprises - the Enterprise and its Constituents as Hybrid Agents

    DEFF Research Database (Denmark)

    Bernus, Peter; Baltrusch, Rob; Tølle, Martin

    2003-01-01

    The article proposes a way to improve reference models for the management of virtual enterprises. The pattern of management roles is based on enveloping each decision centre into an agent wrapper, using the same tools and algorithms. Using this approach enterprises (organization, networks, virtual...... enterprises) will have the emergent agent property – the ability to follow objectives, plan, and take timely corrective action in case the plan breaks down....

  8. The Nature of Crisis in Enterprise Activities

    Directory of Open Access Journals (Sweden)

    Kozachenko Ganna V.

    2017-09-01

    Full Text Available It is shown that the concept of enterprise anti-crisis management and its components should be based on the nature of crisis in enterprise activities, the idea of which is the fundamental basis of enterprise anti-crisis management and determines its object, subject, tasks, main guidelines and vectors. Examples of defining the concept “crisis in enterprise activities”, which testify to the lack of unity of views on its content, are given. There revealed the attributive nature of crisis in enterprise activities, according to which a crisis, being an attribute of the system “enterprise”, begins intensifying under the influence of driving forces and individual factors, which is identified by presence of disruptions in the performance by the enterprise of its functions. There substantiated the expediency of singling out manifestations of crisis in enterprise activities (crisis phenomena, crisis situation and crisis state depending on the level of disruptions in the performance by the enterprise of its functions, which is of great importance for determining the tasks of enterprise anti-crisis management. The crisis cycle in enterprise activities in any of its manifestations is analysed, features of the cycle are considered.

  9. The marketing strategy of a small enterprise

    Directory of Open Access Journals (Sweden)

    Trandafilović Igor

    2008-01-01

    Full Text Available Small enterprise shows some specific characteristics which are necessary for creation of marketing strategy. The goal of this work is an attempt of marketing strategy analysis of the small enterprises. The necessary request of the analysis is to define the small enterprise. There have also been analyzed the specific orders for small enterpriser. Special part of work is dedicated to a small enterprises management strategy and the other one to their marketing communications. There are mentioned some specific advantages and problems of the small enterprises, too.

  10. The Impact of Enterprise Education on Attitudes to Enterprise in Young People: An Evaluation Study

    Science.gov (United States)

    Athayde, Rosemary

    2012-01-01

    Purpose: The purpose of the paper is to present evidence on the impact of enterprise education on young people still at school in London, UK. The study was designed to measure the effect of participation in a Young Enterprise (YE) Company Program on young people's attitudes toward starting a business, and on their enterprise potential.…

  11. The Extended Enterprise concept

    DEFF Research Database (Denmark)

    Larsen, Lars Bjørn; Vesterager, Johan; Gobbi, Chiara

    1999-01-01

    This paper provides an overview of the work that has been done regarding the Extended Enterprise concept in the Common Concept team of Globeman 21 including references to results deliverables concerning the development of the Extended Enterprise concept. The first section presents the basic concept...... picture from Globeman21, which illustrates the Globeman21 way of realising the Extended Enterprise concept. The second section presents the Globeman21 EE concept in a life cycle perspective, which to a large extent is based on the thoughts and ideas behind GERAM (ISO/DIS 15704)....

  12. The Energy Efficient Enterprise

    Energy Technology Data Exchange (ETDEWEB)

    Ahmad, Bashir

    2010-09-15

    Since rising energy costs have become a crucial factor for the economy of production processes, the optimization of energy efficiency is of essential importance for industrial enterprises. Enterprises establish energy saving programs, specific to their needs. The most important elements of these energy efficiency programs are energy savings, energy controlling, energy optimization, and energy management. This article highlights the industrial enterprise approach to establish sustainable energy management programs based on the above elements. Globally, if organizations follow this approach, they can significantly reduce the overall energy consumption and cost.

  13. Study on the formation of cubic texture in Ni-7 at.% W alloy substrates by powder metallurgy routes

    DEFF Research Database (Denmark)

    Zhao, Yue; Suo, HongLi; Zhu, YongHua

    2009-01-01

    One of the main challenges for coated conductor applications is to produce sharp cubic textured alloy substrates with high strength and low magnetism. In this work, the cubic textured Ni–7 at.% W substrates were prepared from different powder metallurgy ingots by rolling-assisted biaxially textured...... substrate processing. The fabrication processes of cubic texture in the Ni–7 at.% W tapes by two powder metallurgy routes are described in detail. Through the optimized process, full width at half maximum values of 6.7° and 5.0° were obtained, as estimated by X-ray (1 1 1) phi scan and (2 0 0) rocking curve...

  14. Extended Enterprise performance Management

    NARCIS (Netherlands)

    Bobbink, Maria Lammerdina; Hartmann, Andreas

    2014-01-01

    The allegiance of partnering organisations and their employees to an Extended Enterprise performance is its proverbial sword of Damocles. Literature on Extended Enterprises focuses on collaboration, inter-organizational integration and learning to avoid diminishing or missing allegiance becoming an

  15. Business Enterprise Program | Division of Vocational Rehabilitation

    Science.gov (United States)

    About Us > Business Enterprise Program Business Enterprise Program The Division of Vocational Rehabilitation's (DVR) Business Enterprise Program (BEP) provides employment opportunities to people who experience contact their DVR counselor or the BEP coordinator. List of Business Enterprise Program Vendors BEP Policy

  16. The ferrous iron transporter FtrABCD is required for the virulence of Brucella abortus 2308 in mice.

    Science.gov (United States)

    Elhassanny, Ahmed E M; Anderson, Eric S; Menscher, Evan A; Roop, R Martin

    2013-06-01

    Iron transport has been linked to the virulence of Brucella strains in both natural and experimental hosts. The genes designated BAB2_0837-0840 in the Brucella abortus 2308 genome sequence are predicted to encode a CupII-type ferrous iron transporter homologous to the FtrABCD transporter recently described in Bordetella. To study the role of the Brucella FtrABCD in iron transport, an isogenic ftrA mutant was constructed from B. abortus 2308. Compared with the parental strain, the B. abortus ftrA mutant displays a decreased capacity to use non-haem iron sources in vitro, a growth defect in a low iron medium that is enhanced at pH 6, and studies employing radiolabelled FeCl3 confirmed that FtrABCD transports ferrous iron. Transcription of the ftrA gene is induced in B. abortus 2308 in response to iron deprivation and exposure to acid pH, and similar to other Brucella iron acquisition genes that have been examined the iron-responsiveness of ftrA is dependent upon the iron response regulator Irr. The B. abortus ftrA mutant exhibits significant attenuation in both cultured murine macrophages and experimentally infected mice, supporting the proposition that ferrous iron is a critical iron source for these bacteria in the mammalian host. © 2013 John Wiley & Sons Ltd.

  17. Bacteria-assisted preparation of nano α-Fe2O3 red pigment powders from waste ferrous sulfate

    International Nuclear Information System (INIS)

    Li, Xiang; Wang, Chuankai; Zeng, Yu; Li, Panyu; Xie, Tonghui; Zhang, Yongkui

    2016-01-01

    Highlights: • A route to prepare nano α-Fe 2 O 3 red pigment from waste ferrous sulfate is proposed. • Acidithiobacillus ferrooxidans is introduced for accelerating iron oxidation. • The particle size of synthetic α-Fe 2 O 3 is ranged from 22 nm to 86 nm. • The prepared nano α-Fe 2 O 3 red pigment fulfills ISO 1248-2006. - Abstract: Massive ferrous sulfate with excess sulfuric acid is produced in titanium dioxide industry each year, ending up stockpiled or in landfills as solid waste, which is hazardous to environment and in urgent demand to be recycled. In this study, waste ferrous sulfate was used as a second raw material to synthesize nano α-Fe 2 O 3 red pigment powders with a bacteria-assisted oxidation process by Acidithiobacillus ferrooxidans. The synthesis route, mainly consisting of bio-oxidation, precipitation and calcination, was investigated by means of titration, thermogravimetric analysis (TGA), X-ray diffraction (XRD), scanning electron microscope (SEM) and X-ray fluorescence (XRF) to obtain optimum conditions. Under the optimum conditions, nano α-Fe 2 O 3 red pigment powders contained 98.24 wt.% of Fe 2 O 3 were successfully prepared, with a morphology of spheroidal and particle size ranged from 22 nm to 86 nm and averaged at 45 nm. Moreover, the resulting product fulfilled ISO 1248-2006, the standards of iron oxide pigments.

  18. RESTRUCTURING OF INDUSTRIAL ENTERPRISE

    Directory of Open Access Journals (Sweden)

    L. I. Podderegina

    2009-01-01

    Full Text Available The paper presents main principles for execution of current and strategic restructuring of national enterprises while using experience of countries with developed market economy. The principles contribute to higher efficiency in internal industrial relations at national industrial enterprises.

  19. The effect of initial pH on the kinetics of ferrous-iron biooxidation at ...

    African Journals Online (AJOL)

    The general understanding in bioleaching of sulphide minerals is to keep pH low. A number of published articles have reported the effect of pH on biooxidation rates of ferrous-iron and/or sulphur by bioleaching microbes, although most of these studies were conducted at optimum or near optimum temperature for microbial ...

  20. Molecular characterization of whey protein hydrolysate fractions with ferrous chelating and enhanced iron solubility capabilities.

    Science.gov (United States)

    O'Loughlin, Ian B; Kelly, Phil M; Murray, Brian A; FitzGerald, Richard J; Brodkorb, Andre

    2015-03-18

    The ferrous (Fe2+) chelating capabilities of WPI hydrolysate fractions produced via cascade membrane filtration were investigated, specifically 1 kDa permeate (P) and 30 kDa retentate (R) fractions. The 1 kDa-P possessed a Fe2+ chelating capability at 1 g L(-1) equivalent to 84.4 μM EDTA (for 30 kDa-R the value was 8.7 μM EDTA). Fourier transformed infrared (FTIR) spectroscopy was utilized to investigate the structural characteristics of hydrolysates and molecular interactions with Fe2+. Solid-phase extraction was employed to enrich for chelating activity; the most potent chelating fraction was enriched in histidine and lysine. The solubility of ferrous sulfate solutions (10 mM) over a range of pH values was significantly (Piron solubility was improved by 72% in the presence of the 1 kDa-P fraction following simulated gastrointestinal digestion (SGID) compared to control FeSO4·7H2O solutions.

  1. Chemistry and metallurgy in the Portuguese Empire

    Energy Technology Data Exchange (ETDEWEB)

    Habashi, F. [Laval Univ., Sainte-Foy, Quebec City, PQ (Canada)

    2000-10-01

    The foundation and expansion of the Portuguese Empire is sketched, with emphasis on the development of a new type of ship by Prince Henrique the Navigator (AD 1385-1460), known as the caravel. By virtue of its advanced design, it was capable of sailing the stormy seas at high speeds, and thereby was instrumental in extending Portuguese influence over vast territories in South America, Asia and Africa, extending Portuguese know-how in mining, metallurgy, chemistry and trade along with Christianity. The role played by the University of Coimbra, founded in 1306, and the contribution of the Brazilian Geological Survey, established in 1875, and of the School of Mines in Ouro Preto in Brazil in 1876, in the exploitation of the mineral wealth of the Portuguese colonies is chronicled.

  2. Enterprise Social Media

    DEFF Research Database (Denmark)

    Khajeheian, Datis

    2018-01-01

    This article reports an ethnographic research on effect of enterprise social media on communication of members in entrepreneurial teams. The researcher acted as an entrepreneur and as a team member in two entrepreneurial projects to observe the communication of team members within the enterprise...... social media. In addition to observation, he conducted some interviews with team members to collect supplementary data. A theoretical framework developed from an array of three metaphors: leaky pipe, echo chamber and social lubricant, and four organizational learning processes: social capital, boundary...... work, attention allocation and social analytics. By the interpretation of the collected data, a new metaphor of “living room” was proposed. This metaphor suggests that enterprise social media provide a space for interaction of internal-external people similar to what home members and guests do...

  3. Management by the value of enterprise

    Directory of Open Access Journals (Sweden)

    M. V. Zenkinа

    2017-01-01

    Full Text Available The management of the enterprise's value is largely aimed at increasing the investment attractiveness of the enterprise. The search for new methods and techniques for managing the property complex faces a number of problems that are a promise of developing scientific approaches to the development of new progressive methods of making managerial decisions. The article considers alternative options for improving the quality of enterprise management and suggests the direction of improving the organization’s cost management system. A number of limiting factors, which allowed the author to determine the target indicators of the presented model, determines the presented objective function of enterprise value. It is permissible to change and expand the composition of the indicators and the approaches used to assess the value of the enterprise. The recommended model allows determining the reserves of increasing the efficiency of the enterprise, affecting the value of the property complex. Dependence of the singled out evaluation criteria and the targets of strategies for increasing the value of enterprises is indicated. The main stages of the enterprise value management process are considered as a single concept of increasing the current value of the organization. The characteristic of the concept of management aimed at creating value – Value Based Management (VBM is presented. The main principles of VBM aimed at qualitative improvement of strategic and operational decisions at all levels of management of the organization are singled out. Article considers the technology of introducing a cost management system based on the example of a construction organization. The main stages of enterprise cost management aimed at long-term sustainable growth in the value of the organization are identified. Particular attention is paid to the stages of analysis of the contribution of production and management units to the total value of the enterprise and the

  4. 78 FR 46295 - Enterprise Underwriting Standards

    Science.gov (United States)

    2013-07-31

    ... 2590-AA53 Enterprise Underwriting Standards AGENCY: Federal Housing Finance Agency. ACTION: Proposed...), (together, the Enterprises) relating to mortgage assets affected by Property Assessed Clean Energy (PACE... that were encumbered by this retrofit lending program that created a priority ahead of the Enterprise...

  5. Challenges and solutions in enterprise computing

    NARCIS (Netherlands)

    van Sinderen, Marten J.

    2008-01-01

    The emergence of the networked enterprise has a profound effect on enterprise computing. This introduction discusses some important challenges in enterprise computing, which are the result of the mentioned networking trend, and positions the articles of this special issue with respect to these

  6. How does Enterprise Architecture support innovation?

    DEFF Research Database (Denmark)

    Nardello, Marco; Lapalme, James; Toppenberg, Gustav

    2015-01-01

    Innovation is becoming increasingly important for Enterprise Architecture (EA) teams. Consequently, it is crucial that tools be developed to assist Enterprise Architecture teams when evaluating how (and how well) they are supporting innovation within the context of their enterprise. To date very...

  7. Survey of Micro Enterprise.

    Science.gov (United States)

    European Social Fund, Dublin (Ireland).

    Government support of microenterprise/entrepreneurship in Ireland was examined through structured interviews with 81 of 120 microentrepreneurs (68% response rate) identified as clients of local enterprise support agencies and/or completers of enterprise training and structured interviews with representatives of 25 local, voluntary, and private…

  8. Protonation of Ferrous Dinitrogen Complexes Containing a Diphosphine Ligand with a Pendant Amine

    Energy Technology Data Exchange (ETDEWEB)

    Heiden, Zachariah M.; Chen, Shentan; Mock, Michael T.; Dougherty, William G.; Kassel, W. S.; Rousseau, Roger J.; Bullock, R. Morris

    2013-04-01

    The addition of protons to pendant amine containing ferrous dinitrogen complexes, of the type [FeX(N2)(PEtNMePEt)(dmpm)]+ (X = H, Cl, or Br; PEtNMePEt = Et2PCH2N(Me)CH2PEt2 and dmpm = Me2PCH2PMe2), was found to protonate at the pendant amine as opposed to the dinitrogen ligand. This protonation increased the νN2 of the complex by about 25 cm-1, shifting the Fe(II/I) couple 330 mV to a more positive potential. A similar shift was observed in the case of [FeX(CO)(PEtNMePEt)(dmpm)]+ (X = H, Cl, or Br). Computational analysis verified these experimental results and showed the coordination of N2 to Fe(II) centers increases the basicity of N2 (vs. free N2) by 13 and 20 pKa units for the trans halides and hydrides, respectively. Although the iron center was found to increase the basicity of the bound N2 ligand, coordinated N2 is not sufficiently basic to be protonated. In the case of ferrous dinitrogen complexes containing a basic pendant methylamine, the amine site was determined to be the most basic site by 30 pKa units compared to protonation at the N2 ligand. To increase the basicity of the N2 ligand in order to promote proton transfer from the pendant amine to the N2 ligand, chemical reduction of these ferrous dinitrogen complexes was performed and found to result in oxidative addition of the methylene C-H bond of the PEtNMePEt ligand to Fe, preventing isolation of a reduced Fe(0) N2 complex. This work was supported as part of the Center for Molecular Electrocatalysis, an Energy Frontier Research Center funded by the U.S. Department of Energy Office of Science, Office of Basic Energy Sciences.

  9. The Impact of Enterprise Resource Planning Systems on Small and Medium Enterprises

    Science.gov (United States)

    Buleje, Miguel A.

    2014-01-01

    Enterprise resource planning (ERP) systems are considered the price of entry in today's business environment, and the number of small and medium-sized enterprises (SME) retiring legacy systems in favor of ERP systems is increasing exponentially. However, there is a lack of knowledge and awareness of ERP systems and their potential benefit and…

  10. Early Sociology of the Business Enterprise: Max Weber's Theory of the Modern Business Enterprise in Economy and Society

    DEFF Research Database (Denmark)

    Jagd, Søren

    be explained as the unfolding of a sociological theory of the modern business enterprise. Some of the most important features of Weber’s theory of the modern business enterprise are presented. Weber points to the multidimensional institutional embeddedness of the modern business enterprise and to the crucial...... importance of ongoing tensions between formal and substantive rationality. Weber’s theory of the modern business enterprise in chapter 2 of Economy and Society may then be seen as an important but still unexplored early contribution to a sociological theory of the modern business enterprise....

  11. Theoretical Grounds of Enterprise Restructuring

    Directory of Open Access Journals (Sweden)

    Odintsova Nadiya G.

    2013-11-01

    Full Text Available One of the most popular means of financial recovery of enterprises in the world and domestic theory and practice is re-structuring. The article considers the essence of enterprise re-structuring, conducts analysis of existing approaches to understanding the re-organisation, re-formation, re-structuring and re-engineering notions and makes conclusions with respect to the nature of their interconnection. It analyses interpretation of the re-structuring category, approaches of scientists to revelation of the essence of the enterprise re-structuring notion. To achieve the goal the article conducts assessment of the existing approaches to interpretation of the content of the enterprise re-structuring process. It also conducts further analysis of interconnection of the re-formation, re-structuring, re-organisation and re-engineering notions with consideration of scientific interpretations, which would allow identification of the roles of each of the notions for identifying their influence and interconnection in correlation with the direction of economic activity of enterprises.

  12. The marketing strategy of a small enterprise

    OpenAIRE

    Trandafilović Igor

    2008-01-01

    Small enterprise shows some specific characteristics which are necessary for creation of marketing strategy. The goal of this work is an attempt of marketing strategy analysis of the small enterprises. The necessary request of the analysis is to define the small enterprise. There have also been analyzed the specific orders for small enterpriser. Special part of work is dedicated to a small enterprises management strategy and the other one to their marketing communications. There are mentioned...

  13. Elucidating the role of ferrous ion cocatalyst in enhancing dilute acid pretreatment of lignocellulosic biomass

    Directory of Open Access Journals (Sweden)

    Wei Hui

    2011-11-01

    Full Text Available Abstract Background Recently developed iron cocatalyst enhancement of dilute acid pretreatment of biomass is a promising approach for enhancing sugar release from recalcitrant lignocellulosic biomass. However, very little is known about the underlying mechanisms of this enhancement. In the current study, our aim was to identify several essential factors that contribute to ferrous ion-enhanced efficiency during dilute acid pretreatment of biomass and to initiate the investigation of the mechanisms that result in this enhancement. Results During dilute acid and ferrous ion cocatalyst pretreatments, we observed concomitant increases in solubilized sugars in the hydrolysate and reducing sugars in the (insoluble biomass residues. We also observed enhancements in sugar release during subsequent enzymatic saccharification of iron cocatalyst-pretreated biomass. Fourier transform Raman spectroscopy showed that major peaks representing the C-O-C and C-H bonds in cellulose are significantly attenuated by iron cocatalyst pretreatment. Imaging using Prussian blue staining indicated that Fe2+ ions associate with both cellulose/xylan and lignin in untreated as well as dilute acid/Fe2+ ion-pretreated corn stover samples. Analyses by scanning electron microscopy and transmission electron microscopy revealed structural details of biomass after dilute acid/Fe2+ ion pretreatment, in which delamination and fibrillation of the cell wall were observed. Conclusions By using this multimodal approach, we have revealed that (1 acid-ferrous ion-assisted pretreatment increases solubilization and enzymatic digestion of both cellulose and xylan to monomers and (2 this pretreatment likely targets multiple chemistries in plant cell wall polymer networks, including those represented by the C-O-C and C-H bonds in cellulose.

  14. Lactoferrin or ferrous salts for iron deficiency anemia in pregnancy: A meta-analysis of randomized trials.

    Science.gov (United States)

    Abu Hashim, Hatem; Foda, Osama; Ghayaty, Essam

    2017-12-01

    This systematic review and meta-analysis aimed to evaluate the efficacy of daily oral bovine lactoferrin versus daily oral ferrous iron preparations for treatment of iron deficiency anemia (IDA) during pregnancy. Searches were conducted on PubMed, ScienceDirect, ClinicalTrials.gov and CENTRAL databases from inception to February 2017 and the bibliographies of retrieved articles were screened. The PRISMA Statement was followed. Published English language randomized trials comparing lactoferrin with oral ferrous iron preparations in pregnant women with iron deficiency anemia were included. Quasi-randomized, non- randomized or studies including other known cause of anemia, gestational or pre-existent maternal diseases were excluded. Accordingly, 4 eligible trials (600 women) were analyzed. Primary outcome was change in hemoglobin level at 4 weeks of treatment. Secondary outcomes were; change in serum ferritin and iron, rates of gastrointestinal side effects, preterm birth, low birthweight, neonatal death and mean birthweight. Quality assessment was performed by the Cochrane risk of bias tool. Odds ratio and mean difference were used to integrate dichotomous and continuous outcomes respectively. Pooled estimates for change in hemoglobin levels at four weeks favored daily oral lactoferrin over daily oral ferrous sulphate (mean difference 0.77; 95% confidence interval [CI] 0.04-1.55; P=0.04, 4 trials, 600 women). However, after subgroup analysis (degree of anemia), no significant difference in hemoglobin levels were found between both groups in mild anemia (mean difference 0.80; 95% CI -0.21 to 1.82, 3 trials, 372 women), but a significant increase favoring lactoferrin was reported in moderate anemia (mean difference 0.68; 95% CI 0.53-0.83; P<0.00001, one trial, 228 women). Significantly less gastrointestinal side effects were reported with lactoferrin treatment. No significant differences existed with regard to other outcomes. In conclusion, for pregnant women with IDA

  15. Stakeholder Analysis To Shape the Enterprise

    Science.gov (United States)

    McCaughin, Keith; Derosa, Joseph

    An enterprise is a complex adaptive social system that should maximize stakeholder, not shareholder, value — value to employees, customers, shareholders and others. We expand upon Russell Ackoff s direction to distribute value among stakeholders, to propose a schema of rules that guide the interactions among autonomous agents in the transactional environment of an enterprise. We define an enterprise as an organization and its transactional environment interacting with and adapting to each other. Enterprise behavior can only be understood in the context of this transactional environment where everything depends on everything else and interactions cannot be controlled, but can be influenced if they are guided by an understanding of the internal rules of the autonomous agents. The schema has four complementary rules (control, autonomy, return and value) derived from the work of Russell Ackoff and Michael Porter. The basic rules are applied in combination to eight stakeholder types derived from Richard Hopeman and Raymond McLeod (Leaders, Competitors, Customers, Public, Workers, Collaborators, Suppliers and Regulators). An enterprise can use this schema and rules in a process of stakeholder analysis to develop and continually refine strategies to encourage behaviors that benefit the enterprise and discourage behaviors that harm the enterprise. These strategies are implemented in a relationship management program in support of enterprise strategic management to consciously and explicitly shape the environment to reduce risks and increase opportunities for success.

  16. 25 CFR 286.7 - Location of enterprise.

    Science.gov (United States)

    2010-04-01

    ... 25 Indians 1 2010-04-01 2010-04-01 false Location of enterprise. 286.7 Section 286.7 Indians BUREAU OF INDIAN AFFAIRS, DEPARTMENT OF THE INTERIOR ECONOMIC ENTERPRISES INDIAN BUSINESS DEVELOPMENT PROGRAM § 286.7 Location of enterprise. To be eligible for a grant an economic enterprise must be located...

  17. Oxidation of adsorbed ferrous iron: kinetics and influence of process conditions.

    Science.gov (United States)

    Buamah, R; Petrusevski, B; Schippers, J C

    2009-01-01

    For the removal of iron from groundwater, aeration followed with rapid (sand) filtration is frequently applied. Iron removal in this process is achieved through oxidation of Fe(2 + ) in aqueous solution followed by floc formation as well as adsorption of Fe(2 + ) onto the filter media. The rate of oxidation of the adsorbed Fe(2 + ) on the filter media plays an important role in this removal process. This study focuses on investigating the effect of pH on the rate of oxidation of adsorbed Fe(2 + ). Fe(2 + ) has been adsorbed, under anoxic conditions, on iron oxide coated sand (IOCS) in a short filter column and subsequently oxidized by feeding the column with aerated water. Ferrous ions adsorbed at pH 5, 6, 7 and 8 demonstrated consumption of oxygen, when aerated water was fed into the column. The oxygen uptake at pH 7 and 8 was faster than at pH 5 and 6. However the difference was less pronounced than expected. The difference is attributed to the pH buffering effect of the IOCS. At feedwater pH 5, 6 and 7 the pH in the effluent was higher than in the influent, while a pH drop should occur because of oxidation of adsorbed Fe(2 + ). At pH 8, the pH dropped. These phenomena are attributed to the presence of calcium and /or ferrous carbonate in IOCS.

  18. It's Entrepreneurship, not Enterprise

    DEFF Research Database (Denmark)

    Hjorth, Daniel; Holt, Robin

    2016-01-01

    We challenge the obvious and easy association of enterprise and entrepreneurship. We do so by arguing that entrepreneurship is inherently social and collective, something that is concealed when held up as example of enterprising behaviour. We use as an illustrative case the Chinese artist Ai Weiwei...

  19. Empowerment Zones and Enterprise Districts, Enterprise Zones: Boundaries of Maryland's Enterprise Districts that are within Washington County., Published in 2006, 1:7200 (1in=600ft) scale, Washington County Government.

    Data.gov (United States)

    NSGIC Local Govt | GIS Inventory — Empowerment Zones and Enterprise Districts dataset current as of 2006. Enterprise Zones: Boundaries of Maryland's Enterprise Districts that are within Washington...

  20. Recommendations and best practices for cloud enterprise security

    OpenAIRE

    Ramachandran, M; Chang, V

    2015-01-01

    © 2014 IEEE. Enterprise security is essential to achieve global information security in business and organizations. Enterprise Cloud computing is a new paradigm for that enterprise where businesses need to be secured. Enterprise Cloud computing has established its businesses and software as a service paradigm is increasing its demand for more services. However, this new trend needs to be more systematic with respect to Enterprise Cloud security. Enterprise Cloud security is the key factor in ...

  1. Physical metallurgy: Scientific school of the Academician V.M. Schastlivtsev

    Science.gov (United States)

    Tabatchikova, T. I.

    2016-04-01

    This paper is to honor Academician Vadim Mikhailovich Schastlivtsev, a prominent scientist in the field of metal physics and materials science. The article comprises an analysis of the topical issues of the physical metallurgy of the early 21st century and of the contribution of V.M. Schastlivtsev and of his school to the science of phase and structural transformations in steels. In 2015, Vadim Mikhailovich celebrates his 80th birthday, and this paper is timed to this honorable date. The list of his main publications is given in it.

  2. State Enterprise Zone Programs: Have They Worked?

    Science.gov (United States)

    Peters, Alan H.; Fisher, Peter S.

    The effectiveness of state enterprise zone programs was examined by using a hypothetical-firm model called the Tax and Incentives Model-Enterprise Zones (TAIM-ez) model to analyze the value of enterprise zone incentives to businesses across the United States and especially in the 13 states that had substantial enterprise zone programs by 1990. The…

  3. Do "Some" Enterprise Zones Create Jobs?

    Science.gov (United States)

    Kolko, Jed; Neumark, David

    2010-01-01

    We study how the employment effects of enterprise zones vary with their location, implementation, and administration, based on evidence from California. We use new establishment-level data and geographic mapping methods, coupled with a survey of enterprise zone administrators. Overall, the evidence indicates that enterprise zones do not increase…

  4. 2008 Enterprise Transition Plan (ETP)

    National Research Council Canada - National Science Library

    England, Gordon

    2008-01-01

    The Enterprise Transition Plan (ETP) is the Department of Defense's integrated business transformation plan, which incorporates the transition plans of the Military Services, Components and the DoD Enterprise...

  5. Integration of environmental approaches to strategy of production enterprises - environmentally oriented quality of production

    Directory of Open Access Journals (Sweden)

    Michalíková Františka

    2001-12-01

    Full Text Available In the paper there are presented system approaches, applied in Slovak transformed production enterprises, which solve questions of closing the so called industrial cycle from the side of the wastes' producers. The production quality is connected not only with the technological chain itself and with outputs from it - the utility product, but also with the load of the life environment.The presented possibilities of the liquidation of solid energetic waste – fly ashes – represent a an overview of forms and methods of its utilization. By combusting one kind of coal in various boilers, fly ashes with different physical, chemical, and mineralogical properties originate, with the combustion temperature as a dominant factor. The fly ashes are directly (without influencing its composition applied in civil engineering, mining, metallurgy, waste water cleaning, etc. Their utilization after a separation removal of unwanted components is an economically difficult process. Such a unvaluable component is coal combustion residue, evaluated by the annealing loss (carbon-in-ash loss in fly ashes used for special procedures in civil enginering, e.g. in mortars (maximally 4% of c.a.s. loss or in the porous concrete (4-7% of c.a.s. loss. The building industry processes about 20% of solid energetic waste.

  6. Information Systems at Enterprise. Design of Secure Network of Enterprise

    Science.gov (United States)

    Saigushev, N. Y.; Mikhailova, U. V.; Vedeneeva, O. A.; Tsaran, A. A.

    2018-05-01

    No enterprise and company can do without designing its own corporate network in today's information society. It accelerates and facilitates the work of employees at any level, but contains a big threat to confidential information of the company. In addition to the data theft attackers, there are plenty of information threats posed by modern malware effects. In this regard, the computational security of corporate networks is an important component of modern information technologies of computer security for any enterprise. This article says about the design of the protected corporate network of the enterprise that provides the computers on the network access to the Internet, as well interoperability with the branch. The access speed to the Internet at a high level is provided through the use of high-speed access channels and load balancing between devices. The security of the designed network is performed through the use of VLAN technology as well as access lists and AAA server.

  7. Towards an enterprise interoperability framework

    CSIR Research Space (South Africa)

    Kotzé, P

    2010-06-01

    Full Text Available This paper presents relevant interoperability approaches and solutions applied to global/international networked (collaborative) enterprises or organisations and conceptualise an enhanced enterprise interoperability framework. The paper covers...

  8. [Severe toxic liver failure after acute poisoning with paracetamol, ferrous sulphate and naproxen].

    Science.gov (United States)

    Adamek, Robert; Wilczek, Lech; Krupiński, Bogusław

    2004-01-01

    We present the case of 20-year-old woman intoxicated with mixed drugs, composed of paracetamol (acetaminophen), ferrous sulphate, naproxen and benzodiazepines. Acute toxic liver damage with clinical symptoms of coma resolved at the patient. Lack of the past history doesn't let to specific therapy and systemic complications. In this data we confirm, that past history, clinical symptoms and laboratory results are needed in designing a treatment strategy.

  9. Means to rise stability of matrices for hot pressing of non-ferrous metals

    International Nuclear Information System (INIS)

    Nagajtsev, A.A.; Piguzova, D.Kh.; Vajnpres, L.V.

    1975-01-01

    The paper deals with the basic trends adopted both in the USSR and abroad with respect to the development and industrial usage of new materials for hot pressing dies. Methods of their strengthening are also indicated. The paper presents results of production tests of new die steels and refractory alloys at a number of factories processing non-ferrous metals. The problems of their wide application in this field are considered

  10. Evaluating Enterprise Education: Why Do It?

    Science.gov (United States)

    Edwards, Louise-Jayne; Muir, Elizabeth J.

    2012-01-01

    Purpose: The purpose of this paper is to argue that evaluations of enterprise education need to develop beyond the economist viewpoint of business start-up and business growth and promote the notion that evaluations of enterprise education should encompass prime pedagogical objectives of enterprise education, enabling students to grow and develop…

  11. Radiation effects in high-disperse metal media and their application in powder metallurgy

    International Nuclear Information System (INIS)

    Zaykin, Y.A.; Aliyev, B.A.

    2002-01-01

    Experimental and theoretical results showing up effects of metal powder radiation processing, such as powder grinding, chemical refinement, and changes in powder particle surface state, are discussed. It is shown that preliminary irradiation of metal powders leads to profound structural alterations at all further stages of their processing by conventional methods of powder metallurgy and eventually effects the properties of the resulting product

  12. Coal mine enterprise integration based on strategic alliance

    Energy Technology Data Exchange (ETDEWEB)

    Zhou, Q.; Sun, J.; Xu, S. [Tsinghua University, Beijing (China). Dept. of Computer Science and Technology

    2003-07-01

    The relationship between coal mine and related enterprise was analysed. Aiming at the competitive world market as well as the dynamic requirement, a coal mine enterprise integration strategy and a enterprise strategic alliance were proposed for the product providing service business pattern. The modelling method of the enterprise strategic alliance was proposed, including the relationship view model, information view model and business process view model. The idea of enterprise strategic alliance is useful for enterprise integration. 6 refs., 2 figs.

  13. Relation of average and highest solvent vapor concentrations in workplaces in small to medium enterprises and large enterprises.

    Science.gov (United States)

    Ukai, Hirohiko; Ohashi, Fumiko; Samoto, Hajime; Fukui, Yoshinari; Okamoto, Satoru; Moriguchi, Jiro; Ezaki, Takafumi; Takada, Shiro; Ikeda, Masayuki

    2006-04-01

    The present study was initiated to examine the relationship between the workplace concentrations and the estimated highest concentrations in solvent workplaces (SWPs), with special references to enterprise size and types of solvent work. Results of survey conducted in 1010 SWPs in 156 enterprises were taken as a database. Workplace air was sampled at > or = 5 crosses in each SWP following a grid sampling strategy. An additional air was grab-sampled at the site where the worker's exposure was estimated to be highest (estimated highest concentration or EHC). The samples were analyzed for 47 solvents designated by regulation, and solvent concentrations in each sample were summed up by use of additiveness formula. From the workplace concentrations at > or = 5 points, geometric mean and geometric standard deviations were calculated as the representative workplace concentration (RWC) and the indicator of variation in workplace concentration (VWC). Comparison between RWC and EHC in the total of 1010 SWPs showed that EHC was 1.2 (in large enterprises with>300 employees) to 1.7 times [in small to medium (SM) enterprises with enterprises and large enterprises, both RWC and EHC were significantly higher in SM enterprises than in large enterprises. Further comparison by types of solvent work showed that the difference was more marked in printing, surface coating and degreasing/cleaning/wiping SWPs, whereas it was less remarkable in painting SWPs and essentially nil in testing/research laboratories. In conclusion, the present observation as discussed in reference to previous publications suggests that RWC, EHC and the ratio of EHC/WRC varies substantially among different types of solvent work as well as enterprise size, and are typically higher in printing SWPs in SM enterprises.

  14. Innovativeness of enterprises in Poland

    Directory of Open Access Journals (Sweden)

    Katarzyna Sieradzka

    2013-01-01

    Full Text Available At a time of huge economic challenges, innovativeness is perceived as a way of overcoming difficulties, fostering and assuring socio-economic growth of particular countries. It is necessary to improve competitive standing of enterprises both in domestic and international economies. Launching of new or improved products, application of state of the art technologies and of new organisational and management solutions are key to enhanced effectiveness and better competitiveness of enterprises. Innovation standards of Polish enterprises are considerably lower than those of businesses operating in countries of the old European Union, therefore so much attention is paid to these issues.This paper undertakes to analyse innovative activities of enterprises in the Polish economy.Based on the report ‘Innovation Union Scoreboard’, a comparative analysis of Poland’s innovation standards in relation to other member states of the European Union is conducted, levels and structure of financial spending on innovative activities incurred by Polish industrial enterprises are discussed using statistics published by the National Office for Statistics and Ministry of Economy.

  15. Enterprise 3.0 in Engineering Education

    Science.gov (United States)

    Ahrens, Andreas; Zascerinska, Jelena

    2011-01-01

    Enterprise 3.0 offers potential solutions for the quality, maintenance and sustainable development of services. The synergy between Enterprise 3.0 and engineering education advances the development of innovative products, processes and services in the European economy. Aim of the research is to analyze student engineers' use of Enterprise 3.0…

  16. Information Resources Management Framework for Virtual Enterprise

    OpenAIRE

    Mao, Lingxiang

    2015-01-01

    Virtual enterprise is a new form of organization in recent years which adapt to the IT environment. Information resources management implemented in the virtual enterprise is determined by the form of business organization and information exchange mechanisms. According to the present characteristics of virtual enterprise management, it puts forward the strategies and measures of information resources management framework for virtual enterprise.

  17. INFORMATION SYSTEM STRATEGIC PLANNING WITH ENTERPRISE ARCHITECTURE PLANNING

    Directory of Open Access Journals (Sweden)

    Lola Yorita Astri

    2013-05-01

    Full Text Available An integrated information system is needed in an enterprise to support businessprocesses run by an enterprise. Therefore, to develop information system can use enterprisearchitecture approach which can define strategic planning of enterprise information system. SMPNegeri 1 Jambi can be viewed as an enterprise because there are entities that should be managedthrough an integrated information system. Since there has been no unification of different elementsin a unity yet, enterprise architecture model using Enterprise Architecture Planning (EAP isneeded which will obtain strategic planning of enterprise information system in SMP Negeri 1Jambi. The goal of strategic planning of information system with Enterprise Architecture Planning(EAP is to define primary activities run by SMP Negeri 1 Jambi and support activities supportingprimary activities. They can be used as a basis for making data architecture which is the entities ofapplication architecture. At last, technology architecture is designed to describe technology neededto provide environment for data application. The plan of implementation is the activity plan madeto implemented architectures by enterprise.

  18. Powder metallurgy preparation of Al-Cu-Fe quasicrystals using mechanical alloying and Spark Plasma Sintering

    Czech Academy of Sciences Publication Activity Database

    Novák, P.; Kubatík, Tomáš František; Vystrčil, J.; Hendrych, R.; Kříž, J.; Mlynár, J.; Vojtěch, D.

    2014-01-01

    Roč. 52, September (2014), s. 131-137 ISSN 0966-9795 Institutional support: RVO:61389021 Keywords : Nanostructure intermetallics * Ternary alloys systems * Mechanical alloying and milling * Sintering * Diffraction Subject RIV: JG - Metallurgy Impact factor: 2.131, year: 2014 http://www.sciencedirect.com/science/article/pii/S0966979514001198#

  19. Force.com enterprise architecture

    CERN Document Server

    Fawcett, Andrew

    2014-01-01

    This book is for advanced Force.com developers and architects who need to understand the Salesforce platform from the perspective of enterprise-level requirements. You should have an existing understanding of Apex and Visualforce. Those familiar with other enterprise software ecosystems will also find this book ideal as they adopt Force.com.

  20. Friction and surface chemistry of some ferrous-base metallic glasses

    Science.gov (United States)

    Miyoshi, K.; Buckley, D. H.

    1982-01-01

    The friction properties of some ferrous-base metallic glasses were measured both in argon and in vacuum to a temperature of 350 C. The alloy surfaces were also analyzed with X-ray photoelectron spectroscopy to identify the compounds and elements present on the surface. The results of the investigation indicate that even when the surfaces of the amorphous alloys, or metallic glasses, are atomically clean, bulk contaminants such as boric oxide and silicon dioxide diffuse to the surfaces. Friction measurements in both argon and vacuum indicate that the alloys exhibit higher coefficients of friction in the crystalline state than they do in the amorphous state.

  1. Locally-Based Enterprise Training To Improve The Economic Empowerment Of The Learners Of Independent Enterprise Literacy

    Directory of Open Access Journals (Sweden)

    Dayat Hidayat

    2016-12-01

    Full Text Available Entrepreneurial skills of learners of Independent Enterprise Literacy at Community Learning Center (CLC Harapan Karawang Regency in developing locally-based enterprise, is still low. This study is aimed to analyze the planning, the implementation, the outcome, and the impact of locally-based enterprise training on improving the economic empowerment of the learners of Independent Enterprise Literacy. The approach uses in this study is a qualitative case study method. The subjects consist of four learners, a trainer, and an administrator of CLC. The data are obtained through the observation, in-depth interview, and documentation analysis. The data analysis involves the following stages: data collection, data reduction, data display, and conclusion drawing/verification. The locally-based enterprise training is designed through proper planning with the identification of learner needs, formulating objectives and preparing training curriculum that meets the needs and characteristics of the learners. The implementation of the training is conducted properly in accordance with a predetermined plan. The results of training assessment show an increase of knowledge, attitudes and behavior of learners’ entrepreneurial skills. The enterprise training gives impact and influence to increase the learners’ economic empowerment proved by the increasing income and wider business opportunities.

  2. Summary of NRC LWR safety research programs on fuel behavior, metallurgy/materials and operational safety

    International Nuclear Information System (INIS)

    Bennett, G.L.

    1979-09-01

    The NRC light-water reactor safety-research program is part of the NRC regulatory program for ensuring the safety of nuclear power plants. This paper summarizes the results of NRC-sponsored research into fuel behavior, metallurgy and materials, and operational safety. The fuel behavior research program provides a detailed understanding of the response of nuclear fuel assemblies to postulated off-normal or accident conditions. Fuel behavior research includes studies of basic fuel rod properties, in-reactor tests, computer code development, fission product release and fuel meltdown. The metallurgy and materials research program provides independent confirmation of the safe design of reactor vessels and piping. This program includes studies on fracture mechanics, irradiation embrittlement, stress corrosion, crack growth, and nondestructive examination. The operational safety research provides direct assistance to NRC officials concerned with the operational and operational-safety aspects of nuclear power plants. The topics currently being addressed include qualification testing evaluation, fire protection, human factors, and noise diagnostics

  3. Development of new metal matrix composite electrodes for electrical discharge machining through powder metallurgy process

    Directory of Open Access Journals (Sweden)

    C. Mathalai Sundaram

    2014-12-01

    Full Text Available Electrical discharge machining (EDM is one of the widely used nontraditional machining methods to produce die cavities by the erosive effect of electrical discharges. This method is popular due to the fact that a relatively soft electrically conductive tool electrode can machine hard work piece. Copper electrode is normally used for machining process. Electrode wear rate is the major drawback for EDM researchers. This research focus on fabrication of metal matrix composite (MMC electrode by mixing copper powder with titanium carbide (TiC and Tungsten carbide (WC powder through powder metallurgy process, Copper powder is the major amount of mixing proportion with TiC and WC. However, this paper focus on the early stage of the project where powder metallurgy route was used to determine suitable mixing time, compaction pressure and sintering and compacting process in producing EDM electrode. The newly prepared composite electrodes in different composition are tested in EDM for OHNS steel.

  4. Job Stress in the United Kingdom: Are Small and Medium-Sized Enterprises and Large Enterprises Different?

    Science.gov (United States)

    Lai, Yanqing; Saridakis, George; Blackburn, Robert

    2015-08-01

    This paper examines the relationships between firm size and employees' experience of work stress. We used a matched employer-employee dataset (Workplace Employment Relations Survey 2011) that comprises of 7182 employees from 1210 private organizations in the United Kingdom. Initially, we find that employees in small and medium-sized enterprises experience lower level of overall job stress than those in large enterprises, although the effect disappears when we control for individual and organizational characteristics in the model. We also find that quantitative work overload, job insecurity and poor promotion opportunities, good work relationships and poor communication are strongly associated with job stress in the small and medium-sized enterprises, whereas qualitative work overload, poor job autonomy and employee engagements are more related with larger enterprises. Hence, our estimates show that the association and magnitude of estimated effects differ significantly by enterprise size. Copyright © 2013 John Wiley & Sons, Ltd.

  5. A survivability model for ejection of green compacts in powder metallurgy technology

    Directory of Open Access Journals (Sweden)

    Payman Ahi

    2012-01-01

    Full Text Available Reliability and quality assurance have become major considerations in the design and manufacture of today’s parts and products. Survivability of green compact using powder metallurgy technology is considered as one of the major quality attributes in manufacturing systems today. During powder metallurgy (PM production, the compaction conditions and behavior of the metal powder dictate the stress and density distribution in the green compact prior to sintering. These parameters greatly influence the mechanical properties and overall strength of the final component. In order to improve these properties, higher compaction pressures are usually employed, which make unloading and ejection of green compacts more challenging, especially for the powder-compacted parts with relatively complicated shapes. This study looked at a mathematical survivability model concerning green compact characteristics in PM technology and the stress-strength failure model in reliability engineering. This model depicts the relationship between mechanical loads (stress during ejection, experimentally determined green strength and survivability of green compact. The resulting survivability is the probability that a green compact survives during and after ejection. This survivability model can be used as an efficient tool for selecting the appropriate parameters for the process planning stage in PM technology. A case study is presented here in order to demonstrate the application of the proposed survivability model.

  6. The stress-corrosion cracking behavior of high-strength aluminum powder metallurgy alloys

    Science.gov (United States)

    Pickens, J. R.; Christodoulou, L.

    1987-01-01

    The susceptibility to stress-corrosion cracking (SCC) of rapidly solidified (RS) aluminum powder metallurgy (P/M) alloys 7090 and 7091, mechanically alloyed aluminum P/M alloy IN* 9052, and ingot metallurgy (I/M) alloys of similar compositions was compared using bolt-loaded double cantilever beam specimens. In addition, the effects of aging, grain size, grain boundary segregation, pre-exposure embrittlement, and loading mode on the SCC of 7091 were independently assessed. Finally, the data generated were used to elucidate the mechanisms of SCC in the three P/M alloys. The IN 9052 had the lowest SCC susceptibility of all alloys tested in the peak-strength condition, although no SCC was observed in the two RS alloys in the overaged condition. The susceptibility of the RS alloys was greater in the underaged than the peak-aged temper. We detected no significant differences in susceptibility of 7091 with grain sizes varying from 2 to 300 μm. Most of the crack advance during SCC of 7091 was by hydrogen embrittlement (HE). Furthermore, both RS alloys were found to be susceptible to preexposure embrittlement—also indicative of HE. The P/M alloys were less susceptible to SCC than the I/M alloys in all but one test.

  7. Degradation of trichloroethylene in aqueous solution by calcium peroxide activated with ferrous ion.

    Science.gov (United States)

    Zhang, Xiang; Gu, Xiaogang; Lu, Shuguang; Miao, Zhouwei; Xu, Minhui; Fu, Xiaori; Qiu, Zhaofu; Sui, Qian

    2015-03-02

    The application of calcium peroxide (CaO2) activated with ferrous ion to stimulate the degradation of trichloroethylene (TCE) was investigated. The experimental results showed that TCE could be completely degraded in 5 min at a CaO2/Fe(II)/TCE molar ratio of 4/8/1. Probe compound tests demonstrated the presence of reactive oxygen species HO· and O2(-·) in CaO2/Fe(II) system, while scavenging tests indicated that HO· was the dominant active species responsible for TCE removal, and O2(-·) could promote TCE degradation in CaO2/Fe(II) system. In addition, the influences of initial solution pH and solution matrix were evaluated. It suggested that the elevation of initial solution pH suppressed TCE degradation. Cl(-) had significant scavenging effect on TCE removal, whereas HCO3(-) of high concentration showed favorable function. The influences of NO3(-) and SO4(2-) could be negligible, while natural organic matter (NOM) had a negative effect on TCE removal at a relatively high concentration. The results demonstrated that the technique of CaO2 activated with ferrous ion is a highly promising technique in in situ chemical oxidation (ISCO) remediation in TCE contaminated sites. Copyright © 2014. Published by Elsevier B.V.

  8. Export constraints facing Lesotho-based manufacturing enterprises

    Directory of Open Access Journals (Sweden)

    Motšelisi C. Mokhethi

    2015-07-01

    Full Text Available Orientation: Exporting is preferred by many enterprises as the mode of foreign entry as it requires less commitment of organisational resources and offers flexibility of managerial actions. However, enterprises face a number of challenges when attempting to initiate exports or expand their export operations. Research purpose: This study was undertaken to determine the characteristics and composition of export barriers constraining exporting by Lesotho-based manufacturing enterprises. Motivation for the study: Lesotho is faced with low destination diversity and low diversity in export products. Research design, approach and method: Data was collected from 162 Lesotho-based manufacturing enterprises through a self-administered questionnaire. Main findings: In its findings, the study firstly identified international constraints, distribution constraints and financial constraints as factors constraining exporting. Secondly, it was determined that three exporting constraints, all internal to the enterprise and all related to one factor (namely financial constraint hampered exporting. Lastly, the ANOVA results revealed that the perceptions of export constraints differed according to the enterprise characteristics, enterprise size, ownership and type of industry. Contribution/value-add: With the majority of enterprises in this study being identified as micro-enterprises, the government of Lesotho needs to pay particular attention to addressing the export needs of these enterprises in order to enable them to participate in exporting activities − especially considering that they can play a pivotal role in the alleviation of poverty, job creation and economic rejuvenation.

  9. Analytic study of the capital restructuring processes in metallurgical enterprises around the world and in Poland

    Directory of Open Access Journals (Sweden)

    B. Gajdzik

    2012-04-01

    Full Text Available The article presents the most common directions of changes in capital groups in the sector of metallurgy around the world and in Poland. During the observation of the restructuring activities in metallurgy the attention was turned to the integration of the capital groups, capital outsourcing and contract outsourcing, creation and the takeover of the dependent companies. The meaning of the capital consolidation was underlined on the global metallurgy market in order to gain competitive advantage through the increase of manufacturing capacity. The overview of the rating of the global steel producers in years 1989-2009 was conducted with this article in mind and it has shown the changes in the participation of particular capital groups in the world production of steel.

  10. Enterprise Education as Pedagogy

    Science.gov (United States)

    Jones, Brian; Iredale, Norma

    2010-01-01

    Purpose: This paper seeks to suggest that the most appropriate way to construe the concept of enterprise education is from a pedagogical viewpoint. Enterprise education as pedagogy is argued to be the most appropriate way to think about the concept and serves to demarcate it from entrepreneurship education, which is very much about business…

  11. Microstructural and electrical investigation of Cu-Ni-Cr alloys obtained by powder metallurgy method

    International Nuclear Information System (INIS)

    Carrio, Juan A.G.; Carvalhal, M.A.; Ayabe, L.M.; Monteiro, W.A.

    2009-01-01

    The aim of this work, using the powder metallurgy process, is to synthesize metallic alloys with high mechanical strength and high electric conductivity, after melting optimizing and thermal treatments. The Cu-Ni-Cr (wt%) alloys are characterized in their mechanical and electrical properties as well as the obtained microstructure. Through the process of powder metallurgy, contacts and structural parts can be obtained. The alloys elements are added to copper with the intention to improve their strength, ductility and thermal stability, without causing considerable damages in their form, electrical and thermal conductivity, and corrosion resistance. The metallic powders were mixed for a suitable time and then they were pressed in a cold uniaxial pressing (1000 kPa). Afterwards, the specimens were sintered in temperatures varying from 700 up to 800 deg C under vacuum. At last, the samples were homogenized at 550 deg C under vacuum, for special times. The comparative analysis is based on the sintered density, densification parameter, hardness, macrostructures and microstructures of the samples. The alloys were characterized by optical microscopy, X-rays powder diffraction, electrical conductivity and Vickers hardness. (author)

  12. Formation of e-Enterprise; e-entapuraizu no keisei

    Energy Technology Data Exchange (ETDEWEB)

    Komatsu, S. [Nagoya Univ. of Commerce and Business Administration, Nagoya (Japan)

    2000-12-05

    In the first term of appearance of internet, it did not differ from ordinary issuances which customers read texts or see images. Internet is used as a novel business model (B-to-C) designed for the purpose of merchandising between enterprises and consumers. Following models for general consumers, B-to-B business between enterprises appeared. And now, enterprises called e-enterprise integrating B-to-B business models and B-to-C business appeared. While information technology is positioned for assistant support for enterprise activities, but now activities of enterprises itself transferred into cyber-space. (NEDO)

  13. THE TRANSFORMATION OF LAND RESOURCES AND THE SUPPORT OF THE BALANCED LAND USE

    Directory of Open Access Journals (Sweden)

    V. V. Balashenko

    2018-03-01

    Full Text Available The relevance of the study. The degradation, which is a depletion of natural resources, including land resources, actualizes the problem of forecasting the consequences of human activities and assessing the possible economic damage. The purpose of the study is to identify the main processes and phenomena that adversely affect land resources. The substantiation of the procedure for assessing the economic damage in management decisions in terms of balanced land use is another part of the purpose of the present research. Results. This article clarifies the concept of “land” and gives proof of the need for land monitoring. The latter is a system of observations of the state of the supply of land for the timely detection of changes. Their assessment, prevention and elimination of the consequences of negative impacts are also of great significance. The main factors of transformation of lands, their importance for different zones of the country, and the formation of consequences are revealed in the present study. The cost estimate of consequences requires an economic assessment of land resources. From these positions, the methodological approaches used are considered and the feasibility of using the income method is justified. The evolution of the methodological tools for assessing economic damage, and its transformation in modern conditions are analyzed in detail. Based on the assessment of land degradation under the influence of the anthropogenic factor in the mining industry, the indicators of economic damage are associated with the activities of ferrous, non-ferrous metallurgy and mining enterprises are projected. In order to ensure balance, the issue of land reclamation with identification of the reasons for non-fulfillment of reclamation works is raised. Application of the results. Methodological provisions recommended by the authors can be used in the process of state regulation of land use in order to ensure the conditions of its balance.

  14. Understanding Enterprise Architecture with Topic Modeling

    DEFF Research Database (Denmark)

    Nardello, Marco; Møller, Charles; Gøtze, John

    2018-01-01

    The next 3 years will be more important than the last 50 due to the digital transformation across industries. Enterprise Architecture (EA), the discipline that should lead enterprise responses to disruptive forces, is far from ready to drive the next wave of change. The state of the art in the di......The next 3 years will be more important than the last 50 due to the digital transformation across industries. Enterprise Architecture (EA), the discipline that should lead enterprise responses to disruptive forces, is far from ready to drive the next wave of change. The state of the art...

  15. Empowering enterprises through next-generation enterprise computing

    NARCIS (Netherlands)

    van Sinderen, Marten J.; Andrade Almeida, João

    Enterprise computing is concerned with exploiting interconnected computers to improve the efficiency and effectiveness of larger companies. Such companies form business organizations that manage various sorts of information, used by disparate groups of people, who are situated at different

  16. Early atmospheric metal pollution provides evidence for Chalcolithic/Bronze Age mining and metallurgy in Southwestern Europe.

    Science.gov (United States)

    Martínez Cortizas, Antonio; López-Merino, Lourdes; Bindler, Richard; Mighall, Tim; Kylander, Malin E

    2016-03-01

    Although archaeological research suggests that mining/metallurgy already started in the Chalcolithic (3rd millennium BC), the earliest atmospheric metal pollution in SW Europe has thus far been dated to ~3500-3200 cal.yr. BP in paleo-environmental archives. A low intensity, non-extensive mining/metallurgy and the lack of appropriately located archives may be responsible for this mismatch. We have analysed the older section (>2100 cal.yr. BP) of a peat record from La Molina (Asturias, Spain), a mire located in the proximity (35-100 km) of mines which were exploited in the Chalcolithic/Bronze Age, with the aim of assessing evidence of this early mining/metallurgy. Analyses included the determination of C as a proxy for organic matter content, lithogenic elements (Si, Al, Ti) as markers of mineral matter, and trace metals (Cr, Cu, Zn, Pb) and stable Pb isotopes as tracers of atmospheric metal pollution. From ~8000 to ~4980 cal.yr. BP the Pb composition is similar to that of the underlying sediments (Pb 15 ± 4 μg g(-1); (206)Pb/(207)Pb 1.204 ± 0.002). A sustained period of low (206)Pb/(207)Pb ratios occurred from ~4980 to ~2470 cal.yr. BP, which can be divided into four phases: Chalcolithic (~4980-3700 cal.yr. BP), (206)Pb/(207)Pb ratios decline to 1.175 and Pb/Al ratios increase; Early Bronze Age (~3700-3500 cal.yr. BP), (206)Pb/(207)Pb increase to 1.192 and metal/Al ratios remain stable; Late Bronze Age (~3500-2800 cal.yr. BP), (206)Pb/(207)Pb decline to their lowest values (1.167) while Pb/Al and Zn/Al increase; and Early Iron Age (~2800-2470 cal.yr. BP), (206)Pb/(207)Pb increase to 1.186, most metal/Al ratios decrease but Zn/Al shows a peak. At the beginning of the Late Iron Age, (206)Pb/(207)Pb ratios and metal enrichments show a rapid return to pre-anthropogenic values. These results provide evidence of regional/local atmospheric metal pollution triggered by the earliest phases of mining/metallurgy in the area, and reconcile paleo-environmental and

  17. Definition of the «Economic Security of an Enterprise» and «Safe Development of an Enterprise» Notions

    Directory of Open Access Journals (Sweden)

    Yefimova Ganna V.

    2013-11-01

    Full Text Available The necessity of this study is explained by difference of opinions regarding understanding of the “economic security of an enterprise” notion, on the one hand, and the poorly studied issue of a combination of the process of enterprise development with a necessary task of ensuring a high level of its economic security, on the other hand. Analysing, systemising and generalising results of scientific studies, the article identifies that economic security of an enterprise is an economic category, which characterises the enterprise functioning conditions. Favourable conditions of functioning ensure a high level of stability and steadiness of an enterprise and its ability of self-realisation and expanded self-reproduction. This becomes possible if an enterprise is capable of resisting external threats and preventing internal ones. Since development of an enterprise is an objective process, which takes place under conditions of uncertainty and changeability of external and internal environments, it is accompanied with a system of threats, which the system of economic security should protect an enterprise from. Taking into account the above, safe development of an enterprise is a process of consecutive transitions of the economic system from one state to another, which is not of a poorer quality than a previous one, which envisages producing new goals and creation of safe conditions for transition from one specific goal, achieved in the process of enterprise functioning, to another. The proposed definitions allow consideration of such significant issues of methodology of management of safe development of an enterprise as the diagnostics of its level and planning.

  18. Self-management evaluation by small-enterprises and micro-enterprises: Exploratory study

    Directory of Open Access Journals (Sweden)

    Lucia Clara Banchieri

    2013-09-01

    Full Text Available Purpose: To know what their habits and customs on planning, developing, information management and control of micro and small enterprises in Catalonia Design/methodology/approach: Four workshops involving 70 people from micro and small companies were carried out. The workshops were organized by institutions related to Catalan companies. The model used in the workshops was the canvas model Findings and Originality/value: The main contribution is the use of canvas as auto diagnostic tool for micro and small businesses, which has allowed us to know which is the reality of this type of business regarding management, highlighting the necessity to have an overview of the company, the necessity to foster the relationship with the external forces, and the lack of relations between key areas. Participants also know the importance of management information Research limitations/implications: The workshops were aimed at people who have contact and participate in the institutions which were performed Practical implications: This research provides a conceptual framework for the companies’ owner to make a diagnosis on your business model and how it is managed. It also allows management practices from the micro and small enterprises, to design a management control system adapted to this type of company Social implications: The results serve as a diagnostic study on the reality of small and micro enterprises, which can be used to design tools and programs that are useful for their development and survival. Originality/value: For the participants Associations aims to promote the development of micro and small enterprises, the diagnosis of the reality of these companies. For the management people, the self-diagnostic tool and for the academic community the exploratory study would allow developing a control system applicable to the reality of the micro and small enterprises.

  19. Concurrent enterprise: a conceptual framework for enterprise supply-chain network activities

    Science.gov (United States)

    Addo-Tenkorang, Richard; Helo, Petri T.; Kantola, Jussi

    2017-04-01

    Supply-chain management (SCM) in manufacturing industries has evolved significantly over the years. Recently, a lot more relevant research has picked up on the development of integrated solutions. Thus, seeking a collaborative optimisation of geographical, just-in-time (JIT), quality (customer demand/satisfaction) and return-on-investment (profits), aspects of organisational management and planning through 'best practice' business-process management - concepts and application; employing system tools such as certain applications/aspects of enterprise resource planning (ERP) - SCM systems information technology (IT) enablers to enhance enterprise integrated product development/concurrent engineering principles. This article assumed three main organisation theory applications in positioning its assumptions. Thus, proposing a feasible industry-specific framework not currently included within the SCOR model's level four (4) implementation level, as well as other existing SCM integration reference models such as in the MIT process handbook's - Process Interchange Format (PIF), the TOVE project, etc. which could also be replicated in other SCs. However, the wider focus of this paper's contribution will be concentrated on a complimentary proposed framework to the SCC's SCOR reference model. Quantitative empirical closed-ended questionnaires in addition to the main data collected from a qualitative empirical real-life industrial-based pilot case study were used: To propose a conceptual concurrent enterprise framework for SCM network activities. This research adopts a design structure matrix simulation approach analysis to propose an optimal enterprise SCM-networked value-adding, customised master data-management platform/portal for efficient SCM network information exchange and an effective supply-chain (SC) network systems-design teams' structure. Furthermore, social network theory analysis will be employed in a triangulation approach with statistical correlation analysis

  20. Design of large-scale enterprise interoperable value webs

    NARCIS (Netherlands)

    Hofman, W.J.

    2011-01-01

    Still a lot of enterprises are faced with the issue of interoperability. Whereas large enterprises are able to implement the required technology, SMEs (Small and Medium sized Enterprises) face challenges as they lack knowledge and budget. Enterprises have defined their specific semantics and

  1. Practical application of solid phase spectrophotometry in analysis of materials and goods of mining and metallurgy

    International Nuclear Information System (INIS)

    Duan Qunzhang

    1999-01-01

    The author reviewed recent development and practical application of solid phase spectrophotometry in analysis of materials and goods of mining-metallurgy. Separation and preconcentration and conditions of coloring determination, sensitivity and range of detection, as well as interference of corresponding method are discussed

  2. 12 CFR 1253.8 - Availability of new product to an Enterprise after it has been approved for the other Enterprise.

    Science.gov (United States)

    2010-01-01

    ... 12 Banks and Banking 7 2010-01-01 2010-01-01 false Availability of new product to an Enterprise after it has been approved for the other Enterprise. 1253.8 Section 1253.8 Banks and Banking FEDERAL HOUSING FINANCE AGENCY ENTERPRISES PRIOR APPROVAL FOR ENTERPRISE PRODUCTS § 1253.8 Availability of new...

  3. Metallurgy department progress report for the period 1 January to 31 December 1976

    International Nuclear Information System (INIS)

    1977-03-01

    The activities of the Metallurgy Department at Riso during 1976 are described. The work is presented in four chapters: General Materials Research, Technology and Materials Development, Fuel Elements, and Non-Destructive Testing. Furthermore, a survey is given of the department's participation in international collaboration and of its activities within education and training. A list (with abstracts) of publications and lectures by the staff during 1976 is included

  4. Metallurgy department progress report for the period 1 January to 31 December 1982

    International Nuclear Information System (INIS)

    1983-07-01

    The activities of the Metallurgy Department at Risoe during 1982 are described. The work is presented in three chapters: General Materials Research, Technology and Materials Deveopment, Fuel Elements. Furthermore, a survey is given of the department's participation in international collaboration and of its activities within education and training. A list (with abstracts) of publications and lectures by the staff during 1982 is included. (author)

  5. Metallurgy department progress report for the period 1 January to 31 December 1983

    International Nuclear Information System (INIS)

    1984-06-01

    The activities of the Metallurgy Department at Risoe during 1983 are described. The work is presented in three chapters: General Materials Research, Technology and Materials Development, and Fuel Elements. Furthermore, a survey is given of the Department's participation in international collaboration and of its activities within education and training. A list (with abstracts) of publications and lectures by the staff during 1983 is included. (author)

  6. Metallurgy Department progress report for the period 1 January to 31 December 1984

    International Nuclear Information System (INIS)

    1985-04-01

    The activities of the Metallurgy Department at Risoe during 1984 are described. The work is presented in three chapters: General Materials Research, Technology and Materials Development, and Fuel Elements. A survey is given of the Department's participation in international collaboration and of its activities within education and training. A list (with abstracts) of publications and lectures by the staff during 1984 is included. (author)

  7. Metallurgy department progress report for the period 1 January to 31 December 1980

    International Nuclear Information System (INIS)

    1981-07-01

    The activities of the Metallurgy Department at Risoe during 1980 are described. The work is presented in four chapters: General Materials Research, Technology and Materials Development, Fuel Elements, Non-Destructive Testing. Furthermore, a survey is given of the department's participation in international collaboration and of its activities within education and training. A list (with abstracts) of publications and lectures by the staff during 1980 is included. (Author)

  8. Metallurgy department progress report for the period 1 January to 31 December 1981

    International Nuclear Information System (INIS)

    1982-07-01

    The activities of the Metallurgy Department at Risoe during 1981 are described. The work is presented in three chapters: General Materials Research, Technology and Materials Development, Fuel Elements. Furthermore, a survey is given of the department's participation in international collaboration and of its activities within education and training. A list (with abstracts) of publications and lectures by the staff during 1981 is included. (author)

  9. Sourcing from an Enterprise Architecture Perspective

    DEFF Research Database (Denmark)

    Gøtze, John; Axél, Mette

    2013-01-01

    Enterprise architecture offers direct input in order to define the appropriate combination of people, components and services used to produce and deliver products and services. Sourcing, as the process of optimally organizing and procuring this inside and outside an organization, is therefore...... a central enterprise architecture concern. In this chapter we will discuss how enterprise architecture can benefit an enterprise’s sourcing strategy....

  10. IMPROVING THE TEXTILE’S ENTERPRISES KNOWLEDGE MATRIX

    Directory of Open Access Journals (Sweden)

    RADULESCU Ion Razvan

    2017-05-01

    Full Text Available The textile enterprises need adequate solutions to face the competition on the global market. Innovation leverages the enterprises competitiveness: however, improving innovation is a task of research providers in the field. The Knowledge Matrix for Innovation (KMI represents an instrument for quantifying the intangible assets of a textile enterprise. Examples of intangible assets are: innovation strategy / culture, informational resources, training methodology, relationships portfolio, IP rights etc. By improving such factors of the KMI, the textile enterprises are going to improve their competitiveness. This main aim is tackled by the Erasmus Plus – VET Project “Matrix of knowledge for innovation and competitiveness in textile enterprises - TexMatrix” (2016-2018. The red line of the project follows the definition of the KMI, the adaptation of the Benchmarking questionnaire and its implementation on the e-learning Tool, the Benchmarking study by consulting of 50 textile enterprises at consortium level, supporting the Guide with new research and innovation management solutions for the enterprises and Blended courses for 95 young trainees, based on the Guide in e-learning format. The project also aims to counsel 100 decision-factors from textile enterprises on the new solutions comprised in the Guide, within 5 Workshops. The e-learning Tool has the URL address: www.advan2tex.eu/portal/ .

  11. Logistics costs of the enterprise

    Directory of Open Access Journals (Sweden)

    Andrea Rosová

    2007-06-01

    Full Text Available The article describe a problem of specification and systematization of enterprise’s logistics costs. With in a growing division of labour, also logistics costs increase their part in enterprises total costs.Almost all decisions about products and production in general, influence logistics processes even logistics costs and performances.In present is not clear enough, which of the cost-particles are relevant fot logistics costs, because some of logistics cost-particles accounts within overhead are charged together with costs of other sorts.Substantive step in the process of the monitoring and evidence of logistics costs is definition of this, that costs of enterprise´s processes will be inclusive in logistics costs and determining points of contact with the others departments (acquisition, production, sale etc.. After the specification of meditation processes, there is a need to choose applicable parameters for the expression of logistics performances. Besides logistics costs is needed to know logistics performances equivalent herewith at a cost of, therefore from the control side have for enterprise bigger value indices expressive correlation costs and performances(e.g. share of logistics unit costs performance.At the proposal and evidence of logistics costs and performances is needed consistently entertain an individual conditions of enterprise. Because the area of processes included strongly affects the size of account logistics costs and its share part in total costs of enterprise. Logistics costs are flow line between economy and logistics of the enterprise.

  12. Summary reports of the R and D programme: recycling of non-ferrous metals (1986-1989)

    International Nuclear Information System (INIS)

    Donato, M.

    1992-01-01

    This document contains the summary reports of cost sharing research and development contracts funded under the recycling of non-ferrous metals subprogramme of the Commission of the European Communities. In particular from p.171 to 212 is described the recovery of rare earths by supported liquid membranes: synthesis and use of new selective macrocyclic and/or compartmental ligands

  13. Technology study on removal of Ra, U, Mn and F from the acid wastewater of uranium mining and metallurgy

    International Nuclear Information System (INIS)

    Wu Yongyong; Zhong Pingru; Wang Gaoshan

    2014-01-01

    The laboratory study for decreasing the concentration of Ra, U, Mn and F ions in acid wastewater of uranium mining and metallurgy was investigated based on lime neutralization-precipitation technology. The technological flowsheet was composed of removing radium by barium chloride, manganese by air aeration and fluorin by aluminum sulfate, and the quality of the disposed effluent could be accorded with the discharge criteria defined by the state, as the neutralization conditions of pH just being 8.5. Furthermore, the lower precipitation pH value can effectively decrease sediment volume, and reduce the subsequent processing pressures. The technological methods were viable and universally applicable for uranium mining and metallurgy wastewater purification. (authors)

  14. System of Enterprise Reputation Management

    Directory of Open Access Journals (Sweden)

    Derevianko Olena. H.

    2014-03-01

    Full Text Available The article offers a system of enterprise reputation management directed at increase of economic benefits from formation and maintenance of high reputation in the result of maximisation of the volume of the incoming cash flows of the enterprise and also their duration and stability. It proves that reputation management, which allows achievement of economic goals of the enterprise, should be directed at key groups of stakeholders: growth of products sales is ensured by consumers, growth of internal stability – by enterprise personnel, growth of external stability – by society, including authority bodies, growth of business value – by investors, owners and partners. The article describes components of the system of enterprise reputation management, the degree of development of which are determined by three vectors: interaction with stakeholders and level of their feedback: messaging, informing, convincing and attracting; activity of the used instruments of reputation management, regularity and intensity, and also quantitative indicators of their application within the framework of directions of the product PR, corporate PR and IR, internal PR, GR and PR-CSR; level of organisational pre-requisites (functional, system and strategic of the system of reputation management.

  15. Chromium content in human skin after in vitro application of ordinary cement and ferrous-sulphate-reduced cement

    DEFF Research Database (Denmark)

    Fullerton, A; Gammelgaard, Bente; Avnstorp, C

    1993-01-01

    The amount of chromium found in human skin after in vitro application of cement suspensions on full-thickness human skin in diffusion cells was investigated. Cement suspensions made from ordinary Portland cement or Portland cement with the chromate reduced with added ferrous sulphate were used....... The cement suspensions were either applied on the skin surface under occlusion for 48 h or applied repeatedly every 24 h for 96 h. No statistically significant difference in chromium content of skin layers between skin exposed to ordinary Portland cement, skin exposed to cement with added ferrous sulphate...... and unexposed skin was observed, despite a more permeable skin barrier at the alkaline pH of the cement suspensions, i.e., pH 12.5. Increased chromium levels in epidermis and dermis were seen when ordinary Portland cement was applied as a suspension with added sodium sulphate (20%) on the skin surface for 96 h...

  16. Systems Thinking for the Enterprise: A Thought Piece

    Science.gov (United States)

    Rebovich, George

    This paper suggests a way of managing the acquisition of capabilities for large-scale government enterprises that is different from traditional "specify and build" approaches commonly employed by U.S. government agencies in acquiring individual systems or systems of systems (SoS). Enterprise capabilities evolve through the emergence and convergence of information and other technologies and their integration into social, institutional and operational organizations and processes. Enterprise capabilities evolve whether or not the enterprise has processes in place to actively manage them. Thus the critical role of enterprise system engineering (ESE) processes should be to shape, enhance and accelerate the "natural" evolution of enterprise capabilities. ESE processes do not replace or add a layer to traditional system engineering (TSE) processes used in developing individual systems or SoS. ESE processes should complement TSE processes by shaping outcome spaces and stimulating interactions among enterprise participants through marketlike mechanisms to reward those that create innovation which moves and accelerates the evolution of the enterprise.

  17. Enabler for the agile virtual enterprise

    Science.gov (United States)

    Fuerst, Karl; Schmidt, Thomas; Wippel, Gerald

    2001-10-01

    In this presentation, a new approach for a flexible low-cost Internet extended enterprise (project FLoCI-EE) will be presented. FLoCI-EE is a project in the fifth framework program of the European commission with 8 partners from 4 countries, which started in January 2001 and will be finished in December 2003. The main objective of FLoCI-EE is the development of a software prototype, which enables flexible enterprise cooperation with the aim to design, manufacture and sell products commonly, independent of enterprise borderlines. The needed IT-support includes functions of product data management (PDM), enterprise resource planning (ERP), supply chain management (SCM) and customer relationship management (CRM). Especially for small and medium sized enterprises, existing solutions are too expensive and inflexible to be of use under current turbulent market conditions. The second part of this paper covers the item Web Services, because in the role-specific support approach of FLoCI-EE, there are user- interface-components, which are tailored for specific roles in an enterprise. These components integrate automatically the services of the so-called basic-components, and the externally offered Web Services like UDDI.

  18. Discussion on enterprise technical standard management work

    International Nuclear Information System (INIS)

    Li Xinyou

    2010-01-01

    The technical standard management is an important part of enterprise information work, also the basis of enterprise standardization work. Only by rational and orderly management, can it exert maximum effectiveness, provide reliable support for the production and business of enterprise. (author)

  19. Application of vacuum metallurgy to separate pure metal from mixed metallic particles of crushed waste printed circuit board scraps.

    Science.gov (United States)

    Zhan, Lu; Xu, Zhenming

    2008-10-15

    The principle of separating pure metal from mixed metallic particles (MMPs) byvacuum metallurgy is that the vapor pressures of various metals at the same temperature are different As a result, the metal with high vapor pressure and low boiling point can be separated from the mixed metals through distillation or sublimation, and then it can be recycled through condensation under a certain condition. The vacuum metallurgy separation (VMS) of MMPs of crushed waste printed circuit boards (WPCBs) has been studied in this paper. Theoretical analyses show that the MMPs (copper, zinc, bismuth, lead, and indium, for example) can be separated by vacuum metallurgy. The copper particles (0.15-0.20 mm) and zinc particles (<0.30 mm) were chosen to simulate the MMPs of crushed WPCBs. Experimental results show that the separated efficiency of zinc in the copper-rich particles achieves 96.19 wt % when the vacuum pressure is 0.01-0.10 Pa, the heating temperature is 1123 K, and the heating time is 105 min. Under this operation condition, the separated efficiency of zinc in the copper-rich particles from crushed WPCBs achieves 97.00 wt % and the copper purity increases from 90.68 to 99.84 wt %.

  20. Risk Analysis of Telecom Enterprise Financing

    Institute of Scientific and Technical Information of China (English)

    YU Hua; SHU Hua-ying

    2005-01-01

    The main research objects in this paper are the causes searching and risk estimating method for telecom enterprises' financial risks. The multi-mode financing for telecom enterprises makes it flexible to induce the capital and obtain the profit by corresponding projects. But there are also potential risks going with these financing modes. After making analysis of categories and causes of telecom enterprises' financing risk, a method by Analytic Hierarchy Process (AHP) is put forward to estimating the financing risk. And the author makes her suggestion and opinion by example analysis, in order to provide some ideas and basis for telecom enterprise's financing decision-making.

  1. Shaping the Enterprise By Design

    DEFF Research Database (Denmark)

    Gøtze, John; Guenther, Milan

    2017-01-01

    Too often, ambitious service design initiatives that require complex enterprises to change fall short of delivering on their intended outcomes.......Too often, ambitious service design initiatives that require complex enterprises to change fall short of delivering on their intended outcomes....

  2. 12 CFR 1252.1 - Enterprise portfolio holding criteria.

    Science.gov (United States)

    2010-01-01

    ... 12 Banks and Banking 7 2010-01-01 2010-01-01 false Enterprise portfolio holding criteria. 1252.1 Section 1252.1 Banks and Banking FEDERAL HOUSING FINANCE AGENCY ENTERPRISES PORTFOLIO HOLDINGS § 1252.1 Enterprise portfolio holding criteria. The Enterprises are required to comply with the portfolio holdings...

  3. Metallurgy of steels for PWR pressure vessels

    International Nuclear Information System (INIS)

    Kepka, M.; Mocek, J.; Barackova, L.

    1980-01-01

    A survey and the chemical compositions are presented of reactor pressure vessel steels. The metallurgy is described of steel making for pressure vessels in Japan and the USSR. Both acidic and alkaline open-hearth steel is used for the manufacture of ingots. The leading world manufacturers of forging ingots for pressure vessels, however, exclusively use electric steel. Vacuum casting techniques are exclusively used. Experience is shown gained with the introduction of the manufacture of forging ingots for pressure vessels at SKODA, Plzen. The metallurgical procedure was tested utilizing alkaline open hearths, electric arc furnaces and facilities for vacuum casting of steel. Pure charge raw materials should be used for securing high steel purity. Prior to forging pressure vessel rings, not only should sufficiently big bottoms and heads be removed but also the ingot middle part should be scrapped showing higher contents of impurities and nonhomogeneous structure. (B.S.)

  4. Metallurgy of steels for PWR pressure vessels

    Energy Technology Data Exchange (ETDEWEB)

    Kepka, M; Mocek, J; Barackova, L [Skoda, Plzen (Czechoslovakia)

    1980-09-01

    A survey and the chemical compositions are presented of reactor pressure vessel steels. The metallurgy is described of steel making for pressure vessels in Japan and the USSR. Both acidic and alkaline open-hearth steel is used for the manufacture of ingots. The leading world manufacturers of forging ingots for pressure vessels, however, exclusively use electric steel. Vacuum casting techniques are exclusively used. Experience is shown gained with the introduction of the manufacture of forging ingots for pressure vessels at SKODA, Plzen. The metallurgical procedure was tested utilizing alkaline open hearths, electric arc furnaces and facilities for vacuum casting of steel. Pure charge raw materials should be used for securing high steel purity. Prior to forging pressure vessel rings, not only should sufficiently big bottoms and heads be removed but also the ingot middle part should be scrapped showing higher contents of impurities and nonhomogeneous structure.

  5. 77 FR 56837 - Enterprise Intrastate LLC; Notice of Filing

    Science.gov (United States)

    2012-09-14

    ... DEPARTMENT OF ENERGY Federal Energy Regulatory Commission [Docket No. PR12-34-000] Enterprise Intrastate LLC; Notice of Filing Take notice that on September 6, 2012, Enterprise Intrastate LLC (Enterprise.... Enterprise Intrastate is revising its SOC to replace all references to ``Enterprise Intrastate L.P.'' with...

  6. Definition of an Object-Oriented Modeling Language for Enterprise Architecture

    OpenAIRE

    Lê, Lam Son; Wegmann, Alain

    2005-01-01

    In enterprise architecture, the goal is to integrate business resources and IT resources in order to improve an enterprises competitiveness. In an enterprise architecture project, the development team usually constructs a model that represents the enterprise: the enterprise model. In this paper, we present a modeling language for building such enterprise models. Our enterprise models are hierarchical object-oriented representations of the enterprises. This paper presents the foundations of o...

  7. [Concomitant influence of occupational and social risk factors on health of workers engaged into powder metallurgy].

    Science.gov (United States)

    Shur, P Z; Zaĭtseva, N V; Kostarev, V G; Lebedeva-Nesevria, N A; Shliapnikov, D M

    2012-01-01

    Results of health risk evaluation in workers engaged into powder metallurgy, using complex of hygienic, medical, epidemiologic and sociologic studies, enable to define priority occupational and social risk factors, to assess degree of their influence on the workers' health and to identify occupationally induced diseases.

  8. 76 FR 70438 - Enterprise Intrastate L.P., Enterprise Texas Pipeline LLC; Notice of Filing

    Science.gov (United States)

    2011-11-14

    ... DEPARTMENT OF ENERGY Federal Energy Regulatory Commission [Docket No. PR12-4-000; Docket No. PR12-5-000; Not Consolidated] Enterprise Intrastate L.P., Enterprise Texas Pipeline LLC; Notice of Filing Take notice that on November 1, 2011, the applicants listed above filed a revised Statement of...

  9. Study of the dose response of the system ferrous ammonium sulfate–sucrose–xylenol orange in acid aqueous solution

    International Nuclear Information System (INIS)

    Juarez-Calderon, J.M.; Negron-Mendoza, A.; Ramos-Bernal, S.

    2014-01-01

    An aqueous solution of ammonium ferrous sulfate–sucrose–xylenol orange in sulfuric acid (FSX) is proposed as a dosimetric system for the processes of gamma irradiation in a range between 0.3 and 6 Gy. This system is based on the indirect oxidation of ferrous ion by an organic compound (sucrose) to ferric ion and on the formation of a color complex of Fe 3+ in an acidic medium with xylenol orange (a dye). After gamma radiation, an observable change occurs in the color of the system. Irradiation was executed at three different temperatures (13 °C, 22 °C, and 40 °C). A spectrometric readout method at 585 nm was employed to evaluate the system's dose response. In all of the cases analyzed, the responses had a linear behavior, and a slight effect of irradiation temperature was observed. Post-irradiation response was also evaluated and showed the stability of the solutions 24 h after the irradiation. The results obtained suggest that FSX might be used as a dosimeter for low doses of gamma irradiation because it provides a stable signal, good reproducibility, and an accessible technique for analysis. - Highlights: • The system ferrous-sucrose-xylenol is reproducibility with less than 5% error. • The dosimeter has low cost and easy readout using UV-vis spectrometry, and the response is stable for several days. • The system proposed is suitable for low irradiation doses

  10. Production of uranium in Navoi Mining and Metallurgy Combinat, Uzbekistan

    International Nuclear Information System (INIS)

    Kuchersky, N.; Tolstov, E.A.; Mazurkevich, A.P.; Inozemzev, S.B.

    2001-01-01

    Full text: Under the conditions of constantly increasing level of development of the nuclear power, it is inevitable that the uranium stockpiles accumulated to 1985 will soon be depleted. This consideration underlies the development concept of uranium production in the Navoi Mining and Metallurgy Combinat, Uzbekistan. Because this product has become a source of hard currency revenues for the Republic, there will be a significant increase in the processed ore and output of uranium oxide within the next few years. Uranium production in the Navoi Mining and Metallurgy Combinat represents a full-cycle operations ranging from geological survey through hydrometallurgical processing resulting in the output of uranium concentrate in the form of uranium protoxide-oxide (U 3 O 8 ). The NMMC uranium operations include the Hydrometallurgical Plant and three facilities accomplishing ISL mining facilities. A successful start on the development of the Uchkuduk deposit by ISL method in the 1960s gave rise to scientific and production approach for development of other uranium deposits of the infiltration bedded (sandstone) type. Uranium recovery by ISL has become a separate mining branch within the 30-year period of its history and the contribution of this branch in uranium production has steadily grown. Since 1995 all uranium produced by Navoi Mining and Metallurgy Combinat is attributed to ISL. During this evolution period of the ISL method, a whole range of systematic scientific research and practical works were carried out covering improvement of process flowsheets, equipment, operational methods and techniques for particular mining conditions at those specific sites. In co-operation with design and scientific research institutions, a significant number of scientific researches, test works, design and engineering projects were achieved in order to create optimal conditions for ISL mining and further processing of pregnant solutions by sorption as well as to appropriately equip

  11. Based on the core competitiveness of enterprise innovation culture research

    Institute of Scientific and Technical Information of China (English)

    韩 军

    2017-01-01

    In the spring tide of market economy at present, the enterprise is a must to survive in order to achieve innovation, promote enterprise's core competitiveness. Enterprise innovation culture, the promotion enterprise's core competitiveness plays an important role in promoting, therefore must complete enterprise innovation culture. Therefore, put forward by enterprise innovation culture, promote enterprise's core competitiveness.

  12. Assessment of heavy metals exposure, noise and thermal safety in the ambiance of a vacuum metallurgy separation system for recycling heavy metals from crushed e-wastes.

    Science.gov (United States)

    Zhan, Lu; Xu, Zhenming

    2014-12-01

    Vacuum metallurgy separation (VMS) is a technically feasible method to recover Pb, Cd and other heavy metals from crushed e-wastes. To further determine the environmental impacts and safety of this method, heavy metals exposure, noise and thermal safety in the ambiance of a vacuum metallurgy separation system are evaluated in this article. The mass concentrations of total suspended particulate (TSP) and PM10 are 0.1503 and 0.0973 mg m(-3) near the facilities. The concentrations of Pb, Cd and Sn in TSP samples are 0.0104, 0.1283 and 0.0961 μg m(-3), respectively. Health risk assessments show that the hazard index of Pb is 3.25 × 10(-1) and that of Cd is 1.09 × 10(-1). Carcinogenic risk of Cd through inhalation is 1.08 × 10(-5). The values of the hazard index and risk indicate that Pb and Cd will not cause non-cancerous effects or carcinogenic risk on workers. The noise sources are mainly the mechanical vacuum pump and the water cooling pump. Both of them have the noise levels below 80 dB (A). The thermal safety assessment shows that the temperatures of the vacuum metallurgy separation system surface are all below 303 K after adopting the circulated water cooling and heat insulation measures. This study provides the environmental information of the vacuum metallurgy separation system, which is of assistance to promote the industrialisation of vacuum metallurgy separation for recovering heavy metals from e-wastes. © The Author(s) 2014.

  13. Enterprise Oil gets going

    International Nuclear Information System (INIS)

    Ross, Priscilla.

    1996-01-01

    Enterprise Oil is a mature United Kingdom independent oil exploration and production company. In its early years, with the success of the Nelson platform in the North Sea, the company had been well rated by financial analysts in the City of London. Enterprise was floated as an independent company on the International Stock Exchange in London in 1984 having previously been part of the establishment being formed by the Government from the oil and production interests of British Gas on the UK Continental shelf. Relationships with the City suffered, however, as a result of the unsuccessful outcome of moves by the company to take over Lasmo, the only other UK independent oil company of comparable magnitude. Pedestrian financial results and poor exploration results led to Enterprise dividends being stuck in a rut from 1992 onwards. This report, however, shows how that situation is changing so that the company's share price has been reaching new highs. Enterprise has been adding quantitative value to the company through swaps, farm-in deals and licensed acquisitions and now has interests in core income producing areas in the UK, Norway, Denmark and Italy. (UK)

  14. PNGMDR 2013-2015. ANDRA's opinion on the development of sector of recycling of VLA ferrous metallic waste

    International Nuclear Information System (INIS)

    2014-01-01

    The scope of this report is to state the ANDRA's opinion on the recycling of very-low-level metallic wastes, and mainly ferrous metallic wastes which are the main stream of them. After having evoked a study jointly performed by EDF, AREVA, the CEA and the ANDRA to assess the technical and economic feasibility of a valorisation of very-low-level metallic wastes in the nuclear sector, this study proposes an assessment of ferrous metals which might be recycled over about thirty years. After having outlined the strong motivation of the ANDRA for such a recycling, the report proposes an overview of the heterogeneous stream of metallic wastes, by distinguishing scrap materials from very heterogeneous origins like those brought to the Cires storage centre, and those with more homogeneous origins (for example, from dismantling activities). The next part proposes an overview of various non coordinated initiatives, notably by the ANDRA, on different storage sites. The report identifies the keys for a successful recycling of contaminated metals in Europe, and the main challenges for the recycling of very-low-level ferrous metal in France (in competition with direct storage, and with the application of the risk-related regulation for some metallic wastes). Some proposals made by the ANDRA are then stated: a reference industrial scheme, and a coordination of actors under the auspices of the State

  15. Participatory Governance in Social Enterprise

    DEFF Research Database (Denmark)

    Pestoff, Victor Alexis; Hulgård, Lars

    2016-01-01

    This paper emphasizes the importance of participative governance in the study of social enterprise. Furthermore, it argues that social enterprise must be analyzed through a multi-dimensional perspective. The EMES approach is based on three dimensions emphasizing the social, economic, and politica...

  16. Strategy development marketing commercial enterprise

    OpenAIRE

    Shatalov D. S.; Hamidova O. M.

    2016-01-01

    in the scientific article the necessity of development and implementation of marketing strategies in the activity of any commercial enterprise, we give a meaningful description of the concept of «marketing strategy» and develop requirements for the selection strategy of trade enterprise.

  17. Powder metallurgy: Solid and liquid phase sintering of copper

    Science.gov (United States)

    Sheldon, Rex; Weiser, Martin W.

    1993-01-01

    Basic powder metallurgy (P/M) principles and techniques are presented in this laboratory experiment. A copper based system is used since it is relatively easy to work with and is commercially important. In addition to standard solid state sintering, small quantities of low melting metals such as tin, zinc, lead, and aluminum can be added to demonstrate liquid phase sintering and alloy formation. The Taguchi Method of experimental design was used to study the effect of particle size, pressing force, sintering temperature, and sintering time. These parameters can be easily changed to incorporate liquid phase sintering effects and some guidelines for such substitutions are presented. The experiment is typically carried out over a period of three weeks.

  18. Surface metallurgy of cemented carbide tools

    International Nuclear Information System (INIS)

    Chopra, K.L.; Kashyap, S.C.; Rao, T.V.; Rajagopalan, S.; Srivastava, P.K.

    1983-01-01

    Transition metal carbides, owing to their high melting point, hardness and wear resistance, are potential candidates for specific application in rockets, nuclear engineering equipment and cutting tools. Tungsten carbide sintered with a binder (either cobalt metal or a mixture of Co + TiC and/or TaC(NbC)) is used for cutting tools. The surface metallurgy of several commercially available cemented carbide tools was studied by Auger electron spectroscopy and X-ray photoelectron spectroscopy techniques. The tool surfaces were contaminated by adsorbed oxygen up to a depth of nearly 0.3 μm causing deterioration of the mechanical properties of the tools. Studies of fractured samples indicated that the tool surfaces were prone to oxygen adsorption. The fracture path passes through the cobalt-rich regions. The ineffectiveness of a worn cutting tool is attributed to the presence of excessive iron from the steel workpiece and carbon and oxygen in the surface layers of the tool. The use of appropriate hard coatings on cemented carbide tools is suggested. (Auth.)

  19. The metallurgy of superalloys part 2

    International Nuclear Information System (INIS)

    Abdelazim, M.E.; Hammad, F.H.

    1990-01-01

    This is part II of the report titled 'the metallurgy of superalloys'. It deals with the effect of heat treatment and operating conditions (thermal exposure and environment) on the mechanical properties of superalloys. The heat treatment is important in the development of superalloys through that it controls type, amount, size shape and distribution of the precipitate and the grain size of the matrix. The thermal exposure leads to reduction in the amount of the primary carbides and to precipitation of secondary carbides. Also it leads to the agglomeration and coarsening of gamma or the transformation of gamma phase to phase. The environment may lead to the internal oxidation, carburization, decarburization or sulphidization of the superalloys which may result in the degradation of their mechanical properties. This part gives also an example of applications of superalloys in the field of nuclear reactors especially high temperature-gas cooled reactors. Joined with this part a table which contains the major superalloys including its chemical analysis, creep rupture strength and some of its applications. 1 tab

  20. The metallurgy of superalloys part 1

    International Nuclear Information System (INIS)

    Abdelazim, M.E.; Hammad, F.H.

    1990-01-01

    This is part I of the report titled 'the metallurgy of superalloys'. In this part the structure, phases and systems of superalloys are reviewed. The role of alloying elements in the design of superalloys and the mechanical properties of superalloys are also reviewed. Superalloys are important in high temperature technology, especially above 700 degree c. They are 'super' mainly because their creep and stress rupture resistances are very high. Superalloys are based on an austenitic matrix including secondary phases, mainly gamma precipitates, inter and intragranular carbides mainly M 23 C 6 and M 6 C. They are classified into three systems, Ni-base, Fe-Ni base and Ce-base alloys. Different alloying elements mainly Cr, Mo, Al, Ti are added to increase the strength either by solid solution hardening (Cr, Mo, Al), precipitation hardening (A 1, Ti to produce gamma) or by dispersion hardening (Cr, Mo to form M 23 C 6 and M 6 C carbides) and to increase the oxidation resistance (Cr, Al). 3 tab., 2 fig

  1. A major advance in powder metallurgy

    Science.gov (United States)

    Williams, Brian E.; Stiglich, Jacob J., Jr.; Kaplan, Richard B.; Tuffias, Robert H.

    1991-01-01

    Ultramet has developed a process which promises to significantly increase the mechanical properties of powder metallurgy (PM) parts. Current PM technology uses mixed powders of various constituents prior to compaction. The homogeneity and flaw distribution in PM parts depends on the uniformity of mixing and the maintenance of uniformity during compaction. Conventional PM fabrication processes typically result in non-uniform distribution of the matrix, flaw generation due to particle-particle contact when one of the constituents is a brittle material, and grain growth caused by high temperature, long duration compaction processes. Additionally, a significant amount of matrix material is usually necessary to fill voids and create 100 percent dense parts. In Ultramet's process, each individual particle is coated with the matrix material, and compaction is performed by solid state processing. In this program, Ultramet coated 12-micron tungsten particles with approximately 5 wt percent nickel/iron. After compaction, flexure strengths were measured 50 percent higher than those achieved in conventional liquid phase sintered parts (10 wt percent Ni/Fe). Further results and other material combinations are discussed.

  2. Extractive metallurgy of zirconium--1945 to the present

    International Nuclear Information System (INIS)

    Franklin, D.G.; Adamson, R.B.

    1984-01-01

    Although the history of the reduction of zirconium dates from 1824 and the first ductile zirconium metal was produced in the laboratory in 1914, modern reduction practice was pioneered by the U.S. Bureau of Mines starting in 1945. This paper reviews the history of the extractive metallurgy of zirconium from the early work of W. J. Kroll and co-workers at the Bureau of Mines in Albany, Ore., through the commercial development of the production of reactor-grade zirconium metal which was spurred by the requirements of the Naval Reactor Program and the development of commercial nuclear power. Technical subjects covered include processes for opening the ore, zirconium-hafnium separation, chlorination of zirconium oxide, reduction processes, and electrowinning of zirconium metal. Proposed new processes and process modifications are reviewed

  3. Social enterprise: theoretical basis and perespectives

    Directory of Open Access Journals (Sweden)

    Julian Narlev

    2017-07-01

    Full Text Available Since the 1980s the issues of social enterprises have gained particular popularity, practical and applied, as well as scientific significance. For a short period of time - almost half a century - social enterprises have become an integral part of education and academic research; they have turned into factors affecting noticeably the social and economic policy. The formation and development of social enterprises are the consequence of the profound social, demographic, cultural, global and public changes - the result of capitalism and its cornerstone, the enterprise. This contemporary and innovative theory is a natural extension of the strategies for change in societies and the world - both globally, and in response to the non-profit, public and business sectors - in an attempt to solve the topical and important issues of the time. In view of the circumstances given above, the present study aims to study and analyse - in the theoretical plan basis aspects of social enterprises, and on that to draw and systematize their perspectives for development.

  4. A domestic model for successful implementation of enterprise resource planning (ERP systems in Iranian manufacturing enterprises

    Directory of Open Access Journals (Sweden)

    Mohammad Rahmani

    2012-01-01

    Full Text Available This research investigates the human-behavioral dimension of technology acceptance in enterprises. It is evident that accepting a technology depends on the underlying circumstances of the environment. We have approached this issue from two different angles of social and technological architecture. The research tries to explore proper enterprise architecture for ERP system acceptance. Social Architecture (SA is defined as the set of circumstances that makes people behave in a particular way. So behavior of persons (employees of an enterprise can be a function of SA. Hence acceptance of a system can be dictated by SA and manipulating SA can result in desirable success for a technology system. We have achieved various variables of social architecture and have examined their relevance to system acceptance and success in related enterprises (research domain beside technological architecture variables. The results have indicated that a special form of social and technological architecture can lead to success for ERP system in the enterprises of the research domain. This gave us a model of architecture.

  5. Optimisation of Investment Resources at Small Enterprises

    Directory of Open Access Journals (Sweden)

    Shvets Iryna B.

    2014-03-01

    Full Text Available The goal of the article lies in the study of the process of optimisation of the structure of investment resources, development of criteria and stages of optimisation of volumes of investment resources for small enterprises by types of economic activity. The article characterises the process of transformation of investment resources into assets and liabilities of the balances of small enterprises and conducts calculation of the structure of sources of formation of investment resources in Ukraine at small enterprises by types of economic activity in 2011. On the basis of the conducted analysis of the structure of investment resources of small enterprises the article forms main groups of criteria of optimisation in the context of individual small enterprises by types of economic activity. The article offers an algorithm and step-by-step scheme of optimisation of investment resources at small enterprises in the form of a multi-stage process of management of investment resources in the context of increase of their mobility and rate of transformation of existing resources into investments. The prospect of further studies in this direction is development of a structural and logic scheme of optimisation of volumes of investment resources at small enterprises.

  6. List of unclassified documents by the staff of Metallurgy Division, AERE Harwell from January 1979 to July 1980

    International Nuclear Information System (INIS)

    Smith, N.C.

    1980-12-01

    This list constitutes unclassified material published or presented between January 1979 and July 1980, by the staff of Metallurgy Division. It covers reports, memoranda, articles in periodicals, conference papers, books and patent specifications. (author)

  7. Diagnosis in the Enterprise Management System

    Directory of Open Access Journals (Sweden)

    Skrynkovskyy Ruslan M.

    2016-08-01

    Full Text Available The aim of the article is to define the role and place of the diagnosis management system in the structure of the task system of the enterprise diagnosis. There suggested the essence of the concept of «diagnosis of the enterprise», which is understood as the process of identification, analysis and evaluation of the enterprise state and trends in its changes (changes of the state on the basis of relevant business indicators in order to develop recommendations on the elimination of problematic points and weaknesses in the functioning of the enterprise to ensure a qualitatively new level of its development and formation of prospects with consideration to the consequences of violation of the legislation in the field of economics and enterprise management and law (legal responsibility for the violation of the labor law, tax law, law on protection of economic competition, law on trade secret, etc.. It was found that the diagnosis in the system of enterprise management: 1 is a structural component (or a partial diagnosis task in a group of private diagnosis tasks in the system of diagnosis task of the enterprise activity; 2 as a sub-function of the control function (as a general function of management includes such components as: assessment (identification of key features, characteristics, parameters (indexes, indicators, properties; analysis (a thorough study of the structure, dynamics, trends, etc.; identification (involves determination of deviations of parameters from the criteria and/or standards, formulation of diagnosis. Prospects for further research in this direction are the development of methods for quantitative assessment of the effectiveness of the management system with the purpose of its introducing in practical activities of enterprises, namely in the processes of decision-making.

  8. Metallurgy department progress report for the period 1 January to 31 December 1978

    International Nuclear Information System (INIS)

    1979-04-01

    The activities of the metallurgy department at Risoe during 1978 are described. The work is presented in four chapters: General materials research, technology and materials development, fuel elements, and non-destructive testing. Furthermore, a survey is given of the depratment's participation in international collaboration and of its activities within education and training. A list (with abstracts) of publications and lectures by the staff during 1978 is included. (author)

  9. Metallurgy Department progress report for the period 1 January to 31 December 1985

    International Nuclear Information System (INIS)

    Schroeder Pedersen, A.; Bilde Soerensen, J.B.

    1986-04-01

    The activities of the Metallurgy department at Risoe during 1985 are described. The work is presented in four chapters: General Materials Research, Technology and Materials Development, Chemical and Electrochemical Energy Research and Development, and Fuel elements. A survey is given of the Department's participation in international collaboration and of its activities within education and training. A list (with abstracts) of publications and lectures by the staff during 1985 is included. (author)

  10. Metallurgy Department progress report for the period 1 January to 31 December 1986

    International Nuclear Information System (INIS)

    Schroeder Pedersen, A.; Bilde-Soerensen, J.B.

    1987-04-01

    The activities of the Metallurgy Department at Risoe during 1986 are described. The work is presented in four chapters: General Materials Research, Technology and Materials Development, Chemical and Electrochemical Energy Research and Development, and Fuel Elements. A survey is given of the Department's participation in international collaboration and of its activities within education and training. A list (with abstracts) of publications and lectures by the staff during 1986 is included. (editors)

  11. Metallurgy department progress report for the period 1 January to 31 December 1975

    International Nuclear Information System (INIS)

    1976-03-01

    The activities of the Metallurgy Department at Risoe during 1975 are described. The work is presented in four chapters: General Materials Research, Technology and Materials Development, Fuel Elements, and Non-Destructive Testing. Furthermore, a survey is given of the department's participation in international collaboration and of its activities within education and training. A list (with abstracts) of publications and lectures by the staff during 1975 is included. (author)

  12. Metallurgy department progress report for the period 1 January to 31 December 1977

    International Nuclear Information System (INIS)

    1978-03-01

    The activities of the Metallurgy Department at Risoe during 1977 are described. The work is presented in four chapters: General Materials Research, Technology and Materials Development, Fuel elements, and Non-Destructive Testing. Furthermore, a survey is given of the department's participation in international collaboration and of its activities within education and training. A list (with abstracts) of publications and lectures by the staff during 1977 is included. (author)

  13. Terms of Address in the Chinese Business Enterprise

    Science.gov (United States)

    Huang, Xiaoyan; Sultan, Robert

    2014-01-01

    This study examines terms of address currently used by employees of Chinese business enterprises. The authors find that a speaker's address selections are related significantly to the gender of the speaker, the location of the enterprise in Eastern or Western China, and the ownership type of the enterprise; that is, whether the enterprise is…

  14. [Use of powder metallurgy for development of implants of Co-Cr-Mo alloy powder].

    Science.gov (United States)

    Dabrowski, J R

    2001-04-01

    This paper discusses the application of powder metallurgy for the development of porous implantation materials. Powders obtained from Co-Cr-Mo alloy with different carbon content by water spraying and grinding, have been investigated. Cold pressing and rotary re-pressing methods were used for compressing the powder. It was found that the sintered materials obtained from water spraying have the most advantageous properties.

  15. Some observations on the physical metallurgy of nickel alloy weld metals

    International Nuclear Information System (INIS)

    Skillern, C.G.; Lingenfelter, A.C.

    1982-01-01

    Numerous nickel alloys play critical roles in various energy-related applications. Successful use of these alloys is almost always dependent on the availability of acceptable welding methods and welding products. An understanding of the physical metallurgy of these alloys and their weld metals and the interaction of weld metal and base metal is essential to take full advantage of the useful properties of the alloys. To illustrate this point, this paper presents data for two materials: INCONEL alloy 718 and INCONEL Welding Electrode 132. 8 figures, 9 tables

  16. Experimental Characterization of Aluminum-Based Hybrid Composites Obtained Through Powder Metallurgy

    Science.gov (United States)

    Marcu, D. F.; Buzatu, M.; Ghica, V. G.; Petrescu, M. I.; Popescu, G.; Niculescu, F.; Iacob, G.

    2018-06-01

    The paper presents some experimental results concerning fabrication through powder metallurgy (P/M) of aluminum-based hybrid composites - Al/Al2O3/Gr. In order to understand the mechanisms that occur during the P/M processes of obtaining Al/Al2O3/Gr composite, we correlated the physical characteristics with their micro-structural characteristics. The characterization was performed using analysis techniques specific for P/M process, SEM-EDS and XRD analyses. Micro-structural characterization of the composites has revealed fairly uniform distribution this resulting in good properties of the final composite material.

  17. Financing Agricultural Enterprises By Cooperative Societies In ...

    African Journals Online (AJOL)

    The study was on cooperative societies financing of agricultural enterprises in Mbaise Area of Imo State, Nigeria. The objectives includes, identification of sources of finance for the cooperative societies and types of agricultural enterprises financed, profitability of the enterprises and the members or loan beneficiaries ...

  18. Retraction Note to: Ultra-High Strength and Ductile Lamellar-Structured Powder Metallurgy Binary Ti-Ta Alloys

    Science.gov (United States)

    Liu, Yong; Xu, Shenghang; Wang, Xin; Li, Kaiyang; Liu, Bin; Wu, Hong; Tang, Huiping

    2018-05-01

    The editors and authors have retracted the article, "Ultra-High Strength and Ductile Lamellar-Structured Powder Metallurgy Binary Ti-Ta Alloys" by Yong Liu, Shenghang Xu, Xin Wang, Kaiyang Li, Bin Liu, Hong Wu, and Huiping Tang (https://doi.org/10.1007/s11837-015-1801-1).

  19. Self-Paced Tutorial Courses for Mineral Science - Metallurgy Departments. Final Progress Report (July 1975-August 1980).

    Science.gov (United States)

    Twidwell, L. G.

    Four courses in extractive metallurgy (Pyrometallurgy, Hydrometallurgy, Electrometallurgy; and Physical Chemistry of Iron and Steel) were prepared in a modular, self-paced format. Development of the course materials included: (1) preparation of course outlines by unit coordinators and advisory committees; (2) approval of course outlines (included…

  20. Virtual Enterprise: Transforming Entrepreneurship Education

    Science.gov (United States)

    Borgese, Anthony

    2011-01-01

    Entrepreneurship education is ripe for utilizing experiential learning methods. Experiential methods are best learned when there is constant immersion into the subject matter. One such transformative learning methodology is Virtual Enterprise (VE). Virtual Enterprise is a multi-faceted, experiential learning methodology disseminated by the City…